WorldWideScience

Sample records for underground coal-mining industry

  1. Industrial Internet of Things: (IIoT) applications in underground coal mines.

    Science.gov (United States)

    Zhou, C; Damiano, N; Whisner, B; Reyes, M

    2017-12-01

    The Industrial Internet of Things (IIoT), a concept that combines sensor networks and control systems, has been employed in several industries to improve productivity and safety. U.S. National Institute for Occupational Safety and Health (NIOSH) researchers are investigating IIoT applications to identify the challenges of and potential solutions for transferring IIoT from other industries to the mining industry. Specifically, NIOSH has reviewed existing sensors and communications network systems used in U.S. underground coal mines to determine whether they are capable of supporting IIoT systems. The results show that about 40 percent of the installed post-accident communication systems as of 2014 require minimal or no modification to support IIoT applications. NIOSH researchers also developed an IIoT monitoring and control prototype system using low-cost microcontroller Wi-Fi boards to detect a door opening on a refuge alternative, activate fans located inside the Pittsburgh Experimental Mine and actuate an alarm beacon on the surface. The results of this feasibility study can be used to explore IIoT applications in underground coal mines based on existing communication and tracking infrastructure.

  2. Developments in the application of underground battery vehicles in the UK coal mining industry

    Energy Technology Data Exchange (ETDEWEB)

    Fortune, J A.B.; Crawshaw, S A.M. [Long-Airdox International Ltd. (United Kingdom)

    1996-10-01

    Trackless battery powered haulage vehicles have been in operation in British coal mines principally for longwall face transfer and personnel transportation. Changes within the industry have resulted in the introduction of room and pillar coal mining methods and the introduction of increasingly heavier longwall roof supports. This has resulted in the introduction of: battery powered coal haulage machines, which, without the need for trailing cables, increase productivity within room and pillar mining; and battery powered longwall shield haulers which are capable of carrying the heaviest shield supports currently being utilised within the British coal mining industry. The conventional machines have been adapted from an American design to meet the requirements of European legislation. This has seen the emphasis being placed upon the supplier with the European Machinery Directive being introduced, necessitating the assigning of a `CE` mark to each vehicle. Battery vehicle technology has advanced to meet the demands of the ever changing market and will no doubt be further adapted to meet the requirement of the British coal mining industry. 1 ref., 12 figs., 3 tabs.

  3. 78 FR 58264 - Refuge Alternatives for Underground Coal Mines

    Science.gov (United States)

    2013-09-23

    ... Refuge Alternatives for Underground Coal Mines AGENCY: Mine Safety and Health Administration, Labor... Agency's Request for Information (RFI) on Refuge Alternatives for Underground Coal Mines. This extension... Alternatives for Underground Coal Mines. The RFI comment period had been scheduled to close on October 7, 2013...

  4. 78 FR 48591 - Refuge Alternatives for Underground Coal Mines

    Science.gov (United States)

    2013-08-08

    ... Administration 30 CFR Parts 7 and 75 Refuge Alternatives for Underground Coal Mines; Proposed Rules #0;#0;Federal... Underground Coal Mines AGENCY: Mine Safety and Health Administration, Labor. ACTION: Limited reopening of the... for miners to deploy and use refuge alternatives in underground coal mines. The U.S. Court of Appeals...

  5. 78 FR 73471 - Refuge Alternatives for Underground Coal Mines

    Science.gov (United States)

    2013-12-06

    ... Refuge Alternatives for Underground Coal Mines AGENCY: Mine Safety and Health Administration, Labor... Agency's Request for Information (RFI) on Refuge Alternatives for Underground Coal Mines. This extension...), MSHA published a Request for Information on Refuge Alternatives for Underground Coal Mines. The RFI...

  6. Design Criteria for Wireless Mesh Communications in Underground Coal Mines

    OpenAIRE

    Griffin, Kenneth Reed

    2009-01-01

    The Mine Improvement and New Emergency Response (MINER) Act of 2006 was enacted in response to several coal mining accidents that occurred in the beginning of 2006. The MINER Act does not just require underground mines to integrate wireless communication and tracking systems, but aims to overall enhance health and safety in mining at both surface and underground operations. In 2006, the underground communication technologies available to the mining industry had inherent problems that limited ...

  7. 78 FR 68783 - Refuge Alternatives for Underground Coal Mines

    Science.gov (United States)

    2013-11-15

    ... Alternatives for Underground Coal Mines AGENCY: Mine Safety and Health Administration, Labor. ACTION: Reopen... coal mines. The U.S. Court of Appeals for the District of Columbia Circuit remanded a training... for refuge alternatives in underground coal mines. On January 13, 2009, the United Mine Workers of...

  8. Underground coal mining technology - the future

    Energy Technology Data Exchange (ETDEWEB)

    Lama, R P [Kembla Coal and Coke Pty Limited, Wollongong, NSW (Australia)

    1989-01-01

    Discusses development of underground coal mining in Australia in the last four decades. The following aspects are reviewed: technology for underground mining (longwall mining, unidirectional cutting, bidirectional cutting, operation of more than one shearer on a working face, optimum dimensions of longwall blocks), longwall productivity (productivity increase will depend on increasing the availability factor of equipment, reducing failures due to human errors, organizational models, improving on-site decision making, improving monitoring, maintenance, planning and scheduling, concept of 'Transparent Mine'), roadway development systems (types of heading machines, standard systems for mine drivage and roof bolting and their productivity), size of coal mines, man and material transport systems (20,000-30,000 t/d from a single longwall face, mine shafts with a diameter 9-10 m), mine layout design (layout of longwall blocks, main intakes and returns situated in rock layers), mine environmental systems (ventilation systems, gas control), management, training and interpersonal relationships. Future coal mines will be developed with an integral capacity of 8-10 Mt/a from a single longwall operation with main development arteries placed in rocks. Development of gate roadways will require novel solutions with continuous cutting, loading and bolting. Information technology, with the concept of 'transparent mine', will form the backbone of decision making.

  9. 75 FR 39735 - Mandatory Reporting of Greenhouse Gases From Magnesium Production, Underground Coal Mines...

    Science.gov (United States)

    2010-07-12

    ... sectors of the economy, including fossil fuel suppliers, industrial gas suppliers, and direct emitters of... Part II Environmental Protection Agency 40 CFR Part 98 Mandatory Reporting of Greenhouse Gases From Magnesium Production, Underground Coal Mines, Industrial Wastewater Treatment, and Industrial...

  10. Prevention and protection against propagation of explosionsin underground coal mines

    Directory of Open Access Journals (Sweden)

    Л. М. Пейч

    2017-06-01

    Full Text Available Over the past century, the coal mining industry experienced a large number of explosions leading to a considerable loss of life. The objective of this study is preventing the propagation of methane and/or coal dust explosions through the use of passive water barriers and its implementation to the Spanish coal mining industry. Physical and chemical properties, flammability and explosibility parameters of typical Spanish coals are presented. In this paper,   a flexible approach to meet the requirements of the EN-14591-2:2007 standard is presented for the very specific local conditions, characterized by small cross-sections galleries, vertical seem, use of explosives, etc. Authors have proven the viability of standard requirements to the typical roadway from Spanish underground mines, considering realistic roadway lengths as well as available cross-sections taking into account ubiquitous obstacles such as: locomotives, conveyor belt, ventilation ducts, etc.

  11. High radon exposure in a Brazilian underground coal mine

    International Nuclear Information System (INIS)

    Veiga, L H S; Melo, V; Koifman, S; Amaral, E C S

    2004-01-01

    The main source of radiation exposure in most underground mining operations is radon and radon decay products. The situation of radon exposure in underground mining in Brazil is still unknown, since there has been no national regulation regarding this exposure. A preliminary radiological survey in non-uranium mines in Brazil indicated that an underground coal mine in the south of Brazil had high radon concentration and needed to be better evaluated. This paper intends to present an assessment of radon and radon decay product exposure in the underground environment of this coal mining industry and to estimate the annual exposure to the workers. As a product of this assessment, it was found that average radon concentrations at all sampling campaign and excavation sites were above the action level range for workplaces of 500-1500 Bq m -3 recommended by the International Commission on Radiological Protection-ICRP 65. The average effective dose estimated for the workers was almost 30 times higher than the world average dose for coal miners

  12. 30 CFR 75.1907 - Diesel-powered equipment intended for use in underground coal mines.

    Science.gov (United States)

    2010-07-01

    ... underground coal mines. 75.1907 Section 75.1907 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Diesel-Powered Equipment § 75.1907 Diesel-powered equipment intended for use in underground coal mines. (a) As of...

  13. A novel method for estimating methane emissions from underground coal mines: The Yanma coal mine, China

    Science.gov (United States)

    Ji, Zhong-Min; Chen, Zhi-Jian; Pan, Jie-Nan; Niu, Qing-He

    2017-12-01

    As the world's largest coal producer and consumer, China accounts for a relatively high proportion of methane emissions from coal mines. Several estimation methods had been established for the coal mine methane (CMM) emission. However, with large regional differences, various reservoir formation types of coalbed methane (CBM) and due to the complicated geological conditions in China, these methods may be deficient or unsuitable for all the mining areas (e.g. Jiaozuo mining area). By combing the CMM emission characteristics and considering the actual situation of methane emissions from underground coal mine, we found that the methane pre-drainage is a crucial reason creating inaccurate evaluating results for most estimation methods. What makes it so essential is the extensive pre-drainage quantity and its irrelevance with annual coal production. Accordingly, the methane releases were divided into two categories: methane pre-drainage and methane release during mining. On this basis, a pioneering method for estimating CMM emissions was proposed. Taking the Yanma coal mine in the Jiaozuo mining area as a study case, the evaluation method of the pre-drainage methane quantity was established after the correlation analysis between the pre-drainage rate and time. Thereafter, the mining activity influence factor (MAIF) was first introduced to reflect the methane release from the coal and rock seams around where affected by mining activity, and the buried depth was adopted as the predictor of the estimation for future methane emissions. It was verified in the six coal mines of Jiaozuo coalfield (2011) that the new estimation method has the minimum errors of 12.11%, 9.23%, 5.77%, -5.20%, -8.75% and 4.92% respectively comparing with other methods. This paper gives a further insight and proposes a more accurate evaluation method for the CMM emissions, especially for the coal seams with low permeability and strong tectonic deformation in methane outburst coal mines.

  14. Productivity Improvement in Underground Coal Mines - A Case Study

    Directory of Open Access Journals (Sweden)

    Devi Prasad Mishra

    2013-01-01

    Full Text Available Improvement of productivity has become an important goal for today's coal industry in the race to increase price competitiveness. The challenge now lying ahead for the coal industry is to identify areas of waste, meet the market price and maintain a healthy profit. The only way to achieve this is to reduce production costs by improving productivity, efficiency and the effectiveness of the equipment. This paper aims to identify the various factors and problems affecting the productivity of underground coal mines adopting the bord and pillar method of mining and to propose suitable measures for improving them. The various key factors affecting productivity, namely the cycle of operations, manpower deployment, machine efficiency, material handling and management of manpower are discussed. In addition, the problem of side discharge loader (SDL cable handling resulting in the wastage of precious manpower resources and SDL breakdown have also been identified and resolved in this paper.

  15. Underground coal mining - methods, equipment developments and trends

    Energy Technology Data Exchange (ETDEWEB)

    Singhal, R

    1988-12-01

    Underground mines are truly beginning to accept the so-called 'high tech' technology evident in other industries. Automation, remote control and robotics have taken an added significance. Wireless communication, mine-wide equipment health and performance monitoring, and transmission of data from deeper levels to surface is moving towards becoming the norm. There is emphasis on developing and applying continuous mining systems, as well as on modifying cyclical discontinuous methods to continuous systems. Multi-purpose equipment is also being developed. Technology transfer is playing its role - equipment and systems from surface coal mining are being applied to underground mining and vice-versa. At the American Mining Congress Exhibition held in Chicago in April 1988, a variety of equipment for underground mining was displayed including coal face equipment such as shearer loaders, conveyors and powered supports, and equipment for room-and-pillar coal mining. The trend continues to be towards high power machines equipped with a variety of electronics and sensors, safety devices, and alarm systems. Ancillary equipment on display covered a variety of cutting drums, cutting tools, conveying equipment and so on. In room-and-pillar mining, the overall emphasis was on moving away from the cyclical nature of the work. Transportation by shuttle cars must be replaced by continuous transport systems such as conveyors. Experience from Australia has shown that the application of continuous haulage and breaker line supports has permitted a doubling of production from room-and-pillar systems. Production levels of 3,000tpd have already been achieved, and 4,000tpd is considered achievable.

  16. 75 FR 17529 - High-Voltage Continuous Mining Machine Standard for Underground Coal Mines

    Science.gov (United States)

    2010-04-06

    ... High-Voltage Continuous Mining Machine Standard for Underground Coal Mines AGENCY: Mine Safety and... of high-voltage continuous mining machines in underground coal mines. It also revises MSHA's design...-- Underground Coal Mines III. Section-by-Section Analysis A. Part 18--Electric Motor-Driven Mine Equipment and...

  17. 77 FR 58170 - Proposed Renewal of Existing Information Collection; Fire Protection (Underground Coal Mines)

    Science.gov (United States)

    2012-09-19

    ... Renewal of Existing Information Collection; Fire Protection (Underground Coal Mines) AGENCY: Mine Safety... INFORMATION: I. Background Fire protection standards for underground coal mines are based on section 311(a) of the Federal Mine Safety and Health Act of 1977 (Mine Act). 30 CFR 75.1100 requires that each coal mine...

  18. Performance of underground coal mines during the 1976 Tangshan earthquake

    Energy Technology Data Exchange (ETDEWEB)

    Lee, C.F.

    1987-01-01

    The Tangshan earthquake of 1976 costs 242 000 lives and was responsible for 164 000 serious injuries and structural damage of immense proportion. The area has eight coal mines, which together form the largest underground coal mining operation in China. Approximately 10 000 miners were working underground at the time of the earthquake. With few exceptions they survived and returned safely to the surface, only to find their families and belongings largely destroyed. Based on a comprehensive survey of the miners' observations, subsurface intensity profiles were drawn up. The profiles clearly indicated that seismic damage in the underground mines was far less severe than at the surface. 16 refs., 4 figs., 2 tabs.

  19. Is there a risk to safety when working in the New South Wales underground coal-mining industry while having binaural noise-induced hearing loss?

    Energy Technology Data Exchange (ETDEWEB)

    Viljoen, D.A.; Nie, V.; Guest, M. [University of Newcastle, Newcastle, NSW (Australia)

    2006-03-15

    This study is designed to investigate the possible association between hearing loss and accidents in the New South Wales underground coal-mining industry. The study was conducted, gathering data over a 10-year period from 1994 to 2003, which identified 97 cases that have had accidents and 983 controls that have had no accidents. Hearing loss levels were noted and compared in the cases and controls. Multiple logistic regression was used to determine whether the variables were significant risk factors in the occurrence of accidents. Hearing loss levels in the total cohort varied from 0 to 54%. The proportion of cases with hearing loss appeared to be significantly higher in the young age group of {lt} 29 years than in the controls, but was not significantly different in the older age groups. This study indicates that workers who have lost up to 54% binaural high tone hearing and are older than 29 years do not appear to have an increased risk to safety when compared with workers who do not have hearing loss. However, workers in the young age group of {lt} 29 years who have high tone hearing loss may be at an increased risk of accident.

  20. Ground engineering principles and practices for underground coal mining

    CERN Document Server

    Galvin, J M

    2016-01-01

    This book teaches readers ground engineering principles and related mining and risk management practices associated with underground coal mining. It establishes the basic elements of risk management and the fundamental principles of ground behaviour and then applies these to the essential building blocks of any underground coal mining system, comprising excavations, pillars, and interactions between workings. Readers will also learn about types of ground support and reinforcement systems and their operating mechanisms. These elements provide the platform whereby the principles can be applied to mining practice and risk management, directed primarily to bord and pillar mining, pillar extraction, longwall mining, sub-surface and surface subsidence, and operational hazards. The text concludes by presenting the framework of risk-based ground control management systems for achieving safe workplaces and efficient mining operations. In addition, a comprehensive reference list provides additional sources of informati...

  1. Improving underground ventilation conditions in coal mines

    CSIR Research Space (South Africa)

    Meyer, CF

    1993-11-01

    Full Text Available projects could be initiated by miningtek in co-operation with different mines. This report deals with the findings of this project and also deals with the future of research within Miningtek with regard to underground ventilation....

  2. VRLane: a desktop virtual safety management program for underground coal mine

    Science.gov (United States)

    Li, Mei; Chen, Jingzhu; Xiong, Wei; Zhang, Pengpeng; Wu, Daozheng

    2008-10-01

    VR technologies, which generate immersive, interactive, and three-dimensional (3D) environments, are seldom applied to coal mine safety work management. In this paper, a new method that combined the VR technologies with underground mine safety management system was explored. A desktop virtual safety management program for underground coal mine, called VRLane, was developed. The paper mainly concerned about the current research advance in VR, system design, key techniques and system application. Two important techniques were introduced in the paper. Firstly, an algorithm was designed and implemented, with which the 3D laneway models and equipment models can be built on the basis of the latest mine 2D drawings automatically, whereas common VR programs established 3D environment by using 3DS Max or the other 3D modeling software packages with which laneway models were built manually and laboriously. Secondly, VRLane realized system integration with underground industrial automation. VRLane not only described a realistic 3D laneway environment, but also described the status of the coal mining, with functions of displaying the run states and related parameters of equipment, per-alarming the abnormal mining events, and animating mine cars, mine workers, or long-wall shearers. The system, with advantages of cheap, dynamic, easy to maintenance, provided a useful tool for safety production management in coal mine.

  3. Data Mining Mining Data: MSHA Enforcement Efforts, Underground Coal Mine Safety, and New Health Policy Implications

    OpenAIRE

    Thomas J. Kniesner; John D. Leeth

    2003-01-01

    Studies of industrial safety regulations, Occupational Safety and Health Administration (OSHA) in particular, often find little effect on worker safety. Critics of the regulatory approach argue that safety standards have little to do with industrial injuries and defenders of the regulatory approach cite infrequent inspections and low fines for violating safety standards. We use recently assembled data from the Mine Safety and Health Administration (MSHA) concerning underground coal mine produ...

  4. Data Mining Mining Data: MSHA Enforcement Efforts, Underground Coal Mine Safety, and New Health Implications

    OpenAIRE

    Kniesner, Thomas J.; Leeth, John D.

    2003-01-01

    Studies of industrial safety regulations, OSHA in particular, often find little effect on worker safety. Critics of the regulatory approach argue that safety standards have little to do with industrial injuries, and defenders of the regulatory approach cite infrequent inspections and low penalties for violating safety standards. We use recently assembled data from the Mine Safety and Health Administration (MSHA) concerning underground coal mine production, safety regulatory activities, and wo...

  5. 76 FR 70075 - Proximity Detection Systems for Continuous Mining Machines in Underground Coal Mines

    Science.gov (United States)

    2011-11-10

    ... Detection Systems for Continuous Mining Machines in Underground Coal Mines AGENCY: Mine Safety and Health... proposed rule addressing Proximity Detection Systems for Continuous Mining Machines in Underground Coal... Detection Systems for Continuous Mining Machines in Underground Coal Mines. MSHA conducted hearings on...

  6. Damage to underground coal mines caused by surface blasting

    International Nuclear Information System (INIS)

    Fourie, A.B.; Green, R.W.

    1993-01-01

    An investigation of the potential damage to underground coal workings as a result of surface blasting at an opencast coal mine is described. Seismometers were installed in a worked out area of an underground mine, in the eastern Transvaal region of South Africa, and the vibration caused by nearby surface blasting recorded. These measurements were used to derive peak particle velocities. These velocities were correlated with observed damage underground in order to establish the allowable combination of the two blasting parameters of charge mass per relay, and blast-to-gage point distance. An upper limit of 110mm/sec peak particle velocity was found to be sufficient to ensure that the damage to the particular workings under consideration was minimal. It was further found that a cube-root scaling law provided a better fit to the field data than the common square-root law. 11 refs., 6 figs., 5 tabs

  7. 76 FR 63238 - Proximity Detection Systems for Continuous Mining Machines in Underground Coal Mines

    Science.gov (United States)

    2011-10-12

    ... Detection Systems for Continuous Mining Machines in Underground Coal Mines AGENCY: Mine Safety and Health... Agency's proposed rule addressing Proximity Detection Systems for Continuous Mining Machines in... proposed rule for Proximity Detection Systems on Continuous Mining Machines in Underground Coal Mines. Due...

  8. 76 FR 54163 - Proximity Detection Systems for Continuous Mining Machines in Underground Coal Mines

    Science.gov (United States)

    2011-08-31

    ... Detection Systems for Continuous Mining Machines in Underground Coal Mines AGENCY: Mine Safety and Health... (except full-face continuous mining machines) with proximity detection systems. Miners working near..., each underground coal mine operator would be required to install proximity detection systems on...

  9. Shale Failure Mechanics and Intervention Measures in Underground Coal Mines: Results From 50 Years of Ground Control Safety Research

    Science.gov (United States)

    2015-01-01

    Ground control research in underground coal mines has been ongoing for over 50 years. One of the most problematic issues in underground coal mines is roof failures associated with weak shale. This paper will present a historical narrative on the research the National Institute for Occupational Safety and Health has conducted in relation to rock mechanics and shale. This paper begins by first discussing how shale is classified in relation to coal mining. Characterizing and planning for weak roof sequences is an important step in developing an engineering solution to prevent roof failures. Next, the failure mechanics associated with the weak characteristics of shale will be discussed. Understanding these failure mechanics also aids in applying the correct engineering solutions. The various solutions that have been implemented in the underground coal mining industry to control the different modes of failure will be summarized. Finally, a discussion on current and future research relating to rock mechanics and shale is presented. The overall goal of the paper is to share the collective ground control experience of controlling roof structures dominated by shale rock in underground coal mining. PMID:26549926

  10. Possibilities of professional career in the German coal mining industry

    Energy Technology Data Exchange (ETDEWEB)

    Gierhardt, H; Mader, S

    1977-06-01

    Development and age structure of the labor force. Possibilities and courses of professional training in the German coal mining industry. Choice of profession and possibilities of promotion. More advertising campaigns necessary to obtain recruits for mining work.

  11. Management of mining-related damages in abandoned underground coal mine areas using GIS

    International Nuclear Information System (INIS)

    Lee, U.J.; Kim, J.A.; Kim, S.S.; Kim, W.K.; Yoon, S.H.; Choi, J.K.

    2005-01-01

    The mining-related damages such as ground subsidence, acid mine drainage (AMD), and deforestation in the abandoned underground coal mine areas become an object of public concern. Therefore, the system to manage the mining-related damages is needed for the effective drive of rehabilitation activities. The management system for Abandoned Underground Coal Mine using GIS includes the database about mining record and information associated with the mining-related damages and application programs to support mine damage prevention business. Also, this system would support decision-making policy for rehabilitation and provide basic geological data for regional construction works in abandoned underground coal mine areas. (authors)

  12. Underground coal mine subsidence impacts on surface water

    International Nuclear Information System (INIS)

    Stump, D.E. Jr.

    1992-01-01

    This paper reports that subsidence from underground coal mining alters surface water discharge and availability. The magnitude and areal extent of these impacts are dependent on many factors, including the amount of subsidence, topography, geology, climate, surface water - ground water interactions, and fractures in the overburden. There alterations may have positive and/or negative impacts. One of the most significant surface water impacts occurred in July 1957 near West Pittston, Pennsylvania. Subsidence in the Knox Mine under the Coxton Yards of the Lehigh Valley Railroad allowed part of the discharge in the Susquehanna River to flow into the mine and create a crater 200 feet in diameter and 300 feet deep. Fourteen railroad gondola cars fell into the hole which was eventually filled with rock, sand, and gravel. Other surface water impacts from subsidence may include the loss of water to the ground water system, the gaining of water from the ground water system, the creation of flooded subsidence troughs, the increasing of impoundment storage capacity, the relocation of water sources (springs), and the alteration of surface drainage patterns

  13. Booster fans : some considerations for their usage in underground coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Gillies, S.; Slaughter, C. [Missouri Univ. of Science and Technology, Rolla, MO (United States); Calizaya, F. [Utah Univ., Salt Lake City, UT (United States); Wu, H.W. [Gillies Wu Mining Technology Pty Ltd., Brisbane, QLD (Australia)

    2010-07-01

    This paper reported on a study that investigated the conditions under which booster fans can be used safely and efficiently in underground coal mines. Booster fans are installed in series with a main surface fan and are used to boost the air pressure of the ventilation air passing through it. Several coal mining countries use booster fans, but in the United States, they are only used in metal/non-metal mines due to concerns of uncontrolled recirculation. This study investigated installations of booster fans in non-US underground coal mines where safe and efficient atmospheric conditions are achieved. The purpose was to collect reliable information on airway resistances and flow requirements typical in large US coal mines. The study showed that safe booster fan installations are found in both high and low gas conditions, and sometimes where workings are located at great depths. The interlocking systems within the booster fan can control the underground fans and avoid recirculation when surface fans are unexpectedly turned off. Another purpose of the study was to determine when booster fans become a more viable solution in coal mines due to increases in air requirements at higher production rates. It was concluded that a new fan selection algorithm to produce recirculation-free ventilation designs will be developed to enable US coal mine operators to develop ventilation designs to extract coal seams from depths greater than 1000 m. 17 refs., 1 fig.

  14. Influence of surface water accumulations of the Stupnica creek on underground coal mining in the Durdevic coal mine

    Energy Technology Data Exchange (ETDEWEB)

    Valjarevic, R; Urosevic, V

    1986-01-01

    Discusses hydrological, geological and mining conditions at the Durdevic underground coal mine. A landslide at a spoil bank dammed the creek flowing above the mine. Two exploratory boreholes (62 m and 68 m) were drilled for hydrological investigations. Water coloring techniques, chemical water analysis, measurement of underground water level and water flow were used to determine whether a sudden inrush of rainfall and accumulated surface water could endanger the mine. Underground water inflow to mine rooms varies from 110-200 m/sup 3//min, depending on the season. Diversion of the creek bed with the accumulated water and accumulation and subsequent drainage of surface water via large diameter concrete pipes were considered as possible ways of improving safety in the mine. Details of these projects are included. 4 refs.

  15. Thermal load at workstations in the underground coal mining: Results of research carried out in 6 coal mines

    Directory of Open Access Journals (Sweden)

    Krzysztof Słota

    2016-08-01

    Full Text Available Background: Statistics shows that almost half of Polish extraction in underground mines takes place at workstations where temperature exceeds 28°C. The number of employees working in such conditions is gradually increasing, therefore, the problem of safety and health protection is still growing. Material and Methods: In the present study we assessed the heat load of employees at different workstations in the mining industry, taking into account current thermal conditions and work costs. The evaluation of energy cost of work was carried out in 6 coal mines. A total of 221 miners employed at different workstations were assessed. Individual groups of miners were characterized and thermal safety of the miners was assessed relying on thermal discomfort index. Results: The results of this study indicate considerable differences in the durations of analyzed work processes at individual workstations. The highest average energy cost was noted during the work performed in the forehead. The lowest value was found in the auxiliary staff. The calculated index of discomfort clearly indicated numerous situations in which the admissible range of thermal load exceeded the parameters of thermal load safe for human health. It should be noted that the values of average labor cost fall within the upper, albeit admissible, limits of thermal load. Conclusions: The results of the study indicate that in some cases work in mining is performed in conditions of thermal discomfort. Due to high variability and complexity of work conditions it becomes necessary to verify the workers’ load at different workstations, which largely depends on the environmental conditions and work organization, as well as on the performance of workers themselves. Med Pr 2016;67(4:477–498

  16. 76 FR 11187 - Examinations of Work Areas in Underground Coal Mines for Violations of Mandatory Health or Safety...

    Science.gov (United States)

    2011-03-01

    ... DEPARTMENT OF LABOR Mine Safety and Health Administration 30 CFR Part 75 RIN 1219-AB75 Examinations of Work Areas in Underground Coal Mines for Violations of Mandatory Health or Safety Standards... rule addressing Examinations of Work Areas in Underground Coal Mines for Violations of Mandatory Health...

  17. Application and Development of an Environmentally Friendly Blast Hole Plug for Underground Coal Mines

    Directory of Open Access Journals (Sweden)

    Donghui Yang

    2018-01-01

    Full Text Available Drilling and blasting technology is one of the main methods for pressure relief in deep mining. The traditional method for blasting hole blockage with clay stemming has many problems, which include a large volume of transportation, excess loading time, and high labor intensity. An environmentally friendly blast hole plug was designed and developed. This method is cheap, closely blocks the hole, is quickly loaded, and is convenient for transportation. The impact test on the plug was carried out using an improved split Hopkinson pressure bar test system, and the industrial test was carried out in underground tunnel of coal mine. The tests results showed that, compared with clay stemming, the new method proposed in this paper could prolong the action time of the detonation gas, prevent premature detonation gas emissions, reduce the unit consumption of explosives, improve the utilization ratio, reduce the labor intensity of workers, and improve the effect of rock blasting with low cost of rock breaking.

  18. Groundwater-quality data associated with abandoned underground coal mine aquifers in West Virginia, 1973-2016: Compilation of existing data from multiple sources

    Science.gov (United States)

    McAdoo, Mitchell A.; Kozar, Mark D.

    2017-11-14

    This report describes a compilation of existing water-quality data associated with groundwater resources originating from abandoned underground coal mines in West Virginia. Data were compiled from multiple sources for the purpose of understanding the suitability of groundwater from abandoned underground coal mines for public supply, industrial, agricultural, and other uses. This compilation includes data collected for multiple individual studies conducted from July 13, 1973 through September 7, 2016. Analytical methods varied by the time period of data collection and requirements of the independent studies.This project identified 770 water-quality samples from 294 sites that could be attributed to abandoned underground coal mine aquifers originating from multiple coal seams in West Virginia.

  19. 77 FR 25205 - Proposed Extension of Existing Information Collection; Roof Control Plans for Underground Coal Mines

    Science.gov (United States)

    2012-04-27

    ... collections of information in accordance with the Paperwork Reduction Act of 1995. This program helps to assure that requested data can be provided in the desired format, reporting burden (time and financial... Information Collection; Roof Control Plans for Underground Coal Mines AGENCY: Mine Safety and Health...

  20. 75 FR 57849 - Maintenance of Incombustible Content of Rock Dust in Underground Coal Mines

    Science.gov (United States)

    2010-09-23

    ... correlation between higher job risk and higher wages, suggesting that employees demand monetary compensation... DEPARTMENT OF LABOR Mine Safety and Health Administration 30 CFR Part 75 RIN 1219-AB76 Maintenance of Incombustible Content of Rock Dust in Underground Coal Mines AGENCY: Mine Safety and Health...

  1. 75 FR 20918 - High-Voltage Continuous Mining Machine Standard for Underground Coal Mines

    Science.gov (United States)

    2010-04-22

    ... DEPARTMENT OF LABOR Mine Safety and Health Administration 30 CFR Parts 18 and 75 RIN 1219-AB34 High-Voltage Continuous Mining Machine Standard for Underground Coal Mines Correction In rule document 2010-7309 beginning on page 17529 in the issue of Tuesday, April 6, 2010, make the following correction...

  2. A Wireless LAN and Voice Information System for Underground Coal Mine

    Directory of Open Access Journals (Sweden)

    Yu Zhang

    2014-06-01

    Full Text Available In this paper we constructed a wireless information system, and developed a wireless voice communication subsystem based on Wireless Local Area Networks (WLAN for underground coal mine, which employs Voice over IP (VoIP technology and Session Initiation Protocol (SIP to achieve wireless voice dispatching communications. The master control voice dispatching interface and call terminal software are also developed on the WLAN ground server side to manage and implement the voice dispatching communication. A testing system for voice communication was constructed in tunnels of an underground coal mine, which was used to actually test the wireless voice communication subsystem via a network analysis tool, named Clear Sight Analyzer. In tests, the actual flow charts of registration, call establishment and call removal were analyzed by capturing call signaling of SIP terminals, and the key performance indicators were evaluated in coal mine, including average subjective value of voice quality, packet loss rate, delay jitter, disorder packet transmission and end-to- end delay. Experimental results and analysis demonstrate that the wireless voice communication subsystem developed communicates well in underground coal mine environment, achieving the designed function of voice dispatching communication.

  3. Development of a fire detector for underground coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Hemingway, M.A.; Walsh, P.T.; Hunneyball, S.R.; Williams, M.; Jobling, S.; Pell, B.; West, N.G. [Health and Safety Laboratory, Buxton (United Kingdom)

    2005-07-01

    Current fire detectors in use in UK coal mines, based on semiconductor sensors which detect gaseous products of combustion, are under-utilised, are not user-friendly, have performance limitations due to interferences and are obsolete. A joint research project was therefore instigated to develop an improved fire detector. This paper describes tests performed in an experimental mine roadway on various types of sensor. The sensors were exposed to smouldering conveyor belt, coal, wood, oil and grease, and diesel exhaust fume. A potential advanced detector is based on the combination of blue and infrared optical smoke sensors which distinguish fires and diesel exhaust from coal dust, nitric oxide or nitrogen dioxide sensors to distinguish smoulderi8ng fires form diesel exhaust, and carbon monoxide sensors for general body monitoring. 6 refs., 5 figs.

  4. Estimating Limits for the Geothermal Energy Potential of Abandoned Underground Coal Mines: A Simple Methodology

    Directory of Open Access Journals (Sweden)

    Rafael Rodríguez Díez

    2014-07-01

    Full Text Available Flooded mine workings have good potential as low-enthalpy geothermal resources, which could be used for heating and cooling purposes, thus making use of the mines long after mining activity itself ceases. It would be useful to estimate the scale of the geothermal potential represented by abandoned and flooded underground mines in Europe. From a few practical considerations, a procedure has been developed for assessing the geothermal energy potential of abandoned underground coal mines, as well as for quantifying the reduction in CO2 emissions associated with using the mines instead of conventional heating/cooling technologies. On this basis the authors have been able to estimate that the geothermal energy available from underground coal mines in Europe is on the order of several thousand megawatts thermal. Although this is a gross value, it can be considered a minimum, which in itself vindicates all efforts to investigate harnessing it.

  5. The Increase of Power Efficiency of Underground Coal Mining by the Forecasting of Electric Power Consumption

    Science.gov (United States)

    Efremenko, Vladimir; Belyaevsky, Roman; Skrebneva, Evgeniya

    2017-11-01

    In article the analysis of electric power consumption and problems of power saving on coal mines are considered. Nowadays the share of conditionally constant costs of electric power for providing safe working conditions underground on coal mines is big. Therefore, the power efficiency of underground coal mining depends on electric power expense of the main technological processes and size of conditionally constant costs. The important direction of increase of power efficiency of coal mining is forecasting of a power consumption and monitoring of electric power expense. One of the main approaches to reducing of electric power costs is increase in accuracy of the enterprise demand in the wholesale electric power market. It is offered to use artificial neural networks to forecasting of day-ahead power consumption with hourly breakdown. At the same time use of neural and indistinct (hybrid) systems on the principles of fuzzy logic, neural networks and genetic algorithms is more preferable. This model allows to do exact short-term forecasts at a small array of input data. A set of the input parameters characterizing mining-and-geological and technological features of the enterprise is offered.

  6. A Fiber Bragg Grating-Based Monitoring System for Roof Safety Control in Underground Coal Mining

    Directory of Open Access Journals (Sweden)

    Yiming Zhao

    2016-10-01

    Full Text Available Monitoring of roof activity is a primary measure adopted in the prevention of roof collapse accidents and functions to optimize and support the design of roadways in underground coalmines. However, traditional monitoring measures, such as using mechanical extensometers or electronic gauges, either require arduous underground labor or cannot function properly in the harsh underground environment. Therefore, in this paper, in order to break through this technological barrier, a novel monitoring system for roof safety control in underground coal mining, using fiber Bragg grating (FBG material as a perceived element and transmission medium, has been developed. Compared with traditional monitoring equipment, the developed, novel monitoring system has the advantages of providing accurate, reliable, and continuous online monitoring of roof activities in underground coal mining. This is expected to further enable the prevention of catastrophic roof collapse accidents. The system has been successfully implemented at a deep hazardous roadway in Zhuji Coal Mine, China. Monitoring results from the study site have demonstrated the advantages of FBG-based sensors over traditional monitoring approaches. The dynamic impacts of progressive face advance on roof displacement and stress have been accurately captured by the novel roadway roof activity and safety monitoring system, which provided essential references for roadway support and design of the mine.

  7. Development of mechanization of extraction in underground coal mining (part I)

    Energy Technology Data Exchange (ETDEWEB)

    Strzeminski, J

    1984-01-01

    The history of underground coal mining and history of mechanizing underground operations of cutting, strata control, mine haulage, hoisting and ventilation are discussed. The following development periods are characterized: until 1769 (date of steam engine invention by J. Watt), from 1769 to 1945 (period of partial mechanization of operations in underground coal mining), from 1945 (period of comprehensive mechanization and automation). A general description of mining in the first development period is given. Evaluation of the second development period concentrates on mechanization in underground coal mining. The following equipment types are described: cutting (pneumatic picks and pneumatic drills, coal saws developed by Eickhoff, coal cutters developed after 1870, cutter loaders patented in 1925-1927, coal plows and coal cutter loaders), mine haulage (mine cars, conveyors developed in the United Kingdom, Germany and Russia, Poland), strata control at working faces (timber props, steel friction props, roof bars), strata control in the goaf (room and pillar mining, stowing, minestone utilization for stowing in Upper Silesia, hydraulic stowing in Upper Silesia). 5 references.

  8. A Wireless LAN and Voice Information System for Underground Coal Mine

    OpenAIRE

    Yu Zhang; Wei Yang; Dongsheng Han; Young-Il Kim

    2014-01-01

    In this paper we constructed a wireless information system, and developed a wireless voice communication subsystem based on Wireless Local Area Networks (WLAN) for underground coal mine, which employs Voice over IP (VoIP) technology and Session Initiation Protocol (SIP) to achieve wireless voice dispatching communications. The master control voice dispatching interface and call terminal software are also developed on the WLAN ground server side to manage and implement the voice dispatching co...

  9. New on-board extinguisher system on diesel-driven vehicles in the German underground coal mining industry; Neuartige bordfeste Loeschanlage auf dieselgetriebenen Fahrzeugen im untertaegigen deutschen Steinkohlenbergbau

    Energy Technology Data Exchange (ETDEWEB)

    Fetting, Dieter; Alze, Matthias [Bergwerk Ost, Hamm (Germany); Cerny, Udo [RAG Deutsche Steinkohle AG, Herne (Germany). Hauptstelle fuer das Grubenrettungswesen

    2010-01-15

    A new extinguisher system has been developed by protectfire Brandschutztechnik GmbH and has now been approved for use in underground mines. This extinguisher system is interesting by virtue of its reliability (no faulty tripping e.g. by defective electrical components is possible) and it's extinguishing efficiency (significantly longer extinguishing time compared to a powder extinguisher). No outside energy source is required for operation of the extinguisher. The motor is stopped more quickly by connection of the motor shutdown valve in the exciter line. Economic considerations - easier maintenance and lower costs compared to similar systems - also make this system interesting. (orig.)

  10. State-of-the-art study of resource characterization and planning for underground coal mining. Final technical report as of June 30, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Walton, D.; Ingham, W.; Kauffman, P.

    1980-06-01

    With the rapid developments taking place in coal mining technology and due to high investment costs, optimization of the structure of underground coal mines is crucial to the success of the mining project. The structure of a mine, once it is developed, cannot be readily changed and has a decisive influence on the productivity, safety, economics, and production capacity of the mine. The Department of Energy desires to ensure that the resource characterization and planning activity for underground coal mining will focus on those areas that offer the most promise of being advanced. Thus, this project was undertaken by Management Engineers Incorporated to determine the status in all aspects of the resource characterization and planning activities for underground coal mining as presently performed in the industry. The study team conducted a comprehensive computerized literature search and reviewed the results. From this a selection of the particularly relevant sources were annotated and a reference list was prepared, catalogued by resource characterization and mine planning activity. From this data, and discussions with industry representatives, academia, and research groups, private and federal, an assessment and evaluation was made of the state-of-the-art of each element in the resource characterization and mine planning process. The results of this analysis lead to the identifcation of areas requiring research and, specifically, those areas where DOE research efforts may be focused.

  11. A Look into Miners' Health in Prevailing Ambience of Underground Coal Mine Environment

    Science.gov (United States)

    Dey, N. C.; Pal, S.

    2012-04-01

    Environmental factors such as noise, vibration, illumination, humidity, temperature and air velocity, etc. do play a major role on the health, comfort and efficient performance of underground coal miners at work. Ergonomics can help to promote health, efficiency and well being of miners and to make best use of their capabilities within the ambit of underground coal mine environment. Adequate work stretch and work-rest scheduling have to be determined for every category of miners from work physiology point of view so as to keep better health of the miners in general and to have their maximum efficiency at work in particular.

  12. Possible strategies in development of highly productive underground coal mining

    Energy Technology Data Exchange (ETDEWEB)

    Djoric, M

    1980-01-01

    This paper explains the basic strategies which may be applied in the exploitation of coal deposits by underground mining. It outlines the importance of combinations of extensive (non-mechanized) and intensive (mechanized) exploitation and their dependence on coal demand, available financial means, requirements concerning the protection of environment, unemployment of the population, availability of mechanical and electrical equipment, technical staff, etc. It is suggested that the applied strategy be revised and adapted to the current situation. Postponement of exploitation until the future when the demand and price of coal may be higher is criticized. The possibility of applying extensive underground mining in areas where unemployment and lack of capital speak against the application of fully mechanized working methods is also dealt with. (In Serbo-Croatian)

  13. Continuous dust monitoring in headings in underground coal mines

    Directory of Open Access Journals (Sweden)

    Kazimierz Lebecki

    2016-01-01

    Full Text Available The article presents hazardous conditions of airborne dust based on the results of measurements of dust concentration taken at work-places at a underground rock-coal face drilled by a heading machine with combined ventilation (suction and forced ventilation with dust collector. The measurements were taken using three methods in order to examine and assess the actual conditions within the excavation subject to the study. The measurement results and conclusions show major difficulties in achieving MAC levels. Research conclusions indicate the low efficiency of collective and personal measures applied to protect against dust harmful to health as well as the need to improve them.

  14. Reducing rock fall injuries in underground US coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, S.B.; Molinda, G.M.; Pappas, D.M. [Pittsburgh Research Laboratory, Pittsburgh, PA (United States)

    2005-07-01

    A continuing risk to underground US coal miners is rock falling from the mine roof. Almost 99% of injuries caused by rock falls are not from a major roof collapse, but from smaller rock that fall from between roof bolts. Installing roof screen provides excellent overhead roof coverage and dramatically reduces the potential for rock fall injuries, especially to roof bolted operators. The National Institute for Occupational Safety and Health (NIOSH) has explored different installation techniques and roof screening options along with machine design innovations that make roof screening easier and safer. Applying ergonomic principles to roof screening will offer insight and direction for better material handling. Other techniques for controlling rock falls and roof falls for long-term stability include the application of surface support liners and polyurethane (PUR) injection. An ongoing study at the NIOSH Lake Lynn Laboratory of various types of spray-on liner and shotcrete materials is providing a unique opportunity to evaluate the long-term behaviour of liners in an underground environment. In-mine studies of PUR have involved pre- and post-injection core drilling and video borecole logging. The results have provided insights into how PUR penetrates and reinforces weak and highly fractured rock. 11 refs., 8 figs., 1 tab.

  15. An integrated environment monitoring system for underground coal mines--Wireless Sensor Network subsystem with multi-parameter monitoring.

    Science.gov (United States)

    Zhang, Yu; Yang, Wei; Han, Dongsheng; Kim, Young-Il

    2014-07-21

    Environment monitoring is important for the safety of underground coal mine production, and it is also an important application of Wireless Sensor Networks (WSNs). We put forward an integrated environment monitoring system for underground coal mine, which uses the existing Cable Monitoring System (CMS) as the main body and the WSN with multi-parameter monitoring as the supplementary technique. As CMS techniques are mature, this paper mainly focuses on the WSN and the interconnection between the WSN and the CMS. In order to implement the WSN for underground coal mines, two work modes are designed: periodic inspection and interrupt service; the relevant supporting technologies, such as routing mechanism, collision avoidance, data aggregation, interconnection with the CMS, etc., are proposed and analyzed. As WSN nodes are limited in energy supply, calculation and processing power, an integrated network management scheme is designed in four aspects, i.e., topology management, location management, energy management and fault management. Experiments were carried out both in a laboratory and in a real underground coal mine. The test results indicate that the proposed integrated environment monitoring system for underground coal mines is feasible and all designs performed well as expected.

  16. Task rotation in an underground coal mine: A pilot study.

    Science.gov (United States)

    Jones, Olivia F; James, Carole L

    2018-01-01

    Task rotation is used to decrease the risk of workplace injuries and improve work satisfaction. To investigate the feasibility, benefits and challenges of implementing a task rotation schedule within an underground coalmine in NSW, Australia. A mixed method case control pilot study with the development and implementation of a task rotation schedule for 6 months with two work crews. A questionnaire including The Nordic Musculoskeletal Questionnaire, The Need for Recovery after Work Scale, and The Australian WHOQOL- BREF Australian Edition was used to survey workers at baseline, 3 and 6 months. A focus group was completed with the intervention crew and management at the completion of the study. In total, twenty-seven participants completed the survey. Significant improvements in the psychological and environmental domains of the WHOQOL-BREF questionnaire were found in the intervention crew. Musculoskeletal pain was highest in the elbow, lower back and knee, and fatigue scores improved, across both groups. The intervention crew felt 'mentally fresher', 'didn't do the same task twice in a row', and 'had more task variety which made the shift go quickly'. Task rotation was positively regarded, with psychological benefits identified. Three rotations during a 9-hour shift were feasible and practical in this environment.

  17. Absenteeism and accidents in a dangerous environment: empirical analysis of underground coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Goodman, P.S.; Garber, S.

    1988-02-01

    The study examined the effects or consequences of absenteeism on accidents. Data were gathered from production crews in five underground coal mines. A unique data set was created that traced on a daily basis the absence event, the company's policy on replacement, and the occurrence of an accident. The concept of familiarity was introduced to explain the impact of absenteeism on accidents. The basic data showed that absenteeism increased the chances for accidents in certain categories of unfamiliarity. Implications for manpower policy and absentee research are discussed. 4 tabs., 6 refs.

  18. Remote control of safety and technological mining processes in underground coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Marjanovic, D. (Elektronska Industrija RO IRI OOUR Razvoj, Nis (Yugoslavia))

    1989-02-01

    Discusses importance of data relevant to remote monitoring of production and safety at work in underground coal mines. The EI PS 2000 multi-purpose system developed by Elektronska Industrija, Nis, for use with AP-X1 and AP-X2 microcomputers in Serbian mines is described. Component parts include the CUM-8 central unit, the CIP-8 communication interface processor, the SNM-64 disjunction unit, the NM-64 energy supply unit and the CRT alarm monitor. This system is designed to warn of mine fires, methane and coal dust explosions, to help in evacuating mine crews, to control production processes and mine management and other functions. 8 refs

  19. Study on the Effect of Frequency on Conductivity of Underground Strata in Coal Mine Through-the-earth Wireless Communication

    Directory of Open Access Journals (Sweden)

    Jinyi TAO

    2014-09-01

    Full Text Available The relationship of conductivity and the frequency, which is of decisive significance in through-the-earth wireless communication in coal mine, is closely related to the options of frequency range in coal mine wireless communication. When through-the-earth wireless communication is applied, the electromagnetic waves need to spread in the semi-conductive medium rocks. The main factors affecting the electromagnetic wave propagation in rocks is the rock strata electromagnetic parameters. These parameters are magnetic permeability m (H/m, dielectric constant e (F/m and electrical conductivity s (S/m. In these parameters, electrical conductivity is not constant. Under the influence of various factors, it will be great changes. This paper, for the specific circumstances of coal mine rock, discuses and conduct dada mining the effect frequency on the electrical conductivity of underground rock in coal mine with through-the-earth wireless communication.

  20. A Review of Mine Rescue Ensembles for Underground Coal Mining in the United States.

    Science.gov (United States)

    Kilinc, F Selcen; Monaghan, William D; Powell, Jeffrey B

    The mining industry is among the top ten industries nationwide with high occupational injury and fatality rates, and mine rescue response may be considered one of the most hazardous activities in mining operations. In the aftermath of an underground mine fire, explosion or water inundation, specially equipped and trained teams have been sent underground to fight fires, rescue entrapped miners, test atmospheric conditions, investigate the causes of the disaster, or recover the dead. Special personal protective ensembles are used by the team members to improve the protection of rescuers against the hazards of mine rescue and recovery. Personal protective ensembles used by mine rescue teams consist of helmet, cap lamp, hood, gloves, protective clothing, boots, kneepads, facemask, breathing apparatus, belt, and suspenders. While improved technology such as wireless warning and communication systems, lifeline pulleys, and lighted vests have been developed for mine rescuers over the last 100 years, recent research in this area of personal protective ensembles has been minimal due to the trending of reduced exposure of rescue workers. In recent years, the exposure of mine rescue teams to hazardous situations has been changing. However, it is vital that members of the teams have the capability and proper protection to immediately respond to a wide range of hazardous situations. Currently, there are no minimum requirements, best practice documents, or nationally recognized consensus standards for protective clothing used by mine rescue teams in the United States (U.S.). The following review provides a summary of potential issues that can be addressed by rescue teams and industry to improve potential exposures to rescue team members should a disaster situation occur. However, the continued trending in the mining industry toward non-exposure to potential hazards for rescue workers should continue to be the primary goal. To assist in continuing this trend, the mining industry

  1. Observations on strategic planning of information technology in the Indian coal mining industry

    Energy Technology Data Exchange (ETDEWEB)

    Owen, D.

    1988-05-01

    A view of the needs and plans to improve the coal mining industry of India is presented, focusing primarily on telecommunications and computerization. Further, details on mining electronics and vendor relationships with foreign firms are also discussed. 4 refs.

  2. Moving up down in the mine: Sex segregation in underground coal mining

    Energy Technology Data Exchange (ETDEWEB)

    Tallichet, S.E.

    1991-01-01

    This study employs both individualist theories of human capital and sex-role spillover and structuralist theories from the socialist feminist perspective, emphasizing the formal and informal organizational factors operating within a patriarchal capitalist society to explain job-level sex segregation among underground coal miners. Both quantitative and qualitative data on women in coal mining are used to evaluate these theories. A logistic regression analysis performed on data obtained in 1986 by the US Bureau of Mines demonstrates that while human capital variables are predictive of a miner's job rank, variation in job rank attributed to gender is even greater. For men, training and experience in mining combine to increase the probability of being in a more skilled job in a coal mine. Age and seniority are curvilinearly related to the variation in men's job rank. For women, only age accounts for their advancement such that younger, not older women who have slightly more mining experience, occupy the more skilled positions in the work place. These findings suggest that, in terms of job advancement, men enjoy a greater return on their human capital investments than women, and that factors other than those representing a miner's human capital are affecting women's positions underground more than men's.

  3. Moving up down in the mine: Sex segregation in underground coal mining

    International Nuclear Information System (INIS)

    Tallichet, S.E.

    1991-01-01

    This study employs both individualist theories of human capital and sex-role spillover and structuralist theories from the socialist feminist perspective, emphasizing the formal and informal organizational factors operating within a patriarchal capitalist society to explain job-level sex segregation among underground coal miners. Both quantitative and qualitative data on women in coal mining are used to evaluate these theories. A logistic regression analysis performed on data obtained in 1986 by the US Bureau of Mines demonstrates that while human capital variables are predictive of a miner's job rank, variation in job rank attributed to gender is even greater. For men, training and experience in mining combine to increase the probability of being in a more skilled job in a coal mine. Age and seniority are curvilinearly related to the variation in men's job rank. For women, only age accounts for their advancement such that younger, not older women who have slightly more mining experience, occupy the more skilled positions in the work place. These findings suggest that, in terms of job advancement, men enjoy a greater return on their human capital investments than women, and that factors other than those representing a miner's human capital are affecting women's positions underground more than men's

  4. Locating and defining underground goaf caused by coal mining from space-borne SAR interferometry

    Science.gov (United States)

    Yang, Zefa; Li, Zhiwei; Zhu, Jianjun; Yi, Huiwei; Feng, Guangcai; Hu, Jun; Wu, Lixin; Preusse, Alex; Wang, Yunjia; Papst, Markus

    2018-01-01

    It is crucial to locate underground goafs (i.e., mined-out areas) resulting from coal mining and define their spatial dimensions for effectively controlling the induced damages and geohazards. Traditional geophysical techniques for locating and defining underground goafs, however, are ground-based, labour-consuming and costly. This paper presents a novel space-based method for locating and defining the underground goaf caused by coal extraction using Interferometric Synthetic Aperture Radar (InSAR) techniques. As the coal mining-induced goaf is often a cuboid-shaped void and eight critical geometric parameters (i.e., length, width, height, inclined angle, azimuth angle, mining depth, and two central geodetic coordinates) are capable of locating and defining this underground space, the proposed method reduces to determine the eight geometric parameters from InSAR observations. Therefore, it first applies the Probability Integral Method (PIM), a widely used model for mining-induced deformation prediction, to construct a functional relationship between the eight geometric parameters and the InSAR-derived surface deformation. Next, the method estimates these geometric parameters from the InSAR-derived deformation observations using a hybrid simulated annealing and genetic algorithm. Finally, the proposed method was tested with both simulated and two real data sets. The results demonstrate that the estimated geometric parameters of the goafs are accurate and compatible overall, with averaged relative errors of approximately 2.1% and 8.1% being observed for the simulated and the real data experiments, respectively. Owing to the advantages of the InSAR observations, the proposed method provides a non-contact, convenient and practical method for economically locating and defining underground goafs in a large spatial area from space.

  5. Question marks of the Czech coal mining industry

    International Nuclear Information System (INIS)

    Dopita, M.; Pesek, J.

    1995-01-01

    An overview of brown and black coal mining in the Czech Republic is presented, and problems of the extent of coal reserves and of the profitability of deep black coal mining are discussed. Costs of coal mining in foreign countries are given. Coal mining in the Czech Republic can be expected to be loss-making unless coal prices are increased. Since coal resources in the Czech Republic are limited, additional nuclear power plants will have to be constructed or else coal for power generation will have to be imported. The environmental aspects of coal mining and burning are discussed. Medium-term and long-term solutions to reduce the environmental burden include thermal power plant desulfurization, application of the fluidized-bed combustion regime to coals with large ash and/or sulfur contents, and introduction of gas in towns and power plants. In the short run, large-scale consumers in towns and coal basins should be obliged to accumulate reserves of low-sulfur coal for later use. (J.B.). 2 tabs., 3 figs., 8 refs

  6. Development trends in the Lusatian brown coal mining industry

    International Nuclear Information System (INIS)

    Schwirten, D.

    1994-01-01

    Lusatia has lived on and with brown coal for over 200 years. Brown coal changed what was once a region in which forestry and agriculture predominated into an industrial region. Thanks to its good combustion properties and high energy yield brown coal very soon became known and popular. It was always the driving force for a rapid development which resulted in an economically sound and technically up-to-date industry in Lusatia. This powerful status of brown coal was however soon exploited for aims which were bound to lead to the downfall of two social structures (during the years from 1933 to 1990) by reason of a regime of unconditional autarchy. The economic and technical development thus initiated certainly brought many advantages, but it also had serious diadvantages. Constant increases in production, as a result of which planned rated outputs were intentionally disregarded, were the rule because production targets had to be met or exceeded. Economic inefficiency led to a scarcity of labour and a shortage of finances. Environmental aims had no priority since production was the absolute, primary objective. Consequently, this regime of economic autarchy ended in an one-way street as far as industry was concerned, a situation which was accompanied by an unexampled destruction of the natural basic living conditions and direct, threatening health hazards to man and nature. The year 1990 saw the beginning of the transition from planned controlled economy to free market economy. The reorganization of the former large combines as corporations was not however merely a formal change, but internally also represented a transformation. The brown coal mining industry manifested its new intention and determination to be economically competitive and unsubsidized in future, to operate in such a way as to be compatible with the environment and to exploit reserves carefully, as well as to render its activities socially compatible. (orig.) [de

  7. Interference immunity of blasting circuits in underground coal mining; Zur Stoerfestigkeit von Sprengzuendsystemen im untertaegigen Steinkohlenbergbau

    Energy Technology Data Exchange (ETDEWEB)

    Pfeiler, C.

    1995-02-14

    Blasting technique with electric detonators is a standard instrument e.g. for drift heading in underground coal mining. The simultaneous increase of compactness and efficiency of electrical devices especially in underground mining calls for a careful consideration of susceptibility problems. As an interference of an inadmissible high level might cause a hazardous ignition limiting values and technical parameters of interference to electrical blasting circuits are evaluated. The sources of interference are classified into communication and power technique devices. Typical interference field strengths are determined by exemplary measurements and a model of wave propagation in underground galleries. An equivalent circuit of the impedance of typical electro-explosive devices used in German coal mining is evaluated and extended by an electro-thermal part based on the `Rosenthal equation`. By this means it is possible to determine a feasible ignition during a simulation using the calculated bridge wire temperature. (orig.) [Deutsch] Fuer den untertaegigen Steinkohlenbergbau ist die Sprengtechnik sowohl im Bereich der Streckenauffahrung als auch beim Schachtabteufen heute noch ein wichtiges Arbeitsinstrument. Dabei wird ausschliesslich die elektrische Zuendung eingesetzt. Durch den Trend zu kompakteren elektrischen Systemen bei gleichzeitiger Leistungssteigerung in Verbindung mit den geringen raeumlichen Abstaenden unter Tage gewinnen Phaenomene der elektromagnetischen Beeinflussung auch im Steinkohlenbergbau an Bedeutung. Eine unzulaessig hohe Beeinflussung des elektrischen Zuendsystems kann eine unerwuenschte Fruehzuendung verursachen. Dieses Gefahrenpotential erfordert eine gesonderte Untersuchung der Stoerfestigkeit elektrischer Zuendsysteme, zumal die Normen fuer den uebertaegigen Sprengbetrieb unter Tage aufgrund der unterschiedlichen Randbedingungen der Ausbreitung elektromagnetischer Wellen nicht uneingeschraenkt angewendet werden koennen. Die Stoerquellen der

  8. Mechanization of operations in underground workings in coal mines and research project trends. [Poland

    Energy Technology Data Exchange (ETDEWEB)

    Reich, K; Skoczynski, W; Sikora, W

    1985-01-01

    Structure of black coal reserves of Poland, imported and Polish made equipment for underground mining, prospects for mechanization of selected operations in underground mines and research programs of the KOMAG Center for Mechanization of Mining are evaluated. Prospects for longwall mining with caving or stowing in thick coal seams (slice mining), thin (0.8 to 1.2 m), level or inclined coal seams and steep seams are analyzed. The following equipment for mechanization of underground mining is evaluated: integrated face systems, shearer loaders, chain conveyors, belt conveyors, coal plows, equipment for mine drivage, hoists, drive systems for mining equipment. The following research programs of the KOMAG Center are reviewed: modernization of face systems for coal seams with uncomplicated mining conditions, development of equipment for thin seam mining, development of types of mining equipment for coal seams from 1.5 to 3.0 m thick with dip angles to 25 degrees, modernization of equipment for thick seam mining, increasing efficiency of mine drivage (new types of heading machines, materials handling equipment for mine drivage), mechanization of auxiliary operations in underground coal mines, improving quality of mining equipment, development of equipment for coal preparation, increasing occupational safety in underground mining.

