Underground or aboveground storage tanks - A critical decision

International Nuclear Information System (INIS)

Rizzo, J.A.

1992-01-01

With the 1988 promulgation of the comprehensive Resource Conservation and Recovery Act (RCRA) regulations for underground storage of petroleum and hazardous substances, many existing underground storage tank (UST) owners have been considering making the move to aboveground storage. While on the surface, this may appear to be the cure-all to avoiding the underground leakage dilemma, there are many other new and different issues to consider with aboveground storage. The greatest misconception is that by storing materials above ground, there is no risk of subsurface environmental problems. It should be noted that with the aboveground storage tank (AGST) systems, there is still considerable risk of environmental contamination, either by the failure of onground tank bottoms or the spillage of product onto the ground surface where it subsequently finds its way to the ground water. In addition, there are added safety concerns that must be addressed. The greatest interest in AGSTs comes from managers with small volumes of used oil, fresh oil, solvents, chemicals, or heating oil. Dealing with small capacity tanks is not so different than large bulk storage - and, in fact, it lends itself to more options, such as portable storage, tank within tank configurations and inside installations. So what are the other specific areas of concern besides environmental to be addressed when making the decision between underground and aboveground tanks? The primary issues that will be addressed in this presentation are: (1) safety; (2) product losses; (3) cost comparison of USTs vs AGSTs; (4) space availability/accessibility; (5) precipitation handling; (6) aesthetics and security; (7) pending and existing regulations

Permanent Closure of the TAN-664 Underground Storage Tank

Energy Technology Data Exchange (ETDEWEB)

Bradley K. Griffith

2011-12-01

This closure package documents the site assessment and permanent closure of the TAN-664 gasoline underground storage tank in accordance with the regulatory requirements established in 40 CFR 280.71, 'Technical Standards and Corrective Action Requirements for Owners and Operators of Underground Storage Tanks: Out-of-Service UST Systems and Closure.'

Underground storage

Energy Technology Data Exchange (ETDEWEB)

1965-06-10

A procedure is described for making an underground storage cavity in a soluble formation. Two holes are drilled, and fluid is pumped into the first hole. This fluid is a non-solute for the formation material. Then pressure is applied to the fluid until the formation is fractured in the direction of the second hole. More non-solute fluid is injected to complete the fracture between the 2 holes. A solute fluid is then circulated between the 2 holes, which results in removal of that part of the formation next to the fracture and the forming of a chamber.

Reflection Phenomena in Underground Pumped Storage Reservoirs

Directory of Open Access Journals (Sweden)

Elena Pummer

2018-04-01

Full Text Available Energy storage through hydropower leads to free surface water waves in the connected reservoirs. The reason for this is the movement of water between reservoirs at different elevations, which is necessary for electrical energy storage. Currently, the expansion of renewable energies requires the development of fast and flexible energy storage systems, of which classical pumped storage plants are the only technically proven and cost-effective technology and are the most used. Instead of classical pumped storage plants, where reservoirs are located on the surface, underground pumped storage plants with subsurface reservoirs could be an alternative. They are independent of topography and have a low surface area requirement. This can be a great advantage for energy storage expansion in case of environmental issues, residents’ concerns and an unusable terrain surface. However, the reservoirs of underground pumped storage plants differ in design from classical ones for stability and space reasons. The hydraulic design is essential to ensure their satisfactory hydraulic performance. The paper presents a hybrid model study, which is defined here as a combination of physical and numerical modelling to use the advantages and to compensate for the disadvantages of the respective methods. It shows the analysis of waves in ventilated underground reservoir systems with a great length to height ratio, considering new operational aspects from energy supply systems with a great percentage of renewable energies. The multifaceted and narrow design of the reservoirs leads to complex free surface flows; for example, undular and breaking bores arise. The results show excessive wave heights through wave reflections, caused by the impermeable reservoir boundaries. Hence, their knowledge is essential for a successful operational and constructive design of the reservoirs.

State Certification of Underground Storage Tanks

National Research Council Canada - National Science Library

Granetto, Paul

1998-01-01

.... The audit was performed in response to a Senate Armed Services Committee inquiry about whether state environmental regulatory agencies would be able to certify that DoD underground storage tanks...

Leak detection for underground storage tanks

International Nuclear Information System (INIS)

Durgin, P.B.; Young, T.M.

1993-01-01

This symposium was held in New Orleans, Louisiana on January 29, 1992. The purpose of this conference was to provide a forum for exchange of state-of-the-art information on leak detection for underground storage tanks that leaked fuel. A widespread concern was protection of groundwater supplies from these leaking tanks. In some cases, the papers report on research that was conducted two or three years ago but has never been adequately directed to the underground storage tank leak-detection audience. In other cases, the papers report on the latest leak-detection research. The symposium was divided into four sessions that were entitled: Internal Monitoring; External Monitoring; Regulations and Standards; and Site and Risk Evaluation. Individual papers have been cataloged separately for inclusion in the appropriate data bases

Numerical modeling of underground storage system for natural gas

Science.gov (United States)

Ding, J.; Wang, S.

2017-12-01

Natural gas is an important type of base-load energy, and its supply needs to be adjusted according to different demands in different seasons. For example, since natural gas is increasingly used to replace coal for winter heating, the demand for natural gas in winter is much higher than that in other seasons. As storage systems are the essential tools for balancing seasonal supply and demand, the design and simulation of natural gas storage systems form an important research direction. In this study, a large-scale underground storage system for natural gas is simulated based on theoretical analysis and finite element modeling.It is proven that the problem of axi-symmetric Darcy porous flow of ideal gas is governed by the Boussinesq equation. In terms of the exact solution to the Boussinesq equation, the basic operating characteristics of the underground storage system is analyzed, and it is demonstrated that the propagation distance of the pore pressure is proportional to the 1/4 power of the mass flow rate and to the 1/2 power of the propagation time. This quantitative relationship can be used to guide the overall design of natural gas underground storage systems.In order to fully capture the two-way coupling between pore pressure and elastic matrix deformation, a poro-elastic finite element model for natural gas storage is developed. Based on the numerical model, the dynamic processes of gas injection, storage and extraction are simulated, and the corresponding time-dependent surface deformations are obtained. The modeling results not only provide a theoretical basis for real-time monitoring for the operating status of the underground storage system through surface deformation measurements, but also demonstrate that a year-round balance can be achieved through periodic gas injection and extraction.This work is supported by the CAS "100 talents" Program and the National Natural Science Foundation of China (41371090).

Leaking Underground Storage Tank Sites in Iowa

Data.gov (United States)

Iowa State University GIS Support and Research Facility — Leaking Underground Storage Tank (LUST) sites where petroleum contamination has been found. There may be more than one LUST site per UST site.

LPG fuel

International Nuclear Information System (INIS)

Dagnas, F.X.; Jeuland, N.; Fouquet, J.P.; Lauraire, S.; Coroller, P.

2005-01-01

LPG fuel has become frequently used through a distribution network with 2 000 service stations over the French territory. LPG fuel ranks number 3 world-wide given that it can be used on individual vehicles, professional fleets, or public transport. What is the environmental benefit of LPG fuel? What is the technology used for these engines? What is the current regulation? Government commitment and dedication on support to promote LPG fuel? Car makers projects? Actions to favour the use of LPG fuel? This article gathers 5 presentations about this topic given at the gas conference

Permanent Closure of MFC Biodiesel Underground Storage Tank 99ANL00013

Energy Technology Data Exchange (ETDEWEB)

Kerry L. Nisson

2012-10-01

This closure package documents the site assessment and permanent closure of the Materials and Fuels Complex biodiesel underground storage tank 99ANL00013 in accordance with the regulatory requirements established in 40 CFR 280.71, “Technical Standards and Corrective Action Requirements for Owners and Operators of Underground Storage Tanks: Out-of-Service UST Systems and Closure.”

Geological Feasibility of Underground Oil Storage in Jintan Salt Mine of China

Directory of Open Access Journals (Sweden)

Xilin Shi

2017-01-01

Full Text Available A number of large underground oil storage spaces will be constructed in deep salt mines in China in the coming years. According to the general geological survey, the first salt cavern oil storage base of China is planned to be built in Jintan salt mine. In this research, the geological feasibility of the salt mine for oil storage is identified in detail as follows. (1 The characteristics of regional structure, strata sediment, and impermeable layer distribution of Jintan salt mine were evaluated and analyzed. (2 The tightness of cap rock was evaluated in reviews of macroscopic geology and microscopic measuring. (3 According to the geological characteristics of Jintan salt mine, the specific targeted formation for building underground oil storage was chosen, and the sealing of nonsalt interlayers was evaluated. (4 Based on the sonar measuring results of the salt caverns, the characteristics of solution mining salt caverns were analyzed. In addition, the preferred way of underground oil storage construction was determined. (5 Finally, the results of closed well observation in solution mining salt caverns were assessed. The research results indicated that Jintan salt mine has the basic geological conditions for building large-scale underground oil storage.

Risk assessment of liquefied petroleum gas (LPG storage tanks in the process industries using the Bowtie technique

Directory of Open Access Journals (Sweden)

Mostafa Mirzaei aliabadi

2016-09-01

Full Text Available Introduction: LPG storage tanks contain of large volumes of flammable and pressurized gases. Release of these fluids can lead to disastrous accidents such BLEVE, fiery explosion. Therefore, identifying the causes, consequences, probabilities and scenarios of accidents using Bowtie technique, that is combination of Fault Tree Analyses (FTA and Event Tree Analyses (ETA, is imperative and the purpose of this study. Methods: The hazards of the mentioned in Tehran Refinery LPG tanks were identified by Fault Tree Analyses and the consequences of the top event were predicted by Event Tree Analyses. Then probabilities of the events were calculated and the accident route, from causes phase to consequences phase, was drawn by Bowtie diagram. Results: In total, 21 events and 11 minimal cut sets with their occurrence probabilities and importance measure were determined at the left side of the Bowtie diagram. Also 9 consequences and scenarios of the top event were determined at the right side of the diagram. The occurrence probability of the top event (LPG release of spherical tanks was calculated 3.45×10-2. Conclusion: All factors involved in the occurrence of accidents and their consequences are showed in the Bowtie diagram. According to the obtained data, failure of cathodic protection systems and instrumentation, and overflow of tanks are included as important defects of the LPG tanks. Due to the high probability of the consequences, preventing systems such as cooling systems and Fire stop systems are required for installing in the studied unit to reduce the consequences of accidents.

Thermal Response Analyses of Spherical LPG Storage Tank

Energy Technology Data Exchange (ETDEWEB)

Chen, Hsijen.; Lin, Mannhsing.; Chao, Fuyuan

1999-02-01

Liquefied petroleum gas (LPG) is a very important fuel and chemical feed stock as well; however, the hydrocarbon has been involved in many major fires and explosions. One of these accidents is boiling-liquid, expanding-vapor explosion (BLEVE). It is a phenomenon that results from the sudden release form confinement of a liquid at a temperature above its atmospheric-pressure boiling point. The sudden decrease in pressure results in the explosive vaporization of a fraction of the liquid and a cloud of vapor and mist with the accompanying blast effects. Most BLEVEs involve flammable liquids, and most BELEVE releases are ignited by a surrounding fire and result in a fireball. The primary objective of this paper is to develop a computer model in order to determine the thermal response of a spherical LPG tank involved in fire engulfment accidents. The assessment of the safety spacing between tanks was also discussed. (author)

Underground storage tank program

International Nuclear Information System (INIS)

Lewis, M.W.

1994-01-01

Underground storage tanks, UST'S, have become a major component of the Louisville District's Environmental Support Program. The District's Geotechnical and Environmental Engineering Branch has spear-headed an innovative effort to streamline the time, effort and expense for removal, replacement, upgrade and associated cleanup of USTs at military and civil work installations. This program, called Yank-A-Tank, creates generic state-wide contracts for removal, remediation, installation and upgrade of storage tanks for which individual delivery orders are written under the basic contract. The idea is to create a ''JOC type'' contract containing all the components of work necessary to remove, reinstall or upgrade an underground or above ground tank. The contract documents contain a set of generic specifications and unit price books in addition to the standard ''boiler plate'' information. Each contract requires conformance to the specific regulations for the state in which it is issued. The contractor's bid consists of a bid factor which in the multiplier used with the prices in the unit price book. The solicitation is issued as a Request for Proposal (RPP) which allows the government to select a contractor based on technical qualification an well as bid factor. Once the basic contract is awarded individual delivery orders addressing specific areas of work are scoped, negotiated and awarded an modifications to the original contract. The delivery orders utilize the prepriced components and the contractor's factor to determine the value of the work

Regulatory approaches to hydrocarbon contamination from underground storage tanks

International Nuclear Information System (INIS)

Daugherty, S.J.

1991-01-01

Action or lack of action by the appropriate regulatory agency is often the most important factor in determining remedial action or closure requirements for hydrocarbon contaminated sites. This paper reports that the diversity of regulatory criteria is well known statewide and well documented nationally. In California, the diversity of approaches is due to: that very lack of a clear understanding of the true impact of hydrocarbon contamination: lack of state or federal standards for soil cleanup, and state water quality objectives that are not always achievable; vagueness in the underground storage tank law; and the number and diversity of agencies enforcing the underground storage tank regulations

Natural convection and vapor loss during underground waste storage

International Nuclear Information System (INIS)

Plys, M.G.; Epstein, M.; Turner, D.

1996-01-01

Natural convection and vapor loss from underground waste storage tanks is examined here. Stability criteria are provided for the onset of natural convection flow within the headspace of a tank, and between tanks and the environment. The flowrate is quantified and used to predict vapor losses during storage

Correction: Large-scale electricity storage utilizing reversible solid oxide cells combined with underground storage of CO2 and CH4

DEFF Research Database (Denmark)

Jensen, Søren Højgaard; Graves, Christopher R.; Mogensen, Mogens Bjerg

2017-01-01

Correction for ‘Large-scale electricity storage utilizing reversible solid oxide cells combined with underground storage of CO2 and CH4’ by S. H. Jensen et al., Energy Environ. Sci., 2015, 8, 2471–2479.......Correction for ‘Large-scale electricity storage utilizing reversible solid oxide cells combined with underground storage of CO2 and CH4’ by S. H. Jensen et al., Energy Environ. Sci., 2015, 8, 2471–2479....

Decision analysis of Hanford underground storage tank waste retrieval systems

International Nuclear Information System (INIS)

Merkhofer, M.W.; Bitz, D.A.; Berry, D.L.; Jardine, L.J.

1994-05-01

A decision analysis approach has been proposed for planning the retrieval of hazardous, radioactive, and mixed wastes from underground storage tanks. This paper describes the proposed approach and illustrates its application to the single-shell storage tanks (SSTs) at Hanford, Washington

Salt creep design consideration for underground nuclear waste storage

International Nuclear Information System (INIS)

Li, W.T.; Wu, C.L.; Antonas, N.J.

1983-01-01

This paper summarizes the creep consideration in the design of nuclear waste storage facilities in salt, describes the non-linear analysis method for evaluating the design adequacy, and presents computational results for the current storage design. The application of rock mechanics instrumentation to assure the appropriateness of the design is discussed. It also describes the design evolution of such a facility, starting from the conceptual design, through the preliminary design, to the detailed design stage. The empirical design method, laboratory tests and numerical analyses, and the underground in situ tests have been incorporated in the design process to assure the stability of the underground openings, retrievability of waste during the operation phase and encapsulation of waste after decommissioning

The underground retrievable storage (URS) high-level waste management concept

International Nuclear Information System (INIS)

Ramspott, L.D.

1991-01-01

This papers presents the concept of long-term underground retrievable storage (URS) of spent reactor fuel in unsaturated rock. Emplacement would be incremental and the system is planned to be experimental and flexible. The rationale for retrievability is examined, and a technical basis for 300-year retrievability is presented. Maximum isolation is the rationale for underground as opposed to surface storage. Although the potential repository site at Yucca Mountain Nevada would be suitable for a URS, alternate sites are discussed. The technical issues involved in licensing a URS for 300 years are simpler than licensing a 10,000 year repository. 16 refs

Regulated underground storage tanks

International Nuclear Information System (INIS)

1992-06-01

This guidance package is designed to assist DOE Field operations by providing thorough guidance on the underground storage tank (UST) regulations. [40 CFR 280]. The guidance uses tables, flowcharts, and checklists to provide a ''roadmap'' for DOE staff who are responsible for supervising UST operations. This package is tailored to address the issues facing DOE facilities. DOE staff should use this guidance as: An overview of the regulations for UST installation and operation; a comprehensive step-by-step guidance for the process of owning and operating an UST, from installation to closure; and a quick, ready-reference guide for any specific topic concerning UST ownership or operation

An Underground Storage Tank Integrated Demonstration report

International Nuclear Information System (INIS)

Quadrel, M.J.; Hunter, V.L.; Young, J.K.; Lini, D.C.; Goldberg, C.

1993-04-01

The Waste Characterization Data and Technology Development Needs Assessment provides direct support to the Underground Storage Tank Integrated Demonstration (UST-ID). Key users of the study's products may also include individuals and programs within the US Department of Energy (DOE) Office of Technology Development (EM-50), the Office of Waste Operations (EM-30), and the Office of Environmental Restoration (EM-40). The goal of this work is to provide the UST-ID with a procedure for allocating funds across competing characterization technologies in a timely and defensible manner. It resulted in three primary products: 1. It organizes and summarizes information on underground storage tank characterization data needs. 2. It describes current technology development activity related to each need and flags areas where technology development may be beneficial. 3. It presents a decision process, with supporting software, for evaluating, prioritizing, and integrating possible technology development funding packages. The data presented in this document can be readily updated as the needs of the Waste Operations and Environmental Restoration programs mature and as new and promising technology development options emerge

The LPG-fuel industry

International Nuclear Information System (INIS)

Anon.

1996-01-01

The LPG-fuel industry comprises several professionals from various domains such as assembly shops for vehicles transformation, materials manufacturers for public distribution stations and companies which produce and commercialize the LPG-fuel. This paper summarizes the administrative and technical liabilities of these professionals, with the technical qualification required, the regulations concerning the official approval of transformation kits and pressure tanks. The French network of public distribution stations for LPG-fuel is shared between five independent dispensers with their own economic policy which represents about 700 LPG-stations. However, the safety regulations concerning LPG-fuels considerably limit the installation of LPG facilities in urban areas. A cost-benefit comparison between LPG and other liquid fuels is given in inset and takes into account the transformation costs of the vehicle. (J.S.)

Reducing drinking water supply chemical contamination: risks from underground storage tanks.

Science.gov (United States)

Enander, Richard T; Hanumara, R Choudary; Kobayashi, Hisanori; Gagnon, Ronald N; Park, Eugene; Vallot, Christopher; Genovesi, Richard

2012-12-01

Drinking water supplies are at risk of contamination from a variety of physical, chemical, and biological sources. Ranked among these threats are hazardous material releases from leaking or improperly managed underground storage tanks located at municipal, commercial, and industrial facilities. To reduce human health and environmental risks associated with the subsurface storage of hazardous materials, government agencies have taken a variety of legislative and regulatory actions--which date back more than 25 years and include the establishment of rigorous equipment/technology/operational requirements and facility-by-facility inspection and enforcement programs. Given a history of more than 470,000 underground storage tank releases nationwide, the U.S. Environmental Protection Agency continues to report that 7,300 new leaks were found in federal fiscal year 2008, while nearly 103,000 old leaks remain to be cleaned up. In this article, we report on an alternate evidence-based intervention approach for reducing potential releases from the storage of petroleum products (gasoline, diesel, kerosene, heating/fuel oil, and waste oil) in underground tanks at commercial facilities located in Rhode Island. The objective of this study was to evaluate whether a new regulatory model can be used as a cost-effective alternative to traditional facility-by-facility inspection and enforcement programs for underground storage tanks. We conclude that the alternative model, using an emphasis on technical assistance tools, can produce measurable improvements in compliance performance, is a cost-effective adjunct to traditional facility-by-facility inspection and enforcement programs, and has the potential to allow regulatory agencies to decrease their frequency of inspections among low risk facilities without sacrificing compliance performance or increasing public health risks. © 2012 Society for Risk Analysis.

Underground storage of nuclear waste

International Nuclear Information System (INIS)

Russell, J.E.

1977-06-01

The objective of the National Waste Terminal Storage (NWTS) Program is to provide facilities in various deep geologic formations at multiple locations in the United States which will safely dispose of commerical radioactive waste. The NWTS Program is being administered for the Energy Research and Development Administration (ERDA) by the Office of Waste Isolation (OWI), Union Carbide Corporation, Nuclear Division. OWI manages projects that will lead to the location, construction, and operation of repositories, including all surface and underground engineering and facility design projects and technical support projects. 7 refs., 5 figs

Underground storage of nuclear waste

Energy Technology Data Exchange (ETDEWEB)

Russell, J E

1977-12-01

The objective of the National Waste Terminal Storage (NWTS) Program is to provide facilities in various deep geologic formations at multiple locations in the United States which will safely dispose of commercial radioactive waste. The NWTS Program is being administered for the Energy Research and Development Administration (ERDA) by the Office of Waste Isolation (OWI), Union Carbide Corporation, Nuclear Division. OWI manages projects that will lead to the location, construction, and operation of repositories, including all surface and underground engineering and facility design projects and technical support projects.

Aims, organization and activities of the consortium for underground storage

International Nuclear Information System (INIS)

Stucky, G.

1977-01-01

The consortium of Swiss authorities interested in underground storage (the petroleum oil and gas industries, for fuel storage; the nuclear industry for radioactive waste disposal), was initiated in 1972. The author outlines the motives behind the formation of the consortium and outlines its structure and objectives. The envisaged projects are outlined. (F.Q.)

Underground storage. Study of radwaste storage in deep geological formations: environmental protection

International Nuclear Information System (INIS)

Hoorelbeke, J.M.

1993-01-01

The purpose of the Agence nationale pour la gestion des dechets radioactifs (Andra) is to monitor the management methods and storage of radioactive waste produced in France. The agency has this undertaken a vast study program for the evaluation of the management conditions of long-life radwaste, which cannot be stored indefinitely in shallow-ground repositories. Underground laboratories are investigating the feasibility of a possible solution which is to store radwaste in a deep geological layer. However, there will be no decision on this type of storage before the year 2006. 7 figs

Integral Safety Assessment of Underground Storage of CO2 in Barendrecht, the Netherlands

International Nuclear Information System (INIS)

Vijgen, L.; Nitert, M.; Buijtendijk, B.; Van Dalen, A.

2009-10-01

The DCMR Environmental Protection Agency Rijnmond in the Netherlands conducted an Integral Safety Assessment of Underground Storage of CO2 in Barendrecht, the Netherlands, in cooperation with the involved safety and supervision authorities. The following aspects of the entire storage project and its safety issues have been examined: the compressor station in Pernis; the underground pipes between the compressor station and the injection locations; and the injection locations Barendrecht-Ziedewij and Barendrecht. [nl

LPG world supply and demand

International Nuclear Information System (INIS)

Holmes, Ch.

2008-01-01

Over the course of this decade, the global LPG market has moved from being tight, where supply barely exceeded non-price sensitive demand, to the current market situation where supply growth has outstripped demand growth to such an extent that current fundamentals suggest that considerable length will prevail in the market over the near term. As is the case for many other energy commodity markets, the LPG industry has experienced a considerable transformation over the last five years with many new LPG supply projects coming on-stream and demand growth in many developing markets slowing in response to higher energy prices. The near term challenge for LPG producers will be securing outlets for output as the market becomes increasingly oversupplied. With expanding LPG supply and a worldwide tightness in the naphtha market, it is expected that petrochemical consumers will favor relatively low priced LPG over naphtha and the resulting increase in LPG cracking rates will go some way to reducing the expected supply surplus. However, the timing of several new LPG supply projects and the start-up of LPG-based petrochemical plants in the Middle-East are expected to impact global LPG trade and pricing over the next few years. Thus, at this point in time, the global LPG market has a high degree of uncertainty with questions remaining over the impact of high energy (and LPG) prices on traditional and developing market demand, the timing of new supply projects and the combined effect of these two factors on international LPG prices. World LPG production has been rising in nearly every region of the world over the last few years and totaled about 229 million tons in 2007, which is some 30 million tons per year higher than in 2000. The exception is North America which accounts for the largest share of global LPG supply at about 24% but production there has remained relatively flat in recent years. Strong LPG production growth in the Middle-East which contributed to about 19% of

Pursing other deep pockets: California's underground storage tank cleanup fund and insurance policies

International Nuclear Information System (INIS)

Almanza, P.R.

1995-01-01

When faced with a potentially very expensive environmental cleanup, most companies and individuals try to do the only sensible thing, which is to find out if anyone else will pay the bill. This presentation will outline two avenues that may provide a substantial financial contribution to environmental cleanups: (a) California's Underground Storage Tank Cleanup Fund and (b) insurance policies. The Underground Storage Tank Cleanup Fund was established in 1989 to help eligible owners and operators of petroleum underground storage tanks (USTs) to: (a) get reimbursed for costs of unauthorized releases of petroleum from USTs; (b) get reimbursed for damages awarded to third parties as a result of unauthorized releases of petroleum from USTs; and (c) meet federal and state requirements that the UST owner and/or operator be able to pay for cleanup costs and damages to third parties caused by unauthorized releases of petroleum

Design and operation problems related to water curtain system for underground water-sealed oil storage caverns

Directory of Open Access Journals (Sweden)

Zhongkui Li

2016-10-01

Full Text Available The underground water-sealed storage technique is critically important and generally accepted for the national energy strategy in China. Although several small underground water-sealed oil storage caverns have been built in China since the 1970s, there is still a lack of experience for large-volume underground storage in complicated geological conditions. The current design concept of water curtain system and the technical instruction for system operation have limitations in maintaining the stability of surrounding rock mass during the construction of the main storage caverns, as well as the long-term stability. Although several large-scale underground oil storage projects are under construction at present in China, the design concepts and construction methods, especially for the water curtain system, are mainly based on the ideal porosity medium flow theory and the experiences gained from the similar projects overseas. The storage projects currently constructed in China have the specific features such as huge scale, large depth, multiple-level arrangement, high seepage pressure, complicated geological conditions, and high in situ stresses, which are the challenging issues for the stability of the storage caverns. Based on years' experiences obtained from the first large-scale (millions of cubic meters underground water-sealed oil storage project in China, some design and operation problems related to water curtain system during project construction are discussed. The drawbacks and merits of the water curtain system are also presented. As an example, the conventional concept of “filling joints with water” is widely used in many cases, as a basic concept for the design of the water curtain system, but it is immature. In this paper, the advantages and disadvantages of the conventional concept are pointed out, with respect to the long-term stability as well as the safety of construction of storage caverns. Finally, new concepts and principles

The analysis of risks at LPG depots: a tool for decision makers

Energy Technology Data Exchange (ETDEWEB)

Anon.

1993-10-01

At the Tokyo congress of the World LPG Forum, Mr Patrick Mayras, Technical Director at Butagaz, presented a study on the probability of the occurrence of a major accident which this company has undertaken with Cremer Warner on its storage and filling site in Montereau, together with the key prevention principles which have resulted from this study and which have been applied to all their installations. The study shows that the probability of a BLEVE is 1 in a thousand million years per sphere or, for the 60 storage sites belonging to Butagaz, that the probability of a BLEVE in its installations is 1 every 16 million years. If every company in the profession had this level of standards on an international scale, the probability of a BLEVE occurring in the world would be, again according to Butagaz calculations, of the order of 1 every 100.000 years or, at a really conservative estimate, of the order of 1 every 10.000 years (based on: one storage site for 10.000 t sold/year). This report was received with a great deal of interest in Tokyo and it is certain that this probability-based approach will constitute hence-forth a reference both on a national and an international scale. As Mr Mayras underlined at the end of his presentation, although a zero risk does not exist, there is a socially acceptable risk which is used implicitly by governmental authorities for certain human or industrial activities for certain human or industrial activities which have an accident occurrence probability which is much higher than that run by LPG storage sites. Conversely, the determinist and calculated approach applied in France presents a high cost to society due to the freezing of all land around the sites. The probability-based approach, which can be systematized to all LPG professionals, could, therefore, allow for a relaxation of the constraints weighing on the environment of storage sites and could place LPG on an equal footing with other types of energy. (Abstract Truncated)

ENERGY EFFICIENCY, ENERGY SAVING POTENTIAL AND ENVIRONMENTAL IMPACT RESEARCH OF LPG CARRIER REFRIGERATION SYSTEM

Directory of Open Access Journals (Sweden)

V. О. Bedrosov

2016-12-01

Full Text Available Nowadays energy efficiency improvement and global warming are issues of current interest because of the natural resources depletion and extreme climate change. Thus, the problem of formation of strict regulations regarding emissions into the air arises. This paper presents the study of cascade refrigeration system for re-condensing of associated petroleum gas during sea transportation for LPG carrier. The structural optimization has been performed. LPG gas carriers with 266 000 m3 ethane capacity require 15 MW cascade refrigeration system for re-condensing if the temperature in the coastal LPG storage is -70°C, and the temperature for transported Ethan is maintained at  -75°C. For current storage conditions the required system cooling capacity is only 1,078 MW intended for the heat gain rejection from the environment during Ethane transportation. The replacement of ozone-depleting refrigerant R22 to alternative agents: R407C, R404A, R402A, R717, R290, R1270 was estimated. The results of analysis have shown that the proposed improvements can be used to optimize the LPG carrier cascade refrigeration system

The LPG industry road-map

International Nuclear Information System (INIS)

Anon.

2008-01-01

This paper presents the challenges of LPG industry in contributing to the economic and social growth in Europe for the coming decades: due to its specific characteristics - both as a product and an industry - LPG can make a meaningful contribution to meeting the Europe's 3 objectives of sustainability, security of supply and competitiveness both now and in the future. LPG industry wants to reinforce its role in meeting some of the world's most pressing challenges: reducing human impact on the environment, protecting human health, and ensuring a secure energy supply. Doubling LPG's contribution to the energy mix in Europe will significantly boost the positive impact of LPG on its users and society as a whole. The LPG industry can play also an important role in the indoor applications sector. Industry estimates suggest that this sector could grow by 55% between 2001 and 2030. However, to transform this potential into a reality, a series of conditions, notably the improvement of existing applications, support in terms of R and D for the development of new applications and an enhanced degree of cooperation with innovative renewable energies, need to be met. As such, it is vital to put a structure in place to promote cooperation and exchanges between public authorities and relevant industrial actors. There are three key type of initiative to be taken: encouraging consumers to switch from conventional fuels to clean alternatives such as LPG, stimulating the modification (retrofitting) of existing vehicles from petrol-fuelled to LPG-fuelled, and encouraging car-makers to place new vehicles powered by LPG, mono-fuel, bi-fuel (LPG/petrol, LPG/biofuel) or hybrid (LPG/electric) on the market. Taken as a whole, the measures outlined above would yield numerous benefits, not only in terms of protecting the environment and human health, but also providing a valuable contribution to rural development in Europe. Expanding the role of LPG in industry throughout the EU yields the

Underground storage of natural gas in Italy

International Nuclear Information System (INIS)

Henking, E.

1992-01-01

After first relating the importance of natural gas storage to the viability of Italian industrial activities, this paper discusses the geo-physical nature of different types of underground cavities which can be used for natural gas storage. These include depleted petroleum and natural gas reservoirs, aquifers and abandoned mines. Attention is given to the geologic characteristics and physical characteristics such as porosity, permeability and pressure that determine the suitability of any given storage area, and to the techniques used to resolve problems relative to partially depleted reservoirs, e.g., the presence of oil, water and salt. A review is made of Italy's main storage facilities. This review identifies the various types of storage techniques, major equipment, operating and maintenance practices. A look is then given at Italy's plans for the development of new facilities to meet rising demand expected to reach 80 billion cubic meters/year by the turn of the century. The operating activities of the two leading participants, SNAM and AGIP, in Italy's natural gas industry are highlighted. Specific problems which contribute to the high operating costs of natural gas storage are identified and a review is made of national normatives governing gas storage. The report comes complete with a glossary of the relative terminology and units of measure

The significance of LPG in Turkish vehicular transportation: liquefied petroleum gases (LPG) in fueled systems

Energy Technology Data Exchange (ETDEWEB)

Balat, Mustafa [Besikduzu, Trabzon (Turkey)

2005-04-15

Liquefied petroleum gases (LPG) are in widespread use in homes, industry and agriculture. Among the many uses of these gases are heating and refrigeration, as a supplement for natural gas, as fuel for industrial equipment and mobile homes, in the manufacture of ethylene, and as a solvent. Worldwide LPG production is limited to about 10% of total gasoline and diesel fuel consumption and is used to a great extent for domestic and industrial purposes. Since LPG burns cleaner with less carbon build-up and oil contamination, engine wear is reduced and the life of some components, such as rings and bearings, is much longer than with gasoline. The high octane of LPG also minimizes wear from engine knock. The rapid development of LPG technology, including ease of vehicular conversion and estimations of increased LPG availability, suggest LPG will soon be recognized as a premium automotive fuel. (Author)

Polymers for subterranean containment barriers for underground storage tanks (USTs)

International Nuclear Information System (INIS)

Heiser, J.H.; Colombo, P.; Clinton, J.

1992-12-01

The US Department of Energy (DOE) set up the Underground Storage Tank Integrated Demonstration Program (USTID) to demonstrate technologies for the retrieval and treatment of tank waste, and closure of underground storage tanks (USTs). There are more than 250 underground storage tanks throughout the DOE complex. These tanks contain a wide variety of wastes including high level, low level, transuranic, mixed and hazardous wastes. Many of the tanks have performed beyond the designed lifetime resulting in leakage and contamination of the local geologic media and groundwater. To mitigate this problem it has been proposed that an interim subterranean containment barrier be placed around the tanks. This would minimize or prevent future contamination of soil and groundwater in the event that further tank leakages occur before or during remediation. Use of interim subterranean barriers can also provide sufficient time to evaluate and select appropriate remediation alternatives. The DOE Hanford site was chosen as the demonstration site for containment barrier technologies. A panel of experts for the USTID was convened in February, 1992, to identify technologies for placement of subterranean barriers. The selection was based on the ability of candidate grouts to withstand high radiation doses, high temperatures and aggressive tank waste leachates. The group identified and ranked nine grouting technologies that have potential to place vertical barriers and five for horizontal barriers around the tank. The panel also endorsed placement technologies that require minimal excavation of soil surrounding the tanks

Advancing the US Department of Energy's Technologies through the Underground Storage Tank: Integrated Demonstration Program

International Nuclear Information System (INIS)

Gates, T.E.

1993-01-01

The principal objective of the Underground Storage Tank -- Integrated Demonstration Program is the demonstration and continued development of technologies suitable for the remediation of waste stored in underground storage tanks. The Underground Storage Tank Integrated Demonstration Program is the most complex of the integrated demonstration programs established under the management of the Office of Technology Development. The Program has the following five participating sites: Oak Ridge, Idaho, Fernald, Savannah River, and Hanford. Activities included within the Underground Storage Tank -- Integrated Demonstration are (1) characterizating radioactive and hazardous waste constituents, (2) determining the need and methodology for improving the stability of the waste form, (3) determining the performance requirements, (4) demonstrating barrier performance by instrumented field tests, natural analog studies, and modeling, (5) determining the need and method for destroying and stabilizing hazardous waste constituents, (6) developing and evaluating methods for retrieving, processing (pretreatment and treatment), and storing the waste on an interim basis, and (7) defining and evaluating waste packages, transportation options, and ultimate closure techniques including site restoration. The eventual objective is the transfer of new technologies as a system to full-scale remediation at the US Department of Energy complexes and sites in the private sector

Radioactive waste storage facility and underground disposal method for radioactive wastes using the facility

International Nuclear Information System (INIS)

Endo, Yoshihiro.

1997-01-01

A sealed container storage chamber is formed in underground rocks. A container storage pool is formed on the inner bottom of the sealed vessel storage chamber. A heat exchanger for cooling water and a recycling pump are disposed on an operation floor of the sealed vessel storage chamber. Radioactive wastes sealed vessels in which radioactive wastes are sealed are transferred from the ground to the sealed vessel storage chamber through a sealed vessel transferring shaft, and immersed in cooling water stored in the vessel storage pool. When after heat of the radioactive wastes is removed by the cooling water, the cooling water in the vessel storage pool is sucked up to the ground surface. After dismantling equipments, bentonite-type fillers are filled in the inside of the sealed vessel storage chamber, sealed vessel transferring shaft, air supplying shaft and air exhaustion shaft, and the radioactive waste-sealed vessels can be subjected stably to into underground disposal. (I.N.)

STORAGE AND RECOVERY OF SECONDARY WASTE COMING FROM MUNICIPAL WASTE INCINERATION PLANTS IN UNDERGROUND MINE

Directory of Open Access Journals (Sweden)

Waldemar Korzeniowski

2016-09-01

Full Text Available Regarding current and planned development of municipal waste incineration plants in Poland there is an important problem of the generated secondary waste management. The experience of West European countries in mining shows that waste can be stored successfully in the underground mines, but especially in salt mines. In Poland there is a possibility to set up the underground storage facility in the Salt Mine “Kłodawa”. The mine today is capable to locate over 3 million cubic meters and in the future it can increase significantly. Two techniques are proposed: 1 – storage of packaged waste, 2 – waste recovery as selfsolidifying paste with mining technology for rooms backfilling. Assuming the processing capacity of the storage facility as 100 000 Mg of waste per year, “Kłodawa” mine will be able to accept around 25 % of currently generated waste coming from the municipal waste incineration plants and the current volume of the storage space is sufficient for more than 20 years. Underground storage and waste recovery in mining techniques are beneficial for the economy and environment.

Underground Storage Tank Integrated Demonstration (UST-ID)

International Nuclear Information System (INIS)

1994-02-01

The DOE complex currently has 332 underground storage tanks (USTs) that have been used to process and store radioactive and chemical mixed waste generated from weapon materials production. Very little of the over 100 million gallons of high-level and low-level radioactive liquid waste has been treated and disposed of in final form. Two waste storage tank design types are prevalent across the DOE complex: single-shell wall and double-shell wall designs. They are made of stainless steel, concrete, and concrete with carbon steel liners, and their capacities vary from 5000 gallons (19 m 3 ) to 10 6 gallons (3785 m 3 ). The tanks have an overburden layer of soil ranging from a few feet to tens of feet. Responding to the need for remediation of tank waste, driven by Federal Facility Compliance Agreements (FFCAs) at all participating sites, the Underground Storage Tank Integrated Demonstration (UST-ID) Program was created by the US DOE Office of Technology Development in February 1991. Its mission is to focus the development, testing, and evaluation of remediation technologies within a system architecture to characterize, retrieve, treat to concentrate, and dispose of radioactive waste stored in USTs at DOE facilities. The ultimate goal is to provide safe and cost-effective solutions that are acceptable to the public and the regulators. The UST-ID has focused on five DOE locations: the Hanford Site, which is the host site, in Richland, Washington; the Fernald Site in Fernald, Ohio; the Idaho National Engineering Laboratory near Idaho Falls, Idaho; the Oak Ridge Reservation in Oak Ridge, Tennessee, and the Savannah River Site in Savannah River, South Carolina

100-N Area underground storage tank closures

Energy Technology Data Exchange (ETDEWEB)

Rowley, C.A.

1993-08-01

This report describes the removal/characterization actions concerning underground storage tanks (UST) at the 100-N Area. Included are 105-N-LFT, 182-N-1-DT, 182-N-2-DT, 182-N-3-DT, 100-N-SS-27, and 100-N-SS-28. The text of this report gives a summary of remedial activities. In addition, correspondence relating to UST closures can be found in Appendix B. Appendix C contains copies of Unusual Occurrence Reports, and validated sampling data results comprise Appendix D.

100-N Area underground storage tank closures

International Nuclear Information System (INIS)

Rowley, C.A.

1993-01-01

This report describes the removal/characterization actions concerning underground storage tanks (UST) at the 100-N Area. Included are 105-N-LFT, 182-N-1-DT, 182-N-2-DT, 182-N-3-DT, 100-N-SS-27, and 100-N-SS-28. The text of this report gives a summary of remedial activities. In addition, correspondence relating to UST closures can be found in Appendix B. Appendix C contains copies of Unusual Occurrence Reports, and validated sampling data results comprise Appendix D

AT on Buried LPG Tanks Over 13 m3: An Innovative and Practical Solution

Science.gov (United States)

Di Fratta, Crescenzo; Ferraro, Antonio; Tscheliesnig, Peter; Lackner, Gerald; Correggia, Vincenzo; Altamura, Nicola

In Italy, since 2005, techniques based on Acoustic Emission have been introduced for testing of underground LPG tanks up to 13 m3, according to the European standard EN 12818:2004. The testing procedure for these tanks plans to install one or more pairs of sensors inside the "dome" suited for the access to the valves and fittings of the tank, directly on the accessible metal shell. This methodology is not applicable for the underground LPG buried tanks, where it is necessary to install a larger number of AE sensors, in order to cover at 100% the whole tank shell, even at very deep positions. Already in 2004, the European standard EN 12820 (Appendix C - Informative)give the possibility to use Acoustic Emission testing of LPG underground or buried tanks with a capacity exceeding 13 m3, but no technique was specified for the application. In 2008, TÜV AUSTRIA ITALIA - BLU SOLUTIONS srl - Italian company of TÜV AUSTRIA Group - has developed a technique to get access at tank shell, where tank capacity is greater than 13 m3 and its' diameter greater than 3,5 m. This methodology was fully in comply with the provisions of the European Standard EN 12819:2010, becoming an innovative solution widely appreciated and is used in Italy since this time. Currently, large companies and petrochemical plants, at the occurrence of the tank's requalification, have engaged TÜV AUSTRIA ITALIA - BLU SOLUTIONS to install such permanent predispositions, which allow access to the tank shell - test object - with diameters from 4 to 8 m. Through this access, you can install the AE sensors needed to cover at 100% the tank surface and then to perform AE test. In an economic crisis period, this technique is proving a valid and practically applicable answer, in order to reduce inspection costs and downtime by offering a technically advanced solution (AT), increasing the safety of the involved operators, protecting natural resources and the environment.

VOLUMETRIC LEAK DETECTION IN LARGE UNDERGROUND STORAGE TANKS - VOLUME I

Science.gov (United States)

A set of experiments was conducted to determine whether volumetric leak detection system presently used to test underground storage tanks (USTs) up to 38,000 L (10,000 gal) in capacity could meet EPA's regulatory standards for tank tightness and automatic tank gauging systems whe...

High temperature underground thermal energy storage system for solar energy

Science.gov (United States)

Collins, R. E.

1980-01-01

The activities feasibility of high temperature underground thermal storage of energy was investigated. Results indicate that salt cavern storage of hot oil is both technically and economically feasible as a method of storing huge quantities of heat at relatively low cost. One particular system identified utilizes a gravel filled cavern leached within a salt dome. Thermal losses are shown to be less than one percent of cyclically transferred heat. A system like this having a 40 MW sub t transfer rate capability and over eight hours of storage capacity is shown to cost about $13.50 per KWh sub t.

Underground storage tanks containing hazardous chemicals

International Nuclear Information System (INIS)

Wise, R.F.; Starr, J.W.; Maresca, J.W. Jr.; Hillger, R.W.; Tafuri, A.N.

1991-01-01

The regulations issued by the United States Environmental Protection Agency in 1988 require, with several exceptions, that underground storage tank systems containing petroleum fuels and hazardous chemicals be routinely tested for releases. This paper summarizes the release detection regulations for tank systems containing chemicals and gives a preliminary assessment of the approaches to release detection currently being used. To make this assessment, detailed discussions were conducted with providers and manufacturers of leak detection equipment and testing services, owners or operators of different types of chemical storage tank systems, and state and local regulators. While these discussions were limited to a small percentage of each type of organization, certain observations are sufficiently distinctive and important that they are reported for further investigation and evaluation. To make it clearer why certain approaches are being used, this paper also summarizes the types of chemicals being stored, the effectiveness of several leak detection testing systems, and the number and characteristics of the tank systems being used to store these products

Arrangement for underground storage of materials of every kind

International Nuclear Information System (INIS)

Marek, O.; Seisenbacher, H.; Toth, L.

1982-01-01

Construction of a spheroidal tank, made of two sheets of concrete, used for underground storage. Space between inner and outer sheet is filled with a vibration absorbing material. The bottom of the outer sheet is made of material with lower rigidness, which allows the line of fault in cases of tectonic motions to slide off. (J.K.) [de

Bi-fuel System - Gasoline/LPG in A Used 4-Stroke Motorcycle - Fuel Injection Type

Science.gov (United States)

Suthisripok, Tongchit; Phusakol, Nachaphat; Sawetkittirut, Nuttapol

2017-10-01

Bi-fuel-Gasoline/LPG system has been effectively and efficiently used in gasoline vehicles with less pollutants emission. The motorcycle tested was a used Honda AirBlade i110 - fuel injection type. A 3-litre LPG storage tank, an electronic fuel control unit, a 1-mm LPG injector and a regulator were securely installed. The converted motorcycle can be started with either gasoline or LPG. The safety relief valve was set below 48 kPa and over 110 kPa. The motorcycle was tuned at the relative rich air-fuel ratio (λ) of 0.85-0.90 to attain the best power output. From dynamometer tests over the speed range of 65-100 km/h, the average power output when fuelling LPG was 5.16 hp; dropped 3.9% from the use of gasoline91. The average LPG consumption rate from the city road test at the average speed of 60 km/h was 40.1 km/l, about 17.7% more. This corresponded to lower LPG’s energy density of about 16.2%. In emission, the CO and HC concentrations were 44.4% and 26.5% lower. Once a standard gas equipment set with ECU and LPG injector were securely installed and the engine was properly tuned up to suit LPG’s characteristics, the converted bi-fuel motorcycle offers efficiently, safely and economically performance with environmental friendly emission.

Instability risk analysis and risk assessment system establishment of underground storage caverns in bedded salt rock

Science.gov (United States)

Jing, Wenjun; Zhao, Yan

2018-02-01

Stability is an important part of geotechnical engineering research. The operating experiences of underground storage caverns in salt rock all around the world show that the stability of the caverns is the key problem of safe operation. Currently, the combination of theoretical analysis and numerical simulation are the mainly adopts method of reserve stability analysis. This paper introduces the concept of risk into the stability analysis of underground geotechnical structure, and studies the instability of underground storage cavern in salt rock from the perspective of risk analysis. Firstly, the definition and classification of cavern instability risk is proposed, and the damage mechanism is analyzed from the mechanical angle. Then the main stability evaluating indicators of cavern instability risk are proposed, and an evaluation method of cavern instability risk is put forward. Finally, the established cavern instability risk assessment system is applied to the analysis and prediction of cavern instability risk after 30 years of operation in a proposed storage cavern group in the Huai’an salt mine. This research can provide a useful theoretical base for the safe operation and management of underground storage caverns in salt rock.

Underground storage tank management plan

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-09-01

The Underground Storage Tank (UST) Management Program at the Oak Ridge Y-12 Plant was established to locate UST systems in operation at the facility, to ensure that all operating UST systems are free of leaks, and to establish a program for the removal of unnecessary UST systems and upgrade of UST systems that continue to be needed. The program implements an integrated approach to the management of UST systems, with each system evaluated against the same requirements and regulations. A common approach is employed, in accordance with Tennessee Department of Environment and Conservation (TDEC) regulations and guidance, when corrective action is mandated. This Management Plan outlines the compliance issues that must be addressed by the UST Management Program, reviews the current UST inventory and compliance approach, and presents the status and planned activities associated with each UST system. The UST Management Plan provides guidance for implementing TDEC regulations and guidelines for petroleum UST systems. (There are no underground radioactive waste UST systems located at Y-12.) The plan is divided into four major sections: (1) regulatory requirements, (2) implementation requirements, (3) Y-12 Plant UST Program inventory sites, and (4) UST waste management practices. These sections describe in detail the applicable regulatory drivers, the UST sites addressed under the Management Program, and the procedures and guidance used for compliance with applicable regulations.

Underground storage tank management plan

International Nuclear Information System (INIS)

1994-09-01

The Underground Storage Tank (UST) Management Program at the Oak Ridge Y-12 Plant was established to locate UST systems in operation at the facility, to ensure that all operating UST systems are free of leaks, and to establish a program for the removal of unnecessary UST systems and upgrade of UST systems that continue to be needed. The program implements an integrated approach to the management of UST systems, with each system evaluated against the same requirements and regulations. A common approach is employed, in accordance with Tennessee Department of Environment and Conservation (TDEC) regulations and guidance, when corrective action is mandated. This Management Plan outlines the compliance issues that must be addressed by the UST Management Program, reviews the current UST inventory and compliance approach, and presents the status and planned activities associated with each UST system. The UST Management Plan provides guidance for implementing TDEC regulations and guidelines for petroleum UST systems. (There are no underground radioactive waste UST systems located at Y-12.) The plan is divided into four major sections: (1) regulatory requirements, (2) implementation requirements, (3) Y-12 Plant UST Program inventory sites, and (4) UST waste management practices. These sections describe in detail the applicable regulatory drivers, the UST sites addressed under the Management Program, and the procedures and guidance used for compliance with applicable regulations

Regulatory analysis of the Underground Storage Tank-Integrated Demonstration Program

International Nuclear Information System (INIS)

Smith, E.H.

1992-01-01

The Underground Storage Tank-Integrated Demonstration (UST-ID) Program has been developed to identify, demonstrate, test, and evaluate technologies that will provide alternatives to the current underground storage tank remediation program. The UST-ID Program is a national program that consists of five participating US Department of Energy (DOE) sites where technologies can be developed an ultimately demonstrated. Once these technologies are demonstrated, the UST-ID Program will transfer the developed technology system to industry (governmental or industrial) for application or back to Research and Development for further evaluation and modification, as necessary. In order to ensure that the UST-ID Program proceeds without interruption, it will be necessary to identify regulatory requirements along with associated permitting and notification requirements early in the technology development process. This document serves as a baseline for identifying certain federal and state regulatory requirements that may impact the UST-ID Program and the demonstration of any identified technologies

Japan and LPG

International Nuclear Information System (INIS)

Anon.

1993-01-01

About 20 million metric tonnes of Liquefied Petroleum Gases (LPG) are consumed each year in Japan, of which 14,5 million metric tonnes are imported from Saudi Arabia and United Arab Emirates. This paper presents LPG industry in Japan and gives informations on the present status: supply and demand, imports, market, distribution

Closure Report for Corrective Action Unit 135: Areas 25 Underground Storage Tanks, Nevada Test Site, Nevada

Energy Technology Data Exchange (ETDEWEB)

D. H. Cox

2001-06-01

Corrective Action Unit (CAU) 135, Area 25 Underground Storage Tanks, was closed in accordance with the approved Corrective Action Plan (DOE/NV, 2000). CAU 135 consists of three Corrective Action Sites (CAS). Two of these CAS's were identified in the Corrective Action Investigation Data Quality Objective meeting as being improperly identified as underground storage tanks. CAS 25-02-03 identified as the Deluge Valve Pit was actually an underground electrical vault and CAS 25-02-10 identified as an Underground Storage Tank was actually a former above ground storage tank filled with demineralized water. Both of these CAS's are recommended for a no further action closure. CAS 25-02-01 the Underground Storage Tanks commonly referred to as the Engine Maintenance Assembly and Disassembly Waste Holdup Tanks and Vault was closed by decontaminating the vault structure and conducting a radiological verification survey to document compliance with the Nevada Test Site unrestricted use release criteria. The Area 25 Underground Storage Tanks, (CAS 25-02-01), referred to as the Engine Maintenance, Assembly, and Disassembly (E-MAD) Waste Holdup Tanks and Vault, were used to receive liquid waste from all of the radioactive and cell service area drains at the E-MAD Facility. Based on the results of the Corrective Action Investigation conducted in June 1999, discussed in ''The Corrective Action Investigation Plan for Corrective Action Unit 135: Area 25 Underground Storage Tanks, Nevada Test Site, Nevada'' (DOE/NV, 199a), one sample from the radiological survey of the concrete vault interior exceeded radionuclide preliminary action levels. The analytes from the sediment samples exceeded the preliminary action levels for polychlorinated biphenyls, Resource Conservation and Recovery Act metals, total petroleum hydrocarbons as diesel-range organics, and radionuclides. The CAU 135 closure activities consisted of scabbling radiological ''hot spots

Lower Colorado River GRP Underground Storage Tank Sites (Closed), Nevada, 2012, Nevada Division of Environmental Protection Bureau of Corrective Actions

Data.gov (United States)

U.S. Environmental Protection Agency — The BCA layers are derived from a database for Federally Regulated Underground Storage Tanks (UST) and a database for Remediation and Leaking Underground Storage...

Lower Colorado River GRP Underground Storage Tank Sites (Open), Nevada, 2012, Nevada Division of Environmental Protection Bureau of Corrective Actions

Data.gov (United States)

U.S. Environmental Protection Agency — The BCA layers are derived from a database for Federally Regulated Underground Storage Tanks (UST) and a database for Remediation and Leaking Underground Storage...

Underground storage with floating cover. An overview; Erdbeckenspeicher mit schwimmender Abdeckung. Eine Uebersicht

Energy Technology Data Exchange (ETDEWEB)

Heller, A.; Maureschat, G.; Duer, K. [Technical Univ. of Denmark, Lyngby (Denmark). Dept. of Buildings and Energy

1998-12-31

A number of underground stores have been developed in recent years in Denmark. The development has been subsidised with funds of `Development program renewable energy` launched by the Danish Ministry for Environment and Energy. First experience reports on underground storage show that more emphasis must be put on the development of storage sealing and cover construction. Hence research works currently focuses on the investigation of liner material and further development of floating cover constructions. The target is the development of underground storage using solar energy for heating that can compete with conventional heating systems technically and economically. (orig.) [Deutsch] In Daenemark hat man in den letzten Jahren eine Reihe von Erdbeckenspeichern entwickelt. Die Entwicklung wird mit Mitteln aus dem `Entwicklungsprogramm Erneuerbare Energie` vom daenischen Umwelt- und Energieministerium finanziell gefoerdert. Die ersten Erfahrungen mit Erdbeckenspeichern haben gezeigt, dass ein verstaerkter Einsatz bei der Entwicklung von Abdichtungen des Speichers und von Deckelkonstruktionen gefordert ist. Deshalb wird in Daenemark aktuell mit der Untersuchung von Linermaterialien und der Weiterentwicklung von schwimmenden Deckelkonstruktionen gearbeitet. Das Ziel dieser Arbeit ist es, Erdbeckenspeicher zu entwickeln, die die Ausnutzung von Sonnenenergie zur Waermeversorgung im Vergleich mit herkoemmlicher Waermeversorgung sowohl technisch als auch oekonomisch konkurrenzfaehig macht. (orig.)

Large-Scale Wireless Temperature Monitoring System for Liquefied Petroleum Gas Storage Tanks

Directory of Open Access Journals (Sweden)

Guangwen Fan

2015-09-01

Full Text Available Temperature distribution is a critical indicator of the health condition for Liquefied Petroleum Gas (LPG storage tanks. In this paper, we present a large-scale wireless temperature monitoring system to evaluate the safety of LPG storage tanks. The system includes wireless sensors networks, high temperature fiber-optic sensors, and monitoring software. Finally, a case study on real-world LPG storage tanks proves the feasibility of the system. The unique features of wireless transmission, automatic data acquisition and management, local and remote access make the developed system a good alternative for temperature monitoring of LPG storage tanks in practical applications.

Large-Scale Wireless Temperature Monitoring System for Liquefied Petroleum Gas Storage Tanks.

Science.gov (United States)

Fan, Guangwen; Shen, Yu; Hao, Xiaowei; Yuan, Zongming; Zhou, Zhi

2015-09-18

Temperature distribution is a critical indicator of the health condition for Liquefied Petroleum Gas (LPG) storage tanks. In this paper, we present a large-scale wireless temperature monitoring system to evaluate the safety of LPG storage tanks. The system includes wireless sensors networks, high temperature fiber-optic sensors, and monitoring software. Finally, a case study on real-world LPG storage tanks proves the feasibility of the system. The unique features of wireless transmission, automatic data acquisition and management, local and remote access make the developed system a good alternative for temperature monitoring of LPG storage tanks in practical applications.

Plan of deep underground construction for investigations on high-level radioactive waste storage

International Nuclear Information System (INIS)

Mayanovskij, M.S.

