WorldWideScience

Sample records for underwater ambient noise

  1. The Impact of Offshore Wind Turbines on Underwater Ambient Noise Levels

    OpenAIRE

    Glegg, Stewart

    2015-01-01

    The underwater sound levels generated by offshore wind turbine farms is a concern because of the possible environmental impact on marine mammals. This paper will consider how sound generated by a wind turbine is transmitted into a shallow water channel. It is shown that the underwater sound levels can be calculated for a typical offshore wind turbine by using the theory of Chapman and Ward (1990) combined with aeroacoustic models of trailing edge noise on the wind turbine blades. A procedure ...

  2. Underwater Ambient Noise in a Baleen Whale Migratory Habitat Off the Azores

    Directory of Open Access Journals (Sweden)

    Miriam Romagosa

    2017-04-01

    Full Text Available Assessment of underwater noise is of particular interest given the increase in noise-generating human activities and the potential negative effects on marine mammals which depend on sound for many vital processes. The Azores archipelago is an important migratory and feeding habitat for blue (Balaenoptera musculus, fin (Balaenoptera physalus and sei whales (Balaenoptera borealis en route to summering grounds in northern Atlantic waters. High levels of low frequency noise in this area could displace whales or interfere with foraging behavior, impacting energy intake during a critical stage of their annual cycle. In this study, bottom-mounted Ecological Acoustic Recorders were deployed at three Azorean seamounts (Condor, Açores, and Gigante to measure temporal variations in background noise levels and ship noise in the 18–1,000 Hz frequency band, used by baleen whales to emit and receive sounds. Monthly average noise levels ranged from 90.3 dB re 1 μPa (Açores seamount to 103.1 dB re 1 μPa (Condor seamount and local ship noise was present up to 13% of the recording time in Condor. At this location, average contribution of local boat noise to background noise levels is almost 10 dB higher than wind contribution, which might temporally affect detection ranges for baleen whale calls and difficult communication at long ranges. Given the low time percentatge with noise levels above 120 dB re 1 μPa found here (3.3% at Condor, we woud expect limited behavioral responses to ships from baleen whales. Sound pressure levels measured in the Azores are lower than those reported for the Mediterranean basin and the Strait of Gibraltar. However, the currently unknown effects of baleen whale vocalization masking and the increasing presence of boats at the monitored sites underline the need for continuous monitoring to understand any long-term impacts on whales.

  3. Underwater Noise Modeling in Lithuanian Area of the Baltic Sea

    Directory of Open Access Journals (Sweden)

    Donatas Bagočius

    2017-09-01

    Full Text Available Along with rising awareness of public and scientific societies about environmental and ecological impacts of underwater noise, the need for underwater noise modelling in the shallow Lithuanian area of Baltic Sea emerged. Marine Strategy Framework Directive issues regarding underwater noise indicators refers to possibility of evaluation of Good Environmental State using underwater noise measurements as well as possibility to model underwater noise. Main anthropogenic underwater noise contributor in the Seas is the shipping lanes as known due to date, with no exclusion of Lithuanian Baltic Sea area. In this manuscript, it is presented the methods of development of simplistic underwater ambient noise model purposed for computation of underwater soundscape in shallow area of the Lithuanian Baltic Sea.

  4. Acoustic ambient noise recorder

    Digital Repository Service at National Institute of Oceanography (India)

    Saran, A.K.; Navelkar, G.S.; Almeida, A.M.; More, S.R.; Chodankar, P.V.; Murty, C.S.

    with a robust outfit that can withstand high pressures and chemically corrosion resistant materials. Keeping these considerations in view, a CMOS micro-controller-based marine acoustic ambient noise recorder has been developed with a real time clock...

  5. Underwater noise levels in UK waters

    OpenAIRE

    Merchant, Nathan D.; Brookes, Kate L.; Faulkner, Rebecca C.; Bicknell, Anthony W. J.; Godley, Brendan J.; Witt, Matthew J.

    2016-01-01

    Underwater noise from human activities appears to be rising, with ramifications for acoustically sensitive marine organisms and the functioning of marine ecosystems. Policymakers are beginning to address the risk of ecological impact, but are constrained by a lack of data on current and historic noise levels. Here, we present the first nationally coordinated effort to quantify underwater noise levels, in support of UK policy objectives under the EU Marine Strategy Framework Directive (MSFD). ...

  6. Underwater noise modelling for environmental impact assessment

    Energy Technology Data Exchange (ETDEWEB)

    Farcas, Adrian [Centre for Environment, Fisheries and Aquaculture Science (Cefas), Pakefield Road, Lowestoft, NR33 0HT (United Kingdom); Thompson, Paul M. [Lighthouse Field Station, Institute of Biological and Environmental Sciences, University of Aberdeen, Cromarty IV11 8YL (United Kingdom); Merchant, Nathan D., E-mail: nathan.merchant@cefas.co.uk [Centre for Environment, Fisheries and Aquaculture Science (Cefas), Pakefield Road, Lowestoft, NR33 0HT (United Kingdom)

    2016-02-15

    Assessment of underwater noise is increasingly required by regulators of development projects in marine and freshwater habitats, and noise pollution can be a constraining factor in the consenting process. Noise levels arising from the proposed activity are modelled and the potential impact on species of interest within the affected area is then evaluated. Although there is considerable uncertainty in the relationship between noise levels and impacts on aquatic species, the science underlying noise modelling is well understood. Nevertheless, many environmental impact assessments (EIAs) do not reflect best practice, and stakeholders and decision makers in the EIA process are often unfamiliar with the concepts and terminology that are integral to interpreting noise exposure predictions. In this paper, we review the process of underwater noise modelling and explore the factors affecting predictions of noise exposure. Finally, we illustrate the consequences of errors and uncertainties in noise modelling, and discuss future research needs to reduce uncertainty in noise assessments.

  7. Underwater noise generated by offshore pile driving

    NARCIS (Netherlands)

    Tsouvalas, A.

    2015-01-01

    Anthropogenic noise emission in the marine environment has always been an environmental issue of serious concern. In particular, the noise generated during the installation of foundation piles is considered to be one of the most significant sources of underwater noise pollution. This is mainly

  8. Underwater noise from offshore oil production vessels.

    Science.gov (United States)

    Erbe, Christine; McCauley, Robert; McPherson, Craig; Gavrilov, Alexander

    2013-06-01

    Underwater acoustic recordings of six Floating Production Storage and Offloading (FPSO) vessels moored off Western Australia are presented. Monopole source spectra were computed for use in environmental impact assessments of underwater noise. Given that operations on the FPSOs varied over the period of recording, and were sometimes unknown, the authors present a statistical approach to noise level estimation. No significant or consistent aspect dependence was found for the six FPSOs. Noise levels did not scale with FPSO size or power. The 5th, 50th (median), and 95th percentile source levels (broadband, 20 to 2500 Hz) were 188, 181, and 173 dB re 1 μPa @ 1 m, respectively.

  9. Impacts of underwater noise on marine vertebrates

    NARCIS (Netherlands)

    Liebschner, Alexander; Seibel, Henrike; Teilmann, Jonas; Wittekind, Dietrich; Parmentier, Eric; Dähne, Michael; Dietz, Rune; Driver, Jörg; Elk, van Cornelis; Everaarts, Eligius; Findeisen, Henning; Kristensen, Jacob; Lehnert, Kristina; Lucke, Klaus; Merck, Thomas; Müller, Sabine; Pawliczka, Iwona; Ronnenberg, Katrin; Rosenberger, Tanja; Ruser, Andreas; Tougaard, Jakob; Schuster, Max; Sundermeyer, Janne; Sveegaard, Signe; Siebert, Ursula

    2016-01-01

    The project conducts application-oriented research on impacts of underwater noise on marine vertebrates in the North and Baltic Seas. In distinct subprojects, the hearing sensitivity of harbor porpoises and gray seals as well as the acoustic tolerance limit of harbor porpoises to impulsive noise

  10. Underwater Noise Modelling of Wave Energy Devices

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-07-01

    Future large-scale implementation of wave energy converts (WECs) will introduce an anthropogenic activity in the ocean which may contribute to underwater noise. The Ocean houses several marine species with acoustic sensibility; consequently the potential impact of the underwater noise needs to be addressed. At present, there are no acoustic impact studies based on acquired data. The WEAM project (Wave Energy Acoustic Monitoring) aims at developing an underwater noise monitoring plan for WECs. The development of an acoustic monitoring plan must consider the sound propagation in the ocean, identify noise sources, understand the operational characteristics and select adequate instrumentation. Any monitoring strategy must involve in-situ measurements. However, the vast distances which sound travels within the ocean, can make in-situ measurements covering the entire area of interest, impracticable. This difficulty can be partially overcome through acoustic numerical modelling. This paper presents a synthetic study, on the application of acoustic forward modelling and the evaluation of the impact of noise produced by wave energy devices on marine mammals using criteria based on audiograms of dolphins, or other species. The idea is to illustrate the application of that methodology, and to show to what extent it allows for estimating distances of impacts due to acoustic noise.

  11. Underwater noise levels in UK waters.

    Science.gov (United States)

    Merchant, Nathan D; Brookes, Kate L; Faulkner, Rebecca C; Bicknell, Anthony W J; Godley, Brendan J; Witt, Matthew J

    2016-11-10

    Underwater noise from human activities appears to be rising, with ramifications for acoustically sensitive marine organisms and the functioning of marine ecosystems. Policymakers are beginning to address the risk of ecological impact, but are constrained by a lack of data on current and historic noise levels. Here, we present the first nationally coordinated effort to quantify underwater noise levels, in support of UK policy objectives under the EU Marine Strategy Framework Directive (MSFD). Field measurements were made during 2013-2014 at twelve sites around the UK. Median noise levels ranged from 81.5-95.5 dB re 1 μPa for one-third octave bands from 63-500 Hz. Noise exposure varied considerably, with little anthropogenic influence at the Celtic Sea site, to several North Sea sites with persistent vessel noise. Comparison of acoustic metrics found that the RMS level (conventionally used to represent the mean) was highly skewed by outliers, exceeding the 97 th percentile at some frequencies. We conclude that environmental indicators of anthropogenic noise should instead use percentiles, to ensure statistical robustness. Power analysis indicated that at least three decades of continuous monitoring would be required to detect trends of similar magnitude to historic rises in noise levels observed in the Northeast Pacific.

  12. Impact of Vessel Noise on Oyster Toadfish (Opsanus tau) Behavior and Implications for Underwater Noise Management

    Science.gov (United States)

    Krahforst, Cecilia S.

    Underwater noise and its impacts on marine life are growing management concerns. This dissertation considers both the ecological and social concerns of underwater noise, using the oyster toadfish (Opsanus tau) as a model species. Oyster toadfish call for mates using a boatwhistle sound, but increased ambient noise levels from vessels or other anthropogenic activities are likely to influence the ability of males to find mates. If increased ambient noise levels reduce fish fitness then underwater noise can impact socially valued ecosystem services (e.g. fisheries). The following ecological objectives of the impacts of underwater noise on oyster toadfish were investigated: (1) to determine how noise influences male calling behavior; (2) to assess how areas of high vessel activity ("noisy") and low vessel activity ("quiet") influence habitat utilization (fish standard length and occupancy rate); and (3) to discover if fitness (number of clutches and number of embryos per clutch) is lower in "noisy" compared with "quiet" sites. Field experiments were executed in "noisy" and "quiet" areas. Recorded calls by males in response to playback sounds (vessel, predator, and snapping shrimp sounds) and egg deposition by females ("noisy" vs. "quiet" sites) demonstrated that oyster toadfish are impacted by underwater noise. First, males decreased their call rates and called louder in response to increased ambient noise levels. Second, oyster toadfish selected nesting sites in areas with little or no inboard motorboat activity. Third, male oyster toadfish at "noisy" sites either had no egg clutches on their shelters or the number of embryos per clutch was significantly lower than in the "quiet" areas. Underwater noise and disturbance from vessels are influencing the fitness of the oyster toadfish. The social significance of the growing concerns regarding underwater noise was investigated by identifying dominant themes found within two types of texts: four recent underwater noise

  13. Characterization of ships as sources of underwater noise

    NARCIS (Netherlands)

    Jong, C.A.F. de

    2009-01-01

    There is a growing interest in the possible impact of anthropogenic underwater noise on marine life [1]. One of the concerns is the increasing contribution of shipping noise, with the growing number and size of commercial ships. Traditionally, underwater radiated noise control was only of interest

  14. Underwater radiated noise from modern commercial ships.

    Science.gov (United States)

    McKenna, Megan F; Ross, Donald; Wiggins, Sean M; Hildebrand, John A

    2012-01-01

    Underwater radiated noise measurements for seven types of modern commercial ships during normal operating conditions are presented. Calibrated acoustic data (autonomous seafloor-mounted acoustic recorder were combined with ship passage information from the Automatic Identification System. This approach allowed for detailed measurements (i.e., source level, sound exposure level, and transmission range) on ships of opportunity. A key result was different acoustic levels and spectral shapes observed from different ship-types. A 54 kGT container ship had the highest broadband source level at 188 dB re 1 μPa@1m; a 26 kGT chemical tanker had the lowest at 177 dB re 1 μPa@1m. Bulk carriers had higher source levels near 100 Hz, while container ship and tanker noise was predominantly below 40 Hz. Simple models to predict source levels of modern merchant ships as a group from particular ship characteristics (e.g., length, gross tonnage, and speed) were not possible given individual ship-type differences. Furthermore, ship noise was observed to radiate asymmetrically. Stern aspect noise levels are 5 to 10 dB higher than bow aspect noise levels. Collectively, these results emphasize the importance of including modern ship-types in quantifying shipping noise for predictive models of global, regional, and local marine environments. © 2012 Acoustical Society of America.

  15. Underwater noise from a wave energy converter

    DEFF Research Database (Denmark)

    Tougaard, Jakob

    in full operation and start and stop of the converter. Median broad band (10 Hz – 20 kHz) sound pressure level (Leq) was 123 dB re. 1 Pa, irrespective of status of the wave energy converter (stopped, running or starting/stopping). The most pronounced peak in the third-octave spectrum was in the 160 Hz...... band during start and stop of the converter, attributed to the hydraulic pump responsible for lifting and lowering the absorbers. Less pronounced, but still statistically significant differences were seen in the bands 125, 160, 200 and 250 Hz when operation and ambient were compared. No statistically...... significant noise above ambient could be detected above the 250 Hz band. The absolute increase in noise above ambient was very small. L50 third-octave levels in the four bands with the converter running were thus only 1-2 dB above ambient L50 levels. The noise recorded 25 m from the wave energy converter...

  16. Characterization of ships as sources of underwater noise

    OpenAIRE

    Jong, C.A.F. de

    2009-01-01

    There is a growing interest in the possible impact of anthropogenic underwater noise on marine life [1]. One of the concerns is the increasing contribution of shipping noise, with the growing number and size of commercial ships. Traditionally, underwater radiated noise control was only of interest for naval [2,3] and fishery research vessels [4]. Due to the potential environmental impact, it becomes also relevant for commercial shipping. The challenge is to bring the expertise from the naval ...

  17. Evaluating underwater noise regulations for piling noise in Belgium and The Netherlands

    OpenAIRE

    Rumes, B.; Erkman, A.; Haelters, J.

    2016-01-01

    There is concern about possible effects on the marine ecosystem of high levels of underwater noise generated during pile driving for the construction of offshore wind farms. As a result, various national governments in Europe have identified limits of underwater sound levels, as such imposing in many cases the use of noise mitigation measures. In this paper we compare the regulations with regard to impulsive underwater noise in the Belgian wind farm zone with those in the Dutch wind energy zo...

  18. Underwater noise from a wave energy converter

    DEFF Research Database (Denmark)

    Tougaard, Jakob

    of the absorber type. During recordings the converter was operating close to maximum power output (nominal capacity of 110 kW). During operation the independently operating absorbers float semi-submerged in the water and wave-generated up-and-down motion is converted into hydraulic pressure by means of pistons...... connected to the arms of the absorbers. The hydraulic pressure then in turn drives the generator. A 57 minute sequence of noise from the converter was recorded by a Loggerhead datalogger deployed in 7 m deep water 25 m from the converter. This sequence contained recordings of ambient noise, the converter...... in full operation and start and stop of the converter. Median broad band (10 Hz – 20 kHz) sound pressure level (Leq) was 123 dB re. 1 Pa, irrespective of status of the wave energy converter (stopped, running or starting/stopping). The most pronounced peak in the third-octave spectrum was in the 160 Hz...

  19. Underwater Noise from a Wave Energy Converter Is Unlikely to Affect Marine Mammals

    OpenAIRE

    Tougaard, Jakob

    2015-01-01

    Underwater noise was recorded from the Wavestar wave energy converter; a full-scale hydraulic point absorber, placed on a jack-up rig on the Danish North Sea coast. Noise was recorded 25 m from the converter with an autonomous recording unit (10 Hz to 20 kHz bandwidth). Median sound pressure levels (Leq) in third-octave bands during operation of the converter were 106-109 dB re. 1 μPa in the range 125-250 Hz, 1-2 dB above ambient noise levels (statistically significant). Outside the range 125...

  20. Ambient Noise Characteristics During the Sheba Experiment

    National Research Council Canada - National Science Library

    Shaw, Ronald

    2000-01-01

    The ambient noise data recorded by two free-drifting buoys during the 1997-98 SHEBA experiment presented a unique opportunity to gauge the noise field of the Arctic Ocean in a unique and changing environment...

  1. The effect of floating deck structures on underwater radiated noise

    NARCIS (Netherlands)

    Bosschaart, C.; Jansen, H.W.; Jong, C.A.F. de; Basten, T.

    2017-01-01

    A concept for underwater machinery noise mitigation of future civil and military ships is the application of a common deck structure, supporting multiple machines, which is installed on resilient mounts on the ship's foundation structure. TNO is addressing the availability and testing of tools to be

  2. Averaging underwater noise levels for environmental assessment of shipping

    OpenAIRE

    Merchant, Nathan D.; Blondel, Philippe; Dakin, D. Tom; Dorocicz, John

    2012-01-01

    Rising underwater noise levels from shipping have raised concerns regarding chronic impacts to marine fauna. However, there is a lack of consensus over how to average local shipping noise levels for environmental impact assessment. This paper addresses this issue using 110 days of continuous data recorded in the Strait of Georgia, Canada. Probability densities of ∼ 10 7 1-s samples in selected 1/3 octave bands were approximately stationary across one-month subsamples. Median and mode levels v...

  3. Investigation of solar noise impact on the performance of underwater wireless optical communication links.

    Science.gov (United States)

    Hamza, Tasnim; Khalighi, Mohammad-Ali; Bourennane, Salah; Léon, Pierre; Opderbecke, Jan

    2016-10-31

    We investigate the effect of environmental noise, caused by solar radiations under water, on the performance of underwater wireless optical communication (UWOC) systems. Presenting an analytical and generic model for this noise, we examine its impact on the link performance in terms of the bit error rate (BER). This study is conducted for different photo-detector types in the aim of highlighting practical limitations of establishing UWOC links in the presence of subsea solar noise. We show how the solar noise can impact the performance of UWOC links for relatively low operation depths. The results we present provide valuable insight for the design of UWOC links, which are likely to be established at relatively low depths. They can be exploited not only for the purpose of practical UWOC system deployment but also for in-pool experimental set-ups, since they elucidate the effect of ambient light on the measurements.

  4. Ocean Ambient Noise Measurement and Theory

    CERN Document Server

    Carey, William M

    2011-01-01

    This book develops the theory of ocean ambient noise mechanisms and measurements, and also describes general noise characteristics and computational methods.  It concisely summarizes the vast ambient noise literature using theory combined with key representative results.  The air-sea boundary interaction zone is described in terms of non-dimensional variables requisite for future experiments.  Noise field coherency, rare directional measurements, and unique basin scale computations and methods are presented.  The use of satellite measurements in these basin scale models is demonstrated.  Finally, this book provides a series of appendices giving in-depth mathematical treatments.  With its complete and careful discussions of both theory and experimental results, this book will be of the greatest interest to graduate students and active researchers working in fields related to ambient noise in the ocean.

  5. Potential Impacts of Ambient Noise in the on Marine Mammals

    National Research Council Canada - National Science Library

    Frisk, George

    2003-01-01

    The Committee was charged with assessing our state of knowledge of underwater noise and recommending research areas to assist in determining whether noise in the ocean adversely affects marine mammals...

  6. Averaging underwater noise levels for environmental assessment of shipping.

    Science.gov (United States)

    Merchant, Nathan D; Blondel, Philippe; Dakin, D Tom; Dorocicz, John

    2012-10-01

    Rising underwater noise levels from shipping have raised concerns regarding chronic impacts to marine fauna. However, there is a lack of consensus over how to average local shipping noise levels for environmental impact assessment. This paper addresses this issue using 110 days of continuous data recorded in the Strait of Georgia, Canada. Probability densities of ~10(7) 1-s samples in selected 1/3 octave bands were approximately stationary across one-month subsamples. Median and mode levels varied with averaging time. Mean sound pressure levels averaged in linear space, though susceptible to strong bias from outliers, are most relevant to cumulative impact assessment metrics.

  7. Underwater Noise Pollution at the Strait of Istanbul (Bosphorus

    Directory of Open Access Journals (Sweden)

    Cem Gazioğlu

    2016-12-01

    Full Text Available Underwater noise pollution (UNP has become a major concern in marine habitats, which is intense anthropogenic noise in the marine (aquatic environment. It is caused by ship traffic, oceanographic experiments, and use of explosives in geophysical research, underwater construction, active sonars and seismic survey techniques. Oceans are much nosier than 1960s. Narrow and shallow channel noisy aquatic environments where noise levels reach the highest value is not surprising. The Strait of Istanbul (SoI; Bosphorus is one of the most important maritime passages (app. 50 000 vessel/year or 140 vessel/day which is situated between the Black Sea and the Aegean Sea are also biologically extremely important gateway not only it provides access to a channel. Many of the varieties of fish migration hunting value are realized through the TSS. Local maritime traffic is another important acoustic sources which are more than 3 000 elements (Kesgin and Vardar, 2001 of everyday local traffic in SoI, which are causing noise in the 2 and 10 kHz range. Large vessels create signals both in bands below 1 kHz (main engine, electrical instruments cavitation noise creates higher frequency bands. Almost all elements of marine traffic in SoI located therefore encountered UND in all bands.

  8. Towards full waveform ambient noise inversion

    Science.gov (United States)

    Sager, Korbinian; Ermert, Laura; Boehm, Christian; Fichtner, Andreas

    2018-01-01

    In this work we investigate fundamentals of a method—referred to as full waveform ambient noise inversion—that improves the resolution of tomographic images by extracting waveform information from interstation correlation functions that cannot be used without knowing the distribution of noise sources. The fundamental idea is to drop the principle of Green function retrieval and to establish correlation functions as self-consistent observables in seismology. This involves the following steps: (1) We introduce an operator-based formulation of the forward problem of computing correlation functions. It is valid for arbitrary distributions of noise sources in both space and frequency, and for any type of medium, including 3-D elastic, heterogeneous and attenuating media. In addition, the formulation allows us to keep the derivations independent of time and frequency domain and it facilitates the application of adjoint techniques, which we use to derive efficient expressions to compute first and also second derivatives. The latter are essential for a resolution analysis that accounts for intra- and interparameter trade-offs. (2) In a forward modelling study we investigate the effect of noise sources and structure on different observables. Traveltimes are hardly affected by heterogeneous noise source distributions. On the other hand, the amplitude asymmetry of correlations is at least to first order insensitive to unmodelled Earth structure. Energy and waveform differences are sensitive to both structure and the distribution of noise sources. (3) We design and implement an appropriate inversion scheme, where the extraction of waveform information is successively increased. We demonstrate that full waveform ambient noise inversion has the potential to go beyond ambient noise tomography based on Green function retrieval and to refine noise source location, which is essential for a better understanding of noise generation. Inherent trade-offs between source and structure

  9. An intelligent subsurface buoy design for measuring ocean ambient noise

    Science.gov (United States)

    Li, Bing; Wang, Lei

    2012-11-01

    A type of ultra-low power subsurface buoy system is designed to measure and record ocean ambient noise data. The buoy utilizes a vector hydrophone (pass band 20Hz-1.2kHz) and a 6-element vertical hydrophone array (pass band 20Hz-2kHz) to measure ocean ambient noise. The acoustic signals are passed through an automatically modified gain, a band pass filter, and an analog-to-digital (A/D) conversion module. They are then stored in high-capacity flash memory. In order to identify the direction of noise source, the vector sensor measuring system has integrated an electric-magnetic compass. The system provides a low-rate underwater acoustic communication system which is used to report the buoy state information and a high-speed USB interface which is used to retrieve the recorded data on deck. The whole system weighs about 125kg and can operate autonomously for more than 72 hours. The system's main architecture and the sea-trial test results are provided in this paper.

  10. Ambient Noise in an Urbanized Tidal Channel

    Science.gov (United States)

    Bassett, Christopher

    In coastal environments, when topographic and bathymetric constrictions are combined with large tidal amplitudes, strong currents (> 2 m/s) can occur. Because such environments are relatively rare and difficult to study, until recently, they have received little attention from the scientific community. However, in recent years, interest in developing tidal hydrokinetic power projects in these environments has motivated studies to improve this understanding. In order to support an analysis of the acoustic effects of tidal power generation, a multi-year study was conducted at a proposed project site in Puget Sound (WA) are analyzed at a site where peak currents exceeded 3.5 m/s. From these analyses, three noise sources are shown to dominate the observed variability in ambient noise between 0.02-30 kHz: anthropogenic noise from vessel traffic, sediment-generated noise during periods of strong currents, and flow-noise resulting from turbulence advected over the hydrophones. To assess the contribution of vessel traffic noise, one calendar year of Automatic Identification System (AIS) ship-traffic data was paired with hydrophone recordings. The study region included inland waters of the Salish Sea within a 20 km radius of the hydrophone deployment site in northern Admiralty Inlet. The variability in spectra and hourly, daily, and monthly ambient noise statistics for unweighted broadband and M-weighted sound pressure levels is driven largely by vessel traffic. Within the one-year study period, at least one AIS transmitting vessel is present in the study area 90% of the time and over 1,363 unique vessels are recorded. A noise budget for vessels equipped with AIS transponders identifies cargo ships, tugs, and passenger vessels as the largest contributors to noise levels. A simple model to predict received levels at the site based on an incoherent summation of noise from different vessel types yields a cumulative probability density function of broadband sound pressure

  11. Underwater noise of small personal watercraft (jet skis).

    Science.gov (United States)

    Erbe, Christine

    2013-04-01

    Personal watercraft (water scooters, jet skis) were recorded under water in Bramble Bay, Queensland, Australia. Underwater noise emissions consisted of broadband energy between 100 Hz and 10 kHz due to the vibrating bubble cloud generated by the jet stream, overlain with frequency-modulated tonals corresponding to impeller blade rates and harmonics. Broadband monopole source levels were 149, 137, and 122 dB re 1 μPa @ 1 m (5th, 50th, and 95th percentiles). Even though these are lower than those of small propeller-driven boats, it is not necessarily the broadband source level that correlates with the bioacoustic impact on marine fauna.

  12. Underwater noise pollution in a coastal tropical environment.

    Science.gov (United States)

    Bittencourt, L; Carvalho, R R; Lailson-Brito, J; Azevedo, A F

    2014-06-15

    Underwater noise pollution has become a major concern in marine habitats. Guanabara Bay, southeastern Brazil, is an impacted area of economic importance with constant vessel traffic. One hundred acoustic recording sessions took place over ten locations. Sound sources operating within 1 km radius of each location were quantified during recordings. The highest mean sound pressure level near the surface was 111.56±9.0 dB re 1 μPa at the frequency band of 187 Hz. Above 15 kHz, the highest mean sound pressure level was 76.21±8.3 dB re 1 μPa at the frequency 15.89 kHz. Noise levels correlated with number of operating vessels and vessel traffic composition influenced noise profiles. Shipping locations had the highest noise levels, while small vessels locations had the lowest noise levels. Guanabara Bay showed noise pollution similar to that of other impacted coastal regions, which is related to shipping and vessel traffic. Copyright © 2014 Elsevier Ltd. All rights reserved.

  13. Underwater Noise from a Wave Energy Converter Is Unlikely to Affect Marine Mammals.

    Directory of Open Access Journals (Sweden)

    Jakob Tougaard

    Full Text Available Underwater noise was recorded from the Wavestar wave energy converter; a full-scale hydraulic point absorber, placed on a jack-up rig on the Danish North Sea coast. Noise was recorded 25 m from the converter with an autonomous recording unit (10 Hz to 20 kHz bandwidth. Median sound pressure levels (Leq in third-octave bands during operation of the converter were 106-109 dB re. 1 μPa in the range 125-250 Hz, 1-2 dB above ambient noise levels (statistically significant. Outside the range 125-250 Hz the noise from the converter was undetectable above the ambient noise. During start and stop of the converter a more powerful tone at 150 Hz (sound pressure level (Leq 121-125 dB re 1 μPa was easily detectable. This tone likely originated from the hydraulic pump which was used to lower the absorbers into the water and lift them out of the water at shutdown. Noise levels from the operating wave converter were so low that they would barely be audible to marine mammals and the likelihood of negative impact from the noise appears minimal. A likely explanation for the low noise emissions is the construction of the converter where all moving parts, except for the absorbers themselves, are placed above water on a jack-up rig. The results may thus not be directly transferable to other wave converter designs but do demonstrate that it is possible to harness wave energy without noise pollution to the marine environment.

  14. Underwater Noise from a Wave Energy Converter Is Unlikely to Affect Marine Mammals.

    Science.gov (United States)

    Tougaard, Jakob

    2015-01-01

    Underwater noise was recorded from the Wavestar wave energy converter; a full-scale hydraulic point absorber, placed on a jack-up rig on the Danish North Sea coast. Noise was recorded 25 m from the converter with an autonomous recording unit (10 Hz to 20 kHz bandwidth). Median sound pressure levels (Leq) in third-octave bands during operation of the converter were 106-109 dB re. 1 μPa in the range 125-250 Hz, 1-2 dB above ambient noise levels (statistically significant). Outside the range 125-250 Hz the noise from the converter was undetectable above the ambient noise. During start and stop of the converter a more powerful tone at 150 Hz (sound pressure level (Leq) 121-125 dB re 1 μPa) was easily detectable. This tone likely originated from the hydraulic pump which was used to lower the absorbers into the water and lift them out of the water at shutdown. Noise levels from the operating wave converter were so low that they would barely be audible to marine mammals and the likelihood of negative impact from the noise appears minimal. A likely explanation for the low noise emissions is the construction of the converter where all moving parts, except for the absorbers themselves, are placed above water on a jack-up rig. The results may thus not be directly transferable to other wave converter designs but do demonstrate that it is possible to harness wave energy without noise pollution to the marine environment.

  15. Ambient noise analysis of deep ocean measurements

    Science.gov (United States)

    Gaul, Roy D.; Knobles, David P.; Wittenborn, A. F.

    2004-05-01

    In October 1975 a measurement exercise designated CHURCH OPAL was done in the northeast Pacific Ocean to assess undersea acoustic noise and propagation phenomena. In 2003 the 10 days of deep ocean multiple hydrophone recordings during CHURCH OPAL were recovered and digitized. This paper presents results previously reported but unavailable for general distribution. The earlier work is augmented with more complete and detailed analyses using modern analytical techniques. Particular attention is given to statistical characterization of ambient noise within and beneath the deep sound channel in relation to distant shipping and local wind speed. [Work supported by ONR.

  16. Underwater noise in an impacted environment can affect Guiana dolphin communication.

    Science.gov (United States)

    Bittencourt, Lis; Lima, Isabela M S; Andrade, Luciana G; Carvalho, Rafael R; Bisi, Tatiana L; Lailson-Brito, José; Azevedo, Alexandre F

    2017-01-30

    This study focused on whistles produced by Guiana dolphin under different noise conditions in Guanabara Bay, southeastern Brazil. Recording sessions were performed with a fully calibrated recording system. Whistles and underwater noise levels registered during two behavioral states were compared separately between two areas. Noise levels differed between the two areas across all frequencies. Whistle duration differed between areas and was negatively correlated with noise levels. Whistling rate was positively correlated with noise levels, showing that whistling rate was higher in noisier conditions. Results demonstrated that underwater noise influenced Guiana dolphin acoustic behavior. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. Radial anisotropy ambient noise tomography of volcanoes

    Science.gov (United States)

    Mordret, Aurélien; Rivet, Diane; Shapiro, Nikolai; Jaxybulatov, Kairly; Landès, Matthieu; Koulakov, Ivan; Sens-Schönfelder, Christoph

    2016-04-01

    The use of ambient seismic noise allows us to perform surface-wave tomography of targets which could hardly be imaged by other means. The frequencies involved (~ 0.5 - 20 s), somewhere in between active seismic and regular teleseismic frequency band, make possible the high resolution imaging of intermediate-size targets like volcanic edifices. Moreover, the joint inversion of Rayleigh and Love waves dispersion curves extracted from noise correlations allows us to invert for crustal radial anisotropy. We present here the two first studies of radial anisotropy on volcanoes by showing results from Lake Toba Caldera, a super-volcano in Indonesia, and from Piton de la Fournaise volcano, a hot-spot effusive volcano on the Réunion Island (Indian Ocean). We will see how radial anisotropy can be used to infer the main fabric within a magmatic system and, consequently, its dominant type of intrusion.

  18. Calibration and Characterization of Autonomous Recorders Used in the Measurement of Underwater Noise.

    Science.gov (United States)

    Hayman, Gary; Robinson, Stephen; Lepper, Paul

    2016-01-01

    The use of autonomous recorders is motivated by the need to monitor underwater noise, such as in response to the requirements of the European Union Marine Strategy Framework Directive. The performance of these systems is a crucial factor governing the quality of the measured data, providing traceability for future underwater noise-monitoring programs aimed at the protection of the marine environment from anthropogenic noise. In this paper, a discussion is presented of measurement methodologies for the key acoustic performance characteristics of the recorders, including self-noise, dynamic range, and the absolute sensitivity as a function of frequency of the hydrophone and recorder system.

  19. Utgrunden off-shore wind farm - Measurements of underwater noise

    International Nuclear Information System (INIS)

    Lindell, Hans

    2003-07-01

    Airicole, GE Wind Energy and SEAS/Energi E2 have initiated this project in order to achieve a better understanding on how offshore based wind farms effect the underwater noise. The main reason is to gain knowledge on how marine wildlife could be effected by this kind of installation. The measurements were performed at Utgrunden wind farm that is situated at the reef Utgrunden on the Swedish southeast coast. The farm consists of seven 1,5 MW turbines. Three hydrophones registered the underwater sound and four accelerometers the tower vibrations. The measurement campaign was conducted during a period from November 2002 to February 2003. The objectives with this project is to answer the following issues and its results are: 1. What is the character of sound from a single power station? - The turbines radiate sound mainly at a few dominating frequencies from 30 Hz up to 800 Hz. At frequencies below 3 Hz no contribution from the turbines can be detected due to the high background level from the waves and the low tower vibration level. 2. What are the sound generating mechanisms in the turbine? - Gearbox mesh frequency vibrations that are transmitted via the tower structure and radiated out to the water mainly generate the sound. Airborne blade sound is effectively dampened in the transition from air to water. 3. How does the sound attenuate with increasing distance at different frequencies? - The average attenuation per doubled distance for frequencies between 31 Hz and 722 Hz is approximately 4 dB in the measured positions. No clear frequency dependence could be found. 4. How does the sound pressure level vary with increasing wind speed? - With increasing wind speed, the sound pressure level increases and the dominating frequencies move upward due to increasing turbine rotational speed. 5. How does sound from different power stations interfere with each other and influence the over all sound image? - No clear tendencies of interference could be observed in this study

  20. Underwater Noise Modeling and Direction-Finding Based on Heteroscedastic Time Series

    Directory of Open Access Journals (Sweden)

    Kamarei Mahmoud

    2007-01-01

    Full Text Available We propose a new method for practical non-Gaussian and nonstationary underwater noise modeling. This model is very useful for passive sonar in shallow waters. In this application, measurement of additive noise in natural environment and exhibits shows that noise can sometimes be significantly non-Gaussian and a time-varying feature especially in the variance. Therefore, signal processing algorithms such as direction-finding that is optimized for Gaussian noise may degrade significantly in this environment. Generalized autoregressive conditional heteroscedasticity (GARCH models are suitable for heavy tailed PDFs and time-varying variances of stochastic process. We use a more realistic GARCH-based noise model in the maximum-likelihood approach for the estimation of direction-of-arrivals (DOAs of impinging sources onto a linear array, and demonstrate using measured noise that this approach is feasible for the additive noise and direction finding in an underwater environment.

  1. Measurement and analysis of self-noise in hybrid-driven underwater gliders

    Directory of Open Access Journals (Sweden)

    LIU Lu

    2017-08-01

    Full Text Available The Hybrid-driven Underwater Glider (HUG is a new type of submersible vehicle which combines the functions of traditional Autonomous Underwater Vehicles(AUVand Autonomous Underwater Gliders(AUG. In order to study its noise source distribution and basic self-noise characteristics, a self-noise acquisition system based on the HUG was designed and developed, and a noise analysis test carried out in a free-field pool. In August 2016, the sea trial of the Petrel II glider was conducted in the South China Sea, with observation data at a depth range of 1 000 m as the research object. The self-noise data of the glider platform under different working conditions was obtained through the step-by-step operation method. The experimental analysis and results show that the self-noise acquisition system is stable. The contribution of mechanical noise to self-noise is greatest when the glider works in the gliding mode, while the self-noise band above 500 Hz is closely related to the work of the buoyancy adjustment unit, and peaks at 1 kHz. According to the analysis of the basic characteristics of self-noise, this provides some guidance for the implementation of vibration and noise reduction.

  2. Modelling techniques for underwater noise generated by tidal turbines in shallow water

    OpenAIRE

    Lloyd, Thomas P.; Turnock, Stephen R.; Humphrey, Victor F.

    2011-01-01

    The modelling of underwater noise sources and their potential impact on the marine environment is considered, focusing on tidal turbines in shallow water. The requirement for device noise prediction as part of environmental impact assessment is outlined and the limited amount of measurement data and modelling research identified. Following the identification of potential noise sources, the dominant flowgenerated sources are modelled using empirical techniques. The predicted sound pressure lev...

  3. Investigation of solar noise impact on the performance of underwater wireless optical communication links

    OpenAIRE

    Hamza, Tasnim; Khalighi, Mohammad-ali; Bourennane, Salah; Leon, Pierre; Opderbecke, Jan

    2016-01-01

    We investigate the effect of environmental noise, caused by solar radiations under water, on the performance of underwater wireless optical communication (UWOC) systems. Presenting an analytical and generic model for this noise, we examine its impact on the link performance in terms of the bit error rate (BER). This study is conducted for different photo-detector types in the aim of highlighting practical limitations of establishing UWOC links in the presence of subsea solar noise. We show ho...

  4. Underwater noise from three types of offshore wind turbines: estimation of impact zones for harbor porpoises and harbor seals.

    Science.gov (United States)

    Tougaard, Jakob; Henriksen, Oluf Damsgaard; Miller, Lee A

    2009-06-01

    Underwater noise was recorded from three different types of wind turbines in Denmark and Sweden (Middelgrunden, Vindeby, and Bockstigen-Valar) during normal operation. Wind turbine noise was only measurable above ambient noise at frequencies below 500 Hz. Total sound pressure level was in the range 109-127 dB re 1 microPa rms, measured at distances between 14 and 20 m from the foundations. The 1/3-octave noise levels were compared with audiograms of harbor seals and harbor porpoises. Maximum 1/3-octave levels were in the range 106-126 dB re 1 microPa rms. Maximum range of audibility was estimated under two extreme assumptions on transmission loss (3 and 9 dB per doubling of distance, respectively). Audibility was low for harbor porpoises extending 20-70 m from the foundation, whereas audibility for harbor seals ranged from less than 100 m to several kilometers. Behavioral reactions of porpoises to the noise appear unlikely except if they are very close to the foundations. However, behavioral reactions from seals cannot be excluded up to distances of a few hundred meters. It is unlikely that the noise reaches dangerous levels at any distance from the turbines and the noise is considered incapable of masking acoustic communication by seals and porpoises.

  5. An OFDM Receiver with Frequency Domain Diversity Combined Impulsive Noise Canceller for Underwater Network.

    Science.gov (United States)

    Saotome, Rie; Hai, Tran Minh; Matsuda, Yasuto; Suzuki, Taisaku; Wada, Tomohisa

    2015-01-01

    In order to explore marine natural resources using remote robotic sensor or to enable rapid information exchange between ROV (remotely operated vehicles), AUV (autonomous underwater vehicle), divers, and ships, ultrasonic underwater communication systems are used. However, if the communication system is applied to rich living creature marine environment such as shallow sea, it suffers from generated Impulsive Noise so-called Shrimp Noise, which is randomly generated in time domain and seriously degrades communication performance in underwater acoustic network. With the purpose of supporting high performance underwater communication, a robust digital communication method for Impulsive Noise environments is necessary. In this paper, we propose OFDM ultrasonic communication system with diversity receiver. The main feature of the receiver is a newly proposed Frequency Domain Diversity Combined Impulsive Noise Canceller. The OFDM receiver utilizes 20-28 KHz ultrasonic channel and subcarrier spacing of 46.875 Hz (MODE3) and 93.750 Hz (MODE2) OFDM modulations. In addition, the paper shows Impulsive Noise distribution data measured at a fishing port in Okinawa and at a barge in Shizuoka prefectures and then proposed diversity OFDM transceivers architecture and experimental results are described. By the proposed Impulsive Noise Canceller, frame bit error rate has been decreased by 20-30%.

  6. An OFDM Receiver with Frequency Domain Diversity Combined Impulsive Noise Canceller for Underwater Network

    Directory of Open Access Journals (Sweden)

    Rie Saotome

    2015-01-01

    Full Text Available In order to explore marine natural resources using remote robotic sensor or to enable rapid information exchange between ROV (remotely operated vehicles, AUV (autonomous underwater vehicle, divers, and ships, ultrasonic underwater communication systems are used. However, if the communication system is applied to rich living creature marine environment such as shallow sea, it suffers from generated Impulsive Noise so-called Shrimp Noise, which is randomly generated in time domain and seriously degrades communication performance in underwater acoustic network. With the purpose of supporting high performance underwater communication, a robust digital communication method for Impulsive Noise environments is necessary. In this paper, we propose OFDM ultrasonic communication system with diversity receiver. The main feature of the receiver is a newly proposed Frequency Domain Diversity Combined Impulsive Noise Canceller. The OFDM receiver utilizes 20–28 KHz ultrasonic channel and subcarrier spacing of 46.875 Hz (MODE3 and 93.750 Hz (MODE2 OFDM modulations. In addition, the paper shows Impulsive Noise distribution data measured at a fishing port in Okinawa and at a barge in Shizuoka prefectures and then proposed diversity OFDM transceivers architecture and experimental results are described. By the proposed Impulsive Noise Canceller, frame bit error rate has been decreased by 20–30%.

  7. Ambient noise in large rivers (L).

    Science.gov (United States)

    Vračar, Miodrag S; Mijić, Miomir

    2011-10-01

    This paper presents the results of hydroacoustic noise research in three large European rivers: the Danube, the Sava, and the Tisa. Noise in these rivers was observed during a period of ten years, which includes all annual variation in hydrological and meteorological conditions (flow rate, speed of flow, wind speed, etc.). Noise spectra are characterized by wide maximums at frequencies between 20 and 30 Hz, and relatively constant slope toward higher frequencies. Spectral level of noise changes in time in relatively wide limits. At low frequencies, below 100 Hz, the dynamics of noise level is correlated with the dynamics of water flow and speed. At higher frequencies, noise spectra are mostly influenced by human activities on river and on riverbanks. The influence of wind on noise in rivers is complex due to the annual variation of river surface. The influence of wind is less pronounced than in oceans, seas, and lakes. © 2011 Acoustical Society of America

  8. Ambient noise levels and detection threshold in Norway.

    Science.gov (United States)

    Demuth, Andrea; Ottemöller, Lars; Keers, Henk

    2016-01-01

    Ambient seismic noise is caused by a number of sources in specific frequency bands. The quantification of ambient noise makes it possible to evaluate station and network performance. We evaluate noise levels in Norway from the 2013 data set of the Norwegian National Seismic Network as well as two temporary deployments. Apart from the station performance, we studied the geographical and temporal variations, and developed a local noise model for Norway. The microseism peaks related to the ocean are significant in Norway. We, therefore, investigated the relationship between oceanic weather conditions and noise levels. We find a correlation of low-frequency noise (0.125-0.25 Hz) with wave heights up to 900 km offshore. High (2-10 Hz) and intermediate (0.5-5 Hz) frequency noise correlates only up to 450 km offshore with wave heights. From a geographic perspective, stations in southern Norway show lower noise levels for low frequencies due to a larger distance to the dominant noise sources in the North Atlantic. Finally, we studied the influence of high-frequency noise levels on earthquake detectability and found that a noise level increase of 10 dB decreases the detectability by 0.5 magnitude units. This method provides a practical way to consider noise variations in detection maps.

  9. Behavioural Response Thresholds in New Zealand Crab Megalopae to Ambient Underwater Sound

    Science.gov (United States)

    Stanley, Jenni A.; Radford, Craig A.; Jeffs, Andrew G.

    2011-01-01

    A small number of studies have demonstrated that settlement stage decapod crustaceans are able to detect and exhibit swimming, settlement and metamorphosis responses to ambient underwater sound emanating from coastal reefs. However, the intensity of the acoustic cue required to initiate the settlement and metamorphosis response, and therefore the potential range over which this acoustic cue may operate, is not known. The current study determined the behavioural response thresholds of four species of New Zealand brachyuran crab megalopae by exposing them to different intensity levels of broadcast reef sound recorded from their preferred settlement habitat and from an unfavourable settlement habitat. Megalopae of the rocky-reef crab, Leptograpsus variegatus, exhibited the lowest behavioural response threshold (highest sensitivity), with a significant reduction in time to metamorphosis (TTM) when exposed to underwater reef sound with an intensity of 90 dB re 1 µPa and greater (100, 126 and 135 dB re 1 µPa). Megalopae of the mud crab, Austrohelice crassa, which settle in soft sediment habitats, exhibited no response to any of the underwater reef sound levels. All reef associated species exposed to sound levels from an unfavourable settlement habitat showed no significant change in TTM, even at intensities that were similar to their preferred reef sound for which reductions in TTM were observed. These results indicated that megalopae were able to discern and respond selectively to habitat-specific acoustic cues. The settlement and metamorphosis behavioural response thresholds to levels of underwater reef sound determined in the current study of four species of crabs, enables preliminary estimation of the spatial range at which an acoustic settlement cue may be operating, from 5 m to 40 km depending on the species. Overall, these results indicate that underwater sound is likely to play a major role in influencing the spatial patterns of settlement of coastal crab

  10. Global-scale Full Waveform Ambient Noise Inversion

    Science.gov (United States)

    Sager, K.; Ermert, L. A.; Boehm, C.; Krischer, L.; Afanasiev, M.; Fichtner, A.

    2017-12-01

    In earthquake tomography, modern tomographic methods exploit waveforms for the benefit of improved resolution. However, these techniques cannot be applied to noise correlation functions without knowing the distribution of noise sources. To overcome this limitation, we develop a method - referred to as full waveform ambient noise inversion - that is valid for arbitrary noise source distributions in both space and frequency, accounts for 3D heterogeneous and attenuating media and the full seismic wave propagation physics. The fundamental idea is to drop the principle of Green function retrieval, which is the basis for current noise tomographic studies, and to establish correlation functions as self-consistent observables in seismology. Based on a synthetic study in 2D, investigating the prerequisites for a joint inversion for noise sources and Earth structure, we extend the open-source waveform modelling and inversion package Salvus (http://salvus.io). It allows us to compute correlation functions in 3D media with heterogeneous noise sources at the surface and the corresponding sensitivity kernels for the distribution of noise sources and Earth structure. We present sensitivity kernels for different cross-correlation time lags and various noise source distributions, and study the effect of 3D heterogeneous Earth structure. For a validation of full waveform ambient noise inversion, we apply it to a global dataset focusing on the Earth's hum period band.

  11. Underwater and Dive Station Work-Site Noise Surveys

    National Research Council Canada - National Science Library

    Wolgemuth, Keith S; Cudahy, Edward A; Schwaller, Derek W

    2008-01-01

    Previous work performed by the Naval Submarine Medical Research Laboratory (NSMRL) had developed in-water permissible continuous noise exposure guidance Work performed by the Navy Experimental Diving Unit...

  12. Eastern Arctic ambient noise on a drifting vertical array.

    Science.gov (United States)

    Ozanich, Emma; Gerstoft, Peter; Worcester, Peter F; Dzieciuch, Matthew A; Thode, Aaron

    2017-10-01

    Ambient noise in the eastern Arctic was studied from April to September 2013 using a 22 element vertical hydrophone array as it drifted from near the North Pole (89° 23'N, 62° 35'W) to north of Fram Strait (83° 45'N, 4° 28'W). The hydrophones recorded for 108 min/day on six days per week with a sampling rate of 1953.125 Hz. After removal of data corrupted by non-acoustic transients, 19 days throughout the transit period were analyzed. Noise contributors identified include broadband and tonal ice noises, bowhead whale calling, seismic airgun surveys, and earthquake T phases. The bowhead whale or whales detected are believed to belong to the endangered Spitsbergen population, and were recorded when the array was as far north as 86° 24'N. Median power spectral estimates and empirical probability density functions along the array transit show a change in the ambient noise levels corresponding to seismic survey airgun occurrence and received level at low frequencies and transient ice noises at high frequencies. Median power for the same periods across the array shows that this change is consistent in depth. The median ambient noise for May 2013 was among the lowest of the sparse reported observations in the eastern Arctic but comparable to the more numerous observations of western Arctic noise levels.

  13. The persistent signature of tropical cyclones in ambient seismic noise

    Science.gov (United States)

    Gualtieri, Lucia; Camargo, Suzana J.; Pascale, Salvatore; Pons, Flavio M. E.; Ekström, Göran

    2018-02-01

    The spectrum of ambient seismic noise shows strong signals associated with tropical cyclones, yet a detailed understanding of these signals and the relationship between them and the storms is currently lacking. Through the analysis of more than a decade of seismic data recorded at several stations located in and adjacent to the northwest Pacific Ocean, here we show that there is a persistent and frequency-dependent signature of tropical cyclones in ambient seismic noise that depends on characteristics of the storm and on the detailed location of the station relative to the storm. An adaptive statistical model shows that the spectral amplitude of ambient seismic noise, and notably of the short-period secondary microseisms, has a strong relationship with tropical cyclone intensity and can be employed to extract information on the tropical cyclones.

  14. The persistent signature of tropical cyclones in ambient seismic noise

    KAUST Repository

    Gualtieri, Lucia

    2017-12-28

    The spectrum of ambient seismic noise shows strong signals associated with tropical cyclones, yet a detailed understanding of these signals and the relationship between them and the storms is currently lacking. Through the analysis of more than a decade of seismic data recorded at several stations located in and adjacent to the northwest Pacific Ocean, here we show that there is a persistent and frequency-dependent signature of tropical cyclones in ambient seismic noise that depends on characteristics of the storm and on the detailed location of the station relative to the storm. An adaptive statistical model shows that the spectral amplitude of ambient seismic noise, and notably of the short-period secondary microseisms, has a strong relationship with tropical cyclone intensity and can be employed to extract information on the tropical cyclones.

  15. Accurate Ambient Noise Assessment Using Smartphones

    Science.gov (United States)

    Zamora, Willian; Calafate, Carlos T.; Cano, Juan-Carlos; Manzoni, Pietro

    2017-01-01

    Nowadays, smartphones have become ubiquitous and one of the main communication resources for human beings. Their widespread adoption was due to the huge technological progress and to the development of multiple useful applications. Their characteristics have also experienced a substantial improvement as they now integrate multiple sensors able to convert the smartphone into a flexible and multi-purpose sensing unit. The combined use of multiple smartphones endowed with several types of sensors gives the possibility to monitor a certain area with fine spatial and temporal granularity, a procedure typically known as crowdsensing. In this paper, we propose using smartphones as environmental noise-sensing units. For this purpose, we focus our study on the sound capture and processing procedure, analyzing the impact of different noise calculation algorithms, as well as in determining their accuracy when compared to a professional noise measurement unit. We analyze different candidate algorithms using different types of smartphones, and we study the most adequate time period and sampling strategy to optimize the data-gathering process. In addition, we perform an experimental study comparing our approach with the results obtained using a professional device. Experimental results show that, if the smartphone application is well tuned, it is possible to measure noise levels with a accuracy degree comparable to professional devices for the entire dynamic range typically supported by microphones embedded in smartphones, i.e., 35–95 dB. PMID:28430126

  16. Accurate Ambient Noise Assessment Using Smartphones.

    Science.gov (United States)

    Zamora, Willian; Calafate, Carlos T; Cano, Juan-Carlos; Manzoni, Pietro

    2017-04-21

    Nowadays, smartphones have become ubiquitous and one of the main communication resources for human beings. Their widespread adoption was due to the huge technological progress and to the development of multiple useful applications. Their characteristics have also experienced a substantial improvement as they now integrate multiple sensors able to convert the smartphone into a flexible and multi-purpose sensing unit. The combined use of multiple smartphones endowed with several types of sensors gives the possibility to monitor a certain area with fine spatial and temporal granularity, a procedure typically known as crowdsensing. In this paper, we propose using smartphones as environmental noise-sensing units. For this purpose, we focus our study on the sound capture and processing procedure, analyzing the impact of different noise calculation algorithms, as well as in determining their accuracy when compared to a professional noise measurement unit. We analyze different candidate algorithms using different types of smartphones, and we study the most adequate time period and sampling strategy to optimize the data-gathering process. In addition, we perform an experimental study comparing our approach with the results obtained using a professional device. Experimental results show that, if the smartphone application is well tuned, it is possible to measure noise levels with a accuracy degree comparable to professional devices for the entire dynamic range typically supported by microphones embedded in smartphones, i.e., 35-95 dB.

  17. Snapping shrimp noise mitigation based on statistical detection in underwater acoustic orthogonal frequency division multiplexing systems

    Science.gov (United States)

    Kim, Hyeonsu; Seo, Jongpil; Ahn, Jongmin; Chung, Jaehak

    2017-07-01

    We propose a mitigation scheme for snapping shrimp noise when it corrupts an orthogonal frequency division multiplexing (OFDM) signal in underwater acoustic communication systems. The OFDM signal distorted by the snapping shrimp noise is filtered by a band-stop filter. The snapping shrimp noises in the filtered signal are detected by a detector with a constant false alarm rate whose threshold is derived theoretically from the statistics of the background noise. The detected signals are reconstructed by a simple reconstruction method. The proposed scheme has a higher detection capability and a lower mean square error of the channel estimation for simulated data and a lower bit error rate for practical ocean OFDM data collected in northern East China Sea than the conventional noise-mitigating methods.

  18. Aspect-dependent radiated noise analysis of an underway autonomous underwater vehicle.

    Science.gov (United States)

    Gebbie, John; Siderius, Martin; Allen, John S

    2012-11-01

    This paper presents an analysis of the acoustic emissions emitted by an underway REMUS-100 autonomous underwater vehicle (AUV) that were obtained near Honolulu Harbor, HI using a fixed, bottom-mounted horizontal line array (HLA). Spectral analysis, beamforming, and cross-correlation facilitate identification of independent sources of noise originating from the AUV. Fusion of navigational records from the AUV with acoustic data from the HLA allows for an aspect-dependent presentation of calculated source levels of the strongest propulsion tone.

  19. Ambient Seismic Noise Tomography of Southern Norway

    Science.gov (United States)

    Köhler, Andreas; Weidle, Christian; Maupin, Valerie

    2010-05-01

    The noise cross-correlation technique is especially useful in regions like southern Norway since local seismicity is rare and teleseismic records are not able to resolve the upper crust. Within the TopoScandiaDeep project, which aims to investigate the relation between surface topography and lithosphere-asthenosphere structure, we process seismic broadband data from the temporary MAGNUS network in Southern Norway. The receivers were recording 20 months of continuous data between September 2006 and June 2008. Additionally, permanent stations of the National Norwegian Seismic Network, NORSAR and GSN stations in the region are used. After usual preprocessing steps (filtering, prewhitening, temporal normalization), we compute 820 cross-correlation functions from 41 receivers for three month time windows. Evaluation of the azimuthal and temporal variation of signal to noise ratios and f-k analysis of NORSAR array data shows that the dominant propagation direction of seismic noise is south-west to north, corresponding well to the Norwegian coast line. During summer months, the signal to noise ratios decrease and the azimuthal distribution becomes smoother. Time-frequency analysis is applied to measure Rayleigh and Love wave group velocity dispersion curves between each station pair for each three-month correlation stack. The mean and variance of all dispersion curves is computed for each path. After rejection of low-quality data using a signal to noise ratio, minimum wavelength and velocity variance criterion, we obtain a large number of reliable velocity estimates (about 600) for periods between 2 and 15 seconds, which we invert for group velocity maps at respective periods. At all inverted periods, we find positive and negative velocity anomalies for Rayleigh and Love waves that correlate very well with local surface geology. While higher velocities (+5%) can be associated with the Caledonian nappes in the central part of southern Norway, the Oslo Graben is reflected

  20. Communicating the Issue of Underwater Noise Pollution: The Deaf as a Fish Project.

    Science.gov (United States)

    Sebastianutto, Linda; Stocker, Michael; Picciulin, Marta

    2016-01-01

    Aquatic noise pollution is largely ignored by the lay public. How experts communicate this issue is critical to move public opinion. In 2010, the Cassa di Risparmio di Gorizia (CaRiGO) bank sponsored the Deaf as a Fish project that included local underwater noise monitoring, a boat census, a pamphlet for nonexperts, and some seminars and public meetings. This project allowed us to raise interest in this issue. Using accurate and understandable language in a light-humored setting goes far toward cultivating trust from a public audience that can be intimidated or suspicious of complicated scientific messaging.

  1. Evidence of Non-extensivity in Earth's Ambient Noise

    Science.gov (United States)

    Koutalonis, Ioannis; Vallianatos, Filippos

    2017-12-01

    The study of ambient seismic noise is one of the important scientific and practical research challenges, due to its use in a number of geophysical applications. In this work, we describe Earth's ambient noise fluctuations in terms of non-extensive statistical physics. We found that Earth's ambient noise increments follow the q-Gaussian distribution. This indicates that Earth's ambient noise's fluctuations are not random and present long-term memory effects that could be described in terms of Tsallis entropy. Our results suggest that q values depend on the time length used and that the non-extensive parameter, q, converges to value q → 1 for short-time windows and a saturation value of q ≈ 1.33 for longer ones. The results are discussed from the point of view of superstatistics introduced by Beck [Contin Mech Thermodyn 16(3):293-304, 2004] and connects the q values with the system's degrees of freedom. Our work indicates that the converged (maximum) value is q = 1.33 and is related to 5 degrees of freedom.

  2. Qademah Fault Artificial Ambient Noise Test

    KAUST Repository

    Hanafy, Sherif M.

    2014-01-01

    This data set was collected on 7 Dec. 2014 by Sherif and Abdullah. The receiver layout is the same as that of the passive data test at the same location, which is described as follow: 288 receivers are used and arranged as follow - 12 lines, cross-line offset = 10 m - 24 receiver in each line, inline offset = 5 m - Additional 24 receivers are placed at line # 6, where the receiver interval is decreased to 2.5 m. Data Recording: We start recording at 10:10 am and stop recording at 11:25 am. Each record has total of 20 s, with time interval of 0.004 ms and around 2 s overlap between each two successive files. Source: We used a piece of wood attached to a pick-up truck to create the noise; we drove around the array of receivers in a rectangle-shape route during the recording time.

  3. Shear velocity of the Rotokawa geothermal field using ambient noise

    Science.gov (United States)

    Civilini, F.; Savage, M. K.; Townend, J.

    2014-12-01

    Ambient noise correlation is an increasingly popular seismological technique that uses the ambient seismic noise recorded at two stations to construct an empirical Green's function. Applications of this technique include determining shear velocity structure and attenuation. An advantage of ambient noise is that it does not rely on external sources of seismic energy such as local or teleseismic earthquakes. This method has been used in the geothermal industry to determine the depths at which magmatic processes occur, to distinguish between production and non-production areas, and to observe seismic velocity perturbations associated with fluid extraction. We will present a velocity model for the Rotokawa geothermal field near Taupo, New Zealand, produced from ambient noise cross correlations. Production at Rotokawa is based on the "Rotokawa A" combined cycle power station established in 1997 and the "Nga Awa Purua" triple flash power plant established in 2010. Rotokawa Joint Venture, a partnership between Mighty River Power and Tauhara North No. 2 Trust currently operates 174 MW of generation at Rotokawa. An array of short period seismometers was installed in 2008 and occupies an area of roughly 5 square kilometers around the site. Although both cultural and natural noise sources are recorded at the stations, the instrument separation distance provides a unique challenge for analyzing cross correlations produced by both signal types. The inter-station spacing is on the order of a few kilometers, so waves from cultural sources generally are not coherent from one station to the other, while the wavelength produced by natural noise is greater than the station separation. Velocity models produced from these two source types will be compared to known geological models of the site. Depending on the amount of data needed to adequately construct cross-correlations, a time-dependent model of velocity will be established and compared with geothermal production processes.

  4. Amplification and Attenuation across USArray using Ambient Noise Wavefront Tracking

    KAUST Repository

    Bowden, Daniel C.

    2017-11-15

    As seismic travel-time tomography continues to be refined using data from the vast USArray dataset, it is advantageous to also exploit the amplitude information carried by seismic waves. We use ambient noise cross correlation to make observations of surface-wave amplification and attenuation at shorter periods (8 – 32 seconds) than can be observed with only traditional teleseismic earthquake sources. We show that the wavefront tracking approach of [Lin et al., 2012a] can be successfully applied to ambient noise correlations, yielding results quite similar to those from earthquake observations at periods of overlap. This consistency indicates that the wavefront tracking approach is viable for use with ambient noise correlations, despite concerns of the inhomogeneous and unknown distribution of noise sources. The resulting amplification and attenuation maps correlate well with known tectonic and crustal structure; at the shortest periods, our amplification and attenuation maps correlate well with surface geology and known sedimentary basins, while our longest period amplitudes are controlled by crustal thickness and begin to probe upper mantle materials. These amplification and attenuation observations are sensitive to crustal materials in different ways than travel-time observations and may be used to better constrain temperature or density variations. We also value them as an independent means of describing the lateral variability of observed Rayleigh-wave amplitudes without the need for 3D tomographic inversions.

  5. Underwater Noise from a Wave Energy Converter is unlikely to Affect Marine Mammals

    DEFF Research Database (Denmark)

    Tougaard, Jakob

    2015-01-01

    (Leq) in third-octave bands during operation of the converter were 106–109 dB re. 1 μPa in the range 125–250 Hz, 1–2 dB above ambient noise levels (statistically significant). Outside the range 125–250 Hz the noise from the converter was undetectable above the ambient noise. During start and stop...... were so low that they would barely be audible to marine mammals and the likelihood of negative impact from the noise appears minimal. A likely explanation for the low noise emissions is the construction of the converter where all moving parts, except for the absorbers themselves, are placed above water...

  6. A high-resolution ambient seismic noise model for Europe

    Science.gov (United States)

    Kraft, Toni

    2014-05-01

    In the past several years, geological energy technologies receive growing attention and have been initiated in or close to urban areas. Some of these technologies involve injecting fluids into the subsurface (e.g., oil and gas development, waste disposal, and geothermal energy development) and have been found or suspected to cause small to moderate sized earthquakes. These earthquakes, which may have gone unnoticed in the past when they occurred in remote sparsely populated areas, are now posing a considerable risk for the public acceptance of these technologies in urban areas. The permanent termination of the EGS project in Basel, Switzerland after a number of induced ML~3 (minor) earthquakes in 2006 is one prominent example. It is therefore essential to the future development and success of these geological energy technologies to develop strategies for managing induced seismicity and keeping the size of induced earthquake at a level that is acceptable to all stakeholders. Most guidelines and recommendations on induced seismicity published since the 1970ies conclude that an indispensable component of such a strategy is the establishment of seismic monitoring in an early stage of a project. This is because an appropriate seismic monitoring is the only way to detect and locate induced microearthquakes with sufficient certainty to develop an understanding of the seismic and geomechanical response of the reservoir to the geotechnical operation. In addition, seismic monitoring lays the foundation for the establishment of advanced traffic light systems and is therefore an important confidence building measure towards the local population and authorities. Due to this development an increasing number of seismic monitoring networks are being installed in densely populated areas with strongly heterogeneous, and unfavorable ambient noise conditions. This poses a major challenge on the network design process, which aims to find the sensor geometry that optimizes the

  7. Measurement of Underwater Operational Noise Emitted by Wave and Tidal Stream Energy Devices.

    Science.gov (United States)

    Lepper, Paul A; Robinson, Stephen P

    2016-01-01

    The increasing international growth in the development of marine and freshwater wave and tidal energy harvesting systems has been followed by a growing requirement to understand any associated underwater impact. Radiated noise generated during operation is dependent on the device's physical properties, the sound-propagation environment, and the device's operational state. Physical properties may include size, distribution in the water column, and mechanics/hydrodynamics. The sound-propagation environment may be influenced by water depth, bathymetry, sediment type, and water column acoustic properties, and operational state may be influenced by tidal cycle and wave height among others This paper discusses some of the challenges for measurement of noise characteristics from these devices as well as a case study of the measurement of radiated noise from a full-scale wave energy converter.

  8. When ambient noise impairs parent-offspring communication.

    Science.gov (United States)

    Lucass, Carsten; Eens, Marcel; Müller, Wendt

    2016-05-01

    Ambient noise has increased in extent, duration and intensity with significant implications for species' lives. Birds especially, because they heavily rely on vocal communication, are highly sensitive towards noise pollution. Noise can impair the quality of a territory or hamper the transmission of vocal signals such as song. The latter has significant fitness consequences as it may erode partner preferences in the context of mate choice. Additional fitness costs may arise if noise masks communication between soliciting offspring and providing parents during the period of parental care. Here, we experimentally manipulated the acoustic environment of blue tit (Cyanistes caeruleus) families within their nest boxes with playbacks of previously recorded highway noise and investigated the consequences on parent-offspring communication. We hypothesized that noise interferes with the acoustic cues of parental arrival and vocal components of offspring begging. As such we expected an increase in the frequency of missed detections, when nestlings fail to respond to the returning parent, and a decrease in parental provisioning rates. Parents significantly reduced their rate of provisioning in noisy conditions compared to a control treatment. This reduction is likely to be the consequence of a parental misinterpretation of the offspring hunger level, as we found that nestlings fail to respond to the returning parent more frequently in the presence of noise. Noise also potentially masks vocal begging components, again contributing to parental underestimation of offspring requirements. Either way, it appears that noise impaired parent-offspring communication is likely to reduce reproductive success. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. Monitoring and imaging the atmosphere with infrasonic ambient noise correlations

    Science.gov (United States)

    Haney, Matthew; Evers, Laslo

    2010-05-01

    The existence of widespread infrasonic ambient noise (e.g., microbaroms) opens up the possibility of investigating atmospheric acoustic structure with new techniques designed for continuous stochastic signals. This is in contrast to classical approaches that use deterministic signals (e.g., explosions) with clear phase arrivals. Here, we review some recent advances in the monitoring and imaging of the atmosphere derived from analysis of continuous infrasound noise. From two microbarometers located at Fourpeaked Volcano in Alaska, we observe coherent arrivals in cross-correlations of ambient noise in the microbarom band (0.2-0.5 Hz) at time lags that agree well with speeds expected for a direct infrasound wave in the atmosphere (300-340 m/s). A striking example of the dependence of the ambient noise correlations on atmospheric conditions is evident from a comparison with temperature and wind data measured on nearby ocean buoys. Application of the multiple-filter technique reveals that the group velocity of the infrasound wave is dispersive, with higher group velocities at lower frequencies. This supports the existence of a low-level atmospheric waveguide at Fourpeaked Volcano during the time period under study. We invert the observed time-dependent group velocity dispersion curves for average sound speed profiles as a function of time. The inverted sound speed profiles show that a time-dependent, surface-based inversion layer became stronger over a period of 24 hours, with a colder, denser, and lower sound speed layer moving between the stations. This layer is imaged in the lower 2 km of the atmosphere and demonstrates the sensitivity of ambient noise correlations to the atmospheric boundary layer. Independent analysis of meteorological data in and around Fourpeaked volcano from the same time period supports the results derived from the infrasound ambient noise correlations. We also show examples of ambient noise correlations from time periods of normal temperature

  10. Three-component ambient noise beamforming in the Parkfield area

    Science.gov (United States)

    Löer, Katrin; Riahi, Nima; Saenger, Erik H.

