WorldWideScience

Sample records for unit test devices

  1. [Testing system design and analysis for the execution units of anti-thrombotic device].

    Science.gov (United States)

    Li, Zhelong; Cui, Haipo; Shang, Kun; Liao, Yuehua; Zhou, Xun

    2015-02-01

    In an anti-thrombotic pressure circulatory device, relays and solenoid valves serve as core execution units. Thus the therapeutic efficacy and patient safety of the device will directly depend on their performance. A new type of testing system for relays and solenoid valves used in the anti-thrombotic device has been developed, which can test action response time and fatigue performance of relay and solenoid valve. PC, data acquisition card and test platform are used in this testing system based on human-computer interaction testing modules. The testing objectives are realized by using the virtual instrument technology, the high-speed data acquisition technology and reasonable software design. The two sets of the system made by relay and solenoid valve are tested. The results proved the universality and reliability of the testing system so that these relays and solenoid valves could be accurately used in the antithrombotic pressure circulatory equipment. The newly-developed testing system has a bright future in the aspects of promotion and application prospect.

  2. Liquid Acquisition Device Hydrogen Outflow Testing on the Cryogenic Propellant Storage and Transfer Engineering Design Unit

    Science.gov (United States)

    Zimmerli, Greg; Statham, Geoff; Garces, Rachel; Cartagena, Will

    2015-01-01

    As part of the NASA Cryogenic Propellant Storage and Transfer (CPST) Engineering Design Unit (EDU) testing with liquid hydrogen, screen-channel liquid acquisition devices (LADs) were tested during liquid hydrogen outflow from the EDU tank. A stainless steel screen mesh (325x2300 Dutch T will weave) was welded to a rectangular cross-section channel to form the basic LAD channel. Three LAD channels were tested, each having unique variations in the basic design. The LADs fed a common outflow sump at the aft end of the 151 cu. ft. volume aluminum tank, and included a curved section along the aft end and a straight section along the barrel section of the tank. Wet-dry sensors were mounted inside the LAD channels to detect when vapor was ingested into the LADs during outflow. The use of warm helium pressurant during liquid hydrogen outflow, supplied through a diffuser at the top of the tank, always led to early breakdown of the liquid column. When the tank was pressurized through an aft diffuser, resulting in cold helium in the ullage, LAD column hold-times as long as 60 minutes were achieved, which was the longest duration tested. The highest liquid column height at breakdown was 58 cm, which is 23 less than the isothermal bubble-point model value of 75 cm. This paper discusses details of the design, construction, operation and analysis of LAD test data from the CPST EDU liquid hydrogen test.

  3. Test, Evaluation, and Demonstration of Practical Devices/Systems to Reduce Aerodynamic Drag of Tractor/Semitrailer Combination Unit Trucks

    Energy Technology Data Exchange (ETDEWEB)

    Scott Smith; Karla Younessi; Matt Markstaller; Dan Schlesinger; Bhaskar Bhatnagar; Donald Smith; Bruno Banceu; Ron Schoon; V.K. Sharma; Mark Kachmarsky; Srikant Ghantae; Michael Sorrels; Conal Deedy; Justin Clark; Skip Yeakel; Michael D. Laughlin; Charlotte Seigler; Sidney Diamond

    2007-04-30

    Class 8 heavy-duty trucks account for over three-quarters of the total diesel fuel used by commercial trucks (trucks with GVWRs more than 10,000 pounds) in the United States each year. At the highway speeds at which these trucks travel (i.e., 60 mph or greater), aerodynamic drag is a major part of total horsepower needed to move the truck down the highway, Reductions in aerodynamic drag can yield measurable benefits in fuel economy through the use of relatively inexpensive and simple devices. The goal of this project was to examine a number of aerodynamic drag reduction devices and systems and determine their effectiveness in reducing aerodynamic drag of Class 8 tractor/semitrailer combination-units, thus contributing to DOE's goal of reducing transportation petroleum use. The project team included major heavy truck manufacturers in the United States, along with the management and industry expertise of the Truck Manufacturers Association as the lead investigative organization. The Truck Manufacturers Association (TMA) is the national trade association representing the major North American manufacturers of Class 6-8 trucks (GVWRs over 19,500 lbs). Four major truck manufacturers participated in this project with TMA: Freightliner LLC; International Truck and Engine Corporation; Mack Trucks Inc.; and Volvo Trucks North America, Inc. Together, these manufacturers represent over three-quarters of total Class 8 truck sales in the United States. These four manufacturers pursued complementary research efforts as part of this project. The project work was separated into two phases conducted over a two-year period. In Phase I, candidate aerodynamic devices and systems were screened to focus research and development attention on devices that offered the most potential. This was accomplished using full-size vehicle tests, scale model tests, and computational fluid dynamics analyses. In Phase II, the most promising devices were installed on full-size trucks and their

  4. Color identification testing device

    Science.gov (United States)

    Brawner, E. L.; Martin, R.; Pate, W.

    1970-01-01

    Testing device, which determines ability of a technician to identify color-coded electric wires, is superior to standard color blindness tests. It tests speed of wire selection, detects partial color blindness, allows rapid testing, and may be administered by a color blind person.

  5. Portable Heat Pump Testing Device

    Directory of Open Access Journals (Sweden)

    Kłosowiak R.

    2015-08-01

    Full Text Available The aim of this paper is to present the design and working principle of a portable testing device for heat pumps in the energy recirculation system. The presented test stand can be used for any refrigerating/reverse flow cycle device to calculate the device energy balance. The equipment is made of two portable containers of the capacity of 250 liters to simulate the air heat source and ground heat source with a system of temperature stabilization, compressor heat pump of the coefficient of performance (COP of = 4.3, a failsafe system and a control and measurement system.

  6. Penetration testing using mobile devices

    CSIR Research Space (South Africa)

    Shelembe, S

    2012-10-01

    Full Text Available reliable, it was used in the early 90s ? Disadvantage: ? Fixed workstations ? PCs need larger space ? PC set-up time ? Not easy to hide ? Lack portability ? CSIR 2012 Slide 5 Traditional pen-testing is not complete - why? ? Banning laptops... is not enough, cell-phones can hack too ? Pocket sized device is more convenient, since it is easy to carry around at anytime ? A power plug is not innocent, need to look for activity other than just traditional PCs / devices ? CSIR 2012 Slide 6 Mobile...

  7. Semiautomatic device tests components with biaxial leads

    Science.gov (United States)

    Marshall, T. C.

    1966-01-01

    Semiautomatic device with a four-terminal network tests quantities of components having biaxial leads. The four-terminal network permits the testing of components in different environments. This device is easily modified for completely automatic operation.

  8. Portable basketball rim testing device

    Science.gov (United States)

    Abbott, W. Bruce; Davis, Karl C.

    1993-01-01

    A portable basketball rim rebound testing device 10 is illustrated in two preferred embodiments for testing the rebound or energy absorption characteristics of a basketball rim 12 and its accompanying support to determine likely rebound or energy absorption charcteristics of the system. The apparatus 10 includes a depending frame 28 having a C-clamp 36 for releasably rigidly connecting the frame to the basketball rim 12. A glide weight 60 is mounted on a guide rod 52 permitting the weight 60 to be dropped against a calibrated spring 56 held on an abutment surface on the rod to generate for deflecting the basketball rim and then rebounding the weight upwardly. A photosensor 66 is mounted on the depending frame 28 to sense passage of reflective surfaces 75 on the weight to thereby obtain sufficient data to enable a processing means 26 to calculate the rebound velocity and relate it to an energy absorption percentage rate of the rim system 12. A readout is provided to display the energy absorption percentage.

  9. Cursor Control Device Test Battery

    Science.gov (United States)

    Holden, Kritina; Sandor, Aniko; Pace, John; Thompson, Shelby

    2013-01-01

    The test battery was developed to provide a standard procedure for cursor control device evaluation. The software was built in Visual Basic and consists of nine tasks and a main menu that integrates the set-up of the tasks. The tasks can be used individually, or in a series defined in the main menu. Task 1, the Unidirectional Pointing Task, tests the speed and accuracy of clicking on targets. Two rectangles with an adjustable width and adjustable center- to-center distance are presented. The task is to click back and forth between the two rectangles. Clicks outside of the rectangles are recorded as errors. Task 2, Multidirectional Pointing Task, measures speed and accuracy of clicking on targets approached from different angles. Twenty-five numbered squares of adjustable width are arranged around an adjustable diameter circle. The task is to point and click on the numbered squares (placed on opposite sides of the circle) in consecutive order. Clicks outside of the squares are recorded as errors. Task 3, Unidirectional (horizontal) Dragging Task, is similar to dragging a file into a folder on a computer desktop. Task 3 requires dragging a square of adjustable width from one rectangle and dropping it into another. The width of each rectangle is adjustable, as well as the distance between the two rectangles. Dropping the square outside of the rectangles is recorded as an error. Task 4, Unidirectional Path Following, is similar to Task 3. The task is to drag a square through a tunnel consisting of two lines. The size of the square and the width of the tunnel are adjustable. If the square touches any of the lines, it is counted as an error and the task is restarted. Task 5, Text Selection, involves clicking on a Start button, and then moving directly to the underlined portion of the displayed text and highlighting it. The pointing distance to the text is adjustable, as well as the to-be-selected font size and the underlined character length. If the selection does not

  10. Laminated microchannel devices, mixing units and method of making same

    Science.gov (United States)

    Bennett, Wendy D [Kennewick, WA; Hammerstrom, Donald J [West Richland, WA; Martin, Peter M [Kennewick, WA; Matson, Dean W [Kennewick, WA

    2002-10-17

    A laminated microchannel device is described in which there is a unit operation process layer that has longitudinal channel. The longitudinal channel is cut completely through the layer in which the unit process operation resides. Both the device structure and method of making the device provide significant advantages in terms of simplicity and efficiency. A static mixing unit that can be incorporated in the laminated microchannel device is also described.

  11. Reversible (unitized) PEM fuel cell devices

    Energy Technology Data Exchange (ETDEWEB)

    Mitlitsky, F; Myers, B; Smith, W F; Weisberg, Molter, T M

    1999-06-01

    Regenerative fuel cells (RFCs) are enabling for many weight-critical portable applications, since the packaged specific energy (>400 Wh/kg) of properly designed lightweight RFC systems is several-fold higher than that of the lightest weight rechargeable batteries. RFC systems can be rapidly refueled (like primary fuel cells), or can be electrically recharged (like secondary batteries) if a refueling infrastructure is not conveniently available. Higher energy capacity systems with higher performance, reduced weight, and freedom from fueling infrastructure are the features that RFCs promise for portable applications. Reversible proton exchange membrane (PEM) fuel cells, also known as unitized regenerative fuel cells (URFCs), or reversible regenerative fuel cells, are RFC systems which use reversible PEM cells, where each cell is capable of operating both as a fuel cell and as an electrolyzer. URFCs further economize portable device weight, volume, and complexity by combining the functions of fuel cells and electrolyzers in the same hardware, generally without any system performance or efficiency reduction. URFCs are being made in many forms, some of which are already small enough to be portable. Lawrence Livermore National Laboratory (LLNL) has worked with industrial partners to design, develop, and demonstrate high performance and high cycle life URFC systems. LLNL is also working with industrial partners to develop breakthroughs in lightweight pressure vessels that are necessary for URFC systems to achieve the specific energy advantages over rechargeable batteries. Proton Energy Systems, Inc. (Proton) is concurrently developing and commercializing URFC systems (UNIGEN' product line), in addition to PEM electrolyzer systems (HOGEN' product line), and primary PEM fuel cell systems. LLNL is constructing demonstration URFC units in order to persuade potential sponsors, often in their own conference rooms, that advanced applications based on URFC s are

  12. FATIGUE DEVICE FOR TESTING ANKLE JOINT ENDOPROSTHESES

    Directory of Open Access Journals (Sweden)

    Cristian TOADER-PASTI

    2012-05-01

    Full Text Available The paper proposes a model of a fatigue device for testing dedicated to ankle prostheses. The concept of the testing device relies on two aspects: almost any type of ankle prosthesis can be tested on it and it has to work on INSTRON axial-torsion testing machine. Starting from these requirements, a 3D functional assembly that reproduces the real movement of the ankle joint during gait cycle has been designed. The device is based on a cam-follower mechanism.

  13. Four-terminal electrical testing device

    Science.gov (United States)

    Robinson, Robert L.; Graves, Thomas J.; Hoffman, William C., III

    1987-04-01

    The invention relates to a four-terminal electrical connector device for testing and measuring unknown resistances of initiators used for starting pyrotechnic events aboard the space shuttle. The testing device minimizes contact resistance degradation effects and so improves the reliability of resistance measurements taken with the device. Separate and independent voltage sensing and current supply circuits each include a pair of socket contacts for mating engagement with the pins of the initiator. The unknown resistance that is measured by the device is the resistance of the bridgewire of the initiator which is required to be between 0.95 and 1.15 ohms.

  14. Communicating with residential electrical devices via a vehicle telematics unit

    Science.gov (United States)

    Roth, Rebecca C.; Pebbles, Paul H.

    2016-11-15

    A method of communicating with residential electrical devices using a vehicle telematics unit includes receiving information identifying a residential electrical device to control; displaying in a vehicle one or more controlled features of the identified residential electrical device; receiving from a vehicle occupant a selection of the displayed controlled features of the residential electrical device; sending an instruction from the vehicle telematics unit to the residential electrical device via a wireless carrier system in response to the received selection; and controlling the residential electrical device using the sent instruction.

  15. A versatile magnetic refrigeration test device.

    Science.gov (United States)

    Bahl, C R H; Petersen, T F; Pryds, N; Smith, A

    2008-09-01

    A magnetic refrigeration test device has been built and tested. The device allows variation and control of many important experimental parameters, such as the type of heat transfer fluid, the movement of the heat transfer fluid, the timing of the refrigeration cycle, and the magnitude of the applied magnetic field. An advanced two-dimensional numerical model has previously been implemented in order to help in the optimization of the design of a refrigeration test device. Qualitative agreement between the results from model and the experimental results is demonstrated for each of the four different parameter variations mentioned above.

  16. A versatile magnetic refrigeration test device

    DEFF Research Database (Denmark)

    Bahl, Christian Robert Haffenden; Petersen, Thomas Frank; Pryds, Nini

    2008-01-01

    A magnetic refrigeration test device has been built and tested. The device allows variation and control of many important experimental parameters, such as the type of heat transfer fluid, the movement of the heat transfer fluid, the timing of the refrigeration cycle, and the magnitude...... of the applied magnetic field. An advanced two-dimensional numerical model has previously been implemented in order to help in the optimization of the design of a refrigeration test device. Qualitative agreement between the results from model and the experimental results is demonstrated for each of the four...

  17. [Information safety test of digital medical device].

    Science.gov (United States)

    Liu, Jiong

    2014-07-01

    According to the background of the age of big data, the medical devices are informatized, we analyze the safety and efficiency for the information and data of digital medical devices or medical systems, also discussed some test methods. Lack of a suitable standard system of digital medical devices is a big problem both for domain standard and international standard. GB25000.51 is too ambiguous and free for testing, also not very operational. So this paper suggested some test advices and some prospective method. These test methods are helpful for finding the problem and performing the standards. What's more, these methods are famous in the world and used widely in the 3C region but just start in the medical region, which can promote the development of the medical devices.

  18. HIV Testing in the United States

    Science.gov (United States)

    ... HIV/AIDS HIV Testing in the United States HIV Testing in the United States Jun 23, 2017 ... States or for refugees. 27 Insurance Coverage of HIV Testing HIV testing that is “medically necessary” – recommended ...

  19. Electronic Voltage and Current Transformers Testing Device

    Directory of Open Access Journals (Sweden)

    Yong Xiao

    2012-01-01

    Full Text Available A method for testing electronic instrument transformers is described, including electronic voltage and current transformers (EVTs, ECTs with both analog and digital outputs. A testing device prototype is developed. It is based on digital signal processing of the signals that are measured at the secondary outputs of the tested transformer and the reference transformer when the same excitation signal is fed to their primaries. The test that estimates the performance of the prototype has been carried out at the National Centre for High Voltage Measurement and the prototype is approved for testing transformers with precision class up to 0.2 at the industrial frequency (50 Hz or 60 Hz. The device is suitable for on-site testing due to its high accuracy, simple structure and low-cost hardware.

  20. Photostress Testing Device for Diagnosing Retinal Disease

    OpenAIRE

    Elizabeth Swan; Jim Schwiegerling; Gholam Peyman; Eniko Enikov

    2014-01-01

    Retinal diseases such as Age-Related Macular Degeneration (ARMD) affect nearly one in three elderly patients. ARMD damages the central vision photoreceptors in the fovea. The Photostress Test is a simple technique for testing for the early effects of ARMD. Here, the illumination sources in a novel self-administered Photostress Testing device were modeled for safety and distribution in illumination software. After satisfying the design constraints in the model, a prototype of the illumination ...

  1. Scheme of Testing Unit for Earth-Point Searching Device in Small-Current Electric Power System%“小电流接地选检装置”的试验装置的设想

    Institute of Scientific and Technical Information of China (English)

    董建民

    2000-01-01

    In the light of elctric power system model,this paper introduces a set of simple available testing unit for searching earthpoint in small-current electric opwwer system and check its operating reliability and accuracy,gives out a basic viewpoint for choosing a a set of earth-point searching device.%从模拟电力系统的角度出发,提出建立一套简单易行的小电流接地选线装置的测试装置,以对选线装置动作的准确性进行校验,为选线装置的选型奠定基础

  2. Field testing driver night vision devices

    NARCIS (Netherlands)

    Kooi, F.L.; Kolletzki, D.

    2007-01-01

    This paper summarizes the available methodologies to field test driver night vision devices ranging from vehicle mounted camera’s to head-mounted NVG’s. As in flight trials, a formidable challenge is to collect meaningful performance measures. Night vision systems for land and air systems show many

  3. Ultrasonic fatigue testing device under biaxial bending

    Directory of Open Access Journals (Sweden)

    C. Brugger

    2016-07-01

    Full Text Available A new fatigue testing device has been developed to test specimens under biaxial loading at 20 kHz. A flat smooth specimen with a disc geometry is placed on a torus frame and cyclically loaded at the center of its upper face. Disc bending generates a biaxial proportional stress state at the center of the lower face. Any positive loading ratio can be applied. A cast aluminum alloy (used to produce cylinder heads has been tested under biaxial bending using this device in order to determine its fatigue strength at 109 cycles under high hydrostatic pressure. Self-heating is moderate but macroscopic fatigue cracks after testing are very long. First results in VHCF regime are consistent with literature results obtained under similar stress state but in HCF regime and at 20 Hz.

  4. Photostress Testing Device for Diagnosing Retinal Disease

    Directory of Open Access Journals (Sweden)

    Elizabeth Swan

    2014-08-01

    Full Text Available Retinal diseases such as Age-Related Macular Degeneration (ARMD affect nearly one in three elderly patients. ARMD damages the central vision photoreceptors in the fovea. The Photostress Test is a simple technique for testing for the early effects of ARMD. Here, the illumination sources in a novel self-administered Photostress Testing device were modeled for safety and distribution in illumination software. After satisfying the design constraints in the model, a prototype of the illumination system was fabricated and tested to confirm the modeling results. The resultant prototype can be used to aid in the diagnosis of retinal disease and is well within retinal safety levels.

  5. Electrostatic discharge testing of electroexplosive devices

    Energy Technology Data Exchange (ETDEWEB)

    Hingorani, S.L.

    1990-01-01

    Electrostatic discharge (ESD) testing of electroexplosive devices has previously been regarded as single pulse, go/no-go testing, the emphasis being on the safety of the devices when exposed to human handling. For some components it has been found to be a destructive test; for others the test is performed 100% in production product-acceptance testing and is considered a nondestructive and nondegrading test if the component does not fire. Recent studies performed by R. J. Fisher at Sandia have resulted in a new model of the worst case human body electrostatic discharge that is more accurate than the model that is currently in use for testing electroexplosive components. In addition, recent requirements for no degradation or loss of reliability after multiple exposures (up to 100) have changed the go/no-go nature of the test. Several components have been tested to the new ESD model; results regarding both safety and reliability will be presented and discussed. 9 refs., 7 figs., 2 tabs.

  6. United States nuclear tests, July 1945 through September 1992

    Energy Technology Data Exchange (ETDEWEB)

    1994-12-01

    This document lists chronologically and alphabetically by name all nuclear tests and simultaneous detonations conducted by the United States from July 1945 through September 1992. Several tests conducted during Operation Dominic involved missile launches from Johnston Atoll. Several of these missile launches were aborted, resulting in the destruction of the missile and nuclear device either on the pad or in the air.

  7. Testing Framework for Mobile Device Forensics Tools

    Directory of Open Access Journals (Sweden)

    Maxwell Anobah

    2014-09-01

    Full Text Available The proliferation of mobile communication and computing devices, in particular smart mobile phones, is almost paralleled with the increasing number of mobile device forensics tools in the market. Each mobile forensics tool vendor, on one hand claims to have a tool that is best in terms of performance, while on the other hand each tool vendor seems to be using different standards for testing their tools and thereby defining what support means differently. To overcome this problem, a testing framework based on a series of tests ranging from basic forensics tasks such as file system reconstruction up to more complex ones countering antiforensic techniques is proposed. The framework, which is an extension of an existing effort done in 2010, prescribes a method to clearly circumscribe the term support into precise levels. It also gives an idea of the standard to be developed and accepted by the forensic community that will make it easier for forensics investigators to quickly select the most appropriate tool for a particular mobile device.

  8. A novel implantable electromechanical ventricular assist device - First acute animal testing

    NARCIS (Netherlands)

    Kaufmann, R; Rakhorst, G; Mihaylov, D; Elstrodt, J; Nix, C; Reul, H; Rau, G

    1997-01-01

    A novel ventricular assist device (HIA-EMLVAD-AT1, Helmholtz Institute Aachen-electromechanical Left Ventricular Assist Device-Animal Test Version 1), driven by a uniformly and unidirectionally rotating actuator and a patented hypocycloidic pusherplate displacement gear unit, was developed and teste

  9. Test device for measuring permeability of a barrier material

    Science.gov (United States)

    Reese, Matthew; Dameron, Arrelaine; Kempe, Michael

    2014-03-04

    A test device for measuring permeability of a barrier material. An exemplary device comprises a test card having a thin-film conductor-pattern formed thereon and an edge seal which seals the test card to the barrier material. Another exemplary embodiment is an electrical calcium test device comprising: a test card an impermeable spacer, an edge seal which seals the test card to the spacer and an edge seal which seals the spacer to the barrier material.

  10. Quick setup of unit test for accelerator controls system

    Energy Technology Data Exchange (ETDEWEB)

    Fu, W.; D' Ottavio, T.; Gassner, D.; Nemesure, S.; Morris, J.

    2011-03-28

    Testing a single hardware unit of an accelerator control system often requires the setup of a program with graphical user interface. Developing a dedicated application for a specific hardware unit test could be time consuming and the application may become obsolete after the unit tests. This paper documents a methodology for quick design and setup of an interface focused on performing unit tests of accelerator equipment with minimum programming work. The method has three components. The first is a generic accelerator device object (ADO) manager which can be used to setup, store, and log testing controls parameters for any unit testing system. The second involves the design of a TAPE (Tool for Automated Procedure Execution) sequence file that specifies and implements all te testing and control logic. The sting third is the design of a PET (parameter editing tool) page that provides the unit tester with all the necessary control parameters required for testing. This approach has been used for testing the horizontal plane of the Stochastic Cooling Motion Control System at RHIC.

  11. Practical unit testing with JUnit and Mockito

    CERN Document Server

    Kaczanowski, Tomek

    2013-01-01

    This book explains in detail how to implement unit tests using two very popular open source Java technologies: JUnit and Mockito. It presents a range of techniques necessary to write high quality unit tests - e.g. mocks, parametrized tests and matchers. It also discusses trade-offs related to the choices we have to make when dealing with some real-life code issues. The book stresses the importance of writing readable and maintainable unit tests, and puts a lot of stress on code quality. It shows how to achieve testable code and to eliminate common mistakes by following the Test Driven Development approach. Every topic discussed in the book is illustrated with code examples, and each chapter is accompanied by some exercises. By reading this book you will: Grasp the role and purpose of unit tests Write high-quality, readable and maintainable unit tests Learn how to use JUnit and Mockito (but also other useful tools) Avoid common pitfalls when writing unit tests Recognize bad unit tests, a...

  12. Hacking and penetration testing with low power devices

    CERN Document Server

    Polstra, Philip

    2014-01-01

    Hacking and Penetration Testing with Low Power Devices shows you how to perform penetration tests using small, low-powered devices that are easily hidden and may be battery-powered. It shows how to use an army of devices, costing less than you might spend on a laptop, from distances of a mile or more. Hacking and Penetration Testing with Low Power Devices shows how to use devices running a version of The Deck, a full-featured penetration testing and forensics Linux distribution, and can run for days or weeks on batteries due to their low power consumption. Author Philip Polstra shows how to

  13. Round robin performance testing of organic photovoltaic devices

    DEFF Research Database (Denmark)

    Gevorgyan, Suren; Zubillaga, Oihana; de Seoane, José María Vega

    2014-01-01

    This study addresses the issue of poor intercomparability of measurements of organic photovoltaic (OPV) devices among different laboratories. We present a round robin performance testing of novel OPV devices among 16 laboratories, organized within the framework of European Research Infrastructure...

  14. Vertical Drop Testing and Simulation of Anthropomorphic Test Devices

    Science.gov (United States)

    Polanco, Michael A.; Littell, Justin D.

    2011-01-01

    A series of 14 vertical impact tests were conducted using Hybrid III 50th Percentile and Hybrid II 50th Percentile Anthropomorphic Test Devices (ATDs) at NASA Langley Research Center. The purpose of conducting these tests was threefold: to compare and contrast the impact responses of Hybrid II and Hybrid III ATDs under two different loading conditions, to compare the impact responses of the Hybrid III configured with a nominal curved lumbar spine to that of a Hybrid III configured with a straight lumbar spine, and to generate data for comparison with predicted responses from two commercially available ATD finite element models. The two loading conditions examined were a high magnitude, short duration acceleration pulse, and a low magnitude, long duration acceleration pulse, each created by using different paper honeycomb blocks as pulse shape generators in the drop tower. The test results show that the Hybrid III results differ from the Hybrid II results more for the high magnitude, short duration pulse case. The comparison of the lumbar loads for each ATD configuration show drastic differences in the loads seen in the spine. The analytical results show major differences between the responses of the two finite element models. A detailed discussion of possible sources of the discrepancies between the two analytical models is also provided.

  15. TVWS devices spectrum mask test and analysis

    CSIR Research Space (South Africa)

    Lamola, MM

    2016-09-01

    Full Text Available White Spaces (TVWS) regulation in the USA and Europe allows channels 21 through 48 in the Ultra high frequency (UHF) band (SA channel) to be used but our device works from channel 29 to 39 corresponding to frequencies from 534 MHz to 622 MHz...-conversion of 1872 MHZ and converts 2.4 GHz channels 1 to 14 (2412 to 2484 MHZ) to 540 to 612 MHz. IV. MEASUREMENTS AND PROCEDURES With the devices and tools stated in the previous section we were able to control the TVWS card and measure the output signal...

  16. Four-terminal electrical testing device. [initiator bridgewire resistance

    Science.gov (United States)

    Robinson, Robert L. (Inventor); Graves, Thomas J. (Inventor); Hoffman, William C., III (Inventor)

    1987-01-01

    The invention relates to a four-terminal electrical connector device for testing and measuring unknown resistances of initiators used for starting pyrotechnic events aboard the space shuttle. The testing device minimizes contact resistance degradation effects and so improves the reliability of resistance measurements taken with the device. Separate and independent voltage sensing and current supply circuits each include a pair of socket contacts for mating engagement with the pins of the initiator. The unknown resistance that is measured by the device is the resistance of the bridgewire of the initiator which is required to be between 0.95 and 1.15 ohms.

  17. Comparative studies of hemoperfusion devices. II. Pressure drop and flow uniformity tests.

    Science.gov (United States)

    Cooney, D O; Infantolino, W; Kane, R

    1979-01-01

    One resin-based hemoperfusion device and three charcoal-based hemoperfusion devices were tested to determine their pressure drop and flow uniformity characteristics. Measurements were made on pressure drop versus flow rate using distilled water and on pressure drop versus time using bovine blood. Effluent concentration curves obtained after the step-change introduction of a high molecular weight dye solution to each unit were used to determine the priming volumes of the devices and were interpreted to yield information regarding the uniformities of flow in each device. The pressure drop and priming volume values for the resin-based device were significantly higher than the corresponding values for the charcoal-based units.

  18. Cooling of superconducting devices by liquid storage and refrigeration unit

    Science.gov (United States)

    Laskaris, Evangelos Trifon; Urbahn, John Arthur; Steinbach, Albert Eugene

    2013-08-20

    A system is disclosed for cooling superconducting devices. The system includes a cryogen cooling system configured to be coupled to the superconducting device and to supply cryogen to the device. The system also includes a cryogen storage system configured to supply cryogen to the device. The system further includes flow control valving configured to selectively isolate the cryogen cooling system from the device, thereby directing a flow of cryogen to the device from the cryogen storage system.

  19. Developing an Instrumentation Package for in-Water Testing of Marine Hydrokinetic Energy Devices: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, E.

    2010-08-01

    The ocean-energy industry is still in its infancy and device developers have provided their own equipment and procedures for testing. Currently, no testing standards exist for ocean energy devices in the United States. Furthermore, as prototype devices move from the test tank to in-water testing, the logistical challenges and costs grow exponentially. Development of a common instrumentation package that can be moved from device to device is one means of reducing testing costs and providing normalized data to the industry as a whole. As a first step, the U.S. National Renewable Energy Laboratory (NREL) has initiated an effort to develop an instrumentation package to provide a tool to allow common measurements across various ocean energy devices. The effort is summarized in this paper. First, we present the current status of ocean energy devices. We then review the experiences of the wind industry in its development of the instrumentation package and discuss how they can be applied in the ocean environment. Next, the challenges that will be addressed in the development of the ocean instrumentation package are discussed. For example, the instrument package must be highly adaptable to fit a large array of devices but still conduct common measurements. Finally, some possible system configurations are outlined followed by input from the industry regarding its measurement needs, lessons learned from prior testing, and other ideas.

  20. Single Event Testing on Complex Devices: Test Like You Fly Versus Test-Specific Design Structures

    Science.gov (United States)

    Berg, Melanie D.; Label, Kenneth

    2016-01-01

    We present a mechanism for evaluating complex digital systems targeted for harsh radiation environments such as space. Focus is limited to analyzing the single event upset (SEU) susceptibility of designs implemented inside Field Programmable Gate Array (FPGA) devices. Tradeoffs are provided between application-specific versus test-specific test structures.

  1. Single Event Testing on Complex Devices: Test Like You Fly versus Test-Specific Design Structures

    Science.gov (United States)

    Berg, Melanie; LaBel, Kenneth A.

    2014-01-01

    We present a framework for evaluating complex digital systems targeted for harsh radiation environments such as space. Focus is limited to analyzing the single event upset (SEU) susceptibility of designs implemented inside Field Programmable Gate Array (FPGA) devices. Tradeoffs are provided between application-specific versus test-specific test structures.

  2. INTERFACE DEVICE FOR NONDESTRUCTIVE TESTING OF RESIDUAL SURFACE STRESSES

    Directory of Open Access Journals (Sweden)

    Gennady A. Perepelkin

    2016-01-01

    Full Text Available The paper considers the organization of connection of a personal computer with a device for nondestructive testing of residual surface stresses. The device works is based on the phenomenon of diffraction of ionizing radiation from the crystal lattice near the surface of the crystallites. Proposed software interface to the organization for each type of user: the device developers, administrators, users. Some aspects of the organization of communication microcontroller to a PC via USB-port

  3. Subscale Test Methods for Combustion Devices

    Science.gov (United States)

    Anderson, W. E.; Sisco, J. C.; Long, M. R.; Sung, I.-K.

    2005-01-01

    Stated goals for long-life LRE s have been between 100 and 500 cycles: 1) Inherent technical difficulty of accurately defining the transient and steady state thermochemical environments and structural response (strain); 2) Limited statistical basis on failure mechanisms and effects of design and operational variability; and 3) Very high test costs and budget-driven need to protect test hardware (aversion to test-to-failure). Ambitious goals will require development of new databases: a) Advanced materials, e.g., tailored composites with virtually unlimited property variations; b) Innovative functional designs to exploit full capabilities of advanced materials; and c) Different cycles/operations. Subscale testing is one way to address technical and budget challenges: 1) Prototype subscale combustors exposed to controlled simulated conditions; 2) Complementary to conventional laboratory specimen database development; 3) Instrumented with sensors to measure thermostructural response; and 4) Coupled with analysis

  4. Software test attacks to break mobile and embedded devices

    CERN Document Server

    Hagar, Jon Duncan

    2013-01-01

    Address Errors before Users Find Them Using a mix-and-match approach, Software Test Attacks to Break Mobile and Embedded Devices presents an attack basis for testing mobile and embedded systems. Designed for testers working in the ever-expanding world of ""smart"" devices driven by software, the book focuses on attack-based testing that can be used by individuals and teams. The numerous test attacks show you when a software product does not work (i.e., has bugs) and provide you with information about the software product under test. The book guides you step by step starting with the basics. It

  5. Electrode holder useful in a corrosion testing device

    Science.gov (United States)

    Murphy, Jr., Robert J.; Jamison, Dale E.

    1986-01-01

    The present invention is directed to an apparatus and method for holding one or more test electrodes of precisely known exposed surface area. The present invention is particularly useful in a device for determining the corrosion properties of the materials from which the test electrodes have been formed. The present invention relates to a device and method for holding the described electrodes wherein the exposed surface area of the electrodes is only infinitesimally decreased. Further, in the present invention the exposed, electrically conductive surface area of the contact devices is small relative to the test electrode surface area. The holder of the present invention conveniently comprises a device for contacting and engaging each test electrode at two point contacts infinitesimally small in relation to the exposed surface area of the electrodes.

  6. Micro-Combined Heat and Power Device Test Facility

    Data.gov (United States)

    Federal Laboratory Consortium — NIST has developed a test facility for micro-combined heat and power (micro-CHP) devices to measure their performance over a range of different operating strategies...

  7. Accelerated life testing and temperature dependence of device characteristics in GaAs CHFET devices

    Science.gov (United States)

    Gallegos, M.; Leon, R.; Vu, D. T.; Okuno, J.; Johnson, A. S.

    2002-01-01

    Accelerated life testing of GaAs complementary heterojunction field effect transistors (CHFET) was carried out. Temperature dependence of single and synchronous rectifier CHFET device characteristics were also obtained.

  8. Testing Quantum Devices: Practical Entanglement Verification in Bipartite Optical Systems

    OpenAIRE

    Häseler, Hauke; Moroder, Tobias; Lütkenhaus, Norbert

    2007-01-01

    We present a method to test quantum behavior of quantum information processing devices, such as quantum memories, teleportation devices, channels and quantum key distribution protocols. The test of quantum behavior can be phrased as the verification of effective entanglement. Necessary separability criteria are formulated in terms of a matrix of expectation values in conjunction with the partial transposition map. Our method is designed to reduce the resources for entanglement verification. A...

  9. Study of the in vitro cytotoxicity testing of medical devices.

    Science.gov (United States)

    Li, Weijia; Zhou, Jing; Xu, Yuyin

    2015-09-01

    The cytotoxicity test is one of the biological evaluation and screening tests that use tissue cells in vitro to observe the cell growth, reproduction and morphological effects by medical devices. Cytotoxicity is preferred as a pilot project test and an important indicator for toxicity evaluation of medical devices as it is simple, fast, has a high sensitivity and can save animals from toxicity. Three types of cytotoxicity test are stated in the International Organization for Standardization 109993-5: Extract, direct contact and indirect contact tests. The xCELLigence real-time cell analysis system shows a significant potential in regards to cytotoxicity in recent years. The present review provides a brief insight into the in vitro cytotoxicity testing of medical devices.

  10. Future opportunities for advancing glucose test device electronics.

    Science.gov (United States)

    Young, Brian R; Young, Teresa L; Joyce, Margaret K; Kennedy, Spencer I; Atashbar, Massood Z

    2011-09-01

    Advancements in the field of printed electronics can be applied to the field of diabetes testing. A brief history and some new developments in printed electronics components applicable to personal test devices, including circuitry, batteries, transmission devices, displays, and sensors, are presented. Low-cost, thin, and lightweight materials containing printed circuits with energy storage or harvest capability and reactive/display centers, made using new printing/imaging technologies, are ideal for incorporation into personal-use medical devices such as glucose test meters. Semicontinuous rotogravure printing, which utilizes flexible substrates and polymeric, metallic, and/or nano "ink" composite materials to effect rapidly produced, lower-cost printed electronics, is showing promise. Continuing research advancing substrate, "ink," and continuous processing development presents the opportunity for research collaboration with medical device designers.

  11. Devices for fatigue testing of electroplated nickel (MEMS)

    DEFF Research Database (Denmark)

    Larsen, Kristian Pontoppidan; Ravnkilde, J. T.; Ginnerup, Morten;

    2002-01-01

    In-situ fatigue test devices with integrated electrostatic actuator were fabricated in electroplated nanocrystalline nickel (nano-nickel). The devices feature in-plane approximately pure bending with fixed displacement of the test specimen of the dimensions: widths from 2μm to 3.7μm, a height of 7......μm and an effective length from 4μm to 27μm. Maximum stresses of the test beam were calculated to be 500MPa to 2100MPa by use of FEM tools. The test results indicate very promising fatigue properties of nano-nickel, as none of the test devices have shown fatigue failure or even initiation of cracks...

  12. Design and test of a flywheel energy storage unit for spacecraft application

    Science.gov (United States)

    Cormack, A., III; Notti, J. E., Jr.; Ruiz, M. L.

    1975-01-01

    This paper summarizes the design and test of a development flywheel energy storage device intended for spacecraft application. The flywheel unit is the prototype for the rotating assembly portion of an Integrated Power and Attitude Control System (IPACS). The paper includes a general description of the flywheel unit; specific design characteristics for the rotor and bearings, motor-generators, and electronics; an efficiency analysis; and test results for a research unit.

  13. Evaluation of a pulsed xenon ultraviolet light device for isolation room disinfection in a United Kingdom hospital.

    Science.gov (United States)

    Hosein, Ian; Madeloso, Rosie; Nagaratnam, Wijayaratnam; Villamaria, Frank; Stock, Eileen; Jinadatha, Chetan

    2016-09-01

    Pathogen transmission from contaminated surfaces can cause hospital-associated infections. Although pulsed xenon ultraviolet (PX-UV) light devices have been shown to decrease hospital room bioburden in the United States, their effectiveness in United Kingdom (UK) hospitals is less understood. Forty isolation rooms at the Queens Hospital (700 beds) in North London, UK, were sampled for aerobic bacteria after patient discharge, after manual cleaning with a hypochlorous acid-troclosene sodium solution, and after PX-UV disinfection. PX-UV device efficacy on known organisms was tested by exposing inoculated agar plates in a nonpatient care area. Turnaround times for device usage were recorded, and a survey of hospital staff for perceptions of the device was undertaken. After PX-UV disinfection, the bacterial contamination measured in colony forming units (CFU) decreased by 78.4%, a 91% reduction from initial bioburden levels prior to terminal cleaning. PX-UV exposure resulted in a 5-log CFU reduction for multidrug-resistant organisms (MDROs) on spiked plates. The average device turnaround time was 1 hour, with minimal impact on patient throughput. Ward staff were enthusiastic about device deployment, and device operators reported physical comfort in usage. PX-UV use decreased bioburden in patient discharge rooms and on agar plates spiked with MDROs. The implementation of the PX-UV device was well received by hospital cleaning and ward staff, with minimal disruption to patient flow. Copyright © 2016 Association for Professionals in Infection Control and Epidemiology, Inc. All rights reserved.

  14. X-Ray-Diffraction Tests Of Irradiated Electronic Devices: I

    Science.gov (United States)

    Shaw, David C.; Lowry, Lynn E.; Barnes, Charles E.

    1993-01-01

    X-ray-diffraction tests performed on aluminum conductors in commercial HI1-507A complementary metal oxide/semiconductor (CMOS) integrated-circuit analog multiplexers, both before and after circuits exposed to ionizing radiation from Co(60) source, and after postirradiation annealing at ambient and elevated temperatures. Tests in addition to electrical tests performed to determine effects of irradiation and of postirradiation annealing on electrical operating characteristics of circuits. Investigators sought to determine whether relationship between effects of irradiation on devices and physical stresses within devices. X-ray diffraction potentially useful for nondestructive measurement of stresses.

  15. Research of in—service sipping test device

    Institute of Scientific and Technical Information of China (English)

    DengJun-Xian; XuYu-Ming; 等

    1998-01-01

    Sipping test device is used to identify the tightness of the irradiated fuel assembly during refuelling campaign.The gas is selected as the medium and the xenon-133 as the indicating nuclide,The device consists of the gas system,the γ-activity detection and measurement system,the power supply and signal system,the mechanical components and parts.The device has satisfactory functions,e.g.easy operation,indication in instrumentation,chart record and acoustic alarm,which can meet the operation demand of the nuclear reactor.

  16. Reproduction of Realistic Background Noise for Testing Telecommunications Devices

    DEFF Research Database (Denmark)

    Gil Corrales, Juan David; Song, Wookeun; MacDonald, Ewen

    2015-01-01

    A method for reproduction of sound, based on crosstalk cancellation using inverse filters, was implemented in the context of testing telecommunications devices. The effect of the regularization parameter, number of loudspeakers, type of background noise, and a technique to attenuate audible...... artifacts, were investigated. The quality of the reproduced sound was evaluated both objectively and subjectively with respect to the reference sounds, at points where telecommunications devices would be potentially placed around the head. The highest regularization value gave the best results...

  17. Control device for underground extension units. Steuereinrichtung fuer untertaegige Ausbaueinheiten

    Energy Technology Data Exchange (ETDEWEB)

    Peters, B.; Rosenberg, H.; Weirich, W.

    1987-08-20

    The invention concerns a control device for a sliding cap situated on the screwdown cap of an extension frame. The control device situated in the area of the joint axis between the screwdown cap and the roof cap consists of a cylindrical gear-shifting gate and a proximity switch. The control device prevents the sliding cap moving out if a certain angle of the screwdown cap is exceeded.

  18. New Design of Blade Untwisting Device of Cyclone Unit

    Directory of Open Access Journals (Sweden)

    D. I. Misiulia

    2010-01-01

    Full Text Available The paper presents a new design of a blade untwisting device where blades are considered as a main element of the device. A profile of the blades corresponds to a circular arch. An inlet angle of  the blades is determined by stream aerodynamics in an exhaust pipe, and an exit angle is determined by rectilinear gas motion. Optimum geometrical parameters of the untwisting device have been determined and its application allows to reduce a pressure drop in the ЦН-15 cyclones by 28–30 % while screw-blade untwisting device recovers only 19–20 % of energy.

  19. Unit testing, model validation, and biological simulation

    Science.gov (United States)

    Watts, Mark D.; Ghayoomie, S. Vahid; Larson, Stephen D.; Gerkin, Richard C.

    2016-01-01

    The growth of the software industry has gone hand in hand with the development of tools and cultural practices for ensuring the reliability of complex pieces of software. These tools and practices are now acknowledged to be essential to the management of modern software. As computational models and methods have become increasingly common in the biological sciences, it is important to examine how these practices can accelerate biological software development and improve research quality. In this article, we give a focused case study of our experience with the practices of unit testing and test-driven development in OpenWorm, an open-science project aimed at modeling Caenorhabditis elegans. We identify and discuss the challenges of incorporating test-driven development into a heterogeneous, data-driven project, as well as the role of model validation tests, a category of tests unique to software which expresses scientific models. PMID:27635225

  20. Development of a compact wearable pneumatic drive unit for a ventricular assist device.

    Science.gov (United States)

    Homma, Akihiko; Taenaka, Yoshiyuki; Tatsumi, Eisuke; Akagawa, Eiki; Lee, Hwansung; Nishinaka, Tomohiro; Takewa, Yoshiaki; Mizuno, Toshihide; Tsukiya, Tomonori; Kakuta, Yukihide; Katagiri, Nobumasa; Shimosaki, Isao; Hamada, Shigeru; Mukaibayashi, Hiroshi; Iwaoka, Wataru

    2008-01-01

    The purpose of this study was to develop a compact wearable pneumatic drive unit for a ventricular assist device (VAD). This newly developed drive unit, 20 x 8.5 x 20 cm in size and weighing approximately 1.8 kg, consists of a brushless DC motor, noncircular gears, a crankshaft, a cylinder-piston, and air pressure regulation valves. The driving air pressure is generated by the reciprocating motion of the piston and is controlled by the air pressure regulation valves. The systolic ratio is determined by the noncircular gears, and so is fixed for a given configuration. As a result of an overflow-type mock circulation test, a drive unit with a 44% systolic ratio connected to a Toyobo VAD blood pump with a 70-ml stroke volume achieved a pump output of more than 7 l/min at 100 bpm against a 120 mmHg afterload. Long-term animal tests were also performed using drive units with systolic ratios of 45% and 53% in two Holstein calves weighing 62 kg and 74 kg; the tests were terminated on days 30 and 39, respectively, without any malfunction. The mean aortic pressure, bypass flow, and power consumption for the first calf were maintained at 90 x 13 mmHg, 3.9 x 0.9 l/min, and 12 x 1 W, and those for the second calf were maintained at 88 x 13 mmHg, 5.0 x 0.5 l/min, and 16 x 2 W, respectively. These results indicate that the newly developed drive unit may be used as a wearable pneumatic drive unit for the Toyobo VAD blood pump.

  1. Abrasion Testing of Critical Components of Hydrokinetic Devices

    Energy Technology Data Exchange (ETDEWEB)

    Worthington, Monty [ORPC Alaska; Ali, Muhammad [Ohio University; Ravens, Tom [University of Alaska Anchorage

    2013-12-06

    The objective of the Abrasion Testing of Critical Components of Hydrokinetic Devices (Project) was to test critical components of hydrokinetic devices in waters with high levels of suspended sediment – information that is widely applicable to the hydrokinetic industry. Tidal and river sites in Alaska typically have high suspended sediment concentrations. High suspended sediment also occurs in major rivers and estuaries throughout the world and throughout high latitude locations where glacial inputs introduce silt into water bodies. In assessing the vulnerability of technology components to sediment induced abrasion, one of the greatest concerns is the impact that the sediment may have on device components such as bearings and seals, failures of which could lead to both efficiency loss and catastrophic system failures.

  2. Unit Test Frameworks Tools for High-Quality Software Development

    CERN Document Server

    Hamill, Paul

    2009-01-01

    This is the only book to explore unit testing as a language-independent, standalone development methodology. It covers the theory and methodology of unit test frameworks, offers instruction in unit test development, provides useful code examples in both Java and C++, and details the most commonly used frameworks from the XUnit family, including JUnit for Java, CppUnit for C++, and NUnit for .NET. It also includes the complete source code for CppUnit for C++ and NUnit for .NET.

  3. Consensus stability testing protocols for organic photovoltaic materials and devices

    DEFF Research Database (Denmark)

    Reese, Matthew O.; Gevorgyan, Suren; Jørgensen, Mikkel

    2011-01-01

    Procedures for testing organic solar cell devices and modules with respect to stability and operational lifetime are described. The descriptions represent a consensus of the discussion and conclusions reached during the first 3 years of the international summit on OPV stability (ISOS). The proced...

  4. X-Ray-Diffraction Tests Of Irradiated Electronic Devices: II

    Science.gov (United States)

    Shaw, David C.; Lowry, Lynn E.; Barnes, Charles E.

    1993-01-01

    Report describes research on use of x-ray diffraction to measure stresses in metal conductors of complementary metal oxide/semiconductor (CMOS) integrated circuits exposed to ionizing radiation. Expanding upon report summarized in "X-Ray-Diffraction Tests Of Irradiated Electronic Devices: I" (NPO-18803), presenting data further suggesting relationship between electrical performances of circuits and stresses and strains in metal conductors.

  5. Consensus stability testing protocols for organic photovoltaic materials and devices

    NARCIS (Netherlands)

    Reese, M.O.; Gevorgyan, S.A.; Jørgensen, M.; Bundgaard, E.; Kurtz, S.R.; Ginley, D.S.; Olson, D.C.; Lloyd, M.T.; Morvillo, P.; Katz, E.A.; Elschner, A.; Haillant, O.; Currier, T.R.; Shrotriya, V.; Hermenau, M.; Riede, M.; Kirov, K.R.; Trimmel, G.; Rath, T.; Inganäs, O.; Zhang, F.; Andersson, M.; Tvingstedt, K.; Lira-Cantu, M.; Laird, D.; McGuiness, C.; Gowrisanker, S.; Pannone, M.; Xiao, M.; Hauch, J.; Steim, R.; Delongchamp, D.M.; Rösch, R.; Hoppe, H.; Espinosa, N.; Urbina, A.; Yaman-Uzunoglu, G.; Bonekamp, J.-B.; Breemen, A.J.J.M. van; Girotto, C.; Voroshazi, E.; Krebs, F.C.

    2011-01-01

    Procedures for testing organic solar cell devices and modules with respect to stability and operational lifetime are described. The descriptions represent a consensus of the discussion and conclusions reached during the first 3 years of the international summit on OPV stability (ISOS). The procedure

  6. Medical Device Regulation: A Comparison of the United States and the European Union.

    Science.gov (United States)

    Maak, Travis G; Wylie, James D

    2016-08-01

    Medical device regulation is a controversial topic in both the United States and the European Union. Many physicians and innovators in the United States cite a restrictive US FDA regulatory process as the reason for earlier and more rapid clinical advances in Europe. The FDA approval process mandates that a device be proved efficacious compared with a control or be substantially equivalent to a predicate device, whereas the European Union approval process mandates that the device perform its intended function. Stringent, peer-reviewed safety data have not been reported. However, after recent high-profile device failures, political pressure in both the United States and the European Union has favored more restrictive approval processes. Substantial reforms of the European Union process within the next 5 to 10 years will result in a more stringent approach to device regulation, similar to that of the FDA. Changes in the FDA regulatory process have been suggested but are not imminent.

  7. Sipping test update device for fuel elements cladding inspections in IPR-r1 TRIGA reactor

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, R.R.; Mesquita, A.Z.; Andrade, E.P.D.; Gual, Maritza R., E-mail: rrr@cdtn.br, E-mail: amir@cdtn.br, E-mail: edson@cdtn.br, E-mail: maritzargual@gmail.com [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2015-07-01

    It is in progress at the Centro de Desenvolvimento da Tecnologia Nuclear - CDTN (Nuclear Technology Development Center), a research project that aims to investigate possible leaks in the fuel elements of the TRIGA reactor, located in this research center. This paper presents the final form of sipping test device for TRIGA reactor, and results of the first experiments setup. Mechanical support strength tests were made by knotting device on the crane, charged with water from the conventional water supply, and tests outside the reactor pool with the use of new non-irradiated fuel elements encapsulated in stainless steel, and available safe stored in this unit. It is expected that tests with graphite elements from reactor pool are done soon after and also the test experiment with the first fuel elements in service positioned in the B ring (central ring) of the reactor core in the coming months. (author)

  8. Standard practice for torque calibration of testing machines and devices

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2009-01-01

    1.1 This practice covers procedures and requirements for the calibration of torque for static and quasi-static torque capable testing machines or devices. These may, or may not, have torque indicating systems and include those devices used for the calibration of hand torque tools. Testing machines may be calibrated by one of the three following methods or combination thereof: 1.1.1 Use of standard weights and lever arms. 1.1.2 Use of elastic torque measuring devices. 1.1.3 Use of elastic force measuring devices and lever arms. 1.1.4 Any of the methods require a specific uncertainty of measurement and a traceability derived from national standards of mass and length. 1.2 The procedures of 1.1.1, 1.1.2, and 1.1.3 apply to the calibration of the torque-indicating systems associated with the testing machine, such as a scale, dial, marked or unmarked recorder chart, digital display, etc. In all cases the buyer/owner/user must designate the torque-indicating system(s) to be calibrated and included in the repor...

  9. Biaxial testing for fabrics and foils optimizing devices and procedures

    CERN Document Server

    Beccarelli, Paolo

    2015-01-01

    This book offers a well-structured, critical review of current design practice for tensioned membrane structures, including a detailed analysis of the experimental data required and critical issues relating to the lack of a set of design codes and testing procedures. The technical requirements for biaxial testing equipment are analyzed in detail, and aspects that need to be considered when developing biaxial testing procedures are emphasized. The analysis is supported by the results of a round-robin exercise comparing biaxial testing machines that involved four of the main research laboratories in the field. The biaxial testing devices and procedures presently used in Europe are extensively discussed, and information is provided on the design and implementation of a biaxial testing rig for architectural fabrics at Politecnico di Milano, which represents a benchmark in the field. The significance of the most recent developments in biaxial testing is also explored.

  10. Single Event Effect Testing of the Analog Devices ADV212

    Science.gov (United States)

    Wilcox, Ted; Campola, Michael; Kadari, Madhu; Nadendla, Seshagiri R.

    2017-01-01

    The Analog Devices ADV212 was initially tested for single event effects (SEE) at the Texas AM University Cyclotron Facility (TAMU) in July of 2013. Testing revealed a sensitivity to device hang-ups classified as single event functional interrupts (SEFI), soft data errors classified as single event upsets (SEU), and, of particular concern, single event latch-ups (SEL). All error types occurred so frequently as to make accurate measurements of the exposure time, and thus total particle fluence, challenging. To mitigate some of the risk posed by single event latch-ups, circuitry was added to the electrical design to detect a high current event and automatically recycle power and reboot the device. An additional heavy-ion test was scheduled to validate the operation of the recovery circuitry and the continuing functionality of the ADV212 after a substantial number of latch-up events. As a secondary goal, more precise data would be gathered by an improved test method, described in this test report.

  11. Analytical evaluation of five oral fluid drug testing devices

    OpenAIRE

    Isalberti, Cristina; Van Stechelman, Sylvie; Legrand, Sara-Ann; Van der Linden, Gertrude; Verstraete, Alain

    2010-01-01

    Introduction: The correlation with blood drug presence and the easiness of sample collection make oral fluid an ideal matrix for roadside drug tests targeting impaired drivers. Aim: To evaluate the reliability of five oral fluid testing devices: Varian OraLab®6, Dräger DrugTest® 5000, Cozart® DDS 806, Mavand RapidSTAT® and Innovacon OrAlert. Method: More than 760 samples were collected from volunteers either at drug addiction treatment centres or during roadside sessions. Target drug ...

  12. Development of a Wearable Device for Motion Capturing Based on Magnetic and Inertial Measurement Units

    Directory of Open Access Journals (Sweden)

    Bin Fang

    2017-01-01

    Full Text Available This paper presents a novel wearable device for gesture capturing based on inertial and magnetic measurement units that are made up of micromachined gyroscopes, accelerometers, and magnetometers. The low-cost inertial and magnetic measurement unit is compact and small enough to wear and there are altogether thirty-six units integrated in the device. The device is composed of two symmetric parts, and either the right part or the left one contains eighteen units covering all the segments of the arm, palm, and fingers. The offline calibration and online calibration are proposed to improve the accuracy of sensors. Multiple quaternion-based extended Kalman filters are designed to estimate the absolute orientations, and kinematic models of the arm-hand are considered to determine the relative orientations. Furthermore, position algorithm is deduced to compute the positions of corresponding joint. Finally, several experiments are implemented to verify the effectiveness of the proposed wearable device.

  13. Device-independent parallel self-testing of two singlets

    Science.gov (United States)

    Wu, Xingyao; Bancal, Jean-Daniel; McKague, Matthew; Scarani, Valerio

    2016-06-01

    Device-independent self-testing offers the possibility of certifying the quantum state and measurements, up to local isometries, using only the statistics observed by querying uncharacterized local devices. In this paper we study parallel self-testing of two maximally entangled pairs of qubits; in particular, the local tensor product structure is not assumed but derived. We prove two criteria that achieve the desired result: a double use of the Clauser-Horne-Shimony-Holt inequality and the 3 ×3 magic square game. This demonstrate that the magic square game can only be perfectly won by measuring a two-singlet state. The tolerance to noise is well within reach of state-of-the-art experiments.

  14. CERN tests reveal security flaws with industrial network devices

    CERN Document Server

    Lüders, Stefan

    2006-01-01

    The CERN high energy particle physics facility at Geneva, Switzerland will incorporate a wide range of COTS industrial control systems within its next generation particle collider, the LHC. In particular, the Internet will be used to facilitate the remote access for accelerator and particle physicists and system experts based at several hundred locations around the globe. The integration of Industrial Ethernet and COTS PLCs within the LHC program focuses extreme attention on the industrial network cyber-security requirement. CERN's response has been to conduct operational research on the security resilience of networked industrial devices. As test team lead Stefan Lüders reports here, industrial networked devices put through the organisation's test procedures have generally shown up unexpected vulnerabilities.

  15. Overcoming the Challenges of Conducting Early Feasibility Studies of Medical Devices in the United States.

    Science.gov (United States)

    Holmes, David R; Califf, Robert; Farb, Andrew; Abel, Dorothy; Mack, Michael; Syrek Jensen, Tamara; Zuckerman, Bram; Leon, Martin; Shuren, Jeff

    2016-10-25

    Initial clinical studies of new medical technologies involve a complex balance of research participant benefits versus risks and costs of uncertainty when novel concepts are tested. The Food and Drug Administration Center for Devices and Radiological Health has recently introduced the Early Feasibility Study (EFS) Program for facilitating the conduct of these studies under the Investigational Device Exemption regulations. However, a systematic approach is needed to successfully implement this program while affording appropriate preservation of the rights and interests of patients. For this to succeed, a holistic reform of the clinical studies ecosystem for performing early-stage clinical research in the United States is necessary. The authors review the current landscape of the U.S. EFS and make recommendations for developing an efficient EFS process to meet the goal of improving access to early-stage, potentially beneficial medical devices in the United States.

  16. ENDOXY - Development of a Biomimetic Oxygenator-Test-Device.

    Directory of Open Access Journals (Sweden)

    Maren Dietrich

    Full Text Available This study focusses on the development of a biomimetic oxygenator test device. Due to limited biocompatibility, current oxygenators do not allow mid- to long-term therapy. Tissue engineering uses autologous cell sources to overcome the immunogenic barriers of biomaterials. Surface coating with endothelial cells might improve hemocompatibility and thus prevent immunogenic reactions of the body. In this study this concept is applied to endothelialise a gas-permeable membrane to develop a biomimetic oxygenator test-device (ENDOXY.ENDOXY-a multifunctional test-system was developed to endothelialise a gas-permeable membrane suitable for cell culture and to test the cell retention under shear stress and to measure gas transfer through it.Successful endothelialisation of the membrane was achieved and cells showed characteristic endothelial morphologies. They stained positive for endothelial markers. The number of cells aligned with shear stress and cell retention after blood perfusing experiments was high. Gas transfer is observed via uncoated and endothelialised membranes.The study showed promising results with regard to system design, endothelialisation, and cell retention under shear stress conditions. It strongly encourages further research into the system by testing different membrane materials to design a biomimetic membrane surface and pave way for a fully hemocompatible oxygenator.

  17. Electronic Unit Pump Test Bench Development and Pump Properties Research

    Institute of Scientific and Technical Information of China (English)

    LIU Bo-lan; HUANG Ying; ZHANG Fu-jun; ZHAO Chang-lu

    2006-01-01

    A unit pump test bench is developed on an in-line pump test platform. The bench is composed of pump adapting assembly, fuel supply subsystem, lubricating subsystem and a control unit. A crank angle domain injection control method is given out and the control accuracy can be 0.1° crank degree. The bench can test bot h mechanical unit pump and electronic unit pump. A test model-PLD12 electronic unit pump is tested. Full pump delivery map and some influence factors test is d one. Experimental results show that the injection quantity is linear with the de livery angle. The quantity change rate is 15% when fuel temperature increases 30℃. The delivery quantity per cycle increases 30mg at 28V drive voltage. T he average delivery difference for two same type pumps is 5%. Test results show that the bench can be used for unit pump verification.

  18. Poster Abstract: Automatic Calibration of Device Attitude in Inertial Measurement Unit Based Traffic Probe Vehicles

    KAUST Repository

    Mousa, Mustafa

    2016-04-28

    Probe vehicles consist in mobile traffic sensor networks that evolve with the flow of vehicles, transmitting velocity and position measurements along their path, generated using GPSs. To address the urban positioning issues of GPSs, we propose to replace them with inertial measurement units onboard vehicles, to estimate vehicle location and attitude using inertial data only. While promising, this technology requires one to carefully calibrate the orientation of the device inside the vehicle to be able to process the acceleration and rate gyro data. In this article, we propose a scheme that can perform this calibration automatically by leveraging the kinematic constraints of ground vehicles, and that can be implemented on low-end computational platforms. Preliminary testing shows that the proposed scheme enables one to accurately estimate the actual accelerations and rotation rates in the vehicle coordinates. © 2016 IEEE.