1996-01-01

The program of studies of the Japanese PNC corporation on construction of deep underground storage for high-level radioactive wastes is presented. The program is intended for 20 years. The total construction costs equal about 20 billion yen. The total cost of the project is equal to 60 billion yen. The underground part is planned to reach 1000 m depth

Environmental Protection: Improved Inspections and Enforcement Would Ensure Safer Underground Storage Tanks

National Research Council Canada - National Science Library

Stephenson, John

2001-01-01

...) Underground Storage Tank (UST) program. 1 The program is relevant to today's hearing because studies have shown that tanks that leak hazardous substances, such as methyl tertiary butyl ether (MTBE...

The Italian LPG market

International Nuclear Information System (INIS)

Anon.

1998-01-01

As happened in other European countries, the Italian LPG consumption market narrowed in 1997 for climatic reasons. Still, with some 3,5 million tones it is the first LPG market in Europe thanks to automotive LPG which represents some 1,2 million tones, for 1,4 million tones for the bulk and 760, 000 tonnes for bottled products. Another characteristic of the Italian market: demand is slightly lowering in the North while increasing in the South and in the large islands. (author)

The electrostatic properties of Fiber-Reinforced-Plastics double wall underground storage gasoline tanks

International Nuclear Information System (INIS)

Li, Yipeng; Liu, Quanzhen; Meng, He; Sun, Lifu; Zhang, Yunpeng

2013-01-01

At present Fiber Reinforced Plastics (FRP) double wall underground storage gasoline tanks are wildly used. An FRP product with a resistance of more than 10 11 Ω is a static non-conductor, so it is difficult for the static electricity in the FRP product to decay into the earth. In this paper an experimental system was built to simulate an automobile gasoline filling station. Some electrostatic parameters of the gasoline, including volume charge density, were tested when gasoline was unloaded into a FRP double wall underground storage tank. Measurements were taken to make sure the volume charge density in the oil-outlet was similar to the volume charge density in the tank. In most cases the volume charge density of the gasoline was more than 22.7 μC m −3 , which is likely to cause electrostatic discharge in FRP double wall underground storage gasoline tanks. On the other hand, it would be hard to ignite the vapor by electrostatic discharge since the vapor pressure in the tanks is over the explosion limit. But when the tank is repaired or re-used, the operators must pay attention to the static electricity and some measurements should be taken to avoid electrostatic accident. Besides the relaxation time of charge in the FRP double wall gasoline storage tanks should be longer.

Microbial Life in an Underground Gas Storage Reservoir

Science.gov (United States)

Bombach, Petra; van Almsick, Tobias; Richnow, Hans H.; Zenner, Matthias; Krüger, Martin

2015-04-01

While underground gas storage is technically well established for decades, the presence and activity of microorganisms in underground gas reservoirs have still hardly been explored today. Microbial life in underground gas reservoirs is controlled by moderate to high temperatures, elevated pressures, the availability of essential inorganic nutrients, and the availability of appropriate chemical energy sources. Microbial activity may affect the geochemical conditions and the gas composition in an underground reservoir by selective removal of anorganic and organic components from the stored gas and the formation water as well as by generation of metabolic products. From an economic point of view, microbial activities can lead to a loss of stored gas accompanied by a pressure decline in the reservoir, damage of technical equipment by biocorrosion, clogging processes through precipitates and biomass accumulation, and reservoir souring due to a deterioration of the gas quality. We present here results from molecular and cultivation-based methods to characterize microbial communities inhabiting a porous rock gas storage reservoir located in Southern Germany. Four reservoir water samples were obtained from three different geological horizons characterized by an ambient reservoir temperature of about 45 °C and an ambient reservoir pressure of about 92 bar at the time of sampling. A complementary water sample was taken at a water production well completed in a respective horizon but located outside the gas storage reservoir. Microbial community analysis by Illumina Sequencing of bacterial and archaeal 16S rRNA genes indicated the presence of phylogenetically diverse microbial communities of high compositional heterogeneity. In three out of four samples originating from the reservoir, the majority of bacterial sequences affiliated with members of the genera Eubacterium, Acetobacterium and Sporobacterium within Clostridiales, known for their fermenting capabilities. In

What is LPG-fuel?

International Nuclear Information System (INIS)

Anon.

1996-01-01

The LPG-f (Liquefied Petroleum Gas) fuels are better known by the public users for their domestic applications (cooking, sanitary water heating and building heating). This paper describes the chemical composition and properties of LPG fuels together with their environmental advantages (low S content and NOx and CO emissions, no particulates) with respect to other fossil fuels. Advantages for vehicle engines (cleaner combustion, no dilution of the engine lubricant) and passengers (reduction of noise pollution) are summarized. The worldwide production/consumption of LPG is given. (J.S.)

A research on the excavation and maintenance of underground energy storage

Energy Technology Data Exchange (ETDEWEB)

Shin, Hee-Soon; Chung, So-Keul; Ryu, Chang-Ha [Korea Institute of Geology Mining and Materials, Taejon (KR)] (and others)

1999-12-01

CAES which is called as a compressed air energy storage was firstly developed at Huntorf, Gen-nan in 1978. The capacity of that system was 290MW, and it can be treated as a first commercial power plant. CAES has a lot of merits, such as saving the unit price of power generation, averaging the peak demand, improvement of maintenance, enlarging the benefit of dynamic use. According to the literature survey, the unlined rock cavern should be proposed to be a reasonable storing style as a method of compressed air storage in Korea. In this study, the most important techniques were evaluated through the investigation of the foreign construction case studies, especially on the unlined rock caverns in hard rock mass. We decided the hill of the Korea Institute of Geology, Mining and Materials as CAES site. If we construct the underground spaces in this site, the demand for electricity nearby Taejon should be considered. So we could determine the capacity of the power plant as a 350MW. This capacity needs a underground space of 200,000, and we can conclude 4 parallel tunnels 550m deep from the surface through the numerical studies. Design parameters were achieved from 300m depth boring job and image processing job. Moreover the techniques for determination of joint characteristics from the images could be obtained. Blasting pattern was designed on the underground spaces, and automatic gas control system and thermomechanical characteristics on caverns were also studied. And finally the following research items could be proposed for future researches. (1) Establishment of criteria for selection of optimal tunnel type. (2) Evaluation of water tightening ability. (3) Investigation of Lining type. (4) Development of techniques for site investigation in deep underground project. (5) Evaluation of construction techniques for underground space and shaft. (6) Investigation of long-term maintenance for pressured tunnel. (author). 14 refs.

Office building with an underground storage system. Operational experiences after one year; Buerogebaeude mit Erdspeicher. Betriebserfahrungen nach einem Jahr

Energy Technology Data Exchange (ETDEWEB)

Braun, Dorothee; Wehrli, Stefan [Basler und Hofmann AG, Zuerich (Switzerland)

2011-07-01

Self-sufficient heating and cooling - that was the principle of Basler paragraph Hofmann AG (Zuerich, Switzerland) and Stuecheli Architects (Zuerich, Switzerland) in the planning and constructing of a new office building in the Canton of Zuerich. For the first time an underground storage system was implemented in a commercial building. This underground storage refuels the solar energy in summer and supplies heating energy in winter. The office building was settled in in September, 2010. The pioneering project now delivers first empirical values with the underground storage system. These empirical values show: The concept comes up, but needs time.

Inherent security benefits of underground dry storage of nuclear materials

International Nuclear Information System (INIS)

Moore, R.D.; Zahn, T.

1997-07-01

This paper, augmented by color slides and handouts, will examine the inherent security benefits of underground dry storage of nuclear materials. Specific items to be presented include: the successful implementation of this type of storage configuration at Argonne National Laboratory - West; facility design concepts with security as a primary consideration; physical barriers achieved by container design; detection, assessment, and monitoring capabilities; and open-quotes self protectionclose quotes strategies. This is a report on the security features of such a facility. The technical operational aspects of the facility are beyond the scope of this paper

Underground storage tank soft waste dislodging and conveyance

International Nuclear Information System (INIS)

Wellner, A.F.S.

1993-01-01

The primary objective of this task is to demonstrate potential technical solutions and to acquire engineering data and information on the retrieval technologies applicable for use in retrieving waste from underground storage tanks. This task focuses on soft waste dislodging and conveyance technologies that would be used in conjunction with a manipulator-based retrieval system. This retrieval task focuses on Hanford single-shell tanks, but the results may also have applications to other waste retrieval problems. This work is part of the U.S. Department of Energy's (DOE's) Office of Technology Development, sponsored by the DOE's Richland Operations Office under the Underground Storage Tanks Integrated Demonstration (USTID) program. This task is one element of the whole waste dislodging and conveyance system in the USTID. The tank wastes contain both hazardous and radioactive constituents. This task focuses on the processes for dislodging and retrieving soft wastes, mainly sludge. Sludge consists primarily of heavy-metal, iron, and aluminum precipitates. Sludges vary greatly in their physical properties and may contain pockets of liquid. Sludges have been described as varying in consistency from thick slurry to sticky clay and as sandy with hard chunks of material. The waste is believed to have adhesive and cohesive properties. The quantitative physical properties of the wastes have yet to be measured. The waste simulants used in the testing program emulate the physical properties of the tank waste

Lower Colorado River GRP Leaking Underground Storage Tank Sites (Closed), Nevada, 2012, Nevada Division of Environmental Protection Bureau of Corrective Actions

Data.gov (United States)

U.S. Environmental Protection Agency — The BCA layers are derived from a database for Federally Regulated Underground Storage Tanks (UST) and a database for Remediation and Leaking Underground Storage...

Lower Colorado River GRP Leaking Underground Storage Tank Sites (Open), Nevada, 2012, Nevada Division of Environmental Protection Bureau of Corrective Actions

Data.gov (United States)

U.S. Environmental Protection Agency — The BCA layers are derived from a database for Federally Regulated Underground Storage Tanks (UST) and a database for Remediation and Leaking Underground Storage...

Optimization of basic parameters of cyclic operation of underground gas storages

Directory of Open Access Journals (Sweden)

Віктор Олександрович Заєць

2015-04-01

Full Text Available The problem of optimization of process parameters of cyclic operation of underground gas storages in gas mode is determined in the article. The target function is defined, expressing necessary capacity of compressor station for gas injection in the storage. Its minimization will find the necessary technological parameters, such as flow and reservoir pressure change over time. Limitations and target function are reduced to a linear form. Solution of problems is made by the simplex method

Modeling the performance of coated LPG tanks engulfed in fires

Energy Technology Data Exchange (ETDEWEB)

Landucci, Gabriele [CONPRICI - Dipartimento di Ingegneria Chimica, Chimica Industriale e Scienza dei Materiali, Universita di Pisa, via Diotisalvi n.2, 56126 Pisa (Italy); Molag, Menso [Nederlandse Organisatie voor toegepast-natuurwetenschappelijk onderzoek TNO, Princetonlaan 6, 3584 CB Utrecht (Netherlands); Cozzani, Valerio, E-mail: valerio.cozzani@unibo.it [CONPRICI - Dipartimento di Ingegneria Chimica, Mineraria e delle Tecnologie Ambientali, Alma Mater Studiorum - Universita di Bologna, Via Terracini 28 - 40131 Bologna (Italy)

2009-12-15

The improvement of passive fire protection of storage vessels is a key factor to enhance safety among the LPG distribution chain. A thermal and mechanical model based on finite elements simulations was developed to assess the behaviour of full size tanks used for LPG storage and transportation in fire engulfment scenarios. The model was validated by experimental results. A specific analysis of the performance of four different reference coating materials was then carried out, also defining specific key performance indicators (KPIs) to assess design safety margins in near-miss simulations. The results confirmed the wide influence of coating application on the expected vessel time to failure due to fire engulfment. A quite different performance of the alternative coating materials was evidenced. General correlations were developed among the vessel time to failure and the effective coating thickness in full engulfment scenarios, providing a preliminary assessment of the coating thickness required to prevent tank rupture for a given time lapse. The KPIs defined allowed the assessment of the available safety margins in the reference scenarios analyzed and of the robustness of thermal protection design.

Modeling the performance of coated LPG tanks engulfed in fires

International Nuclear Information System (INIS)

Landucci, Gabriele; Molag, Menso; Cozzani, Valerio

2009-01-01

The improvement of passive fire protection of storage vessels is a key factor to enhance safety among the LPG distribution chain. A thermal and mechanical model based on finite elements simulations was developed to assess the behaviour of full size tanks used for LPG storage and transportation in fire engulfment scenarios. The model was validated by experimental results. A specific analysis of the performance of four different reference coating materials was then carried out, also defining specific key performance indicators (KPIs) to assess design safety margins in near-miss simulations. The results confirmed the wide influence of coating application on the expected vessel time to failure due to fire engulfment. A quite different performance of the alternative coating materials was evidenced. General correlations were developed among the vessel time to failure and the effective coating thickness in full engulfment scenarios, providing a preliminary assessment of the coating thickness required to prevent tank rupture for a given time lapse. The KPIs defined allowed the assessment of the available safety margins in the reference scenarios analyzed and of the robustness of thermal protection design.

Preliminary proposed seismic design and evaluation criteria for new and existing underground hazardous materials storage tanks

International Nuclear Information System (INIS)

Kennedy, R.P.

1991-01-01

The document provides a recommended set of deterministic seismic design and evaluation criteria for either new or existing underground hazardous materials storage tanks placed in either the high hazard or moderate hazard usage catagories of UCRL-15910. The criteria given herein are consistent with and follow the same philosophy as those given in UCRL-15910 for the US Department of Energy facilities. This document is intended to supplement and amplify upon Reference 1 for underground hazardous materials storage tanks

The worldwide LPG market

International Nuclear Information System (INIS)

Dermont, V.

1998-01-01

The market of liquefied petroleum gases (LPG) concerns mainly the domestic uses (space and sanitary heating, cooking) but also some small industries, the agriculture and chemistry sectors and the transportation sector. This paper analyzes the European demand of LPG fuels by sector. (J.S.)

The role of the underground for massive storage of energy: a preliminary glance of the French case

Science.gov (United States)

Audigane, Pascal; Gentier, Sylvie; Bader, Anne-Gaelle; Beccaletto, Laurent; Bellenfant, Gael

2014-05-01

The question of storing energy in France has become of primary importance since the launch of a road map from the government which places in pole position this topic among seven major milestones to be challenged in the context of the development of innovative technology in the country. The European objective to reach 20% of renewables in the energy market, from which a large part would come from wind and solar power generation, raises several issues regarding the capacity of the grid to manage the various intermittent energy sources in line with the variability of the public demand and offer. These uncertainties are highly influenced by unpredictable weather and economic fluctuations. To facilitate the large-scale integration of variable renewable electricity sources in grids, massive energy storage is needed. In that case, electric energy storage techniques involving the use of underground are often under consideration as they offer a large storage capacity volume with a adapted potential of confining and the space required for the implantation. Among the panel of massive storage technologies, one can find (i) the Underground Pumped Hydro-Storage (UPHS) which are an adaptation of classical Pumped Hydro Storage system often connected with dam constructions, (ii) the compressed air storage (CAES) and (iii) the hydrogen storage from conversion of electricity into H2 and O2 by electrolysis. UPHS concept is based on using the potential energy between two water reservoirs positioned at different heights. Favorable natural locations like mountainous areas or cliffs are spatially limited given the geography of the territory. This concept could be extended with the integration of one of these reservoirs in an underground cavities (specifically mined or reuse of preexisting mines) to increase opportunities on the national territory. Massive storage based on compression and relaxation of air (CAES) requires high volume and confining pressure around the storage that exists

Method of disposing of earth contaminated by leaking underground storage tanks

International Nuclear Information System (INIS)

Ruehl, P.A.

1993-01-01

A process is described for disposing of earth contaminated with petroleum products from a leaking underground storage tank wherein the earth contains a significant amount of material comprised primarily of a mixture of one part Al 2 O 3 and two to three parts SiO 2 , the process comprising: digging up a leaking underground storage tank and the surrounding contaminated earth; separating the excavated earth into a Al 2 O 3 +SiO 2 material and a non-Al 2 O 3 + SiO 2 material; mixing the Al 2 O 3 + SiO 2 material and other cement precursor raw materials together to form a mixture, and grinding the mixture to form a feed mix; introducing the feed mix into a rotary cement kiln causing any remaining petroleum product contained therein to be volatilized and burned within the kiln as cement clinker is being produced; and grinding the cement clinker together to form cement which is free of petroleum product

European strategic issues for LPG

International Nuclear Information System (INIS)

Anon.

2006-01-01

A Strategic Team was set up at the AEGPL to: define an energy long term scenario, formulate a LPG road map, identify a positioning for LPG and determine a new image and a new name for the Association. The project will be presented in October, said Main De Greve (SHV) during the AEGPL Congress in Istanbul, where he presented a very interesting analysis on the LPG social and business environment. We publish this text below. (authors)

Estimating heel retrieval costs for underground storage tank waste at Hanford. Draft

International Nuclear Information System (INIS)

DeMuth, S.

1996-01-01

Approximately 100 million gallons (∼400,000 m 3 ) of existing U.S. Department of Energy (DOE) owned radioactive waste stored in underground tanks can not be disposed of as low-level waste (LLW). The current plan for disposal of UST waste which can not be disposed of as LLW is immobilization as glass and permanent storage in an underground repository. Disposal of LLW generally can be done sub-surface at the point of origin. Consequently, LLW is significantly less expensive to dispose of than that requiring an underground repository. Due to the lower cost for LLW disposal, it is advantageous to separate the 100 million gallons of waste into a small volume of high-level waste (HLW) and a large volume of LLW

Performance Analysis of Depleted Oil Reservoirs for Underground Gas Storage

Directory of Open Access Journals (Sweden)

Dr. C.I.C. Anyadiegwu

2014-02-01

Full Text Available The performance of underground gas storage in depleted oil reservoir was analysed with reservoir Y-19, a depleted oil reservoir in Southern region of the Niger Delta. Information on the geologic and production history of the reservoir were obtained from the available field data of the reservoir. The verification of inventory was done to establish the storage capacity of the reservoir. The plot of the well flowing pressure (Pwf against the flow rate (Q, gives the deliverability of the reservoir at various pressures. Results of the estimated properties signified that reservoir Y-19 is a good candidate due to its storage capacity and its flow rate (Q of 287.61 MMscf/d at a flowing pressure of 3900 psig

Indian Country Leaking Underground Storage Tanks, Region 9, 2016

Science.gov (United States)

This GIS dataset contains point features that represent Leaking Underground Storage Tanks in US EPA Region 9 Indian Country. This dataset contains facility name and locational information, status of LUST case, operating status of facility, inspection dates, and links to No Further Action letters for closed LUST cases. This database contains 1230 features, with 289 features having a LUST status of open, closed with no residual contamination, or closed with residual contamination.

200 Area plateau inactive miscellaneous underground storage tanks locations

International Nuclear Information System (INIS)

Brevick, C.H.

1997-01-01

Fluor Daniel Northwest (FDNW) has been tasked by Lockheed Martin Hanford Corporation (LMHC) to incorporate current location data for 64 of the 200-Area plateau inactive miscellaneous underground storage tanks (IMUST) into the centralized mapping computer database for the Hanford facilities. The IMUST coordinate locations and tank names for the tanks currently assigned to the Hanford Site contractors are listed in Appendix A. The IMUST are inactive tanks installed in underground vaults or buried directly in the ground within the 200-East and 200-West Areas of the Hanford Site. The tanks are categorized as tanks with a capacity of less than 190,000 liters (50,000 gal). Some of the IMUST have been stabilized, pumped dry, filled with grout, or may contain an inventory or radioactive and/or hazardous materials. The IMUST have been out of service for at least 12 years

Leishmania major glycosylation mutants require phosphoglycans (lpg2- but not lipophosphoglycan (lpg1- for survival in permissive sand fly vectors.

Directory of Open Access Journals (Sweden)

Anna Svárovská

2010-01-01

Full Text Available Sand fly species able to support the survival of the protozoan parasite Leishmania have been classified as permissive or specific, based upon their ability to support a wide or limited range of strains and/or species. Studies of a limited number of fly/parasite species combinations have implicated parasite surface molecules in this process and here we provide further evidence in support of this proposal. We investigated the role of lipophosphoglycan (LPG and other phosphoglycans (PGs in sand fly survival, using Leishmania major mutants deficient in LPG (lpg1(-, and the phosphoglycan (PG-deficient mutant lpg2(-. The sand fly species used were the permissive species Phlebotomus perniciosus and P. argentipes, and the specific vector P. duboscqi, a species resistant to L. infantum development.The lpg2(- mutants did not survive well in any of the three sand fly species, suggesting that phosphoglycans and/or other LPG2-dependent molecules are required for parasite development. In vitro, all three L. major lines were equally resistant to proteolytic activity of bovine trypsin, suggesting that sand fly-specific hydrolytic proteases or other factors are the reason for the early lpg2(- parasite killing. The lpg1(- mutants developed late-stage infections in two permissive species, P. perniciosus and P. argentipes, where their infection rates and intensities of infections were comparable to the wild type (WT parasites. In contrast, in P. duboscqi the lpg1(- mutants developed significantly worse than the WT parasites.In combination with previous studies, the data establish clearly that LPG is not required for Leishmania survival in permissive species P. perniciosus and P. argentipes but plays an important role in the specific vector P. duboscqi. With regard to PGs other than LPG, the data prove the importance of LPG2-related molecules for survival of L. major in the three sand fly species tested.

Controlling LPG temperature for SI engine applications

International Nuclear Information System (INIS)

Ceviz, Mehmet Akif; Kaleli, Alirıza; Güner, Erdoğan

2015-01-01

In this study, the effects of the LPG temperature on the engine performance and the exhaust emission characteristics have been investigated experimentally on an SI engine. In conventional injection systems, the LPG temperature increases excessively during the phase change in pressure regulator, and reduces the engine volumetric efficiency. According to the test results, engine performance and NO emission characteristics can be improved by controlling the LPG temperature before injecting to the engine intake manifold. A new control system taking into account the results of the study has been developed and tested. In order to control the LPG temperature, the coolant flow rate in pressure regulator circuit was arranged by using a control valve activated by a PID controller unit. Results of the study showed that the engine brake power loss can be increased by about 1.85% and NO emissions can be decreased by about 2% as compared to the operation with the original LPG injection system. - Highlights: • Effects of the LPG temperature have been examined. • Engine performance characteristics and exhaust emissions have been studied. • Results reveal that the LPG temperature should be kept in a range. • A prototype LPG temperature control system has been successfully developed

Large underground radioactive waste storage tanks successfully cleaned at Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Billingsley, K.; Burks, B.L.; Johnson, M.; Mims, C.; Powell, J.; Hoesen, D. van

1998-05-01

Waste retrieval operations were successfully completed in two large underground radioactive waste storage tanks in 1997. The US Department of Energy (DOE) and the Gunite Tanks Team worked cooperatively during two 10-week waste removal campaigns and removed approximately 58,300 gallons of waste from the tanks. About 100 gallons of a sludge and liquid heel remain in each of the 42,500 gallon tanks. These tanks are 25 ft. in diameter and 11 ft. deep, and are located in the North Tank Farm in the center of Oak Ridge National Laboratory. Less than 2% of the radioactive contaminants remain in the tanks, proving the effectiveness of the Radioactive Tank Cleaning System, and accomplishing the first field-scale cleaning of contaminated underground storage tanks with a robotic system in the DOE complex

RCRA corrective action for underground storage tanks -- Subtitle C for Subtitle I

International Nuclear Information System (INIS)

1995-08-01

The purpose of this report is to provide guidance to DOE and DOE contractor personnel responsible for planning and implementation of corrective measures addressing cleanup of releases of hazardous materials or regulated substances from underground storage tanks regulated under RCRA Subtitle C or Subtitle I

Bedrock instability of underground storage systems in the Czech Republic, Central Europe

Czech Academy of Sciences Publication Activity Database

Nováková, Lucie; Brož, Milan; Záruba, J.; Sosna, K.; Najser, J.; Rukavičková, L.; Franěk, J.; Rudajev, V.

2016-01-01

Roč. 13, č. 2 (2016), s. 315-325 ISSN 1672-7975 R&D Projects: GA MPO(CZ) FR-TI1/367 Institutional support: RVO:67985891 ; RVO:67985530 Keywords : underground storage * instability * seismicity * Bohemian Massif Subject RIV: DD - Geochemistry Impact factor: 0.796, year: 2016

METHODOLOGY FOR ESTIMATION OF STATIONARY AND DYNAMIC PARAMETERS FOR LIQUEFIED PETROLEUM GAS (LPG RE-LIQUEFACTION IN SPHERICAL STORAGE SYSTEMS

Directory of Open Access Journals (Sweden)

Alexander Mendoza-Acosta

2017-07-01

Full Text Available Temperature difference between the environment and the liquid contained in the liquefied petroleum gas storage spheres produces: net inward heat flow, increase in stored fuel temperature, LPG partial vaporization and consequently an increase in storage pressure. In order to maintain adequate safety conditions, since uncontrolled pressure increases could lead to risky situations and economic losses, re-liquefaction systems, consisting on auto refrigeration units, are installed; this system extracts the evaporated gas, compress it and then condense it again in a closed cooling cycle. Frequently these systems are designed using heuristic criteria, without considering the calculations necessary for correct equipment sizing; this results in costly modifications or in oversized equipment. In the present article, a simple but effective methodology for the calculation of thermal loads, daily temperature increase rate and pressure accumulation and restore times is presented, the methodology was compared with real data, through data acquisition and processing during the summer months of 2015 and 2016 for 12 storage spheres in a gas company located in a coastal state of Mexico, finding that the values predicted for the rate of daily temperature increase and recovery times are statistically consistent with the experimental data.

LPG a clean and efficient motor fuel: regulated and non-regulated emissions of a commercial attractive LPG vehicle

NARCIS (Netherlands)

Hollemans, B.H.

1996-01-01

Excise and other duties measures in Europe, threaten to affect the low price of LPG as a car fuel. As a result, this less polluting fuel would lose position. For this reason the Netherlands LPG industry commissioned TNO to undertake a study which would clearly demonstrate the advantages of LPG. The

Closure report for underground storage tank 141-R3U1 and its associated underground piping

Energy Technology Data Exchange (ETDEWEB)

Mallon, B.J.; Blake, R.G.

1994-03-01

Underground storage tank UST 141-R3U1 at Lawrence Livermore National Laboratory (LLNL), was registered with the State Water Resources Control Board on June 27, 1984. This tank system consisted of a concrete tank, lined with polyvinyl chloride, and approximately 100 feet of PVC underground piping. UST 141-R3U1 had a capacity of 450 gallons. The underground piping connected three floor drains and one sink inside Building 141 to UST 141-R3U1. The wastewater collected in UST 141-R3U1 contained organic solvents, metals, and inorganic acids. On November 30, 1987, the 141-R3U1 tank system failed a precision tank test. The 141-R3U1 tank system was subsequently emptied and removed from service pending further precision tests to determine the location of the leak within the tank system. A precision tank test on February 5, 1988, was performed to confirm the November 30, 1987 test. Four additional precision tests were performed on this tank system between February 25, 1988, and March 6, 1988. The leak was located where the inlet piping from Building 141 penetrates the concrete side of UST 141-R3U1. The volume of wastewater that entered the backfill and soil around and/or beneath UST 141-R3U1 is unknown. On December 13, 1989, the LLNL Environmental Restoration Division submitted a plan to close UST 141-R3U1 and its associated piping to the Alameda County Department of Environmental Health. UST 141-R3U1 was closed as an UST, and shall be used instead as additional secondary containment for two aboveground storage tanks.

Closure report for underground storage tank 141-R3U1 and its associated underground piping

International Nuclear Information System (INIS)

Mallon, B.J.; Blake, R.G.

1994-03-01

Underground storage tank UST 141-R3U1 at Lawrence Livermore National Laboratory (LLNL), was registered with the State Water Resources Control Board on June 27, 1984. This tank system consisted of a concrete tank, lined with polyvinyl chloride, and approximately 100 feet of PVC underground piping. UST 141-R3U1 had a capacity of 450 gallons. The underground piping connected three floor drains and one sink inside Building 141 to UST 141-R3U1. The wastewater collected in UST 141-R3U1 contained organic solvents, metals, and inorganic acids. On November 30, 1987, the 141-R3U1 tank system failed a precision tank test. The 141-R3U1 tank system was subsequently emptied and removed from service pending further precision tests to determine the location of the leak within the tank system. A precision tank test on February 5, 1988, was performed to confirm the November 30, 1987 test. Four additional precision tests were performed on this tank system between February 25, 1988, and March 6, 1988. The leak was located where the inlet piping from Building 141 penetrates the concrete side of UST 141-R3U1. The volume of wastewater that entered the backfill and soil around and/or beneath UST 141-R3U1 is unknown. On December 13, 1989, the LLNL Environmental Restoration Division submitted a plan to close UST 141-R3U1 and its associated piping to the Alameda County Department of Environmental Health. UST 141-R3U1 was closed as an UST, and shall be used instead as additional secondary containment for two aboveground storage tanks

Leaking Underground Storage Tank Points, Region 9 Indian Country, 2017, US EPA Region 9

Data.gov (United States)

U.S. Environmental Protection Agency — This GIS dataset contains point features that represent Leaking Underground Storage Tanks in US EPA Region 9 Indian Country. This dataset contains facility name and...

Underground storage tanks soft waste dislodging and conveyance

International Nuclear Information System (INIS)

Wellner, A.F.

1993-10-01

Currently 140 million liters (37 million gallons) of waste are stored in the single shell underground storage tanks (SSTs) at Hanford. The wastes contain both hazardous and radioactive constituents. This paper focuses on the Westinghouse Hanford Company's testing program for soft waste dislodging and conveyance technology. This program was initialized to investigate methods of dislodging and conveying soft waste. The main focus was on using air jets, water jets, and/or mechanical blades to dislodge the waste and air conveyance to convey the dislodged waste. These waste dislodging and conveyance technologies would be used in conjunction with a manipulator based retrieval system

Model based, sensor-directed remediation of underground storage tanks

International Nuclear Information System (INIS)

Harrigan, R.W.; Thunborg, S.

1990-01-01

Sensor-rich, intelligent robots that function with respect to models of their environment have significant potential to reduce the time and cost for the cleanup of hazardous waste while increasing operator safety. Sandia National Laboratories (SNL) is performing technology development and experimental investigations into the application of intelligent robot control technology to the problem of cleaning up waste stored in underground tanks. The tasks addressed in the SNL experiments are in situ physical characterizations of underground storage tanks (USTs) as well as the contained waste and the removal of the waste from the tank both for laboratory analysis and as part of the tank cleanup process. Both fully automatic and manual robot control technologies are being developed and demonstrated. The SNL-developed concept of human-assisted computer control will be employed whenever manual control of the robot is required. The UST Robot Technology Development Laboratory (URTDL) consists of a commercial gantry robot modified to allow hybrid force/position control

Africa gaining importance in world LPG trade

International Nuclear Information System (INIS)

Haun, R.R.; Otto, K.W.; Whitley, S.C.

1997-01-01

Major LPG projects planned or under way in Africa will increase the importance of that region's presence in world LPG trade. Supplies will nearly double between 1995 and 2005, at which time they will remain steady for at least 10 years. At the same time that exports are leveling, however, increasing domestic demand for PG is likely to reduce export-market participation by Algeria, Nigeria, Egypt, and Libya. The growth of Africa's participation in world LPG supply is reflected in comparisons for the next 15--20 years. Total world supply of LPG in 1995 was about 165 million metric tons (tonnes), of which Africans share was 7.8 million tonnes. By 2000, world supply will grow to slightly more than 200 million tonnes, with Africa's share expected to increase to 13.2 million tonnes (6.6%). And by 2005, world LPG supply will reach nearly 230 million tonnes; Africa's overall supply volumes by that year will be nearly 16.2 million tonnes (7%). World LPG supply for export in 1995 was on order of 44 million tonnes with Africa supply about 4 million tonnes (9%). By 2005, world export volumes of LPG will reach nearly 70 million tonnes; Africa's share will have grown by nearly 10 million tonnes (14.3%)

VOLUMETRIC LEAK DETECTION IN LARGE UNDERGROUND STORAGE TANKS - VOLUME II: APPENDICES A-E

Science.gov (United States)

The program of experiments conducted at Griffiss Air Force Base was devised to expand the understanding of large underground storage tank behavior as it impacts the performance of volumetric leak detection testing. The report addresses three important questions about testing the ...

Flammability characteristics of LPG

International Nuclear Information System (INIS)

Cardillo, Paolo

2005-01-01

The use of LPG is continuous increase not only in the domestic field but also in the field of the transports. Consequently, there is a renewed interest for its flammability characteristics in order to decide the necessary conditions of safety. The main components of LPG are hydrocarbons containing three or four carbon atoms. The normal components of LPG are propane and butane; small concentrations of other hydrocarbons (isobutene, propylene, butane, ethane, pentane) may also be present. Different mixtures of LGP have different and physical characteristics with a different behavior during the use. Also flammability characteristics can be different according to the composition. In this paper at firsts the flammability characteristics of the main components of LGP, taken singularly, are examinated; subsequently some examples of calculation of the flammability limits of different mixture are reported [it

High-temperature acquifer thermal storage and underground heat storage; IEA ECES Annex 12: Hochtemperatur-Erdwaermesonden- und Aquiferwaermespeicher

Energy Technology Data Exchange (ETDEWEB)

Sanner, B.; Knoblich, K. [Giessen Univ. (Germany). Inst. fuer Angewandte Geowissenschaften; Koch, M.; Adinolfi, M. [Stuttgart Univ. (Germany). Inst. fuer Siedlungswasserbau, Wasserguete und Abfallwirtschaft

1998-12-31

Heat storage is essential for the reconciliation of heat supply and demand. The earth has already proved to be an excellent medium for storing large amounts of heat over longer periods of time, for instance during the cold and hot season. The efficiency of the storage is the better the lower storage losses are at high temperature levels. Unfortunately this can not be easily achieved. While thermal underground stores, which are widely used for cold storage, have proved to perform quite well at temperatures between 10 C - 40 C, it has been rather difficult to achieve similar results at higher temperatures up to 150 C as test and demonstration plants of the 1980s proved. This issue has again attracted so much interest that the IEA launched a project on high temperature underground storage in December 1998. (orig.) [Deutsch] Waermespeicherung ist von entscheidender Bedeutung, wenn es darum geht, ein Waermeangebot mit einer Waermenachfrage zeitlich zur Deckung zu bringen. Der Untergrund hat sich schon seit vielen Jahren als ein geeignetes Medium erwiesen, groessere Waermepumpen ueber laengere Zeitraeume wie etwa die kalten und warmen Jahreszeiten zu speichern. Die Effizienz eines solchen Speichers steigt mit der Hoehe des erreichten Temperaturniveaus und mit sinkenden Speicherverlusten, was leider eher gegenlaeufige Erscheinungen sind. Waehrend thermische Untergrundspeicher im Temperaturbereich von 10-40 C inzwischen erfolgreich demonstriert wurden und vor allem zur Kaeltespeicherung auch bereits vielfach eingesetzt werden, haben hoehere Temperaturen bis etwa 150 C in den Versuchs- und Demonstrationsanlagen der 80er Jahre vielfaeltige Probleme bereitet. Im Gefolge eines erneuten Interesses an unterirdischer thermischer Energiespeicherung wurde im Dezember 1997 ein Vorhaben des IEA Energiespeicherprogramms zu Untergrund-Waermespeichern hoeherer Temperatur eingerichtet. (orig.)

Underground storage development in the Federal Republic of Germany

International Nuclear Information System (INIS)

Sponheuer, T.

1990-01-01

As the demand for gas in the Federal Republic of Germany is increasingly dependent upon temperature, underground storage is becoming a more and more important tool for the adjustment of supply load factors to the patterns of gas demand. Total working gas capacity is expected to double by the year 2000. Capacity requirements must be planned for a design winter, but allowances must also be made for operational flexibility, but management of incidents and the decrease in deliverability mainly from porous rock storage fields towards the end of the withdrawal season. Storage development potential in the Federal Republic of Germany is adequate for these requirements. However, the substantial uncertainties associated with the various factors determining future storage needs, administrative and licensing procedures, difficulties with regard to storage site acceptance by the general public and the resulting long project lead times confront gas companies from the Federal Republic of Germany with a complex planning problem and a major technical and commercial challenge, considering the estimated capital outlay of 4 to 5 billion DM in 1988 Deutschmarks. To master this challenge and to be able to provide secure and competitive gas supplies, the gas industry must continue to operate in a market economy which remains undistorted by new legislation and regulation. (author). 11 figs

Efficiency and impacts of hythane (CH4+H2) underground storage

Science.gov (United States)

Sáinz-García, Alvaro; Abarca, Elena; Grandia, Fidel

2016-04-01

The foreseen increase share of renewable energy production requires energy storage to mitigate shortage periods of energy supply. Hydrogen is an efficient energy carrier that can be transported and storage. A very promising way to store large amounts of hydrogen is underground geological reservoirs. Hydrogen can be stored, among other options, as a mixture of natural gas and less than 20% of hydrogen (hythane) to avoid damages on the existing infrastructure for gas transport. This technology is known as power-to-gas and is being considered by a number of European countries (Simon et al., 2015). In this study, the feasibility of a deep aquifer to store CH4-H2 mixtures in the Lower Triassic of the Paris Basin is numerically analyzed. The solubility of gas mixture in the groundwater is extremely low (Panfilov, 2015) and, therefore, gas and water are considered immiscible and non-reactive. An immiscible multiphase flow model is developed using the coefficient-form PDE interface of the finite element method code, COMSOL Multiphysics. The modelled domain is a 2D section of 2500 x 290 m resembling the Lower Triassic aquifer of the Paris basin, consisting of 2 layers of sandstone separated by a layer of conglomerates. The domain dips 0.5% from east to west. The top of the aquifer is 500 m-deep and the lateral boundaries are assumed to be open. This case is considered conservative compared to a dome-like geological trap, which could be more favorable to retain higher gas concentration. A number of cycles of gas production and injection were modelled. An automatic shut-down of the pump is implemented in case pressure on the well exceeds an upper or lower threshold. The influence of the position of the well, the uncertain residual gas saturation and the regional flow are studied. The model shows that both gas and aquifer properties have a significant impact on storage. Due to its low viscosity, the mobility of the hythane is quite high and gas expands significantly, reducing

Perspectives of the LPG-fuel market

International Nuclear Information System (INIS)

Anon.

1996-01-01

In today's context of environment protection cares and in agreement with the actions carried out by the local authorities and organizations, the LPG-fuel appears in the media with a reviving good and credible reputation. However, one can ask about its real perspectives of development. This short paper analyses the conditions for this development at the international and at the national scale. LPG-fuel is the most used and most performing alternative fuel in the world and can contribute to the energy independence of the countries with national LPG resources. Its technological mastery leads progressively the car manufacturers to propose vehicles already equipped with dual-fuel engines, but to reach its expected success, LPG-fuel needs a financial aid from the national authorities in the form of taxes reduction. Its privileged markets are the taxicabs, the public transportation systems and the fleets of intervention vehicles. In France, the network of LPG distribution stations is progressively reinforcing but a revision of the legal texts concerning the training of personnel and the approval of repair shops must be updated. (J.S.)

The underground laboratory. A unique scientific tool to design a reversible storage

International Nuclear Information System (INIS)

2010-07-01

The National Radioactive Waste Management Agency (Andra), was established by the December 1991 Waste Act as a public body in charge of the long-term management of all radioactive waste, under the supervision of the Ministry of Ecology, Energy, Sustainable Development and the Sea (formerly the Ministry of Industry and the Ministry of Environment), and the Ministry of Research. The Andra is carrying out studies on deep reversible waste storage for high-level and long living intermediate-level radioactive wastes thanks to the underground laboratory of its Meuse/Haute-Marne center. This brochure presents the geologic surveys which have led to the selection of the Callovo-Oxfordian argillite formation for the sitting of the underground lab and the underground architecture of the lab. The rock mechanic, heat transfer and rock-fluid interaction experiments carried out in the lab in collaboration with several scientific partners are briefly summarised

Perspectives of supply of LPG (Liquefied Petroleum Gases) in Brazil; Perespectivas de suprimento de GLP no Brasil

Energy Technology Data Exchange (ETDEWEB)

Costa, Luis Sebastiao [Universidade do Estado do Rio de Janeiro (UERJ), RJ (Brazil); Costa, Gildo Gabriel da; Moreira, Jose Guilherme de Souza [Agencia Nacional do Petroleo, Gas Natural e Biocombustiveis (ANP), Rio de Janeiro, RJ (Brazil)

2004-07-01

This work presents the indicative planning of the expansion of the infrastructure from liquefied petroleum gases (LPG) in the five years (2002-07). With base in the forecast of the demand - using the data of the offer, consumption, stock and the evaluation of the existent infrastructure (ports, terminals, tanks etc.) - it is evaluated the storage need and movement of the product. Compared to the period 1998-2003, a decrease was verified accentuated in the very superior consumption to the projected value. One of the causes was the increase in the price of LPG; other, the reduction in the number of the homes with LPG. Being considered the sceneries of LPG in this five years and the number of families, the perspective is the reduction of 5,6% in the consumption of LPG, being reached 6.307 thousand tons in 2007. For the period for an increase of 20% is waited in the offer it interns of the product that, together with the smallest demand, it will provoke a reduction of more than a fourth of the imports: 1.763 kt in 2002, for 403 kt in 2007. In spite of the reduction in the consumption and maintenance of the stock, the estimate of LPG will only increase of 20,6 days for 21,8 days, however the Brazil will be self-sufficient. (author)

Underground storage tanks: State regulations and compliance strategies

International Nuclear Information System (INIS)

Robinson, J.E.

1988-01-01

In an effort to resolve underground storage tank (UST) management problems, several states and localities have moved ahead of EPA in the promulgation of UST regulations. Developed independently, these regulations represent different strategies for ensuring compliance: from an extensive set of permitting requirements that allow for the implementation of site-specific control measures to a uniform set of technical and operational requirements that vary according to installation date. For the tank owner, complying with these regulations can be a time-consuming and frustrating endeavor. However, during the course of several environmental audits of similar facilities in different states, useful strategies were observed or developed that enabled facilities to respond more effectively to requirements: these included computerization of files, designation of tank custodians, installation of low-maintenance equipment, and increased use of above-ground tanks. Of special additional interest was the wide variation in costs for similar tank services quoted by both private and government sources. These strategies are coupled with general observations on the efficacy of the various regulatory approaches to provide a field view that may be useful to tank owners and others involved in underground tank management and evaluation

FY 1999 research and development results. Preparatory study for the underground thermal energy storage system; 1999 nendo chichu jiban chikunetsu system gijutsu sendo kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

The study is conducted for the underground thermal energy storage system which utilizes heat capacity of the underground, e.g., aquifer, to exchange heat with the underground, and the FY 1999 results are described. For establishment of the concept of the underground heat storage systems, 2 sites are selected for each of Tokyo, Osaka and Sapporo for the study as the geological ground models, for their weather characteristics. Two cases are considered for the site where underground heat exchangers are installed, open space and immediately below a building. The heat-storage system comprises a high-efficiency heat pump, water heat-storage tank and cooling tower. The evaluation results indicate that energy saving rate of 37% or more and CO2 reduction rate of 9.5% or more are achievable in all areas except Sapporo, i.e., Tokyo and Osaka. The economic evaluation results indicate that the simple pay-out period is around 100 years for Tokyo and Osaka, and 80 years for Sapporo. The underground heat storage system is approximately 10% lower in life-cycle cost than the conventional system, 3 versus 3.3 billion yen for the period of 60 years. (NEDO)

Underground storage at Saint-Illiers-la-Ville. Initial results of filling. Reservoir control problems

Energy Technology Data Exchange (ETDEWEB)

Vernet, D

1968-01-01

The underground storage at Saint-Illiers-la-Ville (Yvelines in the Paris area) was discussed by Toche at the time when it was filled with gas in 1965. Now, 2-1/2 yr after the initial input, the volume of storage has reached 500 million cu m, and the first industrial withdrawals took place during the winter of 1967-1968. The results obtained in the operation of this underground storage are extremely satisfactory. In spite of differences in the composition of the sand layer, the gas bubble developed in a very regular way, horizontally and vertically, and the full penetration well equipment made a high output rate easy to obtain. Reservoir control was handled efficiently and the movements of the bubble contour were shown for every fluctuation of the injection and withdrawal volumes. Tests for production capacity showed the low extent to which the wells were affected by the phenomenon of water- coning and indicated measures to be taken to prevent the formation of hydrates. The measures effected and the conclusions which can be derived are discussed.

A study to design the emergency reaction plan for LPG tanks in 5 th ...

African Journals Online (AJOL)

PROMOTING ACCESS TO AFRICAN RESEARCH ... On the other hand, today, with increased density and proximity of industrial units, the adverse consequences ... This study aims to identify the risks in LPG storage unit, 5th South Pars Gas Refinery and possible events ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

Achievement report for fiscal 1993. International clean energy system technology to utilize hydrogen - WE-NET (Sub-task 5. Development of hydrogen transportation and storage technology - Edition 3. Development of liquid hydrogen storage facility); 1993 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) (Sub tusk 5: Suiso yuso chozo gijutsu no kaihatsu - Dai 3 hen. Ekitai suiso chozo setsubi no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

With an intention to establish a technology required to build a hydrogen storage tank with a storage capacity of 50,000 m{sup 3} as the target shown in the basic plan for WE-NET, the current fiscal year has performed the technical literature surveys to identify the existing technologies. In the survey on the similar large storage system, a liquefied natural gas (LNG) was taken up, and the survey on the LNG bases in Japan was carried out. With regard to the existing liquefied hydrogen storage system, surveys were performed on the test site for developing the liquefied hydrogen/liquefied oxygen engines, the rocket launch sites, and liquefied hydrogen manufacturing plant. In relation with peripheral technologies for the underground storage tank being an excellent anti-seismic form, the LNG underground storage facilities were surveyed. Regarding the rock mass storage tank, surveys were carried out on the LPG rock mass storage having been used practically, and the LNG rock mass storage that is in the demonstration phase. In the research on storage facilities, surveys were executed on the forms and heat insulation structures of the similar large low-temperature storage tanks, the use record of the existing liquefied hydrogen storage tanks, heat insulating materials, and heat insulating structures. (NEDO)

Emissions from ethanol- and LPG-fueled vehicles

International Nuclear Information System (INIS)

Pitstick, M.E.

1995-01-01

This paper addresses the environmental concerns of using neat ethanol and liquefied petroleum gas (LPG) as transportation fuels in the United States. Low-level blends of ethanol (10%) with gasoline have been used as fuels in the United States for more than a decade, but neat ethanol (85% or more) has only been used extensively in Brazil. LPG, which consists mostly of propane, is already used extensively as a vehicle fuel in the United States, but its use has been limited primarily to converted fleet vehicles. Increasing U.S. interest in alternative fuels has raised the possibility of introducing neat-ethanol vehicles into the market and expanding the number of LPG vehicles. Use of such vehicles, and increased production and consumption of fuel ethanol and LPG, will undoubtedly have environmental impacts. If the impacts are determined to be severe, they could act as barriers to the introduction of neat-ethanol and LPG vehicles. Environmental concerns include exhaust and evaporative emissions and their impact on ozone formation and global warming, toxic emissions from fuel combustion and evaporation, and agricultural impacts from production of ethanol. The paper is not intended to be judgmental regarding the overall attractiveness of ethanol or LPG as compared with other transportation fuels. The environmental concerns are reviewed and summarized, but only conclusion reached is that there is no single concern that is likely to prevent the introduction of neat-ethanol-fueled vehicles or the increase in LPG-fueled vehicles

Indian Country Leaking Underground Storage Tank (LUST) Points, Region 9, 2016, US EPA Region 9

Data.gov (United States)

U.S. Environmental Protection Agency — This GIS dataset contains point features that represent Leaking Underground Storage Tanks in US EPA Region 9 Indian Country. This dataset contains facility name and...

Los Alamos National Laboratory environmental restoration program group audit report for underground storage tank removal: Audit ER-92- 04, July 22--August 11, 1992

International Nuclear Information System (INIS)

Gillespie, P.F.

1992-01-01

Audit ER-92-04 was conducted on activities being performed by Waste Management (EM-7), Environmental Protection (EM-8), and Environmental Restoration (EM-13) groups for the LANL's underground storage tank removal program. Scope of the audit was limited to an evaluation of the implementation of the State of New Mexico requirements for underground storage-tank removal. Activities were evaluated using requirements specified in the State of New Mexico Environmental Improvement Board Underground Storage Tank Regulations, EIB/USTR. Two recommendations are made: (1) that a single organization be given the responsibility and authority for the implementation of the program, and (2) that the requirements of the NM State environmental improvement board underground storage tank regulations be reviewed and a Los Alamos procedure written to address requirements and interfaces not contained in SOP-EM7-D ampersand D-001

Specialized video systems for use in underground storage tanks

International Nuclear Information System (INIS)

Heckendom, F.M.; Robinson, C.W.; Anderson, E.K.; Pardini, A.F.

1994-01-01

The Robotics Development Groups at the Savannah River Site and the Hanford site have developed remote video and photography systems for deployment in underground radioactive waste storage tanks at Department of Energy (DOE) sites as a part of the Office of Technology Development (OTD) program within DOE. Figure 1 shows the remote video/photography systems in a typical underground storage tank environment. Viewing and documenting the tank interiors and their associated annular spaces is an extremely valuable tool in characterizing their condition and contents and in controlling their remediation. Several specialized video/photography systems and robotic End Effectors have been fabricated that provide remote viewing and lighting. All are remotely deployable into and from the tank, and all viewing functions are remotely operated. Positioning all control components away from the facility prevents the potential for personnel exposure to radiation and contamination. Overview video systems, both monaural and stereo versions, include a camera, zoom lens, camera positioner, vertical deployment system, and positional feedback. Each independent video package can be inserted through a 100 mm (4 in.) diameter opening. A special attribute of these packages is their design to never get larger than the entry hole during operation and to be fully retrievable. The End Effector systems will be deployed on the large robotic Light Duty Utility Arm (LDUA) being developed by other portions of the OTD-DOE programs. The systems implement a multi-functional ''over the coax'' design that uses a single coaxial cable for all data and control signals over the more than 900 foot cable (or fiber optic) link

The performances of the LPG-fueled vehicle

International Nuclear Information System (INIS)

Anon.

1996-01-01

Todays, LPG-fueled vehicles are simply equipped with transformed classical petrol engines. The LPG consumption is greater but the emission of pollutants is greatly reduced (from 40 to 98% for the CO and from 30 to 80% for the HC and NOx, depending on the temperature of use). This short paper summarizes the environmental advantages of the LPG-fueled vehicles and the forthcoming technological evolutions expected in Europe, Japan and the USA. (J.S.)

30 CFR 75.1912 - Fire suppression systems for permanent underground diesel fuel storage facilities.

Science.gov (United States)

2010-07-01

... Diesel-Powered Equipment § 75.1912 Fire suppression systems for permanent underground diesel fuel storage... system by a nationally recognized independent testing laboratory and appropriate for installation at a... recommended inspection and maintenance program and as required by the nationally recognized independent...

The underground storage tank is the key; Der Speicher ist der Schluessel

Energy Technology Data Exchange (ETDEWEB)

Meyer, Jens-Peter

2013-08-06

Plus energy houses also succeed withoutpassive house insulation. Because the combination of solar collectors, ventilation and heat pump achieves excellent energy efficiency, if one preserves the solar heat in an underground storage tank. [German] Plusenergiehaeuser gelingen auch ohne Passivhausdaemmung. Denn die Kombination von Sonnenkollektoren, Lueftung und Waermepumpe erreicht eine ausgezeichnete energetische Effizienz, sofern man die Solarwaerme in einem Erdspeicher konserviert.

Green LPG

Energy Technology Data Exchange (ETDEWEB)

Hulteberg, Christian; Brandin, Jan; Leveau, Andreas (Biofuel-Solution AB, Limhamn (Sweden))

2010-12-15

The use of energy gases with renewable origins will become important with diminishing fossil resources. This as the infrastructure of the gaseous fuels is well built out and the distribution networks already exist. LPG is one of the most versatile fuels around, perfect for rural areas and in many other applications. The fossil origin of the fuel will, in today's climate and environmental debate, however position it as a thing of the past and not part of the future energy supply. The technology and development performed under this and previous programs with the Swedish Gas Centre will however suggest a way to bridge this conception and make LPG a part of the future energy mix. This report constitutes the results from the development performed under the SGC program 210 and is aimed at verifying the results from the previous SGC program 198, proving the concept for producing propane from renewable glycerol. Attractive and potentially profitable LPG premium segments that can be reached by producing bio-propane would be the autogas market. Another attractive segment to target is the outdoor and camping segment, where there already exist awareness for nature and the environment. A third interesting segment is in small-scale heat or combined heat and power generation, where a premium price can be reaped for renewable energy as well as the addition of LPG to biogas. Another important aspect of the renewable LPG is that it motivates external stakeholders, such as local, regional, national and international governments as well as environmental and other lobby groups to consider LPG a part of the future energy mix and not a thing of the past. A good starting point for two and three carbon energy gases is glycerine, with its three carbon backbone. The reason for focusing on glycerine is its benign chemical nature, it is: - Harmless from a toxic standpoint; - Chemically inert; - Non-corrosive; - Relatively high energy density; - Zero carbon dioxide emissions. It is also

RADIATION SAFETY JUSTIFICATION FOR THE LONG-TERM STORAGE OF GAS CONDENSATE IN THE UNDERGROUND RESERVOURS FORMED BY THE NUCLEAR EXPLOSION TECHNOLOGY

Directory of Open Access Journals (Sweden)

I. K. Romanovich

2010-01-01

Full Text Available The paper presents approaches to the safety justification of the gas condensate and brine long-term storage in the underground reservoirs formed by the nuclear explosion technology. Gas condensate and brine are the intermediate level liquid radioactive waste containing isotopes: 3Н, 137Cs and 90Sr, in traces - 239Pu, 235U, 241Am.Safety of the gas condensate and brine long-term storage in the underground reservoirs is assessed on the base of the multi-barrier principle implementation, used during radioactive waste disposal. It is shown that the gas condensate and brine long-term storage in the sealed underground reservoirs formed by nuclear explosion technologies in salt domes does not lead to the surface radioactive contamination and population exposure.

Reductie BLEVE-frequentie van een LPG-tankauto op een autotankstation

NARCIS (Netherlands)

Kok, O.M.P.; Pietersen, C.M.

1985-01-01

Uit de LPG-Integraalstudie [4] blijkt dat de BLEVE van de LPG-Tankauto het risico van het autotankstation domineert (bij ondergrondse opslagtank). In deze studie is nagegaan wat de invloed is van een aantal mogelijk te treffen voorzieníngen aan de LPG-tankauto en het LPG-autotankstation op de

RECOMMENDATIONS ON THE MONITORING SYSTEM OF UNDERGROUND GAS STORAGE (in Russian

Directory of Open Access Journals (Sweden)

Victor NORDIN

2014-07-01

Full Text Available The article in accordance with the "process approach" ISO 9000 is substantiated the necessity of creating underground gas storage system monitoring and control, including objects, parameters, methods, frequency and corrective action, on the basis of which made structural formula monitoring cycle. Qualimetrical approach allows to define complex criteria of an estimation of efficiency of operation, which will help to make timely and effective management decisions, including from the perspective of environmental protection.

Domestic LPG interventions in South Africa: Challenges and lessons

International Nuclear Information System (INIS)

Kimemia, David; Annegarn, Harold

2016-01-01

A majority of grid-connected households in South Africa use electricity for cooking and heating tasks. This thermal intensive use of electricity has a high load factor and is a contributory factor of electricity demand outstripping supply at peak demand periods. The government has promoted liquefied petroleum gas (LPG) as an alternative thermal energy source for household cooking and heating. This study evaluates the long-term successes, challenges and social impacts of an LPG intervention project that was piloted in Atteridgeville Township, a typical low-income suburb. The data was gathered through one-on-one household interviews with a sample of the beneficiaries. The results indicate that seven years after the LPG intervention, about 70% of the beneficiaries continue to use LPG and report that the intervention has improved their welfare. Fast cooking is cited as the key tangible benefit of LPG technology in households, followed by saving on electricity bills. The project would have achieved more success through better community engagement, including strict beneficiary selection criteria; a long-term LPG distribution and maintenance plan; and inclusion of recurring monthly LPG subsidies for indigent households. The study discusses the subset of factors necessary for successful rollouts of similar energy projects. - Highlights: •LPG has replaced earlier combustion fuels as preferred energy for cooking. •Fast cooking, cleanliness and saving on electricity bills are the key benefits. •The demand for LPG has stimulated economic models for supply and delivery. •Periodic shortages and non-adherence to price caps deter market expansion.