    2018-02-01

    We apply a three-component beamforming algorithm to an ambient noise data set recorded at a seismic array to extract information about both isotropic and anisotropic surface wave velocities. In particular, we test the sensitivity of the method with respect to the array geometry as well as to seasonal variations in the distribution of noise sources. In the earth's crust, anisotropy is typically caused by oriented faults or fractures and can be altered when earthquakes or human activities cause these structures to change. Monitoring anisotropy changes thus provides time dependent information on subsurface processes, provided they can be distinguished from other effects. We analyse ambient noise data at frequencies between 0.08 {{Hz}} and 0.52 {{Hz}} recorded at a three-component array in the Parkfield area, California (US), between November 2001 and April 2002. During this time, no major earthquakes were identified in the area and structural changes are thus not expected. We compute dispersion curves of Love and Rayleigh waves and estimate anisotropy parameters for Love waves. For Rayleigh waves, the azimuthal source coverage is too limited to perform anisotropy analysis. For Love waves, ambient noise sources are more widely distributed and we observe significant and stable surface wave anisotropy for frequencies between 0.2 {{Hz}} and 0.4 {{Hz}}. Synthetic data experiments indicate that the array geometry introduces apparent anisotropy, especially when waves from multiple sources arrive simultaneously at the array. Both the magnitude and the pattern of apparent anisotropy, however, differ significantly from the anisotropy observed in Love wave data. Temporal variations of anisotropy parameters observed at frequencies below 0.2 {{Hz}} and above 0.4 {{Hz}} correlate with changes in the source distribution. Frequencies between 0.2 {{Hz}} and 0.4 {{Hz}}, however, are less affected by these variations and provide relatively stable results over the period of study.

  11. An adaptive grid to improve the efficiency and accuracy of modelling underwater noise from shipping

    Science.gov (United States)

    Trigg, Leah; Chen, Feng; Shapiro, Georgy; Ingram, Simon; Embling, Clare

    2017-04-01

    Underwater noise from shipping is becoming a significant concern and has been listed as a pollutant under Descriptor 11 of the Marine Strategy Framework Directive. Underwater noise models are an essential tool to assess and predict noise levels for regulatory procedures such as environmental impact assessments and ship noise monitoring. There are generally two approaches to noise modelling. The first is based on simplified energy flux models, assuming either spherical or cylindrical propagation of sound energy. These models are very quick but they ignore important water column and seabed properties, and produce significant errors in the areas subject to temperature stratification (Shapiro et al., 2014). The second type of model (e.g. ray-tracing and parabolic equation) is based on an advanced physical representation of sound propagation. However, these acoustic propagation models are computationally expensive to execute. Shipping noise modelling requires spatial discretization in order to group noise sources together using a grid. A uniform grid size is often selected to achieve either the greatest efficiency (i.e. speed of computations) or the greatest accuracy. In contrast, this work aims to produce efficient and accurate noise level predictions by presenting an adaptive grid where cell size varies with distance from the receiver. The spatial range over which a certain cell size is suitable was determined by calculating the distance from the receiver at which propagation loss becomes uniform across a grid cell. The computational efficiency and accuracy of the resulting adaptive grid was tested by comparing it to uniform 1 km and 5 km grids. These represent an accurate and computationally efficient grid respectively. For a case study of the Celtic Sea, an application of the adaptive grid over an area of 160×160 km reduced the number of model executions required from 25600 for a 1 km grid to 5356 in December and to between 5056 and 13132 in August, which

  12. Prediction of Tonal Underwater Noise Pattern from Cavitating Propellers with Special Attention to Ice Cover Effects

    Directory of Open Access Journals (Sweden)

    Streckwall Heinrich

    2015-01-01

    Full Text Available To predict underwater noise spectra associated to regular occurrence of propeller cavitation we have extended an existing method [1] (used for the prediction of fluctuating hull pressures to become applicable for effects that are linked to a finite speed of sound. In [2] an intermediate approach was realized where (besides the hull far field boundaries were introduced but the incompressible flow assumption was kept. However compressibility effects become noticeable in the far field, which may be judged to start at some 2-3 propeller-diameters distance from the centre of the cavitation events, if we confine to emissions at 1st-4th blade frequency. It was a logical continuation of our former efforts to realize a compressible flow model and integrate the propeller as a noise source. Having increased the functionality of our approach by referencing the speed of sound, the precision of the method was also somehow reduced. In our former approach, like in comparable approaches (see for instance [3] and [4], the singularity system generating the near field propeller induced pressures involved various sources and vortices distributed on the propeller blades. With our current compressible approach this complexity was dropped, as a single point source substitutes the cavitating propeller. Such a simplification correlates with the assumption, that the monopole character of a noise source is decisive for the far field noise levels. In this contribution we outline the steps characterizing the procedure for predicting tonal underwater noise from cavitating propellers. In the first step a Vortex Lattice Method (VLM is used to access the cavitation pattern on the propeller with special focus on the cavity volume attached to one blade. The second step accumulates the distributed cavities to establish a fluctuating point source of equivalent far field noise characteristic. As relevant limits the hull, the free surface, the sea bottom and an ice cover are

  13. Ambient noise levels and characterization in Aegean region, Turkey

    Science.gov (United States)

    Sevim, Fatih; Zor, Ekrem; Açıkgöz, Cem; Tarancıoğlu, Adil

    2018-03-01

    We assessed the ambient noise level in the Aegean region and analyzed its diurnal variation and its relation to the earthquake detection capability of the Aegean Region Seismic Network (ARSN). We prepared probability density functions (PDFs) for 19 broadband stations in the Aegean region operated by the Earth and Marine Sciences Institute (EMSI) of the Marmara Research Center (MRC) of the Turkish Scientific Research Council (TÜBİTAK). The power spectral densities (PSDs) used to construct PDFs for each station were computed for the periods between 0.02 and 180 s. In addition, we generated noise map of the Aegean region for different periods using the PDFs to assess the origin of the noise. We analyzed earthquake activity in the region and found that there are more local events recorded at night than during the day for each station. This difference is strongly related to diurnal variation of background noise level for the period range mostly covering the frequency range for the local events. We observed daytime noise level 15 to 20 dB higher than that at the nighttime in high frequencies for almost all stations caused by its proximity to settled areas and roads. Additionally, we observed a splitting peak within the Double Frequency (DF) microseism band; it showed a clear noise increase around the short period DF band at all the stations, decreasing inland. This peak may be related to sea waves locally generated in the Aegean Sea. We also identified a prominent increase related to marble saw companies in some stations' noise PDFs.

  14. Ambient noise levels and characterization in Aegean region, Turkey

    Science.gov (United States)

    Sevim, Fatih; Zor, Ekrem; Açıkgöz, Cem; Tarancıoğlu, Adil

    2017-12-01

    We assessed the ambient noise level in the Aegean region and analyzed its diurnal variation and its relation to the earthquake detection capability of the Aegean Region Seismic Network (ARSN). We prepared probability density functions (PDFs) for 19 broadband stations in the Aegean region operated by the Earth and Marine Sciences Institute (EMSI) of the Marmara Research Center (MRC) of the Turkish Scientific Research Council (TÜBİTAK). The power spectral densities (PSDs) used to construct PDFs for each station were computed for the periods between 0.02 and 180 s. In addition, we generated noise map of the Aegean region for different periods using the PDFs to assess the origin of the noise. We analyzed earthquake activity in the region and found that there are more local events recorded at night than during the day for each station. This difference is strongly related to diurnal variation of background noise level for the period range mostly covering the frequency range for the local events. We observed daytime noise level 15 to 20 dB higher than that at the nighttime in high frequencies for almost all stations caused by its proximity to settled areas and roads. Additionally, we observed a splitting peak within the Double Frequency (DF) microseism band; it showed a clear noise increase around the short period DF band at all the stations, decreasing inland. This peak may be related to sea waves locally generated in the Aegean Sea. We also identified a prominent increase related to marble saw companies in some stations' noise PDFs.

  15. Noise Model Analysis and Estimation of Effect due to Wind Driven Ambient Noise in Shallow Water

    Directory of Open Access Journals (Sweden)

    S. Sakthivel Murugan

    2011-01-01

    Full Text Available Signal transmission in ocean using water as a channel is a challenging process due to attenuation, spreading, reverberation, absorption, and so forth, apart from the contribution of acoustic signals due to ambient noises. Ambient noises in sea are of two types: manmade (shipping, aircraft over the sea, motor on boat, etc. and natural (rain, wind, seismic, etc., apart from marine mammals and phytoplanktons. Since wind exists in all places and at all time: its effect plays a major role. Hence, in this paper, we concentrate on estimating the effects of wind. Seven sets of data with various wind speeds ranging from 2.11 m/s to 6.57 m/s were used. The analysis is performed for frequencies ranging from 100 Hz to 8 kHz. It is found that a linear relationship between noise spectrum and wind speed exists for the entire frequency range. Further, we developed a noise model for analyzing the noise level. The results of the empirical data are found to fit with results obtained with the aid of noise model.

  16. Crustal structure of Australia from ambient seismic noise tomography

    Science.gov (United States)

    Saygin, Erdinc; Kennett, B. L. N.

    2012-01-01

    Surface wave tomography for Australian crustal structure has been carried out using group velocity measurements in the period range 1-32 s extracted from stacked correlations of ambient noise between station pairs. Both Rayleigh wave and Love wave group velocity maps are constructed for each period using the vertical and transverse component of the Green's function estimates from the ambient noise. The full suite of portable broadband deployments and permanent stations on the continent have been used with over 250 stations in all and up to 7500 paths. The permanent stations provide a useful link between the various shorter-term portable deployments. At each period the group velocity maps are constructed with a fully nonlinear tomographic inversion exploiting a subspace technique and the Fast Marching Method for wavefront tracking. For Rayleigh waves the continental coverage is good enough to allow the construction of a 3D shear wavespeed model in a two stage approach. Local group dispersion information is collated for a distribution of points across the continent and inverted for a 1D SV wavespeed profile using a Neighbourhood Algorithm method. The resulting set of 1D models are then interpolated to produce the final 3D wavespeed model. The group velocity maps show the strong influence of thick sediments at shorter periods, and distinct fast zones associated with cratonic regions. Below the sediments the 3D shear wavespeed model displays significant heterogeneity with only moderate correlation with surface tectonic features. For example, there is no evident expression of the Tasman Line marking the eastern edge of Precambrian outcrop. The large number of available inter-station paths extracted from the ambient noise analysis provide detailed shear wavespeed information for crustal structure across the Australian continent for the first time, including regions where there was no prior sampling because of difficult logistics.

  17. Ambient noise tomography of Eyjafjallajökull volcano, Iceland

    Science.gov (United States)

    Benediktsdóttir, Ásdís; Gudmundsson, Ólafur; Brandsdóttir, Bryndís; Tryggvason, Ari

    2017-11-01

    We present a shear-velocity model for the Eyjafjallajökull stratovolcano, based on ambient seismic noise tomography applied to seven months of data from six permanent stations and 10 temporary seismic stations, deployed during and after the 2010 volcanic unrest. Vertical components of noise were cross correlated resulting in 30 robust phase-velocity dispersion curves between 1.6 and 6.5 s in period, displaying a ± 20% variation in phase velocity beneath the volcano. The uneven distribution of noise sources, evaluated using signal-to-noise ratios, was estimated to cause less than 2% error in most curves. Sensitivity kernels showed resolution down to 10 km and the lateral resolution of the resulting phase-velocity maps was about 5 km. The model reveals east-west oriented high-velocity anomalies due east and west of the caldera. Between these a zone of lower velocity is identified, coinciding with the location of earthquakes that occurred during the summit eruption in April 2010. A shallow, southwest elongated low-velocity anomaly is located 5 km southwest of the caldera. The limited depth resolution of the shear-velocity model precludes detection of melt within the volcano.

  18. Thirty years of progress in applications and modeling of ocean ambient noise

    Science.gov (United States)

    Siderius, Martin; Buckingham, Michael J.

    2012-11-01

    Ambient noise in the ocean is a stochastic process, which traditionally was considered to be a nuisance, since it reduced the detectability of sonar signals of interest. However, over the last thirty years, it has come to be recognized that the ambient noise itself contains useful information about the ocean and ocean processes. To extract the information, various inversion procedures have been developed, based upon which a number of practical applications of the ambient noise have evolved. Since naturally generated ambient noise is always present in the ocean, it has the advantage of being non-invasive and non-damaging to marine life, including marine mammals. In this article, a summary of the commonly encountered ambient noise models is offered, along with the associated inversion procedures, and some of the more recent applications of the ambient noise are highlighted.

  19. Body Wave and Ambient Noise Tomography of Makushin Volcano, Alaska

    Science.gov (United States)

    Lanza, F.; Thurber, C. H.; Syracuse, E. M.; Ghosh, A.; LI, B.; Power, J. A.

    2017-12-01

    Located in the eastern portion of the Alaska-Aleutian subduction zone, Makushin Volcano is among the most active volcanoes in the United States and has been classified as high threat based on eruptive history and proximity to the City of Unalaska and international air routes. In 2015, five individual seismic stations and three mini seismic arrays of 15 stations each were deployed on Unalaska island to supplement the Alaska Volcano Observatory (AVO) permanent seismic network. This temporary array was operational for one year. Taking advantage of the increased azimuthal coverage and the array's increased earthquake detection capability, we developed body-wave Vp and Vp/Vs seismic images of the velocity structure beneath the volcano. Body-wave tomography results show a complex structure with the upper 5 km of the crust dominated by both positive and negative Vp anomalies. The shallow high-Vp features possibly delineate remnant magma pathways or conduits. Low-Vp regions are found east of the caldera at approximately 6-9 km depth. This is in agreement with previous tomographic work and geodetic models, obtained using InSAR data, which had identified this region as a possible long-term source of magma. We also observe a high Vp/Vs feature extending between 7 and 12 km depth below the caldera, possibly indicating partial melting, although the resolution is diminished at these depths. The distributed stations allow us to further complement body-wave tomography with ambient noise imaging and to obtain higher quality of Vs images. Our data processing includes single station data preparation and station-pair cross-correlation steps (Bensen et al., 2007), and the use of the phase weighted stacking method (Schimmel and Gallart, 2007) to improve the signal-to-noise ratio of the cross-correlations. We will show surface-wave dispersion curves, group velocity maps, and ultimately a 3D Vs image. By performing both body wave and ambient noise tomography, we provide a high

  20. Transdimensional, hierarchical, Bayesian inversion of ambient seismic noise: Australia

    Science.gov (United States)

    Crowder, E.; Rawlinson, N.; Cornwell, D. G.

    2017-12-01

    We present models of crustal velocity structure in southeastern Australia using a novel, transdimensional and hierarchical, Bayesian inversion approach. The inversion is applied to long-time ambient noise cross-correlations. The study area of SE Australia is thought to represent the eastern margin of Gondwana. Conflicting tectonic models have been proposed to explain the formation of eastern Gondwana and the enigmatic geological relationships in Bass Strait, which separates Tasmania and the mainland. A geologically complex area of crustal accretion, Bass Strait may contain part of an exotic continental block entrained in colliding crusts. Ambient noise data recorded by an array of 24 seismometers is used to produce a high resolution, 3D shear wave velocity model of Bass Strait. Phase velocity maps in the period range 2-30 s are produced and subsequently inverted for 3D shear wave velocity structure. The transdimensional, hierarchical Bayesian, inversion technique is used. This technique proves far superior to linearised inversion. The inversion model is dynamically parameterised during the process, implicitly controlled by the data, and noise is treated as an inversion unknown. The resulting shear wave velocity model shows three sedimentary basins in Bass Strait constrained by slow shear velocities (2.4-2.9 km/s) at 2-10 km depth. These failed rift basins from the breakup of Australia-Antartica appear to be overlying thinned crust, where typical mantle velocities of 3.8-4.0 km/s occur at depths greater than 20 km. High shear wave velocities ( 3.7-3.8 km/s) in our new model also match well with regions of high magnetic and gravity anomalies. Furthermore, we use both Rayleigh and Love wave phase data to to construct Vsv and Vsh maps. These are used to estimate crustal radial anisotropy in the Bass Strait. We interpret that structures delineated by our velocity models support the presence and extent of the exotic Precambrian micro-continent (the Selwyn Block) that was

  1. Towards a complete physically based forecast model for underwater noise related to impact pile driving.

    Science.gov (United States)

    Fricke, Moritz B; Rolfes, Raimund

    2015-03-01

    An approach for the prediction of underwater noise caused by impact pile driving is described and validated based on in situ measurements. The model is divided into three sub-models. The first sub-model, based on the finite element method, is used to describe the vibration of the pile and the resulting acoustic radiation into the surrounding water and soil column. The mechanical excitation of the pile by the piling hammer is estimated by the second sub-model using an analytical approach which takes the large vertical dimension of the ram into account. The third sub-model is based on the split-step Padé solution of the parabolic equation and targets the long-range propagation up to 20 km. In order to presume realistic environmental properties for the validation, a geoacoustic model is derived from spatially averaged geological information about the investigation area. Although it can be concluded from the validation that the model and the underlying assumptions are appropriate, there are some deviations between modeled and measured results. Possible explanations for the observed errors are discussed.

  2. Ambient and at-the-ear occupational noise exposure and serum lipid levels

    DEFF Research Database (Denmark)

    Arlien-Søborg, Mai C; Schmedes, Astrid S; Stokholm, Z A

    2016-01-01

    -the-ear occupational noise exposure and serum levels of total cholesterol, low-density lipoprotein-cholesterol, high-density lipoprotein-cholesterol, and triglycerides when accounting for well-established predictors of lipid levels. METHODS: This cross-sectional study included 424 industrial workers and 84 financial...... workers to obtain contrast in noise exposure levels. They provided a serum sample and wore portable dosimeters that every 5-s recorded ambient noise exposure levels during a 24-h period. We extracted measurements obtained during work and calculated the full-shift mean ambient noise level. For 331 workers...... who kept a diary on the use of a hearing protection device (HPD), we subtracted 10 dB from every noise recording obtained during HPD use and estimated the mean full-shift noise exposure level at the ear. RESULTS: Mean ambient noise level was 79.9 dB (A) [range 55.0-98.9] and the mean estimated level...

  3. Ambient Noise Tomography in Koyna-Warna region.

    Science.gov (United States)

    Rohilla, S.; Rao, N. P.; Gerstoft, P.; Yao, H.; Fang, H.; Davulluri, S.

    2017-12-01

    In the present study Ambient Noise tomography has been done in the Koyna-Warna region of western India to decipher the complex structural setting and its linkage to the seismogenesis in this unique Reservoir Triggered Seismicity zone. The 3-D velocity model obtained from the study clearly brings out the lateral and vertical variations of shear velocity in the region down to a depth of about 10 km. In the Koyna region, seismicity distribution along the NNE-SSW trending Donachiwada fault zone is seen coinciding with a low velocity zone between two competent zones with a very high velocity > 4.0 km/s. The seismicity between the Koyna and Warna regions roughly trending NW-SE can be clearly seen in the NE-SW depth sections coinciding with a low velocity zone interspersed between two high velocity zones. The most active seismicity cluster south of the Warna Lake correlates with a near-vertical velocity discontinuity with a contrast of about 0.5 km/s is seen in an EW depth section. The study has helped in delineating the major fault zones of the Koyna-Warna region and enabled understanding the seismogenesis with respect to the structural controls in a RTS enviroment.

  4. Development of a low cost method to estimate the seismic signature of a geothermal field form ambient noise analysis.

    Energy Technology Data Exchange (ETDEWEB)

    Tibuleac, Ileana [Univ. of Nevada, Reno, NV (United States)

    2016-06-30

    A new, cost effective and non-invasive exploration method using ambient seismic noise has been tested at Soda Lake, NV, with promising results. The material included in this report demonstrates that, with the advantage of initial S-velocity models estimated from ambient noise surface waves, the seismic reflection survey, although with lower resolution, reproduces the results of the active survey when the ambient seismic noise is not contaminated by strong cultural noise. Ambient noise resolution is less at depth (below 1000m) compared to the active survey. In general, the results are promising and useful information can be recovered from ambient seismic noise, including dipping features and fault locations.

  5. Circadian Rhythm of Ambient Noise Off the Southeast Coast of India

    Science.gov (United States)

    Kannan, R.; Latha, G.; Prashanthi Devi, M.

    An ambient noise system consisting of a vertical linear hydrophone array was deployed in the shallow waters off Chennai, southeast coast of India from 1 August to 16 September 2013 to record ambient ocean noise of frequencies up to 10kHz. Biological sounds, which are broadband, short duration signals resulting from Terapon theraps, a native species, are a prominent feature of the ocean soundscape. Terapon activity peaks at 8pm and 11pm, and its presence is not observed after 12 midnight in both the months. In the other period, the ambient noise fluctuation is due to wind and vessel traffic. Hence, the present study focuses on the description of the ambient noise fluctuation over two 12h periods, i.e., 12 midnight-12 noon considered as period I, and 12 noon-12 midnight as period II in order to show the circadian rhythm of ambient noise. In this study area, Terapon vocalization reached 25dB above the ambient noise level and it dominates the short-term spectra records in the 0.4-4kHz range. All Terapon signals had daily patterns of sound production with highest levels of activity after dusk during the study period. The result shows that the circadian rhythm of ambient noise is mainly of biological sound generated by Terapon and it is reported first time in the shallow waters off the southeast coast of India.

  6. The Effects of Ambient Conditions on Helicopter Harmonic Noise Radiation: Theory and Experiment

    Science.gov (United States)

    Greenwood, Eric; Sim, Ben W.; Boyd, D. Douglas, Jr.

    2016-01-01

    The effects of ambient atmospheric conditions, air temperature and density, on rotor harmonic noise radiation are characterized using theoretical models and experimental measurements of helicopter noise collected at three different test sites at elevations ranging from sea level to 7000 ft above sea level. Significant changes in the thickness, loading, and blade-vortex interaction noise levels and radiation directions are observed across the different test sites for an AS350 helicopter flying at the same indicated airspeed and gross weight. However, the radiated noise is shown to scale with ambient pressure when the flight condition of the helicopter is defined in nondimensional terms. Although the effective tip Mach number is identified as the primary governing parameter for thickness noise, the nondimensional weight coefficient also impacts lower harmonic loading noise levels, which contribute strongly to low frequency harmonic noise radiation both in and out of the plane of the horizon. Strategies for maintaining the same nondimensional rotor operating condition under different ambient conditions are developed using an analytical model of single main rotor helicopter trim and confirmed using a CAMRAD II model of the AS350 helicopter. The ability of the Fundamental Rotorcraft Acoustics Modeling from Experiments (FRAME) technique to generalize noise measurements made under one set of ambient conditions to make accurate noise predictions under other ambient conditions is also validated.

  7. The influence of ambient noise on maternal behavior in a Bornean sun bear (Helarctos malayanus euryspilus).

    Science.gov (United States)

    Owen, Megan A; Hall, Suzanne; Bryant, Lisa; Swaisgood, Ronald R

    2014-01-01

    Anthropogenic noise has become a pervasive feature of both marine and terrestrial habitats worldwide. While a comprehensive understanding of the biologically significant impacts of noise on wildlife is lacking, concerns regarding its influence persist. Noise is also a common feature in the zoological setting, and much can be learned regarding the species-typical response to ambient noise by studying animals in captivity. Here we correlate behavioral and vocal patterns in a Bornean sun bear (Helarctos malayanus euryspilus) mother and cub with ambient noise levels during the 6-month post-partum period. We hypothesized that loud ambient noise would be correlated with changes in behavior, and predicted that noise would be negatively correlated with maternal care behavior, potentially masking cub vocalizations or providing a distraction to the mother. Contrary to expectation, we found that the mother spent significantly more time attending to her cub (P=0.03) on loud days. We also found that she tended to spend less time feeding (P=0.08); however her time spent resting was not affected. The cub was approximately twice as vocal on loud days, although these results were not statistically significant (humming: P=0.10; squawks/cries: P=0.14). Taken together, these results suggest that the behavioral response to ambient noise may have potential energetic costs, and as a result efforts should be made to reduce ambient noise exposure during the post-partum period. © 2013 Wiley Periodicals, Inc.

  8. Detection capability of the IMS seismic network based on ambient seismic noise measurements

    Science.gov (United States)

    Gaebler, Peter J.; Ceranna, Lars

    2016-04-01

    All nuclear explosions - on the Earth's surface, underground, underwater or in the atmosphere - are banned by the Comprehensive Nuclear-Test-Ban Treaty (CTBT). As part of this treaty, a verification regime was put into place to detect, locate and characterize nuclear explosion testings at any time, by anyone and everywhere on the Earth. The International Monitoring System (IMS) plays a key role in the verification regime of the CTBT. Out of the different monitoring techniques used in the IMS, the seismic waveform approach is the most effective technology for monitoring nuclear underground testing and to identify and characterize potential nuclear events. This study introduces a method of seismic threshold monitoring to assess an upper magnitude limit of a potential seismic event in a certain given geographical region. The method is based on ambient seismic background noise measurements at the individual IMS seismic stations as well as on global distance correction terms for body wave magnitudes, which are calculated using the seismic reflectivity method. From our investigations we conclude that a global detection threshold of around mb 4.0 can be achieved using only stations from the primary seismic network, a clear latitudinal dependence for the detection threshold can be observed between northern and southern hemisphere. Including the seismic stations being part of the auxiliary seismic IMS network results in a slight improvement of global detection capability. However, including wave arrivals from distances greater than 120 degrees, mainly PKP-wave arrivals, leads to a significant improvement in average global detection capability. In special this leads to an improvement of the detection threshold on the southern hemisphere. We further investigate the dependence of the detection capability on spatial (latitude and longitude) and temporal (time) parameters, as well as on parameters such as source type and percentage of operational IMS stations.

  9. Ambient Noise Levels in Acute Neonatal Intensive Care Unit of a Tertiary Referral Hospital

    Directory of Open Access Journals (Sweden)

    Sonia R. B D'Souza

    2017-10-01

    Full Text Available Background: Advances in neonatal care have resulted in improved survival of neonates admitted to the intensive care of the Neonatal Intensive Care Unit (NICU. However, the NCU may be an inappropriate milieu, with presence of overwhelming stimuli, most potent being the continuous presence of noise in the ambience of the NICU. Aim and Objectives: To determine and describe the ambient noise levels in the acute NICU of a tertiary referral hospital. Material and Methods: The ambient noise, in this study was the background sound existing in the environment of the acute NICU of a tertiary referral hospital in South India. The ambient noise levels were analyzed by an audiologist and acoustical engineer using a standardized and calibrated Sound Level Meter (SLM i.e., the Hand Held Analyzer type 2250, Brüel and Kjær, Denmark on a weighted frequency A and reported as dB (A. Results: The ambient noise levels were timed measurements yielded by the SLM in terms of L eq, L as well as L exceeded the standard A 10 Aeqmax levels (Leq< 45 dB, L ≤ 50 dB, and Lmax ≤ 65 10 dB.The L eq ranged from 59.4 to 62.12 dB A. A Ventilators with alarms caused the maximum amount of ambient noise yielding a L Sound Pressure Level AF (SPL of 82.14 dB A. Conclusion: The study has found high levels of ambient noise in the acute NICU. Though there are several measures to reduce the ambient noise levels in the NICU, it is essential to raise awareness among health care personnel regarding the observed ambient noise levels and its effects on neonates admitted to the NICU.

  10. Techniques for Effective Optical Noise Rejection in Amplitude-Modulated Laser Optical Radars for Underwater Three-Dimensional Imaging

    Directory of Open Access Journals (Sweden)

    Francucci M

    2010-01-01

    Full Text Available Amplitude-modulated (AM laser imaging is a promising technology for the production of accurate three-dimensional (3D images of submerged scenes. The main challenge is that radiation scattered off water gives rise to a disturbing signal (optical noise that degrades more and more the quality of 3D images for increasing turbidity. In this paper, we summarize a series of theoretical findings, that provide valuable hints for the development of experimental methods enabling a partial rejection of optical noise in underwater imaging systems. In order to assess the effectiveness of these methods, which range from modulation/demodulation to polarimetry, we carried out a series of experiments by using the laboratory prototype of an AM 3D imager ( = 405 nm for marine archaeology surveys, in course of realization at the ENEA Artificial Vision Laboratory (Frascati, Rome. The obtained results confirm the validity of the proposed methods for optical noise rejection.

  11. Techniques for Effective Optical Noise Rejection in Amplitude-Modulated Laser Optical Radars for Underwater Three-Dimensional Imaging

    Directory of Open Access Journals (Sweden)

    R. Ricci

    2010-01-01

    Full Text Available Amplitude-modulated (AM laser imaging is a promising technology for the production of accurate three-dimensional (3D images of submerged scenes. The main challenge is that radiation scattered off water gives rise to a disturbing signal (optical noise that degrades more and more the quality of 3D images for increasing turbidity. In this paper, we summarize a series of theoretical findings, that provide valuable hints for the development of experimental methods enabling a partial rejection of optical noise in underwater imaging systems. In order to assess the effectiveness of these methods, which range from modulation/demodulation to polarimetry, we carried out a series of experiments by using the laboratory prototype of an AM 3D imager (λ = 405 nm for marine archaeology surveys, in course of realization at the ENEA Artificial Vision Laboratory (Frascati, Rome. The obtained results confirm the validity of the proposed methods for optical noise rejection.

  12. Rayleigh wave tomography in North-China from ambient seismic noise

    OpenAIRE

    Fang, Lihua

    2010-01-01

    2008/2009 The theory and methodology of ambient noise tomography has been studied and applied to North-China successfully. Continuous vertical-component seismograms, spanning the period from January 1, 2007 to February 28, 2008 recorded by 190 broadband stations and 10 very broadband stations, have been used. The cross correlation technique has been applied to ambient noise data recorded by North-China Seismic Array for each station pairs of the array. Rayleigh wave group ve...

  13. Investigation of ambient seismic noise using seismic interferometry in western Montana

    Science.gov (United States)

    Krzywosz, Natalia

    Passive seismic interferometry is a process by which ambient noise data recorded at different seismic stations can be cross-correlated to estimate Green's functions. In the past, both surface waves and body waves have successfully been extracted by cross-correlation of ambient noise data on both regional and global scales. In this study, I have generated Matlab code to simulate an application of seismic interferometry on a synthetic model with pre-defined layers and p-wave velocities. For areas with known velocity models, the Matlab code produced in this study can be used to generate synthetic seismograms, and model the effects of cross-correlation on receiver responses. In order to develop a general understanding of the ambient noise wavefield in western Montana, a spectral analysis program was developed in Matlab. This program is used to process ambient noise data from the Transportable Array (TA) Seismographic Network, and to generate its power spectral density plots and probability density functions. The detailed spectral analysis provides some insight to the ambient noise sources, and their energy distribution throughout western Montana. In addition, an attempt was made to preprocess ambient noise data from the TA array in Matlab for later use. Although preprocessing of the data was successful, limitations in computing power and time, allowed for temporal stacking of only one month of data. The one month period was not long enough to produce Green's functions which contain coherent body waves.

  14. Ambient air pollution, traffic noise and adult asthma prevalence : A BioSHaRE approach

    NARCIS (Netherlands)

    Cai, Yutong; Zijlema, Wilma L.; Doiron, Dany; Blangiardo, Marta; Burton, Paul R.; Fortier, Isabel; Gaye, Amadou; Gulliver, John; de Hoogh, Kees; Hveem, Kristian; Mbatchou, Stephane; Morley, David W; Stolk, Ronald P.; Elliott, Paul; Hansell, Anna L.; Hodgson, Susan

    2017-01-01

    We investigated the effects of both ambient air pollution and traffic noise on adult asthma prevalence, using harmonised data from three European cohort studies established in 2006-2013 (HUNT3, Lifelines and UK Biobank). Residential exposures to ambient air pollution (particulate matter with

  15. Ambient-noise tomography of Katla volcano, south Iceland

    Science.gov (United States)

    Jeddi, Zeinab; Gudmundsson, Olafur; Tryggvason, Ari

    2017-11-01

    A shear-wave velocity model of subglacial Katla volcano, southern Iceland, has been developed using ambient seismic noise tomography based on data from a temporary network operating between May 2011 and August 2013 and permanent stations around the volcano. Phase-velocity dispersion curves were obtained using cross-correlations of vertical components of 136 station pairs and non-linearly inverted for phase-velocity maps between 1.7 and 7.5 s. Local dispersion curves were inverted for shear-velocity variation with depth using a grid search imposing a fixed ice layer at the top. The resulting one-dimensional (1-D) velocity models were combined to obtain a pseudo three-dimensional (3-D) model with estimated lateral resolution of 8 km and depth resolution varying from close to 1 km near the surface to about 8 km at 10 km depth. Shear wave velocities are generally higher within the Katla central volcano than in its surroundings. The most striking feature of the model is a high-velocity anomaly beneath the caldera at > 6 km depth interpreted to be due to cumulates resulting from differentiation of shallower magma intrusions and remelting of subsiding upper crust. No shallow low-velocity anomaly is resolved beneath the central caldera, but a low-velocity region is found at 2-4 km depth beneath the western half of the caldera. VP/VS ratios, estimated from average velocity-depth profiles from surface-wave data and higher frequency P-wave data, are anomalously high (> 1.9) compared to average Icelandic crust, particularly in the top 2-3 km. This is argued not to be an artifact due to lateral refraction or topography. Instead, this anomaly could be explained as an artifact caused by velocity dispersion due to attenuation and a difference in frequency content, and possibly to a degree by the compositional difference between the transalkalic Fe-Ti basalts of Katla and average tholeiitic Icelandic crust.

  16. Observations of shallow water marine ambient sound: the low frequency underwater soundscape of the central Oregon coast.

    Science.gov (United States)

    Haxel, Joseph H; Dziak, Robert P; Matsumoto, Haru

    2013-05-01

    A year-long experiment (March 2010 to April 2011) measuring ambient sound at a shallow water site (50 m) on the central OR coast near the Port of Newport provides important baseline information for comparisons with future measurements associated with resource development along the inner continental shelf of the Pacific Northwest. Ambient levels in frequencies affected by surf-generated noise (f whale vocalizations. Additionally, an increase in spectral levels for frequencies ranging from 35 to 100 Hz is attributed to noise radiated from distant commercial ship commerce. One-second root mean square (rms) sound pressure level (SPLrms) estimates calculated across the 10-840 Hz frequency band for the entire year long deployment show minimum, mean, and maximum values of 84 dB, 101 dB, and 152 dB re 1 μPa.

  17. Underwater Object Segmentation Based on Optical Features

    Directory of Open Access Journals (Sweden)

    Zhe Chen

    2018-01-01

    Full Text Available Underwater optical environments are seriously affected by various optical inputs, such as artificial light, sky light, and ambient scattered light. The latter two can block underwater object segmentation tasks, since they inhibit the emergence of objects of interest and distort image information, while artificial light can contribute to segmentation. Artificial light often focuses on the object of interest, and, therefore, we can initially identify the region of target objects if the collimation of artificial light is recognized. Based on this concept, we propose an optical feature extraction, calculation, and decision method to identify the collimated region of artificial light as a candidate object region. Then, the second phase employs a level set method to segment the objects of interest within the candidate region. This two-phase structure largely removes background noise and highlights the outline of underwater objects. We test the performance of the method with diverse underwater datasets, demonstrating that it outperforms previous methods.

  18. Improving ambient noise cross-correlations in the noisy ocean bottom environment of the Juan de Fuca plate

    Science.gov (United States)

    Tian, Ye; Ritzwoller, Michael H.

    2017-09-01

    Ambient noise tomography exploits seismic ground motions that propagate coherently over long interstation distances. Such ground motions provide information about the medium of propagation that is recoverable from interstation cross-correlations. Local noise sources, which are particularly strong in ocean bottom environments, corrupt ambient noise cross-correlations and compromise the effectiveness of ambient noise tomography. Based on 62 ocean bottom seismometers (OBSs) located on Juan de Fuca (JdF) plate from the Cascadia Initiative experiment and 40 continental stations near the coast of the western United States obtained in 2011 and 2012, we attempt to reduce the effects of local noise on vertical component seismic records across the plate and onto US continent. The goal is to provide better interstation cross-correlations for use in ambient noise tomography and the study of ambient noise directionality. As shown in previous studies, tilt and compliance noise are major sources of noise that contaminate the vertical channels of the OBSs and such noise can be greatly reduced by exploiting information on the horizontal components and the differential pressure gauge records, respectively. We find that ambient noise cross-correlations involving OBSs are of significantly higher signal-to-noise ratio at periods greater than 10 s after reducing these types of noise, particularly in shallow water environments where tilt and compliance noise are especially strong. The reduction of tilt and compliance noise promises to improve the accuracy and spatial extent of ambient noise tomography, allowing measurements based on coherently propagating ambient noise to be made at stations in the shallower parts of the JdF plate and at longer periods than in previous studies. In addition such local noise reduction produces better estimates of the azimuthal content of ambient noise.

  19. Electrical and noise characteristics of graphene field-effect transistors: ambient effects, noise sources and physical mechanisms.

    Science.gov (United States)

    Rumyantsev, S; Liu, G; Stillman, W; Shur, M; Balandin, A A

    2010-10-06

    We fabricated a large number of single and bilayer graphene transistors and carried out a systematic experimental study of their low-frequency noise characteristics. Special attention was given to determining the dominant noise sources in these devices and the effect of aging on the current-voltage and noise characteristics. The analysis of the noise spectral density dependence on the area of graphene channel showed that the dominant contributions to the low-frequency electronic noise come from the graphene layer itself rather than from the contacts. Aging of graphene transistors due to exposure to ambient conditions for over a month resulted in substantially increased noise, attributed to the decreasing mobility of graphene and increasing contact resistance. The noise spectral density in both single and bilayer graphene transistors either increased with deviation from the charge neutrality point or depended weakly on the gate bias. This observation confirms that the low-frequency noise characteristics of graphene transistors are qualitatively different from those of conventional silicon metal-oxide-semiconductor field-effect transistors.

  20. Spatial correlation in the ambient core noise field of a turbofan engine.

    Science.gov (United States)

    Miles, Jeffrey Hilton

    2012-06-01

    An acoustic transfer function relating combustion noise and turbine exit noise in the presence of enclosed ambient core noise is investigated using a dynamic system model and an acoustic system model for the particular turbofan engine studied and for a range of operating conditions. Measurements of cross-spectra magnitude and phase between the combustor and turbine exit and auto-spectra at the turbine exit and combustor are used to show the presence of indirect and direct combustion noise over the frequency range of 0-400 Hz. The procedure used evaluates the ratio of direct to indirect combustion noise. The procedure used also evaluates the post-combustion residence time in the combustor which is a factor in the formation of thermal NO(x) and soot in this region. These measurements are masked by the ambient core noise sound field in this frequency range which is observable since the transducers are situated within an acoustic wavelength of one another. An ambient core noise field model based on one and two dimensional spatial correlation functions is used to replicate the spatially correlated response of the pair of transducers. The spatial correlation function increases measured attenuation due to destructive interference and masks the true attenuation of the turbine.

  1. Report of the Workshop on International Harmonisation of Approaches to Define Underwater Noise Exposure Criteria (Budapest, Hungary 17th August 2013)

    NARCIS (Netherlands)

    Lucke, K.; Winter, H.V.; Lam, F.P.; Scowcroft, G.; Hawkins, A.; Popper, A.N.

    2013-01-01

    The potential negative effects of high levels of underwater noise on marine life have been identified and acknowledged, and this issue has been incorporated into various international agreements over the past decade. Several countries have already issued regulations to limit the incidence and level

  2. Improving Seismic Velocity Models with Constraints from Autocorrelation of Ambient Seismic Noise and Signal

    Science.gov (United States)

    2016-03-24

    AFRL-RV-PS- AFRL-RV-PS- TR-2016-0098 TR-2016-0098 IMPROVING SEISMIC VELOCITY MODELS WITH CONSTRAINTS FROM AUTOCORRELATION OF AMBIENT SEISMIC ...TYPE Final Report 3. DATES COVERED (From - To) 24 Apr 2014 – 24 Mar 2016 4. TITLE AND SUBTITLE Improving Seismic Velocity Models with Constraints from...Autocorrelation of Ambient Seismic Noise and Signal 5a. CONTRACT NUMBER FA9453-14-C-0214 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 62601F 6

  3. Underwater noise reduction of marine pile driving using a double pile.

    Science.gov (United States)

    2015-12-01

    Impact pile driving of steel piles in marine environments produces extremely high sound levels in the water. : It has been shown that current pile driving noise attenuation techniques, such as bubble curtains and : cofferdams, provide limited noise r...

  4. Noiseonomics: the relationship between ambient noise levels in the sea and global economic trends.

    Science.gov (United States)

    Frisk, George V

    2012-01-01

    In recent years, the topic of noise in the sea and its effects on marine mammals has attracted considerable attention from both the scientific community and the general public. Since marine mammals rely heavily on acoustics as a primary means of communicating, navigating, and foraging in the ocean, any change in their acoustic environment may have an impact on their behavior. Specifically, a growing body of literature suggests that low-frequency, ambient noise levels in the open ocean increased approximately 3.3 dB per decade during the period 1950-2007. Here we show that this increase can be attributed primarily to commercial shipping activity, which in turn, can be linked to global economic growth. As a corollary, we conclude that ambient noise levels can be directly related to global economic conditions. We provide experimental evidence supporting this theory and discuss its implications for predicting future noise levels based on global economic trends.

  5. Self-organizing map and its application in the analysis of ambient noise characteristics

    Science.gov (United States)

    Meng, Chunxia; Li, Guijuan; Che, Shuwei; Bai, Jin

    2017-01-01

    The Self-organizing map (SOM) is an unsupervised neural network based on competitive learning, and can solve the problem that the center of clustering is unknown. SOM's theory and the implementation of algorithm are studied in this paper. Simulating example is given to approve the feasibility of SOM in characteristic assessment for multivariate sample. The Ambient sea noise measurement is made in August 2014 on some sea of China. The total source level was forecasted using "ROSS formula" and the sailing information. The statistical variability of broadband ambient noise at frequencies between 20Hz and 31.5 kHz is obtained using SOM. The comparison between measured sound pressure and forecasting pressure is given, and the preliminary analysis of the relationship between ambient noise level and vessels is carried out. The results provide the technical reference to understand the temporal and spatial statistical variability of ambient noise, and are an efficient tool in assessing the potential effect of shipping noise on marine mammals in the special sea area.

  6. How Might We Assess and Manage the Effects of Underwater Noise on Populations of Marine Animals?

    Science.gov (United States)

    Tasker, Mark L

    2016-01-01

    The European Union Marine Strategy Framework Directive (MSFD) aims to achieve good environmental status (GES) in European seas by 2020. One of the features of GES is that underwater sound should not adversely affect the marine environment. Direct injury of marine life may occur, but a more pervasive effect is likely to be through the cumulative indirect effects on behavior. Assessing the significance of these effects on an ecosystem scale is difficult. If subsequent management of these effects is required, complex and challenging international decisions will be required.

  7. Effects of bladdered fish on ambient noise measurements close to the port of Rotterdam

    NARCIS (Netherlands)

    Ainslie, M.A.; Jong C.A.F. de; Dreschler, J.

    2011-01-01

    Ambient noise in the frequency range 25 Hz to 80 kHz was measured at a site close to the Port of Rotterdam in September 2008, before construction began of a port extension known as ‘Maasvlakte 2’ [http://www.maasvlakte2.com/en/index/], and in September-October 2009 (during construction). Day-night

  8. Horizontal Directionality of Ambient Sea Noise in the North Pacific Ocean

    Science.gov (United States)

    1976-05-01

    interpreting the horizontal directionalit- of the ambient noise shown in figures 11, 12" and 13. This location was in the transpacific shipping lanes...types of errors encountered when determining horizontal arrival angles for the beam response data. The first is due to the angular nature of both the

  9. Ambient Seismic Noise Tomography of a Loess High Bank at Dunaszekcső (Hungary)

    Czech Academy of Sciences Publication Activity Database

    Szanyi, G.; Gráczer, Z.; Györi, E.; Kaláb, Zdeněk; Lednická, Markéta

    2016-01-01

    Roč. 173, č. 8 (2016), s. 2913-2928 ISSN 0033-4553 Institutional support: RVO:68145535 Keywords : seismic interferometry * ambient noise * group velocity * tomography * landslide * high bank Subject RIV: DC - Siesmology, Volcanology, Earth Structure Impact factor: 1.591, year: 2016 http://link.springer.com/article/10.1007/s00024-016-1304-1

  10. Significance of geological units of the Bohemian Massif, Czech Republic, as seen by ambient noise interferometry

    Czech Academy of Sciences Publication Activity Database

    Růžek, Bohuslav; Valentová, L.; Gallovič, F.

    2016-01-01

    Roč. 173, č. 5 (2016), s. 1663-1682 ISSN 0033-4553 R&D Projects: GA ČR GAP210/12/2336; GA MŠk LM2010008 Institutional support: RVO:67985530 Keywords : ambient noise * geological units * Bohemian Massif * velocity model Subject RIV: DC - Siesmology, Volcanology, Earth Structure Impact factor: 1.591, year: 2016

  11. Sub-bottom profiling with ambient noise measured on a drifting vertical array

    NARCIS (Netherlands)

    Harrison, C.H.; Schippers, P.; Snellen, M.; Weterings, A.

    2005-01-01

    The angle and frequency dependent reflective properties of the seabed can be determined from beam-steered ambient noise measurements on a vertical array of hydrophones. From the up-to-down ratio the beam-smeared modulus square of the plane wave reflection coefficient is obtained. Geo-acoustic

  12. The crustal structure beneath The Netherlands derived from ambient seismic noise

    NARCIS (Netherlands)

    Yudistira, Tedi; Paulssen, Hanneke; Trampert, Jeannot

    2017-01-01

    This work presents the first comprehensive 3-D model of the crust beneath The Netherlands. To obtain this model, we designed the NARS-Netherlands project, a dense deployment of broadband stations in the area. Rayleigh and Love wave group velocity dispersion was measured from ambient noise

  13. The crustal structure beneath the Netherlands inferred from ambient seismic noise

    NARCIS (Netherlands)

    Yudistira, T.

    2015-01-01

    A 3-D shear velocity model of the crust beneath the Netherlands is determined from fundamental mode Rayleigh and Love wave group measurements derived from ambient seismic noise recordings. The data are obtained from a temporary array of broad-band seismometers in and around the Netherlands (the

  14. The effects of music, white noise, and ambient noise on sedation and anxiety in patients under spinal anesthesia during surgery.

    Science.gov (United States)

    Ilkkaya, Nazan Koylu; Ustun, Faik Emre; Sener, Elif Bengi; Kaya, Cengiz; Ustun, Yasemin Burcu; Koksal, Ersin; Kocamanoglu, Ismail Serhat; Ozkan, Fatih

    2014-10-01

    To compare effects of music, white noise, and ambient (background) noise on patient anxiety and sedation. Open, parallel, and randomized controlled trial. Seventy-five patients aged 18 to 60 years who were scheduled for surgical procedures under spinal anesthesia were randomly assigned to ambient noise (Group O), white noise (Group B), or music groups (Group M). We evaluated patients' anxiety and sedation levels via the Observer's Assessment of Alertness/Sedation (OAA/S) scale and the State-Trait Anxiety Inventory (STAI) questionnaire. At 5 minutes before surgery, the STAI-State Anxiety Inventory (SA) value was significantly lower in Group M than the other groups. At 30-minute recovery, Group M showed significantly lower STAI-SA values than the other groups. Patient satisfaction was highest in Group M. OAA/S values were not significantly different between groups during any period (P > .05). We suggest that patient-selected music reduces perioperative anxiety and contributes to patient satisfaction during the perioperative period. Copyright © 2014 American Society of PeriAnesthesia Nurses. Published by Elsevier Inc. All rights reserved.

  15. Measuring changes in ambient noise levels from the installation and operation of a surge wave energy converter in the coastal ocean

    Energy Technology Data Exchange (ETDEWEB)

    Haxel, Joe H [Oregon State Univ., Newport, OR (United States); Henkel, Sarah K [Oregon State Univ., Newport, OR (United States)

    2017-10-18

    Ecosystem impacts resulting from elevated underwater noise levels generated by anthropogenic activities in the coastal ocean are poorly understood and remain difficult to address as a result of a significant gap in knowledge for existing nearshore sound levels. Ambient noise is an important habitat component for marine mammals and fish that use sound for essential functions such as communication, navigation, and foraging. Questions surrounding the amplitudes, frequency distributions, and durations of noise emissions from renewable wave energy conversion (WEC) projects during their construction and operation present concerns for long-term consequences in marine habitats. Oregon’s dynamic nearshore environment presents significant challenges for passive acoustic monitoring that include flow noise contamination from wave orbital motions, turbulence from breaking surf, equipment burial, and fishing pressure from sport and commercial crabbers. This project included 2 techniques for passive acoustic data collection: 1) campaign style deployments of fixed hydrophone lander stations to capture temporal variations in noise levels and 2) a drifting hydrophone system to record spatial variations within the project site. The hydrophone lander deployments were effective and economically feasible for enabling robust temporal measurements of ambient noise levels in a variety of sea state conditions. Limiting factors for the fixed stations included 1) a flow shield mitigation strategy failure in the first deployment resulting in significant wideband data contamination and 2) flow noise contamination of the unshielded sensors restricting valuable analysis to frequencies above 500 Hz for subsequent deployments. Drifting hydrophone measurements were also effective and economically feasible (although logistically challenging in the beginning of the project due to vessel time constraints) providing a spatial distribution of sound levels, comparisons of noise levels in varying levels

  16. High ambient noise levels in Vadodara City, India, affected by urbanization.

    Science.gov (United States)

    Singh, Neha; Dhiman, Hitesh; Shaikh, Sadaf; Shah, Purvish; Sarkar, Roma; Patel, Shashin

    2016-12-01

    The present research was conducted to study the urbanization of Vadodara city and to monitor the ambient noise level in the industrial, commercial, residential and silence zones of the city. A settlement map created by unsupervised classification for the land use and land cover study of Vadodara city clearly shows the increasing pattern of urbanization in its central part, which may be the result of urban sprawl due to migration of people from the rural to the urban areas. The fluctuation in ambient noise level was recorded using an A-weighted sound level meter in all the four zones of Vadodara city for 3 h at regular intervals of 15 min on 3 consecutive days at the same time. The results showed the highest equivalent noise level of 93.7 dBA in the commercial zone followed by 85.5 dBA in the industrial zone, 73.2 dBA in silence zone, and 70.2 dBA in the residential zone. The values of noise level were high in all the zones of the city increasing remarkably over the prescribed limit given in the Noise Pollution (Control and Regulation) Rules, 2000. Continuous exposure to such high level of noise may lead to detrimental effect on people.

  17. Ambient noise forecasting with a large acoustic array in a complex shallow water environment.

    Science.gov (United States)

    Rogers, Jeffrey S; Wales, Stephen C; Means, Steven L

    2017-11-01

    Forecasting ambient noise levels in the ocean can be a useful way of characterizing the detection performance of sonar systems and projecting bounds on performance into the near future. The assertion is that noise forecasting can be improved with a priori knowledge of source positions coupled with the ability to resolve closely separated sources in bearing. One example of such a system is the large aperture research array located at the South Florida Test Facility. Given radar and Automatic Identification System defined source positions and environmental information, transmission loss (TL) is computed from known source positions to the array. Source levels (SLs) of individual ships are then estimated from computed TL and the pre-determined beam response of the array using a non-negative least squares algorithm. Ambient noise forecasts are formed by projecting the estimated SLs along known ship tracks. Ambient noise forecast estimates are compared to measured beam level data and mean-squared error is computed. A mean squared error as low as 3.5 dB is demonstrated in 30 min forecast estimates when compared to ground truth.

  18. Stress Monitoring Potential of Ambient Noise Interferometry in Deep Mine Environments

    Science.gov (United States)

    Dales, P.; Audet, P.; Mercier, J. P.; de Beer, W.; Pascu, A.

    2015-12-01

    Understanding the response of the rock mass to mining is of key importance for the planning of mine operations as well as assessing and mitigating the seismic risk. For decades, studies have shown that passive source tomography, also called local earthquake tomography, can provide information on the rock mass response through the estimation of the temporal variation and 3D distribution (spatio-temporal variations) of stress. The spatio-temporal resolution afforded by passive source tomography depends on the seismicity rate and the location of microseismic events. In a mine, seismicity is not stationary, i.e. the locus and rate of seismicity vary with time, thus limiting the spatio-temporal resolution of this technique. Recent developments in the field of ambient noise seismic interferometry (Green's function retrieval from ambient noise) provide hints that continuous recordings of ambient vibrations collected around mines could be used to obtain information on the evolution and 3D distribution of the stress in the rock mass by providing measures of seismic travel times between pairs of sensors. In contrast to passive source tomography that relies on the distribution of seismic events, the resolution afforded by ambient noise interferometry tomography depends solely on the locations of sensors and the frequency content of the ambient noise. We present preliminary results which focus on the temporal stability of the estimated Green's functions, the effect of mine infrastructure on signal quality and preliminary methods to quantify stress changes in the rock mass. In addition, we present the adopted processing scheme built on the Apache Spark engine and demonstrate its effectiveness in parallelizing the computationally intensive cross-correlation routines.

  19. Icequakes and ambient noise sources detected by a geophone array at the Kaskawulsh glacier

    Science.gov (United States)

    Aso, N.; Tsai, V. C.; Schoof, C.; Whiteford, A.; Flowers, G. E.

    2015-12-01

    Both sliding and meltwater drainage processes of glaciers are expected to generate seismic signals. The confluence of the North and Central arms of the Kaskawulsh glacier in the Yukon Territory is an especially attractive place to study such phenomena not only because of the confluence but also because a nearby ice-dammed lake fills and drains rapidly every summer. We analyzed geophone data from nine stations at the Kaskawulsh glacier during the summer of 2014 to detect and locate icequakes and ambient noise sources. We first detected icequakes automatically by picking arrivals. Then we located events using differential arrival times between stations obtained precisely by cross-correlations, and also applied a double-difference relocation technique. During the 1-month observation period, we found 183 events that clustered near the medial moraine. More icequakes are observed from midnight to noon, potentially due to lower noise levels. These events are distributed on a dipping plane sub-parallel to the glacier flow direction. The depths below the surface range from 200m on the shallower side to 500m on the deeper side. This structure may correspond to the basal slope of the medial moraine and implies that these icequake signals come from either shear basal sliding or an englacial splay fault. We also determined ambient noise source locations for each 1-hour record sequence using the same process as for the icequakes. We located 31 sequences, among which more sequences were observed in the afternoon, possibly related to melting of the glacier. Most of the ambient noise sequences were located in two vertical clusters, with each cluster potentially corresponding to a crevasse or a moulin. We interpret this ambient noise as being produced by meltwater drainage. In both analyses, we find that inter-station differential arrival times obtained by cross-correlations provide effective information to locate sliding or meltwater drainage processes.

  20. Frequency Dependent Polarization Analysis of Ambient Seismic Noise Recorded at Broadband Seismometers

    Science.gov (United States)

    Koper, K.; Hawley, V.

    2010-12-01

    Analysis of ambient seismic noise is becoming increasingly relevant to modern seismology. Advances in computational speed and storage have made it feasible to analyze years and even decades of continuous seismic data in short amounts of time. Therefore, it is now possible to perform longitudinal studies of station performance in order to identify degradation or mis-installation of seismic equipment. Long-term noise analysis also provides insight into the evolution of the ocean wave climate, specifically whether the frequency and intensity of storms have changed as global temperatures have changed. Here we present a new approach to polarization analysis of seismic noise recorded by three-component seismometers. Essentially, eigen-decomposition of the 3-by-3 Hermitian spectral matrix associated with a sliding window of data is applied to yield various polarization attributes as a function of time and frequency. This in turn yields fundamental information about the composition of seismic noise, such as the extent to which it is polarized, its mode of propagation, and the direction from which it arrives at the seismometer. The polarization attributes can be viewed as function of time or binned over 2D frequency-time space to deduce regularities in the ambient noise that are unbiased by transient signals from earthquakes and explosions. We applied the algorithm to continuous data recorded in 2009 by the seismic station SLM, located in central North America. A rich variety of noise sources was observed. At low frequencies (3 Hz), Rayleigh-type energy was again dominant, in the form of Rg waves created by nearby cultural activities. Analysis of the time dependence of noise power shows that a frequency range of at least 0.02-1.0 Hz (much larger than the microseism band) is sensitive to annual, meteorologically induced sources of noise. We are currently applying our technique to selected seismometers from USArray and the University of Utah Seismic Network.

  1. Optimal filter design for shielded and unshielded ambient noise reduction in fetal magnetocardiography

    Science.gov (United States)

    Comani, S.; Mantini, D.; Alleva, G.; Di Luzio, S.; Romani, G. L.

    2005-12-01

    The greatest impediment to extracting high-quality fetal signals from fetal magnetocardiography (fMCG) is environmental magnetic noise, which may have peak-to-peak intensity comparable to fetal QRS amplitude. Being an unstructured Gaussian signal with large disturbances at specific frequencies, ambient field noise can be reduced with hardware-based approaches and/or with software algorithms that digitally filter magnetocardiographic recordings. At present, no systematic evaluation of filters' performances on shielded and unshielded fMCG is available. We designed high-pass and low-pass Chebychev II-type filters with zero-phase and stable impulse response; the most commonly used band-pass filters were implemented combining high-pass and low-pass filters. The achieved ambient noise reduction in shielded and unshielded recordings was quantified, and the corresponding signal-to-noise ratio (SNR) and signal-to-distortion ratio (SDR) of the retrieved fetal signals was evaluated. The study regarded 66 fMCG datasets at different gestational ages (22-37 weeks). Since the spectral structures of shielded and unshielded magnetic noise were very similar, we concluded that the same filter setting might be applied to both conditions. Band-pass filters (1.0-100 Hz) and (2.0-100 Hz) provided the best combinations of fetal signal detection rates, SNR and SDR; however, the former should be preferred in the case of arrhythmic fetuses, which might present spectral components below 2 Hz.

  2. A survey of models for the prediction of ambient ocean noise: Circa 1995

    Energy Technology Data Exchange (ETDEWEB)

    Doolittle, R.

    1996-01-01

    The state of the art of model development for application to computer studies of undersea search systems utilizing acoustics is surveyed in this document. Due to the demands for surveillance of submarines operating in ocean basins, the development of noise models for application in deep oceans is fairly advanced and somewhat generic. This is due to the deep sound channel, discovered during World War II, which when present allows for long-range sound propagation with little or no interaction with the bottom. Exceptions to this channel, also well understood, are found in both the high latitudes where the sound is upward refracting and in tropical ocean areas with downward refracting sound transmission. The controlling parameter is the sound speed as a function of depth within the ocean, the sound speed profile. When independent of range, this profile may be converted to a noise-versus-depth profile with well-validated consequences for deep-ocean ambient noise. When considering ocean areas of shallow water, the littoral regions, the idea of a genenic ocean channel advisedly is abandoned. The locally unique nature of both the noise production mechanisms and of the channel carrying the sound, obviates the generic treatment. Nevertheless, idealizations of this case exist and promote the understanding if not the exact predictability of the statistics of shallow water ambient noise. Some examples of these models are given in this document.

  3. Optimal filter design for shielded and unshielded ambient noise reduction in fetal magnetocardiography

    International Nuclear Information System (INIS)

    Comani, S; Mantini, D; Alleva, G; Luzio, S Di; Romani, G L

    2005-01-01

    The greatest impediment to extracting high-quality fetal signals from fetal magnetocardiography (fMCG) is environmental magnetic noise, which may have peak-to-peak intensity comparable to fetal QRS amplitude. Being an unstructured Gaussian signal with large disturbances at specific frequencies, ambient field noise can be reduced with hardware-based approaches and/or with software algorithms that digitally filter magnetocardiographic recordings. At present, no systematic evaluation of filters' performances on shielded and unshielded fMCG is available. We designed high-pass and low-pass Chebychev II-type filters with zero-phase and stable impulse response; the most commonly used band-pass filters were implemented combining high-pass and low-pass filters. The achieved ambient noise reduction in shielded and unshielded recordings was quantified, and the corresponding signal-to-noise ratio (SNR) and signal-to-distortion ratio (SDR) of the retrieved fetal signals was evaluated. The study regarded 66 fMCG datasets at different gestational ages (22-37 weeks). Since the spectral structures of shielded and unshielded magnetic noise were very similar, we concluded that the same filter setting might be applied to both conditions. Band-pass filters (1.0-100 Hz) and (2.0-100 Hz) provided the best combinations of fetal signal detection rates, SNR and SDR; however, the former should be preferred in the case of arrhythmic fetuses, which might present spectral components below 2 Hz

  4. Vertical line array measurements of ambient noise in the North Pacific.

    Science.gov (United States)

    Farrokhrooz, Mehdi; Wage, Kathleen E; Dzieciuch, Matthew A; Worcester, Peter F

    2017-03-01

    Shipping noise and wind are the dominant sources of ocean noise in the frequency band between 20 and 500 Hz. This paper analyzes noise in that band using data from the SPICEX experiment, which took place in the North Pacific in 2004-2005, and compares the results with other North Pacific experiments. SPICEX included vertical arrays with sensors above and below the surface conjugate depth, facilitating an analysis of the depth dependence of ambient noise. The paper includes several key results. First, the 2004-05 noise levels at 50 Hz measured in SPICEX had not increased relative to levels measured by Morris [(1978). J. Acoust. Soc. Am. 64, 581-590] at a nearby North Pacific site three decades earlier, but rather were comparable to those levels. Second, at 50 Hz the noise below the conjugate depth decreases at a rate of -9.9 dB/km, which is similar to the rate measured by Morris and much less than the rate measured by Gaul, Knobles, Shooter, and Wittenborn [(2007). IEEE J. Ocean. Eng. 32, 497-512] for the CHURCH OPAL experiment. Finally, the paper describes the seasonal trends in noise over the year-long time series of the measurements.

  5. Spatial Vertical Directionality and Correlation of Low-Frequency Ambient Noise in Deep Ocean Direct-Arrival Zones.

    Science.gov (United States)

    Yang, Qiulong; Yang, Kunde; Cao, Ran; Duan, Shunli

    2018-01-23

    Wind-driven and distant shipping noise sources contribute to the total noise field in the deep ocean direct-arrival zones. Wind-driven and distant shipping noise sources may significantly and simultaneously affect the spatial characteristics of the total noise field to some extent. In this work, a ray approach and parabolic equation solution method were jointly utilized to model the low-frequency ambient noise field in a range-dependent deep ocean environment by considering their calculation accuracy and efficiency in near-field wind-driven and far-field distant shipping noise fields. The reanalysis databases of National Center of Environment Prediction (NCEP) and Volunteer Observation System (VOS) were used to model the ambient noise source intensity and distribution. Spatial vertical directionality and correlation were analyzed in three scenarios that correspond to three wind speed conditions. The noise field was dominated by distant shipping noise sources when the wind speed was less than 3 m/s, and then the spatial vertical directionality and vertical correlation of the total noise field were nearly consistent with those of distant shipping noise field. The total noise field was completely dominated by near field wind generated noise sources when the wind speed was greater than 12 m/s at 150 Hz, and then the spatial vertical correlation coefficient and directionality pattern of the total noise field was approximately consistent with that of the wind-driven noise field. The spatial characteristics of the total noise field for wind speeds between 3 m/s and 12 m/s were the weighted results of wind-driven and distant shipping noise fields. Furthermore, the spatial characteristics of low-frequency ambient noise field were compared with the classical Cron/Sherman deep water noise field coherence function. Simulation results with the described modeling method showed good agreement with the experimental measurement results based on the vertical line array deployed near

  6. Upper crustal structure of Madeira Island revealed from ambient noise tomography

    Science.gov (United States)

    Matos, Catarina; Silveira, Graça; Matias, Luís; Caldeira, Rita; Ribeiro, M. Luísa; Dias, Nuno A.; Krüger, Frank; Bento dos Santos, Telmo

    2015-06-01

    We present the first image of the Madeira upper crustal structure, using ambient seismic noise tomography. 16 months of ambient noise, recorded in a dense network of 26 seismometers deployed across Madeira, allowed reconstructing Rayleigh wave Green's functions between receivers. Dispersion analysis was performed in the short period band from 1.0 to 4.0 s. Group velocity measurements were regionalized to obtain 2D tomographic images, with a lateral resolution of 2.0 km in central Madeira. Afterwards, the dispersion curves, extracted from each cell of the 2D group velocity maps, were inverted as a function of depth to obtain a 3D shear wave velocity model of the upper crust, from the surface to a depth of 2.0 km. The obtained 3D velocity model reveals features throughout the island that correlates well with surface geology and island evolution.

  7. Experimental assessment of the insertion loss of an underwater noise mitigation screen for marine pile driving

    NARCIS (Netherlands)

    Jansen, H.W.; Jong, C.A.F. de; Jung, B.

    2012-01-01

    Because of the concern about potential effects on marine pile driving, the industry is developing silent marine pile driving concepts. One of the new concepts, which has been engineered by IHC Hydrohammer in the Netherlands, is the application of a steel Noise Mitigation Screen (NMS) around the pile

  8. Ocean Basin Impact of Ambient Noise on Marine Mammal Detectability, Distribution, and Acoustic Communication - YIP

    Science.gov (United States)

    2014-09-30

    Detectability, Distribution, and Acoustic Communication - YIP Jennifer L. Miksis-Olds Applied Research Laboratory The Pennsylvania State University...5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Pennsylvania State University,Applied Research Laboratory ,PO...0039 to David Bradley titled “Ambient Noise Analysis from Selected CTBTO Hydroacoustic Sites”. Patterns and trends of ocean sound observed in this

  9. Ambient Noise Tomography Applied to Nodal Data Sets in Induced Seismicity Regions

    Science.gov (United States)

    Sufri, O.; DeShon, H. R.; Ogwari, P.; Hayward, C.; Magnani, M. B.

    2017-12-01

    We present results of ambient noise tomography performed using nodal datasets with different array apertures and geometries deployed in northern Texas and northern Oklahoma to capture induced earthquakes. We show that ambient noise tomography techniques can be performed on small aperture, oddly shaped array datasets. In northern Texas, the nodal data was collected on 10 Hz single-component vertical sensors that were deployed from the collaboration between SMU and Nodal Seismic. The data was acquired between 25 February and 8 March 2014. First, we compute the cross-correlation between the geophone pairs, which are used as Green's functions to perform ambient noise tomography, and find acceptable results between 0.3-1.0 seconds. We compute the phase velocities for these periods and invert the phase velocities to obtain shear wave velocity structure for up to depths of 200 meters underneath the array. The small aperture of the array (2.6 km x 2.92 km) limits depth resolution. The resulting shear wave velocity model is then used as a shallow velocity constraint to improve double-difference local earthquake tomography using the earthquake data from a co-located local seismic network. We present tomography results aimed at resolving 3D velocity heterogeneity associated with the 2013-2015 Azle-Reno induced earthquake sequence. These techniques are also applied to conduct ambient noise tomography in northern Oklahoma using the IRIS Wavefield Community Experiment data. This data was acquired between 23 June and 20 July 2016 from a larger (6 km x 14 km) aperture array consisting of 5 Hz 3-component nodes. Because the aperture of Wavefield network was larger than the north Texas array, we expect to resolve shear velocity to greater depth and provide 3D information on near surface velocity heterogeneity, and possibly resolve faulting associated with earthquakes beneath the array.

