Modeling, Testing, and Characteristic Analysis of a Planetary Flywheel Inerter

Directory of Open Access Journals (Sweden)

Zheng Ge

2018-01-01

Full Text Available We propose the planetary flywheel inerter, which is a new type of ball screw inerter. A planetary flywheel consists of several planetary gears mounted on a flywheel bracket. When the flywheel bracket is driven by a screw and rotating, each planetary gear meshing with an outer ring gear generates a compound motion composed of revolution and rotation. Theoretical analysis shows that the output force of the planetary flywheel inerter is proportional to the relative acceleration of one terminal of the inerter to the other. Optimizing the gear ratio of the planetary gears to the ring gear allows the planetary flywheel to be lighter than its traditional counterpart, without any loss on the inertance. According to the structure of the planetary flywheel inerter, nonlinear factors of the inerter are analyzed, and a nonlinear dynamical model of the inerter is established. Then the parameters in the model are identified and the accuracy of the model is validated by experiment. Theoretical analysis and experimental data show that the dynamical characteristics of a planetary flywheel inerter and those of a traditional flywheel inerter are basically the same. It is concluded that a planetary flywheel can completely replace a traditional flywheel, making the inerter lighter.

Fog inerting criteria for hydrogen/air mixtures

International Nuclear Information System (INIS)

Tsai, S.S.; Liparulo, N.J.

1982-01-01

A distributed ignition system has been proposed to ignite hydrogen at low concentration in the ice condenser containment during severe accidents. The post-accident containment atmosphere could be misty due to fog generation from the break flow and condensation in the ice bed. Thus it is important to establish a fog inerting criterion for effective performance of the ignition system. This paper presents such a criterion that specifies the necessary fogging conditions, i.e., fog concentration and drop size, for inerting a hydrogen/air mixture. The criterion shows that the minimum fog inerting concentration varies with the square of the volume mean fog drop size. The present fog inerting criterion is shown to be in general agreement with the Factory Mutual test data

7 CFR 201.51 - Inert matter.

Science.gov (United States)

2010-01-01

... REGULATIONS Purity Analysis in the Administration of the Act § 201.51 Inert matter. Inert matter shall include... kochia that pass through a 1 mm opening, square-hole sieve, when shaken for 30 seconds. (8) The thin... devoid of the husk and pass through a 1/13th-inch, round-hole sieve. (ii) Bulblets which show evident...

On the Benefits of Semi-Active Suspensions with Inerters

Directory of Open Access Journals (Sweden)

Xin-Jie Zhang

2012-01-01

Full Text Available Inerters have become a hot topic in recent years especially in vehicle, train, building suspension systems, etc. Eight different layouts of suspensions were analyzed with a quarter-car model in this paper. Dimensionless root mean square (RMS responses of the sprung mass vertical acceleration, the suspension travel, and the tire deflection are derived which were used to evaluate the performance of the quarter-car model. The behaviour of semi-active suspensions with inerters using Groundhook, Skyhook, and Hybrid control has been evaluated and compared to the performance of passive suspensions with inerters. Sensitivity analysis was applied to the development of a high performance semi-active suspension with an inerter. Numerical simulations indicate that a semi-active suspension with an inerter has much better performance than the passive suspension with an inerter, especially with the Hybrid control method, which has the best compromise between comfort and road holding quality.

Alternative inerting agents

CSIR Research Space (South Africa)

Du

1997-08-01

Full Text Available Final Project Report ALTERNATIVE INERTING AGENTS Author/s: J J L DU PLESSIS Research Agency: OSIR MINING TECHNOLOGY Project No: Date: 3 2 7 2 COL 443 APRIL 1999 N’ ) ( G~6~ I Title: 9 / The results show...

Development of new polysilsesquioxane spherical particles as stabilized active ingredients for sunscreens

Science.gov (United States)

Tolbert, Stephanie Helene

Healthy skin is a sign of positive self-worth, attractiveness and vitality. Compromises to this are frequently caused by extended periods of recreation in the sun and in turn exposure to the harmful effects of UV radiation. To maintain strength and integrity, protection of the skin is paramount. This can be achieved by implementing skin-care products which contain sunscreen active ingredients that provide UV protection. Unfortunately, photo-degradation, toxicity, and photo-allergies limit the effectiveness of present day sunscreen ingredients. Currently, this is moderated by physically embedding within inert silica particles, but leaching of the active ingredient can occur, thereby negating protective efforts. Alternatively, this research details the preparation and investigation of bridged silsesquioxane analogues of commercial ingredients which can be chemically grafted to the silica matrix. Studies with bridged salicylate particles detail facile preparation, minimized leaching, and enhanced UV stability over physically encapsulated and pendant salicylate counterparts. In terms of UVB protective ability, the highest maintenance of sun protection factor (SPF) after extended UV exposure was achieved with bridged incorporation, and has been attributed to corollary UV stability. Additionally, bridged salicylate particles can be classified as broad-spectrum, and rate from moderate to good in terms of UVA protective ability. Particles incorporated with a bridged curcuminoid silsesquioxane were also prepared and displayed comparable results. As such, an attractive method for sunscreen isolation and stabilization has been developed to eliminate the problems associated with current sunscreens, all while maintaining the established UV absorbance profiles of the parent compound. To appreciate the technology utilized in this research, a thorough understanding of sol-gel science as it pertains to hybrid organic/silica particles, including methods of organic fragment

Catalytic Reactor for Inerting of Aircraft Fuel Tanks

Science.gov (United States)

1974-06-01

Aluminum Panels After Triphase Corrosion Test 79 35 Inerting System Flows in Various Flight Modes 82 36 High Flow Reactor Parametric Data 84 37 System...AD/A-000 939 CATALYTIC REACTOR FOR INERTING OF AIRCRAFT FUEL TANKS George H. McDonald, et al AiResearch Manufacturing Company Prepared for: Air Force...190th Street 2b. GROUP Torrance, California .. REPORT TITLE CATALYTIC REACTOR FOR INERTING OF AIRCRAFT FUEL TANKS . OESCRIP TIVE NOTEs (Thpe of refpoft

Unidentified Flying Objects (UFOs). LC Science Tracer Bullet.

Science.gov (United States)

Library of Congress, Washington, DC. Science and Technology Div.

This guide lists information sources dealing with unidentified flying objects (UFOs). Not meant to be a comprehensive bibliography, this compilation is designed--as the name of the series implies--to put the reader "on target." Included are: (1) subject headings used by the Library of Congress, under which publications on this subject…

A new understanding of inert gas narcosis

International Nuclear Information System (INIS)

Zhang Meng; Gao Yi; Fang Haiping

2016-01-01

Anesthetics are extremely important in modern surgery to greatly reduce the patient’s pain. The understanding of anesthesia at molecular level is the preliminary step for the application of anesthetics in clinic safely and effectively. Inert gases, with low chemical activity, have been found to cause anesthesia for centuries, but the mechanism is unclear yet. In this review, we first summarize the progress of theories about general anesthesia, especially for inert gas narcosis, and then propose a new hypothesis that the aggregated rather than the dispersed inert gas molecules are the key to trigger the narcosis to explain the steep dose-response relationship of anesthesia. (topical review)

Constraints on Galactic populations from the unidentified EGRET sources

International Nuclear Information System (INIS)

Siegal-Gaskins, Jennifer M.; Pavlidou, Vasiliki; Brown, Carolyn; Olinto, Angela V.; Fields, Brian D.

2007-01-01

A significant fraction of the sources in the third EGRET catalog have not yet been identified with a low-energy counterpart. We evaluate the plausibility of a Galactic population accounting for some or all of the unidentified EGRET sources by making the simple assumption that galaxies similar to the Milky Way host comparable populations of gamma-ray emitters. Rather than focusing on the properties of a specific candidate emitter, we constrain the abundance and spatial distribution of proposed Galactic populations. We find that it is highly improbable that the unidentified EGRET sources contain more than a handful of members of a Galactic halo population, but that current observations are consistent with all of these sources being Galactic objects if they reside entirely in the disk and bulge. We discuss the additional constraints and new insights into the nature of Galactic gamma-ray emitting populations that GLAST is expected to provide

Online learning dynamics of multilayer perceptrons with unidentifiable parameters

Energy Technology Data Exchange (ETDEWEB)

Park, Hyeyoung [Laboratory for Mathematical Neuroscience, RIKEN Brain Science Institute, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); Inoue, Masato [Laboratory for Mathematical Neuroscience, RIKEN Brain Science Institute, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); Department of Otolaryngology, Head and Neck Surgery, Graduate School of Medicine, Kyoto University, Kyoto 606-8507 (Japan); ' Intelligent Cooperation and Control' , PRESTO, JST, c/o RIKEN BSI, Saitama 351-0198 (Japan); Okada, Masato [Laboratory for Mathematical Neuroscience, RIKEN Brain Science Institute, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan)

2003-11-28

In the over-realizable learning scenario of multilayer perceptrons, in which the student network has a larger number of hidden units than the true or optimal network, some of the weight parameters are unidentifiable. In this case, the teacher network consists of a union of optimal subspaces included in the parameter space. The optimal subspaces, which lead to singularities, are known to affect the estimation performance of neural networks. Using statistical mechanics, we investigate the online learning dynamics of two-layer neural networks in the over-realizable scenario with unidentifiable parameters. We show that the convergence speed strongly depends on the initial parameter conditions. We also show that there is a quasi-plateau around the optimal subspace, which differs from the well-known plateaus caused by permutation symmetry. In addition, we discuss the property of the final learning state, relating this to the singular structures.

Online learning dynamics of multilayer perceptrons with unidentifiable parameters

International Nuclear Information System (INIS)

Park, Hyeyoung; Inoue, Masato; Okada, Masato

2003-01-01

In the over-realizable learning scenario of multilayer perceptrons, in which the student network has a larger number of hidden units than the true or optimal network, some of the weight parameters are unidentifiable. In this case, the teacher network consists of a union of optimal subspaces included in the parameter space. The optimal subspaces, which lead to singularities, are known to affect the estimation performance of neural networks. Using statistical mechanics, we investigate the online learning dynamics of two-layer neural networks in the over-realizable scenario with unidentifiable parameters. We show that the convergence speed strongly depends on the initial parameter conditions. We also show that there is a quasi-plateau around the optimal subspace, which differs from the well-known plateaus caused by permutation symmetry. In addition, we discuss the property of the final learning state, relating this to the singular structures

Model identification methodology for fluid-based inerters

Science.gov (United States)

Liu, Xiaofu; Jiang, Jason Zheng; Titurus, Branislav; Harrison, Andrew

2018-06-01

Inerter is the mechanical dual of the capacitor via the force-current analogy. It has the property that the force across the terminals is proportional to their relative acceleration. Compared with flywheel-based inerters, fluid-based forms have advantages of improved durability, inherent damping and simplicity of design. In order to improve the understanding of the physical behaviour of this fluid-based device, especially caused by the hydraulic resistance and inertial effects in the external tube, this work proposes a comprehensive model identification methodology. Firstly, a modelling procedure is established, which allows the topological arrangement of the mechanical networks to be obtained by mapping the damping, inertance and stiffness effects directly to their respective hydraulic counterparts. Secondly, an experimental sequence is followed, which separates the identification of friction, stiffness and various damping effects. Furthermore, an experimental set-up is introduced, where two pressure gauges are used to accurately measure the pressure drop across the external tube. The theoretical models with improved confidence are obtained using the proposed methodology for a helical-tube fluid inerter prototype. The sources of remaining discrepancies are further analysed.

Inert Anode Report

Energy Technology Data Exchange (ETDEWEB)

none,

1999-07-01

This ASME report provides a broad assessment of open literature and patents that exist in the area of inert anodes and their related cathode systems and cell designs, technologies that are relevant for the advanced smelting of aluminum. The report also discusses the opportunities, barriers, and issues associated with these technologies from a technical, environmental, and economic viewpoint.

Identification of the geographical place of origin of an unidentified individual by multi-isotope analysis

NARCIS (Netherlands)

Font Morales, L.; van der Peijl, G.J.Q.; van Leeuwen, C.; van Wetten, I.A.; Davies, G.R.

2015-01-01

A multi-isotope investigation (Sr and Pb isotopes and δ18O, δ13C and δ15N) was applied to bone and teeth from an unidentified male found drowned in the"IJ" Ruyterkade in Amsterdam, The Netherlands in March of 1999. The individual remained unidentified until mid 2013, after the isotope study was

46 CFR 154.908 - Inert gas generator: Location.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Inert gas generator: Location. 154.908 Section 154.908 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY... Atmospheric Control in Cargo Containment Systems § 154.908 Inert gas generator: Location. (a) Except as...

Experimental Study of an On-board Fuel Tank Inerting System

Science.gov (United States)

Wu, Fei; Lin, Guiping; Zeng, Yu; Pan, Rui; Sun, Haoyang

2017-03-01

A simulated aircraft fuel tank inerting system was established and experiments were conducted to investigate the performance of the system. The system uses hollow fiber membrane which is widely used in aircraft as the air separation device and a simplified 20% scale multi compartment fuel tank as the inerting object. Experiments were carried out to investigate the influences of different operating parameters on the inerting effectiveness of the system, including NEA (nitrogen-enriched air) flow rate, NEA oxygen concentration, NEA distribution, pressure of bleeding air and fuel load of the tank. Results showed that for the multi compartment fuel tank, concentrated flow washing inerting would cause great differences throughout the distribution of oxygen concentration in the fuel tank, and inerting dead zone would exist. The inerting effectiveness was greatly improved and the ullage oxygen concentration of the tank would reduce to 12% successfully when NEA entered three compartments evenly. The time span of a complete inerting process reduced obviously with increasing NEA flow rate and decreasing NEA concentration, but the trend became weaker gradually. However, the reduction of NEA concentration will decrease the utilization efficiency of the bleeding air. In addition, the time span can also be reduced by raising the pressure of bleeding air, which will improve the bleeding air utilization efficiency at the same time. The time span decreases linearly as the fuel load increases.

What determines ingredient awareness of consumers? A study on ten functional food ingredients

NARCIS (Netherlands)

Bornkessel, S.; Bröring, S.; Omta, S.W.F.; Trijp, van J.C.M.

2014-01-01

Given the importance of consumer awareness of functional food ingredients for healthy food choices, the aim of this study is to explore consumers’ ingredient awareness and the determinants which influence the awareness about functional food ingredients. A sample of 200 German consumers was

One-loop contributions to neutral minima in the inert doublet model

Energy Technology Data Exchange (ETDEWEB)

Ferreira, P.M. [Instituto Superior de Engenharia de Lisboa - ISEL,1959-007 Lisboa (Portugal); Centro de Física Teórica e Computacional - FCUL,Universidade de Lisboa, R. Ernesto de Vasconcelos, 1749-016 Lisboa (Portugal); Świeżewska, Bogumiła [Faculty of Physics, University of Warsaw,Pasteura 5, 02-093 Warsaw (Poland)

2016-04-15

The vacuum structure of the inert doublet model is analysed at the one-loop level using the effective potential formalism, to verify the validity of tree-level predictions for the properties of the global minimum. An inert minimum (with massive fermions) and an inert-like minimum (with massless fermions) can coexist at tree level. But the one-loop analysis reveals that the allowed parameter space for the coexistence of more than one minimum is larger than the tree-level expected one. It is also shown that for some choices of parameters, the global minimum found at the one-loop level may be inert (or inert-like), contrary to what the tree-level analysis indicates.

Nuclear Technology. Course 28: Welding Inspection. Module 28-3, Tungsten Inert Gas (TIG), Metal Inert Gas (MIG) and Submerged Arc Welding.

Science.gov (United States)

Espy, John

This third in a series of ten modules for a course titled Welding Inspection presents the apparatus, process techniques, procedures, applications, associated defects, and inspection for the tungsten inert gas, metal inert gas, and submerged arc welding processes. The module follows a typical format that includes the following sections: (1)…

Portable spectrometer monitors inert gas shield in welding process

Science.gov (United States)

Grove, E. L.

1967-01-01

Portable spectrometer using photosensitive readouts, monitors the amount of oxygen and hydrogen in the inert gas shield of a tungsten-inert gas welding process. A fiber optic bundle transmits the light from the welding arc to the spectrometer.

Neutralino dark matter with inert higgsinos and singlinos

International Nuclear Information System (INIS)

Hall, Jonathan P.; King, Stephen F.

2009-01-01

We discuss neutralino dark matter arising from supersymmetric models with extra inert Higgsinos and singlinos, where inert means that their scalar partners do not get vacuum expectation values. As an example, we consider the extended neutralino sector of the E 6 SSM, which predicts three families of Higgs doublet pairs, plus three singlets, plus a Z', together with their fermionic superpartners. We show that the two families of inert doublet Higgsinos and singlinos predicted by this model provide an almost decoupled neutralino sector with a naturally light LSP which can account for the cold dark matter relic abundance independently of the rest of the model, providing that the ratio of the two usual Higgs doublets satisfies tan β < 2.

Mining metadata from unidentified ITS sequences in GenBank: A case study in Inocybe (Basidiomycota

Directory of Open Access Journals (Sweden)

Jacobsson Stig

2008-02-01

Full Text Available Abstract Background The lack of reference sequences from well-identified mycorrhizal fungi often poses a challenge to the inference of taxonomic affiliation of sequences from environmental samples, and many environmental sequences are thus left unidentified. Such unidentified sequences belonging to the widely distributed ectomycorrhizal fungal genus Inocybe (Basidiomycota were retrieved from GenBank and divided into species that were identified in a phylogenetic context using a reference dataset from an ongoing study of the genus. The sequence metadata of the unidentified Inocybe sequences stored in GenBank, as well as data from the corresponding original papers, were compiled and used to explore the ecology and distribution of the genus. In addition, the relative occurrence of Inocybe was contrasted to that of other mycorrhizal genera. Results Most species of Inocybe were found to have less than 3% intraspecific variability in the ITS2 region of the nuclear ribosomal DNA. This cut-off value was used jointly with phylogenetic analysis to delimit and identify unidentified Inocybe sequences to species level. A total of 177 unidentified Inocybe ITS sequences corresponding to 98 species were recovered, 32% of which were successfully identified to species level in this study. These sequences account for an unexpectedly large proportion of the publicly available unidentified fungal ITS sequences when compared with other mycorrhizal genera. Eight Inocybe species were reported from multiple hosts and some even from hosts forming arbutoid or orchid mycorrhizae. Furthermore, Inocybe sequences have been reported from four continents and in climate zones ranging from cold temperate to equatorial climate. Out of the 19 species found in more than one study, six were found in both Europe and North America and one was found in both Europe and Japan, indicating that at least many north temperate species have a wide distribution. Conclusion Although DNA

Mining metadata from unidentified ITS sequences in GenBank: a case study in Inocybe (Basidiomycota).

Science.gov (United States)

Ryberg, Martin; Nilsson, R Henrik; Kristiansson, Erik; Töpel, Mats; Jacobsson, Stig; Larsson, Ellen

2008-02-18

The lack of reference sequences from well-identified mycorrhizal fungi often poses a challenge to the inference of taxonomic affiliation of sequences from environmental samples, and many environmental sequences are thus left unidentified. Such unidentified sequences belonging to the widely distributed ectomycorrhizal fungal genus Inocybe (Basidiomycota) were retrieved from GenBank and divided into species that were identified in a phylogenetic context using a reference dataset from an ongoing study of the genus. The sequence metadata of the unidentified Inocybe sequences stored in GenBank, as well as data from the corresponding original papers, were compiled and used to explore the ecology and distribution of the genus. In addition, the relative occurrence of Inocybe was contrasted to that of other mycorrhizal genera. Most species of Inocybe were found to have less than 3% intraspecific variability in the ITS2 region of the nuclear ribosomal DNA. This cut-off value was used jointly with phylogenetic analysis to delimit and identify unidentified Inocybe sequences to species level. A total of 177 unidentified Inocybe ITS sequences corresponding to 98 species were recovered, 32% of which were successfully identified to species level in this study. These sequences account for an unexpectedly large proportion of the publicly available unidentified fungal ITS sequences when compared with other mycorrhizal genera. Eight Inocybe species were reported from multiple hosts and some even from hosts forming arbutoid or orchid mycorrhizae. Furthermore, Inocybe sequences have been reported from four continents and in climate zones ranging from cold temperate to equatorial climate. Out of the 19 species found in more than one study, six were found in both Europe and North America and one was found in both Europe and Japan, indicating that at least many north temperate species have a wide distribution. Although DNA-based species identification and circumscription are associated

TIG (Tungsten Inert Gas) welding

International Nuclear Information System (INIS)

Anon.

2010-01-01

After having recalled the Tungsten Inert Gas process principle and the different alternative TIG processes, the author explains the advantages and limits of this process. The applications and recent developments are given. (O.M.)

The Cosmetic Ingredient Review Program-Expert Safety Assessments of Cosmetic Ingredients in an Open Forum.

Science.gov (United States)

Boyer, Ivan J; Bergfeld, Wilma F; Heldreth, Bart; Fiume, Monice M; Gill, Lillian J

The Cosmetic Ingredient Review (CIR) is a nonprofit program to assess the safety of ingredients in personal care products in an open, unbiased, and expert manner. Cosmetic Ingredient Review was established in 1976 by the Personal Care Products Council (PCPC), with the support of the US Food and Drug Administration (USFDA) and the Consumer Federation of America (CFA). Cosmetic Ingredient Review remains the only scientific program in the world committed to the systematic, independent review of cosmetic ingredient safety in a public forum. Cosmetic Ingredient Review operates in accordance with procedures modeled after the USFDA process for reviewing over-the-counter drugs. Nine voting panel members are distinguished, such as medical professionals, scientists, and professors. Three nonvoting liaisons are designated by the USFDA, CFA, and PCPC to represent government, consumer, and industry, respectively. The annual rate of completing safety assessments accelerated from about 100 to more than 400 ingredients by implementing grouping and read-across strategies and other approaches. As of March 2017, CIR had reviewed 4,740 individual cosmetic ingredients, including 4,611 determined to be safe as used or safe with qualifications, 12 determined to be unsafe, and 117 ingredients for which the information is insufficient to determine safety. Examples of especially challenging safety assessments and issues are presented here, including botanicals. Cosmetic Ingredient Review continues to strengthen its program with the ongoing cooperation of the USFDA, CFA, the cosmetics industry, and everyone else interested in contributing to the process.

Advanced On Board Inert Gas Generation System (OBBIGS), Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Valcor Engineering Corporation proposes to develop an advanced On Board Inert Gas Generation System, OBIGGS, for aircraft fuel tank inerting to prevent hazardous...

New feed ingredients

NARCIS (Netherlands)

Raamsdonk, van L.W.D.; Fels-Klerx, van der H.J.; Jong, de J.

2017-01-01

In the framework of sustainability and a circular economy, new ingredients for feed are desired and, to this end, initiatives for implementing such novel ingredients have been started. The initiatives include a range of different sources, of which insects are of particular interest. Within the

Preliminary Design Report Shippingport Spent Fuel Drying and Inerting System

International Nuclear Information System (INIS)

JEPPSON, D.W.

2000-01-01

A process description and system flow sheets have been prepared to support the design/build package for the Shippingport Spent Fuel Canister drying and inerting process skid. A process flow diagram was prepared to show the general steps to dry and inert the Shippingport fuel loaded into SSFCs for transport and dry storage. Flow sheets have been prepared to show the flows and conditions for the various steps of the drying and inerting process. Calculations and data supporting the development of the flow sheets are included

INERT-MATRIX FUEL: ACTINIDE ''BURNING'' AND DIRECT DISPOSAL

International Nuclear Information System (INIS)

Rodney C. Ewing; Lumin Wang

2002-01-01

Excess actinides result from the dismantlement of nuclear weapons (Pu) and the reprocessing of commercial spent nuclear fuel (mainly 241 Am, 244 Cm and 237 Np). In Europe, Canada and Japan studies have determined much improved efficiencies for burnup of actinides using inert-matrix fuels. This innovative approach also considers the properties of the inert-matrix fuel as a nuclear waste form for direct disposal after one-cycle of burn-up. Direct disposal can considerably reduce cost, processing requirements, and radiation exposure to workers

The Inert and the Noble

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 4; Issue 3. The Inert and the Noble. A G Samuelson. Article-in-a-Box Volume 4 Issue 3 March 1999 pp 3-5 ... Author Affiliations. A G Samuelson1. Department of Inorganic and Physical Chemistry, Indian Institute of Science, Bangalore, India.

First principles study of inert-gas (helium, neon, and argon) interactions with hydrogen in tungsten

Energy Technology Data Exchange (ETDEWEB)

Kong, Xiang-Shan [Key Laboratory of Materials Physics, Institute of Solid State Physics, Chinese Academy of Sciences, P. O. Box 1129, Hefei 230031 (China); Hou, Jie [Key Laboratory of Materials Physics, Institute of Solid State Physics, Chinese Academy of Sciences, P. O. Box 1129, Hefei 230031 (China); University of Science and Technology of China, Hefei 230026 (China); Li, Xiang-Yan [Key Laboratory of Materials Physics, Institute of Solid State Physics, Chinese Academy of Sciences, P. O. Box 1129, Hefei 230031 (China); Wu, Xuebang, E-mail: xbwu@issp.ac.cn [Key Laboratory of Materials Physics, Institute of Solid State Physics, Chinese Academy of Sciences, P. O. Box 1129, Hefei 230031 (China); Liu, C.S., E-mail: csliu@issp.ac.cn [Key Laboratory of Materials Physics, Institute of Solid State Physics, Chinese Academy of Sciences, P. O. Box 1129, Hefei 230031 (China); Chen, Jun-Ling; Luo, G.-N. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China)

2017-04-15

We have systematically evaluated binding energies of hydrogen with inert-gas (helium, neon, and argon) defects, including interstitial clusters and vacancy-inert-gas complexes, and their stable configurations using first-principles calculations. Our calculations show that these inert-gas defects have large positive binding energies with hydrogen, 0.4–1.1 eV, 0.7–1.0 eV, and 0.6–0.8 eV for helium, neon, and argon, respectively. This indicates that these inert-gas defects can act as traps for hydrogen in tungsten, and impede or interrupt the diffusion of hydrogen in tungsten, which supports the discussion on the influence of inert-gas on hydrogen retention in recent experimental literature. The interaction between these inert-gas defects and hydrogen can be understood by the attractive interaction due to the distortion of the lattice structure induced by inert-gas defects, the intrinsic repulsive interaction between inert-gas atoms and hydrogen, and the hydrogen-hydrogen repelling in tungsten lattice.

Comparative Study between Two Schemes of Active-Control-Based Mechatronic Inerter

Directory of Open Access Journals (Sweden)

He Lingduo

2017-01-01

Full Text Available Based on force-current analogy and velocity-voltage analogy in the theory of electromechanical analogy, the inerter is a device that corresponded to the capacitor completely where conquers the nature restriction of mass, what’s more, it is significant to improve the ratio of the inerter’s inertance to its mass for mechanical networks synthesis. And according to the principle of active-control-based mechatronic inerter, we present two implementation schemes. One was based on linear motor, and the other was based on the ball screw and rotary motor. We introduced the implementation methods and established theoretical model of the two schemes, then compared the ratio of the inerter’s inertance to its mass for the two schemes. Finally, we consider the scheme is better which was based on the ball screw and rotary motor.

Reducing Actinide Production Using Inert Matrix Fuels

Energy Technology Data Exchange (ETDEWEB)

Deinert, Mark [Colorado School of Mines, Golden, CO (United States)

2017-08-23

The environmental and geopolitical problems that surround nuclear power stem largely from the longlived transuranic isotopes of Am, Cm, Np and Pu that are contained in spent nuclear fuel. New methods for transmuting these elements into more benign forms are needed. Current research efforts focus largely on the development of fast burner reactors, because it has been shown that they could dramatically reduce the accumulation of transuranics. However, despite five decades of effort, fast reactors have yet to achieve industrial viability. A critical limitation to this, and other such strategies, is that they require a type of spent fuel reprocessing that can efficiently separate all of the transuranics from the fission products with which they are mixed. Unfortunately, the technology for doing this on an industrial scale is still in development. In this project, we explore a strategy for transmutation that can be deployed using existing, current generation reactors and reprocessing systems. We show that use of an inert matrix fuel to recycle transuranics in a conventional pressurized water reactor could reduce overall production of these materials by an amount that is similar to what is achievable using proposed fast reactor cycles. Furthermore, we show that these transuranic reductions can be achieved even if the fission products are carried into the inert matrix fuel along with the transuranics, bypassing the critical separations hurdle described above. The implications of these findings are significant, because they imply that inert matrix fuel could be made directly from the material streams produced by the commercially available PUREX process. Zirconium dioxide would be an ideal choice of inert matrix in this context because it is known to form a stable solid solution with both fission products and transuranics.

INGREDIENT BRANDING - A GROWTH OPPORTUNITY?

OpenAIRE

Anca BUTNARIU

2017-01-01

Co-branding is an increasingly used strategy, consisting of marketing products representing two brands or more. Ingredient branding fits in the scope of co-branding, consisting of the inclusion of key attributes of one brand into another brand as ingredients. Ingredient branding is one of the many brand strategies used in marketing to provide differentiation criteria for the customers. In recent years, its importance and incidence have dramatically increased Extant research provides disparate...

Ingredient and labeling issues associated with allergenic foods.

Science.gov (United States)

Taylor, S L; Hefle, S L

2001-01-01

Foods contain a wide range of food ingredients that serve numerous technical functions. Per capita consumer exposure to most of these food ingredients is rather low with a few notable exceptions such as sugar and starch. Some food ingredients including edible oils, hydrolyzed proteins, lecithin, starch, lactose, flavors and gelatin may, at least in some products, be derived from sources commonly involved in IgE-mediated food allergies. These ingredients should be avoided by consumers with allergies to the source material if the ingredient contains detectable protein residues. Other food ingredients, including starch, malt, alcohol and vinegar, may be derived in some cases from wheat, rye or barley, the grains that are implicated in the causation of celiac disease. If these ingredients contain gluten residues, then they should be avoided by celiac sufferers. A few food ingredients are capable of eliciting allergic sensitization, although these ingredients would be classified as rarely allergenic. These ingredients include carmine, cochineal extract, annatto, tragacanth gum and papain. Food manufacturers should declare the presence of allergenic food ingredients in the ingredient listings on product labels so that allergic consumers can know to avoid these potentially hazardous products.

40 CFR 180.1052 - 2,2,5-trimethyl-3-dichloro-acetyl-1,3-oxazolidine; exemption from the requirement of a tolerance.

Science.gov (United States)

2010-07-01

...-oxazolidine is exempted from the requirement of a tolerance when used as an inert ingredient in formulations... diisobutylthiocarbamate applied to corn fields before the corn plants emerge from the soil with a maximum of 0.5 pound of the inert ingredient per acre. [45 FR 51201, Aug. 1, 1980] ...

Epileptiform activity during inert gas euthanasia of mice.

Science.gov (United States)

Gent, Thomas C; Detotto, Carlotta; Vyssotski, Alexei L; Bettschart-Wolfensberger, Regula

2018-01-01

Carbon dioxide (CO2) is one of the most commonly used euthanasia agents for mice, yet it is highly aversive and nociceptive. Inert gases are a possible alternative, however there are qualitative reports of seizures resulting from exposure. Here we evaluate epileptiform activity caused by inert gases (N2, He, Ar and Xe) and CO2 in mice chronically instrumented for EEG/EMG undergoing single-gas euthanasia. We found that N2, He and Ar caused epileptiform activity in all animals, CO2 in half of animals and no epileptiform activity produced by Xe. Atmospheric O2 concentrations at epileptiform activity onset were significantly higher for CO2 than for all other gases and occurred soon after loss of motion, whereas N2 and Ar epileptiform activity occurred at cessation of neocortical activity. Helium caused the longest epileptiform activity and these commenced significantly before isoelectric EEG. We did not detect any epileptiform activity during active behaviour. Taken together, these results demonstrate that whilst epileptiform activity from inert gases and particularly Ar and N2 are more prevalent than for CO2, their occurrence at the onset of an isoelectric EEG is unlikely to impact on the welfare of the animal. Epileptiform activity from these gases should not preclude them from further investigation as euthanasia agents. The genesis of epileptiform activity from CO2 is unlikely to result from hypoxia as with the inert gases. Helium caused epileptiform activity before cessation of neocortical activity and for a longer duration and is therefore less suitable as an alternative to CO2.

40 CFR 180.1071 - Peanuts, Tree Nuts, Milk, Soybeans, Eggs, Fish, Crustacea, and Wheat; exemption from the...

Science.gov (United States)

2010-07-01

... either an inert or an active ingredient in a pesticide formulation), if such use is in accordance with... the harvested crop has been removed. (7) Soil-directed applications around and adjacent to all plants... use of the following substances as either an inert or an active ingredient in a pesticide formulation...

2nd Workshop on the Nature of the High-Energy Unidentified Sources

CERN Document Server

Cheng, K S; Multiwavelength Approach to Unidentified Gamma-Ray Sources

2005-01-01

Nearly one half of the point-like gamma-ray sources detected by EGRET instrument of the late Compton satellite are still defeating our attempts at identifying them. To establish the origin and nature of these enigmatic sources has become a major problem of current high-energy astrophysics. The second workshop on Multiwavelength Approach to Unidentified Gamma-ray Sources intends to shed new and fresh light on the problem of the nature of these mysterious sources and the objects behind them. The proceedings contain 46 contributed papers in this subject, which cover theoretical models on gamma-ray sources as well as the best multiwavelength strategies for the identification of the promising candidates. The topics of this conference also include energetic phenomena ocurring both in galactic and extragalactic scenarios, phenomena that might lead to the appearance of what we have called high-energy unidentified sources. The book will be of interest for all active researchers in the high-energy astrophysics and rela...

FOOD AS VECTOR FOR NUTRACEUTICAL INGREDIENTS

Directory of Open Access Journals (Sweden)

Bandana Chatterjee

2016-01-01

Full Text Available Now-a-days people consumption habits are changing they are inclined to buy healthy food that fulfills the need of essential nutrients in the body. With increasing educational level, people are becoming ready to accept different types of food & beverages that have added nutritional ingredient. Hence with this change, nutraceutical ingredient is gaining importance. Nutraceutical are those that combine technological and health properties. Nutraceutical Ingredients are substances with clinically confirmed health benefits and have broad applications in foods, beverages, dietary supplements and nutritional preparations. There are huge numbers of ingredients which are still unexplored. They have still not gained popularity in food industry. In this review paper a brief introduction of nutraceutical ingredient, its market and detailed knowledge of- Ginseng, Pine Bark Extract, Seabuckthorn, Buckwheat is mentioned.

Final report of the Cosmetic Ingredient Review Expert Panel amended safety assessment of Calendula officinalis-derived cosmetic ingredients.

Science.gov (United States)

Andersen, F Alan; Bergfeld, Wilma F; Belsito, Donald V; Hill, Ronald A; Klaassen, Curtis D; Liebler, Daniel C; Marks, James G; Shank, Ronald C; Slaga, Thomas J; Snyder, Paul W

2010-01-01

Calendula officinalis extract, C officinalis flower, C officinalis flower extract, C officinalis flower oil, and C officinalis seed oil are cosmetic ingredients derived from C officinalis. These ingredients may contain minerals, carbohydrates, lipids, phenolic acids, flavonoids, tannins, coumarins, sterols and steroids, monoterpenes, sesquiterpenes, triterpenes, tocopherols, quinones, amino acids, and resins. These ingredients were not significantly toxic in single-dose oral studies using animals. The absence of reproductive/developmental toxicity was inferred from repeat-dose studies of coriander oil, with a similar composition. Overall, these ingredients were not genotoxic. They also were not irritating, sensitizing, or photosensitizing in animal or clinical tests but may be mild ocular irritants. The Cosmetic Ingredient Review (CIR) Expert Panel concluded that these ingredients are safe for use in cosmetics in the practices of use and concentration given in this amended safety assessment.

Method of producing hydrogen, and rendering a contaminated biomass inert

Science.gov (United States)

Bingham, Dennis N [Idaho Falls, ID; Klingler, Kerry M [Idaho Falls, ID; Wilding, Bruce M [Idaho Falls, ID

2010-02-23

A method for rendering a contaminated biomass inert includes providing a first composition, providing a second composition, reacting the first and second compositions together to form an alkaline hydroxide, providing a contaminated biomass feedstock and reacting the alkaline hydroxide with the contaminated biomass feedstock to render the contaminated biomass feedstock inert and further producing hydrogen gas, and a byproduct that includes the first composition.

Passive and active vibration isolation systems using inerter

Science.gov (United States)

Alujević, N.; Čakmak, D.; Wolf, H.; Jokić, M.

2018-03-01

This paper presents a theoretical study on passive and active vibration isolation schemes using inerter elements in a two degree of freedom (DOF) mechanical system. The aim of the work is to discuss basic capabilities and limitations of the vibration control systems at hand using simple and physically transparent models. Broad frequency band dynamic excitation of the source DOF is assumed. The purpose of the isolator system is to prevent vibration transmission to the receiving DOF. The frequency averaged kinetic energy of the receiving mass is used as the metric for vibration isolation quality. It is shown that the use of inerter element in the passive vibration isolation scheme can enhance the isolation effect. In the active case, a feedback disturbance rejection scheme is considered. Here, the error signal is the receiving body absolute velocity which is directly fed to a reactive force actuator between the source and the receiving bodies. In such a scheme, the so-called subcritical vibration isolation problems exist. These problems are characterised by the uncoupled natural frequency of the receiving body larger than the uncoupled natural frequency of the source body. In subcritical vibration isolation problems, the performance of the active control is limited by poor stability margins. This is because the stable feedback gain is restricted in a narrow range between a minimum and a maximum. However, with the inclusion of an inerter in the isolator, one of the two stability margins can be opened. This enables large, theoretically unlimited negative feedback gains and large active damping of the receiving body vibration. A simple expression for the required inertance is derived.

Inert carrier drying and coating process

International Nuclear Information System (INIS)

1980-01-01

An inert carrier process is described for drying radioactive (particularly low level) waste material and for incorporating the dry material into a binder matrix from which the dried material will not be leached. Experimental details, and examples of the carrier and binder materials, are given. (U.K.)

Inactive ingredient Search for Approved Drug Products

Data.gov (United States)

U.S. Department of Health & Human Services — According to 21 CFR 210.3(b)(8), an inactive ingredient is any component of a drug product other than the active ingredient. Only inactive ingredients in the final...

temperature fluctuation inside inert atmosphere silos

African Journals Online (AJOL)

... the two silos for twenty-eight (28) months of storage were recorded in order to monitor temperature fluctuation at different sections inside the inert atmosphere silos loaded with two varieties of wheat namely LACRIWHT-2 (Cettia) and LACRIWHT-4 (Atilla-Gan-Atilla) from Lake Chad Research Institute, Maiduguri, Nigeria.

Nanotoxicity of Inert Materials: The Case of Gold, Silver and Iron.

Science.gov (United States)

Umair, Muhammad; Javed, Ibrahim; Rehman, Mubashar; Madni, Asadullah; Javeed, Aqeel; Ghafoor, Aamir; Ashraf, Muhammad

2016-01-01

Nanotechnology has opened a new horizon of research in various fields including applied physics, chemistry, electronics, optics, robotics, biotechnology and medicine. In the biomedical field, nanomaterials have shown remarkable potential as theranostic agents. Materials which are considered inert are often used in nanomedicine owning to their nontoxic profile. At nanoscale, these inert materials have shown unique properties that differ from bulk and dissolved counterparts. In the case of metals, this unique behavior not only imparts paramount advantages but also confers toxicity due to their unwanted interaction with different cellular processes. In the literature, the toxicity of nanoparticles made from inert materials has been investigated and many of these have revealed toxic potential under specific conditions. The surge to understand underlying mechanism of toxicity has increased and different means have been employed to overcome toxicity problems associated with these agents. In this review, we have focused nanoparticles of three inert metallic materials i.e. gold, silver and iron as these are regarded as biologically inert in the bulk and dissolved form. These materials have gained wider research interest and studies indicating the toxicity of these materials are also emerging. Oxidative stress, physical binding and interference with intracellular signaling are the major role player in nanotoxicity and their predominance is highly dependent upon size, surface coating and administered dose of nanoparticles. Current strategies to overcome toxicity have also been reviewed in the light of recent literature. The authors also suggested that uniform testing standards and well-designed studies are needed to evaluate nanotoxicity of these materials that are otherwise considered as inert. This article is open to POST-PUBLICATION REVIEW. Registered readers (see "For Readers") may comment by clicking on ABSTRACT on the issue's contents page.

Dry boxes and inert atmosphere techniques

International Nuclear Information System (INIS)

Bartak, D.E.

1987-01-01

Practitioners need to conduct experiments with molten salts in an inert atmosphere owing to the chemical reactivity of these media. Most fused salt solvent systems show reactivity to water and/or oxygen, which results in significant chemical changes in the properties of these solvents. Although several studies on the nature of an oxygen/oxide electrode in this melt have been reported, the reactions have not been fully understood because of apparent water contamination in many cases. Nitrate melt systems are also hygroscopic; for example, the LiNO 3 -KNO 3 eutectic (177 0 C) absorbs water to at least 0.2% by weight. The result is that the electrochemistry of heavier, electropositive metal ions has been significantly altered. In addition, trace amounts of water have been shown to significantly affect the oxygen-oxide redox chemistry in NaNO 3 -KNO 3 melts (250 0 C). The haloaluminates, which include AlCl 3 -NaCl (175 0 C), as well as AlCl 3 -organic salt binaries are particularly sensitive to the presence of both oxygen and moisture. Oxygen is a strong oxidant in the fused hydroxide systems with formation of superoxide ion from either oxide or water. This chapter describes general, inert atmosphere techniques which can be used by the molten salt experimentalist. Because of the limitations of volatility, vacuum manipulations are not considered. Rather, the use of glove boxes, glove bags, and inert bench-top techniques are discussed. The areas covered are: glove box and bag equipment, operation and maintenance of glove boxes and glove bags, and common operations conducted inside glove boxes

Identification of the unidentified deceased and locating next of kin: experience with a UID web site page, Fulton County, Georgia.

Science.gov (United States)

Hanzlick, Randy

2006-06-01

Medical examiner and coroner offices may face difficulties in trying to achieve identification of deceased persons who are unidentified or in locating next of kin for deceased persons who have been identified. The Fulton County medical examiner (FCME) has an office web site which includes information about unidentified decedents and cases for which next of kin are being sought. Information about unidentified deceased and cases in need of next of kin has been posted on the FCME web site for 3 years and 1 year, respectively. FCME investigators and staff medical examiners were surveyed about the web site's usefulness for making identifications and locating next of kin. No cases were recalled in which the web site led to making an identification. Two cases were reported in which next of kin were located, and another case involved a missing person being ruled out as one of the decedents. The web site page is visited by agencies interested in missing and unidentified persons, and employees do find it useful for follow-up because information about all unidentified decedents is located and easily accessible, electronically, in a single location. Despite low yield in making identifications and locating next of kin, the UID web site is useful in some respects, and there is no compelling reason to discontinue its existence. It is proposed that UID pages on office web sites be divided into "hot" (less than 30 days, for example) and "warm" (31 days to 1 year, for example) cases and that cases older than a year be designated as "cold cases." It is conceivable that all unidentified deceased cases nationally could be placed on a single web site designed for such purposes, to remain in public access until identity is established and confirmed.

Techniques for optimizing inerting in electron processors

International Nuclear Information System (INIS)

Rangwalla, I.J.; Korn, D.J.; Nablo, S.V.

1993-01-01

The design of an ''inert gas'' distribution system in an electron processor must satisfy a number of requirements. The first of these is the elimination or control of beam produced ozone and NO x which can be transported from the process zone by the product into the work area. Since the tolerable levels for O 3 in occupied areas around the processor are 3 in the beam heated process zone, or exhausting and dilution of the gas at the processor exit. The second requirement of the inerting system is to provide a suitable environment for completing efficient, free radical initiated addition polymerization. The competition between radical loss through de-excitation and that from O 2 quenching must be understood. This group has used gas chromatographic analysis of electron cured coatings to study the trade-offs of delivered dose, dose rate and O 2 concentrations in the process zone to determine the tolerable ranges of parameter excursions for production quality control purposes. These techniques are described for an ink coating system on paperboard, where a broad range of process parameters have been studied (D, D radical, O 2 ). It is then shown how the technique is used to optimize the use of higher purity (10-100 ppm O 2 ) nitrogen gas for inerting, in combination with lower purity (2-20,000 ppm O 2 ) non-cryogenically produced gas, as from a membrane or pressure swing adsorption generators. (author)

A purification process for an inert gas system

International Nuclear Information System (INIS)

Raj, S.S.; Samanta, S.K.; Jain, N.G.; Deshingkar, D.S.; Ramaswamy, M.

1984-01-01

Special inert atmosphere is desired inside hot cells used for handling radioactive materials. In this report, details of experiments conducted to generate data required for the design of a system for maintaining very low levels of organic and acid vapours, oxygen and moisture in a nitrogen gas inert atmosphere, are described. Several grades of activated charcoals impregnated with 1% KOH were studied for the adsorption of acidic and organic vapours. A Pd/Al 2 O 3 catalyst was developed to remove oxygen with greater than 90% efficiency. For the removal of moisture, a regenerable molecular sieve 4A dual-bed was provided. Based on the performance data thus generated, an integrated purification system for nitrogen gas is proposed. (author)

Adsorption and desorption of radioactive inert gases in various materials

International Nuclear Information System (INIS)

Butkus, D.

1999-01-01

Peculiarities of the 85 Kr and 133 Xe adsorption and desorption processes in active carbon and paraffin are considered in the work. During the desorption process, the distribution of 85 Kr and 133 Xe atoms in active carbon particles is uneven: atoms in narrow micropores desorb the last. It is shown that by changing adsorption conditions the presence time of radioactive inert gases in an active carbon can be prolonged. The adsorption and desorption processes change in the adsorbent, which changes its aggregation state: adsorption occurs in a liquid absorbent and desorption - in a solid absorbent. Paraffin is just such an absorbent changing its aggregation state with low energy losses. It has been obtained that 133 Xe accumulates less in liquid paraffin that in an active carbon. The absorption of 85 Kr in paraffin is larger than in an active carbon (at 18-20 degrees Celsius), while desorption is slower. The velocity of radioactive inert gas atom motion in different places of a solid paraffin sample is different - it increases approaching the borders of the sample. Prolongation of the desorption time of radioactive inert gases from adsorbents and adsorbents in many cases is of a practical importance. In this work, it has been shown by model experiments that the intensity of adsorption and desorption processes for the same sorbents can be changed. Desorption intensity changes are related to the distribution of gas atoms on the surface of particles and in micropores. Desorption velocity decreases if inert gas atoms having entered micropores are 'closed' by condensed liquids in the environment. In this case an inert gas atom diffuses within the whole particle volume or through the condensed liquid. Radioactive inert gases 85 Kr and 133 Xe are absorbed not only in liquid paraffin but in solid one as well. Therefore, after a paraffin sample is hermetically closed in a glass dish, 85 Kr (gas) having diffused from this sample is repeatedly absorbed in it. The 85 Kr

Preparation of mesoporous zirconia microspheres as inert matrix

Energy Technology Data Exchange (ETDEWEB)

Guo, Ting [State Key Laboratory of New Ceramics and Fine Processing, Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing, 100084 (China); Wang, Chen; Lv, Jinlong [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing, 100084 (China); Liang, Tongxiang, E-mail: txliang@tsinghua.edu.cn [State Key Laboratory of New Ceramics and Fine Processing, Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing, 100084 (China)

2016-12-01

Mesoporous zirconia microspheres, with a diameter of 900 μm, were prepared as an inert accelerator driven system (ADS) transmutation element matrix by the sol-gel method. The purpose of mesopores is to improve the adsorption capacity of inert matrix fuel (IMF) for minor actinides. The study indicated that the mesoporous zirconia performance was improved after the microspheres were hydrothermally treated at 150 °C, the specific surface area increased from 28.29 m{sup 2}/g to 61.28 m{sup 2}/g, and hydrothermal treatment avoided the cracking of the microspheres. Pre-decomposition of the organics during the hydrothermal process stabilized the mesoporous structure. The average pore diameter of mesoporous microsphere was 14.3 nm. - Highlights: • Mesoporous zirconia microspheres with a diameter of 900 μm were prepared as ADS transmutation element inert matrix. • The mesoporous performance was improved after the microspheres were hydrothermally treated at 150 °C. • The specific surface area increased from 28.29 m{sup 2}/g to 61.28 m{sup 2}/g. • The hydrothermal treatment could avoid the cracking of the microspheres. • The specific surface area of mesoporous microsphere was 61.28 m{sup 2}/g and the average pore diameter was 14.3 nm.

21 CFR 701.3 - Designation of ingredients.

Science.gov (United States)

2010-04-01

... declaration of ingredients is thereby required to be used in conjunction with products of both the old and new formulations, the labeling shall declare the ingredients of both the old and new formulations separately in a... paragraph is inapplicable to any ingredient mentioned in advertising, or in labeling other than in the...

Radiochemical and inert gas analyses

International Nuclear Information System (INIS)

Andrews, J.N.

1985-01-01

The subject is discussed under the headings: introduction (radioelement solution in groundwaters; U and Th; Ra and Rn; atmospheric and radiogenic solution in groundwaters; atmosphere derived gases; radiogenic helium; radiogenic argon; biogenic gases); analytical methods (sampling; U-content and 234 U/ 238 U activity ratio; 222 Ru; 226 Ra; dissolved inert gases; 4 He in core samples); the gamma spectrometric determination of U,Th and K. Results are presented and discussed. (U.K.)

THE SEARCH FOR BLAZARS AMONG THE UNIDENTIFIED EGRET gamma-RAY SOURCES

Directory of Open Access Journals (Sweden)

Pieter J. Meintjes

2013-12-01

Full Text Available In this paper we report the results of a multi-wavelength follow-up study of selected flat spectrum extragalactic radio-optical counterparts within the error boxes of 13 unidentified EGRET sources. Two of these previously unidentified counterparts have been selected for optical photometric and spectroscopic follow-up studies. Spectroscopic observations made with the 4.1m SOAR telescope at Cerro Pachón, Chile, showed that the spectra of the optical counterparts of 3EG J0821−5814 (PKS J0820−5705 and 3EG J0706−3837 (PMN J0710−3835 correspond to a flat spectrum radio quasar (FSRQ and LINER-Seyfert I galaxy respectively. Optical photometry of these sources, performed with the 1.0m telescope at Sutherland (South-Africa shows noticeable intranight variability for PKS J0820−5705, as well as a 5 sigma variation of the mean brightness in the R-filter over a timescale of three nights. Significant variability has been detected in the B-band for PMN J0710−3835 as well. The gamma-ray spectral indices of all 13 candidates range between 2–3, correlating well with the BL Lacs and FSRQs detected with Fermi-LAT in the first 11 months of operation.

21 CFR 333.310 - Acne active ingredients.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Acne active ingredients. 333.310 Section 333.310... FOR HUMAN USE TOPICAL ANTIMICROBIAL DRUG PRODUCTS FOR OVER-THE-COUNTER HUMAN USE Topical Acne Drug Products § 333.310 Acne active ingredients. The active ingredient of the product consists of any of the...

Ethanol Dehydration by Evaporation and Diffusion in an Inert Gas Layer

Energy Technology Data Exchange (ETDEWEB)

In-Sick, Chung; Kyu-Min, Song [Korea Advanced Institute of Science and Technology, Taejeon (Korea, Republic of); Won-Hi, Hong; Ho-Nam, Chang [Korea Advanced Institute of Science and Technology, Taejeon (Korea, Republic of)

1994-08-01

Ethanol dehydration of azeotropic mixture was performed by using diffusion distillation apparatus consisting of a wetted-wall column with two concentric tubes. Ethanol-water mixtures evaporated below the boiling point was separated during the diffusion through the gap filled with an inert gas. As the temperature difference between evaporation part and condensation part was increased, the total flux increased but the selectivity decreased. The effect of the annular width on the selectivity was not significant but the total flux was decreased with decreases in the annular width. Inert gas has an effect on the diffusivity of evaporated gas components. The total flux in case of helium as inert gas was larger than that in case of air but the selectivity in case of using helium was lower. (author). 14 refs. 1 tab. 12 figs.

Inerting of a Vented Aircraft Fuel Tank Test Article with Nitrogen-Enriched Air

National Research Council Canada - National Science Library

Burns, Michael

2001-01-01

...) required to inert a vented aircraft fuel tank. NEA, generated by a hollow fiber membrane gas separation system, was used to inert a laboratory fuel tank with a single vent on top designed to simulate a transport category airplane fuel tank...

Ignition of a reactive solid by an inert hot spot

OpenAIRE

Liñán Martínez, Amable; Kindelan Gómez, Manuel

1981-01-01

A theoretical analysis is presented for the description of the ignition of a reactive media by inert hot bodies of finite size, when the activation energy of the reaction is large. The analysis leads to closed-form relations for the minimum "critical" size of the hot spot resulting in ignition and for the ignition time by hot spots of supercritical size. The analysis is carried out, first, for inert spots with heat conductivities and diff usivities of the order of those of the reactive media,...

Analysis of Ingredient Lists to Quantitatively Characterize ...

Science.gov (United States)

The EPA’s ExpoCast program is developing high throughput (HT) approaches to generate the needed exposure estimates to compare against HT bioactivity data generated from the US inter-agency Tox21 and the US EPA ToxCast programs. Assessing such exposures for the thousands of chemicals in consumer products requires data on product composition. This is a challenge since quantitative product composition data are rarely available. We developed methods to predict the weight fractions of chemicals in consumer products from weight fraction-ordered chemical ingredient lists, and curated a library of such lists from online manufacturer and retailer sites. The probabilistic model predicts weight fraction as a function of the total number of reported ingredients, the rank of the ingredient in the list, the minimum weight fraction for which ingredients were reported, and the total weight fraction of unreported ingredients. Weight fractions predicted by the model compared very well to available quantitative weight fraction data obtained from Material Safety Data Sheets for products with 3-8 ingredients. Lists were located from the online sources for 5148 products containing 8422 unique ingredient names. A total of 1100 of these names could be located in EPA’s HT chemical database (DSSTox), and linked to 864 unique Chemical Abstract Service Registration Numbers (392 of which were in the Tox21 chemical library). Weight fractions were estimated for these 864 CASRN. Using a

TIG (Tungsten Inert Gas) welding; Le soudage TIG

Energy Technology Data Exchange (ETDEWEB)

Anon.

2010-09-15

After having recalled the Tungsten Inert Gas process principle and the different alternative TIG processes, the author explains the advantages and limits of this process. The applications and recent developments are given. (O.M.)

Photoinduced C-C Cross-Coupling of Aryl Chlorides and Inert Arenes

Directory of Open Access Journals (Sweden)

Lele Wang

2016-01-01

Full Text Available Here we report a facile, efficient, and catalyst-free method to realize C-C cross-coupling of aryl chlorides and inert arenes under UV light irradiation. The aryl radical upon homolytic cleavage of C-Cl bond initiated the nucleophilic substitution reaction with inert arenes to give biaryl products. This mild reaction mode can also be applied to other synthetic reactions, such as the construction of C-N bonds and trifluoromethylated compounds.

Inerting ballast tanks

Energy Technology Data Exchange (ETDEWEB)

Baes, Gabriel L.; Bronneberg, Jos [SBM Offshore, AA Schiedam (Netherlands); Barros, Maria A.S.D. de [Universidade Estadual de Maringa (UEM), PR (Brazil)

2012-07-01

This report expands upon the work conducted by SBM Offshore to develop a tank preservation treatment, which is intended to achieve a service life of 30 years. This work focuses on the corrosion problems, in the ballast tanks, based on new built hulls, both for the Gas Exploration Market, the FLNG - Floating Liquefied Natural Gas, and for the Oil Exploration market - FPSO's - Floating Production Storage and offloading Units. Herein, the corrosion rate input comes from the various references related to the process of nitrogen injection, which is expected to extend the vessel's time life. The essential elements of this solution comprise the deoxygenation process, corrosion models, coating effects, tests from laboratory, shipboard tests, corrosion institutes and regulations applicable to the operation. The best corrosion protection system for ballast tanks area combines a coating system and an inert gas system. The condition of the tanks will be dependent upon the level of protection applied to the steel structure, including, but not limited to coating, cathodic protection, etc. There is a need for products which extend the life time. It is not sufficient, only have good theoretical base for the corrosion and an excellent treatment system. In addition, the design of the ships structure must also eliminate the presence of local stress concentrations which can result in fatigue cracking and rupture of the protective coating barrier starting the corrosion. As a direct result of this, more problems in corrosion can be mitigated, vessels can have a better corrosion performance with less maintenance and repairs to coating systems in ballast tanks. Furthermore ships will be positively impacted operationally due to less frequent dry docking. There is a huge potential in the application of inert gas to combat the corrosion rate inside the ballast tanks, one of the most corrosive environments on earth. This application can have a direct impact on vessel structure

Helium in inert matrix dispersion fuels

International Nuclear Information System (INIS)

Veen, A. van; Konings, R.J.M.; Fedorov, A.V.

2003-01-01

The behaviour of helium, an important decay product in the transmutation chains of actinides, in dispersion-type inert matrix fuels is discussed. A phenomenological description of its accumulation and release in CERCER and CERMET fuel is given. A summary of recent He-implantation studies with inert matrix metal oxides (ZrO 2 , MgAl 2 O 4 , MgO and Al 2 O 3 ) is presented. A general picture is that for high helium concentrations helium and vacancy defects form helium clusters which convert into over-pressurized bubbles. At elevated temperature helium is released from the bubbles. On some occasions thermal stable nano-cavities or nano-pores remain. On the basis of these results the consequences for helium induced swelling and helium storage in oxide matrices kept at 800-1000 deg. C will be discussed. In addition, results of He-implantation studies for metal matrices (W, Mo, Nb and V alloys) will be presented. Introduction of helium in metals at elevated temperatures leads to clustering of helium to bubbles. When operational temperatures are higher than 0.5 melting temperature, swelling and helium embrittlement might occur

Testes de toxicidade aguda através de bioensaios no extrato solubilizado dos resíduos classe II A - não inertes e classe II B - inertes Acute toxicity tests by bioassays applied to the solubilized extracts of solid wastes class II A - non inerts and class II B - inerts

Directory of Open Access Journals (Sweden)

Nébora Liz Vendramin Brasil Rodrigues

2007-03-01

Full Text Available A grande diversidade de substâncias potencialmente tóxicas contribuem para a deterioração do meio ambiente. O objetivo deste trabalho foi propor a utilização de bioensaios, através de testes de toxicidade aguda com Daphnia magna e Vibrio fischeri, como mais um parâmetro a ser analisado no extrato solubilizado dos resíduos que, segundo a NBR 10004/04 fossem classificados como classe II A - não inertes ou classe II B - inertes. Realizaram-se, também, testes de toxicidade no drenado dos aterros classe II A e II B. Verificou-se que a toxicidade foi constatada nos extratos solubilizados dos 18 resíduos analisados e que, apenas três das amostras estariam próprias para lançamento, ou seja os resíduos 04, 14 e 15. Já, a toxicidade encontrada no drenado dos aterros, ficou muito superior do que a toxicidade de cada extrato solubilizado analisado separadamente.A great diversity of substances potencially toxic contributes to the deterioration of the environment. The aim of this research was to propose the use of bioassays using Daphnia magna and Vibrio fischeri, as another parameter to be analyzed in the solubilized extraction of waste according to NBR 10004/04 and classified as class II A - non inerts or class II B - inerts. Besides, another test was performed to measure the level of toxicity in the drainage of the landfill class II A and II B. It was verified that the toxicity found in the solubilized extracts of the 18 wastes analysed.Only 3 wastes (04, 14 and 15 were within the emission limits. On the other hand the toxicity found in the drainage of the landfill, from which all the samples came from, was much higher than the individual one.

X-ray Studies of Unidentified Galactic TeV Gamma-ray Sources

Science.gov (United States)

Pühlhofer, Gerd

2009-05-01

Many of the recently discovered Galactic TeV sources remain unidentified to date. A large fraction of the sources is possibly associated with relic pulsar wind nebula (PWN) systems. One key question here is the maximum energy (beyond TeV) attained in the compact PWNe. Hard X-ray emission can trace those particles, but current non-focussing X-ray instruments above 10 keV have difficulties to deconvolve the hard pulsar spectrum from its surrounding nebula. Some of the new TeV sources are also expected to originate from middle-aged and possibly even from old supernova remnants (SNR). But no compelling case for such an identification has been found yet. In established young TeV-emitting SNRs, X-ray imaging above 10 keV could help to disentangle the leptonic from the hadronic emission component in the TeV shells, if secondary electrons produced in hadronic collisions can be effectively detected. As SNRs get older, the high energy electron component is expected to fade away. This may allow to verify the picture through X-ray spectral evolution of the source population. Starting from the lessons we have learned so far from X-ray follow-up observations of unidentified TeV sources, prospects for Simbol-X to resolve open questions in this field will be discussed.

X-ray Studies of Unidentified Galactic TeV Gamma-ray Sources

International Nuclear Information System (INIS)

Puehlhofer, Gerd

2009-01-01

Many of the recently discovered Galactic TeV sources remain unidentified to date. A large fraction of the sources is possibly associated with relic pulsar wind nebula (PWN) systems. One key question here is the maximum energy (beyond TeV) attained in the compact PWNe. Hard X-ray emission can trace those particles, but current non-focussing X-ray instruments above 10 keV have difficulties to deconvolve the hard pulsar spectrum from its surrounding nebula.Some of the new TeV sources are also expected to originate from middle-aged and possibly even from old supernova remnants (SNR). But no compelling case for such an identification has been found yet. In established young TeV-emitting SNRs, X-ray imaging above 10 keV could help to disentangle the leptonic from the hadronic emission component in the TeV shells, if secondary electrons produced in hadronic collisions can be effectively detected. As SNRs get older, the high energy electron component is expected to fade away. This may allow to verify the picture through X-ray spectral evolution of the source population.Starting from the lessons we have learned so far from X-ray follow-up observations of unidentified TeV sources, prospects for Simbol-X to resolve open questions in this field will be discussed.

