A high sensitivity 20Mfps CMOS image sensor with readout speed of 1Tpixel/sec for visualization of ultra-high speed phenomena

Science.gov (United States)

Kuroda, R.; Sugawa, S.

2017-02-01

Ultra-high speed (UHS) CMOS image sensors with on-chop analog memories placed on the periphery of pixel array for the visualization of UHS phenomena are overviewed in this paper. The developed UHS CMOS image sensors consist of 400H×256V pixels and 128 memories/pixel, and the readout speed of 1Tpixel/sec is obtained, leading to 10 Mfps full resolution video capturing with consecutive 128 frames, and 20 Mfps half resolution video capturing with consecutive 256 frames. The first development model has been employed in the high speed video camera and put in practical use in 2012. By the development of dedicated process technologies, photosensitivity improvement and power consumption reduction were simultaneously achieved, and the performance improved version has been utilized in the commercialized high-speed video camera since 2015 that offers 10 Mfps with ISO16,000 photosensitivity. Due to the improved photosensitivity, clear images can be captured and analyzed even under low light condition, such as under a microscope as well as capturing of UHS light emission phenomena.

Ultra-high-speed inversion recovery echo planar MR imaging

International Nuclear Information System (INIS)

Stehling, M.K.; Ordidge, R.J.; Coxon, R.; Chapman, B.; Houseman, A.M.; Guifoyle, D.; Blamire, A.; Gibbs, P.; Mansfield, P.

1988-01-01

Fast two-dimensional FT MR imaging techniques such as fast low-angle shot do not allow inversion recovery (IR). Rapid repetition of low-angle pulses is incompatible with a 180 0 inversion pulse. Echo planar imaging (EPI) can be applied in conjunction with IR, because after preparation of the spin system, a complete image is acquired. Data acquisition in less than 100 msec and real-time display allows interactive optimization of inversion time (4.0-9,000 msec) with little time penalty. The authors have applied IR EPI to the study of the brain, liver, and kidneys in normal volunteers and patients. Technical details are presented, and the applications of this first ultra-high-speed IR technique will be shown

ASBESTOS EXPOSURES DURING ROUTINE FLOOR TILE MAINTENANCE. PART 2: ULTRA HIGH SPEED BURNISHING AND WET-STRIPPING

Science.gov (United States)

This study was conducted to evaluate airborne asbestos concentrations during ultra high speed (UHS) burnishing and wet-stripping of asbestos-containing resilient floor tile under two levels of floor care condition (poor and good). Airborne asbestos concentrations were measured by...

Ultra-high-speed digital in-line holography system applied to particle-laden supersonic underexpanded jet flows

DEFF Research Database (Denmark)

Ingvorsen, Kristian Mark; Buchmann, Nicolas A.; Soria, Julio

2012-01-01

-fluid interactions in these high-speed flows special high performance techniques are required. The present work is an investigation into the applicability of magnified digital in-line holography with ultra-high-speed recording for the study of three-dimensional supersonic particle-laden flows. An optical setup...... × 10mm calibration grid and 120 μm particles on a glass plate. In the case with the calibration grid it is found that accurate determination of the depthwise position is possible. However, when applying the same technique to the particle target, significant problems are encountered. © 2012...

High-speed ultra-wideband wireless signals over fiber systems: photonic generation and DSP detection

DEFF Research Database (Denmark)

Yu, Xianbin; Gibbon, Timothy Braidwood; Tafur Monroy, Idelfonso

2009-01-01

We firstly review the efforts in the literature on ultra-wideband (UWB)-over-fiber systems. Secondly, we present experimental results on photonic generation of high-speed UWB signals by both direct modulation and external optical injecting an uncooled semiconductor laser. Furthermore, we introduce...... the use of digital signal processing (DSP) technology to receive the generated UWB signal at 781.25 Mbit/s. Error-free transmission is achieved....

Single-event transient imaging with an ultra-high-speed temporally compressive multi-aperture CMOS image sensor.

Science.gov (United States)

Mochizuki, Futa; Kagawa, Keiichiro; Okihara, Shin-ichiro; Seo, Min-Woong; Zhang, Bo; Takasawa, Taishi; Yasutomi, Keita; Kawahito, Shoji

2016-02-22

In the work described in this paper, an image reproduction scheme with an ultra-high-speed temporally compressive multi-aperture CMOS image sensor was demonstrated. The sensor captures an object by compressing a sequence of images with focal-plane temporally random-coded shutters, followed by reconstruction of time-resolved images. Because signals are modulated pixel-by-pixel during capturing, the maximum frame rate is defined only by the charge transfer speed and can thus be higher than those of conventional ultra-high-speed cameras. The frame rate and optical efficiency of the multi-aperture scheme are discussed. To demonstrate the proposed imaging method, a 5×3 multi-aperture image sensor was fabricated. The average rising and falling times of the shutters were 1.53 ns and 1.69 ns, respectively. The maximum skew among the shutters was 3 ns. The sensor observed plasma emission by compressing it to 15 frames, and a series of 32 images at 200 Mfps was reconstructed. In the experiment, by correcting disparities and considering temporal pixel responses, artifacts in the reconstructed images were reduced. An improvement in PSNR from 25.8 dB to 30.8 dB was confirmed in simulations.

Ultra-high-speed digital in-line holography system applied to particle-laden supersonic underexpanded jet flows

DEFF Research Database (Denmark)

Ingvorsen, Kristian Mark; Buchmann, Nicolas A.; Soria, Julio

2012-01-01

-fluid interactions in these high-speed flows special high performance techniques are required. The present work is an investigation into the applicability of magnified digital in-line holography with ultra-high-speed recording for the study of three-dimensional supersonic particle-laden flows. An optical setup...... × 10mm calibration grid and 120 μm particles on a glass plate. In the case with the calibration grid it is found that accurate determination of the depthwise position is possible. However, when applying the same technique to the particle target, significant problems are encountered....

Self-monitoring of driving speed.

Science.gov (United States)

Etzioni, Shelly; Erev, Ido; Ishaq, Robert; Elias, Wafa; Shiftan, Yoram

2017-09-01

In-vehicle data recorders (IVDR) have been found to facilitate safe driving and are highly valuable in accident analysis. Nevertheless, it is not easy to convince drivers to use them. Part of the difficulty is related to the "Big Brother" concern: installing IVDR impairs the drivers' privacy. The "Big Brother" concern can be mitigated by adding a turn-off switch to the IVDR. However, this addition comes at the expense of increasing speed variability between drivers, which is known to impair safety. The current experimental study examines the significance of this negative effect of a turn-off switch under two experimental settings representing different incentive structures: small and large fines for speeding. 199 students were asked to participate in a computerized speeding dilemma task, where they could control the speed of their "car" using "brake" and "speed" buttons, corresponding to automatic car foot pedals. The participants in two experimental conditions had IVDR installed in their "cars", and were told that they could turn it off at any time. Driving with active IVDR implied some probability of "fines" for speeding, and the two experimental groups differed with respect to the fine's magnitude, small or large. The results indicate that the option to use IVDR reduced speeding and speed variance. In addition, the results indicate that the reduction of speed variability was maximal in the small fine group. These results suggest that using IVDR with gentle fines and with a turn-off option maintains the positive effect of IVDR, addresses the "Big Brother" concern, and does not increase speed variance. Copyright © 2017 Elsevier Ltd. All rights reserved.

Implementation of a sliding-mode-based position sensorless drive for high-speed micro permanent-magnet synchronous motors.

Science.gov (United States)

Chi, Wen-Chun; Cheng, Ming-Yang

2014-03-01

Due to issues such as limited space, it is difficult if it is not impossible to employ a position sensor in the drive control of high-speed micro PMSMs. In order to alleviate this problem, this paper analyzes and implements a simple and robust position sensorless field-oriented control method of high-speed micro PMSMs based on the sliding-mode observer. In particular, the angular position and velocity of the rotor of the high-speed micro PMSM are estimated using the sliding-mode observer. This observer is able to accurately estimate rotor position in the low speed region and guarantee fast convergence of the observer in the high speed region. The proposed position sensorless control method is suitable for electric dental handpiece motor drives where a wide speed range operation is essential. The proposed sensorless FOC method is implemented using a cost-effective 16-bit microcontroller and tested in a prototype electric dental handpiece motor. Several experiments are performed to verify the effectiveness of the proposed method. © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

Research and Application of WCF Technology in Data Acquisition of Ultra-high Speed Packaging Machine

Directory of Open Access Journals (Sweden)

Qian Jie

2016-01-01

Full Text Available By introducing WCF technology on data acquisition of ultra-high speed packaging machine, data acquisition system reads dates of machine in polling mode through the WCF client, which can achieve accurate data collection, and effectively isolate the data acquisition system and the machine control system. It enhances the security of data interaction between systems, but also reduces the coupling degree between systems.

Ultra-high speed all-optical signal processing using silicon waveguides and a carbon nanotubes based mode-locked laser

DEFF Research Database (Denmark)

Ji, Hua

This thesis concerns the use of nano-engineered silicon waveguides for ultra-high speed optical serial data signal processing. The fundamental nonlinear properties of nano-engineered silicon waveguides are characterized. Utilizing the nonlinear effect in nano-engineered silicon waveguides for dem...

Efficient Ultra-High Speed Communication with Simultaneous Phase and Amplitude Regenerative Sampling (SPARS)

Science.gov (United States)

Carlowitz, Christian; Girg, Thomas; Ghaleb, Hatem; Du, Xuan-Quang

2017-09-01

For ultra-high speed communication systems at high center frequencies above 100 GHz, we propose a disruptive change in system architecture to address major issues regarding amplifier chains with a large number of amplifier stages. They cause a high noise figure and high power consumption when operating close to the frequency limits of the underlying semiconductor technologies. Instead of scaling a classic homodyne transceiver system, we employ repeated amplification in single-stage amplifiers through positive feedback as well as synthesizer-free self-mixing demodulation at the receiver to simplify the system architecture notably. Since the amplitude and phase information for the emerging oscillation is defined by the input signal and the oscillator is only turned on for a very short time, it can be left unstabilized and thus come without a PLL. As soon as gain is no longer the most prominent issue, relaxed requirements for all the other major components allow reconsidering their implementation concepts to achieve further improvements compared to classic systems. This paper provides the first comprehensive overview of all major design aspects that need to be addressed upon realizing a SPARS-based transceiver. At system level, we show how to achieve high data rates and a noise performance comparable to classic systems, backed by scaled demonstrator experiments. Regarding the transmitter, design considerations for efficient quadrature modulation are discussed. For the frontend components that replace PA and LNA amplifier chains, implementation techniques for regenerative sampling circuits based on super-regenerative oscillators are presented. Finally, an analog-to-digital converter with outstanding performance and complete interfaces both to the analog baseband as well as to the digital side completes the set of building blocks for efficient ultra-high speed communication.

Design and simulation of the direct drive servo system

Science.gov (United States)

Ren, Changzhi; Liu, Zhao; Song, Libin; Yi, Qiang; Chen, Ken; Zhang, Zhenchao

2010-07-01

As direct drive technology is finding their way into telescope drive designs for its many advantages, it would push to more reliable and cheaper solutions for future telescope complex motion system. However, the telescope drive system based on the direct drive technology is one high integrated electromechanical system, which one complex electromechanical design method is adopted to improve the efficiency, reliability and quality of the system during the design and manufacture circle. The telescope is one ultra-exact, ultra-speed, high precision and huge inertial instrument, which the direct torque motor adopted by the telescope drive system is different from traditional motor. This paper explores the design process and some simulation results are discussed.

Ultra-high-speed imaging of the brain by the echo planar technique

International Nuclear Information System (INIS)

Worthington, B.S.; Stehling, M.K.; Ordidge, R.J.; Coxon, R.; Howseman, A.M.; Chapman, B.; Turner, R.; Firth, J.L.; Mansfield, P.

1988-01-01

Reduced examination time, greater patient tolerance and throughput, and the ability to study vascular and cerebrospinal fluid (CSF) flow phenomena are important advantages of ultra-high-speed brain imaging. The EPI derivatives BEST and MBEST create a complete 128 X 128-pixel image in 64 msec and 128 msec, respectively. In BEST images, T2 weighting is altered by adjusting the echo time, modulus BEST images have intrinsic T2 weighting. Repetition time alterations provide variable T1 weighting in both. Volunteer and patient studies illustrate how selective contrast manipulation allows excellent discrimination between gray and white matter and the brain and the CSF, enabling the demonstration of pathology

Ultra high speed framing photographs of laser produced plasmas using a picosecond optical shutter

International Nuclear Information System (INIS)

Gillman, G.B.; Ramsden, S.A.

1975-01-01

A study has been carried out of the spatial transmission properties of the optical Kerr effect shutter and it has been used to take ultra high speed framing photographs of laser produced plasmas in air and from solid targets. With a 1cm long CS 2 cell of aperture 5cm 2 a transmission of approximately 5% and an on/off contrast ratio of 10 4 was obtained. An image intensifier was necessary to obtain adequately exposed photographs of the plasma and the overall spatial resolution of the system was approximately 2μ. (author)

The clinical potential of ultra-high-speed echo-planar imaging

International Nuclear Information System (INIS)

Worthington, B.S.; Firth, J.L.; Morris, G.K.; Johnson, I.R.; Coxon, R.; Blamire, A.M.; Gibbs, P.; Mansfield, P.

1990-01-01

Ultra-high-speed echo-planar imaging (EPI) allows acquisition of a complete two-dimensional image in 64 to 128 ms devoid of movement artefact and without sacrifice of contrast due to relaxation time effects. In conventional whole-body MRI, however, obtrusive movement artefact and extended imaging time, resulting from the need to apply multiple sequences to facilitate lesion detection and pathological characterization, remain limitations. Reduced total examination time increases patient tolerance and throughput; furthermore optimization of contrast to achieve maximal conspicuity of particular features in liver or brain pathology is achieved simply and interactively by real time adjustment of the imaging parameters. The method provides the opportunity to study in real time dynamic events such as flow phenomena in the vascular and cerebrospinal fluid compartments of the brain as well as the kinetics of administered contrast agents. EPI is the only means of capturing the irregular motion of aperiodic cardiac events and bowel peristalsis. (author)

New insights into mechanisms of sonothrombolysis using ultra-high-speed imaging.

Science.gov (United States)

Chen, Xucai; Leeman, Jonathan E; Wang, Jianjun; Pacella, John J; Villanueva, Flordeliza S

2014-01-01

Thrombotic arterial occlusion is the principal etiology for acute cardiovascular syndromes such as stroke, myocardial infarction and unstable angina. Exposing the thrombus to ultrasound and microbubbles facilitates thrombus disruption, making "sonothrombolysis" a potentially powerful therapeutic strategy for thromboembolic diseases. However, optimization of such a strategy, and hence clinical translation, is constrained by an incomplete understanding of mechanisms by which ultrasound-induced microbubble vibrations disrupt blood clots. We posit that previously reported sonothrombolytic efficacy using inertial cavitation regimes was due, at least in part, to mechanical clot disruption by oscillating microbubbles. To test this hypothesis, we optically characterized lipid microbubble interactions with thrombus in the presence of ultrasound using a recently developed ultra-high-speed microscopy imaging system to visualize microbubble acoustic behaviors at megahertz frame rates. A microscope/acoustic stage designed for the system allowed an experimentally created thrombus and microbubbles to be insonified at a co-localized acoustic and optical focus during synchronized high-speed imaging. Under inertial cavitation conditions, large-amplitude microbubble oscillations caused thrombus deformation and pitting. Acoustic radiation forces (Bjerknes forces) further augmented microbubble-thrombus interaction. These observations suggest that a direct mechanical effect of oscillating lipid microbubbles on an adjacent thrombus may play a role in mediating clot disruption in the presence of specific ultrasound conditions. Copyright © 2014 World Federation for Ultrasound in Medicine & Biology. Published by Elsevier Inc. All rights reserved.

