National Elevation Dataset

Science.gov (United States)

,

2002-01-01

The National Elevation Dataset (NED) is a new raster product assembled by the U.S. Geological Survey. NED is designed to provide National elevation data in a seamless form with a consistent datum, elevation unit, and projection. Data corrections were made in the NED assembly process to minimize artifacts, perform edge matching, and fill sliver areas of missing data. NED has a resolution of one arc-second (approximately 30 meters) for the conterminous United States, Hawaii, Puerto Rico and the island territories and a resolution of two arc-seconds for Alaska. NED data sources have a variety of elevation units, horizontal datums, and map projections. In the NED assembly process the elevation values are converted to decimal meters as a consistent unit of measure, NAD83 is consistently used as horizontal datum, and all the data are recast in a geographic projection. Older DEM's produced by methods that are now obsolete have been filtered during the NED assembly process to minimize artifacts that are commonly found in data produced by these methods. Artifact removal greatly improves the quality of the slope, shaded-relief, and synthetic drainage information that can be derived from the elevation data. Figure 2 illustrates the results of this artifact removal filtering. NED processing also includes steps to adjust values where adjacent DEM's do not match well, and to fill sliver areas of missing data between DEM's. These processing steps ensure that NED has no void areas and artificial discontinuities have been minimized. The artifact removal filtering process does not eliminate all of the artifacts. In areas where the only available DEM is produced by older methods, then "striping" may still occur.

n-Type Azaacenes Containing B←N Units.

Science.gov (United States)

Min, Yang; Dou, Chuandong; Tian, Hongkun; Geng, Yanhou; Liu, Jun; Wang, Lixiang

2018-02-12

We disclose a novel strategy to design n-type acenes through the introduction of boron-nitrogen coordination bonds (B←N). We synthesized two azaacenes composed of two B←N units and six/eight linearly annelated rings. The B←N unit significantly perturbed the electronic structures of the azaacenes: Unique LUMOs delocalized over the entire acene skeletons and decreased aromaticity of the B←N-adjacent rings. Most importantly, these B←N-containing azaacenes exhibited low-lying LUMO energy levels and high electron affinities, thus leading to n-type character. The solution-processed organic field-effect transistor based on one such azaacene exhibited unipolar n-type characteristics with an electron mobility of 0.21 cm 2  V -1  s -1 . © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Elevator-related injuries to older adults in the United States, 1990 to 2006.

Science.gov (United States)

Steele, Gregory K; O'Neil, Joseph; Huisingh, Carrie; Smith, Gary A

2010-01-01

Elevators remain one of the safest forms of transportation; however, they are still associated with deaths and injuries. This study describes the epidemiology of elevator-related injuries among adults aged 65 years and older in the United States between 1990 and 2006, through a retrospective analysis of data from the National Electronic Injury Surveillance System of the U.S. Consumer Product Safety Commission. Proportions with 95% confidence intervals were calculated by age group for cause of injury, injured body region, injury type, and locale. Rate ratios with 95% confidence interval were calculated to determine any association between the body region injured, type of injury, and cause of injury categories. There were an estimated 44,870 elevator-related injuries in older adults. The mean age was 79.5 years, and approximately 75% were women. More than half of the injuries (51.4%) were caused from a slip, trip, or fall. Soft-tissue injuries were the most common injury type (48.0%). The upper extremities were the most commonly injured body region (26.2%). Almost 15% (14.5%) of those injured required hospital admission. Of those admitted, more than 40% were for a fractured hip. Injuries associated with passenger elevators occur fairly frequently among older adults, are often associated with slip, trip or falls, and can be severe enough to require hospital admission. Older adults should use caution when stepping on or off an elevator. Awareness of the risk and the circumstances leading to falls allows for better direction of intervention strategies.

Superfund record of decision (EPA Region 3), Westinghouse Elevator Company Plant, Operable Unit 2, Cumberland Township, Adams County, Gettysburg, PA, March 31, 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-04-01

This Record of Decision (ROD) presents the selected remedial action for Operable Unit 2 (Soils) at the Westinghouse Elevator Company Plant Site in Adams County, Pennsylvania. The selected remedy for the soils at the Westinghouse Elevator Plant is No Additional Action for this Operable Unit. The other alternatives evaluated would produce little or no environmental benefit at substantial cost.

Reliability assessment of Indian Point Unit 3 containment structure

International Nuclear Information System (INIS)

Kawakami, J.; Hwang, H.; Chang, M.T.; Reich, M.

1984-01-01

In the current design criteria, the load combinations specified for design of concrete containment structures are in the deterministic formats. However, by applying the probability-based reliability method developed by BNL to the concrete containment structures designed according to the criteria, it is possible to evaluate the reliability levels implied in the current design criteria. For this purpose, the reliability analysis is applied to the Indian Point Unit No. 3 containment. The details of the containment structure such as the geometries and the rebar arrangements, etc., are taken from the working drawings and the final safety analysis reports. Three kinds of loads are considered in the reliability analysis. They are, dead load (D), accidental pressure due to a large LOCA (P), and earthquake ground acceleration (E). Reliability analysis of the containment subjected to all combinations of loads is performed. Results are presented in this report

78 FR 9720 - Agency Information Collection Activities: Holders or Containers Which Enter the United States...

Science.gov (United States)

2013-02-11

... Activities: Holders or Containers Which Enter the United States Duty Free AGENCY: U.S. Customs and Border... or Containers which enter the United States Duty Free. This is a proposed extension of an information..., or other technological techniques or other forms of information. Title: Holders or Containers which...

Reliability assessment of Indian Point Unit 3 containment structure under combined loads

International Nuclear Information System (INIS)

Hwang, H.; Shinozuka, M.; Kawakami, J.; Reich, M.

1984-01-01

In the current design criteria, the load combinations specified for design of concrete containment structures are in the deterministic format. However, by applying the probability-based reliability analysis method developed by BNL to the concrete containment structures designed according to the criteria, it is possible to evaluate the reliability levels implied in the current design criteria. For this purpose, the reliability analysis is applied to the Indian Point Unit No. 3 containment. The details of the containment structure such as the geometries and the rebar arrangements, etc., are taken from the working drawings and the Final Safety Analysis Report. Three kinds of loads are considered in the reliability analysis. They are, dead load, accidental pressure due to a large LOCA, and earthquake ground acceleration. This paper presents the reliability analysis results of the Indian Point Unit 3 containment subjected to all combinations of loads

Sampling and decontamination plan for the Transuranic Storage Area--1/-R container storage unit

International Nuclear Information System (INIS)

Barry, G.A.

1992-11-01

This document describes the sampling and decontamination of the Transuranic Storage Area (TSA)-l/-R container storage area and the earthen-covered portion of the TSA-2 container storage unit at the Radioactive Waste Management Complex. Stored containers from the earthen-covered asphalt pads will be retrieved from the TSA-l/-R and TSA-2 container storage units. Container retrieval will be conducted under the TSA retrieval enclosure, a fabricated steel building to be constructed over the earthen-covered pad to provide containment and weather protection. Following container retrieval, the TSA retrieval enclosure will be decontaminated to remove radioactive and hazardous contamination. The underlying soils will be sampled and analyzed to determine whether any contaminated soils require removal

Pickering unit 1 containment leakage characterization

International Nuclear Information System (INIS)

Zakaib, G.D.

1994-01-01

Results of the design pressure test carried out on Pickering Reactor Building number 1 during late 1992 showed that the leakage rate of the building was close to the safety analysis value of 2.7% contained mass per hour at the design pressure of 41.4 kPa(g) and was significantly higher than that reported after the previous test conducted in the spring of 1987. This unexpected finding initiated the longest and the most comprehensive containment leakage investigation ever undertaken by Ontario Hydro. A thorough investigation of leakage behaviour by repeated testing, inspections, leak search and analysis was launched. The extensive leak search effort included items such as: leak source detection by soap solution application, use of ultrasonic detectors, fogging and tracer gas techniques, systematic systems isolation, thermal imaging of the exterior, and quantification of leak sites by flowmeter and bagging. Using a specially designed volumetric technique, the root cause of the problem was finally confirmed as being due to 'pressure dependent laminar leakage' through the hairline cracks in the dome concrete. Structural analysis indicated that the thermal gradients and pressure loading combined to cause the cracking early in the structure's operating history and that overall structural integrity has not been compromised. Leakage rate analysis using a new fluid mechanics model augmented by the effect of thermal strains indicated that the leakage could be significantly less under certain transient temperature gradient conditions. Several options for repairing the dome were considered by a multidisciplinary team and it was finally decided to apply a specially engineered multilayer elastomeric coating to the exterior concrete surface. When the unit was re-tested in October 1993, a dramatic ten-fold improvement in leakage rate (down to 0.25%/h at design pressure) was observed. This is lower than even the commissioning results and comparable to the performance of newer units

Preempting the pathogen: Blister rust and proactive management of high-elevation pines

Science.gov (United States)

Sue Miller; Anna Schoettle; Kelly Burns; Richard Sniezko; Patty Champ

2017-01-01

White pine blister rust has been spreading through western forests since 1910, causing widespread mortality in a group that includes some of the oldest and highest-elevation pines in the United States. The disease has recently reached Colorado and is expected to travel through the southern Rockies. Although it cannot be contained, RMRS researchers and collaborators are...

Transuranic Storage Area (TSA)-3 container storage unit RCRA closure plan

International Nuclear Information System (INIS)

Barry, G.A.; Lodman, D.L.; Spry, M.J.; Poor, K.J.

1992-11-01

This document describes the proposed plan for closure of the Transuranic Storage Area (TSA)-3 container storage unit at the Idaho National Engineering Laboratory in accordance with the Resource Conservation and Recovery Act closure requirements. The location, size, capacity, history, and current status of the unit are described. The unit will be closed by decontaminating structures and equipment that may have contacted waste. Sufficient sampling and documentation of all activities will be performed to demonstrate clean closure. A tentative schedule is provided in the form of a milestone chart

Exposure rates from concrete covered cylindrical units containing radioactive waste

International Nuclear Information System (INIS)

Hedemann Jensen, P.

1983-03-01

Exposure rates from cylindrical waste units containing the nuclides 60 Co, 134 Cs and 137 Cs homogeneously mixed in a solidification product have been calculated. Analyses have been made for single drums and for two disposal geometries, one with the units placed below ground near the surface in a circular geometry, and one with the units placed on the ground in a pile behind a concrete wall. Due to self-shielding of the units, the exposure rate from the two geometries will be a factor of only 10 - 20 higher than from a single unit, even without soil or wall shielding. With one meter of soil above the circular pile below ground, a reduction factor of 5.10 3 to 5.10 4 can be achieved, depending on the nuclide considered. Placing a one-meter concrete wall in front of the drum pile on the ground gives rise to a reduction factor in the range of 5.10 5 to 2.10 7 . (author)

Attributes for NHDplus Catchments (Version 1.1) for the Conterminous United States: Population Density, 2000

Science.gov (United States)

Wieczorek, Michael; LaMottem, Andrew E.

2010-01-01

This data set represents the average population density, in number of people per square kilometer multiplied by 10 for the year 2000, compiled for every catchment of NHDPlus for the conterminous United States. The source data set is the 2000 Population Density by Block Group for the Conterminous United States (Hitt, 2003). The NHDPlus Version 1.1 is an integrated suite of application-ready geospatial datasets that incorporates many of the best features of the National Hydrography Dataset (NHD) and the National Elevation Dataset (NED). The NHDPlus includes a stream network (based on the 1:100,00-scale NHD), improved networking, naming, and value-added attributes (VAAs). NHDPlus also includes elevation-derived catchments (drainage areas) produced using a drainage enforcement technique first widely used in New England, and thus referred to as "the New England Method." This technique involves "burning in" the 1:100,000-scale NHD and when available building "walls" using the National Watershed Boundary Dataset (WBD). The resulting modified digital elevation model (HydroDEM) is used to produce hydrologic derivatives that agree with the NHD and WBD. Over the past two years, an interdisciplinary team from the U.S. Geological Survey (USGS), and the U.S. Environmental Protection Agency (USEPA), and contractors, found that this method produces the best quality NHD catchments using an automated process (USEPA, 2007). The NHDPlus dataset is organized by 18 Production Units that cover the conterminous United States. The NHDPlus version 1.1 data are grouped by the U.S. Geologic Survey's Major River Basins (MRBs, Crawford and others, 2006). MRB1, covering the New England and Mid-Atlantic River basins, contains NHDPlus Production Units 1 and 2. MRB2, covering the South Atlantic-Gulf and Tennessee River basins, contains NHDPlus Production Units 3 and 6. MRB3, covering the Great Lakes, Ohio, Upper Mississippi, and Souris-Red-Rainy River basins, contains NHDPlus Production Units 4, 5

A regulatory view of containment integrity in the United Kingdom

International Nuclear Information System (INIS)

Bradford, P.M.; Patchett, C.M.

1994-01-01

This paper reviews the approach of HM Nuclear Installations Inspectorate (NII) to containment integrity in the United Kingdom (UK). NII is that part of the regulatory authority, the Health and Safety Executive (HSE), which administers the UK's nuclear site licensing system. A major part of the licensing process lies in the assessment of licensees' submissions for new and existing plant. The purpose of this paper is to: briefly review our revised Safety Assessment Principles, describe our assessment and inspection activities on the primary containment building of the Sizewell B PWR which is progressing to full power operation in 1994 and, to indicate our views on the possible directions for future research into containment design and performance. (author). 5 refs

Resonant frequencies in an elevated spherical container partially filled with water: FEM and measurement

Science.gov (United States)

Curadelli, O.; Ambrosini, D.; Mirasso, A.; Amani, M.

2010-01-01

In this paper, a numerical-experimental study of the overall dynamical response of elevated spherical tanks subjected to horizontal base motion is presented. The main objective is to gain insight in the physical response of this particular structural typology widely used in the petrochemical industry as liquefied petroleum gas (LPG) containers. In order to identify the natural frequencies of the modes that mainly contribute to the response, experimental free vibration tests on an elevated spherical tank model for different liquid levels were carried out. Next, a numerical model that takes into account the coupling between fluid and structure was developed and validated against the experimental results. A very good agreement between experimental and numerical results was obtained. The results obtained show the influence of liquid levels on natural frequencies and indicate that the sloshing has a significant effect on the dynamical characteristics of the analyzed system. In order to obtain a good representation of the overall dynamical behaviour of the system by means of a simplified lumped mass model, a minimum of three masses is suggested. Finally, appropriate names of these three masses are proposed in the present paper.

Self-Contained Portable Data Acquisition/Control System Unit for Hydrogen Environments

Data.gov (United States)

National Aeronautics and Space Administration — The platform is designed to be a self-contained unit that is built to support a wide variety of electrical equipment, and constructed so that it can be safely...

A regulatory view of containment integrity in the United Kingdom

Energy Technology Data Exchange (ETDEWEB)

Bradford, P M; Patchett, C M [Health and Safety Executive, Bootle (United Kingdom). Nuclear Installations Inspectorate

1994-12-31

This paper reviews the approach of HM Nuclear Installations Inspectorate (NII) to containment integrity in the United Kingdom (UK). NII is that part of the regulatory authority, the Health and Safety Executive (HSE), which administers the UK`s nuclear site licensing system. A major part of the licensing process lies in the assessment of licensees` submissions for new and existing plant. The purpose of this paper is to: briefly review our revised Safety Assessment Principles, describe our assessment and inspection activities on the primary containment building of the Sizewell B PWR which is progressing to full power operation in 1994 and, to indicate our views on the possible directions for future research into containment design and performance. (author). 5 refs.

Predictors of backrest elevation in critical care.

Science.gov (United States)

Grap, Mary Jo; Munro, Cindy L; Bryant, Sandra; Ashtiani, Brooke

2003-04-01

Low backrest and supine positions are associated with increased mortality and ventilator associated pneumonia (VAP). Data are not available across ICU settings about the level of backrest position used and its relationship to enteral feeding and hemodynamic status. The purpose of this descriptive study was to document the level of backrest elevation and position and identify factors associated with and predict positioning in a medical, surgical and neuroscience intensive care unit. Data were collected randomly in each unit over a 6-week period, resulting in 506 observations for170 patients. Backrest elevation was determined by electronic bed read-out or bed frame elevation gauge. BP, HR and enteral feeding status were retrieved from the medical record. Results showed that mean backrest elevation was 19.2 degrees and 70% of subjects were supine. No difference in backrest elevation among units was found. Significant correlations between backrest elevation and systolic BP (r=0.15, P=0.006); and backrest and diastolic BP (r=0.13, P=0.02) were found. There was no difference in backrest elevation between patients being fed and not being fed. Differences in backrest elevation for intubated versus nonintubated patients approached significance (P=0.07) with intubated patients at lower backrest elevations. In summary, use of higher backrest elevations (>30 degrees ) is minimal, is not related to feeding and minimally related to hemodynamic status. Strategies to meet published recommendations for backrest elevation (30-45 degrees ) must include repeated feedback about nurse's use of backrest elevation and estimates of elevation.

Attributes for NHDPlus Catchments (Version 1.1) for the Conterminous United States: Physiographic Provinces

Science.gov (United States)

Wieczorek, Michael; LaMotte, Andrew E.

2010-01-01

This dataset represents the area of each physiographic province (Fenneman and Johnson, 1946) in square meters, compiled for every catchment of NHDPlus for the conterminous United States. The source data are from Fenneman and Johnson's Physiographic Provinces of the United States, which is based on 8 major divisions, 25 provinces, and 86 sections representing distinctive areas having common topography, rock type and structure, and geologic and geomorphic history (Fenneman and Johnson, 1946). The NHDPlus Version 1.1 is an integrated suite of application-ready geospatial datasets that incorporates many of the best features of the National Hydrography Dataset (NHD) and the National Elevation Dataset (NED). The NHDPlus includes a stream network (based on the 1:100,00-scale NHD), improved networking, naming, and value-added attributes (VAAs). NHDPlus also includes elevation-derived catchments (drainage areas) produced using a drainage enforcement technique first widely used in New England, and thus referred to as "the New England Method." This technique involves "burning in" the 1:100,000-scale NHD and when available building "walls" using the National Watershed Boundary Dataset (WBD). The resulting modified digital elevation model (HydroDEM) is used to produce hydrologic derivatives that agree with the NHD and WBD. Over the past two years, an interdisciplinary team from the U.S. Geological Survey (USGS), and the U.S. Environmental Protection Agency (USEPA), and contractors, found that this method produces the best quality NHD catchments using an automated process (USEPA, 2007). The NHDPlus dataset is organized by 18 Production Units that cover the conterminous United States. The NHDPlus version 1.1 data are grouped by the U.S. Geologic Survey's Major River Basins (MRBs, Crawford and others, 2006). MRB1, covering the New England and Mid-Atlantic River basins, contains NHDPlus Production Units 1 and 2. MRB2, covering the South Atlantic-Gulf and Tennessee River basins

Convergent Synthesis of Rigid Macrocycles Containing One and Two Tetrathiafulvalene Units

DEFF Research Database (Denmark)

Simonsen, Klaus B.; Thorup, Niels; Becher, Jan

1997-01-01

The synthesis of rigid tetrathiafulvalenophanes containing one or two tetrathiafulvalene units is presented, together with a stepwise convergent synthesis of macrocyclic bis-tetrathiafulvalenes via several open dimeric tetrathiafulvalenes. These systems were investigated by cyclic voltammetry...... and by X-ray crystallography....

Feasibility of Shape-Memory Ni/Ti Alloy Wire Containing Tube Elevators for Transcrestal Detaching Maxillary Sinus Mucosa: Ex Vivo Study

Directory of Open Access Journals (Sweden)

Yanfeng Li

2016-12-01

Full Text Available Background: Osteotome sinus floor elevation is a less invasive approach to augment an insufficient alveolar bone at the posterior maxilla for dental implantation. However, this approach has some limitations due to the lack of sinus lift tools available for clinical use and the small transcrestal access to the maxillary sinus floor. We recently invented shape-memory Ni/Ti alloy wire containing tube elevators for transcrestal detaching maxillary sinus mucosa, and developed goat ex vivo models for direct visualizing the effectiveness of detaching sinus mucosa in real time during transcrestal maxillary sinus floor elevation. Methods: We evaluated our invented elevators, namely elevator 012 and elevator 014, for their effectiveness for transcrestal detaching maxillary sinus mucosa using the goat ex vivo models. We measured the length of sinus mucosa detached in mesial and distal directions or buccal and palatal directions, and the space volume created by detaching maxillary sinus mucosa in mesial, distal, buccal and palatal directions using the invented elevators. Results: Elevator 012 had a shape-memory Ni/Ti alloy wire with a diameter of 0.012 inch, while elevator 014 had its shape-memory Ni/Ti alloy wire with a diameter of 0.014 inch. Elevator 012 could detach the goat maxillary sinus mucosa in the mesial or distal direction for 12.1±4.3 mm, while in the buccal or palatal direction for 12.5±6.7 mm. The elevator 014 could detach the goat maxillary sinus mucosa for 23.0±4.9 mm in the mesial or distal direction, and for 19.0±8.1 mm in the buccal or palatal direction. An average space volume of 1.7936±0.2079 ml was created after detaching the goat maxillay sinus mucosa in both mesial/distal direction and buccal/palatal direction using elevator 012; while the average space volume created using elevator 014 was 1.8764±0.2366 ml. Conclusion: Both two newly invented tube elevators could effectively detach the maxillary sinus mucosa on the goat ex

Feasibility of Shape-Memory Ni/Ti Alloy Wire Containing Tube Elevators for Transcrestal Detaching Maxillary Sinus Mucosa: Ex Vivo Study.

Science.gov (United States)

Li, Yanfeng; Wang, Fuli; Hu, Pin; Fan, Jiadong; Han, Yishi; Liu, Bin; Liu, Tao; Yang, Chunhao; Gu, Xiangmin

2016-01-01

Osteotome sinus floor elevation is a less invasive approach to augment an insufficient alveolar bone at the posterior maxilla for dental implantation. However, this approach has some limitations due to the lack of sinus lift tools available for clinical use and the small transcrestal access to the maxillary sinus floor. We recently invented shape-memory Ni/Ti alloy wire containing tube elevators for transcrestal detaching maxillary sinus mucosa, and developed goat ex vivo models for direct visualizing the effectiveness of detaching sinus mucosa in real time during transcrestal maxillary sinus floor elevation. We evaluated our invented elevators, namely elevator 012 and elevator 014, for their effectiveness for transcrestal detaching maxillary sinus mucosa using the goat ex vivo models. We measured the length of sinus mucosa detached in mesial and distal directions or buccal and palatal directions, and the space volume created by detaching maxillary sinus mucosa in mesial, distal, buccal and palatal directions using the invented elevators. Elevator 012 had a shape-memory Ni/Ti alloy wire with a diameter of 0.012 inch, while elevator 014 had its shape-memory Ni/Ti alloy wire with a diameter of 0.014 inch. Elevator 012 could detach the goat maxillary sinus mucosa in the mesial or distal direction for 12.1±4.3 mm, while in the buccal or palatal direction for 12.5±6.7 mm. The elevator 014 could detach the goat maxillary sinus mucosa for 23.0±4.9 mm in the mesial or distal direction, and for 19.0±8.1 mm in the buccal or palatal direction. An average space volume of 1.7936±0.2079 ml was created after detaching the goat maxillay sinus mucosa in both mesial/distal direction and buccal/palatal direction using elevator 012; while the average space volume created using elevator 014 was 1.8764±0.2366 ml. Both two newly invented tube elevators could effectively detach the maxillary sinus mucosa on the goat ex vivo sinus models. Moreover, elevator 014 has advantages over

Failure Mode Estimation of Wolsong Unit 1 Containment Building with respect to Severe Accident Condition

International Nuclear Information System (INIS)

Hahm, Dae Gi; Choi, In Kil

2009-01-01

The containment buildings in a nuclear power plant (NPP) are final barriers against the exposure of harmful radiation materials at severe accident condition. Since the accident at Three Mile Island nuclear plant in 1979, it has become necessary to evaluate the internal pressure capacity of the containment buildings for the assessment of the safety of nuclear power plants. According to this necessity, many researchers including Yonezawa et al. and Hu and Lin analyzed the ultimate capacity of prestressed concrete containments subjected to internal pressure which can be occurred at sever accident condition. Especially in Wolsong nuclear power plant, the Unit 1 containment structures were constructed in the late 1970 to early 1980, so that the end of its service life will be reached in near future. Since that the complete decommission and reconstruction of the NPP may cause a huge expenses, an extension of the service time can be a cost-effective alternative. To extend the service time of NPP, an overall safety evaluation of the containment building under severe accident condition should be performed. In this study, we assessed the pressure capacity of Wolsong Unit 1 containment building under severe accident, and estimated the responses at all of the probable critical areas. Based on those results, we found the significant failure modes of Wolsong Unit 1 containment building with respect to the severe accident condition. On the other hand, for the aged NPP, the degradation of their structural performance must also be explained in the procedure of the internal pressure capacity evaluation. Therefore, in this study, we performed a parametric study on the degradation effects and evaluated the internal pressure capacity of Wolsong Unit 1 containment building with considering aging and degradation effects

Attributes for NHDPlus catchments (Version 1.1) for the conterminous United States: STATSGO soil characteristics

Science.gov (United States)

Wieczorek, Michael; LaMotte, Andrew E.

2010-01-01

This data set represents estimated soil variables compiled for every catchment of NHDPlus for the conterminous United States. The variables included are cation exchange capacity, percent calcium carbonate, slope, water-table depth, soil thickness, hydrologic soil group, soil erodibility (k-factor), permeability, average water capacity, bulk density, percent organic material, percent clay, percent sand, and percent silt. The source data set is the State Soil ( STATSGO ) Geographic Database (Wolock, 1997). The NHDPlus Version 1.1 is an integrated suite of application-ready geospatial datasets that incorporates many of the best features of the National Hydrography Dataset (NHD) and the National Elevation Dataset (NED). The NHDPlus includes a stream network (based on the 1:100,00-scale NHD), improved networking, naming, and value-added attributes (VAAs). NHDPlus also includes elevation-derived catchments (drainage areas) produced using a drainage enforcement technique first widely used in New England, and thus referred to as "the New England Method." This technique involves "burning in" the 1:100,000-scale NHD and when available building "walls" using the National Watershed Boundary Dataset (WBD). The resulting modified digital elevation model (HydroDEM) is used to produce hydrologic derivatives that agree with the NHD and WBD. Over the past two years, an interdisciplinary team from the U.S. Geological Survey (USGS), and the U.S. Environmental Protection Agency (USEPA), and contractors, found that this method produces the best quality NHD catchments using an automated process (USEPA, 2007). The NHDPlus dataset is organized by 18 Production Units that cover the conterminous United States. The NHDPlus version 1.1 data are grouped by the U.S. Geologic Survey's Major River Basins (MRBs, Crawford and others, 2006). MRB1, covering the New England and Mid-Atlantic River basins, contains NHDPlus Production Units 1 and 2. MRB2, covering the South Atlantic-Gulf and Tennessee

Impact of mobile intensive care unit use on total ischemic time and clinical outcomes in ST-elevation myocardial infarction patients - real-world data from the Acute Coronary Syndrome Israeli Survey.

Science.gov (United States)

Koifman, Edward; Beigel, Roy; Iakobishvili, Zaza; Shlomo, Nir; Biton, Yitschak; Sabbag, Avi; Asher, Elad; Atar, Shaul; Gottlieb, Shmuel; Alcalai, Ronny; Zahger, Doron; Segev, Amit; Goldenberg, Ilan; Strugo, Rafael; Matetzky, Shlomi

2017-01-01

Ischemic time has prognostic importance in ST-elevation myocardial infarction patients. Mobile intensive care unit use can reduce components of total ischemic time by appropriate triage of ST-elevation myocardial infarction patients. Data from the Acute Coronary Survey in Israel registry 2000-2010 were analyzed to evaluate factors associated with mobile intensive care unit use and its impact on total ischemic time and patient outcomes. The study comprised 5474 ST-elevation myocardial infarction patients enrolled in the Acute Coronary Survey in Israel registry, of whom 46% ( n=2538) arrived via mobile intensive care units. There was a significant increase in rates of mobile intensive care unit utilization from 36% in 2000 to over 50% in 2010 ( pcare unit use were Killip>1 (odds ratio=1.32, pcare units benefitted from increased rates of primary reperfusion therapy (odds ratio=1.58, pcare unit benefitted from shorter median total ischemic time compared with non-mobile intensive care unit patients (175 (interquartile range 120-262) vs 195 (interquartile range 130-333) min, respectively ( pcare unit use was the most important predictor in achieving door-to-balloon time care unit group (odds ratio=0.79, 95% confidence interval (0.66-0.94), p=0.01). Among patients with ST-elevation myocardial infarction, the utilization of mobile intensive care units is associated with increased rates of primary reperfusion, a reduction in the time interval to reperfusion, and a reduction in one-year adjusted mortality.

Elevated CO[sub 2] alters deployment of roots in small growth containers

Energy Technology Data Exchange (ETDEWEB)

Berntson, G M; McConnaughay, K D.M.; Bazzaz, F A [Harvard University, Cambridge, MA (United States). Dept. of Organismic and Evolutionary Biology

1993-07-01

Previously the authors examined how limited rooting space and nutrient supply influenced plant growth under elevated atmospheric CO[sub 2] concentrations. To gain insight into how elevated CO[sub 2] atmospheres affect how plants utilize available belowground space, when rooting space and nutrient supply are limited, they measured the deployment of roots within pots through time. Contrary to aboveground responses, patterns of belowground deployment were most strongly influenced by elevated CO[sub 2] in pots of different volume and shape. Further, elevated CO[sub 2] conditions interacted differently with limited belowground space for the two species studied, Abutilon theophrasti, a C[sub 3] dicot with a deep taproot, and Setaria faberii, a C4 monocot with a shallow fibrous root system. For Setaria, elevated CO[sub 2] increased the size of the largest region of low root density at the pot surface in larger rooting volumes independent of nutrient content, thereby decreasing their efficiency of deployment. For Abutilon, plants responded to elevated CO[sub 2] concentrations by equalizing the pattern of deployment in all the pots. Nutrient concentration, and not pot size or shape, greatly influenced the density of root growth. Root densities for Abutilon and Setaria were similar to those observed in field conditions, for annual dicots and monocots respectively, suggesting that studies using pots may successfully mimic natural conditions.

Heat Transfer Reactor Experiment (HTRE)-3 Container Storage Unit Resource Conservation Recovery Act closure plan

International Nuclear Information System (INIS)

Spry, M.J.

1992-11-01

This document describes the closure of the HTRE-3 Container Storage Unit under the requirements of the Resource Conservation and Recovery Act. The unit's location, size, history, and current status are described. The document also summarizes the decontamination and decommissioning efforts performed in 1983 and provides an estimate of,waste residues remaining in the HTRE-3 assembly. A risk evaluation was performed that demonstrates that the residue does not pose a hazard to public health or the environment. Based on the risk evaluation, it is proposed that the HTRE-3 Container Storage Unit be closed in its present condition, without further decontamination or removal activities

INEL Operable Unit 7-13 containment and stabilization configuration option

International Nuclear Information System (INIS)

Raivo, B.D.; Richardson, J.G.; Nickelson, D.F.

1993-05-01

A containment and stabilization configuration option has been developed for the Idaho National Engineering Laboratory's Subsurface Disposal Area Operable Unit 7-13, the transuranic (TRU)-contaminated waste pits and trenches. The configuration option is presented as an end-to-end system block diagram. Functional subelements are separately discussed, and technical background information, assumptions, input, high-level subelement requirements, and output are presented for each option

Quick look report, entry 4: Three Mile Island Unit 2, November 13, 1980

International Nuclear Information System (INIS)

Eidam, G.E.

1981-06-01

This report summarizes tasks performed during entry 4 at Three Mile Island Unit 2. During the entry into containment, which was made on November 13, 1980, additional beta and gamma surveys were conducted to supplement data acquired on previous entries. A decontamination test was completed on Elevation 305. Power receptables tested on Elevation 305 were deenergized, but receptacles on Elevation 347 were energized. Still photography was acquired of Elevations 305 and 347. During the entry, 86 still photographs were taken. Videotaping (color and black and white) was done on Elevations 305 and 347, but lighting on both elevations was insufficient for high-quality video

Preservice and inservice requirements for containment structures in the United States - a status report

International Nuclear Information System (INIS)

Sammataro, R.F.

1987-01-01

Assuring the lifetime integrity of containment structures for nuclear power plants is becoming increasingly important as existing design criteria are reexamined, as new requirements for containment inspection and testing are formulated, and as today's operating nuclear plants are growing older. Section XI of the ASME Code contains separate rules for metal (Class MC) and concrete (Class CC) containments. Requirements for Class MC containments have been published in Subsection IWE, Requirements for Class MC Components of Light-Water Cooled Power Plants, of Section XI. Rules for Class CC containments are currently being developed and will be published in Subsection IWL, Requirements for Class CC Components of Light-Water Cooled Power Plants, of Section XI. First published in 1981, Subsection IWE has been adopted by a number of state jurisdictions in the United States and is presently being reviewed by the United States Nuclear Regulatory Commission. Federal regulations that will require mandatory compliance by nuclear plant owners are forthcoming. When implemented, the requirements in Subsection IWE and Subsection IWL will provide a reasonable and systematic basis for assuring the integrity of metal and concrete containment structures during their service lifetime. This paper presents an overview of the preservice and inservice requirements for containment structures in Section XI of the ASME Code with consideration of the practical factors that should accompany user compliance. (orig./GL)

Study on the Novel Dicyanate Ester Resin Containing Naphthalene Unit

Institute of Scientific and Technical Information of China (English)

Hong Qiang YAN; Hong Yun PENG; Li JI; Guo Rong QI

2004-01-01

The novel dicyanate ester resin containing naphthalene unit (DNCY) was synthesized, and characterized by FT-IR, 1H-NMR, 13C-NMR and elemental analysis (EA).The thermal properties of DNCY resin was studied by thermal degradation analysis at a heating rate of 10 (C /min-1 in N2 and air. The DNCY resin exhibited better thermal and thermal-oxidative stability than bisphenol A dicyanate (BACY) resin.

Analysis of heavy-rain-producing elevated thunderstorms in the MO-KS-OK region of the United States

Science.gov (United States)

McCoy, Laurel

Most elevated thunderstorms in the United States occur in the Midwest, with a maximum in eastern Kansas (Colman 1990a). Elevated thunderstorms are defined as thunderstorms that occur over a very stable surface boundary layer (Colman 1990b). They may be better defined as convection occurring over a stable layer near the surface, essentially cut off from surface-based instability (Corfidi et al. 2006). Elevated mesoscale convective systems produce 30-70% of the total rainfall during the warm season over the Central Plains (Moore et al. 2003). 1.1 Purpose Elevated thunderstorms are still not very well understood. Elevated convection can take a variety of forms, and can be very similar to surface-based convection. Corfidi et al. (2006) describe the challenge of finding the originating layer of parcels making up a convective cloud. Surface-based convection often incorporates elevated parcels, and elevated convection can bring surface parcels into its updraft. The distinction between the two types of storms can be defined by where most of the parcels originate. This becomes especially hard to distinguish as convection transitions from surface-based to elevated and vice-versa (Corfidi et al. 2006). Colman (1990a), in his study, used three criteria to delineate elevated thunderstorm station reports from surface-based thunderstorm station reports: 1) The observation must lie on the cold side of an analyzed front that shows a clear contrast in temperature, dew-point temperature, and wind. 2) The station's wind, temperature, and dew-point temperature must be qualitatively similar to the immediately surrounding values. 3) The surface air on the warm side of the analyzed front must have a higher equivalent potential temperature (thetae) than the air on the cold side of the front (Colman 1990a). These three criteria have been incorporated into several studies since for the evaluation of elevated convection (e.g., Grant 1995; Rochette and Moore 1996; Moore et al. 1998; Moore et

Attributes for NHDPlus Catchments (Version 1.1) for the Conterminous United States: Mean Annual R-factor, 1971-2000

Science.gov (United States)

Wieczorek, Michael; LaMotte, Andrew E.

2010-01-01

This data set represents the average annual R-factor, rainfall-runoff erosivity measure, compiled for every catchment of NHDPlus for the conterminous United States. The source data are from Christopher Daly of the Spatial Climate Analysis Service, Oregon State University, and George Taylor of the Oregon Climate Service, Oregon State University (2002), who developed spatially distributed estimates of R-factor for the period 1971-2000 for the conterminous United States. The NHDPlus Version 1.1 is an integrated suite of application-ready geospatial datasets that incorporates many of the best features of the National Hydrography Dataset (NHD) and the National Elevation Dataset (NED). The NHDPlus includes a stream network (based on the 1:100,00-scale NHD), improved networking, naming, and value-added attributes (VAAs). NHDPlus also includes elevation-derived catchments (drainage areas) produced using a drainage enforcement technique first widely used in New England, and thus referred to as "the New England Method." This technique involves "burning in" the 1:100,000-scale NHD and when available building "walls" using the National Watershed Boundary Dataset (WBD). The resulting modified digital elevation model (HydroDEM) is used to produce hydrologic derivatives that agree with the NHD and WBD. Over the past two years, an interdisciplinary team from the U.S. Geological Survey (USGS), and the U.S. Environmental Protection Agency (USEPA), and contractors, found that this method produces the best quality NHD catchments using an automated process (USEPA, 2007). The NHDPlus dataset is organized by 18 Production Units that cover the conterminous United States. The NHDPlus version 1.1 data are grouped by the U.S. Geologic Survey's Major River Basins (MRBs, Crawford and others, 2006). MRB1, covering the New England and Mid-Atlantic River basins, contains NHDPlus Production Units 1 and 2. MRB2, covering the South Atlantic-Gulf and Tennessee River basins, contains NHDPlus

Transuranic Storage Area (TSA)-2 container storage unit RCRA closure plan

International Nuclear Information System (INIS)

Lodman, D.W.; Spry, M.J.; Nolte, E.P.; Barry, G.A.

1992-11-01

This document describes the proposed plans for closure of the Transuranic Storage Area (TSA)-2 container storage unit at the Idaho National Engineering Laboratory in accordance with the Resource Conservation and Recovery Act closure requirements. The location, size, capacity, history, and current status of the unit are described. Future plans for the unit include incorporating the earthen-covered portion of the TSA-2 pad into a TSA retrieval enclosure along with the TSA-1 and TSAR pads, and closure of the portion of the TSA-2 pad under the Air Support Weather Shield (ASWS-2). This plan addresses closure of the ASWS-2 by decontaminating structures and equipment that may have contacted the waste. Sufficient sampling and documentation of all closure activities will be performed to demonstrate clean closure. A tentative schedule is provided in the form of a milestone chart

Design loads, loading combinations and structural acceptance criteria for BWR containments in the United States

International Nuclear Information System (INIS)

Edwards, N.W.

1979-01-01

The definition of loads, loading combinations, and structural acceptance criteria used for the design and evaluation of BWR containments in the Unites States has become much more comprehensive over the past decade. The Mark I pressure suppression containment vessels were designed for a static design pressure, a design temperature, dead load and static equivalent earthquake. The current Mark III containments are being designed to accommodate many more loads such as safety relief valve discharge loads, and suppression pool hydrodynamic loadings associated with the steam condensation phenomena as well as pressure and temperature transients for a range of pipe break sizes. Consistent with the more comprehensive definition of loads and loading combinations, the ASME Code presently establishes structural acceptance criteria with different margins of safety by the definition of Service Level Assignments A, B, C and D. Acting in a responsible manner, United States utilities are currently evaluating and modifying existing containment vessels to account for the more detailed load definition and structural acceptance criteria. (orig.)

Integration optimisation of elevated pressure air separation unit with gas turbine in an IGCC power plant

International Nuclear Information System (INIS)

Han, Long; Deng, Guangyi; Li, Zheng; Wang, Qinhui; Ileleji, Klein E.

2017-01-01

Highlights: • IGCC thermodynamic model was setup carefully. • Simulations focus on integration between an elevated pressure ASU with gas turbine. • Different recommended solutions from those of low pressure ASUs are figured out. • Full N 2 injection and 80% air extraction was suggested as the optimum integration. - Abstract: The integration optimisation between an elevated pressure air separation unit (EP-ASU) and gas turbine is beneficial to promote net efficiency of an integrated gasification combined cycle (IGCC) power plant. This study sets up the thermodynamic model for a 400 MW plant specially coupled with an EP-ASU, aiming to examine system performances under different integrations and acquire the optimum solution. Influences of air extraction rate at conditions of without, partial and full N 2 injection, as well as the effects of N 2 injection rate when adopting separate ASU, partial and full integrated ASU were both analysed. Special attention has been paid to performance differences between utilising an EP-ASU and a low pressure unit. Results indicated that integration solution with a separate EP-ASU or without N 2 injection would not be reasonable. Among various recommended solutions for different integration conditions, N 2 injection rate increased with the growth of air extraction rate. The integration with an air extraction rate of 80% and full N 2 injection was suggested as the optimum solution. It is concluded that the optimum integration solution when adopting an EP-ASU is different from that using a low pressure one.

Reactor container

International Nuclear Information System (INIS)

Kojima, Yoshihiro; Hosomi, Kenji; Otonari, Jun-ichiro.

1997-01-01

In the present invention, a catalyst for oxidizing hydrogen to be disposed in a reactor container upon rupture of pipelines of a reactor primary coolant system is prevented from deposition of water droplets formed from a reactor container spray to suppress elevation of hydrogen concentration in the reactor container. Namely, a catalytic combustion gas concentration control system comprises a catalyst for oxidizing hydrogen and a support thereof. In addition, there is also disposed a water droplet deposition-preventing means for preventing deposition of water droplets in a reactor pressure vessel on the catalyst. Then, the effect of the catalyst upon catalytic oxidation reaction of hydrogen can be kept high. The local elevation of hydrogen concentration can be prevented even upon occurrence of such a phenomenon that various kinds of mobile forces in the container such as dry well cooling system are lost. (I.S.)

Centre-containing spiral-geometric structure of the space-time and nonrelativistic relativity of the unit time

International Nuclear Information System (INIS)

Shakhazizyan, S.R.

1987-01-01

The problem of nonrelativistic dependence of unit length and unit time on the position in the space is considered on the basis of centre-containing spiral-geometric structure of the space-time. The experimental results of variation of the unit time are analyzed which well agree with the requirements of the model proposed. 13 refs.; 12 figs

Impact of Site Elevation on Mg Smelter Design

Science.gov (United States)

Baker, Phillip W.

Site elevation has many surprising and significant impacts on the engineering design of metallurgical plant of all types. Electrolytic magnesium smelters maybe built at high elevation for a variety of reasons including availability of raw material, energy or electric power. Because of the unit processes they typically involve, Mg smelters can be extensively impacted by site elevation. In this paper, generic examples of the design changes required to adapt a smelter originally designed for sea level to operate at 2700 m are presented. While the examples are drawn from a magnesium plant design case, these changes are generically applicable to all industrial plants utilizing similar unit processes irrespective of product.

Two luminescent frameworks constructed from lead(II) salts with carboxylate ligands containing dinuclear lead(II) units

International Nuclear Information System (INIS)

Zhu Xiandong; Li Xiaoju; Liu Qingyan; Lue Jian; Guo Zhengang; He Jinrun; Li Yafeng; Cao Rong

2007-01-01

Two luminescent Pb(II) coordination frameworks containing dinuclear lead(II) units, [Pb(PYDC)(H 2 O)] n (1) and [Pb(HPHT)] n (2) have been prepared by the self-assembly of lead(II) salts with pyridinecarboxylate and benzenecarboxylate. Single-crystal X-ray diffraction analyses reveal that compound 1 is a three-dimensional architecture consisting of Pb 2 O 2 dimeric building units, whereas compound 2 is a two-dimensional layer structure containing one-dimensional lead-oxide chains. The luminescent properties of 1 and 2 have been investigated in the solid state at room temperature, indicating structure-dependent photoluminescent properties of the coordination frameworks. - Graphical abstract: Two luminescent Pb(II) coordination frameworks, [Pb(PYDC)(H 2 O)] n (1) and [Pb(HPHT)] n (2) have been prepared. Single-crystal analyses reveal that compound 1 is a three-dimensional architecture consisting of Pb 2 O 2 dimeric building units, whereas compound 2 is a two-dimensional layer structure containing one-dimensional lead-oxide chains. The luminescent properties have been investigated, indicating structure-dependent photoluminescent properties of the coordination frameworks

Analysis of loss of decay heat removal sequences at Browns Ferry Unit One: Chapter 17

International Nuclear Information System (INIS)

Harrington, R.M.

1983-01-01

This paper summarizes the Oak Ridge National Laboratory (ORNL) report ''Loss of DHR Sequences at Browns Ferry Unit One - Accident Sequence Analysis'' (NUREG/CR-2973). The Loss of DHR investigation is the third in a series of accident studies concerning the BWR 4 - MK I containment plant design. These studies, sponsored by the Nuclear Regulatory Commission Severe Accident Sequence Analysis (SASA) program, have been conducted at ORNL with the full cooperation of the Tennessee Valley Authority (TVA), using Unit One of the Browns Ferry Nuclear Plant as the model design. Each unit of this three-unit plant has a maximum authorized power of 3293 MW(t) or 1067 net MW(e). The primary containments are of the Mark I pressure suppression pool type and the three units share a secondary containment of the controlled leakage, elevated release design. Each unit occupies a separate reactor building located in one structure underneath the common refueling floor

Modelling and simulation of containment on full scope simulator for Qinshan 300 MW Nuclear Power Unit

International Nuclear Information System (INIS)

Zou Tingyun

1996-01-01

A multi-node containment thermal-hydraulic model has been developed and adapted in Full Scope Simulator for Qinshan 300 MW Nuclear Power Unit with good realtime simulation effects. Containment pressure for LBLOCA calculated by the model is well agreed with those of CONTEMPT-4/MOD3

Operation experience with elevated ammonia

International Nuclear Information System (INIS)

Vankova, Katerina; Kysela, Jan; Malac, Miroslav; Petrecky, Igor; Svarc, Vladimir

2011-01-01

The 10 VVER units in the Czech and Slovak Republics are all in very good water chemistry and radiation condition, yet questions have arisen regarding the optimization of cycle chemistry and improved operation in these units. To address these issues, a comprehensive experimental program for different water chemistries of the primary circuit was carried out at the Rez Nuclear Research Institute, Czech Republic, with the goal of judging the influence of various water chemistries on radiation build-up. Four types of water chemistries were compared: standard VVER water chemistry (in common use), direct hydrogen dosing without ammonia, standard VVER water chemistry with elevated ammonia levels, and zinc dosing to standard VVER water chemistry. The test results showed that the types of water chemistry other than the common one have benefits for the operation of the nuclear power plant (NPP) primary circuit. Operation experience with elevated ammonia at NPP Dukovany Units 3 and 4 is presented which validates the experimental results, demonstrating improved corrosion product volume activity. (orig.)

VALIDATION OF THE ASTER GLOBAL DIGITAL ELEVATION MODEL VERSION 2 OVER THE CONTERMINOUS UNITED STATES

Directory of Open Access Journals (Sweden)

D. Gesch

2012-07-01

Full Text Available The ASTER Global Digital Elevation Model Version 2 (GDEM v2 was evaluated over the conterminous United States in a manner similar to the validation conducted for the original GDEM Version 1 (v1 in 2009. The absolute vertical accuracy of GDEM v2 was calculated by comparison with more than 18,000 independent reference geodetic ground control points from the National Geodetic Survey. The root mean square error (RMSE measured for GDEM v2 is 8.68 meters. This compares with the RMSE of 9.34 meters for GDEM v1. Another important descriptor of vertical accuracy is the mean error, or bias, which indicates if a DEM has an overall vertical offset from true ground level. The GDEM v2 mean error of –0.20 meters is a significant improvement over the GDEM v1 mean error of –3.69 meters. The absolute vertical accuracy assessment results, both mean error and RMSE, were segmented by land cover to examine the effects of cover types on measured errors. The GDEM v2 mean errors by land cover class verify that the presence of aboveground features (tree canopies and built structures cause a positive elevation bias, as would be expected for an imaging system like ASTER. In open ground classes (little or no vegetation with significant aboveground height, GDEM v2 exhibits a negative bias on the order of 1 meter. GDEM v2 was also evaluated by differencing with the Shuttle Radar Topography Mission (SRTM dataset. In many forested areas, GDEM v2 has elevations that are higher in the canopy than SRTM.

Validation of the ASTER Global Digital Elevation Model Version 2 over the conterminous United States

Science.gov (United States)

Gesch, Dean B.; Oimoen, Michael J.; Zhang, Zheng; Meyer, David J.; Danielson, Jeffrey J.

2012-01-01

The ASTER Global Digital Elevation Model Version 2 (GDEM v2) was evaluated over the conterminous United States in a manner similar to the validation conducted for the original GDEM Version 1 (v1) in 2009. The absolute vertical accuracy of GDEM v2 was calculated by comparison with more than 18,000 independent reference geodetic ground control points from the National Geodetic Survey. The root mean square error (RMSE) measured for GDEM v2 is 8.68 meters. This compares with the RMSE of 9.34 meters for GDEM v1. Another important descriptor of vertical accuracy is the mean error, or bias, which indicates if a DEM has an overall vertical offset from true ground level. The GDEM v2 mean error of -0.20 meters is a significant improvement over the GDEM v1 mean error of -3.69 meters. The absolute vertical accuracy assessment results, both mean error and RMSE, were segmented by land cover to examine the effects of cover types on measured errors. The GDEM v2 mean errors by land cover class verify that the presence of aboveground features (tree canopies and built structures) cause a positive elevation bias, as would be expected for an imaging system like ASTER. In open ground classes (little or no vegetation with significant aboveground height), GDEM v2 exhibits a negative bias on the order of 1 meter. GDEM v2 was also evaluated by differencing with the Shuttle Radar Topography Mission (SRTM) dataset. In many forested areas, GDEM v2 has elevations that are higher in the canopy than SRTM.

Attributes for NHDPlus Catchments (Version 1.1) for the Conterminous United States: Normalized Atmospheric Deposition for 2002, Ammonium (NH4)

Science.gov (United States)

Wieczorek, Michael; LaMotte, Andrew E.

2010-01-01

This data set represents the average normalized atmospheric (wet) deposition, in kilograms, of Ammonium (NH4) for the year 2002 compiled for every catchment of NHDPlus for the conterminous United States. Estimates of NH4 deposition are based on National Atmospheric Deposition Program (NADP) measurements (B. Larsen, U.S. Geological Survey, written commun., 2007). De-trending methods applied to the year 2002 are described in Alexander and others, 2001. NADP site selection met the following criteria: stations must have records from 1995 to 2002 and have a minimum of 30 observations. The NHDPlus Version 1.1 is an integrated suite of application-ready geospatial datasets that incorporates many of the best features of the National Hydrography Dataset (NHD) and the National Elevation Dataset (NED). The NHDPlus includes a stream network (based on the 1:100,00-scale NHD), improved networking, naming, and value-added attributes (VAAs). NHDPlus also includes elevation-derived catchments (drainage areas) produced using a drainage enforcement technique first widely used in New England, and thus referred to as "the New England Method." This technique involves "burning in" the 1:100,000-scale NHD and when available building "walls" using the National Watershed Boundary Dataset (WBD). The resulting modified digital elevation model (HydroDEM) is used to produce hydrologic derivatives that agree with the NHD and WBD. Over the past two years, an interdisciplinary team from the U.S. Geological Survey (USGS), and the U.S. Environmental Protection Agency (USEPA), and contractors, found that this method produces the best quality NHD catchments using an automated process (USEPA, 2007). The NHDPlus dataset is organized by 18 Production Units that cover the conterminous United States. The NHDPlus version 1.1 data are grouped by the U.S. Geologic Survey's Major River Basins (MRBs, Crawford and others, 2006). MRB1, covering the New England and Mid-Atlantic River basins, contains NHDPlus

Chemistry experiences from a containment fire at Ringhals unit 2

International Nuclear Information System (INIS)

Arvidsson, Bengt; Svanberg, Pernilla; Bengtsson, Bernt

2012-09-01

At the refuelling outage in Ringhals unit 2, during an ongoing Containment Air Test (CAT), a fire event occurred at the refuelling deck/entrance floor. Due to the ongoing CAT with high pressure, all attempts to enter the containment to extinguish the fire were impossible. The fire started as a short circuit (spark) in a vacuum cleaner that was left in the containment by mistake and then set fire to nearby material. Approximate, 5 kg of rubber material and 30 kg of plastic material were estimated to have been burned out. The complete inside of the containment from the level of fire (+115) up to the ceiling/dome (+156) was colored black by soot. Soot or smoke was also spread throughout the whole containment building and the cavity/reactor vessel was contaminated by a minor part of soot due to some unsuccessful covering of the area during CAT. All fuel assemblies were stored in the fuel pool building and not affected by the fire. During the pressure reduction of containment, high air humidity with moisture precipitation occurred and caused a rapid general corrosion on steel surfaces due to high levels of chloride in the soot together with some pitting on stainless steel piping. Immediate action was to install portable dryers to lower the humidity, followed by the start of an extensive cleaning program with objectives to prevent plant degradation/recontamination of soot and bring the unit back in operation. More than 1300 people including >150 cleaners has been appointed to this project. All piping, insulation, cables, >4.500 components, 6.340 m 2 of concrete wall surface and 5.100 m 2 of concrete floor surface have been cleaned during 7 months to an estimated cost of 20 million Euro. Chemistry staff has been deeply involved in sampling and chemical analysis of contaminated surfaces/objects as well as establishing criteria's for cleaning equipment, procedures and specifications. Approximately 12000 measurements have been performed using portable salt meters in

Treatment of gummy smile: Gingival recontouring with the containment of the elevator muscle of the upper lip and wing of nose. A surgery innovation technique.

Science.gov (United States)

Storrer, Carmen Lucia Mueller; Valverde, Fabiane Kristine Bochenek; Santos, Felipe Rychuv; Deliberador, Tatiana Miranda

2014-09-01

The containment of the elevator muscle of the upper lip and wing of nose was used for the treatment of patients with gummy smile. This technique had corrected esthetic alterations of smile, reducing the upper lip elevation, which results in a smaller gingival display. An upper lip lengthening as well as a reduction in the upper lip shortening when the patient smiled could be observed. The high smile line was corrected without compromising the labial harmony. This study presents an innovative and effective therapeutic option to obtain a natural and harmonious smile. The patient expressed a high degree of satisfaction.

Treatment of gummy smile: Gingival recontouring with the containment of the elevator muscle of the upper lip and wing of nose. A surgery innovation technique

Directory of Open Access Journals (Sweden)

Carmen Lucia Mueller Storrer

2014-01-01

Full Text Available The containment of the elevator muscle of the upper lip and wing of nose was used for the treatment of patients with gummy smile. This technique had corrected esthetic alterations of smile, reducing the upper lip elevation, which results in a smaller gingival display. An upper lip lengthening as well as a reduction in the upper lip shortening when the patient smiled could be observed. The high smile line was corrected without compromising the labial harmony. This study presents an innovative and effective therapeutic option to obtain a natural and harmonious smile. The patient expressed a high degree of satisfaction.

Resource Conservation and Recovery Act closure plan for the Intermediate-Level Transuranic Storage Facility mixed waste container storage units

International Nuclear Information System (INIS)

Nolte, E.P.; Spry, M.J.; Stanisich, S.N.

1992-11-01

This document describes the proposed plan for clean closure of the Intermediate-Level Transuranic Storage Facility mixed waste container storage units at the Idaho National Engineering Laboratory in accordance with the Resource Conservation and Recovery Act closure requirements. Descriptions of the location, size, capacity, history, and current status of the units are included. The units will be closed by removing waste containers in storage, and decontamination structures and equipment that may have contacted waste. Sufficient sampling and documentation of all activities will be performed to demonstrate clean closure. A tentative schedule is provided in the form of a milestone chart

Do stable non-ST-segment elevation acute coronary syndromes require admission to coronary care units?

Science.gov (United States)

van Diepen, Sean; Lin, Meng; Bakal, Jeffrey A; McAlister, Finlay A; Kaul, Padma; Katz, Jason N; Fordyce, Christopher B; Southern, Danielle A; Graham, Michelle M; Wilton, Stephen B; Newby, L Kristin; Granger, Christopher B; Ezekowitz, Justin A

2016-05-01

Clinical practice guidelines recommend admitting patients with stable non-ST-segment elevation acute coronary syndrome (NSTE ACS) to telemetry units, yet up to two-thirds of patients are admitted to higher-acuity critical care units (CCUs). The outcomes of patients with stable NSTE ACS initially admitted to a CCU vs a cardiology ward with telemetry have not been described. We used population-based data of 7,869 patients hospitalized with NSTE ACS admitted to hospitals in Alberta, Canada, between April 1, 2007, and March 31, 2013. We compared outcomes among patients initially admitted to a CCU (n=5,141) with those admitted to cardiology telemetry wards (n=2,728). Patients admitted to cardiology telemetry wards were older (median 69 vs 65years, PST-segment myocardial infarction or unstable angina. There were no differences in clinical outcomes observed between patients with NSTE ACS initially admitted to a ward or a CCU. These findings suggest that stable NSTE ACS may be managed appropriately on telemetry wards and presents an opportunity to reduce hospital costs and critical care capacity strain. Copyright © 2016 Elsevier Inc. All rights reserved.

Synthesis and Excellent Duplex Stability of Oligonucleotides Containing 2'-Amino-LNA Functionalized with Galactose Units

DEFF Research Database (Denmark)

Kumar, Rajesh; Ries, Annika; Wengel, Jesper

2017-01-01

A convenient method for the preparation of oligonucleotides containing internally-attached galactose and triantennary galactose units has been developed based on click chemistry between 2'-N-alkyne 2'-amino-LNA nucleosides and azido-functionalized galactosyl building blocks. The synthesized...

Fukushima Daiichi Unit 1 power plant containment analysis using GOTHIC

International Nuclear Information System (INIS)

Ozdemir, Ozkan Emre; George, Thomas L.; Marshall, Mervin D.