  9. 77 FR 20700 - Examinations of Work Areas in Underground Coal Mines for Violations of Mandatory Health or Safety...

    Science.gov (United States)

    2012-04-06

    ... DEPARTMENT OF LABOR Mine Safety and Health Administration 30 CFR Part 75 RIN 1219-AB75 Examinations of Work Areas in Underground Coal Mines for Violations of Mandatory Health or Safety Standards AGENCY: Mine Safety and Health Administration, Labor. ACTION: Final rule. SUMMARY: The Mine Safety and...

  10. 77 FR 43721 - Examinations of Work Areas in Underground Coal Mines for Violations of Mandatory Health or Safety...

    Science.gov (United States)

    2012-07-26

    ... DEPARTMENT OF LABOR Mine Safety and Health Administration 30 CFR Part 75 RIN 1219-AB75 Examinations of Work Areas in Underground Coal Mines for Violations of Mandatory Health or Safety Standards AGENCY: Mine Safety and Health Administration, Labor. ACTION: Notice of OMB approval of information...

  11. Citation-related reliability analysis for a pilot sample of underground coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Kinilakodi, H.; Grayson, R.L. [Penn State University, University Park, PA (United States)

    2011-05-15

    The scrutiny of underground coal mine safety was heightened because of the disasters that occurred in 2006-2007, and more recently in 2010. In the aftermath of the 2006 incidents, the U.S. Congress passed the Mine Improvement and New Emergency Response Act of 2006 (MINER Act), which strengthened the existing regulations and mandated new laws to address various issues related to emergency preparedness and response, escape from an emergency situation, and protection of miners. The National Mining Association-sponsored Mine Safety Technology and Training Commission study highlighted the role of risk management in identifying and controlling major hazards, which are elements that could come together and cause a mine disaster. In 2007 MSHA revised its approach to the 'Pattern of Violations' (POV) process in order to target unsafe mines and then force them to remediate conditions in their mines. The POV approach has certain limitations that make it difficult for it to be enforced. One very understandable way to focus on removing threats from major-hazard conditions is to use citation-related reliability analysis. The citation reliability approach, which focuses on the probability of not getting a citation on a given inspector day, is considered an analogue to the maintenance reliability approach, which many mine operators understand and use. In this study, the citation reliability approach was applied to a stratified random sample of 31 underground coal mines to examine its potential for broader application. The results clearly show the best-performing and worst-performing mines for compliance with mine safety standards, and they highlight differences among different mine sizes.

  12. Human health and safety risks management in underground coal mines using fuzzy TOPSIS

    Energy Technology Data Exchange (ETDEWEB)

    Mahdevari, Satar, E-mail: satar.mahdevari@aut.ac.ir [Department of Mining and Metallurgical Engineering, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Shahriar, Kourosh [Department of Mining and Metallurgical Engineering, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Esfahanipour, Akbar [Industrial Engineering Department, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of)

    2014-08-01

    The scrutiny of health and safety of personnel working in underground coal mines is heightened because of fatalities and disasters that occur every year worldwide. A methodology based on fuzzy TOPSIS was proposed to assess the risks associated with human health in order to manage control measures and support decision-making, which could provide the right balance between different concerns, such as safety and costs. For this purpose, information collected from three hazardous coal mines namely Hashouni, Hojedk and Babnizu located at the Kerman coal deposit, Iran, were used to manage the risks affecting the health and safety of their miners. Altogether 86 hazards were identified and classified under eight categories: geomechanical, geochemical, electrical, mechanical, chemical, environmental, personal, and social, cultural and managerial risks. Overcoming the uncertainty of qualitative data, the ranking process is accomplished by fuzzy TOPSIS. After running the model, twelve groups with different risks were obtained. Located in the first group, the most important risks with the highest negative effects are: materials falling, catastrophic failure, instability of coalface and immediate roof, firedamp explosion, gas emission, misfire, stopping of ventilation system, wagon separation at inclines, asphyxiation, inadequate training and poor site management system. According to the results, the proposed methodology can be a reliable technique for management of the minatory hazards and coping with uncertainties affecting the health and safety of miners when performance ratings are imprecise. The proposed model can be primarily designed to identify potential hazards and help in taking appropriate measures to minimize or remove the risks before accidents can occur. - Highlights: • Risks associated with health and safety of coal miners were investigated. • A reliable methodology based on Fuzzy TOPSIS was developed to manage the risks. • Three underground mines in Kerman

  13. Human health and safety risks management in underground coal mines using fuzzy TOPSIS

    International Nuclear Information System (INIS)

    Mahdevari, Satar; Shahriar, Kourosh; Esfahanipour, Akbar

    2014-01-01

    The scrutiny of health and safety of personnel working in underground coal mines is heightened because of fatalities and disasters that occur every year worldwide. A methodology based on fuzzy TOPSIS was proposed to assess the risks associated with human health in order to manage control measures and support decision-making, which could provide the right balance between different concerns, such as safety and costs. For this purpose, information collected from three hazardous coal mines namely Hashouni, Hojedk and Babnizu located at the Kerman coal deposit, Iran, were used to manage the risks affecting the health and safety of their miners. Altogether 86 hazards were identified and classified under eight categories: geomechanical, geochemical, electrical, mechanical, chemical, environmental, personal, and social, cultural and managerial risks. Overcoming the uncertainty of qualitative data, the ranking process is accomplished by fuzzy TOPSIS. After running the model, twelve groups with different risks were obtained. Located in the first group, the most important risks with the highest negative effects are: materials falling, catastrophic failure, instability of coalface and immediate roof, firedamp explosion, gas emission, misfire, stopping of ventilation system, wagon separation at inclines, asphyxiation, inadequate training and poor site management system. According to the results, the proposed methodology can be a reliable technique for management of the minatory hazards and coping with uncertainties affecting the health and safety of miners when performance ratings are imprecise. The proposed model can be primarily designed to identify potential hazards and help in taking appropriate measures to minimize or remove the risks before accidents can occur. - Highlights: • Risks associated with health and safety of coal miners were investigated. • A reliable methodology based on Fuzzy TOPSIS was developed to manage the risks. • Three underground mines in Kerman

  14. Early detection of spontaneous combustion of coal in underground coal mines with development of an ethylene enriching system

    Energy Technology Data Exchange (ETDEWEB)

    Xie, Jun; Xue, Sheng [CSIRO Earth Science and Resource Engineering, Kenmore (Australia); Cheng, Weimin; Wang, Gang [Shandong University of Science and Technology, Qingdao (China)

    2011-01-01

    Spontaneous combustion of coal (sponcom) is a major hazard in underground coal mining operations. If not detected early and managed properly, it can seriously affect mine safety and productivity. Gaseous products of sponcom, such as carbon monoxide, ethylene and hydrogen, are commonly used in coal mines as indicators to reflect the state of the sponcom. Studies have shown that ethylene starts to occur when sponcom reaches a characteristic temperature. However, due to dilution of ventilation air and detection limits of the instruments used for gas analysis at coal mines, ethylene cannot be detected until the sponcom has developed past its early stage, missing an optimum opportunity for mine operators to control the hazard. To address the issue, an ethylene-enriching system, based on its physical adsorption and desorption properties, has been developed to increase detection sensitivity of the ethylene concentration in mine air by about 10 times. This system has successfully been applied in a number of underground coal mines in China to detect sponcom at its early stage and enable mine operators to take effective control measures. This paper describes the ethylene enriching system and its application. (author)

  15. Radon as a tracer of daily, seasonal and spatial air movements in the Underground Tourist Route "Coal Mine" (SW Poland).

    Science.gov (United States)

    Tchorz-Trzeciakiewicz, Dagmara Eulalia; Parkitny, Tomasz

    2015-11-01

    The surveys of radon concentrations in the Underground Tourist Route "Coal Mine" were carried out using passive and active measurement techniques. Passive methods with application of Solid State Nuclear Track Detectors LR115 were used at 4 points in years 2004-2007 and at 21 points in year 2011. These detectors were exchanged at the beginning of every season in order to get information about seasonal and spatial changes of radon concentrations. The average radon concentration noted in this facility was 799 Bq m(-3) and is consistent with radon concentrations noted in Polish coal mines. Seasonal variations, observed in this underground tourist route, were as follows: the highest radon concentrations were noted during summers, the lowest during winters, during springs and autumns intermediate but higher in spring than in autumn. The main external factor that affected seasonal changes of radon concentrations was the seasonal variation of outside temperature. No correlation between seasonal variations of radon concentrations and seasonal average atmospheric pressures was found. Spatial variations of radon concentrations corresponded with air movements inside the Underground Tourist Route "Coal Mine". The most vivid air movements were noted along the main tunnel in adit and at the place located near no blinded (in the upper part) shaft. Daily variations of radon concentrations were recorded in May 2012 using RadStar RS-230 as the active measurement technique. Typical daily variations of radon concentrations followed the pattern that the highest radon concentrations were recorded from 8-9 a.m. to 7-8 p.m. and the lowest during nights. The main factor responsible for hourly variations of radon concentrations was the daily variation of outside temperatures. No correlations were found between radon concentration and other meteorological parameters such as atmospheric pressure, wind velocity or precipitation. Additionally, the influence of human factor on radon

  16. Underground aboveground. Technology and market of coal mining in Dutch Limburg during the eighteenth and nineteenth centuries

    International Nuclear Information System (INIS)

    Gales, B.P.A.

    2002-01-01

    This book considers the development of coal mining in the Dutch province of Limburg during the eighteenth and nineteenth centuries. It is focused on the technical development and its economic background. Within the Dutch borders, as defined at the Congress of Vienna and the Dutch-Prussian negotiations of 1815 and 1816, the mining industry was small. In fact, it only consisted of two mines. (Earlier, more companies of miners had been working in the area since the Middle Ages). The two mines, however, had a certain symbolic importance for contemporaries. Most telling was the stubborn refusal to cede coal-ground to Prussia, ending in a remarkable compromise. The new national frontier was different above and underground. Underground the old borders were maintained. Thus it came about that in matters of mining, the Dutch were locally sovereign under a foreign surface. This fact itself shows that the political divisions of the nineteenth and twentieth centuries were rather artificial constructions. Dutch coal-strata were a continuation of the seams of the Worm-basin or the Aachen coal field. The Dutch collieries were just the most north-western ones of a whole series, the Worm-mines, until new pits were constructed around the turn of the nineteenth and into the twentieth centuries and modem mining in the Dutch-Limburg field took off. This is also the more general perspective taken in this book. Developments on the Dutch side of the border are contrasted with those on the German side. Furthermore, the evolution of the mines between Aachen in Germany and the Dutch town Kerkrade are considered in the light of what happened in the neighbourhood of Liege (Belgium) and the mining districts further south in Belgium, the north of France and both the Ruhr and Saar districts in Germany. In short, the Austrasian field, the concept framed by Wrigley in 1962, is the locus of reference. The symbolic importance of Dutch coal mining stimulated a series of experiments in bringing the

  17. Application of decision tree model for the ground subsidence hazard mapping near abandoned underground coal mines.

    Science.gov (United States)

    Lee, Saro; Park, Inhye

    2013-09-30

    Subsidence of ground caused by underground mines poses hazards to human life and property. This study analyzed the hazard to ground subsidence using factors that can affect ground subsidence and a decision tree approach in a geographic information system (GIS). The study area was Taebaek, Gangwon-do, Korea, where many abandoned underground coal mines exist. Spatial data, topography, geology, and various ground-engineering data for the subsidence area were collected and compiled in a database for mapping ground-subsidence hazard (GSH). The subsidence area was randomly split 50/50 for training and validation of the models. A data-mining classification technique was applied to the GSH mapping, and decision trees were constructed using the chi-squared automatic interaction detector (CHAID) and the quick, unbiased, and efficient statistical tree (QUEST) algorithms. The frequency ratio model was also applied to the GSH mapping for comparing with probabilistic model. The resulting GSH maps were validated using area-under-the-curve (AUC) analysis with the subsidence area data that had not been used for training the model. The highest accuracy was achieved by the decision tree model using CHAID algorithm (94.01%) comparing with QUEST algorithms (90.37%) and frequency ratio model (86.70%). These accuracies are higher than previously reported results for decision tree. Decision tree methods can therefore be used efficiently for GSH analysis and might be widely used for prediction of various spatial events. Copyright © 2013. Published by Elsevier Ltd.

  18. Evaluation of the mortality standard of a miners cohort exposed to radon in an underground coal mining, Parana, Brazil

    International Nuclear Information System (INIS)

    Veiga, Lene H.S.; Amaral, Eliana C.S.; Koifman, Sergio

    2005-01-01

    This study aims to to evaluate the possible health effects on workers in a underground coal mining that were exposed to radon and its decay products without the knowledge of the exposure risk. We established a historical cohort of workers in this mining which included 2856 workers, 1946 underground workers and 910 surface workers, and was carried out a retrospective tracking of mortality in this cohort between 1979 and 2002. Through multiple strategies for monitoring, involving several national institutions, was possible to trace the vital status of 92% of the cohort and 100% of the causes of deaths. The results showed that employees of underground coal mining in Parana had a risk of mortality from lung cancer higher than might be expected to the male population of the state of Parana, observing an increase in risk with the time of underground service. However, this increase in mortality from lung cancer was not observed for surface workers. Among several carcinogenic agents present in the mine environment, radon gas and its decay products can be identified as the major cause for this increase in risk of lung cancer for these workers, once other epidemiological studies in coal mining, which have no risk of exposure to radon, do not present an increased of mortality risk from lung cancer

  19. Profitability and occupational injuries in U.S. underground coal mines.

    Science.gov (United States)

    Asfaw, Abay; Mark, Christopher; Pana-Cryan, Regina

    2013-01-01

    Coal plays a crucial role in the U.S. economy yet underground coal mining continues to be one of the most dangerous occupations in the country. In addition, there are large variations in both profitability and the incidence of occupational injuries across mines. The objective of this study was to examine the association between profitability and the incidence rate of occupational injuries in U.S. underground coal mines between 1992 and 2008. We used mine-specific data on annual hours worked, geographic location, and the number of occupational injuries suffered annually from the employment and accident/injury databases of the Mine Safety and Health Administration, and mine-specific data on annual revenue from coal sales, mine age, workforce union status, and mining method from the U.S. Energy Information Administration. A total of 5669 mine-year observations (number of mines×number of years) were included in our analysis. We used a negative binomial random effects model that was appropriate for analyzing panel (combined time-series and cross-sectional) injury data that were non-negative and discrete. The dependent variable, occupational injury, was measured in three different and non-mutually exclusive ways: all reported fatal and nonfatal injuries, reported nonfatal injuries with lost workdays, and the 'most serious' (i.e. sum of fatal and serious nonfatal) injuries reported. The total number of hours worked in each mine and year examined was used as an exposure variable. Profitability, the main explanatory variable, was approximated by revenue per hour worked. Our model included mine age, workforce union status, mining method, and geographic location as additional control variables. After controlling for other variables, a 10% increase in real total revenue per hour worked was associated with 0.9%, 1.1%, and 1.6% decrease, respectively, in the incidence rates of all reported injuries, reported injuries with lost workdays, and the most serious injuries reported

  20. Managerial Accounting Principles and Cost Calculation Used by Economic Entities in the Coal Mining Industry

    OpenAIRE

    Boca (Rakos) Ileana – Sorina; Vatasoiu Cristian Ionel

    2011-01-01

    Considering the specialized work in managerial accounting, this paper aims to show which cost calculation principles are actually applied in the coal mining industry today. The methodology used in this scientific approach is of qualitative nature, using the following methods: direct observation and interview.

  1. Hydrologic and water quality characteristics of a partially-flooded, abandoned underground coal mine

    International Nuclear Information System (INIS)

    Aljoe, W.W.

    1994-01-01

    The hydrologic and water quality characteristics of a partially flooded, abandoned underground coal mine near Latrobe, PA, were studied to support the development of techniques for in situ abatement of its acidic discharge. A quantitative understanding of the conditions affecting discharge flow was considered to be very important in this regard. Statistical analysis of hydrologic data collected at the site shows that the flow rate of the main discharge (a borehole that penetrates the mine workings just behind a set of portal seals) is a linear function of the height of the mine pool above the borehole outlet. Seepage through or around the portal seals is collected by a set of french drains whose discharge rate is largely independent of the mine pool elevation. This seepage was enhanced after a breakthrough that occurred during a period of unusually high pool levels. The mine pool recharge rate during winter is about 2.5 times greater than that of any other season; recharge rates during spring, summer, and fall are approximately equal. Mine pool and discharge water quality information, along with bromide tracer tests, suggest that the original main entries discharge primarily to the french drains, while the borehole carries the discharge from an unmonitored set of entries northwest of the mains. The water quality of the east french drain discharge may have been improved substantially after seepage through the alkaline materials used to construct the portal seals

  2. Human action quality evaluation based on fuzzy logic with application in underground coal mining.

    Science.gov (United States)

    Ionica, Andreea; Leba, Monica

    2015-01-01

    The work system is defined by its components, their roles and the relationships between them. Any work system gravitates around the human resource and the interdependencies between human factor and the other components of it. Researches in this field agreed that the human factor and its actions are difficult to quantify and predict. The objective of this paper is to apply a method of human actions evaluation in order to estimate possible risks and prevent possible system faults, both at human factor level and at equipment level. In order to point out the importance of the human factor influence on all the elements of the working systems we propose a fuzzy logic based methodology for quality evaluation of human actions. This methodology has a multidisciplinary character, as it gathers ideas and methods from: quality management, ergonomics, work safety and artificial intelligence. The results presented refer to a work system with a high degree of specificity, namely, underground coal mining and are valuable for human resources risk evaluation pattern. The fuzzy logic evaluation of the human actions leads to early detection of possible dangerous evolutions of the work system and alarm the persons in charge.

  3. Injection of alkaline ashes into underground coal mines for acid mine drainage abatement

    International Nuclear Information System (INIS)

    Aljoe, W.W.

    1996-01-01

    The injection of alkaline coal combustion waste products into abandoned underground coal mines for acid mine drainage (AMD) abatement has obvious conceptual appeal. This paper summarizes the findings of the baseline hydrogeologic and water quality evaluations at two sites--one in West Virginia and one in Maryland--where field demonstrations of the technique are being pursued in cooperative efforts among State and Federal agencies and/or private companies. The West Virginia site produces severe AMD from three to seven AMD sources that are spaced over about a 1.2 km stretch of the down-dip side of the mine workings. By completely filling the most problematic portion of the mine workings with coal combustion ashes, the State expects that the costs and problems associated with AMD treatment will be greatly reduced. At the Maryland site, it is expected that the AMD from a relatively small target mine will be eliminated completely by filling the entire mine void with a grout composed of a mixture of fly ash, fluidized-bed combustion ash, and flue gas desulfurization sludge. This project will also demonstrate the potential cost-effectiveness of the technique at other sites, both for the purpose of AMD remediation and control of land subsidence

  4. A comparison of physiological strain of carriers in underground manual coal mines in India

    Energy Technology Data Exchange (ETDEWEB)

    Saha, R.; Dey, N.C.; Samanta, A.; Biswas, R. [University College of Medical Science, Lumbini (Nepal). Dept. of Physics

    2008-07-15

    Thirty nine healthy carriers (23-57 years of age) were investigated in underground manual coal mines in West Bengal, India during two different work spells of a single work shift. We compared physiological strain of workers <40 and {ge} 40 years of age. For both groups, mean heart rate was 124-133 beats/min, with a mean corresponding relative cardiac cost of 50-66%. Maximum aerobic capacities were estimated indirectly, following a standard step test protocol. Average oxygen consumption was 1.07-1.1 l/min, with an energy expenditure of 5.35-5.5 kcal/min among both age groups. Acceptable levels of physiological strain were well encroached, and older workers faced the maximum burden. The tasks studied were heavy to very heavy in nature. The weight of load carriage at a spontaneously chosen speed and the prevailing environmental conditions merit serious attention. There is extreme need of ergonomic interventions in reducing the postural load and musculoskeletal discomforts in this population.

  5. Using tracers to understand the hydrology of an abandoned underground coal mine

    International Nuclear Information System (INIS)

    Canty, G.A.; Everett, J.W.

    1998-01-01

    Flooded underground mines pose a difficult problem for remediation efforts requiring hydrologic information. Mine environments are hydraulically complicated due to sinuous travel paths and variable hydraulic gradients. For an acidic mine remediation project, conducted by the University of Oklahoma in conjunction with the Oklahoma Conservation Commission, a tracer study was undertaken to identify basic hydrologic properties of a flooded coal mine. The study was conducted to investigate the possibility of in-situ remediation of acidic mine water with the use of alkaline coal combustion by-products. Information on the rate of flow and ''connectiveness'' of injection wells with the discharge point was needed to develop a treatment strategy. Fluorescent dyes are not typically used in mine tracer studies because of the low pH values associated with certain mines and a tendency to adsorb ferric iron precipitates. However, Rhodamine WT was used in one tracer test because it can be detected at low concentrations. Due to poor recovery, a second tracer test was undertaken using a more conservative tracer-chloride. Each tracer produced similar travel time results. Findings from this study suggest that Rhodamine WT can be used under slightly acidic conditions, with mixed results. The more conservative tracer provided somewhat better results, but recovery was still poor. Use of these tracers has provided some valuable information with regard to mine hydrology, but additional questions have been raised

  6. Radium balance in discharge waters from coal mines in Poland the ecological impact of underground water treatment

    International Nuclear Information System (INIS)

    Chalupnik, S.; Wysocka, M.

    2008-01-01

    Saline waters from underground coal mines in Poland often contain natural radioactive isotopes, mainly 226 Ra from the uranium decay series and 228 Ra from the thorium series. More than 70% of the total amount of radium remains underground as radioactive deposits due to spontaneous co-precipitation or water treatment technologies, but several tens of MBq of 226 Ra and even higher activity of 228 Ra are released daily into the rivers along with the other mine effluents from all Polish coal mines. Mine waters can have a severe impact on the natural environment, mainly due to its salinity. Additionally high levels of radium concentration in river waters, bottom sediments and vegetation were also observed. Sometimes radium concentrations in rivers exceeded 0.7 kBq/m 3 , which was the permitted level for wastewaters under Polish law. The investigations described here were carried out for all coal mines and on this basis the total radium balance in effluents has been calculated. Measurements in the vicinity of mine settling ponds and in rivers have given an opportunity to study radium behaviour in river waters and to assess the degree of contamination. For removal of radium from saline waters a method of purification has been developed and implemented in full technical scale in two of Polish coal mines. The purification station in Piast Colliery was unique, the first underground installation for the removal of radium isotopes from saline waters. Very good results have been achieved - approximately 6 m 3 /min of radium-bearing waters were treated there, more than 100 MBq of 226 Ra and 228 Ra remained underground each day. Purification has been started in 1999, therefore a lot of experiences have been gathered during this period. Since year 2006, a new purification station is working in another colliery, Ziemowit, at the level -650 meters. Barium chloride is used as a cleaning , agent, and amount of water to be purified is reaching 9 m 3 /min. Technical measures such as

  7. Injection of FGD Grout to Abate Acid Mine Drainage in Underground Coal Mines

    Energy Technology Data Exchange (ETDEWEB)

    Mafi, S.; Damian, M.T.; Senita, R.E.; Jewitt, W.C.; Bair, S.; Chin, Y.C.; Whitlatch, E.; Traina, S.; Wolfe, W.

    1997-07-01

    Acid Mine Drainage (AMD) from abandoned underground coal mines in Ohio is a concern for both residents and regulatory agencies. Effluent from these mines is typically characterized by low pH and high iron and sulfate concentrations and may contaminate local drinking-water supplies and streams. The objective of this project is to demonstrate the technical feasibility of injecting cementitious alkaline materials, such as Flue Gas Desulfurization (FGD) material to mitigate current adverse environmental impacts associated with AMD in a small, abandoned deep mine in Coshocton County Ohio. The Flue Gas Desulfurization material will be provided from American Electric Power`s (AEP) Conesville Plant. It will be injected as a grout mix that will use Fixated Flue Gas Desulfurization material and water. The subject site for this study is located on the border of Coshocton and Muskingum Counties, Ohio, approximately 1.5 miles south-southwest of the town of Wills Creek. The study will be performed at an underground mine designated as Mm-127 in the Ohio Department of Natural Resources register, also known as the Roberts-Dawson Mine. The mine operated in the mid-1950s, during which approximately 2 million cubic feet of coal was removed. Effluent discharging from the abandoned mine entrances has low pH in the range of 2.8-3.0 that drains directly into Wills Creek Lake. The mine covers approximately 14.6 acres. It is estimated that 26,000 tons of FGD material will be provided from AEP`s Conesville Power Plant located approximately 3 miles northwest of the subject site.

  8. Injection of FGD Grout to Abate Acid Mine Drainage in Underground Coal Mines

    International Nuclear Information System (INIS)

    Mafi, S.; Damian, M.T.; Senita, R.E.; Jewitt, W.C.; Bair, S.; Chin, Y.C.; Whitlatch, E.; Traina, S.; Wolfe, W.

    1997-07-01

    Acid Mine Drainage (AMD) from abandoned underground coal mines in Ohio is a concern for both residents and regulatory agencies. Effluent from these mines is typically characterized by low pH and high iron and sulfate concentrations and may contaminate local drinking-water supplies and streams. The objective of this project is to demonstrate the technical feasibility of injecting cementitious alkaline materials, such as Flue Gas Desulfurization (FGD) material to mitigate current adverse environmental impacts associated with AMD in a small, abandoned deep mine in Coshocton County Ohio. The Flue Gas Desulfurization material will be provided from American Electric Power's (AEP) Conesville Plant. It will be injected as a grout mix that will use Fixated Flue Gas Desulfurization material and water. The subject site for this study is located on the border of Coshocton and Muskingum Counties, Ohio, approximately 1.5 miles south-southwest of the town of Wills Creek. The study will be performed at an underground mine designated as Mm-127 in the Ohio Department of Natural Resources register, also known as the Roberts-Dawson Mine. The mine operated in the mid-1950s, during which approximately 2 million cubic feet of coal was removed. Effluent discharging from the abandoned mine entrances has low pH in the range of 2.8-3.0 that drains directly into Wills Creek Lake. The mine covers approximately 14.6 acres. It is estimated that 26,000 tons of FGD material will be provided from AEP's Conesville Power Plant located approximately 3 miles northwest of the subject site

  9. Structural implications of underground coal mining in the Mesaverde Group in the Somerset Coal Field, Delta and Gunnison Counties, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Christopher J. Carroll; Eric Robeck; Greg Hunt; Wendell Koontz [Colorado Geological Survey, Denver, CO (United States)

    2004-07-01

    Paleogene and Neogene faults and fractures on the eastern edge of the Colorado Plateau are present in Mesaverde Group coal and sandstone beds. Recent observations of coal cleat orientation in relation to faults in coal mines have significant impacts for mine planning in the area. Faults, coal cleats, and natural fractures are interpreted to show a structural evolution of the Mesaverde Group through time. This field trip included a visit to two active underground coal mines, the Bowie Resources' Bowie No. 2 Mine, and Mountain Coal's West Elk Mine. Mine geologists discussed structural styles including fault orientations and timing, cleat development, and rotation. Geologic encounters ranging from fault flooding, subsidence, mine fires, methane gas problems, and land use restrictions were also discussed. Coal cleat development and open-mode fractures in adjacent sandstones were observed on outcrops and compared to underground measurements in coal mines in the Somerset Coal Field, Colorado's most productive. Coal cleat orientations along a reverse fault in one mine showed rotation in relation to possible Neogene age displacement.

  10. Development of science and technology in underground coal mining in Czechoslovakia during the 7th 5 year plan

    Energy Technology Data Exchange (ETDEWEB)

    Klimek, M.

    1982-01-01

    Reviews main tasks of underground coal mining in Czechoslovakia from 1981 to 1985 in the following basins: Ostrava-Karvina, Kladno, Prievidza, Most and Sokolov. The planned increase of brown and black coal output in each of the basins is discussed. Selected problems associated with mining are evaluated: significant increase of mining depth, rock burst hazards, methane hazards and water influx in the Ostrava-Karvina basin. Investment program in the current 5 year plan as well as until the year 2000 is analyzed: sinking of 38.8 km of mine shafts and 4.4 km of blind shafts. Equipment for shaft sinking produced in the USA (by Robins the 241 SB-184) and in the USSR (the Uralmash Sk-1U system) is compared. Design and technical specifications of the two systems are given. Equipment for mine drivage is also reviewed. The following machines are described: the TVM-55H by Demag (FRG), the TBS V-600E/Sch by Wirth (FRG), the TBM ser. 18a781 by Robins (USA) and the MARK-18T by JARVA (USA). Selected types of powered supports which will be widely used in coal mines in the current 5 year plan are evaluated. Research programs in underground coal mining are reviewed (safety, mining thin coal seams, slice mining of thick coal seams in the Namurian B series, mining extremely thick seams with stowing of the top slice and mining with caving the 4.5 m thick bottom slice). (4 refs.) (In Czech)

  11. Coal mining in the power industry of the Federal Republic of Germany in 1993

    International Nuclear Information System (INIS)

    1994-11-01

    After an introductory text divided into the sections energy and coal market, Coal mining and brown coal mining, extensive tables containing the most important characteristic figures of German coal mining are shown. (orig.) [de

  12. The South Manchurian Railway Company and the Mining Industry: The Case of the Fushun Coal Mine

    Directory of Open Access Journals (Sweden)

    Tsu-yu Chen

    2015-09-01

    Full Text Available Following the Japanese victory over Czarist Russia in the Russo-Japanese War and the signing of the Treaty of Portsmouth in 1905, the southernmost section of the southern branch of the China Far East Railway (Changchun–Port Arthur was transferred to Japanese control. A new, semi-privately held company, the South Manchuria Railway Company (SMR, Mantetsu, was established with 85.6 percent capitalization by the Japanese government and foreign bonds to operate the railroad and to develop settlements (including highways, public health facilities, educational institutions, and industries (coal mines, harbor facilities, electrical power plants, shale oil plants, chemical plants, and restaurants along its route. SMR nonetheless emphasized railway and mining investment. The centerpiece of its mining interests was the Fushun Coal Mine. Starting in 1917, SMR began to prosper, with most profits coming from its coal mines, and it soon spun off subsidiary companies. In this sense, although the factors that influenced development of the Fushun Coal Mine in each period were different, this development still shows continuity of the business management.

  13. An Event Reporting and Early-Warning Safety System Based on the Internet of Things for Underground Coal Mines: A Case Study

    Directory of Open Access Journals (Sweden)

    Byung Wan Jo

    2017-09-01

    Full Text Available Fatal accidents associated with underground coal mines require the implementation of high-level gas monitoring and miner’s localization approaches to promote underground safety and health. This study introduces a real-time monitoring, event-reporting and early-warning platform, based on cluster analysis for outlier detection, spatiotemporal statistical analysis, and an RSS range-based weighted centroid localization algorithm for improving safety management and preventing accidents in underground coal mines. The proposed platform seamlessly integrates monitoring, analyzing, and localization approaches using the Internet of Things (IoT, cloud computing, a real-time operational database, application gateways, and application program interfaces. The prototype has been validated and verified at the operating underground Hassan Kishore coal mine. Sensors for air quality parameters including temperature, humidity, CH4, CO2, and CO demonstrated an excellent performance, with regression constants always greater than 0.97 for each parameter when compared to their commercial equivalent. This framework enables real-time monitoring, identification of abnormal events (>90%, and verification of a miner’s localization (with <1.8 m of error in the harsh environment of underground mines. The main contribution of this study is the development of an open source, customizable, and cost-effective platform for effectively promoting underground coal mine safety. This system is helpful for solving the problems of accessibility, serviceability, interoperability, and flexibility associated with safety in coal mines.

  14. Zoning method for environmental engineering geological patterns in underground coal mining areas.

    Science.gov (United States)

    Liu, Shiliang; Li, Wenping; Wang, Qiqing

    2018-09-01

    Environmental engineering geological patterns (EEGPs) are used to express the trend and intensity of eco-geological environment caused by mining in underground coal mining areas, a complex process controlled by multiple factors. A new zoning method for EEGPs was developed based on the variable-weight theory (VWT), where the weights of factors vary with their value. The method was applied to the Yushenfu mining area, Shaanxi, China. First, the mechanism of the EEGPs caused by mining was elucidated, and four types of EEGPs were proposed. Subsequently, 13 key control factors were selected from mining conditions, lithosphere, hydrosphere, ecosphere, and climatic conditions; their thematic maps were constructed using ArcGIS software and remote-sensing technologies. Then, a stimulation-punishment variable-weight model derived from the partition of basic evaluation unit of study area, construction of partition state-variable-weight vector, and determination of variable-weight interval was built to calculate the variable weights of each factor. On this basis, a zoning mathematical model of EEGPs was established, and the zoning results were analyzed. For comparison, the traditional constant-weight theory (CWT) was also applied to divide the EEGPs. Finally, the zoning results obtained using VWT and CWT were compared. The verification of field investigation indicates that VWT is more accurate and reliable than CWT. The zoning results are consistent with the actual situations and the key of planning design for the rational development of coal resources and protection of eco-geological environment. Copyright © 2018 Elsevier B.V. All rights reserved.

  15. Determining origin of underground water in coal mines by means of natural isotopes and other geochemical parameters

    Energy Technology Data Exchange (ETDEWEB)

    Dolenec, T; Pezdic, J; Herlec, U; Kuscer, D; Mitrevski, G [Institut Josef Stefan, Ljubljana (Yugoslavia)

    1989-07-01

    Presents a preliminary report on origin of water in Slovenian brown coal mines. Water, coal and strata samples from the Hrastnik and Ojstro mines were analyzed for changes in chemical composition. Water samples were also analyzed for changes in isotopic composition and inorganic carbon and sulfur contents. Chemical, isotopic and geochemical techniques are described and results are presented with 21 diagrams. An attempt is made to explain the origin and age of water flowing from mine aquifers into mine rooms, and to explain the interdependence of surface and underground water flow. 10 refs.

  16. R&D status and the performance of domestic firms in China's coal mining industry

    International Nuclear Information System (INIS)

    Sun, Sizhong; Anwar, Sajid

    2015-01-01

    Coal use accounts for a very large proportion of electricity production in China. Using a recently developed coarsened exact matching (CEM) technique, this paper examines the impact of research and development (R&D) activities on the performance of firms in China's coal mining industry. Our empirical results reveal that firms in China's coal industry that conduct R&D are more productive and their sales are higher. However, as far as the firm profitability and market shares are concerned, whether or not a firm in China's coal industry conducts R&D makes no difference. We find that foreign direct investment in China's coal mining industry leads to a significant decrease in the market share of domestic firms and its impact on productivity, sales and profitability of domestic firms is insignificant. The empirical results presented in this paper suggest that policies that encourage domestic firms in China's coal mining industries to conduct R&D can increase domestic production thereby reducing reliance on imports. Furthermore, productivity gains arising from R&D activities can also help Chinese mining firms to improve their competitive position in the international market. However, there is a need for restricting foreign direct investment in China's coal mining industry. - Highlights: • R&D status affects firm performance in China's coal mining industry. • Coal mining firms that conduct R&D are, on average, 0.2717% more productive. • Coal mining firms that conduct R&D experience an increase in sales. • Increase in foreign investment decreases the market share of coal mining firms

  17. Safety Research and Experimental Coal Mines

    Data.gov (United States)

    Federal Laboratory Consortium — Safety Research and Experimental Coal MinesLocation: Pittsburgh SiteThe Safety Research Coal Mine and Experimental Mine complex is a multi-purpose underground mine...

  18. Long-hole destress blasting for rockburst control during deep underground coal mining

    Czech Academy of Sciences Publication Activity Database

    Koníček, Petr; Souček, Kamil; Staš, Lubomír; Singh, R.

    -, č. 61 (2013), s. 141-153 ISSN 1365-1609 R&D Projects: GA MŠk ED2.1.00/03.0082 Institutional support: RVO:68145535 Keywords : Ostrava - Karvina Coal basin * longwall mining * rockbursts * destress blasting Subject RIV: DH - Mining, incl. Coal Mining Impact factor: 1.424, year: 2013 http://www.sciencedirect.com/science/article/pii/S1365160913000348

  19. Physical simulation and theoretical evolution for ground fissures triggered by underground coal mining.

    Science.gov (United States)

    Yang, Jing-Hu; Yu, Xiang; Yang, Yi; Yang, Zeng-Qiang

    2018-01-01

    Underground coal mining activities are prone to cause movement and breakage in geological strata and also lead to mining subsidence and even ground fissures. Along the direction working panel advancing, ground fissures may occur in roof in front and/or behind working panel. However, the investigations of previous similarity tests in lab only emphasize on the region behind working panel. By improving strata material property in construction and mounting artificial pressure devices, two physical simulation tests were conducted and successfully investigated the simulated results. Then, the mechanical model of "cantilever beam and elastic foundation beam" was proposed to calculate the stress distribution and the crack initiation angle in overlying strata and it well explains the mechanisms of ground fissures generation and propagation. Results show that, the maximum internal force in roof always occurred in front of working panel. However, because the void space in gob due to excavation is large enough to cause the bend and rotation of roof strata, compare to the triaxially compressed region in front of working panel, the roof always broke off at some positions above gob since the stress concentration resulting from such bend and rotation of strata could easily reach the limit strength of strata rocks. Also, the length of cantilever beam changed dynamically as respect to the panel advancing and the breakage intervals. Thus, the breakage position where the internal force first reached the limit tensile strength is not fixed and there will be two different kinds of relative positions between the crack initiation point and the working panel. The crack initiation direction is always perpendicular to the internal force, and the crack propagation direction is affected by the initiation angle, overburden-separation degree and the position of the hydraulic shields. If there is no overburden-separation or less, the roofs will break off as a composite beam and the propagation

  20. Physical simulation and theoretical evolution for ground fissures triggered by underground coal mining

    Science.gov (United States)

    Yu, Xiang; Yang, Yi; Yang, Zeng-Qiang

    2018-01-01

    Underground coal mining activities are prone to cause movement and breakage in geological strata and also lead to mining subsidence and even ground fissures. Along the direction working panel advancing, ground fissures may occur in roof in front and/or behind working panel. However, the investigations of previous similarity tests in lab only emphasize on the region behind working panel. By improving strata material property in construction and mounting artificial pressure devices, two physical simulation tests were conducted and successfully investigated the simulated results. Then, the mechanical model of “cantilever beam and elastic foundation beam” was proposed to calculate the stress distribution and the crack initiation angle in overlying strata and it well explains the mechanisms of ground fissures generation and propagation. Results show that, the maximum internal force in roof always occurred in front of working panel. However, because the void space in gob due to excavation is large enough to cause the bend and rotation of roof strata, compare to the triaxially compressed region in front of working panel, the roof always broke off at some positions above gob since the stress concentration resulting from such bend and rotation of strata could easily reach the limit strength of strata rocks. Also, the length of cantilever beam changed dynamically as respect to the panel advancing and the breakage intervals. Thus, the breakage position where the internal force first reached the limit tensile strength is not fixed and there will be two different kinds of relative positions between the crack initiation point and the working panel. The crack initiation direction is always perpendicular to the internal force, and the crack propagation direction is affected by the initiation angle, overburden-separation degree and the position of the hydraulic shields. If there is no overburden-separation or less, the roofs will break off as a composite beam and the

  1. The South African coal mining industry: A need for a more efficient and collaborative supply chain

    Directory of Open Access Journals (Sweden)

    David Pooe

    2011-11-01

    Full Text Available It is estimated that about two-thirds of global coal is used for power generation and that, in the next 20 years, over 70% of the demand for coal will come from China and India. Coal accounts for approximately 41% of the world's electricity generation. Demand for thermal coal is influenced by factors that include availability, prices of competing products such as oil, gas and nuclear power, and the demand for electricity. The aim of this article is to provide an exposition of supply chain dynamics within the South African coal mining industry and to argue for a more efficient and collaborative supply chain. The authors attempt to investigate at local and global level, the current trends pertaining to the level of reserves, production and consumption of coal. The article further demonstrates the shortcomings of current logistics in meeting the demand for coal in both domestic and export markets. The article draws from secondary data sourced from academic papers, government and agency documents in the exposition of the coal mining supply chain. The paper concludes by recommending the need for a scientific study on supply chain constraints facing the coal mining industry in South Africa.

  2. Hydrogeology, groundwater flow, and groundwater quality of an abandoned underground coal-mine aquifer, Elkhorn Area, West Virginia

    Science.gov (United States)

    Kozar, Mark D.; McCoy, Kurt J.; Britton, James Q.; Blake, B.M.

    2017-01-01

    The Pocahontas No. 3 coal seam in southern West Virginia has been extensively mined by underground methods since the 1880’s. An extensive network of abandoned mine entries in the Pocahontas No. 3 has since filled with good-quality water, which is pumped from wells or springs discharging from mine portals (adits), and used as a source of water for public supplies. This report presents results of a three-year investigation of the geology, hydrology, geochemistry, and groundwater flow processes within abandoned underground coal mines used as a source of water for public supply in the Elkhorn area, McDowell County, West Virginia. This study focused on large (> 500 gallon per minute) discharges from the abandoned mines used as public supplies near Elkhorn, West Virginia. Median recharge calculated from base-flow recession of streamflow at Johns Knob Branch and 12 other streamflow gaging stations in McDowell County was 9.1 inches per year. Using drainage area versus mean streamflow relationships from mined and unmined watersheds in McDowell County, the subsurface area along dip of the Pocahontas No. 3 coal-mine aquifer contributing flow to the Turkey Gap mine discharge was determined to be 7.62 square miles (mi2), almost 10 times larger than the 0.81 mi2 surface watershed. Results of this investigation indicate that groundwater flows down dip beneath surface drainage divides from areas up to six miles east in the adjacent Bluestone River watershed. A conceptual model was developed that consisted of a stacked sequence of perched aquifers, controlled by stress-relief and subsidence fractures, overlying a highly permeable abandoned underground coal-mine aquifer, capable of substantial interbasin transfer of water. Groundwater-flow directions are controlled by the dip of the Pocahontas No. 3 coal seam, the geometry of abandoned mine workings, and location of unmined barriers within that seam, rather than surface topography. Seven boreholes were drilled to intersect

  3. 30 CFR 49.20 - Requirements for all coal mines.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Requirements for all coal mines. 49.20 Section... TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.20 Requirements for all coal mines. (a) The operator of each underground coal mine shall make available two certified mine rescue...

  4. Studies of significant properties of filter-type self rescuer for its use in underground coal mine in carbon monoxide exposure

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, A.; Mondal, P.C. [Central Institute of Mining and Fuel Research, Dhanbad (India)

    2007-07-01

    CO is a highly toxic gas; it is the outcome of fire or explosion in underground coal mines. It combines with hemoglobin of coal mine workers and carboxyhemoglobin forms, which reduces the oxygen carrying capacity of blood. A little intake of CO gas, even 0.1% in atmosphere, causes respiratory failure. Filter-type self rescuers (FSR) are a life-saving gas mask breathing apparatus against CO exposure in underground coal mine. The quality of FSR was evaluated in respect of its duration for use, CO conversion by hopcalite, breathing resistance, leak tightness properties, and so on. A scope of improvement is observed in cartridge of self rescuer as well as in the clauses of BIS 9563-1980 in order to increase the duration and improvement in the quality of self rescuers. 12 refs., 2 tabs.

  5. Use of natural gamma radiation in the coal mining industry

    International Nuclear Information System (INIS)

    Wykes, J.S.; Adsley, I.; Cooper, L.R.

    1982-01-01

    The technique of delineating coal seams by the use of natural gamma borehole logging sondes has been known for many years. The principle of the technique is that the gamma fluxes in shales are higher than in coals as the abundance of naturally occurring radionuclides is some twenty times greater in the former. This paper discusses other applications where the differeing natural gamma properties of coals and shales can be used. These are: (a) To distinguish between stone (shale) and run-of-mine coal on conveyor belts. A common situation underground is one in which stone from development headings and normal run-of-mine coal have to be batched along the same conveyor system. A natural gamma device capable of distinguishing between such batches of material, and thus allowing suitable mechanical separation, will be described. (b) To provide an accurate measurement of roof coal thickness by measuring the natural gamma flux penetrating the roof coal. To illustrate this examples will be given where this technique is used to provide automatic controlled steering of Long Wall Shearers and to provide manually assisted steering of In-seam Heading Machines

  6. The Video Collaborative Localization of a Miner’s Lamp Based on Wireless Multimedia Sensor Networks for Underground Coal Mines

    Directory of Open Access Journals (Sweden)

    Kaiming You

    2015-09-01

    Full Text Available Based on wireless multimedia sensor networks (WMSNs deployed in an underground coal mine, a miner’s lamp video collaborative localization algorithm was proposed to locate miners in the scene of insufficient illumination and bifurcated structures of underground tunnels. In bifurcation area, several camera nodes are deployed along the longitudinal direction of tunnels, forming a collaborative cluster in wireless way to monitor and locate miners in underground tunnels. Cap-lamps are regarded as the feature of miners in the scene of insufficient illumination of underground tunnels, which means that miners can be identified by detecting their cap-lamps. A miner’s lamp will project mapping points on the imaging plane of collaborative cameras and the coordinates of mapping points are calculated by collaborative cameras. Then, multiple straight lines between the positions of collaborative cameras and their corresponding mapping points are established. To find the three-dimension (3D coordinate location of the miner’s lamp a least square method is proposed to get the optimal intersection of the multiple straight lines. Tests were carried out both in a corridor and a realistic scenario of underground tunnel, which show that the proposed miner’s lamp video collaborative localization algorithm has good effectiveness, robustness and localization accuracy in real world conditions of underground tunnels.

  7. The Video Collaborative Localization of a Miner's Lamp Based on Wireless Multimedia Sensor Networks for Underground Coal Mines.

    Science.gov (United States)

    You, Kaiming; Yang, Wei; Han, Ruisong

    2015-09-29

    Based on wireless multimedia sensor networks (WMSNs) deployed in an underground coal mine, a miner's lamp video collaborative localization algorithm was proposed to locate miners in the scene of insufficient illumination and bifurcated structures of underground tunnels. In bifurcation area, several camera nodes are deployed along the longitudinal direction of tunnels, forming a collaborative cluster in wireless way to monitor and locate miners in underground tunnels. Cap-lamps are regarded as the feature of miners in the scene of insufficient illumination of underground tunnels, which means that miners can be identified by detecting their cap-lamps. A miner's lamp will project mapping points on the imaging plane of collaborative cameras and the coordinates of mapping points are calculated by collaborative cameras. Then, multiple straight lines between the positions of collaborative cameras and their corresponding mapping points are established. To find the three-dimension (3D) coordinate location of the miner's lamp a least square method is proposed to get the optimal intersection of the multiple straight lines. Tests were carried out both in a corridor and a realistic scenario of underground tunnel, which show that the proposed miner's lamp video collaborative localization algorithm has good effectiveness, robustness and localization accuracy in real world conditions of underground tunnels.

  8. The Video Collaborative Localization of a Miner’s Lamp Based on Wireless Multimedia Sensor Networks for Underground Coal Mines

    Science.gov (United States)

    You, Kaiming; Yang, Wei; Han, Ruisong

    2015-01-01

    Based on wireless multimedia sensor networks (WMSNs) deployed in an underground coal mine, a miner’s lamp video collaborative localization algorithm was proposed to locate miners in the scene of insufficient illumination and bifurcated structures of underground tunnels. In bifurcation area, several camera nodes are deployed along the longitudinal direction of tunnels, forming a collaborative cluster in wireless way to monitor and locate miners in underground tunnels. Cap-lamps are regarded as the feature of miners in the scene of insufficient illumination of underground tunnels, which means that miners can be identified by detecting their cap-lamps. A miner’s lamp will project mapping points on the imaging plane of collaborative cameras and the coordinates of mapping points are calculated by collaborative cameras. Then, multiple straight lines between the positions of collaborative cameras and their corresponding mapping points are established. To find the three-dimension (3D) coordinate location of the miner’s lamp a least square method is proposed to get the optimal intersection of the multiple straight lines. Tests were carried out both in a corridor and a realistic scenario of underground tunnel, which show that the proposed miner’s lamp video collaborative localization algorithm has good effectiveness, robustness and localization accuracy in real world conditions of underground tunnels. PMID:26426023

  9. Key Technologies and Applications of Gas Drainage in Underground Coal Mine

    Science.gov (United States)

    Zhou, Bo; Xue, Sheng; Cheng, Jiansheng; Li, Wenquan; Xiao, Jiaping

    2018-02-01

    It is the basis for the long-drilling directional drilling, precise control of the drilling trajectory and ensuring the effective extension of the drilling trajectory in the target layer. The technology can be used to complete the multi-branch hole construction and increase the effective extraction distance of the coal seam. The gas drainage and the bottom grouting reinforcement in the advanced area are realized, and the geological structure of the coal seam can be proved accurately. It is the main technical scheme for the efficient drainage of gas at home and abroad, and it is applied to the field of geological structure exploration and water exploration and other areas. At present, the data transmission method is relatively mature in the technology and application, including the mud pulse and the electromagnetic wave. Compared with the mud pulse transmission mode, the electromagnetic wave transmission mode has obvious potential in the data transmission rate and drilling fluid, and it is suitable for the coal mine. In this paper, the key technologies of the electromagnetic wave transmission mode are analyzed, including the attenuation characteristics of the electromagnetic transmission channel, the digital modulation scheme, the channel coding method and the weak signal processing technology. A coal mine under the electromagnetic wave drilling prototype is developed, and the ground transmission experiments and down hole transmission test are carried out. The main work includes the following aspects. First, the equivalent transmission line method is used to establish the electromagnetic transmission channel model of coal mine drilling while drilling, and the attenuation of the electromagnetic signal is measured when the electromagnetic channel measured. Second, the coal mine EM-MWD digital modulation method is developed. Third, the optimal linear block code which suitable for EM-MWD communication channel in coal mine is proposed. Fourth, the noise characteristics

  10. Coal mining in the power industry of the Federal Republic of Germany in 2016

    International Nuclear Information System (INIS)

    2017-11-01

    The contribution under consideration reports on the coal mining in the Federal Republic of Germany in the year 2016. Statistical data are presented for the power market and coal market, hard coal mining as well as the brown coal mining. These data consider the energy consumption in Germany, power production, iron and steel production, utilization, re-cultivation and employees.

  11. Coal mining in the power industry of the Federal Republic of Germany in 2015

    International Nuclear Information System (INIS)

    2016-11-01

    The contribution under consideration reports on the coal mining in the Federal Republic of Germany in the year 2015. Statistical data are presented for the power market and coal market, hard coal mining as well as the brown coal mining. These data consider the energy consumption in Germany, power production, iron and steel production, utilization, re-cultivation and employees.

  12. Selected problems of coal mining mechanization in the coal industry of Poland

    Energy Technology Data Exchange (ETDEWEB)

    Antoniak, J; Sikora, W [Politechnika Slaska, Gliwice (Poland)

    1987-01-01

    Discusses conditions for underground coal mining in Poland, types of equipment for coal cutting, mine haulage and strata control and development trends of mining technologies. In 1985, black coal output was 191.6 Mt; 85.3% came from longwall faces mined by sets of mining equipment (coal cutters, chain conveyors and powered supports). The average coal output per longwall face was 881 t/d, output per face mined by sets for mining equipment was 1,134 t/d. In 1985, 653 shearer loaders and 77 coal plows were used in Polish coal mines. Number of shearer loaders is increasing. Shearer loaders with chainless haulage system were safest and most economic. The shearer loaders were equipped with the POLTRAK chainless haulage system developed in Poland. Research programs concentrate on development of new mining equipment for thin seam mining, steep seam mining, longwall mining with hydraulic stowing, efficient strata control by powered or shield supports under conditions of increased stresses or rock burst hazards. 4 refs.

  13. A case of slope slide induced by underground coal mining - analysis for landslide genesis in Hancheng power plant

    Energy Technology Data Exchange (ETDEWEB)

    Xun, Gu

    1988-01-01

    The Hancheng power plant landslide is a super-scale landslide, which consists of 7 landslides of various sizes. Among them the volume of No. 6 landslide is up to 10,000,000 m/sup 3/. The serious deformations and damages of power plant buildings have been caused by landslide. At present, the landslide is in a condition of slow deformation and creeping. Since the slope angle (30 degrees - 20 degrees) and dip (6 degrees - 8 degrees) of the rock formations are quite gentle, therefore, its movement should be slow all the time and no rapid slipping will occur. The characteristics of the No. 6 landslide mainly are the focus of the analysis and discussion in this paper. The landslide is transformed from the rock formation slipping of slope induced by coal mining beneath Hengshan slope. In this paper, the relationships between occurrence of the landslide and underground coal mining are analysed and proved in detail, and the problems, which should be paid attention to in harnessing the landslide, are put forward. 10 figs.

  14. A practical application of photogrammetry to performing rib characterization measurements in an underground coal mine using a DSLR camera.

    Science.gov (United States)

    Slaker, Brent A; Mohamed, Khaled M

    2017-01-01

    Understanding coal mine rib behavior is important for inferring pillar loading conditions as well as ensuring the safety of miners who are regularly exposed to ribs. Due to the variability in the geometry of underground openings and ground behavior, point measurements often fail to capture the true movement of mine workings. Photogrammetry is a potentially fast, cheap, and precise supplemental measurement tool in comparison to extensometers, tape measures, or laser range meters, but its application in underground coal has been limited. The practical use of photogrammetry was tested at the Safety Research Coal Mine, National Institute for Occupational Safety and Health (NIOSH). A commercially available, digital single-lens reflex (DSLR) camera was used to perform the photogrammetric surveys for the experiment. Several experiments were performed using different lighting conditions, distances to subject, camera settings, and photograph overlaps, with results summarized as follows: the lighting method was found to be insignificant if the scene was appropriately illuminated. It was found that the distance to the subject has a minimal impact on result accuracy, and that camera settings have a significant impact on the photogrammetric quality of images. An increasing photograph resolution was preferable when measuring plane orientations; otherwise a high point cloud density would likely be excessive. Focal ratio (F-stop) changes affect the depth of field and image quality in situations where multiple angles are necessary to survey cleat orientations. Photograph overlap is very important to proper three-dimensional reconstruction, and at least 60% overlap between photograph pairs is ideal to avoid unnecessary post-processing. The suggestions and guidelines proposed are designed to increase the quality of photogrammetry inputs and outputs as well as minimize processing time, and serve as a starting point for an underground coal photogrammetry study.

  15. Developments in the German coal mining industry; Entwicklungen im deutschen Steinkohlenbergbau

    Energy Technology Data Exchange (ETDEWEB)

    Eikhoff, J. [Deutsche Steinkohle AG (DSK), Herne (Germany)

    2007-02-01

    The developments in the German coal mining industry are always associated with the questions of national energy supply. The main emphasis is on a balanced energy mix with the aim of security of supply, compatibility with the environment and profitability. The operating aim of an increase in productivity to reduce costs is derived on this basis. The innovative operation required for this purpose results from the combination of technical, process and social innovation. The two last-mentioned are becoming increasingly important for a high rate of innovation at the collieries of DSK. (orig.)

  16. Methane emissions from coal mining

    International Nuclear Information System (INIS)

    Boyer, C.M.; Kelafant, J.R.; Kuuskraa, V.A.; Manger, K.C.; Kruger, D.

    1990-09-01

    The report estimates global methane emissions from coal mining on a country specific basis, evaluates the technologies available to degasify coal seams and assesses the economics of recovering methane liberated during mining. 33 to 64 million tonnes were liberated in 1987 from coal mining, 75 per cent of which came from China, the USSR, Poland and the USA. Methane emissions from coal mining are likely to increase. Emission levels vary between surface and underground mines. The methane currently removed from underground mines for safety reasons could be used in a number of ways, which may be economically attractive. 55 refs., 19 figs., 24 tabs

  17. Hydrogeology, water chemistry, and subsidence of underground coal mines at Huntsville, Missouri, July 1987 to December 1988. Water Resources Investigation

    International Nuclear Information System (INIS)

    Blevins, D.W.; Ziegler, A.C.