Environmental consequences of parallel marketing of LPG in India

International Nuclear Information System (INIS)

Das, T.K.; Deb, C.; Jash, T.

2000-01-01

In 1993, the government of India introduced a parallel marketing system for petroleum products, particularly for liquefied petroleum gas (LPG). LPG, under the parallel marketing system, is distributed at higher price without any subsidy. The government distributors, however, distribute LPG at subsidized rate. The consumers who get LPG at higher price, therefore, opt for a mixed energy use. The present study, based on a field survey, deals with the pattern of this mixed energy use and its environmental consequences. (author)

A basic study on underground storage of LNG

Energy Technology Data Exchange (ETDEWEB)

Kim, Min-Kyu; Lee, Kyung-Han; Kang, Sun-Duck [Korea Institute of Geology Mining and Materials, Taejon (KR)] (and others)

1999-12-01

In 1997, import of LNG was 11,378 thousand of about 2.3 billion US dollars. The demand of LNG(Liquefied Natural Gas) in Korea has been increased since 1987 with the rate of 20% annually. It is also estimated that this trend will be continued until 2010. Long-term estimation says that demand will increase with 9.1% and total demand of 2010 will be 23 million ton that is four times larger than that of 1994. Bases of unloading and store of LNG is necessary to complete the network of LNG distribution system to cover all of the country from import to final supply terminal at home. The construction plan of LNG bases with 49 tanks was published and is going on now at three bases, Pyungtaek, Incheon and Tongyoung. The total cost for this construction will be over 5,400 billion Won. All the LNG tanks are planned to build on the surface. The construction of LNG tanks on the surfaces is conventional but it damage the surface green area and is very vulnerable on safety, especially in Korea Peninsula with potentially unstable of military confrontation. And Korea is so small and limited in available land that it is not easy to find proper places for construction of more LNG tanks on surface. Underground LNG stores in rock will be a good alternative for tanks on surface in the view points of environmental and safety. It is also reported that it can be cheaper than that of on surfaces. It is well known that bed rocks in Korea is good to build underground structure like LNG stores. This report is basic research to seek for the possibility of LNG store construction in underground rocks. The important two questions on it is that whether it is possible technically and economically or not. The technical focus in this report is the stability of underground cavern for storage of LNG, energy conservation in operation, tightness against leakage of stored gas to surface and safety. Some statistic on LNG in Korea is given for this study with its future. (author). 25 refs., 36 tabs., 88 figs.

The European automotive LPG market

International Nuclear Information System (INIS)

Anon.

1998-01-01

The European automotive LPG market could reach at least 4 % of the European fuel market in 2005 versus 1 % in 1990. This would represent a rise of about 35 % in automotive LPG sales (from 2,4 million tonnes in 1997 to 7 million tonnes estimated for 2005). This was underlined by Alain Deleuse, Primagaz group's Marketing Director, in the paper he delivered at the AEGPL Budapest Convention. We publish large excepts of this paper. (author)

Rancang Bangun Sistem Pengaman Kebocoran Gas LPG (Liquefied Petroleum Gas) Menggunakan Mikrokontroler

OpenAIRE

Ismai, Reza Lutfi; Suseno, Jatmiko Endro; Suryono, Suryono

2017-01-01

Design of LPG gas leakage safety system using microcontroller has been made in this research. The purpose of this research is to make LPG gas sensor circuit to detect LPG gas concentration and make automation systems for LPG gas leakage protection. LPG gas leakage protection system can be applied for the use of LPG gas safely. Component to detect LPG gas concentration use sensor MQ 5 which can gives resistance as the output value which can be converted into voltage through the voltage devider...

The Cigeo project: an industrial storage site for radioactive wastes in deep underground

International Nuclear Information System (INIS)

Krieguer, Jean-Marie

2017-01-01

In 2006, France has decided to store its high-level and long-lived radioactive wastes, mostly issued from the nuclear industry, in a deep geological underground disposal site. This document presents the Cigeo project, a deep underground disposal site (located in the East of France) for such radioactive wastes, which construction is to be started in 2021 (subject to authorization in 2018). After a brief historical review of the project, started 20 years ago, the document presents the radioactive waste disposal context, the ethical choice of underground storage (in France and elsewhere) for these types of radioactive wastes, the disposal site safety and financing aspects, the progressive development of the underground facilities and, of most importance, its reversibility. In a second part, the various works around the site are presented (transport, buildings, water and power supply, etc.) together with a description of the various radioactive wastes (high and intermediate level and long-lived wastes and their packaging) that will be disposed in the site. The different steps of the project are then reviewed (the initial design and initial construction phases, the pilot industrial phase (expected in 2030), the operating phase, and the ultimate phases that will consist in the definitive closure of the site and its monitoring), followed by an extensive description of the various installations of surface and underground facilities, their architecture and their equipment

Assessment of feasible strategies for seasonal underground hydrogen storage in a saline aquifer

Science.gov (United States)

Sáinz-García, Alvaro; Abarca, Elena; Rubí, Violeta; Grandia, Fidel

2017-04-01

Renewable energies are unsteady, which results in temporary mismatches between demand and supply. The conversion of surplus energy to hydrogen and its storage in geological formations is one option to balance this energy gap. This study evaluates the feasibility of seasonal storage of hydrogen produced from wind power in Castilla-León region (northern Spain). A 3D multiphase numerical model is used to test different extraction well configurations during three annual injection-production cycles in a saline aquifer. Results demonstrate that underground hydrogen storage in saline aquifers can be operated with reasonable recovery ratios. A maximum hydrogen recovery ratio of 78%, which represents a global energy efficiency of 30%, has been estimated. Hydrogen upconing emerges as the major risk on saline aquifer storage. However, shallow extraction wells can minimize its effects. Steeply dipping geological structures are key for an efficient hydrogen storage.

Indian Country Leaking Underground Storage Tanks (LUST) Map Service, Region 9, 2016, US EPA Region 9

Data.gov (United States)

U.S. Environmental Protection Agency — This map service displays Leaking Underground Storage Tanks in US EPA Region 9 Indian Country. The service is composed of three layers; one for each unique LUST...

LPG market in sub Saharan Africa

International Nuclear Information System (INIS)

Belguedj, M.

1999-01-01

This article provides an overview of the current state of the liquefied petroleum gases (LPG) market in sub Saharan Africa (SSA) and analyses the supply and demand patterns, the constraints on supply imposed by the insufficient output from refineries unable to meet the increasing demand, and institutional and regulatory issues. Details are given of the pricing policies, the economic benefits that could be obtained by increasing the scale of operations, the use of subsidies, private sector participation, and LPG activities in Angola, Cameroon, the Congo, and the Ivory Coast. The role of the World Bank in the Africa Gas Initiative to promote the use of natural gas reserves in SSA, and requirements for developing the LPG market are discussed

A simulation for predicting potential cooling effect on LPG-fuelled vehicles

Science.gov (United States)

Setiyo, M.; Soeparman, S.; Wahyudi, S.; Hamidi, N.

2016-03-01

Liquefied Petroleum Gas vehicles (LPG Vehicles) provide a potential cooling effect about 430 kJ/kg LPG consumption. This cooling effect is obtained from the LPG phase change from liquid to vapor in the vaporizer. In the existing system, energy to evaporate LPG is obtained from the coolant which is circulated around the vaporizer. One advantage is that the LPG (70/30 propane / butane) when expanded from 8 bar to at 1.2 bar, the temperature is less than -25 °C. These conditions provide opportunities to evaporate LPG with ambient air flow, then produce a cooling effect for cooling car's cabin. In this study, some LPG mix was investigated to determine the optimum condition. A simulation was carried out to estimate potential cooling effects of 2000 cc engine from 1000 rpm to 6000 rpm. In this case, the mass flow rate of LPG is a function of fuel consumption. The simulation result shows that the LPG (70/30 propane/butane) provide the greatest cooling effect compared with other mixtures. In conclusion, the 2000 cc engine fueled LPG at 3000 rpm provides potential cooling effect more than 1.3 kW, despite in the low engine speed (1000 rpm) only provides about 0.5 kW.

The impact of waterborne LPG imports on US markets

International Nuclear Information System (INIS)

Lindsey, L.

1994-01-01

After a winter like most of the US has gone through this year it is certainly apropos to discuss the effect of waterborne LPG imports on the market. Due to time constraints this paper will be limited to global LPG activity as it relates to the US. To provide some credibility to the following comments, it should be stated that Commercial Services Company tracks every large LPG carrier in the world from the LPG lifting point to it's discharge destination and the commercial activity involved in the delivery

High water level installation of monitoring wells for underground storage tanks

International Nuclear Information System (INIS)

Treadway, C.

1990-01-01

This paper briefly describes a common monitoring well installation design for shallow ground water contamination resulting from leaky underground storage tanks. The paper describes drilling techniques used in unconsolidated Florida aquifers using hollow-stem augers. It describes methods for the prevention of heaving sands and sand-locking problems. It then goes on to describe the proper well casing placement and sealing techniques using neat cements. The proper sell screen level is also discussed to maximize the detection of floating hydrocarbons

The mechanism study between 3D Space-time deformation and injection or extraction of gas pressure change, the Hutubi Underground gas storage

Science.gov (United States)

Xiaoqiang, W.; Li, J.; Daiqing, L.; Li, C.

2017-12-01

The surface deformation of underground gas reservoir with the change of injection pressure is an excellent opportunity to study the load response under the action of tectonic movement and controlled load. This paper mainly focuses on the elastic deformation of underground structure caused by the change of the pressure state of reservoir rock under the condition of the irregular change of pressure in the underground gas storage of Hutubi, the largest underground gas storage in Xinjiang, at the same time, it makes a fine study on the fault activities of reservoir and induced earthquakes along with the equilibrium instability caused by the reservoir. Based on the 34 deformation integrated observation points and 3 GPS continuous observation stations constructed in the underground gas storage area of Hutubi, using modern measurement techniques such as GPS observation, precise leveling survey, flow gravity observation and so on, combined with remote sensing technology such as InSAR, the 3d space-time sequence images of the surface of reservoir area under pressure change were obtained. Combined with gas well pressure, physical parameters and regional seismic geology and geophysical data, the numerical simulation and analysis of internal changes of reservoir were carried out by using elastic and viscoelastic model, the deformation mechanical relationship of reservoir was determined and the storage layer under controlled load was basically determined. This research is financially supported by National Natural Science Foundation of China (Grant No.41474016, 41474051, 41474097)

Report on technical feasibility of underground pumped hydroelectric storage in a marble quarry site in the Northeast United States

Energy Technology Data Exchange (ETDEWEB)

Chas. T. Main, Inc.

1982-03-01

The technical and economic aspects of constructing a very high head underground hydroelectric pumped storage were examined at a prefeasibility level. Excavation of existing caverns in the West Rutland Vermont marble quarry would be used to construct the underground space. A plant capacity of 1200 MW and 12 h of continuous capacity were chosen as plant operating conditions. The site geology, plant design, and electrical and mechanical equipment required were considered. The study concluded that the cost of the 1200 MW underground pumped storage hydro electric project at this site even with the proposed savings from marketable material amounts to between $581 and $595 per kilowatt of installed capacity on a January 1982 pricing level. System studies performed by the planning group of the New England Power System indicate that the system could economically justify up to about $442 per kilowatt on an energy basis with no credit for capacity. To accommodate the plant with the least expensive pumping energy, a coal and nuclear generation mix of approximately 65% would have to be available before the project becomes feasible. It is not expected that this condition can be met before the year 2000 or beyond. It is therefore concluded that the West Rutland underground pumped storage facility is uneconomic at this time. Several variables however could have marked influence on future planning and should be examined on periodic basis.

A stronger perfume for LPG

International Nuclear Information System (INIS)

Willcox, C.K.

1996-01-01

The odorisation of Liquefied Petroleum Gas (LPG) is undertaken to improve the safe use and transport of this popular fuel. Effective LPG odorisation should enable leaks to be detected by any person with a normal sense of smell before gas concentrations reach a hazardous level. The objective is identical to that for odorising natural gas. However, the physical characteristics of propane and butane present particular difficulties. These do not occur with natural gas, which has a dynamic, flowing, simple-phase system. (author)

A stronger perfume for LPG

Energy Technology Data Exchange (ETDEWEB)

Willcox, C.K.

1996-11-01

The odorisation of Liquefied Petroleum Gas (LPG) is undertaken to improve the safe use and transport of this popular fuel. Effective LPG odorisation should enable leaks to be detected by any person with a normal sense of smell before gas concentrations reach a hazardous level. The objective is identical to that for odorising natural gas. However, the physical characteristics of propane and butane present particular difficulties. These do not occur with natural gas, which has a dynamic, flowing, simple-phase system. (author)

LPG as a Fuel for Diesel Engines-Experimental Investigations

Science.gov (United States)

Cristian Nutu, Nikolaos; Pana, Constantin; Negurescu, Niculae; Cernat, Alexandru; Mirica, Ionel

2017-10-01

The main objective of the paper is to reduce the pollutant emissions of a compression ignition engine, fuelling the engine with liquefied petroleum gas (LPG), aiming to maintain the energetic performances of the engine. To optimise the engine operation a corelation between the substitute ratio of the diesel fuel with LPG and the adjustments for the investigated regimens must be made in order to limit the maximum pressure and smoke level, knock and rough engine functioning, fuel consumption and the level of the pollutant emissions. The test bed situated in the Thermotechnics, Engines, Thermal Equipments and Refrigeration Instalations Department was adapted to be fuelled with liquefied petroleum gas. A conventional LPG fuelling instalation was adopted, consisting of a LPG tank, a vaporiser, conections between the tank and the vaporiser and a valve to adjust the gaseous fuel flow. Using the diesel-gas methode, in the intake manifold of the engine is injected LPG in gaseous aggregation state and the airr-LPG homogeneous mixture is ignited from the flame appeared in the diesel fuel sprays. To maintain the engine power at the same level like in the standard case of fuelling only with diesel fuel, for each investigated operate regimen the diesel fuel dose was reduced, being energetically substituted with LPG. The engine used for experimental investigations is a turbocharged truck diesel engine with a 10.34 dm3 displacement. The investigated working regimen was 40% load and 1750 rpm and the energetic substitute ratios of the diesel fuel with LPG was situated between [0-25%].

Conformity checking of LPG Transportation Trucks by Modelling and Simulation

OpenAIRE

Gallab , Maryam; Bouloiz , Hafida; Tkiouat , Mohamed; Garbolino , Emmanuel

2016-01-01

International audience; LPG Loading /unloading site is considered as a dangerous environment of significant risk, especially during LPG transfer operations. These risks may cause catastrophic dangers such as BLEVE (Boiling Liquid Expanding Vapour Explosion), UVCE (Unconfined Vapour Cloud Explosion), etc. The site consists of a tank (RST) containing LPG and threetransfer posts. Two posts allow loading of small carrier tankers 6 tons. The other one transfer post transfer LPG contained injumbo t...

An Assessment of Hydrological Safety for the Guri Underground Oil Storage Facility

Energy Technology Data Exchange (ETDEWEB)

Kim, Geon Young; Kim, Kyung Su; Koh, Yong Kwon; Bae, Dae Seok; Park, Kyung Woo; Ji, Sung Hoon; Ryu, Ji Hoon

2009-08-15

Hydrological and geochemical analysis of the various kinds of water including observation borehole groundwater was carried out for the assessment of the hydrological safety of the underground oil storage cavern and the potentiality of mineralogical and microbiological clogging was estimated. There was no distinct chemical difference in the various kinds of water. All kinds of water are undersaturated with the calcite which is the major clogging mineral. Most water samples have low Fe and Mn concentrations. However, they are saturated or oversaturated with the iron-oxide/hydroxide minerals and have high dissolved oxygen contents which softiies the possibility of clogging by the iron-oxide/hydroxide minerals as a long-term aspect. Statistical analysis shows the degree of mineral precipitation or dissolution is mainly controlled by pH, Eh and DO of water samples. Because the slime forming bacteria ate dominant microbe in several observation boreholes, the clogging can be caused by it as a long-term aspect. In addition, the possibility of clogging can be increased if the microbial effect is combined with the mineralogical effect such as iron oxide/hydroxide minerals for the possibility of clogging. Therefore, the systematic and long-term program for the assessment of clogging is required for the safe operation of underground oil storage cavern.

An Assessment of Hydrological Safety for the Guri Underground Oil Storage Facility

International Nuclear Information System (INIS)

Kim, Geon Young; Kim, Kyung Su; Koh, Yong Kwon; Bae, Dae Seok; Park, Kyung Woo; Ji, Sung Hoon; Ryu, Ji Hoon

2009-08-01

Hydrological and geochemical analysis of the various kinds of water including observation borehole groundwater was carried out for the assessment of the hydrological safety of the underground oil storage cavern and the potentiality of mineralogical and microbiological clogging was estimated. There was no distinct chemical difference in the various kinds of water. All kinds of water are undersaturated with the calcite which is the major clogging mineral. Most water samples have low Fe and Mn concentrations. However, they are saturated or oversaturated with the iron-oxide/hydroxide minerals and have high dissolved oxygen contents which softiies the possibility of clogging by the iron-oxide/hydroxide minerals as a long-term aspect. Statistical analysis shows the degree of mineral precipitation or dissolution is mainly controlled by pH, Eh and DO of water samples. Because the slime forming bacteria ate dominant microbe in several observation boreholes, the clogging can be caused by it as a long-term aspect. In addition, the possibility of clogging can be increased if the microbial effect is combined with the mineralogical effect such as iron oxide/hydroxide minerals for the possibility of clogging. Therefore, the systematic and long-term program for the assessment of clogging is required for the safe operation of underground oil storage cavern

Paradigms of underground gas storage operation; Paradigmas del funcionamiento de un almacenamiento subterraneo de gas

Energy Technology Data Exchange (ETDEWEB)

Bonoris, Patricia; Vizcarra, Rodolfo; Buciak, Jorge [Companias Asociadas Petroleras S.A. (Argentina)

2004-07-01

The main objective of the study was to determine, for the underground storage of gas, the Current Useful Volume and Maximum Useful Current of operation, as well as have an acceptable interpretation that allows calculating the investment needed to reach this Maximum Usable Volume.

Extensive optimisation analyses of the piping of two large underground gas storage ariel compressors

NARCIS (Netherlands)

Eijk, A.; Korst, H.J.C.; Ploumen, G.; Heyer, D.

2007-01-01

Two large identical 6-cylinder Ariel JGB/6 compressors of each 7.5 Mw, are used for the underground gas storage (UGS) plant of Essent in Epe, Germany. The compressors can be operated at a wide range of operating conditions, e.g. variable suction and discharge pressures, 2-stage mode during gas

The French natural gas industry

International Nuclear Information System (INIS)

1999-01-01

This little folder summarizes in few pages the main economical data of the French natural gas industry: supplies according to the country of origin, length of transport and distribution networks, LNG tanker ship fleet, underground storage capacity, population of LNG-fueled vehicles, cogeneration installations, consumption by sectors and by industrial activities, LPG consumption, supplies, distribution and sales, LPG-fuel for vehicles, CO 2 and NO x releases, equipment of households. (J.S.)

DOE underground storage tank waste remediation chemical processing hazards. Part I: Technology dictionary

International Nuclear Information System (INIS)

DeMuth, S.F.

1996-10-01

This document has been prepared to aid in the development of Regulating guidelines for the Privatization of Hanford underground storage tank waste remediation. The document has been prepared it two parts to facilitate their preparation. Part II is the primary focus of this effort in that it describes the technical basis for established and potential chemical processing hazards associated with Underground Storage Tank (UST) nuclear waste remediation across the DOE complex. The established hazards involve those at Sites for which Safety Analysis Reviews (SARs) have already been prepared. Potential hazards are those involving technologies currently being developed for future applications. Part I of this document outlines the scope of Part II by briefly describing the established and potential technologies. In addition to providing the scope, Part I can be used as a technical introduction and bibliography for Regulatory personnel new to the UST waste remediation, and in particular Privatization effort. Part II of this document is not intended to provide examples of a SAR Hazards Analysis, but rather provide an intelligence gathering source for Regulatory personnel who must eventually evaluate the Privatization SAR Hazards Analysis

Using virtual objects to aid underground storage tank teleoperation

International Nuclear Information System (INIS)

Anderson, R.J.; Davies, B.

1994-01-01

In this paper we describe an algorithm by which obstructions and surface features in an underground storage tank can be modeled and used to generate virtual barrier function for a real-time telerobotic system, which provides an aid to the operator for both real-time obstacle avoidance and for surface tracking. The algorithm requires that the slave's tool and every object in the waste storage tank be decomposed into convex polyhedral primitives, with the waste surface modeled by triangular prisms. Intrusion distance and extraction vectors are then derived at every time step by applying Gilbert's polyhedra distance algorithm, which has been adapted for the task. This information is then used to determine the compression and location of nonlinear virtual spring-dampers whose total force is summed and applied to the manipulator/teleoperator system. Experimental results using a PUMA 560 and a simulated waste surface validate the approach, showing that it is possible to compute the algorithm and generate smooth, realistic pseudo forces for the teleoperator system using standard VME bus hardware

A GIS-based 3D online information system for underground energy storage in northern Germany

Science.gov (United States)

Nolde, Michael; Malte, Schwanebeck; Ehsan, Biniyaz; Rainer, Duttmann

2015-04-01

We would like to present the concept and current state of development of a GIS-based 3D online information system for underground energy storage. Its aim is to support the local authorities through pre-selection of possible sites for thermal, electrical and substantial underground energy storages. Since the extension of renewable energies has become legal requirement in Germany, the underground storing of superfluously produced green energy (such as during a heavy wind event) in the form of compressed air, gas or heated water has become increasingly important. However, the selection of suitable sites is a complex task. The presented information system uses data of geological features such as rock layers, salt domes and faults enriched with attribute data such as rock porosity and permeability. This information is combined with surface data of the existing energy infrastructure, such as locations of wind and biogas stations, powerline arrangement and cable capacity, and energy distribution stations. Furthermore, legal obligations such as protected areas on the surface and current underground mining permissions are used for the process of pre-selecting sites suitable for energy storage. Not only the current situation but also prospective scenarios, such as expected growth in produced amount of energy are incorporated in the system. While the process of pre-selection itself is completely automated, the user has full control of the weighting of the different factors via the web interface. The system is implemented as an online 3D server GIS environment, so that it can easily be utilized in any web browser. The results are visualized online as interactive 3d graphics. The information system is implemented in the Python programming language in combination with current Web standards, and is build using only free and open source software. It is being developed at Kiel University as part of the ANGUS+ project (lead by Prof. Sebastian Bauer) for the federal state of

30 CFR 75.1903 - Underground diesel fuel storage facilities and areas; construction and safety precautions.

Science.gov (United States)

2010-07-01

... areas; construction and safety precautions. 75.1903 Section 75.1903 Mineral Resources MINE SAFETY AND...; construction and safety precautions. (a) Permanent underground diesel fuel storage facilities must be— (1... with at least 240 pounds of rock dust and provided with two portable multipurpose dry chemical type...

Vienna: a capital transported by LPG

International Nuclear Information System (INIS)

Anon.

1996-01-01

For more than 30 years the Austrian capital has chosen the LPG-fuel for its public transportation systems. This choice was advised by the environmental necessity to reduce the emissions of particulates from diesel engines and by the economical will of having a competitive fuel source with respect to diesel fuel. This paper recalls first the historical evolution of Vienna's buses progressively equipped with dual-fuel engines, and since 1976 with LPG fuel engines only. Today's the LPG buses fleet represents about 80% of the Vienna Transport buses. Then, the economical (fuel consumption, investment, exploitation and maintenance costs) and environmental (particulates and CO emissions) balance-sheet of this evolution is analysed. Since 1988, the use of catalytic converters for exhaust systems has allowed a 80% reduction of NOx emissions. (J.S.)

The American Liquefied Petroleum Gases market (LPG)

International Nuclear Information System (INIS)

Myers, D.N.

1993-01-01

The United States is the leading LPG producer and consumer in the world: fuel applications are mainly in the form of propane, the fourth-ranked US source of energy. The US LPG industry serves more than 20 million customers, mainly on the residential, commercial and agricultural markets. 5 tabs., 6 photos

Underground Pumped Storage Hydropower using abandoned open pit mines: influence of groundwater seepage on the system efficiency

Science.gov (United States)

Pujades, Estanislao; Bodeux, Sarah; Orban, Philippe; Dassargues, Alain

2016-04-01

Pumped Storage Hydropower (PSH) plants can be used to manage the production of electrical energy according to the demand. These plants allow storing and generating electricity during low and high demand energy periods, respectively. Nevertheless, PSH plants require a determined topography because two reservoirs located at different heights are needed. At sites where PSH plants cannot be constructed due to topography requirements (flat regions), Underground Pumped Storage Hydropower (UPSH) plants can be used to adjust the electricity production. These plants consist in two reservoirs, the upper one is located at the surface (or at shallow depth) while the lower one is underground (or deeper). Abandoned open pit mines can be used as lower reservoirs but these are rarely isolated. As a consequence, UPSH plants will interact with surrounding aquifers exchanging groundwater. Groundwater seepage will modify hydraulic head inside the underground reservoir affecting global efficiency of the UPSH plant. The influence on the plant efficiency caused by the interaction between UPSH plants and aquifers will depend on the aquifer parameters, underground reservoir properties and pumping and injection characteristics. The alteration of the efficiency produced by the groundwater exchanges, which has not been previously considered, is now studied numerically. A set of numerical simulations are performed to establish in terms of efficiency the effects of groundwater exchanges and the optimum conditions to locate an UPSH plant.

Site-specific issues related to structural/seismic design of an underground independent spent fuel storage installation (ISFSI)

International Nuclear Information System (INIS)

Tripathi, B.P.

2005-01-01

Utilities owning and operating commercial nuclear power plants (NPP) in USA may choose to build an underground Independent Spent Fuel Storage Installation (ISFSI) to store the spent nuclear fuels. The regulatory requirements and other guidance are based on 10 CFR Part 72, Regulatory Guide RG 3.73, Standard Review Plans NUREG-1536 and NUREG-1567, and Interim staff Guidance (ISG) documents as applicable. Structures, Systems, and Components (SSCs) classified as important to safety are designed to withstand the effects of site-specific environmental conditions and natural phenomena such as earthquake, tornado, flood, etc. An underground ISFSI for storage of spent nuclear fuel, presents some unique analysis and design challenges. This paper will briefly address some of these challenges and discuss site-specific loads, including seismic for the ISFSI design. (authors)

Tank Waste Remediation System Inactive Miscellaneous Underground Storage Tanks Program Plan

International Nuclear Information System (INIS)

Gustavson, R.D.

1995-12-01

The Program Management Plan (PMP) describes the approach that will be used to manage the Tank Waste Remediation System (TWRS) Inactive Miscellaneous Underground Storage Tank (IMUST) Program. The plan describes management, technical, and administrative control systems that will be used to plan and control the IMUSTs Program performance. The technical data to determine the IMUSTs status for inclusion in the Single Shell Tank Farm Controlled Clean and Stable (CCS) Program. The second is to identify and implement surveillance, characterization, stabilization, and modifications to support CCS prior to final closure

LPG markets face upheaval as buyers press for change

International Nuclear Information System (INIS)

McDonald, Paul

1999-01-01

This article focuses on the system used for selling liquefied petroleum gas (LPG) where the sellers set the market price with Saudi Arabia dominating the market. The introduction and acceptance of a new method for setting the export price in relation to the spot price, the production of more LPG for export than forecast, the impact on the Saudi Arabian methyl tertiary butyl ether (MTBE) industry of California's banning MTBE additives to petrol,and the possibility of Asian buyers renegotiating the supply agreements are discussed. Details of Saudi Arabia's petrochemical plants planning to use LPG and world LPG production for 1998 are tabulated. The US market, and new systems for trading and pricing are considered. (UK)

Mines as lower reservoir of an UPSH (Underground Pumping Storage Hydroelectricity): groundwater impacts and feasibility

Science.gov (United States)

Bodeux, Sarah; Pujades, Estanislao; Orban, Philippe; Dassargues, Alain

2016-04-01

The energy framework is currently characterized by an expanding use of renewable sources. However, their intermittence could not afford a stable production according to the energy demand. Pumped Storage Hydroelectricity (PSH) is an efficient possibility to store and release electricity according to the demand needs. Because of the topographic and environmental constraints of classical PSH, new potential suitable sites are rare in countries whose topography is weak or with a high population density. Nevertheless, an innovative alternative is to construct Underground Pumped Storage Hydroelectricity (UPSH) plants by using old underground mine works as lower reservoir. In that configuration, large amount of pumped or injected water in the underground cavities would impact the groundwater system. A representative UPSH facility is used to numerically determine the interactions with surrounding aquifers Different scenarios with varying parameters (hydrogeological and lower reservoir characteristics, boundaries conditions and pumping/injection time-sequence) are computed. Analysis of the computed piezometric heads around the reservoir allows assessing the magnitude of aquifer response and the required time to achieve a mean pseudo-steady state under cyclic solicitations. The efficiency of the plant is also evaluated taking the leakage into the cavity into account. Combining these two outcomes, some criterions are identified to assess the feasibility of this type of projects within potential old mine sites from a hydrogeological point of view.

Cathode protection for underground steel tanks

International Nuclear Information System (INIS)

Angelovski, Zoran

1998-01-01

Cathodic protection of underground petroleum storage tanks and piping systems is acceptable for both economic and ecological reasons. With out the cathodic protection of underground steel reservoirs, short time after the exploitation, there was a bore as a result of underground corrosion. The bore causes ecological consequences and at the same time its repair needs big investments. Furthermore, there are great number of tanks placed near cities, so in the future this problem needs a special attention in order to preserve ecological surrounding. The topic of this paper is underground corrosion as well as cathodic protection of steel tanks for oil derivatives storage. (author)

Analysis of the vaporization of the liquefied gas of the petroleum (LPG) in tanks

International Nuclear Information System (INIS)

Alzate Espinosa, Guillermo A; Jaraba V, Xavier F

2005-01-01

Putting together thermodynamics (phase behavior), heat transfer and mass transfer fundamentals; it was possible to structure a mathematical and numerical model to simulate the vaporization process of LPG in tanks. The simulation model allows studying any feeding process with gaseous LPG to an appliance, and therefore, to follow changes inside the LPG tank related with LPG composition and its properties, temperature and pressure. A continuous or by cycles supplying process of gaseous LPG from a tank to any appliance promotes a reduction of liquid LPG temperature, an increase on specific gravity of LPG in both phases, and also an increasing in the value calorific of gaseous LPG

RANCANG BANGUN PROTOTYPE PENANGANAN DINI DAN PENDETEKSI KEBOCORAN LPG BERBASIS MIKROKONTROLER MELALUI SMS

OpenAIRE

Iksal, Iksal; Sumiati, Sumiati; Harizal, Harizal

2017-01-01

Masalah keamanan dalam pemakaian Gas LPG belakangan ini mendapat perhatian serius, banyak diberitakan terjadinya kebakaran akibat ledakan dari kebcoran Gas LPG. Mengingat mobilitas manusia semakin meningkat yang menuntut mereka tidak berada di dalam ruangan tempat penyimpanan Gas LPG untuk mengawasinya sepanjang waktu. Dibutuhkan sistem yang dapat memonitoring pemakaian Gas LPG secara realtime. Sehingga dapat meminimalisir tingkat kelalaian dalam terjadinya kebocoran Gas LPG.  Berdasarkan lat...

LPG diesel dual fuel engine – A critical review

Directory of Open Access Journals (Sweden)

B. Ashok

2015-06-01

Full Text Available The engine, which uses both conventional diesel fuel and LPG fuel, is referred to as ‘LPG–diesel dual fuel engines’. LPG dual fuel engines are modified diesel engines which use primary fuel as LPG and secondary fuel as diesel. LPG dual fuel engines have a good thermal efficiency at high output but the performance is less during part load conditions due to the poor utilization of charges. This problem can be overcome by varying factors such as pilot fuel quantity, injection timing, composition of the gaseous fuel and intake charge conditions, for improving the performance, combustion and emissions of dual fuel engines. This article reviews about the research work done by the researchers in order to improve the performance, combustion and emission parameters of a LPG–diesel dual fuel engines. From the studies it is shown that the use of LPG in diesel engine is one of the capable methods to reduce the PM and NOx emissions but at same time at part load condition there is a drop in efficiency and power output with respect to diesel operation.

Design and Performance of LPG Fuel Mixer for Dual Fuel Diesel Engine

Science.gov (United States)

Desrial; Saputro, W.; Garcia, P. P.

2018-05-01

Small horizontal diesel engines are commonly used for agricultural machinery, however, availability of diesel fuel become one of big problems especially in remote area. Conversely, in line with government policy for conversion of kerosene into LPG for cooking, then LPG become more popular and available even in remote area. Therefore, LPG is potential fuel to replace the shortage of diesel fuel for operating diesel engine in remote area. The purpose of this study was to design mixing device for using dual fuel i.e. LPG and diesel fuel and evaluate its performance accordingly. Simulation by using CFD was done in order to analyze mixture characteristics of LPG in air intake manifold. The performance test was done by varying the amount of LPG injected in intake air at 20%, 25%, 30%, 35%, until 40%, respectively. Result of CFD contour simulation showed the best combination when mixing 30% LPG into the intake air. Performance test of this research revealed that mixing LPG in air intake can reduce the diesel fuel consumption about 0.7 l/hour (without load) and 1.14 l/hour (with load). Diesel engine revolution increases almost 300 rpm faster than when using diesel fuel only. Based on economic analysis, using the fuel combination (diesel fuel – LPG) is not recommended in the area near SPBU where the price of diesel fuel is standard. However, using the fuel combination LPG-diesel fuel is highly recommended in the remote areas in Indonesia where price of diesel fuel is comparatively expensive which will provide cheaper total fuel cost for diesel engine operation.

Experimental analysis on a spark ignition petrol engine fuelled with LPG (liquefied petroleum gas)

International Nuclear Information System (INIS)

Masi, Massimo

2012-01-01

The use of LPG (liquefied petroleum gas) as alternative fuel to petrol is common practise in spark ignition engines. While the main driving force to the use of LPG still remains the low cost for the end user, its favourable pollutant emissions, in particular carbon dioxide, will in the middle term probably increase interest in LPG as an IC engine fuel. In addition, there are both theoretical and technical reasons to consider LPG as an attractive fuel also in terms of engine performance. Despite the continuously increasing stock production of dual-fuel (petrol–LPG) passenger car models, doubts still exist about both real engine performance in LPG operation and the reliability of the dual-fuel feeding system. This paper deals with the theoretical advantages of using LPG as fuel for SI engines. Brake performance tests of a passenger car engine fed with petrol and LPG are analysed and compared. The stock engine has been equipped with a “third-generation” standard kit for dual-fuel operation. The performance reductions in LPG operation are discussed in both steady state and transient condition. The results of some modifications to the set-up of both the petrol and LPG metering devices, designed for a better justification of the measured performance, are also presented. -- Highlights: ► Experimental research on the actual performances of an SI engine fed with petrol and gaseous LPG. ► Theoretical advantages and drawbacks of fuelling SI ICE’s with LPG. ► Brake performance analysis shows a noticeable gap between LPG and petrol operation. ► Local measurements confirm that the thermodynamic operation of the evaporator-pressure reducer device is crucial for the engine performance. ► The performance of the up-to-date kit for petrol–LPG dual-fuel operation is greatly affected by the settings of the mechanical components of the LPG evaporator device.

Robotic system for remote inspection of underground storage tanks

International Nuclear Information System (INIS)

Griebenow, B.L.; Martinson, L.M.

1990-01-01

Westinghouse Idaho Nuclear Company, Inc. (WINCO), operates the Idaho Chemical Processing Plant (ICPP) for the US Department of Energy (DOE). WINCO's mission is to process government owned spent nuclear fuel. The process involves dissolving the fuel and extracting off uranium. The waste from this process is temporarily stored at the ICPP in underground storage tanks. The tanks were put in service between 1953 and 1966 and are operating 10 to 15 years beyond their design life. Five of the tanks will be replaced by 1998. The integrity of the remaining six tanks must be verified to continue their use until they can be replaced at a later data. In order to verify the tank integrity, a complete corrosion analysis must be performed. This analysis will require a remote visual inspection of the tank surfaces

Control system design for robotic underground storage tank inspection systems

International Nuclear Information System (INIS)

Kiebel, G.R.

1994-09-01

Control and data acquisition systems for robotic inspection and surveillance systems used in nuclear waste applications must be capable, versatile, and adaptable to changing conditions. The nuclear waste remediation application is dynamic -- requirements change as public policy is constantly re-examined and refocused, and as technology in this area advances. Control and data acquisition systems must adapt to these changing conditions and be able to accommodate future missions, both predictable and unexpected. This paper describes the control and data acquisition system for the Light Duty Utility Arm (LDUA) System that is being developed for remote surveillance and inspection of underground storage tanks at the Hanford Site and other US Department of Energy (DOE) sites. It is a high-performance system which has been designed for future growth. The priority mission at the Hanford site is to retrieve the waste generated by 50 years of production from its present storage and process it for final disposal. The LDUA will help to gather information about the waste and the tanks it is stored in to better plan and execute the cleanup mission

Risk comparison of LPG and petrol vehicles in public car parks

NARCIS (Netherlands)

Molag, M.; Steen, M. van der

1998-01-01

LPG is generally considered as a clean fuel for cars in comparison with petrol. Although from an environmentally point of view LPG may be favoured, a further introduction of the use of the fuel is hindered by legislative measures. In some countries cars running on LPG are not allowed to enter public

Corrective Action Plan for Corrective Action Unit 135: Area 25 Underground Storage Tanks, Nevada Test Site, Nevada

International Nuclear Information System (INIS)

Cox, D. H.

2000-01-01

The Area 25 Underground Storage Tanks site Corrective Action Unit (CAU) 135 will be closed by unrestricted release decontamination and verification survey, in accordance with the Federal Facility Agreement and Consert Order (FFACO, 1996). The CAU includes one Corrective Action Site (CAS). The Area 25 Underground Storage Tanks, (CAS 25-02-01), referred to as the Engine-Maintenance Assembly and Disassembly (E-MAD) Waste Holdup Tanks and Vault, were used to receive liquid waste from all of the radioactive drains at the E-MAD Facility. Based on the results of the Corrective Action Investigation conducted in June 1999 discussed in the Corrective Action Investigation Plan for Corrective Action Unit 135: Area 25 Underground Storage Tanks, Nevada Test Site, Nevada (DOE/NV,1999a), one sample from the radiological survey of the concrete vault interior exceeded radionuclide preliminary action levels. The analytes from the sediment samples that exceeded the preliminary action levels are polychlorinated biphenyls, Resource Conservation and Recovery Act metals, total petroleum hydrocarbons as diesel-range organics, and radionuclides. Unrestricted release decontamination and verification involves removal of concrete and the cement-lined pump sump from the vault. After verification that the contamination has been removed, the vault will be repaired with concrete, as necessary. The radiological- and chemical-contaminated pump sump and concrete removed from the vault would be disposed of at the Area 5 Radioactive Waste Management Site. The vault interior will be field surveyed following removal of contaminated material to verify that unrestricted release criteria have been achieved

Corrective Action Plan for Corrective Action Unit 135: Area 25 Underground Storage Tanks, Nevada Test Site, Nevada

Energy Technology Data Exchange (ETDEWEB)

D. H. Cox

2000-07-01

The Area 25 Underground Storage Tanks site Corrective Action Unit (CAU) 135 will be closed by unrestricted release decontamination and verification survey, in accordance with the Federal Facility Agreement and Consert Order (FFACO, 1996). The CAU includes one Corrective Action Site (CAS). The Area 25 Underground Storage Tanks, (CAS 25-02-01), referred to as the Engine-Maintenance Assembly and Disassembly (E-MAD) Waste Holdup Tanks and Vault, were used to receive liquid waste from all of the radioactive drains at the E-MAD Facility. Based on the results of the Corrective Action Investigation conducted in June 1999 discussed in the Corrective Action Investigation Plan for Corrective Action Unit 135: Area 25 Underground Storage Tanks, Nevada Test Site, Nevada (DOE/NV,1999a), one sample from the radiological survey of the concrete vault interior exceeded radionuclide preliminary action levels. The analytes from the sediment samples that exceeded the preliminary action levels are polychlorinated biphenyls, Resource Conservation and Recovery Act metals, total petroleum hydrocarbons as diesel-range organics, and radionuclides. Unrestricted release decontamination and verification involves removal of concrete and the cement-lined pump sump from the vault. After verification that the contamination has been removed, the vault will be repaired with concrete, as necessary. The radiological- and chemical-contaminated pump sump and concrete removed from the vault would be disposed of at the Area 5 Radioactive Waste Management Site. The vault interior will be field surveyed following removal of contaminated material to verify that unrestricted release criteria have been achieved.

Performance and emissions of a heavy-duty diesel/LPG dual fuel engine

Energy Technology Data Exchange (ETDEWEB)

Schaberg, Paul [Sasol Technology, Cape Town (South Africa)

2013-06-01

This paper describes an investigation into the combustion characteristics and exhaust emissions of a heavy-duty truck engine which has been equipped with an aftermarket conversion kit to enable operation as a diesel/LPG (Liquefied Petroleum Gas) dual fuel engine. During operation diesel fuel is displaced by LPG which is vaporised and metered into the inlet manifold by means of solenoid injectors. It was found that, as the LPG fuelling rate is increased, the cylinder pressure rise rates and peak cylinder pressures increase, as do the carbon monoxide and unburned hydrocarbon emissions. At higher loads it was found that the LPG autoignites independently of the diesel fuel, resulting in very high rates of cylinder pressure rise. Particulate and nitrogen oxide emissions remain largely unchanged, and carbon dioxide emissions are reduced due to the lower carbon content of the LPG fuel. Different LPG compositions were also investigated and it was found that the LPG properties that have the most significant effect on combustion and emissions were the autoignition and volatility characteristics. (orig.)

Report from SG 1.2: use of 3-D seismic data in exploration, production and underground storage

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

The objective of this study was to investigate the experience gained from using 3D and 4D techniques in exploration, production and underground storage. The use of 3D seismic data is increasing and considerable progress in the application of such data has been achieved in recent years. 3D is now in extensive use in exploration, field and storage development planning and reservoir management. By using 4D (or time-lapse) seismic data from a given producing area, it is also possible to monitor gas movement as a function of time in a gas field or storage. This emerging technique is therefore very useful in reservoir management, in order to obtain increased recovery, higher production, and to reduce the risk of infill wells. These techniques can also be used for monitoring underground gas storage. The study gives recommendations on the use of 3D and 4D seismic in the gas industry. For this purpose, three specific questionnaires were proposed: the first one dedicated to exploration, development and production of gas fields (Production questionnaire), the second one dedicated to gas storages (Storage questionnaire) and the third one dedicated to the servicing companies. The main results are: - The benefit from 3D is clear for both producing and storage operators in improving structural shape, fault pattern and reservoir knowledge. The method usually saves wells and improve gas volume management. - 4D seismic is an emerging technique with high potential benefits for producers. Research in 4D must focus on the integration of seismic methodology and interpretation of results with production measurements in reservoir models. (author)

Impact of transportation and distribution factors on LPG supplies and prices

Energy Technology Data Exchange (ETDEWEB)

Aprea, G

1980-01-01

A predicted world LPG surplus of 14-20 million tons/y in the 1980's will not be absorbed even by the US and Japan, which are now the largest LPG consumers, unless market prices and return on investments are favorable enough to justify the investments required for the associated transportation and distribution facilities for new uses for LPG, e.g., as petrochemical feedstock, heating fuel, automotive fuel, or feedstock for the manufacture of high-octane additives. For the petrochemical industry, this implies new technologies and investments to optimize the equilibrium of the plants in connection with the market demand for ethylene, propylene, butadiene, and aromatic feedstocks. World LPG trade should rise from 13 million tons in 1979 to 40 million tons by 1985, of which 17 million tons will be moved on the Japanese captive market, up from about 10 million tons in 1979. The increased use of LPG in 1979 already boosted freight rates, which made shipowners consider new tonnage investment. The need for long-term supplier-user agreements as to LPG supplies and prices is discussed.

Underground storage of radioactive wastes

International Nuclear Information System (INIS)

Dietz, D.N.

1977-01-01

An introductory survey of the underground disposal of radioactive wastes is given. Attention is paid to various types of radioactive wastes varying from low to highly active materials, as well as mining techniques and salt deposits

Development of road hydronic snow-ice melting system with solar energy and seasonal underground thermal energy storage

Energy Technology Data Exchange (ETDEWEB)

Gao, Q.; Liu, Y.; Ma, C.Q.; Li, M.; Huang, Y.; Yu, M. [Jilin Univ., Changchun (China). Dept. of Thermal Energy Engineering; Liu, X.B. [Climate Master Inc., OK (United States)

2008-07-01

Snow and ice melting technologies that used thermal energy storage were explored. The study included analyses of solar heat slab, seasonal underground thermal energy storage, and embedded pipe technologies. Different road materials, roadbed construction methods, and underground rock and soil conditions were also discussed. New processes combining all 3 of the main technologies were also reviewed. Other thermal ice melting technologies included conductive concrete and asphalt; heating cables, and hydronic melting systems. Geothermal energy is increasingly being considered as a means of melting snow and ice from roads and other infrastructure. Researchers have also been focusing on simulating heat transfer in solar collectors and road-embedded pipes. Demonstration projects in Japan, Switzerland, and Poland are exploring the use of combined geothermal and solar energy processes to remove snow and ice from roads. Research on hydronic melting technologies is also being conducted in the United States. The study demonstrated that snow-ice melting energy storage systems will become an important and sustainable method of snow and ice removal in the future. The technology efficiently uses renewable energy sources, and provides a cost-effective means of replacing or reducing chemical melting agents. 33 refs., 1 fig.

Study on underground gas storage in Europe and Central Asia; Etude sur le stockage souterrain du gaz en Europe et en Asie Centrale

Energy Technology Data Exchange (ETDEWEB)

Sedlacek, R. [NlfB, Germany (Germany); Rott, W. [Wintershall AG, Celle (Germany); Rokosz, W. [POGC, Poland (PL)] (and others)

2000-07-01

The Working Party on Gas of the United Nations Economic Commission for Europe (UN/ECE), at its sixth session in 1996, decided to undertake a study on 'Underground gas storage in Europe and Central Asia'. The study was launched by the Working Party on Gas in the recognition of the role of underground gas storage (UGS) in the creation of unified European gas market, its liberalization, security of gas supply and cooperation among gas enterprises. The data analysed by the study was collected through the comprehensive questionnaire, circulated among gas companies/organizations of the ECE member-countries. To carry out the study, a special Ad Hoc Group of Experts, representing leading gas companies of the region, was set up. The study deals with a wide range of issues related to the underground storage of gas, such as current status of UGS in Europe and Central Asia, new and emerging technologies, new and existing UGS projects, regulatory framework, cost of storage in USA and in Europe, future gas markets development. An attempt was also made to identify the UGS facilities that play (and could provide in the future) the international contract border services. (authors)

Asia, North America lead way in growth of NGL, LPG trade

International Nuclear Information System (INIS)

Otto, K.; Gist, R.; Whitley, C.; Haun, R.

1998-01-01

Recent analyses of world NGL trade indicate that important changes in LPG supply and demand are under way in Asia and North America. LPG markets in the 1990s reflect a rapidly shifting balance between East-of-Suez and West-of-Suez markets. This shift has increased concern about availability of future LPG supplies for Asia. The paper discusses world developments, East versus West of Suez, end uses and supplies in Asia, Canadian ethane, propane, butane, and natural gasoline, Mexican ethane, LPG, and natural gasoline, US ethane, propane, butanes, and iso-C 4 and C 5

LPG Dependence after a Suicide Attempt

Directory of Open Access Journals (Sweden)

Ebru Aldemir

2015-01-01

Full Text Available Inhalant abuse is a problem that is getting more common all around the world. The increase in prevalence of inhalant abuse escalates morbidity and mortality rates. About 22% of people using inhalant have died at their first attempt. Particularly propane, butane, or propane-butane mixture has highest mortality rates. Sudden sniffing death syndrome, cardiomyopathy, central nervous system toxicity, hematological abnormalities, kidney toxicity, and hepatocellular toxicities are the major complications of inhalant abuse. Herein we present a patient with inhalant use disorder. At the age of 19, after a stressful life event he had unsuccessfully tried to suicide by inhaling LPG (liquefied petroleum gas, a mixture of butane and propane gases. After he realized that he had hallucinations and felt better during the inhalation, he started to abuse it. He was addicted to LPG for 10 years at the time of admission. Besides being dangerous for the society security, this intense level of LPG inhalation (12 liters a day not giving any physical harm makes this case interesting.

Co-firing used engine lubrication oil with LPG in furnaces

International Nuclear Information System (INIS)

Al-Omari, S.A.-B.; Shaheen, A.; Al Fakhr, A.; Al-Hosani, A.; Al Yahyai, M.

2010-01-01

Combustion and heat transfer characteristics obtained based co-firing LPG with used engine oils (UEO) in a furnace, are investigated experimentally. In an attempt to assess UEO as a fuel, the UEO-based results are compared with results obtained using two other fuels, namely diesel, and a used cooking oil (UCkO). To ease its admission to the furnace and its subsequent vaporization and combustion, UEO is preheated by allowing it to flow upwardly in a vertical pipe surrounded by hot gases generated from LPG combustion. UEO that reaches the tip of the pipe un-vaporized, spills and hence has the chance to further heatup and vaporize as it exchanges heat with the upwardly flowing LPG combustion gases, in a counter flow process. Runs are divided into three groups based on the mass ratio of the liquid-fuel/LPG and the mass flow rate of the LPG supplied to the furnace. Ranges of these quantities over which UEO qualify as a good fuel and/or good promoter to radiation have been identified.

Co-firing used engine lubrication oil with LPG in furnaces

Energy Technology Data Exchange (ETDEWEB)

Al-Omari, S.A.-B.; Shaheen, A.; Al Fakhr, A.; Al-Hosani, A.; Al Yahyai, M. [Mechanical Engineering Department, UAE University, Al-Ain (United Arab Emirates)

2010-06-15

Combustion and heat transfer characteristics obtained based co-firing LPG with used engine oils (UEO) in a furnace, are investigated experimentally. In an attempt to assess UEO as a fuel, the UEO-based results are compared with results obtained using two other fuels, namely diesel, and a used cooking oil (UCkO). To ease its admission to the furnace and its subsequent vaporization and combustion, UEO is preheated by allowing it to flow upwardly in a vertical pipe surrounded by hot gases generated from LPG combustion. UEO that reaches the tip of the pipe un-vaporized, spills and hence has the chance to further heatup and vaporize as it exchanges heat with the upwardly flowing LPG combustion gases, in a counter flow process. Runs are divided into three groups based on the mass ratio of the liquid-fuel/LPG and the mass flow rate of the LPG supplied to the furnace. Ranges of these quantities over which UEO qualify as a good fuel and/or good promoter to radiation have been identified. (author)

A comparative analysis of liquefied petroleum gas (LPG) and kerosene related burns.

Science.gov (United States)

Ahuja, Rajeev B; Dash, Jayant K; Shrivastava, Prabhat

2011-12-01

Previous studies from our department reflected a trend of decreasing incidence of burns culminating from rising income levels, which were bringing about a change in the cooking fuel in many urban households [1,2]. These studies also indicated a changing scenario of increased incidence of burns from LPG mishaps [2]. In the absence of much information on the subject we felt it rather imperative to comparatively study the pattern of burn injuries resulting from LPG and kerosene. This prospective study was conducted on the clinical database of consecutive patients admitted with burns sustained due to LPG and kerosene from 1st January 2009 to 31st May 2010 (17 months). Data recorded for each patient included; age, gender, religion, socioeconomic status, literacy level, type of family unit, marital status, type of dwelling unit, mode of injury and its exact mechanism, place of incident, level of cooking stove, extent of burns (%TBSA), presence of features of inhalation injury, number of patients affected in a single mishap, size of LPG cylinder used, length of hospital stay and mortality. Of 731 flame burn patients in this study, 395 (54%) were due to kerosene burns and 200 (27.4%) from LPG mishaps. Significantly, the majority of injuries, in both the groups, occurred in lower middle class families living as nuclear units, in a single room dwelling, without a separate kitchen. Majority of LPG burns (70.5%, 141 patients) resulted from a gas leak and 25.5% were from cooking negligence (51 patients). 50.5% of kerosene accidents were from 'stove mishaps' and 49% due to cooking negligence. In all kerosene accidents the stove was kept at floor level but in LPG group 20.6% had the stove placed on a platform. There was a slight difference in mean TBSA burns; 51% in kerosene group compared to 41.5% TBSA in LPG group. There were nine episodes in LPG group in which there were more than three burn victims admitted for treatment. Very importantly, 77% patients in LPG group were from

Feasibility studies for pump and treat technology at leaking underground storage tank sites in Michigan

International Nuclear Information System (INIS)

O'Brien, J.M.; Pekas, B.S.

1993-01-01

Releases from underground storage tanks have resulted in impacts to groundwater at thousands of sites across the US. Investigations of these sites were initiated on a national basis with the implementation of federal laws that became effective December 22, 1989 (40 CFR 280). Completion of these investigations has led to a wave of design and installation of pump and treat aquifer restoration systems where impacts to groundwater have been confirmed. The purpose of this paper is to provide managers with a demonstration of some of the techniques that can be used by the consulting industry in evaluating the feasibility of pump and treat systems. With knowledge of these tools, managers can better evaluate proposals for system design and their cost effectiveness. To evaluate the effectiveness of typical pump and treat systems for leaking underground storage tank (LUST) sites in Michigan, ten sites where remedial design had been completed were randomly chosen for review. From these ten, two sites were selected that represented the greatest contrast in the types of site conditions encountered. A release of gasoline at Site 1 resulted in contamination of groundwater and soil with benzene, toluene, ethylbenzene, and xylenes

Geochemistry research planning for the underground storage of high-level nuclear waste

International Nuclear Information System (INIS)

Apps, J.A.

1983-09-01

This report is a preliminary attempt to plan a comprehensive program of geochemistry research aimed at resolving problems connected with the underground storage of high-level nuclear waste. The problems and research needs were identified in a companion report to this one. The research needs were taken as a point of departure and developed into a series of proposed projects with estimated manpowers and durations. The scope of the proposed research is based on consideration of an underground repository as a multiple barrier system. However, the program logic and organization reflect conventional strategies for resolving technological problems. The projects were scheduled and the duration of the program, critical path projects and distribution of manpower determined for both full and minimal programs. The proposed research was then compared with ongoing research within DOE, NRC and elsewhere to identify omissions in current research. Various options were considered for altering the scope of the program, and hence its cost and effectiveness. Finally, recommendations were made for dealing with omissions and uncertainties arising from program implementation. 11 references, 6 figures, 4 tables

Relevance of deep-subsurface microbiology for underground gas storage and geothermal energy production.

Science.gov (United States)

Gniese, Claudia; Bombach, Petra; Rakoczy, Jana; Hoth, Nils; Schlömann, Michael; Richnow, Hans-Hermann; Krüger, Martin

2014-01-01

This chapter gives the reader an introduction into the microbiology of deep geological systems with a special focus on potential geobiotechnological applications and respective risk assessments. It has been known for decades that microbial activity is responsible for the degradation or conversion of hydrocarbons in oil, gas, and coal reservoirs. These processes occur in the absence of oxygen, a typical characteristic of such deep ecosystems. The understanding of the responsible microbial processes and their environmental regulation is not only of great scientific interest. It also has substantial economic and social relevance, inasmuch as these processes directly or indirectly affect the quantity and quality of the stored oil or gas. As outlined in the following chapter, in addition to the conventional hydrocarbons, new interest in such deep subsurface systems is rising for different technological developments. These are introduced together with related geomicrobiological topics. The capture and long-termed storage of large amounts of carbon dioxide, carbon capture and storage (CCS), for example, in depleted oil and gas reservoirs, is considered to be an important options to mitigate greenhouse gas emissions and global warming. On the other hand, the increasing contribution of energy from natural and renewable sources, such as wind, solar, geothermal energy, or biogas production leads to an increasing interest in underground storage of renewable energies. Energy carriers, that is, biogas, methane, or hydrogen, are often produced in a nonconstant manner and renewable energy may be produced at some distance from the place where it is needed. Therefore, storing the energy after its conversion to methane or hydrogen in porous reservoirs or salt caverns is extensively discussed. All these developments create new research fields and challenges for microbiologists and geobiotechnologists. As a basis for respective future work, we introduce the three major topics, that is

LPG based all plastic pressure sensor

DEFF Research Database (Denmark)

Bundalo, Ivan-Lazar; Lwin, R.; Leon-Saval, S.