2015-01-01

Highlights: • The inclusion of vent heat transfer had a significant impact on the overall containment response. • The vent heat transfer and condensation results in lower containment pressure. • The reduced gas transfer to the wetwell via the vents results in higher hydrogen concentration in the drywell. - Abstract: This paper is a part of Fukushima Technical Evaluation Project (EPRI, 2013a, 2014a, 2015) which investigates various aspects of the Fukushima Daiichi event using the GOTHIC code. The analysis takes advantage of the capability of GOTHIC to model certain aspects of the system geometry and behavior in more detail than typically considered in containment performance analysis. GOTHIC is a general purpose thermal hydraulics code that is used extensively in the nuclear industry for system design support, licensing support and safety analysis. It has the capability to model 3-dimensional flow behavior including the effects of turbulence, diffusion and buoyancy (EPRI, 2014b). This allows GOTHIC to be used in cases where mixing effects and stratification are important. The analysis presented here considers the events at Fukushima Daiichi Unit 1 (1F1) following the tsunami and leading up to the time of the hydrogen detonation in the 1F1 Reactor Building. The 1F1 MAAP5 Baseline Scenario (EPRI, 2013b) is used to define the steam, hydrogen and carbon-monoxide source terms from the primary system and the core concrete interaction. The model incorporates three dimensional modeling of the drywell, wetwell and connecting vent system that can predict the 3-dimensional flow patterns and the temperature and gas distributions. The model also includes leakage to the surrounding reactor building and the wetwell vent to the stack. The 3D containment model includes models for the heat transfer from the steam and gas in the drywell vent system to the torus room, wetwell gas space and pool. Inclusion of vent heat transfer had a significant impact on the overall containment

GOTHIC Simulation of Passive Containment Cooling System

International Nuclear Information System (INIS)

Ha, Huiun; Kim, Hangon

2013-01-01

The performance of this system depends on the condensation of steam moving downward inside externally cooled vertical tubes. AES-2006: During a DBA, heat is removed by internally cooled vertical tubes, which are located in containment. We are currently developing the conceptual design of Innovative PWR, which is will be equipped with various passive safety features, including PCCS. We have plan to use internal heat exchanger (HX) type PCCS with concrete containment. In this case, the elevation of HXs is important to ensure the heat removal during accidents. In general, steam is lighter than air mixture in containment. So, steam may be collected at the upper side of containment. It means that higher elevation of HXs, larger heat removal efficiency of those. So, the aim of the present paper is to give preliminary study on variation of heat removal performance according to elevation of HXs. With reference to the design specification of the current reactors including APR+, we had determined conceptual design of PCCS. Using it, we developed a GOTHIC model of the APR1400 containment was adopted PCCS. This calculation model is described herein and representative results of calculation are presented. APR 1400 GOTHIC model was developed for PCCS performance calculation and sensitivity test according to installation elevation of PCCXs. Calculation results confirm that PCCS is working properly. It is found that the difference due to the installation elevation of PCCXs is insignificant at this preliminary analysis, however, further studies should be performed to confirm final performance of PCCS according to the installation elevation. These insights are important for developing the PCCS of Innovative PWR

GOTHIC Simulation of Passive Containment Cooling System

Energy Technology Data Exchange (ETDEWEB)

Ha, Huiun; Kim, Hangon [Korea Hydro and Nuclear Power Co. Ltd., Daejeon (Korea, Republic of)

2013-05-15

The performance of this system depends on the condensation of steam moving downward inside externally cooled vertical tubes. AES-2006: During a DBA, heat is removed by internally cooled vertical tubes, which are located in containment. We are currently developing the conceptual design of Innovative PWR, which is will be equipped with various passive safety features, including PCCS. We have plan to use internal heat exchanger (HX) type PCCS with concrete containment. In this case, the elevation of HXs is important to ensure the heat removal during accidents. In general, steam is lighter than air mixture in containment. So, steam may be collected at the upper side of containment. It means that higher elevation of HXs, larger heat removal efficiency of those. So, the aim of the present paper is to give preliminary study on variation of heat removal performance according to elevation of HXs. With reference to the design specification of the current reactors including APR+, we had determined conceptual design of PCCS. Using it, we developed a GOTHIC model of the APR1400 containment was adopted PCCS. This calculation model is described herein and representative results of calculation are presented. APR 1400 GOTHIC model was developed for PCCS performance calculation and sensitivity test according to installation elevation of PCCXs. Calculation results confirm that PCCS is working properly. It is found that the difference due to the installation elevation of PCCXs is insignificant at this preliminary analysis, however, further studies should be performed to confirm final performance of PCCS according to the installation elevation. These insights are important for developing the PCCS of Innovative PWR.

Early results from an experimental program to determine the behavior of containment piping penetration bellows subjected to severe accident conditions

International Nuclear Information System (INIS)

Lambert, L.D.; Parks, M.B.

1994-01-01

Containment piping penetration bellows are an integral part of the pressure boundary in steel containments in the United States (US). Their purpose is to minimize loading on the containment shell caused by differential movement between the piping and the containment. This differential movement is typically caused by thermal gradients generated during startup and shutdown of the reactor, but can be caused by earthquake, a loss-of-coolant accident (LOCA), or ''severe'' accidents. In the event of a severe accident, the bellows would be subjected to pressure, temperature, and deflection well beyond the design basis. Most bellows are installed such that they would be subjected to elevated internal pressure, elevated temperature, axial compression, and lateral deflection during a severe accident. A few bellows would be subjected to external pressure and axial elongation, as well as elevated temperature and lateral deflection. The purpose of this experimental program is to examine the potential for leakage of containment bellows during a severe accident. The test series subjects bellows to various levels and combinations of internal pressure, elevated temperature, axial compression or elongation, and lateral deformation. The experiments are being conducted in two parts. For Part 1, all bellows specimens are tested in ''like-new'' condition, without regard for the possible degrading effect of corrosion that has been observed in some containment piping bellows in the US Part I testing, which included 13 bellows tests, has been completed. The second part of the experimental program, in which bellows are subjected to simulated corrosive environments prior to testing, has just just begun. The Part I experiments have shown that bellows in ''like-new'' condition can withstand elevated temperatures and pressures along with large deformations before leaking. In most cases, the like-new bellows were fully compressed without developing any leakage

Resource Conservation and Recovery Act (RCRA) Part B permit application for container storage units at the Oak Ridge Y-12 Plant

International Nuclear Information System (INIS)

1994-08-01

This document contains Part B of the Permit Application for Container Storage Units at the Oak Ridge Y-12 Plant. Sections cover the following areas: Facility description; Waste characteristics; Process information; Ground water monitoring; Procedures to prevent hazards; Contingency plan; Personnel training; Closure plan, post closure plan, and financial requirements; Recordkeeping; Other federal laws; Organic air emissions; Solid waste management units; and Certification

Resource Conservation and Recovery Act (RCRA) Part B permit application for container storage units at the Oak Ridge Y-12 Plant

Energy Technology Data Exchange (ETDEWEB)

1994-08-01

This document contains Part B of the Permit Application for Container Storage Units at the Oak Ridge Y-12 Plant. Sections cover the following areas: Facility description; Waste characteristics; Process information; Ground water monitoring; Procedures to prevent hazards; Contingency plan; Personnel training; Closure plan, post closure plan, and financial requirements; Recordkeeping; Other federal laws; Organic air emissions; Solid waste management units; and Certification.

TMI-2 auxiliary building elevator shaft and pit decontamination

Energy Technology Data Exchange (ETDEWEB)

Bengel, T.G.

1986-01-01

Decontamination of the elevator pit and shaft in the auxiliary building at Three Mile Island Unit 2 (TMI-2) was performed to remove high radiation and contamination levels which prevented personnel from utilizing the elevator. The radiation and contamination levels in the TMI-2 auxiliary building elevator shaft have been reduced to the point where plant personnel are again permitted to ride in the elevator without a radiation work permit, with the exception of access to the 281-ft (basement) level. Based on the declassification and expanded use of the elevator, the task goal has been met. The tax expended 16.16 man-rem and 621 man-hours.

Containment Response Analysis for Equipment Qualification of Kori Nuclear Power Plant Unit 3 and 4

Energy Technology Data Exchange (ETDEWEB)

Byun, Choong Sup; Song, Dong Soo; Hwang, Yong Jun [Korea Electric Power Research Institute, Taejon (Korea, Republic of); Seo, Kwi Hyun; Song, Wan Jung [ENERGEO Inc., Sungnam (Korea, Republic of)

2006-07-01

Equipment that is used to perform a necessary safety function must be capable of maintaining functional operability under all service condition postulated to occur during the installed life for the time it is required. The pressure and temperature analyses for loss of coolant accident and main steam line break accident provide the bounding test envelope inside containment for the operability evaluation of safety equipment in harsh environmental. This paper describes the results of the containment pressure and temperature analysis for the equipment qualification (EQ) envelopes of Kori unit 3 and 4.

Attributes for NHDPlus Catchments (Version 1.1) in the Conterminous United States: Artificial Drainage (1992) and Irrigation Types (1997)

Science.gov (United States)

Wieczorek, Michael; LaMotte, Andrew E.

2010-01-01

incorporates many of the best features of the National Hydrography Dataset (NHD) and the National Elevation Dataset (NED). The NHDPlus includes a stream network (based on the 1:100,00-scale NHD), improved networking, naming, and value-added attributes (VAAs). NHDPlus also includes elevation-derived catchments (drainage areas) produced using a drainage enforcement technique first widely used in New England, and thus referred to as "the New England Method." This technique involves "burning in" the 1:100,000-scale NHD and when available building "walls" using the National Watershed Boundary Dataset (WBD). The resulting modified digital elevation model (HydroDEM) is used to produce hydrologic derivatives that agree with the NHD and WBD. Over the past two years, an interdisciplinary team from the U.S. Geological Survey (USGS), and the U.S. Environmental Protection Agency (USEPA), and contractors, found that this method produces the best quality NHD catchments using an automated process (USEPA, 2007). The NHDPlus dataset is organized by 18 Production Units that cover the conterminous United States. The NHDPlus version 1.1 data are grouped by the U.S. Geological Survey's Major River Basins (MRBs, Crawford and others, 2006). MRB1, covering the New England and Mid-Atlantic River basins, contains NHDPlus Production Units 1 and 2. MRB2, covering the South Atlantic-Gulf and Tennessee River basins, contains NHDPlus Production Units 3 and 6. MRB3, covering the Great Lakes, Ohio, Upper Mississippi, and Souris-Red-Rainy River basins, contains NHDPlus Production Units 4, 5, 7 and 9. MRB4, covering the Missouri River basins, contains NHDPlus Production Units 10-lower and 10-upper. MRB5, covering the Lower Mississippi, Arkansas-White-Red, and Texas-Gulf River basins, contains NHDPlus Production Units 8, 11 and 12. MRB6, covering the Rio Grande, Colorado and Great Basin River basins, contains NHDPlus Production Units 13, 14, 15 and 16. MRB7, covering the Pacific Northwest River basins, contains

Energy efficient elevators and escalators

Energy Technology Data Exchange (ETDEWEB)

Patrao, Carlos; Fong, Joao; Almeida, Anibal de (Dep. Electrical Engineering, Univ. of Coimbra, Coimbra (Portugal)); Rivet, Luc

2009-07-01

Elevators and escalators are the crucial element that makes it practical to live and work several floors above ground - more than 4,3 million units are installed in Europe. Due to ageing of the European population the installation of elevators in single family houses is experiencing a significant growth, as well as equipping existing buildings. Elevators use about 4% of the electricity in tertiary sector buildings. High untapped saving potentials exist with respect to energy-efficient technologies, investment decisions and behavioural approaches, in these sectors. This paper presents preliminary results from the IEE project E4, whose overall objective is the improvement of the energy performance of elevators and escalators, in tertiary sector buildings and in multi family residential buildings. The project is characterizing people conveyors electricity consumption in the tertiary sector and in residential buildings in the EU. The installed park is characterised by a survey among elevators national associations in each country. An assessment of the barriers has been made in the first phase of the project and will be presented. Monitoring campaigns in elevators and escalators are being conducted in each country according to a common developed methodology. More than fifty elevators and escalators will be audited. This will allow the collection of load curves (start up, travel up and down, travel full and empty), including the characterization of standby consumption. Standby consumption of an elevator can represent up to 80% of the total energy consumed per year, and can be drastically reduced. This paper presents the preliminary results of the first ten audits performed in Portugal by Isr-UC.

Pre-IceBridge ATM L2 Icessn Elevation, Slope, and Roughness

Data.gov (United States)

National Aeronautics and Space Administration — The NASA Pre-IceBridge ATM Level-2 Icessn Elevation, Slope, and Roughness (BLATM2) data set contains resampled and smoothed elevation measurements of Arctic and...

Monocular Elevation Deficiency - Double Elevator Palsy

Science.gov (United States)

... Español Condiciones Chinese Conditions Monocular Elevation Deficiency/ Double Elevator Palsy En Español Read in Chinese What is monocular elevation deficiency (Double Elevator Palsy)? Monocular Elevation Deficiency, also known by the ...

Landscape unit based digital elevation model development for the freshwater wetlands within the Arthur C. Marshall Loxahatchee National Wildlife Refuge, Southeastern Florida

Science.gov (United States)

Xie, Zhixiao; Liu, Zhongwei; Jones, John W.; Higer, Aaron L.; Telis, Pamela A.

2011-01-01

The hydrologic regime is a critical limiting factor in the delicate ecosystem of the greater Everglades freshwater wetlands in south Florida that has been severely altered by management activities in the past several decades. "Getting the water right" is regarded as the key to successful restoration of this unique wetland ecosystem. An essential component to represent and model its hydrologic regime, specifically water depth, is an accurate ground Digital Elevation Model (DEM). The Everglades Depth Estimation Network (EDEN) supplies important hydrologic data, and its products (including a ground DEM) have been well received by scientists and resource managers involved in Everglades restoration. This study improves the EDEN DEMs of the Loxahatchee National Wildlife Refuge, also known as Water Conservation Area 1 (WCA1), by adopting a landscape unit (LU) based interpolation approach. The study first filtered the input elevation data based on newly available vegetation data, and then created a separate geostatistical model (universal kriging) for each LU. The resultant DEMs have encouraging cross-validation and validation results, especially since the validation is based on an independent elevation dataset (derived by subtracting water depth measurements from EDEN water surface elevations). The DEM product of this study will directly benefit hydrologic and ecological studies as well as restoration efforts. The study will also be valuable for a broad range of wetland studies.

VALIDATION OF THE ASTER GLOBAL DIGITAL ELEVATION MODEL VERSION 3 OVER THE CONTERMINOUS UNITED STATES

Directory of Open Access Journals (Sweden)

D. Gesch

2016-06-01

Full Text Available The ASTER Global Digital Elevation Model Version 3 (GDEM v3 was evaluated over the conterminous United States in a manner similar to the validation conducted for the original GDEM Version 1 (v1 in 2009 and GDEM Version 2 (v2 in 2011. The absolute vertical accuracy of GDEM v3 was calculated by comparison with more than 23,000 independent reference geodetic ground control points from the U.S. National Geodetic Survey. The root mean square error (RMSE measured for GDEM v3 is 8.52 meters. This compares with the RMSE of 8.68 meters for GDEM v2. Another important descriptor of vertical accuracy is the mean error, or bias, which indicates if a DEM has an overall vertical offset from true ground level. The GDEM v3 mean error of −1.20 meters reflects an overall negative bias in GDEM v3. The absolute vertical accuracy assessment results, both mean error and RMSE, were segmented by land cover type to provide insight into how GDEM v3 performs in various land surface conditions. While the RMSE varies little across cover types (6.92 to 9.25 meters, the mean error (bias does appear to be affected by land cover type, ranging from −2.99 to +4.16 meters across 14 land cover classes. These results indicate that in areas where built or natural aboveground features are present, GDEM v3 is measuring elevations above the ground level, a condition noted in assessments of previous GDEM versions (v1 and v2 and an expected condition given the type of stereo-optical image data collected by ASTER. GDEM v3 was also evaluated by differencing with the Shuttle Radar Topography Mission (SRTM dataset. In many forested areas, GDEM v3 has elevations that are higher in the canopy than SRTM. The overall validation effort also included an evaluation of the GDEM v3 water mask. In general, the number of distinct water polygons in GDEM v3 is much lower than the number in a reference land cover dataset, but the total areas compare much more closely.

Validation of the ASTER Global Digital Elevation Model version 3 over the conterminous United States

Science.gov (United States)

Gesch, Dean B.; Oimoen, Michael J.; Danielson, Jeffrey J.; Meyer, David; Halounova, L; Šafář, V.; Jiang, J.; Olešovská, H.; Dvořáček, P.; Holland, D.; Seredovich, V.A.; Muller, J.P.; Pattabhi Rama Rao, E.; Veenendaal, B.; Mu, L.; Zlatanova, S.; Oberst, J.; Yang, C.P.; Ban, Y.; Stylianidis, S.; Voženílek, V.; Vondráková, A.; Gartner, G.; Remondino, F.; Doytsher, Y.; Percivall, George; Schreier, G.; Dowman, I.; Streilein, A.; Ernst, J.

2016-01-01

The ASTER Global Digital Elevation Model Version 3 (GDEM v3) was evaluated over the conterminous United States in a manner similar to the validation conducted for the original GDEM Version 1 (v1) in 2009 and GDEM Version 2 (v2) in 2011. The absolute vertical accuracy of GDEM v3 was calculated by comparison with more than 23,000 independent reference geodetic ground control points from the U.S. National Geodetic Survey. The root mean square error (RMSE) measured for GDEM v3 is 8.52 meters. This compares with the RMSE of 8.68 meters for GDEM v2. Another important descriptor of vertical accuracy is the mean error, or bias, which indicates if a DEM has an overall vertical offset from true ground level. The GDEM v3 mean error of −1.20 meters reflects an overall negative bias in GDEM v3. The absolute vertical accuracy assessment results, both mean error and RMSE, were segmented by land cover type to provide insight into how GDEM v3 performs in various land surface conditions. While the RMSE varies little across cover types (6.92 to 9.25 meters), the mean error (bias) does appear to be affected by land cover type, ranging from −2.99 to +4.16 meters across 14 land cover classes. These results indicate that in areas where built or natural aboveground features are present, GDEM v3 is measuring elevations above the ground level, a condition noted in assessments of previous GDEM versions (v1 and v2) and an expected condition given the type of stereo-optical image data collected by ASTER. GDEM v3 was also evaluated by differencing with the Shuttle Radar Topography Mission (SRTM) dataset. In many forested areas, GDEM v3 has elevations that are higher in the canopy than SRTM. The overall validation effort also included an evaluation of the GDEM v3 water mask. In general, the number of distinct water polygons in GDEM v3 is much lower than the number in a reference land cover dataset, but the total areas compare much more closely.

The 3D Elevation Program national indexing scheme

Science.gov (United States)

Thatcher, Cindy A.; Heidemann, Hans Karl; Stoker, Jason M.; Eldridge, Diane F.

2017-11-02

The 3D Elevation Program (3DEP) of the U.S. Geological Survey (USGS) acquires high-resolution elevation data for the Nation. This program has been operating under an opportunity-oriented approach, acquiring light detection and ranging (lidar) projects of varying sizes scattered across the United States. As a result, the national 3DEP elevation layer is subject to data gaps or unnecessary overlap between adjacent collections. To mitigate this problem, 3DEP is adopting a strategic, systematic approach to national data acquisition that will create efficiencies in efforts to achieve nationwide elevation data coverage and help capture additional Federal and non-Federal investments resulting from advance awareness of proposed acquisitions and partnership opportunities. The 3DEP Working Group, an interagency group managed by the USGS, has agreed that all future 3DEP collections within the lower 48 States should be coordinated by using a 1-kilometer by 1-kilometer tiling scheme for the conterminous United States. Fiscal Year 2018 is being considered a transition year, and in Fiscal Year 2019 the national indexing scheme will be fully implemented, so that all 3DEP-supported projects will be acquired and delivered in the national indexing scheme and projected into the Albers Equal Area projection. 

Localities With Elevated Radiation Background in the High Karst Zone of Montenegro

International Nuclear Information System (INIS)

Vukotic, P.; Svrkota, R.; Andjelic, T.; Zekic, R.; Antovic, N.

2011-01-01

Research aimed to find localities in Montenegro with an elevated terrestrial gamma background was conducted during the period 2008-2009. For this purpose, 138 localities which have geological formations known to contain minerals with potentially high concentrations of U, Th and K, were selected throughout the country for a dosimetric survey. There are four distinctive geotectonic units in Montenegro: the Adriatic-Ionian Zone (JZ), the Budva-Cukali Zone (BZ), the High Karst Zone (VK), and the Durmitor Tectonic Unit (DTJ). The central and southern parts of Montenegro belong to the VK zone, whose geological structure is predominated by Mesozoic carbonate sediments, with occurrences of red and white bauxite formations, Triassic volcanic rocks, Paleogene flysch sediments and Quaternary sediments. In total, 38 localities belonging to the VK zone were selected for field investigations of terrestrial radiation. Knowing from earlier investigations that in Montenegro the average absorbed dose-rate in the air, 1 m above the ground, is 55 nGy/h, it was arbitrarily adopted that only localities with absorbed doses at least 50 % above this average value would be considered as having a relatively elevated radiation background. Field measurements have shown that 12 of the surveyed localities in the VK zone have such elevated dose values, five of them being with the highest dose rates in Montenegro. Among these five sites, the highest dose rate (192 nGy/h) was found at a locality which lies on andesite volcanic rock, while the other four localities (131 - 149 nGy/h) lie on bauxite deposits. Compared to the other areas in the world known to have a high natural radiation background, all of these localities in Montenegro have a moderately elevated radiation level. From the 12 localities with a relatively elevated radiation background, soil samples have been collected and analyzed by gamma spectrometry to determine activity concentrations of 40K, 232Th, 235U, 238U, 226Ra and 137Cs

Elevating your elevator talk

Science.gov (United States)

An important and often overlooked item that every early career researcher needs to do is compose an elevator talk. The elevator talk, named because the talk should not last longer than an average elevator ride (30 to 60 seconds), is an effective method to present your research and yourself in a clea...

Continuous containment monitoring with containment pressure fluctuation

International Nuclear Information System (INIS)

Dick, J.E.

1996-01-01

The monitoring of the integrity of containments particularly but not exclusively for nuclear plants is dealt with in this invention. While this application is primarily concerned with containment monitoring in the context of the single unit design, it is expected that the concepts presented will be universally applicable to any containment design, including containments for non-nuclear applications such as biological laboratories. The nuclear industry has long been interested in a means of monitoring containment integrity on a continuous basis, that is, while the reactor is operating normally. 12 refs., 2 figs

Engineering evaluation/conceptual plan for the 200-UP-1 groundwater operable unit interim remedial measure

International Nuclear Information System (INIS)

Myers, D.A.; Swanson, L.C.; Weeks, R.S.; Giacinto, J.; Gustafson, F.W.; Ford, B.H.; Wittreich, C.; Parnell, S.; Green, J.

1995-04-01

This report presents an engineering evaluation and conceptual plan for an interim remedial measure (ERM) to address a uranium and technetium-99 groundwater plume and an associated nitrate contamination plume in the 200-UP-1 Groundwater Operable Unit located in the 200 West Area of the Hanford Site. This report provides information regarding the need and potentially achievable objectives and goals for an IRM and evaluates alternatives to contain elevated concentrations of uranium, technetium-99, nitrate, and carbon tetrachloride and to obtain information necessary to develop final remedial actions for the operable unit

Study of deuterium retention in/release from ITER-relevant Be-containing mixed material layers implanted at elevated temperatures

Energy Technology Data Exchange (ETDEWEB)

Sugiyama, K., E-mail: kazuyoshi.sugiyama@ipp.mpg.de [Max-Planck-Institut für Plasmaphysik, EURATOM Association, D-85748 Garching (Germany); Porosnicu, C. [National Institute for Laser, Plasma and Radiation Physics, EURATOM-MEdC Association, 077125 Bucharest (Romania); Jacob, W.; Roth, J.; Dürbeck, Th. [Max-Planck-Institut für Plasmaphysik, EURATOM Association, D-85748 Garching (Germany); Jepu, I.; Lungu, C.P. [National Institute for Laser, Plasma and Radiation Physics, EURATOM-MEdC Association, 077125 Bucharest (Romania)

2013-07-15

D implantation into Be-containing mixed material layers: Be, Be–W (W: ∼6 at.%) and Be–C (C: ∼50 at.%), was performed at elevated temperatures. The temperature dependence of D retention varied depending on the admixed element. D retention in Be and Be–W layers decreases with increasing implantation temperature, while the Be–C layers maintained rather high D retention in the present investigated temperature range (up to 623 K). D desorption behaviour from Be–C suggests the contribution of C–D bonds to D retention. W admixture into Be can significantly suppress D retention in Be. Long-term isothermal annealing at 513 and 623 K for D removal was also performed to simulate the ITER-wall-baking scenario. Even extended annealing at temperatures comparable to or lower than the implantation temperature does not lead to a significant release of retained D.

Containment Loads Analysis for CANDU6 Reactor using CONTAIN 2.0

International Nuclear Information System (INIS)

Kim, Tae H.; Yang, Chae Y.

2013-01-01

The containment plays an important role to limit the release of radioactive materials to the environment during design basis accidents (DBAs). Therefore, the containment has to maintain its integrity under DBA conditions. Generally, a containment functional DBA evaluation includes calculations of the key containment loads, i. e., pressure and temperature effects associated with a postulated large rupture of the primary or secondary coolant system piping. In this paper, the behavior of containment pressure and temperature was evaluated for loss of coolant accidents (LOCAs) of the Wolsong unit 1 in order to assess the applicability of CONTAIN 2.0 code for the containment loads analysis of the CANDU6 reactor. The containment pressure and temperature of the Wolsong unit 1 were evaluated using the CONTAIN 2.0 code and the results were compared with the CONTEMPT4 code. The peak pressure and temperature calculated by CONTAIN 2.0 agreed well with those of CONTEMPT4 calculation. The overall result of this analysis shows that the CONTAIN 2.0 code can apply to the containment loads analysis for the CANDU6 reactor

Troponin elevation in subarachnoid hemorrhage

Directory of Open Access Journals (Sweden)

Ioannis N. Mavridis

2015-03-01

Full Text Available Troponin (tr elevation in aneurysmal subarachnoid hemorrhage (SAH patients is often difficult to be appropriately assessed by clinicians, causing even disagreements regarding its management between neurosurgeons and cardiologists. The purpose of this article was to review the literature regarding the clinical interpretation of tr elevation in SAH. We searched for articles in PubMed using the key words: “troponin elevation” and “subarachnoid hemorrhage”. All of them, as well as relative neurosurgical books, were used for this review. Some type of cardiovascular abnormality develops in most SAH patients. Neurogenic stunned myocardium is a frequent SAH complication, due to catecholamine surge which induces cardiac injury, as evidenced by increased serum tr levels, electrocardiographic (ECG changes and cardiac wall motion abnormalities. Tr elevation, usually modest, is an early and specific marker for cardiac involvement after SAH and its levels peak about two days after SAH. Cardiac tr elevation predictors include poor clinical grade, intraventricular hemorrhage, loss of consciousness at ictus, global cerebral edema, female sex, large body surface area, lower systolic blood pressure, higher heart rate and prolonged Q-Tc interval. Elevated tr levels are associated with disability and death (especially tr >1 μg/L, worse neurological grade, systolic and diastolic cardiac dysfunction, pulmonary congestion, longer intensive care unit stay and incidence of vasospasm. Tr elevation is a common finding in SAH patients and constitutes a rightful cause of worry about the patients' cardiac function and prognosis. It should be therefore early detected, carefully monitored and appropriately managed by clinicians.

Synthesis of Dendrimer Containing Carbazole Unit as a Core Chromophore

International Nuclear Information System (INIS)

Han, Seung Choul; Lee, Jae Wook; Jin, Sungho

2012-01-01

Dendrimers, which are prepared by repetition of a given set of reactions using either divergent or convergent strategies, are highly branched and regular macromolecules with well-defined structures and have served as functional objects in nanotechnology and nano-materials science. Following conventional organic small molecules and polymers, dendrimers are now regarded as the third class of materials for use in organic light-emitting diodes (OLEDs) and have attracted much attention due to their distinguished properties. Dendrimers contain three distinct structural parts that are the core, end-groups, and branched units connecting core and periphery. For light-emitting dendrimers, the core is usually selected as the luminescent chromophore, and the dendrons and their periphery are charge transporting units and can also tune the solubility. In contrast to linear polymers, dendrimers are sphere-like with dimensions of the order of nanometers depending on the generation number. By careful structural design, dendrimers combine the potential advantages of both small molecules and polymers. Therefore, the innovative strategy different from conventional convergent and divergent routes has been required to simplify dendrimer synthesis. Recent solid chemistry is the click chemistry which is the copper-catalyzed 1,3-dipolar cycloaddition reaction between alkyne and azide developed by Sharpless and Tornφe. This reaction has many advantages: very high yields, mild and simple reaction conditions, oxygen and water tolerance, and easy isolation of product. This reaction is clearly a breakthrough in the synthesis of dendrimers and dendritic and polymer materials. We have developed the fusion and stitching methods for the synthesis of various dendrimers using click chemistry between an alkyne and an azide. Overall, this method was found to be a straightforward strategy for the synthesis of triazole-based dendrimers. Taking advantage of this fact, herein we report a feasible route

Fluorescent Oligonucleotides Containing a 2-Ethynylfluorene-or 2-Ethynylfluorenone-labeled 2'-Deoxyguanosine Unit: Fluorescence Changes upon Duplex Formation

Energy Technology Data Exchange (ETDEWEB)

Kim, Min Ji; Hwang, Gil Tae [Kyungpook National University, Daegu (Korea, Republic of)

2016-08-15

Two new DNA probes bearing a fluorescent deoxyguanosine unit labeled with 2-ethynylfluorene (G{sup FL} )or 2-ethynylfluorenone (G{sup FO}) were synthesized and examined for their efficiency as quencher-free linear beacon probes. Oligodeoxynucleotides (ODNs) containing a G{sup FL} or G{sup FO} unit exhibit low thermal selectivity and few distinctive fluorescence changes upon duplex formation due to the syn conformation about the glycosidic bond. An exciplex emission was observed when the G{sup FL} unit of ODNs bearing adenine flanking bases was positioned opposite to the adenine nucleobases.

Engineering evaluation/conceptual plan for the 200-UP-1 Groundwater Operable Unit interim remedial measure. Revision 2

International Nuclear Information System (INIS)

1996-03-01

This report presents an engineering evaluation and conceptual plan for an interim remedial measure (IRM) to address a uranium and technetium-99 groundwater plume in the 200-UP-1 Groundwater Operable Unit located in the 200 West Area of the Hanford Site. This report provides information regarding the need for an IRM and its potentially achievable objectives and goals. The report also evaluates alternatives to contain elevated concentrations of uranium and technetium-99 and to obtain information necessary to develop final remedial actions for the operable unit

National requirements for improved elevation data

Science.gov (United States)

Snyder, Gregory I.; Sugarbaker, Larry J.; Jason, Allyson L.; Maune, David F.

2014-01-01

This report presents the results of surveys, structured interviews, and workshops conducted to identify key national requirements for improved elevation data for the United States and its territories, including coastlines. Organizations also identified and reported the expected economic benefits that would be realized if their requirements for improved elevation were met (appendixes 1–3). This report describes the data collection methodology and summarizes the findings. Participating organizations included 34 Federal agencies, 50 States and two territories, and a sampling of local governments, tribes, and nongovernmental orgnizations. The nongovernmental organizations included The Nature Conservancy and a sampling of private sector businesses. These data were collected in 2010-2011 as part of the National Enhanced Elevation Assessment (NEEA), a study to identify program alternatives for better meeting the Nation’s elevation data needs. NEEA tasks included the collection of national elevation requirements; analysis of the benefits and costs of meeting these requirements; assessment of emerging elevation technologies, lifecycle data management needs, and costs for managing and distributing a national-scale dataset and derived products; and candidate national elevation program alternatives that balance costs and benefits in meeting the Nation’s elevation requirements. The NEEA was sponsored by the National Digital Elevation Program (NDEP), a government coordination body with the U.S. Geological Survey (USGS) as managing partner that includes the National Geospatial-Intelligence Agency (NGA), the Federal Emergency Management Agency (FEMA), the Natural Resources Conservation Service (NRCS), the U.S. Army Corps of Engineers (USACE), and the National Oceanic and Atmospheric Administration (NOAA), among the more than a dozen agencies and organizations. The term enhanced elevation data as used in this report refers broadly to three-dimensional measurements of land or

PWR primary system chemistry: Experience with elevated pH at Millstone Point Unit 3

International Nuclear Information System (INIS)

Bergmann, C.A.; McAtee, K.R.; Roesmer, J.

1990-08-01

The maintenance of an elevated pH of the hot reactor coolant in several plants for a fraction of their respective fuel cycles confirmed earlier laboratory findings that an elevated pH (>6.9 at temperature) resulted in reduced component radiation fields. In view of the potential radiological benefits of elevated coolant pH operation, Northeast Utilities (NU) in support of an EPRI- Westinghouse program, agreed to operate the Millstone 3 plants as a demonstration of elevated coolant pH during operation with extended fuel cycles. This report represents the data and describes the effects of operation of the Millstone 3 cycle 2 core at an elevated hot coolant pH of 7.0--7.5 on Zircaloy cladding corrosion, and on the buildup of core crud and excore radiation fields. The following preliminary conclusion were made based on an evaluation of the data obtained after one cycle of Millstone 3 elevated coolant pH operation. Although some of the measured zirconium dioxide thicknesses are greater than expected, the data does not indicate a significant lithium effect on the corrosion rate of the fuel cladding because of the relatively high variability of thickness measurements on rods of similar duty. There was no observable effect of the higher pH operation on any of the other fuel assembly components. Changes in core crude deposit thickness, chemical and radiochemical composition and apparent residence time were noted. These changes are consistent with the expected effects of a more dissolving coolant on activity and crud transport in a primary circuit. The overall radiation exposure rate trends from cycle 1 to cycle 2 indicated a favorable effect of the higher pH operation. 17 figs., 11 tabs

Well Construction Details, Groundwater Elevations, and Figures for the Tijeras Arroyo Groundwater Area at Sandia National Laboratories, New Mexico

Energy Technology Data Exchange (ETDEWEB)

Copland, John R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-01-01

This Sandia National Laboratories / New Mexico (SNL/NM) submittal contains groundwater information that the United States Geological Survey (USGS) has requested. The USGS will use the information to assist Kirtland Air Force Base (KAFB) in its ongoing groundwater studies. The information in this submittal contains well-construction details and groundwater-elevation data for monitoring wells that SNL/NM has installed. Relevant well-construction data from other government agencies are also summarized. This submittal contains four data tables and three figures. Information in the tables has been used by SNL/NM to prepare groundwater compliance reports that have previously incorporated the three figures. The figures depict the potentiometric surface for the Perched Groundwater System, the potentiometric surface for the Regional Aquifer, and a Conceptual Site Model for the vicinity of Tijeras Arroyo in the northern portion of KAFB.

Elevated temperature effects on concrete properties

International Nuclear Information System (INIS)

Grant, P.R.; Gruber, R.S.; Van Katwijk, C.

1993-08-01

The design of facilities to process or store radioactive wastes presents many challenging engineering problems. Such facilities must not only provide for safe storage of radioactive wastes but they must also be able to maintain confinement of these materials during and after natural phenomena events. Heat generated by the radioactive decay of the wastes will cause the temperature of the concrete containment structure to increase to a magnitude higher than that found in conventional structures. These elevated temperatures will cause strength-related concrete properties to degrade over time. For concrete temperatures less than 150 degree F, no reduction in strength is taken and the provisions of ACI 349, which states that higher temperatures are allowed if tests are provided to evaluate the reduction in concrete strength properties, apply. Methods proposed in a Pacific Northwest Laboratory (PNL) report, Modeling of Time-Variant Concrete Properties at Elevated Temperatures, can be used to evaluate the effects of elevated temperatures on concrete properties. Using these modified concrete properties the capacity of a concrete structure, subjected to elevated temperatures, to resist natural phenomena hazards can be determined

ASTER Orthorectified Digital Elevation Model (DEM) V003

Data.gov (United States)

National Aeronautics and Space Administration — The ASTER L3 DEM and Orthorectified Images form a multi-file product that contains both the Digital Elevation Model (DEM), and the Orthorectified Image products....

Development of the Computer Code to Determine an Individual Radionuclides in the Rad-wastes Container for Ulchin Units 3 and 4

Energy Technology Data Exchange (ETDEWEB)

Kang, D.W.; Chi, J.H.; Goh, E.O. [Korea Electric Power Research Institute, Taejon (Korea)

2001-07-01

A computer program, RASSAY was developed to evaluate accurately the activities of various nuclides in the rad-waste container for Ulchin units 3 and 4. This is the final report of the project, {sup D}evelopment of the Computer Code to Determine an Individual Radionuclides in the Rad-wastes Container for Ulchin Units 3 and 4 and includes the followings; 1) Structure of the computer code, RASSAY 2) An example of surface dose calculation by computer simulation using MCNP code 3) Methods of sampling and activity measurement of various Rad-wastes. (author). 21 refs., 35 figs., 6 tabs.

A spider elevator

Energy Technology Data Exchange (ETDEWEB)

Butylkin, A.V.; Butylkin, V.A.; Izosimov, A.M.

1983-01-01

A spider elevator is proposed which contains a body, a wedge clamp with wedges hinged to each other, a subassembly for holding the wedge clamp in the open and closed positions and a mechanism for changing the wedge clamp, which is made in the form of levers with ears for cleats and installed in the body with the capability of turning. To increase reliability in the operational mode through using the external force for clamping the pipe, the free ends of the levers are hinged with the body by a power cylinder.

Assessing LiDAR elevation data for KDOT applications.

Science.gov (United States)

2013-02-01

LiDAR-based elevation surveys are a cost-effective means for mapping topography over large areas. LiDAR : surveys use an airplane-mounted or ground-based laser radar unit to scan terrain. Post-processing techniques are : applied to remove vegetation ...

[Risk factors for elevated serum total bile acid in preterm infants].

Science.gov (United States)

Song, Yan-Ting; Wang, Yong-Qin; Zhao, Yue-Hua; Zhu, Hai-Ling; Liu, Qian; Zhang, Xiao; Gao, Yi-Wen; Zhang, Wei-Ye; Sang, Yu-Tong

2018-03-01

To study the risk factors for elevated serum total bile acid (TBA) in preterm infants. A retrospective analysis was performed for the clinical data of 216 preterm infants who were admitted to the neonatal intensive care unit. According to the presence or absence of elevated TBA (TBA >24.8 μmol/L), the preterm infants were divided into elevated TBA group with 53 infants and non-elevated TBA group with 163 infants. A univariate analysis and an unconditional multivariate logistic regression analysis were used to investigate the risk factors for elevated TBA. The univariate analysis showed that there were significant differences between the elevated TBA group and the non-elevated TBA group in gestational age at birth, birth weight, proportion of small-for-gestational-age infants, proportion of infants undergoing ventilator-assisted ventilation, fasting time, parenteral nutrition time, and incidence of neonatal respiratory failure and sepsis (PTBA in preterm infants. Low birth weight and neonatal sepsis may lead to elevated TBA in preterm infants.

Void growth and coalescence in metals deformed at elevated temperature

DEFF Research Database (Denmark)

Klöcker, H.; Tvergaard, Viggo

2000-01-01

For metals deformed at elevated temperatures the growth of voids to coalescence is studied numerically. The voids are assumed to be present from the beginning of deformation, and the rate of deformation considered is so high that void growth is dominated by power law creep of the material, without...... any noticeable effect of surface diffusion. Axisymmetric unit cell model computations are used to study void growth in a material containing a periodic array of voids, and the onset of the coalescence process is defined as the stage where plastic flow localizes in the ligaments between neighbouring...... voids. The focus of the study is on various relatively high stress triaxialties. In order to represent the results in terms of a porous ductile material model a set of constitutive relations are used, which have been proposed for void growth in a material undergoing power law creep....

Novel poly (arylene-ether-ether-ketone)s containing preformed imide unit and pendant long chain alkyl group

International Nuclear Information System (INIS)

Sayyed, Maheboob M.; Maldar, Noormahmad N.

2010-01-01

The studies were carried out to get preformed imide unit containing PEEKs and Co-PEEKs with pendant long chain alkyl group. Thus two new bisphenols; N,N'-bis (4-hydroxy 2-pentadecyl phenyl) pyromellitimide (HPI) (I) and N,N'-bis (4-hydroxy 2-pentadecyl phenyl 3,3',4,4'-benzophenone tetracarboxylic imide (HBI) (II) containing imide unit, pendant C-15 alkyl substituents were synthesized, characterized by spectral data and polycondensed with 4,4'-difluorobenzophenone (DFB) to yield several PEEK and Co-PEEKs. The polymers were characterized by FTIR, inherent viscosity, solubility, and XRD. The polymers were obtained in good yields and had inherent viscosities up to 0.65 dL/g in NMP. Polymerization of mixture of two bisphenols; [(I) and BPA]; and [(II) and BPA] in various mol%, with DFB gave number of the copolymers viz. Co-PEEK-BPAPI and Co-PEEK-BPABI. Many of the Co-PEEKs had good solubility in polar solvents. The solubility of PEEK containing bulky pendant alkyl substituents did not much improve probably due to simultaneous presence of rigid imide structures. XRD analysis indicated that PEEK and Co-PEEKs were partially crystalline or amorphous depending on the nature and % content of imide-bisphenol. These new PEEK materials can be used as high performance films, coatings, gas separation membranes, in aerospace and nuclear industries.

SYNTHESIS AND CHARACTERIZATION OF NOVEL BIPOLAR PPV-BASED COPOLYMER CONTAINING TRIAZOLE AND CARBAZOLE UNITS

Institute of Scientific and Technical Information of China (English)

Ze Liu; Li-xiang Wang; Xia-bin Jing; Fo-song Wang

2001-01-01

Two new blue light-emitting PPV-based conjugated copolymers containing both an electron-withdrawing unit (triazole-TAZ) and electron-rich moieties (carbazole-CAR and bicarbazole-BCAR) were prepared by Wittig condensation polymerization between the triazole diphosphonium salt and the corresponding dialdehyde monomers. Their structures and properties were characterized by FT-IR, TGA, DSC, UV-Vis, PL spectroscopy and electrochemical measurements. The resulting copolymers are soluble in common organic solvents and thermally stable with a Ts of 147C for TAZ-CAR-PPV and of 157C for TAZ-BCAR-PPV. The maximum photoluminescence wavelengths of TAZ-CAR-PPV and TAZ-BCAR-PPV film appear at 460 nm and 480 nm, respectively. Cyclic voltammetry measurement demonstrates that TAZ-BCAR-PPV has good electrochemical reversibility, while TAZ-CAR-PPV exhibits the irreversible redox process. The triazole unit was found to be an effective π-conjugation interrupter and can play the rigid spacer role in determining the emission colour of the resulting copolymer.

Ten-year weight gain is associated with elevated fasting insulin levels and precedes glucose elevation.

Science.gov (United States)

Pennings, Nicholas; Jaber, Johnny; Ahiawodzi, Peter

2018-05-01

Numerous studies have examined the relationship between endogenous insulin and weight change with mixed results. This study examined the relationship between fasting insulin levels, insulin resistance (IR), and 10-year weight change by glycaemic stage. Using data from the US National Health and Nutrition Examination Survey 2011-2014, 3840 participants were divided into 6 groups based on fasting glucose and fasting insulin levels. Fasting insulin concentrations were dichotomized into <25th percentile (normal) and ≥25th percentile (elevated). Ten-year weight change associated with fasting insulin was assessed by glycaemic stage. Average weight change over a 10-year period was higher in individuals with elevated insulin levels compared to the first quartile (1.40 lbs. vs 11.12 lbs, P < .0001). Across all groups, a 1 μU increase in fasting insulin levels resulted in a 0.52-pound increase in weight (P < .0001). Similarly, an increase in HOMA-IR was associated with increase in weight (1.32 lbs per IR unit, P < .0001). Marginal increases in weight were most pronounced in the normal insulin groups compared to elevated insulin groups and diminished as glycaemic stage progressed. Elevated fasting insulin level was positively associated with weight gain. The impact of fasting insulin and IR on weight gain preceded hyperglycaemia and diminished as glycaemic stage progressed. Copyright © 2018 John Wiley & Sons, Ltd.

PCB-containing wood floor finish is a likely source of elevated PCBs in residents' blood, household air and dust: a case study of exposure

Directory of Open Access Journals (Sweden)

Seryak Liesel M

2008-01-01

Full Text Available Abstract Background Polychlorinated biphenyls (PCBs are persistent pollutants identified worldwide as human blood and breast milk contaminants. Because they bioaccumulate, consumption of meat, fish, and dairy products predicts human blood concentrations. PCBs were also used widely in building materials, including caulks and paints, but few studies have evaluated the contribution of these exposures to body burden. Methods In an earlier study, we detected PCBs in indoor air in 31% of 120 homes on Cape Cod, MA. Two of the homes had much higher concentrations than the rest, so we retested to verify the initial finding, evaluate blood PCB concentrations of residents, and identify the PCB source. Results Air and dust concentrations remained elevated over 5 years between initial and follow-up sampling. Blood serum concentrations of PCBs in residents of the homes were generally elevated above the 95th percentile of a representative sample of the US population. Serum concentrations in residents and air and dust concentrations were especially high in a home where a resident reported use of PCB-containing floor finish in the past, and where the floor of one room was sanded and refinished just prior to sample collection. Conclusion This case-study suggests that PCB residues in homes may be more significant contributors to overall exposure than diet for some people, and that use of a commercially-available PCB-containing wood floor finish in residences during the 1950s and 1960s is an overlooked but potentially important source of current PCB exposure in the general population.

Carbon stocks of trees killed by bark beetles and wildfire in the western United States

International Nuclear Information System (INIS)

Hicke, Jeffrey A; Meddens, Arjan J H; Kolden, Crystal A; Allen, Craig D

2013-01-01

Forests are major components of the carbon cycle, and disturbances are important influences of forest carbon. Our objective was to contribute to the understanding of forest carbon cycling by quantifying the amount of carbon in trees killed by two disturbance types, fires and bark beetles, in the western United States in recent decades. We combined existing spatial data sets of forest biomass, burn severity, and beetle-caused tree mortality to estimate the amount of aboveground and belowground carbon in killed trees across the region. We found that during 1984–2010, fires killed trees that contained 5–11 Tg C year −1 and during 1997–2010, beetles killed trees that contained 2–24 Tg C year −1 , with more trees killed since 2000 than in earlier periods. Over their periods of record, amounts of carbon in trees killed by fires and by beetle outbreaks were similar, and together these disturbances killed trees representing 9% of the total tree carbon in western forests, a similar amount to harvesting. Fires killed more trees in lower-elevation forest types such as Douglas-fir than higher-elevation forest types, whereas bark beetle outbreaks also killed trees in higher-elevation forest types such as lodgepole pine and Engelmann spruce. Over 15% of the carbon in lodgepole pine and spruce/fir forest types was in trees killed by beetle outbreaks; other forest types had 5–10% of the carbon in killed trees. Our results document the importance of these natural disturbances in the carbon budget of the western United States. (letter)

Steam generator replacement in Bruce A Unit 1 and Unit 2

International Nuclear Information System (INIS)

Hart, R.S.

2007-01-01

The Bruce A Generating Station consists of four 900 MW class CANDU units. The reactor and Primary Heat Transport System for each Unit are housed within a reinforced concrete reactor vault. A large duct running below the reactor vaults accommodates the shared fuel handling system, and connects the four reactor vaults to the vacuum building. The reactor vaults, fuelling system duct and the vacuum building constitute the station vacuum containment system. Bruce A Unit 2 was shut down in 1995 and Bruce A Units 1, 3 and 4 were shutdown in 1997. Bruce A Units 3 and 4 were returned to service in late 2003 and are currently operating. Units 1 and 2 remain out of service. Bruce Power is currently undertaking a major rehabilitation of Bruce A Unit 1 and Unit 2 that will extend the in-service tile of these units by at least 25 years. Replacement of the Steam Generators (eight in each unit) is required; this work was awarded to SNC-Lavalin Nuclear (SLN). The existing steam drums (which house the steam separation and drying equipment) will be retained. Unit 2 is scheduled to be synchronized with the grid in 2009, followed by Unit 1 in 2009. Each Bruce A unit has two steam generating assemblies, one located above and to each end of the reactor. Each steam generating assembly consists of a horizontal cylindrical steam drum and four vertical Steam Generators. The vertical Steam Generators connect to individual nozzles that are located on the underside of the Steam Drum (SD). The steam drums are located in concrete shielding structures (steam drum enclosures). The lower sections of the Steam Generators penetrate the top of the reactor vaults: the containment pressure boundary is established by bellows assemblies that connect between the reactor vault roof slab and the Steam Generators. Each Steam Generators is supported from he bottom by a trapeze that is suspended from the reactor vault top structure. The Steam Generator Replacement (SGR) methodology developed by SLN for Unit 1

Effects of simultaneously elevated temperature and CO2 levels on Nicotiana benthamiana and its infection by different positive-sense RNA viruses are cumulative and virus type-specific.

Science.gov (United States)

Del Toro, Francisco J; Rakhshandehroo, Farshad; Larruy, Beatriz; Aguilar, Emmanuel; Tenllado, Francisco; Canto, Tomás

2017-11-01

We have studied how simultaneously elevated temperature and CO 2 levels [climate change-related conditions (CCC) of 30°C, 970 parts-per-million (ppm) of CO 2 vs. standard conditions (SC) of 25°C, ~ 405ppm CO 2 ] affect physiochemical properties of Nicotiana benthamiana leaves, and also its infection by several positive-sense RNA viruses. In previous works we had studied effects of elevated temperature, CO 2 levels separately. Under CCC, leaves of healthy plants almost doubled their area relative to SC but contained less protein/unit-of-area, similarly to what we had found under conditions of elevated CO 2 alone. CCC also affected the sizes/numbers of different foliar cell types differently. Under CCC, infection outcomes in titers and symptoms were virus type-specific, broadly similar to those observed under elevated temperature alone. Under either condition, infections did not significantly alter the protein content of leaf discs. Therefore, effects of elevated temperature and CO 2 combined on properties of the pathosystems studied were overall cumulative. Copyright © 2017 Elsevier Inc. All rights reserved.

Reactor container

International Nuclear Information System (INIS)

Hidaka, Masataka; Hatamiya, Shigeo; Kawasaki, Terufumi; Fukui, Toru; Suzuki, Hiroaki; Kataoka, Yoshiyuki; Kawabe, Ryuhei; Murase, Michio; Naito, Masanori.

1990-01-01

In order to suppress the pressure elevation in a reactor container due to high temperature and high pressure steams jetted out upon pipeway rupture accidents in the reactor container, the steams are introduced to a pressure suppression chamber for condensating them in stored coolants. However, the ability for suppressing the pressure elevation and steam coagulation are deteriorated due to the presence of inactive incondensible gases. Then, there are disposed a vent channel for introducing the steams in a dry well to a pressure suppression chamber in the reactor pressure vessel, a closed space disposed at the position lower than a usual liquid level, a first channel having an inlet in the pressure suppression chamber and an exit in the closed space and a second means connected by way of a backflow checking means for preventing the flow directing to the closed space. The first paths are present by plurality, a portion of which constitutes a syphon. The incondensible gases and the steams are discharged to the dry well at high pressure by using the difference of the water head for a long cooling time after the pipeway rupture accident. Then, safety can be improved without using dynamic equipments as driving source. (N.H.)

Present status of nuclear containments in Korea

International Nuclear Information System (INIS)

Park, Jihong; Hong, Jaekeun; Lee, Byunghoon; Son, Youngho

2007-01-01

Since the first nuclear power plant in Korea, Kori unit no.1, was started in commercial service in 1978, 20 units including Kori unit no.1 have been operated and maintained until now in Korea. Recently several units were started to be constructed and also, additionally more than 4 units were planned to be constructed in the near future. The importance of nuclear containments has been always one of the hottest issues for the safety and protection of nuclear power plants until now. At the beginning of nuclear power plants construction in Korea, several typed nuclear containment systems were adopted. For those reasons, various codes, standards, and inspection technologies are applied to nuclear containment systems differently. In this study, the status of inservice inspection performed for the safety and maintenance of nuclear containments in Korea was researched. Overall nuclear containment systems and inspections performed up to recently in Korea including trends, inspection items, periods, and regulations were described briefly. (author)

Assessment on the Reactor Containment Cooling Capability of Kori Unit 1 Under LOCA Conditions with Loss of Offsite Power

International Nuclear Information System (INIS)

Lee, Jin Yong; Park, Jong Woon; Kim, Hyeong Taek

2006-01-01

The fan cooler system is designed to remove heat from containment under postulated accident conditions. During a postulated LOCA concurrent with a Loss of Offsite Power (LOOP), the Component Cooling Water (CCW) pumps that supply cooling water to the fan cooler and the fan that supplies containment air to the fan cooler will temporarily lose power. Then, the high temperature steam in the containment atmosphere will pass over the fan cooler tubing without forced cooling water flow. In that case, boiling may occur in the fan cooler tubes causing steam bubbles to form and pass into the attached CCW piping creating steam voids. Prior to the CCW pumps restart, the presence of steam and subcooled water can induce the potential for water hammer. As the CCW pumps restart, the accumulated steam condenses and the pumped water can produce a water hammer when the void closes. The hydrodynamic loads caused by such a water hammer event could challenge the integrity and the function of the fan cooler and associated CCW system. With respect to this phenomena, the United States Nuclear Regulatory Commission (USNRC) issued the Generic Letter (GL) 96-06, which requests an assessment of the possibility of boiling and water hammer in the cooling water system. The objectives of this study are to develop a analysis method for predicting the thermal hydraulic status of containment fan cooler and then to assess the containment fan cooler of Kori Unit 1 using the developed model under a LOCA with LOOP

Structural review of the Palisades Nuclear Power Plant Unit 1 containment structure under combined loads for the Systematic Evaluation Program

International Nuclear Information System (INIS)

Liaw, C.Y.; Debeling, A.; Tsai, N.C.

1981-12-01

A structural reassessment of the containment structure of the Palisades Nuclear Power Plant Unit 1 was performed for the Nuclear Regulatory Commission as part of the Systematic Evaluation Program. Conclusions about the ability of the containment structure to withstand the Abnormal/Extreme Environment are presented. The reassessment focused mainly on the overall structural integrity of the containment building for the Abnormal/Extreme Environment. In this case, the Abnormal Environmental condition is caused by the worst case of either a Loss-of-Coolant Accident or a main steam line break. The Extreme Environmental condition is the Safe Shutdown Earthquake

Design of radial reinforcement for prestressed concrete containments

Energy Technology Data Exchange (ETDEWEB)

Wang, Shen, E-mail: swang@bechtel.com [Bechtel Power Corporation, 5275 Westview Drive, BP2-2C3, Frederick, MD 21703 (United States); Munshi, Javeed A., E-mail: jamunshi@bechtel.com [Bechtel Power Corporation, 5275 Westview Drive, BP2-2C3, Frederick, MD 21703 (United States)

2013-02-15

Highlights: ► A rigorous formulae is proposed to calculate radial stress within prestressed concrete containments. ► The proposed method is validated by finite element analysis in an illustrative practical example. ► A partially prestressed condition is more critical than a fully prestressed condition for radial tension. ► Practical design consideration is provided for detailing of radial reinforcement. -- Abstract: Nuclear containments are critical components for safety of nuclear power plants. Failure can result in catastrophic safety consequences as a result of leakage of radiation. Prestressed concrete containments have been used in large nuclear power plants with significant design internal pressure. These containments are generally reinforced with prestressing tendons in the circumferential (hoop) and meridional (vertical) directions. The curvature effect of the tendons introduces radial tensile stresses in the concrete shell which are generally neglected in the design of such structures. It is assumed that such tensile radial stresses are small as such no radial reinforcement is provided for this purpose. But recent instances of significant delaminations in Crystal River Unit 3 in Florida have elevated the need for reevaluation of the radial tension issue in prestressed containment. Note that currently there are no well accepted industry standards for design and detailing of radial reinforcement. This paper discusses the issue of radial tension in prestressed cylindrical and dome shaped structures and proposes formulae to calculate radial stresses. A practical example is presented to illustrate the use of the proposed method which is then verified by using state of art finite element analysis. This paper also provides some practical design consideration for detailing of radial reinforcement in prestressed containments.

Steam generator replacement in Bruce A Unit 1 and Unit 2

International Nuclear Information System (INIS)

Hart, R.S.

2006-01-01

The Bruce A Generating Station consists of four 900 MW class CANDU units. The reactor and Primary Heat Transport System for each Unit are housed within a reinforced concrete reactor vault. A large duct running below the reactor vaults accommodates the shared fuel handling system, and connects the four reactor vaults to the vacuum building. The reactor vaults, fuelling system duct and the vacuum building constitute the station vacuum containment system. Bruce A Unit 2 was shut down in 1995 and Bruce A Units 1, 3 and 4 were shutdown in 1997. Bruce A Units 3 and 4 were returned to service in late 2003 and are currently operating. Units 1 and 2 remain out of service. Bruce Power is currently undertaking a major rehabilitation of Bruce A Unit 1 and Units 2 that will extend the in-service life of these units by at least 25 years. Replacement of the Steam Generators (eight in each unit) is required; this work was awarded to SNC-Lavalin Nuclear (SLN). The existing steam drums (which house the steam separation and drying equipment) will be retained. Unit 2 is scheduled to be synchronized with the grid in 2009, followed by Unit 1 in 2009. Each Bruce A unit has two steam generating assemblies, one located above and to each end of the reactor. Each steam generating assembly consists of a horizontal cylindrical steam drum and four vertical Steam Generators. The vertical Steam Generators connect to individual nozzles that are located on the underside of the Steam Drum (SD). The steam drums are located in concrete shielding structures (steam drum enclosures). The lower sections of the Steam Generators penetrate the top of the reactor vaults: the containment pressure boundary is established by bellows assemblies that connect between the reactor vault roof slab and the Steam Generators. Each Steam Generators is supported from the bottom by a trapeze that is suspended from the reactor vault top structure. The Steam Generator Replacement (SGR) methodology developed by SLN for Unit 1

USGS Elevation Contours Overlay Map Service from The National Map

Data.gov (United States)

U.S. Geological Survey, Department of the Interior — The USGS Elevation Contours service from The National Map (TNM) consists of contours generated for the conterminous United States from 1- and 1/3 arc-second...

Global Land One-kilometer Base Elevation (GLOBE) v.1

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — GLOBE is a project to develop the best available 30-arc-second (nominally 1 kilometer) global digital elevation data set. This version of GLOBE contains data from 11...

Global patterns of protection of elevational gradients in mountain ranges.