Advances in indirect detector systems for ultra high-speed hard X-ray imaging with synchrotron light

Science.gov (United States)

Olbinado, M. P.; Grenzer, J.; Pradel, P.; De Resseguier, T.; Vagovic, P.; Zdora, M.-C.; Guzenko, V. A.; David, C.; Rack, A.

2018-04-01

We report on indirect X-ray detector systems for various full-field, ultra high-speed X-ray imaging methodologies, such as X-ray phase-contrast radiography, diffraction topography, grating interferometry and speckle-based imaging performed at the hard X-ray imaging beamline ID19 of the European Synchrotron—ESRF. Our work highlights the versatility of indirect X-ray detectors to multiple goals such as single synchrotron pulse isolation, multiple-frame recording up to millions frames per second, high efficiency, and high spatial resolution. Besides the technical advancements, potential applications are briefly introduced and discussed.

On the reduced-complexity of LDPC decoders for ultra-high-speed optical transmission.

Science.gov (United States)

Djordjevic, Ivan B; Xu, Lei; Wang, Ting

2010-10-25

We propose two reduced-complexity (RC) LDPC decoders, which can be used in combination with large-girth LDPC codes to enable ultra-high-speed serial optical transmission. We show that optimally attenuated RC min-sum sum algorithm performs only 0.46 dB (at BER of 10(-9)) worse than conventional sum-product algorithm, while having lower storage memory requirements and much lower latency. We further study the use of RC LDPC decoding algorithms in multilevel coded modulation with coherent detection and show that with RC decoding algorithms we can achieve the net coding gain larger than 11 dB at BERs below 10(-9).

Solutions for ultra-high speed optical wavelength conversion and clock recovery

DEFF Research Database (Denmark)

Oxenløwe, Leif Katsuo; Galili, Michael; Mulvad, Hans Christian Hansen

2006-01-01

This paper reports on our recent advances in ultra-fast optical communications relying on ultra-short pulses densely stacked in ultra-high bit rate serial data signals at a single wavelength. The paper describes details in solutions for the network functionalities of wavelength conversion and clock...... recovery at bit rates up to 320 Gb/s...

Gear Design Effects on the Performance of High Speed Helical Gear Trains as Used in Aerospace Drive Systems

Science.gov (United States)

Handschuh, R.; Kilmain, C.; Ehinger, R.; Sinusas, E.

2013-01-01

The performance of high-speed helical gear trains is of particular importance for tiltrotor aircraft drive systems. These drive systems are used to provide speed reduction / torque multiplication from the gas turbine output shaft and provide the necessary offset between these parallel shafts in the aircraft. Four different design configurations have been tested in the NASA Glenn Research Center, High Speed Helical Gear Train Test Facility. The design configurations included the current aircraft design, current design with isotropic superfinished gear surfaces, double helical design (inward and outward pumping), increased pitch (finer teeth), and an increased helix angle. All designs were tested at multiple input shaft speeds (up to 15,000 rpm) and applied power (up to 5,000 hp). Also two lubrication, system-related, variables were tested: oil inlet temperature (160 to 250 degF) and lubricating jet pressure (60 to 80 psig). Experimental data recorded from these tests included power loss of the helical system under study, the temperature increase of the lubricant from inlet to outlet of the drive system and fling off temperatures (radially and axially). Also, all gear systems were tested with and without shrouds around the gears. The empirical data resulting from this study will be useful to the design of future helical gear train systems anticipated for next generation rotorcraft drive systems.

All-Optical Ultra-High-Speed OFDM to Nyquist-WDM Conversion Based on Complete Optical Fourier Transformation

DEFF Research Database (Denmark)

Guan, Pengyu; Røge, Kasper Meldgaard; Mulvad, Hans Christian Hansen

2016-01-01

We propose a novel all-optical ultra-high-speed orthogonal frequency-division multiplexing (OFDM) to Nyquist wavelength-division multiplexing (Nyquist-WDM) conversion scheme, achieved by exchanging the temporal and spectral profiles using a complete optical Fourier transformation (OFT). This scheme...... enables high-speed OFDM to Nyquist-WDM conversion without complex optical/electrical/optical conversion. The all-optical OFDM transmitter is based on the generation of OFDM symbols with a low duty cycle by rectangular temporal gating, which in combination with optical time-division multiplexing yields...... a higher symbol-rate OFDM signal. In the receiver, the converted Nyquist-WDM super-channel is WDM demultiplexed into individual Nyquist-WDM channels using a rectangular optical bandpass filter, followed by optical sampling at the intersymbol-interference free point. In the experimental demonstration...

Investigating Car Users’ Driving Behaviour through Speed Analysis

Directory of Open Access Journals (Sweden)

Laura Eboli

2017-04-01

Full Text Available Speed has been identified for a long time as a key risk factor in road traffic: inappropriate speeds contribute to a relevant part of traffic accidents. Many literature studies have focused on the relationship between speed and accident risk. Starting from this consideration this paper investigates traffic accident risk by analysing the travelling speeds recorded by real tests on the road. A survey was conducted to collect experimental speed values in a real context. A specific road segment, belonging to an Italian rural two-lane road, was repeatedly run by 27 drivers in order to collect the instantaneous speed values for each trajectory. Smartphone-equipped vehicles were used to record continuous speed data. The recorded data were used to calculate: the average speed, 50th and 85th percentile speed for each geometric element of the analysed road segment. The main result of the research is the classification of car users’ driving behaviour based on the speed values. By using the above mentioned ranges of speed, the classification provides three types of driving behaviour: safe, unsafe, and safe but potentially dangerous. It was found that only four drivers feature “safe” behaviour, driving in a safe manner on most of the road elements. However, the major part of drivers, even if they feature safe behaviour, could be dangerous for other drivers because they drive at very low speeds.

An ultra-high-vacuum multiple grating chamber and scan drive with improved grating change

International Nuclear Information System (INIS)

Hulbert, S.L.; Holly, D.J.; Middleton, F.H.; Wallace, D.J.; Wisconsin Univ., Stoughton, WI; Wisconsin Univ., Stoughton, WI

1989-01-01

We describe a new grating chamber and scan drive which has been designed, built, and tested by Physical Sciences Laboratory of the University of Wisconsin for the new high flux, high-resolution spectroscopy branch line of the TOK hybrid wiggler/undulator on the NSLS VUV ring. The chamber will contain spherical gratings to be used in the Spherical Grating Monochromator (SGM) configuration introduced by Chen and Sette. The grating chamber houses five 180 mm x 35 mm x 30 mm gratings capable of scanning a range of 12 degree (-14 degree to +8 degree with respect to the incoming beam direction) for VUV and soft X-ray diffraction. The gratings can be switched and precisely indexed while under ultra-high vacuum (UHV) at any scan angle and are mechanically isolated from the vacuum chamber to prevent inaccuracies due to chamber distortions. The gratings can separately be adjusted for height, yaw, pitch, and roll, with the latter three performed while in vacuo. The scan drive provides a resolution of 0.03 arc sec with linearity over the 12 degree range of ∼1.5 arc sec and absolute reproducibility of 1 arc sec. 5 refs., 5 figs

Motor models and transient analysis for high-temperature, superconductor switch-based adjustable speed drive applications. Final report

International Nuclear Information System (INIS)

Bailey, J.M.

1996-06-01

New high-temperature superconductor (HTSC) technology may allow development of an energy-efficient power electronics switch for adjustable speed drive (ASD) applications involving variable-speed motors, superconducting magnetic energy storage systems, and other power conversion equipment. This project developed a motor simulation module for determining optimal applications of HTSC-based power switches in ASD systems

Comparing a driving simulator to the real road regarding distracted driving speed

NARCIS (Netherlands)

Knapper, Allert; Christoph, Michiel; Hagenzieker, Marjan; Brookhuis, Karel

2015-01-01

Relative and absolute validity of a driving simulator were assessed regarding effects on mean speed and speed variation during distracting secondary tasks, and normal driving. 16 participants drove the same route four times, twice in a simulator and twice in the real world. They performed way

Comparing a driving simulator to the real road regarding distracted driving speed.

NARCIS (Netherlands)

Knapper, A. Christoph, M. Hagenzieker, M. & Brookhuis, K.

2015-01-01

Relative and absolute validity of a driving simulator were assessed regarding effects on mean speed and speed variation during distracting secondary tasks, and normal driving. 16 participants drove the same route four times, twice in a simulator and twice in the real world. They performed way

Simplified Fuzzy Control for Flux-Weakening Speed Control of IPMSM Drive

Directory of Open Access Journals (Sweden)

M. J. Hossain

2011-01-01

Full Text Available This paper presents a simplified fuzzy logic-based speed control scheme of an interior permanent magnet synchronous motor (IPMSM above the base speed using a flux-weakening method. In this work, nonlinear expressions of d-axis and q-axis currents of the IPMSM have been derived and subsequently incorporated in the control algorithm for the practical purpose in order to implement fuzzy-based flux-weakening strategy to operate the motor above the base speed. The fundamentals of fuzzy logic algorithms as related to motor control applications are also illustrated. A simplified fuzzy speed controller (FLC for the IPMSM drive has been designed and incorporated in the drive system to maintain high performance standards. The efficacy of the proposed simplified FLC-based IPMSM drive is verified by simulation at various dynamic operating conditions. The simplified FLC is found to be robust and efficient. Laboratory test results of proportional integral (PI controller-based IPMSM drive have been compared with the simulated results of fuzzy controller-based flux-weakening IPMSM drive system.

Energy efficiency high speed drives with magnetic bearings; Energieeffizienz durch schnell drehende, magnetgelagerte Antriebe

Energy Technology Data Exchange (ETDEWEB)

Kroll, Matthias [LEViTEC GmbH, Lahnau (Germany)

2011-07-01

In modern purification plans the contamination of the wastewater are biologically removed by supplying oxygen. The clarifier is ventilated by compressors around the clock and approximately 60% of the total energy consumption is used for that. It enables a great opportunity for saving energy. This contribution shows that the use of magnetic centrifugal compressors with high-speed drives leads to significant reduction of energy consumption. In addition, the drive is, due to contact free the magnetic bearings, practically wear- and maintenance-free. By the use of integrated sensors in the magnetic bearings a continuous monitoring of the compressor is implemented. Consequently this drive concept provides not only more efficiency and less energy consumption, but also leads to a higher plant availability. (orig.)

Retrofitting adjustable speed drives for large induction motors

International Nuclear Information System (INIS)

Wuestefeld, M.R.; Merriam, C.H.; Porter, N.S.

2004-01-01

Adjustable speed drives (ASDs) are used in many power plants to control process flow by varying the speed of synchronous and induction motors. In applications where the flow requirements vary significantly, ASDs reduce energy and maintenance requirements when compared with drag valves, dampers or other methods to control flow. Until recently, high horsepower ASDs were not available for induction motors. However, advances in power electronics technology have demonstrated the reliability and cost effectiveness of ASDs for large horsepower induction motors. Emphasis on reducing operation and maintenance costs and increasing the capacity factor of nuclear power plants has led some utilities to consider replacing flow control devices in systems powered by large induction motors with ASDs. ASDs provide a high degree of reliability and significant energy savings in situations where full flow operation is not needed for a substantial part of the time. This paper describes the basic adjustable speed drive technologies available for large induction motor applications, ASD operating experience and retrofitting ASDs to replace the existing GE Boiling Water Reactor recirculation flow control system

Adjustable speed drive study, June 1985 to September 1988. Part 2: Appendices

Science.gov (United States)

Wallace, Alan

1989-08-01

Advances in speed control for motors in recent years, notably those in power electronics, have widened the range of application for several adjustable speed drive (ASD) types to include the smaller horsepower sizes. The dc motor drive, formerly in almost universal use for speed control, is being challenged by the high efficiency induction motor/pulse width modulation (PWM) drive; and for special small horsepower size applications, by the permanent magnet motor/PWM inverter drive or by the switched reluctance motor drive. The main characteristics of the several ASD types suitable for small horsepower size applications are discussed, as well as their unwanted side effects: poor power factor, harmonic distortion of the supply, acoustic noise, and electromagnetic interference. A procedure is recommended for determining which, if any, ASD to use.

Appetitive drives for ultra-processed food products and the ability of text warnings to counteract consumption predispositions.

Science.gov (United States)

David, Isabel A; Krutman, Laura; Fernández-Santaella, María Carmen; Andrade, Jéssica R; Andrade, Eduardo B; Oliveira, Leticia; Pereira, Mirtes G; Gomes, Fabio S; Gleiser, Sonia; Oliveira, José M; Araújo, Renata L; Volchan, Eliane; Braga, Filipe

2018-02-01

The present study aimed to (i) assess the appetitive drives evoked by the visual cues of ultra-processed food and drink products and (ii) investigate whether text warnings reduce appetitive drives and consumers' reported intentions to eat or drink ultra-processed products. In Study I, a well-established psychometric tool was applied to estimate the appetitive drives associated with ultra-processed products using sixty-four image representations. Sixteen product types with four exemplars of a given product were included. Pictures from the International Affective Picture System (IAPS) served as controls. The two exemplars of each product type rated as more appetitive were selected for investigation in the second study. Study II assessed the impact of textual warnings on the appetitive drive towards these thirty-two exemplars. Each participant was exposed to two picture exemplars of the same product type preceded by a text warning or a control text. After viewing each displayed picture, the participants reported their emotional reactions and their intention to consume the product. Controlled classroom experiments SUBJECTS: Undergraduate students (Study I: n 215, 135 women; Study II: n 98, 52 women). In Study I, the pictures of ultra-processed products prompted an appetitive motivation associated with the products' nutritional content. In Study II, text warnings were effective in reducing the intention to consume and the appetitive drive evoked by ultra-processed products. This research provides initial evidence favouring the use of text warnings as a public policy tool to curb the powerful influence of highly appetitive ultra-processed food cues.