  19. Experimental device-independent tests of classical and quantum entropy

    Science.gov (United States)

    Zhu, Feng; Zhang, Wei; Chen, Sijing; You, Lixing; Wang, Zhen; Huang, Yidong

    2016-12-01

    In quantum information processing, it is important to witness the entropy of the message in the device-independent way which was proposed recently [R. Chaves, J. B. Brask, and N. Brunner, Phys. Rev. Lett. 115, 110501 (2015), 10.1103/PhysRevLett.115.110501]. In this paper, we theoretically obtain the minimal quantum entropy for three widely used linear dimension witnesses, which is considered "a difficult question." Then we experimentally test the classical and quantum entropy in a device-independent manner. The experimental results agree well with the theoretical analysis, demonstrating that entropy is needed in quantum systems that is lower than the entropy needed in classical systems with the given value of the dimension witness.

  20. Experimental device-independent tests of classical and quantum dimensions

    Science.gov (United States)

    Ahrens, Johan; Badziag, Piotr; Cabello, Adán; Bourennane, Mohamed

    2012-08-01

    A fundamental resource in any communication and computation task is the amount of information that can be transmitted and processed. The classical information encoded in a set of states is limited by the number of distinguishable states or classical dimension dc of the set. The sets used in quantum communication and information processing contain states that are neither identical nor distinguishable, and the quantum dimension dq of the set is the dimension of the Hilbert space spanned by these states. An important challenge is to assess the (classical or quantum) dimension of a set of states in a device-independent way, that is, without referring to the internal working of the device generating the states. Here we experimentally test dimension witnesses designed to efficiently determine the minimum dimension of sets of (three or four) photonic states from the correlations originated from measurements on them, and distinguish between classical and quantum sets of states.

  1. Operating room fire prevention: creating an electrosurgical unit fire safety device.

    Science.gov (United States)

    Culp, William C; Kimbrough, Bradly A; Luna, Sarah; Maguddayao, Aris J

    2014-08-01

    To reduce the incidence of surgical fires. Operating room fires represent a potentially life-threatening hazard and are triggered by the electrosurgical unit (ESU) pencil. Carbon dioxide is a fire suppressant and is a routinely used medical gas. We hypothesize that a shroud of protective carbon dioxide covering the tip of the ESU pencil displaces oxygen, thereby preventing fire ignition. Using 3-dimensional modeling techniques, a polymer sleeve was created and attached to an ESU pencil. This sleeve was connected to a carbon dioxide source and directed the gas through multiple precisely angled ports, generating a cone of fire-suppressive carbon dioxide surrounding the active pencil tip. This device was evaluated in a flammability test chamber containing 21%, 50%, and 100% oxygen with sustained ESU activation. The sleeve was tested with and without carbon dioxide (control) until a fuel was ignited or 30 seconds elapsed. Time to ignition was measured by high-speed videography. Fires were ignited with each control trial (15/15 trials). The control group median ± SD ignition time in 21% oxygen was 3.0 ± 2.4 seconds, in 50% oxygen was 0.1 ± 1.8 seconds, and in 100% oxygen was 0.03 ± 0.1 seconds. No fire was observed when the fire safety device was used in all concentrations of oxygen (0/15 trials; P fire ignition was 76% to 100%. A sleeve creating a cone of protective carbon dioxide gas enshrouding the sparks from an ESU pencil effectively prevents fire in a high-flammability model. Clinical application of this device may reduce the incidence of operating room fires.

  2. Tritium Systems Test Assembly: design for major device fabrication review

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, J.L.; Sherman, R.H.

    1977-06-01

    This document has been prepared for the Major Device Fabrication Review for the Tritium Systems Test Assembly (TSTA). The TSTA is dedicated to the development, demonstration, and interfacing of technologies related to the deuterium-tritium fuel cycle for fusion reactor systems. The principal objectives for TSTA are: (a) demonstrate the fuel cycle for fusion reactor systems; (b) develop test and qualify equipment for tritium service in the fusion program; (c) develop and test environmental and personnel protective systems; (d) evaluate long-term reliability of components; (e) demonstrate long-term safe handling of tritium with no major releases or incidents; and (f) investigate and evaluate the response of the fuel cycle and environmental packages to normal, off-normal, and emergency situations. This document presents the current status of a conceptual design and cost estimate for TSTA. The total cost to design, construct, and operate TSTA through FY-1981 is estimated to be approximately $12.2 M.

  3. Method and device for tensile testing of cable bundles

    Science.gov (United States)

    Robertson, Lawrence M; Ardelean, Emil V; Goodding, James C; Babuska, Vit

    2012-10-16

    A standard tensile test device is improved to accurately measure the mechanical properties of stranded cables, ropes, and other composite structures wherein a witness is attached to the top and bottom mounting blocks holding the cable under test. The witness is comprised of two parts: a top and a bottom rod of similar diameter with the bottom rod having a smaller diameter stem on its upper end and the top rod having a hollow opening in its lower end into which the stem fits forming a witness joint. A small gap is present between the top rod and the larger diameter portion of the bottom rod. A standard extensometer is attached to the top and bottom rods of the witness spanning this small witness gap. When a force is applied to separate the mounting blocks, the gap in the witness expands the same length that the entire test specimen is stretched.

  4. A new cryogenic test facility for large superconducting devices at CERN

    CERN Document Server

    Perin, A; Serio, L; Stewart, L; Benda, V; Bremer, J; Pirotte, O

    2015-01-01

    To expand CERN testing capability to superconducting devices that cannot be installed in existing test facilities because of their size and/or mass, CERN is building a new cryogenic test facility for large and heavy devices. The first devices to be tested in the facility will be the S-FRS superconducting magnets for the FAIR project that is currently under construction at the GSI Research Center in Darmstadt, Germany. The facility will include a renovated cold box with 1.2 kW at 4.5 K equivalent power with its compression system, two independent 15 kW liquid nitrogen precooling and warm-up units, as well as a dedicated cryogenic distribution system providing cooling power to three independent test benches. The article presents the main input parameters and constraints used to define the cryogenic system and its infrastructure. The chosen layout and configuration of the facility is presented and the characteristics of the main components are described.

  5. 29 CFR 1919.30 - Examinations subsequent to unit tests.

    Science.gov (United States)

    2010-07-01

    ... Treatment; Competent Persons § 1919.30 Examinations subsequent to unit tests. (a) After satisfactory... deformation or failure. (c) For subsequent tests such parts of the gear shall be dismantled or...

  6. Mastering Unit testing using Mockito and JUnit

    CERN Document Server

    Acharya, Sujoy

    2014-01-01

    A practical and easy-to-follow, yet comprehensive, guide to learning advanced JUnit testing. Each topic is explained and placed in context, and for the more inquisitive, there are more details of the concepts used. This book is for you if you are a developer with some experience in Java application development as well as a basic knowledge of JUnit testing. But for those whose skill set is void of any prior experience with JUnit testing, the book also covers basic fundamentals to get you acquainted with the concepts before putting them into practise.

  7. A novel left ventricular assist device with impeller pump and brushless motor compacted in one unit

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The impeller pump we developed has assisted the circulation of calves for two months, but further improvements to solve the problems of bearing wear and thrombosis along the bearing are desirable. Thus we have designed a new left ventricular assist device (LVAD) with impeller pump and brushless motor compacted in one unit, for which a ceramic bearing and a purge system through the bearing have been devised. The first experiments indicate that this new device could prospectively work for more than one year.

  8. Proton Testing of Advanced Stellar Compass Digital Processing Unit

    DEFF Research Database (Denmark)

    Thuesen, Gøsta; Denver, Troelz; Jørgensen, Finn E

    1999-01-01

    The Advanced Stellar Compass Digital Processing Unit was radiation tested with 300 MeV protons at Proton Irradiation Facility (PIF), Paul Scherrer Institute, Switzerland.......The Advanced Stellar Compass Digital Processing Unit was radiation tested with 300 MeV protons at Proton Irradiation Facility (PIF), Paul Scherrer Institute, Switzerland....

  9. HIV Testing in the United States

    Science.gov (United States)

    ... treated card, and mailing to lab for testing. Identification number on card is used when phoning for ... Policy Powered by WordPress.com VIP Follow Us Facebook Twitter Feeds Get the Latest on Health Policy ...

  10. Evaluation of medical devices in thoracic radiograms in intensive care unit - time to pay attention!

    Science.gov (United States)

    Moreira, Ana Sofia Linhares; Afonso, Maria da Graça Alves; Dinis, Mónica Ribeiro dos Santos Alves; dos Santos, Maria Cristina Granja Teixeira

    2016-01-01

    Objective To identify and evaluate the correct positioning of the most commonly used medical devices as visualized in thoracic radiograms of patients in the intensive care unit of our center. Methods A literature search was conducted for the criteria used to evaluate the correct positioning of medical devices on thoracic radiograms. All the thoracic radiograms performed in the intensive care unit of our center over an 18-month period were analyzed. All admissions in which at least one thoracic radiogram was performed in the intensive care unit and in which at least one medical device was identifiable in the thoracic radiogram were included. One radiogram per admission was selected for analysis. The radiograms were evaluated by an independent observer. Results Out of the 2,312 thoracic radiograms analyzed, 568 were included in this study. Several medical devices were identified, including monitoring leads, endotracheal and tracheostomy tubes, central venous catheters, pacemakers and prosthetic cardiac valves. Of the central venous catheters that were identified, 33.6% of the subclavian and 23.8% of the jugular were malpositioned. Of the endotracheal tubes, 19.9% were malpositioned, while all the tracheostomy tubes were correctly positioned. Conclusion Malpositioning of central venous catheters and endotracheal tubes is frequently identified in radiograms of patients in an intensive care unit. This is relevant because malpositioned devices may be related to adverse events. In future studies, an association between malpositioning and adverse events should be investigated. PMID:27737432

  11. Unit testing as a teaching tool in higher education

    Directory of Open Access Journals (Sweden)

    Peláez Canek

    2016-01-01

    Full Text Available Unit testing in the programming world has had a profound impact in the way modern complex systems are developed. Many Open Source and Free Software projects encourage (and in some cases, mandate the use of unit tests for new code submissions, and many software companies around the world have incorporated unit testing as part of their standard developing practices. And although not all software engineers use them, very few (if at all object their use. However, there is almost no research available pertaining the use of unit tests as a teaching tool in introductory programming courses. I have been teaching introductory programming courses in the Computer Sciences program at the Sciences Faculty in the National Autonomous University of Mexico for almost ten years, and since 2013 I have been using unit testing as a teaching tool in those courses. The intent of this paper is to discuss the results of this experience.

  12. Experimental Testing for Stability Analysis of Distributed Energy Resources Components with Storage Devices and Loads

    DEFF Research Database (Denmark)

    Mihet-Popa, Lucian; Groza, Voicu; Isleifsson, Fridrik Rafn

    2012-01-01

    Experimental Testing for Stability Analysis of Distributed Energy Resources Components with Storage Devices and Loads......Experimental Testing for Stability Analysis of Distributed Energy Resources Components with Storage Devices and Loads...

  13. United States Ski Team Fitness Testing Program.

    Science.gov (United States)

    Gettman, Larry R.

    Presented is a fitness profile designed to identify the individual athlete's strengths and weaknesses. Specifically, the areas of fitness examined are a) muscular strength; b) cardiovascular respiratory function; c) body composition; and d) motor abilities, agility, and speed. The procedures in the testing program involve the following: a) the…

  14. ENERGY EFFICIENT AND SAFE VALVE TESTING UNIT USING WIRELESS TECHNOLOGIES

    Directory of Open Access Journals (Sweden)

    V. Dhivya

    2013-04-01

    Full Text Available The valve testing unit is a high pressure test equipment to test the valve manufactured in industries. Valves are tested to ensure that they sustain high pressure in the range of 10000 to 15000 PSI for the required amount of time without any leakage. It has few drawbacks such as inefficient usage of power, fatal accidents due to the proximity of the users with the testing unit to note the valve pressure during operation. It is much dangerous for the industry personnel to note the valve pressure for every minute during operation. There are chances of bolts fitted in the valve thrown away due to the issues in the bolt fittings and the immense pressure inside the valve. Therefore in order to avoid fatal accidents andto improve the industrial safety an efficient valve testing unit is designed and developed using ZigBee wireless transmission technology. The proposed efficient pressure monitoring unit uses emerging technologies like ZigBee, RFID along with ARM 7 processor. The proposed system uses LabVIEW software to develop the monitoring unit in PC. ZigBee wireless transmission technology is used for remote monitoring of valve pressure for every minute. RFID module is used for uniquely identifying the valve and to track the test results. The proposed unit saves energy by sending a signal to turn off the air driven booster pump once the prescribed pressure level is reached. Theproposed unit also indicates the oil level of the test unit which avoids the manual intervention to verify the oil level and also detects issues in the bolts fitted in the valve by using a distance sensor which is to avoid fatal accidents by stopping the valve testing unit.

  15. Students' Beliefs about Mobile Devices vs. Desktop Computers in South Korea and the United States

    Science.gov (United States)

    Sung, Eunmo; Mayer, Richard E.

    2012-01-01

    College students in the United States and in South Korea completed a 28-item multidimensional scaling (MDS) questionnaire in which they rated the similarity of 28 pairs of multimedia learning materials on a 10-point scale (e.g., narrated animation on a mobile device Vs. movie clip on a desktop computer) and a 56-item semantic differential…

  16. Students' Beliefs about Mobile Devices vs. Desktop Computers in South Korea and the United States

    Science.gov (United States)

    Sung, Eunmo; Mayer, Richard E.

    2012-01-01

    College students in the United States and in South Korea completed a 28-item multidimensional scaling (MDS) questionnaire in which they rated the similarity of 28 pairs of multimedia learning materials on a 10-point scale (e.g., narrated animation on a mobile device Vs. movie clip on a desktop computer) and a 56-item semantic differential…

  17. Improving Size and Power in Unit Root Testing

    DEFF Research Database (Denmark)

    Haldrup, Niels; Jansson, Michael

    of recent contributions to improve upon both size and power of unit root tests and in so doing the approach of using rigorous statistical optimality criteria in the development of such tests is stressed. In addition to presenting tests where improved size can be achieved by modifying the standard Dickey......A frequent criticism of unit root tests concerns the poor power and size properties that many of such testsexhibit. However, the past decade or so intensive research has been conducted to alleviate these problems and great advances have been made. The present paper provides a selective survey......-Fuller class of tests, the paper presents theory of optimal testing and the construction of power envelopes for unit root tests underdifferent conditions allowing for serial correlation, deterministic components, assumptions regarding the initial condition, non-Gaussian errors, and the use of covariates....

  18. Screen Channel Liquid Acquisition Device Outflow Tests in Liquid Hydrogen

    Science.gov (United States)

    Hartwig, Jason W.; Chato, David J.; McQuillen, J. B.; Vera, J.; Kudlac, M. T.; Quinn, F. D.

    2013-01-01

    This paper presents experimental design and test results of the recently concluded 1-g inverted vertical outflow testing of two 325x2300 full scale liquid acquisition device (LAD) channels in liquid hydrogen (LH2). One of the channels had a perforated plate and internal cooling from a thermodynamic vent system (TVS) to enhance performance. The LADs were mounted in a tank to simulate 1-g outflow over a wide range of LH2 temperatures (20.3 - 24.2 K), pressures (100 - 350 kPa), and flow rates (0.010 - 0.055 kg/s). Results indicate that the breakdown point is dominated by liquid temperature, with a second order dependence on mass flow rate through the LAD. The best performance is always achieved in the coldest liquid states for both channels, consistent with bubble point theory. Higher flow rates cause the standard channel to break down relatively earlier than the TVS cooled channel. Both the internal TVS heat exchanger and subcooling the liquid in the propellant tank are shown to significantly improve LAD performance.

  19. Suitability and repeatability of a photostress recovery test device, the macular test device, macular degeneration TEST DEVICE, detector (MDD-2), for diabetes and diabetic retinopathy assessment

    LENUS (Irish Health Repository)

    Loughman, James

    2013-10-16

    Diabetic retinopathy can result in impaired photostress recovery time despite normal visual acuity and fundoscopic appearance. The Macular Degeneration Detector (MDD-2) is a novel flash photostress recovery time device. In this study, we examine the repeatability of the MDD-2 in normal and diabetic subjects.

  20. A New Symmetrical Unit for Breakwater Armour: First Tests

    NARCIS (Netherlands)

    Salauddin, M.; Broere, A.; Van der Meer, J.W.; Verhagen, H.J.; Bijl, E.

    2015-01-01

    A new and symmetrical single layer armour unit, the crablock, has been designed in the UAE. One breakwater was reconstructed with crablock, but very limited testing had been performed. Just to become more acquainted with this new unit, pre-competitive research at a university has been performed,

  1. Unit cell sparger test program and analysis of test results

    Energy Technology Data Exchange (ETDEWEB)

    Park, Choon Kyung; Song, C. H.; Cho, S.; Yoon, Y. J

    2003-11-01

    This report presents the results of test data from CPT-3 test and the effect of important parameters on the IRWST load. The object of CPT-3 test is to determine the influence of air mass in the piping on the IRWST (In-containment Refueling Water Storage Tank) boundary during an operation of Safety Depressurization and Vent System (SDVS). The test was conducted from an initial system pressure of 15.2 MPa, a steam temperature of 343.3 .deg. C, and an air mass of 3.34 lb. Following valve actuation, the pressure within the discharge line underwent pressure transient due to high pressure steam from the pressurizer and the discharged high pressure air formed air bubbles, which expanded and compressed periodically in the simulated IRWST. Air bubble oscillation was terminated within 2 s into the test. The magnitude of the pressure wave during the air clearing period was inversely proportional to the distance and very abrupt pressure spikes were observed in case the distance from the sparger holes to the submerged structure was less than 0.9 m. After the isolation valves were closed, the water in the simulated IRWST was considered to rise up to the 2.4m from the water surface in the quench tank. The amount of air mass in the piping, water temperature in the simulated IRWST, air temperature in the piping had not significant effect on the pressure loading during an air clearing period. However, the opening time of the isolation valve, steam mass flow rate, and submergence of an sparger have been shown to have great effects on the pressure loading during an air clearing period. 2 % of sparger flow area seems to be sufficient for the vacuum breaker area to mitigate the water hammering caused by abrupt water level rising during valve closure.

  2. Extended device profiles and testing procedures for the approval process of integrated medical devices using the IEEE 11073 communication standard.

    Science.gov (United States)

    Janß, Armin; Thorn, Johannes; Schmitz, Malte; Mildner, Alexander; Dell'Anna-Pudlik, Jasmin; Leucker, Martin; Radermacher, Klaus

    2017-08-25

    Nowadays, only closed and proprietary integrated operating room systems (IORS) from big manufacturers are available on the market. Hence, the interconnection of components from third-party vendors is only possible with increased time and costs. In the context of the German Federal Ministry of Education and Research (BMBF)-funded project OR.NET (2012-2016), the open integration of medical devices from different manufacturers was addressed. An integrated operating theater based on the open communication standard IEEE 11073 shall give clinical operators the opportunity to choose medical devices independently of the manufacturer. This approach would be advantageous especially for hospital operators and small- and medium-sized enterprises (SME) of medical devices. Actual standards and concepts regarding technical feasibility and the approval process do not cope with the requirements for a modular integration of medical devices in the operating room (OR), based on an open communication standard. Therefore, innovative approval strategies and corresponding certification and test procedures, which cover actual legal and normative standards, have to be developed in order to support the future risk management and the usability engineering process of open integrated medical devices in the OR. The use of standardized device and service profiles and a three-step testing procedure, including conformity, interoperability and integration tests are described in this paper and shall support the manufacturers to integrate their medical devices without disclosing the medical devices' risk analysis and related confidential expertise or proprietary information.

  3. Tonopah Test Range Summary of Corrective Action Units

    Energy Technology Data Exchange (ETDEWEB)

    Ronald B. Jackson

    2007-05-01

    Corrective Action Sites (CASs) and Corrective Action Units (CAUs) at the Tonopah Test Range (TTR) may be placed into three categories: Clean Closure/No Further Action, Closure in Place, or Closure in Progress.

  4. 40 CFR 63.9620 - On which units and by what date must I conduct performance tests or other initial compliance...

    Science.gov (United States)

    2010-07-01

    ... units within a group must also have the same type of air pollution control device (e.g., wet scrubbers...). You cannot group emission units with different air pollution control device types together for the... subject to initial performance testing. (2) A list of the process type and type of air pollution control...

  5. Establishing a quality management system for unit-use testing based on NCCLS proposed guideline (EP18-P).

    Science.gov (United States)

    Whitley, R J; Santrach, P J; Phillips, D L

    2001-05-01

    Point of care tests often employ unit-use test devices. By their very nature (single use, disposable, self-contained) such devices present unique challenges for quality assurance (QA) and quality control (QC). The proposed NCCLS guideline (EP18-P) recommends a quality management system for unit-use testing. The document addresses regulatory considerations, proposes the development of a partnership between users and manufacturers, provides a source of error matrix, and suggests practical approaches to quality monitoring, identification and management of these potential problems. The key to the success of this guideline is cooperation and open exchange of information among manufacturers, users, regulators, and accrediting agencies.

  6. Testing limits to airflow perturbation device (APD measurements

    Directory of Open Access Journals (Sweden)

    Jamshidi Shaya

    2008-10-01

    Full Text Available Abstract Background The Airflow Perturbation Device (APD is a lightweight, portable device that can be used to measure total respiratory resistance as well as inhalation and exhalation resistances. There is a need to determine limits to the accuracy of APD measurements for different conditions likely to occur: leaks around the mouthpiece, use of an oronasal mask, and the addition of resistance in the respiratory system. Also, there is a need for resistance measurements in patients who are ventilated. Method Ten subjects between the ages of 18 and 35 were tested for each station in the experiment. The first station involved testing the effects of leaks of known sizes on APD measurements. The second station tested the use of an oronasal mask used in conjunction with the APD during nose and mouth breathing. The third station tested the effects of two different resistances added in series with the APD mouthpiece. The fourth station tested the usage of a flexible ventilator tube in conjunction with the APD. Results All leaks reduced APD resistance measurement values. Leaks represented by two 3.2 mm diameter tubes reduced measured resistance by about 10% (4.2 cmH2O·sec/L for control and 3.9 cm H2O·sec/L for the leak. This was not statistically significant. Larger leaks given by 4.8 and 6.4 mm tubes reduced measurements significantly (3.4 and 3.0 cm cmH2O·sec/L, respectively. Mouth resistance measured with a cardboard mouthpiece gave an APD measurement of 4.2 cm H2O·sec/L and mouth resistance measured with an oronasal mask was 4.5 cm H2O·sec/L; the two were not significantly different. Nose resistance measured with the oronasal mask was 7.6 cm H2O·sec/L. Adding airflow resistances of 1.12 and 2.10 cm H2O·sec/L to the breathing circuit between the mouth and APD yielded respiratory resistance values higher than the control by 0.7 and 2.0 cm H2O·sec/L. Although breathing through a 52 cm length of flexible ventilator tubing reduced the APD

  7. Nearly Efficient Likelihood Ratio Tests of the Unit Root Hypothesis

    DEFF Research Database (Denmark)

    Jansson, Michael; Nielsen, Morten Ørregaard

    Seemingly absent from the arsenal of currently available "nearly efficient" testing procedures for the unit root hypothesis, i.e. tests whose local asymptotic power functions are indistinguishable from the Gaussian power envelope, is a test admitting a (quasi-)likelihood ratio interpretation. We...... show that the likelihood ratio unit root test derived in a Gaussian AR(1) model with standard normal innovations is nearly efficient in that model. Moreover, these desirable properties carry over to more complicated models allowing for serially correlated and/or non-Gaussian innovations....

  8. Chalcogenide Glass Radiation Sensor; Materials Development, Design and Device Testing

    Energy Technology Data Exchange (ETDEWEB)

    Mitkova, Maria; Butt, Darryl; Kozicki, Michael; Barnaby, Hugo

    2013-04-30

    studied the effect of x-rays and γ-rays, on thin film chalcogenide glasses and applied them in conjunction with film incorporating a silver source in a new type of radiation sensor for which we have an US patent application [3]. In this report, we give data about our studies regarding our designed radiation sensor along with the testing and performance at various radiation doses. These studies have been preceded by materials characterization research related to the compositional and structural characteristics of the active materials used in the radiation sensor design. During the work on the project, we collected a large volume of material since every experiment was repeated many times to verify the results. We conducted a comprehensive material research, analysis and discussion with the aim to understand the nature of the occurring effects, design different structures to harness these effects, generated models to aid in the understanding the effects, built different device structures and collected data to quantify device performance. These various aspects of our investigation have been detailed in previous quarterly reports. In this report, we present our main results and emphasize on the results pertaining to the core project goals materials development, sensor design and testing and with an emphasis on classifying the appropriate material and design for the optimal application. The report has three main parts: (i) Presentation of the main data; (ii) Bulleted summary of the most important results; (iii) List of the patent, journal publications, conference proceedings and conferences participation, occurring as a result of working on the project.

  9. Research on Test Unit for Determining Cooling Characteristics of Quenchants

    Institute of Scientific and Technical Information of China (English)

    LI Lin-lin; ZHANG Wei-min; CHEN Nai-lu; LIU Zhan-cang; LIU Yang

    2004-01-01

    According to ASTM Designation DXXXX Standard Test Method for Determination of Cooling Characteristics of Quenchants by Cooling Curve Analysis with Agitation (Drayton Unit), a test unit was designed using which the cooling characteristics of a quenchant at different flow rates and different temperatures can be determined. We discussed the effects of flow rate and temperature on cooling characteristics of fast speed quenching oil. The results show that this unit can be well used for determining cooling characteristics of quechants at different flow rates and different temperatures. At the same time our investigation can provide a reference to the establishment of a standard for determination of cooling characteristics of quenchants with agitation.

  10. Underwater Sound Levels at a Wave Energy Device Testing Facility in Falmouth Bay, UK.

    Science.gov (United States)

    Garrett, Joanne K; Witt, Matthew J; Johanning, Lars

    2016-01-01

    Passive acoustic monitoring devices were deployed at FaBTest in Falmouth Bay, UK, a marine renewable energy device testing facility during trials of a wave energy device. The area supports considerable commercial shipping and recreational boating along with diverse marine fauna. Noise monitoring occurred during (1) a baseline period, (2) installation activity, (3) the device in situ with inactive power status, and (4) the device in situ with active power status. This paper discusses the preliminary findings of the sound recording at FabTest during these different activity periods of a wave energy device trial.

  11. Nearly Efficient Likelihood Ratio Tests for Seasonal Unit Roots

    DEFF Research Database (Denmark)

    Jansson, Michael; Nielsen, Morten Ørregaard

    that these tests are "nearly efficient" in the sense of Elliott, Rothenberg, and Stock (1996), i.e. that their local asymptotic power functions are indistinguishable from the Gaussian power envelope. Currently available nearly efficient testing procedures for seasonal unit roots are regression-based and require...

  12. A review of United Nations tests for explosivity

    NARCIS (Netherlands)

    Brown, A.K.; Mak, W.A.; Whitmore, M.W.

    2000-01-01

    In attempting to develop a closed pressure vessel test for assessing explosivity, arising from propagation of detonation, deflagration or thermal explosion, some difficulties were encountered in relation to United Nations test methods. This led to a review of these methods and comparisons of their p

  13. The Road Side Unit for the A270 Test Site

    NARCIS (Netherlands)

    Passchier, I.; Driessen, B.J.F.; Heijligers, B.M.R.; Netten, B.D.; Schackmann, P.P.M.

    2011-01-01

    The design and implementation of the Road Side Unit for the A270 Test Site is presented. It consists of a sensor platform and V2I communication platform with full coverage of the test site. A service platform enables applications to make use of these facilities. The RSU will be used both for the imp

  14. [Research of joint-robotics-based design of biomechanics testing device on human spine].

    Science.gov (United States)

    Deng, Guoyong; Tian, Lianfang; Mao, Zongyuan

    2009-12-01

    This paper introduces the hardware and software of a biomechanical robot-based testing device. The bottom control orders, posture and torque data transmission, and the control algorithms are integrated in a unified visual control platform by Visual C+ +, with easy control and management. By using hybrid force-displacement control method to load the human spine, we can test the organizational structure and the force state of the FSU (Functional spinal unit) well, which overcomes the shortcomings due to the separation of the force and displacement measurement, thus greatly improves the measurement accuracy. Also it is esay to identify the spinal degeneration and the load-bearing impact on the organizational structure of the FSU after various types of surgery.

  15. The Power of Unit Root Tests Against Nonlinear Local Alternatives

    DEFF Research Database (Denmark)

    Demetrescu, Matei; Kruse, Robinson

    of Econometrics 112, 359-379) in comparison to the linear Dickey-Fuller test. To this end, we consider different adjustment schemes for deterministic terms. We provide asymptotic results which imply that the error variance has a severe impact on the behavior of the tests in the nonlinear case; the reason...... by simulation. Furthermore, our own simulation results suggest that the user-specied adjustment scheme for deterministic components (e.g. OLS, GLS, or recursive adjustment) has a much higher impact on the power of unit root tests than accounting for nonlinearity, at least under local (linear or nonlinear......This article extends the analysis of local power of unit root tests in a nonlinear direction by considering local nonlinear alternatives and tests built specically against stationary nonlinear models. In particular, we focus on the popular test proposed by Kapetanios et al. (2003, Journal...

  16. The current situation and development of medical device testing institutes in China.

    Science.gov (United States)

    Yang, Xiaofang; Mu, Ruihong; Fan, Yubo; Wang, Chunren; Li, Deyu

    2017-04-01

    This article analyses the current situation and development of Chinese medical device testing institutes from the perspectives of the two most important functions - testing functions and medical device standardization functions. Areas Covered: The objective of the Chinese government regulations for medical device industry is to ensure the safety and effectiveness of medical devices for Chinese patients. To support the regulation system, the Chinese government has established medical device testing institutes at different levels for example, the national, provincial, and municipal levels. These testing institutes also play an important role in technical support during medical device premarket registration and post market surveillance, they are also the vital practitioners of Chinese medical device standardization. Expert Commentary: Chinese medical device testing institutes are technical departments established by government, and serve the regulatory functions of government agency. In recent years, with the rapid development of medical device industry as well as constantly increasing international and domestic medical device market, the importance of medical device testing institute is more prominent, However, there are still some problems unsolved, such as their overall capacity remains to be improved, construction of standardization is to be strengthened, etc.

  17. STATIC TESTS OF UNCONVENTIONAL PROPULSION UNITS FOR ULTRALIGHT AIRPLANES

    Directory of Open Access Journals (Sweden)

    Martin Helmich

    2014-06-01

    Full Text Available This paper presents static tests of a new unconventional propulsion unit for small aviation airplanes. Our laboratory stand – a fan drive demonstrator – enables us to compare various design options. We performed experiments to verify the propulsion functionality and a measurement procedure to determine the available thrust of the propulsion unit and its dependence on engine speed. The results used for subsequent optimization include the operating parameters of the propulsion unit, and the temperature and velocity fields in parts of the air duct.

  18. MEMS device for bending test: measurements of fatigue and creep of electroplated nickel

    DEFF Research Database (Denmark)

    Larsen, Kristian Pontoppidan; Rasmussen, Anette Alsted; Ravnkilde, Jan Tue;

    2003-01-01

    In situ bending test devices with integrated electrostatic actuator were fabricated in electroplated nanocrystalline nickel. The device features approximately pure in-plane bending of the test beam. The excitation of the test beam has fixed displacement amplitude as the actuation electrodes are o...

  19. Tests and studies on improved innovativeness of sand reclamation units

    Directory of Open Access Journals (Sweden)

    F. Pezarski

    2007-04-01

    Full Text Available The aim of the present study was raising the innovativeness of sand reclamation units through application of a new material - austempered ductile iron (ADI - for elements exposed to abrasion wear and impacts. Methods used for casting of ADI blades for disk-type reclamation units were described along with the results of tests and measurements of the obtained hardness, strength and microstructure. The ready ADI castings of blades were next subjected to performance tests to compare them with the conventionally made cast steel blades operating under industrial conditions. The obtained results of the tests confirmed high properties and numerous benefits offered by ADI respetive of cast steel used as a material for elements of sand reclamation units.

  20. Feasibility test on green energy harvesting from physical exercise devices

    Science.gov (United States)

    Mustafi, Nirendra N.; Mourshed, M.; Masud, M. H.; Hossain, M. S.; Kamal, M. R.

    2017-06-01

    The demand of power is increasing day by day due to the increase of world population as well as the industrialization and modernization. Depletion of the world's fossil fuel reserves and the adverse effects of their uses on the environment insist the researchers to find out some means of efficient and cost effective alternative energy sources from small to large scales. In a gymnasium the human metabolism power is used to drive the physical exercise devices. However there are a number of exercise device which can have the potential to generate electricity during physical exercise. By converting the available mechanical energy from these exercise devices into kinetic energy, electric power can be produced. In this work, energy was harvested from the most commonly used physical exercise devices used in the gymnasium - paddling and chin up. The paddle pulley and the chin up pulley were connected to the couple pulley which in turn coupled to an alternator by a V-belt to produce electrical energy and a rechargeable battery was used to store electrical energy. The power generation from the device depends upon the speed at which the alternator runs and the age limit. The electrical energy output was observed 83.6 watt at 1300 rpm and 62.5 watt at1150 rpm alternator speed for the paddling and chin up respectively recorded for an average adult. The device was designed for a constant 49N load on the alternator for both paddling and chin up operation. By running each of these devices for about 12 hours in a day, any gymnasium can avoid burning of almost 23.67 kg and 31.6 kg of diesel fuel per year for chin up and paddling respectively. Also it can cut off the CO2 emission to the environment which reveals itself a standalone green micro gym.

  1. LANL12-RS-108J Report on Device Modeler Testing of the Device Modeler Tool Kit. DMTK in FY14

    Energy Technology Data Exchange (ETDEWEB)

    Temple, Brian Allen [Los Alamos National Laboratory (LANL), Los Alamos, NM (United States); Pimentel, David A. [Los Alamos National Laboratory (LANL), Los Alamos, NM (United States)

    2014-09-28

    This document covers the various testing and modifications of the Device Modeler Tool Kit (DMTK) for project LANL12-RS-108J in FY14. The testing has been comprised of different device modelers and trainees for device modeling using DMTK on the secure network for a few test problems. Most of these problems have been synthetic data problems. There has been a local secure network training drill where one of the trainees has used DMTK for real data. DMTK has also been used on a laptop for a deployed real data training drill. Once DMTK gets into the home team, it will be used for more training drills (TDs) which will contain real data in the future.

  2. Blast Mitigation Sea Analysis - Evaluation of Lumbar Compression Data Trends in 5th Percentile Female Anthropomorphic Test Device Performance Compared to 50th Percentile Male Anthropomorphic Test Device in Drop Tower Testing

    Science.gov (United States)

    2016-08-21

    in 5th Percentile Female Anthropomorphic Test Device Performance Compared to 50th Percentile Male Anthropomorphic Test Device in Drop Tower Testing ...for advertising or product endorsement purposes. UNCLASSIFIED UNCLASSIFIED • Baseline drop tower data collected from Anthropomorphic Test Devices (ATDs...development • Testing completed with: – 5th Percentile Female ATDs and 50th Percentile Male Hybrid III ATDs – 200 g or 350 g pulse • ATD data quality

  3. Stress mitigation of x-ray beamline monochromators using topography test unit.

    Energy Technology Data Exchange (ETDEWEB)

    Maj, J.; Waldschmidt, G.; Baldo, P.; Macrander, A.; Koshelev, I.; Huang, R.; Maj, L.; Maj, A.; Univ. of Chicago; Northeastern Ohio Univ. Coll. of Medicine; Rosalind Franklin Univ. of Medicine and Science

    2007-01-01

    Silicon and diamond monochromators (crystals), often used in the Advanced Photon Source X-ray beamlines, require a good quality surface finish and stress-free installation to ensure optimal performance. The device used to mount the crystal has been shown to be ajor contributing source of stress. In this case, an adjustable mounting device is an effective method of reducing stresses and improve the rocking curve to levels much closer to ideal. Analysis by a topography test unit has been used to determine the distribution of stresses and to measure the rocking curve, as well as create CCD images of the crystal. This paper describes the process of measuring these stresses and manipulating the mounting device and crystal to create a substantially improved monochromator.

  4. Systematic Unit Testing in a Read-eval-print Loop

    DEFF Research Database (Denmark)

    Nørmark, Kurt

    2010-01-01

    Lisp programmers constantly carry out experiments in a read-eval-print loop.  The experimental activities convince the Lisp programmers that new or modified pieces of programs work as expected.  But the experiments typically do not represent systematic and comprehensive unit testing efforts...... how to use a test repository for other purposes than testing.  As a concrete contribution we show how to use test cases as examples in library interface documentation.  It is hypothesized---but not yet validated---that the tool will motivate the Lisp programmer to take the transition from casual...

  5. Simple non-destructive tests for electroexplosive devices

    Science.gov (United States)

    Rosenthal, L. A.; Menichelli, V. J.

    1972-01-01

    Electrothermal behavior of bridgewire-explosive interface is defined by pulsing electroexplosive device with a safe level of current and examining the resistance variation of bridgewire. Bridgewire provides signal which describes average wire temperature and heat sinking to the explosive and enclosure.

  6. Test Plan for Godiva Move from LANL TA-18 to Nevada Test Site Device Assembly Facility

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, M

    2005-08-01

    Godiva is an unshielded, pulsed nuclear reactor, used to produce bursts of neutrons and gamma rays for irradiating test samples. The Godiva reactor is part of the TA-18 Facility at Los Alamos National Laboratory. The Godiva reactor is to be moved to the Device Assembly Facility (DAF) at the Nevada Test Site, northwest of Las Vegas, Nevada. Bursts of ionizing radiation from Godiva have been found to produce radio waves and electrical interference in circuits and electrical equipment (e.g., alarm systems, interlocks, recording devices) near Godiva. Safety and security concerns regarding Godiva at the DAF are: (1) Can Godiva pulses induce detonators elsewhere in the DAF to explode?, (2) What is the expected strength of the electrical signal from Godiva elsewhere in the DAF? (3) Will Godiva pulses trigger security alarms, requiring additional administrative controls? This report addresses these issues, and describes a brief set of electrical measurements intended to verify that electromagnetic emissions from Godiva are unchanged by its relocation, and below a threshold of safety for detonators that are outside the actual room Godiva resides in. The following points will be described: the nature of Godiva electrical emissions, predicted electric field at a given distance, electromagnetic frequency, safety threshold for detonators, recommended ''stay out'' zone around Godiva for detonators, and recommended measurements to be made once Godiva has been installed at DAF.

  7. China First Full-scale Comprehensive Drilling Test Unit

    Institute of Scientific and Technical Information of China (English)

    Zhang Ailin

    1997-01-01

    @@ The full-scale comprehensive drilling test unit built in Daqing Oilfields is the first one in China which can simulate the bottom-hole environments and the working conditions of drilling string with well depth up to 6 000 m.

  8. Traceable working standards with SI units of radiance for characterizing the measurement performance of investigational clinical NIRF imaging devices

    Science.gov (United States)

    Zhu, Banghe; Rasmussen, John C.; Litorja, Maritoni; Sevick-Muraca, Eva M.

    2017-03-01

    All medical devices for Food and Drug market approval require specifications of performance based upon International System of Units (SI) or units derived from SI for reasons of traceability. Recently, near-infrared fluorescence (NIRF) imaging devices of a variety of designs have emerged on the market and in investigational clinical studies. Yet the design of devices used in the clinical studies vary widely, suggesting variable device performance. Device performance depends upon optimal excitation of NIRF imaging agents, rejection of backscattered excitation and ambient light, and selective collection of fluorescence emanating from the fluorophore. There remains no traceable working standards with SI units of radiance to enable prediction that a given molecular imaging agent can be detected in humans by a given NIRF imaging device. Furthermore, as technologies evolve and as NIRF imaging device components change, there remains no standardized means to track device improvements over time and establish clinical performance without involving clinical trials, often costly. In this study, we deployed a methodology to calibrate luminescent radiance of a stable, solid phantom in SI units of mW/cm2/sr for characterizing the measurement performance of ICCD and IsCMOS camera based NIRF imaging devices, such as signal-to-noise ratio (SNR) and contrast. The methodology allowed determination of superior SNR of the ICCD over the IsCMOS system; comparable contrast of ICCD and IsCMOS depending upon binning strategies.

  9. Mobile device use while driving--United States and seven European countries, 2011.

    Science.gov (United States)

    2013-03-15

    Road traffic crashes are a global public health problem, contributing to an estimated 1.3 million deaths annually. Known risk factors for road traffic crashes and related injuries and deaths include speed, alcohol, nonuse of restraints, and nonuse of helmets. More recently, driver distraction has become an emerging concern. To assess the prevalence of mobile device use while driving in Belgium, France, Germany, the Netherlands, Portugal, Spain, the United Kingdom (UK), and the United States, CDC analyzed data from the 2011 EuroPNStyles and HealthStyles surveys. Prevalence estimates for self-reported talking on a cell phone while driving and reading or sending text or e-mail messages while driving were calculated. This report describes the results of that analysis, which indicated that, among drivers ages 18-64 years, the prevalence of talking on a cell phone while driving at least once in the past 30 days ranged from 21% in the UK to 69% in the United States, and the prevalence of drivers who had read or sent text or e-mail messages while driving at least once in the past 30 days ranged from 15% in Spain to 31% in Portugal and the United States. Lessons learned from successful road safety efforts aimed at reducing other risky driving behaviors, such as seat belt nonuse and alcohol-impaired driving, could be helpful to the United States and other countries in addressing this issue. Strategies such as legislation combined with high-visibility enforcement and public education campaigns deserve further research to determine their effectiveness in reducing mobile device use while driving. Additionally, the role of emerging vehicle and mobile communication technologies in reducing distracted driving-related crashes should be explored.

  10. Progress on Broadband Access to the Internet and Use of Mobile Devices in the United States.

    Science.gov (United States)

    Serrano, Katrina J; Thai, Chan L; Greenberg, Alexandra J; Blake, Kelly D; Moser, Richard P; Hesse, Bradford W

    Healthy People 2020 (HP2020) aims to improve population health outcomes through several objectives, including health communication and health information technology. We used 7 administrations of the Health Information National Trends Survey to examine HP2020 goals toward access to the Internet through broadband and mobile devices (N = 34 080). We conducted descriptive analyses and obtained predicted marginals, also known as model-adjusted risks, to estimate the association between demographic characteristics and use of mobile devices. The HP2020 target (7.7% of the US population) for accessing the Internet through a cellular network was surpassed in 2014 (59.7%), but the HP2020 target (83.2%) for broadband access fell short (63.8%). Sex and age were associated with accessing the Internet through a cellular network throughout the years (Wald F test, P mobile devices presents an opportunity for technology-based health interventions that should be explored.

  11. Establishment of Testing Device for Shielding Performance of X and Gamma Ray Radiation Protection Materials

    Institute of Scientific and Technical Information of China (English)

    SONG; Ming-zhe; WEI; Ke-xin; HOU; Jin-bing; WANG; Hong-yu; GAO; Fei; NI; Ning

    2015-01-01

    X and gamma ray radiation protective material shielding performance testing device was built based on the international standard IEC61331.1-2014.The device can be used to test attenuation ratio,attenuation equivalent and lead equivalent of radiation protective material in"narrow beam condition","broad beam condition"and"inverse

  12. Testing an innovative device against airborne Aspergillus contamination.

    Science.gov (United States)

    Desoubeaux, Guillaume; Bernard, Marie-Charlotte; Gros, Valérie; Sarradin, Pierre; Perrodeau, Elodie; Vecellio, Laurent; Piscopo, Antoine; Chandenier, Jacques; Bernard, Louis

    2014-08-01

    Aspergillus fumigatus is a major airborne nosocomial pathogen that is responsible for severe mycosis in immunocompromised patients. We studied the efficacy of an innovative mobile air-treatment device in eliminating A. fumigatus from the air following experimental massive contamination in a high-security room. Viable mycological particles were isolated from sequential air samples in order to evaluate the device's effectiveness in removing the fungus. The concentration of airborne conidia was reduced by 95% in 18 min. Contamination was reduced below the detection threshold in 29 min, even when the machine was at the lowest airflow setting. In contrast, during spontaneous settling with no air treatment, conidia remained airborne for more than 1 h. This indoor air contamination model provided consistent and reproducible results. Because the air purifier proved to be effective at eliminating a major contaminant, it may prove useful in preventing air-transmitted disease agents. In an experimental space mimicking a hospital room, the AirLyse air purifier, which uses a combination of germicidal ultraviolet C irradiation and titanium photocatalysis, effectively eliminated Aspergillus conidia. Such a mobile device may be useful in routine practice for lowering microbiological air contamination in the rooms of patients at risk.

  13. Light-weight radioisotope heater unit (LWRHU) impact tests

    Science.gov (United States)

    Reimus, M. A. H.; Rinehart, G. H.; Herrera, A.; Lopez, B.; Lynch, C.; Moniz, P.

    1998-01-01

    The light-weight radioisotope heater unit (LWRHU) is a 238PuO2-fueled heat source designed to provide one thermal watt in each of various locations on a spacecraft. Los Alamos National Laboratory designed, fabricated, and safety tested the LWRHU. The heat source consists of a hot-pressed 238PuO2 fuel pellet, a Pt-30Rh vented capsule, a pyrolytic graphite insulator, and a fineweave-pierced fabric graphite aeroshell assembly. To compare the performance of the LWRHUs fabricated for the Cassini mission with the performance of those fabricated for the Galileo mission, and to determine a failure threshold, two types of impact tests were conducted. A post-reentry impact test was performed on one of 180 flight-quality units produced for the Cassini mission and a series of sequential impact tests using simulant-fueled LWRHU capsules were conducted respectively. The results showed that deformation and fuel containment of the impacted Cassini LWRHU was similar to that of a previously tested Galileo LWRHU. Both units sustained minimal deformation of the aeroshell and fueled capsule; the fuel was entirely contained by the platinum capsule. Sequential impacting, in both end-on and side-on orientations, resulted in increased damage with each subsequent impact. Sequential impacting of the LWRHU appears to result in slightly greater damage than a single impact at the final impact velocity of 50 m/s.

  14. Coating, Degrading and Testing of Organic Polymer Devices - Reducing the route from Laboratory to Production scale devices

    DEFF Research Database (Denmark)

    Dam, Henrik Friis

    to test solar cell devices without the need of expensive multipurpose source meters. This also shows the potential for stand-alone test, especially relevant for the various outdoor test conducted around the world and for the logging of various high-impact parameters, such as temperature, humidity...... thousand cells manufactured in the process for creating a recipe that would allow a wet processed layer on layer coating to function without having penetration and dissolution through the up to 12 separately printed layers. Testing and analysis of a nanoparticle based method with water used...

  15. Transient Testing of Nuclear Fuels and Materials in the United States

    Science.gov (United States)

    Wachs, Daniel M.

    2012-12-01

    The United States has established that transient irradiation testing is needed to support advanced light water reactors fuel development. The U.S. Department of Energy (DOE) has initiated an effort to reestablish this capability. Restart of the Transient Testing Reactor (TREAT) facility located at the Idaho National Laboratory (INL) is being considered for this purpose. This effort would also include the development of specialized test vehicles to support stagnant capsule and flowing loop tests as well as the enhancement of postirradiation examination capabilities and remote device assembly capabilities at the Hot Fuel Examination Facility. It is anticipated that the capability will be available to support testing by 2018, as required to meet the DOE goals for the development of accident-tolerant LWR fuel designs.

  16. Comparison of Controlled Field Test Aerosol Generation Devices to a Laboratory Device

    Science.gov (United States)

    2013-11-01

    aerodynamic diameter APS aerodynamic particle sizer BG Bacillus globigii CCU confidence checker unit ECBC U.S. Army Edgewood Chemical Biological Center...of airborne biological threats. Detectors monitor the size, concentration, and fluorescence of airborne particles and provide an alarm if an internal...4 3. The IJAG system produced particles for measurement by the aerodynamic particle sizer (APS

  17. Reference Excitation Unit for Micro-Vibration Test Facilities

    Science.gov (United States)

    Veal, Dan; Hughes, Ben; Wagner, Mark

    2012-07-01

    The verification of hardware, in particular with respect to micro-vibration requirements, is challenging for both numerical simulation and experimental methodology. A commonly used test approach is to measure the interface reaction forces, torques, accelerations, velocities or displacements in all six degrees of freedom generated by the unit under test. In Europe, several test facilities exist to measure these generated micro-vibration forces based on dynamometer, pendulum and reverse pendulum principles. All these facilities and test setups need to be validated and calibrated with traceability to recognized international standards to ensure validity of the measurement results. Ideally, inter-facility comparisons would be conducted with identical excitation input signals and identical boundary conditions to increase confidence in the validity of the measurement produced by different facilities. To facilitate this requirement, the National Physical Laboratory (NPL) - the UK’s national measurement institute, is developing a reference vibration excitation unit that will be capable of generating vibrations, linear or angular, of known amplitude and direction traceable to international standards. This activity is funded by the European Space Agency (ESA) in the frame of a Technology Research Study. This paper covers the design of the unit and how the vibrations generated will be traceable to international standards.

  18. Pre-operational environmental monitoring plan for the Device Assembly Facility at the Nevada Test Site

    Energy Technology Data Exchange (ETDEWEB)

    Ferate, F.D.

    1995-01-01

    Nuclear explosives operations have been and may continue to be an important component of the DOE mission at the NTS. This mission has been to conduct the nation`s nuclear testing program in a safe, secure, and efficient manner while assuring full compliance with state and federal regulations, and DOE order`s and directives. These operations have generally included assembly, disassembly or modification, staging, transportation, and tesbng of nuclear explosive devices. They may also include maintenance, repair, retrofit, and surveillance. The Device Assembly Facility (DAF) was constructed to provide a dedicated facility in which to prepare nuclear explosives assemblies for their intended disposition. This facility will provide for combined operations (replacing two separate facilities) and incorporates state-of-the-art safety and security features while minimizing the risks of environmental impacts. The facility has been completed but not yet operated, so the impacts to be considered will b e based on normal operations and not on the impacts of construction activities. The impacts will arise from nuclear explosives operations that require the handling of high explosives in combination with special nuclear materials. Wastes from operation of the earlier device assembly facilities have included grams of epoxies, pints of solvents, and small quantities of waste explosives. These are hazardous (includes radioactive) wastes and are disposed of in accordance with state and federal regulations. Assuming similar operations at the DAF, non-hazardous (includes non-radioactive) solid waste would be transported to a permitted landfill. Waste explosives would be sent to the Area 11 Explosive Ordnance Disposal Unit. Other hazardous waste would be sent to the Area 5 Radioactive Waste.Management Site for shipment or burial.

  19. Dynamic test devices for analyzing the tensile properties of concrete

    NARCIS (Netherlands)

    Forquin, P.; Riedel, W.; Weerheijm, J.

    2013-01-01

    Owing to their low tensile failure strain, concrete is a difficult material to test under dynamic tensile loading. Indeed, conventional testing apparatuses such as high-speed hydraulic presses or Split Hopkinson Bar facilities rely on a mechanical balance of the specimen implying a short round-trip

  20. Evaluation of 3 dental unit waterline contamination testing methods

    OpenAIRE

    Porteous, Nuala; Sun, Yuyu; Schoolfield, John

    2015-01-01

    Previous studies have found inconsistent results from testing methods used to measure heterotrophic plate count (HPC) bacteria in dental unit waterline (DUWL) samples. This study used 63 samples to compare the results obtained from an in-office chairside method and 2 currently used commercial laboratory HPC methods (Standard Methods 9215C and 9215E). The results suggest that the Standard Method 9215E is not suitable for application to DUWL quality monitoring, due to the detection of limited n...

  1. Design and Testing of Electronic Devices for Harsh Environments

    CERN Document Server

    Nico, Costantino

    This thesis reports an overview and the main results of the research activity carried out within the PhD programme in Information Engineering of the University of Pisa (2010-2012). The research activity has been focused on different fields, including Automotive and High Energy Physics experiments, according to a common denominator: the development of electroni c devices and systems operating in harsh environments. There are many applications that forc e the adoption of design methodologies and strategies focused on this type of envir onments: military, biom edical, automotive, industrial and space. The development of solutions fulfilling specific operational requirements, therefore represents an interesting field of research. The first research activity has been framed within the ATHENIS project, funded by the CORDIS Commission of the European Community, and aiming at the development of a System-on-Chip, a r egulator for alternators employed on vehicles, presenting both configurability an d t...

  2. Evaluation of in-office dental unit waterline testing.

    Science.gov (United States)

    Momeni, Stephanie S; Tomline, Nancy; Ruby, John D; Dasanayake, Ananda P

    2012-01-01

    In-office dental unit waterline (DUWL) testing systems are commercially available for monitoring DUWL bacteria. The current study compared Aquasafe, Petrifilm, and Heterotrophic Plate Count Sampler (HPCS) with R2A plating methodology, considered the gold standard for enumerating heterotrophic bacteria in potable water. Samples were collected from 20 dental units. Heterotrophic bacterial counts of ≤500 CFUs/mL were used as the cut-off for assessing in-office testing compared to R2A laboratory plating. Validity was assessed using sensitivity and specificity, along with positive and negative predictive values. Results were also compared using concordance and kappa statistics. All in-office tests demonstrated 100% specificity and positive predictive values, while sensitivity and negative predictive values were low (Petrifilm, 57%/50%; HPCS, 50%/46%; Aquasafe, 21%/35%). Concordance and kappa values for agreement with R2A plating were as follows: Petrifilm 70% (κ = 0.44), HPCS 65% (κ = 0.38), and Aquasafe 45% (κ = 0.14). In-office DUWL testing with Aquasafe, Petrifilm, and HPCS agreed poorly with R2A plating methodology and is not valid or reliable as a means of accurately monitoring bacterial density in DUWL. These in-office test systems should not be used for assessing compliance with the ADA and CDC standard for acceptable heterotrophic bacterial counts in DUWLs (≤500 CFUs/mL).

  3. Results of long-term field tests of protective earthing device for vessel electric systems

    Directory of Open Access Journals (Sweden)

    Blaginin V.A.

    2015-03-01

    Full Text Available The results of prolonged natural tests of protective neutral earthing device for controlling the fire and electrical safety of vessel electric systems have been shown. The use of such devices provides safe single-phase fault currents and reducing arc overvoltage during the long-term operation of a ship. The results of long-term monitoring of the device operation as part of the existing vessel electric power system have confirmed its effectiveness

  4. Results of long-term field tests of protective earthing device for vessel electric systems

    OpenAIRE

    Blaginin V.A.; Kazhekin I.E.; Yusyp V.M.; Moskalyuk A.M.; Syrenko D.P.

    2015-01-01

    The results of prolonged natural tests of protective neutral earthing device for controlling the fire and electrical safety of vessel electric systems have been shown. The use of such devices provides safe single-phase fault currents and reducing arc overvoltage during the long-term operation of a ship. The results of long-term monitoring of the device operation as part of the existing vessel electric power system have confirmed its effectiveness

  5. TESTING NEW TYPES OF ROLLING STOCK FOR ELECTROMAGNETIC COMPATIBILITY WITH SIGNALING AND COMMUNICATION DEVICES

    Directory of Open Access Journals (Sweden)

    V. I. Havrilyuk

    2015-09-01

    Full Text Available Purpose. In the paper there is the comparative analysis of standards and methods of measurements of electromagnetic interference, those are caused by electrical equipment of new types of rolling stock with AC and DC-current electric traction in accordance with the normative documents are adopted in Ukraine and the EU. The development on this basis the measuring method of current interference in traction network, generated by the electrical equipment of electric rolling stock (ERS applicable to testing the new types of rolling stock for electromagnetic compatibility (EMC with different systems of railway signaling is also needed. Methodology. The testing method has been offered. It includes measurements in power circuits of rolling stock, as well as in track devices of signalization systems. Findings. Norms and methods tests of a rolling stock on electromagnetic compatibility with track circuits (TC were analyzed. It was found that a large variety of electricity supply systems, signalization and link in Europe makes it necessary to test new types of electric rolling stock for electromagnetic compatibility with pick up unit in each country separately, taking into account the features used in its systems. It is greatly increases the cost of introducing new types of rolling stock. The test method of electric rolling stock EMC with track circuits has been developed; it includes measurement in power circuits of rolling stock, as well as in track devices of signalization systems. Measurements in accordance with the proposed methodology for electric rolling stock with asynchronous traction drive when driving on sections electrified at AC and DC have been carried out. The values of the interference current in track circuit to all the frequencies of the signal current have been defined. It is shown that under some modes of the train the interference current exceed the permissible values. Originality. The method for measuring interference current generated

  6. Systematic Unit Testing in a Read-eval-print Loop

    DEFF Research Database (Denmark)

    Nørmark, Kurt

    2010-01-01

    .  Rather, the experiments are quick and dirty one shot validations which do not add lasting value to the software, which is being developed.  In this paper we propose a tool that is able to collect, organize, and re-validate test cases, which are entered as expressions in a read-eval-print loop......Lisp programmers constantly carry out experiments in a read-eval-print loop.  The experimental activities convince the Lisp programmers that new or modified pieces of programs work as expected.  But the experiments typically do not represent systematic and comprehensive unit testing efforts.......  The process of collecting the expressions and their results imposes only little extra work on the programmer.  The use of the tool provides for creation of test repositories, and it is intended to catalyze a much more systematic approach to unit testing in a read-eval-print loop.  In the paper we also discuss...

  7. WTP Waste Feed Qualification: Glass Fabrication Unit Operation Testing Report

    Energy Technology Data Exchange (ETDEWEB)

    Stone, M. E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Hanford Missions Programs; Newell, J. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Process Technology Programs; Johnson, F. C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Engineering Process Development; Edwards, T. B. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Engineering Process Development

    2016-07-14

    The waste feed qualification program is being developed to protect the Hanford Tank Waste Treatment and Immobilization Plant (WTP) design, safety basis, and technical basis by assuring waste acceptance requirements are met for each staged waste feed campaign prior to transfer from the Tank Operations Contractor to the feed receipt vessels inside the Pretreatment Facility. The Waste Feed Qualification Program Plan describes the three components of waste feed qualification: 1. Demonstrate compliance with the waste acceptance criteria 2. Determine waste processability 3. Test unit operations at laboratory scale. The glass fabrication unit operation is the final step in the process demonstration portion of the waste feed qualification process. This unit operation generally consists of combining each of the waste feed streams (high-level waste (HLW) and low-activity waste (LAW)) with Glass Forming Chemicals (GFCs), fabricating glass coupons, performing chemical composition analysis before and after glass fabrication, measuring hydrogen generation rate either before or after glass former addition, measuring rheological properties before and after glass former addition, and visual observation of the resulting glass coupons. Critical aspects of this unit operation are mixing and sampling of the waste and melter feeds to ensure representative samples are obtained as well as ensuring the fabrication process for the glass coupon is adequate. Testing was performed using a range of simulants (LAW and HLW simulants), and these simulants were mixed with high and low bounding amounts of GFCs to evaluate the mixing, sampling, and glass preparation steps in shielded cells using laboratory techniques. The tests were performed with off-the-shelf equipment at the Savannah River National Laboratory (SRNL) that is similar to equipment used in the SRNL work during qualification of waste feed for the Defense Waste Processing Facility (DWPF) and other waste treatment facilities at the

  8. A qualification test for relay contacts as isolation devices in nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Beck, C.E.; Behera, A.K. [Kiran Consultants, Inc., Downers Grove, IL (United States); Polanco, S.; Terry, B. [ComEd Materials Engineering Group, Bolingbrook, IL (United States). Central Receiving, Inspection, and Test Facility

    1995-10-01

    A methodology is introduced for testing the integrity of relay contacts as isolation devices in Class IE circuits. A design activity that installed a new relay established the need for a new type of qualification test. This paper descries the process of establishing the test methodology, the development of the test plan, and the results of testing. It also describes the limitations of applying the results of any specific test to actual field installations, and offers other potential uses of the methodology.

  9. The Growing Public Health Challenges of Exposure to Ultraviolet Radiation From Use of Indoor Tanning Devices in the United States.

    Science.gov (United States)

    Bowman, Diana M; Lewis, Ryan C; Lee, Maximilian S; Yao, Catherine J

    2015-08-01

    Ultraviolet radiation is recognized as a human carcinogen by the International Agency for Research on Cancer, the world's authority on cancer research. In particular, exposure to ultraviolet radiation can lead to melanoma of the skin, which is the deadliest form of skin cancer in the United States. Yet despite the significant public health burden that is associated with skin cancer in the United States, each year over a million Americans engage in indoor tanning where exposure to artificial ultraviolet radiation occurs. In this article, we argue for an immediate ban on the use of commercial indoor tanning by minors and, based on international precedents, the phasing out of all commercial tanning operations in the United States. We consider the use of indoor tanning devices in the United States, epidemiological data on indoor tanning devices and cancer, regulation of tanning devices, and scientific evidence for increased government intervention.