  10. Wind dependence of ambient noise in a biologically rich coastal area.

    Science.gov (United States)

    Mathias, Delphine; Gervaise, Cédric; Di Iorio, Lucia

    2016-02-01

    The wind dependence of acoustic spectrum between 100 Hz and 16 kHz is investigated for coastal biologically rich areas. The analysis of 5 months of continuous measurements run in a 10 m deep shallow water environment off Brittany (France) showed that wind dependence of spectral levels is subject to masking by biological sounds. When dealing with raw data, the wind dependence of spectral levels was not significant for frequencies where biological sounds were present (2 to 10 kHz). An algorithm developed by Kinda, Simard, Gervaise, Mars, and Fortier [J. Acoust. Soc. Am. 134(1), 77-87 (2013)] was used to automatically filter out the loud distinctive biological contribution and estimated the ambient noise spectrum. The wind dependence of ambient noise spectrum was always significant after application of this filter. A mixture model for ambient noise spectrum which accounts for the richness of the soundscape is proposed. This model revealed that wind dependence holds once the wind speed was strong enough to produce sounds higher in amplitude than the biological chorus (9 kn at 3 kHz, 11 kn at 8 kHz). For these higher wind speeds, a logarithmic affine law was adequate and its estimated parameters were compatible with previous studies (average slope 27.1 dB per decade of wind speed increase).

  11. The Effects of Ambient Conditions on Helicopter Rotor Source Noise Modeling

    Science.gov (United States)

    Schmitz, Frederic H.; Greenwood, Eric

    2011-01-01

    A new physics-based method called Fundamental Rotorcraft Acoustic Modeling from Experiments (FRAME) is used to demonstrate the change in rotor harmonic noise of a helicopter operating at different ambient conditions. FRAME is based upon a non-dimensional representation of the governing acoustic and performance equations of a single rotor helicopter. Measured external noise is used together with parameter identification techniques to develop a model of helicopter external noise that is a hybrid between theory and experiment. The FRAME method is used to evaluate the main rotor harmonic noise of a Bell 206B3 helicopter operating at different altitudes. The variation with altitude of Blade-Vortex Interaction (BVI) noise, known to be a strong function of the helicopter s advance ratio, is dependent upon which definition of airspeed is flown by the pilot. If normal flight procedures are followed and indicated airspeed (IAS) is held constant, the true airspeed (TAS) of the helicopter increases with altitude. This causes an increase in advance ratio and a decrease in the speed of sound which results in large changes to BVI noise levels. Results also show that thickness noise on this helicopter becomes more intense at high altitudes where advancing tip Mach number increases because the speed of sound is decreasing and advance ratio increasing for the same indicated airspeed. These results suggest that existing measurement-based empirically derived helicopter rotor noise source models may give incorrect noise estimates when they are used at conditions where data were not measured and may need to be corrected for mission land-use planning purposes.

  12. Effects of vessel noise on underwater vocalizations of bottlenose dolphins, Tursiops truncatus, in the Sado Estuary

    OpenAIRE

    Sobreira, Filipa Alexandra Veiga

    2017-01-01

    Maritime traffic is an important source of disturbance for coastal cetaceans, especially for local and resident populations, like the bottlenose dolphins (Tursiops truncatus) population in the Sado estuary. Vessel noise might mask important signals such as communication calls. To compensate masking effects, animals may change their vocal behavior by shifting vocal rate, call intensity, call type, call frequency and duration. To evaluate the potential impacts on the acoustic behavior of this p...

  13. Ambient awareness: From random noise to digital closeness in online social networks.

    Science.gov (United States)

    Levordashka, Ana; Utz, Sonja

    2016-07-01

    Ambient awareness refers to the awareness social media users develop of their online network in result of being constantly exposed to social information, such as microblogging updates. Although each individual bit of information can seem like random noise, their incessant reception can amass to a coherent representation of social others. Despite its growing popularity and important implications for social media research, ambient awareness on public social media has not been studied empirically. We provide evidence for the occurrence of ambient awareness and examine key questions related to its content and functions. A diverse sample of participants reported experiencing awareness, both as a general feeling towards their network as a whole, and as knowledge of individual members of the network, whom they had not met in real life. Our results indicate that ambient awareness can develop peripherally, from fragmented information and in the relative absence of extensive one-to-one communication. We report the effects of demographics, media use, and network variables and discuss the implications of ambient awareness for relational and informational processes online.

  14. Acoustic inversion with self noise of an autonomous underwater vehicle to measure sound speed in marine sediments

    NARCIS (Netherlands)

    van Leijen, A.V.; Rothkranz, L.J.M.; Groen, F.C.A.

    2009-01-01

    This work reports on an experiment from the Maritime Rapid Environmental Assessment sea trials in 2007, where autonomous underwater vehicles were deployed for environmental assessment. Even though these underwater vehicles are very quiet platforms, this work investigates the potential of vehicle

  15. The preliminary results: Seismic ambient noise Rayleigh wave tomography around Merapi volcano, central Java, Indonesia

    International Nuclear Information System (INIS)

    Trichandi, Rahmantara; Yudistira, Tedi; Nugraha, Andri Dian; Zulhan, Zulfakriza; Saygin, Erdinc

    2015-01-01

    Ambient noise tomography is relatively a new method for imaging the shallow structure of the Earth subsurface. We presents the application of this method to produce a Rayleigh wave group velocity maps around the Merapi Volcano, Central Java. Rayleigh waves group velocity maps were reconstructed from the cross-correlation of ambient noise recorded by the DOMERAPI array which consists 43 broadband seismometers. In the processing stage, we first filtered the observation data to separatethe noise from the signal that dominated by the strong volcanic activities. Next, we cross-correlate the filtered data and stack to obtain the Green’s function for all possible station pairs. Then we carefully picked the peak of each Green’s function to estimate the dispersion trend and appliedMultiple Filter Technique to obtain the dispersion curve. Inter-station group velocity curvesare inverted to produceRayleigh wave group velocity maps for periods 1 to 10 s. The resulted Rayleigh group velocity maps show the interesting features around the Merapi Volcano which generally agree with the previous studies. Merapi-Lawu Anomaly (MLA) is emerged as a relatively low anomaly in our group velocity maps

  16. The preliminary results: Seismic ambient noise Rayleigh wave tomography around Merapi volcano, central Java, Indonesia

    Energy Technology Data Exchange (ETDEWEB)

    Trichandi, Rahmantara, E-mail: rachmantara.tri@gmail.com [Geophysical Engineering, Faculty of Mining and Petroleum Engineering, Institut Teknologi Bandung, 40132, Bandung (Indonesia); Yudistira, Tedi; Nugraha, Andri Dian [Global Geophysics Research Group, Faculty of Mining and Petroleum Engineering, Institut Teknologi Bandung, Bandung, 40132 (Indonesia); Zulhan, Zulfakriza [Earth Science Graduate Program, Faculty of Earth Science and Technology, Institut Teknologi Bandung, Bandung, 40132 (Indonesia); Saygin, Erdinc [Research School of Earth Sciences, The Australian National University, Canberra ACT 0200 (Australia)

    2015-04-24

    Ambient noise tomography is relatively a new method for imaging the shallow structure of the Earth subsurface. We presents the application of this method to produce a Rayleigh wave group velocity maps around the Merapi Volcano, Central Java. Rayleigh waves group velocity maps were reconstructed from the cross-correlation of ambient noise recorded by the DOMERAPI array which consists 43 broadband seismometers. In the processing stage, we first filtered the observation data to separatethe noise from the signal that dominated by the strong volcanic activities. Next, we cross-correlate the filtered data and stack to obtain the Green’s function for all possible station pairs. Then we carefully picked the peak of each Green’s function to estimate the dispersion trend and appliedMultiple Filter Technique to obtain the dispersion curve. Inter-station group velocity curvesare inverted to produceRayleigh wave group velocity maps for periods 1 to 10 s. The resulted Rayleigh group velocity maps show the interesting features around the Merapi Volcano which generally agree with the previous studies. Merapi-Lawu Anomaly (MLA) is emerged as a relatively low anomaly in our group velocity maps.

  17. Shear-wave velocity of marine sediments offshore Taiwan using ambient seismic noise

    Science.gov (United States)

    Lin, Yu-Tse; Lin, Jing-Yi; Kuo-Chen, Hao; Yeh, Yi-Chin; Cheng, Win-Bin

    2017-04-01

    Seismic ambient noise technology has many advantages over the traditional two-station method. The most important one is that noise is happening all the time and it can be widely and evenly distributed. Thus, the Green's Function of any station pair can be obtained through the data cross-correlation process. Many related studies have been performed to estimate the velocity structures based on the inland area. Only a few studies were reported for the marine area due to the relatively shorter recording time of ocean bottom seismometers (OBS) deployment and the high cost of the marine experiment. However, the understanding about the shear-wave velocity (Vs) of the marine sediments is very crucial for the hazard assessment related to submarine landslides, particularly with the growing of submarine resources exploration. In this study, we applied the ambient noise technique to four OBS seismic networks located offshore Taiwan in the aim of getting more information about the noise sources and having the preliminary estimation for the Vs of the marine sediments. Two of the seismic networks were deployed in the NE part of Taiwan, near the Ryukyu subduction system, whereas the others were in the SW area, on the continental margin rich in gas hydrate. Generally, ambient seismic noise could be associated with wind, ocean waves, rock fracturing and anthropogenic activity. In the southwestern Taiwan, the cross-correlation function obtained from two seismic networks indicate similar direction, suggestion that the source from the south part of the network could be the origin of the noise. However, the two networks in the northeastern Taiwan show various source direction, which could be caused by the abrupt change of bathymetry or the volcanic degassing effect frequently observed by the marine geophysical method in the area. The Vs determined from the dispersion curve shows a relatively higher value for the networks in the Okinawa Trough (OT) off NE Taiwan than that in the

  18. Effects of noise from non-traffic-related ambient sources on sleep: Review of the literature of 1990-2010

    Directory of Open Access Journals (Sweden)

    Sarah Omlin

    2011-01-01

    Full Text Available This article reviews the literature about the effects of specific non-traffic-related ambient noise sources on sleep that appeared in the last two decades. Although everybody is faced with noise of non-traffic and non-industry origin (e.g. sounds made by neighbors, talk, laughter, music, slamming doors, structural equipment, ventilation, heat pumps, noise from animals, barking dogs, outdoor events etc., little scientific knowledge exists about its effects on sleep. The findings of the present extensive literature search and review are as follows: Only a small number of surveys, laboratory and field studies about mainly neighborhood, leisure and animal noise have been carried out. Most of them indicate that ambient noise has some effect on human sleep. However, a quantitative meta-analysis and comparison is not possible due to the small number of studies available and at times large differences in quality.

  19. Deriving Deep Ocean Temperature Changes From the Ambient Acoustic Noise Field

    Science.gov (United States)

    Sambell, K.; Evers, L. G.; Snellen, M.

    2016-12-01

    Passively deriving the deep ocean temperature is a challenge. However, knowledge about changes in the deep ocean temperature are important in relation to climate change. In-situ observations are are and satellite observations are hardly applicable. Low-frequency sound waves of a few hertz can penetrate the deep oceans over long distances. As their propagation is temperature dependent, these waves contain valuable information that can be used for temperature monitoring. In this study, the use of interferometry is demonstrated by applying this technique to ambient noise measured at two hydrophone arrays located near Robinson Crusoe Island in the South Pacific Ocean. The arrays are separated by 40 km and are located at a depth of 800 m. Both arrays consist of three hydrophones with an interstation distance of 2 km. It is shown that the acoustic velocity, and with this the temperature variation, can be derived from measured hydro-acoustic data. Furthermore, the findings are supported by ocean models that describe the propagation of sound between the hydrophone arrays. This study shows the potential of using the ambient noise field for temperature monitoring in the deep ocean.

  20. Ambient Seismic Noise Tomography of a Loess High Bank at Dunaszekcső (Hungary)

    Science.gov (United States)

    Szanyi, Gyöngyvér; Gráczer, Zoltán; Győri, Erzsébet; Kaláb, Zdeněk; Lednická, Markéta

    2016-08-01

    Loess high banks along the right side of the Danube in Hungary are potential subjects of landslides. Small scale ambient seismic noise tomography was used at the Dunaszekcső high bank. The aim of the study was to map near surface velocity anomalies since we assume that the formation of tension cracks—which precede landslides—are represented by low velocities. Mapping Rayleigh wave group velocity distribution can help to image intact and creviced areas and identify the most vulnerable sections. The study area lies at the top of the Castle Hill of Dunaszekcső, which was named after Castellum Lugio, a fortress of Roman origin. The presently active head scarp was formed in April 2011, and our study area was chosen to be at its surroundings. Cross-correlation functions of ambient noise recordings were used to retrieve the dispersion curves, which served as the input of the group velocity tomography. Phase cross-correlation and time-frequency phase weighted stacking was applied to calculate the cross-correlation functions. The average Rayleigh wave group velocity at the loess high bank was found to be 171 ms^{-1}. The group velocity map at a 0.1 s period revealed a low-velocity region, whose location coincides with a highly creviced area, where slope failure takes place along a several meter wide territory. Another low velocity region was found, which might indicate a previously unknown loosened domain. The highest velocities were observed at the supposed remnants of Castellum Lugio.

  1. Uppermost mantle and crustal structure at Tristan da Cunha derived from ambient seismic noise

    Science.gov (United States)

    Ryberg, T.; Geissler, W. H.; Jokat, W.; Pandey, S.

    2017-08-01

    According to classical plume theory, the Tristan da Cunha hotspot, located ∼400 km east off the Mid-Atlantic Ridge, is thought to have played a major role in the rifting while creating an aseismic Walvis Ridge during and after the breakup of the South Atlantic margins. Volcanic activity on the Tristan da Cunha Island shows that the hotspot might still be there influencing the upper mantle and crustal structure. In this study we present ambient noise data from 24 broadband OBS around Tristan da Cunha and a seismic station on Nightingale Island, which provide first constraints on the crustal and uppermost mantle structure around the island. By combining ambient noise techniques, dispersion curve analysis of Rayleigh waves, 2D tomographic inversion of travel times and 3D depth inversion of dispersion data we derived a 3D VS velocity model around the archipelago of Tristan da Cunha. The model shows an isolated, vertically sharp bounded thickened and modified crust beneath the islands surrounded by thin oceanic crust (feeding system/magmatic underplating, respectively. The observed simple and localized volcanic structure, embedded in a rather homogeneous crust and upper mantle indicates only minor and very localized magmatic overprinting of the existing lithosphere by the Tristan da Cunha hotspot. The uppermost mantle S wave velocity beneath nearby seamounts and to the SW of the islands is also slow and could indicate a thermal influence from a deeper source, whereas the Tristan da Cunha Fracture Zone shows no signs of modification.

  2. On the effect of topography on short-period ambient noise tomography

    Science.gov (United States)

    Köhler, A.; Weidle, C.; Maupin, V.

    2012-04-01

    Due to the increasing popularity of using empirical Green's functions obtained from ambient seismic noise, more and more regional tomographical studies based on short-periods surface waves are published. Results could potentially be biased in mountainous regions where topography is not small compared to the wavelength and penetration depth of the considered waves. We investigate the effect of topography on the propagation of short-period (3-10 seconds) Rayleigh waves empirically by means of synthetic data using a spectral element code and a 3-D model with real topography. We show that topography along a profile through the studied area can result in an underestimation of phase velocities of up to about 0.7% at the shortest investigated period (3 seconds). Contrary to the expectation that this bias results from the increased surface distance along topography, we find that this error can be estimated by local topographic contrasts in the vicinity of the receiver alone. We discuss and generalize our results by considering topographic profiles through other mountain ranges and find that southern Norway is a good proxy to assess the topography effect. Nevertheless, topographic bias on phase velocity measurements is in general not large enough to produce a significant effect on ambient noise tomographies.

  3. On the effect of topography on surface wave propagation in the ambient noise frequency range

    Science.gov (United States)

    Köhler, Andreas; Weidle, Christian; Maupin, Valérie

    2012-04-01

    Due to the increasing popularity of analyzing empirical Green's functions obtained from ambient seismic noise, more and more regional tomographical studies based on short-period surface waves are published. Results could potentially be biased in mountainous regions where topography is not small compared to the wavelength and penetration depth of the considered waves. We investigate the effect of topography on the propagation of short-period Rayleigh waves empirically by means of synthetic data using a spectral element code and a 3-D model with real topography. We show that topography along a profile through the studied area can result in an underestimation of phase velocities of up to about 0.7% at the shortest investigated period (3 s). Contrary to the expectation that this bias results from the increased surface distance along topography, we find that this error can be estimated by local topographic contrasts in the vicinity of the receiver alone. We discuss and generalize our results by considering topographic profiles through other mountain ranges and find that southern Norway is a good proxy to assess the topography effect. Nevertheless, topographic bias on phase velocity measurements is in general not large enough to significantly affect recovered velocity variations in the ambient noise frequency range.

  4. Potential of ambient seismic noise techniques to monitor the St. Gallen geothermal site (Switzerland)

    Science.gov (United States)

    Obermann, A.; Kraft, T.; Larose, E.; Wiemer, S.

    2015-06-01

    The failures of two recent deep geothermal energy projects in Switzerland (Basel, 2006; St. Gallen, 2013) have again highlighted that one of the key challenges for the successful development and operation of deep underground heat exchangers is to control the risk of inducing potentially hazardous seismic events. In St. Gallen, after an injection test and two acid injections that were accompanied by a small number of micro-earthquakes (MLkick). The "killing" procedures that had to be initiated following standard drilling procedures led to a ML3.5 earthquake. With ambient seismic noise cross correlations from nine stations, we observe a significant loss of waveform coherence that we can horizontally and vertically constrain to the injection location of the fluid. The loss of waveform coherence starts with the onset of the fluid injections 4 days prior to the gas kick. We interpret the loss of coherence as a local perturbation of the medium. We show how ambient seismic noise analysis can be used to assess the aseismic response of the subsurface to geomechanical well operations and how this method could have helped to recognize the unexpected reservoir dynamics at an earlier stage than the microseismic response alone, allowed.

  5. Potential of ambient seismic noise techniques to monitor injection induced subsurface changes

    Science.gov (United States)

    Obermann, A.; Kraft, T.; Wiemer, S.

    2015-12-01

    The failures of two recent deep geothermal energy projects in Switzerland (Basel, 2006; St. Gallen, 2013) have again highlighted that one of the key challenges for the successful development and operation of deep underground heat exchangers is to control the risk of inducing potentially hazardous seismic events. In St. Gallen, after an injection test and two acid injections that were accompanied by a small number of micro-earthquakes (ML kick). The "killing" procedures that had to be initiated following standard drilling procedures led to a ML3.5 earthquake. With ambient seismic noise cross correlations from nine stations, we observe a significant loss of waveform coherence that we can horizontally and vertically constrain to the injection location of the fluid. The loss of waveform coherence starts with the onset of the fluid injections 4 days prior to the gas kick. We interpret the loss of coherence as a local perturbation of the medium. We show how ambient seismic noise analysis can be used to assess the aseismic response of the subsurface to geomechanical well operations and how this method could have helped to recognize the unexpected reservoir dynamics at an earlier stage than the microseismic response alone, allowed.

  6. Spatial Vertical Directionality and Correlation of Low-Frequency Ambient Noise in Deep Ocean Direct-Arrival Zones

    Directory of Open Access Journals (Sweden)

    Qiulong Yang

    2018-01-01

    Full Text Available Wind-driven and distant shipping noise sources contribute to the total noise field in the deep ocean direct-arrival zones. Wind-driven and distant shipping noise sources may significantly and simultaneously affect the spatial characteristics of the total noise field to some extent. In this work, a ray approach and parabolic equation solution method were jointly utilized to model the low-frequency ambient noise field in a range-dependent deep ocean environment by considering their calculation accuracy and efficiency in near-field wind-driven and far-field distant shipping noise fields. The reanalysis databases of National Center of Environment Prediction (NCEP and Volunteer Observation System (VOS were used to model the ambient noise source intensity and distribution. Spatial vertical directionality and correlation were analyzed in three scenarios that correspond to three wind speed conditions. The noise field was dominated by distant shipping noise sources when the wind speed was less than 3 m/s, and then the spatial vertical directionality and vertical correlation of the total noise field were nearly consistent with those of distant shipping noise field. The total noise field was completely dominated by near field wind generated noise sources when the wind speed was greater than 12 m/s at 150 Hz, and then the spatial vertical correlation coefficient and directionality pattern of the total noise field was approximately consistent with that of the wind-driven noise field. The spatial characteristics of the total noise field for wind speeds between 3 m/s and 12 m/s were the weighted results of wind-driven and distant shipping noise fields. Furthermore, the spatial characteristics of low-frequency ambient noise field were compared with the classical Cron/Sherman deep water noise field coherence function. Simulation results with the described modeling method showed good agreement with the experimental measurement results based on the vertical line

  7. Reducing Risk of Noise-Induced Hearing Loss in Collegiate Music Ensembles Using Ambient Technology.

    Science.gov (United States)

    Powell, Jason; Chesky, Kris

    2017-09-01

    Student musicians are at risk for noise-induced hearing loss (NIHL) as they develop skills and perform during instructional activities. Studies using longitudinal dosimeter data show that pedagogical procedures and instructor behaviors are highly predictive of NIHL risk, thus implying the need for innovative approaches to increase instructor competency in managing instructional activities without interfering with artistic and academic freedom. Ambient information systems, an emerging trend in human-computer interaction that infuses psychological behavioral theories into technologies, can help construct informative risk-regulating systems. The purpose of this study was to determine the effects of introducing an ambient information system into the ensemble setting. The system used two ambient displays and a counterbalanced within-subjects treatment study design with six jazz ensemble instructors to determine if the system could induce a behavior change that alters trends in measures resulting from dosimeter data. This study assessed efficacy using time series analysis to determine changes in eight statistical measures of behavior over a 9-wk period. Analysis showed that the system was effective, as all instructors showed changes in a combination of measures. This study is in an important step in developing non-interfering technology to reduce NIHL among academic musicians.

  8. Ambient noise as the new source for urban engineering seismology and earthquake engineering: a case study from Beijing metropolitan area

    Science.gov (United States)

    Liu, Lanbo; Chen, Qi-fu; Wang, Weijun; Rohrbach, Eric

    2014-02-01

    In highly populated urban centers, traditional seismic survey sources can no longer be properly applied due to restrictions in modern civilian life styles. The ambient vibration noise, including both microseisms and microtremor, though are generally weak but available anywhere and anytime, can be an ideal supplementary source for conducting seismic surveys for engineering seismology and earthquake engineering. This is fundamentally supported by advanced digital signal processing techniques for effectively extracting the useful information out from the noise. Thus, it can be essentially regarded as a passive seismic method. In this paper we first make a brief survey of the ambient vibration noise, followed by a quick summary of digital signal processing for passive seismic surveys. Then the applications of ambient noise in engineering seismology and earthquake engineering for urban settings are illustrated with examples from Beijing metropolitan area. For engineering seismology the example is the assessment of site effect in a large area via microtremor observations. For earthquake engineering the example is for structural characterization of a typical reinforced concrete high-rise building using background vibration noise. By showing these examples we argue that the ambient noise can be treated as a new source that is economical, practical, and particularly valuable to engineering seismology and earthquake engineering projects for seismic hazard mitigation in urban areas.

  9. Rayleigh wave group-velocity across the Dominican Republic and Puerto Rico from ambient noise tomography

    Science.gov (United States)

    Quiros, D.; Pulliam, J.; Polanco Rivera, E.; Huerfano Moreno, V. A.

    2017-12-01

    The eastern North America-Caribbean (NA-CAR) plate boundary near the islands of Hispaniola (which is comprised of the Dominican Republic and Haiti) and Puerto Rico is a complex transition zone in which strain is accommodated by two transform fault systems and oblique subduction. In 2013, scientists from Baylor University, the Autonomous University of Santo Domingo, and the Puerto Rico Seismic Network deployed 16 broadband stations on the Dominican Republic to expand the local permanent network. The goal of the Greater Antilles Seismic Program (GrASP) is to combine its data with that from permanent networks in Puerto Rico, Haiti, Cuba, the Cayman Islands, and Jamaica to develop a better understanding of the crust and upper mantle structure in the Northeastern Caribbean (Greater Antilles). One important goal of GrASP is to develop robust velocity models that can be used to improve earthquake location and seismic hazard efforts. In this study, we focus on obtaining Rayleigh wave group velocity maps from ambient noise tomography. By cross-correlating ambient seismic noise recorded at 53 stations between 2010 to present, we obtain Green's functions between 1165 pairs of stations. From these, we obtain dispersion curves by the application of FTAN methods with phase-matched filtering. Selection criteria depend on the signal-to-noise ratio and seasonal variability, with further filtering done by rejecting velocities incompatible with maps produced from overdamped tomographic inversions. Preliminary dispersion maps show strong correlations with large-scale geological and tectonic features for periods between 5 - 20 s, such as the Cordillera Central in both the Dominican Republic and Puerto Rico, the Mona Passage, and the NA-CAR subduction zone. Ongoing efforts focus on including shorter periods in Puerto Rico as its denser station distribution could allow us to retrieve higher resolution group velocity maps.

  10. Retrieval of Body-Wave Reflections Using Ambient Noise Interferometry Using a Small-Scale Experiment

    Science.gov (United States)

    Dantas, Odmaksuel Anísio Bezerra; do Nascimento, Aderson Farias; Schimmel, Martin

    2018-02-01

    We report the retrieval of body-wave reflections from noise records using a small-scale experiment over a mature oil field. The reflections are obtained by cross-correlation and stacking of the data. We used the stacked correlograms to create virtual source-to-receiver common shot gathers and are able to obtain body-wave reflections. Surface waves that obliterate the body-waves in our noise correlations were attenuated following a standard procedure from active source seismics. Further different strategies were employed to cross-correlate and stack the data: classical geometrical normalized cross-correlation (CCGN), phase cross-correlation (PCC), linear stacking**** and phase weighted stacking (PWS). PCC and PWS are based on the instantaneous phase coherence of analytic signals. The four approaches are independent and reveal the reflections; nevertheless, the combination of PWS and CCGN provided the best results. Our analysis is based on 2145 cross-correlations of 600 s data segments. We also compare the resulted virtual shot gathers with an active 2D seismic line near the passive experiment. It is shown that our ambient noise analysis reproduces reflections which are present in the active seismic data.

  11. Characterization of site-effects in the urban area of Canakkale, Turkey, using ambient noise measurements

    Science.gov (United States)

    Demirci, Alper; Bekler, Tolga; Karagöz, Özlem

    2010-05-01

    The local site conditions can cause variations in the ground motion during the earthquake events. These local effects can be estimated by Nakamura method (1989) which is based on the analysis and treatment of earth vibration records by calculating the ratio of horizontal spectrum to vertical spectrum (H/V). This approach uses ambient noises and aids to estimate the dynamic soil conditions like fundamental vibration period and soil amplification of the surface layers, to characterize the seismic hazard during earthquakes and to provide detailed information for seismic microzonation in small scale urban areas. Due to these advantages, the method has been frequently used by a great number of seismologists and engineers. In this study, we aimed at explaining the soil conditions in Çanakkale and Kepez basins by using H/V technique. Çanakkale and Kepez (NW, Turkey) have fairly complex tectonic structure and have been exposed to serious earthquake damages in historical and instrumental period. Active faults, which have influence on the Çanakkale and Kepez settlements, are the Yenice-Gönen fault, Saroz-Gaziköy fault and Etili fault. It is well known that, these faults have produced high magnitude earthquakes such as 7.2 in 1912 and 7.3 in 1953. The surface geology of the surveyed area is covered by quaternary aged sediments. Sarıçay river, which originates from the eastern hilly area, accumulates sediment deposits and forms this alluvial basin. Considering the geological conditions, ambient noises were recorded at 88 measurement points which were selected to provide good coverage of the study area. All records were acquired during the midnight (between 1:00 am and 6:00 am) to reduce the artificial effects in the urban area. Taking into account the effects of undesirable traffic and industrial noises in the vicinity of measurements stations, record lengths were chosen in the range of 25-75 minutes with the sampling rate of 100 Hz. Once the required signal processes

  12. Seismic tomography and ambient noise reflection interferometry on Reykjanes, SW Iceland

    Science.gov (United States)

    Jousset, Philippe; Verdel, Arie; Ágústsson, Kristján; Blanck, Hanna; Franke, Steven; Metz, Malte; Ryberg, Trond; Weemstra, Cornelius; Hersir, Gylfi; Bruhn, David

    2016-04-01

    Recent advances in volcano-seismology and seismic noise interferometry have introduced new processing techniques for assessing subsurface structures and controls on fluid flow in geothermal systems. We present tomographic results obtained from seismic data recorded around geothermal reservoirs located both on-land Reykjanes, SW-Iceland and offshore along Reykjanes Ridge. We gathered records from a network of 234 seismic stations (including 24 Ocean Bottom Seismometers) deployed between April 2014 and August 2015. In order to determine the orientation of the OBS stations, we used Rayleigh waves planar particle motions from large magnitude earthquakes. This method proved suitable using the on-land stations: orientations determined using this method with the orientations measured using a giro-compass agreed. We obtain 3D velocity images from two fundamentally different tomography methods. First, we used local earthquakes to perform travel time tomography. The processing includes first arrival picking of P- and S- phases using an automatic detection and picking technique based on Akaike Information Criteria. We locate earthquakes by using a non-linear localization technique, as a priori information for deriving a 1D velocity model. We then computed 3D velocity models of velocities by joint inversion of each earthquake's location and lateral velocity anomalies with respect to the 1D model. Our models confirms previous models obtained in the area, with enhanced details. Second, we performed ambient noise cross-correlation techniques in order to derive an S velocity model, especially where earthquakes did not occur. Cross-correlation techniques involve the computation of cross- correlation between seismic records, from which Green's functions are estimated. Surface wave inversion of the Green's functions allows derivation of an S wave velocity model. Noise correlation theory furthermore shows that zero-offset P-wave reflectivity at selected station locations can be

  13. Association between ambient noise exposure, hearing acuity, and risk of acute occupational injury.

    Science.gov (United States)

    Cantley, Linda F; Galusha, Deron; Cullen, Mark R; Dixon-Ernst, Christine; Rabinowitz, Peter M; Neitzel, Richard L

    2015-01-01

    This study aimed to examine the associations between acute workplace injury risk, ambient noise exposure, and hearing acuity, adjusting for reported hearing protection use. In a cohort of 9220 aluminum manufacturing workers studied over six years (33 300 person-years, 13 323 person-jobs), multivariate mixed effects models were used to estimate relative risk (RR) of all injuries as well as serious injuries by noise exposure category and hearing threshold level (HTL) adjusting for recognized and potential confounders. Compared to noise exposure was associated with elevated risk in a monotonic and statistically significant exposure-response pattern for all injuries and serious injuries with higher risk estimates observed for serious injuries [82-84.99 dBA: RR 1.26, 95% confidence interval (95% CI) 0.96-1.64; 85-87.99 dBA: RR 1.39, 95% CI 1.05-1.85; ≥88 dBA: RR 2.29, 95% CI 1.52-3.47]. Hearing loss was associated with increased risk for all injuries, but was not a significant predictor of risk for the subset of more serious injuries. Compared to those without hearing loss, workers with HTL ≥25 dB had 21% increased all injury risk (RR 1.21, 95% CI 1.09-1.33) while those with HTL 10-24.99 dB had 6% increased risk (RR 1.06, 95% CI 1.00-1.13). Reported hearing protection type did not predict injury risk. Noise exposure levels as low as 85 dBA may increase workplace injury risk. HTL was associated with increased risk for all, but not the subset of serious, injuries. Additional study is needed both to confirm the observed associations and explore causal pathways.

  14. 3D shear wave velocity structure revealed with ambient noise tomography on a DAS array

    Science.gov (United States)

    Zeng, X.; Thurber, C. H.; Wang, H. F.; Fratta, D.

    2017-12-01

    An 8700-m Distributed Acoustic Sensing (DAS) cable was deployed at Brady's Hot Springs, Nevada in March 2016 in a 1.5 by 0.5 km study area. The layout of the DAS array was designed with a zig-zag geometry to obtain relatively uniform areal and varied angular coverage, providing very dense coverage with a one-meter channel spacing. This array continuously recorded signals of a vibroseis truck, earthquakes, and traffic noise during the 15-day deployment. As shown in a previous study (Zeng et al., 2017), ambient noise tomography can be applied to DAS continuous records to image shear wave velocity structure in the near surface. To avoid effects of the vibroseis truck operation, only continuous data recorded during the nighttime was used to compute noise cross-correlation functions for channel pairs within a given linear segment. The frequency band of whitening was set at 5 to 15 Hz and the length of the cross-correlation time window was set to 60 second. The phase velocities were determined using the multichannel analysis of surface waves (MASW) methodology. The phase velocity dispersion curve was then used to invert for shear wave velocity profiles. A preliminarily velocity model at Brady's Hot Springs (Lawrence Livermore National Laboratory, 2015) was used as the starting model and the sensitivity kernels of Rayleigh wave group and phase velocities were computed with this model. As the sensitivity kernel shows, shear wave velocity in the top 200 m can be constrained with Rayleigh wave group and phase velocities in our frequency band. With the picked phase velocity data, the shear wave velocity structure can be obtained via Occam's inversion (Constable et al., 1987; Lai 1998). Shear wave velocity gradually increases with depth and it is generally faster than the Lawrence Livermore National Laboratory (2015) model. Furthermore, that model has limiting constraints at shallow depth. The strong spatial variation is interpreted to reflect the different sediments and

  15. Magmatism on rift flanks: Insights from ambient noise phase velocity in Afar region

    Science.gov (United States)

    Korostelev, Félicie; Weemstra, Cornelis; Leroy, Sylvie; Boschi, Lapo; Keir, Derek; Ren, Yong; Molinari, Irene; Ahmed, Abdulhakim; Stuart, Graham W.; Rolandone, Frédérique; Khanbari, Khaled; Hammond, James O. S.; Kendall, J. M.; Doubre, Cécile; Ganad, Ismail Al; Goitom, Berhe; Ayele, Atalay

    2015-04-01

    During the breakup of continents in magmatic settings, the extension of the rift valley is commonly assumed to initially occur by border faulting and progressively migrate in space and time toward the spreading axis. Magmatic processes near the rift flanks are commonly ignored. We present phase velocity maps of the crust and uppermost mantle of the conjugate margins of the southern Red Sea (Afar and Yemen) using ambient noise tomography to constrain crustal modification during breakup. Our images show that the low seismic velocities characterize not only the upper crust beneath the axial volcanic systems but also both upper and lower crust beneath the rift flanks where ongoing volcanism and hydrothermal activity occur at the surface. Magmatic modification of the crust beneath rift flanks likely occurs for a protracted period of time during the breakup process and may persist through to early seafloor spreading.

  16. MSNoise: a Python Package for Monitoring Seismic Velocity Changes using Ambient Seismic Noise

    Science.gov (United States)

    Lecocq, Thomas; Caudron, Corentin; Brenguier, Florent

    2014-05-01

    We present MSNoise, a complete software suite to compute relative seismic velocity changes under a seismic network, using ambient seismic noise. The whole is written in Python, from the monitoring of data archives, to the production of high quality figures. All steps have been optimized to only compute the necessary steps and to use 'job'-based processing. All steps can be changed by matching the in/outs. MSNoise exposes an API for communication with the data archive and the database. We present a validation of the software on a dataset acquired during the UnderVolc project on the Piton de la Fournaise Volcano, La Réunion Island, France, for which precursory relative changes of seismic velocity are visible for three eruptions betwee 2009 and 2011. MSNoise is available on http://www.msnoise.org

  17. Rayleigh wave tomography of the British Isles from ambient seismic noise

    Science.gov (United States)

    Nicolson, Heather; Curtis, Andrew; Baptie, Brian

    2014-08-01

    We present the first Rayleigh wave group speed maps of the British Isles constructed from ambient seismic noise. The maps also constitute the first surface wave tomography study of the crust under the British Isles at a relatively high resolution. We computed interferometric, interstation Rayleigh waves from vertical component records of ambient seismic noise recorded on 63 broad-band and short-period stations across the UK and Ireland. Group velocity measurements were made from the resulting surface wave dispersion curves between 5 and 25 s using a multiple phase-matched filter method. Uncertainties in the group velocities were computed by calculating the standard deviation of four dispersion curves constructed by stacking a random selection of daily cross-correlations. Where an uncertainty could not be obtained for a ray path using this method, we estimated it as a function of the interreceiver distance. Group velocity maps were computed for 5-25-s period using the Fast Marching forward solution of the eikonal equation and iterative, linearized inversion. At short and intermediate periods, the maps show remarkable agreement with the major geological features of the British Isles including: terrane boundaries in Scotland; regions of late Palaeozoic basement uplift; areas of exposed late Proterozoic/early Palaeozoic rocks in southwest Scotland, northern England and northwest Wales and, sedimentary basins formed during the Mesozoic such as the Irish Sea Basin, the Chester Basin, the Worcester Graben and the Wessex Basin. The maps also show a consistent low-velocity anomaly in the region of the Midlands Platform, a Proterozoic crustal block in the English Midlands. At longer periods, which are sensitive velocities in the lower crustal/upper mantle, the maps suggest that the depth of Moho beneath the British Isles decreases towards the north and west. Areas of fast velocity in the lower crust also coincide with areas thought to be associated with underplating of the

  18. 3D basin structure of the Santa Clara Valley constrained by ambient noise tomography

    Science.gov (United States)

    Cho, H.; Lee, S. J.; Rhie, J.; Kim, S.

    2017-12-01

    The basin structure is an important factor controls the intensity and duration of ground shaking due to earthquake. Thus it is important to study the basin structure for better understanding seismic hazard and also improving the earthquake preparedness. An active source seismic survey is the most appropriate method to determine the basin structure in detail but its applicability, especially in urban areas, is limited. In this study, we tested the potential of an ambient noise tomography, which can be a cheaper and more easily applicable method compared to a traditional active source survey, to construct the velocity model of the basin. Our testing region is the Santa Clara Valley, which is one of the major urban sedimentary basins in the States. We selected this region because continuous seismic recordings and well defined velocity models are available. Continuous seismic recordings of 6 months from short-period array of Santa Clara Valley Seismic Experiment are cross-correlated with 1 hour time window. And the fast marching method and the subspace method are jointly applied to construct 2-D group velocity maps between 0.2 - 4.0 Hz. Then, shear wave velocity model of the Santa Clara Valley is calculated up to 5 km depth using bayesian inversion technique. Although our model cannot depict the detailed structures, it is roughly comparable with the velocity model of the US Geological Survey, which is constrained by active seismic surveys and field researches. This result indicate that an ambient noise tomography can be a replacement, at least in part, of an active seismic survey to construct the velocity model of the basin.

  19. Subsurface Characterization Beneath the Coso Geothermal Field by Ambient Noise Tomography

    Science.gov (United States)

    Ritzwoller, M. H.; Yang, Y.; Levshin, A. L.; Barmin, M. P.; Jones, C. H.

    2009-12-01

    The Coso Geothermal Area has been the subject of numerous geophysical studies over the past 30 years. Various seismological techniques have been applied to evaluate the regional stress distribution, velocity and attenuation structure of the subsurface. None of these studies has imaged subsurface shear velocity using surface waves generated either by local micro-earthquakes or by regional or teleseismic earthquakes, nor have any used interferometric methods based on ambient noise. In this study, we apply an interferometic method based on ambient seismic noise aimed at imaging the shallow shear velocity structure beneath the Coso Geothermal Area. Data are from a PASSCAL experiment deployed between 1998 and 2000 and regional broad-band seismometers operated by CalTech. Cross-correlations are performed between each pair of the COSO PASSCAL and CalTech stations for 15 months from March 1999 to May 2000. After compensating for or correcting instrumental irregularities and selecting reliable Rayleigh wave dispersion measurements from the inter-station cross-correlations, we obtain about 300 measurement paths as the basis for surface wave tomography at periods from 3 to 10 sec. Uncertainties of both group and phase velocity measurements are estimated using the variations among the dispersion curves from one-month cross-correlations in different months. The resulting dispersion maps reveal low group and phase velocities in the COSO volcanic field, especially at 3 sec period for group velocities, and high velocities to the east of the COSO volcanic field. The velocity variations are consistent with surface geological features, which encourages future inversion for 3-D shear velocity structure in the top 15 km of the crust.

  20. Full-Wave Ambient Noise Tomography of the Long Valley Volcanic Region (California)

    Science.gov (United States)

    Flinders, A. F.; Shelly, D. R.; Dawson, P. B.; Hill, D. P.; Shen, Y.

    2017-12-01

    In the late 1970s, and throughout the 1990s, Long Valley Caldera (California) experienced intense periods of unrest characterized by uplift of the resurgent dome, earthquake swarms, and CO2 emissions around Mammoth Mountain. While modeling of the uplift and gravity changes support the possibility of new magmatic intrusions beneath the caldera, geologic interpretations conclude that the magmatic system underlying the caldera is moribund. Geophysical studies yield diverse versions of a sizable but poorly resolved low-velocity zone at depth (> 6km), yet whether this zone is indicative of a significant volume of crystal mush, smaller isolated pockets of partial melt, or magmatic fluids, is inconclusive. The nature of this low-velocity zone, and the state of volcano's magmatic system, carry important implications for the significance of resurgent-dome inflation and the nature of associated hazards. To better characterize this low-velocity zone we present preliminary results from a 3D full-waveform ambient-noise seismic tomography model derived from the past 25 years of vertical component broadband and short-period seismic data. This new study uses fully numerical solutions of the wave equation to account for the complex wave propagation in a heterogeneous, 3D earth model, including wave interaction with topography. The method ensures that wave propagation is modeled accurately in 3D, enabling the full use of seismic records. By using empirical Green's functions, derived from ambient noise and modeled as Rayleigh surface waves, we are able to extend model resolution to depths beyond the limits of previous local earthquake studies. The model encompasses not only the Long Valley Caldera, but the entire Long Valley Volcanic Region, including Mammoth Mountain and the Mono Crater/Inyo Domes volcanic chain.

  1. Investigating Near Surface S-Wave Velocity Properties Using Ambient Noise in Southwestern Taiwan

    Directory of Open Access Journals (Sweden)

    Chun-Hsiang Kuo

    2015-01-01

    Full Text Available Ambient noise is typically used to estimate seismic site effects and velocity profiles instead of earthquake recordings, especially in areas with limited seismic data. The dominant Horizontal to Vertical Spectral Ratio (HVSR frequency of ambient noise is correlated to Vs30, which is the average S-wave velocity in the top 30 m. Vs30 is a widely used parameter for defining seismic amplification in earthquake engineering. HVSR can detect the vertical discontinuity of velocities, that is, the interfaces between hard bedrock and soft sediments. In southwestern Taiwan most strong motion stations are located in the plains and show a dominant frequency lower than 3 Hz. Several stations near the coast have low dominant frequencies of less than 1 Hz. The dominant frequencies are higher than 4 Hz at piedmont stations. The stations in the mountains with dominant frequencies over 8 Hz are typically located on very hard sites. This study analyzed the HVSR characteristics under different seismic site conditions considering the Vs30 from previous study (Kuo et al. 2012. The result implies that HVSRs are a better tool than Vs30 to classify the sites where bedrock is deeper than 30 m. Furthermore, we found a linear correlation between Vs30 and dominant HVSR frequency which could be used as a proxy of Vs30. The Vs30 map in this area was derived using the Engineering Geological Database for Taiwan Strong Motion Instrumentation Program (EGDT. The comparable distribution pattern between the dominant frequency and Vs30 demonstrate that HVSR can recognize S-wave velocity properties at the shallow subsurface.

  2. Environmental Resources of Selected Areas of Hawaii: Climate, Ambient Air Quality, and Noise (DRAFT)

    Energy Technology Data Exchange (ETDEWEB)

    Lombardi, D.A.; Blasing, T.J.; Easterly, C.E.; Hamilton, C.B.

    1994-06-01

    This report has been prepared to make available and archive background scientific data and related information on climate, ambient air quality, and ambient noise levels collected during the preparation of the environmental impact statement (EIS) for Phases 3 and 4 of the Hawaii Geothermal Project (HGP) as defined by the state of hawaii in its April 1989 proposal to Congress. The US Department of Energy (DOE) published a notice in the Federal Register on May 17, 1994 withdrawing its Notice of Intent of February 14, 1992, to prepare the HGP-EIS. Since the state of Hawaii is no longer pursuing or planning to pursue the HGP, DOE considers the project to be terminated. The report presents a general description of the climate and air quality for the islands of Hawaii (henceforth referred to as Hawaii), Maui, and Oahu. It also presents a literature review as baseline information on the health effects of hydrogen sulfide. the scientific background data and related information is being made available for use by others in conducting future scientific research in these areas. This report describes the environmental resources present in the areas studied (i.e., the affected environment) and does not represent an assessment of environmental impacts.

  3. Environmental resources of selected areas of Hawaii: Climate, ambient air quality, and noise

    Energy Technology Data Exchange (ETDEWEB)

    Lombardi, D.A.; Blasing, T.J.; Easterly, C.E.; Reed, R.M. [Oak Ridge National Lab., TN (United States); Hamilton, C.B. [Univ. of Tennessee, Knoxville, TN (United States)

    1995-03-01

    This report has been prepared to make available and archive background scientific data and related information on climate, ambient air quality, and ambient noise levels collected during the preparation of the environmental impact statement (EIS) for Phases 3 and 4 of the Hawaii Geothermal Project (HGP) as defined by the state of Hawaii in its April 1989 proposal to Congress. The US Department of Energy (DOE) published a notice withdrawing its Notice of Intent to prepare the HGP-EIS. Since the state of Hawaii is no longer pursuing or planning to pursue the HGP, DOE considers the project to be terminated. The report presents a general description of the climate add air quality for the islands of Hawaii (henceforth referred to as Hawaii), Maui and Oahu. It also presents a literature review as baseline information on the health effects of sulfide. The scientific background data and related information is being made available for use by others in conducting future scientific research in these areas. This report describes the environmental resources present in the areas studied (i.e., the affected environment) and does not represent an assessment of environmental impacts.

  4. Imaging of upper crustal structure beneath East Java-Bali, Indonesia with ambient noise tomography

    Science.gov (United States)

    Martha, Agustya Adi; Cummins, Phil; Saygin, Erdinc; Sri Widiyantoro; Masturyono

    2017-12-01

    The complex geological structures in East Java and Bali provide important opportunities for natural resource exploitation, but also harbor perils associated with natural disasters. Such a condition makes the East Java region an important area for exploration of the subsurface seismic wave velocity structure, especially in its upper crust. We employed the ambient noise tomography method to image the upper crustal structure under this study area. We used seismic data recorded at 24 seismographs of BMKG spread over East Java and Bali. In addition, we installed 28 portable seismographs in East Java from April 2013 to January 2014 for 2-8 weeks, and we installed an additional 28 seismographs simultaneously throughout East Java from August 2015 to April 2016. We constructed inter-station Rayleigh wave Green's functions through cross-correlations of the vertical component of seismic noise recordings at 1500 pairs of stations. We used the Neighborhood Algorithm to construct depth profiles of shear wave velocity (Vs). The main result obtained from this study is the thickness of sediment cover. East Java's southern mountain zone is dominated by higher Vs, the Kendeng basin in the center is dominated by very low Vs, and the Rembang zone (to the North of Kendeng zone) is associated with medium Vs. The existence of structures with oil and gas potential in the Kendeng and Rembang zones can be identified by low Vs.

  5. Monitoring transient changes within overpressured regions of subduction zones using ambient seismic noise.

    Science.gov (United States)

    Chaves, Esteban J; Schwartz, Susan Y

    2016-01-01

    In subduction zones, elevated pore fluid pressure, generally linked to metamorphic dehydration reactions, has a profound influence on the mechanical behavior of the plate interface and forearc crust through its control on effective stress. We use seismic noise-based monitoring to characterize seismic velocity variations following the 2012 Nicoya Peninsula, Costa Rica earthquake [M w (moment magnitude) 7.6] that we attribute to the presence of pressurized pore fluids. Our study reveals a strong velocity reduction (~0.6%) in a region where previous work identified high forearc pore fluid pressure. The depth of this velocity reduction is constrained to be below 5 km and therefore not the result of near-surface damage due to strong ground motions; rather, we posit that it is caused by fracturing of the fluid-pressurized weakened crust due to dynamic stresses. Although pressurized fluids have been implicated in causing coseismic velocity reductions beneath the Japanese volcanic arc, this is the first report of a similar phenomenon in a subduction zone setting. It demonstrates the potential to identify pressurized fluids in subduction zones using temporal variations of seismic velocity inferred from ambient seismic noise correlations.

  6. Ambient noise tomography across Mount St. Helens using a dense seismic array

    KAUST Repository

    Wang, Yadong

    2017-05-08

    We investigated upper crustal structure with data from a dense seismic array deployed around Mount St. Helens for 2 weeks in the summer of 2014. Interstation cross correlations of ambient seismic noise data from the array were obtained, and clear fundamental mode Rayleigh waves were observed between 2.5 and 5 s periods. In addition, higher-mode signals were observed around 2 s period. Frequency-time analysis was applied to measure fundamental mode Rayleigh wave phase velocities, which were used to invert for 2-D phase velocity maps. An azimuth-dependent traveltime correction was implemented to mitigate potential biases introduced due to an inhomogeneous noise source distribution. Reliable phase velocity maps were only obtained between 3 and 4 s periods due to limitations imposed by the array aperture and higher-mode contamination. The phase velocity tomography results, which are sensitive to structure shallower than 6 km depth, reveal an ~10–15% low-velocity anomaly centered beneath the volcanic edifice and peripheral high-velocity anomalies that likely correspond to cooled igneous intrusions. We suggest that the low-velocity anomaly reflects the high-porosity mixture of lava and ash deposits near the surface of the edifice, a highly fractured magmatic conduit and hydrothermal system beneath the volcano, and possibly a small contribution from silicate melt.

  7. Direct ambient noise tomography for 3-D near surface shear velocity structure: methodology and applications

    Science.gov (United States)

    Yao, H.; Fang, H.; Li, C.; Liu, Y.; Zhang, H.; van der Hilst, R. D.; Huang, Y. C.

    2014-12-01

    Ambient noise tomography has provided essential constraints on crustal and uppermost mantle shear velocity structure in global seismology. Recent studies demonstrate that high frequency (e.g., ~ 1 Hz) surface waves between receivers at short distances can be successfully retrieved from ambient noise cross-correlation and then be used for imaging near surface or shallow crustal shear velocity structures. This approach provides important information for strong ground motion prediction in seismically active area and overburden structure characterization in oil and gas fields. Here we propose a new tomographic method to invert all surface wave dispersion data for 3-D variations of shear wavespeed without the intermediate step of phase or group velocity maps.The method uses frequency-dependent propagation paths and a wavelet-based sparsity-constrained tomographic inversion. A fast marching method is used to compute, at each period, surface wave traveltimes and ray paths between sources and receivers. This avoids the assumption of great-circle propagation that is used in most surface wave tomographic studies, but which is not appropriate in complex media. The wavelet coefficients of the velocity model are estimated with an iteratively reweighted least squares (IRLS) algorithm, and upon iterations the surface wave ray paths and the data sensitivity matrix are updated from the newly obtained velocity model. We apply this new method to determine the 3-D near surface wavespeed variations in the Taipei basin of Taiwan, Hefei urban area and a shale and gas production field in China using the high-frequency interstation Rayleigh wave dispersion data extracted from ambient noisecross-correlation. The results reveal strong effects of off-great-circle propagation of high-frequency surface waves in these regions with above 30% shear wavespeed variations. The proposed approach is more efficient and robust than the traditional two-step surface wave tomography for imaging complex

  8. Analysis of ambient noise in Yalova, Turkey: discrimination between artificial and natural excitations

    Science.gov (United States)

    Yalcinkaya, Esref; Tekebas, Serhat; Pinar, Ali

    2013-07-01

    Ambient noise measurements acquired in Yalova, which was highly damaged during the 1999 Izmit earthquake, are analyzed to explore the site characteristics. The region of Yalova is governed by complex geological and geomorphological structures consisting of river beds extending from the mountains to the sea, ridges between them, plains in front of them with different size, and the sea coast. As a result of these shallow geological features, the H/V curves exhibit complex patterns. Clear peaks in the H/V curves, which can be interpreted as reliable site resonance frequency, are observed only at about half of the measurement sites. At the remaining sites industrial peaks, broad peaks, or flat responses dominate the spectral ratio graphs. We observed that man-made noises generated by marble cutting machines in Hersek delta mask the site resonance frequencies or can be misinterpreted as a resonance frequency. In total, we identified three anthropogenic noise sources at fundamental frequencies of 1.3, 1.5, and 1.7 Hz along with their two- and threefold harmonics. The parts of H/V curves showing unusual low scattering can be a clue to identify anthropogenic effects. In the assessment of H/V curves, the site location and the similarity of the near surface geology were taken into account. The Laledere plain with thick and soft sediment sequence surprisingly displays flat responses due to a possible low impedance contrast. The Ciftlikkoy and Hacimehmet plains exhibit clear resonance peaks at nearly 1 Hz possessing the largest amplitudes. These sites experienced the highest damage in Yalova during the Izmit earthquake. In contrast, the Cinarcik region which was also exposed to high damage, do not show any obvious amplifications on the H/V curves. Generally, the H/V curves for valley and ridge sites in Yalova reveals a resonance peak at approximately 1 Hz and almost flat curves, respectively. However, several sites on the ridges and valleys portray different patterns.

  9. Ambient noise tomography of Ecuador: Fore- and back-arc velocity structure and radial anisotropy

    Science.gov (United States)

    Lynner, C.; Beck, S. L.; Porritt, R.; Meltzer, A.; Alvarado, A. P.; Gabriela, P.; Ruiz, M. C.; Hoskins, M.; Stachnik, J.; Rietbrock, A.; Leon-Rios, S.; Regnier, M. M.; Agurto-Detzel, H.; Font, Y.; Charvis, P.

    2017-12-01

    In northern South America, the oceanic Nazca plate subducts beneath the South American continent, giving rise to the high mountains of the northern Andes. The Ecuador subduction zone has a history of large megathrust earthquakes, most recently the Mw=7.8 April 16, 2016, Pedernales earthquake. The volcanic arc in Ecuador is broad with active volcanoes along both the western and eastern cordilleras. Many of these volcanoes surround the city of Quito putting millions of people at risk. A recent international broadband aftershock deployment was conducted for approximately one year after the Pedernales mainshock and this data combined with a sub-set of data from from the permanent IGEPN national network provide an ideal data set to use for ambient noise tomography (ANT) to constrain absolute Vsh and Vsv across Ecuador. ANT studies use noise-generated surface wave dispersion measurements to invert for 3D shear velocity in the crust. Having a precise understanding of crustal velocity structure is necessary to advance a number of projects, including better earthquake locations of the April 16, 2016 Pedernales-earthquake aftershock sequence and identifying large-scale partial melt zones associated with the active volcanic arc. The majority of ANT studies use only Rayleigh waves to constrain Vsv structure. Initial Rayleigh wave ANT results, using periods between 8 and 40 seconds, show a fast phase velocities for the forearc and much slower phase velocities for the high elevation volcanic arc. Including Love wave dispersion measurements can improve overall crustal velocity models, as well as provide constraints on radial anisotropy. Radial anisotropy can develop in a variety of ways but most typically arises from the deformation-induced alignment of anisotropic minerals. Radial anisotropy, therefore, can inform on patterns of ductile crustal flow. Strong radial anisotropy at mid-crustal depths from ANT has already been observed south of Ecuador, in the Central Andean Plateau

  10. Ambient noise causes independent changes in distinct spectro-temporal features of echolocation calls in horseshoe bats.

    Science.gov (United States)

    Hage, Steffen R; Jiang, Tinglei; Berquist, Sean W; Feng, Jiang; Metzner, Walter

    2014-07-15

    One of the most efficient mechanisms to optimize signal-to-noise ratios is the Lombard effect - an involuntary rise in call amplitude due to ambient noise. It is often accompanied by changes in the spectro-temporal composition of calls. We examined the effects of broadband-filtered noise on the spectro-temporal composition of horseshoe bat echolocation calls, which consist of a constant-frequency component and initial and terminal frequency-modulated components. We found that the frequency-modulated components became larger for almost all noise conditions, whereas the bandwidth of the constant-frequency component increased only when broadband-filtered noise was centered on or above the calls' dominant or fundamental frequency. This indicates that ambient noise independently modifies the associated acoustic parameters of the Lombard effect, such as spectro-temporal features, and could significantly affect the bat's ability to detect and locate targets. Our findings may be of significance in evaluating the impact of environmental noise on echolocation behavior in bats. © 2014. Published by The Company of Biologists Ltd.

  11. Two-receiver measurements of phase velocity: cross-validation of ambient-noise and earthquake-based observations

    NARCIS (Netherlands)

    Kästle, Emanuel D.; Soomro, Riaz; Weemstra, C.; Boschi, Lapo; Meier, Thomas

    2016-01-01

    Phase velocities derived from ambient-noise cross-correlation are compared with phase velocities calculated from cross-correlations of waveform recordings of teleseismic earthquakes whose epicentres are approximately on the station–station great circle. The comparison is conducted both for Rayleigh

  12. Method for measuring self-noise of vector hydrophones

    Science.gov (United States)

    Li, Zhi; Chen, Hongjuan

    2017-09-01

    The Vector Hydrophone (VH) is widely used to remotely detect underwater targets. Accurately measuring the self-noise of the VH provides an important basis for evaluating the performance of the detection system in which it is utilized, since the ability to acquire weak signals is determined by the VH self-noise level. To accurately measure the VH self-noise level in actual working conditions, the Dual-channel Transfer Function Method (DTFM) is proposed to reduce ambient background noise interference. In this paper, the underlying principles of DTFM in reducing ambient background noise is analyzed. The numerical simulations to determine the influence of ambient background noise, and the sensitivity difference of the two VHs on the measurement results are studied. The results of measuring the VH self-noise level in a small laboratory water tank by using DTMF indicate that ambient background noise interference can be reduced effectively by employing DTMF, more accurate self-noise level can be obtained as well. The DTMF provides an effective method for accurately measuring the self-noise level of VHs and also provides technical support for the practical application of the VH in underwater acoustics.

  13. Directionality analysis and Rayleigh wave tomography of ambient seismic noise in southern Norway

    Science.gov (United States)

    Köhler, Andreas; Weidle, Christian; Maupin, Valérie

    2011-01-01

    We process seismic broad-band data from southern Norway by cross correlation of ambient seismic noise in view of getting a better image of the crustal structure in the area. The main data set sterns from the temporary MAGNUS network which operated continuously from 2006 September to 2008 June. Additionally, data from permanent stations of the National Norwegian Seismic Network, the NORSAR array and GSN stations in the region are used. We compute vertical component cross-correlation functions using 41 receivers for 3-month time windows. Evaluation of the azimuthal and temporal variation of signal-to-noise ratios (SNRs) and f-k analysis of data from NORSAR array between 3 and 25 s period shows that the dominant source areas of seismic noise are located to the west and north of the network during most of the measurement time, which corresponds well to the Norwegian coast line. During summer months, the SNRs decrease but the azimuthal distribution becomes more uniform between 7 and 12 s period, suggesting a more diffuse character of the wavefield. Primary ocean microseisms above 12 s show different dominant source azimuths during this time period compared to the winter months. Time-frequency analysis is applied to measure Rayleigh wave group velocity dispersion curves between each station pair for each 3-month correlation stack and the mean and variance of all dispersion curves is computed for each path. After rejection of low-quality data, a careful analysis shows that the group velocities are not biased by noise directionality. We invert the data for group velocity maps at period bands between 3 and 25 s. At short periods, we find an average Rayleigh wave group speed of about 3 km s-1 and velocity anomalies that correlate very well with local surface geology. While higher velocities (+5 per cent) can be associated with the Caledonian nappes in the central part of southern Norway, the Oslo Graben is reflected by negative velocity anomalies (-3 to -5 per cent). At

  14. Maximal Ambient Noise Levels and Type of Voice Material Required for Valid Use of Smartphones in Clinical Voice Research.

    Science.gov (United States)

    Lebacq, Jean; Schoentgen, Jean; Cantarella, Giovanna; Bruss, Franz Thomas; Manfredi, Claudia; DeJonckere, Philippe

    2017-09-01

    Smartphone technology provides new opportunities for recording standardized voice samples of patients and transmitting the audio files to the voice laboratory. This drastically improves the achievement of baseline designs, used in research on efficiency of voice treatments. However, the basic requirement is the suitability of smartphones for recording and digitizing pathologic voices (mainly characterized by period perturbations and noise) without significant distortion. In a previous article, this was tested using realistic synthesized deviant voice samples (/a:/) with three precisely known levels of jitter and of noise in all combinations. High correlations were found between jitter and noise to harmonics ratio measured in (1) recordings via smartphones, (2) direct microphone recordings, and (3) sound files generated by the synthesizer. In the present work, similar experiments were performed (1) in the presence of increasing levels of ambient noise and (2) using synthetic deviant voice samples (/a:/) as well as synthetic voice material simulating a deviant short voiced utterance (/aiuaiuaiu/). Ambient noise levels up to 50 dB A are acceptable. However, signal processing occurs in some smartphones, and this significantly affects estimates of jitter and noise to harmonics ratio when formant changes are introduced in analogy with running speech. The conclusion is that voice material must provisionally be limited to a sustained /a/. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

  15. Crustal thickness across the Trans-European Suture Zone from ambient noise autocorrelations

    Science.gov (United States)

    Becker, G.; Knapmeyer-Endrun, B.

    2018-02-01

    We derive autocorrelations from ambient seismic noise to image the reflectivity of the subsurface and to extract the Moho depth beneath the stations for two different data sets in Central Europe. The autocorrelations are calculated by smoothing the spectrum of the data in order to suppress high amplitude, narrow-band signals of industrial origin, applying a phase autocorrelation algorithm and time-frequency domain phase-weighted stacking. The stacked autocorrelation results are filtered and analysed predominantly in the frequency range of 1-2 Hz. Moho depth is automatically picked inside uncertainty windows obtained from prior information. The processing scheme we developed is applied to data from permanent seismic stations located in different geological provinces across Europe, with varying Moho depths between 25 and 50 km, and to the mainly short period temporary PASSEQ stations along seismic profile POLONAISE P4. The autocorrelation results are spatially and temporarily stable, but show a clear correlation with the existence of cultural noise. On average, a minimum of six months of data is needed to obtain stable results. The obtained Moho depth results are in good agreement with the subsurface model provided by seismic profiling, receiver function estimates and the European Moho depth map. In addition to extracting the Moho depth, it is possible to identify an intracrustal layer along the profile, again closely matching the seismic model. For more than half of the broad-band stations, another change in reflectivity within the mantle is observed and can be correlated with the lithosphere-asthenosphere boundary to the west and a mid-lithospheric discontinuity beneath the East European Craton. With the application of the developed autocorrelation processing scheme to different stations with varying crustal thicknesses, it is shown that Moho depth can be extracted independent of subsurface structure, when station coverage is low, when no strong seismic sources are

  16. A seismic waves velocity model for Gran Canaria Island from ambient noise correlations

    Science.gov (United States)

    García-Jerez, Antonio; Almendros, Javier; Martínez-Arévalo, Carmen; de Lis Mancilla, Flor; Luzón, Francisco; Carmona, Enrique; Martín, Rosa; Sánchez, Nieves

    2014-05-01

    We have analysed continuous ambient seismic noise recorded by a temporary array in Gran Canaria (Canary Islands, Spain) in order to find a velocity model for the top few kilometers. The SISTEVOTENCAN-IGN seismic array consisted of five broadband stations surrounding a sixth central one placed close to Pico de las Nieves, at the center of the island. The array had a radius of 12-14 km, with interstation distances ranging from 10 to 27 km. This network was operative from December 2009 to November 2011. The Green's functions between the 15 pairs of stations have been estimated in the time domain by stacking cross-correlations of 60-s time windows for the whole recording period (~2 years). The effects of several processing adjustments such as 1-bit normalization and spectral whitening are discussed. We observe significant differences (mainly in amplitude) between causal and acausal parts of the estimated Green's functions, which can be associated to an uneven distribution of the seismic noise sources. The application of a phase-matched filter based on an average dispersion curve allowed the effective reduction of some spurious early arrivals and the selection of fundamental-mode Rayleigh wave pulses, making possible an automatic extraction of their group velocities. Then, Rayleigh-wave dispersion curves were retrieved for the set of paths by using frequency-time analysis (FTAN) as well as by following the procedure described by Herrin and Goforth (1977, BSSA) based on the iterative fitting of a phase-matched filter which optimally undisperses the signal. Reliable curves were obtained from 1 s to 6-7 s with group velocities ranging between 1.5 and 2.2 km/s. Some lateral variations in velocity have been detected in spite of the limited spatial coverage and path density, which substantially restricted the resolution. A mean S-wave velocity model has been inverted for this area down to ~3 km.

  17. Monitoring Instrument Performance in Regional Broadband Seismic Network Using Ambient Seismic Noise

    Science.gov (United States)

    Ye, F.; Lyu, S.; Lin, J.

    2017-12-01

    In the past ten years, the number of seismic stations has increased significantly, and regional seismic networks with advanced technology have been gradually developed all over the world. The resulting broadband data help to improve the seismological research. It is important to monitor the performance of broadband instruments in a new network in a long period of time to ensure the accuracy of seismic records. Here, we propose a method that uses ambient noise data in the period range 5-25 s to monitor instrument performance and check data quality in situ. The method is based on an analysis of amplitude and phase index parameters calculated from pairwise cross-correlations of three stations, which provides multiple references for reliable error estimates. Index parameters calculated daily during a two-year observation period are evaluated to identify stations with instrument response errors in near real time. During data processing, initial instrument responses are used in place of available instrument responses to simulate instrument response errors, which are then used to verify our results. We also examine feasibility of the tailing noise using data from stations selected from USArray in different locations and analyze the possible instrumental errors resulting in time-shifts used to verify the method. Additionally, we show an application that effects of instrument response errors that experience pole-zeros variations on monitoring temporal variations in crustal properties appear statistically significant velocity perturbation larger than the standard deviation. The results indicate that monitoring seismic instrument performance helps eliminate data pollution before analysis begins.

  18. Radial anisotropy of Northeast Asia inferred from Bayesian inversions of ambient noise data

    Science.gov (United States)

    Lee, S. J.; Kim, S.; Rhie, J.

    2017-12-01

    The eastern margin of the Eurasia plate exhibits complex tectonic settings due to interactions with the subducting Pacific and Philippine Sea plates and the colliding India plate. Distributed extensional basins and intraplate volcanoes, and their heterogeneous features in the region are not easily explained with a simple mechanism. Observations of radial anisotropy in the entire lithosphere and the part of the asthenosphere provide the most effective evidence for the deformation of the lithosphere and the associated variation of the lithosphere-asthenosphere boundary (LAB). To infer anisotropic structures of crustal and upper-mantle in this region, radial anisotropy is measured using ambient noise data. In a continuation of previous Rayleigh wave tomography study in Northeast Asia, we conduct Love wave tomography to determine radial anisotropy using the Bayesian inversion techniques. Continuous seismic noise recordings of 237 broad-band seismic stations are used and more than 55,000 group and phase velocities of fundamental mode are measured for periods of 5-60 s. Total 8 different types of dispersion maps of Love wave from this study (period 10-60 s), Rayleigh wave from previous tomographic study (Kim et al., 2016; period 8-70 s) and longer period data (period 70-200 s) from a global model (Ekstrom, 2011) are jointly inverted using a hierarchical and transdimensional Bayesian technique. For each grid-node, boundary depths, velocities and anisotropy parameters of layers are sampled simultaneously on the assumption of the layered half-space model. The constructed 3-D radial anisotropy model provides much more details about the crust and upper mantle anisotropic structures, and about the complex undulation of the LAB.

  19. Crust azimuthal anisotropy beneath the eastern Tibetan Plateau revealed by ambient noise tomography

    Science.gov (United States)

    Bao, X.; Song, X.

    2017-12-01

    The continental collision between India and Eurasia in the Cenozoic has resulted in the rise and growth of the vast Tibetan Plateau (TP). Various geodynamic models, such as rigid-block extrusion, continuous deformation, and the mid-lower crustal flow, have been proposed to describe the growth and expansion of eastern Tibet. To better understand the deformation mechanism of the eastern TP, we performed ambient noise tomography using data from permanent and temporary stations and constructed Rayleigh wave azimuthally anisotropic phase-velocity maps at periods from 8 to 30 s, which mainly sample the crustal structure. The dominant direction of fast wave propagation is oriented NW-SE in the northeastern and eastern TP and N-S in the southeastern TP, which is consistent with the trends of main strike-slip faults and the fast polarization directions of SKS waves and suggests vertically coherent deformation. Furthermore, the magnitude of crustal anisotropy is continuous across main strike-slip faults, which contracts with the prediction of rigid-block extrusion model. Taken together, our model supports vertically coherent distributed deformation in the eastern TP.