Numerical analysis on hydrogen stratification and post-inerting of hydrogen risk

International Nuclear Information System (INIS)

Peng, Cheng; Tong, Lili; Cao, Xuewu

2016-01-01

Highlights: • A three-dimensional computational model was built and the applicability was discussed. • The formation of helium stratification was further studied. • Three influencing factors on the post-inerting of hydrogen risk were analyzed. - Abstract: In the case of severe accidents, the risk of hydrogen explosion threatens the integrity of the nuclear reactor containment. According to nuclear regulations, hydrogen control is required to ensure the safe operation of the nuclear reactor. In this study, the method of Computational Fluid Dynamics (CFD) has been applied to analyze process of hydrogen stratification and the post-inerting of hydrogen risk in the Large-Scale Gas Mixing Facility. A three-dimensional computational model was built and the applicability of different turbulence models was discussed. The result shows that the helium concentration calculated by the standard k–ε turbulence model is closest to the experiment data. Through analyzing the formation of helium stratification at different injection velocities, it is found that when the injection mass flow is constant and the injection velocity of helium increases, the mixture of helium and air is enhanced while there is rarely influence on the formation of helium stratification. In addition, the influences of mass flow rate, injection location and direction and inert gas on the post-inerting of hydrogen risk have been analyzed and the results are as follows: with the increasing of mass flow rate, the mitigation effect of nitrogen on hydrogen risk will be further improved; there is an obvious local difference between the mitigation effects of nitrogen on hydrogen risk in different injection directions and locations; when the inert gas is injected at the same mass flow rate, the mitigation effect of steam on hydrogen risk is better than that of nitrogen. This study can provide technical support for the mitigation of hydrogen risk in the small LWR containment.

Isolation of an unidentified pink-pigmented bacterium in a clinical specimen.

OpenAIRE

Odugbemi, T; Nwofor, C; Joiner, K T

1988-01-01

An unidentified pink-pigmented bacterium isolated from a clinical specimen is reported. The organism was oxidase, urease, and catalase positive; it grew on Thayer-Martin and MacConkey media. The isolate is possibly similar to an unnamed taxon (G.L. Gilardi and Y.C. Faur, J. Clin. Microbiol. 20:626-629, 1984); however, it had unique characteristics of nonmotility with no flagellum detectable and was a gram-negative coccoid with a few rods in pairs and negative for starch hydrolysis.

Isolation of an unidentified pink-pigmented bacterium in a clinical specimen.

Science.gov (United States)

Odugbemi, T; Nwofor, C; Joiner, K T

1988-05-01

An unidentified pink-pigmented bacterium isolated from a clinical specimen is reported. The organism was oxidase, urease, and catalase positive; it grew on Thayer-Martin and MacConkey media. The isolate is possibly similar to an unnamed taxon (G.L. Gilardi and Y.C. Faur, J. Clin. Microbiol. 20:626-629, 1984); however, it had unique characteristics of nonmotility with no flagellum detectable and was a gram-negative coccoid with a few rods in pairs and negative for starch hydrolysis.

Mixed Inert scalar triplet dark matter, radiative neutrino masses and leptogenesis

Directory of Open Access Journals (Sweden)

Wen-Bin Lu

2017-11-01

Full Text Available The neutral component of an inert scalar multiplet with hypercharge can provide a stable dark matter particle when its real and imaginary parts have a splitting mass spectrum. Otherwise, a tree-level dark-matter-nucleon scattering mediated by the Z boson will be much above the experimental limit. In this paper we focus on a mixed inert scalar triplet dark matter scenario where a complex scalar triplet with hypercharge can mix with another real scalar triplet without hypercharge through their renormalizable coupling to the standard model Higgs doublet. We consider three specified cases that carry most of the relevant features of the full parameter space: (i the neutral component of the real triplet dominates the dark matter particle, (ii the neutral component of the complex triplet dominates the dark matter particle; and (iii the neutral components of the real and complex triplets equally constitute the dark matter particle. Subject to the dark matter relic abundance and direct detection constraint, we perform a systematic study on the allowed parameter space with particular emphasis on the interplay among triplet-doublet terms and gauge interactions. In the presence of these mixed inert scalar triplets, some heavy Dirac fermions composed of inert fermion doublets can be utilized to generate a tiny Majorana neutrino mass term at one-loop level and realize a successful leptogenesis for explaining the cosmic baryon asymmetry.

An accurate and precise representation of drug ingredients.

Science.gov (United States)

Hanna, Josh; Bian, Jiang; Hogan, William R

2016-01-01

In previous work, we built the Drug Ontology (DrOn) to support comparative effectiveness research use cases. Here, we have updated our representation of ingredients to include both active ingredients (and their strengths) and excipients. Our update had three primary lines of work: 1) analysing and extracting excipients, 2) analysing and extracting strength information for active ingredients, and 3) representing the binding of active ingredients to cytochrome P450 isoenzymes as substrates and inhibitors of those enzymes. To properly differentiate between excipients and active ingredients, we conducted an ontological analysis of the roles that various ingredients, including excipients, have in drug products. We used the value specification model of the Ontology for Biomedical Investigations to represent strengths of active ingredients and then analyzed RxNorm to extract excipient and strength information and modeled them according to the results of our analysis. We also analyzed and defined dispositions of molecules used in aggregate as active ingredients to bind cytochrome P450 isoenzymes. Our analysis of excipients led to 17 new classes representing the various roles that excipients can bear. We then extracted excipients from RxNorm and added them to DrOn for branded drugs. We found excipients for 5,743 branded drugs, covering ~27% of the 21,191 branded drugs in DrOn. Our analysis of active ingredients resulted in another new class, active ingredient role. We also extracted strengths for all types of tablets, capsules, and caplets, resulting in strengths for 5,782 drug forms, covering ~41% of the 14,035 total drug forms and accounting for ~97 % of the 5,970 tablets, capsules, and caplets in DrOn. We represented binding-as-substrate and binding-as-inhibitor dispositions to two cytochrome P450 (CYP) isoenzymes (CYP2C19 and CYP2D6) and linked these dispositions to 65 compounds. It is now possible to query DrOn automatically for all drug products that contain active

AGENTES INERTES PARA CONTOLE DE TOMBAMENTO EM SEMENTEIRAS DE OLERÍCOLAS

Directory of Open Access Journals (Sweden)

Ricardo Silveiro Balardin

1994-01-01

Full Text Available RESUMO Este trabalho foi conduzido com o objetivo de avaliar o comportamento de materiais inertes para controle de tombamento durante a emergência. Os tratamentos foram cobertura do sulco de semeadura com areia e serragem, tratamento químico com brometo de metila e uma testemunha. Os parâmetros avaliados foram percentagem e velocidade de emergência, percentagem de tombamento de pré e pós-emergência. Os dados obtidos permitiram concluir que, dentre os materiais inertes testados, a areia pode constituir-se em uma alternativa eficiente no controle do tombamento em sementeiras de repolho e beterraba, pois permitiu o maior número de plântulas emergidas e o menor número de plântulas tombadas não alterando a velocidade de emergência, enquanto que nas sementeiras de alface a utilização dos materiais inertes prejudicou a emergência normal das plântulas, não se constituindo em agente de controle eficiente.

Inert gas thrusters

Science.gov (United States)

Kaufman, H. R.; Robinson, R. S.

1980-01-01

Some advances in component technology for inert gas thrusters are described. The maximum electron emission of a hollow cathode with Ar was increased 60-70% by the use of an enclosed keeper configuration. Operation with Ar, but without emissive oxide, was also obtained. A 30 cm thruster operated with Ar at moderate discharge voltages give double-ion measurements consistent with a double ion correlation developed previously using 15 cm thruster data. An attempt was made to reduce discharge losses by biasing anodes positive of the discharge plasma. The reason this attempt was unsuccessful is not yet clear. The performance of a single-grid ion-optics configuration was evaluated. The ion impingement on the single grid accelerator was found to approach the value expected from the projected blockage when the sheath thickness next to the accelerator was 2-3 times the aperture diameter.

An electromagnetic inerter-based vibration suppression device

International Nuclear Information System (INIS)

Gonzalez-Buelga, A; Clare, L R; Neild, S A; Jiang, J Z; Inman, D J

2015-01-01

This paper describes how an inerter-based device for structural vibration suppression can be realized using an electromagnetic transducer such as a linear motor. When the motor shaft moves, a difference of voltage is generated across the transducer coil. The voltage difference is proportional to the relative velocity between its two terminals. The electromagnetic transducer will exert a force proportional to current following the Lorentz principle if the circuit is closed around the transducer coil. If an electronic circuit consisting of a capacitor, an inductance and a resistance with the appropriate configuration is connected, the resulting force reflected back into the mechanical domain is equivalent to that achieved by a mechanical inerter-based device. The proposed configuration is easy to implement and very versatile, provided a high quality conversion system with negligible losses. With the use of electromagnetic devices, a new generation of vibration absorbers can be realized, for example in the electrical domain it would be relatively uncomplicated to synthesize multi-frequency or real time tunable vibration absorbers by adding electrical components in parallel. In addition by using resistance emulators in the electrical circuits, part of the absorbed vibration energy can be converted into usable power. Here an electromagnetic tuned inerter damper (E-TID) is tested experimentally using real time dynamic substructuring. A voltage compensation unit was developed in order to compensate for coil losses. This voltage compensation unit requires power, which is acquired through harvesting from the vibration energy using a resistance emulator. A power balance analysis was developed in order to ensure the device can be self sufficient. Promising experimental results, using this approach, have been obtained and are presented in this paper. The ultimate goal of this research is the development of autonomous electromagnetic vibration absorbers, able to harvest energy

Thermodilution versus inert gas rebreathing for estimation of effective pulmonary blood flow

DEFF Research Database (Denmark)

Christensen, P; Clemensen, P; Andersen, P K

2000-01-01

To compare measurements of the effective pulmonary blood flow (Qep, i.e., nonshunted fraction of cardiac output, Qt) by the inert gas rebreathing (RB) method and the thermodilution (TD) technique in critically ill patients.......To compare measurements of the effective pulmonary blood flow (Qep, i.e., nonshunted fraction of cardiac output, Qt) by the inert gas rebreathing (RB) method and the thermodilution (TD) technique in critically ill patients....

Inert atmosphere system for plutonium processing gloveboxes

International Nuclear Information System (INIS)

Bogard, C.F.; Calkins, K.W.; Rogers, R.F.

1975-01-01

Recent efforts to reduce fire hazards in plutonium processing operations are described. In such operations, the major environmental controls are developed through various kinds of glovebox systems. In evaluating the air-atmosphere glovebox systems, formerly in use at Rocky Flats and many other plants, a decision was made to convert to a recirculating ''inert'' atmosphere. The inert atmosphere consists of nitrogen, supplied from an on-site generating plant, diluting oxygen content to one to 5 percent by volume. Problems encountered during the change over included: determination of all factors influencing air leakage into the system, and reducing leakage to the practical minimum; meeting all fire and safety standards on the filter plenum and exhaust systems; provision for converting portions of the system to an air atmosphere to conduct maintenance work; inclusion of oxygen analyzers throughout the system to check gas quality and monitor for leaks; and the use of automatic controls to protect against a variety of potential malfunctions. The current objectives to reduce fire hazards have been met and additional safeguards were added. The systems are operating satisfactorily. (U.S.)

Chromium concentrations in ruminant feed ingredients.

Science.gov (United States)

Spears, J W; Lloyd, K E; Krafka, K

2017-05-01

Chromium (Cr), in the form of Cr propionate, has been permitted for supplementation to cattle diets in the United States at levels up to 0.50 mg of Cr/kg of DM since 2009. Little is known regarding Cr concentrations naturally present in practical feed ingredients. The present study was conducted to determine Cr concentrations in feed ingredients commonly fed to ruminants. Feed ingredients were collected from dairy farms, feed mills, grain bins, and university research farms. Mean Cr concentrations in whole cereal grains ranged from 0.025 mg/kg of DM for oats to 0.041 mg/kg of DM for wheat. Grinding whole samples of corn, soybeans, and wheat through a stainless steel Wiley mill screen greatly increased analyzed Cr concentrations. Harvested forages had greater Cr concentrations than concentrates, and alfalfa hay or haylage had greater Cr concentrations than grass hay or corn silage. Chromium in alfalfa hay or haylage (n = 13) averaged 0.522 mg/kg of DM, with a range of 0.199 to 0.889 mg/kg of DM. Corn silage (n = 21) averaged 0.220 mg of Cr/kg of DM with a range of 0.105 to 0.441 mg of Cr/kg of DM. By-product feeds ranged from 0.040 mg of Cr/kg of DM for cottonseed hulls to 1.222 mg of Cr/kg of DM for beet pulp. Of the feed ingredients analyzed, feed grade phosphate sources had the greatest Cr concentration (135.0 mg/kg). Most ruminant feedstuffs and feed ingredients had less than 0.50 mg of Cr/kg of DM. Much of the analyzed total Cr in feed ingredients appears to be due to Cr contamination from soil or metal contact during harvesting, processing, or both. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Allergenic Ingredients in Personal Hygiene Wet Wipes.

Science.gov (United States)

Aschenbeck, Kelly A; Warshaw, Erin M

Wet wipes are a significant allergen source for anogenital allergic contact dermatitis. The aim of the study was to calculate the frequency of potentially allergenic ingredients in personal hygiene wet wipes. Ingredient lists from brand name and generic personal hygiene wet wipes from 4 large retailers were compiled. In the 54 personal hygiene wet wipes evaluated, a total of 132 ingredients were identified (average of 11.9 ingredients per wipe). The most common ingredients were Aloe barbadensis (77.8%), citric acid (77.8%), fragrance (72.2%), sorbic acid derivatives (63.0%), tocopherol derivatives (63.0%), glycerin (59.3%), phenoxyethanol (55.6%), disodium cocoamphodiacetate (53.7%), disodium ethylenediaminetetraacetic acid (EDTA) (42.6%), propylene glycol (42.6%), iodopropynyl butylcarbamate (40.7%), chamomile extracts (38.9%), sodium benzoate (35.2%), bronopol (22.2%), sodium citrate (22.2%), lanolin derivatives (20.4%), parabens (20.4%), polyethylene glycol derivatives (18.5%), disodium phosphate (16.7%), dimethylol dimethyl hydantoin (DMDM) (14.8%), and cocamidopropyl propylene glycol (PG)-dimonium chloride phosphate (11.1%). Of note, methylisothiazolinone (5.6%) was uncommon; methylchloroisothiazolinone was not identified in the personal hygiene wet wipes examined. There are many potential allergens in personal hygiene wet wipes, especially fragrance and preservatives.

HIM-herbal ingredients in-vivo metabolism database.

Science.gov (United States)

Kang, Hong; Tang, Kailin; Liu, Qi; Sun, Yi; Huang, Qi; Zhu, Ruixin; Gao, Jun; Zhang, Duanfeng; Huang, Chenggang; Cao, Zhiwei

2013-05-31

Herbal medicine has long been viewed as a valuable asset for potential new drug discovery and herbal ingredients' metabolites, especially the in vivo metabolites were often found to gain better pharmacological, pharmacokinetic and even better safety profiles compared to their parent compounds. However, these herbal metabolite information is still scattered and waiting to be collected. HIM database manually collected so far the most comprehensive available in-vivo metabolism information for herbal active ingredients, as well as their corresponding bioactivity, organs and/or tissues distribution, toxicity, ADME and the clinical research profile. Currently HIM contains 361 ingredients and 1104 corresponding in-vivo metabolites from 673 reputable herbs. Tools of structural similarity, substructure search and Lipinski's Rule of Five are also provided. Various links were made to PubChem, PubMed, TCM-ID (Traditional Chinese Medicine Information database) and HIT (Herbal ingredients' targets databases). A curated database HIM is set up for the in vivo metabolites information of the active ingredients for Chinese herbs, together with their corresponding bioactivity, toxicity and ADME profile. HIM is freely accessible to academic researchers at http://www.bioinformatics.org.cn/.

Experimental investigations of the minimum ignition energy and the minimum ignition temperature of inert and combustible dust cloud mixtures

Energy Technology Data Exchange (ETDEWEB)

Addai, Emmanuel Kwasi, E-mail: emmanueladdai41@yahoo.com; Gabel, Dieter; Krause, Ulrich

2016-04-15

Highlights: • Ignition sensitivity of a highly flammable dust decreases upon addition of inert dust. • Minimum ignition temperature of a highly flammable dust increases when inert concentration increase. • Minimum ignition energy of a highly flammable dust increases when inert concentration increase. • The permissible range for the inert mixture to minimize the ignition risk lies between 60 to 80%. - Abstract: The risks associated with dust explosions still exist in industries that either process or handle combustible dust. This explosion risk could be prevented or mitigated by applying the principle of inherent safety (moderation). This is achieved by adding an inert material to a highly combustible material in order to decrease the ignition sensitivity of the combustible dust. The presented paper deals with the experimental investigation of the influence of adding an inert dust on the minimum ignition energy and the minimum ignition temperature of the combustible/inert dust mixtures. The experimental investigation was done in two laboratory scale equipment: the Hartmann apparatus and the Godbert-Greenwald furnace for the minimum ignition energy and the minimum ignition temperature test respectively. This was achieved by mixing various amounts of three inert materials (magnesium oxide, ammonium sulphate and sand) and six combustible dusts (brown coal, lycopodium, toner, niacin, corn starch and high density polyethylene). Generally, increasing the inert materials concentration increases the minimum ignition energy as well as the minimum ignition temperatures until a threshold is reached where no ignition was obtained. The permissible range for the inert mixture to minimize the ignition risk lies between 60 to 80%.

Experimental investigations of the minimum ignition energy and the minimum ignition temperature of inert and combustible dust cloud mixtures

International Nuclear Information System (INIS)

Addai, Emmanuel Kwasi; Gabel, Dieter; Krause, Ulrich

2016-01-01

Highlights: • Ignition sensitivity of a highly flammable dust decreases upon addition of inert dust. • Minimum ignition temperature of a highly flammable dust increases when inert concentration increase. • Minimum ignition energy of a highly flammable dust increases when inert concentration increase. • The permissible range for the inert mixture to minimize the ignition risk lies between 60 to 80%. - Abstract: The risks associated with dust explosions still exist in industries that either process or handle combustible dust. This explosion risk could be prevented or mitigated by applying the principle of inherent safety (moderation). This is achieved by adding an inert material to a highly combustible material in order to decrease the ignition sensitivity of the combustible dust. The presented paper deals with the experimental investigation of the influence of adding an inert dust on the minimum ignition energy and the minimum ignition temperature of the combustible/inert dust mixtures. The experimental investigation was done in two laboratory scale equipment: the Hartmann apparatus and the Godbert-Greenwald furnace for the minimum ignition energy and the minimum ignition temperature test respectively. This was achieved by mixing various amounts of three inert materials (magnesium oxide, ammonium sulphate and sand) and six combustible dusts (brown coal, lycopodium, toner, niacin, corn starch and high density polyethylene). Generally, increasing the inert materials concentration increases the minimum ignition energy as well as the minimum ignition temperatures until a threshold is reached where no ignition was obtained. The permissible range for the inert mixture to minimize the ignition risk lies between 60 to 80%.

Inert anode containing base metal and noble metal useful for the electrolytic production of aluminum

Science.gov (United States)

Ray, Siba P.; Liu, Xinghua

2000-01-01

An inert anode for production of metals such as aluminum is disclosed. The inert anode comprises a base metal selected from Cu and Ag, and at least one noble metal selected from Ag, Pd, Pt, Au, Rh, Ru, Ir and Os. The inert anode may optionally be formed of sintered particles having interior portions containing more base metal than noble metal and exterior portions containing more noble metal than base metal. In a preferred embodiment, the base metal comprises Cu, and the noble metal comprises Ag, Pd or a combination thereof.

Fabrication of inert matrices for heterogeneous transmutation. EFTTRA-T2 (RAS 2) irradiation programme

International Nuclear Information System (INIS)

Boshoven, J.G.; Hein, H.; Konings, R.J.M.

1996-07-01

This report describes the fabrication of targets containing inert matrices for the heterogeneous transmutation of plutonium and minor actinides. These targets will be irradiated in the EFTTRA-T2 (RAS-2) irradiation programme. The selection, preparation and characterization of the inert matrices and fabrication and loading of the irradiation capsules are discussed. (orig.)

Electrostatic separation for functional food ingredient production

NARCIS (Netherlands)

Wang, J.

2016-01-01

Summary

Dry fractionation is a promising alternative to wet extraction processes for production of food ingredients, since it uses hardly any water, consumes less energy and retains the native functionality of the ingredients. It combines milling and dry separation to

Mixed PWR core loadings with inert matrix Pu-fuel assemblies

International Nuclear Information System (INIS)

Stanculescu, A.; Kasemeyer, U.; Paratte, J.-M.; Chawla, R.

1999-01-01

The most efficient way to enhance plutonium consumption in light water reactors is to eliminate the production of plutonium all together. This requirement leads to fuel concepts in which the uranium is replaced by an inert matrix. At PSI, studies have focused on employing ZrO 2 as inert matrix. Adding a burnable poison to such a fuel proves to be necessary. As a result of scoping studies, Er 2 O 3 was identified as the most suitable burnable poison material. The results of whole-core three-dimensional neutronics analyses indicated, for a present-day 1000 MW e pressurised water reactor, the feasibility of an asymptotic equilibrium four-batch cycle fuelled solely with the proposed PuO 2 -Er 2 O 3 -ZrO 2 inert matrix fuel (IMF). The present paper presents the results of more recent investigations related to 'real-life' situations, which call for transition configurations in which mixed IMF and UO 2 assembly loadings must be considered. To determine the influence of the introduction of IMF assemblies on the characteristics of a UO 2 -fuelled core, three-dimensional full-core calculations have been performed for a present-day 1000 MW e PWR containing up to 12 optimised IMF assemblies. (author)

A steam inerting system for hydrogen disposal for the Vandenberg Shuttle

Science.gov (United States)

Belknap, Stuart B.

1988-01-01

A two-year feasibility and test program to solve the problem of unburned confined hydrogen at the Vandenberg Space Launch Complex Six (SLC-6) during Space Shuttle Main Engine (SSME) firings is discussed. A novel steam inerting design was selected for development. Available sound suppression water is superheated to flash to steam at the duct entrance. Testing, analysis, and design during 1987 showed that the steam inerting system (SIS) solves the problem and meets other flight-critical system requirements. The SIS design is complete and available for installation at SLC-6 to support shuttle or derivative vehicles.

Status of the inert matrix fuel program at PSI

International Nuclear Information System (INIS)

Ledergerber, G.; Degueldre, C.; Kasemeyer, U.; Stanculescu, A.; Paratte, J.M.; Chawla, R.

1997-01-01

Incineration of plutonium by a once-through cycle in LWRs utilising an inert matrix based fuel may prove to be an attractive way of making use of the energy of fissile plutonium and reducing both the hazard potential and the volumes of the waste. Yttria stabilised zirconia forms a solid solution with oxides of rare earth elements (e.g. erbium, cerium) and some actinides. The small absorption cross section, the excellent stability under irradiation, and the insolubility in acids and water recommends this material as an inert matrix. Neutronics calculations with erbium as burnable poison show that these compositions would be optimal from the reactivity point of view. A fuel element with an improved reactivity behaviour over its life cycle has been designed for possible introduction into a heterogeneous LWR core. (author). 16 refs., 1 tab., 10 figs

For cermet inert anode containing oxide and metal phases useful for the electrolytic production of metals

Science.gov (United States)

Ray, Siba P.; Liu, Xinghua; Weirauch, Douglas A.

2002-01-01

A cermet inert anode for the electrolytic production of metals such as aluminum is disclosed. The inert anode comprises a ceramic phase including an oxide of Ni, Fe and M, where M is at least one metal selected from Zn, Co, Al, Li, Cu, Ti, V, Cr, Zr, Nb, Ta, W, Mo, Hf and rare earths, preferably Zn and/or Co. Preferred ceramic compositions comprise Fe.sub.2 O.sub.3, NiO and ZnO or CoO. The cermet inert anode also comprises a metal phase such as Cu, Ag, Pd, Pt, Au, Rh, Ru, Ir and/or Os. A preferred metal phase comprises Cu and Ag. The cermet inert anodes may be used in electrolytic reduction cells for the production of commercial purity aluminum as well as other metals.

Types of Pesticide Ingredients

Science.gov (United States)

Pesticide active ingredients are described by the types of pests they control or how they work. For example, algicides kill algae, biopesticides are derived from natural materials, and insecticides kill insects.

An inert 3D emulsification device for individual precipitation and concentration of amorphous drug nanoparticles.

Science.gov (United States)

Lorenz, T; Bojko, S; Bunjes, H; Dietzel, A

2018-02-13

Nanosizing increases the specific surface of drug particles, leading to faster dissolution inside the organism and improving the bioavailability of poorly water-soluble drugs. A novel approach for the preparation of drug nanoparticles in water using chemically inert microfluidic emulsification devices is presented in this paper. A lithographic fabrication sequence was established, allowing fabrication of intersecting and coaxial channels of different depths in glass as is required for 3D flow-focusing. Fenofibrate was used as a model for active pharmaceutical ingredients with very low water solubility in the experiments. It was dissolved in ethyl acetate and emulsified in water, as allowed by the 3D flow-focusing geometry. In the thread formation regime, the drug solution turned into monodisperse droplets of sizes down to below 1 μm. Fast supersaturation occurs individually in each droplet, as the disperse phase solvent progressively diffuses into the surrounding water. Liquid antisolvent precipitation results in highly monodisperse and amorphous nanoparticles of sizes down to 128 nm which can be precisely controlled by the continuous and disperse phase pressure. By comparing optically measured droplet sizes with particle sizes by dynamic light scattering, we could confirm that exactly one particle forms in every droplet. Furthermore, a downstream on-chip concentration allowed withdrawal of major volumes of only the continuous phase fluid which enabled an increase of particle concentration by up to 250 times.

Viability of inert matrix fuel in reducing plutonium amounts in reactors

International Nuclear Information System (INIS)

2006-08-01

Reactors worldwide have produced more than 2000 tonnes of plutonium, contained in spent fuel or as separated forms through reprocessing. Disposition of fissile materials has become a primary concern of nuclear non-proliferation efforts. There is a significant interest in IAEA Member States to develop proliferation resistant nuclear fuel cycles for incineration of plutonium such as inert matrix fuels (IMFs). The present report summarises R and D work on inert matrix fuel for plutonium and (to a lesser extent) minor actinide stock-pile reduction, and discusses the possible strategies to include inert matrix fuel approaches to the nuclear fuel cycle. The publication reviews the status of potential IMF candidates and describes several identified candidate materials for both fast and thermal reactors: MgO, ZrO2, SiC, Zr alloy, SiAl, ZrN; some of these have undergone test irradiations and post-irradiation examination. Also discussed are modelling of IMF fuel performance and safety analysis. System studies have identified strategies for both implementation of IMF fuel as homogeneous or heterogeneous phases, as assemblies or core loadings and in existing reactors in the shorter term, as well as in new reactors in the longer term

21 CFR 340.10 - Stimulant active ingredient.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Stimulant active ingredient. 340.10 Section 340.10 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS FOR HUMAN USE STIMULANT DRUG PRODUCTS FOR OVER-THE-COUNTER HUMAN USE Active Ingredient § 340.10...

Inert gas handling in ion plating systems

International Nuclear Information System (INIS)

Goode, A.R.; Burden, M.St.J.

1979-01-01

The results of an investigation into the best methods for production and monitoring of the inert gas environment for ion plating systems are reported. Work carried out on Pirani gauges and high pressure ion gauges for the measurement of pressures in the ion plating region (1 - 50mtorr) and the use of furnaces for cleaning argon is outlined. A schematic of a gas handling system is shown and discussed. (UK)

Relationships among ventilation-perfusion distribution, multiple inert gas methodology and metabolic blood-gas tensions.

Science.gov (United States)

Lee, A S; Patterson, R W; Kaufman, R D

1987-12-01

The retention equations upon which the Multiple Inert Gas Method is based are derived from basic principles using elementary algebra. It is shown that widely disparate distributions produce indistinguishable sets of retentions. The limits of resolution of perfused compartments in the VA/Q distribution obtainable by the use of the multiple inert gas method are explored mathematically, and determined to be at most shunt and two alveolar compartments ("tripartite" distribution). Every continuous distribution studied produced retentions indistinguishable from those of its unique "matching" tripartite distribution. When a distribution is minimally specified, it is unique. Any additional specification (increased resolution--more compartments) of the distribution results in the existence of an infinitude of possible distributions characterized by indistinguishable sets of retention values. No further increase in resolution results from the use of more tracers. When sets of retention values were extracted from published multiple inert gas method continuous distributions, and compared with the published "measured" retention sets, substantial differences were found. This illustrates the potential errors incurred in the practical, in vivo application of the multiple inert gas method. In preliminary studies, the tripartite distribution could be determined with at least comparable accuracy by blood-gas (oxygen, carbon dioxide) measurements.

Dietary Supplement Ingredient Database

Science.gov (United States)

... and US Department of Agriculture Dietary Supplement Ingredient Database Toggle navigation Menu Home About DSID Mission Current ... values can be saved to build a small database or add to an existing database for national, ...

ENRICHMENT OF POULTRY PRODUCTS WITH FUNCTIONAL INGREDIENTS

Directory of Open Access Journals (Sweden)

Gordana Kralik

2012-06-01

Full Text Available Primary role of food is to provide nutritive stuffs in sufficient amounts to meet nutritive requirements. However, recent scientific findings confirm assumptions that particular food or its ingredients had positive physiological and psychological effects on health. Functional food is referred to food rich in ingredients, having beneficial effects on one or more functions in an organism. By consuming functional food consumers can expect some health benefits. Production of poultry products as functional food is getting more important on foreign markets while portion of such products on domestic food market is insignificant. The aim of this paper is to present possibilities for enrichment of poultry products, such as broiler and turkey meat and chicken eggs, as they can be characterized as functional food. Functional ingredients in poultry products are polyunsaturated fatty acids (LNA, EPA and DHA and antioxidants. Enrichment of poultry products with the stated ingredients that are beneficial for human health is subject of many researches, and only recently have researches been directed towards assessment of market sustainability of such products.

Gamma-Ray Pulsars: Beaming Evolution, Statistics, and Unidentified EGRET Sources

Science.gov (United States)

Yadigaroglu, I.-A.; Romani, Roger W.

1995-08-01

We compute the variation of the beaming fraction with the efficiency of high-energy γ-ray production in the outer gap pulsar model of Romani and Yadigaroglu. This allows us to correct the fluxes observed for pulsars in the EGRET band and to derive a simple estimate of the variation of efficiency with age. Integration of this model over the population of young neutron stars gives the expected number of γ-ray pulsars along with their distributions in age and distance. This model also shows that many of the unidentified EGRET plane sources should be pulsars and predicts the γ-ray fluxes of known radio pulsars. The contribution of unresolved pulsars to the background flux in the EGRET band is found to be ˜5%.

Mechanical behaviour and diffusion of gas during neutron irradiation of actinides in ceramic inert matrices

NARCIS (Netherlands)

Neeft, E.A.C.

2004-01-01

Fission of actinides from nuclear waste in inert matrices (materials without uranium) can reduce the period in time that nuclear waste is more radiotoxic than uranium ore that is the rock from which ordinary reactor fuel is made. A pioneering study is performed with the inert matrices: MgO, MgAl2O4,

A scintillation detector for measuring inert gas beta rays

International Nuclear Information System (INIS)

Shi Hengchang; Yu Yunchang

1989-10-01

The inert gas beta ray scintillation detector, which is made of organic high polymers as the base and coated with compact fluorescence materials, is a lower energy scintillation detector. It can be used in the nuclear power plant and radioactive fields as a lower energy monitor to detect inert gas beta rays. Under the conditions of time constant 10 minutes, confidence level is 99.7% (3σ), the intensity of gamma rays 2.6 x 10 -7 C/kg ( 60 Co), and the minimum detectable concentration (MDC) of this detector for 133 Xe 1.2 Bq/L. The measuring range for 133 Xe is 11.1 ∼ 3.7 x 10 4 Bq/L. After a special measure is taken, the device is able to withstand 3 x 10 5 Pa gauge pressure. In the loss-of-cooolant-accident, it can prevent the radioactive gas of the detector from leaking. This detector is easier to be manufactured and decontaminated

Finding X-ray counterparts for unidentified sources in the 105 months BAT survey - 1

Science.gov (United States)

Stephen, J. B.; Bassani, L.; Malizia, A.; Masetti, N.; Ubertini, P.

2018-02-01

We provide X-ray counterparts for the unidentified Swift/BAT sources listed in the 105 month catalogue (Oh et al. 2018, ApJS in press). These associations were found by cross-correlating the list of U1,U2 and U3 sources with the ROSAT Bright (RASSBSC, Voges et al. 1999, A & A, 349, 389) and the XMM-Newton Slew (XMMSlew, Saxton et al. 2008, A & A, 480, 611) catalogues.

Nano-microdelivery systems for oral delivery of an active ingredient

DEFF Research Database (Denmark)

2014-01-01

A composition for oral delivery of one or more active ingredients in the form of a lipid nano-micro-delivery system comprising a lipid nano-micro-structure comprising at least one lipid and at least one active ingredient, said at least one active ingredient being immobilized in said lipid nano...

Post-inertization of large dry containments in case of beyond-design base events in PWR plants

International Nuclear Information System (INIS)

Tiltmann, M.; Risse, D.; Pana, P.; Huettermann, B.; Rohde, J.

1993-12-01

The objective is to present a summary of basic thoughts and concepts as described in various publications. The report points out the obvious advantages and disadvantages of individual strategies as wel as the requirements derived from the knowledge of possible accident sequences for such a concept. Scoping calculations on the injection of inert-gas into the containment during the progress of accidents revealed additional indications as regards e.g. the required amount of inert-gas, the injection rate, and the resulting pressure behaviour in the containment. Thereby an assessment of the effectiveness as well as of the feasibility of such measures has become possible. From the large number of different initial conclusions, two major ones are singled out and presented: 1) In principle, the technical realisation of post-inerting is possible. Thus a deflagration of hydrogen in the containment can be prevented; 2) Post-inerting cannot be realised independent of the accident progress. Specific criteria for carrying out such measures will require extensive examinations. (orig./HP) [de

An investigation of the microstructures and properties of metal inert ...

Indian Academy of Sciences (India)

Friction stir welding; metal inert gas welding; aluminum alloy 5083; ... (2008) have studied fatigue crack propagation behaviour of friction ..... Kumar K, Kailas SV 2008 The role of friction stir welding tool on material flow and weld formation,.

Potential of Insect-Derived Ingredients for Food Applications

NARCIS (Netherlands)

Tzompa Sosa, D.A.; Fogliano, V.

2017-01-01

Insects are a sustainable and efficient protein and lipid source, compared with conventional livestock. Moreover, insect proteins and lipids are highly nutritional. Therefore, insect proteins and lipids can find its place as food ingredients. The use of insect proteins and lipids as food ingredients

Trapping of He clusters by inert-gas impurities in tungsten: First-principles predictions and experimental validation

Energy Technology Data Exchange (ETDEWEB)

Nguyen-Manh, Duc, E-mail: duc.nguyen@ccfe.ac.uk; Dudarev, S.L.

2015-06-01

Properties of point defects resulting from the incorporation of inert-gas atoms in bcc tungsten are investigated systematically using first-principles density functional theory (DFT) calculations. The most stable configuration for the interstitial neon, argon, krypton and xenon atoms is the tetrahedral site, similarly to what was found earlier for helium in W. The calculated formation energies for single inert-gas atoms at interstitial sites as well as at substitutional sites are much larger for Ne, Ar, Kr and Xe than for He. While the variation of the energy of insertion of inert-gas defects into interstitial configurations can be explained by a strong effect of their large atomic size, the trend exhibited by their substitutional energies is more likely related to the covalent interaction between the noble gas impurity atoms and the tungsten atoms. There is a remarkable variation exhibited by the energy of interaction between inert-gas impurities and vacancies, where a pronounced size effect is observed when going from He to Ne, Ar, Kr, Xe. The origin of this trend is explained by electronic structure calculations showing that p-orbitals play an important part in the formation of chemical bonds between a vacancy and an atom of any of the four inert-gas elements in comparison with helium, where the latter contains only 1s{sup 2} electrons in the outer shell. The binding energies of a helium atom trapped by five different defects (He-v, Ne-v, Ar-v, Kr-v, Xe-v, where v denotes a vacancy in bcc-W) are all in excellent agreement with experimental data derived from thermal desorption spectroscopy. Attachment of He clusters to inert gas impurity atom traps in tungsten is analysed as a function of the number of successive trapping helium atoms. Variation of the Young modulus due to inert-gas impurities is analysed on the basis of data derived from DFT calculations.

Structured adsorbents for isolation of functional food ingredients

NARCIS (Netherlands)

Rodriguez Illera, M.

2014-01-01

Separation and purification of functional ingredients from raw or waste streams are often done via processes that include a chromatographic step using a packed bed of resin particles that have affinity for the ingredients to be separated. A column packed with these particles presents numerous

Method of making composition suitable for use as inert electrode having good electrical conductivity and mechanical properties

Science.gov (United States)

Ray, S.P.; Rapp, R.A.

1986-04-22

An improved inert electrode composition is suitable for use as an inert electrode in the production of metals such as aluminum by the electrolytic reduction of metal oxide or metal salt dissolved in a molten salt bath. The composition comprises one or more metals or metal alloys and metal compounds which may include oxides of the metals comprising the alloy. The alloy and metal compounds are interwoven in a network which provides improved electrical conductivity and mechanical strength while preserving the level of chemical inertness necessary for such an electrode to function satisfactorily. 8 figs.

Plutonium fuel lattice neutron behavior in inert matrix

International Nuclear Information System (INIS)

Hernandez L, H.; Lucatero, M. A.

2010-10-01

In several countries is had been researching the possibility of using plutonium, as weapon degree as reactor degree, as fuel material in commercial reactors to generate electricity. In special a great development has been in Pressure Water Reactors. However, in Mexico the reactors are Boiling Water Reactors type, reason for which the necessity to considers feasibility to use this fuel type in the reactors of nuclear power plant of Laguna Verde. For this propose a comparison of fuel lattice that compose a fuel assembly is made. The fuel assembly will propose to be used whit in the reactor present different inert matrix, as well as burnable poison. The material that compose the inert matrices used are cerium and zirconia (CeO 2 and ZrO 2 ) and as burnable poisons have gadolinium and erbium (Gd 2 O 4 and ErO 2 ). As far as the hydraulic design used is a cell 10 X 10 with two water channels. The lattice calculations are made with the Helios code a library with 35 energy groups, having determined the pin power factors, the infinite multiplication factor and the neutron flux profiles. (Author)

effects of metal inert gas welding parameters on some mechanical ...

African Journals Online (AJOL)

EFFECTS OF METAL INERT GAS WELDING PARAMETERS ON SOME MECHANICAL PROPERTIES OF AUSTENITIC STAINLESS STEEL IN ACIDIC ... Design Expert Software, Scanning Electron Microscopy (SEM), Rockwell Hardness Test, Monsanto Tensometer and Izod Impact Test were used to determine the ...

Finding X-ray counterparts for unidentified sources in the 105 months BAT survey - 2

Science.gov (United States)

Stephen, J. B.; Bassani, L.; Malizia, A.; Masetti, N.; Ubertini, P.

2018-02-01

We provide X-ray counterparts for unidentified Swift/BAT sources in the 105 month catalogue (Oh et al. 2018, ApJS in press). They were found by cross-correlating the list of U1,U2 and U3 sources with the ROSAT Bright (RASSBSC, Voges et al. 1999, A & A, 349, 389) and XMM-Newton Slew (XMMSlew, Saxton et al. 2008, A & A, 480, 611) catalogues and optically identified as reported in Atel #11340.

Distribution of inert gases in fines from the Cayley-Descartes region

Science.gov (United States)

Walton, J. R.; Lakatos, S.; Heymann, D.

1973-01-01

The inert gases in 14 different fines and in one sample of 2 to 4 mm fines from Apollo 16 were measured by mass spectroscopy with respect to trapped solar wind gases, cosmogenic gases, and 'parentless' Ar-40. Such studies are helpful for the understanding of regolith evolution, of transport of regolith fines, and of the lunar atmosphere. The Apollo 16 soils are unique because they represent, after Luna 20, the second and much more extensive record from the lunar highlands. The landing site presents the problem of materials from the Cayley Formation vs those from the Descartes Formation. There are two large, relatively fresh craters in the area, North Ray and South Ray, whose ejecta patterns may be recognized in the inert-gas record.

Functional ingredients from microalgae

NARCIS (Netherlands)

Buono, S.; Langellotti, A.L.; Martello, A.; Rinna, F.; Fogliano, V.

2014-01-01

A wide variety of natural sources are under investigation to evaluate their possible use for new functional ingredient formulation. Some records attested the traditional and ancient use of wild harvested microalgae as human food but their cultivation for different purposes started about 40 years

Innovative inert matrix-thoria fuels for in-reactor plutonium disposition

International Nuclear Information System (INIS)

Vettraino, F.; Padovani, E.; Luzzi, L.; Lombardi, C.; Thoresen, H.; Oberlander, B.; Iversen, G.; Espeland, M.

1999-01-01

The present leading option for plutonium disposition, either civilian or weapons Pu, is to burn it in LWRs after having converted it to MOX fuel. However, among the possible types of fuel which can be envisaged to burn plutonium in LWRs, innovative U-free fuels such as inert matrix and thoria fuel are novel concept in view of a more effective and ultimate solution from both security and safety standpoint. Inert matrix fuel is an non-fertile oxide fuel consisting of PuO 2 , either weapon-grade or reactor-grade, diluted in inert oxides such as for ex. stabilized ZrO 2 or MgAl 2 O 4 , its primary advantage consisting in no-production of new plutonium during irradiation, because it does not contain uranium (U-free fuel) whose U-238 isotope is the departure nuclide for breeding Pu-239. Some thoria addition in the matrix (thoria-doped fuel) may be required for coping with reactivity feedback needs. The full thoria-plutonia fuel though still a U-free variant cannot be defined non-fertile any more because the U-233 generation. The advantage of such a fuel option consisting basically on a remarkable already existing technological background and a potential acceleration in getting rid of the Pu stocks. All U-free fuels are envisaged to be operated under a once-through cycle scheme being the spent fuel outlooked to be sent directly to the final disposal in deep geological formations without requiring any further reprocessing treatment, thanks to the quality-poor residual Pu and a very high chemical stability under the current fuel reprocessing techniques. Besides, inert matrix-thoria fuel technology is suitable for in-reactor MAs transmutation. An additional interest in Th containing fuel refers to applicability in ADS, the innovative accelerated driven subcritical systems, specifically aimed at plutonium, minor actnides and long lived fission products transmutation in a Th-fuel cycle scheme which enables to avoid generations of new TRUs. A first common irradiation experiment

Innovative natural functional ingredients from microalgae.

Science.gov (United States)

Plaza, Merichel; Herrero, Miguel; Cifuentes, Alejandro; Ibáñez, Elena

2009-08-26

Nowadays, a wide variety of compounds such as polyphenols, polyunsaturated fatty acids (PUFA), or phytosterols obtained, for example, from wine, fish byproducts, or plants are employed to prepare new functional foods. However, unexplored natural sources of bioactive ingredients are gaining much attention since they can lead to the discovery of new compounds or bioactivities. Microalgae have been proposed as an interesting, almost unlimited, natural source in the search for novel natural functional ingredients, and several works have shown the possibility to find bioactive compounds in these organisms. Some advantages can be associated with the study of microalgae such as their huge diversity, the possibility of being used as natural reactors at controlled conditions, and their ability to produce active secondary metabolites to defend themselves from adverse or extreme conditions. In this contribution, an exhaustive revision is presented involving the research for innovative functional food ingredients from microalgae. The most interesting results in this promising field are discussed including new species composition and bioactivity and new processing and extraction methods. Moreover, the future research trends are critically commented.

Chromium liquid waste inertization in an inorganic alkali activated matrix: Leaching and NMR multinuclear approach

International Nuclear Information System (INIS)

Ponzoni, Chiara; Lancellotti, Isabella; Barbieri, Luisa; Spinella, Alberto; Saladino, Maria Luisa; Martino, Delia Chillura; Caponetti, Eugenio; Armetta, Francesco; Leonelli, Cristina

2015-01-01

Highlights: • Inertization of chromium liquid waste in aluminosilicate matrix. • Water less inertization technique exploiting the waste water content. • Liquid waste inertization without drying step. • Long term stabilization study through leaching test. • SEM analysis and 29 Si and 27 Al MAS NMR in relation with long curing time. - Abstract: A class of inorganic binders, also known as geopolymers, can be obtained by alkali activation of aluminosilicate powders at room temperature. The process is affected by many parameters (curing time, curing temperature, relative humidity etc.) and leads to a resistant matrix usable for inertization of hazardous waste. In this study an industrial liquid waste containing a high amount of chromium (≈2.3 wt%) in the form of metalorganic salts is inertized into a metakaolin based geopolymer matrix. One of the innovative aspects is the exploitation of the water contained in the waste for the geopolymerization process. This avoided any drying treatment, a common step in the management of liquid hazardous waste. The evolution of the process - from the precursor dissolution to the final geopolymer matrix hardening - of different geopolymers containing a waste amount ranging from 3 to 20% wt and their capability to inertize chromium cations were studied by: i) the leaching tests, according to the EN 12,457 regulation, at different curing times (15, 28, 90 and 540 days) monitoring releases of chromium ions (Cr(III) and Cr(VI)) and the cations constituting the aluminosilicate matrix (Na, Si, Al); ii) the humidity variation for different curing times (15 and 540 days); iii) SEM characterization at different curing times (28 and 540 days); iv) the trend of the solution conductivity and pH during the leaching test; v) the characterization of the short-range ordering in terms of T−O−T bonds (where T is Al or Si) by 29 Si and 27 Al solid state magic-angle spinning nuclear magnetic resonance (ss MAS NMR) for geopolymers

Chromium liquid waste inertization in an inorganic alkali activated matrix: Leaching and NMR multinuclear approach

Energy Technology Data Exchange (ETDEWEB)

Ponzoni, Chiara, E-mail: chiara.ponzoni@unimore.it [University of Modena and Reggio Emilia, Department of Engineering “Enzo Ferrari”, Modena (Italy); Lancellotti, Isabella; Barbieri, Luisa [University of Modena and Reggio Emilia, Department of Engineering “Enzo Ferrari”, Modena (Italy); Spinella, Alberto; Saladino, Maria Luisa [University of Palermo CGA-UniNetLab, Palermo (Italy); Martino, Delia Chillura [University of Palermo, Department STEBICEF, Palermo (Italy); Caponetti, Eugenio [University of Palermo CGA-UniNetLab, Palermo (Italy); University of Palermo, Department STEBICEF, Palermo (Italy); Armetta, Francesco [University of Palermo, Department STEBICEF, Palermo (Italy); Leonelli, Cristina [University of Modena and Reggio Emilia, Department of Engineering “Enzo Ferrari”, Modena (Italy)

2015-04-09

Highlights: • Inertization of chromium liquid waste in aluminosilicate matrix. • Water less inertization technique exploiting the waste water content. • Liquid waste inertization without drying step. • Long term stabilization study through leaching test. • SEM analysis and {sup 29}Si and {sup 27}Al MAS NMR in relation with long curing time. - Abstract: A class of inorganic binders, also known as geopolymers, can be obtained by alkali activation of aluminosilicate powders at room temperature. The process is affected by many parameters (curing time, curing temperature, relative humidity etc.) and leads to a resistant matrix usable for inertization of hazardous waste. In this study an industrial liquid waste containing a high amount of chromium (≈2.3 wt%) in the form of metalorganic salts is inertized into a metakaolin based geopolymer matrix. One of the innovative aspects is the exploitation of the water contained in the waste for the geopolymerization process. This avoided any drying treatment, a common step in the management of liquid hazardous waste. The evolution of the process - from the precursor dissolution to the final geopolymer matrix hardening - of different geopolymers containing a waste amount ranging from 3 to 20% wt and their capability to inertize chromium cations were studied by: i) the leaching tests, according to the EN 12,457 regulation, at different curing times (15, 28, 90 and 540 days) monitoring releases of chromium ions (Cr(III) and Cr(VI)) and the cations constituting the aluminosilicate matrix (Na, Si, Al); ii) the humidity variation for different curing times (15 and 540 days); iii) SEM characterization at different curing times (28 and 540 days); iv) the trend of the solution conductivity and pH during the leaching test; v) the characterization of the short-range ordering in terms of T−O−T bonds (where T is Al or Si) by {sup 29}Si and {sup 27}Al solid state magic-angle spinning nuclear magnetic resonance (ss MAS NMR) for

Methanol Droplet Combustion in Oxygen-Inert Environments in Microgravity

Science.gov (United States)

Nayagam, Vedha; Dietrich, Daniel L.; Hicks, Michael C.; Williams, Forman A.

2013-01-01

The Flame Extinguishment (FLEX) experiment that is currently underway in the Combustion Integrated Rack facility onboard the International Space Station is aimed at understanding the effects of inert diluents on the flammability of condensed phase fuels. To this end, droplets of various fuels, including alkanes and alcohols, are burned in a quiescent microgravity environment with varying amounts of oxygen and inert diluents to determine the limiting oxygen index (LOI) for these fuels. In this study we report experimental observations of methanol droplets burning in oxygen-nitrogen-carbon dioxide and oxygen-nitrogen-helium gas mixtures at 0.7 and 1 atmospheric pressures. The initial droplet size varied between approximately 1.5 mm and 4 mm to capture both diffusive extinction brought about by insufficient residence time at the flame and radiative extinction caused by excessive heat loss from the flame zone. The ambient oxygen concentration varied from a high value of 30% by volume to as low as 12%, approaching the limiting oxygen index for the fuel. The inert dilution by carbon dioxide and helium varied over a range of 0% to 70% by volume. In these experiments, both freely floated and tethered droplets were ignited using symmetrically opposed hot-wire igniters and the burning histories were recorded onboard using digital cameras, downlinked later to the ground for analysis. The digital images yielded droplet and flame diameters as functions of time and subsequently droplet burning rate, flame standoff ratio, and initial and extinction droplet diameters. Simplified theoretical models correlate the measured burning rate constant and the flame standoff ratio reasonably well. An activation energy asymptotic theory accounting for time-dependent water dissolution or evaporation from the droplet is shown to predict the measured diffusive extinction conditions well. The experiments also show that the limiting oxygen index for methanol in these diluent gases is around 12% to

Experimental investigations of the minimum ignition energy and the minimum ignition temperature of inert and combustible dust cloud mixtures.

Science.gov (United States)

Addai, Emmanuel Kwasi; Gabel, Dieter; Krause, Ulrich

2016-04-15

The risks associated with dust explosions still exist in industries that either process or handle combustible dust. This explosion risk could be prevented or mitigated by applying the principle of inherent safety (moderation). This is achieved by adding an inert material to a highly combustible material in order to decrease the ignition sensitivity of the combustible dust. The presented paper deals with the experimental investigation of the influence of adding an inert dust on the minimum ignition energy and the minimum ignition temperature of the combustible/inert dust mixtures. The experimental investigation was done in two laboratory scale equipment: the Hartmann apparatus and the Godbert-Greenwald furnace for the minimum ignition energy and the minimum ignition temperature test respectively. This was achieved by mixing various amounts of three inert materials (magnesium oxide, ammonium sulphate and sand) and six combustible dusts (brown coal, lycopodium, toner, niacin, corn starch and high density polyethylene). Generally, increasing the inert materials concentration increases the minimum ignition energy as well as the minimum ignition temperatures until a threshold is reached where no ignition was obtained. The permissible range for the inert mixture to minimize the ignition risk lies between 60 to 80%. Copyright © 2016 Elsevier B.V. All rights reserved.

21 CFR 346.10 - Local anesthetic active ingredients.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Local anesthetic active ingredients. 346.10 Section 346.10 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... ingredient: (a) Benzocaine 5 to 20 percent. (b) Benzyl alcohol 1 to 4 percent. (c) Dibucaine 0.25 to 1...

Ingredient classification according to the digestible amino acid profile: an exploratory analysis

Directory of Open Access Journals (Sweden)

DE Faria Filho

2005-09-01

Full Text Available This study aimed: 1 to classify ingredients according to the digestible amino acid (AA profile; 2 to determine ingredients with AA profile closer to the ideal for broiler chickens; and 3 to compare digestible AA profiles from simulated diets with the ideal protein profile. The digestible AA levels of 30 ingredients were compiled from the literature and presented as percentages of lysine according to the ideal protein concept. Cluster and principal component analyses (exploratory analyses were used to compose and describe groups of ingredients according to AA profiles. Four ingredient groups were identified by cluster analysis, and the classification of the ingredients within each of these groups was obtained from a principal component analysis, showing 11 classes of ingredients with similar digestible AA profiles. The ingredients with AA profiles closer to the ideal protein were meat and bone meal 45, fish meal 60 and wheat germ meal, all of them constituting Class 1; the ingredients from the other classes gradually diverged from the ideal protein. Soybean meal, which is the main protein source for poultry, showed good AA balance since it was included in Class 3. On the contrary, corn, which is the main energy source in poultry diets, was classified in Class 8. Dietary AA profiles were improved when corn and/or soybean meal were partially or totally replaced in the simulations by ingredients with better AA balance.

Fuel hydrogen retention of tungsten and the reduction by inert gas glow discharges

Energy Technology Data Exchange (ETDEWEB)

Hino, T., E-mail: tomhino@qe.eng.hokudai.ac.jp [Laboratory of Plasma Physics and Engineering, Hokkaido University, Sapporo 060-8628 (Japan); Yamauchi, Y.; Kimura, Y. [Laboratory of Plasma Physics and Engineering, Hokkaido University, Sapporo 060-8628 (Japan); Nishimura, K. [National Institute for Fusion Science, Toki-shi, Gifu-ken 509-5292 (Japan); Ueda, Y. [Graduate School of Engineering, Osaka University, Suita-shi 565-0872 (Japan)

2012-08-15

Highlights: Black-Right-Pointing-Pointer The performances of inert gas glow discharges for reduction of fuel hydrogen retention in tungsten were systematically investigated. Black-Right-Pointing-Pointer For the tungsten with rough surface structure, the reduction of fuel hydrogen retention by inert gas discharges is quite small. Black-Right-Pointing-Pointer The deuterium glow discharge is quite useful to reduce the tritium retention in plasma facing walls in fusion reactor. Black-Right-Pointing-Pointer The wall baking with temperature higher than 700-800 K is also useful to reduce the tritium retention in plasma facing walls. - Abstract: Polycrystalline tungsten was exposed to deuterium glow discharge followed by He, Ne or Ar glow discharge. The amount of retained deuterium in the tungsten was measured using residual gas analysis. The amount of desorbed deuterium during the inert gas glow discharge was also measured. The amount of retained deuterium was 2-3 times larger compared with a case of stainless steel. The ratios of desorbed amount of deuterium by He, Ne and Ar glow discharges were 4.6, 3.1 and 2.9%, respectively. These values were one order of magnitude smaller compared with the case of stainless steel. The inert gas glow discharge is not suitable to reduce the fuel hydrogen retention for tungsten walls. However, the wall baking with a temperature higher than 700 K is suitable to reduce the fuel hydrogen retention. It is also shown that the use of deuterium glow discharge is effective to reduce the in-vessel tritium inventory in fusion reactors through the hydrogen isotope exchange.

Technical basis for storage of Zircaloy-clad spent fuel in inert gases

International Nuclear Information System (INIS)

Johnson, A.B. Jr.; Gilbert, E.R.

1983-09-01

The technical bases to establish safe conditions for dry storage of Zircaloy-clad fuel are summarized. Dry storage of fuel with zirconium alloy cladding has been licensed in Canada, the Federal Republic of Germany, and Switzerland. Dry storage demonstrations, hot cell tests, and modeling have been conducted using Zircaloy-clad fuel. The demonstrations have included irradiated boiling water reactor, pressurized heavy-water reactor, and pressurized water reactor fuel assemblies. Irradiated fuel has been emplaced in and retrieved from metal casks, dry wells, silos, and a vault. Dry storage tests and demonstrations have involved about 15,000 fuel rods, and about 5600 rods have been monitored during dry storage in inert gases with maximum cladding temperatures ranging from 50 to 570 0 C. Although some tests and demonstrations are still in progress, there is currently no evidence that any rods exposed to inert gases have failed (one PWR rod exposed to an air cover gas failed at about 270 0 C). Based on this favorable experience, it is concluded that there is sufficient information on fuel rod behavior, storage conditions, and potential cladding failure mechanisms to support licensing of dry storage in the US. This licensing position includes a requirement for inert cover gases and a maximum cladding temperature guideline of 380 0 C for Zircaloy-clad fuel. Using an inert cover gas assures that even if fuel with cladding defects were placed in dry storage, or if defects develop during storage, the defects would not propagate. Tests and demonstrations involving Zircaloy-clad rods and assemblies with maximum cladding temperatures above 400 0 C are in progress. When the results from these tests have been evaluated, the viability of higher temperature limits should be examined. Acceptable conditions for storage in air and dry storage of consolidated fuel are issues yet to be resolved

Measurements of hydrogen concentration in liquid sodium by using an inert gas carrier method

International Nuclear Information System (INIS)

Funada, T.; Nihei, I.; Yuhara, S.; Nakasuji, T.

1979-01-01

A technique was developed to measure the hydrogen level in liquid sodium using an inert gas carrier method. Hydrogen was extracted into an inert gas from sodium through a thin nickel membrane in the form of a helically wound tube. The amount of hydrogen in the inert gas was analyzed by gas chromatography. The present method is unique in that it can be used over the wide range of sodium temperatures (150 to 700 0 C) and has no problems associated with vacuum systems. The partial pressure of hydrogen in sodium was determined as a function of cold-trap temperature (T/sub c/). Sieverts' constant (K/sub s/) was determined as a function of sodium temperature (T). From Sieverts' constant, the solubility of hydrogen in sodium is calculated. It was found that other impurities in sodium, such as (O) and (OH), have little effect on the hydrogen pressure in the sodium loop

Comparison of three inert markers in measuring apparent nutrient digestibility of juvenile abalone under different culture condition and temperature regimes

Science.gov (United States)

Nur, K. U.; Adams, L.; Stone, D.; Savva, N.; Adams, M.

2018-03-01

A comparative research using three inert markers, chromic oxide, yttrium and ytterbium to measure the apparent nutrient digestibility of experimental feed in juvenile Hybrid abalone (Haliotis rubra X H. laevigata) and Greenlip abalone (H.laevigata) revealed that apparent digestibility of crude protein (ADCP) measured using yttrium and ytterbium in hybrid abalone were significantly different across the treatments. Protein digestibility measured in experimental tanks was higher than those measured in indoor and outdoor commercial tanks, regardless of inert marker used. Chromic oxide led to overestimated ADCP compared to when measured using yttrium and ytterbium. There were no significant interactions between temperature and inert markers when measuring ADCP and apparent digestibility of gross energy (ADGE). However, there was a significant difference of ADCP amongst inert markers when measured in greenlip abalone cultured at two temperatures. While measurements of ADge calculated using three inert markers shared the same value.

Digestibility of animal and vegetable protein ingredients by pirarucu juveniles, Arapaima gigas

Directory of Open Access Journals (Sweden)

Filipe dos Santos Cipriano

Full Text Available ABSTRACT The objective of this study was to determine the apparent digestibility coefficients of energy, protein, and amino acids in protein ingredients by pirarucu juveniles. A test was conducted with six protein ingredients: meat and bone meal, fish meal, hydrolyzed feather meal, poultry by-product meal, soybean meal, and corn gluten meal. Three repetitions were used for each tested ingredient. A reference feed was used with 430 g kg−1 crude protein and 19.63 kJ g−1 gross energy. The test feeds consisted of the replacement of 30% of the reference feeds with the test ingredients. Chromium oxide was added to the feeds at 1 g kg−1 as an external marker. Eighteen juveniles with an average weight of 235±36 g were used. The best apparent digestibility coefficients of protein were found for fish meal, followed by the poultry by-product meal and meat and bone meal. However, except for gluten, all the tested ingredients presented protein digestibilities above 0.70. The crude energy apparent digestibility coefficient was higher for animal ingredients, above 0.75, than for vegetable ingredients, which presented values below 0.60. Pirarucu efficiently uses the protein from the tested ingredients, regardless of origin. However, it has a preferential ability to use the energy from animal ingredients.

Plastic Trash goes Biohybrid"-Rapid and Selective Functionalization of Inert Plastic Surfaces with Biomolecules

DEFF Research Database (Denmark)

Schiller, Stefan M; Kambhampati, Dev; Stengel, Gudrun

2010-01-01

The covalent functionalization of "inert" polymers such as polypropylene with biomolecules for biocompatible or biosensor surfaces is challenging. Here we present a powerful approach to covalently modify "inert" macromolecular surfaces with biomacromolecules reusing old plastic material. A special...... emphasis was placed on easily accessible materials and a process which is easy, fast, efficient, cheap, and reliable. "Plastic trash" (lids from Eppendorf® pipet tip containers) was used as a polymer substrate to demonstrate the use/reuse of commercial packing material to covalently modify this material...

Safety assessment of Vitis vinifera (grape)-derived ingredients as used in cosmetics.

Science.gov (United States)

Fiume, Monice M; Bergfeld, Wilma F; Belsito, Donald V; Hill, Ronald A; Klaassen, Curtis D; Liebler, Daniel C; Marks, James G; Shank, Ronald C; Slaga, Thomas J; Snyder, Paul W; Andersen, F Alan

2014-01-01

The Cosmetic Ingredient Review Expert Panel (Panel) assessed the safety of 24 Vitis vinifera (grape)-derived ingredients and found them safe in the present practices of use and concentration in cosmetics. These ingredients function in cosmetics mostly as skin-conditioning agents, but some function as antioxidants, flavoring agents, and/or colorants. The Panel reviewed the available animal and clinical data to determine the safety of these ingredients. Additionally, some constituents of grapes have been assessed previously for safety as cosmetic ingredients by the Panel, and others are compounds that have been discussed in previous Panel safety assessments. © The Author(s) 2014.

Development of unidentified dna-specific hif 1α gene of lizard (hemidactylus platyurus) which plays a role in tissue regeneration process

Science.gov (United States)

Novianti, T.; Sadikin, M.; Widia, S.; Juniantito, V.; Arida, E. A.