Design of rotating mirror for ultra-high speed camera based on dynamic characteristic

International Nuclear Information System (INIS)

Li Chunbo; Chai Jinlong; Liang Yexing; Liu Chunping; Wang Hongzhi; Yu Chunhui; Li Jingzhen; Huang Hongbin

2011-01-01

A systematic design method has been proposed for studying the dynamic design of rotating mirror for ultra-high speed camera. With the finite element software, the numerical analyses of static, modal, harmonic responses and natural frequency sensitivity for the preliminary-designed rotating mirror were done based on the static and dynamic theories. Some experiments were done to verify the results. The physical dimensions of the rotating mirror were modified repeatedly according to the results for designing a new rotating mirror. Then simulation and experiments of fatigue life for the new rotating mirror under alternating force were done. The results show that the maximum static stress is less than the yield stress of the rotating mirror material, which proves the new rotating mirror will not be subjected to static strength failure. However, the results of modal and harmonic response analyses indicate that the dynamic characteristic of the new rotating mirror can not meet the design requirement for the first critical speed is less than the service speed. In all the physical dimensions of the rotating mirror, the circum radius of mirror body and natural frequency are negatively correlated and the degree of correlation is maximal. The first-order natural frequency in- creases from 459.4 Hz to 713.6 Hz, the rate of change is 55.3%, the first critical speed is up to 42 816 r/min, avoiding resonance successfully, and the fatigue strength of the new rotating mirror can meet the design requirement. (authors)

Speed choice and steering behavior in curve driving

NARCIS (Netherlands)

Winsum, W. van; Godthelp, J.

1996-01-01

The relation between speed choice and steering performance during curve negotiation was studied in a driving simulator. The hypothesis was that curve radius and steering competence both affect steering error during curve driving, resulting in compensatory speed choice. In this, the control of safety

Speed-Sensorless DTC-SVM for Matrix Converter Drives With Simple Nonlinearity Compensation

DEFF Research Database (Denmark)

Lee, Kyo Beum; Blaabjerg, Frede; Yoon, Tae-Woong

2007-01-01

This paper presents a new method to improve the sensorless performance of matrix converter drives using a parameter estimation scheme. To improve low-speed sensorless performance, the nonlinearities of a matrix converter drive such as commutation delays, turn-on and turn-off times of switching de...... compensation method is applied for high performance induction motor drives using a 3-kW matrix converter system without a speed sensor. Experimental results are shown to illustrate the feasibility of the proposed strategy....

Adjustable Speed Drives - Future Challenges and Applications

DEFF Research Database (Denmark)

Blaabjerg, Frede; Thoegersen, Paul

2004-01-01

The main trends within Adjustable Drives in industrial and appliance applications for the next decade are discussed based on the newest developments seen on the market and a few historical trends. Different drive configurations are presented and the general demands to adjustable speed drives...

Self-Tuning Speed Regulator for CVC Induction Motor Drive

DEFF Research Database (Denmark)

Bidstrup, N.; Rasmussen, Henrik; Knudsen, Torben

1994-01-01

A self-tuning speed regulator for a current vector controlled induction motor drive has been designed.......A self-tuning speed regulator for a current vector controlled induction motor drive has been designed....

ULTRA-SHARP nonoscillatory convection schemes for high-speed steady multidimensional flow

Science.gov (United States)

Leonard, B. P.; Mokhtari, Simin

1990-01-01

For convection-dominated flows, classical second-order methods are notoriously oscillatory and often unstable. For this reason, many computational fluid dynamicists have adopted various forms of (inherently stable) first-order upwinding over the past few decades. Although it is now well known that first-order convection schemes suffer from serious inaccuracies attributable to artificial viscosity or numerical diffusion under high convection conditions, these methods continue to enjoy widespread popularity for numerical heat transfer calculations, apparently due to a perceived lack of viable high accuracy alternatives. But alternatives are available. For example, nonoscillatory methods used in gasdynamics, including currently popular TVD schemes, can be easily adapted to multidimensional incompressible flow and convective transport. This, in itself, would be a major advance for numerical convective heat transfer, for example. But, as is shown, second-order TVD schemes form only a small, overly restrictive, subclass of a much more universal, and extremely simple, nonoscillatory flux-limiting strategy which can be applied to convection schemes of arbitrarily high order accuracy, while requiring only a simple tridiagonal ADI line-solver, as used in the majority of general purpose iterative codes for incompressible flow and numerical heat transfer. The new universal limiter and associated solution procedures form the so-called ULTRA-SHARP alternative for high resolution nonoscillatory multidimensional steady state high speed convective modelling.

Next-generation technologies for spatial proteomics: Integrating ultra-high speed MALDI-TOF and high mass resolution MALDI FTICR imaging mass spectrometry for protein analysis.

Science.gov (United States)

Spraggins, Jeffrey M; Rizzo, David G; Moore, Jessica L; Noto, Michael J; Skaar, Eric P; Caprioli, Richard M

2016-06-01

MALDI imaging mass spectrometry is a powerful analytical tool enabling the visualization of biomolecules in tissue. However, there are unique challenges associated with protein imaging experiments including the need for higher spatial resolution capabilities, improved image acquisition rates, and better molecular specificity. Here we demonstrate the capabilities of ultra-high speed MALDI-TOF and high mass resolution MALDI FTICR IMS platforms as they relate to these challenges. High spatial resolution MALDI-TOF protein images of rat brain tissue and cystic fibrosis lung tissue were acquired at image acquisition rates >25 pixels/s. Structures as small as 50 μm were spatially resolved and proteins associated with host immune response were observed in cystic fibrosis lung tissue. Ultra-high speed MALDI-TOF enables unique applications including megapixel molecular imaging as demonstrated for lipid analysis of cystic fibrosis lung tissue. Additionally, imaging experiments using MALDI FTICR IMS were shown to produce data with high mass accuracy (z 5000) for proteins up to ∼20 kDa. Analysis of clear cell renal cell carcinoma using MALDI FTICR IMS identified specific proteins localized to healthy tissue regions, within the tumor, and also in areas of increased vascularization around the tumor. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Robust Adaptive Speed Control of Induction Motor Drives

DEFF Research Database (Denmark)

Bidstrup, N.

This thesis concerns speed control of current vector controlled induction motor drives (CVC drives). The CVC drive is an existing prototype drive developed by Danfoss A/S, Transmission Division. Practical tests have revealed that the open loop dynamical properties of the CVC drive are highly......, (LS) identification and generalized predictive control (GPC) has been implemented and tested on the CVC drive. Allthough GPC is a robust control method, it was not possible to maintain specified controller performance in the entire operating range. This was the main reason for investigating truly...... and measurement noise in general, were the major reasons for the drifting parameters. Two approaches was proposed to robustify MASTR2 against the output noise. The first approach consists of filtering the output. Output filtering had a significant effect in simulations, but the robustness against the output noise...

Wind generator with electronic variable-speed drives

Energy Technology Data Exchange (ETDEWEB)

David, A.; Buchheit, N.; Jakobsen, H.

1996-12-31

Variable speed drives have been inserted between the network and the generator on certain recent wind power facilities. They have the following advantages: the drive allows the wind generator to operate at low speed with a significant reduction in acoustic noise, an important point if the facilities are sited near populated areas; the drive optimizes energy transfer, providing a gain of 4 to 10 %; the drive can possibly replace certain mechanical parts (the starting system and it in some cases, the reduction gear); the drive not only provides better transient management in relation to the network for less mechanical stress on the wind generator, it is also able to control reactive power. One commercial drive design sold by several manufacturers has already been installed on several wind generators with outputs of between 150 and 600 kw. In addition, such a solution is extremely well suited to mixed renewable energy systems. This design uses two inverse rectifier type converters and can therefore exchange energy in both directions. The equivalent drive with a single IGBT converter on the motor side and a diode converter on the network side is the solution most widely adopted throughout industry (with more than 50, 000 units installed in France per year). It still remains to be seen whether such a solution could be profitable in wind generator application (since the cost of the drive is quite high). This technical analysis is more destined for the converter-machine assembly specialists and is presented in this document, paying particular attention as it does to the modelling of the `wind energy - generator - drive - network` assembly, the associated drive command and control strategies and the simulations obtained during various transients. A 7.5 kW test bed has been installed in the Laboratoire d`Electronique de Puissance de Clamart, enabling tests to be carried out which emulate the operation of a wind generator.

Speeding driving behaviour: Age and gender experimental analysis

Directory of Open Access Journals (Sweden)

Teo Sir Hiang

2016-01-01

Full Text Available Road safety is a substantial issue worldwide. Speeding contributed to one-third of all the fatal crashes reported from year 2002 to 2011 with young drivers reported to have the highest fatality and injury rates. This paper studied on the speeding driving behavior of 10 teenagers and 10 adults, from both genders. The aim was to investigate the relationship between age and gender with speeding driving behavior. The drivers were required to drive within an enclosed compound by using a test car. Results showed young and male drivers averagely travelled at higher velocity before entering the roundabout and at the same time accelerate to higher velocity upon exiting the roundabout compared to old and female drivers.

Speed-Sensorless DTC-SVM for Matrix Converter Drives With Simple Non-Linearity Compensation

DEFF Research Database (Denmark)

Lee, Kyo-Beum; Blaabjerg, Frede; Yoon, Tae-Woong

2005-01-01

This paper presents a new method to improve sensorless performance of matrix converter drives using a parameter estimation scheme. To improve low-speed sensorless performance, the non-Iinearities of a matrix converter drive such as commutation delays, turn-on and turn-off times of switching devic...... method is applied for high performance induction motor drives using a 3 kW matrix converter system without a speed sensor. Experimental results are shown to illustrate the feasibility of the proposed strategy....

Speed Controlled Belt Conveyors: Drives and Mechanical Considerations

Directory of Open Access Journals (Sweden)

BEBIC, M. Z.

2018-02-01

Full Text Available The paper presents variable speed belt conveyor system where the reference speed is changed in order to achieve improved energy efficiency of operation. The recorded measurements show that belt tension varies within the same limits as under constant speed operation. These results introduce a new insight of the present state of the art in variable speed belt conveyor drives. The system is realized with remote control from the control center on an open pit mine. The structure of the multi-motor drive system of a single conveyor, as well as of the network-based control system distributed among belt conveyor stations and the control center are shown. Speed control of a belt conveyor system is organized to provide better utilization of the available material cross section on the belt and reduced electrical energy consumption of the drive. The experimental results obtained on the system prove that, under existing constraints, the applied algorithm has not introduced additional stress to the belt or mechanical assemblies during acceleration and deceleration processes, while providing higher energy efficiency of operation.

An extended heterogeneous car-following model accounting for anticipation driving behavior and mixed maximum speeds

Science.gov (United States)

Sun, Fengxin; Wang, Jufeng; Cheng, Rongjun; Ge, Hongxia

2018-02-01

The optimal driving speeds of the different vehicles may be different for the same headway. In the optimal velocity function of the optimal velocity (OV) model, the maximum speed vmax is an important parameter determining the optimal driving speed. A vehicle with higher maximum speed is more willing to drive faster than that with lower maximum speed in similar situation. By incorporating the anticipation driving behavior of relative velocity and mixed maximum speeds of different percentages into optimal velocity function, an extended heterogeneous car-following model is presented in this paper. The analytical linear stable condition for this extended heterogeneous traffic model is obtained by using linear stability theory. Numerical simulations are carried out to explore the complex phenomenon resulted from the cooperation between anticipation driving behavior and heterogeneous maximum speeds in the optimal velocity function. The analytical and numerical results all demonstrate that strengthening driver's anticipation effect can improve the stability of heterogeneous traffic flow, and increasing the lowest value in the mixed maximum speeds will result in more instability, but increasing the value or proportion of the part already having higher maximum speed will cause different stabilities at high or low traffic densities.

Multiroller traction drive speed reducer: Evaluation for automotive gas turbine engine

Science.gov (United States)

Rohn, D. A.; Anderson, N. E.; Loewenthal, S. H.

1982-01-01

Tests were conducted on a nominal 14:1 fixed-ratio Nasvytis multiroller traction drive retrofitted as the speed reducer in an automotive gas turbine engine. Power turbine speeds of 45,000 rpm and a drive output power of 102 kW (137 hp) were reached. The drive operated under both variable roller loading (proportional to torque) and fixed roller loading (automatic loading mechanism locked). The drive operated smoothly and efficiently as the engine speed reducer. Engine specific fuel consumption with the traction speed reducer was comparable to that with the original helical gearset.

Decoupled Speed and Torque Control of IPMSM Drives Using a Novel Load Torque Estimator

Directory of Open Access Journals (Sweden)

ZAKY, M.

2017-08-01

Full Text Available This paper proposes decoupled speed and torque control of interior permanent magnet synchronous motor (IPMSM drives using a novel load torque estimator (LTE. The proposed LTE is applied for computing a load torque and yielding a feed-forward value in the speed controller to separate the torque control from the speed control. Indirect flux weakening using direct current component is obtained for high speed operation of the IPMSM drive, and its value for maximum torque per ampere (MTPA control in constant torque region is also used. LTE uses values of direct and quadrature currents to improve the behavior of the speed controller under the reference tracking and torque disturbances. The complete IPMSM drive by Matlab/Simulink is built. The effectiveness of the proposed control scheme using an experimental setup of the complete drive system implemented on a DSP-DS1102 control board is confirmed. Extensive results over a wide speed range are verified. The efficacy of the proposed method is confirmed in comparison to a conventional PI controller under both the reference speed tracking and load torque disturbance.

EVALUATION METHOD OF FUEL-EFFICIENT DRIVING IN DUMP TRUCK USING VEHICLE SPEED AND ENGINE ROTATIONAL SPEED

Science.gov (United States)

Hirata, Masafumi; Yamamoto, Tatsuo; Yasui, Toshiaki; Hayashi, Mayu; Takebe, Atsuji; Funahashi, Masashi

In the construction site, the light oil that the construction vehicle such as dump trucks uses accounts for 70 percent of the amount of the energy use. Therefore, the eco-driving education of the construction vehicle is effective in the fuel cost improvement and the CO2 reduction. The eco-driving education can be executed cheap and easily, and a high effect can be expected. However, it is necessary to evaluate the eco-driving situation of the construction vehicle exactly to maintain the educative effect for a long term. In this paper, the method for evaluating the effect of the fuel cost improvement was examined by using the vehicle speed and the engine rotational speed of the dump truck. In this method, "Ideal eco-driving model" that considers the difference between the vehicle model and the running condition (traffic jam etc.) is made. As a result, it is possible to evaluate the fuel consumption improvement effect of a dump truck by the same index.

Adjustable Speed Drives and Power Quality

DEFF Research Database (Denmark)

Davari, Pooya; Yang, Yongheng; Zare, Firuz

2016-01-01

This paper provides an overview and proposes cost-effective and efficient opportunities in improving power quality in Adjustable Speed Drive (ASD) systems. In particular, an Electronic Inductor (EI) technique has been used in single drives to overcome the existing challenges in conventional...... frontend rectifiers even at partial loading conditions. Moreover, the effectiveness of the EI technique along with a phase-shifted current control in terms of improved grid current quality in multi-drive configurations is addressed. Furthermore, a novel DC-link current modulation scheme for multi...

Global Sensitivity Analysis of High Speed Shaft Subsystem of a Wind Turbine Drive Train

Directory of Open Access Journals (Sweden)

Saeed Asadi

2018-01-01

Full Text Available The wind turbine dynamics are complex and critical area of study for the wind industry. Quantification of the effective factors to wind turbine performance is valuable for making improvements to both power performance and turbine health. In this paper, the global sensitivity analysis of validated mathematical model for high speed shaft drive train test rig has been developed in order to evaluate the contribution of systems input parameters to the specified objective functions. The drive train in this study consists of a 3-phase induction motor, flexible shafts, shafts’ coupling, bearing housing, and disk with an eccentric mass. The governing equations were derived by using the Lagrangian formalism and were solved numerically by Newmark method. The variance based global sensitivity indices are introduced to evaluate the contribution of input structural parameters correlated to the objective functions. The conclusion from the current research provides informative beneficial data in terms of design and optimization of a drive train setup and also can provide better understanding of wind turbine drive train system dynamics with respect to different structural parameters, ultimately designing more efficient drive trains. Finally, the proposed global sensitivity analysis (GSA methodology demonstrates the detectability of faults in different components.