Science.gov (United States)

Elsen, Paul R; Monahan, William B; Merenlender, Adina M

2018-05-21

Protected areas (PAs) that span elevational gradients enhance protection for taxonomic and phylogenetic diversity and facilitate species range shifts under climate change. We quantified the global protection of elevational gradients by analyzing the elevational distributions of 44,155 PAs in 1,010 mountain ranges using the highest resolution digital elevation models available. We show that, on average, mountain ranges in Africa and Asia have the lowest elevational protection, ranges in Europe and South America have intermediate elevational protection, and ranges in North America and Oceania have the highest elevational protection. We use the Convention on Biological Diversity's Aichi Target 11 to assess the proportion of elevational gradients meeting the 17% suggested minimum target and examine how different protection categories contribute to elevational protection. When considering only strict PAs [International Union for Conservation of Nature (IUCN) categories I-IV, n = 24,706], nearly 40% of ranges do not contain any PAs, roughly half fail to meet the 17% target at any elevation, and ∼75% fail to meet the target throughout ≥50% of the elevational gradient. Observed elevational protection is well below optimal, and frequently below a null model of elevational protection. Including less stringent PAs (IUCN categories V-VI and nondesignated PAs, n = 19,449) significantly enhances elevational protection for most continents, but several highly biodiverse ranges require new or expanded PAs to increase elevational protection. Ensuring conservation outcomes for PAs with lower IUCN designations as well as strategically placing PAs to better represent and connect elevational gradients will enhance ecological representation and facilitate species range shifts under climate change. Copyright © 2018 the Author(s). Published by PNAS.

Fingerprinting desmosine-containing elastin peptides

DEFF Research Database (Denmark)

Schräder, Christoph U; Heinz, Andrea; Majovsky, Petra

2015-01-01

, and DES-/IDES-containing peptides to determine characteristic product ions. It was found that all investigated compounds yielded the same product ion clusters at elevated collision energies. Elemental composition determination using the exact masses of these ions revealed molecular formulas of the type Cx...

Bucket elevator type continuous unloader; Basket elevator gata renzokushiki anroda

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-04-20

This unloader was delivered to Wakayama branch of Sumikin Butsuryu in the site of Wakayama steel plant of Sumitomo Metal Industries Ltd. for landing sub-materials for ironworks. Main specifications: (1) Capacity: 400t/h for limestone, 280t/h for gypsum, (2) Kinds of ships: 5,000DWT maximum, (3) Boom swing radius: 20m. Features: (1) Simple light-weight unloader for not large ships for main materials but small coastal service ships which works with not swing motion but only traveling and normal-directional motion of the under structure of a bucket elevator unit, (2) Various useful functions such as ground conveyance, truck loading, back yard stacking and back yard shipment for handling of various sub-materials. (translated by NEDO)

Design rule for fatigue of welded joints in elevated-temperature nuclear components

International Nuclear Information System (INIS)

O'Connor, D.G.; Corum, J.M.

1986-01-01

Elevated-temperature weldment fatigue failures have occurred in several operating liquid-metal reactor plants. Yet, ASME Code Case N-47, which governs the design of such plants in the United States, does not currently address the Code Subgroup on Elevated Temperature Design recently proposed a fatigue strength reduction factor for austenitic and ferritic steel weldments. The factor is based on a variety of weld metal and weldment fatigue data generated in the United States, Europe, and Japan. This paper describes the factor and its bases, and it presents the results of confirmatory fatigue tests conducted at Oak Ridge National Laboratory on 316 stainless steel tubes with axial and circumferential welds of 16-8-2 filler metal. These test results confirm the suitability of the design factor, and they support the premise that the metallurgical notch effect produced by yield strength variations across a weldment is largely responsible for the observed elevated-temperature fatigue strength reduction

2013 NOAA Topographic Lidar: US Virgin Islands Digital Elevation Models (DEMs)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The United States Virgin Islands Topographic LiDAR Task Order involved collecting and delivering topographic elevation point data derived from multiple return light...

Elevated Lipoprotein(A Impairs Platelet Radiolabeling Yield

Directory of Open Access Journals (Sweden)

Susanne Granegger

2015-02-01

Full Text Available Objectives: Platelet radiolabeling in clinical routine usually results in labeling efficiencies (LE above 80%. A variety of risk factors and clinical conditions are known to impair platelet labeling yield, among them elevated triglycerides and low-density lipoproteins. The potential influence of lipoprotein(a (Lp(a, an atherogenic lipoprotein particle containing a kringle subunit, which is widely found in the proteins of fibrinolysis pathway, has never been studied. Normal Lp(a levels range below 30 mg/ dl. The exact prevalence of elevated Lp(a is unknown, most likely ranging below 10%. Even more rare is an isolated elevation despite an otherwise normal lipoprotein profile. Methods: We examined the role of isolated elevated Lp(a (> 50 mg/dl, ranging up to 440 mg/dl compared to patients with normal lipid profile. Platelets were radiolabeled with in-111-oxine at 37 °C for 5 minutes using ISORBE-consensus methodology. Results: The findings indicate that already at levels below 100 mg/dl Lp(a decreases LE. LE assessment after cross-incubation of hyper-Lp(a platelets with normal Lp(a plasma and vice versa reveals that platelets rather than the plasmatic environment are responsible for the deterioration of labeling yield. This behavior already has been reported for elevated low-density lipoproteins. Apparently, the quantitative influence of LDL and Lp(a/mg is comparable. Plotting the sum of LDL and Lp(a versus LE reveals a clear significant negative correlation. Conclusion: As extremely elevated Lp(a, particularly above 150 mg/dl, may significantly impair labeling results. We therefore recommend to include extremely elevated Lp(a into the list of parameters, which should be known before performing radiolabeling of human platelets.

Properties of PHA bi-, ter-, and quarter-polymers containing 4-hydroxybutyrate monomer units.

Science.gov (United States)

Zhila, Natalia; Shishatskaya, Ekaterina

2018-05-01

The present study investigates physicochemical, mechanical, and biological properties of polyhydroxyalkanoate (PHA) copolymers containing 4-hydroxybutyrate (4HB) synthesized in Cupriavidus eutrophus B10646 culture. In poly(3-hydroxybutyrate/4-hydroxybutyrate) [P(3HB/4HB)] bipolymers, 4HB varied between 10.4 and 75.0 mol%; in poly(3-hydroxybutyrate/3-hydroxyvalerate/4-hydroxybutyrate) terpolymers, 4HB constituted 28.7-55.6 mol%; and in poly(3-hydroxybutyrate/3-hydroxyvalerate/4-hydroxybutyrate/3-hydroxyhexanoate) quaterpolymers, 4HB varied between 9.3 and 13.3 mol%. The degree of crystallinity of P(3HB/4HB) copolymers decreased consistently with an increase in 4HB content, reaching 38%. The incorporation of 3-hydroxyvalerate and 3-hydroxyhexanoate into copolymers enhanced that effect. The effect of 4HB monomer units on temperature properties of copolymers was exhibited as lowering of the melting temperature and crystallization temperature, which improved the processing-related properties of the copolymers. All copolymers containing 4HB showed enhanced elongation at break compared to poly(3-hydroxybutyrate). Polymer films prepared from PHAs with different chemical composition had similar microstructure and porosity and had no toxic effect on mouse fibroblast NIH 3 T3 cells, proving their high biocompatibility. Copyright © 2018 Elsevier B.V. All rights reserved.

Silsesquioxane-based hybrid nanocomposites with methacrylate units containing titania and/or silver nanoparticles as antibacterial/antifungal coatings for monumental stones

Energy Technology Data Exchange (ETDEWEB)

Aflori, Magdalena [“Petru Poni” Institute of Macromolecular Chemistry, 41A Grigore Ghica Voda Alley, 700487 Iasi (Romania); Simionescu, Bogdana [“Petru Poni” Institute of Macromolecular Chemistry, 41A Grigore Ghica Voda Alley, 700487 Iasi (Romania); “Costin D. Nenitescu” Centre of Organic Chemistry, 202B Splaiul Independentei, 7114 Bucharest (Romania); Bordianu, Irina-Elena; Sacarescu, Liviu; Varganici, Cristian-Dragos; Doroftei, Florica; Nicolescu, Alina [“Petru Poni” Institute of Macromolecular Chemistry, 41A Grigore Ghica Voda Alley, 700487 Iasi (Romania); Olaru, Mihaela, E-mail: olaruma@icmpp.ro [“Petru Poni” Institute of Macromolecular Chemistry, 41A Grigore Ghica Voda Alley, 700487 Iasi (Romania)

2013-11-20

Highlights: • Synthesis of nanocomposites with noble metals having high antibacterial efficiency. • Silver nanoparticles antibacterial activity for monumental stone conservation. • A high antibacterial activity while assuring good stone protection. -- Abstract: The present paper reports on the evaluation of two silsesquioxane-based hybrid nanocomposites with methacrylate units containing titania and/or silver nanoparticles aimed as antibacterial coatings for monumental stones. Sol–gel reaction of titanium isopropoxide and/or 3-(trimethoxysilyl)propyl methacrylate, in the presence of silver nitrate and a primary amine surfactant, yielded new types of hybrid nanocomposites with high antibacterial/antifungal efficacy. Different polymer behaviours regarding a frequently used monumental stone originating from Romania were evidenced through Fourier-transform infrared (FTIR) spectroscopy and powder X-ray diffraction (PXRD) technique. Conclusions regarding the stones acid-resistant character and lower influence of salt weathering on its durability, as well as a better protective coating containing titania units were revealed.

Silsesquioxane-based hybrid nanocomposites with methacrylate units containing titania and/or silver nanoparticles as antibacterial/antifungal coatings for monumental stones

International Nuclear Information System (INIS)

Aflori, Magdalena; Simionescu, Bogdana; Bordianu, Irina-Elena; Sacarescu, Liviu; Varganici, Cristian-Dragos; Doroftei, Florica; Nicolescu, Alina; Olaru, Mihaela

2013-01-01

Highlights: • Synthesis of nanocomposites with noble metals having high antibacterial efficiency. • Silver nanoparticles antibacterial activity for monumental stone conservation. • A high antibacterial activity while assuring good stone protection. -- Abstract: The present paper reports on the evaluation of two silsesquioxane-based hybrid nanocomposites with methacrylate units containing titania and/or silver nanoparticles aimed as antibacterial coatings for monumental stones. Sol–gel reaction of titanium isopropoxide and/or 3-(trimethoxysilyl)propyl methacrylate, in the presence of silver nitrate and a primary amine surfactant, yielded new types of hybrid nanocomposites with high antibacterial/antifungal efficacy. Different polymer behaviours regarding a frequently used monumental stone originating from Romania were evidenced through Fourier-transform infrared (FTIR) spectroscopy and powder X-ray diffraction (PXRD) technique. Conclusions regarding the stones acid-resistant character and lower influence of salt weathering on its durability, as well as a better protective coating containing titania units were revealed

Evaluation of Elevated Tritium Levels in Groundwater Downgradient from the 618-11 Burial Ground Phase I Investigations

Energy Technology Data Exchange (ETDEWEB)

Dresel, P.E.; Smith, R.M.; Williams, B.A.; Thompson, C.J.; Evans, J.C.; Hulstrom, L.C.

2000-05-01

This report describes the results of the preliminary investigation of elevated tritium in groundwater discovered near the 618-11 burial ground, located in the eastern part of the Hanford Site. Tritium in one well downgradient of the burial ground was detected at levels up to 8,140,000 pCi/L. The 618-11 burial ground received a variety of radioactive waste from the 300 Area between 1962 and 1967. The burial ground covers 3.5 hectare (8.6 acre) and contains trenches, large diameter caissons, and vertical pipe storage units. The burial ground was stabilized with a native sediment covering. The Energy Northwest reactor complex was constructed immediately east of the burial ground.

Evaluation of Elevated Tritium Levels in Groundwater Downgradient from the 618-11 Burial Ground Phase I Investigations

International Nuclear Information System (INIS)

Dresel, P.E.; Smith, R.M.; Williams, B.A.; Thompson, C.J.; Evans, J.C.; Hulstrom, L.C.

2000-01-01

This report describes the results of the preliminary investigation of elevated tritium in groundwater discovered near the 618-11 burial ground, located in the eastern part of the Hanford Site. Tritium in one well downgradient of the burial ground was detected at levels up to 8,140,000 pCi/L. The 618-11 burial ground received a variety of radioactive waste from the 300 Area between 1962 and 1967. The burial ground covers 3.5 hectare (8.6 acre) and contains trenches, large diameter caissons, and vertical pipe storage units. The burial ground was stabilized with a native sediment covering. The Energy Northwest reactor complex was constructed immediately east of the burial ground

Aggregation and C dynamics along an elevation gradient in carbonate-containing grassland soils of the Alps

Science.gov (United States)

Garcia-Franco, Noelia; Wiesmeier, Martin; Kiese, Ralf; Dannenmann, Michael; Wolf, Benjamin; Zistl-Schlingmann, Marcus; Kögel-Knabner, Ingrid

2017-04-01

C sequestration in mountainous grassland soils is regulated by physical, chemical and biological soil process. An improved knowledge of the relationship between these stabilization mechanisms is decisive to recommend the best management practices for climate change mitigation. In this regard, the identification of a successful indicator of soil structural improvement and C sequestration in mountainous grassland soils is necessary. Alpine and pre-alpine grassland soils in Bavaria represent a good example for mountainous grassland soils faced with climate change. We sampled grassland soils of the northern limestone alps in Bavaria along an elevation gradient from 550 to 1300 m above sea level. We analyzed C dynamics by a comparative analysis of the distribution of C according to aggregate size classes: large-macroaggregates (> 2000 µm), small-macroaggregates (250-2000 µm), microaggregates (63-250 µm), silt plus clay particles (soil. Our preliminary results showed higher C content and changed water-stable aggregate distribution in the high elevation sites compared to lower elevations. Magnesium carbonate seem to play an important role in stabilizing macroaggregates formed from fresh OM. In addition, the isolation of occluded microaggregates within macroaggregates will help us to improve our understanding on the effects of climate change on soil structure and on the sensitivity of different C stabilization mechanisms present in mountainous soils.

A Preliminary Study on the Containment Integrity following BIT Removal for Kori NPP Unit 3,4

Energy Technology Data Exchange (ETDEWEB)

Song, Dong Soo; Byun, Choong Sup [KEPRI, Nuclear Power Generation Laboratory, Daejeon (Korea, Republic of); Jo, Jong Young [ENERGEO Inc., Sungnam (Korea, Republic of)

2008-05-15

The Boron Injection Tank (BIT) is to provide high concentrated boric acid to the reactor in order to mitigate the consequences of postulated Main Steam Line Break accidents (MSLB). Although BIT plays an important role in mitigating the accident, high concentration of 20,000ppm causes valve leakage, pipe clog, precipitation and continuous heat tracing have to be provided. This paper is for the feasibility study of containment integrity using CONTEMPT code for BIT removal of Kori Nuclear Power Plant (NPP) Unit 3, 4.

A Preliminary Study on the Containment Integrity following BIT Removal for Kori NPP Unit 3,4

International Nuclear Information System (INIS)

Song, Dong Soo; Byun, Choong Sup; Jo, Jong Young

2008-01-01

The Boron Injection Tank (BIT) is to provide high concentrated boric acid to the reactor in order to mitigate the consequences of postulated Main Steam Line Break accidents (MSLB). Although BIT plays an important role in mitigating the accident, high concentration of 20,000ppm causes valve leakage, pipe clog, precipitation and continuous heat tracing have to be provided. This paper is for the feasibility study of containment integrity using CONTEMPT code for BIT removal of Kori Nuclear Power Plant (NPP) Unit 3, 4

Anomalous elevated radiocarbon measurements of PM2.5

International Nuclear Information System (INIS)

Buchholz, Bruce A.; Fallon, Stewart J.; Zermeño, Paula; Bench, Graham; Schichtel, Bret A.

2013-01-01

Two-component models are often used to determine the contributions made by fossil fuel and natural sources of carbon in airborne particulate matter (PM). The models reduce thousands of actual sources to two end members based on isotopic signature. Combustion of fossil fuels produces PM free of carbon-14 ( 14 C). Wood or charcoal smoke, restaurant fryer emissions, and natural emissions from plants produce PM with the contemporary concentration of 14 C approximately 1.2 × 10 −1214 C/C. Such data can be used to estimate the relative contributions of fossil fuels and biogenic aerosols to the total aerosol loading and radiocarbon analysis is becoming a popular source apportionment method. Emissions from incinerators combusting medical or biological wastes containing tracer 14 C can skew the 14 C/C ratio of PM, however, so critical analysis of sampling sites for possible sources of elevated PM needs to be completed prior to embarking on sampling campaigns. Results are presented for two ambient monitoring sites in different areas of the United States where 14 C contamination is apparent. Our experience suggests that such contamination is uncommon but is also not rare (∼10%) for PM sampling sites.

MILA Antenna Control Unit Replacement Project

Science.gov (United States)

Bresette, Jeremy

2007-01-01

The Air to Ground Subsystem (AGS) Antenna Control Units at the MILA Ground Network Tracking Station are at end-of-life and are being replaced. AGS consists of two antennas at MILA (Quad-Helix and Teltrac). Software was taken from the existing Subsystem Controller and modified for the Antenna Control Unit (ACU). The software is capable of receiving and sending commands to and from the ACU. Moving the azimuth clockwise, counterclockwise, moving the elevation up or down, turning servo power on and off, and inputting azimuth and elevation angles are commands that the antenna can receive.

Assessment of the Internal Pressure Fragility of the Hanul NPP Units 3 and 4 Containment Building Using a Nonlinear Finite Element Analysis

Energy Technology Data Exchange (ETDEWEB)

Park, Hyung Kui; Hahm, Dea Gi; Choi, In Kil [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-10-15

The sensitivity of the concrete strength is relatively higher compared to that of the steel strength. According to changes in the structure of the material, about 6-10% ultimate internal pressure differences occurred. Thirty sets of an FE model considering the material uncertainty of concrete and steel were composed for the internal pressure fragility assessment. From the internal pressure fragility assessment of the target containment building, the median capacity of liner leakage is estimated to be 116 psi. As can be seen from the Fukushima nuclear power plant accident, the containment building is the final protecting shield to prevent radiation leakage. Thus, a structural soundness evaluation for the containment pressure loads owing to a severe accident is very important. Recently, a probabilistic safety assessment has been commonly used to take into account the possible factors of uncertainty in a structural system. An assessment of the internal pressure fragility of the CANDU type containment buildings considering the correlation of structural material variables, and an assessment of the internal pressure fragility of the CANDU type containment buildings using a nonlinear finite element analysis, were also performed. However, for PWR type containment buildings, a fragility assessment has not been performed yet using a nonlinear finite element model (FEM) analysis. In this study, for the Hanul NPP units 3 and 4 containment building, the internal pressure fragility assessment was established using an FEM analysis. To do this, a three-dimensional finite element model, material property values, and a sensitive analysis were developed. A nonlinear finite element analysis of the Hanul NPP units 3 and 4 containment building was performed for a material sensitivity analysis and internal pressure fragility assessment.

Assessment of the Internal Pressure Fragility of the Hanul NPP Units 3 and 4 Containment Building Using a Nonlinear Finite Element Analysis

International Nuclear Information System (INIS)

Park, Hyung Kui; Hahm, Dea Gi; Choi, In Kil

2013-01-01

The sensitivity of the concrete strength is relatively higher compared to that of the steel strength. According to changes in the structure of the material, about 6-10% ultimate internal pressure differences occurred. Thirty sets of an FE model considering the material uncertainty of concrete and steel were composed for the internal pressure fragility assessment. From the internal pressure fragility assessment of the target containment building, the median capacity of liner leakage is estimated to be 116 psi. As can be seen from the Fukushima nuclear power plant accident, the containment building is the final protecting shield to prevent radiation leakage. Thus, a structural soundness evaluation for the containment pressure loads owing to a severe accident is very important. Recently, a probabilistic safety assessment has been commonly used to take into account the possible factors of uncertainty in a structural system. An assessment of the internal pressure fragility of the CANDU type containment buildings considering the correlation of structural material variables, and an assessment of the internal pressure fragility of the CANDU type containment buildings using a nonlinear finite element analysis, were also performed. However, for PWR type containment buildings, a fragility assessment has not been performed yet using a nonlinear finite element model (FEM) analysis. In this study, for the Hanul NPP units 3 and 4 containment building, the internal pressure fragility assessment was established using an FEM analysis. To do this, a three-dimensional finite element model, material property values, and a sensitive analysis were developed. A nonlinear finite element analysis of the Hanul NPP units 3 and 4 containment building was performed for a material sensitivity analysis and internal pressure fragility assessment

MOBIL CONTAINER UNIT FOR SEWAGE SLUDGE UTILIZATION FROM SMALL AND MEDIUM WASTWATER TREATMENT PLANTS

Directory of Open Access Journals (Sweden)

Stanisław Ledakowicz

2016-06-01

Full Text Available The most wastewater treatment plants in Poland are small and medium plants of flow capacity below 1000 m3/d. These plants are not able to build sludge incineration plants and the transportation costs to the nearest plants increase the total costs of wastewater treatment. Polish company Metal Expert together with the French company ETIA and Lodz University of Technology proposed mobile unit for integrated drying and pyrolysis of sewage sludge in a pilot bench scale with capacity of 100 kg/h of dewatered sludge. The pilot plant was mounted in a typical mobile container which could provide service to small and medium wastewater treatment plants offering thermal processing of sewage sludge. This unit consists of KENKI contact dryer and „Spirajoule”® pyrolyser supplied with electricity utilizing the Joule effect, and a boiler, wherein the pyrolysis gases and volatile products are burned producing steam sent to the contact dryer. The bio-char produced during sludge pyrolysis could be utilized for agriculture purposes. During preliminary experiments and short-term exploitation of the unit at Elbląg Wastewater Treatment Plant the obtained results allowed us to make a mass and energy balance depended on the process conditions in the pyrolysis temperature range of 400÷800 °C. Based on the obtained results a calculator was created in the Excel , which enables assessment of pyrolysis products content and making mass and energy balances depended on process parameters such as initial moisture of sludge, pyrolysis temperature and installation output.

50 CFR Table 3 to Part 226 - Hydrologic Units Containing Critical Habitat for Snake River Sockeye Salmon and Snake River...

Science.gov (United States)

2010-10-01

... Habitat for Snake River Sockeye Salmon and Snake River Spring/Summer and Fall Chinook Salmon 3 Table 3 to... Part 226—Hydrologic Units Containing Critical Habitat for Snake River Sockeye Salmon and Snake River... Snake—Asotin 17060103 17060103 17060103 Upper Grande Ronde 17060104 Wallowa 17060105 Lower Grande Ronde...

IceBridge Riegl Laser Altimeter L2 Geolocated Surface Elevation Triplets

Data.gov (United States)

National Aeronautics and Space Administration — The IceBridge Riegl Laser Altimeter L2 Geolocated Surface Elevation Triplets (ILUTP2) data set contains surface range values for Antarctica and Greenland derived...

Antioxidant activity and polyphenol and procyanidin contents of selected commercially available cocoa-containing and chocolate products in the United States.

Science.gov (United States)

Miller, Kenneth B; Stuart, David A; Smith, Nancy L; Lee, Chang Y; McHale, Nancy L; Flanagan, Judith A; Ou, Boxin; Hurst, W Jeffrey

2006-05-31

In the United States, commercially available foods, including cocoa and chocolate, are being marketed with statements referring to the level of antioxidant activity and polyphenols. For cocoa-containing foods, there has been no comprehensive survey of the content of these and other chemistries. A survey of cocoa and chocolate-containing products marketed in the United States was conducted to determine antioxidant activity and polyphenol and procyanidin contents. Commercially available samples consisted of the top market share products in each of the following six categories: natural cocoa, unsweetened baking chocolate, dark chocolate, semisweet baking chips, milk chocolate, and chocolate syrup. Composite samples were characterized using four different methods: oxygen radical absorbance capacity (ORAC), vitamin C equivalence antioxidant capacity (VCEAC), total polyphenols, and procyanidins. All composite lots were further characterized for percent nonfat cocoa solids (NFCS) and percent fat. Natural cocoas had the highest levels of antioxidant activities, total polyphenols, and procyanidins followed by baking chocolates, dark chocolates and baking chips, and finally milk chocolate and syrups. The results showed a strong linear correlation between NFCS and ORAC (R (2) = 0.9849), total polyphenols (R (2) = 0.9793), and procyanidins (R (2) = 0.946), respectively. On the basis of principal component analysis, 81.4% of the sample set was associated with NFCS, antioxidant activity, total polyphenols, and procyanidins. The results indicated that, regardless of the product category, NFCS were the primary factor contributing to the level of cocoa antioxidants in the products tested. Results further suggested that differences in cocoa bean blends and processing, with the possible exception of Dutching, are minor factors in determining the level of antioxidants in commercially available cocoa-containing products in the United States.

Coastal sediment elevation change following anthropogenic mangrove clearing

Science.gov (United States)

Hayden, Heather L.; Granek, Elise F.

2015-11-01

Coastal mangrove forests along tropical shorelines serve as an important interface between land and sea. They provide a physical buffer protecting the coastline from erosion and act as sediment "traps" catching terrestrial sediment, thus preventing smothering of subtidal coral reefs. Coastal development that removes mangrove habitat may impact adjacent nearshore coral reefs through sedimentation and nutrient loading. We examined differences in sediment elevation change between patches of open-coast intact and anthropogenically cleared red mangroves (Rhizophora mangle) on the east side of Turneffe Atoll, Belize, to quantify changes following mangrove clearing. Samples were collected over a 24 month period at five study sites, each containing paired intact (+mangrove) and cleared (-mangrove) plots. Five sediment elevation pins were deployed in each plot: behind areas cleared of mangroves (-mangrove) and behind adjacent intact mangroves (+mangrove). Sediment elevation increased at intact mangrove sites (M = +3.83 mm, SE = 0.95) whereas cleared mangrove areas suffered elevation loss (M = -7.30 mm, SE = 3.38). Mangroves inshore of partial or continuous gaps in the adjacent fringing reefs had higher rates of elevation loss (M = -15.05 mm) than mangroves inshore of continuous fringing reefs (M = -1.90 mm). Our findings provide information on potential effects of mangrove clearing and the role of offshore habitat characteristics on coastal sediment trapping and maintenance of sediment elevation by mangroves. With implications for coastline capacity to adjust to sea level rise, these findings are relevant to management of coastal fringing mangrove forests across the Caribbean.

Helical type vacuum container

International Nuclear Information System (INIS)

Owada, Kimio.

1989-01-01

Helical type vacuum containers in the prior art lack in considerations for thermal expansion stresses to helical coils, and there is a possibility of coil ruptures. The object of the present invention is to avoid the rupture of helical coils wound around the outer surface of a vacuum container against heat expansion if any. That is, bellows or heat expansion absorbing means are disposed to a cross section of a helical type vacuum container. With such a constitution, thermal expansion of helical coils per se due to temperature elevation of the coils during electric supply can be absorbed by expansion of the bellows or absorption of the heat expansion absorbing means. Further, this can be attained by arranging shear pins in the direction perpendicular to the bellows axis so that the bellows are not distorted when the helical coils are wound around the helical type vacuum container. (I.S.)

Methods, means and results from containment leakage decrease in unit 2 at Kozloduy NPP with international participation

Energy Technology Data Exchange (ETDEWEB)

Demireva, E; Grigorov, D; Balabanov, E [Energoproekt, Sofia (Bulgaria)

1996-12-31

A study of the Kozloduy NPP Unit 2 containment improvement has been carried out. The following objectives are identified: to assess confinement tightness (local tests); to improve tightness; to perform the most urgent repair works; to develop global test procedures including leak tightness at nominal and reduced pressure, structural integrity test and venting flaps reliability test. Nine groups of potential leakage paths have been determined. The ventilation system has been found as the major source of expected leakage having 60 penetrations with size above 250 mm. Proposed modifications of the ventilation system include reduction of the number of inflow and suction valves, replacement of some valves with a better quality ones and installation of isolating valves. It is planned to transfer the experience and results of this study to the other WWER-440 units. 1 ref.

Methods, means and results from containment leakage decrease in unit 2 at Kozloduy NPP with international participation

International Nuclear Information System (INIS)

Demireva, E.; Grigorov, D.; Balabanov, E.

1995-01-01

A study of the Kozloduy NPP Unit 2 containment improvement has been carried out. The following objectives are identified: to assess confinement tightness (local tests); to improve tightness; to perform the most urgent repair works; to develop global test procedures including leak tightness at nominal and reduced pressure, structural integrity test and venting flaps reliability test. Nine groups of potential leakage paths have been determined. The ventilation system has been found as the major source of expected leakage having 60 penetrations with size above 250 mm. Proposed modifications of the ventilation system include reduction of the number of inflow and suction valves, replacement of some valves with a better quality ones and installation of isolating valves. It is planned to transfer the experience and results of this study to the other WWER-440 units. 1 ref

Properties of concrete containing different type of waste materials as aggregate replacement exposed to elevated temperature – A review

Science.gov (United States)

Ghadzali, N. S.; Ibrahim, M. H. W.; Sani, M. S. H. Mohd; Jamaludin, N.; Desa, M. S. M.; Misri, Z.

2018-04-01

Concrete is the chief material of construction and it is non-combustible in nature. However, the exposure to the high temperature such as fire can lead to change in the concrete properties. Due to the higher temperature, several changes in terms of mechanical properties were observed in concrete such as compressive strength, modulus of elasticity, tensile strength and durability of concrete will decrease significantly at high temperature. The exceptional fire-proof achievement of concrete is might be due to the constituent materials of concrete such as its aggregates. The extensive use of aggregate in concrete will leads to depletion of natural resources. Hence, the use of waste and other recycled and by-product material as aggregates replacements becomes a leading research. This review has been made on the utilization of waste materials in concrete and critically evaluates its effects on the concrete performances during the fire exposure. Therefore, the objective of this paper is to review the previous search work regarding the concrete containing waste material as aggregates replacement when exposed to elevated temperature and come up with different design recommendations to improve the fire resistance of structures.

Green Degree Comprehensive Evaluation of Elevator Based on Fuzzy Analytic Hierarchy Process

Directory of Open Access Journals (Sweden)

Lizhen

2015-01-01

Full Text Available The green design of the elevator has many characteristics which contains many factors and the combination of qualitative and quantitative. In view of the fuzzy problem of evaluation index information, fuzzy analytic hierarchy process and fuzzy comprehensive evaluation model are combined to evaluate the green degree of elevator. In this method, the weights of the indexes are calculated by using the fuzzy analytic hierarchy process and the fuzzy analytic hierarchy process is used to calculate the weights of each level. The feasibility will be defined of using green degree evaluation of elevator system as an example to verify the method.

Transport processes associated with the initial elevated concentrations of Chernobyl radioactivity in surface air in the United States

International Nuclear Information System (INIS)

Larsen, R.J.; Haagenson, P.L.; Reiss, N.M.

1989-01-01

Elevated concentrations of radioactivity from the Chernobyl accident were encountered in the surface air over the United States along the east coast and in the north-west on 9 and 10 May 1986. The nearly simultaneous arrival of radioactive debris at widely separated locations resulted from different paths being taken by the debris released at different times during the course of the accident. Debris released during the explosion at the Chernobyl reactor was transported across the Arctic, within the lower troposphere, and zonally across Asia and the North Pacific Ocean, within the mid-troposphere. This debris descended into the planetary boundary layer along the east coast of the US. The descent was associated with a quasi-stationary cyclone located over the western North Atlantic Ocean. Debris that had a different composition of radioactivity was released from the damaged reactor during the week immediately following the initial explosion. This debris was then transported zonally across Asia and the North Pacific Ocean within the planetary boundary layer and lower troposphere and was swept into the north-western US. (author)

Study of ex-vessel steam explosion risk of Reactor Pit Flooding System and structural response of containment for CPR1000"+ Unit

International Nuclear Information System (INIS)

Zhang Juanhua; Chen Peng

2015-01-01

Reactor Pit Flooding System is one of the special mitigation measures for severe accident for CPR1000"+ Unit. If the In-Vessel Relocation function of Reactor Pit Flooding System is failed, there is the steam explosion risk in reactor cavity. This paper firstly adopts MC3D code to build steam explosion model in order to calculate the pressure load and impulses of steam explosion that are as the input data of containment structural response analysis. The next step is to model the containment structure and analyze the structural response by ABAQUS code. The analysis results show that the integral damage induced by steam explosion to the external containment wall is shallow, and the containment structural integrity can be maintained. The risk and damage to the containment integrity reduced by steam explosion of RPF is small, and it does not influence the design and implementation of RPF. (author)

Bellefonte primary containment structure

International Nuclear Information System (INIS)

Olyniec, J.H.

1981-01-01

Construction of the reactor building primary containment structure at the Bellefonte Nuclear Plant involved several specialized construction techniques. This two unit plant is one of the nine nuclear units at six different sites now under construction by the Tennessee Valley Authority (TVA). The post-Tensioned, cast-in-place interior steel lined containment structure is unique within TVA. Problems during construction were identified at weekly planning meetings, and options were discussed. Close coordination between craft supervisors and on-site engineering personnel drew together ''hands-on''experience and technical background. Details of the construction techniques, problems, and solutions are presented

STRUCTURE LINE DETECTION FROM LIDAR POINT CLOUDS USING TOPOLOGICAL ELEVATION ANALYSIS

Directory of Open Access Journals (Sweden)

C. Y. Lo

2012-07-01

Full Text Available Airborne LIDAR point clouds, which have considerable points on object surfaces, are essential to building modeling. In the last two decades, studies have developed different approaches to identify structure lines using two main approaches, data-driven and modeldriven. These studies have shown that automatic modeling processes depend on certain considerations, such as used thresholds, initial value, designed formulas, and predefined cues. Following the development of laser scanning systems, scanning rates have increased and can provide point clouds with higher point density. Therefore, this study proposes using topological elevation analysis (TEA to detect structure lines instead of threshold-dependent concepts and predefined constraints. This analysis contains two parts: data pre-processing and structure line detection. To preserve the original elevation information, a pseudo-grid for generating digital surface models is produced during the first part. The highest point in each grid is set as the elevation value, and its original threedimensional position is preserved. In the second part, using TEA, the structure lines are identified based on the topology of local elevation changes in two directions. Because structure lines can contain certain geometric properties, their locations have small relieves in the radial direction and steep elevation changes in the circular direction. Following the proposed approach, TEA can be used to determine 3D line information without selecting thresholds. For validation, the TEA results are compared with those of the region growing approach. The results indicate that the proposed method can produce structure lines using dense point clouds.

Results from modernization of the containment localization systems of the Kozloduy NPP units 3 and 4

International Nuclear Information System (INIS)

Sabinov, S.

2005-01-01

The improvements of the Accident Localization System (SLA) of units 3 and 4 systematically implemented by Kozloduy NPP shows an important direction for increasing the safety of NPP with WWER-440/V-230 containments. During the years Kozloduy NPP implemented a large scope of activities aimed in full resolution of all generic shortcomings identified in the original design of these containments. These activities allowed already in 2002 to justify that integrity of the containment is assured for all postulated events and the radiological consequences for all DBAs and BDBAs without core degradation are within the regulatory limits. The last phase of this modernization was oriented toward achieving the same goals in case of severe accidents by installation of systems for avoiding long term pressurization of the SG compartments and by installation of a system for keeping of negative pressure (slight vacuum) during the late phases of development of the accidents thus minimizing significantly the uncontrolled radioactive releases from the containment and assured controlled purified release of radioactivity to environment, and for elimination of conditions for H2 deflagration within the localization system. This paper summarizes the results of the whole modernization process with an emphasis of the implementation of the latest phase successfully completed by Kozloduy NPP in first quarter of 2005 which allowed the plant to demonstrate remarkable mitigation capability for a comprehensive set of very low probability severe accidents scenarios in line with the approach now being promoted for the modern design NPPs

Novel hydroxyamides and amides containing D-glucopyranose or D-fructose units: Biological assays in MCF-7 and MDST8 cell lines.

Science.gov (United States)

Carreiro, Elisabete P; Costa, Ana R; Cordeiro, Maria M; Martins, Rute; Pires, Tiago O; Saraiva, Mafalda; Antunes, Célia M; Burke, Anthony J

2016-02-01

A novel library of 15 compounds, hydroxyamides and amides containing a β-D-glucopyranose (D-Gluc) or a β-D-fructose (D-Fruc) units was designed and synthesized for antiproliferative assays in breast (MCF-7) and colon (MDST8) cancer cell lines. Twelve of them were hydroxyamides and were successfully synthesized from β-D-glucuronic acid (D-GluA). Six of these hydroxyamides which were acetylated hydroxy-β-D-glucopyranuronamide 2a-2f (1st Family) and the other six were their respective isomers, that is, hydroxy-β-D-fructuronamide 3a-3f (2nd Family), obtained by acid-base catalyzed isomerization. These compounds have the general structure, D-Gluc-C=ONH-CHR-(CH2)n-OH and D-Fruc-C=ONH-CHR-(CH2)n-OH, where R=an aromatic, alkyl or a hydrogen substituent, with n=0 or 1. Eight of these contained a chiral aminoalcohol group. Three compounds were amides containing a D-glucopyranose unit (3rd Family). SAR studies were conducted with these compounds. Antiproliferative studies showed that compound 4a, the bromo-amide containing the β-D-glucopyranose ring, potently inhibits the proliferation of the MDST8 cells. Five compounds (2e, 2f, 3d, 3e, and 3f) were shown to potently selectively inhibit the proliferation of the MCF-7 cells. Compound 4b was the only one showing inhibition in both cell lines. In general, the more active compounds were the amides and hydroxyamides containing the β-D-fructose moiety, and containing an alkyl group or hydrogen. Half-inhibitory concentrations (IC50) of between 0.01 and 10 μM, were observed. Copyright © 2015 Elsevier Ltd. All rights reserved.

The 3D Elevation Program: summary for Hawaii

Science.gov (United States)

Carswell, William J.

2016-01-01

Elevation data are essential to a broad range of applications, including forest resources management, wildlife and habitat management, national security, recreation, and many others. For the State of Hawaii, elevation data are critical for infrastructure and construction management, flood risk management, geologic resource assessment and hazard mitigation, natural resources conservation, coastal zone management, and other business uses. Today, high-density light detection and ranging (lidar) data are the primary sources for deriving elevation models and other datasets. Federal, State, Tribal, U.S. territorial, and local agencies work in partnership to (1) replace data that are older and of lower quality and (2) provide coverage where publicly accessible data do not exist. A joint goal of State and Federal partners is to acquire consistent, statewide coverage to support existing and emerging applications enabled by lidar data.The National Enhanced Elevation Assessment evaluated multiple elevation data acquisition options to determine the optimal data quality and data replacement cycle relative to cost to meet the identified requirements of the user community. The evaluation demonstrated that lidar acquisition at quality level 2 for the conterminous United States, Hawaii, and selected U.S. territories, and quality level 5 interferometric synthetic aperture radar (IfSAR) data for Alaska, all with a 6- to 10-year acquisition cycle, provided the highest benefit/cost ratios. The 3D Elevation Program (3DEP) initiative selected an 8-year acquisition cycle for the respective quality levels. 3DEP, managed by the U.S. Geological Survey, the Office of Management and Budget Circular A–16 lead agency for terrestrial elevation data, responds to the growing need for high-quality topographic data and a wide range of other three-dimensional (3D) representations of the Nation’s natural and constructed features.

Fluoride removal from double four-membered ring (D4R) units in As-synthesized Ge-containing zeolites

KAUST Repository

Liu, Xiaolong

2011-11-22

Fluoride anions can be removed from the framework of as-prepared Ge-containing zeolites ITQ-13 and ITQ-17 without modification of the crystallinity and crystal habit. By contrast to all-silica ITQ-13 for which fluoride could not get out from D4R units, F is completely removed from Ge rich zeolites, even from D4R cages. This has been explained by the relaxing effect of germanium, making F less necessary for the stabilization of the small D4R units. Si/Ge ratios are similar in as-prepared and treated zeolites, indicating that the framework composition is not affected by the removal of anions. The fluoride-free zeolites possess XRD patterns similar to those of the as-made solids but their 29Si NMR spectra are significantly different, revealing the sensitivity of the method to the environment of silicon atoms in the framework. The extent of fluoride that can be removed from D4R units depends not only on the framework Ge content but also on the zeolite topology: for similar contents, F is much more easily eliminated from ITQ-17 than from ITQ-13. © 2011 American Chemical Society.

Data Elevator

Energy Technology Data Exchange (ETDEWEB)

2017-04-29

Data Elevator: Efficient Asynchronous Data Movement in Hierarchical Storage Systems Multi-layer storage subsystems, including SSD-based burst buffers and disk-based parallel file systems (PFS), are becoming part of HPC systems. However, software for this storage hierarchy is still in its infancy. Applications may have to explicitly move data among the storage layers. We propose Data Elevator for transparently and efficiently moving data between a burst buffer and a PFS. Users specify the final destination for their data, typically on PFS, Data Elevator intercepts the I/O calls, stages data on burst buffer, and then asynchronously transfers the data to their final destination in the background. This system allows extensive optimizations, such as overlapping read and write operations, choosing I/O modes, and aligning buffer boundaries. In tests with large-scale scientific applications, Data Elevator is as much as 4.2X faster than Cray DataWarp, the start-of-art software for burst buffer, and 4X faster than directly writing to PFS. The Data Elevator library uses HDF5's Virtual Object Layer (VOL) for intercepting parallel I/O calls that write data to PFS. The intercepted calls are redirected to the Data Elevator, which provides a handle to write the file in a faster and intermediate burst buffer system. Once the application finishes writing the data to the burst buffer, the Data Elevator job uses HDF5 to move the data to final destination in an asynchronous manner. Hence, using the Data Elevator library is currently useful for applications that call HDF5 for writing data files. Also, the Data Elevator depends on the HDF5 VOL functionality.

Climate change impacts on high-elevation hydroelectricity in California

Science.gov (United States)

Madani, Kaveh; Guégan, Marion; Uvo, Cintia B.

2014-03-01

While only about 30% of California's usable water storage capacity lies at higher elevations, high-elevation (above 300 m) hydropower units generate, on average, 74% of California's in-state hydroelectricity. In general, high-elevation plants have small man-made reservoirs and rely mainly on snowpack. Their low built-in storage capacity is a concern with regard to climate warming. Snowmelt is expected to shift to earlier in the year, and the system may not be able to store sufficient water for release in high-demand periods. Previous studies have explored the climate warming effects on California's high-elevation hydropower by focusing on the supply side (exploring the effects of hydrological changes on generation and revenues) ignoring the warming effects on hydroelectricity demand and pricing. This study extends the previous work by simultaneous consideration of climate change effects on high-elevation hydropower supply and pricing in California. The California's Energy-Based Hydropower Optimization Model (EBHOM 2.0) is applied to evaluate the adaptability of California's high-elevation hydropower system to climate warming, considering the warming effects on hydroelectricity supply and pricing. The model's results relative to energy generation, energy spills, reservoir energy storage, and average shadow prices of energy generation and storage capacity expansion are examined and discussed. These results are compared with previous studies to emphasize the need to consider climate change effects on hydroelectricity demand and pricing when exploring the effects of climate change on hydropower operations.

Elevated Cancer-Specific Mortality Among HIV-Infected Patients in the United States.

Science.gov (United States)

Coghill, Anna E; Shiels, Meredith S; Suneja, Gita; Engels, Eric A

2015-07-20

Despite advances in the treatment of HIV, HIV-infected people remain at increased risk for many cancers, and the number of non-AIDS-defining cancers is increasing with the aging of the HIV-infected population. No prior study has comprehensively evaluated the effect of HIV on cancer-specific mortality. We identified cases of 14 common cancers occurring from 1996 to 2010 in six US states participating in a linkage of cancer and HIV/AIDS registries. We used Cox regression to examine the association between patient HIV status and death resulting from the presenting cancer (ascertained from death certificates), adjusting for age, sex, race/ethnicity, year of cancer diagnosis, and cancer stage. We included 1,816,461 patients with cancer, 6,459 (0.36%) of whom were HIV infected. Cancer-specific mortality was significantly elevated in HIV-infected compared with HIV-uninfected patients for many cancers: colorectum (adjusted hazard ratio [HR], 1.49; 95% CI, 1.21 to 1.84), pancreas (HR, 1.71; 95% CI, 1.35 to 2.18), larynx (HR, 1.62; 95% CI, 1.06 to 2.47), lung (HR, 1.28; 95% CI, 1.17 to 1.39), melanoma (HR, 1.72; 95% CI, 1.09 to 2.70), breast (HR, 2.61; 95% CI, 2.06 to 3.31), and prostate (HR, 1.57; 95% CI, 1.02 to 2.41). HIV was not associated with increased cancer-specific mortality for anal cancer, Hodgkin lymphoma, or diffuse large B-cell lymphoma. After further adjustment for cancer treatment, HIV remained associated with elevated cancer-specific mortality for common non-AIDS-defining cancers: colorectum (HR, 1.40; 95% CI, 1.09 to 1.80), lung (HR, 1.28; 95% CI, 1.14 to 1.44), melanoma (HR, 1.93; 95% CI, 1.14 to 3.27), and breast (HR, 2.64; 95% CI, 1.86 to 3.73). HIV-infected patients with cancer experienced higher cancer-specific mortality than HIV-uninfected patients, independent of cancer stage or receipt of cancer treatment. The elevation in cancer-specific mortality among HIV-infected patients may be attributable to unmeasured stage or treatment differences as well

Foreign research reactor irradiated nuclear fuel inventories containing HEU and LEU of United States origin

International Nuclear Information System (INIS)

Matos, J.E.

1994-12-01

This report provides estimates of foreign research reactor inventories of aluminum-based and TRIGA irradiated nuclear fuel elements containing highly enriched and low enriched uranium of United States origin that are anticipated in January 1996, January 2001, and January 2006. These fuels from 104 research reactors in 41 countries are the same aluminum-based and TRIGA fuels that were eligible for receipt under the Department of Energy's Offsite Fuels Policy that was in effect in 1988. All fuel inventory and reactor data that were available as of December 1, 1994, have been included in the estimates of approximately 14,300 irradiated fuel elements in January 1996, 18,800 in January 2001, and 22,700 in January 2006

A double-leg donor-acceptor molecular elevator: new insight into controlling the distance of two platforms.

Science.gov (United States)

Zhang, Zhi-Jun; Han, Min; Zhang, Heng-Yi; Liu, Yu

2013-04-05

A double-leg elevator with an electron-rich anthracene moiety at the platformlike component and an electron-deficient naphthalenediimide unit in the middle of a double-leg riglike component was prepared through "click chemistry", in which the reversible elevator movement between different levels could be controlled upon the addition of base and acid.

Containment long-term operational integrity

International Nuclear Information System (INIS)

Sammataro, R.F.

1990-01-01

Periodic integrated leak rate tests are required to assure that containments continue to meet allowable leakage limits. Although overall performance has been quite good to date, several major containment aging and degradation mechanisms have been identified. Two pilot plant life extension (PLEX) studies serve as models for extending the operational integrity of present containments for light-water cooled nuclear power plants in the United States. One study is for a Boiling-Water Reactor (BWR) and the second is for a Pressurized-Water Reactor (PWR). Research and testing programs for determining the ultimate pressure capacity and failure mechanisms for containments under severe loading conditions and studies for extending the life of current plants beyond the present 40-year licensed lifetime are under way. This paper presents an overview of containment designs in the United States. Also presented are a discussion of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code (ASME Code) and regulatory authority requirements for the design, construction, inservice inspection, leakage testing and repair of steel and concrete containments. Findings for containments from the pilot PLEX studies and continuing containment integrity research and testing programs are discussed. The ASME Code and regulatory requirements together with recommendations from the PLEX studies and containment integrity research and testing provide a basis for continued containment long-term operational integrity. (orig./GL)

Alternative containers for low-level wastes containing large amounts of tritium

International Nuclear Information System (INIS)

Gause, E.P.; Lee, B.S.; MacKenzie, D.R.; Wiswall, R. Jr.

1984-11-01

High-activity tritiated waste generated in the United States is mainly composed of tritium gas and tritium-contaminated organic solvents sorbed onto Speedi-Dri which are packaged in small glass bulbs. Low-activity waste consists of solidified and adsorbed liquids. In this report, current packages for high-activity gaseous and low-activity adsorbed liquid wastes are emphasized with regard to containment potential. Containers for low-level radioactive waste containing large amounts of tritium need to be developed. An integrity may be threatened by: physical degradation due to soil corrosion, gas pressure build-up (due to radiolysis and/or biodegradation), rapid permeation of tritium through the container, and corrosion from container contents. Literature available on these points is summarized in this report. 136 references, 20 figures, 40 tables

Container inspection in the port container terminal by using 14 MeV neutrons

Energy Technology Data Exchange (ETDEWEB)

Valkovic, Vladivoj [Institute Ruder Boskovic, Zagreb (Croatia); Kvinticka 62, Zagreb (Croatia); Sudac, Davorin; Nad, Karlo; Obhodas, Jasmina [Ruder Boskovic Institute, Bijenicka c.54, Zagreb (Croatia)

2015-07-01

A proposal for an autonomous and flexible ship container inspection system is presented. This could be accomplished by the incorporation of inspection system on the container transportation devices (straddle carriers, yard gentry cranes automated guided vehicles, trailers). This configuration is terminal specific and it will be decided by container terminal operator. In such a way no part of port operational area will be used for inspection. The inspection scenario will include container transfer from ship to transportation device with inspection unit mounted on it, inspection during container movement to the container location. A neutron generator without associated alpha particle detection will be used. This will allow the use of higher neutron intensity (5x10{sup 9} - 10{sup 10} n/s in 4π). The inspected container will be stationary in the 'inspection position' on the transportation device while the 'inspection unit' will move along its side. Following analytical methods will be used simultaneously: neutron radiography, X-ray radiography, neutron activation analysis, (n,γ) and (n,n'γ) reactions, neutron absorption, and scattering, X-ray backscattering, Neutron techniques will take the advantage of using 'smart collimators' for neutrons and gammas, both emitted and detected. The inspected voxel will be defined by intersections/union of neutron generator and detectors solid angles. The container inspection protocol will be based on identification of discrepancies between its cargo manifest and its elemental 'fingerprint' and radiography profiles. In addition, the information on container weight will be obtained during the container transport and foreseen screening from the measurement of density of material in the container. (authors)

Elevation Difference and Bouguer Anomaly Analysis Tool (EDBAAT) User's Guide

Science.gov (United States)

Smittle, Aaron M.; Shoberg, Thomas G.

2017-06-16

This report describes a software tool that imports gravity anomaly point data from the Gravity Database of the United States (GDUS) of the National Geospatial-Intelligence Agency and University of Texas at El Paso along with elevation data from The National Map (TNM) of the U.S. Geological Survey that lie within a user-specified geographic area of interest. Further, the tool integrates these two sets of data spatially and analyzes the consistency of the elevation of each gravity station from the GDUS with TNM elevation data; it also evaluates the consistency of gravity anomaly data within the GDUS data repository. The tool bins the GDUS data based on user-defined criteria of elevation misfit between the GDUS and TNM elevation data. It also provides users with a list of points from the GDUS data, which have Bouguer anomaly values that are considered outliers (two standard deviations or greater) with respect to other nearby GDUS anomaly data. “Nearby” can be defined by the user at time of execution. These outputs should allow users to quickly and efficiently choose which points from the GDUS would be most useful in reconnaissance studies or in augmenting and extending the range of individual gravity studies.

Evaluation and improvement of air quality in school public elevator.

Science.gov (United States)

Hsu, Ching-Shan; Huang, Da-Ji

2014-05-01

Public elevators are an essential requirement in modern high-rise buildings. However, the confined, crowded interior of an elevator provides an ideal breeding ground for all manners of biological aerosols. Consequently, when using an elevator at a university in Taiwan as the research target, this study performs an experimental investigation into the effectiveness of hand-sprayed gaseous chlorine dioxide as a disinfection agent. The air quality before and after disinfection is evaluated by measuring the bioaerosol concentrations of bacteria and fungi, respectively. The average background levels of bacteria and fungi before disinfection are found to be 635.7 ± 469.6 and 1296.8 ± 966.6 colony-forming unit (CFU)/m(3), respectively. Following disinfection, the bacteria and fungi concentrations reduced by an average of 35 and 25 %, respectively. The multivariate analysis of variance (MANOVA) results showed that the residual bacteria and fungi concentration levels were determined primarily by the number of individuals within the elevator and the elapsed time following disinfection. In general, the present results show that given a maximum of five individuals within the elevator, a disinfection schedule of once every 40 min is sufficient to reduce the bioaerosol concentrations of bacteria and fungi to the levels specified by the Taiwan Environmental Protection Agency (EPA).

Elevated temperature study of Nd-Fe-B--based magnets with cobalt and dysprosium additions

International Nuclear Information System (INIS)

Gauder, D.R.; Froning, M.H.; White, R.J.; Ray, A.E.

1988-01-01

This paper discusses the elevated temperature performance of Nd-Fe-B magnets containing 0--15 wt. % cobalt substitutions for iron and 0--10 wt. % dysprosium substitutions for neodymium. Test samples were prepared using conventional powder metallurgy techniques. Elevated temperature hysteresis loop and open-circuit measurements were performed on the samples to investigate irreversible losses and long term aging losses at 150 0 C. Magnets with high amounts of both cobalt and dysprosium exhibited lower losses of coercivity and magnetization. Dysprosium had more influence on the elevated temperature performance of the material than did cobalt

Increased large VLDL particles confer elevated cholesteryl ester transfer in diabetes

NARCIS (Netherlands)

Dullaart, Robin P. F.; de Vries, Rindert; Kwakernaak, Arjan J.; Perton, Frank; Dallinga-Thie, Geesje M.

BackgroundPlasma cholesteryl ester transfer (CET), reflecting transfer of cholesteryl esters from high density lipoproteins (HDL) towards apolipoprotein B-containing lipoproteins, may promote atherosclerosis development, and is elevated in Type 2 diabetes mellitus (T2DM). We determined the extent to

P Elevator: An Innovatively Designed Elevator for Extraction of Third Molars.

Science.gov (United States)

Singh, Pradeep; Xiao, Shui Sheng; Ajmera, Deepal Haresh

2015-01-01

To modify the conventional straight elevator with a unique and innovative design in respect to approach and accessibility during extraction for patients with abrasions around corners of the mouth and with thick buccal mucosa, without causing overstretching of angles of the mouth. The shank of the straight elevator in the shape of a 'U' was modified, giving it a shape similar to 'P' in the English alphabet hence it is named the P Elevator. The P elevator utilises a 'U' shaped bend in the shank of the conventional straight elevator making space for the buccal soft tissues and the angle of the mouth, to accommodate properly in the 'U' shank. The application of this elevator in the successful removal of third molars is described. Two hundred patients underwent extraction of third molars with the P elevator including 166 patients with disimpaction of all third molars, 23 patients with abrasion around the angle of the mouth, and 11 patients with thick buccal mucosa. Satisfactory results were obtained in all the cases with no postoperative complications. The P elevator permits prudent, meticulous, innovative and proficient extraction of third molars in patients with thick buccal mucosa and abrasions around the angle of the mouth, without overstretching the corners of the mouth. We introduce novel applications of the P elevator in third molar extraction that provide substantial advantages over a conventional straight elevator.

Comparison of Thermodynamic Predictions and Experimental Observations on B Additions in Powder-Processed Ni-Based Superalloys Containing Elevated Concentrations of Nb

Science.gov (United States)

Antonov, Stoichko; Huo, Jiajie; Feng, Qiang; Isheim, Dieter; Seidman, David N.; Sun, Eugene; Tin, Sammy

2018-03-01

Boron additions to Ni-based superalloys are considered to be beneficial to the creep properties of the alloy, as boron has often been reported to increase grain boundary cohesion, increase ductility, and promote the formation of stable boride phases. Despite the importance, it is not well understood whether these improvements are associated with the presence of elemental boron or stable borides along the grain boundaries. In this investigation, two experimental powder-processed Ni-based superalloys containing elevated levels of Nb were found to exhibit increased solubility for B in the γ matrix when compared to similar commercial Ni-based superalloys. This resulted in an overall lower B concentration at grain boundaries that suppressed boride formation. As the predictive capability of CALPHAD database models for Ni-based superalloys have improved over the years, some discrepancies may still persist around compositionally heterogeneous features such as grain boundaries. Improved quantification of the characteristic partitioning of B as a function of the bulk alloy composition is required for understanding and predicting the stability of borides.

Creep of Sylramic-iBN Fiber Tows at Elevated Temperature in Air and in Silicic Acid-Saturated Steam

Science.gov (United States)

2015-06-01

CREEP OF SYLRAMIC-iBN FIBER TOWS AT ELEVATED TEMPERATURE IN AIR AND IN SILICIC ACID-SATURATED STEAM ...protection in the United States. AFIT-ENY-15-J-46 CREEP OF SYLRAMIC-iBN FIBER TOWS AT ELEVATED TEMPERATURE IN AIR AND IN SILICIC ACID-SATURATED STEAM ...DISTRIBUTION UNLIMITED. AFIT-ENY-15-J-46 CREEP OF SYLRAMIC-iBN FIBER TOWS AT ELEVATED TEMPERATURE IN AIR AND IN SILICIC ACID-SATURATED STEAM

Inventory of power plants in the United States 1989. [Contains glossary

Energy Technology Data Exchange (ETDEWEB)

1990-09-21

This document is prepared annually by the Electric Power Division, Office of Coal, Nuclear, Electric and Alternate Fuels, Energy Information Administration (EIA), US Department of Energy (DOE). The purpose of this publication is to provide year-end statistics about electric generating units in operation and to provide a 10-year outlook of future generating unit additions by electric utilities in the United States (the 50 states and the District of Columbia). Data summarized in this report are useful to a wide audience including Congress, federal and state agencies, the electric utility industry, and the general public. The data presented in this report were assembled and published by the EIA, to fulfill its data collection and dissemination responsibilities as specified in the Federal Energy Administration Act of 1974 (Public Law 93-275) as amended. The report is organized into the following chapters: Summary Statistics; Operable Electric Generating Units; and Projected Electric Generating Unit Additions.