    1992-01-01

    Underground coal mining in and near Huntsville, in Randolph County in north-central Missouri, began soon after 1831. Mining in the Huntsville area was at its peak during 1903 and continued until 1966 when the last underground mine was closed and the economically recoverable coals under Huntsville had been mostly, if not completely, removed. The now abandoned mines are of concern to the public and to various State and Federal agencies for two reasons: (1) mine drainage acidifies streams and leaves large, soft, dangerous deposits of iron oxyhydroxides at mine springs and on streambeds (data on file at the Missouri Department of Natural Resources, Land Reclamation Commission), and (2) collapse of mine cavities sometimes causes surface subsidence resulting in property damage or personal injury. To address these concerns, the U.S. Geological Survey, in cooperation with the Missouri Department of Natural Resources, in 1987 initiated a study to: determine the location of mine springs, the seasonal variation of stream-water chemistry, and the effects of underground-mine water on flow and water quality of nearby ground water and receiving streams; and identify areas susceptible to surface subsidence because of mine collapse. The purpose of the report is to present the findings and data collected for the study

  18. Biomass-derived carbon composites for enrichment of dilute methane from underground coal mines.

    Science.gov (United States)

    Bae, Jun-Seok; Jin, Yonggang; Huynh, Chi; Su, Shi

    2018-07-01

    Ventilation air methane (VAM), which is the main source of greenhouse gas emissions from coal mines, has been a great challenge to deal with due to its huge flow rates and dilute methane levels (typically 0.3-1.0 vol%) with almost 100% humidity. As part of our continuous endeavor to further improve the methane adsorption capacity of carbon composites, this paper presents new carbon composites derived from macadamia nut shells (MNSs) and incorporated with carbon nanotubes (CNTs). These new carbon composites were fabricated in a honeycomb monolithic structure to tolerate dusty environment and to minimize pressure drop. This paper demonstrates the importance of biomass particle size distributions when formed in a composite and methane adsorption capacities at low pressures relevant to VAM levels. The selectivity of methane over nitrogen was about 10.4 at each relevant partial pressure, which was much greater than that (6.5) obtained conventionally (at very low pressures), suggesting that capturing methane in the presence of pre-adsorbed nitrogen would be a practical option. The equilibrium and dynamic performance of biomass-derived carbon composites were enhanced by 30 and 84%, respectively, compared to those of our previous carbon fiber composites. In addition, the presence of moisture in ventilation air resulted in a negligible effect on the dynamic VAM capture performance of the carbon composites, suggesting that our carbon composites have a great potential for site applications at coal mines because the cost and performance of solid adsorbents are critical factors to consider. Copyright © 2018 Elsevier Ltd. All rights reserved.

  19. Investment in the Community coal mining and iron and steel industries - 1981 survey

    Energy Technology Data Exchange (ETDEWEB)

    1982-01-01

    The report has been prepared on the results of the 1981 survey of investments in the Community coal and steel industries. The survey which is conducted annually collects information on actual and forecast capital expenditure and production potential of coal and steel enterprises. The introductory chapter summarizes the results of the survey and the conclusions on them. Subsequent chapters examine in detail the results of the survey for each producing sector, namely: the coal mining industry; coking plants; briquetting plants; iron ore mines; and iron and steel industry. The annex contains a statement of the definitions under which the survey was carried out, together with tables giving a complete analysis of the results of the survey, including tables of capital expenditure and production potential by region and by category of plant for all sectors and categories of coal and steel products falling within the ECSC treaty. Editions are available in the seven community languages.

  20. Investment in the Community coal mining and iron and steel industries - 1980 survey

    Energy Technology Data Exchange (ETDEWEB)

    1980-01-01

    The report has been prepared on the results of the 1980 survey of investments in the Community coal and steel industries. The survey, which is conducted annually, collects information on actual and forecast capital expenditure and production potential of coal and steel enterprises. The introductory chapter summarizes the results of the survey and the conclusions on them. Subsequent chapters of the report examine in detail the results of the survey for each producing sector, namely: the coal mining industry; coking plants; briquetting plants; iron-ore mines; and the iron and steel industry. The annex to the report contains a statement of the definitions under which the survey was carried out, together with tables giving a complete analysis of the results of the survey, including tables of capital expenditure and production potential by region and by category of plant for all sectors and categories of coal and steel products falling within the ECSC Treaty. Editions are available in six community languages.

  1. 'Heat Market Campaign' of the German coal mining industry

    Energy Technology Data Exchange (ETDEWEB)

    Dach, G.

    1983-12-22

    The ''Heat Market Campaign'', presented in June '83 by experts of all fields of coal mining, investigates the possibilities of coal sales promotion. The article reviews the main data of the heat market and discusses the ''Heat Market Campaign'' under the aspects of coal policy and energy policy. The campaign was started with the objectives of energy supply assurance in the Federal Republic of Germany, energy cost reduction on the consumer side, and stabilisation and development of coal markets not affected by the steel crisis. Sales goald on the household, trade and industrial sector are quantified, and obstacles preventing further expansion of the heat market are discussed. Apart from the mining industry's marketing concept for the heat market, there is also the possibility of receiving financial aid by the Federal government.

  2. Highly-productive mechanization systems for coal mining in the Polish coal industry

    Energy Technology Data Exchange (ETDEWEB)

    Sikora, W

    1985-01-01

    Effects of mechanization on underground coal mining in Poland from 1960 to 1980 and mining equipment used in Poland is reviewed. In 1983 black coal output increased to 191.1 Mt. There were 765 working faces, 442 of which with powered supports. Six hundred thirty-four shearer loaders were in use. About 82.7% of coal output fell on faces mined by sets of mining equipment (shearer loaders, powered supports and chain conveyors). The average coal output per working face amounted to 889 t/d. About 50% of mine roadways was driven by heading machines (346 heading machines were in use). The average coal output per face mined by a set of mining equipment amounted to 1248 t/d. About 86% of shearer loaders fell on double drum shearer loaders. Types of mining equipment used in underground mining are reviewed: powered supports (Pioma, Fazos, Glinik and the SOW), shearer loaders (drum shearer loaders and double-drum shearer loaders with chain haulage and chainless haulage systems for unidirectional and bi-directional mining), chain conveyors (Samson, Rybnik). Statistical data on working faces with various sets of equipment are given. 3 references.

  3. An Information Framework for Facilitating Cost Saving of Environmental Impacts in the Coal Mining Industry in South Africa

    Directory of Open Access Journals (Sweden)

    Mashudu D. Mbedzi

    2018-05-01

    Full Text Available Coal-mining contributes much to the economic welfare of a country. Yet it brings along a number of challenges, notably environmental impacts which include water pollution in a water scarce country such as South Africa. This research is conducted in two phases. The first phase intends to establish environmental and other challenges brought about by the coal-mining industry through a comprehensive analysis of available literature. Combatting these challenges is costly; consequently, our work investigates how established management accounting tools and techniques such as Environmental Management Accounting (EMA, Material Flow Cost Accounting (MFCA and Life Cycle Costing (LCC may facilitate cost savings for the companies involved. These techniques promote increased transparency of material usage by tracing and quantifying the flows and inventories of materials within the coal-mining industry in physical and monetary terms, hence hidden costs are elicited. The researchers postulate that an Information Framework integrating these aspects may be the way forward. To this end existing frameworks in the literature are identified. A number of research questions embodying the above aspects are defined and the objective is to define a conceptual framework to facilitate cost savings for coal-mining companies. The main contribution of this work is an information framework presented towards the end of this article. The second phase of the research will involve fieldwork in the form of a survey among stakeholders in industry to validate the conceptual framework.

  4. Feasibility of CO2 Sequestration as a Closure Option for Underground Coal Mine

    Science.gov (United States)

    Ray, Sutapa; Dey, Kaushik

    2018-01-01

    The Kyoto Protocol, 1998, was signed by member countries to reduce greenhouse gas (GHG) emissions to a minimum acceptable level. India agreed to Kyoto Protocol since 2002 and started its research on GHG mitigation. Few researchers have carried out research work on CO2 sequestration in different rock formations. However, CO2 sequestration in abandoned mines has yet not drawn its attention largely. In the past few years or decades, a significant amount of research and development has been done on Carbon Capture and Storage (CCS) technologies, since it is a possible solution for assuring less emission of CO2 to the atmosphere from power plants and some other major industrial plants. CCS mainly involves three steps: (a) capture and compression of CO2 from source (power plants and industrial areas), (b) transportation of captured CO2 to the storage mine and (c) injecting CO2 into underground mine. CO2 is stored at an underground mine mainly in three forms: (1) adsorbed in the coals left as pillars of the mine, (2) absorbed in water through a chemical process and (3) filled in void with compressed CO2. Adsorption isotherm is a graph developed between the amounts of adsorbate adsorbed on the surface of adsorbent and the pressure at constant temperature. Various types of adsorption isotherms are available, namely, Freundlich, Langmuir and BET theory. Indian coal is different in origin from most of the international coal deposits and thus demands isotherm experiments of the same to arrive at the right adsorption isotherm. To carry out these experiments, adsorption isotherm set up is fabricated in the laboratory with a capacity to measure the adsorbed volume up to a pressure level of 100 bar. The coal samples are collected from the pillars and walls of the underground coal seam using a portable drill machine. The adsorption isotherm experiments have been carried out for the samples taken from a mine. From the adsorption isotherm experiments, Langmuir Equation is found to be

  5. Feasibility of CO2 Sequestration as a Closure Option for Underground Coal Mine

    Science.gov (United States)

    Ray, Sutapa; Dey, Kaushik

    2018-04-01

    The Kyoto Protocol, 1998, was signed by member countries to reduce greenhouse gas (GHG) emissions to a minimum acceptable level. India agreed to Kyoto Protocol since 2002 and started its research on GHG mitigation. Few researchers have carried out research work on CO2 sequestration in different rock formations. However, CO2 sequestration in abandoned mines has yet not drawn its attention largely. In the past few years or decades, a significant amount of research and development has been done on Carbon Capture and Storage (CCS) technologies, since it is a possible solution for assuring less emission of CO2 to the atmosphere from power plants and some other major industrial plants. CCS mainly involves three steps: (a) capture and compression of CO2 from source (power plants and industrial areas), (b) transportation of captured CO2 to the storage mine and (c) injecting CO2 into underground mine. CO2 is stored at an underground mine mainly in three forms: (1) adsorbed in the coals left as pillars of the mine, (2) absorbed in water through a chemical process and (3) filled in void with compressed CO2. Adsorption isotherm is a graph developed between the amounts of adsorbate adsorbed on the surface of adsorbent and the pressure at constant temperature. Various types of adsorption isotherms are available, namely, Freundlich, Langmuir and BET theory. Indian coal is different in origin from most of the international coal deposits and thus demands isotherm experiments of the same to arrive at the right adsorption isotherm. To carry out these experiments, adsorption isotherm set up is fabricated in the laboratory with a capacity to measure the adsorbed volume up to a pressure level of 100 bar. The coal samples are collected from the pillars and walls of the underground coal seam using a portable drill machine. The adsorption isotherm experiments have been carried out for the samples taken from a mine. From the adsorption isotherm experiments, Langmuir Equation is found to be

  6. A Critical Study on the Underground Environment of Coal Mines in India-an Ergonomic Approach

    Science.gov (United States)

    Dey, Netai Chandra; Sharma, Gourab Dhara

    2013-04-01

    Ergonomics application on underground miner's health plays a great role in controlling the efficiency of miners. The job stress in underground mine is still physically demanding and continuous stress due to certain posture or movement of miners during work leads to localized muscle fatigue creating musculo-skeletal disorders. A good working environment can change the degree of job heaviness and thermal stress (WBGT values) can directly have the effect on stretch of work of miners. Out of many unit operations in underground mine, roof bolting keeps an important contribution with regard to safety of the mine and miners. Occupational stress of roof bolters from ergonomic consideration has been discussed in the paper.

  7. Methane emissions from coal mining

    International Nuclear Information System (INIS)

    Williams, A.; Mitchell, C.

    1993-01-01

    This paper outlines some of the problems associated with the prediction of levels of methane emission from underground and surface coal mines. Current knowledge of coal mining emissions sources is outlined. On the basis of this information the methodology proposed by the IPCC/OECD Programme on National Inventories is critically examined and alternatives considered. Finally, the technical options for emissions control are examined together with their feasibility. 8 refs., 6 figs., 2 tabs

  8. In situ monitoring of primary roofbolts at underground coal mines in the USA

    OpenAIRE

    Spearing, A.J.S.; Hyett, A.

    2014-01-01

    Primary roof support represents the first line of defence against rock-related falls of ground in underground mines, and improper utilization or misunderstanding of the applicability and behaviour of primary support can be costly from a safety standpoint. This is a major concern for underground mines, as roof support is the single most costly expense from a mining operational perspective. This is further backed by the evidence that, in the USA, hundreds of injuries and fatalities still occur ...

  9. Investigation into the potential for dust and gas explosions in underground coal mines with reference to pick tip geometry

    International Nuclear Information System (INIS)

    Dawood, Albert D.

    2011-01-01

    In underground coal mines, methane gas, if present in sufficient concentration, may be ignited by sparks from hot spots on the picks of coal cutting machines striking hard bands of rock. During the coal cutting, wear-flat areas develop on the trailing side of the tips of picks. As pick wear progresses, the generation of frictional heat and coal dust increases and the development of hot spots at the cutting tips may lead to an explosion of methane gas. Field experience and research work over the last few years have facilitated excellent cutting performance for certain picks through the optimisation of the cutting parameters. Such performance improvements show great promise in preventing the incidence of gas or dust explosions occurring at the coal face area. This study sets out some of the fundamentals of pick geometry and cutting parameters and the methods which have been employed to achieve improvements in reducing the hazards of gas or dust explosions. It is based on the comparative trial results of two types of picks with different designs and on a range of available research information on the subject. My investigation looked at the fundamentals of pick geometry and cutting parameters and the current suppression techniques in place to control the dust and gas explosions on the coal operating face.

  10. An injection technique for in-situ remediation of abandoned underground coal mines

    International Nuclear Information System (INIS)

    Canty, G.A.; Everett, J.W.

    1998-01-01

    Remediation of underground mines can prove to be a difficult task, given the physical constraints associated with introducing amendments to a subterranean environment. An acid mine abatement project involving in-situ chemical treatment method was conducted by the University of Oklahoma. The treatment method involved the injection of an alkaline coal combustion by-product (CCB) slurry into a flooded mine void (pH 4.4) to create a buffered zone. Injection of the CCB slurry was possible through the use of equipment developed by the petroleum industry for grouting recovery wells. This technology was selected because the CCB slurry could be injected under significant pressure and at a high rate. With higher pressure and rates of injection, a large quantity of slurry can be introduced into the mine within a limited amount of time. Theoretically, the high pressure and rate would improve dispersal of the slurry within the void. In addition, the high pressure is advantageous in fracturing or breaking-down obstructions to injection. During the injection process, a total of 418 tons of CCB was introduced within 15 hours. The mine did not refuse any of the material, and it is likely that a much larger mass could have been added. One injection well was drilled into a pillar of coal. Normally this would pose a problem when introducing a slurry; however, the coal pillar was easily fractured during the injection process. Currently, the pH of the mine discharge is above 6.5 and the alkalinity is approximately 100 mg/L as CACO 3

  11. Evaluation of water resources around Barapukuria coal mine industrial area, Dinajpur, Bangladesh

    Science.gov (United States)

    Howladar, M. Farhad; Deb, Pulok Kanti; Muzemder, A. T. M. Shahidul Huqe; Ahmed, Mushfique

    2014-09-01

    Water is a very important natural resource which can be utilized in renewable or non-renewable forms but before utilizing, the evaluation of the quality of this resource is crucial for a particular use. However, the problems of water quality are more severe in areas where the mining and mineral processes' industries are present. In mining processes, several classes of wastes are produced which may turn into ultimately the sources of water quality and environmental degradation. In consequences, the evaluations of water quality for livestock, drinking, irrigation purposes and environmental implications have been carried out around the Barapukuria Coal Mining Industry under different methods and techniques such as primarily the field investigation; secondly the laboratory chemical analysis and thirdly justified the suitability of the laboratory analysis with statistical representation and correlation matrix, Schoeller plot, Piper's Trilinear diagram, Expanded Durov diagram, Wilcox diagram, US salinity diagram, Doneen's chart and others. The results of all surface and ground water samples analysis show that the characteristics and concentrations of all the major physical and chemical parameters such as pH, EC, TDS, Na+, K+, Ca2+, Mg2+, Fetotal, Cl-, HCO3 -, CO3 2- and SO4 2- are varied from one sample to other but well analogous with the WHO and EQS standard limit for all purposes in the area where the abundance of the major ions is as follows: Ca2+ > Na+ > Mg2+ > K+ > Fetotal = HCO3 - > SO4 2- > Cl- > CO3 2-. The graphical exposition of analytical data demonstrates two major hydrochemical facies for example: calcium-bicarbonate (Ca2+- HCO3 -) and magnesium-bicarbonate (Mg2+- HCO3 -) type facies which directly support the shallow recently recharged alkaline water around the industry. The calculated values for the evaluation classification of water based on TDS, Na%, EC, SAR, PI, RSC, MH, and TH replicate good to excellent use of water for livestock, drinking and

  12. An analysis of workers' morale in the coal mining industry using principal component analysis

    Energy Technology Data Exchange (ETDEWEB)

    Armstrong, J; La Court, C; Pearson, J M

    1987-03-01

    This paper looks at labour morale in the coal mining industry from 1967 to 1984. In particular it examines absenteeism, turnover and accidents over that period, as well as constructing an index of morale based on these variables. The data are taken from the North Nottinghamshire and South Yorkshire coal areas, and a comparison is made between these areas in the period leading up to the industrial action in 1984/85. The indices constructed indicate that morale, as measured by the first principal component, increased considerably during the years before the 1984 industrial dispute and that low morale was an unlikely reason for the dispute, although morale in South Yorkshire, a strike area, was lower than in North Nottinghamshire, largely a non-strike area. The steep rise in morale in both North Nottinghamshire and South Yorkshire follows closely the rise in unemployment nationally and may simply be an indication of conventional industrial relations assumptions that manifestations of negative worker attitudes are greatest when jobs are relatively plentiful, and considerably less so when jobs are scarce.

  13. An analysis of workers' morale in the coal mining industry using principal component analysis

    Energy Technology Data Exchange (ETDEWEB)

    Armstrong, J.; La Court, C.; Pearson, J.M.

    1987-03-01

    This paper looks at labour morale in the coal mining industry from 1967 to 1984. In particular it examines absenteeism, turnover and accidents over that period, as well as constructing an index of morale based on these variables. The data are taken from the North Nottinghamshire and South Yorkshire coal areas, and a comparison is made between these areas in the period leading up to the industrial action in 1984/85. The indices constructed indicate that morale, as measured by the first principal component, increased considerably during the years before the 1984 industrial dispute and that low morale was an unlikely reason for the dispute, although morale in South Yorkshire, a strike area, was lower than in North Nottinghamshire, largely a non-strike area. The steep rise in morale in both North Nottinghamshire and South Yorkshire follows closely the rise in unemployment nationally and may simply be an indication of conventional industrial relations assumptions that manifestations of negative worker attitudes are greatest when jobs are relatively plentiful, and considerably less so when jobs are scarce.

  14. Study on the Effect of Frequency on Conductivity of Underground Strata in Coal Mine Through-the-earth Wireless Communication

    OpenAIRE

    Jinyi TAO; Yuchen ZHANG

    2014-01-01

    The relationship of conductivity and the frequency, which is of decisive significance in through-the-earth wireless communication in coal mine, is closely related to the options of frequency range in coal mine wireless communication. When through-the-earth wireless communication is applied, the electromagnetic waves need to spread in the semi-conductive medium rocks. The main factors affecting the electromagnetic wave propagation in rocks is the rock strata electromagnetic parameters. These p...

  15. Coal mining in Australia

    Energy Technology Data Exchange (ETDEWEB)

    Mills, L J

    1981-12-01

    In 1959 black coal production in Australia totalled some 21.9 million tonnes per annum, 70% of this being produced from underground mines in the coalfields of New South Wales. By 1980 output levels had increased by nearly 350% to 75.4 million tonnes per annum (54% of which was exported) compared with 5% some 20 years earlier. Because it is blessed with large reserves of coal and other forms of energy, it is inevitable that the Australian coal mining industry will be required to play a major role in the development of the international coal market through to the end of the present century. Experts now predict a need for the black coal output in Australia to be developed from its present level to a minimum of 293 million tonnes per annum by the year 2000. This paper examines the present circumstances in the Australian coal industry and attempts to outline the development which has to be undertaken in order to meet the needs of an energy hungry world.

  16. 100 years of the main mine rescue service. A contribution to the protection against disasters in the coal mining industry; 100 Jahre Hauptstelle fuer das Grubenrettungswesen. Ein Beitrag zum Katastrophenschutz im Steinkohlenbergbau

    Energy Technology Data Exchange (ETDEWEB)

    Hermuelheim, Walter [RAG Aktiengesellschaft, Herne (Germany). Zentralbereich Arbeits-, Gesundheits- und Umweltschutz

    2011-06-15

    A review of 100 years of protection against disasters in the coal mining industry impressively shows the way from an era of major accidents to a modern branch of industry, which justifiably and with good prospects of success can pursue the aim of ''No accidents - no damage to health - no damage to the environment''. However, the development of the mine rescue service over more than 100 years - represented in the Ruhr by the Main Mine Rescue Service established in 1910 in Essen - would be incomplete without consideration of the allied technical fields underground fire protection and explosion protection. Cooperation between institutions such as the Tremonia test mine and the BVG has produced a safety level in all three fields, which is regarded as exemplary worldwide, and in addition to the latest mining technology is a good advertisement for the German coal mining industry. (orig.)

  17. Analysis on the Initial Cracking Parameters of Cross-Measure Hydraulic Fracture in Underground Coal Mines

    Directory of Open Access Journals (Sweden)

    Yiyu Lu

    2015-07-01

    Full Text Available Initial cracking pressure and locations are important parameters in conducting cross-measure hydraulic fracturing to enhance coal seam permeability in underground coalmines, which are significantly influenced by in-situ stress and occurrence of coal seam. In this study, stress state around cross-measure fracturing boreholes was analyzed using in-situ stress coordinate transformation, then a mathematical model was developed to evaluate initial cracking parameters of borehole assuming the maximum tensile stress criterion. Subsequently, the influences of in-situ stress and occurrence of coal seams on initial cracking pressure and locations in underground coalmines were analyzed using the proposed model. Finally, the proposed model was verified with field test data. The results suggest that the initial cracking pressure increases with the depth cover and coal seam dip angle. However, it decreases with the increase in azimuth of major principle stress. The results also indicate that the initial cracking locations concentrated in the second and fourth quadrant in polar coordinate, and shifted direction to the strike of coal seam as coal seam dip angle and azimuth of maximum principle stress increase. Field investigation revealed consistent rule with the developed model that the initial cracking pressure increases with the coal seam dip angle. Therefore, the proposed mathematical model provides theoretical insight to analyze the initial cracking parameters during cross-measure hydraulic fracturing for underground coalmines.

  18. Development and application of the Safe Performance Index as a risk-based methodology for identifying major hazard-related safety issues in underground coal mines

    Science.gov (United States)

    Kinilakodi, Harisha

    The underground coal mining industry has been under constant watch due to the high risk involved in its activities, and scrutiny increased because of the disasters that occurred in 2006-07. In the aftermath of the incidents, the U.S. Congress passed the Mine Improvement and New Emergency Response Act of 2006 (MINER Act), which strengthened the existing regulations and mandated new laws to address the various issues related to a safe working environment in the mines. Risk analysis in any form should be done on a regular basis to tackle the possibility of unwanted major hazard-related events such as explosions, outbursts, airbursts, inundations, spontaneous combustion, and roof fall instabilities. One of the responses by the Mine Safety and Health Administration (MSHA) in 2007 involved a new pattern of violations (POV) process to target mines with a poor safety performance, specifically to improve their safety. However, the 2010 disaster (worst in 40 years) gave an impression that the collective effort of the industry, federal/state agencies, and researchers to achieve the goal of zero fatalities and serious injuries has gone awry. The Safe Performance Index (SPI) methodology developed in this research is a straight-forward, effective, transparent, and reproducible approach that can help in identifying and addressing some of the existing issues while targeting (poor safety performance) mines which need help. It combines three injury and three citation measures that are scaled to have an equal mean (5.0) in a balanced way with proportionate weighting factors (0.05, 0.15, 0.30) and overall normalizing factor (15) into a mine safety performance evaluation tool. It can be used to assess the relative safety-related risk of mines, including by mine-size category. Using 2008 and 2009 data, comparisons were made of SPI-associated, normalized safety performance measures across mine-size categories, with emphasis on small-mine safety performance as compared to large- and

  19. Finite element modeling of surface subsidence induced by underground coal mining

    International Nuclear Information System (INIS)

    Su, D.W.H.

    1992-01-01

    The ability to predict the effects of longwall mining on topography and surface structures is important for any coal company in making permit applications and anticipating potential mining problems. The sophisticated finite element model described and evaluated in this paper is based upon five years of underground and surface observations and evolutionary development of modeling techniques and attributes. The model provides a very powerful tool to address subsidence and other ground control questions. The model can be used to calculate postmining stress and strain conditions at any horizon between the mine and the ground surface. This holds the promise of assisting in the prediction of mining-related hydrological effects

  20. Coal mine subsidence

    International Nuclear Information System (INIS)

    Rahall, N.J.

    1991-05-01

    This paper examines the efficacy of the Department of the Interior's Office of Surface Mining Reclamation and Enforcement's (OSMRE) efforts to implement the federally assisted coal mine subsidence insurance program. Coal mine subsidence, a gradual settling of the earth's surface above an underground mine, can damage nearby land and property. To help protect property owners from subsidence-related damage, the Congress passed legislation in 1984 authorizing OSMRE to make grants of up to $3 million to each state to help the states establish self-sustaining, state-administered insurance programs. Of the 21 eligible states, six Colorado, Indiana, Kentucky, Ohio, West Virginia, and Wyoming applied for grants. This paper reviews the efforts of these six states to develop self-sustaining insurance programs and assessed OSMRE's oversight of those efforts

  1. Multi-Sensor Detection with Particle Swarm Optimization for Time-Frequency Coded Cooperative WSNs Based on MC-CDMA for Underground Coal Mines

    Directory of Open Access Journals (Sweden)

    Jingjing Xu

    2015-08-01

    Full Text Available In this paper, a wireless sensor network (WSN technology adapted to underground channel conditions is developed, which has important theoretical and practical value for safety monitoring in underground coal mines. According to the characteristics that the space, time and frequency resources of underground tunnel are open, it is proposed to constitute wireless sensor nodes based on multicarrier code division multiple access (MC-CDMA to make full use of these resources. To improve the wireless transmission performance of source sensor nodes, it is also proposed to utilize cooperative sensors with good channel conditions from the sink node to assist source sensors with poor channel conditions. Moreover, the total power of the source sensor and its cooperative sensors is allocated on the basis of their channel conditions to increase the energy efficiency of the WSN. To solve the problem that multiple access interference (MAI arises when multiple source sensors transmit monitoring information simultaneously, a kind of multi-sensor detection (MSD algorithm with particle swarm optimization (PSO, namely D-PSO, is proposed for the time-frequency coded cooperative MC-CDMA WSN. Simulation results show that the average bit error rate (BER performance of the proposed WSN in an underground coal mine is improved significantly by using wireless sensor nodes based on MC-CDMA, adopting time-frequency coded cooperative transmission and D-PSO algorithm with particle swarm optimization.

  2. Multi-Sensor Detection with Particle Swarm Optimization for Time-Frequency Coded Cooperative WSNs Based on MC-CDMA for Underground Coal Mines.

    Science.gov (United States)

    Xu, Jingjing; Yang, Wei; Zhang, Linyuan; Han, Ruisong; Shao, Xiaotao

    2015-08-27

    In this paper, a wireless sensor network (WSN) technology adapted to underground channel conditions is developed, which has important theoretical and practical value for safety monitoring in underground coal mines. According to the characteristics that the space, time and frequency resources of underground tunnel are open, it is proposed to constitute wireless sensor nodes based on multicarrier code division multiple access (MC-CDMA) to make full use of these resources. To improve the wireless transmission performance of source sensor nodes, it is also proposed to utilize cooperative sensors with good channel conditions from the sink node to assist source sensors with poor channel conditions. Moreover, the total power of the source sensor and its cooperative sensors is allocated on the basis of their channel conditions to increase the energy efficiency of the WSN. To solve the problem that multiple access interference (MAI) arises when multiple source sensors transmit monitoring information simultaneously, a kind of multi-sensor detection (MSD) algorithm with particle swarm optimization (PSO), namely D-PSO, is proposed for the time-frequency coded cooperative MC-CDMA WSN. Simulation results show that the average bit error rate (BER) performance of the proposed WSN in an underground coal mine is improved significantly by using wireless sensor nodes based on MC-CDMA, adopting time-frequency coded cooperative transmission and D-PSO algorithm with particle swarm optimization.

  3. Effects on Buildings of Surface Curvature Caused by Underground Coal Mining

    Directory of Open Access Journals (Sweden)

    Haifeng Hu

    2016-08-01

    Full Text Available Ground curvature caused by underground mining is one of the most obvious deformation quantities in buildings. To study the influence of surface curvature on buildings and predict the movement and deformation of buildings caused by ground curvature, a prediction model of the influence function on mining subsidence was used to establish the relationship between surface curvature and wall deformation. The prediction model of wall deformation was then established and the surface curvature was obtained from mining subsidence prediction software. Five prediction lines were set up in the wall from bottom to top and the predicted deformation of each line was used to calculate the crack positions in the wall. Thus, the crack prediction model was obtained. The model was verified by a case study from a coalmine in Shanxi, China. The results show that when the ground curvature is positive, the crack in the wall is shaped like a “V”; when the ground curvature is negative, the crack is shaped like a “∧”. The conclusion provides the basis for a damage evaluation method for buildings in coalmine areas.

  4. Water quality changes of a closed underground coal mine in Korea.

    Science.gov (United States)

    Cheong, Young Wook; Yim, Gil-Jae; Ji, Sang Woo; Kang, Sang Soo; Skousen, Jeffery

    2012-01-01

    The objective of this study was to assess the changes in mine water quality as an underground mine flooded from July 2005 to October 2008. The effect of air injection with a blower into the water was used to evaluate the potential to convert ferrous to ferric iron and to provide in situ treatment and precipitation. Mine flooding averaged 31 cm/day with a linear shape until November 2007, when it flattened out due to outflow. During flooding, mine water pH remained around 6, but Eh shifted from 200 to -150 mV. After the mine water level stabilized, contents of elements such as Fe and SO(4) tended to decrease as time passed. Air was injected by diffusers (150 L/min/each) at three different depths of 2, 3, and 5 m below the water level in the shaft. Dissolved oxygen eventually increased to 4 or 5 mg/L depending on the depth of the diffusers. Aeration caused conversion of ferrous iron to ferric iron and about 30 mg/l of iron was removed from the mine water. Therefore, air injection shows potential as a semi-active treatment or part of conventional treatment to precipitate iron in the mine pool.

  5. Means to improve underground coal mine safety by automated control of methane drainage systems

    Directory of Open Access Journals (Sweden)

    Babut Gabriel Bujor

    2017-01-01

    Full Text Available Based on the critical analysis of the presently employed management of methane drainage systems operation in Jiu Valley collieries, the paper aims to assess the basic elements required to develop an automated monitoring and control system of these. The results obtained after studies and researches carried out also allowed formulating certain proposals regarding the modification of manual control procedures of methane drainage systems operation, in order to correlate them with the prescriptions of legislation requirements from countries having a well-developed mining industry. Putting in practice the mentioned proposals could have immediate and beneficial effects on increasing the methane drainage process efficiency, leading meanwhile to an improved working environment and, implicitly, to a higher level of occupational safety and health in Jiu Valley collieries.

  6. Application of ERTS-1 imagery to fracture related mine safety hazards in the coal mining industry. [Indiana

    Science.gov (United States)

    Wier, C. E.; Wobber, F. J. (Principal Investigator); Russell, O. R.; Amato, R. V.; Leshendok, T. V.

    1974-01-01

    The author has identified the following significant results. New fracture detail of Indiana has been observed and mapped from ERTS-1 imagery. Studies so far indicate a close relationship between the directions of fracture traces mapped from the imagery, fractures measured on bedrock outcrops, and fractures measured in the underground mines. First hand observations and discussions with underground mine operators indicate good correlation of mine hazard maps prepared from ERTS-1/aircraft imagery and actual roof falls. The inventory of refuse piles/slurry ponds of the coal field of Indiana has identified over 225 such sites from past mining operations. These data will serve the State Legislature in making tax decisions on coal mining which take on increased importance because of the energy crisis.

  7. Methane in German hard coal mining

    International Nuclear Information System (INIS)

    Martens, P.N.; Den Drijver, J.

    1995-01-01

    Worldwide, hard coal mining is being carried out at ever increasing depth, and has, therefore, to cope with correspondingly increasing methane emissions are caused by coal mining. Beside carbon dioxide, chloro-fluoro-carbons (CFCs) and nitrogen oxides, methane is one of the most significant 'greenhouse' gases. It is mainly through the release of such trace gases that the greenhouse effect is brought about. Reducing methane emissions is therefore an important problem to be solved by the coal mining industry. This paper begins by highlighting some of the fundamental principles of methane in hard coal mining. The methane problem in German hard coal mining and the industry's efforts to reduce methane emissions are presented. The future development in German hard coal mining is illustrated by an example which shows how large methane volumes can be managed, while still maintaining high outputs at increasing depth. (author). 7 tabs., 10 figs., 20 refs

  8. 30 CFR 817.87 - Coal mine waste: Burning and burned waste utilization.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: Burning and burned waste...-UNDERGROUND MINING ACTIVITIES § 817.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or unburned coal mine waste shall be removed from a permitted disposal...

  9. The coal mining industry in Vietnam and its challenges; Steinkohlenbergbau in Vietnam und seine Herausforderungen

    Energy Technology Data Exchange (ETDEWEB)

    Martens, Per Nicolai; Pateiro Fernandez, Jose B.; Ahmad, Shakeel [RWTH Aachen (Germany). Inst. fuer Bergbaukunde I; Cramer, Thomas; Deissmann, Guido [Brenk Systemplanung GmbH, Aachen (Germany); Fuchsschwanz, Marcus [RWTH Aachen (Germany). Lehrstuhl fuer Geotechnik

    2010-04-15

    The province of Quang Ninh in the north of Vietnam is the most important coal mining region in the country. The NBCC (Nui Beo Coal Company) operates several open-cast mines. Large quantities of overburden have to be removed and dumped in the immediate environment. The creation of these heaps up to 300 m high is accompanied by many environmental problems. In particular ground and surface waters are contaminated by ''acid mine drainage''. Furthermore, large emissions chiefly in the form of dust occur as a result of the working and dumping depending on the season. In addition the stability of the heaps is sometimes greatly endangered. In the German-Vietnamese Research Association Mining and Environment in Vietnam (RAME) the aspects of coal mining with an effect on the environment are dealt with in various sub-associations and protective measures worked out jointly. (orig.)

  10. THE DASHBOARD - STRATEGIC MANAGEMENT TOOL OF ACTIVITIES IN THE COAL MINING INDUSTRY

    Directory of Open Access Journals (Sweden)

    DINA IONELA-CLAUDIA

    2014-02-01

    Full Text Available In order to achieve the objectives at all levels and categories of functions in the unit, use multiple information systems, including the dashboard which is one of the management tools that responds very well to the rationale and supporting data of management decisions complementary to those provided by other media. In this respect, we try to calculate indicators organization currently working compartments of the coal mining units and will propose a series of indicators whose calculation we consider would be necessary for a detailed presentation as activity carried out and the improvement of management.

  11. Large blastholes in coal mining, canal effects. Barrenos largos en la mineria del carbon, efecto canal

    Energy Technology Data Exchange (ETDEWEB)

    Muniz Hevia, E.; Legorburu Zuazva, V.; Blanco Gonzalez, R. (Union Explosivos Rio Tinto SA, Madrid (Spain))

    1988-01-01

    The 'canal effect' has been known for a long time. It appears only in underground workings. It may be said that the coal industry has suffered from it less than other sectors, perhaps because of its rigorous safety legislation. The Spanish coal mining industry has now been without this phenomenon for many years. 3 refs., 3 figs.

  12. Development a solid state sensor based on SnO_2 nanoparticles for underground coal mine methane detection using zeolites as filter

    International Nuclear Information System (INIS)

    Abruzzi, R.C.; Dedavid, B.A.; Pires, M.J.R.; Luvizon, N.S.

    2016-01-01

    Aiming the monitoring of methane (CH_4) in underground coal mines, the tin oxide (SnO_2) was synthesis and applied to the development of a MOS sensor (metal oxide semiconductor). Zeolite have been tested as a filter of carbon dioxide (CO_2) to ensure the selectivity in the detection of CH_4. Analysis of Transmission Electron Microscopy (TEM) and X-Ray Diffraction (XRD) indicated a synthesis of nanoscaled structures. The energy band gap showed characteristic values for a potential application of SnO_2 in CH_4 sensors. Analysis of surface area by BET isotherms showed high values for the zeolite 13X and Y, while adsorption tests indicated that the zeolite 13X presents greater adsorption efficiency of CO_2. The sputtering technique for deposition of the electrodes, as well as the method of drop coating for deposition of SnO_2, proved effective in developing the sensor. (author)

  13. The Contribution of Individual, Social and Work Characteristics to Employee Mental Health in a Coal Mining Industry Population.

    Directory of Open Access Journals (Sweden)

    Robyn Considine

    Full Text Available Evidence regarding the extent of mental health problems and the associated characteristics within an employee population is necessary to inform appropriate and tailored workplace mental health programs. Mental health within male dominated industries (such as mining has received recent public attention, chiefly through observations regarding suicide in such populations in Australia and internationally. Currently there is limited empirical evidence regarding the mental health needs in the mining industry as an exemplar of a male dominated workforce, and the relative contribution to such problems of individual, socio-economic and workplace factors. This study aimed to investigate the mental health and associated characteristics among employees in the Australian coal mining industry with a specific focus on identifying modifiable work characteristics.A cross-sectional study was conducted among employees (n = 1457 across eight coal mines stratified by key mine characteristics (state, mine type and employee commute arrangements. Participants completed measures of psychological distress (K10+ and key variables across four categories (socio-demographic characteristics, health history, current health behaviours, work attitudes and characteristics.Psychological distress levels within this sample were significantly higher in comparison with a community sample of employed Australians. The following factors contributed significantly to levels of psychological distress using hierarchical linear regression analysis: lower social networks; a past history of depression, anxiety or drug/alcohol problems; high recent alcohol use; work role (managers and a set of work characteristics (level of satisfaction with work, financial factors and job insecurity; perception of lower workplace support for people with mental health problems.This is the first study to examine the characteristics associated with mental health problems in the Australian coal mining industry. The

  14. The Contribution of Individual, Social and Work Characteristics to Employee Mental Health in a Coal Mining Industry Population.

    Science.gov (United States)

    Considine, Robyn; Tynan, Ross; James, Carole; Wiggers, John; Lewin, Terry; Inder, Kerry; Perkins, David; Handley, Tonelle; Kelly, Brian

    2017-01-01

    Evidence regarding the extent of mental health problems and the associated characteristics within an employee population is necessary to inform appropriate and tailored workplace mental health programs. Mental health within male dominated industries (such as mining) has received recent public attention, chiefly through observations regarding suicide in such populations in Australia and internationally. Currently there is limited empirical evidence regarding the mental health needs in the mining industry as an exemplar of a male dominated workforce, and the relative contribution to such problems of individual, socio-economic and workplace factors. This study aimed to investigate the mental health and associated characteristics among employees in the Australian coal mining industry with a specific focus on identifying modifiable work characteristics. A cross-sectional study was conducted among employees (n = 1457) across eight coal mines stratified by key mine characteristics (state, mine type and employee commute arrangements). Participants completed measures of psychological distress (K10+) and key variables across four categories (socio-demographic characteristics, health history, current health behaviours, work attitudes and characteristics). Psychological distress levels within this sample were significantly higher in comparison with a community sample of employed Australians. The following factors contributed significantly to levels of psychological distress using hierarchical linear regression analysis: lower social networks; a past history of depression, anxiety or drug/alcohol problems; high recent alcohol use; work role (managers) and a set of work characteristics (level of satisfaction with work, financial factors and job insecurity; perception of lower workplace support for people with mental health problems. This is the first study to examine the characteristics associated with mental health problems in the Australian coal mining industry. The findings

  15. Identifying sources of respirable quartz and silica dust in underground coal mines in southern West Virginia, western Virginia, and eastern Kentucky

    Energy Technology Data Exchange (ETDEWEB)

    Schatzel, Steven J. [National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, 626 Cochrans Mill Road, PO Box 18070, Pittsburgh, PA 15236 (United States)

    2009-04-01

    Prior research has suggested that the source of respirable silica dust in underground coal mines is typically the immediate top or bottom lithology adjacent to the mined seam, not mineral matter bound within the mined coal bed. Geochemical analyses were applied in an effort to identify the specific source rock of respirable quartz dust in coal mines. The analyses also demonstrate the compositional changes that take place in the generation of the respirable dust fraction from parent rock material. All six mine sites were mining coal with relatively low mineral matter content, although two mines were operating in the Fire Clay coal bed which contains a persistent tonstein. Interpretations of Ca, Mg, Mn, Na, and K concentrations strongly suggest that the top strata above the mined seam is the primary source of mineral dust produced during mining. One site indicates a mixed or bottom source, possibly due to site specific conditions. Respirable dust compositional analyses suggest a direct relationship between the quantity of mineral Si and the quantity of quartz Si. A similar relationship was not found in either the top or bottom rocks adjacent to the mined seam. An apparent loss of elemental Al was noted in the respirable dust fraction when compared to potential parent rock sources. Elemental Al is present in top and bottom rock strata within illite, kaolinite, feldspar, and chlorite. A possible explanation for loss of Al in the respirable dust samples is the removal of clays and possibly chlorite minerals. It is expected that removal of this portion of the Al bearing mineral matter occurs during rock abrasion and dust transport prior to dust capture on the samplers. (author)

  16. Application of underground microseismic monitoring for ground failure and secure longwall coal mining operation: A case study in an Indian mine

    Science.gov (United States)

    Ghosh, G. K.; Sivakumar, C.

    2018-03-01

    Longwall mining technique has been widely used around the globe due to its safe mining process. However, mining operations are suspended when various problems arise like collapse of roof falls, cracks and fractures propagation in the roof and complexity in roof strata behaviors. To overcome these colossal problems, an underground real time microseismic monitoring technique has been implemented in the working panel-P2 in the Rajendra longwall underground coal mine at South Eastern Coalfields Limited (SECL), India. The target coal seams appears at the panel P-2 within a depth of 70 m to 76 m. In this process, 10 to 15 uniaxial geophones were placed inside a borehole at depth range of 40 m to 60 m located over the working panel-P2 with high rock quality designation value for better seismic signal. Various microseismic events were recorded with magnitude ranging from -5 to 2 in the Richter scale. The time-series processing was carried out to get various seismic parameters like activity rate, potential energy, viscosity rate, seismic moment, energy index, apparent volume and potential energy with respect to time. The used of these parameters helped tracing the events, understanding crack and fractures propagation and locating both high and low stress distribution zones prior to roof fall occurrence. In most of the cases, the events were divided into three stage processes: initial or preliminary, middle or building, and final or falling. The results of this study reveal that underground microseismic monitoring provides sufficient prior information of underground weighting events. The information gathered during the study was conveyed to the mining personnel in advance prior to roof fall event. This permits to take appropriate action for safer mining operations and risk reduction during longwall operation.

  17. Recent advances in remote coal mining machine sensing, guidance, and teleoperation

    Energy Technology Data Exchange (ETDEWEB)

    Ralston, J C; Hainsworth, D W; Reid, D C; Anderson, D L; McPhee, R J [CSIRO Exploration & Minerals, Kenmore, Qld. (Australia)

    2001-10-01

    Some recent applications of sensing, guidance and telerobotic technology in the coal mining industry are presented. Of special interest is the development of semi or fully autonomous systems to provide remote guidance and communications for coal mining equipment. The use of radar and inertial based sensors are considered in an attempt to solve the horizontal and lateral guidance problems associated with mining equipment automation. Also described is a novel teleoperated robot vehicle with unique communications capabilities, called the Numbat, which is used in underground mine safety and reconnaissance missions.

  18. Mine Water Treatment in Hongai Coal Mines

    Science.gov (United States)

    Dang, Phuong Thao; Dang, Vu Chi

    2018-03-01

    Acid mine drainage (AMD) is recognized as one of the most serious environmental problem associated with mining industry. Acid water, also known as acid mine drainage forms when iron sulfide minerals found in the rock of coal seams are exposed to oxidizing conditions in coal mining. Until 2009, mine drainage in Hongai coal mines was not treated, leading to harmful effects on humans, animals and aquatic ecosystem. This report has examined acid mine drainage problem and techniques for acid mine drainage treatment in Hongai coal mines. In addition, selection and criteria for the design of the treatment systems have been presented.

  19. Mine Water Treatment in Hongai Coal Mines

    Directory of Open Access Journals (Sweden)

    Dang Phuong Thao

    2018-01-01

    Full Text Available Acid mine drainage (AMD is recognized as one of the most serious environmental problem associated with mining industry. Acid water, also known as acid mine drainage forms when iron sulfide minerals found in the rock of coal seams are exposed to oxidizing conditions in coal mining. Until 2009, mine drainage in Hongai coal mines was not treated, leading to harmful effects on humans, animals and aquatic ecosystem. This report has examined acid mine drainage problem and techniques for acid mine drainage treatment in Hongai coal mines. In addition, selection and criteria for the design of the treatment systems have been presented.

  20. Adaptation policy in hard coal mining. Die Anpassungspolitik im Steinkohlenbergbau

    Energy Technology Data Exchange (ETDEWEB)

    Brink, H J; Haas, H; Jochum, E; Muellendorff, R; Rolshoven, H

    1981-01-01

    The book points out the necessity of balancing the output of hard coal mines. Detailed analyses of marketing conditions serve as a decision aid for business policy. Production and sales trends in German hard coal mining, instruments of adaptation to quantitative changes in sales, and empirical investigations of adaptation instruments in the underground part of the Goettelborn mine are reviewed.

  1. 30 CFR 49.30 - Requirements for small coal mines.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Requirements for small coal mines. 49.30 Section 49.30 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.30 Requirements for small coal...

  2. 30 CFR 49.40 - Requirements for large coal mines.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Requirements for large coal mines. 49.40 Section 49.40 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING MINE RESCUE TEAMS Mine Rescue Teams for Underground Coal Mines § 49.40 Requirements for large coal...

  3. Evaluation of occupational exposure in a underground coal mine by environmental measures of 222Rn and in vivo measurements of 210Pb in bones

    International Nuclear Information System (INIS)

    Dantas, A.L.A.; Veiga, L.H.S.; Dantas, B.M.; Melo, V.P.

    2005-01-01

    A radiological survey performed in an underground coal mining in the State of Parana, southern Brazil, has indicated the occurrence of high levels of concentration of radon and its decay products. The levels of 222 Rn concentration measured in the basement of this mine, in the period from 1999 to 2003 ranged from 2000 to 7000 Bq m -3 . It is estimated, for these workers, an average annual exposure of 2.1 WLM ranging from 0.2 to 7.2 WLM. A retrospective mortality study conducted with 2856 miners of this mining indicated a risk of lung cancer mortality greater than the one expected for the male population of the State. In this study the cumulative exposure to radon cannot be estimated since there was no radon measures in other periods. In this way, the cumulative exposure can be evaluated by through 210 Pb activities monitored in the skeleton. The measures of 210 Pb in skeleton ranged from 83 to 164 Bq, indicating that these workers were significantly exposed to 222 Rn. These results show that cumulative exposure to radon has been higher than estimated based on recent measures of the activity concentration of radon in the workplace and is compatible with the risk determined in the epidemiological study

  4. Systems analysis on the humanization of industrial life in the coal mining industry. Pt. 2. Results. Systemanalyse zur Humanisierung des Arbeitslebens im Steinkohlenbergbau. T. 2. Ergebnisse

    Energy Technology Data Exchange (ETDEWEB)

    1980-01-01

    Volume No. 8 of the series of papers quantifies the system of aims, i.e. it defines synthetic data of laws and regulations of mining of DIN standards, and VDI guidelines, of generally accepted rules of engineering as well as of certified findings of industrial science as minimum requirements. This definition is followed by the examination of the type of medium-term development to be expected in the bituminous coal mining industry of the Ruhrkohle AG up to the year 1985. Then the general aims 1 and 2 given in volume No. 7 are described in detail. These descriptions constitute an excellent summary of the present state of knowledge concerning the improvement of working conditions in the bituminous coal mining industry. Finally, a study on the transferability of research findings is given. One statement is of special importance, i.e., that transferability is not characterized by technological feasibility alone which depends to a high degree on marginal, organizational conditions within the company, e.g., on the information system, on its hierarchical structure, on the company's policy, and on departamental policy. In this study, only the technological transferability is examined. To enable us to assess it, appropriate statements are made in a brief description of the research project carried out since 1974, which was sponsored within the action programme ''Humanization of Industrial Life''.

  5. Research on and Design of a Self-Propelled Nozzle for the Tree-Type Drilling Technique in Underground Coal Mines

    Directory of Open Access Journals (Sweden)

    Yiyu Lu

    2015-12-01

    Full Text Available Due to the increasing depths of coal mines and the low permeability of some coal seams, conventional methods of gas drainage in underground mines are facing many problems. To improve gas extraction, a new technique using water jets to drill tree-type boreholes in coal seams is proposed. A self-propelled water-jet drilling nozzle was designed to drill these boreholes. The configuration of the self-propelled nozzle was optimized by conducting drilling experiments and self-propelling force measurements. Experimental results show that the optimal self-propelled nozzle has a forward orifice axial angle at 25°, a radial angle at 90°, a center distance of 1.5 mm, and backward pointing orifices with an axial angle of 25°. The self-propelling force generated by the jets of the nozzle with 30 MPa pump pressure can reach 29.8 N, enough to pull the hose and the nozzle forward without any external forces. The nozzle can drill at speeds up to 41.5 m/h with pump pressures at 30 MPa. The radial angles of the forward orifices improve the rock breaking performance of the nozzle and, with the correct angle, the rock breaking area of the orifices overlap to produce a connecting hole. The diameter of boreholes drilled by this nozzle can reach 35.2 mm. The nozzle design can be used as the basis for designing other self-propelled nozzles. The drilling experiments demonstrate the feasibility of using the tree-type drilling technique in underground mines.

  6. Mine Water Treatment in Hongai Coal Mines

    OpenAIRE

    Dang Phuong Thao; Dang Vu Chi

    2018-01-01

    Acid mine drainage (AMD) is recognized as one of the most serious environmental problem associated with mining industry. Acid water, also known as acid mine drainage forms when iron sulfide minerals found in the rock of coal seams are exposed to oxidizing conditions in coal mining. Until 2009, mine drainage in Hongai coal mines was not treated, leading to harmful effects on humans, animals and aquatic ecosystem. This report has examined acid mine drainage problem and techniques for acid mine ...

  7. Radio Frequency Propagation Model and Fading of Wireless Signal at 2.4 GHz in Underground Coal Mine

    OpenAIRE

    Patri, Ashutosh; Nimaje, Devidas S.

    2015-01-01

    Deployment of wireless sensor networks and wireless communication systems have become indispensable for better real-time data acquisition from ground monitoring devices, gas sensors, and equipment used in underground mines as well as in locating the miners, since conventional methods like use of wireline communication are rendered ineffective in the event of mine hazards such as roof-falls, fire hazard etc. Before implementation of any wireless system, the variable path loss indices for diffe...

  8. Radio frequency propagation model and fading of wireless signal at 2.4 GHz in an underground coal mine

    OpenAIRE

    Patri, A.; Nimaje, D. S.

    2015-01-01

    Wireless sensor networks and wireless communication systems have become indispensable in underground mines. Wireless sensor networks are being used for better real-time data acquisition from ground monitoring devices, gas sensors, and mining equipment, whereas wireless communication systems are needed for locating and communicating with workers. Conventional methods like wireline communication have proved to be ineffective in the event of mine hazards such as roof falls, fires etc. Before imp...

  9. Coal mine safety achievements in the USA and the contribution of NIOSH research

    Energy Technology Data Exchange (ETDEWEB)

    Esterhuizen, G.S.; Gurtunca, R.G. [NIOSH, Washington, DC (United States)

    2006-12-15

    Over the past century coal miner safety and health have seen tremendous improvements: the fatality and injury rates continue to decrease while productivity continues to increase. Many of the hazards that plagued miners in the past, such as coal bumps, methane and coal dust explosions, ground fall accidents and health issues have been significantly reduced. The contribution of NIOSH research includes products for prevention and survival of mine fires, methane control measures, design procedure for underground coal mines, methods for excavation surface controls, methods and procedures for blasting, laser usage in underground mines and prevention of electrocution from overhead power lines that have reduced accidents and injuries in underground coal mines. Health research has produced products such as the personal dust monitor, noise abating technologies and ergonomic solutions for equipment operators. Research priorities at NIOSH are set by considering surveillance statistics, stakeholder inputs and loss control principles. Future research in coal mining is directed towards respiratory diseases, noise-induced hearing loss, repetitive musculoskeletal injuries, traumatic injuries, falls of ground and mine disasters. The recent spate of accidents in coal mines resulted in the Miner Act of 2006, which includes a specific role for NIOSH in future mine safety research and development. The mine safety achievements in the USA reflect the commitment of industry, labour, government and research organizations to improving the safety of the mine worker.

  10. Automated Coal-Mine Shuttle Car

    Science.gov (United States)

    Collins, E. R., Jr.

    1984-01-01

    Cable-guided car increases efficiency in underground coal mines. Unmanned vehicle contains storage batteries in side panels for driving traction motors located in wheels. Batteries recharged during inactive periods or slid out as unit and replaced by fresh battery bank. Onboard generator charges batteries as car operates.

  11. Coal Mine Permit Boundaries

    Data.gov (United States)

    Earth Data Analysis Center, University of New Mexico — ESRI ArcView shapefile depicting New Mexico coal mines permitted under the Surface Mining Control and Reclamation Act of 1977 (SMCRA), by either the NM Mining these...

  12. CHANGE OF PARADIGM IN UNDERGROUND HARD COAL MINING THROUGH EXTRACTION AND CAPITALIZATION OF METHANE FOR ENERGY PRODUCTION

    Directory of Open Access Journals (Sweden)

    Valeriu PLESEA

    2014-05-01

    Full Text Available Besides oil and gas, coal is the most important fossil fuel for energy production. Of the energy mixture of our country, the internal production gas share is 80% of the required annual consumption, of about 14 billion cubic meters, the rest of 20% being insured by importing, by the Russian company Gazprom. The share of coal in the National Power System (NPS is of 24% and is one of the most profitable energy production sources, taking into account the continuous increase of gas price and its dependence on external suppliers. Taking into account the infestation of the atmosphere and global warming as effect of important release of greenhouse gas and carbon dioxide as a result of coal burning for energy production in thermal power plants, there is required to identify new solutions for keeping the environment clean. Such a solution is presented in the study and analysis shown in the paper and is the extraction and capitalization of methane from the coal deposits and the underground spaces remaining free after mine closures. Underground methane extraction is considered even more opportune because, during coal exploitation, large quantities of such combustible gas are released and exhausted into the atmosphere by the degasification and ventilation stations from the surface, representing and important pollution factor for the environment, as greenhouse gas with high global warming potential (high GWP of about 21 times higher than carbon dioxide.

  13. Using coal mine saline water to produce chlorine

    Energy Technology Data Exchange (ETDEWEB)

    Gnot, W; Turek, M; Walburg, Z

    1979-01-01

    Utilizing hard coal mine waters with salt concentration reaching 140 kg/mat3 in the chemical industry would significantly reduce the cost of protecting the natural environment from salt. The Institute of Chemistry and Inorganic Technology of the Silesian Technical University in Gliwice developed an efficient technology of producing chorine from underground black coal mine waters. A scheme of the technology is explained: double stage brine purification with magnesium hydroxide as by-product. During the first stage magnesium is precipitated using sodium hydroxide; after increasing salt content in the brine calcium and a low percentage of magnesium are removed by lye-sodium method. During the second stage sedimentation rate increases to 1.4 mm/s, and volume of sludge is only 1%. Magnesium hydroxide is removed using a method patented in Poland (after adding a flocculant magnesium hydroxide is left untouched). Only at a later stage does sedimentation occur. The proposed technology of utilizing mine water will be tested in an experimental plant which will be built at the Ziemowit black coal mine. (7 refs.) (In Polish)

  14. Literature review of labour turnover and absenteeism costs in the coal mining industry

    Energy Technology Data Exchange (ETDEWEB)

    Woolf, A.

    1977-01-01

    This paper includes labor turnover formulae, turnover costs, and turnover rates for the mining industry. Few meaningful studies or reports on absenteeism costs and labour turnover in mining were retrieved.

  15. Implementation of Paste Backfill Mining Technology in Chinese Coal Mines

    Science.gov (United States)

    Chang, Qingliang; Zhou, Huaqiang; Bai, Jianbiao

    2014-01-01

    Implementation of clean mining technology at coal mines is crucial to protect the environment and maintain balance among energy resources, consumption, and ecology. After reviewing present coal clean mining technology, we introduce the technology principles and technological process of paste backfill mining in coal mines and discuss the components and features of backfill materials, the constitution of the backfill system, and the backfill process. Specific implementation of this technology and its application are analyzed for paste backfill mining in Daizhuang Coal Mine; a practical implementation shows that paste backfill mining can improve the safety and excavation rate of coal mining, which can effectively resolve surface subsidence problems caused by underground mining activities, by utilizing solid waste such as coal gangues as a resource. Therefore, paste backfill mining is an effective clean coal mining technology, which has widespread application. PMID:25258737

  16. Industrial injuries in coal mines. Lesiones profesionales en la mineria del carbon

    Energy Technology Data Exchange (ETDEWEB)

    Alfageme Diaz, S

    1989-04-01

    13 tables demonstrate the differences between injuries and are divided into five categories: total injury, accidents at work, industrial diseases, accidents in the work place and accidents on the way to or from work. In these, distinction is made between the consequences at work of the injury (whether it requires absence) and the severity of the injury (slight, serious, very serious, fatal). 13 tabs.