2018-03-01

Development of unidentified specific gene is essential to analyze the availability these genes in biological process. Identification unidentified specific DNA of HIF 1α genes is important to analyze their contribution in tissue regeneration process in lizard tail (Hemidactylus platyurus). Bioinformatics and PCR techniques are relatively an easier method to identify an unidentified gene. The most widely used method is BLAST (Basic Local Alignment Sequence Tools) method for alignment the sequences from the other organism. BLAST technique is online software from website https://blast.ncbi.nlm.nih.gov/Blast.cgi that capable to generate the similar sequences from closest kinship to distant kindship. Gecko japonicus is a species that it has closest kinship with H. platyurus. Comparing HIF 1 α gene sequence of G. japonicus with the other species used multiple alignment methods from Mega7 software. Conserved base areas were identified using Clustal IX method. Primary DNA of HIF 1 α gene was design by Primer3 software. HIF 1α gene of lizard (H. platyurus) was successfully amplified using a real-time PCR machine by primary DNA that we had designed from Gecko japonicus. Identification unidentified gene of HIF 1a lizard has been done successfully with multiple alignment method. The study was conducted by analyzing during the growth of tail on day 1, 3, 5, 7, 10, 13 and 17 of lizard tail after autotomy. Process amplification of HIF 1α gene was described by CT value in real time PCR machine. HIF 1α expression of gene is quantified by Livak formula. Chi-square statistic test is 0.000 which means that there is a different expression of HIF 1 α gene in every growth day treatment.

Ingredients derived from the slaughter of bovines in dog food

Directory of Open Access Journals (Sweden)

Karina De Carli Loureiro

Full Text Available ABSTRACT: This study evaluated the nutritional levels, apparent digestibility coefficients, and faecal characteristics of dogs fed with four by-products from bovine slaughter: testicles, residue sirloin steak, trachea, and liver. Ingredients were processed and packed in tins for heat treatment in autoclaves. For the digestibility and faeces quality, ingredients were mixed with a reference diet (commercial food in the proportion of 30g kg-1 test ingredient and 70g kg-1 reference diet (as dry matter. Ten adult dogs were distributed in double Latin block squares (5x5 with five treatments and five periods, totalling ten repetitions per treatment. The residue sirloin steak presented the highest levels of essential (414.2g kg-1 of dry matter and non-essential (399.0g kg-1 of dry matter amino acids in tested ingredients. No differences (P>0.05 were observed in apparent digestibility coefficients of dry matter - ADCDM (907g kg-1, ADCOM (930g kg-1, ADCCP (841g kg-1, ADCAEE (954g kg-1 values, and DE (5069kcal kg-1 and ME (4781kcal kg-1 values between testicle, residue sirloin steak, and liver. The trachea presented lower digestibility and energy values (digestible and metabolizable than the other ingredients. This lower trachea digestibility resulted in higher faecal volume for natural and dry matter (P0.05 in faecal score between ingredients. Ingredients tested in this study can be used in feeds for adult dogs; however, their nutritional levels and digestibility values should be considered for correct diet balance.

76 FR 36356 - C9

Science.gov (United States)

2011-06-22

... extremely conservative assessment of dietary risk due to a series of compounded conservatisms. First... product relative to that of the active ingredient. Second, the conservatism of this methodology is... third compounding conservatism is EPA's assumption that all foods contain the inert ingredient at the...

Oil Dispersion with Abamectin as Active Ingredient

Directory of Open Access Journals (Sweden)

Slavica Gašić

2011-01-01

Full Text Available Abamectin was developed as an insecticide, nematocide and acaricide for use on a varietyof agricultural and horticultural crops. The products with this active ingredient can befound on the market mostly formulated as emulsifiable concentrate (EC. Usually producersrecommend using the EC formulation of abamectin together with some kind of adjuvants(natural oils to improve efficacy of the active ingredient. To overcome the efficacy problemwe tried to formulate the active ingredient abamectin as oil dispersion (OD. Oil dispersion,preferably based on naturally derived oils could improve pesticide efficacy. This type of pesticideformulation contains oil instead of water as in classical suspension concentrate andtypically has better retention and coverage. In the case of abamectin, in this investigationsoybean oil was used with the mixture of different nonionic emulsifiers. Content of abamecetinin formulation was 1.8 %. The developed formulation was tested for few importantparameters. The obtained physicochemical properties for the above mentioned formulationhave shown that it is stable and could be used in plant protection.

Radiation processing of dry food ingredients - a review

International Nuclear Information System (INIS)

Farkas, J.

1985-01-01

Radiation decontamination of dry ingredients, herbs and enzyme preparations is a technically feasible, economically viable and safe physical process. The procedure is direct, simple, requires no additives, does not leave residues and is highly efficient. Its dose requirement is moderate. Radiation doses of 3 to 10 kGy proved to be sufficient to reduce the viable cell counts to a satisfactory level. Ionizing radiations do not cause any significant rise in temperature and the flavour, texture or other important technological or sensory properties of most ingredients are not influenced at radiation doses necessary for a satisfactory decontamination. The microflora surviving the cell-count reduction by irradiation is more sensitive to subsequent food processing treatments than the microflora of untreated ingredients. Recontamination can be prevented since the product can be irradiated in its final packaging. Irradiation can be carried out in commercial containers and it results in considerable savings of energy and labour as compared to alternative decontamination techniques. Radiation processing of dry ingredients is an emerging technology in several countries and more and more clearances on irradiated foods are issued or expected to be granted in the near future. (author)

Radiation processing of dry food ingredients - a review

Energy Technology Data Exchange (ETDEWEB)

Farkas, J

1985-01-01

Radiation decontamination of dry ingredients, herbs and enzyme preparations is a technically feasible, economically viable and safe physical process. The procedure is direct, simple, requires no additives, does not leave residues and is highly efficient. Its dose requirement is moderate. Radiation doses of 3 to 10 kGy proved to be sufficient to reduce the viable cell counts to a satisfactory level. Ionizing radiations do not cause any significant rise in temperature and the flavour, texture or other important technological or sensory properties of most ingredients are not influenced at radiation doses necessary for a satisfactory decontamination. The microflora surviving the cell-count reduction by irradiation is more sensitive to subsequent food processing treatments than the microflora of untreated ingredients. Recontamination can be prevented since the product can be irradiated in its final packaging. Irradiation can be carried out in commercial containers and it results in considerable savings of energy and labour as compared to alternative decontamination techniques. Radiation processing of dry ingredients is an emerging technology in several countries and more and more clearances on irradiated foods are issued or expected to be granted in the near future.

Ingredients derived from the slaughter of bovines in dog food

OpenAIRE

Loureiro, Karina De Carli; Haese, Douglas; Kill, João Luís; Pires, Achicine Furno; Fernandes, Danieli Rankel; Colnago, Geraldo Luiz; Lucas, Wendius Henrique; Gama, Gabriela Oliveira

2017-01-01

ABSTRACT: This study evaluated the nutritional levels, apparent digestibility coefficients, and faecal characteristics of dogs fed with four by-products from bovine slaughter: testicles, residue sirloin steak, trachea, and liver. Ingredients were processed and packed in tins for heat treatment in autoclaves. For the digestibility and faeces quality, ingredients were mixed with a reference diet (commercial food) in the proportion of 30g kg-1 test ingredient and 70g kg-1 reference diet (as dry ...

Innovations in natural ingredients and their use in skin care.

Science.gov (United States)

Fowler, Joseph F; Woolery-Lloyd, Heather; Waldorf, Heidi; Saini, Ritu

2010-06-01

Natural ingredients have been used traditionally for millennia and their application in topical creams, lotions and preparations within the traditional medicines and healing traditions of many cultures has been observed. Over the last 20 years, clinical and laboratory studies have identified the benefits of an array of natural ingredients for skin care. Consequently, a number of these ingredients and compounds are today being developed, used or considered not only for anti-aging effects, but also for use in dermatologic disorders. Certain ingredients, such as colloidal oatmeal and aloe vera, have been identified as beneficial in the treatment of psoriasis and atopic dermatitis, respectively, due to their anti-inflammatory properties. For combating acne and rosacea, green tea, niacinamide and feverfew are considered efficacious. As to hyperpigmentation and antioxidative capabilities, licorice, green tea, arbutin, soy, acai berry, turmeric and pomegranate are among those plants and compounds found to be most beneficial. Additional research is needed to determine to confirm and elucidate the benefits of these ingredients in the prevention and management of skin disease.

Health Risk Assessment on Hazardous Ingredients in Household Deodorizing Products

Directory of Open Access Journals (Sweden)

Minjin Lee

2018-04-01

Full Text Available The inhalation of a water aerosol from a humidifier containing disinfectants has led to serious lung injuries in Korea. To promote the safe use of products, the Korean government enacted regulations on the chemicals in various consumer products that could have adverse health effects. Given the concern over the potential health risks associated with the hazardous ingredients in deodorizing consumer products, 17 ingredients were analyzed and assessed according to their health risk on 3 groups by the application type in 47 deodorizing products. The risk assessment study followed a stepwise procedure (e.g., collecting toxicological information, hazard identification/exposure assessment, and screening and detailed assessment for inhalation and dermal routes. The worst-case scenario and maximum concentration determined by the product purpose and application type were used as the screening assessment. In a detailed assessment, the 75th exposure factor values were used to estimate the assumed reasonable exposure to ingredients. The exposed concentrations of seven ingredients were calculated. Due to limitation of toxicity information, butylated hydroxyl toluene for a consumer’s exposure via the dermal route only was conducted for a detailed assessment. This study showed that the assessed ingredients have no health risks at their maximum concentrations in deodorizing products. This approach can be used to establish guidelines for ingredients that may pose inhalation and dermal hazards.

Health Risk Assessment on Hazardous Ingredients in Household Deodorizing Products

Science.gov (United States)

Lee, Minjin; Kim, Joo-Hyon; Lee, Daeyeop; Kim, Jaewoo; Lim, Hyunwoo; Seo, Jungkwan; Park, Young-Kwon

2018-01-01

The inhalation of a water aerosol from a humidifier containing disinfectants has led to serious lung injuries in Korea. To promote the safe use of products, the Korean government enacted regulations on the chemicals in various consumer products that could have adverse health effects. Given the concern over the potential health risks associated with the hazardous ingredients in deodorizing consumer products, 17 ingredients were analyzed and assessed according to their health risk on 3 groups by the application type in 47 deodorizing products. The risk assessment study followed a stepwise procedure (e.g., collecting toxicological information, hazard identification/exposure assessment, and screening and detailed assessment for inhalation and dermal routes). The worst-case scenario and maximum concentration determined by the product purpose and application type were used as the screening assessment. In a detailed assessment, the 75th exposure factor values were used to estimate the assumed reasonable exposure to ingredients. The exposed concentrations of seven ingredients were calculated. Due to limitation of toxicity information, butylated hydroxyl toluene for a consumer’s exposure via the dermal route only was conducted for a detailed assessment. This study showed that the assessed ingredients have no health risks at their maximum concentrations in deodorizing products. This approach can be used to establish guidelines for ingredients that may pose inhalation and dermal hazards. PMID:29652814

An investigation of the microstructures and properties of metal inert ...

Indian Academy of Sciences (India)

Abstract. Two different types of welds, Metal Inert Gas (MIG) and Friction Stir. Welding (FSW), have been used to weld aluminum alloy 5083. The microstructure of the welds, including the nugget zone and heat affected zone, has been compared in these two methods using optical microscopy. The mechanical properties of ...

Study of the spectral characteristics of unidentified galactic EGRET sources. Are they pulsar-like?

Science.gov (United States)

Merck, M.; Bertsch, D. L.; Dingus, B. L.; Esposito, J. A.; Fichtel, C. E.; Fierro, J. M.; Hartman, R. C.; Hunter, S. D.; Kanbach, G.; Kniffen, D. A.; Lin, Y. C.; Mayer-Hasselwander, H. A.; Michelson, P. F.; von Montigny, C.; Muecke, A.; Mukherjee, R.; Nolan, P. L.; Pohl, M.; Schneid, E.; Sreekumar, P.; Thompson, D. J.; Willis, T. D.

1996-12-01

A spectral study of unidentified galactic EGRET sources was performed. The derived spectra are compared to the spectra of pulsars to test the hypothesis, that a significant fraction of these sources are Geminga like radio-quiet pulsars (Yadigaroglu & Romani 1995ApJ...449..211Y). Most of the sources show significantly different spectra than expected under this hypothesis. Of those with spectra consistent with typical pulsar spectra, four are positionally consistent with young spin-powered radio pulsars leaving only very few Geminga type candidates in the sample.

Inert carriers for column extraction chromatography

International Nuclear Information System (INIS)

Katykhin, G.S.

1978-01-01

Inert carriers used in column extraction chromatography are reviewed. Such carriers are devided into two large groups: hydrophilic carriers which possess high surface energy and are well wetted only with strongly polar liquids (kieselguhrs, silica gels, glasses, cellulose, Al 2 O 3 ) and water-repellent carriers which possess low surface energy and are well wetted with various organic solvents (polyethylene, polytetrafluorethylene polytrifluorochlorethylene). Properties of various carriers are presented: structure, chemical and radiation stability, adsorption properties, extracting agent capacity. The effect of structure and sizes of particles on the efficiency of chromatography columns is considered. Ways of immovable phase deposition on the carrier and the latter's regeneration. Peculiarities of column packing for preparative and continuous chromatography are discussed

Seeded inert gas driven disk generator

International Nuclear Information System (INIS)

Joshi, N.K.; Venkatramani, N.; Rohatgi, V.K.

1987-01-01

This report outlines the present status of work being carried out in closed cycle MHD and disk generators. It gives the basic principles and discusses a proposal for setting up an experimental facility to study nonequilibrium plasmas using an inert gas driven disk generator. Disk geometry is a near ideal geometry for plasma studies since it has single or few pair electrodes combined with near perfect insulating walls. The proposed outlay of facility with components and subsystem is given. The facility may also be used to study the concept of fully ionized seed and to develop advanced diagnostic techniques. The absic equation describing the working parameters of such a system is also given in the Appendix. (author). 57 refs

Inert doublet dark matter with an additional scalar singlet and 125 GeV Higgs boson

Energy Technology Data Exchange (ETDEWEB)

Dutta Banik, Amit; Majumdar, Debasish [Saha Institute of Nuclear Physics, Astroparticle Physics and Cosmology Division, Kolkata (India)

2014-11-15

In this work we consider a model for particle dark matter where an extra inert Higgs doublet and an additional scalar singlet is added to the Standard Model (SM) Lagrangian. The dark matter candidate is obtained from only the inert doublet. The stability of this one component dark matter is ensured by imposing a Z{sub 2} symmetry on this additional inert doublet. The additional singlet scalar has a vacuum expectation value (VEV) and mixes with the Standard Model Higgs doublet, resulting in two CP even scalars h{sub 1} and h{sub 2}. We treat one of these scalars, h{sub 1}, to be consistent with the SM Higgs-like boson of mass around 125 GeV reported by the LHC experiment. These two CP even scalars contribute to the annihilation cross section of this inert doublet dark matter, resulting in a larger dark matter mass region that satisfies the observed relic density. We also investigate the h{sub 1} → γγ and h{sub 1} → γ Z processes and compared these with LHC results. This is also used to constrain the dark matter parameter space in the present model. We find that the dark matter candidate in the mass region 60-80 GeV (m{sub 1} = 125 GeV, mass of h{sub 1}) satisfies the recent bound from LUX direct detection experiment. (orig.)

EGRET Unidentified Source Radio Observations and Performance of Receiver Gain Calibration

International Nuclear Information System (INIS)

Niinuma, Kotaro; Asuma, Kuniyuki; Kuniyoshi, Masaya; Matsumura, Nobuo; Takefuji, Kazuhiro; Kida, Sumiko; Takeuchi, Akihiko; Ichikawa, Hajime; Sawano, Akihiro; Yoshimura, Naoya; Suzuki, Shigehiro; Nakamura, Ryosuke; Nakayama, Yu; Daishido, Tsuneaki

2006-01-01

Last year, we have developed the receiver gain calibration system by using Johnson-Nyquist noise, for accuracy flux measurement, because we have been starting radio identification program of transient radio sources, blazars and radio counterpart of The Energetic Gamma Ray Experiment Telescope (EGRET) unidentified γ-ray sources in Waseda Nasu Pulsar Observatory. It is shown that there are a few low correlation data between receiver gain and ambient temperature around receiver for anything troubles of receiver, because we can detect gain and ambient temperature through a day by developed system. Estimated fluctuations of daily data of steady sources decrease by removing low correlation data before analysing. As the result of our analysis by using above system, radio counterpart of EGRET identified source showed fading light-curve for a week

Performances of continuous dryer with inert medium fluidized bed

Directory of Open Access Journals (Sweden)

Arsenijević Zorana Lj.

2008-01-01

Full Text Available A fluid bed dryer with inert particles represents a very attractive alternative to other drying technologies according to the main efficiency criteria, i.e. specific water evaporation rate, specific heat consumption and speci­fic air consumption. A high drying efficiency results from the large con­tact area and from the large temperature difference between the inlet and outlet air. A rapid mixing of the particles leads to nearly isothermal conditions throughout the bed. A fluid bed dryer with inert particles was used for drying of slurries. Experiments were performed in a cylindrical column 215 mm in diameter with glass spheres as inert particles. In this paper, results of drying experi­ments with slurries of Zineb fungicide, copper hydroxide, calcium carbo­nate and pure water used as the feed material are presented. In our fluidized bed we successfully dried a number of other materials such as: fungicides and pesticides (Ziram, Propineb, Mangozeb, copper oxy-chloride, copper oxy-sulphate, Bordeaux mixture, other inorganic compounds (calcium sulphate, cobalt carbonate, electrolytic copper, sodium chloride, and a complex compound (organo-bentonite. The effects of operating conditions on dryer throughput and product quality were investigated. Main performance criteria, i.e. specific water evaporation rate, specific heat consumption and specific air consumption, were quantified. Temperature profile along the bed was mapped, and nearly isothermal conditions were found due to thorough mixing of the particles. Analysis of drying and energy efficiencies as a function of inlet and outlet air temperature difference was performed for deeper insight in dryer behavior and for optimizing dryer design and operation from an energy point of view. A simple mathematical model based on an overall heat balance predicts the dryer performance quite well. The industrial prototype with fluid bed of 0.8 m in diameter and capacity 650 kg of evaporated moisture per

21 CFR 333.110 - First aid antibiotic active ingredients.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false First aid antibiotic active ingredients. 333.110... (CONTINUED) DRUGS FOR HUMAN USE TOPICAL ANTIMICROBIAL DRUG PRODUCTS FOR OVER-THE-COUNTER HUMAN USE First Aid Antibiotic Drug Products § 333.110 First aid antibiotic active ingredients. The product consists of any of...

Multisized Inert Particle Loading for Solid Rocket Axial Combustion Instability Suppression

Directory of Open Access Journals (Sweden)

David R. Greatrix

2012-01-01

Full Text Available In the present investigation, various factors and trends, related to the usage of two or more sets of inert particles comprised of the same material (nominally aluminum but at different diameters for the suppression of axial shock wave development, are numerically predicted for a composite-propellant cylindrical-grain solid rocket motor. The limit pressure wave magnitudes at a later reference time in a given pulsed firing simulation run are collected for a series of runs at different particle sizes and loading distributions and mapped onto corresponding attenuation trend charts. The inert particles’ presence in the central core flow is demonstrated to be an effective means of instability symptom suppression, in correlating with past experimental successes in the usage of particles. However, the predicted results of this study suggest that one needs to be careful when selecting more than one size of particle for a given motor application.

Thermodynamic stability and kinetic inertness of a Gd-DTPA bisamide complex grafted onto gold nanoparticles.

Science.gov (United States)

Mogilireddy, Vijetha; Déchamps-Olivier, Isabelle; Alric, Christophe; Laurent, Gautier; Laurent, Sophie; Vander Elst, Luce; Muller, Robert; Bazzi, Rana; Roux, Stéphane; Tillement, Olivier; Chuburu, Françoise

2015-01-01

Gold nanoparticles coated by gadolinium (III) chelates (Au@DTDTPA) where DTDTPA is a dithiolated bisamide derivative of diethylenetriamine-N,N,N',N'',N''-pentaacetic acid (DTPA), constituted contrast agents for both X-ray computed tomography and magnetic resonance imaging. In an MRI context, highly stable Gd(3+) complexes are needed for in vivo applications. Thus, knowledge of the thermodynamic stability and kinetic inertness of these chelates, when grafted onto gold nanoparticles, is crucial since bisamide DTPA chelates are usually less suited for Gd(3+) coordination than DTPA. Therefore, these parameters were evaluated by means of potentiometric titrations and relaxivity measurements. The results showed that, when the chelates were grafted onto the nanoparticle, not only their thermodynamic stability but also their kinetic inertness were improved. These positive effects were correlated to the chelate packing at the nanoparticle surface that stabilized the corresponding Gd(3+) complexes and greatly enhanced their kinetic inertness. Copyright © 2014 John Wiley & Sons, Ltd.

Lactose in dairy ingredients: Effect on processing and storage stability.

Science.gov (United States)

Huppertz, Thom; Gazi, Inge

2016-08-01

Lactose is the main carbohydrate in the milk of most species. It is present in virtually all dry dairy ingredients, with levels ranging from lactose powders. The presence of lactose has a strong effect on ingredient processing and stability. Lactose can negatively influence powder properties and lead to undesirable effects, such as the stickiness of powder resulting in fouling during drying, or caking and related phenomena during storage. In addition, being a reducing carbohydrate, lactose can also participate in the Maillard reaction with free amino groups of proteins, peptides, and free AA. In this review, the influence of the presence (or absence) of lactose on physiochemical properties of dairy ingredients is reviewed, with particular emphasis on behavior during processing and storage. Particularly important features in this respect are whether lactose is in the (glassy) amorphous phase or in the crystalline phase, which is strongly affected by precrystallization conditions (e.g., in lactose, permeate, and whey powders) and by drying conditions. Furthermore, the moisture content and water activity of the ingredients are important parameters to consider, as they determine both mobility and reactivity, influencing Maillard reactions and concomitant browning, the crystallization of amorphous lactose during storage of dairy ingredients, glass transitions temperatures, and associated stickiness and caking phenomena. For the stickiness and caking, a crucial aspect to take into account is powder particle surface composition in relation to the bulk powder. Lactose is typically underrepresented at the powder surface, as a result of which deviations between observed lactose-induced caking and stickiness temperatures, and determined glass transition temperatures arise. By considering lactose as an integral part of ingredient composition along with all other compositional and environmental properties, lactose behavior in dairy ingredients can be understood, controlled, and

Inert dusts and their effects on the poultry red mite (Dermanyssus gallinae)

DEFF Research Database (Denmark)

Kilpinen, Ole; Steenberg, Tove

2009-01-01

commonly applied alternative control methods for poultry red mite in Europe. This development has occurred despite a lack of knowledge of the efficacy of the different types of inert dusts and how this is affected by environmental parameters, e.g. the high relative humidity found in poultry houses....... In this laboratory study the efficacy of different commercial inert dust products against D. gallinae is compared. All tested compounds killed mites, but there was a clear ranking of efficacy (measured as weight loss after 24 h and as time until 50% mortality), particularly at 75% relative humidity (RH). At 85% RH...

Radiative neutrino mass and Majorana dark matter within an inert Higgs doublet model

Science.gov (United States)

Ahriche, Amine; Jueid, Adil; Nasri, Salah

2018-05-01

We consider an extension of the standard model (SM) with an inert Higgs doublet and three Majorana singlet fermions to address both origin and the smallness of neutrino masses and dark matter (DM) problems. In this setup, the lightest Majorana singlet fermion plays the role of DM candidate and the model parameter space can be accommodated to avoid different experimental constraints such as lepton flavor violating processes and electroweak precision tests. The neutrino mass is generated at one-loop level a la Scotogenic model and its smallness is ensured by the degeneracy between the C P -odd and C P -even scalar members of the inert doublet. Interesting signatures at both leptonic and hadronic colliders are discussed.

Models of bending strength for Gilsocarbon graphites irradiated in inert and oxidising environments

International Nuclear Information System (INIS)

Eason, Ernest D.; Hall, Graham N.; Marsden, Barry J.; Heys, Graham B.

2013-01-01

This paper presents the development and validation of an empirical model of fast neutron damage and radiolytic oxidation effects on bending strength for the moulded Gilsocarbon graphites used in Advanced Gas-cooled Reactors (AGRs). The inert environment model is based on evidence of essentially constant strength as fast neutron dose increases in inert environment. The model of combined irradiation and oxidation calibrates that constant along with an exponential function representing the degree of radiolytic oxidation as measured by weight loss. The change in strength with exposure was found to vary from one AGR station to another. The model was calibrated to data on material trepanned from AGR moderator bricks after varying operating times

TIG AISI-316 welds using an inert gas welding chamber and different filler metals: Changes in mechanical properties and microstructure

Energy Technology Data Exchange (ETDEWEB)

Pascual, M.; Salas, F.; Carcel, F.J.; Perales, M.; Sanchez, A.

2010-07-01

This report analyses the influence of the use of an inert gas welding chamber with a totally inert atmosphere on the microstructure and mechanical properties of austenitic AISI 316L stainless steel TIG welds, using AISI ER316L, AISI 308L and Inconel 625 as filler metals. When compared with the typical TIG process, the use of the inert gas chamber induced changes in the microstructure, mainly an increase in the presence of vermicular ferrite and ferrite stringers, what resulted in higher yield strengths and lower values of hardness. Its effect on other characteristics of the joins, such as tensile strength, depended on the filler metal. The best combination of mechanical characteristics was obtained when welding in the inert gas chamber using Inconel 625 as filler metal. (Author). 12 refs.

A chemically inert drug can stimulate T cells in vitro by their T cell receptor in non-sensitised individuals

International Nuclear Information System (INIS)

Engler, Olivier B.; Strasser, Ingrid; Naisbitt, Dean J.; Cerny, Andreas; Pichler, Werner J.

2004-01-01

Drugs can interact with T cell receptors (TCR) after binding to peptide-MHC structures. This binding may involve the formation of a stable, covalent bond between a chemically reactive drug and MHC or the peptide embedded within. Alternatively, if the drug is chemically inert, the binding may be non-covalent and readily reversible. Both types of drug presentation account for a substantial number of adverse side effects to drugs. Presently no tests are available to predict the ability of chemically inert drugs to stimulate an immune response. Here we present data on the successful induction of a primary T cell immune response in vitro against a chemically inert drug using blood from healthy individuals, previously not exposed to the drug. Blood lymphocytes were stimulated by the chemically inert drug sulfamethoxazole and the protein-reactive drug-metabolite sulfamethoxazole-nitroso in the presence of IL-2. 9/10 individuals reacted in response to sulfamethoxazole-nitroso, but only three reacted to the chemically inert compound sulfamethoxazole. Drug reactive T cells could be detected after 14-35 days of cell culture by drug-specific proliferation or cytotoxicity, which was MHC-restricted. These cells were CD4, CD8 positive or CD4/CD8 double positive and T cell clones generated secreted Th0 type cytokines. Drug interaction lead to down-regulation of specific TCR. These data confirm the ability of chemically inert drugs to stimulate certain T cells by their TCR and may provide the opportunity to screen new drugs for their ability to interact with TCRs

Galloyl-RGD as a new cosmetic ingredient

Science.gov (United States)

2014-01-01

Background The cosmetics market has rapidly increased over the last years. For example, in 2011 it reached 242.8 billion US dollars, which was a 3.9% increase compared to 2010. There have been many recent trials aimed at finding the functional ingredients for new cosmetics. Gallic acid is a phytochemical derived from various herbs, and has anti-fungal, anti-viral, and antioxidant properties. Although phytochemicals are useful as cosmetic ingredients, they have a number of drawbacks, such as thermal stability, residence time in the skin, and permeability through the dermal layer. To overcome these problems, we considered conjugation of gallic acid with a peptide. Results We synthesized galloyl-RGD, which represents a conjugate of gallic acid and the peptide RGD, purified it by HPLC and characterized by MALDI-TOF with the aim of using it as a new cosmetic ingredient. Thermal stability of galloyl-RGD was tested at alternating temperatures (consecutive 4°C, 20°C, or 40°C for 8 h each) on days 2, 21, 41, and 61. Galloyl-RGD was relatively safe to HaCaT keratinocytes, as their viability after 48 h incubation with 500 ppm galloyl-RGD was 93.53%. In the group treated with 50 ppm galloyl-RGD, 85.0% of free radicals were removed, whereas 1000 ppm galloyl-RGD suppressed not only L-DOPA formation (43.8%) but also L-DOPA oxidation (54.4%). Conclusions Galloyl-RGD is a promising candidate for a cosmetic ingredient. PMID:25103826

The Influence of Suspended Inert Solid Particles on Zinc Corrosion

DEFF Research Database (Denmark)

Bech-Nielsen, Gregers

1996-01-01

The rate of corrosion of electroplated zinc in near-neutral chloride solutions can be lowered by as much as 75% by adding fine, inert particles of substances such as MnO2, Fe3O4, SiC and TiN to the well-stirred solution. Spreading of local areas of etching is also stopped. Copyright (C) 1996...

A new world of ingredients

DEFF Research Database (Denmark)

Halloran, Afton Marina Szasz; Flore, Roberto

2018-01-01

Insects have been absent from European diets with only few regional exceptions, making them an uncommon ingredient in the kitchens of fine dining establishments. This chapter investigates whether a piece the puzzle of understanding the temporality or permanence of edible insects in modern Europea...

Encapsulation of new active ingredients

Science.gov (United States)

The organic construct consumed as food comes packaged in units that carry the active components, protects the entrapped active materials until delivered to targeted human organ. The packaging and delivery role is mimicked in the microencapsulation tools used to deliver active ingredients in process...

Process for separation of inert fission gases for waste gas of a reprocessing plant for nuclear fuel

International Nuclear Information System (INIS)

Schnez, H.

1980-01-01

The inert fission gases Kr and Xe released in the resolver and other waste gases are taken to an acid regeneration plant. Part of the inert fission gases is separated by compression, cooling and filtering and deposited. The other part flows back to the resolver as flushing gas so that a flushing gas circuit is formed, which prevents explosive gas mixtures occurring. (DG) [de

Inert gases in a terra sample - Measurements in six grain-size fractions and two single particles from Lunar 20.

Science.gov (United States)

Heymann, D.; Lakatos, S.; Walton, J. R.

1973-01-01

Review of the results of inert gas measurements performed on six grain-size fractions and two single particles from four samples of Luna 20 material. Presented and discussed data include the inert gas contents, element and isotope systematics, radiation ages, and Ar-36/Ar-40 systematics.

TIG AISI-316 welds using an inert gas welding chamber and different filler metals: Changes in mechanical properties and microstructure

Directory of Open Access Journals (Sweden)

Sánchez, A.

2010-12-01

Full Text Available This report analyses the influence of the use of an inert gas welding chamber with a totally inert atmosphere on the microstructure and mechanical properties of austenitic AISI 316L stainless steel TIG welds, using AISI ER316L, AISI 308L and Inconel 625 as filler metals. When compared with the typical TIG process, the use of the inert gas chamber induced changes in the microstructure, mainly an increase in the presence of vermicular ferrite and ferrite stringers, what resulted in higher yield strengths and lower values of hardness. Its effect on other characteristics of the joins, such as tensile strength, depended on the filler metal. The best combination of mechanical characteristics was obtained when welding in the inert gas chamber using Inconel 625 as filler metal.

En este estudio se analiza la influencia que el uso de una cámara de soldadura de gas inerte tiene sobre la microestructura y las propiedades mecánicas de las soldaduras TIG en el acero inoxidable austenítico AISI-316L cuando se emplean AISI ER316L, AISI 308L e Inconel 625 como materiales de aporte. Cuando se compara con el típico proceso de TIG, el uso de una cámara de gas inerte induce cambios en la microestructura, incrementando la presencia de ferrita vermicular y de laminillas de ferrita, resultando en un aumento del límite elástico y una pérdida de dureza. Su influencia sobre otras características de las soldaduras como la carga de rotura depende de la composición del material de aporte. La mejor combinación de propiedades mecánicas se obtuvo usando el Inconel 625 como material de aporte y soldando en la cámara de gas inerte.

Arc melting in inert gas atmosphere of zirconium sponge

International Nuclear Information System (INIS)

Julio Junior, O.; Andrade, A.H.P. de

1991-01-01

The obtainment of metallic zirconium in laboratory scale with commercial and nuclear quality is the objective of the Metallurgy Department of IEN/CNEN - Brazil, so a melting procedure of zirconium sponge in laboratory scale using an arc furnace in inert atmosphere is developed. The effects of atmosphere operation, and the use of gas absorber and the sponge characteristics over the quality of button in as-cast reporting with hardness measures are described. (C.G.C.)

7 CFR 205.305 - Multi-ingredient packaged products with less than 70 percent organically produced ingredients.

Science.gov (United States)

2010-01-01

... Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... organically produced ingredients may only identify the organic content of the product by: (1) Identifying each... statement, displaying the product's percentage of organic contents on the information panel. (b...

What Is "Natural"? Consumer Responses to Selected Ingredients.

Science.gov (United States)

Chambers, Edgar; Chambers, Edgar; Castro, Mauricio

2018-04-23

Interest in “natural” food has grown enormously over the last decade. Because the United States government has not set a legal definition for the term “natural”, customers have formed their own sensory perceptions and opinions on what constitutes natural. In this study, we examined 20 ingredients to determine what consumers consider to be natural. Using a national database, 630 consumers were sampled (50% male and 50% female) online, and the results were analyzed using percentages and chi-square tests. No ingredient was considered natural by more than 69% of respondents. We found evidence that familiarity may play a major role in consumers’ determination of naturalness. We also found evidence that chemical sounding names and the age of the consumer have an effect on whether an ingredient and potentially a food is considered natural. Interestingly, a preference towards selecting GMO (genetically modified organisms) foods had no significant impact on perceptions of natural.

Vector boson fusion in the inert doublet model

Science.gov (United States)

Dutta, Bhaskar; Palacio, Guillermo; Restrepo, Diego; Ruiz-Álvarez, José D.

2018-03-01

In this paper we probe the inert Higgs doublet model at the LHC using vector boson fusion (VBF) search strategy. We optimize the selection cuts and investigate the parameter space of the model and we show that the VBF search has a better reach when compared with the monojet searches. We also investigate the Drell-Yan type cuts and show that they can be important for smaller charged Higgs masses. We determine the 3 σ reach for the parameter space using these optimized cuts for a luminosity of 3000 fb-1 .

Nuclear EMP: ingredients of an EMP protection engineering methodology

International Nuclear Information System (INIS)

Latorre, V.R.; Spogen, L.R. Jr.

1977-02-01

A fundamental methodology of electromagnetic pulse (EMP) protection engineering is described. Operations performed within the framework of this methodology are discussed. These operations, along with problem constraints and data, constitute the essential ingredients needed to implement the overall engineering methodology. Basic definitions and descriptions of these essential ingredients are provided. The issues discussed represent the first step in developing a methodology for protecting systems against EMP effects

Zooplankton data collected from unidentified platforms in Coastal Waters of Washington / Oregon; 22 May 1979 to 06 August 1980 (NODC Accession 9800143)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Zooplankton data were collected using zooplankton net and bottle casts in Coastal Waters of Washington / Oregon from unidentified platforms from Canada. Data were...

Possible 85Kr influence on the plant metabolism. Investigation of inert gas 85Kr interaction with plants

International Nuclear Information System (INIS)

Butkus, D.

1999-01-01

Model experiments have shown that inert gas 85 Kr is accumulated by plants. The aim of the work was to determine the way of the capture of inert gas by growing plants: either only through their overground part from air or in addition through their overground part from air or in addition through roots which accumulate water dissolved materials. For this purpose potatoes were grown in the chamber where the 85 Kr volume activity was (3.6±0.1)*10 6 Bq*m -3 . It was determined that 85 Kr gas accumulation was greater in those plant parts which grow faster and are further from the soil. Measurement results of 85 Kr activity of a potato tuber slightly differed from the environment background activity. It shows that the main penetration of inert gas into the plant occurred by absorption from air. (author)

Natural ingredients based cosmetics. Content of selected fragrance sensitizers

DEFF Research Database (Denmark)

Rastogi, Suresh Chandra; Johansen, J D; Menné, T

1996-01-01

In the present study, we have investigated 42 cosmetic products based on natural ingredients for content of 11 fragrance substances: geraniol, hydroxycitronellal, eugenol, isoeugenol, cinnamic aldehyde, cinnamic alcohol, alpha-amylcinnamic aldehyde, citral, coumarin, dihydrocoumarin and alpha......-hexylcinnamic aldehyde. The study revealed that the 91% (20/22) of the natural ingredients based perfumes contained 0.027%-7.706% of 1 to 7 of the target fragrances. Between 1 and 5 of the chemically defined synthetic constituents of fragrance mix were found in 82% (18/22) of the perfumes. 35% (7/20) of the other...... of hydroxycitronellal and alpha-hexylcinnamic aldehyde in some of the products demonstrates that artificial fragrances, i.e., compounds not yet regarded as natural substances, may be present in products claimed to be based on natural ingredients....

Study on Chinese herbal medicine active ingredients labelled with tritium

International Nuclear Information System (INIS)

Dong Mo; Bao Guangliang

2008-01-01

Chinese medicinal herb active ingredients was labeled with triteium by using exchange of new synthesized tritiated water or exchange of low-pressure gas-liquid. The active ingredients was Genipin, acetylalkannin and chlorogenic acid .The radiochemical purity of the three labeled compounds were more than 95% after TLC and HPLC purification. The specific activities of tritium labeled-genipin, acetylalkannin and chlorogenic acid were 5.97, 3.24 and 470 GBq/g, respectively. The results indicated that the unstable Chinese medicinal herb active ingredients could be labeled with tritium by the methods of exchange of new synthesized tritiated water and exchange of low-pressure gas-liquid. (authors)

Fabrication of Miniature Titanium Capsule for Brachytherapy Sources Using Tungsten Inert Gas Method

International Nuclear Information System (INIS)

Naghdi, R.; Sheibani, Sh.; Tamizifar, M.

2013-01-01

The capsules containing radioactive materials as brachytherapy sources are used for implanting into some target organs for malignant disorders treatments, such as prostate, eyes, and brain cancers. The conventional method for sealing the tubes is to weld them using a laser beam which is now a part of tube melting methods (self welding). The purpose of this study was to seal miniature titanium tubes containing radioactive materials in the form of capsules. This study introduced a new method based on melting process. A piece of commercially pure titanium grade 2 in the form of disk was used for the experiment. The sample was melted at the top of the tube by a Tungsten Inert Gas welding device for a short time duration. After completion of the melting, the disk in the form of a drop was mixed with a small part of it and both were solidified and hence closed the tube. We evaluated the tubes for the metallurgical properties and seal process which took place by Tungsten Inert Gas in different zones, including the heat affected zone, fusion zone, and interface of the joint of the drop to the tube. Finally, the produced samples were tested according to the ISO2919 and ISO9978 and the results confirmed the Disk and Tungsten Inert Gas procedure.

Demand-Based Optimal Design of Storage Tank with Inerter System

Directory of Open Access Journals (Sweden)

Shiming Zhang

2017-01-01

Full Text Available A parameter optimal design method for a tank with an inerter system is proposed in this study based on the requirements of tank vibration control to improve the effectiveness and efficiency of vibration control. Moreover, a response indicator and a cost control indicator are selected based on the control targets for liquid storage tanks for simultaneously minimizing the dynamic response and controlling costs. These indicators are reformulated through a random vibration analysis under virtual excitation. The problem is then transformed from a multiobjective optimization problem to a single-objective nonlinear problem using the ε-constraint method, which is consistent with the demand-based method. White noise excitation can be used to design the tank with the inerter system under seismic excitation to simplify the calculation. Subsequently, a MATLAB-based calculation program is compiled, and several optimization cases are examined under different excitation conditions. The effectiveness of the demand-based method is proven through a time history analysis. The results show that specific vibration control requirements can be met at the lowest cost with a simultaneous reduction in base shears and overturning base moments.

Using fumarolic inert gas composition to investigate magma dynamics at Campi Flegrei (Italy)

Science.gov (United States)

Chiodini, G.; Caliro, S.; Paonita, A.; Cardellini, C.

2013-12-01

Since 2000 the Campi Flegrei caldera sited in Neapolitan area (Italy), has showed signs of reactivation, marked by ground uplift, seismic activity, compositional variations of fumarolic effluents from La Solfatara, an increase of the fumarolic activity as well as of soil CO2 fluxes. Comparing long time series of geochemical signals with ground deformation and seismicity, we show that these changes are at least partially caused by repeated injections of magmatic fluid into the hydrothermal system. The frequency of these degassing episodes has increased in the last years, causing pulsed uplift episodes and swarms of low magnitude earthquakes. We focus here in the inert gas species (CO2-He-Ar-N2) of Solfatara fumaroles which displayed in the time spectacular and persistent variation trends affecting all the monitored vents. The observed variations, which include a continuous decrease of both N2/He and N2/CO2 ratios since 1985, paralleled by an increase of He/CO2, can not be explained neither with changes in processes of boiling-condensation in the local hydrothermal system nor with changes in the mixing proportions between a magmatic vapour and hydrothermal fluids. Consequently we investigated the possibility that the trends of inert gas species are governed by changes in the conditions controlling magma degassing at depth. We applied a magma degassing model, with the most recent updates for inert gas solubilities, after to have included petrologic constraints from the ranges of melt composition and reservoir pressure at Campi Flegrei. The model simulations for mafic melts (trachybasalt and shoshonite) show a surprising agreement with the measured data. Both decompressive degassing of an ascending magma and mixing between magmatic fluids exsolved at various levels along the ascent path can explain the long-time geochemical changes. Our work highlights that, in caldera systems where the presence of hydrothermal aquifers commonly masks the magmatic signature of reactive

21 CFR 358.510 - Corn and callus remover active ingredients.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Corn and callus remover active ingredients. 358.510 Section 358.510 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... USE Corn and Callus Remover Drug Products § 358.510 Corn and callus remover active ingredients. The...

21 CFR 700.18 - Use of chloroform as an ingredient in cosmetic products.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Use of chloroform as an ingredient in cosmetic... SERVICES (CONTINUED) COSMETICS GENERAL Requirements for Specific Cosmetic Products § 700.18 Use of chloroform as an ingredient in cosmetic products. (a) Chloroform has been used as an ingredient in cosmetic...

Unidentified angular recurrent ulceration responsive to antiviral therapy

Directory of Open Access Journals (Sweden)

Rahmi Amtha

2013-03-01

Full Text Available Background: Recurrent ulcer on angular area is usually called stomatitis angularis. It is caused by many factors such as vertical dimension reduce, vitamin B12, and immune system deficiency, C. albicans and staphylococcus involvement. Clinically is characterized by painful fissure with erythematous base without fever. Purpose: to describe an unidentified angular ulcer proceeded by recurrent ulcers with no response of topical therapy. Case: An 18-years old male came to Oral Medicine clinic in RSCM who complained of angular recurrent ulcers since 3 years ago which developed on skin and bleed easily on mouth opening. Patient had fever before the onset of ulcers. Large, painful, irregular ulcers covered by red crustae on angular area bilaterally. Patient has been treated with various drugs without improvement and lead to mouth opening limitation. Intra oral shows herpetiformtype of ulcer and swollen of gingival. Case management: Provisional diagnosis was established as viral infection thus acyclovir 200 mg five times daily for two weeks and topical anti inflammation gel were administered. Blood test for IgG/IgM of HSV1 and HSV2 were non reactive, however ulceration showed a remarkable improvement. The ulcers healed completely after next 2 weeks with acyclovir. Conclusion: The angular ulceration on above patient failed to fulfill the criteria of stomatitis angularis or herpes labialis lesion. However it showed a good response to antiviral. Therefore, unidentified angular ulceration was appointed, as the lesion might be triggered by other type of human herpes virus or types of virus that response to acyclovir.Latar belakang: ulser rekuren pada sudut mulut biasanya disebut stomatitis angularis. Kelainan ini disebabkan oleh banyak faktor seperti berkurangnya dimensi vertikal, defisiensi vitamin B12 dan sistem kekebalan tubuh, infeksi C. albicans serta staphylococcus. Secara klinis kelainan ini ditandai dengan fisur sakit pada sudut mulut dengan dasar

A Cooking Recipe Recommendation System with Visual Recognition of Food Ingredients

Directory of Open Access Journals (Sweden)

Keiji Yanai

2014-04-01

Full Text Available In this paper, we propose a cooking recipe recommendation system which runs on a consumer smartphone as an interactive mobile application. The proposed system employs real-time visual object recognition of food ingredients, and recommends cooking recipes related to the recognized food ingredients. Because of visual recognition, by only pointing a built-in camera on a smartphone to food ingredients, a user can get to know a related cooking recipes instantly. The objective of the proposed system is to assist people who cook to decide a cooking recipe at grocery stores or at a kitchen. In the current implementation, the system can recognize 30 kinds of food ingredient in 0.15 seconds, and it has achieved the 83.93% recognition rate within the top six candidates. By the user study, we confirmed the effectiveness of the proposed system.

Inerting Aircraft Fuel Systems Using Exhaust Gases

Science.gov (United States)

Hehemann, David G.

2002-01-01

Our purpose in this proposal was to determine the feasibility of using carbon dioxide, possibly obtained from aircraft exhaust gases as a substance to inert the fuel contained in fuel tanks aboard aircraft. To do this, we decided to look at the effects carbon dioxide has upon commercial Jet-A aircraft fuel. In particular, we looked at the solubility of CO2 in Jet-A fuel, the pumpability of CO2-saturated Jet-A fuel, the flashpoint of Jet-A fuel under various mixtures of air and CO2, the static outgassing of CO2-Saturated Jet-A fuel and the dynamic outgassing of Jet-A fuel during pumping of Jet-A fuel.

Ultrasonic Recovery and Modification of Food Ingredients

Science.gov (United States)

Vilkhu, Kamaljit; Manasseh, Richard; Mawson, Raymond; Ashokkumar, Muthupandian

There are two general classes of effects that sound, and ultrasound in particular, can have on a fluid. First, very significant modifications to the nature of food and food ingredients can be due to the phenomena of bubble acoustics and cavitation. The applied sound oscillates bubbles in the fluid, creating intense forces at microscopic scales thus driving chemical changes. Second, the sound itself can cause the fluid to flow vigorously, both on a large scale and on a microscopic scale; furthermore, the sound can cause particles in the fluid to move relative to the fluid. These streaming phenomena can redistribute materials within food and food ingredients at both microscopic and macroscopic scales.

Type of activity and order of experimental conditions affect noise annoyance by identifiable and unidentifiable transportation noise.

Science.gov (United States)

White, Kim; Bronkhorst, Adelbert W; Meeter, Martijn

2018-04-01

Previous studies have shown that identifiability of sound sources influence noise annoyance levels. The aim of the present experiment was to additionally study the effects of actively performing a task versus a less active pastime on noise annoyance. This was done by asking participants to perform a task (task condition) or read a magazine of their choice (no-task condition), while listening to identifiable and unidentifiable samples of transportation noise at varying sound exposure levels (55-85 ASEL). Annoyance was higher for identifiable samples (recordings) than for unidentifiable transformed samples (with equal spectral energy and envelope). Although there was no main effect of activity type on noise annoyance, for the transformed samples, an interaction was found between activity type and sound exposure levels: annoyance started lower in the no-task condition, but rose more steeply with ascending exposure levels than was the case during task performance (large effect). When assessing order effects, it was found that annoyance was higher when the task condition came first, especially for lower sound exposure levels (large effects). It is therefore concluded that the type of activity and the condition order do influence noise annoyance but in interaction with exposure levels, the type of noise and habituation.

Using Akka Platform in Unidentified Falling Object Detection on the LHC.

CERN Document Server

Motesnitsalis, Evangelos

2013-01-01

During my participation in the CERN Summer Student Program 2013, I worked under the Technology Department of CERN and, more specifically, in the Machine Protection and Electrical Integrity (MPE) Group. The MPE Group supports LHC operation and maintains state‐of‐the art technology for magnet circuit protection and interlock systems for the present and future accelerators, magnet test facilities and CERN hosted experiments. Within this context, we developed an application that parallelizes the Unidentified Falling Object Detection Algorithm on the LHC Operational Data Analysis Software. For this reason, we used a JVM-based toolkit, named Akka, which parallelizes the execution by creating a number of actors that run simultaneously. The results of the new approach are presented on the last part of this report. They tend to be quite interesting and promising as we managed to reduce the execution time of the analysis by a factor of 10 on a local machine and the first attempts to execute the program on a cluster...

Modeling the effects of size on patch dynamics of an inert tracer

Directory of Open Access Journals (Sweden)

P. Xiu

2010-03-01

Full Text Available Mesoscale iron enrichment experiments have revealed that additional iron affects the phytoplankton productivity and carbon cycle. However, the role of initial size of fertilized patch in determining the patch evolution is poorly quantified due to the limited observational capability and complex of physical processes. Using a three-dimensional ocean circulation model, we simulated different sizes of inert tracer patches that were only regulated by physical circulation and diffusion. Model results showed that during the first few days since release of inert tracer, the calculated dilution rate was found to be a linear function with time, which was sensitive to the initial patch size with steeper slope for smaller size patch. After the initial phase of rapid decay, the relationship between dilution rate and time became an exponential function, which was also size dependent. Therefore, larger initial size patches can usually last longer and ultimately affect biogeochemical processes much stronger than smaller patches.

Unidentified EGRET sources and their possible Fermi counterparts

International Nuclear Information System (INIS)

Lyapin, A R; Arkhangelskaja, I V; Larin, D S

2017-01-01

Unidentified EGRET sources from 3EG catalog have been analyzed. Preliminary data analysis has shown at least 23 of these sources coincide with those in 3FGL Fermi catalogue within 1, 2 and 3 sigma error intervals of the coordinates and fluxes. Their properties are discussed in the presented work. Even 3-sigma difference allows supposing sources similarity because of more than 3-sigma distinctions in values of fluxes between identified EGRET sources and their Fermi counterparts. For instance, the coincidence between 3EG J1255-0549 and 3FGL J1256.1-0547 was reported in Fermi catalogues 1FGL, 2FGL, 3FGL. However, these sources fluxes (in units of 10 −8 photons × cm −2 × s −1 ) in the energy band E > 100 MeV were 179.7 ± 6.7 (3EG), 44.711 ± 0.724 (3FGL), 53.611 ± 0.997 (2FGL) and 67.939 ± 1.861 (1FGL). Such effect was observed for sufficient portion of identified EGRET sources. It could cause by troubles of particles identification by Fermi/LAT trigger system. Very often charged particles recognized as gamma-quanta because of wrong backsplash analysis. Nevertheless, gammas counts as charged particles due analogous reason and rejected during ground data processing. For example, it appears as geomagnetic modulation presence on gamma-quanta count rate latitudinal profiles in energy band E > 20 MeV. (paper)

[Recent advances of synthetic biology for production of functional ingredients in Chinese materia medica].

Science.gov (United States)

Su, Xin-Yao; Xue, Jian-Ping; Wang, Cai-Xia

2016-11-01

The functional ingredients in Chinese materia medica are the main active substance for traditional Chinese medicine and most of them are secondary metabolites derivatives. Until now,the main method to obtain those functional ingredients is through direct extraction from the Chinese materia medica. However, the income is very low because of the high extraction costs and the decreased medicinal plants. Synthetic biology technology, as a new and microbial approach, can be able to carry out large-scale production of functional ingredients and greatly ease the shortage of traditional Chinese medicine ingredients. This review mainly focused on the recent advances in synthetic biology for the functional ingredients production. Copyright© by the Chinese Pharmaceutical Association.

Safety assessment of personal care products/cosmetics and their ingredients

International Nuclear Information System (INIS)

Nohynek, Gerhard J.; Antignac, Eric; Re, Thomas; Toutain, Herve

2010-01-01

We attempt to review the safety assessment of personal care products (PCP) and ingredients that are representative and pose complex safety issues. PCP are generally applied to human skin and mainly produce local exposure, although skin penetration or use in the oral cavity, on the face, lips, eyes and mucosa may also produce human systemic exposure. In the EU, US and Japan, the safety of PCP is regulated under cosmetic and/or drug regulations. Oxidative hair dyes contain arylamines, the most chemically reactive ingredients of PCP. Although arylamines have an allergic potential, taking into account the high number of consumers exposed, the incidence and prevalence of hair dye allergy appears to be low and stable. A recent (2001) epidemiology study suggested an association of oxidative hair dye use and increased bladder cancer risk in consumers, although this was not confirmed by subsequent or previous epidemiologic investigations. The results of genetic toxicity, carcinogenicity and reproductive toxicity studies suggest that modern hair dyes and their ingredients pose no genotoxic, carcinogenic or reproductive risk. Recent reports suggest that arylamines contained in oxidative hair dyes are N-acetylated in human or mammalian skin resulting in systemic exposure to traces of detoxified, i.e. non-genotoxic, metabolites, whereas human hepatocytes were unable to transform hair dye arylamines to potentially carcinogenic metabolites. An expert panel of the International Agency on Research of Cancer (IARC) concluded that there is no evidence for a causal association of hair dye exposure with an elevated cancer risk in consumers. Ultraviolet filters have important benefits by protecting the consumer against adverse effects of UV radiation; these substances undergo a stringent safety evaluation under current international regulations prior to their marketing. Concerns were also raised about the safety of solid nanoparticles in PCP, mainly TiO 2 and ZnO in sunscreens. However

Safety assessment of personal care products/cosmetics and their ingredients.

Science.gov (United States)

Nohynek, Gerhard J; Antignac, Eric; Re, Thomas; Toutain, Herve

2010-03-01

We attempt to review the safety assessment of personal care products (PCP) and ingredients that are representative and pose complex safety issues. PCP are generally applied to human skin and mainly produce local exposure, although skin penetration or use in the oral cavity, on the face, lips, eyes and mucosa may also produce human systemic exposure. In the EU, US and Japan, the safety of PCP is regulated under cosmetic and/or drug regulations. Oxidative hair dyes contain arylamines, the most chemically reactive ingredients of PCP. Although arylamines have an allergic potential, taking into account the high number of consumers exposed, the incidence and prevalence of hair dye allergy appears to be low and stable. A recent (2001) epidemiology study suggested an association of oxidative hair dye use and increased bladder cancer risk in consumers, although this was not confirmed by subsequent or previous epidemiologic investigations. The results of genetic toxicity, carcinogenicity and reproductive toxicity studies suggest that modern hair dyes and their ingredients pose no genotoxic, carcinogenic or reproductive risk. Recent reports suggest that arylamines contained in oxidative hair dyes are N-acetylated in human or mammalian skin resulting in systemic exposure to traces of detoxified, i.e. non-genotoxic, metabolites, whereas human hepatocytes were unable to transform hair dye arylamines to potentially carcinogenic metabolites. An expert panel of the International Agency on Research of Cancer (IARC) concluded that there is no evidence for a causal association of hair dye exposure with an elevated cancer risk in consumers. Ultraviolet filters have important benefits by protecting the consumer against adverse effects of UV radiation; these substances undergo a stringent safety evaluation under current international regulations prior to their marketing. Concerns were also raised about the safety of solid nanoparticles in PCP, mainly TiO(2) and ZnO in sunscreens. However

Determination of Heritage SSME Pogo Suppressor Resistance and Inertance from Waterflow Pulse Testing

Science.gov (United States)

McDougal, Chris; Eberhart, Chad; Lee, Erik

2016-01-01

Waterflow tests of a heritage Space Shuttle Main Engine pogo suppressor were performed to experimentally quantify the resistance and inertance provided by the suppressor. Measurements of dynamic pressure and flow rate in response to pulsing flow were made throughout the test loop. A unique system identification methodology combined all sensor measurements with a one-dimensional perturbational flow model of the complete water flow loop to spatially translate physical measurements to the device under test. Multiple techniques were then employed to extract the effective resistance and inertance for the pogo suppressor. Parameters such as steady flow rate, perturbational flow rate magnitude, and pulse frequency were investigated to assess their influence on the behavior of the pogo suppressor dynamic response. These results support validation of the RS-25 pogo suppressor performance for use on the Space Launch System Core Stage.

Lipases: particularly effective biocatalysts for cosmetic active ingredients

Directory of Open Access Journals (Sweden)

Yvergnaux Florent

2017-07-01

Full Text Available Enzymes are the tools of choice in the on-going quest for non-pollutant processes to discover molecules for use in skin products. Amongst these biocatalysts, lipases offer considerable potential in terms of ingredient development and are of interest in skin dermocosmetic formulations possessing sensory or biological activities. Lipases have been studied for around thirty years and, in most cases, these enzymes function under what are deemed to be mild conditions, displaying remarkable efficacy particularly in terms of selectivity. This particularly effective strategy will be illustrated through typical synthesis, demonstrating how ester or amide active ingredients are obtained.

Sarcocysts of an unidentified species of Sarcocystis in the sea otter (Enhydra lutris)

Science.gov (United States)

Dubey, J.P.; Lindsay, D.S.; Rosenthal, B.M.; Thomas, N.J.

2003-01-01

The number of Sarcocystis species that infect sea otters (Enhydra lutris) is unknown. Sea otter tissues were recently shown to harbor sarcocysts of S. neurona and of unidentified species of Sarcocystis. Whereas sarcocysts of S. neurona have walls 1a??3 I?m thick with type 9 villar protrusions, ultrastructure of a distinct thin-walled sarcocyst (0.5a??0.7 I?m thick) lacking villar protrusions, but instead exhibiting minute type 1 undulations on the sarcocyst wall, is described in this report. Parasites characterized from a sea otter infection were inferred to be related to, but distinct from, other species belonging to Sarcocystis, based on sequencing and phylogenetic analysis of a portion of the beta subunit of the plastid-encoded RNA polymerase gene.

Performance Specification Shippinpark Pressurized Water Reactor Fuel Drying and Canister Inerting System for PWR Core 2 Blanket Fuel Assemblies Stored within Shippingport Spent Fuel Canisters

International Nuclear Information System (INIS)

JOHNSON, D.M.

2000-01-01

This specification establishes the performance requirements and basic design requirements imposed on the fuel drying and canister inerting system for Shippingport Pressurized Water Reactor (PWR) Core 2 blanket fuel assemblies (BFAs) stored within Shippingport spent fuel (SSFCs) canisters (fuel drying and canister inerting system). This fuel drying and canister inerting system is a component of the U.S. Department of Energy, Richland Operations Office (RL) Spent Nuclear Fuels Project at the Hanford Site. The fuel drying and canister inerting system provides for removing water and establishing an inert environment for Shippingport PWR Core 2 BFAs stored within SSFCs. A policy established by the U.S. Department of Energy (DOE) states that new SNF facilities (this is interpreted to include structures, systems and components) shall achieve nuclear safety equivalence to comparable U.S. Nuclear Regulatory Commission (NRC)-licensed facilities. This will be accomplished in part by applying appropriate NRC requirements for comparable NRC-licensed facilities to the fuel drying and canister inerting system, in addition to applicable DOE regulations and orders

The inert doublet model in the light of Fermi-LAT gamma-ray data: a global fit analysis

Science.gov (United States)

Eiteneuer, Benedikt; Goudelis, Andreas; Heisig, Jan

2017-09-01

We perform a global fit within the inert doublet model taking into account experimental observables from colliders, direct and indirect dark matter searches and theoretical constraints. In particular, we consider recent results from searches for dark matter annihilation-induced gamma-rays in dwarf spheroidal galaxies and relax the assumption that the inert doublet model should account for the entire dark matter in the Universe. We, moreover, study in how far the model is compatible with a possible dark matter explanation of the so-called Galactic center excess. We find two distinct parameter space regions that are consistent with existing constraints and can simultaneously explain the excess: One with dark matter masses near the Higgs resonance and one around 72 GeV where dark matter annihilates predominantly into pairs of virtual electroweak gauge bosons via the four-vertex arising from the inert doublet's kinetic term. We briefly discuss future prospects to probe these scenarios.

The inert doublet model in the light of Fermi-LAT gamma-ray data: a global fit analysis

Energy Technology Data Exchange (ETDEWEB)

Eiteneuer, Benedikt; Heisig, Jan [RWTH Aachen University, Institute for Theoretical Particle Physics and Cosmology, Aachen (Germany); Goudelis, Andreas [UMR 7589 CNRS and UPMC, Laboratoire de Physique Theorique et Hautes Energies (LPTHE), Paris (France)

2017-09-15

We perform a global fit within the inert doublet model taking into account experimental observables from colliders, direct and indirect dark matter searches and theoretical constraints. In particular, we consider recent results from searches for dark matter annihilation-induced gamma-rays in dwarf spheroidal galaxies and relax the assumption that the inert doublet model should account for the entire dark matter in the Universe. We, moreover, study in how far the model is compatible with a possible dark matter explanation of the so-called Galactic center excess. We find two distinct parameter space regions that are consistent with existing constraints and can simultaneously explain the excess: One with dark matter masses near the Higgs resonance and one around 72 GeV where dark matter annihilates predominantly into pairs of virtual electroweak gauge bosons via the four-vertex arising from the inert doublet's kinetic term. We briefly discuss future prospects to probe these scenarios. (orig.)

Ingredients and change processes in occupational therapy for children: a grounded theory study.

Science.gov (United States)

Armitage, Samantha; Swallow, Veronica; Kolehmainen, Niina

2017-05-01

There is limited evidence about the effectiveness of occupational therapy interventions for participation outcomes in children with coordination difficulties. Developing theory about the interventions, i.e. their ingredients and change processes, is the first step to advance the evidence base. To develop theory about the key ingredients of occupational therapy interventions for children with coordination difficulties and the processes through which change in participation might happen. Grounded theory methodology, as described by Kathy Charmaz, was used to develop the theory. Children and parents participated in semi-structured interviews to share their experiences of occupational therapy and processes of change. Data collection and analysis were completed concurrently using constant comparison methods. Five key ingredients of interventions were described: performing activities and tasks; achieving; carer support; helping and supporting the child; and labelling. Ingredients related to participation by changing children's mastery experience, increasing capability beliefs and sense of control. Parents' knowledge, skills, positive emotions, sense of empowerment and capability beliefs also related to children's participation. The results identify intervention ingredients and change pathways within occupational therapy to increase participation. It is unclear how explicitly and often therapists consider and make use of these ingredients and pathway.