Drivers' perceptions regarding speeding and driving on urban residential streets with a 30 km/h speed limit

Directory of Open Access Journals (Sweden)

Do Duy Dinh

2013-07-01

Full Text Available Previous studies have shown very little information regarding drivers' opinions, attitudes and behaviours with respect to speeding and driving on urban residential streets with a 30 km/h speed limit. The present research aims to address this issue by conducting a questionnaire study with a sample of 367 Japanese drivers. The results showed that drivers tended to have positive beliefs about complying with the 30 km/h speed limit and understand the negative consequences of speeding; however, a majority of the drivers considered breaking the speed limit as a way to reduce their travel time. While the extent of speeding was found to be very serious, a number of drivers still supported the use of a 30 km/h speed limit on residential streets and favoured protecting the right of vulnerable street users. The logistic regression models developed in this study identified that the drivers who did not support the 30 km/h speed limit were associated with those who had committed traffic-law violations, who had negative beliefs about complying with the speed limit, who did not consider residents' opinions, who believed it is acceptable for them to drive at a high speed, and who felt it difficult to refrain from speeding. With regard to anti-speeding countermeasures, under drivers' point of view, streets should be designed to make the 30 km/h speed limit more credible, although this study also showed evidence supporting the application of public awareness programmes and social campaigns as speeding interventions. In addition, this research investigated drivers' speed choices in various specific driving circumstances, and six underlying factors affecting drivers' speed choices were determined. On the basic of the findings, the implications and suggestions for speeding interventions were also discussed.

An analysis on older driver's driving behavior by GPS tracking data: Road selection, left/right turn, and driving speed

Directory of Open Access Journals (Sweden)

Yanning Zhao

2018-02-01

Full Text Available With the high older-related accident ratio and increasing population aging problem, understanding older drivers' driving behaviors has become more and more important for building and improving transportation system. This paper examines older driver's driving behavior which includes road selection, left/right turn and driving speed. A two-month experiment of 108 participants was carried out in Aichi Prefecture, Japan. Since apparently contradictory statements were often drawn in survey-based or simulators-based studies, this study collected not only drivers' basic information but also GPS data. Analysis of road selection demonstrates that older drivers are reluctant to drive on expressway not only in short trips but also in long trips. The present study did not find significant difference between older drivers and others while turning at the intersections. To investigate the impact factors on driving speed, a random-effects regression model is constructed with explanatory variables including age, gender, road types and the interaction terms between age and road types. Compared with other variables, it fails to find that age (60 years old or over has significant impact on driving speed. Moreover, the results reflect that older drivers drive even faster than others at particular road types: national road and ordinary municipal road. The results in this study are expected to help improve transportation planning and develop driving assistance systems for older drivers.

Driving on urban roads: How we come to expect the 'correct' speed.

Science.gov (United States)

Charlton, Samuel G; Starkey, Nicola J

2017-11-01

The subjective categories that drivers use to distinguish between different road types have been shown to influence the speeds they choose to drive but as yet we do not understand the road features that drivers use to make their discriminations. To better understand how drivers describe and categorise the roads they drive, 55 participants were recruited to drive a video of familiar urban roads in a driving simulator at the speed they would drive these roads in their own cars (using the accelerator and brake pedal in the driving simulator to adjust their speed). The participants were then asked to sort photos of the roads they had just driven into piles so that their driving would be the same on all roads in one pile but different to the other piles. Finally, they answered a series of questions about each road to indicate what speed they would drive, the safe speed for the road, their speed limit belief as well as providing ratings of comfort, difficulty and familiarity. Overall, drivers' categorisation of roads was informed by a number of factors including speed limit belief, road features and markings (including medians), road width, and presence of houses, driveways and footpaths. The participants' categories were congruent with what they thought the speed limits were, but not necessarily the actual speed limits. Mismatches between actual speed limits and speed limit beliefs appeared to result from category-level expectations about speed limits that took precedence over recent experience in the simulator. Roads that historically had a 50km/h speed limit but had been reduced to 40km/h were still regarded as 50km/h roads by the participants, underscoring the point that simply posting a sign with a lower speed limit is not enough to overcome drivers' expectations and habits associated with the visual appearance of a road. The findings provided insights into how drivers view and categorise roads, and identify specific areas that could be used to improve speed limit

Grey Wolf based control for speed ripple reduction at low speed operation of PMSM drives.

Science.gov (United States)

Djerioui, Ali; Houari, Azeddine; Ait-Ahmed, Mourad; Benkhoris, Mohamed-Fouad; Chouder, Aissa; Machmoum, Mohamed

2018-03-01

Speed ripple at low speed-high torque operation of Permanent Magnet Synchronous Machine (PMSM) drives is considered as one of the major issues to be treated. The presented work proposes an efficient PMSM speed controller based on Grey Wolf (GW) algorithm to ensure a high-performance control for speed ripple reduction at low speed operation. The main idea of the proposed control algorithm is to propose a specific objective function in order to incorporate the advantage of fast optimization process of the GW optimizer. The role of GW optimizer is to find the optimal input controls that satisfy the speed tracking requirements. The synthesis methodology of the proposed control algorithm is detailed and the feasibility and performances of the proposed speed controller is confirmed by simulation and experimental results. The GW algorithm is a model-free controller and the parameters of its objective function are easy to be tuned. The GW controller is compared to PI one on real test bench. Then, the superiority of the first algorithm is highlighted. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Experimental Performance Evaluation of a High Speed Permanent Magnet Synchronous Motor and Drive for a Flywheel Application at Different Frequencies

Science.gov (United States)

Nagorny, Aleksandr S.; Jansen, Ralph H.; Kankam, M. David

2007-01-01

This paper presents the results of an experimental performance characterization study of a high speed, permanent magnet motor/generator (M/G) and drive applied to a flywheel module. Unlike the conventional electric machine the flywheel M/G is not a separated unit; its stator and rotor are integrated into a flywheel assembly. The M/G rotor is mounted on a flywheel rotor, which is magnetically levitated and sealed within a vacuum chamber during the operation. Thus, it is not possible to test the M/G using direct load measurements with a dynamometer and torque transducer. Accordingly, a new in-situ testing method had to be developed. The paper describes a new flywheel M/G and drive performance evaluation technique, which allows the estimation of the losses, efficiency and power quality of the flywheel high speed permanent magnet M/G, while working in vacuum, over wide frequency and torque ranges. This method does not require any hardware modification nor any special addition to the test rig. This new measurement technique is useful for high-speed applications, when applying an external load is technically difficult.

Development of ultra high speed photographic system using high repetition rate visible laser

International Nuclear Information System (INIS)

Lee, Jong Min; Cha, Byung Hun; Kim, Sung Ho; Kim, Jung Bog; Lim, Chang Hwan; Cha, Hyung Ki; Song, Kyu Seok; Lee, Byung Deok; Rhi, Jong Hoon; Baik, Dae Hyun; Han, Jae Min; Rho, Si Pyo; Lee, Byung Cheol; Jeong, Do Yung; Choi, An Seong; Jeong, Chan Ik; Park, Dae Ung; Jeong, Sung Min; Lee, Sang Kil; Kim, Heon Jun; Jang, Rae gak; Jo, Do Hun; Park, Min Young

1992-12-01

The goal of this project is to develop and commercialize a high speed photographic system equipped with a high repetition rate visible laser. The developed system provides the characteristics of high time resolution and large number of frames. The system consists of 10 W air cooled CVL or a 30 W water cooled CVL, a rotating drum-type high speed camera with the framing rate of 35,000 fps, and a automatic control device. The system has the performance of 10 nsec time resolution, 35,000 fps framing rate, and 250 picture frames. The high speed photographic systems are widely applied to the fields such as high-efficient engine development, high-speed vibration analysis, shock wave propagation study, flow visualization analysis, weapon development, etc. (Author)

High spatio-temporal resolution pollutant measurements of on-board vehicle emissions using ultra-fast response gas analyzers

Directory of Open Access Journals (Sweden)

M. Irwin

2018-06-01

Full Text Available Existing ultra-fast response engine exhaust emissions analyzers have been adapted for on-board vehicle use combined with GPS data. We present, for the first time, how high spatio-temporal resolution data products allow transient features associated with internal combustion engines to be examined in detail during on-road driving. Such data are both useful to examine the circumstances leading to high emissions, and reveals the accurate position of urban air quality hot spots as deposited by the candidate vehicle, useful for source attribution and dispersion modelling. The fast response time of the analyzers, which results in 100 Hz data, makes accurate time-alignment with the vehicle's engine control unit (ECU signals possible. This enables correlation with transient air fuel ratio, engine speed, load, and other engine parameters, which helps to explain the causes of the emissions spikes that portable emissions measurement systems (PEMS and conventional slow response analyzers would miss or smooth out due to mixing within their sampling systems. The data presented is from NO and NOx analyzers, but other fast analyzers (e.g. total hydrocarbons (THC, CO and CO2 can be used similarly. The high levels of NOx pollution associated with accelerating on entry ramps to motorways, driving over speed bumps, accelerating away from traffic lights, are explored in detail. The time-aligned ultra-fast analyzers offer unique insight allowing more accurate quantification and better interpretation of engine and driver activity and the associated emissions impact on local air quality.

Sensorless Speed Control including zero speed of Non Salient PM Synchronous Drives

DEFF Research Database (Denmark)

Rasmussen, Henrik

This paper presents a position sensorless drive of non salient pole PM synchronous motors for all speeds including zero speed. Using adaptive Lyapunov design a new approach for the design of an observer is developed. The resulting scheme leads to a nonlinear full order observer for the motor states...

Sensorless Speed Control including zero speed of Non Salient PM Synchronous Drives

DEFF Research Database (Denmark)

Rasmussen, Henrik

2005-01-01

This paper presents a position sensorless drive of non salient pole PM synchronous motors for all speeds including zero speed. Using adaptive Lyapunov design a new approach for the design of an observer is developed. The resulting scheme leads to a nonlinear full order observer for the motor states...

Sensorless speed Control including Zero Speed on Non Salient PM Synchronous Drives

DEFF Research Database (Denmark)

Rasmussen, Henrik

2006-01-01

This paper presents a position sensorless drive of non salient pole PM synchronous motors for all speeds including zero speed. Using adaptive Lyapunov design a new approach for the design of an observer is developed. The resulting scheme leads to a nonlinear full order observer for the motor states...

Traffic violations in Guangdong Province of China: speeding and drunk driving.

Science.gov (United States)

Zhang, Guangnan; Yau, Kelvin K W; Gong, Xiangpu

2014-03-01

The number of speeding- and drunk driving-related injuries in China surged in the years immediately preceding 2004 and then began to decline. However, the percent decrease in the number of speeding and drunk driving incidents (decrease by 22%) is not proportional to the corresponding percent decrease in number of automobile accident-related injuries (decrease by 47%) from the year 2004 to 2010 (Traffic Management Bureau, Ministry of Public Security, Annual Statistical Reports on Road Traffic Accidents). Earlier studies have established traffic violations as one of the major risks threatening road safety. In this study, we examine in greater detail two important types of traffic violation events, speeding and drunk driving, and attempt to identify significant risk factors associated with these types of traffic violations. Risk factors in several different dimensions, including driver, vehicle, road and environmental factors, are considered. We analyze the speeding (N=11,055) and drunk driving (N=10,035) data for the period 2006-2010 in Guangdong Province, China. These data, obtained from the Guangdong Provincial Security Department, are extracted from the Traffic Management Sector-Specific Incident Case Data Report and are the only comprehensive and official source of traffic accident data in China. Significant risk factors associating with speeding and drunk driving are identified. We find that several factors are associated with a significantly higher probability of both speeding and drunk driving, particularly male drivers, private vehicles, the lack of street lighting at night and poor visibility. The impact of other specific and unique risk factors for either speeding or drunk driving, such as hukou, road type/grades, commercial vehicles, compulsory third party insurance and vehicle safety status, also require particular attention. Legislative or regulatory measures targeting different vehicle types and/or driver groups with respect to the various driver

Using variable speed drives technology to reap rewards of efficient HVAC design

International Nuclear Information System (INIS)

Anon.

1999-01-01

Electric motors are continuously running at full speed with vanes and throttles used to modulate the output, in most HVAC applications. This results in an excessive wastage of electrical energy, and the solution is the variable speed drive, which can save vast amounts of energy in fans, pumps and compressors across the HVAC system. Users of traditional control methods will not benefit from the energy savings that are possible through variable speed drives because the motor speed remains the same, with the result that some, and in some cases most, of the energy drawn will be wasted. Variable speed drives are more efficient because they control output by regulating the motor speed, rather than run the motor at full speed and use restrictions to reduce the flow. Recently, small so-called micro-drives have been launched, cutting the cost for most variable speed operation. Variable speed motors can also introduce new features to the HVAC system. An example of how drives can save money and improve the indoor climate is cited for Heathrow airport. There, the gateroom was earlier controlled by modulating valves in both heater and cooler coils, with two fans that operated continuously at rated speed. This system was very inefficient because the occupancy of the gateroom varied between zero and maximum several times daily. A new system was installed using two AC drives, in which one drive controls the supply air fan and the other the return air fan. The energy savings amounted to 89% during two tests and 77% in a third. A pump installation in the district heating system of Strasbourg, Germany, showed the savings that are possible in pump applications

Dynamic ultra high speed Scheimpflug imaging for assessing corneal biomechanical properties

Directory of Open Access Journals (Sweden)

Renato Ambrósio Jr

2013-04-01

Full Text Available OBJECTIVE: To describe a novel technique for clinical characterization of corneal biomechanics using non-invasive dynamic imaging. METHODS: Corneal deformation response during non contact tonometry (NCT is monitored by ultra-high-speed (UHS photography. The Oculus Corvis ST (Scheimpflug Technology; Wetzlar, Germany has a UHS Scheimpflug camera, taking over 4,300 frames per second and of a single 8mm horizontal slit, for monitoring corneal deformation response to NCT. The metered collimated air pulse or puff has a symmetrical configuration and fixed maximal internal pump pressure of 25 kPa. The bidirectional movement of the cornea in response to the air puff is monitored. RESULTS: Measurement time is 30ms, with 140 frames acquired. Advanced algorithms for edge detection of the front and back corneal contours are applied for every frame. IOP is calculated based on the first applanation moment. Deformation amplitude (DA is determined as the highest displacement of the apex in the highest concavity (HC moment. Applanation length (AL and corneal velocity (CVel are recorded during ingoing and outgoing phases. CONCLUSION: Corneal deformation can be monitored during non contact tonometry. The parameters generated provide clinical in vivo characterization of corneal biomechanical properties in two dimensions, which is relevant for different applications in Ophthalmology.