  20. Upper crustal structure beneath East Java from ambient noise tomography: A preliminary result

    International Nuclear Information System (INIS)

    Martha, Agustya Adi; Widiyantoro, Sri; Cummins, Phil; Saygin, Erdinc; Masturyono

    2015-01-01

    East Java has a fairly complex geological structure. Physiographically East Java can be divided into three zones, i.e. the Southern Mountains zone in the southern part, the Kendeng zone in the middle part, and the Rembang zone in the northern part. Most of the seismic hazards in this region are due to processes in the upper crust. In this study, the Ambient Noise Tomography (ANT) method is used to image the upper crustal structure beneath East Java. We have used seismic waveform data recorded by 8Meteorological, Climatological and Geophysical Agency (BMKG) stationary seismographic stations and 16 portable seismographs installed for 2 to 8 weeks. The data were processed to obtain waveforms fromnoise cross-correlation between pairs of seismographic stations. Our preliminary results indicate that the Kendeng zone, an area of low gravity anomaly, is associated with a low velocity zone. On the other hand, the southern mountain range, which has a high gravity anomaly, is related to a high velocity anomaly as shown by our tomographic images

  1. Environmental seismology: What can we learn on earth surface processes with ambient noise?

    Science.gov (United States)

    Larose, Eric; Carrière, Simon; Voisin, Christophe; Bottelin, Pierre; Baillet, Laurent; Guéguen, Philippe; Walter, Fabian; Jongmans, Denis; Guillier, Bertrand; Garambois, Stéphane; Gimbert, Florent; Massey, Chris

    2015-05-01

    Environmental seismology consists in studying the mechanical vibrations that originate from, or that have been affected by external causes, that is to say causes outside the solid Earth. This includes for instance the coupling between the solid Earth and the cryosphere, or the hydrosphere, the anthroposphere and the specific sources of vibration developing there. Environmental seismology also addresses the modifications of the wave propagation due to environmental forcing such as temperature and hydrology. Recent developments in data processing, together with increasing computational power and sensor concentration have led to original observations that allow for the development of this new field of seismology. In this article, we will particularly review how we can track and interpret tiny changes in the subsurface of the Earth related to external changes from modifications of the seismic wave propagation, with application to geomechanics, hydrology, and natural hazard. We will particularly demonstrate that, using ambient noise, we can track 1) thermal variations in the subsoil, in buildings or in rock columns; 2) the temporal and spatial evolution of a water table; 3) the evolution of the rigidity of the soil constituting a landslide, and especially the drop of rigidity preceding a failure event.

  2. Magmatism on rift flanks: insights from Ambient-Noise Phase-velocity in Afar region

    Science.gov (United States)

    Korostelev, Félicie; Weemstra, Cornelis; Leroy, Sylvie; Boschi, Lapo; Ren, Yong; Ahmed, Abdulhakim; Keir, Derek; Stuart, Graham W.; Rolandone, Frédérique; Khanbari, Khaled; Hammond, James O. S.; Kendall, J. Michael; Doubre, Cécile; Ganad, Ismail Al

    2015-04-01

    During the breakup of continent in the presence of magma, strain is commonly assumed to initially occur by border faulting, and progressively migrate in space and time towards axial magma intrusion. Magmatic processes near the rift flanks are commonly ignored. We present phase-velocity maps of the crust and uppermost mantle of the conjugate margins of the southern Red Sea (Afar and Yemen) using ambient noise tomography to constrain crustal modification during breakup. Our images show that the low seismic velocities characterize not only upper crust beneath the axial volcanic systems, but also both upper and lower crust beneath rift flanks where ongoing volcanism and hydrothermal activity occurs at the surface. The results show that magmatic modification of the crust beneath rift flanks likely occurs for a protracted period of time during the breakup process, and may persist through to early seafloor spreading. Since ongoing flank magmatism during breakup impacts the thermal evolution of the lithosphere, it has implications for the subsidence history of the rift.

  3. High resolution Rayleigh wave group velocity tomography in North-China from ambient seismic noise

    International Nuclear Information System (INIS)

    Fang Lihua; Wu Jianping; Ding Zhifeng; Panza, G.F.

    2009-03-01

    This study presents the results of the Rayleigh wave group velocity tomography in North-China performed using ambient seismic noise observed at 190 broadband and 10 very broadband stations of the North-China Seismic Array. All available vertical component time-series for the 14 months span between January, 2007 and February, 2008 are cross-correlated to obtain empirical Rayleigh wave Green functions that are subsequently processed, with the multiple filter method, to isolate the group velocity dispersion curves of the fundamental mode of Rayleigh wave. Tomographic maps, with a grid spacing of 0.25 deg. x 0.25 deg., are computed at the periods of 4.5s, 12s, 20s, 28s. The maps at short periods reveal an evident lateral heterogeneity in the crust of North-China, quite well in agreement with known geological and tectonic features. The North China Basin is imaged as a broad low velocity area, while the Taihangshan and Yanshan uplifts and Ordos block are imaged as high velocity zones, and the Quaternary intermountain basins show up as small low-velocity anomalies. The group velocity contours at 4.5s, 12s and 20s are consistent with the Bouguer gravity anomalies measured in the area of the Taihangshan fault, that cuts through the lower crust at least. Most of the historical strong earthquakes (M≥6.0) are located where the tomographic maps show zones with moderate velocity gradient. (author)

  4. The crustal structure beneath The Netherlands derived from ambient seismic noise

    Science.gov (United States)

    Yudistira, Tedi; Paulssen, Hanneke; Trampert, Jeannot

    2017-11-01

    This work presents the first comprehensive 3-D model of the crust beneath The Netherlands. To obtain this model, we designed the NARS-Netherlands project, a dense deployment of broadband stations in the area. Rayleigh and Love wave group velocity dispersion was measured from ambient noise cross-correlations. Azimuthally anisotropic group velocity maps were then constructed and the isotropic part was used to determine a shear wave speed model that includes the effects of radial anisotropy. Employing the Neighbourhood Algorithm for the depth inversion, we obtained probabilistic estimates of the radially anisotropic model parameters. We found that the variations in the thickness of the top layer largely match the transition from sediments of Permian age to those of Carboniferous age. Regions of high faulting density such as the West Netherlands Basin and Roer Valley Graben are recognized in our model by their negative radial anisotropy (VSH - VSV Love wave group velocity data at periods of around 20 s show evidence for azimuthal anisotropy with a NW-SE fast direction. This anisotropy is likely related to NW-SE rock fabric in the lower crust thought to originate from the Caledonian deformation.

  5. Intermittent Noise Induces Physiological Stress in a Coastal Marine Fish.

    Directory of Open Access Journals (Sweden)

    Tye A Nichols

    Full Text Available Anthropogenic noise in the ocean has increased substantially in recent decades, and motorized vessels produce what is likely the most common form of underwater noise pollution. Noise has the potential to induce physiological stress in marine fishes, which may have negative ecological consequences. In this study, physiological effects of increased noise (playback of boat noise recorded in the field on a coastal marine fish (the giant kelpfish, Heterostichus rostratus were investigated by measuring the stress responses (cortisol concentration of fish to increased noise of various temporal dynamics and noise levels. Giant kelpfish exhibited acute stress responses when exposed to intermittent noise, but not to continuous noise or control conditions (playback of recorded natural ambient sound. These results suggest that variability in the acoustic environment may be more important than the period of noise exposure for inducing stress in a marine fish, and provide information regarding noise levels at which physiological responses occur.

  6. Intermittent Noise Induces Physiological Stress in a Coastal Marine Fish.

    Science.gov (United States)

    Nichols, Tye A; Anderson, Todd W; Širović, Ana

    2015-01-01

    Anthropogenic noise in the ocean has increased substantially in recent decades, and motorized vessels produce what is likely the most common form of underwater noise pollution. Noise has the potential to induce physiological stress in marine fishes, which may have negative ecological consequences. In this study, physiological effects of increased noise (playback of boat noise recorded in the field) on a coastal marine fish (the giant kelpfish, Heterostichus rostratus) were investigated by measuring the stress responses (cortisol concentration) of fish to increased noise of various temporal dynamics and noise levels. Giant kelpfish exhibited acute stress responses when exposed to intermittent noise, but not to continuous noise or control conditions (playback of recorded natural ambient sound). These results suggest that variability in the acoustic environment may be more important than the period of noise exposure for inducing stress in a marine fish, and provide information regarding noise levels at which physiological responses occur.

  7. Summary report panel 1: the need for protocols and standards in research on underwater noise impacts on marine life

    NARCIS (Netherlands)

    Erbe, C.; Ainslie, M.A.; Jong, C.A.F. de; Racca, R.; Stocker, M.

    2016-01-01

    As concern about anthropogenic noise and its impacts on marine fauna is increasing around the globe, data are being compared across populations, species, noise sources, geographic regions, and time. However, much of the raw and processed data are not comparable due to differences in measurement

  8. Crustal Structure of the Gulf of Aden Continental Margins, from Afar to Oman, by Ambient Noise Seismic Tomography

    Science.gov (United States)

    Korostelev, F.; Weemstra, C.; Boschi, L.; Leroy, S. D.; Ren, Y.; Stuart, G. W.; Keir, D.; Rolandone, F.; Ahmed, A.; Al Ganad, I.; Khanbari, K. M.; Doubre, C.; Hammond, J. O. S.; Kendall, J. M.

    2014-12-01

    Continental rupture processes under mantle plume influence are still poorly known although extensively studied. The Gulf of Aden presents volcanic margins to the west, where they are influenced by the Afar hotspot, and non volcanic margins east of longitude 46° E. We imaged the crustal structure of the Gulf of Aden continental margins from Afar to Oman to evaluate the role of the Afar plume on the evolution of the passive margin and its extent towards the East. We use Ambient Noise Seismic Tomography to better understand the architecture and processes along the Gulf of Aden. This recent method, developed in the last decade, allows us to study the seismic signal propagating between two seismic stations. Ambient Noise Seismic Tomography is thus free from artifacts related to the distribution of earthquakes. We collected continuous records from about 200 permanent or temporary stations since 1999 to compute Rayleigh phase velocity maps over the Gulf of Aden.

  9. Study of site effect using mining induced seismic events and ambient noise from Karviná region

    Czech Academy of Sciences Publication Activity Database

    Kaláb, Zdeněk; Lyubushin, A. A.

    2008-01-01

    Roč. 5, č. 2 (2008), s. 105-113 ISSN 1214-9705. [Polish-Czech-Slovakian Symposium on Mining and Environmental Geophysics/31./. Janov nad Nisou, 24.09.2007-27.09.2007] R&D Projects: GA ČR GA105/07/0878 Institutional research plan: CEZ:AV0Z30860518 Keywords : mining induced seismic event * ambient noise * frequency analysis Subject RIV: DC - Siesmology, Volcanology, Earth Structure http://www.irsm.cas.cz

  10. Seismic site characterization of the Kastelli (Kissamos) Basin in northwest Crete (Greece): Assessments using ambient noise recordings

    OpenAIRE

    Moisidi, M; Vallianatos, F; Kershaw, S; Collins, P

    2015-01-01

    Crete is actively seismic and site response studies are needed for estimating local site conditions subjected to seismic activity. In order to collect basic data, we performed ambient noise recordings to estimate the site response of the surface and near subsurface structure of the small-scale Kastelli Basin in northwest Crete. The spatial horizontal to vertical spectral ratios (HVSR) resonance pattern of the investigated sites in the centre of the Basin consists of either one or two peaks di...

  11. Extraction of Stoneley and acoustic Rayleigh waves from ambient noise on ocean bottom observations

    Science.gov (United States)

    Tonegawa, T.; Fukao, Y.; Takahashi, T.; Obana, K.; Kodaira, S.; Kaneda, Y.

    2013-12-01

    In the interferometry, the wavefield propagating between two positions can be retrieved by correlating ambient noise recorded on the two positions. This approach is useful for applying to various kinds of wavefield, such as ultrasonic, acoustic (ocean acoustic), and also seismology. Off the Kii Peninsula, Japan, more than 150 short-period (4.5 Hz) seismometers, in which hydrophone is also cosited, had been deployed for ~2 months on 2012 by Japan Agency for Marine-Earth Science and Technology (JAMSTEC) as a part of 'Research concerning Interaction Between the Tokai, Tonankai and Nankai Earthquakes' funded by Ministry of Education, Culture, Sports, Science and Technology, Japan. In this study, correlating ambient noise recorded on the sensors and hydrophones, we attempt to investigate characteristics of wavefield relative to the ocean, sediment, and solid-fluid boundary. The observation period is from Sep. 2012 to Dec. 2012. Station spacing is around 5 km. For 5 lines off the Kii Peninsula, the 30-40 seismometers are distributed at each line. Sampling interval is 200 Hz for both seismometer and hydrophone. The vertical component is just used in this study for correlation analysis. The instruments are located at 100-4800 m in water depth. In the processing for the both records, we applied a bandpass filter of 1-3 Hz, replaced the amplitude to zero if it exceeds a value that was set in this study, and took one-bit normalization. We calculated cross-correlation function (CCF) by using continuous records with a time length of 600 s, stacked the CCFs over the whole observation period. As a result of the analysis for hydrophone, a strong peak can be seen in the CCF for pairs of stations where the separation distance is ~5 km. Although the peak emerges in the CCFs for the separation distance up to 10 km, it disappears in the case that two stations are greater than 15 km separated. As a next approach, along a line off the Kii Peninsula, we aligned CCFs for two stations with

  12. The Plumbing System Feeding the Lusi Eruption Revealed by Ambient Noise Tomography

    Science.gov (United States)

    Fallahi, Mohammad Javad; Obermann, Anne; Lupi, Matteo; Karyono, Karyono; Mazzini, Adriano

    2017-10-01

    Lusi is a sediment-hosted hydrothermal system featuring clastic-dominated geyser-like eruption behavior in East Java, Indonesia. We use 10 months of ambient seismic noise cross correlations from 30 temporary seismic stations to obtain a 3-D model of shear wave velocity anomalies beneath Lusi, the neighboring Arjuno-Welirang volcanic complex, and the Watukosek fault system connecting the two. Our work reveals a hydrothermal plume, rooted at a minimum 6 km depth that reaches the surface at the Lusi site. Furthermore, the inversion shows that this vertical anomaly is connected to the adjacent volcanic complex through a narrow ( 3 km wide) low velocity corridor slicing the survey area at a depth of 4-6 km. The NE-SW direction of this elongated zone matches the strike of the Watukosek fault system. Distinct magmatic chambers are also inferred below the active volcanoes. The large-scale tomography features an exceptional example of a subsurface connection between a volcanic complex and a solitary erupting hydrothermal system hosted in a hydrocarbon-rich back-arc sedimentary basin. These results are consistent with a scenario where deep-seated fluids (e.g., magmas and released hydrothermal fluids) flow along a region of enhanced transmissivity (i.e., the Watukosek fault system damage zone) from the volcanic arc toward the back arc basin where Lusi resides. The triggered metamorphic reactions occurring at depth in the organic-rich sediments generated significant overpressure and fluid upwelling that is today released at the spectacular Lusi eruption site.

  13. Crustal Seismic Vs and Vs anisotropy of Northeast Japan Revealed by Ambient Noise Tomography

    Science.gov (United States)

    Chen, K. X.; Gung, Y.; Kuo, B. Y.; Huang, T. Y.

    2017-12-01

    We present 3D crustal models of Vs and Vs azimuthal anisotropy of the Tohoku region, Japan. We employ the Welch's method to derive the empirical Green's functions (EGF) of Rayleigh waves from one year of continuous records of 123 short-period stations of the dense high-sensitivity seismograph network (Hi-net). We compute EGFs for about 4000 station pairs with interstation distance less than 300 km. For each qualified EGF, we measure the dispersion in the period range from 3 to 16 seconds. We then construct the models by using a wavelet-based multi-scale inversion technique. In the resulting models, characteristics of Vs variations and Vs azimuthal anisotropy are closely related to surface geology, Quaternary volcano activities, and plate motions. For the Vs variations in the shallow crust (well correlated to the volcano belt. For the Vs anisotropy, the strength and the patterns of fast polarization directions (FPD) are depth-dependent. In the shallow crust, the anisotropy is strong, and are dominated by the typical orogeny parallel anisotropy, with FPDs parallel to the main strikes of the mountain range. While in the lower crust, the FPDs are generally parallel to the absolute plate motion. Interestingly, the distribution of PFDs is rather chaotic and strength of anisotropy is weak in the middle crust ( 8 - 20 km). We propose that the weak and random anisotropy in this layer is likely related to the presence of magma reservoirs beneath the volcano belt, as the associated active volcanism may cause the destruction of the alignment of crustal fabrics Key words: Tohoku, ambient noise, seismic anisotropy, surface wave tomography, volcano activities

  14. Ambient seismic noise levels: A survey of the permanent and temporary seismographic networks in Morocco, North Africa

    Science.gov (United States)

    El Fellah, Y.; Khairy Abd Ed-Aal, A.; El Moudnib, L.; Mimoun, H.; Villasenor, A.; Gallart, J.; Thomas, C.; Elouai, D.; Mimoun, C.; Himmi, M.

    2013-12-01

    Abstract The results, of a conducted study carried out to analyze variations in ambient seismic noise levels at sites of the installed broadband stations in Morocco, North Africa, are obtained. The permanent and the temporary seismic stations installed in Morocco of the Scientific Institute ( IS, Rabat, Morocco), institute de Ciencias de la Tierra Jaume almera (ICTJA, Barcelona, Spain) and Institut für Geophysik (Munster, Germany) were used in this study. In this work, we used 23 broadband seismic stations installed in different structural domains covering all Morocco from south to north. The main purposes of the current study are: 1) to present a catalog of seismic background noise spectra for Morocco obtained from recently installed broadband stations, 2) to assess the effects of experimental temporary seismic vault construction, 3) to determine the time needed for noise at sites to stabilize, 4) to establish characteristics and origin of seismic noise at those sites. We calculated power spectral densities of background noise for each component of each broadband seismometer deployed in the different investigated sites and then compared them with the high-noise model and low-noise Model of Peterson (1993). All segments from day and night local time windows were included in the calculation without parsing out earthquakes. The obtained results of the current study could be used forthcoming to evaluate permanent station quality. Moreover, this study could be considered as a first step to develop new seismic noise models in North Africa not included in Peterson (1993). Keywords Background noise; Power spectral density; Model of Peterson; Scientific Institute; Institute de Ciencias de la Tierra Jaume almera; Institut für Geophysik

  15. Variability in ambient noise levels and call parameters of North Atlantic right whales in three habitat areas.

    Science.gov (United States)

    Parks, Susan E; Urazghildiiev, Ildar; Clark, Christopher W

    2009-02-01

    The North Atlantic right whale inhabits the coastal waters off the east coasts of the United States and Canada, areas characterized by high levels of shipping and fishing activities. Acoustic communication plays an important role in the social behavior of these whales and increases in low-frequency noise may be leading to changes in their calling behavior. This study characterizes the ambient noise levels, including both natural and anthropogenic sources, and right whale upcall parameters in three right whale habitat areas. Continuous recordings were made seasonally using autonomous bottom-mounted recorders in the Bay of Fundy, Canada (2004, 2005), Cape Cod Bay, (2005, 2006), and off the coast of Georgia (2004-2005, 2006-2007). Consistent interannual trends in noise parameters were found for each habitat area, with both the band level and spectrum level measurements higher in the Bay of Fundy than in the other areas. Measured call parameters varied between habitats and between years within the same habitat area, indicating that habitat area and noise levels alone are not sufficient to predict variability in call parameters. These results suggest that right whales may be responding to the peak frequency of noise, rather than the absolute noise level in their environment.

  16. Assessment of ambient noise levels in the intensive care unit of a university hospital

    Directory of Open Access Journals (Sweden)

    Hatem O Qutub

    2009-01-01

    Conclusion : Some sources of environmental noise, such as the use of oxygen, suction equipment or respirators are unavoidable. Nevertheless, hospital ICUs should have measures to minimize the level of exposure to noise in the ICU. Further research in this area might focus on the noise level and other modifiable environmental stress factors in the ICU that affect patients as well as the staff.

  17. Combined effects of road traffic noise and ambient air pollution in relation to risk for stroke?

    DEFF Research Database (Denmark)

    Sørensen, Mette; Lühdorf, Pernille; Ketzel, Matthias

    2014-01-01

    Exposure to road traffic noise and air pollution have both been associated with risk for stroke. The few studies including both exposures show inconsistent results. We aimed to investigate potential mutual confounding and combined effects between road traffic noise and air pollution in association...... to 2009 were identified in national registers and road traffic noise and air pollution were modeled for all addresses. Analyses were done using Cox regression. A higher mean annual exposure at time of diagnosis of 10µg/m(3) nitrogen dioxide (NO2) and 10dB road traffic noise at the residential address...... was found for combination of high noise and high NO2 (IRR=1.28; 95% CI=1.09-1.52). Fatal stroke was positively associated with air pollution and not with traffic noise. In conclusion, in mutually adjusted models road traffic noise and not air pollution was associated ischemic stroke, while only air...

  18. Summary Report Panel 1: The Need for Protocols and Standards in Research on Underwater Noise Impacts on Marine Life.

    Science.gov (United States)

    Erbe, Christine; Ainslie, Michael A; de Jong, Christ A F; Racca, Roberto; Stocker, Michael

    2016-01-01

    As concern about anthropogenic noise and its impacts on marine fauna is increasing around the globe, data are being compared across populations, species, noise sources, geographic regions, and time. However, much of the raw and processed data are not comparable due to differences in measurement methodology, analysis and reporting, and a lack of metadata. Common protocols and more formal, international standards are needed to ensure the effectiveness of research, conservation, regulation and practice, and unambiguous communication of information and ideas. Developing standards takes time and effort, is largely driven by a few expert volunteers, and would benefit from stakeholders' contribution and support.

  19. The underwater acoustic environment at SGaan Kinghlas-Bowie Seamount Marine Protected Area: Characterizing vessel traffic and associated noise using satellite AIS and acoustic datasets.

    Science.gov (United States)

    Allen, Ainsley S; Yurk, Harald; Vagle, Svein; Pilkington, James; Canessa, Rosaline

    2018-03-01

    Vessel traffic is one of the most wide-spread anthropogenic contributors to ocean noise worldwide and has the potential to alter ecosystems upon which cetaceans and other acoustically sensitive marine organisms rely. Canada's SGaan Kinghlas-Bowie Seamount Marine Protected Area (SK-B MPA) is one such area whose productive ecosystem could benefit from greater monitoring of human induced threats in order to inform management. Despite earning official designation as a Marine Protected Area under the Oceans Act in 2008, little remains known about vessel traffic in the region and the associated potential impacts on vulnerable marine species. Therefore, to increase our understanding of vessel traffic and accompanying noise at SK-B MPA, satellite AIS and acoustic data were investigated. The results of this study suggest that variations in ambient sound levels in the region are driven by near and distant shipping events, thus having implications for future management of the MPA. Copyright © 2018 Elsevier Ltd. All rights reserved.

  20. Underwater robots

    CERN Document Server

    Antonelli, Gianluca

    2014-01-01

    This book, now at the third edition, addresses the main control aspects in underwater manipulation tasks. The mathematical model with significant impact on the control strategy is discussed. The problem of controlling a 6-degrees-of-freedoms autonomous underwater vehicle is deeply investigated and a survey of fault detection/tolerant strategies for unmanned underwater vehicles is provided. Inverse kinematics, dynamic and interaction control for underwater vehicle-manipulator systems are then discussed. The code used to generate most of the numerical simulations is made available and briefly discussed.       

  1. Auditory map reorganization and pitch discrimination in adult rats chronically exposed to low-level ambient noise

    Science.gov (United States)

    Zheng, Weimin

    2012-01-01

    Behavioral adaption to a changing environment is critical for an animal's survival. How well the brain can modify its functional properties based on experience essentially defines the limits of behavioral adaptation. In adult animals the extent to which experience shapes brain function has not been fully explored. Moreover, the perceptual consequences of experience-induced changes in the brains of adults remain unknown. Here we show that the tonotopic map in the primary auditory cortex of adult rats living with low-level ambient noise underwent a dramatic reorganization. Behaviorally, chronic noise-exposure impaired fine, but not coarse pitch discrimination. When tested in a noisy environment, the noise-exposed rats performed as well as in a quiet environment whereas the control rats performed poorly. This suggests that noise-exposed animals had adapted to living in a noisy environment. Behavioral pattern analyses revealed that stress or distraction engendered by the noisy background could not account for the poor performance of the control rats in a noisy environment. A reorganized auditory map may therefore have served as the neural substrate for the consistent performance of the noise-exposed rats in a noisy environment. PMID:22973201

  2. Impact of wind on ambient noise recorded by the "13 BB star" seismic array in northern Poland

    Science.gov (United States)

    Lepore, Simone; Markowicz, Krzysztof; Grad, Marek

    2016-04-01

    Seismic interferometry and beam forming techniques were applied to ambient noise recorded during January 2014 at the "13 BB star" array, composed of thirteen seismic stations located in northern Poland, with the aim of evaluating the azimuth of noise sources and the velocities of surface waves. After normalizing the raw recordings in time and frequency domain, the spectral characteristics of the ambient noise were studied to choose a frequency band suitable for the waves' retrieval. To get the velocity of surface waves by seismic interferometry, the crosscorrelation between all station pairs was analysed for the vertical and horizontal components in the 0.05-0.1 Hz, 0.1-1 Hz and 1 10 Hz frequency bands. For each pair, the crosscorrelation was applied to one hour recordings extracted from the ambient noise. The obtained traces were calculated for a complete day, and then summed together: the daily results were stacked for the whole January 2014. In the lowest frequency range, most of the energy is located around the 3.0 km/s line, meaning that the surface waves coming from the uppermost mantle will be retrieved. The intermediate frequency range shows most of the energy between the 2.0 km/s and 1.5 km/s lines: consequently, surface waves originating from the crust will be retrieved. In the highest frequency range, the surface waves are barely visible on the crosscorrelation traces, implying that the associated energy is strongly attenuated. The azimuth variation associated to the noise field was evaluated by means of the beam forming method, using the data from the whole array for all the three components. To that, the beam power was estimated in a small range of frequencies every day for the whole month. For each day, one hour long results of beam forming applications were stacked together. To avoid aliasing and near field effects, the minimum frequency was set at 0.05 Hz and the maximum to 0.1 Hz. In this frequency band, the amplitude maximum was sought

  3. Google™ underwater

    Science.gov (United States)

    Showstack, Randy

    2012-10-01

    The first underwater panoramic images were added to Google Maps™, the company announced on 25 September. This first “underwater Street View collection,” launched in partnership with the Caitlin Seaview Survey, provides people with the opportunity to “become the next virtual Jacques Cousteau.” For more information, see: maps.google.com/ocean.

  4. Does ambient noise or hypobaric atmosphere influence olfactory and gustatory function?

    Science.gov (United States)

    Rahne, Torsten; Köppke, Robert; Nehring, Michael; Plontke, Stefan K; Fischer, Hans-Georg

    2018-01-01

    Multidimensional food perception is based mainly on gustatory and olfactory function. Recent research has demonstrated that hypobaric pressure impairs gustatory function and that background noise or distracting auditory stimulation impairs olfactory function. Using a hypobaric chamber, the odor identification, discrimination, and thresholds as well as taste identification and threshold scores were measured in 16 healthy male volunteers under normal and hypobaric (6380 ft) conditions using clinically validated tests. In both conditions, background noise was either canceled out or replaced by white noise presentation (70 dB sound pressure level). Olfactory sensitivity for n-butanol and gustatory sensitivity were impaired in a hypobaric atmosphere. White noise did not influence the odor test results. White noise stimulation impaired sensitivity for sour and sweet but not for bitter or salty tastants. We conclude that hypobaric or noisy environments could impair gustatory and olfactory sensitivity selectively for particular tastants and odorants.

  5. Combined effects of road traffic noise and ambient air pollution in relation to risk for stroke?

    Science.gov (United States)

    Sørensen, Mette; Lühdorf, Pernille; Ketzel, Matthias; Andersen, Zorana J; Tjønneland, Anne; Overvad, Kim; Raaschou-Nielsen, Ole

    2014-08-01

    Exposure to road traffic noise and air pollution have both been associated with risk for stroke. The few studies including both exposures show inconsistent results. We aimed to investigate potential mutual confounding and combined effects between road traffic noise and air pollution in association with risk for stroke. In a population-based cohort of 57,053 people aged 50-64 years at enrollment, we identified 1999 incident stroke cases in national registries, followed by validation through medical records. Mean follow-up time was 11.2 years. Present and historical residential addresses from 1987 to 2009 were identified in national registers and road traffic noise and air pollution were modeled for all addresses. Analyses were done using Cox regression. A higher mean annual exposure at time of diagnosis of 10 µg/m(3) nitrogen dioxide (NO2) and 10 dB road traffic noise at the residential address was associated with ischemic stroke with incidence rate ratios (IRR) of 1.11 (95% CI: 1.03, 1.20) and 1.16 (95% CI: 1.07, 1.24), respectively, in single exposure models. In two-exposure models road traffic noise (IRR: 1.15) and not NO2 (IRR: 1.02) was associated with ischemic stroke. The strongest association was found for combination of high noise and high NO2 (IRR=1.28; 95% CI=1.09-1.52). Fatal stroke was positively associated with air pollution and not with traffic noise. In conclusion, in mutually adjusted models road traffic noise and not air pollution was associated ischemic stroke, while only air pollution affected risk for fatal strokes. There were indications of combined effects. Copyright © 2014 Elsevier Inc. All rights reserved.

  6. Seismic constraints on magma evolution beneath Mount Baekdu (Changbai) volcano from transdimensional Bayesian inversion of ambient noise data

    Science.gov (United States)

    Kim, Seongryong; Tkalčić, Hrvoje; Rhie, Junkee

    2017-07-01

    The magmatic process of continental intraplate volcanism (CIV) is difficult to understand due to heterogeneous interactions with the crust and the lithospheric upper mantle. Mount Baekdu (Changbai) volcano (MBV) is one of the prominent CIVs in northeast Asia that has shown a complex history of eruptions and associated magmatic structures. In addition, the relationship between the crustal magmatic structures and upper mantle phenomena are enigmatic due to the lack of consistent seismic constraints for the lithospheric structure. To enhance comprehensive understanding of the MBV magma evolution, we image the lithospheric structure beneath the MBV and surrounding regions using ambient noise data and the following two approaches: (1) multiple measures of ambient noise dispersion are acquired through different methods and (2) a transdimensional Bayesian inversion method is utilized to obtain unbiased results in joint analysis of the multiple data sets. The estimated Earth structure shows a thick crust ( 40 km) and a crustal anomaly with relatively high S wave velocity in the depth range 20-40 km. This type of structure extends to 100 km north from the MBV and is accompanied by the shallow and rapid S wave velocity decrease beneath the mantle lid ( 80 km). Through a comparison with previous P wave models, we interpret this structure as a consequence of compositional partitioning by mafic underplating and overlying cooled felsic layers as a result of fractional crystalization.

  7. Refinements to the method of epicentral location based on surface waves from ambient seismic noise: introducing Love waves

    Science.gov (United States)

    Levshin, Anatoli L.; Barmin, Mikhail P.; Moschetti, Morgan P.; Mendoza, Carlos; Ritzwoller, Michael H.

    2012-01-01

    The purpose of this study is to develop and test a modification to a previous method of regional seismic event location based on Empirical Green’s Functions (EGFs) produced from ambient seismic noise. Elastic EGFs between pairs of seismic stations are determined by cross-correlating long ambient noise time-series recorded at the two stations. The EGFs principally contain Rayleigh- and Love-wave energy on the vertical and transverse components, respectively, and we utilize these signals between about 5 and 12 s period. The previous method, based exclusively on Rayleigh waves, may yield biased epicentral locations for certain event types with hypocentral depths between 2 and 5 km. Here we present theoretical arguments that show how Love waves can be introduced to reduce or potentially eliminate the bias. We also present applications of Rayleigh- and Love-wave EGFs to locate 10 reference events in the western United States. The separate Rayleigh and Love epicentral locations and the joint locations using a combination of the two waves agree to within 1 km distance, on average, but confidence ellipses are smallest when both types of waves are used.

  8. The Influence of Changing Sea Conditions on Shipping Noise, Including Effects of Wind, Fish and Climate Change

    NARCIS (Netherlands)

    Ainslie, M.A.; Jong, C.A.F. de

    2011-01-01

    Early human interest in ambient noise in the sea, especially during and after the Second World War, resulted from its effect on limiting the performance of military search sonar [Urick 1983]. While that interest continues, it is now accompanied by non-military uses of underwater sound, such as

  9. Underwater Vehicle

    National Research Council Canada - National Science Library

    Dick, James L

    2007-01-01

    There is thus provided an underwater vehicle having facility for maneuvering alongside a retrieving vehicle, as by manipulation of bow and stern planes, for engaging a hull surface of the retrieving...

  10. Analysis of the levels of ambient noise present in the Colonia Auditorium (October 2001)

    Science.gov (United States)

    Jalisco, Zapopan; Palafox, Lourdes; Orozco, Martha; Rodriguez, Erika

    2002-11-01

    The study area is located in the city of Guadalajara, defined by: delimited in the north by the Gonzlez Gallo street; in the south by the Anillo Perifrico street; in the east by Avenida Mezquitan; and in the west by Avenida Alcalde. There were 38 measurement points outside the auditorium and 25 inside. A poll was conducted among the neighbors and visitors in both areas, getting 70 replies. Noise levels were between 41-101 dB(A) on the outside, average Leq on the outside was 64.5 dB(A), and inside was 80.15 dB(A). The conclusion is that the whole area is affected by traffic noise, as well by the huge number of visitors, the electric games, and the electric generators that supply energy to them. On the outside 21 points were above 65 dB(A), which means that 55% were above the average; on the inside, 100% were above 65 dB(A). Thus the neighbors are exposed to high noise levels due to the festivities during October. The biggest problem, however, is the noise exposure of the workers inside the auditorium, due to music, games, people, and electric generators.

  11. Gestational diabetes mellitus and exposure to ambient air pollution and road traffic noise

    DEFF Research Database (Denmark)

    Pedersen, Marie; Olsen, Sjurdur F; Halldorsson, Thorhallur I

    2017-01-01

    Background: Road traffic is a main source of air pollution and noise. Both exposures have been associated with type 2 diabetes, but associations with gestational diabetes mellitus (GDM) have been studied less. Objectives: We aimed to examine single and joint associations of exposure to air pollut...

  12. Gestational diabetes mellitus and exposure to ambient air pollution and road traffic noise: A cohort study.

    Science.gov (United States)

    Pedersen, Marie; Olsen, Sjurdur F; Halldorsson, Thorhallur I; Zhang, Cuilin; Hjortebjerg, Dorrit; Ketzel, Matthias; Grandström, Charlotta; Sørensen, Mette; Damm, Peter; Langhoff-Roos, Jens; Raaschou-Nielsen, Ole

    2017-11-01

    Road traffic is a main source of air pollution and noise. Both exposures have been associated with type 2 diabetes, but associations with gestational diabetes mellitus (GDM) have been studied less. We aimed to examine single and joint associations of exposure to air pollution and road traffic noise on GDM in a prospective cohort. We identified GDM cases from self-reports and hospital records, using two different criteria, among 72,745 singleton pregnancies (1997-2002) from the Danish National Birth Cohort. We modeled nitrogen dioxide (NO 2 ) and noise from road traffic (L den ) exposure at all pregnancy addresses. According to the two diagnostic criteria: the Danish clinical guidelines, which was our main outcome, and the WHO standard during recruitment period, a total of 565 and 210 women, respectively, had GDM. For both exposures no risk was evident for the common Danish criterion of GDM. A 10-μg/m 3 increase in NO 2 exposure during first trimester was, however, associated with an increased risk of WHO-GDM (adjusted odds ratio (OR)=1.24; 95% confidence interval (CI): 1.03, 1.49). The corresponding OR associated with a 10-dB higher road traffic noise level was 1.15 (0.94 to 1.18). In mutually adjusted models the OR for NO 2 remained similar 1.22 (0.98, 1.53) whereas that for road traffic noise decreased to 1.03 (0.80, 1.32). Significant associations were also observed for exposure averaged over the 2nd and 3rd trimesters and the full pregnancy. No risk was evident for the common Danish criterion of GDM. NO 2 was associated with higher risk for GDM according to the WHO criterion, which might be due to selection bias. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Underwater laser detection system

    Science.gov (United States)

    Gomaa, Walid; El-Sherif, Ashraf F.; El-Sharkawy, Yasser H.

    2015-02-01

    The conventional method used to detect an underwater target is by sending and receiving some form of acoustic energy. But the acoustic systems have limitations in the range resolution and accuracy; while, the potential benefits of a laserbased underwater target detection include high directionality, high response, and high range accuracy. Lasers operating in the blue-green region of the light spectrum(420 : 570nm)have a several applications in the area of detection and ranging of submersible targets due to minimum attenuation through water ( less than 0.1 m-1) and maximum laser reflection from estimated target (like mines or submarines) to provide a long range of detection. In this paper laser attenuation in water was measured experimentally by new simple method by using high resolution spectrometer. The laser echoes from different targets (metal, plastic, wood, and rubber) were detected using high resolution CCD camera; the position of detection camera was optimized to provide a high reflection laser from target and low backscattering noise from the water medium, digital image processing techniques were applied to detect and discriminate the echoes from the metal target and subtract the echoes from other objects. Extraction the image of target from the scattering noise is done by background subtraction and edge detection techniques. As a conclusion, we present a high response laser imaging system to detect and discriminate small size, like-mine underwater targets.

  14. Understanding the formation of the Ontong Java Plateau through joint ambient noise earthquake tomography and laboratory modeling

    Science.gov (United States)

    Covellone, B. M.; Szwaja, S.; Savage, B. K.; Shen, Y.; Kincaid, C. R.

    2013-12-01

    Current knowledge of the Ontong Java Plateau (OJP) comes from a broad range of research disciplines. Despite decades of work, numerous hypotheses on the origin of the OJP do not fully address all of the geophysical and geochemical observations. A more complete image of the current lower crust and upper mantle seismic structure beneath the plateau will provide a link between the plateau's 120 Ma complex history and it's formation. We investigate the anomalous wave speed structure underlying the OJP using an iterative, full-waveform, joint ambient noise and earthquake tomography approach. A 3-dimensional wave speed model is determined from ambient noise data at periods between 25 and 200 seconds. Data from over 100 earthquakes, recorded between 1990 and 2012, are then added to the inversion to improve data coverage and model resolution. The combination of datasets allows us to best exploit the limited station distribution in the Pacific, resulting in resolution better than 5-degrees beneath the plateau and extending to depths greater than 350 km. To improve our sense of expected deformation patterns for sub-plateau mantle through geologic time, a set of laboratory models were run where OJP residuum viscosity is changed relative to the ambient fluid. Models focus on the interaction between OJP residuum and the rollback-driven flow associated with passage of the Tonga subduction system to the south. Model results show dramatic thinning and extraction of the southern portion of sub-OJP fluid due to subduction induced torroidal flows. Significant distortion of the sub-OJP material over roughly the last 40 Ma is predicted in cases where residuum is either stronger or weaker than ambient fluid. The results of this work confirm an anomalously slow mantle beneath the OJP extending to depths greater than 300 km and provide high-resolution images constraining the magnitude and dimensions of wave speed anomalies that can be used to determine thermal and compositional variations

  15. SIMULATION AND ANALYSIS OF GREEDY ROUTING PROTOCOL IN VIEW OF ENERGY CONSUMPTION AND NETWORK LIFETIME IN THREE DIMENSIONAL UNDERWATER WIRELESS SENSOR NETWORK

    Directory of Open Access Journals (Sweden)

    SHEENA KOHLI

    2017-11-01

    Full Text Available Underwater Wireless Sensor Network (UWSN comprises of a number of miniature sized sensing devices deployed in the sea or ocean, connected by dint of acoustic links to each other. The sensors trap the ambient conditions and transmit the data from one end to another. For transmission of data in any medium, routing protocols play a crucial role. Moreover, being battery limited, an unavoidable parameter to be considered in operation and analysis of protocols is the network energy and the network lifetime. The paper discusses the greedy routing protocol for underwater wireless sensor networks. The simulation of this routing protocol also takes into consideration the characteristics of acoustic communication like attenuation, transmission loss, signal to noise ratio, noise, propagation delay. The results from these observations may be used to construct an accurate underwater communication model.

  16. Noise

    Science.gov (United States)

    Noise is all around you, from televisions and radios to lawn mowers and washing machines. Normally, you ... sensitive structures of the inner ear and cause noise-induced hearing loss. More than 30 million Americans ...

  17. Crustal structure determined from ambient noise tomography near the magmatic centers of the Coso region, southeastern California

    Science.gov (United States)

    Yang, Yingjie; Ritzwoller, Michael H.; Jones, Craig H.

    2011-02-01

    We apply seismic ambient noise tomography to image and investigate the shallow shear velocity structure beneath the Coso geothermal field and surrounding areas. Data from a PASSCAL experiment operated within the Coso geothermal field between 1998 and 2000 and surrounding broadband stations from the Southern California Seismic Network are acquired and processed. Daily cross correlations of ambient noise between all pairs of stations that overlapped in time of deployment were calculated and then stacked over the duration of deployment. Phase velocities of Rayleigh waves between 3 and 10 s periods are measured from the resulting cross correlations. Depending on the period, between about 300 and 600 reliable phase velocity measurements are inverted for phase velocity maps from 3 to 10 s periods, which in turn are inverted for a 3-D shear velocity model beneath the region. The resulting 3-D model reveals features throughout the region that correlate with surface geology. Beneath the Coso geothermal area shear velocities are generally depressed, a prominent low-velocity anomaly is resolved clearly within the top 2 km, no significant anomaly is seen below about 14 km depth, and a weakly resolved anomaly is observed between 6 and 12 km depth. The anomaly in the top 2 km probably results from geothermal alteration in the shallow subsurface, no magmatic body is imaged beneath 14 km depth, but the shear velocity anomaly between 6 and 12 km may be attributable to partial melt. The thickness and amplitude of the magma body trade off in the inversion and are ill determined. Low velocities in the regions surrounding Coso at depths near 7 km underlie areas with Miocene to recent volcanism, suggesting that some magmatic processing of the crust could be focused near this depth.

  18. 4-D permafrost thaw observations from ambient road traffic noise and a very dense distributed fiber optic sensing array

    Science.gov (United States)

    Lindsey, N.; Dou, S.; Martin, E. R.; Wagner, A. M.; Ajo Franklin, J. B.

    2017-12-01

    How does frozen soil thaw? The answer to this question affects hydrology, ecology, climate, and human infrastructure. We are using the local ambient noise field from a road recorded on a distributed fiber optic acoustic sensing (DAS) array to monitor the evolution in seismic parameters related to the top-down permafrost thaw process in the upper 10 m. Our field experiment demonstrates the advantages of "Large N" ambient noise studies using DAS, particularly to probe near surface critical zone dynamics. Over 60 days beginning in August 2016, we made continuous seismic recordings with a >4000 channel trenched fiber optic DAS dataset above a controlled permafrost warming demonstration experiment in Fairbanks, AK. The warming experiment accelerated the state of permafrost degradation by approximately two decades in a small 15 m x 20 m area, deepening the permafrost table from 4 m to 5.5 m. Continuous seismic DAS recording of high frequency surface waves (5-30 Hz) generated by vehicles traveling along a nearby road enables our investigation of hypothesized shear wave speed and attenuation changes, which lab measurements suggest may result from decreasing shear modulus and increasing saturation. We develop daily auto- and crosscorrelation function estimates using combinations of horizontal inline, collinear, and crossline DAS sensor orientations and vertical component geophone data, and then invert for maps of Love and Rayleigh wave speed that are sensitive to the upper 30 m. Many issues related to the accuracy, stability, and repeatability of the recovered empirical Green's tensor, as well as the sensitivity of the DAS sensor network will be considered.

  19. Crustal and uppermantle velocity structure of the northern Korean Peninsula constrained by ambient noise cross-correlations

    Science.gov (United States)

    Lee, S. J.; Rhie, J.; Kim, S.

    2014-12-01

    The seismic velocity structure of the northern Korean Peninsula has not been well known because available seismic data observed inside the region is very rare. Therefore, constructing a one-dimensional (1-D) reference velocity model will be a meaningful first step to understand the detailed velocity structure and also the tectonic evolution of the region. In this study, we use two-year long (2010-2011) ambient noise data recorded by three component broadband seismometers of KIGAM, KMA, F-net, and IRIS networks surrounding the study area. Ambient noise cross-correlations are calculated for station pairs sampling the study area. Multiple filter technique is applied to measure group and phase velocity dispersions of the fundamental mode Rayleigh and Love waves for period ranges between 5 and 70 s, which are sensitive to shear wave velocities in the crust and uppermost mantle. Recently developed inversion method using the Bayesian technique is applied to estimate 1-D models of shear wave velocities and corresponding uncertainties. Combined with the Markov chain Monte Carlo (MCMC) technique, the posterior probability density is evaluated for given data and the prior. Boundaries, velocities, and anisotropy parameters of layers are searched together on the assumption of the layered half-space model. The used method automatically adjusts the number of layers and degree of data fitting by the Bayesian Information Criterion (BIC) estimation and scaling of the data-covariance matrix, respectively. The estimated anisotropic S-wave velocity model in the crust and upper-mantle can help to investigate tectonic processes of the region. For practical use, our velocity model for the Northern Korean Peninsula can be useful to enhance monitoring power of the underground nuclear tests in given area.

  20. Ambient seismic noise as an interesting indirect cue for the Cerithidea decollata migrations

    Science.gov (United States)

    Pazzi, Veronica; Lotti, Alessia

    2017-04-01

    Presence or absence of water, food availability, capability of avoiding predation, and body temperature are constantly changing according to the tidal excursion. In fact, more than the diurnal light-dark variation, tide is shaping the whole intertidal animal life. Therefore, physiological and behavioural systems exist to reduce the stress that the intertidal fauna may face during the unsuitable tidal phase. Cerithidea decollata is a common western Indian Ocean mangrove gastropod. It feeds on the ground at low tide, and climbs the trees two/three hours before the water arrival to avoid submersion. In spite of the irregular East African tidal pattern, it also regularly settles on trunks roughly 40 cm above the maximum level of the incoming tide. Migrations usually take place about twice a day unless at Neap Tide, when snails may remain on the dry ground. Past experiments showed that a biological clock cannot account for water level foreseeing, nor direct visual cues or chemical information from the water itself or from previous migrations have been detected. On the other hand, tidal gravity variations can be felt by the snails. Moreover, other indirect cues could be hypothesize related to a) the oceanic waves reaching the coast and the barrier reef (seismic noise), or b) the changes in ground resistivity (self potential) caused by the sea water moving close. To verify these hypotheses, an integrated geophysical survey (single-station seismic noise and self potential survey) was carried out at Mida Creek (Kenya) to characterize the local seismic wavefield in terms of its amplitude and to measure the temporal variations of the electric potential field. Final goal was to verify whether a correlation exists between the time evolution of these phenomena and the snail movements. Here we present the first results of the seismic noise measurements. Data were acquired by means of a single station all-in-one 3-directional 24-bit digital tromometer equipped with 4.5 Hz

  1. Variations of local seismic response in Benevento (Southern Italy) using earthquakes and ambient noise recordings

    Science.gov (United States)

    Improta, Luigi; di Giulio, Giuseppe; Rovelli, Antonio

    The city of Benevento (Southern Italy) has been repeatedly struck by large historical earthquakes. A heterogeneous geologic structure and widespread soft soil conditions make the estimation of site effects crucial for the seismic hazard assessment of the city. From 2000 until 2004, we installed seismic stations to collect earthquake data over zones with different geological conditions. Despite the high level of urban noise, we recorded more than 150 earthquakes at twelve sites. This data set yields the first, well documented experimental evidence for weak to moderate local amplifications. We investigated site effects primarily by the classical spectral ratio technique (CSR) using a rock station placed on the Benevento hill as reference. All sites in the Calore river valley and in the eastern part of the Benevento hill show a moderate high-frequency (f > 4 Hz) amplification peak. Conversely, sites in the Sabato river valley share weak-to-moderate amplification in a wide frequency band (from 1-2 to 7-10 Hz), without evident frequency peaks. Application of no-reference-site techniques to earthquake and noise data confirms the results of the CSRs in the sites of the Calore river valley and of the eastern part of the Benevento hill, but fails in providing indications for site effects in the Sabato river valley, being the H/V ratios nearly flat. One-dimensional modeling indicates that the ground motion amplification can be essentially explained in terms of a vertically varying geologic structure. High-frequency narrow peaks are caused by the strong impedance contrast existing between near-surface soft deposits and stiff cemented conglomerates. Conversely, broad-band amplifications in the Sabato river valley are likely due to a more complex layering with weak impedance contrasts both in the shallow and deep structure of the valley.

  2. Detection of very long period solar free oscillations in ambient seismic array noise

    Science.gov (United States)

    Caton, R.; Pavlis, G. L.; Thomson, D. J.; Vernon, F.

    2017-12-01

    For nearly two decades long-period seismologists have been aware that the Earth's free oscillations are in a constant state of excitement, even in the absence of large earthquakes. This phenomenon is now called the "Earth's hum," and much research has been done to determine what generates this hum. Here we examine a hypothesis first put forward by Thomson et al. in 2007 that a portion of the hum's energy comes from the sun. They hypothesized that solar free oscillations couple into the solid Earth, likely through electromagnetic processes, and produce signals that are observable in the frequency domain. If this is true, then at least some measurement of helioseismic oscillations may be possible using relatively cheap, ground-based instruments rather than spacecraft. In this project we attempt to improve upon previous studies by producing spectra from seismic arrays, rather than a single station. We use data from two arrays: The Homestake Mine 3D array in Lead, SD, and the Pinyon Flats array, which has seismometers in boreholes drilled into bedrock. Both have exceptionally low noise levels at ultra long periods and show easily visible earth tides on horizontal component data filtered to below the microseism band. In the Homestake data, below 500 μHz we have found evidence of what we suggest may be closely spaced solar g-mode lines. Such modes are produced by a density inversion at the top of the solar core. There is no sign of these modes in the Pinyon Flats data, but we find this is likely due to the signal-to-noise ratio of those data, which is significantly lower than Homestake. Significance tests of bands below 500 μHz indicate with probability levels as high as 40σ that these lines are not the result of random processes. Critical examination of our processing steps for sources of bias indicate that the observed line structure is not a processing artifact.

  3. Association between ambient noise exposure and school performance of children living in an urban area: a cross-sectional population-based study.

    Science.gov (United States)

    Pujol, Sophie; Levain, Jean-Pierre; Houot, Hélène; Petit, Rémy; Berthillier, Marc; Defrance, Jérôme; Lardies, Joseph; Masselot, Cyril; Mauny, Frédéric

    2014-04-01

    Most of the studies investigating the effects of the external noise on children's school performance have concerned pupils in schools exposed to high levels due to aircraft or freeway traffic noise. However, little is known about the consequences of the chronic ambient noise exposure at a level commonly encountered in residential urban areas. This study aimed to assess the relationship between the school performance of 8- to 9-year-old-children living in an urban environment and their chronic ambient noise exposure at home and at school. The children's school performances on the national standardized assessment test in French and mathematics were compared with the environmental noise levels. Children's exposure to ambient noise was calculated in front of their bedrooms (Lden) and schools (LAeq,day) using noise prediction modeling. Questionnaires were distributed to the families to collect potential confounding factors. Among the 746 respondent children, 586 were included in multilevel analyses. On average, the LAeq,day at school was 51.5 dB (SD= 4.5 dB; range = 38-58 dB) and the outdoor Lden at home was 56.4 dB (SD= 4.4 dB; range = 44-69 dB). LAeq,day at school was associated with impaired mathematics score (p = 0.02) or impaired French score (p = 0.01). For a + 10 dB gap, the French and mathematics scores were on average lower by about 5.5 points. Lden at home was significantly associated with impaired French performance when considered alone (p school exposure was considered (p = 0.06). The magnitude of the observed effect on school performance may appear modest, but should be considered in light of the number of people who are potentially chronically exposed to similar environmental noise levels.

  4. Estimation of time varying system parameters from ambient response using improved Particle-Kalman filter with correlated noise

    Science.gov (United States)

    Sen, Subhamoy; Crinière, Antoine; Mevel, Laurent; Cerou, Frederic; Dumoulin, Jean

    2017-04-01

    within a PF environment that estimates the parameters. This facilitates employing relatively less expensive linear KF for linear state estimation problem while costly PF is employed only for parameter estimation. Additionally, the proposed algorithm also takes care of those systems for which system and measurement noises are not uncorrelated as it is commonly idealized in standard filtering algorithms. As an example, for mechanical systems under ambient vibration it happens when acceleration response is considered as measurement. Thus the process and measurement noise in these system descriptions are obviously correlated. For this, an improved description for the Kalman gain is developed. Further, to enhance the consistency of particle filtering based parameter estimation involving high dimensional parameter space, a new temporal evolution strategy for the particles is defined. This strategy aims at restricting the solution from diverging (up to the point of no return) because of an isolated event of infeasible estimation which is very much likely especially when dealing with high dimensional parameter space.

  5. Underwater laser imaging system (UWLIS)

    Energy Technology Data Exchange (ETDEWEB)

    DeLong, M. [Lawrence Livermore National Lab., CA (United States)

    1994-11-15

    Practical limitations with underwater imaging systems area reached when the noise in the back scattered radiation generated in the water between the imaging system and the target obscures the spatial contrast and resolution necessary for target discovery and identification. The advent of high power lasers operating in the blue-green portion of the visible spectrum (oceanic transmission window) has led to improved experimental illumination systems for underwater imaging. Range-gated and synchronously scanned devices take advantage of the unique temporal and spatial coherence properties of laser radiation, respectively, to overcome the deleterious effects of common volume back scatter.

  6. Crustal structure and Seismic Hazard studies in Nigeria from ambient noise and earthquakes

    Science.gov (United States)

    Kadiri, U. A.

    2016-12-01

    The crust, upper Mantle and seismic hazard studies have been carried out in Nigeria using noise and earthquake data. The data were acquired from stations in Nigeria and international Agencies. Firstly, known depths of sediments in the Lower Benue Trough (LBT) were collected from wells; Resonance frequency (Fo) and average shear-wave velocities (Vs) were then computed using Matlab. Secondly, average velocities were estimated from noise cross-correlation along seismic stations. Thirdly, the moho depths beneath Ife, Kaduna and Nsukka stations were estimated, as well as Vp/Vs ratio using 2009 earthquake with epicenter in Nigeria. Finally, Statistical and Probabilistic Seismic Hazard Assessment (PSHA) were used to compute seismic hazard parameters in Nigeria and its surroundings. The results showed that, soils on the LBT with average shear wave velocity of about 5684m/s would experience more amplification in case of an earthquake, compared to the basement complex in Nigeria. The Vs beneath the seismic stations in Nigeria were also estimated as 288m/s, 1019m/s, 940.6m/s and 255.02m/s in Ife, Nsukka, Awka, and Abakaliki respectively. The average velocity along the station paths was 4.5km/secs, and the Vp, Vs for depths 100-500km profile in parts of South West Nigeria increased from about 5.83-6.42Km/sec and 3.48-6.31km/s respectively with Vp/Vs ratio decreasing from 1.68 to 1.02. Statistical analysis revealed a trend of increasing earthquake occurrence along the Mid-Atlantic Ridge and tending to West African region. The analysis of PSHA shows the likelihood of earthquakes with different magnitudes occurring in Nigeria and other parts West Africa in future. This work is aimed at addressing critical issues regarding sites effect characterization, improved earthquake location and robust seismic hazards assessment for planning in the choice of sites for critical facilities in Nigeria. Keywords: Sediment thickness, Resonance Frequency, Average Velocity, Seismic Hazard, Nigeria

  7. Monitoring southwest Greenland’s ice sheet melt with ambient seismic noise

    Science.gov (United States)

    Mordret, Aurélien; Mikesell, T. Dylan; Harig, Christopher; Lipovsky, Bradley P.; Prieto, Germán A.

    2016-01-01

    The Greenland ice sheet presently accounts for ~70% of global ice sheet mass loss. Because this mass loss is associated with sea-level rise at a rate of 0.7 mm/year, the development of improved monitoring techniques to observe ongoing changes in ice sheet mass balance is of paramount concern. Spaceborne mass balance techniques are commonly used; however, they are inadequate for many purposes because of their low spatial and/or temporal resolution. We demonstrate that small variations in seismic wave speed in Earth’s crust, as measured with the correlation of seismic noise, may be used to infer seasonal ice sheet mass balance. Seasonal loading and unloading of glacial mass induces strain in the crust, and these strains then result in seismic velocity changes due to poroelastic processes. Our method provides a new and independent way of monitoring (in near real time) ice sheet mass balance, yielding new constraints on ice sheet evolution and its contribution to global sea-level changes. An increased number of seismic stations in the vicinity of ice sheets will enhance our ability to create detailed space-time records of ice mass variations. PMID:27386524

  8. Time-lapse imaging of fault properties at seismogenic depth using repeating earthquakes, active sources and seismic ambient noise

    Science.gov (United States)

    Cheng, Xin

    2009-12-01

    The time-varying stress field of fault systems at seismogenic depths plays the mort important role in controlling the sequencing and nucleation of seismic events. Using seismic observations from repeating earthquakes, controlled active sources and seismic ambient noise, five studies at four different fault systems across North America, Central Japan, North and mid-West China are presented to describe our efforts to measure such time dependent structural properties. Repeating and similar earthquakes are hunted and analyzed to study the post-seismic fault relaxation at the aftershock zone of the 1984 M 6.8 western Nagano and the 1976 M 7.8 Tangshan earthquakes. The lack of observed repeating earthquakes at western Nagano is attributed to the absence of a well developed weak fault zone, suggesting that the fault damage zone has been almost completely healed. In contrast, the high percentage of similar and repeating events found at Tangshan suggest the existence of mature fault zones characterized by stable creep under steady tectonic loading. At the Parkfield region of the San Andreas Fault, repeating earthquake clusters and chemical explosions are used to construct a scatterer migration image based on the observation of systematic temporal variations in the seismic waveforms across the occurrence time of the 2004 M 6 Parkfield earthquake. Coseismic fluid charge or discharge in fractures caused by the Parkfield earthquake is used to explain the observed seismic scattering properties change at depth. In the same region, a controlled source cross-well experiment conducted at SAFOD pilot and main holes documents two large excursions in the travel time required for a shear wave to travel through the rock along a fixed pathway shortly before two rupture events, suggesting that they may be related to pre-rupture stress induced changes in crack properties. At central China, a tomographic inversion based on the theory of seismic ambient noise and coda wave interferometry

  9. Ambient Noise Tomography at Regional and Local Scales in Southern California using Rayleigh Wave Phase Dispersion and Ellipticity

    Science.gov (United States)

    Berg, E.; Lin, F. C.; Qiu, H.; Wang, Y.; Allam, A. A.; Clayton, R. W.; Ben-Zion, Y.

    2017-12-01

    Rayleigh waves extracted from cross-correlations of ambient seismic noise have proven useful in imaging the shallow subsurface velocity structure. In contrast to phase velocities, which are sensitive to slightly deeper structure, Rayleigh wave ellipticity (H/V ratios) constrains the uppermost crust. We conduct Rayleigh wave ellipticity and phase dispersion measurements in Southern California between 6 and 18 second periods, computed from multi-component ambient noise cross-correlations using 315 stations across the region in 2015. Because of the complimentary sensitivity of phase velocity and H/V, this method enables simple and accurate resolution of near-surface geological features from the surface to 20km depth. We compare the observed H/V ratios and phase velocities to predictions generated from the current regional models (SCEC UCVM), finding strong correspondence where the near-surface structure is well-resolved by the models. This includes high H/V ratios in the LA Basin, Santa Barbara Basin and Salton Trough; and low ratios in the San Gabriel, San Jacinto and southern Sierra Nevada mountains. Disagreements in regions such as the Western Transverse Ranges, Salton Trough, San Jacinto and Elsinore fault zones motivate further work to improve the community models. A new updated 3D isotropic model of the area is derived via a joint inversion of Rayleigh phase dispersions and H/V ratios. Additionally, we examine azimuthal dependence of the H/V ratio to ascertain anisotropy patterns for each station. Clear 180º periodicity is observed for many stations suggesting strong shallow anisotropy across the region including up to 20% along the San Andreas fault, 15% along the San Jacinto Fault and 25% in the LA Basin. To better resolve basin structures, we apply similar techniques to three dense linear geophone arrays in the San Gabriel and San Bernardino basins. The three arrays are composed by 50-125 three-component 5Hz geophones deployed for one month each with 15-25km

  10. Time-Lapse Monitoring of an Engineering Scaled Excavation at Federal District, Brazil by Passive Ambient NoiseInterferometry

    Science.gov (United States)

    Cárdenas-Soto, M., Sr.; Hussain, Y.; Martinez-Carvajal, H., Sr.; Martino, S., Sr.; Rocha, M., Sr.

    2016-12-01

    Understanding the dynamics of stress relief mechanisms that lead to complete material collapse of unstable slopes is challenging. This research is focused on the novel use of Passive Ambient Noise Interferometry (PANI), a new technique that has revolutionized the seismology. In this technique the impulse response or Green function between two sensors is calculated by cross-correlation of the noise rescored at these stations. We applied PANI to monitor the deformational behavior of a prototype field experiment under semi controlled conditions for their use in landsliding early warning systems.The experimental setup consists of a 2 m engineering-scaled excavation,where induced failure was monitored by ambient vibrations propagating in tropical clayey deposits. The experimental setup consisted of dense network of 20 three components short period seismometers (Sercel L4C-3D) installed in three circular arrays with their distances from face of normal slope as 10, 20 and 30 meters, respectively.The frequency response of these seismometers is in range of 2-100 Hz. Recording was done in continuous mode at sampling rate of 1000 Hz with datalogger (RefTek DAS-130/3). Sensors were time synchronized by twenty 130 GPS/01. In this stage, the stress was applied on the one flank of this normal slope dug in the experimental field of University of Brasilia, by a hydraulic jack through a metallic plate. This incremental loading was kept on rising until the slope failure took place. This loading mechanism provided an opportunity to monitoring the changes in Rayleigh wave velocity before, during and after the complete failure. After initial processing, the green function (GF) or impulse response was calculated between each pair of sensors by cross correlation at time step of 4 second. All individual GFs, for entire monitoring period (30 minutes) were stacked to obtained a single reference GF. Stretching (dt/t) in waveform is calculated by subtracting individual GF from average GF, that

  11. Shallow structure of Deception Island, Antarctica, from correlations of ambient seismic noise on a set of dense seismic arrays

    Science.gov (United States)

    Luzón, F.; Almendros, J.; García-Jerez, A.

    2011-05-01

    We investigated the shallow velocity structure of Deception Island volcano, Antarctica, using correlations of ambient seismic noise. We selected long records of noise obtained by eight seismic arrays deployed along the inner coast of Deception during the period 2003-2005. Using these data, we calculated average dispersion curves and estimated local 1-D velocity models for the array sites. The combination of these profiles allowed us to obtain a comprehensive model of the shallow velocity structure of the island. The volcano is composed of relatively soft layers of pyroclastic deposits and sediments extending to a depth of about 400 m, with different degrees of compaction. Two layers with thicknesses of about 100 and 300 m and S-wave velocities of around 0.2-0.8 and 0.7-1.1 km s-1, respectively, can be differentiated. The deeper structure is highly variable in terms of wave velocities and layer depths. Although the resolving capabilities are reduced for these layers, the larger S-wave velocities in the range 1.3-2.8 km s-1 indicate that they can be associated with pre-caldera structures and products. There are substantial differences between the different models, which can be spatially related to heterogeneities in the volcano structure. The lowest S-wave velocities may be related to the alterations produced by hydrothermal activity near the surface. On the contrary, the largest velocities occur near the caldera border, revealing the presence of compact materials at shallow depths. Sharp lateral variations can also be observed in the northwest of the bay, which points to the presence of NW-SE faults and/or strong velocity gradients.

  12. Polarization Analysis of Ambient Seismic Noise Green's Functions for Monitoring Glacial State

    Science.gov (United States)

    Fry, B.; Horgan, H. J.; Levy, R. H.; Bertler, N. A. N.

    2017-12-01

    Analysis of continuously recorded background seismic noise has emerged as a powerful technique to monitor changes within the Earth. In a process analogous to Einstein's 'Brownian motion', seismic energy enters the Earth through a variety of mechanisms and then is dissipated through scattering processes or through a semi-random distribution of sources. Eventually, in stratified media, some of this energy assembles itself in coherent packets and propagates as seismic surface waves. Through careful analysis of these waves as recorded by two seismic stations over a short period of time, we can reconstruct Empirical Green's Functions (EGF). EGF are sensitive to the material through which the waves are travelling between the two stations. They can thus provide 4D estimates of material properties such as seismic velocity and anisotropy. We specifically analyze both the bulk velocity and the complex phase of these EGF to look for subtle changes in velocity with direction of propagation as well as the nature of particle polarization and ellipticity. These characteristics can then be used as a proxy for contemporaneous stress and strain or 'inherited' strain. Similar approaches have proven successful in mapping stresses and strain in the crust, on plate interface faults, volcanoes, and on glaciers and the Greenland ice sheet. We will present results from applying this approach to continuous broadband data recorded on the West Antarctic Ice Sheet through the Polenet project. Our results suggest that we can reconstruct EGF at least between frequencies of 300mHz and 50mHz for time periods, providing information about the contemporary state of ice and underlying lithosphere on a seasonal or annual basis. Our primary goals are determining glacial state by linking wave propagation to material fabric on micro (crystal orientation) and macro (strain marker) scales and well as rebound processes in the lithosphere during glacial loading and unloading. We will present our current

  13. VS of the uppermost crust structure of the Campi Flegrei caldera (southern Italy) from ambient noise Rayleigh wave analysis

    Science.gov (United States)

    Costanzo, M. R.; Nunziata, C.; Strollo, R.

    2017-11-01

    Shear wave velocities (VS) are defined in the uppermost 1-2 km of the Campi Flegrei caldera through the non-linear inversion of the group velocity dispersion curves of fundamental-mode Rayleigh waves extracted from ambient noise cross-correlations between two receivers. Noise recordings, three months long, at 12 seismic stations are cross-correlated between all couples of stations. The experiment provided successful results along 54 paths (inter-stations distance), of which 27 sampled a depth > 1 km. VS contour lines are drawn from 0.06 km b.s.l. to 1 km depth b.s.l. and show difference between the offshore (gulf of Pozzuoli and coastline) and the onshore areas. At 0.06 km b.s.l., the gulf of Pozzuoli and the coastline are characterized by VS of 0.3-0.5 km/s and of 0.5-0.7 km/s, respectively. Such velocities are typical of Neapolitan pyroclastic soils and fractured or altered tuffs. The inland shows VS in the range 0.7-0.9 km/s, typical of Neapolitan compact tuffs. Velocities increase with depth and, at 1 km depth b.s.l., velocities lower than 1.5 km/s are still present in the gulf and along the coastline while velocities higher than 1.9 km/s characterize the eastern sector (grossly coincident with the Neapolitan Yellow Tuff caldera rim), the S. Vito plain and the area between Solfatara and SW of Astroni. Such features are much more evident along two cross-sections drawn in the offshore and onshore sectors by integrating our VS models with literature data. Our models join previous noise cross-correlation studies at greater scale at depths of 0.7-0.8 km, hence the picture of the Campi Flegrei caldera is shown up to a depth of 15 km. VS of about 1.7 km/s, corresponding to compression velocities (VP) of about 3 km/s (computed by using the VP/VS ratio resulted in the inversion), are found at depths of 1.1 km, in the centre of the gulf of Pozzuoli, and at a depth of about 0.7 km b.s.l. onshore. An increment of VS velocity ( 1.9-2.0 km/s) is locally observed onshore

  14. Ambient Sensors

    NARCIS (Netherlands)

    Börner, Dirk; Specht, Marcus

    2014-01-01

    This software sketches comprise two custom-built ambient sensors, i.e. a noise and a movement sensor. Both sensors measure an ambient value and process the values to a color gradient (green > yellow > red). The sensors were built using the Processing 1.5.1 development environment. Available under

  15. The seismic wave speed structure of the Ontong Java Plateau determined from joint ambient noise and earthquake waveform data

    Science.gov (United States)

    Covellone, B. M.; Savage, B. K.; Shen, Y.