Encapsulation of cosmetic active ingredients for topical application--a review.

Science.gov (United States)

Casanova, Francisca; Santos, Lúcia

2016-02-01

Microencapsulation is finding increasing applications in cosmetics and personal care markets. This article provides an overall discussion on encapsulation of cosmetically active ingredients and encapsulation techniques for cosmetic and personal care products for topical applications. Some of the challenges are identified and critical aspects and future perspectives are addressed. Many cosmetics and personal care products contain biologically active substances that require encapsulation for increased stability of the active materials. The topical and transdermal delivery of active cosmetic ingredients requires effective, controlled and safe means of reaching the target site within the skin. Preservation of the active ingredients is also essential during formulation, storage and application of the final cosmetic product. Microencapsulation offers an ideal and unique carrier system for cosmetic active ingredients, as it has the potential to respond to all these requirements. The encapsulated agent can be released by several mechanisms, such as mechanical action, heat, diffusion, pH, biodegradation and dissolution. The selection of the encapsulation technique and shell material depends on the final application of the product, considering physical and chemical stability, concentration, required particle size, release mechanism and manufacturing costs.

Downstream Processability of Crystal Habit-Modified Active Pharmaceutical Ingredient

DEFF Research Database (Denmark)

Pudasaini, Nawin; Upadhyay, Pratik Pankaj; Parker, Christian Richard

2017-01-01

Efficient downstream processing of active pharmaceutical ingredients (APIs) can depend strongly on their particulate properties, such as size and shape distributions. Especially in drug products with high API content, needle-like crystal habit of an API may show compromised flowability and tablet......Efficient downstream processing of active pharmaceutical ingredients (APIs) can depend strongly on their particulate properties, such as size and shape distributions. Especially in drug products with high API content, needle-like crystal habit of an API may show compromised flowability...

Observability of inert scalars at the LHC

Energy Technology Data Exchange (ETDEWEB)

Hashemi, Majid [Shiraz University, Physics Department, College of Sciences, Shiraz (Iran, Islamic Republic of); Najjari, Saereh [University of Warsaw, Faculty of Physics, Warsaw (Poland)

2017-09-15

In this work we investigate the observability of inert doublet model scalars at the LHC operating at the center of mass energy of 14 TeV. The signal production process is pp → AH{sup ±} → ZHW{sup ±}H leading to two different final states of l{sup +}l{sup -}HjjH and l{sup +}l{sup -}Hl{sup ±}νH based on the hadronic and leptonic decay channels of the W boson. All the relevant background processes are considered and an event selection is designed to distinguish the signal from the large Standard Model background. We found that signals of the selected search channels are well observable at the LHC with an integrated luminosity of 300 fb{sup -1}. (orig.)

Collision-induced polarizabilities of inert gas atoms

International Nuclear Information System (INIS)

Clarke, K.L.; Madden, P.A.; Buckingham, A.D.

1978-01-01

The use of polarizability densities to calculate collision-induced polarizabilities is investigated. One method for computing polarizabilities of inert gas diatoms employs atomic polarizability densities from finite-field Hartree-Fock calculations, together with classical equations for the polarization of dielectrics. It is shown that this model gives inaccurate values for both the local fields and the local response to non-uniform fields. An alternative method incorporating the same physical effects is used to compute the pair polarizabilities to first order in the interatomic interaction. To first order the pair contribution to the trace of the polarizability is negative at short range. The calculated anisotropy does not differ significantly from the DID value, whereas the polarizability density calculation gives a substantial reduction in the anisotropy. (author)

A comprehensive evaluation of the toxicology of cigarette ingredients: carbohydrates and natural products.

Science.gov (United States)

Coggins, Christopher R E; Wagner, Karl A; Werley, Michael S; Oldham, Michael J

2011-06-01

Eleven carbohydrates and natural product ingredients were added individually to experimental cigarettes. A battery of tests was used to compare toxicity of mainstream smoke from these experimental cigarettes to matched control cigarettes without test ingredients. Smoke fractions from each cigarette type were evaluated using analytical chemistry; in vitro cytotoxicity (neutral red uptake) and in vitro bacterial (Salmonella) mutagenicity (five strains) testing. For 10 ingredients (β-cyclodextrin, cleargum, D-sorbitol, high fructose corn syrup, honey, invert sugar, maltodextrin, molasses, raisin juice concentrate, and sucrose), 90-day nose-only smoke inhalation studies using rats were also performed. In general, addition of each ingredient in experimental cigarettes resulted in minimal changes in smoke chemistry; the exceptions were D-sorbitol and sucrose, where reductions in amount of 60% to 80% of control values for some smoke constituents were noted. Additionally, each ingredient resulted in small increases in smoke formaldehyde concentrations. Except for a reduction in cytotoxicity by inclusion of maltodextrin and an increase by inclusion of plum juice concentrate, the cytotoxicity and mutagenicity results were unaffected by addition of the other ingredients in experimental cigarettes. There were also very few statistically significant differences within any of the 10 inhalation studies, and when present, the differences were largely sporadic and inconsistent between sexes. The carbohydrates and natural products tested here as ingredients in experimental cigarettes as a class increased formaldehyde, but resulted in minimal toxicological responses, even at high inclusion levels compared with the levels used in commercial cigarette products.

What Is “Natural”? Consumer Responses to Selected Ingredients

Directory of Open Access Journals (Sweden)

Edgar Chambers

2018-04-01

Full Text Available Interest in “natural” food has grown enormously over the last decade. Because the United States government has not set a legal definition for the term “natural”, customers have formed their own sensory perceptions and opinions on what constitutes natural. In this study, we examined 20 ingredients to determine what consumers consider to be natural. Using a national database, 630 consumers were sampled (50% male and 50% female online, and the results were analyzed using percentages and chi-square tests. No ingredient was considered natural by more than 69% of respondents. We found evidence that familiarity may play a major role in consumers’ determination of naturalness. We also found evidence that chemical sounding names and the age of the consumer have an effect on whether an ingredient and potentially a food is considered natural. Interestingly, a preference towards selecting GMO (genetically modified organisms foods had no significant impact on perceptions of natural.

What Is “Natural”? Consumer Responses to Selected Ingredients

Science.gov (United States)

Chambers, Edgar; Castro, Mauricio

2018-01-01

Interest in “natural” food has grown enormously over the last decade. Because the United States government has not set a legal definition for the term “natural”, customers have formed their own sensory perceptions and opinions on what constitutes natural. In this study, we examined 20 ingredients to determine what consumers consider to be natural. Using a national database, 630 consumers were sampled (50% male and 50% female) online, and the results were analyzed using percentages and chi-square tests. No ingredient was considered natural by more than 69% of respondents. We found evidence that familiarity may play a major role in consumers’ determination of naturalness. We also found evidence that chemical sounding names and the age of the consumer have an effect on whether an ingredient and potentially a food is considered natural. Interestingly, a preference towards selecting GMO (genetically modified organisms) foods had no significant impact on perceptions of natural. PMID:29690627

The effect of ingredients in dry dog foods on the risk of gastric dilatation-volvulus in dogs.

Science.gov (United States)

Raghavan, Malathi; Glickman, Nita W; Glickman, Lawrence T

2006-01-01

Using dry dog food label information, the hypothesis was tested that the risk of gastric dilatation-volvulus (GDV) increases with an increasing number of soy and cereal ingredients and a decreasing number of animal-protein ingredients among the first four ingredients. A nested case-control study was conducted with 85 GDV cases and 194 controls consuming a single brand and variety of dry food. Neither an increasing number of animal-protein ingredients (P=0.79) nor an increasing number of soy and cereal ingredients (P=0.83) among the first four ingredients significantly influenced GDV risk. An unexpected finding was that dry foods containing an oil or fat ingredient (e.g., sunflower oil, animal fat) among the first four ingredients were associated with a significant (P=0.01), 2.4-fold increased risk of GDV. These findings suggest that the feeding of dry dog foods that list oils or fats among the first four label ingredients predispose a high-risk dog to GDV.

Effects of Some Topological Ingredients on the Evolutionary Ultimatum Game

International Nuclear Information System (INIS)

Deng Lili; Zhang Jianxiong; Tang Wansheng; Zhang Wei

2012-01-01

This study aims at figuring out the crucial topological ingredients which affect the outcomes of the ultimatum game located on different networks, encompassing the regular network, the random network, the small-world network, and the scale-free network. With the aid of random interchanging algorithm, we investigate the relations between the outcomes of the ultimatum game and some topological ingredients, including the average range, the clustering coefficient and the heterogeneity, and so forth. It is found that for the regular, random and small-work networks, the average range and the clustering coefficient have evident impacts on the ultimatum game, while for the scale-free network, the original degree heterogeneity and the underlying rich-club characterizations are the mainly important topological ingredients that influence the outcomes of ultimatum game substantially.

Development of baked and extruded functional foods from metabolic syndrome specific ingredient mix.

Science.gov (United States)

Miglani, Neetu; Bains, Kiran; Kaur, Harpreet

2015-09-01

The study was aimed to develop baked and extruded functional foods from Metabolic Syndrome (MS) specific designed ingredient mixes with optimum amino acid makeup using key food ingredients with functional properties such as whole cereals, legumes, skimmed milk powder, along with flaxseeds and fenugreek seeds. Two cereals viz. barley and oats and four pulses viz. mung bean, cowpea, bengal gram and soybean were blended in different proportions in order to balance the limiting amino acid lysine in the wheat flour. Three products namely bread, extruded snack and noodles prepared from twenty five ingredient mixes. Six ingredient mixes of breads and four ingredient mixes each of extruded snack and noodles specifically designed for MS patients were organoleptically at par with control wheat flour products. The acceptable products had significantly (p ≤ 0.05) higher lysine, crude protein, ash and fibre and low carbohydrates in compare control whole wheat flour products, hence appropriate for MS patients.

Botanicals and anti-inflammatories: natural ingredients for rosacea.

Science.gov (United States)

Emer, Jason; Waldorf, Heidi; Berson, Diane

2011-09-01

Rosacea is a chronic inflammatory skin condition characterized by cutaneous hypersensitivity. There are many therapeutic options available for the treatment of rosacea, but none are curative. Since the pathogenesis of rosacea remains elusive, it is not surprising that no single treatment is paramount and that many patients find therapies unsatisfactory or even exacerbating. Treatments are prescribed to work in concert with each other in order to ameliorate the common clinical manifestations, which include: papules and pustules, telangiectasias, erythema, gland hypertrophy, and ocular disease. The most validated topical therapies include metronidazole, azelaic acid, and sodium sulfacetamide-sulfur. Many other topical therapies, such as calcineurin inhibitors, benzoyl peroxide, clindamycin, retinoids, topical corticosteroids, and permethrin have demonstrated varying degrees of success. Due to the inconsistent results of the aforementioned therapies patients are increasingly turning to alternative products containing natural ingredients or botanicals to ease inflammation and remit disease. Additional research is needed to elucidate the benefits of these ingredients in the management of rosacea, but some important considerations regarding the natural ingredients with clinical data will be discussed here. Copyright © 2011 Elsevier Inc. All rights reserved.

The use of irradiated ingredients in food processing

International Nuclear Information System (INIS)

Kiss, I.; Zachariev, G.; Farkas, J.; Szabad, J.; Toth-Pesti, K.

1978-01-01

The microbe-count reducing effects of gamma radiation and of ethylene oxide were compared in ground paprika and dried onion flakes. It was established that the commercially applied ethylene oxide gas treatment has the same bactericidal effect (2-3 log cycles reduction of the total viable bacterial count) as a 5kGy radiation dose. However, ethylene oxide treatment of paprika was practically ineffective in relation to the mould count, while irradiation with 5kGy destroyed the moulds very effectively. The colour and pigment content of paprika powder were not diminished by this radiation dose. A dry mixture intended for use in canned luncheon meat was treated with 5kGy. The canned meat product produced with the radiation-decontaminated ingredients was microbiologically stable even when heat-sterilized by a sterilization equivalent of F 0 =1.1. Considering the organoleptic features and microbiological safety, a heat treatment of about F 0 =3 is suggested when using irradiated ingredients. This is about the half of the F 0 value generally proposed for completely stable canned meat products. Besides the saving of energy, a good quality can be achieved by using radiation-decontaminated ingredients. (author)

Defined media and inert supports : their potential as solid-state fermentation production systems

NARCIS (Netherlands)

Ooijkaas, L.P.; Weber, F.J.; Buitelaar, R.M.; Tramper, J.; Rinzema, A.

2000-01-01

Solid-state fermentation (SSF) using inert supports impregnated with chemically defined liquid media has several potential applications in both scientific studies and in the industrial production of high-value products, such as metabolites, biological control agents and enzymes. As a result of its

Nucleosynthesis confronts an unstable inert 17 keV state

International Nuclear Information System (INIS)

Enqvist, K.; Kainulainen, K.; Thomson, M.

1991-01-01

We study the cosmological consequences of an inert 17 keV state mixing with the electron neutrino. We find that the nucleosynthesis upper bound on the primordial helium abundance prohibits the existence of such a state, unless its lifetime falls into the range 6x10 -4 s vac -2 s. In this range the decay occurs after the chemical decoupling of the electron neutrinos and before the beginning of the nucleosynthesis, with the result that the predicted helium abundance can be lower than what it would be in the standard scenario. (orig.)

Re-derived overclosure bound for the inert doublet model

Science.gov (United States)

Biondini, S.; Laine, M.

2017-08-01

We apply a formalism accounting for thermal effects (such as modified Sommerfeld effect; Salpeter correction; decohering scatterings; dissociation of bound states), to one of the simplest WIMP-like dark matter models, associated with an "inert" Higgs doublet. A broad temperature range T ˜ M/20 . . . M/104 is considered, stressing the importance and less-understood nature of late annihilation stages. Even though only weak interactions play a role, we find that resummed real and virtual corrections increase the tree-level overclosure bound by 1 . . . 18%, depending on quartic couplings and mass splittings.

Efficiency of inert mineral dusts in the control of corn weevil

Directory of Open Access Journals (Sweden)

Carlos F. Jairoce

2016-02-01

Full Text Available ABSTRACT Corn weevil (Sitophilus zeamais may cause great losses in the crop and in stored corn grains. This insect is controlled with the use of chemical insecticides, which may cause serious damage to human health. One alternative of control is the use of inert dusts. The objective of this study was to evaluate the efficiency of inert dusts in the control of S. zeamais under laboratory conditions. The experiment was conducted in 2014, in a completely randomized design, and the treatments consisted of basalt dust with three different granulometries (A, B and C and diatomaceous earth, each of which at the doses of 2 and 4 kg t-1 and a control (no application. Each treatment had four replicates, and the sample unit consisted of 20 g of corn grains infected with 10 adults of S. zeamais kept in temperature-controlled chamber at 25 °C, 70% RH and photophase of 12 h. The dust efficiency was calculated using the equation of Abbott. The mortality rate was higher with the use of diatomaceous earth, reaching 100% after 5 days of exposure and the percentage of control for basalt dusts, 29 days after treatment, was above 80%.

Cytotoxic xanthone-anthraquinone heterodimers from an unidentified fungus of the order Hypocreales (MSX 17022).

Science.gov (United States)

Ayers, Sloan; Graf, Tyler N; Adcock, Audrey F; Kroll, David J; Shen, Qi; Swanson, Steven M; Matthew, Susan; Carcache de Blanco, Esperanza J; Wani, Mansukh C; Darveaux, Blaise A; Pearce, Cedric J; Oberlies, Nicholas H

2012-01-01

Two new xanthone-anthraquinone heterodimers, acremoxanthone C (5) and acremoxanthone D (2), have been isolated from an extract of an unidentified fungus of the order Hypocreales (MSX 17022) by bioactivity-directed fractionation as part of a search for anticancer leads from filamentous fungi. Two known related compounds, acremonidin A (4) and acremonidin C (3) were also isolated, as was a known benzophenone, moniliphenone (1). The structures of these isolates were determined via extensive use of spectroscopic and spectrometric tools in conjunction with comparisons to the literature. All compounds (1-5) were evaluated against a suite of biological assays, including those for cytotoxicity, inhibition of the 20S proteasome, mitochondrial transmembrane potential and nuclear factor-κB.

A TALE OF THREE MYSTERIOUS SPECTRAL FEATURES IN CARBON-RICH EVOLVED STARS: THE 21 μm, 30 μm, AND “UNIDENTIFIED INFRARED” EMISSION FEATURES

Energy Technology Data Exchange (ETDEWEB)

Mishra, Ajay; Li, Aigen [Department of Physics and Astronomy, University of Missouri, Columbia, MO 65211 (United States); Jiang, B. W., E-mail: amishra@mail.missouri.edu, E-mail: lia@missouri.edu, E-mail: bjiang@bnu.edu.cn [Department of Astronomy, Beijing Normal University, Beijing 100875 (China)

2015-03-20

The mysterious “21 μm” emission feature seen almost exclusively in the short-lived protoplanetary nebula (PPN) phase of stellar evolution remains unidentified since its discovery two decades ago. This feature is always accompanied by the equally mysterious, unidentified “30 μm” feature and the so-called “unidentified infrared” (UIR) features at 3.3, 6.2, 7.7, 8.6, and 11.3 μm which are generally attributed to polycyclic aromatic hydrocarbon (PAH) molecules. The 30 μm feature is commonly observed in all stages of stellar evolution from the asymptotic giant branch through PPN to the planetary nebula phase. We explore the interrelations among the mysterious 21, 30 μm, and UIR features of the 21 μm sources. We derive the fluxes emitted in the observed UIR, 21, and 30 μm features from published Infrared Space Observatory or Spitzer/IRS spectra. We find that none of these spectral features correlate with each other. This argues against a common carrier (e.g., thiourea) for both the 21 μm feature and the 30 μm feature. This also does not support large PAH clusters as a possible carrier for the 21 μm feature.

Inert materials for the GFR fuel. Characterizations, chemical interactions and irradiation damage

International Nuclear Information System (INIS)

Audubert, Fabienne; Carlot, Gaoelle; Lechelle, Jacques; David, Laurent; Gomes, Severine

2005-01-01

In the framework of an extensive R and D Program on GFR fuel, studies on inert materials have been performed at the French Atomic Energy Commission (CEA). The inert materials would be associated with the fuel with the aim of featuring an efficient barrier to radiotoxic species with regard to the cooling circuit of the reactor. Potential matrices identified for dispersion fuels or particles fuels are SiC, TiN, ZrN, ZrC, TiC. Physical microstructural and thermal properties have been determined in order to evaluate elaboration process effects. The evolution under irradiation of thermal properties (such as conductivity, diffusivity) of the materials has been studied using heavy ions to simulate fission product irradiation. After irradiation, scanning thermal microscopy is used to investigate the thermal degradation of the materials. Thermal conductivity variations were obtained on TiC irradiated with krypton ion at an energy of 86 MeV and a fluence of 5.10 15 ions.cm -2 . They are quantified at 19 W.m -1 .K -1 . On other materials such as SiC, ZrC, TiN, no thermal conductivity contrast was shown. Reactivity between the inert matrix (SiC or TiN) and the fuel (U, Pu)N have been evaluated on powders and on ceramic samples in contact by a thermal treatment under several atmospheres. It was shown that SiC reacts with (U, Pu)N in various atmospheres making secondary phases as PuSi 2 , USi 2 , U 20 Si 16 C 3 . TiN behaviour seems to be better: the only reactivity which may take place would be a variation of the nitrogen stoichiometry in TiN and (U, Pu)N at the interface. (author)

Microencapsulation as a tool for incorporating bioactive ingredients into food.

Science.gov (United States)

Kuang, S S; Oliveira, J C; Crean, A M

2010-11-01

Microencapsulation has been developed by the pharmaceutical industry as a means to control or modify the release of drug substances from drug delivery systems. In drug delivery systems microencapsulation is used to improve the bioavailability of drugs, control drug release kinetics, minimize drug side effects, and mask the bitter taste of drug substances. The application of microencapsulation has been extended to the food industry, typically for controlling the release of flavorings and the production of foods containing functional ingredients (e.g. probiotics and bioactive ingredients). Compared to the pharmaceutical industry, the food industry has lower profit margins and therefore the criteria in selecting a suitable microencapsulation technology are more stringent. The type of microcapsule (reservoir and matrix systems) produced and its resultant release properties are dependent on the microencapsulation technology, in addition to the physicochemical properties of the core and the shell materials. This review discusses the factors that affect the release of bioactive ingredients from microcapsules produced by different microencapsulation technologies. The key criteria in selecting a suitable microencapsulation technology are also discussed. Two of the most common physical microencapsulation technologies used in pharmaceutical processing, fluidized-bed coating, and extrusion-spheronization are explained to highlight how they might be adapted to the microencapsulation of functional bioactive ingredients in the food industry.

Influence of composition and substrate bias on structure and inert-gas content of sputter-deposited Ni-La alloys

International Nuclear Information System (INIS)

Knoll, R.W.; McClanahan, E.D.

1982-09-01

X-ray diffraction patterns show that the disappearance of crystallinity in the deposit occurs gradually as the La content increases. At the same time, the deposit becomes saturated with Kr. Because there is no evidence of crystalline La metal or Ni-La intermetallic phase in the diffraction data, it may be concluded that each La atom creates a highly disordered (amorphous) region in the lattice, and that this region contains interstitial voids large enough to capture inert gas atoms. Saturation of the gas content with respect to La/Ni ratio might commence when these disordered regions begin to impinge upon one another. Finally, if inert gas atoms occupy interstitial voids within the deposit, then determination of the gas trapping characteristics of the material, using inert gas ions of different sizes, may be a means of studying the structure of glassy vapor-deposited materials. For example, the size distribution of the interstitial voids might be determined in this manner

Reducing unidentified MOV failures: An innovative approach to thermal overload monitoring

International Nuclear Information System (INIS)

Hill, K.; Watson, M.E.; Ali, H.S.; Schlesinger, R.

1991-01-01

Historically the failure of motor-operated valves to actuate on demand has caused plant transients, reduced safety system reliability, and lost plant availability. The typical control and indication circuit design uses thermal overload contacts in the control circuit only. This has been recognized as a significant unidentified valve failure mode that may prevent the valve from performing its safety function when required. Different approaches have been evaluated to alert operations personnel to this thermal overload condition, but no cost-effective solution has provided indication of the thermal overload while maintaining valve position indication. Iowa Electric Light and Power Company's Duane Arnold Energy Center (DAEC) is utilizing a nuclear-qualified thermal overload monitor in valve control and indication circuits. This innovative approach has proven economical as no new cabling or indicating devices are required. Indication is provided using existing valve position indicating lights. The monitor is engineered to provide indication of a thermal overload trip as well as continuous indication of valve position, consistent with Regulatory Guide 1.97 and guidance provided by Generic Letter 89-10

21 CFR 720.7 - Notification of person submitting cosmetic product ingredient statement.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Notification of person submitting cosmetic product... AND HUMAN SERVICES (CONTINUED) COSMETICS VOLUNTARY FILING OF COSMETIC PRODUCT INGREDIENT COMPOSITION STATEMENTS § 720.7 Notification of person submitting cosmetic product ingredient statement. When Form FDA...

Fragranced consumer products: Chemicals emitted, ingredients unlisted

International Nuclear Information System (INIS)

Steinemann, Anne C.; MacGregor, Ian C.; Gordon, Sydney M.; Gallagher, Lisa G.; Davis, Amy L.; Ribeiro, Daniel S.; Wallace, Lance A.

2011-01-01

Fragranced consumer products are pervasive in society. Relatively little is known about the composition of these products, due to lack of prior study, complexity of formulations, and limitations and protections on ingredient disclosure in the U.S. We investigated volatile organic compounds (VOCs) emitted from 25 common fragranced consumer products-laundry products, personal care products, cleaning supplies, and air fresheners-using headspace analysis with gas chromatography/mass spectrometry (GC/MS). Our analysis found 133 different VOCs emitted from the 25 products, with an average of 17 VOCs per product. Of these 133 VOCs, 24 are classified as toxic or hazardous under U.S. federal laws, and each product emitted at least one of these compounds. For 'green' products, emissions of these compounds were not significantly different from the other products. Of all VOCs identified across the products, only 1 was listed on any product label, and only 2 were listed on any material safety data sheet (MSDS). While virtually none of the chemicals identified were listed, this nonetheless accords with U.S. regulations, which do not require disclosure of all ingredients in a consumer product, or of any ingredients in a mixture called 'fragrance.' Because the analysis focused on compounds emitted and listed, rather than exposures and effects, it makes no claims regarding possible risks from product use. Results of this study contribute to understanding emissions from common products, and their links with labeling and legislation.

A comprehensive evaluation of the toxicology of cigarette ingredients: heterocyclic nitrogen compounds.

Science.gov (United States)

Coggins, Christopher R E; Merski, Jerome A; Oldham, Michael J

2011-06-01

Three heterocyclic nitrogen compounds, 2,3-diethylpyrazine (DEP), 2,3,5,6-tetramethylpyrazine (TMP), and 2-acetyl pyridine (AP), are naturally present in tobacco and are also added to tobacco as flavor ingredients. A battery of tests was used to compare the toxicity of mainstream smoke from experimental cigarettes containing the three heterocyclic nitrogen compounds added individually at three different levels. The lowest target inclusion level of the ingredient was 10 ppm, and the highest was 10,000 ppm. Smoke from experimental and control cigarettes was evaluated in analytical smoke chemistry, in vitro cytotoxicity, and mutagenicity assays. The cigarettes with added DEP produced some minor (approximately 10%) changes in smoke chemistry when compared with the cigarettes containing no DEP. Smoke chemistry was effectively unchanged by the addition of either AP or TMP. Cytotoxicity, assessed by the neutral red uptake assay using both gas-vapor and particulate phases of smoke, was unaffected by the addition of any of the test ingredients. Mutagenicity, assessed in five strains of Salmonella treated with mainstream cigarette smoke condensate, also was unaffected by any of the test ingredients. Despite the exaggerated ingredient levels relative to commercial-use levels, there was a lack of a toxicological response for the three heterocyclic nitrogen compounds in the test systems used.

Research Gaps in the Use of Dairy Ingredients in Food Aid Products.

Science.gov (United States)

DiRienzo, Douglas

2016-03-01

Nutritional interventions to help prevent stunting, particularly in the first 1000 days from conception to 2 years of a child's life, are a major focus of numerous food aid organizations worldwide. Dairy ingredients can play an important role in enhancing the nutritional value and effectiveness of food products used in food aid. This article addresses gaps in research on malnutrition from both a broad perspective and specific to dairy ingredients. Narrative review. From a broad perspective, there is a need for gaining a consensus by the research community and funders of research on best practices for protocol development, outcomes measured, and reporting of study outcomes. Identification of biomarkers and rapid screening methods and consistent application of their use would expedite future research. A better understanding of nutritional requirements for malnourished populations, including the effects of energy deficits and disease on those requirements, is needed. More specific to dairy ingredients, a key research question is: Does dairy protein or the package of nutrients provided by dairy ingredients have a unique impact on growth, and if so, how? Also, data on the optimal levels of dairy ingredients based on the effective cost of treatment are needed, particularly in the treatment and prevention of moderate acute malnutrition and during pregnancy. © The Author(s) 2016.

Potential Antitumor Effects of Pomegranates and Its Ingredients.

Science.gov (United States)

Rahmani, Arshad H; Alsahli, Mohammed A; Almatroodi, Saleh A

2017-01-01

The treatment based on plant or plant derivatives is a promising strategy in the killing of cancers cells. Moreover, wide-ranging finding has established that medicinal plant and its ingredient modulate several cells signaling pathways or inhibiting the carcinogenesis process. In this vista, pomegranates fruits, seeds and peels illustrate cancer preventive role seems to be due to rich source of antioxidant and other valuable ingredients. Furthermore, anti-tumour activities of pomegranates have been evidences through the modulation of cell signaling pathways including transcription factor, apoptosis and angiogenesis. In this review article, anti-tumor activity of pomegranates and its components or its different type of extracts are described to understand the mechanism of action of pomegranates in cancer therapy.

Multiple inert gas elimination technique by micropore membrane inlet mass spectrometry--a comparison with reference gas chromatography.

Science.gov (United States)

Kretzschmar, Moritz; Schilling, Thomas; Vogt, Andreas; Rothen, Hans Ulrich; Borges, João Batista; Hachenberg, Thomas; Larsson, Anders; Baumgardner, James E; Hedenstierna, Göran

2013-10-15

The mismatching of alveolar ventilation and perfusion (VA/Q) is the major determinant of impaired gas exchange. The gold standard for measuring VA/Q distributions is based on measurements of the elimination and retention of infused inert gases. Conventional multiple inert gas elimination technique (MIGET) uses gas chromatography (GC) to measure the inert gas partial pressures, which requires tonometry of blood samples with a gas that can then be injected into the chromatograph. The method is laborious and requires meticulous care. A new technique based on micropore membrane inlet mass spectrometry (MMIMS) facilitates the handling of blood and gas samples and provides nearly real-time analysis. In this study we compared MIGET by GC and MMIMS in 10 piglets: 1) 3 with healthy lungs; 2) 4 with oleic acid injury; and 3) 3 with isolated left lower lobe ventilation. The different protocols ensured a large range of normal and abnormal VA/Q distributions. Eight inert gases (SF6, krypton, ethane, cyclopropane, desflurane, enflurane, diethyl ether, and acetone) were infused; six of these gases were measured with MMIMS, and six were measured with GC. We found close agreement of retention and excretion of the gases and the constructed VA/Q distributions between GC and MMIMS, and predicted PaO2 from both methods compared well with measured PaO2. VA/Q by GC produced more widely dispersed modes than MMIMS, explained in part by differences in the algorithms used to calculate VA/Q distributions. In conclusion, MMIMS enables faster measurement of VA/Q, is less demanding than GC, and produces comparable results.

Insights on in vitro models for safety and toxicity assessment of cosmetic ingredients.

Science.gov (United States)

Almeida, Andreia; Sarmento, Bruno; Rodrigues, Francisca

2017-03-15

According to the current European legislation, the safety assessment of each individual cosmetic ingredient of any formulation is the basis for the safety evaluation of a cosmetic product. Also, animal testing in the European Union is prohibited for cosmetic ingredients and products since 2004 and 2009, respectively. Additionally, the commercialization of any cosmetic products containing ingredients tested on animal models was forbidden in 2009. In consequence of these boundaries, the European Centre for the Validation of Alternative Methods (ECVAM) proposes a list of validated cell-based in vitro models for predicting the safety and toxicity of cosmetic ingredients. These models have been demonstrated as valuable and effective tools to overcome the limitations of animal in vivo studies. Although the use of in vitro cell-based models for the evaluation of absorption and permeability of cosmetic ingredients is widespread, a detailed study on the properties of these platforms and the in vitro-in vivo correlation compared with human data are required. Moreover, additional efforts must be taken to develop in vitro models to predict carcinogenicity, repeat dose toxicity and reproductive toxicity, for which no alternative in vitro methods are currently available. This review paper summarizes and characterizes the most relevant in vitro models validated by ECVAM employed to predict the safety and toxicology of cosmetic ingredients. Copyright © 2017 Elsevier B.V. All rights reserved.

Radiation decontamination of dry food ingredients and processing aids

Energy Technology Data Exchange (ETDEWEB)

Farkas, J

1984-01-01

Radiation decontamination of dry ingredients, herbs and enzyme preparations is a technically feasible, economically viable and safe physical process. The procedure is direct, simple, requires no additives and is highly efficient. Its dose requirement is moderate. Radiation doses of 3-10 kGy (0.3-1 mrad) have proved sufficient to reduce the viable counts to a satisfactory level. Ionising radiations do not cause any significant rise in temperature. The flavour, texture or other important technological or sensory properties of most ingredients are not influenced at radiation doses necessary for satisfactory decontamination, and radiation obviates the chemical residue problem. The microflora surviving radiation decontamination of dry ingredients are more susceptible to subsequent antimicrobial treatments. Recontamination can be prevented as the product can be irradiated in its final packaging. Irradiation could be carried out in commercial containers and would result in considerable savings of energy and labour as compared to alternative decontamination techniques. Radiation processing of these commodities is an established technology in several countries and more clearances on irradiated foods are expected to be granted in the near future.

Top 10 botanical ingredients in 2010 anti-aging creams.

Science.gov (United States)

Cronin, Hyland; Draelos, Zoe Diana

2010-09-01

New developments in the realm of skin rejuvenation such as phytotherapy are at an astounding increasing pace in the cosmeceutical market. Yet, many of these products that are classified as cosmeceuticals are tested less vigorously and do not have to be approved by the Food and Drug Administration to establish efficacy and safety. Thus, as clinicians, we must ask the question, "Is there science-based evidence to validate the mechanism of these new treatments?" We assessed the top anti-aging creams currently on the market specifically evaluating their botanical ingredients. Some of the most common botanicals that are hot off the market are: Rosmarinus officinalis, Vitis vinifera (grape seed extract), Citronellol, Limonene, Oenothera biennis (evening primrose), Glycyrrhiza glabra (licorice extract), Aframomum angustifolium seed extract, Diosgenin (wild yam), N6 furfuryladenine (kinetin), and Ergothioneine. Through researching each of these botanical ingredients, we have concluded that randomized controlled trials are still needed in this area, but there is promise in some of these ingredients and science to validate them. © 2010 Wiley Periodicals, Inc.

Separation of Nuclear Fuel Surrogates from Silicon Carbide Inert Matrix

International Nuclear Information System (INIS)

Baney, Ronald

2008-01-01

The objective of this project has been to identify a process for separating transuranic species from silicon carbide (SiC). Silicon carbide has become one of the prime candidates for the matrix in inert matrix fuels, (IMF) being designed to reduce plutonium inventories and the long half-lives actinides through transmutation since complete reaction is not practical it become necessary to separate the non-transmuted materials from the silicon carbide matrix for ultimate reprocessing. This work reports a method for that required process

Triheterometallic Lanthanide Complexes Prepared from Kinetically Inert Lanthanide Building Blocks

DEFF Research Database (Denmark)

Sørensen, Thomas Just; Tropiano, Manuel; Kenwright, Alan M.

2017-01-01

Three molecular structures, each containing three different lanthanide(III) centres, have been prepared by coupling three kinetically inert lanthanide(III) complexes in an Ugi reaction. These 2 kDa molecules were purified by dialysis and characterised by NMR and luminescence techniques. The photo...... and lanthanide(III) centres in these molecules inhibits the efficient sensitisation of europium. We conclude that the intramolecular collisions required for efficient Dexter energy transfer from the sensitiser to the lanthanide(III) centre can be prevented by steric congestion....

Small-Scale Shock Testing of Propellants and Ingredients

National Research Council Canada - National Science Library

Dawley, S

2004-01-01

.... The use of small-scale gap testing to evaluate the shock sensitivity of individual propellant ingredients and propellant formulations is a valuable method for experimentally establishing shock...

Molecular ingredients of heterogeneous catalysis

International Nuclear Information System (INIS)

Somorjai, G.A.

1982-06-01

The purpose of this paper is to present a review and status report to those in theoretical chemistry of the rapidly developing surface science of heterogeneous catalysis. The art of catalysis is developing into science. This profound change provides one with opportunities not only to understand the molecular ingredients of important catalytic systems but also to develop new and improved catalyst. The participation of theorists to find answers to important questions is sorely needed for the sound development of the field. It is the authors hope that some of the outstanding problems of heterogeneous catalysis that are identified in this paper will be investigated. For this purpose the paper is divided into several sections. The brief Introduction to the methodology and recent results of the surface science of heterogeneous catalysis is followed by a review of the concepts of heterogeneous catalysis. Then, the experimental results that identified the three molecular ingredients of catalysis, structure, carbonaceous deposit and the oxidation state of surface atoms are described. Each section is closed with a summary and a list of problems that require theoretical and experimental scrutiny. Finally attempts to build new catalyst systems and the theoretical and experimental problems that appeared in the course of this research are described

Molecular ingredients of heterogeneous catalysis

Energy Technology Data Exchange (ETDEWEB)

Somorjai, G.A.

1982-06-01

The purpose of this paper is to present a review and status report to those in theoretical chemistry of the rapidly developing surface science of heterogeneous catalysis. The art of catalysis is developing into science. This profound change provides one with opportunities not only to understand the molecular ingredients of important catalytic systems but also to develop new and improved catalyst. The participation of theorists to find answers to important questions is sorely needed for the sound development of the field. It is the authors hope that some of the outstanding problems of heterogeneous catalysis that are identified in this paper will be investigated. For this purpose the paper is divided into several sections. The brief Introduction to the methodology and recent results of the surface science of heterogeneous catalysis is followed by a review of the concepts of heterogeneous catalysis. Then, the experimental results that identified the three molecular ingredients of catalysis, structure, carbonaceous deposit and the oxidation state of surface atoms are described. Each section is closed with a summary and a list of problems that require theoretical and experimental scrutiny. Finally attempts to build new catalyst systems and the theoretical and experimental problems that appeared in the course of this research are described.

New feed ingredients: the insect opportunity.

Science.gov (United States)

van Raamsdonk, L W D; van der Fels-Klerx, H J; de Jong, J

2017-08-01

In the framework of sustainability and a circular economy, new ingredients for feed are desired and, to this end, initiatives for implementing such novel ingredients have been started. The initiatives include a range of different sources, of which insects are of particular interest. Within the European Union, generally, a new feed ingredient should comply with legal constraints in terms of 'yes, provided that' its safety commits to a range of legal limits for heavy metals, mycotoxins, pesticides, contaminants, pathogens etc. In the case of animal proteins, however, a second legal framework applies which is based on the principle 'no, unless'. This legislation for eradicating transmissible spongiform encephalopathy consists of prohibitions with a set of derogations applying to specific situations. Insects are currently considered animal proteins. The use of insect proteins is a good case to illustrate this difference between a positive, although restricted, modus and a negative modus for allowing animal proteins. This overview presents aspects in the areas of legislation, feed safety, environmental issues, efficiency and detection of the identity of insects. Use of insects as an extra step in the feed production chain costs extra energy and this results in a higher footprint. A measure for energy conversion should be used to facilitate the comparison between production systems based on cold- versus warm-blooded animals. Added value can be found by applying new commodities for rearing, including but not limited to category 2 animal by-products, catering and household waste including meat, and manure. Furthermore, monitoring of a correct use of insects is one possible approach for label control, traceability and prevention of fraud. The link between legislation and enforcement is strong. A principle called WISE (Witful, Indicative, Societal demands, Enforceable) is launched for governing the relationship between the above-mentioned aspects.

Unidentified Factors in Jojoba Meal Prevent Oviduct Development in Broiler Breeder Females.

Science.gov (United States)

Vermaut; Onagbesan; Bruggeman; Verhoeven; Berghman; Flo; Cokelaere; Decuypere

1998-01-19

Supplementation of feed with jojoba meal, as a means for autonomous feed restriction, was successful in depressing feed intake and controlling body weight of broiler breeder pullets to the extent recommended by the breeder company. However, these broiler breeders never produced eggs. At the level of ovary, normal follicle development and maturation did occur. A considerable number of ovulations occurred which were not followed by oviposition. After ovulation, the ova could not be captured by the oviduct, because of the small size of the oviduct, resulting in "internal laying". The virtual absence of oviduct development cannot be explained presently but it must be due to some yet unidentified factor(s) in jojoba meal which prevent(s) the normal development of the oviduct. These factors may be acting by abnormally increasing plasma progesterone or triiodothyronin levels and/or directly by themselves interfering with oviduct development. The nature of these factors requires further investigations.

Electrolytic 99TcO4- reduction at inert electrodes

International Nuclear Information System (INIS)

Kremer, C.; Gambino, D.; Leon, A.; Kremer, E.

1990-01-01

Electrolytic pertechnetate reduction at inert electrodes was studied as an alternative procedure for synthesizing Tc complexes. Pertechnetate reduction was carried out in aqueous media using different aminated ligands (en, dien, trien and 1,3-dap) forming [TcO 2 (amine) 2 ] + type complexes. Simultaneously with synthesis of the desired Tc complex, TcO 2 was electrodeposited onto the cathode. Conversion of TcO 4 - to Tc complex and TcO 2 was studied as a function of several variables (kind and concentration of supporting electrolyte, ligand concentration, pH, current and electrolysis time). (author) 9 refs.; 6 figs.; 1 tab

Impact of airway gas exchange on the multiple inert gas elimination technique: theory.

Science.gov (United States)

Anderson, Joseph C; Hlastala, Michael P

2010-03-01

The multiple inert gas elimination technique (MIGET) provides a method for estimating alveolar gas exchange efficiency. Six soluble inert gases are infused into a peripheral vein. Measurements of these gases in breath, arterial blood, and venous blood are interpreted using a mathematical model of alveolar gas exchange (MIGET model) that neglects airway gas exchange. A mathematical model describing airway and alveolar gas exchange predicts that two of these gases, ether and acetone, exchange primarily within the airways. To determine the effect of airway gas exchange on the MIGET, we selected two additional gases, toluene and m-dichlorobenzene, that have the same blood solubility as ether and acetone and minimize airway gas exchange via their low water solubility. The airway-alveolar gas exchange model simulated the exchange of toluene, m-dichlorobenzene, and the six MIGET gases under multiple conditions of alveolar ventilation-to-perfusion, VA/Q, heterogeneity. We increased the importance of airway gas exchange by changing bronchial blood flow, Qbr. From these simulations, we calculated the excretion and retention of the eight inert gases and divided the results into two groups: (1) the standard MIGET gases which included acetone and ether and (2) the modified MIGET gases which included toluene and m-dichlorobenzene. The MIGET mathematical model predicted distributions of ventilation and perfusion for each grouping of gases and multiple perturbations of VA/Q and Qbr. Using the modified MIGET gases, MIGET predicted a smaller dead space fraction, greater mean VA, greater log(SDVA), and more closely matched the imposed VA distribution than that using the standard MIGET gases. Perfusion distributions were relatively unaffected.

Home cooking and ingredient synergism improve lycopene isomer production in Sofrito.

Science.gov (United States)

Rinaldi de Alvarenga, José Fernando; Tran, Camilla; Hurtado-Barroso, Sara; Martinez-Huélamo, Miriam; Illan, Montserrat; Lamuela-Raventos, Rosa M

2017-09-01

There has been increasing interest in tomato products rich in lycopene Z-isomers since these carotenoids present greater bioavailability and antioxidant capacity than the all-E lycopene form. Intrinsic food properties as well as processing and the interaction between dietary components can all influence the content, type and bioavailability of carotenoids. The aim of this study was to evaluate whether carotenoid content and isomerization in tomato-based Mediterranean sofrito is affected by the process of home cooking and the presence of other ingredients such as extra virgin olive oil, onion and garlic. We used a full factorial design to clarify the contribution of each ingredient to the carotenoid composition of sofrito and to determine whether this can be improved by the cooking time and ingredient synergism. Cooking time and onion content were associated with a higher production of 5-Z-lycopene, 9-Z-lycopene and 13-Z-lycopene in sofrito. Onion proved to be the most interesting ingredient in the sofrito formulation due to their enhancing effect on lycopene isomerization. The use of onion combined with an adequate processing time may improve the bioavailability of lycopene in tomato products. Copyright © 2017 Elsevier Ltd. All rights reserved.

Natural personal care products-analysis of ingredient lists and legal situation.

Science.gov (United States)

Klaschka, Ursula

2016-01-01

Many natural substances are classified as dangerous substances according to the European regulation on classification and labelling. Are they used in natural personal care products today? One hundred ingredient lists were analyzed to find this out. All products with natural substances contained dangerous natural substances or they contained natural substances, for which the information about their classification as dangerous substances is not available. 54 natural substances quoted in the ingredient lists were found to be classified, with 37 substances being classified due to hazardous effects for skin and eyes. However, the most frequently used natural substances are not classified as dangerous. Natural substances are multi-constituent compounds, leading to two main problems in personal care products: the potential interactions of a multitude of substances and the fact that dangerous constituents are not disclosed in the ingredient lists. For example, the fragrance allergens citral, farnesol, limonene, and linalool are frequent components of the natural substances employed. In addition, 82 products listed allergenic fragrance ingredients as single substances in their ingredient lists. Recommendations for sensitive skin in a product's name do not imply that the '26 fragrance allergens' are omitted. Furthermore, 80 products listed 'parfum'/'aroma', and 50 products listed ethanol. The data show that the loopholes for natural substances and for personal care products in the present European chemical legislation (e.g. the exception for classification and labelling of cosmetic products and the exception for information transfer in the supply chain) are not in line with an adequate consumer and environmental protection.

[Study on the ingredients of reserpine by TLC-FT-SERS].

Science.gov (United States)

Wang, Y; Zi, F; Wang, Y; Zhao, Y; Zhang, X; Weng, S

1999-12-01

A new method for analysing the ingredients of reserpine by thin layer chromatography (TLC) and surface-enhanced Raman spectroscopy (SERS) is reported in this paper. The results show that the characteristic spectral bands of reserpine satuated at the thin layer with the amount of sample about 2 microg were obtained. The difference between SERS and solid spectra was found. An absorption model of reserpine and silver sol was proposed. This method can be used to analyse the chemical ingredients with high sensitivity.

Overview of Food Ingredients, Additives and Colors

Science.gov (United States)

... In addition to maintaining the quality of the food, they help control contamination that can cause foodborne illness, including life-threatening ... still be considered safe. Regulations known as Good Manufacturing ... limit the amount of food ingredients used in foods to the amount necessary ...

Water fog inerting of hydrogen-air mixtures

International Nuclear Information System (INIS)

Zalosh, R.G.; Bajpai, S.N.

1982-01-01

Laboratory tests have been conducted to determine the effects of water fog density, droplet diameter and temperature on the lower flammable limit (LFL) of hydrogen-air-steam mixtures. Five different fog nozzles were used to generate dense fogs with volume mean drop diameters ranging from 20 micro-meters to 115 micro-meters. At 20 0 C, these nozzles marginally raised the hydrogen LFL from 4.0 vol.% hydrogen to typically 4.8%, with one exceptional nozzle producing an LFL of 7.2%. At 50 0 C, the LFL in the presence of dense fog ranged from 5.0 to 7.9%, while at 70 0 C, the range was 5.9 to 8.5%. Fog densities required to achieve a given level of partial inerting increased with approximately the second power of average drop diameter, as predicted by a theoretical flame quenching analysis

An analysis of chemical ingredients network of Chinese herbal formulae for the treatment of coronary heart disease.

Directory of Open Access Journals (Sweden)

Fan Ding

Full Text Available As a complex system, the complicated interactions between chemical ingredients, as well as the potential rules of interactive associations among chemical ingredients of traditional Chinese herbal formulae are not yet fully understood by modern science. On the other hand, network analysis is emerging as a powerful approach focusing on processing complex interactive data. By employing network approach in selected Chinese herbal formulae for the treatment of coronary heart disease (CHD, this article aims to construct and analyze chemical ingredients network of herbal formulae, and provide candidate herbs, chemical constituents, and ingredient groups for further investigation. As a result, chemical ingredients network composed of 1588 ingredients from 36 herbs used in 8 core formulae for the treatment of CHD was produced based on combination associations in herbal formulae. In this network, 9 communities with relative dense internal connections are significantly associated with 14 kinds of chemical structures with P<0.001. Moreover, chemical structural fingerprints of network communities were detected, while specific centralities of chemical ingredients indicating different levels of importance in the network were also measured. Finally, several distinct herbs, chemical ingredients, and ingredient groups with essential position in the network or high centrality value are recommended for further pharmacology study in the context of new drug development.

Final report on the safety assessment of Cocos nucifera (coconut) oil and related ingredients.

Science.gov (United States)

Burnett, Christina L; Bergfeld, Wilma F; Belsito, Donald V; Klaassen, Curtis D; Marks, James G; Shank, Ronald C; Slaga, Thomas J; Snyder, Paul W; Andersen, F Alan

2011-05-01

Cocos nucifera (coconut) oil, oil from the dried coconut fruit, is composed of 90% saturated triglycerides. It may function as a fragrance ingredient, hair conditioning agent, or skin-conditioning agent and is reported in 626 cosmetics at concentrations from 0.0001% to 70%. The related ingredients covered in this assessment are fatty acids, and their hydrogenated forms, corresponding fatty alcohols, simple esters, and inorganic and sulfated salts of coconut oil. The salts and esters are expected to have similar toxicological profiles as the oil, its hydrogenated forms, and its constituent fatty acids. Coconut oil and related ingredients are safe as cosmetic ingredients in the practices of use and concentration described in this safety assessment.

[TLC-FT-SERS study on ingredients of Isrhynchophylline].

Science.gov (United States)

Wang, Yuan; Wang, Song-ying; Zhao, Yi-xue; Ren, Gui-fen; Zi, Feng-lan

2002-02-01

A new method for analysing the ingredients of Isrhynchophylline in Uncaria Rhynchophylla Jacks by thin layer chromatography (TLC) and the surface-enhanced Raman spectroscopy (SERS) is reported in this paper. The results show that the characteristic spectra bands of Isrhynchophylline situated at the thin layer with the amount of sample about 2.5 micrograms were obtained. The difference between SERS and solid spectra was found. Great enhancement of the 1,615 cm-1 spectral band was abstained. Molecule was absorbed in surface silver sol by pi electrons in phenyl and by pair of electrons in N together. An absorption model of Isrhynchophylline and silver sol was proposed. This method can be used to analyse the chemical ingredients with high sensitivity.

Encapsulation of health-promoting ingredients: applications in foodstuffs.

Science.gov (United States)

Tolve, Roberta; Galgano, Fernanda; Caruso, Marisa Carmela; Tchuenbou-Magaia, Fideline Laure; Condelli, Nicola; Favati, Fabio; Zhang, Zhibing

2016-12-01

Many nutritional experts and food scientists are interested in developing functional foods containing bioactive agents and many of these health-promoting ingredients may benefit from nano/micro-encapsulation technology. Encapsulation has been proven useful to improve the physical and the chemical stability of bioactive agents, as well as their bioavailability and efficacy, enabling their incorporation into a wide range of formulations aimed to functional food production. There are several reviews concerning nano/micro-encapsulation techniques, but none are focused on the incorporation of the bioactive agents into food matrices. The aim of this paper was to investigate the development of microencapsulated food, taking into account the different bioactive ingredients, the variety of processes, techniques and coating materials that can be used for this purpose.

Report on the treatability study for inerting small quantities of radioactive explosives and explosive components

International Nuclear Information System (INIS)

Loyola, V.M.; Reber, S.D.

1996-02-01

As a result of Sandia's radiation hardening testing on a variety of its explosive components, radioactive waste streams were generated and have to be disposed of as radioactive waste. Due to the combined hazards of explosives and radioactivity, Sandia's Radioactive and Mixed Waste Management organization did not have a mechanism for disposal of these waste streams. This report documents the study done to provide a method for the removal of the explosive hazard from those waste streams. The report includes the design of the equipment used, procedures followed, results from waste stream analog tests and the results from the actual explosive inerting tests on radioactive samples. As a result of the inerting treatment, the waste streams were rendered non-explosive and, thus, manageable through normal radioactive waste disposal channels

Digital breast tomosynthesis (DBT) to characterize MRI-detected additional lesions unidentified at targeted ultrasound in newly diagnosed breast cancer patients

International Nuclear Information System (INIS)

Mariscotti, Giovanna; Durando, Manuela; Regini, Elisa; Fornari, Alberto; Fonio, Paolo; Gandini, Giovanni; Houssami, Nehmat; Campanino, Pier Paolo; Bussone, Riccardo; Castellano, Isabella; Sapino, Anna

2015-01-01

Preoperative breast magnetic resonance (MR) often generates additional suspicious findings needing further investigations. Targeted breast ultrasound (US) is the standard tool to characterize MR additional lesions. The purpose of this study is to evaluate the potential role of digital breast tomosynthesis (DBT) to characterize MR detected additional findings, unidentified at targeted breast US. This prospective study included women who a) had biopsy-proven, newly diagnosed breast cancers detected at conventional 2D mammography and/or US, referred to breast MR for tumour staging; and b) had DBT if additional MR findings were not detected at targeted ('second look') US. In 520 patients, MR identified 164 (in 114 women, 22 %) additional enhancing lesions. Targeted US identified 114/164 (69.5 %) of these, whereas 50/164 (30.5 %) remained unidentified. DBT identified 32/50 of these cases, increasing the overall characterization of MR detected additional findings to 89.0 % (146/164). Using DBT the identified lesions were significantly more likely to be malignant than benign MR-detected additional lesions (p = 0.04). DBT improves the characterization of additional MR findings not identified at targeted breast US in preoperative breast cancer staging. (orig.)

Digital breast tomosynthesis (DBT) to characterize MRI-detected additional lesions unidentified at targeted ultrasound in newly diagnosed breast cancer patients

Energy Technology Data Exchange (ETDEWEB)

Mariscotti, Giovanna; Durando, Manuela; Regini, Elisa; Fornari, Alberto; Fonio, Paolo; Gandini, Giovanni [Breast Imaging Service, Radiology - University of Turin, Department of Diagnostic Imaging and Radiotherapy, A.O.U. Citta della Salute e della Scienza, Torino (Italy); Houssami, Nehmat [University of Sydney, Screening and Test Evaluation Program, School of Public Health, Sydney Medical School, Sydney, NSW (Australia); Campanino, Pier Paolo [Ospedale Koelliker, Breast Imaging Service, Torino (Italy); Bussone, Riccardo [A.O.U. Citta della Salute e della Scienza of Turin, SSCVD Breast Surgery. Department of Surgery, Torino (Italy); Castellano, Isabella; Sapino, Anna [University of Turin, Department of Biomedical Sciences and Human Oncology, A.O.U. Citta della Salute e della Scienza, Torino (Italy)

2015-09-15

Preoperative breast magnetic resonance (MR) often generates additional suspicious findings needing further investigations. Targeted breast ultrasound (US) is the standard tool to characterize MR additional lesions. The purpose of this study is to evaluate the potential role of digital breast tomosynthesis (DBT) to characterize MR detected additional findings, unidentified at targeted breast US. This prospective study included women who a) had biopsy-proven, newly diagnosed breast cancers detected at conventional 2D mammography and/or US, referred to breast MR for tumour staging; and b) had DBT if additional MR findings were not detected at targeted ('second look') US. In 520 patients, MR identified 164 (in 114 women, 22 %) additional enhancing lesions. Targeted US identified 114/164 (69.5 %) of these, whereas 50/164 (30.5 %) remained unidentified. DBT identified 32/50 of these cases, increasing the overall characterization of MR detected additional findings to 89.0 % (146/164). Using DBT the identified lesions were significantly more likely to be malignant than benign MR-detected additional lesions (p = 0.04). DBT improves the characterization of additional MR findings not identified at targeted breast US in preoperative breast cancer staging. (orig.)

Encapsulation and delivery of food ingredients using starch based systems.

Science.gov (United States)

Zhu, Fan

2017-08-15

Functional ingredients can be encapsulated by various wall materials for controlled release in food and digestion systems. Starch, as one of the most abundant natural carbohydrate polymers, is non-allergenic, GRAS, and cheap. There has been increasing interest of using starch in native and modified forms to encapsulate food ingredients such as flavours, lipids, polyphenols, carotenoids, vitamins, enzymes, and probiotics. Starches from various botanical sources in granular or amorphous forms are modified by chemical, physical, and/or enzymatic means to obtain the desired properties for targeted encapsulation. Other wall materials are also employed in combination with starch to facilitate some types of encapsulation. Various methods of crafting the starch-based encapsulation such as electrospinning, spray drying, antisolvent, amylose inclusion complexation, and nano-emulsification are introduced in this mini-review. The physicochemical and structural properties of the particles are described. The encapsulation systems can positively influence the controlled release of food ingredients in food and nutritional applications. Copyright © 2017 Elsevier Ltd. All rights reserved.

Escoabilidade de leitos de partículas inertes com polpa de frutas tropicais: efeitos na secagem em leito de jorro Flowability of inert particle beds with fruit pulp: effects on the drying in spouted bed

Directory of Open Access Journals (Sweden)

Maria de F. D. de Medeiros

2001-12-01

Full Text Available Neste trabalho, foram caracterizados seis tipos de material inerte, utilizados na secagem de polpa de frutas em leito de jorro. Determinou-se o ângulo de repouso das partículas, com e sem adição de água e de polpa de diversas frutas tropicais. Correlacionou-se a escoabilidade com as propriedades das partículas e com a composição química das polpas. Analisou-se a influência do ângulo de repouso sobre o desempenho do secador, no que se refere à produção. Os resultados mostraram que, em geral, as polpas com elevadas concentrações de gordura e sólidos insolúveis e baixos teores de açúcares redutores, facilitam a escoabilidade. Uma análise dos resultados obtidos na secagem de polpa de frutas tropicais, utilizando-se partículas de poliestireno de baixa densidade, como material inerte, mostrou que, embora a escoabilidade permita a obtenção de menores vazões de jorro mínimo, em relação ao desempenho do secador, pode não favorecer uma produção maior de pó.In this work six types of inert particles were characterized and analyzed for drying tropical fruit pulps. The repose angle was determined with and without the addition of water and pulp of various tropical fruits. The bed flowability was related to the particle properties and chemical composition of pulps. The influence of the repose angle on the drying performance was analyzed. It was also verified that the composition of pulps influenced the bed flowability. The global analysis showed that the pulps with high lipids and insoluble solids content and low reducing sugar content improved the bed flowability. The results obtained with the drying of the fruit pulps using low-density polystyrene granules as inert particles showed that high flowabilities lead to lower minimum spout flow rates, but do not necessarily lead to the highest powder production.

Actinide transmutation using inert matrix fuels versus recycle in a low conversion fast burner reactor

Energy Technology Data Exchange (ETDEWEB)

Deinert, M.R.; Schneider, E.A.; Recktenwald, G.; Cady, K.B. [The Department of Mechanical Engineering, The University of Texas at Austin, 1 University Station, C2200, Austin, 78712 (United States)

2009-06-15

Reducing the disposal burden of the long lived radioisotopes that are contained within spent uranium oxide fuel is essential for ensuring the sustainability of nuclear power. Because of their non-fertile matrices, inert matrix fuels (IMFs) could allow light-water reactors to achieve a significant burn down of plutonium and minor actinides that are that are currently produced as a byproduct of operating light-water reactors. However, the extent to which this is possible is not yet fully understood. We consider a ZrO{sub 2} based IMF with a high transuranic loading and show that the neutron fluence (and the subsequent fuel residence time required to achieve it) present a practical limit for the achievable actinide burnup. The accumulation of transuranics in spent uranium oxide fuel is a major obstacle for the sustainability of nuclear power. While commercial light-water reactors (LWR's) produce these isotopes, they can be used to transmute them. At present, the only viable option for doing this is to partly fuel reactors with mixed oxide fuel (MOX) made using recycled plutonium. However, because of parasitic neutron capture in the uranium matrix of MOX, considerable plutonium and minor actinides are also bred as the fuel is burned. A better option is to entrain the recycled isotopes in a non-fertile matrix such as ZrO{sub 2}. Inert matrices such as these were originally envisioned for burning plutonium from dismantled nuclear weapons [1]. However, because they achieve a conversion ratio of zero, they have also been considered as a better alternative to MOX [2-6]. Plutonium and minor actinides dominate the long term heat and radiological outputs from spent nuclear fuel. Recent work has shown that that IMFs can be used to reduce these outputs by at least a factor of four, on a per unit of energy generated basis [6]. The degree of reduction is strongly dependent on IMF burnup. In principle, complete transmutation of the transuranics could be achieved though this

Indigenous food ingredients for complementary food formulations to combat infant malnutrition in Benin

NARCIS (Netherlands)

Chadare, Flora J.; Madode, Yann E.; Fanou-Fogny, Nadia; Kindossi, Janvier M.; Ayosso, Juvencio O.G.; Honfo, S.H.; Kayodé, A.P.P.; Linnemann, Anita R.; Hounhouigan, D.J.

2018-01-01

This paper reviews indigenous Beninese food resources as potential ingredients for complementary infant foods with the aim to develop affordable formulations for low-income households in each agro-ecological zone of the country. Potential ingredients were selected on their documented nutritional

Responses of dogs with food allergies to single-ingredient dietary provocation.

Science.gov (United States)

Jeffers, J G; Meyer, E K; Sosis, E J

1996-08-01

To characterize specific food ingredients causing allergic reactions in dogs and to assess cross-reactivity between proteins derived from a single animal source or from different plant products. Prospective study. 25 dogs with histories and cutaneous signs consistent with food-allergic dermatitis. Dogs were fed a food-elimination diet until resolution of clinical signs and then challenged with their original diet. A diagnosis of food allergy was made if there was complete return of pruritus within 14 days of challenge exposure. After diagnosis, dogs were fed the food-elimination diet until signs related to dietary challenge abated. The dogs then were fed beef, chicken, chicken eggs, cows' milk, wheat, soy, and corn in single-ingredient provocation trials for 1 week. Any cutaneous reactions to these food ingredients were recorded by their owners. Beef and soy most often caused adverse cutaneous reactions, although all ingredients induced clinical signs in at least 1 dog. Mean number of allergens per dog was 2.4, with 80% reacting to 1 or 2 proteins and 64% reacting to 2 or more of the proteins tested. A significant difference was found between dogs reacting to beef versus cows' milk and between dogs reacting to soy versus wheat; thus, the hypothesis of cross-reactivity to ingredients derived from a single animal source or to different plant products was not supported. Similar differences between chicken meat and eggs were not identified. Long-term management of dogs with food allergies is facilitated by identification of the most commonly encountered food allergens. Because cross-reactivity cannot be verified, each protein source should be included separately in food-provocation trials.

The inert doublet model: a new archetype of WIMP dark matter?

International Nuclear Information System (INIS)

Tytgat, M Hg

2008-01-01

The Inert Doublet Model (IDM) is a two doublet extension of the Higgs-Brout-Englert sector of the Standard Model with a Z2 symmetry in order to prevent FCNC. If the Z2 symmetry is not spontaneously broken, the lightest neutral extra scalar is a dark matter candidate. We briefly review the phenomenology of the model, emphasizing its relevance for the issue of Electroweak Symmetry Breaking (EWSB) and the prospects for detection of dark matter

Bomb radiocarbon in metabolically inert tissues from terrestrial and marine mammals

International Nuclear Information System (INIS)

Bada, J.L.; Vrolijk, C.D.; Brown, S.; Druffel, E.R.M.; Hedges, R.E.M.