IM-16: A new microporous germanosilicate with a novel framework topology containing d4r and mtw composite building units

International Nuclear Information System (INIS)

Lorgouilloux, Yannick; Dodin, Mathias; Paillaud, Jean-Louis; Caullet, Philippe; Michelin, Laure; Josien, Ludovic; Ersen, Ovidiu; Bats, Nicolas

2009-01-01

The synthesis and the structure of IM-16 a new germanosilicate with a novel zeolitic topology prepared hydrothermally with the ionic liquid 3-ethyl-1-methyl-3H-imidazol-1-ium as the organic structure-directing agent are reported. The structure of calcined and partially rehydrated IM-16 of chemical formula |(H 2 O) 0.16 |[Si 3.47 Ge 2.53 O 12 ] was solved from powder XRD data in space group Cmcm with a=15.0861(2) A, b=17.7719(3) A, c=19.9764(3) A, V=5355.84(12) A 3 (Z=16). This new zeolite framework type contains 10-MRs channels and may be described from the d4r and mtw composite building units. - Graphical abstract: The synthesis and the structure of IM-16 a new germanosilicate with a novel zeolitic topology prepared hydrothermally with the ionic liquid 3-ethyl-1-methyl-3H-imidazol-1-ium as the organic structure-directing agent are reported. This new zeolite framework type contains 10-MRs channels and may be described from the d4r and mtw composite building units

Development of filtered containment venting system and application for Kashiwazaki-Kariwa Nuclear Power Station Unit 6, 7

International Nuclear Information System (INIS)

Murai, Soutarou; Hiranuma, Naoki; Kimura, Takeo; Omori, Shuichi; Watanabe, Fumitoshi; Sasa, Daisuke

2014-01-01

The Fukushima Dai-ichi Nuclear Power Station (1F) of Tokyo Electric Power Company (TEPCO) had experienced severe radio-active release to the environment in the Tohoku Region Pacific Coast Earthquake (alias: the Great East Japan Earthquake) in 2011. Under the Station Black-Out (SBO) conditions caused by tsunami with the earthquake, the 1F operators had tried to vent the gasses in the Primary Containment Vessels (PCVs) of the unit 1, 2 and 3 to the environment through the water pools in the suppression chambers of the PCVs. Its venting, however, was imperfect and, as a result, major direct radio-active release to the environment was caused. After this disaster, TEPCO launched a project to develop the Filtered Containment Venting System (FCVS), in which our very bitter experiences in the 1F accident as described above are reflected. One of the main purposes of the development of the FCVS is to enhance operability of venting under the severe plant conditions such as the SBO during progressing of severe core damage, and another is to enhance removal performance of radio-nuclides with the newly added filtering equipment, which is installed in the venting line from the PCV to the outer. The Kashiwazaki-Kariwa NPS unit 6 and 7 will be the first reactors applied the FCVSs. In this paper, we show the design concept of the TEPCO's FCVS, the brief overview of the system design and the summary of experiment which has been performed for getting the performance data of the FCVS such as decontamination factor in various conditions. (author)

The 3D Elevation Program: summary for Puerto Rico

Science.gov (United States)

Carswell, William J.

2016-02-03

Elevation data are essential to a broad range of applications, including forest resources management, wildlife and habitat management, scientific research, national security, recreation, and many others. For the Commonwealth of Puerto Rico, elevation data are critical for flood risk management, landslide mitigation, natural resources conservation, sea level rise and subsidence, coastal zone management, infrastructure and construction management, and other business uses. Today, high-density light detection and ranging (lidar) data are the primary sources for deriving elevation models and other datasets. Federal, State, Tribal, U.S. territorial, and local agencies work in partnership to (1) replace data that are older and of lower quality and (2) provide coverage where publicly accessible data do not exist. A joint goal of State and Federal partners is to acquire consistent, statewide coverage to support existing and emerging applications enabled by lidar data.The National Enhanced Elevation Assessment evaluated multiple elevation data acquisition options to determine the optimal data quality and data replacement cycle relative to cost to meet the identified requirements of the user community. The evaluation demonstrated that lidar acquisition at quality level 2 for the conterminous United States, Hawaii, and selected U.S. territories, and quality level 5 interferometric synthetic aperture radar (IfSAR) data for Alaska, all with a 6- to 10-year acquisition cycle, provided the highest benefit/cost ratios. The 3D Elevation Program (3DEP) initiative selected an 8-year acquisition cycle for the respective quality levels. 3DEP, managed by the U.S. Geological Survey (USGS), the Office of Management and Budget Circular A‒16 lead agency for terrestrial elevation data, responds to the growing need for high-quality topographic data and a wide range of other three-dimensional (3D) representations of the Nation’s natural and constructed features.

High-speed elevators controlled by inverters

Energy Technology Data Exchange (ETDEWEB)

Sakai, Yoshio; Takahashi, Hideaki; Nakamura, Kiyoshi; Kinoshita, Hiroshi

1988-10-25

The super-high-speed elevator with superiority to 300m/min of speed, requires both the large capacity power and wide range speed controls. Therefore, in order to materialize the smooth and quiet operation characteristics, by applying the inverter control, the low torque ripple control in the low frequency range and high frequency large capacity inverting for lowering the motor in noise are necessary with their being assured of reliability. To satisfy the above necessary items, together with the development of a sine wave pulse width and frequency modulation (PWM/PFM) control system, to more precisely enable the sine wave electric current control, and 3kHz switching power converter, using a 800A power transistor module, a supervoltage control circuit under the extraordinary condition was designed. As a result of commercializing a 360m/min super-high speed inverter elevator, the power source unit, due to the effect of high power factor, could be reduced by 30% in capacity and also the higher harmonic wave including ratio could be considerably lowered to the inferiority to 5%. 2 references, 7 figures, 1 table.

Probabilistic analysis of Millstone Unit 3 ultimate containment failure probability given high pressure: Chapter 14

International Nuclear Information System (INIS)

Bickel, J.H.

1983-01-01

The quantification of the containment event trees in the Millstone Unit 3 Probabilistic Safety Study utilizes a conditional probability of failure given high pressure which is based on a new approach. The generation of this conditional probability was based on a weakest link failure mode model which considered contributions from a number of overlapping failure modes. This overlap effect was due to a number of failure modes whose mean failure pressures were clustered within a 5 psi range and which had uncertainties due to variances in material strengths and analytical uncertainties which were between 9 and 15 psi. Based on a review of possible probability laws to describe the failure probability of individual structural failure modes, it was determined that a Weibull probability law most adequately described the randomness in the physical process of interest. The resultant conditional probability of failure is found to have a median failure pressure of 132.4 psia. The corresponding 5-95 percentile values are 112 psia and 146.7 psia respectively. The skewed nature of the conditional probability of failure vs. pressure results in a lower overall containment failure probability for an appreciable number of the severe accident sequences of interest, but also probabilities which are more rigorously traceable from first principles

Containment event analysis for postulated severe accidents: Peach Bottom Atomic Power Station, Unit 2. Draft report for comment

Energy Technology Data Exchange (ETDEWEB)

Amos, C N [Technadyne Engineering Consultants, Inc., Albuquerque, NM (United States); Griesmeyer, J M [Sandia National Laboratories, Albuquerque, NM (United States); Kolaczkowski, A M [Science Applications International Corporation, Albuquerque, NM (United States)

1987-05-01

A study has been performed as part of the Severe Accident Risk Reduction Program (SARRP) to investigate the response of a particular boiling water reactor with a Mark I containment (Peach Bottom Unit 2) to postulated severe accidents. A detailed containment event tree for the Peach Bottom plant has been developed to describe the various possible accident pathways that can lead to radioactive releases from containment. Data and analyses from a large number of NRC and industry-sponsored programs have been reviewed and used as a basis for quantifying the event tree, i.e., determining the likelihood of the pathways at each branch point for a variety of accident sequence initiators. A generalized containment event tree code, called EVNTRE, has been developed to facilitate the quantification. The uncertainty in the results has been examined by performing the quantification three times, using a different set of input each time to represent the variation of opinion in the reactor safety community. In the so-called 'central' estimate, the likelihood of early containment failure (occurring before or within a short time after reactor vessel breach) was found to be significant because of the possible occurrence of the following phenomena that can threaten containment integrity: (1) meltthrough of the drywell shell caused by thermal attack from core debris, and (2) drywell overpressurization caused by rapid depressurization of the reactor vessel in combination with other events such as direct heating. However, uncertainties surrounding these issues could cause the early failure likelihood to be significantly lower than in the central estimate. This work supports NRC's assessment of severe accident risks to be published in NUREG-1150. (author)

Elevated Liver Enzymes

Science.gov (United States)

Symptoms Elevated liver enzymes By Mayo Clinic Staff Elevated liver enzymes may indicate inflammation or damage to cells in the liver. Inflamed or ... than normal amounts of certain chemicals, including liver enzymes, into the bloodstream, which can result in elevated ...

Containment closure time following loss of cooling under shutdown conditions of YGN units 3 and 4

International Nuclear Information System (INIS)

Seul, Kwang Won; Bang, Young Seok; Kim, Se Won; Kim, Hho Jung

1998-01-01

The YGN Units 3 and 4 plant conditions during shutdown operation were reviewed to identify the possible event scenarios following the loss of shutdown cooling. The thermal hydraulic analyses were performed for the five cases of RCS configurations under the worst event scenario, unavailable secondary cooling and no RCS inventory makeup, using the RELAP5/MOD3.2 code to investigate the plant behavior. From the analyses results, times to boil, times to core uncovery and times to core heat up were estimated to determine the containment closure time to prevent the uncontrolled release of fission products to atmosphere. These data provide useful information to the abnormal procedure to cope with the event

Microfracture behaviour of extruded Mg–Zn–Y alloys containing long-period stacking ordered structure at room and elevated temperatures

International Nuclear Information System (INIS)

Mine, Yoji; Yoshimura, Hajime; Matsuda, Mitsuhiro; Takashima, Kazuki; Kawamura, Yoshihito

2013-01-01

We studied the fracture behaviour of extruded Mg–Zn–Y alloys at room temperature (RT) and at 523 K using microfracture testing. An Mg 97 Zn 1 Y 2 alloy was used to obtain two-phase specimens consisting of α-Mg and long-period stacking ordered (LPSO) structure phases, and an Mg 88 Zn 5 Y 7 alloy was used to obtain specimens consisting of an LPSO phase. The microfracture testing of the two-phase specimen revealed that the fracture behaviour changed from brittle to ductile as the testing temperature increased. By contrast, the LPSO-phase specimen remained brittle even at the elevated temperature and the intrinsic fracture toughness values obtained at both testing temperatures were nearly identical. Ex situ transmission electron microscopy of the two-phase specimen showed that mechanical twinning in the α-Mg phase did not occur at the elevated temperature, although it was activated at RT. This suggests that the plastic deformation mode in the α-Mg phase plays a crucial part in the enhanced crack growth resistance of the two-phase alloy at the elevated temperature

Application of containment codes to LMFBRs in the United States

International Nuclear Information System (INIS)

Chang, Y.W.

1977-01-01

This paper describes the application of containment codes to predict the response of the fast reactor containment and the primary piping loops to HCDAs. Five sample problems are given to illustrate their applications. The first problem deals with the response of the primary containment to an HCDA. The second problem deals with the coolant flow in the reactor lower plenum. The third problem concerns sodium spillage and slug impact. The fourth problem deals with the response of a piping loop. The fifth problem analyzes the response of a reactor head closure. Application of codes in parametric studies and comparison of code predictions with experiments are also discussed. (Auth.)

Application of containment codes to LMFBRs in the United States

International Nuclear Information System (INIS)

Chang, Y.W.

1977-01-01

The application of containment codes to predict the response of the fast reactor containment and the primary piping loops to HCDAs is described. Five sample problems are given to illustrate their applications. The first problem deals with the response of the primary containment to an HCDA. The second problem deals with the coolant flow in the reactor lower plenum. The third proem concerns sodium spillage and slug impact. The fourth problem deals with the response of a piping loop. The fifth problem analyzes the response of a reactor head closure. Application of codes in parametric studies and comparison of code predictions with experiments are also discussed

Variations in dark respiration and mitochondrial numbers within needles of Pinus radiata grown in ambient or elevated CO2 partial pressure

International Nuclear Information System (INIS)

Griffin, K. L.; Anderson, O. R.; Tissue, D. T.; Turnbull, M. H.; Whitehead, D.

2004-01-01

An experiment involving comparison of within-leaf variations in cell size, mitochondrial numbers and dark respiration in the most recently expanded tip, the mid-section and the base of needles of Pinus radiata grown for four years at ambient and elevated carbon dioxide partial pressure, is described. Results showed variation in mitochondrial numbers and respiration along the length of the needle, with the highest number of mitochondria per unit cytoplasm and the highest rate of respiration per unit leaf area at the base of the needle. Elevated carbon dioxide pressure caused the number of mitochondria per unit cytoplasm to double regardless of location (tip, basal or mid sections). Under these conditions, greatest mitochondrial density was observed at the tip. The mean size of mitochondria was not affected by either growth at elevated carbon dioxide pressure or by position on the needle. Respiration per unit leaf area at elevated carbon dioxide pressure was highest at the tip of needles, decreasing towards the middle and basal sections. The observed data supports the hypothesis that the highest number of mitochondria per unit area of cytoplasm occurs at the base of the needle, but does not support the hypothesis that the lowest rate of respiration also occurs at the base. It is suggested that the relationship that determines the association between structure and function in these needles is more complex than previously thought. 33 refs., 4 tabs., 1 fig

Creating a Coastal National Elevation Database (CoNED) for science and conservation applications

Science.gov (United States)

Thatcher, Cindy A.; Brock, John C.; Danielson, Jeffrey J.; Poppenga, Sandra K.; Gesch, Dean B.; Palaseanu-Lovejoy, Monica; Barras, John; Evans, Gayla A.; Gibbs, Ann

2016-01-01

The U.S. Geological Survey is creating the Coastal National Elevation Database, an expanding set of topobathymetric elevation models that extend seamlessly across coastal regions of high societal or ecological significance in the United States that are undergoing rapid change or are threatened by inundation hazards. Topobathymetric elevation models are raster datasets useful for inundation prediction and other earth science applications, such as the development of sediment-transport and storm surge models. These topobathymetric elevation models are being constructed by the broad regional assimilation of numerous topographic and bathymetric datasets, and are intended to fulfill the pressing needs of decision makers establishing policies for hazard mitigation and emergency preparedness, coastal managers tasked with coastal planning compatible with predictions of inundation due to sea-level rise, and scientists investigating processes of coastal geomorphic change. A key priority of this coastal elevation mapping effort is to foster collaborative lidar acquisitions that meet the standards of the USGS National Geospatial Program's 3D Elevation Program, a nationwide initiative to systematically collect high-quality elevation data. The focus regions are located in highly dynamic environments, for example in areas subject to shoreline change, rapid wetland loss, hurricane impacts such as overwash and wave scouring, and/or human-induced changes to coastal topography.

Register of basic residential units and spatial units in the Slovak Republic

International Nuclear Information System (INIS)

Galdik, S.; Vavrinec, B.

2005-01-01

In this contribution authors deal with the register of basic residential units and spatial units in the Slovak Republic. Classification of statistical territorial units is presented. Map data and statistical data contain information about environmental impact of industrial and energetic mills

Anomalous elevated radiocarbon measurements of PM{sub 2.5}

Energy Technology Data Exchange (ETDEWEB)

Buchholz, Bruce A., E-mail: buchholz2@llnl.gov [Center for Accelerator Mass Spectrometry, Mail Stop L-397, Lawrence Livermore National Laboratory, P.O. Box 808 Livermore, CA 94551 (United States); Fallon, Stewart J. [Center for Accelerator Mass Spectrometry, Mail Stop L-397, Lawrence Livermore National Laboratory, P.O. Box 808 Livermore, CA 94551 (United States); Radiocarbon Dating Laboratory, Research School of Earth Sciences, Australian National University, Canberra, ACT 0200 (Australia); Zermeno, Paula; Bench, Graham [Center for Accelerator Mass Spectrometry, Mail Stop L-397, Lawrence Livermore National Laboratory, P.O. Box 808 Livermore, CA 94551 (United States); Schichtel, Bret A. [Cooperative Institute for Research in the Atmosphere, Colorado State University, 1375 Campus Delivery, Fort Collins, CO 80523 (United States)

2013-01-15

Two-component models are often used to determine the contributions made by fossil fuel and natural sources of carbon in airborne particulate matter (PM). The models reduce thousands of actual sources to two end members based on isotopic signature. Combustion of fossil fuels produces PM free of carbon-14 ({sup 14}C). Wood or charcoal smoke, restaurant fryer emissions, and natural emissions from plants produce PM with the contemporary concentration of {sup 14}C approximately 1.2 Multiplication-Sign 10{sup -1214}C/C. Such data can be used to estimate the relative contributions of fossil fuels and biogenic aerosols to the total aerosol loading and radiocarbon analysis is becoming a popular source apportionment method. Emissions from incinerators combusting medical or biological wastes containing tracer {sup 14}C can skew the {sup 14}C/C ratio of PM, however, so critical analysis of sampling sites for possible sources of elevated PM needs to be completed prior to embarking on sampling campaigns. Results are presented for two ambient monitoring sites in different areas of the United States where {sup 14}C contamination is apparent. Our experience suggests that such contamination is uncommon but is also not rare ({approx}10%) for PM sampling sites.

Influence of Common Bean (Phaseolus vulgaris) Grown in Elevated CO2 on Apatite Dissolution

Science.gov (United States)

Olsen, A. A.; Morra, B.

2016-12-01

We ran a series of experiments to test the hypothesis that release of plant nutrients contained in apatite will be accelerated by the growth of Langstrath Stringless green bean in the presence of atmospheric CO2 meant to simulate possible future atmospheric conditions due a higher demand of nutrients and growth rate caused by elevated CO2. We hypothesize that elevated atmospheric CO2 will lead to both increased root growth and organic acid exudation. These two traits will lead to improved acquisition of P derived from apatite. Experiments were designed to investigate the effect of these changes on soil mineral weathering using plants grown under two conditions, ambient CO2 (400ppm) and elevated CO2 (1000ppm). Plants were grown in flow-through microcosms consisting of a mixture of quartz and apatite sands. Mini-greenhouses were utilized to control CO2 levels. Plant growth was sustained by a nutrient solution lacking in Ca and P. Calcium and P content of the leachate and plant tissue served as a proxy for apatite dissolution. Plants were harvested biweekly during the eight-week experiment and analyzed for Ca and P to calculate apatite dissolution kinetics. Preliminary results suggest that approximately four times more P and Ca are present in the leachate from experiments containing plants under both ambient and elevated CO2 levels than in abiotic experiments; however, the amounts of both P and Ca released in experiments conducted under both ambient and elevated CO2 levels are similar. Additionally, the amount of P in plant tissue grown under ambient and elevated CO2 conditions is similar. Plants grown in elevated CO2 had a greater root to shoot ratio. The planted microcosms were found to have a lower pH than abiotic controls most likely due to root respiration and exudation of organic acids.

Elevated Plasma Level of Leukotrienes in Bronchial Asthma Patients: A Possible Clinical Relevance

Directory of Open Access Journals (Sweden)

Mahmoud Mansour

1994-01-01

Full Text Available Plasma from bronchial asthma patients and healthy controls was investigated for the content of lipoxygenase products. After lipid extraction using SEP-PAK C18 Cartridges, the lipoxygenase products were measured by Enzyme-Immunoassay. Elevated chemotactic B4 was found in plasma from asthmatic patients with mean value (483±75 pmoUL, while the mean value in normal healthy donors was (140± 12.1 pmol/L (M±SE. The levels of spasmogenic cysteinyl containing leukotrienes were also very high in the bronchial asthma patients. Elevations of leukotriene B4 and cysteinyl containing leukotrienes were detected during attacks of bronchial asthma. These results suggest that leukotriene B4 may be important in the pathogenesis of bronchial asthma and confirmed that peptidoleukotrienes playa role as chemical mediators during the asthmatic attack.

Scattering calculation and image reconstruction using elevation-focused beams.

Science.gov (United States)

Duncan, David P; Astheimer, Jeffrey P; Waag, Robert C

2009-05-01

Pressure scattered by cylindrical and spherical objects with elevation-focused illumination and reception has been analytically calculated, and corresponding cross sections have been reconstructed with a two-dimensional algorithm. Elevation focusing was used to elucidate constraints on quantitative imaging of three-dimensional objects with two-dimensional algorithms. Focused illumination and reception are represented by angular spectra of plane waves that were efficiently computed using a Fourier interpolation method to maintain the same angles for all temporal frequencies. Reconstructions were formed using an eigenfunction method with multiple frequencies, phase compensation, and iteration. The results show that the scattered pressure reduces to a two-dimensional expression, and two-dimensional algorithms are applicable when the region of a three-dimensional object within an elevation-focused beam is approximately constant in elevation. The results also show that energy scattered out of the reception aperture by objects contained within the focused beam can result in the reconstructed values of attenuation slope being greater than true values at the boundary of the object. Reconstructed sound speed images, however, appear to be relatively unaffected by the loss in scattered energy. The broad conclusion that can be drawn from these results is that two-dimensional reconstructions require compensation to account for uncaptured three-dimensional scattering.

Science Unit Plans. PACE '94.

Science.gov (United States)

Schoon, Kenneth J., Ed.; Wiles, Clyde A., Ed.

This booklet contains mathematics unit plans for Biology, Chemistry, and Physical Science developed by PACE (Promoting Academic Excellence In Mathematics, Science & Technology for Workers of the 21st Century). Each unit plan contains suggested timing, objectives, skills to be acquired, workplace relationships, learning activities with suggested…

Experimental prototype of an electric elevator

Science.gov (United States)

Gaiceanu, M.; Epure, S.; Ciuta, S.

2016-08-01

The main objective is to achieve an elevator prototype powered by a three-phase voltage system via a bidirectional static power converter ac-ac with regenerating capability. In order to diminish the power size of the electric motor up to 1/3 of rated power, the elevator contains two carriages of the same weight, one serving as the payload, and the other as counterweight. Before proper operation of the static power converter, the capacitor must be charged at rated voltage via a precharge circuit. At the moment of stabilizing the DC voltage at nominal value, the AC-AC power converter can operates in the proper limits. The functions of the control structure are: the load control task, speed and torque controls. System includes transducers for current measuring, voltage sensors and encoder. As reserve power sources the hybrid battery-photovoltaic panels are used. The control voltage is modulated by implementing four types of pulse width modulations: sinusoidal, with reduced commutation, third order harmonic insertion, and the space vector modulation. Therefore, the prototype could operates with an increased efficiency, in spite of the existing ones. The experimental results confirm the well design of the chosen solution. The control solution assures bidirectional power flow control, precharge control, and load control and it is implemented on a digital signal processor. The elevator capacity is between 300-450 kg, and it is driven by using a 1.5 kW three-phase asynchronous machine.

Containment closure time following loss of cooling under shutdown conditions of YGN units 3 and 4

Energy Technology Data Exchange (ETDEWEB)

Seul, Kwang Won; Bang, Young Seok; Kim, Se Won; Kim, Hho Jung [Korea Institute of Nuclear Safety, Taejon (Korea, Republic of)

1998-12-31

The YGN Units 3 and 4 plant conditions during shutdown operation were reviewed to identify the possible event scenarios following the loss of shutdown cooling. The thermal hydraulic analyses were performed for the five cases of RCS configurations under the worst event scenario, unavailable secondary cooling and no RCS inventory makeup, using the RELAP5/MOD3.2 code to investigate the plant behavior. From the analyses results, times to boil, times to core uncovery and times to core heat up were estimated to determine the containment closure time to prevent the uncontrolled release of fission products to atmosphere. These data provide useful information to the abnormal procedure to cope with the event. 6 refs., 7 figs., 2 tabs. (Author)

Response of Respiration of Soybean Leaves Grown at Ambient and Elevated Carbon Dioxide Concentrations to Day-to-day Variation in Light and Temperature under Field Conditions

Science.gov (United States)

BUNCE, JAMES A.

2005-01-01

• Background and Aims Respiration is an important component of plant carbon balance, but it remains uncertain how respiration will respond to increases in atmospheric carbon dioxide concentration, and there are few measurements of respiration for crop plants grown at elevated [CO2] under field conditions. The hypothesis that respiration of leaves of soybeans grown at elevated [CO2] is increased is tested; and the effects of photosynthesis and acclimation to temperature examined. • Methods Net rates of carbon dioxide exchange were recorded every 10 min, 24 h per day for mature upper canopy leaves of soybeans grown in field plots at the current ambient [CO2] and at ambient plus 350 µmol mol−1 [CO2] in open top chambers. Measurements were made on pairs of leaves from both [CO2] treatments on a total of 16 d during the middle of the growing seasons of two years. • Key Results Elevated [CO2] increased daytime net carbon dioxide fixation rates per unit of leaf area by an average of 48 %, but had no effect on night-time respiration expressed per unit of area, which averaged 53 mmol m−2 d−1 (1·4 µmol m−2 s−1) for both the ambient and elevated [CO2] treatments. Leaf dry mass per unit of area was increased on average by 23 % by elevated [CO2], and respiration per unit of mass was significantly lower at elevated [CO2]. Respiration increased by a factor of 2·5 between 18 and 26 °C average night temperature, for both [CO2] treatments. • Conclusions These results do not support predictions that elevated [CO2] would increase respiration per unit of area by increasing photosynthesis or by increasing leaf mass per unit of area, nor the idea that acclimation of respiration to temperature would be rapid enough to make dark respiration insensitive to variation in temperature between nights. PMID:15781437

De stille elever

DEFF Research Database (Denmark)

Winther-Lindqvist, Ditte Alexandra

2012-01-01

Det er blevet en afgørende samværskompetence i uddannelsessystemet at stå aktivt frem og deltage verbalt i skoleklassens liv både fagligt og socialt. Men ikke alle elever deltager lige villigt verbalt i plenum. Artiklen handler om de stille elever og konsekvenserne af stillehed i skolen. Det...... foreslås at skolesystemet sanktionerer ældre elever hårdere for stillehed end yngre elever og det forklares med at skolelivet også er en kultivering henimod elevhed som social identitet og denne er der forventning om at eleverne mestrer i udskolingen....

Elevated Hemoglobin A1C Levels Correlate with Blood Glucose Elevation in Diabetic Patients following Local Corticosteroid Injection in the Hand: A Prospective Study.

Science.gov (United States)

Kim, Nayoung; Schroeder, Jake; Hoffler, C Edward; Matzon, Jonas L; Lutsky, Kevin F; Beredjiklian, Pedro K

2015-10-01

Diabetic patients develop hand conditions that are managed with local corticosteroid injections. Injections can result in a transient elevation in serum glucose in diabetic patients. Hemoglobin A1c is the accepted measure of long-term plasma glucose control in diabetics (levels ≥7 percent reflect poor blood glucose control). The purpose of this study was to assess the relationship between hemoglobin A1c levels and increased blood glucose levels after corticosteroid injections. Twenty-five diabetic patients were evaluated prospectively. One milliliter containing 10 mg of triamcinolone acetonide was used. The most recent hemoglobin A1c level and normal average blood glucose levels were obtained. Glucose levels were obtained from patient recall of their daily blood glucose self- monitoring on the day of the injection. Postinjection blood glucose levels were recorded until levels returned to preinjection baseline. Twenty patients (80 percent) had elevation of their blood glucose level from baseline. No patient had elevated blood glucose levels after 5 days. Patients with hemoglobin A1c levels greater than or equal to 7 percent had a higher blood glucose elevation and maintained this for longer than those who had a lower hemoglobin A1c level. Patients in the higher hemoglobin A1c group also had a higher number of hyperglycemic events. There was a strong or moderate correlation between hemoglobin A1c and elevated blood glucose levels during days 1 to 4. Patients with hemoglobin A1c levels greater than or equal to 7 percent have elevations in blood glucose that are higher and last longer than patients with lower levels. Hemoglobin A1c levels can be used to roughly predict the degree of blood glucose elevation after corticosteroid injections into the hands of diabetic patients.

Nuclear containment systems and in-service inspection status of Korea nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Jihong, Park; Jaekeun, Hong; Banuk, Park [Korea Institute of Machinery and Materials, Dept. of Authorized Test and Evaluation, Kyungnam (Korea, Republic of)

2007-07-01

20 unit nuclear power plants in Korea have been operated and maintained since the first unit started in commercial service in 1978. Most recently 4 units were under construction and several units were planned to be constructed. by industries. 4 types of nuclear containment systems have been constructed until now: first, metal containments, then pre-stressed concrete containments with grouted tendon systems, followed by pre-stressed concrete containments with un-grouted tendon systems, and Korea standard nuclear containments. All the nuclear containments should be inspected periodically. Therefore for periodic in-service inspection, several appropriate technical requirements should be applied differently depending on the specific nuclear containment types. With the changes of times, nuclear containment systems have undergone a remarkable change, and finally nuclear containment system of Korea standard nuclear power plant was settled down, and as a matter of course it dominates the trend of present and future nuclear containment systems. Overall in-service inspection results of most Korea nuclear containments have not showed any serious evidence of degradation.

Microstructure and elevated-temperature erosion-oxidation behaviour of aluminized 9Cr-1Mo Steel

OpenAIRE

Huttunen, E.; Honkanen, M.; Tsipas, Sophia Alexandra; Omar, H.; Tsipas, D.

2012-01-01

Degradation of materials by a combination of erosive wear and atmospheric oxidation at elevated temperatures constitutes a problem in some power generation processes, such as fluidized-bed combustion. In this work, 9Cr-1Mo steel, a common tube material in combustion chambers, is coated by a pack cementation method from an Al-containing pack in order to improve the resistance to erosion-oxidation at elevated temperatures. The resulting coating is studied in terms of microstructure and microhar...

Mechanical Properties and Fracture Behaviors of the As-Extruded Mg-5Al-3Ca Alloys Containing Yttrium at Elevated Temperature.

Science.gov (United States)

Son, Hyeon-Taek; Kim, Yong-Ho; Kim, Taek-Soo; Lee, Seong-Hee

2016-02-01

Effects of yttrium (Y) addition on mechanical properties and fracture behaviors of the as-extruded Mg-Al-Ca based alloys at elevated temperature were investigated by a tensile test. After hot extrusion, the average grain size was refined by Y addition and eutectic phases were broken down into fine particles. Y addition to Mg-5Al-3Ca based alloy resulted in the improvement of strength and ductility at elevated temperature due to fine grain and suppression of grain growth by formation of thermally stable Al2Y intermetallic compound.

A global digital elevation model - GTOP030

Science.gov (United States)

1999-01-01

GTOP030, the U.S. Geological Survey's (USGS) digital elevation model (DEM) of the Earth, provides the flrst global coverage of moderate resolution elevation data.  The original GTOP30 data set, which was developed over a 3-year period through a collaborative effort led by the USGS, was completed in 1996 at the USGS EROS Data Center in Sioux Falls, South Dakota.  The collaboration involved contributions of staffing, funding, or source data from cooperators including the National Aeronautics and Space Administration (NASA), the United Nations Environment Programme Global Resource Information Database (UNEP/GRID), the U.S. Agency for International Development (USAID), the Instituto Nacional de Estadistica Geografia e Informatica (INEGI) of Mexico, the Geographical Survey Institute (GSI) of Japan, Manaaki Whenua Landcare Research of New Zealand, and the Scientific Committee on Antarctic Research (SCAR). In 1999, work was begun on an update to the GTOP030 data set. Additional data sources are being incorporated into GTOP030 with an enhanced and improved data set planned for release in 2000.

Resource Conservation and Recovery Act closure report: Area 2 Bitcutter and Postshot Containment Shops Injection Wells, Correction Action Unit 90

International Nuclear Information System (INIS)

1996-12-01

This Closure Report provides documentation of the activities conducted during the Resource Conservation and Recovery Act (RCRA) closure of the Bitcutter and Postshot Containment Shops Injection Wells located in Area 2 of the Nevada Test Site (NTS), Oak Spring Quadrangle (USGS, 1986), Township 10 South, Range 53 East, Nye County, Nevada. This report discusses the Bitcutter Shop Inside Injection Well (CAU 90-A) closure-in-place and the Bitcutter Shop Outside Injection Well (CAU 90-B) and Postshot Containment Shop Injection Well (CAU 90-C) clean closures. This Closure Report provides background information about the unit, the results of the characterization activities and actions conducted to determine the closure design. It also provides a discussion of the drainage analysis, preliminary closure activities, final closure activities, waste management activities, and the Post-Closure Care requirements

Cooling device for reactor container

International Nuclear Information System (INIS)

Akiba, Miyuki.

1996-01-01

In a cooling device for a reactor container, a low pressure vessel is connected to an incondensible gas vent tube by way of an opening/closing valve. Upon occurrence of a loss of coolant accident, among steams and incondensible gases contained in the reactor container, steams are cooled and condensed in a heat exchanger. The incondensible gases are at first discharged from the heat exchanger to a suppression pool by way of the incondensible gas vent tube, but subsequently, they are stagnated in the incondensible gas vent tube to hinder heat exchanging and steam cooling and condensing effects in the heat exchanger thereby raising temperature and pressure in the reactor. However, if the opening/closing valve is opened when the incondensible gases are stagnated in the incondensible gas vent tube, since the incondensible gases stagnated in the heat exchanger are sucked and discharged to the low pressure vessel, the performance of the heat exchanger is maintained satisfactorily thereby enabling to suppress elevation of temperature and pressure in the reactor container. (N.H.)

Elevator and hydraulics; Elevator to yuatsu

Energy Technology Data Exchange (ETDEWEB)

Nakamura, I. [Hitachi, Ltd., Tokyo (Japan)

1994-07-15

A hydraulic type elevator is installed in relatively lower buildings as compared with a rope type elevator, but the ratio in the number of installation of the former elevator is increasing. This paper explains from its construction and features to especially various control systems for the riding comfort and safety. A direct push-up system with hydraulic jacks arranged beneath a car, and an indirect push-up system that has hydraulic jacks arranged on flank of a car and transmits the movement of a plunger via a rope are available. The latter system eliminates the need of large holes to embed hydraulic jacks. While the speed is controlled by controlling flow rates of high-pressure oil, the speed, position, acceleration and even time differential calculus of the acceleration must be controlled severely. The system uses two-step control for the through-speed and the landing speed. Different systems that have been realized may include compensation for temperatures in flow rate control valves, load pressures, and oil viscosity, from learning control to fuzzy control for psychological effects, or control of inverters in motors. 13 refs., 12 figs., 1 tab.

Soil nematodes show a mid-elevation diversity maximum and elevational zonation on Mt. Norikura, Japan.

Science.gov (United States)

Dong, Ke; Moroenyane, Itumeleng; Tripathi, Binu; Kerfahi, Dorsaf; Takahashi, Koichi; Yamamoto, Naomichi; An, Choa; Cho, Hyunjun; Adams, Jonathan

2017-06-08

Little is known about how nematode ecology differs across elevational gradients. We investigated the soil nematode community along a ~2,200 m elevational range on Mt. Norikura, Japan, by sequencing the 18S rRNA gene. As with many other groups of organisms, nematode diversity showed a high correlation with elevation, and a maximum in mid-elevations. While elevation itself, in the context of the mid domain effect, could predict the observed unimodal pattern of soil nematode communities along the elevational gradient, mean annual temperature and soil total nitrogen concentration were the best predictors of diversity. We also found nematode community composition showed strong elevational zonation, indicating that a high degree of ecological specialization that may exist in nematodes in relation to elevation-related environmental gradients and certain nematode OTUs had ranges extending across all elevations, and these generalized OTUs made up a greater proportion of the community at high elevations - such that high elevation nematode OTUs had broader elevational ranges on average, providing an example consistent to Rapoport's elevational hypothesis. This study reveals the potential for using sequencing methods to investigate elevational gradients of small soil organisms, providing a method for rapid investigation of patterns without specialized knowledge in taxonomic identification.

Elevators or stairs?

Science.gov (United States)

Shah, Sachin; O’Byrne, Michael; Wilson, Merne; Wilson, Thomas

2011-01-01

Background: Staff in hospitals frequently travel between floors and choose between taking the stairs or elevator. We compared the time savings with these two options. Methods: Four people aged 26–67 years completed 14 trips ranging from one to six floors, both ascending and descending. We compared the amount of time per floor travelled by stairs and by two banks of elevators. Participants reported their fatigue levels using a modified Borg scale. We performed two-way analysis of variance to compare the log-transformed data, with participant and time of day as independent variables. Results: The mean time taken to travel between each floor was 13.1 (standard deviation [SD] 1.7) seconds by stairs and 37.5 (SD 19.0) and 35.6 (SD 23.1) seconds by the two elevators (F = 8.61, p elevator equaled about 15 minutes a day. Self-reported fatigue was less than 13 (out of 20) on the Borg scale for all participants, and they all stated that they were able to continue their duties without resting. The extra time associated with elevator use was because of waiting for its arrival. There was a difference in the amount of time taken to travel by elevator depending on the time of day and day of the week. Interpretation: Taking the stairs rather than the elevator saved about 15 minutes each workday. This 3% savings per workday could translate into improved productivity as well as increased fitness. PMID:22159365

Radiation chemistry of aqueous solutions of hydrazine at elevated temperatures: Pt. 2. Solutions containing oxygen

International Nuclear Information System (INIS)

Buxton, G.V.; Stuart, C.R.

1997-01-01

Here, we investigate the effects of oxygen on the radiation chemistry of hydrazine at elevated temperatures. The chemistry of this system is important to reactor coolant chemistry, particularly under start-up conditions when hydrazine is added to suppress corrosion which would otherwise be caused by the ingress of oxygen. The radiation chemistry of aqueous solutions of hydrazine has been investigated previously in the presence of oxygen by Ershov et al., but only at room temperature. In those experiments, both steady-state γ-radiolysis and pulse radiolysis were used to deduce the mechanism of decomposition of hydrazine in the presence of oxygen. (author)

Evolution of elevated containment temperatures at Calvert Cliffs Nuclear Power Plant

International Nuclear Information System (INIS)

Branch, R.D. Jr.

1991-01-01

In this paper the author describes the events which caused Calvert Cliffs Nuclear Power Plant engineers to recognize a need for monitoring of ambient temperatures within containment. The early attempts at temperature monitoring programs are discussed and critiqued. Primary failings of these early programs included a failure to collect temperature data under a variety of external conditions and a lack of quality assurance to make the data useful for design change. From these early attempts Calvert Cliffs developed a new, extensive temperature monitoring program designed to collect data over a two-year period. The author outlines the planned temperature monitoring program and discusses its expected results

Metallurgical evaluation of failed post-tensioned containment tendon anchors at Joseph M. Farley Unit 2

International Nuclear Information System (INIS)

Czajkowski, C.J.

1986-01-01

A metallurgical examination has been performed on three failed post-tensioned containment tendon anchors and one intact anchor from the Farley Unit 2 Nuclear Power Station. The evaluation consisted of chemical/mechanical testing, optical microscopy, scanning electron microscopy, and energy dispersive spectroscopy. The conclusions drawn from the investigation were: 1) the anchors met the chemical and mechanical properties of AISI 4140/4142 steel; 2) there was no evidence of phosphorous segregation to the grain boundary (by ethereal picral etch); 3) the observed cracking was generally a mixed mode of intergranular and quasi-cleavage as well as ductile rupture with the intergranular cracking occurring along prior austenite grain boundaries; 4) the results of the mechanical tests coupled with the discontinuous nature of the intergranular areas and the elimination of other modes of failure give sufficient indication that the failure was a hydrogen induced cracking phenomenon

Elevated CO2 stimulates marsh elevation gain, counterbalancing sea-level rise.

Science.gov (United States)

Langley, J Adam; McKee, Karen L; Cahoon, Donald R; Cherry, Julia A; Megonigal, J Patrick

2009-04-14

Tidal wetlands experiencing increased rates of sea-level rise (SLR) must increase rates of soil elevation gain to avoid permanent conversion to open water. The maximal rate of SLR that these ecosystems can tolerate depends partly on mineral sediment deposition, but the accumulation of organic matter is equally important for many wetlands. Plant productivity drives organic matter dynamics and is sensitive to global change factors, such as rising atmospheric CO(2) concentration. It remains unknown how global change will influence organic mechanisms that determine future tidal wetland viability. Here, we present experimental evidence that plant response to elevated atmospheric [CO(2)] stimulates biogenic mechanisms of elevation gain in a brackish marsh. Elevated CO(2) (ambient + 340 ppm) accelerated soil elevation gain by 3.9 mm yr(-1) in this 2-year field study, an effect mediated by stimulation of below-ground plant productivity. Further, a companion greenhouse experiment revealed that the CO(2) effect was enhanced under salinity and flooding conditions likely to accompany future SLR. Our results indicate that by stimulating biogenic contributions to marsh elevation, increases in the greenhouse gas, CO(2), may paradoxically aid some coastal wetlands in counterbalancing rising seas.

Elevated CO2 stimulates marsh elevation gain, counterbalancing sea-level rise

Science.gov (United States)

Langley, J. Adam; McKee, Karen L.; Cahoon, Donald R.; Cherry, Julia A.; Megonigal, J. Patrick

2009-01-01

Tidal wetlands experiencing increased rates of sea-level rise (SLR) must increase rates of soil elevation gain to avoid permanent conversion to open water. The maximal rate of SLR that these ecosystems can tolerate depends partly on mineral sediment deposition, but the accumulation of organic matter is equally important for many wetlands. Plant productivity drives organic matter dynamics and is sensitive to global change factors, such as rising atmospheric CO2 concentration. It remains unknown how global change will influence organic mechanisms that determine future tidal wetland viability. Here, we present experimental evidence that plant response to elevated atmospheric [CO2] stimulates biogenic mechanisms of elevation gain in a brackish marsh. Elevated CO2 (ambient + 340 ppm) accelerated soil elevation gain by 3.9 mm yr−1 in this 2-year field study, an effect mediated by stimulation of below-ground plant productivity. Further, a companion greenhouse experiment revealed that the CO2 effect was enhanced under salinity and flooding conditions likely to accompany future SLR. Our results indicate that by stimulating biogenic contributions to marsh elevation, increases in the greenhouse gas, CO2, may paradoxically aid some coastal wetlands in counterbalancing rising seas. PMID:19325121

Hanford Site waste management units report

International Nuclear Information System (INIS)

1993-04-01

The Hanford Site Waste Management Units Report was originated to provide information responsive to Section 3004(u) of the Hazardous and Solid Waste Amendments of the 1984. This report provides a comprehensive inventory of all types of waste management units at the Hanford Site, including a description of the units and the waste they contain. Waste management units in the report include: (1) Resource Conservation and Recovery Act of 1976 (RCRA) disposal units, (2) Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) disposal units, (3) unplanned releases, (4) inactive contaminated structures, (5) RCRA treatment, storage, and disposal (TSD) units, and (6) other storage areas. Because of the comprehensive nature of the units report, the list of units is more extensive than required by Section 3004(u) of Hazardous and Solid Waste Amendments of the 1984. In Sections 3.0 through 6.0 of this report, the four aggregate areas are subdivided into their operable units. The operable units are further divided into two parts: (1) those waste management units assigned to the operable unit that will be remediated as part of the Environmental Restoration Remedial Actions (ERRA) Program, and (2) those waste management units located within the operable unit boundaries but not assigned to the ERRA program. Only some operable unit sections contain the second part.Volume two contains Sections 4.0 through 6.0 and the following appendices: Appendix A -- acronyms and definition of terms; Appendix B -- unplanned releases that are not considered to be units; and Appendix C -- operable unit maps

Time of elevation of head of bed for patients receiving mechanical ventilation and its related factors.

Science.gov (United States)

Martí-Hereu, L; Arreciado Marañón, A

The semirecumbent position is a widespread recommendation for the prevention of pneumonia associated with mechanical ventilation. To identify the time of elevation of head of bed for patients under mechanical ventilation and the factors related to such elevation in an intensive care unit. An observational, descriptive cross-sectional study. Conducted in an intensive care unit of a tertiary hospital from April to June 2015. The studied population were mechanically ventilated patients. Daily hours in which patients remained with the head of the bed elevated (≥30°), socio-demographic data and clinical variables were recorded. 261 head elevation measurements were collected. The average daily hours that patients remained at ≥30° was 16h28' (SD ±5h38'), equivalent to 68.6% (SD ±23.5%) of the day. Factors related to elevations ≥30° for longer were: enteral nutrition, levels of deep sedation, cardiac and neurocritical diagnostics. Factors that hindered the position were: sedation levels for agitation and abdominal pathologies. Sex, age and ventilation mode did not show a significant relationship with bed head elevation. Although raising the head of the bed is an easy to perform, economical and measurable preventive measure, its compliance is low due to specific factors specific related o the patient's clinical condition. Using innovations such as continuous measurement of the head position helps to evaluate clinical practice and allows to carry out improvement actions whose impact is beneficial to the patient. Copyright © 2017 Sociedad Española de Enfermería Intensiva y Unidades Coronarias (SEEIUC). Publicado por Elsevier España, S.L.U. All rights reserved.

Effects of Si on microstructure and phase transformation at elevated temperatures in ferritic white cast irons

Energy Technology Data Exchange (ETDEWEB)

Wiengmoon, A., E-mail: ampornw@nu.ac.th [Department of Physics, Faculty of Science, Naresuan University, Phitsanulok 65000 (Thailand); Pearce, J.T.H. [Panyapiwat Institute of Management, Nonthaburi 11120 (Thailand); Nusen, S.; Chairuangsri, T. [Department of Industrial Chemistry, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand)

2016-10-15

The effects of Si on microstructure and phase transformation at elevated temperature of ferritic 31wt.%Cr-1.1wt.%C white cast irons with up to 3wt.%Si have been studied. Applications of these irons include parts requiring heat resistance at elevated temperature. The irons were produced by sand casting. The microstructure in as-cast condition and after being subjected to high temperature (700 to 1000 °C) was investigated by light microscopy, X-ray diffraction, and electron microscopy. The results revealed that the as-cast microstructure consisted mainly of primary ferrite dendrites and eutectic (ferrite + M{sub 7}C{sub 3}). Si promotes M{sub 7}C{sub 3}-to-M{sub 23}C{sub 6} transformation in the irons subjected to transformation at elevated temperature, but no sigma phase was found. The extent of M{sub 7}C{sub 3}-to-M{sub 23}C{sub 6} transformation increases proportional to the increasing transformation temperature, holding time and Si content in the irons. For the iron with 1.0wt.%Si content after holding at elevated temperatures, martensite was also found, which could be attributed to carbon accretion effects in eutectic ferrite. Si was incorporated in M{sub 23}C{sub 6} such that M{sub 23}C{sub 6} containing Si can show darker contrast under SEM-BEI as compared to M{sub 7}C{sub 3}; this is the opposite to what has been observed for the cases of typical M{sub 23}C{sub 6} and M{sub 23}C{sub 6} containing Mo or W. The results obtained are important to understand the change in properties of ferritic, high chromium irons containing Si subjected to elevated temperature.

ST Elevations and Elevated Cardiac Enzymes Not Always a STEMI: Two Case Reports.

Science.gov (United States)

Fernández Fernández, Juan; Deliz-Guzmán, Claudia; Andino-Colón, César; Claudio-Hernández, Héctor; Lugo-Amador, Nannette

2016-01-01

Chest pain is a common complaint in the emergency department (ED). Besides a careful history and physical exam; electrocardiogram, laboratory tests and imaging studies are widely available diagnostic tests that are used for patient assessment. When ST elevation and elevated cardiac enzymes are present the most likely diagnosis are ST elevation myocardial infarction (STEMI) or myocarditis. In this case report we present two low risk patients for major adverse cardiac event with ST elevation and elevated cardiac enzymes and how a careful risk assessment and detailed electrocardiogram evaluation could help differentiating between these two diagnoses.

Reproductive allometry in Pedicularis species changes with elevation

DEFF Research Database (Denmark)

Guo, Hui; Weiner, Jacob; Mazer, Susan J.

2012-01-01

1. Plants produce biomass and then allocate some of it to reproductive structures, so the relationship between reproductive (R) and vegetative (V) mass is a fundamental aspect of a plant’s reproductive strategy. 2. Differences among populations or taxa in the allometric relationship between R and V...... reproductive allocation at smaller sizes and a smaller investment in reproduction per additional unit of biomass accumulated. 3. We investigated variation in the allometric relationship between R and V among 44 naturally occurring populations representing 24 species of Pedicularis in the Tibetan Plateau...... at smaller sizes and less at larger sizes than plants growing at lower elevations. 5. Synthesis. The allometric slope (exponent) of the R–V relationship decreases with increasing elevation among Pedicularis populations and species, reflecting fundamental changes in the costs and benefits of increased...

National Elevation Dataset (NED)

Data.gov (United States)

Kansas Data Access and Support Center — The U.S. Geological Survey has developed a National Elevation Database (NED). The NED is a seamless mosaic of best-available elevation data. The 7.5-minute elevation...

Varied growth response of cogongrass ecotypes to elevated CO2

Directory of Open Access Journals (Sweden)

G. Brett Runion

2016-01-01

Full Text Available Cogongrass [Imperata cylindrica (L. P. Beauv] is an invasive C4 perennial grass which is listed as one of the top ten worst weeds in the world and is a major problem in the Southeast US. Five cogongrass ecotypes (Florida, Hybrid, Louisiana, Mobile, and North Alabama collected across the Southeast and a red-tip ornamental variety were container grown for six months in open top chambers under ambient and elevated (ambient plus 200 ppm atmospheric CO2. Elevated CO2 increased average dry weight (13% which is typical for grasses. Elevated CO2 increased height growth and both nitrogen and water use efficiencies, but lowered tissue nitrogen concentration; again, these are typical plant responses to elevated CO2. The hybrid ecotype tended to exhibit the greatest growth (followed by Louisiana, North Alabama, and Florida ecotypes while the red-tip and Mobile ecotypes were smallest. Interactions of CO2 with ecotype generally showed that the hybrid, Louisiana, Florida, and/or North Alabama ecotypes showed a positive response to CO2 while the Mobile and red-tip ecotypes did not. Cogongrass is a problematic invasive weed in the southeastern U.S. and some ecotypes may become more so as atmospheric CO2 continues to rise.

Climate Change Altered Disturbance Regimes in High Elevation Pine Ecosystems

Science.gov (United States)

Logan, J. A.

2004-12-01

Insects in aggregate are the greatest cause of forest disturbance. Outbreaks of both native and exotic insects can be spectacular events in both their intensity and spatial extent. In the case of native species, forest ecosystems have co-evolved (or at least co-adapted) in ways that incorporate these disturbances into the normal cycle of forest maturation and renewal. The time frame of response to changing climate, however, is much shorter for insects (typically one year) than for their host forests (decades or longer). As a result, outbreaks of forest insects, particularly bark beetles, are occurring at unprecedented levels throughout western North America, resulting in the loss of biodiversity and potentially entire ecosystems. In this talk, I will describe one such ecosystem, the whitebark pine association at high elevations in the north-central Rocky Mountains of the United States. White bark pines are keystone species, which in consort with Clark's nutcracker, build entire ecosystems at high elevations. These ecosystems provide valuable ecological services, including the distribution and abundance of water resources. I will briefly describe the keystone nature of whitebark pine and the historic role of mountain pine beetle disturbance in these ecosystems. The mountain pine beetle is the most important outbreak insect in forests of the western United States. Although capable of spectacular outbreak events, in historic climate regimes, outbreak populations were largely restricted to lower elevation pines; for example, lodgepole and ponderosa pines. The recent series of unusually warm years, however, has allowed this insect to expand its range into high elevation, whitebark pine ecosystems with devastating consequences. The aspects of mountain pine beetle thermal ecology that has allowed it to capitalize so effectively on a warming climate will be discussed. A model that incorporates critical thermal attributes of the mountain pine beetle's life cycle was

Hanford Site Waste Management Units Report

Energy Technology Data Exchange (ETDEWEB)

Shearer, Jeffrey P. [Hanford Site (HNF), Richland, WA (United States)

2012-02-29

The Hanford Site Waste Management Units Report (HSWMUR) has been created to meet the requirements of the Tri-Party Agreement (TPA) Action Plan, Section 3.5, which states: “The Hanford Site Waste Management Units Report shall be generated, in a format agreed upon by the Parties, as a calendar year report and issued annually by the DOE by the end of February of each year, and posted electronically for regulator and public access. This report shall reflect all changes made in waste management unit status during the previous year.” This February 2012 version of the HSWMUR contains a comprehensive inventory of the 3389 sites and 540 subsites in the Waste Information Data System (WIDS). The information for each site contains a description of each unit and the waste it contains, where applicable. The WIDS database provides additional information concerning the sites contained in this report and is maintained with daily changes to these sites.

Hanford Site Waste Management Units Report

Energy Technology Data Exchange (ETDEWEB)

Shearer, Jeffrey P. [Hanford Site (HNF), Richland, WA (United States)

2013-02-13

The Hanford Site Waste Management Units Report (HSWMUR) has been created to meet the requirements of the Tri-Party Agreement (TPA) Action Plan, Section 3.5, which states: “The Hanford Site Waste Management Units Report shall be generated, in a format agreed upon by the Parties, as a calendar year report and issued annually by the DOE by the end of February of each year, and posted electronically for regulator and public access. This report shall reflect all changes made in waste management unit status during the previous year.” This February 2013 version of the HSWMUR contains a comprehensive inventory of the 3427 sites and 564 subsites in the Waste Information Data System (WIDS). The information for each site contains a description of each unit and the waste it contains, where applicable. The WIDS database provides additional information concerning the sites contained in this report and is maintained with daily changes to these sites.

Hanford Site Waste Management Units Report

Energy Technology Data Exchange (ETDEWEB)

Shearer, Jeffrey P. [Hanford Site (HNF), Richland, WA (United States)

2014-02-19

The Hanford Site Waste Management Units Report (HSWMUR) has been created to meet the requirements of the Tri-Party Agreement (TPA) Action Plan, Section 3.5, which states: “The Hanford Site Waste Management Units Report shall be generated, in a format agreed upon by the Parties, as a calendar year report and issued annually by the DOE by the end of February of each year, and posted electronically for regulator and public access. This report shall reflect all changes made in waste management unit status during the previous year.” This February 2013 version of the HSWMUR contains a comprehensive inventory of the 3438 sites and 569 subsites in the Waste Information Data System (WIDS). The information for each site contains a description of each unit and the waste it contains, where applicable. The WIDS database provides additional information concerning the sites contained in this report and is maintained with daily changes to these sites.

Ionic Liquids as templating agents in formation of uranium-containing nanomaterials

Science.gov (United States)

Visser, Ann E; Bridges, Nicholas J

2014-06-10

A method for forming nanoparticles containing uranium oxide is described. The method includes combining a uranium-containing feedstock with an ionic liquid to form a mixture and holding the mixture at an elevated temperature for a period of time to form the product nanoparticles. The method can be carried out at low temperatures, for instance less than about 300.degree. C.

A mitotically inheritable unit containing a MAP kinase module.

Science.gov (United States)

Kicka, Sébastien; Bonnet, Crystel; Sobering, Andrew K; Ganesan, Latha P; Silar, Philippe

2006-09-05

Prions are novel kinds of hereditary units, relying solely on proteins, that are infectious and inherited in a non-Mendelian fashion. To date, they are either based on autocatalytic modification of a 3D conformation or on autocatalytic cleavage. Here, we provide further evidence that in the filamentous fungus Podospora anserina, a MAP kinase cascade is probably able to self-activate and generate C, a hereditary unit that bears many similarities to prions and triggers cell degeneration. We show that in addition to the MAPKKK gene, both the MAPKK and MAPK genes are necessary for the propagation of C, and that overexpression of MAPK as that of MAPKKK facilitates the appearance of C. We also show that a correlation exists between the presence of C and localization of the MAPK inside nuclei. These data emphasize the resemblance between prions and a self-positively regulated cascade in terms of their transmission. This thus further expands the concept of protein-base inheritance to regulatory networks that have the ability to self-activate.

Geographic distribution of dementia mortality: elevated mortality rates for black and white Americans by place of birth.

Science.gov (United States)

Glymour, M Maria; Kosheleva, Anna; Wadley, Virginia G; Weiss, Christopher; Manly, Jennifer J

2011-01-01

We hypothesized that patterns of elevated stroke mortality among those born in the United States Stroke Belt (SB) states also prevailed for mortality related to all-cause dementia or Alzheimer Disease. Cause-specific mortality (contributing cause of death, including underlying cause cases) rates in 2000 for United States-born African Americans and whites aged 65 to 89 years were calculated by linking national mortality records with population data based on race, sex, age, and birth state or state of residence in 2000. Birth in a SB state (NC, SC, GA, TN, AR, MS, or AL) was cross-classified against SB residence at the 2000 Census. Compared with those who were not born in the SB, odds of all-cause dementia mortality were significantly elevated by 29% for African Americans and 19% for whites born in the SB. These patterns prevailed among individuals who no longer lived in the SB at death. Patterns were similar for Alzheimer Disease-related mortality. Some non-SB states were also associated with significant elevations in dementia-related mortality. Dementia mortality rates follow geographic patterns similar to stroke mortality, with elevated rates among those born in the SB. This suggests important roles for geographically patterned childhood exposures in establishing cognitive reserve.

Storage chamber for container of radiation-contaminated material

International Nuclear Information System (INIS)

Takakura, Masahide.

1996-01-01

The present invention concerns a storage chamber for containing radiation-contaminated materials in containing tubes and having cooling fluids circulated at the outer side of the containing tubes. The storage chamber comprises a gas supply means connected to the inside of the container tube for supplying a highly heat-conductive gas and a gas exhaustion means for discharging the gas present in the container tube. When containing vessels for radiation-contaminated materials are contained in the container tube, the gases present inside of the container tube is exhausted by means of the gas exhaustion means, and highly heat conductive gases are filled from the gas supply means to the space between the container tube and the containing vessels for the radiation-contaminated materials. When the temperature of the highly heat conductive gas is elevated due to the heat generation of the radiation-contaminated materials, the container tube is heated, and then cooled by the cooling fluid at the outer side of the container tube. In this case, the heat of the radiation-contaminated material-containing vessels is removed by the heat conduction by the highly heat conductive gas to reduce temperature gradient between the containing vessels and the containing tube. This can enhance the cooling effect. (T.M.)

Effects of elevated CO2 and vascular plants on evapotranspiration in bog vegetation

NARCIS (Netherlands)

Heijmans, M.M.P.D.; Arp, W.J.; Berendse, F.

2001-01-01

We determined evapotranspiration in three experiments designed to study the effects of elevated CO2 and increased N deposition on ombrotrophic bog vegetation. Two experiments used peat monoliths with intact bog vegetation in containers, with one experiment outdoors and the other in a greenhouse. A

Reactor containment and reactor safety in the United States

International Nuclear Information System (INIS)

Kouts, H.

1986-01-01

The reactor safety systems of two reactors are studied aiming at the reactor containment integrity. The first is a BWR type reactor and is called Peachbottom 2, and the second is a PWR type reactor, and is called surry. (E.G.) [pt

Conducting water chemistry of the secondary coolant circuit of VVER-based nuclear power plant units constructed without using copper containing alloys

Science.gov (United States)

Tyapkov, V. F.