  17. Effects of the economic recession on the European coal mining industry

    Energy Technology Data Exchange (ETDEWEB)

    Jamme, H P; Dach, G

    1976-03-01

    The sharp decline of trade cycles in the European Community, especially in the iron and steel industry; the very mild climate; and the more energy-conscious behavior of the consumer since the oil crisis caused in 1975 a further decrease in the comsumption of primary energy. (tr-auth)

  18. Hazard mitigation in coal mines

    Science.gov (United States)

    Rashmi, R. V.; Devalal, Shilpa; Jacob, Anjali; Vidhyapathi, C. M.

    2017-11-01

    Today’s world witnesses increased number of mine accidents caused due to explosion and fire. When the methane gas concentration goes high, it causes fire leading to explosion. In this paper, an IoT based system is proposed to ensure safety to the mine workers in underground collieries. The proposed system consists of DHT-11 sensor to monitor the temperature and humidity of coal mines. When the gas sensor detects high methane gas level, blower is activated so that the atmospheric air can be pumped in from outside to dilute the gas concentration. The smoke sensor is also used to detect the fire. In case of any abnormality in any of these parameters the buzzer sounds. All these parameters are uploaded to the cloud directly so that the people at the control station can be well informed of the underground mines.

  19. Coal mining in the power industry of the Federal Republic of Germany in 2000; Der Kohlenbergbau in der Energiewirtschaft der Bundesrepublik Deutschland im Jahre 2000

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    After an introductory text divided into the sections energy and coal market, coal mining and brown coal mining, extensive tables containing the most important characteristic figures of German coal mining are shown. [German] Nach einem einfuehrenden Text, der in die Abschnitte Energie- und Kohlenmarkt, Steinkohlenbergbau und Braunkohlenbergbau gegliedert ist, wird ein umfangreiches Tabellenmaterial vorgelegt, das die wichtigsten Kennzahlen des deutschen Kohlenbergbaus enthaelt.

  20. Coal mining in the power industry of the Federal Republic of Germany in 2010; Der Kohlenbergbau in der Energiewirtschaft der Bundesrepublik Deutschland im Jahre 2010

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-11-15

    The contribution under consideration reports on the coal mining in the Federal Republic of Germany in the year 2010. Statistical data are presented for the power market and coal market, brown coal mining as well as the hard coal mining. These data consider the energy consumption in Germany, power production, iron and steel production, utilization, re-cultivation and employees.

  1. Coal mining in the power industry of the Federal Republic of Germany in 1998; Der Kohlenbergbau in der Energiewirtschaft der Bundesrepublik Deutschland im Jahre 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    After an introductory text divided into the sections energy and coal market, coal mining and brown coal mining, extensive tables containing the most important characteristic figures of German coal mining are shown. (orig.) [German] Nach einem einfuehrenden Text, der in die Abschnitte Energie- und Kohlenmarkt, Steinkohlenbergbau und Braunkohlenbergbau gegliedert ist, wird ein umfangreiches Tabellenmaterial vorgelegt, das die wichtigsten Kennzahlen des deutschen Kohlenbergbaus enthaelt. (orig.)

  2. Coal mining in the power industry of the Federal Republic of Germany in 2013; Der Kohlenbergbau in der Energiewirtschaft der Bundesrepublik Deutschland im Jahre 2013

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2014-11-15

    The contribution under consideration reports on the coal mining in the Federal Republic of Germany in the year 2013. Statistical data are presented for the power market and coal market, hard coal mining as well as the brown coal mining. These data consider the energy consumption in Germany, power production, iron and steel production, utilization, re-cultivation and employees.

  3. Coal mining in the power industry of the Federal Republic of Germany in 2014; Der Kohlenbergbau in der Energiewirtschaft der Bundesrepublik Deutschland im Jahre 2014

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2015-11-15

    The contribution under consideration reports on the coal mining in the Federal Republic of Germany in the year 2014. Statistical data are presented for the power market and coal market, hard coal mining as well as the brown coal mining. These data consider the energy consumption in Germany, power production, iron and steel production, utilization, re-cultivation and employees.

  4. Coal mining in the power industry of the Federal Republic of Germany in 2016; Der Kohlenbergbau in der Energiewirtschaft der Bundesrepublik Deutschland im Jahre 2016

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2017-11-15

    The contribution under consideration reports on the coal mining in the Federal Republic of Germany in the year 2016. Statistical data are presented for the power market and coal market, hard coal mining as well as the brown coal mining. These data consider the energy consumption in Germany, power production, iron and steel production, utilization, re-cultivation and employees.

  5. Coal mining in the power industry of the Federal Republic of Germany in 2015; Der Kohlenbergbau in der Energiewirtschaft der Bundesrepublik Deutschland im Jahre 2015

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2016-11-15

    The contribution under consideration reports on the coal mining in the Federal Republic of Germany in the year 2015. Statistical data are presented for the power market and coal market, hard coal mining as well as the brown coal mining. These data consider the energy consumption in Germany, power production, iron and steel production, utilization, re-cultivation and employees.

  6. Coal-Mining Tailings as a Pozzolanic Material in Cements Industry

    Directory of Open Access Journals (Sweden)

    Santiago Yagüe

    2018-01-01

    Full Text Available The generation of enormous volumes of mine-tailing waste is standard practice in the mining industry. Large quantities of these tailings are also sources of kaolinite-rich materials that accumulate in slag heaps, causing significant environmental degradation and visual impacts on the landscape. The consequences of coal refuse dumped in slagheaps calls for the study of eco-innovative solutions and the assessment of waste types. Moreover, the environmental benefits of reusing large amounts of contaminated waste are also evident. Hence, the objective of this investigation is to expand current knowledge of new siliceous-aluminium minerals and their pozzolanic activity. Four raw tailing samples are characterized to determine their chemical (by ICP/MS analysis, morphological (by SEM/EDX analysis, and mineralogical (by XRD analysis compositions prior to their thermal activation that transforms the inert wastes at various temperatures into materials with cementitious properties. The results of XRD analysis following activation confirmed that the kaolinite content is fully transformed into metakaolinite. The coal refuse samples presented sufficiently reliable levels of pozzolanic activity for use as additives in industrial cements.

  7. Industry and improvement: state and class formations in Nova Scotia`s coal-mining countryside, 1790-1864

    Energy Technology Data Exchange (ETDEWEB)

    Samson, D.J.

    1997-12-31

    The role of state and class formation in Nova Scotia before Confederation is discussed. The farming and coal mining districts of northern Nova Scotia are described as opposing segments that together were central to the development of liberal capitalist government forms in the province. A range of economic circumstances is considered: squatters, estates, mixed farming, coal mining, trading, quarrying, and fraternal societies. The role of enterprises such as the General Mining Association, a British venture, in colonization and in constraint of local initiative and accumulation is considered. Rural liberals created a positive place in self-government, while colonial liberals constructed a liberalism that was centred around the state and economic progress. The poor and those without property were allotted marginal public roles.

  8. Current trends in China's coal mining industry; Aktuelle Entwicklungen im Steinkohlebergbau Chinas

    Energy Technology Data Exchange (ETDEWEB)

    Goerlich, B.J. [Deutsche Montan Technologie GmbH, Essen (Germany)

    2004-07-01

    It's not only its role as a coal producer which makes China to the subject of talks everywhere. China has a high economic growth despite of the global economical crisis and SARS. China shows highest scientific and technical performance, e.g. with the space flight of the first Chinese astronaut. The Transrapid is running in Shanghai, in 2003 Volkswagen has sold more cars in China than in Germany and, statistically, 2,5 Chinese share one cell phone, i.e. presently there are 500 million cell phones in China, tendency increasing. Observing the developments in Beijing or even better in Shanghai, Shenzen, Guoangou (Kanton) gives you a feeling for dynamics and economic growth which we have been missing in Germany for a long time. This national economy has been growing rapidly thus increasing also the hunger for energy. To feed this hunger is one of the main tasks of the Chinese central government; this is the only way to maintain the economic growth in the future. The economic growth is needed urgently if the changes in economy are to be implemented by the WTO and globalisation of the markets. China needs an economic growth rate of 8% in order to create new jobs needed to make for the ones breaking away in the old, government-controlled enterprises due to the new orientation in its industry. As mentioned before: energy and especially hard coal are key and engine of this development. [German] China ist nicht nur als Kohleproduzent derzeit in aller Munde. Es verfuegt ueber ein hohes Wirtschaftswachstum, trotz globaler Wirtschaftskrise und SARS. China zeigt wissenschaftlich/technische Hoechstleistung, beispielsweise mit dem Flug des 1. chinesischen Astronauten ins All. Der Transrapid faehrt in Shanghai, VW verkaufte 2003 mehr Autos in China als in Deutschland und 2,5 Chinesen teilen sich statistisch ein Mobiltelefon - es gibt also derzeit ca. 500 Mio. Mobiltelefone allein in China, Tendenz weiter steigend. Beobachtet man die Entwicklung Pekings oder noch besser die von

  9. What differences does age make? Coal mining injuries

    Energy Technology Data Exchange (ETDEWEB)

    Mallett, L.; Schwerha, D.J. [National Institute for Occupational Safety and Health, Pittsburgh, PA (United States). Research Laboratory

    2007-02-15

    The US Bureau of Labor Statistics says that in 2002 the coal mine workforce in the USA had a higher medium age than the workforce in any other sector of mining. Many older miners are part of the generation group known as Baby Boomers. The article gives figures for injuries received in underground coal mining, surface coal mining and coal preparation plant workers, analysed by age groups (Nexters, {lt}22; Generation Xers, 22-41; Baby Boomers, 42-59; Veterans, 60 and above), and also by job title. In all generation groups, more injuries were recorded in miners with less than two years experience. 4 refs., 3 tabs., 6 charts.

  10. Situation of coal mining in the Federal Republic of Germany. Year 2014

    International Nuclear Information System (INIS)

    2015-01-01

    The paper reports on the coal mining in the Federal Republic of Germany in the year 2014. Statistical data are presented for coal market, brown coal mining as well as the hard coal mining. These data consider the supply and demand of coal in Germany, and employees of the German coal industry.

  11. Coal mining situation in the Federal Republic of Germany. First half-year 1994

    International Nuclear Information System (INIS)

    1994-01-01

    The report provides up-to-date information on the German coal mining industry for the reporting time period. Data on coal mining as well as on brown coal mining cover: Production, stocks, productivity, employes, sales, imports and exports of coal and coal products. (orig.) [de

  12. Coal mining situation in the Federal Republic of Germany. Year 2016

    International Nuclear Information System (INIS)

    2017-01-01

    The paper reports on the coal mining in the Federal Republic of Germany in the year 2016. Statistical data are presented for coal market, brown coal mining as well as the hard coal mining. These data consider the supply and demand of coal in Germany, and employees of the German coal industry.

  13. Coal mining situation in the Federal Republic of Germany. Year 2015

    International Nuclear Information System (INIS)

    2016-01-01

    The paper reports on the coal mining in the Federal Republic of Germany in the year 2015. Statistical data are presented for coal market, brown coal mining as well as the hard coal mining. These data consider the supply and demand of coal in Germany, and employees of the German coal industry.

  14. Coal mine subsidence and structures

    International Nuclear Information System (INIS)

    Gray, R.E.

    1988-01-01

    Underground coal mining has occurred beneath 32 x 10 9 m 2 (8 million acres) of land in the United States and will eventually extend beneath 162 x 10 9 m 2 (40 million acres). Most of this mining has taken place and will take place in the eastern half of the United States. In areas of abandoned mines where total extraction was not achieved, roof collapse, crushing of coal pillars, or punching of coal pillars into softer mine floor or roof rock is now resulting in sinkhole or trough subsidence tens or even hundreds of years after mining. Difference in geology, in mining, and building construction practice between Europe and the United States preclude direct transfer of European subsidence engineering experience. Building damage cannot be related simply to tensile and compressive strains at the ground surface. Recognition of the subsidence damage role played by ground-structure interaction and by structural details is needed

  15. Coal Mines Security System

    OpenAIRE

    Ankita Guhe; Shruti Deshmukh; Bhagyashree Borekar; Apoorva Kailaswar; Milind E.Rane

    2012-01-01

    Geological circumstances of mine seem to be extremely complicated and there are many hidden troubles. Coal is wrongly lifted by the musclemen from coal stocks, coal washeries, coal transfer and loading points and also in the transport routes by malfunctioning the weighing of trucks. CIL —Coal India Ltd is under the control of mafia and a large number of irregularities can be contributed to coal mafia. An Intelligent Coal Mine Security System using data acquisition method utilizes sensor, auto...

  16. Characteristics of coal mine ventilation air flows.

    Science.gov (United States)

    Su, Shi; Chen, Hongwei; Teakle, Philip; Xue, Sheng

    2008-01-01

    Coal mine methane (CMM) is not only a greenhouse gas but also a wasted energy resource if not utilised. Underground coal mining is by far the most important source of fugitive methane emissions, and approximately 70% of all coal mining related methane is emitted to the atmosphere through mine ventilation air. Therefore, research and development on mine methane mitigation and utilisation now focuses on methane emitted from underground coal mines, in particular ventilation air methane (VAM) capture and utilisation. To date, most work has focused on the oxidation of very low concentration methane. These processes may be classified based on their combustion kinetic mechanisms into thermal oxidation and catalytic oxidation. VAM mitigation/utilisation technologies are generally divided into two basic categories: ancillary uses and principal uses. However, it is possible that the characteristics of ventilation air flows, for example the variations in methane concentration and the presence of certain compounds, which have not been reported so far, could make some potential VAM mitigation and utilisation technologies unfeasible if they cannot cope with the characteristics of mine site ventilation air flows. Therefore, it is important to understand the characteristics of mine ventilation air flows. Moreover, dust, hydrogen sulphide, sulphur dioxide, and other possible compounds emitted through mine ventilation air into the atmosphere are also pollutants. Therefore, this paper presents mine-site experimental results on the characteristics of mine ventilation air flows, including methane concentration and its variations, dust loadings, particle size, mineral matter of the dust, and other compounds in the ventilation air flows. The paper also discusses possible correlations between ventilation air characteristics and underground mining activities.

  17. Protective and control relays as coal-mine power-supply ACS subsystem

    Science.gov (United States)

    Kostin, V. N.; Minakova, T. E.

    2017-10-01

    The paper presents instantaneous selective short-circuit protection for the cabling of the underground part of a coal mine and central control algorithms as a Coal-Mine Power-Supply ACS Subsystem. In order to improve the reliability of electricity supply and reduce the mining equipment down-time, a dual channel relay protection and central control system is proposed as a subsystem of the coal-mine power-supply automated control system (PS ACS).

  18. Ventilation air methane destruction - the new challenge to the underground coal mining industry

    International Nuclear Information System (INIS)

    Clarke, Michael; Seddon, Duncan

    2012-01-01

    With the advent of 'Carbon Taxes' the carbon footprint of coal has become an economic as well as an environmental issue and the emission of methane in mine out- bye air as ventilation air methane (VAM) is a pending liability. As well as being economic and environmental concerns, VAM and VAM management have safety, social licence and operational factors that must also be addressed. The need to mitigate (oxidise) methane to produce carbon dioxide and water vapour (VAM destruction) and thus lower the Greenhouse footprint is coming to be seen as a necessary mining activity. However, there are several key issues to be addressed with present technology using high temperature (1000°C) thermal oxidisers. Emerging technology may involve a catalytic approach. This technology aims to lower the oxidation temperature and produce a more efficient combustion process. Several systems (based on both precious metals and transition metals) have been shown to operate below 400°C. An ultimate solution would be oxidation at ambient temperature, which is clearly demonstrated by the enzyme methane mono-oxygenase (MMO) which oxidises methane to methanol. However, the rate of oxidation at ambient temperature is too low and the structure of the bio-reactors required would be very large. The challenge is to marry the natural oxidation with modern catalytic approaches and achieve high rates of methane oxidation, in compact equipment, well below the methane auto-ignition temperature.

  19. Effects of radiation on coal mine environment -a critical review

    International Nuclear Information System (INIS)

    Singh, A.K.; Varma, N.K.; Sahay, N.; Ahmad, I.

    2001-01-01

    Due to mass-scale industrialization, world's environment is being polluted every day endangering the existence of living beings on the earth. This has attracted the attention of environmental engineers, medical practitioners, planners and researchers throughout the world. Attempts are being made to make air, water and atmosphere clean and to prevent likely hazards arising out of various industrial activities. In addition, the radiation from natural sources is all around us and has been here since time immemorial. Coal miners have small occupational radiation which arise from naturally occurring radioactive substance(s) underground. The predominant source of natural radiation present in coal mines is the radon gas. This paper describes the origin of radon and its radiological hazards. An attempt has been made to review the status of the problem likely to be caused by the different radioactive elements present in Indian coal, coal ash and allied coal-based industries. (author)

  20. Study on regional stratagem for coal mine disasters control and prevention in China

    Energy Technology Data Exchange (ETDEWEB)

    Shen, B.; Lei, Y. [China Coal Research Institute, Beijing (China)

    2009-09-15

    A regional strategy study was aimed at coal mine disaster control and prevention, which deepens and enriches the macro-strategy of coal mine disaster control and prevention, and provides an important support for the rapid and healthy development of China's regional coal industry. The country was divided into 4 regions: Northeast, North, South and Xinqing. In view of the regional status of coal mine disasters, the regulation and development trend of regional coal mine disasters was analysed, the outstanding problems and key factors were identified, and general thoughts on regional coal mine disaster control and prevention are put forward. 4 refs., 4 figs., 1 tab.

  1. A Novel Method for Borehole Blockage Removal and Experimental Study on a Hydraulic Self-Propelled Nozzle in Underground Coal Mines

    Directory of Open Access Journals (Sweden)

    Zhaolong Ge

    2016-08-01

    Full Text Available When coal bed methane (CBM drainage boreholes cross fractured, soft, or water-swelling strata, they collapse and block frequently. Borehole blockages result in a rapid decrease in CBM extraction ability, which leads to a reduction in CBM output and threatens coal mine safety production. To solve these problems, a novel method that uses a self-propelled water-jet nozzle to dredge blocked boreholes in coal seams has been proposed on the basis of the existing technology. Based on a theoretical analysis of the reason for borehole caving and the theory of blockage removal, we optimized the nozzle inlet pressure and selected an appropriate high-pressure resin pipe. A field experiment on the blockage removal of blocked CBM drainage boreholes using the proposed method was run in the Fengchun coal mine, Qijiang, Chongqing, southwest China. In this field trial, the time spent to unblock a borehole varied between 18.52 and 34.98 min, which is much shorter than using a drilling rig. After blockage removal, the average pure volume of the methane drainage of a single borehole was increased from 0.03 L/min to ~1.91–7.30 L/min, and the methane drainage concentration of a single borehole increased from 5% to ~44%–85%. The extraction effect increased significantly.

  2. 三层网络监控的新型煤矿井下电力安全监控系统研究%Three layer of network monitoring of new coal mine underground power safety monitoring system research

    Institute of Scientific and Technical Information of China (English)

    伍龙; 吴永祥; 周孟然

    2011-01-01

    利用嵌入式监控分站作为中继站,智能电力装置面向现场设备进行实时数据采集,结合地面微机管理系统,形成了三层网络监控的新型煤矿井下电力安全监控系统。介绍了系统硬件设计,并完成了系统软件设计和测试,结果表明:监控系统运行正常、动作可靠、灵敏度高、显示正确无误、各项指标均达到了设计要求,实现了三级网络整定保护定值和远程监控,提高了煤矿井下电力安全监控系统的实时数据处理能力。%Use embedded monitoring RACES as Repeaters,intelligent power device for on-site equipment real-time data acquisition,micro-processor management on the ground,formed three layer of network monitoring of new coal mine underground power safety monitoring system.This paper introduces the hardware design,and completed the system software design and test,the result shows that the monitoring system operating normally,reliable operation,high sensitivity,display correct,all indexes meet the design requirements,improve the power safety monitoring system coal mine underground real-time data processing ability.

  3. Integrated method of RS and GPR for monitoring the changes in the soil moisture and groundwater environment due to underground coal mining

    Science.gov (United States)

    Bian, Zhengfu; Lei, Shaogang; Inyang, Hilary I.; Chang, Luqun; Zhang, Richen; Zhou, Chengjun; He, Xiao

    2009-03-01

    Mining affects the environment in different ways depending on the physical context in which the mining occurs. In mining areas with an arid environment, mining affects plants’ growth by changing the amount of available water. This paper discusses the effects of mining on two important determinants of plant growth—soil moisture and groundwater table (GWT)—which were investigated using an integrated approach involving a field sampling investigation with remote sensing (RS) and ground-penetrating radar (GPR). To calculate and map the distribution of soil moisture for a target area, we initially analyzed four models for regression analysis between soil moisture and apparent thermal inertia and finally selected a linear model for modeling the soil moisture at a depth 10 cm; the relative error of the modeled soil moisture was about 6.3% and correlation coefficient 0.7794. A comparison of mined and unmined areas based on the results of limited field sampling tests or RS monitoring of Landsat 5-thermatic mapping (TM) data indicated that soil moisture did not undergo remarkable changes following mining. This result indicates that mining does not have an effect on soil moisture in the Shendong coal mining area. The coverage of vegetation in 2005 was compared with that in 1995 by means of the normalized difference vegetation index (NDVI) deduced from TM data, and the results showed that the coverage of vegetation in Shendong coal mining area has improved greatly since 1995 because of policy input RMB¥0.4 per ton coal production by Shendong Coal Mining Company. The factor most affected by coal mining was GWT, which dropped from a depth of 35.41 m before mining to a depth of 43.38 m after mining at the Bulianta Coal Mine based on water well measurements. Ground-penetrating radar at frequencies of 25 and 50 MHz revealed that the deepest GWT was at about 43.4 m. There was a weak water linkage between the unsaturated zone and groundwater, and the decline of water table

  4. Behaviour of radium isotopes released with brines and sediments from coal mines in Poland

    International Nuclear Information System (INIS)

    Wysocka, M.; Chalupnik, S.; Mielnikow, A.; Lebecka, J.; Skubacz, K.

    1998-01-01

    Saline waters occurring in underground coal mines in Poland often contain natural radioactive isotopes, mainly 226 Ra from uranium series and 228 Ra from thorium series. Approximately 40% of total amount of radium remains underground in a form of radioactive deposits, but 225 MBq of 226 Ra and 380 MBq of 228 Ra are released daily to the rivers with mine effluents. Technical measures as spontaneous precipitation of radium in gobs, decreasing of amounts of water inflowing into underground working etc. have been undertaken in several coal mines and in the result total amount of radium released to the surface waters diminished by about 60% during last 5-6 years. Mine waters can cause a severe impact on the natural environment. The enhancement of radium concentration in river waters, bottom sediments and vegetation is observed. Sometimes radium concentration in rivers exceeds 0.7 kBq/m 3 , which is due to Polish law a permissible level for liquid radioactive waste. It was necessary to undertake investigations for development the methods of the purification of mine waters from radium. The radium balance in effluents has been calculated and a map of radioactive contamination of river waters have been prepared. Solid wastes with enhanced natural radioactivity have been produced in huge amounts in energy and coal industries in Poland. There are two main sources of these waste products. As a result of combustion of coal in power plants low radioactive waste materials are produced, with 226 Ra concentration seldom exceeding few hundreds of Bq/kg. Different situation is be observed in coal mines, where as a result of precipitation of radium from radium-bearing waters radioactive deposits are formed. Sometimes natural radioactivity of such materials is very high, in case of scaling from coal mines radium concentration may reach 4x10 5 Bq/kg - similar activity as for 3% uranium ore. Therefore maintenance of solid waste with technologically enhanced natural radioactivity (TENR

  5. Coal Mine Methane in Russia

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-07-01

    This paper discusses coal mine methane emissions (CMM) in the Russian Federation and the potential for their productive utilisation. It highlights specific opportunities for cost-effective reductions of CMM from oil and natural gas facilities, coal mines and landfills, with the aim of improving knowledge about effective policy approaches.

  6. 77 FR 26046 - Proposed Extension of Existing Information Collection; Ground Control for Surface Coal Mines and...

    Science.gov (United States)

    2012-05-02

    ... Extension of Existing Information Collection; Ground Control for Surface Coal Mines and Surface Work Areas of Underground Coal Mines AGENCY: Mine Safety and Health Administration, Labor. ACTION: Request for... inspections and investigations in coal or other mines shall be made each year for the purposes of, among other...

  7. Steam coal mines of tomorrow

    Energy Technology Data Exchange (ETDEWEB)

    McCloskey, G

    1986-07-01

    A comprehensive review of new steam coal mines being planned or developed worldwide. It shows that at least 20 major mines with a combined annual output of 110 million tonnes per annum, could add their coal to world markets in the next 10 years. The review highlights: substantial activity in Australia with at least four major mines at advanced planning stages; a strengthening of the South American export industry with 4 major mines operating in 10 years compared with just one today; no major export mines being developed in the traditional US mining areas; and the emergence of Indonesia as a major steam coal producer/exporter. The review also shows a reduction in cost/output ratios, and also the proximity of the new mines to existing infrastructure (e.g. export terminals, rail links).

  8. A study of trends in occupational risks associated with coal mining

    Energy Technology Data Exchange (ETDEWEB)

    Amoundru, C.

    1980-10-01

    The occupational risks associated with underground coal mining can be categorized as either industrial accidents or occupational diseases. Since 1957, the number of fatal accidents per million tons of coal produced has dropped by a factor of four. The number of industrial accidents in general decreased by 30% during 1967-75. The main occupational diseases affecting miners are arthrosis, deafness, and pneumoconiosis. To make an objective comparison with the health hazards from other sources of energy, the probable risks facing workers in a modern mine should be compared with those currently confronting workers in other industries.

  9. Application of MIKE SHE to study the impact of coal mining on river runoff in Gujiao mining area, Shanxi, China.

    Directory of Open Access Journals (Sweden)

    Jianhua Ping

    Full Text Available Coal mining is one of the core industries that contribute to the economic development of a country but deteriorate the environment. Being the primary source of energy, coal has become essential to meet the energy demand of a country. It is excavated by both opencast and underground mining methods and affects the environment, especially hydrological cycle, by discharging huge amounts of mine water. Natural hydrological processes have been well known to be vulnerable to human activities, especially large scale mining activities, which inevitably generate surface cracks and subsidence. It is therefore valuable to assess the impact of mining on river runoff for the sustainable development of regional economy. In this paper, the impact of coal mining on river runoff is assessed in one of the national key coal mining sites, Gujiao mining area, Shanxi Province, China. The characteristics of water cycle are described, the similarities and differences of runoff formation are analyzed in both coal mining and pre-mining periods. The integrated distributed hydrological model named MIKE SHE is employed to simulate and evaluate the influence of coal mining on river runoff. The study shows that mining one ton of raw coal leads to the reduction of river runoff by 2.87 m3 between 1981 and 2008, of which the surface runoff decreases by 0.24 m3 and the baseflow by 2.63 m3. The reduction degree of river runoff for mining one ton of raw coal shows an increasing trend over years. The current study also reveals that large scale coal mining initiates the formation of surface cracks and subsidence, which intercepts overland flow and enhances precipitation infiltration. Together with mine drainage, the natural hydrological processes and the stream flows have been altered and the river run off has been greatly reduced.

  10. Application of MIKE SHE to study the impact of coal mining on river runoff in Gujiao mining area, Shanxi, China.

    Science.gov (United States)

    Ping, Jianhua; Yan, Shiyan; Gu, Pan; Wu, Zening; Hu, Caihong

    2017-01-01

    Coal mining is one of the core industries that contribute to the economic development of a country but deteriorate the environment. Being the primary source of energy, coal has become essential to meet the energy demand of a country. It is excavated by both opencast and underground mining methods and affects the environment, especially hydrological cycle, by discharging huge amounts of mine water. Natural hydrological processes have been well known to be vulnerable to human activities, especially large scale mining activities, which inevitably generate surface cracks and subsidence. It is therefore valuable to assess the impact of mining on river runoff for the sustainable development of regional economy. In this paper, the impact of coal mining on river runoff is assessed in one of the national key coal mining sites, Gujiao mining area, Shanxi Province, China. The characteristics of water cycle are described, the similarities and differences of runoff formation are analyzed in both coal mining and pre-mining periods. The integrated distributed hydrological model named MIKE SHE is employed to simulate and evaluate the influence of coal mining on river runoff. The study shows that mining one ton of raw coal leads to the reduction of river runoff by 2.87 m3 between 1981 and 2008, of which the surface runoff decreases by 0.24 m3 and the baseflow by 2.63 m3. The reduction degree of river runoff for mining one ton of raw coal shows an increasing trend over years. The current study also reveals that large scale coal mining initiates the formation of surface cracks and subsidence, which intercepts overland flow and enhances precipitation infiltration. Together with mine drainage, the natural hydrological processes and the stream flows have been altered and the river run off has been greatly reduced.

  11. Application of ERTS-A imagery to fracture related mine safety hazards in the coal mining industry

    Science.gov (United States)

    Wier, C. E.; Wobber, F. J. (Principal Investigator)

    1973-01-01

    The author has identified the following significant results. The most important result to date is the demonstration of the special value of repetitive ERTS-1 multiband coverage for detecting previously unknown fracture lineaments despite the presence of a deep glacial overburden. The Illinois Basin is largely covered with glacial drift and few rock outcrops are present. A contribution to the geological understanding of Illinois and Indiana has been made. Analysis of ERTS-1 imagery has provided useful information to the State of Indiana concerning the surface mined lands. The contrast between healthy vegetation and bare ground as imaged by Band 7 is sharp and substantial detail can be obtained concerning the extent of disturbed lands, associated water bodies, large haul roads, and extent of mined lands revegetation. Preliminary results of analysis suggest a reasonable correlation between image-detected fractures and mine roof fall accidents for a few areas investigated. ERTS-1 applications to surface mining operations appear probable, but further investigations are required. The likelihood of applying ERTS-1 derived fracture data to improve coal mine safety in the entire Illinois Basin is suggested from studies conducted in Indiana.

  12. Model of environmental life cycle assessment for coal mining operations

    Energy Technology Data Exchange (ETDEWEB)

    Burchart-Korol, Dorota, E-mail: dburchart@gig.eu; Fugiel, Agata, E-mail: afugiel@gig.eu; Czaplicka-Kolarz, Krystyna, E-mail: kczaplicka@gig.eu; Turek, Marian, E-mail: mturek@gig.eu

    2016-08-15

    This paper presents a novel approach to environmental assessment of coal mining operations, which enables assessment of the factors that are both directly and indirectly affecting the environment and are associated with the production of raw materials and energy used in processes. The primary novelty of the paper is the development of a computational environmental life cycle assessment (LCA) model for coal mining operations and the application of the model for coal mining operations in Poland. The LCA model enables the assessment of environmental indicators for all identified unit processes in hard coal mines with the life cycle approach. The proposed model enables the assessment of greenhouse gas emissions (GHGs) based on the IPCC method and the assessment of damage categories, such as human health, ecosystems and resources based on the ReCiPe method. The model enables the assessment of GHGs for hard coal mining operations in three time frames: 20, 100 and 500 years. The model was used to evaluate the coal mines in Poland. It was demonstrated that the largest environmental impacts in damage categories were associated with the use of fossil fuels, methane emissions and the use of electricity, processing of wastes, heat, and steel supports. It was concluded that an environmental assessment of coal mining operations, apart from direct influence from processing waste, methane emissions and drainage water, should include the use of electricity, heat and steel, particularly for steel supports. Because the model allows the comparison of environmental impact assessment for various unit processes, it can be used for all hard coal mines, not only in Poland but also in the world. This development is an important step forward in the study of the impacts of fossil fuels on the environment with the potential to mitigate the impact of the coal industry on the environment. - Highlights: • A computational LCA model for assessment of coal mining operations • Identification of

  13. Model of environmental life cycle assessment for coal mining operations

    International Nuclear Information System (INIS)

    Burchart-Korol, Dorota; Fugiel, Agata; Czaplicka-Kolarz, Krystyna; Turek, Marian

    2016-01-01

    This paper presents a novel approach to environmental assessment of coal mining operations, which enables assessment of the factors that are both directly and indirectly affecting the environment and are associated with the production of raw materials and energy used in processes. The primary novelty of the paper is the development of a computational environmental life cycle assessment (LCA) model for coal mining operations and the application of the model for coal mining operations in Poland. The LCA model enables the assessment of environmental indicators for all identified unit processes in hard coal mines with the life cycle approach. The proposed model enables the assessment of greenhouse gas emissions (GHGs) based on the IPCC method and the assessment of damage categories, such as human health, ecosystems and resources based on the ReCiPe method. The model enables the assessment of GHGs for hard coal mining operations in three time frames: 20, 100 and 500 years. The model was used to evaluate the coal mines in Poland. It was demonstrated that the largest environmental impacts in damage categories were associated with the use of fossil fuels, methane emissions and the use of electricity, processing of wastes, heat, and steel supports. It was concluded that an environmental assessment of coal mining operations, apart from direct influence from processing waste, methane emissions and drainage water, should include the use of electricity, heat and steel, particularly for steel supports. Because the model allows the comparison of environmental impact assessment for various unit processes, it can be used for all hard coal mines, not only in Poland but also in the world. This development is an important step forward in the study of the impacts of fossil fuels on the environment with the potential to mitigate the impact of the coal industry on the environment. - Highlights: • A computational LCA model for assessment of coal mining operations • Identification of

  14. Feasibility study on the manufacture of rockwool insulation and low energy density gas from municipal, industrial and coal mine wastes

    Energy Technology Data Exchange (ETDEWEB)

    Barham, D; Phillips, C R

    1978-01-01

    It appears technically feasible to produce mineral wool from Nova Scotian coal mine waste supplement by municipal solid waste, with limestone balancing the composition. A co-product of the process is a low energy density gas suitable for close-coupled combustion. An appropriate feed mixture of 117 ton/d of Lingan coal waste, 25 ton/d of municipal solid waste, and 71 ton/d of limestone would produce approximately 100 ton/d of rockwool melt. The amount of product in fibre form is less than this, and is determined by the spinning efficiency. The energy content of the offgas is expected to be low, somewhere in the range of 1.5-2.6 MJ per standard M/sub 3/ (40-70 Btu per standard ft/sub 3/). Constraints operating on the system are the availability of municipal solid wastes, estimated to be not more than 25 ton/d, and the variability of the composition of this waste, which causes variability in the composition of the slag. Since the furnace will also produce a small quantity of pig iron about 5.5 ton/d, the hearth should be carbon-lined. Sulphur will be emitted both as hydrogen sulphide and as sulphur dioxide, but in the event of closecoupled use of the offgas to raise steam or provide heat, it is expected that the ultimate sulphur dioxide concentrations will not cause environmental concern. In terms of profitability, conservative cost projections (based on operating costs only) indicate excess revenue of approximately $840,000 power annum for the plant scale cited above. Against this revenue must be offset the captial changes for the plant. 15 refs., 17 figs., 6 tabs.

  15. The coal mining industry in the north of Colorado and Arizona; Steinkohlenbergbau im Norden Colorados und Arizonas

    Energy Technology Data Exchange (ETDEWEB)

    Dressel, S.; Tschauder, A. [Kali und Salz AG Werk Werra, Philippsthal (Germany)

    2000-10-12

    A study tour in autumn 1999, which was undertaken following the award of the Helmuth Burkhardt prize of Wirtschaftsvereinigung Bergbau e.V. to the authors, comprised visits to potash, molybdenum, lead, zinc, copper ore and coal mines in the mid-west of the USA. The Black Mesa Mine and Kayenta Mine of Peabody Western Coal Company in the Navajo Reserve in the north of Arizona, the Trapper Mine Inc. near Craig and the Twentymile Coal Company near Steamboat Springs, Colorado are described in this report. In addition to a brief description of the geology the coal winning is considered in greater detail. The Twentymile Coal Company was asked to explain the reasons for the successful operation of the colliery, which produces more than 5 mill. t anthracite per year by long wall working. (orig.) [German] Eine Exkursion im Herbst 1999, die durch die Verleihung des Helmuth-Burkhard-Preises der Wirtschaftsvereinigung Bergbau e.V. an Bergassessor Andreas Tschauder zustande kam, fuehrte zu Kali-, Molybdaen-,Blei-, Zink-, Kupfererz- sowie Steinkohlenbergwerken im Mittleren Westen der USA. In diesem Bericht wird auf die Steinkohlenbergwerke Black Mesa Mine und Kayenta Mine der Peabody Western Coal Company im Navajo Reservat im Norden Arizonas, der Trapper Mine Inc. bei Craig sowie der Twentymile Coal Company, nahe Steamboat Springs, Colorado, eingegangen. Neben einer kurzen Abhandlung ueber die Geologie wird die Gewinnung naeher betrachtet. Bei der Twentymile Coal Company wird die Frage gestellt, welches die Gruende fuer die erfolgreiche Arbeit des Bergwerks sind, die im Langfrontabbau pro Jahr mehr als 5 Mill. t Glanzkohle gewinnt. (orig.)

  16. Coal mine site reclamation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-02-15

    Coal mine sites can have significant effects on local environments. In addition to the physical disruption of land forms and ecosystems, mining can also leave behind a legacy of secondary detrimental effects due to leaching of acid and trace elements from discarded materials. This report looks at the remediation of both deep mine and opencast mine sites, covering reclamation methods, back-filling issues, drainage and restoration. Examples of national variations in the applicable legislation and in the definition of rehabilitation are compared. Ultimately, mine site rehabilitation should return sites to conditions where land forms, soils, hydrology, and flora and fauna are self-sustaining and compatible with surrounding land uses. Case studies are given to show what can be achieved and how some landscapes can actually be improved as a result of mining activity.

  17. Analytical study on U/G coal mine CPT and inferences

    Energy Technology Data Exchange (ETDEWEB)

    Dey, N.C.; Mukhopadhyay, S. [Bengal Engineering College, Howrath (India). Dept. of Mining and Geology

    1999-08-01

    The analytical aspects of underground CPT (coal mine cost per tonne), which varies from mine to mine due to the different weightages of various contributing factors, are described. The CPT is not only dictated by the increasing wages but also by the availability of man-hour and accountability of machine utilization. An optimal blend of labour-intensive and machine-intensive methods involving least investment and operating cost, is a challenge for the coal industry. Technology upgradation and implementation, higher skill and morale, excellence in planning and monitoring, optimization in capacity utilization, and better consumer acceptability of coal will consistently improve the financial health of the coal mining sector. Other factors which will help improve the financial health of coal mining industries are (1) cost propaganda like safety week celebration; (2) cost consciousness at all levels; (3) noticeboard comprising the cost of man-hour and machine- hour; (4) no idle time for men as well as machine; (5) care to increase the life of machines; (6) scope of target amendment in a year; (7) prior to introducing costly machines, due weightage to be given on coal grade, mine life, geo-mining conditions; and (8) award to most economic mine and punishment to others rated below the BEP (break- even point). 2 refs., 3 figs.

  18. Fiscal 1998 overseas geological structure survey report on the engineer interchange project (coal mine technology field), Indonesia; 1998 nendo kaigai chishitsu kozo nado chosa gijutsusha koryu jigyo (tanko gijutsu bun'ya), Indonesia hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project aims at improvement of coal mining technology and productivity in Indonesia by Japanese production control technology and business management technology for underground coal mining, through interchange of coal engineers between Japan and Indonesia. This project is composed of the short- term and long-term dispatch project of engineers to Indonesia, and the training project of Indonesian engineers in Japan. In fiscal 1998, the short-term dispatch was made for the training in Indonesia on underground coal mine development (development planning, pit mouth selection, main gallery design, mining system selection, transport planning, ventilation planning, under-river mining, mine water proofing, drainage). The long-term dispatch was made for contact and negotiation with concerned Indonesian organizations, support of the training project, and collection of information on the trend of Indonesian economy and energy, and the present and trend of the coal industry for conducting smooth and effective engineer interchange. (NEDO)

  19. Injury experience in coal mining, 1990

    Energy Technology Data Exchange (ETDEWEB)

    None

    1991-01-01

    This Mine Safety and Health Administration (MSHA) informational report reviews in detail the occupational injury and illness experience of coal mining in the United States for 1990. Data reported by operators of mining establishments concerning work injuries are summarized by work location, accident classification, part of body injured, nature of injury, occupation, and anthracite or bituminous coal. Related information on employment, worktime, and operating activity also is presented. Data reported by independent contractors performing certain work at mining locations are depicted separately in this report. For ease of comparison between coal mining and the metal and nonmetal mineral mining industries, summary reference tabulations are included at the end of both the operator and the contractor sections of this report.

  20. Injury experience in coal mining, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Reich, R.B.; Hugler, E.C.

    1994-05-01

    This Mine Safety and Health Administration (MSHA) informational report reviews in detail the occupational injury and illness experience of coal mining in the United States for 1992. Data reported by operators of mining establishments concerning work injuries are summarized by work location, accident classification, part of body injured, nature of injury, occupation, and anthracite or bituminous coal. Related information on employment, worktime, and operating activity also is presented. Data reported by independent contractors performing certain work at mining locations are depicted separately in this report. For ease of comparison between coal mining and the metal and nonmetal mineral mining industries, summary reference tabulations are included at the end of both the operator and the contractor sections of this report.

  1. Strata control in deep coal mines. Control de estratos en tajos subteraneos de la mineria del carbon

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez Oyanguren, P.; De la Cuadra, L.

    1985-01-01

    The six chapters cover the following subjects: mining methods used in Spanish coal mines; rock movement and pressure around a longwall face; roof bed study; underground support systems; gas dynamic phenomena; and instrumentation for underground mine monitoring.

  2. Environmental impact of coal mining on the natural environment in Poland

    International Nuclear Information System (INIS)

    Wysocka, M.; Chalupnik, S.; Michalik, B.; Skowronek, J.; Skubacz, K.

    2002-01-01

    Saline waters occurring in underground coal mines in Poland often contain natural radioactive isotopes, mainly 226 Ra from uranium series and 228 Ra from thorium series. Approximately 40% of total amount of radium remains underground in a form of radioactive deposits, but 225 MBq of 226 Ra and 400 MBq of 228 Ra are released daily to the rivers with mine effluents. Technical measures as spontaneous precipitation of radium in gobs, decreasing of amounts of water inflows into underground working etc. have been undertaken in several coal mines and as the result total amount of radium released to the surface waters diminished of about 60% during last 5-6 years. Mine waters can cause a severe impact on the natural environment, mainly due to its salinity. But also the enhancement of radium concentration in river waters, bottom sediments and vegetation is observed. Sometimes radium concentration in rivers exceeds 0.7 kBq/m 3 , which is due to Polish law a permissible level for waste waters. The extended investigations were performed in all coal mines and on this basis the radium balance in effluents has been calculated. Measurements done in the vicinity of mine water's settling ponds and in rivers gave us an opportunity to survey radium behaviour in river waters and the range of contamination. Solid waste materials with enhanced natural radioactivity have been produced in huge amounts in power and coal industries in Poland. There are two main sources of these waste products. As a result of combustion of coal in power plants low radioactive waste materials are produced, with 226 Ra concentration seldom exceeding few hundreds of Bq/kg. Different situation is observed in coal mines, where as a result of precipitation of radium from radium-bearing waters radioactive deposits are formed. Sometimes natural radioactivity of such materials is very high, in case of scaling from coal mines radium concentration may reach 400 000 Bq/kg - similar activity as for 3% uranium ore

  3. Contamination of settling ponds and rivers as a result of discharge of radium-bearing waters from Polish coal mines.

    Science.gov (United States)

    Chalupnik, S; Michalik, B; Wysocka, M; Skubacz, K; Mielnikow, A

    2001-01-01

    Saline waters from underground coal mines in Poland often contain natural radioactive isotopes, mainly 226Ra from the uranium decay series and 228Ra from the thorium series. Approximately 40% of the total amount of radium remains underground as radioactive deposits, but 225 MBq of 226Ra and 400 MBq of 228Ra are released daily into the rivers along with the other mine effluents from all Polish coal mines. Technical measures such as inducing the precipitation of radium in gobs, decreasing the amount of meteoric inflow water into underground workings, etc. have been undertaken in several coal mines, and as a result of these measures, the total amount of radium released to the surface waters has diminished by about 60% during the last 5-6 years. Mine water can have a severe impact on the natural environment, mainly due to its salinity. However, associated high levels of radium concentration in river waters, bottom sediments and vegetation have also been observed. Sometimes radium concentrations in rivers exceed 0.7 kBq/m3, which is the permitted level for waste waters under Polish law. The extensive investigations described here were carried out for all coal mines and on this basis the total radium balance in the effluents has been calculated. Measurements in the vicinity of mine settling ponds and in rivers have given us an opportunity to study radium behaviour in river waters and to assess the degree of contamination. Solid waste materials with enhanced natural radioactivity have been produced in huge amounts in the power and coal industries in Poland. As a result of the combustion of coal in power plants, low-radioactive waste materials are produced, with 226Ra concentration seldom exceeding a few hundreds of Bq/kg. A different situation is observed in coal mines, where, as a result of precipitation of radium from radium-bearing waters, highly radioactive deposits are formed. Sometimes the radioactivity of such materials is extremely high; precipitates from coal

  4. Model of environmental life cycle assessment for coal mining operations.

    Science.gov (United States)

    Burchart-Korol, Dorota; Fugiel, Agata; Czaplicka-Kolarz, Krystyna; Turek, Marian

    2016-08-15

    This paper presents a novel approach to environmental assessment of coal mining operations, which enables assessment of the factors that are both directly and indirectly affecting the environment and are associated with the production of raw materials and energy used in processes. The primary novelty of the paper is the development of a computational environmental life cycle assessment (LCA) model for coal mining operations and the application of the model for coal mining operations in Poland. The LCA model enables the assessment of environmental indicators for all identified unit processes in hard coal mines with the life cycle approach. The proposed model enables the assessment of greenhouse gas emissions (GHGs) based on the IPCC method and the assessment of damage categories, such as human health, ecosystems and resources based on the ReCiPe method. The model enables the assessment of GHGs for hard coal mining operations in three time frames: 20, 100 and 500years. The model was used to evaluate the coal mines in Poland. It was demonstrated that the largest environmental impacts in damage categories were associated with the use of fossil fuels, methane emissions and the use of electricity, processing of wastes, heat, and steel supports. It was concluded that an environmental assessment of coal mining operations, apart from direct influence from processing waste, methane emissions and drainage water, should include the use of electricity, heat and steel, particularly for steel supports. Because the model allows the comparison of environmental impact assessment for various unit processes, it can be used for all hard coal mines, not only in Poland but also in the world. This development is an important step forward in the study of the impacts of fossil fuels on the environment with the potential to mitigate the impact of the coal industry on the environment. Copyright © 2016 Elsevier B.V. All rights reserved.

  5. Participatory Communication and Sustainability Development: Case Study of Coal Mining Environment in East Kalimantan, Indonesia

    Directory of Open Access Journals (Sweden)

    Inda Fitryarini

    2018-03-01

    Full Text Available This essay tries to analyze about participatory communication, especially those currently practiced in coal mining communities in Samarinda, East Kalimantan Province, Indonesia. In addition, specific practices to facilitate participatory communication are identified and discussed. This essay is based on the author's research on environmental conflicts in coal mining areas. The conclusion of this essay is that community participatory communication in coal mining industry area is still at a pseudo participatory stage.

  6. THE CONCENTRATION OF THE CAPITAL IN THE COAL MINING INDUSTRY FROM JIU VALLEY IN THE 30s OF THE XX CENTURY

    Directory of Open Access Journals (Sweden)

    MIRCEA BARON

    2015-10-01

    Full Text Available After World War I as a result of the process of "nationalization" of the existing mining companies, of the application of the Law on the commercialization of the economic enterprises of the State of 7 June 1925, of the general trend of creating new industrial companies, in the Jiu Valley will continue operation many mining companies, called upon to exploit the rich coal deposit existing in the basement of the region. To the recovery period and then to momentum of the world economy during the third decade of the twentieth century, follows, however in a specific economic cyclicity, the period of economic crisis of the years 1929-1933. By crisis is also struck still from years 1926-1927, mining and quarrying of coal, and consequently the coal mining from the Jiu Valley, and one of the levers by which those who have led the destinies of this economic complex tried to pull the region out of crisis was the policy of rationalization, through which was aimed, primarily, a decrease in material costs through a better organization of work and through a renewal of the fixed capital based on the new technique that allowed an increase in labor productivity. Not in the least, it is accented in this period the concentration process of production and capital, either through mergers or by seizing small mining companies or undertakings, whether by purchase of land in order to form large mining complexes.

  7. Study of application of ERTS-A imagery to fracture related mine safety hazards in the coal mining industry

    Science.gov (United States)

    Wier, C. E.; Wobber, F. J. (Principal Investigator); Russell, O. R.; Amato, R. V.

    1973-01-01

    The author has identified the following significant results. The utility of ERTS-1/high altitude aircraft imagery to detect underground mine hazards is strongly suggested. A 1:250,000 scale mined lands map of the Vincennes Quadrangle, Indiana has been prepared. This map is a prototype for a national mined lands inventory and will be distributed to State and Federal offices.

  8. Simulating the Various Subsystems of a Coal Mine

    Directory of Open Access Journals (Sweden)

    V. Okolnishnikov

    2016-06-01

    Full Text Available A set of simulation models of various subsystems of a coal mine was developed with the help of a new visual interactive simulation system of technological processes. This paper contains a brief description of this simulation system and its possibilities. The main possibilities provided by the simulation system are: the quick construction of models from library elements, 3D representation, and the communication of models with actual control systems. These simulation models were developed for the simulation of various subsystems of a coal mine: underground conveyor network subsystems, pumping subsystems and coal face subsystems. These simulation models were developed with the goal to be used as a quality and reliability assurance tool for new process control systems in coal mining.

  9. Coal mine subsidence

    International Nuclear Information System (INIS)

    Darmody, R.G.; Hetzler, R.T.; Simmons, F.W.

    1992-01-01

    Longwall coal mining in southern Illinois occurs beneath some of the best agricultural land in the U.S. This region is characterized by highly productive, nearly level, and somewhat poorly drained soils. Subsidence from longwall mining causes changes in surface topography which alters surface and subsurface hydrology. These changes can adversely affect agricultural land by creating wet or ponded areas that can be deleterious to crop production. While most subsided areas show little impact from subsidence, some areas experience total crop failure. Coal companies are required by law to mitigate subsidence damage to cropland. The objective of this paper is to test the effectiveness of mitigation in restoring grain yields to their pre-mined levels. The research was conducted on sites selected to represent conventional mitigation techniques on the predominate soils in the area. Corn (Zea mays L.) and soybean [Glycine max.(L.) Merr] yields in 1988, 1989, 1990, and 1991 from mitigated areas were compared to yields from nearby undisturbed areas

  10. Injury experience in coal mining, 1991

    Energy Technology Data Exchange (ETDEWEB)

    1991-12-31

    This Mine Safety and Health Administration (MSHA) informational report reviews in detail the occupational injury and illness experience of coal mining in the United States for 1991. Data reported by operators of mining establishments concerning work injuries are summarized by work location, accident classification, part of body injured, nature of injury, occupation, and anthracite or bituminous coal. Related information on employment, worktime, and operating activity also is presented. Data reported by independent contractors performing certain work at mining locations are depicted separately in this report. For ease of comparison between coal mining and the metal and nonmetal mineral mining industries, summary reference tabulations are included at the end of both the operator and the contractor sections of this report. Data used in compiling this report were reported by operators of coal mines and preparation plants on a mandatory basis as required under the Federal Mine Safety and Health Act of 1977, Public Law 91-173,as amended by Public Law 95-164. Since January 1, 1978, operators of mines or preparation plants or both which are subject to the Act have been required under 30 CFR, Part 50, to submit reports of injuries, occupational illnesses, and related data.

  11. Crowding-out effect of coal industry investment in coal mining area: taking Shanxi province in China as a case.

    Science.gov (United States)

    Li, Li; Lei, Yalin; Xu, Qun; Wu, Sanmang; Yan, Dan; Chen, Jiabin

    2017-10-01

    The rapid development of coal industry in Shanxi province in China has important effects on its economic development. A large amount of money has been invested into the coal industry and other related industries during the recent years. However, research on the investment effect of Shanxi's coal industry was rare. In order to analyze the investment effect of coal industry, based on the crowding-out effect model, cointegration test, and the data available in Shanxi Statistical Yearbooks, this paper calculates the effect between coal industry investment and other 17 industry investment. The results show that the investment of coal industry produces crowding-out effect on food industry, building materials industry, and machinery industry. Increasing 1% of the coal industry investment can reduce 0.25% of the food industry investment, or 0.6% of building materials industry investment, or 0.52% of the machinery industry investment, which implies that Shanxi province should adjust coal industrial structure, promote the balance development of coal industry and other industries, so as to promote its economic growth.

  12. Coal Mining-Related Respiratory Diseases

    Science.gov (United States)

    ... Topics Publications and Products Programs Contact NIOSH NIOSH COAL WORKERS' HEALTH SURVEILLANCE PROGRAM Recommend on Facebook Tweet Share Compartir Coal Mining-Related Respiratory Diseases Coal mining-related respiratory ...

  13. Tube bundle system: for monitoring of coal mine atmosphere.

    Science.gov (United States)

    Zipf, R Karl; Marchewka, W; Mohamed, K; Addis, J; Karnack, F

    2013-05-01

    A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fire or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. Most longwall coal mines in Australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflow monitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

  14. Research on Occupational Safety, Health Management and Risk Control Technology in Coal Mines.

    Science.gov (United States)

    Zhou, Lu-Jie; Cao, Qing-Gui; Yu, Kai; Wang, Lin-Lin; Wang, Hai-Bin

    2018-04-26

    This paper studies the occupational safety and health management methods as well as risk control technology associated with the coal mining industry, including daily management of occupational safety and health, identification and assessment of risks, early warning and dynamic monitoring of risks, etc.; also, a B/S mode software (Geting Coal Mine, Jining, Shandong, China), i.e., Coal Mine Occupational Safety and Health Management and Risk Control System, is developed to attain the aforementioned objectives, namely promoting the coal mine occupational safety and health management based on early warning and dynamic monitoring of risks. Furthermore, the practical effectiveness and the associated pattern for applying this software package to coal mining is analyzed. The study indicates that the presently developed coal mine occupational safety and health management and risk control technology and the associated software can support the occupational safety and health management efforts in coal mines in a standardized and effective manner. It can also control the accident risks scientifically and effectively; its effective implementation can further improve the coal mine occupational safety and health management mechanism, and further enhance the risk management approaches. Besides, its implementation indicates that the occupational safety and health management and risk control technology has been established based on a benign cycle involving dynamic feedback and scientific development, which can provide a reliable assurance to the safe operation of coal mines.

  15. Use of phytoproductivity data in the choice of native plant species to restore a degraded coal mining site amended with a stabilized industrial organic sludge.

    Science.gov (United States)

    Chiochetta, Claudete G; Toumi, Hela; Böhm, Renata F S; Engel, Fernanda; Poyer-Radetski, Gabriel; Rörig, Leonardo R; Adani, Fabrizio; Radetski, Claudemir M

    2017-11-01

    Coal mining-related activities result in a degraded landscape and sites associated with large amounts of dumped waste material. The arid soil resulting from acid mine drainage affects terrestrial and aquatic ecosystems, and thus, site remediation programs must be implemented to mitigate this sequential deleterious processes. A low-cost alternative material to counterbalance the affected physico-chemical-microbiological aspects of the degraded soil is the amendment with low contaminated and stabilized industrial organic sludge. The content of nutrients P and N, together with stabilized organic matter, makes this material an excellent fertilizer and soil conditioner, fostering biota colonization and succession in the degraded site. However, choice of native plant species to restore a degraded site must be guided by some minimal criteria, such as plant survival/adaptation and plant biomass productivity. Thus, in this 3-month study under environmental conditions, phytoproductivity tests with five native plant species (Surinam cherry Eugenia uniflora L., C. myrianthum-Citharexylum myrianthum, Inga-Inga spp., Brazilian peppertree Schinus terebinthifolius, and Sour cherry Prunus cerasus) were performed to assess these criteria, and additional biochemical parameters were measured in plant tissues (i.e., protein content and peroxidase activity) exposed to different soil/sludge mixture proportions. The results show that three native plants were more adequate to restore vegetation on degraded sites: Surinam cherry, C. myrianthum, and Brazilian peppertree. Thus, this study demonstrates that phytoproductivity tests associated with biochemical endpoint measurements can help in the choice of native plant species, as well as aiding in the choice of the most appropriate soil/stabilized sludge proportion in order to optimize biomass production.

  16. Safety and welfare of Australian black coal mine employees

    Energy Technology Data Exchange (ETDEWEB)

    Azia, N.I.; Cram, K. [University of Wollongong, Wollongong, NSW (Australia). Faculty of Engineering

    2001-07-01

    The paper outlines the status of Australian coal mining industry with respect to safety and welfare of the mine employee. The impact of the longer shift hours and compressed working week are discussed in relation to workers safety and employment levels. Longer shift hours and compressed works have been shown to be a benefit to miners, both in safety and socially. The paper also examines the role of each of government organisations, the mining and manufacturing industries on the issue and goes on to describe the various environmental control measures introduced to the Australian coal mines to ensure that high safety standards are maintained. Dust monitoring and control, noise pollution control, and diesel particulate control measures have been targeted vigorously and as a result there has been a continued drop in the coal mine related diseases as well as a decline in the workers lost time injury claims. 11 refs., 7 figs., 6 tabs.