1987-01-01

We report here radiocarbon measurements of monkey eye lens nucleus proteins and a narwhal tusk, biological tissues which have sampled the bomb radiocarbon signal in different ways. The results confirm the metabolic inertness of eye lens nucleus proteins and demonstrate the feasibility of measuring radiocarbon in small samples of biological tissue using accelerator mass spectrometry (AMS). The narwhal tusk provides a unique record of the radiocarbon activity in Arctic Ocean waters over most of the 20th century

21 CFR 184.1355 - Helium.

Science.gov (United States)

2010-04-01

... colorless, odorless, flavorless, nonflammable, inert gas. It is lighter than air and is produced by the liquefaction and purification of natural gas. (b) The ingredient must be of a purity suitable for its intended...

Effects of radiative heat transfer on the turbulence structure in inert and reacting mixing layers

International Nuclear Information System (INIS)

Ghosh, Somnath; Friedrich, Rainer

2015-01-01

We use large-eddy simulation to study the interaction between turbulence and radiative heat transfer in low-speed inert and reacting plane temporal mixing layers. An explicit filtering scheme based on approximate deconvolution is applied to treat the closure problem arising from quadratic nonlinearities of the filtered transport equations. In the reacting case, the working fluid is a mixture of ideal gases where the low-speed stream consists of hydrogen and nitrogen and the high-speed stream consists of oxygen and nitrogen. Both streams are premixed in a way that the free-stream densities are the same and the stoichiometric mixture fraction is 0.3. The filtered heat release term is modelled using equilibrium chemistry. In the inert case, the low-speed stream consists of nitrogen at a temperature of 1000 K and the highspeed stream is pure water vapour of 2000 K, when radiation is turned off. Simulations assuming the gas mixtures as gray gases with artificially increased Planck mean absorption coefficients are performed in which the large-eddy simulation code and the radiation code PRISSMA are fully coupled. In both cases, radiative heat transfer is found to clearly affect fluctuations of thermodynamic variables, Reynolds stresses, and Reynolds stress budget terms like pressure-strain correlations. Source terms in the transport equation for the variance of temperature are used to explain the decrease of this variance in the reacting case and its increase in the inert case

A method for determining optimum phasing of a multiphase propulsion system for a single-stage vehicle with linearized inert weight

Science.gov (United States)

Martin, J. A.

1974-01-01

A general analytical treatment is presented of a single-stage vehicle with multiple propulsion phases. A closed-form solution for the cost and for the performance and a derivation of the optimal phasing of the propulsion are included. Linearized variations in the inert weight elements are included, and the function to be minimized can be selected. The derivation of optimal phasing results in a set of nonlinear algebraic equations for optimal fuel volumes, for which a solution method is outlined. Three specific example cases are analyzed: minimum gross lift-off weight, minimum inert weight, and a minimized general function for a two-phase vehicle. The results for the two-phase vehicle are applied to the dual-fuel rocket. Comparisons with single-fuel vehicles indicate that dual-fuel vehicles can have lower inert weight either by development of a dual-fuel engine or by parallel burning of separate engines from lift-off.

21 CFR 101.4 - Food; designation of ingredients.

Science.gov (United States)

2010-04-01

... ingredient shall be a specific name and not a collective (generic) name, except that: (1) Spices, flavorings..., concentrated milk, reconstituted milk, and dry whole milk may be declared as “milk”. (5) Bacterial cultures may...

Spectroscopic Diagnostics of Barrier Discharge Plasmas in Mixtures of Zinc Diiodide with Inert Gases

International Nuclear Information System (INIS)

Guivan, N.N.; Malinin, A.N.

2005-01-01

The spectral characteristics of the emission of gas discharge atmospheric pressure plasmas in mixtures of zinc diiodide vapor with inert gases (He, Ne, Ar, Kr, and Xe) are investigated. The formation of a gas discharge plasma and the excitation of the components of a working mixture were performed in a high-frequency (with a repetition frequency of sinusoidal voltage pulses of 100 kHz) barrier discharge. The gas discharge emission was analyzed in the spectral range 200-900 nm with a resolution of 0.05 nm. Emission bands of ZnI(B-X) exciplex molecules and I* 2 excimer molecules, lines of inert gases, and emission bands of XeI* exciplex molecules (in Xe-containing mixtures) were revealed. It is ascertained that the strongest emission of ZnI* molecules is observed in ZnI 2 /He(Ne) mixtures. The regularities in the spectral characteristics of the gas discharge plasma emission are considered

ON THE VIABILITY OF THE PAH MODEL AS AN EXPLANATION OF THE UNIDENTIFIED INFRARED EMISSION FEATURES

International Nuclear Information System (INIS)

Zhang, Yong; Kwok, Sun

2015-01-01

Polycyclic aromatic hydrocarbon (PAH) molecules are widely considered the preferred candidate for the carrier of the unidentified infrared emission bands observed in the interstellar medium and circumstellar envelopes. In this paper, we report the results of fitting a variety of non-PAH spectra (silicates, hydrogenated amorphous carbon, coal, and even artificial spectra) using the theoretical infrared spectra of PAHs from the NASA Ames PAH IR Spectroscopic Database. We show that these non-PAH spectra can be well fitted by PAH mixtures. This suggests that a general match between astronomical spectra and those of PAH mixtures does not necessarily provide definitive support for the PAH hypothesis

Ingredients of success in the design and construction of the french nuclear power plants

International Nuclear Information System (INIS)

Bacher, P.; Panossian, J.; Riollet, G.

1989-01-01

A nuclear program can be compared to a pastry. There are many ingredients, a lot of know-how, an adequate cooking and some good luck to achieve success or back luck to fail. The French nuclear program has had all the ingredients of success and the necessary luck. The present paper presents the major ingredients: strong and well defined policies, an adapted industrial organization, original management methods, dedicated men, political and popular support. The main results of the French program, well known today, are only briefly be presented. The last part of the paper show the very strong interactions between operation and design, and how experience is fed back into the design both of new and of older plants. The conclusion calls for new ingredients for future success

Consumer product chemical weight fractions from ingredient lists

Science.gov (United States)

Assessing human exposures to chemicals in consumer products requires composition information. However, comprehensive composition data for products in commerce are not generally available. Many consumer products have reported ingredient lists that are constructed using specific gu...

Effects of tailoring ingredients in auditory persuasive health messages on fruit and vegetable intake

NARCIS (Netherlands)

Elbert, Sarah P.; Dijkstra, Arie; Rozema, Andrea

2017-01-01

Objective: Health messages can be tailored by applying different tailoring ingredients, among which personalisation, feedback and adaptation. This experiment investigated the separate effects of these tailoring ingredients on behaviour in auditory health persuasion. Furthermore, the moderating

Fixed-Dose Combination Drug Approvals, Patents and Market Exclusivities Compared to Single Active Ingredient Pharmaceuticals.

Science.gov (United States)

Hao, Jing; Rodriguez-Monguio, Rosa; Seoane-Vazquez, Enrique

2015-01-01

Fixed-dose combinations (FDC) contain two or more active ingredients. The effective patent and exclusivity life of FDC compared to single active ingredient has not been assessed. Trends in FDA approved FDC in the period 1980-2012 and time lag between approval of FDC and single active ingredients in the combination were assessed, and the effective patent and exclusivity life of FDC was compared with their single active ingredients. New molecular entities (NMEs), new therapeutic biologics license applications (BLAs) and FDC data were collected from the FDA Orange Book and Drugs@FDA. Analysis included FDC containing one or more NMEs or BLAs at first FDA approval (NMEs-FDC) and only already marketed drugs (Non-NMEs-FDC). Descriptive, Kruskal-Wallis and Wilcoxon Rank Sum analyses were performed. During the study period, the FDA approved 28 NMEs-FDC (3.5% of NMEs) and 117 non-NMEs-FDC. FDC approvals increased from 12 in the 1980s to 59 in the 2000s. Non-NMEs-FDC entered the market at a median of 5.43 years (interquartile range 1.74, 10.31) after first FDA approval of single active ingredients in the combination. The Non-NMEs-FDC entered the market at a median of 2.33 years (-7.55, 2.39) before approval of generic single active ingredient. Non-NME-FDC added a median of 9.70 (2.75, 16.24) years to the patent and exclusivity life of the single active ingredients in the combination. FDC approvals significantly increased over the last twenty years. Pharmaceutical companies market FDC drugs shortly before the generic versions of the single ingredients enter the market extending the patent and exclusivity life of drugs included in the combination.

Fixed-Dose Combination Drug Approvals, Patents and Market Exclusivities Compared to Single Active Ingredient Pharmaceuticals.

Directory of Open Access Journals (Sweden)

Jing Hao

Full Text Available Fixed-dose combinations (FDC contain two or more active ingredients. The effective patent and exclusivity life of FDC compared to single active ingredient has not been assessed.Trends in FDA approved FDC in the period 1980-2012 and time lag between approval of FDC and single active ingredients in the combination were assessed, and the effective patent and exclusivity life of FDC was compared with their single active ingredients.New molecular entities (NMEs, new therapeutic biologics license applications (BLAs and FDC data were collected from the FDA Orange Book and Drugs@FDA. Analysis included FDC containing one or more NMEs or BLAs at first FDA approval (NMEs-FDC and only already marketed drugs (Non-NMEs-FDC. Descriptive, Kruskal-Wallis and Wilcoxon Rank Sum analyses were performed.During the study period, the FDA approved 28 NMEs-FDC (3.5% of NMEs and 117 non-NMEs-FDC. FDC approvals increased from 12 in the 1980s to 59 in the 2000s. Non-NMEs-FDC entered the market at a median of 5.43 years (interquartile range 1.74, 10.31 after first FDA approval of single active ingredients in the combination. The Non-NMEs-FDC entered the market at a median of 2.33 years (-7.55, 2.39 before approval of generic single active ingredient. Non-NME-FDC added a median of 9.70 (2.75, 16.24 years to the patent and exclusivity life of the single active ingredients in the combination.FDC approvals significantly increased over the last twenty years. Pharmaceutical companies market FDC drugs shortly before the generic versions of the single ingredients enter the market extending the patent and exclusivity life of drugs included in the combination.

Microalgae as healthy ingredients for functional food: a review.

Science.gov (United States)

Matos, J; Cardoso, C; Bandarra, N M; Afonso, C

2017-08-01

Microalgae are very interesting and valuable natural sources of highly valuable bioactive compounds, such as vitamins, essential amino acids, polyunsaturated fatty acids, minerals, carotenoids, enzymes and fibre. Due to their potential, microalgae have become some of the most promising and innovative sources of new food and functional products. Moreover, microalgae can be used as functional ingredients to enhance the nutritional value of foods and, thus, to favourably affect human health by improving the well-being and quality of life, but also by curtailing disease and illness risks. This review provides an overview of the current knowledge of the health benefits associated with the consumption of microalgae, bioactive compounds, functional ingredients, and health foods.

Huangqin-Tang and Ingredients in Modulating the Pathogenesis of Ulcerative Colitis.

Science.gov (United States)

Wang, Chunyan; Tang, Xudong; Zhang, Li

2017-01-01

Ulcerative colitis (UC) is the most common inflammatory bowel disease worldwide. Current therapies in UC cause limitations, and herb medicine provides an important choice for UC treatment. Huangqin-Tang (HQT) is a well-known classical traditional Chinese herbal formula and has been used in China for thousands of years. A large number of pharmacological studies demonstrated HQT and its ingredients to be effective in treating UC. Though the therapeutic effect has been evaluated, comprehensive up-to-date reviews in this field are not yet available. Here we aim to review our current understanding of HQT and its ingredients in treating UC and how the agents modulate the main pathogenesis of the disease, including the intestinal environment, immune imbalance, inflammatory pathways, and oxidative stress. The summary on this issue may provide better understanding of HQT and its ingredients in treating UC and possibly help in promoting its clinical application.

Identification and Structural Characterization of Unidentified Impurity in Bisoprolol Film-Coated Tablets

Directory of Open Access Journals (Sweden)

Ivana Mitrevska

2017-01-01

Full Text Available The aim of this study is the identification, structural characterization, and qualification of a degradation impurity of bisoprolol labeled as Impurity RRT 0.95. This degradation product is considered as a principal thermal degradation impurity identified in bisoprolol film-coated tablets. The impurity has been observed in the stress thermal degradation study of the drug product. Using HPLC/DAD/ESI-MS method, a tentative structure was assigned and afterwards confirmed by detailed structural characterization using NMR spectroscopy. The structure of the target Impurity RRT 0.95 was elucidated as phosphomonoester of bisoprolol, having relative molecular mass of 406 (positive ionization mode. The structural characterization was followed by qualification of Impurity RRT 0.95 using several different in silico methodologies. From the results obtained, it can be concluded that no new structural alerts have been generated for Impurity RRT 0.95 relative to the parent compound bisoprolol. The current study presents an in-depth analysis of the full characterization and qualification of an unidentified impurity in a drug product with the purpose of properly defining the quality specification of the product.

Substances inertes et plantes à effet insecticide utilisées dans la ...

African Journals Online (AJOL)

Les insecticides naturels tels que les plantes à effet insecticide et les substances inertes (sable, cendre, terres à diatomées,…) méritent d'être valorisées afin de réduire l'utilisation des insecticides chimiques et protéger l'environnement. Ce travail basé sur une revue documentaire fouillée et actualisée vise à faire la genèse ...

Assessment of a chemical getter for scavenging tritium from an inert gas

International Nuclear Information System (INIS)

Maienschein, J.L.

1976-01-01

Results are presented of a study aimed at determining the feasibility of using chemical getter beds to scavenge tritium from inert gases. Two types of getter bed, fixed and fluidized, were considered, using cerium as the getter material. Mathematical-modeling results and capital-cost estimates indicate that not only is the gettering approach technically feasible, it could lead to considerable cost savings over catalytic oxidation, the tritium-removal method traditionally used

[A systematic review of the effectiveness of alternative weight-loss products' ingredients].

Science.gov (United States)

de Lira-García, Cynthia; Souto-Gallardo, María; Bacardí-Gascón, Monserrat; Jiménez-Cruz, Arturo

2008-01-01

The high demand for obesity treatment and conventional therapies' lack of effectiveness increases the use of alternative products. This study was aimed at assessing evidence from randomised clinical trials regarding the effectiveness of alternative weight-loss products' ingredients. A survey was conducted in Ensenada, Baja California, to assess the frequency of consuming alternative products used for weight reduction. The ingredients in the products most in demand were included in this review. The Pubmed database was searched for all randomised clinical trial papers including these ingredients and assessing weight loss. Thirty-six percent of the subjects questioned had used alternative methods for weight-loss, 83% of them being women. The most frequently used products were shakes, tea, pills and flaxseed/linseed. Sixteen randomised clinical trials using four ingredients were used: Garcinia cambogia, green tea, L-carnitina and flaxseed. Only two studies (green tea and Garcinia cambogia) showed significant weight-loss (25%) amongst control and experimental groups. There was no significant difference between the groups in the studies regarding L-carnitina and flaxseed. There is a lack of evidence regarding quality studies justifying the use of alternative products for weight loss.

Consensus Modeling for Prediction of Estrogenic Activity of Ingredients Commonly Used in Sunscreen Products

Directory of Open Access Journals (Sweden)

Huixiao Hong

2016-09-01

Full Text Available Sunscreen products are predominantly regulated as over-the-counter (OTC drugs by the US FDA. The “active” ingredients function as ultraviolet filters. Once a sunscreen product is generally recognized as safe and effective (GRASE via an OTC drug review process, new formulations using these ingredients do not require FDA review and approval, however, the majority of ingredients have never been tested to uncover any potential endocrine activity and their ability to interact with the estrogen receptor (ER is unknown, despite the fact that this is a very extensively studied target related to endocrine activity. Consequently, we have developed an in silico model to prioritize single ingredient estrogen receptor activity for use when actual animal data are inadequate, equivocal, or absent. It relies on consensus modeling to qualitatively and quantitatively predict ER binding activity. As proof of concept, the model was applied to ingredients commonly used in sunscreen products worldwide and a few reference chemicals. Of the 32 chemicals with unknown ER binding activity that were evaluated, seven were predicted to be active estrogenic compounds. Five of the seven were confirmed by the published data. Further experimental data is needed to confirm the other two predictions.

Nb-TiO{sub 2}/polymer hybrid solar cells with photovoltaic response under inert atmosphere conditions

Energy Technology Data Exchange (ETDEWEB)

Lira-Cantu, Monica; Khoda Siddiki, Mahbube; Munoz-Rojas, David; Amade, Roger [Centre d' Investigacio en Nanociencia i Nanotecnologia (CIN2, CSIC), Laboratory of Nanostructured Materials for Photovoltaic Energy, Campus UAB, Barcelona (Spain); Gonzalez-Pech, Natalia I. [Centre d' Investigacio en Nanociencia i Nanotecnologia (CIN2, CSIC), Laboratory of Nanostructured Materials for Photovoltaic Energy, Campus UAB, Barcelona (Spain); Instituto Tecnologico y de Estudios Superiores de Monterrey (ITESM), Ave. Eugenio Garza Sada, 64640 Monterrey, N.L. (Mexico)

2010-07-15

Hybrid Solar Cells (HSC) applying Nb-TiO{sub 2} in direct contact with a conducting organic polymer, MEH-PPV, show higher stability than the bare TiO{sub 2}-based HSC when analyzed under inert atmosphere conditions. IPCE analyses revealed that inert atmospheres affect directly the semiconductor oxide in the first stages of the analyses but photovoltaic performance stabilizes after several hours. A 20 wt% Nb-doped TiO{sub 2} presented the highest stability and photovoltaic properties. The behavior has been attributed to the solubility limit of Nb within the TiO{sub 2} beyond 20 wt% doping level where the co-existence of NbO{sub 2} is observed. The HSCs were analyzed under controlled N{sub 2} atmosphere and 1000 W/m{sup 2} (AM 1.5) irradiation. (author)

Coeficientes de digestibilidade aparente da proteína e energia de alguns ingredientes utilizados em dietas para o pintado (Pseudoplatystoma coruscans Apparent digestibility coefficients of protein and energy of some ingredients used in diets for pintado, Pseudoplatystoma coruscans (Agassiz, 1829

Directory of Open Access Journals (Sweden)

Emílio Guedes Gonçalves

2003-08-01

Full Text Available O presente trabalho foi desenvolvido com o objetivo de determinar os coeficientes de digestibilidade aparente da proteína e da energia dos principais alimentos utilizados na formulação de dietas para alevinos de pintado. Foram utilizados 600 alevinos com peso médio inicial de 9,80 ± 1,48 g e comprimento total médio de 13,00 ± 1,00 cm. Na coleta de fezes, foi utilizado o sistema de Guelph modificado. As 12 dietas-teste foram constituídas por 69,50% de uma dieta de referência, 0,50% de óxido de cromo (marcador inerte e 30% do ingrediente estudado. Após receberem as dietas teste durante três dias, os peixes foram transferidos para os aquários de coleta (incubadoras de fibra de vidro de 80 litros de capacidade, onde as fezes foram coletadas em intervalos de meia hora. Com base nos coeficientes de digestibilidade da fração protéica, os alimentos que apresentaram maior aproveitamento para esse nutriente foram: farinha de peixe (84,14%, farelo de soja (67,10%, milho (64,18% e farinha de vísceras de aves (61,25%. Foram observados valores razoáveis somente para a digestibilidade do conteúdo energético em metade dos ingredientes estudados; para as farinhas de peixe, milho, soja integral tostada e os farelos de soja, de trigo e de arroz, os coeficientes médios foram: 72,80; 57,39; 64,95; 61,66; 53,20 e 51,84%, respectivamente. A farinha de peixe foi o melhor ingrediente para o pintado (45,38% PD e 2790,42 kcal ED/kg, seguido do farelo de soja (30,86% PD e 2708,45 kcal ED/kg, da soja integral tostada (18,34% PD e 3121,06 kcal ED/kg, do milho (5,86% PD e 2691,53 kcal ED/kg e do farelo de trigo (8,08% PD e 2265,13 kcal ED/kg.The present work was developed in order to determine the protein and energy apparent digestibility coefficients of the principal ingredients used in the pintado juvenile diets. Six hundred juveniles with initial weight and total length means of 9.80 ± 1.48 g and 13.00 ± 1.00 cm, respectively, were used. The modified

Criteria for development of a database for safety evaluation of fragrance ingredients.

Science.gov (United States)

Ford, R A; Domeyer, B; Easterday, O; Maier, K; Middleton, J

2000-04-01

Over 2000 different ingredients are used in the manufacture of fragrances. The majority of these ingredients have been used for many decades. Despite this long history of use, all of these ingredients need continued monitoring to ensure that each ingredient meets acceptable safety standards. As with other large databases of existing chemicals, fulfilling this need requires an organized approach to identify the most important potential hazards. One such approach, specifically considering the dermal route of exposure as the most relevant one for fragrance ingredients, has been developed. This approach provides a rational selection of materials for review and gives guidance for determining the test data that would normally be considered necessary for the elevation of safety under intended conditions of use. As a first step, the process takes into account the following criteria: quantity of use, consumer exposure, and chemical structure. These are then used for the orderly selection of materials for review with higher quantity, higher exposure, and the presence of defined structural alerts all contributing to a higher priority for review. These structural alerts along with certain exposure and volume limits are then used to develop guidelines for determining the quality and quantity of data considered necessary to support an adequate safety evaluation of the chosen materials, taking into account existing data on the substance itself as well as on closely related analogs. This approach can be considered an alternative to testing; therefore, it is designed to be conservative but not so much so as to require excessive effort when not justified.

Antiulcerogenic benefits of herbal ingredients in ethanol-induced ...

African Journals Online (AJOL)

Antiulcerogenic benefits of herbal ingredients in ethanol-induced animal models. ... Although therapeutic approaches are widely available, preventive regimens are limited. Numerous studies have demonstrated that herbal ... gastric ulcer. Key words: Herbal Medicines, Gastric ulcer, Prevention, Animal models, Alcohol ...

21 CFR 352.10 - Sunscreen active ingredients.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Sunscreen active ingredients. 352.10 Section 352.10 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... until further notice. For the convenience of the user, the revised text is set forth as follows: § 352...

What are the "ingredients" for economic growth?

OpenAIRE

Wolla, Scott A.

2013-01-01

Is there a recipe for economic growth? Perhaps some Miracle-Gro for the economy? If only it were that easy. While the exact recipe is a mystery, economists have identified some of the key ingredients. This month’s newsletter discusses the role that economic institutions play in fostering long-term economic growth.

Viking Helmet Corroles: Activating Inert Oxidometal Corroles.

Science.gov (United States)

Schweyen, Peter; Brandhorst, Kai; Hoffmann, Martin; Wolfram, Benedikt; Zaretzke, Marc-Kevin; Bröring, Martin

2017-10-09

Chemically inert oxidometal(V) corrols of molybdenum and rhenium undergo clean ligand-exchange reactions upon the action of SiCl 4 . The resulting dichlorido complexes show trigonal prismatic coordination of the metal ion with the chlorine atoms residing in a cis configuration, and were studied by optical and resonance spectroscopy as well as DFT calculations. In situ reactivity studies with carbon nucleophiles indicate high reactivity for chlorine replacement. Treatment with sodium cyclopentadienide paves the way to robust molybdenum corrolocene half-sandwich complexes. These organometallic compounds are the first corrole species that stabilize an air-stable and diamagnetic low spin d 2 -Mo IV center. Structural, spectroelectrochemical, and chemical investigations prove a reversible Mo IV /Mo V redox couple close to the Fc/Fc + potential for these systems. The high stability of the compounds in both redox states calls for future applications in catalysis and as redox switch. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Valorization of postharvest sweet cherry discard for the development of dehydrated fruit ingredients: compositional, physical, and mechanical properties.

Science.gov (United States)

Franceschinis, Lorena; Sette, Paula; Salvatori, Daniela; Schebor, Carolina

2018-04-20

Sweet cherries are an excellent source of phenolic compounds, which may contribute to a healthy diet. The objective of this work was to generate dehydrated ingredients from postharvest discard of sweet cherries. Four dried ingredients were obtained from fresh sweet cherry discard (Lapins var.) using an osmotic dehydration pretreatment and freeze drying or air drying. The ingredients showed an important phenolic contribution (2.8-6.6 g gallic acid kg -1 of product) and preserved the natural color of the fruit to a great extent. Freeze-dried ingredients were less hygroscopic than air-dried ones, and presented with a softer texture. All the ingredients were in a supercooled state at room temperature (T g range: -23.0 to -18.8 °C). Sugar infusion pretreatment caused a decrease in water sorption capacity and molecular mobility; it also reduced the initial rehydration rate. Relevant differences in nutritional and structural characteristics of the ingredients were observed depending on the processing method used. These ingredients could be incorporated into different processed foods, such as snacks, cereal mixtures, cereal bars, and bakery and confectionery products. Air-dried control ingredients presented better nutritional qualities and air-dried sweet cherries with sugar infusion pretreatment could be appropriate ingredients for applications where sweet flavor and slow rehydration rate are required. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

The Optimum Plutonium Inert Matrix Fuel Form for Reactor-Based Plutonium Disposition

International Nuclear Information System (INIS)

Tulenko, J.S.; Wang, J.; Acosta, C.

2004-01-01

The University of Florida has underway an ongoing research program to validate the economic, operational and performance benefits of developing an inert matrix fuel (IMF) for the disposition of the U.S. weapons plutonium (Pu) and for the recycle of reprocessed Pu. The current fuel form of choice for Pu disposition for the Department of Energy is as a mixed oxide (MOX) (PuO2/UO2). We will show analyses that demonstrate that a Silicon Carbide (SiC) IMF offers improved performance capabilities as a fuel form for Pu recycle and disposition. The reason that UF is reviewing various materials to serve as an inert matrix fuel is that an IMF fuel form can offer greatly reduced Pu and transuranic isotope (TRU) production and also improved thermal performance characteristics. Our studies showed that the Pu content is reduced by an order of magnitude while centerline fuel temperatures are reduced approximately 380 degrees centigrade compared to MOX. These reduced temperatures result in reduced stored heat and thermal stresses in the pellet. The reduced stored heat reduces the consequences of the loss of coolant accident, while the reduced temperatures and thermal stresses yield greatly improved fuel performance. Silicon Carbide is not new to the nuclear industry, being a basic fuel material in gas cooled reactors

Radiochemical neutron activation analysis for trace elements of basic ingredients of pan

International Nuclear Information System (INIS)

Zaidi, J.H.; Arif, M.; Fatima, I; Qureshi, I.H.

2002-01-01

Extensive use of pan, by one-tenth of world's population, entails the evaluation of trace element contents in its ingredients. Radiochemical neutron activation analysis (RNAA) was developed and successfully employed to determine the concentration of 36 trace elements (essential, toxic and nonessential) in its four basic ingredients, leaf of betel pepper, betel nut, catechu and lime. The radiochemical separation methodology has significantly improved the detection limits of most of these elements due to suppression of Compton background. Base-line values of certain toxic and essential elements in these ingredients is provided. The daily intake of essential and toxic elements through pan was estimated and compared with the recommended values. The cumulative intake of Mn is four times higher than the recommended value and that of toxic elements is well below the tolerance limits. (author)

Occurrence of ochratoxin A in poultry feeds and feed ingredients from Pakistan.

Science.gov (United States)

Sherazi, S T H; Shar, Z H; Sumbal, G A; Tan, Eddie T; Bhanger, M I; Kara, Huseyin; Nizamani, S M

2015-02-01

A study was conducted to evaluate the occurrence of ochratoxin A (OTA) in complete poultry feeds (n=80) and poultry feed ingredients (n=286) from Pakistan. All samples were first analyzed by indirect enzyme linked immunosorbent assay (ELISA), samples with OTA concentrations above the European Union maximum regulatory limit (MRL, 100 μg/kg) were further confirmed by HPLC-FLD. Contamination frequency and mean OTA levels were 31% and 51 μg/kg in feed ingredients, and the corresponding values for complete feeds were 38% and 75 μg/kg. Ten samples of complete poultry feed and 19 samples of feed ingredients contained OTA at levels higher than the MRL. The results of the present study indicate that there is a strong need for a more intense monitoring programs for OTA in poultry feed.

Molecular detection of Setaria tundra (Nematoda: Filarioidea and an unidentified filarial species in mosquitoes in Germany

Directory of Open Access Journals (Sweden)

Czajka Christina

2012-01-01

Full Text Available Abstract Background Knowledge of the potential vector role of Culicidae mosquitoes in Germany is very scanty, and until recently it was generally assumed that they are not involved in the transmission of anthroponotic or zoonotic pathogens in this country. However, anticipated changes in the course of global warming and globalization may alter their status. Methods We conducted a molecular mass screening of mosquitoes for filarial parasites using mitochondrial 12S rRNA-based real-time PCR. Results No parasites causing disease in humans such as Dirofilaria spp. were detected in about 83,000 mosquitoes tested, which had been collected in 2009 and 2010 in 16 locations throughout Germany. However, minimum infection rates of up to 24 per 1000 mosquitoes were revealed, which could be attributed to mosquito infection with Setaria tundra and a yet unidentified second parasite. Setaria tundra was found to be widespread in southern Germany in various mosquito species, except Culex spp. In contrast, the unidentified filarial species was exclusively found in Culex spp. in northern Baden-Württemberg, and is likely to be a bird parasite. Conclusions Although dirofilariasis appears to be emerging and spreading in Europe, the absence of Dirofilaria spp. or other zoonotic filariae in our sample allows the conclusion that the risk of autochthonous infection in Germany is still very low. Potential vectors of S. tundra in Germany are Ochlerotatus sticticus, Oc. cantans, Aedes vexans and Anopheles claviger. Technically, the synergism between entomologists, virologists and parasitologists, combined with state-of-the-art methods allows a very efficient near-real-time monitoring of a wide spectrum of both human and veterinary pathogens, including new distribution records of parasite species and the incrimination of their potential vectors.

Data-mining of potential antitubercular activities from molecular ingredients of traditional Chinese medicines.

Science.gov (United States)

Jamal, Salma; Scaria, Vinod

2014-01-01

Background. Traditional Chinese medicine encompasses a well established alternate system of medicine based on a broad range of herbal formulations and is practiced extensively in the region for the treatment of a wide variety of diseases. In recent years, several reports describe in depth studies of the molecular ingredients of traditional Chinese medicines on the biological activities including anti-bacterial activities. The availability of a well-curated dataset of molecular ingredients of traditional Chinese medicines and accurate in-silico cheminformatics models for data mining for antitubercular agents and computational filters to prioritize molecules has prompted us to search for potential hits from these datasets. Results. We used a consensus approach to predict molecules with potential antitubercular activities from a large dataset of molecular ingredients of traditional Chinese medicines available in the public domain. We further prioritized 160 molecules based on five computational filters (SMARTSfilter) so as to avoid potentially undesirable molecules. We further examined the molecules for permeability across Mycobacterial cell wall and for potential activities against non-replicating and drug tolerant Mycobacteria. Additional in-depth literature surveys for the reported antitubercular activities of the molecular ingredients and their sources were considered for drawing support to prioritization. Conclusions. Our analysis suggests that datasets of molecular ingredients of traditional Chinese medicines offer a new opportunity to mine for potential biological activities. In this report, we suggest a proof-of-concept methodology to prioritize molecules for further experimental assays using a variety of computational tools. We also additionally suggest that a subset of prioritized molecules could be used for evaluation for tuberculosis due to their additional effect against non-replicating tuberculosis as well as the additional hepato-protection offered by

D- and I-optimal design of mixture experiments in the presence of ingredient availability constraints

OpenAIRE

SYAFITRI, Utami; SARTONO, Bagus; GOOS, Peter

2015-01-01

Mixture experiments usually involve various constraints on the proportions of the ingredients of the mixture under study. In this paper, inspired by the fact that the available stock of certain ingredients is often limited, we focus on a new type of constraint, which we refer to as an ingredient availability constraint. This type of constraint substantially complicates the search for optimal designs for mixture experiments. One difficulty, for instance, is that the optimal number of experimen...

Ingredients for Good Health Policy-Making: Incorporating Power and Politics into the Mix

Directory of Open Access Journals (Sweden)

Yusra Shawar

2014-05-01

Full Text Available Eggs, flour, sugar, butter, baking soda, milk, and vanilla extract—all ingredients necessary to make a delicious cake. Similarly, good health policy-making can only be successfully pursued and understood by accounting for all of its basic ingredients, including the role of politics and power. Otherwise, the result is simply not good.

The effect on lactic fermentation of concentrating inert material with immobilised cells in a calcium alginate biocatalyser

Directory of Open Access Journals (Sweden)

Juan Carlos Serrato

2005-05-01

Full Text Available Colombia is one of the world’s main sugarcane cultivating countries but it has not diversified its fermentation industry; a few fermentation industries produce alcohol and yeasts. Lactic acid and its derivatives then become alternatives providing added value to the sugar produced, thus benefiting the regions producing the sugar.This work evaluated the kinetics of lactic acid production using immobilised cells in calcium alginate at different concentrations of inert material. Lactobacillus delbrueckiI was the microorganism used and fermentation broth mainly consisted of sucrose and yeast exact. CSTR reactors were used without pH control. The results suggested that 2% to 3% inert material in the biocatalyst increased cellular retention and diffusiveness, leading to improved conversion and reaction rate.

Marketing dietary supplements in the United States: A review of the requirements for new dietary ingredients

International Nuclear Information System (INIS)

Noonan, Chris; Patrick Noonan, W.

2006-01-01

Since the passage of the Dietary Supplement Health and Education Act in 1994, the marketplace for dietary supplements has experienced dramatic growth. New products have redefined the entire marketplace, and new ingredients are introduced to consumers at lightning speed. As part of this act, laws were passed to ensure the safety of new dietary ingredients introduced into the United States marketplace. But more than 11 years later, these laws are frequently misunderstood, and more frequently ignored. This article reviews the regulatory landscape of new dietary ingredients and defines the issues manufacturers must contend with to legally market dietary supplements with new dietary ingredients in the U.S

21 CFR 700.15 - Use of certain halogenated salicylanilides as ingredients in cosmetic products.

Science.gov (United States)

2010-04-01

... ingredients in cosmetic products. 700.15 Section 700.15 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) COSMETICS GENERAL Requirements for Specific Cosmetic Products § 700.15 Use of certain halogenated salicylanilides as ingredients in cosmetic products. (a...

Origin of Spectral Band Patterns in the Cosmic Unidentified Infrared Emission

Science.gov (United States)

Álvaro Galué, Héctor; Díaz Leines, Grisell

2017-10-01

The cosmic unidentified infrared emission (UIE) band phenomenon is generally considered as indicative of free-flying polycyclic aromatic hydrocarbon molecules in space. However, a coherent explanation of emission spectral band patterns depending on astrophysical source is yet to be resolved under this attribution. Meanwhile astronomers have restored the alternative origin as due to amorphous carbon particles, but assigning spectral patterns to specific structural elements of particles is equally challenging. Here we report a physical principle in which inclusion of nonplanar structural defects in aromatic core molecular structures (π domains) induces spectral patterns typical of the phenomenon. We show that defects in model π domains modulate the electronic-vibration coupling that activates the delocalized π -electron contribution to aromatic vibrational modes. The modulation naturally disperses C =C stretch modes in band patterns that readily resemble the UIE bands in the elusive 6 - 9 μ m range. The electron-vibration interaction mechanics governing the defect-induced band patterns underscores the importance of π delocalization in the emergence of UIE bands. We discuss the global UIE band regularity of this range as compatible with an emission from the delocalized s p2 phase, as π domains, confined in disordered carbon mixed-phase aggregates.

Does the Addition of Inert Gases at Constant Volume and Temperature Affect Chemical Equilibrium?

Science.gov (United States)

Paiva, Joao C. M.; Goncalves, Jorge; Fonseca, Susana

2008-01-01

In this article we examine three approaches, leading to different conclusions, for answering the question "Does the addition of inert gases at constant volume and temperature modify the state of equilibrium?" In the first approach, the answer is yes as a result of a common students' alternative conception; the second approach, valid only for ideal…

Choleretic Activity of Turmeric and its Active Ingredients.

Science.gov (United States)

Wang, Yonglu; Wang, Liyao; Zhu, Xinyi; Wang, Dong; Li, Xueming

2016-07-01

Turmeric, a rhizome of Curcumin longa L. is widely used as both a spice and an herbal medicine. The traditional use of turmeric in gastroenterology is mainly based on its choleretic activity. The aim of this study is to determine the effects of turmeric on bile flow (BF) and total bile acids (TBAs) excretion in a bile fistula rat model after acute duodenal administration. A significant dose-dependent enhancement in both BF and TBAs was detected after treatment with the turmeric decoctions which suggested the choleretic activity was bile acid-dependent secretion. In order to direct the active group of compounds, aqueous (AE), ethyl acetate (EtOAc), and petroleum ether (PE) extracts were investigated. The EtOAc and PE extracts showing high effects were purified to locate the active ingredients. Three curcuminoids (curcumin, demethoxycurcumin, and bisdemethoxycurcumin) and 2 sesquiterpenes (bisacurone B and ar-turmerone) were isolated. It was found Bisacurone B was the most potent choleretic ingredient followed by ar-turmerone, bisdemethoxycurcumin demethoxycurcumin, and then curcumin. The amounts of the active ingredients were quantitatively analyzed by high-performance liquid chromatography. The EtOAc and PE extracts had high sesquiterpenes and curcuminoids content, while the AE extract had poor content of sesquiterpenes and curcuminoids which affected neither BF nor TBAs. Based on the results of multiple linear regression analysis, the content of BIS and TUR were dominant factors (P < 0.01) of controlling BL and TBAs in EtOAC and PE extracts. © 2016 Institute of Food Technologists®

Permeation, diffusion and dissolution of hydrogen isotopes, methane and inert gases through/in a tetrafluoroethylene film

International Nuclear Information System (INIS)

Matsuyama, M.; Miyake, H.; Ashida, K.; Watanabe, K.

1982-01-01

Tetrafluoroethylene (TFE) is widely used for conventional tritium handling systems such as vacuum seals, tubing and so on. We measured the permeation of the three hydrogen isotopes, methane and the inert gases through a TFE film at room temperature by means of the time-lag method in order to establish the physicochemical properties which determine the solubility and diffusivity of those gases. It was found that the diffusion constant of the inert gases changed exponentially with the heat of vaporization and the solubility was an exponential function of the Lennard-Jones force constant of the gases. On the other hand, hydrogen isotopes and methane deviated from these relations. It is concluded that chemical interactions between the solute and the solvent play an important role for the dissolution and the diffusion of these gases in TFE. (orig.)

Advances in ingredient and processing systems for meat and meat products.

Science.gov (United States)

Weiss, Jochen; Gibis, Monika; Schuh, Valerie; Salminen, Hanna

2010-09-01

Changes in consumer demand of meat products as well as increased global competition are causing an unprecedented spur in processing and ingredient system developments within the meat manufacturing sector. Consumers demand healthier meat products that are low in salt, fat, cholesterol, nitrites and calories in general and contain in addition health-promoting bioactive components such as for example carotenoids, unsaturated fatty acids, sterols, and fibers. On the other hand, consumers expect these novel meat products with altered formulations to taste, look and smell the same way as their traditionally formulated and processed counterparts. At the same time, competition is forcing the meat processing industry to use the increasingly expensive raw material "meat" more efficiently and produce products at lower costs. With these changes in mind, this article presents a review of novel ingredient systems and processing approaches that are emerging to create high quality, affordable meat products not only in batch mode but also in large-scale continuous processes. Fat replacers, fat profile modification and cholesterol reduction techniques, new texture modifiers and alternative antioxidant and antimicrobial systems are being discussed. Modern processing equipment to establish continuously operating product manufacturing lines and that allow new meat product structures to be created and novel ingredients to be effectively utilized including vacuum fillers, grinders and fine dispersers, and slicers is reviewed in the context of structure creation in meat products. Finally, trends in future developments of ingredient and processing systems for meat products are highlighted.

Purification of inert gas circuits of nuclear power facilities from tritium and hydrogen

International Nuclear Information System (INIS)

Eichler, R.

1985-08-01

Removing hydrogen and tritium from the inert primary coolant of a high temperature reactor is very important in regard to the process heat disposition. In this work a gas purification for a high temperature module reactor was laid out constructionally and researched technically. This system removes the contamination of the primary circuit with the aid of chemical getter beds of Cer alloy particles. (orig./PW) [de

Method of enhanced lithiation of doped silicon carbide via high temperature annealing in an inert atmosphere

Science.gov (United States)

Hersam, Mark C.; Lipson, Albert L.; Bandyopadhyay, Sudeshna; Karmel, Hunter J; Bedzyk, Michael J

2014-05-27

A method for enhancing the lithium-ion capacity of a doped silicon carbide is disclosed. The method utilizes heat treating the silicon carbide in an inert atmosphere. Also disclosed are anodes for lithium-ion batteries prepared by the method.

Study on THz spectra of the active ingredients in the TCM

Science.gov (United States)

Ma, ShiHua; Wang, WenFeng; Liu, GuiFeng; Ge, Min; Zhu, ZhiYong

2008-03-01

Terahertz spectroscopy has tremendous potential for applications to evaluate the quality of the drugs including the TCM. In this paper, the Terahertz Time-Domain Spectroscopy investigated two active ingredients: Andrographolide and Dehydroandrographoline, isolated from Andrographis paniculata (Burm. f.) Nees. We also measured the mixtures of two active ingredients at the different ratio and the quantitative analysis is also applied to determine the contents of compound. The Terahertz spectroscopy is a potential and promising technique in identifying the components, evaluating the drugs sanitation and inspecting the quality of medicine including TCM.

Modelling the transient behaviour of pulsed current tungsten-inert-gas weldpools

Science.gov (United States)

Wu, C. S.; Zheng, W.; Wu, L.

1999-01-01

A three-dimensional model is established to simulate the pulsed current tungsten-inert-gas (TIG) welding process. The goal is to analyse the cyclic variation of fluid flow and heat transfer in weldpools under periodic arc heat input. To this end, an algorithm, which is capable of handling the transience, nonlinearity, multiphase and strong coupling encountered in this work, is developed. The numerical simulations demonstrate the transient behaviour of weldpools under pulsed current. Experimental data are compared with numerical results to show the effectiveness of the developed model.

Effect of several food ingredients on radiation inactivation of Escherichia coli and Listeria monocytogenes inoculated into ground pork

International Nuclear Information System (INIS)

Yun, Hyejeong; Lacroix, Monique; Jung, Samooel; Kim, Keehyuk; Lee, Ju Woon; Jo, Cheorun

2011-01-01

The objective of this study was to examine the effects of several food ingredients on the relative radiation sensitivity (RRS) of Escherichia coli and Listeria monocytogenes inoculated onto ground pork. Garlic, leek, onion, and ginger were prepared in 3 different forms; pressurized, freeze-dried, and 70% ethanol extracted. The prepared food ingredients were subdivided into 2 groups, non-irradiated and irradiated with 5 kGy of gamma irradiation, before addition to ground pork. The prepared food ingredients were added at concentrations of 1% and 5% (w/w) into radiation-sterilized ground pork and inoculated with E. coli and L. monocytogenes (10 6 CFU/mL). For E. coli inoculated pork, the most efficient ingredient was ethanol extracted leek (RRS=3.89), followed by freeze-dried ginger and leek (RRS=3.66 and 3.63, respectively) when used without pasteurization. However, when the food ingredients were irradiation-pasteurized, the freeze-dried ginger showed the highest RRS (4.10). When 5% natural materials were added, RRS was the highest for freeze-dried and ethanol extracted onion (4.44 and 4.65, respectively). For L. monocytogenes, the RRS was relatively lower than E. coli in general. The most efficient material was pressurized and freeze-dried onion (RRS=2.13 and 2.08, respectively) at a concentration of 1%. No increase in RRS was observed at increased concentration of food ingredients. These results suggest that the addition of particular food ingredients increased the efficiency of radiation-sterilization. However, changes in RRS were dependent on the species of microorganism as well as the form of the food ingredients. - Highlights: → Several food ingredients increased the efficiency of irradiation sterilization. → Different forms of food ingredients may affect the efficiency. → The increase of efficiency decreased the required irradiation dose, thereby avoiding sensory impairments of food.

Effect of several food ingredients on radiation inactivation of Escherichia coli and Listeria monocytogenes inoculated into ground pork

Energy Technology Data Exchange (ETDEWEB)

Yun, Hyejeong [Department of Animal Science and Biotechnology, Chungnam National University, Daejeon 305-764 (Korea, Republic of); Lacroix, Monique [Canadian Irradiation Center, Research Laboratory in Science Applied to Food, INRS-Institut Armand-Frappier, Qebec (Canada); Jung, Samooel [Department of Animal Science and Biotechnology, Chungnam National University, Daejeon 305-764 (Korea, Republic of); Kim, Keehyuk [Department of Culinary Nutrition, Woosong University, Daejeon 300-718 (Korea, Republic of); Lee, Ju Woon [Advanced Radiation Technology Institute, Korea Atomic Energy Research Institute, Jeongeup 580-185 (Korea, Republic of); Jo, Cheorun, E-mail: cheorun@cnu.ac.kr [Department of Animal Science and Biotechnology, Chungnam National University, Daejeon 305-764 (Korea, Republic of)

2011-09-15

The objective of this study was to examine the effects of several food ingredients on the relative radiation sensitivity (RRS) of Escherichia coli and Listeria monocytogenes inoculated onto ground pork. Garlic, leek, onion, and ginger were prepared in 3 different forms; pressurized, freeze-dried, and 70% ethanol extracted. The prepared food ingredients were subdivided into 2 groups, non-irradiated and irradiated with 5 kGy of gamma irradiation, before addition to ground pork. The prepared food ingredients were added at concentrations of 1% and 5% (w/w) into radiation-sterilized ground pork and inoculated with E. coli and L. monocytogenes (10{sup 6} CFU/mL). For E. coli inoculated pork, the most efficient ingredient was ethanol extracted leek (RRS=3.89), followed by freeze-dried ginger and leek (RRS=3.66 and 3.63, respectively) when used without pasteurization. However, when the food ingredients were irradiation-pasteurized, the freeze-dried ginger showed the highest RRS (4.10). When 5% natural materials were added, RRS was the highest for freeze-dried and ethanol extracted onion (4.44 and 4.65, respectively). For L. monocytogenes, the RRS was relatively lower than E. coli in general. The most efficient material was pressurized and freeze-dried onion (RRS=2.13 and 2.08, respectively) at a concentration of 1%. No increase in RRS was observed at increased concentration of food ingredients. These results suggest that the addition of particular food ingredients increased the efficiency of radiation-sterilization. However, changes in RRS were dependent on the species of microorganism as well as the form of the food ingredients. - Highlights: > Several food ingredients increased the efficiency of irradiation sterilization. > Different forms of food ingredients may affect the efficiency. > The increase of efficiency decreased the required irradiation dose, thereby avoiding sensory impairments of food.

Mobility of supercooled liquid toluene, ethylbenzene, and benzene near their glass transition temperatures investigated using inert gas permeation.

Science.gov (United States)

May, R Alan; Smith, R Scott; Kay, Bruce D

2013-11-21

We investigate the mobility of supercooled liquid toluene, ethylbenzene, and benzene near their respective glass transition temperatures (Tg). The permeation rate of Ar, Kr, and Xe through the supercooled liquid created when initially amorphous overlayers are heated above their glass transition temperature is used to determine the diffusivity. Amorphous benzene crystallizes at temperatures well below its Tg, and as a result, the inert gas underlayer remains trapped until the onset of benzene desorption. In contrast, for toluene and ethylbenzene the onset of inert gas permeation is observed at temperatues near Tg. The inert gas desorption peak temperature as a function of the heating rate and overlayer thickness is used to quantify the diffusivity of supercooled liquid toluene and ethylbenzene from 115 to 135 K. In this temperature range, diffusivities are found to vary across 5 orders of magnitude (∼10(-14) to 10(-9) cm(2)/s). The diffusivity data are compared to viscosity measurements and reveal a breakdown in the Stokes-Einstein relationship at low temperatures. However, the data are well fit by the fractional Stokes-Einstein equation with an exponent of 0.66. Efforts to determine the diffusivity of a mixture of benzene and ethylbenzene are detailed, and the effect of mixing these materials on benzene crystallization is explored using infrared spectroscopy.

Minimum ignition energy of nano and micro Ti powder in the presence of inert nano TiO₂ powder.

Science.gov (United States)

Chunmiao, Yuan; Amyotte, Paul R; Hossain, Md Nur; Li, Chang

2014-06-15

The inerting effect of nano-sized TiO2 powder on ignition sensitivity of nano and micro Ti powders was investigated with a Mike 3 apparatus. "A little is not good enough" is also suitable for micro Ti powders mixed with nano-sized solid inertants. MIE of the mixtures did not significantly increase until the TiO2 percentage exceeded 50%. Nano-sized TiO2 powders were ineffective as an inertant when mixed with nano Ti powders, especially at higher dust loadings. Even with 90% nano TiO2 powder, mixtures still showed high ignition sensitivity because the statistic energy was as low as 2.1 mJ. Layer fires induced by ignited but unburned metal particles may occur for micro Ti powders mixed with nano TiO2 powders following a low level dust explosion. Such layer fires could lead to a violent dust explosion after a second dispersion. Thus, additional attention is needed to prevent metallic layer fires even where electric spark potential is low. In the case of nano Ti powder, no layer fires were observed because of less flammable material involved in the mixtures investigated, and faster flame propagation in nanoparticle clouds. Copyright © 2014 Elsevier B.V. All rights reserved.

Cadmium contamination in cereal-based diets and diet ingredients

International Nuclear Information System (INIS)

Siitonen, P.H.; Thompson, H.C. Jr.

1990-01-01

Cereal-based diet and/or diet ingredient cadmium levels were determined by graphite furnace AAS. Cadmium contamination was 88.3 and 447 ppb in two cereal-based diets, 44.6 and 48.9 ppb in two purified diets, and ranged from less than 1.1 to 22,900 ppb in the ingredients of one cereal-based diet. The major source of cadmium contamination was attributed to the calcium supplement used for diet formulation. Comparative analyses of two purified diet samples and one cereal-based diet by the National Institute of Standards and Technology (NIST, formerly the National Bureau of Standards) and the National Center for Toxicological Research (NCTR) gave virtually identical results for Cd. A comparative study of Cd levels determined by flame and furnace AAS was also made by the NCTR and the NIST

Exploring Cu2O/Cu cermet as a partially inert anode to produce aluminum in a sustainable way

International Nuclear Information System (INIS)

Feng, Li-Chao; Xie, Ning; Shao, Wen-Zhu; Zhen, Liang; Ivanov, V.V.

2014-01-01

Highlights: • Cu 2 O/Cu cermet was used as a candidate partially inert anode material to produce aluminum alloys. • The thermal corrosion behavior of Cu 2 O/Cu was investigated in molten salt at 960 °C. • The corrosion rate is largely governed by the geometrical structures of Cu in the prepared samples. • The corrosion rate increases with decreasing sizes and increasing filling contents of Cu phase. • The corrosion rate was 1.8–9 cm/y and the Cu contents is less than 6.2 wt.% in the produced aluminum. - Abstract: As an energy-intensive process, aluminum production by the Hall–Héroult method accounts for significant emissions of CO 2 and some toxic greenhouse gases. The utilization of an inert anode in place of a carbon anode was considered as a revolutionary technique to solve most of the current environmental problems resulting from the Hall–Héroult process. However, the critical property requirements of the inert anode materials significantly limit the application of this technology. In light of the higher demand for aluminum alloys than for pure aluminum, a partially inert anode was designed to produce aluminum alloys in a more sustainable way. Here, Cu 2 O/Cu cermet was chosen as the material of interest. The thermal corrosion behavior of Cu 2 O/Cu was investigated in Na 3 AlF 6 –CaF 2 –Al 2 O 3 electrolyte at 960 °C to elucidate the corrosion mechanisms of this type of partially inert anode for the production of aluminum or aluminum alloys. Furthermore, the effects of the geometrical structure of the Cu phase on the thermal corrosion behavior of Cu 2 O/Cu cermet in the electrolyte were investigated as well. The thermal corrosion rate was evaluated by the weight loss method and the results show that the samples prepared with branch-like Cu have higher thermal corrosion rate than those prepared with spherical Cu, and the corrosion rate increases with decreasing size and increasing filling content of Cu phase. The calculated corrosion rate

Kinetics of thermal decomposition of aluminium hydride: I-non-isothermal decomposition under vacuum and in inert atmosphere (argon)

International Nuclear Information System (INIS)

Ismail, I.M.K.; Hawkins, T.

2005-01-01

Recently, interest in aluminium hydride (alane) as a rocket propulsion ingredient has been renewed due to improvements in its manufacturing process and an increase in thermal stability. When alane is added to solid propellant formulations, rocket performance is enhanced and the specific impulse increases. Preliminary work was performed at AFRL on the characterization and evaluation of two alane samples. Decomposition kinetics were determined from gravimetric TGA data and volumetric vacuum thermal stability (VTS) results. Chemical analysis showed the samples had 88.30% (by weight) aluminium and 9.96% hydrogen. The average density, as measured by helium pycnometery, was 1.486 g/cc. Scanning electron microscopy showed that the particles were mostly composed of sharp edged crystallographic polyhedral such as simple cubes, cubic octahedrons and hexagonal prisms. Thermogravimetric analysis was utilized to investigate the decomposition kinetics of alane in argon atmosphere and to shed light on the mechanism of alane decomposition. Two kinetic models were successfully developed and used to propose a mechanism for the complete decomposition of alane and to predict its shelf-life during storage. Alane decomposes in two steps. The slowest (rate-determining) step is solely controlled by solid state nucleation of aluminium crystals; the fastest step is due to growth of the crystals. Thus, during decomposition, hydrogen gas is liberated and the initial polyhedral AlH 3 crystals yield a final mix of amorphous aluminium and aluminium crystals. After establishing the kinetic model, prediction calculations indicated that alane can be stored in inert atmosphere at temperatures below 10 deg. C for long periods of time (e.g., 15 years) without significant decomposition. After 15 years of storage, the kinetic model predicts ∼0.1% decomposition, but storage at higher temperatures (e.g. 30 deg. C) is not recommended

Design and validation of inert homemade explosive simulants for ground penetrating radar

Science.gov (United States)

VanderGaast, Brian W.; McFee, John E.; Russell, Kevin L.; Faust, Anthony A.

2015-05-01

The Canadian Armed Forces (CAF) identified a requirement for inert simulants to act as improvised, or homemade, explosives (IEs) when training on, or evaluating, ground penetrating radar (GPR) systems commonly used in the detection of buried landmines and improvised explosive devices (IEDs). In response, Defence R and D Canada (DRDC) initiated a project to develop IE simulant formulations using commonly available inert materials. These simulants are intended to approximate the expected GPR response of common ammonium nitrate-based IEs, in particular ammonium nitrate/fuel oil (ANFO) and ammonium nitrate/aluminum (ANAl). The complex permittivity over the range of electromagnetic frequencies relevant to standard GPR systems was measured for bulk quantities of these three IEs that had been fabricated at DRDC Suffield Research Centre. Following these measurements, published literature was examined to find benign materials with both a similar complex permittivity, as well as other physical properties deemed desirable - such as low-toxicity, thermal stability, and commercial availability - in order to select candidates for subsequent simulant formulation. Suitable simulant formulations were identified for ANFO, with resulting complex permittivities measured to be within acceptable limits of target values. These IE formulations will now undergo end-user trials with CAF operators in order to confirm their utility. Investigations into ANAl simulants continues. This progress report outlines the development program, simulant design, and current validation results.

Safety Evaluation of Cosmetic Ingredients Regarding Their Skin Sensitization Potential

Directory of Open Access Journals (Sweden)

Winfried Steiling

2016-03-01

Full Text Available Up to today, product safety evaluation in the EU is predominantly based on data/information on their individual ingredients. Consequently, the quality and reliability of individual ingredient data is of vital interest. In this context, the knowledge about skin sensitization potential is an explicit need for both hazard and risk assessment. Proper skin sensitization data of the individual chemicals is essential, especially when dermal contact is intended, like for cosmetics. In some cases, e.g., in the presence of irritating chemicals, the combination of individual ingredients may also need to be evaluated to cover possible mixture effects. Today, it seems unlikely or even impossible that skin sensitization in humans can be adequately described by a single test result or even by a simple combination of a few data points (in vivo or in vitro. It is becoming evident that a set of data (including human data and market data and knowledge about the ingredient’s specific sensitizing potency needs to be taken into account to enable a reliable assessment of skin sensitization. A more in-depth understanding on mechanistic details of the Adverse-Outcome-Pathway of skin sensitization could contribute key data for a robust conclusion on skin sensitization.

Irradiation of inert matrix and mixed oxide fuel in the Halden test reactor

International Nuclear Information System (INIS)

Hellwig, Ch.; Kasemeyer, U.

2001-01-01

In a new type of fuel, called Inert Matrix Fuel (IMF), plutonium is embedded in a U-free matrix. This offers advantages for more efficient plutonium consumption, higher proliferation resistance, and for inert behaviour later in a waste repository. In the fuel type investigated at PSI, plutonium is dissolved in yttrium-stabilized zirconium oxide (YSZ), a highly radiation-resistant cubic phase, with addition of erbium as burnable poison for reactivity control. A first irradiation experiment of YSZ-based IMF is ongoing in the OECD Material Test Reactor in Halden (HBWR), together with MOX fuel (Rig IFA-651.1). The experiment is described herein and results are presented of the first 120 days of irradiation with an average assembly burnup of 47 kWd/cm 3 . The results are compared with neutronic calculations performed before the experiment, and are used to model the fuel behaviour with the PSI-modified TRANSURANUS code. The measured fuel temperatures are within the expected range. An unexpectedly strong densification of the IMF during the first irradiation cycle does not alter the fuel temperatures. An explanation for this behaviour is proposed. The irradiation at higher linear heat rates during forthcoming cycles will deliver information about the fission gas release behaviour of the IMF. (author)

Irradiation of inert matrix and mixed oxide fuel in the Halden test reactor

Energy Technology Data Exchange (ETDEWEB)

Hellwig, Ch.; Kasemeyer, U

2001-03-01

In a new type of fuel, called Inert Matrix Fuel (IMF), plutonium is embedded in a U-free matrix. This offers advantages for more efficient plutonium consumption, higher proliferation resistance, and for inert behaviour later in a waste repository. In the fuel type investigated at PSI, plutonium is dissolved in yttrium-stabilized zirconium oxide (YSZ), a highly radiation-resistant cubic phase, with addition of erbium as burnable poison for reactivity control. A first irradiation experiment of YSZ-based IMF is ongoing in the OECD Material Test Reactor in Halden (HBWR), together with MOX fuel (Rig IFA-651.1). The experiment is described herein and results are presented of the first 120 days of irradiation with an average assembly burnup of 47 kWd/cm{sup 3}. The results are compared with neutronic calculations performed before the experiment, and are used to model the fuel behaviour with the PSI-modified TRANSURANUS code. The measured fuel temperatures are within the expected range. An unexpectedly strong densification of the IMF during the first irradiation cycle does not alter the fuel temperatures. An explanation for this behaviour is proposed. The irradiation at higher linear heat rates during forthcoming cycles will deliver information about the fission gas release behaviour of the IMF. (author)

Exploiting the plutonium stockpiles in PWRs by using inert matrix fuel

International Nuclear Information System (INIS)

Lombardi, C.; Mazzola, A.

1996-01-01

The plutonium coming from dismantled warheads and that already stockpiled coming from spent fuel reprocessing have raised many concerns related to proliferation resistance, environmental safety and economy. The option of disposing of plutonium by fission is one of the most widely discussed and many proposals for plutonium burning in a safe and economical manner have been put forward. Due to their diffusion, PWRs appear to be the main candidates for the reduction of the plutonium stockpiles. In order to achieve a high plutonium consumption rate, a uranium-free fuel may be conceived, based on the dilution of PuO 2 within a carrier matrix made of inert oxide. In this paper, a partial loading of inert matrix fuel in a current technology PWR was investigated with 3-D calculations. The results indicated that this solution has good plutonium elimination capabilities: commercial PWRs operating in a once-through cycle scheme can transmute more than 98% of the loaded Pu-239 and 73 or 81% of the overall initially loaded reactor grade or weapons grade plutonium, respectively. The plutonium still let in the spent fuel was of poor quality and then offered a better proliferation resistance. Power peaking problems could be faced with the adoption of burnable absorbers: IFBA seemed to be particularly suitable. In spite of a reduction of the overall plutonium loaded mass by a factor 3.7 or 5.4 depending on its quality, there was no evidence of an increase of the minor actinides radiotoxicity after a time period of about 25 years. (author)

Network Understanding of Herb Medicine via Rapid Identification of Ingredient-Target Interactions

Science.gov (United States)

Zhang, Hai-Ping; Pan, Jian-Bo; Zhang, Chi; Ji, Nan; Wang, Hao; Ji, Zhi-Liang

2014-01-01

Today, herb medicines have become the major source for discovery of novel agents in countermining diseases. However, many of them are largely under-explored in pharmacology due to the limitation of current experimental approaches. Therefore, we proposed a computational framework in this study for network understanding of herb pharmacology via rapid identification of putative ingredient-target interactions in human structural proteome level. A marketing anti-cancer herb medicine in China, Yadanzi (Brucea javanica), was chosen for mechanistic study. Total 7,119 ingredient-target interactions were identified for thirteen Yadanzi active ingredients. Among them, about 29.5% were estimated to have better binding affinity than their corresponding marketing drug-target interactions. Further Bioinformatics analyses suggest that simultaneous manipulation of multiple proteins in the MAPK signaling pathway and the phosphorylation process of anti-apoptosis may largely answer for Yadanzi against non-small cell lung cancers. In summary, our strategy provides an efficient however economic solution for systematic understanding of herbs' power.