2014-07-01

The secondary coolant circuit water chemistry with metering amines began to be put in use in Russia in 2005, and all nuclear power plant units equipped with VVER-1000 reactors have been shifted to operate with this water chemistry for the past seven years. Owing to the use of water chemistry with metering amines, the amount of products from corrosion of structural materials entering into the volume of steam generators has been reduced, and the flow-accelerated corrosion rate of pipelines and equipment has been slowed down. The article presents data on conducting water chemistry in nuclear power plant units with VVER-1000 reactors for the secondary coolant system equipment made without using copper-containing alloys. Statistical data are presented on conducting ammonia-morpholine and ammonia-ethanolamine water chemistries in new-generation operating power units with VVER-1000 reactors with an increased level of pH. The values of cooling water leaks in turbine condensers the tube system of which is made of stainless steel or titanium alloy are given.

Conjugated Polymers Containing BODIPY and Fluorene Units for Sensitive Detection of CN− Ions: Site-Selective Synthesis, Photo-Physical and Electrochemical Properties

Directory of Open Access Journals (Sweden)

Tian He

2017-10-01

Full Text Available Conjugated polymers containing distinct molecular units are expected to be very interesting because of their unique properties endowed by these units and the formed conjugated polymers. Herein, four new conjugated copolymers based on fluorene and 4,4’-difluoro-4-bora-3a,4a-diaza-s-indacene (BODIPY have been designed and synthesized via Sonogashira polymerization. The fluorene unit was attached to the 3,5- or 2,6-positions of BODIPY by ethynylenes or p-diacetylenebenzene. The obtained polymers show good thermal stability and broad absorption in the wavelength range from 300 to 750 nm. The effects of site-selective copolymerization and conjugation length along the polymer backbone on the optoelectronic and electrochemical properties of these copolymers were systematically studied by UV-Vis spectroscopy, photoluminescence (PL and cyclic voltammetry. Besides, it is found that the BODIPY-based copolymers exhibit selectively sensitive responses to cyanide anions, resulting in obvious change of UV-Vis absorption spectra and significant fluorescence quenching of the polymers among various common anions.

Easy steel tower elevation. Development of a steel tower elevating aiding device; Tetto shoko wo rakuraku to. Tetto shoko hojo sochi no kaihatsu ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Tobe, Y. [Kansai Electric Power Co. Inc., Osaka (Japan)

1999-02-10

Elevation of a transmission line steel tower is performed by an operator`s own force upon fixing a safety device to prevent a fall on a safety wire (SW) previously installed on a specified tower leg. It is a considerable burden for the operator to move the tower having a height of 80 to 100 m up and down several times a day. In order to reduce the fatigue, a portable, small and light-weight steel tower elevation aiding device was developed. The existing SW is used to fix the device, requiring no additional facility to be fixed on the tower. Safety assurance depends on the safety device on the SW as currently used. The device has pulling force of 50 kgf (the device operates in a range of 4 to 50 kgf to assure workability in elevation and stopping), and elevation speed of 15 to 20 m/minute (equivalent to the present work. The braking force can be adjusted in three steps at descent according to the ability of the operator). An Ni-hydrogen battery is used, capable of two returns on a tower per charge. Considering the device to be transported in mountainous area, the shape is such that a single unit can be put into a backpack. The device can also be used in general construction sites. (NEDO)

Significantly Elevated Serum Lipase in Pregnancy with Nausea and Vomiting: Acute Pancreatitis or Hyperemesis Gravidarum?

Directory of Open Access Journals (Sweden)

Amanda Johnson

2015-01-01

Full Text Available Hyperemesis gravidarum is a severe manifestation of nausea and vomiting of pregnancy and it is associated with weight loss and metabolic abnormalities. It is known that abnormal laboratory values, including mildly elevated serum lipase level, could be associated with hyperemesis gravidarum. However, in this case report details of two women with hyperemesis gravidarum but with significantly elevated serum lipase levels were discussed. These patients presented with severe nausea and vomiting but without abdominal pain. They were found to have severely elevated lipase levels over 1,000 units/liter. In the absence of other findings of pancreatitis, they were treated with conservative measures for hyperemesis gravidarum, with eventual resolution to normal lipase levels. Although significantly elevated lipase level in pregnant patients with nausea and vomiting is a concern for acute pancreatitis, these two cases of significantly elevated serum lipase without other clinical findings of pancreatitis led to this report that serum lipase could be quite elevated in hyperemesis gravidarum and that it might not be an accurate biochemical marker for acute pancreatitis. Imaging studies are thus necessary to establish the diagnosis of acute pancreatitis.

Design considerations for CRBRP heat transport system piping operating at elevated temperatures

International Nuclear Information System (INIS)

Pollono, L.P.; Mello, R.M.

1979-01-01

The heat transport system sodium piping for the Clinch River Breeder Reactor Plant (CRBRP) within the reactor containment building must withstand high temperatures for long periods of time. Each phase of the mechanical design process of the piping system is influenced by elevated temperature considerations which include material thermal creep effects, ratchetting caused by rapid temperature transients and stress relaxation, and material degradation effects. The structural design philosophy taken to design the CRBRP piping operating in a high temperature environment is described. The resulting design of the heat transport system piping is presented along with a discussion of special features that resulted from the elevated temperature considerations

Indsatser for tosprogede elever

DEFF Research Database (Denmark)

Andersen, Dines; Jakobsen, Vibeke; Jensen, Vibeke Myrup

Fagligt set klarer tosprogede elever sig dårligere i skolen og det videre uddannelsessystem end ’danske’ elever. Kommuner og folkeskoler har derfor sat en række tiltag i værk, som sigter mod at forbedre de tosprogede elevers skole- og uddannelsessituation. Rapporten kortlægger og analyserer...... af klasseundervisningen. Analysen viser, at de elever, der bliver taget ud af klassen for at få ekstra undervisning i dansk som andetsprog, klarer sig dårligere end elever, der modtager ekstraundervisningen i klassen eller uden for skoletid. Undersøgelsen er baseret på spørgeskemaundersøgelser blandt...... kommunale forvaltningschefer, skoleledere, lærere og forældre til børn i 2. klasse samt lærere til og elever i 9. klasse, SFI’s forløbsundersøgelse af årgang 1995 og registerdata. Undersøgelsen er via Ministeriet for Børn og Undervisning betalt med midler fra satspuljeaftalen 2009 om integration....

Cementitious porous pavement in stormwater quality control: pH and alkalinity elevation.

Science.gov (United States)

Kuang, Xuheng; Sansalone, John

2011-01-01

A certain level of alkalinity acts as a buffer and maintains the pH value in a stable range in water bodies. With rapid urban development, more and more acidic pollutants flow to watersheds with runoff and drop alkalinity to a very low level and ultimately degrade the water environment. Cementitious porous pavement is an effective tool for stormwater acidic neutralization. When stormwater infiltrates cement porous pavement (CPP) materials, alkalinity and pH will be elevated due to the basic characteristics of cement concrete. The elevated alkalinity will neutralize acids in water bodies and maintain the pH in a stable level as a buffer. It is expected that CPP materials still have a certain capability of alkalinity elevation after years of service, which is important for CPP as an effective tool for stormwater management. However, few previous studies have reported on how CPP structures would elevate runoff alkalinity and pH after being exposed to rainfall-runoff for years. In this study, three groups of CPP specimens, all exposed to rainfall-runoff for 3 years, were used to test the pH and alkalinity elevation properties. It was found that runoff pH values were elevated from 7.4 to the range of 7.8-8.6 after infiltrating through the uncoated specimens, and from 7.4 to 8.5-10.7 after infiltrating through aluminum-coated specimens. Runoff alkalinity elevation efficiencies are 11.5-14.5% for uncoated specimens and 42.2% for coated specimens. The study shows that CPP is an effective passive unit operation for stormwater acid neutralization in our built environment.

Reducing elevator energy use: A comparison of posted feedback and reduced elevator convenience

Science.gov (United States)

Houten, Ron Van; Nau, Paul A.; Merrigan, Michael

1981-01-01

The effects of two different procedures for reducing elevator energy use were assessed using a multiple-baseline design. In the first procedure, feedback about the amount of energy consumed by the elevators each week was posted on each elevator door. Later, signs advocating the use of stairs to save energy and improve health were posted next to the feedback signs. In the second procedure, the time required to travel between floors was increased by adding a delay to the elevator door closing mechanisms. Results indicated that neither feedback alone nor feedback plus educational signs reduced the amount of energy consumed by the elevators. However, use of the door delay reduced consumption by one-third in all elevators. A second experiment replicated the effect of the door delay on energy consumption and, in addition, demonstrated that the door delay also produced a reduction in the number of persons using the elevator. The second experiment also showed that, following an initial period during which a full delay was in effect, a gradual reduction of the delay interval resulted in continued energy conservation. Reduced convenience as a general strategy for energy conservation is discussed. PMID:16795648

High speed elevator s rise high rise building; Chokoso biru wo kakenoboru elevator

Energy Technology Data Exchange (ETDEWEB)

Tanabe, K. [Mitsubishi Electric Corp., Tokyo (Japan)

1994-10-20

The world`s fastest (750 m/min) elevators are operating in Yokohama Landmark Tower. This paper describes how engineers solved the technological problems to realize the high-speed elevator. Buildings in Japan have become higher and higher. At the present, this Tower is the highest in Japan (296 m, 70 stories). The Ministry of Construction is going to start a research team to study construction of buildings of the order of 1,000 m high. An important issue for a skyscraper is how to reduce the elevator space adapting to the increase of the number of inhabitants in the building. The basic solution is to increase the elevator speed and to plan the best elevator moving line. The 120 kW AC motor direct-driven winding machine that withstands the superhigh-speed suspending load was developed. Vibrations from the motor and the mechanical system are minimized and the touch-down tolerances for the elevator cage are controlled to {plus_minus}15 mm. The safety devices of the elevator include the emergency stopper of special ceramic material and the hydraulic shock absorber with the optimum reduction characteristic. 2 refs., 3 figs.

Review and evaluation of the Millstone Unit 3 probabilistic safety study. Containment failure modes, radiological source - terms and offsite consequences

International Nuclear Information System (INIS)

Khatib-Rahbar, M.; Pratt, W.; Ludewig, H.

1985-09-01

A technical review and evaluation of the Millstone Unit 3 probabilistic safety study has been performed. It was determined that; (1) long-term damage indices (latent fatalities, person-rem, etc.) are dominated by late failure of the containment, (2) short-term damage indices (early fatalities, etc.) are dominated by bypass sequences for internally initiated events, while severe seismic sequences can also contribute significantly to early damage indices. These overall estimates of severe accident risk are extremely low compared with other societal sources of risk. Furthermore, the risks for Millstone-3 are comparable to risks from other nuclear plants at high population sites. Seismically induced accidents dominate the severe accident risks at Millstone-3. Potential mitigative features were shown not to be cost-effective for internal events. Value-impact analysis for seismic events showed that a manually actuated containment spray system might be cost-effective

Container for hydrogen isotopes

Energy Technology Data Exchange (ETDEWEB)

1976-01-12

A container is described for storage, shipping and and dispensing of hydrogen isotopes such as hydrogen, deuterium, tritium, or mixtures of the same. The container is compact, safe against fracture or accident, and is reusable. It consists of an outer housing with suitable inlet and outlet openings and electrical feed elements, the housing containing an activated sorber material in the form, for example of titanium sponge or an activated zirconium aluminate cartridge. The gas to be stored is introduced into the chamber under conditions of heat and vacuum and is retained in the sorber material. Subsequently, it may be released by heating the unit to drive off the stored gas at desired rates.

Container for hydrogen isotopes

International Nuclear Information System (INIS)

1976-01-01

A container is described for storage, shipping and and dispensing of hydrogen isotopes such as hydrogen, deuterium, tritium, or mixtures of the same. The container is compact, safe against fracture or accident, and is reusable. It consists of an outer housing with suitable inlet and outlet openings and electrical feed elements, the housing containing an activated sorber material in the form, for example of titanium sponge or an activated zirconium aluminate cartridge. The gas to be stored is introduced into the chamber under conditions of heat and vacuum and is retained in the sorber material. Subsequently, it may be released by heating the unit to drive off the stored gas at desired rates

Container for hydrogen isotopes

International Nuclear Information System (INIS)

Solomon, D.E.

1977-01-01

A container for the storage, shipping and dispensing of hydrogen isotopes such as hydrogen, deuterium, tritium, or mixtures of the same which has compactness, which is safe against fracture or accident, and which is reusable is described. The container consists of an outer housing with suitable inlet and outlet openings and electrical feed elements, the housing containing an activated sorber material in the form, for example, of titanium sponge or an activated zirconium aluminate cartridge. The gas to be stored is introduced into the chamber under conditions of heat and vacuum and will be retained in the sorber material. Subsequently, it may be released by heating the unit to drive off the stored gas at desired rates

Neutron spectrum measurement inside containment vessel at Kori nuclear power plant unit 1

Energy Technology Data Exchange (ETDEWEB)

Han, J. M.; Kim, T. W.; Kim, K. D.; Youn, C. H. [Nuclear Environment Technology Institute, Taejon (Korea, Republic of)

2003-10-01

There would be a case for the radiation worker have to work inside of the containment vessel to inspect or repair reactor facilities. In this case, the information about distribution of neutron field is needed to estimate neutron exposure dose of worker. Neutron spectra were measured by BMS(Bonner Multisphere Spectrometer) at 4 points of 6 ft and 20 ft, 2 points of 44 ft, 5 points of 70 ft in containment vessel of Kori unit 1. From the calculation, the following results were obtained. Neutron fluxes of 6 ft were between 2.623 x 10{sup 2} and 2.746 x 10{sup 4} neutron/cm{sup 2}{center_dot}sec, average neutron energies were between 9.209 x 10{sup -6} and 3.377 x 10{sup -2} MeV, equivalent doses of neutron were between 0.025 and 2.675 mSv/hr. Neutron fluxes of 20 ft were between 1.771 x 10{sup 1} and 1.682 x 10{sup 3} neutron/cm{sup 2}{center_dot}sec, average neutron energies were between 6.084 x 10{sup -6} and 2.988 x 10{sup -1} MeV, equivalent doses of neutron were between 0.004 and 0.228 mSv/hr. Neutron fluxes of 44 ft were between 3.367 x 10{sup 2} and 3.483 x 10{sup 2} neutron / cm{sup 2}{center_dot}sec, average neutron energies were between 3.962 x 10{sup -2} and 7.360 x 10{sup -2} MeV, equivalent doses of neutron were between 0.069 and 0.089 mSv/hr. Neutron fluxes of 70 ft were between 4.553 x 10{sup 3} and 1.407 x 10{sup 4} neutron/cm{sup 2}{center_dot}sec, average neutron energies were between 3.668 x 10{sup -4} and 6.764 x 10{sup -2} MeV, equivalent doses of neutron were between 0.449 and 2.660 mSv/hr.

Lærer-elev-relationer

DEFF Research Database (Denmark)

Laursen, Per Fibæk; Nielsen, Anne Maj

2015-01-01

I kapitlet belyser vi relationskompetence i forholdet mellem lærer og elever og hvordan læreren kan arbejde med forhold til elever og med sin opmærksomhed på relationsarbejdet. Afslutningsvis ser vi på hvordan lærere fortsat kan udvikle deres relationskompetence.......I kapitlet belyser vi relationskompetence i forholdet mellem lærer og elever og hvordan læreren kan arbejde med forhold til elever og med sin opmærksomhed på relationsarbejdet. Afslutningsvis ser vi på hvordan lærere fortsat kan udvikle deres relationskompetence....

Material containment enclosure

International Nuclear Information System (INIS)

Carlson, D.O.

1993-01-01

An isolation enclosure and a group of isolation enclosures are described which are useful when a relatively large containment area is required. The enclosure is in the form of a ring having a section removed so that a technician may enter the center area of the ring. In a preferred embodiment, an access zone is located in the transparent wall of the enclosure and extends around the inner perimeter of the ring so that a technician can insert his hands into the enclosure to reach any point within. The inventive enclosures provide more containment area per unit area of floor space than conventional material isolation enclosures. 3 figures

Commercial disposal of High Integrity Containers (HICs) containing EPICOR-II prefilters from Three Mile Island

International Nuclear Information System (INIS)

McConnell, J.W. Jr.; Lynch, R.J.; Tyacke, M.J.

1985-09-01

This report describes the processes of loading, transporting, and commercially disposing of 45 High Integrity Containers (HICs), each containing an EPICOR-II prefilter. Also described are the improvements that were applied in the disposition of the 45 commercial EPICOR-II prefilters at the Idaho National Engineering Laboratory (INEL), versus those used for the demonstration unit. The significance of this effort was that the commercial disposal campaign involved the first-of-a-kind production use of a reinforced concrete HIC at the US Ecology, Inc. facility in the State of Washington. This allowed for safe disposal of high-specific-activity ion exchange material in EPICOR-II prefilters generated during the cleanup of the Unit-2 Auxiliary and Fuel Handling Building of the Three Mile Island Nuclear Power Station. 26 figs

Cerebral Pulsatility Index Is Elevated in Patients with Elevated Right Atrial Pressure.

Science.gov (United States)

Lahiri, Shouri; Schlick, Konrad H; Padrick, Matthew M; Rinsky, Brenda; Gonzalez, Nestor; Jones, Heather; Mayer, Stephan A; Lyden, Patrick D

2018-01-01

Extracerebral venous congestion can precipitate intracranial hypertension due to obstruction of cerebral blood outflow. Conditions that increase right atrial pressure, such as hypervolemia, are thought to increase resistance to jugular venous outflow and contribute to cerebro-venous congestion. Cerebral pulsatility index (CPI) is considered a surrogate marker of distal cerebrovascular resistance and is elevated with intracranial hypertension. Thus, we sought to test the hypothesis that elevated right atrial pressure is associated with increased CPI compared to normal right atrial pressure. We retrospectively reviewed 61 consecutive patients with subarachnoid hemorrhage. We calculated CPI from transcranial Doppler studies and correlated these with echocardiographic measures of right atrial pressure. CPIs were compared from patients with elevated and normal right atrial pressure. There was a significant difference between CPI obtained from all patients with elevated right atrial pressure compared to those with normal right atrial pressure (P right and left hemispheric CPI from patients with both elevated and normal right atrial pressure. Patients with elevated right atrial pressure had significantly higher CPI compared to patients with normal right atrial pressure. These findings suggest that cerebro-venous congestion due to impaired jugular venous outflow may increase distal cerebrovascular resistance as measured by CPI. Since elevated CPI is associated with poor outcome in numerous neurological conditions, future studies are needed to elucidate the significance of these results in other populations. Copyright © 2017 by the American Society of Neuroimaging.

Development on design methodology of PWR passive containment system

International Nuclear Information System (INIS)

Lee, Seong Wook

1998-02-01

The containment is the most important barrier against the release of radioactive materials into the environment during accident conditions of nuclear power plants. Therefore the development of a reliable containment cooling system is one of key areas in advanced reactor development. To enhance the safety of the containment system, many new containment system designs have been proposed and developed in the world. Several passive containment cooling system (PCCS) concepts for both steel and concrete containment systems are overviewed and assessed comparatively. Major concepts considered are: (a) the spray of water on the outer surface of a steel containment from an elevated tank, (b) an external moat for a steel containment, (c) a suppression pool for a concrete containment, and (d) combination of the internal spray and internal or external condensers for a concrete containment. Emphasis is given to the heat removal principles, the required heat transfer area, system complexity and operational reliability. As one of conceptual design steps of containment, a methodology based on scaling principles is proposed to determine the containment size according to the power level. The AP600 containment system is selected as the reference containment to which the scaling laws are applied. Governing equations of containment pressure are set up in consideration of containment behavior in accident conditions. Then, the dimensionless numbers, which characterize the containment phenomena, are derived for the blowdown dominant and decay heat dominant stage, respectively. The important phenomena in blowdown stage are mass and energy sources and their absorption in containment atmosphere or containment structure, while heat transfer to the outer environment becomes important in decay heat stage. Based on their similarity between the prototype and the model, the containment sizes are determined for higher power levels and are compared with the SPWR containment design values available

Durable zinc oxide-containing sorbents for coal gas desulfurization

Science.gov (United States)

Siriwardane, Ranjani V.

1996-01-01

Durable zinc-oxide containing sorbent pellets for removing hydrogen sulfide from a gas stream at an elevated temperature are made up to contain titania as a diluent, high-surface-area silica gel, and a binder. These materials are mixed, moistened, and formed into pellets, which are then dried and calcined. The resulting pellets undergo repeated cycles of sulfidation and regeneration without loss of reactivity and without mechanical degradation. Regeneration of the pellets is carried out by contacting the bed with an oxidizing gas mixture.

The StreamCat Dataset: Accumulated Attributes for NHDPlusV2 (Version 2.1) Catchments for the Conterminous United States: National Elevation Dataset

Data.gov (United States)

U.S. Environmental Protection Agency — This dataset represents the elevation values within individual local NHDPlusV2 catchments and upstream, contributing watersheds based on the National Elevation...

Slitrk1-deficient mice display elevated anxiety-like behavior and noradrenergic abnormalities.

Science.gov (United States)

Katayama, K; Yamada, K; Ornthanalai, V G; Inoue, T; Ota, M; Murphy, N P; Aruga, J

2010-02-01

Mutations in SLITRK1 are found in patients with Tourette's syndrome and trichotillomania. SLITRK1 encodes a transmembrane protein containing leucine-rich repeats that is produced predominantly in the nervous system. However, the role of this protein is largely unknown, except that it can modulate neurite outgrowth in vitro. To clarify the role of Slitrk1 in vivo, we developed Slitrk1-knockout mice and analyzed their behavioral and neurochemical phenotypes. Slitrk1-deficient mice exhibited elevated anxiety-like behavior in the elevated plus-maze test as well as increased immobility time in forced swimming and tail suspension tests. Neurochemical analysis revealed that Slitrk1-knockout mice had increased levels of norepinephrine and its metabolite 3-methoxy-4-hydroxyphenylglycol. Administration of clonidine, an alpha2-adrenergic agonist that is frequently used to treat patients with Tourette's syndrome, attenuated the anxiety-like behavior of Slitrk1-deficient mice in the elevated plus-maze test. These results lead us to conclude that noradrenergic mechanisms are involved in the behavioral abnormalities of Slitrk1-deficient mice. Elevated anxiety due to Slitrk1 dysfunction may contribute to the pathogenesis of neuropsychiatric diseases such as Tourette's syndrome and trichotillomania.

An elevator

Energy Technology Data Exchange (ETDEWEB)

Loginovskiy, V.I.; Medinger, N.V.; Rasskazov, V.A.; Solonitsyn, V.A.

1983-01-01

An elevator is proposed which includes a body, spring loaded cams and a shut-off ring. To increase the reliability of the elevator by eliminating the possibility of spontaneous shifting of the shut-off ring, the latter is equipped with handles hinged to it and is made with evolvent grooves. The cams are equipped with rollers installed in the evolvent grooves of the shut off ring, where the body is made with grooves for the handles.

Containment bellows testing under extreme loads

International Nuclear Information System (INIS)

Splezter, B.L.; Lambert, L.D.; Parks, M.B.

1993-01-01

Sandia National Laboratories (SNL) is conducting several research programs to help develop validated methods for the prediction of the ultimate pressure capacity, at elevated temperatures, of light water reactor (LWR) containment structures. To help understand the ultimate pressure of the entire containment pressure boundary, each component must be evaluated. The containment pressure boundary consists of the containment shell and many access, piping, and electrical penetrations. The focus of the current research program is to study the ultimate behavior of flexible metal bellows that are used at piping penetrations. Bellows are commonly used at piping penetrations in steel containments; however, they have very few applications in concrete (reinforced or prestressed) containments. The purpose of piping bellows is to provide a soft connection between the containment shell and the pipe are attached while maintaining the containment pressure boundary. In this way, piping loads caused by differential movement between the piping and the containment shell are minimized. SNL is conducting a test program to determine the leaktight capacity of containment bellows when subjected to postulated severe accident conditions. If the test results indicate that containment bellows could be a possible failure mode of the containment pressure boundary, then methods will be developed to predict the deformation, pressure, and temperature conditions that would likely cause a bellows failure. Results from the test program would be used to validate the prediction methods. This paper provides a description of the use and design of bellows in containment piping penetrations, the types of possible bellows loadings during a severe accident, and an overview of the test program, including available test results at the time of writing

The 3D Elevation Program—Flood risk management

Science.gov (United States)

Carswell, William J.; Lukas, Vicki

2018-01-25

Flood-damage reduction in the United States has been a longstanding but elusive societal goal. The national strategy for reducing flood damage has shifted over recent decades from a focus on construction of flood-control dams and levee systems to a three-pronged strategy to (1) improve the design and operation of such structures, (2) provide more accurate and accessible flood forecasting, and (3) shift the Federal Emergency Management Agency (FEMA) National Flood Insurance Program to a more balanced, less costly flood-insurance paradigm. Expanding the availability and use of high-quality, three-dimensional (3D) elevation information derived from modern light detection and ranging (lidar) technologies to provide essential terrain data poses a singular opportunity to dramatically enhance the effectiveness of all three components of this strategy. Additionally, FEMA, the National Weather Service, and the U.S. Geological Survey (USGS) have developed tools and joint program activities to support the national strategy.The USGS 3D Elevation Program (3DEP) has the programmatic infrastructure to produce and provide essential terrain data. This infrastructure includes (1) data acquisition partnerships that leverage funding and reduce duplicative efforts, (2) contracts with experienced private mapping firms that ensure acquisition of consistent, low-cost 3D elevation data, and (3) the technical expertise, standards, and specifications required for consistent, edge-to-edge utility across multiple collection platforms and public access unfettered by individual database designs and limitations.High-quality elevation data, like that collected through 3DEP, are invaluable for assessing and documenting flood risk and communicating detailed information to both responders and planners alike. Multiple flood-mapping programs make use of USGS streamflow and 3DEP data. Flood insurance rate maps, flood documentation studies, and flood-inundation map libraries are products of these

Outcomes by Mode of Transport of ST Elevation MI Patients in the United Arab Emirates

OpenAIRE

Callachan, Edward L.; Alsheikh-Ali, Alawi A.; Nair, Satish Chandrasekhar; Bruijns, Stevan; Wallis, Lee A.

2017-01-01

Introduction The purpose of this multicenter study was to assess differences in demographics, medical history, treatment times, and follow-up status among patients with ST-elevation myocardial infarction (STEMI), who were transported to the hospital by emergency medical services (EMS) or by private vehicle, or were transferred from other medical facilities. Methods This multicenter study involved the collection of both retrospective and prospective data from 455 patients admitted to four hosp...

The Risk of Intraocular Pressure Elevation in Pediatric Non-infectious Uveitis

Science.gov (United States)

Kothari, Srishti; Foster, C. Stephen; Pistilli, Maxwell; Liesegang, Teresa L.; Daniel, Ebenezer; Sen, H. Nida; Suhler, Eric B.; Thorne, Jennifer E.; Jabs, Douglas A.; Levy-Clarke, Grace A.; Nussenblatt, Robert B.; Rosenbaum, James T.; Lawrence, Scott D.; Kempen, John H.

2015-01-01

Purpose To characterize the risk and risk factors for intraocular pressure (IOP) elevation in pediatric non-infectious uveitis. Design Multi-center retrospective cohort study. Participants Nine hundred sixteen children (1593 eyes) uveitis followed between January 1978 through December 2007 at five academic uveitis centers in United States. Methods Medical records review by trained, certified experts. Main outcome measures Prevalence and incidence of IOP≥21 and ≥30mmHg and incidence of a rise in IOP by ≥10mmHg. To avoid under ascertainment, outcomes were counted as present when IOP-lowering therapies were in use. Results Initially 251 (15.8%) and 46 eyes (2.9%) had IOP≥21 and ≥30mmHg, respectively. Factors associated with presenting IOP elevation included age 6–12 years (versus other pediatric ages), prior cataract surgery (adjusted odds ratio≥21mmHg [aOR21]=2.42, P=0.01), pars plana vitrectomy (adjusted odds ratio≥30mmHg[aOR30]=11.1, P=0.03), duration of uveitis ≥6 months (aORs30 up to 11.8, Puveitis. Statistically significant risk factors include IOP elevation or use of IOP-lowering treatment in the contralateral eye and local corticosteroid use – that demonstrated a dose-and route of administration-dependent relationship. In contrast, use of immunosuppressive drug therapy did not increase such risk. Pediatric eyes with non-infectious uveitis should be followed closely for IOP elevation when strong risk factors such as the use of local corticosteroids and contralateral IOP elevation are present. PMID:26233626

Continental extension, magmatism and elevation; formal relations and rules of thumb

Science.gov (United States)

Lachenbruch, A.H.; Morgan, P.

1990-01-01

To investigate simplified relations between elevation and the extensional, magmatic and thermal processes that influence lithosphere buoyancy, we assume that the lithosphere floats on an asthenosphere of uniform density and has no flexural strength. A simple graph relating elevation to lithosphere density and thickness provides an overview of expectable conditions around the earth and a simple test for consistancy of continental and oceanic lithosphere models. The mass-balance relations yield simple general rules for estimating elevation changes caused by various tectonic, magmatic and thermal processes without referring to detailed models. The rules are general because they depend principally on buoyancy, which under our assumptions is specified by elevation, a known quantity; they do not generally require a knowledge of lithosphere thickness and density. The elevation of an extended terrain contains important information on its tectonic and magmatic history. In the Great Basin where Cenozoic extension is estimated to be 100%, the present high mean elevation ( ~ 1.75 km) probably requires substantial low-density magmatic contributions to the extending lithosphere. The elevation cannot be reasonably explained solely as the buoyant residue of a very high initial terrane, or of a lithosphere that was initially very thick and subsequently delaminated and heated. Even models with a high initial elevation typically call for 10 km or so of accumulated magmatic material of near-crustal density. To understand the evolution of the Great Basin, it is important to determine whether such intruded material is present; some could replenish the stretching crust by underplating and crustal intrusion and some might reside in the upper mantle. The elevation maintained or approached by an intruded extending lithosphere depends on the ratio B of how fast magma is supplied from the asthenosphere ( b km/Ma) to how fast the lithosphere spreads the magma out by extension (?? Ma-1). For a

Elevated temperature and CO2 concentration effects on xylem anatomy of Scots pine

International Nuclear Information System (INIS)

Kilpelainen, A.; Gerendiain, A.Z.; Luostarinen, K.; Peltola, H.; Kellomaki, S.

2007-01-01

The effects of carbon dioxide (CO 2 ) concentrations and elevated temperatures on the xylem anatomy of 20-year old Scots pine trees were investigated. The experiment was conducted in 16 chambers containing 4 trees each with a factorial combination of both ambient and elevated CO 2 concentrations and 2 different temperature regimes. CO 2 concentrations were doubled with a corresponding increase of between 2 and 6 degrees C according to each season over a period of 6 years. The study showed that elevated CO 2 concentrations increased the ring width in 4 of the 6 analyzed treatment years. Earlywood width increased during the first 2 years of the experiment, while latewood width increased during the third year of the study. The study also showed that the tracheid walls in both the latewood and earlywood samples were thicker when either temperature levels or CO 2 levels were increased. It was noted that combined CO 2 and temperature elevations resulted in thinner tracheid walls. However, latewood tracheid lumen diameters were larger in all CO 2 and temperature treatments than trees grown in ambient conditions. It was concluded that xylem anatomy was impacted more by increases in temperature than by elevated CO 2 concentrations. 48 refs., 2 tabs., 6 figs

Feed intake and behavior of dairy goats when offered an elevated feed bunk.

Science.gov (United States)

Neave, Heather W; von Keyserlingk, Marina A G; Weary, Daniel M; Zobel, Gosia

2018-04-01

Goats are browsers and select vegetation at various heights when foraging. On commercial farms, dairy goats are typically fed from low-level feed bunks. The objective of this study was to determine how feed intake and feeding behavior vary when goats are offered feed at variable heights, with the potential of evaluating the benefits of offering an elevated feeder to dairy goats. Thirteen Saanen X dairy goats were housed in a home pen with a lying area of wood shavings, where they were pre-exposed for 24 d to 3 feeder heights designed to result in differences in head height while feeding: floor level (head lowered relative to body), head level (head level relative to body), and elevated level (head and neck angled upward). Nine groups of 3 goats each were randomly selected and housed for 24 h in a test pen identical to the home pen except that it contained 1 of each of the 3 feeder heights. Each feeder contained ad libitum chopped alfalfa silage and a top-dressed corn-based supplement, refreshed twice daily. Refusals from inside and under each feeder were weighed to calculate intake. Feed intake increased with increasing feeder height (mean ± SE; 0.18, 0.29, and 0.34 ± 0.04 kg of DM/goat for floor-level, head-level, and elevated-level feeders, respectively). Total feeding time did not vary with feeder height, but feeding rate tended to be faster at the elevated-level feeder (14.5 ± 2.1 g of DM/min) compared with head-level (9.2 ± 2.3 g of DM/min) and floor-level (8.9 ± 2.1 g of DM/min) feeders. Goats visited the floor-level feeder (36.4 ± 8.4 visits/goat) less than the head-level (79.4 ± 8.4 visits/goat) and elevated-level (74.8 ± 8.4 visits/goat) feeders. The number of displacements per minute of feeding time (physical removal of another goat from the feeding place) was greater at the elevated-level feeder (0.46 ± 0.06 displacements/min) compared with the floor-level feeder (0.23 ± 0.06 displacements/min) and tended to differ from the head-level feeder (0

Properties of Free-Machining Aluminum Alloys at Elevated Temperatures

Science.gov (United States)

Faltus, Jiří; Karlík, Miroslav; Haušild, Petr

In areas close to the cutting tool the workpieces being dry machined could be heated up to 350°C and they may be impact loaded. Therefore it is of interest to study mechanical properties of corresponding materials at elevated temperatures. Free-machining alloys of Al-Cu and Al-Mg-Si systems containing Pb, Bi and Sn additions (AA2011, AA2111B, AA6262, and AA6023) were subjected to Charpy U notch impact test at the temperatures ranging from 20 to 350°C. The tested alloys show a sharp drop in notch impact strength KU at different temperatures. This drop of KU is caused by liquid metal embrittlement due to the melting of low-melting point dispersed phases which is documented by differential scanning calorimetry. Fracture surfaces of the specimens were observed using a scanning electron microscope. At room temperature, the fractures of all studied alloys exhibited similar ductile dimple fracture micromorphology, at elevated temperatures, numerous secondary intergranular cracks were observed.

The CANDU 3 containment structure

International Nuclear Information System (INIS)

1994-01-01

The design of the CANDU 3 nuclear power plant is being developed by AECL CANDU's Saskatchewan office. There are 24 CANDU nuclear power units operating in Canada and abroad and eight units are under construction is Romania and South Korea. The design of the CANDU 3 plant has evolved on the basis of the proven CANDU design. The experiences gained during construction, commissioning and operation of the existing CANDU plants are considered in the design. Many technological enhancements have been implemented in the design processes in all areas. The object has been to develop an improved reactor design that is suitable for the current and the future markets worldwide. Throughout the design phase of CANDU 3, emphasis has been placed in reducing the cost and construction schedule of the plant. This has been achieved by implementing design improvements and using new construction techniques. Appropriate changes and improvements to the design to suit new requirements are also adopted. In CANDU plants, the containment structure acts as an ultimate barrier against the leakage of radioactive substances during normal operations and postulated accident conditions. The concept of the structural design of the containment structure has been examined in considerable detail. This has resulted in development of a new conceptual design for the containment structure for CANDU 3. This paper deals with this new design of the containment structure

Dreissenid mussels from the Great Lakes contain elevated thiaminase activity

Science.gov (United States)

Tillitt, D.E.; Riley, S.C.; Evans, A.N.; Nichols, S.J.; Zajicek, J.L.; Rinchard, J.; Richter, C.A.; Krueger, C.C.

2009-01-01

We examined thiaminase activity in dreissenid mussels collected at different depths and seasons, and from various locations in Lakes Michigan, Ontario, and Huron. Here we present evidence that two dreissenid mussel species (Dreissena bugensis and D. polymorpha) contain thiaminase activity that is 5-100 fold greater than observed in Great Lakes fishes. Thiaminase activity in zebra mussels ranged from 10,600 to 47,900??pmol g- 1??min- 1 and activities in quagga mussels ranged from 19,500 to 223,800??pmol g- 1??min- 1. Activity in the mussels was greatest in spring, less in summer, and least in fall. Additionally, we observed greater thiaminase activity in dreissenid mussels collected at shallow depths compared to mussels collected at deeper depths. Dreissenids constitute a significant and previously unknown pool of thiaminase in the Great Lakes food web compared to other known sources of this thiamine (vitamin B1)-degrading enzyme. Thiaminase in forage fish of the Great Lakes has been causally linked to thiamine deficiency in salmonines. We currently do not know whether linkages exist between thiaminase activities observed in dreissenids and the thiaminase activities in higher trophic levels of the Great Lakes food web. However, the extreme thiaminase activities observed in dreissenids from the Great Lakes may represent a serious unanticipated negative effect of these exotic species on Great Lakes ecosystems.

Adjustment of Measurements with Multiplicative Errors: Error Analysis, Estimates of the Variance of Unit Weight, and Effect on Volume Estimation from LiDAR-Type Digital Elevation Models

Directory of Open Access Journals (Sweden)

Yun Shi

2014-01-01

Full Text Available Modern observation technology has verified that measurement errors can be proportional to the true values of measurements such as GPS, VLBI baselines and LiDAR. Observational models of this type are called multiplicative error models. This paper is to extend the work of Xu and Shimada published in 2000 on multiplicative error models to analytical error analysis of quantities of practical interest and estimates of the variance of unit weight. We analytically derive the variance-covariance matrices of the three least squares (LS adjustments, the adjusted measurements and the corrections of measurements in multiplicative error models. For quality evaluation, we construct five estimators for the variance of unit weight in association of the three LS adjustment methods. Although LiDAR measurements are contaminated with multiplicative random errors, LiDAR-based digital elevation models (DEM have been constructed as if they were of additive random errors. We will simulate a model landslide, which is assumed to be surveyed with LiDAR, and investigate the effect of LiDAR-type multiplicative error measurements on DEM construction and its effect on the estimate of landslide mass volume from the constructed DEM.

Supplementary dataset for child and adult exposure and health risk evaluation following the use of metal- and metalloid-containing costume cosmetics sold in the United States

Directory of Open Access Journals (Sweden)

Angela L. Perez

2017-08-01

Full Text Available The data presented in this article are related to the research article entitled "Child and adult exposure and health risk evaluation following the use of metal- and metalloid-containing costume cosmetics sold in the United States" [1]. This article describes the concentration of metals and metalloids contained in various cosmetic products such as body paint, lipstick and eye shadow, the relative percent deviation of two analyses performed on the products and the physico-chemico properties of the metals and metalloids used in the SkinPerm model presented in the aforementioned article.

History of United States Energy. A Basic Teaching Unit on Energy. Revised.

Science.gov (United States)

McDermott, Hugh, Ed.; Scharmann, Larry, Ed.

Intended as a supplement to the units "Oil: Fuel of the Past" and "Coal: Fuel of the Past, Hope of the Future," this 3-4 day unit contains three activities which briefly explain the chronological development of energy resources and the formation and development of the Organization of Petroleum Exporting Countries (OPEC). The…

Synthesis of fluorinated poly(arylene ether)s with dibenzodioxin and spirobisindane units from new bis(pentafluorophenyl)- and bis(nonafluorobiphenyl)-containing monomers

DEFF Research Database (Denmark)

Tkachenko, Ihor M.; Belov, Nikolay A.; Kobzar, Yaroslav L.

2017-01-01

(nonafluorophenyl)-containing monomers have higher average molecular masses (Mw) in the range 47,000–88,300 and are able to form robust, solvent-cast films. Good thermal stabilities in air (up to 350 °C) were observed in all fluorinated polymers. The Brunauer–Emmett–Teller specific surface area and the pore size of polymers can...... be controlled by varying the type of the initial fluorinated monomers. It was shown that introduction of perfluorobiphenyl units is an effective tool for increasing the surface area up to 156.8 m2 g−1....

Selection of cooling fluid for an organic Rankine cycle unit recovering heat on a container ship sailing in the Arctic region

DEFF Research Database (Denmark)

Suárez de la Fuente, Santiago; Larsen, Ulrik; Pierobon, Leonardo

2017-01-01

As Arctic sea ice coverage declines it is expected that marine traffic could increase in this northern region due to shorter routes. Navigating in the Arctic offers opportunities and challenges for waste heat recovery systems (WHRS). Lower temperatures require larger heating power on board, hence...... air as coolant. This paper explores the use of two different coolants, air and seawater, for an organic Rankine cycle (ORC) unit using the available waste heat in the scavenge air system of a container ship navigating in Arctic Circle. Using a two-step single objective optimisation process, detailed...

Silicon-containing polyoxadiazoles-synthesis and perspectives.

Science.gov (United States)

Bruma, Maria; Köpnick, Thomas

2005-11-30

A review is presented on those polymers which contain diphenylsilylene units and 1,3,4-oxadiazole rings either in the main chain or in the pendent groups. The synthesis of silicon-containing monomers as well as of the polyoxadiazoles based on them is described. The properties of these polymers, such as solubility, film forming ability, thermal stability, electrochemical behavior and photoluminescence properties, and their potential applications are discussed.

Hanford Site waste management units report

International Nuclear Information System (INIS)

1993-04-01

The Hanford Site Waste Management Units Report was originated to provide information responsive to Section 3004(u) of the Hazardous and Solid Waste Amendments of the 1984. This report provides a comprehensive inventory of all types of waste management units at the Hanford Site, including a description of the units and the waste they contain. Waste management units in the report include: (1) Resource Conservation and Recovery Act of 1976 (RCRA) disposal units, (2) Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) disposal units, (3) unplanned releases, (4) inactive contaminated structures, (5) RCRA treatment, storage, and disposal (TSD) units, and (6) other storage areas. Because of the comprehensive nature of the units report, the list of units is more extensive than required by Section 3004(u) of Hazardous and Solid Waste Amendments of the 1984. In Sections 3.0 through 6.0 of this report, the four aggregate areas are subdivided into their operable units. The operable units are further divided into two parts: (1) those waste management units assigned to the operable unit that will be remediated as part of the Environmental Restoration Remedial Actions (ERRA) Program, and (2) those waste management units located within the operable unit boundaries but not assigned to the ERRA program. Only some operable unit sections contain the second part

Increased serum levels of hyaluronic acid in pregnancies complicated by preeclampsia or hemolysis, elevated liver enzymes, and low platelets syndrome.

Science.gov (United States)

Osmers, R G; Schütz, E; Diedrich, F; Wehry, B; Krauss, T; Oellerich, M; Kuhn, W

1998-02-01

Fifteen percent of patients who later have hemolysis, elevated liver enzymes, and low platelets syndrome develop initially have nonspecific symptoms. Early diagnosis could ensure adequate obstetric management; however, prognostic biochemical tests are lacking. We hypothesized that elevated hyaluronic acid serum levels might be an early indicator of hemolysis, elevated liver enzymes, and low platelets syndrome because it is known to be a sensitive marker of liver cell function. Hyaluronic acid in serum was measured in patients with normal pregnancies (n = 109) and in those patients with pregnancies complicated by preeclampsia (n = 14) or hemolysis, elevated liver enzymes, and low platelets syndrome (n = 11). A significant increase in hyaluronic acid serum concentrations was observed in patients with hemolysis, elevated liver enzymes, and low platelets syndrome or with preeclampsia (p hyaluronic acid serum levels in hemolysis, elevated liver enzymes, and low platelets syndrome correlated with the clinical severity of the individual course of disease as measured by intensive care unit time (r = 0.72; p hyaluronic acid in preeclampsia and hemolysis, elevated liver enzymes, and low platelets syndrome are significantly elevated and might play an important diagnostic and prognostic role in patients with hemolysis, elevated liver enzymes, and low platelets syndrome.

Predictive value of elevated D-dimer in patients undergoing primary angioplasty for ST elevation myocardial infarction.

Science.gov (United States)

Akgul, Ozgur; Uyarel, Huseyin; Pusuroglu, Hamdi; Gul, Mehmet; Isiksacan, Nilgun; Turen, Selahattin; Erturk, Mehmet; Surgit, Ozgur; Cetin, Mustafa; Bulut, Umit; Baycan, Omer F; Uslu, Nevzat

2013-10-01

The aim of this study was to evaluate the prognostic value of D-dimer in patients with STEMI undergoing primary percutaneous coronary intervention (PCI). The prognostic value of D-dimer has been documented in patients with acute coronary syndrome without ST-segment elevation. However, its value in acute ST-segment elevation myocardial infarction (STEMI) remains unclear. We prospectively enrolled 453 consecutive STEMI patients (mean age 55.6 ± 12.4 years, 364 male, 89 female) undergoing primary PCI. The study population was divided into tertiles based on admission D-dimer values. The high D-dimer group (n = 151) was defined as a value in the third tertile [>0.72 ug/ml fibrinogen equivalent units (FEU)], and the low D-dimer group (n = 302) included those patients with a value in the lower two tertiles (≤0.72 ug/ml FEU). Clinical characteristics, in-hospital and 6-month outcomes of primary PCI were analyzed. The patients of the high D-dimer group were older (mean age 60.1 ± 13.5 versus 52.4 ± 10.6, P 0.72 ug/ml FEU) was found to be a powerful independent predictor of 6-month all-cause mortality (odds ratio: 10.1, 95% confidence interval: 1.24-42.73, P = 0.03). These results suggest that a high admission D-dimer, level was associated with increased in-hospital cardiovascular mortality and 6-month all-cause mortality in patients with STEMI undergoing primary PCI.

Authenticated Secure Container System (ASCS)

International Nuclear Information System (INIS)

1991-01-01

Sandia National Laboratories developed an Authenticated Secure Container System (ASCS) for the International Atomic Energy Agency (IAEA). Agency standard weights and safeguards samples can be stored in the ASCS to provide continuity of knowledge. The ASCS consists of an optically clear cover, a base containing the Authenticated Item Monitoring System (AIMS) transmitter, and the AIMS receiver unit for data collection. The ASCS will provide the Inspector with information concerning the status of the system, during a surveillance period, such as state of health, tampering attempts, and movement of the container system. The secure container is located inside a Glove Box with the receiver located remotely from the Glove Box. AIMS technology uses rf transmission from the secure container to the receiver to provide a record of state of health and tampering. The data is stored in the receiver for analysis by the Inspector during a future inspection visit. 2 refs

A conceptual prototype for the next-generation national elevation dataset

Science.gov (United States)

Stoker, Jason M.; Heidemann, Hans Karl; Evans, Gayla A.; Greenlee, Susan K.

2013-01-01

In 2012 the U.S. Geological Survey's (USGS) National Geospatial Program (NGP) funded a study to develop a conceptual prototype for a new National Elevation Dataset (NED) design with expanded capabilities to generate and deliver a suite of bare earth and above ground feature information over the United States. This report details the research on identifying operational requirements based on prior research, evaluation of what is needed for the USGS to meet these requirements, and development of a possible conceptual framework that could potentially deliver the kinds of information that are needed to support NGP's partners and constituents. This report provides an initial proof-of-concept demonstration using an existing dataset, and recommendations for the future, to inform NGP's ongoing and future elevation program planning and management decisions. The demonstration shows that this type of functional process can robustly create derivatives from lidar point cloud data; however, more research needs to be done to see how well it extends to multiple datasets.

Status report for the 3D Elevation Program, 2013-2014

Science.gov (United States)

Lukas, Vicki; Eldridge, Diane F.; Jason, Allyson L.; Saghy, David L.; Steigerwald, Pamela R.; Stoker, Jason M.; Sugarbaker, Larry J.; Thunen, Diana R.

2015-09-25

The 3D Elevation Program (3DEP) goal is to acquire, manage, and distribute enhanced three-dimensional elevation data for the Nation and U.S. territories by 2023. This status report covers implementation activities during 2013–2014 to include meeting funding objectives, developing a management structure, modernizing systems, and collecting and producing initial 3DEP data and products. The Nation will not have complete coverage of 3DEP quality data until 2023 assuming that sufficient funding is available. In spite of the overall condition of government budgets, the 3DEP initiative has gained widespread support and had incremental budget success to include supplemental funding resulting from natural disasters. The 3DEP Executive Forum and a wide range of professional organizations are actively working to maintain support for the program. The systems that have been developed to support increasing acquisition and processing levels are largely in place. The first 3DEP quality datasets were released to the public in late 2014. In addition, light detection and ranging (lidar), interferometric synthetic aperture radar (ifsar), and digital elevation models (DEMs) acquired before 2014 are all supported within the new infrastructure and available for download. Research is ongoing to expand the suite of products and services, and to increase overall throughput and data management efficiency. Emerging technologies may result in lower acquisition costs in the future. Elevation data acquired by 3DEP partnerships will be available through The National Map representing one of the largest and most comprehensive databases publicly available for the United States. 

Containment heat removal system

International Nuclear Information System (INIS)

Wade, G.E.; Barbanti, G.; Gou, P.F.; Rao, A.S.; Hsu, L.C.

1992-01-01

This patent describes a nuclear system of a type including a containment having a nuclear reactor therein, the nuclear reactor including a pressure vessel and a core in the pressure vessel, the system. It comprises a gravity pool of coolant disposed at an elevation sufficient to permit a flow of coolant into the nuclear reactor pressure vessel against a predetermined pressure within the nuclear reactor pressure vessel; means for reducing a pressure of steam in the nuclear reactor pressure vessel to a value less than the predetermined pressure in the event of a nuclear accident, the means including a depressurization valve connected to the pressure vessel, the means further including steam heat dissipating means such dissipating means including a suppression pool; a supply of water in the suppression pool, there being a headspace in the suppression pool above the water supply; a substantial amount of air in the head space; means for feeding pressurized steam from the nuclear reactor pressure vessel to a location under a surface of the supply of water, the supply of water being effective to absorb heat sufficient to reduce steam pressure below the predetermined pressure; and a check valve for communicating the headspace with the containment, the check valve being oriented to vent air in the headspace to the containment when a pressure in the headspace exceeds a pressure in the containment by a predetermined pressure differential

Complex behavior of elevators in peak traffic

Science.gov (United States)

Nagatani, Takashi

2003-08-01

We study the dynamical behavior of elevators in the morning peak traffic. We present a stochastic model of the elevators to take into account the interactions between elevators through passengers. The dynamics of the elevators is expressed in terms of a coupled nonlinear map with noises. The number of passengers carried by an elevator and the time-headway between elevators exhibit the complex behavior with varying elevator trips. It is found that the behavior of elevators exhibits a deterministic chaos even if there are no noises. The chaotic motion depends on the loading parameter, the maximum capacity of an elevator, and the number of elevators. When the loading parameter is superior to the threshold, each elevator carries a full load of passengers throughout its trip. The dependence of the threshold (transition point) on the elevator capacity is clarified.

Elevated carbon dioxide and ozone alter productivity and ecosystem carbon content in northern temperate forests

Science.gov (United States)

Alan F. Talhelm; Kurt S. Pregitzer; Mark E. Kubiske; Donald R. Zak; Courtney E. Campany; Andrew J. Burton; Richard E. Dickson; George R. Hendrey; J. G. Isebrands; Keith F. Lewin; John Nagy; David F. Karnosky

2014-01-01

Three young northern temperate forest communities in the north-central United States were exposed to factorial combinations of elevated carbon dioxide (CO2) and tropospheric ozone (O3) for 11 years. Here, we report results from an extensive sampling of plant biomass and soil conducted at the conclusion of the experiment...

Iowa Bedrock Surface Elevation

Data.gov (United States)

Iowa State University GIS Support and Research Facility — This Digital Elevation Model (DEM) of the bedrock surface elevation in Iowa was compiled using all available data, principally information from GEOSAM, supplemented...

77 FR 20846 - Certain Food Containers, Cups, Plates, Cutlery, and Related Items and Packaging Thereof...

Science.gov (United States)

2012-04-06

... INTERNATIONAL TRADE COMMISSION [Inv. No. 337-TA-835] Certain Food Containers, Cups, Plates... the sale within the United States after importation of certain food containers, cups, plates, cutlery... importation, or the sale within the United States after importation of certain food containers, cups, plates...

The space station tethered elevator system

Science.gov (United States)

Anderson, Loren A.

1989-01-01

The optimized conceptual engineering design of a space station tethered elevator is presented. The elevator is an unmanned mobile structure which operates on a ten kilometer tether spanning the distance between the Space Station and a tethered platform. Elevator capabilities include providing access to residual gravity levels, remote servicing, and transportation to any point along a tether. The potential uses, parameters, and evolution of the spacecraft design are discussed. Engineering development of the tethered elevator is the result of work conducted in the following areas: structural configurations; robotics, drive mechanisms; and power generation and transmission systems. The structural configuration of the elevator is presented. The structure supports, houses, and protects all systems on board the elevator. The implementation of robotics on board the elevator is discussed. Elevator robotics allow for the deployment, retrieval, and manipulation of tethered objects. Robotic manipulators also aid in hooking the elevator on a tether. Critical to the operation of the tethered elevator is the design of its drive mechanisms, which are discussed. Two drivers, located internal to the elevator, propel the vehicle along a tether. These modular components consist of endless toothed belts, shunt-wound motors, regenerative power braking, and computer controlled linear actuators. The designs of self-sufficient power generation and transmission systems are reviewed. Thorough research indicates all components of the elevator will operate under power provided by fuel cells. The fuel cell systems will power the vehicle at seven kilowatts continuously and twelve kilowatts maximally. A set of secondary fuel cells provides redundancy in the unlikely event of a primary system failure. Power storage exists in the form of Nickel-Hydrogen batteries capable of powering the elevator under maximum loads.

Appending High-Resolution Elevation Data to GPS Speed Traces for Vehicle Energy Modeling and Simulation

Energy Technology Data Exchange (ETDEWEB)

Wood, E.; Burton, E.; Duran, A.; Gonder, J.

2014-06-01

Accurate and reliable global positioning system (GPS)-based vehicle use data are highly valuable for many transportation, analysis, and automotive considerations. Model-based design, real-world fuel economy analysis, and the growing field of autonomous and connected technologies (including predictive powertrain control and self-driving cars) all have a vested interest in high-fidelity estimation of powertrain loads and vehicle usage profiles. Unfortunately, road grade can be a difficult property to extract from GPS data with consistency. In this report, we present a methodology for appending high-resolution elevation data to GPS speed traces via a static digital elevation model. Anomalous data points in the digital elevation model are addressed during a filtration/smoothing routine, resulting in an elevation profile that can be used to calculate road grade. This process is evaluated against a large, commercially available height/slope dataset from the Navteq/Nokia/HERE Advanced Driver Assistance Systems product. Results will show good agreement with the Advanced Driver Assistance Systems data in the ability to estimate road grade between any two consecutive points in the contiguous United States.

The 3D Elevation Program initiative: a call for action

Science.gov (United States)

Sugarbaker, Larry J.; Constance, Eric W.; Heidemann, Hans Karl; Jason, Allyson L.; Lukas, Vicki; Saghy, David L.; Stoker, Jason M.

2014-01-01

The 3D Elevation Program (3DEP) initiative is accelerating the rate of three-dimensional (3D) elevation data collection in response to a call for action to address a wide range of urgent needs nationwide. It began in 2012 with the recommendation to collect (1) high-quality light detection and ranging (lidar) data for the conterminous United States (CONUS), Hawaii, and the U.S. territories and (2) interferometric synthetic aperture radar (ifsar) data for Alaska. Specifications were created for collecting 3D elevation data, and the data management and delivery systems are being modernized. The National Elevation Dataset (NED) will be completely refreshed with new elevation data products and services. The call for action requires broad support from a large partnership community committed to the achievement of national 3D elevation data coverage. The initiative is being led by the U.S. Geological Survey (USGS) and includes many partners—Federal agencies and State, Tribal, and local governments—who will work together to build on existing programs to complete the national collection of 3D elevation data in 8 years. Private sector firms, under contract to the Government, will continue to collect the data and provide essential technology solutions for the Government to manage and deliver these data and services. The 3DEP governance structure includes (1) an executive forum established in May 2013 to have oversight functions and (2) a multiagency coordinating committee based upon the committee structure already in place under the National Digital Elevation Program (NDEP). The 3DEP initiative is based on the results of the National Enhanced Elevation Assessment (NEEA) that was funded by NDEP agencies and completed in 2011. The study, led by the USGS, identified more than 600 requirements for enhanced (3D) elevation data to address mission-critical information requirements of 34 Federal agencies, all 50 States, and a sample of private sector companies and Tribal and local

Acinetobacter baumannii K11 and K83 capsular polysaccharides have the same 6-deoxy-l-talose-containing pentasaccharide K units but different linkages between the K units.

Science.gov (United States)

Kenyon, Johanna J; Shashkov, Alexander S; Senchenkova, Sof'ya N; Shneider, Mikhail M; Liu, Bin; Popova, Anastasiya V; Arbatsky, Nikolay P; Miroshnikov, Konstantin A; Wang, Lei; Knirel, Yuriy A; Hall, Ruth M

2017-10-01

Acinetobacter baumannii produces a variety of capsular polysaccharides (CPS) via genes located at the chromosomal K locus and some KL gene clusters include genes for the synthesis of specific sugars. The structures of K11 and K83 CPS produced by isolates LUH5545 and LUH5538, which carry related KL11a and KL83 gene clusters, respectively, were established by sugar analysis and one- and two-dimensional 1 H and 13 C NMR spectroscopy. Both CPS contain l-rhamnose (l-Rha) and 6-deoxy-l-talose (l-6dTal), and both KL gene clusters include genes for dTDP-l-Rhap synthesis and a tle (talose epimerase) gene encoding an epimerase that converts dTDP-l-Rhap to dTDP-l-6dTalp. The K11 and K83 repeat units are the same pentasaccharide, consisting of d-glucose, l-Rha, l-6dTal, and N-acetyl-d-glucosamine, except that l-6dTal is 2-O-acetylated in K83. However, the K units are linked differently, with l-Rha in the main chain in K11, but as a side-branch in K83. KL11 and KL83 encode unrelated Wzy polymerases that link the K units together and different acetyltransferases, though only Atr8 from KL83 is active. The substrate specificity of each Wzy polymerase was assigned, and the functions of all glycosyltransferases were predicted. The CPS structures produced by three closely related K loci, KL29, KL105 and KL106, were also predicted. Copyright © 2017 Elsevier B.V. All rights reserved.

Insights into the behavior of LWR steel containment buildings during severe accidents

International Nuclear Information System (INIS)

Clauss, D.B.; Horschel, D.S.; Blejwas, T.E.