    2014-12-01

    The Ontong Java Plateau (OJP) represents the result of a significant event in the Earth's geologic history. Limited geophysical and geochemical data, as well as the plateau's relative isolation in the Pacific Ocean, have made interpretation of the modern day geologic structure and its 120 Ma formation history difficult. Here we present the highest resolution images to date of the wave speed structure of the OJP region. We use an iterative finite-frequency tomography methodology and a unique data set that combines empirical Green's functions extracted from ambient noise and earthquake waveforms. The uniqueness and combination of datasets allow us to best exploit the limited station distribution in the Pacific and image wave speed structures between 35 km and greater than 250 km into the Earth. We image a region of fast shear wave speeds, greater than 4.75 km/s, that extends to greater than 100 km beneath the plateau. The wave speeds are similar to as observed in cratonic environments and are consistent with a compositional anomaly likely a result of eclogite entrainment during the plateau's formation.

  16. Ambient Noise Tomography of Southern California Images Dipping San Andreas-Parallel Structure and Low-Velocity Salton Trough Mantle

    Science.gov (United States)

    Barak, S.; Klemperer, S. L.; Lawrence, J. F.

    2014-12-01

    Ambient noise tomography (ANT) images the entire crust but does not depend on the spatial and temporal distribution of events. Our ANT high-resolution 3D velocity model of southern California uses 849 broadband stations, vastly more than previous studies, and four years of data, 1997-1998, 2007, and 2011, chosen to include our own broadband Salton Seismic Imaging Project, a 40-station transect across the Salton Trough, as well as other campaign stations in both Mexico and the U.S.A., and permanent stations. Our shear-wave model has 0.05° x 0.05° lateral and 1 km vertical blocks. We used the Harvard Community Velocity Model (CVM-H) as the initial model for the inversion. We show significant differences relative to the CVM-H model, especially in the lower crust and upper mantle. We observe prominent low-velocity anomalies in the upper mantle under the Salton Buttes and Cerro Prieto geothermal fields, indicating high-temperatures and possibly partial-melt. Similar low-velocity zones have been previously observed along the Gulf of California. We also observe vertical to gradually dipping lateral velocity contrasts in the lower crust under the southern part of the San Andreas Fault. The east to northeast dip may represent crustal fabric sheared by movement of the Pacific plate under the North American plate prior to the initiation of transform motion.

  17. Near-bottom hydrophone measurements of ambient noise and sperm whale vocalizations in the northern Gulf of Mexico

    Science.gov (United States)

    Newcomb, Joal; Fisher, Robert; Field, Robert; Turgut, Altan; Ioup, George; Ioup, Juliette; Rayborn, Grayson; Kuczaj, Stan; Caruthers, Jerald; Goodman, Ralph; Sidorovskaia, Natalia

    2002-05-01

    Three bottom-moored hydrophones, 50 m above the bottom, were placed on a downslope line, ending at the largest concentration of sperm whale sightings in the northern Gulf of Mexico, in 600 m, 800 m, and 1000 m water depths. These depths were chosen after upslope propagation modeling, using historical databases, showed transmission losses greater than 110 dB at hydrophones near the bottom in water shallower than 600 m for a 500 m deep source at the 1000 m contour. These autonomously recording hydrophones were environmental acoustic recording system (EARS) buoys obtained from the Naval Oceanographic Office. They were capable of recording signals up to 5500 Hz continuously for 36 days and were deployed from July 17 through August 21. During this period a major marine mammal exercise was being conducted at the surface by the Minerals Management Service and the National Marine Fisheries Service, with other government and university scientists, in which temporary acoustic recording devices were attached to the whales and the whales were monitored by a surface towed array. Our near-bottom measurements of ambient noise and sperm whale vocalizations are discussed and compared to those surface and on-whale measurements. [Research supported by ONR.

  18. Crustal and uppermost mantle structure of southern Norway: results from surface wave analysis of ambient seismic noise and earthquake data

    Science.gov (United States)

    Köhler, Andreas; Weidle, Christian; Maupin, Valérie

    2012-12-01

    We use ambient seismic noise and earthquake recordings on a temporary regional network in southern Norway to produce Rayleigh and Love wave phase velocity maps from 3 to 67 s period. Local dispersion curves are then jointly inverted for a 3-D shear wave velocity model of the region. We perform a two-step inversion approach. First, a direct search, Monte Carlo algorithm is applied to find best fitting isotropic velocity depth profiles. Those profiles are then used as initial models for a linearised inversion which takes into account radial anisotropy in the shear wave structure. Results reveal crustal as well as uppermost mantle structures in the studied region. Velocity anomalies in the upper crust are rather small in amplitude and can in most parts be related to surface geology in terms of rock densities. Old tectonic units like the Oslo Graben (300-240 Ma) and the Caledonian nappes (440-410 Ma) are clearly imaged. Furthermore, we find clear indications for localized crustal anisotropy of about 3 per cent. Despite generally poor resolution of interface depths in surface wave inversion, we find lateral variation of crustal thickness in agreement with previous studies. We are able to confirm and locate the transition from a slow lithospheric upper mantle underneath southern Norway to a fast shield-like mantle towards Sweden.

  19. Time-Lapse Monitoring with 4D Seismic Coda Waves in Active, Passive and Ambient Noise Data

    Science.gov (United States)

    Lumley, D. E.; Kamei, R.; Saygin, E.; Shragge, J. C.

    2017-12-01

    The Earth's subsurface is continuously changing, due to temporal variations in fluid flow, stress, temperature, geomechanics and geochemistry, for example. These physical changes occur at broad tectonic and earthquake scales, and also at very detailed near-surface and reservoir scales. Changes in the physical states of the earth cause time-varying changes in the physical properties of rocks and fluids, which can be monitored with natural or manmade seismic waves. Time-lapse (4D) seismic monitoring is important for applications related to natural and induced seismicity, hydrocarbon and groundwater reservoir depletion, CO2 sequestration etc. An exciting new research area involves moving beyond traditional methods in order to use the full complex time-lapse scattered wavefield (4D coda waves) for both manmade active-source 3D/4D seismic data, and also to use continuous recordings of natural-source passive seismic data, especially (micro) earthquakes and ocean ambient noise. This research involves full wave-equation approaches including waveform inversion (FWI), interferometry, Large N sensor arrays, "big data" information theory, and high performance supercomputing (HPC). I will present high-level concepts and recent data results that are quite spectacular and highly encouraging.

  20. Three-dimensional S-wave velocity model of the Bohemian Massif from Bayesian ambient noise tomography

    Science.gov (United States)

    Valentová, Lubica; Gallovič, František; Maierová, Petra

    2017-10-01

    We perform two-step surface wave tomography of phase-velocity dispersion curves obtained by ambient noise cross-correlations in the Bohemian Massif. In the first step, the inter-station dispersion curves were inverted for each period (ranging between 4 and 20 s) separately into phase-velocity maps using 2D adjoint method. In the second step, we perform Bayesian inversion of the set of the phase-velocity maps into an S-wave velocity model. To sample the posterior probability density function, the parallel tempering algorithm is employed providing over 1 million models. From the model samples, not only mean model but also its uncertainty is determined to appraise the reliable features. The model is correlated with known main geologic structures of the Bohemian Massif. The uppermost low-velocity anomalies are in agreement with thick sedimentary basins. In deeper parts (4-20 km), the S-wave velocity anomalies correspond, in general, to main tectonic domains of the Bohemian Massif. The exception is a stable low-velocity body in the middle of the high-velocity Moldanubian domain and high-velocity body resembling a promontory of the Moldanubian into the Teplá-Barrandian domain. The most pronounced (high-velocity) anomaly is located beneath the Eger Rift that is a part of a Tertiary rift system across Europe.

  1. Experimental Assessment of Underwater Radiated Sound of Different Ship Types

    NARCIS (Netherlands)

    Jansen, H.W.; Jong, C.A.F. de

    2015-01-01

    The aim of the SONIC project is to develop tools to investigate and mitigate the effects of underwater noise generated by shipping. One way to study the contribution of shipping noise to the background noise in the seas is to produce shipping noise maps. The SONIC project delivers the required

  2. 4th Pacific Rim Underwater Acoustics Conference

    CERN Document Server

    Xu, Wen; Cheng, Qianliu; Zhao, Hangfang

    2016-01-01

    These proceedings are a collection of 16 selected scientific papers and reviews by distinguished international experts that were presented at the 4th Pacific Rim Underwater Acoustics Conference (PRUAC), held in Hangzhou, China in October 2013. The topics discussed at the conference include internal wave observation and prediction; environmental uncertainty and coupling to sound propagation; environmental noise and ocean dynamics; dynamic modeling in acoustic fields; acoustic tomography and ocean parameter estimation; time reversal and matched field processing; underwater acoustic localization and communication as well as measurement instrumentations and platforms. These proceedings provide insights into the latest developments in underwater acoustics, promoting the exchange of ideas for the benefit of future research.

  3. Empirical Green's tensor retrieved from ambient noise cross-correlations at The Geysers geothermal field, Northern California

    Science.gov (United States)

    Nayak, Avinash; Taira, Taka'aki; Dreger, Douglas S.; Gritto, Roland

    2018-04-01

    We retrieve empirical Green's functions in the frequency range (˜0.2-0.9 Hz) for interstation distances ranging from ˜1 to ˜30 km (˜0.22 to ˜6.5 times the wavelength) at The Geysers geothermal field, Northern California, from coherency of ambient seismic noise being recorded by a variety of sensors (broad-band, short-period surface and borehole sensors, and one accelerometer). The applied methodology preserves the intercomponent relative amplitudes of the nine-component Green's tensor that allows us to directly compare noise-derived Green's functions (NGFs) with normalized displacement waveforms of complete single-force synthetic Green's functions (SGFs) computed with various 1-D and 3-D velocity models using the frequency-wavenumber integration method and a 3-D finite-difference wave propagation method, respectively. These comparisons provide an effective means of evaluating the suitability of different velocity models to different regions of The Geysers, and assessing the quality of the sensors and the NGFs. In the T-Tangential, R-Radial, Z-Vertical reference frame, the TT, RR, RZ, ZR and ZZ components (first component: force direction, second component: response direction) of NGFs show clear surface waves and even body-wave phases for many station pairs. They are also broadly consistent in phase and intercomponent relative amplitudes with SGFs for the known local seismic velocity structure that was derived primarily from body-wave traveltime tomography, even at interstation distances less than one wavelength. We also find anomalous large amplitudes in TR, TZ, RT and ZT components of NGFs at small interstation distances (≲4 km) that can be attributed to ˜10°-30° sensor misalignments at many stations inferred from analysis of longer period teleseismic waveforms. After correcting for sensor misalignments, significant residual amplitudes in these components for some longer interstation distance (≳8 km) paths are better reproduced by the 3-D velocity

  4. Surface wave tomography across the Sorgenfrei-Tornquist Zone, SW Scandinavia, using ambient noise and earthquake data

    Science.gov (United States)

    Köhler, Andreas; Maupin, Valérie; Balling, Niels

    2015-10-01

    We produce a S-wave velocity model of the crust and upper mantle around the Sorgenfrei-Tornquist Zone, southern Scandinavia, by analysing ambient seismic noise and earthquake recordings on temporary and permanent regional network stations. In a first step, we perform tomographical inversion of surface wave dispersion data from seismic noise to obtain Rayleigh and Love wave phase-velocity maps from 3 to about 30 s period. Local dispersion curves are then combined with regionally averaged surface wave velocities from earthquake data measured between 15 and about 100 s period. Dispersion curves are jointly inverted for a 3-D model of the S-wave velocity and radial velocity anisotropy by using a combined Monte Carlo and linearized inversion approach. Results reveal significant crustal as well as uppermost mantle velocity variations at all depth levels. Upper crustal structural variations are mainly controlled by the thick sedimentary Danish Basin with both low S-wave velocities and high anisotropy. Despite of the known limited capability of surface wave inversion to constrain interface depths and model parameter trade-offs, obtained Moho depths are in good agreement with previous studies in the region. Marked crustal thinning is clearly revealed beneath the Danish Basin with a narrow transition to the thicker crust in Swedish shield areas. Despite very different crustal and morphological structures, Denmark and southern Norway both have similar well-defined upper-mantle low-velocity zones, interpreted as asthenosphere, starting a depth of about 100 km. Compared with southern Sweden, showing high upper-mantle velocities, characteristic for shields, velocities are reduced by 0.30-0.40 km s-1 (6-8 per cent) at the depth levels of 140-200 km and radial anisotropy of 2-4 per cent is observed. Our study confirms the importance of the Sorgenfrei-Tornquist Zone, as a very deep structural boundary, separating old, thick, cratonic Baltica lithosphere in southern Sweden from

  5. Ambient noise tomography reveals basalt and sub-basalt velocity structure beneath the Faroe Islands, North Atlantic

    Science.gov (United States)

    Sammarco, Carmelo; Cornwell, David G.; Rawlinson, Nicholas

    2017-11-01

    Ambient noise tomography is applied to seismic data recorded by a portable array of seismographs deployed throughout the Faroe Islands in an effort to illuminate basalt sequences of the North Atlantic Igneous Province, as well as underlying sedimentary layers and Precambrian basement. Rayleigh wave empirical Green's functions between all station pairs are extracted from the data via cross-correlation of long-term recordings, with phase weighted stacking implemented to boost signal-to-noise ratio. Dispersion analysis is applied to extract inter-station group travel-times in the period range 0.5-15 s, followed by inversion for period-dependent group velocity maps. Subsequent inversion for 3-D shear wave velocity reveals the presence of significant lateral heterogeneity (up to 25%) in the crust. Main features of the final model include: (i) a near-surface low velocity layer, interpreted to be the Malinstindur Formation, which comprises subaerial compound lava flows with a weathered upper surface; (ii) a sharp velocity increase at the base of the Malinstindur Formation, which may mark a transition to the underlying Beinisvørð Formation, a thick laterally extensive layer of subaerial basalt sheet lobes; (iii) a low velocity layer at 2.5-7.0 km depth beneath the Beinisvørð Formation, which is consistent with hyaloclastites of the Lopra Formation; (iv) an upper basement layer between depths of 5-9 km and characterized by S wave velocities of approximately 3.2 km/s, consistent with low-grade metamorphosed sedimentary rocks; (v) a high velocity basement, with S wave velocities in excess of 3.6 km/s. This likely reflects the presence of a crystalline mid-lower crust of Archaean continental origin. Compared to previous interpretations of the geological structure beneath the Faroe Islands, our new results point to a more structurally complex and laterally heterogeneous crust, and provide constraints which may help to understand how continental fragments are rifted from the

  6. A statistical assessment of seismic models of the U.S. continental crust using Bayesian inversion of ambient noise surface wave dispersion data

    Science.gov (United States)

    Olugboji, T. M.; Lekic, V.; McDonough, W.

    2017-07-01

    We present a new approach for evaluating existing crustal models using ambient noise data sets and its associated uncertainties. We use a transdimensional hierarchical Bayesian inversion approach to invert ambient noise surface wave phase dispersion maps for Love and Rayleigh waves using measurements obtained from Ekström (2014). Spatiospectral analysis shows that our results are comparable to a linear least squares inverse approach (except at higher harmonic degrees), but the procedure has additional advantages: (1) it yields an autoadaptive parameterization that follows Earth structure without making restricting assumptions on model resolution (regularization or damping) and data errors; (2) it can recover non-Gaussian phase velocity probability distributions while quantifying the sources of uncertainties in the data measurements and modeling procedure; and (3) it enables statistical assessments of different crustal models (e.g., CRUST1.0, LITHO1.0, and NACr14) using variable resolution residual and standard deviation maps estimated from the ensemble. These assessments show that in the stable old crust of the Archean, the misfits are statistically negligible, requiring no significant update to crustal models from the ambient noise data set. In other regions of the U.S., significant updates to regionalization and crustal structure are expected especially in the shallow sedimentary basins and the tectonically active regions, where the differences between model predictions and data are statistically significant.

  7. Structure of magma reservoirs beneath Merapi and surrounding volcanic centers of Central Java modeled from ambient noise tomography

    Science.gov (United States)

    Koulakov, Ivan; Maksotova, Gulzhamal; Jaxybulatov, Kayrly; Kasatkina, Ekaterina; Shapiro, Nikolai M.; Luehr, Birger-G.; El Khrepy, Sami; Al-Arifi, Nassir

    2016-10-01

    We present a three-dimensional model of the distribution of S-wave velocity in the upper crust to a depth of 20 km beneath Central Java based on the analysis of seismic ambient noise data recorded by more than 100 seismic stations in 2004 associated with the MERAMEX project. To invert the Rayleigh wave dispersion curves to construct 2-D group-velocity maps and 3-D distributions of S-wave velocity, we have used a new tomographic algorithm based on iterative linearized inversion. We have performed a series of synthetic tests that demonstrate significantly higher resolution in the upper crust with this model compared to the local earthquake travel-time tomography (LET) model previously applied for the same station network. Beneath the southern flank of Merapi, we identify a large low-velocity anomaly that can be split into two layers. The upper layer reflects the ˜1 km thick sedimentary cover of volcanoclastic deposits. The deeper anomaly at depths of ˜4-8 km may represent a magma reservoir with partially molten rock that feeds several volcanoes in Central Java. Beneath the Merapi summit, we observe another low-velocity anomaly as deep as 8 km that may be associated with the active magma reservoir that feeds the eruptive activity of Merapi. In the southern portion of the study area, in the lower crust, we identify a low-velocity anomaly that may represent the top of the pathways of volatiles and melts ascending from the slab that was previously inferred from the LET model results. We observe that this anomaly is clearly separate from the felsic magma reservoirs in the upper crust.

  8. Ambient noise tomography of the Cameroon Volcanic Line and Northern Congo craton: new constraints on the structure of the lithosphere

    Science.gov (United States)

    Guidarelli, M.; Aoudia, A.

    2016-03-01

    We investigate the lithospheric structure of Cameroon inverting Rayleigh waves obtained from the cross-correlation of ambient seismic noise. We correlate seismic records between 32 broad-band stations and we obtain good quality Rayleigh waves for 310 interstation paths. We measure group velocity dispersion curves from the reconstructed Rayleigh waves in the period range 10-35 s and we invert the group velocities for tomographic images. After the tomography the group velocities are then inverted, together with longer period group velocity measurements from existing literature, to compute a 3-D S-wave velocity model of the Cameroon lithosphere down to 100 km depth. Our results provide an unprecedented mapping of the physical properties of the different crustal units and their correlations with surface geology, as well as with mantle lithospheric variations. The Cameroon Volcanic Line (CVL) appears as a segmented feature exhibiting different physical properties along strike. The active Mt Cameroon volcano is underlain by very low velocities, unlike the other segments of the CVL. The along-strike variations in crustal structure suggest that lateral heterogeneities in lithospheric thickness and physical properties have influenced the location and distribution of magmatism. The crust beneath the Central African Shear Zone exhibits a sizeable low velocity anomaly. The lithosphere beneath Cameroon is characterised by a heterogeneous crust with a relatively constant thickness and a low velocity uppermost mantle at the edge of the Congo Craton. Our results favour processes combining small-scale upwelling at the edge of a thick lithosphere and reactivation of Precambrian basement structures to explain the distribution of Holocene-Recent magmatism and plateau uplift. Our results also indicate that Mt Cameroon and surroundings areas are the most at risk zones for magmatic activity during this stage of CVL development.

  9. Crustal structure beneath Liaoning province and the Bohai Sea and its adjacent region in China based on ambient noise tomography

    Science.gov (United States)

    Pang, Guang-hua; Feng, Ji-Kun; Lin, Jun

    2017-02-01

    The velocity structure of the crust beneath Liaoning province and the Bohai sea in China was imaged using ambient seismic noise recorded by 73 regional broadband stations. All available three-component time series from the 12-month span between January and December 2013 were cross-correlated to yield empirical Green's functions for Rayleigh and Love waves. Phase-velocity dispersion curves for the Rayleigh waves and the Love waves were measured by applying the frequency-time analysis method. Dispersion measurements of the Rayleigh wave and the Love wave were then utilized to construct 2D phase-velocity maps for the Rayleigh wave at 8-35 s periods and the Love wave at 9-32 s periods, respectively. Both Rayleigh and Love phase-velocity maps show significant lateral variations that are correlated well with known geological features and tectonics units in the study region. Next, phase dispersion curves of the Rayleigh wave and the Love wave extracted from each cell of the 2D Rayleigh wave and Love wave phase-velocity maps, respectively, were inverted simultaneously to determine the 3D shear wave velocity structures. The horizontal shear wave velocity images clearly and intuitively exhibit that the earthquake swarms in the Haicheng region and the Tangshan region are mainly clustered in the transition zone between the low- and high-velocity zones in the upper crust, coinciding with fault zones, and their distribution is very closely associated with these faults. The vertical shear wave velocity image reveals that the lower crust downward to the uppermost mantle is featured by distinctly high velocities, with even a high-velocity thinner layer existing at the bottom of the lower crust near Moho in central and northern the Bohai sea along the Tanlu fault, and these phenomena could be caused by the intrusion of mantle material, indicating the Tanlu fault could be just as the uprising channel of deep materials.

  10. Shear velocity model for the westernmost Mediterranean from ambient noise and ballistic finite-frequency Rayleigh wave tomography

    Science.gov (United States)

    Palomeras, I.; Villasenor, A.; Thurner, S.; Levander, A.; Gallart, J.; Harnafi, M.

    2014-12-01

    The westernmost Mediterranean comprises the Iberian Peninsula and Morocco, separated by the Alboran Sea and the Algerian Basin. From north to south this region consists of the Pyrenees, resulting from Iberia-Eurasia collision; the Iberian Massif, which has been undeformed since the end of the Paleozoic; the Central System and Iberian Chain, regions with intracontinental Oligocene-Miocene deformation; the Gibraltar Arc (Betics, Rif and Alboran terranes), resulting from post-Oligocene subduction roll-back; and the Atlas Mountains. We analyzed data from recent broad-band array deployments and permanent stations in the area (IberArray and Siberia arrays, the PICASSO array, the University of Munster array, and the Spanish, Portuguese and Moroccan National Networks) to characterize its lithospheric structure. The combined array of 350 stations has an average interstation spacing of ~60 km. We calculated the Rayleigh waves phase velocities from ambient noise (periods 4 to 40 s) and teleseismic events (periods 20 to 167 s). We inverted the phase velocities to obtain a shear velocity model for the lithosphere to ~200 km depth. Our results correlate well with the surface expression of the main structural units with higher crustal velocity for the Iberian Massif than for the Alpine Iberia and Atlas Mountains. The Gibraltar Arc has lower crustal shear velocities than the regional average at all crustal depths. It also shows an arc shaped anomaly with high upper mantle velocities (>4.6 km/s) at shallow depths (volcanic fields in Iberia and Morocco, indicative of high temperatures at relatively shallow depths, and suggesting that the lithosphere has been removed beneath these areas.

  11. Anisotropic full waveform ambient noise and earthquake tomography of the Ontong Java Plateau and surrounding Pacific upper mantle

    Science.gov (United States)

    Hirsch, A. C.; Savage, B.; Shen, Y.

    2017-12-01

    The Ontong Java (OJP) and Manihiki plateau (MP) large igneous provinces (LIP) of the Southwest Pacific took shape from a complicated, but poorly understood geological history. Unraveling the formation and deformation of these Pacific LIPs is not straightforward due to limited available data, remote location, and atypical geology. Origin hypotheses include melting of a plume or a fast-spreading triple junction, but distinguishing between these requires a further understanding of 120 Ma of deformation of each LIP. A previous tomographic model of OJP observed highly abnormal Rayleigh shear wave speeds, >4.75km/s, and attributed these to an unusual composition, garnet and clinopyroxene residual from melting pyroxenite entrained within a rising plume. Unfortunately, this model lacks constraints on the horizontally polarized shear wave speeds, SH or Love waves, anisotropy, and attenuation. We therefore perform a transverse-isotropic, scattering-integral, full-waveform tomography between periods of 25 and 200 seconds utilizing both ambient noise empirical Green's functions and seismic data from regional earthquakes. Our tomographic model improves upon previous work using permanent and temporary seismic stations, increased model space, and utilizing three components of seismic data (vertical, radial, and tangential). Included is also an assessment of the anelastic attenuation in the western Pacific using both surface waves and multiple core reflections. Our results will improve the tomographic resolution around OJP and the Pacific upper mantle between 35 and 300 km depth. This improved model will enhance our understanding of the tectonic history of the OJP and MP regions, and the Pacific Indo-Australian plate boundary.

  12. Surface wave group velocity in the Osaka sedimentary basin, Japan, estimated using ambient noise cross-correlation functions

    Science.gov (United States)

    Asano, Kimiyuki; Iwata, Tomotaka; Sekiguchi, Haruko; Somei, Kazuhiro; Miyakoshi, Ken; Aoi, Shin; Kunugi, Takashi

    2017-08-01

    Inter-station cross-correlation functions estimated using continuous ambient noise or microtremor records were used to extract the seismic wave propagation characteristics of the Osaka sedimentary basin, Japan. Temporary continuous observations were conducted at 15 sites in the Osaka basin between 2011 and 2013. The data were analyzed using seismic interferometry. The target period range was 2-8 s. Cross-correlations between all of the possible station pairs were calculated and stacked to produce a year-long data set, and Rayleigh wave signals in the vertical and radial components and Love wave signals in the transverse component were identified from the results. Simulation of inter-station Green's functions using the finite difference method was conducted to check the performance of the current three-dimensional velocity structure model. The measured time lag between the observed and theoretical Green's functions was less than 2 s for most station pairs, which is less than the wave period of interest in the target frequency range. Group velocity tomography was applied to group delay times estimated by means of multiple filter analysis. The estimated group velocities for longer periods of 5-8 s exhibited spatial variation within the basin, which is consistent with the bedrock depth distribution; however, the group velocities for shorter periods of 2-3 s were almost constant over the studied area. The waveform and group velocity information obtained by seismic interferometry analysis can be useful for future reconstruction of a three-dimensional velocity structure model in the Osaka basin.[Figure not available: see fulltext.

  13. Installation of the light tight cover for the SSD modules (the modules are behind the aluminium plate). The silicon sensors are sensitive to light tight, so ambient light will increase the noise and may even damage them.

    CERN Multimedia

    Nooren, G.

    2004-01-01

    Installation of the light tight cover for the SSD modules (the modules are behind the aluminium plate). The silicon sensors are sensitive to light tight , so ambient light will increase the noise and may even damage them.

  14. Correlações entre ruído ambiental em sala de aula e voz do professor Correlations between classroom environmental noise and teachers' voice

    Directory of Open Access Journals (Sweden)

    Rafaela Fernanda Guidini

    2012-12-01

    Full Text Available OBJETIVO: Identificar se existe correlação entre ruído ambiental no interior da sala de aula, intensidade da voz e presença de alteração vocal em professores. MÉTODOS: Foi realizada medição do ruído ambiental em dez salas de escolas municipais de ensino fundamental. A intensidade das vozes das professoras foi medida durante atividade de ensino. Amostras de vogal prolongada [é] e contagem de 1 a 20 emitidas pelas professoras foram analisadas utilizando escala GRBASI. Os resultados obtidos foram correlacionados. RESULTADOS: A média de ruído ambiental sem a presença das crianças em sala de aula variou de 40 a 51 dB(A e com a presença das crianças de 45 a 65 dB(A. Entre as professoras, houve 70% de ocorrência de vozes alteradas no grau geral (G e 90% com tensão na voz (S, variando entre graus discreto e moderado. Constatou-se variação entre 52 dB(A e 68 dB(A na intensidade da voz das professoras, atingindo 7,48 dB(A acima do nível do ruído ambiental. Houve correlação entre a intensidade vocal das professoras e ruído ambiental na presença das crianças durante a aula. CONCLUSÃO: Os níveis de ruído ambiental em sala de aula são altos e se correlacionam com o aumento da intensidade das vozes das professoras. Embora com alta ocorrência de vozes alteradas, não é possível correlacioná-las com o nível de ruído ambiental.PURPOSE: To explore the existence of correlations between environmental noise in classrooms, voice intensity and teacher's vocal problems. METHODS: Environmental noise was measured in 10 classrooms of municipal elementary schools; the intensity of teachers' voice was measured during teaching practice; teachers' speech samples containing emissions of sustained vowel [é] and counting from 1 to 20 were analyzed using the GRBASI protocol; and the results were tested for correlation. RESULTS: The average of environmental noise varied from 40 to 51 dB(A without the presence of children in the classroom, and

  15. Underwater Hearing in Turtles.

    Science.gov (United States)

    Willis, Katie L

    2016-01-01

    The hearing of turtles is poorly understood compared with the other reptiles. Although the mechanism of transduction of sound into a neural signal via hair cells has been described in detail, the rest of the auditory system is largely a black box. What is known is that turtles have higher hearing thresholds than other reptiles, with best frequencies around 500 Hz. They also have lower underwater hearing thresholds than those in air, owing to resonance of the middle ear cavity. Further studies demonstrated that all families of turtles and tortoises share a common middle ear cavity morphology, with scaling best suited to underwater hearing. This supports an aquatic origin of the group. Because turtles hear best under water, it is important to examine their vulnerability to anthropogenic noise. However, the lack of basic data makes such experiments difficult because only a few species of turtles have published audiograms. There are also almost no behavioral data available (understandable due to training difficulties). Finally, few studies show what kinds of sounds are behaviorally relevant. One notable paper revealed that the Australian snake-necked turtle (Chelodina oblonga) has a vocal repertoire in air, at the interface, and under water. Findings like these suggest that there is more to the turtle aquatic auditory scene than previously thought.

  16. Long-term exposure to road traffic noise, ambient air pollution, and cardiovascular risk factors in the HUNT and lifelines cohorts.

    Science.gov (United States)

    Cai, Yutong; Hansell, Anna L; Blangiardo, Marta; Burton, Paul R; de Hoogh, Kees; Doiron, Dany; Fortier, Isabel; Gulliver, John; Hveem, Kristian; Mbatchou, Stéphane; Morley, David W; Stolk, Ronald P; Zijlema, Wilma L; Elliott, Paul; Hodgson, Susan

    2017-08-01

    Blood biochemistry may provide information on associations between road traffic noise, air pollution, and cardiovascular disease risk. We evaluated this in two large European cohorts (HUNT3, Lifelines). Road traffic noise exposure was modelled for 2009 using a simplified version of the Common Noise Assessment Methods in Europe (CNOSSOS-EU). Annual ambient air pollution (PM10, NO2) at residence was estimated for 2007 using a Land Use Regression model. The statistical platform DataSHIELD was used to pool data from 144 082 participants aged ≥20 years to enable individual-level analysis. Generalized linear models were fitted to assess cross-sectional associations between pollutants and high-sensitivity C-reactive protein (hsCRP), blood lipids and for (Lifelines only) fasting blood glucose, for samples taken during recruitment in 2006-2013. Pooling both cohorts, an inter-quartile range (IQR) higher day-time noise (5.1 dB(A)) was associated with 1.1% [95% confidence interval (95% CI: 0.02-2.2%)] higher hsCRP, 0.7% (95% CI: 0.3-1.1%) higher triglycerides, and 0.5% (95% CI: 0.3-0.7%) higher high-density lipoprotein (HDL); only the association with HDL was robust to adjustment for air pollution. An IQR higher PM10 (2.0 µg/m3) or NO2 (7.4 µg/m3) was associated with higher triglycerides (1.9%, 95% CI: 1.5-2.4% and 2.2%, 95% CI: 1.6-2.7%), independent of adjustment for noise. Additionally for NO2, a significant association with hsCRP (1.9%, 95% CI: 0.5-3.3%) was seen. In Lifelines, an IQR higher noise (4.2 dB(A)) and PM10 (2.4 µg/m3) was associated with 0.2% (95% CI: 0.1-0.3%) and 0.6% (95% CI: 0.4-0.7%) higher fasting glucose respectively, with both remaining robust to adjustment for air/noise pollution. Long-term exposures to road traffic noise and ambient air pollution were associated with blood biochemistry, providing a possible link between road traffic noise/air pollution and cardio-metabolic disease risk. Published on behalf of the European Society of

  17. Underwater manipulator

    Science.gov (United States)

    Schrum, P.B.; Cohen, G.H.

    1993-04-20

    Self-contained, waterproof, water-submersible, remote-controlled apparatus is described for manipulating a device, such as an ultrasonic transducer for measuring crack propagation on an underwater specimen undergoing shock testing. The subject manipulator includes metal bellows for transmittal of angular motions without the use of rotating shaft seals or O-rings. Inside the manipulator, a first stepper motor controls angular movement. In the preferred embodiment, the bellows permit the first stepper motor to move an ultrasonic transducer [plus minus]45 degrees in a first plane and a second bellows permit a second stepper motor to move the transducer [plus minus]10 degrees in a second plane orthogonal to the first. In addition, an XY motor-driven table provides XY motion.

  18. Underwater manipulator

    International Nuclear Information System (INIS)

    Schrum, P.B.; Cohen, G.H.

    1993-01-01

    Self-contained, waterproof, water-submersible, remote-controlled apparatus is described for manipulating a device, such as an ultrasonic transducer for measuring crack propagation on an underwater specimen undergoing shock testing. The subject manipulator includes metal bellows for transmittal of angular motions without the use of rotating shaft seals or O-rings. Inside the manipulator, a first stepper motor controls angular movement. In the preferred embodiment, the bellows permit the first stepper motor to move an ultrasonic transducer ±45 degrees in a first plane and a second bellows permit a second stepper motor to move the transducer ±10 degrees in a second plane orthogonal to the first. In addition, an XY motor-driven table provides XY motion

  19. 3D structures of crust and uppermost mantle and azimuthal anisotropy in Tibet and surrounding regions from ambient noise tomography

    Science.gov (United States)

    Yang, Y.; Zheng, Y.; Ritzwoller, M. H.

    2010-12-01

    Tibet is our planet’s natural laboratory for studying how continents interact and deform in response to the collision between the Indian and the Eurasian plates. Although numerous seismic studies of Tibet have been performed, there remain fundamental disagreements in first-order questions about crustal deformation; e.g., whether the crust deforms coherently vertically or is perhaps coupled to the mantle. The reason is that existing models either do not model the crust effectively or only model the crust beneath parts of Tibet due to limitations in the distribution of seismic stations. In this study, we have applied ambient noise tomography (ANT) to data from FDSN stations, several temporary US PASSCAL installations and the Chinese provincial networks in and around Tibet during 2003 to 2009. Inter-station Rayleigh wave dispersion curves are measured from cross correlations of vertical components. These dispersion measurements are used to invert for isotropic phase velocity maps and azimuthal anisotropy of Rayleigh waves. Major basins, including Tarim, Qadaim and Sichuan, are all well delineated by slow phase velocities at short periods (8-15 sec). Crustal thinning from Tibet to the surrounding regions is manifest as a phase velocity increase at periods from 25 to 40 sec. Resulting phase velocity maps are further inverted for 3D Vs structures of crust and uppermost mantle. Low velocities are observed across most of the Tibetan Plateau at the depth range of 20-50 km. In southeastern Tibet, low velocities extend to the Yunnan Plateau while, in northeastern Tibet, low velocities are confined to the Plateau region and there is no low velocity existing beneath the Qingling Orogen between the Ordos Block and the Sichuan Basin in the crust and uppermost mantle. Prominent high velocities are observed in the middle and lower crust and in the uppermost mantle beneath the Tarim Basin, the Ordos Block and the Sichuan Basin. Patterns of Rayleigh wave azimuthal anisotropy at

  20. Preliminary Results From the CAUGHT Experiment: Investigation of the North Central Andes Subsurface Using Receiver Functions and Ambient Noise Tomography

    Science.gov (United States)

    Ryan, J. C.; Ward, K. M.; Porter, R. C.; Beck, S. L.; Zandt, G.; Wagner, L. S.; Minaya, E.; Tavera, H.

    2011-12-01

    Altiplano and portions of the Eastern Cordillera, and at approximately 40 under the sub-Andes and westernmost edge of the Beni basin. Unlike previous studies farther south, we do not see an increased crustal thickness beneath the Eastern Cordillera. The CAUGHT station coverage is also ideal for Ambient Noise Tomography (ANT) to investigate the seismic shear wave velocities in the upper crust (<30 km depth). ANT will be used to estimate the depth of basins in the northern Altiplano, and aid in constraining the upper crustal shear wave velocities for improved migration of receiver functions to depth. McQuarrie, N., Barnes, J., and Ehlers, T.A., 2008, Geometric, kinematic and erosional history of the central Andean Plateau (15-17°S), northern Bolivia: Tectonics, v. 27, TC3007, doi:10.1029/2006TC002054.

  1. Long-termexposure to road traffic noise, ambient air pollution, and cardiovascular risk factors in the HUNT and lifelines cohorts

    NARCIS (Netherlands)

    Cai, Yutong; Hansell, Anna L.; Blangiardo, Marta; Burton, Paul R.; de Hoogh, Kees; Doiron, Dany; Fortier, Isabel; Gulliver, John; Hveem, Kristian; Mbatchou, Stéphane; Morley, DavidW.; Stolk, Ronald P.; Zijlema, Wilma L.; Elliott, Paul; Hodgson, Susan

    2017-01-01

    Aims: Blood biochemistry may provide information on associations between road traffic noise, air pollution, and cardiovascular disease risk. We evaluated this in two large European cohorts (HUNT3, Lifelines). Methods and results: Road traffic noise exposure was modelled for 2009 using a simplified

  2. The Effects of Ambient Shipping Noise on the Performance of Single and Multiple Channel Moment Detectors for Unknown Transient Signals

    National Research Council Canada - National Science Library

    Pflug, Lisa

    1998-01-01

    ...) detector in both the Gaussian noise and the measured noise. Although the application of one-dimensional passband filters before the moment calculations improves the performance of all three detectors, it induces additional detection gain for the higher order moment detectors.

  3. A Novel Fractional Fourier Transform-Based ASK-OFDM System for Underwater Acoustic Communications

    Directory of Open Access Journals (Sweden)

    Rami Ashri

    2017-12-01

    Full Text Available A key research area in wireless transmission is underwater communications. It has a vital role in applications such as underwater sensor networks (UWSNs and disaster detection. The underwater channel is very unique as compared to other alternatives of transmission channels. It is characterized by path loss, multipath fading, Doppler spread and ambient noise. Thus, the bit error rate (BER is increased to a large extent when compared to its counterpart of cellular communications. Acoustic signals are the current best solution for underwater communications. The use of electromagnetic or optical waves obviously entails a much higher data rate. However, they suffer from high attenuation, absorption or scattering. This paper proposes a novel fractional fast Fourier transform (FrFT—orthogonal frequency division multiplexing (FrFT-OFDM system for underwater acoustic (UWA communication—which employs the amplitude shift keying (ASK modulation technique (FrFT-ASK-OFDM. Specifically, ASK achieves a better bandwidth efficiency as compared to other commonly used modulation techniques, such as quadrature amplitude modulation (QAM and phase shift keying (PSK. In particular, the system proposed in this article can achieve a very promising BER performance, and can reach higher data rates when compared to other systems proposed in the literature. The BER performance of the proposed system is evaluated numerically, and is compared to the corresponding M-ary QAM system in the UWA channel for the same channel conditions. Moreover, the performance of the proposed system is compared to the conventional fast Fourier transform (FFT-OFDM (FFT-OFDM system in the absence and presence of the effect of carrier frequency offset (CFO. Numerical results show that the proposed system outperforms the conventional FFT-based systems for UWA channels, even in channels dominated by CFO. Moreover, the spectral efficiency and data rate of the proposed system are approximately double

  4. Underwater Sound Reference Division

    Data.gov (United States)

    Federal Laboratory Consortium — The Underwater Sound Reference Division (USRD) serves as the U.S. standardizing activity in the area of underwater acoustic measurements, as the National Institute...

  5. Intérvalo unitario de tiempo de medición para ruido ambiental Unit timing for environmental noise measurements

    Directory of Open Access Journals (Sweden)

    William A. Giraldo A.

    2011-01-01

    Full Text Available En las entidades ambientales, los encargados de las mediciones de ruido ambiental y en general todas las personas que de una u otra forma han trabajado en esta temática, en algún momento se han puesto a pensar sobre la representatividad del tiempo unitario de muestreo y la forma de realizar evaluaciones para dar cumplimiento con dicho tiempo, sin que se aumenten considerablemente los costos de medición. En este artículo se plantea una metodología para determinar cómo un intervalo de cierta duración -en este caso, quince (15 minutos- para el muestreo del nivel de presión sonora es representativo para el período de una (1 hora, logrando de esta manera optimizar el uso de los sonómetros "fijos" y proponiendo una estrategia para reducir los costos en las mediciones de ruido ambiental y en general la elaboración de mapas de ruido.The managers of environmental noise measurements in environmental control agencies, or in general every person that work in this subject, have to think on the representativity of the unit measurement time interval, and how to evaluate it in order to get good quality results regarding the unit measurement time without increasing the measurement costs. A methodology for deciding if a certain measuring time interval -in this case, fifteen (15 minutes- is representative of noise pressure levels occurring during one hour, is proposed in this paper. This methodology allows to optimize the use of stationary sound level meters and to propose a strategy for reducing the costs of environmental noise measurements and of the designing of noise maps in general.

  6. Underwater Ambient Noise. Proceedings of a Conference Held at SACLANTCEN on 11-14 May 1982. Volume 2. Unclassified Papers. Part 1

    Science.gov (United States)

    1982-06-15

    un traitement a bord de la bouee. Pour le reste, ayant retenu une gamme de frequences relativement etendue (20 Hz - 20 kHz) et des fil- tres...qui fait I’objet du programme. La presentation des resultats est delivree sous de nombreuses formes. Les principales sont : - tableau ...Copenhagen FRANCE Bienvenu, G. Thomson-CSF Cagnes-sur-Mer de Raigniac, B. Societe AERO Paris Laval, R. Societe AERO Paris Lucas, GERDSM

  7. First to Flush: The Effects of Ambient Noise on Songbird Flight Initiation Distances and Implications for Human Experiences with Nature

    Directory of Open Access Journals (Sweden)

    Alissa R. Petrelli

    2017-06-01

    Full Text Available Throughout the world, birds represent the primary type of wildlife that people experience on a daily basis. However, a growing body of evidence suggests that alterations to the acoustic environment can negatively affect birds as well as humans in a variety of ways, and altered acoustics from noise pollution has the potential to influence human interactions with wild birds. Birds respond to approaching humans in a manner analogous to approaching predators, but the context of the interaction can also greatly influence the distance at which a bird initiates flight or escape behavior (i.e., flight initiation distance or FID. Here, we hypothesized that reliance on different sensory modalities to balance foraging and threat detection can influence how birds respond to approaching threats in the presence of background noise. We surveyed 12 songbird species in California and Wyoming and categorized each species into one of three foraging guilds: ground foragers, canopy gleaners, and hawking flycatchers and predicted FIDs to decrease, remain the same and increase with noise exposure, respectively. Contrary to expectations, the canopy gleaning and flycatching guilds exhibited mixed responses, with some species exhibiting unchanged FIDs with noise while others exhibited increased FIDs with noise. However, FIDs of all ground foraging species and one canopy gleaner decreased with noise levels. Additionally, we found no evidence of phylogenetic structure among species' mean FID responses and only weak phylogenetic structure for the relationship between FIDs and noise levels. Although our results provide mixed support for foraging strategy as a predictor of bird response to noise, our finding that most of the species we surveyed have shorter FIDs with increases in noise levels suggest that human observers may be able to approach ground foraging species more closely under noisy conditions. From an ecological perspective, however, it remains unclear whether

  8. Imaging San Jacinto Fault damage zone structure using dense linear arrays: application of ambient noise tomography, Rayleigh wave ellipticity, and site amplification

    Science.gov (United States)

    Wang, Y.; Lin, F. C.; Allam, A. A.; Ben-Zion, Y.

    2017-12-01

    The San Jacinto fault is presently the most seismically active component of the San Andreas Transform system in Southern California. To study the damage zone structure, two dense linear geophone arrays (BS and RR) were deployed across the Clark segment of the San Jacinto Fault between Anza and Hemet during winter 2015 and Fall 2016, respectively. Both arrays were 2 km long with 20 m station spacing. Month-long three-component ambient seismic noise data were recorded and used to calculate multi-channel cross-correlation functions. All three-component noise records of each array were normalized simultaneously to retain relative amplitude information between different stations and different components. We observed clear Rayleigh waves and Love waves on the cross-correlations of both arrays at 0.3 - 1 s period. The phase travel times of the Rayleigh waves on both arrays were measured by frequency-time analysis (FTAN), and inverted for Rayleigh wave phase velocity profiles of the upper 500 m depth. For both arrays, we observe prominent asymmetric low velocity zones which narrow with depth. At the BS array near the Hemet Stepover, an approximately 250m wide slow zone is observed to be offset by 75m to the northeast of the surface fault trace. At the RR array near the Anza segment of the fault, a similar low velocity zone width and offset are observed, along with a 10% across-fault velocity contrast. Analyses of Rayleigh wave ellipticity (H/V ratio), Love wave phase travel times, and site amplification are in progress. By using multiple measurements from ambient noise cross-correlations, we can obtain strong constraints on the local damage zone structure of the San Jacinto Fault. The results contribute to improved understanding of rupture directivity, maximum earthquake magnitude and more generally seismic hazard associated with the San Jacinto fault zone.

  9. Depth and sharpness variations of 410-km and 660-km discontinuities in North China Craton from dense array ambient noise interferometry

    Science.gov (United States)

    Yao, H.; Feng, J.; Poli, P.; Fang, L.; Wu, Y.

    2017-12-01

    Recent studies have demonstrated that body waves between pairs of stations can be successfully retrieved from ambient noise cross-correlation at both regional and global scales, although surface waves are the dominant signals. However, it is still difficult to use these retrieved body wave signals to map lateral depth variations of main structural discontinuities or velocity contrasts because of its low signal to noise ratio (SNR). In this research, based on a dense seismic array in eastern North China Craton, reflected P-wave signals from 410-km and 660-km discontinuities can be successfully recovered from ambient noise cross-correlation. To improve SNR of the reflected phases, the cross-correlations are stacked within each bin with the phase-weighted stack (PWS) method. In addition, there exist apparent spatial variations of the relative amplitude ratios between the reflected P410P and P660P phases. The retrieved P410P and P660P phases from stacked correlations reveal lateral variations of both depths and sharpness of the 410-km and 660-km discontinuities along two profiles, which may be related with hot material upwelling and the effect of stagnant Pacific plate in the transition zone beneath North China Craton. The imaging results are generally consistent with the results from teleseismic receiver functions, which demonstrate the possibility of mapping high-resolution topography and sharpness of deep internal discontinuities without earthquake-station geometric limitations. Future joint imaging with both interferometric and passive signals will be better for understanding interface architectures and related dynamic processes of the Earth.

  10. Seismic structure of the upper crust in the Albertine Rift from travel-time and ambient-noise tomography - a comparison

    Science.gov (United States)

    Jakovlev, Andrey; Kaviani, Ayoub; Ruempker, Georg

    2017-04-01

    Here we present results of the investigation of the upper crust in the Albertine rift around the Rwenzori Mountains. We use a data set collected from a temporary network of 33 broadband stations operated by the RiftLink research group between September 2009 and August 2011. During this period, 82639 P-wave and 73408 S-wave travel times from 12419 local and regional earthquakes were registered. This presents a very rare opportunity to apply both local travel-time and ambient-noise tomography to analyze data from the same network. For the local travel-time tomographic inversion the LOTOS algorithm (Koulakov, 2009) was used. The algorithm performs iterative simultaneous inversions for 3D models of P- and S-velocity anomalies in combination with earthquake locations and origin times. 28955 P- and S-wave picks from 2769 local earthquakes were used. To estimate the resolution and stability of the results a number of the synthetic and real data tests were performed. To perform the ambient noise tomography we use the following procedure. First, we follow the standard procedure described by Bensen et al. (2007) as modified by Boué et al. (2014) to compute the vertical component cross-correlation functions between all pairs of stations. We also adapted the algorithm introduced by Boué et al. (2014) and use the WHISPER software package (Briand et al., 2013) to preprocess individual daily vertical-component waveforms. On the next step, for each period, we use the method of Barmin et al. (2001) to invert the dispersion measurements along each path for group velocity tomographic maps. Finally, we adapt a modified version of the algorithm suggested by Macquet et al. (2014) to invert the group velocity maps for shear velocity structure. We apply several tests, which show that the best resolution is obtained at a period of 8 seconds, which correspond to a depth of approximately 6 km. Models of the seismic structure obtained by the two methods agree well at shallow depth of about

  11. Joint inversion of teleseismic P waveforms and surface-wave group velocities from ambient seismic noise in the Bohemian Massif

    Czech Academy of Sciences Publication Activity Database

    Růžek, Bohuslav; Plomerová, Jaroslava; Babuška, Vladislav

    2012-01-01

    Roč. 56, č. 1 (2012), s. 107-140 ISSN 0039-3169 R&D Projects: GA ČR GA205/07/1088; GA AV ČR IAA300120709; GA MŠk LM2010008 Institutional research plan: CEZ:AV0Z30120515 Keywords : receiver function * seismic noise * joint inversion * Bohemian Massif * velocity structure Subject RIV: DC - Siesmology, Volcanology, Earth Structure Impact factor: 0.975, year: 2012

  12. Thermal conductivity of silver loaded conductive epoxy from cryogenic to ambient temperature and its application for precision cryogenic noise measurements

    Science.gov (United States)

    Amils, Ricardo I.; Gallego, Juan Daniel; Sebastián, José Luis; Muñoz, Sagrario; Martín, Agustín; Leuther, Arnulf

    2016-06-01

    The pressure to increase the sensitivity of instrumentation has pushed the use of cryogenic Low Noise Amplifier (LNA) technology into a growing number of fields. These areas range from radio astronomy and deep space communications to fundamental physics. In this context manufacturing for cryogenic environments requires a proper thermal knowledge of the materials to be able to achieve adequate design behavior. In this work, we present experimental measurements of the thermal conductivity of a silver filled conductive epoxy (EPO-TEK H20E) which is widely used in cryogenic electronics applications. The characterization has been made using a sample preparation which mimics the practical use of this adhesive in the fabrication of cryogenic devices. We apply the data obtained to a detailed analysis of the effects of the conductive epoxy in a monolithic thermal noise source used for high accuracy cryogenic microwave noise measurements. In this application the epoxy plays a fundamental role since its limited thermal conductivity allows heating the chip with relatively low power. To our knowledge, the cryogenic thermal conductivity data of this epoxy has not been reported before in the literature in the 4-300 K temperature range. A second non-conductive epoxy (Gray Scotch-Weld 2216 B/A), also widely used in cryogenic applications, has been measured in order to validate the method by comparing with previous published data.

  13. Minimizing noise in fiberglass aquaculture tanks: Noise reduction potential of various retrofits

    Science.gov (United States)

    Equipment used in intensive aquaculture systems, such as pumps and blowers can produce underwater sound levels and frequencies within the range of fish hearing. The impacts of underwater noise on fish are not well known, but limited research suggests that subjecting fish to noise could result in imp...

  14. Simulation and Characteristics Analysis on Vibration and Sound Radiation Response for a Small Underwater Robot

    Directory of Open Access Journals (Sweden)

    Zhou Zhi

    2016-01-01

    Full Text Available An underwater robot is one of the important ocean equipment, and especially its stealth performance has influenced on the vitality in naval warfare. Structure radiation noise as the main source of underwater robot noise, so analysis on vibration and noise radiation is a topic of great concern. The way is used widely that based on fluid-solid coupling modal analysis combined with simulation on vibration and noise-radiation response in order to evaluate stealth performance of underwater structure. In the paper, firstly via finite element method and boundary element method, the modal frequencies and vibration modes of small underwater robot are calculated. Then the surface vibration displacements of underwater robot and the sound pressures of acoustic field under different frequency horizontal exciting force are obtained and analyzed. Lastly, through the analysis of the structural vibration and acoustic performance, the control strategies for structure bending vibration, acoustic radiation and structural acoustic design are proposed.

  15. Underwater Geotechnical Foundations

    National Research Council Canada - National Science Library

    Lee, Landris

    2001-01-01

    This report provides an overview and description of the design and construction of underwater geotechnical foundations and offers preliminary guidance based on past and current technology applications...

  16. Antarctic ice sheet thickness estimation using the horizontal-to-vertical spectral ratio method with single-station seismic ambient noise

    Science.gov (United States)

    Yan, Peng; Li, Zhiwei; Li, Fei; Yang, Yuande; Hao, Weifeng; Bao, Feng

    2018-03-01

    We report on a successful application of the horizontal-to-vertical spectral ratio (H / V) method, generally used to investigate the subsurface velocity structures of the shallow crust, to estimate the Antarctic ice sheet thickness for the first time. Using three-component, five-day long, seismic ambient noise records gathered from more than 60 temporary seismic stations located on the Antarctic ice sheet, the ice thickness measured at each station has comparable accuracy to the Bedmap2 database. Preliminary analysis revealed that 60 out of 65 seismic stations on the ice sheet obtained clear peak frequencies (f0) related to the ice sheet thickness in the H / V spectrum. Thus, assuming that the isotropic ice layer lies atop a high velocity half-space bedrock, the ice sheet thickness can be calculated by a simple approximation formula. About half of the calculated ice sheet thicknesses were consistent with the Bedmap2 ice thickness values. To further improve the reliability of ice thickness measurements, two-type models were built to fit the observed H / V spectrum through non-linear inversion. The two-type models represent the isotropic structures of single- and two-layer ice sheets, and the latter depicts the non-uniform, layered characteristics of the ice sheet widely distributed in Antarctica. The inversion results suggest that the ice thicknesses derived from the two-layer ice models were in good concurrence with the Bedmap2 ice thickness database, and that ice thickness differences between the two were within 300 m at almost all stations. Our results support previous finding that the Antarctic ice sheet is stratified. Extensive data processing indicates that the time length of seismic ambient noise records can be shortened to two hours for reliable ice sheet thickness estimation using the H / V method. This study extends the application fields of the H / V method and provides an effective and independent way to measure ice sheet thickness in Antarctica.

  17. Surface wave imaging of the weakly extended Malawi Rift from ambient-noise and teleseismic Rayleigh waves from onshore and lake-bottom seismometers

    Science.gov (United States)

    Accardo, N. J.; Gaherty, J. B.; Shillington, D. J.; Ebinger, C. J.; Nyblade, A. A.; Mbogoni, G. J.; Chindandali, P. R. N.; Ferdinand, R. W.; Mulibo, G. D.; Kamihanda, G.; Keir, D.; Scholz, C.; Selway, K.; O'Donnell, J. P.; Tepp, G.; Gallacher, R.; Mtelela, K.; Salima, J.; Mruma, A.

    2017-06-01

    Located at the southernmost sector of the Western Branch of the East African Rift System, the Malawi Rift exemplifies an active, magma-poor, weakly extended continental rift. To investigate the controls on rifting, we image crustal and uppermost mantle structure beneath the region using ambient-noise and teleseismic Rayleigh-wave phase velocities between 9 and 100 s period. Our study includes six lake-bottom seismometers located in Lake Malawi (Nyasa), the first time seismometers have been deployed in any of the African rift lakes. Noise levels in the lake are lower than that of shallow oceanic environments and allow successful application of compliance corrections and instrument orientation determination. Resulting phase-velocity maps reveal slow velocities primarily confined to Lake Malawi at short periods (T 25 s), a prominent low-velocity anomaly exists beneath the Rungwe Volcanic Province at the northern terminus of the rift basin. Estimates of phase-velocity sensitivity indicates these low velocities occur within the lithospheric mantle and potentially uppermost asthenosphere, suggesting that mantle processes may control the association of volcanic centres and the localization of magmatism. Beneath the main portion of the Malawi Rift, a modest reduction in velocity is also observed at periods sensitive to the crust and upper mantle, but these velocities are much higher than those observed beneath Rungwe.

  18. Strong tracking adaptive Kalman filters for underwater vehicle dead reckoning

    Science.gov (United States)

    Xiao, Kun; Fang, Shao-Ji; Pang, Yong-Jie

    2007-06-01

    To impove underwater vehicle dead reckoning, a developed strong tracking adaptive kalman filter is proposed. The filter is improved with an additional adaptive factor and an estimator of measurement noise covariance. Since the magnitude of fading factor is changed adaptively, the tracking ability of the filter is still enhanced in low velocity condition of underwater vehicles. The results of simulation tests prove the presented filter effective.

  19. GSpecDisp: A matlab GUI package for phase-velocity dispersion measurements from ambient-noise correlations

    Science.gov (United States)

    Sadeghisorkhani, Hamzeh; Gudmundsson, Ólafur; Tryggvason, Ari

    2018-01-01

    We present a graphical user interface (GUI) package to facilitate phase-velocity dispersion measurements of surface waves in noise-correlation traces. The package, called GSpecDisp, provides an interactive environment for the measurements and presentation of the results. The selection of a dispersion curve can be done automatically or manually within the package. The data are time-domain cross-correlations in SAC format, but GSpecDisp measures phase velocity in the spectral domain. Two types of phase-velocity dispersion measurements can be carried out with GSpecDisp; (1) average velocity of a region, and (2) single-pair phase velocity. Both measurements are done by matching the real part of the cross-correlation spectrum with the appropriate Bessel function. Advantages of these two types of measurements are that no prior knowledge about surface-wave dispersion in the region is needed, and that phase velocity can be measured up to that period for which the inter-station distance corresponds to one wavelength. GSpecDisp can measure the phase velocity of Rayleigh and Love waves from all possible components of the noise correlation tensor. First, we briefly present the theory behind the methods that are used, and then describe different modules of the package. Finally, we validate the developed algorithms by applying them to synthetic and real data, and by comparison with other methods. The source code of GSpecDisp can be downloaded from: https://github.com/Hamzeh-Sadeghi/GSpecDisp

  20. Shallow velocity structure above the Socorro Magma Body from ambient noise tomography using the large-N Sevilleta array, central Rio Grande Rift, New Mexico

    Science.gov (United States)

    Worthington, L. L.; Ranasinghe, N. R.; Schmandt, B.; Jiang, C.; Finlay, T. S.; Bilek, S. L.; Aster, R. C.

    2017-12-01

    The Socorro Magma Body (SMB) is one of the largest recognized active mid-crustal magma intrusions globally. Inflation of the SMB drives sporadically seismogenic uplift at rates of up to of few millimeters per year. We examine the upper crustal structure of the northern section of the SMB region using ambient noise seismic data collected from the Sevilleta Array and New Mexico Tech (NMT) seismic network to constrain basin structure and identify possible upper crustal heterogeneities caused by heat flow and/or fluid or magma migration to shallower depths. The Sevilleta Array comprised 801 vertical-component Nodal seismic stations with 10-Hz seismometers deployed within the Sevilleta National Wildlife Refuge in the central Rio Grande rift north of Socorro, New Mexico, for a period of 12 days during February 2015. Five short period seismic stations from the NMT network located south of the Sevilleta array are also used to improve the raypath coverage outside the Sevilleta array. Inter-station ambient noise cross-correlations were computed from all available 20-minute time windows and stacked to obtain estimates of the vertical component Green's function. Clear fundamental mode Rayleigh wave energy is observed from 3 to 6 s period. Beamforming indicates prominent noise sources from the southwest, near Baja California, and the southeast, in the Gulf of Mexico. The frequency-time analysis method was implemented to measure fundamental mode Rayleigh wave phase velocities and the resulting inter-station travel times were inverted to obtain 2-D phase velocity maps. One-dimensional sensitivity kernels indicate that the Rayleigh wave phase velocity maps are sensitive to a depth interval of 1 to 8 km, depending on wave period. The maps show (up to 40%) variations in phase velocity within the Sevilleta Array, with the largest variations found for periods of 5-6 seconds. Holocene to upper Pleistocene, alluvial sediments found in the Socorro Basin consistently show lower phase

  1. Natural and anthropogenic ocean noise recorded at long-term and temporary observatories

    Science.gov (United States)

    Grevemeyer, Ingo; Metz, Dirk; Watts, Anthony B.; Geissler, Wolfram

    2017-04-01

    Most people worldwide would assume that the oceans are silent. However, a number of natural phenomenon's like ocean waves, wind, lightening, ice noise, earthquakes, and submarine volcanic activity contributes to the ambient ocean noise. During their evolution, marine animals like fish and mammals have adopted in many ways to the acoustic properties of the sea. Yet in recent decades, anthropogenic and hence manmade ocean noise level has risen profoundly. Due to extreme reliance of fish and mammals on underwater sounds for basic life functions, including searching for food or mate and the absence of any mechanism to safeguard them against it, underwater noise pollution may disrupt marine life. The primary sources of low-frequency anthropogenic noise include sounds associated with shipping, military operations, oil and gas exploration and production, and even research activities. Some scientists suggest that today virtually no marine environment is without any noise pollution. Thus, all marine life forms that rely heavily on the integrity of their acoustic habitat may have to adapt to new conditions. Of greatest concern for whales are low-frequency sounds that travel long distances in the ocean. Ship propellers and motors, for instance, produce sound at low frequencies, as do natural and manmade seismic activity. These profound, loud noises reverberate in the deep ocean and can effectively mask or block vital whale communication. However, in general very little is known about the world-wide distribution of ambient ocean noise. Thus, on a global scale and considering the vast areas of the world's oceans, we know virtually nothing about noise levels in different parts of the oceans and how anthropogenic noise contributes to ambient noise. Here, we use hydrophone recordings from the UN's Comprehensive Nuclear-Test-Ban Treaty organization (CTBTO) and ocean-bottom seismometers to provide an assessment of noise in all major basins, including the Pacific, Atlantic and Indian

  2. Underwater Scene Composition

    Science.gov (United States)

    Kim, Nanyoung

    2009-01-01

    In this article, the author describes an underwater scene composition for elementary-education majors. This project deals with watercolor with crayon or oil-pastel resist (medium); the beauty of nature represented by fish in the underwater scene (theme); texture and pattern (design elements); drawing simple forms (drawing skill); and composition…

  3. Ambiente urbano e percepção da poluição sonora Urban environment and perception to noise pollution

    Directory of Open Access Journals (Sweden)

    Adriana Bender Moreira de Lacerda

    2005-12-01

    Full Text Available A presente pesquisa avaliou a percepção da população de uma grande cidade em relação à poluição sonora (ruído urbano. Buscou-se identificar quais fontes sonoras são percebidas com maior freqüência pela população e quais reações psico-sociais relacionadas ao ruído urbano são identificados por ela. Foi utilizado um questionário composto de questões fechadas, abrangendo aspectos demográficos e aspectos psico-sociais referentes ao ruído ambiental. Oitocentos e noventa e dois (892 indivíduos participaram da pesquisa. As principais fontes de ruído citadas pelos moradores como causadoras de incômodo foram: 1 o tráfego de veículos (67 %, 2 os vizinhos (33%, 3 o barulho de sirenes (23%, 4 o barulho de animais (21% e 5 o barulho gerado pela construção civil (21 %. As principais reações psico-sociais foram: 1 irritabilidade (55%, 2 baixa concentração (28%, 3 insônia (20% e 4 dor de cabeça (19%. Os resultados obtidos coincidem com dados obtidos em pesquisas desenvolvidas na Europa, EUA e no Brasil, de que a poluição sonora ambiental influencia a qualidade de vida da população, gerando reações psico-sociais importantes, como: 1 irritabilidade e 2 insônia. Estes podem estar na base de outras doenças (disfunções cardiovasculares, podendo interferir na saúde e no bem estar dos indivíduos em particular e de uma população urbana como um todo, gerando um problema de saúde pública.The present study investigated the psychosocial complaints related to urban noise among the population of Curitiba. We used a questionnaire of closed-set questions to collect data on demographics and psychosocial reactions to environmental noise when subjects are at home. Eight hundred and ninety-two individuals (892 participated of the study. The main noise sources associated with discomfort or annoyance were traffic noise (67%, neighbors (33%, sirens (23%, animals (21%, and construction (21%. The main psychosocial complaints were

  4. A Trial for Detecting the Temporal Variation in Seismic Velocity Accompanied by a Slow Slip Event using Seismic Interferometry of Ambient Noise

    Science.gov (United States)

    Uemura, Miyuu; Ito, Yoshihiro; Ohta, Kazuaki; Hino, Ryota; Shinohara, Masanao

    2017-04-01

    Seismic interferometry is one of the most effective techniques to detect temporal variations in seismic velocity before or after a large earthquake. Some previous studies have been reported on seismic velocity reduction due to the occurrence of large earthquakes (e.g., Wegler et al., 2009; Yamada et al., 2010) as well as preceding them (e.g., Lockner et al., 1977; Yoshimitsu et al., 2009). However, there have only been a few studies thus far which attempt to detect seismic velocity changes associated with slow slip events (SSEs). In this study, we focus on applying seismic interferometry to ambient noise data from ocean bottom seismometers (OBSs) deployed near a subduction zone. Between the end of January 2011 and the largest foreshock occurring on March 9th that precedes the March 11, 2011 Tohoku-Oki earthquake, SSEs and low-frequency tremors were detected offshore Miyagi Prefecture (Ito et al., 2013, 2015; Katakami et al., 2016). We applied our seismic interferometry analysis using ambient noise to recordings from 17 OBS stations that were installed in the vicinity of the 2011 Tohoku-Oki earthquake source region, and only considered the recordings from before that major earthquake. All the OBSs are short-period seismometers with three components which have an eigenfrequency of 4.5 Hz. These OBSs were deployed offshore Miyagi Prefecture between November 2010 and April 2011. Before proceeding with the seismic interferometry analysis, we needed to estimate the two horizontal components of the original deployment orientation for 13 OBSs in (we could not estimate them for 4 OBSs). To obtain the OBS orientation, we used particle orbits of some direct P waves from selected tectonic earthquakes, in order to extract one vertical and two horizontal components. Then, the seismic interferometry analysis consisted of the following steps. First, we applied a band-pass filter of 0.25-2.0 Hz and one-bit technique to the ambient noise signal. Second, we calculated auto

  5. Crustal and upper mantle shear velocities of Iberia, the Alboran Sea, and North Africa from ambient noise and ballistic finite-frequency Rayleigh wave tomography

    Science.gov (United States)

    Palomeras, I.; Villasenor, A.; Thurner, S.; Levander, A.; Gallart, J.; mimoun, H.

    2013-12-01

    The complex Mesozoic-Cenozoic Alpine deformation in the western Mediterranean extends from the Pyrenees in northern Spain to the Atlas Mountains in southern Morocco. The Iberian plate was accreted to the European plate in late Cretaceous, resulting in the formation of the Pyrenees. Cenozoic African-European convergence resulted in subduction of the Tethys oceanic plate beneath Europe. Rapid Oligocene slab rollback from eastern Iberia spread eastward and southward, with the trench breaking into three segments by the time it reached the African coast. One trench segment moved southwestward and westward creating the Alboran Sea, floored by highly extended continental crust, and building the encircling Betics Rif mountains comprising the Gibraltar arc, and the Atlas mountains, which formed as the inversion of a Jurassic rift. A number of recent experiments have instrumented this region with broad-band arrays (the US PICASSO array, Spanish IberArray and Siberia arrays, the University of Munster array), which, including the Spanish, Portuguese, and Moroccan permanent networks, provide a combined array of 350 stations having an average interstation spacing of ~60 km. Taking advantage of this dense deployment, we have calculated the Rayleigh waves phase velocities from ambient noise for short periods (4 s to 40 s) and teleseismic events for longer periods (20 s to 167 s). Approximately 50,000 stations pairs were used to measure the phase velocity from ambient noise and more than 160 teleseismic events to measure phase velocity for longer periods. The inversion of the phase velocity dispersion curves provides a 3D shear velocity for the crust and uppermost mantle. Our results show differences between the various tectonic regions that extend to upper mantle depths (~200 km). In Iberia we obtain, on average, higher upper mantle shear velocities in the western Variscan region than in the younger eastern part. We map high upper mantle velocities (>4.6 km/s) beneath the

  6. Integrating ambient noise with GIS for a new perspective on volcano imaging and monitoring: The case study of Mt. Etna

    Science.gov (United States)

    Guardo, R.; De Siena, L.