Reactive Burn Model Calibration for PETN Using Ultra-High-Speed Phase Contrast Imaging

Science.gov (United States)

Johnson, Carl; Ramos, Kyle; Bolme, Cindy; Sanchez, Nathaniel; Barber, John; Montgomery, David

2017-06-01

A 1D reactive burn model (RBM) calibration for a plastic bonded high explosive (HE) requires run-to-detonation data. In PETN (pentaerythritol tetranitrate, 1.65 g/cc) the shock to detonation transition (SDT) is on the order of a few millimeters. This rapid SDT imposes experimental length scales that preclude application of traditional calibration methods such as embedded electromagnetic gauge methods (EEGM) which are very effective when used to study 10 - 20 mm thick HE specimens. In recent work at Argonne National Laboratory's Advanced Photon Source we have obtained run-to-detonation data in PETN using ultra-high-speed dynamic phase contrast imaging (PCI). A reactive burn model calibration valid for 1D shock waves is obtained using density profiles spanning the transition to detonation as opposed to particle velocity profiles from EEGM. Particle swarm optimization (PSO) methods were used to operate the LANL hydrocode FLAG iteratively to refine SURF RBM parameters until a suitable parameter set attained. These methods will be presented along with model validation simulations. The novel method described is generally applicable to `sensitive' energetic materials particularly those with areal densities amenable to radiography.

Development of an ultrasonic linear motor with ultra-positioning capability and four driving feet.

Science.gov (United States)

Zhu, Cong; Chu, Xiangcheng; Yuan, Songmei; Zhong, Zuojin; Zhao, Yanqiang; Gao, Shuning

2016-12-01

This paper presents a novel linear piezoelectric motor which is suitable for rapid ultra-precision positioning. The finite element analysis (FEA) was applied for optimal design and further analysis, then experiments were conducted to investigate its performance. By changing the input signal, the proposed motor was found capable of working in the fast driving mode as well as in the precision positioning mode. When working in the fast driving mode, the motor acts as an ultrasonic motor with maximum no-load speed up to 181.2mm/s and maximum thrust of 1.7N at 200Vp-p. Also, when working in precision positioning mode, the motor can be regarded as a flexible hinge piezoelectric actuator with arbitrary motion in the range of 8μm. The measurable minimum output displacement was found to be 0.08μm, but theoretically, can be even smaller. More importantly, the motor can be quickly and accurately positioned in a large stroke. Copyright © 2016 Elsevier B.V. All rights reserved.

Gate Drive For High Speed, High Power IGBTs

Energy Technology Data Exchange (ETDEWEB)

Nguyen, M.N.; Cassel, R.L.; de Lamare, J.E.; Pappas, G.C.; /SLAC

2007-06-18

A new gate drive for high-voltage, high-power IGBTs has been developed for the SLAC NLC (Next Linear Collider) Solid State Induction Modulator. This paper describes the design and implementation of a driver that allows an IGBT module rated at 800A/3300V to switch up to 3000A at 2200V in 3{micro}S with a rate of current rise of more than 10000A/{micro}S, while still being short circuit protected. Issues regarding fast turn on, high de-saturation voltage detection, and low short circuit peak current will be presented. A novel approach is also used to counter the effect of unequal current sharing between parallel chips inside most high-power IGBT modules. It effectively reduces the collector-emitter peak current, and thus protects the IGBT from being destroyed during soft short circuit conditions at high di/dt.

Gate Drive For High Speed, High Power IGBTs

International Nuclear Information System (INIS)

Nguyen, M.N.; Cassel, R.L.; de Lamare, J.E.; Pappas, G.C.; SLAC

2007-01-01

A new gate drive for high-voltage, high-power IGBTs has been developed for the SLAC NLC (Next Linear Collider) Solid State Induction Modulator. This paper describes the design and implementation of a driver that allows an IGBT module rated at 800A/3300V to switch up to 3000A at 2200V in 3(micro)S with a rate of current rise of more than 10000A/(micro)S, while still being short circuit protected. Issues regarding fast turn on, high de-saturation voltage detection, and low short circuit peak current will be presented. A novel approach is also used to counter the effect of unequal current sharing between parallel chips inside most high-power IGBT modules. It effectively reduces the collector-emitter peak current, and thus protects the IGBT from being destroyed during soft short circuit conditions at high di/dt

Ultra-low-energy wide electron exposure unit

International Nuclear Information System (INIS)

Yonago, Akinobu; Oono, Yukihiko; Tokunaga, Kazutoshi; Kishimoto, Junichi; Wakamoto, Ikuo

2001-01-01

Heat and ultraviolet ray processes are used in surface dryness of paint, surface treatment of construction materials and surface sterilization of food containers. A process using a low-energy wide-area electron beam (EB) has been developed that features high speed and low drive cost. EB processing is not widespread in general industry, however, due to high equipment cost and difficult maintenance. We developed an ultra-low-energy wide-area electron beam exposure unit, the Mitsubishi Wide Electron Exposure Unit (MIWEL) to solve these problems. (author)

High speed motion-picture photography. Instrumentation and application

International Nuclear Information System (INIS)

Bertin-Maghit, G.; Delli, C.; Falgayrettes, M.

1981-01-01

Filming technology at 5,000 frames/second is presented in this paper for the determination of the volume and the expension speed of a gas bubble in water. The high speed 16 mm movie camera, fitted with ultra-wide angle lenses, is placed in front of a side light facing the bubble. Ten 60 ms fast flashes, released in succession, illuminate the bubble [fr

Characterising argon-bomb balloons for high-speed photography

CSIR Research Space (South Africa)

Olivier, M

2013-08-01

Full Text Available A method to optimise the geometry, explosive charge mass and volume of an argon bomb for specific lighting requirements has been proposed. The method is specifically aimed at applications that require photographic diagnostics with ultra-high speed...

Speed-controlled three-phase drives. Drehzahlgeregelte Drehstromantriebe

Energy Technology Data Exchange (ETDEWEB)

Steinmetz, E

1981-01-01

Present semiconductor circuit elements have made it possible to produce frequency converters for speed-controlled three-phase drives from the k'' range to the MW range at low cost. Line-powered frequency converter circuits are already in the standardisation stage while the development trends in the field of speed-controlled frequency converter circuits are not foreseeable as yet. Recent developments in the field of electronics have made the circuits simpler and able to implement an increasing number of functions. There is a trend towards programmable digital control systems with microcomputers. Of the 8 articles in the publication, the contribution by M. Wild and R. Wetzl (Synchronous motors with frequency converters drive boiler feed pumps at Bergkamen power plant) has been entered in the data base as a separate citation.

Interharmonic analysis and mitigation in adjustable speed drives

DEFF Research Database (Denmark)

Soltani, Hamid; Loh, Poh Chiang; Blaabjerg, Frede

2014-01-01

This paper presents the theoretical background and studies on the supply side current interharmonics in a double-stage Adjustable Speed Drive (ASD), when they are initiated by motor current imbalance. Some useful approaches are then proposed to compensate for these interharmonic currents in parti......This paper presents the theoretical background and studies on the supply side current interharmonics in a double-stage Adjustable Speed Drive (ASD), when they are initiated by motor current imbalance. Some useful approaches are then proposed to compensate for these interharmonic currents...... in partially and/or fully controlled ASD, resulting in undistorted grid currents. The simulation studies verify the effectiveness of the proposed schemes....

Speed Regulated Continuous DTC Induction Motor Drive in Field Weakening

Directory of Open Access Journals (Sweden)

MATIC, P.

2011-02-01

Full Text Available The paper describes sensorless speed controlled continuous Direct Torque Control (DTC Induction Motor (IM drive in the field weakening regime. Drive comprises an inner torque loop and an outer speed loop. Torque control is based on Proportional - Integral (PI controller with adaptive Gain Scheduling (GS parameters. The GS PI control provides full DC link voltage utilization and a robust disturbance rejection along with a fast torque response. Outer speed loop has a PI regulator with the gains selected so as to obtain a fast and strictly aperiodic response. Proposed drive fully utilizes the available DC bus voltage. The paper comprises analytical considerations, simulation results, and detailed description of the implementation steps. Experimental verification of the proposed solution is conducted on a fixed point Digital Signal Processor (DSP platform.

Dynamic Eco-Driving Speed Guidance at Signalized Intersections: Multivehicle Driving Simulator Based Experimental Study

Directory of Open Access Journals (Sweden)

Peng Chen

2018-01-01

Full Text Available Variations in vehicle fuel consumption and gas emissions are usually associated with changes in cruise speed and the aggressiveness of drivers’ acceleration/deceleration, especially at traffic signals. In an attempt to enhance vehicle fuel efficiency on arterials, this study developed a dynamic eco-driving speed guidance strategy (DESGS using real-time signal timing and vehicle positioning information in a connected vehicle (CV environment. DESGS mainly aims to optimize the fuel/emission speed profiles for vehicles approaching signalized intersections. An optimization-based rolling horizon and a dynamic programming approach were proposed to track the optimal guided velocity for individual vehicles along the travel segment. In addition, a vehicle specific power (VSP based approach was integrated into DESGS to estimate the fuel consumption and CO2 emissions. To evaluate the effectiveness of the overall strategy, 15 experienced drivers were recruited to participate in interactive speed guidance experiments using multivehicle driving simulators. It was found that compared to vehicles without speed guidance, those with DESGS had a significantly reduced number of stops and approximately 25% less fuel consumption and CO2 emissions.

Extended cage adjustable speed electric motors and drive packages

Science.gov (United States)

Hsu, John S.

1999-01-01

The rotor cage of a motor is extended, a second stator is coupled to this extended rotor cage, and the windings have the same number of poles. The motor torque and speed can be controlled by either injecting energy into or extracting energy out from the rotor cage. The motor produces less harmonics than existing doubly-fed motors. Consequently, a new type of low cost, high efficiency drive is produced.

Very-low-speed variable-structure control of sensorless induction machine drives without signal injection

DEFF Research Database (Denmark)

Lascu, Christian; Boldea, Ion; Blaabjerg, Frede

2005-01-01

A sensorless induction machine drive is presented, in which the principles of variable-structure control and direct torque control (DTC) are combined to ensure high-performance operation in the steady state and under transient conditions. The drive employs a new torque and flux controller......, the "linear and variable-structure control", which realizes accurate and robust control in a wide speed range. Conventional DTC transient merits are preserved, while the steady-state behavior is significantly improved. The full-order state observer is a sliding-mode one, which does not require the rotor speed...

System Design of a Cheetah Robot Toward Ultra-high Speed

OpenAIRE

Mantian Li; Xin Wang; Wei Guo; Pengfei Wang; Lining Sun

2014-01-01

High-speed legged locomotion pushes the limits of the most challenging problems of design and development of the mechanism, also the control and the perception method. The cheetah is an existence proof of concept of what we imitate for high-speed running, and provides us lots of inspiration on design. In this paper, a new model of a cheetah-like robot is developed using anatomical analysis and design. Inspired by a biological neural mechanism, we propose a novel control method for controlling...

Environmentally friendly drive for gas compression applications: enhanced design of high-speed induction motors

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, Karina Velloso; Pradurat, Jean Francois; Mercier, Jean Charles [Institut National Polytechncique, Lorrain (France). Converteam Motors Div.; Truchot, Patrick [Nancy Universite (France). Equipe de Recherche sur les Processus Innovatifs (ERPI)

2008-07-01

Taking into account the key issues faced by gas compressors users, this paper aims to help optimize the choice of the drive equipment as well as the driven equipment, in function of the cost of the whole installation life cycle. The design of the enhanced high-speed induction motor (MGV-Moteuer a Grande Vitesse) represents a technological breakthrough for the industry, it allows the direct coupling to the compressor, without using a gearbox making the system more efficient and reliable. From both micro and macro-economic viewpoints, the high-speed electric driver becomes a more efficient use of natural gas energy resources. This new technology associated with the electric option offers challenging and rewarding work to those responsible for the operation and maintenance of the compressor station. The electric option is not only conceptually viable but has a proven track record that justifies serious consideration as an alternative for reliably powering. Once an operator becomes comfortable with the prospects of motor-driven compression, the analysis of machine options requires only a few new approaches to fairly evaluate the alternatives. The application of this reasoning in projects using compression units is especially opportune, in view of the great variations of operational conditions and environmental issues. (author)

Variable Speed Wind Turbine Based on Multiple Generators Drive-Train Configuration

DEFF Research Database (Denmark)

Deng, Fujin; Chen, Zhe

2010-01-01

A variable speed wind turbine is presented in this paper, where multiple permanent magnet synchronous generators (MPMSGs) drive-train configuration is employed in the wind turbine. A cascaded multilevel converter interface based on the MPMSGs is developed to synthesize a desired high ac sinusoidal...... output voltage, which could be directly connected to the grids. What is more, such arrangement has been made so that the output ac voltage having a selected phase angle difference among the stator windings of multiple generators. A phase angle shift strategy is proposed in this paper, which effectively...... reduce the fluctuation of the electromagnetic torque sum and results in a good performance for the MPMSGs structure. The simulation study is conducted using PSCAD/EMTDC, and the results verify the feasibility of this variable speed wind turbine based on multiple generators drive-train configuration....

Advanced Modular, Multi-Channel, High Speed Fiber Optic Sensing System for Acoustic Emissions Monitoring, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Intelligent Fiber Optic Systems Corporation (IFOS) proposes to prove the feasibility of innovations based on ultra-light-weight, ultra-high-speed, multi-channel,...

Latest trends in variable speed drive systems. ; Application to elevators. Kahensoku drive system no saishin doko. ; Elevator eno oyo

Energy Technology Data Exchange (ETDEWEB)

Inaba, H. (Hitachi, Ltd., Tokyo (Japan))

1992-07-12

The history of the elevator development may be summarized as a challenge to heights of buildings, pursuit of energy saving, and realizing comfort. Transfer of its drive system to the inverter drive system has been nearly completed keeping the pace with advance of electronic technologies. This paper describes control systems of elevators, effects of introducing inverters, and future trends. The inverter system used widely now for standard elevators with a speed lower than 105 m/min consists of a converter to rectify the utility power, a regenerative power consuming circuit to suppress overvoltage in the DC stage, and an inverter to supply power to induction motors. Those elevators exceeding a 120 m/min speed use power regenerating inverter system, with its converter controlled using micro computers according to loads and speeds of motors. The inverter system is particularly marked for having realized energy saving, lower power consumption, lower environmental pollution (from harmonics), comfort and maintainability at high levels. 13 refs., 9 figs.

High-Risk Driving Behaviors among Adolescent Binge-Drinkers

Science.gov (United States)

Marcotte, Thomas D.; Bekman, Nicole M.; Meyer, Rachel A.; Brown, Sandra A.