  10. Test of swedish anti-skid devices on five different slippery surfaces.

    Science.gov (United States)

    Gard, G; Lundborg, G

    2001-01-01

    The interest for effective preventive strategies for slips and falls is growing. Much remains to be done, however, to prevent slips and falls in the traffic environment. Some pedestrians are injured because of slippery pavements and roadways. Using an appropriate anti-skid device may reduce the risk of slips and falls on different surfaces outdoors during winter. The aim of this study was to evaluate new anti-skid devices on the Swedish market representing three different designs of anti-skid devices; heel device, fore-foot device and whole-foot device on different slippery surfaces, gravel, sand, salt, snow and ice. The evaluations were done according to subject's perceived walking safety and balance, videorecordings of walking postures and movements, time to take on and off each anti-skid device, advantages/disadvantages with each anti-skid device and a list of priority for own use according to three criteria; safety, balance and appearance. Practical tests were carried out on different slippery surfaces, gravel, sand, salt, snow and ice. The subject's were randomly selected from the registered population over 55 years in a city in northern Sweden. The results showed that eight or more of the ten subjects perceived all four anti-skid devices as fairly good or good regarding walking safety and balance when walking on gravel, sand, and salt. Anti-skid device 3, a whole-foot device was perceived as having none or bad walking safety and balance on snow by seven subjects and anti-skid device 4, a heel device, as having none or bad walking balance on ice by all ten subjects. Eight subjects walked with a normal muscle function in the hip and knee with all anti-skid devices on all surfaces. Small deviations in walking posture and movements were noted in one to two subjects when walking on different surfaces, but no systematic difference between the devices. Anti-skid device 1 'Rewa', a fixed heel device, was perceived as the most rapid one to take on. All four devices

  11. Development of a Very High Cycle Fatigue (VHCF multiaxial testing device

    Directory of Open Access Journals (Sweden)

    M. Vieira

    2016-07-01

    Full Text Available The very high cycle region of the S-N fatigue curve has been the subject of intensive research on the last years, with special focus on axial, bending, torsional and fretting fatigue tests. Very high cycle fatigue can be achieved using ultrasonic exciters which allow for frequency testing of up to 30 kHz. Still, the multiaxial fatigue analysis is not yet developed for this type of fatigue analyses, mainly due to conceptual limitations of these testing devices. In this paper, a device designed to produce biaxial fatigue testing using a single piezoelectric axial exciter is presented, as well as the preliminary testing of this device. The device is comprised of a horn and a specimen, which are both attached to the piezoelectric exciter. The steps taken towards the final geometry of the device are presented. Preliminary experimental testing of the developed device is made using thermographic imaging, strain measurements and vibration speeds and indicates good behaviour of the tested specimen.

  12. Testing and examination of TMI-2 electrical components and discrete devices

    Energy Technology Data Exchange (ETDEWEB)

    Soberano, F.T.

    1982-11-01

    This report discusses the approach and results of the in situ test conducted on TMI-2 reactor building electrical components and discrete devices. Also included are the necessary presumptions and assumptions to correlate observed anomalies to the accident.

  13. A flexible and robust soft-error testing system for microelectronic devices and integrated circuits

    Institute of Scientific and Technical Information of China (English)

    王晓辉; 杨振雷; 童腾; 苏弘; 刘杰; 张战刚; 古松; 刘天奇; 孔洁; 赵兴文

    2015-01-01

    Single event effects (SEEs) induced by radiations become a significant reliability challenge for modern elec-tronic systems. To evaluate SEEs susceptibility for microelectronic devices and integrated circuits (ICs), an SEE testing system with flexibility and robustness was developed at Heavy Ion Research Facility in Lanzhou (HIRFL). The system is compatible with various types of microelectronic devices and ICs, and supports plenty of complex and high-speed test schemes and plans for the irradiated devices under test (DUTs). Thanks to the combination of meticulous circuit design and the hardened logic design, the system has additional performances to avoid an overheated situation and irradiations by stray radiations. The system has been tested and verified by experiments for irradiating devices at HIRFL.

  14. Device for lengthening of a musculotendinous unit by direct continuous traction in the sheep

    Directory of Open Access Journals (Sweden)

    Zumstein Matthias A

    2012-05-01

    Full Text Available Abstract Background Retraction, atrophy and fatty infiltration are signs subsequent to chronic rotator cuff tendon tears. They are associated with an increased pennation angle and a shortening of the muscle fibers in series. These deleterious changes of the muscular architecture are not reversible with current repair techniques and are the main factors for failed rotator cuff tendon repair. Whereas fast stretching of the retracted musculotendinous unit results in proliferation of non-contractile fibrous tissue, slow stretching may lead to muscle regeneration in terms of sarcomerogenesis. To slowly stretch the retracted musculotendinous unit in a sheep model, two here described tensioning devices have been developed and mounted on the scapular spine of the sheep using an expandable threaded rod, which has been interposed between the retracted tendon end and the original insertion site at the humeral head. Traction is transmitted in line with the musculotendinous unit by sutures knotted on the expandable threaded rod. The threaded rod of the tensioner is driven within the body through a rotating axis, which enters the body on the opposite side. The tendon end, which was previously released (16 weeks prior from its insertion site with a bone chip, was elongated with a velocity of 1 mm/day. Results After several steps of technical improvements, the tensioner proved to be capable of actively stretching the retracted and degenerated muscle back to the original length and to withstand the external forces acting on it. Conclusion This technical report describes the experimental technique for continuous elongation of the musculotendinous unit and reversion of the length of chronically shortened muscle.

  15. A Review on Key Issues and Challenges in Devices Level MEMS Testing

    Directory of Open Access Journals (Sweden)

    Muhammad Shoaib

    2016-01-01

    Full Text Available The present review provides information relevant to issues and challenges in MEMS testing techniques that are implemented to analyze the microelectromechanical systems (MEMS behavior for specific application and operating conditions. MEMS devices are more complex and extremely diverse due to the immersion of multidomains. Their failure modes are distinctive under different circumstances. Therefore, testing of these systems at device level as well as at mass production level, that is, parallel testing, is becoming very challenging as compared to the IC test, because MEMS respond to electrical, physical, chemical, and optical stimuli. Currently, test systems developed for MEMS devices have to be customized due to their nondeterministic behavior and complexity. The accurate measurement of test systems for MEMS is difficult to quantify in the production phase. The complexity of the device to be tested required maturity in the test technique which increases the cost of test development; this practice is directly imposed on the device cost. This factor causes a delay in time-to-market.

  16. Effect of lubricants on friction in laboratory tests of a total disc replacement device.

    Science.gov (United States)

    Moghadas, Parshia; Mahomed, Aziza; Hukins, David W L; Shepherd, Duncan E T

    2013-09-01

    Some designs of total disc replacement devices have articulating bearing surfaces, and these devices are tested in vitro with a lubricant of diluted calf serum. It is believed that the lubricant found in total disc replacement devices in vivo is interstitial fluid that may have properties between that in Ringer's solution and diluted calf serum. To investigate the effect of lubricants, a set of friction tests were performed on a generic model of a metal against metal ball-and-socket total disc replacement device. Two devices were tested: one with a ball radius of 10 mm and other with a ball radius of 16 mm; each device had a radial clearance of 0.015 mm. A spine simulator was used to measure frictional torque for each device in axial rotation, flexion-extension and lateral bending at frequencies of 0.25-2 Hz, under 1200 N axial load. Each device was tested with two different lubricants: a solution of new born calf serum diluted with deionised water and Ringer's solution. The results showed that the frictional torque generated between the bearing surfaces was significantly higher in Ringer's solution than in diluted calf serum. The use of Ringer's solution as a lubricant provides a stringent test condition to detect possible problems. Diluted calf serum is more likely to provide an environment closer to that in vivo. However, the precise properties of the fluid lubricating a total disc replacement device are not known; hence, tests using diluted calf serum may not necessarily give the same results as those obtained in vivo.

  17. 33 CFR 159.126a - Suspended solids test: Type II devices.

    Science.gov (United States)

    2010-07-01

    ... suspended solids in accordance with 40 CFR part 136. The arithmetic mean of the total suspended solids in 38... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Suspended solids test: Type II... Suspended solids test: Type II devices. During the sewage processing test (§ 159.121) 40 effluent samples...

  18. The Effect of Asterisks as an Attention Focusing Device on Test Performance of Undergraduate Students.

    Science.gov (United States)

    Perrin, David W.; Kerasotes, Dean L.

    It was hypothesized that using asterisks as attention focusing devices would cause students to read all asteriked test items more carefully and would improve test scores of undergraduate education students. Sixty-three undergraduates majoring in elementary or special education were administered a 36-item objective test. Asterisks were used to…

  19. Development of Proposed Standards for Testing Solar Collectors and Thermal Storage Devices. NBS Technical Note 899.

    Science.gov (United States)

    Hill, James E.; And Others

    A study has been made at the National Bureau of Standards of the different techniques that are or could be used for testing solar collectors and thermal storage devices that are used in solar heating and cooling systems. This report reviews the various testing methods and outlines a recommended test procedure, including apparatus and…

  20. Functional status of United States children supported with a left ventricular assist device at heart transplantation.

    Science.gov (United States)

    Bulic, Anica; Maeda, Katsuhide; Zhang, Yulin; Chen, Sharon; McElhinney, Doff B; Dykes, John C; Hollander, Amanda M; Hollander, Seth A; Murray, Jenna; Reinhartz, Olaf; Gowan, Mary Alice; Rosenthal, David N; Almond, Christopher S

    2017-08-01

    As survival with pediatric left ventricular assist devices (LVADs) has improved, decisions regarding the optimal support strategy may depend more on quality of life and functional status (FS) rather than mortality alone. Limited data are available regarding the FS of children supported with LVADs. We sought to compare the FS of children supported with LVADs vs vasoactive infusions to inform decision making around support strategies. Organ Procurement and Transplant Network data were used to identify all United States children aged between 1 and 21 years at heart transplant (HT) between 2006 and 2015 for dilated cardiomyopathy and supported with an LVAD or vasoactive infusions alone at HT. FS was measured using the 10-point Karnofsky and Lansky scale. Of 701 children who met the inclusion criteria, 430 (61%) were supported with vasoactive infusions, and 271 (39%) were supported with an LVAD at HT. Children in the LVAD group had higher median FS scores at HT than children in the vasoactive infusion group (6 vs 5, p < 0.001) but lower FS scores at listing (4 vs 6, p < 0.001). The effect persisted regardless of patient location at HT (home, hospital, intensive care) or device type. Discharge by HT occurred in 46% of children in the LVAD group compared with 26% of children in the vasoactive infusion cohort (p = 0.001). Stroke was reported at HT in 3% of children in the LVAD cohort and in 1% in the vasoactive infusion cohort (p = 0.04). Among children with dilated cardiomyopathy undergoing HT, children supported with LVADs at HT have higher FS than children supported with vasoactive infusions at HT, regardless of device type or hospitalization status. Children supported with LVADs at HT were more likely to be discharged from the hospital but had a higher prevalence of stroke at HT. Copyright © 2017 International Society for Heart and Lung Transplantation. Published by Elsevier Inc. All rights reserved.

  1. Microbiological testing of devices used in maintaining peripheral venous catheters.

    Science.gov (United States)

    Rossini, Fernanda de Paula; Andrade, Denise de; Santos, Lissandra Chaves de Sousa; Ferreira, Adriano Menis; Tieppo, Caroline; Watanabe, Evandro

    2017-05-15

    to evaluate the use of peripheral venous catheters based on microbiological analysis of devices (dressing and three-way stopcocks) and thus contribute to the prevention and infection control. this was a prospective study of microbiological analysis of 30 three-way stopcocks (external surfaces and lumens) and 30 dressing used in maintaining the peripheral venous catheters of hospitalized adult patients. all external surfaces, 40% of lumens, and 86.7% of dressing presented bacterial growth. The main species isolated in the lumen were 50% coagulase-negative Staphylococcus, 14.3% Staphylococcus aureus, and 14.3% Pseudomonas aeruginosa. Fifty nine percent of multidrug-resistant bacteria were isolated of the three-way stopcocks, 42% of the lumens, and 44% of the dressing with a predominance of coagulase-negative Staphylococcus resistant to methicillin. Besides, 18% gram-negative bacteria with resistance to carbapenems were identified from multidrug-resistant bacteria on the external surfaces of the three-way stopcocks. it is important to emphasize the isolation of coagulase-negative Staphylococcus and gram-negative bacteria resistant to methicillin and carbapenems in samples of devices, respectively, which reinforces the importance of nursing care in the maintenance of the biologically safe environment as well as prevention and infection control practices. avaliar o uso de cateteres venosos periféricos com base em análises microbiológicas de dispositivos (curativos e torneiras de três vias - T3Vs) e assim contribuir para a prevenção e controle de infecção. estudo prospectivo de análise microbiológica de 30 T3Vs (superfícies externas e lúmens) e 30 curativos utilizados na manutenção dos cateteres venosos periféricos de pacientes adultos hospitalizados. todas as superfícies externas, 40% dos lúmens e 86,7% dos curativos apresentaram crescimento bacteriano. As principais espécies isoladas no lúmen foram 50% Staphylococcus coagulase-negativa, 14

  2. Testing for purchasing power parity in 21 African countries using several unit root tests

    Science.gov (United States)

    Choji, Niri Martha; Sek, Siok Kun

    2017-04-01

    Purchasing power parity is used as a basis for international income and expenditure comparison through the exchange rate theory. However, empirical studies show disagreement on the validity of PPP. In this paper, we conduct the testing on the validity of PPP using panel data approach. We apply seven different panel unit root tests to test the validity of the purchasing power parity (PPP) hypothesis based on the quarterly data on real effective exchange rate for 21 African countries from the period 1971: Q1-2012: Q4. All the results of the seven tests rejected the hypothesis of stationarity meaning that absolute PPP does not hold in those African Countries. This result confirmed the claim from previous studies that standard panel unit tests fail to support the PPP hypothesis.

  3. Digital Measuring Devices Used for Injector Hydraulic Test

    Directory of Open Access Journals (Sweden)

    S. N. Leontiev

    2015-01-01

    Full Text Available To ensure a high specific impulse of the LRE (liquid-propellant engine chamber it is necessary to have optimally organized combustion of the fuel components. This can be ensured by choosing the optimum geometry of gas-dynamic contour of the LRE combustor, as well as by improving the sputtering processes and mixing the fuel components, for example, by selection of the optimum type, characteristics, and location of injectors on the mixing unit of the chamber.These particular reasons arise the interest in the injector characteristics in terms of science, and technological aspects determine the need for control of underlying design parameters in their manufacture.The objective of this work is to give an experimental justification on used digital measurement instrumentation and research the hydraulic characteristics of injectors.To determine injector parameters most widely were used the units with sectional collectors. A technique to control injector parameters using the sectional collectors involves spraying the liquid by injector at a given pressure drop on it for a certain time (the longer, the higher the accuracy and reliability of the results and then determining the amount of liquid in each section to calculate the required parameters of injector.In this work the liquid flow through the injector was determined by high-precision flowmeters FLONET FN2024.1 of electromagnetic type, which have very high metrological characteristics, in particular a flow rate error does not exceed 0.5% in a range of water flow from Qmin= 0.0028 l/s to Qmax Qmax = 0.28 l/s. To determine the coefficient of uneven spray were used differential pressure sensors DMD 331-ASLX of company "DB Sensors RUS", which have an error of 0.075% with a range of differential pressure 0 ... 5 kPa. Measuring complex MIC-200 of company "NPP Measure" and WinPos software for processing array information provided entry, recording, and processing of all the data of the experiment.In this

  4. Radiation Testing, Characterization and Qualification Challenges for Modern Microelectronics and Photonics Devices and Technologies

    Science.gov (United States)

    LaBel, Kenneth A.; Cohn, Lewis M.

    2008-01-01

    At GOMAC 2007, we discussed a selection of the challenges for radiation testing of modern semiconductor devices focusing on state-of-the-art memory technologies. This included FLASH non-volatile memories (NVMs) and synchronous dynamic random access memories (SDRAMs). In this presentation, we extend this discussion in device packaging and complexity as well as single event upset (SEU) mechanisms using several technology areas as examples including: system-on-a-chip (SOC) devices and photonic or fiber optic systems. The underlying goal is intended to provoke thought for understanding the limitations and interpretation of radiation testing results.

  5. A Pull-in Based Test Mechanism for Device Diagnostic and Process Characterization

    Directory of Open Access Journals (Sweden)

    L. A. Rocha

    2008-01-01

    Full Text Available A test technique for capacitive MEMS accelerometers and electrostatic microactuators, based on the measurement of pull-in voltages and resonance frequency, is described. Using this combination of measurements, one can estimate process-induced variations in the device layout dimensions as well as deviations from nominal value in material properties, which can be used either for testing or device diagnostics purposes. Measurements performed on fabricated devices confirm that the 250 nm overetch observed on SEM images can be correctly estimated using the proposed technique.

  6. Numerical distribution functions of fractional unit root and cointegration tests

    DEFF Research Database (Denmark)

    MacKinnon, James G.; Nielsen, Morten Ørregaard

    We calculate numerically the asymptotic distribution functions of likelihood ratio tests for fractional unit roots and cointegration rank. Because these distributions depend on a real-valued parameter, b, which must be estimated, simple tabulation is not feasible. Partly due to the presence...... of this parameter, the choice of model specification for the response surface regressions used to obtain the numerical distribution functions is more involved than is usually the case. We deal with model uncertainty by model averaging rather than by model selection. We make available a computer program which, given...

  7. An open-source framework for testing tracking devices using Lego Mindstorms

    Science.gov (United States)

    Jomier, Julien; Ibanez, Luis; Enquobahrie, Andinet; Pace, Danielle; Cleary, Kevin

    2009-02-01

    In this paper, we present an open-source framework for testing tracking devices in surgical navigation applications. At the core of image-guided intervention systems is the tracking interface that handles communication with the tracking device and gathers tracking information. Given that the correctness of tracking information is critical for protecting patient safety and for ensuring the successful execution of an intervention, the tracking software component needs to be thoroughly tested on a regular basis. Furthermore, with widespread use of extreme programming methodology that emphasizes continuous and incremental testing of application components, testing design becomes critical. While it is easy to automate most of the testing process, it is often more difficult to test components that require manual intervention such as tracking device. Our framework consists of a robotic arm built from a set of Lego Mindstorms and an open-source toolkit written in C++ to control the robot movements and assess the accuracy of the tracking devices. The application program interface (API) is cross-platform and runs on Windows, Linux and MacOS. We applied this framework for the continuous testing of the Image-Guided Surgery Toolkit (IGSTK), an open-source toolkit for image-guided surgery and shown that regression testing on tracking devices can be performed at low cost and improve significantly the quality of the software.

  8. A review of Doppler ultrasound quality assurance protocols and test devices.

    Science.gov (United States)

    Browne, Jacinta E

    2014-11-01

    In this paper, an overview of Doppler ultrasound quality assurance (QA) testing will be presented in three sections. The first section will review the different Doppler ultrasound parameters recommended by professional bodies for use in QA protocols. The second section will include an evaluation and critique of the main test devices used to assess Doppler performance, while the final section of this paper will discuss which of the wide range of test devices have been found to be most suitable for inclusion in Doppler QA programmes. Pulsed Wave Spectral Doppler, Colour Doppler Imaging QA test protocols have been recommended over the years by various professional bodies, including the UK's Institute of Physics and Engineering in Medicine (IPEM), the American Institute for Ultrasound in Medicine (AIUM), and the International Electrotechnical Commission (IEC). However, despite the existence of such recommended test protocols, very few commercial or research test devices exist which can measure the full range of both PW Doppler ultrasound and colour Doppler imaging performance parameters, particularly quality control measurements such as: (i) Doppler sensitivity (ii) colour Doppler spatial resolution (iii) colour Doppler temporal resolution (iv) colour Doppler velocity resolution (v) clutter filter performance and (vi) tissue movement artefact suppression. In this review, the merits of the various commercial and research test devices will be considered and a summary of results obtained from published studies which have made use of some of these Doppler test devices, such as the flow, string, rotating and belt phantom, will be presented.

  9. ASTROD I - Astrodynamical Space Test of Relativity using Optical Devices

    Science.gov (United States)

    Selig, Hanns; Ni, Wei-Tou; Laemmerzahl, Claus

    In 2011 ASTROD I has been selected as one of the final 14 candidates for the Cosmic Vision M3 mission. ASTROD I is a planned interplanetary space mission with multiple goals. The primary aims are: to test general relativity with an improvement in sensitivity of over three orders of magnitude, improving our understanding of gravity and aiding the development of a new quantum gravity theory; to measure key solar system parameters with increased accuracy, advancing solar physics and our knowledge of the solar system; and to measure the time rate of change of the gravitational constant with an order of magnitude improvement and probing dark matter and dark energy gravitationally. It is an international project, and is envisaged as the first in a series of ASTROD missions. ASTROD I will consist of one spacecraft carrying a telescope, four lasers, two event timers and a clock. Two-way, two-wavelength laser pulse ranging will be used between the spacecraft in a solar orbit and deep space laser stations on Earth, to achieve the ASTROD I goals. Finally the mission was not selected for the final 4 candidates for CV M3 in 2011. Nevertheless, ASTROD is a very promising concept for a fundamental physics space mission and shares some key technologies with other popular space missions like LISA and Jason 2 (T2L2). We have also considered possibilities (i) to add an ASTROD I laser ranging package to other fundamental missions for testing the dynamics of relativistic gravity; (ii) to fully combine ASTROD I with another fundamental mission using basic technology of the LISA Pathfiner (this could also be good for a LISA-type mission scheduled to launch 20 years later). In this paper, we present various possibilities of our study.

  10. DEVELOPMENT AND TESTING TOOL FOR PAPER HANDLING AND/OR PRINTER DEVICES

    Directory of Open Access Journals (Sweden)

    H. Gutiérrez

    2003-04-01

    Full Text Available A useful development and testing tool for Hewlett Packard paper handling and/or printer devices is presented.The system provides a microprocessor based general architecture integrated by two PCB cards and asoftware application, used to improve new product design and testing. Paper handling devices operation isbased on DC motors, stepper motors and sensors components, so a graphical user interface was developedin order to configure, drive, and test them. The implemented tool allows a time reduction greater than 50% forthe development and test of prototypes.

  11. Corrective Action Investigation Plan for Corrective Action Unit 375: Area 30 Buggy Unit Craters, Nevada Test Site, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Patrick Matthews

    2010-03-01

    Corrective Action Unit (CAU) 375 is located in Areas 25 and 30 of the Nevada Test Site, which is approximately 65 miles northwest of Las Vegas, Nevada. Corrective Action Unit 375 comprises the two corrective action sites (CASs) listed below: • 25-23-22, Contaminated Soils Site • 30-45-01, U-30a, b, c, d, e Craters Existing information on the nature and extent of potential contamination present at the CAU 375 CASs is insufficient to evaluate and recommend corrective action alternatives (CAAs). This document details an investigation plan that will provide for the gathering of sufficient information to evaluate and recommend CAAs. Corrective Action Site 25-23-22 is composed of the releases associated with nuclear rocket testing at Test Cell A (TCA). Test Cell A was used to test and develop nuclear rocket motors as part of the Nuclear Rocket Development Station from its construction in 1958 until 1966, when rocket testing began being conducted at Test Cell C. The rocket motors were built with an unshielded nuclear reactor that produced as much as 1,100 kilowatts (at full power) to heat liquid hydrogen to 4,000 degrees Fahrenheit, at which time the expanded gases were focused out a nozzle to produce thrust. The fuel rods in the reactor were not clad and were designed to release fission fragments to the atmosphere, but due to vibrations and loss of cooling during some operational tests, fuel fragments in excess of planned releases became entrained in the exhaust and spread in the immediate surrounding area. Cleanup efforts have been undertaken at times to collect the fuel rod fragments and other contamination. Previous environmental investigations in the TCA area have resulted in the creation of a number of use restrictions. The industrial area of TCA is encompassed by a fence and is currently posted as a radioactive material area. Corrective Action Site 30-45-01 (releases associated with the Buggy Plowshare test) is located in Area 30 on Chukar Mesa. It was a

  12. Evaluation of ten oral fluid point-of-collection drug-testing devices.

    Science.gov (United States)

    Walsh, J Michael; Crouch, Dennis J; Danaceau, Jonathan P; Cangianelli, Leo; Liddicoat, Laura; Adkins, Randy

    2007-01-01

    Previously, the laboratory evaluations of six point-of-collection oral fluid (POC-OF) drug testing devices were reported. Four additional devices, Oralstat (American Bio Medica); SmartClip (Envitec); Impact (LifePoint); and OraLine IV s.a.t (Sun Biomedical Laboratories), were recently evaluated for their ability to meet the claimed (and proposed) cutoff concentrations set by the manufacturers for the detection of amphetamine(s), cocaine/metabolite, opiates, and cannabinoids (Oralstat also benzodiazepines). With the exception of the Sun Biomedical device, actual false-positive results were not encountered. Most devices performed well for the detection of opiates and amphetamine(s), but approximately half had amphetamine(s) cutoff concentrations greater than that proposed by the Substance Abuse and Mental Health Services Administration (SAMHSA). Only three devices had cocaine cutoffs less than or equal to 20 ng/mL (SAMHSA), and a number of false-negative results were obtained. The devices still were not capable of detecting Delta(9)-tetrahydrocannabinol at 4 ng/mL (SAMHSA). However, sensitivities improved since the initial studies, and approximately half of the devices met the THC-COOH cutoff proposed by SAMHSA. Results from the current and previous evaluations are presented in the paper and indicate that the sensitivity and performance of commercial OF drug testing devices is improving, but remains problematic for the reliable detection of cannabinoid use.

  13. Test method of frequency response based on diamond surface acoustic wave devices

    Institute of Scientific and Technical Information of China (English)

    CHEN Xi-ming; YANG Bao-he; WU Xiao-guo; WU Yi-zhuo

    2011-01-01

    In order to reduce the noises affixed to the signals when testing high frequency devices, a single-port test mode (S11) is used to test frequency response of high frequency (GHz) and dual-port surface acoustic wave devices (SAWDs) in this paper.The feasibility of the test is proved by simulating the Fabry-Perot model. The frequency response of the high-frequency dual-port resonant-type diamond SAWD is measured by S11 and the dual-port test mode (S21), respectively. The results show that the quality factor of the device is 51.29 and the 3 dB bandwidth is 27.8 MHz by S11 -mode measurement, which is better than the S21 mode, and is consistent with the frequency response curve by simulation.

  14. From in vivo to in vitro: The medical device testing paradigm shift.

    Science.gov (United States)

    Kerecman Myers, Dayna; Goldberg, Alan M; Poth, Albrecht; Wolf, Michael F; Carraway, Joseph; McKim, James; Coleman, Kelly P; Hutchinson, Richard; Brown, Ronald; Krug, Harald F; Bahinski, Anthony; Hartung, Thomas

    2017-05-25

    Amid growing efforts to advance the replacement, reduction, and refinement of the use of animals in research, there is a growing recognition that in vitro testing of medical devices can be more effective, both in terms of cost and time, and also more reliable than in vivo testing. Although the technological landscape has evolved rapidly in support of these concepts, regulatory acceptance of alternative testing methods has not kept pace. Despite the acceptance by regulators of some in vitro tests (cytotoxicity, gene toxicity, and some hemocompatibility assays), many toxicity tests still rely on animals (irritation, sensitization, acute toxicity, reproductive/developmental toxicity), even where other industrial sectors have already abandoned them. Bringing about change will require a paradigm shift in current approaches to testing - and a concerted effort to generate better data on risks to human health from exposure to leachable chemicals from medical devices, and to boost confidence in devices and alternative testing methods. To help advance these ideas, stir debate about best practices, and coalesce around a roadmap forward, the JHU-Center for Alternatives to Animal Testing (CAAT) hosted a symposium in Baltimore, Maryland, in December 2013 - believed to be the first gathering dedicated to the topic of in vitro testing of medical devices. Industry representatives, academics, and regulators in attendance presented evidence to support the unique strengths and challenges associated with the approaches currently in use as well as new methods under development, and drew next steps to push the field forward from their presentations and discussion.

  15. Procedural Tests for Anti-G Protective Devices. Volume II. G-Sensitivity Tests

    Science.gov (United States)

    1979-12-01

    applications (2,4). This high purity carbon, having extremely low chemical reactivity, is presently being used in human subjects for prosthesis , cardiac...assist devices, dental implants, and percutaneous lead devices. The fact that high purity carbon is biologically inert is well documented (2-4,8,10), and...New England College, Henniker, N.H.). No. 2 (part 1), 41-47, 1971. 3. Bokros, J. C., et al. Prosthesis made of carbon. Chemtech 7:40-49 (1977). 4

  16. Design of a laboratory hydraulic device for testing of hydraulic pumps

    Directory of Open Access Journals (Sweden)

    Pavel Máchal

    2013-01-01

    Full Text Available The present contribution deals with solves problem of research of testing device to monitor of hydrostatic pumps durability about dynamic loading under laboratory conditions. When carrying out the design of testing device are based on load characteristics of tractor hydraulic circuit, the individual characteristics of hydraulic components and performed calculations. Load characteristics on the tractors CASE IH Magnum 310, JOHN DEERE 8100, ZETOR FORTERRA 114 41 and Fendt 926 Vario were measured. Design of a hydraulic laboratory device is based on the need for testing new types of hydraulic pumps or various types of hydraulic fluids. When creating of hydraulic device we focused on testing hydraulic pumps used in agricultural and forestry tractors. Proportional pressure control valve is an active member of the hydraulic device, which provides change of a continuous control signal into relative pressure of operating fluid. The advantage of a designed hydraulic system is possibility of simulation of dynamic operating loading, which is obtained by measurement under real conditions, and thereby creates laboratory conditions as close to real conditions as possible. The laboratory device is constructed at the Department of Transport and Handling, Faculty of Engineering, Slovak University of Agriculture in Nitra.

  17. Performance of a continuous flow ventricular assist device: magnetic bearing design, construction, and testing.

    Science.gov (United States)

    Allaire, P; Hilton, E; Baloh, M; Maslen, E; Bearnson, G; Noh, D; Khanwilkar, P; Olsen, D

    1998-06-01

    A new centrifugal continuous flow ventricular assist device, the CFVAD III, which is fully magnetic bearing suspended, has been developed. It has only one moving part (the impeller), has no contact (magnetic suspension), is compact, and has minimal heating. A centrifugal impeller of 2 inch outer diameter is driven by a permanent magnet brushless DC motor. This paper discusses the design, construction, testing, and performance of the magnetic bearings in the unit. The magnetic suspension consists of an inlet side magnetic bearing and an outlet side magnetic bearing, each divided into 8 pole segments to control axial and radial displacements as well as angular displacements. The magnetic actuators are composed of several different materials to minimize size and weight while having sufficient load capacity to support the forces on the impeller. Flux levels in the range of 0.1 T are employed in the magnetic bearings. Self sensing electronic circuits (without physical sensors) are employed to determine the impellar position and provide the feedback control signal needed for the magnetic bearing control loops. The sensors provide position sensitivity of approximately 0.025 mm. A decentralized 5 axis controller has been developed using modal control techniques. Proportional integral derivative controls are used for each axis to levitate the magnetically supported impeller.

  18. Radiation Tolerance Qualification Tests of the Final Source Interface Unit for the ALICE Experiment

    CERN Document Server

    Dénes, E; Futó, E; Kerék, A; Kiss, T; Molnár, J; Novák, D; Soós, C; Tölyhi, T; Van de Vyvre, P

    2007-01-01

    The ALICE Detector Data Link (DDL) is a high-speed optical link designed to interface the readout electronics of ALICE sub-detectors to the DAQ computers. The Source Interface Unit (SIU) of the DDL will operate in radiation environment. Previous tests showed that a configuration loss of SRAM-based FPGA devices may happen and the frequency of undetected data errors in the FPGA user memory area is also not acceptable. Therefore, we redesigned the SIU card using another FPGA based on flash technology. In order to detect bit errors in the user memory we added parity check logic to the design. The new SIU has been extensively tested using neutron and proton irradiation to verify its radiation tolerance. In this paper we summarize the design changes, introduce the final design, and the results of the radiation tolerance measurements on the final card.

  19. High-energy heavy ion testing of VLSI devices for single event upsets and latch up

    Indian Academy of Sciences (India)

    S B Umesh; S R Kulkarni; R Sandhya; G R Joshi; R Damle; M Ravindra

    2005-08-01

    Several very large scale integrated (VLSI) devices which are not available in radiation hardened version are still required to be used in spacecraft systems. Thus these components need to be tested for highenergy heavy ion irradiation to find out their tolerance and suitability in specific space applications. This paper describes the high-energy heavy ion radiation testing of VLSI devices for single event upset (SEU) and single event latch up (SEL). The experimental set up employed to produce low flux of heavy ions viz. silicon (Si), and silver (Ag), for studying single event effects (SEE) is briefly described. The heavy ion testing of a few VLSI devices is performed in the general purpose scattering chamber of the Pelletron facility, available at Nuclear Science Centre, New Delhi. The test results with respect to SEU and SEL are discussed.

  20. How Does Medical Device Regulation Perform in the United States and the European Union? A Systematic Review

    Science.gov (United States)

    Kramer, Daniel B.; Xu, Shuai; Kesselheim, Aaron S.

    2012-01-01

    Background Policymakers and regulators in the United States (US) and the European Union (EU) are weighing reforms to their medical device approval and post-market surveillance systems. Data may be available that identify strengths and weakness of the approaches to medical device regulation in these settings. Methods and Findings We performed a systematic review to find empirical studies evaluating medical device regulation in the US or EU. We searched Medline using two nested categories that included medical devices and glossary terms attributable to the US Food and Drug Administration and the EU, following PRISMA guidelines for systematic reviews. We supplemented this search with a review of the US Government Accountability Office online database for reports on US Food and Drug Administration device regulation, consultations with local experts in the field, manual reference mining of selected articles, and Google searches using the same key terms used in the Medline search. We found studies of premarket evaluation and timing (n = 9), studies of device recalls (n = 8), and surveys of device manufacturers (n = 3). These studies provide evidence of quality problems in pre-market submissions in the US, provide conflicting views of device safety based largely on recall data, and relay perceptions of some industry leaders from self-surveys. Conclusions Few studies have quantitatively assessed medical device regulation in either the US or EU. Existing studies of US and EU device approval and post-market evaluation performance suggest that policy reforms are necessary for both systems, including improving classification of devices in the US and promoting transparency and post-market oversight in the EU. Assessment of regulatory performance in both settings is limited by lack of data on post-approval safety outcomes. Changes to these device approval and post-marketing systems must be accompanied by ongoing research to ensure that there is better assessment of

  1. How does medical device regulation perform in the United States and the European union? A systematic review.

    Directory of Open Access Journals (Sweden)

    Daniel B Kramer

    Full Text Available BACKGROUND: Policymakers and regulators in the United States (US and the European Union (EU are weighing reforms to their medical device approval and post-market surveillance systems. Data may be available that identify strengths and weakness of the approaches to medical device regulation in these settings. METHODS AND FINDINGS: We performed a systematic review to find empirical studies evaluating medical device regulation in the US or EU. We searched Medline using two nested categories that included medical devices and glossary terms attributable to the US Food and Drug Administration and the EU, following PRISMA guidelines for systematic reviews. We supplemented this search with a review of the US Government Accountability Office online database for reports on US Food and Drug Administration device regulation, consultations with local experts in the field, manual reference mining of selected articles, and Google searches using the same key terms used in the Medline search. We found studies of premarket evaluation and timing (n = 9, studies of device recalls (n = 8, and surveys of device manufacturers (n = 3. These studies provide evidence of quality problems in pre-market submissions in the US, provide conflicting views of device safety based largely on recall data, and relay perceptions of some industry leaders from self-surveys. CONCLUSIONS: Few studies have quantitatively assessed medical device regulation in either the US or EU. Existing studies of US and EU device approval and post-market evaluation performance suggest that policy reforms are necessary for both systems, including improving classification of devices in the US and promoting transparency and post-market oversight in the EU. Assessment of regulatory performance in both settings is limited by lack of data on post-approval safety outcomes. Changes to these device approval and post-marketing systems must be accompanied by ongoing research to ensure that there is

  2. Portable Upconversion Nanoparticles-Based Paper Device for Field Testing of Drug Abuse.

    Science.gov (United States)

    He, Mengyuan; Li, Zhen; Ge, Yiying; Liu, Zhihong

    2016-02-01

    We report the first portable upconversion nanoparticles (UCNPs)-based paper device for road-side field testing of cocaine. Upon the recognition of cocaine by two pieces of rationally designed aptamer fragments, the luminescence of UCNPs immobilized on the paper is quenched by Au nanoparticles (AuNPs), which indicates the cocaine concentration. This device can give quantitative results in a short time with high sensitivity using only a smartphone as the apparatus. Moreover, this device is applicable in human saliva samples, and it also can be used to monitor the cocaine content change in blood samples. The results of this work demonstrate the prospect of developing UCNPs-based paper devices for field testing of drug abuse.

  3. Testing designing an electrical device compliant with the electromagnetic compatibility directive

    Science.gov (United States)

    Płaczek, M.; Maćkowski, M.; Nowak, P.

    2017-08-01

    The goal of presented work was to build an electronic device in order to test the effectiveness of different EMC-improving solutions. Three EMC tests were done in order to check the created device compliance with the electromagnetic compatibility directive. Each of them was conducted for both industrial and non-industrial parameters (voltage and field strength), according to IEC PN-EN 61000 standards. Three tests were done: conductive immunity test in EM clamp, radiated immunity test in GTEM chamber, radiated emission test in GTEM chamber. Firstly, the device’s conductive immunity was examined. The set of possible solutions was created by examining existing designs, papers, books and producers’ recommendations. In result, different component configurations were chosen to determine the most EMC-effective one. Next, electromagnetic compatibility of proposed device configurations was tested in the GTEM chamber (radiated immunity and radiated emission). Tests results are presented on charts and analysed in order to verify if designed device face requirements of the electromagnetic compatibility directive. It was verify which of proposed electromagnetic compatibility improving solutions can solve problems with electromagnetic compatibility.

  4. 77 FR 17457 - Work Group on Alternative Test Methods for Commercial Measuring Devices

    Science.gov (United States)

    2012-03-26

    ... National Institute of Standards and Technology Work Group on Alternative Test Methods for Commercial...: The National Institute of Standards and Technology (NIST) is forming a Work Group (WG) to examine alternative methods for testing the accuracy of commercial measuring devices including, but not limited...

  5. 49 CFR 192.731 - Compressor stations: Inspection and testing of relief devices.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Compressor stations: Inspection and testing of...) PIPELINE SAFETY TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Maintenance § 192.731 Compressor stations: Inspection and testing of relief devices. (a) Except for rupture...

  6. Assessment of Current Practice for Tank Testing of Small Marine Energy Devices

    DEFF Research Database (Denmark)

    Kofoed, Jens Peter; Frigaard, Peter

    Discussion Report. Equitable Testing and Evaluation of Marine Energy Extraction Devices in terms of Performance, Cost and Environmental Impact. The report is a contribution by Aalborg University (AAU) to the deliverable on Assessment of current practice for tank testing of small marine energy...

  7. Fabrication and testing history prototypes and production units

    Energy Technology Data Exchange (ETDEWEB)

    1954-09-01

    From April, 1951 to Aug, 1954, New York Shipbuilding Corp. carried out a subcontract with E.I. du Pont de Nemours & Company that was without parallel in the shipyard`s history. The work, designated the NYX Project for reasons of security, was vital to the operations of the Savannah River Plant, Aiken, S.C., which was then being designed and constructed by du Pont for the Atomic Energy Commission. It consisted of three broad parts: developmental and experimental work; fabrication and testing of a prototype unit; fabrication of production units. Five production units were ultimately built, one of them converted from the prototype. All were fabricated from stainless steel, and involved welding techniques, control of thermal distortion and tolerances never previously attempted on assemblies of comparable size. Du Pont`s technical experience and the background of New York Ship in heavy construction, particularly in the fabrication of naval gun turrets, were combined from the outset to resolve the difficult fabrication problems that occurred almost daily. Representatives of both companies worked together as a team in the shops and at supervisory levels to an unprecedented extent. The report is intended primarily to summarize New York Ship`s part in the project, but also includes some of du Pont`s activities since the work of the two organizations was so interrelated. Because of the scope of the program, it will not always be possible to provide detailed information, but rather to record what happened in general terms. Where the reader desires more specific data, he should refer to original plans and records, including various reports compiled during the course of the project.

  8. Improved CPAS Photogrammetric Capabilities for Engineering Development Unit (EDU) Testing

    Science.gov (United States)

    Ray, Eric S.; Bretz, David R.

    2013-01-01

    This paper focuses on two key improvements to the photogrammetric analysis capabilities of the Capsule Parachute Assembly System (CPAS) for the Orion vehicle. The Engineering Development Unit (EDU) system deploys Drogue and Pilot parachutes via mortar, where an important metric is the muzzle velocity. This can be estimated using a high speed camera pointed along the mortar trajectory. The distance to the camera is computed from the apparent size of features of known dimension. This method was validated with a ground test and compares favorably with simulations. The second major photogrammetric product is measuring the geometry of the Main parachute cluster during steady-state descent using onboard cameras. This is challenging as the current test vehicles are suspended by a single-point attachment unlike earlier stable platforms suspended under a confluence fitting. The mathematical modeling of fly-out angles and projected areas has undergone significant revision. As the test program continues, several lessons were learned about optimizing the camera usage, installation, and settings to obtain the highest quality imagery possible.

  9. Method of Harmonic Balance in Full-Scale-Model Tests of Electrical Devices

    Science.gov (United States)

    Gorbatenko, N. I.; Lankin, A. M.; Lankin, M. V.

    2017-01-01

    Methods for determining the weber-ampere characteristics of electrical devices, one of which is based on solution of direct problem of harmonic balance and the other on solution of inverse problem of harmonic balance by the method of full-scale-model tests, are suggested. The mathematical model of the device is constructed using the describing function and simplex optimization methods. The presented results of experimental applications of the method show its efficiency. The advantage of the method is the possibility of application for nondestructive inspection of electrical devices in the processes of their production and operation.

  10. Evaluation of 3 dental unit waterline contamination testing methods.

    Science.gov (United States)

    Porteous, Nuala; Sun, Yuyu; Schoolfield, John

    2015-01-01

    Previous studies have found inconsistent results from testing methods used to measure heterotrophic plate count (HPC) bacteria in dental unit waterline (DUWL) samples. This study used 63 samples to compare the results obtained from an in-office chairside method and 2 currently used commercial laboratory HPC methods (Standard Methods 9215C and 9215E). The results suggest that the Standard Method 9215E is not suitable for application to DUWL quality monitoring, due to the detection of limited numbers of heterotrophic organisms at the required 35°C incubation temperature. The results also confirm that while the in-office chairside method is useful for DUWL quality monitoring, the Standard Method 9215C provided the most accurate results.

  11. Design and test hardware for a solar array switching unit

    Science.gov (United States)

    Patil, A. R.; Cho, B. H.; Sable, D.; Lee, F. C.

    1992-01-01

    This paper describes the control of a pulse width modulated (PWM) type sequential shunt switching unit (SSU) for spacecraft applications. It is found that the solar cell output capacitance has a significant impact on SSU design. Shorting of this cell capacitance by the PWM switch causes input current surges. These surges are minimized by the use of a series filter inductor. The system with a filter is analyzed for ripple and the control to output-voltage transfer function. Stable closed loop design considerations are discussed. The results are supported by modeling and measurements of loop gain and of closed-loop bus impedance on test hardware for NASA's 120 V Earth Observation System (EOS). The analysis and modeling are also applicable to NASA's 160 V Space Station power system.

  12. SU-E-P-46: Clinical Acceptance Testing and Implementation of a Portable CT Unit

    Energy Technology Data Exchange (ETDEWEB)

    LaFrance, M; Marsh, S; Hicks, R; O’Donnell-Moran, G [Baystate Health Systems, Inc., Springfield, MA (United States)

    2015-06-15

    Purpose: Planning for the first installation in New England of a new portable CT unit to be used in the Operating Room required the integration of many departments including Surgery, Neurosurgery, Information Services, Clinical Engineering, Radiology and Medical Physics/Radiation Safety. Acceptance testing and the quality assurance procedures were designed to optimize image quality and patient and personnel radiation exposure. Methods: The vendor’s protocols were tested using the CT Dosimetry phantoms. The system displayed the CTDIw instead of the CTDIvol while testing the unit. Radiation exposure was compared to existing CT scanners from installed CT units throughout the facility. Brainlab measures all 4 periphery slots on the CT Dosimetry phantom. The ACR measures only the superior slot for the periphery measurement. A comprehensive radiation survey was also performed for several locations. Results: The CTDIvol measurements were comparable for the following studies: brain, C-Spine, and sinuses. However, the mobile CT measurements were slightly higher than other CT units but within acceptable tolerance if measured using the ACR method.Based on scatter measurements, it was determined if any personnel were to stay in the OR Suite during image acquisition that the appropriate lead apron and thyroid shields had to be worn.In addition, to reduce unnecessary scatter, there were two mobile 6 foot wide shields (1/16″ lead equivalent) available to protect personnel in the room and adjacent areas. Conclusion: Intraoperative CT provides the physician new opportunities for evaluation of the progression of surgical resections and device placement at the cost of increasing the amount of trained personnel required to perform this procedure. It also brings with it challenges to keep the radiation exposure to the patients and staff within reasonable limits.

  13. Research on the overload protection reliability of moulded case circuit-breakers and its test device

    Institute of Scientific and Technical Information of China (English)

    LI Kui; LU Jian-guo; WU Yi; QIN Zhi-jun; YAO Dong-mei

    2007-01-01

    This paper analyzed the reliability and put forward the reliability index of overload protection for moulded case circuit breaker. The success rate was adopted as its reliability index of overload protection. Based on the reliability index and the reliability level, the reliability examination plan was analyzed and a test device for the overload protection of moulded case circuit-breaker was developed. In the reliability test of overload protection, two power sources were used, which reduced the time of conversion and regulation between two different test currents in the overload protection test, which made the characteristic test more accurate. The test device was designed on the base of a Windows system, which made its operation simple and friendly.

  14. Electromagnetic radiation from VDT units: study of the effectiveness of an active shielding device.

    Science.gov (United States)

    Sisto, R; Casciardi, S; Giliberti, C; Moleti, A

    1999-01-01

    Measurements of extremely low frequency electromagnetic fields and low frequency magnetic fields emitted by a set of video display terminal (VDT) units are reported. The field values measured at the position normally occupied by the user are below the safety limits. This is because the field amplitudes decrease rapidly (following a 1/R3 law) with the distance from the source, as has been verified in this work. Measurements with a commercial shielding device consisting of small plastic balls filled with a water solution of rare earth elements were also performed. The only physical mechanism that could be hypothesized to produce an active suppression of the VDT field is that rare earth atoms, which probably were chosen due to their large magnetic moment, behave as oscillating magnetic dipoles capable of emitting a secondary magnetic field that, along some particular directions, has a phase that is opposite to that of the exciting field. Unfortunately, if one analyzes this mechanism quantitatively, it is easy to show that the secondary magnetic field is absolutely negligible, as was confirmed by experimental measurements performed in this study.

  15. Integrated base stations and a method of transmitting data units in a communications system for mobile devices

    NARCIS (Netherlands)

    Bosch, H.G.P.; Mullender, Sape J.; Narlikar, G.J.; Samuel, L.G.; Yagati, L.N.

    2006-01-01

    Integrated base stations and a method of transmitting data units in a communications system for mobile devices. In one embodiment, an integrated base station includes a communications processor having a protocol stack configured with a media access control layer and a physical layer.

  16. Selected fault testing of electronic isolation devices used in nuclear power plant operation

    Energy Technology Data Exchange (ETDEWEB)

    Villaran, M.; Hillman, K.; Taylor, J.; Lara, J.; Wilhelm, W. [Brookhaven National Lab., Upton, NY (United States)

    1994-05-01

    Electronic isolation devices are used in nuclear power plants to provide electrical separation between safety and non-safety circuits and systems. Major fault testing in an earlier program indicated that some energy may pass through an isolation device when a fault at the maximum credible potential is applied in the transverse mode to its output terminals. During subsequent field qualification testing of isolators, concerns were raised that the worst case fault, that is, the maximum credible fault (MCF), may not occur with a fault at the maximum credible potential, but rather at some lower potential. The present test program investigates whether problems can arise when fault levels up to the MCF potential are applied to the output terminals of an isolator. The fault energy passed through an isolated device during a fault was measured to determine whether the levels are great enough to potentially damage or degrade performance of equipment on the input (Class 1E) side of the isolator.

  17. Near Earth Asteroid Solar Sail Engineering Development Unit Test Program

    Science.gov (United States)

    Lockett, Tiffany Russell; Few, Alexander; Wilson, Richard

    2017-01-01

    The Near Earth Asteroid (NEA) Scout project is a 30x20x10cm (6U) cubesat reconnaissance mission to investigate a near Earth asteroid utilizing an 86m2 solar sail as the primary propulsion system. This will be the largest solar sail NASA will launch to date. NEA Scout is a secondary payload currently manifested on the maiden voyage of the Space Launch System in 2018. In development of the solar sail subsystem, design challenges were identified and investigated for packaging within a 6U form factor and deployment in cis-lunar space. Analysis furthered understanding of thermal, stress, and dynamics of the stowed system and matured an integrated sail membrane model for deployed flight dynamics. This paper will address design, fabrication, and lessons learned from the NEA Scout solar sail subsystem engineering development unit. From optical properties of the sail material to folding and spooling the single 86m2 sail, the team has developed a robust deployment system for the solar sail. This paper will also address expected and received test results from ascent vent, random vibration, and deployment tests.

  18. Fission Surface Power Technology Demonstration Unit Test Results

    Science.gov (United States)

    Briggs, Maxwell H.; Gibson, Marc A.; Geng, Steven M.; Sanzi, James L.

    2016-01-01

    The Fission Surface Power (FSP) Technology Demonstration Unit (TDU) is a system-level demonstration of fission power technology intended for use on manned missions to Mars. The Baseline FSP systems consists of a 190 kWt UO2 fast-spectrum reactor cooled by a primary pumped liquid metal loop. This liquid metal loop transfers heat to two intermediate liquid metal loops designed to isolate fission products in the primary loop from the balance of plant. The intermediate liquid metal loops transfer heat to four Stirling Power Conversion Units (PCU), each of which produce 12 kWe (48 kW total) and reject waste heat to two pumped water loops, which transfer the waste heat to titanium-water heat pipe radiators. The FSP TDU simulates a single leg of the baseline FSP system using an electrically heater core simulator, a single liquid metal loop, a single PCU, and a pumped water loop which rejects the waste heat to a Facility Cooling System (FCS). When operated at the nominal operating conditions (modified for low liquid metal flow) during TDU testing the PCU produced 8.9 kW of power at an efficiency of 21.7 percent resulting in a net system power of 8.1 kW and a system level efficiency of 17.2 percent. The reduction in PCU power from levels seen during electrically heated testing is the result of insufficient heat transfer from the NaK heater head to the Stirling acceptor, which could not be tested at Sunpower prior to delivery to the NASA Glenn Research Center (GRC). The maximum PCU power of 10.4 kW was achieved at the maximum liquid metal temperature of 875 K, minimum water temperature of 350 K, 1.1 kg/s liquid metal flow, 0.39 kg/s water flow, and 15.0 mm amplitude at an efficiency of 23.3 percent. This resulted in a system net power of 9.7 kW and a system efficiency of 18.7 percent.

  19. Frontline immunochromatographic device for on-site urine testing of amphetamines: laboratory validation using authentic specimens.

    Science.gov (United States)

    Beck, O; Kraft, M; Moeller, M R; Smith, B L; Schneider, S; Wennig, R

    2000-03-01

    We evaluated a new test device for amphetamines and methamphetamines (Frontline, cut-off limit 300 ng/mL) using authentic clinical and forensic specimens. The device is based on immunochromatography and is dipped into urine and read visually by comparison with a colour scale after a few minutes. A total of 658 specimens were tested by comparing results of the screening procedure with established immunoassays. Discordant results were further investigated by gas chromatography mass spectrometry or gas chromatography (with flame ionization detector). The Frontline device had a sensitivity of 93% and a specificity of 98%. When specimens were classified by urine amphetamine concentration, close agreement was obtained at concentrations below 150 ng/mL and above 1000 ng/mL. A small number of specimens with amphetamine concentrations between 300 and 1000 ng/mL tested negative in the Frontline test. This finding could to some extent be explained by the enantioselectivity of the antibodies in the Frontline test to d-amphetamine. We conclude that the performance of the Frontline test device for amphetamines is adequate for presumptive clinical and forensic screening.

  20. 77 FR 38857 - Design, Inspection, and Testing Criteria for Air Filtration and Adsorption Units of Normal...

    Science.gov (United States)

    2012-06-29

    ... COMMISSION Design, Inspection, and Testing Criteria for Air Filtration and Adsorption Units of Normal..., Inspection, and Testing Criteria for Air Filtration and Adsorption Units of Normal Atmosphere Cleanup Systems..., entitled, ``Design, Inspection, and Testing Criteria for Air Filtration and Adsorption Units of...

  1. Closure Report for Corrective Action Unit 543: Liquid Disposal Units, Nevada Test Site, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environmental Restoration

    2008-01-01

    This Closure Report (CR) documents closure activities for Corrective Action Unit (CAU) 543, Liquid Disposal Units, according to the Federal Facility Agreement and Consent Order (FFACO, 1996) and the Corrective Action Plan (CAP) for CAU 543 (U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office [NNSA/NSO], 2007). CAU 543 is located at the Nevada Test Site (NTS), Nevada (Figure 1), and consists of the following seven Corrective Action Sites (CASs): CAS 06-07-01, Decon Pad; CAS 15-01-03, Aboveground Storage Tank; CAS 15-04-01, Septic Tank; CAS 15-05-01, Leachfield; CAS 15-08-01, Liquid Manure Tank; CAS 15-23-01, Underground Radioactive Material Area; CAS 15-23-03, Contaminated Sump, Piping; and CAS 06-07-01 is located at the Decontamination Facility in Area 6, adjacent to Yucca Lake. The remaining CASs are located at the former U.S. Environmental Protection Agency (EPA) Farm in Area 15. The purpose of this CR is to provide a summary of the completed closure activities, to document waste disposal, and to present analytical data confirming that the remediation goals were met. The closure alternatives consisted of closure in place for two of the CASs, and no further action with implementation of best management practices (BMPs) for the remaining five CASs.

  2. 200-BP-5 operable unit treatability test report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-04-01

    The 200-BP-5 Operable Unit was established in response to recommendations presented in the 200 East Groundwater Aggregate Area Management Study Report (AAMSR) (DOE-RL 1993a). Recognizing different approaches to remediation, the groundwater AAMSR recommended separating groundwater from source and vadose zone operable units and subdividing 200 East Area groundwater into two operable units. The division between the 200-BP-5 and 200-PO-1 Operable Units was based principally on source operable unit boundaries and distribution of groundwater plumes derived from either B Plant or Plutonium/Uranium Extraction (PUREX) Plant liquid waste disposal sites.

  3. Custom Unit Pump Design and Testing for the EVA PLSS

    Science.gov (United States)

    Schuller, Michael; Kurwitz, Cable; Goldman, Jeff; Morris, Kim; Trevino, Luis

    2009-01-01

    This paper describes the effort by the Texas Engineering Experiment Station (TEES) and Honeywell for NASA to design and test a pre-flight prototype pump for use in the Extra-vehicular activity (EVA) portable life support subsystem (PLSS). Major design decisions were driven by the need to reduce the pump s mass, power, and volume compared to the existing PLSS pump. In addition, the pump must accommodate a much wider range of abnormal conditions than the existing pump, including vapor/gas bubbles and increased pressure drop when employed to cool two suits simultaneously. A positive displacement, external gear type pump was selected because it offers the most compact and highest efficiency solution over the required range of flow rates and pressure drops. An additional benefit of selecting a gear pump design is that it is self priming and capable of ingesting non-condensable gas without becoming air locked. The chosen pump design consists of a 28 V DC, brushless, sealless, permanent magnet motor driven, external gear pump that utilizes a Honeywell development that eliminates the need for magnetic coupling. Although the planned flight unit will use a sensorless motor with custom designed controller, the pre-flight prototype to be provided for this project incorporates Hall effect sensors, allowing an interface with a readily available commercial motor controller. This design approach reduced the cost of this project and gives NASA more flexibility in future PLSS laboratory testing. The pump design was based on existing Honeywell designs, but incorporated features specifically for the PLSS application, including all of the key features of the flight pump. Testing at TEES verified that the pump meets the design requirements for range of flow rates, pressure drop, power consumption, working fluid temperature, operating time, gas ingestion , and restart capability under both ambient and vacuum conditions. The pump operated between 40 and 240 lbm/hr flowrate, 35 to 100 F

  4. Research on structural design and test technologies for a three-chamber launching device.

    Science.gov (United States)

    Jun, Wu; Qiushi, Yan; Ling, Xiao; Tieshuan, Zhuang; Chengyu, Yang

    2016-07-01

    A three-chamber launching device with improved acceleration is proposed and developed. As indicated by the damage generated during the pill and engineering protection tests, the proposed device is applicable as a high-speed launching platform for pills of different shapes and quality levels. Specifically, it can be used to investigate kinetic energy weapons and their highly destructive effects due to the resulting large bomb fragments. In the horizontal direction of the barrel, two auxiliary chambers are set at a certain distance from the main chamber. When the pill reaches the mouth of the auxiliary chambers, the charges in the auxiliary chambers are ignited by the high-temperature, high-pressure combustible gas trailing the pill. The combustible gas in the auxiliary chambers can resist the rear pressure of the pill and thus maintain the high pressure of the pill base. In this way, the required secondary acceleration of the pill is met. The proposed device features the advantage of launching a pill with high initial velocity under low bore pressure. Key techniques are proposed in the design of the device to address the problems related to the angle between the main chamber axis and the ancillary chamber axis, the overall design of a three-chamber barrel, the structural design of auxiliary propellant charge, the high-pressure combustible gas sealing technology, and the sabot and belt design. Results from the launching test verify the reasonable design of this device and its reliable structural sealing. Additionally, the stiffness and the strength of the barrel meet design requirements. Compared with the single-chamber launching device with the same caliber, the proposed device increases the average launching velocity by approximately 15% and the amount of muzzle kinetic energy by approximately 35%. Therefore, this equipment is capable of carrying out small-caliber, high-speed pill firing tests.

  5. Research on structural design and test technologies for a three-chamber launching device

    Science.gov (United States)

    Jun, Wu; Qiushi, Yan; Ling, Xiao; Tieshuan, Zhuang; Chengyu, Yang

    2016-07-01

    A three-chamber launching device with improved acceleration is proposed and developed. As indicated by the damage generated during the pill and engineering protection tests, the proposed device is applicable as a high-speed launching platform for pills of different shapes and quality levels. Specifically, it can be used to investigate kinetic energy weapons and their highly destructive effects due to the resulting large bomb fragments. In the horizontal direction of the barrel, two auxiliary chambers are set at a certain distance from the main chamber. When the pill reaches the mouth of the auxiliary chambers, the charges in the auxiliary chambers are ignited by the high-temperature, high-pressure combustible gas trailing the pill. The combustible gas in the auxiliary chambers can resist the rear pressure of the pill and thus maintain the high pressure of the pill base. In this way, the required secondary acceleration of the pill is met. The proposed device features the advantage of launching a pill with high initial velocity under low bore pressure. Key techniques are proposed in the design of the device to address the problems related to the angle between the main chamber axis and the ancillary chamber axis, the overall design of a three-chamber barrel, the structural design of auxiliary propellant charge, the high-pressure combustible gas sealing technology, and the sabot and belt design. Results from the launching test verify the reasonable design of this device and its reliable structural sealing. Additionally, the stiffness and the strength of the barrel meet design requirements. Compared with the single-chamber launching device with the same caliber, the proposed device increases the average launching velocity by approximately 15% and the amount of muzzle kinetic energy by approximately 35%. Therefore, this equipment is capable of carrying out small-caliber, high-speed pill firing tests.

  6. A novel and compact nanoindentation device for in situ nanoindentation tests inside the scanning electron microscope

    Directory of Open Access Journals (Sweden)

    Hu Huang

    2012-03-01

    Full Text Available In situ nanomechanical tests provide a unique insight into mechanical behaviors of materials, such as fracture onset and crack propagation, shear band formation and so on. This paper presents a novel in situ nanoindentation device with dimensions of 103mm×74mm×60mm. Integrating the stepper motor, the piezoelectric actuator and the flexure hinge, the device can realize coarse adjustment of the specimen and precision loading and unloading of the indenter automatically. A novel indenter holder was designed to guarantee that the indenter penetrates into and withdraws from the specimen surface vertically. Closed-loop control of the indentation process was established to solve the problem of nonlinearity of the piezoelectric actuator and to enrich the loading modes. The in situ indentation test of Indium Phosphide (InP inside the scanning electron microscope (SEM was carried out and the experimental result indicates the feasibility of the developed device.

  7. Approach of Separately Applying Unit Testing to AspectJ Program

    Institute of Scientific and Technical Information of China (English)

    GU Hai-bo; LU Yan-sheng

    2008-01-01

    A unit testing approach for AspectJ programs is proposed to separately test aspect units which have their own states. In the approach, aspects under test are converted to classes before execution of unit testing. In the conversion process, the context information passed through pointcut is transformed into advices, then the advices are converted to class member methods, and conflicts in the conversion result, if any, are resolved finally. The unit testing process consists of generating test cases, executing test cases and checking results.

  8. Power-aware testing and test strategies for low power devices

    CERN Document Server

    Girard, Patrick; Wen, Xiaoqing

    2010-01-01

    Power-aware testing methods for conventional circuits and systems are explored in this volume, while providing safe testing techniques without compromising reliability. State-of-the-art industrial practices are discusses, as well as EDA solutions.