Wigner's infinite spin representations and inert matter

Energy Technology Data Exchange (ETDEWEB)

Schroer, Bert [CBPF, Rio de Janeiro (Brazil); Institut fuer Theoretische Physik FU-Berlin, Berlin (Germany)

2017-06-15

Positive energy ray representations of the Poincare group are naturally subdivided into three classes according to their mass and spin content: m > 0, m = 0 finite helicity and m = 0 infinite spin. For a long time the localization properties of the massless infinite spin class remained unknown, until it became clear that such matter does not permit compact spacetime localization and its generating covariant fields are localized on semi-infinite space-like strings. Using a new perturbation theory for higher spin fields we present arguments which support the idea that infinite spin matter cannot interact with normal matter and we formulate conditions under which this also could happen for finite spin s > 1 fields. This raises the question of a possible connection between inert matter and dark matter. (orig.)

NOx emission control in SI engine by adding argon inert gas to intake mixture

International Nuclear Information System (INIS)

Moneib, Hany A.; Abdelaal, Mohsen; Selim, Mohamed Y.E.; Abdallah, Osama A.

2009-01-01

The Argon inert gas is used to dilute the intake air of a spark ignition engine to decrease nitrogen oxides and improve the performance of the engine. A research engine Ricardo E6 with variable compression was used in the present work. A special test rig has been designed and built to admit the gas to the intake air of the engine for up to 15% of the intake air. The system could admit the inert gas, oxygen and nitrogen gases at preset amounts. The variables studied included the engine speed, Argon to inlet air ratio, and air to fuel ratio. The results presented here included the combustion pressure, temperature, burned mass fraction, heat release rate, brake power, thermal efficiency, volumetric efficiency, exhaust temperature, brake specific fuel consumption and emissions of CO, CO 2 , NO and O 2 . It was found that the addition of Argon gas to the intake air of the gasoline engine causes the nitrogen oxide to reduce effectively and also it caused the brake power and thermal efficiency of the engine to increase. Mathematical program has been used to obtain the mixture properties and the heat release when the Argon gas is used.

New viable region of an inert Higgs doublet dark matter model with scotogenic extension

Science.gov (United States)

Borah, Debasish; Gupta, Aritra

2017-12-01

We explore the intermediate dark matter mass regime of the inert Higgs doublet model, approximately between 400 and 550 GeV, which is allowed by latest constraints from direct and indirect detection experiments, but the thermal relic abundance remains suppressed. We extend the model by three copies of right-handed neutrinos, odd under the built-in Z2 symmetry of the model. This discrete Z2 symmetry of the model allows these right-handed neutrinos to couple to the usual lepton doublets through the inert Higgs doublet allowing the possibility of radiative neutrino mass in the scotogenic fashion. Apart from generating nonzero neutrino mass, such an extension can also revive the intermediate dark matter mass regime. The late decay of the lightest right-handed neutrino to dark matter makes it possible for the usual thermally underabundant dark matter in this intermediate mass regime to satisfy the correct relic abundance limit. The revival of this wide intermediate mass range can have relevance not only for direct and indirect search experiments but also for neutrino experiments as the long lifetime of the lightest right-handed neutrino also results in almost vanishing lightest neutrino mass.

Green plasticizers for multibase gun propellants (Lecture)

NARCIS (Netherlands)

Schoolderman, C.; Driel, C.A. van; Zebregs, M.

2007-01-01

TNO Defence, Security and Safety has a long history of research on gun propellants. Areas investigated are formulating (new ingredients, optimization), manufacturing, charge design and lifetime assessment [1,2,3,4,5]. In conventional propellants inert plasticizers are used to alter performance,

7 CFR 58.634 - Assembling and combining mix ingredients.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Assembling and combining mix ingredients. 58.634 Section 58.634 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) REGULATIONS...

Compound forming extractants, solvating solvents and inert solvents IUPAC chemical data series

CERN Document Server

Marcus, Y; Kertes, A S

2013-01-01

Equilibrium Constants of Liquid-Liquid Distribution Reactions, Part III: Compound Forming Extractants, Solvating Solvents, and Inert Solvents focuses on the compilation of equilibrium constants of various compounds, such as acids, ions, salts, and aqueous solutions. The manuscript presents tables that show the distribution reactions of carboxylic and sulfonic acid extractants and their dimerization and other reactions in the organic phase and extraction reactions of metal ions from aqueous solutions. The book also states that the inorganic anions in these solutions are irrelevant, since they d

Inert tracer wind resuspension as a function of wind speed, atmospheric stability, and initial tracer particle size

International Nuclear Information System (INIS)

Sehmel, G.A.; Lloyd, F.D.

1979-01-01

Wind-caused resuspension rates are being determined in three different, long-term, inert-tracer field experiments. Chemical results were recently received from an accumulated backlog of air filter samples. Resuspension rates are yet to be calculated from these data

Thermal degradation of CR-39 polymer in an inert atmosphere

International Nuclear Information System (INIS)

Kalsi, P.C.; Pandey, A.K.; Iyer, R.H.; Singh Mudher, K.D.

1995-01-01

The thermal degradation of CR-39 (allyl diglycol carbonate), a polymer widely used in nuclear science and technology, in an inert atmosphere has been studied using thermogravimetric analysis (TGA) and differential thermal analysis (DTA) techniques. The results are compared with the thermal degradation data of the polymer in an air atmosphere. The present studies showed that the thermal degradation of the polymer proceeds in two steps in an argon atmosphere as compared to three steps in air atmosphere. The mass losses in air are higher than that in argon due to the oxidative decomposition of the residue. The kinetics of the different stages of degradation were also evaluated from the TG curves. (author). 7 refs., 1 tab

Muon implantation in inert gases studied by radio frequency spectroscopy

International Nuclear Information System (INIS)

Johnson, C; Cottrell, S P; Ghandi, K; Fleming, D G

2005-01-01

Diamagnetic and muonium (Mu) fractions formed in low-pressure inert gases, by energetic muon implantation, have been studied using the technique of time-delayed radio frequency muon spin resonance (RF-μSR). Results obtained establish the validity of the long-held view that formation of these species is due only to prompt processes, and in turn confirms that the diamagnetic environment is due to a muon molecular ion, MMu + , and not a bare μ + . In addition, polarization fractions for the diamagnetic and Mu environments have been determined at different pressures, thereby complementing earlier data, and demonstrating that the RF-μSR technique provides polarization fractions in good accord with those obtained using conventional transverse-field muon spin resonance measurements

A Limited Survey of Aflatoxins in Poultry Feed and Feed Ingredients in Guyana

Directory of Open Access Journals (Sweden)

Donna M. Morrison

2017-11-01

Full Text Available A study was conducted to determine the presence of aflatoxins in finished poultry feed from manufacturing companies, feed ingredients, and poultry feed at the point of sale. Two collections were made. In the first collection, samples of the finished feed and feed ingredients were analyzed by high-performance liquid chromatography (HPLC. For the second collection, all samples were analyzed by ELISA while a subset was analyzed by HPLC. Of the 27 samples of finished feed, five samples had aflatoxin concentrations greater than the United States Food and Drug Administration (USFDA and European Union Commission (EUC maximum tolerable limit of 20 µg/kg, while for the feed ingredients, three of the 30 samples of feed ingredients exceeded the limit. Of the 93 samples of finished feed purchased from retailers, five samples had aflatoxin concentrations greater than the maximum tolerable limit. This survey indicates that most of the samples were below the maximum regulatory limit and maintained quality up to the point of sale for 2015 and 2016. However, given that some samples were above the limit, there is a need to monitor the production and marketing chain to ensure that the quality of the finished feed is not compromised.

Assessment of Stress Corrosion Cracking Resistance of Activated Tungsten Inert Gas-Welded Duplex Stainless Steel Joints

Science.gov (United States)

Alwin, B.; Lakshminarayanan, A. K.; Vasudevan, M.; Vasantharaja, P.

2017-12-01

The stress corrosion cracking behavior of duplex stainless steel (DSS) weld joint largely depends on the ferrite-austenite phase microstructure balance. This phase balance is decided by the welding process used, heat input, welding conditions and the weld metal chemistry. In this investigation, the influence of activated tungsten inert gas (ATIG) and tungsten inert gas (TIG) welding processes on the stress corrosion cracking (SCC) resistance of DSS joints was evaluated and compared. Boiling magnesium chloride (45 wt.%) environment maintained at 155 °C was used. The microstructure and ferrite content of different weld zones are correlated with the outcome of sustained load, SCC test. Irrespective of the welding processes used, SCC resistance of weld joints was inferior to that of the base metal. However, ATIG weld joint exhibited superior resistance to SCC than the TIG weld joint. The crack initiation and final failure were in the weld metal for the ATIG weld joint; they were in the heat-affected zone for the TIG weld joint.

Some results on development, irradiation and post-irradiation examinations of fuels for fast reactor-actinide burner (MOX and inert matrix fuel)

International Nuclear Information System (INIS)

Poplavsky, V.; Zabudko, L.; Moseev, L.; Rogozkin, B.; Kurina, I.

1996-01-01

Studies performed have shown principal feasibility of the BN-600 and BN-800 cores to achieve high efficiency of Pu burning when MOX fuel with Pu content up to 45% is used. Valuable experience on irradiation behaviour of oxide fuel with high Pu content (100%) was gained as a result of operation of two BR-10 core loadings where the maximum burnup 14 at.% was reached. Post-irradiation examination (PIE) allowed to reveal some specific features of the fuel with high plutonium content. Principal irradiation and PIE results are presented in the paper. Use of new fuel without U-238 provides the maximum burning capability as in this case the conversion ratio is reduced to zero. Technological investigations of inert matrix fuels have been continued now. Zirconium carbide, zirconium nitride, magnesium oxide and other matrix materials are under consideration. Inert matrices selection criteria are discussed in the paper. Results of technological study, of irradiation in the BOR-60 reactor and PIE results of some inert matrix fuels are summarized in this report. (author). 2 refs, 1 fig., 3 tabs

Effect of several food ingredients on radiation inactivation of Escherichia coli and Listeria monocytogenes inoculated into ground pork

Science.gov (United States)

Yun, Hyejeong; Lacroix, Monique; Jung, Samooel; Kim, Keehyuk; Lee, Ju Woon; Jo, Cheorun

2011-09-01

The objective of this study was to examine the effects of several food ingredients on the relative radiation sensitivity (RRS) of Escherichia coli and Listeria monocytogenes inoculated onto ground pork. Garlic, leek, onion, and ginger were prepared in 3 different forms; pressurized, freeze-dried, and 70% ethanol extracted. The prepared food ingredients were subdivided into 2 groups, non-irradiated and irradiated with 5 kGy of gamma irradiation, before addition to ground pork. The prepared food ingredients were added at concentrations of 1% and 5% (w/w) into radiation-sterilized ground pork and inoculated with E. coli and L. monocytogenes (10 6 CFU/mL). For E. coli inoculated pork, the most efficient ingredient was ethanol extracted leek (RRS=3.89), followed by freeze-dried ginger and leek (RRS=3.66 and 3.63, respectively) when used without pasteurization. However, when the food ingredients were irradiation-pasteurized, the freeze-dried ginger showed the highest RRS (4.10). When 5% natural materials were added, RRS was the highest for freeze-dried and ethanol extracted onion (4.44 and 4.65, respectively). For L. monocytogenes, the RRS was relatively lower than E. coli in general. The most efficient material was pressurized and freeze-dried onion (RRS=2.13 and 2.08, respectively) at a concentration of 1%. No increase in RRS was observed at increased concentration of food ingredients. These results suggest that the addition of particular food ingredients increased the efficiency of radiation-sterilization. However, changes in RRS were dependent on the species of microorganism as well as the form of the food ingredients.

The impact of whole human blood on the kinetic inertness of platinum(iv) prodrugs - an HPLC-ICP-MS study.

Science.gov (United States)

Theiner, Sarah; Grabarics, Márkó; Galvez, Luis; Varbanov, Hristo P; Sommerfeld, Nadine S; Galanski, Markus; Keppler, Bernhard K; Koellensperger, Gunda

2018-04-17

The potential advantage of platinum(iv) complexes as alternatives to classical platinum(ii)-based drugs relies on their kinetic stability in the body before reaching the tumor site and on their activation by reduction inside cancer cells. In this study, an analytical workflow has been developed to investigate the reductive biotransformation and kinetic inertness of platinum(iv) prodrugs comprising different ligand coordination spheres (respectively, lipophilicity and redox behavior) in whole human blood. The distribution of platinum(iv) complexes in blood pellets and plasma was determined by inductively coupled plasma-mass spectrometry (ICP-MS) after microwave digestion. An analytical approach based on reversed-phase (RP)-ICP-MS was used to monitor the parent compound and the formation of metabolites using two different extraction procedures. The ligand coordination sphere of the platinum(iv) complexes had a significant impact on their accumulation in red blood cells and on their degree of kinetic inertness in whole human blood. The most lipophilic platinum(iv) compound featuring equatorial chlorido ligands showed a pronounced penetration into blood cells and a rapid reductive biotransformation. In contrast, the more hydrophilic platinum(iv) complexes with a carboplatin- and oxaliplatin-core exerted kinetic inertness on a pharmacologically relevant time scale with notable amounts of the compound accumulated in the plasma fraction.

Multiplicities of charged pions and unidentified charged hadrons from deep-inelastic scattering of muons off an isoscalar target

CERN Document Server

Adolph, C.; Aghasyan, M.; Akhunzyanov, R.; Alexeev, M.G.; Alexeev, G.D.; Amoroso, A.; Andrieux, V.; Anfimov, N.V.; Anosov, V.; Augustyniak, W.; Austregesilo, A.; Azevedo, C.D.R.; Badelek, B.; Balestra, F.; Barth, J.; Beck, R.; Bedfer, Y.; Bernhard, J.; Bicker, K.; Bielert, E.R.; Birsa, R.; Bisplinghoff, J.; Bodlak, M.; Boer, M.; Bordalo, P.; Bradamante, F.; Braun, C.; Bressan, A.; Buechele, M.; Capozza, L.; Chang, W. -C.; Chatterjee, C.; Chiosso, M.; Choi, I.; Chung, S. -U.; Cicuttin, A.; Crespo, M.L.; Curiel, Q.; Dalla Torre, S.; Dasgupta, S.S.; Dasgupta, S.; Denisov, O. Yu.; Dhara, L.; Donskov, S.V.; Doshita, N.; Duic, V.; Duennweber, W.; Dziewiecki, M.; Efremov, A.; Eversheim, P.D.; Eyrich, W.; Faessler, M.; Ferrero, A.; Finger, M.; Fischer, H.; Franco, C.; von Hohenesche, N. du Fresne; Friedrich, J.M.; Frolov, V.; Fuchey, E.; Gautheron, F.; Gavrichtchouk, O.P.; Gerassimov, S.; Giordano, F.; Gnesi, I.; Gorzellik, M.; Grabmueller, S.; Grasso, A.; Grosse Perdekamp, M.; Grube, B.; Grussenmeyer, T.; Guskov, A.; Haas, F.; Hahne, D.; von Harrach, D.; Hashimoto, R.; Heinsius, F.H.; Heitz, R.; Herrmann, F.; Hinterberger, F.; Horikawa, N.; dHose, N.; Hsieh, C. -Y.; Huber, S.; Ishimoto, S.; Ivanov, A.; Ivanshin, Yu.; Iwata, T.; Jahn, R.; Jary, V.; Joosten, R.; Joerg, P.; Kabuss, E.; Ketzer, B.; Khaustov, G.V.; Khokhlov, Yu. A.; Kisselev, Yu.; Klein, F.; Klimaszewski, K.; Koivuniemi, J.H.; Kolosov, V.N.; Kondo, K.; Koenigsmann, K.; Konorov, I.; Konstantinov, V.F.; Kotzinian, A.M.; Kouznetsov, O.M.; Kuhn, R.; Kraemer, M.; Kremser, P.; Krinner, F.; Kroumchtein, Z.V.; Kulinich, Y.; Kunne, F.; Kurek, K.; Kurjata, R.P.; Lednev, A.A.; Lehmann, A.; Levillain, M.; Levorato, S.; Lichtenstadt, J.; Longo, R.; Maggiora, A.; Magnon, A.; Makins, N.; Makke, N.; Mallot, G.K.; Marchand, C.; Marianski, B.; Martin, A.; Marzec, J.; Matousek, J.; Matsuda, H.; Matsuda, T.; Meshcheryakov, G.V.; Meyer, W.; Michigami, T.; Mikhailov, Yu. V.; Mikhasenko, M.; Mitrofanov, E.; Mitrofanov, N.; Miyachi, Y.; Montuenga, P.; Nagaytsev, A.; Nerling, F.; Neyret, D.; Nikolaenko, V.I.; Novy, J.; Nowak, W.-D.; Nukazuka, G.; Nunes, A.S.; Olshevsky, A.G.; Orlov, I.; Ostrick, M.; Panzieri, D.; Parsamyan, B.; Paul, S.; Peng, J. -C.; Pereira, F.; Pesek, M.; Peshekhonov, D.V.; Pierre, N.; Platchkov, S.; Pochodzalla, J.; Polyakov, V.A.; Pretz, J.; Quaresma, M.; Quintans, C.; Ramos, S.; Regali, C.; Reicherz, G.; Riedl, C.; Roskot, M.; Ryabchikov, D.I.; Rybnikov, A.; Rychter, A.; Salac, R.; Samoylenko, V.D.; Sandacz, A.; Santos, C.; Sarkar, S.; Savin, I.A.; Sawada, T.; Sbrizzai, G.; Schiavon, P.; Schmidt, K.; Schmieden, H.; Schoenning, K.; Schopferer, S.; Seder, E.; Selyunin, A.; Shevchenko, O. Yu.; Steffen, D.; Silva, L.; Sinha, L.; Sirtl, S.; Slunecka, M.; Smolik, J.; Sozzi, F.; Srnka, A.; Stolarski, M.; Sulc, M.; Suzuki, H.; Szabelski, A.; Szameitat, T.; Sznajder, P.; Takekawa, S.; Tasevsky, M.; Tessaro, S.; Tessarotto, F.; Thibaud, F.; Tosello, F.; Tskhay, V.; Uhl, S.; Veloso, J.; Virius, M.; Vondra, J.; Weisrock, T.; Wilfert, M.; Windmolders, R.; ter Wolbeek, J.; Zaremba, K.; Zavada, P.; Zavertyaev, M.; Zemlyanichkina, E.; Ziembicki, M.; Zink, A.

2017-01-10

Multiplicities of charged pions and unidentified hadrons produced in deep-inelastic scattering were measured in bins of the Bjorken scaling variable $x$, the relative virtual-photon energy $y$ and the relative hadron energy $z$. Data were obtained by the COMPASS Collaboration using a 160 GeV muon beam and an isoscalar target ($^6$LiD). They cover the kinematic domain in the photon virtuality $Q^2$ > 1(GeV/c$)^2$, $0.004 < x < 0.4$, $0.2 < z < 0.85$ and $0.1 < y < 0.7$. In addition, a leading-order pQCD analysis was performed using the pion multiplicity results to extract quark fragmentation functions.

Sensory and physicochemical characteristics of salamis added with vegetable-based curing ingredients

Directory of Open Access Journals (Sweden)

Vicky Lilge Kawski

Full Text Available ABSTRACT: The aim of this study was to evaluate the sensory and physicochemical quality of colonial salamis added with vegetable-based curing ingredients as potential enhancers of quality products. Salamis were produced according to three treatments: (A Control: 0.1% curing salt; (B rosemary: 0.05% curing salt + 0.5% rosemary extract (RE; and (C RE+celery: 0.14% Veg 503 + 0.27% Veg 504 (sea salt plus celery, nitrate and nitrite supplies, respectively + 0.5% of RE. No significant differences were observed (P>0.05 among the three treatments for dry matter (DM, crude protein (CP, ash, ether extract (EE and gross energy (GE. Sensory analysis was performed by applying the preference test and multiple comparison between the three treatments. Salamis added with vegetable-based curing ingredients were sensory equivalent to conventional level of curing salts. Vegetable extracts allowed the development of the sensory features of salami and did not interfere in the fermentation process. Results suggested that the extracts can serve as effective natural curing ingredients for the ripening process and cured meat color as well as adequate shelf-life replacing the commercial curing salts in meat and meat products. After 30 days of ripening, salami from the control treatment (conventional levels of nitrite and nitrate and the treatments with added vegetable-based curing ingredients and low nitrite and nitrate content (RE and RE + celery were equivalent in sensory quality.

Updates on chemical and biological research on botanical ingredients in dietary supplements.

Science.gov (United States)

Pawar, Rahul S; Tamta, Hemlata; Ma, Jun; Krynitsky, Alexander J; Grundel, Erich; Wamer, Wayne G; Rader, Jeanne I

2013-05-01

Increased use of dietary supplements is a phenomenon observed worldwide. In the USA, more than 40% of the population recently reported using complementary and alternative medicines, including botanical dietary supplements. Perceptions that such dietary supplements are natural and safe, may prevent disease, may replace prescription medicines, or may make up for a poor diet, play important roles in their increased use. Toxicity of botanical dietary supplements may result from the presence of naturally occurring toxic constituents or from contamination or adulteration with pharmaceutical agents, heavy metals, mycotoxins, pesticides, or bacteria, misidentification of a plant species in a product, formation of electrophilic metabolites, organ-specific reactions, or botanical-drug interactions. The topics discussed in this review illustrate several issues in recent research on botanical ingredients in dietary supplements. These include (1) whether 1,3-dimethylamylamine is a natural constituent of rose geranium (Pelargonium graveolens), (2) how analysis of the components of dietary supplements containing bitter melon (Momordica charantia) is essential to understanding their potential biological effects, and (3) how evolving methods for in vitro studies on botanical ingredients can contribute to safety evaluations. The virtual explosion in the use of botanical ingredients in hundreds of products presents a considerable challenge to the analytical community, and the need for appropriate methods cannot be overstated. We review recent developments and use of newer and increasingly sensitive methods that can contribute to increasing the safety and quality of botanical ingredients in dietary supplements.

Inert matrix fuel in dispersion type fuel elements

Energy Technology Data Exchange (ETDEWEB)

Savchenko, A.M. [A.A. Bochvar All-Russia Research Institute of Inorganic Materials (VNIINM) 123060, P.O. Box 369, Rogova Street, 5A, Moscow (Russian Federation)]. E-mail: sav@bochvar.ru; Vatulin, A.V. [A.A. Bochvar All-Russia Research Institute of Inorganic Materials (VNIINM) 123060, P.O. Box 369, Rogova Street, 5A, Moscow (Russian Federation); Morozov, A.V. [A.A. Bochvar All-Russia Research Institute of Inorganic Materials (VNIINM) 123060, P.O. Box 369, Rogova Street, 5A, Moscow (Russian Federation); Sirotin, V.L. [A.A. Bochvar All-Russia Research Institute of Inorganic Materials (VNIINM) 123060, P.O. Box 369, Rogova Street, 5A, Moscow (Russian Federation); Dobrikova, I.V. [A.A. Bochvar All-Russia Research Institute of Inorganic Materials (VNIINM) 123060, P.O. Box 369, Rogova Street, 5A, Moscow (Russian Federation); Kulakov, G.V. [A.A. Bochvar All-Russia Research Institute of Inorganic Materials (VNIINM) 123060, P.O. Box 369, Rogova Street, 5A, Moscow (Russian Federation); Ershov, S.A. [A.A. Bochvar All-Russia Research Institute of Inorganic Materials (VNIINM) 123060, P.O. Box 369, Rogova Street, 5A, Moscow (Russian Federation); Kostomarov, V.P. [A.A. Bochvar All-Russia Research Institute of Inorganic Materials (VNIINM) 123060, P.O. Box 369, Rogova Street, 5A, Moscow (Russian Federation); Stelyuk, Y.I. [A.A. Bochvar All-Russia Research Institute of Inorganic Materials (VNIINM) 123060, P.O. Box 369, Rogova Street, 5A, Moscow (Russian Federation)

2006-06-30

The advantages of using inert matrix fuel (IMF) as a dispersion fuel in an aluminium alloy matrix are considered, in particular, low temperatures in the fuel centre, achievable high burn-ups, serviceability in transients and an environmentally friendly process of fuel rod fabrication. Two main versions of IMF are under development at A.A. Bochvar Institute, i.e. heterogeneous or isolated distribution of plutonium. The out-of-pile results on IMF loaded with uranium dioxide as plutonium simulator are presented. Fuel elements with uranium dioxide composition fabricated at A.A. Bochvar Institute are currently under MIR tests (RIAR, Dimitrovgrad). The fuel elements reached a burn-up of 88 MW d kg{sup -1} (equivalent to the burn up of the standard uranium dioxide pelletized fuel) without loss of leak-tightness of the cladding. The feasibility of fabricating IMF of these particular types with plutonium dioxide is considered with a view to in-pile irradiation.

Inert matrix fuel in dispersion type fuel elements

Science.gov (United States)

Savchenko, A. M.; Vatulin, A. V.; Morozov, A. V.; Sirotin, V. L.; Dobrikova, I. V.; Kulakov, G. V.; Ershov, S. A.; Kostomarov, V. P.; Stelyuk, Y. I.

2006-06-01

The advantages of using inert matrix fuel (IMF) as a dispersion fuel in an aluminium alloy matrix are considered, in particular, low temperatures in the fuel centre, achievable high burn-ups, serviceability in transients and an environmentally friendly process of fuel rod fabrication. Two main versions of IMF are under development at A.A. Bochvar Institute, i.e. heterogeneous or isolated distribution of plutonium. The out-of-pile results on IMF loaded with uranium dioxide as plutonium simulator are presented. Fuel elements with uranium dioxide composition fabricated at A.A. Bochvar Institute are currently under MIR tests (RIAR, Dimitrovgrad). The fuel elements reached a burn-up of 88 MW d kg-1 (equivalent to the burn up of the standard uranium dioxide pelletized fuel) without loss of leak-tightness of the cladding. The feasibility of fabricating IMF of these particular types with plutonium dioxide is considered with a view to in-pile irradiation.

Botanical supplements: detecting the transition from ingredients to supplements

Science.gov (United States)

Methods were developed using flow injection mass spectrometry (FIMS) and chemometrics for the comparison of spectral similarities and differences of 3 botanical ingredients and their supplements: Echinacea purpurea aerial samples and solid and liquid supplements, E. purpurea root samples and solid s...

Mycosporine-Like Amino Acids: Potential Health and Beauty Ingredients

Directory of Open Access Journals (Sweden)

Ewelina Chrapusta

2017-10-01

Full Text Available Human skin is constantly exposed to damaging ultraviolet radiation (UVR, which induces a number of acute and chronic disorders. To reduce the risk of UV-induced skin injury, people apply an additional external protection in the form of cosmetic products containing sunscreens. Nowadays, because of the use of some chemical filters raises a lot of controversies, research focuses on exploring novel, fully safe and highly efficient natural UV-absorbing compounds that could be used as active ingredients in sun care products. A promising alternative is the application of multifunctional mycosporine-like amino acids (MAAs, which can effectively compete with commercially available filters. Here, we outline a complete characterization of these compounds and discuss their enormous biotechnological potential with special emphasis on their use as sunscreens, activators of cells proliferation, anti-cancer agents, anti-photoaging molecules, stimulators of skin renewal, and functional ingredients of UV-protective biomaterials.

Mycosporine-Like Amino Acids: Potential Health and Beauty Ingredients

Science.gov (United States)

Chrapusta, Ewelina; Kaminski, Ariel; Duchnik, Kornelia; Bober, Beata; Adamski, Michal; Bialczyk, Jan

2017-01-01

Human skin is constantly exposed to damaging ultraviolet radiation (UVR), which induces a number of acute and chronic disorders. To reduce the risk of UV-induced skin injury, people apply an additional external protection in the form of cosmetic products containing sunscreens. Nowadays, because of the use of some chemical filters raises a lot of controversies, research focuses on exploring novel, fully safe and highly efficient natural UV-absorbing compounds that could be used as active ingredients in sun care products. A promising alternative is the application of multifunctional mycosporine-like amino acids (MAAs), which can effectively compete with commercially available filters. Here, we outline a complete characterization of these compounds and discuss their enormous biotechnological potential with special emphasis on their use as sunscreens, activators of cells proliferation, anti-cancer agents, anti-photoaging molecules, stimulators of skin renewal, and functional ingredients of UV-protective biomaterials. PMID:29065484

Assessment of the unidentified organic matter fraction in fogwater using fluorescence spectroscopy

Science.gov (United States)

Valsaraj, K.; Birdwell, J.

2010-07-01

Dissolved organic matter (DOM) in fogwaters from southeastern Louisiana and central-eastern China has been characterized using excitation-emission matrix (EEM) fluorescence spectroscopy. The results demonstrate that fluorescence spectroscopy can be used to obtain a qualitative assessment of the large fraction of fogwater organic carbon (~40 - 80% by weight) that cannot be identified in terms of specific chemical compounds. The method has the principle advantage that it can be applied at natural abundance concentrations, thus eliminating the need for large sample volumes required to isolate DOM for characterization by other spectroscopic (NMR, FTIR) and chemical (elemental) analyses. It was anticipated that the fogwater organic matter fluorescence spectra would resemble those of surface and rain waters, containing peaks indicative of both humic substances and fluorescent amino acids. Humic- and protein-like fluorophores were observed in the fogwater spectra and fluorescence-derived indices had values comparable to other natural waters. Biological character (intensity of tyrosine and tryptophan peaks) was found to increase with organic carbon concentration. Fogwater organic matter appears to contain a mixture of terrestrially- and microbially-derived material. The fluorescence results show that most of the unidentified fogwater organic carbon can be represented by humic-like and biologically-derived substances similar to those present in other aquatic systems.

Determination of hydrogen in uranium-niobium-zirconium alloy by inert-gas fusion

International Nuclear Information System (INIS)

Carden, W.F.

1979-12-01

An improved method has been developed using inert-gas fusion for determining the hydrogen content in uranium-niobium-zirconium (U-7.5Nb-2.5Zr) alloy. The method is applicable to concentrations of hydrogen ranging from 1 to 250 micrograms per gram and may be adjusted for analysis of greater hydrogen concentrations. Hydrogen is determined using a hydrogen determinator. The limit of error for a single determination at the 95%-confidence level (at the 3.7-μg/g-hydrogen level) is +-1.4 micrograms per gram hydrogen

Allowable spent LWR fuel storage temperatures in inert gases, nitrogen, and air

International Nuclear Information System (INIS)

Gilbert, E.R.; Cunningham, M.E.; Simonen, E.P.; Thomas, L.E.; Campbell, T.K.; Barnhart, D.M.

1990-01-01

Spent fuel in inert dry storage is now a reality in the US; recommended maximum temperature-time conditions are specified in an IBM PC-compatible code. However, spent fuel cannot yet be stored in air because the data and theory needed for predicting allowable temperatures are still being developed. Tests to determine the behavior of spent UO 2 fragments and breached rod specimens in air are providing data that will be used to determine the temperatures that can be allowed for fuel stored in air. 13 refs., 5 figs

Optimal dual-fuel propulsion for minimum inert weight or minimum fuel cost

Science.gov (United States)

Martin, J. A.

1973-01-01

An analytical investigation of single-stage vehicles with multiple propulsion phases has been conducted with the phasing optimized to minimize a general cost function. Some results are presented for linearized sizing relationships which indicate that single-stage-to-orbit, dual-fuel rocket vehicles can have lower inert weight than similar single-fuel rocket vehicles and that the advantage of dual-fuel vehicles can be increased if a dual-fuel engine is developed. The results also indicate that the optimum split can vary considerably with the choice of cost function to be minimized.

Investigation of the cosmetic ingredient distribution in the stratum corneum using NanoSIMS imaging

International Nuclear Information System (INIS)

Tanji, N.; Okamoto, M.; Katayama, Y.; Hosokawa, M.; Takahata, N.; Sano, Y.

2008-01-01

In order to understand the mechanisms of action of cosmetic ingredients, it is important to establish the distribution of the component agents within the epidermis of the skin. To date, time-of-flight secondary ion mass spectrometry (TOF-SIMS) has been used to detect cosmetic ingredients in the skin. However, it is technically difficult to investigate the distribution of the agents in the stratum corneum using TOF-SIMS. Therefore, an analytical method with higher spatial resolution is required. In this study, we investigated an imaging analysis technique based on NanoSIMS to detect cosmetic ingredients in the skin. Pig skin was used as a model for human skin. The sample was treated with a cosmetic formulation containing 15 N-labelled pseudo-ceramide (SLE). The sample was frozen with liquid nitrogen and cross-sections were cut using a cryomicrotome. As a result, the fine layer structure of the corneocytes was clearly observed by using NanoSIMS. Our studies indicate that SLE penetrates into the stratum corneum via an intercellular route. We conclude that application of NanoSIMS analysis can contribute to a better understanding of the function of cosmetic ingredients in the skin.

78 FR 55641 - Polyurethane-Type Polymers; Tolerance Exemption

Science.gov (United States)

2013-09-11

...-Type Polymers; Tolerance Exemption AGENCY: Environmental Protection Agency (EPA). ACTION: Final rule... polymers produced by the reaction of either 1,6-hexanediisocyanate; 2,4,4-trimethyl-1,6-hexanediisocyanate... (also known as polyurethane-type polymers), when used as an inert ingredient in a pesticide chemical...

Characterizing the microstructural basis of “unidentified bright objects” in neurofibromatosis type 1 : A combined in vivo multicomponent T2 relaxation and multi-shell diffusion MRI analysis

NARCIS (Netherlands)

Billiet, T.; Mädler, B.; D'Arco, F.; Deprez, S.; Plasschaert, E.; Leemans, A.; Zhang, H.; Van Den Bergh, B.R.H.; Vandenbulcke, M.; Legius, E.; Sunaert, S.; Emsell, L.

2014-01-01

Introduction The histopathological basis of “unidentified bright objects” (UBOs) (hyperintense regions seen on T2-weighted magnetic resonance (MR) brain scans in neurofibromatosis-1 (NF1)) remains unclear. New in vivo MRI-based techniques (multi-exponential T2 relaxation (MET2) and diffusion MR

Effects of tailoring ingredients in auditory persuasive health messages on fruit and vegetable intake

OpenAIRE

Elbert, Sarah P.; Dijkstra, Arie; Rozema, Andrea

2017-01-01

Objective: Health messages can be tailored by applying different tailoring ingredients, among which personalisation, feedback and adaptation. This experiment investigated the separate effects of these tailoring ingredients on behaviour in auditory health persuasion. Furthermore, the moderating effect of self-efficacy was assessed.Design: The between-participants design consisted of four conditions. A generic health message served as a control condition; personalisation was applied using the r...

Rapid classification of pharmaceutical ingredients with Raman spectroscopy using compressive detection strategy with PLS-DA multivariate filters.

Science.gov (United States)

Cebeci Maltaş, Derya; Kwok, Kaho; Wang, Ping; Taylor, Lynne S; Ben-Amotz, Dor

2013-06-01

Identifying pharmaceutical ingredients is a routine procedure required during industrial manufacturing. Here we show that a recently developed Raman compressive detection strategy can be employed to classify various widely used pharmaceutical materials using a hybrid supervised/unsupervised strategy in which only two ingredients are used for training and yet six other ingredients can also be distinguished. More specifically, our liquid crystal spatial light modulator (LC-SLM) based compressive detection instrument is trained using only the active ingredient, tadalafil, and the excipient, lactose, but is tested using these and various other excipients; microcrystalline cellulose, magnesium stearate, titanium (IV) oxide, talc, sodium lauryl sulfate and hydroxypropyl cellulose. Partial least squares discriminant analysis (PLS-DA) is used to generate the compressive detection filters necessary for fast chemical classification. Although the filters used in this study are trained on only lactose and tadalafil, we show that all the pharmaceutical ingredients mentioned above can be differentiated and classified using PLS-DA compressive detection filters with an accumulation time of 10ms per filter. Copyright © 2013 Elsevier B.V. All rights reserved.

Direct and simultaneous detection of organic and inorganic ingredients in herbal powder preparations by Fourier transform infrared microspectroscopic imaging.

Science.gov (United States)

Chen, Jian-Bo; Sun, Su-Qin; Tang, Xu-Dong; Zhang, Jing-Zhao; Zhou, Qun

2016-08-05

Herbal powder preparation is a kind of widely-used herbal product in the form of powder mixture of herbal ingredients. Identification of herbal ingredients is the first and foremost step in assuring the quality, safety and efficacy of herbal powder preparations. In this research, Fourier transform infrared (FT-IR) microspectroscopic identification method is proposed for the direct and simultaneous recognition of multiple organic and inorganic ingredients in herbal powder preparations. First, the reference spectrum of characteristic particles of each herbal ingredient is assigned according to FT-IR results and other available information. Next, a statistical correlation threshold is determined as the lower limit of correlation coefficients between the reference spectrum and a larger number of calibration characteristic particles. After validation, the reference spectrum and correlation threshold can be used to identify herbal ingredient in mixture preparations. A herbal ingredient is supposed to be present if correlation coefficients between the reference spectrum and some sample particles are above the threshold. Using this method, all kinds of herbal materials in powder preparation Kouqiang Kuiyang San are identified successfully. This research shows the potential of FT-IR microspectroscopic identification method for the accurate and quick identification of ingredients in herbal powder preparations. Copyright © 2016 Elsevier B.V. All rights reserved.

Dissolved helium, inert gases, radium and radon in groundwaters from the Altnabreac research site

International Nuclear Information System (INIS)

Andrews, J.N.; Kay, R.L.F.

1985-01-01

A groundwater geochemical study has been carried out at Altnabreac, Cenithness, Scotland, to investigate the feasibility of disposal of high-level radioactive wastes in crystalline rock. A groundwater flow model was constructed for sampling a section at depths up to 300 m. Measurements of inert gases dissolved in groundwaters are used, with parallel measurements of 14 C, tritium, oxygen and hydrogen isotopes to infer groundwater ages and residence times. (UK)

Control characteristics of inert gas recovery plant

International Nuclear Information System (INIS)

Mikawa, Hiroji; Kato, Yomei; Kamiya, Kunio

1980-01-01

This paper presents a dynamic simulator and the control characteristics for a radioactive inert gas recovery plant which uses a cryogenic liquefying process. The simulator was developed to analyze the operational characteristics and is applicable to gas streams which contain nitrogen, argon, oxygen and krypton. The characteristics analysis of the pilot plant was performed after the accuracy of the simulator was checked using data obtained in fundamental experiments. The relationship between the reflux ratio and krypton concentration in the effluent gas was obtained. The decontamination factor is larger than 10 9 when the reflux ratio is more than 2. 0. The control characteristics of the plant were examined by changing its various parameters. These included the amount of gas to be treated, the heater power inside the evaporator and the liquid nitrogen level in the condenser. These characteristics agreed well with the values obtained in the pilot plant. The results show that the krypton concentration in the effluent gas increases when the liquid nitrogen level is decreased. However, in this case, the krypton concentration can be minimized by applying a feed forward control to the evaporator liquid level controller. (author)

Mn nanoparticles produced by inert gas condensation

International Nuclear Information System (INIS)

Ward, M B; Brydson, R; Cochrane, R F

2006-01-01

The results from experiments using the inert gas condensation method to produce nanoparticles of manganese are presented. Structural and compositional data have been collected through electron diffraction, EDX (energy dispersive X-ray) and EELS (electron energy loss spectroscopy). Both Mn 3 O 4 and pure Mn particles have been produced. Moisture in untreated helium gas causes the particles to oxidize, whereas running the helium through a liquid nitrogen trap removes the moisture and produces β-Mn particles in a metastable state. The particle sizes and the size distribution have been determined. Particle sizes range from 2nm to above 100 nm, however the majority of particles lie in the range below 20 nm with a modal particle size of 6 nm. As well as the modal particle size of 6 nm, there is another peak in the frequency curve at 16 nm that represents another group particles that lie in the range 12 to 20 nm. The smaller particles are single crystals, but the larger particles appear to have a dense region around their edge with a less dense centre. Determination of their exact nature is ongoing

How to Successfully Build a Clear Label Paradigm : Ingredient Marketing

NARCIS (Netherlands)

Diaz, J.

2016-01-01

Careful labeling and consumer education may make the difference for the future success of individual ingredients and the products that rely on them. The second of a two-part report on a clear label strategy.

Nutritive Value and Availability of Commonly Used Feed Ingredients ...

African Journals Online (AJOL)

Commonly utilized feed ingredients for culture of Nile tilapia (Oreochromis niloticus) and African catfish (Clarias gariepinus) from Kenya, Tanzania and Rwanda were collected over a period of six months (January - June 2010) and evaluated for their nutritive composition through proximate analysis. Most of the fish feed ...

Apparent digestibility of nutrients and energy of conventional ingredients for the silver mojarra, Diapterus rhombeus

Directory of Open Access Journals (Sweden)

Francisco Oliveira de Magalhães Júnior

2016-06-01

Full Text Available Knowledge on the nutritional value of feed ingredient is an important step in the formulation of diets in order to maximize animal productivity. Thus a study was conducted to determine the apparent digestibility coefficients (ADC of dry matter (ADCDM, crude protein (ADCCP, gross energy (ADCGE and amino acids (ADCAA of conventional feed ingredients for juvenile silver mojarra (13.0 ± 3.23 g. The study was conducted in the laboratory for nutrition and feeding of fish (AQUANUT, using 80 silver mojarra collected in nature, which were kept in digestibility aquaria for a period of 21 days. The following ingredients were evaluated: fish meal, soybean meal, corn meal, corn gluten meal, rice bran, wheat bran and starch, which substituted 30% of a reference pelletized diet with 325.00 g kg-1 crude protein and 3,692 Kcal kg-1 gross energy. Additionally 1.0 g kg-1 chrome oxide was added to each diet as a marker. The excreta were obtained using three repetitions for each tested ingredient, which were dried for further analyses. The soybean meal showed the best ADCDM value (67.45%, followed by the other ingredients. There was no significant difference between the soybean meal (95.16%, fish meal (92.97% and the corn meal (91.90% for the best ADCCP coefficients. The ADCGE for soybean meal and maize meal were 65.23% and 60.31%, respectively, followed by fish meal (51.85%. The results demonstrate that silver mojarra can digest animal protein as well as that of vegetal origin. Silver mojarra can also efficiently digest and absorb some of the main amino acids of fish, such as lysine, methionine and threonine, from the same studied ingredients.

[The coordination of the forensic medical service with the medical criminology subdivisions of internal affairs organs in the personal identification of unidentified corpses].

Science.gov (United States)

Pashinian, G A; Tuchik, E S

1997-01-01

In order to improve the cooperation between medical criminology departments of the organs of home affairs and forensic medical service in personality identification of unidentified corpses, the authors propose amendments to the routine procedure regulated by documents of the Ministry of Home Affairs of the Russian Federation, for these documents are in need of serious correction and revision, so that they conform to the judicial legislation and other documents.

Muon implantation in inert gases studied by radio frequency spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Johnson, C [ISIS Facility, CCLRC Rutherford Appleton Laboratory, Chilton, Didcot, Oxfordshire (United Kingdom); Cottrell, S P [ISIS Facility, CCLRC Rutherford Appleton Laboratory, Chilton, Didcot, Oxfordshire (United Kingdom); Ghandi, K [TRIUMF and Department of Chemistry, University of British Columbia, Vancouver (Canada); Fleming, D G [TRIUMF and Department of Chemistry, University of British Columbia, Vancouver (Canada)

2005-01-14

Diamagnetic and muonium (Mu) fractions formed in low-pressure inert gases, by energetic muon implantation, have been studied using the technique of time-delayed radio frequency muon spin resonance (RF-{mu}SR). Results obtained establish the validity of the long-held view that formation of these species is due only to prompt processes, and in turn confirms that the diamagnetic environment is due to a muon molecular ion, MMu{sup +}, and not a bare {mu}{sup +}. In addition, polarization fractions for the diamagnetic and Mu environments have been determined at different pressures, thereby complementing earlier data, and demonstrating that the RF-{mu}SR technique provides polarization fractions in good accord with those obtained using conventional transverse-field muon spin resonance measurements.

Evaluation of antioxidant capacity of Chinese five-spice ingredients.

Science.gov (United States)

Bi, Xinyan; Soong, Yean Yean; Lim, Siang Wee; Henry, Christiani Jeyakumar

2015-05-01

Phenolic compounds in spices were reportedly found to possess high antioxidant capacities (AOCs), which may prevent or reduce risk of human diseases such as cardiovascular disease, cancer and diabetes. The potential AOC of Chinese five-spice powder (consist of Szechuan pepper, fennel seed, cinnamon, star anise and clove) with varying proportion of individual spice ingredients was investigated through four standard methods. Our results suggest that clove is the major contributor to the AOC of the five-spice powder whereas the other four ingredients contribute to the flavour. For example, the total phenolic content as well as ferric reducing antioxidant power (FRAP), Trolox equivalent antioxidant capacity (TEAC) and oxygen radical absorbance capacity (ORAC) values increased linearly with the clove percentage in five-spice powder. This observation opens the door to use clove in other spice mixtures to increase their AOC and flavour. Moreover, linear relationships were also observed between AOC and the total phenolic content of the 32 tested spice samples.

Consumers’ response to genetically modified ingredients in processed food in an emerging economy

DEFF Research Database (Denmark)

Yormirzoev, Mirzobobo; Teuber, Ramona

2017-01-01

Genetically modified (GM) foods are available in many countries including post–Soviet Union countries. However, empirical evidence on consumer acceptance for this region is scarce. In this study, we investigate consumers’ willingness to purchase a processed food containing GM ingredients. For thi......Genetically modified (GM) foods are available in many countries including post–Soviet Union countries. However, empirical evidence on consumer acceptance for this region is scarce. In this study, we investigate consumers’ willingness to purchase a processed food containing GM ingredients...

A method for making an inert porous electrode for a chemical current source

Energy Technology Data Exchange (ETDEWEB)

Ksenzhek, O.S.; Litvinova, V.I.; Martynenko, T.L.; Raykhelson, L.B.; Shembel, Ye.M.; Sokolov, L.A.

1983-01-01

A method is proposed for making an inert, porous electrode for chemical current sources (KhIT) with a nonaqueous electrolyte on the basis of aprotonic solvents and an active cathode substance which is dissolved in the electrolyte. The method includes preparing an electrode mass from the starting material and subsequent formation of the electrode. To increase the energy capacity, after formation, the electrode is subjected to electrochemical anode polarization to potentials which correspond to the potential of electrochemical breakdown of the background electrolyte.

Analysis of air-, moisture- and solvent-sensitive chemical compounds by mass spectrometry using an inert atmospheric pressure solids analysis probe.

Science.gov (United States)

Mosely, Jackie A; Stokes, Peter; Parker, David; Dyer, Philip W; Messinis, Antonis M

2018-02-01

A novel method has been developed that enables chemical compounds to be transferred from an inert atmosphere glove box and into the atmospheric pressure ion source of a mass spectrometer whilst retaining a controlled chemical environment. This innovative method is simple and cheap to implement on some commercially available mass spectrometers. We have termed this approach inert atmospheric pressure solids analysis probe ( iASAP) and demonstrate the benefit of this methodology for two air-/moisture-sensitive chemical compounds whose characterisation by mass spectrometry is now possible and easily achieved. The simplicity of the design means that moving between iASAP and standard ASAP is straightforward and quick, providing a highly flexible platform with rapid sample turnaround.

Occurrence of Clostridium perfringens contamination in poultry feed ingredients: Isolation, identification and its antibiotic sensitivity pattern

Directory of Open Access Journals (Sweden)

Shanmugasundaram Udhayavel

2017-09-01

Full Text Available This work has been undertaken to study the occurrence of Clostridium perfringens contamination in the poultry feed ingredients and find out its in-vitro antibiotic sensitivity pattern to various antimicrobial drugs. Two hundred and ninety-eight poultry feed ingredient samples received at Poultry Disease Diagnosis and Surveillance Laboratory, Namakkal, Tamil Nadu in South India were screened for the presence of C. perfringens. The organisms were isolated in Perfringens agar under anaerobic condition and subjected to standard biochemical tests for confirmation. In vitro antibiogram assay has been carried out to determine the sensitivity pattern of the isolates to various antimicrobial drugs. One hundred and one isolates of C. perfringens were obtained from a total of 298 poultry feed ingredient samples. Overall positivity of 33.89% could be made from the poultry feed ingredients. Highest level of C. perfringens contamination was detected in fish meal followed by bone meal, meat and bone meal and dry fish. Antibiogram assay indicated that the organisms are highly sensitive to gentamicin (100%, chlortetracycline (96.67%, gatifloxacin (93.33%, ciprofloxacin (86.67%, ofloxacin (86.67% and lincomycin (86.67%. All the isolates were resistant to penicillin-G. Feed ingredients rich in animal proteins are the major source of C. perfringens contamination.

Collider and dark matter searches in the inert doublet model from Peccei-Quinn symmetry

Energy Technology Data Exchange (ETDEWEB)

Alves, Alexandre [Departamento de Ciências Exatas e da Terra, Universidade Federal de São Paulo,Diadema-SP, 09972-270 (Brazil); Camargo, Daniel A.; Dias, Alex G. [Universidade Federal do ABC, Centro de Ciências Naturais e Humanas,09210-580, Santo André-SP (Brazil); Longas, Robinson [Instituto de Física, Universidad de Antioquia,Calle 70 No. 52-21, Medellín (Colombia); Nishi, Celso C. [Universidade Federal do ABC, Centro de Matemática, Computação e Cognição Naturais,09210-580, Santo André-SP (Brazil); Queiroz, Farinaldo S. [Max-Planck-Institut fur Kernphysik,Saupfercheckweg 1, 69117 Heidelberg (Germany)

2016-10-04

Weakly Interacting Massive Particles (WIMPs) and axions are arguably the most compelling dark matter candidates in the literature. Could they coexist as dark matter particles? More importantly, can they be incorporated in a well motivated framework in agreement with experimental data? In this work, we show that this two component dark matter can be realized in the Inert Doublet Model in an elegant and natural manner by virtue of the spontaneous breaking of a Peccei-Quinn U(1){sub PQ} symmetry into a residual ℤ{sub 2} symmetry. The WIMP stability is guaranteed by the ℤ{sub 2} symmetry and a new dark matter component, the axion, arises. There are two interesting outcomes: (i) vector-like quarks needed to implement the Peccei-Quinn symmetry in the model may act as a portal between the dark sector and the SM fields with a supersymmetry-type phenomenology at colliders; (ii) two-component Inert Doublet Model re-opens the phenomenologically interesting 100–500 GeV mass region. We show that the model can successfully realize a two component dark matter framework and at the same time avoid low and high energy physics constraints such as monojet and dijet plus missing energy, as well as indirect and direct dark matter detection bounds.

An Inert Continuous Microreactor for the Isolation and Analysis of a Single Microbial Cell

Directory of Open Access Journals (Sweden)

Katrin Rosenthal

2015-11-01

Full Text Available Studying biological phenomena of individual cells is enabled by matching the scales of microbes and cultivation devices. We present a versatile, chemically inert microfluidic lab-on-a-chip (LOC device for biological and chemical analyses of isolated microorganisms. It is based on the Envirostat concept and guarantees constant environmental conditions. A new manufacturing process for direct fusion bonding chips with functional microelectrodes for selective and gentle cell manipulation via negative dielectrophoresis (nDEP was generated. The resulting LOC system offered a defined surface chemistry and exceptional operational stability, maintaining its structural integrity even after harsh chemical treatment. The microelectrode structures remained fully functional after thermal bonding and were proven to be efficient for single-cell trapping via nDEP. The microfluidic network consisted solely of glass, which led to enhanced chip reusability and minimized interaction of the material with chemical and biological compounds. We validated the LOC for single-cell studies with the amino acid secreting bacterium Corynebacterium glutamicum. Intracellular l-lysine production dynamics of individual bacteria were monitored based on a genetically encoded fluorescent nanosensor. The results demonstrate the applicability of the presented LOC for pioneering chemical and biological studies, where robustness and chemically inert surfaces are crucial parameters for approaching fundamental biological questions at a single-cell level.

[Research advance in metabolism of effective ingredients from traditional Chinese medicines by probiotics].

Science.gov (United States)

Dai, Cheng-En; Li, Hai-Long; He, Xiao-Ping; Zheng, Fen-Fen; Zhu, Hua-Liu; Liu, Liang-Feng; Du, Wei

2018-01-01

The pharmacological activity of active ingredients from Chinese medicine depends greatly on the microecological environment of probiotics in the human body. After effective ingredients from traditional Chinese medicines are metabolized or biotransformed by probiotics, their metabolites can increase pharmacological activity, and can be absorbed more easily to improve the bioavailability. Therefore, the combination of Chinese medicines with probiotics is the innovation point in R&D of functional food and Chinese medicines, and also a new thinking for the modernization of Chinese medicine.This review summarizes and analyses the research progress on metabolism effects of gut microbiota on Chinese medicines components, the regulating effect of effective ingredients from Chinese medicine on intestinal probiotics, the application status of probiotics in traditional Chinese medicines, and the main problems and prospects in the research and development of Chinese medicines products with probiotic, aiming to provide theoretical guidance and practical value for the fermentation engineering of Chinese herbal medicine. Copyright© by the Chinese Pharmaceutical Association.

Applicability of in silico genotoxicity models on food and feed ingredients.

Science.gov (United States)

Vuorinen, Anna; Bellion, Phillip; Beilstein, Paul

2017-11-01

Evaluation of the genotoxic potential of food and feed ingredients is required in the development of new substances and for their registration. In addition to in vitro and in vivo assays, in silico tools such as expert alert-based and statistical models can be used for data generation. These in silico models are commonly used among the pharmaceutical industry, whereas the food industry has not widely adopted them. In this study, the applicability of in silico tools for predicting genotoxicity was evaluated, with a focus on bacterial mutagenicity, in vitro and in vivo chromosome damage assays. For this purpose, a test set of 27 food and feed ingredients including vitamins, carotenoids, and nutraceuticals with experimental genotoxicity data was constructed from proprietary data. This dataset was run through multiple models and the model applicability was analyzed. The compounds were generally within the applicability domain of the models and the models predicted the compounds correctly in most of the cases. Although the regulatory acceptance of in silico tools as single data source is still limited, the models are applicable and can be used in the safety evaluation of food and feed ingredients. Copyright © 2017 Elsevier Inc. All rights reserved.

Replacement of moist ingredients in the feed training of carnivorous fish

Directory of Open Access Journals (Sweden)

Ana Lúcia Salaro

2012-10-01

Full Text Available The study evaluated the replacement of bovine heart by gelatin in the feed training of carnivorous fish, using giant trahira (Hoplias lacerdae as an experimental model. A completely randomized design with four treatments and five repetitions was employed. The treatments were composed of wet ingredients beef heart (control, gelatin diluted in water, gelatin diluted in beef heart broth, and gelatin diluted in water mixed with fish meal. The fish (3.22±0.03 cm and 0.57±0.01 g were conditioned to accept industrialized diets by the technique of gradual feed ingredients transition in the diet. Gains in weight and length, efficiency of feed training, specific growth rate, cannibalism, mortality and survival rates were evaluated. There was significant difference in weight and length gains and specific growth rate, whereby the use of bovine heart gave the best results. Greater efficiency of feed training was observed for fish fed diets containing beef heart and gelatin diluted in water mixed with fish meal. The high survival rates and the absence of significant differences among treatments for rates of cannibalism, mortality and survival indicate the feasibility of using gelatin as a moist ingredient in the feed training of carnivorous fish.

Effect of composition on thermal conductivity of MgO–Nd2Zr2O7 composites for inert matrix materials

International Nuclear Information System (INIS)

Nelson, A.T.; Giachino, M.M.; Nino, J.C.; McClellan, K.J.

2014-01-01

Inert matrix fuels based on magnesium oxide (MgO) as the inert phase have been of historic interest due to its high thermal conductivity. Minor actinide-bearing phases possessing an A 2 B 2 O 7 pyrochlore structure are also believed to contain a range of favorable attributes, suggesting a possible pairing with MgO to yield a high performance inert matrix fuel. The thermal diffusivity, heat capacity, and thermal expansion of MgO–Nd 2 Zr 2 O 7 composites were measured from room temperature to 1273 K, where the MgO phase content was varied from 40 to 70 volume percent. The thermal conductivity of each composition was calculated using these results and then compared to widely employed methods to approximate the thermal conductivity of composite materials based upon the properties of the constituent phases. Results suggest that use of either a rule of mixtures or geometric mean approximation for the thermal conductivity of composite systems such as this one would be subject to significant uncertainties when the constituent properties widely differ. A sigmoidal average of the upper and lower Hashin–Shtrikman bounds was found to be in good agreement with the thermal conductivity of the composites as determined experimentally

Cinnamon: Mystic powers of a minute ingredient

OpenAIRE

Pallavi Kawatra; Rathai Rajagopalan

2015-01-01

Cinnamon, due to its exotic flavor and aroma, is a key ingredient in the kitchen of every household. From the beginning of its use in 2800 BC by our ancestors for various purposes such as anointment, embalming and various ailments, it has instigated the interest of many researchers. Recently many trials have explored the beneficial effects of cinnamon in Parkinsons, diabetes, blood, and brain. After extensive research on PubMed and Google scholar, data were collected regarding its antioxidant...

Perceived fit of different combinations of carriers and functional ingredients and its effect on purchase intention

DEFF Research Database (Denmark)

Krutulyte, Rasa; Grunert, Klaus G.; Scholderer, Joachim

2011-01-01

ingredients are accepted by consumers in selected food product categories such as yoghurt, muesli bars, fish balls, tuna salad, baby meals, rye bread and bacon liver pâté. Intentions to purchase different carrier/ingredient combinations are explained by perceived fit of a particular carrier...

75 FR 22234 - Phosphate Ester, Tallowamine, Ethoxylated; Exemption from the Requirement of a Tolerance

Science.gov (United States)

2010-04-28

...) parameters were observed. The gestation index was decreased primarily due to mortality of females. Decreased... surrogate information to derive upper bound exposure estimates for the subject inert ingredient. Upper bound... highest tolerance level from the surrogate pesticides for every food, and 100% crop treated is assumed for...

Characterization of previously unidentified lunar pyroclastic deposits using Lunar Reconnaissance Orbiter Camera (LROC) data

Science.gov (United States)

Gustafson, J. Olaf; Bell, James F.; Gaddis, Lisa R.R.; Hawke, B. Ray Ray; Giguere, Thomas A.

2012-01-01

We used a Lunar Reconnaissance Orbiter Camera (LROC) global monochrome Wide-angle Camera (WAC) mosaic to conduct a survey of the Moon to search for previously unidentified pyroclastic deposits. Promising locations were examined in detail using LROC multispectral WAC mosaics, high-resolution LROC Narrow Angle Camera (NAC) images, and Clementine multispectral (ultraviolet-visible or UVVIS) data. Out of 47 potential deposits chosen for closer examination, 12 were selected as probable newly identified pyroclastic deposits. Potential pyroclastic deposits were generally found in settings similar to previously identified deposits, including areas within or near mare deposits adjacent to highlands, within floor-fractured craters, and along fissures in mare deposits. However, a significant new finding is the discovery of localized pyroclastic deposits within floor-fractured craters Anderson E and F on the lunar farside, isolated from other known similar deposits. Our search confirms that most major regional and localized low-albedo pyroclastic deposits have been identified on the Moon down to ~100 m/pix resolution, and that additional newly identified deposits are likely to be either isolated small deposits or additional portions of discontinuous, patchy deposits.

Comprehensive genetic analysis of early host body reactions to the bioactive and bio-inert porous scaffolds.

Directory of Open Access Journals (Sweden)

Tomo Ehashi

Full Text Available To design scaffolds for tissue regeneration, details of the host body reaction to the scaffolds must be studied. Host body reactions have been investigated mainly by immunohistological observations for a long time. Despite of recent dramatic development in genetic analysis technologies, genetically comprehensive changes in host body reactions are hardly studied. There is no information about host body reactions that can predict successful tissue regeneration in the future. In the present study, porous polyethylene scaffolds were coated with bioactive collagen or bio-inert poly(2-methacryloyloxyethyl phosphorylcholine-co-n-butyl methacrylate (PMB and were implanted subcutaneously and compared the host body reaction to those substrates by normalizing the result using control non-coat polyethylene scaffold. The comprehensive analyses of early host body reactions to the scaffolds were carried out using a DNA microarray assay. Within numerous genes which were expressed differently among these scaffolds, particular genes related to inflammation, wound healing, and angiogenesis were focused upon. Interleukin (IL-1β and IL-10 are important cytokines in tissue responses to biomaterials because IL-1β promotes both inflammation and wound healing and IL-10 suppresses both of them. IL-1β was up-regulated in the collagen-coated scaffold. Collagen-specifically up-regulated genes contained both M1- and M2-macrophage-related genes. Marked vessel formation in the collagen-coated scaffold was occurred in accordance with the up-regulation of many angiogenesis-inducible factors. The DNA microarray assay provided global information regarding the host body reaction. Interestingly, several up-regulated genes were detected even on the very bio-inert PMB-coated surfaces and those genes include inflammation-suppressive and wound healing-suppressive IL-10, suggesting that not only active tissue response but also the inert response may relates to these genetic

Comprehensive Genetic Analysis of Early Host Body Reactions to the Bioactive and Bio-Inert Porous Scaffolds

Science.gov (United States)

Ehashi, Tomo; Takemura, Taro; Hanagata, Nobutaka; Minowa, Takashi; Kobayashi, Hisatoshi; Ishihara, Kazuhiko; Yamaoka, Tetsuji

2014-01-01

To design scaffolds for tissue regeneration, details of the host body reaction to the scaffolds must be studied. Host body reactions have been investigated mainly by immunohistological observations for a long time. Despite of recent dramatic development in genetic analysis technologies, genetically comprehensive changes in host body reactions are hardly studied. There is no information about host body reactions that can predict successful tissue regeneration in the future. In the present study, porous polyethylene scaffolds were coated with bioactive collagen or bio-inert poly(2-methacryloyloxyethyl phosphorylcholine-co-n-butyl methacrylate) (PMB) and were implanted subcutaneously and compared the host body reaction to those substrates by normalizing the result using control non-coat polyethylene scaffold. The comprehensive analyses of early host body reactions to the scaffolds were carried out using a DNA microarray assay. Within numerous genes which were expressed differently among these scaffolds, particular genes related to inflammation, wound healing, and angiogenesis were focused upon. Interleukin (IL)-1β and IL-10 are important cytokines in tissue responses to biomaterials because IL-1β promotes both inflammation and wound healing and IL-10 suppresses both of them. IL-1β was up-regulated in the collagen-coated scaffold. Collagen-specifically up-regulated genes contained both M1- and M2-macrophage-related genes. Marked vessel formation in the collagen-coated scaffold was occurred in accordance with the up-regulation of many angiogenesis-inducible factors. The DNA microarray assay provided global information regarding the host body reaction. Interestingly, several up-regulated genes were detected even on the very bio-inert PMB-coated surfaces and those genes include inflammation-suppressive and wound healing-suppressive IL-10, suggesting that not only active tissue response but also the inert response may relates to these genetic regulations. PMID:24454803

Pulmonary distribution of [sup 99m]Tc-technegas; A comparative study of radioactive inert gases

Energy Technology Data Exchange (ETDEWEB)

Kawakami, Kenji; Shimada, Takao; Mori, Yutaka; Goto, Eisuke; Hirasawa, Yukinori [Jikei Univ., Tokyo (Japan). School of Medicine; Tominaga, Shigeru

1992-10-01

Technetium 99m-technegas ([sup 99m]Tc-gas), which consists of fine particles, is produced in carbon crucibles burned at 2500degC. In this study, the particle size of [sup 99m]Tc-gas was measured and the pulmonary distribution of [sup 99m]Tc-gas was assessed in 28 patients with various pulmonary diseases. Most particles were 5[approx]30 nm in diameter as determined by electron microscopy. In a clinical study, about 37 MBq of [sup 99m]Tc-gas was inhaled three times during deep breathing in a sitting position. In a comparative study with radioactive inert gases ([sup 133]Xe, [sup 81m]Kr), [sup 99m]Tc-gas showed a similar distribution to the inert gas in most patients, although some with obstructive disease showed hot spots in the lung fields. In patients with severe obstructive change, marked deposits of [sup 99m]Tc-gas was noted in the central airways, but [sup 99m]Tc-gas penetrated to the peripheral lung field. This result suggests that [sup 99m]Tc-gas can be used to evaluate ventilatory function even in patients with chronic obstructive pulmonary diseases. (author).