    2017-11-01

    The timely estimation of short- and long-term volcanic hazard relies on the availability of detailed 3D geophysical images of volcanic structures. High-resolution seismic models of the absorbing uppermost conduit systems and highly-heterogeneous shallowest volcanic layers, while particularly challenging to obtain, provide important data to locate feasible eruptive centres and forecast flank collapses and lava ascending paths. Here, we model the volcanic structures of Mt. Etna (Sicily, Italy) and its outskirts using the Horizontal to Vertical Spectral Ratio method, generally applied to industrial and engineering settings. The integration of this technique with Web-based Geographic Information System improves precision during the acquisition phase. It also integrates geological and geophysical visualization of 3D surface and subsurface structures in a queryable environment representing their exact three-dimensional geographic position, enhancing interpretation. The results show high-resolution 3D images of the shallowest volcanic and feeding systems, which complement (1) deeper seismic tomography imaging and (2) the results of recent remote sensing imaging. The study recovers a vertical structure that divides the pre-existing volcanic complexes of Ellittico and Cuvigghiuni. This could be interpreted as a transitional phase between the two systems. A comparison with recent remote sensing and geological results, however, shows that anomalies are generally related to volcano-tectonic structures active during the last 17 years. We infer that seismic noise measurements from miniaturized instruments, when combined with remote sensing techniques, represent an important resource to monitor volcanoes in unrest, reducing the risk of loss of human lives and instrumentation.

  7. Engineering geological zonation of a complex landslide system through seismic ambient noise measurements at the Selmun Promontory (Malta)

    Science.gov (United States)

    Iannucci, Roberto; Martino, Salvatore; Paciello, Antonella; D'Amico, Sebastiano; Galea, Pauline

    2018-01-01

    The cliff slope of the Selmun Promontory, located in the Northern part of the island of Malta (Central Mediterranean Sea) close to the coastline, is involved in a landslide process as exhibited by the large block-size talus at its bottom. The landslide process is related to the geological succession outcropping in the Selmun area, characterised by the over-position of a grained limestone on a plastic clay, that induces a lateral spreading phenomenon associated with detachment and collapse of different-size rock blocks. The landslide process shapes a typical landscape with a stable plateau of stiff limestone bordered by an unstable cliff slope. The ruins of Għajn Ħadid Tower, the first of the thirteen watchtowers built in 1658 by the Grand Master Martin de Redin, stand out on the Selmun Promontory. The conservation of this important heritage site, already damaged by an earthquake which struck the Maltese Archipelago on October 12th 1856, is currently threatened by a progressive retreat of the landslide process towards the inland plateau area. During 2015 and 2016, field surveys were carried out to derive an engineering geological model of the Selmun Promontory. After a high-resolution geomechanical survey, the spatial distribution of the joints affecting the limestone was obtained. At the same time, 116 single-station noise measurements were carried out to cover the inland and edge plateau zones as well as the clayey slope area. The obtained 1-hour time histories were analysed through the horizontal to vertical spectral ratio (HVSR) technique, as well as polarity and ellipticity analysis of particle motion to define the local seismic response in zones having different stability conditions, i.e. related to the presence of unstable rock blocks characterised by different vibrational modes. The results obtained confirm the suitability of passive seismic geophysical techniques for zoning landslide hazard in case of rock slopes and demonstrate the relevance of

  8. Crustal and upper mantle S-wave velocity structures across the Taiwan Strait from ambient seismic noise and teleseismic Rayleigh wave analyses

    Science.gov (United States)

    Huang, Y.; Yao, H.; Wu, F. T.; Liang, W.; Huang, B.; Lin, C.; Wen, K.

    2013-12-01

    Although orogeny seems to have stopped in western Taiwan large and small earthquakes do occur in the Taiwan Strait. Limited studies have focused on this region before and were barely within reach for comprehensive projects like TAICRUST and TAIGER for logistical reasons; thus, the overall crustal structures of the Taiwan Strait remain unknown. Time domain empirical Green's function (TDEGF) from ambient seismic noise to determine crustal velocity structure allows us to study an area using station pairs on its periphery. This research aims to resolve 1-D average crustal and upper mantle S-wave velocity (Vs) structures alone paths of several broadband station-pairs across the Taiwan Strait; 5-120 s Rayleigh wave phase velocity dispersion data derived by combining TDEGF and traditional surface wave two-station method (TS). The average Vs structures show significant differences in the upper 15 km as expected. In general, the highest Vs are observed in the coastal area of Mainland China and the lowest Vs appear along the southwest offshore of the Taiwan Island; they differ by about 0.6-1.1 km/s. For different parts of the Strait, the Vs are lower in the middle by about 0.1-0.2 km/s relative to those in the northern and southern parts. The overall crustal thickness is approximately 30 km, much thinner and less variable than under the Taiwan Island.

  9. Underwater 3D filming

    Directory of Open Access Journals (Sweden)

    Roberto Rinaldi

    2014-12-01

    Full Text Available After an experimental phase of many years, 3D filming is now effective and successful. Improvements are still possible, but the film industry achieved memorable success on 3D movie’s box offices due to the overall quality of its products. Special environments such as space (“Gravity” and the underwater realm look perfect to be reproduced in 3D. “Filming in space” was possible in “Gravity” using special effects and computer graphic. The underwater realm is still difficult to be handled. Underwater filming in 3D was not that easy and effective as filming in 2D, since not long ago. After almost 3 years of research, a French, Austrian and Italian team realized a perfect tool to film underwater, in 3D, without any constrains. This allows filmmakers to bring the audience deep inside an environment where they most probably will never have the chance to be.

  10. Underwater Glider System Study

    OpenAIRE

    Jenkins, Scott A; Humphreys, Douglas E; Sherman, Jeff; Osse, Jim; Jones, Clayton; Leonard, Naomi; Graver, Joshua; Bachmayer, Ralf; Clem, Ted; Carroll, Paul; Davis, Philip; Berry, Jon; Worley, Paul; Wasyl, Joseph

    2003-01-01

    The goals of this study are to determine how to advance from present capabilities of underwater glider (and hybrid motorglider) technology to what could be possible within the next few years; and to identify critical research issues that must be resolved to make such advancements possible. These goals were pursued by merging archival flight data with numerical model results and system spreadsheet analysis to extrapolate from the present state-of-the–art in underwater (UW) gliders to potential...

  11. Hovercraft Underwater Noise Measurements in Alaska.

    Science.gov (United States)

    2001-04-02

    The United States Postal Service (USPS) is finishing a two-year demonstration project : examining the feasibility of mail delivery via hovercraft to remote Alaskan villages. Prior to this : demonstration project, and in support of the Environmental A...

  12. Polarization Calculation and Underwater Target Detection Inspired by Biological Visual Imaging

    Directory of Open Access Journals (Sweden)

    Jie Shen

    2014-04-01

    Full Text Available In challenging underwater environments, the polarization parameter maps calculated by the Stokes model are characterized by the high noise and error, harassing the underwater target detection tasks. In order to solve this problem, this paper proposes a novel bionic polarization calculation and underwater target detection method by modeling the visual system of mantis shrimps. This system includes many operators including a polarization-opposition calculation, a factor optimization and a visual neural network model. A calibration learning method is proposed to search the optimal value of the factors in the linear subtraction model. Finally, a six-channel visual neural network model is proposed to detect the underwater targets. Experimental results proved that the maps produced by the polarization-opposition parameter is more accurate and have lower noise than that produced by the Stokes parameter, achieving better performance in underwater target detection tasks.

  13. Crustal and uppermost mantle S-wave velocity below the East European Craton in northern Poland from the inversion of ambient-noise records

    Science.gov (United States)

    Lepore, Simone; Polkowski, Marcin; Grad, Marek

    2018-02-01

    The P-wave velocities (V p) within the East European Craton in Poland are well known through several seismic experiments which permitted to build a high-resolution 3D model down to 60 km depth. However, these seismic data do not provide sufficient information about the S-wave velocities (V s). For this reason, this paper presents the values of lithospheric V s and P-wave-to-S-wave velocity ratios (V p/V s) calculated from the ambient noise recorded during 2014 at "13 BB star" seismic array (13 stations, 78 midpoints) located in northern Poland. The 3D V p model in the area of the array consists of six sedimentary layers having total thickness within 3-7 km and V p in the range 1.85.3 km/s, a three-layer crystalline crust of total thickness 40 km and V p within 6.15-7.15 km/s, and the uppermost mantle, where V p is about 8.25 km/s. The V s and V p/V s values are calculated by the inversion of the surface-wave dispersion curves extracted from the noise cross correlation between all the station pairs. Due to the strong velocity differences among the layers, several modes are recognized in the 0.021 Hz frequency band: therefore, multimodal Monte Carlo inversions are applied. The calculated V s and V p/V s values in the sedimentary cover range within 0.992.66 km/s and 1.751.97 as expected. In the upper crust, the V s value (3.48 ± 0.10 km/s) is very low compared to the starting value of 3.75 ± 0.10 km/s. Consequently, the V p/V s value is very large (1.81 ± 0.03). To explain that the calculated values are compared with the ones for other old cratonic areas.

  14. Cymbal and BB underwater transducers and arrays

    Energy Technology Data Exchange (ETDEWEB)

    Newnham, R.E.; Zhang, J.; Alkoy, S.; Meyer, R.; Hughes, W.J.; Hladky-Hennion, A.C.; Cochran, J.; Markley, D. [Materials Research Laboratory, Penn State University, University Park, PA 16802 (United States)

    2002-09-01

    The cymbal is a miniaturized class V flextensional transducer that was developed for use as a shallow water sound projector and receiver. Single elements are characterized by high Q, low efficiency, and medium power output capability. Its low cost and thin profile allow the transducer to be assembled into large flexible arrays. Efforts were made to model both single elements and arrays using the ATILA code and the integral equation formulation (EQI).Millimeter size microprobe hydrophones (BBs) have been designed and fabricated from miniature piezoelectric hollow ceramic spheres for underwater applications such as mapping acoustic fields of projectors, and flow noise sensors for complex underwater structures. Green spheres are prepared from soft lead zirconate titanate powders using a coaxial nozzle slurry process. A compact hydrophone with a radially-poled sphere is investigated using inside and outside electrodes. Characterization of these hydrophones is done through measurement of hydrostatic piezoelectric charge coefficients, free field voltage sensitivities and directivity beam patterns. (orig.)

  15. San Andreas Fault dip, Peninsular Ranges mafic lower crust and partial melt in the Salton Trough, Southern California, from ambient-noise tomography

    Science.gov (United States)

    Barak, Shahar; Klemperer, Simon L.; Lawrence, Jesse F.

    2015-11-01

    We use ambient-noise tomography to improve CVM-H11.9, a community velocity model of southern California. Our new 3-D shear-velocity model with 0.05° x 0.05° lateral and 1 km vertical blocks reveals new structure beneath the San Andreas Fault (SAF), Peninsular Ranges batholith (PRB), southern Sierra Nevada batholith (SNB), and the Salton Trough (ST). We use 4 years of data recorded on 849 broadband stations, vastly more than previous studies and including our own broadband Salton Seismic Imaging Project, a 40 station transect across the ST, as well as other campaign stations in both Mexico and the United States. Mean lower crust and upper mantle wave speeds (3.6 km/s at 20 km, 4.2 km/s at 40 km) are low by global standards. Across the SAF, southeast of San Gorgonio Pass, we observe vertical to steeply dipping lateral velocity contrasts that extend beneath the Moho. Beneath the western PRB and westernmost southern SNB, we observe relatively high shear velocities (≥3.8 km/s) in the lower crust that we interpret as the mafic roots of the overlying arc. Relatively high-velocity upper mantle (up to ˜4.5 km/s) may be part of the intact arc, or possibly a remnant of the Farallon plate. Beneath the ST, we observe zones of low shear-velocity in the lower crust and upper mantle which permit up to ˜4.5% melt in the lower crust and up to ˜6% melt in the upper mantle, depending on the assumed composition and pore geometry. Our results preclude the existence of older continental crust beneath the ST and support the creation of new crust beneath the ST.

  16. "Boxnep" advanced modular underwater robot

    OpenAIRE

    Buluev, Ilia

    2016-01-01

    The article discusses the relevance of the underwater vehicles' ability to solve a wide range of problems. The idea put in the basis of this research is designing a modular underwater robot. It allows to mount various equipment and test it in underwater environment. The paper deals with the concept of the robot and its characteristics.

  17. Resources for Underwater Robotics Education

    Science.gov (United States)

    Wallace, Michael L.; Freitas, William M.

    2016-01-01

    4-H clubs can build and program underwater robots from raw materials. An annotated resource list for engaging youth in building underwater remotely operated vehicles (ROVs) is provided. This article is a companion piece to the Research in Brief article "Building Teen Futures with Underwater Robotics" in this issue of the "Journal of…

  18. Deep Learning Methods for Underwater Target Feature Extraction and Recognition

    Directory of Open Access Journals (Sweden)

    Gang Hu

    2018-01-01

    Full Text Available The classification and recognition technology of underwater acoustic signal were always an important research content in the field of underwater acoustic signal processing. Currently, wavelet transform, Hilbert-Huang transform, and Mel frequency cepstral coefficients are used as a method of underwater acoustic signal feature extraction. In this paper, a method for feature extraction and identification of underwater noise data based on CNN and ELM is proposed. An automatic feature extraction method of underwater acoustic signals is proposed using depth convolution network. An underwater target recognition classifier is based on extreme learning machine. Although convolution neural networks can execute both feature extraction and classification, their function mainly relies on a full connection layer, which is trained by gradient descent-based; the generalization ability is limited and suboptimal, so an extreme learning machine (ELM was used in classification stage. Firstly, CNN learns deep and robust features, followed by the removing of the fully connected layers. Then ELM fed with the CNN features is used as the classifier to conduct an excellent classification. Experiments on the actual data set of civil ships obtained 93.04% recognition rate; compared to the traditional Mel frequency cepstral coefficients and Hilbert-Huang feature, recognition rate greatly improved.

  19. The seismic ambient noise spectral ratio H/V under de diffuse field approach for simple layered models: Asymptotic behavior for low and high frequencies

    Science.gov (United States)

    Luzón, F.; García-Jerez, A.; Sanchez-Sesma, F. J.; Lunedei, E.; Albarello, D.; Santoyo, M. A.; Almendros, J.

    2013-05-01

    The possibility of retrieving the elastodynamic Green's tensor between two points within an elastic medium from time-domain correlation of ambient noise recorded at such sites was duly confirmed in the pioneering seismic experiments by Campillo and Paul (2003) and Shapiro and Campillo (2004). Afterwards, several theoretical works on this subject have been conducted for simple models showing that such a possibility implies the condition of diffuse wavefield which requires isotropy of the illumination or the fulfillment of certain relationships between the energies of different types of waves (derived from the energy equipartition principle). In this work we examine the reliability of the usual assumptions that emerge from the Diffuse Field Approach (DFA). In particular we deal with the wavefield composition in applications regarding the passive seismic prospecting. We revise briefly the more general formulation of the DFA for full wavefield (FW). In this case the contribution of each wave to the horizontal-and vertical power spectra at surface are analyzed for a simple elastic waveguide (for instance the continental crust-upper mantle interface). Special attention is paid to their compositions at low-and high-frequencies, obtaining the relative powers of each surface wave (SW) type by means of a semi-analytical analysis. We found for some simple models that if body waves are removed from the analysis, the high-frequency horizontal asymptote of the H/V spectral ratio decreases slightly (from 1.33 for FW to around 1.14 for SW) and shows dependence on both the Poisson's ratio of the crust and the S-wave velocity contrast (while FW-H/V asymptote depends on the former only). Experimental tests for a broad band network deployed at SW Pyrenees edge provide H/V curves compatible with any of these values in the band 0.2-1Hz, approximately, supporting the applicability of the DFA approximation. Coexistence of multiple SW-modes produces distortion in the amplitude of both

  20. Spatio-temporal changes in seismic velocity associated with the 2000 activity of Miyakejima volcano as inferred from cross-correlation analyses of ambient noise

    Science.gov (United States)

    Anggono, Titi; Nishimura, Takeshi; Sato, Haruo; Ueda, Hideki; Ukawa, Motoo

    2012-12-01

    Miyakejima volcano, Japan, showed strong and interesting volcanic activities in 2000 with the occurrence of dike intrusions, caldera formation and a large amount of gas emission. To understand temporal changes of the volcanic structure associated with this activity, we apply ambient noise correlation analyses to the seismic records of five seismic stations at Miyakejima volcano from July 1999 to December 2002. We calculate cross-correlation functions (CCFs) for eight available station pairs at frequency bands of 0.4-0.8 Hz and 0.8-1.6 Hz, and retrieve the Rayleigh waves propagating with a group velocity of about 1.0 km/s. Comparing CCFs obtained for each day with the reference CCFs that are calculated from a few months of data, we estimate seismic velocity changes before and after the 2000 activity. Results at the two frequency bands show seismic velocity increase and decrease. Shallow structure at the volcanic edifice on the flanks experienced a seismic velocity increase up to 3.3%. On the other hand, the regions located close to the collapsed caldera show a seismic velocity decrease down to 2.3%. To understand the mechanisms that may introduce these seismic velocity increase and decrease, we examine several possible mechanisms of the velocity changes: stress changes due to volcanic pressure sources and caldera formation, and topographic changes. By using the deflation sources previously determined from GPS data, we calculate the stresses at depths of 0 km and 1 km at the volcano. The results suggest that the seismic velocity increases observed at seismic paths on the volcanic flank are explained by the compression caused by the deflation sources associated with magma activity in 2000. Stress sensitivities of the seismic velocity changes are estimated to be 1.5 × 10- 2 to 2.2 × 10- 2 MPa- 1 and 4.6 × 10- 3 to 2.4 × 10- 2 MPa- 1 at frequency bands of 0.4-0.8 Hz and 0.8-1.6 Hz, respectively, which are in the range of the previously reported results. Our three

  1. 3-D structure of the crust and uppermost mantle at the junction between the Southeastern Alps and External Dinarides from ambient noise tomography

    Science.gov (United States)

    Guidarelli, Mariangela; Aoudia, Abdelkrim; Costa, Giovanni

    2017-12-01

    We use ambient noise tomography to investigate the crust and the uppermost mantle structure beneath the junction between the Southern Alps, the Dinarides and the Po Plain. We obtained Rayleigh wave empirical Green's functions from cross-correlation of vertical component seismic recordings for three years (2010-2012) using stations from networks in Italy, Slovenia, Austria, Croatia, Serbia and Switzerland. We measure group and phase velocity dispersion curves from the reconstructed Rayleigh waves in the period range 5-30 and 8-37 s, respectively, and we invert the surface wave velocities for tomographic images on a grid of 0.1° × 0.1°. After the tomography, the group velocities are then inverted to compute the 3-D shear wave velocity model of the crust and the upper mantle beneath the region. Our shear wave velocity model provides the 3-D image of the structure in the region between Northeastern Italy, Slovenia and Austria. The velocity variations at shallow depths correlate with known geological and tectonic domains. We find low velocities below the Po Plain, the northern tip of the Adriatic and the Pannonian Basin, whereas higher velocities characterize the Alpine chain. The vertical cross-sections reveal a clear northward increase of the crustal thickness with a sharp northward dipping of the Moho that coincides at the surface with the leading edge of the Alpine thrust front adjacent to the Friuli Plain in Northeastern Italy. This geometry of the Moho mimics fairly well the shallow north dipping geometry of the decollement inferred from permanent GPS velocity field where high interseismic coupling is reported. From the northern Adriatic domain up to the Idrija right lateral strike-slip fault system beneath Western Slovenia, the crustal thickness is more uniform. Right across Idrija fault, to the northeast, and along its strike, we report a clear change of the physical properties of the crust up to the uppermost mantle as reflected by the lateral distribution

  2. Spatio-temporal changes of seismic velocity at Miyakejima volcano associated with the 2000 eruption based on the cross-correlation analyses of ambient seismic noise records

    Science.gov (United States)

    Anggono, T.; Nishimura, T.; Sato, H.; Ueda, H.; Ukawa, M.

    2009-12-01

    Miyakejima Island is located about 170 km to the south of Tokyo, Japan. The 2000 activity started with a small submarine eruption in late June 2000, which accompanied earthquake swarms. A caldera was formed from July to August and had a diameter of about 1.6 km. Since then the volcanic gas was effused and the activity continued for more than four years. We analyze the ambient seismic noise recorded from July 1999 to December 2002 at four NIED seismic stations to study the volcano structure behavior associated with this volcanic activity. The continuous records are sampled at frequency of 100 Hz with an A/D resolution of 16-bit. We apply cross-correlation analyses to the continuous records of vertical component of short period seismometers (1 s) for every possible pair of stations. Before calculating the cross-correlation function (CCF), we bandpass filter the data using three-order Butterworth filter with frequency bands 0.4 - 0.8 Hz and 0.8 - 1.6 Hz. We calculate the CCFs with 60 s window length, and then stack for one day data. The observed CCFs are symmetric at both negative and positive lag times; this means that the distribution of noise sources is quite homogeneous surrounding the Miyakejima Island. We define a reference Green’s function (RGF) for every station pair by stacking the CCFs for about 10 months in 2002 during which no major instrumental errors were found. Once RGF is defined for each station pair, we calculate the cross-correlation coefficient between the RGF and the CCFs of each day, and select “good” CCFs that have cross-correlation coefficient larger than 0.7 and lag time smaller than +/- 0.5 s. We pick travel times of the maximum amplitude of the wave packets at positive and negative lag times, which correspond to the travel time of Rayleigh waves between two stations, from the RGF and the “good” CCFs of each day. To estimate the changes in the medium, we calculate the average travel time difference for periods July 1999 - May 2000

  3. Can we trace the eastern Gondwanan margin in Australia? New perspectives from transdimensional inversion of ambient noise for 3D shear velocity structure

    Science.gov (United States)

    Pilia, S.; Rawlinson, N.; Direen, N. G.

    2013-12-01

    Although the notion of Rodinia is quite well accepted in the geoscience community, the location and nature of the eastern continental margin of the Gondwana fragment in Australia is still vague and remains one of the most hotly debated topics in Australian geology. Moreover, most post-Rodinian reconstructions models choose not to tackle the ';Tasmanian challenge', and focus only on the tectonic evolution of mainland southeast Australia, thereby conveniently ignoring the wider tectonic implications of Tasmania's complex geological history. One of the chief limitations of the tectonic reconstructions in this region is a lack of information on Paleozoic (possibly Proterozoic) basement structures. Vast Mesozoic-Cainozoic sedimentary and volcanic cover sequences obscure older outcrops and limit the power of direct observational techniques. In response to these challenges, our effort is focused on ambient seismic noise for imaging 3D crustal shear velocity structure using surface waves, which is capable of illuminating basement structure beneath younger cover. The data used in this study is sourced from the WOMBAT transportable seismic array, which is compounded by around 650 stations spanning the majority of southeastern Australia, including Tasmania and several islands in Bass Strait. To produce the highest quality Green's functions, careful processing of the data has been performed, after which group velocity dispersion measurements have been carried out using a frequency-time analysis method on the symmetric component of the empirical Green's functions (EGFs). Group dispersion measurements from the EGFs have been inverted using a novel hierarchical, transdimensional, Bayesian algorithm to obtain Rayleigh-wave group velocity maps at different periods from 2 to 30 s. The new approach has several advantages in that the number and distribution of model parameters are implicitly controlled by the data, in which the noise is treated as unknown in the inversion. This

  4. Chaos-Based Underwater Communication With Arbitrary Transducers and Bandwidth

    Directory of Open Access Journals (Sweden)

    Chao Bai

    2018-01-01

    Full Text Available In this work, an enhanced differential chaos shift keying (DCSK, based on a first order hybrid chaotic system, is being proposed for a high reliability underwater acoustic communication system. It can be integrated into systems that use standard existing transducers. We show that a coherent operation between the received signal and the time reversal of the basis function in a first order hybrid chaotic system maximizes the signal to noise ratio at the receiver. Concurrently, DCSK configuration is used to resist the distortion caused by the complex underwater acoustic channel. Our simulation results show that the proposed method has lower bit error rate (BER. In addition, it shows higher communication reliability over underwater acoustic channel as compared to the conventional DCSK using logistic map and its variant forms such as Correlation Delay Shift Keying (CDSK, Phase-Separate DCSK (PS-DCSK, High Efficiency DCSK (HE-DCSK, and Reference Modulated DCSK (RM-DCSK.

  5. Underwater video enhancement using multi-camera super-resolution

    Science.gov (United States)

    Quevedo, E.; Delory, E.; Callicó, G. M.; Tobajas, F.; Sarmiento, R.

    2017-12-01

    Image spatial resolution is critical in several fields such as medicine, communications or satellite, and underwater applications. While a large variety of techniques for image restoration and enhancement has been proposed in the literature, this paper focuses on a novel Super-Resolution fusion algorithm based on a Multi-Camera environment that permits to enhance the quality of underwater video sequences without significantly increasing computation. In order to compare the quality enhancement, two objective quality metrics have been used: PSNR (Peak Signal-to-Noise Ratio) and the SSIM (Structural SIMilarity) index. Results have shown that the proposed method enhances the objective quality of several underwater sequences, avoiding the appearance of undesirable artifacts, with respect to basic fusion Super-Resolution algorithms.

  6. The Research of Optical Turbulence Model in Underwater Imaging System

    Directory of Open Access Journals (Sweden)

    Liying Sun

    2014-01-01

    Full Text Available In order to research the effect of turbulence on underwater imaging system and image restoration, the underwater turbulence model is simulated by computer fluid dynamics. This model is obtained in different underwater turbulence intensity, which contains the pressure data that influences refractive index distribution. When the pressure value is conversed to refractive index, the refractive index distribution can be received with the refraction formula. In the condition of same turbulent intensity, the distribution of refractive index presents gradient in the whole region, with disorder and mutations in the local region. With the turbulence intensity increase, the holistic variation of the refractive index in the image is larger, and the refractive index change more tempestuously in the local region. All the above are illustrated by the simulation results with he ray tracing method and turbulent refractive index model. According to different turbulence intensity analysis, it is proved that turbulence causes image distortion and increases noise.

  7. Underwater Gliders: A Review

    Directory of Open Access Journals (Sweden)

    Javaid Muhammad Yasar

    2014-07-01

    Full Text Available Underwater gliders are a type of underwater vehicle that transverse the oceans by shifting its buoyancy, during which its wings develop a component of the downward motion in the horizontal plane, thus producing a forward force. They are primarily used in oceanography sensing and data collection and play an important role in ocean research and development. Although there have been considerable developments in these gliders since the development of the first glider concept in 1989, to date, no review of these gliders have been done. This paper reviews existing underwater gliders, with emphasis on their respective working principles, range and payload capacity. All information on gliders available in the public domain or published in literature from the year 2000-2013 was reviewed. The majority of these gliders have an operational depth of 1000 m and a payload of less than 25 kg. The exception is a blend-body shape glider, which has a payload of approximately 800 kg and an operational depth around about 300 m. However, the commercialization of these gliders has been limited with only three know examples that have been successfully commercialized.

  8. Characterizing large river sounds: Providing context for understanding the environmental effects of noise produced by hydrokinetic turbines.

    Science.gov (United States)

    Bevelhimer, Mark S; Deng, Z Daniel; Scherelis, Constantin

    2016-01-01

    Underwater noise associated with the installation and operation of hydrokinetic turbines in rivers and tidal zones presents a potential environmental concern for fish and marine mammals. Comparing the spectral quality of sounds emitted by hydrokinetic turbines to natural and other anthropogenic sound sources is an initial step at understanding potential environmental impacts. Underwater recordings were obtained from passing vessels and natural underwater sound sources in static and flowing waters. Static water measurements were taken in a lake with minimal background noise. Flowing water measurements were taken at a previously proposed deployment site for hydrokinetic turbines on the Mississippi River, where sounds created by flowing water are part of all measurements, both natural ambient and anthropogenic sources. Vessel sizes ranged from a small fishing boat with 60 hp outboard motor to an 18-unit barge train being pushed upstream by tugboat. As expected, large vessels with large engines created the highest sound levels, which were, on average, 40 dB greater than the sound created by an operating hydrokinetic turbine. A comparison of sound levels from the same sources at different distances using both spherical and cylindrical sound attenuation functions suggests that spherical model results more closely approximate observed sound attenuation.

  9. Ambient diagnostics

    CERN Document Server

    Cai, Yang

    2014-01-01

    Part I. FundamentalsIntroductionWhat is Ambient Diagnostics?Diagnostic ModelsMultimedia IntelligenceCrowd SourcingSoft SensorsScience of SimplicityPersonal DiagnosesBasic AlgorithmsBasic ToolsSummaryProblemsTransformationEarly Discoveries of Heartbeat PatternsTransforms, Features, and AttributesSequential FeaturesSpatiotemporal FeaturesShape FeaturesImagery FeaturesFrequency Domain FeaturesMulti-Resolution FeaturesSummaryProblemsPattern RecognitionSimilarities and DistancesClustering MethodsClassification MethodsClassifier Accuracy MeasuresSummaryProblemsPart II. Multimedia IntelligenceSound RecognitionMicrophone AppsModern Acoustic Transducers (Microphones)Frequency Response CharacteristicsDigital Audio File FormatsHeart Sound SensingLung Sound SensingSnore MeterSpectrogram (STFT)Ambient Sound AnalysisSound RecognitionRecognizing Asthma SoundPeak ShiftFeature CompressionRegroupingNoise IssuesFuture ApplicationsSummaryProblemsColor SensorsColor SensingHuman Color VisionColor SensorsColor Matching ExperimentsC...

  10. Design and implementation of an underwater sound recording device.

    Science.gov (United States)

    Martinez, Jayson J; Myers, Josh R; Carlson, Thomas J; Deng, Z Daniel; Rohrer, John S; Caviggia, Kurt A; Woodley, Christa M; Weiland, Mark A

    2011-01-01

    To monitor the underwater sound and pressure waves generated by anthropogenic activities such as underwater blasting and pile driving, an autonomous system was designed to record underwater acoustic signals. The underwater sound recording device (USR) allows for connections of two hydrophones or other dynamic pressure sensors, filters high frequency noise out of the collected signals, has a gain that can be independently set for each sensor, and allows for 2 h of data collection. Two versions of the USR were created: a submersible model deployable to a maximum depth of 300 m, and a watertight but not fully submersible model. Tests were performed on the USR in the laboratory using a data acquisition system to send single-frequency sinusoidal voltages directly to each component. These tests verified that the device operates as designed and performs as well as larger commercially available data acquisition systems, which are not suited for field use. On average, the designed gain values differed from the actual measured gain values by about 0.35 dB. A prototype of the device was used in a case study to measure blast pressures while investigating the effect of underwater rock blasting on juvenile Chinook salmon and rainbow trout. In the case study, maximum positive pressure from the blast was found to be significantly correlated with frequency of injury for individual fish. The case study also demonstrated that the device withstood operation in harsh environments, making it a valuable tool for collecting field measurements.

  11. Design and Implementation of an Underwater Sound Recording Device

    Directory of Open Access Journals (Sweden)

    Christa M. Woodley

    2011-09-01

    Full Text Available To monitor the underwater sound and pressure waves generated by anthropogenic activities such as underwater blasting and pile driving, an autonomous system was designed to record underwater acoustic signals. The underwater sound recording device (USR allows for connections of two hydrophones or other dynamic pressure sensors, filters high frequency noise out of the collected signals, has a gain that can be independently set for each sensor, and allows for 2 h of data collection. Two versions of the USR were created: a submersible model deployable to a maximum depth of 300 m, and a watertight but not fully submersible model. Tests were performed on the USR in the laboratory using a data acquisition system to send single-frequency sinusoidal voltages directly to each component. These tests verified that the device operates as designed and performs as well as larger commercially available data acquisition systems, which are not suited for field use. On average, the designed gain values differed from the actual measured gain values by about 0.35 dB. A prototype of the device was used in a case study to measure blast pressures while investigating the effect of underwater rock blasting on juvenile Chinook salmon and rainbow trout. In the case study, maximum positive pressure from the blast was found to be significantly correlated with frequency of injury for individual fish. The case study also demonstrated that the device withstood operation in harsh environments, making it a valuable tool for collecting field measurements.

  12. Passive aquatic listener (PAL): An adoptive underwater acoustic recording system for the marine environment

    International Nuclear Information System (INIS)

    Anagnostou, Marios N.; Nystuen, Jeffrey A.; Anagnostou, Emmanouil N.; Papadopoulos, Anastasios; Lykousis, Vassilios

    2011-01-01

    The ambient sound field in the ocean is a combination of natural and manmade sounds. Consequently, the interpretation of the ambient sound field can be used to quantify these processes. In the frequency range from 1 to 50 kHz, the general character of ocean ambient sound is a slowly changing background that is closely associated with local wind speed, interspersed with shorter time scale events such as rain storms, ships and animal calls. At lower frequencies the underwater ambient sound budget includes geologically generated sound activities including underwater volcanic eruptions, seismic and seepage faults that generate bubbles, etc. that can also potentially be classified and quantified. Acoustic data are collected on hydrophones. Hydrophones are simple, robust sensors that can be deployed on most ocean instrumentation systems including surface or sub-surface moorings, bottom mounted systems, drifters, ARGO floats or autonomous underwater platforms. A dedicated oceanic underwater recorder called a passive acoustic listener (PAL) has been developed. A principal issue is to accurately distinguish different sound sources so that they can be quantified as part of a sound budget, and then quantified if appropriate. Based on ongoing data collected from the Poseidon II network the retrieval potential of multi-parameters from underwater sound, including meteorological (i.e., precipitation and winds) and in general geophysical, anthropogenetic (i.e., ships, submarines, etc.) and biological (whales, etc.) sources is presented.

  13. Carbon Nanotube Underwater Acoustic Thermophone

    Science.gov (United States)

    2016-09-23

    Attorney Docket No. 300009 1 of 8 A CARBON NANOTUBE UNDERWATER ACOUSTIC THERMOPHONE STATEMENT OF GOVERNMENT INTEREST [0001] The...the Invention [0003] The present invention is an acoustically transparent carbon nanotube thermophone. (2) Description of the Prior Art [0004...amplitude of the resulting sound waves. [0006] Recently, there has been development of underwater acoustic carbon nanotube (CNT) yarn sheets capable

  14. Underwater gas tornado

    Science.gov (United States)

    Byalko, Alexey V.

    2013-07-01

    We present the first experimental observation of a new hydrodynamic phenomenon, the underwater tornado. Simple measurements show that the tornado forms a vortex of the Rankine type, i.e. the rising gas rotates as a solid body and the liquid rotates with a velocity decreasing hyperbolically with the radius. We obtain the dependence of the tornado radius a on the gas stream value j theoretically: a ∼ j2/5. Processing of a set of experiments yielded the value 0.36 for the exponent in this expression. We also report the initial stages of the theoretical study of this phenomenon.

  15. Intermittent Noise Induces Physiological Stress in a Coastal Marine Fish

    OpenAIRE

    Nichols, Tye A.; Anderson, Todd W.; Širović, Ana

    2015-01-01

    Anthropogenic noise in the ocean has increased substantially in recent decades, and motorized vessels produce what is likely the most common form of underwater noise pollution. Noise has the potential to induce physiological stress in marine fishes, which may have negative ecological consequences. In this study, physiological effects of increased noise (playback of boat noise recorded in the field) on a coastal marine fish (the giant kelpfish, Heterostichus rostratus) were investigated by mea...

  16. Classroom Noise and Teachers' Voice Production

    Science.gov (United States)

    Rantala, Leena M.; Hakala, Suvi; Holmqvist, Sofia; Sala, Eeva

    2015-01-01

    Purpose: The aim of this study was to research the associations between noise (ambient and activity noise) and objective metrics of teachers' voices in real working environments (i.e., classrooms). Method: Thirty-two female and 8 male teachers from 14 elementary schools were randomly selected for the study. Ambient noise was measured during breaks…

  17. A Near Real-Time Seismic Exploration and Monitoring (i.e., Ambient Seismic Noise Interferometry) Solution Based Upon a Novel "At the Edge" Approach that Leverages Commercially Available Digitizers, Embedded Systems, and an Open-Source Big Data Architecture

    Science.gov (United States)

    Sepulveda, F.; Thangraj, J. S.; Quiros, D.; Pulliam, J.; Queen, J. H.; Queen, M.; Iovenitti, J. L.

    2017-12-01

    Seismic interferometry that makes use of ambient noise requires that cross-correlations of data recorded at two or more stations be stacked over a "long enough" time interval that off-axis sources cancel and the estimated inter-station Green's function converges to the actual function. However, the optimal length of the recording period depends on the characteristics of ambient noise at the site, which vary over time and are therefore not known before data acquisition. Data acquisition parameters cannot be planned in ways that will ensure success while minimizing cost and effort. Experiment durations are typically either too long or too short. Automated, in-field processing can provide inter-station Green's functions in near-real-time, allowing for the immediate evaluation of results and enabling operators to alter data acquisition parameters before demobilizing. We report on the design, system integration, and testing of a strategy for the automation of data acquisition, distribution, and processing of ambient noise using industry-standard, widely-available instrumentation (Reftek 130-01 digitizers and 4.5 Hz geophones). Our solution utilizes an inexpensive embedded system (Raspberry Pi 3), which is configured to acquire data from the Reftek and insert it into a big data store called Apache Cassandra. Cassandra distributes and maintains up-to-date copies of the data, through a WiFi network, as defined by tunable consistency levels and replication factors thus allowing for efficient multi-station computations. At regular intervals, data is extracted from Cassandra and is used to compute Green's functions for all receiver pairs. Results are reviewed and progress toward convergence can be assessed. We successfully tested a 20-node prototype of what we call the "Raspberry Pi-Enhanced Reftek" (RaPiER) array at the Soda Lake Geothermal Field in Nevada in June 2017. While intermittent problems with the WiFi network interfered with the real-time data delivery from some

  18. Noise exposure under hyperbaric conditions

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Objective evidence exists that divers demonstrate a hearing deficit greater than would be expected from ageing effects alone. Deafness in divers may be caused by a number of factors other than exposure to excessive noise levels, eg barotrauma, ear infection etc. This review concentrates on the concern that exposure of commercial divers to noise while at work may cause a hearing deficit. Sound pressure levels recorded both underwater and in diving chambers often exceed those allowable to workers onshore. However, the sound perceived by the diver is modified both in amplitude and in frequency when he is either underwater or in pressurised chambers. Broadly the effect of this modification is to attenuate the sound and thus offer some protection from high noise levels. The degree of attentuation varies with the frequency of the sound, however it is also possible under specific conditions associated with gas density for the sensitivity to particular frequencies to be amplified above that for normal atmospheric air. The levels of sound observed from some underwater tools are of concern even after allowing for a significant de-sensitisation of the divers` hearing. Reports of tinnitus and temporary hearing loss following a dive are sure signs that the noise levels have been harmful. It is not possible at present to describe risk criteria for hearing damage due to noise exposure associated with diving. (author)

  19. OFDM for underwater acoustic communications

    CERN Document Server

    Zhou, Shengli

    2014-01-01

    A blend of introductory material and advanced signal processing and communication techniques, of critical importance to underwater system and network development This book, which is the first to describe the processing techniques central to underwater OFDM, is arranged into four distinct sections: First, it describes the characteristics of underwater acoustic channels, and stresses the difference from wireless radio channels. Then it goes over the basics of OFDM and channel coding. The second part starts with an overview of the OFDM receiver, and develops various modules for the receiver des

  20. Design and implementation of a shielded underwater vector sensor for laboratory environments.

    Science.gov (United States)

    Barnard, Andrew R; Hambric, Stephen A

    2011-12-01

    Underwater acoustic vector sensors, for measuring acoustic intensity, are typically used in open water where electromagnetic interference (EMI) is generally not a contributor to overall background noise. However, vector sensors are also useful in a laboratory setting where EMI can be a limiting factor at low frequencies. An underwater vector sensor is designed and built with specific care for EMI immunity. The sensor, and associated signal processing, is shown to reduce background noise at EMI frequencies by 10-50 dB and 10-20 dB across the entire frequency bandwidth, as compared to an identical unshielded vector sensor. © 2011 Acoustical Society of America

  1. Ambient Space and Ambient Sensation

    DEFF Research Database (Denmark)

    Schmidt, Ulrik

    The ambient is the aesthetic production of the sensation of being surrounded. As a concept, 'ambient' is mostly used in relation to the music genre 'ambient music' and Brian Eno's idea of environmental background music. However, the production of ambient sensations must be regarded as a central...

  2. Underwater plasma arc cutting

    International Nuclear Information System (INIS)

    Leautier, R.; Pilot, G.

    1991-01-01

    This report describes the work done to develop underwater plasma arc cutting techniques, to characterise aerosols from cutting operations on radioactive and non-radioactive work-pieces, and to develop suitable ventilation and filtration techniques. The work has been carried out in the framework of a contract between CEA-CEN Cadarache and the Commission of European Communities. Furthermore, this work has been carried out in close cooperation with CEA-CEN Saclay mainly for secondary emissions and radioactive analysis. The contract started in May 1986 and was completed in December 1988 by a supplementary agreement. This report has been compiled from several progress reports submitted during the work period, contains the main findings of the work and encloses the results of comparative tests on plasma arc cutting

  3. Long-term exposure to ambient air pollution and traffic noise and incident hypertension in seven cohorts of the European study of cohorts for air pollution effects (ESCAPE).

    Science.gov (United States)

    Fuks, Kateryna B; Weinmayr, Gudrun; Basagaña, Xavier; Gruzieva, Olena; Hampel, Regina; Oftedal, Bente; Sørensen, Mette; Wolf, Kathrin; Aamodt, Geir; Aasvang, Gunn Marit; Aguilera, Inmaculada; Becker, Thomas; Beelen, Rob; Brunekreef, Bert; Caracciolo, Barbara; Cyrys, Josef; Elosua, Roberto; Eriksen, Kirsten Thorup; Foraster, Maria; Fratiglioni, Laura; Hilding, Agneta; Houthuijs, Danny; Korek, Michal; Künzli, Nino; Marrugat, Jaume; Nieuwenhuijsen, Mark; Östenson, Claes-Göran; Penell, Johanna; Pershagen, Göran; Raaschou-Nielsen, Ole; Swart, Wim J R; Peters, Annette; Hoffmann, Barbara

    2017-04-01

    We investigated whether traffic-related air pollution and noise are associated with incident hypertension in European cohorts. We included seven cohorts of the European study of cohorts for air pollution effects (ESCAPE). We modelled concentrations of particulate matter with aerodynamic diameter ≤2.5 µm (PM2.5), ≤10 µm (PM10), >2.5, and ≤10 µm (PMcoarse), soot (PM2.5 absorbance), and nitrogen oxides at the addresses of participants with land use regression. Residential exposure to traffic noise was modelled at the facade according to the EU Directive 2002/49/EC. We assessed hypertension as (i) self-reported and (ii) measured (systolic BP ≥ 140 mmHg or diastolic BP ≥ 90 mmHg or intake of BP lowering medication (BPLM). We used Poisson regression with robust variance estimation to analyse associations of traffic-related exposures with incidence of hypertension, controlling for relevant confounders, and combined the results from individual studies with random-effects meta-analysis. Among 41 072 participants free of self-reported hypertension at baseline, 6207 (15.1%) incident cases occurred within 5-9 years of follow-up. Incidence of self-reported hypertension was positively associated with PM2.5 (relative risk (RR) 1.22 [95%-confidence interval (CI):1.08; 1.37] per 5 µg/m³) and PM2.5 absorbance (RR 1.13 [95% CI:1.02; 1.24] per 10 - 5m - 1). These estimates decreased slightly upon adjustment for road traffic noise. Road traffic noise was weakly positively associated with the incidence of self-reported hypertension. Among 10 896 participants at risk, 3549 new cases of measured hypertension occurred. We found no clear associations with measured hypertension. Long-term residential exposures to air pollution and noise are associated with increased incidence of self-reported hypertension. Published on behalf of the European Society of Cardiology. All rights reserved. © The Author 2016. For Permissions, please email: journals.permissions@oup.com.

  4. Safety aspects for underwater vehicles

    Digital Repository Service at National Institute of Oceanography (India)

    Madhan, R.; Navelkar, G.S.; Desa, E.S.; Afzulpurkar, S.; Prabhudesai, S.P.; Dabholkar, N.; Mascarenhas, A.A.M.Q.; Maurya, P.

    . This stresses for implementation of multiple safety measures of a high degree so that the platform operates continuously in a fail-safe mode. This paper discusses issues on safety measures implemented on the autonomous underwater platforms namely MAYA AUV...

  5. A Validation Process for Underwater Localization Algorithms

    Directory of Open Access Journals (Sweden)

    Marc Hildebrandt

    2014-09-01

    Full Text Available This paper describes the validation process of a localization algorithm for underwater vehicles. In order to develop new localization algorithms, it is essential to characterize them with regard to their accuracy, long-term stability and robustness to external sources of noise. This is only possible if a gold-standard reference localization (GSRL is available against which any new localization algorithm (NLA can be tested. This process requires a vehicle which carries all the required sensor and processing systems for both the GSRL and the NLA. This paper will show the necessity of such a validation process, briefly sketch the test vehicle and its capabilities, describe the challenges in computing the localizations of both the GSRL and the NLA simultaneously for comparison, and conclude with experimental data of real-world trials.

  6. Noise suppression by noise

    OpenAIRE

    Vilar, J. M. G. (José M. G.), 1972-; Rubí Capaceti, José Miguel

    2001-01-01

    We have analyzed the interplay between an externally added noise and the intrinsic noise of systems that relax fast towards a stationary state, and found that increasing the intensity of the external noise can reduce the total noise of the system. We have established a general criterion for the appearance of this phenomenon and discussed two examples in detail.

  7. QFD-based conceptual design of an autonomous underwater robot

    Directory of Open Access Journals (Sweden)

    Thip Pasawang

    2015-12-01

    Full Text Available Autonomous underwater robots in the past few years have been designed according to the individual concepts and experiences of the researchers. To design a robot, which meets all the requirements of potential users, is an advanced work. Hence, a systematic design method that could include users’ preferences and requirements is needed. This paper presents the quality function deployment (QFD technique to design an autonomous underwater robot focusing on the Thai Navy military mission. Important user requirements extracted from the QFD method are the ability to record videos, operating at depth up to 10 meters, the ability to operate remotely with cable and safety concerns related to water leakages. Less important user requirements include beauty, using renewable energy, operating remotely with radio and ability to work during night time. The important design parameters derived from the user requirements are a low cost-controller, an autonomous control algorithm, a compass sensor and vertical gyroscope, and a depth sensor. Of low-importance ranked design parameters include the module design, use clean energy, a low noise electric motor, remote surveillance design, a pressure hull, and a beautiful hull form design. The study results show the feasibility of using QFD techniques to systematically design the autonomous underwater robot to meet user requirements. Mapping between the design and expected parameters and a conceptual drafting design of an autonomous underwater robot are also presented.

  8. Underwater optical wireless communication network

    Science.gov (United States)

    Arnon, Shlomi

    2010-01-01

    The growing need for underwater observation and subsea monitoring systems has stimulated considerable interest in advancing the enabling technologies of underwater wireless communication and underwater sensor networks. This communication technology is expected to play an important role in investigating climate change, in monitoring biological, biogeochemical, evolutionary, and ecological changes in the sea, ocean, and lake environments, and in helping to control and maintain oil production facilities and harbors using unmanned underwater vehicles (UUVs), submarines, ships, buoys, and divers. However, the present technology of underwater acoustic communication cannot provide the high data rate required to investigate and monitor these environments and facilities. Optical wireless communication has been proposed as the best alternative to meet this challenge. Models are presented for three kinds of optical wireless communication links: (a) a line-of-sight link, (b) a modulating retroreflector link, and (c) a reflective link, all of which can provide the required data rate. We analyze the link performance based on these models. From the analysis, it is clear that as the water absorption increases, the communication performance decreases dramatically for the three link types. However, by using the scattered light it was possible to mitigate this decrease in some cases. It is concluded from the analysis that a high-data-rate underwater optical wireless network is a feasible solution for emerging applications such as UUV-to-UUV links and networks of sensors, and extended ranges in these applications could be achieved by applying a multi-hop concept.

  9. Classroom Noise and Teachers' Voice Production.

    Science.gov (United States)

    Rantala, Leena M; Hakala, Suvi; Holmqvist, Sofia; Sala, Eeva

    2015-10-01

    The aim of this study was to research the associations between noise (ambient and activity noise) and objective metrics of teachers' voices in real working environments (i.e., classrooms). Thirty-two female and 8 male teachers from 14 elementary schools were randomly selected for the study. Ambient noise was measured during breaks in unoccupied classrooms and, likewise, the noise caused by pupils' activity during lessons. Voice samples were recorded before and after a working day. Voice variables measured were sound pressure level (voice SPL), fundamental frequency, jitter, shimmer, and the tilt of the sound spectrum slope (alpha ratio). The ambient noise correlated most often with the fundamental frequency of men and voice SPL, whereas activity noise correlated with the alpha ratio and perturbation values. Teachers working in louder ambient noise spoke more loudly before work than those working in lower noise levels. Voice variables generally changed less during work among teachers working in loud activity noise than among those working in lower noise levels. Ambient and activity noises affect teachers' voice use. Under loud ambient noise teachers seem to speak habitually loudly, and under loud activity noise teachers' ability to react to loading deteriorates.

  10. Can we use the q-Gaussian of ambient noise fluctuations as a vulnerability index? A case study in Cultural Heritage buildings

    Science.gov (United States)

    Vallianatos, Filippos; Koutalonis, Ioannis; Moisidi, Margarita; Chatzopoulos, Georgios

    2018-05-01

    In this work we study in terms of Tsallis statistical mechanics the properties of microtremors' fluctuations in two church bell towers, which are monuments of cultural heritage, in the city of Chania (Crete, Greece). We have shown that fluctuations of ambient vibrations recordings in the Church tower bells follow a q-Gaussian distribution. The behavior of Tsallis q parameter with the level (high) of the measuring point within the tower and the amplification factors at that points as extracted from horizontal-to-vertical (HVSR) spectral ratios are presented and discussed. Since q decreases as the amplification factor increases, we could suggest q as a vulnerability index, where, as q decreases approaching unity, then the structural system is getting more vulnerable. The latter approach suggests that introducing ideas of Tsallis statistics could be useful in characterizing extremely complex processes as that governed the estimation of seismic vulnerability in which a multidisciplinary approach is required.

  11. Ambient Space and Ambient Sensation

    DEFF Research Database (Denmark)

    Schmidt, Ulrik

    The ambient is the aesthetic production of the sensation of being surrounded. As a concept, 'ambient' is mostly used in relation to the music genre 'ambient music' and Brian Eno's idea of environmental background music. However, the production of ambient sensations must be regarded as a central......, dehierarchization, ubiquity and the production of unfocused sensations in contrast to the conventional notion of the aesthetic experience as a focused contemplation of a stationary object....

  12. Underwater cutting techniques developments

    International Nuclear Information System (INIS)

    Bach, F.-W.

    1990-01-01

    The primary circuit structures of different nuclear powerplants are constructed out of stainless steels, ferritic steels, plated ferritic steels and alloys of aluminium. According to the level of the specific radiation of these structures, it is necessary for dismantling to work with remote controlled cutting techniques. The most successful way to protect the working crew against exposure of radiation is to operate underwater in different depths. The following thermal cutting processes are more or less developed to work under water: For ferritic steels only - flame cutting; For ferritic steels, stainless steels, cladded steels and aluminium alloys - oxy-arc-cutting, arc-waterjet-cutting with a consumable electrode, arc-saw-cutting, plasma-arc-cutting and plasma-arc-saw. The flame cutting is a burning process, all the other processes are melt-cutting processes. This paper explains the different techniques, giving a short introduction of the theory, a discussion of the possibilities with the advantages and disadvantages of these processes giving a view into the further research work in this interesting field. (author)

  13. Characterization of Underwater Sounds Produced by a Backhoe Dredge Excavating Rock and Gravel

    Science.gov (United States)

    2012-12-01

    source levels of the 2,700-m3 hopper dredge The City of Westminster operating on the Hastings Shingle and calculated the broadband source level to 186...Assessment of underwater noise from dredging operations on the Hasting Shingle Bank. Report No. Subacoustech 758R0137. Popper, A. N. 2003. Effects of

  14. Design of Autonomous Underwater Vehicle

    Directory of Open Access Journals (Sweden)

    Tadahiro Hyakudome

    2011-03-01

    Full Text Available There are concerns about the impact that global warming will have on our environment, and which will inevitably result in expanding deserts and rising water levels. While a lot of underwater vehicles are utilized, AUVs (Autonomous Underwater Vehicle were considered and chosen, as the most suitable tool for conduction survey concerning these global environmental problems. AUVs can comprehensive survey because the vehicle does not have to be connected to the support vessel by tether cable. When such underwater vehicles are made, it is necessary to consider about the following things. 1 Seawater and Water Pressure Environment, 2 Sink, 3 There are no Gas or Battery Charge Stations, 4 Global Positioning System cannot use, 5 Radio waves cannot use. In the paper, outline of above and how deal about it are explained.

  15. Underwater measurements of muon intensity

    Science.gov (United States)

    Fedorov, V. M.; Pustovetov, V. P.; Trubkin, Y. A.; Kirilenkov, A. V.

    1985-01-01

    Experimental measurements of cosmic ray muon intensity deep underwater aimed at determining a muon absorption curve are of considerable interest, as they allow to reproduce independently the muon energy spectrum at sea level. The comparison of the muon absorption curve in sea water with that in rock makes it possible to determine muon energy losses caused by nuclear interactions. The data available on muon absorption in water and that in rock are not equivalent. Underground measurements are numerous and have been carried out down to the depth of approx. 15km w.e., whereas underwater muon intensity have been measured twice and only down to approx. 3km deep.

  16. Model scale measurements of surface ship radiated flow noise

    NARCIS (Netherlands)

    Jong, C.A.F.; Bosschers, J.; Hasenpflug, H.

    2009-01-01

    Advances in weapon and sensor capabilities are driving an increased interest in the control of underwater signatures of naval platforms. The control of machinery and propeller noise is well understood, but there is a shortfall of knowledge of the mechanisms that govern noise due to the flow around

  17. Underwater image quality enhancement of sea cucumbers based on improved histogram equalization and wavelet transform

    Directory of Open Access Journals (Sweden)

    Xi Qiao

    2017-09-01

    Full Text Available Sea cucumbers usually live in an environment where lighting and visibility are generally not controllable, which cause the underwater image of sea cucumbers to be distorted, blurred, and severely attenuated. Therefore, the valuable information from such an image cannot be fully extracted for further processing. To solve the problems mentioned above and improve the quality of the underwater images of sea cucumbers, pre-processing of a sea cucumber image is attracting increasing interest. This paper presents a new method based on contrast limited adaptive histogram equalization and wavelet transform (CLAHE-WT to enhance the sea cucumber image quality. CLAHE was used to process the underwater image for increasing contrast based on the Rayleigh distribution, and WT was used for de-noising based on a soft threshold. Qualitative analysis indicated that the proposed method exhibited better performance in enhancing the quality and retaining the image details. For quantitative analysis, the test with 120 underwater images showed that for the proposed method, the mean square error (MSE, peak signal to noise ratio (PSNR, and entropy were 49.2098, 13.3909, and 6.6815, respectively. The proposed method outperformed three established methods in enhancing the visual quality of sea cucumber underwater gray image.

  18. An Underwater Color Image Quality Evaluation Metric.

    Science.gov (United States)

    Yang, Miao; Sowmya, Arcot

    2015-12-01

    Quality evaluation of underwater images is a key goal of underwater video image retrieval and intelligent processing. To date, no metric has been proposed for underwater color image quality evaluation (UCIQE). The special absorption and scattering characteristics of the water medium do not allow direct application of natural color image quality metrics especially to different underwater environments. In this paper, subjective testing for underwater image quality has been organized. The statistical distribution of the underwater image pixels in the CIELab color space related to subjective evaluation indicates the sharpness and colorful factors correlate well with subjective image quality perception. Based on these, a new UCIQE metric, which is a linear combination of chroma, saturation, and contrast, is proposed to quantify the non-uniform color cast, blurring, and low-contrast that characterize underwater engineering and monitoring images. Experiments are conducted to illustrate the performance of the proposed UCIQE metric and its capability to measure the underwater image enhancement results. They show that the proposed metric has comparable performance to the leading natural color image quality metrics and the underwater grayscale image quality metrics available in the literature, and can predict with higher accuracy the relative amount of degradation with similar image content in underwater environments. Importantly, UCIQE is a simple and fast solution for real-time underwater video processing. The effectiveness of the presented measure is also demonstrated by subjective evaluation. The results show better correlation between the UCIQE and the subjective mean opinion score.

  19. Near surface structure of the North Anatolian Fault Zone near 30°E from Rayleigh and Love wave tomography using ambient seismic noise.

    Science.gov (United States)

    Taylor, G.; Rost, S.; Houseman, G. A.; Hillers, G.

    2017-12-01

    By utilising short period surface waves present in the noise field, we can construct images of shallow structure in the Earth's upper crust: a depth-range that is usually poorly resolved in earthquake tomography. Here, we use data from a dense seismic array (Dense Array for Northern Anatolia - DANA) deployed across the North Anatolian Fault Zone (NAFZ) in the source region of the 1999 magnitude 7.6 Izmit earthquake in western Turkey. The NAFZ is a major strike-slip system that extends 1200 km across northern Turkey and continues to pose a high level of seismic hazard, in particular to the mega-city of Istanbul. We obtain maps of group velocity variation using surface wave tomography applied to short period (1- 6 s) Rayleigh and Love waves to construct high-resolution images of SV and SH-wave velocity in the upper 5 km of a 70 km x 35 km region centred on the eastern end of the fault segment that ruptured in the 1999 Izmit earthquake. The average Rayleigh wave group velocities in the region vary between 1.8 km/s at 1.5 s period, to 2.2 km/s at 6 s period. The NAFZ bifurcates into northern and southern strands in this region; both are active but only the northern strand ruptured in the 1999 event. The signatures of both the northern and southern branches of the NAFZ are clearly associated with strong gradients in seismic velocity that also denote the boundaries of major tectonic units. This observation implies that the fault zone exploits the pre-existing structure of the Intra-Pontide suture zone. To the north of the NAFZ, we observe low S-wave velocities ( 2.0 km/s) associated with the unconsolidated sediments of the Adapazari basin, and blocks of weathered terrigenous clastic sediments. To the south of the northern branch of the NAFZ in the Armutlu block, we detect higher velocities ( 2.9 km/s) associated with a shallow crystalline basement, in particular a block of metamorphosed schists and marbles that bound the northern branch of the NAFZ.

  20. Characterization of the Acoustic Field in Marine Environments with Anthropogenic Noise

    Science.gov (United States)

    Guan, Shane

    Most animals inhabit the aquatic environment are acoustical-oriented, due to the physical characteristics of water that favors sound transmission. Many aquatic animals depend on underwater sound to navigate, communicate, find prey, and avoid predators. The degradation of underwater acoustic environment due to human activities is expected to affected these animals' well-being and survival at the population level. This dissertation presents three original studies on the characteristics and behavior of underwater sound fields in three unique marine environments with anthropogenic noises. The first study examines the soundscape of the Chinese white dolphin habitat in Taiwan. Acoustic recordings were made at two coastal shallow water locations, Yunlin and Waisanding, in 2012. Results show that croaker choruses are dominant sound sources in the 1.2--2.4 kHz frequency band for both locations at night, and noises from container ships in the 150--300 Hz frequency band define the relative higher broadband sound levels at Yunlin. Results also illustrate interrelationships among different biotic, abiotic, and anthropogenic elements that shape the fine-scale soundscape in a coastal environment. The second study investigates the inter-pulse sound field during an open-water seismic survey in coastal shallow waters of the Arctic. The research uses continuous acoustic recordings collected from one bottom-mounted hydrophone deployed in the Beaufort Sea in summer 2012. Two quantitative methods were developed to examine the inter-pulse sound field characteristics and its dependence on source distances. Results show that inter-pulse sound field could raise the ambient noise floor by as much as 9 dB, depending on ambient condition and source distance. The third study examines the inter-ping sound field of simulated mid-frequency active sonar in deep waters off southern California in 2013 and 2014. The study used drifting acoustic recorder buoys to collect acoustic data during sonar

  1. Noise thermometer

    International Nuclear Information System (INIS)

    Von Brixy, H.; Kakuta, Tsunemi.

    1996-03-01

    The noise thermometry (NT) is a temperature measuring method by which the absolute temperature measurement can be performed with a very high accuracy and without any influence of ambient environments and of the thermal history of its NT sensor (electric resistor). Hence it is quite suitable for application as a standard thermometry to the in-situ temperature calibration of incore thermocouples. The KFA Juelich had played a pioneering role in the development of NT and applied the results successfully to the AVR for testing its feasibility. In this report, all about the NT including its principle, sensor elements and system configurations are presented together with the experiences in the AVR and the results of investigation to apply it to high temperature measurement. The NT can be adopted as a standard method for incore temperature measurement and in situ temperature calibration in the HTTR. (author). 85 refs

  2. Noise thermometer

    Energy Technology Data Exchange (ETDEWEB)

    Von Brixy, H. [Forschungszentrum Juelich GmbH (Germany); Kakuta, Tsunemi

    1996-03-01

    The noise thermometry (NT) is a temperature measuring method by which the absolute temperature measurement can be performed with a very high accuracy and without any influence of ambient environments and of the thermal history of its NT sensor (electric resistor). Hence it is quite suitable for application as a standard thermometry to the in-situ temperature calibration of incore thermocouples. The KFA Juelich had played a pioneering role in the development of NT and applied the results successfully to the AVR for testing its feasibility. In this report, all about the NT including its principle, sensor elements and system configurations are presented together with the experiences in the AVR and the results of investigation to apply it to high temperature measurement. The NT can be adopted as a standard method for incore temperature measurement and in situ temperature calibration in the HTTR. (author). 85 refs.

  3. Influence of range-gated intensifiers on underwater imaging system SNR

    Science.gov (United States)

    Wang, Xia; Hu, Ling; Zhi, Qiang; Chen, Zhen-yue; Jin, Wei-qi

    2013-08-01

    Range-gated technology has been a hot research field in recent years due to its high effective back scattering eliminating. As a result, it can enhance the contrast between a target and its background and extent the working distance of the imaging system. The underwater imaging system is required to have the ability to image in low light level conditions, as well as the ability to eliminate the back scattering effect, which means that the receiver has to be high-speed external trigger function, high resolution, high sensitivity, low noise, higher gain dynamic range. When it comes to an intensifier, the noise characteristics directly restrict the observation effect and range of the imaging system. The background noise may decrease the image contrast and sharpness, even covering the signal making it impossible to recognize the target. So it is quite important to investigate the noise characteristics of intensifiers. SNR is an important parameter reflecting the noise features of a system. Through the use of underwater laser range-gated imaging prediction model, and according to the linear SNR system theory, the gated imaging noise performance of the present market adopted super second generation and generation Ⅲ intensifiers were theoretically analyzed. Based on the active laser underwater range-gated imaging model, the effect to the system by gated intensifiers and the relationship between the system SNR and MTF were studied. Through theoretical and simulation analysis to the image intensifier background noise and SNR, the different influence on system SNR by super second generation and generation Ⅲ ICCD was obtained. Range-gated system SNR formula was put forward, and compared the different effect influence on the system by using two kind of ICCDs was compared. According to the matlab simulation, a detailed analysis was carried out theoretically. All the work in this paper lays a theoretical foundation to further eliminating back scattering effect, improving

  4. Calibration of Underwater Sound Transducers

    OpenAIRE

    H.R.S. Sastry

    1983-01-01

    The techniques of calibration of underwater sound transducers for farfield, near-field and closed environment conditions are reviewed in this paper .The design of acoustic calibration tank is mentioned. The facilities available at Naval Physical & Oceanographic Laboratory, Cochin for calibration of transducers are also listed.

  5. Underwater nuclear power plant structure

    International Nuclear Information System (INIS)

    Severs, S.; Toll, H.V.

    1982-01-01

    A structure for an underwater nuclear power generating plant comprising a triangular platform formed of tubular leg and truss members upon which are attached one or more large spherical pressure vessels and one or more small cylindrical auxiliary pressure vessels. (author)

  6. Underwater Robots Surface in Utah

    Science.gov (United States)

    Hurd, Randy C.; Hacking, Kip S.; Damarjian, Jennifer L.; Wright, Geoffrey A.; Truscott, Tadd

    2015-01-01

    Underwater robots (or ROVs: Remotely Operated Vehicles as they are typically called in industry) have recently become a very popular instructional STEM activity. Nationally, ROVs have been used in science and technology classrooms for several years in cities such as Seattle, San Diego, Virginia Beach, and other coastal areas. In the past two…

  7. Det ambiente

    DEFF Research Database (Denmark)

    Schmidt, Ulrik

    Om begrebet "det ambiente", der beskriver, hvad der sker, når vi fornemmer baggrundsmusikkens diskrete beats, betragter udsigten gennem panoramavinduet eller tager 3D-brillerne på og læner os tilbage i biografsædet. Bogen analyserer, hvorfan ambiente oplevelser skabes, og hvilke konsekvenser det...

  8. Localization of Energy Harvesting Empowered Underwater Optical Wireless Sensor Networks

    KAUST Repository

    Saeed, Nasir

    2017-12-20

    In this paper, a received signal strength (RSS) based localization technique is developed for energy harvesting underwater optical wireless sensor networks (EH-UOWSNs), where the optical noise sources and channel impairments of seawater pose significant challenges for range estimation. Energy limitation is another major problem due to the limited battery power and difficulty in replacing or recharging the battery of an underwater sensor node. In the proposed framework, sensor nodes with insufficient battery, harvest the energy and starts communicating once it has sufficient energy storage. Network localization is carried out by measuring the RSSs of active nodes, which are modeled based on the underwater optical communication channel characteristics. Thereafter, block kernel matrices are computed for the RSS based range measurements. Unlike the traditional shortest-path approach, the proposed technique reduces the shortest path estimation for each block kernel matrix. Once the complete block kernel matrices are available, a closed form localization technique is developed to find the location of every optical sensor node in the network. Furthermore, an analytical expression for Cramer Rao lower bound (CRLB) is derived as a benchmark to compare the localization performance of the proposed technique. Finally, extensive simulations show that the proposed technique outperforms the well-known network localization techniques.

  9. Underwater Electromagnetic Sensor Networks, Part II: Localization and Network Simulations

    Directory of Open Access Journals (Sweden)

    Javier Zazo

    2016-12-01

    Full Text Available In the first part of the paper, we modeled and characterized the underwater radio channel in shallowwaters. In the second part,we analyze the application requirements for an underwaterwireless sensor network (U-WSN operating in the same environment and perform detailed simulations. We consider two localization applications, namely self-localization and navigation aid, and propose algorithms that work well under the specific constraints associated with U-WSN, namely low connectivity, low data rates and high packet loss probability. We propose an algorithm where the sensor nodes collaboratively estimate their unknown positions in the network using a low number of anchor nodes and distance measurements from the underwater channel. Once the network has been self-located, we consider a node estimating its position for underwater navigation communicating with neighboring nodes. We also propose a communication system and simulate the whole electromagnetic U-WSN in the Castalia simulator to evaluate the network performance, including propagation impairments (e.g., noise, interference, radio parameters (e.g., modulation scheme, bandwidth, transmit power, hardware limitations (e.g., clock drift, transmission buffer and complete MAC and routing protocols. We also explain the changes that have to be done to Castalia in order to perform the simulations. In addition, we propose a parametric model of the communication channel that matches well with the results from the first part of this paper. Finally, we provide simulation results for some illustrative scenarios.