2015-01-01

A prototype all-plastic pressure sensor is presented and characterized for potential use as an endoscope. The sensor is based on Long Period Gratings (LPG) inscribed with a CO2 laser in 6-ring microstructured PMMA fiber. Through a latex coated, plastic 3D-printed transducer pod, external pressure...... is converted to longitudinal elongation of the pod and therefore of the fiber containing the LPG. The sensor has been characterised for pressures of up to 160 mBar in an in-house built pressure chamber. Furthermore, the influence of the fiber prestrain, fiber thickness and the effect of different glues...

Power and LPG production with LNG import

International Nuclear Information System (INIS)

Mak, J.Y.

2004-01-01

When used in power cogeneration, Liquefied Natural Gas (LNG) is both energy efficient and can eliminate seawater or fuel gas consumption as well as the associated environmental impacts of conventional regasification processes. However, some liquefied natural gas (LNG) sources have heating values higher than current North American natural gas pipelines can allow for. LNG from these cannot be injected into gas pipelines without several heating control processing steps. This paper outlines two new technologies developed to address this issue. The first is a power cogeneration process using LNG as a heat sink. The second technology involves a fractionation process removing Liquid Propane Gas (LPG) components from imported LNG, thereby controlling heat value. Both technologies are applicable in grassroots installations as well as being suitable for retrofitting to existing LNG regasification for power generation and LPG production. It was concluded that power cogeneration with a mixed fluid power cycle recovered a significant portion of energy in LNG liquefaction plants. Additionally, it was also possible to fractionate high quality LPG from LNG at a low cost, with the residue being further re-condensed and re-utilized for power generation. It was also concluded that the LNG fractionation process would add flexibility to the LNG receiving terminals, allowing the import of lower quality LNG to North America, while also generating additional revenues from LPG production. 3 refs., 5 tabs., 6 figs

Underground gas storage Uelsen: Findings from planning, building and commissioning. Part 1: Deposit; Untertagegasspeicher Uelsen: Erkenntnisse aus Planung, Bau und Inbetriebnahme. Teil 1: Lagerstaette

Energy Technology Data Exchange (ETDEWEB)

Wallbrecht, J.; Beckmann, H.; Reiser, H.; Wilhelm, R. [BEB Erdgas und Erdoel GmbH, Hannover (Germany)

1998-12-31

The underground gas storage at Uelsen which was built as a H-gas storage in a former variegated sandstone gasfield in Western Lower Saxony close to the town of Nordhorn has added to the gas supply system of the BEB Erdgas and Erdoel GmbH. The underground storage is connected to the Bunde-Rheine transport pipeline BEB-grid gas system by a 27 km pipeline and is a consequent expansion of BEB`s underground storage/transport system. Planning, building and commissioning were handled by BEB. Findings to date are described. [Deutsch] Der Untertagegasspeicher (UGS) Uelsen, der in einem ehemaligen Buntsandstein Gasfeld im westlichen Niedersachsen in der Naehe der Stadt Nordhorn als H-Gasspeicher eingerichtet wurde, hat die BEB Erdgas und Erdoel GmbH eine weitere Staerkung ihres Gasversorgungssystems erreicht. Der UGS Uelsen ist ueber eine 27 km lange Anbindungsleitung mit der zum BEB - Ferngasleitungssystems gehoerenden Bunde-Rheine Transportleitung verbunden und stellt eine konsequente Erweiterung des BEB Untertagegasspeicher-/Transportsystems dar. Planung, Bau und Inbetriebnahme erfolgten durch BEB im Rahmen einer integrierten bereichsuebergreifenden Projektbearbeitung. Die hierbei gewonnenen Erkenntnisse werden im Folgenden fuer den Untertagebereich dargestellt. (orig.)

Advanced remediation, technology development in the underground storage tank

International Nuclear Information System (INIS)

Gates, T.E.; Gilchrist, R.L.

1992-01-01

Production of nuclear materials has been a major mission of the U. S. Department of Energy (DOE) over the last 50 years. These activities have contributed to a substantial accumulation of hazardous, radioactive, and mixed wastes. In 1989, the DOE established the Office of Environmental Restoration and Waste Management. This office coordinates and manages the DOE's remediation, waste minimization, and environmental compliance activities. It also has responsibility for waste generated by current operations. Within this office is the Office of Technology Development, which is responsible for providing technology improvements. This paper reports on integrated demonstrations which have been established to efficiently bring the best technologies to bear on the common needs of multiple DOE sites. One such need is resolution of the actions required for final closure and waste disposal of liquid (including sludge and salt cake) radioactive and chemical wastes that have been transferred to underground storage tanks

Analisa Pembuatan Tabung Gas Lpg 3 Kg

Directory of Open Access Journals (Sweden)

Mustafa -

2012-11-01

Full Text Available Program konversi minyak tanah ke LPG merupakan program pemerintah yang bertujuan untuk mengurangisubsidi BBM, dengan mengalihkan pemakaian minyak tanah ke LPG. Tujuan analisa untuk mengetahui proses pembuatantabung gas, proses deep drawing dan metode pengelasan yang baik. Karena masih banyak orang yang takut memakai bahanbakar LPG tersebut karena takut meledak akibat kualitasnya yang kurang bagus. Deep Drawing atau biasa disebut drawingadalah salah satu jenis proses pembentukan logam, dimana bentuk pada umumnya berupa silinder dan selalu mempunyaikedalaman tertentu. Pada proses pembuatan tabung gas elpiji untuk mendisain suatu proses pembentukan logam , sepertipenarikan (drawing. Salah satu pekerjaan yang harus kita lakukan adalah menentukan atau memilih kapasitas mesin(energi, gaya, torsi serta perkakas dan peralatan yang akan digunakan untuk proses tersebut. Pada proses deep drawingdengan kecepatan tekan yang telah ditentukan (sesuai tabel daya tekan maksimal tidak boleh melebihi: 167,330 kg. Padaproses pengelasan circum, tegangan normal mencapai 61.16 kg/cm2, karena masih diatas uji ketahanan hidrostastik, makamasih dalam batas aman.

Designing a Prototype LPG Injection Electronic Control Unit for a Carburetted Gasoline Engine

Directory of Open Access Journals (Sweden)

Barış ERKUŞ

2015-07-01

Full Text Available In this study, the originally carburetted gasoline engine was converted to gas-phase liquefied petroleum gas (LPG injection engine by using an after market LPG conversion kit's components except the electronic control unit (ECU. Instead of after market LPG injection ECU, the ECU which was designed considering the effects of  electromagnetic interference (EMI, was used for controlling injection. The designed ECU was tested in terms of EMI while the engine was being run and it was detected that the EMI noises could be suppressed as possible by taken measures. Designed ECU was used in performance tests at different engine conditions and the results obtained with LPG injection were compared with the results obtained with LPG carburetion. According to the performance test results, LPG injection ECU designed in this study could help to achieve low exhaust emissions and high engine performance.  

Development of in-structure design spectra for dome mounted equipment on underground waste storage tanks at the Hanford Site

International Nuclear Information System (INIS)

Julyk, L.J.

1995-09-01

In-structure response spectra for dome mounted equipment on underground waste storage tanks at the Hanford Site are developed on the basis of recent soil-structure-interaction analyses. Recommended design spectra are provided for various locations on the tank dome

Dual-fuel HCCI operation with DME/LPG/gasoline/hydrogen

International Nuclear Information System (INIS)

Bae, C.

2009-01-01

The advantages of homogeneous charge compression ignition (HCCI) engines include usage of the different type of fuels, ultra low nitrogen oxide and particulate matter emissions and improved fuel economy. Disadvantages include an excessive combustion rate, engine noise, and hydrocarbon and carbon emissions. An experiment on dual-fuel HCCI operation with dimethyl ether (DME)/liquefied petroleum gas (LPG)/gasoline/hydrogen was presented. The advantages and disadvantages were first presented and the dual-fuel HCCI combustion engine was illustrated through an experimental apparatus. The experimental conditions were also presented in terms of engine speed, DME injection quantity, LPC injection quantity, and LPC composition. Experimental results were discussed for output performance and indicated mean effective pressure (IMEP). It was concluded that the effect of LPG composition in a DME-LPG dual-fueled HCCI engine at various injection quantity and injective timing were observed. Specifically, it was found that propane was a more effective way to increase IMEP in this study, and that in a DME HCCI engine, higher load limit was extended by using LPG as an ignition inhibitor. tabs., figs.

France: freeing the block on auto Lpg

International Nuclear Information System (INIS)

Anon.

1995-01-01

Can it be hoped, when business starts again this september, that the right conditions will finally exist for LPG motor car fuel in France to get off the ground ? In any case the context seems to lend itself to that end more so than in previous years. Perhaps because measures in favour of a tax incentive - tirelessly sought by the LPG industry with the backing of a large car manufacturer and the support of the 'technical' ministers - have met with powerful trends this time, backed up by public opinion worried at the levels of atmospheric pollution reached in July and August. Perhaps too because all the main players in the sector are ready to rise to the challenge: equipment suppliers offer new, high-performance materials, a manufacturer of Renault's declares itself convinced of the advantages of LPG fuel, while distributors of the product declare themselves ready to accompany tax exemption with an effort regarding tax-free pricing. As elected representatives and societies (one on behalf of the users of LPG, the other for the protection of the environment) have shown equally their support, the components are nearly all assembled. One should guard against premature optimism, however: only the draft finance law for 1996, presented in the Council of Ministers around the 20th September, will tell if the Finance ministry shows itself aware of the arguments put forward. (authors). 3 figs., 1 tab

Influence of H2O2 on LPG fuel performance evaluation

International Nuclear Information System (INIS)

Khan, Muhammad Saad; Ahmed, Iqbal; Mutalib, Mohammad Ibrahim bin Abdul; Nadeem, Saad; Ali, Shahid

2014-01-01

The objective of this mode of combustion is to insertion of hydrogen peroxide (H 2 O 2 ) to the Liquefied Petroleum Gas (LPG) combustion on spark plug ignition engines. The addition of hydrogen peroxide may probably decrease the formation of NO x , CO x and unburned hydrocarbons. Hypothetically, Studies have shown that addition of hydrogen peroxide to examine the performance of LPG/H 2 O 2 mixture in numerous volumetric compositions starting from lean LPG until obtaining a better composition can reduce the LPG fuel consumption. The theory behind this idea is that, the addition of H 2 O 2 can cover the lean operation limit, increase the lean burn ability, diminution the burn duration along with controlling the exhaust emission by significantly reducing the greenhouse gaseous

Advice on Sustainable Use of the Underground for Heat and Cold Storage; Advies Duurzaam Gebruik van de Bodem voor WKO

Energy Technology Data Exchange (ETDEWEB)

Oomes, J.

2009-09-15

Insights and ideas are given and discussed with regard to sustainable use of soil and underground for heat and cold storage. Also attention is paid to the marginal conditions for the application of heat and cold storage [Dutch] Inzichten en ideeen worden gegeven en besproken over duurzaam gebruik van de bodem voor warmte- koudeopslag (WKO). Daarnaast worden ook de randvoorwaarden van WKO in kaart gebracht.

Environmental payoffs of LPG cooking in India

Science.gov (United States)

Singh, D.; Pachauri, S.; Zerriffi, H.

2017-11-01

Over two-thirds of Indians use solid fuels to meet daily cooking energy needs, with associated negative environmental, social, and health impacts. Major national initiatives implemented by the Indian government over the last few decades have included subsidies for cleaner burning fuels like liquid petroleum gas (LPG) and kerosene to encourage a transition to these. However, the extent to which these programs have affected net emissions from the use of these improved fuels has not been adequately studied. Here, we estimate the amount of fuelwood displaced and its net emissions impact due to improved access to LPG for cooking in India between 2001 and 2011 using nationally representative household expenditure surveys and census datasets. We account for a suite of climate-relevant emissions (Kyoto gases and other short-lived climate pollutants) and biomass renewability scenarios (a fully renewable and a conservative non-renewable case). We estimate that the national fuelwood displaced due to increased LPG access between 2001 and 2011 was approximately 7.2 million tons. On aggregate, we estimate a net emissions reduction of 6.73 MtCO2e due to the fuelwood displaced from increased access to LPG, when both Kyoto and non-Kyoto climate-active emissions are accounted for and assuming 0.3 as the fraction of non-renewable biomass (fNRB) harvested. However, if only Kyoto gases are considered, we estimate a smaller net emissions decrease of 0.03 MtCO2e (assuming fully renewable biomass harvesting), or 3.05 MtCO2e (assuming 0.3 as the fNRB). We conclude that the transition to LPG cooking in India reduced pressures on forests and achieved modest climate benefits, though uncertainties regarding the extent of non-renewable biomass harvesting and suite of climate-active emissions included in such an estimation can significantly influence results in any given year and should be considered carefully in any analysis and policy-making.

The worldwide market will not be short of LPG fuels

International Nuclear Information System (INIS)

Anon.

1998-01-01

This paper is a synthesis of an internal note of the French Butane and Propane Committee (CFBP) about the perspectives of the worldwide market of LPG fuels. The conclusion of this study is that the market will not be short of LPG, in particular the French market and the automotive fuels. The consumption of LPG fuels for vehicles in France is growing up rapidly (about 100% in 1997 with respect to 1996: 90000 t consumed in 1997 by 70000 vehicles) and the resource remains important and can reach 3 millions of tons per year. (J.S.)

Remote inspection of underground storage tanks

International Nuclear Information System (INIS)

Griebenow, B.L.; Martinson, L.M.

1992-01-01

Westinghouse Idaho Nuclear Company, Inc. (WINCO) operates the Idaho Chemical Processing Plant (ICPP) for the US Department of Energy. The ICPP's mission is to process government-owned spent nuclear fuel. The process involves dissolving the fuel, extracting off uranium, and calcining the waste to a solid form for storage, Prior to calcining, WINCO temporarily stores the liquid waste from this process in eleven 1,135,600-l(300,000-gal), 15,2-m (50-ft)-diam, high-level liquid waste tanks. Each of these stainless steel tanks is contained within an underground concrete vault. The only access to the interior of the tanks is through risers that extend from ground level to the dome of the tanks. WINCO is replacing these tanks because of their age and the fact that they do not meet all of the current design requirements. The tanks will be replaced in two phases. WINCO is now in the Title I design stage for four new tank and vault systems to replace five of the existing systems. The integrity of the six remaining tanks must be verified to continue their use until they can be replaced in the second phase. To perform any integrity analysis, the inner surface of the tanks must be inspected. The remote tank inspection (RTI) robotic system, designed by RedZone Robotics of Pittsburgh, Pennsylvania, was developed to access the interior of the tanks and position various end effectors required to perform tank wall inspections

Underground Storage Alternative To Nigeria's Gas Flaring

International Nuclear Information System (INIS)

Obi, A.I

2004-01-01

Energy demands are increasing as the world's population of energy users grows. At the same time many nations want to decommission nuclear plants in support of a cleaner environment. Clean burning natural gas is the fuel most likely to meet society's complex requirements. Demand for natural gas will rise more strongly than for any fossil fuel. The utilization of the huge gas resources form the petroleum deposit in the Niger Delta area is the major problem confronting the oil/gas industry in Nigeria and the disposal of associated gas has been a major challenge for the barrel of oil; hence with oil production of about 2.0 million barrels per day, some 2.0 billion standard cubic feet of AG is producing everyday. An alarming proportion of the gas is wasted by flaring, while very small proportion is used by oil-producing companies and other most alarming rate of flaring in the world compared with other oil/gas producing countries. This paper highlights the numerous benefits accruing from proper utilization of natural gas using SASOL of South Africa as an example and recommends underground storage of natural gas as an industry that will help check flaring, meet fluctuating demand and create wealth for the nation

Acoustic imaging of underground storage tank wastes

International Nuclear Information System (INIS)

Mech, S.J.

1995-09-01

Acoustics is a potential tool to determine the properties of high level wastes stored in Underground Storage Tanks. Some acoustic properties were successfully measured by a limited demonstration conducted in 114-TX. This accomplishment provides the basis for expanded efforts to qualify techniques which depend on the acoustic properties of tank wastes. This work is being sponsored by the Department of Energy under the Office of Science and Technology. In FY-1994, limited Tank Waste Remediation Systems EM-30 support was available at Hanford and Los Alamos National Laboratory. The Massachusetts Institute of Technology (MIT) and Earth Resources Laboratory (ERL) were engaged for analysis support, and Elohi Geophysics, Inc. for seismic testing services. Westinghouse-Hanford Company provided the testing and training, supplied the special engineering and safety analysis equipment and procedures, and provided the trained operators for the actual tank operations. On 11/9/94, limited in-tank tests were successfully conducted in tank 114-TX. This stabilized Single Shell Tank was reported as containing 16.8 feet of waste, the lower 6.28 feet of which contained interstitial liquid. Testing was conducted over the lower 12 feet, between two Liquid Observation Wells thirty feet apart. The ''quick-look'' data was reviewed on-site by MIT and Elohi

Poitiers and automotive LPG; Poitiers: la municipalite et le district croient au GPL carburant

Energy Technology Data Exchange (ETDEWEB)

Anon.

1999-04-01

Looking for a reduction in its fuel expenses and a reduction in urban air pollution, Poitiers' local authorities ordered 15 LPG fuelled vehicles some 20 years ago. They ran solely with LPG. Today, some 115 vehicles, including two machines for floor cleaning, one for preparation of skating rings and a forklift, run on LPG. These last machines expected, all vehicles can run on LPG or gasoline. (authors)

Deteksi Kebocoran Gas LPG Menggunakan Detektor Arduino dengan Algoritma Fuzzy Logic Mandani

OpenAIRE

Hakim, Lukman; Yonatan, Vidi

2017-01-01

Bencana kebakaran yang diakibatkan oleh kebocoran gas LPG (Liquid  Petroleum   Gas) mengalami kenaikan setiap tahun dari tahun 2011 sampai 2015 diantaranya 17% diakibatkan oleh kebocoran gas. Penggunaan detektor kebocoran gas LPG menggunakan arduino yang dilengkapi sensor gas dan suhu memberikan kemudahan untuk deteksi secara awal terjadinya kebocoran dan kebakaran. Perancangan detektor kebocoran gas LPG menggunakan algoritma fuzzy logic mandani, dilengkapi dengan informasi mel...

NUMERICAL STUDY ON COOLING EFFECT POTENTIAL FROM VAPORIZER DEVICE OF LPG VEHICLE

Directory of Open Access Journals (Sweden)

MUJI SETIYO

2017-07-01

Full Text Available Over fuel consumption and increased exhaust gas due to the A/C system have become a serious problem. On the other hand, the LPG-fueled vehicle provides potential cooling from LPG phase changes in the vaporizer. Therefore, this article presents the potential cooling effect calculation from 1998 cm3 spark ignition (SI engine. A numerical study is used to calculate the potential heat absorption of latent and sensible heat transfer during LPG is expanded in the vaporizer. Various LPG compositions are also simulated through the engine speed range from 1000 to 6000 rpm. The result shows that the 1998 cm3 engine capable of generating the potential cooling effect of about 1.0 kW at 1000 rpm and a maximum of up to 1.8 kW at 5600 rpm. The potential cooling effects from the LPG vaporizer contributes about 26% to the A/C system works on eco-driving condition.

Deteksi Kebocoran Gas LPG Menggunakan Detektor Arduino dengan Algoritma Fuzzy Logic Mandani

OpenAIRE

Lukman Hakim; Vidi Yonatan

2017-01-01

Bencana kebakaran yang diakibatkan oleh kebocoran gas LPG (Liquid  Petroleum   Gas) mengalami kenaikan setiap tahun dari tahun 2011 sampai 2015 diantaranya 17% diakibatkan oleh kebocoran gas. Penggunaan detektor kebocoran gas LPG menggunakan arduino yang dilengkapi sensor gas dan suhu memberikan kemudahan untuk deteksi secara awal terjadinya kebocoran dan kebakaran. Perancangan detektor kebocoran gas LPG menggunakan algoritma fuzzy logic mandani, dilengkapi dengan informasi melalui Short Mess...

Fire safety of LPG in marine transportation. Final report

Energy Technology Data Exchange (ETDEWEB)

Martinsen, W.E.; Johnson, D.W.; Welker, J.R.

1980-06-01

This report contains an analytical examination of cargo spill and fire hazard potential associated with the marine handling of liquefied petroleum gas (LPG) as cargo. Principal emphasis was on cargo transfer operations for ships unloading at receiving terminals, and barges loading or unloading at a terminal. Major safety systems, including emergency shutdown systems, hazard detection systems, and fire extinguishment and control systems were included in the analysis. Spill probabilities were obtained from fault tree analyses utilizing composite LPG tank ship and barge designs. Failure rates for hardware in the analyses were generally taken from historical data on similar generic classes of hardware, there being very little historical data on the specific items involved. Potential consequences of cargo spills of various sizes are discussed and compared to actual LPG vapor cloud incidents. The usefulness of hazard mitigation systems (particularly dry chemical fire extinguishers and water spray systems) in controlling the hazards posed by LPG spills and spill fires is also discussed. The analysis estimates the probability of fatality for a terminal operator is about 10/sup -6/ to 10/sup -5/ per cargo transfer operation. The probability of fatality for the general public is substantially less.

Deteksi Kebocoran Gas LPG Menggunakan Detektor Arduino dengan Algoritma Fuzzy Logic Mandani

Directory of Open Access Journals (Sweden)

Lukman Hakim

2017-10-01

Full Text Available Bencana kebakaran yang diakibatkan oleh kebocoran gas LPG (Liquid  Petroleum   Gas mengalami kenaikan setiap tahun dari tahun 2011 sampai 2015 diantaranya 17% diakibatkan oleh kebocoran gas. Penggunaan detektor kebocoran gas LPG menggunakan arduino yang dilengkapi sensor gas dan suhu memberikan kemudahan untuk deteksi secara awal terjadinya kebocoran dan kebakaran. Perancangan detektor kebocoran gas LPG menggunakan algoritma fuzzy logic mandani, dilengkapi dengan informasi melalui Short Message Service (SMS dan Buzzer. Detektor kebocoran gas LPG dapat melakukan indikasi terjadinya bocor pada konsentrasi gas rata-rata 456 ppm dari 10 pengujian dan indikasi api merah 23,30 dapat mengenal terjadinya kebakaran, detektor mengirimkan SMS kepada pemilik rumah dan pemadam kebakaran.

French Committee of Butane and Propane. 2015 activity report. Butane, propane, LPG - Immediately available solutions for the future

International Nuclear Information System (INIS)

2016-05-01

This document presents the 2015 highlights of the French LPG fuels industry: 1 - 2015 LPG market; 2 - CFBP missions and 2015 highlights: promotion of LPG industry and uses, contribution to standards development, safety of industrial sites, promoting LPG specificities, safety of LPG transports and training, ensuring clients' installations safety, promoting LPG in the energy mix, promoting LPGc potential, public information

About working of the research program on development of underground space of Russia

International Nuclear Information System (INIS)

Kartoziya, B.A.

1995-01-01

Basic proposition relative to the developed federal program on scientific research in the area of assimilating underground space in Russia are presented. The underground objects are divided by their purpose into four groups: 1) underground objects of house-hold purpose (energy and mining complex, industrial enterprises, storages, garages, etc); 2) underground objects of social purpose (libraries, shops, restaurants, etc); 3) underground objects of ecological purpose (storages, disposal sites for radioactive wastes and hazardous substances, dangerous productions, etc); 4) underground objects of defense purpose. Trends in the scientific-research program formation, relative to underground space assimilation are enumerated. 7 refs

GlidArc-assisted production of synthesis gas from LPG (Propane)

International Nuclear Information System (INIS)

Czernichowski, A.; Czernichowski, P.; Czernichowski, M.

2003-01-01

Small and medium size reformers that run on widely available Liquefied Petroleum Gas (LPG, containing mostly the propane) can provide Synthesis Gas (or Hydrogen extracted from it) to some Fuel Cell powered cars, boats, homes, farms etc. reducing therefore costs of the pure Hydrogen distribution. We contribute to such idea realization through our simply, plasma-assisted reformer avoiding a need of poison resistant catalysts or prior LPG desulfurizer. In fact, any level of sulphur in LPG is accepted for our non-catalytic reformer based on high-voltage discharges (called GlidArc). The discharges catalytically assist the exothermic partial oxidation process. Electric power assistance is less than 2% of the Lower Heating Value (LHV) of produced SynGas. Recycling such a small portion of the energy is therefore an acceptable compromise. The unique oxidant source is air. This contribution presents our expanded tests with commercial LPG in a 1-L reactor working at atmospheric pressure. At a 0.1 kW electric power assistance we produce a Nitrogen-diluted SynGas containing up to 45% of H 2 +CO at the output flow rate corresponding up to 2.7 m 3 (n)/h of pure H 2 +CO mixture that is equivalent to LHV output power of 8.6 kW. The LPG is totally reformed at more than 70% energetic efficiency and at the total absence of soot. (author)

Study of Vapour Cloud Explosion Impact from Pressure Changes in the Liquefied Petroleum Gas Sphere Tank Storage Leakage

Science.gov (United States)

Rashid, Z. A.; Suhaimi Yeong, A. F. Mohd; Alias, A. B.; Ahmad, M. A.; AbdulBari Ali, S.

2018-05-01

This research was carried out to determine the risk impact of Liquefied Petroleum Gas (LPG) storage facilities, especially in the event of LPG tank explosion. In order to prevent the LPG tank explosion from occurring, it is important to decide the most suitable operating condition for the LPG tank itself, as the explosion of LPG tank could affect and cause extensive damage to the surrounding. The explosion of LPG tank usually occurs due to the rise of pressure in the tank. Thus, in this research, a method called Planas-Cuchi was applied to determine the Peak Side-On Overpressure (Po) of the LPG tank during the occurrence of explosion. Thermodynamic properties of saturated propane, (C3H8) have been chosen as a reference and basis of calculation to determine the parameters such as Explosion Energy (E), Equivalent Mass of TNT (WTNT), and Scaled Overpressure (PS ). A cylindrical LPG tank in Feyzin Refinery, France was selected as a case study in this research and at the end of this research, the most suitable operating pressure of the LPG tank was determined.

3rd Sino-German Conference “Underground Storage of CO2 and Energy”

CERN Document Server

Xie, Heping; Were, Patrick

2013-01-01

Anthropogenic greenhouse gas emissions, energy security and sustainability are three of the greatest contemporary global challenges today. This year the Sino-German Cooperation Group “Underground Storage of CO2 and Energy”, is meeting on the 21-23 May 2013 for the second time in Goslar, Germany, to convene its 3rd Sino-German conference on the theme “Clean Energy Systems in the Subsurface: Production, Storage and Conversion”.   This volume is a collection of diverse quality scientific works from different perspectives elucidating on the current developments in CO2 geologic sequestration research to reduce greenhouse emissions including measures to monitor surface leakage, groundwater quality and the integrity of caprock, while ensuring a sufficient supply of clean energy. The contributions herein have been structured into 6 major thematic research themes: Integrated Energy and Environmental Utilization of Geo-reservoirs: Law, Risk Management & Monitoring CO2 for Enhanced Gas and Oil Recovery, Coa...

Energy poverty reduction by fuel switching. Impact evaluation of the LPG conversion program in Indonesia

International Nuclear Information System (INIS)

Andadari, Roos Kities; Mulder, Peter; Rietveld, Piet

2014-01-01

In low- and middle-income countries, Liquefied Petroleum Gas (LPG) can be an attractive alternative to the widespread use of traditional kerosene. Not only is LPG a relatively clean, safe and cost-effective fuel for households, its large-scale adoption also reduces the heavy burden of kerosene consumption subsidies on government budgets. Against this background, we evaluate the impact of a large government program to substitute LPG for kerosene in Indonesia. Using a household survey across urban, suburban and rural regions we find that this program was very effective in causing a large scale shift from kerosene to LPG. This shift was positively influenced by level of education, household size and household income. Contradicting the energy-ladder model, the LPG program, reinforced by an increase in the price of kerosene, led to increased stacking of fuels, including increasing consumption of both electricity and traditional biomass. In addition, our analysis shows that the LPG program failed to substantially reduce the overall number of energy-poor people, but it has been effective in alleviating extreme energy-poverty. Finally, we find that medium and higher income households in suburban areas benefitted most from the LPG program. - Highlights: • Impact evaluation of a government program to substitute LPG for kerosene in Indonesia. • The program caused a large scale shift from kerosene to LPG. • Contradicting the energy-ladder model, the program led to increased stacking of fuels. • The program did not substantially reduce overall energy poverty, but alleviated extreme energy-poverty. • Medium and higher income households in suburban areas benefitted most from the LPG program

A Feasibility Study on LPG as Marine Fuel; En foerstudie paa gasol som marint braensle

Energy Technology Data Exchange (ETDEWEB)

Kjartansson, Sveinbjoern

2012-06-15

With the upcoming stricter emission rules fast approaching and the requirements for higher quality fuel, it is inevitable that there will be a change of fuel from HFO to cleaner options. These changes are driven by the knowledge of the health problems associated with emissions from ships in coastal areas. One viable option for meeting these demands for reduced emission is to utilize LPG as a marine fuel. This thesis investigates the harmful chemicals that are present in the exhaust gases, followed by an introduction on LPG as marine fuel. Transport options for LPG and existing engine technology is presented and the feasibility of LPG as a fuel option on the European / Swedish market is studied. The conclusion from this study is that sufficient infrastructure for distribution of LPG is in place to serve potential marine market demand. Engine technology for using LPG as fuel has been developed for a wide range of power outputs. The economic incentive in the fuel price difference alone is likely to attract ship owners to invest in LPG fueled fleets.

Explosion hazards of LPG-air mixtures in vented enclosure with obstacles.

Science.gov (United States)

Zhang, Qi; Wang, Yaxing; Lian, Zhen

2017-07-15

Numerical simulations were performed to study explosion characteristics of liquefied petroleum gas (LPG) explosion in enclosure with a vent. Unlike explosion overpressure and dynamic pressure, explosion temperature of the LPG-air mixture at a given concentration in a vented enclosure has very little variation with obstacle numbers for a given blockage ratio. For an enclosure without obstacle, explosion overpressures for the stoichiometric mixtures and the fuel-lean mixtures reach their maximum within the vent and that for fuel-rich mixture reaches its maximum beyond and near the vent. Dynamic pressures produced by an indoor LPG explosion reach their maximum always beyond the vent no matter obstacles are present or not in the enclosure. A LPG explosion in a vented enclosure with built-in obstacles is strong enough to make the brick and mortar wall with a thickness of 370mm damaged. If there is no obstacle in the enclosure, the lower explosion pressure of several kPa can not break the brick and mortar wall with a thickness of 370mm. For a LPG explosion produced in an enclosure with a vent, main hazards, within the vent, are overpressure and high temperature. However main hazards are dynamic pressure, blast wind, and high temperature beyond the vent. Copyright © 2017 Elsevier B.V. All rights reserved.

Comparison of Performance Characteristics of LPG and Gasoline - Fuelled Single Cylinder SI Engine

Directory of Open Access Journals (Sweden)

Saad Abdul Qadir Abdul Azeez

2016-07-01

Full Text Available The investigations have been concentrated on decreasing fuel consumption by using alternative fuels and on lowering the concentration of toxic  components in combustion products. LPG as an alternative to gasoline  has  emerged  as  a  solution  to  the  deteriorating  urban  air  quality  problem,  especially  in  an  oil country like Iraq. LPG has already been used as cooking fuel in Iraq. In the present paper  practical tests of various operating parameters and concerns have been prepared for better understanding of operating conditions and constrains for a LPG fueled internal combustion engine.The results show that HUCR for gasoline was 8:1, and for LPG was 10:1. bsfc reduced by using LPG at its HUCR, while at CR=8:1 it became higher than that for gasoline. Volumetric efficiency reduced by using  LPG  due  to  its  gaseous  nature,  but  it  was  improved  when  the  engine  was  run  at  HUCR.  Brake thermal efficiency depends  on bsfc and bp, so LPG preceded gasoline at medium speeds and torques. Exhaust gas temperatures reduced by using LPG, the minimum values were when the engine operated at CR= 8:1. The maximum values were for gasoline share.

Root cause analysis of the fatigue failures of the pulsation dampers of a large underground gas storage (UGS) system

NARCIS (Netherlands)

Eijk, A.; Lange, D. de; Maljaars, J.; Tenbrock-Ingenhorst, A.; Gottmer, A.

2014-01-01

Two large identical 6-cylinder Ariel JGB/6 reciprocating compressors each of 7.5 MW, are used for an underground gas storage system (UGS) plant of RWE Gasspeicher GmbH located in Epe, Germany. The system is in operation since 2005. In 2011 several internals parts (baffle plates and baffle choke

A risk-based approach to prioritize underground storage tanks

International Nuclear Information System (INIS)

Chidambariah, V.; Travis, C.C.; Trabalka, J.R.; Thomas, J.K.

1992-01-01

The purpose of this paper is to present a risk-based approach for rapid prioritization of low level liquid radioactive waste underground storage tanks (LLLW USTs) for possible interim corrective measures and/or ultimate closure. The ranking of LLLW USTs is needed to ensure that tanks with the greatest potential for adverse impact on the environment and human health receive top priority for further evaluation and remediation. Wastes from the LLLW USTs at the Oak Ridge National Laboratory (ORNL) were pumped out at the time the tanks were removed from service. The residual liquids and sludge contain a mixture of radionuclides and chemicals. Contaminants of concern that were identified in the liquid phase of the inactive LLLW USTs include, the radionuclides, 9O Sr, 137 Cs and 233 U and the chemicals, carbon tetrachloride, trichloroethene, tetrachloroethene, methyl ethyl ketone, mercury, lead and chromium. The risk-based approach for prioritization of the LLLW USTs is based upon three major criteria: (1) leaking characteristics of the tank; (2) location of the tanks; and (3) toxic potential of the tank contents

CFBP and LPG market in 2004

International Nuclear Information System (INIS)

Anon.

2005-01-01

The French butane and propane committee (CFBP) has presented its activities in liquefied petroleum gases in its 2004 annual report. The success of its initiatives of promotion during the year 2004 has led the CFBP to launch a new campaign of advertisement since January 31, 2005. In its report, the CFBP stresses on the re-start up of the LPG fuel market. The sales of propane gas in tanks have raised by 5.2% between 2003 and 2004. The decay of the traditional market of gas cylinders has been practically stopped thanks to the sales dynamism of small (5-6 kg) cylinders and to the innovations added by some retailers on the 13 kg cylinders (level indicator). The sales of automotive LPG fuels have shown a slower decay during 2004. (J.S.)

LPG fuels in France in 1997

International Nuclear Information System (INIS)

Anon.

1998-01-01

This short note gives a statement of the sales of butane, propane and LPG fuels in France during the year 1997. Details are given for conditioned butane and propane products, cylinders and fixed reservoirs. (J.S.)

33 CFR 127.313 - Bulk storage.

Science.gov (United States)

2010-07-01

...) WATERFRONT FACILITIES WATERFRONT FACILITIES HANDLING LIQUEFIED NATURAL GAS AND LIQUEFIED HAZARDOUS GAS Waterfront Facilities Handling Liquefied Natural Gas Operations § 127.313 Bulk storage. (a) The operator...: (1) LNG. (2) LPG. (3) Vessel fuel. (4) Oily waste from vessels. (5) Solvents, lubricants, paints, and...

Recent developments with ALIBI, a model for site specific prediction of LPG tank BLEVE frequency

Energy Technology Data Exchange (ETDEWEB)

Goose, M.H. [Health and Safety Executive, Bootle (United Kingdom). Major Hazards Assessment Unit

1995-12-31

The concept behind the ALIBI model was first introduced to a technical audience in 1988 at the European Seminar on the Pressurised Storage of Flammable Liquids in London. Since that time it has been developed by SRD (now AEA Technology Consultancy Services) on behalf of HSE (MHAU). Although the structure of the model has remained largely unchanged, efforts have been made to refine the modelling within it. The main effort in refining the modelling has been with the response of LPG tanks to jet flame impingement, and this is described in the paper. (author)

Challenges to and proposals for underground gas storage (UGS business in China

Directory of Open Access Journals (Sweden)

Gangxiong Zhang

2017-05-01

Full Text Available Underground gas storage (UGS is one of the major storage and peak-shaving means in the world among numerous storage ways via gas fields, small-scale LNG, etc. With the rapid development of natural gas industry in China, the seasonal peak-shaving issues are increasingly prominent, so how to achieve sustainable development of UGS business has become a major problem at present. In view of this, we studied the present status and trend of UGS development abroad and analyzed the following challenges encountered by UGS in China. (1 UGS construction falls behind the world and peak-shaving capacity is insufficient. (2 There is lack of quality gas sources for storage and the complicated geological conditions make the cost of UGS construction high. (3 UGS construction is still at the preliminary stage, so experience is not enough in safety and scientific operation and management. (4 UGS construction, management and operation are not unified as a whole, so its maximum efficiency fails to be exerted. (5 The economic benefit of UGS is difficult to be shown without independent cost accounting. Based on the experience of other countries, some proposals were put forward on UGS development under the actual present situation: to strengthen strategic UGS layout, intensify storage site screening in key areas and steadily promote UGS construction; to establish professional UGS technical and management teams and intensify the research of key technologies; and to set up a complete and rationally-distributed UGS construction, operation and management system.

Cooking Fuels in Lagos, Nigeria: Factors Associated with Household Choice of Kerosene or Liquefied Petroleum Gas (LPG).

Science.gov (United States)

Ozoh, Obianuju B; Okwor, Tochi J; Adetona, Olorunfemi; Akinkugbe, Ayesha O; Amadi, Casmir E; Esezobor, Christopher; Adeyeye, Olufunke O; Ojo, Oluwafemi; Nwude, Vivian N; Mortimer, Kevin

2018-03-31

Cooking with dirty-burning fuels is associated with health risk from household air pollution. We assessed the prevalence of and factors associated with the use of cooking fuels, and attitudes and barriers towards use of liquefied petroleum gas (LPG). This was a cross-sectional, population-based survey conducted in 519 households in Lagos, Nigeria. We used a structured questionnaire to obtain information regarding choice of household cooking fuel and the attitudes towards the use of LPG. Kerosene was the most frequently used cooking fuel ( n = 475, 91.5%; primary use n = 364, 70.1%) followed by charcoal ( n = 159, 30.6%; primary use n = 88, 17%) and LPG ( n = 86, 16.6%; primary use n = 63, 12.1%). Higher level of education, higher income and younger age were associated with LPG vs. kerosene use. Fuel expenditure on LPG was significantly lower than for kerosene ( N (Naira) 2169.0 ± 1507.0 vs. N 2581.6 ± 1407.5). Over 90% of non-LPG users were willing to switch to LPG but cited safety issues and high cost as potential barriers to switching. Our findings suggest that misinformation and beliefs regarding benefits, safety and cost of LPG are important barriers to LPG use. An educational intervention program could be a cost-effective approach to improve LPG adoption and should be formally addressed through a well-designed community-based intervention study.

Spark Ignition LPG for Hydrogen Gas Combustion the Reduction Furnace ME-11 Process

International Nuclear Information System (INIS)

Achmad Suntoro

2007-01-01

Reverse engineering method for automatic spark-ignition system of LPG to burn hydrogen gaseous in the reducing process of ME-11 furnace has been successfully implemented using local materials. A qualitative study to the initial behaviour of the LPG flame system has created an idea by modification to install an automatic spark-ignition of the LPG on the reducing furnace ME-11. The automatic spark-ignition system has been tested and proved working well. (author)

Acoustic imaging of underground storage tank wastes: A feasibility study. Final report

International Nuclear Information System (INIS)

Turpening, R.; Zhu, Z.; Caravana, C.; Matarese, J.

1995-01-01

The objectives for this underground storage tank (UST) imaging investigation are: (1) to assess the feasibility of using acoustic methods in UST wastes, if shown to be feasible, develop and assess imaging strategies; (2) to assess the validity of using chemical simulants for the development of acoustic methods and equipment. This investigation examined the velocity of surrogates, both salt cake and sludge surrogates. In addition collected seismic cross well data in a real tank (114-TX) on the Hanford Reservation. Lastly, drawing on the knowledge of the simulants and the estimates of the velocities of the waste in tank 114-TX the authors generated a hypothetical model of waste in a tank and showed that non-linear travel time tomographic imaging would faithfully image that stratigraphy

A GIS Based 3D Online Decision Assistance System for Underground Energy Storage in Northern Germany

Science.gov (United States)

Nolde, M.; Schwanebeck, M.; Biniyaz, E.; Duttmann, R.

2014-12-01

We would like to present a GIS-based 3D online decision assistance system for underground energy storage. Its aim is to support the local land use planning authorities through pre-selection of possible sites for thermal, electrical and substantial underground energy storages. Since the extension of renewable energies has become legal requirement in Germany, the underground storing of superfluously produced green energy (such as during a heavy wind event) in the form of compressed air, gas or heated water has become increasingly important. However, the selection of suitable sites is a complex task. The assistance system uses data of geological features such as rock layers, salt caverns and faults enriched with attribute data such as rock porosity and permeability. This information is combined with surface data of the existing energy infrastructure, such as locations of wind and biogas stations, power line arrangement and cable capacity, and energy distribution stations. Furthermore, legal obligations such as protected areas on the surface and current underground mining permissions are used for the decision finding process. Not only the current situation but also prospective scenarios, such as expected growth in produced amount of energy are incorporated in the system. The decision process is carried out via the 'Analytic Hierarchy Process' (AHP) methodology of the 'Multi Object Decision Making' (MODM) approach. While the process itself is completely automated, the user has full control of the weighting of the different factors via the web interface. The system is implemented as an online 3D server GIS environment, with no software needed to be installed on the user side. The results are visualized as interactive 3d graphics. The implementation of the assistance system is based exclusively on free and open source software, and utilizes the 'Python' programming language in combination with current web technologies, such as 'HTML5', 'CSS3' and 'JavaScript'. It is

Safety issue resolution strategy plan for inactive miscellaneous underground storage tanks

International Nuclear Information System (INIS)

Wang, O.S.; Powers, T.B.

1994-09-01

The purpose of this strategy plan is to identify, confirm, and resolve safely issues associated with inactive miscellaneous underground storage tanks (MUSTs) using a risk-based priority approach. Assumptions and processes to assess potential risks and operational concerns are documented in this report. Safety issue priorities are ranked based on a number of considerations including risk ranking and cost effectiveness. This plan specifies work scope and recommends schedules for activities related to resolving safety issues, such as collecting historical data, searching for authorization documents, performing Unreviewed Safety Question (USQ) screening and evaluation, identifying safety issues, imposing operational controls and monitoring, characterizing waste contents, mitigating and resolving safety issues, and fulfilling other remediation requirements consistent with the overall Tank Waste Remediation System strategy. Recommendations for characterization and remediation are also recommended according to the order of importance and practical programmatic consideration

Simulation for thermal response of a spherical LPG tank; Kyukei LPG chozo tanku no netsuoto kaiseki

Energy Technology Data Exchange (ETDEWEB)

Chen, Hsi-jen; Lin, Mann-hsing; Chao, Fu-yuan [Tamkang University, Tamsui (Taiwan). Department of Chemical Engineering

1999-03-05

Liquefied petroleum gas (LPG) is a very important fuel and chemical feed stock as well; however, the hydrocarbon has been involved in many major fires and explosions. One of these accidents is boiling-liquid, expanding-vapor explosion (BLEVE). It is a phenomenon that results from the sudden release from confinement of a liquid at a temperature above its atmospheric-pressure boiling point. The sudden decrease in pressure results in the explosive vaporization of a fraction of the liquid and a cloud of vapor and mist with the accompanying blast effects. Most BLEVEs involve flammable liquids, and most BLEVE releases are ignited by a surrounding fire and result in a fireball. The primary objective of this paper is to develop a computer model in order to determine the thermal response of a spherical LPG tank involved in fire engulfment accidents. The assessment of the safety spacing between tanks was also discussed. (author)

Sistem Monitoring Pendeteksi Kebocoran LPG berbasis Mikrokontroller ATmega16 menggunakan RF APC220

Directory of Open Access Journals (Sweden)

RATNA SUSANA

2016-02-01

Full Text Available Abstrak Penggunaan LPG sebagai bahan bakar alternatif pengganti bahan bakar minyak dirasakan lebih efektif dan praktis. Namun kandungan senyawa di dalamnya memiliki efek yang negatif jika menguap di udara bebas. Sistem detektor gas LPG dapat menjadi salah satu solusi untuk mengetahui lebih dini terjadinya kebocoran gas. Implementasi sistem detektor gas LPG pada penelitian ini berupa sistem monitoring nirkabel yang dilengkapi alarm sebagai indikasi jika terjadi kebocoran gas. Sistem terdiri dari bagian Remote Controller dan Master Controller. Remote Controller menggunakan mikrokontroler ATMega16 yang terintegrasi dengan sensor MQ5, LCD dan transceiver RF APC220. Sedangkan Master Controller berupa komputer (PC yang dapat menampilkan kondisi ruangan yang dideteksi oleh bagian Remote Controller. Sistem berhasil mendeteksi gas LPG dan menampilkan kadar konsentrasinya dalam rentang 200 sampai dengan 1000 ppm. Ketika kadar konsentrasi gas mencapai 5000 ppm, alarm aktif secara otomatis dan memberikan status waspada. Pengiriman data secara nirkabel dengan adanya sejumlah penghalang berhasil dilakukan sampai jarak 200 m. Kata kunci: Sistem Monitoring, Remote Controller, Master Controller, LPG, RF APC220   Abstract The use of LPG as a fuel alternative to fossil fuels may be more effective and practical. Neverfluless its compound has a negative effect if it evaporates to the air. LPG gas detector system may be one solution to determine the early occurrence of gas leak. The detector system implementation in this study was a wireless monitoring system that had alarm to indicate if there was the gas leak. The system consisted of the Remote Controller and the Master Controller. Remote Controller used ATmega16 microcontroller integrated with MQ5 sensor, LCD and RF transceiver APC220. While the Master Controller in the form of a computer (PC that could display a room condition was detected by the Remote Controller section. LPG gas system successfully detected

Cooking Fuels in Lagos, Nigeria: Factors Associated with Household Choice of Kerosene or Liquefied Petroleum Gas (LPG

Directory of Open Access Journals (Sweden)

Obianuju B. Ozoh

2018-03-01

Full Text Available Cooking with dirty-burning fuels is associated with health risk from household air pollution. We assessed the prevalence of and factors associated with the use of cooking fuels, and attitudes and barriers towards use of liquefied petroleum gas (LPG. This was a cross-sectional, population-based survey conducted in 519 households in Lagos, Nigeria. We used a structured questionnaire to obtain information regarding choice of household cooking fuel and the attitudes towards the use of LPG. Kerosene was the most frequently used cooking fuel (n = 475, 91.5%; primary use n = 364, 70.1% followed by charcoal (n = 159, 30.6%; primary use n = 88, 17% and LPG (n = 86, 16.6%; primary use n = 63, 12.1%. Higher level of education, higher income and younger age were associated with LPG vs. kerosene use. Fuel expenditure on LPG was significantly lower than for kerosene ( N (Naira 2169.0 ± 1507.0 vs. N 2581.6 ± 1407.5. Over 90% of non-LPG users were willing to switch to LPG but cited safety issues and high cost as potential barriers to switching. Our findings suggest that misinformation and beliefs regarding benefits, safety and cost of LPG are important barriers to LPG use. An educational intervention program could be a cost-effective approach to improve LPG adoption and should be formally addressed through a well-designed community-based intervention study.

Recent progress of the waste processing and disposal projects within the Underground Storage Tank-Integrated Demonstration

International Nuclear Information System (INIS)

Hunt, R.D.; McGinnis, C.P.; Cruse, J.M.

1994-01-01

The US Department of Energy (DOE) Office of Environmental Restoration and Waste Remediation has created the Office of Technology Development (OTD) to provide new and improved remediation technologies for the 1 x 10 8 gal of radioactive waste in the underground storage tanks (USTs) at five DOE sites. The OTD established and the Underground Storage Tank-Integrated Demonstration (UST-ID) to perform demonstrations, tests, and evaluations on these new technologies before these processes are transferred to the tank sites for use in full-scale remediation of the USTs. The UST-ID projects are performed by the Characterization and Waste Retrieval Program or the Waste Processing and Disposal Program (WPDP). During FY 1994, the WPDP is funding 12 projects in the areas of supernate processing, sludge processing, nitrate destruction, and final waste forms. The supernate projects are primarily concerned with cesium removal. A mobile evaporator and concentrator for cesium-free supernate is also being demonstrated. The sludge projects are emphasizing sludge dissolution and the evaluation of the TRUEX and diamide solvent extraction processes for transuranic waste streams. One WPDP project is examining both supernate and sludge processes in an effort to develop a system-level plan for handling all UST waste. The other WPDP studies are concerned with nitrate and organic destruction as well as subsequent waste forms. The current status of these WPDP projects is presented

Kecamatan Tampan oleh Dinas Perindustrian dan Perdagangan Kota Pekanbaru (Studi Kasus: Pangkalan Lpg 3 Kg)

OpenAIRE

Faisal, Andini; Yuliani, Febri

2015-01-01

LPG 3 kg has become a very important requirement. It can be seen from the demand for LPG 3 kg is increasing every year, both in use for households or for the development of micro enterprises. The purpose of this research was to determine how the LPG 3 kg distribution control in the Kelurahan Sidomulyo Barat Kecamatan Tampan by the Department of Industry and Trade of Pekanbaru City (case study: Sub Distributor LPG 3 kg) and to determine the factors that affect the control in the distribution o...

Analisis Pengaruh Konsentrasi Gas LPG Menggunakan Sensor TGS 2610 Berbasis Mikrokontroler AVR ATMega8535

OpenAIRE

Nurhalimah

2011-01-01

Telah dilakukan analisis kuantitatif gas dalam LPG. Penelitian ini dilakukan untuk mengukur konsentrasi gas LPG terhadap sensor. Metoda yang digunakan untuk mengukur konsentrasi gas LPG yaitu sensor gas semikonduktor jenis TGS 2610 keluaran Figaro yang digunakan untuk mendeteksi keberadaan gas. Sementara yang menjadi pusat pengendalian dari seluruh alat yang dirancang digunakan mikrokontroler AVR ATMega8535. Selain itu sistem yang dirancang dilengkapi LCD sebagai tampilan nilai konsentrasi ga...

Differential Impact of LPG-and PG-Deficient Leishmania major Mutants on the Immune Response of Human Dendritic Cells.

Directory of Open Access Journals (Sweden)

Michelle A Favila

2015-12-01

Full Text Available Leishmania major infection induces robust interleukin-12 (IL12 production in human dendritic cells (hDC, ultimately resulting in Th1-mediated immunity and clinical resolution. The surface of Leishmania parasites is covered in a dense glycocalyx consisting of primarily lipophosphoglycan (LPG and other phosphoglycan-containing molecules (PGs, making these glycoconjugates the likely pathogen-associated molecular patterns (PAMPS responsible for IL12 induction.Here we explored the role of parasite glycoconjugates on the hDC IL12 response by generating L. major Friedlin V1 mutants defective in LPG alone, (FV1 lpg1-, or generally deficient for all PGs, (FV1 lpg2-. Infection with metacyclic, infective stage, L. major or purified LPG induced high levels of IL12B subunit gene transcripts in hDCs, which was abrogated with FV1 lpg1- infections. In contrast, hDC infections with FV1 lpg2- displayed increased IL12B expression, suggesting other PG-related/LPG2 dependent molecules may act to dampen the immune response. Global transcriptional profiling comparing WT, FV1 lpg1-, FV1 lpg2- infections revealed that FV1 lpg1- mutants entered hDCs in a silent fashion as indicated by repression of gene expression. Transcription factor binding site analysis suggests that LPG recognition by hDCs induces IL-12 in a signaling cascade resulting in Nuclear Factor κ B (NFκB and Interferon Regulatory Factor (IRF mediated transcription.These data suggest that L. major LPG is a major PAMP recognized by hDC to induce IL12-mediated protective immunity and that there is a complex interplay between PG-baring Leishmania surface glycoconjugates that result in modulation of host cellular IL12.

Antargaz: 1. independent French LPG marketer; Antargaz: 1. destributeur francais independant de GPL

Energy Technology Data Exchange (ETDEWEB)

Anon.

2001-04-01

Francois Varagne, recently appointed President and General Manager of Antargaz, displayed on 12 April in Paris the configuration and the ambitions of the company. A major player on the French LPG market, Antargaz makes today a new start. On the basis of its 744 000 tonnes (around 400 millions gallons) sold in 2000, Antargaz ranks as the second LPG distributor in France with a share of some 24%. Antargaz is now the first independent marketer in France, ahead of the other French independent actors: Primagaz France (around 20% of the market) and Vitogaz (some 3.5%). Thus, key factors changed in the French LPG sector. If we except marketers under 5%, there were last year one large independent (Primagaz) and three LPG marketers linked to refiners: Butagaz (as Shell affiliate + BP's French LPG output), Elf Antargaz (as Elf Aquitaine's affiliate) and Totalgaz (as TotalFina's affiliate). Today, again without counting marketers under 5%, there are two LPG marketers linked to refiners (Butagaz and Totalgaz) and two large independents. Antargaz's strategy is focused on existing markets as well as new ones and new applications: in the domestic and commercial sectors, in industry, auto-gas, mains distribution, in the leisure sector, in agriculture. It has also a role to play in Europe.

Characterization of underground storage tank sludge using fourier transform infrared photoacoustic spectroscopy

International Nuclear Information System (INIS)

Luo, S.; Bajic, S.J.; Jones, R.W.

1994-01-01

Analysis of underground storage tank (UST) contents is critical for the determination of proper disposal protocols and storage procedures of nuclear waste materials. Tank volume reduction processes during the 1940's and 50's have produced a waste form that compositionally varies widely and has a consistency that ranges from paste like sludge to saltcake. The heterogeneity and chemical reactivity of the waste form makes analysis difficult by most conventional methods which require extensive sample preparation. In this paper, a method is presented to characterize nuclear waste from UST's at the Westinghouse Hanford Site in Washington State, using Fourier transform infrared-photoacoustic spectroscopy (FTIR-PAS). FTIR-PAS measurements on milligram amounts of surrogate sludge samples have been used to accurately identify phosphate, sulfate, nitrite, nitrate and ferrocyanide components. A simple sample preparation method was followed to provide a reproducible homogeneous sample for quantitative analysis. The sample preparation method involved freeze drying the sludge sample prior to analysis to prevent the migration of soluble species. Conventional drying (e.g., air or, oven) leads to the formation of crystals near the surface where evaporation occurs. Sample preparation as well as the analytical utility of this method will be discussed

Assessment of research and development (R and D) needs in LPG safety and environmental control

Energy Technology Data Exchange (ETDEWEB)

DeSteese, J.G.

1982-05-01

The report characterizes the LPG industry covering all operations from production to end use, reviews current knowledge of LPG release phenomenology, summarizes the status of current LPG release prevention and control methodology, and identifies any remaining safety and environmental problems and recommends R and D strategies that may mitigate these problems. (ACR)

Influence of H{sub 2}O{sub 2} on LPG fuel performance evaluation

Energy Technology Data Exchange (ETDEWEB)

Khan, Muhammad Saad, E-mail: iqbalmouj@gmail.com; Ahmed, Iqbal, E-mail: iqbalmouj@gmail.com; Mutalib, Mohammad Ibrahim bin Abdul, E-mail: iqbalmouj@gmail.com; Nadeem, Saad, E-mail: iqbalmouj@gmail.com; Ali, Shahid, E-mail: iqbalmouj@gmail.com [Department of Chemical Engineering, Faculty of Engineering, Universiti Teknologi PETRONAS, Bandar Seri Iskandar, 31750 Tronoh, Perak (Malaysia)

2014-10-24

The objective of this mode of combustion is to insertion of hydrogen peroxide (H{sub 2}O{sub 2}) to the Liquefied Petroleum Gas (LPG) combustion on spark plug ignition engines. The addition of hydrogen peroxide may probably decrease the formation of NO{sub x}, CO{sub x} and unburned hydrocarbons. Hypothetically, Studies have shown that addition of hydrogen peroxide to examine the performance of LPG/H{sub 2}O{sub 2} mixture in numerous volumetric compositions starting from lean LPG until obtaining a better composition can reduce the LPG fuel consumption. The theory behind this idea is that, the addition of H{sub 2}O{sub 2} can cover the lean operation limit, increase the lean burn ability, diminution the burn duration along with controlling the exhaust emission by significantly reducing the greenhouse gaseous.