Chemical identities of radioiodine released from U3O8 in oxygen and inert gas atmospheres

International Nuclear Information System (INIS)

Tachikawa, E.; Nakashima, M.

1977-01-01

Irradiated U 3 O 8 was heated from room temperature to 1100 0 C in a temperature-programmed oven (5 0 C/min) in a flow of carrier gas. The iodine released to an inert gas was deposited in the temperature range from 200 to 300 0 C with a peak at 250 0 C (speciesA). This species is neither in a form combined with other fission products nor in elemental form. It is possibly a chemical combination with uranium. It reacts with oxygen, yielding species B characterized by its deposition at a temperature close to room temperature. The activation energy of this oxidation reaction was determined to be 6.0 +-0.5 Kcal/mol. Comparing the deposition-profile with those obtained with carrier-free I 2 and HI indicated that species B was I 2 . As for the formation of organic iodides accompanying the release in an inert gas, it was concluded that these were produced in radical reactions. Thus, in a presence of oxygen, organic iodides were formed in competition with the reactions of organic radicals with oxygen. (author)

Macroalgae-Derived Ingredients for Cosmetic Industry—An Update

Directory of Open Access Journals (Sweden)

Filipa B. Pimentel

2017-12-01

Full Text Available Aging is a natural and progressive declining physiological process that is influenced by multifactorial aspects and affects individuals’ health in very different ways. The skin is one of the major organs in which aging is more evident, as it progressively loses some of its natural functions. With the new societal paradigms regarding youth and beauty have emerged new concerns about appearance, encouraging millions of consumers to use cosmetic/personal care products as part of their daily routine. Hence, cosmetics have become a global and highly competitive market in a constant state of evolution. This industry is highly committed to finding natural sources of functional/bioactive-rich compounds, preferably from sustainable and cheap raw materials, to deliver innovative products and solutions that meet consumers’ expectations. Macroalgae are an excellent example of a natural resource that can fit these requirements. The incorporation of macroalgae-derived ingredients in cosmetics has been growing, as more and more scientific evidence reports their skin health-promoting effects. This review provides an overview on the possible applications of macroalgae as active ingredients for the cosmetic field, highlighting the main compounds responsible for their bioactivity on skin.

UNVEILING THE NATURE OF THE UNIDENTIFIED GAMMA-RAY SOURCES. V. ANALYSIS OF THE RADIO CANDIDATES WITH THE KERNEL DENSITY ESTIMATION

International Nuclear Information System (INIS)

Massaro, F.; Funk, S.; D'Abrusco, R.; Paggi, A.; Smith, Howard A.; Masetti, N.; Giroletti, M.; Tosti, G.

2013-01-01

Nearly one-third of the γ-ray sources detected by Fermi are still unidentified, despite significant recent progress in this area. However, all of the γ-ray extragalactic sources associated in the second Fermi-LAT catalog have a radio counterpart. Motivated by this observational evidence, we investigate all the radio sources of the major radio surveys that lie within the positional uncertainty region of the unidentified γ-ray sources (UGSs) at a 95% level of confidence. First, we search for their infrared counterparts in the all-sky survey performed by the Wide-field Infrared Survey Explorer (WISE) and then we analyze their IR colors in comparison with those of the known γ-ray blazars. We propose a new approach, on the basis of a two-dimensional kernel density estimation technique in the single [3.4] – [4.6] – [12] μm WISE color-color plot, replacing the constraint imposed in our previous investigations on the detection at 22 μm of each potential IR counterpart of the UGSs with associated radio emission. The main goal of this analysis is to find distant γ-ray blazar candidates that, being too faint at 22 μm, are not detected by WISE and thus are not selected by our purely IR-based methods. We find 55 UGSs that likely correspond to radio sources with blazar-like IR signatures. An additional 11 UGSs that have blazar-like IR colors have been found within the sample of sources found with deep recent Australia Telescope Compact Array observations

Literacy: An Essential Ingredient in the Recipe for Growth

Science.gov (United States)

Murray, Scott

2005-01-01

The ingredients that underpin economic growth are well-known and generally accepted; population growth, physical capital, financial capital and human capital all play a part in creating long term differences in the wealth of nations. There remains, however, considerable debate about the ideal recipe for economic growth. Recently, Statistics Canada…

Effect of ''outer'' sources and dissipative processes on abundance of inert gases in atmospheres of the Earth group planets

International Nuclear Information System (INIS)

Pavlov, A.K.

1981-01-01

The problem of abundance of inert gases in atmospheres of the Earth group planets is discussed. It is shown that introduction of He, Ne and 36 Ar into the Mars and Mercury atmospheres with interplanetary dust and from other external sources require the presence of special mechanisms of losses for these gases. For the Mars atmosphere dissipation on atmosphere interaction with solar wind during the periods of anomalously low temperatures is a probable mechanisms of Ne and 36 Ar losses. For the Mercury thermal dissipation for He and polar wind for other inert gases are possible. For all the planets of the Earth group dissipation on interaction with solar wind and introduction with interplanetary dust could play an important role at the early stages of evolution of planets [ru

ER stress stimulates production of the key antimicrobial peptide, cathelicidin, by forming a previously unidentified intracellular S1P signaling complex.

Science.gov (United States)

Park, Kyungho; Ikushiro, Hiroko; Seo, Ho Seong; Shin, Kyong-Oh; Kim, Young Il; Kim, Jong Youl; Lee, Yong-Moon; Yano, Takato; Holleran, Walter M; Elias, Peter; Uchida, Yoshikazu

2016-03-08

We recently identified a previously unidentified sphingosine-1-phosphate (S1P) signaling mechanism that stimulates production of a key innate immune element, cathelicidin antimicrobial peptide (CAMP), in mammalian cells exposed to external perturbations, such as UVB irradiation and other oxidative stressors that provoke subapoptotic levels of endoplasmic reticulum (ER) stress, independent of the well-known vitamin D receptor-dependent mechanism. ER stress increases cellular ceramide and one of its distal metabolites, S1P, which activates NF-κB followed by C/EBPα activation, leading to CAMP production, but in a S1P receptor-independent fashion. We now show that S1P activates NF-κB through formation of a previously unidentified signaling complex, consisting of S1P, TRAF2, and RIP1 that further associates with three stress-responsive proteins; i.e., heat shock proteins (GRP94 and HSP90α) and IRE1α. S1P specifically interacts with the N-terminal domain of heat shock proteins. Because this ER stress-initiated mechanism is operative in both epithelial cells and macrophages, it appears to be a universal, highly conserved response, broadly protective against diverse external perturbations that lead to increased ER stress. Finally, these studies further illuminate how ER stress and S1P orchestrate critical stress-specific signals that regulate production of one protective response by stimulating production of the key innate immune element, CAMP.

Chili Cookoff: Unique Ingredients Prove Successful in Ross Smith’s Big Pot of Chili | Poster

Science.gov (United States)

By Ashley DeVine, Staff Writer If the past is any indication, judges at the Protective Services Chili Cookoff give high marks for chili recipes containing unique or uncommon ingredients. Previous winning recipes have included ingredients such as black beans, pumpkin, pineapple, pork loin, and even bourbon. Judges at the 12th annual event, held Jan. 5, continued this tradition

Contact allergy to the 26 specific fragrance ingredients to be declared on cosmetic products in accordance with the EU cosmetics directive

DEFF Research Database (Denmark)

Heisterberg, Maria V; Menné, Torkil; Johansen, Jeanne D

2011-01-01

Background. Fragrance ingredients are a frequent cause of allergic contact dermatitis. The EU Cosmetics Directive states that 26 specific fragrance ingredients, known to cause allergic contact dermatitis, must be declared on the ingredient lists of cosmetic products. Objectives. To investigate...

Quality assurance of chemical ingredient classification for the National Drug File - Reference Terminology.

Science.gov (United States)

Zheng, Ling; Yumak, Hasan; Chen, Ling; Ochs, Christopher; Geller, James; Kapusnik-Uner, Joan; Perl, Yehoshua

2017-09-01

The National Drug File - Reference Terminology (NDF-RT) is a large and complex drug terminology consisting of several classification hierarchies on top of an extensive collection of drug concepts. These hierarchies provide important information about clinical drugs, e.g., their chemical ingredients, mechanisms of action, dosage form and physiological effects. Within NDF-RT such information is represented using tens of thousands of roles connecting drugs to classifications. In previous studies, we have introduced various kinds of Abstraction Networks to summarize the content and structure of terminologies in order to facilitate their visual comprehension, and support quality assurance of terminologies. However, these previous kinds of Abstraction Networks are not appropriate for summarizing the NDF-RT classification hierarchies, due to its unique structure. In this paper, we present the novel Ingredient Abstraction Network (IAbN) to summarize, visualize and support the audit of NDF-RT's Chemical Ingredients hierarchy and its associated drugs. A common theme in our quality assurance framework is to use characterizations of sets of concepts, revealed by the Abstraction Network structure, to capture concepts, the modeling of which is more complex than for other concepts. For the IAbN, we characterize drug ingredient concepts as more complex if they belong to IAbN groups with multiple parent groups. We show that such concepts have a statistically significantly higher rate of errors than a control sample and identify two especially common patterns of errors. Copyright © 2017 Elsevier Inc. All rights reserved.

40 CFR 180.950 - Tolerance exemptions for minimal risk active and inert ingredients.

Science.gov (United States)

2010-07-01

...) Both the raw and processed forms of peanuts, tree nuts, milk, soybeans, eggs, fish, crustacea, and... is an animal feed composed of dried animal fat and protein that has been sterilized. Other than meat.... The term commonly consumed food commodities shall only apply to food commodities (whether a raw...

Dynamics of soluble and inert pollutant concentrations in linear and deterministic systems with time varying parameters

International Nuclear Information System (INIS)

Meltzer, M.

1977-04-01

The tracer theory in steady and non-steady systems is presented. The unsteady system was applied in the study of the concentration dynamics of the National Water Carrier in Israel. A method that uses Bromine 82 for the investigation of the transfer time distribution and of the dynamics of inert matter concentration in the system is desribed. (B.G.)

Fungal treated lignocellulosic biomass as ruminant feed ingredient: A review

NARCIS (Netherlands)

Kuijk, van S.J.A.; Sonnenberg, A.S.M.; Baars, J.J.P.; Hendriks, W.H.; Cone, J.W.

2015-01-01

In ruminant nutrition, there is an increasing interest for ingredients that do not compete with human nutrition. Ruminants are specialists in digesting carbohydrates in plant cell walls; therefore lignocellulosic biomass has potential in ruminant nutrition. The presence of lignin in biomass,

Bioconversion of rice straw as animal feed ingredient through solid state fermentation

International Nuclear Information System (INIS)

Mohamad Hanif Mohamad Jamil; Sepiah Muid

1998-01-01

Work was conducted to establish procedures and techniques to utilise microorganisms, particularly basidiomycetes, for solid fermentation of rice by-products. The purpose of the study was to determine the potential of biologically processed rice by-products as ingredients of feed formula for selected livestock. Fungal organisms Auriculariapolytrichia, Lentimus connatus, L. edodes, Pleurotus cystidiosus, P. florida, P. sajor-caju and Volvariella volvacea respectively were inoculated on sterilised rice straw and the mycelium produced were cultured for periods of 3-4 weeks by which time the straw was fully enmeshed with mycelia. Proximate analysis of the finished products gave increases of 93-172 % crude protein and reduction of 31-54 % crude fibre on comparison with untreated rice straw. Amino acid analysis showed general increases for solid fermented rice straw (SFRS) which were comparatively close to amino acid values of conventional feed ingredients such as wheat, corn, sorghum and barley. Solid fermented rice straw was also tested as an ingredient in the formulation of rations for broiler chickens. Feeding trials on poultry indicated a maximum substitution of 50% maize with SFRS in feed rations was possible to attain acceptable growth of chickens to an average live final weight of 1.8 - 2.0 kg. per chicken at age 7 weeks. From studies undertaken, it was observed that the cellulolytic straw could be developed as a potential feed material for livestock through solid fermentation with microorganisms. From the research results, the use of solid fermented rice straw as an alternative ingredient in animal feeds may be one way in reducing reliance on feed imports and at the same time controlling environmental pollution. (Author)

21 CFR 352.20 - Permitted combinations of active ingredients.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Permitted combinations of active ingredients. 352.20 Section 352.20 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... effective date was stayed until further notice. For the convenience of the user, the text is set forth as...

21 CFR 344.12 - Ear drying aid active ingredient.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Ear drying aid active ingredient. 344.12 Section 344.12 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... alcohol 95 percent in an anhydrous glycerin 5 percent base. [65 FR 48905, Aug. 10, 2000] ...

Safety aspects of the production of foods and food ingredients from insects.

Science.gov (United States)

Schlüter, Oliver; Rumpold, Birgit; Holzhauser, Thomas; Roth, Angelika; Vogel, Rudi F; Quasigroch, Walter; Vogel, Stephanie; Heinz, Volker; Jäger, Henry; Bandick, Nils; Kulling, Sabine; Knorr, Dietrich; Steinberg, Pablo; Engel, Karl-Heinz

2017-06-01

At present, insects are rarely used by the European food industry, but they are a subject of growing interest as an alternative source of raw materials. The risks associated with the use of insects in the production of foods and food ingredients have not been sufficiently investigated. There is a lack of scientifically based knowledge of insect processing to ensure food safety, especially when these processes are carried out on an industrial scale. This review focuses on the safety aspects that need to be considered regarding the fractionation of insects for the production of foods and food ingredients. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

49 CFR 173.56 - New explosives-definition and procedures for classification and approval.

Science.gov (United States)

2010-10-01

... agency the ranges of composition of ingredients and compounds, showing the intended manufacturing... was produced to an explosives testing range if— (1) It is not a primary (a 1.1A initiating) explosive...) Ammunition with inert projectile or blank ammunition; and (4) Ammunition not exceeding 50 caliber for rifle...

21 CFR 579.40 - Ionizing radiation for the treatment of poultry feed and poultry feed ingredients.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Ionizing radiation for the treatment of poultry feed and poultry feed ingredients. 579.40 Section 579.40 Food and Drugs FOOD AND DRUG ADMINISTRATION... § 579.40 Ionizing radiation for the treatment of poultry feed and poultry feed ingredients. Ionizing...

Dark Matter candidate in Inert Doublet Model with additional local gauge symmetry U (1)

International Nuclear Information System (INIS)

Gaitán, R.; De Oca, J.H. Montes; Garcés, E. A.; Cabral-Rosetti, L. G.

2016-01-01

We consider the Inert Doublet Model (IDM) with an additional local gauge symmetry U (1) and a complex singlet scalar to break the symmetry U (1). The continuous symmetry U (1) is introduced to control the CP-conserving interaction instead of some discrete symmetries as usually. We present the mass spectrum for neutral scalar and gauge bosons and the values of the charges under U (1) for which the model could have a candidate to dark matter. (paper)

Inhibition of Listeria monocytogenes by propionic acid-based ingredients in cured deli-style Turkey.

Science.gov (United States)

Glass, Kathleen A; McDonnell, Lindsey M; Von Tayson, Roxanne; Wanless, Brandon; Badvela, Mani

2013-12-01

Listeria monocytogenes growth can be controlled on ready-to-eat meats through the incorporation of antimicrobial ingredients into the formulation or by postlethality kill steps. However, alternate approaches are needed to provide options that reduce sodium content but maintain protection against pathogen growth in meats after slicing. The objective of this study was to determine the inhibition of L. monocytogenes by propionic acid-based ingredients in high-moisture, cured turkey stored at 4 or 7°C. Six formulations of sliced, cured (120 ppm of NaNO2 ), deli-style turkey were tested, including control without antimicrobials, 3.2% lactate-diacetate blend (LD), 0.4% of a liquid propionate-benzoate-containing ingredient, or 0.3, 0.4, and 0.5% of a liquid propionate-containing ingredient. Products were inoculated with 5 log CFU L. monocytogenes per 100-g package (3 log CFU/ml rinsate), vacuum-sealed, and stored at 4 or 7°C for up to 12 weeks; and populations were enumerated by plating on modified Oxford agar. As expected, the control without antimicrobials supported rapid growth, with >2 log average per ml rinsate increase within 4 weeks of storage at 4°C, whereas growth was observed at 6 weeks for the LD treatment. For both replicate trials, all treatments that contained liquid propionate or propionate-benzoate limited L. monocytogenes growth to an increase of 1-log increase) was observed in individual samples for all propionate-containing treatments at weeks 10, 11, and 12. As expected, L. monocytogenes grew more rapidly when products were stored at 7°C, but trends in relative inhibition were similar to those observed at 4°C. These results verify that propionate-based ingredients inhibit growth of L. monocytogenes on sliced, high-moisture, cured turkey and can be considered as an alternative to reduce sodium-based salts while maintaining food safety.

Positive lists of cosmetic ingredients: Analytical methodology for regulatory and safety controls – A review

International Nuclear Information System (INIS)

Lores, Marta; Llompart, Maria; Alvarez-Rivera, Gerardo; Guerra, Eugenia; Vila, Marlene; Celeiro, Maria; Lamas, J. Pablo; Garcia-Jares, Carmen

2016-01-01

Cosmetic products placed on the market and their ingredients, must be safe under reasonable conditions of use, in accordance to the current legislation. Therefore, regulated and allowed chemical substances must meet the regulatory criteria to be used as ingredients in cosmetics and personal care products, and adequate analytical methodology is needed to evaluate the degree of compliance. This article reviews the most recent methods (2005–2015) used for the extraction and the analytical determination of the ingredients included in the positive lists of the European Regulation of Cosmetic Products (EC 1223/2009): comprising colorants, preservatives and UV filters. It summarizes the analytical properties of the most relevant analytical methods along with the possibilities of fulfilment of the current regulatory issues. The cosmetic legislation is frequently being updated; consequently, the analytical methodology must be constantly revised and improved to meet safety requirements. The article highlights the most important advances in analytical methodology for cosmetics control, both in relation to the sample pretreatment and extraction and the different instrumental approaches developed to solve this challenge. Cosmetics are complex samples, and most of them require a sample pretreatment before analysis. In the last times, the research conducted covering this aspect, tended to the use of green extraction and microextraction techniques. Analytical methods were generally based on liquid chromatography with UV detection, and gas and liquid chromatographic techniques hyphenated with single or tandem mass spectrometry; but some interesting proposals based on electrophoresis have also been reported, together with some electroanalytical approaches. Regarding the number of ingredients considered for analytical control, single analyte methods have been proposed, although the most useful ones in the real life cosmetic analysis are the multianalyte approaches. - Highlights: �

Positive lists of cosmetic ingredients: Analytical methodology for regulatory and safety controls – A review

Energy Technology Data Exchange (ETDEWEB)

Lores, Marta, E-mail: marta.lores@usc.es; Llompart, Maria; Alvarez-Rivera, Gerardo; Guerra, Eugenia; Vila, Marlene; Celeiro, Maria; Lamas, J. Pablo; Garcia-Jares, Carmen

2016-04-07

Cosmetic products placed on the market and their ingredients, must be safe under reasonable conditions of use, in accordance to the current legislation. Therefore, regulated and allowed chemical substances must meet the regulatory criteria to be used as ingredients in cosmetics and personal care products, and adequate analytical methodology is needed to evaluate the degree of compliance. This article reviews the most recent methods (2005–2015) used for the extraction and the analytical determination of the ingredients included in the positive lists of the European Regulation of Cosmetic Products (EC 1223/2009): comprising colorants, preservatives and UV filters. It summarizes the analytical properties of the most relevant analytical methods along with the possibilities of fulfilment of the current regulatory issues. The cosmetic legislation is frequently being updated; consequently, the analytical methodology must be constantly revised and improved to meet safety requirements. The article highlights the most important advances in analytical methodology for cosmetics control, both in relation to the sample pretreatment and extraction and the different instrumental approaches developed to solve this challenge. Cosmetics are complex samples, and most of them require a sample pretreatment before analysis. In the last times, the research conducted covering this aspect, tended to the use of green extraction and microextraction techniques. Analytical methods were generally based on liquid chromatography with UV detection, and gas and liquid chromatographic techniques hyphenated with single or tandem mass spectrometry; but some interesting proposals based on electrophoresis have also been reported, together with some electroanalytical approaches. Regarding the number of ingredients considered for analytical control, single analyte methods have been proposed, although the most useful ones in the real life cosmetic analysis are the multianalyte approaches. - Highlights: �

Development of Semiliquid Ingredients from Grape Skins and Their Potential Impact on the Reducing Capacity of Model Functional Foods

Directory of Open Access Journals (Sweden)

Milan Stojanovic

2018-01-01

Full Text Available Grape skins (GS, which can be considered as reusable coproducts of winemaking, were processed to develop semiliquid ingredients for functional foods, as an alternative to powdered GS, which needs high energy input for drying. Processing of semiliquid GS ingredients included blanching, dilution to obtain dispersions with 2% or 10% of dry solids, milling, homogenization, and pasteurization. The individual phenolic contents and in vitro ferric ion reducing capacity (FRAP of semiliquid GS ingredients were compared with those of air-dried and freeze-dried GS. With respect to freeze-dried GS, the recovery of FRAP values was ~75% for both air-dried GS and 2% GS dispersion and 59% for 10% GS dispersion. The average particle size diameters of solids in semiliquid GS ingredients were similar to those observed in commercial apple skin products. Possible applications of GS semiliquid ingredients to increase the reducing capacity of food 10 times include formulation into beverages and ice-type desserts and use in bakery products.

Acrylamide content distribution and possible alternative ingredients for snack foods.

Science.gov (United States)

Cheng, Wei Chih; Sun, De Chao; Chou, Shin Shou; Yeh, An I

2012-12-01

Acrylamide (AA) contents in 294 snack foods including cereal-based, root- and tuber-based, and seafood-based foods, nuts, dried beans, and dried fruits purchased in Taiwan were determined by gas chromatography-mass spectrometry in this study. The highest levels of average AA content were found in root- and tuber-based snack foods (435 μg/kg), followed by cereal-based snack foods (299 μg/kg). Rice flour-based, seafood-based, and dried fruit snack foods had the lowest average AA content (snack foods in Taiwan. The results could provide important data regarding intake information from the snack foods. In addition, the results showed a great diversity of AA content in snack foods prepared from different ingredients. Rice- and seafood-based products had much lower AA than those made from other ingredients. This information could constitute a good reference for consumers to select products for healthy snacking.

Screening of repeated dose toxicity data present in SCC(NF)P/SCCS safety evaluations of cosmetic ingredients.

Science.gov (United States)

Vinken, Mathieu; Pauwels, Marleen; Ates, Gamze; Vivier, Manon; Vanhaecke, Tamara; Rogiers, Vera

2012-03-01

Alternative methods, replacing animal testing, are urgently needed in view of the European regulatory changes in the field of cosmetic products and their ingredients. In this context, a joint research initiative called SEURAT was recently raised by the European Commission and COLIPA, representing the European cosmetics industry, with the overall goal of developing an animal-free repeated dose toxicity testing strategy for human safety assessment purposes. Although cosmetic ingredients are usually harmless for the consumer, one of the initial tasks of this research consortium included the identification of organs that could potentially be affected by cosmetic ingredients upon systemic exposure. The strategy that was followed hereof is described in the present paper and relies on the systematic evaluation, by using a self-generated electronic databank, of published reports issued by the scientific committee of DG SANCO responsible for the safety of cosmetic ingredients. By screening of the repeated dose toxicity studies present in these reports, it was found that the liver is potentially the most frequently targeted organ by cosmetic ingredients when orally administered to experimental animals, followed by the kidney and the spleen. Combined listing of altered morphological, histopathological, and biochemical parameters subsequently indicated the possible occurrence of hepatotoxicity, including steatosis and cholestasis, triggered by a limited number of cosmetic compounds. These findings are not only of relevance for the in vitro modeling efforts and choice of compounds to be tested in the SEURAT project cluster, but also demonstrate the importance of using previously generated toxicological data through an electronic databank for addressing specific questions regarding the safety evaluation of cosmetic ingredients.

21 CFR 333.320 - Permitted combinations of active ingredients.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Permitted combinations of active ingredients. 333.320 Section 333.320 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... Note: At 75 FR 9776, Mar. 4, 2010, § 333.320 was revised, effective Mar. 4, 2011. For the convenience...

Plant Cell Cultures as Source of Cosmetic Active Ingredients

Directory of Open Access Journals (Sweden)

Ani Barbulova

2014-04-01

Full Text Available The last decades witnessed a great demand of natural remedies. As a result, medicinal plants have been increasingly cultivated on a commercial scale, but the yield, the productive quality and the safety have not always been satisfactory. Plant cell cultures provide useful alternatives for the production of active ingredients for biomedical and cosmetic uses, since they represent standardized, contaminant-free and biosustainable systems, which allow the production of desired compounds on an industrial scale. Moreover, thanks to their totipotency, plant cells grown as liquid suspension cultures can be used as “biofactories” for the production of commercially interesting secondary metabolites, which are in many cases synthesized in low amounts in plant tissues and differentially distributed in the plant organs, such as roots, leaves, flowers or fruits. Although it is very widespread in the pharmaceutical industry, plant cell culture technology is not yet very common in the cosmetic field. The aim of the present review is to focus on the successful research accomplishments in the development of plant cell cultures for the production of active ingredients for cosmetic applications.

EU legislations affecting safety data availability of cosmetic ingredients.

Science.gov (United States)

Pauwels, Marleen; Rogiers, Vera

2007-12-01

With the introduction of the 6th and 7th Amendments (OJ L151, 32-37, 23 June 1993; OJ L066, 26-35, 11 March 2003) to the Cosmetic Products Directive (OJ L262, 169-200, 27 September 1976), imposing a testing and marketing ban on cosmetic products tested on animals, the retrieval of toxicological data on individual ingredients became of greater need. Since the majority of cosmetic ingredients are used for many other purposes than their cosmetic function, they fall under the scope of more than one EU Directive. An overview is given of EU legislation that could potentially affect the availability and interpretation of cosmetic safety data. It will become clear that, although cosmetics are regulated by a specific so-called "vertical" legislation, "horizontal" influences from other products' legislations play a role since they determine the type and amount of data that theoretically could be found on the specific substances they regulate. This knowledge is necessary while performing extended searches in databases and becomes indispensable when initiating negotiations with manufacturers or suppliers for obtaining the safety data required.

Concept study of a novel energy harvesting-enabled tuned mass-damper-inerter (EH-TMDI) device for vibration control of harmonically-excited structures

International Nuclear Information System (INIS)

Salvi, Jonathan; Giaralis, Agathoklis

2016-01-01

A novel dynamic vibration absorber (DVA) configuration is introduced for simultaneous vibration suppression and energy harvesting from oscillations typically exhibited by large-scale low-frequency engineering structures and structural components. The proposed configuration, termed energy harvesting-enabled tuned mass-damper-inerter (EH-TMDI) comprises a mass grounded via an in-series electromagnetic motor (energy harvester)-inerter layout, and attached to the primary structure through linear spring and damper in parallel connection. The governing equations of motion are derived and solved in the frequency domain, for the case of harmonically-excited primary structures, here modelled as damped single-degree- of-freedom (SDOF) systems. Comprehensive parametric analyses proved that by varying the mass amplification property of the grounded inerter, and by adjusting the stiffness and the damping coefficients using simple optimum tuning formulae, enhanced vibration suppression (in terms of primary structure peak displacement) and energy harvesting (in terms of relative velocity at the terminals of the energy harvester) may be achieved concurrently and at nearresonance frequencies, for a fixed attached mass. Hence, the proposed EH-TMDI allows for relaxing the trade-off between vibration control and energy harvesting purposes, and renders a dual-objective optimisation a practically-feasible, reliable task. (paper)

Scope of claim coverage in patents of fufang Chinese herbal drugs: Substitution of ingredients

Directory of Open Access Journals (Sweden)

Tian Jiaher

2011-08-01

Full Text Available Abstract Herbal ingredients in a Chinese fufang prescription are often replaced by one or several other herbal combinations. As there have been very few Chinese herbal patent infringement cases, it is still unclear how the Doctrine of Equivalents should be applied to determine the scope of 'equivalents' in Chinese fufang prescriptions. Case law principles from cases in other technical areas such as chemical patents and biological drug patents can be borrowed to ascertain a precise scope of a fufang patent. This article summarizes and discusses several chemical and biopharmaceutical patent cases. In cases where a certain herbal ingredient is substituted by another herb or a combination of herbs, accused infringers are likely to relate herbal drug patents to chemical drug patents with strict interpretation whereas patent owners may take advantage of the liberal application of Doctrine of Equivalence in biopharmaceutical patents by analogizing the complex nature of herbal drugs with biological drugs. Therefore, consideration should be given to the purpose of an ingredient in a patent, the qualities when combined with the other ingredients and the intended function. The scope of equivalents also depends on the stage of the prior art. Moreover, it is desirable to disclose any potential substitutes when drafting the application. Claims should be drafted in such a way that all foreseeable modifications are encompassed for the protection of the patent owner's intellectual property.

Nano-microdelivery systems for oromucosal delivery of an active ingredient

DEFF Research Database (Denmark)

2014-01-01

A composition for oromucosal delivery of at least one active ingredient, more particularly a lipid nano-microdelivery system comprising a nicotine component and/or a flavour component, wherein the nicotine component may be delivered to the oral cavity via absorption through the mucosal membranes...

[Important application of intestinal transporters and metabolism enzymes on gastrointestinal disposal of active ingredients of Chinese materia medica].

Science.gov (United States)

Bi, Xiaolin; Du, Qiu; Di, Liuqing

2010-02-01

Oral drug bioavailability depends on gastrointestinal absorption, intestinal transporters and metabolism enzymes are the important factors in drug gastrointestinal absorption and they can also be induced or inhibited by the active ingredients of Chinese materia medica. This article presents important application of intestinal transporters and metabolism enzymes on gastrointestinal disposal of the active ingredients of Chinese materia medica, and points out the importance of research on transport and metabolism of the active ingredients of Chinese materia medica in Chinese extract and Chinese medicinal formulae.

On the Origin of the 3.3 μ m Unidentified Infrared Emission Feature

Energy Technology Data Exchange (ETDEWEB)

Sadjadi, Seyedabdolreza; Zhang, Yong; Kwok, Sun, E-mail: sunkwok@hku.hk [Laboratory for Space Research, Faculty of Science, The University of Hong Kong, Pokfulam Road, Hong Kong (China)

2017-08-20

The 3.3 μ m unidentified infrared emission feature is commonly attributed to the C–H stretching band of aromatic molecules. Astronomical observations have shown that this feature is composed of two separate bands at 3.28 and 3.30 μ m, and the origin of these two bands is unclear. In this paper, we perform vibrational analyses based on quantum mechanical calculations of 153 organic molecules, including both pure aromatic molecules and molecules with mixed aromatic/olefinic/aliphatic hydridizations. We find that many of the C–H stretching vibrational modes in polycyclic aromatic hydrocarbon (PAH) molecules are coupled. Even considering the uncoupled modes only, the correlation between the band intensity ratios and the structure of the PAH molecule is not observed, and the 3.28 and 3.30 μ m features cannot be directly interpreted in the PAH model. Based on these results, the possible aromatic, olefinic, and aliphatic origins of the 3.3 μ m feature are discussed. We suggest that the 3.28 μ m feature is assigned to aromatic C–H stretch whereas the 3.30 μ m feature is olefinic. From the ratio of these two features, the relative olefinic to aromatic content of the carrier can be determined.

21 CFR 310.548 - Drug products containing colloidal silver ingredients or silver salts offered over-the-counter...

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Drug products containing colloidal silver... Drug products containing colloidal silver ingredients or silver salts offered over-the-counter (OTC) for the treatment and/or prevention of disease. (a) Colloidal silver ingredients and silver salts have...

Standardized Ileal Amino Acid Digestibility of Commonly Used Feed Ingredients in Growing Broilers

Directory of Open Access Journals (Sweden)

Zafar Ullah

2016-09-01

Full Text Available This experiment was conducted to determine standardized ileal amino acid digestibility (SIAAD of commonly used feed ingredients in poultry diets in Pakistan. These feed ingredients included corn, rice broken (RB, rice polishings (RP, wheat bran (WB, sunflower meal (SFM, cottonseed meal (CSM, guar meal (GM, soybean meal (SBM from India and Argentine and fish meal (FM. The SIAAD of each ingredient was determined in triplicate using 21-days-old broilers. Day-old male broiler chicks (Hubbard× Hubbard were reared on corn-SBM based diet from 1 to 13 days and thereafter birds were fed experimental diets from day 14 to 21. Each diet was fed to 36 birds kept in six replicate cages, each cage had six birds. In cereals, the SIAAD of corn’s amino acid (AA (90.1% was similar (p>0.05 to RB (89.0%. Isoleucine (97.8% and lysine (96.9% were highly digestible AA in corn and RB, respectively. Among cereal-by products, WB’s SIAAD (76.9% was same (p>0.05 as RP (71.9%. Arginine from WB (82.5% and RP (83.2% was highly digestible. However, threonine in WB (72.7% and leucine in RP (69.6% were the lowest digestible AAs. In plant protein meals, AAs from Argentine-SBM (85.1% and Indian-SBM (83.4% had higher (p0.05. The SBM from plant protein meals had higher (p<0.05 SIAAD than other studied feed ingredients. However, the GM had the lowest (p<0.05 SIAAD among protein meals.

Beyond "Inert" Ideas to Teaching General Chemistry from Rich Contexts: Visualizing the Chemistry of Climate Change (VC3)

Science.gov (United States)

Mahaffy, Peter G.; Holme, Thomas A.; Martin-Visscher, Leah; Martin, Brian E.; Versprille, Ashley; Kirchhoff, Mary; McKenzie, Lallie; Town, Marcy

2017-01-01

As one approach to moving beyond transmitting "inert" ideas to chemistry students, we use the term "teaching from rich contexts" to describe implementations of case studies or context-based learning based on systems thinking that provide deep and rich opportunities for learning crosscutting concepts through contexts. This…

Development of a Consumer Product Ingredient Database for ...

Science.gov (United States)

Consumer products are a primary source of chemical exposures, yet little structured information is available on the chemical ingredients of these products and the concentrations at which ingredients are present. To address this data gap, we created a database of chemicals in consumer products using product Material Safety Data Sheets (MSDSs) publicly provided by a large retailer. The resulting database represents 1797 unique chemicals mapped to 8921 consumer products and a hierarchy of 353 consumer product “use categories” within a total of 15 top-level categories. We examine the utility of this database and discuss ways in which it will support (i) exposure screening and prioritization, (ii) generic or framework formulations for several indoor/consumer product exposure modeling initiatives, (iii) candidate chemical selection for monitoring near field exposure from proximal sources, and (iv) as activity tracers or ubiquitous exposure sources using “chemical space” map analyses. Chemicals present at high concentrations and across multiple consumer products and use categories that hold high exposure potential are identified. Our database is publicly available to serve regulators, retailers, manufacturers, and the public for predictive screening of chemicals in new and existing consumer products on the basis of exposure and risk. The National Exposure Research Laboratory’s (NERL’s) Human Exposure and Atmospheric Sciences Division (HEASD) conducts resear

Database search for safety information on cosmetic ingredients.

Science.gov (United States)

Pauwels, Marleen; Rogiers, Vera

2007-12-01

Ethical considerations with respect to experimental animal use and regulatory testing are worldwide under heavy discussion and are, in certain cases, taken up in legislative measures. The most explicit example is the European cosmetic legislation, establishing a testing ban on finished cosmetic products since 11 September 2004 and enforcing that the safety of a cosmetic product is assessed by taking into consideration "the general toxicological profile of the ingredients, their chemical structure and their level of exposure" (OJ L151, 32-37, 23 June 1993; OJ L066, 26-35, 11 March 2003). Therefore the availability of referenced and reliable information on cosmetic ingredients becomes a dire necessity. Given the high-speed progress of the World Wide Web services and the concurrent drastic increase in free access to information, identification of relevant data sources and evaluation of the scientific value and quality of the retrieved data, are crucial. Based upon own practical experience, a survey is put together of freely and commercially available data sources with their individual description, field of application, benefits and drawbacks. It should be mentioned that the search strategies described are equally useful as a starting point for any quest for safety data on chemicals or chemical-related substances in general.

Novel botanical ingredients for beverages.

Science.gov (United States)

Gruenwald, Joerg

2009-01-01

Natural substances are generally preferred over chemical ones and are generally seen as healthy. The increasing demand for natural ingredients, improving health and appearance, is also attracting beverages as the fastest growing segment on the functional food market. Functional beverages are launched as fortified water, tea, diary or juices claiming overall nutrition, energy, anti-aging or relaxing effects. The substitution of so called superfruits, such as berries, grapes, or pomegranate delivers an effective range of beneficial compounds, including vitamins, fatty acids, minerals, and anti-oxidants. In this context, new exotic and African fruits could be useful sources in the near future. Teas and green botanicals, such as algae or aloe vera are also rich in effective bioactives and have been used traditionally. The botanical kingdom offers endless possibilities.

Neotropics and natural ingredients for pharmaceuticals: why isn't South American biodiversity on the crest of the wave?

Science.gov (United States)

Desmarchelier, Cristian

2010-06-01

Despite the advent of biotechnology and modern methods of combinatorial chemistry and rational drug design, nature still plays a surprisingly important role as a source of new pharmaceutical compounds. These are marketed either as herbal drugs or as single active ingredients. South American tropical ecosystems (or the Neotropics) encompass one-third of the botanical biodiversity of the planet. For centuries, indigenous peoples have been using plants for healing purposes, and scientists are making considerable efforts in order to validate these uses from a pharmacological/phytochemical point of view. However, and despite the unique plant diversity in the region, very few natural pharmaceutical ingredients from this part of the world have reached the markets in industrialized countries. The present review addresses the importance of single active ingredients and herbal drugs from South American flora as natural ingredients for pharmaceuticals; it highlights the most relevant cases in terms of species of interest; and discusses the key entry barriers for these products in industrialized countries. It explores the reasons why, in spite of the region's competitive advantages, South American biodiversity has been a poor source of natural ingredients for the pharmaceutical industry. (c) 2010 John Wiley & Sons, Ltd.

[Effects of ingredients from Chinese herbs with nature of cold or hot on expression of TRPV1 and TRPM8].

Science.gov (United States)

Sui, Feng; Yang, Na; Zhang, Changbin; Du, Xinliang; Li, Lanfang; Weng, Xiaogang; Guo, Shuying; Huo, Hairu; Jiang, Tingliang

2010-06-01

To study the effects of the ingredients from Chinese herbs with the nature of cold or hot on the expression of TRPV1 and TRPM8. The effects of ingredients from herbs on primary culture DRG neurons are observed in vitro. The expression quantity of gene is detected by the method of real time PCR. the 2 (-deltadeltaCT) method is applied to analyze the data. Ingredients from herbs with the nature of cold up-regulate the expression level of TRPV1 and down-regulate that of TRPM8, especially under the temperature condition of 39 degrees C; while ingredients from herbs with the nature of hot up-regulate the expression level of TRPM8 and down-regulated that of TRPV1, which is more significant under the temperature condition of 19 degrees C. The regulatory changes of TRPV1 and TRPM8 mRNA expression induced by the chemical ingredients might be related to the cold and hot natures of the herbs from which the ingredients are extracted. And this could be one of the therapeutic mechanisms for the treatment of Chinese herbal medicines to cold- and heat-related diseases.

Consumer needs and requirements for food and ingredient traceability information

NARCIS (Netherlands)

Rijswijk, van W.; Frewer, L.J.

2012-01-01

The introduction of improved food traceability systems has aimed to restore consumer confidence in food safety and quality, in part by being able to provide consumers with more information about the origins of foods and food ingredients. However, little is known about consumers’ opinions and beliefs

Structuring of expanded snacks based on patato ingredients : a review

NARCIS (Netherlands)

Sman, van der R.G.M.; Broeze, J.

2013-01-01

In this paper we review the current knowledge on the structuring via bubble expansion of starchy snacks, which are formulated on the basis of potato ingredients. These snacks are rarely discussed in scientific literature, but there are a scant number of patents dealing with various formulations and

Indigenous food ingredients for complementary food formulations to combat infant malnutrition in Benin: a review.

Science.gov (United States)

Chadare, Flora J; Madode, Yann E; Fanou-Fogny, Nadia; Kindossi, Janvier M; Ayosso, Juvencio Og; Honfo, S Hermann; Kayodé, Ap Polycarpe; Linnemann, Anita R; Hounhouigan, D Joseph

2018-01-01

This paper reviews indigenous Beninese food resources as potential ingredients for complementary infant foods with the aim to develop affordable formulations for low-income households in each agro-ecological zone of the country. Potential ingredients were selected on their documented nutritional value. The selected foods encompass 347 food resources, namely 297 plant products from home gardens or collected from natural vegetation and 50 animals, either domesticated or from the wild. The compiled data reveal that the distribution of the available food resources was unbalanced between agro-ecological zones. Only a few animal ingredients are obtainable in northern Benin. Most resources are seasonal, but their availability may be extended. A high variation was observed in energy and nutrient contents. Antinutritional factors were identified in some resources, but processing techniques were reported to reduce their presence in meals. In general, ingredients from local tree foods (Adansonia digitata, Parkia biglobosa) were adequate as sources of nutrients for complementary infant foods. Based on this review, local foods for the development of complementary food formulas for Beninese infants and children may be selected for each agro-ecological zone. The approach used is exemplary for other sub-Saharan African countries in need of complementary infant foods. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Control of degradation of spent LWR [light-water reactor] fuel during dry storage in an inert atmosphere

International Nuclear Information System (INIS)

Cunningham, M.E.; Simonen, E.P.; Allemann, R.T.; Levy, I.S.; Hazelton, R.F.

1987-10-01

Dry storage of Zircaloy-clad spent fuel in inert gas (referred to as inerted dry storage or IDS) is being developed as an alternative to water pool storage of spent fuel. The objectives of the activities described in this report are to identify potential Zircaloy degradation mechanisms and evaluate their applicability to cladding breach during IDS, develop models of the dominant Zircaloy degradation mechanisms, and recommend cladding temperature limits during IDS to control Zircaloy degradation. The principal potential Zircaloy cladding breach mechanisms during IDS have been identified as creep rupture, stress corrosion cracking (SCC), and delayed hydride cracking (DHC). Creep rupture is concluded to be the primary cladding breach mechanism during IDS. Deformation and fracture maps based on creep rupture were developed for Zircaloy. These maps were then used as the basis for developing spent fuel cladding temperature limits that would prevent cladding breach during a 40-year IDS period. The probability of cladding breach for spent fuel stored at the temperature limit is less than 0.5% per spent fuel rod. 52 refs., 7 figs., 1 tab

SEED AND POLLEN TTRANSMISSION OF A NEW UNIDENTIFIED MOTTLE DISORDER OF MAIZE IN INDONESIA

Directory of Open Access Journals (Sweden)

W. Wakman

2018-01-01

Full Text Available A new unidentified mottle disorder of maize Indonesia was found at the Research Institute for Maize and Other Cereals (RIMOC, Maros, South Sulawesi in 1995. Attempts to identify the disorder were made by mechanical inoculation, insect vector (Rhopalosiphum maidis and Peregrinus maidis transmission, seed and pollen transmission, electron microscopy, and serological test. Fifty seeds from each of 22 ears of Arjuna maize plants showing the disorder were planted and symptoms on the seedlings were recorder at 1, 2, and 3 weeks after planting. The percentage of seedlings showing the disorder ranged from 40 to 100. Pollen of affected Arjuna was then used to pollinate four sweet corn female flowers. Hybrid seeds (50 per ear of the crosses were planted and symptoms were recorded at 1, 2, and 3 weeks after planting. The results showed that percentage of seedlings showing the disorder ranged from 22 to 84. Electron microscopy and ELISA tests on 15 viruses and one phytospiroplasma antiserum however, gave negative results. Therefore, maize disorder at Maros was not identical to any known viral disease of maize. It could be a genetical disorder and has been given the name maize mottle.

Role of inert gases in first wall phenomena in fusion devices

International Nuclear Information System (INIS)

Das, S.K.

1979-01-01

The first wall surfaces of fusion devices will be exposed to bombardment by inert gaseous projectiles such as helium. The flux, energy and angular distribution of the helium radiation will depend not only on the type of device but also on its design parameters. For near term tokamak devices, the first wall surface phenomena caused by helium bombardment that appear to be quite important are physical sputtering and radiation blistering. Examples of these processes for a number of first wall candidate materials are discussed. While the physical sputtering phenomen is well understood, the mechanism of blister formation is still not fully understood. The various models proposed for radiation blistering of metal during helium bombardment is critically reviewed in the light of most recent experimental results

Production of inert scalars at the high energy e+e− colliders

International Nuclear Information System (INIS)

Hashemi, Majid; Krawczyk, Maria; Najjari, Saereh; Żarnecki, Aleksander Filip

2016-01-01

We investigate the phenomenology of the light charged and neutral scalars in Inert Doublet Model at future e + e − colliders with center of mass energies of 0.5 and 1 TeV, and integrated luminosity of 500 fb −1 . The analysis covers two production processes, e + e − →H + H − and e + e − →AH, and consists of signal selections, cross section determinations as well as dark matter mass measurements. Several benchmark points are studied with focus on H ± →W ± H and A→ZH decays. It is concluded that the signal will be well observable in different final states allowing for mass determination of all new scalars with statistical precision of the order of few hundred MeV.

Methods of obtaining an inert atmosphere for plutonium metal treatment installations; Modes d'obtention d'une atmosphere inerte dans les installations d'elaboration du plutonium metallique

Energy Technology Data Exchange (ETDEWEB)

Riolfo, R; Barbier, M

1962-07-01

Plutonium is a very pyrophoric metal (heat of combustion: 253 kCal/mole). The operations and manipulations involved in its treatment have thus to be carried out in an inert atmosphere. Several methods designed to eliminate the oxygen from the manipulation chamber have been tried: absorption by titanium - zirconium or copper turnings, or bubbling through potassium pyrogallate. They are not satisfactory. The reaction C + O{sub 2} -> CO{sub 2} has been chosen. Graphite is used. By this method, which is flexible and which has a negligible cost price, it is possible to absorb O{sub 2} within a wide range of concentrations (from 0.1 to 20 per cent) at a temperature 600 - 800 deg C compatible with the use of a conventional material. This report describes the trials carried out, the method selected and experimented, with the experimental details, the results obtained, and the extension of the method for a slightly different use. (authors) [French] Le plutonium est un metal tres pyrophorique (chaleur de combustion 253 kCal/mole). Les operations et manipulations qui decoulent de son elaboration doivent donc s'effectuer sous atmosphere inerte. Plusieurs methodes, dont le but etait d'eliminer l'oxygene de l'enceinte d'elaboration ont ete essayees: absorption par des copeaux de titane-zirconium, de cuivre, ou barbotage sur le pyrogallate de potasse. Elles n'ont pas donne satisfaction. La reaction C + O{sub 2} {yields} CO{sub 2} a ete retenue. On utilise le graphite. D'une tres grande souplesse d'utilisation, d'un prix de revient nul, il permet d'absorber l'oxygene dans une fourchette etendue de concentration (0,1 a 20 pour cent) a une temperature (600 a 800 degres C) compatible avec l'emploi d'un materiel classique. Cet expose decrit les essais effectues, la methode retenue et experimentee, le mode operatoire, les resultats obtenus, et l'extension de la methode a un probleme legerement different. (auteurs)

Construction of Models for Nondestructive Prediction of Ingredient Contents in Blueberries by Near-infrared Spectroscopy Based on HPLC Measurements.

Science.gov (United States)

Bai, Wenming; Yoshimura, Norio; Takayanagi, Masao; Che, Jingai; Horiuchi, Naomi; Ogiwara, Isao

2016-06-28

Nondestructive prediction of ingredient contents of farm products is useful to ship and sell the products with guaranteed qualities. Here, near-infrared spectroscopy is used to predict nondestructively total sugar, total organic acid, and total anthocyanin content in each blueberry. The technique is expected to enable the selection of only delicious blueberries from all harvested ones. The near-infrared absorption spectra of blueberries are measured with the diffuse reflectance mode at the positions not on the calyx. The ingredient contents of a blueberry determined by high-performance liquid chromatography are used to construct models to predict the ingredient contents from observed spectra. Partial least squares regression is used for the construction of the models. It is necessary to properly select the pretreatments for the observed spectra and the wavelength regions of the spectra used for analyses. Validations are necessary for the constructed models to confirm that the ingredient contents are predicted with practical accuracies. Here we present a protocol to construct and validate the models for nondestructive prediction of ingredient contents in blueberries by near-infrared spectroscopy.

76 FR 76890 - Nutrition Labeling of Single-Ingredient Products and Ground or Chopped Meat and Poultry Products...

Science.gov (United States)

2011-12-09

.... FSIS-2005-0018] Nutrition Labeling of Single-Ingredient Products and Ground or Chopped Meat and Poultry... major cuts of single-ingredient, raw meat and poultry products and ground or chopped meat and poultry... Ground or Chopped Meat and Poultry Products'' in the Federal Register (75 FR 82148) that, among other...

Assessment of aflatoxin B1 in livestock feed and feed ingredients by high-performance thin layer chromatography

Directory of Open Access Journals (Sweden)

Korrapati Kotinagu

2015-12-01

Full Text Available Aim: Detection of aflatoxin B1 in Livestock compound Feed and feed ingredients by high-performance thin layer chromatography (HPTLC. Materials and Methods: Chromatography was performed on HPTLC silica gel 60 F 254, aluminum sheets by CAMAG automatic TLC sampler 4, with mobile phase condition chloroform:acetone:water (28:4:0.06. Extraction of aflatoxin B1 from samples was done as per AOAC method and screening and quantification done by HPTLC Scanner 4 under wavelength 366 nm. Results: A total of 97 livestock feed (48 and feed ingredients (49 samples received from different livestock farms and farmers were analyzed for aflatoxin B1of which 29 samples were contaminated, constituting 30%. Out of 48 livestock compound feed samples, aflatoxin B1 could be detected in 16 samples representing 33%, whereas in livestock feed ingredients out of 49 samples, 13 found positive for aflatoxin B1 representing 24.5%. Conclusion: HPTLC assures good recovery, precision, and linearity in the quantitative determination of aflatoxin B1 extracted from Livestock compound feed and feed ingredients. As more number of feed and feed ingredients are contaminated with aflatoxin B1 which causes deleterious effects in both animal and human beings, so there is a need for identifying the source of contamination, executing control measures, enabling better risk assessment techniques, and providing economic benefits.

Introducing CSR - The Missing Ingredient in the Land Reform Recipe?

African Journals Online (AJOL)

This article identifies corporate social responsibility (CSR) as one of the missing ingredients in the recipe for a successful land reform programme. The article introduces CSR and discusses the business case for CSR; identifies its benefits; considers its possible limitations; and examines the major drivers behind the notion.

Consumer preferences for different combinations of carriers and functional ingredients

DEFF Research Database (Denmark)

Krutulyte, Rasa; Grunert, Klaus G.; Scholderer, Joachim

Kleef, van Trijp & Luning, 2005; Patch, Tapsell & Williams, 2005). With this in mind, the present study aimed at uncovering which functional ingredients consumers accept in selected food product categories such as yoghurt, muesli bars, fish balls, tuna salad, baby meals, rye bread and liver pâté...

Fibre content and physiochemical properties of various horse feed ingredients

DEFF Research Database (Denmark)

Brøkner, Christine; Knudsen, Knud Erik Bach; Tauson, Anne-Helene

2010-01-01

There is an increasing need for identifying energy dense feed ingredients based on fibre, as starch has been shown to cause health problems in sports horses (Kronfeld et al., 2005). This experiment aimed at evaluating feeds considered to be suitable for horses by use of an enzymatic-chemical diet...

Non-animal photosafety screening for complex cosmetic ingredients with photochemical and photobiochemical assessment tools.

Science.gov (United States)

Nishida, Hayato; Hirota, Morihiko; Seto, Yoshiki; Suzuki, Gen; Kato, Masashi; Kitagaki, Masato; Sugiyama, Mariko; Kouzuki, Hirokazu; Onoue, Satomi

2015-08-01

Previously, a non-animal screening approach was proposed for evaluating photosafety of cosmetic ingredients by means of in vitro photochemical and photobiochemical assays; however, complex cosmetic ingredients, such as plant extracts and polymers, could not be evaluated because their molecular weight is often poorly defined and so their molar concentration cannot be calculated. The aim of the present investigation was to establish a photosafety screen for complex cosmetic ingredients by using appropriately modified in vitro photosafety assays. Twenty plant extracts were selected as model materials on the basis of photosafety information, and their phototoxic potentials were assessed by means of ultraviolet (UV)/visible light (VIS) spectral analysis, reactive oxygen species (ROS)/micellar ROS (mROS) assays, and 3T3 neutral red uptake phototoxicity testing (3T3 NRU PT). The maximum UV/VIS absorption value was employed as a judgment factor for evaluating photoexcitability of samples, and the value of 1.0 was adopted as a tentative criterion for photosafety identification. The ROS/mROS assays were conducted at 50 μg/mL, and no false negative prediction was obtained. Furthermore, the ROS/mROS assays at 50 μg/mL had a similar predictive capacity to the ROS/mROS assays in the previous study. A systematic tiered approach for simple and rapid non-animal photosafety evaluation of complex cosmetic ingredients can be constructed using these modified in vitro photochemical assays. Copyright © 2015 Elsevier Inc. All rights reserved.

Bioactive and inert dental glass-ceramics.

Science.gov (United States)

Montazerian, Maziar; Zanotto, Edgar Dutra

2017-02-01

The global market for dental materials is predicted to exceed 10 billion dollars by 2020. The main drivers for this growth are easing the workflow of dentists and increasing the comfort of patients. Therefore, remarkable research projects have been conducted and are currently underway to develop improved or new dental materials with enhanced properties or that can be processed using advanced technologies, such as CAD/CAM or 3D printing. Among these materials, zirconia, glass or polymer-infiltrated ceramics, and glass-ceramics (GCs) are of great importance. Dental glass-ceramics are highly attractive because they are easy to process and have outstanding esthetics, translucency, low thermal conductivity, high strength, chemical durability, biocompatibility, wear resistance, and hardness similar to that of natural teeth, and, in certain cases, these materials are bioactive. In this review article, we divide dental GCs into the following two groups: restorative and bioactive. Most restorative dental glass-ceramics (RDGCs) are inert and biocompatible and are used in the restoration and reconstruction of teeth. Bioactive dental glass-ceramics (BDGCs) display bone-bonding ability and stimulate positive biological reactions at the material/tissue interface. BDGCs are suggested for dentin hypersensitivity treatment, implant coating, bone regeneration and periodontal therapy. Throughout this paper, we elaborate on the history, processing, properties and applications of RDGCs and BDGCs. We also report on selected papers that address promising types of dental glass-ceramics. Finally, we include trends and guidance on relevant open issues and research possibilities. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 105A: 619-639, 2017. © 2016 Wiley Periodicals, Inc.

Anti-bacteria Effect of Active Ingredients of Cacumen Platycladi on the Spoilage Bacteria of Sauced Pork Head Meat

Science.gov (United States)

Li, Xiao; Xu, Lingyi; Cui, Yuqian; Pang, Meixia; Wang, Fang; Qi, Jinghua

2017-12-01

Extraction and anti-bacteria effect of active ingredients of Cacumen Platycladi were studied in this paper. Extraction combined with ultrasonic was adopted. The optimum extraction condition was determined by single factor test; the anti-bacteria effect of active ingredients and minimum inhibitory concentration(MIC) were valued by Oxford-cup method. The results indicated that kaempferol was the active ingredients of Cacumen Platycladi whose optimum extraction condition for ethanol concentrations were sixty-five percent and twenty minutes with ultrasonic assisted extraction.; the active ingredients of Cacumen Platycladi had anti-bacteria effect on Staphylococcus, Proteus, Bacillus, Serratia and MIC was 0.5 g/mL,0.5 g/mL,0.0313 g/mL and 0.0625 g/mL. The active constituent of Cacumen Platycladi is kaempferol which has obvious anti-bacteria effect and can be used to prolong the shelf-life of Low-temperature meat products.

Added ingredients affect the microbiota and biochemical characteristics of durum wheat type-I sourdough.

Science.gov (United States)

Minervini, Fabio; Celano, Giuseppe; Lattanzi, Anna; De Angelis, Maria; Gobbetti, Marco

2016-12-01

This study aimed at understanding the effect of additional ingredients (baker's yeast, macerated pears, grape must, honey, or water from macerated pears) on the microbiota and biochemical characteristics of durum wheat-based sourdough. One dough prepared using only flour was used as the control (control-dough). Compared to the control-dough, doughs containing additional ingredients showed higher (P  0.7, P < 0.05) with several biochemical characteristics of the sourdoughs (e.g., free amino acids and their derivatives). Copyright © 2016 Elsevier Ltd. All rights reserved.

40 CFR 172.24 - State issuance of permits.

Science.gov (United States)

2010-07-01

... animals for testing purposes, or otherwise disposed of in a manner which will not endanger man or the... Cosmetic Act; and (ii) The proposed program would not reasonably be expected to result in residues of the..., Drug and Cosmetic Act; and (iii) All inert ingredients in the pesticide are exempted from the...

Effect of ingredient particle sizes and dietary viscosity on digestion and faecal waste of striped catfish (Pangasianodon hypophthalmus)

NARCIS (Netherlands)

Tran, Tu; Hien, T.T.T.; Bosma, R.H.; Heinsbroek, L.T.N.; Verreth, J.A.J.; Schrama, J.W.

2017-01-01

The ingredients' particle size and dietary viscosity may alter digestion, performance and faecal waste management of fish. This study aimed to assess the effect of grinding screen sizes of feed ingredients and dietary viscosity on digestibility, faecal waste and performance of striped catfish

Effect of ingredient particle sizes and dietary viscosity on digestion and faecal waste of striped catfish (Pangasianodon hypophthalmus)

NARCIS (Netherlands)

Tran, Tu; Hien, T.T.T.; Bosma, R.H.; Heinsbroek, L.T.N.; Verreth, J.A.J.; Schrama, J.W.

2018-01-01

The ingredients' particle size and dietary viscosity may alter digestion, performance and faecal waste management of fish. This study aimed to assess the effect of grinding screen sizes of feed ingredients and dietary viscosity on digestibility, faecal waste and performance of striped catfish

Comparison of amino acid digestibility of feed ingredients in broilers, laying hens and caecectomised roosters.

Science.gov (United States)

Adedokun, S A; Utterback, P; Parsons, C M; Adeola, O; Lilburn, M S; Applegate, T J

2009-05-01

1. This study determined the effect of bird type (broilers, laying hens, or caecectomised roosters) on amino acid digestibility of feedstuffs from 5 plant sources and one animal source. 2. The standardised amino acid digestibility (SAAD) were obtained by correcting apparent ileal amino acid digestibility (AIAAD) values for basal ileal endogenous amino acid (EAA) flow obtained by feeding a N-free diet (NFD) to broilers and laying hens or from fasted EAA flow from caecectomised roosters. 3. The apparent total amino acid (TAA) digestibilities did not differ between broilers and roosters for three of the 6 feed ingredients. 4. Broilers had higher apparent total amino acid (TAA) digestibility than laying hens and roosters when fed on the maize diet (canola meal, maize, and soybean meal). 5. The apparent TAA digestibilities were similar across bird types for the dark distillers' dried grain with solubles, but the apparent lysine digestibility was much lower in the caecectomised roosters (15%) than the broilers (49%) and laying hens (43%). 6. The standardised TAA digestibility values in roosters were higher than in broilers for three of the 6 feed ingredients (canola meal, soybean meal, or meat and bone meal). 7. There were no differences between broilers and roosters, however, in the standardised TAA digestibility values for maize, dark and light DDGS. 8. The standardised TAA digestibility values for laying hens were lower for maize, higher for meat and bone meal, but no different for the remaining ingredients when compared with broilers. 9. The results from this study showed that both the apparent and standardised amino acid digestibility values in caecectomised roosters, laying hens, and broilers ingredients are similar for some, but not all, feed ingredients. 10. Nutritionists should, therefore, be cautious about using digestibility coefficients obtained by different methodologies as values may differ.

Prebiotics as functional food ingredients preventing diet-related diseases.