2013-01-01

Background Binge drinking is common among adolescents. Alcohol use, and binge-drinking in particular, has been associated with neurocognitive deficits as well as risk-taking behaviors, which may contribute to negative driving outcomes among adolescents even while sober. Objectives To examine differences in self-reported driving behaviors between adolescent binge-drinkers and a matched sample of controls, including (a) compliance with graduated licensing laws, (b) high risk driving behaviors, and (c) driving outcomes (crashes, traffic tickets). Methods The present study examined driving behaviors and outcomes in adolescent recent binge drinkers (n=21) and demographically and driving history matched controls (n=17), ages 16-18. Results Binge drinkers more frequently violated graduated licensing laws (e.g., driving late at night), and engaged in more “high risk” driving behaviors, such as speeding and using a cell-phone while driving. Binge drinkers had more traffic tickets, crashes and “near crashes” than the control group. In a multivariate analysis, binge drinker status and speeding were the most robust predictors of a crash. Conclusion Binge drinking teens consistently engage in more dangerous driving behaviors and experience more frequent crashes and traffic tickets. They are also less compliant with preventative restrictions placed on youth while they are learning critical safe driving skills. Scientific Significance These findings highlight a need to examine the contribution of underlying traits (such as sensation seeking) and binge-related cognitive changes to these high-risk driving behaviors, which may assist researchers in establishing alternative prevention and policy efforts targeting this population. PMID:22324748

Modeling and predicting low-speed vehicle emissions as a function of driving kinematics.

Science.gov (United States)

Hao, Lijun; Chen, Wei; Li, Lei; Tan, Jianwei; Wang, Xin; Yin, Hang; Ding, Yan; Ge, Yunshan

2017-05-01

An instantaneous emission model was developed to model and predict the real driving emissions of the low-speed vehicles. The emission database used in the model was measured by using portable emission measurement system (PEMS) under actual traffic conditions in the rural area, and the characteristics of the emission data were determined in relation to the driving kinematics (speed and acceleration) of the low-speed vehicle. The input of the emission model is driving cycle, and the model requires instantaneous vehicle speed and acceleration levels as input variables and uses them to interpolate the pollutant emission rate maps to calculate the transient pollutant emission rates, which will be accumulated to calculate the total emissions released during the whole driving cycle. And the vehicle fuel consumption was determined through the carbon balance method. The model predicted the emissions and fuel consumption of an in-use low-speed vehicle type model, which agreed well with the measured data. Copyright © 2016. Published by Elsevier B.V.

The effects of anti-speeding advertisements on the simulated driving behaviour of young drivers.

Science.gov (United States)

Plant, Bernice R C; Irwin, Julia D; Chekaluk, Eugene

2017-03-01

Recent examinations of road safety communications, including anti-speeding advertisements, have considered the differential effects of positive and negative emotional appeals on driver behaviour. However, empirical evaluations of anti-speeding messages have largely relied on measures of viewers' reported intentions to comply with speed limits and the self-reported driving behaviour of viewers post-exposure, which might not be indicative of the direct effects that these messages have on real-world driving behaviour. The current research constitutes a first empirical evaluation of different real-world anti-speeding advertisements, as measured by their effects on young drivers' speeding behaviour, using a driving simulator. Licensed drivers (N=116) aged 17-25 years completed driving measures prior to, immediately following, and 7-10days after viewing one of four social marketing advertisements. Results indicated that young drivers' average driving speeds were modestly reduced immediately after they viewed an anti-speeding advertisement that depicted social consequences for speeding and employed a positive emotional appeal when compared to an emotion-matched control advertisement; however, this effect was not found for the anti-speeding advertisement depicting a crash. Interestingly, the results based on reported intentions to reduce speeding predicted the opposite pattern of results. However, there was no evidence that the immediate changes to speeding were maintained 7-10days later, and prompts during Phase 2 did not appear to have an effect. The implications of these findings for road safety advertisements targeting young drivers are discussed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Using SHRP 2 naturalistic driving data to assess drivers' speed choice while being engaged in different secondary tasks.

Science.gov (United States)

Schneidereit, Tina; Petzoldt, Tibor; Keinath, Andreas; Krems, Josef F

2017-09-01

The engagement in secondary tasks while driving has been found to result in considerable impairments of driving performance. Texting has especially been suspected to be associated with an increased crash risk. At the same time, there is evidence that drivers use various self-regulating strategies to compensate for the increased demands caused by secondary task engagement. One of the findings reported from multiple studies is a reduction in driving speed. However, most of these studies are of experimental nature and do not let the drivers decide for themselves to (not) engage in the secondary task, and therefore, eliminate other strategies of self-regulation (e.g., postponing the task). The goal of the present analysis was to investigate if secondary task engagement results in speed adjustment also under naturalistic conditions. Our analysis relied on data of the SHRP 2 naturalistic driving study. To minimize the influence of potentially confounding factors on drivers' speed choice, we focused on episodes of free flow driving on interstates/highways. Driving speed was analyzed before, during, and after texting, smoking, eating, and adjusting/monitoring radio or climate control; in a total of 403 episodes. Data show some indication for speed adjustment for texting, especially when driving with high speed. However, the effect sizes were small and behavioral patterns varied considerably between drivers. The engagement in the other tasks did not influence drivers' speed behavior significantly. While drivers might indeed reduce speed slightly to accommodate for secondary task engagement, other forms of adaptation (e.g., strategic decisions) might play a more important role in a natural driving environment. The use of naturalistic driving data to study drivers' self-regulatory behavior at an operational level has proven to be promising. Still, in order to obtain a comprehensive understanding about drivers' self-regulatory behavior, a mixed-method approach is required

Output filters for AC adjustable speed drives

DEFF Research Database (Denmark)

Blaabjerg, Frede; Hanigovszki, Norbert; Landkildehus, Jorn, Jorn

2007-01-01

The standard industrial solution for adjustable speed drives (ASD) is the use of induction motors (IM) fed by voltage-source inverters (VSI). The inverter generates a pulsewidth modulated (PWM) voltage, with dv/dt values of about 6 kV/¿s or even more. In three-leg inverters for three-phase appli...

Robust Adaptive Speed Control of Induction Motor Drives

DEFF Research Database (Denmark)

Bidstrup, N.

, (LS) identification and generalized predictive control (GPC) has been implemented and tested on the CVC drive. Allthough GPC is a robust control method, it was not possible to maintain specified controller performance in the entire operating range. This was the main reason for investigating truly...... adaptive speed control of the CVC drive. A direct truly adaptive speed controller has been implemented. The adaptive controller is a moving Average Self-Tuning Regulator which is abbreviated MASTR throughout the thesis. Two practical implementations of this controller were proposed. They were denoted MASTR...... and measurement noise in general, were the major reasons for the drifting parameters. Two approaches was proposed to robustify MASTR2 against the output noise. The first approach consists of filtering the output. Output filtering had a significant effect in simulations, but the robustness against the output noise...

A digital calibration technique for an ultra high-speed wide-bandwidth folding and interpolating analog-to-digital converter in 0.18-{mu}m CMOS technology

Energy Technology Data Exchange (ETDEWEB)

Yu Jinshan; Zhang Ruitao; Zhang Zhengping; Wang Yonglu; Zhu Can; Zhang Lei; Yu Zhou; Han Yong, E-mail: yujinshan@yeah.net [National Laboratory of Analog IC' s, Chongqing 400060 (China)

2011-01-15

A digital calibration technique for an ultra high-speed folding and interpolating analog-to-digital converter in 0.18-{mu}m CMOS technology is presented. The similar digital calibration techniques are taken for high 3-bit flash converter and low 5-bit folding and interpolating converter, which are based on well-designed calibration reference, calibration DAC and comparators. The spice simulation and the measured results show the ADC produces 5.9 ENOB with calibration disabled and 7.2 ENOB with calibration enabled for high-frequency wide-bandwidth analog input. (semiconductor integrated circuits)

Variable speed drives boost air handler benefits

Energy Technology Data Exchange (ETDEWEB)

Twenty-four separate roof-top air handlers, controlled by variable speed ac motor drives, provide comfort and ventilation for employees at a 500,000 sq. ft. sportswear distribution center in southern Virginia. They were chosen over optional packaged HVAC units because of their flexibility, efficiency, and short payback advantages. The operation of the units is described.

Two wheel speed robust sliding mode control for electric vehicle drive

Directory of Open Access Journals (Sweden)

Abdelfatah Nasri

2008-01-01

Full Text Available Nowadays the uses of electrical power resources are integrated in the modern vehicle motion traction chain so new technologies allow the development of electric vehicles (EV by means of static converters-related electric motors. All mechanical transmission devices are eliminated and vehicle wheel motion can be controlled by means of power electronics. The proposed propulsing system consists of two induction motors (IM that ensure the drive of the two back driving wheels. The proposed control structure-called independent machines- for speed control permit the achievement of an electronic differential. The electronic differential system ensures the robust control of the vehicle behavior on the road. It also allows controlling independently, every driving wheel to turn at different speeds in any curve. This paper presents the study and the sliding mode control strategy of the electric vehicle driving wheels.

Efficiency improvement of variable speed electrical drives for HVAC applications

Energy Technology Data Exchange (ETDEWEB)

Abrahamsen, F.; Blaabjerg, F.; Pedersen, J.K. [Aalborg Univ., Inst. of Energy Technology, Aalborg East (Denmark)

2000-07-01

A large part of the produced electrical energy is consumed by ventilators, pumps and compressors, the so-called HVAC applications. A lot of this energy can be saved by speed control, but even with the large saving obtained alone by introduction of variable speed, it is still essential to optimise the control of the variable speed drive and to optimise the electrical machine with respect to efficiency. Experiments are made with energy optimal induction motor control on a 2.2 kW variable speed pump system. It is demonstrated that 10% of the consumed energy can typically be saved by energy optimal motor control compared with constant V/Hz control. In a comparison of induction motors and permanent magnet synchronous motors for a variable speed pump application it is shown that for 2.2 kW motors an investment in high-efficiency or PM motors are typically paid back within 2.5 years and 7 years respectively. For a 90 kW PM motor the pay-back time would be 24 years. It is today not profitable to use PM motors for variable speed HVAC applications above 2 kW rated motor power. A further study is required to determine this limit in power rating more precisely. (orig.)

High Torque, Direct Drive Electric Motor, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Bear Engineering proposes to develop an innovative high torque, low speed, direct drive motor in order to meet NASA's requirements for such devices. Fundamentally,...

Power-Quality-Oriented Optimization in Multiple Three-Phase Adjustable Speed Drives

DEFF Research Database (Denmark)

Yang, Yongheng; Davari, Pooya; Blaabjerg, Frede

2016-01-01

As an almost standardized configuration, Diode Rectifiers (DRs) and Silicon-Controlled Rectifiers (SCRs) are commonly employed as the front-end topology in three-phase Adjustable Speed Drive (ASD) systems. Features of this ASD configuration include: structural and control simplicity, small volume......, low cost, and high reliability during operation. Yet, DRs and SCRs bring harmonic distortions in the mains and thus lowering the overall efficiency. Power quality standards/rules are thus released. For multiple ASD systems, certain harmonics of the total grid current can be mitigated by phase......-shifting the currents drawn by SCR-fed drives, and thus it is much flexible to reduce the Total Harmonic Distortion (THD) level in such applications. However, the effectiveness of this harmonic mitigation scheme for multiple ASD systems depends on: a) the number of parallel drives, b) the power levels, and c...

High Torque, Direct Drive Electric Motor, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Bear Engineering proposes to advance the development of an innovative high torque, low speed, direct drive motor in order to meet NASA's requirements for such...

ELECTROMECHANICAL TRANSIENT PROCESSES DURING SUPPLY VOLTAGE CHANGING IN THE SYSTEM OF POLYMER INSULATION COVERING OF THE CURRENT-CARRYING CORE OF ULTRA HIGH VOLTAGE CABLES

Directory of Open Access Journals (Sweden)

V. M. Zolotaryov

2018-04-01

Full Text Available Aim. The article is devoted to the analysis of the electromechanical transient processes in a system of three frequency-controlled electric drives based on asynchronous motors that control current-carrying core motion, as well as to the study of the effect of such processes on the modes applying three-layer polymer insulation to the current-carrying core. Technique. The study was conducted based on the concepts of electromechanics, electromagnetic field theory, mathematical physics, mathematical modeling. Results. A mathematical model has been developed to analyze transients in an electromechanical system consisting of three frequency-controlled electric drives providing current-carrying core motion of ultra-high voltage cables in an inclined extrusion line. The coordination of the electromechanical parameters of the system drives has been carried out and the permissible changes in the supply voltage at the limiting mass while moving current-carrying core of ultra-high voltage cables with applied polymer insulation have been estimated. Scientific novelty. For the first time it is determined that with the limiting mass of the current-carrying core, the electromechanical system allows to stabilize the current-carrying core speed with the required accuracy at short-term decreases in the supply voltage by no more than 27 % of its amplitude value. It is also shown that this system is resistant to short-term increases in voltage by 32 % for 0.2 s. Practical significance. Using the developed model, it is possible to calculate the change in the configuration and speed of the slack current-carrying core when applying polymer insulation, depending on the specific mass of the current-carrying core per unit length, its tension at the bottom, the torque of the traction motor and the supply voltage to achieve stable operation of the system and accurate working of the set parameters.

Investigations dealing with variable-speed drives of belt conveyor systems; Untersuchungen an drehzahlstellbaren Antrieben von Gurtbandfoerderanlagen

Energy Technology Data Exchange (ETDEWEB)

Heuvel, B. van den [RWE Power AG, Technikzentrum Tagebaue/Hauptwerkstatt, Versuchsabteilung, Frechen (Germany)

2006-04-15

Safe and faultless operation of belt conveyor systems is a crucial factor in maintaining the availability of interlinked conveying systems employed in mining operations; the use of components with a high efficiency or low energy consumption and energy-conserving plant operation modes allow economic efficiency to be enhanced. With the power increase of single drives to 2500 kW the static design is gaining significance and - with the introduction of variable-speed conveyor drives - particular importance is also to be attached to the proper dynamic design and adjustment of the drive units. Comprehensive measurement and computational studies made of different conveyor drive units in the 900 to 2500 kW power range revealed that excitations of torsional natural frequencies caused by the drives' tooth contact frequencies were the reason for the damage that had occurred; remedial measures were developed the efficacy of which was demonstrated in practice. Moreover, investigations aimed at precautionary damage prevention are described which were performed with newly designed gears prior to the conversion of proven conveyor drives to variable-speed drive units. When designing new gears in the future, we recommend to also investigate them with regard to their dynamic behaviour in the drive train during the design phase by performing appropriate torsional vibration analyses. (orig.)

System Design of a Cheetah Robot Toward Ultra-high Speed

Directory of Open Access Journals (Sweden)

Mantian Li

2014-05-01

Full Text Available High-speed legged locomotion pushes the limits of the most challenging problems of design and development of the mechanism, also the control and the perception method. The cheetah is an existence proof of concept of what we imitate for high-speed running, and provides us lots of inspiration on design. In this paper, a new model of a cheetah-like robot is developed using anatomical analysis and design. Inspired by a biological neural mechanism, we propose a novel control method for controlling the muscles' flexion and extension, and simulations demonstrate good biological properties and leg's trajectory. Next, a cheetah robot prototype is designed and assembled with pneumatic muscles, a musculoskeletal structure, an antagonistic muscle arrangement and a J-type cushioning foot. Finally, experiments of the robot legs swing and kick ground tests demonstrate its natural manner and validate the design of the robot. In the future, we will test the bounding behaviour of a real legged system.