Estimating Residual Solids Volume In Underground Storage Tanks

International Nuclear Information System (INIS)

Clark, Jason L.; Worthy, S. Jason; Martin, Bruce A.; Tihey, John R.

2014-01-01

The Savannah River Site liquid waste system consists of multiple facilities to safely receive and store legacy radioactive waste, treat, and permanently dispose waste. The large underground storage tanks and associated equipment, known as the 'tank farms', include a complex interconnected transfer system which includes underground transfer pipelines and ancillary equipment to direct the flow of waste. The waste in the tanks is present in three forms: supernatant, sludge, and salt. The supernatant is a multi-component aqueous mixture, while sludge is a gel-like substance which consists of insoluble solids and entrapped supernatant. The waste from these tanks is retrieved and treated as sludge or salt. The high level (radioactive) fraction of the waste is vitrified into a glass waste form, while the low-level waste is immobilized in a cementitious grout waste form called saltstone. Once the waste is retrieved and processed, the tanks are closed via removing the bulk of the waste, chemical cleaning, heel removal, stabilizing remaining residuals with tailored grout formulations and severing/sealing external penetrations. The comprehensive liquid waste disposition system, currently managed by Savannah River Remediation, consists of 1) safe storage and retrieval of the waste as it is prepared for permanent disposition; (2) definition of the waste processing techniques utilized to separate the high-level waste fraction/low-level waste fraction; (3) disposition of LLW in saltstone; (4) disposition of the HLW in glass; and (5) closure state of the facilities, including tanks. This paper focuses on determining the effectiveness of waste removal campaigns through monitoring the volume of residual solids in the waste tanks. Volume estimates of the residual solids are performed by creating a map of the residual solids on the waste tank bottom using video and still digital images. The map is then used to calculate the volume of solids remaining in the waste tank. The ability to

Formulation and Characterization of Cu Doped ZnO Thick Films as LPG Gas Sensor

Directory of Open Access Journals (Sweden)

A. V. PATIL

2010-12-01

Full Text Available Thick films of pure and various concentrations (1 wt. %, 3 wt. %, 5 wt. %, 7 wt. % and 10 wt. % of Cu-doped ZnO were prepared on alumina substrates using a screen printing technique. These films were fired at a temperature of 700ºC for two hours in an air atmosphere. Morphological, compositional and structural properties of the samples were obtained using the scanning electron microscopy (SEM, Energy dispersive spectroscopy (EDAX and X-ray diffraction techniques respectively. The LPG gas sensing properties of these thick films were investigated at different operating temperatures and LPG gas concentrations. The surface resistance of thick films decreases when exposed to LPG gas. The Cu doped films show significant sensitivity to LPG gas than pure ZnO film. 5 wt. % Cu-doped ZnO film was found to be more sensitive (87.3 % to LPG gas exposed at 300 oC than other doping concentrations with fast response and recovery time.

Conformity checking of LPG Transportation Trucks by Modelling and Simulation

Directory of Open Access Journals (Sweden)

Gallab Maryam

2017-01-01

Full Text Available LPG Loading /unloading site is considered as a dangerous environment of significant risk, especially during LPG transfer operations. These risks may cause catastrophic dangers such as BLEVE (Boiling Liquid Expanding Vapour Explosion, UVCE (Unconfined Vapour Cloud Explosion, etc. The site consists of a tank (RST containing LPG and threetransfer posts. Two posts allow loading of small carrier tankers 6 tons. The other one transfer post transfer LPG contained injumbo tankers 20 tons inside the tank. The industrial site at risks chooses to demonstrate the need for a modelling-simulation approach. The aim is to check first compliance and authorization of the truck when it enters the site for loading /unloading, to verify the authorization to make the transfer, and then, to identify the driver and his training to ensure that the transfer operations are going to take place without incident. Sometimes, it may happen that Consignment Operator (CO is busy orabsent and thus the driver operates alone without being authorized, in this case the site risks a loss of control due to a lack of resources. The modelling-simulation will be done using multi-agent systems that will present the drivers, trucks, PO and loading unloading posts as agents in order to have a model facilitating this checking.

Kinetic modeling of liquefied petroleum gas (LPG) reduction of titania in MATLAB

Science.gov (United States)

Yin, Tan Wei; Ramakrishnan, Sivakumar; Rezan, Sheikh Abdul; Noor, Ahmad Fauzi Mohd; Izah Shoparwe, Noor; Alizadeh, Reza; Roohi, Parham

2017-04-01

In the present study, reduction of Titania (TiO2) by liquefied petroleum gas (LPG)-hydrogen-argon gas mixture was investigated by experimental and kinetic modelling in MATLAB. The reduction experiments were carried out in the temperature range of 1100-1200°C with a reduction time from 1-3 hours and 10-20 minutes of LPG flowing time. A shrinking core model (SCM) was employed for the kinetic modelling in order to determine the rate and extent of reduction. The highest experimental extent of reduction of 38% occurred at a temperature of 1200°C with 3 hours reduction time and 20 minutes of LPG flowing time. The SCM gave a predicted extent of reduction of 82.1% due to assumptions made in the model. The deviation between SCM and experimental data was attributed to porosity, thermodynamic properties and minute thermal fluctuations within the sample. In general, the reduction rates increased with increasing reduction temperature and LPG flowing time.

The tragedy of San Juanico--the most severe LPG disaster in history.

Science.gov (United States)

Arturson, G

1987-04-01

During the early morning of Monday, 19 November 1984, one of the largest disasters in industrial history occurred in the Mexico City Area, causing the greatest rescue effort to assist population in an emergency ever undertaken. The tragic catastrophe started in a large LPG (Liquid Petroleum Gas) storage and distribution centre in San Juan Ixhuatepec, 20 km north of Mexico City. The facilities, owned by the Pemex State Oil Company, consisted of six spherical storage tanks (four with a volume of 1600 m3 and two with a volume of 2400 m3) and 48 horizontal cylindrical bullet tanks of different sizes. At the time of the disaster the storage tanks contained 11,000 m3 of a mixture of propane and butane. The inhabitants of San Juan Ixhuatepec numbered about 40,000, and a further 60,000 lived in the hills surrounding the village. The majority were poor country people living in one-story houses constructed of concrete pillars filled in with bricks and with roofs of iron sheets. The disaster started due to LPG leakage, probably a pipe leakage or rupture due to excess pressure. A vapour cloud built up and was slowly moved by the north-east wind towards the ground-placed flare pit located in the western part of the plant. The vapour cloud was ignited around 5:40 a.m. and was followed by an extensive fire at the plant area. The first explosion was registered on the seismograph at the University of Mexico at 05 h 44 min 52 s and was followed by a dozen explosions within the next hour, some of them of BLEVE type (Boiling Liquid Expanding Vapour Explosion) due to rupture of one or more storage tanks. Two of the explosions had an intensity of 0.5 on the Richter scale. Unburned and burning gas entered the houses south of the plant area and set fire to everything. Blast waves from the explosions not only destroyed a number of houses but also shifted several cylindrical tanks from their supports and added more gas to the fire. The smaller spheres and some of the cylinders exploded and

Preliminary study on the combustion and emission in a direct injection LPG spark ignition engine

Energy Technology Data Exchange (ETDEWEB)

Oh, Seungmook; Lee, Seokhwan [Korea Institute of Machinery and Materials (Korea, Republic of)

2010-07-01

In the energy sector, with the implementation of stringent regulations on combustion emissions and the depletion of conventional fuels, there is an important need for low carbon fuel and advanced engine technology. Korea is the country with the most LPG vehicles in the world and the aim of this study, performed by the Korea Institute of Machinery and Materials, is to compare the performance of LPG direct injection spark ignition (DISI) with gasoline DISI. Heat release analyses were conducted to determine the combustion characteristics of both systems and experiments were performed to determine gaseous and nanoparticle emissions. Results showed that LPG provides a better thermal efficiency than gasoline and that THC, NOx, and particulate emissions were lower for LPG than for gasoline. This study demonstrated that LPG DISI can provide better combustion efficiency and lower emissions than gasoline DISI.

Modelling the pressurization induced by solar radiation on above ground installations of LPG pipeline systems

Science.gov (United States)

Leporini, M.; Terenzi, A.; Marchetti, B.; Giacchetta, G.; Polonara, F.; Corvaro, F.; Cocci Grifoni, R.

2017-11-01

Pipelining Liquefied Petroleum Gas (LPG) is a mode of LPG transportation more environmentally-friendly than others due to the lower energy consumption and exhaust emissions. Worldwide, there are over 20000 kilometers of LPG pipelines. There are a number of codes that industry follows for the design, fabrication, construction and operation of liquid LPG pipelines. However, no standards exist to modelling particular critical phenomena which can occur on these lines due to external environmental conditions like the solar radiation pressurization. In fact, the solar radiation can expose above ground pipeline sections at pressure values above the maximum Design Pressure with resulting risks and problems. The present work presents an innovative practice suitable for the Oil & Gas industry to modelling the pressurization induced by the solar radiation on above ground LPG pipeline sections with the application to a real case.

Ecology and economic estimate of using of the underground excavation space

International Nuclear Information System (INIS)

Umnov, V.A.; Tarasov, V.F.; Tret'yakov, I.O.; Sheloumov, A.A.

1995-01-01

Stages of ecological and economic estimates of utilizing underground space, including evaluation of underground space resources, selection of its utilization trends and substantiation of optimal parameters for selected trends, are considered. Certain directions of possible repeated utilization of mining excavations are shown, including underground hydropower stations, underground energy storages, underground nuclear stations. Underground waste disposal is one of the most available directions in utilization of the underground space presently. Evaluation of the underground space utilization at all stages envisages complete account of all economical, social and ecological results

Experimental study of dual fuel engine performance using variable LPG composition and engine parameters

International Nuclear Information System (INIS)

Elnajjar, Emad; Selim, Mohamed Y.E.; Hamdan, Mohammad O.

2013-01-01

Highlights: • The effect of using variable LPG is studied. • Five fuels with propane to butane % volume ratio are: 100-70-55-25-0. • 100% Propane composition shows the highest noise levels with similar performance. • At 45° BTDC injection timing 55% Propane LPG the only fuel experience knocking. • LPG fuels gave similar engine performance, with differences in levels of noise. - Abstract: The present work investigates experimentally the effect of LPG fuel with different composition and engine parameters on the performance of a dual compression engine. Five different blends of LPG fuels are used with Propane to Butane volume ratio of 100:0, 70:30, 55:45, 25:75, and 0:100. A single cylinder, naturally aspirated, four strokes, indirectly injected, water cooled modified Ricardo E6 engine, is used in this study. The study is carried out by measuring the cylinder pressure, engine load, engine speed, crank angle, and the fuel’s flow rate. The engine performance under variable LPG fuel composition, engine load, pilot fuel injection timing, compression ratio, pilot fuel mass and engine speed, are estimated by comparing the following engine parameters: the cylinder maximum pressure, the indicated mean effective pressure, the maximum rate of pressure rise, and the thermal efficiency. The experimental data indicates that the engine parameters are playing a major role on the engine’s performance. Different LPG fuel composition did not show a major effect on the engine efficiency but directly impacted the levels of generated combustion noise

A forum on LPG vehicles and leasing; Un forum sur les vehicules GPL et la LLD

Energy Technology Data Exchange (ETDEWEB)

Fridman, G.

1999-04-01

As a specialist of vehicle leasing, Axus France cooperated with Arthur Andersen, Butagaz and Volvo to promote the LPG solution to managers. Axus France offers with LPG vehicles leasing a range of tailor made products and services. Thus, the company estimates that LPG economics applied through vehicle leasing are not sufficiently large from Diesel (its calculation gives only 2 %) on some utilizations. This is why Axus offers an extra incitement to its customers, by keeping the financial risk linked to the LPG vehicle resale. (authors)

78 FR 57625 - Arlington Storage Company, LLC; Notice of Availability of the Environmental Assessment for the...

Science.gov (United States)

2013-09-19

... existing salt caverns previously used for liquefied petroleum gas (LPG) storage, the proposed Gallery 2... caverns, known as Gallery 2, to natural gas storage at its Seneca Lake Storage facility in Schuyler County, New York. The conversion of the Gallery 2 caverns to natural gas storage would add 0.55 billion cubic...

Study of the cycle variability at an automotive diesel engine fuelled with LPG

Directory of Open Access Journals (Sweden)

Nemoianu Liviu

2017-01-01

Full Text Available Liquid Petroleum Gas is a viable alternative fuel for diesel engines due to its ability of emissions and fuel consumption reduction. Combustion variability at LPG diesel engine is analysed for maximum pressure, maximum pressure angle and indicated mean effective pressure. Combustion variability is influenced by the increase of LPG cycle dose which lead to the increase of the cycle variability coefficients values, but without exceeding the admitted values that provide diesel engine reliability. Analysis of COV values establishes the maximum admitted values of LPG cycle.

Aboveground storage tanks

International Nuclear Information System (INIS)

Rizzo, J.A.

1992-01-01

With the 1988 promulgation of the comprehensive Resource Conservation and Recovery Act (RCRA) regulations for underground storage of petroleum and hazardous substances, many existing underground storage tank (UST) owners have been considering making the move to aboveground storage. While on the surface, this may appear to be the cure-all to avoiding the underground leakage dilemma, there are many other new and different issues to consider with aboveground storage. The greatest misconception is that by storing materials above ground, there is no risk of subsurface environmental problems. it should be noted that with the aboveground storage tank (AGST) systems, there is still considerable risk of environmental contamination, either by the failure of onground tank bottoms or the spillage of product onto the ground surface where it subsequently finds its way to the ground water. In addition, there are added safety concerns that must be addressed. So what are the other specific areas of concern besides environmental to be addressed when making the decision between underground and aboveground tanks? The primary issues that will be addressed in this paper are: Safety, Product Losses, Cost Comparison of USTs vs AGSTs, Space Availability/Accessibility, Precipitation Handling, Aesthetics and Security, Pending and Existing Regulations

Underground storage touted as CO2 solution

International Nuclear Information System (INIS)

Kishewitsch, S.

2000-01-01

As power generating companies weigh the merits of switching from coal to natural gas in order to reduce carbon dioxide emissions into the atmosphere, energy analysts predict that coal will remain a major contributor to world energy supplies well into the 21st century. For example, the Electric Power Institute estimates that a new 1,000 MW power plant need to be built somewhere in the world every two days for the next fifty years to meet the global demand for energy, and that in major emerging economies such as India and China, many of those plants will be fueled by coal. Various methods already are being tried to safely contain the carbon dioxide resulting from this vastly carbon-intensive economy. One of the more promising approaches involves burying the gas deep in the ground where it will stay safely for hundreds, if not thousands of years. Burial underground may take the form of burial in deep exhausted oil or gas formations, or burial in the deep ocean. Injection into exhausted oil and gas formations is favoured because of the ready availability of thousands of gigatonnes of underground formations and because of the extensive knowledge base already in existence regarding the size and geological properties of oil and gas reservoirs and the behaviour of carbon dioxide under these conditions. Injecting carbon dioxide into unmineable coal seams could replace methane bound to the coal; it is already being done in Alberta as one of the two pilot projects in North America, the other being in Mexico. Carbon dioxide injection to stimulate enhanced oil recovery is also being experimented with, among others by PanCanadian Resources Ltd at its Weyburn reservoir in Saskatchewan. Injection into salt domes and deep saline aquifers is another alternative. Sequestration in the ocean in a variety of forms is also the subject of several experiments. To illustrate the attractiveness of deep ocean storage, it is stated that the ocean contains at least 50 times more carbon than the

Underground gas storage Uelsen: Findings from planning, building and commissioning the surface buildings and structures; Untertagegasspeicher (UGS) Uelsen: Erkenntnisse aus Planung, Bau und Inbetriebnahme der obertaegigen Anlagen

Energy Technology Data Exchange (ETDEWEB)

Focke, H.; Brueggmann, R.; Mende, F.; Steinkraus, D.; Wauer, R. [BEB Erdgas und Erdoel GmbH, Hannover (Germany)

1998-12-31

The article describes the concepts of the plants and equipment and the specific features of the underground storage at Uelsen. The underground storage will be purpose-built as an H-gas storage in a nearly depleted sandstone deposit. At a nominal deliverability of 250.000 cubic m/h (Vn) the storage at Uelsen has more potential for expansion. This potential was taken into account by designing appropriate pressure stages, capacities, performance characteristics and space. (orig.). [Deutsch] Die nachfolgende Veroeffentlichung stellt das anlagentechnische Grundkonzept und die spezifischen Besonderheiten des UGS Uelsen dar. Der im suedwestlichen Niedersachsen als H-Gasspeicher in einer nahezu ausgefoerderten Buntsandsteinlagerstaette eingerichtete UGS Uelsen wird in mehreren Ausbaustufen bedarfsgerecht fertiggestellt. Bei einer Nennentnahmekapazitaet von 450.000 m{sup 3}/h (Vn) und einer Nenninjektionsleistung von 250.000 m{sup 3}/h (Vn) weist der UGS Uelsen noch weiteres Potential fuer Erweiterungen auf. Dieses Ausbaupotential wurde bei der Planung und dem Bau der bestehenden Anlagen durch Festlegung entsprechender Druckstufen, Kapazitaeten, Leistungsgroessen und Platzanordnungen beruecksichtigt. (orig.)

A review of technology for verification of waste removal from Hanford Underground Storage Tanks (WHC Issue 30)

International Nuclear Information System (INIS)

Thunborg, S.

1994-09-01

Remediation of waste from Underground Storage Tanks (UST) at the Hanford Waste storage sites will require removal of all waste to a nearly clean condition. Current requirements are 99% clean. In order to meet remediation legal requirements, a means to remotely verify that the waste has been removed to sufficient level is needed. This report discusses the requirements for verification and reviews major technologies available for inclusion in a verification system. The report presents two operational scenarios for verification of residual waste volume. Thickness verification technologies reviewed are Ultrasonic Sensors, Capacitance Type Sensors, Inductive Sensors, Ground Penetrating Radar, and Magnetometers. Of these technologies Inductive (Metal Detectors) and Ground Penetrating Radar appear to be the most suitable for use as waste thickness sensors

Tools for Inspecting and Sampling Waste in Underground Radioactive Storage Tanks with Small Access Riser Openings

International Nuclear Information System (INIS)

Nance, T.A.

1998-01-01

Underground storage tanks with 2 inches to 3 inches diameter access ports at the Department of Energy's Savannah River Site have been used to store radioactive solvents and sludge. In order to close these tanks, the contents of the tanks need to first be quantified in terms of volume and chemical and radioactive characteristics. To provide information on the volume of waste contained within the tanks, a small remote inspection system was needed. This inspection system was designed to provide lighting and provide pan and tilt capabilities in an inexpensive package with zoom abilities and color video. This system also needed to be utilized inside of a plastic tent built over the access port to contain any contamination exiting from the port. This system had to be build to travel into the small port opening, through the riser pipe, into the tank evacuated space, and out of the riser pipe and access port with no possibility of being caught and blocking the access riser. Long thin plates were found in many access riser pipes that blocked the inspection system from penetrating into the tank interiors. Retrieval tools to clear the plates from the tanks using developed sampling devices while providing safe containment for the samples. This paper will discuss the inspection systems, tools for clearing access pipes, and solvent sampling tools developed to evaluate the tank contents of the underground solvent storage tanks

Optimal use of the Gaz de France underground gas storage facilities; Utilisation optimale des stockages souterrains de Gaz de France

Energy Technology Data Exchange (ETDEWEB)

Favret, F.; Rouyer, E.; Bayen, D.; Corgier, B. [Gaz de France (GDF), 75 - Paris (France)

2000-07-01

This paper describes the tools developed by Gaz de France to optimize the use of its whole set of underground gas storage facilities. After a short introduction about the context and the purposes, the methodology and the models are detailed. The operational results obtained during the last three years are presented, and some conclusions and perspectives are given. (authors)

Underground storage of heat

International Nuclear Information System (INIS)

Despois, J.; Nougarede, F.

1976-01-01

The interest laying in heat storage is envisaged taking account of the new energy context, with a view to optimizing the use of production means of heat sources hardly modulated according to the demand. In such a way, a natural medium, without any constructions cost but only an access cost is to be used. So, porous and permeable rocky strata allowing the use of a pressurized water flow as a transfer fluid are well convenient. With such a choice high temperatures (200 deg C) may be obtained, that are suitable for long transmissions. A mathematical model intended for solving the conservation equations in the case of heat storage inside a confined water layer is discussed. An approach of the operating conditions of storage may involve either a line-up arrangement (with the hot drilling at the center, the cold drillings being aligned on both sides) or a radial arrangement (with cold drillings at the peripheral edge encircling the hot drilling at the center of the layer). The three principal problems encountered are: starting drilling, and the circuit insulation and control [fr

Early Leakage Protection System of LPG (Liquefied Petroleum Gas) Based on ATMega 16 Microcontroller

Science.gov (United States)

Sriwati; Ikhsan Ilahi, Nur; Musrawati; Baco, Syarifuddin; Suyuti'Andani Achmad, Ansar; Umrianah, Ejah

2018-04-01

LPG (Liquefied Petroleum Gas). LPG is a hydrocarbon gas production from refineries and gas refinery with the major components of propane gas (C3H8) and butane (C4H10). Limit flame (Flammable Range) or also called gas with air. Value Lower Explosive Limit (LEL) is the minimum limit of the concentration of fuel vapor in the air which if there is no source of fire, the gas will be burned. While the value of the Upper Explosive Limit (UEL), which limits the maximum concentration of fuel vapor in the air, which if no source of fire, the gas will be burned. Protection system is a defend mechanism of human, equipment, and buildings around the protected area. Goals to be achieved in this research are to design a protection system against the consequences caused by the leakage of LPG gas based on ATmega16 microcontroller. The method used in this research is to reduce the levels of leaked LPG and turned off the power source when the leakage of LPG is on the verge of explosive limit. The design of this protection system works accurately between 200 ppm up to 10000 ppm, which is still below the threshold of explosive. Thus protecting the early result of that will result in the leakage of LPG gas.

Assessment of concentration mechanisms for organic wastes in underground storage tanks at Hanford

International Nuclear Information System (INIS)

Gerber, M.A.; Burger, L.L.; Nelson, D.A.; Ryan, J.L.; Zollars, R.L.

1992-09-01

Pacific Northwest Laboratory (PNL) has conducted an initial conservative evaluation of physical and chemical processes that could lead to significant localized concentrations of organic waste constituents in the Hanford underground storage tanks (USTs). This evaluation was part of ongoing studies at Hanford to assess potential safety risks associated with USTs containing organics. Organics in the tanks could pose a potential problem if localized concentrations are high enough to propagate combustion and are in sufficient quantity to produce a large heat and/or gas release if in contact with a suitable oxidant. The major sources of oxidants are oxygen in the overhead gas space of the tanks and sodium nitrate and nitrite either as salt cake solids or dissolved in the supernatant and interstitial liquids

Underground gas storage Lobodice geological model development based on 3D seismic interpretation

International Nuclear Information System (INIS)

Kopal, L.

2015-01-01

Aquifer type underground gas storage (UGS) Lobodice was developed in the Central Moravian part of Carpathian foredeep in Czech Republic 50 years ago. In order to improve knowledge about UGS geological structure 3D seismic survey was performed in 2009. Reservoir is rather shallow (400 - 500 m below surface) it is located in complicated locality so limitations for field acquisition phase were abundant. This article describes process work flow from 3D seismic field data acquisition to geological model creation. The outcomes of this work flow define geometry of UGS reservoir, its tectonics, structure spill point, cap rock and sealing features of the structure. Improving of geological knowledge about the reservoir enables less risky new well localization for UGS withdrawal rate increasing. (authors)

Corrective action baseline report for underground storage tank 2331-U Building 9201-1

International Nuclear Information System (INIS)

1994-01-01

The purpose of this report is to provide baseline geochemical and hydrogeologic data relative to corrective action for underground storage tank (UST) 2331-U at the Building 9201-1 Site. Progress in support of the Building 9201-1 Site has included monitoring well installation and baseline groundwater sampling and analysis. This document represents the baseline report for corrective action at the Building 9201-1 site and is organized into three sections. Section 1 presents introductory information relative to the site, including the regulatory initiative, site description, and progress to date. Section 2 includes the summary of additional monitoring well installation activities and the results of baseline groundwater sampling. Section 3 presents the baseline hydrogeology and planned zone of influence for groundwater remediation

Assessment of concentration mechanisms for organic wastes in underground storage tanks at Hanford

Energy Technology Data Exchange (ETDEWEB)

Gerber, M.A.; Burger, L.L.; Nelson, D.A.; Ryan, J.L. (Pacific Northwest Lab., Richland, WA (United States)); Zollars, R.L. (Washington State Univ., Pullman, WA (United States))

1992-09-01

Pacific Northwest Laboratory (PNL) has conducted an initial conservative evaluation of physical and chemical processes that could lead to significant localized concentrations of organic waste constituents in the Hanford underground storage tanks (USTs). This evaluation was part of ongoing studies at Hanford to assess potential safety risks associated with USTs containing organics. Organics in the tanks could pose a potential problem if localized concentrations are high enough to propagate combustion and are in sufficient quantity to produce a large heat and/or gas release if in contact with a suitable oxidant. The major sources of oxidants are oxygen in the overhead gas space of the tanks and sodium nitrate and nitrite either as salt cake solids or dissolved in the supernatant and interstitial liquids.

Conceptual Model of Supply Chain Structure Mapping - A Case of Subsidized LPG Commodity in Yogyakarta

Science.gov (United States)

Sulistio, Joko; Thoif, Afifuddin; Fitri Alindira, Aulia

2016-01-01

— In 2007, the government launched a conversion program of kerosene to LPG by issuing a Presidential Regulation No. 104/2007 on Supply, Distribution and Pricing LPG 3 Kg. Article 2 on the regulation says that setting the supply, distribution, and pricing of LPG 3 Kg include planning an annual sales volume of enterprises, the reference price and the retail price and conditions of export and import of LPG 3 Kg in order to reduce subsidies Kerosene especially to divert the use of kerosene according to government policy. In principle, the purpose of this policy is to reduce energy subsidies on commodities, especially Kerosene. Although the government claimed the conversion program is success, there are few problems arising from conversion program. In 2014, many scarcity and high price of LPG 3 Kg were reported. In this case, Pertamina was given full authority to manage all supply chain and distribution. Because the root of the problem of scarcity that occurred in the supply chain system has not been explained, the proposed solutions will also be partial and not comprehensive. Thus, this research will build a structural map of the causes of supply chain system LPG 3 Kg, as well as providing a comprehensive picture of system dynamics of LPG 3 Kg supply chain system which applied in Indonesia. And the result is expected as in form of Causal Loop Diagram of supply chain system.

PENGUJIAN MESIN DIESEL YANG DIMODIFIKASI MENJADI BERBAHAN BAKAN GAS LPG

OpenAIRE

Himsar Ambarita

2017-01-01

Pada penelitian ini dilakukan modifikasi pada sebuah mesin diesel yang awalnya digerakkan dengan menggunakan bahan bakar diesel menjadi berbahan bakar LPG. Telah dirancang suatu alat uji yang menggunakan sebuah mesin diesel silinder tunggal dengan daya 2,5 kW dan 2,8 kW pada putaran mesin 3000 dan 3600 rpm. Kinerja mesin diesel kecil telah diuji dalam dua bahan bakar berbeda yaitu solar dan LPG. Pada penggunaan bahan bakar solar tidak ada perubahan yang dilakukan pada mesin disel. Pada penggu...

Non-uniform regulations of underground storage tanks in the United States

International Nuclear Information System (INIS)

Nadim, F.; Hoag, G.E.; Liu, S.; Carley, R.J.; Zack, P.

2000-01-01

Leaking underground storage tanks (USTs) are one of the major sources of ground water contamination. United States federal regulations for USTs were established in September of 1988. Since that time little or no amendments have been made to these regulations. In order to protect sensitive areas such as aquifer recharge zones for public water supply wells and wetlands, different states have been obligated to apply more stringent standards than the federal UST regulations. This practice however, has led to a non-uniform application of regulations for USTs throughout the country. In this article, United States regulations for USTs are reviewed and its deficits are highlighted. Based on these regulations and the experience of northeastern states of United States, a sequence of leak and spill preventive measures for USTs is proposed. Application of the proposed measures could substantially reduce the possibility of UST failure and would be more protective of the subsurface environment. (author)

33 CFR 165.103 - Safety and Security Zones; LPG Vessel Transits in Portland, Maine, Captain of the Port Zone...

Science.gov (United States)

2010-07-01

... within a 500-yard radius of any Liquefied Petroleum Gas (LPG) vessel while it is moored at the LPG... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety and Security Zones; LPG... and Security Zones; LPG Vessel Transits in Portland, Maine, Captain of the Port Zone, Portsmouth...

Kecepatan Pembakaran Premixed Campuran Minyak Jarak - Liquefied Petroleum Gas (LPG pada Circular Tube Burner

Directory of Open Access Journals (Sweden)

Defmit B.N. Riwu

2016-10-01

Full Text Available This study was conducted to determine the characteristics of premixed combustion of a mixture of castor oil - LPG on a circular tube burner. Percentage of LPG fuel in a mixture of jatropha curcas oil - LPG varied as much as 10%, 20%, 30%, and 40% of the mass flow jatropha curcas oil vapor. Considering the flame of fire there are two angles formed which describe burning velocity. Also there are formed two cones of fire where the bright blue inside cone is a premixed flame, while the outer blue white cone is flame a diffusion flame. An increase in the percentage of LPG makes the value of top and bottom angle increase. So that the burning velocity on the upper angle decrease whilst on bottom angle increase.

Report of study group 3.3 ''LNG and LPG peak shaving and satellite plants''; Rapport du groupe d'etude 3.3 ''usines d'ecretement de pointes et stations satellites GNL et GPL''

Energy Technology Data Exchange (ETDEWEB)

Klein Nagelvoort, R.

2000-07-01

This report presents a world-wide overview of LNG and LPG Peak Shaving and Satellite Plants, compiled by the study group 3.3 of the International Gas Union. The scope of the work of the study group includes: - LPG peak shavers (LPG + air, N{sub 2}) in gas distribution networks; - LPG peak shavers for start-up and back-up fuel for LNG terminals and power stations; - LNG peak shavers for gas distribution networks; - Small-scale liquefaction plants for distribution to satellites and dedicated consumers (e.g. power generators, chemical plants, trucking companies etc.); - LNG peak shavers as back-up for large consumers; - Alternative liquefaction technologies for LNG and LPG (e.g. refrigeration cycles, supersonic expansion, thermo-acoustic designs); - Alternative storage tank designs for LNG and LPG. The report presents an overview of current installations world-wide and considers the prospects of technological developments with respect to equipment, remote operations and safety constraints. It also includes where possible a review of capital and operating costs, regulations, and an identification of opportunities and trends. The report collates the information available to the study group at the time of the writing, which may explain some heterogeneity in the document. (author)

Effectiveness of replacing catalytic converters in LPG-fueled vehicles in Hong Kong

Directory of Open Access Journals (Sweden)

X. Lyu

2016-05-01

Full Text Available Many taxis and public buses are powered by liquefied petroleum gas (LPG in Hong Kong. With more vehicles using LPG, they have become the major contributor to ambient volatile organic compounds (VOCs in Hong Kong. An intervention program which aimed to reduce the emissions of VOCs and nitrogen oxides (NOx from LPG-fueled vehicles was implemented by the Hong Kong government in September 2013. Long-term real-time measurements indicated that the program was remarkably effective in reducing LPG-related VOCs, NOx and nitric oxide (NO in the atmosphere. Receptor modeling results further revealed that propane, propene, i-butane, n-butane and NO in LPG-fueled vehicle exhaust emissions decreased by 40.8 ± 0.1, 45.7 ± 0.2, 35.7 ± 0.1, 47.8 ± 0.1 and 88.6 ± 0.7 %, respectively, during the implementation of the program. In contrast, despite the reduction of VOCs and NOx, O3 following the program increased by 0.40 ± 0.03 ppbv (∼  5.6 %. The LPG-fueled vehicle exhaust was generally destructive to OH and HO2. However, the destruction effect weakened for OH and it even turned to positive contribution to HO2 during the program. These changes led to the increases of OH, HO2 and HO2 ∕ OH ratio, which might explain the positive O3 increment. Analysis of O3–VOCs–NOx sensitivity in ambient air indicated VOC-limited regimes in the O3 formation before and during the program. Moreover, a maximum reduction percentage of NOx (i.e., 69 % and the lowest reduction ratio of VOCs ∕ NOx (i.e., 1.1 in LPG-fueled vehicle exhaust were determined to give a zero O3 increment. The findings are of great help to future formulation and implementation of control strategies on vehicle emissions in Hong Kong, and could be extended to other regions in China and around the world.

Geo-science aims of underground exploration of the Gorleben salt mine

International Nuclear Information System (INIS)

Langer, M.; Venzlaff, H.

1987-01-01

The measures taken are explained separately, according to the technical areas geology/petrography - geophysics - engineering geology/geotechnology - geo-chemistry. The results of the underground exploration are used directly to produce documents for the planning process, securing proof and the final storage planning (specific site mine dimensions, analysis of accidents, storage strategies). After completion of underground exploration, geoscience information on the suitability of the salt mine at Gorleben will be available in connection with a storage concept agreed between the geo-technologists and the mining engineers. (orig.) [de

Pengaruh Perubahan Saat Penyalaan (Ignition Timing) Terhadap Prestasi Mesin Pada Sepeda Motor 4 Langkah Dengan Bahan Bakar Lpg

OpenAIRE

Yunianto, Bambang

2010-01-01

Bahan bakar LPG merupakan bahan bakar gas yang ramah lingkungan, sehingga dapat dijadikan bahan bakar alternatif selain bahan bakar bensin Performa Mesin bensin yang dioperasikan dengan menggunakan bahan bakar gas LPG mengalami penurunan. Penurunan ini terjadi dikarenakan karakteristik sifat bahan bakar bensin berbeda dengan LPG. Hal ini dapat diatasi dengan mengatur saat penyalaan sehingga lebih sesuai dengan karakteristik gas LPG. Dari hasil pengujian diperoleh bahwa dengan pengaturan saat ...

NKT cell activation by Leishmania mexicana LPG: Description of a novel pathway.

Science.gov (United States)

Zamora-Chimal, Jaime; Fernández-Figueroa, Edith A; Ruiz-Remigio, Adriana; Wilkins-Rodríguez, Arturo A; Delgado-Domínguez, José; Salaiza-Suazo, Norma; Gutiérrez-Kobeh, Laila; Becker, Ingeborg

2017-02-01

NKT cells have been associated with protection against Leishmania donovani, yet their role in infections with Leishmania mexicana has not been addressed, nor has the activation pathway been defined after stimulation with Leishmania mexicana lipophosphoglycan (LPG). We analyzed the activation of NKT cells and their cytokine production in response to Leishmania mexicana LPG. Additionally we compared NKT-cell numbers and cytokine profile in lymph nodes of skin lesions induced by Leishmania mexicana in BALB/c and C57BL/6 mice. We show that LPG activates NKT cells primarily through the indirect pathway, initiating with TLR2 stimulation of dendritic cells (DC), thereby enhancing TLR2, MHC II, and CD86 expressions and IL-12p70 production. This leads to IFN-γ production by NKT cells. C57BL/6 mice showed enhanced DC activation, which correlated with augmented IFN-γ production by NKT cells. Additionally, infected C57BL/6 mice showed elevated percentages of NKT cells with higher IFN-γ and IL-4 production in lymph nodes. We conclude that the response of NKT cells towards Leishmania mexicana LPG initiates with the indirect activation, after binding of LPG to TLR2 in DC. This indirect activation pathway enables NKT cells to produce IFN-γ during the innate phase of Leishmania infection, the magnitude of which differs between mouse strains. Copyright © 2016 The Authors. Published by Elsevier GmbH.. All rights reserved.

Panorama 2014 - The importance of underground storage in the security of European gas supplies

International Nuclear Information System (INIS)

Cornot-Gandolphe, Sylvie

2013-12-01

While European capacity for underground gas storage has increased by 16% over the last three years, levels of stock at the beginning of the 2013/2014 winter, in relation to capacity, are the lowest that have been seen since 2010; they represent only 84% of storage capacity. The suppliers of gas have no incentive to reserve storage capacity, for which the cost is considered too high in relation to the spread, currently very low, between the price of gas in winter and in summer. They also rely on sufficient gas supply thanks to other sources of flexibility available on the market: flexibility of production or imports, spot LNG purchases, purchases in the spot market... or even use of the storage capacities of neighbouring countries via European network interconnections. Yet, the 2013/2014 winter is beginning in a gas supply context in Europe that is more difficult: imports of LNG, which had already dropped sharply in 2012, have continued to contract, faced with increased competition from Asian buyers on the international LNG market. Gas imports from Norway are also declining following production limits in that country. Only Russia has strongly increased its exports to Europe in 2013. However, the dispute between Ukraine and Russia about the price of Russian gas delivered to Ukraine still raises the spectre of a threat to the European supply of Russian gas, nearly 60% of which transits via Ukraine. Under these circumstances, as demonstrated by the gas crises of 2006 and 2009 and the cold conditions of February 2012 and March/April 2013, storage is the most efficient means of securing the supply of gas providing, of course, that the storage sites are filled at the beginning of winter. (author)

Storage of oil above ground for underground: Regulations, costs, and risks

International Nuclear Information System (INIS)

Lively-Diebold, B.; Driscoll, W.; Ameer, P.; Watson, S.

1993-01-01

Some owners of underground storage tank systems (USTs) appear to be replacing their systems with aboveground storage tank systems (ASTs) without full knowledge of the US Government environmental regulations that apply to facilities with ASTs, and their associated costs. This paper discusses the major federal regulatory requirements for USTs and ASTS, and presents the compliance costs for new tank systems that range in capacity from 1,000 to 10,000 gallons. The costs of two model UST system and two model AST systems are considered for new oil storage capacity, expansion of existing capacity, and replacement of an existing UST or AS T. For new capacity, ASTs are less expensive than USTs, although ASTs do have significant regulatory compliance costs that range from an estimated $8,000 to $14,000 in present value terms, depending on the size and type of system. For expanded or replacement capacity, ASTs are in all but one case less expensive than USTS; the exception is the expansion of capacity at an existing UST facility. In this case, the cost of a protected steel tank UST system is comparable to the cost of an AST system. Considering the present value of all costs over a 30 year useful life, the cost for an AST with a concrete dike is less than the cost of an AST with an earthen dike, for the tank sizes considered. This is because concrete dikes are cost competitive for small tanks, and the costs to clean up a release are higher for earthen dikes, due to the cost of disposal and replacement of oil-contaminated soil. The cost analyses presented here are not comprehensive, and are intended primarily for illustrative purposes. Only the major costs of tank purchase, installation, and regulatory compliance were considered

PENGARUH PERUBAHAN SAAT PENYALAAN (IGNITION TIMING TERHADAP PRESTASI MESIN PADA SEPEDA MOTOR 4 LANGKAH DENGAN BAHAN BAKAR LPG

Directory of Open Access Journals (Sweden)

Bambang Yunianto

2012-07-01

Full Text Available Bahan bakar LPG merupakan bahan bakar gas yang ramah lingkungan, sehingga dapat dijadikan bahan bakar alternatif selain bahan bakar bensin Performa Mesin bensin yang dioperasikan dengan menggunakan bahan bakar gas LPG mengalami penurunan. Penurunan ini terjadi dikarenakan karakteristik sifat bahan bakar bensin berbeda dengan LPG. Hal ini dapat diatasi dengan mengatur saat penyalaan sehingga lebih sesuai dengan karakteristik gas LPG. Dari hasil pengujian diperoleh bahwa dengan pengaturan saat penyalaan 11° sebelum TMA, menghasilkan prestasi (Torsi dan Daya yang dekat dengan prestasi motor bensin yaitu hanya selisih 3 %. Prestasi terbaik pada mesin bahan bakar bensin ataupun LPG berkisar pada putaran 4000 s.d 5000 rpm

Technical evaluation and assessment of CNG/LPG bi-fuel and flex-fuel vehicle viability

Science.gov (United States)

Sinor, J. E.

1994-05-01

This report compares vehicles using compressed natural gas (CNG), liquefied petroleum gas (LPG), and combinations of the two in bi-fuel or flex-fuel configurations. Evidence shows that environmental and energy advantages can be gained by replacing two-fuel CNG/gasoline vehicles with two-fuel or flex-fuel systems to be economically competitive, it is necessary to develop a universal CNG/LPG pressure-regulator-injector and engine control module to switch from one tank to the other. For flex-fuel CNG/LPG designs, appropriate composition sensors, refueling pumps, fuel tanks, and vaporizers are necessary.

Closure Report for Underground Storage Tank 2310-U at the Pine Ridge West Repeater Station

International Nuclear Information System (INIS)

1994-07-01

This document represents the Closure Report for Underground Storage Tank (UST) 2310-U at the Pine Ridge West Repeater Station, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee. Tank 2310-U was a 200-gal gasoline UST which serviced the emergency generator at the Repeater Station. The tank was situated in a shallow tank bay adjacent to the Repeater Station along the crest of Pine Ridge. The tank failed a tightness test in October 1989 and was removed in November 1989. The purpose of this report is to document completion of soil corrective action, present supporting analytical data, and request closure for this site

Fiscal 2000 report on result of R and D of underground storage technology for carbon dioxide; 2000 nendo nisanka tanso chichu choryu gijutsu kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

This paper presents the fiscal 2000 results of R and D of underground storage technology for carbon dioxide. As basic experiments, a measurement apparatus was manufactured for simulating the pressure and temperature conditions in aquifers to measure the rate at which CO{sub 2} is dissolved in water and the reactivity between CO{sub 2} and rocks, with the basic performance verified. Methods were investigated and classified that monitor environmental impact and safety. For the purpose of anticipating the long-term behaviors of CO{sub 2} sequestered underground, a simulator was developed, extracting, from investigation of the literature, natural phenomena required for the anticipation. As the system studies, examination was conducted for analysis of the energy balance of the underground storage technology, rational design (safety and economy) of an entire system ranging from source to storage point, investigation from social and economic perspectives, and estimation of the effect of suppressing global warming. In the injection experiment, Minami-Nagaoka natural gas field was selected as a prospective experiment site from the characteristics of the cap rock and aquifer. One injection well was drilled to a depth of 1,230 m, with investigations performed such as physical well-logging and core sampling. Existing data were utilized in the simulation study of CO{sub 2} behavior underground during the injection period. The information of the basic geophysical survey/exploratory well by the Japan National Oil Corporation was collected and compiled, with the preliminary geological study undertaken in the areas described. (NEDO)

LPG in large pipelines; Operacao com GLP em oleodutos de grande extensao

Energy Technology Data Exchange (ETDEWEB)

Santos, Celio Pereira dos; Agostineti, Antonio [PETROBRAS Transporte S.A. (TRANSPETRO), Rio de Janeiro, RJ (Brazil)

2003-07-01

OSBRA Pipeline is the largest pipeline of the Brazil. It has its beginning in the Refinery REPLAN, in Sao Paulo and it is going to Brasilia, in the Distrito Federal traveling 980 kilometers through three states and Distrito Federal. Flow rate inferior to one of the project, alterations in the specification of the quality for sale and operational deficiencies contributed to the difficulty of maintenance of the quality of LPG with relationship to the oleaginous residue. A Batch Test was idealized to trace of the possible points of contamination along the pipeline under controlled conditions. Pig separator was used in the interface among the gasoline and LPG, and adopted new procedure, for the operator of the control center, to avoid the start of the pumps that were with its internal lines filled with other product. The results showed viability of the operation with LPG in the OSBRA pipeline, even without need of alterations in the current physical facilities. Some improvements in facilities, as well as, new technologies of pig separator can improve the maintenance of the quality of LPG reducing possibilities of contamination, and also reducing the volume of the interface. (author)

Current status of ground source heat pumps and underground thermal energy storage in Europe

Energy Technology Data Exchange (ETDEWEB)

Sanner, B. [Justus Liebig University, Giessen (Germany). Institute of Applied Geosciences; Karytsas, C.; Mendrinos, D. [Center for Renewable Energy Sources, Pikermi (Greece); Rybach, L. [Geowatt AG, Zurich (Switzerland)

2003-12-01

Geothermal Heat Pumps, or Ground Coupled Heat Pumps (GCHP), are systems combining a heat pump with a ground heat exchanger (closed loop systems), or fed by ground water from a well (open loop systems). They use the earth as a heat source when operating in heating mode, with a fluid (usually water or a water-antifreeze mixture) as the medium that transfers the heat from the earth to the evaporator of the heat pump, thus utilising geothermal energy. In cooling mode, they use the earth as a heat sink. With Borehole Heat Exchangers (BHE), geothermal heat pumps can offer both heating and cooling at virtually any location, with great flexibility to meet any demands. More than 20 years of R and D focusing on BUE in Europe has resulted in a well-established concept of sustainability for this technology, as well as sound design and installation criteria. Recent developments are the Thermal Response Test, which allows in-situ-determination of ground thermal properties for design purposes, and thermally enhanced grouting materials to reduce borehole thermal resistance. For cooling purposes, but also for the storage of solar or waste heat, the concept of underground thermal energy storage (UTES) could prove successful. Systems can be either open (aquifer storage) or can use BHE (borehole storage). Whereas cold storage is already established on the market, heat storage, and, in particular, high temperature heat storage (> 50{sup o}C) is still in the demonstration phase. Despite the fact that geothermal heat pumps have been in use for over 50 years now (the first were in the USA), market penetration of this technology is still in its infancy, with fossil fuels dominating the space heating market and air-to-air heat pumps that of space cooling. In Germany, Switzerland, Austria, Sweden, Denmark, Norway, France and the USA, large numbers of geothermal heat pumps are already operational, and installation guidelines, quality control and contractor certification are now major issues

Revised corrective action plan for underground storage tank 2331-U at the Building 9201-1 Site

International Nuclear Information System (INIS)

Bohrman, D.E.; Ingram, E.M.

1993-09-01

This document represents the Corrective Action Plan for underground storage tank (UST) 2331-U, previously located at Building 9201-1, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee. Tank 2331-U, a 560-gallon UST, was removed on December 14, 1988. This document presents a comprehensive summary of all environmental assessment investigations conducted at the Building 9201-1 Site and the corrective action measures proposed for remediation of subsurface petroleum product contamination identified at the site. This document is written in accordance with the regulatory requirements of the Tennessee Department of Environment and Conservation (TDEC) Rule 1200-1-15-.06(7)

Underground Pumped Hydroelectric Storage (UPHS). Program report, April 1-September 30, 1979. ANL Activity No. 49964

Energy Technology Data Exchange (ETDEWEB)

Blomquist, C.A.; Frigo, A.A.; Tam, S.W.; Clinch, J.M.

1979-10-01

The Argonne National Laboratory Underground Pumped Hydroelectric Storage activities for the second half of FY 1979 are described. Activities include program management and support, subcontract work, and systems studies. Information is given on the preliminary design, hydraulic performance, and cost of high-head, 350-MW capacity, single- and two-stage reversible, Francis-type pump turbines. Similar information is also presented on 350- and 500-MW capacity, multistage, unregulated, reversible, pump turbines. An assessment of the application potential of controlled-flow rate pumps and pump turbines is included. The effects of the charge/discharge ratio of a pumped stoage plant is also discussed.

Scenario of the emerging shift from gasoline to LPG fuelled cars in Ghana: A case study in Ho Municipality, Volta Region

International Nuclear Information System (INIS)

Biscoff, Robert; Akple, Maxwell; Turkson, Richard; Klomegah, Wise

2012-01-01

The use of LPG as automotive fuel is on the increase worldwide. In developing countries such as Ghana, the rudimental way of operating LPG cars is of a national concern since there is no clear cut framework within which they function. This paper presents a scenario of development from conversion of gasoline to LPG fuelling system in cars in Ho, Ghana. Data were collected through survey (100 questionnaires), in-depth interviews (2), Focus Group Discussions (3) and direct observations. The result shows LPG conversion is carried out by the local informally trained mechanics especially for Taxis because of its low consumption resulting in more profit. Conversion takes 1–2 day with an average estimated cost of GH□ 450 cedis ($300). The LPG policy in Ghana focuses on domestic purposes hence the fuel being heavily subsidised. Challenges' being faced by the autogas market in Ghana includes; no clear cut policy, low number of refuelling stations, lack of standard conversion and installation kits and unprofessional LPG installers. In order for government to benefit from LPG as automotive fuel, coherent autogas policy should be formulated ensuring the availability of the LPG with price affordability as in the case of gasoline and diesel. - Highlights: ► Cars are converted to LPG system locally because of economic gains relative to emission reduction. ► LPG fuelled cars makes twice profit as compared to gasoline cars. ► Conversion to LPG system takes 1–2 day with an average cost of GH 450 cedis ($300). ► LPG policy in Ghana focus on domestic purposes not for commercial hence heavily subsidised. ► Ghana Government should formulate clear policy on LPG use in cars.

Far East LPG sales will grow faster than in West

International Nuclear Information System (INIS)

Anon.

1996-01-01

LPG sales through 2010 in regions east of the Suez Canal (East of Suez) will grow at more than twice those in regions west of the canal. East-of-Suez sales will grow at more than 4.0%/year, compared to slightly less than 2.0%/year growth in sales West of Suez. East-of-Suez sales will reach 92 million tons/year (tpy) by 2010, accounting for 39% of the worldwide total. This share was 31% in1995 and only 27% in 1990. LPG sales worldwide will reach 192 million tons in 2000 and 243 million tpy by 2010. In 1995, they were 163 million tons. These are some of the major conclusions of a recent study by Frank R. Spadine, Christine Kozar, and Rudy Clark of New York City-based consultant Poten and Partners Inc. Details of the study are in the fall report ''World Trade in LPG 1990--2010''. This paper discusses demand segments, seaborne balance, Western sources, largest trading region, North American supplies, and other supplies

Spent fuel disposal: is the underground the sole solution?

International Nuclear Information System (INIS)

Nachmilner, L.

1997-01-01

The following 4 major approaches to spent fuel disposal are discussed: permanent storage in an underground repository, reprocessing, partitioning and transmutation, and accelerator driven transmutation. It is concluded that underground disposal will remain the basic option for the near future, although pursuing the other methods is certainly worth while. (P.A.)

Liquefied petroleum gas (LPG) poisoning: report of two cases and review of the literature.

Science.gov (United States)

Fukunaga, T; Yamamoto, H; Tanegashima, A; Yamamoto, Y; Nishi, K

1996-10-25

Two autopsy cases of men who died while connecting a liquefied petroleum gas (LPG) pipe are reported. Their blood concentrations of propane (the main content of LPG) were 0.12 and 3.40 mg/100 g, respectively. The cause of death after exposure of LPG has generally been considered to be asphyxia from hypoxia. The large differences in the blood propane levels found here and reported in the literature, however, suggest that direct toxic effects of propane poisoning may be the cause of death in some cases. Propane concentrations and the cause of death are reviewed and discussed.

Integrated underground gas storage of CO2 and CH4 to decarbonize the "power-to-gas-to-gas-to-power" technology

Science.gov (United States)

Kühn, Michael; Streibel, Martin; Nakaten, Natalie; Kempka, Thomas

2014-05-01

Massive roll-out of renewable energy production units (wind turbines and solar panels) leads to date to excess energy which cannot be consumed at the time of production. So far, long-term storage is proposed via the so called 'power-to-gas' technology. Energy is transferred to methane gas and subsequently combusted for power production - 'power-to-gas-to-power' (PGP) - when needed. PGP profits from the existing infrastructure of the gas market and could be deployed immediately. However, major shortcoming is the production of carbon dioxide (CO2) from renewables and its emission into the atmosphere. We present an innovative idea which is a decarbonised extension of the PGP technology. The concept is based on a closed carbon cycle: (1) Hydrogen (H2) is generated from renewable energy by electrolysis and (2) transformed into methane (CH4) with CO2 taken from an underground geological storage. (3) CH4 produced is stored in a second storage underground until needed and (4) combusted in a combined-cycled power plant on site. (5) CO2 is separated during energy production and re-injected into the storage formation. We studied a show case for the cities Potsdam and Brandenburg/Havel in the Federal State of Brandenburg in Germany to determine the energy demand of the entire process chain and the costs of electricity (COE) using an integrated techno-economic modelling approach (Nakaten et al. 2014). Taking all of the individual process steps into account, the calculation shows an overall efficiency of 27.7 % (Streibel et al. 2013) with total COE of 20.43 euro-cents/kWh (Kühn et al. 2013). Although the level of efficiency is lower than for pump and compressed air storage, the resulting costs are similar in magnitude, and thus competitive on the energy storage market. The great advantage of the concept proposed here is that, in contrast to previous PGP approaches, this process is climate-neutral due to CO2 utilisation. For that purpose, process CO2 is temporally stored in an

CdO necklace like nanobeads decorated with PbS nanoparticles: Room temperature LPG sensor

Energy Technology Data Exchange (ETDEWEB)

Sonawane, N.B. [Department of Physics, School of Physical Sciences, North Maharashtra University, Jalgaon, 425001 M.S. (India); K.A.M.P. & N.K.P. Science College, Pimpalner, Sakri, Dhule, M.S. (India); Baviskar, P.K. [Department of Physics, School of Physical Sciences, North Maharashtra University, Jalgaon, 425001 M.S. (India); Ahire, R.R. [S.G. Patil Science, Sakri, Dhule, M.S. (India); Sankapal, B.R., E-mail: brsankapal@gmail.com [Nano Materials and Device Laboratory, Department of Applied Physics, Visvesvaraya National Institute of Technology, South Ambazari Road, Nagpur, 440010 M.S. (India)

2017-04-15

Simple chemical route has been employed to grow interconnected nanobeads of CdO having necklace like structure through air annealing of cadmium hydroxide nanowires. This nanobeads of n-CdO with high surface area has been decorated with p-PbS nanoparticles resulting in the formation of nano-heterojunction which has been utilized effectively as room temperature liquefied petroleum gas (LPG) sensor. The room temperature gas response towards C{sub 2}H{sub 5}OH, Cl{sub 2}, NH{sub 3}, CO{sub 2} and LPG was investigated, among which LPG exhibits significant response. The maximum gas response of 51.10% is achieved with 94.54% stability upon exposure of 1176 ppm concentration of LPG at room temperature (27 °C). The resulting parameters like gas response, response and recovery time along with stability studies has been studied and results are discussed herein. - Highlights: • Conversion of Cd(OH){sub 2} nanowires to CdO nanonecklace by air annealing at 290 °C. • Decoration of PbS nanoparticles over CdO nanobeads by SILAR method. • Formation of n-CdO/p-PbS nano-heterojunction as room temperature LPG sensor. • Maximum gas response of 51.10% with 94.54% stability.

LPG in the Totalfina-Elf merger; Le GPL dans la fusion Totalfina-Elf

Energy Technology Data Exchange (ETDEWEB)

Anon.

2000-04-01

Elf Aquitaine's take-over by TotalFina was approved on February 9, by the European Commission, with substantial changes to the project initially submitted. One of the main changes involves the sale of Elf Antargaz and of a part of Elf's associated LPG logistics. Rumors say that a dozen of potential buyers were on the ranks in February to acquire this company which is the second French LPG marketer. The sale seems to question the LPG scheme set by TotalFina at the end of 1999. We published in our previous issue this scheme which was designed to give a larger span to the product, with its own management apart from other specialties. (authors)

LPG consumption in the long term: supply, pricing demand with particular reference to the petrochemical sector

International Nuclear Information System (INIS)

Shammas, P.