Science.gov (United States)

Florowska, A; Krygier, K; Florowski, T; Dłużewska, E

2016-05-18

This paper reviews the potential of prebiotic-containing foods in the prevention or postponement of certain diet-related diseases, such as cardiovascular diseases with hypercholesterolemia, osteoporosis, diabetes, gastrointestinal infections and gut inflammation. Also the data on prebiotics as food ingredients and their impact on food product quality are presented. Prebiotics are short chain carbohydrates that are resistant to the digestion process in the upper part of the digestive system, are not absorbed in any segment of the gastrointestinal system, and finally are selectively fermented by specific genera of colonic bacteria. The mechanisms of the beneficial impacts of prebiotics on human health are very difficult to specify directly, because their health-promoting functions are related to fermentation by intestinal microflora. The impact of prebiotics on diet-related diseases in many ways also depends on the products of their fermentation. Prebiotics as functional food ingredients also have an impact on the quality of food products, due to their textural and gelling properties. Prebiotics as food additives can be very valuable in the creation of functional food aimed at preventing or postponing many diet-related diseases. They additionally have beneficial technological properties which improve the quality of food products.

Placebo effect of an inert gel on experimentally induced leg muscle pain

Directory of Open Access Journals (Sweden)

James G Hopker

2010-11-01

Full Text Available James G Hopker1, Abigail J Foad2, Christopher J Beedie2, Damian A Coleman2, Geoffrey Leach11Centre for Sports Studies, University of Kent, Chatham, Kent, UK; 2Department of Sports Science, Tourism and Leisure, Canterbury Christ Church University, Canterbury, Kent, UKPurpose: This study examined the therapeutic effects of an inert placebo gel on experimentally induced muscle pain in a sports therapy setting. It aimed to investigate the degree to which conditioned analgesia, coupled with an expectation of intervention, was a factor in subsequent analgesia.Methods: Participants were sixteen male and eight female sports therapy students at a UK University. With institutional ethics board approval and following informed consent procedures, each was exposed to pain stimulus in the lower leg in five conditions, ie, conditioning, prebaseline, experimental (two placebo gel applications, and postbaseline. In conditioning trials, participants identified a level of pain stimulus equivalent to a perceived pain rating of 6/10. An inert placebo gel was then applied to the site with the explicit instruction that it was an analgesic. Participants were re-exposed to the pain stimulus, the level of which, without their knowledge, had been decreased, creating the impression of an analgesic effect resulting from the gel. In experimental conditions, the placebo gel was applied and the level of pain stimulus required to elicit a pain rating of 6/10 recorded.Results: Following application of the placebo gel, the level of pain stimulus required to elicit a pain rating of 6/10 increased by 8.2%. Application of the placebo gel significantly decreased participant’s perceptions of muscle pain (P = 0.001.Conclusion: Subjects’ experience and expectation of pain reduction may be major factors in the therapeutic process. These factors should be considered in the sports therapeutic environment.Keywords: conditioning, expectation, perception, positive belief, sports therapy

Endotracheal tube resistance and inertance in a model of mechanical ventilation of newborns and small infants—the impact of ventilator settings on tracheal pressure swings

International Nuclear Information System (INIS)

Hentschel, Roland; Buntzel, Julia; Guttmann, Josef; Schumann, Stefan

2011-01-01

Resistive properties of endotracheal tubes (ETTs) are particularly relevant in newborns and small infants who are generally ventilated through ETTs with a small inner diameter. The ventilation rate is also high and the inspiratory time (ti) is short. These conditions effectuate high airway flows with excessive flow acceleration, so airway resistance and inertance play an important role. We carried out a model study to investigate the impact of varying ETT size, lung compliance and ventilator settings, such as peak inspiratory pressure (PIP), positive end expiratory pressure (PEEP) and inspiratory time (ti) on the pressure–flow characteristics with respect to the resistive and inertive properties of the ETT. Pressure at the Y piece was compared to direct measurement of intratracheal pressure (P trach ) at the tip of the ETT, and pressure drop (ΔP ETT ) was calculated. Applying published tube coefficients (Rohrer's constants and inertance), P trach was calculated from ventilator readings and compared to measured P trach using the root-mean-square error. The most relevant for ΔP ETT was the ETT size, followed by (in descending order) PIP, compliance, ti and PEEP, with gas flow velocity being the principle in common for all these parameters. Depending on the ventilator settings ΔP ETT exceeded 8 mbar in the smallest 2.0 mm ETT. Consideration of inertance as an additional effect in this setting yielded a better agreement of calculated versus measured P trach than Rohrer's constants alone. We speculate that exact tracheal pressure tracings calculated from ventilator readings by applying Rohrer's equation and the inertance determination to small size ETTs would be helpful. As an integral part of ventilator software this would (1) allow an estimate of work of breathing and implementation of an automatic tube compensation, and (2) be important for gentle ventilation in respiratory care, especially of small infants, since it enables the physician to

Experimental observations of effects of inert gas on cavity formation during irradiation

International Nuclear Information System (INIS)

Farrell, K.

1980-04-01

Cavity (void) formation and swelling in non-fissile materials during neutron irradiation and charged particle bombardments are reviewed. Helium is the most important inert gas and is primarily active as a cavity nucleant. It also enhances formation of dislocation structure. Preimplantation of helium overstimulates cavity nucleation and gives a different temperature response of swelling than when helium is coimplanted during the damage process. Helium affects, and is affected by, radiation-induced phase instability. Many of these effects are explainable in terms of cavity nucleation on submicroscopic critical size gas bubbles, and on the influence of the neutral sink strength of such bubbles. Titanium and zirconium resist cavity formation when vacancy loops are present

Experimental observations of effects of inert gas on cavity formation during irradiation

Energy Technology Data Exchange (ETDEWEB)

Farrell, K.

1980-04-01

Cavity (void) formation and swelling in non-fissile materials during neutron irradiation and charged particle bombardments are reviewed. Helium is the most important inert gas and is primarily active as a cavity nucleant. It also enhances formation of dislocation structure. Preimplantation of helium overstimulates cavity nucleation and gives a different temperature response of swelling than when helium is coimplanted during the damage process. Helium affects, and is affected by, radiation-induced phase instability. Many of these effects are explainable in terms of cavity nucleation on submicroscopic critical size gas bubbles, and on the influence of the neutral sink strength of such bubbles. Titanium and zirconium resist cavity formation when vacancy loops are present.

Nutrient digestibility in food waste ingredients for Pekin and Muscovy ducks.

Science.gov (United States)

Farhat, A; Normand, L; Chavez, E R; Touchburn, S P

1998-09-01

Food wastes are valuable resources to be recycled into new added-value products through animal production. The determination of energy and digestibility values of these wastes is essential for feed formulation. Corn, soybean meal (SBM), and a total of nine industrial food waste ingredients were tested in a comparative metabolic study in Pekin and Muscovy ducklings at two different ages during growth. The "precision-feeding" technique was employed to establish DM, fat, and fiber digestibility as well as retention of N and energy (AME, AMEn in Pekins; and AME, AMEn, TME, TMEn in Muscovies) for the 11 ingredients. For Pekin at 3 wk of age, the AMEn of peanuts, tofu, pogo, granola, waste diet, bread, corn, SBM, okara, and brewers grains were 5,141, 4,019, 3,971, 3,908, 3,141, 2,279, 1,572, and 1,442 kcal/kg, respectively. For Pekin at 6 wk of age, the AMEn of peanuts, pogo, tofu, granola, waste diet, bread, corn, SBM, and okara were 5,340, 4,327, 4,254, 4,079, 3,567, 3,302, 3,201, 2,416, and 1,562 kcal/kg, respectively. For Muscovy at 7 wk of age, the TMEn of peanuts, pogo, granola, waste diet, corn, tofu, bread, SBM, okara, and peanut skin were 5,207, 4,321, 4,057, 3,733, 3,233, 3,180, 3,084, 2,236, 1,575, and 904 kcal/kg, respectively. For Muscovy at 11 wk of age, the TMEn of peanuts, pogo, granola, tofu, waste diet, corn, bread, SBM, okara, and brewers grains were 5,077, 4,137, 4,025, 3,921, 3,586, 3,254, 3,123, 2,245, 2,007, and 1,392 kcal/kg, respectively. Nitrogen retention was significantly (P waste diet and lower for bread, corn, granola, brewers grains, and peanut skin. Dry matter digestibility was high for granola, pogo, corn, bread, and the food waste diet. Fat digestibility was generally the same for all the ingredients and was consistently over 97%. Bread neutral detergent fiber (NDF) was significantly (P waste ingredients as well as corn and SBM in both Pekin and Muscovy ducklings at two different ages during growth to market weight.

Transforming beef by-products into valuable ingredients: which spell/recipe to use?

Directory of Open Access Journals (Sweden)

Maeve Mary Henchion

2016-11-01

Full Text Available Satisfying the increasing global demand for protein results in challenges from a supply perspective. Increased use of animal proteins, through greater use of meat by-products, could form part of the solution, subject to consumer acceptance. This research investigates consumer evaluations of food products that incorporate ingredients derived from offals that have been produced through a range of food processing technologies. Using focus groups incorporating product stimuli representing various combinations of offals, processing and carrier products, the research finds that the physical state and perceived naturalness of the ingredients influences acceptance. It also highlights the impact of life experiences, linked to demographic characteristics, on interpretations and evaluations of products and processes. Ideational influences, i.e. knowledge of the nature or origin of the substance, are reasons for rejecting some concepts, with misalignment between nature of processing and the product resulting in rejection of others. Lack of perceived necessity also results in rejection. Alignment of ingredients with existing culinary practices and routines, communication of potential sensory or other benefits as well as naturalness are factors likely to promote acceptance, and generate repeat purchase, in some consumer segments. Trust in oversight that the products are safe is a prerequisite for acceptance in all cases. These findings have implications for pathways to increase sustainability of beef production and consumption through increased use of beef by-products.

Measurements of the acid-binding capacity of ingredients used in pig diets

Directory of Open Access Journals (Sweden)

Lawlor Peadar G

2005-08-01

Full Text Available Some feed ingredients bind more acid in the stomach than others and for this reason may be best omitted from pig starter foods if gastric acidity is to be promoted. The objective of this study was to measure the acid-binding capacity (ABC of ingredients commonly used in pig starter foods. Ingredients were categorised as follows: (i milk products (n = 6, (ii cereals (n = 10, (iii root and pulp products (n = 5, (iv vegetable proteins (n = 11, (v meat and fish meal (n = 2, (vi medication (n = 3, (vii amino acids (n = 4, (viii minerals (n = 16, (ix acid salts (n = 4, (x acids (n = 10. A 0.5 g sample of food was suspended in 50 ml distilled de-ionised water with continuous stirring. This suspension was titrated with 0.1 mol/L HCl or 0.1 mol/L NaOH so that approximately 10 additions of titrant was required to reach pH 3.0. The pH readings after each addition were recorded following equilibration for three minutes. ABC was calculated as the amount of acid in milliequivalents (meq required to lower the pH of 1 kg food to (a pH 4.0 (ABC-4 and (b pH 3.0 (ABC-3. Categories of food had significantly different (P

Aluminothermic Reduction-Molten Salt Electrolysis Using Inert Anode for Oxygen and Al-Base Alloy Extraction from Lunar Soil Simulant

Science.gov (United States)

Xie, Kaiyu; Shi, Zhongning; Xu, Junli; Hu, Xianwei; Gao, Bingliang; Wang, Zhaowen

2017-10-01

Aluminothermic reduction-electrolysis using an inert anode process is proposed to extract oxygen and metals from Minnesota Lunar Simulant-1 (MLS-1). Effective aluminothermic reduction between dissolved MLS-1 and dissolved metal aluminum was achieved in cryolite salt media. The product phases obtained by aluminothermic reduction at 980°C for 4 h were Al, Si, and Al5FeSi, while the chemical components were 79.71 mass% aluminum, 12.03 mass% silicon, 5.91 mass% iron, and 2.35 mass% titanium. The cryolite salt containing Al2O3 was subsequently electrolyzed with Fe0.58-Ni0.42 inert anode at 960°C for 4 h. Oxygen was evolved at the anode with an anodic current efficiency of 78.28%. The results demonstrate that this two-step process is remarkably feasible for the extraterrestrial extraction of oxygen and metals. This process will help expand the existing in situ resource utilization methods.

Legumes as Functional Ingredients in Gluten-Free Bakery and Pasta Products.

Science.gov (United States)

Foschia, Martina; Horstmann, Stefan W; Arendt, Elke K; Zannini, Emanuele

2017-02-28

The increasing demand for gluten-free food products from consumers has triggered food technologists to investigate a wide range of gluten-free ingredients from different sources to reproduce the unique network structure developed by gluten in a wheat-dough system. In recent times, the attention has been focused on novel application of legume flour or ingredients. The interest in this crop category is mainly attributed to their functional properties, such as solubility and water-binding capacity, which play an important role in gluten-free food formulation and processing. Their nutritional profile may also counteract the lack of nutrients commonly highlighted in commercial gluten-free bakery and pasta products, providing valuable sources of protein, dietary fiber, vitamins, minerals, and complex carbohydrates, which in turn have a positive impact on human health. This review reports the main chemical and functional characteristics of legumes and their functional application in gluten-free products.

An in vitro lung model to assess true shunt fraction by multiple inert gas elimination.

Directory of Open Access Journals (Sweden)

Balamurugan Varadarajan

Full Text Available The Multiple Inert Gas Elimination Technique, based on Micropore Membrane Inlet Mass Spectrometry, (MMIMS-MIGET has been designed as a rapid and direct method to assess the full range of ventilation-to-perfusion (V/Q ratios. MMIMS-MIGET distributions have not been assessed in an experimental setup with predefined V/Q-distributions. We aimed (I to construct a novel in vitro lung model (IVLM for the simulation of predefined V/Q distributions with five gas exchange compartments and (II to correlate shunt fractions derived from MMIMS-MIGET with preset reference shunt values of the IVLM. Five hollow-fiber membrane oxygenators switched in parallel within a closed extracorporeal oxygenation circuit were ventilated with sweep gas (V and perfused with human red cell suspension or saline (Q. Inert gas solution was infused into the perfusion circuit of the gas exchange assembly. Sweep gas flow (V was kept constant and reference shunt fractions (IVLM-S were established by bypassing one or more oxygenators with perfusate flow (Q. The derived shunt fractions (MM-S were determined using MIGET by MMIMS from the retention data. Shunt derived by MMIMS-MIGET correlated well with preset reference shunt fractions. The in vitro lung model is a convenient system for the setup of predefined true shunt fractions in validation of MMIMS-MIGET.

Tracheal volume in the pupa of the Saturniid moth Hyalophora cecropia determined with inert gases.

Science.gov (United States)

Bridges, C R; Kestler, P; Scheid, P

1980-06-01

Tracheal volume (VTr) was measured in pupae of the Giant silkworm moth Hyalophora cecropia (Saturniidae, Lepidoptera, Insecta) using inert gas wash-out techniques. The animal was placed in a small vessel that was continuously ventilated (rate, V) by a gas mixture containing 20% O2 in N2; the inflowing (F1) and outflowing gas fractions (FE) of the vessel could be continuously measured by a respiratory mass spectrometer. At the onset of a spiracular constriction period, which was evidenced from the FECO2 trace, the mixture was rapidly replaced by pure Ar. At the subsequent burst, the amount of N2 emerging from the animal, MN2, was calculated from V and the difference (FE--F1)N2. VTr was calculated from MN2 and the N2 concentration in the tracheal system before constriction (assumed to equal that in the ventilating gas before replacement by Ar). Measurements were repeated with N2 and Ar replacing each other. VTr average 48 microliter . g-1 (range 39 to 59) for animals of 5.8 g average body weight (range 3.4 to 9.9), when inert gas solubility in body fluids was accounted for. Both size and stage in pupal development appear to affect VTr. These values show reasonable agreement with literature data, mostly obtained by emptying the tracheal gas space by mechanical compression.

Fermented Brown Rice Flour as Functional Food Ingredient

OpenAIRE

Ilowefah, Muna; Chinma, Chiemela; Bakar, Jamilah; Ghazali, Hasanah; Muhammad, Kharidah; Makeri, Mohammad

2014-01-01

As fermentation could reduce the negative effects of bran on final cereal products, the utilization of whole-cereal flour is recommended, such as brown rice flour as a functional food ingredient. Therefore, this study aimed to investigate the effect of fermented brown rice flour on white rice flour, white rice batter and its steamed bread qualities. Brown rice batter was fermented using commercial baker?s yeast (Eagle brand) according to the optimum conditions for moderate acidity (pH 5.5) to...

Thermal Analysis of Solid Fuels in an Inert Atmosphere

Science.gov (United States)

Kijo-Kleczkowska, Agnieszka; Szumera, Magdalena; Środa, Katarzyna

2017-12-01

The paper takes the analysis of thermal studies of different types of fuels. It allowed diversification of fuels depending on their composition and origin. Consideration of coal, biomass and waste (coal mule, sewage sludge) as fuel is nowadays an important aspect of energy in our country. It should be emphasized that Poland power engineering is based up to 95% on coal - the primary fuel. Mining industry, forced to deliver power engineering more and better fuel, must however, use a deeper cleaning of coal. This results in a continuous increase waste in the form of mule flotation. The best method of disposing these mule is combustion and co-combustion with other fuels. On the other hand, commonly increasing awareness state of the environment and the need to reduce CO2 emissions energy industry have committed to implement alternative solutions in order to gain power, through, i.a.: development technologies use of biomass, which is one of the most promising renewable energy sources in Poland. The paper presents the results of research TG-DTA fuels made in an inert atmosphere.

Survival of viral pathogens in animal feed ingredients under transboundary shipping models

Science.gov (United States)

Bauermann, Fernando V.; Niederwerder, Megan C.; Singrey, Aaron; Clement, Travis; de Lima, Marcelo; Long, Craig; Patterson, Gilbert; Sheahan, Maureen A.; Stoian, Ana M. M.; Petrovan, Vlad; Jones, Cassandra K.; De Jong, Jon; Ji, Ju; Spronk, Gordon D.; Minion, Luke; Christopher-Hennings, Jane; Zimmerman, Jeff J.; Rowland, Raymond R. R.; Nelson, Eric; Sundberg, Paul; Diel, Diego G.

2018-01-01

The goal of this study was to evaluate survival of important viral pathogens of livestock in animal feed ingredients imported daily into the United States under simulated transboundary conditions. Eleven viruses were selected based on global significance and impact to the livestock industry, including Foot and Mouth Disease Virus (FMDV), Classical Swine Fever Virus (CSFV), African Swine Fever Virus (ASFV), Influenza A Virus of Swine (IAV-S), Pseudorabies virus (PRV), Nipah Virus (NiV), Porcine Reproductive and Respiratory Syndrome Virus (PRRSV), Swine Vesicular Disease Virus (SVDV), Vesicular Stomatitis Virus (VSV), Porcine Circovirus Type 2 (PCV2) and Vesicular Exanthema of Swine Virus (VESV). Surrogate viruses with similar genetic and physical properties were used for 6 viruses. Surrogates belonged to the same virus families as target pathogens, and included Senecavirus A (SVA) for FMDV, Bovine Viral Diarrhea Virus (BVDV) for CSFV, Bovine Herpesvirus Type 1 (BHV-1) for PRV, Canine Distemper Virus (CDV) for NiV, Porcine Sapelovirus (PSV) for SVDV and Feline Calicivirus (FCV) for VESV. For the remaining target viruses, actual pathogens were used. Virus survival was evaluated using Trans-Pacific or Trans-Atlantic transboundary models involving representative feed ingredients, transport times and environmental conditions, with samples tested by PCR, VI and/or swine bioassay. SVA (representing FMDV), FCV (representing VESV), BHV-1 (representing PRV), PRRSV, PSV (representing SVDV), ASFV and PCV2 maintained infectivity during transport, while BVDV (representing CSFV), VSV, CDV (representing NiV) and IAV-S did not. Notably, more viruses survived in conventional soybean meal, lysine hydrochloride, choline chloride, vitamin D and pork sausage casings. These results support published data on transboundary risk of PEDV in feed, demonstrate survival of certain viruses in specific feed ingredients (“high-risk combinations”) under conditions simulating transport between

The Chemistry of Curcumin, the Health Promoting Ingredient in Turmeric

Science.gov (United States)

Dewprashad, Brahmadeo

2010-01-01

Case studies pertaining to the health benefits of foods can be particularly effective in engaging students and in teaching core concepts in science (Heidemann and Urquart 2005). This case study focuses on the chemistry of curcumin, the health-promoting ingredient in turmeric. The case was developed to review core concepts in organic chemistry and…

Standardized Ileal Amino Acid Digestibility of Commonly Used Feed Ingredients in Growing Broilers

Science.gov (United States)

Ullah, Zafar; Ahmed, Gulraiz; Nisa, Mehr un; Sarwar, Muhammad

2016-01-01

This experiment was conducted to determine standardized ileal amino acid digestibility (SIAAD) of commonly used feed ingredients in poultry diets in Pakistan. These feed ingredients included corn, rice broken (RB), rice polishings (RP), wheat bran (WB), sunflower meal (SFM), cottonseed meal (CSM), guar meal (GM), soybean meal (SBM) from India and Argentine and fish meal (FM). The SIAAD of each ingredient was determined in triplicate using 21-days-old broilers. Day-old male broiler chicks (Hubbard× Hubbard) were reared on corn-SBM based diet from 1 to 13 days and thereafter birds were fed experimental diets from day 14 to 21. Each diet was fed to 36 birds kept in six replicate cages, each cage had six birds. In cereals, the SIAAD of corn’s amino acid (AA) (90.1%) was similar (p>0.05) to RB (89.0%). Isoleucine (97.8%) and lysine (96.9%) were highly digestible AA in corn and RB, respectively. Among cereal-by products, WB’s SIAAD (76.9%) was same (p>0.05) as RP (71.9%). Arginine from WB (82.5%) and RP (83.2%) was highly digestible. However, threonine in WB (72.7%) and leucine in RP (69.6%) were the lowest digestible AAs. In plant protein meals, AAs from Argentine-SBM (85.1%) and Indian-SBM (83.4%) had higher (pdigestible from indispensable AAs. In SFM, methionine (91.4%) SIAAD was the greatest. The average SIAAD of FM was 77.6%. Alanine from FM had the highest (84.0%) but cysteine (62.8%) had the lowest SIAAD. In conclusion, cereals i.e. corn and RB had higher (p0.05). The SBM from plant protein meals had higher (p<0.05) SIAAD than other studied feed ingredients. However, the GM had the lowest (p<0.05) SIAAD among protein meals. PMID:26954227

Effect of penetration modifiers on the dermal and transdermal delivery of drugs and cosmetic active ingredients.

Science.gov (United States)

Otto, A; Wiechers, J W; Kelly, C L; Hadgraft, J; du Plessis, J

2008-01-01

In this study the effect of 2 penetration modifiers, dimethyl isosorbide (DMI) and diethylene glycol monoethyl ether (DGME) on the skin delivery of hydroquinone (HQ), salicylic acid (SA) and octadecenedioic acid (DIOIC) was investigated. Ten percent DMI and DGME were separately formulated into oil-in-water emulsions containing 1.8% HQ, SA and DIOIC, respectively. Skin delivery and the flux across split-thickness human skin of the active ingredients were determined using Franz diffusion cells. An emulsion with 10% water incorporated instead of the water-soluble penetration modifiers served as a control. The study showed that neither 10% DMI nor 10% DGME significantly enhanced the skin permeation of the various lipophilic active ingredients or the uptake into the skin. It was hypothesized that the addition of the penetration modifiers to the emulsions not only enhanced the solubility of the various active ingredients in the skin but also in the formulation, resulting in a reduced thermodynamic activity and hence a weaker driving force for penetration. Therefore, the effect of DMI and DGME on the solubility of the active ingredients in the skin was counteracted by a simultaneous reduction in the thermodynamic activity in the formulation. Copyright 2008 S. Karger AG, Basel.

Hydroxytyrosol: Health Benefits and Use as Functional Ingredient in Meat

Directory of Open Access Journals (Sweden)

Lorena Martínez

2018-01-01

Full Text Available Hydroxytyrosol (HXT is a phenolic compound drawn from the olive tree and its leaves as a by-product obtained from the manufacturing of olive oil. It is considered the most powerful antioxidant compound after gallic acid and one of the most powerful antioxidant compounds between phenolic compounds from olive tree followed by oleuropein, caffeic and tyrosol. Due to its molecular structure, its regular consumption has several beneficial effects such as antioxidant, anti-inflammatory, anticancer, and as a protector of skin and eyes, etc. For these reasons, the use of HXT extract is a good strategy for use in meat products to replace synthetics additives. However, this extract has a strong odour and flavour, so it is necessary to previously treat this compound in order to not alter the organoleptic quality of the meat product when is added as ingredient. The present review exposes the health benefits provided by HXT consumption and the latest research about its use on meat. In addition, new trends about the application of HXT in the list of ingredients of healthier meat products will be discussed.

Hydroxytyrosol: Health Benefits and Use as Functional Ingredient in Meat.

Science.gov (United States)

Martínez, Lorena; Ros, Gaspar; Nieto, Gema

2018-01-23

Hydroxytyrosol (HXT) is a phenolic compound drawn from the olive tree and its leaves as a by-product obtained from the manufacturing of olive oil. It is considered the most powerful antioxidant compound after gallic acid and one of the most powerful antioxidant compounds between phenolic compounds from olive tree followed by oleuropein, caffeic and tyrosol. Due to its molecular structure, its regular consumption has several beneficial effects such as antioxidant, anti-inflammatory, anticancer, and as a protector of skin and eyes, etc. For these reasons, the use of HXT extract is a good strategy for use in meat products to replace synthetics additives. However, this extract has a strong odour and flavour, so it is necessary to previously treat this compound in order to not alter the organoleptic quality of the meat product when is added as ingredient. The present review exposes the health benefits provided by HXT consumption and the latest research about its use on meat. In addition, new trends about the application of HXT in the list of ingredients of healthier meat products will be discussed.

[Application of FT-IR pattern recognition method for the quality control of pharmaceutical ingredients].

Science.gov (United States)

Horgos, József; Kóger, Péter; Zelkó, Romána

2009-01-01

Nowadays infrared spectroscopy and chemometrics have proven their effectiveness for both qualitative and quantitative analyses in different fields like agriculture, food, chemical and oil industry. Furier Transformation Infrared Spectroscopy (FT-IR) combined with Attenuated Total Reflectance (ATR) plate is a fast identification instrument. It is suitable for analysis of solid and liquid phase, too. Associated with chemometrics, it would be a powerful tool for the pharmaceutical wholesalers to detect the insufficient quality of pharmaceutical ingredients. In the present study beside the review of the infra red technology, pharmaceutical ingredients were examined with the help of our spectra library.

Disposição em aterros controlados de resíduos sólidos industriais não-inertes: avaliação dos componentes tóxicos e implicações para o ambiente e para a saúde humana Non-inert industrial solid waste disposal in landfill dumps: evaluation of toxicity and implications for the environment and human health

Directory of Open Access Journals (Sweden)

Cristina L. S. Sisinno

2003-04-01

Full Text Available Para que um resíduo sólido seja disposto adequadamente, é necessário classificá-lo segundo as Normas Técnicas Brasileiras, cuja principal é a NBR 10.004. Resíduos sólidos industriais não-inertes normalmente têm sido encaminhados para disposição final em aterros controlados, que em sua maioria não operam de forma eficiente, além de estarem geralmente localizados próximos a núcleos populacionais e ecossistemas importantes. A fim de avaliar a toxicidade potencial dos resíduos produzidos em indústrias de diferentes segmentos, 21 amostras foram analisadas de acordo com as orientações descritas na NBR 10.004. Das amostras estudadas, 18 foram classificadas como resíduos não-inertes. Os principais parâmetros que contribuíram para a classificação das amostras em resíduos não-inertes foram: alumínio, ferro, manganês, fenol e surfactantes. Destes, o alumínio, o manganês e o fenol são as substâncias de maior interesse toxicológico para a saúde humana e ambiental, uma vez que podem alterar a qualidade das águas subterrâneas localizadas nas áreas de disposição de resíduos.According to Brazilian recommended technical procedures (mainly NBR 10,004, solid waste must be previously classified in order to be disposed of adequately. Non-inert industrial solid waste is being dumped in landfill areas, most of which operate inefficiently and are located near the population and important ecosystems. In order to evaluate the potential toxicity of solid waste produced by various types of industries, 21 samples were analyzed according to NBR 10,004 procedures. Of these, 18 were classified as non-inert solid waste. The main substances contributing to the classification of these samples as non-inert waste were: aluminum, iron, manganese, phenol, and surfactants. Aluminum, manganese, and phenol are the main toxicologically relevant substances for human and environmental health because they can alter the quality of groundwater

Eight previously unidentified mutations found in the OA1 ocular albinism gene

Directory of Open Access Journals (Sweden)

Dufier Jean-Louis

2006-04-01

Full Text Available Abstract Background Ocular albinism type 1 (OA1 is an X-linked ocular disorder characterized by a severe reduction in visual acuity, nystagmus, hypopigmentation of the retinal pigmented epithelium, foveal hypoplasia, macromelanosomes in pigmented skin and eye cells, and misrouting of the optical tracts. This disease is primarily caused by mutations in the OA1 gene. Methods The ophthalmologic phenotype of the patients and their family members was characterized. We screened for mutations in the OA1 gene by direct sequencing of the nine PCR-amplified exons, and for genomic deletions by PCR-amplification of large DNA fragments. Results We sequenced the nine exons of the OA1 gene in 72 individuals and found ten different mutations in seven unrelated families and three sporadic cases. The ten mutations include an amino acid substitution and a premature stop codon previously reported by our team, and eight previously unidentified mutations: three amino acid substitutions, a duplication, a deletion, an insertion and two splice-site mutations. The use of a novel Taq polymerase enabled us to amplify large genomic fragments covering the OA1 gene. and to detect very likely six distinct large deletions. Furthermore, we were able to confirm that there was no deletion in twenty one patients where no mutation had been found. Conclusion The identified mutations affect highly conserved amino acids, cause frameshifts or alternative splicing, thus affecting folding of the OA1 G protein coupled receptor, interactions of OA1 with its G protein and/or binding with its ligand.

Thermoluminescence analysis can identify irradiated ingredient in soy sauce before and after pasteurization

International Nuclear Information System (INIS)

Lee, Jeong-Eun; Sanyal, Bhaskar; Akram, Kashif; Jo, Yunhee; Baek, Ji-Yeong; Kwon, Joong-Ho

2017-01-01

Thermoluminescence (TL) analysis was conducted to identify small quantities (0.5%, 1%, and 1.5%) of γ ray-or electron beam-irradiated garlic powder in a soy sauce after commercial pasteurization. The sauce samples with γ ray- and electron beam-irradiated (0, 1 or 10 kGy) garlic powder showed detectable TL glow curves, characterized by radiation-induced maximum in the temperature range of 180–225 °C. The successful identification of soy sauces with an irradiation history was dependent on both the mixing ratio of the irradiated ingredient and the irradiation dose. Post-irradiation pasteurization (85 °C, 30 min) caused no considerable changes in TL glow shape or intensity. Interlaboratory tests demonstrated that the shape and intensity of the first TL glow curve (TL1) could be a better detection marker than a TL ratio (TL1/TL2). - Highlights: • Thermoluminescence (TL) characteristics were studied to identify irradiated ingredient in soy sauce. • TL emission was found to be dependent on irradiation doses and blending ratios of the ingredients. • TL technique was found to be successful in detecting irradiation status even after pasteurization. • Inter-laboratory trial gave a clear verdict on irradiation detection potential of TL technique.

Network synthesis and parameter optimization for vehicle suspension with inerter

Directory of Open Access Journals (Sweden)

Long Chen

2016-12-01

Full Text Available In order to design a comfortable-oriented vehicle suspension structure, the network synthesis method was utilized to transfer the problem into solving a timing robust control problem and determine the structure of “inerter–spring–damper” suspension. Bilinear Matrix Inequality was utilized to obtain the timing transfer function. Then, the transfer function of suspension system can be physically implemented by passive elements such as spring, damper, and inerter. By analyzing the sensitivity and quantum genetic algorithm, the optimized parameters of inerter–spring–damper suspension were determined. A quarter-car model was established. The performance of the inerter–spring–damper suspension was verified under random input. The simulation results manifested that the dynamic performance of the proposed suspension was enhanced in contrast with traditional suspension. The root mean square of vehicle body acceleration decreases by 18.9%. The inerter–spring–damper suspension can inhibit the vertical vibration within the frequency of 1–3 Hz effectively and enhance the performance of ride comfort significantly.

Removal of the Inert Organic Fraction of Municipal Wastewater Using the Integrated Activated Sludge/Trickling Filter System

Directory of Open Access Journals (Sweden)

mehraban sadeghi

2015-01-01

Full Text Available The discharge of phenol and chlorinated compounds, fatty acids, tannin, lignin, and their by-products into receptive waters poses serious hazards for the aquatic life. In this study, the efficiency of a tow-step process of activated sludge-trickling filter (AS/TF in the removal of inert chemical materials that defy conventional treatment processes was investigated. For this purpose, an integrated activated sludge process (industrial scale was used sequentially with a trickling filter (pilot scale. Inside a tank with an effective volume of 6.87 m3 was installed 5.78 m3 of polypropylene 2HX media with a specific area of 240 m2/m3. The hydraulic loading rate (HLR of the trickling filter during the startup period (90 days was 3.6 m3/h which was raised to 3.6-6 m3/h in the operation period (120 days, with the best effluent quality achieved at HLR=5.4 m3/h. For the purposes of the experiments in this study, four reactors, each 1256 cm3 in volume, were fed the WWTP effluent and concurrently a glucose substrate containing a COD content equal to that fed to the four reactors was fed into two identical reactors; all the reactors were subsequently run for 480 h in aerobic conditions. Nutrients, pH, and DO (as environmental control indicators as well as soluble and total COD were measured twice daily. The effluent values of soluble inert materials (SI, total soluble COD (STO, degradable suspended materials (XSO, degradable COD (CSO, refractory suspended materials (XI, and degradable soluble materials (SSO for AS were calculated as 40, 227, 94, 281, 251, and 187, respectively, while the same parameters for the AS/TF were 20, 227, 104, 311, 241, and 207 mg/l, respectively. The results showed that the activated sludge process when combined with the trickling filter has a twofold capability, compared to when used alone, in removing inert COD. It was also shown that treatment levels in conventional WWTPs can be improved by integrating conventional treatment

Inert annealing of irradiated graphite by inductive heating

International Nuclear Information System (INIS)

Botzem, W.; Woerner, J.

2001-01-01

Fission neutrons change physical properties of graphite being used in nuclear reactors as moderator and as structural material. The understanding of these effects on an atomic model is expressed by dislocations of carbon atoms within the graphite and the thereby stored energy is known as Wigner Energy. The dismantling of the Pile 1 core may necessitate the thermal treatment of the irradiated but otherwise undamaged graphite. This heat treatment - usually called annealing - initiates the release of stored Wigner Energy in a controlled manner. This energy could otherwise give rise to an increase in temperature under certain conditions during transport or preparation for final storage. In order to prevent such an effect it is intended to anneal the major part of Pile 1 graphite before it is packed into boxes suitable for final disposal. Different heating techniques have been assessed. Inductive heating in an inert atmosphere was selected for installation in the Pile 1 Waste Processing Facility built for the treatment and packaging of the dismantled Pile 1 waste. The graphite blocks will be heated up to 250 deg. C in the annealing ovens, which results in the release of significant amount of the stored energy. External heat sources in a final repository will never heat up the storage boxes to such a temperature. (author)

Influence of different functional ingredients on physical properties, rheology, tribology, and oral perceptions of no fat stirred yoghurt.

Science.gov (United States)

Ng, Sophia Bao Xian; Nguyen, Phuong T M; Bhandari, Bhesh; Prakash, Sangeeta

2018-06-01

Effects of adding four functional ingredients: inulin, pectin, galacto-oligosaccharides (GOS), and beta glucan on physical, rheology, tribology, and sensory characteristics of skim (0.1% fat) stirred yoghurt were studied. Three levels of each ingredient were chosen: inulin (7, 8, and 9%), pectin (0.2, 0.25, and 0.3%), GOS (9.1, 11.3, and 13.6%), and beta glucan (0.1, 0.2, and 0.3%). Among the investigated ingredients, inulin and GOS appeared to be preferable choices due to their ability to both reduce syneresis and slightly increase sample lubrication while maintaining texture, rheology, and sensory characteristics of skim yoghurt. Pectin and beta glucan, conversely, increased viscosity and gel strength, slightly increased sample lubrication for the skim yoghurt but created large particles (i.e., greater than 100 μm) in the product body. This led to the increase in lumpiness and residual coating while reducing smoothness and creaminess of the sample. The observed tribology behaviors of the stirred yoghurts were similar to the previous study of pot-set yoghurt whose friction curves comprised four friction zones (Nguyen, Kravchuk, Bhandari, and Prakash). The sensory characteristics of six selected samples for various texture and mouthfeel attributes obtained from a trained panel were in agreement with particle size, rheology, and tribology characteristics of the yoghurt samples. With the increasing demand for low fat and functional food, there is a need to understand the impact of adding functional ingredients in low fat yoghurt to satisfy consumers' requirements. This study investigates the effects of these functional ingredients at different dosages on physical, rheology, tribology, and sensory characteristics of skim (0.1% fat) stirred yoghurt. The results from this study may guide use of functional ingredients in yoghurt production. © 2017 Wiley Periodicals, Inc.

Active flux tungsten inert gas welding of austenitic stainless steel AISI 304

Directory of Open Access Journals (Sweden)

D. Klobčar

2016-10-01

Full Text Available The paper presents the effects of flux assisted tungsten inert gas (A-TIG welding of 4 (10 mm thick austenitic stainless steel EN X5CrNi1810 (AISI 304 in the butt joint. The sample dimensions were 300 ´ 50 mm, and commercially available active flux QuickTIG was used for testing. In the planned study the influence of welding position and weld groove shape was analysed based on the penetration depth. A comparison of microstructure formation, grain size and ferrit number between TIG welding and A-TIG welding was done. The A-TIG welds were subjected to bending test. A comparative study of TIG and A-TIG welding shows that A-TIG welding increases the weld penetration depth.

A Urologist's Guide to Ingredients Found in Top-Selling Nutraceuticals for Men's Sexual Health.

Science.gov (United States)

Cui, Tao; Kovell, Robert C; Brooks, David C; Terlecki, Ryan P

2015-11-01

Use of supplements is common among men seeking urologic evaluation for sexual health matters. With a dizzying array of formulations available and little regulation on the dosage, purity, or ingredients found in these products, the health effects of nutraceuticals are often confusing to patients and medical practitioners alike. In this review, we set out to concisely summarize the data on ingredients found within the top-selling nutraceutical agents marketed for men's sexual health in order to provide a clinical guide for urologists. We used sales data from the most popular retail provider of men's health supplements to identify the top-selling products marketed toward improvement of men's sexual health. We summarized the available information related to the ingredients, dosage, cost, and mechanism of action for these substances and performed an extensive literature search to identify and review the current evidence available for each of the most common ingredients found in these nutraceuticals. The top-selling nutraceuticals marked for men's sexual health contain a blend of multiple supplements (up to 33 in one formulation identified), the most common being ginseng, tribulus, zinc, horny goat weed, B complex vitamins/trace minerals, fenugreek, L-arginine, maca, DHEA, ginkgo, and yohimbine. The currently available medical literature evaluating the efficacy of these substances is generally of low quality. Despite the dearth of evidence supporting nutraceutical agents in the men's health arena, these substances are still commonly used by patients. As these products can affect the health and well-being of men presenting to a urology clinic, a familiarity with commonly used agents can help the urologist appropriately counsel their patients. © 2015 International Society for Sexual Medicine.

The probabilistic model of the process mixing of animal feed ingredients into a continuous mixer-reactor

Directory of Open Access Journals (Sweden)

L. I. Lytkina

2016-01-01

Full Text Available A mathematical model of the polydisperse medium mixing process reflects its stochastic features in the form of uneven distribution of phase elements on the time of their presence in apparatus, particle size, ripple retention of the apparatus, random distribution of the material and thermal phase flows of the working volume, heterogeneity of the medium physical- and chemical properties, complicated by chemical reaction. For the mathematical description of the mixing process of animal feed ingredients in the presence of chemical reaction the system of differential equations of Academician V.V. Kafarov was used. Proposed by him hypothesis based on the theory of Markov’s processes stating that "any multicomponent mixture can be considered as the result of an iterative process of mixing the two components to achieve the desired uniformity of all the ingredients in the mixture" allows us to consider a process of mixing binary composition in a paddle mixer in the form of differential equations of two ingredients concentration numerous changes until it becomes a homogenous mixture. It was found out that the mixing process of the two-component mixture is determined in a paddle mixer with a constant mixing speed and a limit (equilibrium dispersion of the ingredients in the mixture i.e. with its uniformity. Adjustment of the model parameters was carried out according to the results of experimental studies on mixing the crushed wheat with metallomagnetic impurity, which was a key (indicator component. According to the best values of the constant of the continuous mixing speed and the equilibrium disperse values of the ingredients contents, the mathematical model parameters identification was carried out. The results obtained are used to develop a new generation mixer design.

Antiviral Effects of Saffron and its Major Ingredients.

Science.gov (United States)

Soleymani, Sepehr; Zabihollahi, Rezvan; Shahbazi, Sepideh; Bolhassani, Azam

2018-01-01

The lack of an effective vaccine against viral infections, toxicity of the synthetic anti-viral drugs and the generation of resistant viral strains led to discover novel inhibitors. Recently, saffron and its compounds were used to treat different pathological conditions. In this study, we tested the anti-HSV-1 and anti-HIV-1 activities of Iranian saffron extract and its major ingredients including crocin and picrocrocin as well as cytotoxicity in vitro. The data showed that the aqueous saffron extract was not active against HIV-1 and HSV-1 virions at certain doses (i.e., a mild activity), but crocin and picrocrocin indicated significant anti-HSV-1 and also anti-HIV-1 activities. Crocin inhibited the HSV replication at before and after entry of virions into Vero cells. Indeed, crocin carotenoid suppressed HSV penetration in the target cells as well as disturbed virus replication after entry into the cells. Picrocrocin was also effective for inhibiting virus entry and also its replication. This monoterpen aldehyde showed higher anti-HSV effects after virus penetrating in the cells. Generally, these sugar-containing compounds extracted from saffron showed to be effective antiherpetic drug candidates. The recent study is the first report suggesting antiviral activities for saffron extract and its major ingredients. Crocin and picrocrocin could be a promising anti-HSV and anti-HIV agent for herbal therapy against viral infections. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

[Screening of anti-aging active ingredients and mechanism analysis based on molecular docking technology].

Science.gov (United States)

Du, Ran-Feng; Zhang, Xiao-Hua; Ye, Xiao-Tong; Yu, Wen-Kang; Wang, Yun

2016-07-01

Dampness evil is the source of all diseases, which is easy to cause disease and promote aging, while aging could also promote the occurence and development of diseases. In this paper, the relationship between the dampness evil and aging would be discussed, to find the anti-aging active ingredients in traditional Chinese medicine (TCM), and analyze the anti-aging mechanism of dampness eliminating drug. Molecular docking technology was used, with aging-related mammalian target of rapamycin as the docking receptors, and chemical components of Fuling, Sangzhi, Mugua, Yiyiren and Houpo as the docking molecules, to preliminarily screen the anti-aging active ingredients in dampness eliminating drug. Through the comparison with active drugs already on the market (temsirolimus and everolimus), 12 kinds of potential anti-aging active ingredients were found, but their drug gability still needs further study. The docking results showed that various components in the dampness eliminating drug can play anti-aging activities by acting on mammalian target of rapamycin. This result provides a new thought and direction for the method of delaying aging by eliminating dampness. Copyright© by the Chinese Pharmaceutical Association.

A systematic review on nanoencapsulation of food bioactive ingredients and nutraceuticals by various nanocarriers.

Science.gov (United States)

Assadpour, Elham; Jafari, Seid Mahdi

2018-06-08

Today, there is an ever-growing interest on natural food ingredients both by consumers and producers in the food industry. In fact, people are looking for those products in the market which are free from artificial and synthetic additives and can promote their health. These food bioactive ingredients should be formulated in such a way that protects them against harsh process and environmental conditions and safely could be delivered to the target organs and cells. Nanoencapsulation is a perfect strategy for this situation and there have been many studies in recent years for nanoencapsulation of food components and nutraceuticals by different technologies. In this review paper, our main goal is firstly to have an overview of nanoencapsulation techniques applicable to food ingredients in a systematic classification, i.e., lipid-based nanocarriers, nature-inspired nanocarriers, special-equipment-based nanocarriers, biopolymer nanocarriers, and other miscellaneous nanocarriers. Then, application of these cutting-edge nanocarriers for different nutraceuticals including phenolic compounds and antioxidants, natural food colorants, antimicrobial agents and essential oils, vitamins, minerals, flavors, fish oils and essential fatty acids will be discussed along with presenting some examples in each field.

Anti-bacteria effect of active ingredients of siraitia grosvenorii on the spoilage bacteria isolated from sauced pork head meat

Science.gov (United States)

Li, X.; Xu, L. Y.; Cui, Y. Q.; Pang, M. X.; Wang, F.; Qi, J. H.

2018-01-01

Extraction and anti-bacteria effect of active ingredients of Siraitia grosvenorii were studied in this paper. Extraction combined with ultrasonic was adopted. The optimum extraction condition was determined by single factor test; the anti-bacteria effect of active ingredients and minimum inhibitory concentration (MIC) were valued by Oxford-cup method. The results indicated that optimum extraction condition of active ingredients extracted from Siraitia grosvenorii were described as follows: ethanol concentrations of sixty-five percent and twenty minutes with ultrasonic assisted extraction; the active ingredients of Siraitia grosvenorii had anti-bacteria effect on Staphylococcus epidermidis, Proteus vulgaris, Bacillus sp, Serratia sp and MIC was 0.125g/mL, 0.0625g/mL, 0.125g/mL and 0.125g/mL. The active constituent of Siraitia grosvenorii has obvious anti-bacteria effect on the spoilage bacteria isolated from Sauced pork head meat and can be used as a new natural food preservation to prolong the shelf-life of Low-temperature meat products.

Effect of ingredients on oxidative stability of fish oil-enriched drinking yoghurt

DEFF Research Database (Denmark)

Nielsen, Nina Skall; Klein, Anna; Jacobsen, Charlotte

2009-01-01

, pectin, citric acid or gluconodelta- lactone did not affect the oxidative stability of fish oil-enriched yoghurt emulsions. Furthermore, the fruit preparation and added sugar did not lead to increased antioxidative activity. It is concluded that yoghurt as the dairy component in the fish oil......The oxidative stabilities of fish oil-enriched milk and fish oil-enriched drinking yoghurt were compared by following the development of lipid oxidation in plain milk, plain yoghurt and yoghurt to which ingredients present in drinking yoghurt were added one by one. All samples were enriched with 1...... wt-% fish oil. After 3 weeks of storage, development of peroxide values, volatile secondary oxidation products and fishy offflavors were much more pronounced in the milk compared to any of the yoghurt samples, irrespective of any added ingredients used to prepare flavored drinking yoghurt. Thus...

Combustión de mezclas ricas de etano-aire en medios porosos inertes Combustion of rich ethane-air mixtures in inert porous media

Directory of Open Access Journals (Sweden)

Khriscia Utria S

2013-04-01

Full Text Available El presente trabajo tiene por objetivo analizar teórica-experimentalmente la combustión de mezclas ricas de etano-aire en medios porosos inertes (MPI para evaluar la producción de hidrógeno y gas de síntesis. Se analizan los perfiles de temperatura, las velocidades de propagación de llama y los productos principales de la combustión, como son el hidrógeno (H2 y el monóxido de carbono (CO, mediante el uso de cromatografía gaseosa, para relaciones de equivalencia en el rango de 1,0 a 2,5 y dos diámetros de esferas de alúmina que componen el medio poroso. Se simula numéricamente el proceso de combustión mediante el uso del programa PREMIX utilizando dos mecanismos de reacción, como son el GRI-MECH 1.2 y GRI-MECH 3.0. Con GRI-MECH 3.0 se obtienen resultados numéricos que predicen correctamente los resultados experimentales para todo el rango de relaciones de equivalencia con un medio poroso compuesto por esferas de alúmina de 3,5 mm. La máxima generación de hidrógeno H2 y CO presentes en los productos de combustión son de 14,3% y 18,0%, respectivamente. El porcentaje de conversión de etano en H2 (61,3% y en CO (81% muestra el potencial de este combustible como generador de gas de síntesis.This research develops the theoretical and experimental analysis of ethane-air combustion in inert porous media (IPM to evaluate hydrogen and syngas production. Temperature profiles, flame propagation rates and major combustion products such as hydrogen (H2 and carbon monoxide (CO, through gas chromatography, are analysed at a range of equivalence ratios between 1.0 and 2.5, with two different alumina sphere diameters composing the porous media. Combustion of ethane-air mixture in IPM is simulated numerically using the PREMIX program with two reaction mechanisms, such as GRI-MECH 1.2 and GRI-MECH 3.0. GRI-MECH 3.0 numerical results predict correctly experimental results for a porous media with 3.5 mm alumina spheres along the range of

Effect of Ingredients on the Quality of Gluten-Free Sorghum Pasta.

Science.gov (United States)

Palavecino, Pablo Martín; Bustos, Mariela Cecilia; Heinzmann Alabí, María Belén; Nicolazzi, Melani Solange; Penci, María Cecilia; Ribotta, Pablo Daniel

2017-09-01

Sorghum is an underutilized cereal in human food production, despite its flour being a potential gluten-free (GF) source in the development of several foods. Thus, the aim of the present investigation was to evaluate the effects and interactions of different ingredients on cooking quality and texture of GF pasta. Egg albumen (A), egg powder (E), xanthan gum (X), and pregelatinized corn starch (P) were used as ingredients, and Box-Behnken experimental design was applied to study the effects of these ingredients on pasta cooking behavior, color, and texture attributes. Responses were fitted to a second order polynomial equation, and multivariable optimization was performed using maximization of general desirability. Next, optimal formulations were validated, compared with two commercial gluten-free pastas by sensory evaluation, and finally, an industrial assay was carried out. Regression coefficients indicated that A and P improved cooking properties while A and E contributed the most to improving the pasta textural properties. As, X and P effects varied depending on the kind of sorghum flour used, the optimal formulations levels were different, but in both cases these models were satisfactory and capable of predicting responses. The industrial assay was carried out with white sorghum flour because it showed a higher acceptability in the sensory evaluation than brown sorghum flour pasta. This industrially made pasta resulted in slightly better cooking properties than the laboratory produced one, with the formulation adapting well to the conventional wheat pasta industrial process. Gluten-free sorghum pasta was produced, showing good cooking and textural properties and being a suitable option for gluten-sensitive individuals. © 2017 Institute of Food Technologists®.

Tobacco companies' efforts to undermine ingredient disclosure: the Massachusetts benchmark study.

Science.gov (United States)

Velicer, Clayton; Aguinaga-Bialous, Stella; Glantz, Stanton

2016-09-01

To assess the 'Massachusetts Benchmark Study' (MBS) that the tobacco companies presented to the Massachusetts Department of Public Health (MDPH) in 1999 in response to ingredient disclosure regulations in the state. This case study can inform future ingredient disclosure regulations, including implementation of Articles 9 and 10 of the WHO Framework Convention on Tobacco Control (FCTC). We analysed documents available at http://legacy.library.ucsf.edu to identify internal communications regarding the design and execution of the MBS and internal studies on the relationship between tar, nicotine and carbon monoxide and smoke constituents and reviewed publications that further evaluated data published as part of the MBS. The companies conducted extensive studies of cigarette design factors and ingredients that significantly impacted the levels of constituents. While this study asserted that by-brand emissions could be estimated reliably from published tar, nicotine, and carbon monoxide levels, the tobacco companies were well aware that factors beyond tar, nicotine and carbon monoxide influenced levels of constituents included in the study. This severely limited the potential usefulness of the MBS predictor equations. Despite promises to provide data that would allow regulators to predict constituent data for all brands on the market, the final MBS results offered no useful predictive information to inform regulators, the scientific community or consumers. When implementing FCTC Articles 9 and 10, regulatory agencies should demand detailed by-brand information on tobacco product constituents and toxin deliveries to users. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

CHEMICAL-THERMAL PROCESSING OF TRACTOR PARTS IN VACUUM AT APPLICATION OF TECHNOLOGY OF HARDENING IN THE MEDIUM OF INERT GASES

Directory of Open Access Journals (Sweden)

статья Редакционная

2011-01-01

Full Text Available Advantages of technology of hardening by inert gases are considered. It is shown that use of unit ModulTherm7/1 at RUP «MTZ» allows to improve quality of chemical thermal processing of details and to provide decrease of expenses for manufacture.

Medium optimization for nuclease P1 production by Penicillium citrinum in solid-state fermentation using polyurethane foam as inert carrier

NARCIS (Netherlands)

Zhu, Y.; Knol, W.; Smits, J.P.; Bol, J.

1996-01-01

A solid-state fermentation system, using polyurethane foam as an inert carrier, was used for the production of nuclease P1 by Penicillium citrinum. Optimization of nuclease P1 production was carried out using a synthetic liquid medium. After a two-step medium optimization using a fractional

Dimeric Surfactants: Promising Ingredients of Cosmetics and Toiletries

Directory of Open Access Journals (Sweden)

Naveen Kumar

2013-11-01

Full Text Available Surfactants are an essential ingredient for cosmetic, toiletries and personal care products for enhancing their performance. Dimeric surfactants demonstrate superiority compared to conventional surfactants in all areas of application. Dimeric surfactants are extremely promising for utilization in various cosmetic formulations viz. shampoo, lotions, creams, conditioners etc. These surfactants possess extremely unique surface properties viz. lower surface tension, unique micellization, low critical micelle concentration (CMC and antimicrobial activity, higher solubilization etc. Dimerics enhance the performances of cosmetics in an extraordinary manner and provide eco-friendly preparations for human epidermis.

The smoke ion source: A device for the generation of cluster ions via inert gas condensation

International Nuclear Information System (INIS)

McHugh, K.M.; Sarkas, H.W.; Eaton, J.G.; Bowen, K.H.; Westgate, C.R.

1989-01-01

We report the development of an ion source for generating intense, continuous beams of both positive and negative cluster ions. This device is the result of the marriage of the inert gas condensation method with techniques for injecting electrons directly into expanding jets. In the preliminary studies described here, we have observed cluster ion size distributions ranging from n=1-400 for Pb n + and Pb n - and from n=12-5700 for Li n - . (orig.)

Sn and Cu oxide nanoparticles deposited on TiO{sub 2} nanoflower 3D substrates by Inert Gas Condensation technique

Energy Technology Data Exchange (ETDEWEB)

Kusior, A., E-mail: akusior@agh.edu.pl [Faculty of Materials Science and Ceramics, AGH University of Science and Technology, al. Mickiewicza 30, 30-059 Krakow (Poland); Kollbek, K. [Academic Centre for Materials and Nanotechnology, AGH University of Science and Technology, al. Mickiewicza 30, 30-059 Krakow (Poland); Kowalski, K. [Faculty of Metals Engineering and Industrial Computer Science, AGH University of Science and Technology, al. Mickiewicza 30, 30-059 Krakow (Poland); Borysiewicz, M. [Institute of Electron Technology, al. Lotnikow 32/46, 02-668 Warszawa (Poland); Wojciechowski, T. [Institute of Physics Polish Academy of Science, al. Lotnikow 32/46, 02-668 Warszawa (Poland); Adamczyk, A.; Trenczek-Zajac, A.; Radecka, M. [Faculty of Materials Science and Ceramics, AGH University of Science and Technology, al. Mickiewicza 30, 30-059 Krakow (Poland); Zakrzewska, K. [Faculty of Computer Science, Electronics and Telecommunications, AGH University of Science and Technology, al. Mickiewicza 30, 30-059 Krakow (Poland)

2016-09-01

Graphical abstract: - Highlights: • Inert Gas Condensation method yields non-agglomerated nanoparticles. • The growth of nanoparticles is controllable at the level of deposition. • Electrical conductivity increases with respect to pure nanostructured TiO{sub 2}. - Abstract: Sn and Cu oxide nanoparticles were deposited by Inert Gas Condensation (IGC) technique combined with dc magnetron sputtering onto nanoflower TiO{sub 2} 3D substrates obtained in the oxidation process of Ti-foil in 30% H{sub 2}O{sub 2}. Sputtering parameters such as insertion length and Ar/He flow rates were optimized taking into account the nanostructure morphology. Comparative studies with hydrothermal method were carried out. Surface properties of the synthesized nanomaterials were studied by Scanning Electron Microscopy, SEM, Atomic Force Microscopy, AFM, and X-ray Photoelectron Spectroscopy, XPS. X-ray diffraction, XRD and Raman spectroscopy were performed in order to determine phase composition. Impedance spectroscopy demonstrated the influence of nanoparticles on the electrical conductivity.

Gamma-ray astronomy from the ground and the space: first analyses of the HESS-II hybrid array and search for blazar candidates among the unidentified Fermi-LAT sources

International Nuclear Information System (INIS)

Lefaucheur, Julien

2015-01-01

This manuscript is about high energy gamma-ray astronomy (between 30 GeV and 300 GeV) with the Fermi-LAT satellite and very high energy gamma-ray astronomy (above ∼100 GeV) via the H.E.S.S. experiment. The second phase of the H.E.S.S. experiment began in July 2012 with the inauguration of a fifth 28 m-diameter telescope added to the initial array composed of four 12 m-diameter imaging atmospheric Cherenkov telescopes. In the first part of this thesis, we present the development of an analysis in hybrid mode based on a multivariate method dedicated to detect and study sources with different spectral shapes and the first analysis results on real data. The second part is dedicated to the research of blazar candidates among the Fermi-LAT unidentified sources of the 2FGL catalog. A first development is based on a multivariate approach using discriminant parameters built with the 2FGL catalog parameters. A second development is done with the use of the WISE satellite catalog and a non-parametric technic in order to find the blazar-like infrared counterparts of the unidentified sources of the 2FGL catalog. (author)

An integrated evidence-based targeting strategy for determining combinatorial bioactive ingredients of a compound herbal medicine Qishen Yiqi dripping pills.

Science.gov (United States)

Zhang, Yiqian; Yu, Jiahui; Zhang, Wen; Wang, Yuewei; He, Yi; Zhou, Shuiping; Fan, Guanwei; Yang, Hua; Zhu, Yan; Li, Ping

2018-06-12

Qishen Yiqi is a widely used Chinese herbal medicine formula with "qi invigorating and blood activating" property. Its dripping pill preparation (QSYQ) is a commercial herbal medicine approved by the China Food and Drug Administration (CFDA) in 2003 and is extensively used clinically to treat cardiovascular diseases, such as ischemic heart failure and angina pectoris, as well as for the secondary prevention of myocardial infarction. However, the bioactive ingredients of QSYQ remain unclear. As QSYQ is a compound herbal formula, it is of great importance to elucidate its pharmacologically active ingredients and underlying synergetic effects. This experimental study was conducted to comprehensively determine the combinatorial bioactive ingredients (CBIs) in QSYQ and to elucidate their potential synergetic effects. The established strategy may shed new light on how to rapidly determine CBIs in complex herbal formulas with holistic properties. An integrated evidence-based targeting strategy was introduced and validated to determine CBIs in QSYQ. The strategy included the following steps: (1) Chemical ingredients in QSYQ were analyzed via UPLC-Q-TOF/MS in the negative and positive modes and were identified by comparison with standard compounds and previously reported data. Their potential therapeutic activities were predicted based on the ChEMBL database to preliminarily search for candidate bioactive ingredients, and their combination was defined as the CBIs. (2) The CBIs were directly trapped and prepared from QSYQ with a two-dimensional chromatographic separation system, and the remaining part was defined as the rest ingredients (RIs). (3) As animal and cell models, left anterior descending coronary artery ligation (LAD)-induced heart failure in rats and hypoxia-induced cardiac myocyte injury in H9c2 cells were applied to compare the potency of QSYQ, CBIs and RIs. (4) The synergetic effects on cardiac myocyte protection of multiple ingredients in CBIs were examined

Evidence of an Unidentified Extracellular Heat-Stable Factor Produced by Lysobacter enzymogenes (OH11) that Degrade Fusarium graminearum PH1 Hyphae.

Science.gov (United States)

Odhiambo, Benard Omondi; Xu, Gaoge; Qian, Guoliang; Liu, Fengquan

2017-04-01

Lysobacter enzymogenes OH11 produces heat-stable antifungal factor (HSAF) and lytic enzymes possessing antifungal activity. This study bio-prospected for other potential antifungal factors besides those above. The cells and extracellular metabolites of L. enzymogenes OH11 and the mutants ΔchiA, ΔchiB, ΔchiC, Δclp, Δpks, and ΔpilA were examined for antifungal activity against Fusarium graminearum PH1, the causal agent of Fusarium head blight (FHB). Results evidenced that OH11 produces an unidentified extracellular heat-stable degrading metabolite (HSDM) that exhibit degrading activity on F. graminearum PH1 chitinous hyphae. Interestingly, both heat-treated and non-heat-treated extracellular metabolites of OH11 mutants exhibited hyphae-degrading activity against F. graminearum PH1. Enzyme activity detection of heat-treated metabolites ruled out the possibility of enzyme degradation activity. Remarkably, the PKS-NRPS-deficient mutant Δpks cannot produce HSAF or analogues, yet its metabolites exhibited hyphae-degrading activity. HPLC analysis confirmed no HSAF production by Δpks. Δclp lacks hyphae-degrading ability. Therefore, clp regulates HSDM and extracellular lytic enzymes production in L. enzymogenes OH11. ΔpilA had impaired surface cell motility and significantly reduced antagonistic properties. ΔchiA, ΔchiB, and ΔchiC retained hyphae-degrading ability, despite having reduced abilities to produce chitinase enzymes. Ultimately, L. enzymogenes OH11 can produce other unidentified HSDM independent of the PKS-NRPS genes. This suggests HSAF and lytic enzymes production are a fraction of the antifungal mechanisms in OH11. Characterization of HSDM, determination of its biosynthetic gene cluster and understanding its mode of action will provide new leads in the search for effective drugs for FHB management.