  17. Coal mining and water quality: Criciuma's case

    International Nuclear Information System (INIS)

    Fernandes, Lincoln

    1999-01-01

    The coal mining in the Santa Catarina Coal-Basin started in 1885 and since them it has been causing serious damage to the environment, specially the water resources, causing several problems like sedimentation and acidification of the rivers that supply the region, and compromising the agricultural-industry and fishery. The mining is also responsible for several professional diseases. The region was considered, in 1980, the '14th Critical Area' to the Pollution Control and Environmental Quality Conservation. Only in the beginning of the 80's, after the publication of the 917 Interministerial Resolution (July, 1982), the first official actions were taken, in order to minimize the environmental impact due to the coal mining industry. With that scenario, the region was chosen as one of the study areas of the 'National Center of Control of Mining Pollution', derived from an agreement between the Departamento Nacional de Producao Mineral - DNPM and the Japan International Cooperation Agency (JICA). The present study is part of the set of studies that have been realized in the region, with the aim of evaluating the environmental impact caused by the coal mining industry, and to suggest actions (to the miners) in order to minimize the environmental problems. This study presents a review of the occupation process of the Criciuma region, its connection to the coal industry, the progress of the mineral and environmental legislation, and the periodic monitoring of environmental parameters (physic-chemical analysis of the Mae Luzia and Sangao rivers, and the drainage from two coal mines) during the period of three years. This period began before the setting of environmental restrictions, going up to after the adoption of reclamation actions. The results allow to conclude that, during the period studied, there was no improvement in the river water characteristics, despite the adoption of reclamation actions. This behaviour may be due to the following factors: there are several

  18. Study of application of ERTS-A imagery to fracture-related mine safety hazards in the coal mining industry

    Science.gov (United States)

    Wier, C. E.; Wobber, F. J. (Principal Investigator); Russell, O. R.; Amato, R. V.; Leshendok, T. V.

    1974-01-01

    The author has identified the following significant results. The mine refuse inventory maps were prepared in response to a need by both the State and the coal industry. The lack of information on the scope of the problem handicapped all people concerned in drafting realistic legislation for a severance tax on coal production to raise funds for restoration of refuse sites. The inventory was conducted rapidly and economically, and demonstrated the benefits which can be derived through remote sensing methods.

  19. Coal mining situation in the Federal Republic of Germany. Year 2016; Zur Lage des Kohlenbergbaus in der Bundesrepublik Deutschland. Jahr 2016

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2017-03-03

    The paper reports on the coal mining in the Federal Republic of Germany in the year 2016. Statistical data are presented for coal market, brown coal mining as well as the hard coal mining. These data consider the supply and demand of coal in Germany, and employees of the German coal industry.

  20. Situation of coal mining in the Federal Republic of Germany. Year 2014; Zur Lage des Kohlenbergbaus in der Bundesrepublik Deutschland. Jahr 2014

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2015-03-10

    The paper reports on the coal mining in the Federal Republic of Germany in the year 2014. Statistical data are presented for coal market, brown coal mining as well as the hard coal mining. These data consider the supply and demand of coal in Germany, and employees of the German coal industry.

  1. Coal mining situation in the Federal Republic of Germany. Year 2015; Zur Lage des Kohlenbergbaus in der Bundesrepublik Deutschland. Jahr 2015

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2016-03-08

    The paper reports on the coal mining in the Federal Republic of Germany in the year 2015. Statistical data are presented for coal market, brown coal mining as well as the hard coal mining. These data consider the supply and demand of coal in Germany, and employees of the German coal industry.

  2. Coal mining situation in the Federal Republic of Germany. Year 2017; Zur Lage des Kohlenbergbaus in der Bundesrepublik Deutschland. Jahr 2017

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2018-03-12

    The paper reports on the coal mining in the Federal Republic of Germany in the year 2017. Statistical data are presented for coal market, brown coal mining as well as the hard coal mining. These data consider the supply and demand of coal in Germany, and employees of the German coal industry.

  3. Application Research on Testing Efficiency of Main Drainage Pump in Coal Mine Using Thermodynamic Theories

    OpenAIRE

    Shang, Deyong

    2017-01-01

    The efficiency of a drainage pump should be tested at regular intervals to master the status of the drainage pump in real time and thus achieve the goal of saving energy. The ultrasonic flowmeter method is traditionally used to measure the flow of the pump. But there are some defects in this kind of method of underground coal mine. This paper first introduces the principle of testing the main drainage pump efficiency in coal mine using thermodynamic theories, then analyzes the energy transfor...

  4. Web of Things-Based Remote Monitoring System for Coal Mine Safety Using Wireless Sensor Network

    OpenAIRE

    Bo, Cheng; Xin, Cheng; Zhongyi, Zhai; Chengwen, Zhang; Junliang, Chen

    2014-01-01

    Frequent accidents have occurred in coal mine enterprises; therefore, raising the technological level of coal mine safety monitoring systems is an urgent problem. Wireless sensor networks (WSN), as a new field of research, have broad application prospects. This paper proposes a Web of Things- (WoT-) based remote monitoring system that takes full advantage of wireless sensor networks in combination with the CAN bus communication technique that abstracts the underground sensor data and capabili...

  5. Purification of mine water of radium - The implementation of the technology in a coal mine

    International Nuclear Information System (INIS)

    Chalupnik, S.

    2002-01-01

    In underground coal mines in the Upper Silesian Coal Basin there are inflows of highly mineralised waters containing radium isotopes. These waters cause radioactive pollution of the natural environment in mining areas. Therefore cleaning of saline waters of radium is very important. Two types of radium-bearing waters were distinguished - one type containing radium and barium ions, but no sulphates (type A) and another one in which radium and sulphate ions are present but no barium (type B). A very efficient and inexpensive method of purification of saline waters, of Ba 2+ and Ra 2+ ions was developed and implemented in two coal mines. As the result of used technology, based on application of phosphogypsum as the cleaning agent, a significant decrease of radium discharge was achieved - daily of about 120 MBq of 226 Ra and 80 MBq of 228 Ra. Another type of radium waters does not contain barium ions, but contains sulphate ions SO 4 2- . There is no carrier for co-precipitation of radium so radium is transported with discharged waters to main rivers. Different method of purification from radium must be applied for such waters. Laboratory and field experiments were performed, and a cleaning method was chosen. For purification of saline waters - waste products from other industrial processes are applied. The method of purification have been applied in full technical scale in coal mine with very good results - of about 6 m 3 /min of radium-bearing waters is cleaned. Whole this process takes place in underground old workings without any contact of mining crew with radioactive deposits, which are produced during the process. As a result radium amount released to the natural environment was significantly diminished - approximately of about 90 MBq of 226 Ra per day and 150 MBq of 228 Ra. (author)

  6. Environmental aspects of hard coal mines closure in Poland

    International Nuclear Information System (INIS)

    Chaber, M.; Krogulski, K.; Gawlik, L.

    1998-01-01

    The environmental problems that arise during the closure processes of hard coal mines in Poland are undertaken in the paper. The problems of changes in water balance in rock mass are described with a stress put on underground water management. Regulation concerning ground reclamation and utilisation and removal of existing heat and power plants which after the mines closure will continue to supply surrounding consumers are stressed and the possible solutions are shown. 13 refs

  7. The Impact of Variability of Selected Geological and Mining Parameters on the Value and Risks of Projects in the Hard Coal Mining Industry

    Science.gov (United States)

    Kopacz, Michał

    2017-09-01

    The paper attempts to assess the impact of variability of selected geological (deposit) parameters on the value and risks of projects in the hard coal mining industry. The study was based on simulated discounted cash flow analysis, while the results were verified for three existing bituminous coal seams. The Monte Carlo simulation was based on nonparametric bootstrap method, while correlations between individual deposit parameters were replicated with use of an empirical copula. The calculations take into account the uncertainty towards the parameters of empirical distributions of the deposit variables. The Net Present Value (NPV) and the Internal Rate of Return (IRR) were selected as the main measures of value and risk, respectively. The impact of volatility and correlation of deposit parameters were analyzed in two aspects, by identifying the overall effect of the correlated variability of the parameters and the indywidual impact of the correlation on the NPV and IRR. For this purpose, a differential approach, allowing determining the value of the possible errors in calculation of these measures in numerical terms, has been used. Based on the study it can be concluded that the mean value of the overall effect of the variability does not exceed 11.8% of NPV and 2.4 percentage points of IRR. Neglecting the correlations results in overestimating the NPV and the IRR by up to 4.4%, and 0.4 percentage point respectively. It should be noted, however, that the differences in NPV and IRR values can vary significantly, while their interpretation depends on the likelihood of implementation. Generalizing the obtained results, based on the average values, the maximum value of the risk premium in the given calculation conditions of the "X" deposit, and the correspondingly large datasets (greater than 2500), should not be higher than 2.4 percentage points. The impact of the analyzed geological parameters on the NPV and IRR depends primarily on their co-existence, which can be

  8. A study of trends in occupational risks associated with coal mining

    International Nuclear Information System (INIS)

    Amoudru, C.

    1980-01-01

    The coal industry is well known as a major source of specific types of risk and harmful effects including, for instance, harm to the environment, pollution from various surface installations and hazards associated with the actual task of mining. We shall confine our attention to the third group and discuss only the occupational risks facing miners and ex-miners. Unlike the nuclear and oil industries, coal-mines employ very large work-forces, and the risks associated with mining therefore have a considerable impact. Mining is also a highly integrated industry: a mine's own work-force carries out all the underground engineering work (preparatory excavations, installation work, etc.) as well as maintenance. In this narrow field, a distinction should immediately be drawn between two main areas: industrial accidents; and occupational diseases, which include silicosis or, more precisely, coal-miner's pneumoconiosis

  9. Coal mining equipment

    International Nuclear Information System (INIS)

    Stein, R.R.; Martin, T.W.

    1991-01-01

    The word in longwall components is big, and these larger components have price tags to match. The logic behind the greater investment is that it will yield high production rates and good uptime statistics. This is true in most cases. More important than single-shift tonnage records, average shift production continues to climb upwards. This paper reports on the quality, and more significantly, the quantity of service supplied for long-wall equipment, which has reached levels that would have been seen as unachievable when longwall mining was first introduced in the U.S. The school of thought then was that longwall would increase productivity in part by reducing the number of production units and thus reducing the number of personnel employed underground. The expectation of fewer employees turned out to be unrealistic. That was probably one reason that some early attempts to install longwall system looked more like failures than vision of the future

  10. Study on the transformed strategy of “life field” for aged in coal mine community——A case sstudy of ccommunity rrenewal ddesign of Sihe coal mine in Jincheng, Shanxi

    Science.gov (United States)

    Xue, Minghui; Wang, Chenghao; Zhang, Shanshan

    2017-06-01

    Coal mine community is driven by the coal mine industry, and it mainly relies on coal mining enterprises to provide benefits for residents. Under the background of increasing serious global aging problem, the problems in the field of elderly people’s health, life, entertainment, communication, retirement and re-employment and other aspects become more acute and urgently to be solved. So it is necessary to make a more detailed study on how to transform the coal mine community according to the special needs of the elderly miners. This article takes renewal design of SiHe coal mine in JinCheng of ShanXi province as an example and takes the community’s “life field” as a clue, trying to put forward the transformed strategy of “life field” for aged in coal mine community and to come up with a method to update the community throughout the whole atmosphere to the personal space.

  11. Is there an association of circulatory hospitalizations independent of mining employment in coal-mining and non-coal-mining counties in west virginia?

    Science.gov (United States)

    Talbott, Evelyn O; Sharma, Ravi K; Buchanich, Jeanine; Stacy, Shaina L

    2015-04-01

    Exposures associated with coal mining activities, including diesel fuel exhaust, products used in coal processing, and heavy metals and other forms of particulate matter, may impact the health of nearby residents. We investigated the relationships between county-level circulatory hospitalization rates (CHRs) in coal and non-coal-mining communities of West Virginia, coal production, coal employment, and sociodemographic factors. Direct age-adjusted CHRs were calculated using West Virginia hospitalizations from 2005 to 2009. Spatial regressions were conducted to explore associations between CHR and total, underground, and surface coal production. After adjustment, neither total, nor surface, nor underground coal production was significantly related to rate of hospitalization for circulatory disease. Our findings underscore the significant role sociodemographic and behavioral factors play in the health and well-being of coal mining communities.

  12. Evaluation of ecological consequences of coal mine closure in Kuzbass coal region

    International Nuclear Information System (INIS)

    Schastlivcev, E.L.; Barannic, L.P.; Ovdenko, B.I.; Bykov, A.A.

    2000-01-01

    Kemerovo region (otherwise called Kuzbass) is the most industrially developed and urbanized region of Siberia, Russia. The main industrial branch of Kuzbass is coal output. Open pits and underground mines of Kuzbass produce about 40% of total amount of coal in Russia and more than 70% of coking coal. In the current process of the coal industry's restructuring, the closing of many unprofitable coal enterprises is associated with radical changes in their influence on the environment. The task to provide a probable forecast of ecological consequence of mine closure is both practically significant and complicated. In order to find some scientific approach to solve named problem the authors made in the paper the first attempts to analyze of accessible closed mines data in Kuzbass, to classify coal mines (working and closed) with respect to there negative influence on soil, water and atmosphere and to obtain some numerical estimates of possible bounds of this influence. 7 refs

  13. Feasibility of using the water from the abandoned and flooded coal mines as an energy resource for space heating

    OpenAIRE

    Athresh, AP

    2017-01-01

    This research project aims to study the feasibility of using the water from the abandoned and flooded coal mines for space heating applications using a Ground Source Heat Pump (GSHP) in open loop configuration and take a conceptual idea to a commercial deployment level. The flooded coal mines are the legacy that has been left behind after the three centuries of continuous operations by the coal mining industry. The closure of all coal mines in the UK has led to the flooding of all those aband...

  14. Testing the electrostatic characteristics of polypropylene fabric with metallic yarns, intended for use in coal mines threatened by the explosion hazard. Part 2: Tests in coal mine

    International Nuclear Information System (INIS)

    Talarek, M; Orzech, L

    2011-01-01

    The aim of this paper was to assess the electrostatic safety of polypropylene fabric with metallic yarns intended for use in coal mines. Such fabrics have not been used in the Polish mining industry yet. The tests conducted have been divided into two subgroups: laboratory tests and tests in a coal mine. This paper presents the results of tests in a coal mine, where we have focused on the resistance-to-ground in some specific situations. Bags made of fabric at the roadway face were tested, as well as the roll of fabric during transport and carried by a miner. The results obtained allow the reliable assessment of the risk of using fabrics with metallic yarns in the explosive atmosphere which often occurs in coal mines.

  15. Was it a mistake to abandon the revision clause? Assessment of entrepreneurial flexibility in the German coal mining industry on the basis of real options; War die Aufgabe der Revisionsklausel ein Fehler? Beurteilung unternehmerischer Flexibilitaet im deutschen Steinkohlebergbau auf Basis von Realoptionen

    Energy Technology Data Exchange (ETDEWEB)

    Bendiek, Ansgar

    2012-07-15

    The author analyzes the decision to abandon the revision clause, i.e. to abandon entrepreneurial flexibility on the basis of the option price theory and the use of derivatives in coal trading. The focus is on subventionless continuation of coal mining. It is found that the abandoning of the revision clause will involve a loss of value of the real option of about 819 million Euros. Politicians and the coal industry are advised to revise the subventionless continuation of coal mining by the end of 2015.

  16. 77 FR 4834 - Proposed Extension of Existing Information Collection; Refuge Alternatives for Underground Coal...

    Science.gov (United States)

    2012-01-31

    ... Extension of Existing Information Collection; Refuge Alternatives for Underground Coal Mines AGENCY: Mine... Underground Coal Mines DATES: Submit comments on or before April 2, 2012. ADDRESSES: Comments must be.... Title: Refuge Alternatives for Underground Coal Mines. OMB Number: 1219-0146. Affected Public: Business...

  17. Safety explosives in coal mining. Explosivos de seguridad en la mineria de carbon

    Energy Technology Data Exchange (ETDEWEB)

    (Union Espanola de Explosivos y Rio Blast, S.A., Madrid (Spain))

    1990-06-01

    The use of explosives in underground coal mining is essential for two reasons. The first is the highly resistant nature of the rock surrounding coal which requires explosives to remove it during development work. The second is that certain types of coal need to be blasted in order to achieve a higher output in coal winning operations. This article examines the characteristics, the types and the conditions under which safety or ion exchange explosives are used in underground coal mines where explosive atmospheres are sometimes encountered. 3 tabs. 2 pts.

  18. Determine Appropriate Post Mining Land Use in Indonesia Coal Mining Using Land Suitability Evaluation

    OpenAIRE

    Maryati, Sri; Shimada, Hideki; Hamanaka, Akihiro; Sasaoka, Takashi; Matsui, Kikuo

    2012-01-01

    Coal mining industry gives many benefits for Indonesia including contribution in total Indonesian GDP. Most of coal mines in Indonesia are open pit mining method which disturbs large area of land. One of open pit mining impact is damage land and related to soil erosion occurrences it will degrade land by top soil loses. Indonesia Government has issued mine closure regulation to encourage mining industry provide post mining land use. Determination of post mining land use should be considering ...

  19. Coal Mining vis-â-vis Agriculture in India: A Question of Sustainability

    Directory of Open Access Journals (Sweden)

    Sribas Goswami

    2015-01-01

    Full Text Available Coal mining adversely affects the eco-system as a whole. It is important to conduct suitable assessment studies to learn the potential adverse impact of mining on agriculture. In the subsequent discussions an attempt has been made to clarify the coal mining activities and its residual impact on environment and agricultural activities.The leaseholds for the underground mines are procured from the land lords who grant mining authority the right for underground coal mining. The land for houses, dwellings and the associated activities are purchased piecemeal from different sources while large portion of the surface right remained under the control of farmers and landlords. Underground mining in these areas is conducted with full responsibility of the surface protection by the operators who normally maintain pillars as the natural support to the surface features. Increasing demand for open caste mining process requires huge land. These lands sometime are acquired at the cost of cultivable land. Coal mining has direct impact over agriculture in the study region and residual impacts of mining bring far reaching consequences. The present study is explanatory in nature based on empirical facts collected from various formal sources from Coal India office. The task is to bring out the issues related to coal mining activities and their impact on vegetation and agriculture in adjoining areas in Raniganj and Jharia coalfields in India through this study.

  20. Lightweight monitoring and control system for coal mine safety using REST style.

    Science.gov (United States)

    Cheng, Bo; Cheng, Xin; Chen, Junliang

    2015-01-01

    The complex environment of a coal mine requires the underground environment, devices and miners to be constantly monitored to ensure safe coal production. However, existing coal mines do not meet these coverage requirements because blind spots occur when using a wired network. In this paper, we develop a Web-based, lightweight remote monitoring and control platform using a wireless sensor network (WSN) with the REST style to collect temperature, humidity and methane concentration data in a coal mine using sensor nodes. This platform also collects information on personnel positions inside the mine. We implement a RESTful application programming interface (API) that provides access to underground sensors and instruments through the Web such that underground coal mine physical devices can be easily interfaced to remote monitoring and control applications. We also implement three different scenarios for Web-based, lightweight remote monitoring and control of coal mine safety and measure and analyze the system performance. Finally, we present the conclusions from this study and discuss future work. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

  1. Impact of rent-seeking on productivity in Chinese coal mine safety supervision: A simulation study

    International Nuclear Information System (INIS)

    Chen, Hong; Feng, Qun; Zhu, Dandan; Han, Shuai; Long, Ruyin

    2016-01-01

    During the “golden decade” (2001–2011) of the coal industry in China, rent-seeking increased in coal mine safety supervision alongside significant improvements in coal mine safety status and increased economic benefits in the coal industry. To explore this internal relationship, we developed a Matlab simulation system and simulated the impact of rent-seeking from each level of the supervision department on coal mine productivity in different scenarios. The results showed the following. (1) Rent-seeking had no significant influence on the average level of material productivity but it had an adverse effect on the average level of mental productivity. Due to the effects of rent-seeking, productivity tended to exhibit unstable and destructive fluctuations, and rent-seeking had the dual effect of promoting and restraining productivity in a wide range with a high frequency. (2) In the supervision scenario, supervision by the high-level department was efficient, and productivity was promoted more by the national and provincial supervision department. (3) In the rent-seeking scenario, each level of the department had an intensity threshold above which coal mine accidents occurred. We also propose suggestions that focuses on the improved supervision of Chinese coal mine safety in three areas based on the “new normal” safety concept. - Highlights: •We discussed rent-seeking behavior in Chinese coal mine safety supervision. •We explored the characteristics of coal mine productivity. •We investigated the impact of rent-seeking on coal mine productivity in three scenarios. •We found rent-seeking led to great fluctuations in productivity with a dual effect. •We proposed a model strategy for Chinese coal mine safety supervision in three areas.

  2. Coal Mine Methane in Russia [Russian Version

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2010-07-01

    This paper discusses coal mine methane emissions (CMM) in the Russian Federation and the potential for their productive utilisation. It highlights specific opportunities for cost-effective reductions of CMM from oil and natural gas facilities, coal mines and landfills, with the aim of improving knowledge about effective policy approaches.

  3. Development of a Universal Safety Behavior Management System for Coal Mine Workers

    Science.gov (United States)

    LI, Jizu; LI, Yuejiao; LIU, Xiaoguang

    2015-01-01

    Background: In China, over 80% of all work-related deaths in the mining industry occur in coal mines and human factors constitute 85% of the direct causes of coal mine accidents, which indicates that significant shortcomings currently exist in the safety behavior management of Chinese coal mine workers. We aimed to verify the impact of human psychological behavior in coal mine accidents systematically through experimental study, theoretical analysis and management application. Methods: Four test instruments (Sensory and cognitive capacity test, Sixteen-Personal Factor Questionnaire, Symptom Checklist 90 Questionnaire and the supervisors’ evaluation) were employed from November 2013 to June 2014 to identify unsafe behavior factors, the self-established Questionnaire of Safety Behavior Norms (QSBN) was also used to propose the safety behavior countermeasures of coal mine employees. Results: The mental health of most coal mine workers’ is relatively poor. The sensory and cognitive capacity of those in different work posts varies greatly, as does the sense of responsibility. Workers are susceptible to external influences, and score low in site management. When the 16-PF and SCL-90 sensory and cognitive assessments were combined, the psychological index predictive power was greatest for estimating sense of efficiency and degree of satisfaction in internal evaluations, while at the same time lowest for estimating control of introversion-extroversion and stress character. Conclusion: The psychological indicators can predict part of employee safety behavior, and assist a coal mine enterprise to recruit staff, develop occupational safety norms and improve the working environment. PMID:26258088

  4. Characterization and effectiveness of remining abandoned coal mines in Pennsylvania

    International Nuclear Information System (INIS)

    Hawkins, J.W.

    1995-01-01

    Under an approved remining program, mine operators can remine abandoned coal mines without assuming legal responsibility for treatment of the previously degraded water, as long as the discharging waters are not further degraded and other regulatory requirements are satisfied. A US Bureau of Mines review of 105 remining permits in Pennsylvania indicates that remining results in substantial reclamation of abandoned mine lands, utilization of significant quantities of coal, and reduction of contaminant loads (acidity and iron) from degraded mine drainage discharges. Normality tests performed on the water quality and flow data indicate generally nonnormal distributions and extreme right-skewness tending toward lower values. The water quality of underground coal mines was observed to be more highly degraded in terms of acidity, iron, and sulfate than that of surface coal mines. The optimum baseline sampling scenario is 12 months in duration at a frequency of one sample per month. Analysis of water quality and flow rates before and after remining indicates that a majority of the mines exhibited either no change or a significant decrease in pollution rate because of remining. The discharge flow rate was the dominant controlling factor when the post-remining contaminant load was significantly better or worse than the baseline (pre-mining) load

  5. Changing organizational structures and management systems in coal industry with special consideration of the economic sphere. [Poland

    Energy Technology Data Exchange (ETDEWEB)

    Szaflik, J.

    1985-01-01

    Organizational models are analyzed for underground black coal mining in Poland from 1945 to 1984. From 1945 to 1949 organizational model of coal mining was based on selected solutions successfully tested in pre-war Poland. Coal mining was supervised by the Central Board of the Coal Industry. Coal mines were grouped in 8 and later in 10 mine associations. In 1949 the Central Board was dissolved and replaced by the Ministry of Mining and Power Generation. Role of Mine Associations was modified. Further changes were introduced in 1957. Power of Mine Associations in relation to individual coal mines increased. From 1972 to 1975 plans for a structural reform in the coal industry were developed but never realized. From 1980 to 1981 a program of structural changes in management of coal industry (in particular, underground coal mining) was developed. From 1982 to 1984 provisions of the economic reform in relation to coal mines were temporarily suspended. In 1984 a new organizational structure of the coal industry was introduced. The structure is similar to traditional structures used in previous decades (stronger position of mine associations, which since 1984 have been called Mine Unions, etc.). 9 references.

  6. The Study of Cross-layer Optimization for Wireless Rechargeable Sensor Networks Implemented in Coal Mines

    Science.gov (United States)

    Ding, Xu; Shi, Lei; Han, Jianghong; Lu, Jingting

    2016-01-01

    Wireless sensor networks deployed in coal mines could help companies provide workers working in coal mines with more qualified working conditions. With the underground information collected by sensor nodes at hand, the underground working conditions could be evaluated more precisely. However, sensor nodes may tend to malfunction due to their limited energy supply. In this paper, we study the cross-layer optimization problem for wireless rechargeable sensor networks implemented in coal mines, of which the energy could be replenished through the newly-brewed wireless energy transfer technique. The main results of this article are two-fold: firstly, we obtain the optimal relay nodes’ placement according to the minimum overall energy consumption criterion through the Lagrange dual problem and KKT conditions; secondly, the optimal strategies for recharging locomotives and wireless sensor networks are acquired by solving a cross-layer optimization problem. The cyclic nature of these strategies is also manifested through simulations in this paper. PMID:26828500

  7. 30 CFR 817.81 - Coal mine waste: General requirements.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: General requirements. 817.81... ACTIVITIES § 817.81 Coal mine waste: General requirements. (a) General. All coal mine waste disposed of in an... within a permit area, which are approved by the regulatory authority for this purpose. Coal mine waste...

  8. 30 CFR 816.81 - Coal mine waste: General requirements.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: General requirements. 816.81... ACTIVITIES § 816.81 Coal mine waste: General requirements. (a) General. All coal mine waste disposed of in an... within a permit area, which are approved by the regulatory authority for this purpose. Coal mine waste...

  9. 30 CFR 817.84 - Coal mine waste: Impounding structures.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: Impounding structures. 817.84... ACTIVITIES § 817.84 Coal mine waste: Impounding structures. New and existing impounding structures constructed of coal mine waste or intended to impound coal mine waste shall meet the requirements of § 817.81...

  10. Determining the friction factors for underground colliery bord and pillar workings

    CSIR Research Space (South Africa)

    Meyer, CF

    1998-05-01

    Full Text Available This project was mainly proposed to make available, to the coal mining industry a set of default friction values that could be used with more confidence in network simulation programs, during the project use was made of both underground...

  11. Assessment of pneumoconiosis hazards associated with mining operations in coal mines. [USSR

    Energy Technology Data Exchange (ETDEWEB)

    Sukhanov, V V; Menyailo, N I; Petul' ko, S N

    1984-07-01

    Methods are discussed for evaluating hazards of pneumoconiosis in underground coal mines. Pneumoconiosis hazards are decisively influenced by: content of respirable dusts in mine air at a working place, dust composition, temperature and time of a miner's contact with dusts. The following classification of pneumoconiosis hazards is used in the USSR: low hazards when a miner is endangered by pneumoconiosis after 20 years or more, medium hazards when pneumoconiosis may occur after 10 to 20 years, high pneumoconiosis hazards when a miner is endangered by pneumoconiosis after less than 10 years of contact with dusts. High air temperature in deep coal mines increases pneumoconiosis hazards: when temperature exceeds 26 C a temperature increase of 1 C causes a 10% increase in dust chemical activity. Safety standards which describe the maximum permissible dust level in coal mine air in the USSR, the FRG, France and Poland are compared.

  12. Gas migration from closed coal mines to the surface. Risk assessment methodology and prevention means

    International Nuclear Information System (INIS)

    Pokryszka, Z.; Tauziede, Ch.; Lagny, C.; Guise, Y.; Gobillot, R.; Planchenault, J.M.; Lagarde, R.

    2005-01-01

    French law as regards renunciation to mining concessions calls for the mining operator to first undertake analyses of the risks represented by their underground mining works. The problem of gas migration to the surface is especially significant in the context of coal mines. This is because mine gas can migrate to the earth's surface, then present significant risks: explosion, suffocation or gas poisoning risks. As part of the scheduled closure of all coal mining operations in France, INERIS has drawn up, at the request of national mining operator Charbonnages de France, a general methodology for assessing the risk linked to gas in the context of closed coal mines. This article presents the principles of this methodology. An application example based on a true case study is then described. This is completed by a presentation of the preventive and monitoring resources recommended and usually applied in order to manage the risk linked to gaseous emissions. (authors)

  13. Equipment repair in coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, S

    1982-01-01

    Most equipment in Chinese coal mines consists of machinery and equipment produced in the 1950s; the efficiency of 4-62, CTD-57 and 70B/sub 2/ ventilators is 15% lower than that of new ones; that of SSM and AYaP pumps, 10% lower than of modern ones. Equipment renovation is done in three ways: replacing obsolete equipment with new equipment of the same type; improving the performance of existing equipment by introducing efficiency and reconstruction; and replacing obsolete equipment with advanced equipment. It is indicated that the second way, for example, replacement of 4-62 ventilator blades with a maximum efficiency of 73% by 4-72 ventilator blades raises its efficiency to 90%. Replacing the 8DA-8x3 water pump, having a maximum efficiency of 63%, with the 200D 43x3 pump with a maximum efficiency of 78%, enables an electricity savings of 7000 yuan per year, which exceeds all replacement costs (600 yuan). The need to improve equipment maintenance and preventive work to increase equipment service life and to introduce new techniques and efficiency is noted.

  14. Working group report: methane emissions from coal mining

    International Nuclear Information System (INIS)

    Kruger, D.

    1993-01-01

    The process of coalification inherently generates methane and other byproducts. The amount of methane released during coal mining is a function of coal rank and depth, gas content, and mining methods, as well as other factors such as moisture. In most underground mines, methane is removed by drawing large quantities of air through the mine releasing the air into the atmosphere. In surface mines, exposed coal faces and surfaces, as well as areas of coal rubble created by blasting operations are believed to be the major sources of methane. A portion of the methane emitted from coal mining comes from post-mining activities such as coal processing, transportation, and utilisation. Some methane is also released from coal waste piles and abandoned mines. This paper highlights difficulties with previous methane emission studies namely: absence of data on which to base estimates; use of national data to develop global estimates; failure to include all possible emission sources; overreliance on statistical estimation methodologies. It recommends a 'tiered' approach for the estimation of emissions from underground mines, surface mines and post-mining activities. For each source, two or more approaches (or 'tiers') are presented, with the first tier requiring basic and readily available data and higher tiers requiring additional data. 29 refs., 3 tabs

  15. Anchor-Free Localization Method for Mobile Targets in Coal Mine Wireless Sensor Networks

    OpenAIRE

    Pei, Zhongmin; Deng, Zhidong; Xu, Shuo; Xu, Xiao

    2009-01-01

    Severe natural conditions and complex terrain make it difficult to apply precise localization in underground mines. In this paper, an anchor-free localization method for mobile targets is proposed based on non-metric multi-dimensional scaling (Multi-dimensional Scaling: MDS) and rank sequence. Firstly, a coal mine wireless sensor network is constructed in underground mines based on the ZigBee technology. Then a non-metric MDS algorithm is imported to estimate the reference nodes’ location. Fi...

  16. Problems and solutions of reliability issues for external power supply in the coal mines

    Directory of Open Access Journals (Sweden)

    И. Ю. Семыкина

    2017-08-01

    Full Text Available Restructuring of the energy sector  and liberalization of the electricity market resulted in separation of a single industry into a multitude of generating companies, federal and interregional distribution utilities, regional power providers and energy suppliers. For a number of reasons, related to the process of managing separate companies, faults in the laws and regulations, and unsatisfactory technical state of the energy equipment both on the part of distributors and consumers, reliability of energy supply faces increasing negative trends, which potentially can lead to big problems. Up to this day the energy sector does not have a developed database on the state of equipment and results of its maintenance, nor has it defined criteria to actually assess technical conditions of the equipment. The authors propose to develop and implement a mechanism aimed at technical auditing and monitoring of the engineering state of external power supply system, whose results can help in the development of more efficient and economically sound measures to improve reliability of energy supply. In recent years, a lot of attention has been paid to the issues of enhanced security of industrial power supply. However, specific characteristics of underground coal mining and enormous work load of the production process limit the applicability of developed methods and algorithms. Existing research does not address economic issues of reliable energy supply, either direct (economic damage from power interruptions, contractual security of supply, tariff regulation or indirect (charges for utility connection with a required level of reliability. There is no explicit definition for the term «autonomous energy source», nor is there a list of power receivers falling into the first and «special» categories according to their reliability. The paper contains a range of urgent problems and solutions that will increase reliability of external power supply in the coal mines.

  17. Greenhouse gas emission from Australian coal mining

    International Nuclear Information System (INIS)

    Williams, D.

    1998-01-01

    Since 1997, when the Australian Coal Association (ACA) signed a letter of Intent in respect of the governments Greenhouse Challenge Program, it has encouraged its member companies to participate. Earlier this year, the ACA commissioned an independent scoping study on greenhouse gas emissions in the black coal mining industry This was to provide background information, including identification of information gaps and R and D needs, to guide the formulation of a strategy for the mitigation of greenhouse gas emissions associated with the mining, processing and handling of black coals in Australia. A first step in the process of reducing emission levels is an appreciation of the source, quantity and type of emissions om nine sites. It is shown that greenhouse gas emissions on mine sites come from five sources: energy consumption during mining activities, the coal seam gas liberated due to the extraction process i.e. fugitive emissions, oxidation of carbonaceous wastes, land use, and embodied energy. Also listed are indications of the degree of uncertainty associated with each of the estimates

  18. Hospitalization patterns associated with Appalachian coal mining.

    Science.gov (United States)

    Hendryx, Michael; Ahern, Melissa M; Nurkiewicz, Timothy R

    2007-12-01

    The goal of this study was to test whether the volume of coal mining was related to population hospitalization risk for diseases postulated to be sensitive or insensitive to coal mining by-products. The study was a retrospective analysis of 2001 adult hospitalization data (n = 93,952) for West Virginia, Kentucky, and Pennsylvania, merged with county-level coal production figures. Hospitalization data were obtained from the Health Care Utilization Project National Inpatient Sample. Diagnoses postulated to be sensitive to coal mining by-product exposure were contrasted with diagnoses postulated to be insensitive to exposure. Data were analyzed using hierarchical nonlinear models, controlling for patient age, gender, insurance, comorbidities, hospital teaching status, county poverty, and county social capital. Controlling for covariates, the volume of coal mining was significantly related to hospitalization risk for two conditions postulated to be sensitive to exposure: hypertension and chronic obstructive pulmonary disease (COPD). The odds for a COPD hospitalization increased 1% for each 1462 tons of coal, and the odds for a hypertension hospitalization increased 1% for each 1873 tons of coal. Other conditions were not related to mining volume. Exposure to particulates or other pollutants generated by coal mining activities may be linked to increased risk of COPD and hypertension hospitalizations. Limitations in the data likely result in an underestimate of associations.

  19. Environmental problems in Russian coal industry

    International Nuclear Information System (INIS)

    Kharchenko, V.; Oumnov, V.

    1996-01-01

    The state of the Russian coal industry is complicated both economically and environmentally. Most mines are unprofitable. Several coal mines are intended to be closed. So, under existing conditions, coal mines are unable to give much attention to environmental protection problems. At the same time, coal mining is one of the most polluting industries. The main trends in this industry's negative influence upon the environment are: land spoilage and immobilization to lay out open-pit mines and mineral waste dump areas and tailing piles as well as with industrial waste water runoff; atmospheric pollution with the air coming from underground and substances blown off from dumps, hydrogeological regime intervention in coal mining areas, etc. One way to solve environmental problems in coal mining is a more rational utilization of the accompanying natural coal resources. Such measures make it possible to obtain complementary profits not only at the expense of reducing environmental destruction but producing new kinds of goods or services as well. Examples of similar solutions are solid mineral wastes utilization, underground space utilization, coal gas utilization and other issues

  20. Australian coal mine methane emissions mitigation potential using a Stirling engine-based CHP system

    International Nuclear Information System (INIS)

    Meybodi, Mehdi Aghaei; Behnia, Masud

    2013-01-01

    Methane, a major contributor to global warming, is a greenhouse gas emitted from coal mines. Abundance of coal mines and consequently a considerable amount of methane emission requires drastic measures to mitigate harmful effects of coal mining on the environment. One of the commonly adopted methods is to use emitted methane to fuel power generation systems; however, instability of fuel sources hinders the development of systems using conventional prime movers. To address this, application of Stirling engines may be considered. Here, we develop a techno-economic methodology for conducting an optimisation-based feasibility study on the application of Stirling engines as the prime movers of coal mine CHP systems from an economic and an environmental point of view. To examine the impact of environmental policies on the economics of the system, the two commonly implemented ones (i.e. a carbon tax and emissions trading scheme) are considered. The methodology was applied to a local coal mine. The results indicate that incorporating the modelled system not only leads to a substantial reduction in greenhouse gas emissions, but also to improved economics. Further, due to the heavy economic burden, the carbon tax scheme creates great incentive for coal mine industry to address the methane emissions. -- Highlights: •We study the application of Stirling engines in coal mine CHP systems. •We develop a thermo-economic approach based on the net present worth analysis. •We examine the impact of a carbon tax and ETS on the economics of the system. •The modeled system leads to a substantial reduction in greenhouse gas emissions. •Carbon tax provides a greater incentive to address the methane emissions

  1. Environmental impacts of coal mine and thermal power plant to the surroundings of Barapukuria, Dinajpur, Bangladesh.

    Science.gov (United States)

    Hossain, Md Nazir; Paul, Shitangsu Kumar; Hasan, Md Muyeed

    2015-04-01

    The study was carried out to analyse the environmental impacts of coal mine and coal-based thermal power plant to the surrounding environment of Barapukuria, Dinajpur. The analyses of coal, water, soil and fly ash were carried out using standard sample testing methods. This study found that coal mining industry and coal-based thermal power plant have brought some environmental and socio-economic challenges to the adjacent areas such as soil, water and air pollution, subsidence of agricultural land and livelihood insecurity of inhabitants. The pH values, heavy metal, organic carbon and exchangeable cations of coal water treated in the farmland soil suggest that coal mining deteriorated the surrounding water and soil quality. The SO4(2-) concentration in water samples was beyond the range of World Health Organisation standard. Some physico-chemical properties such as pH, conductivity, moisture content, bulk density, unburned carbon content, specific gravity, water holding capacity, liquid and plastic limit were investigated on coal fly ash of Barapukuria thermal power plant. Air quality data provided by the Barapukuria Coal Mining Company Limited were contradictory with the result of interview with the miners and local inhabitants. However, coal potentially contributes to the development of economy of Bangladesh but coal mining deteriorates the environment by polluting air, water and soil. In general, this study includes comprehensive baseline data for decision makers to evaluate the feasibility of coal power industry at Barapukuria and the coalmine itself.

  2. 30 CFR 716.5 - Anthracite coal mines.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Anthracite coal mines. 716.5 Section 716.5... PROGRAM REGULATIONS SPECIAL PERFORMANCE STANDARDS § 716.5 Anthracite coal mines. (a) Permittees of anthracite surface coal mining and reclamation operations in those States where the mines are regulated by...

  3. Regional technological change in US coal mines: 1951-76

    Energy Technology Data Exchange (ETDEWEB)

    Lakhani, H A

    1982-04-01

    This paper analyses technological change in coal mines in five regions - the Northern and Southern Appalachians, the Rocky Mountains, the Interior and Gulf and Northern Great Plains. Section 2 deals with changes in production profiles, over time, of the regions by dividing coal mines into underground and surface mines. It concludes that the Appalachian regions are the declining regions with lower labour productivity and that the Northern Great Plains, with its increasing labour productivity, is the expanding region. Section 3 presents a methodology of S-shaped growth curves. Section 4 reports empirical results for growth rates of adoption of the newer techniques across regions. These results reveal that the Northern Great Plains region is not absorbing the manpower and resources released by the Appalachian regions so that there are shortages in the former in the face of unemployment in the latter. There is, therefore, an opportunity for the declining Appalachian regions to inform their surplus manpower and resources about the growth centre in the north and prepare them for relocation, retraining and readjustment to the changes. (11 refs.)

  4. Underground roadway drivage with heading machines in Indian coal industry

    Energy Technology Data Exchange (ETDEWEB)

    Mukherjee, T.K.

    1983-03-01

    Heading machines have assumed a very important place in underground roadway drivage. They are not only a compromise between ''drill-and-blast'' technique and full-face machines, but are also an economic and versatile form of mechanised roadway drivage. Since the advantages gained by heading machines are considerable, the use of these machines is becoming popular in underground roadway drivage. Experience with continuous miner and heading machines in Indian coal mines is very limited compared to that of Western countries. In 1964-65, for the first time, two units of Lee Norse Miner were used at Kunostoria Colliery of Bengal Coal Company. In 1966, two units of Joy Continuous Miner were introduced at Chalkari Colliery of National Coal Development Corporation, but had to be adandoned because of heavy make of water at the installation site. A Russian PK-3 heading machine was used limitedly during the development of Banki Colliery, Madhya Pradesh. A Demag Unicorn VS-1 machine operated for the development of roadways at Jitpur and Chasnala Collieries of IISCO between 1967-70. With this machine, progress of 7 m per day was attained in level roadways and of about 2 m per day in steep raises.

  5. [Changes in the interleukin-6 and interleukin-10 concentrations in the blood plasma of miners working in deep coal mines].

    Science.gov (United States)

    Plotkin, V Ia; Rebrov, B A; Belkina, E B

    2000-03-01

    Blood plasma levels of interleukin-6 (IL-6) and interleukin-10 (IL-10) were measured in 45 miners working in a deep coal mine immediately after work shift using an immunoenzyme technique. The highest IL-6 level was recorded in those miners engaged in hard work under most adverse conditions of underground workings--it was found to exceed the control values. The same group of workers demonstrated the lowest level of IL-10 that differed from the control value. Miners aged between 41 to 50 years working in a coal mine, their underground service duration 16 to 20 years, displayed a decline in the level of IL-6. The coal mine miners with the 11- to 15-year service duration revealed an increase in the level of IL-10.

  6. The future of brown coal mining in Germany. Lectures

    International Nuclear Information System (INIS)

    Boecker, D.; Steinbach, W.C.

    1992-01-01

    Like most other sectors, the German brown coal mining industry is facing new challenges with the unification process. Major problems are also raised by the supply network, another dramatic GDR legacy - namely the need to recultivate the mining-devasted areas. Ideas to overcome such problems are shown by Dr.-Ing. Dietrich Boecker (board member of Rheinbau Ltd.) and the Leipzig government president, Mr. Walter Christian Steinbach, in the realm of an organised politics and science discussion on October 6, 1992. (HS). 6 figs [de

  7. Hydroseeding on anthracite coal-mine spoils

    Science.gov (United States)

    Miroslaw M. Czapowskyj; Ross Writer

    1970-01-01

    A study was made of the performance of selected species of legumes, grasses, and trees hydroseeded on anthracite coal-mine spoils in a slurry of lime, fertilizer, and mulch. Hydroseeding failed on coal-breaker refuse, but was partially successful on strip-mine spoils.

  8. Research on water pollution induced by coal mining

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Q.; Dong, D.; Fu, Y.; Bai, X.; Sun, Z. [China University of Mining and Technology, Xuzhou (China). Dept of Resource Exploitation Engineering

    2002-01-01

    Water environment problems induced by mining were studied. Influences of coal mining on runoff of rivers and on water sources were discussed. And the forming mechanism of acid water was analysed. The result shows that the mining activity is gradually changing the co-environment of adjacent areas, especially the water. With the water sources being continually polluted, the underground water has some poisonous or harmful ions in the process of dynamic exchange of water. The falling level of water table results in an increase of depression cone, and the seepage of rivers and the increasing range of acid water have more or less influence on water sources. All these are threatening the normal life of human beings. 11 refs., 2 figs.

  9. Residence time of contaminants released in surface coal mines -- a wind-tunnel study

    Energy Technology Data Exchange (ETDEWEB)

    Thompson, R.S. [Environmental Protection Agency, Research Triangle Park, NC (United States)

    1994-12-31

    Surface coal mining operations (blasting, shoveling, loading, trucking, etc.) are sources of airborne particles. The 1990 Clean Air Act Amendments direct the EPA to analyze the accuracy of the Industrial Source Complex model and the AP-42 emission factors, and to make revisions as may be necessary to eliminate any significant over-prediction of air concentration of fugitive particles from surface coal mines. A wind-tunnel study was performed at the US EPA`s Fluid Modeling Facility to investigate dispersion from surface coal mines in support of the dispersion modeling activities. Described here is the portion of the study directed at determining the residence time that material released near the floor of a mine will stay within the mine.

  10. Unattached fraction of radon progeny in Polish coal mines

    International Nuclear Information System (INIS)

    Skubacz, K.; Michalik, B.

    2002-01-01

    The system of the monitoring of the radiation hazard in Polish coal mines is based on the monitoring of the workplaces. This system works since 1989 in all coal mines. It gives a very good basis for further epidemiological investigation and assessment of the health detriment within the population of the mines as a result of the exposure for natural radiation. It is very important problem, due to the fact of the presence in the mines another factors, which probably have a synergetic effects on the respiratory tracts. As the routine instrument, a device called ALFA-31 sampling probe was developed in our laboratory. This device was accomplished to regular dust sampler and simultaneous measurements of dust content and potential alpha energy concentration of radon progeny are obligatory in all underground mines in Poland. But the microcyclone used a separator of the respirable fraction which causes the cut-off of unattached fraction of radon progeny, On the other hand measurements of the unattached fraction of short lived radon progeny play a very important role in the investigations of the adequate dose from this source of radiation hazard. During field experiments the use of the alpha spectroscopy system is necessary, while measurements are done not in the vacuum chambers but under normal pressure. It leads to situation, when particular peaks in alpha spectrum are very wide and interfere with other peaks of another alpha-emitting radionuclides. Such instrumentation was designed and completed, and a survey in several underground mines was performed. The analysis of the obtained results must be done very carefully; in other case it may cause a very big uncertainty of the result. In this paper a new approach to the analysis of the alpha spectra has been described. This approach can be used also in other applications of alpha spectroscopy, in which the analysis of energy of alpha peaks in spectrum is needed. The method of the analysis is based on a non-linear regression

  11. AN OPERATIONAL MANAGEMENT MODEL FOR A COAL MINING PRODUCTION UNIT

    Directory of Open Access Journals (Sweden)

    R. Visser

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: The coal mining industry faces increased pressure for higher quality coal at lower cost and increased volumes. To satisfy these requirements the industry needs technically skilled first line supervisors with operational management skills. Most first line supervisors possess the necessary technical, but not the required operational management skills. Various operational management philosophies, describing world-class operational management practices exist; however, it is not possible to implement these philosophies as-is in a mining environment due to the various differences between manufacturing and mining. The solution is to provide an operational management model, adapted from these philosophies, to first line supervisors in the coal mining industry.

    AFRIKAANSE OPSOMMING: Die steenkoolmynbedryf ervaar groeiende druk van die mark vir hoër gehalte steenkool, laer koste en verhoogde volumes. Om hierdie behoefte te bevredig benodig die myn tegniesgeskoolde eerstelyntoesighouers met bedryfsbestuursvaardighede. Ongelukkig beskik die meeste toesighouers wel oor die nodige tegniese kennis, maar nie die nodige bedryfsbestuursvaardighede nie. Daar bestaan verskeie bedryfsbestuursfilosofieë wat wêreldklas bedryfsbestuurspraktyke omskryf. Dit is egter nie moontlik om die filisofieë net so in die mynbedryf te implimenteer nie a.g.v. die verskille tussen vervaardiging en mynbou. Die oplossing is om ‘n bedryfsbestuurmodel wat op hierdie filosofieë geskoei is, aan eerstelyntoesighouers in die steenkoolbedryf te verskaf.

  12. Mapping and monitoring coal mine subsidence using LiDAR and InSAR

    Energy Technology Data Exchange (ETDEWEB)

    Froese, C.R.; Mei, S. [Alberta Geological Survey, Edmonton, AB (Canada). Energy Resources Conservation Board

    2008-07-01

    In the early 1900s, the abandonment of coal mines in Alberta was not regulated and closure documentation was poor. Although the general locations of mines are known, the locations of the specific adits and shafts are not. As such, there are many cases in southwestern Alberta where infrastructure was built on top of old coal mine workings without any detailed records of the abandoned mine or displacement monitoring. The crowns of these workings have been subject to ongoing strain that is reflected at the surface. The rate at which the strain is progressing prior to collapse is not well understood. Mitigation of collapse events is site specific and reactive. This paper demonstrated that airborne LiDAR and spaceborne InSAR technologies can provide valuable information on the distribution of abandoned underground coal mine workings. Both remote sensing techniques were used on Turtle Mountain in the Crowsnest Pass to obtain quantitative information on landslide mechanics, including the patterns and rate of ground movement and subsidence. These techniques can be used to map the location of surface collapse and delineate the location of the coal mine workings that were not previously documented. It was concluded that these technologies will likely become more readily available in the future and incorporated into geo-engineering practices for use in ground hazard detection, monitoring and management. 8 refs., 6 figs.

  13. Management present situation and countermeasures of coal mines safety in production

    Institute of Scientific and Technical Information of China (English)

    ZHANG Shu-dong; YU Chang-wu

    2008-01-01

    Analyzed of the present situation of Chinese coal mines safety in production and the reasons for coal mining accident, and realized the coal mines safety in production,which should increase the legal safeguards of coal mine safety in production, and safety input, established the comprehensive coal mine safety evaluation system, comprehensively enhance quality of coal mine workers, established and improved early warning mechanism of safety production of coal mine.

  14. Coal mining, social injustice and health: a universal conflict of power and priorities.

    Science.gov (United States)

    Morrice, Emily; Colagiuri, Ruth

    2013-01-01

    Given the current insatiable demand for coal to build and fuel the world's burgeoning cities the debate about mining-related social, environmental and health injustices remains eminently salient. Furthermore, the core issues appear universally consistent. This paper combines the theoretical base for defining these injustices with reports in the international health literature about the impact of coal mining on local communities. It explores and analyses mechanisms of coal mining related injustice, conflicting priorities and power asymmetries between political and industry interests versus inhabitants of mining communities, and asks what would be required for considerations of health to take precedence over wealth. Copyright © 2012 Elsevier Ltd. All rights reserved.

  15. Preliminary report on LLNL mine seismicity deployment at the Twentymile Coal Mine

    International Nuclear Information System (INIS)

    Walter, W.R.; Hunter, S.L.; Glenn, L.A.

    1996-01-01

    This report summarizes the preliminary results of a just completed experiment at the Twentymile Coal Mine, operated by the Cyprus Amax Coal Company near Oak Creek, CO. The purpose of the experiment was to obtain local and regional seismic data from roof caves associated with long-wall mining activities and to use this data to help determine the effectiveness with which these events can be discriminated from underground nuclear explosions under a future Comprehensive Test Ban Treaty

  16. Development a solid state sensor based on SnO{sub 2} nanoparticles for underground coal mine methane detection using zeolites as filter; Desenvolvimento de sensor de estado solido com nanoparticulas de SnO{sub 2} para metano de mina de carvao subterranea utilizando zeolitas como filtro

    Energy Technology Data Exchange (ETDEWEB)

    Abruzzi, R.C.; Dedavid, B.A.; Pires, M.J.R.; Luvizon, N.S., E-mail: rafael.abruzzi@acad.pucrs.br [Pontificia Universidade Catolica do Rio Grande do Sul (PUCRS), Porto Alegre, RS (Brazil)

    2016-07-01

    Aiming the monitoring of methane (CH{sub 4}) in underground coal mines, the tin oxide (SnO{sub 2}) was synthesis and applied to the development of a MOS sensor (metal oxide semiconductor). Zeolite have been tested as a filter of carbon dioxide (CO{sub 2}) to ensure the selectivity in the detection of CH{sub 4}. Analysis of Transmission Electron Microscopy (TEM) and X-Ray Diffraction (XRD) indicated a synthesis of nanoscaled structures. The energy band gap showed characteristic values for a potential application of SnO{sub 2} in CH{sub 4} sensors. Analysis of surface area by BET isotherms showed high values for the zeolite 13X and Y, while adsorption tests indicated that the zeolite 13X presents greater adsorption efficiency of CO{sub 2}. The sputtering technique for deposition of the electrodes, as well as the method of drop coating for deposition of SnO{sub 2}, proved effective in developing the sensor. (author)

  17. Basic study for promoting joint implementation and others. Feasibility study on the recovery and utilization of coal mine methane of an Upper Silesian Coal Field

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Having the Mining Industry Restructuring Public Corporation located in the city of Katowice, Poland as the counterpart, a feasibility study has been executed on a project to utilize coal bed gas for power generation. Selected for the study are the 'Budryk coal mine' owned by KWK 'Budryk' Coal Company and the 'Pniowek coal mine' owned by Jastrzebie Coal Company. Since the Pniowek coal mine can utilize the whole quantity of recovered methane by 2001, the Budryk coal mine was selected as the object of the project. As a result of the trial calculation on the economy when the new gas power plant is installed in the Budryk coal mine, the energy substitution effect was found to equal to a power amount at transmission terminal of 6 MWh/year. Furthermore, when proliferation effect is taken into consideration, an enormous effect can be expected if new coal mines are developed and the existing cola mines will go further deeper, because the Silesian coal mine presently has the coal resource quantity of 57 billion tons and the annual gas discharge quantity of 750 million m{sup 3}. Therefore, if the technologies to recover, manage and utilize the gas are established at the Budryk coal mine, a large effect leading to an aspiration would be expected under the current situation of the structural reorganization under which the Polish coal companies are placed. (NEDO)

  18. Basic study for promoting joint implementation and others. Feasibility study on the recovery and utilization of coal mine methane of an Upper Silesian Coal Field

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Having the Mining Industry Restructuring Public Corporation located in the city of Katowice, Poland as the counterpart, a feasibility study has been executed on a project to utilize coal bed gas for power generation. Selected for the study are the 'Budryk coal mine' owned by KWK 'Budryk' Coal Company and the 'Pniowek coal mine' owned by Jastrzebie Coal Company. Since the Pniowek coal mine can utilize the whole quantity of recovered methane by 2001, the Budryk coal mine was selected as the object of the project. As a result of the trial calculation on the economy when the new gas power plant is installed in the Budryk coal mine, the energy substitution effect was found to equal to a power amount at transmission terminal of 6 MWh/year. Furthermore, when proliferation effect is taken into consideration, an enormous effect can be expected if new coal mines are developed and the existing cola mines will go further deeper, because the Silesian coal mine presently has the coal resource quantity of 57 billion tons and the annual gas discharge quantity of 750 million m{sup 3}. Therefore, if the technologies to recover, manage and utilize the gas are established at the Budryk coal mine, a large effect leading to an aspiration would be expected under the current situation of the structural reorganization under which the Polish coal companies are placed. (NEDO)

  19. Exposure to noise in coal mining; Metodologia para el Control y Prevencion del Ruido en las Minas

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    This study is centred on the analysis and evaluation of risk noise to which the workers are exposed in coal mines in ASTURIAS. To this end, great many measurements were carried out on the amount in workers belonging to the various mining professional categories. The results of the study show that there are a great many workers exposed to level of noise which notably surpass those limits established by the Royal Decree, 1316/1989 on the protection of worker against risks from exposure to noise at work particularly those involved in picking and in the preparation, which are, in fact, the most typical post in underground coal mining. (Author)

  20. PROBLEMY I PERSPEKTIVY ISPOL'ZOVANIYA SHAKHTNOGO METANA [PROBLEMS AND PROSPECTS OF COAL MINE METHANE

    Directory of Open Access Journals (Sweden)

    Mogileva Ye.M.

    2017-09-01

    Full Text Available The use of coal mine methane ensures the implementation of the principle of integrated development of the deposit. The urgency of the problem of coal mine methane is determined by the fact that the Presidential Decree of September 30, 2013 № 752 "On the reduction of greenhouse gas emissions" is to bring to the 2020 decrease in emissions. The article substantiates the necessity of cardinal growth of the volumes of utilization of mine methane, as well as the strengthening of the role of degassing methods. The main reasons for the low level of utilization in the Russian Federation are noted. The main directions of using coal mine methane at present are considered, among which are: heat generation (fuel in boilers and other heat generators; generation of electricity (fuel for diesel engines of alternators; fuel for motor vehicles; raw materials for the chemical industry. The analysis of the main methods of utilization of methane-air mixtures is presented. Three perspective technologies for recycling methane from the ventilation streams of coal mines to the atmosphere are singled out: a thermal reactor with reversible flows "VOCSIDIZER", developed by MEGTEC Systems; a thermal reactor with reversible flows "VAMOX", developed by the company "Biothermica Technologies Inc."; a catalytic reversible reactor developed by Canadian Mineral and Energy Technologies. International practice shows that the implementation of projects for the utilization of coal mine methane, as a rule, requires the economic stimulation of such works. The article gives the main incentives and identifies the main directions for solving the problem of coal mine methane utilization.

  1. Selective bibliography of surface coal mining and reclamation literature. Volume 2. Interior Coal Province

    Energy Technology Data Exchange (ETDEWEB)

    Patricoski, M. L.; Daniels, L. K.; Sobek, A. A.

    1979-08-01

    This bibliography has been compiled for use by researchers, students, and other groups who need a reference source of published literature related to surface coal mining and reclamation in the Interior Coal Province. This bibliography contains more than 1300 references, including government reports, journal articles, symposium proceedings, industrial reports, workshop proceedings, theses, and bibliographies. A simple format was used to categorize citations.

  2. 75 FR 64411 - Lowering Miners' Exposure to Respirable Coal Mine Dust, Including Continuous Personal Dust Monitors

    Science.gov (United States)

    2010-10-19

    ... industries, such as mining, by reducing workplace deaths and improving the health of coal miners. This..., enhanced enforcement, collaborative outreach, and education and training. The initiative will reduce, and... reducing the respirable coal mine dust levels, miners continue to develop black lung. Based on recent data...

  3. Systems to limit coal dust and methane explosions in coal mines.

    CSIR Research Space (South Africa)

    Du Plessis, JJL

    1997-01-01

    Full Text Available In response to the need for enhanced precautionary measures to safeguard mine workers in collieries from the consequences of methane ignitions in a heading, the coal mining industry has expressed the desire for the development and testing of active...