1987-01-01

Investigations into the performance of steel containment subject to pressure and temperature greater than their design basis loads are discussed. The timing, mechanism, and location of a containment failure, i.e., release of radioactive materials, have an important impact on the consequences of a severe accident. We review the results of experiments on steel containment models pressurized to failure, on aged and unaged seals subjected to elevated temperature and pressure, and on electrical penetration assemblies tested for leakage. Based on the results, the important features and details of analytical methods that can be used to predict containment performance are identified. Finally, we speculate on the performance of steel containments in severe accident conditions. (orig.)

Context-Aware Elevator Scheduling

OpenAIRE

Strang, Thomas; Bauer, Christian

2007-01-01

Research on context-aware systems is usually user-centric and thus focussed on the context of a specific user to serve his or her needs in an optimized way. In this paper, we want to apply core concepts developed in research on context-awareness in a system-centric way, namely to elevator systems. We show with three different examples that the performance of an elevator system can be significantly improved if the elevator control has access to contextual knowledge. The first example demons...

Nuclear reactor container

International Nuclear Information System (INIS)

Fukui, Tooru; Murase, Michio; Kataoka, Yoshiyuki; Hidaka, Masataka; Sumita, Isao; Tominaga, Kenji.

1992-01-01

In a nuclear reactor container, a chamber in communication with a wet well of a pressure suppression chamber is disposed and situated to such a position that the temperature is lower than a chamber containing pool water upon occurrence of loss of coolant accident. In addition, the inner surface of the pressure suppression chamber is constituted with steel walls in contact with pool water, and an outer circumferential pool is disposed at the outer circumferential surface thereof. Further, a circulation channel is disposed, and a water intake port is disposed at a position higher than an exit to the pool water, and a water discharge port is opened in the pool water at a position lower than the exit to the pool water. With such a constitution, the allowable temperature of the pressure suppression pool water can be elevated to a saturated steam temperature corresponding to the resistant pressure of the container, so that the temperature difference between the pressure suppression pool and the outer side thereof is increased by so much, to improve thermal radiation performance. Accordingly, it can be utilized as a pressure suppression means for a plant of greater power. Further, thermal conduction efficiency from the pool water region of the pressure suppression chamber to the outer circumferential pool water is improved, or thermal radiation area is enlarged due to the circulation channel, to improve the heat radiation performance. (N.H.)

Elevated temperature and CO{sub 2} concentration effects on xylem anatomy of Scots pine

Energy Technology Data Exchange (ETDEWEB)

Kilpelainen, A.; Gerendiain, A.Z.; Luostarinen, K.; Peltola, H.; Kellomaki, S. [Joensuu Univ., Joensuu (Finland). Faculty of Forestry

2007-09-15

The effects of carbon dioxide (CO{sub 2}) concentrations and elevated temperatures on the xylem anatomy of 20-year old Scots pine trees were investigated. The experiment was conducted in 16 chambers containing 4 trees each with a factorial combination of both ambient and elevated CO{sub 2} concentrations and 2 different temperature regimes. CO{sub 2} concentrations were doubled with a corresponding increase of between 2 and 6 degrees C according to each season over a period of 6 years. The study showed that elevated CO{sub 2} concentrations increased the ring width in 4 of the 6 analyzed treatment years. Earlywood width increased during the first 2 years of the experiment, while latewood width increased during the third year of the study. The study also showed that the tracheid walls in both the latewood and earlywood samples were thicker when either temperature levels or CO{sub 2} levels were increased. It was noted that combined CO{sub 2} and temperature elevations resulted in thinner tracheid walls. However, latewood tracheid lumen diameters were larger in all CO{sub 2} and temperature treatments than trees grown in ambient conditions. It was concluded that xylem anatomy was impacted more by increases in temperature than by elevated CO{sub 2} concentrations. 48 refs., 2 tabs., 6 figs.

Performance Evaluation and Modelling of Container Terminals

Science.gov (United States)

Venkatasubbaiah, K.; Rao, K. Narayana; Rao, M. Malleswara; Challa, Suresh

2018-02-01

The present paper evaluates and analyzes the performance of 28 container terminals of south East Asia through data envelopment analysis (DEA), principal component analysis (PCA) and hybrid method of DEA-PCA. DEA technique is utilized to identify efficient decision making unit (DMU)s and to rank DMUs in a peer appraisal mode. PCA is a multivariate statistical method to evaluate the performance of container terminals. In hybrid method, DEA is integrated with PCA to arrive the ranking of container terminals. Based on the composite ranking, performance modelling and optimization of container terminals is carried out through response surface methodology (RSM).

Microstructure and elevated-temperature erosion-oxidation behaviour of aluminized 9Cr-1Mo Steel

Science.gov (United States)

Huttunen-Saarivirta, E.; Honkanen, M.; Tsipas, S. A.; Omar, H.; Tsipas, D.

2012-10-01

Degradation of materials by a combination of erosive wear and atmospheric oxidation at elevated temperatures constitutes a problem in some power generation processes, such as fluidized-bed combustion. In this work, 9Cr-1Mo steel, a common tube material in combustion chambers, is coated by a pack cementation method from an Al-containing pack in order to improve the resistance to erosion-oxidation at elevated temperatures. The resulting coating is studied in terms of microstructure and microhardness and tested for its resistance against impacts by sand particles in air at temperatures of 550-700 °C under several conditions, with thickness changes and appearance of the exposed surfaces being studied. The coating was found to contain several phases and layers, the outermost of which was essentially Al-rich and contained e.g., small AlN precipitates. The microhardness values for such coating ranged from 950 to 1100 HV20g. The coating provided the substrate with increased protection particularly against normal particle impacts, as manifested by smaller thickness losses for coated specimens as compared to uncoated counterparts. However, much of the coating was lost under all test conditions, despite the fact that particle debris formed a homogeneous layer on the surface. These results are described and discussed in this paper.

Containment loading during severe core damage accidents

International Nuclear Information System (INIS)

Fermandjian, J.; Evrard, J.M.; Cenerino, C.; Berthion, Y.; Carvallo, G.

1984-11-01

The objective of the article is to study the influence of the state of the reactor cavity (dry or flooded) and of the corium coolability on the thermal-hydraulics in the containment in the case of an accident sequence involving core melting and subsequent containment basemat erosion, in a 900 MWe PWR unit. Calculations are performed by using the JERICHO thermal hydraulics code

The Association Between Urine Output, Creatinine Elevation, and Death.

Science.gov (United States)

Engoren, Milo; Maile, Michael D; Heung, Michael; Jewell, Elizabeth S; Vahabzadeh, Christie; Haft, Jonathan W; Kheterpal, Sachin

2017-04-01

Acute kidney injury can be defined by a fall in urine output, and urine output criteria may be more sensitive in identifying acute kidney injury than traditional serum creatinine criteria. However, as pointed out in the Kidney Disease Improving Global Outcome guidelines, the association of urine output with subsequent creatinine elevations and death is poorly characterized. The purpose of this study was to determine what degrees of reduced urine output are associated with subsequent creatinine elevation and death. This was a retrospective cohort study of adult patients (age ≥18 years) cared for in a cardiovascular intensive care unit after undergoing cardiac operations in a tertiary care university medical center. All adult patients who underwent cardiac operations and were not receiving dialysis preoperatively were studied. The development of acute kidney injury was defined as an increase in creatinine of more than 0.3 mg/dL or by more than 50% above baseline by postoperative day 3. Acute kidney injury developed in 1,061 of 4,195 patients (25%). Urine output had moderate discrimination in predicting subsequent acute kidney injury (C statistic = .637 ± .054). Lower urine output and longer duration of low urine output were associated with greater odds of developing acute kidney injury and death. We found that there is similar accuracy in using urine output corrected for actual, ideal, or adjusted weight to discriminate future acute kidney injury by creatinine elevation and recommend using actual weight for its simplicity. We also found that low urine output is associated with subsequent acute kidney injury and that the association is greater for lower urine output and for low urine output of longer durations. Low urine output (creatinine elevation, is independently associated with mortality. Copyright © 2017 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Elevated prostacyclin biosynthesis in mice impacts memory and anxiety-like behavior.

Science.gov (United States)

Vollert, Craig; Ohia, Odochi; Akasaka, Hironari; Berridge, Casey; Ruan, Ke-He; Eriksen, Jason L

2014-01-01

Prostacyclin is an endogenous lipid metabolite with properties of vasodilation and anti-platelet aggregation. While the effects of prostacyclin on the vascular protection have been well-documented, the role of this eicosanoid in the central nervous system has not been extensively studied. Recently, a transgenic mouse containing a hybrid enzyme, of cyclooxygenase-1 linked to prostacyclin synthase, was developed that produces elevated levels of prostacyclin in vivo. The goal of this study was to investigate whether increased prostacyclin biosynthesis could affect behavioral phenotypes in mice. Our results uncovered that elevated levels of prostacyclin broadly affect both cognitive and non-cognitive behaviors, including decreased anxiety-like behavior and improved learning in the fear-conditioning memory test. This study demonstrates that prostacyclin plays an important, but previously unrecognized, role in central nervous system function and behavior. Copyright © 2013 Elsevier B.V. All rights reserved.

19 CFR 10.540 - Packing materials and containers for shipment.

Science.gov (United States)

2010-04-01

...-Singapore Free Trade Agreement Rules of Origin § 10.540 Packing materials and containers for shipment. (a... the United States. Accordingly, in applying either the build-down or build-up method for determining... shipping container which it purchased from Company B in Singapore. The shipping container is originating...

Water injection device for reactor container

International Nuclear Information System (INIS)

Sakaki, Isao.

1996-01-01

A pressure vessel incorporating a reactor core is placed and secured on a pedestal in a dry well of a reactor container. A pedestal water injection line is disposed opened at one end in a pedestal cavity passing through the side wall of the pedestal and led at the other end to the outside of the reactor container. A substitution dry well spray line is connected to a spray header disposed at the upper portion of the dry well. When the pressure vessel should be damaged by a molten reactor core and the molten reactor core should drop to the dry well upon occurrence of an accident, the molten reactor core on the floor of the pedestal is cooled by water injection from the pedestal water injection line. At the same time, the elevation of the pressure and the temperature in the reactor container is suppressed by the water injection of the substitution dry well spray line. This can avoid large scaled release of radioactive materials to the environmental circumference. (I.N.)

Space Station tethered elevator system

Science.gov (United States)

Haddock, Michael H.; Anderson, Loren A.; Hosterman, K.; Decresie, E.; Miranda, P.; Hamilton, R.

1989-01-01

The optimized conceptual engineering design of a space station tethered elevator is presented. The tethered elevator is an unmanned, mobile structure which operates on a ten-kilometer tether spanning the distance between Space Station Freedom and a platform. Its capabilities include providing access to residual gravity levels, remote servicing, and transportation to any point along a tether. The report discusses the potential uses, parameters, and evolution of the spacecraft design. Emphasis is placed on the elevator's structural configuration and three major subsystem designs. First, the design of elevator robotics used to aid in elevator operations and tethered experimentation is presented. Second, the design of drive mechanisms used to propel the vehicle is discussed. Third, the design of an onboard self-sufficient power generation and transmission system is addressed.

Mobile emergency response unit

International Nuclear Information System (INIS)

Kadi, W.J.; Trolan, R.T.; Becker, J.F.

1979-01-01

The Hotspot quick-response unit was the solution to a requirement to find, identify, and control areas of radioactive contamination at the scene of a nuclear weapons accident. The unit consists of two trucks and two trailers, and is designed to be transported by one U.S. Air Force C-141. One truck (generator truck) carries a 40 kW generator-heater-air conditioner combination, spare tires, and accessories. The other (water truck) carries supplies and a 250-gal water tank. One trailer (counting trailer) contains detecting, counting, and recording equipment. The other (decontaminating trailer) contains a shower, sink, 30-gal hot water tank, and supplies

Elevator deflections on the icing process

Science.gov (United States)

Britton, Randall K.

1990-01-01

The effect of elevator deflection of the horizontal stabilizer for certain icing parameters is investigated. Elevator deflection can severely change the lower and upper leading-edge impingement limits, and ice can accrete on the elevator itself. Also, elevator deflection had practically no effect on the maximum local collection efficiency. It is shown that for severe icing conditions (large water droplets), elevator deflections that increase the projected height of the airfoil can significantly increase the total collection efficiency of the airfoil.

46 CFR 183.540 - Elevators.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Elevators. 183.540 Section 183.540 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) ELECTRICAL INSTALLATION Miscellaneous Systems and Requirements § 183.540 Elevators. Each elevator on a vessel must meet the requirements of ANSI A 17.1 ...

Chest pain, troponin rise, and ST-elevation in an adolescent boy following the use of the synthetic cannabis product K2.

Science.gov (United States)

Zaleta, Sona; Kumar, Prashant; Miller, Sarah

2016-01-01

"Legal highs" such as K2, which typically contain synthetic cannabinoids, are increasingly popular with adolescents around the world. We have limited knowledge concerning their toxicity or adverse effects and their mechanism of action is poorly understood. While synthetic cannabinoids have been linked to adverse cardiovascular effects, cases of ST-elevation myocardial infarction (STEMI) associated with K2 use are exceedingly rare. We report a case of a 14-year-old boy who suffered an STEMI after smoking K2. To our knowledge, this is not only the youngest case of an STEMI associated with K2 use, but also the first case to be reported outside of the United States of America. Pediatricians worldwide must be aware of the clinical significance and potential harm associated with the use of synthetic cannabinoids, to better educate patients and their families regarding the dangers of using such "legal" substances.

Properties, sustainability and elevated temperature behavior of concrete containing Portland limestone cement

Science.gov (United States)

El-Hawary, Moetaz; Ahmed, Mahmoud

2017-09-01

The utilization of some type of cheap filler as partial cement replacement is an effective way of improving concrete sustainability. With the recent trends to reduce water to cement ratio and improve compaction, there is no enough space or water for complete hydration of cement. This means that actually, a portion of mixed cement acts as expensive filler. Replacing this portion with cheaper filler that requires less energy to produce is, therefore, beneficial. Crushed limestone is the most promising filler. This work is to investigate the effect of the amount of limestone fillers on the sustainability and the fresh and mechanical properties of the resulting concrete. A rich mix is designed with a low water/cement ratio of 0.4. Lime is introduced as a replacement percentage of cement. Ratios of 0, 10, 20 and 30% were used. Slump, compressive strength, specific gravity and water absorption are evaluated for every mix. In addition, the effect of the amount of lime on the residual strength of concrete subjected to elevated temperatures is also investigated. Samples are subjected to six different temperature stations of 20, 100, 200, 300, 500 and 700°C for six hours before being cooled and subsequently tested for compressive strength and specific gravity. Sustainability of the tested mixes is evaluated through reductions in the emitted carbon dioxide, energy and reduction in cost. Based on the annual use of concrete in Kuwait, the sustainability benefits resulting from the use of limestone filler in Kuwait are evaluated and assessed. The paper is concluded with the recommendation of the use of 15% limestone filler as partial cement replacement where the properties and the behavior under high temperature of the resulting concrete are almost the same as those of conventional concrete with considerable cost and sustainability benefits.

Method of making Tl-Sr-Ca-Cu-oxide superconductors comprising heating at elevated pressures in a sealed container

International Nuclear Information System (INIS)

Lechtev, W.L.; Osofsky, M.S.; Skelton, E.F.; Toth, L.E.

1992-01-01

This patent describes a method of forming a Tl-Sr-Ca-Cu-oxide high T c superconductor. It comprises forming a reaction mixture of the oxides of Sr, Cu, Ca, and Tl in stoichiometric proportions to make a Tl-Sr-Ca-Cu-oxide high T c superconducting compound; compressing the reaction mixture into a hard body; placing the hard body into a container for containing thallium vapor; evacuating and sealing the hard body in the container; heating the hard body and the container at a temperature of about 800 degrees C to about 950 degrees C and under pressure of at least about 30,000 psi until the container metal around the hard body and the oxides of Tl, Sr, Ca, and Cu react to form a superconducting compound; and cooling the superconducting compound to room temperature and returning the superconducting compound to atmospheric pressure

Application of an automated patrol-type monitoring system in the reinforced concrete containment vessel at Kashiwazaki-Kariwa Nuclear Power Plant Units 6 and 7

International Nuclear Information System (INIS)

Kimoto, T.; Senoh, M.; Hirakawa, H.; Tanaka, K.; Takahashi, M.

1996-01-01

An automated patrol-type monitoring system was applied to the first Advanced Boiling Water Reactor (ABWR) plants in the world, Kashiwazaki-Kariwa Nuclear Power Plant Units 6 and 7. The system consists of two robots traveling along monorail and several ITV systems. This monitoring system is used to watch the operating incident of key components of ABWR, such as water leakage from packing in Fine Motion Control Rod Drive (FM-CRD), Reactor Internal Pump (RIP) etc. which are located in the reinforced concrete containment and usually could not be accessible under operation. The traveling robots are equipped with the three kinds of sensors, an infrared camera, a color TV camera and a microphone, and have a capability to inspect the pre-determined inspection points guided by the monorail. This monitoring system is automatically turned on to start inspection at a scheduled time. For Units 6 and 7, this monitoring system, two robots and several ITV systems, can be controlled from one common control desk and one handy-type remote control panel. Since this monitoring system was installed at Kashiwazaki-Kariwa Nuclear Power Plant Units 6 and 7, this system has been operating successfully. (The installation and testing of the system for Unit 6 was finished completely and the testing the system for Unit 7 has been carrying out.) (author)

Sensitivity analysis of land unit suitability for conservation using a knowledge-based system.

Science.gov (United States)

Humphries, Hope C; Bourgeron, Patrick S; Reynolds, Keith M

2010-08-01

The availability of spatially continuous data layers can have a strong impact on selection of land units for conservation purposes. The suitability of ecological conditions for sustaining the targets of conservation is an important consideration in evaluating candidate conservation sites. We constructed two fuzzy logic-based knowledge bases to determine the conservation suitability of land units in the interior Columbia River basin using NetWeaver software in the Ecosystem Management Decision Support application framework. Our objective was to assess the sensitivity of suitability ratings, derived from evaluating the knowledge bases, to fuzzy logic function parameters and to the removal of data layers (land use condition, road density, disturbance regime change index, vegetation change index, land unit size, cover type size, and cover type change index). The amount and geographic distribution of suitable land polygons was most strongly altered by the removal of land use condition, road density, and land polygon size. Removal of land use condition changed suitability primarily on private or intensively-used public land. Removal of either road density or land polygon size most strongly affected suitability on higher-elevation US Forest Service land containing small-area biophysical environments. Data layers with the greatest influence differed in rank between the two knowledge bases. Our results reinforce the importance of including both biophysical and socio-economic attributes to determine the suitability of land units for conservation. The sensitivity tests provided information about knowledge base structuring and parameterization as well as prioritization for future data needs.

Building a secondary containment system

Energy Technology Data Exchange (ETDEWEB)

Broder, M.F.

1994-10-01

Retail fertilizer and pesticide dealers across the United States are installing secondary containment at their facilities or are seriously considering it. Much of this work is in response to new state regulations; however, many dealers not facing new regulations are upgrading their facilities to reduce their liability, lower their insurance costs, or comply with anticipated regulations. The Tennessee Valley Authority`s (TVA) National Fertilizer and Environmental Research Center (NFERC) has assisted dealers in 22 states in retrofitting containment to their facilities. Simultaneous improvements in the operational efficiency of the facilities have been achieved at many of the sites. This paper is based on experience gained in that work and details the rationale used in planning secondary containment and facility modifications.

Residual characteristic properties of ternary blended steel fibre reinforced concrete subjected to sustained elevated temperature

Directory of Open Access Journals (Sweden)

Sinha Deepa A.

2013-09-01

Full Text Available To study the behavior of ternary blended steel fibre reinforced concrete when subjected to 800 Deg.C and 1000 Deg.C for 3 hours. It has been found that the ternary blended steel fibre reinforced concrete containing (FA+GGBFS and (FA+MK offer higher resistance to sustained elevated temperatures upto 800 Deg.C, where as the blend containing (FA+SF does not offer any resistance at this temperature. The study reveals that the blend containing (FA+GGBFS and (FA+MK gives highest resistance at replacement levels of (10+20 and (15+15 respectively at sustained exposure to 800 Deg.C.

Changes in Respiratory Mitochondrial Machinery and Cytochrome and Alternative Pathway Activities in Response to Energy Demand Underlie the Acclimation of Respiration to Elevated CO2 in the Invasive Opuntia ficus-indica1[OA

Science.gov (United States)

Gomez-Casanovas, Nuria; Blanc-Betes, Elena; Gonzalez-Meler, Miquel A.; Azcon-Bieto, Joaquim

2007-01-01

Studies on long-term effects of plants grown at elevated CO2 are scarce and mechanisms of such responses are largely unknown. To gain mechanistic understanding on respiratory acclimation to elevated CO2, the Crassulacean acid metabolism Mediterranean invasive Opuntia ficus-indica Miller was grown at various CO2 concentrations. Respiration rates, maximum activity of cytochrome c oxidase, and active mitochondrial number consistently decreased in plants grown at elevated CO2 during the 9 months of the study when compared to ambient plants. Plant growth at elevated CO2 also reduced cytochrome pathway activity, but increased the activity of the alternative pathway. Despite all these effects seen in plants grown at high CO2, the specific oxygen uptake rate per unit of active mitochondria was the same for plants grown at ambient and elevated CO2. Although decreases in photorespiration activity have been pointed out as a factor contributing to the long-term acclimation of plant respiration to growth at elevated CO2, the homeostatic maintenance of specific respiratory rate per unit of mitochondria in response to high CO2 suggests that photorespiratory activity may play a small role on the long-term acclimation of respiration to elevated CO2. However, despite growth enhancement and as a result of the inhibition in cytochrome pathway activity by elevated CO2, total mitochondrial ATP production was decreased by plant growth at elevated CO2 when compared to ambient-grown plants. Because plant growth at elevated CO2 increased biomass but reduced respiratory machinery, activity, and ATP yields while maintaining O2 consumption rates per unit of mitochondria, we suggest that acclimation to elevated CO2 results from physiological adjustment of respiration to tissue ATP demand, which may not be entirely driven by nitrogen metabolism as previously suggested. PMID:17660349

Topobathymetric elevation model development using a new methodology: Coastal National Elevation Database

Science.gov (United States)

Danielson, Jeffrey J.; Poppenga, Sandra K.; Brock, John C.; Evans, Gayla A.; Tyler, Dean; Gesch, Dean B.; Thatcher, Cindy A.; Barras, John

2016-01-01

During the coming decades, coastlines will respond to widely predicted sea-level rise, storm surge, and coastalinundation flooding from disastrous events. Because physical processes in coastal environments are controlled by the geomorphology of over-the-land topography and underwater bathymetry, many applications of geospatial data in coastal environments require detailed knowledge of the near-shore topography and bathymetry. In this paper, an updated methodology used by the U.S. Geological Survey Coastal National Elevation Database (CoNED) Applications Project is presented for developing coastal topobathymetric elevation models (TBDEMs) from multiple topographic data sources with adjacent intertidal topobathymetric and offshore bathymetric sources to generate seamlessly integrated TBDEMs. This repeatable, updatable, and logically consistent methodology assimilates topographic data (land elevation) and bathymetry (water depth) into a seamless coastal elevation model. Within the overarching framework, vertical datum transformations are standardized in a workflow that interweaves spatially consistent interpolation (gridding) techniques with a land/water boundary mask delineation approach. Output gridded raster TBDEMs are stacked into a file storage system of mosaic datasets within an Esri ArcGIS geodatabase for efficient updating while maintaining current and updated spatially referenced metadata. Topobathymetric data provide a required seamless elevation product for several science application studies, such as shoreline delineation, coastal inundation mapping, sediment-transport, sea-level rise, storm surge models, and tsunami impact assessment. These detailed coastal elevation data are critical to depict regions prone to climate change impacts and are essential to planners and managers responsible for mitigating the associated risks and costs to both human communities and ecosystems. The CoNED methodology approach has been used to construct integrated TBDEM models

Undervisning af tosprogede elever

DEFF Research Database (Denmark)

Horst, Christian

2003-01-01

Artiklen fremdrager hovedresultaterne fra Virginia P. Collier's og Wayne P. Thomas's længdeundersøgelser af tosprogede elever i USA, som formentlig er de mest omfattende undersøgelser af undervisningen af tosprogede elever overhovedet. Resultaterne diskuteres i relation til udviklingen af en...

Elevation uncertainty in coastal inundation hazard assessments

Science.gov (United States)

Gesch, Dean B.; Cheval, Sorin

2012-01-01

Coastal inundation has been identified as an important natural hazard that affects densely populated and built-up areas (Subcommittee on Disaster Reduction, 2008). Inundation, or coastal flooding, can result from various physical processes, including storm surges, tsunamis, intense precipitation events, and extreme high tides. Such events cause quickly rising water levels. When rapidly rising water levels overwhelm flood defenses, especially in heavily populated areas, the potential of the hazard is realized and a natural disaster results. Two noteworthy recent examples of such natural disasters resulting from coastal inundation are the Hurricane Katrina storm surge in 2005 along the Gulf of Mexico coast in the United States, and the tsunami in northern Japan in 2011. Longer term, slowly varying processes such as land subsidence (Committee on Floodplain Mapping Technologies, 2007) and sea-level rise also can result in coastal inundation, although such conditions do not have the rapid water level rise associated with other flooding events. Geospatial data are a critical resource for conducting assessments of the potential impacts of coastal inundation, and geospatial representations of the topography in the form of elevation measurements are a primary source of information for identifying the natural and human components of the landscape that are at risk. Recently, the quantity and quality of elevation data available for the coastal zone have increased markedly, and this availability facilitates more detailed and comprehensive hazard impact assessments.

Chemical changes to leaf litter from trees grown under elevated CO2 and the implications for microbial utilization in a stream ecosystem

International Nuclear Information System (INIS)

Rier, S. T.; Tuchman, N. C.; Wetzel, R. G.

2005-01-01

The effects of elevated carbon dioxide on the chemistry and subsequent response of stream microorganisms growing on leaf litter of three riparian tree species (quaking aspen, white willow and sugar maple) were studied. Results showed that the effects were species-specific, i.e. aspen leaves contained high concentrations of lignin, maple leafs contained higher concentrations of soluble phenolic compounds and willow leaves contained higher concentrations of carbohydrate-bound condensed tannins. Initially, the higher concentrations of soluble phenolic compounds in maple leaves were rapidly leached in stream water, but overall, the impact of altered leaf chemistry on riparian trees grown under elevated carbon dioxide was clearly variable; no strongly suppressed microbial activity during stream incubation was observed. Any evidence of suppression observed, was species-specific. 49 refs., 2 tabs., 3 figs

Post-Closure Inspection Report for Corrective Action Unit 90: Area 2 Bitcutter Containment, Nevada Test Site, Nevada

International Nuclear Information System (INIS)

NSTec Environmental Restoration

2007-01-01

Corrective Action Unit (CAU) 90, Area 2 Bitcutter Containment, is identified in the ''Federal Facility Agreement and Consent Order'' of 1996. The post-closure requirements for CAU 90 are described in Section VII.B.8.b of the Nevada Test Site ''Resource Conservation and Recovery Act'' Permit for a Hazardous Waste Management Facility Number NEV HW0021, dated November 2005. Post-closure activities consist of the following: Semiannual inspections of the site using inspection checklists; Photographic documentation; Field note documentation; and Preparation and submittal of an annual Post-Closure Inspection Report. This annual report covers the period of July 2006 to June 2007 and consists of a summary of the results of the inspections, copies of the inspection checklists and field notes, maintenance and repair records (if any), photographs, and conclusions and recommendations. The inspection checklists are provided in Appendix A, a copy of the field notes is provided in Appendix B, and copies of photographs taken during the inspections are provided in Appendix C

Evaluation of weldment creep and fatigue strength-reduction factors for elevated-temperature design

International Nuclear Information System (INIS)

Corum, J.M.

1989-01-01

New explicit weldment strength criteria in the form of creep and fatigue strength-reduction factors were recently introduced into the American Society of Mechanical Engineers Code Case N-47, which governs the design of elevated-temperature nuclear plants components in the United States. This paper provides some of the background and logic for these factors and their use, and it describes the results of a series of long-term, confirmatory, creep-rupture and fatigue tests of simple welded structures. The structures (welded plates and tubes) were made of 316 stainless steel base metal and 16-8-2 weld filler metal. Overall, the results provide further substantiation of the validity of the strength-reduction factor approach for ensuring adequate life in elevated-temperature nuclear component weldments. 16 refs., 7 figs

Innovative modified hair follicle harvesting technique with reverse rake scalp elevator for lower occipital donor area in follicular unit extraction hair transplantation.

Science.gov (United States)

Gharwade, Chandrakant Rambhau

2016-01-01

Follicular unit extraction (FUE) is one of the widely practiced minimally invasive follicular harvesting techniques employed during hair transplantation. FUE technique has an advantage of utilising lower occipital area and supra-auricular region as a safe donor area described by Unger, in addition to the standard occipital donor area used in strip method (follicular unit transplant). Despite its potential advantages such as rapid recovery, minimal scarring and reduced post-operative pain; its widespread acceptance is limited due to various factors in variable contribution like steeper learning curve and potentially higher follicular transection rates (FTRs). The main practical drawbacks in harvesting FUE from lower occipital donor region that lie inferior to the standard donor area, is its acute angle (10°-15°) of emergent hair from scalp skin, higher variance angle (15°-35°) between hairs below the skin and hair exit angle above the skin and comparatively loose scalp, preventing to provide stable platform for punching. Hair transplant surgeon faces difficulty in aligning and engaging the FUE punch leading to very high hair follicle transection rate, and therefore, it is not a preferred site for harvesting follicles in FUE. Authors description of modified technique using reverse rake scalp elevator helps in negating the acute angle of the hair follicles exit from scalp skin and reducing the variance angle between emergent hair and hair below the skin in lower occipital region thereby reducing FTR. Furthermore, an added advantage of reducing the overall operative time and surgeon fatigue, improve donor area healing, availability of a comparatively larger donor area which increases the confidence of the beginners. This method will be of help as it is easy to duplicate and follow by novice hair transplant surgeons and also for those who are routinely doing mega hair transplants sessions.

Innovative modified hair follicle harvesting technique with reverse rake scalp elevator for lower occipital donor area in follicular unit extraction hair transplantation

Directory of Open Access Journals (Sweden)

Chandrakant Rambhau Gharwade

2016-01-01

Full Text Available Follicular unit extraction (FUE is one of the widely practiced minimally invasive follicular harvesting techniques employed during hair transplantation. FUE technique has an advantage of utilising lower occipital area and supra-auricular region as a safe donor area described by Unger, in addition to the standard occipital donor area used in strip method (follicular unit transplant. Despite its potential advantages such as rapid recovery, minimal scarring and reduced post-operative pain; its widespread acceptance is limited due to various factors in variable contribution like steeper learning curve and potentially higher follicular transection rates (FTRs. The main practical drawbacks in harvesting FUE from lower occipital donor region that lie inferior to the standard donor area, is its acute angle (10°–15° of emergent hair from scalp skin, higher variance angle (15°–35° between hairs below the skin and hair exit angle above the skin and comparatively loose scalp, preventing to provide stable platform for punching. Hair transplant surgeon faces difficulty in aligning and engaging the FUE punch leading to very high hair follicle transection rate, and therefore, it is not a preferred site for harvesting follicles in FUE. Authors description of modified technique using reverse rake scalp elevator helps in negating the acute angle of the hair follicles exit from scalp skin and reducing the variance angle between emergent hair and hair below the skin in lower occipital region thereby reducing FTR. Furthermore, an added advantage of reducing the overall operative time and surgeon fatigue, improve donor area healing, availability of a comparatively larger donor area which increases the confidence of the beginners. This method will be of help as it is easy to duplicate and follow by novice hair transplant surgeons and also for those who are routinely doing mega hair transplants sessions.

Short-term effects of fertilization on photosynthesis and leaf morphology of field-grown loblolly pine following long-term exposure to elevated CO2 concentration

International Nuclear Information System (INIS)

Maier, C.A.; Palmroth, S.; Ward, E.

2008-01-01

This study examined the effects of an initial nitrogen (N) fertilizer application on the upper-canopy needle morphology and gas exchange of a loblolly pine tree exposed to elevated carbon dioxide (CO 2 ) concentrations over a period of 9 years. Plots in the study were split, and one half of each plot was fertilized with 112 kg ha -1 of elemental N. Measurements included needle length, mass per unit area, N concentrations on a mass and area basis, light-saturated net photosynthesis per unit leaf area, and per unit mass and leaf conductance. Results of the study showed that fertilization had little impact on needle length, mass per unit area, or leaf conductance. Results suggested that although both needle age classes accumulated N following fertilization, current-year foliage incorporated N into its photosynthetic machinery, while 1-year old foliage stored N. No significant interactions were observed between elevated CO 2 and light-saturated net photosynthesis per unit leaf area. The study found few fertilization and CO 2 interaction effects on leaf physiology and morphology. 54 refs., 3 tabs., 3 figs

Analysis on Containment Response Following a LBLOCA of APR1400

International Nuclear Information System (INIS)

Han, Kyu Hyun

2016-01-01

The predictions are in good agreements with the final safety analysis report, which implies the containment integrity is maintained during or after an accident like loss of coolant accident. In this study, the CONTEMPT-LT/028 was used to calculate the pressure and temperature, and in the follow-up study, CONTAIN 2.0 will be used for the pressure and temperature predictions in APR1400 reactors. Shin-Hanul Units 1 and 2 may possess different characteristics of peak pressure and temperature in containment following a large break loss-of-coolant-accident. To assess the important performance independently and to compare with prediction results presented in the final safety analysis report (FSAR) of Shin-Hanul Units 1 and 2 might be helpful to regulatory review for identifying validity of the FSAR. The end of blowdown (EOB) time during a LOCA could largely affect the peak pressure and temperature in the containment. This paper provides CONTEMPT-LT/028 prediction of the peak pressure and temperature of Shin-Hanul Units 1 and 2 following a large break loss-of-coolant-accident and compares with licensee's prediction results.

Analysis on Containment Response Following a LBLOCA of APR1400

Energy Technology Data Exchange (ETDEWEB)

Han, Kyu Hyun [KINS, Daejeon (Korea, Republic of)

2016-05-15

The predictions are in good agreements with the final safety analysis report, which implies the containment integrity is maintained during or after an accident like loss of coolant accident. In this study, the CONTEMPT-LT/028 was used to calculate the pressure and temperature, and in the follow-up study, CONTAIN 2.0 will be used for the pressure and temperature predictions in APR1400 reactors. Shin-Hanul Units 1 and 2 may possess different characteristics of peak pressure and temperature in containment following a large break loss-of-coolant-accident. To assess the important performance independently and to compare with prediction results presented in the final safety analysis report (FSAR) of Shin-Hanul Units 1 and 2 might be helpful to regulatory review for identifying validity of the FSAR. The end of blowdown (EOB) time during a LOCA could largely affect the peak pressure and temperature in the containment. This paper provides CONTEMPT-LT/028 prediction of the peak pressure and temperature of Shin-Hanul Units 1 and 2 following a large break loss-of-coolant-accident and compares with licensee's prediction results.

Permanent monitoring of containment integrity: the sexten system

International Nuclear Information System (INIS)

Germain, J.L.; Janneteau, E.

1993-01-01

Reactor containment integrity is of prime importance to the safety of PWR units. It is checked by means of tests performed at high pressure during the containment building pressure tests. These periodical tests are supplemented in France by permanent monitoring using the SEXTEN system. First feasibility tests for this system were carried out in 1980. The encouraging results obtained led to the development of a prototype, followed by an industrial system which has since been installed in all French PWR units. This system measures the containment leak rate, with corrections for the compressed air intakes used by the air-operated valves. Leaktightness is expressed in terms of the leak rate for a 60 mbar overpressure. If the leak rate exceeds a fixed limit value, leak detection operations are initiated, using SEXTEN. A new version of the system, known as SEXTEN 2 is being developed. (authors). 2 figs

The regulatory approach to the assessment of containment structures in the United Kingdom, with reference to the proposed Sizewell 'B' project

International Nuclear Information System (INIS)

Todd, I.W.

1988-01-01

The regulation of nuclear installations in the United Kingdom is carried out by means of a licensing system which is administered on behalf of the Health and Safety Executive (HSE) by HM Nuclear Installations Inspectorate. A major part of this process lies in the assessment of an installation's designs and safety case, which must be submitted to the Inspectorate before a licence may be granted. This paper describes the work carried out in assessing the design proposed for the containment structure of the United Kingdom's first PWR, Sizewell 'B'. The roles of the Inspectorate's Safety Assessment Principles, and the engineering judgement of the individual assessor, are discussed. The reasons behind the Inspectorate's decision to commission independent design studies of the structure are explained, and the results of these studies are presented in outline. Views are also expressed upon the validation of analytical results, quality assurance, and further work planned by the Inspectorate in this field. The paper concludes that it is the flexibility and discretion allowed by the above approach which represents the principal strength of the UK's system of regulatory assessment. (author)

Effects of elevated CO

NARCIS (Netherlands)

Xue, Sha; Yang, Xiaomei; Liu, Guobin; Gai, Lingtong; Zhang, Changsheng; Ritsema, Coen J.; Geissen, Violette

2017-01-01

Elevated CO₂ and drought are key consequences of climate change and affect soil processes and plant growth. This study investigated the effects of elevated CO₂ and drought on the microbial biomass and enzymatic activities in the rhizospheres of Bothriochloa ischaemum and

Plastic responses to elevated temperature in low and high elevation populations of three grassland species.

Science.gov (United States)

Frei, Esther R; Ghazoul, Jaboury; Pluess, Andrea R

2014-01-01

Local persistence of plant species in the face of climate change is largely mediated by genetic adaptation and phenotypic plasticity. In species with a wide altitudinal range, population responses to global warming are likely to differ at contrasting elevations. In controlled climate chambers, we investigated the responses of low and high elevation populations (1200 and 1800 m a.s.l.) of three nutrient-poor grassland species, Trifolium montanum, Ranunculus bulbosus, and Briza media, to ambient and elevated temperature. We measured growth-related, reproductive and phenological traits, evaluated differences in trait plasticity and examined whether trait values or plasticities were positively related to approximate fitness and thus under selection. Elevated temperature induced plastic responses in several growth-related traits of all three species. Although flowering phenology was advanced in T. montanum and R. bulbosus, number of flowers and reproductive allocation were not increased under elevated temperature. Plasticity differed between low and high elevation populations only in leaf traits of T. montanum and B. media. Some growth-related and phenological traits were under selection. Moreover, plasticities were not correlated with approximate fitness indicating selectively neutral plastic responses to elevated temperature. The observed plasticity in growth-related and phenological traits, albeit variable among species, suggests that plasticity is an important mechanism in mediating plant responses to elevated temperature. However, the capacity of species to respond to climate change through phenotypic plasticity is limited suggesting that the species additionally need evolutionary adaptation to adjust to climate change. The observed selection on several growth-related and phenological traits indicates that the study species have the potential for future evolution in the context of a warming climate.

Solution-processable red-emission organic materials containing triphenylamine and benzothiodiazole units: synthesis and applications in organic light-emitting diodes.

Science.gov (United States)

Yang, Yi; Zhou, Yi; He, Qingguo; He, Chang; Yang, Chunhe; Bai, Fenglian; Li, Yongfang

2009-06-04

Three solution-processable red-emissive organic materials with a hole-transporting unit triphenylamine (TPA) as the core part and a D-pi-A bipolar structure as the branch part, TPA-BT (single-branched molecule), b-TPA-BT (bibranched molecule), and t-TPA-BT (tribranched molecule), were synthesized by the Heck coupling reaction. Herein, for the D-pi-A push-pull structure, we use TPA as the electron donor, benzothiodiazole (BT) as the electron acceptor, and the vinylene bond as the pi-bridge connecting the TPA and BT units. The compounds exhibit good solubility in common organic solvents, benefited from the three-dimensional spatial configuration of TPA units and the branch structure of the molecules. TPA-BT, b-TPA-BT, and t-TPA-BT show excellent photoluminescent properties with maximum emission peaks at ca. 630 nm. High-performance red-emission organic light-emitting diodes (OLEDs) were fabricated with the active layer spin coated from a solution of these compounds. The OLED based on TPA-BT displayed a low turn-on voltage of 2.0 V, a maximum luminance of 12192 cd/m2, and a maximum current efficiency of 1.66 cd/A, which is among the highest values for the solution-processed red-emission OLEDs. In addition, high-performance white-light-emitting diodes (WLEDs) with maximum luminance around 4400 cd/m2 and maximum current efficiencies above 4.5 cd/A were realized by separately doping the three TPA-BT-containing molecules as red emitter and poly(6,6'-bi-(9,9'-dihexylfluorene)- co-(9,9'-dihexylfluorene-3-thiophene-5'-yl)) as green emitter into blue poly(9,9-dioctylfluorene-2,7-diyl) host material with suitable weight ratios.

Toll Facilities in the United States - Toll Facilities in the United States

Data.gov (United States)

Department of Transportation — Biennial report containing selected information on toll facilities in the United States that has been provided to FHWA by the States and/or various toll authorities...

Elevated Striatal Dopamine Function in Immigrants and Their Children: A Risk Mechanism for Psychosis.

Science.gov (United States)

Egerton, Alice; Howes, Oliver D; Houle, Sylvain; McKenzie, Kwame; Valmaggia, Lucia R; Bagby, Michael R; Tseng, Huai-Hsuan; Bloomfield, Michael A P; Kenk, Miran; Bhattacharyya, Sagnik; Suridjan, Ivonne; Chaddock, Chistopher A; Winton-Brown, Toby T; Allen, Paul; Rusjan, Pablo; Remington, Gary; Meyer-Lindenberg, Andreas; McGuire, Philip K; Mizrahi, Romina

2017-03-01

Migration is a major risk factor for schizophrenia but the neurochemical processes involved are unknown. One candidate mechanism is through elevations in striatal dopamine synthesis and release. The objective of this research was to determine whether striatal dopamine function is elevated in immigrants compared to nonimmigrants and the relationship with psychosis. Two complementary case-control studies of in vivo dopamine function (stress-induced dopamine release and dopamine synthesis capacity) in immigrants compared to nonimmigrants were performed in Canada and the United Kingdom. The Canadian dopamine release study included 25 immigrant and 31 nonmigrant Canadians. These groups included 23 clinical high risk (CHR) subjects, 9 antipsychotic naïve patients with schizophrenia, and 24 healthy volunteers. The UK dopamine synthesis study included 32 immigrants and 44 nonimmigrant British. These groups included 50 CHR subjects and 26 healthy volunteers. Both striatal stress-induced dopamine release and dopamine synthesis capacity were significantly elevated in immigrants compared to nonimmigrants, independent of clinical status. These data provide the first evidence that the effect of migration on the risk of developing psychosis may be mediated by an elevation in brain dopamine function. © The Author 2017. Published by Oxford University Press on behalf of the Maryland Psychiatric Research Center.

Precipitation of iron species on the cold side of PWR steam generator and its possible correlation to dose rate elevation

International Nuclear Information System (INIS)

Bengtsson, Bernt; Chen, Jiaxin; Andersson, Petter

2014-01-01

For the last 10 years of service of Ringhals PWR unit 4, operating with Alloy-600MA steam generator tubing materials and a coolant pH of 7.2 (a)300°C, the cold water channel heads experienced continuous dose rate elevation. In the hot parts, however, it remained stable. Similar observations were made in Ringhals unit 2 and 3 after SGR to Alloy 690 and sometimes in other PWRs operated at similarly 'low' pH-regime. Following the introduction of elevated pH regime at Ringhals PWRs the cold side dose rates dropped to the similar levels as on the hot side. The phenomena are analysed in this paper from three different aspects: (1) the general plant observations in dose rate development under different coolant pH regimes; (2) the concentrations of dissolved and soluble iron species at the low and high coolant pH values and (3) the microstructures of the oxide films formed on the cold and hot sides of a steam generator tube pulled from a retired steam generator. Based on the analyses a hypothesis is elaborated that the formation of a thin but highly radioactive layer of iron-rich oxide deposit on the cold side may be responsible for the dose rate elevation and that its formation may be harder at the elevated pH regime. (author)

Hanford Site Waste Managements Units reports

International Nuclear Information System (INIS)

1992-01-01

The Hanford Site Waste Management Units Report (HSWMUR) was originated to provide information responsive to Section 3004(u) of the Hazardous and Solid Waste Amendments (HSWA) of the 1984 United States Code (USC 1984). This report provides a comprehensive inventory of all types of waste management units at the Hanford Site, including a description of the units and the waste they contain. Waste management units in this report include: (1) Resource Conservation and Recovery Act of 1976 (RCRA) disposal units, (2) Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) disposal units, (3) unplanned releases, (4) inactive contaminated structures, (5) RCRA treatment, storage, and disposal (TSD) units, and (6) other storage areas. Because of the comprehensive nature of this report, the listing of sites is more extensive than required by Section 3004(u) of HSWA. The information in this report is extracted from the Waste Information Data System (WIDS). The WIDS provides additional information concerning the waste management units contained in this report and is maintained current with changes to these units. This report is updated annually if determined necessary per the Hanford Federal Facility Agreement and Consent Order Order (commonly referred to as the Tri-Party Agreement, Ecology et al. 1990). This report identifies 1,414 waste management units. Of these, 1,015 units are identified as solid waste management units (SWMU), and 342 are RCRA treatment, storage, and disposal units. The remaining 399 are comprised mainly of one-time spills to the environment, sanitary waste disposal facilities (i.e., septic tanks), and surplus facilities awaiting decontamination and decommissioning

History of Elevators and Related Research

Science.gov (United States)

Abe, Shigeru; Watanabe, Eiki

The history of traction drive elevators in Japan is described. The electrical technologies such as the microprocessor car control and the VVVF motor control made remarkable progress leading to higher reliability and energy savings. Then, the various machine-room-less elevators have been developed and the space saving technology, such as the shuttle and the double-deck elevators become important, too. The elevators used for evacuation in case of emergencies are also discussed.

Michelson-Morley in Einstein's elevators

Science.gov (United States)

Pierce, Fred; Pierce, Ayal

2010-02-01

Experiments are proposed in which a Michelson-Morley interferometer is placed in Einstein's thought experiments where elevators are subjected to varied accelerated fields. Unbeknownst to the observers inside the elevators, they are placed in different circumstances: on the surface of the Earth, in free fall, in space distant from any mass, and inside a rotating space station. By use of not one, but two objects, the observer will be challenged to determine the nature and shape of the accelerated field, if any, inside the elevator. It will be demonstrated that the nature of the accelerated field can be determined easily from inside the elevator by the motion of the two objects released by the observer. It will also be shown that, for the elevator on the space station which is generating an ``artificial gravity'' field by rotation, Michelson-Morley would have the same null result as on Earth. However, the Michelson-Morley experiment is adapted so that in addition to the two horizontal arms of the interferometer (parallel to the floor of the elevator) a vertical arm is added perpendicular to the floor facing towards the ceiling. Such a vertical arm added to the Michelson-Morley experiment adds a new dimension to examining each accelerated field, including gravity. )

Evaluation of an air drilling cuttings containment system

Energy Technology Data Exchange (ETDEWEB)

Westmoreland, J.

1994-04-01

Drilling at hazardous waste sites for environmental remediation or monitoring requires containment of all drilling fluids and cuttings to protect personnel and the environment. At many sites, air drilling techniques have advantages over other drilling methods, requiring effective filtering and containment of the return air/cuttings stream. A study of. current containment methods indicated improvements could be made in the filtering of radionuclides and volatile organic compounds, and in equipment like alarms, instrumentation or pressure safety features. Sandia National Laboratories, Dept. 61 11 Environmental Drilling Projects Group, initiated this work to address these concerns. A look at the industry showed that asbestos abatement equipment could be adapted for containment and filtration of air drilling returns. An industry manufacturer was selected to build a prototype machine. The machine was leased and put through a six-month testing and evaluation period at Sandia National Laboratories. Various materials were vacuumed and filtered with the machine during this time. In addition, it was used in an actual air drive drilling operation. Results of these tests indicate that the vacuum/filter unit will meet or exceed our drilling requirements. This vacuum/filter unit could be employed at a hazardous waste site or any site where drilling operations require cuttings and air containment.

Standard test methods for elevated temperature tension tests of metallic materials

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 These test methods cover procedure and equipment for the determination of tensile strength, yield strength, elongation, and reduction of area of metallic materials at elevated temperatures. 1.2 Determination of modulus of elasticity and proportional limit are not included. 1.3 Tension tests under conditions of rapid heating or rapid strain rates are not included. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Resistance of human erythrocytes containing elevated levels of vitamin E to radiation-induced hemolysis

International Nuclear Information System (INIS)

Brown, M.A.

1983-01-01

Human erythrocytes were isolated from the blood of healthy donors and then incubated in the presence of suspensions of alpha-tocopherol for 30 min at 37 degrees C. Unabsorbed tocopherol was removed by centrifugation using several washes of isotonic phosphate-buffered saline. Washed erythrocytes were resuspended to 0.05%. Hct and exposed to hemolyzing doses of 60 Co gamma radiation, and hemolysis was monitored continuously by light scattering at 700 nm in a recording spectrophotometer. The extent of hemolysis with time was sigmoid and data analysis was carried out on the time taken for 50% hemolysis to occur (t50%). The vitamin E content of erythrocytes was significantly elevated by the incubation procedure and resulted in the cells exhibiting a significantly increased resistance to hemolysis as reflected by the extended t50% values. Oral supplementation of 500 IU of vitamin E per day to eight normal human subjects for a period of 16 days also resulted in their washed erythrocytes exhibiting a significant increase in resistance to radiation-induced hemolysis. When comparing vitamin E incubated cells with control cells, both the dose-reducing factor (DRF) and the time for 50% hemolysis quotient (Qt50%) were observed to increase with increasing radiation dose

Broadband phase-preserved optical elevator

OpenAIRE

Luo, Yuan; Han, Tiancheng; Zhang, Baile; Qiu, Cheng-Wei; Barbastathis, George

2011-01-01

Phase-preserved optical elevator is an optical device to lift up an entire plane virtually without distortion in light path or phase. Using transformation optics, we have predicted and observed the realization of such a broadband phase-preserved optical elevator, made of a natural homogeneous birefringent crystal without resorting to absorptive and narrowband metamaterials involving time-consuming nano-fabrication. In our demonstration, the optical elevator is designed to lift a sheet upwards...

Thyroglobulin recovery test of sera containing elevated levels of anti-thyroglobulin antibodies

International Nuclear Information System (INIS)

Hervas, I.; Gonzalez-Cabezas, P.; Flores, D.; Perez-Pastor, J.L.; Bello, P.; Rivas, A.; Alonso, J.; Olivas, C.; Mateo, A.

2002-01-01

Aim: Thyroglobulin (Tg) is a macro-molecule synthesized exclusively in the thyroid gland for the synthesis of thyroid hormones. In differentiated thyroid carcinoma, after radical thyroidectomy, the discovering of measurable quantities of Tg can be indicator of relapse y/or spread of disease but Thyroglobulin antibodies can alter the determination of Tg. The aim of this study is to assess and measure the interference of Tg antibodies on the Tg determination. Methods: We have selected 50 consecutive serum whose Tg-antibodies levels were higher than the normality values (0-100 UI/mL). Tg-antibodies were measured using a 'sandwich' radioimmunometric assay on solid phase. We have performed a recovery test on these sera. This test consists on adding a known quantity (50 UI) of Tg on that sera and then measure the Tg values to find out the percentage of Tg that is recuperated. Tg was measured using a radioimmunometric assay on solid phase. Results: Sera were divided in two groups: A.- 15 sera with Tg-antibodies levels between 100-250 UI/mL: 85% of them presented a Tg recovery percentage higher than 90% (Tg-antibodies did not interfere on Tg values due to Tg was recovered almost in its totality). B.- 53 sera with Tg-antibodies levels higher than 250 UI/mL: Only 10% of them presented a Tg recovery percentage higher than >90% . (90% of sera interfered on Tg values). 70% of that sera presented percentages under 50%. The Pearson's correlation coefficient between Tg-antibodies and Tg recovery percentage was -0.34. Conclusions: The majority (90%)of sera with Tg-antibodies higher than 250 UI/mL presented an high interference on Tg determination. However the majority of sera with Tg-antibodies between 100-250 did not show any interference on Tg determination. There are not linear correlation between highest values and lowest percentages of Tg recovered. We recommend the realization of Tg recovery test on sera with elevated Tg antibodies specially when are higher than 250 UI/mL

Molten material-containing vessel

International Nuclear Information System (INIS)

Akagawa, Katsuhiko

1998-01-01

The molten material-containing vessel of the present invention comprises a vessel main body having an entrance opened at the upper end, a lid for closing the entrance, an outer tube having an upper end disposed at the lower surface of the lid, extended downwardly and having an closed lower end and an inner tube disposed coaxially with the outer tube. When a molten material is charged from the entrance to the inside of the vessel main body of the molten material-containing vessel and the entrance is closed by the lid, the outer tube and the inner tube are buried in the molten material in the vessel main body, accordingly, a fluid having its temperature elevated by absorption of the heat of the molten material rises along the inner circumferential surface of the outer tube, abuts against the lower surface of the lid and cooled by exchanging heat with the lid and forms a circulating flow. Since the heat in the molten material is continuously absorbed by the fluid, transferred to the lid and released from the lid to the atmospheric air, heat releasing efficiency can be improved compared with conventional cases. (N.H.)

HYDRAULIC ELEVATOR INSTALLATION ESTIMATION FOR THE WATER SOURCE WELL SAND-PACK CLEANING UP

Directory of Open Access Journals (Sweden)

V. V. Ivashechkin

2016-01-01

Full Text Available The article offers design of a hydraulic elevator installation for cleaning up water-source wells of sand packs. It considerers the installation hydraulic circuit according to which the normal pump feeds the high-level tank water into the borehole through two parallel water lines. The water-jet line with washing nozzle for destroying the sand-pack and the supply pipe-line coupled with the operational nozzle of the hydraulic elevator containing the inlet and the supply pipelines for respectively intaking the hydromixture and removing it from the well. The paper adduces equations for fluid motion in the supply and the water-jet pipelines and offers expressions for evaluating the required heads in them. For determining water flow in the supply and the water-jet pipe lines the author proposes to employ graphical approach allowing finding the regime point in Q–H chart by means of building characteristics of the pump and the pipe-lines. For calculating the useful vertical head, supply and dimensions of the hydraulic elevator the article employs the equation of motion quantity with consistency admission of the motion quantity before and after mixing the flows in the hydraulic elevator. The suggested correlations for evaluating the hydraulic elevator efficiency determine the sand pack removal duration as function of its sizes and the ejected fluid flow rate. A hydraulic-elevator installation parameters estimation example illustrates removing a sand pack from a water-source borehole of 41 m deep and 150 mm diameter bored in the village of Uzla of Myadelsk region, of Minsk oblast. The working efficiency of a manufactured and laboratory tested engineering prototype of the hydraulic elevator installation was acknowledged in actual tests at the indicated borehole site. With application of graphical approach, the suggested for the hydraulic elevator installation parameters calculation procedure allows selecting, with given depth and the borehole diameter

Interaktive tavler - interaktive elever

DEFF Research Database (Denmark)

Reusch, Charlotte F.; Otzen, Elsebeth

Abstract, Poster-præsentation 13.-14. juni 2012, Pilotprojekt: Interaktive tavler – interaktive elever Lektor, cand. pæd., Elsebeth Otzen og Lektor, cand. mag., Charlotte Reusch, Institut for Skole og Læring, Læreruddannelsen, Professionshøjskolen Metropol, København Hvordan motiverer en interaktiv...... tavle lærere og elever? Hvad sker der mellem elev, stof og lærer, når læreren bliver i stand til at billedliggøre og dynamisere sine oplæg på tavlen? Bliver læreroplæg prioriteret? Bliver eleverne aktive, eller ender den interaktive tavle med blot at understøtte lærerens envejskommunikation til klassen......? Og hvad sker der mellem eleverne? Disse spørgsmål var igangsættende for arbejdet med pilotprojektet Interaktive tavler – interaktive elever, som blev afviklet i skoleåret 2010-2011. Projektet blev udført af en tværfaglig gruppe, bestående af lektorer i matematik, biologi og dansk i læreruddannelsen...

Interaktive tavler - interaktive elever

DEFF Research Database (Denmark)

Reusch, Charlotte; Otzen, Elsebeth

Abstract, Poster-præsentation 13.-14. juni 2012, Pilotprojekt: Interaktive tavler ? interaktive elever Lektor, cand. pæd., Elsebeth Otzen og Lektor, cand. mag., Charlotte Reusch, Institut for Skole og Læring, Læreruddannelsen, Professionshøjskolen Metropol, København Hvordan motiverer en interaktiv...... tavle lærere og elever? Hvad sker der mellem elev, stof og lærer, når læreren bliver i stand til at billedliggøre og dynamisere sine oplæg på tavlen? Bliver læreroplæg prioriteret? Bliver eleverne aktive, eller ender den interaktive tavle med blot at understøtte lærerens envejskommunikation til klassen......? Og hvad sker der mellem eleverne? Disse spørgsmål var igangsættende for arbejdet med pilotprojektet Interaktive tavler ? interaktive elever, som blev afviklet i skoleåret 2010-2011. Projektet blev udført af en tværfaglig gruppe, bestående af lektorer i matematik, biologi og dansk i læreruddannelsen...

Elevation data for floodplain mapping

National Research Council Canada - National Science Library

Committee on Floodplain Mapping Technologies; National Research Council; Division on Earth and Life Studies; National Research Council

2007-01-01

.... Elevation Data for Floodplain Mapping shows that there is sufficient two-dimensional base map imagery to meet FEMA's flood map modernization goals, but that the three-dimensional base elevation data...

High-resolution Monthly Satellite Precipitation Product over the Conterminous United States

Science.gov (United States)

Hashemi, H.; Fayne, J.; Knight, R. J.; Lakshmi, V.

2017-12-01

We present a data set that enhanced the Tropical Rainfall Measuring Mission (TRMM) Multi-satellite Precipitation Analysis (TMPA) monthly product 3B43 in its accuracy and spatial resolution. For this, we developed a correction function to improve the accuracy of TRMM 3B43, spatial resolution of 25 km, by estimating and removing the bias in the satellite data using a ground-based precipitation data set. We observed a strong relationship between the bias and land surface elevation; TRMM 3B43 tends to underestimate the ground-based product at elevations above 1500 m above mean sea level (m.amsl) over the conterminous United States. A relationship was developed between satellite bias and elevation. We then resampled TRMM 3B43 to the Digital Elevation Model (DEM) data set at a spatial resolution of 30 arc second ( 1 km on the ground). The produced high-resolution satellite-based data set was corrected using the developed correction function based on the bias-elevation relationship. Assuming that each rain gauge represents an area of 1 km2, we verified our product against 9,200 rain gauges across the conterminous United States. The new product was compared with the gauges, which have 50, 60, 70, 80, 90, and 100% temporal coverage within the TRMM period of 1998 to 2015. Comparisons between the high-resolution corrected satellite-based data and gauges showed an excellent agreement. The new product captured more detail in the changes in precipitation over the mountainous region than the original TRMM 3B43.