  9. Device Design and Test of Fatigue Behaviour of Expansion Anchor Subjected to Tensile Loads

    Directory of Open Access Journals (Sweden)

    Zhang Jinfeng

    2016-01-01

    Full Text Available In order to study on the fatigue behaviour of expansion anchor (M16, grade 8.8 for overhead contact system in electrification railways, a set of safe, practical loading device is designed and a fatigue test campaign was carried out at structural laboratory of China Academy of Building Research on expansion anchor embedded in concrete block. The mobile frame of the loading device was designed well by finite-element simulation. According to some fatigue performance test of expansion anchor with different size and form, the device have been assessed experimentally its dependability. The results were found that no fatigue damage phenomenon occurred in all specimens after 2×106 cycles tensile fatigue test in this specific series. It shows that in the condition of medium level or slightly lower maximum stress limit and nominal stress range, expansion bolt has good fatigue resistance. The biggest relative displacement and the residual relative displacement after test (Δδ = δ2-δ1 was also strongly lower than the symbol of the fatigue test failure index of this specific series (0.5mm in the high cycle fatigue regime. The ultimate tension failures mode after fatigue tests in all tested samples take place in the concrete anchorage zone. The reduction range of the ultimate tensile strength properties of the anchorage system was not obvious, and the concrete was seen to be the weakest link of the system.

  10. Development and testing of new upper-limb prosthetic devices: Research designs for usability testing

    OpenAIRE

    Linda Resnik, PT, PhD, OCS

    2011-01-01

    The purposes of this article are to describe usability testing and introduce designs and methods of usability testing research as it relates to upper-limb prosthetics. This article defines usability, describes usability research, discusses research approaches to and designs for usability testing, and highlights a variety of methodological considerations, including sampling, sample size requirements, and usability metrics. Usability testing is compared with other types of study designs used in...

  11. Development and testing of new upper-limb prosthetic devices: Research designs for usability testing

    Directory of Open Access Journals (Sweden)

    Linda Resnik, PT, PhD, OCS

    2011-07-01

    Full Text Available The purposes of this article are to describe usability testing and introduce designs and methods of usability testing research as it relates to upper-limb prosthetics. This article defines usability, describes usability research, discusses research approaches to and designs for usability testing, and highlights a variety of methodological considerations, including sampling, sample size requirements, and usability metrics. Usability testing is compared with other types of study designs used in prosthetic research.

  12. Manufacturing and testing flexible microfluidic devices with optical and electrical detection mechanisms

    NARCIS (Netherlands)

    Ivan, M.G.; Vivet, F.; Meinders, E.R.

    2010-01-01

    Flexible microfluidic devices made of poly(dimethylsiloxane) (PDMS) were manufactured by soft lithography, and tested in detection of ionic species using optical absorption spectroscopy and electrical measurements. PDMS was chosen due to its flexibility and ease of surface modification by exposure

  13. Development and Testing of an Integrated Sandia Cooler Thermoelectric Device (SCTD).

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Terry A.; Staats, Wayne Lawrence,; Leick, Michael Thomas; Zimmerman, Mark D.; Radermacher, Reinhard; Martin, Cara; Nasuta, Dennis; Kalinowski, Paul; Hoffman, William

    2014-12-01

    This report describes a FY14 effort to develop an integrated Sandia Cooler T hermoelectric D evice (SCTD) . The project included a review of feasible thermoelectric (TE) cooling applications, baseline performance testing of an existing TE device, analysis and design development of an integrated SCTD assembly, and performance measurement and validation of the integrated SCTD prototype.

  14. Podcasts on Mobile Devices as a Read-Aloud Testing Accommodation in Middle School Science Assessment

    Science.gov (United States)

    McMahon, Don; Wright, Rachel; Cihak, David F.; Moore, Tara C.; Lamb, Richard

    2016-01-01

    The purpose of this study was to examine the effect of a digitized podcast to deliver read-aloud testing accommodations on mobile devices to students with disabilities and reading difficulties. The total sample for this study included 47 middle school students with reading difficulties. Of the 47 students, 16 were identified as students with…

  15. A Pull-in Based Test Mechanism for Device Diagnostic and Process Characterization

    NARCIS (Netherlands)

    Rocha, L.A.; Mol, L.; Cretu, E.; Wolffenbuttel, R.F.; Machado da Silva, J.

    2008-01-01

    A test technique for capacitive MEMS accelerometers and electrostatic microactuators, based on the measurement of pull-in voltages and resonance frequency, is described. Using this combination of measurements, one can estimate process-induced variations in the device layout dimensions as well as dev

  16. 16 CFR Figure 8 to Part 1512 - Reflectorized Bicycle Wheel Rim Abrasion Test Device

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Reflectorized Bicycle Wheel Rim Abrasion... HAZARDOUS SUBSTANCES ACT REGULATIONS REQUIREMENTS FOR BICYCLES Pt. 1512, Fig. 8 Figure 8 to Part 1512—Reflectorized Bicycle Wheel Rim Abrasion Test Device EC03OC91.074...

  17. A Pull-in Based Test Mechanism for Device Diagnostic and Process Characterization

    NARCIS (Netherlands)

    Rocha, L.A.; Mol, L.; Cretu, E.; Wolffenbuttel, R.F.; Machado da Silva, J.

    2008-01-01

    A test technique for capacitive MEMS accelerometers and electrostatic microactuators, based on the measurement of pull-in voltages and resonance frequency, is described. Using this combination of measurements, one can estimate process-induced variations in the device layout dimensions as well as

  18. Endovascular Device Testing with Particle Image Velocimetry Enhances Undergraduate Biomedical Engineering Education

    Science.gov (United States)

    Nair, Priya; Ankeny, Casey J.; Ryan, Justin; Okcay, Murat; Frakes, David H.

    2016-01-01

    We investigated the use of a new system, HemoFlow™, which utilizes state of the art technologies such as particle image velocimetry to test endovascular devices as part of an undergraduate biomedical engineering curriculum. Students deployed an endovascular stent into an anatomical model of a cerebral aneurysm and measured intra-aneurysmal flow…

  19. [Study on cytotoxicity tests of medical devices based on IC50].

    Science.gov (United States)

    Liu, Chenghu; Wu, Shifu; Hou, Li; Wang, Xin; Wang, Luanluan; Shi, Yanping

    2014-11-01

    To discuss IC50 application in cytotoxicity tests of medical devices, we firstly investigated the vibrating condition and endpoint of MTT method specified in ISO 10993-5: 2009. Furthermore, we demonstrated the application of IC50 in the result evaluation of MTT method. The experimental results show that usage of IC50 in quantitative evaluation of MTT method is feasible.

  20. A simple device to inject indicator gas for wash-out tests during mechanical ventilation

    NARCIS (Netherlands)

    I. Gultuna; P.E.M. Huygen; C. Jabaaij (C.); W.P. Holland (Wim); C. Ince (Can); H.A. Bruining (Hajo)

    1992-01-01

    textabstractObjective: To evaluate a simple device which injects a constant fraction of indicator gas to the inspiratory mixture for performing multi-breath wash-out tests during controlled ventilation. Design: the technique in which the indicator gas is injected at the mouth of the patient (post-mi

  1. Manufacturing and testing flexible microfluidic devices with optical and electrical detection mechanisms

    NARCIS (Netherlands)

    Ivan, M.G.; Vivet, F.; Meinders, E.R.

    2010-01-01

    Flexible microfluidic devices made of poly(dimethylsiloxane) (PDMS) were manufactured by soft lithography, and tested in detection of ionic species using optical absorption spectroscopy and electrical measurements. PDMS was chosen due to its flexibility and ease of surface modification by exposure t

  2. Field test of a novel detection device for Mycobacterium tuberculosis antigen in cough

    Directory of Open Access Journals (Sweden)

    Tesfaye Ato

    2010-06-01

    Full Text Available Abstract Background Tuberculosis is a highly infectious disease that is spread from person to person by infected aerosols emitted by patients with respiratory forms of the disease. We describe a novel device that utilizes immunosensor and bio-optical technology to detect M. tuberculosis antigen (Ag85B in cough and demonstrate its use under field conditions during a pilot study in an area of high TB incidence. Methods The TB Breathalyzer device (Rapid Biosensor Systems Ltd was field tested in the outpatient clinic of Adama Hospital, Ethiopia. Adults seeking diagnosis for respiratory complaints were tested. Following nebulization with 0.9% saline patients were asked to cough into a disposable collection device where cough aerosols were deposited. Devices were then inserted into a portable instrument to assess whether antigen was present in the sample. Demographic and clinical data were recorded and all patients were subjected to chest radiogram and examination of sputum by Ziehl-Nielsen microscopy. In the absence of culture treatment decisions were based on smear microscopy, chest x-ray and clinical assessment. Breathalyzer testing was undertaken by a separate physician to triage and diagnostic assessment. Results Sixty individuals were each subjected to a breathalyzer test. The procedure was well tolerated and for each patient the testing was completed in less than 10 min. Positive breath test results were recorded for 29 (48% patients. Of 31 patients with a diagnosis of tuberculosis 23 (74%; 95% CI 55-87 were found positive for antigen in their breath and 20 (64%; 95% CI 45-80 were smear positive for acid fast bacilli in their sputum. Six patients provided apparent false positive breathalyzer results that did not correlate with a diagnosis of tuberculosis. Conclusions We propose that the breathalyzer device described warrants further investigation as a tool for studying exhalation of M. tuberculosis. The portability, simplicity of use and speed

  3. Calibration of an automated California mastitis test with focus on the device-dependent variation

    OpenAIRE

    Neitzel, Anne-Christin; Stamer, Eckhard; Junge, Wolfgang; Thaller, Georg

    2014-01-01

    The aim of the paper was to estimate the accuracy of the metrology of an installed indirect on-line sensor system based on the automated California Mastitis Test (CMT) with focus on the prior established device-dependent variation. A sensor calibration was implemented. Therefore, seven sensors were tested with similar trials on the dairy research farm Karkendamm (Germany) on two days in July 2011 and January 2012. Thereby, 18 mixed milk samples from serial dilutions were fourfold recorded at ...

  4. Integrated data acquisition system for medical device testing and physiology research in compliance with good laboratory practices.

    Science.gov (United States)

    Koenig, Steven C; Woolard, Cary; Drew, Guy; Unger, Lauren; Gillars, Kevin; Ewert, Dan; Gray, Laman; Pantalos, George

    2004-01-01

    In seeking approval from the US Food and Drug Administration (FDA) for clinical trial evaluation of an experimental medical device, a sponsor is required to submit experimental findings and support documentation to demonstrate device safety and efficacy that are in compliance with Good Laboratory Practices (GLP). The objective of this project was to develop an integrated data acquisition (DAQ) system and documentation strategy for monitoring and recording physiological data when testing medical devices in accordance with GLP guidelines mandated by the FDA. Data aquisition systems were developed as stand-alone instrumentation racks containing transducer amplifiers and signal processors, analog-to-digital converters for data storage, visual display and graphical user-interfaces, power conditioners, and test measurement devices. Engineering standard operating procedures (SOP) were developed to provide a written step-by-step process for calibrating, validating, and certifying each individual instrumentation unit and the integrated DAQ system. Engineering staff received GLP and SOP training and then completed the calibration, validation, and certification process for the individual instrumentation components and integrated DAQ system. Eight integrated DAQ systems have been successfully developed that were inspected by regulatory affairs consultants and determined to meet GLP guidelines. Two of these DAQ systems were used to support 40 of the pre-clinical animal studies evaluating the AbiCor artificial heart (ABIOMED, Danvers, MA). Based in part on these pre-clinical animal data, the AbioCor clinical trials began in July 2001. The process of developing integrated DAQ systems, SOP, and the validation and certification methods used to ensure GLP compliance are presented in this article.

  5. TO EVALUATION TEST OF QUALITY OF MAGNETIC FLUIDS FOR MAGNETOFLUID DEVICES

    Directory of Open Access Journals (Sweden)

    V. G. Bashtovoi

    2016-01-01

    Full Text Available Magnetic fluid is a colloid of magnetic nanoparticles. Using of magnetic fluids in technical devices demands applying of strong non-uniform magnetic fields for a long time. One of the most widespread magnetic fluid devices are magnetic fluid seals of mobile shafts, magnetic fluid supports, bearings, acceleration and angle of inclination gauges, devices for information input in the computer and etc. These devices demand high quality of used fluids. Processes of magnetophoresis and Brownian diffusion in magnetic fluid lead to concentration of magnetic particles in the areas with higher intensity of magnetic field and increase of fluid magnetization in these areas. A local change of particles concentration in the fluid leads to variation of its physical properties. Formation of aggregates from the particles and the further stratification of magnetic fluid, up to its destruction, may be the most serious consequence of redistribution of concentration of magnetic particles. These factors lead to variation of parameters of magnetic fluid devices; cause disturbance of their normal operation and even failure. Therefore, the consistent, high quality magnetic fluids which are not subject to fast stratification in a non-uniform magnetic field are necessary for effective work of the devices. The procedure of evaluation test of quality of magnetic fluids is proposed in this paper. The test is based on studying of influence of processes of magnetophoresis and Brownian diffusion of magnetic particles in magnetic fluid on the forces acting on the volume of fluid in an external non-uniform magnetic field. The procedure is developed on the basis of analysis of magnetic force variation in time under the action of non-uniform field of permanent magnets. Methods of determination of stability of magnetic fluid, known at present, demand rather complicated equipment and laborious and complex investigations. Proposed procedure can be used as an express method for

  6. Comparison Between THOR Anthropomorphic Test Device and THOR Finite Element Model

    Science.gov (United States)

    Moore, Erik

    2014-01-01

    Extended time spent in reduced gravity can cause physiologic deconditioning of astronauts, reducing their ability to sustain excessive forces during dynamic phases of spaceflight such as landing. To make certain that the crew is safe during these phases, NASA must take caution when determining what types of landings are acceptable based on the accelerations applied to the astronaut. In order to test acceptable landings, various trials have been run accelerating humans, cadavers, and Anthropomorphic Test Devices (ATDs), or crash test dummies, at different acceleration and velocity rates on a sled testing platform. Using these tests, risks of injury will be created and metrics will be developed for the likelihood of injuries due to the acceleration. A finite element model (FEM) of the Test Device for Human Occupant Restraint (THOR) ATD has been developed that can simulate these test trials and others (Putnam, 2014), reducing the need for human and ATD testing. Additionally, this will give researchers a more effective way to test the accelerations and orientations encountered during spaceflight landings during design of new space vehicles for crewed missions. However, the FEM has not been proven and must be validated by comparing the forces, accelerations, and other measurements of all parts of the body between the physical tests already completed and computer simulated trials. The purpose of my research was to validate the FEM for the ATD using previously run trials with the physical THOR ATD.

  7. Analytical evaluation of four on-site oral fluid drug testing devices.

    Science.gov (United States)

    Vanstechelman, Sylvie; Isalberti, Cristina; Van der Linden, Trudy; Pil, Kristof; Legrand, Sara-Ann; Verstraete, Alain G

    2012-03-01

    The use of oral fluid (OF) as an alternative matrix for the detection of drugs of abuse has increased over the last decade, leading to the need for a rapid, simple, and reliable on-site OF testing device. Four on-site OF drug testing devices (Dräger DrugTest 5000, Cozart DDS, Mavand Rapid STAT, and Innovacon OrAlert) were evaluated on 408 volunteers at drug treatment centers. UPLC-MS-MS results were used as reference to determine sensitivity, specificity and accuracy for each device, applying Belgian legal confirmation cutoffs for benzoylecgonine, cocaine, and THC (10 ng/mL); morphine and 6-acetylmorphine (5 ng/mL); and amphetamine and 3,4-methylenedioxymethylamphetamine (25 ng/mL). Sensitivity for cocaine was 50%, 50%, 27%, and 11% for DrugTest, OrAlert, Rapid STAT, and DDS 806, respectively. For opiates, sensitivities were 84%, 73%, 77%, and 65%, respectively. For THC, the sensitivities were 81%, 23%, 43%, and 28%, respectively. For amphetamines, the sensitivities were 75%, 33%, 17%, and 67%, respectively. Specificity was >88% for opiates and THC, > 90% for amphetamines, and > 97% for cocaine. All tests showed good specificity. DrugTest had the highest sensitivity, although it was still low for some analytes.

  8. TBI Assessment of Readiness Using a Gait Evaluation Test (TARGET): Development of a Portable mTBI Screening Device

    Science.gov (United States)

    2016-05-01

    Evaluation Test (TARGET): Development of a Portable mTBI Screening Device 5a. CONTRACT NUMBER 5b. GRANT NUMBER W81XWH-15-1-0094 5c. PROGRAM ...determine the validity and reliability of an Android device-based mTBI (mild traumatic brain injury) screening test app for assessing motor function. The...deployment. This study seeks to determine the validity and reliability of an Android device-based mTBI (mild traumatic brain injury) screening test app

  9. 14 CFR 33.96 - Engine tests in auxiliary power unit (APU) mode.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Engine tests in auxiliary power unit (APU... Engine tests in auxiliary power unit (APU) mode. If the engine is designed with a propeller brake which... in operation, and remain stopped during operation of the engine as an auxiliary power unit (“APU...

  10. Design, Fabrication and Test of an Integrated Built-In-Test (BIT) Control Unit.

    Science.gov (United States)

    1982-10-01

    II 00 00 Im 0. N 0x tot ui 0 J~f C * 0 a I CL c. .4 cL’ U)J 00 in8 Three cables provide the interface between the B17 control unit and the power...5. Replace module and test again. Line 6. Blank STO ,I S On A-8 I Sample pin P36 wit nounce:ctr. Lin 4.A Blankv Ye No Most NegativeYe L n 3 Fault in

  11. Intelligent Information Retrieval: Part IV. Testing the Timing of Two Information Retrieval Devices in a Naturalistic Setting.

    Science.gov (United States)

    Cole, Charles

    2001-01-01

    Reports the results of two studies of undergraduates that tested an uncertainty expansion information retrieval device and an uncertainty reduction device in naturalistic settings, designed to be given at different stages of Kuhlthau's information search process. Concludes that the timing of the device interventions is crucial to their potential…

  12. 30 CFR 75.1103-8 - Automatic fire sensor and warning device systems; examination and test requirements.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Automatic fire sensor and warning device...-UNDERGROUND COAL MINES Fire Protection § 75.1103-8 Automatic fire sensor and warning device systems; examination and test requirements. (a) Automatic fire sensor and warning device systems shall be examined at...

  13. [Nosocomial infections associated to invasive devices in the intensive care units of a national hospital of Lima, Peru].

    Science.gov (United States)

    Chincha, Omayra; Cornelio, Elia; Valverde, Violeta; Acevedo, Mónica

    2013-01-01

    In order to describe the incidence of nosocomial infections associated to invasive devices in intensive care units (UCI) of the National Hospital Cayetano Heredia, a retrospective observational study was conducted using the data from the Office of Epidemiology and Environmental Health from 2010 to 2012. A total number of 222 nosocomial infections were reported; the general medicine UCI reported the highest incidence of pneumonia cases associated to a mechanical ventilator in 1000 days of use of the device (28.6); infection of the blood stream associated to central venous catheter (11.9), and infection of the urinary tract associated to a catheter (8,1). The main infectious agents isolated were Pseudomona sp. (32.3%) in the emergency UCI, negative Staphylococcus coagulasa (36%) in the general medicine UCI and Candida sp (69.2%) in the Surgery UCI. The rates of infections associated to invasive devices were high as in other national hospitals with limited resources and infrastructure.

  14. A test device for isotopic γ-ray imaging with CdZnTe detector

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A test device for isotopic γ-ray imaging, which consists of an isotope γ-ray source, a CdZnTe γ-ray spectrometer and other auxiliary equipment, is studied here. Compared with the conventional X-ray, the isotope γ-ray,which is utilized in this project, has its own advantages in imaging. Furthermore, with a room-temperature high-energy-resolution CdZnTe detector and a modern imaging processing technique, this device is capable of effectively suppressing the background and gaining more information, thus it can obtain a better image than conventional X-ray devices. In the experiment of PCB imaging, all soldered points and chip components are sharply demonstrated.

  15. Assessment And Testing of Industrial Devices Robustness Against Cyber Security Attacks

    CERN Document Server

    Tilaro, F

    2011-01-01

    CERN (European Organization for Nuclear Research),like any organization, needs to achieve the conflicting objectives of connecting its operational network to Internet while at the same time keeping its industrial control systems secure from external and internal cyber attacks. With this in mind, the ISA-99[0F1] international cyber security standard has been adopted at CERN as a reference model to define a set of guidelines and security robustness criteria applicable to any network device. Devices robustness represents a key link in the defense-in-depth concept as some attacks will inevitably penetrate security boundaries and thus require further protection measures. When assessing the cyber security robustness of devices we have singled out control system-relevant attack patterns derived from the well-known CAPEC[1F2] classification. Once a vulnerability is identified, it needs to be documented, prioritized and reproduced at will in a dedicated test environment for debugging purposes. CERN - in collaboration ...

  16. Influence of heavy ion flux on single event effect testing in memory devices

    Science.gov (United States)

    Luo, Jie; Liu, Jie; Sun, Youmei; Hou, Mingdong; Xi, Kai; Liu, Tianqi; Wang, Bin; Ye, Bing

    2017-09-01

    The natural space presents a particle flux variable environment and choosing a suitable flux value for ground-based single event experiments is an unresolved problem so far. In this work, various types of memory devices have been tested over the ion flux range from 10 to 105 ions/(cm2·s) using different ions covering LET from 10.1 to 99.8 MeV·cm2/mg. It was found that for most devices the error rates of single event upsets are affected by the applied flux value. And the effect involving flux becomes prominent as it is increased above 103 ions/(cm2·s). Different devices behave differently as the flux is increased and the flux effect depends strongly on the LET of the impinging ions. The results concluded in this experiment are discussed in detail and recommendations for choosing appropriate experimental flux are given.

  17. Preliminary test results from the CELSS Test Facility Engineering Development Unit

    Science.gov (United States)

    Kliss, Mark H.; Macelroy, R. D.; Blackwell, C. C.; Borchers, B. A.; Drews, M. E.; Longabaugh, J. R.; Yendler, B. S.; Zografos, A. I.

    1994-01-01

    As part of the NASA Controlled Ecological Life Support System (CELSS) Program, a CELSS Test Facility (CTF) is being planned for installation on the Space Station. The CTF will be used to provide data on the productivity and efficiency of a variety of CELSS higher plant crops grown in the microgravity environment of the Space Station. Tight environmental control will be maintained while data on gas exchange rates and biomass accumulation rates are collected. In order to obtain an early realistic determination of the subsystem and system requirements necessary to provide the environmental conditions specified for CTF crop productivity experiments, an Engineering Development Unit (EDU) has been designed, constructed and is in the process of subsystem and system testing at NASA Ames Research Center. The EDU is a ground test-bed which will be used to characterize the integrated performance of major subsystem technologies, to evaluate hardware candidates and control strategies required for the CTF, and to further define the ability to meet CTF requirements within present Space Station constraints. This paper reviews the functional requirements for the EDU, and focuses on the performance evaluation and test results of the various subsystems. Preliminary integrated performance results and control system operation are addressed, and plans for future science and technology testing are discussed.

  18. JTst - An Automated Unit Testing Tool for Java Program

    OpenAIRE

    Kamal Z.  Zamli; Nor A.M.   Isa

    2008-01-01

    Software testing is an integral part of software development lifecycle. Lack of testing can often lead to disastrous consequences including lost of data, fortunes, and even lives. Despite its importance, current software testing practice lacks automation, and is still primarily based on highly manual processes from the generation of test cases up to the actual execution of the test. Although the emergence of helpful automated testing tools in the market is blooming, their adoptions are lackin...

  19. Fabrication and test of digital output interface devices for gas turbine electronic controls

    Science.gov (United States)

    Newirth, D. M.; Koenig, E. W.

    1978-01-01

    A program was conducted to develop an innovative digital output interface device, a digital effector with optical feedback of the fuel metering valve position, for future electronic controls for gas turbine engines. A digital effector (on-off solenoids driven directly by on-off signals from a digital electronic controller) with optical position feedback was fabricated, coupled with the fuel metering valve, and tested under simulated engine operating conditions. The testing indicated that a digital effector with optical position feedback is a suitable candidate, with proper development for future digital electronic gas turbine controls. The testing also identified several problem areas which would have to be overcome in a final production configuration.

  20. A novel nanoscratch device compatible with commercial microscope for in situ tests of materials’ mechanics

    Directory of Open Access Journals (Sweden)

    Ning Li

    2016-04-01

    Full Text Available For exploring the mechanical properties and behaviors of new materials, a novel in situ nanoscratch device compatible with commercial microscope has been developed. The developed device with specific dimensions of 178 mm × 165 mm × 78 mm includes the coarse positioning module, the precise feed module, the measurement module, and the control module. Integrating the servo motor, worm and gears, ball screw, flexure hinge, and piezoelectric actuator, the device can realize macroscopical coarse positioning motion and precise feed motion. A novel arrangement of load sensor and indenter with no middle chain is used to reduce the measurement error. Closed-loop control system is established to guarantee the accuracy of load and displacement control. Mechanical properties of the developed device have been proved by calibrating the load sensor, finite element analysis of flexure hinge, and verifying the output performance. The in situ nanoscratch test has been conducted on the single crystal copper. The captured images and finite element analysis prove the feasibility and accuracy of the developed device.

  1. Testing devices for the prevention and treatment of stroke and its complications.

    Science.gov (United States)

    Bath, Philip M; Brainin, Michael; Brown, Chloe; Campbell, Bruce; Davis, Stephen M; Donnan, Geoffrey A; Ford, Gary A; Hacke, Werner; Iglesias, Cynthia; Lees, Kennedy R; Pugh, Stacey S; Saver, Jeff L; Schellinger, Peter D; Truelsen, Thomas

    2014-08-01

    We are entering a challenging but exciting period when many new interventions may appear for stroke based on the use of devices. Hopefully these will lead to improved outcomes at a cost that can be afforded in most parts of the world. Nevertheless, it is vital that lessons are learnt from failures in the development of pharmacological interventions (and from some early device studies), including inadequate preclinical testing, suboptimal trial design and analysis, and underpowered studies. The device industry is far more disparate than that seen for pharmaceuticals; companies are very variable in size and experience in stroke, and are developing interventions across a wide range of stroke treatment and prevention. It is vital that companies work together where sales and marketing are not involved, including in understanding basic stroke mechanisms, prospective systematic reviews, and education of physicians. Where possible, industry and academics should also work closely together to ensure trials are designed to be relevant to patient care and outcomes. Additionally, regulation of the device industry lags behind that for pharmaceuticals, and it is critical that new interventions are shown to be safe and effective rather than just feasible. Phase IV postmarketing surveillance studies will also be needed to ensure that devices are safe when used in the 'real-world' and to pick up uncommon adverse events.

  2. Model-based testing with UML applied to a roaming algorithm for Bluetooth devices

    Institute of Scientific and Technical Information of China (English)

    DAI Zhen Ru; GRABOWSKI Jens; NEUKIRCHEN Helmut; PALS Holger

    2004-01-01

    In late 2001,the Object Management Group issued a Request for Proposal to develop a testing profile for UML2.0. In June 2003,the work on the UML 2.0 Testing Profile was finally adopted by the OMG. Since March 2004,it has become an official standard of the OMG. The UML 2.0 Testing Profile provides support for UML based model-driven testing. This paper introduces a methodology on how to use the testing profile in order to modify and extend an existing UML design model for test issues. The application of the methodology will be explained by applying it to an existing UML Model for a Bluetooth device.

  3. Model-based testing with UML applied to a roaming algorithm for Bluetooth devices

    Institute of Scientific and Technical Information of China (English)

    DAIZhenRu; GRABOWSKIJens; NEUKIRCHENHelmut; PALSHolger

    2004-01-01

    In late 2001, the Object Management Group issued a Request for Proposal to develop a testing profile for UML 2.0. In June 2003, the work on the UML 2.0 Testing Profile was finally adopted by the OMG. Since March 2004, it has become an official standard of the OMG. The UML 2.0 Testing Profile provides support for UML based model-driven testing. This paper introduces a methodology on how to use the testing profile in order to modify and extend an existing UML design model for test issues. The application of the methodology will be explained by applying it to an existing UML Model for a Bluetooth device.

  4. Model-based testing with UML applied to a roaming algorithm for bluetooth devices.

    Science.gov (United States)

    Dai, Zhen Ru; Grabowski, Jens; Neukirchen, Helmut; Pals, Holger

    2004-11-01

    In late 2001, the Object Management Group issued a Request for Proposal to develop a testing profile for UML 2.0. In June 2003, the work on the UML 2.0 Testing Profile was finally adopted by the OMG. Since March 2004, it has become an official standard of the OMG. The UML 2.0 Testing Profile provides support for UML based model-driven testing. This paper introduces a methodology on how to use the testing profile in order to modify and extend an existing UML design model for test issues. The application of the methodology will be explained by applying it to an existing UML Model for a Bluetooth device.

  5. A regenerative microchannel device for recording multiple single-unit action potentials in awake, ambulatory animals.

    Science.gov (United States)

    Srinivasan, Akhil; Tipton, John; Tahilramani, Mayank; Kharbouch, Adel; Gaupp, Eric; Song, Chao; Venkataraman, Poornima; Falcone, Jessica; Lacour, Stéphanie P; Stanley, Garrett B; English, Arthur W; Bellamkonda, Ravi V

    2016-02-01

    Despite significant advances in robotics, commercially advanced prosthetics provide only a small fraction of the functionality of the amputated limb that they are meant to replace. Peripheral nerve interfacing could provide a rich controlling link between the body and these advanced prosthetics in order to increase their overall utility. Here, we report on the development of a fully integrated regenerative microchannel interface with 30 microelectrodes and signal extraction capabilities enabling evaluation in an awake and ambulatory rat animal model. In vitro functional testing validated the capability of the microelectrodes to record neural signals similar in size and nature to those that occur in vivo. In vitro dorsal root ganglia cultures revealed striking cytocompatibility of the microchannel interface. Finally, in vivo, the microchannel interface was successfully used to record a multitude of single-unit action potentials through 63% of the integrated microelectrodes at the early time point of 3 weeks. This marks a significant advance in microchannel interfacing, demonstrating the capability of microchannels to be used for peripheral nerve interfacing.

  6. Policy and Policy Formulation Considerations for Incorporation of Secure Mobile Devices in USMC Ground Combat Units

    Science.gov (United States)

    2014-09-01

    network usage and health (Office of the Department of Defense Chief Information Officer, 2012). 22 Objective c. Educate and train mobile device users...perform beyond your wildest dreams.” These two concepts are not merely part of a “feel-good” speech during a relaxing yoga session. In design...LIST OF REFERENCES Ahmed, M., & Ahamad, M. (2012). Protecting health information on mobile devices. Proceedings of the Second ACM Conference on

  7. A Prospective, Descriptive Study to Determine the Rate and Characteristics of and Risk Factors for the Development of Medical Device-related Pressure Ulcers in Intensive Care Units.

    Science.gov (United States)

    Hanonu, Seval; Karadag, Ayise

    2016-02-01

    Pressure ulcers do not develop only in areas with bony prominences; they can develop in any tissue under pressure, including pressure exerted by medical devices. A prospective, descriptive study was conducted from December 15, 2013 to March 25, 2014 to determine the prevalence, risk factors, and characteristics of medical device-related hospitalacquired pressure ulcers (MDR HAPUs) among all patients (N = 175) in 5 adult intensive care units (ICUs) in a university hospital in Turkey. The previously established point prevalence of hospital-acquired pressure ulcers (HAPUs) in these ICUs was 15%. Patients were evaluated in the first 24 hours after admission and observed 6 times thereafter in intervals of 48 hours. Demographic (eg, age, gender, body mass index) and medical device-related pressure ulcer data (eg, location, device type, stage), and Braden Scale scores were collected and analyzed; frequencies and percentages were calculated and Mann-Whitney U Test, t-test, and odds ratios were applied. Twenty-seven (27) patients (15.4%) developed nonMDR HAPUs and 70 (40.0%) developed MDR HAPUs. MDR HAPUs occurred most frequently (45.0%) in patients with an endotracheal tube. The most frequent type (42.6%) was Stage II. The highest rates of MDR HAPUs were observed among internal medicine ICU patients (OR 7.041), patients who also had a nonMDR HAPU (OR 6.6), patients in the high Braden risk score group (OR 1.8), or patients who received enteral feeding (OR 2.12). Because of the high rate of MDR HAPUs noted, policies and procedures aimed at preventing medical device-related pressure ulcers are needed.

  8. 76 FR 82323 - Design, Inspection, and Testing Criteria for Air Filtration and Adsorption Units

    Science.gov (United States)

    2011-12-30

    ... COMMISSION Design, Inspection, and Testing Criteria for Air Filtration and Adsorption Units AGENCY: Nuclear...-1274, ``Design, Inspection, and Testing Criteria for Air Filtration and Adsorption Units of....'' This guide applies to the design, inspection, and testing of air filtration and iodine adsorption...

  9. [Preliminary Study on Error Control of Medical Devices Test Reports Based on the Analytic Hierarchy Process].

    Science.gov (United States)

    Huang, Yanhong; Xu, Honglei; Tu, Rong; Zhang, Xu; Huang, Min

    2016-01-01

    In this paper, the common errors in medical devices test reports are classified and analyzed. And then the main 11 influence factors for these inspection report errors are summarized. The hierarchy model was also developed and verified by presentation data using MATLAB. The feasibility of comprehensive weights quantitative comparison has been analyzed by using the analytic hierarchy process. In the end, this paper porspects the further research direction.

  10. Eddy current nondestructive testing device for measuring variable characteristics of a sample utilizing Walsh functions

    Science.gov (United States)

    Libby, Hugo L.; Hildebrand, Bernard P.

    1978-01-01

    An eddy current testing device for measuring variable characteristics of a sample generates a signal which varies with variations in such characteristics. A signal expander samples at least a portion of this generated signal and expands the sampled signal on a selected basis of square waves or Walsh functions to produce a plurality of signal components representative of the sampled signal. A network combines these components to provide a display of at least one of the characteristics of the sample.

  11. Test and device to evaluate the capillary absorption in soil specimens of adobe and rammed earth

    OpenAIRE

    Cirvini, Silvia Augusta; Gomez Voltan, Jose Alejandro

    2016-01-01

    The moisture degree of capillary rise is an indicator of the state of conservation of earthen construction and their mechanical response to load cases, especially seismic action, since the buildings diminish resistant capacity where they are more demanding by the base shear. This paper shows a test procedure and a specific device to evaluate the rate of rise and variation of moisture content in samples of soil for use in new or existing walls of adobe and tapia. These parameters allow evalu...

  12. Podcasts on Mobile Devices as a Read-Aloud Testing Accommodation in Middle School Science Assessment

    Science.gov (United States)

    McMahon, Don; Wright, Rachel; Cihak, David F.; Moore, Tara C.; Lamb, Richard

    2016-04-01

    The purpose of this study was to examine the effect of a digitized podcast to deliver read-aloud testing accommodations on mobile devices to students with disabilities and reading difficulties. The total sample for this study included 47 middle school students with reading difficulties. Of the 47 students, 16 were identified as students with disabilities who received special education services. Participants were randomly assigned to three experimental testing conditions, standard administration, teacher-controlled read-aloud in traditional group delivery format, and student-controlled read-aloud delivered as a podcast and accessed on a mobile device, and given sample end-of-year science assessments. Based on a factorial analysis of variances, with test conditions and student status as the fixed factors, both student groups demonstrated statistically significant gains based on their testing conditions. Results support the use of podcast delivery as a viable alternative to the traditional teacher-delivered read-aloud test accommodation. Conclusions are discussed in the context of universal design for learning testing accommodations for future research and practice.

  13. Fabrication and testing of novel blood separation devices based on microchannel bend structures

    Science.gov (United States)

    Blattert, C.; Jurischka, R.; Schoth, A.; Kerth, P.; Menz, W.

    2005-02-01

    Most clinical chemistry tests are performed on cell-free serum or plasma. Therefore micro assay devices for blood tests require integrated on-chip microfluidics for separation of plasma or serum from blood. Polymers are ideally suited for these applications due to their material properties and their applicability for high volume production. These requirements are achieved by a new on-chip blood separation technique based on microchannel bend structures and a rapid processing technology for micro assay devices using injection molding or hot embossing. Different prototype polymer chips with channel dimensions down to 20 μm and aspect ratios of 4 have been fabricated by injection molding and hot embossing. The inserts for the molding tools were fabricated by an UV-LIGA technology. The separation efficiency of these chips has been tested with human blood samples. The results show different separation efficiencies up to 100 % for blood cells and plasma depending on microchannel geometry as well as cell concentration. As compared to present microfluidic devices for the separation of blood cells like filters, membranes or filtration by diffusion the microchannel bend is an integrated on-chip blood separation method. It combines the advantages of rapid separation times and a simple geometry that leads to cost-effective high volume production using injection molding.

  14. Fault-Tolerant Design and Testing of USB2.0 Peripheral Devices IP Core System

    Institute of Scientific and Technical Information of China (English)

    BAI Xiaoping; WEI Yuanfeng

    2007-01-01

    Universal serial bus 2.0 (USB2.0) is a kind of mainstream interface technology. The traditional USB developing is only to develop USB peripheral devices. For the USB2.0 peripheral devices IP core system that has wide application foreground, some interference inevitably exists in signal transmitting. Some fault-tolerant design and test methods must be adopted in order to correctly transmit and receive data. Combining with a project, this paper introduces in detail about measures, hardware implement, and test methods of fault-tolerant design about USB2.0 peripheral devices IP core system. Fault-tolerant design measures, noise reduction measures of signal processing, fault-tolerant methods about data encode and decode, package identification (ID) field fault-tolerant methods, and cyclic redundancy checks fault-tolerant methods are discussed. The paper also presents some hardware implement methods about fault-tolerant design of data decode and test methods about fault-tolerant design of USB2.0 IP core system. These methods can offer the reference for development of USB2.0 system in all kinds of electronics instrumentations.

  15. Wear of nanofilled dental composites in a newly-developed in vitro testing device

    Science.gov (United States)

    Lawson, Nathaniel C.

    Purpose. In vivo wear of dental composites can lead to loss of individual tooth function and the need to replace a composite restoration. To evaluate the wear performance of new and existing dental composites, we developed a novel system for measuring in vitro wear and we used this system to analyze the mechanisms of wear of nanofilled composite materials. Methods. A modified wear testing device was designed based on the Alabama wear testing machine. The new device consists of: (1) an antagonist which is lowered to and raised from the composite specimen by weight loading, (2) a motorized stage to cause the antagonist to slide 2mm on the composite surface, and (3) pumps for applying lubricant to the specimens. Various testing parameters of the device were examined before testing, including the impulse force, the third-body medium, the lubricant and antagonist. The parameters chosen for this study were 20N at 1Hz with a 33% glycerine lubricant and stainless steel antagonist. Three nano-composites were fabricated with a BisGMA polymer matrix and 40nm SiO2 filler particles at three filler loads (25%, 50% and 65%). The mechanical properties of the composites were measured. The materials were then tested in the modified wear testing device under impact wear, sliding wear and a combination of impact and sliding wear. The worn surfaces were then analyzed with a non-contact profilometer and SEM. Results. The volumetric wear data indicated that increasing filler content beyond 25% decreased the wear resistance of the composites. Increasing filler content increased hardness and decreased toughness. SEM evaluation of the worn specimens indicated that the 25% filled materials failed by fatigue and the 50% and 65% filled materials failed by abrasive wear. Impact wear produced fretting in this device and sliding wear is more aggressive than impact wear. Conclusion. Based on the results of this study and previous studies on this topic, manufacturers are recommended to use a filler

  16. 10 CFR 34.67 - Records of leak testing of sealed sources and devices containing depleted uranium.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Records of leak testing of sealed sources and devices containing depleted uranium. 34.67 Section 34.67 Energy NUCLEAR REGULATORY COMMISSION LICENSES FOR INDUSTRIAL... Requirements § 34.67 Records of leak testing of sealed sources and devices containing depleted uranium....

  17. SERVICE TEST OF CONTROLLER, DIFFERENTIAL PRESSURE, PIPELINE PUMP UNIT

    Science.gov (United States)

    Nineteen test items were operated for a total of 1,182 hours at Fort Lee, Virginia and at Hachinoehe POL Storage Area, Hachinohe, Japan, and were...satisfactory with respect to familiarization and training, maintenance and safety. The test items were suitable with respect to compatibility with...related equipment. The test items were unsatisfactory with respect to operational performance, durability and reliability.

  18. Transfer Relation between the Compression Test Rig and the Anthropomorphic Test Device (ATD) Lower Leg

    Science.gov (United States)

    2015-08-01

    respectively. Moreover, SKYDEX material was used as the nominal floor mat in this loading test. Iso View Front View 11 Table 3 Loading conditions for...Fig. 18 Typical input- and output-acceleration histories in the CTR loading, CTR_03 (Height = 30 inches) 0 1000 2000 3000 -2 0 2 4 6 8 10 12 14 Ac...0.0 2.5 5.0 7.5 0 1000 2000 3000 -2 0 2 4 6 8 10 12 14 Lo ad (k N ) Ac ce le ra tio n (k N ) Time (msec) Input Acceleration Lower Tibia Load 15

  19. Efficient Testing of Wireless Devices from 800 MHz to 18 GHz

    Directory of Open Access Journals (Sweden)

    A. Scannavini

    2009-12-01

    Full Text Available Small antennas and other modern communication applications are using increasingly higher frequencies while demanding shorter development time and very rapid testing cycles. A fast and accurate way to exhaustively determine antenna performance and/or investigate device malfunction is based on spherical near field measurement techniques combined with probe array technology. This paper describes the innovative design aspects of the StarLab portable antenna measurement system and present results from the validation campaigns including both passive and active measurements. The use of integrated diagnostic and analysis software modules for efficient antenna design and testing is also presented.

  20. New nucleic acid testing devices to diagnose infectious diseases in resource-limited settings.

    Science.gov (United States)

    Maffert, P; Reverchon, S; Nasser, W; Rozand, C; Abaibou, H

    2017-06-01

    Point-of-care diagnosis based on nucleic acid testing aims to incorporate all the analytical steps, from sample preparation to nucleic acid amplification and detection, in a single device. This device needs to provide a low-cost, robust, sensitive, specific, and easily readable analysis. Microfluidics has great potential for handling small volumes of fluids on a single platform. Microfluidic technology has recently been applied to paper, which is already used in low-cost lateral flow tests. Nucleic acid extraction from a biological specimen usually requires cell filtration and lysis on specific membranes, while affinity matrices, such as chitosan or polydiacetylene, are well suited to concentrating nucleic acids for subsequent amplification. Access to electricity is often difficult in resource-limited areas, so the amplification step needs to be equipment-free. Consequently, the reaction has to be isothermal to alleviate the need for a thermocycler. LAMP, NASBA, HDA, and RPA are examples of the technologies available. Nucleic acid detection techniques are currently based on fluorescence, colorimetry, or chemiluminescence. For point-of-care diagnostics, the results should be readable with the naked eye. Nowadays, interpretation and communication of results to health professionals could rely on a smartphone, used as a telemedicine device. The major challenge of creating an "all-in-one" diagnostic test involves the design of an optimal solution and a sequence for each analytical step, as well as combining the execution of all these steps on a single device. This review provides an overview of available materials and technologies which seem to be adapted to point-of-care nucleic acid-based diagnosis, in low-resource areas.

  1. Semipermeable-membrane devices as an in situ and laboratory testing chamber

    Energy Technology Data Exchange (ETDEWEB)

    Gardiner, W.W.; Word, J.Q. [Battelle, Seqium, WA (United States). Marine Sciences Lab.

    1995-12-31

    The use of semipermeable-membrane devices (SPMDs) to measure the bioavailability of dissolved (< 10{angstrom}) hydrophobic-organic-compounds has recently been established. These low-density polyethylene bags are effective and relatively easy in situ devices for evaluating bioaccumulation potentials of polyaromatic hydrocarbons, pesticides, polychlorinated biphenyls, and dioxins. The authors believe SPMDs may also be effective in situ and laboratory testing chambers for evaluating dissolved contaminant effects on sensitive life stages of freshwater/marine fish and invertebrates. Applications may include dissolved contaminant toxicity of effluents, porewater, water-column, and surface microlayer. In laboratory tests, the applicability of SPMD-testing chambers was explored with marine bivalve larvae (Mytilus galloprovincialis). Test solutions were filtered seawater, dissolved copper, ammonia, and an elutriate preparation that included both organic and inorganic contaminants. SPMDs were filled with seawater, immersed in test solutions for 24-h, then spiked with fertilized M. galloprovincialis embryos. Following 48-h exposures, >90% survival and normal development was observed in the controls, indicating that incubation in the SPMDs did not adversely affect larval development. Incubation in test treatments resulted in slight, but not significantly different, reductions in normal development, relative to the controls. The authors believe longer SPMD immersion prior to testing will likely be required to allow SPMD contents to reach equilibrium with test solutions before eliciting a significant toxicological response. While this may limit the application of SPMDs for short term in situ exposures, they may be used for field/laboratory exposures of a week or more or for collecting equilibrated field samples for laboratory testing.

  2. Horizontal shaking table tests and analysis on structures with multi-dimensional earthquake isolation and mitigation devices

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    The viscoelastic multi-dimensional earthquake isolation and mitigation device is a new kind of passive control device, which has both earthquake isolation and earthquake mitigation abilities. In order to quantify the horizontal earthquake isolation and mitigation effect of this device on structures, shaking table tests on structures with and without the devices and the corresponding analysis on earthquake isolation and mitigation properties are carried out. It can be shown from the experimental and analytical results that the device has both earthquake isolation and earthquake mitigation effects on structures in horizontal direction, and its horizontal earthquake mitigation coefficients can be referred to those of the rubber bearing earthquake isolation structure.

  3. Lumped Parameter Modeling for Rapid Vibration Response Prototyping and Test Correlation for Electronic Units

    Science.gov (United States)

    Van Dyke, Michael B.

    2013-01-01

    Present preliminary work using lumped parameter models to approximate dynamic response of electronic units to random vibration; Derive a general N-DOF model for application to electronic units; Illustrate parametric influence of model parameters; Implication of coupled dynamics for unit/board design; Demonstrate use of model to infer printed wiring board (PWB) dynamics from external chassis test measurement.

  4. 14 CFR 120.123 - Drug testing outside the territory of the United States.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Drug testing outside the territory of the... OPERATIONS DRUG AND ALCOHOL TESTING PROGRAM Drug Testing Program Requirements § 120.123 Drug testing outside the territory of the United States. (a) No part of the testing process (including specimen collection...

  5. Standard test method for calibration of surface/stress measuring devices

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    1997-01-01

    Return to Contents page 1.1 This test method covers calibration or verification of calibration, or both, of surface-stress measuring devices used to measure stress in annealed and heat-strengthened or tempered glass using polariscopic or refractometry based principles. 1.2 This test method is nondestructive. 1.3 This test method uses transmitted light, and therefore, is applicable to light-transmitting glasses. 1.4 This test method is not applicable to chemically tempered glass. 1.5 Using the procedure described, surface stresses can be measured only on the “tin” side of float glass. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  6. Comparison of the analytical capabilities of the BAC Datamaster and Datamaster DMT forensic breath testing devices.

    Science.gov (United States)

    Glinn, Michele; Adatsi, Felix; Curtis, Perry

    2011-11-01

    The State of Michigan uses the Datamaster as an evidential breath testing device. The newest version, the DMT, will replace current instruments in the field as they are retired from service. The Michigan State Police conducted comparison studies to test the analytical properties of the new instrument and to evaluate its response to conditions commonly cited in court defenses. The effects of mouth alcohol, objects in the mouth, and radiofrequency interference on paired samples from drinking subjects were assessed on the DMT. The effects of sample duration and chemical interferents were assessed on both instruments, using drinking subjects and wet-bath simulators, respectively. Our testing shows that Datamaster and DMT results are essentially identical; the DMT gave accurate readings as compared with measurements made using simulators containing standard ethanol solutions and that the DMT did not give falsely elevated breath alcohol results from any of the influences tested.

  7. Step Stress Testing of Receiver/Transmitter Units. Part 2

    Science.gov (United States)

    1993-02-01

    CondVitio with plotter. STEP-STPESS TEST MSN’ 1030 PLO7 3 OF 3 COMPOLETE ST: 01 i23191 ;0 TEMP. CTEP-STRESS TEST t4SNi c~ 170 _E_1 I L VEL 10 :5-rn nut ...medium caramel brown after Stress- Step testing. The area around 04 through Q6 and Q9, show some darkening also. 3 Deep test probe marks found at...area of contact is made with R4 body. The conformal coating on C4 is darker than other tantalum capacitors and is a light caramel brown in color. 13

  8. Exploring Trends in Intrauterine Device (IUD) Usage among Women in the United States: A Literature Review

    Science.gov (United States)

    Nobiling, Brandye; Drolet, Judy C.

    2012-01-01

    Intrauterine devices (IUDs) have not been popular contraceptives in the US for the past 40 years. Recent evidence, however, has shown a slight rebirth in use, from a rate of approximately 2% in 2002 to over 5% in 2008 (Guttmacher Institute, 2010). Empirical evidence is favorable of IUD use in most women, but the still-low usage rate suggests…

  9. Single cells as experimentation units in lab-on-a-chip devices

    NARCIS (Netherlands)

    le Gac, Severine; van den Berg, Albert

    'Lab-on-a-chip' technology (LOC) has now reached a mature state and is employed commonly in research in the life sciences. LOC devices make novel experimentation possible while providing a sophisticated environment for cellular investigation. As a next step, we introduce here the concept of a

  10. The development of an instrumented wheelchair propulsion testing and training device.

    Science.gov (United States)

    Klaesner, Joseph; Morgan, Kerri A; Gray, David B

    2014-01-01

    Researchers have used several types of testing devices and training surfaces to examine wheelchair propulsion. Testing and training wheelchair users on the actual surface of interest, such as tile floors or ramps, is ideal but difficult. Devices such as treadmills, dynamometers, and ergometers allow for researchers and clinicians to observe wheelchair users in a controlled space. However, these devices often do not have the ability to realistically simulate the environment. This methodological article describes the instrumentation, development and function of a wheelchair dynamometer system, the WheelMill System (WMS), a uniquely adjustable roller system for wheelchairs. Three participants wheeled on the WMS, over a tile surface and up two different graded slopes with the SmartWheel to compare speed and forces. The WMS reasonably simulated propulsion over a tile floor, though the participants' speed was slightly faster on tile, and the peak forces for each propulsion stroke varied more on tile than on the WMS. For the slopes, the speed oscillated over a greater range and was slower, and the measured peak forces were higher than the values measured on the WMS. The WMS may have several applications, though additional studies on a greater and more diverse population are needed.

  11. Mechanism Development, Testing, and Lessons Learned for the Advanced Resistive Exercise Device

    Science.gov (United States)

    Lamoreaux, Christopher D.; Landeck, Mark E.

    2006-01-01

    The Advanced Resistive Exercise Device (ARED) has been developed at NASA Johnson Space Center, for the International Space Station (ISS) program. ARED is a multi-exercise, high-load resistive exercise device, designed for long duration, human space missions. ARED will enable astronauts to effectively maintain their muscle strength and bone mass in the micro-gravity environment more effectively than any other existing devices. ARED's resistance is provided via two, 20.3 cm (8 in) diameter vacuum cylinders, which provide a nearly constant resistance source. ARED also has a means to simulate the inertia that is felt during a 1-G exercise routine via the flywheel subassembly, which is directly tied to the motion of the ARED cylinders. ARED is scheduled to fly on flight ULF 2 to the ISS and will be located in Node 1. Presently, ARED is in the middle of its qualification and acceptance test program. An extensive testing program and engineering evaluation has increased the reliability of ARED by bringing potential design issues to light before flight production. Some of those design issues, resolutions, and design details will be discussed in this paper.

  12. Postmortem circulation: a new model for testing endovascular devices and training clinicians in their use.

    Science.gov (United States)

    Chevallier, Christine; Willaert, Wouter; Kawa, Emilia; Centola, Marcos; Steger, Beat; Dirnhofer, Richard; Mangin, Patrice; Grabherr, Silke

    2014-05-01

    The development of new medical devices, such as aortic valves, requires numerous preliminary studies on animals and training of personnel on cadavers before the devices can be used in patients. Postmortem circulation, a technique used for postmortem angiography, allows the vascular system to be reperfused in a way similar to that in living persons. This technique is used for postmortem investigations to visualize the human vascular system and to make vascular diagnoses. Specific material for reperfusing a human body was developed recently. Our aim was to investigate whether postmortem circulation that imitates in vivo conditions allows for the testing of medical materials on cadavers. We did this by delivering an aortic valve using minimally invasive methods. Postmortem circulation was established in eight corpses to recreate an environment as close as possible to in vivo conditions. Mobile fluoroscopy and a percutaneous catheterization technique were used to deliver the material to the correct place. Once the valve was implanted, the heart and primary vessels were extracted to confirm its position. Postmortem circulation proved to be essential in several of the cadavers because it helped the clinicians to deliver the material and improve their implantation techniques. Due to the intravascular circulation, sites with substantial arteriosclerotic stenosis could be bypassed, which would have been impossible without perfusion. Although originally developed for postmortem investigations, this reperfusion technique could be useful for testing new medical devices intended for living patients.

  13. A three-axis flight simulator. [for testing and evaluating inertial measuring units, and flight platforms

    Science.gov (United States)

    Mason, M. G.

    1975-01-01

    A simulator is described, which was designed for testing and evaluating inertial measuring units, and flight platforms. Mechanical and electrical specifications for the outer, middle, and inner axis are presented. Test results are included.

  14. Closure Report for Corrective Action Unit 110: Areas 3 RWMS U-3ax/bl Disposal Unit, Nevada Test Site, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    J. L. Smith

    2001-08-01

    This Closure Report (CR) has been prepared for the Area 3 Radioactive Waste Management Site (RWMS) U-3ax/bl Disposal Unit Corrective Action Unit (CAU) 110 in accordance with the reissued (November 2000) Resource Conservation and Recovery Act (RCRA) Part B operational permit NEV HW009 (Nevada Division of Environmental Protection [NDEP], 2000) and the Federal Facility and Consent Order (FFACO) (NDEP et al., 1996). CAU 110 consists of one Corrective Action Site 03-23-04, described as the U-3ax/bl Subsidence Crater. Certifications of closure are located in Appendix A. The U-3ax/bl is a historic disposal unit within the Area 3 RWMS located on the Nevada Test Site (NTS). The unit, which was formed by excavating the area between two subsidence craters (U-3ax and U-3bl), was operationally closed in 1987. The U-3ax/bl disposal unit was closed under the RCRA, as a hazardous waste landfill. Existing records indicate that, from July 1968 to December 1987, U-3ax/bl received 2.3 x 10{sup 5} cubic meters (m{sup 3}) (8.12 x 10{sup 6} cubic feet [ft{sup 3}]) of waste. NTS atmospheric nuclear device testing generated approximately 95% of the total waste volume disposed of in U-3ax/bl; 80% of the total volume was generated from the Waste Consolidation Project. Area 3 is located in Yucca Flat, within the northeast quadrant of the NTS. The Yucca Flat watershed is a structurally closed basin encompassing an area of approximately 780 square kilometers (300 square miles). The structural geomorphology of Yucca Flat is typical of the Basin and Range Physiographic Province. Yucca Flat lies in one of the most arid regions of the country. Water balance calculations for Area 3 indicate that it is normally in a state of moisture deficit.

  15. STREAMLINED APPROACH FOR ENVIRONMENTAL RESTORATION PLAN FOR CORRECTIVE ACTION UNIT 116: AREA 25 TEST CELL C FACILITYNEVADA TEST SITE, NEVADA

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    This Streamlined Approach for Environmental Restoration Plan identifies the activities required for the closure of Corrective Action Unit 116, Area 25 Test Cell C Facility. The Test Cell C Facility is located in Area 25 of the Nevada Test Site approximately 25 miles northwest of Mercury, Nevada.

  16. Use of Silicon Carbide as Beam Intercepting Device Material: Tests, Issues and Numerical Simulations

    CERN Document Server

    Delonca, M; Gil Costa, M; Vacca, A

    2014-01-01

    Silicon Carbide (SiC) stands as one of the most promising ceramic material with respect to its thermal shock resistance and mechanical strengths. It has hence been considered as candidate material for the development of higher performance beam intercepting devices at CERN. Its brazing with a metal counterpart has been tested and characterized by means of microstructural and ultrasound techniques. Despite the positive results, its use has to be evaluated with care, due to the strong evidence in literature of large and permanent volumetric expansion, called swelling, under the effect of neutron and ion irradiation. This may cause premature and sudden failure, and can be mitigated to some extent by operating at high temperature. For this reason limited information is available for irradiation below 100°C, which is the typical temperature of interest for beam intercepting devices like dumps or collimators. This paper describes the brazing campaign carried out at CERN, the results, and the theoretical and numeric...

  17. A forensic laboratory tests the Berkeley microfabricated capillary array electrophoresis device.

    Science.gov (United States)

    Greenspoon, Susan A; Yeung, Stephanie H I; Johnson, Kelly R; Chu, Wai K; Rhee, Han N; McGuckian, Amy B; Crouse, Cecelia A; Chiesl, Thomas N; Barron, Annelise E; Scherer, James R; Ban, Jeffrey D; Mathies, Richard A

    2008-07-01

    Miniaturization of capillary electrophoresis onto a microchip for forensic short tandem repeat analysis is the initial step in the process of producing a fully integrated and automated analysis system. A prototype of the Berkeley microfabricated capillary array electrophoresis device was installed at the Virginia Department of Forensic Science for testing. Instrument performance was verified by PowerPlex 16 System profiling of single source, sensitivity series, mixture, and casework samples. Mock sexual assault samples were successfully analyzed using the PowerPlex Y System. Resolution was assessed using the TH01, CSF1PO, TPOX, and Amelogenin loci and demonstrated to be comparable with commercial systems along with the instrument precision. Successful replacement of the Hjerten capillary coating method with a dynamic coating polymer was performed. The accurate and rapid typing of forensic samples demonstrates the successful technology transfer of this device into a practitioner laboratory and its potential for advancing high-throughput forensic typing.

  18. Stress testing on silicon carbide electronic devices for prognostics and health management.

    Energy Technology Data Exchange (ETDEWEB)

    Kaplar, Robert James; Brock, Reinhard C.; Marinella, Matthew; King, Michael Patrick; Smith, Mark A.; Atcitty, Stanley

    2011-01-01

    Power conversion systems for energy storage and other distributed energy resource applications are among the drivers of the important role that power electronics plays in providing reliable electricity. Wide band gap semiconductors such as silicon carbide (SiC) and gallium nitride (GaN) will help increase the performance and efficiency of power electronic equipment while condition monitoring (CM) and prognostics and health management (PHM) will increase the operational availability of the equipment and thereby make it more cost effective. Voltage and/or temperature stress testing were performed on a number of SiC devices in order to accelerate failure modes and to identify measureable shifts in electrical characteristics which may provide early indication of those failures. Those shifts can be interpreted and modeled to provide prognostic signatures for use in CM and/or PHM. Such experiments will also lead to a deeper understanding of basic device physics and the degradation mechanisms behind failure.

  19. Phasor Measurement Unit and Phasor Data Concentrator test with Real Time Digital Simulator

    DEFF Research Database (Denmark)

    Diakos, Konstantinos; Wu, Qiuwei; Nielsen, Arne Hejde

    2014-01-01

    network to a more reliable, secure and economic operation. The implementation of these devices though, demands the warranty of a secure operation and high-accuracy performance. This paper describes the procedure of establishing a PMU (Phasor Measurement Unit)–PDC (Phasor Data Concentrator) platform...

  20. Combined prospective United States clinical study data for the GORE(®) HELEX(®) septal occluder device.

    Science.gov (United States)

    Rhodes, John F; Goble, Jake

    2014-05-01

    Our goal was to summarize the outcome for all subjects evaluated during a prospective clinical study in the United States with the GORE(®) HELEX(®) Septal Occluder for transcatheter repair of secundum atrial septal defects (ASD). The GORE(®) HELEX(®) Septal Occluder is currently utilized for repair of secundum ASD. No previous reports are available that summarize the combined clinical trial outcomes for this device. In the United States between 1999 and 2009, 435 subjects were enrolled through the Feasibility, Pivotal, Continued Access, and Post-Approval Studies. All subjects enrolled through these studies were collectively reviewed as the "study cohort." Clinical success, defined as a composite evaluation of safety and efficacy, is reported for subjects at the 12-month follow-up period. Of the 435 device subjects enrolled in the four clinical studies, 412 subjects were eligible for follow-up. Device efficacy, as represented by clinical closure at 12 months, was achieved in 98.3% of subjects, and in 99.5% of those receiving a device whose nominal diameter was greater or equal to twice the balloon sized defect diameter. Through 12 months following implantation, freedom from major adverse events was 95.2%. Together, these results yield a 93.0% composite clinical success at 12 months following the index procedure. The combined clinical study cohort represents the largest prospective, controlled clinical trial data set available for the GORE(®) HELEX(®) Septal Occluder. The clinical data presented in this report reaffirm the safety and efficacy of the GORE(®) HELEX(®) Septal Occluder when utilized for secundum atrial septal defect repair. Copyright © 2013 Wiley Periodicals, Inc.

  1. 10 CFR 430.24 - Units to be tested.

    Science.gov (United States)

    2010-01-01

    ... representation of the test data and calculations of a mechanical vapor-compression refrigeration cycle. The major components in the refrigeration cycle must be modeled as “fits” to manufacturer performance data or...