  4. Technique of complex slime water treatment of coal-mining branch

    OpenAIRE

    Solodov, G. А.; Zhbyr, Е. V.; Papin, А. V.; Nevedrov, А. V.

    2007-01-01

    The possibility of complex slime water treatment at coal-mining and coal-treating plants producing marketable products: power-generating concentrate, coal-water fuel, magnetic fraction, industrial water is shown. A basic process flowsheet of slime water treatment presenting a united technological complex is suggested.

  5. Safety campaign in small coal mines. Campana de seguridad en la pequena mineria del carbon

    Energy Technology Data Exchange (ETDEWEB)

    1988-01-01

    Since March 1985 when the local authority took over responsibility for mine safety and following an initial analysis carried out by the Spanish Council for Industry and Commerce which holds administrative responsibility for monitoring mine safety, it has been noted that the risk of accidents and the accident rate itself were very high in small coal mines. 2 figs., 1 tabs.

  6. Selective coal mining of intercalated lignite deposits

    Energy Technology Data Exchange (ETDEWEB)

    Zunic, R [Kolubara-Projekt, Lazarevac (Yugoslavia)

    1991-01-01

    Describes selective coal mining in the Tamnava-Istocno Polje coal surface coal mine (Yugoslavia), designed for an annual coal production of 11.4 Mt. Until 1991, this mine exploited one thick lignite seam, without spoil intercalations, using a bucket wheel excavator-conveyor-spreader system both for coal mining and removal of overburden. In the future, several spoil intercalations of up to 1.0 m and thicker will appear with a total volume of 22 million m{sup 3}. These intercalations have to be selectively excavated in order to guarantee the calorific value of coal for the Nikola Tesla power plant. Computer calculations were carried out to determine the decrease in excavator coal production due to selective mining of spoil strata. Calculations found that the annual surface mine capacity will be lower by at most 9%, depending on thickness of spoil intercalations. The useful operation time of excavators will be reduced by 98 hours per year. The planned annual coal production will nevertheless be fulfilled. 3 refs.

  7. Optimizing wireless LAN for longwall coal mine automation

    Energy Technology Data Exchange (ETDEWEB)

    Hargrave, C.O.; Ralston, J.C.; Hainsworth, D.W. [Exploration & Mining Commonwealth Science & Industrial Research Organisation, Pullenvale, Qld. (Australia)

    2007-01-15

    A significant development in underground longwall coal mining automation has been achieved with the successful implementation of wireless LAN (WLAN) technology for communication on a longwall shearer. WIreless-FIdelity (Wi-Fi) was selected to meet the bandwidth requirements of the underground data network, and several configurations were installed on operating longwalls to evaluate their performance. Although these efforts demonstrated the feasibility of using WLAN technology in longwall operation, it was clear that new research and development was required in order to establish optimal full-face coverage. By undertaking an accurate characterization of the target environment, it has been possible to achieve great improvements in WLAN performance over a nominal Wi-Fi installation. This paper discusses the impact of Fresnel zone obstructions and multipath effects on radio frequency propagation and reports an optimal antenna and system configuration. Many of the lessons learned in the longwall case are immediately applicable to other underground mining operations, particularly wherever there is a high degree of obstruction from mining equipment.

  8. Are underground coal miners satisfied with their work boots?

    Science.gov (United States)

    Dobson, Jessica A; Riddiford-Harland, Diane L; Bell, Alison F; Steele, Julie R

    2018-01-01

    Dissatisfaction with work boot design is common in the mining industry. Many underground coal miners believe their work boots contribute to the high incidence of lower limb injuries they experience. Despite this, the most recent research to examine underground coal mining work boot satisfaction was conducted over a decade ago. This present study aimed to address this gap in the literature by assessing current mining work boot satisfaction in relation to the work-related requirements for underground coal mining. 358 underground coal miners (355 men; mean age = 39.1 ± 10.7 years) completed a 54-question survey regarding their job details, work footwear habits, foot problems, lower limb and lower back pain history, and work footwear fit and comfort. Results revealed that underground coal miners were not satisfied with their current mining work boots. This was evident in the high incidence of reported foot problems (55.3%), lower back pain (44.5%), knee pain (21.5%), ankle pain (24.9%) and foot pain (42.3%). Over half of the underground coal miners surveyed believed their work boots contributed to their lower limb pain and reported their work boots were uncomfortable. Different working roles and environments resulted in differences in the incidence of foot problems, lower limb pain and comfort scores, confirming that one boot design cannot meet all the work-related requirements of underground coal mining. Further research examining the interaction of a variety of boot designs across the different underground surfaces and the different tasks miners perform is paramount to identify key boot design features that affect the way underground coal miners perform. Enhanced work boot design could improve worker comfort and productivity by reducing the high rates of reported foot problems and pain amongst underground coal miners. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. An intelligent hybrid system for surface coal mine safety analysis

    Energy Technology Data Exchange (ETDEWEB)

    Lilic, N.; Obradovic, I.; Cvjetic, A. [University of Belgrade, Belgrade (Serbia)

    2010-06-15

    Analysis of safety in surface coal mines represents a very complex process. Published studies on mine safety analysis are usually based on research related to accidents statistics and hazard identification with risk assessment within the mining industry. Discussion in this paper is focused on the application of AI methods in the analysis of safety in mining environment. Complexity of the subject matter requires a high level of expert knowledge and great experience. The solution was found in the creation of a hybrid system PROTECTOR, whose knowledge base represents a formalization of the expert knowledge in the mine safety field. The main goal of the system is the estimation of mining environment as one of the significant components of general safety state in a mine. This global goal is subdivided into a hierarchical structure of subgoals where each subgoal can be viewed as the estimation of a set of parameters (gas, dust, climate, noise, vibration, illumination, geotechnical hazard) which determine the general mine safety state and category of hazard in mining environment. Both the hybrid nature of the system and the possibilities it offers are illustrated through a case study using field data related to an existing Serbian surface coal mine.

  10. Tasks in development of the USSR coal industry

    Energy Technology Data Exchange (ETDEWEB)

    Bratchenko, B F

    1981-08-01

    Minister of the Soviet coal industry evaluates social and economic development plan of the Soviet coal industry from 1981 to 1985. Planned coal production should increase to 770-800 Mt, exceeding coal production in 1980 by 53 to 83 Mt. Proportion of coal mined by surface methods will further increase. Investment program concentrates on: construction of the Kansk-Achinsk fuel and energy basin, construction of the South Yakut coal basin and further development of surface mines in the Ehkibastuz basin. Proportion of coal mined in the Kuzbass will increase to 45% of the total coal output. Construction of the Kansk-Achinsk basin has the highest priority among the investment projects. Investment projects (construction of new coal mines and modernization of existing mines) in major coal basins in 1981 are analyzed. Mining machines and equipment for underground and surface black and brown coal mining are evaluated. Plans for developing new mining systems are described (e.g. narrow web coal cutter with chainless haulage system for thin and medium coal seams with drive system with power ranging from 110 to 315 kW). The following types of machines are discussed: coal cutters, shearer loaders, heading machines, belt conveyors, loaders. Selected social problems associated with manpower shortages for underground mining and for coal mines operating under extreme climatic conditions are also discussed.

  11. Earth Conductivity Estimation from Through-the-Earth Measurements of 94 Coal Mines Using Different Electromagnetic Models

    OpenAIRE

    Yan, Lincan; Waynert, Joseph; Sunderman, Carl

    2014-01-01

    Through-the-Earth (TTE) communication systems require minimal infrastructure to operate. Hence, they are assumed to be more survivable and more conventional than other underground mine communications systems. This survivability is a major advantage for TTE systems. In 2006, Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which requires all underground coal mines to install wireless communications systems. The intent behind this mandate is for trapped miners to...

  12. A geographical information system-based analysis of cancer mortality and population exposure to coal mining activities in West Virginia, United States of America

    Directory of Open Access Journals (Sweden)

    Michael Hendryx

    2010-05-01

    Full Text Available Cancer incidence and mortality rates are high in West Virginia compared to the rest of the United States of America. Previous research has suggested that exposure to activities of the coal mining industry may contribute to elevated cancer mortality, although exposure measures have been limited. This study tests alternative specifications of exposure to mining activity to determine whether a measure based on location of mines, processing plants, coal slurry impoundments and underground slurry injection sites relative to population levels is superior to a previously-reported measure of exposure based on tons mined at the county level, in the prediction of age-adjusted cancer mortality rates. To this end, we utilize two geographical information system (GIS techniques – exploratory spatial data analysis and inverse distance mapping – to construct new statistical analyses. Total, respiratory and “other” age-adjusted cancer mortality rates in West Virginia were found to be more highly associated with the GIS-exposure measure than the tonnage measure, before and after statistical control for smoking rates. The superior performance of the GIS measure, based on where people in the state live relative to mining activity, suggests that activities of the industry contribute to cancer mortality. Further confirmation of observed phenomena is necessary with person-level studies, but the results add to the body of evidence that coal mining poses environmental risks to population health in West Virginia.

  13. Public views of reclaiming an abandoned coal mine: the Macoupin County project

    Energy Technology Data Exchange (ETDEWEB)

    Bernard, J. R.

    1980-07-01

    An abandoned underground coal mine waste area in Macoupin County, Illinois, has been reclaimed for demonstration and research purposes near the city of Staunton. According to federal law, end uses of reclaimed coal mines must be determined in part by local concerns. This study examined local residents' preferences for land uses and their social and economic evaluations of reclamation at the Macoupin County site. Personal interviews with 119 residents revealed preferences for recreational use of the demonstration area; however, responses were probably influenced by prior awareness of land-use intentions. Generally, very positive evaluations of the reclamation were received. Willingness to pay for reclamation appears to be linked to fulfillment of desired recreational uses on the site and socioeconomic status of the respondent. In general, the research results provide further evidence that the value of abatement of environmental damage from mining is recognized and supported in economic terms at the public level.

  14. Study of the Korean anthracite for utilization and the coal mine data management

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    This report consists of two articles. (1) Petrographic study of the Korean anthracite for utilization (5): This research was initiated for the development of filtering materials those can be used in waste water treatment sites The small scale of filtration tester was built on the waste water treatment site of Chungjoo electric Co. to use waste water processed by purifying system for the feasibility study. (2) Study of the closed coal mine data management: Underground maps about 1700 adits of 100 coal mines, and related graphic data have been collected in the database. And all those data were entered into the database in vectorial form, coordinates obtaining from the digitizing tablet. Detailed works are described in the other report, including the discussions of graphic database and data handling of graphical mine data. Comments about the GIS is also provided in the volume. (author). 25 refs., 45 figs., 50 tabs., 3 maps.

  15. 30 CFR 75.811 - High-voltage underground equipment; grounding.

    Science.gov (United States)

    2010-07-01

    ...-voltage equipment supplying power to such equipment receiving power from resistance grounded systems shall... 30 Mineral Resources 1 2010-07-01 2010-07-01 false High-voltage underground equipment; grounding... COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Underground High-Voltage...

  16. Comparison of Methane Control Methods in Polish and Vietnamese Coal Mines

    Science.gov (United States)

    Borowski, Marek; Kuczera, Zbigniew

    2018-03-01

    Methane hazard often occurs in hard coal mines and causes very serious accidents and can be the reason of methane or methane and coal dust explosions. History of coal mining shows that methane released from the rock mass to the longwall area was responsible for numerous mining disasters. The main source of methane are coal deposits because it is autochthonous gas and is closely related with carbonification and forming of coal deposits. Degree of methane saturation in coal deposits depends on numerous factors; mainly on presence or lack of insulating layers in cover deposit that allow or do not on degasification and easily methane outflow into surroundings. Hence in coal mining there are coal deposits that contain only low degree of methane saturation in places where is lack of insulating layers till high in methane coal deposits occurring in insulating claystones or in shales. Conducting mining works in coal deposits of high methane hazard without using of special measures to combat (ventilation, methane drainage) could be impossible. Control of methane hazard depends also on other co-occuring natural dangers for which used preventive actions eliminate methane hazard. Safety in mines excavating coal deposits saturated with methane depends on the correct estimation of methane hazard, drawn up forecasts, conducted observations, hazard control as well as undertaken prevention measures. Methane risk prevention includes identification and control methods of methane hazards as well as means of combating the explosive accumulation of methane in longwall workings. The main preventive actions in underground coal mines are: effective ventilation that prevents forming of methane fuses or placed methane accumulation in headings ventilated by airflow created by main fans and in headings with auxiliary ventilation, methane drainage using drain holes that are drilled from underground headings or from the surface, methanometry control of methane concentration in the air; location

  17. Comparison of Methane Control Methods in Polish and Vietnamese Coal Mines

    Directory of Open Access Journals (Sweden)

    Borowski Marek

    2018-01-01

    Full Text Available Methane hazard often occurs in hard coal mines and causes very serious accidents and can be the reason of methane or methane and coal dust explosions. History of coal mining shows that methane released from the rock mass to the longwall area was responsible for numerous mining disasters. The main source of methane are coal deposits because it is autochthonous gas and is closely related with carbonification and forming of coal deposits. Degree of methane saturation in coal deposits depends on numerous factors; mainly on presence or lack of insulating layers in cover deposit that allow or do not on degasification and easily methane outflow into surroundings. Hence in coal mining there are coal deposits that contain only low degree of methane saturation in places where is lack of insulating layers till high in methane coal deposits occurring in insulating claystones or in shales. Conducting mining works in coal deposits of high methane hazard without using of special measures to combat (ventilation, methane drainage could be impossible. Control of methane hazard depends also on other co-occuring natural dangers for which used preventive actions eliminate methane hazard. Safety in mines excavating coal deposits saturated with methane depends on the correct estimation of methane hazard, drawn up forecasts, conducted observations, hazard control as well as undertaken prevention measures. Methane risk prevention includes identification and control methods of methane hazards as well as means of combating the explosive accumulation of methane in longwall workings. The main preventive actions in underground coal mines are: effective ventilation that prevents forming of methane fuses or placed methane accumulation in headings ventilated by airflow created by main fans and in headings with auxiliary ventilation, methane drainage using drain holes that are drilled from underground headings or from the surface, methanometry control of methane concentration in

  18. Respirable quartz hazard associated with coal mine roof bolter dust

    International Nuclear Information System (INIS)

    Joy, G.J.; Beck, T.W.; Listak, J.M.

    2010-01-01

    Pneumoconiosis has been reported to be increasing among underground coal miners in the Southern Appalachian Region. The National Institute for Occupational Safety and Health conducted a study to examine the particle size distribution and quartz content of dust generated by the installation of roof bolts in mines. Forty-six bulk samples of roof bolting machine pre-cleaner cyclone dump dust and collector box dust were collected from 26 underground coal mines. Real-time and integrated airborne respirable dust concentrations were measured on 3 mining sections in 2 mines. The real-time airborne dust concentrations profiles were examined to identify any concentration changes that might be associated with pre-cleaner cyclone dust discharge events. The study showed that bolter dust is a potential inhalation hazard due to the fraction of dust less than 10 μm in size, and the quartz content of the dust. The pre-cleaner cyclone dust was significantly larger than the collector box dust, indicating that the pre-cleaner functioned properly in removing the larger dust size fraction from the airstream. However, the pre-cleaner dust still contained a substantial amount of respirable dust. It was concluded that in order to maintain the effectiveness of a roof bolter dust collector, periodic removal of dust is required. Appropriate work procedures and equipment are necessary to minimize exposure during this cleaning task. 13 refs., 3 tabs., 2 figs.

  19. Polymers for combatting sudden outbursts in coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Gadzhiev, G P; Sukhanov, V V

    1988-02-01

    Describes investigations in coal mines in the Donetsk basin (hazardous because of the high methane presence, the risk of outbursts of coal and gas, underground fires and the high dust levels) with the aim of studying the toxic emissions of formaldehyde and methanol produced when a urea formaldehyde resin binder is applied to the coal seam. The measurements taken led to the following recommendations: the amount of free formaldehyde in the binder should be limited to 0.5%; the use of concentrated (50%) solutions should be limited to 10 l per ton of coal in areas where there are geologic faults; underground workings need ventilation of at least 200 m/sup 3//min; the binder should be introduced to the borehole separately from the water and hardener; individual protection measures and wet dusting should be used during coal extraction; a period of not less than 4 months should elapse between application of the resin and commencement of coal extraction; there should be at least 80 m between the point where the binder is applied and the coal face.

  20. Burnout in Chinese coal mine safety supervision

    International Nuclear Information System (INIS)

    Chen, Hong; Chen, Feiyu; Zhu, Dandan; Qi, Hui; Long, Ruyin

    2015-01-01

    This study examines commonly-suffered job burnout as it relates to the practice of safety supervision in Chinese coal mine enterprises. Commonly-suffered job burnout is a form of job burnout caused by external factors. It is closely related to task characteristics rather than individual idiosyncrasies. To explore the causes of commonly-suffered job burnout, the special attributes (the integrated output attributes, conditional output attributes, and public goods attributes) of coal mine safety output and the inevitability of the invalidation of the bounded authority in safety supervision were analyzed in this study, which reveals the formation mechanism of commonly-suffered job burnout. Moreover, a confirmatory game model was constructed to analyze how the attributes of the safety output and bounded authority of safety supervision act on the safety output. The theoretical connotation of commonly-suffered job burnout was explained based on the job demands-resources theory. A comparative analysis of commonly-suffered job burnout and the job burnout that occurs in the traditional research object was also undertaken from the viewpoint of the job demands, which are determined by the characteristics of the work task and their corresponding coping resources. Policy suggestions were given based on interventions in commonly-suffered job burnout. -- Highlights: •We discuss commonly-suffered job burnout in Chinese coal enterprises. •We analyze the special attributes of coal mine safety output. •We explore two main causes of commonly-suffered job burnout. •We construct a game model to validate how the two causes act on safety output. •We put forward related policy suggestions

  1. Coal mine reclamation: the cooperative approach

    Energy Technology Data Exchange (ETDEWEB)

    Blazenko, E J; Kuhn, J A

    1976-07-01

    Salient problems encountered in coal mine reclamation include land use and environmental protection values, license applications and subsequent reports, and the development of sound reclamation planning programs. The facts of life to be dealt with in reclamation and reclamation planning include encounters with negative attitudes toward reclamation, basic physics, chemistry, biology and geology, and the ability or inability to respond properly. The cooperative approach to reclamation includes interfacing with mining company personnel, government agencies, public-interest groups and consultants. Some promising solutions to reclamation, especially in alpine and subalpine regions, include handling of materials and organic test plot research.

  2. 30 CFR 816.83 - Coal mine waste: Refuse piles.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: Refuse piles. 816.83 Section... ACTIVITIES § 816.83 Coal mine waste: Refuse piles. Refuse piles shall meet the requirements of § 816.81, the... drainage may not be diverted over the outslope of the refuse piles. Runoff from the areas above the refuse...

  3. 30 CFR 817.83 - Coal mine waste: Refuse piles.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: Refuse piles. 817.83 Section... ACTIVITIES § 817.83 Coal mine waste: Refuse piles. Refuse piles shall meet the requirements of § 817.81, the... drainage may not be diverted over the outslope of the refuse pile. Runoff from areas above the refuse pile...

  4. 78 FR 79010 - Criteria to Certify Coal Mine Rescue Teams

    Science.gov (United States)

    2013-12-27

    ... coal requires more heat to combust; (3) anthracite dust does not propagate an explosion; and (4) there... to Certify Coal Mine Rescue Teams AGENCY: Mine Safety and Health Administration, Labor. ACTION... updated the coal mine rescue team certification criteria. The Mine Improvement and New Emergency Response...

  5. 30 CFR 716.4 - Special bituminous coal mines.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Special bituminous coal mines. 716.4 Section... INTERIOR INITIAL PROGRAM REGULATIONS SPECIAL PERFORMANCE STANDARDS § 716.4 Special bituminous coal mines. (a) Definition. Special bituminous coal surface mines as used in this section means those bituminous...

  6. Polonium-210 accumulates in a lake receiving coal mine discharges-anthropogenic or natural?

    Science.gov (United States)

    Nelson, A W; Eitrheim, E S; Knight, A W; May, D; Wichman, M D; Forbes, T Z; Schultz, M K

    2017-02-01

    Coal is an integral part of global energy production; however, coal mining is associated with numerous environmental health impacts. It is well documented that coal-mine waste can contaminate the environment with naturally-occurring radionuclides from the uranium-238 ( 238 U) decay series. However, the behavior of the final radionuclide in the 238 U-series, i.e., polonium-210 ( 210 Po) arising from coal-mine waste-water discharge is largely unexplored. Here, results of a year-long (2014-2015) field study, in which the concentrations of 210 Po in sediments and surface water of a lake that receives coal-mine waste-water discharge in West Virginia are presented. Initial measurements identified levels of 210 Po in the lake sediments that were in excess of that which could be attributed to ambient U-series parent radionuclides; and were indicative of discharge site contamination of the lake ecosystem. However, control sediment obtained from a similar lake system in Iowa (an area with no coal mining or unconventional drilling) suggests that the levels of 210 Po in the lake are a natural phenomenon; and are likely unrelated to waste-water treatment discharges. Elevated levels of 210 Po have been reported in lake bottom sediments previously, yet very little information is available on the radioecological implications of 210 Po accumulation in lake bottom sediments. The findings of this study suggest that (Monthly Energy Review, 2016) the natural accumulation and retention of 210 Po in lake sediments may be a greater than previously considered (Chadwick et al., 2013) careful selection of control sites is important to prevent the inappropriate attribution of elevated levels of NORM in lake bottom ecosystems to industrial sources; and (Van Hook, 1979) further investigation of the source-terms and potential impacts on elevated 210 Po in lake-sediment ecosystems is warranted. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. Application Research on Testing Efficiency of Main Drainage Pump in Coal Mine Using Thermodynamic Theories

    Directory of Open Access Journals (Sweden)

    Deyong Shang

    2017-01-01

    Full Text Available The efficiency of a drainage pump should be tested at regular intervals to master the status of the drainage pump in real time and thus achieve the goal of saving energy. The ultrasonic flowmeter method is traditionally used to measure the flow of the pump. But there are some defects in this kind of method of underground coal mine. This paper first introduces the principle of testing the main drainage pump efficiency in coal mine using thermodynamic theories, then analyzes the energy transformation during the process of draining water, and finally derives the calculation formulae of the pump efficiency, which meet the on-site precision of engineering. On the basis of analyzing the theories, the protective sleeve and the base of the temperature sensor are designed to measure the water temperature at inlet and outlet of the pump. The efficiencies of pumps with two specifications are measured, respectively, by using the thermodynamic method and ultrasonic flowmeter method. By contrast, the results show that thermodynamic method can satisfy the precision of the testing requirements accuracy for high-flow and high-lift drainage pump under normal temperatures. Moreover, some measures are summed up to improve the accuracy of testing the pump efficiency, which are of guiding significance for on-site testing of the main drainage pump efficiency in coal mine.

  8. GIS-based Analysis of LS Factor under Coal Mining Subsidence Impacts in Sandy Region

    Directory of Open Access Journals (Sweden)

    W. Xiao

    2014-09-01

    Full Text Available Coal deposits in the adjacent regions of Shanxi, Shaanxi, and Inner Mongolia province (SSI account for approximately two-thirds of coal in China; therefore, the SSI region has become the frontier of coal mining and its westward movement. Numerous adverse impacts to land and environment have arisen in these sandy, arid, and ecologically fragile areas. Underground coal mining activities cause land to subside and subsequent soil erosion, with slope length and slope steepness (LS as the key influential factor. In this investigation, an SSI mining site was chosen as a case study area, and 1 the pre-mining LS factor was obtained using a digital elevation model (DEM dataset; 2 a mining subsidence prediction was implemented with revised subsidence prediction factors; and 3 the post-mining LS factor was calculated by integrating the pre-mining DEM dataset and coal mining subsidence prediction data. The results revealed that the LS factor leads to some changes in the bottom of subsidence basin and considerable alterations at the basin’s edges of basin. Moreover, the LS factor became larger in the steeper terrain under subsidence impacts. This integrated method could quantitatively analyse LS changes and spatial distribution under mining impacts, which will benefit and provide references for soil erosion evaluations in this region

  9. The main environmental and social problems in China's large coal mine construction and the countermeasures

    Energy Technology Data Exchange (ETDEWEB)

    Geng, Hai-qing [State Environmental Protection Administration, Beijing (China). Appraisal Center for Environment and Engineering

    2008-05-15

    Due to rapid industrialization and urbanization, the number of China's large proposed coal mines has increased very quickly in recent years. 144 environmental impact assessment reports were submitted to SEPA during 2001 2006, so the problem of reconciling coal exploitation with the environmental and social impacts has become urgent in China's sustainable development strategy. Based on analysis of data on coal mine exploitation, it is pointed out that there are four main problems in the management of the coal sector: the SEA (Strategic Environmental Assessment) lags behind the practical needs; the policy is not clear; migration is neglected; and an ecological compensatory mechanism is absent. Four countermeasures are recommended: accelerating the execution of SEA; compartmentalizing typical zones for environmental management; improving the organisation of resettlement in the coal district; and installing an ecological compensatory mechanism in the coal mining industry. 13 refs., 2 figs., 1 tab.

  10. A study on measures to reduce production cost of long-running collieries and coal mining mechanization

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-01

    The reducing coal market has been enforcing the coal industry to make exceptional rationalization and restructuring efforts since the end of the eighties. To the competition from crude oil and natural gas has been added the growing pressure from rising wages and rising production cost as the working get deeper. To improve the competitive position of the remaining 11 coal mines after the rationalization of the industry, studies to improve mining system have been carried out. This report consists of 3 subjects. 1) Designing of the bord and pillar mining method to extract gently inclined seams of the Dogye coal mine. 2) Mechanization of coal cutting by plough. 3) Achievement of the mechanization of coal mining compared to the previous year. (author). 27 refs.

  11. Study of environmental pollution and mineralogical characterization of sediment rivers from Brazilian coal mining acid drainage

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Luis F.O., E-mail: felipeqma@hotmail.com [Environmental Science and Nanotechnology Department, Institute of Environmental Research and Human Development – IPADH, Capivari de Baixo, Santa Catarina (Brazil); Laboratory of Environmental Researches and Nanotechnology Development, Centro Universitário La Salle, Victor Barreto, 2288 Centro 92010-000, Canoas, RS (Brazil); Fdez- Ortiz de Vallejuelo, Silvia; Martinez-Arkarazo, Irantzu; Castro, Kepa [Department of Analytical Chemistry, University of the Basque Country (EHU/UPV), P.O. Box 644, 48080 Bilbao, Basque Country (Spain); Oliveira, Marcos L.S. [Environmental Science and Nanotechnology Department, Institute of Environmental Research and Human Development – IPADH, Capivari de Baixo, Santa Catarina (Brazil); Sampaio, Carlos H.; Brum, Irineu A.S. de [Universidade Federal do Rio Grande do Sul, Escola de Engenharia, Departamento de Metalurgia, Centro de Tecnologia, Av. Bento Gonçalves, 9500, Bairro Agronomia, CEP: 91501-970, Porto Alegre, RS (Brazil); Leão, Felipe B. de; Taffarel, Silvio R. [Laboratory of Environmental Researches and Nanotechnology Development, Centro Universitário La Salle, Victor Barreto, 2288 Centro 92010-000, Canoas, RS (Brazil); Madariaga, Juan M. [Department of Analytical Chemistry, University of the Basque Country (EHU/UPV), P.O. Box 644, 48080 Bilbao, Basque Country (Spain)

    2013-03-01

    Acid drainage from coal mines and metal mining is a major source of underground and surface water contamination in the world. The coal mining acid drainage (CMAD) from mine contains large amount of solids in suspension and a high content of sulphate and dissolved metals (Al, Mn, Zn, Cu, Pb, Fe, etc.) that finally are deposited in the rivers. Since this problem can persist for centuries after mine abandonment, it is necessary to apply multidisciplinary methods to determine the potential risk in a determinate area. These multidisciplinary methods must include molecular and elemental analysis and finally all information must be studied statistically. This methodology was used in the case of coal mining acid drainage from the Tubarao River (Santa Catarina, Brazil). During molecular analysis, Raman Spectroscopy, electron bean, and X-ray diffraction (XRD) have been proven very useful for the study of minerals present in sediment rivers near this CMAD. The obtained spectra allow the precise identification of the minerals as jarosite, quartz, clays, etc. The elemental analysis (Al, As, Fe, K, Na, Ba, Mg, Mn, Ti, V, Zn, Ag, Co, Li, Mo, Ni, Se, Sn, W, B, Cr, Cu, Pb and Sr) was realised by inductively coupled plasma mass spectrometry (ICP-MS). Statistical analysis (Principal Component Analysis) of these dates of concentration reveals the existence of different groups of samples with specific pollution profiles in different areas of the Tubarao River. Highlights: ► Increasing coal drainage sediments geochemical information will increase human health information in this area. ► Brazilian coal mining information will increase recuperation planning information. ► The nanominerals showed strong sorption ability to aqueous hazardous elements.

  12. Study of environmental pollution and mineralogical characterization of sediment rivers from Brazilian coal mining acid drainage

    International Nuclear Information System (INIS)

    Silva, Luis F.O.; Fdez- Ortiz de Vallejuelo, Silvia; Martinez-Arkarazo, Irantzu; Castro, Kepa; Oliveira, Marcos L.S.; Sampaio, Carlos H.; Brum, Irineu A.S. de; Leão, Felipe B. de; Taffarel, Silvio R.; Madariaga, Juan M.

    2013-01-01

    Acid drainage from coal mines and metal mining is a major source of underground and surface water contamination in the world. The coal mining acid drainage (CMAD) from mine contains large amount of solids in suspension and a high content of sulphate and dissolved metals (Al, Mn, Zn, Cu, Pb, Fe, etc.) that finally are deposited in the rivers. Since this problem can persist for centuries after mine abandonment, it is necessary to apply multidisciplinary methods to determine the potential risk in a determinate area. These multidisciplinary methods must include molecular and elemental analysis and finally all information must be studied statistically. This methodology was used in the case of coal mining acid drainage from the Tubarao River (Santa Catarina, Brazil). During molecular analysis, Raman Spectroscopy, electron bean, and X-ray diffraction (XRD) have been proven very useful for the study of minerals present in sediment rivers near this CMAD. The obtained spectra allow the precise identification of the minerals as jarosite, quartz, clays, etc. The elemental analysis (Al, As, Fe, K, Na, Ba, Mg, Mn, Ti, V, Zn, Ag, Co, Li, Mo, Ni, Se, Sn, W, B, Cr, Cu, Pb and Sr) was realised by inductively coupled plasma mass spectrometry (ICP-MS). Statistical analysis (Principal Component Analysis) of these dates of concentration reveals the existence of different groups of samples with specific pollution profiles in different areas of the Tubarao River. Highlights: ► Increasing coal drainage sediments geochemical information will increase human health information in this area. ► Brazilian coal mining information will increase recuperation planning information. ► The nanominerals showed strong sorption ability to aqueous hazardous elements

  13. The safety regulation of small-scale coal mines in China: Analysing the interests and influences of stakeholders

    International Nuclear Information System (INIS)

    Song, Xiaoqian; Mu, Xiaoyi

    2013-01-01

    Small scale coal mines (SCMs) have played an important role in China’s energy supply. At the same time, they also suffer from many social, economic, environmental, and safety problems. The Chinese government has made considerable efforts to strengthen the safety regulation of the coal mining industry. Yet, few of these efforts have proven to be very effective. This paper analyzes the interests and influences of key stakeholders in the safety regulation of SCMs, which includes the safety regulator, the local government, the mine owner, and mineworkers. We argue that the effective regulation of coal mine safety must both engage and empower mineworkers. - Highlights: ► Small scale coal mines have played an important role in China's energy supply. ► We analyze the interests and influences of key stakeholders in the safety regulation of small coal mines. ► The mineworkers have the strongest interest but least influence. ► An effective regulation must engage the mineworkers, organize, and empower them.

  14. Barrier pillar between production panels in coal mine

    Energy Technology Data Exchange (ETDEWEB)

    Zingano, Andre Cezar; Koppe, Jair Carlos; Costa, Joao Felipe C.L. [Universidade Federal do Rio Grande do Sul, Porto Alegre (Brazil)

    2007-07-01

    The function of the barrier pillar is to protect the mining panel in activity from the abutment load of adjacent mining panels that were mined. In the case of underground mines in Santa Catarina State, the barrier pillar has functioned to protect the main entries of the mine against pillar failure from old mining panels. The objective of this paper is to verify the application of the empirical method to design barrier pillars as proposed by Peng (1986), using numerical simulation following the mining geometry of the coal mines in Santa Catarina State. Two-dimensional numerical models were built taking into account the geometry of the main entries and mining panels for different overburden thickness, and considering the geomechanical properties for the rock mass that forms the roof-pillar-floor system for the Bonito coal vein. The results of the simulations showed that the empirical method to determine the barrier pillar width is valid for the studied coal vein and considered mine geometry. Neither did the pillar at the main entry become overstressed due to adjacent mine panels, nor did the roof present any failure due to stress redistribution. 9 refs., 6 figs., 5 tabs.

  15. Coal mine subsidence: effects of mitigation on crop yields

    International Nuclear Information System (INIS)

    Darmody, R.G.; Hetzler, R.T.; Simmons, F.W.

    1992-01-01

    Subsidence from longwall underground coal mining adversely impacts agricultural land by creating wet or ponded areas. While most subsided areas show little impact, some localized places, usually less than 1.5 ha in size, may experience total crop failure. Coal companies mitigate subsidence damaged cropland by installing drainage waterways or by adding fill material to raise the grade. The objective of this study was to test the effectiveness of mitigation in restoring corn and soybean yields to pre-mined levels. Fourteen sites in southern Illinois were selected for study. Corn (Zea mays L.) and soybean (Glycine max L.) yields from mitigated and nearby undisturbed areas were compared for four years. Results varied due to differing weather and site conditions. Mean corn yields overall, however were significantly (α0.05) lower on mitigated areas. There was no significant difference in overall mean soybean yields. Soil fertility levels were similar and did not account for yield differences. 14 refs., 1 fig., 7 tabs

  16. Controlling ventilation for safe escape from coal mine fires

    Energy Technology Data Exchange (ETDEWEB)

    Wala, A M [University of Kentucky, Lexington, KY (United States). Mining Engineering Dept.

    1966-04-01

    If a fire occurs outby an underground coal mine section, the immediate safe evacuation of miners from the working section should always take precedence. Unfortunately, in many cases, the dedicated escapeway (escape routes) for the evacuation of the miners become contaminated by the byproducts of fire from the adjacent entries. The purpose of this paper is to present the ventilation-control process that would keep the escapeway free from contaminants and, thus, available for travel. A few scenarios of mine fires in longwall development panels are analysed and discussed. To perform these studies, a mine-fire simulator (MFS) was used. This (MFS) provides a dynamic representation of the fire`s progress (in real time) and gives a color-graphic visualization of the spready of oxygen, combustion products and temperature of the gases throughout the ventilation system. Also presented and discussed are ways in which the MFS can be used as a training and teaching tool for miners and particularly, for ventilation and safety specialists. 7 refs., 10 figs.

  17. 30 CFR 816.87 - Coal mine waste: Burning and burned waste utilization.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: Burning and burned waste...-SURFACE MINING ACTIVITIES § 816.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or burned coal mine waste shall be removed from a permitted disposal...

  18. Decontamination of coal mine effluent generated at the Rajrappa coal mine using phytoremediation technology.

    Science.gov (United States)

    Lakra, Kalpana C; Lal, B; Banerjee, T K

    2017-06-03

    Toxicity of the effluent generated at the Rajrappa coal mine complex under the Central Coalfields Limited (CCL, a subsidiary of Coal India Limited) in Jharkhand, India was investigated. The concentrations (mg L -1 ) of all the toxic metals (Fe, Mn, Ni, Zn, Cu, Pb, Cr, and Cd) in the coal mine effluent were above the safe limit suggested by the Environmental Protection Agency (EPA 2003). Among these, Fe showed the highest concentration (18.21 ± 3.865), while Cr had the lowest effluent concentration (0.15 ± 0.014). Efforts were also made to detoxify the effluent using two species of aquatic macrophytes namely "'Salvinia molesta and Pistia stratiotes." After 10 days of phytoremediation, S. molesta removed Pb (96.96%) > Ni (97.01%) > Cu (96.77%) > Zn (96.38%) > Mn (96.22%) > Fe (94.12%) > Cr (92.85%) > Cd (80.99%), and P. stratiotes removed Pb (96.21%) > Fe (94.34%) > Ni (92.53%) > Mn (85.24%) > Zn (79.51%) > Cr (78.57%) > Cu (74.19%) > Cd (72.72%). The impact of coal mine exposure on chlorophyll content showed a significant decrease of 42.49% and 24.54% from control values in S. molesta and P. stratiotes, respectively, perhaps due to the damage inflicted by the toxic metals, leading to the decay of plant tissues.

  19. ANFO bulk loading in coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Gajjar, A.

    1987-08-01

    With India's total coal production projected to increase from 152 to 237 million tons by 1990, net additional production from new mines must be more because of substantial depletion in existing mines. This article discusses the best possible application of explosive techniques in open-cast coal mines to economize production cost. The most energy-efficient and safest explosive is ANFO (ammonium nitrate, fuel oil); however, manual charging by INFO is not possible. Therefore, the solution is the application of bulk-loading systems of ANFO for giant mining operations. Cost of blasting per ton of coal production in India is in the range of Rs 25. Thus, the author suggests it will be the responsibility of mining engineers to see that the ANFO based bulk-loading system is implemented and the cost of production per ton reduced to Rs 19.50.

  20. Pneumatic automation systems in coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Shmatkov, N.A.; Kiklevich, Yu.N.

    1981-04-01

    Giprougleavtomatizatsiya, Avtomatgormash, Dongiprouglemash, VNIIGD and other plants develop 30 new pneumatic systems for mine machines and equipment control each year. The plants produce about 200 types of pneumatic systems. Major pneumatic systems for face systems, machines and equipment are reviewed: Sirena system for remote control of ANShch and AShchM face systems for steep coal seams, UPS control systems for pump stations, PAUZA control system for stowing machines, remote control system of B100-200 drilling machines, PUSK control system for coal cutter loaders with pneumatic drive (A-70, Temp), PUVSh control system for ventilation barriers activated from moving electric locomotives, PAZ control system for skip hoist loading. Specifications of the systems are given. Economic benefit produced by the pneumatic control systems are evaluated (from 1,500 to 40,000 rubles/year). Using the systems increases productivity of face machines and other machines used in black coal mines by 5 to 30%.

  1. Conversion of Coal Mine Gas to LNG

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2016-02-05

    This project evolved from a 1995, DOE-NETL competitive solicitation for practical CMM capture and utilization concepts. Appalachian Pacific was one of three companies selected to proceed with the construction and operation of a cost-shared demonstration plant. In the course of trying to proceed with this demonstration plant, AP examined several liquefaction technologies, discussed obtaining rights to coal mine methane with a number of coal companies, explored marketing potential with a wide variety of customers in many sections of the United States, studied in great detail the impact of a carbon credit exchange, and developed a suite of analytical tools with which to evaluate possible project options. In the end, the newness of the product, reluctance on the part of the coal companies to venture away from time tested practices, difficulty with obtaining financing, the failure of a carbon credit market to develop and the emergence of shale derived gas production prevented a demonstration plant from being built.

  2. Response of plant species to coal-mine soil materials

    Energy Technology Data Exchange (ETDEWEB)

    Day, A.D.; Tucker, T.C.; Thames, J.L.

    1983-03-01

    The two-year Black Mesa Coal Mine Research Study on the area near Kayenta, Arizona investigating the growth and establishment of seven plant species in unmined soil and coal-mined soils found that plant species grew better in unmined soil and that irrigation is essential during seedling establishment for the effective stabilization of coal-mined soils in a semi-arid environment. Differences among the species included variations in germination, response to irrigation, seedling establishment, and stem growth. 12 references, 2 figures, 2 tables.

  3. Anchor-Free Localization Method for Mobile Targets in Coal Mine Wireless Sensor Networks

    Directory of Open Access Journals (Sweden)

    Xiao Xu

    2009-04-01

    Full Text Available Severe natural conditions and complex terrain make it difficult to apply precise localization in underground mines. In this paper, an anchor-free localization method for mobile targets is proposed based on non-metric multi-dimensional scaling (Multi-dimensional Scaling: MDS and rank sequence. Firstly, a coal mine wireless sensor network is constructed in underground mines based on the ZigBee technology. Then a non-metric MDS algorithm is imported to estimate the reference nodes’ location. Finally, an improved sequence-based localization algorithm is presented to complete precise localization for mobile targets. The proposed method is tested through simulations with 100 nodes, outdoor experiments with 15 ZigBee physical nodes, and the experiments in the mine gas explosion laboratory with 12 ZigBee nodes. Experimental results show that our method has better localization accuracy and is more robust in underground mines.

  4. Anchor-free localization method for mobile targets in coal mine wireless sensor networks.

    Science.gov (United States)

    Pei, Zhongmin; Deng, Zhidong; Xu, Shuo; Xu, Xiao

    2009-01-01

    Severe natural conditions and complex terrain make it difficult to apply precise localization in underground mines. In this paper, an anchor-free localization method for mobile targets is proposed based on non-metric multi-dimensional scaling (Multi-dimensional Scaling: MDS) and rank sequence. Firstly, a coal mine wireless sensor network is constructed in underground mines based on the ZigBee technology. Then a non-metric MDS algorithm is imported to estimate the reference nodes' location. Finally, an improved sequence-based localization algorithm is presented to complete precise localization for mobile targets. The proposed method is tested through simulations with 100 nodes, outdoor experiments with 15 ZigBee physical nodes, and the experiments in the mine gas explosion laboratory with 12 ZigBee nodes. Experimental results show that our method has better localization accuracy and is more robust in underground mines.

  5. Latest developments in the utilization of coal mining wastes

    Energy Technology Data Exchange (ETDEWEB)

    Canibano, J G [HUNOSA, Oviedo (Spain)

    1996-12-31

    This report summarizes recent studies carried out on coal mining wastes (minestones) of Spain. These studies proved that such wastes can be used as filling materials in reinforced earth structures, capping layers of roads, substratum in hydroponic cultures and fuel.

  6. Analysis on safety production in coal mines Henan Province

    Institute of Scientific and Technical Information of China (English)

    KONG Liu-an; ZHANG Wen-yong

    2006-01-01

    Based on the rigorous situation of safety production in coal mines, the paper analyzed the statistical data of recent accidents indexes in Henan's coal mines. Using investigation and comparison analysis methods, a specified analysis on mining conditions, technical facility level, safety input and vocational quality of workers in Henan's coal mines was conducted. The result indicates that there have been existing such main safety production problems as weak safety management, low-level facilities, inadequate safety input and poor vocational quality and so on. Finally it proposes such reference solutions as to establish and perfect coal mining supervision and management system, to increase safety investment into techniques and facilities and to strengthen workers' safety education and introduction of more high-level professional talents.

  7. Computerization of administration and operation management in Polish black coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Mastej, R.; Syrkiewicz, J. (Centralny Osrodek Informatyki Gornictwa (Poland))

    1990-08-01

    Characterizes main solutions of the computerized management model adopted in Poland for the mining industry and the technical and oganizational structure of computer system application. Computer systems for black coal mines and the range of microprocessor application are shown in block diagrams. The COIG mining information center makes about 45 computer system modules with independent implementation available for black coal mines. The general concept foresees central data processing in the COIG center on the ODRA 1305 and ICL 297 computers with the G-3 operating system in the first stage and an ICL series 39 computer with the VME operating system in the second stage. For mines where no transmission lines are available local solutions based on smaller ICL computers, minicomputers or computer networks with the NOVELL network operating system or multi-access systems with the UNIX operating system are planned. 3 refs.

  8. Coal mine enterprise integration based on strategic alliance

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Q.; Sun, J.; Xu, S. [Tsinghua University, Beijing (China). Dept. of Computer Science and Technology

    2003-07-01

    The relationship between coal mine and related enterprise was analysed. Aiming at the competitive world market as well as the dynamic requirement, a coal mine enterprise integration strategy and a enterprise strategic alliance were proposed for the product providing service business pattern. The modelling method of the enterprise strategic alliance was proposed, including the relationship view model, information view model and business process view model. The idea of enterprise strategic alliance is useful for enterprise integration. 6 refs., 2 figs.

  9. Mining engineer requirements in a German coal mine

    Energy Technology Data Exchange (ETDEWEB)

    Rauhut, F J

    1985-10-01

    Basic developments in German coal mines, new definitions of working areas of mining engineers, and groups of requirements in education are discussed. These groups include: requirements of hard-coal mining at great depth and in extended collieries; application of process technology and information systems in semi-automated mines; thinking in processes and systems; organizational changes; future requirements of mining engineers; responsibility of the mining engineer for employees and society.

  10. Selective bibliography of surface coal mining and reclamation literature. Volume 1. Eastern coal province. [More than 1300 references

    Energy Technology Data Exchange (ETDEWEB)

    Weiss, N. E.; Sobek, A. A.; Streib, D. L.

    1977-11-01

    This bibliography has been compiled for use by researchers, students, and other groups who need a reference source of published literature related to surface coal mining and reclamation in the Eastern Coal Province. This bibliography contains more than 1300 references including government reports, journal articles, symposium proceedings, industrial reports, workshop proceedings, theses, and bibliographices. A simple format was used to categorize citations.

  11. Down-scaling of bituminous coal mining, restructuring of steel works and heavy engineering in the Ostrava region

    Czech Academy of Sciences Publication Activity Database

    Klusáček, Petr

    2005-01-01

    Roč. 13, č. 2 (2005), s. 3-12 ISSN 1210-8812 R&D Projects: GA AV ČR(CZ) IBS3086005 Institutional research plan: CEZ:AV0Z30860518 Keywords : Ostrava region * restructuring * steemaking and heavy industry * downscaling of coal-mining Subject RIV: DE - Earth Magnetism, Geodesy, Geography

  12. 30 CFR 75.804 - Underground high-voltage cables.

    Science.gov (United States)

    2010-07-01

    ... AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Underground High-Voltage Distribution § 75.804 Underground high-voltage cables. (a) Underground high-voltage cables used in resistance... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Underground high-voltage cables. 75.804 Section...

  13. Residential damage in an area of underground coal mining

    International Nuclear Information System (INIS)

    Padgett, M.F.

    1988-01-01

    In order to estimate the potential for future subsidence-related residential damage, a statistical analysis of past residential damage in the Boulder-Weld, Colorado, coal field was performed. The objectives of this study were to assess the difference in damage severity and frequency between undermined and non-undermined areas, and to determine, where applicable, which mining factors significantly influence the severity and frequency of residential damage. The results of this study suggest that undermined homes have almost three times the risk of having some type of structural damage than do non-undermined homes. The study also indicated that both geologic factors, such as the ratio of sandstone/claystone in the overburden, and mining factors, such as the mining feature (room, pillar, entry, etc.), can significantly affect the severity of overlying residential damage. However, the results of this study are dependent on local conditions and should not be applied elsewhere unless the geologic, mining, and residential conditions are similar

  14. 78 FR 48593 - Refuge Alternatives for Underground Coal Mines

    Science.gov (United States)

    2013-08-08

    ... information on the availability, use, and cost of air conditioning units in refuge alternatives to control...://www.msha.gov/subscriptions/subscribe.aspx . I. Statutory and Regulatory History The Mine Improvement... dioxide scrubbing when breathable air is supplied through a borehole or piping from the surface. A. Miner...

  15. Inertisation strategies and practices in underground coal mines.

    CSIR Research Space (South Africa)

    Du Plessis, JJL

    2002-01-01

    Full Text Available of the BVS triggered barrier system.....................................64 Figure 7.1e: Mobile automatic multiple-extinguisher system (BVS) .............................65 Figure 7.1f: Sensors evaluated for the development of a ‘European triggered barrier....e. large proportion of the employees are exposed to these hazards; • it may consist of numerous headings without effective through ventilation i.e. “blind headings”; • headings advance intermittently albeit rapidly with time; • coal fragmentation...

  16. Dermatoses of Belchatow brown coal mine employees

    Energy Technology Data Exchange (ETDEWEB)

    Ruszczak, Z.; Bienias, L.; Proszczynska-Kuczynska, W.

    1981-09-01

    Evaluates the results of examinations carried out in the Belchatow brown coal surface mine on skin diseases. Influence of working conditions specific for brown coal mines on the development of some dermatoses is analyzed. From 1978 to 1979 443 miners were examined. Two groups of miners were examined separately: 1. 235 miners who contacted the firm physician due to skin problems and 2. 208 miners who underwent a periodic examination. In group 1 skin dermatoses were found in 86% of all cases, and in group 2 in 48%. Foot skin inflammation, particularly interdigital intertrigo, was the most common dermatosis. Oil acne (occupational disease of coal miners) was diagnosed in 15 cases, common acne in 23 cases, pytiriasis versicolor in 19 cases, erythrasma in 10, eczema and other contact dermatitis in 10 cases. Investigations show that 23% of the foot interdigital intertrigo is caused by mycotic infections. Dermatoses of the skin of miners' feet are caused mainly by rubber protective boots. (10 refs.) (In Polish)

  17. Microbial ecology of coal mine refuse

    Energy Technology Data Exchange (ETDEWEB)

    Cameron, R. E.; Miller, R. M.

    1977-01-01

    Baseline microbial and ecological studies of samples obtained from two abandoned coal mine refuse sites in the State of Illinois indicate that the unfavorable nature of refuse materials can be a very limiting factor for survival and growth of organisms. Despite the ''foothold'' obtained by some microorganisms, especially acidophilic fungi and some acidotolerant algae, the refuse materials should be amended or ameliorated to raise the pH, provide needed nutrients, especially nitrogen, and provide biodegradable organic matter, both for physical and biological purposes. Finally, the role of microbial populations, responses, and interactions in acid mine wastes must be put into larger perspective. Acid mine drainage amounts to over 4 million tons per year of acidity from active and abandoned mines. Microorganisms appear to be significantly responsible for this problem, but they also can play a beneficial and significant role in the amelioration or alleviation of this detrimental effect as abandoned mines are reclaimed and returned to useful productivity.

  18. Dermatoses of Belchatow brown coal mine employees

    Energy Technology Data Exchange (ETDEWEB)

    Ruszczak, Z; Bienias, L; Proszczynska-Kuczynska, W

    1981-09-01

    Evaluates the results of examinations carried out in the Belchatow brown coal surface mine on skin diseases. Influence of working conditions specific for brown coal mines on the development of some dermatoses is analyzed. From 1978 to 1979 443 miners were examined. Two groups of miners were examined separately: 1. 235 miners who contacted the firm physician due to skin problems and 2. 208 miners who underwent a periodic examination. In group 1 skin dermatoses were found in 86% of all cases, and in group 2 in 48%. Foot skin inflammation, particularly interdigital intertrigo, was the most common dermatosis. Oil acne (occupational disease of coal miners) was diagnosed in 15 cases, common acne in 23 cases, pytiriasis versicolor in 19 cases, erythrasma in 10, eczema and other contact dermatitis in 10 cases. Investigations show that 23% of the foot interdigital intertrigo is caused by mycotic infections. Dermatoses of the skin of miners' feet are caused mainly by rubber protective boots. (10 refs.) (In Polish)

  19. Environmental management zoning for coal mining in mainland China based on ecological and resources conditions.

    Science.gov (United States)

    Geng, Haiqing; Chen, Fan; Wang, Zhiyuan; Liu, Jie; Xu, Weihua

    2017-05-01

    The purpose of this research is to establish an environmental management zoning for coal mining industry which is served as a basis for making environmental management policies. Based on the specific impacts of coal mining and regional characteristics of environment and resources, the ecological impact, water resources impact, and arable land impact are chose as the zoning indexes to construct the index system. The ecological sensitivity is graded into three levels of low, medium, and high according to analytical hierarchy processes and gray fixed weight clustering analysis, and the water resources sensitivity is divided into five levels of lower, low, medium, high, and higher according to the weighted sum of sub-indexes, while only the arable land sensitive zone was extracted on the basis of the ratio of arable land to the county or city. By combining the ecological sensitivity zoning and the water resources sensitive zoning and then overlapping the arable-sensitive areas, the mainland China is classified into six types of environmental management zones for coal mining except to the forbidden exploitation areas.

  20. Comparative study on efficiency performance of listed coal mining companies in China and the US

    International Nuclear Information System (INIS)

    Fang, Hong; Wu, Junjie; Zeng, Catherine

    2009-01-01

    Continually rising energy prices in global markets highlights a serious concern about the need to improve energy efficiency and the efficiency in energy sector in many countries. China, as one of the fastest growing countries in the world and the largest coal producer, has high coal consumption but a low recovery rate of coal utilization. Coal efficiency and the efficiency in coal industry have therefore attracted a great deal of attention from Chinese policy makers, coal firms and academics. This study attempts to compare the relative technical efficiency performance of listed coal mining companies in China and the US using CCR and BCC models in the advanced DEA linear programming. The results show that the level of relative efficiency in Chinese coal mining enterprises, regardless of total technical efficiency or decomposed pure technical and scale efficiency, is much lower than in American coal firms. The study also highlights the input resources that cause the inefficiency of Chinese coal mining companies. Furthermore, in-depth discussion and analysis of how the institutional environments of the two countries could cause the differences are provided. (author)

  1. An Approach for Understanding and Promoting Coal Mine Safety by Exploring Coal Mine Risk Network

    Directory of Open Access Journals (Sweden)

    Yongliang Deng

    2017-01-01

    Full Text Available Capturing the interrelations among risks is essential to thoroughly understand and promote coal mining safety. From this standpoint, 105 risks and 135 interrelations among risks had been identified from 126 typical accidents, which were also the foundation of constructing coal mine risk network (CMRN. Based on the complex network theory and Pajek, six parameters (i.e., network diameter, network density, average path length, degree, betweenness, and clustering coefficient were employed to reveal the topological properties of CMRN. As indicated by the results, CMRN possesses scale-free network property because its cumulative degree distribution obeys power-law distribution. This means that CMRN is robust to random hazard and vulnerable to deliberate attack. CMRN is also a small-world network due to its relatively small average path length as well as high clustering coefficient, implying that accident propagation in CMRN is faster than regular network. Furthermore, the effect of risk control is explored. According to the result, it shows that roof collapse, fire, and gas concentration exceeding limit refer to three most valuable targets for risk control among all the risks. This study will help offer recommendations and proposals for making beforehand strategies that can restrain original risks and reduce accidents.

  2. Miners' return to work following injuries in coal mines.

    Science.gov (United States)

    Bhattacherjee, Ashis; Kunar, Bijay Mihir

    2016-12-22

    The occupational injuries in mines are common and result in severe socio-economical consequences. Earlier studies have revealed the role of multiple factors such as demographic factors, behavioral factors, health-related factors, working environment, and working conditions for mine injuries. However, there is a dearth of information about the role of some of these factors in delayed return to work (RTW) following a miner's injury. These factors may likely include personal characteristics of injured persons and his or her family, the injured person's social and economic status, and job characteristics. This study was conducted to assess the role of some of these factors for the return to work following coal miners' injuries. A study was conducted for 109 injured workers from an underground coal mine in the years 2000-2009. A questionnaire, which was completed by the personnel interviews, included among others age, height, weight, seniority, alcohol consumption, sleeping duration, presence of diseases, job stress, job satisfaction, and injury type. The data was analyzed using the Kaplan-Meier estimates and the Cox proportional hazard model. According to Kaplan-Meier estimate it was revealed that a lower number of dependents, longer sleep duration, no job stress, no disease, no alcohol addiction, and higher monthly income have a great impact on early return to work after injury. The Cox regression analysis revealed that the significant risk factors which influenced miners' return to work included presence of disease, job satisfaction and injury type. The mine management should pay attention to significant risk factors for injuries in order to develop effective preventive measures. Med Pr 2016;67(6):729-742. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

  3. Miners’ return to work following injuries in coal mines

    Directory of Open Access Journals (Sweden)

    Ashis Bhattacherjee

    2016-12-01

    Full Text Available Background: The occupational injuries in mines are common and result in severe socio-economical consequences. Earlier studies have revealed the role of multiple factors such as demographic factors, behavioral factors, health-related factors, working environment, and working conditions for mine injuries. However, there is a dearth of information about the role of some of these factors in delayed return to work (RTW following a miner’s injury. These factors may likely include personal characteristics of injured persons and his or her family, the injured person’s social and economic status, and job characteristics. This study was conducted to assess the role of some of these factors for the return to work following coal miners’ injuries. Material and Methods: A study was conducted for 109 injured workers from an underground coal mine in the years 2000–2009. A questionnaire, which was completed by the personnel interviews, included among others age, height, weight, seniority, alcohol consumption, sleeping duration, presence of diseases, job stress, job satisfaction, and injury type. The data was analyzed using the Kaplan-Meier estimates and the Cox proportional hazard model. Results: According to Kaplan-Meier estimate it was revealed that a lower number of dependents, longer sleep duration, no job stress, no disease, no alcohol addiction, and higher monthly income have a great impact on early return to work after injury. The Cox regression analysis revealed that the significant risk factors which influenced miners’ return to work included presence of disease, job satisfaction and injury type. Conclusions: The mine management should pay attention to significant risk factors for injuries in order to develop effective preventive measures. Med Pr 2016;67(6:729–742

  4. Priority pollutants and associated constituents in untreated and treated discharges from coal mining or processing facilities in Pennsylvania, USA

    Science.gov (United States)

    Cravotta, III, Charles A.; Brady, Keith B.C.

    2015-01-01

    Clean sampling and analysis procedures were used to quantify more than 70 inorganic constituents, including 35 potentially toxic or hazardous constituents, organic carbon, and other characteristics of untreated (influent) and treated (effluent) coal-mine discharges (CMD) at 38 permitted coal-mining or coal-processing facilities in the bituminous coalfield and 4 facilities in the anthracite coalfield of Pennsylvania. Of the 42 facilities sampled during 2011, 26 were surface mines, 11 were underground mines, and 5 were coal refuse disposal operations. Treatment of CMD with caustic soda (NaOH), lime (CaO or Ca(OH)2), flocculent, or limestone was ongoing at 21%, 40%, 6%, and 4% of the facilities, respectively; no chemicals were added at the remaining facilities. All facilities with CMD treatment incorporated structures for active or passive aeration and settling of metal-rich precipitate.