  10. Power characterization of THUNDER actuators as underwater propulsors

    Science.gov (United States)

    Niezrecki, Christopher; Balakrishnan, Sivakumar

    2001-08-01

    Piezoelectric actuators have been used for active vibration control, noise suppression, health monitoring, etc. The large appeal in using smart material actuators stems from their high mechanical energy density. A relatively new actuator (THUNDER) has overcome the displacement hurdles that have plagued traditional piezoelectric based actuators. It is capable of providing a displacement on order of 0.5 cm. This allows the actuator to be used in some underwater applications, such as propulsion. To date the electrical power consumption and electromechanical efficiency of these actuators has not been quantified; specifically, applied as underwater propulsors. Some of the challenges in obtaining this information stems from the actuator's non traditional actuating architecture, high voltage requirements, and its electrical non-linearity. The work presented experimentally determines the electrical power consumption and mechanical displacement of THUNDER actuators used as underwater propulsors. It is found that the electrical power consumption of the clamshell actuator investigated is significantly less than that consumed by other autonomous under water vehicles. The potential thrust generated by such a device remains to be quantified.

  11. Autonomous Underwater Vehicle Magnetic Mapping System

    Science.gov (United States)

    Steigerwalt, R.; Johnson, R. M.; Trembanis, A. C.; Schmidt, V. E.; Tait, G.

    2012-12-01

    An Autonomous Underwater Vehicle (AUV) Magnetic Mapping (MM) System has been developed and tested for military munitions detection as well as pipeline locating, wreck searches, and geologic surveys in underwater environments. The system is comprised of a high sensitivity Geometrics G-880AUV cesium vapor magnetometer integrated with a Teledyne-Gavia AUV and associated Doppler enabled inertial navigation further utilizing traditional acoustic bathymetric and side scan imaging. All onboard sensors and associated electronics are managed through customized crew members to autonomously operate through the vehicles primary control module. Total field magnetic measurements are recorded with asynchronous time-stamped data logs which include position, altitude, heading, pitch, roll, and electrical current usage. Pre-planned mission information can be uploaded to the system operators to define data collection metrics including speed, height above seafloor, and lane or transect spacing specifically designed to meet data quality objectives for the survey. As a result of the AUVs modular design, autonomous navigation and rapid deployment capabilities, the AUV MM System provides cost savings over current surface vessel surveys by reducing the mobilization/demobilization effort, thus requiring less manpower for operation and reducing or eliminating the need for a surface support vessel altogether. When the system completes its mission, data can be remotely downloaded via W-LAN and exported for use in advanced signal processing platforms. Magnetic compensation software has been concurrently developed to accept electrical current measurements directly from the AUV to address distortions from permanent and induced magnetization effects on the magnetometer. Maneuver and electrical current compensation terms can be extracted from the magnetic survey missions to perform automated post-process corrections. Considerable suppression of system noise has been observed over traditional

  12. Det Ambiente

    DEFF Research Database (Denmark)

    Schmidt, Ulrik

    Det ambiente er iscenesættelsen af en karakteristisk sanseoplevelse, der er kendetegnet ved fornemmelsen af at være omgivet. I dag bliver begrebet om det ambiente mest anvendt i forbindelse med musikgenren ’ambient musik’. Det ambiente er dog ikke essentielt knyttet til det musikalske, men må...... forstås som et betydeligt bredere fænomen i den moderne æstetiske kultur, der spiller en væsentlig rolle i oplevelsen af moderne transportformer, arkitektur, film, lydkunst, installationskunst og digitale multimedieiscenesættelser. En forståelse af det ambiente er derfor centralt for forståelsen af en...... moderne æstetiseret oplevelseskultur i almindelighed. Da det ambiente ikke hidtil har været gjort til genstand for en mere indgående teoretisk behandling, er der dog stor usikkerhed omkring, hvad fænomenet overhovedet indebærer. Hovedformålet med Det ambiente – Sansning, medialisering, omgivelse er derfor...

  13. Vessel generator noise as a settlement cue for marine biofouling species.

    Science.gov (United States)

    McDonald, J I; Wilkens, S L; Stanley, J A; Jeffs, A G

    2014-01-01

    Underwater noise is increasing globally, largely due to increased vessel numbers and international ocean trade. Vessels are also a major vector for translocation of non-indigenous marine species which can have serious implications for biosecurity. The possibility that underwater noise from fishing vessels may promote settlement of biofouling on hulls was investigated for the ascidian Ciona intestinalis. Spatial differences in biofouling appear to be correlated with spatial differences in the intensity and frequency of the noise emitted by the vessel's generator. This correlation was confirmed in laboratory experiments where C. intestinalis larvae showed significantly faster settlement and metamorphosis when exposed to the underwater noise produced by the vessel generator. Larval survival rates were also significantly higher in treatments exposed to vessel generator noise. Enhanced settlement attributable to vessel generator noise may indicate that vessels not only provide a suitable fouling substratum, but vessels running generators may be attracting larvae and enhancing their survival and growth.

  14. The Modular Optical Underwater Survey System

    Directory of Open Access Journals (Sweden)

    Ruhul Amin

    2017-10-01

    Full Text Available The Pacific Islands Fisheries Science Center deploys the Modular Optical Underwater Survey System (MOUSS to estimate the species-specific, size-structured abundance of commercially-important fish species in Hawaii and the Pacific Islands. The MOUSS is an autonomous stereo-video camera system designed for the in situ visual sampling of fish assemblages. This system is rated to 500 m and its low-light, stereo-video cameras enable identification, counting, and sizing of individuals at a range of 0.5–10 m. The modular nature of MOUSS allows for the efficient and cost-effective use of various imaging sensors, power systems, and deployment platforms. The MOUSS is in use for surveys in Hawaii, the Gulf of Mexico, and Southern California. In Hawaiian waters, the system can effectively identify individuals to a depth of 250 m using only ambient light. In this paper, we describe the MOUSS’s application in fisheries research, including the design, calibration, analysis techniques, and deployment mechanism.

  15. Network Computing for Distributed Underwater Acoustic Sensors

    Science.gov (United States)

    2014-03-31

    Physical layer in UASNs Our main investigations are about underwater communications using acoustic waves. Elec- tromagnetic and optical waves do not...Shengli, Z., and Jun-Hong, C. (2008), Prospects and problems of wireless communication for underwater sensor networks, Wirel. Commun . Mob. Comput., 8(8... Wireless Communications , 9(9), 2934–2944. [21] Pompili, D. and Akyildiz, I. (2010), A multimedia cross-layer protocol for underwater acoustic sensor networks

  16. Cooperative OFDM underwater acoustic communications

    CERN Document Server

    Cheng, Xilin; Cheng, Xiang

    2016-01-01

    Following underwater acoustic channel modeling, this book investigates the relationship between coherence time and transmission distances. It considers the power allocation issues of two typical transmission scenarios, namely short-range transmission and medium-long range transmission. For the former scenario, an adaptive system is developed based on instantaneous channel state information. The primary focus is on cooperative dual-hop orthogonal frequency division multiplexing (OFDM). This book includes the decomposed fountain codes designed to enable reliable communications with higher energy efficiency. It covers the Doppler Effect, which improves packet transmission reliability for effective low-complexity mirror-mapping-based intercarrier interference cancellation schemes capable of suppressing the intercarrier interference power level. Designed for professionals and researchers in the field of underwater acoustic communications, this book is also suitable for advanced-level students in electrical enginee...

  17. International Conference on Underwater Environment

    CERN Document Server

    Jaulin, Luc; Creuze, Vincent; Debese, Nathalie; Quidu, Isabelle; Clement, Benoît; Billon-Coat, Annick

    2016-01-01

    This volume constitutes the results of the International Conference on Underwater Environment, MOQESM’14, held at “Le Quartz” Conference Center in Brest, France, on October 14-15, 2014, within the framework of the 9th Sea Tech Week, International Marine Science and Technology Event. The objective of MOQESM'14 was to bring together researchers from both academia and industry, interested in marine robotics and hydrography with application to the coastal environment mapping and underwater infrastructures surveys. The common thread of the conference is the combination of technical control, perception, and localization, typically used in robotics, with the methods of mapping and bathymetry. The papers presented in this book focus on two main topics. Firstly, coastal and infrastructure mapping is addressed, focusing not only on hydrographic systems, but also on positioning systems, bathymetry, and remote sensing. The proposed methods rely on acoustic sensors such as side scan sonars, multibeam echo sounders, ...

  18. Optical Communication System for an Underwater Wireless Sensor Network

    Science.gov (United States)

    Gabriel, C.; Khalighi, A.; Bourennane, S.; Léon, P.; Rigaud, V.

    2012-04-01

    Seventy percent of the Earth is covered with water. Yet, we know so little about what lies below the sea surface. One new emerging technology that can help in oceans exploration is underwater wireless sensor network (UWSN). In such a network, a number of sensors are connected to a set of nodes that collect the data from them. Then, each node communicate its retrieved data to the other parts of the network through wireless links. So, an important step in the implementation of an UWSN is the design of an adequate transmitter/receiver system that is reliable, easy to implement, energy efficient and adapted to the underwater environment. Thanks to its cost-effectiveness and low-energy consumption property, optical underwater communication turns to be the most adequate solution for medium range node connections in an UWSN. To evaluate the optical underwater channel, we have studied its impulse response using a Monte Carlo simulator that takes into consideration all the transmitter, receiver and medium characteristics. We have demonstrated through these simulations that the channel delay dispersion is negligible in most practical cases. Therefore, we do not need to perform computationally complex signal processing such as channel equalization at the receiver. After studying the channel characteristics, we have turned our attention onto the transmitter/receiver system design. For this, we have simulated a system composed by a high-power monochromatic 532 nm LED transmitter and a Silicon PIN photodiode receiver with a collimating lens for capturing the scattered light. After photo-detection, the photo-current is converted to a voltage and low-pass filtered to limit the thermal noise variance which is the dominant noise in the receiver. Note that, in our case, background noise can be neglected because we are working in deep waters were the sunlight cannot penetrate. Then, using on-off-keying (OOK) modulation, we have proceeded to signal detection based on optimum

  19. Study of environmental noise in a BWR plant like the Nuclear Power Plant Laguna Verde; Estudio de ruido ambiental en una planta BWR como la Central Nuclear Laguna Verde

    Energy Technology Data Exchange (ETDEWEB)

    Tijerina S, F.; Cruz G, M.; Amador C, C., E-mail: francisco.tijerina@cfe.gob.mx [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verde, Subgerencia de Ingenieria, Carretera Cardel-Nautla Km. 42.5, Alto Lucero, Veracruz (Mexico)

    2013-10-15

    In all industry type the health costs generated by the noise are high, because the noise can cause nuisance and to harm the capacity to work when causing tension and to perturb the concentration, and in more severe cases to reach to lose the sense of the hearing in the long term. The noise levels in the industry have been designated for the different types of use like residential, commercial, and industrial and silence areas. The noise can cause accidents when obstructing the communications and alarm signs. For this reason the noise should be controlled and mitigated, at a low level as reasonably is possible, taking into account that the noise is an acoustic contamination. The present study determines a bases line of the environmental noise levels in a nuclear power plant BWR-5 as Laguna Verde, (like reference) to be able to determine and to give pursuit to the possible solutions to eliminate or to limit the noise level in the different job areas. The noise levels were registered with a meter of integrative noise level (sonometer) and areas of noise exposure levels mapping the general areas in the buildings were established, being the registered maximum level of 96.94 dba in the building of the Reactor-elevation 0.65 m under the operation conditions of Extended Power Up rate (EPU) of 120% PTN. Knowing that the exposition to noises and the noise dose in the job place can influence in the health and in the safety of the workers, are extensive topics that they should be analyzed for separate as they are: to) the effects in the health of the exposure to the noise, b) how measuring the noise, c) the methods and technologies to combat and to control the noise in the industry by part of engineering area and d) the function of the industrial safety bodies as delegates of the health and safety in the task against the noise in the job. (author)

  20. Underwater Coatings for Contamination Control

    International Nuclear Information System (INIS)

    Julia L. Tripp; Kip Archibald; Ann-Marie Phillips; Joseph Campbell

    2004-01-01

    The Idaho National Engineering and Environmental Laboratory (INEEL) is deactivating several fuel storage basins. Airborne contamination is a concern when the sides of the basins are exposed and allowed to dry during water removal. One way of controlling this airborne contamination is to fix the contamination in place while the pool walls are still submerged. There are many underwater coatings available on the market that are used in marine, naval and other applications. A series of tests were run to determine whether the candidate underwater fixatives are easily applied and adhere well to the substrates (pool wall materials) found in INEEL fuel pools. The four pools considered included (1) Test Area North (TAN-607) with epoxy painted concrete walls; (2) Idaho Nuclear Technology and Engineering Center (INTEC) (CPP-603) with bare concrete walls; (3) Materials Test Reactor (MTR) Canal with stainless steel lined concrete walls; and (4) Power Burst Facility (PBF-620) with stainless steel lined concrete walls on the bottom and epoxy painted carbon steel lined walls on the upper portions. Therefore, the four materials chosen for testing included bare concrete, epoxy painted concrete, epoxy painted carbon steel, and stainless steel. The typical water temperature of the pools varies from 55 F to 80 F dependent on the pool and the season. These tests were done at room temperature. The following criteria were used during this evaluation. The underwater coating must: (1) Be easy to apply; (2) Adhere well to the four surfaces of interest; (3) Not change or have a negative impact on water chemistry or clarity; (4) Not be hazardous in final applied form; and (5) Be proven in other underwater applications. In addition, it is desirable for the coating to have a high pigment or high cross-link density to prevent radiation from penetrating. This paper will detail the testing completed and the test results. A proprietary two-part, underwater epoxy owned by S. G. Pinney and Associates

  1. Aquatic Acoustic Metrics Interface Utility for Underwater Sound Monitoring and Analysis

    Science.gov (United States)

    Ren, Huiying; Halvorsen, Michele B.; Deng, Zhiqun Daniel; Carlson, Thomas J.

    2012-01-01

    Fishes and marine mammals may suffer a range of potential effects from exposure to intense underwater sound generated by anthropogenic activities such as pile driving, shipping, sonars, and underwater blasting. Several underwater sound recording (USR) devices have been built to acquire samples of the underwater sound generated by anthropogenic activities. Software becomes indispensable for processing and analyzing the audio files recorded by these USRs. In this paper, we provide a detailed description of a new software package, the Aquatic Acoustic Metrics Interface (AAMI), specifically designed for analysis of underwater sound recordings to provide data in metrics that facilitate evaluation of the potential impacts of the sound on aquatic animals. In addition to the basic functions, such as loading and editing audio files recorded by USRs and batch processing of sound files, the software utilizes recording system calibration data to compute important parameters in physical units. The software also facilitates comparison of the noise sound sample metrics with biological measures such as audiograms of the sensitivity of aquatic animals to the sound, integrating various components into a single analytical frame. The features of the AAMI software are discussed, and several case studies are presented to illustrate its functionality. PMID:22969353

  2. Aquatic Acoustic Metrics Interface Utility for Underwater Sound Monitoring and Analysis

    Directory of Open Access Journals (Sweden)

    Thomas J. Carlson

    2012-05-01

    Full Text Available Fishes and marine mammals may suffer a range of potential effects from exposure to intense underwater sound generated by anthropogenic activities such as pile driving, shipping, sonars, and underwater blasting. Several underwater sound recording (USR devices have been built to acquire samples of the underwater sound generated by anthropogenic activities. Software becomes indispensable for processing and analyzing the audio files recorded by these USRs. In this paper, we provide a detailed description of a new software package, the Aquatic Acoustic Metrics Interface (AAMI, specifically designed for analysis of underwater sound recordings to provide data in metrics that facilitate evaluation of the potential impacts of the sound on aquatic animals. In addition to the basic functions, such as loading and editing audio files recorded by USRs and batch processing of sound files, the software utilizes recording system calibration data to compute important parameters in physical units. The software also facilitates comparison of the noise sound sample metrics with biological measures such as audiograms of the sensitivity of aquatic animals to the sound, integrating various components into a single analytical frame. The features of the AAMI software are discussed, and several case studies are presented to illustrate its functionality.

  3. Periodismo ambiental

    Directory of Open Access Journals (Sweden)

    Lucía Lemos

    2015-01-01

    Full Text Available Los periodistas toman el tema del medio ambiente cada vez más en serio. El uso de temas relacionados con el medio ambiente, debe estar ligado al análisis socio-económico y a las posibilidades de comunicación y educación de diferentes regiones del mundo. A continuación se presenta un resumen de la situación ambiental, las acciones de prensa y comunicación que se llevan a cabo en América Central (Panamá, El Salvador, Costa Rica y en Sudamérica Brasil,Colombia, Chile, México, y Perú. Se concluye en la necesidad de formar hábitos ecológicos. Los comunicadores deben presentar soluciones a los problemas, fomentar campañas comunes, compartir información y velar por el ambiente ambiente para que las generaciones futuras no tengan que perecer.

  4. Underwater Animal Monitoring Magnetic Sensor System

    KAUST Repository

    Kaidarova, Altynay

    2017-10-01

    Obtaining new insights into the behavior of free-living marine organisms is fundamental for conservation efforts and anticipating the impact of climate change on marine ecosystems. Despite the recent advances in biotelemetry, collecting physiological and behavioral parameters of underwater free-living animals remains technically challenging. In this thesis, we develop the first magnetic underwater animal monitoring system that utilizes Tunnel magnetoresistance (TMR) sensors, the most sensitive solid-state sensors today, coupled with flexible magnetic composites. The TMR sensors are composed of CoFeB free layers and MgO tunnel barriers, patterned using standard optical lithography and ion milling procedures. The short and long-term stability of the TMR sensors has been studied using statistical and Allan deviation analysis. Instrumentation noise has been reduced using optimized electrical interconnection schemes. We also develop flexible NdFeB-PDMS composite magnets optimized for applications in corrosive marine environments, and which can be attached to marine animals. The magnetic and mechanical properties are studied for different NdFeB powder concentrations and the performance of the magnetic composites for different exposure times to sea water is systematically investigated. Without protective layer, the composite magnets loose more than 50% of their magnetization after 51 days in seawater. The durability of the composite magnets can be considerably improved by using polymer coatings which are protecting the composite magnet, whereby Parylene C is found to be the most effective solution, providing simultaneously corrosion resistance, flexibility, and enhanced biocompatibility. A Parylene C film of 2μm thickness provides the sufficient protection of the magnetic composite in corrosive aqueous environments for more than 70 days. For the high level performance of the system, the theoretically optimal position of the composite magnets with respect to the sensing

  5. Underwater noise from geotechnical drilling and standard penetration testing.

    Science.gov (United States)

    Erbe, Christine; McPherson, Craig

    2017-09-01

    Geotechnical site investigations prior to marine construction typically involve shallow, small-core drilling and standard penetration testing (SPT), during which a small tube is hammered into the ground at the bottom of the borehole. Drilling (120 kW, 83 mm diameter drillbit, 1500 rpm, 16-17 m drill depth in sand and mudstone) and SPT (50 mm diameter test tube, 15 mm wall thickness, 100 kg hammer, 1 m drop height) by a jack-up rig in 7-13 m of water were recorded with a drifting hydrophone at 10-50 m range. Source levels were 142-145 dB re 1 μPa rms @ 1 m (30-2000 Hz) for drilling and 151-160 dB re 1 μPa 2 s @ 1 m (20-24 000 Hz) for SPT.

  6. Further Studies of the Underwater Noise Produced by Rainfall

    Science.gov (United States)

    1989-08-17

    6. 0 0 The dat- anaiysis was done using the Cricket Graph software package available for Macintosh ,,,nputers. EXPLANATION OF DATA SET 1 The first...Milena and Felipe Gaitan, Steve Horsburgh (especially to you and Mike for curing the computers I unknowingly infected or injured). Joe Richardson...Stagnant Air." Journal of Meteorology. 6 243 (1949) Longuet-Higgins, Michael S. "An Analytic Model of Sound Production by Rain-drops." The Journal of the

  7. Beaked and Baleen Whale Hearing: Modeling Responses to Underwater Noise

    Science.gov (United States)

    2009-06-01

    Ketten, D. R. 1994. The role of temporal bone imaging in cochlear implants. Curr. Opn. Otol. & HN Surg., Otology -Neurotology. 2 (5): 401-408... Otology and Laryngology. 107 (11): 1-16. Ketten, D. R. and D. Wartzok. 1990. Three-dimensional reconstructions of the dolphin cochlea. In

  8. Characterization of an Outdoor Ambient Radio Frequency Environment

    Science.gov (United States)

    2016-02-16

    TYPE Final 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE Test Operations Procedure (TOP) 06-2-595 Characterization of an Outdoor Ambient ...DTIC), AD No.: 14. ABSTRACT This TOP provides procedures to characterize an ambient radio frequency (RF) environment (sometimes referred to as...spectrum analyzer, ambient RF noise floor, RF interference 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT SAR 18

  9. Noise Pollution

    Science.gov (United States)

    ... Us Share Clean Air Act Title IV - Noise Pollution The 1990 Clean Air Act Amendments added a ... abatement 7642 Authorization of appropriations What is Noise Pollution? The traditional definition of noise is “unwanted or ...

  10. An Adaptive UKF Based SLAM Method for Unmanned Underwater Vehicle

    Directory of Open Access Journals (Sweden)

    Hongjian Wang

    2013-01-01

    Full Text Available This work proposes an improved unscented Kalman filter (UKF-based simultaneous localization and mapping (SLAM algorithm based on an adaptive unscented Kalman filter (AUKF with a noise statistic estimator. The algorithm solves the issue that conventional UKF-SLAM algorithms have declining accuracy, with divergence occurring when the prior noise statistic is unknown and time-varying. The new SLAM algorithm performs an online estimation of the statistical parameters of unknown system noise by introducing a modified Sage-Husa noise statistic estimator. The algorithm also judges whether the filter is divergent and restrains potential filtering divergence using a covariance matching method. This approach reduces state estimation error, effectively improving navigation accuracy of the SLAM system. A line feature extraction is implemented through a Hough transform based on the ranging sonar model. Test results based on unmanned underwater vehicle (UUV sea trial data indicate that the proposed AUKF-SLAM algorithm is valid and feasible and provides better accuracy than the standard UKF-SLAM system.

  11. Underwater sound scattering and absorption by a coated infinite plate with a distributed inhomogeneity.

    Science.gov (United States)

    Zhang, Yanni; Pan, Jie

    2013-04-01

    This paper concerns itself with the scattering and absorption of underwater incident sound by a coated infinite plate with an attached distributed inhomogeneity. Its objective is to determine if the distributed inhomogeneity can provide additional local reflection, such that it only increases the signal-to-noise ratio for a hydrophone detector placed on the inhomogeneity without significantly decreasing the overall sound absorption of the coated plate.

  12. Model based image restoration for underwater images

    Science.gov (United States)

    Stephan, Thomas; Frühberger, Peter; Werling, Stefan; Heizmann, Michael

    2013-04-01

    The inspection of offshore parks, dam walls and other infrastructure under water is expensive and time consuming, because such constructions must be inspected manually by divers. Underwater buildings have to be examined visually to find small cracks, spallings or other deficiencies. Automation of underwater inspection depends on established water-proved imaging systems. Most underwater imaging systems are based on acoustic sensors (sonar). The disadvantage of such an acoustic system is the loss of the complete visual impression. All information embedded in texture and surface reflectance gets lost. Therefore acoustic sensors are mostly insufficient for these kind of visual inspection tasks. Imaging systems based on optical sensors feature an enormous potential for underwater applications. The bandwidth from visual imaging systems reach from inspection of underwater buildings via marine biological applications through to exploration of the seafloor. The reason for the lack of established optical systems for underwater inspection tasks lies in technical difficulties of underwater image acquisition and processing. Lightening, highly degraded images make a computational postprocessing absolutely essential.

  13. Imagery-derived modulation transfer function and its applications for underwater imaging

    Science.gov (United States)

    Hou, Weilin; Weidemann, Alan D.; Gray, Deric J.; Fournier, Georges R.

    2007-09-01

    The main challenge working with underwater imagery results from both rapid decay of signals due to absorption, which leads to poor signal to noise returns, and the blurring caused by strong scattering by the water itself and constituents within, especially particulates. The modulation transfer function (MTF) of an optical system gives the detailed and precise information regarding the system behavior. Underwater imageries can be better restored with the knowledge of the system MTF or the point spread function (PSF), the Fourier transformed equivalent, extending the performance range as well as the information retrieval from underwater electro-optical system. This is critical in many civilian and military applications, including target and especially mine detection, search and rescue, and diver visibility. This effort utilizes test imageries obtained by the Laser Underwater Camera Imaging Enhancer (LUCIE) from Defense Research and Development Canada (DRDC), during an April-May 2006 trial experiment in Panama City, Florida. Imaging of a standard resolution chart with various spatial frequencies were taken underwater in a controlled optical environment, at varying distances. In-water optical properties during the experiment were measured, which included the absorption and attenuation coefficients, particle size distribution, and volume scattering function. Resulting images were preprocessed to enhance signal to noise ratio by averaging multiple frames, and to remove uneven illumination at target plane. The MTF of the medium was then derived from measurement of above imageries, subtracting the effect of the camera system. PSFs converted from the measured MTF were then used to restore the blurred imageries by different deconvolution methods. The effects of polarization from source to receiver on resulting MTFs were examined and we demonstrate that matching polarizations do enhance system transfer functions. This approach also shows promise in deriving medium optical

  14. Combustion noise

    Science.gov (United States)

    Strahle, W. C.

    1977-01-01

    A review of the subject of combustion generated noise is presented. Combustion noise is an important noise source in industrial furnaces and process heaters, turbopropulsion and gas turbine systems, flaring operations, Diesel engines, and rocket engines. The state-of-the-art in combustion noise importance, understanding, prediction and scaling is presented for these systems. The fundamentals and available theories of combustion noise are given. Controversies in the field are discussed and recommendations for future research are made.

  15. A new technique for robot vision in autonomous underwater vehicles using the color shift in underwater imaging

    Science.gov (United States)

    2017-06-01

    FOR ROBOT VISION IN AUTONOMOUS UNDERWATER VEHICLES USING THE COLOR SHIFT IN UNDERWATER IMAGING by Jake A. Jones June 2017 Thesis Advisor... VEHICLES USING THE COLOR SHIFT IN UNDERWATER IMAGING 5. FUNDING NUMBERS 6. AUTHOR(S) Jake A. Jones 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS...underwater vehicles (AUVs), robot vision, autonomy, visual odometry, underwater color shift, optical properties of water 15. NUMBER OF PAGES 75 16

  16. Spectral analysis of underwater explosions in the Dead Sea

    Science.gov (United States)

    Gitterman, Y.; Ben-Avraham, Z.; Ginzburg, A.

    1998-08-01

    The present study utilizes the Israel Seismic Network (ISN) as a spatially distributed multichannel system for the discrimination of low-magnitude events (ML UWEs) and 16 earthquakes in the magnitude range ML = 1.6-2.8, within distances of 10-150 km, recorded by the ISN, were selected for the analysis. The analysis is based on a smoothed (0.5 Hz window) Fourier spectrum of the whole signal (defined by the signal-to-noise criterion), without picking separate wave phases. It was found that the classical discriminant of the seismic energy ratio between the relatively low-frequency (1-6 Hz) and high-frequency (6-11 Hz) bands, averaged over an ISN subnetwork, showed an overlap between UWEs and earthquakes and cannot itself provide reliable identification. We developed and tested a new multistation discriminant based on the low- frequency spectral modulation (LFSM) method. In our case the LFSM is associated with the bubbling effect in underwater explosions. The method demonstrates a distinct azimuth-invariant coherency of spectral shapes in the low-frequency range (1-12 Hz) of short-period seismometer systems. The coherency of the modulated spectra for different ISN stations was measured by semblance statistics commonly used in seismic prospecting for phase correlation in the time domain. The modified statistics provided an almost complete separation between earthquakes and underwater explosions.

  17. Robust adaptive control of underwater vehicles: A comparative study

    Directory of Open Access Journals (Sweden)

    Thor I. Fossen

    1996-01-01

    Full Text Available Robust adaptive control of underwater vehicles in 6 DOF is analysed in the context of measurement noise. The performance of the adaptive control laws of Sadegh and Harowitz (1990 and Slotine and Benedetto (1990 are compared. Both these schemes require that all states are measured, that is the velocities and positions in surge, sway, heave, roll, pitch and yaw. However, for underwater vehicles it is difficult to measure the linear velocities whereas angular velocity measurements can be obtained by using a 3 axes angular rate sensor. This problem is addressed by designing a nonlinear observer for linear velocity state estimation. The proposed observer requires that the position and the attitude are measured, e.g. by using a hydroacoustic positioning system for linear positions, two gyros for roll and pitch and a compass for yaw. In addition angular rate measurements will be assumed available from a 3-axes rate sensor or a state estimator. It is also assumed that the measurement rate is limited to 2 Hz for all the sensors. Simulation studies with a 3 DOF AUV model are used to demonstrate the convergence and robustness of the adaptive control laws and the velocity state observer.

  18. Polar Grid Navigation Algorithm for Unmanned Underwater Vehicles.

    Science.gov (United States)

    Yan, Zheping; Wang, Lu; Zhang, Wei; Zhou, Jiajia; Wang, Man

    2017-07-09

    To solve the unavailability of a traditional strapdown inertial navigation system (SINS) for unmanned underwater vehicles (UUVs) in the polar region, a polar grid navigation algorithm for UUVs is proposed in this paper. Precise navigation is the basis for UUVs to complete missions. The rapid convergence of Earth meridians and the serious polar environment make it difficult to establish the true heading of the UUV at a particular instant. Traditional SINS and traditional representation of position are not suitable in the polar region. Due to the restrictions of the complex underwater conditions in the polar region, a SINS based on the grid frame with the assistance of the OCTANS and the Doppler velocity log (DVL) is chosen for a UUV navigating in the polar region. Data fusion of the integrated navigation system is realized by a modified fuzzy adaptive Kalman filter (MFAKF). By neglecting the negative terms, and using T-S fuzzy logic in the adaptive regulation of the noise covariance, the proposed filter algorithm can improve navigation accuracy. Simulation and experimental results demonstrate that the polar grid navigation algorithm can effectively navigate a UUV sailing in the polar region.

  19. Jellyfish inspired underwater unmanned vehicle

    Science.gov (United States)

    Villanueva, Alex; Bresser, Scott; Chung, Sanghun; Tadesse, Yonas; Priya, Shashank

    2009-03-01

    An unmanned underwater vehicle (UUV) was designed inspired by the form and functionality of a Jellyfish. These natural organisms were chosen as bio-inspiration for a multitude of reasons including: efficiency of locomotion, lack of natural predators, proper form and shape to incorporate payload, and varying range of sizes. The structure consists of a hub body surrounded by bell segments and microcontroller based drive system. The locomotion of UUV was achieved by shape memory alloy "Biometal Fiber" actuation which possesses large strain and blocking force with adequate response time. The main criterion in design of UUV was the use of low-profile shape memory alloy actuators which act as artificial muscles. In this manuscript, we discuss the design of two Jellyfish prototypes and present experimental results illustrating the performance and power consumption.

  20. Underwater sympathetic detonation of pellet explosive

    Science.gov (United States)

    Kubota, Shiro; Saburi, Tei; Nagayama, Kunihito

    2017-06-01

    The underwater sympathetic detonation of pellet explosives was taken by high-speed photography. The diameter and the thickness of the pellet were 20 and 10 mm, respectively. The experimental system consists of the precise electric detonator, two grams of composition C4 booster and three pellets, and these were set in water tank. High-speed video camera, HPV-X made by Shimadzu was used with 10 Mfs. The underwater explosions of the precise electric detonator, the C4 booster and a pellet were also taken by high-speed photography to estimate the propagation processes of the underwater shock waves. Numerical simulation of the underwater sympathetic detonation of the pellet explosives was also carried out and compared with experiment.

  1. Underwater Grass Comeback Helps Chesapeake Bay

    Science.gov (United States)

    The fortified Susquehanna Flats, the largest bed of underwater grasses in the Chesapeake Bay, seems able to withstand a major weather punch. Its resilience is contributing to an overall increase in the Bay’s submerged aquatic vegetation.

  2. Sensor network architectures for monitoring underwater pipelines.

    Science.gov (United States)

    Mohamed, Nader; Jawhar, Imad; Al-Jaroodi, Jameela; Zhang, Liren

    2011-01-01

    This paper develops and compares different sensor network architecture designs that can be used for monitoring underwater pipeline infrastructures. These architectures are underwater wired sensor networks, underwater acoustic wireless sensor networks, RF (radio frequency) wireless sensor networks, integrated wired/acoustic wireless sensor networks, and integrated wired/RF wireless sensor networks. The paper also discusses the reliability challenges and enhancement approaches for these network architectures. The reliability evaluation, characteristics, advantages, and disadvantages among these architectures are discussed and compared. Three reliability factors are used for the discussion and comparison: the network connectivity, the continuity of power supply for the network, and the physical network security. In addition, the paper also develops and evaluates a hierarchical sensor network framework for underwater pipeline monitoring.

  3. Tracking the position of the underwater robot for nuclear reactor inspection

    International Nuclear Information System (INIS)

    Jeo, J. W.; Kim, C. H.; Seo, Y. C.; Choi, Y. S.; Kim, S. H.

    2003-01-01

    The tracking procedure of the underwater mobile robot moving and submerging ahead to nuclear reactor vessel for visual inspection, which is required to find the foreign objects such as loose parts, is described. The yellowish underwater robot body tends to present a big contrast to boron solute cold water of nuclear reactor vessel, tinged with indigo by the Cerenkov effect. In this paper, we have found and tracked the positions of underwater mobile robot using the two color information, yellow and indigo. From the horizontal and vertical profiles analysis of the color image, the blue, green, and the gray component have the inferior signal-to-noise characteristics compared to the red component. The center coordinates extraction procedures areas follows. The first step is to segment the underwater robot body to cold water with indigo background. From the RGB color components of the entire monitoring image taken with the color CCD camera, we have selected the red color component. In the selected red image, we extracted the positions of the underwater mobile robot using the following process sequences; binarization, labelling, and centroid extraction techniques. In the experiment carried out at the Youngkwang unit 5 nuclear reactor vessel, we have tracked the center positions of the underwater robot submerged near the cold leg and the hot leg way, which is fathomed to 10m deep in depth. When the position of the robot vehicle fluctuates between the previous and the current image frame due to the flickering noise and light source, installed temporally in the bottom of the reactor vessel, we adaptively adjusted the ROI window. Adding the ROI windows of the previous frame to the current frame, and then setting up the ROI window of the next image frame, we can robustly track the positions of the underwater robot and control the target position's divergence. From these facts, we can conclude that using the red component from color camera is more efficient tracking method

  4. Underwater optical wireless communications: depth dependent variations in attenuation.

    Science.gov (United States)

    Johnson, Laura J; Green, Roger J; Leeson, Mark S

    2013-11-20

    Depth variations in the attenuation coefficient for light in the ocean were calculated using a one-parameter model based on the chlorophyll-a concentration C(c) and experimentally-determined Gaussian chlorophyll-depth profiles. The depth profiles were related to surface chlorophyll levels for the range 0-4  mg/m², representing clear, open ocean. The depth where C(c) became negligible was calculated to be shallower for places of high surface chlorophyll; 111.5 m for surface chlorophyll 0.8communication links, calculated to be 0.0092  m⁻¹ at a wavelength of 430 nm. By combining this with satellite surface-chlorophyll data, it is possible to quantify the attenuation between any two locations in the ocean, with applications for low-noise or secure underwater communications and vertical links from the ocean surface.

  5. Energy-Efficient Channel Coding Strategy for Underwater Acoustic Networks

    Directory of Open Access Journals (Sweden)

    Grasielli Barreto

    2017-03-01

    Full Text Available Underwater acoustic networks (UAN allow for efficiently exploiting and monitoring the sub-aquatic environment. These networks are characterized by long propagation delays, error-prone channels and half-duplex communication. In this paper, we address the problem of energy-efficient communication through the use of optimized channel coding parameters. We consider a two-layer encoding scheme employing forward error correction (FEC codes and fountain codes (FC for UAN scenarios without feedback channels. We model and evaluate the energy consumption of different channel coding schemes for a K-distributed multipath channel. The parameters of the FEC encoding layer are optimized by selecting the optimal error correction capability and the code block size. The results show the best parameter choice as a function of the link distance and received signal-to-noise ratio.

  6. Underwater photogrammetry successful in Spain and France

    International Nuclear Information System (INIS)

    Anon.

    1988-01-01

    Underwater photogrammetry has been used to measure distortions in fuel assembly alignment pins in the upper internals of the Almarez and Dampierre PWRs. Photogrammetry is a three-dimensional precision measurement method using photographic techniques for the on-site measurement phase. On the strength of the operations at the two PWRs, underwater photogrammetry is now considered as a practical and effective technique for dimensional inspection at nuclear plants. (U.K.)

  7. Underwater gait analysis in Parkinson's disease.

    Science.gov (United States)

    Volpe, Daniele; Pavan, Davide; Morris, Meg; Guiotto, Annamaria; Iansek, Robert; Fortuna, Sofia; Frazzitta, Giuseppe; Sawacha, Zimi

    2017-02-01

    Although hydrotherapy is one of the physical therapies adopted to optimize gait rehabilitation in people with Parkinson disease, the quantitative measurement of gait-related outcomes has not been provided yet. This work aims to document the gait improvements in a group of parkinsonians after a hydrotherapy program through 2D and 3D underwater and on land gait analysis. Thirty-four parkinsonians and twenty-two controls were enrolled, divided into two different cohorts. In the first one, 2 groups of patients underwent underwater or land based walking training; controls underwent underwater walking training. Hence pre-treatment 2D underwater and on land gait analysis were performed, together with post-treatment on land gait analysis. Considering that current literature documented a reduced movement amplitude in parkinsonians across all lower limb joints in all movement planes, 3D underwater and on land gait analysis were performed on a second cohort of subjects (10 parkinsonians and 10 controls) who underwent underwater gait training. Baseline land 2D and 3D gait analysis in parkinsonians showed shorter stride length and slower speed than controls, in agreement with previous findings. Comparison between underwater and on land gait analysis showed reduction in stride length, cadence and speed on both parkinsonians and controls. Although patients who underwent underwater treatment exhibited significant changes on spatiotemporal parameters and sagittal plane lower limb kinematics, 3D gait analysis documented a significant (p<0.05) improvement in all movement planes. These data deserve attention for research directions promoting the optimal recovery and maintenance of walking ability. Crown Copyright © 2016. Published by Elsevier B.V. All rights reserved.

  8. Dolphin Sounds-Inspired Covert Underwater Acoustic Communication and Micro-Modem

    Science.gov (United States)

    Qiao, Gang; Liu, Songzuo; Bilal, Muhammad

    2017-01-01

    A novel portable underwater acoustic modem is proposed in this paper for covert communication between divers or underwater unmanned vehicles (UUVs) and divers at a short distance. For the first time, real dolphin calls are used in the modem to realize biologically inspired Covert Underwater Acoustic Communication (CUAC). A variety of dolphin whistles and clicks stored in an SD card inside the modem helps to realize different biomimetic CUAC algorithms based on the specified covert scenario. In this paper, the information is conveyed during the time interval between dolphin clicks. TMS320C6748 and TLV320AIC3106 are the core processors used in our unique modem for fast digital processing and interconnection with other terminals or sensors. Simulation results show that the bit error rate (BER) of the CUAC algorithm is less than 10−5 when the signal to noise ratio is over ‒5 dB. The modem was tested in an underwater pool, and a data rate of 27.1 bits per second at a distance of 10 m was achieved. PMID:29068363

  9. Dolphin Sounds-Inspired Covert Underwater Acoustic Communication and Micro-Modem

    Directory of Open Access Journals (Sweden)

    Gang Qiao

    2017-10-01

    Full Text Available A novel portable underwater acoustic modem is proposed in this paper for covert communication between divers or underwater unmanned vehicles (UUVs and divers at a short distance. For the first time, real dolphin calls are used in the modem to realize biologically inspired Covert Underwater Acoustic Communication (CUAC. A variety of dolphin whistles and clicks stored in an SD card inside the modem helps to realize different biomimetic CUAC algorithms based on the specified covert scenario. In this paper, the information is conveyed during the time interval between dolphin clicks. TMS320C6748 and TLV320AIC3106 are the core processors used in our unique modem for fast digital processing and interconnection with other terminals or sensors. Simulation results show that the bit error rate (BER of the CUAC algorithm is less than 10 − 5 when the signal to noise ratio is over ‒5 dB. The modem was tested in an underwater pool, and a data rate of 27.1 bits per second at a distance of 10 m was achieved.

  10. Dolphin Sounds-Inspired Covert Underwater Acoustic Communication and Micro-Modem.

    Science.gov (United States)

    Qiao, Gang; Zhao, Yunjiang; Liu, Songzuo; Bilal, Muhammad

    2017-10-25

    A novel portable underwater acoustic modem is proposed in this paper for covert communication between divers or underwater unmanned vehicles (UUVs) and divers at a short distance. For the first time, real dolphin calls are used in the modem to realize biologically inspired Covert Underwater Acoustic Communication (CUAC). A variety of dolphin whistles and clicks stored in an SD card inside the modem helps to realize different biomimetic CUAC algorithms based on the specified covert scenario. In this paper, the information is conveyed during the time interval between dolphin clicks. TMS320C6748 and TLV320AIC3106 are the core processors used in our unique modem for fast digital processing and interconnection with other terminals or sensors. Simulation results show that the bit error rate (BER) of the CUAC algorithm is less than 10 - 5 when the signal to noise ratio is over ‒5 dB. The modem was tested in an underwater pool, and a data rate of 27.1 bits per second at a distance of 10 m was achieved.

  11. Underwater 3D Reconstruction Based on Geometric Transformation of Sonar and Depth Information

    Science.gov (United States)

    Dong, Mingjie; Chou, Wusheng; Yao, Guodong

    2017-10-01

    3D reconstruction is of vital importance to detect and monitor the underwater environment. A method based on geometric transformation of mechanical scanning sonar and depth information is proposed, in which the point cloud data from sonar and depth gauge are acquired to reconstruct the underwater 3D environment. However, noise and interference can affect the measurement of sonar, and movement of sonar during measurement can lead to distortion of the received data. Meanwhile, translation and rotation movement of sonar head may happen when ROV dives which can lead to different body reference coordinates of different scanning. To solve this, pre-processing and motion compensation are implemented at first, and underwater matching correction algorithm is used to calculate the translation and rotation of the sonar head. Then the inverse operation is implemented to convert the scan data of every depth into the same coordinate reference system. Finally, surface reconstruction of point clouds from sonar the depth information are used to reconstruct underwater environment based on MLS (Moving Least Square Method) using PCL (Point Cloud Library). Water tank experiments verify the effectiveness of the proposed method.

  12. The influence of environmental parameters on the optimal frequency in a shallow underwater acoustic channel

    Science.gov (United States)

    Zarnescu, George

    2015-02-01

    In a shallow underwater acoustic channel the delayed replicas of a transmitted signal are mainly due to the interactions with the sea surface and the bottom layer. If a specific underwater region on the globe is considered, for which the sedimentary layer structure is constant across the transmission distance, then the variability of the amplitude-delay profile is determined by daily and seasonal changes of the sound speed profile (SSP) and by weather changes, such as variations of the wind speed. Such a parameter will influence the attenuation at the surface, the noise level and the profile of the sea surface. The temporal variation of the impulse response in a shallow underwater acoustic channel determines the variability of the optimal transmission frequency. If the ways in which the optimal frequency changes can be predicted, then an adaptive analog transceiver can be easily designed for an underwater acoustic modem or it can be found when a communication link has high throughput. In this article it will be highlighted the way in which the amplitude-delay profile is affected by the sound speed profile, wind speed and channel depth and also will be emphasized the changes of the optimal transmission frequency in a configuration, where the transmitter and receiver are placed on the seafloor and the bathymetry profile will be considered flat, having a given composition.

  13. Affordable underwater wireless optical communication using LEDs

    Science.gov (United States)

    Pilipenko, Vladimir; Arnon, Shlomi

    2013-09-01

    In recent years the need for high data rate underwater wireless communication (WC) has increased. Nowadays, the conventional technology for underwater communication is acoustic. However, the maximum data rate that acoustic technology can provide is a few kilobits per second. On the other hand, emerging applications such as underwater imaging, networks of sensors and swarms of underwater vehicles require much faster data rates. As a result, underwater optical WC, which can provide much higher data rates, has been proposed as an alternative means of communication. In addition to high data rates, affordable communication systems become an important feature in the development requirements. The outcome of these requirements is a new system design based on off-the-shelf components such as blue and green light emitting diodes (LEDs). This is due to the fact that LEDs offer solutions characterized by low cost, high efficiency, reliability and compactness. However, there are some challenges to be met when incorporating LEDs as part of the optical transmitter, such as low modulation rates and non linearity. In this paper, we review the main challenges facing the incorporation of LEDs as an integral part of underwater WC systems and propose some techniques to mitigate the LED limitations in order to achieve high data rate communication

  14. An underwater optical wireless communication network

    Science.gov (United States)

    Arnon, Shlomi

    2009-08-01

    The growing need for underwater observation and sub-sea monitoring systems has stimulated considerable interest in advancing the enabling technologies of underwater wireless communication and underwater sensor networks. This communication technology is expected to play an important role in investigating climate change, in monitoring biological, bio-geochemical, evolutionary and ecological changes in the sea, ocean and lake environments and in helping to control and maintain oil production facilities and harbors using unmanned underwater vehicles (UUVs), submarines, ships, buoys, and divers. However, the present technology of underwater acoustic communication cannot provide the high data rate required to investigate and monitor these environments and facilities. Optical wireless communication has been proposed as the best alternative to meet this challenge. We present models of three kinds of optical wireless communication links a) a line-of-sight link, b) a modulating retro-reflector link and c) a reflective link, all of which can provide the required data rate. We analyze the link performance based on these models. From the analysis, it is clear that as the water absorption increases, the communication performance decreases dramatically for the three link types. However, by using the scattered lighted it was possible to mitigate this decrease in some cases. We conclude from the analysis that a high data rate underwater optical wireless network is a feasible solution for emerging applications such as UUV to UUV links and networks of sensors, and extended ranges in these applications could be achieved by applying a multi-hop concept.

  15. CNOSSOS-EU: Development of a common environmental noise assessment method in the European Union; CNOSSOS-EU: desarrollo de un metodo comun de evaluacion del ruido ambiental en la Union Europea

    Energy Technology Data Exchange (ETDEWEB)

    Aspuru Soloaga, I.; Segues Echazarreta Segues, F.

    2011-07-01

    This article presents the main aspects of the work undertaken in the development of the common european method of environmental noise assessment CNOSSOS-EU. It summarizes the design, structure and content, and the methodological basis on which it is based. Taking into account the experience gained in the first round of strategic noise mapping, some conclusions are settled about its applications for the third round, and tits implications for the Spanish case. (Author) 9 refs.

  16. THE ACOUSTIC CONTAMINATION OF SCHOOL ENVIRONMENT DUE TO URBAN NOISES IN THE FEDERAL DISTRICT, BRASIL = A CONTAMINAÇÃO ACÚSTICA DE AMBIENTES ESCOLARES DEVIDO AOS RUÍDOS URBANOS NO DISTRITO FEDERAL, BRASIL

    OpenAIRE

    Alexandre Eniz; Sérgio Luiz Garavelli

    2006-01-01

    Urban noises are more and more presents in our daily life, invading residences, work places, leisure locations, hospitals and schools, becoming a potential harm to social interaction, communication, behavior, school performance, health etc. The main objective of this work was to analyze and quantify the environmental noise in ten schools of the basic education in District Federal, Brazil. The adopted parameter was the equivalent sound pressure level Leq (A), which was evaluated according to t...

  17. Design and Analysis of Underwater Acoustic Networks with Reflected Links

    Science.gov (United States)

    Emokpae, Lloyd

    Underwater acoustic networks (UWANs) have applications in environmental state monitoring, oceanic profile measurements, leak detection in oil fields, distributed surveillance, and navigation. For these applications, sets of nodes are employed to collaboratively monitor an area of interest and track certain events or phenomena. In addition, it is common to find autonomous underwater vehicles (AUVs) acting as mobile sensor nodes that perform search-and-rescue missions, reconnaissance in combat zones, and coastal patrol. These AUVs are to work cooperatively to achieve a desired goal and thus need to be able to, in an ad-hoc manner, establish and sustain communication links in order to ensure some desired level of quality of service. Therefore, each node is required to adapt to environmental changes and be able to overcome broken communication links caused by external noise affecting the communication channel due to node mobility. In addition, since radio waves are quickly absorbed in the water medium, it is common for most underwater applications to rely on acoustic (or sound) rather than radio channels for mid-to-long range communications. However, acoustic channels pose multiple challenging issues, most notably the high transmission delay due to slow signal propagation and the limited channel bandwidth due to high frequency attenuation. Moreover, the inhomogeneous property of the water medium affects the sound speed profile while the signal surface and bottom reflections leads to multipath effects. In this dissertation, we address these networking challenges by developing protocols that take into consideration the underwater physical layer dynamics. We begin by introducing a novel surface-based reflection scheme (SBR), which takes advantage of the multipath effects of the acoustic channel. SBR works by using reflections from the water surface, and bottom, to establish non-line-of-sight (NLOS) communication links. SBR makes it possible to incorporate both line

  18. Near-field and high-resolution cylindrical noise source location method based on vector sound pressure array

    Directory of Open Access Journals (Sweden)

    ZUO Xiang

    2017-08-01

    Full Text Available The existing underwater noise source near-field location method usually assumes that the measurement plane is flat, which increases the difficulty of applying the underwater noise target test for cylindrical distribution. Simultaneously, the conventional near-field focused beam has a lower spatial resolution when used to locate an underwater noise source with cylindrical distribution. Moreover, the near-field underwater noise source location method based on the sound pressure array has a left and right side fuzzy problem. In order to solve these problems, by establishing the near-field measurement model of the noise source with cylindrical distribution as the measurement surface, and combining the unilateral directivity of the vector hydrophone and the high resolution characteristics of the MUSIC algorithm, a near-field and high resolution location method is proposed for cylindrical distribution based on vector sound pressure, and a computer simulation is carried out. The results show that the method can use a smaller array aperture to locate the underwater noise source, enabling it to be used to locate and recognize the noise sources of complex and large-scale cylindrical systems.

  19. A swarm of autonomous miniature underwater robot drifters for exploring submesoscale ocean dynamics

    Science.gov (United States)

    Jaffe, Jules S.; Franks, Peter J. S.; Roberts, Paul L. D.; Mirza, Diba; Schurgers, Curt; Kastner, Ryan; Boch, Adrien

    2017-01-01

    Measuring the ever-changing 3-dimensional (3D) motions of the ocean requires simultaneous sampling at multiple locations. In particular, sampling the complex, nonlinear dynamics associated with submesoscales (swarm of 16 independent vehicles whose 3D trajectories are measured near-continuously, underwater. As the vehicles drift with the ambient flow or execute preprogrammed vertical behaviours, the simultaneous measurements at multiple, known locations resolve the details of the flow within the swarm. We describe the design, construction, control and underwater navigation of the M-AUE. A field programme in the coastal ocean using a swarm of these robots programmed with a depth-holding behaviour provides a unique test of a physical-biological interaction leading to plankton patch formation in internal waves. The performance of the M-AUE vehicles illustrates their novel capability for measuring submesoscale dynamics.

  20. A swarm of autonomous miniature underwater robot drifters for exploring submesoscale ocean dynamics.

    Science.gov (United States)

    Jaffe, Jules S; Franks, Peter J S; Roberts, Paul L D; Mirza, Diba; Schurgers, Curt; Kastner, Ryan; Boch, Adrien

    2017-01-24

    Measuring the ever-changing 3-dimensional (3D) motions of the ocean requires simultaneous sampling at multiple locations. In particular, sampling the complex, nonlinear dynamics associated with submesoscales (swarm of 16 independent vehicles whose 3D trajectories are measured near-continuously, underwater. As the vehicles drift with the ambient flow or execute preprogrammed vertical behaviours, the simultaneous measurements at multiple, known locations resolve the details of the flow within the swarm. We describe the design, construction, control and underwater navigation of the M-AUE. A field programme in the coastal ocean using a swarm of these robots programmed with a depth-holding behaviour provides a unique test of a physical-biological interaction leading to plankton patch formation in internal waves. The performance of the M-AUE vehicles illustrates their novel capability for measuring submesoscale dynamics.

  1. Underwater image quality enhancement through Rayleigh-stretching and averaging image planes

    Directory of Open Access Journals (Sweden)

    Ahmad Shahrizan Abdul Ghani

    2014-12-01

    Full Text Available Visibility in underwater images is usually poor because of the attenuation of light in the water that causes low contrast and color variation. In this paper, a new approach for underwater image quality improvement is presented. The proposed method aims to improve underwater image contrast, increase image details, and reduce noise by applying a new method of using contrast stretching to produce two different images with different contrasts. The proposed method integrates the modification of the image histogram in two main color models, RGB and HSV The histograms of the color channel in the RGB color model are modified and remapped to follow the Rayleigh distribution within certain ranges. The image is then converted to the HSV color model, and the S and V components are modified within a certain limit. Qualitative and quantitative analyses indicate that the proposed method outperforms other state-of-the-art methods in terms of contrast, details, and noise reduction. The image color also shows much improvement.

  2. Underwater image quality enhancement through Rayleigh-stretching and averaging image planes

    Directory of Open Access Journals (Sweden)

    Ghani Ahmad Shahrizan Abdul

    2014-12-01

    Full Text Available Visibility in underwater images is usually poor because of the attenuation of light in the water that causes low contrast and color variation. In this paper, a new approach for underwater image quality improvement is presented. The proposed method aims to improve underwater image contrast, increase image details, and reduce noise by applying a new method of using contrast stretching to produce two different images with different contrasts. The proposed method integrates the modification of the image histogram in two main color models, RGB and HSV. The histograms of the color channel in the RGB color model are modified and remapped to follow the Rayleigh distribution within certain ranges. The image is then converted to the HSV color model, and the S and V components are modified within a certain limit. Qualitative and quantitative analyses indicate that the proposed method outperforms other state-of- the-art methods in terms of contrast, details, and noise reduction. The image color also shows much improvement.

  3. Attenuation of low-frequency underwater sound using an array of air-filled balloons and comparison to effective medium theory.

    Science.gov (United States)

    Lee, Kevin M; Wilson, Preston S; Wochner, Mark S

    2017-12-01

    The ultimate goal of this work is to accurately predict the attenuation through a collection of large (on the order of 10-cm-radius) tethered encapsulated bubbles used in underwater noise abatement systems. Measurements of underwater sound attenuation were performed during a set of lake experiments, where a low-frequency compact electromechanical sound source was surrounded by different arrays of encapsulated bubbles with various individual bubbles sizes and void fractions. The measurements were compared with an existing predictive model [Church, J. Acoust. Soc. Am. 97, 1510-1521 (1995)] of the dispersion relation for linear propagation in liquid containing encapsulated bubbles. Although the model was originally intended to describe ultrasound contrast agents, it is evaluated here for large bubbles, and hence low frequencies, as a design tool for future underwater noise abatement systems, and there is good quantitative agreement between the observations and the model.

  4. Minimizing noise-temperature measurement errors

    Science.gov (United States)

    Stelzried, C. T.

    1992-01-01

    An analysis of noise-temperature measurement errors of low-noise amplifiers was performed. Results of this analysis can be used to optimize measurement schemes for minimum errors. For the cases evaluated, the effective noise temperature (Te) of a Ka-band maser can be measured most accurately by switching between an ambient and a 2-K cooled load without an isolation attenuator. A measurement accuracy of 0.3 K was obtained for this example.

  5. Underwater Sensor Networks: A New Energy Efficient and Robust Architecture

    NARCIS (Netherlands)

    Climent, Salvador; Capella, Juan Vincente; Meratnia, Nirvana; Serrano, Juan José

    2012-01-01

    The specific characteristics of underwater environments introduce new challenges for networking protocols. In this paper, a specialized architecture for underwater sensor networks (UWSNs) is proposed and evaluated. Experiments are conducted in order to analyze the suitability of this protocol for

  6. High level white noise generator

    International Nuclear Information System (INIS)

    Borkowski, C.J.; Blalock, T.V.

    1979-01-01

    A wide band, stable, random noise source with a high and well-defined output power spectral density is provided which may be used for accurate calibration of Johnson Noise Power Thermometers (JNPT) and other applications requiring a stable, wide band, well-defined noise power spectral density. The noise source is based on the fact that the open-circuit thermal noise voltage of a feedback resistor, connecting the output to the input of a special inverting amplifier, is available at the amplifier output from an equivalent low output impedance caused by the feedback mechanism. The noise power spectral density level at the noise source output is equivalent to the density of the open-circuit thermal noise or a 100 ohm resistor at a temperature of approximately 64,000 Kelvins. The noise source has an output power spectral density that is flat to within 0.1% (0.0043 db) in the frequency range of from 1 KHz to 100 KHz which brackets typical passbands of the signal-processing channels of JNPT's. Two embodiments, one of higher accuracy that is suitable for use as a standards instrument and another that is particularly adapted for ambient temperature operation, are illustrated in this application

  7. High level white noise generator

    Science.gov (United States)

    Borkowski, Casimer J.; Blalock, Theron V.

    1979-01-01

    A wide band, stable, random noise source with a high and well-defined output power spectral density is provided which may be used for accurate calibration of Johnson Noise Power Thermometers (JNPT) and other applications requiring a stable, wide band, well-defined noise power spectral density. The noise source is based on the fact that the open-circuit thermal noise voltage of a feedback resistor, connecting the output to the input of a special inverting amplifier, is available at the amplifier output from an equivalent low output impedance caused by the feedback mechanism. The noise power spectral density level at the noise source output is equivalent to the density of the open-circuit thermal noise or a 100 ohm resistor at a temperature of approximately 64,000 Kelvins. The noise source has an output power spectral density that is flat to within 0.1% (0.0043 db) in the frequency range of from 1 KHz to 100 KHz which brackets typical passbands of the signal-processing channels of JNPT's. Two embodiments, one of higher accuracy that is suitable for use as a standards instrument and another that is particularly adapted for ambient temperature operation, are illustrated in this application.

  8. Magnetohydrodynamic underwater vehicular propulsion systems

    International Nuclear Information System (INIS)

    Swallom, D.W.; Sadovnik, I.; Gibbs, J.S.; Gurol, H.; Nguyen, L.

    1990-01-01

    The development of magnetohydrodynamic propulsion systems for underwater vehicles is discussed. According to the authors, it is a high risk endeavor that offers the possibility of a number of significant advantages over conventional propeller propulsion systems. These advantages may include the potential for greater stealth characteristics, increased maneuverability, enhanced survivability, elimination of cavitation limits, and addition of a significant emergency propulsion system. The possibility of increased stealth is by far the most important advantage. A conceptual design study has been completed with numerical results that shows that these advantages may be obtained with a magnetohydrodynamic propulsion system in an annular configuration externally surrounding a generic study submarine that is neutrally buoyant and can operate with the existing submarine propulsion system power plant. The classical submarine mission requirements make the use of these characteristics of the magnetohydrodynamic propulsion system particularly appropriate for submarine missions. The magnetohydrodynamic annular propulsion system for a generic attack class submarine has been designed to take advantage of the magnetohydrodynamic thruster characteristics

  9. Routing strategies for underwater gliders

    Science.gov (United States)

    Davis, Russ E.; Leonard, Naomi E.; Fratantoni, David M.

    2009-02-01

    Gliders are autonomous underwater vehicles that achieve long operating range by moving at speeds comparable to those of, or slower than, typical ocean currents. This paper addresses routing gliders to rapidly reach a specified waypoint or to maximize the ability to map a measured field, both in the presence of significant currents. For rapid transit in a frozen velocity field, direct minimization of travel time provides a trajectory "ray" equation. A simpler routing algorithm that requires less information is also discussed. Two approaches are developed to maximize the mapping ability, as measured by objective mapping error, of arrays of vehicles. In order to produce data sets that are readily interpretable, both approaches focus sampling near predetermined "ideal tracks" by measuring mapping skill only on those tracks, which are laid out with overall mapping skill in mind. One approach directly selects each vehicle's headings to maximize instantaneous mapping skill integrated over the entire array. Because mapping skill decreases when measurements are clustered, this method automatically coordinates glider arrays to maintain spacing. A simpler method that relies on manual control for array coordination employs a first-order control loop to balance staying close to the ideal track and maintaining vehicle speed to maximize mapping skill. While the various techniques discussed help in dealing with the slow speed of gliders, nothing can keep performance from being degraded when current speeds are comparable to vehicle speed. This suggests that glider utility could be greatly enhanced by the ability to operate high speeds for short periods when currents are strong.

  10. Relationships between inherent optical properties in the Baltic Sea for application to the underwater imaging problem

    Directory of Open Access Journals (Sweden)

    Sławomir Sagan

    2013-02-01

    Full Text Available Statistical relationships between coefficients of light attenuation, scattering and backscattering at wavelength 550 nm derived from series of optical measurements performed in Baltic Sea waters are presented. The relationships were derived primarily to support data analysis from underwater imaging systems. Comparison of these relations with analogous empirical data from the Atlantic and Pacific Oceans shows that the two sets of relationships are similar, despite the different water types and the various experimental procedures and instrumentation applied. The apparently universal character of the relationships enables an approximate calculation of other optical properties and subsequently of the contrast, signal/noise ratio, visibility range and spatial resolution of underwater imaging systems based on attenuation coefficients at wavelength 550 nm only.

  11. Underwater range-gated laser imaging enhancement based on contrast-limited adaptive histogram equalization

    Science.gov (United States)

    Sun, Liang; Wang, Xinwei; Liu, Xiaoquan; Ren, Pengdao; Lei, Pingshun; You, Ruirong; He, Jun; Zhou, Yan; Liu, Yuliang

    2016-10-01

    Underwater range-gated laser imaging (URGLI) still has some problems like un-uniform light, low brightness and contrast. To solve the problems, a variant of adaptive histogram equalization called contrast limited adaptive histogram equalization (CLAHE) is proposed in this paper. In experiment, using the CLAHE and HE to enhance the images, and evaluate the quality of enhanced images by peak signal to noise ratio (PSNR) and contrast. The result shows that the HE gets the images over-enhanced, while the CLAHE has a good enhancement with compressing the over-enhancement and the influence of un-uniform light. The experimental results demonstrate that the CLAHE has a good result of image enhancement for target detection by underwater range-gated laser imaging system.

  12. High-rate wireless data communications: An underwater acoustic communications framework at the physical layer

    Directory of Open Access Journals (Sweden)

    Bessios Anthony G.

    1996-01-01

    Full Text Available A variety of signal processing functions are performed by Underwater Acoustic Systems. These include: 1 detection to determine presence or absence of information signals in the presence of noise, or an attempt to describe which of a predetermined finite set of possible messages { m i , i , ... , M } the signal represents; 2 estimation of some parameter θ ˆ associated with the received signal (i.e. range, depth, bearing angle, etc.; 3 classification and source identification; 4 dynamics tracking; 5 navigation (collision avoidance and terminal guidance; 6 countermeasures; and 7 communications. The focus of this paper is acoustic communications. There is a global current need to develop reliable wireless digital communications for the underwater environment, with sufficient performance and efficiency to substitute for costly wired systems. One possible goal is a wireless system implementation that insures underwater terminal mobility. There is also a vital need to improve the performance of the existing systems in terms of data-rate, noise immunity, operational range, and power consumption, since, in practice, portable high-speed, long range, compact, low-power systems are desired. We concede the difficulties associated with acoustic systems and concentrate on the development of robust data transmission methods anticipating the eventual need for real time or near real time video transmission. An overview of the various detection techniques and the general statistical digital communication problem is given based on a statistical decision theory framework. The theoretical formulation of the underwater acoustic data communications problem includes modeling of the stochastic channel to incorporate a variety of impairments and environmental uncertainties, and proposal of new compensation strategies for an efficient and robust receiver design.

  13. Survivability design for a hybrid underwater vehicle

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Biao; Wu, Chao; Li, Xiang; Zhao, Qingkai; Ge, Tong [State Key Lab of Ocean Engineering, School of Naval Architecture, Ocean and Civil Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China)

    2015-03-10

    A novel hybrid underwater robotic vehicle (HROV) capable of working to the full ocean depth has been developed. The battery powered vehicle operates in two modes: operate as an untethered autonomous vehicle in autonomous underwater vehicle (AUV) mode and operate under remote control connected to the surface vessel by a lightweight, fiber optic tether in remotely operated vehicle (ROV) mode. Considering the hazardous underwater environment at the limiting depth and the hybrid operating modes, survivability has been placed on an equal level with the other design attributes of the HROV since the beginning of the project. This paper reports the survivability design elements for the HROV including basic vehicle design of integrated navigation and integrated communication, emergency recovery strategy, distributed architecture, redundant bus, dual battery package, emergency jettison system and self-repairing control system.

  14. Survivability design for a hybrid underwater vehicle

    International Nuclear Information System (INIS)

    Wang, Biao; Wu, Chao; Li, Xiang; Zhao, Qingkai; Ge, Tong

    2015-01-01

    A novel hybrid underwater robotic vehicle (HROV) capable of working to the full ocean depth has been developed. The battery powered vehicle operates in two modes: operate as an untethered autonomous vehicle in autonomous underwater vehicle (AUV) mode and operate under remote control connected to the surface vessel by a lightweight, fiber optic tether in remotely operated vehicle (ROV) mode. Considering the hazardous underwater environment at the limiting depth and the hybrid operating modes, survivability has been placed on an equal level with the other design attributes of the HROV since the beginning of the project. This paper reports the survivability design elements for the HROV including basic vehicle design of integrated navigation and integrated communication, emergency recovery strategy, distributed architecture, redundant bus, dual battery package, emergency jettison system and self-repairing control system

  15. Recent developments in underwater repair welding

    International Nuclear Information System (INIS)

    Offer, H.P.; Chapman, T.L.; Willis, E.R.; Maslakowski, J.; Van Diemen, P.; Smith, B.W.

    2001-01-01

    As nuclear plants age and reactor internal components begin to show increased evidence of age-related phenomena such as corrosion and fatigue, interest in the development of cost-effective mitigation and repair remedies grows. One technology currently receiving greater development and application program focus is underwater welding. Underwater welding, as used herein, is the application of weld metal to a substrate surface that is wet, but locally dry in the immediate area surrounding the welding torch. The locally dry environment is achieved by the use of a mechanical device that is specifically designed for water exclusion from the welding torch, surface to be welded, and the welding groove. This paper will explore recent developments in the use of underwater welding as a mitigation and repair technique. (author)

  16. Noise Protection

    Science.gov (United States)

    1980-01-01

    Environmental Health Systems puts forth an increasing effort in the U.S. to develop ways of controlling noise, particularly in industrial environments due to Federal and State laws, labor union insistence and new findings relative to noise pollution impact on human health. NASA's Apollo guidance control system aided in the development of a noise protection product, SMART. The basis of all SMART products is SMART compound a liquid plastic mixture with exceptional energy/sound absorbing qualities. The basic compound was later refined for noise protection use.

  17. Underwater radiated noise from Point Absorbing Wave Energy Converters : Noise Characteristics and Possible Environmental Effects

    OpenAIRE

    Haikonen, Kalle

    2014-01-01

    The conversion of wave energy into electrical energy has the potential to become a clean and sustainable form of renewable energy conversion. However, like all forms of energy conversion it will inevitably have an impact on the marine environment, although not in the form of emissions of hazardous substances (gases, oils or chemicals associated with anticorrosion). Possible environmental issues associated with wave energy conversion include electromagnetic fields, alteration of sedimentation ...

  18. Efficient Modelling Methodology for Reconfigurable Underwater Robots

    DEFF Research Database (Denmark)

    Nielsen, Mikkel Cornelius; Blanke, Mogens; Schjølberg, Ingrid

    2016-01-01

    This paper considers the challenge of applying reconfigurable robots in an underwater environment. The main result presented is the development of a model for a system comprised of N, possibly heterogeneous, robots dynamically connected to each other and moving with 6 Degrees of Freedom (DOF......). This paper presents an application of the Udwadia-Kalaba Equation for modelling the Reconfigurable Underwater Robots. The constraints developed to enforce the rigid connection between robots in the system is derived through restrictions on relative distances and orientations. To avoid singularities...... in the orientation and, thereby, allow the robots to undertake any relative configuration the attitude is represented in Euler parameters....

  19. Underwater laser cutting of metallic structures

    International Nuclear Information System (INIS)

    Alfille, J.P.; Schildknecht, J.; Ramaswami, V.S.