Dual swing-up elevator well drilling apparatus

Energy Technology Data Exchange (ETDEWEB)

Ahmad, H.; Vorarittinapa, T.

1984-09-18

A well drilling apparatus includes a first swing-up elevator platform on which the mast structure is pivotally mounted. After the mast structure has been raised to its erect position, the first elevator platform is elevated to carry the mast structure to a high operational level. A second swing-up elevator platform is provided to carry the drawworks to the same high level at which the two elevator platforms are coupled together to form the working floor. All of the raising and elevating operations can be accomplished with power supplied by the drawworks. The elevator platforms may be lowered after the drilling operation has been accomplished without interfering with any control valve structures that have been placed on the wellhead while the structure was at its raised operational level; the swing-up elevator platforms swing down in opposite directions over any such valve structure.

Kuosheng BWR/6 containment safety analysis with gothic code

International Nuclear Information System (INIS)

Lin Ansheng; Wang Jongrong; Yuann Rueyyng; Shih Chunkuan

2011-01-01

Kuosheng Nuclear Power Plant in Taiwan is a GE-designed twin-unit BWR/6 plant, each unit rated at 2894 MWt. In this study, we presented the calculated results of the containment pressure and temperature responses after the main steam line break accident, which is the design basis for the containment system. During the simulation, a power of SPU range (105.1%) was used and a model of the Mark III type containment was built using the containment thermal-hydraulic program GOTHIC. The simulation consists of short and long-term responses. The drywell pressure and temperature responses which display the maximum values in the early state of the LOCA were investigated in the short-term response; the primary containment pressure and temperature responses in the long-term response. The blowdown flow was provided by FSAR and used as boundary conditions in the short-term model; in the long-term model, the blowdown flow was calculated using a GOTHIC built-in homogeneous equilibrium model. In the long-term analysis, a simplifier RPV model was employed to calculate the blowdown flow. Finally, the calculated results, similar to the FSAR results, indicate the GOTHIC code has the capability to simulate the pressure/temperature response of Mark III containment to the main steam line break LOCA. (author)

Acute ST-Elevation Myocardial Infarction, a Unique Complication of Recreational Nitrous Oxide Use.

Science.gov (United States)

Indraratna, Praveen; Alexopoulos, Chris; Celermajer, David; Alford, Kevin

2017-08-01

A 28-year-old male was admitted to hospital with an acute ST-elevation myocardial infarction. This was in the context of recreational abuse of nitrous oxide. The prevalence of nitrous oxide use in Australia has not been formally quantified, however it is the second most commonly used recreational drug in the United Kingdom. Nitrous oxide has previously been shown to increase serum homocysteine levels. This patient was discovered to have an elevated homocysteine level at baseline, which was further increased after nitrous oxide consumption. Homocysteine has been linked to endothelial dysfunction and coronary atherosclerosis and this case report highlights one of the dangers of recreational abuse of nitrous oxide. Copyright © 2017 Australian and New Zealand Society of Cardiac and Thoracic Surgeons (ANZSCTS) and the Cardiac Society of Australia and New Zealand (CSANZ). Published by Elsevier B.V. All rights reserved.

Design experiments for a vented containment

International Nuclear Information System (INIS)

Hesboel, R.

1985-01-01

A filtered containment venting system, operable late in 1985, is currently under installation at the Barsebaeck twin nuclear power station in Sweden. The filter unit, which communicates with the containments of both reactor units, but is separated from them by rupture discs, consists of a concrete bed, 40 m high and 20 m in diameter, filled with gravel of grain size 25-35 mm. The performance of the gravel bed under such accident conditions which might lead to an activation of this safeguard system has been the subject for investigation within the FILTRA project. These investigations have shown that the gravel bed acts as: an expansion volume for decreasing gas pressure and increasing gas residence time, a heat sink for condensing steam, an excellent filter medium for removing aerosols and elemental iodine, and a sump volume for collecting radioactive condensate. The results from iodine retention studies in gravel beds are mainly considered

REPERFUSION THERAPY IN ACUTE CORONARY SYNDROME WITH ST SEGMENT ELEVATION

Directory of Open Access Journals (Sweden)

A. L. Alyavi

2016-01-01

Full Text Available Aim. To compare effect of percutaneous balloon angioplasty (PCA and a systemic thrombolysis (STL on the central and intracardiac hemodynamics in patients with acute coronary syndrome (ACS with ST segment elevation.Material and methods. 80 patients with ACS with ST segment elevation were included in the study. Patients were split into 2 groups depending on reperfusion strategy. PCA was performed in 55 patients (first group. 25 patients of the second group had STL with Streptokinase, i/v, 1 500 000 units per hour. Echocardiography was performed in all patients at admission and after 3 and 7 days of treatment to evaluate intracardiac hemodynamics.Results. Both reperfusion methods significantly increase of ejection fraction (EF and maximal output speed of left ventricle (LV. Increase of LV EF in patients after PCA was higher than this in patients after STL. PCA improved LV diastolic function; STL did not change this characteristic. After PCA working diagnosis of ACS was transformed to the following final diagnosis: acute myocardial infarction (AMI with Q, AMI without Q and unstable angina in 37,5, 30,4 and 32,1% of patients, respectively. After STL diagnosis of AMI with Q was defined in all patients.Conclusion. PCA in patients with ACS with ST segment elevation results in fast improvement of global systolic and diastolic LV function. Besides, PCA prevents AMI with Q in a half of these patients.

CSER 95-002: ALARA shielding for IAEA SNM container movement

International Nuclear Information System (INIS)

Miller, E.M.

1995-01-01

This CSER qualifies use of a 5% borated, lead foil lined polyethylene 1 inch annulus as a bucket and in a small carrier to move sealed containers of plutonium. The containers are Oversize Cans or smaller containing plutonium limited in mass and H/Pu ratio by PFP storage and transportation CPS's. These ALARA shielding units reduce personnel exposure to the radiation from the containers as they are moved for assay and other required activities

Insulators containing CuCl4X22- (X=H2O, NH3) units: Origin of the orthorhombic distortion observed only for CuCl4(H2O)22-

DEFF Research Database (Denmark)

García-Fernández, P.; García Lastra, Juan Maria; Trueba, A.

2012-01-01

The origin of the difference in structure between compounds containing CuCl4X22- (X=H2O, NH3) units is analyzed by means of first-principles calculations. While NH3-containing compounds display tetragonal symmetry, H2O-containing ones display an orthorhombic distortion at low temperature where...... the equatorial Cl- ions are no longer equivalent. Our simulations of optical and vibrational transitions show good agreement with all available experimental optical absorption and Raman data. As a salient feature, the value of the force constant for the B1g mode, K(B1g), driving the orthorhombic distortion......CuCl4(H2O)2 has a local origin....

Red cell distribution width is associated with hemoglobin A1C elevation, but not glucose elevation.

Science.gov (United States)

Bao, Xue; Wan, Min; Gu, Yeqing; Song, Yanqi; Zhang, Qing; Liu, Li; Meng, Ge; Wu, Hongmei; Xia, Yang; Shi, HongBin; Su, Qian; Fang, Liyun; Yang, Huijun; Yu, Fei; Sun, Shaomei; Wang, Xing; Zhou, Ming; Jia, Qiyu; Song, Kun; Wang, Guolin; Yu, Ming; Niu, Kaijun

2017-10-01

To investigate the association between red cell distribution width (RDW) and elevation of glucose/glycated hemoglobin (HbA1c). An analysis was conducted using data from a prospective cohort study of adults. People without prediabetes or diabetes (n=7,795) were followed for a mean of 2.90years (range: 1-7years, 95% confidence interval: 2.86-2.94years). Glucose elevation is defined as fasting glucose levels exceeding 5.6mmol/l, or 2-hour glucose values in the oral glucose tolerance test exceeding 7.8mmol/l. HbA1c elevation is defined as a HbA1c value exceeding a normal limit of 39mmol/mol (5.7%). Adjusted Cox proportional hazards regression models were used to assess the association between RDW quartiles and elevation of HbA1c/glucose. The multiple-adjusted hazard ratios (95% confidence interval) of HbA1c elevation for increased quartiles of RDW were 1.00 (reference), 1.08 (0.89, 1.30), 1.28 (1.07, 1.54), and 1.54 (1.29, 1.85) (P for trend<0.0001). However, no significant association was observed between RDW and blood glucose (fasting and postprandial). Elevated RDW is independently related to future HbA1c elevation, but not to glucose elevation. This suggests that RDW may associate with HbA1c through a non-glycemic way, which should be taken into consideration when using HbA1c as a diagnostic criterion of prediabetes or diabetes. Copyright © 2017 Elsevier Inc. All rights reserved.

Elevated carbon dioxide and ozone alter productivity and ecosystem carbon content in northern temperate forests.

Science.gov (United States)

Talhelm, Alan F; Pregitzer, Kurt S; Kubiske, Mark E; Zak, Donald R; Campany, Courtney E; Burton, Andrew J; Dickson, Richard E; Hendrey, George R; Isebrands, J G; Lewin, Keith F; Nagy, John; Karnosky, David F

2014-08-01

Three young northern temperate forest communities in the north-central United States were exposed to factorial combinations of elevated carbon dioxide (CO2 ) and tropospheric ozone (O3 ) for 11 years. Here, we report results from an extensive sampling of plant biomass and soil conducted at the conclusion of the experiment that enabled us to estimate ecosystem carbon (C) content and cumulative net primary productivity (NPP). Elevated CO2 enhanced ecosystem C content by 11%, whereas elevated O3 decreased ecosystem C content by 9%. There was little variation in treatment effects on C content across communities and no meaningful interactions between CO2 and O3 . Treatment effects on ecosystem C content resulted primarily from changes in the near-surface mineral soil and tree C, particularly differences in woody tissues. Excluding the mineral soil, cumulative NPP was a strong predictor of ecosystem C content (r(2) = 0.96). Elevated CO2 enhanced cumulative NPP by 39%, a consequence of a 28% increase in canopy nitrogen (N) content (g N m(-2) ) and a 28% increase in N productivity (NPP/canopy N). In contrast, elevated O3 lowered NPP by 10% because of a 21% decrease in canopy N, but did not impact N productivity. Consequently, as the marginal impact of canopy N on NPP (∆NPP/∆N) decreased through time with further canopy development, the O3 effect on NPP dissipated. Within the mineral soil, there was less C in the top 0.1 m of soil under elevated O3 and less soil C from 0.1 to 0.2 m in depth under elevated CO2 . Overall, these results suggest that elevated CO2 may create a sustained increase in NPP, whereas the long-term effect of elevated O3 on NPP will be smaller than expected. However, changes in soil C are not well-understood and limit our ability to predict changes in ecosystem C content. © 2014 The Authors Global Change Biology Published by John Wiley & Sons Ltd.

Elevated carbon dioxide and ozone alter productivity and ecosystem carbon content in northern temperate forests

Science.gov (United States)

Talhelm, Alan F; Pregitzer, Kurt S; Kubiske, Mark E; Zak, Donald R; Campany, Courtney E; Burton, Andrew J; Dickson, Richard E; Hendrey, George R; Isebrands, J G; Lewin, Keith F; Nagy, John; Karnosky, David F

2014-01-01

Three young northern temperate forest communities in the north-central United States were exposed to factorial combinations of elevated carbon dioxide (CO2) and tropospheric ozone (O3) for 11 years. Here, we report results from an extensive sampling of plant biomass and soil conducted at the conclusion of the experiment that enabled us to estimate ecosystem carbon (C) content and cumulative net primary productivity (NPP). Elevated CO2 enhanced ecosystem C content by 11%, whereas elevated O3 decreased ecosystem C content by 9%. There was little variation in treatment effects on C content across communities and no meaningful interactions between CO2 and O3. Treatment effects on ecosystem C content resulted primarily from changes in the near-surface mineral soil and tree C, particularly differences in woody tissues. Excluding the mineral soil, cumulative NPP was a strong predictor of ecosystem C content (r2 = 0.96). Elevated CO2 enhanced cumulative NPP by 39%, a consequence of a 28% increase in canopy nitrogen (N) content (g N m−2) and a 28% increase in N productivity (NPP/canopy N). In contrast, elevated O3 lowered NPP by 10% because of a 21% decrease in canopy N, but did not impact N productivity. Consequently, as the marginal impact of canopy N on NPP (ΔNPP/ΔN) decreased through time with further canopy development, the O3 effect on NPP dissipated. Within the mineral soil, there was less C in the top 0.1 m of soil under elevated O3 and less soil C from 0.1 to 0.2 m in depth under elevated CO2. Overall, these results suggest that elevated CO2 may create a sustained increase in NPP, whereas the long-term effect of elevated O3 on NPP will be smaller than expected. However, changes in soil C are not well-understood and limit our ability to predict changes in ecosystem C content. PMID:24604779

Elevated CO2 Reduced Floret Death in Wheat Under Warmer Average Temperatures and Terminal Drought

Science.gov (United States)

Dias de Oliveira, Eduardo; Palta, Jairo A.; Bramley, Helen; Stefanova, Katia; Siddique, Kadambot H. M.

2015-01-01

Elevated CO2 often increases grain yield in wheat by enhancing grain number per ear, which can result from an increase in the potential number of florets or a reduction in the death of developed florets. The hypotheses that elevated CO2 reduces floret death rather than increases floret development, and that grain size in a genotype with more grains per unit area is limited by the rate of grain filling, were tested in a pair of sister lines contrasting in tillering capacity (restricted- vs. free-tillering). The hypotheses were tested under elevated CO2, combined with +3°C above ambient temperature and terminal drought, using specialized field tunnel houses. Elevated CO2 increased net leaf photosynthetic rates and likely the availability of carbon assimilates, which significantly reduced the rates of floret death and increased the potential number of grains at anthesis in both sister lines by an average of 42%. The restricted-tillering line had faster grain-filling rates than the free-tillering line because the free-tillering line had more grains to fill. Furthermore, grain-filling rates were faster under elevated CO2 and +3°C above ambient. Terminal drought reduced grain yield in both lines by 19%. Elevated CO2 alone increased the potential number of grains, but a trade-off in yield components limited grain yield in the free-tillering line. This emphasizes the need for breeding cultivars with a greater potential number of florets, since this was not affected by the predicted future climate variables. PMID:26635837

Elevated CO2 reduced floret death in wheat under warmer average temperatures and terminal drought.

Directory of Open Access Journals (Sweden)

Eduardo eDias de Oliveira

2015-11-01

Full Text Available Elevated CO2 often increases grain yield in wheat by enhancing grain number per ear, which can result from an increase in the potential number of florets or a reduction in the death of developed florets. The hypotheses that elevated CO2 reduces floret death rather than increases floret development, and that grain size in a genotype with more grains per unit area is limited by the rate of grain filling, were tested in a pair of sister lines contrasting in tillering capacity (restricted- vs free-tillering. The hypotheses were tested under elevated CO2, combined with +3 C above ambient temperature and terminal drought, using specialized field tunnel houses. Elevated CO2 increased net leaf photosynthetic rates and likely the availability of carbon assimilates, which significantly reduced the rates of floret death and increased the potential number of grains at anthesis in both sister lines by an average of 42%. The restricted-tillering line had faster grain-filling rates than the free-tillering line because the free-tillering line had more grains to fill. Furthermore, grain-filling rates were faster under elevated CO2 and +3 C above ambient. Terminal drought reduced grain yield in both lines by 19%. Elevated CO2 alone increased the potential number of grains, but a trade-off in yield components limited grain yield in the free-tillering line. This emphasizes the need for breeding cultivars with a greater potential number of florets, since this was not affected by the predicted future climate variables.

Haemodynamic patterns in ST-elevation myocardial infarction : incidence and correlates of elevated filling pressures

NARCIS (Netherlands)

Bergstra, A.; Svilaas, T.; van Veldhuisen, D. J.; van den Heuvel, A. F. M.; van der Horst, I. C. C.; Zijlstra, F.

Objectives. We sought to study the incidence and clinical correlates of elevated filling pressures in ST-elevation myocardial infarction (STEMI) patients, without physical signs of heart failure and treated with primary coronary angioplasty. Background. Haemodynamic data, as measured with a

ARM Support for the Plains Elevated Convection at Night (AS-PECAN) Field Campaign Report

Energy Technology Data Exchange (ETDEWEB)

Turner, D. D. [National Oceanic and Atmospheric Administration (NOAA), Silver Spring, MD (United States); Geerts, B. [Univ. of Wyoming, Laramie, WY (United States)

2016-04-01

The Plains Elevated Convection at Night (PECAN) field campaign was a large multi-agency/multi-institutional experiment that targeted nighttime convection events in the central plains of the United States in order to better understand a range of processes that lead to the initiation and upscale growth of deep convection. Both weather and climate models struggle to properly represent the timing and intensity of precipitation in the central United States in their simulations. These models must be able to represent the interactions between the nocturnal stable boundary layer (SBL), the nocturnal low-level jet (LLJ), and a reservoir of convectively available potential energy (CAPE) that frequently exists above the SBL. Furthermore, a large fraction of the nocturnal precipitation is due to the organization of mesoscale convective systems (MCSs). In particular, there were four research foci for the PECAN campaign: •The initiation of elevated nocturnal convection focus seeks to elucidate the mesoscaleenvironmental characteristics and processes that lead to convection initiation (CI) and provide baseline data on the early evolution of mesoscale convective clusters. •The dynamics and internal structure and microphysics of nocturnal MCSs focus will investigatethe transition from surface-based to elevated storm structure, the interaction of cold pools generated by MCSs with the nocturnal stable boundary layer, and how the organization and evolution of elevated convection is influenced by the SBL and the vertical profile of wind and stability above the LLJ. •The bores and wave-like disturbances focus seeks to advance knowledge of the initiation of boredisturbances by convection, how the vertical profile of stability and winds modulate bore structure, the role of these disturbances in the initiation, maintenance, and organization of deep convection, and their impact on the LLJ and SBL. •The LLJ focus seeks to understand the processes that influence the spatial and

Radiation-use of a forest exposed to elevated concentrations of atmospheric carbon dioxide

International Nuclear Information System (INIS)

DeLucia, E. H.; George, K.; Hamilton, J. G.

2002-01-01

Radiation-use efficiency of growth (defined as biomass accumulation per unit of absorbed photosynthetically active radiation) of loblobby pine forest plots exposed to ambient or elevated atmospheric carbon dioxide concentration was compared. Biomass accumulation of the dominant loblobby pines was calculated from monthly measurements of tree growth and site-specific allometric measurements. Leaf area index was estimated by optical, allometric and interfall methods, depending on species. Results showed that depending on tree height, elevated carbon dioxide did not alter the above-ground biomass allocation in loblobby pine. Leaf area index estimates by the different methods were found to vary significantly, but elevated carbon dioxide had only a slight effect on leaf area index in the first three years of this study. The 27 per cent increase in radiation-use efficiency of growth in response to carbon dioxide enrichment is believed to have been caused primarily by the stimulation of biomass increment. It was concluded that long-term increases in atmospheric carbon dioxide concentration can increase the radiation-use efficiency of growth in closed canopy forests, but the magnitude and duration of this increase in uncertain. 57 refs., 2 tabs., 3 figs

Phenylephrine-induced elevations in arterial blood pressure are attenuated in heat-stressed humans

Science.gov (United States)

Cui, Jian; Wilson, Thad E.; Crandall, Craig G.

2002-01-01

To test the hypothesis that phenylephrine-induced elevations in blood pressure are attenuated in heat-stressed humans, blood pressure was elevated via steady-state infusion of three doses of phenylephrine HCl in 10 healthy subjects in both normothermic and heat stress conditions. Whole body heating significantly increased sublingual temperature by 0.5 degrees C, muscle sympathetic nerve activity (MSNA), heart rate, and cardiac output and decreased total peripheral vascular resistance (TPR; all P blood pressure (MAP; P > 0.05). At the highest dose of phenylephrine, the increase in MAP and TPR from predrug baselines was significantly attenuated during the heat stress [DeltaMAP 8.4 +/- 1.2 mmHg; DeltaTPR 0.96 +/- 0.85 peripheral resistance units (PRU)] compared with normothermia (DeltaMAP 15.4 +/- 1.4 mmHg, DeltaTPR 7.13 +/- 1.18 PRU; all P blood pressure, as well as the slope of the relationship between heart rate and systolic blood pressure, respectively, was similar between thermal conditions (each P > 0.05). These data suggest that phenylephrine-induced elevations in MAP are attenuated in heat-stressed humans without affecting baroreflex control of MSNA or heart rate.

Global variation in elevational diversity patterns

Science.gov (United States)

Qinfeng Guo; Douglas A. Kelt; Zhongyu Sun; Hongxiao Liu; Liangjun Hu; Hai Ren; Jun We

2013-01-01

While horizontal gradients of biodiversity have been examined extensively in the past, vertical diversity gradients (elevation, water depth) are attracting increasing attention. We compiled data from 443 elevational gradients involving diverse organisms worldwide to investigate how elevational diversity patterns may vary between the Northern and Southern hemispheres...

21 CFR 890.3930 - Wheelchair elevator.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Wheelchair elevator. 890.3930 Section 890.3930 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... elevator. (a) Identification. A wheelchair elevator is a motorized lift device intended for medical...

Ice condenser containment analysis with the GOTHIC code

International Nuclear Information System (INIS)

Yadon, T.P.

1996-01-01

Analytical methodologies have recently been developed by Duke Power Company (Duke) to calculate the thermodynamic response of the ice condenser containment buildings at the McGuire and Catawba Nuclear Stations to high-energy line breaks. The GOTHIC computer code (Version 4.0) was utilized for these analyses. In the ice condenser containment design, a large mass of ice stored within the containment building is used to absorb the energy released from high-energy line breaks, thereby limiting the peak pressure and temperature in the containment building to within design limits. The McGuire and Catawba Nuclear Stations (both two-unit, 3411 MWth four-loop Westinghouse plants) are of the ice condenser containment design

Evaluation Of Liner Back-pressure Due To Concrete Pore Pressure At Elevated Temperatures

International Nuclear Information System (INIS)

James, R.J.; Rashid, Y.R.; Liu, A.S.; Gou, B.

2006-01-01

GE's latest evolution of the boiling water reactor, the ESBWR, has innovative passive design features that reduce the number and complexity of active systems, which in turn provide economic advantages while also increasing safety. These passive systems used for emergency cooling also mean that the primary containment system will experience elevated temperatures with longer durations than conventional plants in the event of design basis accidents. During a Loss of Coolant Accident (LOCA), the drywell in the primary containment structure for the ESBWR will be exposed to saturated steam conditions for up to 72 hours following the accident. A containment spray system may be activated that sprays the drywell area with water to condense the steam as part of the recovery operations. The liner back-pressure will build up gradually over the 72 hours as the concrete temperatures increase, and a sudden cool down could cause excessive differential pressure on the liner to develop. For this analysis, it is assumed that the containment spray is activated at the end of the 72-hour period. A back-pressure, acting between the liner and the concrete wall of the containment, can occur as a result of elevated temperatures in the concrete causing steam and saturated vapor pressures to develop from the free water remaining in the pores of the concrete. Additional pore pressure also develops under the elevated temperatures from the non-condensable gases trapped in the concrete pores during the concrete curing process. Any buildup of this pore pressure next to the liner, in excess of the drywell internal pressure, will act to push the liner away from the concrete with a potential for tearing at the liner anchorages. This paper describes the methods and analyses used to quantify this liner back-pressure so that appropriate measures are included in the design of the liner and anchorage system. A pore pressure model is developed that calculates the pressure distribution across the concrete

Carbonate deposition, Pyramid Lake subbasin, Nevada: 1. Sequence of formation and elevational distribution of carbonate deposits (Tufas)

Science.gov (United States)

Benson, L.

1994-01-01

During the late Quarternary, the elevation of terrace cutting and carbonate deposition in the Pyramid Lake subbasin were controlled by constancy of lake level imposed by spill to adjoining subbasins. Sill elevations are 1177-1183 m (Mud Lake Slough Sill), 1207 m (Emerson Pass Sill), and 1265 m (Darwin Pass Sill). Carbonate deposition was favored by: (1) hydrologic closure, (2) proximity to a source of calcium, (3) elevated water temperature, and (4) a solid substrate. The thickness and aspect of tufa are a function oflake-level dynamics. Relatively thin sheets and pendant sheets were deposited during a rising or falling lake. The upper parts of thick reef-form tufas have a horizontal aspect and were deposited in a lake which was stabilized by spill to the Carson Desert subbasin. The lower parts of the reef-form tufas are thinner and their outer surface has a vertical aspect, indicating that the lower part formed in a receding lake. The thickest and most complete sequences of tufa are mounds that border the Pyramid Lake shore. The tops of the tallest mounds reach the elevation of the Darwin Pass Sill and many mounds have been eroded to the elevations of the Mud Lake Slough Sill of the Emerson Pass Sill. The sequence of tufa formation (from oldest to youngest) displayed in these mounds is: (1) a beachrock containing carbonate-cemented volcanic cobbles, (2) broken and eroded old spheroids that contain thinolitic tufa and an outer rind of dense laminated tufa, (3) large cylindrical (tubular) tufas capped by (4) coatings of old dense tufas, and (5) several generations of old branching tufa commonly associated with thin, platy tufas and coatings of thinolitic tufa, (6) young spheroids that contain poorly oriented young thinolitic tufa in the center and several generations of radially oriented young thinolitic tufas near the outer edge, (7) a transitional thinolite-to-branching tufa, (8) two or more layers of young branching tufa, (9) a 0.5-cm-thick layer of fine

Skeletal Fluorosis Due To Inhalation Abuse of a Difluoroethane-Containing Computer Cleaner.

Science.gov (United States)

Tucci, Joseph R; Whitford, Gary M; McAlister, William H; Novack, Deborah V; Mumm, Steven; Keaveny, Tony M; Whyte, Michael P

2017-01-01

Skeletal fluorosis (SF) is endemic in many countries and millions of people are affected worldwide, whereas in the United States SF is rare with occasional descriptions of unique cases. We report a 28-year-old American man who was healthy until 2 years earlier when he gradually experienced difficulty walking and an abnormal gait, left hip pain, loss of mobility in his right wrist and forearm, and progressive deformities including enlargement of the digits of both hands. Dual-energy X-ray absorptiometry (DXA) of his lumbar spine, femoral neck, total hip, and the one-third forearm revealed bone mineral density (BMD) Z-scores of +6.2, +4.8, +3.0, and -0.2, respectively. Serum, urine, and bone fluoride levels were all elevated and ultimately explained by chronic sniffing abuse of a computer cleaner containing 1,1-difluoroethane. Our findings reflect SF due to the unusual cause of inhalation abuse of difluoroethane. Because this practice seems widespread, particularly in the young, there may be many more such cases. © 2016 American Society for Bone and Mineral Research. © 2016 American Society for Bone and Mineral Research.

40 CFR 264.552 - Corrective Action Management Units (CAMU).

Science.gov (United States)

2010-07-01

..., tanks, or other non-land-based units found above ground, unless the wastes are first placed in the tanks, containers or non-land-based units as part of cleanup, or the containers or tanks are excavated during the... drainage and minimize erosion or abrasion of the cover; (4) Accommodate settling and subsidence so that the...

Shuttle Kit Freezer Refrigeration Unit Conceptual Design

Science.gov (United States)

Copeland, R. J.

1975-01-01

The refrigerated food/medical sample storage compartment as a kit to the space shuttle orbiter is examined. To maintain the -10 F in the freezer kit, an active refrigeration unit is required, and an air cooled Stirling Cycle refrigerator was selected. The freezer kit contains two subsystems, the refrigeration unit, and the storage volume. The freezer must provide two basic capabilities in one unit. One requirement is to store 215 lbs of food which is consumed in a 30-day period by 7 people. The other requirement is to store 128.3 lbs of medical samples consisting of both urine and feces. The unit can be mounted on the lower deck of the shuttle cabin, and will occupy four standard payload module compartments on the forward bulkhead. The freezer contains four storage compartments.

Soil Nematodes and Their Prokaryotic Prey Along an Elevation Gradient in The Mojave Desert (Death Valley National Park, California, USA

Directory of Open Access Journals (Sweden)

Alyxandra Pikus

2012-10-01

Full Text Available We characterized soil communities in the Mojave Desert across an elevation gradient. Our goal was to test the hypothesis that as soil quality improved with increasing elevation (due to increased productivity, the diversity of soil prokaryotes and nematodes would also increase. Soil organic matter and soil moisture content increased with elevation as predicted. Soil salinity did not correlate to elevation, but was highest at a mid-gradient, alluvial site. Soil nematode density, community trophic structure, and diversity did not show patterns related to elevation. Similar results were obtained for diversity of bacteria and archaea. Relationships between soil properties, nematode communities, and prokaryotic diversity were site-specific. For example, at the lowest elevation site, nematode communities contained a high proportion of fungal-feeding species and diversity of bacteria was lowest. At a high-salinity site, nematode density was highest, and overall, nematode density showed an unexpected, positive correlation to salinity. At the highest elevation site, nematode density and species richness were attenuated, despite relatively high moisture and organic matter content for the soils. Our results support emerging evidence for the lack of a relationship between productivity and the diversity of soil nematodes and prokaryotes.

An Automatic System for Elevator Monitoring

OpenAIRE

Md. Haidar Sharif; Ibrahim Furkan Ince

2015-01-01

An elevator is a conveyor device or transport equipment that moves people or goods between floors or levels or decks of a building, vessel, or other structures. It has become a part and parcel of modern life in developed countries. The number of floors in high buildings, skyscrapers, and towers generate the usage of elevators. If it is simply assumed that each floor has at least two elevators in a thirty-floor building, people call the elevators in each floor even they are already occupied in...

A genome-wide assessment of stages of elevational parapatry in Bornean passerine birds reveals no introgression: implications for processes and patterns of speciation

Directory of Open Access Journals (Sweden)

Robert G. Moyle

2017-05-01

Full Text Available Topographically complex regions often contain the close juxtaposition of closely related species along elevational gradients. The evolutionary causes of these elevational replacements, and thus the origin and maintenance of a large portion of species diversity along elevational gradients, are usually unclear because ecological differentiation along a gradient or secondary contact following allopatric diversification can produce the same pattern. We used reduced representation genomic sequencing to assess genetic relationships and gene flow between three parapatric pairs of closely related songbird taxa (Arachnothera spiderhunters, Chloropsis leafbirds, and Enicurus forktails along an elevational gradient in Borneo. Each taxon pair presents a different elevational range distribution across the island, yet results were uniform: little or no gene flow was detected in any pairwise comparisons. These results are congruent with an allopatric “species-pump” model for generation of species diversity and elevational parapatry of congeners on Borneo, rather than in situ generation of species by “ecological speciation” along an elevational gradient.

Modeling containment of large wildfires using generalized linear mixed-model analysis

Science.gov (United States)

Mark Finney; Isaac C. Grenfell; Charles W. McHugh

2009-01-01

Billions of dollars are spent annually in the United States to contain large wildland fires, but the factors contributing to suppression success remain poorly understood. We used a regression model (generalized linear mixed-model) to model containment probability of individual fires, assuming that containment was a repeated-measures problem (fixed effect) and...

Sargent and Lundy containment tests revisited

International Nuclear Information System (INIS)

Henry, Robert E.; Hammersley, Robert J.

2005-01-01

The pressurization experiments performed in the intermediate scale Sargent and Lundy containment test facility provide numerous insights into the dominant heat and mass transfer processes under design basis accident conditions similar to a large break Loss of Coolant Accident (LOCA). These experiments were the first integral tests to examine the containment response to a dynamic blowdown from the Reactor Coolant System (RCS). Measurements included the blowdown rate of the simulated Reactor Pressure Vessel (RPV), the pressure in containment as well as the containment temperatures in the top and bottom of the containment vessel. Furthermore, various experiments were performed with the blowdown location changed from the vessel bottom to the lower third of the vessel, the upper third of the vessel and near the top of the RPV to examine the influence of different types of break elevations, i.e. different characterizations of the exhausting steam-water mixture. Perhaps the most insightful set of measurements from these experiments were those that varied the cold water mass initially resident in the bottom of the simulated containment vessel. The role of this water as a function of its initial mass and the break location showed substantial influence of this water if the blowdown location provided sufficient energy to disperse this cold water into the containment building atmosphere. This is demonstrated in Figure 1 taken from Kolflat, 1960. All of these are relevant to an understanding of the dominant physical processes for this type of postulated accident condition. As such, it is important that all of these insights are retained and used in models for the containment building thermal-hydraulic response under accident conditions. Reference: Kolflat, A., 1960, 'Resulting of 1959 Nuclear Power Plant Containment Test', Sargent and Lundy Report SL-1800; Kolflat, A. and Chittenden, W. A., 1957, 'A New Approach to the Design of Containment Shells for Atomic Power Plants

The effect of oral contraception on cardiometabolic risk factors in women with elevated androgen levels.

Science.gov (United States)

Krysiak, Robert; Gilowska, Małgorzata; Okopień, Bogusław

2017-02-01

In unselected reproductive-aged women, use of combined estrogen-progestin oral contraceptive pills has been linked with an increased risk of vascular disease. The aim of this study was to investigate the effect of oral contraception on cardiometabolic risk factors in a population of women with hyperandrogenism. The study included 16 untreated women with elevated testosterone levels and 15 matched healthy women who were then treated with oral contraceptive pills containing ethinyl estradiol (30μg) and drospirenone (3mg). Plasma lipids, glucose homeostasis markers, circulating levels of androgens, uric acid, high-sensitivity C-reactive protein (hsCRP), fibrinogen and homocysteine, as well as urinary albumin-to-creatinine ratio (UACR) were assessed at baseline and after 12 weeks of treatment. Compared to healthy women, women with elevated androgen levels showed increased plasma levels of hsCRP, fibrinogen and homocysteine, as well as a higher value of UACR. Oral contraception reduced androgen levels only in hyperandrogenic women. In healthy women, ethinyl estradiol plus drospirenone increased plasma levels of insulin, hsCRP, fibrinogen and homocysteine, while in women with elevated androgen levels their effect was limited only to a small increase in hsCRP. Our results suggest that a deteriorating effect of oral contraceptive pills containing ethinyl estradiol and drospirenone in hyperandrogenic women is weaker than in healthy young women and that ethinyl estradiol/drospirenone combination therapy may be safely used in the former group of patients. Copyright © 2016. Published by Elsevier Urban & Partner Sp. z o.o.

Dynamic multibody modeling for tethered space elevators

Science.gov (United States)

Williams, Paul

2009-08-01

This paper presents a fundamental modeling strategy for dealing with powered and propelled bodies moving along space tethers. The tether is divided into a large number of discrete masses, which are connected by viscoelastic springs. The tether is subject to the full range of forces expected in Earth orbit in a relatively simple manner. Two different models of the elevator dynamics are presented. In order to capture the effect of the elevator moving along the tether, the elevator dynamics are included as a separate body in both models. One model treats the elevator's motion dynamically, where propulsive and friction forces are applied to the elevator body. The second model treats the elevator's motion kinematically, where the distance along the tether is determined by adjusting the lengths of tether on either side of the elevator. The tether model is used to determine optimal configurations for the space elevator. A modal analysis of two different configurations is presented which show that the fundamental mode of oscillation is a pendular one around the anchor point with a period on the order of 160 h for the in-plane motion, and 24 h for the out-of-plane motion. Numerical simulation results of the effects of the elevator moving along the cable are presented for different travel velocities and different elevator masses.

Comparing non-invasive scapular tracking methods across elevation angles, planes of elevation and humeral axial rotations.

Science.gov (United States)

Grewal, T-J; Cudlip, A C; Dickerson, C R

2017-12-01

Altered scapular motions premeditate shoulder impingement and other musculoskeletal disorders. Divergent experimental conditions in previous research precludes rigorous comparisons of non-invasive scapular tracking techniques. This study evaluated scapular orientation measurement methods across an expanded range of humeral postures. Scapular medial/lateral rotation, anterior/posterior tilt and protraction/retraction was measured using an acromion marker cluster (AMC), a scapular locator, and a reference stylus. Motion was captured using reflective markers on the upper body, as well as on the AMC, locator and stylus. A combination of 5 arm elevation angles, 3 arm elevation planes and 3 arm axial rotations was examined. Measurement method interacted with elevation angle and plane of elevation for all three scapular orientation directions (p planes and axial rotations. The AMC underestimated lateral rotation, with the largest difference of ∼2° at 0° elevation. Both the locator and AMC overestimated posterior tilt at high arm elevation by up to 7.4°. Misestimations from using the locator could be enough to potentially obscure meaningful differences in scapular rotations. Copyright © 2017 Elsevier Ltd. All rights reserved.

The surface elevation table and marker horizon technique: A protocol for monitoring wetland elevation dynamics

Science.gov (United States)

James C. Lynch,; Phillippe Hensel,; Cahoon, Donald R.

2015-01-01

The National Park Service, in response to the growing evidence and awareness of the effects of climate change on federal lands, determined that monitoring wetland elevation change is a top priority in North Atlantic Coastal parks (Stevens et al, 2010). As a result, the NPS Northeast Coastal and Barrier Network (NCBN) in collaboration with colleagues from the U.S. Geological Survey (USGS) and The National Oceanic and Atmospheric Administration (NOAA) have developed a protocol for monitoring wetland elevation change and other processes important for determining the viability of wetland communities. Although focused on North Atlantic Coastal parks, this document is applicable to all coastal and inland wetland regions. Wetlands exist within a narrow range of elevation which is influenced by local hydrologic conditions. For coastal wetlands in particular, local hydrologic conditions may be changing as sea levels continue to rise. As sea level rises, coastal wetland systems may respond by building elevation to maintain favorable hydrologic conditions for their survival. This protocol provides the reader with instructions and guidelines on designing a monitoring plan or study to: A) Quantify elevation change in wetlands with the Surface Elevation Table (SET). B) Understand the processes that influence elevation change, including vertical accretion (SET and Marker Horizon methods). C) Survey the wetland surface and SET mark to a common reference datum to allow for comparing sample stations to each other and to local tidal datums. D) Survey the SET mark to monitor its relative stability. This document is divided into two parts; the main body that presents an overview of all aspects of monitoring wetland elevation dynamics, and a collection of Standard Operating Procedures (SOP) that describes in detail how to perform or execute each step of the methodology. Detailed instruction on the installation, data collection, data management and analysis are provided in this report

Post-Closure Inspection Report for Corrective Action Unit 90: Area 2 Bitcutter Containment, Nevada Test Site, Nevada

International Nuclear Information System (INIS)

NSTec Environmental Restoration

2008-01-01

Corrective Action Unit (CAU) 90, Area 2 Bitcutter Containment, is identified in the Federal Facility Agreement and Consent Order of 1996, as amended February 2008. The post-closure requirements for CAU 90 are described in Section VII.B.8.b of the Nevada Test Site Resource Conservation and Recovery Act Permit for a Hazardous Waste Management Facility Number NEV HW0021, dated November 2005. Post-closure activities consist of the following: (1) Semiannual inspections of the site using inspection checklists; (2) Photographic documentation; (3) Field note documentation; and (4) Preparation and submittal of an annual Post-Closure Inspection Report. This annual report covers the period of July 2007 to June 2008 and consists of a summary of the results of the inspections, copies of the inspection checklists and field notes, maintenance and repair records (if any), photographs, and conclusions and recommendations. The inspection checklists are provided in Appendix A, a copy of the field notes is provided in Appendix B, and copies of photographs taken during the inspections are provided in Appendix C

EnviroAtlas - NHDPlus V2 Hydrologic Unit Boundaries Web Service - Conterminous United States

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas web service contains layers depicting hydrologic unit boundary layers and labels for the Subregion level (4-digit HUCs), Subbasin level (8-digit...

Gust alleviation for a STOL transport by using elevator, spoilers, and flaps

Science.gov (United States)

Lallman, F. J.

1974-01-01

Control laws were developed to investigate methods of alleviating the response of a STOL transport to gusty air. The transport considered in the study had triple-slotted, externally blown jet flaps and a large T-tail. The control devices used were the elevator, spoilers, and flaps. A hybrid computing system was used to simulate linearized longitudinal dynamics of the aircraft and to implement a conjugate gradient optimal search algorithm. The aircraft was simulated in the low-speed approach condition only. Feedback control matrices were found which minimized the average of a quadratic functional involving passenger compartment accelerations, pitch angle and rate, flight path angle and speed variations. The optimization was performed for artificially designed gust inputs in the form of predetermined rectangular waveforms. Results were obtained for elevator, spoilers, and flaps acting singly and in combination. Additional results were obtained for unit sinusoidal gust inputs by using the gain matrices computed for the artificial test gusts. Various sensor configurations were also investigated.

Comparison of AltiKa and CryoSat-2 Elevation and Elevation Rates over the Amundsen Sea Sector

Science.gov (United States)

Otosaka, I.; Shepherd, A.; Hogg, A.

2017-12-01

Altimeters have been successfully used for more than two decades to observe changes in the ice sheet surface and to estimate the contribution of ice sheets to sea level rise. The Satellite for Argos and AltiKa (SARAL) was launched in February 2013 as a joint mission between the French space agency (CNES) and the Indian Space Research Organisation (ISRO). While the altimeters previously launched into space are operating at Ku-band (13.6 GHz), the altimeter on board SARAL, AltiKa, is the first instrument to operate at Ka-band (36.8 GHz). The higher frequency of AltiKa is expected to lead to reduced penetration of the radar signal into the snowpack, compared to Ku-band. A comparison of ice sheet elevation measurements recorded at the two frequencies may therefore provide useful information on surface and its scattering properties. In this study, we compare elevation and elevation rates recorded by AltiKa and CryoSat-2 between March 2013 and April 2017 over the Amundsen Sea Sector (ASS), one of the most rapidly changing sectors of West Antarctica. Elevation and elevation rates are computed within 5 km grid cells using a plane fit method, taking into account the contributions of topography and fluctuations in elevation and backscatter. The drifting orbit and imaging modes of CryoSat-2 result in 78,7 % sampling of the study area, whereas AltiKa samples 39,7 % due to its sparser orbit pattern and due to loss of signal in steeply sloping coastal margins. Over the study period, the root mean square difference between elevation and elevation change recorded at Ka-band and Ku-band were 40.3 m and 0.54 m/yr, respectively. While the broad spatial pattern of elevation change is well resolved by both satellites, data gaps along the Getz coastline may be partly responsible for the lower elevation change rate observed at Ka-band. We also compared CryoSat-2 and AltiKa to coincident airborne data from NASA's Operation IceBridge (OIB). The mean difference of elevation rate between

Safety verification of refrigeration containers using barrier certificates

DEFF Research Database (Denmark)

Christensen, Rasmus Lundgaard; Wisniewski, Rafal; Sørensen, Kresten Kjær

2016-01-01

Refrigeration containers make up a large portion of todays global trade, carrying anything from electronics to fresh fruit and vegetables. The containers are transported through varying surrounding temperatures which speeds up the wear and tear of the mechanical parts of the system. It is therefore...... of interest to produce a fault detection scheme, that allows for varying ambient temperature, varying handling standards, varying mechanical state, and accurately predicts if the system is trending towards failure. Lodam Electronics A/S develops control units for refrigeration containers, and are interested...

Thin type inverter for machine-room-less elevator; Machine roomless elevator yo usugata inverter

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-01-10

In the elevator industry, a machine-room-less elevator, which does not necessitate a machine room usually installed on the roof, has come into the spotlight in the domain of low and intermediate speed elevators. The lack of a machine room, however, will necessarily limit the space for the installation of the traction motor and control panel. Fuji Electric Co., Ltd., in order to properly cope with the situation, has developed in cooperation with Fujitec Co., Ltd., a very thin type inverter installable on an elevator hall floor. The inverter, based on Fuji Electric's high-performance vector control inverter FRENIC5000VG5, is as thin as 100mm, and is available in three series up to 11kW. For the embodiment of such a thin structure, a cooling structure of Fuji Electric's own is employed, and prudence is exercised as required at many locations so that maintainability will not be impaired throughout the very thin control panel design. (translated by NEDO)

E4 - Energy efficient elevators and escalators. Elevators and escalators in Germany from an energy perspective

Energy Technology Data Exchange (ETDEWEB)

Hirzel, Simon; Fleiter, Tobias; Rosende, Daniel

2010-01-31

This report aims to provide a brief introduction to the German elevator and escalator market, and gives an aggregated view of current and future developments focusing on energy consumption and energy-related emissions. This update report of January 2010 is an extended version of a report published in April 2009 before the final results from a monitoring campaign carried out within the project were available. During this campaign, 81 installations (74 elevators and 7 escalators) were monitored in terms of energy consumption. In the first section, the structure of the installed German elevator and escalator capacity is presented. The estimates1 were provided courtesy of the two main associations representing elevators and escalators in Germany: the VDMA (Verband Deutscher Maschinen- und Anlagenbau - German Engineering Federation) and the VFA-Interlift e.V. -Verband fuer Aufzugstechnik (Association for Lift Technology). This section is followed by a short description of the German construction sector and its implications for elevators and escalators. The third section describes German electricity production in terms of its environmental impact with the main focus on the carbon dioxide emissions of the national power plants. Then the energy consumption of elevators and escalators in Germany is analyzed, comparing the results to total energy production in Germany.2 The final section summarizes the different aspects and derives indications about the future development of the total energy consumption of elevators and escalators in Germany. (orig.)

Cold weather effects on Dresden Unit 1

Energy Technology Data Exchange (ETDEWEB)

Anagnostopoulos, H. [Commonwealth Edison Co., Morris, IL (United States)

1995-03-01

Dresden Unit 1 is in the final stages of a decommissioning effort directed at preparing the unit to enter a SAFSTOR status. Following an extended sub-zero cold wave, about 55,000 gallons of water were discovered in the lowest elevation of the spherical reactor enclosure. Cold weather had caused the freezing and breaking of several service water lines that had not been completely isolated. Two days later, at a regularly scheduled decommissioning meeting, the event was communicated to the decommissioning team, who quickly recognized the potential for freezing of a 42 inches diameter Fuel Transfer Tube that connects the sphere to the Spent Fuel Pool. The team directed that the pool gates between the adjacent Spent Fuel Pool and the Fuel Transfer Pool be installed, and a portable source of heat was installed on the Fuel Transfer Tube. It was later determined that, with the fuel pool gates removed, and with a worst case freeze break at the 502 elevation on the Fuel Transfer Tube (in the Sphere), the fuel in the Spent Fuel Pool could be uncovered to a level 3 below the top of active fuel.

Space Elevators Preliminary Architectural View

Science.gov (United States)

Pullum, L.; Swan, P. A.

Space Systems Architecture has been expanded into a process by the US Department of Defense for their large scale systems of systems development programs. This paper uses the steps in the process to establishes a framework for Space Elevator systems to be developed and provides a methodology to manage complexity. This new approach to developing a family of systems is based upon three architectural views: Operational View OV), Systems View (SV), and Technical Standards View (TV). The top level view of the process establishes the stages for the development of the first Space Elevator and is called Architectural View - 1, Overview and Summary. This paper will show the guidelines and steps of the process while focusing upon components of the Space Elevator Preliminary Architecture View. This Preliminary Architecture View is presented as a draft starting point for the Space Elevator Project.

The analysis of access routes to clusters of fuel-containing materials in the room 305/2 of 'Ukryttya' object. Part 3. Research wells at elevations 10-11 m and PRK

International Nuclear Information System (INIS)

Vysotskij, E.D.; Dovyd'kov, A.I.; Dovyd'kov, S.A.; Krasnov, V.A.; Shcherbin, V.N.

2012-01-01

The results of the analysis of research wells parameters, drilled to the room 305/2 area of 'UKRYTTYA' object, which can be used for control systems of nuclear-hazardous accumulations of fuel-containing materials (FCM) in the area, are presented. The Wells, which were drilled from the premises 207/4, 207/5 at elevations 10-11 m, and the inclined wells to the steam distribution corridor are examined. Systematization of main characteristics of these wells carried out. Analysis of neutron flux measurement results, exposure dose rate and temperature in these wells at after-accident period is conducted. The recommendations for research wells exploitation for placement of sensors for FCM nuclear-physical parameters controlling systems are given. The results of analysis allow to determine the most informative places for FCM controlling systems sensors arrangement and to evaluate possible controlled parameters value ranges at these points

Community and ecosystem responses to elevational gradients

DEFF Research Database (Denmark)

Sundqvist, Maja K.; Sanders, Nate; Wardle, David A.

2013-01-01

Community structure and ecosystem processes often vary along elevational gradients. Their responses to elevation are commonly driven by changes in temperature, and many community- and ecosystem-level variables therefore frequently respond similarly to elevation across contrasting gradients...... elevational gradients for understanding community and ecosystem responses to global climate change at much larger spatial and temporal scales than is possible through conventional ecological experiments. However, future studies that integrate elevational gradient approaches with experimental manipulations...... will provide powerful information that can improve predictions of climate change impacts within and across ecosystems....

78 FR 57033 - United States Standards for Condition of Food Containers

Science.gov (United States)

2013-09-17

... renumbered. In subsequent discussions, the commenter requested AMS change ``Enamel cracked in metal container material not affecting usability'' in minor defect 203, Table XII, to ``Enamel breakdown in metal affecting usability'' as the terms ``cracked'' and ``breakdown'' mean the same thing. AMS determined that this had...

Declines in low-elevation subalpine tree populations outpace growth in high-elevation populations with warming

Science.gov (United States)

Conlisk, Erin; Castanha, Cristina; Germino, Matthew J.; Veblen, Thomas T; Smith, Jeremy M.; Kueppers, Lara M.

2017-01-01

Species distribution shifts in response to climate change require that recruitment increase beyond current range boundaries. For trees with long life spans, the importance of climate-sensitive seedling establishment to the pace of range shifts has not been demonstrated quantitatively.Using spatially explicit, stochastic population models combined with data from long-term forest surveys, we explored whether the climate-sensitivity of recruitment observed in climate manipulation experiments was sufficient to alter populations and elevation ranges of two widely distributed, high-elevation North American conifers.Empirically observed, warming-driven declines in recruitment led to rapid modelled population declines at the low-elevation, ‘warm edge’ of subalpine forest and slow emergence of populations beyond the high-elevation, ‘cool edge’. Because population declines in the forest occurred much faster than population emergence in the alpine, we observed range contraction for both species. For Engelmann spruce, this contraction was permanent over the modelled time horizon, even in the presence of increased moisture. For limber pine, lower sensitivity to warming may facilitate persistence at low elevations – especially in the presence of increased moisture – and rapid establishment above tree line, and, ultimately, expansion into the alpine.Synthesis. Assuming 21st century warming and no additional moisture, population dynamics in high-elevation forests led to transient range contractions for limber pine and potentially permanent range contractions for Engelmann spruce. Thus, limitations to seedling recruitment with warming can constrain the pace of subalpine tree range shifts.

Variations in IBD (ACAD8) in children with elevated C4-carnitine detected by tandem mass spectrometry newborn screening

DEFF Research Database (Denmark)

Pedersen, Christina B; Bischoff, Claus; Christensen, Ernst

2006-01-01

or compound heterozygous for variations in the IBD gene have been reported. We present IBD deficiency in an additional four newborns with elevated C(4)-carnitine identified by tandem mass spectrometry (MS/MS) screening in Denmark and the United States. Three showed urinary excretions of isobutyryl...

Structural studies on volatile, air and moisture sensitive liquids at ambient and elevated temperatures using liquid X-ray scattering. The structure of liquid gallium (III) chloride systems

Science.gov (United States)

Ulvenlund, Stefan; Bengtsson, Lars A.

1994-09-01

An X-ray scattering method is presented which provides accurate structural information on air and moisture sensitive liquids at ambient and elevated temperatures using a standard θ-θ X-ray diffractometer. The method utilizes capillary glass tubes as sample containers and requires no corrections for sample container absorption or scattering, as shown by structural studies of well-known systems such as benzene, carbon tetrachloride and antimony trichloride. Artefacts produced by the sample holder are insignificant and very easy to correct for. The major drawback of the method is the long time of experiment, due to the small (compared with the standard set-up) area/volume ratio of the liquid which contributes to the intensity of the scattered radiation. However, the time required is not unduly long except for liquids containing light elements only (very low scattering power) or very heavy ones (high liner absorptivity). Liquid GaCl 3 is shown to have a dimeric structure consisting of edge-sharing GaCl 4 tetrahedra. This structure is analogous to that previously found for GaCl 3 in the gaseous and solid state and for AlCl 3 in the gaseous and liquid state. Concentrated solutions of GaCl 3 in benzene have been shown to comprise monomeric GaCl 3 units with C3v symmetry. However, it is suggested that such units form as a result of a radiolytically induced cleavage of the Ga 2Cl 6 moieties. No GaC correlation is resolved, which is explained by assuming a σ-type complex GaCl 3 and benzene and/or an ill-defined interaction between the GaCl 3 unit and benzene. The former sitution would most probably produce too few GaC correlation to be observable by the present method, whereas the latter situation would produce a very broad GaC correlation difficult to separate from the background. However, the deviation from the D3h symmetry adopted by GaCl 3 in the gas phase indicates a specific interation between GaCl 3 and benzene.

Elevated CO2 enhances biological contributions to elevation change in coastal wetlands by offsetting stressors associated with sea-level rise

Science.gov (United States)

Cherry, J.A.; McKee, K.L.; Grace, J.B.

2009-01-01

1. Sea-level rise, one indirect consequence of increasing atmospheric CO2, poses a major challenge to long-term stability of coastal wetlands. An important question is whether direct effects of elevated CO 2 on the capacity of marsh plants to accrete organic material and to maintain surface elevations outweigh indirect negative effects of stressors associated with sea-level rise (salinity and flooding). 2. In this study, we used a mesocosm approach to examine potential direct and indirect effects of atmospheric CO2 concentration, salinity and flooding on elevation change in a brackish marsh community dominated by a C3 species, Schoenoplectus americanus, and a C4 grass, Spartina patens. This experimental design permitted identification of mechanisms and their role in controlling elevation change, and the development of models that can be tested in the field. 3. To test hypotheses related to CO2 and sea-level rise, we used conventional anova procedures in conjunction with structural equation modelling (SEM). SEM explained 78% of the variability in elevation change and showed the direct, positive effect of S. americanus production on elevation. The SEM indicated that C3 plant response was influenced by interactive effects between CO2 and salinity on plant growth, not a direct CO2 fertilization effect. Elevated CO2 ameliorated negative effects of salinity on S. americanus and enhanced biomass contribution to elevation. 4. The positive relationship between S. americanus production and elevation change can be explained by shoot-base expansion under elevated CO 2 conditions, which led to vertical soil displacement. While the response of this species may differ under other environmental conditions, shoot-base expansion and the general contribution of C3 plant production to elevation change may be an important mechanism contributing to soil expansion and elevation gain in other coastal wetlands. 5. Synthesis. Our results revealed previously unrecognized interactions and

Impact of elevated CO2 and elevated O3 on Beta vulgaris L.: Pigments, metabolites, antioxidants, growth and yield

International Nuclear Information System (INIS)

Kumari, Sumita; Agrawal, Madhoolika; Tiwari, Supriya

2013-01-01

The present study was conducted to assess morphological, biochemical and yield responses of palak (Beta vulgaris L. cv Allgreen) to ambient and elevated levels of CO 2 and O 3 , alone and in combination. As compared to the plants grown in charcoal filtered air (ACO 2 ), growth and yield of the plants increased under elevated CO 2 (ECO 2 ) and decreased under combination of ECO 2 with elevated O 3 (ECO 2 + EO 3 ), ambient O 3 (ACO 2 + AO 3 ) and elevated O 3 (EO 3 ). Lipid peroxidation, ascorbic acid, catalase and glutathione reductase activities enhanced under all treatments and were highest in EO 3. Foliar starch and organic carbon contents increased under ECO 2 and ECO 2 + EO 3 and reduced under EO 3 and ACO 2 + AO 3. Foliar N content declined in all treatments compared to ACO 2 resulting in alteration of C/N ratio. This study concludes that ambient level of CO 2 is not enough to counteract O 3 impact, but elevated CO 2 has potential to counteract the negative effects of future O 3 level. -- Highlights: ► Elevated CO 2 enhanced the growth and yield of palak. ► Ambient and elevated ozone reduced the growth and yield of the test plant. ► Elevated CO 2 reduced negative effects of elevated O 3 by reducing oxidative stress. ► Higher amelioration was recorded at elevated CO 2 + O 3 compared to ambient CO 2 + O 3 . -- Predicted levels of CO 2 have greater ameliorative potential against negative effects of elevated ozone compared to present day CO 2 against ambient ozone

Stability of penicillin G sodium diluted with 0.9% sodium chloride injection or 5% dextrose injection and stored in polyvinyl chloride bag containers and elastomeric pump containers.

Science.gov (United States)

Hossain, Mirza Akram; Friciu, Mihaela; Aubin, Sebastien; Leclair, Grégoire

2014-04-15

The stability of penicillin G sodium solutions stored in polyvinyl chloride (PVC) bags or elastomeric pump containers was studied. Test samples were prepared by diluting powdered penicillin G sodium (10 million units/10-mL vial) to solutions of 2,500 or 50,000 units/mL with 0.9% sodium chloride injection or 5% dextrose injection. The preparations were transferred to 250-mL PVC bags and elastomeric pump containers. All samples were prepared in triplicate and stored at 5°C. Chemical stability was measured by a stability-indicating high-performance liquid chromatographic (HPLC) assay and by pH evaluation. Particulate matter was evaluated according to compendial standards using a light-obscuration particle count test. Preparations were visually examined throughout the study. After 21 days of storage, all test samples remained chemically stable, with an HPLC assay recovery value of more than 90% of the initial value. After 28 days, all samples prepared with either diluent and stored in PVC bags, as well as the samples diluted to 2,500 units/mL with sodium chloride injection and stored in elastomeric pump containers, did not meet the recovery acceptance limit. For all test samples, the mean pH consistently decreased during storage, from about 6.4 to about 5.5. Particle counts remained acceptable throughout the study, and no change in appearance was observed. Penicillin G for injection (2,500 and 50,000 units/mL) diluted in 0.9% sodium chloride injection or 5% dextrose injection and stored at 5°C in PVC containers or elastomeric pump containers was physically and chemically stable for a period of at least 21 days.

Degree of conversion and microhardness of TPO-containing resin-based composites cured by polywave and monowave LED units.