  5. Technogenic effect of liquidation of coal mines on earth’s entrails: hydrogeochemical aspect

    Science.gov (United States)

    Tarasenko, I. A.; Zinkov, A. V.; Chudaev, O. V.; Vetoshkina, A. V.; Holodilov, I. I.

    2017-10-01

    The authors of the paper have established the geochemical features of the composition of underground waters and regularities of their formation in the areas of the liquidated coal mines of Russia and Ukraine. It is shown that the mine flood resulted in the formation of technogenic waters which geochemical specificity originates in the feeding field and is transformed in the direction of the filtration flow. It depends on the geological structure of sedimentary basins and the presence in the coal and supra-coal beds of the marine, salt-bearing and freshwater groups of geological formations. The water types are distinguished characterizing the conditions and processes of their formation that may be the regional markers in the hydrochemical and geological constructions. The technogenic waters influenced the safety of the underground waters, sources of water supply of the regions, and surface water channels. The pollutions are of local character in space.

  6. Open-pit coal mine production sequencing incorporating grade blending and stockpiling options: An application from an Indian mine

    Science.gov (United States)

    Kumar, Ashish; Chatterjee, Snehamoy

    2017-05-01

    Production scheduling is a crucial aspect of the mining industry. An optimal and efficient production schedule can increase the profits manifold and reduce the amount of waste to be handled. Production scheduling for coal mines is necessary to maintain consistency in the quality and quantity parameters of coal supplied to power plants. Irregularity in the quality parameters of the coal can lead to heavy losses in coal-fired power plants. Moreover, the stockpiling of coal poses environmental and fire problems owing to low incubation periods. This article proposes a production scheduling formulation for open-pit coal mines including stockpiling and blending opportunities, which play a major role in maintaining the quality and quantity of supplied coal. The proposed formulation was applied to a large open-pit coal mine in India. This contribution provides an efficient production scheduling formulation for coal mines after utilizing the stockpile coal within the incubation periods with the maximization of discounted cash flows. At the same time, consistency is maintained in the quality and quantity of coal to power plants through blending and stockpiling options to ensure smooth functioning.

  7. International mining forum 2004, new technologies in underground mining, safety in mines proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Jerzy Kicki; Eugeniusz Sobczyk (eds.)

    2004-01-15

    The book comprises technical papers that were presented at the International Mining Forum 2004. This event aims to bring together scientists and engineers in mining, rock mechanics, and computer engineering, with a view to explore and discuss international developments in the field. Topics discussed in this book are: trends in the mining industry; new solutions and tendencies in underground mines; rock engineering problems in underground mines; utilization and exploitation of methane; prevention measures for the control of rock bursts in Polish mines; and current problems in Ukrainian coal mines.

  8. Coal mining and the resource community cycle: A longitudinal assessment of the social impacts of the Coppabella coal mine

    Energy Technology Data Exchange (ETDEWEB)

    Lockie, S.; Franettovich, M.; Petkova-Timmer, V.; Rolfe, J.; Ivanova, G. [CQUniversity of Australia, Rockhampton, Qld. (Australia). Inst. of Health & Social Science Research

    2009-09-15

    Two social impact assessment (SIA) studies of Central Queensland's Coppabella coal mine were undertaken in 2002-2003 and 2006-2007. As ex post studies of actual change, these provide a reference point for predictive assessments of proposed resource extraction projects at other sites, while the longitudinal element added by the second study illustrates how impacts associated with one mine may vary over time due to changing economic and social conditions. It was found that the traditional coupling of local economic vitality and community development to the life cycle of resource projects - the resource community cycle - was mediated by labour recruitment and social infrastructure policies that reduced the emphasis on localised employment and investment strategies. and by the cumulative impacts of multiple mining projects within relative proximity to each other. The resource community cycle was accelerated and local communities forced to consider ways of attracting secondary investment and/or alternative industries early in the operational life of the Coppabella mine in order to secure significant economic benefits and to guard against the erosion of social capital and the ability to cope with future downturns in the mining sector.

  9. Coal mining and the resource community cycle: A longitudinal assessment of the social impacts of the Coppabella coal mine

    International Nuclear Information System (INIS)

    Lockie, Stewart; Franettovich, Maree; Petkova-Timmer, Vanessa; Rolfe, John; Ivanova, Galina

    2009-01-01

    Two social impact assessment (SIA) studies of Central Queensland's Coppabella coal mine were undertaken in 2002-2003 and 2006-2007. As ex post studies of actual change, these provide a reference point for predictive assessments of proposed resource extraction projects at other sites, while the longitudinal element added by the second study illustrates how impacts associated with one mine may vary over time due to changing economic and social conditions. It was found that the traditional coupling of local economic vitality and community development to the life cycle of resource projects-the resource community cycle-was mediated by labour recruitment and social infrastructure policies that reduced the emphasis on localised employment and investment strategies, and by the cumulative impacts of multiple mining projects within relative proximity to each other. The resource community cycle was accelerated and local communities forced to consider ways of attracting secondary investment and/or alternative industries early in the operational life of the Coppabella mine in order to secure significant economic benefits and to guard against the erosion of social capital and the ability to cope with future downturns in the mining sector.

  10. Aquatic ecosystems in the coal mining landscape of the upper Olifants River, and the way forward

    CSIR Research Space (South Africa)

    Oberholster, Paul J

    2014-03-01

    Full Text Available can provide guidance on managing water ecosystems in the future at various stages of mining operations, which include understanding the interface between water ecosystems and coal mining activities, assessing the likelihood of coal mining activities...

  11. British Managing Agencies in Indian coal mining, 1893-1918

    Energy Technology Data Exchange (ETDEWEB)

    Papendieck, H

    1975-09-01

    The role of British managing agencies in Bengal coal mining at the turn of the century is reviewed. The consequences of the managing agency system as a form of capital organisation in Bengal on the goals and rate of industrialisation in Bengal (and in India) are investigated for the example of coal mining. After a historical outline, the development of Indian coal mining, the organisational structure of the managing agencies, the structure of on average Indian colliery at the turn of the century, and the development of the Andrew Yule and Co. Managing Agency are discussed. The behaviour of the Katras-Jherria Coal Company and its associates, the Bengal Coal Company, and the consequency system on Bengal's economic development are described.

  12. Environmental impact assessment for surface coal mine - a case study

    International Nuclear Information System (INIS)

    Sen, P.; Chakraborty, K.

    1994-01-01

    Surface coal mines being the largest contributor to the national coal production, the study of environmental impacts due to this becomes mandatory as it will help in proper planning and safe operations of the mine in an environmentally compatible manner. Within the scope of this paper, a model for preparation of comprehensive environmental impact assessment (EIA) by utilising a new evaluation methodology leading to determination of Environmental Quality Designation an index has been developed and this model has been validated by using data from a running surface coal mine in Wardha Valley Coalfield. Based on this exercise, the overall impact of the surface coal mine under consideration on environment indicates a medium level and accordingly the control measures have to be planned. Thus repair to the environment has to be made a concurrent activity with mining i.e. to say we have to design with nature not against it

  13. Lung disease and coal mining: what pulmonologists need to know.

    Science.gov (United States)

    Go, Leonard H T; Krefft, Silpa D; Cohen, Robert A; Rose, Cecile S

    2016-03-01

    Coal mine workers are at risk for a range of chronic respiratory diseases including coal workers' pneumoconiosis, diffuse dust-related fibrosis, and chronic obstructive pulmonary disease. The purpose of this review is to describe coal mining processes and associated exposures to inform the diagnostic evaluation of miners with respiratory symptoms. Although rates of coal workers' pneumoconiosis declined after regulations were enacted in the 1970s, more recent data shows a reversal in this downward trend. Rapidly progressive pneumoconiosis with progressive massive fibrosis (complicated coal workers' pneumoconiosis) is being observed with increased frequency in United States coal miners, with histologic findings of silicosis and mixed-dust pneumoconiosis. There is increasing evidence of decline in lung function in individuals with pneumoconiosis. Multiple recent cohort studies suggest increased risk of lung cancer in coal miners. A detailed understanding of coal mining methods and processes allows clinicians to better evaluate and confirm chronic lung diseases caused by inhalational hazards in the mine atmosphere.

  14. 4D seismic data acquisition method during coal mining

    International Nuclear Information System (INIS)

    Du, Wen-Feng; Peng, Su-Ping

    2014-01-01

    In order to observe overburden media changes caused by mining processing, we take the fully-mechanized working face of the BLT coal mine in Shendong mine district as an example to develop a 4D seismic data acquisition methodology during coal mining. The 4D seismic data acquisition is implemented to collect 3D seismic data four times in different periods, such as before mining, during the mining process and after mining to observe the changes of the overburden layer during coal mining. The seismic data in the research area demonstrates that seismic waves are stronger in energy, higher in frequency and have better continuous reflectors before coal mining. However, all this is reversed after coal mining because the overburden layer has been mined, the seismic energy and frequency decrease, and reflections have more discontinuities. Comparing the records collected in the survey with those from newly mined areas and other records acquired in the same survey with the same geometry and with a long time for settling after mining, it clearly shows that the seismic reflections have stronger amplitudes and are more continuous because the media have recovered by overburden layer compaction after a long time of settling after mining. By 4D seismic acquisition, the original background investigation of the coal layers can be derived from the first records, then the layer structure changes can be monitored through the records of mining action and compaction action after mining. This method has laid the foundation for further research into the variation principles of the overburden layer under modern coal-mining conditions. (paper)

  15. The Economic Impact of Coal Mining in New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Peach, James; Starbuck, C.

    2009-06-01

    The economic impact of coal mining in New Mexico is examined in this report. The analysis is based on economic multipliers derived from an input-output model of the New Mexico economy. The direct, indirect, and induced impacts of coal mining in New Mexico are presented in terms of output, value added, employment, and labor income for calendar year 2007. Tax, rental, and royalty income to the State of New Mexico are also presented. Historical coal production, reserves, and price data are also presented and discussed. The impacts of coal-fired electricity generation will be examined in a separate report.

  16. Coal mining situation in the Federal Republic of Germany. The 1st quarter 2010

    International Nuclear Information System (INIS)

    2010-01-01

    The report on coal mining situation in the Federal Republic of Germany in the 1st quarter 2010 contains the statistical data concerning the following issues: (i) black coal mining: part I: production, resources, accomplishments; employees, part II: marketing and foreign trade; (ii) brown coal mining: part I: production, resources, accomplishments; employees, part II: marketing and foreign trade.

  17. 29 CFR 570.53 - Coal-mine occupations (Order 3).

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Coal-mine occupations (Order 3). 570.53 Section 570.53... § 570.53 Coal-mine occupations (Order 3). (a) Finding and declaration of fact. All occupations in or about any coal mine, except the occupation of slate or other refuse picking at a picking table or...

  18. 78 FR 45566 - Agency Information Collection Activities; Submission for OMB Review; Comment Request; Coal Mine...

    Science.gov (United States)

    2013-07-29

    ... for OMB Review; Comment Request; Coal Mine Dust Sampling Devices ACTION: Notice. SUMMARY: The... information collection request (ICR) titled, ``Coal Mine Dust Sampling Devices,'' to the Office of Management...) determine the concentration of respirable dust in coal mines. CPDMs must be designed and constructed for...

  19. 76 FR 10070 - Division of Coal Mine Workers' Compensation; Proposed Extension of Existing Collection; Comment...

    Science.gov (United States)

    2011-02-23

    ... DEPARTMENT OF LABOR Office of Workers' Compensation Programs Division of Coal Mine Workers... Rereading (CM-933b), Medical History and Examination for Coal Mine Workers' Pneumoconiosis (CM-988), Report... interpretation of x-rays. When a miner applies for benefits, the Division of Coal Mine Workers' Compensation...

  20. The effects of ambient conditions on the passive dust sampler when used in coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Hemingway, M.; Thorpe, A.

    1998-09-01

    A previous feasibility study of the Health and Safety Laboratory (HSL) electret-based passive dust sampler carried out during site sampling in coal mines showed that the measurements made with the passive sampler and those made with the MRE sampler correlated well in each of two mines, but the ratios of samples obtained with the passive sampler and the MRE sampler in the two mines were different. This means the passive sampler would need a separate calibration for each coal mine in which it was used. Laboratory tests and further underground trials were carried out to quantify the possible effects of temperature and humidity on ratios. The passive dust samplers used at Maltby Colliery in the UK were found to pass the acceptance criteria according to the CEN standard for the assessment of the performance of instruments for the measurement of airborne particles, provided that samplers exposed when coal was not being cut were not included in the analysis. Temperature and relative humidity slightly affected the behaviour of the passive sampler during laboratory trials and relative humidity was found to possibly affect the behaviour during field trials. Ventilation rates had no effect on the passive sampler behaviour but the orientation of the passive dust sampler with respect to air flow affected the behaviour during laboratory trials. Further work is needed to quantify effects. 7 refs., 14 figs., 3 tabs.

  1. Development of effective means of propaganda of safety techniques for coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Galushko, A.L.; Brusilovskiy, V.I.; Popov, I.I.

    1979-01-01

    Information letters about accidents in coal mines are systematically developed and sent to enterprises and organizations of the branch for practical use in preventive work on work protection and work safety. Information materials on advanced experience in prevention of accidents and traumatism are published in large quantities. Principal measures which have dramatically affected the reduction of the level of production traumatism are listed which merit dissemination in the branch. It is noted that the use of these means of propaganda of work safety makes it possible to improve preventive work on work safety and production sanitation in enterprises of the coal industry.

  2. Experience of creating a multifunctional safety system at the coal mining enterprise

    Science.gov (United States)

    Reshetnikov, V. V.; Davkaev, K. S.; Korolkov, M. V.; Lyakhovets, M. V.

    2018-05-01

    The principles of creating multifunctional safety systems (MFSS) based on mathematical models with Markov properties are considered. The applicability of such models for the analysis of the safety of the created systems and their effectiveness is substantiated. The method of this analysis and the results of its testing are discussed. The variant of IFSB implementation in the conditions of the operating coal-mining enterprise is given. The functional scheme, data scheme and operating modes of the MFSS are given. The automated workplace of the industrial safety controller is described.

  3. The Concept of Resource Use Efficiency as a Theoretical Basis for Promising Coal Mining Technologies

    Science.gov (United States)

    Mikhalchenko, Vadim

    2017-11-01

    The article is devoted to solving one of the most relevant problems of the coal mining industry - its high resource use efficiency, which results in high environmental and economic costs of operating enterprises. It is shown that it is the high resource use efficiency of traditional, historically developed coal production systems that generates a conflict between indicators of economic efficiency and indicators of resistance to uncertainty and variability of market environment parameters. The traditional technological paradigm of exploitation of coal deposits also predetermines high, technology-driven, economic risks. The solution is shown and a real example of the problem solution is considered.

  4. 75 FR 17511 - Coal Mine Dust Sampling Devices

    Science.gov (United States)

    2010-04-06

    ... base and free to oscillate at its narrow or free end on which the collection filter is mounted... coal mines from power stations, electric motors and remote control transmitters. The final rule... electromagnetic interference. The FCC is an independent Federal agency that regulates radiofrequency emitting...

  5. Coal mining in Spain: first half year 1986

    Energy Technology Data Exchange (ETDEWEB)

    1986-01-01

    Statistical data from the first half of 1986 on coal mining in Spain. These figures cover anthracite, bituminous coal and lignite both nationally and for the coal-producing regions of Leon, Asturias, Palencia, Teruel and La Coruna. Special attention is paid to absenteeism and its causes.

  6. 30 CFR 816.84 - Coal mine waste: Impounding structures.

    Science.gov (United States)

    2010-07-01

    ... control, the probable maximum precipitation of a 6-hour precipitation event, or greater event as specified.... Runoff from areas above the disposal facility or runoff from surface of the facility that may cause...-hour design precipitation event. (e) Impounding structures constructed of or impounding coal mine waste...

  7. Revegetation of coal mine soil with forest litter

    Energy Technology Data Exchange (ETDEWEB)

    Day, A.D.; Ludeke, K.L.; Thames, J.L.

    1986-11-01

    Forest litter, a good source of organic matter and seeds, was applied on undisturbed soil and on coal mine (spoils) in experiments conducted on the Black Mesa Coal Mine near Kayenta, Arizona over a 2-year period (1977-1978). Germination, seedling establishment, plant height and ground cover were evaluated for two seeding treatments (forest litter and no forest litter) and two soil moisture treatments (natural rainfall and natural rainfall plus irrigation). The forest litter was obtained at random from the Coconino National Forest, broadcast over the surface of the soil materials and incorporated into the surface 5 cm of each soil material. Germination, seedling establishment, plant height and ground cover on undisturbed soil and coal mine soil were higher when forest litter was applied than when it was not applied and when natural rainfall was supplemented with sprinkler irrigation than when rainfall was not supplemented with irrigation. Applications of forest litter and supplemental irrigation may ensure successful establishment of vegetation on areas disturbed by open-pit coal mining.

  8. Effect of timber supplies on the efficiency of coal mining

    Energy Technology Data Exchange (ETDEWEB)

    Kulish, S A; Ponikarov, V D

    1977-01-01

    An analysis is made of the system of supplying coal mining production associations with timber materials. The potential for greater efficiency in the use and processing of timber is indicated. The possibility of using methods of mathematical modelling and forecasting to improve the efficiency of supplying timber to coal associations is demonstrated. 1 table.

  9. Planning, layout and infrastructure of modern coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Haarmann, K R

    1978-02-01

    When designing layout and infrastructure of new coal mines, the principles of planning play a decisive role. Apart from exploration, ventilation, transport, dirt haulage and product haulage, material transport is very important. Illustrated by three examples, modern layout and infrastructure design is presented.

  10. The role of the state coal mining enterprise in Indonesia

    International Nuclear Information System (INIS)

    Mangunwidjaja, I.A.

    1991-01-01

    This paper reports that PT Tambang Batubara Bukit Asam is now becoming one of the 3 State Mining Enterprises in Indonesia which is dealing specifically with coal minings and their developments, while the other 2 are PT Tambang Timah for tin and PT Aneka Tambang for miscellaneous minerals. However, there are actually 3 other more State Enterprises under the umbrella of the Department of Mines and Energy, namely PERTAMINA which is dealing with oil and natural gas exploitation, PLN which is the State Electricity Corporation and the State Gas Corporation. The process of merging into one State Coal Mining Enterprise was only happening on October 30, 1990 by the issuance of the Government Regulation Number 56, 1991 whereby the then called Perum Tambang Batubara was merged into PT Tambang Batubara Bukit Asam, which was then operating only in Tanjung Enim, South Sumatra. The new scope of operation and management of the PT Tambang Batubara Bukit Asam is now including not only the management of coal mines at Tanjung Enim South Sumatra, but also the coal mines at Ombilin, West Sumatra and the supervision of all contract of works in coal which up to now amount to 11, mostly spread in East Kalimantan, South Kalimantan and one in West Sumatra. The amount of coal produced by PT Tambang Batubara Bukit Asam in 1990 was 4,854 million tons, while the coal production from all contract of works was 4,059 million tons for the same year

  11. 78 FR 27442 - Coal Mine Dust Sampling Devices; Correction

    Science.gov (United States)

    2013-05-10

    ... DEPARTMENT OF LABOR Mine Safety and Health Administration Coal Mine Dust Sampling Devices; Correction AGENCY: Mine Safety and Health Administration, Labor. ACTION: Notice; correction. SUMMARY: On April 30, 2013, Mine Safety and Health Administration (MSHA) published a notice in the Federal Register...

  12. The use of coal mining wastes for manufacturing paving materials; Los esteriles del carbon como materia prima para la fabricacion de materiales para pavimentacion

    Energy Technology Data Exchange (ETDEWEB)

    1999-09-01

    This project was aimed at proving the technical feasibility of the use of coal mining wastes in the manufacturing of paving materials; floor-tiles, flags, paving-stones, grit stones, etc.. With that aim, four types of coal mining wastes were selected out of an inventory and several tests were conducted and following the results, the most appropriate coal mining wastes, the acceptance limits and the quality control tests to be applied to the materials obtained from coal mining wastes as starting materials for the manufacturing of paving materials were established. Different laboratory test were conducted on the manufacturing of flags, floor-tiles and paving-stones. In addition, semi-industrial scale tests were carried out on the manufacturing of grit stones. Preliminary manufactory designs were elaborated for both material types. The study proved that coal mining wastes in a mixture with other raw materials can be used in the manufacturing of paving materials: floor-tiles, flags, paving-stones, grit stones. (Author)

  13. Fiscal 2000 information collection/analysis project on basic research for coal resource exploitation. Research on technology of low-concentration methane gas recovery from underground coal mine; 2000 nendo sekitan shigen kaihatsu kiso chosa joho shushu kaiseki jigyo. Konaikutsu tanko ni okeru teinodo methane kaishu gijutsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Technical trends were surveyed concerning the recovery and the use as fuel of low-concentration methane gas or the like contained in the air ventilated out of coal mines. Methane gas recovery technologies include high-temperature incinerators and catalytic incinerators designed to collect heat, method of conversion of methane to CO2 using microbes named methanotrophs, and adsorption methods using activated charcoal, zeolite, or the like. Among technologies that have reached a practical level in the utilization of mine methane gas, there are the temperature regenerative flow-reversal reactor (TFRR) and the catalytic flow-reversal reactor (CFRR) utilizing high-temperature oxidation reaction. TFRR has been reported effective by MEGTEC System after a 6-month operational test of a 3.0m{sup 3}/s plant at a British coal mine. Test and research are over with CFRR, which is now ready for a commercial scale verification test. Recovery by adsorption, though worth further research efforts, is economically away from commercialization at the present stage, and wants more studies of adsorbents, etc. (NEDO)

  14. Coal mining technologies possible for use in the Polish hard coal mining sector ensuring its sustainable development; Technologie eksploatacji wegla mozliwe do zastosowania w polskim gornictwie wegla kamiennego zapewniajace jego zrownowazony rozwoj

    Energy Technology Data Exchange (ETDEWEB)

    Dubinski, J. [Central Mining Institute, Katowice (Poland)

    2004-07-01

    The paper presents a prediction of the developments in hard coal mining technologies both in Poland and in the world. The longwall and the room-and-pillar systems will be realised. In Poland longwall equipment must be made more reliable and be better monitored, and more use made of roof bolting and means of controlling methane and rockbursts. Methods of underground gasification of coal seams need further development to realise the potential of this resource at reasonable production cost and with minimal environmental impact. 38 refs., 6 figs., 4 tabs.

  15. The impact of liberalisation of the electricity market on the hard coal mining sector in Poland

    Energy Technology Data Exchange (ETDEWEB)

    Kaminski, Jacek [Mineral and Energy Economy Research Institute of Polish Academy of Sciences, Energy and Environmental Policy Division, Wybickiego 7, 31-261 Krakow (Poland)

    2009-03-15

    The liberalisation of the electricity market changed the conditions of operation not only for the power industry, but also for related sectors. One of the particularly sensitive industries in Poland is coal mining, which is the result of coal-based structure of electricity generation. As it is more difficult, in the liberalised market, to burden consumers with all the costs, electricity producers are eager to transfer the risk of operation to the suppliers. That increases uncertainty about the future of the hard coal industry. The aim of this paper was to quantitatively estimate the impact that liberalisation of the electricity markets may have on the coal mining sector in Poland. First of all, the possible areas of that impact were identified. Then the model, which involved detailed relations in the impact areas identified, was developed and employed to evaluate the performance of the mining sector. The comparison of scenarios of a monopolistic electricity sector with a liberalised one enabled an estimation of the scale of the impact on the mining sector to be made. The results showed that liberalisation causes decreased coal consumption and decreased operating profits in coal companies. However, some savings in electricity costs are possible for coal producers. (author)

  16. The impact of liberalisation of the electricity market on the hard coal mining sector in Poland

    Energy Technology Data Exchange (ETDEWEB)

    Jacek Kaminski [Mineral and Energy Economy Research Institute of Polish Academy of Sciences, Krakow (Poland). Energy and Environmental Policy Division

    2009-03-15

    The liberalisation of the electricity market changed the conditions of operation not only for the power industry but also for related sectors. One of the particularly sensitive industries in Poland is coal mining, which is the result of coal-based structure of electricity generation. As it is more difficult, in the liberalised market, to burden consumers with all the costs, electricity producers are eager to transfer the risk of operation to the suppliers. That increases uncertainty about the future of the hard coal industry. The aim of this paper was to quantitatively estimate the impact that liberalisation of the electricity markets may have on the coal mining sector in Poland. First of all, the possible areas of that impact were identified. Then the model, which involved detailed relations in the impact areas identified, was developed and employed to evaluate the performance of the mining sector. The comparison of scenarios of a monopolistic electricity sector with a liberalised one enabled an estimation of the scale of the impact on the mining sector to be made. The results showed that liberalisation causes decreased coal consumption and decreased operating profits in coal companies. However, some savings in electricity costs are possible for coal producers. 42 refs., 20 figs., 9 tabs., 1 app.

  17. The impact of liberalisation of the electricity market on the hard coal mining sector in Poland

    International Nuclear Information System (INIS)

    Kaminski, Jacek

    2009-01-01

    The liberalisation of the electricity market changed the conditions of operation not only for the power industry, but also for related sectors. One of the particularly sensitive industries in Poland is coal mining, which is the result of coal-based structure of electricity generation. As it is more difficult, in the liberalised market, to burden consumers with all the costs, electricity producers are eager to transfer the risk of operation to the suppliers. That increases uncertainty about the future of the hard coal industry. The aim of this paper was to quantitatively estimate the impact that liberalisation of the electricity markets may have on the coal mining sector in Poland. First of all, the possible areas of that impact were identified. Then the model, which involved detailed relations in the impact areas identified, was developed and employed to evaluate the performance of the mining sector. The comparison of scenarios of a monopolistic electricity sector with a liberalised one enabled an estimation of the scale of the impact on the mining sector to be made. The results showed that liberalisation causes decreased coal consumption and decreased operating profits in coal companies. However, some savings in electricity costs are possible for coal producers. (author)

  18. Environmental policy in brown coal mining in accordance with the precautionary measures principle and polluter pays principle

    International Nuclear Information System (INIS)

    Hamann, R.; Wacker, H.

    1993-01-01

    The precautionary measures principle and the polluter pays principle in brown coal mining are discussed. Ground water subsidence and landscape destruction are local or regional problems and thus easily detectable. If damage cannot be avoided, its authors are known and will pay. In spite of all this, the German brown coal industry is well able to compete on the world market with others who don't care about the environmental damage they may cause. (orig./HS)) [de

  19. Fifty years ago, the black coal mine Barsinghausen was shut down; Vor 50 Jahren wurde das Steinkohlenbergwerk Barsinghausen stillgelegt

    Energy Technology Data Exchange (ETDEWEB)

    Boden, Konrad

    2008-09-09

    In the year 1957, the black coal mine Barsinghausen of the former Preussag AG was shut down. Under this aspect, the author of the contribution under consideration recalls this event. Substantial aspects of this contribution are: (a) The mine in the year 1955; (b) How did it come to the shutdown? (c) Reactions in the publicity; (d) Settlement of alternative industry; (e) Works council; (f) Social plan; (g) Where is the staff?.

  20. Interdependence between natural conditions and mining in causes of landslides in the vicinity of a coal mine

    Energy Technology Data Exchange (ETDEWEB)

    Krajewski, R; Rybicki, S; Palki, J

    1983-01-01

    This paper discusses effects of underground black coal mining in the Rybnik coal region in Upper Silesia on landslides. Geologic structures of a mine situated in the southern section of the Chwalowice trough are analyzed. Several landslides and events which could have influenced them are discussed. The following data on landslides are given: date, season of the year, dimensions and range of a landslide, angle of slope inclination, angle of slope inclination after a landslide, water conditions, type of soil and its mechanical properties. Investigation results are given in 7 tables. Analyses show that only some landslides were caused by underground coal mining and the remaining ones were caused by natural factors. There is a close correlation between landslide number and atmospheric precipitation (between landslides and seasons characterized by a level of atmospheric precipitation far exceeding the average). Landslides are more frequent in the case of slopes with angle of inclination exceeding 30 degrees and under conditions of soils characterized by low stability (cohesion). Underground mining is only a supplementary factor which reduces soil stability and increases water infiltration. (8 refs.)

  1. Environmental assessment and nano-mineralogical characterization of coal, overburden and sediment from Indian coal mining acid drainage

    Directory of Open Access Journals (Sweden)

    Madhulika Dutta

    2017-11-01

    Full Text Available The deterioration of environmental conditions is the major contributory factor to poor health and quality of life that hinders sustainable development in any region. Coal mining is one of the major industries that contribute to the economy of a country but it also impacts the environment. The chemical parameters of the coal, overburden, soil and sediments along with the coal mine drainage (CMD were investigated in order to understand the overall environmental impact from high sulphur coal mining at northeastern coalfield (India. It was found that the total sulphur content of the coal is noticeably high compared to the overburden (OB and soil. The volatile matter of the coal is sufficiently high against the high ash content of the soil and overburden. The water samples have a High Electrical Conductivity (EC and high Total Dissolve Solid (TDS. Lower values of pH, indicate the dissolution of minerals present in the coal as well as other minerals in the mine rejects/overburden. The chemical and nano-mineralogical composition of coal, soil and overburden samples was studied using a High Resolution-Transmission Electron Microscopy (HR-TEM, Energy Dispersive Spectroscopy (EDS, Selected-Area Diffraction (SAED, Field Emission-Scanning Electron Microscopy (FE-SEM/EDS, X-ray diffraction (XRD, Fourier Transform Infrared Spectroscopy (FTIR, Raman and Ion-Chromatographic analysis, and Mössbauer spectroscopy. From different geochemical analysis it has been found that the mine water sample from Ledo colliery has the lowest pH value of 3.30, Tirap colliery samples have the highest electrical conductivity value of 5.40 ms cm−1. Both Ledo and Tirap coals have total sulphur contents within the range 3–3.50%. The coal mine water from Tirap colliery (TW-15B has high values of Mg2+ (450 ppm, and Br− (227.17 ppm. XRD analysis revealed the presence of minerals including quartz and hematite in the coals. Mineral analysis of coal mine overburden (OB indicates

  2. Environmental impact of coal mine methane emissions and responding strategies in China

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Y.P.; Wang, L.; Zhang, X.L. [China University of Mining & Technology, Xuzhou (China)

    2011-01-15

    The impact on global climate change from coal mine methane emissions in China has been drawing attention as coal production has powered its economic development. Data on coal mine methane emissions from the State Administration of Coal Mine Safety of China has been analyzed. It is estimated that the methane emission from coal mining in China reached 20 billions of cubic meters in 2008, most of which comes from state-owned coal mines with high-gas content. China releases six times as much of methane from coal mines as compared to the United States. However, Chinese methane emission from coal production accounts for only a very small proportion on the environmental impact when compared to emissions of carbon dioxide from fossil fuel consumption. The Chinese government has shown environmental awareness and resolution on the mitigation and utilization of coal mine methane emissions. Measures have been taken to implement the programs of mitigation and utilization of coal mine methane, and at the same time, to ensure mining safety. Nearly 7.2 billions of cubic meters of methane were drained from the coal mines, and 32% of it was utilized in 2008. The slow advancement of technologies for the drainage and utilization of low-concentration methane from ventilation air hinders the progress of mitigation of atmospheric methane and the utilization of coal mine methane emissions.

  3. Coal Mine Health and Safety Regulation 2006 under the Coal Mine Health and Safety Act 2002

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-12-22

    The aim of the Act is to secure the health, safety and welfare of people in connection with coal operations (which include all places of work where coal is mined and certain other places). The Regulation contains provisions about the following matters: (a) places of work to which the Act does not apply, (b) duties relating to health, welfare and safety at coal operations, including the following: (i) the nomination of the operator of a coal operation and the provision of health and safety information for incoming operators, (ii) the contents of health and safety management systems for coal operations, (iii) major hazards and the contents of major hazard management plans for coal operations, (iv) duties relating to contractors, (v) the contents of management structures and emergency management systems for coal operations, escape and rescue plans and fire fighting plans and high risk activities, (c) notifications, including (i) notification of incidents, (ii) inquiries, (iii) notification of other matters to the Chief Inspector), (d) aspects of safety at coal operations, including the following: (i) controlled materials, plants and practices, (ii) coal dust explosion prevention and suppression, (iii) ventilation at coal operations, (iv) escape from coal operations, (v) the operation of transport at coal operations, (vi) surveys and certified plans, (vii) employment at coal operations, (e) the licensing of certain activities, (f) competence standards, (g) the Coal Competence Board, (h) check inspectors, (i) exemptions from provisions of this Regulation, (j) the following miscellaneous matters concerning coal mine health and safety: (i) the keeping of records and reporting, (ii) penalties, the review of decisions by the Administrative Decisions Tribunal, fees and charges, consultation, information and other miscellaneous matters, (k) savings and transitional provisions.

  4. Digital coal mine integrated automation system based on Controlnet

    Energy Technology Data Exchange (ETDEWEB)

    Jin-yun Chen; Shen Zhang; Wei-ran Zuo [China University of Mining and Technology, Xuzhou (China). School of Chemical Engineering and Technology

    2007-06-15

    A three-layer model for digital communication in a mine is proposed. Two basic platforms are discussed: a uniform transmission network and a uniform data warehouse. An actual, ControlNet based, transmission network platform suitable for the Jining No.3 coal mine in China is presented. This network is an information superhighway intended to integrate all existing and new automation subsystems. Its standard interface can be used with future subsystems. The network, data structure and management decision-making all employ this uniform hardware and software. This effectively avoids the problems of system and information islands seen in traditional mine-automation systems. The construction of the network provides a stable foundation for digital communication in the Jining No.3 coal mine. 9 refs., 5 figs.

  5. Opencast coal mining in India: present status and future trends

    Energy Technology Data Exchange (ETDEWEB)

    Khare, B.P. [Kakatiya University, Warangal (India)

    2007-07-01

    This paper discussed the opencast coal mining in India, present status and future trends including technology trends. The opencast coal mines in the coming years will have to switch over more and more to semi continuous and continuous mining. Whatever be the system adopted it should be sustainable to meet the output levels commensurate with environmental protection, safety, health, conservation and economics. It could, therefore, be summed up that the search for new technologies should be based on: (1) use of continuous miners; (2) use of bucket wheel excavators, conveyors, and spreaders; (3) shovel-crusher and conveyor system; and (4) application of high angle conveyors, cross-pit conveyors, and OB bridges. 4 tabs.

  6. Trust and safety in the coal mining sector

    Energy Technology Data Exchange (ETDEWEB)

    Neil Gunningham; Darren Sinclair [Gunningham and Associates (Australia)

    2008-08-15

    This report examines the relationship between trust (and mistrust) and occupational health and safety (OHS) in the Australian coal mining sector. Previous research in Australian coal mining companies indicated that mistrust is deep-seated at a number of mines, and that these mines are usually the worst performers in terms of OHS. Mistrust also handicaps the ability of inspectors to worker together with mines sites to improve OHS outcomes. Given this, there is a compelling need to understand how mistrust comes about, and to identify practical steps that can be adopted by companies, mines sites and the inspectorate to foster the development of trust. The report builds on these earlier findings by investigating trust in a much more detailed and sophisticated fashion, drawing on an in-depth analysis at mines, across a number of coal mining companies, and in two state jurisdictions. Research revealed that a 'cluster of characteristics' are associated with the formation and maintenance of mistrust at mines with a lower OHS track-record. These findings, together with an analysis of the characteristics of mines with better OHS outcomes, enabled the report to outline a variety of ways in which mines may build trust within and between management and the workforce. It also considers the at times fractious relationship between trade unions and management, and flags some of the challenges confronting these two groups in working together to improve OHS performance in the coal mining sector. Finally, the report examines the rise and impact of mistrust on the operations of the New South Wales and Queensland inspectorates, and suggests ways in which a fairer and more just enforcement policy may help foster greater trust between inspectors and mines.

  7. Gamma radiation hazard to miners in bituminous coal mines

    International Nuclear Information System (INIS)

    Skubacz, K.

    1986-01-01

    Radiation hazard to miners working in 16 bituminous coal mines was determined by a thermoluminescence method. While the miners exposure to gamma radiation is higher than that of the general population, the yearly dose was never found to exceed 5 mSv in any investigated person. Factors contributing to the estimate of the exposure hazard and the need for individual dose monitoring in mines are discussed in more detail. 3 refs., 4 figs. (author)

  8. Application of stable isotopes to hydrogeology in coal mine

    International Nuclear Information System (INIS)

    Duan Qi; Duan Yucheng

    1988-01-01

    Stable isotopes including Oxygen-18 and Deuterium have been applied to investigation of hydrogeology in main coal mines. By determination of stable isotopic composition of hydrogen and oxygen together with water analysis, the following studies have been developed: Identification of the hydrogeochemical characteristics of the groundwater from varied aquifers; Analysis of the hydraulic relationship between varied aquifers; Interpretation of the probable recharge source of mine water. The research results mentioned above reveal that: 1. The groundwater from main aquifers at coal mines in north China is of meteoric origin, which is recharged from hilly area surrounding the coal mine. Its isotopic composition differs slightly from that of the local precipitation. 2. There is a mutual hydraulic relationship between the Ordovician and Quarternary aquifers, so the difference of isotopic composition is very small. 3. By way of the variation of isotopic composition of groundwater from coal-bearing strata, we can infer the hydraulic relationship extent between overlaid alluvial layer and underlaid Ordovician limestone. (author). 9 refs, 6 figs, 8 tabs

  9. Drainage from coal mines: Chemistry and environmental problems

    International Nuclear Information System (INIS)

    Wildeman, T.

    1991-01-01

    Much of the research on coal-mine drainage chemistry was conducted a decade ago, and now increased environmental awareness has brought about renewed interest in the findings. Consideration of the trace minerals and elements in coal points to the possible generation of acidic waters upon weathering, especially when pyrite is present. When pyrite weathers, it produces H + and Fe 3+ which catalyze the incongruent weathering of other carbonates and sulfides. In this weathering mechanism, catalysis by bacteria is important. Of the environmental problems in coal mine drainage, the mineral acidity of the water is the most serious. This is caused not only by the H + , but also by Mn 4+ , Fe 3+ , and Al 3+ that are found or generated within the drainage. Case studies in Kentucky, Pennsylvania, Illinois, and Colorado show that the abundance and form of pyrite in the deposit and in the overburden determines the level of acidity and the concentration of heavy metal pollutants in the drainage. Recent trends in environmental enforcement that emphasize integrated stream water standards and biotoxicity assays point to the possibility that the concentrations of heavy metals in coal mine drainages may cause environmental concern

  10. Phytoremediation of coal mine spoil dump through integrated biotechnological approach

    Energy Technology Data Exchange (ETDEWEB)

    Juwarkar, A.A.; Jambhulkar, H.P. [National Environmental Engineering Research Institute, Nagpur (India)

    2008-07-15

    Field experiment was conducted on mine spoil dump on an area of 10 ha, to restore the fertility and productivity of the coal mine spoil dump using integrated biotechnological approach. The approach involves use of effluent treatment plant sludge (ETP sludge), as an organic amendment, biofertilizers and mycorrihzal fungi along with suitable plant species. The results of the study indicated that amendment with effluent treatment plant sludge (ETP sludge), at 50 ton/ha improved the physico-chemical properties of coal mine spoil. Due to biofertilizer inoculation different microbial groups such as Rhizobium, Azotobacter and VAM spores, which were practically absent in mine spoil improved greatly. Inoculation of biofertilizer and application of ETP sludge helped in reducing the toxicity of heavy metals such as chromium, zinc, copper, iron, manganese lead, nickel and cadmium, which were significantly reduced to 41%, 43%, 37%, 37%, 34%, 39%, 37% and 40%, respectively, due to the increased organic matter content in the ETP sludge and its alkaline pH (8.10-8.28), at which the metals gets immobilized and translocation of metals is arrested. Thus, amendment and biofertilizer application provided better supportive material for anchorage and growth of the plant on coal mine spoil dump.

  11. Assessment of soil pollution through trace element contamination in a coal mine environment of Jharia

    International Nuclear Information System (INIS)

    Singh, Gurdeep; Shrivastava, B.K.

    1997-01-01

    Coal mining environment is associated with liberation of several trace elements. Soils in such regions particularly have been polluted with these trace elements from a wide range of sources. Trace elements such as lead, copper, iron, zinc, chromium, manganese, cobalt, nickel, cadmium, etc. have caused major human health problems in several parts of the world. Concern over such incidents has prompted numerous investigations into the metabolism and toxic effects of these elements. The trace element contamination of soils (e.g. roadside, overburden dump, residential area etc.) in a part of the Jharia coal field running through a large industrial zone was studied. Representative soil samples from several highly polluted spots of the mining areas were collected and analysed. Results of the investigation revealed that the soils are polluted with trace elements to an appreciable level. Pollution index for soil was developed on the basis of observed concentration levels of trace elements of the study area which may help in better understanding of pollution analysis in coal mining areas. (author)

  12. Development of brown coal mining in the Federal Republic of Germany

    Energy Technology Data Exchange (ETDEWEB)

    Tilmann, W

    1985-01-01

    The significance of brown coal mining in the Federal Republic of Germany for the development of opencast technology and the power industry is discussed with emphasis on mining in the Rhineland Area. In 1984, 126.7 mt of brown coal were produced in the Federal Republic of Germany. In the development of high-performance equipment it is essential that the efficiency of the bucket-wheel excavator is increased. Trains and conveyors are mainly used for mine transport in the Federal Republic of Germany. A high moral commitment is linked to land claims, recultivation and environmental issues on the part of brown coal mining. In 1984 the percentage share of brown coal supplied to the public power stations was 83.6%, corresponding to 105.9 mt. The installed capacity of all brown coal power stations amounted to 12,764 MW at the end of 1984, providing around one quarter of overall public power output. Charge coal for coal refining has become more important and the production of brown coal dust and brown coal coke has also increased. The share of brown coal in domestic primary energy production is currently around 24% of 151 mt hard-coal units or around 10% of 376.5 mt hard-coal units in terms of energy consumption. 12 references.

  13. Assessment of radiological environment around coal mining area of Dhanbad, Jharkhand

    International Nuclear Information System (INIS)

    Patnaik, R.L.; Thakur, V.K.; Jha, V.N.; Sethy, N.K.; Srivastava, V.S.; Kumar, Rajesh; Tripathi, R.M.; Puranik, V.D.

    2012-01-01

    Naturally occurring radionuclides present in the earth crust is a significant source of human exposure. Variation in natural background radiation is expected in different geological formations. Anthropogenic activities in geological formation of elevated radionuclide level may enhance the area background. In areas of coal mining industries investigation of radiological environment is required as the residues contains significant amount of uranium and thorium series radionuclides (Van Hook, 1 979, Balogun, 2003). Radon and its short-lived progeny present in the environment contributes maximum natural background radiation dose due to inhalation. Apart from this radionuclide content in key environmental matrices may also contribute to inhalation and ingestion exposure for members of public. Present investigation was carried out in coal mining areas of Dhanbad, Jharkhand to assess the existing radiological status. A detailed investigation is required to evaluate the environmental impact of coal handling activities in the area. The contribution of 222 Rn progeny towards outdoor inhalation dose compares with global average reported by UNSCEAR (2006)

  14. A retrospective mortality study of workers exposed to radon in a Brazilian coal mine

    International Nuclear Information System (INIS)

    Veiga, Lene Holanda Sadler

    2004-08-01

    High levels of radon concentration were found in the underground workplace of an underground coal mine in Parana state, which has been in activity since 1942. Many of these workers were exposed for a long period of time to a work atmosphere with high radon, and radon decay products concentration. Taking this into account, it was decided to carry on a historical cohort, study with the workers' of this mining universe (underground and surface) in. order to evaluate the possible health effects related to this exposure, by means of a retrospective study of mortality. Through multiple strategies, it was possible to trace the vital status of 90% of the cohort. The causes of the deaths were identified by active search, of Death Declarations in the Health Office of Parana state and also in and other states. The success rate of cause of death identification was 100%. The final, cohort included 1946 underground workers and 910 surface workers. Standard mortality ratio (SMR) analysis showed lower mortality from all causes for both underground (SMR-88, 95%CI=78-98) and surface workers (SMR=96, 95%CI=81- 113). A highly significant SMR was observed for pneumonia cause of death among surface ((SMR=284, 95%CI=118-684) and underground miners (SMR-254, 95%CI=140-459), while a highly significant lung cancer mortality risk was observed only for underground miners (SMR=177, 95%CI=105-299) with a significant trend in relation to years of underground work (duration of exposure). Taking into account that mortality from smoking-related cancers other than lung cancer is not elevated in underground workers and diesel equipment were not used at this mine, the results suggest that the exposure to radon daughters may have been responsible for the lung cancer excess among underground workers. This work consists of the first historical Brazilian cohort involving miners exposed to radon and one of the few historical cohorts built in Brazil. It should be considered the fact that many workers of

  15. Annotated bibliography on selected areas of coal mining research and development. Report prepared for the Committee on Science and Technology, US House of Representatives, Ninety-Sixth Congress, First Session by the Congressional Research Service, Library of Congress

    Energy Technology Data Exchange (ETDEWEB)

    1979-01-01

    The Congressional Research Service has completed an annotated bibliography on coal mining research and development. Although the completion of the study was delayed in order to permit CRS analysts to search the libraries of Bituminous Coal, Research Inc., and the Bureau of Mines in the Pittsburgh area, current re-emphasis on the use of coal as an energy source indicates a sustained relevance. The bibliography presents key references to coal-mining R and D under six subject headings keyed to issues of central concern in coal production: (1) mine health and safety, (2) methane recovery, (3) 1-hour rescuer, (4) use of diesels underground, (5) coal preparation, and (6) manpower development in coal mining.

  16. FY 1998 annual report on the survey on overseas geological structures. Project for exchanging engineers (coal mining technology area) (Vietnam); 1998 nendo kaigai chishitsu kozo nado chosaa. Gijutsusha koryu jigyo (tanko gijutsu bun'ya) (Vietnam)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The project for exchanging engineers has been implemented, in order to improve production and managemental techniques of coal mining engineers in the Asia-Pacific region, promote smooth and efficient projects for surveying overseas geological structures, and facilitate stable supply of overseas coal to Japan. The FY 1998 project was concentrated on Vietnam, to which Japanese coal mining engineers were sent, and from which production management engineers were invited to Japan as trainees. The Japanese engineers sent to Vietnam educated the underground coal mining techniques. The Vietnamese management engineers invited were trained for, e.g., production management techniques (e.g., those for workplaces and organizations) in the Japanese mines, administrative management techniques, and techniques to improve safety and productivity in the mines. Coal Energy Center and Taiheiyo Mining's Kushiro Mine provided training facilities. (NEDO)

  17. FY 2000 international exchange project on exchanges of engineers - Coal mine technology field. Overseas workshop (Indonesia); 2000 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Kaigai workshop (Indonesia)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of making effective technology exchanges and surveying levels of technology in Indonesia and the needs and possibilities of technology transfer from Japan, workshop was held in Jakarta city on March 1, 2001. Subjects were the following seven: subjects on coal resource and technical strategy in the 21st century, challenge in coal development in Indonesia, geological structure survey at Tanjung Enim coal mine, waste water treatment in Indonesia, outlook for underground mining coal mines, joint research on the centralized monitoring system, and introduction of the optimum high wall coal mining system into open pit mining coal mines in Indonesia. The coal production amount in Indonesia was 75 million tons, and the domestic demand was 22 million tons. Japan imported 14 million tons from Indonesia. In coal mines in Indonesia, most of the coal preparation plants have no waste water treatment facilities. Considering that waste water treatment facilities are necessary for the plants in future, the joint research was made on the simple coal preparation waste water treatment system. (NEDO)

  18. Application of remote-sensing techniques to hydrologic studies in selected coal-mine areas of southeastern Kansas

    Science.gov (United States)

    Kenny, J.F.; McCauley, J.R.

    1983-01-01

    Disturbances resulting from intensive coal mining in the Cherry Creek basin of southeastern Kansas were investigated using color and color-infrared aerial photography in conjunction with water-quality data from simultaneously acquired samples. Imagery was used to identify the type and extent of vegetative cover on strip-mined lands and the extent and success of reclamation practices. Drainage patterns, point sources of acid mine drainage, and recharge areas for underground mines were located for onsite inspection. Comparison of these interpretations with water-quality data illustrated differences between the eastern and western parts of the Cherry Creek basin. Contamination in the eastern part is due largely to circulation of water from unreclaimed strip mines and collapse features through the network of underground mines and subsequent discharge of acidic drainage through seeps. Contamination in the western part is primarily caused by runoff and seepage from strip-mined lands in which surfaces have frequently been graded and limed but are generally devoid of mature stands of soil-anchoring vegetation. The successful use of aerial photography in the study of Cherry Creek basin indicates the potential of using remote-sensing techniques in studies of other coal-mined regions. (USGS)

  19. Study on Load-displacement Test of Rubber Pads of Coal Mine Roadway Constructed by Shield

    Science.gov (United States)

    Yang, Yue; Chen, Xiaoguo; Yang, Liyun

    2017-12-01

    Shield method construction of coal mine roadway is the future trend of the development of deep coal mining. The main shaft supporting is the segment. There is rubber pads between segment and segment. The performance of compression deformation of rubber pad is essential for the overall stability of lining. Through load test, displacement of the rubber pad under load, the thrust force law of the rubber pad deformation, and provide a theoretical basis for the stability analysis of coal mine tunnel shield construction.

  20. Accuracy criteria recommended for the certification of gravimetric coal-mine-dust samplers

    International Nuclear Information System (INIS)

    Bowman, J.D.; Bartley, D.L.; Breuer, G.M.; Doemeny, L.J.; Murdock, D.J.

    1984-07-01

    Procedures for testing bias and precision of gravimetric coal-mine-dust sampling units are reviewed. Performance criteria for NIOSH certification of personal coal-mine dust samplers are considered. The NIOSH criterion is an accuracy of 25% at the 95% confidence interval. Size distributions of coal-mine-dust are discussed. Methods for determining size distributions are described. Sampling and sizing methods are considered. Cyclone parameter estimation is discussed. Bias computations for general sampling units are noted. Recommended procedures for evaluating bias and precision of gravimetric coal mine dust personal samplers are given. The authors conclude that when cyclones are operated at lower rates, the NIOSH accuracy criteria can be met

  1. UNDERGROUND

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1993-11-15

    Full text: Cossetted deep underground, sheltered from cosmic ray noise, has always been a favourite haunt of neutrino physicists. Already in the 1930s, significant limits were obtained by taking a geiger counter down in Holborn 'tube' station, one of the deepest in London's underground system. Since then, neutrino physicists have popped up in many unlikely places - gold mines, salt mines, and road tunnels deep under mountain chains. Two such locations - the 1MB (Irvine/ Michigan/Brookhaven) detector 600 metres below ground in an Ohio salt mine, and the Kamiokande apparatus 1000m underground 300 km west of Tokyo - picked up neutrinos on 23 February 1987 from the famous 1987A supernova. Purpose-built underground laboratories have made life easier, notably the Italian Gran Sasso Laboratory near Rome, 1.4 kilometres below the surface, and the Russian Baksan Neutrino Observatory under Mount Andyrchi in the Caucasus range. Gran Sasso houses ICARUS (April, page 15), Gallex, Borexino, Macro and the LVD Large Volume Detector, while Baksan is the home of the SAGE gallium-based solar neutrino experiment. Elsewhere, important ongoing underground neutrino experiments include Soudan II in the US (April, page 16), the Canadian Sudbury Neutrino Observatory with its heavy water target (January 1990, page 23), and Superkamiokande in Japan (May 1991, page 8)

  2. UNDERGROUND

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    Full text: Cossetted deep underground, sheltered from cosmic ray noise, has always been a favourite haunt of neutrino physicists. Already in the 1930s, significant limits were obtained by taking a geiger counter down in Holborn 'tube' station, one of the deepest in London's underground system. Since then, neutrino physicists have popped up in many unlikely places - gold mines, salt mines, and road tunnels deep under mountain chains. Two such locations - the 1MB (Irvine/ Michigan/Brookhaven) detector 600 metres below ground in an Ohio salt mine, and the Kamiokande apparatus 1000m underground 300 km west of Tokyo - picked up neutrinos on 23 February 1987 from the famous 1987A supernova. Purpose-built underground laboratories have made life easier, notably the Italian Gran Sasso Laboratory near Rome, 1.4 kilometres below the surface, and the Russian Baksan Neutrino Observatory under Mount Andyrchi in the Caucasus range. Gran Sasso houses ICARUS (April, page 15), Gallex, Borexino, Macro and the LVD Large Volume Detector, while Baksan is the home of the SAGE gallium-based solar neutrino experiment. Elsewhere, important ongoing underground neutrino experiments include Soudan II in the US (April, page 16), the Canadian Sudbury Neutrino Observatory with its heavy water target (January 1990, page 23), and Superkamiokande in Japan (May 1991, page 8)

  3. Production and planning organization at coal mines. Organizatsiya proizvodstva i planirovanie na ugol'nykh shakhtakh

    Energy Technology Data Exchange (ETDEWEB)

    Rybnikov, S E; Voloshin, A P

    1981-01-01

    A discussion is made of problems concerning the organization of production, labor, and planning at enterprises of the coal industry. Theoretical and methodological principles are given for production organization, standardization and renumeration of wages, production planning and the use of available capacity. Computations are given for optimal numbers of workers, the essential growth in productivity, material expenditures for coal recovery, lowering production costs, and increasing the profitability of enterprise operations. Particular attention is given to the operation of mines of production and associations, organizational and practical problems concerned with the technical retooling of coal mines, and improving management and planning. The teaching aid is intended for students at coal technical institutes specializing in planning at enterprises of the coal industry. 14 references, 26 figures, 14 tables.

  4. Environmental management in hard coal mine group in the Upper Silesian Coal Basin, Poland

    International Nuclear Information System (INIS)

    Pozzi, M.; Weglarczyk, J.

    2000-01-01

    Mining activity and the other branches of heavy industry existing in the USCB for over 2 centuries have made large unfavourable changes of environment. Prevention of its further degradation needs the solution for the following main problems: utilisation of high saline mine drainage water (a problem unique in the world scale), treatment of solid wastes, land reclamation (mainly treatment of areas of ground subsiding). Market economy introduced 10 years ago and the necessity that all fields of life conform to the requirements of the European Union force the process of deep restructurisation of mining industry. One of the conditions for success of restructuring is the solution of ecological problems. The possibility of environmental management system implementation according to the ISO 14000 standard in the coal mine group condition was discussed. The chances and presumed results of these activities were presented in this paper. 6 refs

  5. Improving coal mining production performance through the application of total production management

    Energy Technology Data Exchange (ETDEWEB)

    Emery, J.C. [Devman Consulting Pty Ltd. (Australia)

    1998-12-31

    This paper describes the application of the Total Productive Management (TPM) technique as a performance improvement initiative for a coal mining operation. It discusses the objectives of TPM, with the driver for improved production performance being the Overall Equipment Effectiveness (OEE) of the equipment or process, and with the development of ownership as the behavioral approach to equipment management and continuous improvement through cross-functional and area-based teams. It illustrates the concept of equipment management as defects management. The scope for application of TPM to the coal mining industry is immense. The harshness of the operating environment can be a major generator of equipment defects, and a current paradigm in the industry accepts these defects as an unavoidable outcome defining maintenance costs in this environment. However recent benchmarking studies have highlighted that maintenance costs per operating hour in some mining operations are more than double the vendor`s estimate of best practice. The paper refers to these studies which also compare maintenance costs of fixed and mobile plant and equipment to best practice outcomes in comparable process industries. The ultimate goal of any operating strategy must be to translate results to the bottom line through adding revenue from increased volume and quality of operations output, better safety performance, and reducing costs of production through lower operating and maintenance costs. These lower costs result from removal of defects generators, improved maintenance planning, and identification and reduction of hidden operating costs resulting from poor equipment maintenance. Finally the paper outlines the minesite procedures required for successful implementation of TPM to sustain these desired results for all stakeholders. 3 refs., 6 figs.

  6. [Pollution Assessment and Spatial Distribution Characteristics of Heavy Metals in Soils of Coal Mining Area in Longkou City].

    Science.gov (United States)

    Liu, Shuo; Wu, Quan-yuan; Cao, Xue-jiang; Wang, Ji-ning; Zhang, Long-long; Cai, Dong-quan; Zhou, Li-yuan; Liu, Na

    2016-01-15

    The present paper takes the coal mining area of Longkou City as the research area. Thirty-six topsoil (0-20 cm) samples were collected and the contents of 5 kinds of heavy metals were determined, including Cd, As, Ni, Ph, Cr. Geo-statistics analysis was used to analyze the spatial distribution of heavy metals. Principal component analysis (PCA) was used to explore the pollution sources of heavy metals and the degree of heavy metals pollution was evaluated by weighted average comprehensive pollution evaluation method. The results showed that enrichment phenomenon was significant for the 5 kinds of heavy metals. Taking secondary standard of National Environment Quality Standard for Soil as the background value, their exceed standard rates were 72.22%, 100%, 100%, 91.67%, 100%, respectively. Average contents of heavy metals in the soil samples were all over the national standard level two and were 1.53, 11.86, 2.40, 1.31, 4.09 times of the background value. In addition, the average contents were much higher than the background value of the topsoil in the eastern part of Shandong Province and were 9.85, 39.98, 8.85, 4.29, 12.71 times of the background value. According to the semivariogram model, we obtained the nugget-effects of 5 kinds of heavy metals and their values were in the order of As (0.644) > Cd (0.627) > Cr (0.538) > Ni (0.411) > Pb (0.294), all belonging to moderate spatial correlation. On the whole, the central part of the Sangyuan Coal Mine and its surrounding areas were the most seriously polluted, while the pollution of heavy metals in the east and west of the study area was relatively light. Principal component analysis suggested that the enrichment of Cd, As, Ni, Cr was due to irrigation of wastewater, the discharge of industry and enterprise, and the industrial activity. Automobile exhaust and coal combustion were the main pollution sources of Pb. The single-factor assessment of heavy metals pollution showed that the degree of different heavy metals

  7. 20 CFR 726.1 - Statutory insurance requirements for coal mine operators.