    1993-01-01

    In the frame of an european contract, the feasibility of the underwater cutting with a CO 2 laser power is studied. The aim of this work is the dismantling metallic structures of reactors pools. The paper analyzes the general concept of the experimental device, the underwater cutting head, the experimenting vessel, examples of cuttings in dismantling situation with a 500 W CO 2 laser, and examples of cuttings with a 5 kW CO 2 laser. (author). 2 refs., 9 figs., 2 tabs

  20. Ambient environment in the coal mining complexes

    International Nuclear Information System (INIS)

    Singh, V.K.

    1998-01-01

    Environment is all pervading and therefore associated with all individuals. The ambient environment with respect to any activity lies a little outside and the receiving body outside the active zone denotes ambient environment. Basically, air quality and noise level are two physical ingredients whose assessment gives an idea of impact on the ambience. Though largely blamed for polluted conditions, the general ambient conditions in the coal fields do not show a tardy image. Being a low level dispersion industry, its impact remains concentrated in the active core zone. This has been brought out here. The paper presents the status of air quality, and noise level in some coal fields in India. It also discloses a brighter future and sustainable development due to increased concern for environment. (author)

  1. An inexpensive sensor for noise.

    Science.gov (United States)

    Hallett, Laura; Tatum, Marcus; Thomas, Geb; Sousan, Sinan; Koehler, Kirsten; Peters, Thomas

    2018-02-08

    Noise is a pervasive workplace hazard that varies spatially and temporally. The cost of direct-reading instruments for noise hampers their use in a network. The objectives for this work were to (1) develop an inexpensive noise sensor (noise sensors for use in an inexpensive sensor network. The inexpensive noise sensor consists of an electret condenser microphone, an amplifier circuit, and a microcontroller with a small form factor (28 mm by 47 mm by 9 mm) than can be operated as a stand-alone unit. Laboratory tests were conducted to evaluate 50 of the new sensors at 5 sound levels: (1) ambient sound in a quiet office; (2) a pink noise test signal from 65 to 85 dBA in 10 dBA increments; and (3) 94 dBA using a SLM calibrator. Ninety-four percent of the noise sensors (n = 46) were within ± 2 dBA of the SLM for sound levels from 65 dBA to 94 dBA. As sound level increased, bias decreased, ranging from 18.3% in the quiet office to 0.48% at 94 dBA. Overall bias of the sensors was 0.83% across the 75 dBA to 94 dBA range. These sensors are available for a variety of uses and can be customized for many applications, including incorporation into a stationary sensor network for continuous monitoring of noise in manufacturing environments.

  2. Improving Passive Time Reversal Underwater Acoustic Communications Using Subarray Processing

    Directory of Open Access Journals (Sweden)

    Chengbing He

    2017-04-01

    Full Text Available Multichannel receivers are usually employed in high-rate underwater acoustic communication to achieve spatial diversity. In the context of multichannel underwater acoustic communications, passive time reversal (TR combined with a single-channel adaptive decision feedback equalizer (TR-DFE is a low-complexity solution to achieve both spatial and temporal focusing. In this paper, we present a novel receiver structure to combine passive time reversal with a low-order multichannel adaptive decision feedback equalizer (TR-MC-DFE to improve the performance of the conventional TR-DFE. First, the proposed method divides the whole received array into several subarrays. Second, we conduct passive time reversal processing in each subarray. Third, the multiple subarray outputs are equalized with a low-order multichannel DFE. We also investigated different channel estimation methods, including least squares (LS, orthogonal matching pursuit (OMP, and improved proportionate normalized least mean squares (IPNLMS. The bit error rate (BER and output signal-to-noise ratio (SNR performances of the receiver algorithms are evaluated using simulation and real data collected in a lake experiment. The source-receiver range is 7.4 km, and the data rate with quadrature phase shift keying (QPSK signal is 8 kbits/s. The uncoded BER of the single input multiple output (SIMO systems varies between 1 × 10 − 1 and 2 × 10 − 2 for the conventional TR-DFE, and between 1 × 10 − 2 and 1 × 10 − 3 for the proposed TR-MC-DFE when eight hydrophones are utilized. Compared to conventional TR-DFE, the average output SNR of the experimental data is enhanced by 3 dB.

  3. Environmental Noise

    Science.gov (United States)

    Rumberg, Martin

    Environmental noise may be defined as unwanted sound that is caused by emissions from traffic (roads, air traffic corridors, and railways), industrial sites and recreational infrastructures, which may cause both annoyance and damage to health. Noise in the environment or community seriously affects people, interfering with daily activities at school, work and home and during leisure time.

  4. IVO develops a new repair technique for underwater sites. Viscous doughlike substance underwater cracks

    Energy Technology Data Exchange (ETDEWEB)

    Klingstedt, G.; Leisio, C. [ed.

    1998-07-01

    A viscous sealant is revolutionizing repair of the stone and concrete masonry of underwater dams, bridges and canals. There is now no need for expensive and time-consuming cofferdams, since a diver can extrude quick-setting mortar into underwater structures needing repair. This technique has worked well in recent years in various parts of Finland even in strongly flowing water. IVO experts are now starting to look more beyond the borders of Finland

  5. A Support Vector Learning-Based Particle Filter Scheme for Target Localization in Communication-Constrained Underwater Acoustic Sensor Networks.

    Science.gov (United States)

    Li, Xinbin; Zhang, Chenglin; Yan, Lei; Han, Song; Guan, Xinping

    2017-12-21

    Target localization, which aims to estimate the location of an unknown target, is one of the key issues in applications of underwater acoustic sensor networks (UASNs). However, the constrained property of an underwater environment, such as restricted communication capacity of sensor nodes and sensing noises, makes target localization a challenging problem. This paper relies on fractional sensor nodes to formulate a support vector learning-based particle filter algorithm for the localization problem in communication-constrained underwater acoustic sensor networks. A node-selection strategy is exploited to pick fractional sensor nodes with short-distance pattern to participate in the sensing process at each time frame. Subsequently, we propose a least-square support vector regression (LSSVR)-based observation function, through which an iterative regression strategy is used to deal with the distorted data caused by sensing noises, to improve the observation accuracy. At the same time, we integrate the observation to formulate the likelihood function, which effectively update the weights of particles. Thus, the particle effectiveness is enhanced to avoid "particle degeneracy" problem and improve localization accuracy. In order to validate the performance of the proposed localization algorithm, two different noise scenarios are investigated. The simulation results show that the proposed localization algorithm can efficiently improve the localization accuracy. In addition, the node-selection strategy can effectively select the subset of sensor nodes to improve the communication efficiency of the sensor network.

  6. Evidence that ship noise increases stress in right whales.

    Science.gov (United States)

    Rolland, Rosalind M; Parks, Susan E; Hunt, Kathleen E; Castellote, Manuel; Corkeron, Peter J; Nowacek, Douglas P; Wasser, Samuel K; Kraus, Scott D

    2012-06-22

    Baleen whales (Mysticeti) communicate using low-frequency acoustic signals. These long-wavelength sounds can be detected over hundreds of kilometres, potentially allowing contact over large distances. Low-frequency noise from large ships (20-200 Hz) overlaps acoustic signals used by baleen whales, and increased levels of underwater noise have been documented in areas with high shipping traffic. Reported responses of whales to increased noise include: habitat displacement, behavioural changes and alterations in the intensity, frequency and intervals of calls. However, it has been unclear whether exposure to noise results in physiological responses that may lead to significant consequences for individuals or populations. Here, we show that reduced ship traffic in the Bay of Fundy, Canada, following the events of 11 September 2001, resulted in a 6 dB decrease in underwater noise with a significant reduction below 150 Hz. This noise reduction was associated with decreased baseline levels of stress-related faecal hormone metabolites (glucocorticoids) in North Atlantic right whales (Eubalaena glacialis). This is the first evidence that exposure to low-frequency ship noise may be associated with chronic stress in whales, and has implications for all baleen whales in heavy ship traffic areas, and for recovery of this endangered right whale population.

  7. Underwater Advanced Time-Domain Electromagnetic System

    Science.gov (United States)

    2017-03-03

    sufficiently waterproofed ...................................................................... 20 Objective: Calibration method can be used both topside... additional background variability is observed at early times, as illustrated in Figure 15. The layout of this figure is the same as Figure 14. Now the...are discussed in the following sections and summarized in Table 5. Objective: System is sufficiently waterproofed The array remained underwater up to

  8. Underwater Adhesives Retrofit Pipelines with Advanced Sensors

    Science.gov (United States)

    2015-01-01

    Houston-based Astro Technology Inc. used a partnership with Johnson Space Center to pioneer an advanced fiber-optic monitoring system for offshore oil pipelines. The company's underwater adhesives allow it to retrofit older deepwater systems in order to measure pressure, temperature, strain, and flow properties, giving energy companies crucial data in real time and significantly decreasing the risk of a catastrophe.

  9. Detection of Underwater UXOs in Mud

    Science.gov (United States)

    2013-04-01

    2nd International Conference on Underwater Acoustic Measurements, Crete, Greece, 2007. 16 [10] P.T. Gough and D.W. Hawkins “Imaging algorithms...course. Runs 275 and 325 folla.v the same trad < and run 322 foUows a track on the opposite side of the swath. The LF SAS image of run 325 is shown

  10. Adaptive turbo equalization for underwater acoustic communication

    NARCIS (Netherlands)

    Cannelli, L; Leus, G.; Dol, H.S.; Walree, P.A. van

    2013-01-01

    In this paper a multiband transceiver designed for underwater channels is presented. Multi-branch filtering at the receiver is used to leverage the diversity offered by a multi-scale multi-lag scenario. The multi-branch bank of filters is constructed by estimating scale and delay coefficients

  11. Evolution: Fossil Ears and Underwater Sonar.

    Science.gov (United States)

    Lambert, Olivier

    2016-08-22

    A key innovation in the history of whales was the evolution of a sonar system together with high-frequency hearing. Fossils of an archaic toothed whale's inner ear bones provide clues for a stepwise emergence of underwater echolocation ability. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. HARDWARE REALIZATION OF CANNY EDGE DETECTION ALGORITHM FOR UNDERWATER IMAGE SEGMENTATION USING FIELD PROGRAMMABLE GATE ARRAYS

    Directory of Open Access Journals (Sweden)

    ALEX RAJ S. M.

    2017-09-01

    Full Text Available Underwater images raise new challenges in the field of digital image processing technology in recent years because of its widespread applications. There are many tangled matters to be considered in processing of images collected from water medium due to the adverse effects imposed by the environment itself. Image segmentation is preferred as basal stage of many digital image processing techniques which distinguish multiple segments in an image and reveal the hidden crucial information required for a peculiar application. There are so many general purpose algorithms and techniques that have been developed for image segmentation. Discontinuity based segmentation are most promising approach for image segmentation, in which Canny Edge detection based segmentation is more preferred for its high level of noise immunity and ability to tackle underwater environment. Since dealing with real time underwater image segmentation algorithm, which is computationally complex enough, an efficient hardware implementation is to be considered. The FPGA based realization of the referred segmentation algorithm is presented in this paper.

  13. Direct observation of microcavitation in underwater adhesion of mushroom-shaped adhesive microstructure

    Directory of Open Access Journals (Sweden)

    Lars Heepe

    2014-06-01

    Full Text Available In this work we report on experiments aimed at testing the cavitation hypothesis [Varenberg, M.; Gorb, S. J. R. Soc., Interface 2008, 5, 383–385] proposed to explain the strong underwater adhesion of mushroom-shaped adhesive microstructures (MSAMSs. For this purpose, we measured the pull-off forces of individual MSAMSs by detaching them from a glass substrate under different wetting conditions and simultaneously video recording the detachment behavior at very high temporal resolution (54,000–100,000 fps. Although microcavitation was observed during the detachment of individual MSAMSs, which was a consequence of water inclusions present at the glass–MSAMS contact interface subjected to negative pressure (tension, the pull-off forces were consistently lower, around 50%, of those measured under ambient conditions. This result supports the assumption that the recently observed strong underwater adhesion of MSAMS is due to an air layer between individual MSAMSs [Kizilkan, E.; Heepe, L.; Gorb, S. N. Underwater adhesion of mushroom-shaped adhesive microstructure: An air-entrapment effect. In Biological and biomimetic adhesives: Challenges and opportunities; Santos, R.; Aldred, N.; Gorb, S. N.; Flammang, P., Eds.; The Royal Society of Chemistry: Cambridge, U.K., 2013; pp 65–71] rather than by cavitation. These results obtained due to the high-speed visualisation of the contact behavior at nanoscale-confined interfaces allow for a microscopic understanding of the underwater adhesion of MSAMSs and may aid in further development of artificial adhesive microstructures for applications in predominantly liquid environments.

  14. The alkaline aluminium/hydrogen peroxide power source in the Hugin II unmanned underwater vehicle

    Science.gov (United States)

    Hasvold, Øistein; Johansen, Kjell Håvard; Mollestad, Ole; Forseth, Sissel; Størkersen, Nils

    In 1993, The Norwegian Defence Research Establishment (FFI) demonstrated AUV-Demo, an unmanned (untethered) underwater vehicle (UUV), powered by a magnesium/dissolved oxygen seawater battery (SWB). This technology showed that an underwater range of at least 1000 nautical miles at a speed of 4 knots was possible, but also that the maximum hotel load this battery system could support was very limited. Most applications for UUV technology need more power over a shorter period of time. Seabed mapping using a multibeam echo sounder mounted on an UUV was identified as a viable application and the Hugin project was started in 1995 in cooperation with Norwegian industry. For this application, an endurance of 36 h at 4 knots was required. Development of the UUV hull and electronics system resulted in the UUV Hugin I. It carries a Ni/Cd battery of 3 kW h, allowing up to 6 h under-water endurance. In parallel, we developed a battery based on a combination of alkaline Al/air and SWB technology, using a circulating alkaline electrolyte, aluminium anodes and maintaining the oxidant concentration in the electrolyte by continuously adding hydrogen peroxide (HP) to the electrolyte. This concept resulted in a safe battery, working at ambient pressure (balanced) and with sufficient power and energy density to allow the UUV Hugin II to make a number of successive dives, each of up to 36 h duration and with only 1 h deck time between dives for HP refill and electrolyte exchange. After 100 h, an exchange of anodes takes place. The power source consists of a four-cell Al/HP battery, a DC/DC converter delivering 600 W at 30 V, circulation and dosing pumps and a battery control unit. Hugin II is now in routine use by the Norwegian Underwater Intervention AS (NUI) which operates the UUV for high-precision seabed mapping down to a water depth of 600 m.

  15. Long-term Self-noise Estimates of Seismic Sensors From a High-noise Vault

    Science.gov (United States)

    Hicks, S. P.; Goessen, S.; Hill, P.; Rietbrock, A.

    2017-12-01

    To understand the detection capabilities of seismic stations and for reducing biases in ambient noise imaging, it is vital to assess the contribution of instrument self-noise to overall site noise. Self-noise estimates typically come from vault installations in continental interiors with very low ambient noise levels. However, this approach restricts the independent assessment of self-noise by individual end-users to assess any variations in their own instrument pools from nominal specifications given by manufacturers and from estimations given in comparative test papers. However, the calculation method should be adapted to variable installation conditions. One problem is that microseism noise can contaminate self-noise results caused by instrument misalignment errors or manufacturing limits; this effect becomes stronger where ambient noise is higher. Moreover, due to expected stochastic and time-varying sensor noise, estimates based on hand-picking small numbers of data segments may not accurately reflect true self-noise. We report on results from a self-noise test experiment of Güralp seismic instruments (3T, 3ESPC broadband seismometers, Fortis strong motion accelerometer) that were installed in the sub-surface vault of the Eskdalemuir Seismic Observatory in Scotland, UK over the period October 2016-August 2017. Due to vault's proximity to the ocean, secondary microseism noise is strong, so we efficiently compute the angle of misalignment that maximises waveform coherence with a reference sensor. Self-noise was calculated using the 3-sensor correlation technique and we compute probability density functions of self-noise to assess its spread over time. We find that not correcting for misalignments as low as 0.1° can cause self-noise to be artificially higher by up to 15 dB at frequencies of 0.1-1 Hz. Our method thus efficiently removes the effect of microseism contamination on self-noise; for example, it restores the minimum noise floor for a 360s - 50 Hz 3T to

  16. Stability analysis of hybrid-driven underwater glider

    Science.gov (United States)

    Niu, Wen-dong; Wang, Shu-xin; Wang, Yan-hui; Song, Yang; Zhu, Ya-qiang

    2017-10-01

    Hybrid-driven underwater glider is a new type of unmanned underwater vehicle, which combines the advantages of autonomous underwater vehicles and traditional underwater gliders. The autonomous underwater vehicles have good maneuverability and can travel with a high speed, while the traditional underwater gliders are highlighted by low power consumption, long voyage, long endurance and good stealth characteristics. The hybrid-driven underwater gliders can realize variable motion profiles by their own buoyancy-driven and propeller propulsion systems. Stability of the mechanical system determines the performance of the system. In this paper, the Petrel-II hybrid-driven underwater glider developed by Tianjin University is selected as the research object and the stability of hybrid-driven underwater glider unitedly controlled by buoyancy and propeller has been targeted and evidenced. The dimensionless equations of the hybrid-driven underwater glider are obtained when the propeller is working. Then, the steady speed and steady glide path angle under steady-state motion have also been achieved. The steady-state operating conditions can be calculated when the hybrid-driven underwater glider reaches the desired steady-state motion. And the steadystate operating conditions are relatively conservative at the lower bound of the velocity range compared with the range of the velocity derived from the method of the composite Lyapunov function. By calculating the hydrodynamic coefficients of the Petrel-II hybrid-driven underwater glider, the simulation analysis has been conducted. In addition, the results of the field trials conducted in the South China Sea and the Danjiangkou Reservoir of China have been presented to illustrate the validity of the analysis and simulation, and to show the feasibility of the method of the composite Lyapunov function which verifies the stability of the Petrel-II hybrid-driven underwater glider.

  17. Uso de ardósia na construção de celas de maternidade para suínos: II - ambiente térmico e avaliação dos ruídos Use of slate to built swine nursery cells: II - thermal environment and noise evaluation

    Directory of Open Access Journals (Sweden)

    Jaqueline de O. Castro

    2013-02-01

    Full Text Available Este trabalho teve o objetivo de avaliar o ambiente térmico e o ruído em celas de maternidade para suínos com divisórias de alvenaria ou com rochas de ardósia. Para as medidas das variáveis de conforto térmico e de ruídos, utilizaram-se de termômetros e decibelímetro. No interior das celas e para a análise estatística, foram usados doze matrizes e cento e trinta e nove leitões, distribuídos em delineamento em blocos casualizados, em esquema de parcelas subdivididas. Os resultados mostraram que, no período da manhã, em ambos os tratamentos, as condições de conforto térmico foram mais adequadas para as matrizes, enquanto no período da tarde, mais adequadas para os leitões; com relação ao ruído, este foi menor nas celas de alvenaria. De forma geral, o ambiente no interior das celas construídas em ardósia apresentou umidade relativa mais baixa, e ITGU e temperatura mais elevada que as celas construídas em alvenaria. O nível de ruídos permaneceu dentro dos limites considerados ideais para suínos em ambos os tratamentos.The aim of the present study was to evaluate the thermal environment and noise levels in swine farrowing cells built with masonry or slate. Thermometers and sound level meter equipment were used to measure the thermal comfort variables. Inside the cells and for the statistical analysis, twelve sows and one hundred thirty-nine piglets were used, distributed in a randomized blocks design in a split-plot arrangement. The results showed that in the morning, in both treatments, the thermal comfort conditions were more suitable for sows, while in the afternoon it was more suitable for piglets. The noise was lower in the masonry cells. Overall, the environment inside in the cells built with slate presented lower relative humidity and, higher BGHI and temperature than those built with masonry. The noise level remained within the thresholds considered as ideal for swine in both treatments.

  18. Impact of noise on hearing amongst commercial motor bike riders in ...

    African Journals Online (AJOL)

    The ambient noise level and noise-induced hearing impairment (NIHI) in 200 motorbike riders from six motorbike parks were evaluated. All were males aged between 20- 62 years. Subjects were sampled using a cluster sampling technique. Parameters measured were environmental noise using the noise meter (peters) ...

  19. Noise-Induced Hearing Loss - A Preventable Disease?

    DEFF Research Database (Denmark)

    Frederiksen, Thomas W.; Ramlau-Hansen, Cecilia H.; Stokholm, Zara A.

    2017-01-01

    statistically significant among baseline participants with first exposure before the 1980s (odds ratio: 1.90, 95% CI: 1.11; 3.22). CONCLUSIONS: We observed declining industrial noise levels, increased use of HPD and no significant impact on hearing thresholds from current ambient industrial noise levels, which...... insignificant, inverse association between higher ambient cumulative noise exposure and poorer hearing (-0.10 dB hearing threshold shift per dB-year (95% confidence interval (CI): -0.36; 0.16)). The risk of hearing loss seemed to increase with earlier first year of noise exposure, but odds ratios were only...

  20. Underwater videography and photography in Gulf of Kachchh. Sponsored by Gujarat Ecological Society, Vadodara, Gujarat

    Digital Repository Service at National Institute of Oceanography (India)

    Marine Archaeology Centre (MAC) has been carrying out underwater explorations and excavations of ancient ports and sunken shipwrecks to preserve underwater cultural heritage. MAC has the infrastructure facility to carry out underwater investigations...

  1. Hydrodynamic Coefficients Identification and Experimental Investigation for an Underwater Vehicle

    Directory of Open Access Journals (Sweden)

    Shaorong XIE

    2014-02-01

    Full Text Available Hydrodynamic coefficients are the foundation of unmanned underwater vehicles modeling and controller design. In order to reduce identification complexity and acquire necessary hydrodynamic coefficients for controllers design, the motion of the unmanned underwater vehicle was separated into vertical motion and horizontal motion models. Hydrodynamic coefficients were regarded as mapping parameters from input forces and moments to output velocities and acceleration of the unmanned underwater vehicle. The motion models of the unmanned underwater vehicle were nonlinear and Genetic Algorithm was adopted to identify those hydrodynamic coefficients. To verify the identification quality, velocities and acceleration of the unmanned underwater vehicle was measured using inertial sensor under the same conditions as Genetic Algorithm identification. Curves similarity between measured velocities and acceleration and those identified by Genetic Algorithm were used as optimizing standard. It is found that the curves similarity were high and identified hydrodynamic coefficients of the unmanned underwater vehicle satisfied the measured motion states well.

  2. Delay Tolerance in Underwater Wireless Communications: A Routing Perspective

    Directory of Open Access Journals (Sweden)

    Safdar Hussain Bouk

    2016-01-01

    Full Text Available Similar to terrestrial networks, underwater wireless networks (UWNs also aid several critical tasks including coastal surveillance, underwater pollution detection, and other maritime applications. Currently, once underwater sensor nodes are deployed at different levels of the sea, it is nearly impossible or very expensive to reconfigure the hardware, for example, battery. Taking this issue into account, considerable amount of research has been carried out to ensure minimum energy costs and reliable communication between underwater nodes and base stations. As a result, several different network protocols were proposed for UWN, including MAC, PHY, transport, and routing. Recently, a new paradigm was introduced claiming that the intermittent nature of acoustic channel and signal resulted in designing delay tolerant routing schemes for the UWN, known as an underwater delay tolerant network. In this paper, we provide a comprehensive survey of underwater routing protocols with emphasis on the limitations, challenges, and future open issues in the context of delay tolerant network routing.

  3. A Novel Method to Predict Circulation Control Noise

    Science.gov (United States)

    2016-03-17

    sea-based vehicles as t heir sonar sys- tems can be limited by self noise. In addition, stealth is vital to missions of many underwater craft and...anemom-:Jtry. Hotwire anemometry operates on the principle relating the thermal loss of a heated resistance sensor to the convective effects of the...limit to this however , as thermal changes of the probe supports can influence measurements if a certain temperature is exceeded. In addition, it is

  4. Drone noise

    Science.gov (United States)

    Tinney, Charles; Sirohi, Jayant; University of Texas at Austin Team

    2017-11-01

    A basic understanding of the noise produced by single and multirotor drones operating at static thrust conditions is presented. This work acts as an extension to previous efforts conducted at The University of Texas at Austin (Tinney et al. 2017, AHS Forum 73). Propeller diameters ranging from 8 inch to 12 inch are examined for configurations comprising an isolated rotor, a quadcopter configuration and a hexacopter configuration, and with a constant drone pitch of 2.25. An azimuthal array of half-inch microphones, placed between 2 and 3 hub-center diameters from the drone center, are used to assess the acoustic near-field. Thrust levels, acquired using a six degree-of-freedom load cell, are then used to correlate acoustic noise levels to aerodynamic performance for each drone configuration. The findings reveal a nearly logarithmic increase in noise with increasing thrust. However, for the same thrust condition, considerable noise reduction is achieved by increasing the number of propeller blades thereby reducing the blade passage frequency and both the thickness and loading noise sources that accompany it.

  5. Adaptive Suppression of Noise in Voice Communications

    Science.gov (United States)

    Kozel, David; DeVault, James A.; Birr, Richard B.

    2003-01-01

    A subsystem for the adaptive suppression of noise in a voice communication system effects a high level of reduction of noise that enters the system through microphones. The subsystem includes a digital signal processor (DSP) plus circuitry that implements voice-recognition and spectral- manipulation techniques. The development of the adaptive noise-suppression subsystem was prompted by the following considerations: During processing of the space shuttle at Kennedy Space Center, voice communications among test team members have been significantly impaired in several instances because some test participants have had to communicate from locations with high ambient noise levels. Ear protection for the personnel involved is commercially available and is used in such situations. However, commercially available noise-canceling microphones do not provide sufficient reduction of noise that enters through microphones and thus becomes transmitted on outbound communication links.

  6. An Evaluation of Potential Operating Systems for Autonomous Underwater Vehicles

    Science.gov (United States)

    2013-02-01

    remote control of such vehicles requires the use of a tether , limiting the vehicle’s range; however operating underwater vehicles autonomously requires...URBI Universal Robot Body Interface UUV Unmanned Underwater Vehicle UNCLASSIFIED xi DSTO–TN–1194 UNCLASSIFIED THIS PAGE IS INTENTIONALLY BLANK xii... underwater environment, where many platforms are still reliant upon an umbilical tether for power and high bandwidth communications. This tether

  7. On the Performance of the Underwater Acoustic Sensor Networks

    Science.gov (United States)

    2015-05-01

    waves for Underwater Wireless Communication (UWC); radio waves, optical waves, and acoustic waves are few to name. Radio waves are good for extra low...2211 underwater communication , wireless sensors, mutual information REPORT DOCUMENTATION PAGE 11. SPONSOR/MONITOR’S REPORT NUMBER(S) 10. SPONSOR...Cotae, “On the Performance of the Underwater Wireless Communication Sensor Networks: Work in Progress” ASEE Mid-Atlantic Fall 2014 Conference

  8. Underwater laser beam welding of Alloy 690

    International Nuclear Information System (INIS)

    Hino, Takehisa; Tamura, Masataka; Kono, Wataru; Kawano, Shohei; Yoda, Masaki

    2009-01-01

    Stress Corrosion Clacking (SCC) has been reported at Alloy 600 welds between nozzles and safe-end in Pressurized Water Reactor (PWR) plant. Alloy 690, which has higher chromium content than Alloy 600, has been applied for cladding on Alloy 600 welds for repairing damaged SCC area. Toshiba has developed Underwater Laser Beam Welding technique. This method can be conducted without draining, so that the repairing period and the radiation exposure during the repair can be dramatically decreased. In some old PWRs, high-sulfur stainless steel is used as the materials for this section. It has a high susceptibility of weld cracks. Therefore, the optimum welding condition of Alloy 690 on the high-sulfur stainless steel was investigated with our Underwater Laser Beam Welding unit. Good cladding layer, without any crack, porosity or lack of fusion, could be obtained. (author)

  9. Ocean Research Enabled by Underwater Gliders

    Science.gov (United States)

    Rudnick, Daniel L.

    2016-01-01

    Underwater gliders are autonomous underwater vehicles that profile vertically by changing their buoyancy and use wings to move horizontally. Gliders are useful for sustained observation at relatively fine horizontal scales, especially to connect the coastal and open ocean. In this review, research topics are grouped by time and length scales. Large-scale topics addressed include the eastern and western boundary currents and the regional effects of climate variability. The accessibility of horizontal length scales of order 1 km allows investigation of mesoscale and submesoscale features such as fronts and eddies. Because the submesoscales dominate vertical fluxes in the ocean, gliders have found application in studies of biogeochemical processes. At the finest scales, gliders have been used to measure internal waves and turbulent dissipation. The review summarizes gliders' achievements to date and assesses their future in ocean observation.

  10. A MAC protocol for underwater sensors networks

    OpenAIRE

    Santos, Rodrigo; Orozco, Javier; Ochoa, Sergio; Meseguer Pallarès, Roc; Eggly, Gabriel

    2015-01-01

    “The final publication is available at Springer via http://dx.doi.org/10.1007/978-3-319-26401-1_37." Underwater sensor networks are becoming an important field of research, because of its everyday increasing application scope. Examples of their application areas are environmental and pollution monitoring (mainly oil spills), oceanographic data collection, support for submarine geo-localization, ocean sampling and early tsunamis alert. It is well-known the challenge that represents to perfo...

  11. Passive Mode Carbon Nanotube Underwater Acoustic Transducer

    Science.gov (United States)

    2016-09-20

    irreversible Joule heat) by an electric light bulb . The reciprocal (or reverse) of this process by supplying heat and shining light to the same electric bulb ...limit the invention to the precise form disclosed; and obviously many modifications and variations are possible in light of the above teaching...300151 1 of 14 PASSIVE MODE CARBON NANOTUBE UNDERWATER ACOUSTIC TRANSDUCER STATEMENT OF GOVERNMENT INTEREST [0001] The invention described

  12. Underwater suction device for irradiated materials

    International Nuclear Information System (INIS)

    Qurnell, F.D.; Peloquin, A.V.

    1982-01-01

    An underwater suction device for collecting irradiated materials in a pool of water includes injection and suction tubes and a removable, disposable filter for capturing irradiated materials. Pressurized water is injected into the suction tube through a jet pump nozzle to establish a suction flow through the tube. The suction device is manoeuverable by a pole, which is pivotally connected to the suction device by a latching mechanism. (author)

  13. Tethered Antennas for Unmanned Underwater Vehicles

    Science.gov (United States)

    2009-04-27

    Concepts The first design (Figure 1) was based on the concept of an airfoil kite. The shape of the tow body was built around a NACA5515 hydrofoil to...Underwater Vehicles Brooke Ocean Technology (USA) Inc. 6 Figure 1: Hydrofoil Design The second design was based on that of a boat hull...communications. A sharp bow was utilized to cut through the water to reduce drag when on the surface. Like the hydrofoil design the top profile was

  14. MEDITERRANEAN: Underwater neutrinos get off the ground

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    Now funded is the initial stage of NESTOR, an imaginative new programme for a dedicated underwater neutrino astroparticle physics laboratory. Located in the international waters off the southernmost corner of continental Europe near the town of Pylos in S.W. Greece, NESTOR (NEutrinos from Supernovae and TeV sources Ocean Range) recalls the wise king of Pylos who counselled the Greeks during the Trojan war, an excellent tradition for new scientific goals of detecting neutrinos

  15. Role of Confined Water in Underwater Adhesion

    Science.gov (United States)

    Dhinojwala, Ali

    Surface bound water is a strong deterrent for forming strong bonds between two surfaces underwater and expelling that bound water is important for strong adhesion. I will discuss examples of different strategies used by geckos, spiders, and mussels to handle this last layer of bound water. Recent results using infrared-visible sum frequency generation spectroscopy to probe the structure of this bound water will be discussed. National Science Foundation.

  16. Obstacle avoidance in underwater glider path planning

    OpenAIRE

    Isern González, Josep; Hernández Sosa, Daniel; Fernández Perdomo, Enrique; Cabrera Gámez, Jorge; Domínguez Brito, Antonio Carlos; Prieto Marañón, Víctor

    2012-01-01

    Underwater gliders have revealed as a valuable scientific platform, with a growing number of successful environmental sampling applications. They are specially suited for long range missions due to their unmatched autonomy level, although their low surge speed make them strongly affected by ocean currents. Path planning constitute a real concern for this type of vehicle, as it may reduce the time taken to reach a given waypoint or save power. In such a dynamic environment it is not easy to fi...

  17. A Recovery System for Unmanned Underwater Vehicles

    Science.gov (United States)

    2017-09-28

    300170 1 of 10 A RECOVERY SYSTEM FOR UNMANNED UNDERWATER VEHICLES STATEMENT OF GOVERNMENT INTEREST [0001] The invention described herein may...6 of 10 forces cannot be easily predicted and can be strong enough to require a significantly larger handling system and significantly more...the sea state, the ship handling system , the capture mechanism and the design of the capture mechanism 400. [0024] The water jets 100 will increase

  18. Impact of Anthropogenic Noise on Aquatic Animals: From Single Species to Community-Level Effects.

    Science.gov (United States)

    Sabet, Saeed Shafiei; Neo, Yik Yaw; Slabbekoorn, Hans

    2016-01-01

    Anthropogenic noise underwater is on the rise and may affect aquatic animals of marine and freshwater ecosystems. Many recent studies concern some sort of impact assessment of a single species. Few studies addressed the noise impact on species interactions underwater, whereas there are some studies that address community-level impact but only on land in air. Key processes such as predator-prey or competitor interactions may be affected by the masking of auditory cues, noise-related disturbance, or attentional interference. Noise-associated changes in these interactions can cause shifts in species abundance and modify communities, leading to fundamental ecosystem changes. To gain further insight into the mechanism and generality of earlier findings, we investigated the impact on both a predator and a prey species in captivity, zebrafish (Danio rerio) preying on waterfleas (Daphnia magna).

  19. Research on Operational Aspects of Large Autonomous Underwater Glider Fleets

    National Research Council Canada - National Science Library

    Fratantoni, David M

    2007-01-01

    This program supported research on the operational and management issues stemming from application of large fleets of autonomous underwater gliders to oceanographic research and rapid environmental...

  20. Underwater hearing in the great cormorant (Phalacrocorax carbo sinensis)

    DEFF Research Database (Denmark)

    Hansen, Kirstin Anderson; Larsen, Ole Næsbye; Wahlberg, Magnus

    2016-01-01

    The underwater hearing threshold of a great cormorant (Phalacrocroax carbo sinensis) was measured at 2 kHz using psychophysical methods. Previous in-air and underwater testing suggests that cormorants have rather poor in-air hearing compared to other birds of similar size (Johansen, 2016). Prelim......The underwater hearing threshold of a great cormorant (Phalacrocroax carbo sinensis) was measured at 2 kHz using psychophysical methods. Previous in-air and underwater testing suggests that cormorants have rather poor in-air hearing compared to other birds of similar size (Johansen, 2016...

  1. Calibration Techniques for Accurate Measurements by Underwater Camera Systems.

    Science.gov (United States)

    Shortis, Mark

    2015-12-07

    Calibration of a camera system is essential to ensure that image measurements result in accurate estimates of locations and dimensions within the object space. In the underwater environment, the calibration must implicitly or explicitly model and compensate for the refractive effects of waterproof housings and the water medium. This paper reviews the different approaches to the calibration of underwater camera systems in theoretical and practical terms. The accuracy, reliability, validation and stability of underwater camera system calibration are also discussed. Samples of results from published reports are provided to demonstrate the range of possible accuracies for the measurements produced by underwater camera systems.

  2. Calibration Techniques for Accurate Measurements by Underwater Camera Systems

    Directory of Open Access Journals (Sweden)

    Mark Shortis

    2015-12-01

    Full Text Available Calibration of a camera system is essential to ensure that image measurements result in accurate estimates of locations and dimensions within the object space. In the underwater environment, the calibration must implicitly or explicitly model and compensate for the refractive effects of waterproof housings and the water medium. This paper reviews the different approaches to the calibration of underwater camera systems in theoretical and practical terms. The accuracy, reliability, validation and stability of underwater camera system calibration are also discussed. Samples of results from published reports are provided to demonstrate the range of possible accuracies for the measurements produced by underwater camera systems.

  3. Automatic stabilization of underwater robots in the time manipulation operations

    International Nuclear Information System (INIS)

    Filaretov, V.F.; Koval, E.V.

    1994-01-01

    When carrying out underwater technical works by means of an underwater vehicles having a manipulator it is desirable to perform manipulation operations in the regime of the underwater vehicle hovering above the object without durable and complicated operations up its rigid fixation. Underwater vehicle stabilization is achieved by compensation all the effects on the vehicle caused by the operating manipulator in water medium. This automatic stabilization is formed due to input of the required control signals into corresponding vehicle propellers proportional to calculated components of the generalized forces and moments. The propellers should form stops reacting against effects

  4. Contour Tracking Control for the REMUS Autonomous Underwater Vehicle

    National Research Council Canada - National Science Library

    Van Reet, Alan R

    2005-01-01

    In the interest of enhancing the capabilities of autonomous underwater vehicles used in US Naval Operations, controlling vehicle position to follow depth contours presents exciting potential for navigation...

  5. Autopilot Using Differential Thrust for ARIES Autonomous Underwater Vehicle

    National Research Council Canada - National Science Library

    Sarton, Christopher

    2003-01-01

    .... Unfortunately, communication antennas must point to specific satellites in this system and thus underwater vehicles must steer a specific course on the surface during the communication process...

  6. Underwater Acoustic Target Tracking: A Review.

    Science.gov (United States)

    Luo, Junhai; Han, Ying; Fan, Liying

    2018-01-02

    Advances in acoustic technology and instrumentation now make it possible to explore marine resources. As a significant component of ocean exploration, underwater acoustic target tracking has aroused wide attention both in military and civil fields. Due to the complexity of the marine environment, numerous techniques have been proposed to obtain better tracking performance. In this paper, we survey over 100 papers ranging from innovative papers to the state-of-the-art in this field to present underwater tracking technologies. Not only the related knowledge of acoustic tracking instrument and tracking progress is clarified in detail, but also a novel taxonomy method is proposed. In this paper, algorithms for underwater acoustic target tracking are classified based on the methods used as: (1) instrument-assisted methods; (2) mode-based methods; (3) tracking optimization methods. These algorithms are compared and analyzed in the aspect of dimensions, numbers, and maneuvering of the tracking target, which is different from other survey papers. Meanwhile, challenges, countermeasures, and lessons learned are illustrated in this paper.

  7. Underwater detection by using ultrasonic sensor

    Science.gov (United States)

    Bakar, S. A. A.; Ong, N. R.; Aziz, M. H. A.; Alcain, J. B.; Haimi, W. M. W. N.; Sauli, Z.

    2017-09-01

    This paper described the low cost implementation of hardware and software in developing the system of ultrasonic which can visualize the feedback of sound in the form of measured distance through mobile phone and monitoring the frequency of detection by using real time graph of Java application. A single waterproof transducer of JSN-SR04T had been used to determine the distance of an object based on operation of the classic pulse echo detection method underwater. In this experiment, the system was tested by placing the housing which consisted of Arduino UNO, Bluetooth module of HC-06, ultrasonic sensor and LEDs at the top of the box and the transducer was immersed in the water. The system which had been tested for detection in vertical form was found to be capable of reporting through the use of colored LEDs as indicator to the relative proximity of object distance underwater form the sensor. As a conclusion, the system can detect the presence of an object underwater within the range of ultrasonic sensor and display the measured distance onto the mobile phone and the real time graph had been successfully generated.

  8. Modeling and Control of Underwater Robotic Systems

    Energy Technology Data Exchange (ETDEWEB)

    Schjoelberg, I:

    1996-12-31

    This doctoral thesis describes modeling and control of underwater vehicle-manipulator systems. The thesis also presents a model and a control scheme for a system consisting of a surface vessel connected to an underwater robotic system by means of a slender marine structure. The equations of motion of the underwater vehicle and manipulator are described and the system kinematics and properties presented. Feedback linearization technique is applied to the system and evaluated through a simulation study. Passivity-based controllers for vehicle and manipulator control are presented. Stability of the closed loop system is proved and simulation results are given. The equation of motion for lateral motion of a cable/riser system connected to a surface vessel at the top end and to a thruster at the bottom end is described and stability analysis and simulations are presented. The equations of motion in 3 degrees of freedom of the cable/riser, surface vessel and robotic system are given. Stability analysis of the total system with PD-controllers is presented. 47 refs., 32 figs., 7 tabs.

  9. Passive Acoustic Thermometry Using Low-Frequency Deep Water Noise

    Science.gov (United States)

    2015-09-30

    1 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Passive Acoustic Thermometry Using Low-Frequency Deep... thermometry using Cross-correlation processing of deep water ambient noise. OBJECTIVE Our previous research effort has demonstrated that coherent... thermometry using low-frequency deep water ambient noise recorded on the global IMS- CTBTO network Results from this study are expected to help guide the

  10. Noise cancellation in magnetoencephalography and electroencephalography with isolated reference sensors

    Science.gov (United States)

    Kraus, Jr., Robert H.; Espy, Michelle A.; Matlachov, Andrei; Volegov, Petr

    2010-06-01

    An apparatus measures electromagnetic signals from a weak signal source. A plurality of primary sensors is placed in functional proximity to the weak signal source with an electromagnetic field isolation surface arranged adjacent the primary sensors and between the weak signal source and sources of ambient noise. A plurality of reference sensors is placed adjacent the electromagnetic field isolation surface and arranged between the electromagnetic isolation surface and sources of ambient noise.

  11. First indications that northern bottlenose whales are sensitive to behavioural disturbance from anthropogenic noise

    NARCIS (Netherlands)

    Miller, P.J.O.; Kvadsheim, P.H.; Lam, F.P.A.; Tyack, P.L.; Curé, C.; DeRuiter, S.L.; Kleivane, L.; Sivle, L.D.; IJsselmuide, S.P. van; Visser, F.; Wensveen, P.J.; Benda-Beckmann, A.M. von; Martín López, L.M.; Narazaki, T.; Hooker, S.K.

    2015-01-01

    Although northern bottlenose whales were the most heavily hunted beaked whale, we have little information about this species in its remote habitat of the North Atlantic Ocean. Underwater anthropogenic noise and disruption of their natural habitat may be major threats, given the sensitivity of other

  12. Nível de ruído no ambiente de trabalho do professor de educação física em aulas de ciclismo indoor Nivel de ruido en el ambiente de trabajo del profesor de educación física en aulas de ciclismo indoor Level of noise at the workplace environment among physical education teachers in indoor bike classes

    Directory of Open Access Journals (Sweden)

    Alexandre Palma

    2009-04-01

    Full Text Available OBJETIVO: Analisar o nível de ruído no ambiente de trabalho do professor de educação física durante as aulas de ciclismo indoor e sua associação com alguns aspectos da saúde. MÉTODOS: Estudo transversal conduzido com 15 professores de educação física de diferentes academias de ginástica, na cidade do Rio de Janeiro (RJ, em 2007. As características do processo e da organização do trabalho e as queixas de saúde relatadas pelos professores foram coletadas por meio de questionário padronizado. Para verificação dos transtornos psiquiátricos menores foi usado o SRQ-20 (Self-Report Questionnaire. As medidas de pressão sonora foram realizadas em um aparelho portátil. O nível de pressão foi medido em dB(A no nível equivalente de energia em diferentes pontos da sala e momentos da aula. As análises estatísticas utilizadas foram a ANOVA, o qui-quadrado e a correlação de Pearson. RESULTADOS: Os níveis de pressão sonora variaram entre 74,4 dB(A e 101,6 dB(A. Os valores médios encontrados durante as aulas foram: a aquecimento (média= 88,45 dB(A; b parte principal (média= 95,86 dB(A; e, fechamento (média= 85,12 dB(A. O ruído de fundo apresentou o valor médio de 66,89 dB(A. Houve diferenças significativas (pOBJETIVO: Analizar el nivel de ruido en el ambiente de trabajo del profesor de educación física durante las aulas de ciclismo indoor y su asociación con algunos aspectos de la salud. MÉTODOS: Estudio transversal conducido con 15 profesores de educación física de diferentes academias de ejercicio, en la ciudad de Río de Janeiro (Sureste de Brasil, en 2007. Las características del proceso y de la organización de trabajo y los reclamos de salud relatados por los profesores fueron colectados por medio de cuestionario estandarizado. Para verificar los trastornos psiquiátricos menores fue usado el SRQ-20 (Self Report Questionnaire. Las medidas de presión sonora fueron realizadas en un aparato portátil. El nivel de

  13. Atmosphere and Ambient Space

    DEFF Research Database (Denmark)

    Schmidt, Ulrik

    Atmosphere and Ambient Space This paper explores the relation between atmosphere and ambient space. Atmosphere and ambient space share many salient properties. They are both ontologically indeterminate, constantly varying and formally diffuse and they are both experienced as a subtle, non......-signifying property of a given space. But from a certain point of view, the two concepts also designate quite dissimilar experiences of space. To be ’ambient’ means to surround. Accordingly, ambient space is that space, which surrounds something or somebody. (Gibson 1987: 65) Since space is essentially...... of a surrounding character, all space can thus be described as having a fundamentally ambient character. So what precisely is an ambient space, then? As I will argue in my presentation, ambient space is a sensory effect of spatiality when a space is experienced as being particularly surrounding: a ‘space effect...

  14. Automated Processing Workflow for Ambient Seismic Recordings

    Science.gov (United States)

    Girard, A. J.; Shragge, J.

    2017-12-01

    Structural imaging using body-wave energy present in ambient seismic data remains a challenging task, largely because these wave modes are commonly much weaker than surface wave energy. In a number of situations body-wave energy has been extracted successfully; however, (nearly) all successful body-wave extraction and imaging approaches have focused on cross-correlation processing. While this is useful for interferometric purposes, it can also lead to the inclusion of unwanted noise events that dominate the resulting stack, leaving body-wave energy overpowered by the coherent noise. Conversely, wave-equation imaging can be applied directly on non-correlated ambient data that has been preprocessed to mitigate unwanted energy (i.e., surface waves, burst-like and electromechanical noise) to enhance body-wave arrivals. Following this approach, though, requires a significant preprocessing effort on often Terabytes of ambient seismic data, which is expensive and requires automation to be a feasible approach. In this work we outline an automated processing workflow designed to optimize body wave energy from an ambient seismic data set acquired on a large-N array at a mine site near Lalor Lake, Manitoba, Canada. We show that processing ambient seismic data in the recording domain, rather than the cross-correlation domain, allows us to mitigate energy that is inappropriate for body-wave imaging. We first develop a method for window selection that automatically identifies and removes data contaminated by coherent high-energy bursts. We then apply time- and frequency-domain debursting techniques to mitigate the effects of remaining strong amplitude and/or monochromatic energy without severely degrading the overall waveforms. After each processing step we implement a QC check to investigate improvements in the convergence rates - and the emergence of reflection events - in the cross-correlation plus stack waveforms over hour-long windows. Overall, the QC analyses suggest that

  15. The sperm whale sonar: Monitoring and use in mitigation of anthropogenic noise effects in the marine environment

    International Nuclear Information System (INIS)

    Andre, Michel

    2009-01-01

    Noise pollution in the marine environment is an emerging but serious concern. Its implications are less well understood than other global threats and largely undetectable to everyone but the specialist. In addition, the assessment of the acoustic impact of artificial sounds in the sea is not a trivial task, certainly because there is a lack of information on how the marine organisms process and analyse sounds and how relevant these sounds are for the balance and development of the populations. Further, this possible acoustic impact not only concerns the hearing systems but may also affect other sensory or systemic levels and result equally lethal for the animal concerned. If we add that the negative consequences of a short or long term exposure to artificial sounds may not be immediately observed one can understood how challenging it is to obtain objective data allowing an efficient control of the introduction of anthropogenic sound in the sea. To answer some of these questions, the choice to investigate cetaceans and their adaptation to an aquatic environment is not fortuitous. Cetaceans, because of their optimum use of sound as an ad-hoc source of energy and their almost exclusive dependence on acoustic information, represent not only the best bio-indicator of the effects of noise pollution in the marine environment, but also a source of data to improve and develop human underwater acoustic technology. Here, we present how the characteristics and performance of the sperm whale mid-range biosonar can be used to develop a mitigation solution based on passive acoustics and ambient noise imaging to prevent negative interactions with human activities by monitoring cetacean movements in areas of interest, e.g. deep-sea observatories.

  16. The sperm whale sonar: Monitoring and use in mitigation of anthropogenic noise effects in the marine environment

    Energy Technology Data Exchange (ETDEWEB)

    Andre, Michel [Laboratory of Applied Bioacoustics, Technical University of Catalonia, Barcelona 08800 (Spain)], E-mail: michel.andre@upc.edu

    2009-04-11

    Noise pollution in the marine environment is an emerging but serious concern. Its implications are less well understood than other global threats and largely undetectable to everyone but the specialist. In addition, the assessment of the acoustic impact of artificial sounds in the sea is not a trivial task, certainly because there is a lack of information on how the marine organisms process and analyse sounds and how relevant these sounds are for the balance and development of the populations. Further, this possible acoustic impact not only concerns the hearing systems but may also affect other sensory or systemic levels and result equally lethal for the animal concerned. If we add that the negative consequences of a short or long term exposure to artificial sounds may not be immediately observed one can understood how challenging it is to obtain objective data allowing an efficient control of the introduction of anthropogenic sound in the sea. To answer some of these questions, the choice to investigate cetaceans and their adaptation to an aquatic environment is not fortuitous. Cetaceans, because of their optimum use of sound as an ad-hoc source of energy and their almost exclusive dependence on acoustic information, represent not only the best bio-indicator of the effects of noise pollution in the marine environment, but also a source of data to improve and develop human underwater acoustic technology. Here, we present how the characteristics and performance of the sperm whale mid-range biosonar can be used to develop a mitigation solution based on passive acoustics and ambient noise imaging to prevent negative interactions with human activities by monitoring cetacean movements in areas of interest, e.g. deep-sea observatories.

  17. Road traffic noise and incident myocardial infarction: a prospective cohort study

    DEFF Research Database (Denmark)

    Sørensen, Mette; Andersen, Zorana Jovanovic; Nordsborg, Rikke B

    2012-01-01

    Both road traffic noise and ambient air pollution have been associated with risk for ischemic heart disease, but only few inconsistent studies include both exposures.......Both road traffic noise and ambient air pollution have been associated with risk for ischemic heart disease, but only few inconsistent studies include both exposures....

  18. Risk mapping for sensitive species to underwater anthropogenic sound emissions: model development and validation in two Mediterranean areas.

    Science.gov (United States)

    Azzellino, A; Lanfredi, C; D'Amico, A; Pavan, G; Podestà, M; Haun, J

    2011-01-01

    Recent observations of cetacean mass strandings, coincident with anthropogenic sounds emissions, have raised concerns on the potential environmental impact of underwater noise. Cuvier's beaked whale (Ziphius cavirostris) was reported in all the cited stranding events. Within the NATO Marine Mammal Risk Mitigation project (MMRM), multiple interdisciplinary sea trials have been conducted in the Mediterranean Sea with the objective of developing tools and procedures to mitigate the impact of underwater sound emissions. During these cruises, visual observations, passive acoustic detections and environmental data were collected. The aim of this study was to evaluate "a priori" predictions of Cuvier's beaked whale presence in the Alboran Sea, using models developed in the Ligurian Sea that employ bathymetric and chlorophyll features as predictors. The accuracy of these predictions was found adequate and elements are given to account for the uncertainties associated to the use of models developed in areas different from their calibration site. Copyright © 2011 Elsevier Ltd. All rights reserved.

  19. Development of underwater laser cutting technique for steel and ...

    Indian Academy of Sciences (India)

    We have developed underwater cutting technique for 4.2 mm thick zircaloy pressure tubes and up to 6 mm thick steel using fibre-coupled 250 W average power pulsed Nd:YAG laser. This underwater cutting technique will be highly useful in various nuclear applications as well as in dismantling/repair of ship and pipe lines ...

  20. Visual-adaptation-mechanism based underwater object extraction

    Science.gov (United States)

    Chen, Zhe; Wang, Huibin; Xu, Lizhong; Shen, Jie

    2014-03-01

    Due to the major obstacles originating from the strong light absorption and scattering in a dynamic underwater environment, underwater optical information acquisition and processing suffer from effects such as limited range, non-uniform lighting, low contrast, and diminished colors, causing it to become the bottleneck for marine scientific research and projects. After studying and generalizing the underwater biological visual mechanism, we explore its advantages in light adaption which helps animals to precisely sense the underwater scene and recognize their prey or enemies. Then, aiming to transform the significant advantage of the visual adaptation mechanism into underwater computer vision tasks, a novel knowledge-based information weighting fusion model is established for underwater object extraction. With this bionic model, the dynamical adaptability is given to the underwater object extraction task, making them more robust to the variability of the optical properties in different environments. The capability of the proposed method to adapt to the underwater optical environments is shown, and its outperformance for the object extraction is demonstrated by comparison experiments.

  1. Self-localization for underwater inspection robot in reactor systems

    International Nuclear Information System (INIS)

    Kobayashi, Futoshi; Kojima, Fumio

    2007-01-01

    An underwater inspection robot has been needed for preventive maintenance in a nuclear power plant. This paper deals with a self-localization method for the underwater inspection robot. In this method, the position and the orientation of the robot are estimated by using the particle filter. For showing the effectiveness of the proposed method, an experiment with real robot is demonstrated. (author)

  2. WODA technical guidance on underwater sound from dredging

    NARCIS (Netherlands)

    Thomsen, F.; Borsani, F.; Clarke, D.; Jong, C. de; Wit, P. de; Goethals, F.; Holtkamp, M.; Martin, E.S.; Spadaro, P.; Raalte, G. van; Victor, G.Y.V.; Jensen, A.

    2016-01-01

    The World Organization of Dredging Associations (WODA) has identified underwater sound as an environmental issue that needs further consideration. A WODA Expert Group on Underwater Sound (WEGUS) prepared a guidance paper in 2013 on dredging sound, including a summary of potential impacts on aquatic

  3. The WODA guidance paper on underwater sound from dredging (abstract)

    NARCIS (Netherlands)

    Thomsen, F.; Borsani, F.; Clarke, D.; Jong, C.A.F. de; Witt, P. de; Holtkamp, M.; Goethals, F.; San Martin, E.; Spadaro, P.; Raalte, G. van; Jensen, A.

    2013-01-01

    The World Organisation of Dredging Associations (WODA) has identified underwater sound as an environmental issue that needs further consideration. A WODA Expert Group on Underwater Sound (WEGUS) was established to provide a guidance paper on dredging sound, impact on aquatic biota and advice on

  4. Development of underwater laser cutting technique for steel and ...

    Indian Academy of Sciences (India)

    Laser cutting; underwater laser cutting; fibre optic beam delivery; Nd:YAG laser; material processing; heat affected zone; microstructure. PACS Nos 42.62.Cf; 42.62.-b; 42.55.Rz; 42.81.Ai; 42.81.-i. 1. Introduction. Underwater laser cutting and welding has many applications in nuclear facilities and shiping industry and is a ...

  5. Underwater measurements and modeling of a sonic boom.

    Science.gov (United States)

    Desharnais, Francine; Chapman, David M F

    2002-01-01

    During a sea trial on the Scotian Shelf, acoustic signals from a sonic boom were recorded on 11 hydrophones of a vertical array. The array spanned the lower 50 m of the water column above a sand bank at 76 m water depth. The source of the sonic boom was deduced to be a Concorde supersonic airliner traveling at about Mach 2. The waterborne waveform was observed to decay as an evanescent wave below the sea surface, as expected. The calm weather (sea state 1) resulted in low ambient noise and low self-noise at the hydrophones, and good signal-to-noise ratio on the upper hydrophones; however, the decreased signal amplitude is more difficult to detect towards the lower part of the water column. The period of the observed waveform is of the order 0.23 s, corresponding to a peak frequency of about 3 Hz. The shape of the measured waveform differs noticeably from the theoretical N-shape waveform predicted with Sawyers' theory [J. Acoust. Soc. Am. 44, 523-524 (1968)]. A simple shallow-ocean geoacoustic model suggests that this effect may be caused in part by seismo-acoustic interaction of the infrasonic waves with the elastic sediments that form the seabed.

  6. Impact of noise and air pollution on pregnancy outcomes

    NARCIS (Netherlands)

    Gehring, Ulrike|info:eu-repo/dai/nl/304831344; Tamburic, Lillian; Sbihi, Hind; Davies, Hugh W.; Brauer, Michael

    2014-01-01

    Background: Motorized traffic is an important source of both air pollution and community noise. While there is growing evidence for an adverse effect of ambient air pollution on reproductive health, little is known about the association between traffic noise and pregnancy outcomes. Methods: We

  7. Capacitive Micromachined Ultrasonic Transducers (CMUTs for Underwater Imaging Applications

    Directory of Open Access Journals (Sweden)

    Jinlong Song

    2015-09-01

    Full Text Available A capacitive micromachined ultrasonic transducer structure for use in underwater imaging is designed, fabricated and tested in this paper. In this structure, a silicon dioxide insulation layer is inserted between the top electrodes and the vibration membrane to prevent ohmic contact. The capacitance-voltage (C-V characteristic curve shows that the transducer offers suitable levels of hysteresis and repeatability performance. The −6 dB center frequency is 540 kHz and the transducer has a bandwidth of 840 kHz for a relative bandwidth of 155%. Underwater pressure of 143.43 Pa is achieved 1 m away from the capacitive micromachined ultrasonic transducer under 20  excitation. Two-dimensional underwater ultrasonic imaging, which is able to prove that a rectangular object is present underwater, is achieved. The results presented here indicate that our work will be highly beneficial for the establishment of an underwater ultrasonic imaging system.

  8. Underwater Sensor Network Redeployment Algorithm Based on Wolf Search.

    Science.gov (United States)

    Jiang, Peng; Feng, Yang; Wu, Feng

    2016-10-21

    This study addresses the optimization of node redeployment coverage in underwater wireless sensor networks. Given that nodes could easily become invalid under a poor environment and the large scale of underwater wireless sensor networks, an underwater sensor network redeployment algorithm was developed based on wolf search. This study is to apply the wolf search algorithm combined with crowded degree control in the deployment of underwater wireless sensor networks. The proposed algorithm uses nodes to ensure coverage of the events, and it avoids the prematurity of the nodes. The algorithm has good coverage effects. In addition, considering that obstacles exist in the underwater environment, nodes are prevented from being invalid by imitating the mechanism of avoiding predators. Thus, the energy consumption of the network is reduced. Comparative analysis shows that the algorithm is simple and effective in wireless sensor network deployment. Compared with the optimized artificial fish swarm algorithm, the proposed algorithm exhibits advantages in network coverage, energy conservation, and obstacle avoidance.

  9. Design and implementation of an underwater sound recording device

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, Jayson J.; Myers, Joshua R.; Carlson, Thomas J.; Deng, Zhiqun; Rohrer, John S.; Caviggia, Kurt A.

    2011-09-19

    The purpose of this study was to design and build two versions of an underwater sound recording device. The device designed is referred to as the Underwater Sound Recorder (USR), which can be connected to one or two hydrophones or other underwater sound sensors. The URS contains a 26 dB preamplifier and a user selectable gain that permits additional amplification of input to the system from 26 dB to 46 dB. Signals within the frequency range up to 15 kHz may be recorded using the USR. Examples of USR applications are monitoring underwater processes that have the potential to create large pressure waves that could potentially harm fish or other aquatic life, such as underwater explosions or pile driving. Additional applications are recording sound generated by vessels or the vocalizations of some marine mammals, such as the calls from many species of whales.

  10. A man-made object detection for underwater TV

    Science.gov (United States)

    Cheng, Binbin; Wang, Wenwu; Chen, Yao

    2018-03-01

    It is a great challenging task to complete an automatic search of objects underwater. Usually the forward looking sonar is used to find the target, and then the initial identification of the target is completed by the side-scan sonar, and finally the confirmation of the target is accomplished by underwater TV. This paper presents an efficient method for automatic extraction of man-made sensitive targets in underwater TV. Firstly, the image of underwater TV is simplified with taking full advantage of the prior knowledge of the target and the background; then template matching technology is used for target detection; finally the target is confirmed by extracting parallel lines on the target contour. The algorithm is formulated for real-time execution on limited-memory commercial-of-the-shelf platforms and is capable of detection objects in underwater TV.

  11. Fouling in your own nest: vessel noise increases biofouling.

    Science.gov (United States)

    Stanley, Jenni A; Wilkens, Serena L; Jeffs, Andrew G

    2014-01-01

    Globally billions of dollars are spent each year on attempting to reduce marine biofouling on commercial vessels, largely because it results in higher fuel costs due to increased hydrodynamic drag. Biofouling has been long assumed to be primarily due to the availability of vacant space on the surface of the hull. Here, it is shown that the addition of the noise emitted through a vessel's hull in port increases the settlement and growth of biofouling organisms within four weeks of clean surfaces being placed in the sea. More than twice as many bryozoans, oysters, calcareous tube worms and barnacles settled and established on surfaces with vessel noise compared to those without. Likewise, individuals from three species grew significantly larger in size in the presence of vessel noise. The results demonstrate that vessel noise in port is promoting biofouling on hulls and that underwater sound plays a much wider ecological role in the marine environment than was previously considered possible.

  12. The future is 'ambient'

    Science.gov (United States)

    Lugmayr, Artur

    2006-02-01

    The research field of ambient media starts to spread rapidly and first applications for consumer homes are on the way. Ambient media is the logical continuation of research around media. Media has been evolving from old media (e.g. print media), to integrated presentation in one form (multimedia - or new media), to generating a synthetic world (virtual reality), to the natural environment is the user-interface (ambient media), and will be evolving towards real/synthetic undistinguishable media (bio-media or bio-multimedia). After the IT bubble was bursting, multimedia was lacking a vision of potential future scenarios and applications. Within this research paper the potentials, applications, and market available solutions of mobile ambient multimedia are studied. The different features of ambient mobile multimedia are manifold and include wearable computers, adaptive software, context awareness, ubiquitous computers, middleware, and wireless networks. The paper especially focuses on algorithms and methods that can be utilized to realize modern mobile ambient systems.

  13. Occupational Noise Exposure

    Science.gov (United States)

    ... Safety and Health Topics / Occupational Noise Exposure Occupational Noise Exposure This page requires that javascript be enabled ... interprets the signal as sound. x What is noise? Noise and vibration are both fluctuations in the ...

  14. Underwater welding using remote controlled robots. Development of remote underwater welding technology with a high power YAG laser

    International Nuclear Information System (INIS)

    Miwa, Yasuhiro; Sato, Syuuichi; Kojima, Toshio; Owaki, Katsura; Hirose, Naoya

    2002-01-01

    As components in nuclear power plant have been periodically carried out their inspection and repair to keep their integrity, on radioactive liquid wastes storage facility, because of difficulty on their inspection by human beings, some are remained without inspection, and even when capable of inspection, conversion from human works to remote operations is desired from a viewpoint of their operation efficiency upgrading. For response to these needs, some developments on a technology capable of carrying out inspection of their inside at underwater environment and repairing welding with YAG laser by means of remote operation, have been performed. Remote underwater inspection and repair technology is a combination technology of already applied underwater mobile technique (underwater inspection robot) with underwater YAG laser welding technique which is recently at actual using level. Therefore, this technology is composed of an inspection robot and a repair welding robot. And, testing results using the underwater inspection robot and welding test results using the underwater repair welding robot, were enough preferable to obtain forecasting applicable to actual apparatuses. This technology is especially effective for inspection and repair of inside of nuclear fuel cycle apparatuses and relatively high dose apparatuses, and can be thought to be applicable also to large capacity tanks, tanks dealing with harmful matters, underwater structures, and so on, in general industries. (G.K.)

  15. Water waves generated by underwater explosion

    CERN Document Server

    Mehaute, Bernard Le

    1996-01-01

    This is the first book on explosion-generated water waves. It presents the theoretical foundations and experimental results of the generation and propagation of impulsively generated waves resulting from underwater explosions. Many of the theories and concepts presented herein are applicable to other types of water waves, in particular, tsunamis and waves generated by the fall of a meteorite. Linear and nonlinear theories, as well as experimental calibrations, are presented for cases of deep and shallow water explosions. Propagation of transient waves on dissipative, nonuniform bathymetries to

  16. Hemispherical optical dome for underwater communication

    Science.gov (United States)

    Shiri, Ron S.; Lunde, Emily L.; Coronado, Patrick L.; Quijada, Manuel A.

    2017-08-01

    For many years, acoustic systems have been used as the primary method for underwater communication; however, the data transfer rate of such systems is low because sound propagates slowly through water. A higher throughput can be achieved using visible light to transmit data underwater. The first issue with this approach is that there is generally a large loss of the light signal due to scattering and absorption in water, even though there is an optimal wavelength for transmission in the blue or green wavelengths of the visible spectrum. The second issue is that a simple communication system, consisting only of a highly directional source/transmitter and small optical detector/receiver, has a very narrow field of view. The goal of this project is to improve an optical, underwater communication system by increasing the effective field of view of the receiving optics. To this end, we make two changes to the simple system: (1) An optical dome was added near the receiver. An array of lenses is placed radially on the surface of the dome, reminiscent of the compound eye of an insect. The lenses make the source and detector planes conjugate, and each lens adds a new region of the source plane to the instrument's total field of view. (2) The receiver was expanded to include multiple photodiodes. With these two changes, the receiver has much more tolerance to misalignments (in position and angle) of the transmitter. Two versions of the optical dome (with 6" and 8" diameters) were designed using PTC's Creo CAD software and modeled using Synopsys' CODE V optical design software. A series of these transparent hemispherical domes, with both design diameters, were manufactured using a 5-axis mill. The prototype was then retrofitted with lenses and compared with the computer-generated model to demonstrate the effectiveness of this solution. This work shows that the dome design improves the optical field of view of the underwater communication system considerably. Furthermore, with

  17. Underwater Sound Propagation from Marine Pile Driving.

    Science.gov (United States)

    Reyff, James A

    2016-01-01

    Pile driving occurs in a variety of nearshore environments that typically have very shallow-water depths. The propagation of pile-driving sound in water is complex, where sound is directly radiated from the pile as well as through the ground substrate. Piles driven in the ground near water bodies can produce considerable underwater sound energy. This paper presents examples of sound propagation through shallow-water environments. Some of these examples illustrate the substantial variation in sound amplitude over time that can be critical to understand when computing an acoustic-based safety zone for aquatic species.

  18. Radon dynamics in underwater thermal radon therapy

    International Nuclear Information System (INIS)

    Lettner, H.; Hofmann, W.; Winkler, R.; Rolle, R.; Foisner, W.

    1998-01-01

    At a facility for underwater thermal radon therapy in Bad Hofgastein, experiments were carried out with the aim of establishing radon in the air exhaled by the treated patients and of radon decay products on the skin of the patients. The time course of radon concentration in the exhaled air shows a maximum a few minutes after entering the bath, then the Rn concentration remains constant over the remaining time spent in the bath. Taking into account several simplifying assumptions, the average dose to the epidermis from radon daughters is about 50 μGy. (A.K.)

  19. Navigation System Fault Diagnosis for Underwater Vehicle

    DEFF Research Database (Denmark)

    Falkenberg, Thomas; Gregersen, Rene Tavs; Blanke, Mogens

    2014-01-01

    This paper demonstrates fault diagnosis on unmanned underwater vehicles (UUV) based on analysis of structure of the nonlinear dynamics. Residuals are generated using dierent approaches in structural analysis followed by statistical change detection. Hypothesis testing thresholds are made signal...... based to cope with non-ideal properties seen in real data. Detection of both sensor and thruster failures are demonstrated. Isolation is performed using the residual signature of detected faults and the change detection algorithm is used to assess severity of faults by estimating their magnitude...

  20. Adaptive Target Tracking for Underwater Maneuvering Targets.

    Science.gov (United States)

    1979-12-01

    concenetrate on the bearings-only approach. In this method the Observer monitors his bearing to the Source, over a period of time. Usually the Observer must...developed in [ 5] was earlier applied with much success to tracking maneuvering air targets. This approach will now be applied in the underwater environment...April 1977. [11] A. H. Jazwinski, Stochastic Processes and Filtering Theory, Academic Press, New York, 1970. [12] D. H. Halliday, and R. Resnick, Physics, John Wiley & Sons, Inc., New York, 1966. hI