Science.gov (United States)

Santini, Ario; Miletic, Vesna; Swift, Michael D; Bradley, Mark

2012-07-01

To determine the degree of conversion (DC) and Knoop microhardness (KHN) of resin-based composites (RBCs) containing trimethylbenzoyl-diphenylphosphine oxide (TPO) cured by polywave or monowave LED light-curing units (LCUs). Three groups (each n = 5) of Tetric EvoCeram (Ivoclar Vivadent), Vit-l-escence (Ultradent) and Herculite XRV Ultra (Kerr) were prepared in Teflon moulds (5mm in diameter and 2mm thick) and cured with polywave Bluephase(®) G2 (Ivoclar Vivadent), polywave Valo (Ultradent) or monowave Bluephase(®) (Ivoclar Vivadent; control) resulting in 9 groups. DC and KHN were determined using micro-Raman spectroscopy and Knoop microhardness, respectively. High-performance liquid chromatography and nuclear magnetic resonance spectroscopy were used to confirm the presence or absence of TPO in the three uncured materials. Data were statistically analysed using two-way and one-way ANOVA and DC and KHN were correlated using Pearson's correlation (α = 0.05). TPO was confirmed in Tetric EvoCeram and Vit-l-escence but not in Herculite XRV Ultra. All three LCUs produced comparable KHN for Tetric EvoCeram and Herculite XRV Ultra (p > 0.05). Both polywave LCUs resulted in significantly higher KHN for Vit-l-escence and higher DC in Tetric EvoCeram and Vit-l-escence than the monowave Bluephase(®) (p Conversely, Bluephase(®) showed higher DC than the two polywave LCUs in Herculite XRV Ultra (p conversion and KHN in the two TPO-containing RBCs, but not in Herculite XRV Ultra. DC and KHN were linearly correlated in all three RBCs. Vit-l-escence showed the highest DC and KHN of the three materials tested. The use of polywave LEDs significantly improves both the DC and KHN of materials which contain TPO. This should be taken into account when curing bleached shades of RBCs even if the manufacturers do not indicate the presence of TPO in their materials. Copyright © 2012 Elsevier Ltd. All rights reserved.

Energy-containing beverages: reproductive hormones and ovarian function in the BioCycle Study.

Science.gov (United States)

Schliep, Karen C; Schisterman, Enrique F; Mumford, Sunni L; Pollack, Anna Z; Perkins, Neil J; Ye, Aijun; Zhang, Cuilin J; Stanford, Joseph B; Porucznik, Christina A; Hammoud, Ahmad O; Wactawski-Wende, Jean

2013-03-01

Energy-containing beverages are widely consumed among premenopausal women, but their association with reproductive hormones is not well understood. The objective was to assess the association of energy-containing beverages, added sugars, and total fructose intake with reproductive hormones among ovulatory cycles and sporadic anovulation in healthy premenopausal women. Women (n = 259) in the BioCycle Study were followed for up to 2 menstrual cycles; they provided fasting blood specimens during up to 8 visits/cycle and four 24-h dietary recalls/cycle. Women who consumed ≥1 cup (1 cup = 237 mL) sweetened soda/d had 16.3% higher estradiol concentrations compared with women who consumed less sweetened soda (86.5 pg/mL compared with 74.4 pg/mL, P = 0.01) after adjustment for age, BMI, race, dietary factors, and physical activity. Similarly elevated estradiol concentrations were found for ≥1 cup cola/d and noncola soda intake. Neither artificially sweetened soda nor fruit juice intake ≥1 cup/d was significantly associated with reproductive hormones. Added sugar above the average US woman's intake (≥73.2 g/d) or above the 66th percentile in total fructose intake (≥41.5 g/d) was associated with significantly elevated estradiol but not consistently across all models. No associations were found between beverages, added sugars, or total fructose intake and anovulation after multivariate adjustment. Even at moderate consumption amounts, sweetened soda is associated with elevated follicular estradiol concentrations among premenopausal women but does not appear to affect ovulatory function. Further research into the mechanism driving the association between energy-containing beverages and reproductive hormones, and its potential implications for women's health, is warranted.

Kuosheng Mark III containment analyses using GOTHIC

Energy Technology Data Exchange (ETDEWEB)

Lin, Ansheng, E-mail: samuellin1999@iner.gov.tw; Chen, Yen-Shu; Yuann, Yng-Ruey

2013-10-15

Highlights: • The Kuosheng Mark III containment model is established using GOTHIC. • Containment pressure and temperature responses due to LOCA are presented. • The calculated results are all below the design values and compared with the FSAR results. • The calculated results can be served as an analysis reference for an SPU project in the future. -- Abstract: Kuosheng nuclear power plant in Taiwan is a twin-unit BWR/6 plant, and both units utilize the Mark III containment. Currently, the plant is performing a stretch power uprate (SPU) project to increase the core thermal power to 103.7% OLTP (original licensed thermal power). However, the containment response in the Kuosheng Final Safety Analysis Report (FSAR) was completed more than twenty-five years ago. The purpose of this study is to establish a Kuosheng Mark III containment model using the containment program GOTHIC. The containment pressure and temperature responses under the design-basis accidents, which are the main steam line break (MSLB) and the recirculation line break (RCLB) accidents, are investigated. Short-term and long-term analyses are presented in this study. The short-term analysis is to calculate the drywell peak pressure and temperature which happen in the early stage of the LOCAs. The long-term analysis is to calculate the peak pressure and temperature of the reactor building space. In the short-term analysis, the calculated peak drywell to wetwell differential pressure is 140.6 kPa for the MSLB, which is below than the design value of 189.6 kPa. The calculated peak drywell temperature is 158 °C, which is still below the design value of 165.6 °C. In addition, in the long-term analysis, the calculated peak containment pressure is 47 kPa G, which is below the design value of 103.4 kPa G. The calculated peak values of containment temperatures are 74.7 °C, which is lower than the design value of 93.3 °C. Therefore, the Kuosheng Mark III containment can maintain the integrity after

Hospital costs of central line-associated bloodstream infections and cost-effectiveness of closed vs. open infusion containers. The case of Intensive Care Units in Italy.

Science.gov (United States)

Tarricone, Rosanna; Torbica, Aleksandra; Franzetti, Fabio; Rosenthal, Victor D

2010-05-10

The aim was to evaluate direct health care costs of central line-associated bloodstream infections (CLABSI) and to calculate the cost-effectiveness ratio of closed fully collapsible plastic intravenous infusion containers vs. open (glass) infusion containers. A two-year, prospective case-control study was undertaken in four intensive care units in an Italian teaching hospital. Patients with CLABSI (cases) and patients without CLABSI (controls) were matched for admission departments, gender, age, and average severity of illness score. Costs were estimated according to micro-costing approach. In the cost effectiveness analysis, the cost component was assessed as the difference between production costs while effectiveness was measured by CLABSI rate (number of CLABSI per 1000 central line days) associated with the two infusion containers. A total of 43 cases of CLABSI were compared with 97 matched controls. The mean age of cases and controls was 62.1 and 66.6 years, respectively (p = 0.143); 56% of the cases and 57% of the controls were females (p = 0.922). The mean length of stay of cases and controls was 17.41 and 8.55 days, respectively (p Use of innovative technologies such as closed infusion containers can significantly reduce the incidence of healthcare acquired infection without posing additional burden on hospital budgets.

Treatment of cyanide-contained Waste Water

International Nuclear Information System (INIS)

Scheglov, M.Y.

1999-01-01

This work contains results of theoretical and experimental investigations of possibility to apply industrial ionites of different kinds for recovering complex cyanide of some d-elements (Cu, Zn, an dso on) and free CN-ions with purpose to develop technology and unit for plating plant waste water treatment. Finally, on basis of experimental data about equilibrium kinetic and dynamic characteristic of the sorption in model solutions, strong base anionite in CN- and OH-forms was chosen. This anionite has the best values of operational sorption uptake. Recommendations of using the anionite have been developed for real cyanide-contained wastewater treatment

CONTEMPT-DG containment analysis code

International Nuclear Information System (INIS)

Deem, R.E.; Rousseau, K.

1982-01-01

The assessment of hydrogen burning in a containment building during a degraded core event requires a knowledge of various system responses. These system responses (i.e. heat sinks, fan cooler units, sprays, etc.) can have a marked effect on the overall containment integrity results during a hydrogen burn. In an attempt to properly handle the various system responses and still retain the capability to perform sensitivity analysis on various parameters, the CONTEMPT-DG computer code was developed. This paper will address the historical development of the code, its various features, and the rationale for its development. Comparisons between results from the CONTEMPT-DG analyses and results from similar MARCH analyses will also be given

Analysis of Gamma Dose Rate Caused by Corrosion Products inside the Containment Building of Yonngwang Nuclear Power Plant Unit 3 During Shutdown Period

Energy Technology Data Exchange (ETDEWEB)

Ha, Wi Ho; Kim, Jae Cheon; Kim, Soon Young; Kim, Jong Kyung [Hanyang Univ., Seoul (Korea, Republic of)

2005-07-01

Occupational radiation exposure(ORE) of nuclear power plant(NPP) workers mainly occurs during the shutdown period. Major radioactive sources are the corrosion products released from the reactor coolant system(RCS). The corrosion products consist of circulating crud and deposited crud. Major radioactive corrosion products, {sup 58}Co and {sup 60}Co, are known to contribute approximately more than 70% of the total ORE. In this study, the corrosion products regarding cobalt were evaluated during the shutdown period, and gamma dose rates caused by them were calculated at the main working area inside the containment building of the Yonggwang NPP Unit 3.

Affective reactivity to daily stressors is associated with elevated inflammation.

Science.gov (United States)

Sin, Nancy L; Graham-Engeland, Jennifer E; Ong, Anthony D; Almeida, David M

2015-12-01

Inflammation increases the risk of chronic diseases, but the links between emotional responses to daily events and inflammation are unknown. We examined individual differences in affective reactivity to daily stressors (i.e., changes in positive and negative affect in response to stressors) as predictors of inflammatory markers interleukin-6 (IL-6) and C-reactive protein (CRP). A cross-sectional sample of 872 adults from the National Study of Daily Experiences (substudy of Midlife in the United States II) reported daily stressors and affect during telephone interviews for 8 days. Blood samples were obtained at a separate clinic visit and assayed for inflammatory markers. Multilevel models estimated trait affective reactivity slopes for each participant, which were inputted into regression models to predict inflammation. People who experienced greater decreases in positive affect on days when stressors occurred (i.e., positive affect reactivity) had elevated log IL-6, independent of demographic, physical, psychological, and behavioral factors (B = 1.12, SE = 0.45, p = .01). Heightened negative affect reactivity was associated with higher log CRP among women (p = .03) but not men (p = .57); health behaviors accounted for this association in women. Adults who fail to maintain positive affect when faced with minor stressors in everyday life appear to have elevated levels of IL-6, a marker of inflammation. Women who experience increased negative affect when faced with minor stressors may be at particular risk of elevated inflammation. These findings add to growing evidence regarding the health implications of affective reactivity to daily stressors. (c) 2015 APA, all rights reserved).

Affective reactivity to daily stressors is associated with elevated inflammation

Science.gov (United States)

Sin, Nancy L.; Graham-Engeland, Jennifer E.; Ong, Anthony D.; Almeida, David M.

2015-01-01

Objective Inflammation increases the risk of chronic diseases, but the links between emotional responses to daily events and inflammation are unknown. We examined individual differences in affective reactivity to daily stressors (i.e., changes in positive and negative affect in response to stressors) as predictors of inflammatory markers interleukin-6 (IL-6) and C-reactive protein (CRP). Methods A cross-sectional sample of 872 adults from the National Study of Daily Experiences (sub-study of Midlife in the United States II) reported daily stressors and affect during telephone interviews for 8 days. Blood samples were obtained at a separate clinic visit and assayed for inflammatory markers. Multilevel models estimated trait affective reactivity slopes for each participant, which were inputted into regression models to predict inflammation. Results People who experienced greater decreases in positive affect on days when stressors occurred (i.e, positive affect reactivity) had elevated log IL-6, independent of demographic, physical, psychological, and behavioral factors (B = 1.12, SE = 0.45, p = 0.01). Heightened negative affect reactivity was associated with higher log CRP among women (p = 0.03) but not men (p = 0.57); health behaviors accounted for this association in women. Conclusions Adults who fail to maintain positive affect when faced with minor stressors in everyday life appear to have elevated levels of IL-6, a marker of inflammation. Women who experience increased negative affect when faced with minor stressors may be at particular risk of elevated inflammation. These findings add to growing evidence regarding the health implications of affective reactivity to daily stressors. PMID:26030309

Design of a powered elevator control system. [powered elevator system for modified C-8A aircraft for STOL operation

Science.gov (United States)

Glende, W. L. B.

1974-01-01

The design, fabrication and flight testing of a powered elevator system for the Augmentor Wing Jet STOL Research Aircraft (AWJSRA or Mod C-8A) are discussed. The system replaces a manual spring tab elevator control system that was unsatisfactory in the STOL flight regime. Pitch control in the AWJSRA is by means of a single elevator control surface. The elevator is used for both maneuver and trim control as the stabilizer is fixed. A fully powered, irreversible flight control system powered by dual hydraulic sources was designed. The existing control columns and single mechanical cable system of the AWJSRA have been retained as has been the basic elevator surface, except that the elevator spring tab is modified into a geared balance tab. The control surface is directly actuated by a dual tandem moving body actuator. Control signals are transmitted from the elevator aft quadrant to the actuator by a linkage system that includes a limited authority series servo actuator.

Magnesium sacrificial anode behavior at elevated temperature

International Nuclear Information System (INIS)

Othman, Mohsen Othman

2006-01-01

Magnesium sacrificial anode coupled to mild steel was tasted in sodium chloride and tap water environments at elevated temperatures. The anode failed to protect the mild steel specimens in tap water environment at all temperatures specified. This was partly due to low conductivity of this medium. The temperature factor did not help to activate the anode in this medium. In sodium chloride environment the anode demonstrated good protection for steel cathodes. The weight loss was high for magnesium in sodium chloride environment particularly beyond 60 degree centigrade. In tap water environment the weight loss was negligible for the anode. It also suffered localized shallow pitting corrosion. Magnesium anode cannot be utilized where high temperature is involved particularly in high conductivity mediums. Protection of structures containing high resistivity waters is not feasible using sacrificial anode system. (author)

Is moral elevation an approach-oriented emotion?

OpenAIRE

Van de Vyver, Julie; Abrams, Dominic

2016-01-01

Abstract Two studies were designed to test whether moral elevation should be conceptualized as an approach-oriented emotion. The studies examined the relationship between moral elevation and the behavioral activation and inhibition systems. Study 1 (N?=?80) showed that individual differences in moral elevation were associated with individual differences in behavioral activation but not inhibition. Study 2 (N?=?78) showed that an elevation-inducing video promoted equally high levels of approac...

Increased KPI containing amyloid precursor protein in experimental autoimmune encephalomyelitis brains.

Science.gov (United States)

Beilin, Orit; Karussis, Dimitrios M; Korczyn, Amos D; Gurwitz, David; Aronovich, Ramona; Mizrachi-Kol, Rachel; Chapman, Joab

2007-04-16

Amyloid precursor protein can be translated from three alternatively spliced mRNAs. We measured levels of amyloid precursor protein isoforms containing the Kunitz protease inhibitor domain (KPIAPP), and amyloid precursor protein without the Kunitz protease inhibitor domain (KPIAPP) in brain homogenates of acute experimental autoimmune encephalomyelitis mice. At the preclinical phase of the disease, both KPIAPP and KPIAPP levels were significantly higher in homogenates from brains of autoimmune encephalomyelitis mice, whereas at the acute phase of the disease only KPIAPP remained significantly elevated compared with controls. At the recovery phase, no differences were observed between the groups. The early and isoform-specific elevation of KPIAPP in autoimmune encephalomyelitis mice suggests a possible role for amyloid precursor protein in the immune response mediating the disease.

Containment response and radiological release for a TMLB' accident sequence in a large dry containment

International Nuclear Information System (INIS)

Gasser, R.D.; Bieniarz, P.P.; Tills, J.L.

1987-01-01

An analysis has been performed for the Bellefonte Pressurized Water Reactor (PWR) Unit 1 to determine the containment loading and the radiological releases into the environment from a station blackout accident. A number of issues have been addressed in this analysis, which include the effects of direct heating on containment loading and the effects of fission product heating and natural convection on releases from the primary system. The results indicate that direct heating, which involves more than about 50% of the core, may fail the Bellefonte containment, but natural convection in the Reactor Coolant System (RCS) may lead to overheating and failure of the primary system piping before core slump, thus, eliminating or mitigating direct heating. Releases from the primary system are significantly increased before vessel breach, due to natural circulation, and after vessel breach, due to reevolution of retained fission products by fission product heating of RCS structures. (orig.)

Canadian Rockies Ecoregion: Chapter 4 in Status and trends of land change in the Western United States--1973 to 2000

Science.gov (United States)

Taylor, Janis L.

2012-01-01

The Canadian Rockies Ecoregion covers approximately 18,494 km2 (7,141 mi2) in northwestern Montana (Omernik, 1987; U.S. Environmental Protection Agency, 1997). The east side of the ecoregion is bordered by the Montana Valley and Foothill Prairies Ecoregion, which also forms a large part of the western border of the ecoregion. In addition, the Northern Rockies Ecoregion wraps around the ecoregion to the northwest and south (fig. 1). As the name implies, the Canadian Rocky Mountains are located mostly in Canada, straddling the border between Alberta and British Columbia. However, this ecoregion only includes the part of the northern Rocky Mountains that is in the United States. This ecoregion is characterized by steep, high-elevation mountain ranges similar to most of the rest of the Rocky Mountains. Compared to the Northern Rockies Ecoregion, however, the Canadian Rockies Ecoregion reaches higher elevations and contains a greater proportion of perennial snow and ice (Omernik, 1987) (fig. 2). Over the years, this section of the Rocky Mountains has garnered many different names, including “Crown of the Continent” by George Bird Grinnell (Waldt, 2008) and “Backbone of the World” by the Blackfeet (Pikuni) Nation. Throughout the ecoregion, montane, subalpine, and alpine ecosystems have distinct flora and fauna elevation zones. Glaciers, permanent snowfields, and seasonal snowpack are found at the highest elevations. Spring and summer runoff fills lakes and tarns that form the headwaters of numerous streams and rivers, including the Columbia and Missouri Rivers that flow west and east, respectively, from the Continental Divide.

ST-segment elevation and ventricular tachycardia after ingestion of a common ornamental plant—a case report

Directory of Open Access Journals (Sweden)

Rami A. Jambeih

2012-03-01

This case highlights the importance of public awareness of severe toxicity from Japanese yew or other yew plants. Yews contain taxines that are responsible for the ECG abnormalities due to its inhibitory effect on the cardiac sodium and calcium channels. They cause conduction abnormalities, VT, and ST-segment elevation that can resemble acute myocardial infarction, hyperkalaemia, and Brugada syndrome.

Advanced energy saving hydraulic elevator

Energy Technology Data Exchange (ETDEWEB)

Garrido, A.; Sevilleja, J.; Servia, A.

1993-08-24

An hydraulic elevator is described comprising: a counterweighted elevator comprising a car, a counterweight, and a rope connecting the car and the counterweight; a ram having a first reaction surface for driving one of the car or the counterweight upwardly and a second reaction surface for driving one of the car or the counterweight downwardly; multiplier means for moving the car a distance greater than a stroke of the ram, the multiplier means connecting the ram to the counterweighted elevator, the multiplier means comprising: a first pulley; a second pulley; means for rigidly connecting the first and second pulley, the means having a length corresponding to a rise of the hydraulic elevator, the means attaching to the ram; and a pulley rope which: has a first end attaching to a first fixed point, extends about the first pulley, extends about the second pulley, and has a second end attaching to a second fixed point.

Elevational gradient in clutch size of Red-faced Warblers

Science.gov (United States)

Dillon, Kristen G.; Conway, Courtney J.

2015-01-01

Our understanding of life history evolution has benefited from debates regarding the underlying causes, and geographic ubiquity, of spatial patterns in avian clutch sizes. Past studies have revealed that birds lay smaller clutch sizes at higher elevation. However, in most previous studies, investigators have failed to adequately control for elevational differences in breeding phenology. To better understand the elevational gradient in avian clutch size, we need to know how clutch size changes across the entire elevational breeding range of a species (i.e., the shape of the relationship between elevation and clutch size), and whether the elevational gradient in clutch size is merely an artifact of elevational gradients in breeding phenology or breeding season length. We examined the relationship between breeding elevation and clutch size of Red-faced Warblers (Cardellina rubrifrons) along a 1000-m elevational gradient in Arizona. Our objectives were to determine how clutch size changed with elevation, and if the relationship between clutch size and elevation merely reflected elevational changes in breeding season length or phenology. The proportion of 5-egg clutches decreased and the proportion of 3- and 4-egg clutches increased non-linearly with increasing elevation, even after controlling for the elevational gradient in nest initiation date. Thus, average clutch size declined across the elevational breeding range of Red-faced Warblers, but this decline was not due to elevational variation in breeding phenology. Timing of breeding changed, but the duration of the breeding season did not change appreciably across the elevational gradient. Hence, elevational differences in breeding season length or breeding phenology cannot explain why Red-faced Warblers (and perhaps other birds) breeding at higher elevations have smaller clutches.

Morphological Analyses and Simulated Flood Elevations in a Watershed with Dredged and Leveed Stream Channels, Wheeling Creek, Eastern Ohio

Science.gov (United States)

Sherwood, James M.; Huitger, Carrie A.; Ebner, Andrew D.; Koltun, G.F.

2008-01-01

The USGS, in cooperation with the Ohio Emergency Management Agency, conducted a study in the Wheeling Creek Basin to (1) evaluate and contrast land-cover characteristics from 2001 with characteristics from 1979 and 1992; (2) compare current streambed elevation, slope, and geometry with conditions present in the late 1980s; (3) look for evidence of channel filling and over widening in selected undredged reaches; (4) estimate flood elevations for existing conditions in both undredged and previously dredged reaches; (5) evaluate the height of the levees required to contain floods with selected recurrence intervals in previously dredged reaches; and (6) estimate flood elevations for several hypothetical dredging and streambed aggradation scenarios in undredged reaches. The amount of barren land in the Wheeling Creek watershed has decreased from 20 to 1 percent of the basin area based on land-cover characteristics from 1979 and 2001. Barren lands appear to have been converted primarily to pasture, presumably as a result of surface-mine reclamation. Croplands also decreased from 13 to 8 percent of the basin area. The combined decrease in barren lands and croplands is approximately offset by the increase in pasture. Stream-channel surveys conducted in 1987 and again in 2006 at 21 sites in four previously dredged reaches of Wheeling Creek indicate little change in the elevation, slope, and geometry of the channel at most sites. The mean change in width-averaged bed and thalweg elevations for the 21 cross sections was 0.1 feet. Bankfull widths, mean depths, and cross-sectional areas measured at 12 sites in undredged reaches were compared to estimates determined from regional equations. The mean percentage difference between measured and estimated bankfull widths was -0.2 percent, suggesting that bankfull widths in the Wheeling Creek Basin are generally about the same as regional averages for undisturbed basins of identical drainage area. For bankfull mean depth and cross

Combined cadmium and elevated ozone affect concentrations of cadmium and antioxidant systems in wheat under fully open-air conditions

International Nuclear Information System (INIS)

Guo, Hongyan; Tian, Ran; Zhu, Jianguo; Zhou, Hui; Pei, Daping; Wang, Xiaorong

2012-01-01

Highlights: ► Combined effect of elevated O 3 and Cd levels on wheat was studied using the free-air concentration enrichment system. ► Elevated O 3 levels result in an increased concentration of Cd in wheat plants grown on Cd-contaminated soils. ► Combined cadmium and elevated O 3 have a significantly synergic effect on oxidative stress in wheat shoots. - Abstract: Pollution of the environment with both ozone (O 3 ) and heavy metals has been steadily increasing. An understanding of their combined effects on plants, especially crops, is limited. Here we studied the effects of elevated O 3 on oxidative stress and bioaccumulation of cadmium (Cd) in wheat under Cd stress using a free-air concentration enrichment (FACE) system. In this field experiment in Jiangdu (Jiangsu Province, China), wheat plants were grown in pots containing soil with various concentrations of cadmium (0, 2, and 10 mg kg −1 Cd was added to the soil) under ambient conditions and under elevated O 3 levels (50% higher than the ambient O 3 ). Present results showed that elevated O 3 led to higher concentrations of Cd in wheat tissues (shoots, husk and grains) with respect to contaminated soil. Combined exposure to Cd and elevated O 3 levels strongly affected the antioxidant isoenzymes POD, APX and CAT and accelerated oxidative stress in wheat leaves. Our results suggest that elevated O 3 levels cause a reduction in food quality and safety.

pH-responsive fluorescence chemical sensor constituted by conjugated polymers containing pyridine rings.

Science.gov (United States)

Adachi, Naoya; Kaneko, Yuki; Sekiguchi, Kazuki; Sugiyama, Hiroki; Sugeno, Masafumi

2015-12-01

Poly(p-pyridinium phenylene ethynylene)s (PPyPE) functionalized with alternating donor-acceptor repeat units were synthesized by a Pd-catalyzed Sonogashira coupling reaction between diethynyl monomer and di-iodopyridine for use as a pH-responsive fluorescence chemical sensor. The synthesized PPyPE, containing pyridine units, was characterized by FT-IR, (1)H and (13)C NMR, UV-visible and fluorescence spectroscopies. We investigated the relationship between changes of optical properties and protonation/deprotonation of PPyPE containing pyridine units in solution. Addition of HCl decreased and red-shifted the fluorescence intensity of the conjugated polymers that contained pyridine rings; fluorescence intensity of the polymers increased upon addition of NaOH solution. The synthesized PPyPE was found to be an effective and reusable chemical sensor for pH sensing. Copyright © 2015 John Wiley & Sons, Ltd.

Routing and Scheduling Problems of Container Trucks in a Shared Resource Environment

OpenAIRE

Jeong, Kyungsoo

2017-01-01

More frequent vehicle movements are required for moving containers in a local area due to low unit volume that a single vehicle can handle compared with vessels and rails involved in the container supply chain. For this reason, truck operations for moving containers significantly affect not only transportation cost itself but also product price. They have inherent operational inefficiencies associated with empty container movements and container processes at facilities such as warehouses, d...

Effects of Elevated CO2 on the Swainsonine Chemotypes of Astragalus lentiginosus and Astragalus mollissimus.

Science.gov (United States)

Cook, Daniel; Gardner, Dale R; Pfister, James A; Stonecipher, Clinton A; Robins, Joseph G; Morgan, Jack A

2017-03-01

Rapid changes in the Earth's atmosphere and climate associated with human activity can have significant impacts on agriculture including livestock production. CO 2 concentration has risen from the industrial revolution to the current time, and is expected to continue to rise. Climatic changes alter physiological processes, growth, and development in numerous plant species, potentially changing concentrations of plant secondary compounds. These physiological changes may influence plant population density, growth, fitness, and toxin concentrations and thus influence the risk of toxic plants to grazing livestock. Locoweeds, swainsonine-containing Astragalus species, are one group of plants that may be influenced by climate change. We evaluated how two different swainsonine-containing Astragalus species responded to elevated CO 2 concentrations. Measurements of biomass, crude protein, water soluble carbohydrates and swainsonine concentrations were measured in two chemotypes (positive and negative for swainsonine) of each species after growth at CO 2 levels near present day and at projected future concentrations. Biomass and water soluble carbohydrate concentrations responded positively while crude protein concentrations responded negatively to elevated CO 2 in the two species. Swainsonine concentrations were not strongly affected by elevated CO 2 in the two species. In the different chemotypes, biomass responded negatively and crude protein concentrations responded positively in the swainsonine-positive plants compared to the swainsonine-negative plants. Ultimately, changes in CO 2 and endophyte status will likely alter multiple physiological responses in toxic plants such as locoweed, but it is difficult to predict how these changes will impact plant herbivore interactions.

Defense of a space elevator

Energy Technology Data Exchange (ETDEWEB)

Laubscher, B. E. (Bryan E.)

2004-01-01

The Space Elevator (SE) represents a major paradigm shift in space access. If the SE's promise of low-cost access is to be realized, everything becomes economically more feasible to accomplish in space. In this paper we describe a defensive system of the SE. The primary scenario adopted for this analysis is the SE based on a floating platform in the ocean along the equator. A second possible scenario is the SE stationed on land (island or continent) on or near the equator. The SE will capture the imaginations of people around the world. It will become a symbol of power, capability, wealth and prestige for the country that builds it. As such, it will become a prime terrorist target. Moreover, the tremendous economic leverage afforded by the SE might motivate rogue nations to plot its destruction. Therefore, it is necessary to consider the requirements for defense of the SE. For the purposes of this paper it is assumed that the SE is to be deployed by the United States or one of its companies, and the resources of the US are available for its defense.

Control unit of a nuclear reactor

International Nuclear Information System (INIS)

Desfontaines, Guy; Le Helloco, Michel.

1981-01-01

Control unit comprising multiple leak-tight vessels, in communication with the inside of the reactor vessel, extending this vessel above its cover, in the vertical direction and each one enclosing a mechanism for moving a cluster of material absorbing the neutrons in the reactor core, actuated by a motor. This control unit is of reduced height above the vessel cover and provides efficient protection of the leak tight containments and the mechanisms in the event of earthquakes, easy removal and refitting of the vessel cover, good ventilation of the power devices of the mechanisms without the use of a complex ventilation system, efficient thermal insulation of the leak-tight containments assembly, as well as easy access to the motors and mechanism located in the leak-tight containment for carrying out any maintenance and repairs that might be required [fr

The principle and data analysis of online monitoring system of containment leak rate

International Nuclear Information System (INIS)

Zhang Chunwei; Yang Yongdeng; Qiao Yu; Liang Bo

2014-01-01

The use of online monitoring system of containment leak rate (EPP) in Qinshan 2nd nuclear power plant is introduced. When the containment leak rate reaches the operational limit, the system will automatically alarm and inform the unit operator to take the necessary action. But it is found that the EPP will give a mendacious alarm of 'Containment leak rate abnormity' once in a while during use. The mendacious alarm has an effect on the normal operation of the unit. The reason of the mendacious alarm is analyzed. The data monitored by the EPP are relative hysteretic and the veracity of the flow of compressed air into the containment has a significant influence on the data monitored by the EPP. (authors)

46 CFR 120.540 - Elevators.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Elevators. 120.540 Section 120.540 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150 PASSENGERS OR WITH OVERNIGHT ACCOMMODATIONS FOR MORE THAN 49 PASSENGERS ELECTRICAL INSTALLATION Miscellaneous Systems and Requirements § 120.540 Elevators....

Surface Elevation Change of Transantarctic Outlet Glaciers using Historical Aerial Imagery and Structure-from-Motion Photogrammetry

Science.gov (United States)

Child, S. F.; Stearns, L. A.; Girod, L.

2017-12-01

Transantarctic Mountain outlet glaciers drain ice from the East Antarctic Ice Sheet to the Ross Ice Shelf and are generally considered to be stable. However, studies that assess these glaciers typically use data with coarse spatial resolutions (1 - 20 km) and span only the last 15 - 20 years. Here, we use trimetrogon aerial (TMA) photographs collected by the United States Geological Survey from 1960 - 1965 to create historical surface elevation maps. We construct elevations from both the vertical (0° nadir) and oblique photographs using MicMac, a Structure-from-Motion (SfM) software. With typical SfM processing, accurate ground control points (GCPs) are necessary for the best results; however, in situ GCPs are extremely sparse in Antarctica, so we manually identify GCPs using exposed rock outcrops in the WorldView imagery. The historical glacier surface elevations are then compared with present-day elevations derived from WorldView imagery. With this methodology, we assess how Transantarctic outlet glaciers have changed over 55 years. Recent studies indicate thinning of the eastern Ross Ice Shelf, where it borders the Transantarctic Mountains. With long-term records of glacier elevation change, we can differentiate whether ice shelf thinning is driven by changes in glacier or ocean dynamics. These results give us a better understanding of the long-term stability of East Antarctic outlet glaciers, which is essential in improving predictive models of ice sheet behavior.

Study on the shear transfer of reinforced concrete at elevated temperature

International Nuclear Information System (INIS)

Ishida, Hiroaki; Kanazu, Tsutomu

1989-01-01

Reinforced concrete structures in nuclear power stations, such as a containment vessel and structural members supporting a reactor vessel, are designed assuming that they may be subjected to elevated temperature. In the design code, it is specified that the temperature of concrete must not exceed the limitation, and thermal effect shall be taken into account. In this study, the shearing test using Mattock type specimens was performed to investigate into the shear behavior of the reinforced concrete subjected to elevated temperature. The test parameters studied in this program were the reinforcement ratio in a shear plane, the compressive stress normal to a shear plane and temperature. The maximum shearing load of the specimens heated to 200 degC was about 10-20 % lower than that at normal temperature, but nearly equal to that of the specimens heated to 100 degC. The equation for evaluating the shearing strength ratio was proposed. The cracking width and slip at maximum shearing load increased as temperature rose. Up to 200 degC, the same relation existed between interface shear transfer rigidity and cracking width. (K.I.)

Elevated service water temperature systems analysis for a nuclear power plant

International Nuclear Information System (INIS)

Lewis, T.; Hurt, W.

1992-01-01

This paper describes analyses performed to support the evaluation of the effects of elevated Service Water (SW) temperatures on the operation of a Pressurized Water Reactor. The purpose of the analyses is to provide justification of continued plant operation with SW temperatures up to 5 degrees F (3 degrees C) above the original temperature design limit. The study involved evaluation of the following major components or plant transients: Containment Design Basis Accident (DBA), Emergency Diesel Generator (EDG), Plant Cooldown, Engineered Safety Feature (ESF) Room Coolers, Engineered Safety Feature Pumps, and Assessment for Impact on Normal Operation. The principal objective was related to raising the design maximum temperature of the SW system from 95 degrees F (35 degrees C) to 100 degrees F (38 degrees C). since the Service Water system is safety related, an serves a plant during both normal and design basis conditions, a wide variety of components must be analyzed under various operating modes. The evaluation of systems and components affected by elevated SW temperature is presented, along with conclusions

Model predictions and control of conditions in a CA-reefer container

NARCIS (Netherlands)

Sman, van der R.G.M.; Verdijck, G.J.C.

2003-01-01

In this paper a concept for energy saving for refrigerated container transport is presented. The concept is based on model-predictive control of the set points of the cooling unit. These models predict energy consumption of the cooling unit, climatic conditions inside the cargo space, and the change

Differential lead retention in zircons: implications for nuclear waste containment.

Science.gov (United States)

Gentry, R V; Sworski, T J; McKown, H S; Smith, D H; Eby, R E; Christie, W H

1982-04-16

An innovative ultrasensitive technique was used for lead isotopic analysis of individual zircons extracted from granite core samples at depths of 960, 2170, 2900, 3930, and 4310 meters. The results show that lead, a relatively mobile element compared to the nuclear waste-related actinides uranium and thorium, has been highly retained at elevated temperatures (105 degrees to 313 degrees C) under conditions relevant to the burial of synthetic rock waste containers in deep granite holes.

Object-oriented classification of drumlins from digital elevation models

Science.gov (United States)

Saha, Kakoli

Drumlins are common elements of glaciated landscapes which are easily identified by their distinct morphometric characteristics including shape, length/width ratio, elongation ratio, and uniform direction. To date, most researchers have mapped drumlins by tracing contours on maps, or through on-screen digitization directly on top of hillshaded digital elevation models (DEMs). This paper seeks to utilize the unique morphometric characteristics of drumlins and investigates automated extraction of the landforms as objects from DEMs by Definiens Developer software (V.7), using the 30 m United States Geological Survey National Elevation Dataset DEM as input. The Chautauqua drumlin field in Pennsylvania and upstate New York, USA was chosen as a study area. As the study area is huge (approximately covers 2500 sq.km. of area), small test areas were selected for initial testing of the method. Individual polygons representing the drumlins were extracted from the elevation data set by automated recognition, using Definiens' Multiresolution Segmentation tool, followed by rule-based classification. Subsequently parameters such as length, width and length-width ratio, perimeter and area were measured automatically. To test the accuracy of the method, a second base map was produced by manual on-screen digitization of drumlins from topographic maps and the same morphometric parameters were extracted from the mapped landforms using Definiens Developer. Statistical comparison showed a high agreement between the two methods confirming that object-oriented classification for extraction of drumlins can be used for mapping these landforms. The proposed method represents an attempt to solve the problem by providing a generalized rule-set for mass extraction of drumlins. To check that the automated extraction process was next applied to a larger area. Results showed that the proposed method is as successful for the bigger area as it was for the smaller test areas.

Aging management and life extension - Containment aging study

International Nuclear Information System (INIS)

Tai, Tom M.; Deng, Daniel

2004-01-01

Bechtel is currently completing an aging study on a concrete containment structure. The target plant is a two-unit PWR plant with a generating capacity of about 850 MWe from each unit. Both units are less than 20 years old. The total electrical energy output from this plant site accounts for more than 50% of the utility's baseload operation. Although no utility in the United States has made a decision to submit a license renewal application, some have begun to investigate the feasibility of developing an life cycle management (LCM) program for a strategy to operate their plants efficiently, to investigate the financial benefit and safety implications of license renewal to operate their nuclear power plants beyond their current licensed periods, and to prepare a program plan for plant decommissioning. The LCM program includes economic, environmental, regulatory and technical aspects of continuing plant operations beyond the current license period. The Electric Power Research Institute (EPRI) has been supportive to assist utilities and owners groups in their research and development efforts to develop the technical requirements and the issues associated with important to license renewal structures. The focus of this paper is on the technical issues related to the evaluation of the material condition of the containment structure with respect to aging and the effective management of that aging. (author)

Elevational characteristics of the archaeal community in full-scale activated sludge wastewater treatment plants at a 3,660-meter elevational scale.

Science.gov (United States)

Niu, Lihua; Zhang, Xue; Li, Yi; Wang, Peifang; Zhang, Wenlong; Wang, Chao; Wang, Qing

2017-07-01

Due to the important roles of archaea in wastewater treatment processes, archaeal communities have been studied extensively in various anaerobic reactors, but the knowledge of archaeal communities in full-scale activated sludge wastewater treatment plants (WWTPs) remains quite poor. In this study, 454-pyrosequencing was for the first time employed to investigate archaeal communities from 20 full-scale activated sludge WWTPs distributed at a 3,660-meter elevational scale in China. Results showed that archaeal communities from WWTPs were dominated by Methanosarcinales (84.6%). A core archaeal population (94.5%) composed of Methanosaeta, Methanosarcina, Methanogenium and Methanobrevibacter was shared among WWTPs. The elevational pattern of archaeal communities was observed in WWTPs, with an elevational threshold associated with archaeal community richness and structures at approximately 1,500 meters above sea level (masl). A declining trend in community richness with increasing elevation was observed at higher elevations, whereas no trend was presented at lower elevations. Spearman correlation analysis indicated that the archaeal community richness at higher elevations was associated with more environmental variables than that at lower elevations. Redundancy analysis indicated that wastewater variables were the dominant contributors to the variation of community structures at higher elevations, followed by operational variables and elevation.

Filtered containment venting in Sweden

International Nuclear Information System (INIS)

Lindau, L.; Ellisson, K.

1989-01-01

After the TMI accident, Swedish authorities decided that all Swedish nuclear power plants should be upgraded with respect to mitigation of the consequences of severe accidents. One contribution to meet these ends is filtered containment venting, i.e. means to relieve containment overpressure and to clean the relief gas from radioactive components. The first system in operation was built at the Barsebaeck site (2 BWR's) where a gravel bed filter was installed. For the remaining Swedish units (7 BWR's and 3 PWR's) a passive, self-controlling wet scrubber system, FILTRA-MVSS, is now under installation. The principle of the FILTRA-MVSS is a self-controlling, self-pumping venturi collector submerged in a pool, and it is used to filter out emissions of solid and gaseous radioactive components

Using historical aerial photography and softcopy photogrammetry for waste unit mapping in L Lake

International Nuclear Information System (INIS)

Christel, L.M.

1997-10-01

L Lake was developed as a cooling water reservoir for the L Reactor at the Savannah River Site. The construction of the lake, which began in the fall of 1984, altered the structure and function of Steel Creek. Completed in the fall of 1985, L Lake has a capacity of 31 million cubic meters and a normal pool of 58 meters. When L Reactor operations ceased in 1988, the water level in the lake still had to be maintained. Site managers are currently trying to determine the feasibility of draining or drawing down the lake in order to save tax dollars. In order to understand the full repercussions of such an undertaking, it was necessary to compile a comprehensive inventory of what the lake bottom looked like prior to filling. Aerial photographs, acquired nine days before the filling of the lake began, were scanned and used for softcopy photogrammetry processing. A one-meter digital elevation model was generated and a digital orthophoto mosaic was created as the base map for the project. Seven categories of features, including the large waste units used to contain the contaminated soil removed from the dam site, were screen digitized and used to generate accurate maps. Other map features include vegetation waste piles, where contaminated vegetation from the flood plain was contained, and ash piles, which are sites where vegetation debris was burned and then covered with clean soil. For all seven categories, the area of disturbance totaled just over 63 hectares. When the screen digitizing was completed, the elevation at the centroid of each disturbance was determined. When the information is used in the Savannah River Site Geographical Information System, it can be used to visualize the various L Lake draw-down scenarios suggested by site managers and hopefully, to support evaluations of the cost effectiveness for each proposed activity

Space Elevator Concept Considered a Reality

Science.gov (United States)

2000-01-01

The `once upon a time' science fiction concept of a space elevator has been envisioned and studied as a real mass transportation system in the latter part of the 21st century. David Smitherman of NASA's Marshall Space Flight Center's Advanced Projects Office has compiled plans for such an elevator. The space elevator concept is a structure extending from the surface of the Earth to geostationary Earth orbit (GEO) at 35,786 km in altitude. The tower would be approximately 50 km tall with a cable tethered to the top. Its center mass would be at GEO such that the entire structure orbits the Earth in sync with the Earth's rotation maintaining a stationary position over its base attachment at the equator. Electromagnetic vehicles traveling along the cable could serve as a mass transportation system for transporting people, payloads, and power between space and Earth. This illustration by artist Pat Rawling shows the concept of a space elevator as viewed from the geostationary transfer station looking down the length of the elevator towards the Earth.

Containment test in area of high latitude and low temperature

International Nuclear Information System (INIS)

Cai Jiantao; Ni Yongsheng; Jia Wutong

2014-01-01

The effects of high latitude and low temperature on containment test are detailed analyzed from the view of design, equipment, construct and start-up, and the solution is put forward. The major problems resolved is as below: the effects of low temperature and high wind on defect inspection of the containment surface, the effects of test load on the affiliated equipment of containment in the condition of low temperature, and the effects of low temperature on the containment leak rate measurement. Application in Hongyanhe Unit 1 showed that the proposed scheme can effectively overcome the influence of adverse weather on the containment test. (authors)

Coffee bean extracts rich and poor in kahweol both give rise to elevation of liver enzymes in healthy volunteers

Directory of Open Access Journals (Sweden)

Schouten Evert G

2004-07-01

Full Text Available Abstract Background Coffee oil potently raises serum cholesterol levels in humans. The diterpenes cafestol and kahweol are responsible for this elevation. Coffee oil also causes elevation of liver enzyme levels in serum. It has been suggested that cafestol is mainly responsible for the effect on serum cholesterol levels and that kahweol is mainly responsible for the effect on liver enzyme levels. The objective of this study was to investigate whether coffee oil that only contains a minute amount of kahweol indeed does not cause elevation of liver enzyme levels. Methods The response of serum alanine aminotransferase (ALAT and aspartate aminotransferase (ASAT to Robusta coffee oil (62 mg/day cafestol, 1.6 mg/day kahweol was measured in 18 healthy volunteers. Results After nine days one subject was taken off Robusta oil treatment due to an ALAT level of 3.6 times the upper limit of normal (ULN. Another two subjects stopped treatment due to other reasons. After 16 days another two subjects were taken off Robusta oil treatment. One of those subjects had levels of 5.8 ULN for ALAT and 2.0 ULN for ASAT; the other subject had an ALAT level of 12.4 ULN and an ASAT level of 4.7 ULN. It was then decided to terminate the study. The median response of subjects to Robusta oil after 16 days was 0.27 ULN (n = 15, 25th,75th percentile: 0.09;0.53 for ALAT and 0.06 ULN (25th,75th percentile -0.06;0.22 for ASAT. Conclusions We conclude that the effect on liver enzyme levels of coffee oil containing hardly any kahweol is similar to that of coffee oil containing high amounts of kahweol. Therefore it is unlikely that kahweol is the component of coffee oil that is responsible for the effect. Furthermore, we conclude that otherwise unexplained elevation of liver enzyme levels observed in patients might be caused by a switch from consumption of filtered coffee to unfiltered coffee.

Hospital costs of central line-associated bloodstream infections and cost-effectiveness of closed vs. open infusion containers. The case of Intensive Care Units in Italy

Directory of Open Access Journals (Sweden)

Torbica Aleksandra

2010-05-01

Full Text Available Abstract Objectives The aim was to evaluate direct health care costs of central line-associated bloodstream infections (CLABSI and to calculate the cost-effectiveness ratio of closed fully collapsible plastic intravenous infusion containers vs. open (glass infusion containers. Methods A two-year, prospective case-control study was undertaken in four intensive care units in an Italian teaching hospital. Patients with CLABSI (cases and patients without CLABSI (controls were matched for admission departments, gender, age, and average severity of illness score. Costs were estimated according to micro-costing approach. In the cost effectiveness analysis, the cost component was assessed as the difference between production costs while effectiveness was measured by CLABSI rate (number of CLABSI per 1000 central line days associated with the two infusion containers. Results A total of 43 cases of CLABSI were compared with 97 matched controls. The mean age of cases and controls was 62.1 and 66.6 years, respectively (p = 0.143; 56% of the cases and 57% of the controls were females (p = 0.922. The mean length of stay of cases and controls was 17.41 and 8.55 days, respectively (p Conclusions CLABSI results in considerable and significant increase in utilization of hospital resources. Use of innovative technologies such as closed infusion containers can significantly reduce the incidence of healthcare acquired infection without posing additional burden on hospital budgets.

Purwarupa Sistem Kontrol Elevator Berbasis Programable Logic Control

Directory of Open Access Journals (Sweden)

Fathahillah Fathahillah

2017-12-01

Full Text Available Various methods / types of controls developed in accordance with industry needs one of them in the field of building automation system. One of the controls in the field of building automation system is the elevator control system (elevator. Early elevator control systems that transport humans or goods as vertical transportation vehicles are still conventional using human power, then evolved using steam engines, until now the elevators use AC motors equipped with control systems. The purpose of this research is to design the prototype of elevator control system using programmable logic control (PLC. The type of PLC controller used in the study using Omron PLC. The results show the design of prototype of elevator control system using PLC successfully and can control eleveator in accordance with its function, besides its programming form can be more simple.

ELEVATED CO{sub 2} IN A PROTOTYPE FREE-AIR CO{sub 2} ENRICHMENT FACILITY AFFECTS PHOTOSYNTHETIC NITROGEN RELATIONS IN A MATURING PINE FOREST

Energy Technology Data Exchange (ETDEWEB)

ELLSWORTH,D.S.; LA ROCHE,J.; HENDREY,G.R.

1998-03-01

A maturing loblolly pine (Pinus taeda L.) forest was exposed to elevated CO{sub 2} in the natural environment in a perturbation study conducted over three seasons using the free-air CO{sub 2} enrichment (FACE) technique. At the time measurements were begun in this study, the pine canopy was comprised entirely of foliage which had developed under elevated CO{sub 2} conditions (atmospheric [CO{sub 2}] {approx} 550 {micro}mol mol{sup {minus}1}). Measurements of leaf photosynthetic responses to CO{sub 2} were taken to examine the effects of elevated CO{sub 2} on photosynthetic N nutrition in a pine canopy under elevated CO{sub 2}. Photosynthetic CO{sub 2} response curves (A-c{sub i} curves) were similar in FACE trees under elevated CO{sub 2} compared with counterpart trees in ambient plots for the first foliage cohort produced in the second season of CO{sub 2} exposure, with changes in curve form detected in the foliage cohorts subsequently produced under elevated CO{sub 2}. Differences in the functional relationship between carboxylation rate and N{sub a} suggest that for a given N{sub a} allocated among successive cohorts of foliage in the upper canopy, V{sub c max} was 17% lower in FACE versus Ambient trees. The authors also found that foliar Rubisco content per unit total protein derived from Western blot analysis was lower in late-season foliage in FACE foliage compared with ambient-grown foliage. The results illustrate a potentially important mode of physiological adjustment to growth conditions that may operate in forest canopies. Their findings suggest that mature loblolly pine trees growing in the field may have the capacity for shifts in intrinsic nitrogen utilization for photosynthesis under elevated CO{sub 2} that are not dependent on changes in leaf N. While carboxylation efficiency per unit N apparently decreased under elevated CO{sub 2}, photosynthetic rates in trees at elevated CO{sub 2} concentrations {approx} 550 pmol mol{sub {minus}1} are still

A simplified approach for evaluating secondary stresses in elevated temperature design

International Nuclear Information System (INIS)

Becht, C.

1983-01-01

Control of secondary stresses is important for long-term reliability of components, particularly at elevated temperatures where substantial creep damage can occur and result in cracking. When secondary stresses are considered in the design of elevated temperature components, these are often addressed by the criteria contained in Nuclear Code Case N-47 for use with elastic or inelastic analysis. The elastic rules are very conservative as they bound a large range of complex phenomena; because of this conservatism, only components in relatively mild services can be designed in accordance with these rules. The inelastic rules, although more accurate, require complex and costly nonlinear analysis. Elevated temperature shakedown is a recognized phenomenon that has been considered in developing Code rules and simplified methods. This paper develops and examines the implications of using a criteria which specifically limits stresses to the shakedown regime. Creep, fatigue, and strain accumulation are considered. The effect of elastic follow-up on the conservatism of the criteria is quantified by means of a simplified method. The level of conservatism is found to fall between the elastic and inelastic rules of N-47 and, in fact, the incentives for performing complex inelastic analyses appear to be low except in the low cycle regime. The criteria has immediate applicability to non-code components such as vessel internals in the chemical, petroleum, and synfuels industry. It is suggested that such a criteria be considered in future code rule development

Synthesis, Properties, Calculations and Applications of Small Molecular Host Materials Containing Oxadiazole Units with Different Nitrogen and Oxygen Atom Orientations for Solution-Processable Blue Phosphorescent OLEDs

Science.gov (United States)

Ye, Hua; Wu, Hongyu; Chen, Liangyuan; Ma, Songhua; Zhou, Kaifeng; Yan, Guobing; Shen, Jiazhong; Chen, Dongcheng; Su, Shi-Jian

2018-03-01

A series of new small molecules based on symmetric electron-acceptor of 1,3,4-oxadiazole moiety or its asymmetric isomer of 1,2,4-oxadiazole unit were successfully synthesized and applied to solution-processable blue phosphorescent organic light-emitting diodes for the first time, and their thermal, photophysical, electrochemical properties and density functional theory calculations were studied thoroughly. Due to the high triplet energy levels ( E T, 2.82-2.85 eV), the energy from phosphorescent emitter of iridium(III) bis[(4,6-difluorophenyl)-pyridinate- N,C2']picolinate (FIrpic) transfer to the host molecules could be effectively suppressed and thus assuring the emission of devices was all from FIrpic. In comparison with the para-mode conjugation in substitution of five-membered 1,3,4-oxadiazole in 134OXD, the meta-linkages of 1,2,4-isomer appending with two phenyl rings cause the worse conjugation degree and the electron delocalization as well as the lower electron-withdrawing ability for the other 1,2,4-oxadiazole-based materials. Noting that the solution-processed device based on 134OXD containing 1,3,4-oxadiazole units without extra vacuum thermal-deposited hole/exciton-blocking layer and electron-transporting layer showed the highest maximum current efficiency (CEmax) of 8.75 cd/A due to the excellent charge transporting ability of 134OXD, which far surpassed the similar devices based on other host materials containing 1,2,4-oxadiazole units. Moreover, the device based on 134OXD presented small efficiency roll-off with current efficiency (CE) of 6.26 cd/A at high brightness up to 100 cd/m2. This work demonstrates different nitrogen and oxygen atom orientations of the oxadiazole-based host materials produce major impact on the optoelectronic characteristics of the solution-processable devices.

Isolation and partial characterization of mutants with elevated lipid content in Chlorella sorokiniana and Scenedesmus obliquus.

Science.gov (United States)

Vigeolas, Hélène; Duby, Francéline; Kaymak, Esra; Niessen, Guillaume; Motte, Patrick; Franck, Fabrice; Remacle, Claire

2012-11-30

This paper describes the isolation and partial biomass characterization of high triacylglycerol (TAG) mutants of Chlorella sorokiniana and Scenedesmus obliquus, two algal species considered as potential source of biodiesel. Following UV mutagenesis, 2000 Chlorella and 2800 Scenedesmus colonies were screened with a method based on Nile Red fluorescence. Several mutants with high Nile Red fluorescence were selected by this high-throughput method in both species. Growth and biomass parameters of the strongest mutants were analyzed in detail. All of the four Chlorella mutants showed no significant changes in growth rate, cell weight, cell size, protein and chlorophyll contents on a per cell basis. Whereas all contained elevated total lipid and TAG content per unit of dry weight, two of them were also affected for starch metabolism, suggesting a change in biomass/storage carbohydrate composition. Two Scenedesmus mutants showed a 1.5 and 2-fold increased cell weight and larger cells compared to the wild type, which led to a general increase of biomass including total lipid and TAG content on a per cell basis. Such mutants could subsequently be used as commercial oleaginous algae and serve as an alternative to conventional petrol. Copyright © 2012 Elsevier B.V. All rights reserved.

Hvordan understøttes hg-elevers kompetenceudvikling

DEFF Research Database (Denmark)

Svejgaard, Karin Løvenskjold; Hansen, Jens Ager; Karmark, Ole

Publikationen handler om, hvordan hg-elever arbejder og dermed lærer og udvikler kvalifikationer og kompetencer i de undervisnings- og arbejdsformer, de indgår i. Indholdet er baseret på observationer af elever i klasseundervisning, gruppearbejde eller individuel arbejde i forlængelse af klasseun......Publikationen handler om, hvordan hg-elever arbejder og dermed lærer og udvikler kvalifikationer og kompetencer i de undervisnings- og arbejdsformer, de indgår i. Indholdet er baseret på observationer af elever i klasseundervisning, gruppearbejde eller individuel arbejde i forlængelse af...

Machine-roomless elevator, SPACEL{sub TM}; Machine roomless elevator SPACEL{sub TM} `Supesuseru{sub TM}`

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A machine-roomless elevator, SPACEL{sub TM} requiring no machine room, which operates at a rated speed of 45 and 60 m/min, was put on sale in August 1998 with arrangement for passenger use, residential use and bed use. Another elevator operating at a rated speed of 90 and 105 m/min whose travel distance was extended to 75 m was added to the product series and put on sale in February 1999. The control equipment having been installed in a machine room conventionally was modified to a thickness of 100 mm by adopting an inverter device of thin design and densely mounted substrates. The control equipment was installed on the uppermost floor. The winch is a compact and thin type gearless winch incorporating a permanent magnet synchronizing motor, which was installed at the top of the hoistway. These arrangements have realized a machine-roomless elevator. Further system efficiency improvement has achieved energy conservation of about 10% as compared to the conventional rope type and about 80% as compared to the hydraulic type elevators. (translated by NEDO)

77 FR 48542 - United States

Science.gov (United States)

2012-08-14

... litigation.'' United States v. Armour and Co., 402 U.S. 673, 681 (1971). Section 5 of the Clayton Act... relief in consent judgment that contained recitals in which defendants asserted their innocence); Armour...

Safe electrical design of mine elevator control systems

Energy Technology Data Exchange (ETDEWEB)

Barkand, T.D. [Mine Safety and Health Administration, Pittsburgh, PA (United States)

1995-12-31

A mine elevator recently experienced an ascending car overspeed accident resulting in serious injuries to four passengers. Although the four miners laid down on the floor prior to impact, the miners struck the ceiling of the elevator car as it collided into the overhead structure at an estimated speed four times faster than normal. Several electrical design precautions can be implemented to prevent elevator control system failures. This paper examines safe electrical design of elevator control systems. Supplemental circuits and devices which improve the safety integrity and maintenance of the elevator control system are presented. These circuits and devices provide protection that eliminates the potential hazard and significantly reduces the possibility of a mine elevator accident.

Safe electrical design of mine elevator control systems

Energy Technology Data Exchange (ETDEWEB)

Barkand, T.D. [Mine Safety and Health Administration, Pittsburgh, PA (United States)

1997-03-01

A mine elevator recently experienced an ascending-car overspeed accident, resulting in serious injuries to four passengers. Although the four miners laid down on the floor prior to impact, the miners struck the ceiling of the elevator car as it collided into the overhead structure at an estimated speed four times faster than normal. Several electrical design precautions can be implemented to prevent elevator control system failures. This paper examines safe electrical design of elevator control systems. Supplemental circuits and devices which improve the safety integrity and maintenance of the elevator control system are presented. These circuits and devices provide protection that eliminates the potential hazard and significantly reduces the possibility of a mine elevator accident.

Trend of elevator-related accidents in tehran.

Science.gov (United States)

Khaji, Ali; Ghodsi, Syyed Mohammad

2014-06-01

Elevator-related accidents are uncommon, but can cause significant injury. However, little data exist on these types of accidents. To compile and analyze accident data involving elevators in an effort to eliminate or at least significantly reduce such accidents. In this retrospective study we investigated 1,819 cases of elevator-related accidents during a four-year period (1999-2003) in Tehran. The data were obtained from the Tehran Safety Services & Fire Fighting Organization (TSFO) that is officially and solely responsible to conduct rescue missions of civilians in Tehran. The number of elevator accidents has increased steadily during the four year study period. During these four years there was a positive upward trend for serious injuries and mortality resulting from elevator accidents. Technical problems were the main cause with 74.5%, followed by power loss and overcapacity riding with 11.5% and 7.9% respectively. Sixty-three individuals sustained serious injury and 15 people died as a result of elevator accidents. The number of accidents was significantly higher in summer (x2=18.32, P=0.032) and a considerable proportion of incidences (54%, 947 cases out of 1819) occurred between 5 and 12 pm. Establishment of an organization to inspect the settings, maintenance, and repair of elevators is necessary.