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Statutory insurance requirements for coal mine operators. 726.1 Section 726.1 Employees' Benefits EMPLOYMENT STANDARDS ADMINISTRATION, DEPARTMENT OF LABOR FEDERAL COAL MINE HEALTH AND SAFETY ACT OF 1969, AS AMENDED BLACK LUNG BENEFITS...

  8. 20 CFR 726.203 - Federal Coal Mine Health and Safety Act endorsement.

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Federal Coal Mine Health and Safety Act endorsement. 726.203 Section 726.203 Employees' Benefits EMPLOYMENT STANDARDS ADMINISTRATION, DEPARTMENT OF LABOR FEDERAL COAL MINE HEALTH AND SAFETY ACT OF 1969, AS AMENDED BLACK LUNG BENEFITS; REQUIREMENTS FOR...

  9. Assessing the Impact of Removing Select Materials from Coal Mine Overburden, Central Appalachia Region, USA

    Science.gov (United States)

    The exposure of readily soluble components of overburden materials from surface coal mining to air and water results in mineral oxidation and carbonate mineral dissolution, thus increasing coal mine water conductivity. A conductivity benchmark of 300 µS/cm for mine water dischar...

  10. 26 CFR 1.187-1 - Amortization of certain coal mine safety equipment.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 3 2010-04-01 2010-04-01 false Amortization of certain coal mine safety... (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Itemized Deductions for Individuals and Corporations (continued) § 1.187-1 Amortization of certain coal mine safety equipment. (a) Allowance of deduction—(1) In...

  11. Coal mining situation in the Federal Republic of Germany. 1st half of 2015

    International Nuclear Information System (INIS)

    2015-01-01

    The report on coal mining in Germany contains statistical data on the following issues: (a) Hard coal mining: part 1: production, resources, performance, employees; part 2: marketing and foreign commerce. (b) brown coal: part 1: production, resources, performance, employees; part II: marketing in domestic and foreign commerce.

  12. Coal mining situation in the Federal Republic of Germany. January to September 2017

    International Nuclear Information System (INIS)

    2017-01-01

    This publication presents statistical data on hard coal mining (production, stocks, performance per miner and shift, headcount, sales, foreign sales, imports) as well as brown coal mining (production, refining, headcount, domestic sales, imports) in Germany during the period from January through September 2017.

  13. 30 CFR 74.5 - Tests of coal mine dust personal sampler units.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tests of coal mine dust personal sampler units... Personal Sampler Unit § 74.5 Tests of coal mine dust personal sampler units. (a) The National Institute for... tests and evaluations to determine whether the pump unit of a CMDPSU that is submitted for approval...

  14. Mathematical model for water quality impact assessment and its computer application in coal mine water

    International Nuclear Information System (INIS)

    Sundararajan, M.; Chakraborty, M.K.; Gupta, J.P.; Saxena, N.C.; Dhar, B.B.

    1994-01-01

    This paper presents a mathematical model to assess the Water Quality Impact in coal mine or in river system by accurate and rational method. Algorithm, flowchart and computer programme have been developed upon this model to assess the quality of coal mine water. 3 refs., 2 figs., 2 tabs

  15. 30 CFR 942.761 - Areas designated unsuitable for surface coal mining by act of Congress.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by act of Congress. 942.761 Section 942.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

  16. 30 CFR 903.761 - Areas designated unsuitable for surface coal mining by act of Congress.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by act of Congress. 903.761 Section 903.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, applies to surface coal mining...

  17. 30 CFR 933.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by Act of Congress. 933.761 Section 933.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated Unsuitable for Coal Mining by Act of Congress, with...

  18. 30 CFR 910.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by Act of Congress. 910.761 Section 910.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

  19. 30 CFR 937.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

    Science.gov (United States)

    2010-07-01

    ... mining by Act of Congress. 937.761 Section 937.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... WITHIN EACH STATE OREGON § 937.761 Areas designated unsuitable for surface coal mining by Act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining and...

  20. 30 CFR 921.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by Act of Congress. 921.761 Section 921.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

  1. 30 CFR 912.761 - Areas designated unsuitable for surface coal mining by act of Congress.

    Science.gov (United States)

    2010-07-01

    ... mining by act of Congress. 912.761 Section 912.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... WITHIN EACH STATE IDAHO § 912.761 Areas designated unsuitable for surface coal mining by act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining and...

  2. 30 CFR 947.761 - Areas designated unsuitable for surface coal mining by act of Congress.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by act of Congress. 947.761 Section 947.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

  3. 30 CFR 939.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by Act of Congress. 939.761 Section 939.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

  4. 30 CFR 941.761 - Areas designated unsuitable for surface coal mining by act of Congress.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by act of Congress. 941.761 Section 941.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

  5. 30 CFR 922.761 - Areas designated unsuitable for surface coal mining by act of Congress.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by act of Congress. 922.761 Section 922.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

  6. 30 CFR 905.761 - Areas designated unsuitable for surface coal mining by act of Congress.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by act of Congress. 905.761 Section 905.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

  7. Conversion of coal mining regions of France. La reconversion de la mineria del carbon en Francia

    Energy Technology Data Exchange (ETDEWEB)

    Torres, A.

    1990-08-01

    This programme of drastic reduction in coal mining in France has been made possible by the Economic Conversion Plan for the Coalfields. The Plan takes account of all areas of work affected by the reduction in coal mining and will assist in maintaining or even increase economic activity in the areas involved.

  8. 78 FR 25308 - Proposed Collection; Comment Request; Coal Mine Dust Sampling Devices

    Science.gov (United States)

    2013-04-30

    ...; Coal Mine Dust Sampling Devices AGENCY: Mine Safety and Health Administration, Labor. ACTION: 60-Day... mines. CPDMs must be designed and constructed for coal miners to wear and operate without impeding their... related to Coal Mine Dust Sampling Devices. MSHA is particularly interested in comments that: Evaluate...

  9. Electrical - light current remote monitoring, control and automation. [Coal mine, United Kingdom

    Energy Technology Data Exchange (ETDEWEB)

    Collingwood, C H

    1981-06-01

    A brief discussion is given of the application of control monitoring and automation techniques to coal mining in the United Kingdom, especially of the use of microprocessors, for the purpose of enhancing safety and productivity. Lighting systems for the coal mine is similarly discussed.

  10. 75 FR 63864 - Division of Coal Mine Workers' Compensation; Proposed Extension of Existing Collection; Comment...

    Science.gov (United States)

    2010-10-18

    ... DEPARTMENT OF LABOR Office of Workers' Compensation Programs Division of Coal Mine Workers... comments concerning the proposed collection: Comparability of Current Work to Coal Mine Employment (CM-913... Benefits Act of 1977, as amended, 30 U.S.C. 901 et seq., provides for the payment of benefits to coal...

  11. 78 FR 72717 - Division of Coal Mine Workers' Compensation; Proposed Collection; Comment Request

    Science.gov (United States)

    2013-12-03

    ... DEPARTMENT OF LABOR Office of Workers' Compensation Programs Division of Coal Mine Workers... proposed collection: Comparability of Current Work to Coal Mine Employment (CM-913). A copy of the proposed...., provides for the payment of benefits to coal miners who are totally disabled by black lung disease arising...

  12. Barrier capacity of weathered coal mining wastes with respect to heavy metal and organic contaminants

    International Nuclear Information System (INIS)

    Twardowska, I.; Jarosinska, B.

    1992-01-01

    Some types of weathered, buffered coal mining wastes (CMW), being essentially heterogenous and complex mineralogical system of developed surface area, under certain conditions could be widely applicable for binding a variety of contaminants both inorganic in cationic or anionic form, and organic compounds. The experiments reported earlier, showed excellent Cr(VI)-binding capacity of CMW. In this paper, experiments on simultaneous removal of heavy metals Cr t , Cu 2+ , Zn 2+ and Cd 2+ from highly (pH 2.5) and mildly acidic solutions (pH 4.0), as well as of organic compounds and color reduction in leachate from solid industrial waste dump (foundry wastes) will be presented

  13. Experimental Investigation of Flow Resistance in a Coal Mine Ventilation Air Methane Preheated Catalytic Oxidation Reactor

    Directory of Open Access Journals (Sweden)

    Bin Zheng

    2015-01-01

    Full Text Available This paper reports the results of experimental investigation of flow resistance in a coal mine ventilation air methane preheated catalytic oxidation reactor. The experimental system was installed at the Energy Research Institute of Shandong University of Technology. The system has been used to investigate the effects of flow rate (200 Nm3/h to 1000 Nm3/h and catalytic oxidation bed average temperature (20°C to 560°C within the preheated catalytic oxidation reactor. The pressure drop and resistance proportion of catalytic oxidation bed, the heat exchanger preheating section, and the heat exchanger flue gas section were measured. In addition, based on a large number of experimental data, the empirical equations of flow resistance are obtained by the least square method. It can also be used in deriving much needed data for preheated catalytic oxidation designs when employed in industry.

  14. These lives will not be lost in vain: organizational learning from disaster in US coal mining

    Energy Technology Data Exchange (ETDEWEB)

    Madsen, P.M. [Brigham Young University, Provo, UT (United States). Marriott School Management

    2009-09-15

    The stated purpose of the investigations that invariably follow industrial, transportation, and mining disasters is to learn from those tragedies to prevent future tragedies. But does prior experience with disaster make organizations more capable of preventing future disasters? Do organizations learn from disasters experienced by other organizations? Do organizations learn differently from rare disasters than they do from common minor accidents? In its present state, the organizational safety literature is poorly equipped to answer these questions. The present work begins to address this gap by empirically examining how prior organizational experience with disaster affects the likelihood that organizations will experience future disasters. It approaches the issue in the context of fatal U.S. coal mining accidents from 1983 to 2006. The analysis demonstrates that organizations do learn to prevent future disasters through both direct and vicarious experience with disaster. It also indicates that the mechanisms through which organizations learn from disasters differ from those through which they learn from minor accidents.

  15. Study on intelligent prediction of broken rock zone thickness of coal mine roadways

    Energy Technology Data Exchange (ETDEWEB)

    Xu, G.; Jing, H. [China University of Mining and Technology, Xuzhou (China). School of Architecture and Civil Engineering

    2005-03-01

    Considering the problem of obtaining the thickness of broken rock zone, a booming intelligent prediction method with ANFIS (adaptive neuro-fuzzy inference system) was introduced into the thickness prediction. A stand-alone program with functions of creating and applying prediction systems was designed on the platform of MATLAB6.5. Then the program was used to predict the broken rock zone thickness of dips in the 12th coal mine, Pingdingshan Group Company of Coal Industry. The results show that the predicted values correlate well with the in-situ measured ones. Thereby the validity of the program is validated and it can provide a new approach to obtaining the broken zone thickness. 10 refs., 4 figs., 1 tab.

  16. Nexsys{trademark} real time risk management system and demonstration at Kushiro coal mine

    Energy Technology Data Exchange (ETDEWEB)

    Addinell, S.J.; Rowan, G.; Matsuyama, S. [CSIRO (Australia). Division of Exploration and Mining

    2005-03-01

    In March 2005, the CSIRO Nexsys{trademark} development team travelled to Kushiro Coal Mine (KCM) to install and evaluate the Nexsys{trademark} real time risk management system developed under joint collaboration with JCOAL and other industry partners. After successful installation and configuration the system was able to interface directly to the existing mine site MELSEC monitoring hardware and system database. Once fully commissioned, Nexsys{trademark} will provide mine operators with a real-time risk management system with the capability to initiate preemptive Trigger Action Response Plans (TARPS) should mine operating parameters change for the worse. A range of autonomous altering and alarming options are available, including the capability to email the nature and severity of the alarm to key personnel, on or off site. The system is also fully compatible with wireless network systems and can be accessed through WLAN devices such as Ethernet enabled PDAs. 2 refs., 3 figs.

  17. Environmental evaluation for sustainable development of coal mining in Qijiang, Western China

    Energy Technology Data Exchange (ETDEWEB)

    Si, Hu; Bi, Haipu [College of Resource and Environment Science, Chongqing University, Chongqing 400030 (China); Key Lab for the Exploitation of Southwestern Resource and the Environment Disaster Control Engineering, the Ministry of Education, Chongqing University, Chongqing 400030 (China); Li, Xiaohong; Yang, Chunhe [Key Lab for the Exploitation of Southwestern Resource and the Environment Disaster Control Engineering, the Ministry of Education, Chongqing University, Chongqing 400030 (China)

    2010-03-01

    Environmental degradation associated with mining activities may seriously threaten the health of local people and the sustainable development of coal mining, which may need to be addressed by improved environmental evaluation system. Based on analyzing environmental pollution from coal mining and the increasing need for raw coal, this paper establishes an environmental evaluation system, covering environmental situation, resource protection and economic benefit, for sustainable development in coal mining. This paper proposes methods for calculating the weight of each index and the environmental sustainable capability taking into account the method of Analytic Hierarchy Process (AHP). Finally, the index system is used to evaluate the environmental sustainability of coal mining in the Qijiang area, Western China, which has demonstrated the validity of the index system. It may also be useful as a tool to assess the environmental impact of mining areas, as well as a measure to promote sustainable development in coal mining. (author)

  18. Costs of abandoned coal mine reclamation and associated recreation benefits in Ohio.

    Science.gov (United States)

    Mishra, Shruti K; Hitzhusen, Frederick J; Sohngen, Brent L; Guldmann, Jean-Michel

    2012-06-15

    Two hundred years of coal mining in Ohio have degraded land and water resources, imposing social costs on its citizens. An interdisciplinary approach employing hydrology, geographic information systems, and a recreation visitation function model, is used to estimate the damages from upstream coal mining to lakes in Ohio. The estimated recreational damages to five of the coal-mining-impacted lakes, using dissolved sulfate as coal-mining-impact indicator, amount to $21 Million per year. Post-reclamation recreational benefits from reducing sulfate concentrations by 6.5% and 15% in the five impacted lakes were estimated to range from $1.89 to $4.92 Million per year, with a net present value ranging from $14.56 Million to $37.79 Million. A benefit costs analysis (BCA) of recreational benefits and coal mine reclamation costs provides some evidence for potential Pareto improvement by investing limited resources in reclamation projects. Copyright © 2012 Elsevier Ltd. All rights reserved.

  19. Study on coal mine macro, meso and micro safety management system

    Directory of Open Access Journals (Sweden)

    Longkang Wang

    2016-03-01

    Full Text Available In recent years, the coal mine safety production situation in our country improved year by year, but severe accidents still occurred; the accidents caused great economic loss to the national economy. According to statistical analysis, almost all of the coal mine accidents will expose the hidden danger in before, most of the accidents caused due to safety management not reaching the designated position and the hidden danger management does not take any decision in time. Based on the coal mine safety management holes in our country, the coal mine macro, meso and micro safety management system was established in this paper, which includes meaning and conception of the theories of the macro, meso and micro safety management, and also includes the matching hardware equipment, in order to achieve the hidden danger's closed-loop control and dynamic early warning in the process of coal mine production.

  20. Tannery and coal mining waste disposal on soil

    Energy Technology Data Exchange (ETDEWEB)

    Kray, C.H.; Tedesco, M.J.; Bissani, C.A.; Gianello, C.; da Silva, K.J. [CEFET BG, Goncalves (Brazil)

    2008-11-15

    Tannery residues and coal mine waste are heavily polluting sources in Brazil, mainly in the Southern States of Rio Grande do Sul and Santa Catarina. In order to study the effects of residues of chrome leather tanning (sludge and leather shavings) and coal waste on soybean and maize crops, a field experiment is in progress since 1996, at the Federal University of Rio Grande do Sul Experimental Station, county of Eldorado do Sul, Brazil. The residues were applied twice (growing seasons 1996/97 and 1999/00). The amounts of tannery residues were applied according to their neutralizing value, at rates of up to 86.8 t ha{sup -1}, supplying from 671 to 1.342 kg ha{sup -1} Cr(III); coal waste was applied at a total rate of 164 t ha{sup -1}. Crop yield and dry matter production were evaluated, as well as the nutrients (N, P, K, Ca, Mg, Cu and Zn) and Cr contents. Crop yields with tannery sludge application were similar to those obtained with N and lime supplied with mineral amendments. Plant Cr absorption did not increase significantly with the residue application. Tannery sludge can be used also to neutralize the high acidity developed in the soil by coal mine waste.

  1. Dust collection capacity of plants growing in coal mining areas

    International Nuclear Information System (INIS)

    Maiti, S.K.

    1993-01-01

    Plant can act as living filter of dust pollution in coal mining areas, where the amount of suspended particulate matter and dust fall rate is very high. Therefore, plant species growing in coal mining areas are classified as evergreen or deciduous with simple and compound leaf basis. The dust arresting capacity of each leaf is measured and expressed in g/m 2 . The study indicated that evergreen plants with simple, pilose surface, like - Alstonia, Ficus cunea, F. benghalensis and Mangifera indica are good dust catcher than evergreen compound leaves of Cassia siamea, Acacia arabica and Leucaena leucocephala. Deciduous with simple leaves, such as Zizyphus mauritiana, F. religiosa, Psidium guyava are also good dust collectors. Suitable plant species also help in quick reclamation of mined out areas; one practical difficulty for establishment of trees as green belts or reclamation purpose, has been incidence of cattle grazing. This study suggested a systematic way of selecting plant species on the basis of their efficiency in dust control and resistance to cattle grazing. (author). 16 refs., 3 tabs

  2. Reclamation of coal mine spoil dump through integrated biotechnological approach

    International Nuclear Information System (INIS)

    Juwarkar, A.S.; Thawale, P.R.; Mowade, S.; Shrivastava, S.; Deshbhratar, P.B.; Juwarkar, A.

    1994-01-01

    Laboratory and field studies were carried out to restore the fertility and productivity of coal mine spoil using primary clarifier sludge from paper mill effluent treatment plant and use of specialised culture of biofertilizers and mycorrhizal fungi. Plants namely Tectona grandis, Delbergia sissoo, Gmelina arporea, Emblica officinalis and Cassia seamea were grown. Sludge amendment enhanced the survival rate of plants to 80% compared to 20% in unamended spoil. Plants grown on unamended spoil showed stunted growth. Growth of plants increased by 188-484% when sludge was applied at the rate of 100 tonnes per hectare. At 100 tones per hectare sludge amendment, biofertilizer and mycorrhizae treatment there were 83.7 nodules in shishum as against only 4.6 nodules in case of spoil alone. Further root length was 276% and 281% more respectively in case of shishum and teak. Inoculation of plant saplings with respective biofertilizers and mycorrhizae further increased the plant growth by 144-198%. At Durgapur coal mine, 56,000 saplings of Tectona grandis, Gmelina arporea, Delbergia sissoo, Emblica officinalis, Azadirachta indica, Acacia ariculiformis, Prosopis etc were successfully planted on spoil dump using integrated biotechnological approach. 10 refs., 5 tabs

  3. Presentations from the 1992 Coal Mining Impoundment Informational Meeting

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-31

    On May 20 and 21, 1992, the MSHA Coal Mining Impoundment Informational Meeting was held at the National Mine Health and Safety Academy in Beckley, West Virginia. Fifteen presentations were given on key issues involved in the design and construction of dams associated with coal mining. The attendees were told that to improve the consistency among the plan reviewers, engineers from the Denver and Pittsburgh Technical Support Centers meet twice annually to discuss specific technical issues. It was soon discovered that the topics being discussed needed to be shared with anyone involved with coal waste dam design, construction, or inspection. The only way to accomplish that goal was through the issuance of Procedure Instruction Letters. The Letters present a consensus of engineering philosophy that could change over time. They do not present policy or carry the force of law. Currently, thirteen position papers have been disseminated and more will follow as the need arises. The individual paper were not even entered into the database.

  4. The environmental pollution perception of residents in coal mining areas: a case study in the Hancheng mine area, Shaanxi Province, China.

    Science.gov (United States)

    Shi, Xingmin; He, Fei

    2012-10-01

    The environmental behavior of the residents depends on their perception of environmental pollution. Hence, it is important for scientific and policy experts to research on the impact of the environmental pollution perception of local residents. Owing to the richness of natural resources, Hancheng coal mine areas are abound in heavy industries, and environmental pollution is serious and typical in this area, thus, the residents are anxious about their health. Using questionnaires, this paper surveys the perception of residents living in the coal mine area. The influential factors of environmental perception were analyzed by the Rank Sum Test. The results were: (1) the majority of the residents in the coal mine area are not satisfied with their living environment. The perception order of pollution severity is: air pollution > noise pollution > sanitation > water pollution. The residents think that pollution is mainly caused by coal processing. Hence, coal mining is not the main reason of the pollution in the coal mine area. (2) Age and length of residence have significant positive effects on perceptions of air, water, and noise pollutions; whereas education has a significant negative effect on perceptions of water and noise pollutions, as well as sanitation. This phenomenon can be explained by the various cultural groups having varied perceptions on the environmental pollution. In addition, proximity to mine has significant negative effect on perceptions of water and noise pollution. In conclusion, the paper discusses the effects of demographical and social factors on the perception of environmental pollution and gives suggestions on the planning and management of the environment.

  5. An Integrated Environment Monitoring System for Underground Coal Mines—Wireless Sensor Network Subsystem with Multi-Parameter Monitoring

    OpenAIRE

    Zhang, Yu; Yang, Wei; Han, Dongsheng; Kim, Young-Il

    2014-01-01

    Environment monitoring is important for the safety of underground coal mine production, and it is also an important application of Wireless Sensor Networks (WSNs). We put forward an integrated environment monitoring system for underground coal mine, which uses the existing Cable Monitoring System (CMS) as the main body and the WSN with multi-parameter monitoring as the supplementary technique. As CMS techniques are mature, this paper mainly focuses on the WSN and the interconnection between t...

  6. Management of dry flue gas desulfurization by-products in underground mines

    Energy Technology Data Exchange (ETDEWEB)

    Sevim, H.

    1997-06-01

    Disposal of coal combustion by-products (CCBs) in an environmentally sound manner is a major issue facing the coal and utility industries in the US today. Disposal into abandoned sections of underground coal mines may overcome many of the surface disposal problems along with added benefits such as mitigation of subsidence and acid mine drainage. However, many of the abandoned underground coal mines are located far from power plants, requiring long distance hauling of by-products which will significantly contribute to the cost of disposal. For underground disposal to be economically competitive, the transportation and handling cost must be minimized. This requires careful selection of the system and optimal design for efficient operation. The materials handling and system economics research addresses these issues. Transportation and handling technologies for CCBs were investigated from technical, environmental and economic points of view. Five technologies were found promising: (1) Pneumatic Trucks, (2) Pressure Differential Rail Cars, (3) Collapsible Intermodal Containers, (4) Cylindrical Intermodal Tanks, and (5) Coal Hopper Cars with Automatic Retractable Tarping. The first two technologies are currently being utilized in transporting by-products from power plants to disposal sites, whereas the next three are either in development or in conceptualization phases. In this research project, engineering design and cost models were developed for the first four technologies. The engineering design models are in the form of spreadsheets and serve the purpose of determining efficient operating schedules and sizing of system components.

  7. Considerations for modeling small-particulate impacts from surface coal-mining operations based on wind-tunnel simulations

    Energy Technology Data Exchange (ETDEWEB)

    Perry, S.G.; Petersen, W.B. [Air Resources Lab., Research Triangle Park, NC (United States); Thompson, R.S. [Atmospheric Research and Exposure Assessment Lab., Research Triangle Park, NC (United States)

    1994-12-31

    The Clean Air Act Amendments of 1990 provide for a reexamination of the current Environmental Protection Agency`s (USEPA) methods for modeling fugitive particulate (PM10) from open-pit, surface coal mines. The Industrial Source Complex Model (ISCST2) is specifically named as the method that needs further study. Title II, Part B, Section 234 of the Amendments states that {open_quotes}...the Administrator shall analyze the accuracy of such model and emission factors and make revisions as may be necessary to eliminate any significant over-predictions of air quality effect of fugitive particulate emissions from such sources.{close_quotes}

  8. Coal mining and water quality: Criciuma's case; Mineracao de carvao e a qualidade da agua: o caso de Criciuma

    Energy Technology Data Exchange (ETDEWEB)

    Fernandes, Lincoln

    1999-07-01

    The coal mining in the Santa Catarina Coal-Basin started in 1885 and since them it has been causing serious damage to the environment, specially the water resources, causing several problems like sedimentation and acidification of the rivers that supply the region, and compromising the agricultural-industry and fishery. The mining is also responsible for several professional diseases. The region was considered, in 1980, the '14th Critical Area' to the Pollution Control and Environmental Quality Conservation. Only in the beginning of the 80's, after the publication of the 917 Interministerial Resolution (July, 1982), the first official actions were taken, in order to minimize the environmental impact due to the coal mining industry. With that scenario, the region was chosen as one of the study areas of the 'National Center of Control of Mining Pollution', derived from an agreement between the Departamento Nacional de Producao Mineral - DNPM and the Japan International Cooperation Agency (JICA). The present study is part of the set of studies that have been realized in the region, with the aim of evaluating the environmental impact caused by the coal mining industry, and to suggest actions (to the miners) in order to minimize the environmental problems. This study presents a review of the occupation process of the Criciuma region, its connection to the coal industry, the progress of the mineral and environmental legislation, and the periodic monitoring of environmental parameters (physic-chemical analysis of the Mae Luzia and Sangao rivers, and the drainage from two coal mines) during the period of three years. This period began before the setting of environmental restrictions, going up to after the adoption of reclamation actions. The results allow to conclude that, during the period studied, there was no improvement in the river water characteristics, despite the adoption of reclamation actions. This behaviour may be due to the following factors: there are several

  9. Engineer exchanging project (coal mine technology field) in fiscal 1999. International information exchanging project (advance survey on Russia); 1999 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Jizen chosa (Roshia)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This advance survey on Russia has performed visiting surveys and information collection at coal related organizations inside Japan and in overseas countries on production technology levels, trends and technology exchange needs in overseas coal producing countries. The project is intended to serve for improvement in the contents of and smooth execution of the engineer exchange project in the 'coal mine technology field. It was carried out by expertise people as the site surveys and the engineer reception and exchange surveys. Because of the economic crisis that has hit Russia in 1998, unprofitable coal mines were closed one after another under the coal mine scrap and build policy under the initiative of the World Bank. This situation is giving serious impacts on coal mines in the Far East Russia and the coastal areas. However, the importance of coal as the primary energy source has not been changed at all in the Far East Russia. Thus, the areas have fallen into a situation that they must rely on a great amount of introduced and imported coals as a result of weakening in coal mines in the Far Eastern area on the other hand. This paper reports mainly the situation in which the coal industries in the coastal areas are placed, and the possibilities of technology exchange. (NEDO)

  10. An investigation on groundwater recovery rate within sub sea floor tunnels at closed coal mines

    International Nuclear Information System (INIS)

    Nakata, Eiji; Suenaga, Hiroshi; Oyama, Takahiro; Nomura, Tokisada; Ichihara, Yoshihisa

    2008-01-01

    The groundwater recovery rate investigated at the closed coal mines extended within sub sea floor tunnels. The Ikeshima and the Taiheiyo coal mine companies exploited the deep coal-bearing strata beneath the ocean. Ikeshima coal mine, excavated S.L. -650m to 6km offshore from Ikeshima island, was closed at November 2002, and Taiheiyo coal mine, excavated S.L. -720m to 9km offshore from Hokkaido, was stopped to excavate from the deep area at January 2003. After closing and stopping of development, we began the investigation of the groundwater recovery rate at both coal mines. The groundwater level of Ikeshima coal mine raised +405m per 1.8 years at the main shaft. The permeability coefficient estimated between 10 - 8 m /s and 10 -6 m/s to use the water recovery rate at the shaft. Otherwise, at Taiheiyo coal mine, we measured the air pressure in tubes used by 3.5km 2.5km, and 1.5km length 2mm diameters tubes to estimate the groundwater recovery level at the 3.2km offshore plug site. Groundwater didn't reach 4.7km (1.5+3.2km) area until November 2004. There were breakdown of shotcleate and rock mass from the roof of tunnel at 5.3km from offshore line. In this paper, we try to show the groundwater recovery rate of these sub sea floor collieries. (author)

  11. A Standard Characterization Methodology for Respirable Coal Mine Dust Using SEM-EDX

    Directory of Open Access Journals (Sweden)

    Rachel Sellaro

    2015-12-01

    Full Text Available A key consideration for responsible development of mineral and energy resources is the well-being of workers. Respirable dust in mining environments represents a serious concern for occupational health. In particular, coal miners can be exposed to a variety of dust characteristics depending on their work activities, and some exposures may pose risk for lung diseases like CWP and silicosis. As underscored by common regulatory frameworks, respirable dust exposures are generally characterized on the basis of total mass concentration, and also the silica mass fraction. However, relatively little emphasis has been placed on other dust characteristics that may be important in terms of identifying health risks. Comprehensive particle-level analysis to estimate chemistry, size, and shape distributions of particles is possible. This paper describes a standard methodology for characterization of respirable coal mine dust using scanning electron microscopy (SEM with energy dispersive X-ray (EDX. Preliminary verification of the method is shown based several dust samples collected from an underground mine in Central Appalachia.

  12. Coal mine subsidence: effects of mitigation on crop yields. [USA - Illinois

    Energy Technology Data Exchange (ETDEWEB)

    Darmody, R.G.; Hetzler, R.T.; Simmons, F.W. (Illinois Univ., Urbana, IL (USA). Dept. of Agronomy)

    1992-01-01

    Subsidence from longwall underground coal mining adversely impacts agricultural land by creating wet or ponded areas. While most subsided areas show little impact, some localized places, usually less than 1.5 ha in size, may experience total crop failure. Coal companies mitigate subsidence damaged cropland by installing drainage waterways or by adding fill material to raise the grade. The objective of this study was to test the effectiveness of mitigation in restoring corn and soybean yields to pre-mined levels. Fourteen sites in southern Illinois were selected for study. Corn ([ital Zea mays] L.) and soybean ([ital Glycine max] L.) yields from mitigated and nearby undisturbed areas were compared for four years. Results varied due to differing weather and site conditions. Mean corn yields overall, however were significantly ([alpha]0.05) lower on mitigated areas. There was no significant difference in overall mean soybean yields. Soil fertility levels were similar and did not account for yield differences. 14 refs., 1 fig., 7 tabs.

  13. Detection and control of fires and heatings in shallow, abandoned coal mines

    International Nuclear Information System (INIS)

    Sullivan, P.

    1991-01-01

    Heatings and fires in shallow, abandoned coal mines create an environmentally undesirable hazard in the Witbank area in South Africa, as well as locations in Europe and North America. A research program was set up in South Africa to detect and control the occurrence and extent of subsurface heatings and fires. Prior to any remedial action being taken to control or extinguish a heating or fire, it is essential to evaluate underground conditions in order to determine the most effective control method. Normally, such workings cannot physically be entered due to poor ground conditions and the presence of heat and toxic gases. Two novel detection methods have been developed by the Chamber of Mines Research Organization (COMRO) for the purpose of identifying the nature and extent of such heatings remotely, via surface boreholes. Temperature monitoring allows for the detection of heating intensity and location. To determine areas of uncontrolled air infiltration into the workings, tracer gas technology is used. In addition, a method for controlling a fire which has been successfully used in South Africa is described

  14. Inertisation of sealed coal mine panels using microbial organisms.

    CSIR Research Space (South Africa)

    Creedy, DP

    2000-02-01

    Full Text Available for methane removal 5 3.1 Techniques for applying the microbes 6 3.1.1 Coated roadway surfaces 6 3.1.2 Bio-filters 6 3.1.3 Passive bio-curtain filters 7 3.2 Process sustainability 8 3.3 Treatment configuration 8 3.3.1 Whole area treatment 8 3....3.2 Selected area treatment 8 3.3 Remote gas monitoring 8 4 A practical technology for South African coal mines 9 4.1 The preferred approach 9 4.2 Selection of micro-organisms for immobilisation 9 4.3 Development of the bio-curtain technology 9 4...

  15. Controlled Roof Collapse during Secondary Mining in Coal Mines

    Directory of Open Access Journals (Sweden)

    Ashleigh Hutchinson

    2012-01-01

    Full Text Available The problem considered is an investigation of the possible collapse of the roof between the pillar next to be mined in secondary coal mining and the first line of pillar remnants called snooks. The roof rock between the pillar, which is the working face, and the snook is modelled as an Euler-Bernoulli beam acted on at each end by a horizontal force and by its weight per unit length. The beam is clamped at the pillar and simply supported (hinged at the snook. The dimensionless differential equation for the beam and the boundary conditions depend on one dimensionless number . We consider the range of values of before the displacement and curvature first become singular at =1. The model predicts that for all practical purposes, the beam will break at the clamped end at the pillar. The failure of the beam for values of greater than 1 is investigated computationally.

  16. WORKPLACE AS AN OBJECT OF ACCOUNTING AT COAL MINES

    Directory of Open Access Journals (Sweden)

    Valeriy Nikolaevich Kuletskoy

    2014-10-01

    Full Text Available The paper presents an approach to evaluating the effectiveness of the workplace on the coal-mining enterprise based on an integrated consideration of three aspects: organizational, technological, social, labor, organizational and economic. In accordance with the definition given to aspects of the workplace: as part of the organization of production, the labor process, organizational and economic relations. Shows the structure of the workplace as an object of accounting, including: objective function, the subject of labor, means of labor, the subject of labor.Defined parameters describing the results obtained in the workplace, and the cost of its operation.The experience in the organization poobektnogo accounting efficiency in the use of jobs in the "Cut Tugnuisky."

  17. Landslide rehabilitation with geo synthetics in open coal mine Oslomej

    International Nuclear Information System (INIS)

    Dimitrievski, Ljupcho; Ilievska, Frosina; Ilievski, Darko

    2004-01-01

    In November 2002 stability is violated and landslides are registered in open coal mine Oslomej, Republic of Macedonia. Around the profile IV existing open irrigation channel was interrupted and landslide was extended to the regional way R421 Kicevo - Oslomej. The landslide was classified like big and dangerous, including danger for disruption of the regional road and pipeline Studencica - Oslomej for supplying of thermal power plant Oslomej with technical water. According to the proposed solution, main project design for landslide rehabilitation was prepared with using geo synthetics Stabilenka 200/45. In fill is local soil material which had been placed and compacted in layers, it had formed a composite construction. Stabilenka acts as a reinforcement due to its ability to absorb tensile forces. With the design solution two retaining walls of reinforced soil and complete drainage system of geo composite materials had been constructed This paper deals with details of the design and the construction. (Author)

  18. The determination of methane resources from liquidated coal mines

    Science.gov (United States)

    Trenczek, Stanisław

    2017-11-01

    The article refers to methane presented in hard coal seams, which may pose a serious risk to workers, as evidenced by examples of incidents, and may also be a high energy source. That second issue concerns the possibility of obtaining methane from liquidated coal mines. There is discussed the current methodology for determination of methane resources from hard coal deposits. Methods of assessing methane emissions from hard coal deposits are given, including the degree of rock mass fracture, which is affected and not affected by mining. Additional criteria for methane recovery from the methane deposit are discussed by one example (of many types) of methane power generation equipment in the context of the estimation of potential viable resources. Finally, the concept of “methane resource exploitation from coal mine” refers to the potential for exploitation of the resource and the acquisition of methane for business purposes.

  19. Causes of Coal Mine Accidents in the World and Turkey.

    Science.gov (United States)

    Küçük, Filiz Çağla Uyanusta; Ilgaz, Aslıhan

    2015-04-01

    Occupational accidents and occupational diseases are common in the mining sector in Turkey and throughout the world. The most common causes of accidents in coal mining are firedamp and dust explosions, landslips, mine fires, and technical failures related to transport and mechanization. An analysis of occupational accidents in the consideration of social and economic factors will let understand the real causes behind these accidents, which are said to happen inevitably due to technical deficiencies or failures. Irregular working conditions, based on profit maximization and cost minimization, are related to strategic operational preferences and public policies. Proving that accidents in mines, where occupational health and safety measures are not implemented and inspections are not done properly or at all, are caused by the fact that production is imposed to be carried out in the fastest, cheapest, and most profitable way will allow us to take steps to prevent further mine accidents.

  20. Case studies of slope stability radar used in coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Noon, D. [GroundProbe Pty Ltd., South Brisbane, Qld. (Australia)

    2005-07-01

    This paper presents case studies about how the Slope Stability Radar (SSR) system provided adequate warning to safeguard people and equipment prior to highwall and low wall failure at two Australian coal mines. At Drayton mine, the SSR was able to provide the mine with sufficient warning to move the shovel and trucks away from the highwall, while personnel safely watched 50,000 tonnes of bulk material coming down from the wall. At Mt Owen mine, the SSR alarm allowed the mine to evacuate equipment and personnel four hours prior to a 30,000,000 tonne low wall failure. These two case studies demonstrate how the SSR system was able to continuously monitor the stability of these critical slopes, enabling greater mine productivity whilst maintaining the highest quality of safety. 2 refs., 7 figs., 1 tab.

  1. Integrated circuit devices in control systems of coal mining complexes

    Energy Technology Data Exchange (ETDEWEB)

    1983-01-01

    Systems of automatic monitoring and control of coal mining complexes developed in the 1960's used electromagnetic relays, thyristors, and flip-flops on transistors of varying conductivity. The circuits' designers, devoted much attention to ensuring spark safety, lowering power consumption, and raising noise immunity and repairability of functional devices. The fast development of integrated circuitry led to the use of microelectronic components in most devices of mine automation. An analysis of specifications and experimental research into integrated circuits (IMS) shows that the series K 176 IMS components made by CMOS technology best meet mine conditions of operation. The use of IMS devices under mine conditions has demonstrated their high reliability. Further development of integrated circuitry involve using microprocessors and microcomputers. (SC)

  2. Causes of Coal Mine Accidents in the World and Turkey

    Science.gov (United States)

    Küçük, Filiz Çağla Uyanusta; Ilgaz, Aslıhan

    2015-01-01

    Occupational accidents and occupational diseases are common in the mining sector in Turkey and throughout the world. The most common causes of accidents in coal mining are firedamp and dust explosions, landslips, mine fires, and technical failures related to transport and mechanization. An analysis of occupational accidents in the consideration of social and economic factors will let understand the real causes behind these accidents, which are said to happen inevitably due to technical deficiencies or failures. Irregular working conditions, based on profit maximization and cost minimization, are related to strategic operational preferences and public policies. Proving that accidents in mines, where occupational health and safety measures are not implemented and inspections are not done properly or at all, are caused by the fact that production is imposed to be carried out in the fastest, cheapest, and most profitable way will allow us to take steps to prevent further mine accidents. PMID:29404108

  3. Selenium transformation in coal mine spoils: Its environmental impact assessment

    Energy Technology Data Exchange (ETDEWEB)

    Harness, J.; Atalay, A.; Koll, K.J.; Zhang, H.; Maggon, D.

    1991-12-31

    The objective of this program was to conduct an environmental impact assessment study for selenium from coal mine spoils. The use of in-situ lysimetry to predict selenium speciation, transformation, and mobility under natural conditions was evaluated. The scope of the study was to construct and test field-scale lysimeter and laboratory mini-column to assess mobility and speciation of selenium in coal mine overburden and soil systems; to conduct soil and groundwater sampling throughout the state of Oklahoma for an overall environmental impact assessment of selenium; and to conduct an in-depth literature review on the solubility, speciation, mobility, and toxicity of selenium from various sources. Groundwater and surface soil samples were also collected from each county in Oklahoma. Data collected from the lysimeter study indicated that selenium in the overburden of the abandoned mine site was mainly found in the selenite form. The amount of selenite found was too low and immobile to be of concern to the environment. The spoil had equilibrated long enough (over 50 years) that most of the soluble forms of selenium have already been lost. Examination of the overburden indicated the presence of pyrite crystals that precipitated over time. The laboratory mini-column study indicated that selenite is quite immobile and remained on the overburden material even after leaching with dilute acid. Data from groundwater samples indicated that based on the current permissible level for selenium in groundwater (0.01 mg Se/L), Oklahoma groundwater is widely contaminated with the element. However, according to the new regulation (0.05 mg Se/L), which is to be promulgated in 1992, only 9 of the 77 counties in the state exceed the limit.

  4. Prevention and forecasting of rock burst hazards in coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Lin-ming Dou; Cai-ping Lu; Zong-long Mu; Ming-shi Gao [China University of Mining & Technology, Xuzhou (China). State Key Laboratory for Coal Resource and Mine Safety

    2009-09-15

    Rock bursts signify extreme behavior in coal mine strata and severely threaten the safety of the lives of miners, as well as the effectiveness and productivity of miners. In our study, an elastic-plastic-brittle model for the deformation and failure of coal/rock was established through theoretical analyses, laboratory experiments and field testing, simulation and other means, which perfectly predict sudden and delayed rock bursts. Based on electromagnetic emission (EME), acoustic emission (AE) and microseismic (MS) effects in the process from deformation until impact rupture of coal-rock combination samples, a multi-parameter identification of premonitory technology was formed, largely depending on these three forms of emission. Thus a system of classification for forecasting rock bursts in space and time was established. We have presented the intensity weakening theory for rock bursts and a strong-soft-strong (3S) structural model for controlling the impact on rock surrounding roadways, with the objective of laying a theoretical foundation and establishing references for parameters for the weakening control of rock bursts. For the purpose of prevention, key technical parameters of directional hydraulic fracturing are revealed. Based on these results, as well as those from deep-hole controlled blasting in coal seams and rock, integrated control techniques were established and anti-impact hydraulic props, suitable for roadways subject to hazards from rockbursts have also been developed. These technologies have been widely used in most coal mines in China, subject to these hazards and have achieved remarkable economic and social benefits. 28 refs., 9 figs., 1 tab.

  5. Accurate thermodynamic characterization of a synthetic coal mine methane mixture

    International Nuclear Information System (INIS)

    Hernández-Gómez, R.; Tuma, D.; Villamañán, M.A.; Mondéjar, M.E.; Chamorro, C.R.

    2014-01-01

    Highlights: • Accurate density data of a 10 components synthetic coal mine methane mixture are presented. • Experimental data are compared with the densities calculated from the GERG-2008 equation of state. • Relative deviations in density were within a 0.2% band at temperatures above 275 K. • Densities at 250 K as well as at 275 K and pressures above 10 MPa showed higher deviations. -- Abstract: In the last few years, coal mine methane (CMM) has gained significance as a potential non-conventional gas fuel. The progressive depletion of common fossil fuels reserves and, on the other hand, the positive estimates of CMM resources as a by-product of mining promote this fuel gas as a promising alternative fuel. The increasing importance of its exploitation makes it necessary to check the capability of the present-day models and equations of state for natural gas to predict the thermophysical properties of gases with a considerably different composition, like CMM. In this work, accurate density measurements of a synthetic CMM mixture are reported in the temperature range from (250 to 400) K and pressures up to 15 MPa, as part of the research project EMRP ENG01 of the European Metrology Research Program for the characterization of non-conventional energy gases. Experimental data were compared with the densities calculated with the GERG-2008 equation of state. Relative deviations between experimental and estimated densities were within a 0.2% band at temperatures above 275 K, while data at 250 K as well as at 275 K and pressures above 10 MPa showed higher deviations

  6. Virginia big-eared bats (Corynorhinus townsendii virginianus) roosting in abandoned coal mines in West Virginia

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, J.B.; Edwards, J.W.; Wood, P.B. [West Virginia University, Morgantown, WV (US). Wildlife & Fisheries Resources Programme

    2005-07-01

    We surveyed bats at 36 abandoned coal mines during summer 2002 and 47 mines during fall 2002 at New River Gorge National River and Gauley River National Recreation Area, WV. During summer, we captured three federally endangered Virginia big-eared bats at two mine entrances, and 25 were captured at 12 mine entrances during fall. These represent the first documented captures of this species at coal mines in West Virginia. Future survey efforts conducted throughout the range of the Virginia big-eared bat should include abandoned coal mines.

  7. Safety Psychology Applicating on Coal Mine Safety Management Based on Information System

    Science.gov (United States)

    Hou, Baoyue; Chen, Fei

    In recent years, with the increase of intensity of coal mining, a great number of major accidents happen frequently, the reason mostly due to human factors, but human's unsafely behavior are affected by insecurity mental control. In order to reduce accidents, and to improve safety management, with the help of application security psychology, we analyse the cause of insecurity psychological factors from human perception, from personality development, from motivation incentive, from reward and punishment mechanism, and from security aspects of mental training , and put forward countermeasures to promote coal mine safety production,and to provide information for coal mining to improve the level of safety management.

  8. Reclamation of soils influenced by coal mining in Southern European Russia

    Science.gov (United States)

    Alekseenko, Vladimir; Bech, Jaume; Alekseenko, Alexey; Shvydkaya, Natalya; Roca, Núria

    2016-04-01

    In the recent decades, the concentrations of metals have increased in such media of biosphere as atmosphere, hydrosphere, pedosphere. The greatest geochemical changes have occurred in soils, which are the deposing medium where the high concentrations of metals are saved for years after their direct human use. Mining sites and beneficiation zones are the areas of the highest concentrations of metals in soils. Coal mining areas in the European part of Russia (Rostov region) were selected for a detailed consideration. Soil samples were taken from the uppermost soil horizons: layer of 0-30 cm. The soil samples were analysed for gross concentrations of Cu, Zn, Pb, Ag, Sn, Mo, Ba, Co, Ni, Mn, Ti, V, Cr, Ga, P, Li, Sr, Y, Yb, Nb, Sc, and Zr, using emission spectral analysis. All ordinary analyses were carried out in the certified and accredited laboratory. The external control was conducted by the X-ray fluorescence, gravimetric, and neutron activation analyses. Calculation of random and systematic errors showed high analyses repeatability and correctness. Several cases of self-purification of soils and restoration of landscapes were discussed. The way of remediation through the flooding of mining sites with water was investigated as well as filling of natural relief depressions with soils and dumps. The process of Technosols remediation at the sites occupied by tailings of waste heaps was considered separately. In conclusion: 1. The dominant contemporary way of remediation in Southern European Russia does not prevent the spread of metals through the decades. The modern underground coal mining leads to the destruction of soils in the area directly occupied by wastes and by rock dumps located nearby. 2. Soils have not formed yet as a result of self-restoration at the waste heaps at the age of 50 years, spontaneously combusted decades ago. The vegetation formed during this time virtually eliminates the occurrence of any significant soil-forming process. The ponds formed by

  9. Comparative Assessment of Three Nonlinear Approaches for Landslide Susceptibility Mapping in a Coal Mine Area

    Directory of Open Access Journals (Sweden)

    Qiaomei Su

    2017-07-01

    Full Text Available Landslide susceptibility mapping is the first and most important step involved in landslide hazard assessment. The purpose of the present study is to compare three nonlinear approaches for landslide susceptibility mapping and test whether coal mining has a significant impact on landslide occurrence in coal mine areas. Landslide data collected by the Bureau of Land and Resources are represented by the X, Y coordinates of its central point; causative factors were calculated from topographic and geologic maps, as well as satellite imagery. The five-fold cross-validation method was adopted and the landslide/non-landslide datasets were randomly split into a ratio of 80:20. From this, five subsets for 20 times were acquired for training and validating models by GIS Geostatistical analysis methods, and all of the subsets were employed in a spatially balanced sample design. Three landslide models were built using support vector machine (SVM, logistic regression (LR, and artificial neural network (ANN models by selecting the median of the performance measures. Then, the three fitted models were compared using the area under the receiver operating characteristics (ROC curves (AUC and the performance measures. The results show that the prediction accuracies are between 73.43% and 87.45% in the training stage, and 67.16% to 73.13% in the validating stage for the three models. AUCs vary from 0.807 to 0.906 and 0.753 to 0.944 in the two stages, respectively. Additionally, three landslide susceptibility maps were obtained by classifying the range of landslide probabilities into four classes representing low (0–0.02, medium (0.02–0.1, high (0.1–0.85, and very high (0.85–1 probabilities of landslides. For the distributions of landslide and area percentages under different susceptibility standards, the SVM model has more relative balance in the four classes compared to the LR and the ANN models. The result reveals that the SVM model possesses better

  10. Fiscal 1997 technological survey report. Engineer exchange project - coal mine technological field (Advanced coal producing country survey - U.S.A. survey); 1997 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) senshin santankoku chosa. Beikoku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    While the introduction and adaptation of the Longwall excavation technology were carried forward for coal producing countries in the Pacific region, U.S.A. information was collected by making tours of coal mines in the West and Washington/Colorado/Utah States, with the intention of ascertaining technological trend so as to carry out efficient technological transfer, and for the purpose of replenishing the contents and contributing to the smooth implementation of the engineer exchange project in 'coal mine technological field'. The coal reserves are 400 billion tons, with 840 million tons produced and with 80 million tons exported; not less than 56% of the U.S. domestic electricity rests on coal. Production by open-pit mining is the majority while the output by underground mining is 38%; the Longwall method has increased as a digging method, taking 18% of all digging output. The productivity is 4.24 ton/person per day and ranks as the world highest. The coal mining technological trend in the U.S. can be summarized as follows. The coal mining output in the West is increasing, with the number of mines decreasing, so that the output per mine is increasing. With the output ratio by open-pit mining increasing, the digging method in the mine is being changed to the Longwall. (NEDO)

  11. Industrial hygiene support of underground operations at the Nevada Test Site

    International Nuclear Information System (INIS)

    Porter, P.F.

    1992-01-01

    The Industrial Hygiene Section of the Health Protection Department provides industrial hygiene support of underground operations at the Nevada Test Site. This report describes support operations and summarizes the industrial hygiene data collected from July 31, 1989 through June 30, 1991. Air quality data were collected by means of personnel sampling by active and passive techniques using various kinds of industrial hygiene instrumentation and through localized and general area monitoring. The data collected were used to evaluate underground air quality and quantity requirements; evaluate worker exposures to a variety of air contaminants; determine the applicability and effectiveness of personal protective equipment

  12. Temporal and spatial changes of land use and landscape in a coal mining area in Xilingol grassland

    Science.gov (United States)

    Guan, Chunzhu; Zhang, Baolin; Li, Jiannan; Zhao, Junling

    2017-01-01

    Coal mining, particularly surface mining, inevitably disturbs land. According to Landsat images acquired over Xilingol grassland in 2005, 2009 and 2015, land uses were divided into seven classes, i. e., open stope, stripping area, waste-dump area, mine industrial area, farmland, urban area and the original landscape (grassland), using supervised classification and human-computer interactive interpretation. The overall classification accuracies were 97.72 %, 98.43 % and 96.73 %, respectively; the Kappa coefficients were 0.95, 0.97 and 0.95, respectively. Analysis on LUCC (Land Use and Cover Change) showed that surface coal mining disturbed grassland ecosystem: grassland decreased by 8661.15 hm2 in 2005-2015. The area and proportion of mining operation areas (open stope, stripping area, waste-dump area, mine industrial field) increased, but those of grassland decreased continuously. Transfer matrix of land use changes showed that waste-dump had the largest impacts in mining disturbance, and that effective reclamation of waste-dump areas would mitigate eco-environment destruction, as would be of great significance to protect fragile grassland eco-system. Six landscape index showed that landscape fragmentation increased, and the influences of human activity on landscape was mainly reflected in the expansion of mining area and urban area. Remote sensing monitoring of coal surface mining in grassland would accurately demonstrate the dynamics and trend of LUCC, providing scientific supports for ecological reconstruction in surface mining area.

  13. Information from geology: Implications for soil formation and rehabilitation in the post coal mining environment, Bowen Basin, Australia

    International Nuclear Information System (INIS)

    Spain, A.V.; Esterle, J.; McLennan, T.P.T.

    1995-01-01

    The coal mining industry is likely to disturb as much as 60,000 ha of the Bowen Basin up to the year 2000. While comprising only a small proportion of the approximately 32,000 km 2 of the Bowen Basin, this considerable area will eventually need to be rehabilitated by creating appropriate land forms with a stabilizing and self-sustaining cover of vegetation. The job of restoring the disturbed area will fall to the practitioners of rehabilitation science. This paper briefly outlines the actual and potential significance of geological information to rehabilitation practice in the open-cut coal mining industry of the Bowen Basin. It focuses particularly on the problems of soil formation and the consequent limitations to ecosystem development due to the nature of the overburden materials and the environment. Lastly, it describes some of the distinctive features of the mine-soils of the area. Geological information can assist in the identification, classification, description and behaviour of post-mining materials. Potential inputs are not restricted to these and there is scope for wider inputs to management of the mining environment although the interface with biology requires further development. (author). 4 figs., 31 refs

  14. Coal mining situation in the Federal Republic of Germany. The 1st quarter 2015

    International Nuclear Information System (INIS)

    2015-01-01

    The paper reports on the coal mining in the Federal Republic of Germany in the 1st quarter of 2015. Statistical data are presented for mining, exports and imports of hard coal and lignite and for employees.

  15. Coal mining situation in the Federal Republic of Germany. The 1st quarter 2017

    International Nuclear Information System (INIS)

    2017-01-01

    The paper reports on the coal mining in the Federal Republic of Germany in the 1st quarter of 2017. Statistical data are presented for mining, exports and imports of hard coal and lignite and for employees.

  16. The effects of coal mining on the landscapes of the Ostrava Region

    Czech Academy of Sciences Publication Activity Database

    Martinec, Petr; Schejbalová, Božena; Hortvík, Karel; Maníček, J.

    2005-01-01

    Roč. 13, č. 2 (2005), s. 13-26 ISSN 1210-8812 Institutional research plan: CEZ:AV0Z30860518 Keywords : Ostrava region * coal mining * methane emission * mine waters Subject RIV: DB - Geology ; Mineralogy

  17. Evaluation of remediation of coal mining wastewater by chitosan microspheres using biomarkers

    Energy Technology Data Exchange (ETDEWEB)

    Benassi, J.C.; Laus, R.; Geremias, R.; Lima, P.L.; Menezes, C.T.B.; Laranjeira, M.C.M.; Wilhelm, D.; Favere, V.T.; Pedrosa, R.C. [Universidade Federal de Santa Catarina, Florianopolis (Brazil)

    2006-11-15

    The aim of this work was to evaluate the remediation of mining wastewater effluents by chitosan microspheres using biomarkers of exposure and effect. DNA damage (Comet assay) and several biomarkers of oxidative stress, such as lipoperoxidation levels (TBARS), superoxide dismutase (SOD), catalase (CAT), and glutathione S-transferase (GST) activities, and contents of reduced glutathione (GSH), were measured in blood and liver of tilapia (Oreochromis niloticus) exposed for 7, 15, and 30 days to dechlorinated tap water, 10% coal mining wastewater (CMW), and coal mining wastewater treated with chitosan microspheres (RCM). The results obtained indicated that the use of oxidative stress biomarkers were useful tools for the toxicity evaluation of coal mining effluents and also suggest that chitosan microspheres may be used as an alternative approach for remediation of coal mining wastewaters.

  18. Genotoxic effects in wild rodents (Rattus rattus and Mus musculus) in an open coal mining area.

    Science.gov (United States)

    León, Grethel; Pérez, Lyda Espitia; Linares, Juan Carlos; Hartmann, Andreas; Quintana, Milton

    2007-06-15

    Coal is a mixture of a variety of compounds containing mutagenic and carcinogenic polycyclic aromatic hydrocarbons. Exposure to coal is considered as an important non-cellular and cellular source of reactive oxygen species that can induce DNA damage. In addition, spontaneous combustion can occur in coal mining areas, further releasing compounds with detrimental effects on the environment. In this study the comet assay was used to investigate potential genotoxic effects of coal mining activities in peripheral blood cells of the wild rodents Rattus rattus and Mus musculus. The study was conducted in a coal mining area of the Municipio de Puerto Libertador, South West of the Departamento de Cordoba, Colombia. Animals from two areas in the coal mining zone and a control area located in the Municipio de Lorica were investigated. The results showed evidence that exposure to coal results in elevated primary DNA lesions in blood cells of rodents. Three different parameters for DNA damage were assessed, namely, DNA damage index, migration length and percentage damaged cells. All parameters showed statistically significantly higher values in mice and rats from the coal mining area in comparison to the animals from the control area. The parameter "DNA Damage Index" was found to be most sensitive and to best indicate a genotoxic hazard. Both species investigated were shown to be sensitive indicators of environmental genotoxicity caused by coal mining activities. In summary, our study constitutes the first investigation of potential genotoxic effects of open coal mining carried out in Puerto Libertador. The investigations provide a guide for measures to evaluate genotoxic hazards, thereby contributing to the development of appropriate measures and regulations for more careful operations during coal mining.

  19. Review : Pollution due to Coal Mining Activity and its Impact on Environment

    OpenAIRE

    Andi Arif Setiawan; Dedik Budianta; Dwi Putro Priadi; Suheryanto

    2018-01-01

    Utilization of natural resources in the form of coal mines has a positive impact on economic and energy development, in addition to coal mining activities have a negative impact on the environment that result in environmental pollution in soil, water, and air. Pollution begins when clearing land, taking exploitation, transporting, stockpile and when the coal is burned. When land clearing causes damage to forest ecosystems. At the time of exploitation impact on air pollution by coal dust parti...

  20. First aid to miners suffering from overheating in deep coal mines

    Energy Technology Data Exchange (ETDEWEB)

    Makartsev, V.I.; Tsepurdei, A.A.; Zabolotnii, V.N.; Mozhaev, G.A.; Gridin, V.S. (Vsesoyuznyi Nauchno-Issledovatel' skii Institut Gornospasatel' nogo Dela (Russian Federation))

    1993-03-01

    Describes the symptoms of hyperthermia and approaching thermal shock in coal miners working in deep coal mines. First aid is given to miners suffering from hyperthermia and thermal shock. It is pointed out that prolonged exposure to elevated temperatures at workplaces can result in thermal exhaustion with a deficit of body fluids and minerals. Thermal exhaustion is characterized by general weakness, headaches, insomnia, sleepiness, choleric mood, emotional upset, tremulous pulse and labored breathing. Preventive measures against overheating in deep coal mines are listed.