  2. Uniform Tests of File Converters Using Unit Cubes

    Science.gov (United States)

    2015-03-01

    and easy tool. This allows BRL–CAD to act as a hub for conversion and, in turn, increases the number of users of BRL–CAD. The converters all work...Design FASTGEN Fast Shotline Generator GDiff Geometry Differences GUI graphical user interface STL STereoLithography 6 1 DEFENSE... user to convert from different geometry file types. The goal of this project is to create a uniform test for every file converter. This test is the

  3. Evaluation of Human and Anthropomorphic Test Device Finite Element Models under Spaceflight Loading Conditions

    Science.gov (United States)

    Putnam, Jacob P.; Untaroiu, Costin; Somers. Jeffrey

    2014-01-01

    In an effort to develop occupant protection standards for future multipurpose crew vehicles, the National Aeronautics and Space Administration (NASA) has looked to evaluate the test device for human occupant restraint with the modification kit (THOR-K) anthropomorphic test device (ATD) in relevant impact test scenarios. With the allowance and support of the National Highway Traffic Safety Administration, NASA has performed a series of sled impact tests on the latest developed THOR-K ATD. These tests were performed to match test conditions from human volunteer data previously collected by the U.S. Air Force. The objective of this study was to evaluate the THOR-K finite element (FE) model and the Total HUman Model for Safety (THUMS) FE model with respect to the tests performed. These models were evaluated in spinal and frontal impacts against kinematic and kinetic data recorded in ATD and human testing. Methods: The FE simulations were developed based on recorded pretest ATD/human position and sled acceleration pulses measured during testing. Predicted responses by both human and ATD models were compared to test data recorded under the same impact conditions. The kinematic responses of the models were quantitatively evaluated using the ISO-metric curve rating system. In addition, ATD injury criteria and human stress/strain data were calculated to evaluate the risk of injury predicted by the ATD and human model, respectively. Results: Preliminary results show well-correlated response between both FE models and their physical counterparts. In addition, predicted ATD injury criteria and human model stress/strain values are shown to positively relate. Kinematic comparison between human and ATD models indicates promising biofidelic response, although a slightly stiffer response is observed within the ATD. Conclusion: As a compliment to ATD testing, numerical simulation provides efficient means to assess vehicle safety throughout the design process and further improve the

  4. Command decoder unit. [performance tests of data processing terminals and data converters for space shuttle orbiters

    Science.gov (United States)

    1976-01-01

    The design and testing of laboratory hardware (a command decoder unit) used in evaluating space shuttle instrumentation, data processing, and ground check-out operations is described. The hardware was a modification of another similar instrumentation system. A data bus coupler was designed and tested to interface the equipment to a central bus controller (computer). A serial digital data transfer mechanism was also designed. Redundant power supplies and overhead modules were provided to minimize the probability of a single component failure causing a catastrophic failure. The command decoder unit is packaged in a modular configuration to allow maximum user flexibility in configuring a system. Test procedures and special test equipment for use in testing the hardware are described. Results indicate that the unit will allow NASA to evaluate future software systems for use in space shuttles. The units were delivered to NASA and appear to be adequately performing their intended function. Engineering sketches and photographs of the command decoder unit are included.

  5. Design, Qualification and Integration Testing of the High-Temperature Resistance Temperature Device for Stirling Power System

    Science.gov (United States)

    Chan, Jack; Hill, Dennis H.; Elisii, Remo; White, Jonathan R.; Lewandowski, Edward J.; Oriti, Salvatore M.

    2015-01-01

    The Advanced Stirling Radioisotope Generator (ASRG), developed from 2006 to 2013 under the joint sponsorship of the United States Department of Energy (DOE) and National Aeronautics and Space Administration (NASA) to provide a high-efficiency power system for future deep space missions, employed Sunpower Incorporated's Advanced Stirling Convertors (ASCs) with operating temperature up to 840 C. High-temperature operation was made possible by advanced heater head materials developed to increase reliability and thermal-to-mechanical conversion efficiency. During a mission, it is desirable to monitor the Stirling hot-end temperature as a measure of convertor health status and assist in making appropriate operating parameter adjustments to maintain the desired hot-end temperature as the radioisotope fuel decays. To facilitate these operations, a Resistance Temperature Device (RTD) that is capable of high-temperature, continuous long-life service was designed, developed and qualified for use in the ASRG. A thermal bridge was also implemented to reduce the RTD temperature exposure while still allowing an accurate projection of the ASC hot-end temperature. NASA integrated two flight-design RTDs on the ASCs and assembled into the high-fidelity Engineering Unit, the ASRG EU2, at Glenn Research Center (GRC) for extended operation and system characterization. This paper presents the design implementation and qualification of the RTD, and its performance characteristics and calibration in the ASRG EU2 testing.

  6. ACR testing of a dedicated head SPECT unit.

    Science.gov (United States)

    Sensakovic, William F; Hough, Matthew C; Kimbley, Elizabeth A

    2014-07-08

    Physics testing necessary for program accreditation is rigorously defined by the ACR. This testing is easily applied to most conventional SPECT systems based on gamma camera technology. The inSPira HD is a dedicated head SPECT system based on a rotating dual clamshell design that acquires data in a dual-spiral geometry. The unique geometry and configuration force alterations of the standard ACR physics testing protocol. Various tests, such as intrinsic planar uniformity and/or resolution, do not apply. The Data Spectrum Deluxe Phantom used for conventional SPECT testing cannot fit in the inSPira HD scanner bore, making (currently) unapproved use of the Small Deluxe SPECT Phantom necessary. Matrix size, collimator type, scanning time, reconstruction method, and attenuation correction were all varied from the typically prescribed ACR instructions. Visible spheres, sphere contrast, visible rod groups, uniformity, and root mean square (RMS) noise were measured. The acquired SPECT images surpassed the minimum ACR requirements for both spatial resolution (9.5 mm spheres resolved) and contrast (6.4 mm rod groups resolved). Sphere contrast was generally high. Integral uniformity was 4% and RMS noise was 1.7%. Noise appeared more correlated than in images from a conventional SPECT scanner. Attenuation-corrected images produced from direct CT scanning of the phantom and a manufacturer supplied model of the phantom demonstrated negligible differences.

  7. Microfluidic devices for stem-cell cultivation, differentiation and toxicity testing

    Science.gov (United States)

    Becker, Holger; Hansen-Hagge, Thomas; Kurtz, Andreas; Mrowka, Ralf; Wölfl, Stefan; Gärtner, Claudia

    2017-02-01

    The development of new drugs is time-consuming, extremely expensive and often promising drug candidates fail in late stages of the development process due to the lack of suitable tools to either predict toxicological effects or to test drug candidates in physiologically relevant environments prior to clinical tests. We therefore try to develop diagnostic multiorgan microfluidic chips based on patient specific induced pluripotent stem cell (iPS) technology to explore liver dependent toxic effects of drugs on individual human tissues such as liver or kidney cells. Based initially on standardized microfluidic modules for cell culture, we have developed integrated microfluidic devices which contain different chambers for cell/tissue cultivation. The devices are manufactured using injection molding of thermoplastic polymers such as polystyrene or cyclo-olefin polymer. In the project, suitable surface modification methods of the used materials had to be explored. We have been able to successfully demonstrate the seeding, cultivation and further differentiation of modified iPS, as shown by the use of differentiation markers, thus providing a suitable platform for toxicity testing and potential tissue-tissue interactions.

  8. Turbine efficiency test on a large hydraulic turbine unit

    Institute of Scientific and Technical Information of China (English)

    YAN ZongGuo; ZHOU LingJiu; WANG ZhengWei

    2012-01-01

    The flow rate measurements are the most difficult part of efficiency tests on prototype hydraulic turbines.Among the numerous flow rate measurement methods,the Winter Kennedy method is preferred for measuring turbine flow rates,since it is convenient,practical and economical.This paper describes efficiency tests on a large 300 MW Francis turbine,with the flow rate measured using the Winter Kennedy method and the Winter Kennedy flow rate coefficient calibrated using the Gibson method.The measured turbine efficiency curve is then compared with the curve provided by the manufacturer.The CFD calculations including the spiral case are then used to analyze the influence with the coefficient K and index n in the Winter Kennedy flow rate formula on the flow rate measurement.The uncertainty values of n and K are a key reason for the differences between the curves obtained from the efficiency test and the curves provided by the manufacturer.

  9. Anomalous Thrust Production from an RF Test Device Measured on a Low-Thrust Torsion Pendulum

    Science.gov (United States)

    Brady, David; White, Harold G.; March, Paul; Lawrence, James T.; Davies, Frank J.

    2014-01-01

    produce thrust. Specifically, one test article contained internal physical modifications that were designed to produce thrust, while the other did not (with the latter being referred to as the "null" test article). Test data gathered includes torsion pendulum displacement measurements which are used to calculate generated force, still imagery in the visible spectrum to document the physical configuration, still imagery in the infrared spectrum to characterize the thermal environment, and video imagery. Post-test data includes static and animated graphics produced during RF resonant cavity characterization using the COMSOL Multiphysics® software application. Excerpts from all of the above are included and discussed in this paper. Lessons learned from test integration and operations include identification of the need to replace manual control of the resonant cavity target frequency with an automated frequency control capability. Future test plans include the development of an automatic frequency control circuit. Test results indicate that the RF resonant cavity thruster design, which is unique as an electric propulsion device, is producing a force that is not attributable to any classical electromagnetic phenomenon and therefore is potentially demonstrating an interaction with the quantum vacuum virtual plasma. Future test plans include independent verification and validation at other test facilities.

  10. Understanding the role of stimulation in reflexology: development and testing of a robotic device.

    Science.gov (United States)

    Flynn, L L; Bush, T R; Sikorskii, A; Mukherjee, R; Wyatt, G

    2011-09-01

    Reflexology is a common choice of women with breast cancer as supportive care during treatment. It involves stimulation of specific locations of the feet called reflexes using a specialised walking motion with the thumb of the reflexologist. Reflexology has shown potential for the successful management of cancer and treatment-related symptoms and improvement in physical functioning; however to date, the mechanism of action for these improvements is unknown. One confounder to the study of reflexology is the 'human factor'. To study the effects of the stimulation of the reflexes independent of the 'human factor', there is a need for an alternative method for the delivery of reflexology. The objective of this work was to design and create a robotic reflexology device that would deliver a breast cancer-specific reflexology protocol to the feet of patients. A prototype robotic reflexology device was developed and tested for feasibility, safety and acceptability with breast cancer survivors (n= 13), and preliminary efficacy in symptom management and enhanced functional status with a sample of women undergoing chemotherapy for breast cancer (n= 13). Safety, feasibility and acceptability were established, and significant improvements from pre- to post-device-delivered reflexology were seen in symptom severity among women on chemotherapy.

  11. Development, Test and Validation of a Mechatronic Device for Spasticity Quantification

    Directory of Open Access Journals (Sweden)

    João F. Ferreira

    2013-05-01

    Full Text Available Spasticity is a common pathological phenomenon in clinical practices, frequently expressed as a stroke, multiple sclerosis or cerebral palsy. The accurate quantification of spasticity allows early action to prevent the potentially irreversible consequences. The aim of this work is to develop and implement a mechatronic device for the accurate quantification of spasticity, which is able to differentiate spasticity from other motor disorders. The proposed method is based on the quantification of the tonic stretch reflex threshold (TSRT for the assessment of the range of motion of the limb affected by spasticity. In order to validate the developed device, experimental trials have been conducted, considering the flexor muscle of the elbow joint. The developed device was tested, first in a laboratory environment with healthy subjects and secondly, in a clinical environment with the collaboration of patients with spasticity. The evaluations in th clinical environment were performed on three different days in order to evaluate the reproducibility of the obtained results. The experimental trials confirm the sensibility, reproducibility and reliability of spasticity quantification based on the TSRT method. This project has been developed in cooperation with the Hospital of Braga and Fisimaia rehabilitation clinic, both in Portugal.

  12. Ground Tests and In-Orbit Performance of Variable Emittance Device Based on Manganese Oxide

    Science.gov (United States)

    Tachikawa, Sumitaka; Ohnishi, Akira; Nakamura, Yasuyuki; Okamoto, Akira

    A new thermal control material named the Smart Radiation Device (SRD) has shown improvement in development. The SRD can be used as a variable emittance radiator that controls the heat radiated into deep space without assistances of any electrical instruments or mechanical parts. Its total hemispherical emittance changes from low to high as the temperature increases. This new device reduces the energy consumption of the on-board heater, and decreases the weight and the cost of the thermal control system (TCS). Space environmental simulation tests on the ground were performed, and the first generation of the SRD has been demonstrating success on the MUSES-C ‘HAYABUSA’ spacecraft that was launched in May 2003. During its cruise on the orbit, the distance from the spacecraft to the sun varied from 0.86AU to 1.70AU. As the spacecraft experienced solar intensity variation by a factor 4, it was effective to use the variable emittance radiator for decreasing the heater power. In-orbit temperature indicated that the SRD had successfully minimized component temperature variation and saved heater power, as expected. With the opportunity to validate the SRD in space, this lightweight and low cost thermal control device offers a possibility for flexible thermal control on future spacecrafts.

  13. Vibration Mitigation without Dissipative Devices: First Large-Scale Testing of a State Switched Inducer

    Directory of Open Access Journals (Sweden)

    Daniel Tirelli

    2014-01-01

    Full Text Available A new passive device for mitigating cable vibrations is proposed and its efficiency is assessed on 45-meter long taut cables through a series of free and forced vibration tests. It consists of a unilateral spring attached perpendicularly to the cable near the anchorage. Because of its ability to change the cable dynamic behaviour through intermittent activation, the device has been called state switched inducer (SSI. The cable behaviour is shown to be deeply modified by the SSI: the forced vibration response is anharmonicc and substantially reduced in amplitude whereas the free vibration decay is largely sped up through a beating phenomenon. The vibration mitigation effect is mainly due to the activation and coupling of various vibration modes, as evidenced in the response spectra of the equipped cable. This first large-scale experimental campaign shows that the SSI outperforms classical passive devices, thus paving the way to a new kind of low-cost vibration mitigation systems which do not rely on dissipation.

  14. Prevalence of major risk factors and use of screening tests for cancer in the United States.

    Science.gov (United States)

    Fedewa, Stacey A; Sauer, Ann Goding; Siegel, Rebecca L; Jemal, Ahmedin

    2015-04-01

    Much of the suffering and death from cancer could be prevented by more systematic efforts to reduce tobacco use, improve diet, increase physical activity, reduce obesity, and expand the use of established screening tests. Monitoring the prevalence of cancer risk factors and screening is important to measure progress and strengthen cancer prevention and early detection efforts. In this review article, we provide recent prevalence estimates for several cancer risk factors, including tobacco, obesity, physical activity, nutrition, ultraviolet radiation exposure as well as human papillomavirus and hepatitis B vaccination coverage and cancer screening prevalence in the United States. In 2013, cigarette smoking prevalence was 17.8% among adults nationally, but ranged from 10.3% in Utah to 27.3% in West Virginia. In addition, 15.7% of U.S. high school students were current smokers. In 2011-2012, obesity prevalence was high among both adults (34.9%) and adolescents (20.5%), but has leveled off since 2002. About 20.2% of high school girls were users of indoor tanning devices, compared with 5.3% of boys. In 2013, cancer screening prevalence ranged from 58.6% for colorectal cancer to 80.8% for cervical cancer and remains low among the uninsured, particularly for colorectal cancer screening where only 21.9% of eligible adults received recommended colorectal cancer screening. ©2015 American Association for Cancer Research.

  15. A system for measuring an optical spectral response and/or IV data of a photoelectric device under test

    NARCIS (Netherlands)

    Elshinawy, M.; Heirman, S.G.M.; Melsken, J.; Fischer, M.

    2015-01-01

    A system for measuring an optical spectral response or property and/or IV data of a device or object under test (9), comprising in optically coupled sequence: a broadband light source (1) for emitting light of a prede- fined spectrum, a slit and/or light guide (2), a wavelength dispersive device (3)

  16. EquiMar : Equitable Testing and Evaluation of Marine Energy Extraction Devices in terms of Performance, Cost and Environmental Impact

    DEFF Research Database (Denmark)

    McCombes, T; Johnstone, C.; Holmes, B.

    of current practices adopted for tank testing of small prototype devices and the development of new methods enabling device performance assessment and benchmarking. The contents of this report will be tightly integrated with the remaining deliverables of WP 3, specifically Deliverable 3.4.a...

  17. Quality control test for electronic portal imaging device using QC-3 phantom with PIPSpro

    Directory of Open Access Journals (Sweden)

    Birendra Kumar Rout

    2014-12-01

    Full Text Available Purpose:A Quality control (QC test suitable for routinely daily use has been established for electronic portal imaging device (EPID using PIPSpro software version 4.4 (Standard Imaging, Middleton, WI. It provides an objective and quantitative test for tolerable image quality on the basis of the high contrast spatial resolution, the contrast-to-noise ratio (CNR and noise.Methods: The test uses a QC-3 phantom consisting of five sets of high contrast rectangular bar patterns with spatial frequeinces of 0.10, 0.20, 0.25, 0.43 and 0.75 lp/mm using 6MV and 15MV photon energy for accquiring high quality images. A “base line” value for the relative square wave modulation transfer function (RMTF, CNR and Noise data was obtained during a one week calibration period and one month test period.Results: Subsequent measurements shows significant deviations from baseline values, resulting in warning messages “potential problems in system performance”. The QC test uses high contrast spatial resolution and CNR for the system with acceptable performance. Conclusion: The method provides an automatic, objective, and sensitive measure of the system's imaging performance. This is a useful implementation during acceptance testing, commissioning, and routine quality control.

  18. Anomalous Thrust Production from an RF Test Device Measured on a Low-Thrust Torsion Pendulum

    Science.gov (United States)

    Brady, David A.; White, Harold G.; March, Paul; Lawrence, James T.; Davies, Frank J.

    2014-01-01

    This paper describes the test campaigns designed to investigate and demonstrate viability of using classical magnetoplasmadynamics to obtain a propulsive momentum transfer via the quantum vacuum virtual plasma. This paper will not address the physics of the quantum vacuum plasma thruster (QVPT), but instead will describe the recent test campaign. In addition, it contains a brief description of the supporting radio frequency (RF) field analysis, lessons learned, and potential applications of the technology to space exploration missions. During the first (Cannae) portion of the campaign, approximately 40 micronewtons of thrust were observed in an RF resonant cavity test article excited at approximately 935 megahertz and 28 watts. During the subsequent (tapered cavity) portion of the campaign, approximately 91 micronewtons of thrust were observed in an RF resonant cavity test article excited at approximately 1933 megahertz and 17 watts. Testing was performed on a low-thrust torsion pendulum that is capable of detecting force at a single-digit micronewton level. Test campaign results indicate that the RF resonant cavity thruster design, which is unique as an electric propulsion device, is producing a force that is not attributable to any classical electromagnetic phenomenon and therefore is potentially demonstrating an interaction with the quantum vacuum virtual plasma.

  19. BRCA mutation genetic testing implications in the United States.

    Science.gov (United States)

    Bayraktar, Soley; Arun, Banu

    2017-02-01

    BRCA mutation carriers have a very high risk of breast and ovarian cancer by age 70, in the ranges 47%-66% and 40%-57%, respectively. Additionally, women with BRCA mutation-associated breast cancer also have an elevated risk of other or secondary malignancies. Fortunately, the breast and ovarian cancer outcome for BRCA1/2 mutation carriers is at least as good as for non-carriers with chemoprevention, prophylactic surgeries and appropriate use of therapies. Therefore, identification of those who might have a mutation is important so that genetic counseling, testing, screening and prevention strategies can be applied in a timely manner. This article reviews the impact of genetic testing in general, timing of genetic testing after diagnosis and prior knowledge of mutation status in BRCA carriers with newly diagnosed breast cancer. Additionally, risk-reducing surgeries including the prophylactic contralateral mastectomy, and bilateral salpingo-oophorectomy and the sensitivity of BRCA-defective breast cancer cell lines to differential chemotherapeutic agents will be discussed.

  20. Comparison of a semiautomated hand-held device to test minimal erythema dose before narrowband ultraviolet B phototherapy with the conventional method using matched doses.

    Science.gov (United States)

    Lynch, M; Carroll, F; Kavanagh, A; Honari, B; Collins, P

    2014-12-01

    A semiautomated hand-held device has been introduced in some phototherapy centres to establish the minimal erythema dose (MED) before treatment with narrowband ultraviolet (NBUV) B. To compare the semiautomated hand-held device with the conventional method of MED testing (a UV-opaque template and a panel of UVB fluorescent tubes), using the same series of incremented doses. Twenty-four patients referred for treatment with NBUVB phototherapy were included. Each patient had MED testing with the conventional method and the semiautomated hand-held device at the same level of the left and right back. The results were read by four investigators each time. The semiautomated hand-held device was a significant estimator of the MED using the conventional panel method (P < 0.001; r = 0.97). The average ratio of the hand-held MED to the conventional MED was 67%. The mean difference between the methods was 165 mJ/cm(2) . The interobserver test showed very high agreement for both methods of MED testing (Cronbach α coefficient 0.97 for the hand-held MED tester vs. 0.93 for the conventional method). The semiautomated hand-held device MED results were lower than that of the conventional panel method and may prolong the treatment course by 2-3 treatments. The hand-held tester is a fast and reproducible method, and may allow more phototherapy units, limited by staff and time, to do MED testing. © 2014 European Academy of Dermatology and Venereology.

  1. Vertical shaking table tests on the structure with viscoelastic multi-dimensional earthquake isolation and mitigation devices

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    The viscoelastic multi-dimensional earthquake isolation and mitigation device is a new kind of passive control device, which can perform its "name-giving" task of earthquake isolation and earthquake mitigation simultaneously. In order to quantify its vertical earthquake isolation and mitigation effect on structures, firstly, shaking table tests on steel frame structures with and without the devices were carried out; secondly, analysis on dynamic characteristics and dynamic responses of the structures was also performed; furthermore, the finite element analytical results and the experimental results were compared. It can be shown from the analytical and experimental results that the devices have noticeable earthquake isolation and mitigation effect in the vertical direction.

  2. EquiMar : Equitable Testing and Evaluation of Marine Energy Extraction Devices in terms of Performance, Cost and Environmental Impact

    DEFF Research Database (Denmark)

    McCombes, T; Johnstone, C.; Holmes, B.

    development funding or promote a specific wave or tidal energy device. Since no standards exist, the data produced may be misinterpreted or inaccurately presented, which in turn may lead to failure to live up to performance expectations, as devices scale up in size. This report aims to identify limitations...... of current practices adopted for tank testing of small prototype devices and the development of new methods enabling device performance assessment and benchmarking. The contents of this report will be tightly integrated with the remaining deliverables of WP 3, specifically Deliverable 3.4.a...

  3. Rapid prototyping compliant arterial phantoms for in-vitro studies and device testing

    Directory of Open Access Journals (Sweden)

    Biglino Giovanni

    2013-01-01

    Full Text Available Abstract Background Compliant vascular phantoms are desirable for in-vitro patient-specific experiments and device testing. TangoPlus FullCure 930® is a commercially available rubber-like material that can be used for PolyJet rapid prototyping. This work aims to gather preliminary data on the distensibility of this material, in order to assess the feasibility of its use in the context of experimental cardiovascular modelling. Methods The descending aorta anatomy of a volunteer was modelled in 3D from cardiovascular magnetic resonance (CMR images and rapid prototyped using TangoPlus. The model was printed with a range of increasing wall thicknesses (0.6, 0.7, 0.8, 1.0 and 1.5 mm, keeping the lumen of the vessel constant. Models were also printed in both vertical and horizontal orientations, thus resulting in a total of ten specimens. Compliance tests were performed by monitoring pressure variations while gradually increasing and decreasing internal volume. Knowledge of distensibility was thus derived and then implemented with CMR data to test two applications. Firstly, a patient-specific compliant model of hypoplastic aorta suitable for connection in a mock circulatory loop for in-vitro tests was manufactured. Secondly, the right ventricular outflow tract (RVOT of a patient necessitating pulmonary valve replacement was printed in order to physically test device insertion and assess patient’s suitability for percutaneous pulmonary valve intervention. Results The distensibility of the material was identified in a range from 6.5 × 10-3 mmHg-1 for the 0.6 mm case, to 3.0 × 10-3 mmHg-1 for the 1.5 mm case. The models printed in the vertical orientation were always more compliant than their horizontal counterpart. Rapid prototyping of a compliant hypoplastic aorta and of a RVOT anatomical model were both feasible. Device insertion in the RVOT model was successful. Conclusion Values of distensibility, compared with literature data, show that Tango

  4. Amplitude Test for Input Devices for System Control in Immersive Virtual Environment

    DEFF Research Database (Denmark)

    Stenholt, Rasmus; Thornemann Hansen, Nina; Hald, Kasper

    2014-01-01

    In this study, the amplitudes best suited to compare four input devices are examined in the context of a pointer-based system control interface for immersive virtual environments. The interfaces are based on a pen and tablet, a touch tablet, hand-tracking using Kinect and a Wii Nunchuk analog sti...... menu using each combination of amplitude and interface. The amplitudes to be used for future experiments were found. Also, the movement times for the interfaces do not fit the predictions of Fitts' law.......In this study, the amplitudes best suited to compare four input devices are examined in the context of a pointer-based system control interface for immersive virtual environments. The interfaces are based on a pen and tablet, a touch tablet, hand-tracking using Kinect and a Wii Nunchuk analog stick....... This is done as a preliminary study in order to be able to compare the interfaces with the goal of evaluating them in the context of using virtual environments in a class lecture. Five amplitudes are tested for each of the four interfaces by having test participants mark menu elements in an eight-part radial...

  5. System for measurement and automatic regulation of gas flow within an oil aging test device

    Directory of Open Access Journals (Sweden)

    Žigić Aleksandar

    2014-01-01

    Full Text Available This paper describes a system within an oil aging test device that serves for measurement and automatic regulation of gas flow. Following an already realized system that continuously monitors, logs, and regulates transformer oil temperature during the aging process and maintains temperature consistency within strict limits, a model of a flow meter and regulator of air or oxygen through transformer oil samples is developed. A special feature of the implemented system is the measurement of very small gas flows. A short technical description of the realized system is given with a functional block diagram. The basic technical characteristics of the system are specified, and the operating principles and application of the system are described. The paper also gives performance test results in a real exploitation environment.

  6. Development and field tests of a damping controller to mitigate electromechanical oscillations on large diesel generating units

    Energy Technology Data Exchange (ETDEWEB)

    Nogueira, Fabricio G.; Barreiros, Jose A.L.; Barra, Walter Jr.; Costa, Carlos T. Jr. [Universidade Federal do Para (UFPA), Instituto de Tecnologia, Faculdade de Engenharia Eletrica, Campus Universitario do Guama, CEP: 66075-900, Belem (Brazil); Ferreira, Andre M.D. [Instituto Federal de Educacao, Ciencia e Tecnologia do Para (IFPA), Campus Belem, Departamento de Controle e Processos Industriais, Av. Almirante Barroso, 1155 (Marco), CEP: 66093-020, Belem (Brazil)

    2011-02-15

    This paper presents the development and field tests of a digital damping controller designed to mitigate intra-plant electromechanical oscillations via the speed governor system of fast acting units. The controller performance is assessed on an 18-MVA diesel generating unit, at Santana Power Plant (Amapa State, Amazon Region at Northern Brazil). In order to design the damping control law, a set of parametric ARX models representing the plant dynamics at several load conditions, are previously identified from data collected on field tests. The damping controller gains are calculated by using the identified ARX models parameters as inputs to a discrete-time pole-placement design method (pole-shifting) and then embedded on a DSP based microcontroller digital system, for field tests assessment. The digital damping controller modulates the diesel engine inlet valve position according to the observed oscillation on the measured electric power, using a PWM device, which is specially developed to this application. The experimental results shown the good performance of the developed controller on damping efficiently the electromechanical oscillations observed between generating units at Santana Power Plant. (author)

  7. A proposed hardness assurance test methodology for bipolar linear circuits and devices in a space ionizing radiation environment

    Energy Technology Data Exchange (ETDEWEB)

    Pease, R.L. [RLP Research, Albuquerque, NM (United States); Brown, D.B. [Naval Research Lab., Washington, DC (United States); Cohn, L. [Defense Special Weapons Agency, Alexandria, VA (United States)] [and others

    1997-04-01

    A hardness assurance test approach has been developed for bipolar linear circuits and devices in space. It consists of a screen for dose rate sensitivity and a characterization test method to develop the conditions for a lot acceptance test at high dose rate.

  8. A novel microbead-based microfluidic device for rapid bacterial identification and antibiotic susceptibility testing.

    Science.gov (United States)

    He, J; Mu, X; Guo, Z; Hao, H; Zhang, C; Zhao, Z; Wang, Q

    2014-12-01

    Effective treatment of infectious diseases depends on the ability to rapidly identify the infecting bacteria and the use of sensitive antibiotics. The currently used identification assays usually take more than 72 h to perform and have a low sensitivity. Herein, we present a microbead-based microfluidic platform that is highly sensitive and rapid for bacterial detection and antibiotic sensitivity testing. The platform includes four units, one of which is used for bacterial identification and the other three are used for susceptibility testing. Our results showed that Escherichia coli O157 at a cell density range of 10(1)-10(5) CFU/μL could be detected within 30 min. Additionally, the effects of three antibiotics on E. coli O157 were evaluated within 4-8 h. Overall, this integrated microbead-based microdevice provides a sensitive, rapid, reliable, and highly effective platform for the identification of bacteria, as well as antibiotic sensitivity testing.

  9. Determining the Performance of Fluorescence Molecular Imaging Devices Using Traceable Working Standards With SI Units of Radiance.

    Science.gov (United States)

    Zhu, Banghe; Rasmussen, John C; Litorja, Maritoni; Sevick-Muraca, Eva M

    2016-03-01

    To date, no emerging preclinical or clinical near-infrared fluorescence (NIRF) imaging devices for noninvasive and/or surgical guidance have their performances validated on working standards with SI units of radiance that enable comparison or quantitative quality assurance. In this work, we developed and deployed a methodology to calibrate a stable, solid phantom for emission radiance with International System of Units (SI) units of mW ·sr(-1) ·cm(-2) for use in characterizing the measurement sensitivity of ICCD and IsCMOS detection, signal-to-noise ratio, and contrast. In addition, at calibrated radiances, we assess transverse and lateral resolution of ICCD and IsCMOS camera systems. The methodology allowed demonstration of superior SNR of the ICCD over the IsCMOS technology and superior resolution of the IsCMOS over the ICCD approach. Contrast depended upon the camera settings (binning and integration time) and gain of intensifier. Finally, because the architecture of CMOS and CCD camera systems results in vastly different performance, we comment on the utility of these technologies for small animal imaging as well as clinical applications for noninvasive and surgical guidance.

  10. Hydrologic resources management program and underground test area operable unit fy 1997

    Energy Technology Data Exchange (ETDEWEB)

    Smith, D. F., LLNL

    1998-05-01

    This report present the results of FY 1997 technical studies conducted by the Lawrence Livermore National Laboratory (LLNL) as part of the Hydrology and Radionuclide Migration Program (HRMP) and Underground Test Area Operable Unit (UGTA). The HRMP is sponsored by the US Department of Energy to assess the environmental (radiochemical and hydrologic) consequences of underground nuclear weapons testing at the Nevada Test Site.

  11. Efficient Market Hypothesis in South Africa: Evidence from Linear and Nonlinear Unit Root Tests

    Directory of Open Access Journals (Sweden)

    Andrew Phiri

    2015-12-01

    Full Text Available This study investigates the weak form efficient market hypothesis (EMH for five generalized stock indices in the Johannesburg Stock Exchange (JSE using weekly data collected from 31st January 2000 to 16th December 2014. In particular, we test for weak form market efficiency using a battery of linear and nonlinear unit root testing procedures comprising of the classical augmented Dickey-Fuller (ADF tests, the two-regime threshold autoregressive (TAR unit root tests described in Enders and Granger (1998 as well as the three-regime unit root tests described in Bec, Salem, and Carrasco (2004. Based on our empirical analysis, we are able to demonstrate that whilst the linear unit root tests advocate for unit roots within the time series, the nonlinear unit root tests suggest that most stock indices are threshold stationary processes. These results bridge two opposing contentions obtained from previous studies by concluding that under a linear framework the JSE stock indices offer support in favour of weak form market efficiency whereas when nonlinearity is accounted for, a majority of the indices violate the weak form EMH.

  12. Closure Plan for Corrective Action Unit 110: Area 3 RWMS U-3ax/bl Disposal Unit, Nevada Test Site, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    T. M. Fitzmaurice

    2000-08-01

    This Closure Plan has been prepared for the Area 3 RWMS U-3ax/bl Disposal Unit Corrective Action Unit 110 in accordance with the Federal Facility and Consent Order (Nevada Division of Environmental Protection [NDEP] et al., 1996). The U-3ax/bl is a historic disposal unit within the Area 3 Radioactive Waste Management Site located on the Nevada Test Site (NTS). The unit, which was formed by excavating the area between two subsidence craters (U-3ax and U-3bl), was operationally closed in 1987. The U-3ax/bl disposal unit is scheduled for permanent closure under the Resource Conservation and Recovery Act as a hazardous waste landfill. Existing records indicate that, from July 1968 to December 1987, U-3ax/bl received 2.3 x 10{sup 5} cubic meters (8.12 x 10{sup 6} cubic feet) of waste. NTS nuclear device testing generated approximately 95 percent of the total volume disposed of in U-3ax/bl, the majority of which came from the Waste Consolidation Project (80 percent of the total volume) (Elletson and Johnejack, 1995). Area 3 is located in Yucca Flat, within the northeast quadrant of the NTS. The Yucca Flat watershed is a structurally closed basin encompassing an area of approximately 780 square kilometers (300 square miles). The structural geomorphology of Yucca Flat is typical of the Basin and Range Physiographic Province. Yucca Flat lies in one of the most arid regions of the country. Water balance calculations for Area 3 indicate that it is continuously in a state of moisture deficit. The U-3ax/bl Disposal Unit will be closed in place by installing a Resource Conservation and Recovery Act equivalent cover. Following cover construction a fence will be installed around the cover to prevent accidental damage to the cover. Post-closure monitoring will consist of site inspections to determine the condition of the engineered cover and cover performance monitoring using Time-Domain Reflectometry arrays to monitor moisture migration in the cover. Any identified maintenance and

  13. Intex Tests Performed on Hydro Unit no2 from HPP Ruieni before and after Refurbishment

    Directory of Open Access Journals (Sweden)

    Adrian Cuzmoş

    2013-05-01

    Full Text Available The paper work presents the results of index tests performed on HPP Ruieni hydro unit no 2 before and after refurbishment, using for discharge measurements the Winter-Kennedy method.

  14. Novel exposure units for at-home personalized testing of electromagnetic sensibility

    NARCIS (Netherlands)

    Huss, Anke; Murbach, Manuel; van Moorselaar, Imke; Kuster, Niels; van Strien, Rob; Kromhout, Hans; Vermeulen, Roel; Slottje, Pauline

    2016-01-01

    Previous experimental studies on electromagnetic hypersensitivity have been criticized regarding inflexibility of choice of exposure and of study locations. We developed and tested novel portable exposure units that can generate different output levels of various extremely low frequency magnetic fie

  15. United States Nuclear Tests, July 1945 through September 1992, December 2000

    Energy Technology Data Exchange (ETDEWEB)

    U.S. Department of Energy, Nevada Operations Office

    2000-12-01

    This document list chronologically and alphabetically by name all nuclear tests and simultaneous detonations conducted by the United States from July 1945 through September 1992. Revision 15, dated December 2000.

  16. United States Nuclear Tests, July 1945 through September 1992, September 2015

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2015-09-01

    This document lists chronologically and alphabetically by name all nuclear tests and simultaneous detonations conducted by the United States from July 1945 through September 1992. This is Revision 16, dated September 2015.

  17. Lessons from wet gas flow metering systems using differential measurements devices: Testing and flow modelling results

    Energy Technology Data Exchange (ETDEWEB)

    Cazin, J.; Couput, J.P.; Dudezert, C. et al

    2005-07-01

    A significant number of wet gas meters used for high GVF and very high GVF are based on differential pressure measurements. Recent high pressure tests performed on a variety of different DP devices on different flow loops are presented. Application of existing correlations is discussed for several DP devices including Venturi meters. For Venturi meters, deviations vary from 9% when using the Murdock correlation to less than 3 % with physical based models. The use of DP system in a large domain of conditions (Water Liquid Ratio) especially for liquid estimation will require information on the WLR This obviously raises the question of the gas and liquid flow metering accuracy in wet gas meters and highlight needs to understand AP systems behaviour in wet gas flows (annular / mist / annular mist). As an example, experimental results obtained on the influence of liquid film characteristics on a Venturi meter are presented. Visualizations of the film upstream and inside the Venturi meter are shown. They are completed by film characterization. The AP measurements indicate that for a same Lockhart Martinelli parameter, the characteristics of the two phase flow have a major influence on the correlation coefficient. A 1D model is defined and the results are compared with the experiments. These results indicate that the flow regime influences the AP measurements and that a better modelling of the flow phenomena is needed even for allocation purposes. Based on that, lessons and way forward in wet gas metering systems improvement for allocation and well metering are discussed and proposed. (author) (tk)

  18. A New Device for Mechanical Testing of Blood Vessels at Cryogenic Temperatures

    Science.gov (United States)

    Jimenez Rios, Jorge L.; Rabin, Yoed

    2008-01-01

    As part of an ongoing program to study the thermo-mechanical effects associated with cryopreservation via vitrification (vitreous in Latin means glassy), the current study focuses on the development of a new device for mechanical testing of blood vessels at cryogenic temperatures. This device is demonstrated on a bovine carotid artery model, permeated with the cryoprotectant cocktail VS55 and a reference solution of 7.05M DMSO, below glass transition. Results are also presented for crystallized specimens, in the absence of cryoprotectants. Results indicate that the elastic modulus of a specimen with no cryoprotectant, at about −140°C (8.6°C and 15.5°C below the glass transition temperature of 7.05M DMSO and VS55, respectively), is 1038.8 ± 25.2 MPa, which is 8% and 3% higher than that of a vitrified specimen permeated with 7.05M DMSO and VS55, respectively. The elastic modulus of a crystallized material at −50°C is lower by ~20% lower from that at −140°C. PMID:18958183

  19. Development of a simple test device for spindle error measurement using a position sensitive detector

    Science.gov (United States)

    Liu, Chien-Hung; Jywe, Wen-Yuh; Lee, Hau-Wei

    2004-09-01

    A new spindle error measurement system has been developed in this paper. It employs a design development rotational fixture with a built-in laser diode and four batteries to replace a precision reference master ball or cylinder used in the traditional method. Two measuring devices with two position sensitive detectors (one is designed for the measurement of the compound X-axis and Y-axis errors and the other is designed with a lens for the measurement of the tilt angular errors) are fixed on the machine table to detect the laser point position from the laser diode in the rotational fixture. When the spindle rotates, the spindle error changes the direction of the laser beam. The laser beam is then divided into two separated beams by a beam splitter. The two separated beams are projected onto the two measuring devices and are detected by two position sensitive detectors, respectively. Thus, the compound motion errors and the tilt angular errors of the spindle can be obtained. Theoretical analysis and experimental tests are presented in this paper to separate the compound errors into two radial errors and tilt angular errors. This system is proposed as a new instrument and method for spindle metrology.

  20. Review of Mechanical Testing and Modelling of Thrombus Material for Vascular Implant and Device Design.

    Science.gov (United States)

    Johnson, S; Duffy, S; Gunning, G; Gilvarry, M; McGarry, J P; McHugh, P E

    2017-08-28

    A thrombus or blood clot is a solid mass, made up of a network of fibrin, platelets and other blood components. Blood clots can form through various pathways, for example as a result of exposed tissue factor from vascular injury, as a result of low flow/stasis, or in very high shear flow conditions. Embolization of cardiac or vascular originating blood clots, causing an occlusion of the neurovasculature, is the major cause of stroke and accounts for 85% of all stroke. With mechanical thrombectomy emerging as the new standard of care in the treatment of acute ischemic stroke (AIS), the need to generate a better understanding of the biomechanical properties and material behaviour of thrombus material has never been greater, as it could have many potential benefits for the analysis and performance of these treatment devices. Defining the material properties of a thrombus has obvious implications for the development of these treatment devices. However, to-date this definition has not been adequately established. While some experimentation has been performed, model development has been extremely limited. This paper reviews the previous literature on mechanical testing of thrombus material. It also explores the use of various constitutive and computational models to model thrombus formation and material behaviour.

  1. Direct Shear Tests of Sandstone Under Constant Normal Tensile Stress Condition Using a Simple Auxiliary Device

    Science.gov (United States)

    Cen, Duofeng; Huang, Da

    2017-06-01

    Tension-shear failure is a typical failure mode in the rock masses in unloading zones induced by excavation or river incision, etc., such as in excavation-disturbed zone of deep underground caverns and superficial rocks of high steep slopes. However, almost all the current shear failure criteria for rock are usually derived on the basis of compression-shear failure. This paper proposes a simple device for use with a servo-controlled compression-shear testing machine to conduct the tension-shear tests of cuboid rock specimens, to test the direct shear behavior of sandstone under different constant normal tensile stress conditions ( σ = -1, -1.5, -2, -2.5 and -3 MPa) as well as the uniaxial tension behavior. Generally, the fracture surface roughness decreases and the proportion of comminution areas in fracture surface increases as the change of stress state from tension to tension-shear and to compression-shear. Stepped fracture is a primary fracture pattern in the tension-shear tests. The shear stiffness, shear deformation and normal deformation (except the normal deformation for σ = -1 MPa) decrease during shearing, while the total normal deformation containing the pre-shearing portion increases as the normal tensile stress level (| σ|) goes up. Shear strength is more sensitive to the normal tensile stress than to the normal compressive stress, and the power function failure criterion (or Mohr envelope form of Hoek-Brown criterion) is examined to be the optimal criterion for the tested sandstone in the full region of tested normal stress in this study.

  2. Reliability of a new supination resistance measurement device and validation of the manual supination resistance test.

    Science.gov (United States)

    Griffiths, Ian B; McEwan, Islay M

    2012-01-01

    Kinematic observations are inconsistent in predicting lower-extremity injury risk, and research suggests that kinetic variables may be more important in this regard. Before kinetics can be prospectively investigated, we need reliable ways of measuring them clinically. A measurement instrument was manufactured that closely mirrors a manual test used to clinically estimate supination resistance force. The reliability of the instrument and the validity of the clinical test were investigated. The left feet of 26 healthy individuals (17 men and 9 women; mean ± SD age, 25.9 ± 9.2 years; mean ± SD weight, 77.7 ± 13.3 kg) were assessed. Foot Posture Index (FPI-6), manual supination resistance, and machine supination resistance were measured. Intrarater and interrater reliability of all of the measurements were calculated. Correlations of the supination resistance measured by the device with FPI-6, the manual supination resistance test, and body weight were investigated. Interrater reliability of all of the measurements was generally poor. The supination resistance machine correlated highly with the manual supination test for the rater experienced with its use. Supination resistance measurements correlated poorly with the FPI-6 and weakly with body weight. The supination resistance machine was shown to have sufficient limits of agreement for the study, but improvements need to be made for more meaningful research going forward. In this study, the force required to supinate a foot was independent of its posture, and approximately 12% of it was explained by body weight. Further work is required with a much larger sample size to build regression models that sufficiently predict supination resistance force and that will be of clinical use. The manual supination test is a valid clinical test for clinicians experienced in its use.

  3. Panel Unit Root Test with Nonlinear Mean Reversion and Smooth Breaks

    OpenAIRE

    Lau, Chi Keung Marco; Chau, Frankie; Deesomsak, Rataporn

    2011-01-01

    This paper extends the unit root test of Christopoulos and Leòn-Ledesma (2010) to accommodate not only structural breaks and non-linear mean reversion, but also the contemporaneous cross-sectional dependence commonly found in panel dataset. The proposed test presents good finite sample properties and its applications on four major ASEAN countries’ real exchange rates show that the unit root hypothesis could be rejected, supporting their long-run Purchasing Power Parity (PPP) again...

  4. Electrostatic protocol treatment lens. The purpose of this device is to transport Antiprotons from the new ELENA storage beam to all AD experiments. The electrostatic device was successfully tested in ASACUSA two weeks ago.

    CERN Multimedia

    Maximilien Brice

    2012-01-01

    Electrostatic protocol treatment lens. The purpose of this device is to transport Antiprotons from the new ELENA storage beam to all AD experiments. The electrostatic device was successfully tested in ASACUSA two weeks ago.

  5. Testing of the United Stirling 4-95 solar Stirling engine on test bed concentrator

    Science.gov (United States)

    Nelving, H. G.

    1984-01-01

    The objectives with the testing, test set-ups, component designs, and the results of the testing of the solar Stirling engine in a parabolic dish system are presented. The most important tests are characterization of receivers, full day performance of complete system, cavity and aperture window test including influence from windeffects, control system tests, radiator system tests and special temperature measurements with infrared camera. The influence on performance of flux distribution depnding on concentrator alignment, and the optimum receiver operating criteria when balancing flux and temperatures on cooled receiver surface while avoiding flux on uncooled surfaces are also discussed.

  6. Testing of the United Stirling 4-95 solar Stirling engine on test bed concentrator

    Science.gov (United States)

    Nelving, H. G.

    1984-03-01

    The objectives with the testing, test set-ups, component designs, and the results of the testing of the solar Stirling engine in a parabolic dish system are presented. The most important tests are characterization of receivers, full day performance of complete system, cavity and aperture window test including influence from windeffects, control system tests, radiator system tests and special temperature measurements with infrared camera. The influence on performance of flux distribution depnding on concentrator alignment, and the optimum receiver operating criteria when balancing flux and temperatures on cooled receiver surface while avoiding flux on uncooled surfaces are also discussed.

  7. Two-Stage Over-the-Air (OTA Test Method for LTE MIMO Device Performance Evaluation

    Directory of Open Access Journals (Sweden)

    Ya Jing

    2012-01-01

    Full Text Available With MIMO technology being adopted by the wireless communication standards LTE and HSPA+, MIMO OTA research has attracted wide interest from both industry and academia. Parallel studies are underway in COST2100, CTIA, and 3GPP RAN WG4. The major test challenge for MIMO OTA is how to create a repeatable scenario which accurately reflects the MIMO antenna radiation performance in a realistic wireless propagation environment. Different MIMO OTA methods differ in the way to reproduce a specified MIMO channel model. This paper introduces a novel, flexible, and cost-effective method for measuring MIMO OTA using a two-stage approach. In the first stage, the antenna pattern is measured in an anechoic chamber using a nonintrusive approach, that is without cabled connections or modifying the device. In the second stage, the antenna pattern is convolved with the chosen channel model in a channel emulator to measure throughput using a cabled connection.

  8. IN VITRO TESTING – AN ESENTIAL METHOD FOR EVALUATING THE PERFORMANCE OF DENTAL MATERIALS AND DEVICES

    Directory of Open Access Journals (Sweden)

    Anca VIŢALARIU

    2015-06-01

    Full Text Available Dentistry is unique among biomaterials specialties as to the large variety of materials used, and nature of the challenges they must resist. Intra-oral service demands materials adapted to a warm and moist environment, resisting the attack of digestive acids and enzymes. The materials subjected to mechanical forces should preserve their strength, fatigue and wear characteristics, for accomplishing their function. The wide range of materials available for restorative dentistry demands knowledge of their relative strengths and trade-offs, and offers the opportunity for many interesting lines of research. The spectrum extensively ranges from elastic impression materials to extremely stiff metal and ceramic appliances, so that familiarity with a variety of mechanical testing situations is required from a well-rounded dental materials laboratory. Evaluating the mechanical and wear characteristics of dental restorative materials and analyzing the durability of adhesives is critical to the development of improved dental devices

  9. Are Current Accounts of Asian Economies Mean-reverting?: Nonlinear Unit Root Test Approach

    Directory of Open Access Journals (Sweden)

    Bonghan Kim

    2005-12-01

    Full Text Available This paper tests the mean reverting property of current account in the financial crisis-affected 5 counties of southeast Asia using nonlinear unit root tests of Park and shintani(2004. Our approach is based on the idea that a conventional unit root test has lower power in detecting the nonlinear mean reverting behavior if the current account follows a nonlinear mean reversion process. We obtained following empirical results. First, for the pre-crisis period (1981Q1-1996Q4, the current accounts of Indonesia, Malaysia and Philippines are mean-reverting but those of Korea and Thailand are not mean-reverting. Second, for the full sample period (1981Q1-2003Q4, the ADF test fails to reject the unit root of the current account in all countries except Philippines. However, unit root is rejected in favor of nonlinear mean reversion except Thailand. This nonlinear unit root test result implies that crisis-affected Asian countries except Thailand have sustainable paths of current accounts. Third, when the current accounts of East Asian countries are nonlinear mean-reverting, the mean reverting process can be well described by the ESTAR model, instead of the DTAR or DLSTAR model. The nonlinear unit root test results imply smooth nonlinear mean-reversion behaviors of East Asian current accounts. Finally, the shape of estimated impulse response functions becomes steeper as the size of shock increases, which is the very characteristic of the nonlinear process.

  10. Deformable microparticles with multiple functions for drug delivery and device testing

    Science.gov (United States)

    Thula, Taili T.

    Since the HIV epidemic of the 1990s, researchers have attempted to develop a red blood cell analog. Even though some of these substitutes are now in Phase III of clinical trials, their use is limited by side effects and short half-life in the human body. As a result, there is still a need for an effective erythrocyte analog with minimum immunogenic and side effects, so that it can be used for multiple applications. Finding new approaches to develop more efficient blood substitutes will not only bring valuable advances in the clinical approach, but also in the area of in vitro testing of medical devices. We examined the feasibility of creating a deformable multi-functional, biodegradable, biocompatible particle for applications in drug delivery and device testing. As a preliminary evaluation, we synthesized different types of microcapsules using natural and synthetic polymers, various cross-linking agents, and diverse manufacturing techniques. After fully characterizing of each system, we determined the most promising red blood cell analog in terms of deformability, stability and toxicity. We also examined the encapsulation and release of bovine serum albumin (BSA) within these deformable particles. After removal of cross-linkers, zinc- and copper-alginate microparticles surrounded by multiple polyelectrolyte layers of chitosan oligosaccharide and alginate were deformable and remained stable under physiological pressures applied by the micropipette technique. In addition, multiple coatings decreased toxicity of heavy-metal crosslinked particles. BSA encapsulation and release from chitosan-alginate microspheres were contingent on the crosslinker and number of polyelectrolyte coatings, respectively. Further rheological studies are needed to determine how closely these particles simulate the behavior of erythrocytes. Also, studies on the encapsulation and release of different proteins, including hemoglobin, are needed to establish the desired controlled release of

  11. Environmental assessment for device assembly facility operations, Nevada Test Site, Nye County, Nevada. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    The U.S. Department of Energy, Nevada Operations Office (DOE/NV), has prepared an environmental assessment (EA), (DOE/EA-0971), to evaluate the impacts of consolidating all nuclear explosive operations at the newly constructed Device Assembly Facility (DAF) in Area 6 of the Nevada Test Site. These operations generally include assembly, disassembly or modification, staging, transportation, testing, maintenance, repair, retrofit, and surveillance. Such operations have previously been conducted at the Nevada Test Site in older facilities located in Area 27. The DAF will provide enhanced capabilities in a state-of-the-art facility for the safe, secure, and efficient handling of high explosives in combination with special nuclear materials (plutonium and highly enriched uranium). Based on the information and analyses in the EA, DOE has determined that the proposed action would not constitute a major federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act of 1969 (42 U.S.C. 4321 et seq.). Therefore, an environmental impact statement is not required, and DOE is issuing this finding of no significant impact.

  12. Developing a press for static and dynamic testing of orthopedic devices and biological tissue

    Directory of Open Access Journals (Sweden)

    Arlex Leyton Virgen

    2010-05-01

    Full Text Available This paper describes designing and constructing a test machine having a 1,800 N capacity and maximum 3 Hz frequency which will be used in static and dynamic testing of biological tissues and orthopedic devices such as external fixers. It consists of an oc-tagonal base with 500 mm distance between faces and a crosshead which slides between two columns (useful 350 mm opening thus allowing changing the height (maximum 600 mm according to the size of the specimen to be tested. A ball screw actuator is mounted over the crosshead which transforms a servomotor’s rotating movement into a lineal movement (maximum 150 mm stroke. First validations indicated that the machine performed within the design parameters. This project shows that the techno-logy required for supporting research is possible in developing countries thereby avoiding dependence on foreign companies for supporting, maintaining and updating equipment. Some conditions were also produced for the evolution of mechanical engi-neering in Colombia.

  13. Astrodynamical Space Test of Relativity Using Optical Devices i (astrod i) — Mission Overview

    Science.gov (United States)

    Selig, Hanns; Lämmerzahl, Claus; Ni, Wei-Tou

    2013-01-01

    ASTROD I is the first planned space mission in a series of ASTROD missions for testing relativity in space using optical devices. The main aims are (i) to test general relativity with an improvement of three orders of magnitude compared to current results, (ii) to measure solar and solar system parameters with improved accuracy, (iii) to test the constancy of the gravitational constant and in general to get a deeper understanding of gravity. The first ideas for the ASTROD missions go back to the last century when new technologies in the area of laser physics and time measurement began to appear on the horizon. ASTROD is a mission concept that is supported by a broad international community covering the areas of space technology, fundamental physics, high performance laser and clock technology and drag-free control. While ASTROD I is a single-spacecraft concept that performs measurements with pulsed laser ranging between the spacecraft and earthbound laser ranging stations, ASTROD-GW is planned to be a three spacecraft mission with inter-spacecraft laser ranging. ASTROD-GW would be able to detect gravitational waves at frequencies below the eLISA/NGO bandwidth. As a third step Super-ASTROD with larger orbits could even probe primordial gravitational waves. This paper gives an overview on the basic principles especially for ASTROD I.

  14. Astrodynamical Space Test of Relativity using Optical Devices I (ASTROD I) - Mission Overview

    CERN Document Server

    Selig, Hanns; Ni, Wei-Tou

    2012-01-01

    ASTROD I is the first planned space mission in a series of ASTROD missions for testing relativity in space using optical devices. The main aims are: (i) to test General Relativity with an improvement of three orders of magnitude compared to current results, (ii) to measure solar and solar system parameters with improved accuracy, (iii) to test the constancy of the gravitational constant and in general to get a deeper understanding of gravity. The first ideas for the ASTROD missions go back to the last century when new technologies in the area of laser physics and time measurement began to appear on the horizon. ASTROD is a mission concept that is supported by a broad international community covering the areas of space technology, fundamental physics, high performance laser and clock technology and drag free control. While ASTROD I is a single-spacecraft concept that performes measurements with pulsed laser ranging between the spacecraft and earthbound laser ranging stations, ASTROD-GW is planned to be a three...

  15. An approach for assessment of water quality using semipermeable membrane devices (SPMDs) and bioindicator tests

    Science.gov (United States)

    Petty, J.D.; Jones, S.B.; Huckins, J.N.; Cranor, W.L.; Parris, J.T.; McTague, T.B.; Boyle, T.P.

    2000-01-01

    As an integral part of our continued development of water quality assessment approaches, we combined integrative sampling, instrumental analysis of widely occurring anthropogenic contaminants, and the application of a suite of bioindicator tests as a specific part of a broader survey of ecological conditions, species diversity, and habitat quality in the Santa Cruz River in Arizona, USA. Lipid-containing semipermeable membrane devices (SPMDs) were employed to sequester waterborne hydrophobic chemicals. Instrumental analysis and a suite of bioindicator tests were used to determine the presence and potential toxicological relevance of mixtures of bioavailable chemicals in two major water sources of the Santa Cruz River. The SPMDs were deployed at two sites; the effluent weir of the International Wastewater Treatment Plant (IWWTP) and the Nogales Wash. Both of these systems empty into the Santa Cruz River and the IWWTP effluent is a potential source of water for a constructed wetland complex. Analysis of the SPMD sample extracts revealed the presence of organochlorine pesticides (OCs), polychlorinated biphenyls (PCBs), and polycyclic aromatic hydrocarbons (PAHs). The bioindicator tests demonstrated increased liver enzyme activity, perturbation of neurotransmitter systems and potential endocrine disrupting effects (vitellogenin induction) in fish exposed to the extracts. With increasing global demands on limited water resources, the approach described herein provides an assessment paradigm applicable to determining the quality of water in a broad range of aquatic systems.

  16. Panel Unit Root Tests by Combining Dependent Values: A Comparative Study

    Directory of Open Access Journals (Sweden)

    Xuguang Sheng

    2011-01-01

    Full Text Available We conduct a systematic comparison of the performance of four commonly used value combination methods applied to panel unit root tests: the original Fisher test, the modified inverse normal method, Simes test, and the modified truncated product method (TPM. Our simulation results show that under cross-section dependence the original Fisher test is severely oversized, but the other three tests exhibit good size properties. Simes test is powerful when the total evidence against the joint null hypothesis is concentrated in one or very few of the tests being combined, but the modified inverse normal method and the modified TPM have good performance when evidence against the joint null is spread among more than a small fraction of the panel units. These differences are further illustrated through one empirical example on testing purchasing power parity using a panel of OECD quarterly real exchange rates.

  17. Unit root tests in time series, v.1 key concepts and problems

    CERN Document Server

    Patterson, Kerry, Professor

    2011-01-01

    Testing for a unit root is now an essential part of time series analysis. Indeed no time series study in economics, and other disciplines that use time series observations, can ignore the crucial issue of nonstationarity caused by a unit root. However, the literature on the topic is large and often technical, making it difficult to understand the key practical issues. This volume provides an accessible introduction and a critical overview of tests for a unit root in time series, with extensive practical examples and illustrations using simulation analysis. It presents the concepts that enable

  18. Testing iOS apps with HadoopUnit rapid distributed GUI testing

    CERN Document Server

    Tilley, Scott

    2014-01-01

    Smartphone users have come to expect high-quality apps. This has increased the importance of software testing in mobile software development. Unfortunately, testing apps-particularly the GUI-can be very time-consuming. Exercising every user interface element and verifying transitions between different views of the app under test quickly becomes problematic. For example, execution of iOS GUI test suites using Apple's UI Automation framework can take an hour or more if the app's interface is complicated. The longer it takes to run a test, the less frequently the test can be run, which in turn re

  19. Aerodynamic drag reduction tests on a full-scale tractor-trailer combination with several add-on devices

    Energy Technology Data Exchange (ETDEWEB)

    Montoya, L.C.; Steers, L.L.

    1974-12-01

    Aerodynamic drag tests were performed on a conventional cab-over-engine tractor with a 45-foot trailer and five commercially available or potentially available add-on devices using the coast-down method. The tests ranged in velocity from approximately 30 miles per hour to 65 miles per hour and included some flow visualization. A smooth, level runway at Edwards Air Force Base was used for the tests, and deceleration measurements were taken with both accelerometers and stopwatches. An evaluation of the drag reduction results obtained with each of the five add-on devices is presented.

  20. Testing objective measures of motor impairment in early Parkinson's disease: Feasibility study of an at-home testing device.

    Science.gov (United States)

    Goetz, Christopher G; Stebbins, Glenn T; Wolff, David; DeLeeuw, William; Bronte-Stewart, Helen; Elble, Rodger; Hallett, Mark; Nutt, John; Ramig, Lorraine; Sanger, Terence; Wu, Allan D; Kraus, Peter H; Blasucci, Lucia M; Shamim, Ejaz A; Sethi, Kapil D; Spielman, Jennifer; Kubota, Ken; Grove, Andrew S; Dishman, Eric; Taylor, C Barr

    2009-03-15

    We tested the feasibility of a computer based at-home testing device (AHTD) in early-stage, unmedicated Parkinson's disease (PD) patients over 6 months. We measured compliance, technical reliability, and patient satisfaction to weekly assessments of tremor, small and large muscle bradykinesia, speech, reaction/movement times, and complex motor control. relative to the UPDRS motor score. The AHTD is a 6.5'' x 10'' computerized assessment battery. Data are stored on a USB memory stick and sent by internet to a central data repository as encrypted data packets. Although not designed or powered to measure change, the study collected data to observe patterns relative to UPDRS motor scores. Fifty-two PD patients enrolled, and 50 completed the 6 month trial, 48 remaining without medication. Patients complied with 90.6% of weekly 30-minute assessments, and 98.5% of data packets were successfully transmitted and decrypted. On a 100-point scale, patient satisfaction with the program at study end was 87.2 (range: 80-100). UPDRS motor scores significantly worsened over 6 months, and trends for worsening over time occurred for alternating finger taps (P = 0.08), tremor (P = 0.06) and speech (P = 0.11). Change in tremor was a significant predictor of change in UPDRS (P = 0.047) and was detected in the first month of the study. This new computer-based technology offers a feasible format for assessing PD-related impairment from home. The high patient compliance and satisfaction suggest the feasibility of its incorporation into larger clinical trials, especially when travel is difficult and early changes or frequent data collection are considered important to document.

  1. Patch Testing for Evaluation of Hypersensitivity to Implanted Metal Devices: A Perspective From the American Contact Dermatitis Society.