1996-01-01

Supply of LPG is forecast to grow over the next decade from the present level of 180 million t/y to about 185-190 million t/y, depending on demand in Asia which is rising rapidly and on new LPG export projects. Most of the increase in supply will come from new gas and crude oil production, from new LPG ventures, and from refineries reducing the n-butane content of motor gasoline. Pricing will remain volatile as a result of crude oil price volatility, variations in the winter weather in the Northern Hemisphere, and as result of competition between ethane, PPG, naphtha and condensate as ethylene cracker feedstocks. Demand for LPG in OECD countries will continue to show steady growth. The increase in demand will be more rapid in the relatively less developed OECD countries, as the trend in Spain has shown in recent years. Provided that the LPG price is competitive, demand in China, South-East Asia and the Indian sub-continent could grow beyond current projections. Consumption in these countries will depend on the installation of distribution facilities and the rate at which LPG can substitute for traditional fuels and kerosene as well as compete for limited disposable incomes. (author)

LPG sensing characteristics of electrospray deposited SnO2 nanoparticles

International Nuclear Information System (INIS)

Gürbüz, Mevlüt; Günkaya, Göktuğ; Doğan, Aydın

2014-01-01

Highlights: • SnO 2 nanopowder was deposited on conductive substrates using ESD technique. • Solution flow rate, coating time, substrate–nozzle distance and solid/alcohol ratio were studied to optimize SnO 2 film structure. • The gas sensing properties of tin oxide films were investigated using LPG. • The sensitivity of the films was increased with operating temperature. • The best sensitivity was observed for 20 LEL LPG at 450 °C operating temperature. - Abstract: In this study, SnO 2 films were fabricated on conductive substrate such as aluminum and platinum coated alumina using electro-spray deposition (ESD) method for gas sensor applications. Solution flow rate, coating time, substrate–nozzle distance and solid/alcohol ratio were studied to optimize SnO 2 film structure. The morphology of the deposited films was characterized by stereo and scanning electron microscopy (SEM). The gas sensing properties of tin oxide films were investigated using liquid petroleum gas (LPG) for various lower explosive limit (LEL). The results obtained from microscopic analyses show that optimum SnO 2 films were evaluated at flow rate of 0.05 ml/min, at distance of 6 cm, for 10 min deposition time, for 20 gSnO 2 /L ethanol ratio and at 7 kV DC electric field. By the results obtained from the gas sensing behavior, the sensitivity of the films was increased with operating temperature. The films showed better sensitivity for 20 LEL LPG concentration at 450 °C operating temperature

Multinational underground nuclear parks

Energy Technology Data Exchange (ETDEWEB)

Myers, C.W. [Nuclear Engineering and Nonproliferation Division, Los Alamos National Laboratory, MS F650, Los Alamos, NM 87544 (United States); Giraud, K.M. [Wolf Creek Nuclear Operating Corporation, 1550 Oxen Lane NE, P.O. Box 411, Burlington, KS 66839-0411 (United States)

2013-07-01

Newcomer countries expected to develop new nuclear power programs by 2030 are being encouraged by the International Atomic Energy Agency to explore the use of shared facilities for spent fuel storage and geologic disposal. Multinational underground nuclear parks (M-UNPs) are an option for sharing such facilities. Newcomer countries with suitable bedrock conditions could volunteer to host M-UNPs. M-UNPs would include back-end fuel cycle facilities, in open or closed fuel cycle configurations, with sufficient capacity to enable M-UNP host countries to provide for-fee waste management services to partner countries, and to manage waste from the M-UNP power reactors. M-UNP potential advantages include: the option for decades of spent fuel storage; fuel-cycle policy flexibility; increased proliferation resistance; high margin of physical security against attack; and high margin of containment capability in the event of beyond-design-basis accidents, thereby reducing the risk of Fukushima-like radiological contamination of surface lands. A hypothetical M-UNP in crystalline rock with facilities for small modular reactors, spent fuel storage, reprocessing, and geologic disposal is described using a room-and-pillar reference-design cavern. Underground construction cost is judged tractable through use of modern excavation technology and careful site selection. (authors)

A comparative study of gas-gas miscibility processes in underground gas storage reservoirs

Energy Technology Data Exchange (ETDEWEB)

Rafiee, M.M.; Schmitz, S. [DBI - Gastechnologisches Institut gGmbH, Freiberg (Germany)

2013-08-01

Intermixture of gases in underground gas reservoirs have had great weight for natural gas storage in UGS projects with substitution of cushion gas by inert gases or changing the stored gas quality or origin, as for the replacement of town gas by natural gas. It was also investigated during the last years for Enhanced Gas Recovery (EGR) and Carbon Capture and Storage (CCS) projects. The actual importance of its mechanisms is discussed for the H{sub 2} storage in Power to Gas to Power projects (PGP). In these approaches miscibility of the injected gas with the gas in place in the reservoir plays an important role in the displacement process. The conditions and parameters for the gas-gas displacement and mixing have been investigated in previous projects, as e.g. the miscibility of CO{sub 2} with natural gas (CLEAN). Furthermore the miscibility process of town gas with natural gas and sauer gas with sweet gas were also previously measured and compared in laboratory. The objective of this work is to investigate the miscibility of H{sub 2} injection into natural gas reservoirs using a compositional and a black oil reservoir simulator. Three processes of convection, dispersion and diffusion are considered precisely. The effect of gas miscibility is studied for both simulators and the results are compared to find optimum miscibility parameters. The findings of this work could be helpful for further pilot and field case studies to predict and monitor the changes in gas composition and quality. In future this monitoring might become more important when PGP together with H{sub 2}-UGS, as storage technology, will help to successfully implement the change to an energy supply from more renewable sources. Similarly the method confirms the use of the black oil simulator as an alternative for gas-gas displacement and sequestration reservoir simulation in comparison to the compositional simulator. (orig.)

Analysis of tank safety with propane-butane on LPG distribution station

Directory of Open Access Journals (Sweden)

Krzysiak Zbigniew

2017-12-01

Full Text Available An analysis of the risk of failure in the safety valve – tank with propane-butane (LPG system has been conducted. An uncontrolled outflow of liquid LPG, caused by a failure of the above mentioned system has been considered as a threat. The main research goal of the study is the hazardous analysis of propane-butane gas outflow for the safety valve – LPG tank system. The additional goal is the development of an useful method to fast identify the hazard of a mismatched safety valve. The results of the research analysis have confirmed that safety valves are basic protection of the installation (tank against failures that can lead to loss of life, material damage and further undesired costs of their unreliability. That is why a new, professional computer program has been created that allows for the selection of safety valves or for the verification of a safety valve selection in installations where any technical or technological changes have been made.

Transient evaluation for LPG and oil pipelines

Energy Technology Data Exchange (ETDEWEB)

Meliande, Patricia; Do Nascimento, Elson Antonio; Fernandes Lacerda, Rogerio [Federal Fluminense University, Niteroi, RJ (Brazil)

2010-07-01

In the last decades, the offshore industry has expanded thanks to the development of equipment for subsea operation. In such installations, protection equipment can be adapted to the installation's design in order to avoid surge pressure effects and ensure safety and integrity of the system, predicting transient effect is therefore very important. The purpose of this study is to predict the surge pressure on refrigerated LPG and gasoline pipelines during unpredicted closure of valves. Flowmaster software was used to carry out the simulations and its results were then validated with a methodology that applied the characteristics method based on Wylie and Streeter assumptions. Results showed that surge pressures during transient effect for both refrigerated LPG and Gasoline pipeline systems were less than the maximum allowable operating pressure and therefore no control dispositive installations are geeded. This study showed that the use of these computer models can ensure the optimization of the system and provide cost effective solutions.

Underground nuclear energy complexes - technical and economic advantages

Energy Technology Data Exchange (ETDEWEB)

Myers, Carl W [Los Alamos National Laboratory; Kunze, Jay F [IDAHO STATE UNIV; Giraud, Kellen M [BABECOCK AND WILCOX; Mahar, James M [IDAHO STATE UNIV

2010-01-01

Underground nuclear power plant parks have been projected to be economically feasible compared to above ground instalIations. This paper includes a thorough cost analysis of the savings, compared to above ground facilities, resulting from in-place entombment (decommissioning) of facilities at the end of their life. reduced costs of security for the lifetime of the various facilities in the underground park. reduced transportation costs. and reduced costs in the operation of the waste storage complex (also underground). compared to the fair share of the costs of operating a national waste repository.

Viewing Systems for Large Underground Storage Tanks

International Nuclear Information System (INIS)

Heckendorn, F.M.; Robinson, C.W.; Anderson, E.K.; Pardini, A.F.

1996-01-01

Specialized remote video systems have been successfully developed and deployed in a number of large radiological Underground Storage Tanks (USTs)that tolerate the hostile tank interior, while providing high resolution video to a remotely located operator. The deployment is through 100 mm (4 in) tank openings, while incorporating full video functions of the camera, lights, and zoom lens. The usage of remote video minimizes the potential for personnel exposure to radiological and hazardous conditions, and maximizes the quality of the visual data used to assess the interior conditions of both tank and contents. The robustness of this type of remote system has a direct effect on the potential for radiological exposure that personnel may encounter. The USTs typical of the Savannah River and Hanford Department Of Energy - (DOE) sites are typically 4.5 million liter (1.2 million gal) units under earth. or concrete overburden with limited openings to the surface. The interior is both highly contaminated and radioactive with a wide variety of nuclear processing waste material. Some of the tanks are -flammable rated -to Class 1, Division 1,and personnel presence at or near the openings should be minimized. The interior of these USTs must be assessed periodically as part of the ongoing management of the tanks and as a step towards tank remediation. The systems are unique in their deployment technology, which virtually eliminates the potential for entrapment in a tank, and their ability to withstand flammable environments. A multiplicity of components used within a common packaging allow for cost effective and appropriate levels of technology, with radiation hardened components on some units and lesser requirements on other units. All units are completely self contained for video, zoom lens, lighting, deployment,as well as being self purging, and modular in construction

Local health care system utilizing the LPG (liquid propane gas) network.

Science.gov (United States)

Umemoto, T; Hoshi, H; Tsuda, M; Horio, S; Itou, N; Neriki, T

1998-07-01

JAC's LPG monitoring network system is mainly provided in mountain villages. However, by using this system, it will be possible to start a Digital Network Program for the Elderly while maintaining superior economic feasibility and public benefit using existing information infrastructures. This project also has the capabilities for the creation of a fire/disaster monitoring system, as well as a health care system by using conventional LPG monitoring systems. Telemedicine is an option for the future, as well, by connecting medical equipment and a tele-conferencing system.

PRODUCTION OF HYDROGEN FROM THE STEAM AND OXIDATIVE REFORMING OF LPG: THERMODYNAMIC AND EXPERIMENTAL STUDY

Directory of Open Access Journals (Sweden)

P. P. Silva

2015-09-01

Full Text Available AbstractThe objective of this paper was to use a thermodynamic analysis to find operational conditions that favor the production of hydrogen from steam and oxidative reforming of liquefied petroleum gas (LPG. We also analyzed the performance of a catalyst precursor, LaNiO3, in order to compare the performance of the obtained catalyst with the thermodynamic equilibrium predictions. The results showed that it is possible to produce high concentrations of hydrogen from LPG reforming. The gradual increase of temperature and the use of high water concentrations decrease the production of coke and increase the formation of H2. The reaction of oxidative reforming of LPG was more suitable for the production of hydrogen and lower coke formation. Furthermore the use of an excess of water (H2O/LPG =7.0 and intermediate temperatures (973 K are the most suitable conditions for the process.

LPG and NH3 sensing characteristics of DC electrochemically deposited Co3O4 films

Science.gov (United States)

Shelke, P. N.; Khollam, Y. B.; Gunjal, S. D.; Koinkar, P. M.; Jadkar, S. R.; Mohite, K. C.

2015-03-01

Present communication reports the LPG and NH3 sensing properties of Co3O4 films prepared on throughly cleaned stainless steel (SS) and copper (CU) substrates by using DC electrochemical deposition method followed by air annealing at 350°C/2 h. The resultant films are characterized by using X-ray diffraction (XRD), Raman spectroscopy and scanning electron microscopy (SEM). The LPG and NH3 gas sensing properties of these films are measured at room temperature (RT) by using static gas sensing system at different concentrations of test gas ranging from 25 ppm to 350 ppm. The XRD and Raman spectroscopy studies clearly indicated the formation of pure cubic spinel Co3O4 in all films. The LPG and NH3 gas sensing properties of films showed (i) the increase in sensitivity factor (S.F.) with gas concentrations and (ii) more sensibility to LPG as compared to NH3 gas. In case of NH3 gas (conc. 150 ppm) and LPG gas (conc. 60 ppm) sensing, the maximum S.F. = 270 and 258 are found for the films deposited on CU substrates, respectively. For all films, the response time (3-5 min.) is found to be much higher than the recovery time (30-50 sec). For all films, the response and recovery time are found to be higher for LPG as compared to NH3 gas. Further, repeatability-reproducibility in gas sensing properties is clearly noted by analysis of data for number of cycles recorded for all films from different set of depositions.

Assessment of the potential of the Mainfranken region, northern Bavaria, for underground storage of geothermal energy; Erkundung des regionalen Potentials fuer die Untergrundspeicherung thermischer Energie in Mainfranken (UTEM)

Energy Technology Data Exchange (ETDEWEB)

Barthel, R; Heinrichs, G; Udluft, P [Lehr- und Forschungsbereich Hydrogeologie und Umwelt, Inst. fuer Geologie, Univ. Wuerzburg (Germany); Ebert, H P; Fricke, J [Abt. Waermedaemmung/Waermetransport, Bayerisches Zentrum fuer Angewandte Energieforschung e.V., Wuerzburg (Germany)

1997-12-01

The following paper presents a research project that is planned as a cooperation of the Geological Institute, University of Wuerzburg and the Bavarian Center of Applied Energy Research. In this project the potentials for underground thermal energy storage will be investigated in the region of Mainfranken, Northern Bavaria (Main = the river `Main`, Franken = Franconia). All aspects of underground storage will be studied with respect to the specific geographical and geological situation of the area. The study will provide a detailed map of possible storage sites, from which several case studies and at least one demonstration projects will result. (orig.) [Deutsch] Im vorliegenden Beitrag wird ein Forschungsprojekt vorgestellt, das gemeinsam vom Institut fuer Geologie der Universitaet Wuerzburg und dem Zentrum fuer Angewandte Energieforschung in Bayern geplant wird. Ziel des Projekts ist die Erkundung des Potentials fuer die Untergrundspeicherung thermischer Energie in Mainfranken (Nordbayern). Alle Aspekte der Untergrundspeicherung werden regionalspezifisch betrachtet. Neben der Erstellung differenzierter Karten geeigneter Standorte sind Fallstudien und Demonstrationsprojekte in Planung. (orig.)

Underground storage tank - Integrated Demonstration Technical Task Plan master schedule

International Nuclear Information System (INIS)

Johnson, C.M.

1994-08-01

This document provides an integrated programmatic schedule (i.e., Master Schedule) for the U.S. Department of Energy (DOE) Underground Storage Tank-Integrated Demonstration (UST-ID) Program. It includes top-level schedule and related information for the DOE Office of Technology Development (EM-50) UST-ID activities. The information is based upon the fiscal year (FY) 1994 technical task plans (TTPS) and has been prepared as a baseline information resource for program participants. The Master Schedule contains Level 0 and Level 1 program schedules for the UST-ID Program. This document is one of a number of programmatic documents developed to support and manage the UST-ID activities. It is composed of the following sections: Program Overview - provides a summary background of the UST-ID Program. This summary addresses the mission, scope, and organizational structure of the program; Activity Description - provides a programmatic description of UST-ID technology development activities and lists the key milestones for the UST-ID systems. Master Schedules - contains the Level 0 and Level 1 programmatic schedules for the UST-ID systems. References - lists the UST-ID programmatic documents used as a basis for preparing the Master Schedule. The appendixes contain additional details related to site-specific technology applications

Energy poverty reduction by fuel switching. Impact evaluation of the LPG conversion program in Indonesia

NARCIS (Netherlands)

Andadari, R.K.; Mulder, P.; Rietveld, P.

2014-01-01

In low- and middle-income countries, Liquefied Petroleum Gas (LPG) can be an attractive alternative to the widespread use of traditional kerosene. Not only is LPG a relatively clean, safe and cost-effective fuel for households, its large-scale adoption also reduces the heavy burden of kerosene

Vitrification of underground storage tanks: Technology development, regulatory issues, and cost analysis

International Nuclear Information System (INIS)

Tixier, J.S.; Corathers, L.A.; Anderson, L.D.

1992-03-01

In situ vitrification (ISV), developed by the Pacific Northwest Laboratory (PNL) for the US Department of Energy (DOE), is a thermal treatment process for the remediation of hazardous, radioactive, or mixed waste sites. The process has been broadly patented both domestically and abroad. Since the inception of ISV in 1980, developmental activities have been focused on applications to contaminated soils, and more recently the potential for application to buried wastes and underground structures (tanks). Research performed to date on the more advanced ISV applications (i.e., application to buried wastes and underground tanks) shows that significant technical and economic potential exists for using ISV to treat buried wastes and underground structures containing radionuclides and/or hazardous constituents. Present ISV applications are directed to the treatment of contaminated soils; the likelihood of using ISV to treat underground tanks depends on the resolution of significant technical and institutional issues related to this advanced application. This paper describes the ISV process and summarizes the technical progress of underground tank vitrification (UTV), discusses pertinent regulatory issues facing the use of UTV, and presents the potential cost of UTV relative to other remedial action alternatives

Early structure of LPG partially premixed conically stabilized flames

KAUST Repository

Elbaz, Ayman M.

2013-01-01

This paper presents experimental investigation of LPG partially premixed turbulent flames stabilized within a conical nozzle burner under constant degree of partial premixing. The stability limits and mean flame structure are presented based

Underground storage tanks cause environmental chaos

International Nuclear Information System (INIS)

Cruver, P.C.

1991-01-01

This paper reports that during the 1950s and the subsequent three decades, petroleum products were stored in single-walled steel underground tanks; an out-of-sight, out-of-mind philosophy prevailed. Unfathomable amounts of toxic petroleum products leaking into the nation's ground water supplies has prompted enactment of recent and much needed legislation and regulation to remedy this major problem. Is the public aware of this serious ecological imbroglio? No, not as yet; except for the closing of many rural service stations and the plethora of dug-up, exposed tanks at urban stations, one could never imagine the severity of this debacle confronting the petroleum industry and the nation's environment

KAJIAN TEKNIS DAN EKONOMIS PENGGUNAAN DUAL FUEL SYSTEM (LPG-SOLAR PADA MESIN DIESEL KAPAL NELAYAN TRADISIONAL

Directory of Open Access Journals (Sweden)

Imam Pujo Mulyatno

2013-06-01

Full Text Available Pengembangan bahan bakar alternatif dalam rangka mengurangi ketergantungan terhadap bahan bakar minyak (BBM, telah menjadi agenda penting  pemerintah. Penggunaan LPG (Liquefied Petrolium Gas pada mesin diesel kapal nelayan tradisional didasarkan pada keberhasilan penggunaan LPG pada kendaraan-kendaraan darat. Penggunaan LPG pada mesin diesel dilakukan secara dual fuel. Penelitian dual fuel system pada mesin diesel kapal nelayan tradisional bertujuan untuk mengetahui pengaruh penggunaan bahan bakar dual fuel terhadap kinerja mesin dan sistem penggeraknya, meliputi konsumsi bahan bakar, daya, kecepatan kapal, serta efisiensi pada sistem penggerak kapal. Penelitian dilakukan dengan menggunakan DongFeng ZS-1100 dengan tiga putaran mesin yang berbeda yaitu 1000rpm, 1250 rpm dan 1500 rpm. Berdasarkan hasil penelitian ini, penggunaan LPG secara dual fuel mampu menggantikan konsumsi solar hingga 71% dari konsumsi solar seluruhnya selama satu jam. Komposisi LPG yang dihasilkan mencapai lebih dari 60%  dari total pemakaian bahan bakar saat dual fuel. Kecepatan dan jarak tempuh saat menggunakan solar seluruhnya mencapai 5% lebih tinggi dibandingkan dual fuel. Daya dan torsi saat menggunakan dual fuel mencapai 9,8 % lebih tinggi dibandingkan solar seluruhnya. Penggunaan dual fuel mampu mengurangi biaya operasional penangkapan ikan hingga 24,6%, namun dengan waktu tempuh 1,3% lebih lama dari solar seluruhnya. Efisiensi propulsi solar seluruhnya 6% lebih besar dibandingkan efisiensi propulsi dual fuel.

Effect of variation in LPG composition on emissions and performance in a dual fuel diesel engine

Energy Technology Data Exchange (ETDEWEB)

H.E. Saleh [Mattaria, Helwan University, Cairo (Egypt). Department of Mechanical Power Engineering

2008-10-15

This paper investigates the effect of variation in LPG composition on emissions and performance characteristics in a dual fuel engine run on diesel fuel and five gaseous fuel of LPG with different composition. To quantify the best LPG composition for dual fuel operation especially in order to improve the exhaust emissions quality while maintaining high thermal efficiency comparable to a conventional diesel engine, a two-cylinder, naturally aspirated, four-stroke, DI diesel engine converted to run as pilot-injected dual fuel engine. The tests and data collection were performed under various conditions of load at constant engine speed. From the results, it is observed that the exhaust emissions and fuel conversion efficiency of the dual fuel engine are found to be affected when different LPG composition is used as higher butane content lead to lower NOx levels while higher propane content reduces CO levels. Fuel No. 3 (70% propane, 30% butane) with mass fraction 40% substitution of the diesel fuel was the best LPG composition in the dual fuel operation except that at part loads. Also, tests were made for fuel No. 3-diesel blend in the dual fuel operation at part loads to improve the engine performances and exhaust emissions by using the Exhaust Gas Recirculation (EGR) method. 26 refs., 15 figs., 5 tabs.

Direct injection of gaseous LPG in a two-stroke SI engine for improved performance

International Nuclear Information System (INIS)

Pradeep, V.; Bakshi, Shamit; Ramesh, A.

2015-01-01

Improvements in a two-stroke, spark-ignition (2S–SI) engine can be realized by curtailing short-circuiting losses effectively through direct injection of the fuel. Liquefied petroleum gas (LPG) is an alternative transportation fuel that is used in several countries. However, limited information is available on LPG fuelled direct injected engines. Hence, there is a need to study these systems as applied to 2S–SI engines in order to bring out their potential benefits. A manifold injected 2S–SI engine is modified for direct injection of LPG, in gaseous form, from the cylinder head. This engine is evaluated for performance, emission and combustion. Evaluation at various throttle positions and constant speed showed that this system can significantly improve the thermal efficiency and lower the hydrocarbon (HC) emissions. Up to 93% reduction in HC emissions and improved combustion rates are observed compared to the conventional manifold injection system with LPG. CO emissions are higher and peak NO emissions are lower with this system due to the presence of richer in–cylinder trapped mixtures and charge stratification. This system can operate with similar injection timings at different throttle positions which make electronic control simpler. It can work with low injection pressures in the range of 4–5 bars. All these advantages are attractive for commercial viability of this engine. - Highlights: • Energy saving, low pressure, direct gaseous LPG injection in engine. • Significant reduction in HC emissions at all operating conditions. • No significant changes in injection timings for different throttle positions.

LPG Maruziyeti Sonucu Ölüm Olgu Sunumu

Directory of Open Access Journals (Sweden)

Ayşe Kurtuluş

2009-12-01

Full Text Available LPG (liquefied petrol gases- sıvılaştırılmış petrol gazları, basınç altında sıvı hale getirilmiş hafif alifatik hidrokarbon olan bütan (C4H10 ve propan (CjHg karışımından oluşan renksiz ve hafif bir kokuya sahip bir gazdır. LPG kaynaklı ölümler genellikle kazaya bağlı olarak karşımıza çıkmakta ve intihar daha seyrek görülmektedir. Bütan ve propana bağlı ölümün asfiksi, vagal inhibisyon, respiratuar depresyon ve aritmiler olmak üzere dört mekanizma ile meydana gelebileceği belirtilmektedir. Bu çalışmada, vücudunun tamamını battaniye ile örtüp, açık mutfak tüpünden uzanan hortumun ucunu battaniyenin altına sokarak özel düzenek hazırlayan ve bu düzenekle yatağında intihar eden 64 yaşmda bir erkek olgu sunulmuştur. Seyrek görülen bu olguya ait bulgular, literatür eşliğinde tartışılmıştır. Anahtar kelimeler:LPG, bütan, propan, intihar

Particle and carbon dioxide emissions from passenger vehicles operating on unleaded petrol and LPG fuel

International Nuclear Information System (INIS)

Ristovski, Z.D.; Jayaratne, E.R.; Morawska, L.; Ayoko, G.A.; Lim, M.

2005-01-01

A comprehensive study of the particle and carbon dioxide emissions from a fleet of six dedicated liquefied petroleum gas (LPG) powered and five unleaded petrol (ULP) powered new Ford Falcon Forte passenger vehicles was carried out on a chassis dynamometer at four different vehicle speeds-0 (idle), 40, 60, 80 and 100 km h -1 . Emission factors and their relative values between the two fuel types together with a statistical significance for any difference were estimated for each parameter. In general, LPG was found to be a 'cleaner' fuel, although in most cases, the differences were not statistically significant owing to the large variations between emissions from different vehicles. The particle number emission factors ranged from 10 11 to 10 13 km -1 and was over 70% less with LPG compared to ULP. Corresponding differences in particle mass emission factor between the two fuels were small and ranged from the order of 10 μg km -1 at 40 to about 1000 μg km -1 at 100 km h -1 . The count median particle diameter (CMD) ranged from 20 to 35 nm and was larger with LPG than with ULP in all modes except the idle mode. Carbon dioxide emission factors ranged from about 300 to 400 g km -1 at 40 km h -1 , falling with increasing speed to about 200 g km -1 at 100 km h -1 . At all speeds, the values were 10% to 18% greater with ULP than with LPG

Investigating the influences of liquid LPG injection on spark ignition (SI engine

Directory of Open Access Journals (Sweden)

Tukiman Mohd Mustaqim

2017-01-01

Full Text Available Liquefied petroleum gas (LPG is one of the alternative fuels that becoming popular to be use in spark ignition engine (SI. This paper briefly presents the influence of energy content to the engine output of 1.6L SI engine of Proton Gen 2. The engine was coupled to a chassis dynamometer and few related apparatus were employed in determine the engine behavior. All data collected were illustrated in graph for further analysis. The engine shows comparable engine output, however, the engine requires some tuning in order to fully utilize the energy content of LPG.

Kajian Eksperimental Perbandingan Performansi Mesin Otto Bahan Bakar Premium dengan Bahan Bakar LPG

OpenAIRE

Sitorus, Jefferson

2013-01-01

The decreasing availability of fossil fuels led to a variety of ideas how to solve this problem. LPG (Liquefied petroleum gas) is one alternative fuel that can be used in trending engine, one of which is a gasoline engine generator sets in 4-stroke. By modifying the carburetor so the engine can work as when using gasoline. Although the performance of the machine tends to not give optimal results such as engine performance when using gasoline, but has the advantage of LPG fuel, the emissions p...

96/97 statistics of natural gas industry in France

International Nuclear Information System (INIS)

1998-01-01

This documents presents an overview of the gases market in France (natural gas, LPG, methane, etc..). Details about uses, resources, foreign supplies, intervening parties, transportation and storage facilities are given for the natural gas sector. After a presentation of the gas industry conjuncture in 1996 and a general presentation of the French gas industry, the main economical data are presented as tables, diagrams and graphics: combustible gases (resources and uses, domestic production and imports, regional and industrial distribution and consumption..), and gas distribution networks (resources, exchanges, transformations, sectoral and seasonal analysis of sales, installations, industrial consumption by sector and region, pipelines, underground storage facilities, LNG terminal and storage facilities, tanker-ships, personnel). (J.S.)

p-PEDOT:PSS as a heterojunction partner with n-ZnO for detection of LPG at room temperature

Energy Technology Data Exchange (ETDEWEB)

Ladhe, R.D. [Thin Film and Nano Science Laboratory, Department of Physics, School of Physical Sciences, North Maharashtra University, Jalgaon 425 001 (M.S.) (India); Gurav, K.V. [Department of Materials Science and Engineering, Chonnam National University, Gwangju 500-757 (Korea, Republic of); Pawar, S.M. [Solar Cell Laboratory, LG Components R and D Center, 1271, Sa-Dong, Sanggrok-gu, Ansan-si, Gyeonggi-do 426-791 (Korea, Republic of); Kim, J.H. [Department of Materials Science and Engineering, Chonnam National University, Gwangju 500-757 (Korea, Republic of); Sankapal, B.R., E-mail: brsankapal@rediffmail.com [Thin Film and Nano Science Laboratory, Department of Physics, School of Physical Sciences, North Maharashtra University, Jalgaon 425 001 (M.S.) (India)

2012-02-25

Highlights: Black-Right-Pointing-Pointer Formation of heterojunction n-ZnO and p-PEDOT:PSS at room temperature (27 Degree-Sign C). Black-Right-Pointing-Pointer Use of this heterojunction as room temperature LPG sensor. Black-Right-Pointing-Pointer Remarkable gas response with good stability of the sensing device. Black-Right-Pointing-Pointer Use of heterojunction could offer cost-effective LPG sensor that is ecological-friendly. Black-Right-Pointing-Pointer The mass production using scalable room temperature chemical deposition process. - Abstract: Investigation towards the performance of room temperature (27 Degree-Sign C) liquefied petroleum gas (LPG) sensor based on the heterojunction between p-PEDOT:PSS and n-type ZnO is reported. The junction was developed by using chemically deposited ZnO film on to fluorine doped tin oxide (FTO) coated glass substrate followed by coating of thin slurry layer of PEDOT:PSS by using spin coating technique. Both these methods are simple, inexpensive and suitable for large area applications. Different characterization techniques were used to characterize structural, surface morphological and compositional of the material deposited. LPG sensing behavior of the heterojunction was studied at room temperature along with the stability studies. At room temperature, the heterojunction showed 58.8% sensitivity upon exposure to 1000 ppm of LPG with good response and recovery time like 225 s and 190 s, respectively. Furthermore, the LPG sensor reported is cost-effective, user friendly, and easy to fabricate using low cost chemical methods at room temperature.

Location of leaks in pressurized underground pipelines

International Nuclear Information System (INIS)

Eckert, E.G.; Maresca, J.W. Jr.

1993-01-01

Millions of underground storage tanks (UST) are used to store petroleum and other chemicals. The pressurized underground pipelines associated with USTs containing petroleum motor fuels are typically 2 in. in diameter and 50 to 200 ft in length. These pipelines typically operate at pressures of 20 to 30 psi. Longer lines, with diameters up to 4 in., are found in some high-volume facilities. There are many systems that can be used to detect leaks in pressurized underground pipelines. When a leak is detected, the first step in the remediation process is to find its location. Passive-acoustic measurements, combined with advanced signal-processing techniques, provide a nondestructive method of leak location that is accurate and relatively simple, and that can be applied to a wide variety of pipelines and pipeline products

Effect of initialization time on application potentiality of a ZnO thin film based LPG sensor

Directory of Open Access Journals (Sweden)

Parta Mitra

2009-09-01

Full Text Available A prototype electronic LPG (Liquid Petroleum Gas sensor based on zinc oxide (ZnO film has been fabricated. The objective of the present work was to investigate the importance of initialization time (also called warm-up time on the application potentiality of the ZnO based alarm. The role of sensor geometry on initialization time is presented. The electronic circuitry of the prototype LPG device alarm is discussed. It is shown that that the initialization time depends on the switch off time (or the time for which the sensor was kept idle. The resistive mode sensors can be fixed at 40% LEL (Lower Explosive Limit of LPG for safe operation.

Earth-covered storage of LPG - Development, construction and operating experiences

International Nuclear Information System (INIS)

Schuldt, P.; Grote, G.

1990-01-01

The paper describes the planning, approval procedures, design, fabrication, site-assembling and the testing of liquefied petroleum gas storage tanks. The practical experience after three years of operation is reported. 8 figs

Waste Isolation Pilot Plant supplementary roof support system underground storage area, Panel 1, Room 1

International Nuclear Information System (INIS)

1991-10-01

WIPP is designed to provide a full-scale facility to demonstrate the technical and operational principles for permanent isolation of defense-generated transuranic waste. It is also designed to provide a facility in which studies and experiments can be conducted. Bin Scale Tests are being planned as part of the WIPP Test Phase Performance Assessment Program described in the WIPP Test Phase Plan: Performance Assessment (DOE 1990 b). These Tests are anticipated to be conducted over a period of up to seven years. Room 1 of Panel 1 of the Underground Storage Area is to be used as the location of the Bin-Scale Tests to investigate the generation of gas from the waste that is proposed to be stored at the WIPP in the near future. The original design for the waste storage rooms in Panel 1 provided for a limited period of time during which to mine the openings and to emplace waste. Room 1 was initially mined to rough dimensions in 1986. Information obtained from the Site and Preliminary Design Validation (SPDV) program showed that the rooms would remain stable without ground support and that creep closure would not adversely affect equipment clearances during at least five years following excavation

Geomechanical Analysis of Underground Coal Gasification Reactor Cool Down for Subsequent CO2 Storage

Science.gov (United States)

Sarhosis, Vasilis; Yang, Dongmin; Kempka, Thomas; Sheng, Yong

2013-04-01

Underground coal gasification (UCG) is an efficient method for the conversion of conventionally unmineable coal resources into energy and feedstock. If the UCG process is combined with the subsequent storage of process CO2 in the former UCG reactors, a near-zero carbon emission energy source can be realised. This study aims to present the development of a computational model to simulate the cooling process of UCG reactors in abandonment to decrease the initial high temperature of more than 400 °C to a level where extensive CO2 volume expansion due to temperature changes can be significantly reduced during the time of CO2 injection. Furthermore, we predict the cool down temperature conditions with and without water flushing. A state of the art coupled thermal-mechanical model was developed using the finite element software ABAQUS to predict the cavity growth and the resulting surface subsidence. In addition, the multi-physics computational software COMSOL was employed to simulate the cavity cool down process which is of uttermost relevance for CO2 storage in the former UCG reactors. For that purpose, we simulated fluid flow, thermal conduction as well as thermal convection processes between fluid (water and CO2) and solid represented by coal and surrounding rocks. Material properties for rocks and coal were obtained from extant literature sources and geomechanical testings which were carried out on samples derived from a prospective demonstration site in Bulgaria. The analysis of results showed that the numerical models developed allowed for the determination of the UCG reactor growth, roof spalling, surface subsidence and heat propagation during the UCG process and the subsequent CO2 storage. It is anticipated that the results of this study can support optimisation of the preparation procedure for CO2 storage in former UCG reactors. The proposed scheme was discussed so far, but not validated by a coupled numerical analysis and if proved to be applicable it could

Experimental and analytical investigation of thermal coating effectiveness for 3 m3 LPG tanks engulfed by fire

NARCIS (Netherlands)

Landucci, G.; Molag, M.; Reinders, J.; Cozzani, V.

2009-01-01

Two large-scale diesel pool fire engulfment tests were carried out on LPG tanks protected with intumescing materials to test the effectiveness of thermal coatings in the prevention of hot BLEVE accidental scenarios in the road and rail transport of LPG. A specific test protocol was defined to

Products - transport - storage; Produits - transports - stockages

Energy Technology Data Exchange (ETDEWEB)

Anon.

2005-04-15

9 articles are gathered in this data-sheet; they deal with LPG products, transport and storage. Blackmer offers a full line of LPG equipment for the transfer of propane, butane and anhydrous ammonia. Clesse Industries and Gas Equipment Company equip luxury hotels in Dubai and Abu Dhabi. Since 1975 the company FAS Flussiggas-Anlagen Gmbh, Salzgitter - Germany is one of the leading manufacturers of LPG equipment and components for mobile and stationary bulk plants in Europe. The main products are dispensers, pumps, Auto-gas filling stations, vaporizers, loading arms, electronic cylinder filling scales, flanged valves and safety equipment. FAS is certified with 2 process orientated management systems according to DIN EN ISO 9001:2000 and to PED - Module H1 - Category IV. The company supplies all products and services according to the Pressure Equipment Directive 97/23/EC with CE-mark as well according to regulations ATEX, OIML, TUV, PTB... ECII Engineered Controls International/Rego USA is well known as a worldwide leader and designer/manufacturer of LPG and anhydrous ammonia equipment. The 10. of January Per Sture Jenssen retired from Ragasco A.S. Managing Director after 6 years in the company. Oyvind Hamre who has taken over from Mr. Jenssen, is 39 years of age and he has been 10 years with Ragasco, most recently as R and D Manager. Per Sture Jenssen will still be present in the company until summer 2005 to support during the transition. Corken has put in the market two new products: a new valve and a new pump. Impco Technologies announces completion of BRC acquisition. VOC reduction is a common discussion issue in almost all sectors of the oil business and beyond. Each industry sector has a different strategy towards this issue according to its perceived impact on the business. Although largely motivated by the need to satisfy national and international emission standards, the move towards reduction has encouraged equipment manufacturers to develop advanced

Nautical studies for new LPG (Liquefied Petroleum Gases) in Barra do Riacho

Energy Technology Data Exchange (ETDEWEB)

Amorim, Anderson B.A.; Biolchini, Luiz C.A. [Petroleo do Brasil S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil); Antunes, Felippe L. [Petrobras Transporte S/A (TRANSPETRO), Rio de Janeiro, RJ (Brazil); Vieira Neto, Tancredo [Poyry Technology, Sao Paulo, SP (Brazil)

2009-07-01

PETROBRAS is developing projects to increase the natural gas production, supply and allow transportation to the market. LPG and natural gasoline produced in Cacimbas (ES) will be transferred through pipelines to under construction Barra do Riacho Terminal, to be stored and loaded on ships. In Barra do Riacho, a municipality of Aracruz on the northern coast of the Espirito Santo state, a pulp specialized terminal already operates. The new PETROBRAS terminal will monthly load about 30,000 t of refrigerated LPG and 90,000 m{sup 3} of natural gasoline through a new pier with two berths. This pier will be able to receive tankers up to 60,000 dwt. With the challenge to safely maneuver and berth vessels of this size in a restricted area with operating facilities, PETROBRAS developed a basic design with the support of contracted companies to evaluate the minimum area needed to assure operation and design the best location, minimizing wave disturbance over the new jetty as well as over the existing above mentioned berths. This paper presents the port issues analyzed during the basic design of the new marine refrigerated LPG terminal to be located at Barra do Riacho Port. (author)

Underground storage tank management plan, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-01

The Underground Storage Tank (UST) Program at the Oak Ridge Y-12 Plant was established to locate UST systems at the facility and to ensure that all operating UST systems are free of leaks. UST systems have been removed or upgraded in accordance with Tennessee Department of Environment and Conservation (TDEC) regulations and guidance. With the closure of a significant portion of the USTs, the continuing mission of the UST Management Program is to manage the remaining active UST systems and continue corrective actions in a safe regulatory compliant manner. This Program outlines the compliance issues that must be addressed, reviews the current UST inventory and compliance approach, and presents the status and planned activities associated with each UST system. The UST Program provides guidance for implementing TDEC regulations and guidelines for petroleum UST systems. The plan is divided into three major sections: (1) regulatory requirements, (2) active UST sites, and (3) out-of-service UST sites. These sections describe in detail the applicable regulatory drivers, the UST sites addressed under the Program, and the procedures and guidance for compliance.

Underground storage tank management plan, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1997-09-01

The Underground Storage Tank (UST) Program at the Oak Ridge Y-12 Plant was established to locate UST systems at the facility and to ensure that all operating UST systems are free of leaks. UST systems have been removed or upgraded in accordance with Tennessee Department of Environment and Conservation (TDEC) regulations and guidance. With the closure of a significant portion of the USTs, the continuing mission of the UST Management Program is to manage the remaining active UST systems and continue corrective actions in a safe regulatory compliant manner. This Program outlines the compliance issues that must be addressed, reviews the current UST inventory and compliance approach, and presents the status and planned activities associated with each UST system. The UST Program provides guidance for implementing TDEC regulations and guidelines for petroleum UST systems. The plan is divided into three major sections: (1) regulatory requirements, (2) active UST sites, and (3) out-of-service UST sites. These sections describe in detail the applicable regulatory drivers, the UST sites addressed under the Program, and the procedures and guidance for compliance

Does underground storage still require sophisticated studies?

International Nuclear Information System (INIS)

Marsily, G. de

1997-01-01

Most countries agree to the necessity of burying high or medium-level wastes in geological layers situated at a few hundred meters below the ground level. The advantages and disadvantages of different types of rock such as salt, clay, granite and volcanic material are examined. Sophisticated studies are lead to determine the best geological confinement but questions arise about the time for which safety must be ensured. France has chosen 3 possible sites. These sites are geologically described in the article. The final place will be proposed after a testing phase of about 5 years in an underground facility. (A.C.)

Detecting Liquefied Petroleum Gas (LPG) at Room Temperature Using ZnSnO3/ZnO Nanowire Piezo-Nanogenerator as Self-Powered Gas Sensor.

Science.gov (United States)

Fu, Yongming; Nie, Yuxin; Zhao, Yayu; Wang, Penglei; Xing, Lili; Zhang, Yan; Xue, Xinyu

2015-05-20

High sensitivity, selectivity, and reliability have been achieved from ZnSnO3/ZnO nanowire (NW) piezo-nanogenerator (NG) as self-powered gas sensor (SPGS) for detecting liquefied petroleum gas (LPG) at room temperature (RT). After being exposed to 8000 ppm LPG, the output piezo-voltage of ZnSnO3/ZnO NW SPGS under compressive deformation is 0.089 V, much smaller than that in air ambience (0.533 V). The sensitivity of the SPGS against 8000 ppm LPG is up to 83.23, and the low limit of detection is 600 ppm. The SPGS has lower sensitivity against H2S, H2, ethanol, methanol and saturated water vapor than LPG, indicating good selectivity for detecting LPG. After two months, the decline of the sensing performance is less than 6%. Such piezo-LPG sensing at RT can be ascribed to the new piezo-surface coupling effect of ZnSnO3/ZnO nanocomposites. The practical application of the device driven by human motion has also been simply demonstrated. This work provides a novel approach to fabricate RT-LPG sensors and promotes the development of self-powered sensing system.

Emerging risk issues in underground storage of bituminous coal

Energy Technology Data Exchange (ETDEWEB)

Sipila, J.

2013-11-01

This thesis aims to address the root causes and means of prevention, mitigation and other improvements to the challenges from smouldering fires, coal freezing and occupational risk in an underground storage silo built into granite bedrock. In addition, appropriate performance indicators are suggested, and the benefits of the recommended or adopted actions are estimated. The issues and observed incidents demonstrate hazards that are largely classified to represent issues of emerging risk. To reduce the fire risk, successful measures included bottom maintenance door sealing and modified design of silo filling and discharge. The assessed benefits of these actions suggest a payback period of only about 10 days, assuming that, without these measures, a fire like the one in 2008 could occur once in four years. Additional recommendations are made to reduce air flow through the coal bed and near the silo ceiling, and to improve nitrogen purging at the hoppers. Filling with subzero coal can freeze silo drains, resulting in water inflow and further freezing to hamper discharge. As the heat flow is unlike any previously known cases of coal freezing, conventional mitigation e.g. by freeze conditioning agents, would not help. After implementing modified filling procedures for cold coal, no severe freezing cases have occurred. Safety advantages from the automated and remotely controlled operation do not necessarily apply under exceptional circumstances requiring human involvement. As preventive measures, protection has been sought from additional technical barriers and training effort. The rarity of serious incidents is a challenge in demonstrating success, but also emphasizes the importance of using leading (not only lagging) safety performance indicators for measurable safety promotion. In contrast, suitable leading performance indicators of the fire risk have been suggested for deliveries as an index of coal properties and for storage (gas emissions and temperature

Feasibility of underground storage/disposal of noble gas fission products

International Nuclear Information System (INIS)

Winar, R.M.; Trevorrow, L.E.; Steindler, M.J.

1979-08-01

The quantities of 85 Kr that can be released to the environment from nuclear energy production are to be limited after 1983 by Federal regulations. Although procedures for collecting the 85 Kr released in the nuclear fuel cycle have been developed to the point that they are commercially available, procedures for terminal disposal of the collected gas are still being examined for their feasibility. In this work, the possibilities of underground disposal of 85 Kr by several techniques were evaluated. It was concluded that (1) disposal of 85 Kr as a solution in water or other solvents in deep wells would have the major disadvantages of liquid migration and the requirement of extremely large volumes of solvent; (2) disposal as bubbles entrained in cement grout injected underground presents the uncertainty of gaseous migration through permeable solid grout; (3) disposal by injection into abandoned oil fields would be favored by solubility of krypton in residual hydrocarbons, but has the disadvantages that such fields contain numerous shafts offering avenues of escape and also that the fields may be reworked in the future for their hydrocarbon residues; (4) underground retention of 85 Kr injected as a gas may be promising, given the right lithology, through entrapment in interstices between fine sand grains held together by the interfacial tension of wetted surfaces. 9 figures, 5 tables

241-CX-70, 241-CX-71, and 241-CX-72 underground storage tanks at the strontium semiworks facility supplemental information to the Hanford Facility Contingency Plan

International Nuclear Information System (INIS)

Ingle, S.J.

1996-03-01

This document is a unit-specific contingency plan for the underground storage tanks at the Strontium Semiworks Facility and is intended to be used as a supplement to the Hanford Facility Contingency Plan. This unit-specific plan is to be used to demonstrate compliance with the contingency plan requirements of WAC 173-303 for certain Resource Conservation and Recovery Act of 1976 (RCRA) waste management units. Radioactive material is contained in three underground storage tanks: 241-CX-70, 241-CX-71, and 241-CX-72. Tank 241-CX-70 has been emptied, except for residual quantities of waste, and has been classified as an elementary neutralization tank under the RCRA. Tanks 241-CX-71 and 241-CX-72 contain radioactive and Washington State-only dangerous waste material, but do not present a significant hazard to adjacent facilities, personnel, or the environment. Currently, dangerous waste management activities are not being applied at the tanks. It is unlikely that any incidents presenting hazards to public health or the environment would occur at the Strontium Semiworks Facility

Synthesis of ZnO nanopencils using wet chemical method and its investigation as LPG sensor

International Nuclear Information System (INIS)

Shimpi, Navinchandra G.; Jain, Shilpa; Karmakar, Narayan; Shah, Akshara; Kothari, D.C.; Mishra, Satyendra

2016-01-01

Highlights: • Synthesis using a simple and cost-effective wet chemical process. • Uniform, monodispersed and pure nanoparticles. • Pencil shaped rods with sharp tips. • Understanding of Growth mechanism. • Efficient LPG sensing with high response. • Morphology dependent sensing. - Abstract: ZnO nanopencils (NPCs) were prepared by a novel wet chemical process, using triethanolamine (TEA) as a mild base, which is relatively simple and cost effective method as compared to hydrothermal method. ZnO NPCs were characterized using powder X-ray diffraction (XRD), Fourier Transform Infra-Red (FTIR) spectroscopy in mid-IR and far-IR regions, X-ray Photoelectron Spectroscopy (XPS), UV–vis (UV–vis) absorption spectroscopy, room temperature Photoluminescence (PL) spectroscopy and Field Emission Scanning Electron Microscopy (FESEM). ZnO NPCs obtained, were highly pure, uniform and monodispersed.XRD pattern indicated hexagonal unit cell structure with preferred orientation along the c-axis. Sensing behaviour of ZnO NPCs was studied towards Liquefied Petroleum Gas (LPG) at different operating temperatures. The study shows that ZnO NPCs were most sensitive and promising candidate for detection of LPG at 250 °C with gas sensitivity > 60%. The high response towards LPG is due to high surface area of ZnO NPCs and their parallel alignment.

Synthesis of ZnO nanopencils using wet chemical method and its investigation as LPG sensor

Energy Technology Data Exchange (ETDEWEB)

Shimpi, Navinchandra G., E-mail: navin_shimpi@rediffmail.com [Department of Chemistry, University of Mumbai, Santacruz (East), Mumbai-400098 (India); Jain, Shilpa [Department of Chemistry, University of Mumbai, Santacruz (East), Mumbai-400098 (India); Karmakar, Narayan [Department of Physics, University of Mumbai, Santacruz (East), Mumbai-400098 (India); Shah, Akshara [Department of Chemistry, University of Mumbai, Santacruz (East), Mumbai-400098 (India); Kothari, D.C. [Department of Physics, University of Mumbai, Santacruz (East), Mumbai-400098 (India); National Centre for Nanosciences & Nanotechnology, University of Mumbai, Santacruz (East), Mumbai-400098 (India); Mishra, Satyendra [University Institute of Chemical Technology, North Maharashtra University, Jalgaon (India)

2016-12-30

Highlights: • Synthesis using a simple and cost-effective wet chemical process. • Uniform, monodispersed and pure nanoparticles. • Pencil shaped rods with sharp tips. • Understanding of Growth mechanism. • Efficient LPG sensing with high response. • Morphology dependent sensing. - Abstract: ZnO nanopencils (NPCs) were prepared by a novel wet chemical process, using triethanolamine (TEA) as a mild base, which is relatively simple and cost effective method as compared to hydrothermal method. ZnO NPCs were characterized using powder X-ray diffraction (XRD), Fourier Transform Infra-Red (FTIR) spectroscopy in mid-IR and far-IR regions, X-ray Photoelectron Spectroscopy (XPS), UV–vis (UV–vis) absorption spectroscopy, room temperature Photoluminescence (PL) spectroscopy and Field Emission Scanning Electron Microscopy (FESEM). ZnO NPCs obtained, were highly pure, uniform and monodispersed.XRD pattern indicated hexagonal unit cell structure with preferred orientation along the c-axis. Sensing behaviour of ZnO NPCs was studied towards Liquefied Petroleum Gas (LPG) at different operating temperatures. The study shows that ZnO NPCs were most sensitive and promising candidate for detection of LPG at 250 °C with gas sensitivity > 60%. The high response towards LPG is due to high surface area of ZnO NPCs and their parallel alignment.

ANALYSIS OF OPERATING PARAMETERS AND INDICATORS OF A COMPRESSION IGNITION ENGINE FUELLED WITH LPG

Directory of Open Access Journals (Sweden)

Krzysztof GARBALA

2016-12-01

Full Text Available This article presents the possibilities for using alternative fuels to power vehicles equipped with compression ignition (CI engines (diesel. Systems for using such fuels have been discussed. Detailed analysis and research covered the LPG STAG autogas system, which is used to power dual-fuel engine units (LPG+diesel. A description of the operation of the autogas system and installation in a vehicle has been presented. The basic algorithms of the controller, which is an actuating element of the whole system, have been discussed. Protection systems of a serial production engine unit to guarantee its factorycontrolled durability standards have been presented. A long-distance test drive and examinations of the engine over 150,000 km in a Toyota Hilux have been performed. Operating parameters and performance indicators of the engine with STAG LPG+diesel fuelling have been verified. Directions and perspectives for the further development of such a system in diesel-powered cars have been also indicated.

Radiological health implications of lead-210 and polonium-210 accumulations in LPG refineries

International Nuclear Information System (INIS)

Summerlin, J. Jr.; Prichard, H.M.

1985-01-01

Radon-222, a naturally occurring radioactive noble gas, is often a contaminant in natural gas. During fractionation at processing plants, Radon tends to be concentrated in the Liquified Petroleum Gas (LPG) product stream. Radon-222 decays into a number of radioactive metallic daughters which can plate out on the interior surfaces of plant machinery. The hazards associated with gamma-emitting short-lived radon daughters have been investigated previously. The present work reports an analysis of the hazards associated with the long-lived daughters; Pb-210, Bi-210, and Po-210. These nuclides do not emit appreciable penetrating radiation, and hence do not represent a hazard as long as they remain on the inside surfaces of equipment. However, when equipment that has had prolonged exposure to an LPG stream is disassembled for repair or routine maintenance, opportunities for exposure to radioactive materials can occur. A series of measurements made on an impeller taken from a pump in an LPG facility is reported. Alpha spectroscopy revealed the presence of Po-210, and further measurements showed that the amount on the impeller surface was well above the exempt quantity. Breathing zone measurements made in the course of cleaning the impeller showed that an inhalation exposure equivalent to breathing Po-210 at the Maximum Permissible Concentration (MPC) for 60 hours could be delivered in less than half an hour. It was concluded that maintenance and repair work on LPG and derivitive product stream equipment must be carried out with the realization that a potential radiological health problem exists

Fast-LPG Sensors at Room Temperature by α-Fe2O3/CNT Nanocomposite Thin Films

Directory of Open Access Journals (Sweden)

B. Chaitongrat

2018-01-01

Full Text Available We present performance of a room temperature LPG sensor based on α-Fe2O3/CNT (carbon nanotube nanocomposite films. The nanocomposite film was fabricated via the metallic Fe catalyst particle on CNTs in which both the catalyst particles and the CNT were simultaneously synthesized by chemical vapor deposition (CVD synthesis and were subsequently annealed in air to create α-Fe2O3. These methods are simple, inexpensive, and suitable for large-scale production. The structure, surface morphologies, and LPG response of nanocomposite films were investigated. Raman spectroscopy and XPS analysis showed the formation of α-Fe2O3 on small CNTs (SWNTs. Morphological analysis using FE-SEM and AFM revealed the formation of the porous surface along with roughness surface. Additionally, the sensing performance of α-Fe2O3/CNTs showed that it could detect LPG concentration at lower value than 25% of LEL with response/recovery time of less than 30 seconds at room temperature. These results suggest that the α-Fe2O3/CNTs films are challenging materials for monitoring LPG operating at room temperature.

Law No. 293 of 10 Jun. 1981 about utilization of the Danish underground

Energy Technology Data Exchange (ETDEWEB)

1981-06-10

The law provides the purposeful use and utilization of the Danish underground and its natural resources. The law applies to prospecting, exploration and recovery of resources which had not been economically utilized by private enterprise prior to 23 Febr. 1932. The underground can be utilized as storage place or for other purposes besides recovery. Recovery and research apply as well to the continental Danish shelf. Detailed rules to follow in underground exploration and utilization are precised.

Cryograb: A Novel Approach to the Retrieval of Waste from Underground Storage Tanks - 13501

Energy Technology Data Exchange (ETDEWEB)

O' Brien, Luke; Baker, Stephen; Bowen, Bob [UK National Nuclear Laboratory, Chadwick House, Warrington (United Kingdom); Mallick, Pramod; Smith, Gary [US Department of Energy (United States); King, Bill [Savannah River National Laboratory (United States); Judd, Laurie [NuVision Engineering (United States)

2013-07-01

The UK's National Nuclear Laboratory (NNL) is investigating the use of cryogenic technology for the recovery of nuclear waste. Cryograb, freezing the waste on a 'cryo-head' and then retrieves it as a single mass which can then be treated or stabilized as necessary. The technology has a number of benefits over other retrieval approaches in that it minimizes sludge disturbance thereby reducing effluent arising and it can be used to de-water, and thereby reduce the volume of waste. The technology has been successfully deployed for a variety of nuclear and non-nuclear waste recovery operations. The application of Cryograb for the recovery of waste from US underground storage tanks is being explored through a US DOE International Technology Transfer and Demonstration programme. A sample deployment being considered involves the recovery of residual mounds of sludge material from waste storage tanks at Savannah River. Operational constraints and success criteria were agreed prior to the completion of a process down selection exercise which specified the preferred configuration of the cryo-head and supporting plant. Subsequent process modeling identified retrieval rates and temperature gradients through the waste and tank infrastructure. The work, which has been delivered in partnership with US DOE, SRNL, NuVision Engineering and Frigeo AB has demonstrated the technical feasibility of the approach (to TRL 2) and has resulted in the allocation of additional funding from DOE to take the programme to bench and cold pilot-scale trials. (authors)

Electrophoretic Deposition of SnO2 Nanoparticles and Its LPG Sensing Characteristics

Directory of Open Access Journals (Sweden)

Göktuğ Günkaya

2015-01-01

Full Text Available Homogenized SnO2 nanoparticles (60 nm in acetylacetone mediums, both with and without iodine, were deposited onto platinum coated alumina substrate and interdigital electrodes using the electrophoretic deposition (EPD method for gas sensor applications. Homogeneous and porous film layers were processed and analyzed at various coating times and voltages. The structure of the deposited films was characterized by a scanning electron microscopy (SEM. The gas sensing properties of the SnO2 films were investigated using liquid petroleum gas (LPG for various lower explosive limits (LEL. The results showed that porous, crack-free, and homogeneous SnO2 films were achieved for 5 and 15 sec at 100 and 150 V EPD parameters using an iodine-free acetylacetone based SnO2 suspension. The optimum sintering for the deposited SnO2 nanoparticles was observed at 500°C for 5 min. The results showed that the sensitivity of the films was increased with the operating temperature. The coated films with EPD demonstrated a better sensitivity for the 20 LEL LPG concentrations at a 450°C operating temperature. The maximum sensitivity of the SnO2 sensors at 450°C to 20 LEL LPG was 30.