Combined Flux Observer With Signal Injection Enhancement for Wide Speed Range Sensorless Direct Torque Control of IPMSM Drives

DEFF Research Database (Denmark)

Blaabjerg, Frede; Andreescu, G.-D.; Pitic, C.I.

2008-01-01

voltage-current model with PI compensator for low-speed operations. As speed increases, the observer switches gradually to a PI compensated closed-loop voltage model, which is solely used at high speeds. High-frequency rotating-voltage injection with a single D-module bandpass vector filter and a phase......This paper proposes a motion-sensorless control system using direct torque control with space vector modulation for interior permanent magnet synchronous motor (IPMSM) drives, for wide speed range operation, including standstill. A novel stator flux observer with variable structure uses a combined...

Effects of central nervous system drugs on driving: speed variability versus standard deviation of lateral position as outcome measure of the on-the-road driving test.

Science.gov (United States)

Verster, Joris C; Roth, Thomas

2014-01-01

The on-the-road driving test in normal traffic is used to examine the impact of drugs on driving performance. This paper compares the sensitivity of standard deviation of lateral position (SDLP) and SD speed in detecting driving impairment. A literature search was conducted to identify studies applying the on-the-road driving test, examining the effects of anxiolytics, antidepressants, antihistamines, and hypnotics. The proportion of comparisons (treatment versus placebo) where a significant impairment was detected with SDLP and SD speed was compared. About 40% of 53 relevant papers did not report data on SD speed and/or SDLP. After placebo administration, the correlation between SDLP and SD speed was significant but did not explain much variance (r = 0.253, p = 0.0001). A significant correlation was found between ΔSDLP and ΔSD speed (treatment-placebo), explaining 48% of variance. When using SDLP as outcome measure, 67 significant treatment-placebo comparisons were found. Only 17 (25.4%) were significant when SD speed was used as outcome measure. Alternatively, for five treatment-placebo comparisons, a significant difference was found for SD speed but not for SDLP. Standard deviation of lateral position is a more sensitive outcome measure to detect driving impairment than speed variability.

Characterization of Input Current Interharmonics in Adjustable Speed Drives

DEFF Research Database (Denmark)

Soltani, Hamid; Davari, Pooya; Zare, Firuz

2017-01-01

This paper investigates the interharmonic generation process in the input current of double-stage Adjustable Speed Drives (ASDs) based on voltage source inverters and front-end diode rectifiers. The effects of the inverter output-side low order harmonics, caused by implementing the double......-edge symmetrical regularly sampled Space Vector Modulation (SVM) technique, on the input current interharmonic components are presented and discussed. Particular attention is also given to the influence of the asymmetrical regularly sampled modulation technique on the drive input current interharmonics....... The developed theoretical analysis predicts the drive interharmonic frequency locations with respect to the selected sampling strategies. Simulation and experimental results on a 2.5 kW ASD system verify the effectiveness of the theoretical analysis....

Wavelet-fuzzy speed indirect field oriented controller for three-phase AC motor drive – Investigation and implementation

Directory of Open Access Journals (Sweden)

Sanjeevikumar Padmanaban

2016-09-01

Full Text Available Three-phase voltage source inverter driven induction motor is used in many medium- and high-power applications. Precision in speed of the motor play vital role, i.e. popular methods of direct/indirect field-oriented control (FOC are applied. FOC is employed with proportional–integral (P-I or proportional–integral–derivative (P-I-D controllers and they are not adaptive, since gains are fixed at all operating conditions. Therefore, it needs a robust speed controlling in precision for induction motor drive application. This research paper articulates a novel speed control for FOC induction motor drive based on wavelet-fuzzy logic interface system. In specific, the P-I-D controller of IFOC which is actually replaced by the wavelet-fuzzy controller. The speed feedback (error signal is composed of multiple low and high frequency components. Further, these components are decomposed by the discrete wavelet transform and the fuzzy logic controller to generate the scaled gains for the indirect FOC induction motor. Complete model of the proposed ac motor drive is developed with numerical simulation Matlab/Simulink software and tested under different working conditions. For experimental verification, a hardware prototype was implemented and the control algorithm is framed using TMS320F2812 digital signal processor (dsp. Both simulation and hardware results presented in this paper are shown in close agreement and conformity about the suitability for industrial applications.

High-speed nonvolatile CMOS/MNOS RAM

International Nuclear Information System (INIS)

Derbenwick, G.F.; Dodson, W.D.; Sokel, R.J.

1979-01-01

A bulk silicon technology for a high-speed static CMOS/MNOS RAM has been developed. Radiation-hardened, high voltage CMOS circuits have been fabricated for the memory array driving circuits and the enhancement-mode p-channel MNOS memory transistors have been fabricated using a native tunneling oxide with a 45 nm CVD Si 3 N 4 insulator deposited at 750 0 C. Read cycle times less than 350 ns and write cycle times of 1 μs are projected for the final 1Kx1 design. The CMOS circuits provide adequate speed for the write and read cycles and minimize the standby power dissipation. Retention times well in excess of 30 min are projected

Ultra-high temperature direct propulsion

International Nuclear Information System (INIS)

Araj, K.J.; Slovik, G.; Powell, J.R.; Ludewig, H.

1987-01-01

Potential advantages of ultra-high exhaust temperature (3000 K - 4000 K) direct propulsion nuclear rockets are explored. Modifications to the Particle Bed Reactor (PBR) to achieve these temperatures are described. Benefits of ultra-high temperature propulsion are discussed for two missions - orbit transfer (ΔV = 5546 m/s) and interplanetary exploration (ΔV = 20000 m/s). For such missions ultra-high temperatures appear to be worth the additional complexity. Thrust levels are reduced substantially for a given power level, due to the higher enthalpy caused by partial disassociation of the hydrogen propellant. Though technically challenging, it appears potentially feasible to achieve such ultra high temperatures using the PBR

Data-based Speed-limit-respecting Eco-driving System

Czech Academy of Sciences Publication Activity Database

Suzdaleva, Evgenia; Nagy, Ivan

2014-01-01

Roč. 44, č. 1 (2014), s. 253-264 ISSN 0968-090X R&D Projects: GA TA ČR TA01030123 Institutional support: RVO:67985556 Keywords : eco-driving * fuel consumption * recommended speed * recursive estimation * quadratic optimal control * dynamic programming Subject RIV: BC - Control Systems Theory Impact factor: 2.818, year: 2014 http://library.utia.cas.cz/separaty/2014/AS/suzdaleva-0427942.pdf

Ultra-High-Speed Travelling Wave Protection of Transmission Line Using Polarity Comparison Principle Based on Empirical Mode Decomposition

Directory of Open Access Journals (Sweden)

Dong Wang

2015-01-01

Full Text Available The traditional polarity comparison based travelling wave protection, using the initial wave information, is affected by initial fault angle, bus structure, and external fault. And the relationship between the magnitude and polarity of travelling wave is ignored. Because of the protection tripping and malfunction, the further application of this protection principle is affected. Therefore, this paper presents an ultra-high-speed travelling wave protection using integral based polarity comparison principle. After empirical mode decomposition of the original travelling wave, the first-order intrinsic mode function is used as protection object. Based on the relationship between the magnitude and polarity of travelling wave, this paper demonstrates the feasibility of using travelling wave magnitude which contains polar information as direction criterion. And the paper integrates the direction criterion in a period after fault to avoid wave head detection failure. Through PSCAD simulation with the typical 500 kV transmission system, the reliability and sensitivity of travelling wave protection were verified under different factors’ affection.

An Ultra-High Speed Whole Slide Image Viewing System

Directory of Open Access Journals (Sweden)

Yukako Yagi

2012-01-01

Full Text Available Background: One of the goals for a Whole Slide Imaging (WSI system is implementation in the clinical practice of pathology. One of the unresolved problems in accomplishing this goal is the speed of the entire process, i.e., from viewing the slides through making the final diagnosis. Most users are not satisfied with the correct viewing speeds of available systems. We have evaluated a new WSI viewing station and tool that focuses on speed.

High Speed Trimaran (HST) Seatrain Experiments, Model 5714

Science.gov (United States)

2013-12-01

wave absorbing beach at the other. The carriage has electro-hydraulic drive and a regenerative braking system with a maximum carriage speed of 20...Carderock Division To: Commander, Naval Sea Systems Command (PMS3 85) Subj FORWARDING OF REPORT Encl: (1) NSWCCD-80-TR-2013/015, "High Speed Trimaran...and verify the system processes and capability. Your comments will be reviewed and are appreciated. JUDE F. BROWN By direction Copy to: NAVSEA

Arc Shape Characteristics with Ultra-High-Frequency Pulsed Arc Welding

Directory of Open Access Journals (Sweden)

Mingxuan Yang

2017-01-01

Full Text Available Arc plasma possesses a constriction phenomenon with a pulsed current. The constriction is created by the Lorentz force, the radial electromagnetic force during arc welding, which determines the energy distribution of the arc plasma. Welding experiments were carried out with ultra-high-frequency pulsed arc welding (UHFP-AW. Ultra-high-speed camera observations were produced for arc surveillance. Hue-saturation-intensity (HSI image analysis was used to distinguish the regions of the arc plasma that represented the heat energy distribution. The measurement of arc regions indicated that, with an ultra-high-frequency pulsed arc, the constriction was not only within the decreased arc geometry, but also within the constricted arc core region. This can be checked by the ratio of the core region to the total area. The arc core region expanded significantly at 40 kHz at 60 A. A current level of 80 A caused a decrease in the total region of the arc. Meanwhile, the ratio of the core region to the total increased. It can be concluded that arc constriction depends on the increased area of the core region with the pulsed current (>20 kHz.

High speed all optical shear wave imaging optical coherence elastography (Conference Presentation)

Science.gov (United States)

Song, Shaozhen; Hsieh, Bao-Yu; Wei, Wei; Shen, Tueng; O'Donnell, Matthew; Wang, Ruikang K.

2016-03-01

Optical Coherence Elastography (OCE) is a non-invasive testing modality that maps the mechanical property of soft tissues with high sensitivity and spatial resolution using phase-sensitive optical coherence tomography (PhS-OCT). Shear wave OCE (SW-OCE) is a leading technique that relies on the speed of propagating shear waves to provide a quantitative elastography. Previous shear wave imaging OCT techniques are based on repeated M-B scans, which have several drawbacks such as long acquisition time and repeated wave stimulations. Recent developments of Fourier domain mode-locked high-speed swept-source OCT system has enabled enough speed to perform KHz B-scan rate OCT imaging. Here we propose ultra-high speed, single shot shear wave imaging to capture single-shot transient shear wave propagation to perform SW-OCE. The frame rate of shear wave imaging is 16 kHz, at A-line rate of ~1.62 MHz, which allows the detection of high-frequency shear wave of up to 8 kHz. The shear wave is generated photothermal-acoustically, by ultra-violet pulsed laser, which requires no contact to OCE subjects, while launching high frequency shear waves that carries rich localized elasticity information. The image acquisition and processing can be performed at video-rate, which enables real-time 3D elastography. SW-OCE measurements are demonstrated on tissue-mimicking phantoms and porcine ocular tissue. This approach opens up the feasibility to perform real-time 3D SW-OCE in clinical applications, to obtain high-resolution localized quantitative measurement of tissue biomechanical property.

Rotor speed estimation for indirect stator flux oriented induction motor drive based on MRAS scheme

Directory of Open Access Journals (Sweden)

Youssef Agrebi

2007-09-01

Full Text Available In this paper, a conventional indirect stator flux oriented controlled (ISFOC induction motor drive is presented. In order to eliminate the speed sensor, an adaptation algorithm for tuning the rotor speed is proposed. Based on the model reference adaptive system (MRAS scheme, the rotor speed is tuned to obtain an exact ISFOC induction motor drive. The reference and adjustable models, developed in stationary stator reference frame, are used in the MRAS scheme to estimate induction rotor peed from measured terminal voltages and currents. The IP gains speed controller and PI gains current controller are calculated and tuned at each sampling time according to the new estimated rotor speed. The proposed algorithm has been tested by numerical simulation, showing the capability of driving active load; and stability is preserved. Experimental results obtained with a general-purpose 1-kW induction machine are presented showing the effectiveness of the proposed approach in terms of dynamic performance.

Investigation on a Power Coupling Steering System for Dual-Motor Drive Tracked Vehicles Based on Speed Control

Directory of Open Access Journals (Sweden)

Li Zhai

2017-08-01

Full Text Available Double-motor drive tracked vehicles (2MDTV are widely used in the tracked vehicle industry due to the development of electric vehicle drive systems. The aim of this paper is to solve the problem of insufficient propulsion motor torque in low-speed, small-radius steering and insufficient power in high-speed large-radius steering. In order to do this a new type of steering system with a coupling device is designed and a closed-loop control strategy based on speed is adopted to improve the lateral stability of the vehicle. The work done entails modeling and simulating the 2MDTV and the proposed control strategy in RecurDyn and Matlab/Simulink. The simulation results show that the 2MDTV with the coupling device outputs more torque and power in both steering cases compared to the 2MDTV without the coupling device, and the steering stability of the vehicle is improved by using the strategy based on speed.

Ultra-high performance, solid-state, autoradiographic image digitization and analysis system

International Nuclear Information System (INIS)

Lear, J.L.; Pratt, J.P.; Ackermann, R.F.; Plotnick, J.; Rumley, S.

1990-01-01

We developed a Macintosh II-based, charge-coupled device (CCD), image digitization and analysis system for high-speed, high-resolution quantification of autoradiographic image data. A linear CCD array with 3,500 elements was attached to a precision drive assembly and mounted behind a high-uniformity lens. The drive assembly was used to sweep the array perpendicularly to its axis so that an entire 20 x 25-cm autoradiographic image-containing film could be digitized into 256 gray levels at 50-microns resolution in less than 30 sec. The scanner was interfaced to a Macintosh II computer through a specially constructed NuBus circuit board and software was developed for autoradiographic data analysis. The system was evaluated by scanning individual films multiple times, then measuring the variability of the digital data between the different scans. Image data were found to be virtually noise free. The coefficient of variation averaged less than 1%, a value significantly exceeding the accuracy of both high-speed, low-resolution, video camera (VC) systems and low-speed, high-resolution, rotating drum densitometers (RDD). Thus, the CCD scanner-Macintosh computer analysis system offers the advantage over VC systems of the ability to digitize entire films containing many autoradiograms, but with much greater speed and accuracy than achievable with RDD scanners

The new AGV high-speed train; Der neue Hochgeschwindigkeitszug AGV

Energy Technology Data Exchange (ETDEWEB)

Mueller, C.

2008-07-01

On 5th February 2008, Alstom lifted the veil on its new AGV high speed-train. With articulated carriages like the TGV, the AGV has a distributed drive system. Designed for a commercial speed of 360 km/h, the modular architecture of the AGV enables it to be built in a variety of configurations. (orig.)

Ultra high-speed (508 MHz) beam position digital feedback system

International Nuclear Information System (INIS)

Kurokawa, Shin-ichi; Kametani, Masatsugu; Nakayama, Takahide; Moriyama, Kunio.