    Science.gov (United States)

    Schalock, Peter C; Crawford, Glen; Nedorost, Susan; Scheinman, Pamela L; Atwater, Amber Reck; Mowad, Christen; Brod, Bruce; Ehrlich, Alison; Watsky, Kalman L; Sasseville, Denis; Silvestri, Dianne; Worobec, Sophie M; Elliott, John F; Honari, Golara; Powell, Douglas L; Taylor, James; DeKoven, Joel

    2016-01-01

    The American Contact Dermatitis Society recognizes the interest in the evaluation and management of metal hypersensitivity reactions. Given the paucity of robust evidence with which to guide our practices, we provide reasonable evidence and expert opinion-based guidelines for clinicians with regard to metal hypersensitivity reaction testing and patient management. Routine preoperative evaluation in individuals with no history of adverse cutaneous reactions to metals or history of previous implant-related adverse events is not necessary. Patients with a clear self-reported history of metal reactions should be evaluated by patch testing before device implant. Patch testing is only 1 element in the assessment of causation in those with postimplantation morbidity. Metal exposure from the implanted device can cause sensitization, but a positive metal test does not prove symptom causality. The decision to replace an implanted device must include an assessment of all clinical factors and a thorough risk-benefit analysis by the treating physician(s) and patient.

  2. Radiation Test Results on COTS and non-COTS Electronic Devices for NASA-JSC Space Flight Projects

    Science.gov (United States)

    Allums, Kimberly K.; O'Neill, P. M.; Reddell, B. D.; Nguyen, K. V.; Bailey, C. R.

    2012-01-01

    This presentation reports the results of recent proton and heavy ion Single Event Effect (SEE) testing on a variety of COTS and non-COTs electronic devices and assemblies tested for the Space Shuttle, International Space Station (ISS) and Multi-Purpose Crew Vehicle (MPCV).

  3. The viability of hearing protection device fit-testing at navy and marine corps accession points

    Directory of Open Access Journals (Sweden)

    Jeremy Federman

    2016-01-01

    Full Text Available Introduction: The viability of hearing protection device (HPD verification (i.e., fit-testing on a large scale was investigated to address this gap in a military accession environment. Materials and Methods: Personal Attenuation Ratings (PARs following self-fitted (SELF-Fit HPDs were acquired from 320 US Marine Corps training recruits (87.5% male, 12.5% female across four test protocols (1-, 3-, 5-, and 7- frequency. SELF-Fit failures received follow-up to assess potential causes. Follow-up PARs were acquired (Experimenter fit [EXP-Fit], followed by Subject re-fit [SUB Re-Fit]. EXP-Fit was intended to provide a perception (dubbed “ear canal muscle memory” of what a correctly fitted HPD should feel like. SUB Re-Fit was completed following EXP-Fit to determine whether a training recruit could duplicate EXP-Fit on her/his own without assistance. Results: A one-way analysis of variance (ANOVA (N = 320 showed that SELF-Fit means differed significantly between protocols (P 60% pass rates. Results showed that once recruits experienced how HPDs should feel when inserted correctly, they were able to properly replicate the procedure with similar results to the expert fit suggesting “ear canal muscle memory” may be a viable training strategy concomitant with HPD verification. Fit-test duration was also measured to examine the tradeoff between results accuracy and time required to complete each protocol. Discussion: Results from this study showed the critical importance of initial selection and fitting of HPDs followed by verification (i.e., fit-testing at Navy and Marine Corps accession points. Achieving adequate protection from an HPD is fundamentally dependent on obtaining proper fit of the issued HPD as well as the quality of training recruits receive regarding HPD use.

  4. Rotor scale model tests for power conversion unit of GT-MHR

    Energy Technology Data Exchange (ETDEWEB)

    Baxi, C.B., E-mail: baxicb1130@hotmail.com [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States); Telengator, A.; Razvi, J. [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States)

    2012-10-15

    The gas turbine modular helium reactor (GT-MHR) combines a modular high-temperature gas-cooled reactor (HTGR) nuclear heat source with a closed Brayton gas-turbine cycle power conversion unit (PCU) for thermal to electric energy conversion. The PCU has a vertical orientation and is supported on electromagnetic bearings (EMB). The rotor scale model (RSM) tests are intended to directly model the control of EMB and rotor dynamic characteristics of the full-scale GT-MHR turbo-machine (TM). The objectives of the RSM tests are to: Bullet Confirm the EMB control system design for the GT-MHR turbo machine over the full-range of operation. Bullet Confirm the redundancy and on-line maintainability features that have been specified for the EMBs. Bullet Provide a benchmark for validation of analytical tools that will be used for independent analyses of the EMB subsystem design. Bullet Provide experience with the installation, operation and maintenance of EMBs supporting multiple rotors with flexible couplings. As with the full-scale TM, the RSM incorporates two rotors that are joined by a flexible coupling. Each of the rotors is supported on one axial and two radial EMBs. Additional devices, similar in concept to radial EMBs, are installed to simulate magnetic and/or mechanical forces representing those that would be seen by the exciter, generator, compressors and turbine. Overall, the lengths of the RSM rotor is about 1/3rd that of the full-scale TM, while the diameters are approximately 1/5th scale. The design and sizing of the rotor is such that the number and values of critical speeds in the RSM are the same as in the full-scale TM. The EMBs are designed such that their response to rotor dynamic forces is representative of the full-scale TM. The fabrication and assembly of the RSM was completed at the end of 2008. All start up adjustments were finished in December 2009. To-date the generator rotor has been supported in the EMBs and rotated up to 1800 rpm. Final tests are

  5. Calibration of an automated California mastitis test with focus on the device-dependent variation.

    Science.gov (United States)

    Neitzel, Anne-Christin; Stamer, Eckhard; Junge, Wolfgang; Thaller, Georg

    2014-01-01

    The aim of the paper was to estimate the accuracy of the metrology of an installed indirect on-line sensor system based on the automated California Mastitis Test (CMT) with focus on the prior established device-dependent variation. A sensor calibration was implemented. Therefore, seven sensors were tested with similar trials on the dairy research farm Karkendamm (Germany) on two days in July 2011 and January 2012. Thereby, 18 mixed milk samples from serial dilutions were fourfold recorded at every sensor. For the validation, independent sensor records with corresponding lab somatic cell score records (LSCS) in the period between both trials were used (n = 1,357). From these records for each sensor a polynomial regression function was calculated. The predicted SCS (PSCS) was obtained for each sensor with the previously determined regression coefficients. Pearson correlation coefficients between PSCS and LSCS were established for each sensor and ranged between r = 0.57 and r = 0.67. Comparing the results with the correlation coefficients between the on-line SCS (OSCS) and the LSCS (r = 0.20 to 0.57) for every sensor, the calibration showed the tendency to improve the installed sensor system.

  6. Three-dimensional mapping of equiprobable hydrostratigraphic units at the Frenchman Flat Corrective Action Unit, Nevada Test Site

    Energy Technology Data Exchange (ETDEWEB)

    Shirley, C.; Pohlmann, K.; Andricevic, R.

    1996-09-01

    Geological and geophysical data are used with the sequential indicator simulation algorithm of Gomez-Hernandez and Srivastava to produce multiple, equiprobable, three-dimensional maps of informal hydrostratigraphic units at the Frenchman Flat Corrective Action Unit, Nevada Test Site. The upper 50 percent of the Tertiary volcanic lithostratigraphic column comprises the study volume. Semivariograms are modeled from indicator-transformed geophysical tool signals. Each equiprobable study volume is subdivided into discrete classes using the ISIM3D implementation of the sequential indicator simulation algorithm. Hydraulic conductivity is assigned within each class using the sequential Gaussian simulation method of Deutsch and Journel. The resulting maps show the contiguity of high and low hydraulic conductivity regions.

  7. New multi-country evidence on purchasing power parity: multivariate unit root test results

    NARCIS (Netherlands)

    J.J.J. Groen (Jan)

    2000-01-01

    textabstractIn this paper a likelihood-based multivariate unit root testing framework is utilized to test whether the real exchange rates of G10 countries are non-stationary. The framework uses a likelihood ratio statistic which combines the information across all involved countries while retaining

  8. Predicting performance and situation awareness of robot operators in complex situations by unit task tests

    NARCIS (Netherlands)

    Mioch, T.; Smets, N.J.J.M.; Neerincx, M.A.

    2012-01-01

    Human-in-the-loop field tests of human-robot operations in high-demand situations provide serious constraints with respect to costs and control. A set of relatively simple unit tasks might be used to do part of the testing and to establish a benchmark for human-robot performance and situation awaren

  9. Test Format and the Variation of Gender Achievement Gaps within the United States

    Science.gov (United States)

    Reardon, Sean; Fahle, Erin; Kalogrides, Demetra; Podolsky, Anne; Zarate, Rosalia

    2016-01-01

    Prior research demonstrates the existence of gender achievement gaps and the variation in the magnitude of these gaps across states. This paper characterizes the extent to which the variation of gender achievement gaps on standardized tests across the United States can be explained by differing state accountability test formats. A comprehensive…

  10. Connecting Girls and Science: A Feminist Teacher Research Study of a High School Prenatal Testing Unit.

    Science.gov (United States)

    Howes, Elaine Virginia

    1998-01-01

    Explores how a dozen high school girls express their relationship to and understanding of prenatal testing and its possible place in their lives and the lives of others in the context of a short unit on prenatal testing in a semester-long genetics course. Contains 57 references. (DDR)

  11. Predicting performance and situation awareness of robot operators in complex situations by unit task tests

    NARCIS (Netherlands)

    Mioch, T.; Smets, N.J.J.M.; Neerincx, M.A.

    2012-01-01

    Human-in-the-loop field tests of human-robot operations in high-demand situations provide serious constraints with respect to costs and control. A set of relatively simple unit tasks might be used to do part of the testing and to establish a benchmark for human-robot performance and situation awaren

  12. Intellectual Maturity of Children as Measured by the Goodenough-Harris Drawing Test: United States.

    Science.gov (United States)

    Health Services and Mental Health Administration (DHEW), Bethesda, MD.

    Information is reported on the intellectual maturity of children 6 through 11 years of age in the United States as estimated from the 1963 Goodenough-Harris Drawing Test data obtained in the Health Examination Survey of 1963-1965. Consideration is limited in this first report of a series of reports on these test findings to age and sex…

  13. Factors determining patients’ intentions to use point-of-care testing medical devices for self-monitoring: the case of international normalized ratio self-testing

    Science.gov (United States)

    Shah, Syed Ghulam Sarwar; Barnett, Julie; Kuljis, Jasna; Hone, Kate; Kaczmarski, Richard

    2013-01-01

    Purpose To identify factors that determine patients’ intentions to use point-of-care medical devices, ie, portable coagulometer devices for self-testing of the international normalized ratio (INR) required for ongoing monitoring of blood-coagulation intensity among patients on long-term oral anticoagulation therapy with vitamin K antagonists, eg, warfarin. Methods A cross-sectional study that applied the technology-acceptance model through a self-completed questionnaire, which was administered to a convenience sample of 125 outpatients attending outpatient anticoagulation services at a district general hospital in London, UK. Data were analyzed using descriptive statistics, factor analyses, and structural equation modeling. Results The participants were mainly male (64%) and aged ≥ 71 years (60%). All these patients were attending the hospital outpatient anticoagulation clinic for INR testing; only two patients were currently using INR self-testing, 84% of patients had no knowledge about INR self-testing using a portable coagulometer device, and 96% of patients were never offered the option of the INR self-testing. A significant structural equation model explaining 79% of the variance in patients’ intentions to use INR self-testing was observed. The significant predictors that directly affected patients’ intention to use INR self-testing were the perception of technology (β = 0.92, P < 0.001), trust in doctor (β = −0.24, P = 0.028), and affordability (β = 0.15, P = 0.016). In addition, the perception of technology was significantly affected by trust in doctor (β = 0.43, P = 0.002), age (β = −0.32, P < 0.001), and affordability (β = 0.23, P = 0.013); thereby, the intention to use INR self-testing was indirectly affected by trust in doctor (β = 0.40), age (β = −0.29), and affordability (β = 0.21) via the perception of technology. Conclusion Patients’ intentions to use portable coagulometers for INR self-testing are affected by patients

  14. Examining the Islamic stock market efficiency: Evidence from nonlinear ESTAR unit root tests

    Directory of Open Access Journals (Sweden)

    Rahmat Heru Setianto

    2015-04-01

    Full Text Available This paper empirically examines the efficient market hypothesis (EMH in the Islamic stock market namely Jakarta Islamic Index by emphasizing on the random walk behavior and nonlinearity. In the first step, we employ Brock et al. (1996 test to examine the presence of nonlinear behavior in Jakarta Islamic Index. The evidence of nonlinear behavior in the indices, motivate us to use nonlinear ESTAR unit root test procedure recently developed by Kapetanios et al. (2003 and Kruse (2011. The nonlinear unit root test procedure fail to rejects the null hypothesis of unit root for the indices, suggesting that Jakarta Islamic Index characterized by random walk process supporting the theory of efficient market hypothesis. In addition, Lumsdaine and Papel (LP test identified significant structural breaks in the index series.

  15. 77 FR 60481 - Design, Inspection, and Testing Criteria for Air Filtration and Adsorption Units of Post-Accident...

    Science.gov (United States)

    2012-10-03

    ... COMMISSION Design, Inspection, and Testing Criteria for Air Filtration and Adsorption Units of Post-Accident..., and Testing Criteria for Air Filtration and Adsorption Units of Post-accident Engineered-Safety... design, inspection, and testing of air filtration and iodine adsorption units of...

  16. 77 FR 50722 - Software Unit Testing for Digital Computer Software Used in Safety Systems of Nuclear Power Plants

    Science.gov (United States)

    2012-08-22

    ... COMMISSION Software Unit Testing for Digital Computer Software Used in Safety Systems of Nuclear Power Plants... regulatory guide (DG), DG-1208, ``Software Unit Testing for Digital Computer Software used in Safety Systems... entitled ``Software Unit Testing for Digital Computer Software Used in Safety Systems of Nuclear...

  17. Test of a device for accelerated ageing of polymeric material in high concentrated sunlight at the DLR solar furnace

    Energy Technology Data Exchange (ETDEWEB)

    Witzke, A.; Neumann, A.; Kaluza, J. [German Aerospace Center (DLR), Solar Energy Technology, Cologne (Germany); Demuth, M.; Ritterskamp, P. [Max-Planck-Inst. fuer Strahlenchemie, Muelheim a.d.R. (Germany)

    2001-07-01

    Within this study the design and first tests of a device for accelerated ageing with high concentrated sunlight have been described. Firstly, the device was designed for testing samples of lacquer for the car industry. It is based on two points: first, the photochemical effect that the ageing of polymers is mainly initiated by the UV solar radiation and, second, on the idea to accelerate the ageing process by increasing the UV radiation dose. Therefore the concentrated sunlight at the DLR Solar Furnace is filtered by a cold-mirror that reflects the radiation with a wavelength below 450 nm onto the samples. The samples are fixed in a chamber where they can simultaneously be wetted by a spraying device. The first tests show that this device enables us to radiate the relevant samples with a high UV radiation intensity without overheating them. During one day irradiation at the DLR Solar Furnace in March 2001 we reach an UV radiation dose which is about sixteen times higher than the dose after 24 hours irradiation in common used weathering devices. Further tests at the DLR Solar Furnace have to examine in what way this increased radiation dose leads to a high accelerated ageing of the polymeric material. (orig.)

  18. Complex plasma experimental device – A test bed for studying dust vortices and other collective phenomena

    Indian Academy of Sciences (India)

    MANJIT KAUR; SAYAK BOSE; P K CHATTOPADHYAY; J GHOSH; Y C SAXENA

    2016-12-01

    A typical device for carrying out sophisticated and complex dusty plasma experiments is designed, fabricated and made operational at the Institute for Plasma Research, India. The device is named as complex plasma experimental device (CPED). The main aim of this multipurpose machine is to study the formation and behaviour of dust vortices in the absence of external magnetic field under the effect of various plasma parameters. Further, the device is equipped with advanced imaging diagnostics for studying many other interesting phenomena such as dust oscillations, three-dimensional crystalline structures, dust rotation, etc. The device is quite flexible to accommodate many innovative experiments. Detailed design of the device, its diagnostics capabilities and theadvanced image analysis techniques are presented in this paper.

  19. Accounting the mechanical resistance of testing device for straight-flow branch pipe in the transverse direction

    Science.gov (United States)

    Sitnikov, D. V.; Klishin, S. V.; Zubarev, A. V.; Shvarts, A. A.

    2017-06-01

    The flexible inserts as a rubber-cord branch pipe are used to reduce the vibrations distributed from units of a hydraulic system through the pipelines. The device with completely rigid elements is used for the experimental determination of the stiffness characteristics of the branch pipes that determine their anti-vibration properties. In the paper the study of the mechanical resistances of an experimental device construction is carried out by method of the harmonic analysis in a frequency range of 1 Hz to 1000 Hz. Then these mechanical resistances are compared with the mechanical resistance of the branch pipe with diameter 100 mm obtained experimentally. It is found as a result it is necessary to take into account the value of the device mechanical resistance when the stiffness characteristics of the rubber-cord branch pipes with diameter 100 mm in the transverse direction at frequencies above 735 Hz are determined experimentally.

  20. Development and testing of INSPIRE themes Addresses (AD and Administrative Units (AU managed by COSMC

    Directory of Open Access Journals (Sweden)

    Michal Med

    2013-12-01

    Full Text Available Main content of this article is to describe implementing INSPIRE themes Addresses and Administrative Units in Czech Republic. Themes were implemented by Czech Office for Surveying, Mapping and Cadastre. Implementation contains developing GML files with data and designing its structure, developing and testing of INSPIRE services and preparing metadata for data and services. Besides harmonised INSPIRE themes COSMC manages also non-harmonised themes Cadastral map (KM and Units eXtended (UX.

  1. Assembly and test results of the AOF laser guide star units at ESO

    Science.gov (United States)

    Hackenberg, W.; Bonaccini Calia, D.; Buzzoni, B.; Comin, M.; Dupuy, C.; Gago, F.; Guidolin, I. M.; Guzman, R.; Holzloehner, R.; Kern, L.; Kirchbauer, J.-.; Lewis, S.; Lizon, J.-.; McLay, S.; Pfrommer, T.; Quattri, M.; Quentin, J.; Ridings, R.

    2014-08-01

    The Four Laser Guide Star Facility (4LGSF) is part of the ESO Adaptive Optics Facility, in which one of the VLT telescopes, UT4, is transformed in an adaptive telescope-equipped with a deformable secondary mirror, two adaptive optics systems at the Nasmyth focii and four sodium laser guide star modular units. In this paper we present the design, the assembly and validation test performed so far in Europe on the first laser guide star unit.

  2. Study and Test of Cold Storage Heat Recovery Heat Pump Coupled Solar Drying Device

    OpenAIRE

    Min Li; Xiao-Qiang Jiang; Bao-Chuan Wu

    2013-01-01

    In this study, we design the recovery of a heat pump combined solar drying device. Then, with this device, drying experiments of aquatic product, tilapia, were conducted, indicating that the newly designed device functions are well in temperature adjusting and controlling performance and showing that drying time is closely related to energy consumption and drying conditions. Heat recovery heat pump combined solar energy drier can improve the drying quality of aquatic products, but also can gr...

  3. Development and Testing of a Device to Increase the Level of Automation of a Conventional Milking Parlor through Vocal Commands

    Directory of Open Access Journals (Sweden)

    Mauro Zaninelli

    2017-01-01

    Full Text Available A portable wireless device with a “vocal commands” feature for activating the mechanical milking phase in conventional milking parlors was developed and tested to increase the level of automation in the milking procedures. The device was tested in the laboratory and in a milking parlor. Four professional milkers participated in the experiment. Before the start of the tests, a set of acoustic models with speaker-dependent commands defined for the project was acquired for each milker using a dedicated “milker training procedure”. Two experimental sessions were performed by each milker, with one session in the laboratory and a subsequent session in the milking parlor. The device performance was evaluated based on the accuracy demonstrated in the vocal command recognition task and rated using the word recognition rate (WRR. The data were expressed as %WRR and grouped based on the different cases evaluated. Mixed effects logistic regression modeling was used to evaluate the association between the %WRR and explanatory variables. The results indicated significant effects due to the location where the tests were performed. Higher values of the %WRR were found for tests performed in the laboratory, whereas lower values were found for tests performed in the milking parlor (due to the presence of background noise. Nevertheless, the general performance level achieved by the device was sufficient for increasing the automation level of conventional milking parlors.

  4. Study and Test of Cold Storage Heat Recovery Heat Pump Coupled Solar Drying Device

    Directory of Open Access Journals (Sweden)

    Min Li

    2013-05-01

    Full Text Available In this study, we design the recovery of a heat pump combined solar drying device. Then, with this device, drying experiments of aquatic product, tilapia, were conducted, indicating that the newly designed device functions are well in temperature adjusting and controlling performance and showing that drying time is closely related to energy consumption and drying conditions. Heat recovery heat pump combined solar energy drier can improve the drying quality of aquatic products, but also can greatly reduce the drying energy consumption, which provides theoretical support to the design and processing of heat recovery heat pump of refrigeration system coupled solar drying device.

  5. Estimation of the two-dimensional presampled modulation transfer function of digital radiography devices using one-dimensional test objects.

    Science.gov (United States)

    Wells, Jered R; Dobbins, James T

    2012-10-01

    The modulation transfer function (MTF) of medical imaging devices is commonly reported in the form of orthogonal one-dimensional (1D) measurements made near the vertical and horizontal axes with a slit or edge test device. A more complete description is found by measuring the two-dimensional (2D) MTF. Some 2D test devices have been proposed, but there are some issues associated with their use: (1) they are not generally available; (2) they may require many images; (3) the results may have diminished accuracy; and (4) their implementation may be particularly cumbersome. This current work proposes the application of commonly available 1D test devices for practical and accurate estimation of the 2D presampled MTF of digital imaging systems. Theory was developed and applied to ensure adequate fine sampling of the system line spread function for 1D test devices at orientations other than approximately vertical and horizontal. Methods were also derived and tested for slit nonuniformity correction at arbitrary angle. Techniques were validated with experimental measurements at ten angles using an edge test object and three angles using a slit test device on an indirect-detection flat-panel system [GE Revolution XQ∕i (GE Healthcare, Waukesha, WI)]. The 2D MTF was estimated through a simple surface fit with interpolation based on Delaunay triangulation of the 1D edge-based MTF measurements. Validation by synthesis was also performed with simulated images from a hypothetical direct-detection flat-panel device. The 2D MTF derived from physical measurements yielded an average relative precision error of 0.26% for frequencies below the cutoff (2.5 mm(-1)) and approximate circular symmetry at frequencies below 4 mm(-1). While slit analysis generally agreed with the results of edge analysis, the two showed subtle differences at frequencies above 4 mm(-1). Slit measurement near 45° revealed radial asymmetry in the MTF resulting from the square pixel aperture (0.2 mm × 0

  6. Fat Tail Model for Simulating Test Systems in Multiperiod Unit Commitment

    Directory of Open Access Journals (Sweden)

    J. A. Marmolejo

    2015-01-01

    Full Text Available This paper describes the use of Chambers-Mallows-Stuck method for simulating stable random variables in the generation of test systems for economic analysis in power systems. A study that focused on generating test electrical systems through fat tail model for unit commitment problem in electrical power systems is presented. Usually, the instances of test systems in Unit Commitment are generated using normal distribution, but in this work, simulations data are based on a new method. For simulating, we used three original systems to obtain the demand behavior and thermal production costs. The estimation of stable parameters for the simulation of stable random variables was based on three generally accepted methods: (a regression, (b quantiles, and (c maximum likelihood, choosing one that has the best fit of the tails of the distribution. Numerical results illustrate the applicability of the proposed method by solving several unit commitment problems.

  7. Novel device to sample the esophageal microbiome--the esophageal string test.

    Directory of Open Access Journals (Sweden)

    Sophie A Fillon

    Full Text Available A growing number of studies implicate the microbiome in the pathogenesis of intestinal inflammation. Previous work has shown that adults with esophagitis related to gastroesophageal reflux disease have altered esophageal microbiota compared to those who do not have esophagitis. In these studies, sampling of the esophageal microbiome was accomplished by isolating DNA from esophageal biopsies obtained at the time of upper endoscopy. The aim of the current study was to identify the esophageal microbiome in pediatric individuals with normal esophageal mucosa using a minimally invasive, capsule-based string technology, the Enterotest™. We used the proximal segment of the Enterotest string to sample the esophagus, and term this the "Esophageal String Test" (EST. We hypothesized that the less invasive EST would capture mucosal adherent bacteria present in the esophagus in a similar fashion as mucosal biopsy. EST samples and mucosal biopsies were collected from children with no esophageal inflammation (n = 15 and their microbiome composition determined by 16S rRNA gene sequencing. Microbiota from esophageal biopsies and ESTs produced nearly identical profiles of bacterial genera and were different from the bacterial contents of samples collected from the nasal and oral cavity. We conclude that the minimally invasive EST can serve as a useful device for study of the esophageal microbiome.

  8. Radiation Hardness tests with neutron flux on different Silicon photomultiplier devices

    Science.gov (United States)

    Cattaneo, P. W.; Cervi, T.; Menegolli, A.; Oddone, M.; Prata, M.; Prata, M. C.; Rossella, M.

    2017-07-01

    Radiation hardness is an important requirement for solid state readout devices operating in high radiation environments common in particle physics experiments. The MEG II experiment, at PSI, Switzerland, investigates the forbidden decay μ+ → e+ γ. Exploiting the most intense muon beam of the world. A significant flux of non-thermal neutrons (kinetic energy Ek>= 0.5 MeV) is present in the experimental hall produced along the beam-line and in the hall itself. We present the effects of neutron fluxes comparable to the MEG II expected doses on several Silicon Photomultiplier (SiPMs). The tested models are: AdvanSiD ASD-NUV3S-P50 (used in MEG II experiment), AdvanSiD ASD-NUV3S-P40, AdvanSiD ASD-RGB3S-P40, Hamamatsu and Excelitas C30742-33-050-X. The neutron source is the thermal Sub-critical Multiplication complex (SM1) moderated with water, located at the University of Pavia (Italy). We report the change of SiPMs most important electric parameters: dark current, dark pulse frequency, gain, direct bias resistance, as a function of the integrated neutron fluency.

  9. Medical chilling device designed for hypothermic hydration graft storage system: Design, thermohydrodynamic modeling, and preliminary testing

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Jung Hwan [Hongik University, Seoul (Korea, Republic of)

    2015-02-15

    Hypothermic hydration graft storage is essential to reduce the metabolic demand of cells in vitro. The alleviated metabolic demands reduce the emergence rate of anaerobic metabolism generating adenosine triphosphate (ATP) energy that creates free radicals. The cessive free radicals can damage cells and tissues due to their highly oxidative power with molecules. Current cooling systems such as a conventional air cooling system and an ice pack system are inappropriate for chilling cell tissues in vitro because of inconvenience in use and inconsistent temperature sustainability caused by large size and progressive melting, respectively. Here, we develop a medical chilling device (MCD) for hypothermic hydration graft storage based on thermo-hydrodynamic modeling and thermal electric cooling technology. Our analysis of obtained hydrodynamic thermal behavior of the MCD revealed that the hypothermic condition of 4 .deg. C was continuously maintained, which increased the survival rates of cells in vitro test by reduced free radicals. The validated performance of the MCD promises future development of an optimal hypothermic hydration graft storage system designed for clinical use.

  10. Durability test device for MR fluids with permanent magnet and V-shaped groove

    Science.gov (United States)

    Abe, Isao; Kikuchi, Takehito; Noma, Junichi

    2017-05-01

    Magnetorheological fluids (MRFs) are functional fluids whose viscosity changes when magnetic fields are applied. Therefore, these fluids are used in force and torque controllable devices. However, particle sedimentation is one of the drawbacks of conventional MRFs. To solve this problem, Kurimoto Co. Ltd developed a new fluid with sub-micron order Fe particles and a silicone-based solvent known as NanoMRF. The particle distributions of this material are stable over several months. However, its durability has not yet been fully discussed. Therefore, we developed new equipment to test endurance and examined the durability of the magnetorheological effect of the NanoMRF as well as a commercially available MRF. Our results show that the durability of the fluids was affected by the stability of the solvent. In particular, the durability is drastically improved when the solvent is supplemented by the peripheral sealing oil. The oxidation of particles is remarkably varied by the kind of solvent as well as the stability of the oxidation film on the surface of the particles. The energy of the collapse and reproduction of the particles was used not only to generate friction among the particles but also to decompose the solvent molecules.

  11. Space Station and Shuttle Payloads: Rack Insertion Device Pneumatic Assembly Setup and Test

    Science.gov (United States)

    Conde, Nathan

    2007-01-01

    As part of my KSC summer internship, I was given the very cool task of writing a test preparation sheet (TPS). A TPS is a set of instructions for certain procedures or tasks, and serves as the documentation for the tasks. TPSs guide task leaders and technicians throughout the work procedures, safely, informing them of what steps will be hazardous, what precautions must be taken, and what to do in the case of an accident or emergency. I was placed in Boeing's Resupply & Return Division (R&R). R&R is responsible for sending up food and supplies to the International Space Station (ISS) with the use of three Italian Multi Purpose Logistics Modules - Leonardo, Donatello, and Raffaello. The supplies are loaded into Resupply Stowage Racks (RSRs) or Resupply Stowage Platforms (RSPs) (though, both are usually referred to as racks), depending on their size and shape. These racks are loaded into the modules with the help of a specialized crane known as the Rack Insertion Device (RID). The RID rests on four pneumatic air jacks, these allow for an operator to raise or lower the RID. The pneumatic air system supplies the air jacks with the necessary air pressure required to lift the RID.

  12. Final report on the in situ testing of electrical components and devices at TMI-2

    Energy Technology Data Exchange (ETDEWEB)

    Soberano, F T

    1984-06-01

    A total of 88 electrical components and devices were in situ tested. Of these, 11 totally failed and 21 suffered degradation that varied from mild to severe. The equipment that failed or incurred severe degradation was located in areas of known environmental extremes. Several motor operated valves in the Reactor Building basement failed because of submersion in water. Others severely degraded from contamination tracking, resulting in the alteration of their circuit electrical characteristics - a circumstance that could compromise their designed function. One backup oil lift pump motor for a reactor coolant pump motor, although located well above the Reactor Building basement high water mark, failed because of a break in its armature and field circuits; this failure was surmised to be a result of corrosion. The limit switch of a Class 1E solenoid valve likewise failed due to moisture intrusion. Components that noticeably degraded exhibited anomalies, likely due to the incursion of moisture, that varied from high capacitance to increased circuit resistance. The effect of the other degenerating conditions that existed during the accident, such as high temperature, high radiation levels, and the hydrogen burn, could not be evaluated individually or synergistically.

  13. 3D-FBK Pixel sensors: recent beam tests results with irradiated devices

    CERN Document Server

    Micelli, A; Sandaker, H; Stugu, B; Barbero, M; Hugging, F; Karagounis, M; Kostyukhin, V; Kruger, H; Tsung, J W; Wermes, N; Capua, M; Fazio, S; Mastroberardino, A; Susinno, G; Gallrapp, C; Di Girolamo, B; Dobos, D; La Rosa, A; Pernegger, H; Roe, S; Slavicek, T; Pospisil, S; Jakobs, K; Kohler, M; Parzefall, U; Darbo, G; Gariano, G; Gemme, C; Rovani, A; Ruscino, E; Butter, C; Bates, R; Oshea, V; Parker, S; Cavalli-Sforza, M; Grinstein, S; Korokolov, I; Pradilla, C; Einsweiler, K; Garcia-Sciveres, M; Borri, M; Da Via, C; Freestone, J; Kolya, S; Lai, C H; Nellist, C; Pater, J; Thompson, R; Watts, S J; Hoeferkamp, M; Seidel, S; Bolle, E; Gjersdal, H; Sjobaek, K N; Stapnes, S; Rohne, O; Su, D; Young, C; Hansson, P; Grenier, P; Hasi, J; Kenney, C; Kocian, M; Jackson, P; Silverstein, D; Davetak, H; DeWilde, B; Tsybychev, D; Dalla Betta, G F; Gabos, P; Povoli, M; Cobal, M; Giordani, M P; Selmi, L; Cristofoli, A; Esseni, D; Palestri, P; Fleta, C; Lozano, M; Pellegrini, G; Boscardin, M; Bagolini, A; Piemonte, C; Ronchin, S; Zorzi, N; Hansen, T E; Hansen, T; Kok, A; Lietaer, N; Kalliopuska, J; Oja, A

    2011-01-01

    The Pixel detector is the innermost part of the ATLAS experiment tracking device at the Large Hadron Collider (LHC), and plays a key role in the reconstruction of the primary and secondary vertices of short-lived particles. To cope with the high level of radiation produced during the collider operation, it is planned to add to the present three layers of silicon pixel sensors which constitute the Pixel Detector, an additional layer (Insertable B-Layer, or IBL) of sensors. 3D silicon sensors are one of the technologies which are under study for the IBL. 3D silicon technology is an innovative combination of very-large-scale integration (VLSI) and Micro-Electro-Mechanical-Systems (MEMS) where electrodes are fabricated inside the silicon bulk instead of being implanted on the wafer surfaces. 3D sensors, with electrodes fully or partially penetrating the silicon substrate, are currently fabricated at different processing facilities in Europe and USA. This paper reports on the 2010 June beam test results for irradi...

  14. Test Results From a Direct Drive Gas Reactor Simulator Coupled to a Brayton Power Conversion Unit

    Science.gov (United States)

    Hervol, David S.; Briggs, Maxwell H.; Owen, Albert K.; Bragg-Sitton, Shannon M.

    2009-01-01

    The Brayton Power Conversion Unit (BPCU) located at NASA Glenn Research Center (GRC) in Cleveland, OH is a closed cycle system incorporating a turboaltemator, recuperator, and gas cooler connected by gas ducts to an external gas heater. For this series of tests, the BPCU was modified by replacing the gas heater with the Direct Drive Gas heater or DOG. The DOG uses electric resistance heaters to simulate a fast spectrum nuclear reactor similar to those proposed for space power applications. The combined system thermal transient behavior was the focus of these tests. The BPCU was operated at various steady state points. At each point it was subjected to transient changes involving shaft rotational speed or DOG electrical input. This paper outlines the changes made to the test unit and describes the testing that took place along with the test results.

  15. Soil washing physical separations test procedure - 300-FF-1 operable unit

    Energy Technology Data Exchange (ETDEWEB)

    Belden, R.D.

    1993-10-08

    This procedure provides the operations approach, a field sampling plan, and laboratory procedures for a soil washing test to be conducted by Alternative Remedial Technologies, Inc. (ART) in the 300-FF-1 area at the Hanford site. The {open_quotes}Quality Assurance Project Plan for the Soil Washing Physical Separations Test, 300-FF-1 Operable Unit,{close_quotes} Hanford, Washington, Alternative Remedial Technologies, Inc., February 1994 (QAPP) is provided in a separate document that presents the procedural and organizational guidelines for this test. This document describes specifications, responsibilities, and general procedures to be followed to conduct physical separation soil treatability tests in the North Process Pond of the 300-FF-1 Operable Unit (OU) at the Hanford Site. These procedures are based on the {open_quotes}300-FF-1 Physical Separations CERCLA Treatability Test Plan, DOE/RL 92-2l,{close_quotes} (DOE-RL 1993).

  16. Behavioral analysis during the forced swimming test using a joystick device.

    Science.gov (United States)

    Gersner, Roman; Dar, Dalit E; Shabat-Simon, Maytal; Zangen, Abraham

    2005-04-30

    The behavioral test described by Porsolt in 1977 for screening potential antidepressant drugs is extensively used both in basic research and in the pharmaceutical industry. The measured behavior is the immobility time during the swimming test (preformed in rodents), which decreases upon acute antidepressant treatment. Several research groups have suggested some modifications on the original Porsolt paradigm and its analysis. Nevertheless, there are still inaccuracies resulting from either undefined intermediate behaviors or from considering the movement of the whole body as one unit without analyzing the motion of the limbs. Herein, we propose a novel and simple scoring method, based on continuous measurement of the limbs motion, using a joystick, a computer screen and simple software. We validated the method, using antidepressant drugs and studied examples of false positives and false negatives of the traditional Porsolt paradigm. The proposed method is easy to use, it accounts for all range of movements and the analysis is relatively fast. Moreover, the results obtained using this analysis method show a normal Gaussian distribution in a population of rats (while the traditional Porsolt analysis does not) which allows selective breeding of 'motivated' and 'depressed' lines of animals.

  17. Construction of PREMUX and preliminary experimental results, as preparation for the HCPB breeder unit mock-up testing

    Energy Technology Data Exchange (ETDEWEB)

    Hernández, F., E-mail: francisco.hernandez@kit.edu [Karlsruhe Institute of Technology (KIT), Institute for Neutron Physics and Reactor Technology (INR) (Germany); Kolb, M. [Karlsruhe Institute of Technology (KIT), Institute for Applied Materials (IAM-WPT) (Germany); Annabattula, R. [Indian Institute of Technology Madras (IITM), Department of Mechanical Engineering (India); Weth, A. von der [Karlsruhe Institute of Technology (KIT), Institute for Neutron Physics and Reactor Technology (INR) (Germany)

    2014-10-15

    Highlights: • PREMUX has been constructed as preparation for a future out-of-pile thermo-mechanical qualification of a HCPB breeder unit mock-up. • The rationale and constructive details of PREMUX are reported in this paper. • PREMUX serves as a test rig for the new heater system developed for the HCPB-BU mock-up. • PREMUX will be used as benchmark for the thermal and thermo-mechanical models developed in ANSYS for the pebble beds of the HCPB-BU. • Preliminary results show the functionality of PREMUX and the good agreement of the measured temperatures with the thermal model developed in ANSYS. - Abstract: One of the European blanket designs for ITER is the Helium Cooled Pebble Bed (HCPB) blanket. The core of the HCPB-TBM consists of so-called breeder units (BUs), which encloses beryllium as neutron multiplier and lithium orthosilicate (Li{sub 4}SiO{sub 4}) as tritium breeder in form of pebble beds. After the design phase of the HCPB-BU, a non-nuclear thermal and thermo-mechanical qualification program for this device is running at the Karlsruhe Institute of Technology. Before the complex full scale BU testing, a pre-test mock-up experiment (PREMUX) has been constructed, which consists of a slice of the BU containing the Li{sub 4}SiO{sub 4} pebble bed. PREMUX is going to be operated under highly ITER-relevant conditions and has the following goals: (1) as a testing rig of new heater concept based on a matrix of wire heaters, (2) as benchmark for the existing finite element method (FEM) codes used for the thermo-mechanical assessment of the Li{sub 4}SiO{sub 4} pebble bed, and (3) in situ measurement of thermal conductivity of the Li{sub 4}SiO{sub 4} pebble bed during the tests. This paper describes the construction of PREMUX, its rationale and the experimental campaign planned with the device. Preliminary results testing the algorithm used for the temperature reconstruction of the pebble bed are reported and compared qualitatively with first analyses

  18. Frequency of Bacterial Contamination and Antibiotic Resistance Patterns in Devices and in Personnel of Endoscopy and Colonoscopy Units

    Directory of Open Access Journals (Sweden)

    Torabi, P. (BSc

    2014-06-01

    Full Text Available Background and Objective: This study was aimed to determine the extent of bacterial contamination and drug resistance patterns of isolates colonized in colonoscope and endoscope and in relevant personnel. Material and Methods: A total of 107 samples were obtained from staff of endoscopy and colonoscopy units (SEU and SCU and gastroenterological imaging equipment. For isolation and identification of the bacteria, swab culture method and biochemical identification test were used, respectively. Antimicrobial resistance profiles, multi-drug resistance (MDR patterns and phenetic relatedness of these isolates were also analyzed according to standard methods. Results: Most frequent pathogenic bacteria among the SEU and gastroenterological imaging related equipments were included S. aureus (20.8 % and 0 %; Enterococcus spp. (0 % and 5.4%; Pseudomonas spp. (0% and 13.5 %, and Clostridium difficile (0% and 12.5%. Analysis of resistance phenotypes showed a high frequency of MDR phenotypes among the SEU (82.1%, and also in endoscopes, colonoscopes, and other equipments (20%, 50% and 100%, respectively. Phylotyping of S. epidermidis isolates showed the role of staff in transmission of resistance strains to medical equipments and also circulation of strains with identical resistance phenotype among the studied samples. Conclusion: High frequency of pathogenic bacteria in colonoscopes, endoscopes and in the staff of endoscopy & colonoscopy units, and also contamination of these instruments with MDR pathogens emphasize the need for proper disinfection of endoscopes and colonoscopes and also instruction of staff in these units. Key words: Bacterial Contamination; Endoscope; Colonoscope; Antimicrobial Resistance; Gastrointestinal Disease.

  19. Autocodecovergen: Prototype Of Data Driven Unit Test Genration Tool That Guarantees 100% Code Coverage For C#

    Directory of Open Access Journals (Sweden)

    Arpit Christi

    2012-10-01

    Full Text Available Unit testing has become an integral part of software development process as it ensures all your individualfunctions behave in a way they should behave. Obtaining 100% code coverage out of unit test suit isessential to ensure that all code paths are covered. This paper proposes a tool AutoCodeCoverGen thatguarantees 100% code coverage. It also discusses the core idea behind tool and evolution of the tool.Also, it shows how the tool differs from existing tools and what benefits it reaps for its users.

  20. Fatigue Test of Cytochrome C Self-Assembled on a 11-MUA Layer Based on Electrochemical Analysis for Bioelectronic Device.

    Science.gov (United States)

    Lee, Taek; Chung, Yong-Ho; Chen, Qi; Min, Junhong; Choi, Jeong-Woo

    2015-08-01

    A cytochrome c/11-MUA heterolayer was fabricated to analyze its electrochemical characteristics in harsh conditions for a stable bioelectronic device. Since a cytochrome c/11-MUA heterolayer has been applied to construct the bioelectronics device such as non-volatile biomemory device, an understanding of electrochemical property of the heterolayer in harsh conditions such as variation of temperature and pH, and repetition of usage is necessary to manufacture a stable platform of bioelectronic device. Cytochrome c, a metalloprotein to have a heme group, was self-assembled on the Au surface via the chemical linker 11-mercaptoundecanoic acid (11-MUA). Immobilization of the heterolayer was confirmed by surface-enhanced Raman spectroscopy (SERS) and scanning tunneling microscopy (STM). The fatigue test was done by investigating the redox properties based on cyclic voltammetry (CV) of the heterolayer. The retention time test and pH dependence, thermal test of the fabricated heterolayer were conducted by CV, which showed that the fabricated film retained redox properties for more than 33 days, and from pH 5.0 to pH 9.0, from 15 °C to 55 °C. Taken together, our results show that a cytochrome c/11-MUA heterolayer is very stable, which could be used as a platform of bioelectronic device.

  1. Testing a Novel 3D Printed Radiographic Imaging Device for Use in Forensic Odontology.

    Science.gov (United States)

    Newcomb, Tara L; Bruhn, Ann M; Giles, Bridget; Garcia, Hector M; Diawara, Norou

    2017-01-01

    There are specific challenges related to forensic dental radiology and difficulties in aligning X-ray equipment to teeth of interest. Researchers used 3D printing to create a new device, the combined holding and aiming device (CHAD), to address the positioning limitations of current dental X-ray devices. Participants (N = 24) used the CHAD, soft dental wax, and a modified external aiming device (MEAD) to determine device preference, radiographer's efficiency, and technique errors. Each participant exposed six X-rays per device for a total of 432 X-rays scored. A significant difference was found at the 0.05 level between the three devices (p = 0.0015), with the MEAD having the least amount of total errors and soft dental wax taking the least amount of time. Total errors were highest when participants used soft dental wax-both the MEAD and the CHAD performed best overall. Further research in forensic dental radiology and use of holding devices is needed.

  2. Design and Development of a Miniaturized Percutaneously Deployable Wireless Left Ventricular Assist Device: Early Prototypes and Feasibility Testing.

    Science.gov (United States)

    Letzen, Brian; Park, Jiheum; Tuzun, Zeynep; Bonde, Pramod

    2017-09-21

    The current left ventricular assist devices (LVADs) are limited by a highly invasive implantation procedure in a severely unstable group of advanced heart failure patients. Additionally, the current transcutaneous power drive line acts as a nidus for infection resulting in significant morbidity and mortality. In an effort to decrease this invasiveness and eliminate drive line complications, we have conceived a wireless miniaturized percutaneous LVAD, capable of being delivered endovascularly with a tether-free operation. The system obviates the need for a transcutaneous fluid purge line required in existing temporary devices by utilizing an incorporated magnetically coupled impeller for a complete seal. The objective of this article was to demonstrate early development and proof-of-concept feasibility testing to serve as the groundwork for future formalized device development. Five early prototypes were designed and constructed to iteratively minimize the pump size and improve fluid dynamic performance. Various magnetic coupling configurations were tested. Using SolidWorks and ANSYS software for modeling and simulation, several geometric parameters were varied. HQ curves were constructed from preliminary in vitro testing to characterize the pump performance. Bench top tests showed no-slip magnetic coupling of the impeller to the driveshaft up to the current limit of the motor. The pump power requirements were tested in vitro and were within the appropriate range for powering via a wireless energy transfer system. Our results demonstrate the proof-of-concept feasibility of a novel endovascular cardiac assist device with the potential to eventually offer patients an untethered, minimally invasive support.

  3. MEMS Device for Quantitative In Situ Mechanical Testing in Electron Microscope

    Directory of Open Access Journals (Sweden)

    Xiaodong Wang

    2017-01-01

    Full Text Available In this work, we designed a micro-electromechanical systems (MEMS device that allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of nanomaterial microstructure within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to measure the force and displacement of nanomaterials qualitatively, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 5.47 μm and a load range limit of 55.0 mN.

  4. Emissions of Transport Refrigeration Units with CARB Diesel, Gas-to-Liquid Diesel, and Emissions Control Devices

    Energy Technology Data Exchange (ETDEWEB)

    Barnitt, R. A.; Chernich, D.; Burnitzki, M.; Oshinuga, A.; Miyasato, M.; Lucht, E.; van der Merwe, D.; Schaberg, P.

    2010-05-01

    A novel in situ method was used to measure emissions and fuel consumption of transport refrigeration units (TRUs). The test matrix included two fuels, two exhaust configurations, and two TRU engine operating speeds. Test fuels were California ultra low sulfur diesel and gas-to-liquid (GTL) diesel. Exhaust configurations were a stock muffler and a Thermo King pDPF diesel particulate filter. The TRU engine operating speeds were high and low, controlled by the TRU user interface. Results indicate that GTL diesel fuel reduces all regulated emissions at high and low engine speeds. Application of a Thermo King pDPF reduced regulated emissions, sometimes almost entirely. The application of both GTL diesel and a Thermo King pDPF reduced regulated emissions at high engine speed, but showed an increase in oxides of nitrogen at low engine speed.

  5. Clinical utility of the Hopkins Competency Assessment Test on an inpatient geropsychiatry unit.

    Science.gov (United States)

    Wilkins, Kirsten M; Lund, Brian C; McAdams, Jimmie D; Yates, William R

    2009-01-01

    This study examined the clinical use of routine administration of the Hopkins Competency Assessment Test on an inpatient geropsychiatry unit. The purpose was to determine whether the Hopkins Competency Assessment Test results influenced the psychiatrist's capacity assessment or confidence in that determination. The test was administered to all patients admitted voluntarily during an 18-week period. The attending psychiatrist determined treatment consent capacity and rated confidence in that determination, before and after review of the test results. Fifty seven patients were assessed. After review of the test results, the psychiatrist's capacity rating changed in only 2 (3.5%) cases. However, the test increased the psychiatrist's confidence ratings, particularly among the patients with cognitive impairment. The Hopkins Competency Assessment Test is not suited for routine administration among geropsychiatry inpatients. However, the test may serve a role as a supplementary tool for assessing treatment consent capacity among patients with evidence of cognitive impairment.

  6. Understanding benefits and addressing misperceptions and barriers to intrauterine device access among populations in the United States

    Directory of Open Access Journals (Sweden)

    Yoost J

    2014-07-01

    Full Text Available Jennie Yoost Marshall University Department of Obstetrics and Gynecology, Huntington, WV, USA Abstract: Three intrauterine devices (IUDs, one copper and two containing the progestin levonorgestrel, are available for use in the United States. IUDs offer higher rates of contraceptive efficacy than nonlong-acting methods, and several studies have demonstrated higher satisfaction rates and continuation rates of any birth control method. This efficacy is not affected by age or parity. The safety of IUDs is well studied, and the risks of pelvic inflammatory disease, perforation, expulsion, and ectopic pregnancy are all of very low incidence. Noncontraceptive benefits include decreased menstrual blood loss, improved dysmenorrhea, improved pelvic pain associated with endometriosis, and protection of the endometrium from hyperplasia. The use of IUDs is accepted in patients with multiple medical problems who may have contraindications to other birth control methods. Yet despite well-published data, concerns and misperceptions still persist, especially among younger populations and nulliparous women. Medical governing bodies advocate for use of IUDs in these populations, as safety and efficacy is unchanged, and IUDs have been shown to decrease unintended pregnancies. Dispersion of accurate information among patients and practitioners is needed to further increase the acceptability and use of IUDs. Keywords: IUD, contraception, levonorgestrel, copper

  7. Corrective Action Investigation Plan for Corrective Action Unit 543: Liquid Disposal Units, Nevada Test Site, Nevada: Revision 0

    Energy Technology Data Exchange (ETDEWEB)

    U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office

    2004-05-03

    The general purpose of this Corrective Action Investigation Plan is to ensure that adequate data are collected to provide sufficient and reliable information to identify, evaluate, and select technically viable corrective action alternatives (CAAs) for Corrective Action Unit (CAU) 543: Liquid Disposal Units, Nevada Test Site (NTS), Nevada. Located in Areas 6 and 15 on the NTS, CAU 543 is comprised of a total of seven corrective action sites (CASs), one in Area 6 and six in Area 15. The CAS in Area 6 consists of a Decontamination Facility and its components which are associated with decontamination of equipment, vehicles, and materials related to nuclear testing. The six CASs in Area 15 are located at the U.S. Environmental Protection Agency Farm and are related to waste disposal activities at the farm. Sources of possible contamination at Area 6 include potentially contaminated process waste effluent discharged through a process waste system, a sanitary waste stream generated within buildings of the Decon Facility, and radiologically contaminated materials stored within a portion of the facility yard. At Area 15, sources of potential contamination are associated with the dairy operations and the animal tests and experiments involving radionuclide uptake. Identified contaminants of potential concern include volatile organic compounds, semivolatile organic compounds, petroleum hydrocarbons, pesticides, herbicides, polychlorinated biphenyls, metals, and radionuclides. Three corrective action closure alternatives - No Further Action, Close in Place, or Clean Closure - will be recommended for CAU 543 based on an evaluation of all the data quality objective-related data. Field work will be conducted following approval of the plan. The results of the field investigation will support a defensible evaluation of CAAs that will be presented in the Corrective Action Decision Document.

  8. Cold-end Subsystem Testing for the Fission Power System Technology Demonstration Unit

    Science.gov (United States)

    Briggs, Maxwell; Gibson, Marc; Ellis, David; Sanzi, James

    2013-01-01

    The Fission Power System (FPS) Technology Demonstration Unit (TDU) consists of a pumped sodium-potassium (NaK) loop that provides heat to a Stirling Power Conversion Unit (PCU), which converts some of that heat into electricity and rejects the waste heat to a pumped water loop. Each of the TDU subsystems is being tested independently prior to full system testing at the NASA Glenn Research Center. The pumped NaK loop is being tested at NASA Marshall Space Flight Center; the Stirling PCU and electrical controller are being tested by Sunpower Inc.; and the pumped water loop is being tested at Glenn. This paper describes cold-end subsystem setup and testing at Glenn. The TDU cold end has been assembled in Vacuum Facility 6 (VF 6) at Glenn, the same chamber that will be used for TDU testing. Cold-end testing in VF 6 will demonstrate functionality; validated cold-end fill, drain, and emergency backup systems; and generated pump performance and system pressure drop data used to validate models. In addition, a low-cost proof-of concept radiator has been built and tested at Glenn, validating the design and demonstrating the feasibility of using low-cost metal radiators as an alternative to high-cost composite radiators in an end-to-end TDU test.

  9. Siddhartha: Domain-specific unit test generation for "low-testibility" programs

    Science.gov (United States)

    Reyes, Arthur Alexander

    This Dissertation validates the hypothesis that domain-specific language (DSL) methodology can provide essential automation support for specification-based testing (SBT) of computer program units expressed in difficult-to-test (i.e., "low-testability"), domain-specific design styles. This Dissertation presents Siddhartha, an extension to DSL methodology for development of program synthesizers to support SBT methods in novel application domains. Synthesizers map formal test data specifications (TestSpecs) into unit test driver procedures (Drivers). Both TestSpecs and Driver reference designs are represented via DSLs. Synthesizer development is iterative and example-driven. A Domain Designer applying the Siddhartha methodology in a novel application domain first selects a collection of general, example TestSpecs, then manually codes a collection of corresponding Drivers. Each Driver is expressed in a different reference design that specifically accommodates difficult-to-test, domain-specific program unit under test (UUT) design styles. After selecting the most promising Driver reference design, the set of (TestSpec, Driver) pairs become test cases for the synthesizer under development. The Domain Designer then designs a TestSpec→Driver translation function. The translation function maps TestSpecs to Driver kernels in the selected reference design. The translation function design simplifies DSL development by modularizing both TestSpec and Driver reference design DSLs into syntactic productions. This effectively optimizes DSL representations to support efficient TestSpec→Driver synthesis. This Dissertation validates the hypothesis by answering the question "What are the relative costs and benefits of applying DSL methods to generate requirements-based and regression Drivers for a flight control system expressed in Ada?" Costs and benefits are measured with respect to manually coded Drivers, which are arguably equivalent to Drivers generated by a general

  10. Pilot unit testing of scale inhibitors at geopressured energy well sites

    Energy Technology Data Exchange (ETDEWEB)

    Mouche, R.J.; Matson, M.L.; Matson, J.V.; Bebout, D.G.; Bachman, A.L. (eds.)

    1981-01-01

    The skid-mounted pilot unit is a smaller version of the main surface equipment used at geothermal geopressured well sites. It will be used to monitor the effectiveness of scale and corrosion inhibitors for the preventing of scaling and corrosion in the main surface equipment. The pilot unit will model the main surface equipment with respect to pressure, flow velocities, and scale inhibitor injection. The pilot unit will also operate under other conditions for optimization determination. Scaling tendencies will be monitored by specially shaped mild steel coupons placed at critical locations throughout the pilot unit. The coupons will be checked at regular intervals, and analysis will include visual, weight and EDAX-SEM analysis. Various scale inhibitors will be tested over a large range of dosage levels in order to screen inhibitors and their effectiveness for water with particular quality parameters.

  11. Description of a digital computer simulation of an Annular Momentum Control Device (AMCD) laboratory test model

    Science.gov (United States)

    Woolley, C. T.; Groom, N. J.

    1981-01-01

    A description of a digital computer simulation of an Annular Momentum Control Device (AMCD) laboratory model is presented. The AMCD is a momentum exchange device which is under development as an advanced control effector for spacecraft attitude control systems. The digital computer simulation of this device incorporates the following models: six degree of freedom rigid body dynamics; rim warp; controller dynamics; nonlinear distributed element axial bearings; as well as power driver and power supply current limits. An annotated FORTRAN IV source code listing of the computer program is included.

  12. Corrective Action Plan for Corrective Action Unit 424: Area 3 Landfill Complex, Tonopah Test Range, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Bechtel Nevada

    1998-08-31

    This corrective action plan provides the closure implementation methods for the Area 3 Landfill Complex, Corrective Action Unit (CAU) 424, located at the Tonopah Test Range. The Area 3 Landfill Complex consists of 8 landfill sites, each designated as a separate corrective action site.

  13. Acoustic monitoring systems tests at Indian Point Unit 1. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Smith, J.R.; Rao, G.V.; Craig, J.

    1979-12-01

    This report describes the results of a program to test acoustic monitoring systems on Indian Point Unit No. 1 under actual plant operating conditions, less the reactor core. The two types of systems evaluated were the monitoring of acoustic emissions generated by growing flaws and the monitoring of acoustic signals from leaks.

  14. Performance and Environmental Test Results of the High Voltage Hall Accelerator Engineering Development Unit

    Science.gov (United States)

    Kamhawi, Hani; Haag, Thomas; Huang, Wensheng; Shastry, Rohit; Pinero, Luis; Peterson, Todd; Mathers, Alex

    2012-01-01

    NASA Science Mission Directorate's In-Space Propulsion Technology Program is sponsoring the development of a 3.5 kW-class engineering development unit Hall thruster for implementation in NASA science and exploration missions. NASA Glenn and Aerojet are developing a high fidelity high voltage Hall accelerator that can achieve specific impulse magnitudes greater than 2,700 seconds and xenon throughput capability in excess of 300 kilograms. Performance, plume mappings, thermal characterization, and vibration tests of the high voltage Hall accelerator engineering development unit have been performed. Performance test results indicated that at 3.9 kW the thruster achieved a total thrust efficiency and specific impulse of 58%, and 2,700 sec, respectively. Thermal characterization tests indicated that the thruster component temperatures were within the prescribed material maximum operating temperature limits during full power thruster operation. Finally, thruster vibration tests indicated that the thruster survived the 3-axes qualification full-level random vibration test series. Pre and post-vibration test performance mappings indicated almost identical thruster performance. Finally, an update on the development progress of a power processing unit and a xenon feed system is provided.

  15. Ground test challenges in the development of the Space Shuttle orbiter auxiliary power unit

    Science.gov (United States)

    Chaffee, N. H.; Lance, R. J.; Weary, D. P.

    1984-01-01

    A conventional aircraft hydraulic system design approach was selected to provide fluid power for the Space Shuttle Orbiter. Developing the power unit, known as the Auxiliary Power Unit (APU), to drive the hydraulic pumps presented a major technological challenge. A small, high speed turbine drive unit powered by catalytically decomposed hydrazine and operating in the pulse mode was selected to meet the requirement. Because of limitations of vendor test facilities, significant portions of the development, flight qualification, and postflight anomaly testing of the Orbiter APU were accomplished at the Johnson Space Center (JSC) test facilities. This paper discusses the unique requirements of attitude, gravity forces, pressure profiles, and thermal environments which had to be satisfied by the APU, and presents the unique test facility and simulation techniques employed to meet the ground test requirements. In particular, the development of the zero-g lubrication system, the development of necessary APU thermal control techniques, the accomplishment of integrated systems tests, and the postflight investigation of the APU lube oil cooler behavior are discussed.

  16. Corrective Action Investigation Plan for Corrective Action Unit 374: Area 20 Schooner Unit Crater Nevada Test Site, Nevada, Revision 0

    Energy Technology Data Exchange (ETDEWEB)

    Patrick Matthews

    2010-02-01

    Corrective Action Unit 374 is located in Areas 18 and 20 of the Nevada Test Site, which is approximately 65 miles northwest of Las Vegas, Nevada. Corrective Action Unit 374 comprises the five corrective action sites (CASs) listed below: • 18-22-05, Drum • 18-22-06, Drums (20) • 18-22-08, Drum • 18-23-01, Danny Boy Contamination Area • 20-45-03, U-20u Crater (Schooner) These sites are being investigated because existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives (CAAs). Additional information will be obtained by conducting a corrective action investigation before evaluating CAAs and selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible evaluation of viable CAAs that will be presented in the Corrective Action Decision Document. The sites will be investigated based on the data quality objectives (DQOs) developed on October 20, 2009, by representatives of the Nevada Division of Environmental Protection and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office. The DQO process was used to identify and define the type, amount, and quality of data needed to develop and evaluate appropriate corrective actions for CAU 374.

  17. FDA OKs High-Tech Diabetes Device to Help Replace Fingerstick Tests

    Science.gov (United States)

    ... page: https://medlineplus.gov/news/fullstory_162638.html FDA OKs High-Tech Diabetes Device to Help Replace ... too low, and potentially incorrect insulin dosing, the FDA said. The Dexcom G5 is the first continuous ...

  18. Analysis on Supporting Stability for Track Subgrade Dynamic Response In-situ Test Device Based on NSGA-II

    Directory of Open Access Journals (Sweden)

    Feilong Zheng

    2013-07-01

    Full Text Available The dynamic response test to the subgrade plays a very important role in railway construction and a new in-situ test system is proposed. This paper presents the application of non-dominated sorting genetic algorithm-II (NSGA-II to analyze the stability of the supporting equipment for track subgrade dynamic response in-situ test device. Its stability is related with the extension length of the hydraulic cylinders and the backward condition of the supporting equipment - the hydraulic excavator. The problem is formulated as a multi-objective optimization problem with the objective of maximizing  the supporting force for the test device. An 85 tons excavator is picked as the case to study. The first optimal results show the excavator may not support the test system successfully. After redesigning the boom and adding its weight and length as new parameters, the second optimize results indicate the test device can work normally.

  19. Standard Test Method for Application of Ionization Chambers to Assess the Low Energy Gamma Component of Cobalt-60 Irradiators Used in Radiation-Hardness Testing of Silicon Electronic Devices

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2010-01-01

    1.1 Low energy components in the photon energy spectrum of Co-60 irradiators lead to absorbed dose enhancement effects in the radiation-hardness testing of silicon electronic devices. These low energy components may lead to errors in determining the absorbed dose in a specific device under test. This method covers procedures for the use of a specialized ionization chamber to determine a figure of merit for the relative importance of such effects. It also gives the design and instructions for assembling this chamber. 1.2 This method is applicable to measurements in Co-60 radiation fields where the range of exposure rates is 7 × 10 −6 to 3 × 10−2 C kg −1 s−1 (approximately 100 R/h to 100 R/s). For guidance in applying this method to radiation fields where the exposure rate is >100 R/s, see Appendix X1. Note 1—See Terminology E170 for definition of exposure and its units. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information onl...