LNG and LPG total involvement of Pullman Kellogg

Energy Technology Data Exchange (ETDEWEB)

1978-10-01

A discussion of Pullman Kellogg activity covers a new LNG terminal in Belgium; construction of LNG 2 for Sonatrach in Algeria; an LPG recovery system in Kuwait; the Trunkline Gas Co. LNG project at Lake Charles, La.; and the Cove Point, Md., facility for Columbia Gas System Inc. and Consolidated Natural Gas Co., which will be capable of mooring two 750,000 bbl LNG tankers simultaneously.

GIS Analysis of Available Data to Identify regions in the U.S. Where Shallow Ground Water Supplies are Particularly Vulnerable to Contamination by Releases to Biofuels from Underground Storage Tanks

Science.gov (United States)

GIS analysis of available data to identify regions in the U.S. where shallow ground water supplies are particularly vulnerable to contamination by releases of biofuels from underground storage tanks. In this slide presentation, GIS was used to perform a simple numerical and ...

Research of the multibarrier system for an underground deposition of radioactive wastes

Directory of Open Access Journals (Sweden)

Marian Šofranko

2007-01-01

Full Text Available The paper deals in brief with research problems of multiple protection barrier systems for an underground storage of highly radioactive waste in connection with the problem of resolving a definite liquidation of this waste. This problem has a worlwide importance and is comprehensively investigated, evaluated and resolved in many well accepted research centers. Present the experts agree, that the most suitable way of the long-lived radioactive wastes liquidation is their storage into suitable underground geological formations. The core insulation of radioactive wastes from the biosphere for an extremly long time can be achieved by using a technical isolation barrier in combination with an appropriate rock mass.

Dynamic response of underground openings in discontinuous rock

International Nuclear Information System (INIS)

Asmis, H.W.

1984-02-01

This report examines the behaviour of underground openings in discontinuous rock in response to seismic waves associated with either earthquakes or rock bursts. A literature search revealed that well-constructed underground structures, such as would be expected for nuclear fuel waste disposal vaults, underground pumped-storage or nuclear plants, have an extremely high resistance to damage from seismic motion. To complement these qualitative results, it was necessary to examine the basic mechanisms of the entire progression of seismic motion, from wave generation and propagation, to wave interaction with the underground opening. From these investigations, it was found that unless a seismic event occurs very close to the installation, the stresses generated will be low with respect to the excavation stresses, because high stress waves are rapidly attenuated in travelling through rock. As well, an earthquake may generate extremely high accelerations, but is limited in the maximum amount of stress that it can create. The question, however, of the actual specific nature of underground seismic motions still remains essentially unanswered, although it is expected that there is a reduction in peak motions with depth due to the effect of the free surface of the earth

An assessment of the market for LPG and CNG in Peru's transport sector

International Nuclear Information System (INIS)

Boykiw, A. L.

1999-01-01

This is an abridged version of the report prepared by Boykiw and Company Limited to provide a technical, statistical and financial assessment of potential sales of liquefied petroleum gases (LPG) or propane, and compressed natural gas (CNG) to the transportation sector in Peru. Results show that use of CNG and LPG in Peru's transportation sector will primarily be a function of the counrty's vehicle population, the economics of conversion and the availability of infrastructure. With regard to conversion, the fact that 62 per cent of the nation's one million vehicles are located in Lima, combined with their age, the prospects appear to be very favourable. Changing to LPG will also benefit the environment since carbon monoxide and nitrogen oxides emissions will be significantly reduced. Similar environmental benefits are expected from the use of CNG. Assuming that low cost first generation conversion kits can be made available, in combination with the growing refueling infrastructure ( from one in 1994 to 9 by the end of 1999, and an additional five in 2000) should result in a dramatic increase in the number of vehicles using LPG. By contrast, the prospect for CNG as vehicle fuel is less favourable because of the much more complex and costly refuelling station required to make it practicable. Based on very incomplete information on the Lima fleet of vehicles and their operating characteristics, the total number of CNG-fuelled vehicles five years after CNG becomes available in Lima, is estimated at between 2,000 and 3,000, and CNG requirements of between 800,000 and 1,500,000 cubic feet per day

Prediction of electricity and lpg consumption in a hotel using artificial neural networks

International Nuclear Information System (INIS)

Montero, L Reiners; Perez T, Carlos; Gongora L, Ever; Marrero, R Secundino

2009-01-01

This work was developed in order to improve the current tools for energy planning. This makes possible to predict electricity and LPG consumption in a tourist facility with accuracy higher than 90% by using Artificial Neuronal Networks (ANN) as fitting and predictive models. Local climatology and occupational patterns were used as entering variables for the models. Parametric modeling was performed as starting conditions and then improved with ANN. Matlab tools were used for calculations. The average deviation when predicting electricity consumption was 0.6% with a standard deviation of 4%. For LPG consumption the average deviation was less than 1% with a standard deviation of 1.3%.

Synthesis, characterization and liquefied petroleum gas (LPG) sensing properties of WO3 nano-particles

Science.gov (United States)

Singh, Subhash; Majumder, S. B.

2018-05-01

Metal oxide sensors, such as ZnO, SnO2, and WO3 etc. have been utilized for several decades for low-costd etection of combustible and toxic gases. In the present work tungsten oxide (WO3) nanoparticles have been prepared by using an economic wet chemical synthesis route. To understand the phase formation behavior of the synthesized powders, X-ray diffraction analysis has been performed. The microstructure evolution of the synthesized powders was characterized by field-emission scanning electron microscopy (FESEM), and transmission electron microscopy (TEM). The calcined phase pure WO3 nanoparticles are investigated in terms of LPG gas sensing properties. The gas sensing measurements has been done in two different mode of operation (namely static and dynamic measurements). The degree of oxygen deficiency in the WO3 sensor also affected the sensor properties and the optimum oxygen content of WO3 was necessary to get high sensitivity for LPG. The WO3 sensor shows the excellent sensor properties for LPG at the operating temperature of 250°C.

Deep reversible storage. Design options for the storage in deep geological formation - High-medium activity, long living wastes 2009 milestone

International Nuclear Information System (INIS)

2010-09-01

This report aims at presenting a synthesis of currently studied solutions for the different components of the project of deep geological radioactive waste storage centre. For each of these elements, the report indicates the main operational objectives to be taken into account in relationship with safety functions or with reversibility. It identifies the currently proposed design options, presents the technical solutions (with sometime several possibilities), indicates industrial references (in the nuclear sector, in underground works) and comments results of technological tests performed by the ANDRA. After a description of functionalities and of the overall organisation of storage components, the different following elements and aspects are addressed: surface installations, underground architecture, parcel transfer between the surface and storage cells, storage container for medium-activity long-life (MAVL) waste, storage cell for medium-activity long-life waste, handling of MAVL parcels in storage cells, storage container for high-activity (HA) waste, storage cell for HA waste, handling of HA parcels in storage cells, and works for site closing

Review of sensors for the in situ chemical characterization of the Hanford underground storage tanks

International Nuclear Information System (INIS)

Kyle, K.R.; Mayes, E.L.

1994-01-01

Lawrence Livermore National Laboratory (LLNL), in the Technical Task Plan (TTP) SF-2112-03 subtask 2, is responsible for the conceptual design of a Raman probe for inclusion in the in-tank cone penetrometer. As part of this task, LLNL is assigned the further responsibility of generating a report describing a review of sensor technologies other than Raman that can be incorporated in the in-tank cone penetrometer for the chemical analysis of the tank environment. These sensors would complement the capabilities of the Raman probe, and would give information on gaseous, liquid, and solid state species that are insensitive to Raman interrogation. This work is part of a joint effort involving several DOE laboratories for the design and development of in-tank cone penetrometer deployable systems for direct UST waste characterization at Westinghouse Hanford Company (WHC) under the auspices of the U.S. Department of Energy (DOE) Underground Storage Tank Integrated Demonstration (UST-ID)

(Per)chlorate reduction by an acetogenic bacterium, Sporomusa sp., isolated from an underground gas storage.

KAUST Repository

Balk, Melike

2010-08-03

A mesophilic bacterium, strain An4, was isolated from an underground gas storage reservoir with methanol as substrate and perchlorate as electron acceptor. Cells were Gram-negative, spore-forming, straight to curved rods, 0.5-0.8 microm in diameter, and 2-8 microm in length, growing as single cells or in pairs. The cells grew optimally at 37 degrees C, and the pH optimum was around 7. Strain An4 converted various alcohols, organic acids, fructose, acetoin, and H(2)/CO(2) to acetate, usually as the only product. Succinate was decarboxylated to propionate. The isolate was able to respire with (per)chlorate, nitrate, and CO(2). The G+C content of the DNA was 42.6 mol%. Based on the 16S rRNA gene sequence analysis, strain An4 was most closely related to Sporomusa ovata (98% similarity). The bacterium reduced perchlorate and chlorate completely to chloride. Key enzymes, perchlorate reductase and chlorite dismutase, were detected in cell-free extracts.

(Per)chlorate reduction by an acetogenic bacterium, Sporomusa sp., isolated from an underground gas storage.

KAUST Repository

Balk, Melike; Mehboob, Farrakh; van Gelder, Antonie H; Rijpstra, W Irene C; Damsté , Jaap S Sinninghe; Stams, Alfons J M

2010-01-01

A mesophilic bacterium, strain An4, was isolated from an underground gas storage reservoir with methanol as substrate and perchlorate as electron acceptor. Cells were Gram-negative, spore-forming, straight to curved rods, 0.5-0.8 microm in diameter, and 2-8 microm in length, growing as single cells or in pairs. The cells grew optimally at 37 degrees C, and the pH optimum was around 7. Strain An4 converted various alcohols, organic acids, fructose, acetoin, and H(2)/CO(2) to acetate, usually as the only product. Succinate was decarboxylated to propionate. The isolate was able to respire with (per)chlorate, nitrate, and CO(2). The G+C content of the DNA was 42.6 mol%. Based on the 16S rRNA gene sequence analysis, strain An4 was most closely related to Sporomusa ovata (98% similarity). The bacterium reduced perchlorate and chlorate completely to chloride. Key enzymes, perchlorate reductase and chlorite dismutase, were detected in cell-free extracts.

Review of sensors for the in situ chemical characterization of the Hanford underground storage tanks

Energy Technology Data Exchange (ETDEWEB)

Kyle, K.R.; Mayes, E.L.

1994-07-29

Lawrence Livermore National Laboratory (LLNL), in the Technical Task Plan (TTP) SF-2112-03 subtask 2, is responsible for the conceptual design of a Raman probe for inclusion in the in-tank cone penetrometer. As part of this task, LLNL is assigned the further responsibility of generating a report describing a review of sensor technologies other than Raman that can be incorporated in the in-tank cone penetrometer for the chemical analysis of the tank environment. These sensors would complement the capabilities of the Raman probe, and would give information on gaseous, liquid, and solid state species that are insensitive to Raman interrogation. This work is part of a joint effort involving several DOE laboratories for the design and development of in-tank cone penetrometer deployable systems for direct UST waste characterization at Westinghouse Hanford Company (WHC) under the auspices of the U.S. Department of Energy (DOE) Underground Storage Tank Integrated Demonstration (UST-ID).

Performance evaluation of reverse logistics: A case of LPG agency

Directory of Open Access Journals (Sweden)

Kottala Sri Yogi

2015-12-01

Full Text Available Majority of the manufacturing companies are incorporating the practice of reverse logistics in their value chain. In manufacturing processes, the concept of reverse logistics plays a vital role in enhancing the company’s profit margin for sustainable business growth. For every company, there is a need of performance measurement system to be established as successful business tool. However to predict better results, how smartly the inputs for the transformation or business process are being effectively and efficiently used has to be analyzed. Drawing attention to the growing popularity in adapting the best practices of reverse logistics among different manufacturing industries, this paper aims to build a methodology in order to measure the performance of liquefied petroleum gas (LPG agencies. To do so, it has undertaken the Asian emerging market-India as a case study and improved the understanding of performance measurement in reverse logistics to refilling LPG cylinders. Further, it has suggested a framework affecting the implementation of reverse logistics activities and its network.

Component-wise exergy and energy analysis of vapor compression refrigeration system using mixture of R134a and LPG as refrigerant

Science.gov (United States)

Gill, Jatinder; Singh, Jagdev

2017-11-01

In this work, the experimental examination was carried out using a mixture of R134a and LPG refrigerant (consisting of R134a and LPG in a proportion of 28:72 by weight) as a replacement for R134a in a vapor compression refrigeration system. Exergy and energy tests were carried out at different evaporator and condenser temperatures with controlled environmental conditions. The results showed that the exergy destruction in the compressor, condenser, evaporator, and a capillary tube of the R134a / LPG refrigeration system was found lower by approximately 11.13-3.41%, 2.24-3.43%, 12.02-13.47% and 1.54-5.61% respectively. The compressor exhibits the highest level of destruction, accompanied by a condenser, an evaporator and a capillary tube in refrigeration systems. The refrigeration capacity, COP and power consumption of the compressor of the R134a /LPG refrigeration system were detected higher and lower compared to the R134a refrigeration system by about 7.04-11.41%, 15.1-17.82%, and 3.83-8.08% respectively. Also, the miscibility of R134a and LPG blend with mineral oil discovered good. The R134a and LPG refrigerant mixture proposed in this study perform superior to R134a from component-wise exergy and energy analyses under similar experimental conditions.

Component-wise exergy and energy analysis of vapor compression refrigeration system using mixture of R134a and LPG as refrigerant

Science.gov (United States)

Gill, Jatinder; Singh, Jagdev

2018-05-01

In this work, the experimental examination was carried out using a mixture of R134a and LPG refrigerant (consisting of R134a and LPG in a proportion of 28:72 by weight) as a replacement for R134a in a vapor compression refrigeration system. Exergy and energy tests were carried out at different evaporator and condenser temperatures with controlled environmental conditions. The results showed that the exergy destruction in the compressor, condenser, evaporator, and a capillary tube of the R134a / LPG refrigeration system was found lower by approximately 11.13-3.41%, 2.24-3.43%, 12.02-13.47% and 1.54-5.61% respectively. The compressor exhibits the highest level of destruction, accompanied by a condenser, an evaporator and a capillary tube in refrigeration systems. The refrigeration capacity, COP and power consumption of the compressor of the R134a /LPG refrigeration system were detected higher and lower compared to the R134a refrigeration system by about 7.04-11.41%, 15.1-17.82%, and 3.83-8.08% respectively. Also, the miscibility of R134a and LPG blend with mineral oil discovered good. The R134a and LPG refrigerant mixture proposed in this study perform superior to R134a from component-wise exergy and energy analyses under similar experimental conditions.

Energy and exergy analysis of LPG (liquefied petroleum gas) as a drop in replacement for R134a in domestic refrigerators

International Nuclear Information System (INIS)

El-Morsi, Mohamed

2015-01-01

This study presents a comparison of energetic and exergetic performance of a vapour compression refrigeration system using pure HC (hydrocarbon) refrigerants. In this study, three different pure HCs propane (R290), butane (R600) and commercial LPG (liquefied petroleum gas) are used in the theoretical analysis. R134a is also used in the analysis as a reference refrigerant. The evaporator temperature ranges from −30 to 0 °C while the condenser ranges from 30 to 50 °C. MATLAB software is used for solving the thermodynamic equations, while the thermo-physical properties are calculated using REFPROP software. The results show that R600 has the highest COP c and exergetic efficiency, while LPG has the lowest. When compared to R134a, the COP c for R134a is higher than that for LPG by 10%. Also, the exergetic efficiency is higher by 5%. However, LPG has the advantage of being not expensive, available in large amounts and zero ozone depletion potential and low global warming potential. - Highlights: • The results show that R600 has the highest COP c & exergy efficiency, and the lowest irreversibility. • LPG has the lowest COP c & exergy efficiency, and the highest irreversibility. • Compared to R134a, LPG has a lower COP c and exergy efficiency by an average of 10% and 5%, respectively

FY 2000 report on the results of the advanced R and D for the UTES (underground thermal energy storage) system; 2000 nendo chichu jiban chikunetsu system gijutsu sendo kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In this study, study was made of the commercialization of the UTES (underground thermal energy storage) system using the underground heat source heat pump system technology as the base, considering that this is a technology suitable for the urban area where the heat demand intensively increases and a lot of exhaust heat and usable heat exist. By the realization of the UTES system technology, it is expected that the system promotes Japan's utilization of the unused energy and contributes to the construction of the CO2 emission control type society for Japan's energy policy and global warming prevention and secondarily to leveling of power loads and elimination of the heat island phenomenon in large cities. As to the UTES system which is aimed at being used for space heating and cooling and hot water supply in buildings, the following two were studied: the indirect system, BTES (borehole thermal energy storage) system, in which heat is collected/radiated from the ground by the heat exchanger installed underground; the direct system, ATES (aquifer thermal energy storage) system, in which the groundwater stored in aquifer is directly pumped up and used. The study was made in the items written below: 1) establishment of an system image of the UTES system; 2) evaluation study of effects of the introduction, practical applicability, etc. 3) extraction of the subjects for development. As a result, system images of the indirect/direct systems were obtained. (NEDO)

FY 2000 report on the results of the advanced R and D for the UTES (underground thermal energy storage) system; 2000 nendo chichu jiban chikunetsu system gijutsu sendo kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In this study, study was made of the commercialization of the UTES (underground thermal energy storage) system using the underground heat source heat pump system technology as the base, considering that this is a technology suitable for the urban area where the heat demand intensively increases and a lot of exhaust heat and usable heat exist. By the realization of the UTES system technology, it is expected that the system promotes Japan's utilization of the unused energy and contributes to the construction of the CO2 emission control type society for Japan's energy policy and global warming prevention and secondarily to leveling of power loads and elimination of the heat island phenomenon in large cities. As to the UTES system which is aimed at being used for space heating and cooling and hot water supply in buildings, the following two were studied: the indirect system, BTES (borehole thermal energy storage) system, in which heat is collected/radiated from the ground by the heat exchanger installed underground; the direct system, ATES (aquifer thermal energy storage) system, in which the groundwater stored in aquifer is directly pumped up and used. The study was made in the items written below: 1) establishment of an system image of the UTES system; 2) evaluation study of effects of the introduction, practical applicability, etc. 3) extraction of the subjects for development. As a result, system images of the indirect/direct systems were obtained. (NEDO)

Mission of mediation on planting underground research laboratories

International Nuclear Information System (INIS)

Bataille, C.

1994-01-01

France, who chose to have a strong nuclear industry, is confronted to the problem of management, treatment, storage and elimination of radioactive waste. The law defined an important research program with a study of underground storage in laboratories. Here is the report of this mission. A problem of people confidence arose; there is a difference between the great level of science or technology and the level of understanding of public opinion. The only answer brought by a democratic society is to develop information

Clean energy systems in the subsurface. Production, storage and conversion. Proceedings

Energy Technology Data Exchange (ETDEWEB)

Hou, Zhengmeng Michael; Were, Patrick (eds.) [Clausthal Univ. of Technology, Goslar (Germany). Energie-Forschungszentrum Niedersachsen (EFZN); Xie, Heping [Sichuan Univ., Chengdu (China)

2013-04-01

Recent research on Integrated Energy and Environmental Utilization of Deep Underground Space. Results of the 3{sup rd} Sino-German Conference ''Underground Storage of CO{sub 2} and Energy'', held at Goslar, Germany, 21-23 May 2013. Researchers and professionals from academia and industry discuss the future of deep underground space technologies for an integrated energy and environmental utilization. Anthropogenic greenhouse gas emissions, energy security and sustainability are three of the greatest contemporary global challenges today. This year the Sino-German Cooperation Group ''Underground Storage of CO{sub 2} and Energy'', is meeting on the 21-23 May 2013 for the second time in Goslar, Germany, to convene its 3{sup rd} Sino-German conference on the theme ''Clean Energy Systems in the Subsurface: Production, Storage and Conversion''.

An Approach for Developing Site-Specific Lateral and Vertical Inclusion Zones within which Structures Should be Evaluated for Petroleum Vapor Intrusion due to Releases of Motor Fuel from Underground Storage Tanks

Science.gov (United States)

Buildings may be at risk from Petroleum Vapor Intrusion (PVI) when they overlie petroleum hydrocarbon contamination in the unsaturated zone or dissolved in groundwater. The U.S. EPA Office of Underground Storage Tanks (OUST) is preparing Guidance for Addressing Petroleum Vapor I...

Heat transport and storage

International Nuclear Information System (INIS)

Despois, J.

1977-01-01

Recalling the close connections existing between heat transport and storage, some general considerations on the problem of heat distribution and transport are presented 'in order to set out the problem' of storage in concrete form. This problem is considered in its overall plane, then studied under the angle of the different technical choices it involves. The two alternatives currently in consideration are described i.e.: storage in a mined cavity and underground storage as captive sheet [fr

Petroleum products. LPG-c is taking off; Produits petroliers. Le decollage du GPL-c

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

A strong tax reduction and other financial incentives for liquefied petroleum gas, have stimulated LPG consumption in France, with a 60 pc increase between 1995 and 1996. LPG fuels allow for an important reduction in polluting emissions. Other news are presented, which concern the French Petroleum Institute strategy and financing, European regulations on fuel quality, the issue of the decreasing number of service stations in France, new production sites for bio-fuels, issues with petroleum investment international embargoes, the privatization of Elf-Aquitaine, the 1996 truck driver strike, and the Goa international conference between energy producer and user countries

Petroleum products. LPG-c is taking off; Produits petroliers. Le decollage du GPL-c

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-31

A strong tax reduction and other financial incentives for liquefied petroleum gas, have stimulated LPG consumption in France, with a 60 pc increase between 1995 and 1996. LPG fuels allow for an important reduction in polluting emissions. Other news are presented, which concern the French Petroleum Institute strategy and financing, European regulations on fuel quality, the issue of the decreasing number of service stations in France, new production sites for bio-fuels, issues with petroleum investment international embargoes, the privatization of Elf-Aquitaine, the 1996 truck driver strike, and the Goa international conference between energy producer and user countries

Novel, low-vibration excavation techniques for underground radioactive waste storage

International Nuclear Information System (INIS)

Kogelmann, W.J.

1994-01-01

In order to meet the construction specifications of the challenging Yucca Mountain nuclear waste repository, novel, low-vibration tunneling and shaft sinking techniques must be applied. Conventional roadheaders, even with reduced cutting speed, cannot be employed due to the high strength and widely varying physical properties of the rock formations. The Multi Tool Miner (MTM) concept utilizes both an impact hammer, for efficient hard rock mining, and a cutter head, tooled with drag-bits (picks), to profile tunnel walls down to the sound, undisturbed rock, in order to meet the 10,000-year stability requirement for underground structures. As the operational requirements and rock conditions at the Yucca Mountain site are not suitable for wide, transverse open-quotes ripperclose quotes cutting drums, a small diameter, in-line, open-quotes milling augerclose quotes cutter head was developed. The synergetic combination of high-production hammer excavation and precise milling will facilitate the construction of stable, long-life underground structures within the budget limitations mandated by Congress

Predicting the performances of a CAMPRO engine retrofitted with liquefied petroleum gas (LPG system using 1-dimensional software

Directory of Open Access Journals (Sweden)

Kamaruddin M. Hazeem

2017-01-01

Full Text Available Recently, the depletion of petroleum resources and the impact of exhaust emission caused by combustion towards environmental has been forced to all researchers to come out with an alternative ways to prevent this situation become worse. Liquefied petroleum gas (LPG is the most compatible and have a potential to become a source of energy for internal combustion engine. Unfortunately, the investigation of LPG in internal combustion engine among researcher still have a gap in research. Thus, in this study a 1-Dimensional simulation CAMPRO 1.6L engine model using GT-Power is developed to predict the performances of engines that using LPG as a fuel for internal combustion engine. The constructed model simulation will throughout the validation process with the experimental data to make sure the precision of this model. The validation process shows that the results have a good agreement between the simulation model and the experimental data. As a result, the performance of LPG simulation model shows that a Brake Torque (BT, Brake Power (BP and Brake Mean Effective Pressure (BMEP were significantly improved in average of 7% in comparison with gasoline model. In addition, Brake Specific Fuel Consumption (BSFC also shows an improvement by 5%, which is become more economic. Therefore, the developed GT-Power model offer a successful fuel conversion to LPG systems via retrofit technology to provide comprehensive support for implementation of energy efficient and environmental friendly vehicles.

Report of working committee 1 ''exploration, production, treatment and underground storage of natural gas''; Rapport du comite de travail 1 ''exploration, production, traitement et stockage souterrain du gaz naturel

Energy Technology Data Exchange (ETDEWEB)

Rekdal, Ottar

2000-07-01

This report describes the activities of Working Committee 1 during the triennium 1997 - 2000. The first part of the report gives an overview of the current situation world-wide within the basic activities of the committee, i.e. exploration, production, treatment and underground storage of natural gas. In the second part of the report analyses of three prioritized topics important to the industry are described: - Improving the performance of existing gas storages; - Use of 3-D seismic data in exploration, production and underground storage. - Development of small-scale offshore gas fields. The report will be presented during the WOC 1 sessions at the World Gas Conference 2000, together with papers selected by the committee. Other relevant papers will be presented during the poster session. Furthermore, the committee will organize a round table session addressing reductions of greenhouse gas emissions along the gas chain. Representatives from industry, environmental organisations and politicians will take part in this round table discussion. (author)

Solubility studies of Np(V) in simulated underground water

International Nuclear Information System (INIS)

Zhang Yingjie; Ren Lilong; Jiao Haiyang; Yao Jun; Su Xiguang; Fan Xianhua

2004-01-01

The solubility of Np(V) in simulated underground water has been measured with the variation of pH, storage time (0-100 days). All experiments were performed in an Ar glove box which contained high purity Ar, with an oxygen content of less than 5ppm. Experimental results show that the solubility of Np(V) in simulated underground water decreased with increasing pH value of solution; the solubility of Np(V) in simulated underground water determined at different pH is : pH=6.96, [Np(V)]=(3.52±0.37) x 10 -4 mol/L; pH=8.04, [Np(V)]=(8.24±0.32) x 10 -5 mol/L; pH=9.01, [Np(V)]=(3.04±0.48) x 10'- 5 mol/L, respectively. (author)

30 CFR 57.6800 - Storage facilities.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Storage facilities. 57.6800 Section 57.6800...-Surface and Underground § 57.6800 Storage facilities. When repair work which could produce a spark or flame is to be performed on a storage facility— (a) The explosive material shall be moved to another...

Liquefied Petroleum Gases (LPG) and the fight against deforestation: the Senegal example

International Nuclear Information System (INIS)

Boubacar, B.

1993-01-01

Domestic LPG consumption in Senegal is over 40,000 tonnes in 1992, thus preserving more than 33,000 hectares of forest. Three reasons explain the success of the 'butanization' policy implemented by the country in its fight against deforestation: political desire, constant cooperation between the public authorities and distributors, but also a supply of gas and inexpensive cookers. The penetration of these butane cookers on the market occurred mainly in urban areas (it is the leading household appliance of urban families in Senegal), but it is also quite visible in rural areas as well, explained Mr. Boubacar Barry General Manager of Totalgaz Senegal in his speech 'How to fight the Growing Desert with Simple Means and a little imagination' during the 6th World LPG Meeting last October in Marrakech. 2 figs., 3 photos

Nanostructured ZnO films for potential use in LPG gas sensors

Science.gov (United States)

Latyshev, V. M.; Berestok, T. O.; Opanasyuk, A. S.; Kornyushchenko, A. S.; Perekrestov, V. I.

2017-05-01

The aim of the work was to obtain ZnO nanostructures with heightened surface area and to study relationship between formation method and gas sensor properties towards propane-butane mixture (LPG). In order to synthesize ZnO nanostructures chemical and physical formation methods have been utilized. The first one was chemical bath deposition technology and the second one magnetron sputtering of Zn followed by oxidation. Optimal method and technological parameters corresponding to formation of material with the highest sensor response have been determined experimentally. Dynamical gas sensor response at different temperature values and dependencies of the sensor sensitivity on the temperature at different LPG concentrations in air have been investigated. It has been found, that sensor response depends on the sample morphology and has the highest value for the structure consisting of thin nanowires. The factors that lead to the decrease in the gas sensor operating temperature have been determined.

Storage facility for radioactive wastes

International Nuclear Information System (INIS)

Okada, Kyo

1998-01-01

Canisters containing high level radioactive wastes are sealed in overpacks in a receiving building constructed on the ground. A plurality of storage pits are formed in a layered manner vertically in multi-stages in deep underground just beneath the receiving building, for example underground of about 1000m from the ground surface. Each of the storage pits is in communication with a shaft which vertically communicates the receiving building and the storage pits, and is extended plainly in a horizontal direction from the shaft. The storage pit comprises an overpack receiving chamber, a main gallery and a plurality of galleries. A plurality of holes for burying the overpacks are formed on the bottom of the galleries in the longitudinal direction of the galleries. A plurality of overpack-positioning devices which run in the main gallery and the galleries by remote operation are disposed in the main gallery and the galleries. (I.N.)

Conceptual study on deep-underground energy generation base

International Nuclear Information System (INIS)

Hayano, M.; Okawa, T.

1992-01-01

Mitsubishi Atomic Power Industries, Inc. (MAPI) and Taisei Corporation have started a conceptual study on a deep-underground energy generation base for future cities in the 21st century around the metropolitan area, which will be increasingly important from viewpoints of the autonomy and sharing of the energy supply to the future cities. The energy generation base consists of a gas cooled reactor with naturally safety features as the energy source, an electric generation base using the Alkali Metal Thermo-electric Converter (AMTEC), a hydrogen production plant with the Solid Polymer Electrolyte (SPE), a hydrogen storage plant with the Metal Hydride (MH), and a desalination plant. This paper describes a concept of the energy generation base and the structure in the deep-underground, in soft soil, then the basic system of each plant, and finally discusses the feasibility of the deep-underground energy generation base. (author)

Development of a computer code to predict a ventilation requirement for an underground radioactive waste storage tank

Energy Technology Data Exchange (ETDEWEB)

Lee, Y.J.; Dalpiaz, E.L. [ICF Kaiser Hanford Co., Richland, WA (United States)

1997-08-01

Computer code, WTVFE (Waste Tank Ventilation Flow Evaluation), has been developed to evaluate the ventilation requirement for an underground storage tank for radioactive waste. Heat generated by the radioactive waste and mixing pumps in the tank is removed mainly through the ventilation system. The heat removal process by the ventilation system includes the evaporation of water from the waste and the heat transfer by natural convection from the waste surface. Also, a portion of the heat will be removed through the soil and the air circulating through the gap between the primary and secondary tanks. The heat loss caused by evaporation is modeled based on recent evaporation test results by the Westinghouse Hanford Company using a simulated small scale waste tank. Other heat transfer phenomena are evaluated based on well established conduction and convection heat transfer relationships. 10 refs., 3 tabs.

Radioactive wastes: underground laboratories implantation

International Nuclear Information System (INIS)

Bataille, Ch.

1997-01-01

This article studies the situation of radioactive waste management, more especially the possible storage in deep laboratories. In front of the reaction of public opinion relative to the nuclear waste question, it was essential to begin by a study on the notions of liability, transparence and democracy. At the beginning, it was a matter of underground researches with a view to doing an eventual storage of high level radioactive wastes. The Parliament had to define, through the law, a behaviour able to come to the fore for anybody. A behaviour which won recognition from authorities, from scientists, from industrial people, which guarantees the rights of populations confronted to a problem whom they were not informed, on which they received only few explanations. (N.C.)

Underground dams for irrigation supplies in coastal limestone aquifer, Okinawa, Japan

Science.gov (United States)

Yasumoto, J.; Nakano, T.; Nawa, N.

2011-12-01

The use of underground dams to store water in regions with arid or tropical climates is a method that has received considerable attention in the last few decades. And now, for the tropical and subtropical islands that are highly vulnerable to climate change underground dams have been attracting attention again as a method of groundwater management. Okinawa Prefecture is Japan's southernmost prefecture, which consists of hundreds of islands in a chain over 1,000 km long, called the Ryukyu Islands which extend southwest from Kyushu to Taiwan. The national irrigation project of the Ryukyu Islands has been carried out, and several underground dams have been constructed. The Komesu and Giiza underground dams are first full scale underground dam facilities constructed for irrigation in Japan. The Komesu underground dam is a salt-water proof type. It prevents salt-water intrusion and provides storage fresh-water for irrigation in coastal limestone aquifer. Giiza underground dam is a dam up type for storage of fresh-water. These groundwater reservoirs are located in the coastal region of southern part of Okinawa (main island), where Ryukyu limestone is extensively distributed. We studied the behaviour of groundwater flow, saltwater intrusion and nitrate nitrogen (NO3-N) in groundwater in this region by using observation data of groundwater and springs through long term (from 1993 to 2010) monitoring. And, a groundwater flow and salt-water intrusion analysis have been conducted with three dimensional numerical model applied to these dam reservoir areas. The MODFLOW-NWT with SWI code and PEST was used to simulate the complex groundwater flow patterns. Through the comparison with simulation and observed data, it was concluded that the cut off wall of underground dams effectively stores the groundwater and prevents the salt-water intrusion in the reservoir areas. The observed groundwater levels at the reservoir areas were almost reproduced by the numerical model, but there

Fuel switching from wood to LPG can benefit the environment

International Nuclear Information System (INIS)

Nautiyal, Sunil; Kaechele, Harald

2008-01-01

The Himalaya in India is one of the world's biodiversity hotspots. Various scientific studies have reported and proven that many factors are responsible for the tremendous decline of the Himalayan forests. Extraction of wood biomass from the forests for fuel is one of the factors, as rural households rely entirely on this for their domestic energy. Efforts continue for both conservation and development of the Himalayan forests and landscape. It has been reported that people are still looking for more viable solutions that could help them to improve their lifestyle as well as facilitate ecosystem conservation and preservation of existing biodiversity. In this direction, we have documented the potential of the introduction of liquefied petroleum gas (LPG), which is one of the solutions that have been offered to the local people as a substitute for woodfuel to help meet their domestic energy demand. The results of the current study found dramatic change in per capita woodfuel consumption in the last two decades in the villages where people are using LPG. The outcome showed that woodfuel consumption had been about 475 kg per capita per year in the region, but after introduction of LPG, this was reduced to 285 kg per capita per year in 1990-1995, and was further reduced to 46 kg per capita per year in 2000-2005. Besides improving the living conditions of the local people, this transformation has had great environmental consequences. Empirical evidence shows that this new paradigm shift is having positive external effects on the surrounding forests. Consequently, we have observed a high density of tree saplings and seedlings in adjacent forests, which serves as an assessment indicator of forest health. With the help of the current study, we propose that when thinking about a top-down approach to conservation, better solutions, which are often ignored, should be offered to local people

30 CFR 905.817 - Peformance standards-Underground mining activities.

Science.gov (United States)

2010-07-01

... Hazardous Waste Control Law, Cal. Health & Safety Code section 25100 et seq.; the State Underground Storage of Hazardous Substances Law, Cal. Health & Safety Code section 25280 et seq.; the Solid Waste Management and Resource Recovery Act of 1972, Cal. Gov. Code section 66770 et seq.; the California...

New pemex agency, smog checks greet Mexican LPG vehicle users

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that the relaxation of prohibitions on the use of propane as a motor fuel has spurred sizeable business activity in carburetion and higher demand for LPG throughout Mexico and particularly in Mexico City. However, a number of unforeseen problems have developed that required tough, immediate solutions. After the alternative fuels project began at city hall in Mexico City, publicity spread nationwide, reportedly spurring conversion activity in many other cities. That led to additional demand for fuel of a magnitude that few people had anticipated. In order to assume control of the situation, the national oil company, Pemex, established an official LPG Motor Fuel Department on June 1. Operating in conjunction with the Ministry of Industry, the new department has been busy registering every major propane-powered fleet in the country. Most important, the rate of conversion work must now be pegged to the availability of fuel. It is believed that conversion activity has become more evenly paced since the new Pemex agency took over.over

Thermal balance of a LPG fuelled, four stroke SI engine with water addition

International Nuclear Information System (INIS)

Ozcan, Hakan; Soeylemez, M.S.

2006-01-01

The effect of water injection on a spark ignition engine thermal balance and performance has been experimentally investigated. A four stroke, four cylinder conventional engine was used with LPG (liquid petroleum gas) as fuel. Different water to fuel ratios by mass were used with variable engine speed ranging from 1000 to 4500 rpm. The results showed that as the water injection level to the engine increased, the percentage of useful work increased, while the losses other than unaccounted losses decreased. Additionally, the specific fuel consumption decreases, while the engine thermal efficiency increases. The average increase in the brake thermal efficiency for a 0.5 water to fuel mass ratio is approximately 2.7% over the use of LPG alone for the engine speed range studied

Steam reforming as a method to treat Hanford underground storage tank (UST) wastes

International Nuclear Information System (INIS)

Miller, J.E.; Kuehne, P.B.

1995-07-01

This report summarizes a Sandia program that included partnerships with Lawrence Livermore National Laboratory and Synthetica Technologies, Inc. to design and test a steam reforming system for treating Hanford underground storage tank (UST) wastes. The benefits of steam reforming the wastes include the resolution of tank safety issues and improved radionuclide separations. Steam reforming destroys organic materials by first gasifying, then reacting them with high temperature steam. Tests indicate that up to 99% of the organics could be removed from the UST wastes by steam exposure. In addition, it was shown that nitrates in the wastes could be destroyed by steam exposure if they were first distributed as a thin layer on a surface. High purity alumina and nickel alloys were shown to be good candidates for materials to be used in the severe environment associated with steam reforming the highly alkaline, high nitrate content wastes. Work was performed on designing, building, and demonstrating components of a 0.5 gallon per minute (gpm) system suitable for radioactive waste treatment. Scale-up of the unit to 20 gpm was also considered and is feasible. Finally, process demonstrations conducted on non-radioactive waste surrogates were carried out, including a successful demonstration of the technology at the 0.1 gpm scale

Adaptation of magnesian cements to underground storage of nuclear wastes

International Nuclear Information System (INIS)

Dufournet, F.

1987-01-01

The aim of this thesis is the experimental study of magnesium oxychloride cements as filling materials for underground granitic cavities containing high level radioactive wastes. After a bibliographic study, mechanical properties are examined before and after setting, in function of the ratio MgO/MgCl 2 . Then behavior with water is investigated: swelling, cracking and leaching [fr

CONVERSION OF DIESEL ENGINE INTO SPARK IGNITION ENGINE TO WORK WITH CNG AND LPG FUELS FOR MEETING NEW EMISSION NORMS

Directory of Open Access Journals (Sweden)

Syed Kaleemuddin

2010-01-01

Full Text Available Fluctuating fuel prices and associated pollution problems of largely exploited petroleum liquid fuel has stimulated the research on abundantly available gaseous fuels to keep the mobility industry intact. In the present work an air cooled diesel engine was modified suitably into a spark ignition engine incorporating electronic ignition and variable speed dependant spark timing to accommodate both LPG and CNG as fuels. Engine was optimized for stoichiometric operation on engine dynamometer. Materials of a few intricate engine components were replaced to suit LPG and CNG application. Ignition timing was mapped to work with gaseous fuels for different speeds. Compensation was done for recovering volumetric efficiency when operated with CNG by introducing more volume of air through resonator. Ignition timing was observed to be the pertinent parameter in achieving good performance with gaseous fuels under consideration. Performance and emission tests were carried out on engine dynamometer and chassis dynamometer. Under wide open throttle and at rated speed condition, it was observed that the peak pressure with LPG was lying between diesel fuel and CNG fuel operation due to slow burning nature of gaseous fuels. As compression ratio was maintained same for LPG and CNG fuel operation, low CO emissions were observed with LPG where as HC + NOx emissions were lower with CNG fuel operation. Chassis dynamometer based emission tests yielded lower CO2 levels with CNG operation.

Subaquatic, pressure vessels and LPG storage spheres internal inspection; Inspecao interna de esfera utilizando mergulho como acesso

Energy Technology Data Exchange (ETDEWEB)

Filgueira Filho, Rafael; Monteiro, Ayres [PETROBRAS, Rio de Janeiro, RJ (Brazil)

2005-07-01

Minimizing shut-down costs is a widespread target in the oil and gas industry. The use of new inspection techniques is one of the ways for that. This work presents a new procedure for internal inspections in pressure vessels by the non destructive testing - NDT, ACFM, using industrial diving techniques. As a pioneer experience, this method was applied in the inspection of the internal parts of the LPG sphere tank 5101 at PETROBRAS Transporte S.A. - TRANSPETRO, in Jequie's Terminal, in the state of Bahia, in december, 2003. This new method allows the reduction of indirect costs related to operational unavailability of the equipment, by the reduction of the shut-down time in approximately 50%, when compared to the demanded shut down time, when using scaffolds for accessing the internal parts. Despite of direct costs are still higher with the new methodology, this paper demonstrates the economical feasibility of this new method, based on the savings obtained with the fastest return of the equipment to operation. (author)

Structural analysis of ORNL underground gunite waste storage tanks

International Nuclear Information System (INIS)

Fricke, K.E.

1995-01-01

The North Tank Farm (NTF) and the South Tank Farm (STF) located at ORNL contains 8 underground waste storage tanks which were built around 1943. The tanks were used to collect and store the liquid portion of the radioactive and/or hazardous chemical wastes produced as part of normal facility operations at ORNL, but are no longer part of the active Low Level Liquid Waste system of the Laboratory. The tanks were constructed of gunite. The six STF tanks are 50 ft in diameter, and have a 12 ft sidewall, and an arched dome rising another 6.25 ft. The sidewall are 6 in. thick and have an additional 1.5 in. gunite liner on the inside. There is a thickened ring at the wall-dome juncture. The dome consists of two 5 in. layers of gunite. The two tanks in the NTF are similar, but smaller, having a 25 ft diameter, no inner liner, and a dome thickness of 3.5 in. Both sets of tanks have welded wire mesh and vertical rebars in the walls, welded wire mesh in the domes, and horizontal reinforcing hoop bars pre-tensioned to 35 to 40 ksi stress in the walls and thickened ring. The eight tanks are entirely buried under a 6 ft layer of soil cover. The present condition of the tanks is not accurately known, since access to them is extremely limited. In order to evaluate the structural capability of the tanks, a finite element analysis of each size tank was performed. Both static and seismic loads were considered. Three sludge levels, empty, half-full, and full were evaluated. In the STF analysis, the effects of wall deterioration and group spacing were evaluated. These analyses found that the weakest element in the tanks is the steel resisting the circumferential (or hoop) forces in the dome ring, a fact verified separately by an independent reviewer. However, the hoop steel has an adequate demand/capacity ratio. Buckling of the dome and the tank walls is not a concern

Liquefied natural gas storage at Ambergate

Energy Technology Data Exchange (ETDEWEB)

Higton, C W; Mills, M J

1970-08-19

Ambergate works was planned in 1965-1966 and the decision was taken to install 4 ICI lean gas reformers using natural gas as feedstock, fuel, and enrichment. To cover the possible failure of natural gas supplies, petroleum distillate would be used as alternative feedstock and fuel. The choice for alternative enrichment lay between LPG or LNG. Since LNG would provide peak-on-peak storage facilities for either the East Midlands Board or the Gas Council when conversion was completed--and in the meantime would provide an additional source of LNG for local requirements when temporary LNG installations were used during conversion--agreement was reached with the Gas Council for it to build a 5,000-ton storage installation at Ambergate. The installation consists of 3 major sections: (1) the offloading bay and storage tank; (2) the reliquefaction system; and (3) the export system. The offloading bay and storage tank are for the reception and storage of liquefied Algerian natural gas, delivered to Ambergate by road tanker from the Canvey Is. Terminal. The reliquefaction system is to maintain the necessary storage tank conditions by reliquefying the boil-off natural gas. The export system delivers LNG from the storage tank at high pressure through a vaporization section in the national methane grid.

Operation and management of United Central Piping LPG supply stations in Shenzhen

Energy Technology Data Exchange (ETDEWEB)

Lai Yankai

1997-11-01

Shenzhen has based its city gas development project on the eventual conversion to natural gas supply by way of central piping LPG supply stations. To fully exploit the potential gas supply capability of every central piping station and cut down the total running cost, we have been connecting the existing supply stations and their piping system into a network, which not only provided a more reliable gas supply performance, but can greatly simplify the evacuation of gas stations from the ever-expanding downtown areas to suburbs. Through this way, the periodic gas stock held by individual stations can be transferred to storage terminal or stations of enough holding capability; the supplying distance has been much lengthened and the gas volume held in the piping system increased; gas supply covered by small stations has been shifted to new and large stations. By linking these stations, we are able to provide pipeline LP gas supply for a large area, and in the same time lay down the pipeline infrastructure for the upcoming LNG supply so that an easy conversion to LNG supply can be secured as soon as the projected LNG terminal is put to service. (au)

LPG and NH3 Sensing Properties of SnO2 Thick Film Resistors Prepared by Screen Printing Technique

Directory of Open Access Journals (Sweden)

A. S. GARDE

2010-11-01

Full Text Available The gas sensing behavior of SnO2 thick film resistors deposited on alumina substrates has been investigated for LPG and NH3 gas. The standard screen printing technology was used to prepare the thick films. The films were fired at optimized temperature of 780 0C for 30 minutes. The material characterization was performed by XRD, SEM, FTIR, UV and EDAX for elemental analysis. IR spectroscopy analysis at 2949.26 cm-1 showed the peak assigned to the –Sn-H vibration due to the effect of hybridization i.e. sp3 and the sharp peak at 3734.31 cm-1 assigned to –Sn-OH stretching vibration due to hydrogen bonding. The variation of D.C electrical resistance of SnO2 film samples was measured in air as well as in LPG and NH3 gas atmosphere as a function of temperature. The SnO2 film samples show negative temperature coefficient of résistance. The SnO2 film samples showed the highest sensitivity to 600 ppm of LPG at 230 0C and NH3 at 370 0C. The effect of microstructure on sensitivity, response time and recovery time of the sensor in the presence of LPG and NH3 gases were studied and discussed.

Room temperature LPG resistive sensor based on the use of a few-layer graphene/SnO2 nanocomposite.

Science.gov (United States)

Goutham, Solleti; Bykkam, Satish; Sadasivuni, Kishor Kumar; Kumar, Devarai Santhosh; Ahmadipour, Mohsen; Ahmad, Zainal Arifin; Rao, Kalagadda Venkateswara

2017-12-20

A nanocomposite consisting of a few layers of graphene (FLG) and tin dioxide (SnO 2 ) was prepared by ultrasound-assisted synthesis. The uniform SnO 2 nanoparticles (NPs) on the FLG were characterized by X-ray diffraction in terms of lattice and phase structure. The functional groups present in the composite were analyzed by FTIR. Electron microscopy (HR-TEM and FE-SEM) was used to study the morphology. The effect of the fraction of FLG present in the nanocomposite was investigated. Sensitivity, selectivity and reproducibility towards resistive sensing of liquid propane gas (LPG) was characterized by the I-V method. The sensor with 1% of FLG on SnO 2 operated at a typical voltage of 1 V performs best in giving a rapid and sensitive response even at 27 °C. This proves that the operating temperature of such sensors can be drastically decreased which is in contrast to conventional metal oxide LPG sensors. Graphical abstract Schematic of a room temperature gas sensor for liquefied petroleum gas (LPG). It is based on the use of a few-layered graphene (1 wt%)/SnO 2 nanocomposite that was deposited on an interdigitated electrode (IDEs). A sensing mechanism for LPG detection has been established.

Management for the LPG downstream business

International Nuclear Information System (INIS)

Christiansen, C.

1997-01-01

Traditionally the LPG business is regarded as a low-tech area. Safety has always been top priority, but the applied technology in production as well as distribution has by and large not changed much in the course of the business' 60-year-history. Only few has realised that changes are the necessary mark of the future for this business. Internal and external requirements to the management demand a much higher level of information. The trend dictates a future demand for documented safety. This documentation will only become available through introduction of the latest technology in the business. A technology that also provides decision-making tools for the management to ensure the continued optimum operation of the business. (au)

Applied research on energy storage and conversion for photovoltaic and wind energy systems. Volume II. Photovoltaic systems with energy storage. Final report

Energy Technology Data Exchange (ETDEWEB)

1978-01-01

This volume of the General Electric study was directed at an evaluation of those energy storage technologies deemed best suited for use in conjunction with a photovoltaic energy conversion system in utility, residential and intermediate applications. Break-even cost goals are developed for several storage technologies in each application. These break-even costs are then compared with cost projections presented in Volume I of this report to show technologies and time frames of potential economic viability. The form of the presentation allows the reader to use more accurate storage system cost data as they become available. The report summarizes the investigations performed and presents the results, conclusions and recommendations pertaining to use of energy storage with photovoltaic energy conversion systems. Candidate storage concepts studied include (1) above ground and underground pumped hydro, (2) underground compressed air, (3) electric batteries, (4) flywheels, and (5) hydrogen production and storage. (WHK)

Electricity storage by gas pumping. An introduction to thermodynamic storage processes

International Nuclear Information System (INIS)

Ruer, Jacques

2013-01-01

To date, Pumped Hydro Storage (PHS) is practically the only technology used to store large quantities of electricity. There are however other ways to achieve the same goal. There are not yet well known, because the interest for large scale storage is quite new A complete family of storage technologies can be defined as 'Thermodynamic Storage Systems'. Their only common factor is that a gas is pumped and expanded in the process. If the gas is air taken from the atmosphere and discharged to it, the system is said 'an open system'. This is already developed in the form of Compressed Air Energy Storage (CAES). Different embodiments are possible, following the way the heat gene - rated during the compression stage is conserved. The compressed air is generally stored in underground caverns created in deep salt formations. 2 installations are presently operating and many projects are envisaged. if the gas circulates in closed loop within the plant, the system is said 'a closed system' In this case, the energy is stored as heat and/or cold at different temperature levels. A great variety of technologies can be imagined and are under development, using different gases (e.g. argon, CO 2 ) and different temperature ranges. PHS and CAES require specific sites for water reservoirs or underground caverns. The dosed systems can be installed basically anywhere. (author)

Heat storage in underground caverns - measurements and simulations; Speicherung von Waerme in Grubenraeumen - Messung und Simulation

Energy Technology Data Exchange (ETDEWEB)

Schaberg, A; Krause, H; Poetke, W [TU Bergakademie Freiberg (Germany). Inst. fuer Waermetechnik und Technische Thermodynamik

1997-12-01

Among the different discussed underground concepts for longterm storing of solar or waste heat old waterfilled mines can be an interesting solution. To examine the temperature behaviour of this storage type a testing store is built in a mine belonging to the Freiberg University of Mining and Technology in Saxonia. In a longterm project temperatures are measured inside the water volume and in the adjacent rock. The temperature behaviour depends on the operating conditions. Inside the water volume temperature stratification can be observed. During loading and standstill heat is transported into the rock surrounding. A certain part of this amount of heat can be discharged again. For designing and optimizing this storage type a numerical modell is developed. The modell is validated with experimental data from the testing plant. (orig.) [Deutsch] Unter den verschiedenen, in der Diskussion stehenden Untegrund-Waermespeichern fuer Solarwaerme oder Abwaerme bieten sich auch geflutete Gruben als Waermespeicher an. Zur Untersuchung des Temperaturverhaltens dieses Speichertyps ist im Saechsischen Lehr- und Besucherbergwerk der TU Bergakademie Freiberg ein Versuchsspeicher errichtet worden. In einem Langzeitversuch wird das Temperaturfeld im Wasser und im angrenzenden Gestein aufgezeichnet. Das Temperaturverhalten ist von den Betriebsgroessen abhaengig. Im Grubenwasser stellt sich eine stabile Temperaturschichtung ein. Waehrend der Beladung und der Stillstandszeiten wird Waerme in die Gesteinsumgebung transportiert. Ein Teil dieser Waermemenge kann wider entspeichert werden. Zur Auslegung und Optimierung von Gruben-Waermespeichern ist ein numerisches Modell entwickelt worden. Das Modell ist anhand der Messergebnisse des Versuchsspeichers validiert worden. (orig.)

Silos. Optimisation of underground storages' management

International Nuclear Information System (INIS)

Formaggio, M.

1997-01-01

The operation of Silos in the optimization of storages' management at Snam is presented, together with an assessment of the benefits obtained through closer attention and higher commitment of the staff, as well as better communication between Dispatching and other organizational functions. Silos has proven to be a useful decision-making tool, while applying traditional risk-assessment methods. (au)

Current gas storage R and D programmes at Gas Research Institute

International Nuclear Information System (INIS)

Shikari, Y.A.

1990-01-01

The Gas Research Institute (GRI) is currently involved in the development of concepts aimed at an enhancement of natural gas service to the consumer. In order to maintain the attractiveness of the gas options to industrial consumers and to reinforce the ''value-in-use'' of natural gas to residential as well as commercial customers, it is essential to develop efficient, economical, and safe means of reducing the ''cost-of-service'', including that of natural gas storage in underground formations. Specifically, research and development (R and D) is needed to explore ways to better utilize existing storage fields and also to develop new storage facilities at minimum cost. GRI is currently sponsoring research projects aimed at controlling gas migration in underground gas storage reservoirs, reducing base (or cushion) gas requirements, understanding the gas-gas phase mixing behaviour via laboratory experiments and reservoir models, developing cost-effective gas separation processes using membranes, and optimizing the operation and maintenance (O and M) costs of underground gas storage operations. This paper provides an overview of the GRI's Gas Storage R and D Programme and highlights key results achieved to date for selected research projects. (author). 16 refs, 6 figs, 3 tabs

Addendum to the corrective action plan for Underground Storage Tanks 1219-U, 1222-U, 2082-U, 2068-U at the Rust Garage Facility, Buildings 9720-15 and 9754-1: Oak Ridge Y-12 Plant, Oak Ridge, Tennessee, Facility ID number-sign 0-010117

International Nuclear Information System (INIS)

1994-01-01

This document represents an addendum to the Corrective Action Plan (CAP) for underground storage tanks 1219-U, 2082-U, and 2068-U located at Buildings 9720-15 and 9754-1, Oak Ridge Y-12 Plant, Oak Ridge, TN. The site of the four underground storage tanks is commonly referred to as the Rust Garage Facility. The original CAP was submitted to the Tennessee Department of Environment and Conservation (TDEC) for review in May 1992. During the time period after submission of the original CAP for the Rust Garage Facility, Y-12 Plant Underground Storage Tank (UST) Program personnel continued to evaluate improvements that would optimize resources and expedite the activities schedule presented in the original CAP. Based on these determinations, several revisions to the original corrective action process options for remediation of contaminated soils are proposed. The revised approach will involve excavation of the soils from the impacted areas, on-site thermal desorption of soil contaminants, and final disposition of the treated soils by backfilling into the subject site excavations. Based on evaluation of the corrective actions with regard to groundwater, remediation of groundwater under the Y-12 Plant CERCLA Program is proposed for the facility

Co-ordinated management of two underground gas facilities in aquifer

International Nuclear Information System (INIS)

D'Haussy, P.L.

1990-01-01

Coordinated management of two underground natural gas storage facilities which are approximately 10 km apart is described. The essential part of service installations allowing their operation is provided at a single location and is common to both facilities, which contributes to ensuring safety gas supply in France

Full-signature real-time corrosion detection of underground casing pipes

NARCIS (Netherlands)

Yin, Jiming; Lu, Mi; Pineda de Gyvez, J.

2000-01-01

Corrosion monitoring and early detection of pits and wall thinning for casing pipes are considerably important to gas and petroleum industries since the frequently occurring corrosion at the internal or external parts of those steel casing pipes used in underground gas storage or oil fields causes

Structural analysis within the Rožná and Olší uranium deposits (Strážek Moldanubicum) for the estimation of deformation and stress conditions of underground gas storage

Czech Academy of Sciences Publication Activity Database

Ptáček, Jiří; Melichar, R.; Hájek, Antonín; Koníček, Petr; Souček, Kamil; Staš, Lubomír; Kříž, P.; Lazárek, J.