  20. Research methodology simplification for teaching purposes illustrated by clutch automatic control device testing

    Science.gov (United States)

    Wojs, J.

    2016-09-01

    The paper proves that simplified, shorter examination of an object, feasible in laboratory classes, can produce results similar to those reached in scientific investigation of the device using extensive equipment. A thorough investigation of an object, an automatic clutch device in this case, enabled identifying the magnitudes that most significantly affect its operation. The knowledge of these most sensitive magnitudes allows focusing in the teaching process on simplified measurement of only selected magnitudes and verifying the given object in the positive or negative.

  1. Trends in use of the only Food and Drug Administration-approved commercially available fenestrated endovascular aneurysm repair device in the United States.

    Science.gov (United States)

    Simons, Jessica P; Shue, Bing; Flahive, Julie M; Aiello, Francesco A; Steppacher, Robert C; Eaton, Elizabeth A; Messina, Louis M; Schanzer, Andres

    2017-05-01

    Fenestrated endografts are customized, patient-specific, endovascular devices with potential to significantly reduce morbidity and mortality of short-neck infrarenal and juxtarenal abdominal aortic aneurysm repair. The Zenith fenestrated endovascular graft (ZFEN) for abdominal aortic aneurysms (Cook Medical, Bloomington, Ind), Food and Drug Administration-approved in 2012, remains the only fenestrated device available in the United States. This technology is among the most technically complex catheter-based procedures and, therefore, inherently associated with serious risk for device-related complications. We sought to define patterns of physician and hospital adoption of ZFEN. Deidentified datasets containing numbers of physicians trained, orders by physicians and hospitals, and designs (fenestration/scallop configuration) was provided for U.S. ZFEN devices ordered (April 2012-August 2015). We evaluated the number of physicians trained, the number of devices ordered, hospital characteristics, and fenestration/scallop design configurations. Cook Medical assembled the datasets but played no role in study design, analysis, or interpretation of data. Between April 2012 and August 2015, 553 physicians attended formal ZFEN training sessions, 388 (70%) of whom ordered a total of 2669 devices. An increase in orders per month (nine in June 2012 and 91 in August 2015, 911% growth; P 20 devices. For physicians contributing >6 months of data (n = 336), the average number of devices ordered per year was three (standard deviation, 4); 272 (81%) ordered ≤ 5 devices/year, 15 (4.5%) ordered 11-20 devices/year, and 3 (0.9%) ordered >20 devices/year. Of devices with design details available (2618 of 2669; 98%), most common designs were 2 small fenestrations/1 scallop (1443; 55%), 2 small fenestrations/1 large fenestration (568; 22%), 1 small fenestration/1 scallop (173, 6.6%), and 2 small fenestrations (169; 6.5%). The average number of target vessels incorporated in each

  2. Factors determining patients' intentions to use point-of-care testing medical devices for self-monitoring: the case of international normalized ratio self-testing

    Directory of Open Access Journals (Sweden)

    Shah SG

    2012-12-01

    Full Text Available Syed Ghulam Sarwar Shah,1 Julie Barnett,1 Jasna Kuljis,2 Kate Hone,2 Richard Kaczmarski31Multidisciplinary Assessment of Technology Centre for Healthcare, 2Department of Information Systems and Computing, Brunel University London, Uxbridge, Middlesex, UK; 3Department of Haematology, Hillingdon Hospital, Uxbridge, Middlesex, UKPurpose: To identify factors that determine patients' intentions to use point-of-care medical devices, ie, portable coagulometer devices for self-testing of the international normalized ratio (INR required for ongoing monitoring of blood-coagulation intensity among patients on long-term oral anticoagulation therapy with vitamin K antagonists, eg, warfarin.Methods: A cross-sectional study that applied the technology-acceptance model through a self-completed questionnaire, which was administered to a convenience sample of 125 outpatients attending outpatient anticoagulation services at a district general hospital in London, UK. Data were analyzed using descriptive statistics, factor analyses, and structural equation modeling.Results: The participants were mainly male (64% and aged ≥ 71 years (60%. All these patients were attending the hospital outpatient anticoagulation clinic for INR testing; only two patients were currently using INR self-testing, 84% of patients had no knowledge about INR self-testing using a portable coagulometer device, and 96% of patients were never offered the option of the INR self-testing. A significant structural equation model explaining 79% of the variance in patients’ intentions to use INR self-testing was observed. The significant predictors that directly affected patients' intention to use INR self-testing were the perception of technology (β = 0.92, P < 0.001, trust in doctor (β = −0.24, P = 0.028, and affordability (β = 0.15, P = 0.016. In addition, the perception of technology was significantly affected by trust in doctor (β = 0.43, P = 0.002, age (β = −0.32, P < 0.001, and

  3. Initial closed operation of the CELSS Test Facility Engineering Development Unit

    Science.gov (United States)

    Kliss, M.; Blackwell, C.; Zografos, A.; Drews, M.; MacElroy, R.; McKenna, R.; Heyenga, A. G.

    2003-01-01

    As part of the NASA Advanced Life Support Flight Program, a Controlled Ecological Life Support System (CELSS) Test Facility Engineering Development Unit has been constructed and is undergoing initial operational testing at NASA Ames Research Center. The Engineering Development Unit (EDU) is a tightly closed, stringently controlled, ground-based testbed which provides a broad range of environmental conditions under which a variety of CELSS higher plant crops can be grown. Although the EDU was developed primarily to provide near-term engineering data and a realistic determination of the subsystem and system requirements necessary for the fabrication of a comparable flight unit, the EDU has also provided a means to evaluate plant crop productivity and physiology under controlled conditions. This paper describes the initial closed operational testing of the EDU, with emphasis on the hardware performance capabilities. Measured performance data during a 28-day closed operation period are compared with the specified functional requirements, and an example of inferring crop growth parameters from the test data is presented. Plans for future science and technology testing are also discussed. Published by Elsevier Science Ltd on behalf of COSPAR.

  4. Cosmo Cassette: A Microfluidic Microgravity Microbial System For Synthetic Biology Unit Tests and Satellite Missions

    Science.gov (United States)

    Berliner, Aaron J.

    2013-01-01

    Although methods in the design-build-test life cycle of the synthetic biology field have grown rapidly, the expansion has been non-uniform. The design and build stages in development have seen innovations in the form of biological CAD and more efficient means for building DNA, RNA, and other biological constructs. The testing phase of the cycle remains in need of innovation. Presented will be both a theoretical abstraction of biological measurement and a practical demonstration of a microfluidics-based platform for characterizing synthetic biological phenomena. Such a platform demonstrates a design of additive manufacturing (3D printing) for construction of a microbial fuel cell (MFC) to be used in experiments carried out in space. First, the biocompatibility of the polypropylene chassis will be demonstrated. The novel MFCs will be cheaper, and faster to make and iterate through designs. The novel design will contain a manifold switchingdistribution system and an integrated in-chip set of reagent reservoirs fabricated via 3D printing. The automated nature of the 3D printing yields itself to higher resolution switching valves and leads to smaller sized payloads, lower cost, reduced power and a standardized platform for synthetic biology unit tests on Earth and in space. It will be demonstrated that the application of unit testing in synthetic biology will lead to the automatic construction and validation of desired constructs. Unit testing methodologies offer benefits of preemptive problem identification, change of facility, simplicity of integration, ease of documentation, and separation of interface from implementation, and automated design.

  5. Modern technical solutions of gas-fired heating devices of household and communal use and analysis of their testing

    Energy Technology Data Exchange (ETDEWEB)

    Bodzon, L.; Radwan, W. [Oil Mining and Gas Engineering Institute, Cracow (Poland)

    1995-12-31

    A review of technical solutions for gas-fired heating devices for household and communal use in Poland is presented. Based upon the analysis it is stated that the power output of Polish and foreign boilers ranges between 9 and 35 kW. The carbon monoxide content in flue gases reaches (on average) 0.005 vol.%, i.e., it is much lower than the maximum permissible level. Temperature of flue gases (excluding condensation boilers and those with air-tight combustion chamber) ranges between 150 and 200{degrees}C and their heating efficiency reaches 87-93%. The best parameters are given for condensation boilers, however they are still not widespread in Poland for the high cost of the equipment and assembling works. Among the heaters, the most safe are convection devices with closed combustion chamber; their efficiency is also the highest. Thus, it is concluded that a wide spectrum of high efficiency heating devices with good combustion parameters are available. The range of output is sufficient to meet household and communal requirement. They are however - predominantly - units manufactured abroad. It is difficult to formulate the program aimed at the improvement of the technique of heating devices made in Poland, and its implementation is uncertain because the production process is broken up into small handicraft workshops.

  6. Compute-unified device architecture implementation of a block-matching algorithm for multiple graphical processing unit cards

    Science.gov (United States)

    Massanes, Francesc; Cadennes, Marie; Brankov, Jovan G.

    2011-07-01

    We describe and evaluate a fast implementation of a classical block-matching motion estimation algorithm for multiple graphical processing units (GPUs) using the compute unified device architecture computing engine. The implemented block-matching algorithm uses summed absolute difference error criterion and full grid search (FS) for finding optimal block displacement. In this evaluation, we compared the execution time of a GPU and CPU implementation for images of various sizes, using integer and noninteger search grids. The results show that use of a GPU card can shorten computation time by a factor of 200 times for integer and 1000 times for a noninteger search grid. The additional speedup for a noninteger search grid comes from the fact that GPU has built-in hardware for image interpolation. Further, when using multiple GPU cards, the presented evaluation shows the importance of the data splitting method across multiple cards, but an almost linear speedup with a number of cards is achievable. In addition, we compared the execution time of the proposed FS GPU implementation with two existing, highly optimized nonfull grid search CPU-based motion estimations methods, namely implementation of the Pyramidal Lucas Kanade Optical flow algorithm in OpenCV and simplified unsymmetrical multi-hexagon search in H.264/AVC standard. In these comparisons, FS GPU implementation still showed modest improvement even though the computational complexity of FS GPU implementation is substantially higher than non-FS CPU implementation. We also demonstrated that for an image sequence of 720 × 480 pixels in resolution commonly used in video surveillance, the proposed GPU implementation is sufficiently fast for real-time motion estimation at 30 frames-per-second using two NVIDIA C1060 Tesla GPU cards.

  7. Is Current Account of Turkey Sustainable ? Evidence from Nonlinear Unit Root Tests

    Directory of Open Access Journals (Sweden)

    Serkan Taştan

    2015-09-01

    Full Text Available In this paper, current account sustainability of Turkey is analyzed in a nonlinear framework. Various nonlinear unit root tests have been used to test for structural break, sign and size nonlinearity. We have tested structural break and size nonlinearity separately and structural break-sign and size-sign nonlinearities simultaneously. Only considering the size nonlinearity, we have found that the current account of Turkey is sustainable. Thus, the size nonlinearity, in other words the speed of reversion to equilibrium, is essential for the current account sustainability of Turkey. We have also found that the speed of adjustment towards equilibrium is symmetric, while considering size and sign nonlinearities simultaneously.

  8. Advanced Stirling Convertor Control Unit Testing at NASA Glenn Research Center in the Radioisotope Power Systems System Integration Laboratory

    Science.gov (United States)

    Dugala, Gina M.; Taylor, Linda M.; Kussmaul, Michael; Casciani, Michael; Brown, Gregory; Wiser, Joel

    2017-01-01

    Future NASA missions could include establishing Lunar or Martian base camps, exploring Jupiters moons and travelling beyond where generating power from sunlight may be limited. Radioisotope Power Systems (RPS) provide a dependable power source for missions where inadequate sunlight or operational requirements make other power systems impractical. Over the past decade, NASA Glenn Research Center (GRC) has been supporting the development of RPSs. The Advanced Stirling Radioisotope Generator (ASRG) utilized a pair of Advanced Stirling Convertors (ASC). While flight development of the ASRG has been cancelled, much of the technology and hardware continued development and testing to guide future activities. Specifically, a controller for the convertor(s) is an integral part of a Stirling-based RPS. For the ASRG design, the controller maintains stable operation of the convertors, regulates the alternating current produced by the linear alternator of the convertor, provides a specified direct current output voltage for the spacecraft, synchronizes the piston motion of the two convertors in order to minimize vibration as well as manage and maintain operation with a stable piston amplitude and hot end temperature. It not only provides power to the spacecraft but also must regulate convertor operation to avoid damage to internal components and maintain safe thermal conditions after fueling. Lockheed Martin Coherent Technologies has designed, developed and tested an Engineering Development Unit (EDU) Advanced Stirling Convertor Control Unit (ACU) to support this effort. GRC used the ACU EDU as part of its non-nuclear representation of a RPS which also consists of a pair of Dual Advanced Stirling Convertor Simulator (DASCS), and associated support equipment to perform a test in the Radioisotope Power Systems System Integration Laboratory (RSIL). The RSIL was designed and built to evaluate hardware utilizing RPS technology. The RSIL provides insight into the electrical

  9. Developing a reproducible non-line-of-sight experimental setup for testing wireless medical device coexistence utilizing ZigBee.

    Science.gov (United States)

    LaSorte, Nickolas J; Rajab, Samer A; Refai, Hazem H

    2012-11-01

    The integration of heterogeneous wireless technologies is believed to aid revolutionary healthcare delivery in hospitals and residential care. Wireless medical device coexistence is a growing concern given the ubiquity of wireless technology. In spite of this, a consensus standard that addresses risks associated with wireless heterogeneous networks has not been adopted. This paper serves as a starting point by recommending a practice for assessing the coexistence of a wireless medical device in a non-line-of-sight environment utilizing 802.15.4 in a practical, versatile, and reproducible test setup. This paper provides an extensive survey of other coexistence studies concerning 802.15.4 and 802.11 and reports on the authors' coexistence testing inside and outside an anechoic chamber. Results are compared against a non-line-of-sight test setup. Findings relative to co-channel and adjacent channel interference were consistent with results reported in the literature.

  10. CLOSURE REPORT FOR CORRECTIVE ACTION UNIT 204: STORAGE BUNKERS, NEVADA TEST SITE, NEVADA

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-04-01

    Corrective Action Unit (CAU) 330 consists of four Corrective Action Sites (CASs) located in Areas 6, 22, and 23 of the Nevada Test Site (NTS). The unit is listed in the Federal Facility Agreement and Consent Order (FFACO, 1996) as CAU 330: Areas 6, 22, and 23 Tanks and Spill Sites. CAU 330 consists of the following CASs: CAS 06-02-04, Underground Storage Tank (UST) and Piping CAS 22-99-06, Fuel Spill CAS 23-01-02, Large Aboveground Storage Tank (AST) Farm CAS 23-25-05, Asphalt Oil Spill/Tar Release

  11. Pilot-scale treatability test plan for the 200-BP-5 operable unit

    Energy Technology Data Exchange (ETDEWEB)

    1994-08-01

    This document presents the treatability test plan for pilot-scale pump and treat testing at the 200-BP-5 Operable Unit. This treatability test plan has been prepared in response to an agreement between the U.S. Department of Energy (DOE), the U.S. Environmental Protection Agency (EPA), and the State of Washington Department of Ecology (Ecology), as documented in Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement, Ecology et al. 1989a) Change Control Form M-13-93-03 (Ecology et al. 1994) and a recent 200 NPL Agreement Change Control Form (Appendix A). The agreement also requires that, following completion of the activities described in this test plan, a 200-BP-5 Operable Unit Interim Remedial Measure (IRM) Proposed Plan be developed for use in preparing an Interim Action Record of Decision (ROD). The IRM Proposed Plan will be supported by the results of this treatability test plan, as well as by other 200-BP-5 Operable Unit activities (e.g., development of a qualitative risk assessment). Once issued, the Interim Action ROD will specify the interim action(s) for groundwater contamination at the 200-BP-5 Operable Unit. The treatability test approach is to conduct a pilot-scale pump and treat test for each of the two contaminant plumes associated with the 200-BP-5 Operable Unit. Primary contaminants of concern are {sup 99}Tc and {sup 60}Co for underwater affected by past discharges to the 216-BY Cribs, and {sup 90}Sr, {sup 239/240}Pu, and Cs for groundwater affected by past discharges to the 216-B-5 Reverse Well. The purpose of the pilot-scale treatability testing presented in this testplan is to provide the data basis for preparing an IRM Proposed Plan. To achieve this objective, treatability testing must: Assess the performance of groundwater pumping with respect to the ability to extract a significant amount of the primary contaminant mass present in the two contaminant plumes.

  12. Design and Testing of a Minimally Invasive Blood Clot Removal Device ConstructedWith Elements of Superelastic Nitinol

    Science.gov (United States)

    Puffer, Andrew J.

    Many vascular system problems stem from insufficient blood return flow to the heart. One of the main causes is a blockage within veins or arteries known as a blood clot, or thrombus. This can occur after trauma, surgery, or other phenomenological reasons. Each year in the U.S. more than 175,000 bypass procedures and more than 160,000 amputations resulting from peripheral vessel disease are performed. Clinical data indicates that clot removal devices and procedures can reduce the need for an amputation by 80 percent. Percutaneous thrombectomy refers to the removal of thrombus using catheter based non-surgical methods. The ultimate goal of any modality to treat these conditions of the arterial or venous system is to restore patency, quickly, safely, and cost effectively. Catheter directed thrombectomy and thrombolysis is less traumatic and avoids the morbidity and mortality associated with conventional surgical technique. As a result, there has been a push recently for the use of percutaneous mechanical thrombectomy (PMT) devices. However, all devices have their own set of drawbacks: distal embolization, vessel wall trauma, hemolysis, to name a few. Ongoing efforts have been made to create a prototype thrombectomy device that uses elements of superelastic nitinol (a type of shape memory alloy), that seeks to address some of the drawbacks of current devices. The prototype was designed and tested in a simulated human circulatory system along side a commercially available device (The DiverCE Clot Extraction Catheter). The test evaluated how well the devices minimized distal embolization of a human blood clot created in vitro.. Results of the testing showed that the prototype device created significantly less embolization when compared to the DiverCE particles greater than 102mum (p = 0.0332). Means were statistically not different for particles between 25mum and 102mum (p = 0.2454), and particles between 5mum and 25mum (p = 0.6524). In addition the prototype was shown

  13. Proposal of methodology and test protocol for evaluating and qualifying pH measuring devices

    Directory of Open Access Journals (Sweden)

    Niza Helena de Almeida

    2006-01-01

    Full Text Available We present a proposal for evaluating and qualifying pH measuring devices based on the requirements of relevant standards. The proposal presented is based on ASTM E70, NBR 7353, JIS Z 8805, BS 3145, DIN 19268, NBR ISO 17025 and other standards, as well as the results of field research carried out in conjunction with professionals performing pH measurements in public health laboratories. Evaluation is performed by inspection of a form which records data from the measuring system. The form gives acceptable variations in the parameters being tested and allows a conclusion to be reached regarding acceptability of the system. Using the proposed protocol allows definition of suitable analysis criteria, while taking into account the influence pH measurement is subject and the need for correct results. This is particularly true when analyzing products already on the market, thus underlining the protocol's importance to the public health area.Este artigo apresenta uma proposta de protocolo de avaliação e qualificação de medidores de pH fundamentada no que prescrevem as normas ASTM E 70, NBR 7353, JIS Z 8805, BS 3145, DIN 19268, NBR ISO 17025 e outras, complementada com os resultados de pesquisa de campo junto a profissionais que realizam ensaio de medição de pH em laboratórios de saúde pública. A proposta consiste em avaliar o medidor de pH com auxílio de um formulário, cujo preenchimento baseia-se, principalmente, na inspeção e ensaios no sistema medidor. O formulário fornece variações aceitáveis para os parâmetros testados, propiciando parecer conclusivo quanto à adequação do instrumento. A aplicação do protocolo permite definir um critério adequado de análise, tendo em vista a influência que sofre tal ensaio de medição, especialmente, em análises de amostras de produtos decorrentes de finalidade fiscal, no âmbito da saúde pública

  14. Design, fabrication and test of a pneumatically controlled, renewable, microfluidic bead trapping device for sequential injection analysis applications

    Energy Technology Data Exchange (ETDEWEB)

    Shao, Guocheng; Lu, Donglai; Fu, Zhifeng; Du, Dan; Ozanich, Richard M.; Wang, Wanjun; Lin, Yuehe

    2016-01-01

    This paper describes the design, fabrication, and testing of a pneumatically controlled,renewable, microfluidic device for conducting bead-based assays in an automated sequential injection analysis system. The device used a “brick wall”-like pillar array (pillar size: 20 μm length X 50 μm width X 45 μm height) with 5 μm gaps between the pillars serving as the micro filter. The flow channel where bead trapping occurred is 500 μm wide X 75 μm deep. An elastomeric membrane and an air chamber were located underneath the flow channel. By applying pressure to the air chamber, the membrane is deformed and pushed upward against the filter structure. This effectively traps beads larger than 5 μm and creates a “bed” or micro column of beads that can be perfused and washed with liquid samples and reagents. Upon completion of the assay process, the pressure is released and the beads are flushed out from underneath the filter structure to renew the device. Mouse IgG was used as a model analyte to test the feasibility of using the proposed device for immunoassay applications. Resulting microbeads from an on-chip fluorescent immunoassay were individually examined using flow cytometry. The results show that the fluorescence signal intensity distribution is fairly narrow indicating high chemical reaction uniformity among the beads population. Electrochemical onchip assay was also conducted. A detection limit of 0.1 ng/mL1 ppb was achieved and good device reliability and repeatability were demonstrated. The novel microfluidic-based beadstrapping device thus opens up a new pathway to design micro-bead based biosensor immunoassays for clinical and othervarious applications.

  15. The NanoBeamBalance: A passive, tensile-test device for the atomic force microscope

    Science.gov (United States)

    Wenger, M. P. E.; Mesquida, P.

    2011-05-01

    An add-on device is presented, which significantly expands the force measurement capabilities of the atomic force microscope (AFM). The device consists of a completely passive mechanism, which translates the vertical motion of the AFM tip in force measurements into a horizontal motion of two sample support pads. The advantage is that it is much easier to deposit microscopic samples from suspension onto flat surfaces than to attach them reliably between tip and a surface. The working-principle and the design of the device is comprehensively described and demonstrated on the example of collagen fibres with a diameter of a few μm. Well-defined tensile measurements in longitudinal direction were performed, showing that the tensile stiffness of collagen fibres from rat tail tendon decreases by a factor of 5 when rehydrated from a dried sample and slowly increases upon cross-linking with glutaraldehyde.

  16. A microfluidic device with multi-valves system to enable several simultaneous exposure tests on Caenorhabditis elegans

    Science.gov (United States)

    Jung, Jaehoon; Nakajima, Masahiro; Masaru, Takeuchi; Huang, Qiang; Fukuda, Toshio

    2014-03-01

    In this paper, we report on a microfluidic device with a multi-valve system to conduct several exposure tests on Caenorhabditis elegans (C. elegans) simultaneously. It has pneumatic valves and no-moving-parts (NMP) valves. An NMP valve is incorporated with a chamber and enables the unidirectional movement of C. elegans in the chamber; once worms are loaded into the chamber, they cannot exit, regardless of the flow direction. To demonstrate the ability of the NMP valve to handle worms, we made a microfluidic device with three chambers. Each chamber was used to expose worms to Cd and Cu solutions, and K-medium. A pair of electrodes was installed in the device and the capacitance in-between the electrode was measured. When a C. elegans passed through the electrodes, the capacitance was changed. The capacitance change was proportional to the body volume of the worm, thus the body volume change by the heavy metal exposure was measured in the device. Thirty worms were divided into three groups and exposed to each solution. We confirmed that the different solutions induced differences in the capacitance changes for each group. These results indicate that our device is a viable method for simultaneously analyzing the effect of multiple stimuli on C. elegans.

  17. Fabrication techniques for microfluidic paper-based analytical devices and their applications for biological testing: A review.

    Science.gov (United States)

    Xia, Yanyan; Si, Jin; Li, Zhiyang

    2016-03-15

    Paper is increasingly recognized as a user-friendly and ubiquitous substrate for construction of microfluidic devices. Microfluidic paper-based analytical devices (μPADs) provide an alternative technology for development of affordable, portable, disposable and low-cost diagnostic tools for improving point of care testing (POCT) and disease screening in the developing world, especially in those countries with no- or low-infrastructure and limited trained medical and health professionals. We in this review present fabrication techniques for microfluidic devices and their respective applications for biological detection as reported to date. These include: (i) fabrication techniques: examples of devices fabricated by using two-dimensional (2D) and three-dimensional (3D) methods; (ii) detection application: biochemical, immunological and molecular detection by incorporating efficient detection methods such as, colorimetric detection, electrochemical detection, fluorescence detection, chemiluminescence (CL) detection, electrochemiluninescence (ECL) detection, photoelectrochemi (PEC) detection and so on. In addition, main advantages, disadvantages and future trends for the devices are also discussed in this review.

  18. Development and testing of a sampling device for the analyses of suspended sediment concentrations

    Science.gov (United States)

    Schletterer, Martin; Reindl, Robert; Unterlercher, Franz; Hauer, Christoph

    2017-04-01

    Suspended sediment concentrations are not equal in time as well as within a cross section. For calibration, sampling is needed within a cross profile (using e.g. sampler US P-61-A1) or nearby of a SSC sensor. However, due to insufficient hydraulic efficiency, uncontrolled handling under water as well as lack in accuracy in starting and closing the suspended sediment sampling, the well-established extracting of water samples by hand (dip or grab sample) lacks reproducibility. Due to these shortcomings a novel measuring device has been developed for suspended sediment sampling in rivers. For the design of the presented sampler the experiences of previous technical concepts of direct suspended sediment sampling in rivers have been considered. The sampling device consists of 2 tubes: a filling pipe (8x1 mm = 6 mm inner diameter) and an exhaust pipe (6x1 mm = 4 mm inner diameter). The filling pipe is equipped thread (M8x1 mm) to attach the "measuring nozzle" made of brass. We compared three different nozzles (D4, D5, D6) in order to investigate possible effects of different filling times. Both tubes are connected (TIG -Tungsten Inert-Gaswelding) by a flat steel. All parts (despite the nozzles) are made from stainless steel. On the tubes a plastic screw cap is mounted which allows to attach (and quickly change) standard sampling bottles. A mount enables that the device can be attached to a commercially available "GARDENA aluminium handle", thus using this rod samples can be taken at certain localities. The measurement device has been designed to improve the accuracy of suspended sediment sampling in rivers. The target was to achieve an optimum in hydraulic efficiency without disturbing the natural transport dynamics. Thus, the water sample gained from this sampling device supports the calibration and validation of indirect suspended sediment sampling devices (e.g. SSC sensor). We present the design of the sampler as well as field data in comparison with conventional dip

  19. The Resonating Arm Exerciser: design and pilot testing of a mechanically passive rehabilitation device that mimics robotic active assistance.

    Science.gov (United States)

    Zondervan, Daniel K; Palafox, Lorena; Hernandez, Jorge; Reinkensmeyer, David J

    2013-04-18

    Robotic arm therapy devices that incorporate actuated assistance can enhance arm recovery, motivate patients to practice, and allow therapists to deliver semi-autonomous training. However, because such devices are often complex and actively apply forces, they have not achieved widespread use in rehabilitation clinics or at home. This paper describes the design and pilot testing of a simple, mechanically passive device that provides robot-like assistance for active arm training using the principle of mechanical resonance. The Resonating Arm Exerciser (RAE) consists of a lever that attaches to the push rim of a wheelchair, a forearm support, and an elastic band that stores energy. Patients push and pull on the lever to roll the wheelchair back and forth by about 20 cm around a neutral position. We performed two separate pilot studies of the device. In the first, we tested whether the predicted resonant properties of RAE amplified a user's arm mobility by comparing his or her active range of motion (AROM) in the device achieved during a single, sustained push and pull to the AROM achieved during rocking. In a second pilot study designed to test the therapeutic potential of the device, eight participants with chronic stroke (35 ± 24 months since injury) and a mean, stable, initial upper extremity Fugl-Meyer (FM) score of 17 ± 8 / 66 exercised with RAE for eight 45 minute sessions over three weeks. The primary outcome measure was the average AROM measured with a tilt sensor during a one minute test, and the secondary outcome measures were the FM score and the visual analog scale for arm pain. In the first pilot study, we found people with a severe motor impairment after stroke intuitively found the resonant frequency of the chair, and the mechanical resonance of RAE amplified their arm AROM by a factor of about 2. In the second pilot study, AROM increased by 66% ± 20% (p = 0.003). The mean FM score increase was 8.5 ± 4 pts (p = 0.009). Subjects did not report

  20. Monitoring dental-unit-water-line output water by current in-office test kits.

    Science.gov (United States)

    Lal, Sham; Singhrao, Sim K; Bricknell, Matt; Pearce, Mark; Morton, L H Glyn; Ahmed, Waqar; Crean, St John

    2014-08-01

    The importance of monitoring contamination levels in the output water of dental-unit-water-lines (DUWLs) is essential as they are prone to developing biofilms that may contaminate water that is used to treat patients, with opportunistic pathogens such as species of Legionella, Pseudomonas and others. Dentists and practice staff are also at risk of being infected by means of cross-infection due to aerosols generated from DUWL water. The unit of measurement for the microbial contamination of water by aerobic mesophilic heterotrophic bacteria is the colony-forming unit per millilitre (cfu/ml) of water. The UK has its own guidelines set by the Department of Health for water discharged from DUWL to be between 100 and 200 cfu/ml of water. The benchmark or accepted standard laboratory test is by microbiological culture on R2A agar plates. However, this is costly and not convenient for routine testing in dental practices. A number of commercial indicator tests are used in dental surgeries, but they were not developed for the dental market and serve only to indicate gross levels of contamination when used outside of the manufacturer's recommended incubation period. The aim of this article is to briefly review the universal problem of DUWL contamination with microbial biofilms and to update dental professionals on the availability of currently available commercial in-office monitoring systems for aerobic mesophilic heterotrophic bacteria and to discuss their limitations for testing water samples in assuring compliance with recommended guidelines.

  1. Near Earth Asteroid Scout Solar Sail Engineering Development Unit Test Suite

    Science.gov (United States)

    Lockett, Tiffany Russell; Few, Alexander; Wilson, Richard

    2017-01-01

    The Near Earth Asteroid (NEA) Scout project is a 6U reconnaissance mission to investigate a near Earth asteroid utilizing an 86m(sub 2) solar sail as the primary propulsion system. This will be the largest solar sail NASA has launched to date. NEA Scout is currently manifested on the maiden voyage of the Space Launch System in 2018. In development of the solar sail subsystem, design challenges were identified and investigated for packaging within a 6U form factor and deployment in cis-lunar space. Analysis was able to capture understanding of thermal, stress, and dynamics of the stowed system as well as mature an integrated sail membrane model for deployed flight dynamics. Full scale system testing on the ground is the optimal way to demonstrate system robustness, repeatability, and overall performance on a compressed flight schedule. To physically test the system, the team developed a flight sized engineering development unit with design features as close to flight as possible. The test suite included ascent vent, random vibration, functional deployments, thermal vacuum, and full sail deployments. All of these tests contributed towards development of the final flight unit. This paper will address several of the design challenges and lessons learned from the NEA Scout solar sail subsystem engineering development unit. Testing on the component level all the way to the integrated subsystem level. From optical properties of the sail material to fold and spooling the single sail, the team has developed a robust deployment system for the solar sail. The team completed several deployments of the sail system in preparation for flight at half scale (4m) and full scale (6.8m): boom only, half scale sail deployment, and full scale sail deployment. This paper will also address expected and received test results from ascent vent, random vibration, and deployment tests.

  2. Selection of Environmentally Friendly Solvents for the Extravehicular Mobility Unit Secondary Oxygen Pack Cold Trap Testing

    Science.gov (United States)

    Steele, John; Chullen, Cinda; Morenz, Jesse; Stephenson, Curtis

    2010-01-01

    Freon-113(TradeMark) has been used as a chemistry lab sampling solvent at NASA/JSC for EMU (extravehicular Mobility Unit) SOP (Secondary Oxygen Pack) oxygen testing Cold Traps utilized at the USA (United Space Alliance) Houston facility. Similar testing has occurred at the HSWL (Hamilton Sundstrand Windsor Locks) facility. A NASA Executive Order bans the procurement of all ODS (ozone depleting substances), including Freon-113 by the end of 2009. In order to comply with NASA direction, HSWL began evaluating viable solvents to replace Freon-113 . The study and testing effort to find Freon-113 replacements used for Cold Trap sampling is the subject of this paper. Test results have shown HFE-7100 (a 3M fluorinated ether) to be an adequate replacement for Freon-113 as a solvent to remove and measure the non-volatile residue collected in a Cold Trap during oxygen testing. Furthermore, S-316 (a Horiba Instruments Inc. high molecular weight, non-ODS chlorofluorocarbon) was found to be an adequate replacement for Freon-113 as a solvent to reconstitute non-volatile residue removed from a Cold Trap during oxygen testing for subsequent HC (hydrocarbon) analysis via FTIR (Fourier Transform Infrared Spectroscopy).

  3. Practical Testing and Performance Analysis of Phasor Measurement Unit Using Real Time Digital Simulator (RTDS)

    DEFF Research Database (Denmark)

    Liu, Leo; Rather, Zakir Hussain; Stearn, Nathen

    2012-01-01

    visualisation and post event analysis of power systems. It is expected however, that through integration with traditional Supervisory Control and Data Acquisition (SCADA) systems, closed loop control applications will be possible. Phasor Measurement Units (PMUs) are fundamental components of WAMS. Large WAMS......Wide Area Measurement Systems (WAMS) and Wide Area Monitoring, Protection and Control Systems (WAMPACS) have evolved rapidly over the last two decades [1]. This fast emerging technology enables real time synchronized monitoring of power systems. Presently, WAMS are mainly used for real time...... may support PMUs from multiple manufacturers and therefore it is important that there is a way of standardising the measurement performance of these devices. Currently the IEEE Standard C37.118 is used to quantify the measurement performance of PMUs. While standard specifications are also available...

  4. [Development of a computer-assisted thermoelectric Peltier cold test procedure with integrated photoplethysmography unit for noninvasive evaluation of acral skin circulation].

    Science.gov (United States)

    Klyscz, T; Hahn, M; Beck, W; Blazek, V; Rassner, G; Jünger, M

    1997-09-01

    Local cold provocation tests are an important, non-invasive diagnostic tool for collecting information about skin perfusion during exposure to cold. In patients suffering from vasospastic circulatory disorders such as Raynaud's phenomenon, it is of particular importance to be able to collect data about acral circulation during the cooling test in the asymptomatic intervals between naturally occurring attacks. By carrying out a series of cold provocation tests, for example, patient response to a newly initiated therapy can be assessed. Here we present a recently developed, computer-aided thermoelectric Peltier device with an integrated finger holder for carrying out local cold provocation tests. The electronic control unit of the Peltier element make it possible to cool or heat to predefined temperatures. At the same time, the temperature of both the finger holder and the skin can be measured. A photoplethysmographic sensor is also integrated within the device, enabling the response of the pulse waves to the controlled temperature changes to be monitored accurately. It is also possible to measure simultaneously laser Doppler flux and capillary pressure in the nailfold and to perform nailfold capillaroscopy to determine red blood cell velocity. The new device provides us with the technical means to study the interrelationship between acral skin perfusion and the thermal regulation of the skin.

  5. Neutron and gamma radiation tests of the Analog Devices TMP37 temperature sensors

    CERN Document Server

    Mockett, P M; Twomey, M S

    2004-01-01

    The Analog Devices TMP37 temperature sensor is used to monitor the temperature gradients in the US ATLAS End Cap Muon Chambers. It was chosen because of its stability, linearity, high output signal, and especially the low self-heating. We have irradiated samples of these sensors with neutrons and gamma rays. The results of these measurements are presented.

  6. Highly sensitive pyrogen detection on medical devices by the monocyte activation test

    NARCIS (Netherlands)

    Stang, Katharina; Fennrich, Stefan; Krajewski, Stefanie; Stoppelkamp, Sandra; Burgener, Iwan Anton; Wendel, Hans-Peter; Post, Marcell

    Pyrogens are components of microorganisms, like bacteria, viruses or fungi, which can induce a complex inflammatory response in the human body. Pyrogen contamination on medical devices prior operation is still critical and associated with severe complications for the patients. The aim of our study

  7. Amplitude Test for Input Devices for System Control in Immersive Virtual Environment

    DEFF Research Database (Denmark)

    Stenholt, Rasmus; Thornemann Hansen, Nina; Hald, Kasper

    2014-01-01

    In this study, the amplitudes best suited to compare four input devices are examined in the context of a pointer-based system control interface for immersive virtual environments. The interfaces are based on a pen and tablet, a touch tablet, hand-tracking using Kinect and a Wii Nunchuk analog stick...

  8. Artifical Excitation of Ferro-Resonance for Testing Electrotechnical Equipment in Distribution Devices with Increased Voltage

    Directory of Open Access Journals (Sweden)

    Ye. V. Dmitriev

    2006-01-01

    Full Text Available On the basis of the developed device for protection against of ferro-resonant and high-frequency cumulative over-voltages an algorithm for obtaining a voltage imitating ferro-resonant over-voltages is proposed in the paper. This algorithm presupposes to apply a voltage to the secondary transformer side from an extraneous source is proposed.

  9. Isotope-labelled urea to test colon drug delivery devices in vivo : principles, calculations and interpretations

    NARCIS (Netherlands)

    Maurer, Marina; Schellekens, Reinout C. A.; Wutzke, Klaus D.; Stellaard, Frans

    2013-01-01

    This paper describes various methodological aspects that were encountered during the development of a system to monitor the in vivo behaviour of a newly developed colon delivery device that enables oral drug treatment of inflammatory bowel diseases. [C-13]urea was chosen as the marker substance. Rel

  10. Test-Retest Reliability of Respiratory Resistance Measured with the Airflow Perturbation Device

    Science.gov (United States)

    Gallena, Sally K.; Solomon, Nancy Pearl; Johnson, Arthur T.; Vossoughi, Jafar; Tian, Wei

    2014-01-01

    Purpose: In this study, the authors aimed to determine reliability of the airflow perturbation device (APD) to measure respiratory resistance within and across sessions during resting tidal (RTB) and postexercise breathing in healthy athletes, and during RTB across trials within a session in athletes with paradoxical vocal fold motion (PVFM)…

  11. Study on 3D printer production of auxiliary device for upper limb for medical imaging test

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyeong Gyun [Dept. of Radiological Science, Far East University, Eumsung (Korea, Republic of); Yoon, Jae Ho [Jukwang Precision Co., Ltd., Gumi (Korea, Republic of); Choi, Seong Dae [Dept. of Mechanical system engineering, Kumoh Institute of Technology, Gumi (Korea, Republic of)

    2015-12-15

    There is a progressive development in the medical imaging technology, especially of descriptive capability for anatomical structure of human body thanks to advancement of information technology and medical devices. But however maintenance of correct posture is essential for the medical imaging checkup on the shoulder joint requiring rotation of the upper limb due to the complexity of human body. In the cases of MRI examination, long duration and fixed posture are critical, as failure to comply with them leads to minimal possibility of reproducibility only with the efforts of the examiner and will of the patient. Thus, this study aimed to develop an auxiliary device that enables rotation of the upper limb as well as fixing it at quantitative angles for medical imaging examination capable of providing diagnostic values. An auxiliary device has been developed based on the results of precedent studies, by designing a 3D model with the CATIA software, an engineering application, and producing it with the 3D printer. The printer is Objet350 Connex from Stratasys, and acrylonitrile- butadiene-styrene(ABS) is used as the material of the device. Dimensions are 120 X 150 X 190 mm, with the inner diameter of the handle being 125.9 mm. The auxiliary device has 4 components including the body (outside), handle (inside), fixture terminal and the connection part. The body and handle have the gap of 2.1 mm for smooth rotation, while the 360 degree of scales have been etched on the handle so that the angle required for observation may be recorded per patient for traceability and dual examination.

  12. Evaluation of SPACE code for natural circulation test of Hanbit unit 2

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Seyun; Kim, Minhee [KHNP Central Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    SPACE (Safety and Performance Analysis Code for Nuclear Power Plants) has been developed by KHNP with the cooperation with KEPCO E and C and KAERI. SPACE code is expected to be applied to the safety analysis for LOCA (Loss of Coolant Accident) and Non-LOCA scenarios. SPACE code solves two-fluid, three-field governing equations and programmed with C++ computer language using object-oriented concepts. To evaluate the analysis capability for the passive cooling phenomenon in the actual nuclear power plant, a natural circulation test of Hanbit unit 2 was simulated with SPACE code. To evaluate the analysis capability for the passive cooling phenomenon in the actual nuclear power plant, a natural circulation test of Hanbit unit 2 was simulated with SPACE code. The major parameters of natural circulation in transient are well predicted in SPACE calculations when compared to the plant data. The SPACE code has sufficient capability to simulate passive cooling phenomena.

  13. Nuclear Facility Accident (NFAC) Unit Test Report For HPAC Version 6.3

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Ronald W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Computational Sciences and Engineering Division; Morris, Robert W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Computational Sciences and Engineering Division; Sulfredge, Charles David [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Computational Sciences and Engineering Division

    2015-12-01

    This is a unit test report for the Nuclear Facility Accident (NFAC) model for the Hazard Prediction and Assessment Capability (HPAC) version 6.3. NFAC’s responsibility as an HPAC component is three-fold. First, it must present an interactive graphical user interface (GUI) by which users can view and edit the definition of an NFAC incident. Second, for each incident defined, NFAC must interact with RTH to create activity table inputs and associate them with pseudo materials to be transported via SCIPUFF. Third, NFAC must create SCIPUFF releases with the associated pseudo materials for transport and dispersion. The goal of NFAC unit testing is to verify that the inputs it produces are correct for the source term or model definition as specified by the user via the GUI.

  14. Another Look at the Draft Mil-Std-1540E Unit Random Vibration Test Requirements

    Science.gov (United States)

    Perl, E.; Peterson, A. J..; Davis, D.

    2012-07-01

    The draft Mil-Std-1540E has been updated to reflect lessons learned since its publication as an SMC Standard in 2008, [1], and an earlier Aerospace Corporation Technical Report released in 2006, [2]. This paper discusses the technical rationale supporting some of the unit random vibration test requirements to provide better insight into their derivation and application to programs. It is intended that these requirements be tailored for each program to reflect the customer risk profile. Several tailoring options are provided and a two phase test strategy is discussed to highlight its applicability to utilizing heritage hardware in new applications.

  15. Potential of alternative sorbents for desulphurization: from laboratory tests to the full-scale combustion unit

    Energy Technology Data Exchange (ETDEWEB)

    Zbyszek Szeliga; Dagmar Juchelkova; Bohumir Cech; Pavel Kolat; Franz Winter; Adam J. Campen; Tomasz S. Wiltowski [Technical University of Ostrava (VSB), Ostrava (Czech Republic). Department of Energy Engineering

    2008-09-15

    At present, natural limestone is used for the desulphurization of waste gases from the combustion of fossil fuels. However, it is important to save all primary resources, such as limestone, for the future. The researchers focused on finding alternative sorbents for the purpose of desulphurization in a dry additive method, which would become the alternative for natural limestone. This paper is primarily focused on desulphurization tests of selected substances. Tests were initially conducted on the laboratory scale, followed by pilot and full-scale combustion units. 15 refs., 9 figs., 5 tabs.

  16. Drug testing and flow cytometry analysis on a large number of uniform sized tumor spheroids using a microfluidic device

    Science.gov (United States)

    Patra, Bishnubrata; Peng, Chien-Chung; Liao, Wei-Hao; Lee, Chau-Hwang; Tung, Yi-Chung

    2016-02-01

    Three-dimensional (3D) tumor spheroid possesses great potential as an in vitro model to improve predictive capacity for pre-clinical drug testing. In this paper, we combine advantages of flow cytometry and microfluidics to perform drug testing and analysis on a large number (5000) of uniform sized tumor spheroids. The spheroids are formed, cultured, and treated with drugs inside a microfluidic device. The spheroids can then be harvested from the device without tedious operation. Due to the ample cell numbers, the spheroids can be dissociated into single cells for flow cytometry analysis. Flow cytometry provides statistical information in single cell resolution that makes it feasible to better investigate drug functions on the cells in more in vivo-like 3D formation. In the experiments, human hepatocellular carcinoma cells (HepG2) are exploited to form tumor spheroids within the microfluidic device, and three anti-cancer drugs: Cisplatin, Resveratrol, and Tirapazamine (TPZ), and their combinations are tested on the tumor spheroids with two different sizes. The experimental results suggest the cell culture format (2D monolayer vs. 3D spheroid) and spheroid size play critical roles in drug responses, and also demonstrate the advantages of bridging the two techniques in pharmaceutical drug screening applications.

  17. Measured Test-Driven Development: Using Measures to Monitor and Control the Unit Development

    Directory of Open Access Journals (Sweden)

    Y. Dubinsky

    2007-01-01

    Full Text Available We analyze Test Driven Development (TDD from cognitive and social perspectives. Based on our analysis, we suggest a technique for controlling and monitoring the TDD process by examining measures that relate to the size and complexity of both code and tests. We call this approach Measured TDD. The motivation for TDD arose from practitioners' tendency to rush into code production, skipping the required testing needed to manufacture quality products. The motivation for Measured TDD is based on difficulties encountered by practitioners in applying TDD. Specifically, with the need to frequently refactor the unit, after every few test and code steps have been performed. We found that the suggested technique enables developers to gain better control over the development process.

  18. How useful are the "other" semipermeable membrane devices (SPMDs); the mini-unit (15.2 cm long)?

    Science.gov (United States)

    Goodbred, Steven L.; Bryant, Wade L.; Rosen, Michael R.; Alvarez, David; Spencer, Terri

    2009-01-01

    Mini (15.2 cm) semipermeable membrane devices (SPMDs) were used successfully in 169 streams from six metropolitan areas of the US to sequester hydrophobic organic compounds (HOCs) that are indicative of urbanization. A microscale assay the P450RGS, which responds to compounds that bind to the aryl hydrocarbon receptor (AhR), and the Fluoroscan, a chemical screen for polycyclic aromatic hydrocarbons (PAHs), were performed on each mini SPMD extract. Results show both tests were sensitive enough to respond in streams with low urbanization and responded exponentially in a predictable way to a gradient of urbanization. Mini SPMDs had sufficient sampling rates to detect HOCs using gas chromatography with mass spectrometric detection (GC/MS) in streams with low levels of urbanization. The total number of HOCs in streams had a linear response to a gradient of urbanization, where 73 of 140 targeted compounds were detected. A diverse group of compounds was found in urban streams including, PAHs, insecticides, herbicides, musk fragrances, waste water treatment compounds and flame retardants. Pentachloroanisole (PCA), a breakdown product of pentachlorophenol (wood preservative), was the most ubiquitous HOC, and was detected in 71% of streams. An evaluation of mini SPMD performance showed they can detect concentrations in water below toxicity benchmarks for many HOCs with the exception of 2,3,7,8 tetrachlorodibenzo-p-dioxin. A comparison of mini SPMDs with full sized (91.4 cm) SPMDs showed they have several distinct advantages. The most notable advantages are their low cost, small size, and reduced chance of vandalism. The greatest limitation is the inability to detect compounds at low concentrations (pg/L). Mini SPMDs perform quite well in a wide array of environmental settings and applications and should be considered as an option in environmental studies.

  19. Testing and Results of Vacuum Swing Adsorption Units for Spacesuit Carbon Dioxide and Humidity Control

    Science.gov (United States)

    McMillin, Summer; Broerman, Craig; Swickrath, Mike; Anderson, Molly

    2010-01-01

    A principal concern for extravehicular activity (EVA) space suits is the capability to control carbon dioxide (CO2) and humidity (H2O) for the crewmember. The release of CO2 in a confined or unventilated area is dangerous for human health and leads to asphyxiation; therefore, CO2 and H2O become leading factors in the design and development of the spacesuit. An amine-based CO2 and H2O vapor sorbent for use in pressure-swing re-generable beds has been developed by Hamilton Sundstrand. The application of solid-amine materials with vacuum swing adsorption technology has shown the capacity to concurrently manage CO2 and H2O levels through a fully regenerative cycle eliminating mission constraints imposed with non-regenerative technologies. Two prototype solid amine-based systems, known as rapid cycle amine (RCA), were designed to continuously remove CO2 and H2O vapor from a flowing ventilation stream through the use of a two-bed amine based, vacuum-swing adsorption system. The Engineering and Science Contract Group (ESCG) RCA is the first RCA unit implementing radial flow paths, whereas the Hamilton Sundstrand RCA was designed with linear flow paths. Testing was performed in a sea-level pressure environment and a reduced-pressure environment with simulated human metabolic loads in a closed-loop configuration. This paper presents the experimental results of laboratory testing for a full-size and a sub-scale test article. The testing described here characterized and evaluated the performance of each RCA unit at the required Portable Life Support Subsystem (PLSS) operating conditions. The test points simulated a range of crewmember metabolic rates. The experimental results demonstrate the ability of each RCA unit to sufficiently remove CO2 and H2O from a closed loop ambient or subambient atmosphere.

  20. A novel passive left heart platform for device testing and research.

    Science.gov (United States)

    Leopaldi, A M; Vismara, R; van Tuijl, S; Redaelli, A; van de Vosse, F N; Fiore, G B; Rutten, M C M

    2015-04-01

    Integration of biological samples into in vitro mock loops is fundamental to simulate real device's operating conditions. We developed an in vitro platform capable of simulating the pumping function of the heart through the external pressurization of the ventricle. The system consists of a fluid-filled chamber, in which the ventricles are housed and sealed to exclude the atria from external loads. The chamber is connected to a pump that drives the motion of the ventricular walls. The aorta is connected to a systemic impedance simulator, and the left atrium to an adjustable preload. The platform reproduced physiologic hemodynamics, i.e. aortic pressures of 120/80 mmHg with 5 L/min of cardiac output, and allowed for intracardiac endoscopy. A pilot study with a left ventricular assist device (LVAD) was also performed. The LVAD was connected to the heart to investigate aortic valve functioning at different levels of support. Results were consistent with the literature, and high speed video recordings of the aortic valve allowed for the visualization of the transition between a fully opening valve and a permanently closed configuration. In conclusion, the system showed to be an effective tool for the hemodynamic assessment of devices, the simulation of surgical or transcatheter procedures and for visualization studies. Copyright © 2015 IPEM. Published by Elsevier Ltd. All rights reserved.

  1. 电磁感应加热试验研究%Study on Test of Electromagnetic Induction Heating Device

    Institute of Scientific and Technical Information of China (English)

    冯晓明

    2015-01-01

    通过感应加热实验研究,介绍新型热处理技术在加氢反应器焊后热处理中的应用,对其在实验过程中遇到的问题做出分析和探讨。%The paper proposes a new heat treatment technology for the post-welding heat treatment of hydrogenation reactors on the basis of the study on the test of an electromagnetic induction heating device and discusses the problems that arose during the test.

  2. Implementation of a Peltier-based cooling device for localized deep cortical deactivation during in vivo object recognition testing

    Science.gov (United States)

    Marra, Kyle; Graham, Brett; Carouso, Samantha; Cox, David

    2012-02-01

    While the application of local cortical cooling has recently become a focus of neurological research, extended localized deactivation deep within brain structures is still unexplored. Using a wirelessly controlled thermoelectric (Peltier) device and water-based heat sink, we have achieved inactivating temperatures (8 mm) than previously reported. After implanting the device into Long Evans rats' basolateral amygdala (BLA), an inhibitory brain center that controls anxiety and fear, we ran an open field test during which anxiety-driven behavioral tendencies were observed to decrease during cooling, thus confirming the device's effect on behavior. Our device will next be implanted in the rats' temporal association cortex (TeA) and recordings from our signal-tracing multichannel microelectrodes will measure and compare activated and deactivated neuronal activity so as to isolate and study the TeA signals responsible for object recognition. Having already achieved a top performing computational face-recognition system, the lab will utilize this TeA activity data to generalize its computational efforts of face recognition to achieve general object recognition.

  3. 78 FR 47011 - Software Unit Testing for Digital Computer Software Used in Safety Systems of Nuclear Power Plants

    Science.gov (United States)

    2013-08-02

    ... COMMISSION Software Unit Testing for Digital Computer Software Used in Safety Systems of Nuclear Power Plants..., ``Software Unit Testing for Digital Computer Software Used in Safety Systems of Nuclear Power Plants.'' This... software elements if those systems include software. This RG is one of six RG revisions addressing...

  4. ThermaCELL and OFF! Clip-On Devices Tested for Repellency and Mortality Against Amblyomma americanum (Acari: Ixodida: Amblyommidae).

    Science.gov (United States)

    Bibbs, Christopher S; Xue, Rui-De

    2016-07-01

    The ThermaCELL with allethrin and OFF! Clip-on with metofluthrin were tested in a 939 m(2) vented enclosure against nymphal lone star ticks, Amblyomma americanum (L.). Repellency assays were conducted at varying distances relative to product specifications for repellency range. Nymphal ticks acclimated for 24 h in chambers attached to 10 repellency tracks per repetition. Devices were turned on, and the tick travel distance and delay until beginning to travel were recorded. Mortality of ticks was recorded after 24 h. Mortality assays were also conducted at the same distances with five ticks per cage, and 12 cages per distance radially distributed around a device. Cages were removed after 5 min, 15 min, 30 min, and 60 min of exposure and checked after 24 h for mortality. Significant travel distance was found when exposed to the ThermaCELL and OFF! Clip-on at their shortest test distances. Significant mortality also resulted at the same distances. Ticks exposed to active devices for longer than 15 min had significant mortality at the shortest distance for OFF! Clip-on and multiple distances for the ThermaCELL. Overall, the spatial repellent devices ThermaCELL with allethrin and OFF! Clip-on with metofluthrin both demonstrated desirable effects when tested against A. americanum nymphs. © The Authors 2016. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  5. Efficacy of a Low Dose of Hydrogen Peroxide (Peroxy Ag+ for Continuous Treatment of Dental Unit Water Lines: Challenge Test with Legionella pneumophila Serogroup 1 in a Simulated Dental Unit Waterline

    Directory of Open Access Journals (Sweden)

    Savina Ditommaso

    2016-07-01

    Full Text Available This study was designed to examine the in vitro bactericidal activity of hydrogen peroxide against Legionella. We tested hydrogen peroxide (Peroxy Ag+ at 600 ppm to evaluate Legionella survival in a simulated dental treatment water system equipped with Water Hygienization Equipment (W.H.E. device that was artificially contaminated. When Legionella pneumophila serogroup (sg 1 was exposed to Peroxy Ag+ for 60 min we obtained a two decimal log reduction. High antimicrobial efficacy was obtained with extended periods of exposure: four decimal log reduction at 75 min and five decimal log reduction at 15 h of exposure. Involving a simulation device (Peroxy Ag+ is flushed into the simulation dental unit waterlines (DUWL we obtained an average reduction of 85% of Legionella load. The product is effective in reducing the number of Legionella cells after 75 min of contact time (99.997% in the simulator device under test conditions. The Peroxy Ag+ treatment is safe for continuous use in the dental water supply system (i.e., it is safe for patient contact, so it could be used as a preventive option, and it may be useful in long-term treatments, alone or coupled with a daily or periodic shock treatment.

  6. Efficacy of a Low Dose of Hydrogen Peroxide (Peroxy Ag⁺) for Continuous Treatment of Dental Unit Water Lines: Challenge Test with Legionella pneumophila Serogroup 1 in a Simulated Dental Unit Waterline.

    Science.gov (United States)

    Ditommaso, Savina; Giacomuzzi, Monica; Ricciardi, Elisa; Zotti, Carla M

    2016-07-22

    This study was designed to examine the in vitro bactericidal activity of hydrogen peroxide against Legionella. We tested hydrogen peroxide (Peroxy Ag⁺) at 600 ppm to evaluate Legionella survival in a simulated dental treatment water system equipped with Water Hygienization Equipment (W.H.E.) device that was artificially contaminated. When Legionella pneumophila serogroup (sg) 1 was exposed to Peroxy Ag⁺ for 60 min we obtained a two decimal log reduction. High antimicrobial efficacy was obtained with extended periods of exposure: four decimal log reduction at 75 min and five decimal log reduction at 15 h of exposure. Involving a simulation device (Peroxy Ag⁺ is flushed into the simulation dental unit waterlines (DUWL)) we obtained an average reduction of 85% of Legionella load. The product is effective in reducing the number of Legionella cells after 75 min of contact time (99.997%) in the simulator device under test conditions. The Peroxy Ag⁺ treatment is safe for continuous use in the dental water supply system (i.e., it is safe for patient contact), so it could be used as a preventive option, and it may be useful in long-term treatments, alone or coupled with a daily or periodic shock treatment.

  7. Efficacy of a Low Dose of Hydrogen Peroxide (Peroxy Ag+) for Continuous Treatment of Dental Unit Water Lines: Challenge Test with Legionella pneumophila Serogroup 1 in a Simulated Dental Unit Waterline

    Science.gov (United States)

    Ditommaso, Savina; Giacomuzzi, Monica; Ricciardi, Elisa; Zotti, Carla M.

    2016-01-01

    This study was designed to examine the in vitro bactericidal activity of hydrogen peroxide against Legionella. We tested hydrogen peroxide (Peroxy Ag+) at 600 ppm to evaluate Legionella survival in a simulated dental treatment water system equipped with Water Hygienization Equipment (W.H.E.) device that was artificially contaminated. When Legionella pneumophila serogroup (sg) 1 was exposed to Peroxy Ag+ for 60 min we obtained a two decimal log reduction. High antimicrobial efficacy was obtained with extended periods of exposure: four decimal log reduction at 75 min and five decimal log reduction at 15 h of exposure. Involving a simulation device (Peroxy Ag+ is flushed into the simulation dental unit waterlines (DUWL)) we obtained an average reduction of 85% of Legionella load. The product is effective in reducing the number of Legionella cells after 75 min of contact time (99.997%) in the simulator device under test conditions. The Peroxy Ag+ treatment is safe for continuous use in the dental water supply system (i.e., it is safe for patient contact), so it could be used as a preventive option, and it may be useful in long-term treatments, alone or coupled with a daily or periodic shock treatment. PMID:27455299

  8. Functional testing of space flight induced changes in tonic motor control by using limb-attached excitation and load devices

    Science.gov (United States)

    Gallasch, Eugen; Kozlovskaya, Inessa

    2007-02-01

    Long term space flights induce atrophy and contractile changes on postural muscles such effecting tonic motor control. Functional testing of tonic motor control structures is a challenge because of the difficulties to deliver appropriate test forces on crew members. In this paper we propose two approaches for functional testing by using limb attached loading devices. The first approach is based on a frequency and amplitude controllable moving magnet exciter to deliver sinusoidal test forces during limb postures. The responding limb deflection is recorded by an embedded accelerometer to obtain limb impedance. The second approach is based on elastic limb loading to evoke self-excited oscillations during arm extensions. Here the contraction force at the oscillation onset provides information about limb stiffness. The rationale for both testing approaches is based on Feldman's λ-model. An arm expander based on the second approach was probed in a 6-month MIR space flight. The results obtained from the load oscillations, confirmed that this device is well suited to capture space flight induced neuromuscular changes.

  9. Liquid-based cytology test use by office-based physicians: United States, 2006-2007.

    Science.gov (United States)

    Hing, Esther; Saraiya, Mona; Roland, Katherine B

    2011-06-01

    In the United States, liquid-based cytology (LBC) has become a common screening method for cervical cancer. However, the extent of LBC use, and how it varies by patient and practice characteristics, is unknown. This report describes the ordering and provision of Papanicolaou (Pap) tests, with a major focus on the extent to which LBC has supplanted conventional cytology. The type of Pap test is examined for visits made to primary care physicians in 2006-2007 by females aged 15-64. Estimates of Pap test cytology use (both LBC and conventional) are based on combined data from the 2006-2007 National Ambulatory Medical Care Survey (NAMCS), an annual nationally representative survey of visits to nonfederal office-based physicians in the United States, as well as on information reported by sample physicians in Cervical Cancer Screening Supplements fielded as part of NAMCS during the same years. In 2006-2007, LBC was used in approximately 75% of Pap tests for which the type of cytology was known. LBC was less likely to be used for Medicare patients than for privately insured patients, although LBC use did not vary significantly according to the other patient or practice characteristics examined. The high percentage of LBC use by office-based physicians in 2006-2007 confirms the widespread use of this screening method among primary care providers, as has been reported in the literature.

  10. Full-scale performance testing and evaluation of unitized curtain walls

    Directory of Open Access Journals (Sweden)

    E. Ilter

    2015-06-01

    Full Text Available Unitized curtain wall systems have been widely seen on high-rise buildings’ facades by bringing benefits with regard to ease of construction, lightness, etc. However, some design and application problems related to structural and infiltration performance of a facade system might arise during its life cycle, which is difficult for the building to compensate. This paper presents a comparative analysis of the structural and infiltration performance of the two identically detailed and produced unitized curtain wall system mock-ups. In order to understand long-term environmental effects on the curtain wall system, a fatigue process was applied on one system in addition to the standard test procedures, while the standard test procedure was applied on the other reference specimen. The tests on the two identical specimens were conducted in accordance with TS EN 13830 and AAMA 501.4 Standards. As a result of air infiltration and wind load resistance tests, air infiltration and frontal deflection values on the facade surface were obtained. Hence, experimental performance of the systems was compared and the effect of the fatigue procedure on the facade performance was evaluated.  

  11. Groundwater Monitoring Report Central Nevada Test Area, Corrective Action Unit 443

    Energy Technology Data Exchange (ETDEWEB)

    None

    2008-04-01

    This report presents the 2007 groundwater monitoring results collected by the U.S. Department of Energy (DOE) Office of Legacy Management (LM) for the Central Nevada Test Area (CNTA) Corrective Action Unit (CAU) 443. Responsibility for the environmental site restoration of the CNTA was transferred from the DOE Office of Environmental Management (DOE-EM) to DOE-LM on October 1, 2006. Requirements for CAU 443 are specified in the Federal Facility Agreement and Consent Order (FFACO 2005) entered into by DOE, the U.S. Department of Defense, and the State of Nevada and includes groundwater monitoring in support of site closure. This is the first groundwater monitoring report prepared by DOE-LM for the CNTA The CNTA is located north of U.S. Highway 6, approximately 30 miles north of Warm Springs in Nye County, Nevada (Figure 1). Three emplacement boreholes, UC-1, UC-3, and UC-4, were drilled at the CNTA for underground nuclear weapons testing. The initial underground nuclear test, Project Faultless, was conducted in borehole UC-1 at a depth of 3,199 feet (ft) (975 meters) below ground surface on January 19, 1968. The yield of the Project Faultless test was estimated to be 0.2 to 1 megaton (DOE 2004). The test resulted in a down-dropped fault block visible at land surface (Figure 2). No further testing was conducted at the CNTA, and the site was decommissioned as a testing facility in 1973.

  12. False positive hepatitis C antibody test results in left ventricular assist device recipients: increased risk with age and transfusions

    Science.gov (United States)

    Lee, Doreen; Colovai, Adriana; Levy, Dana; Vasovic, Ljiljana; Roach, Keith W.; Shuter, Jonathan; Goldstein, Daniel; D’Alessandro, David; Jorde, Ulrich P.; Muggia, Victoria A.

    2017-01-01

    Left ventricular assist devices (LVADs) have been successfully used in patients with heart failure. However, LVADs may trigger immune activation, leading to higher frequencies of autoantibodies. We describe the clinical, epidemiological, and laboratory characteristics of LVAD recipients with false positive hepatitis C (FPHC) serology among 39 consecutive adult LVAD recipients who bridged to heart transplantation from January 2007 to January 2013 at Montefiore Medical Center. FPHC patients were identified as those with post-LVAD positive hepatitis C ELISA antibody tests and negative confirmatory testing with hepatitis C RNA PCR and/or radioimmunoblot assay. Ten (26%) patients previously seronegative for hepatitis C were found to have FPHC after device placement. Of the 39 patients, 32 had HeartMate II devices. The mean age at LVAD placement was 55 years. FPHC correlated with older age at the time of LVAD implantation and with receipt of packed red blood cell transfusions, but not with gender, fresh frozen plasma transfusions, panel reactive antibodies, globulin fraction, rheumatoid factor, or anticardiolipin antibodies. Clinicians should be aware of this increased risk of FPHC in older LVAD patients and those more heavily transfused in order to avoid unnecessary apprehension and possible delay in transplantation. Further studies should be done to evaluate the possible relationship between transfused blood products and immunomodulation. PMID:28203425

  13. Advanced Accelerated Power Cycling Test for Reliability Investigation of Power Device Modules

    DEFF Research Database (Denmark)

    Choi, Uimin; Jørgensen, Søren; Blaabjerg, Frede

    2016-01-01

    of tested power IGBT module. The various realistic electrical operating conditions close to real three-phase converter applications can be achieved by the simple control method. Further, by the proposed concept of applying the temperature stress, it is possible to apply various magnitudes of temperature......This paper presents an apparatus and methodology for an advanced accelerated power cycling test of insulated-gate bipolar transistor (IGBT) modules. In this test, the accelerated power cycling test can be performed under more realistic electrical operating conditions with online wear-out monitoring...... power cycling test setup is given. Then, an improved in situ junction temperature estimation method using on-state collector–emitter voltage VCE ON and load current is proposed. In addition, a procedure of advanced accelerated power cycling test and test results with 600 V, 30 A transfer molded IGBT...

  14. Summary of inspection findings of licensee inservice testing programs at United States commercial nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Dunlop, A.; Colaccino, J.

    1996-12-01

    Periodic inspections of pump and valve inservice testing (IST) programs in United States commercial nuclear power plants are performed by Nuclear Regulatory Commission (NRC) Regional Inspectors to verify licensee regulatory compliance and licensee commitments. IST inspections are conducted using NRC Inspection Procedure 73756, {open_quotes}Inservice Testing of Pumps and Valves{close_quotes} (IP 73756), which was updated on July 27, 1995. A large number of IST inspections have also been conducted using Temporary Instruction 2515/114, {open_quotes}Inspection Requirements for Generic Letter 89-04, Acceptable Inservice Testing Programs{close_quotes} (TI-2515/114), which was issued January 15, 1992. A majority of U.S. commercial nuclear power plants have had an IST inspection to either IP 73756 or TI 2515/114. This paper is intended to summarize the significant and recurring findings from a number of these inspections since January of 1990.

  15. Modeling and experimental testing activity of the Voltage Optimization Unit

    DEFF Research Database (Denmark)

    Zecchino, Antonio; Hu, Junjie; Marinelli, Mattia

    cost investments of to the system operator, thus a proactive tap algorithm is developed and tested in this project, relying on local measurements. In addition, we also compared the experimental result with the one simulated in the DigSilent PowerFactory software environment (the software used...... the voltage problems in presence of photovoltaic distributed generation, using Bistrup distribution grid (DONG Energy) as a test case. This second report presents the experimental results of the testing activity of the Voltage Optimization Unit (VOU), i.e., a distribution transformer with single-phase on......-load tap changers (OLTC) in an experimental low voltage grid. Both the transformer internal behavior and its effective operations under different unbalanced bidirectional power flow conditions have been investigated. Moreover, different control logics are analyzed based on their control objectives and control...

  16. Modeling and Experimental Tests of a Mechatronic Device to Measure Road Profiles Considering Impact Dynamics

    DEFF Research Database (Denmark)

    Souza, A.; Santos, Ilmar

    2002-01-01

    profile by means of gravitational and spring forces. Accelerometers are attached above the rolling wheels and the wheels follow the profiles of a rough ground. After integrating the acceleration signal twice and measuring the vehicle displacement the road profiles can be achieved. It is important...... to highlight that the aim of this device is to independently measure two road profiles, without the influence of the vehicle dynamics where the mechanism is attached. Before the mechatronic mechanism is attached to a real vehicle, its dynamic behavior must be known. A theoretical analysis of the mechanism...

  17. A Complete Automation of Unit Testing for JavaScript Programs

    Directory of Open Access Journals (Sweden)

    M. Alshraideh

    2008-01-01

    Full Text Available Problem statement: Program testing is expensive and labor intensive, often consuming more than half of the total development costs, and yet it is frequently not done well and the results are not always satisfactory. The objective of this paper is to present an automatic test data generation tool that aims to completely automate unit testing of JavaScript functions. The methodology: In order to use the proposed tool, the tester annotates the files that contain the class to be tested. Moreover, the tester must specify the test data coverage criterion to be used, either branch coverage or mutation analysis. However, the tool is then integrated into the JavaScript compiler and test generation is invoked by a command line option. Also, the code to be tested is parsed into an abstract syntax tree from which the test tool generates a program dependency graph for the function under test. However, if mutation analysis coverage is required, the abstract syntax tree for a meta-mutant program is also generated. To provide guidance for the test data search, the function under test instrumented in accordance with the coverage criterion. Branch predicate expressions are always instrumented, in the case of mutation coverage, mutated statements are also instrumented. Compilation then continues from the modified abstract syntax tree to generate instrumented executables that were loaded into the test data search module. Results: The experiment done in our study by using the proposed tool for branch coverage shows that the most effective result for string equality was obtained using the edit distance fitness function, while no significant difference was found in the fitness function for string ordering. Through exhaustive mulation coverage 8% are found to be equivalent. Conclusion: By having a complete automation it reduces the cost of software testing dramatically and also facilitates continuous testing. It is reported that at least 50% of the total software

  18. DESIGN, DEVELOPMENT AND EARLY TESTING OFA DEVICE FOR THE MONITORING OF ZOOTECHNICAL EFFLUENT DISTRIBUTION USING RAINGUN DISTRIBUTION SYSTEMS

    Directory of Open Access Journals (Sweden)

    Fabrizio Mazzetto

    2009-06-01

    Full Text Available The present project consisted in the design, development and early testing of a device for the monitoring of the distribution of zootechnical effluents using raingun distribution systems with the aim of defining a system that is reliable and objective that is useful both in farm management and to certify the activities carried out with respect to environmental regulations. The proposed system leads to the integration of the records of the main operating parameters of the distribution process (flow rate, range, quantity of distributed sewage with those regarding operating times and distance covered by the gun-supporting trolley (measured through a GPS receiver. The main strength of said device lies in its autonomy in terms of power supply: the slurry flowing inside the pipe is used to generate, through a dynamo, an amount of electric power that is sufficient to ensure its operation.

  19. Unit Testing Using Design by Contract and Equivalence Partitions, Extreme Programming and Agile Processes in Software Engineering

    DEFF Research Database (Denmark)

    Madsen, Per

    2003-01-01

    Extreme Programming [1] and in particular the idea of Unit Testing can improve the quality of the testing process. But still programmers need to do a lot of tiresome manual work writing test cases. If the programmers could get some automatic tool support enforcing the quality of test cases then t...... then the overall quality of the software would improve significantly....

  20. Unit Testing Using Design by Contract and Equivalence Partitions, Extreme Programming and Agile Processes in Software Engineering

    DEFF Research Database (Denmark)

    Madsen, Per

    2003-01-01

    Extreme Programming [1] and in particular the idea of Unit Testing can improve the quality of the testing process. But still programmers need to do a lot of tiresome manual work writing test cases. If the programmers could get some automatic tool support enforcing the quality of test cases...

  1. Digital Micromirror Device (DMD-Based High-Cycle Torsional Fatigue Testing Micromachine for 1D Nanomaterials

    Directory of Open Access Journals (Sweden)

    Chenchen Jiang

    2016-03-01

    Full Text Available Fatigue behavior of nanomaterials could ultimately limit their applications in variable nano-devices and flexible nanoelectronics. However, very few existing nanoscale mechanical testing instruments were designed for dedicated fatigue experiments, especially for the challenging torsional cyclic loading. In this work, a novel high-cycle torsion straining micromachine, based on the digital micromirror device (DMD, has been developed for the torsional fatigue study on various one-dimensional (1D nanostructures, such as metallic and semiconductor nanowires. Due to the small footprint of the DMD chip itself and its cable-remote controlling mechanisms, it can be further used for the desired in situ testing under high-resolution optical or electron microscopes (e.g., scanning electron microscope (SEM, which allows real-time monitoring of the fatigue testing status and construction of useful structure-property relationships for the nanomaterials. We have then demonstrated its applications for testing nanowire samples with diameters about 100 nm and 500 nm, up to 1000 nm, and some of them experienced over hundreds of thousands of loading cycles before fatigue failure. Due to the commercial availability of the DMD and millions of micromirrors available on a single chip, this platform could offer a low-cost and high-throughput nanomechanical solution for the uncovered torsional fatigue behavior of various 1D nanostructures.

  2. Proposal of High-Frequency Magnetic Field Immunity Test for Medical Devices, and Design and Development of Coil for the Test

    Science.gov (United States)

    Yamamoto, Takahiko; Koshiji, Kohji

    Medical devices have been obliged to satisfy electromagnetic compatibility by revision of the pharmaceutical affairs law. However, even if the medical devices satisfy the electromagnetic compatibility based on the law, it is not necessarily safe. Sometimes, malfunctions of cardiac pacemaker are caused by the magnetic field leaked from an induction heating cooker. In this paper, a new method of electromagnetic susceptability (EMS) evaluation is proposed, and a loop coil for the magnetic field immunity test in the frequency range from 10kHz to 3MHz is designed and developed. As a result, the loop coil made on an experimental basis generated uniform magnetic field with a fluctuation within 3.3dB in the loop coil pane and 5.6dB along the coil axis.

  3. HIV Testing Among Internet-Using MSM in the United States: Systematic Review.

    Science.gov (United States)

    Noble, Meredith; Jones, Amanda M; Bowles, Kristina; DiNenno, Elizabeth A; Tregear, Stephen J

    2017-02-01

    Regular HIV testing enables early identification and treatment of HIV among at-risk men who have sex with men (MSM). Characterizing HIV testing needs for Internet-using MSM informs development of Internet-facilitated testing interventions. In this systematic review we analyze HIV testing patterns among Internet-using MSM in the United States who report, through participation in an online study or survey, their HIV status as negative or unknown and identify demographic or behavioral risk factors associated with testing. We systematically searched multiple electronic databases for relevant English-language articles published between January 1, 2005 and December 16, 2014. Using meta-analysis, we summarized the proportion of Internet-using MSM who had ever tested for HIV and the proportion who tested in the 12 months preceding participation in the online study or survey. We also identified factors predictive of these outcomes using meta-regression and narrative synthesis. Thirty-two studies that enrolled 83,186 MSM met our inclusion criteria. Among the studies reporting data for each outcome, 85 % (95 % CI 82-87 %) of participants had ever tested, and 58 % (95 % CI 53-63 %) had tested in the year preceding enrollment in the study, among those for whom those data were reported. Age over 30 years, at least a college education, use of drugs, and self-identification as being homosexual or gay were associated with ever having tested for HIV. A large majority of Internet-using MSM indicated they had been tested for HIV at some point in the past. A smaller proportion-but still a majority-reported they had been tested within the year preceding study or survey participation. MSM who self-identify as heterosexual or bisexual, are younger, or who use drugs (including non-injection drugs) may be less likely to have ever tested for HIV. The overall findings of our systematic review are encouraging; however, a subpopulation of MSM may benefit from targeted outreach. These

  4. Closure Plan for Corrective Action Unit 109: U-2bu Subsidence Crater Nevada Test Site, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Shannon Parsons

    1999-03-01

    The U-2bu subsidence crater, Corrective Action Unit 109, will be closed in accordance with the Resource Conservation and Recovery Act, the Nevada Division of Environmental Protection operational permit, and the Federal Facilities Agreement and Consent Order. The U-2bu subsidence crater is located in Area 2 of the Nevada Test Site. It was created in 1971 by an underground nuclear test with the name Miniata. The crater has a diameter of 288 meters (944 feet) and an approximate depth of 35 meters (115 feet). The subsidence crater was used as a land disposal unit for radioactive and hazardous waste from 1973 to 1988. Site disposal history is supported by memorandums, letters, and personnel who worked at the Nevada Test Site at the time of active disposal. Closure activities will include the excavation and disposal of impacted soil form the tip of the crater. Upon completion of excavation, verification samples will be collected to show that lead has been removed to concentrations be low regulatory action level. The area will then be backfilled and a soil flood diversion berm will be constructed, and certified by an independent professional engineer as to having followed the approved Closure Plan.

  5. Design and Test Plans for a Non-Nuclear Fission Power System Technology Demonstration Unit

    Science.gov (United States)

    Mason, Lee; Palac, Donald; Gibson, Marc; Houts, Michael; Warren, John; Werner, James; Poston, David; Qualls, Arthur Lou; Radel, Ross; Harlow, Scott

    2012-01-01

    A joint National Aeronautics and Space Administration (NASA) and Department of Energy (DOE) team is developing concepts and technologies for affordable nuclear Fission Power Systems (FPSs) to support future exploration missions. A key deliverable is the Technology Demonstration Unit (TDU). The TDU will assemble the major elements of a notional FPS with a non-nuclear reactor simulator (Rx Sim) and demonstrate system-level performance in thermal vacuum. The Rx Sim includes an electrical resistance heat source and a liquid metal heat transport loop that simulates the reactor thermal interface and expected dynamic response. A power conversion unit (PCU) generates electric power utilizing the liquid metal heat source and rejects waste heat to a heat rejection system (HRS). The HRS includes a pumped water heat removal loop coupled to radiator panels suspended in the thermal-vacuum facility. The basic test plan is to subject the system to realistic operating conditions and gather data to evaluate performance sensitivity, control stability, and response characteristics. Upon completion of the testing, the technology is expected to satisfy the requirements for Technology Readiness Level 6 (System Demonstration in an Operational and Relevant Environment) based on the use of high-fidelity hardware and prototypic software tested under realistic conditions and correlated with analytical predictions.

  6. Control concept for a hybrid engine test device composed of a water vortex brake and an asynchronous machine; Regelungskonzept fuer einen Hybrid-Motorenpruefstand

    Energy Technology Data Exchange (ETDEWEB)

    Maeenpaeae, A. [ABB Automation Products, Mannheim (Germany); Fischer, G. [Technische Univ. Darmstadt (Germany)

    2000-07-01

    New environmental laws require lower exhaust limits of motor vehicles all over the world. To test these limits, drive-cycle tests are performed on engine test devices. Future laws will require the simulation od downhill driving, which requires extensive changes to the engine test devices. Hybrid test devices with a water vortex brake and an asynchronous machine could be advantageous. A new control concept for those hybrid test devices is described here. (orig.) [German] Neue Umweltgesetze druecken weltweit die Abgasgrenzwerte von Automobilen nach unten. Zur Ueberpruefung dieser Grenzwerte dienen Fahrzyklus-Testreihen auf Motorenpruefstaenden. Kuenftige Vorschriften erfordern dabei bald die Simulation des 'Schiebebetriebs' (wie bei Bergabfahrten). Das erfordert aufwendige Umruestungen bei den Motorenpruefstaenden. Eine preisguenstige Loesung stellen Hybrid-Pruefstaende aus einer Wasserwirbelbremse und einer Asynchron-Maschine dar. Ein neues Regelkonzept dafuer wird hier beschrieben. (orig.)

  7. Testing of the Engineering Model Electrical Power Control Unit for the Fluids and Combustion Facility

    Science.gov (United States)

    Kimnach, Greg L.; Lebron, Ramon C.; Fox, David A.

    1999-01-01

    The John H. Glenn Research Center at Lewis Field (GRC) in Cleveland, OH and the Sundstrand Corporation in Rockford, IL have designed and developed an Engineering Model (EM) Electrical Power Control Unit (EPCU) for the Fluids Combustion Facility, (FCF) experiments to be flown on the International Space Station (ISS). The EPCU will be used as the power interface to the ISS power distribution system for the FCF's space experiments'test and telemetry hardware. Furthermore. it is proposed to be the common power interface for all experiments. The EPCU is a three kilowatt 12OVdc-to-28Vdc converter utilizing three independent Power Converter Units (PCUs), each rated at 1kWe (36Adc @ 28Vdc) which are paralleled and synchronized. Each converter may be fed from one of two ISS power channels. The 28Vdc loads are connected to the EPCU output via 48 solid-state and current-limiting switches, rated at 4Adc each. These switches may be paralleled to supply any given load up to the 108Adc normal operational limit of the paralleled converters. The EPCU was designed in this manner to maximize allocated-power utilization. to shed loads autonomously, to provide fault tolerance. and to provide a flexible power converter and control module to meet various ISS load demands. Tests of the EPCU in the Power Systems Facility testbed at GRC reveal that the overall converted-power efficiency, is approximately 89% with a nominal-input voltage of 12OVdc and a total load in the range of 4O% to 110% rated 28Vdc load. (The PCUs alone have an efficiency of approximately 94.5%). Furthermore, the EM unit passed all flight-qualification level (and beyond) vibration tests, passed ISS EMI (conducted, radiated. and susceptibility) requirements. successfully operated for extended periods in a thermal/vacuum chamber, was integrated with a proto-flight experiment and passed all stability and functional requirements.

  8. Cyclone Boiler Field Testing of Advanced Layered NOx Control Technology in Sioux Unit 1

    Energy Technology Data Exchange (ETDEWEB)

    Marc A. Cremer; Bradley R. Adams

    2006-06-30

    A four week testing program was completed during this project to assess the ability of the combination of deep staging, Rich Reagent Injection (RRI), and Selective Non-Catalytic Reduction (SNCR) to reduce NOx emissions below 0.15 lb/MBtu in a cyclone fired boiler. The host site for the tests was AmerenUE's Sioux Unit 1, a 500 MW cyclone fired boiler located near St. Louis, MO. Reaction Engineering International (REI) led the project team including AmerenUE, FuelTech Inc., and the Electric Power Research Institute (EPRI). This layered approach to NOx reduction is termed the Advanced Layered Technology Approach (ALTA). Installed RRI and SNCR port locations were guided by computational fluid dynamics (CFD) based modeling conducted by REI. During the parametric testing, NOx emissions of 0.12 lb/MBtu were achieved consistently from overfire air (OFA)-only baseline NOx emissions of 0.25 lb/MBtu or less, when firing the typical 80/20 fuel blend of Powder River Basin (PRB) and Illinois No.6 coals. From OFA-only baseline levels of 0.20 lb/MBtu, NOx emissions of 0.12 lb/MBtu were also achieved, but at significantly reduced urea flow rates. Under the deeply staged conditions that were tested, RRI performance was observed to degrade as higher blends of Illinois No.6 were used. NOx emissions achieved with ALTA while firing a 60/40 blend were approximately 0.15 lb/MBtu. NOx emissions while firing 100% Illinois No.6 were approximately 0.165 lb/MBtu. Based on the performance results of these tests, economics analyses of the application of ALTA to a nominal 500 MW cyclone unit show that the levelized cost to achieve 0.15 lb/MBtu is well below 75% of the cost of a state of the art SCR.

  9. Testing and Results of Vacuum Swing Adsorption Units for Spacesuit Carbon Dioxide and Humidity Control

    Science.gov (United States)

    McMillin, Summer D.; Broerman, Craig D.; Swickrath, Michael; Anderson, Molly

    2011-01-01

    A principal concern for extravehicular activity (EVA) spacesuits is the capability to control carbon dioxide (CO2) and humidity (H2O) for the crewmember. The release of CO2 in a confined or unventilated area is dangerous for human health and leads to asphyxiation; therefore, CO2 and H2O control become leading factors in the design and development of the spacesuit. An amine-based CO2 and H2O vapor sorbent for use in pressure-swing regenerable beds has been developed by Hamilton Sundstrand. The application of solidamine materials with vacuum swing adsorption technology has shown the capacity to concurrently manage CO2 and H2O levels through a fully regenerative cycle eliminating mission constraints imposed with nonregenerative technologies. Two prototype solid amine-based systems, known as rapid cycle amine (RCA), were designed to continuously remove CO2 and H2O vapor from a flowing ventilation stream through the use of a two-bed amine based, vacuum-swing adsorption system. The Engineering and Science Contract Group (ESCG) RCA implements radial flow paths, whereas the Hamilton Sundstrand RCA was designed with linear flow paths. Testing was performed in a sea-level pressure environment and a reduced-pressure environment with simulated human metabolic loads in a closed-loop configuration. This paper presents the experimental results of laboratory testing for a full-size and a sub-scale test article. The testing described here characterized and evaluated the performance of each RCA unit at the required Portable Life Support Subsystem (PLSS) operating conditions. The test points simulated a range of crewmember metabolic rates. The experimental results demonstrated the ability of each RCA unit to sufficiently remove CO2 and H2O from a closed loop ambient or sub-ambient atmosphere.

  10. Simulation of sandstone degradation using large-scale slake durability index testing device

    Directory of Open Access Journals (Sweden)

    Chaowarin Walsri

    2012-11-01

    Full Text Available Large-scale slake durability index tests have been performed on Khok Kruat (KK, Phu Kradung (PK and Phra Wihan(PW sandstone. A rotating drum with a diameter of 64 cm and length of 40 cm was fabricated to accommodate ten rockfragments with a nominal size of 10 cm. Both large-scale and standard-testing were performed under dry and wet conditions.The large-scale test yields rock deterioration twice greater than the small-scale test, primarily due to the greater energyimposed on the rock fragments. The weight losses under wet condition are 12%, 8%, and 3% greater than under dry condition for KK, PK, and PW sandstones, respectively. After 10 test cycles the water absorption values for PW, KK and PKsandstones are 12%, 3%, and 2%, respectively. Rock degradation under the rapid cooling-heating cycles in the laboratory isabout 18 times faster than under the field condition in the northeast of Thailand.

  11. Advanced Motor Control Test Facility for NASA GRC Flywheel Energy Storage System Technology Development Unit

    Science.gov (United States)

    Kenny, Barbara H.; Kascak, Peter E.; Hofmann, Heath; Mackin, Michael; Santiago, Walter; Jansen, Ralph

    2001-01-01

    This paper describes the flywheel test facility developed at the NASA Glenn Research Center with particular emphasis on the motor drive components and control. A four-pole permanent magnet synchronous machine, suspended on magnetic bearings, is controlled with a field orientation algorithm. A discussion of the estimation of the rotor position and speed from a "once around signal" is given. The elimination of small dc currents by using a concurrent stationary frame current regulator is discussed and demonstrated. Initial experimental results are presented showing the successful operation and control of the unit at speeds up to 20,000 rpm.

  12. Acoustic emission monitoring of hot functional testing: Watts Bar Unit 1 Nuclear Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Hutton, P.H.; Dawson, J.F.; Friesel, M.A.; Harris, J.C.; Pappas, R.A.

    1984-06-01

    Acoustic emission (AE) monitoring of selected pressure boundary areas at TVA's Watts Bar, Unit 1 Nuclear Power Plant during hot functional preservice testing is described in this report. The report deals with background, methodology, and results. The work discussed here is a major milestone in a program supported by NRC to develop and demonstrate application of AE monitoring for continuous surveillance of reactor pressure boundaries to detect and evaluate growing flaws. The subject work demonstrated that anticipated problem areas can be overcome. Work is continuing toward AE monitoring during reactor operation.

  13. Corrective Action Plan for Corrective Action Unit 490: Station 44 Burn Area, Tonopah Test Range, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    K. B. Campbell

    2002-04-01

    Corrective Action Unit (CAU) 490, Station 44 Burn Area is located on the Tonopah Test Range (TTR). CAU 490 is listed in the Federal Facility Agreement and Consent Order (FFACO, 1996) and includes for Corrective Action Sites (CASs): (1) Fire Training Area (CAS 03-56-001-03BA); (2) Station 44 Burn Area (CAS RG-56-001-RGBA); (3) Sandia Service Yard (CAS 03-58-001-03FN); and (4) Gun Propellant Burn Area (CAS 09-54-001-09L2).

  14. [Ethylene oxide sterilization. II. Influence of test devices on the performance of biological monitors and its evaluation].

    Science.gov (United States)

    Pinto, T de J; Saito, T

    1992-12-01

    In view of the importance of the assurance of the sterility of medical devices, with a large incidence of tubular forms, a study of biological monitors was undertaken, using paper as a carrier, the dimension of the test specimens being the variable considered. After the sterilization process in an industrial cycle, followed by the recovery of the surviving spores through inoculation of the carriers into thioglycolate broth, soybean-casein broth and this last with the addition of bromothymol blue. No differences were found between the growth promoting capacity of these 3 media. The effectiveness of sterilization was dependent on the dimension of the test specimens. The periodic determination of residual gas content on the test specimens, as well as the monitoring of the industrial environment demonstrate the need and importance of the legislation in force.

  15. Exercise physiology, testing, and training in patients supported by a left ventricular assist device.

    Science.gov (United States)

    Loyaga-Rendon, Renzo Y; Plaisance, Eric P; Arena, Ross; Shah, Keyur

    2015-08-01

    The left ventricular assist device (LVAD) is an accepted treatment alternative for the management of end-stage heart failure. As we move toward implantation of LVADs in less severe cases of HF, scrutiny of functional capacity and quality of life becomes more important. Patients demonstrate improvements in exercise capacity after LVAD implantation, but the effect is less than predicted. Exercise training produces multiple beneficial effects in heart failure patients, which would be expected to improve quality of life. In this review, we describe factors that are thought to participate in the persistent exercise impairment in LVAD-supported patients, summarize current knowledge about the effect of exercise training in LVAD-supported patients, and suggest areas for future research.

  16. Modeling and Experimental Tests of a Mechatronic Device to Measure Road Profiles Considering Impact Dynamics

    DEFF Research Database (Denmark)

    Souza, A.; Santos, Ilmar

    2002-01-01

    Vehicles travel at different speeds and, as a consequence, experience a broad spectrum of vibrations. One of the most important source of vehicle vibration is the road profile. Hence the knowledge of the characteristics of a road profile enables engineers to predict the dynamic behavior...... to highlight that the aim of this device is to independently measure two road profiles, without the influence of the vehicle dynamics where the mechanism is attached. Before the mechatronic mechanism is attached to a real vehicle, its dynamic behavior must be known. A theoretical analysis of the mechanism...... the mechanism components. By modeling impacts between a wheel and the road by Newton´s Law, the complete dynamics of the system can be predicted, and the operational range (velocity limits) of the mechanism can be defined based on the mathematical model. Key words: multibody dynamics, impact dynamics and road...

  17. The 5th surveillance testing for Kori unit 1 reactor vessel materials

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Kee Ok; Kim, Byoung Chul; Lee, Sam Lai; Choi, Kwun Jae; Gong, Un Sik; Chang, Jong Hwa; Joo, Yong Sun; Ahn, Sang Bok; Hong, Joon Hwa [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-08-01

    Surveillance testing for reactor vessel materials is performed in order to evaluate the irradiation embrittlement due to neutrons during operation and set the condition of safe operation of nuclear reactor. The 5th surveillance testing was performed primarily by Korea Atomic Energy Research Institute and Westinhouse corporation partially involved in testing and calculation data evaluation in order to obtain reliable test result. Fast neutron fluences for capsule V, T, S, R and P were 5.087E+18, 1.115E+19, 1.228E+19, 2.988E+19, and 3.938E+19n/cm2, respectively. The bias factor, the ratio of calculation/measurement, was 0.940 for the 1st through 5th testing and the calculational uncertainty, 7% satisfied the requirement of USNRC Reg.Guide DG-1053, 20%. The best estimated neutron fluence for reactor vessel inside surface was 1.9846E+19n/cm{sup 2} based on the end of 17th fuel cycle and it was predicted that the fluences of vessel inside surface at 24, 32, 40 and 48EFPY would reach 3.0593E+19, 4.0695E+19, 5.0797E+19 and 6.0900E+19n/cm{sup 2} based on the current calculation. PTS analysis for Kori unit 1 showed that 27.93EFPY was the threshold value for 300 deg F requirement. 71 refs., 33 figs., 52 tabs. (Author)

  18. Unit testing, model validation, and biological simulation [version 1; referees: 2 approved, 1 approved with reservations

    Directory of Open Access Journals (Sweden)

    Gopal P. Sarma

    2016-08-01

    Full Text Available The growth of the software industry has gone hand in hand with the development of tools and cultural practices for ensuring the reliability of complex pieces of software. These tools and practices are now acknowledged to be essential to the management of modern software. As computational models and methods have become increasingly common in the biological sciences, it is important to examine how these practices can accelerate biological software development and improve research quality. In this article, we give a focused case study of our experience with the practices of unit testing and test-driven development in OpenWorm, an open-science project aimed at modeling Caenorhabditis elegans. We identify and discuss the challenges of incorporating test-driven development into a heterogeneous, data-driven project, as well as the role of model validation tests, a category of tests unique to software which expresses scientific models.

  19. Test-bed for compact ventilation units; Pruefstand fuer Kompaktlueftungsgeraete fuer Komfortlueftung

    Energy Technology Data Exchange (ETDEWEB)

    Furter, R.; Helfenfinger, D.; Huber, H.; Wenger, L.

    2005-12-15

    This comprehensive, illustrated report for the Swiss Federal Office of Energy (SFOE) by the University of Applied Sciences in Lucerne, Switzerland takes a look at the testing facility at the university that is used to test compact ventilation systems. These feature heat-recovery and return-air heat-pumps and are used in housing built to low energy-consumption standards such as the Swiss 'Minergie' and 'Minergie-P' standards. The primary goal is a technically comprehensive testing programme for compact ventilation units with heat recovery and heat pumps, which can nevertheless be carried out at reasonable cost. In addition to thermal and flow measurements, acoustic measurements are also carried out. The authors quote that the overall assessment provided can also include service and maintenance, materials used and possible problems with thermal bridges. The test installation is described and the testing regulations used are elaborated, as are the various factors that can be measured and examined. First results are presented and a review of work to be done at the European level is discussed.

  20. Detecting and isolating faults of an air-handling unit using on- line diagnostic tests

    Energy Technology Data Exchange (ETDEWEB)

    Pakanen, J. [VTT Building Technology, Espoo (Finland). Building Services and Fire Technology

    1996-12-31

    On-line diagnostic testing is one choice, when practical and robust fault detection and isolation methods are considered for automated processes. Performing a test means exciting a process by means of prescribed input signals, supervising responses and comparing results with a process model. An on-line diagnostic test is repeated similarly every time, in similar process conditions, making modelling an uncomplicated task. Fault detection is a direct consequence of the comparison, but fault isolation is based on elementary constraints, decomposed from the process model. A rough description of a fault can be achieved by heuristic reasoning, which enables application of the method in practice. A more specified fault description is accomplished by learning from old solutions. The reasoner accumulates information making decisions of the classifier gradually more precise through acquired experience. The method is best for successive installations, in which knowledge can be cumulated. On-line diagnostic tests are generic in character, but in this paper they are configured for an air handling unit of an office building and applied in its preheating subprocess. The paper presents the development, simulation and field tests of the fault detection and isolation method and its configuration as a part of a diagnostic system. (orig.) (35 refs.)

  1. The shock tube as a device for testing transonic airfoils at high Reynolds numbers

    Science.gov (United States)

    Cook, W. J.; Presley, L. L.; Chapman, G. T.

    1978-01-01

    A performance analysis of gas-driven shock tubes shows that transonic airfoil flows with chord Reynolds numbers in the range of 100 million can be generated behind the primary shock in a large shock tube. A study of flow over simple airfoils has been carried out at low and intermediate Reynolds numbers to assess the testing technique. Results obtained from schlieren photos and airfoil pressure measurements show that steady transonic flows similar to those observed for the airfoils in wind tunnels can be generated within the available testing time in a shock tube with either properly-contoured test section walls or a properly-designed slotted-wall test section. The study indicates that the shock tube is a useful facility for studying two-dimensional high Reynolds number transonic airfoil flows.

  2. A MEMS Device for in-situ TEM Test of SCS Nanobeam

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    In-situ tensile testing in TEM (transmission electron microscopy) is a useful tool for studying mechanical properties of nano-structures because it can provide quanti-tative information on sample deformation at atomic scale. To facilitate in-situ TEM tensile tests of SCS (single crystal silicon) nanobeam, a MEMS tensile-testing chip was designed and fabricated. The chip was fabricated by means of bulk micro-machining and wafer bonding techniques. An SCS nanobeam, a comb drive ac-tuator, a force sensor beam and an electron beam window were integrated into the chip. With the on-chip comb-drive-actuator stretching the nanobeam and in-situ TEM observation, tensile test on a 90 nm-thick nanobeam was performed and the strain-stress relationship was obtained. The Young’s modulus was fitted to be 161 GPa and did not show the size effect.

  3. Additional collection devices used in conjunction with the SurePath Liquid-Based Pap Test broom device do not enhance diagnostic utility

    Directory of Open Access Journals (Sweden)

    O'Connor Jason C

    2004-09-01

    Full Text Available Abstract Background We have previously shown that use of an EC brush device in combination with the Rovers Cervex-Brush (SurePath broom offered no significant improvement in EC recovery. Here we determine if use of additional collection devices enhance the diagnostic utility of the SurePath Pap for gynecologic cytology. Methods After informed consent, 37 women ages 18–56 receiving their routine cervical examinations were randomized into four experimental groups. Each group was first sampled with the SurePath broom then immediately re-sampled with an additional collection device or devices. Group 1: Rover endocervix brush (n = 8. Group 2: Medscand CytoBrush Plus GT (n = 7. Group 3: Rover spatula + endocervix brush (n = 11. Group 4: Medscand spatula + CytoBrush Plus GT (n = 11. Results Examination of SurePath broom-collected cytology yielded the following abnormal diagnoses: atypia (n = 2, LSIL (n = 5 and HSIL (n = 3. Comparison of these diagnoses to those obtained from paired samples using the additional collection devices showed that use of a second and or third device yielded no additional abnormal diagnoses. Importantly, use of additional devices did not improve upon the abnormal cell recovery of the SurePath broom and in 4/10 cases under-predicted or did not detect the SurePath broom-collected lesion as confirmed by cervical biopsy. Finally, in 36/37 cases, the SurePath broom successfully recovered ECs. Use of additional devices, in Group 3, augmented EC recovery to 37/37. Conclusions Use of additional collection devices in conjunction with the SurePath broom did not enhance diagnostic utility of the SurePath Pap. A potential but not significant improvement in EC recovery might be seen with the use of three devices.

  4. Validity of purchasing power parity for selected Latin American countries: Linear and non-linear unit root tests

    Directory of Open Access Journals (Sweden)

    Claudio Roberto Fóffano Vasconcelos

    2016-01-01

    Full Text Available The aim of this study is to examine empirically the validity of PPP in the context of unit root tests based on linear and non-linear models of the real effective exchange rate of Argentina, Brazil, Chile, Colombia, Mexico, Peru and Venezuela. For this purpose, we apply the Harvey et al. (2008 linearity test and the non-linear unit root test (Kruse, 2011. The results show that the series with linear characteristics are Argentina, Brazil, Chile, Colombia and Peru and those with non-linear characteristics are Mexico and Venezuela. The linear unit root tests indicate that the real effective exchange rate is stationary for Chile and Peru, and the non-linear unit root tests evidence that Mexico is stationary. In the period analyzed, the results show support for the validity of PPP in only three of the seven countries.

  5. The 5th surveillance testing for Kori unit 2 reactor vessel materials

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Kee Ok; Kim, Byoung Chul; Lee, Sam Lai; Choi, Kwon Jae; Gong, Un Sik; Chang, Jong Hwa; Joo, Yong Sun; Ahn, Sang Bok; Hong, Joon Hwa [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2001-03-01

    Surveillance testing for reactor vessel materials is performed in order to evaluate the irradiation embrittlement due to neutrons during operation and set the condition of safe operation of nuclear reactor. The 5th surveillance testing was performed completely by Korea Atomic Energy Research Institute at Taejeon after the capsule was transported from Kori site including its removal from reactor. Fast neutron fluences for capsules were calculated and various testing including mechanical and chemistry analysis were performed in order to evaluate the integrity of Kori unit 2 reactor vessel during the operation until life time. The evaluation results are as follows; Fast neutron fluences for capsules V, R, P, T and N are 2.837E+18, 1.105E+19, 2.110E+19, 3.705E+19 and 4.831E+19n/cm{sup 2}, respectively. The bias factor, the ratio of measurement/calculation, was 0.918 for the 1st through 5th testing and the calculational uncertainty, 11.6% satisfied the requirement of USNRC Reg.Guide DG-1053, 20%. The best estimated neutron fluence for reactor vessel inside surface was 1.898E+19n/cm{sup 2} based on the end of 15th fuel cycle and it was predicted that the fluences of vessel inside surface at 32, 40, 48 and 56EFPY would reach 4.203E+19, 5.232E+19, 6.262E+19 and 7.291E+19n/cm{sup 2} based on the current calculation. The result through this analysis for Kori unit 2 showed that there would be no problem for the pressurized thermal shock(PTS) during the operation until design life. 49 refs., 35 figs., 48 tabs. (Author)

  6. The 4th surveillance testing for Kori unit 3 reactor vessel materials

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Kee Ok; Kim, Byoung Chul; Lee, Sam Lai; Choi, Kwun Jae; Gong, Un Sik; Chang, Jong Hwa; Joo, Yong Sun; Ahn, Sang Bok; Hong, Joon Hwa [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-10-01

    Surveillance testing for reactor vessel materials is performed in order to evaluate the irradiation embrittlement due to neutrons during operation and set the condition of safe operation of nuclear reactor. The 4th surveillance testing was performed completely by Korea Atomic Energy Research Institute at Taejeon after the capsule was transported from Kori site including its removal from reactor. Fast neutron fluences for capsules were calculated and various testing including mechanical and chemistry analysis were performed in order to evaluate the integrity of Kori unit 3 reactor vessel during the operation until life time. The evaluation results are as follows; Fast neutron fluences for capsules U, V, X and W are 4.983E+18, 1.641E+19, 3.158E+19, and 4.469E+19n/cm{sup 2}, respectively. The bias factor, the ratio of calculation/measurement, was 0.840 for the 1st through 4th testing and the calculational uncertainty, 12% satisfied the requirement of USNRC Reg.Guide DG-1053, 20%. The best estimated neutron fluence for reactor vessel inside surface was 1.362E+19n/cm{sup 2} based on the end of 12th fuel cycle and it was predicted that the fluences of vessel inside surface at 32, 40, 48 and 56EFPY would reach 3.481E+19, 4.209E+19, 5.144E+19 and 5.974E+19n/cm{sup 2} based on the current calculation. The result through this analysis for Kori unit 3 showed that there would be no problem for the pressurized thermal shock(PTS) during the operation until design life. 48 refs., 35 figs., 41 tabs. (Author)

  7. Closure Report for Corrective Action Unit 261: Area 25 Test Cell A Leachfield System, Nevada Test Site, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    T. M. Fitzmaurice

    2001-04-01

    The purpose of this Closure Report (CR) is to provide documentation of the completed corrective action at the Test Cell A Leachfield System and to provide data confirming the corrective action. The Test Cell A Leachfield System is identified in the Federal Facility Agreement and Consent Order (FFACO) of 1996 as Corrective Action Unit (CAU) 261. Remediation of CAU 261 is required under the FFACO (1996). CAU 261 is located in Area 25 of the Nevada Test Site (NTS) which is approximately 140 kilometers (87 miles) northwest of Las Vegas, Nevada (Figure 1). CAU 261 consists of two Corrective Action Sites (CASS): CAS 25-05-01, Leachfield; and CAS 25-05-07, Acid Waste Leach Pit (AWLP) (Figures 2 and 3). Test Cell A was operated during the 1960s and 1970s to support the Nuclear Rocket Development Station. Various operations within Building 3124 at Test Cell A resulted in liquid waste releases to the Leachfield and the AWLP. The following existing site conditions were reported in the Corrective Action Decision Document (CADD) (U.S. Department of Energy, Nevada Operations Office [DOE/NV], 1999): Soil in the leachfield was found to exceed the Nevada Division of Environmental Protection (NDEP) Action Level for petroleum hydrocarbons, the U.S. Environmental Protection Agency (EPA) preliminary remediation goals for semi volatile organic compounds, and background concentrations for strontium-90; Soil below the sewer pipe and approximately 4.5 meters (m) (15 feet [ft]) downstream of the initial outfall was found to exceed background concentrations for cesium-137 and strontium-90; Sludge in the leachfield septic tank was found to exceed the NDEP Action Level for petroleum hydrocarbons and to contain americium-241, cesium-137, uranium-234, uranium-238, potassium-40, and strontium-90; No constituents of concern (COC) were identified at the AWLP. The NDEP-approved CADD (DOWNV, 1999) recommended Corrective Action Alternative 2, ''Closure of the Septic Tank and Distribution Box

  8. Design of the Wendelstein 7-X inertially cooled Test Divertor Unit Scraper Element

    Energy Technology Data Exchange (ETDEWEB)

    Lumsdaine, Arnold, E-mail: lumsdainea@ornl.gov [Oak Ridge National Laboratory, Oak Ridge, TN (United States); Boscary, Jean [Max Planck Institute for Plasma Physics, Garching (Germany); Fellinger, Joris [Max Planck Institute for Plasma Physics, Greifswald (Germany); Harris, Jeff [Oak Ridge National Laboratory, Oak Ridge, TN (United States); Hölbe, Hauke; König, Ralf [Max Planck Institute for Plasma Physics, Greifswald (Germany); Lore, Jeremy; McGinnis, Dean [Oak Ridge National Laboratory, Oak Ridge, TN (United States); Neilson, Hutch; Titus, Peter [Princeton Plasma Physics Lab, Princeton, NJ (United States); Tretter, Jörg [Max Planck Institute for Plasma Physics, Garching (Germany)

    2015-10-15

    Highlights: • The justification for the installation of the Test Divertor Unit Scraper Element is given. • Specially designed operational scenarios for the component are presented. • Plans for the design of the component are detailed. - Abstract: The Wendelstein 7-X stellarator is scheduled to begin operation in 2015, and to achieve full power steady-state operation in 2019. Computational simulations have indicated that for certain plasma configurations in the steady-state operation, the ends of the divertor targets may receive heat fluxes beyond their qualified technological limit. To address this issue, a high heat-flux “scraper element” (HHF-SE) has been designed that can protect the sensitive divertor target region. The surface profile of the HHF-SE has been carefully designed to meet challenging engineering requirements and severe spatial limitations through an iterative process involving physics simulations, engineering analysis, and computer aided design rendering. The desire to examine how the scraper element interacts with the plasma, both in terms of how it protects the divertor, and how it affects the neutral pumping efficiency, has led to the consideration of installing an inertially cooled version during the short pulse operation phase. This Test Divertor Unit Scraper Element (TDU-SE) would replicate the surface profile of the HHF-SE. The design and instrumentation of this component must be completed carefully in order to satisfy the requirements of the machine operation, as well as to support the possible installation of the HHF-SE for steady-state operation.

  9. Leak rate and burst test data for McGuire Unit 1 steam generator tubes

    Energy Technology Data Exchange (ETDEWEB)

    Sherburne, P.A. [B& W Nuclear Service Co., Lynchburg, VA (United States); Frye, C.R. [Babcock & Wilcox Co., Lynchburg, VA (United States); Mayes, D.B. [Duke Power Co., Charlotte, NC (United States)

    1992-12-31

    To support the development of tube plugging criteria that would allow tubes with through-wall cracks to remain in service, sections of 12 tubes were removed from the McGuire Unit-1 steam generators. These tubes were sent to B&W Nuclear Service Company for metallographic examination and for determination of burst pressure and leak rate at both operating and faulted conditions. Primary water stress corrosion cracking (PWSCC) had degraded these tubes in the tube-to-tubesheet roll transitions. To measure primary-to-secondary leakage at pressures and temperatures equivalent to those in the McGuire Unit-1 steam generators, an autoclave-based test loop was designed and installed at the Babcock & Wilcox Lynchburg Research Center. Sections of the tube containing the roll transitions were then installed in the autoclave and actual primary- to-secondary leakage was measured at 288{degrees}C (550{degrees}F) and at 9 and 18.3 MPa (1300 and 2650 psi) pressure differentials. Following the leak test, the tubes were pressurized internally until the tube wall ruptured. Leak rate, burst pressure, and eddy-current information were then correlated with the through-wall crack lengths as determined by metallographic examination. Results confirm the ability to measure the crack length with eddy-current techniques. Results also support analytical and empirical models developed by the nuclear industry in calculating critical crack lengths in roll transitions.

  10. Closure Report for Corrective Action Unit 540: Spill Sites, Nevada Test Site, Nevada, Rev. No.: 0

    Energy Technology Data Exchange (ETDEWEB)

    McClure, Lloyd

    2006-10-01

    This Closure Report (CR) presents information supporting the closure of Corrective Action Unit (CAU) 540: Spill Sites, Nevada Test Site, Nevada. This CR complies with the requirements of the 'Federal Facility Agreement and Consent Order' (1996) that was agreed to by the State of Nevada, the U.S. Department of Energy, and the U.S. Department of Defense. Corrective Action Unit 540 is located within Areas 12 and 19 of the Nevada Test Site and is comprised of the following Corrective Action Sites (CASs): CAS 12-44-01, ER 12-1 Well Site Release; CAS 12-99-01, Oil Stained Dirt; CAS 19-25-02, Oil Spill; CAS 19-25-04, Oil Spill; CAS 19-25-05, Oil Spill; CAS 19-25-06, Oil Spill; CAS 19-25-07, Oil Spill; CAS 19-25-08, Oil Spills (3); and CAS 19-44-03, U-19bf Drill Site Release. The purpose of this CR is to provide documentation supporting recommendations of no further action for the CASs within CAU 540. To achieve this, the following actions were performed: (1) Reviewed the current site conditions, including the concentration and extent of contamination; (2) Performed closure activities to address the presence of substances regulated by 'Nevada Administrative Code' 445A.2272 (NAC, 2002); and (3) Documented Notice of Completion and closure of CAU 540 issued by the Nevada Division of Environmental Protection.

  11. Closure Report for Corrective Action Unit 143: Area 25 Contaminated Waste Dumps, Nevada Test Site, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    D. S. Tobiason

    2002-03-01

    This Closure Report (CR) has been prepared for the Area 25 Contaminated Waste Dumps (CWD), Corrective Action Unit (CAU) 143 in accordance with the Federal Facility Agreement and Consent Order [FFACO] (FFACO, 1996) and the Nevada Division of Environmental Protection (NDEP)-approved Corrective Action Plan (CAP) for CAU 143: Area 25, Contaminated Waste Dumps, Nevada Test Site, Nevada. CAU 143 consists of two Corrective Action Sites (CASs): 25-23-09 CWD No.1, and 25-23-03 CWD No.2. The Area 25 CWDs are historic disposal units within the Area 25 Reactor Maintenance, Assembly, and Disassembly (R-MAD), and Engine Maintenance, Assembly, and Disassembly (E-MAD) compounds located on the Nevada Test Site (NTS). The R-MAD and E-MAD facilities originally supported a portion of the Nuclear Rocket Development Station in Area 25 of the NTS. CWD No.1 CAS 25-23-09 received solid radioactive waste from the R-MAD Compound (East Trestle and West Trench Berms) and 25-23-03 CWD No.2 received solid radioactive waste from the E-MAD Compound (E-MAD Trench).

  12. RCGVS design improvement and depressurization capability tests for Ulchin nuclear power plant units 3 and 4

    Energy Technology Data Exchange (ETDEWEB)

    Sung, Kang Sik; Seong, Ho Je; Jeong, Won Sang; Seo, Jong Tae; Lee, Sang Keun [Korea Power Engineering Company, Inc., Seoul (Korea, Republic of); Lim, Keun Hyo; Choi, Kwon Sik; Oh, Chul Sung [Korea Electric Power Cooperation, Taejon (Korea, Republic of)

    1998-12-31

    The Reactor Coolant Gas Vent System(RCGVS) design for Ulchin Nuclear Power Plant Units 3 and 4 (UCN 3 and 4) has been improved from the Yonggwang Nuclear Power Plant Units 3 and 4 (YGN 3 and 4) based on the evaluation results for depressurization capability tests performed at YGN 3 and 4. There has been a series of plant safety analyses for Natural Circulation Cooldown(NCC) event and thermo-dynamic analyses with RELAP5 code for the steam blowdown phenomena in order to optimize the orifice size of UCN 3 and 4 RCGVS. Based on these analyses results, the RCGVS orifics size for UCN 3 and 4 has been reduced to 9/32 inch from the 11/32 inch for YGN 3 and 4. The depressurization capability tests, which were performed at UCN 3 in order to verify the FSAR NCC analysis results, show that the RCGVS depressurization rates are being within the acceptable ranges. Therefore, it is concluded that the orificed flow path of UCN 3 and 4 RCGVS is adequately designed, and can provide the safety-grade depressurization capability required for a safe plant operation. 6 refs., 5 figs., 1 tab. (Author)

  13. Developing and testing a tool to measure nurse/physician communication in the intensive care unit.

    Science.gov (United States)

    Manojlovich, Milisa; Saint, Sanjay; Forman, Jane; Fletcher, Carol E; Keith, Rosalind; Krein, Sarah

    2011-06-01

    The purpose of this study, conducted in 3 intensive care units (ICUs) at 1 Department of Veterans Affairs Medical Center, was to develop tools and procedures to measure nurse/physician communication in future studies. We used mixed methods in a multistaged approach. Qualitative data came from 4 observations of patient care rounds and 8 interviews with nurses and physicians. Quantitative data came from anonymous surveys distributed to nurses in all 3 ICUs (n = 66). We administered the Safety Organizing Scale to measure nurses' self-reported behaviors that enable a safety culture. Analysis of variance was the main statistical test. Qualitative data were used to create an observation data collection tool and a working protocol, to measure nurse/physician communication in a future study. Analysis of variance revealed significant differences between the 3 units (f = 4.57, P = 0.02). There also were significant differences on 4 of 9 items of the Safety Organizing Scale. Using mixed methods, we gained multiple perspectives that helped us to clarify and validate the context and content of communication. Quantitative analysis showed significant differences between the 3 ICUs in nurses' perceptions of a safety culture. According to qualitative analyses, nurses from the unit which reported the weakest safety culture also were the least satisfied in their communication with physicians. Qualitative analyses corroborated quantitative findings and demonstrated the importance of contextual influences on nurse/physician communication. Through the tools and protocol we created, more realistic strategies to promote effective communication between nurses and physicians may be developed and tested in future studies.

  14. The Paleobiosphere: a novel device for the in vivo testing of hydrocarbon producing-utilizing microorganisms.

    Science.gov (United States)

    Strobel, Gary; Booth, Eric; Schaible, George; Mends, Morgan Tess; Sears, Joe; Geary, Brad

    2013-04-01

    The construction and testing of a unique instrument, the Paleobiosphere, which mimics some of the conditions of the ancient earth, is described. The instrument provides an experimental testing system for determining if certain microbes, when provided an adequate environment, can degrade biological materials to produce fuel-like hydrocarbons in a relatively short time frame that become trapped by the shale. The conditions selected for testing included a particulate Montana shale (serving as the "Trap Shale"), plant materials (leaves and stems of three extant species whose origins are in the late Cretaceous), a water-circulating system, sterile air, and a specially designed Carbotrap through which all air was passed as exhaust and volatile were hydrocarbons trapped. The fungus for initial testing was Annulohypoxylon sp., isolated as an endophyte of Citrus aurantifolia. It produces, in solid and liquid media, a series of hydrocarbon-like molecules. Some of these including 1,8-cineole, 2-butanone, propanoic acid, 2-methyl-, methyl ester, benzene (1-methylethyl)-, phenylethyl alcohol, benzophenone and azulene, 1,2,3,5,6,7,8,8a-octahydro-1,4-dimethyl-7-(1-methylethenyl), [1S-(1α,7α,8aβ)]. These were the key signature compounds used in an initial Paleobiosphere test. After 3 weeks, incubation, the volatiles associated with the harvested "Trap Shale" included each of the signature substances as well as other fungal-associated products: some indanes, benzene derivatives, some cyclohexanes, 3-octanone, naphthalenes and others. The fungus thus produced a series of "Trap Shale" products that were representative of each of the major classes of hydrocarbons in diesel fuel (Mycodiesel). Initial tests with the Paleobiosphere offer some evidence for a possible origin of hydrocarbons trapped in bentonite shale. Thus, with modifications, numerous other tests can also be designed for utilization in the Paleobiosphere.

  15. Evaluation of an onsite alcohol testing device for use in postmortem forensic toxicology.

    Science.gov (United States)

    Engelhart, D A; Jenkins, A J

    2001-10-01

    The disposable QED saliva alcohol test provides a very simple, fast, and reliable means for quantitative onsite alcohol detection. The purpose of this study was to determine if the QED test would be a useful tool for the determination of postmortem ethanol levels in cases where a rapid result was needed. QED results were compared with ethanol levels determined by headspace GC analysis. Both saliva and vitreous humor specimens were used for the evaluation. QED tests were initially attempted using the oral fluid from 50 individuals. Of these cases, 17 of the tests were valid with 8 positive results. For 23 cases the oral fluid was not attainable, and for 10 cases, the sample was contaminated with blood making the tests invalid. The correlation between the oral fluid results and the blood headspace GC analysis was poor (r = 0.8345) over the range of 0.01-0.29 g/dL. Vitreous specimens were found to be the matrix of choice for analyzing postmortem cases using the QED. Only 6 of 171 specimens were found to be unsuitable. The QED results correlated well with the headspace GC analysis (r = 0.9931, n = 165). When using ethanol levels > 0.02 g/dL (n = 126), an average vitreous (GC)/blood ratio of 1.16 correlated well with the average QED/blood ratio of 1.22. Although the QED saliva alcohol test does not appear to be useful in determining postmortem saliva ethanol levels, it does provide accurate results when using postmortem vitreous humor as the testing matrix.

  16. Nonlinear behaviour of the Chinese SSEC index with a unit root: Evidence from threshold unit root tests

    Science.gov (United States)

    Qian, Xi-Yuan; Song, Fu-Tie; Zhou, Wei-Xing

    2008-01-01

    We have investigated the behaviour of the Shanghai Stock Exchange Composite (SSEC) index for the period from 1990:12 to 2007:06 using an unconstrained two-regime threshold autoregressive (TAR) model with a unit root developed by Caner and Hansen. The method allows us to simultaneously consider nonstationarity and nonlinearity in time series that has regime switching. Our finding indicates that the Shanghai stock market exhibits nonlinear behaviour with two regimes and has unit roots in both regimes. The important implications of the threshold effect in stock markets are also discussed.

  17. A UVC Device for Intra-luminal Disinfection of Catheters: In Vitro Tests on Soft Polymer Tubes Contaminated with Pseudomonas aeruginosa, Staphylococcus aureus, Escherichia coli and Candida albicans

    DEFF Research Database (Denmark)

    Bak, Jimmy; Begovic, Tanja; Bjarnsholt, Thomas

    2011-01-01

    light is possible. In this paper we present dose-response results using a newly developed UVC disinfection device, which can be connected to a Luer catheter hub. The device was tested on soft polymer tubes contaminated with a pallet of microorganisms, including Candida albicans, Staphylococcus aureus...

  18. The Near Mallett Unit Foveal Suppression Test: a cross-sectional study to establish test norms and relationship with other optometric tests.

    Science.gov (United States)

    Tang, Sosena T W; Evans, Bruce J W

    2007-01-01

    When the binocular system comes under prolonged stress in decompensated heterophoria, a small suppression area can develop at the fovea. This foveal suppression (FS) may be an adaptation to eliminate symptoms. The near Mallett unit (NMU) is a hand-held instrument that contains a binocular status test for detecting and quantifying FS. We measured FS in a cross-sectional study of 131 patients to investigate the normal range of responses. A ratio scoring method was devised which considers the number of letters read with dichoptic viewing when binocularly fused (b) and under monocular (m) conditions, using the formula 100 x (m - b)/m. The 95th percentile value of the FS ratios was calculated as the limit of the normal range and this gave a value for the right eye (RE; 33%), left eye (LE; 43%) and total (38%). This result shows that statistically significant FS occurs when a patient can read approximately one line further in the test monocularly, compared to under fused dichoptic conditions. A statistically significant correlation was found between absolute values of horizontal aligning prism (associated heterophoria on the NMU) and FS ratio. Some limitations of the FS test and unexpected results became apparent during our research and an abnormal result on the test does not always indicate a binocular vision anomaly. Nonetheless, we feel that the test can provide useful information when the results are taken in the context of other clinical tests. Our results are used to develop recommendations and clinical guidelines for using the FS test, and to make suggestions for improvements in future designs of the test.

  19. 1994 Baseline biological studies for the Device Assembly Facility at the Nevada Test Site

    Energy Technology Data Exchange (ETDEWEB)

    Townsend, Y.E. [ed.; Woodward, B.D.; Hunter, R.B.; Greger, P.D.; Saethre, M.B.

    1995-02-01

    This report describes environmental work performed at the Device Assembly Facility (DAF) in 1994 by the Basic Environmental Monitoring and Compliance Program (BECAMP). The DAF is located near the Mojave-Great Basin desert transition zone 27 km north of Mercury. The area immediately around the DAF building complex is a gentle slope cut by 1 to 3 m deep arroyos, and occupied by transitional vegetation. In 1994, construction activities were largely limited to work inside the perimeter fence. The DAF was still in a preoperational mode in 1994, and no nuclear materials were present. The DAF facilities were being occupied so there was water in the sewage settling pond, and the roads and lights were in use. Sampling activities in 1994 represent the first year in the proposed monitoring scheme. The proposed biological monitoring plan gives detailed experimental protocols. Plant, lizard, tortoise, small mammal, and bird surveys were performed in 1994. The authors briefly outline procedures employed in 1994. Studies performed on each taxon are reviewed separately then summarized in a concluding section.

  20. Usability Testing of a Collaborative and Interactive University on a Mobile Device

    Directory of Open Access Journals (Sweden)

    Gavin McArdle

    2009-10-01

    Full Text Available Abstract - The use of mobile devices for delivering learning tools is an attractive concept. Termed mobile learning (m-learning, this new technology allows people to participate in learning activities without being tied to a fixed location and provides users with convenient and flexible access to learning resources anytime and anywhere. While many m-learning applications have been developed to date, most provide tools to help students’ with specific learning tasks rather than a general interface to online courses. Few sup-port online learning communities or allow users to download multimedia learning content. These features would engage mobile users and enable them to interact with one another, thus allowing them to participate in group learning activities despite their changing location. In this article, we describe an m-learning system which we have developed which aims to incorporate these facilities. This system provides access to multimedia learning resources and supports mobile users in an interactive synchronous learning environment with their desktop peers. Details of the evaluation techniques which we utilised to appraise the system are provided and the results are presented. Feedback suggests that the features offered by our system are beneficial for collaborative m-learning.