2013-01-01

Roč. 10, č. 2 (2013), s. 237-246 ISSN 1214-9705 Institutional support: RVO:68145535 Keywords : structural analysis * deformation * stress * underground gas storage Subject RIV: DH - Mining, incl. Coal Mining Impact factor: 0.667, year: 2013 http://www.irsm.cas.cz/materialy/acta_content/2013_02/acta_170_13_Ptacek_237-246.pdf

Streamlined approach for environmental restoration closure report for Corrective Action Unit No. 456: Underground storage tank release site 23-111-1, Nevada Test Site, Nevada

International Nuclear Information System (INIS)

1998-04-01

The underground storage tank (UST) release site 23-111-1 is located in Mercury, Nevada. The site is in Area 23 of the Nevada Test Site, (NTS) located on the north side of Building 111. The tank associated with the release was closed in place using cement grout on September 6, 1990. The tank was not closed by removal due to numerous active underground utilities, a high-voltage transformer pad, and overhead power lines. Soil samples collected below the tank bottom at the time of tank closure activities exceeded the Nevada Administrative Code Action Level of 100 milligrams per kilogram (mg/kg) for petroleum hydrocarbons. Maximum concentrations detected were 119 mg/kg. Two passive venting wells were subsequently installed at the tank ends to monitor the progress of biodegradation at the site. Quarterly air sampling from the wells was completed for approximately one year, but was discontinued since data indicated that considerable biodegradation was not occurring at the site

Advanced underground Vehicle Power and Control: The locomotive Research Platform

Energy Technology Data Exchange (ETDEWEB)

Vehicle Projects LLC

2003-01-28

Develop a fuelcell mine locomotive with metal-hydride hydrogen storage. Test the locomotive for fundamental limitations preventing successful commercialization of hydride fuelcells in underground mining. During Phase 1 of the DOE-EERE sponsored project, FPI and its partner SNL, completed work on the development of a 14.4 kW fuelcell power plant and metal-hydride energy storage. An existing battery-electric locomotive with similar power requirements, minus the battery module, was used as the base vehicle. In March 2001, Atlas Copco Wagner of Portland, OR, installed the fuelcell power plant into the base vehicle and initiated integration of the system into the vehicle. The entire vehicle returned to Sandia in May 2001 for further development and integration. Initial system power-up took place in December 2001. A revision to the original contract, Phase 2, at the request of DOE Golden Field Office, established Vehicle Projects LLC as the new prime contractor,. Phase 2 allowed industry partners to conduct surface tests, incorporate enhancements to the original design by SNL, perform an extensive risk and safety analysis, and test the fuelcell locomotive underground under representative production mine conditions. During the surface tests one of the fuelcell stacks exhibited reduced power output resulting in having to replace both fuelcell stacks. The new stacks were manufactured with new and improved technology resulting in an increase of the gross power output from 14.4 kW to 17 kW. Further work by CANMET and Hatch Associates, an engineering consulting firm specializing in safety analysis for the mining industry, both under subcontract to Vehicle Projects LLC, established minimum requirements for underground testing. CANMET upgraded the Programmable Logic Control (PLC) software used to monitor and control the fuelcell power plant, taking into account locomotive operator's needs. Battery Electric, a South Africa manufacturer, designed and manufactured (at no cost

Risk reduction in road and rail LPG transportation bij passive fire protection

NARCIS (Netherlands)

Molag e.a., M. (Menso)

2009-01-01

The potential reduction of risk in LPG (Liquified Petroleum Gas) road transport due to the adoption of passive fire protectionswas investigated. Experimental data available for small scale vessels fully engulfed by a fire were extended to real scale road and rail tankers through a finite elements

Risk reduction in road and rail LPG transportation by passive fire protection

NARCIS (Netherlands)

Paltrinieri, N.; Landucci, G.; Molag, M.; Bonvicini, S.; Spadoni, G.; Cozzani, V.

2009-01-01

The potential reduction of risk in LPG (Liquefied Petroleum Gas) road transport due to the adoption of passive fire protections was investigated. Experimental data available for small scale vessels fully engulfed by a fire were extended to real scale road and rail tankers through a finite elements

Support to the electric power, natural gas or liquefied petroleum gas (LPG) vehicles

International Nuclear Information System (INIS)

2006-01-01

This document brings together the different financial incentives proposed to the acquisition and utilization of electric power, natural gas or LPG vehicles. The financial assistance of the ADEME, the fiscal incentives and other proposals are detailed. (A.L.B.)

Development of simulated tank wastes for the US Department of Energy's Underground Storage Tank Integrated Demonstration

International Nuclear Information System (INIS)

Elmore, M.R.; Colton, N.G.; Jones, E.O.

1992-08-01

The purpose of the Underground Storage Tank Integrated Demonstration (USTID) is to identify and evaluate technologies that may be used to characterize, retrieve, treat, and dispose of hazardous and radioactive wastes contained in tanks on US Department of Energy sites. Simulated wastes are an essential component of the evaluation process because they provide controlled samples for technology assessment, and minimize costs and risks involved when working with radioactive wastes. Pacific Northwest Laboratory has developed a recipe to simulate Hanford single-shell tank, (SST) waste. The recipe is derived from existing process recipes, and elemental concentrations are based on characterization data from 18 SSTs. In this procedure, salt cake and metal oxide/hydroxide sludge are prepared individually, and mixed together at varying ratios depending on the specific tank, waste to be simulated or the test being conducted. Elemental and physical properties of the stimulant are comparable with analyzed tank samples, and chemical speciation in the simulant is being improved as speciation data for actual wastes become available. The nonradioactive chemical waste simulant described here is useful for testing technologies on a small scale

Geomechanical problems of an underground storage of spent nuclear fuel and their mathematic modelling

Directory of Open Access Journals (Sweden)

Antonín Hájek

2007-01-01

Full Text Available The paper is devoted to the use of mathematical modelling for analysis of the thermo-mechanical (T-M processes, which are relevant for the assessment of underground repositories of the spent nuclear fuel. Wes shall discuss mathematical formulation, numerical methods and parallel alghorithms, which are capable to solve large-scale complicated and coupled 3D problems. Particularly, we show an application of the described methods and parallel computer simulations for analysis of model problems concerning the Swedish KBS3 concept of underground repository.

Specific features of auxiliary water supply at underground NPPs

International Nuclear Information System (INIS)

Pergamenshchik, B.K.; Pavlov, A.S.

1991-01-01

Specific features of auxiliary water supply systems for underground NPPs related to peculiarities of NPP basis equipment arrangement, are considered. Circulation water supply scheme, in which water cooling storage basin (cooling towers) with operational area corresponding to NPP power is on the surface and has traditional design, is proposed. Sufficiently high efficiency of the arrangement proposed is proved

Monitoring and/or Detection of Wellbore Leakage In Energy Storage Wells

Science.gov (United States)

Ratigan, J.

2017-12-01

Energy (compressed natural gas, crude oil, NGL, and LPG) storage wells in solution-mined caverns in salt formations are required to be tested for integrity every five years. Rules promulgated for such testing typically assume the cavern interval in the salt formation is inherently impermeable, even though some experience demonstrates that this is not always the case. A protocol for testing the cavern impermeable hypothesis should be developed. The description for the integrity test of the "well" component of the well and cavern storage system was developed more than 30 years ago. However, some of the implicit assumptions inherent to the decades-old well test protocol are no longer applicable to the large diameter, high flow rate wells commonly constructed today. More detailed test protocols are necessary for the more contemporary energy storage wells.

National waste terminal storage conceptual reference repository description

International Nuclear Information System (INIS)

Odgers, I.L.; Collings, J.L.

1981-01-01

The conceptual reference repository description (CRRD) discusses, from a conceptual engineering standpoint, the structures, systems, equipment, and operations necessary to: (1) receive unreprocessed spent fuel assemblies in standard casks; (2) unload these assemblies; (3) place them in canisters; (4) transport the canisters to underground storage locations in the salt dome; and (5) place the canisters in terminal storage. The CRRD also elaborates on the concepts for retrieval and recovery of the spent fuel after burial and describes the development of the shafts and the underground areas, as well as the supporting operational utility and administrative features of the repository

Underground seasonal storage of industrial waste heat; Saisonale Speicherung industrieller Abwaerme im Untergrund

Energy Technology Data Exchange (ETDEWEB)

Reuss, M.; Mueller, J. [Bayerische Landesanstalt fuer Landtechnik, TU Muenchen-Weihenstephan, Freising (Germany)

1998-12-31

The thermal efficiency of subject systems, especially at higher temperatures is influenced by heat and humidity transport underground. Thermal conductivity and specific thermal capacity depend on the humidity content of the soil. A simulation model was developed that describes the coupled heat and humidity transport in the temperature range up to 90 C. This model will be validated in laboratory and field tests and then be used for designing and analysing underground stores. Pilot plants for the storage of industrial waste heat were designed and planned on the basis of this simulation. In both cases these are cogeneration plants whose waste heat was to be used for space heating and as process energy. Both plants have a very high demand of electric energy which is mostly supplied by the cogeneration plant. The waste heat is put into the store during the summer. In the winter heat is supplied by both the store and the cogeneration plant. In both cases the store has a volume of approx. 15,000 cubic metres with 140 and 210 pits located in a depth of 30 and 40 metres. The plants are used to carry out extensive measurements for the validation of simulation models. (orig.) [Deutsch] Die thermische Leistungsfaehigkeit solcher Systeme wird insbesondere im hoeheren Temperaturbereich durch den Waerme- und Feuchtetransport im Untergrund beeinflusst. Sowohl die Waermeleitfaehigkeit als auch die spezifische Waermekapazitaet sind vom Feuchtegehalt des Bodens abhaengig. Es wurde ein Simulationsmodell entwickelt, das den gekoppelten Waerme- und Feuchtetransport im Temperaturbereich bis 90 C beschreibt. Dieses Modell wird an Labor- und Feldexperimenten validiert und dient dann zur Auslegung und Analyse von Erdwaermesonden-Speichern. Basierend auf diesen theoretischen Grundlagenarbeiten wurden Pilotanlagen zur saisonalen Speicherung industrieller Abwaerme ausgelegt und geplant. In beiden Faellen handelt es sich um Kraft/Waermekopplungsanlagen, deren Abwaerme zur Gebaeudeheizung und

Structural analysis of underground gunite storage tanks. Environmental Restoration Program

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-01

This report documents the structural analysis of the 50-ft diameter underground gunite storage tanks constructed in 1943 and located in the Oak Ridge National Laboratory (ORNL) South Tank Farm, known as Facility 3507 in the 3500-3999 area. The six gunite tanks (W-5 through W-10) are spaced in a 2 {times} 3 matrix at 60 ft on centers with 6 ft of soil cover. Each tank (Figures 1, 2, and 3) has an inside diameter of 50 ft, a 12-ft vertical sidewall having a thickness of 6 in. (there is an additional 1.5-in. inner liner for much of the height), and a spherical domed roof (nominal thickness is 10 in.) rising another 6 ft, 3 in. at the center of the tank. The thickness of both the sidewall and the domed roof increases to 30 in. near their juncture. The tank floor is nominally 3-in. thick, except at the juncture with the wall where the thickness increases to 9 in. The tanks are constructed of gunite (a mixture of Portland cement, sand, and water in the form of a mortar) sprayed from the nozzle of a cement gun against a form or a solid surface. The floor and the dome are reinforced with one layer of welded wire mesh and reinforcing rods placed in the radial direction. The sidewall is reinforced with three layers of welded wire mesh, vertical {1/2}-in. rods, and 21 horizontal rebar hoops (attached to the vertical rods) post-tensioned to 35,000 psi stress. The haunch at the sidewall/roof junction is reinforced with 17 horizontal rebar hoops post-tensioned with 35,000 to 40,000 psi stress. The yield strength of the post-tensioning steel rods is specified to be 60,000 psi, and all other steel is 40,000 psi steel. The specified 28-day design strength of the gunite is 5,000 psi.

Structural analysis of underground gunite storage tanks. Environmental Restoration Program

International Nuclear Information System (INIS)

1995-08-01

This report documents the structural analysis of the 50-ft diameter underground gunite storage tanks constructed in 1943 and located in the Oak Ridge National Laboratory (ORNL) South Tank Farm, known as Facility 3507 in the 3500-3999 area. The six gunite tanks (W-5 through W-10) are spaced in a 2 x 3 matrix at 60 ft on centers with 6 ft of soil cover. Each tank (Figures 1, 2, and 3) has an inside diameter of 50 ft, a 12-ft vertical sidewall having a thickness of 6 in. (there is an additional 1.5-in. inner liner for much of the height), and a spherical domed roof (nominal thickness is 10 in.) rising another 6 ft, 3 in. at the center of the tank. The thickness of both the sidewall and the domed roof increases to 30 in. near their juncture. The tank floor is nominally 3-in. thick, except at the juncture with the wall where the thickness increases to 9 in. The tanks are constructed of gunite (a mixture of Portland cement, sand, and water in the form of a mortar) sprayed from the nozzle of a cement gun against a form or a solid surface. The floor and the dome are reinforced with one layer of welded wire mesh and reinforcing rods placed in the radial direction. The sidewall is reinforced with three layers of welded wire mesh, vertical 1/2-in. rods, and 21 horizontal rebar hoops (attached to the vertical rods) post-tensioned to 35,000 psi stress. The haunch at the sidewall/roof junction is reinforced with 17 horizontal rebar hoops post-tensioned with 35,000 to 40,000 psi stress. The yield strength of the post-tensioning steel rods is specified to be 60,000 psi, and all other steel is 40,000 psi steel. The specified 28-day design strength of the gunite is 5,000 psi

Emission Studies in CI Engine using LPG and Palm Kernel Methyl Ester as Fuels and Di-ethyl Ether as an Additive

Science.gov (United States)

Dora, Nagaraju; Jothi, T. J. Sarvoththama

2018-05-01

The present study investigates the effectiveness of using di-ethyl ether (DEE) as the fuel additive in engine performance and emissions. Experiments are carried out in a single cylinder four stroke diesel engine at constant speed. Two different fuels namely liquefied petroleum gas (LPG) and palm kernel methyl ester (PKME) are used as primary fuels with DEE as the fuel additive. LPG flow rates of 0.6 and 0.8 kg/h are considered, and flow rate of DEE is varied to maintain the constant engine speed. In case of PKME fuel, it is blended with diesel in the latter to the former ratio of 80:20, and DEE is varied in the volumetric proportion of 1 and 2%. Results indicate that for the engine operating in LPG-DEE mode at 0.6 kg/h of LPG, the brake thermal efficiency is lowered by 26%; however, NOx is subsequently reduced by around 30% compared to the engine running with only diesel fuel at 70% load. Similarly, results of PKME blended fuel showed a drastic reduction in the NOx and CO emissions. In these two modes of operation, DEE is observed to be significant fuel additive regarding emissions reduction.

Onsite gas storage for industrial customers

International Nuclear Information System (INIS)

Shikari, Y.A.

1990-01-01

The changing pattern of industrial gas marketing in the United States and other countries has placed new pressures on industrial users to assume responsibility for assuring their own supply. Technological changes in manufacturing processes have placed greater emphasis on assuring fuel quality and many processes can no longer tolerate near-substitutes such as distillate fuel oil and LPG. One way to take advantage of lower cost interruptible gas service contracts is to provide stand-by sources of gas onsite which can be used when the primary supply is curtailed. This paper describes the methods which an industrial gas consumer could use to store gas onsite (or close by an industrial factory) and their technical and economic advantages or limitations. The regulatory factors such as environmental and safety issues are reviewed and the advantages and disadvantages of each method are described. The application of emerging technologies such as storing natural gas on adsorbents at low pressure and solid absorption in LPG are reviewed and the research needed to make them acceptable is discussed. The potential applications in the marketplace are also discussed and the economics of onsite storage of natural gas is compared to other alternatives. (author). 11 refs, 5 figs, 1 tab

The influence of using LPG device on the CO2 emissions from personal passenger cars

Directory of Open Access Journals (Sweden)

Viliam Carach

2007-12-01

Full Text Available Traffic, mostly the air and car traffic is the biggest producer of CO2 (51% at present. CO2 is one of the most important greenhouse gases with more than 50 % of emissions contributing to this major global ecological problem. A rising concetration of CO2 in the atmosphere leads to higher global temperatures. The main problem is the rise of CO2 emissions in most developed countries despite international undertakings accepted in 80´s. This is the main reason for finding solutions to reduce the amount of CO2 emissions in the traffic. One of many solutions is the use of LPG fuel. The purpose of this article is to quantify the efficiency of using LPG in personal passenger cars.

A Review of Energy Storage Technologies

DEFF Research Database (Denmark)

Connolly, David

2010-01-01

A brief examination into the energy storage techniques currently available for the integration of fluctuating renewable energy was carried out. These included Pumped Hydroelectric Energy Storage (PHES), Underground Pumped Hydroelectric Energy Storage (UPHES), Compressed Air Energy Storage (CAES...... than PHES depending on the availability of suitable sites. FBES could also be utilised in the future for the integration of wind, but it may not have the scale required to exist along with electric vehicles. The remaining technologies will most likely be used for their current applications...

Yam Storability and Economic Benefits of Storage Under the Modern ...

African Journals Online (AJOL)

This paper examines yam storability and the economic benefits of storage under the modern (underground) and the traditional (yam barn) storage technologies in Southeastern Nigeria. Data were collected mainly from 55 respondents who were interviewed, as well as from measurement of storage parameters on yam ...

Radionuclides in an underground environment

International Nuclear Information System (INIS)

Thompson, J.L.

1996-01-01

In the 100 years since Becquerel recognized radioactivity, mankind has been very successful in producing large amounts of radioactive materials. We have been less successful in reaching a consensus on how to dispose of the billions of curies of fission products and transuranics resulting from nuclear weapons testing, electrical power generation, medical research, and a variety of other human endeavors. Many countries, including the United States, favor underground burial as a means of disposing of radioactive wastes. There are, however, serious questions about how such buried wastes may behave in the underground environment and particularly how they might eventually contaminate water, air and soil resources on which we are dependent. This paper describes research done in the United States in the state of Nevada on the behavior of radioactive materials placed underground. During the last thirty years, a series of ''experiments'' conducted for other purposes (testing of nuclear weapons) have resulted in a wide variety of fission products and actinides being injected in rock strata both above and below the water table. Variables which seem to control the movement of these radionuclides include the physical form (occlusion versus surface deposition), the chemical oxidation state, sorption by mineral phases of the host rock, and the hydrologic properties of the medium. The information gained from these studies should be relevant to planning for remediation of nuclear facilities elsewhere in the world and for long-term storage of nuclear wastes

Removal of CO2 by storage in the deep underground, chemical utilization and biofixation. Options for the Netherlands

International Nuclear Information System (INIS)

Over, J.A.; De Vries, J.E.; Stork, J.

1999-07-01

The Utrecht University in Utrecht, Netherlands, initially put the subject of CO2-storage on the agenda as a possible necessary policy element. During 1990/1991 a number of research institutes and engineering consultants carried out several studies. Also in 1991 the lEA Greenhouse Gas Group (IEA GHG) was initiated, including participation from The Netherlands. The Netherlands Agency for Energy and the Environment (Novem) and the Dutch Ministry of Economic Affairs both attended the meetings of the Executive Committee (ExCo) from the start. This Group started paying attention to the subject of CO2-capturing at large point sources (electricity stations). They then went subsequently from capturing from other (smaller and/or more diffuse) sources, ranking relative to other large scale options to combat or reduce CO2-emissions (i.e. vast areas of forest) to influence and controlling other 'greenhouse gases' such as methane. During 1992/1993 Novem prepared - on request of the Ministry of Economic Affairs - research proposals for investigations and demonstration projects, having a 10 to 15 year horizon, with regard to CO2-capturing technologies. In the beginning of 1994, the Dutch Ministry of Environment (VROM) put more emphasis on demonstration of the feasibility of CO2-storage. When the first 'Kok-government' (the so-called 'Purple Cabinet') came into being, attention shifted to studies on CO2-storage; the central question being whether there would be sufficient potential capacity if the necessity to store CO2 would ever occur. Within this framework Novem was authorized by the Ministry of Economic Affairs to carry out an investigation program on possibilities of CO2-storage. The present publication deals with the results of these studies. The main subject of investigation were: Storage in underground formations (depleted gas fields and aquifers) and the conditions under which this is feasible; Possibilities for enhanced gas recovery by carbon dioxide injection and its

Streamlined approach for environmental restoration closure report for Corrective Action Unit 464: Historical underground storage tank release sites, Nevada Test Site, Nevada

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-04-01

This report addresses the site characterization of two historical underground storage tank petroleum hydrocarbon release sites identified by Corrective Action Site (CAS) Numbers 02-02-03 and 09-02-01. The sites are located at the Nevada Test Site in Areas 2 and 9 and are concrete bunker complexes (Bunker 2-300, and 9-300). Characterization was completed using drilling equipment to delineate the extent of petroleum hydrocarbons at release site 2-300-1 (CAS 02-02-03). Based on site observations, the low hydrocarbon concentrations detected, and the delineation of the vertical and lateral extent of subsurface hydrocarbons, an ``A through K`` evaluation was completed to support a request for an Administrative Closure of the site.

Streamlined approach for environmental restoration closure report for Corrective Action Unit 464: Historical underground storage tank release sites, Nevada Test Site, Nevada

International Nuclear Information System (INIS)

1998-04-01

This report addresses the site characterization of two historical underground storage tank petroleum hydrocarbon release sites identified by Corrective Action Site (CAS) Numbers 02-02-03 and 09-02-01. The sites are located at the Nevada Test Site in Areas 2 and 9 and are concrete bunker complexes (Bunker 2-300, and 9-300). Characterization was completed using drilling equipment to delineate the extent of petroleum hydrocarbons at release site 2-300-1 (CAS 02-02-03). Based on site observations, the low hydrocarbon concentrations detected, and the delineation of the vertical and lateral extent of subsurface hydrocarbons, an ''A through K'' evaluation was completed to support a request for an Administrative Closure of the site

A study on the criterions of lean burn limit for an LPG EFI engine. Paper no. IGEC-1-140

International Nuclear Information System (INIS)

Li, L.; Wang, Z.; Xiao, Z.; Wang, H.; Deng, B.; Su, Y.

2005-01-01

Based on electronic low-pressure gaseous injection, the comparing analysis of several methods for the criterions of lean burn limit in an LPG engine is presented. Experiments are carried out in a single cylinder, four-stroke, water-cooled, 125cc engine with electronic LPG injection. According to the analysis of multi-parameters in and out cylinder, it shows that variation coefficient of indicated pressure which is the classical judgment of lean burn limit, the HC emission, HC emission rising gradient, the misfiring rate and the variation coefficient of the crank angle of the maximum combustion pressure can be as the criterions for lean burn limit. For the test engine, 15% as variation coefficient of indicative mean pressure, 500 x 10 -6 as HC emission, 2000 x 10 -6 as HC emission rising ratio, 1% as misfiring rate and 50% as variation coefficient of the crank angle of the maximum combustion pressure can be as the judgment criterions of LPG lean burn limits. (author)

Pilot research projects for underground disposal of radioactive wastes in the United States of America

International Nuclear Information System (INIS)

Stein, R.; Collyer, P.L.

1984-01-01

Disposal of commercial radioactive waste in the United States of America in a deep underground formation will ensure permanent isolation from the biosphere with minimal post-closure surveillance and maintenance. The siting, design and development, performance assessment, operation, licensing, certification and decommissioning of an underground repository have stimulated the development of several pilot research projects throughout the country. These pilot tests and projects, along with their resulting data base, are viewed as important steps in the overall location and construction of a repository. Beginning in the 1960s, research at pilot facilities has progressed from underground spent fuel tests in an abandoned salt mine to the production of vitrified nuclear waste in complex borosilicate glass logs. Simulated underground repository experiments have been performed in the dense basalts of Washington State, the volcanic tuffaceous rock of Nevada and both domal and bedded salts of Louisiana and Kansas. In addition to underground pilot in situ tests, other facilities have been constructed or modified to monitor the performance of spent fuel in dry storage wells and self-shielded concrete casks. As the National Waste Terminal Storage (NWTS) programme advances to the next stage of underground site characterization for each of three different geological sites, additional pilot facilities are under consideration. These include a Test and Evaluation Facility (TEF) for site verification and equipment performance and testing, as well as a salt testing facility for verification of in situ simulation equipment. Although not associated with the NWTS programme, the construction of the Waste Isolation Pilot Plant (WIPP) in the bedded salts of New Mexico is well under way for deep testing and experimentation with the defence programme's transuranic nuclear waste. (author)

Accessing leaking underground storage tank case studies and publications through the EPA's Computerized On-Line Information System (COLIS)

International Nuclear Information System (INIS)

Hillger, R.; Tibay, P.

1991-01-01

The US EPA's regulations for underground storage tanks (USTs) require corrective action to be taken in response to leaking USTs. Recent developments of UST programs nationwide as well as the introduction of new technologies to clean up UST sites have increased the diversity of experience levels among personnel involved with this type of work. The EPA's Computerized On-Line Information System (COLIS) has been developed to facilitate technology transfer among the personnel involved in UST cleanup. The system allows for the quick and simple retrieval of data relating to UST incidents, as well as other hazardous waste-related information. The system has been used by response personnel at all levels of government, academia, and private industry. Although it has been in existence for many years, users are just now realizing the potential wealth of information stored in this system. COLIS access can be accomplished via telephone lines utilizing a personal computer and a modem

The determination of aldehydes in the exhaust gases of LPG fuelled engines

NARCIS (Netherlands)

Rutten, G.A.F.M.; Burtner, C.W.J.; Visser, H.; Rijks, J.A.

1988-01-01

The exhaust gas of a LPG fuelled engine is drawn through two bubblers in series in an ice bath, and filled with saturated 2,4-dinitrophenylhydrazine in 2M HCl. After heating the derivatives are extracted with toluene-cyclohexane and 1l samples injected on-column on a OV1 capillary column. Using an

Flame stability and emission characteristics of turbulent LPG IDF in a backstep burner

Energy Technology Data Exchange (ETDEWEB)

S. Mahesh; D.P. Mishra [Indian Institute of Technology, Kanpur (India). Combustion Laboratory, Department of Aerospace Engineering

2008-09-15

The stability characteristics and emissions from turbulent LPG inverse diffusion flame (IDF) in a backstep burner are reported in this paper. The blow-off velocity of turbulent LPG IDF is observed to increase monotonically with fuel jet velocity. In contrast to normal diffusion flames (NDF), the flame in the present IDF burner gets blown out without getting lifted-off from the burner surface. The soot free length fraction, SFLF, defined as the ratio of visible premixing length, H{sub p}, to visible flame length, H{sub f}, is used for qualitative estimation of soot reduction in this IDF burner. The SFLF is found to increase with central air jet velocity indicating the occurrence of extended premixing zone in the vicinity of flame base. Interestingly, the soot free length fraction (SFLF) is found to be correlated well with the newly devised parameter, global momentum ratio. The peak value of EINOX happens to occur closer to stoichiometric overall equivalence ratio. 16 refs., 9 figs.

Feasibility study for bottled gas and LPG in Poland

International Nuclear Information System (INIS)

1992-04-01

With a total population of ca. 40 million, Poland has an annual consumption of liquefied petroleum gas amounting to 180,000 tons, used by 2.5 million bottled-gas consumers. The consumer pattern is expected to change, with an increasing market for gas for industrial purposes and for heating. Distribution systems will also change to include tank installations in many sizes and transport with large tank lorries. LPG is estimated to be competitive with other forms of energy, and the market is expected to increase to up to ca. 500,000 tons per year. Restricting factors are shortage of supply and lack of approved applications, transport equipment and tank facilities. A list of existing bottle gas companies and evaluation of the technical facilities in the Polish Oil and Gas Company in Gydnia are included. Bottled gas is currently distributed under normal conditions and, market prices for LPG have remained stable in Poland. Detailed studies of the current distribution network in the Suwalki area are given. It should be possible to extend the existing distribution network. A proposal for the establishment of standard tank installations and the gas supply for the town of Augustow is presented. Considerable investments will have to be made in terminals, tank plants and transport equipment, and international oil companies are expected to play an important role in this market. The European Bank for Restructuring and Development could possibly contribute to the financing of the pipe network. (AB)

1-GWh diurnal load-leveling superconducting magnetic energy storage system reference design. Appendix D: superconductive magnetic energy storage cavern construction methods and costs

International Nuclear Information System (INIS)

1979-09-01

The excavation and preparation of an underground cavern to contain a 1-GWh diurnal load-leveling Superconducting Magnetic Energy Storage (SMES) unit is examined. The cavern's principal function is to provide a rock structure for supporting the magnetic forces from the charged storage coil. Certain economic considerations indicate the refrigerator cold box for the helium system should also be underground. The study includes such a provision and considers, among other things, rock bolting, water seepage, concrete lining of the walls, steel bearing pads, a system to prevent freezing of the walls, a mining schedule, and costs

The 2003 guidebook of petroleum, gas and LPG. Every professional and web site in the oil and gas industry

International Nuclear Information System (INIS)

Legros, E.

2003-01-01

This guidebook is a joint special issue of 'Petrole et Gaz Informations' and 'GPL Actualites' journals. It is a complete and practical information tool which takes stock of: the economical activity during 2001 and 2002 (exploration/production, deep offshore activities, maritime transport and tanker-ships, European refining and new specifications, automotive fuels and future engines, lubricants, maritime transport of liquefied petroleum gas (LPG), storage facilities and capacity, new standards for bitumen binders, natural gas prospects, sustainable development and ethical investment, air pollution abatement etc..); the 2002 economical key-data of oil and gas summarized in an atlas of maps and statistical tables; a list of public organizations and associations, and of oil and gas companies settled in France; a list of companies involved in oil and gas equipments, services and products sorted by sector; and a yearbook of the oil and gas professionals with their corporate and web sites. (J.S.)

Potential Advantages of Underground Nuclear Parks

International Nuclear Information System (INIS)

Myers, Carl W.; Elkins, Ned Z.; Kunze, Jay F.; Mahar, James M.

2006-01-01

In this paper we argue that an underground nuclear park (UNP) could potentially lead to lower capital and operating cost for the reactors installed in the UNP compared to the traditional approach, which would be to site the reactors at the earth's surface at distributed locations. The UNP approach could also lead to lower waste management cost. A secondary benefit would be the increased margins of safety and security that would be realized simply as a consequence of siting the reactors underground. Lowered capital and operating cost for a UNP relative to traditional reactor siting is possible through the aggregate effect of the elimination of containment structures, in-place decommissioning, reduced physical security costs, reduced weather-related costs, reduced cost of liability insurance and reduced unit-cost for the nth reactor made possible through the continuous construction of multiple reactors at the same underground location. Other cost reductions might be possible through the transfer of the capital cost for part of the underground construction from the reactor owners to the owners of the UNP. Lower waste management cost is possible by siting the UNP at a location where there are geological and hydrological conditions suitable for hosting both the reactors and the repository for the waste from those reactors. After adequate storage and cooling, and assuming direct disposal, this would enable the spent fuel from the reactors to be transported directly to the repository and remain entirely underground during the transport process. Community concerns and transportation costs would be significantly reduced relative to current situations where the reactors are separated from the repository by long distances and populated areas. The concept for a UNP in bedded salt is used to develop a rough order of magnitude cost estimate for excavation of the reactor array portion of a UNP. Excavation costs appear to be only a small fraction of the overall power plant costs

Storage and security of supply

International Nuclear Information System (INIS)

Svensson, B.R.

1990-01-01

The paper considers the relationship between energy security and the consumption, supply and storage of natural gas, as agreed between the IEA Member countries. Additional supplies of natural gas should be obtained from as diverse sources as possible with emphasis on indigenous OECD sources. Instruments for coping with supply disruptions, such as underground storage of gas, interruptible gas sales, and dual-fired capabilities should be strengthened. These instruments, however, in combination with contractual swing factors, are also used to cope with fluctuations in demand for natural gas. The future demand and supply of natural gas in OECD Europe and North America is discussed. In OECD Europe the growth in residential and commercial demand is expected to be sustained, and, in both OECD Europe and North America, there is a further potential demand for gas for electricity generation. As residential and commercial demand (which is very temperature-dependent) grows, the need for storage facilities, interruptible sales contracts, dual-fired capabilities and swing factors in contracts will increase in order to balance the load. An expansion of gas demand for baseload electricity generation could, however, increase the load factor. Figures for the size of the storage capacity in 1987 and plans for future increases show that storage capacity is increasing. It is concluded that new underground storage represents an important contribution to the strengthening of each country's ability both to balance loads and to deal with supply disruptions. The IEA countries rely on the gas utilities to provide storage and other instruments for both purposes. (author). 2 figs, 3 tabs

Revised cost savings estimate with uncertainty for enhanced sludge washing of underground storage tank waste

International Nuclear Information System (INIS)

DeMuth, S.

1998-01-01

Enhanced Sludge Washing (ESW) has been selected to reduce the amount of sludge-based underground storage tank (UST) high-level waste at the Hanford site. During the past several years, studies have been conducted to determine the cost savings derived from the implementation of ESW. The tank waste inventory and ESW performance continues to be revised as characterization and development efforts advance. This study provides a new cost savings estimate based upon the most recent inventory and ESW performance revisions, and includes an estimate of the associated cost uncertainty. Whereas the author's previous cost savings estimates for ESW were compared against no sludge washing, this study assumes the baseline to be simple water washing which more accurately reflects the retrieval activity along. The revised ESW cost savings estimate for all UST waste at Hanford is $6.1 B ± $1.3 B within 95% confidence. This is based upon capital and operating cost savings, but does not include development costs. The development costs are assumed negligible since they should be at least an order of magnitude less than the savings. The overall cost savings uncertainty was derived from process performance uncertainties and baseline remediation cost uncertainties, as determined by the author's engineering judgment

A numerical study on the structural behavior of underground rock caverns for radioactive waste disposal

International Nuclear Information System (INIS)

Kim, Sun Hoon; Choi, Kyu Sup; Lee, Kyung Jin; Kim, Dae Hong

1991-01-01

In order to design safe and economical underground disposal structures for radioactive wastes, understanding the behavior of discontinuous rock masses is essential. This study includes discussions about the computational model for discontinuous rock masses and the structural analysis method for underground storage structures. Then, based on an engineering judgement a suitable selection and slight modifications on computational models and analysis methods have been made in order to analyze and understand the structural behavior of the rock cavern with discontinuities

UNDERGROUND

Energy Technology Data Exchange (ETDEWEB)

Anon.

1993-11-15

Full text: Cossetted deep underground, sheltered from cosmic ray noise, has always been a favourite haunt of neutrino physicists. Already in the 1930s, significant limits were obtained by taking a geiger counter down in Holborn 'tube' station, one of the deepest in London's underground system. Since then, neutrino physicists have popped up in many unlikely places - gold mines, salt mines, and road tunnels deep under mountain chains. Two such locations - the 1MB (Irvine/ Michigan/Brookhaven) detector 600 metres below ground in an Ohio salt mine, and the Kamiokande apparatus 1000m underground 300 km west of Tokyo - picked up neutrinos on 23 February 1987 from the famous 1987A supernova. Purpose-built underground laboratories have made life easier, notably the Italian Gran Sasso Laboratory near Rome, 1.4 kilometres below the surface, and the Russian Baksan Neutrino Observatory under Mount Andyrchi in the Caucasus range. Gran Sasso houses ICARUS (April, page 15), Gallex, Borexino, Macro and the LVD Large Volume Detector, while Baksan is the home of the SAGE gallium-based solar neutrino experiment. Elsewhere, important ongoing underground neutrino experiments include Soudan II in the US (April, page 16), the Canadian Sudbury Neutrino Observatory with its heavy water target (January 1990, page 23), and Superkamiokande in Japan (May 1991, page 8)

Alternative utilization of underground spaces with abandoned mine openings

Energy Technology Data Exchange (ETDEWEB)

Chung, So Keul; Cho, Won Jai; Han, Kong Chang; Choi, Sung Oong [Korea Institute of Geology Mining and Materials, Taejon (Korea)

1998-12-01

Utilization of the openings of the abandoned mines could be planned by the principal parameters such as location and geotechnical impact. The local governments have not only to lead the each stage of the utilization project from the very beginning of conceptual design up to the construction stage, but also to promote the project for the development of public purpose. The possible tentative candidates for the utilization of the abandoned mine openings which are supported by the local governments could be summarized as follows. a. The Gahak mine of Kwangmyung, Kyunggi: The mine caverns which have been served as the storage of the pickled fishes, could be reexcavated by taking into consideration the geotechnical parameters for the public use such as: 1) Training center for the youth, 2) Fermentation and storehouse of marine products, 3) Sightseeing resort, 4) Sports and leisure complex, 5) Underground parking lot, 6) Underground shopping mall and chilled room storage, 7) Library, concert hall and museum. b. Hamtae mine of Taebaek, Kangwon: The Hambaek main haulage way and its shaft should be investigated in detail in order to find out a possible use as the underground challenging park of the coal mining operation. c. Mines of Boryung and Hongsung, Chungnam: Lots of mine caverns have been used as the storehouse for the pickled shrimp. However, they have to be promoted to a large scale industries. d. Imgok mine of Kwangju and Palbong mine of Jeongeup, Chunbuk: Mine caverns which have been used as the storehouse of pickles, need a detailed investigation for alternative promotion. e. Yongho mine of Pusan Dalsung mine of Taegu: Both of the mines are located near metropolitan communities. Reconstruction of the old mine caverns of the Yongho mine is highly recommended for a public use. The caverns of the Dalsung mine could be utilized as the storage facilities. Detailed geotechnical survey and sit investigation could be suggested to design the recommended facilities for both

Economic efficiency of underground natural gas storage: The case of Canada

International Nuclear Information System (INIS)

Charette, Y.

1990-01-01

The paper describes the current situation of natural gas storage in Canada and attempts to provide valuable information and analytical tools so that the key players, including government and industry, will be in a better position to make enlightened choices for future investments in natural gas storage. Central to the analysis of the efficiency of storage is the notion of efficient peak-load pricing. It is usually recognized that storage may be efficient or welfare increasing because, with fixed consumption, it may allow the substitution of cheaper off-peak production for more costly production. The theoretical conclusions are used of a number of static peak-load pricing models, as well as investment decision models, to analyze the various costs and benefits of storage. The main conclusion is made that, when storage is possible, the welfare maximizing peak/off-peak price differential can be reduced, and therefore, storage can increase the efficiency of the gas transmission system. 10 refs, 2 figs, 5 tabs

The cost-effectiveness of a steel tube or a buffer zone for mitigating blast effects on a building spanning an underpass with transport of LPG

NARCIS (Netherlands)

Suddle, S.I.; Weerheijm, J.; Berg, A.C. van den

2010-01-01

The use of space is being intensified near and above transport routes of hazardous materials. In The Netherlands, some buildings are even realized above infrastructure with transport of hazardous materials like LPG. An accident with an LPG-tank may result in a BLEVE, causing injuries and large

Influence of film thickness and Fe doping on LPG sensing properties of Mn3O4 thin film grown by SILAR method

Science.gov (United States)

Belkhedkar, M. R.; Ubale, A. U.

2018-05-01

Nanocrystalline Fe doped and undoped Mn3O4 thin films have been deposited by Successive Ionic Layer Adsorption and Reaction (SILAR) method onto glass substrates using MnCl2 and NaOH as cationic and anionic precursors. The grazing incidence X-ray diffraction (GIXRD) and field emission scanning electron microscopy (FESEM)) have been carried out to analyze structural and surface morphological properties of the films. The LPG sensing performance of Mn3O4thin films have been studied by varying temperature, concentration of LPG, thickness of the film and doping percentage of Fe. The LPG response of the Mn3O4thin films were found to be enhances with film thickness and decreases with increased Fe doping (0 to 8 wt. %) at 573 K temperature.

Modelling of seismic reflection data for underground gas storage in the Pečarovci and Dankovci structures - Mura Depression

Directory of Open Access Journals (Sweden)

Andrej Gosar

1995-12-01

Full Text Available Two antiform structures in the Mura Depression were selected as the most promising in Slovenia for the construction of an underground gas storage facility in an aquifer. Seventeen reflection lines with a total length of 157km were recorded, and three boreholes were drilled. Structural models corresponding to two different horizons (the pre-Tertiary basement and the Badenian-Sarmatianboundary were constructed using the Sierra Mimic program. Evaluation of different velocity data (velocity analysis, sonic log, the down-hole method, and laboratory measurements on cores was carried out in order to perform correct timeto-depth conversion and to estabUsh lateral velocity variations. The porous rock in Pečarovci structure is 70m thick layer of dolomite, occurring at a depth of 1900m, whereas layers of marl, several hundred meter thick, represent the impermeable cap-rock. Due to faults, the Dankovci structure, at a depth of 1200m,where the reservoir rocks consist of thin layers of conglomerate and sandstone,was proved to be less reliable. ID synthetic seismograms were used to correlatethe geological and seismic data at the borehole locations, especially at intervals with thin layers. The raytracing method on 2D models (the Sierra Quik packagewas applied to confirm lateral continuity of some horizons and to improve the interpretation of faults which are the critical factor for gas storage.

A study on damage effect from boiling liquid expanding vapor explosion(Believe) of LPG charging facility

Energy Technology Data Exchange (ETDEWEB)

Roh, Sam Kew; Ham, Eun Gu [Dept. of Architectural Engineering, Kwangwoon University (Korea); Kim, Tae Hwan [Automation System Research Institute, Seoul (Korea)

1999-12-01

The LPG refueling station's explosion at Bucheon city was a major accident which with rare frequency of occurrence and large damage effect. Therefore, to prevent similar accident in the future from LPG charging stations which located in urban area. It needs to identify the damage effects of such facilities by comparing theoretically quantities risk and actual damage. The BLEVE effects from the accident showed similar damage effect in case of heat flux, however, the overpressure level reflected at the reduced distance by 15%. The structure damage to the near by area showed comparatively large heat radiation damage to the concrete structure strength and shape changes through heat flux while the overpressure effect was small. 13 refs., 4 figs., 4 tabs.

Role of LPG as an energy substitute in Algeria; Role des G.P.L. comme energie de substitution en Algerie

Energy Technology Data Exchange (ETDEWEB)

Boukadoum, Abdelhamid; Houghlaouene, Samir

2010-09-15

Algeria is a leader country in LPG industry. The availability of resources and the upstream production development efforts have oriented the large energy choices in terms of domestic market need satisfaction. LPG (propane and butane) plays a massive role in the change towards clean energy (case of LPG versus gas) and towards more practical energy (i.e. the case of bulk propane versus the packed butane, or versus natural gas). [French] L'Algerie est un pays leader dans l'industrie des GPL. La disponibilite des ressources et les efforts de developpement de la production en amont ont oriente les grands choix energetiques en matiere de satisfaction des besoins du marche domestique. En effet, les GPL (propane et butane) jouent un role majeur dans la substitution vers les sources d'energie propres (cas du GPL/C par rapport aux essences) et vers des energies plus commodes (par exemple le cas du propane vrac par rapport au butane conditionne, voire par rapport au gaz naturel).

Materials used in refrigerated storage system

Energy Technology Data Exchange (ETDEWEB)

Abakians, H

1970-09-01

Applications of cryogenic technology have increased at a phenomenal rate during the past decade. With the installation of a number of refrigerated storage tanks in Iran, e.g., LPG storage at Bandar Mah Shahr and Kharg Is., and ammonia storage at Bandar Shahpour, it is appropriate to review the materials used in constructing low temperature storage systems. In order to have an economical fully refrigerated storage installation without assuming the risk of brittle fracture, appropriate notch-tough material should be selected for the important and highly stressed components. In general, the lower the operating temperature, the more expensive is the material to be used. Hence, care should be taken to select the required material in such a manner that it will be suitable for the operating temperature and not lower. The most economical materials for low temperatures are steels. Ordinary carbon steel can be used down to -20$F and the Killed carbon steel down to -50$F. Nickel steels (2 1/4%) can be used down to -75$ to 100$F, Nickel steels (3 1/2%) down to -150$F, and 9% nickel steels down to 1,320$F. Stainless and aluminum alloys can be used down to -423$F. Tabular data give some commonly used materials in low temperature and cryogenic services with their lowest allowable temperature, tensile strength, and relative cost.

Development of database systems for safety of repositories for disposal of radioactive wastes

Energy Technology Data Exchange (ETDEWEB)

Lee, Yeong Hoon; Han, Jeong Sang; Shin, Hyeon Joon; Ham, Sang Won; Moon, Sang Kee [Yonsei Univ., Seoul (Korea, Republic of)

1998-03-15

In this study, contents and survey and supervision items in each part are selected to avoid overlap between different parts referring national lows, criterion, and guidance related to atomic energy. The items consist of climatology, hydrology, geology, seismology, engineering geology, geochemistry, and civil and social parts. Based on these items, general study and systematic control related to the stability of disposal sites os established and as specific region required with the properties that is similar to properties of radioactive waste disposal sites, Ulsan region equipped with LPG underground storage facility was selected and its datum were surveyed and inputted. So propriety of established database system was proved.

Development of database systems for safety of repositories for disposal of radioactive wastes

International Nuclear Information System (INIS)

Lee, Yeong Hoon; Han, Jeong Sang; Shin, Hyeon Joon; Ham, Sang Won; Moon, Sang Kee

1998-03-01

In this study, contents and survey and supervision items in each part are selected to avoid overlap between different parts referring national lows, criterion, and guidance related to atomic energy. The items consist of climatology, hydrology, geology, seismology, engineering geology, geochemistry, and civil and social parts. Based on these items, general study and systematic control related to the stability of disposal sites os established and as specific region required with the properties that is similar to properties of radioactive waste disposal sites, Ulsan region equipped with LPG underground storage facility was selected and its datum were surveyed and inputted. So propriety of established database system was proved

PEP cooling water systems and underground piped utilities design criteria report

International Nuclear Information System (INIS)

Hall, F.; Robbins, D.

1975-10-01

This paper discusses the cooling systems required by the PEP Storage Ring. Particular topics discussed are: Cooling tower systems, RF cavity and vacuum chamber LCW cooling systems, klystron and ring magnet LLW cooling systems, Injection magnet LCW Cooling Systems; PEP interaction area detector LCW Cooling Systems; and underground piped utilities. 1 ref., 20 figs

High-Level Radioactive Waste: Safe Storage and Ultimate Disposal.

Science.gov (United States)

Dukert, Joseph M.

Described are problems and techniques for safe disposal of radioactive waste. Degrees of radioactivity, temporary storage, and long-term permanent storage are discussed. Included are diagrams of estimated waste volumes to the year 2000 and of an artist's conception of a permanent underground disposal facility. (SL)

Economic and technical feasibility study of compressed air storage

Energy Technology Data Exchange (ETDEWEB)

1976-03-01

The results of a study of the economic and technical feasibility of compressed air energy storage (CAES) are presented. The study, which concentrated primarily on the application of underground air storage with combustion turbines, consisted of two phases. In the first phase a general assessment of the technical alternatives, economic characteristics and the institutional constraints associated with underground storage of compressed air for utility peaking application was carried out. The goal of this assessment was to identify potential barrier problems and to define the incentive for the implementation of compressed air storage. In the second phase, the general conclusions of the assessment were tested by carrying out the conceptual design of a CAES plant at two specific sites, and a program of further work indicated by the assessment study was formulated. The conceptual design of a CAES plant employing storage in an aquifer and that of a plant employing storage in a conventionally excavated cavern employing a water leg to maintain constant pressure are shown. Recommendations for further work, as well as directions of future turbo-machinery development, are made. It is concluded that compressed air storage is technically feasible for off-peak energy storage, and, depending on site conditions, CAES plants may be favored over simple cycle turbine plants to meet peak demands. (LCL)

UNDERGROUND

International Nuclear Information System (INIS)

Anon.

1993-01-01

Full text: Cossetted deep underground, sheltered from cosmic ray noise, has always been a favourite haunt of neutrino physicists. Already in the 1930s, significant limits were obtained by taking a geiger counter down in Holborn 'tube' station, one of the deepest in London's underground system. Since then, neutrino physicists have popped up in many unlikely places - gold mines, salt mines, and road tunnels deep under mountain chains. Two such locations - the 1MB (Irvine/ Michigan/Brookhaven) detector 600 metres below ground in an Ohio salt mine, and the Kamiokande apparatus 1000m underground 300 km west of Tokyo - picked up neutrinos on 23 February 1987 from the famous 1987A supernova. Purpose-built underground laboratories have made life easier, notably the Italian Gran Sasso Laboratory near Rome, 1.4 kilometres below the surface, and the Russian Baksan Neutrino Observatory under Mount Andyrchi in the Caucasus range. Gran Sasso houses ICARUS (April, page 15), Gallex, Borexino, Macro and the LVD Large Volume Detector, while Baksan is the home of the SAGE gallium-based solar neutrino experiment. Elsewhere, important ongoing underground neutrino experiments include Soudan II in the US (April, page 16), the Canadian Sudbury Neutrino Observatory with its heavy water target (January 1990, page 23), and Superkamiokande in Japan (May 1991, page 8)

Experimental and analytical investigation of thermal coating effectiveness for 3 m{sup 3} LPG tanks engulfed by fire

Energy Technology Data Exchange (ETDEWEB)

Landucci, Gabriele [CONPRICI - Dipartimento di Ingegneria Chimica, Chimica Industriale e Scienza dei Materiali, Universita degli Studi di Pisa, via Diotisalvi n.2, 56126 Pisa (Italy); Molag, Menso; Reinders, Johan [Nederlandse Organisatie voor toegepast-natuurwetenschappelijk onderzoek TNO, Laan van Westenenk 501, P.O. Box 342, 7300 AH Apeldoorn (Netherlands); Cozzani, Valerio [CONPRICI - Dipartimento di Ingegneria Chimica, Mineraria e delle Tecnologie Ambientali, Alma Mater Studiorum, Universita di Bologna, via Terracini n.28, 40131 Bologna (Italy)], E-mail: valerio.cozzani@unibo.it

2009-01-30

Two large-scale diesel pool fire engulfment tests were carried out on LPG tanks protected with intumescing materials to test the effectiveness of thermal coatings in the prevention of hot BLEVE accidental scenarios in the road and rail transport of LPG. A specific test protocol was defined to enhance reproducibility of experimental tests. The geometrical characteristics of the test tanks were selected in order to obtain shell stresses similar to those present in full-size road tankers complying to ADR standards. In order to better understand the stress distribution on the vessel and to identify underlying complicating phenomena, a finite element model was also developed to better analyze the experimental data. A non-homogeneous and time-dependent effectiveness of the fire protection given by the intumescing coating was evidenced both by finite element simulations and by the analysis of the coating after the tests. The results of the fire tests pointed out that the coating assured an effective protection of the tanks, consistently increasing the expected time to failure. The data obtained suggest that the introduction of fire protection coatings may be a viable route to improve the safety of the LPG distribution chain.

Design Guidelines for Bus Transit Systems Using Liquefied Petroleum Gas (LPG) as an Alternative Fuel.

Science.gov (United States)

1996-09-01

The use of alternative fuels to power transit buses is steadily increasing. Several fuels, including Liquefied Petroleum Gas (LPG), Compressed Natural Gas (CNG), and Methanol/Ethanol, are already being used in buses. At present, there do not exist co...

Investigating the effects of LPG on spark ignition engine combustion and performance

International Nuclear Information System (INIS)

Bayraktar, Hakan; Durgun, Orhan

2005-01-01

A quasi-dimensional spark ignition (SI) engine cycle model is used to predict the cycle, performance and exhaust emissions of an automotive engine for the cases of using gasoline and LPG. Governing equations of the mathematical model mainly consist of first order ordinary differential equations derived for cylinder pressure and temperature. Combustion is simulated as a turbulent flame propagation process and during this process, two different thermodynamic regions consisting of unburned gases and burned gases that are separated by the flame front are considered. A computer code for the cycle model has been prepared to perform numerical calculations over a range of engine speeds and fuel-air equivalence ratios. In the computations performed at different engine speeds, the same fuel-air equivalence ratios are selected for each fuel to make realistic comparisons from the fuel economy and fuel consumption points of view. Comparisons show that if LPG fueled SI engines are operated at the same conditions with those of gasoline fueled SI engines, significant improvements in exhaust emissions can be achieved. However, variations in various engine performance parameters and the effects on the engine structural elements are not promising

Novel sensing approach for LPG leakage detection: Part I: Operating Mechanism and Preliminary Results

KAUST Repository

Mukhopadhyay, Subhas; Nag, Anindya; Zia, Asif; Li, Xie; Kosel, Jü rgen

2015-01-01

Gas sensing technology has been among the topical research work for quite some time. This paper showcases the research done on the detection mechanism of leakage of domestic cooking gas at ambient conditions. MEMS-based interdigital sensors were fabricated on oxidized single crystal silicon surfaces by maskless photolithography technique. The electrochemical impedance analysis of these sensors was done to detect liquefied petroleum gas (LPG) with and without coated particles of tin oxide (SnO2) in form of thin layer.A thin-film of SnO2 was spin-coated on the sensing surface of the interdigital sensor to induce selectivity to LPG that consists of a 60/40 mixture of propane and butane respectively. The paper reports a novel strategy for gas detection under ambient temperature and humidity conditions. The response time of the coated sensor was encouraging and own a promising potential to the development of a complete efficient gas sensing system.

Novel sensing approach for LPG leakage detection: Part I: Operating Mechanism and Preliminary Results

KAUST Repository

Mukhopadhyay, Subhas

2015-10-30

Gas sensing technology has been among the topical research work for quite some time. This paper showcases the research done on the detection mechanism of leakage of domestic cooking gas at ambient conditions. MEMS-based interdigital sensors were fabricated on oxidized single crystal silicon surfaces by maskless photolithography technique. The electrochemical impedance analysis of these sensors was done to detect liquefied petroleum gas (LPG) with and without coated particles of tin oxide (SnO2) in form of thin layer.A thin-film of SnO2 was spin-coated on the sensing surface of the interdigital sensor to induce selectivity to LPG that consists of a 60/40 mixture of propane and butane respectively. The paper reports a novel strategy for gas detection under ambient temperature and humidity conditions. The response time of the coated sensor was encouraging and own a promising potential to the development of a complete efficient gas sensing system.

Underground transmission tomography

International Nuclear Information System (INIS)

Geibka, C.

1990-01-01

Several underground tomographic transmission surveys have been carried out. Targets were cavities, ore veins and fault zones. Examples from measurements in a german heavy/fluor spar mine a lead/zinc mine and a rock laboratory of the Swiss National Cooperative for the Storage of Radioactive waste are presented. Measurements were carried out between boreholes and road ways. The recording equipment was the intrinsically safe SEAMEX85 system built and sold by WBK. Receivers were mounted in a chain of 6 two-component probes. Sources were an inhole hammer a sledge hammer a sparker and explosives from a single detonator to 180 g depending on the distance and absorption of the rock material. Cavities showed very distinct velocity reductions between 30 and 50%. Different vein material showed velocity reduction as well as velocity increase relative to the surrounding rock

Thermal hardening of saturated clays. Application to underground storage of radioactive wastes

International Nuclear Information System (INIS)

Picard, Jean-Marc

1994-01-01

Saturated clays submitted to constant mechanical loading and slow temperature increase frequently undergo irreversible contractions. This phenomena is described here by means of a change of plastic limits induced by temperature only, called thermal hardening. Constitutive laws adapted to this kind of plastic behaviour can be formulated within a general framework that satisfies thermodynamical principles. It shows that this coupling results from the presence of a latent heat during the isothermal hardening of plastic limits. A thermomechanical extension of Cam Clay model is then proposed and used in the analysis of laboratory thermomechanical tests performed on clay materials. Making use of tests already published, we show the adequacy of the concept of thermal hardening for clay behaviour. Some clay from deep geological formation considered for the disposal of radioactive waste exhibit thermal hardening in laboratory tests. The consequences for the underground storage facilities during the thermal loading created by the waste are investigated by means of in situ tests as well as numerical computation. The measurement around a heating probe buried in the clay mass demonstrate the significance of thermo-hydro-mechanical couplings. An accurate understanding of in situ measurements is achieved by means of numerical modeling in which the interaction between the various loading of the tests (excavation, pore pressure seepage, and heating) is carefully taken into account. Thermal hardening of the clay appears to be of little influence in these in situ tests. On the other hand, the magnitude of thermo-hydro-mechanical couplings observed in situ are higher than might have been expected from laboratory tests. A more accurate prediction is obtained if one takes into account the more stiffer behaviour of clays when they are subjected to small deformations. (authors)

The underground heat storage for solar-assisted district heating in Neckarsulm. First measuring results; Der Erdsonden-Waermespeicher fuer die solarunterstuetzte Nahwaermeversorgung in Neckarsulm. Erste Messergebnisse

Energy Technology Data Exchange (ETDEWEB)

Seiwald, H.; Hahne, E. [Stuttgart Univ. (Germany). Inst. fuer Thermodynamik und Waermetechnik

1998-12-31