1997-01-01

The B-Factory which is constructed by National Laboratory for High Energy Physics is the device for elucidating the breakdown of symmetry of matter and antimatter by studying the behavior of B mesons which are generated in large quantity when the electrons and the positrons which are accelerated to light velocity level are collided. In order to maintain electron beam-positron beam bunch circling the ring at light velocity stably, the instability of the coupled bunch must be overcome. For this purpose, the ultrahigh speed beam position digital feedback control system was developed. This system is composed of the high speed input-output substrate using GaAs LSI, the feedback computation substrate using complementary metal oxide semiconductor and the memory mounted on it, and the real time operation device. The development of both substrates and their functions are explained. The real time data collection and the change of computation parameters for specific bunch in the real time operation device have become feasible. The signal transmission characteristics of this system are shown. As the result of the action test of this system, it was confirmed to work normally. (K.I.)

Passive wide spectrum harmonic filter for adjustable speed drives in oil and gas industry

Science.gov (United States)

Al Jaafari, Khaled Ali

Non-linear loads such as variable speed drives constitute the bulky load of oil and gas industry power systems. They are widely used in driving induction and permanent magnet motors for variable speed applications. That is because variable speed drives provide high static and dynamic performance. Moreover, they are known of their high energy efficiency and high motion quality, and high starting torque. However, these non-linear loads are main sources of current and voltage harmonics and lower the quality of electric power system. In fact, it is the six-pulse and twelve-pulse diode and thyristor rectifiers that spoil the AC power line with the dominant harmonics (5th, 7th, 11th). They provide DC voltage to the inverter of the variable speed drives. Typical problems that arise from these harmonics are Harmonic resonances', harmonic losses, interference with electronic equipment, and line voltage distortion at the Point of Common Coupling (PCC). Thus, it is necessary to find efficient, reliable, and economical harmonic filters. The passive filters have definite advantage over active filters in terms of components count, cost and reliability. Reliability and maintenance is a serious issue in drilling rigs which are located in offshore and onshore with extreme operating conditions. Passive filters are tuned to eliminate a certain frequency and therefore there is a need to equip the system with more than one passive filter to eliminate all unwanted frequencies. An alternative solution is Wide Spectrum Harmonic passive filter. The wide spectrum harmonic filters are becoming increasingly popular in these applications and found to overcome some of the limitations of conventional tuned passive filter. The most important feature of wide spectrum harmonic passive filters is that only one capacitor is required to filter a wide range of harmonics. Wide spectrum filter is essentially a low-pass filter for the harmonic at fundamental frequency. It can also be considered as a

Mechanical fault diagnostics for induction motor with variable speed drives using Adaptive Neuro-fuzzy Inference System

Energy Technology Data Exchange (ETDEWEB)

Ye, Z. [Department of Electrical & amp; Computer Engineering, Queen' s University, Kingston, Ont. (Canada K7L 3N6); Sadeghian, A. [Department of Computer Science, Ryerson University, Toronto, Ont. (Canada M5B 2K3); Wu, B. [Department of Electrical & amp; Computer Engineering, Ryerson University, Toronto, Ont. (Canada M5B 2K3)

2006-06-15

A novel online diagnostic algorithm for mechanical faults of electrical machines with variable speed drive systems is presented in this paper. Using Wavelet Packet Decomposition (WPD), a set of feature coefficients, represented with different frequency resolutions, related to the mechanical faults is extracted from the stator current of the induction motors operating over a wide range of speeds. A new integrated diagnostic system for electrical machine mechanical faults is then proposed using multiple Adaptive Neuro-fuzzy Inference Systems (ANFIS). This paper shows that using multiple ANFIS units significantly reduces the scale and complexity of the system and speeds up the training of the network. The diagnostic algorithm is validated on a three-phase induction motor drive system, and it is proven to be capable of detecting rotor bar breakage and air gap eccentricity faults with high accuracy. The algorithm is applicable to a variety of industrial applications where either continuous on-line monitoring or off-line fault diagnostics is required. (author)

Optimization of ultra-low-power CMOS transistors

International Nuclear Information System (INIS)

Stockinger, M.

2000-01-01

Ultra-low-power CMOS integrated circuits have constantly gained importance due to the fast growing portable electronics market. High-performance applications like mobile telephones ask for high-speed computations and low stand-by power consumption to increase the actual operating time. This means that transistors with low leakage currents and high drive currents have to be provided. Common fabrication methods will soon reach their limits if the on-chip feature size of CMOS technology continues to shrink at this very fast rate. New device architectures will help to keep track with the roadmap of the semiconductor industry. Especially doping profiles offer much freedom for performance improvements as they determine the 'inner functioning' of a transistor. In this work automated doping profile optimization is performed on MOS transistors within the TCAD framework SIESTA. The doping between and under the source/drain wells is discretized on an orthogonal optimization grid facilitating almost arbitrary two-dimensional shapes. A linear optimizer issued to find the optimum doping profile by variation of the doping parameters utilizing numerical device simulations with MINIMOS-NT. Gaussian functions are used in further optimization runs to make the doping profiles smooth. Two device generations are considered, one with 0.25 μm, the other with 0.1 μm gate length. The device geometries and source/drain doping profiles are kept fixed during optimization and supply voltages are chosen suitable for ultra-low-power purposes. In a first optimization study the drive current of NMOS transistors is maximized while keeping the leakage current below a limit of 1 pA/μm. This results in peaking channel doping devices (PCD) with narrow doping peaks placed asymmetrically in the channel. Drive current improvements of 45 % and 71 % for the 0.25 μm and 0.1 μm devices, respectively, are achieved compared to uniformly doped devices. The PCD device is studied in detail and explanations for

Artificial intelligence-based speed control of DTC induction motor drives - A comparative study

Energy Technology Data Exchange (ETDEWEB)

Gadoue, S.M.; Giaouris, D.; Finch, J.W. [School of Electrical, Electronic and Computer Engineering, Newcastle University, Newcastle upon Tyne NE1 7RU (United Kingdom)

2009-01-15

The design of the speed controller greatly affects the performance of an electric drive. A common strategy to control an induction machine is to use direct torque control combined with a PI speed controller. These schemes require proper and continuous tuning and therefore adaptive controllers are proposed to replace conventional PI controllers to improve the drive's performance. This paper presents a comparison between four different speed controller design strategies based on artificial intelligence techniques; two are based on tuning of conventional PI controllers, the third makes use of a fuzzy logic controller and the last is based on hybrid fuzzy sliding mode control theory. To provide a numerical comparison between different controllers, a performance index based on speed error is assigned. All methods are applied to the direct torque control scheme and each control strategy has been tested for its robustness and disturbance rejection ability. (author)

Ultra-high density aligned Carbon-nanotube with controled nano-morphology for supercapacitors

Science.gov (United States)

Ghaffari, Mehdi; Zhao, Ran; Liu, Yang; Zhou, Yue; Cheng, Jiping; Guzman de Villoria, Roberto; Wardle, B. L.; Zhang, Q. M.

2012-02-01

Recent advances in fabricating controlled-morphology vertically aligned carbon nanotubes (VA-CNTs) with ultrahigh volume fractioncreate unique opportunities for developing unconventional supercapacitors with ultra-high energy density, power density, and long charge/discharge cycle life.Continuous paths through inter-VA-CNT channels allow fast ion transport, and high electrical conduction of the aligned CNTs in the composite electrodes lead to fast discharge speed. We investigate the charge-discharge characteristics of VA-CNTs with >20 vol% of CNT and ionic liquids as electrolytes. By employing both the electric and electromechanical spectroscopes, as well as nanostructured materials characterization, the ion transport and storage behaviors in porous electrodes are studied. The results suggest pathways for optimizing the electrode morphology in supercapacitorsusing ultra-high volume fraction VA-CNTs to further enhance performance.

The Enright phenomenon. Stereoscopic distortion of perceived driving speed induced by monocular pupil dilation.

Science.gov (United States)

Carkeet, Andrew; Wood, Joanne M; McNeill, Kylie M; McNeill, Hamish J; James, Joanna A; Holder, Leigh S

The Enright phenomenon describes the distortion in speed perception experienced by an observer looking sideways from a moving vehicle when viewing with interocular differences in retinal image brightness, usually induced by neutral density filters. We investigated whether the Enright phenomenon could be induced with monocular pupil dilation using tropicamide. We tested 17 visually normal young adults on a closed road driving circuit. Participants were asked to travel at Goal Speeds of 40km/h and 60km/h while looking sideways from the vehicle with: (i) both eyes with undilated pupils; (ii) both eyes with dilated pupils; (iii) with the leading eye only dilated; and (iv) the trailing eye only dilated. For each condition we recorded actual driving speed. With the pupil of the leading eye dilated participants drove significantly faster (by an average of 3.8km/h) than with both eyes dilated (p=0.02); with the trailing eye dilated participants drove significantly slower (by an average of 3.2km/h) than with both eyes dilated (p<0.001). The speed, with the leading eye dilated, was faster by an average of 7km/h than with the trailing eye dilated (p<0.001). There was no significant difference between driving speeds when viewing with both eyes either dilated or undilated (p=0.322). Our results are the first to show a measurable change in driving behaviour following monocular pupil dilation and support predictions based on the Enright phenomenon. Copyright © 2016 Spanish General Council of Optometry. Published by Elsevier España, S.L.U. All rights reserved.

Design of a high speed rotating mechanical shutter

International Nuclear Information System (INIS)

Stowers, I.F.; Merritt, B.T.; McFann, C.B.

1979-01-01

A high-speed rotating shutter was designed to operate in a 10 -6 Torr vacuum at the optical focus of a laser spatial filter. The shutter is basically a wheel, with a single 3 x 10-mm slot at the perimeter, which rotates with a peripheral speed of 1 km/s. The motor to drive the rotating wheel is magnetically suspended and synchronously wound. The wheel achieves a 4 μs opening time and a timing accuracy of better than 0.2 μs

Fall from a car driving at high speed: A case report.

Science.gov (United States)

Maujean, Géraldine; Guinet, Tiphaine; Malicier, Daniel

2016-04-01

In cases of falls, the key issue for forensic scientists is to determine the manner of death. They must distinguish between accidental falls, suicidal falls, falls including blows and falls caused by a blow. Several strategies have been proposed in the literature to help explain injury patterns. Here, we report an original case of a man who died after jumping from a car moving at high speed. A mathematical and modeling approach was developed to reconstruct the trajectory of the body in order to understand the injury pattern and apparent discrepancy between the high speed of the car from which the victim jumped and the topography of the bone fractures, which were limited to the skull. To define the initial values of the model's parameters, a technical vehicle evaluation and several test jumps at low speed were carried out. We studied in greater detail the trajectory of three characteristic points corresponding to the dummy's center of gravity, head and right foot. Calculations were made with and without the air friction effect to show its influence. Finally, we were successful in modeling the initial trajectory of the body and the variation of its head energy over time, which were consistent with the injuries observed. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Influences of Cutting Speed and Material Mechanical Properties on Chip Deformation and Fracture during High-Speed Cutting of Inconel 718

Directory of Open Access Journals (Sweden)

Bing Wang

2018-03-01

Full Text Available The paper aims to investigate the influences of material constitutive and fracture parameters in addition to cutting speed on chip formation during high-speed cutting of Inconel 718. Finite element analyses for chip formation are conducted with Johnson–Cook constitutive and fracture models. Meanwhile, experiments of high-speed orthogonal cutting are performed to verify the simulation results with cutting speeds ranging from 50 m/min to 7000 m/min. The research indicates that the chip morphology transforms from serrated to fragmented at the cutting speed of 7000 m/min due to embrittlement of the workpiece material under ultra-high cutting speeds. The parameter of shear localization sensitivity is put forward to describe the influences of material mechanical properties on serrated chip formation. The results demonstrate that the effects of initial yield stress and thermal softening coefficient on chip shear localization are much more remarkable than the other constitutive parameters. For the material fracture parameters, the effects of initial fracture strain and exponential factor of stress state on chip shear localization are more much prominent. This paper provides guidance for controlling chip formation through the adjustment of material mechanical properties and the selection of appropriate cutting parameters.

Influences of Cutting Speed and Material Mechanical Properties on Chip Deformation and Fracture during High-Speed Cutting of Inconel 718.

Science.gov (United States)

Wang, Bing; Liu, Zhanqiang; Hou, Xin; Zhao, Jinfu

2018-03-21

The paper aims to investigate the influences of material constitutive and fracture parameters in addition to cutting speed on chip formation during high-speed cutting of Inconel 718. Finite element analyses for chip formation are conducted with Johnson-Cook constitutive and fracture models. Meanwhile, experiments of high-speed orthogonal cutting are performed to verify the simulation results with cutting speeds ranging from 50 m/min to 7000 m/min. The research indicates that the chip morphology transforms from serrated to fragmented at the cutting speed of 7000 m/min due to embrittlement of the workpiece material under ultra-high cutting speeds. The parameter of shear localization sensitivity is put forward to describe the influences of material mechanical properties on serrated chip formation. The results demonstrate that the effects of initial yield stress and thermal softening coefficient on chip shear localization are much more remarkable than the other constitutive parameters. For the material fracture parameters, the effects of initial fracture strain and exponential factor of stress state on chip shear localization are more much prominent. This paper provides guidance for controlling chip formation through the adjustment of material mechanical properties and the selection of appropriate cutting parameters.

High power CO2 laser development with AOM integration for ultra high-speed pulses

Science.gov (United States)

Bohrer, Markus; Vaupel, Matthias; Nirnberger, Robert; Weinberger, Bernhard; Jamalieh, Murad

2017-01-01

There is a 500 billion USD world market for packaging expected to grow to a trillion in 2030. Austria plays an important role world wide for high speed laser engraving applications — especially when it comes to high end solutions. Such high end solutions are fundamental for the production of print forms for the packaging and decorating industry (e. g. cans). They are additionally used for security applications (e. g. for printing banknotes), for the textile printing industry and for creating embossing forms (e. g. for the production of dashboards in the automotive industry). High speed, high precision laser engraving needs laser resonators with very stable laser beams (400 - 800W) especially in combination with AOMs. Based upon a unique carbon fiber structure - stable within the sub-micrometer range - a new resonator has been developed, accompanied by most recent thermo-mechanical FEM calculations. The resulting beam is evaluated on an automated optical bench using hexapods, allowing to optimize the complete beam path with collimators and AOM. The major steps related to laser engraving of dry offset printing plates during the full workflow from the artists design to the printed result on an aluminum can is presented in this paper as well as laser characteristics, AOM integration and correlative CLSM and SEM investigation of the results.

An Analysis of an Ultra-High Speed Content-Addressable Database Retrieval System

National Research Council Canada - National Science Library

Costianes, Peter

2001-01-01

...) and its implementation as a high speed optical chip. The paradigm uses polarization states to represent binary very words and EO modulators to represent database words to perform what is essentially XOR operations...

Possibilities of rotating drums in ultra-high-speed cinematography

International Nuclear Information System (INIS)

Andre, Michel

A theoretical study shows that it is possible to produce a drum rotating at a peripheral speed of 500m/s. A prototype has actually reached this speed and confirmed the feasibility of the system. It is driven by an electric motor and is made of titanium covered with boron fibres. The main performances to be expected of cameras (whole-image, slit or spectrographic) using such a drum is described [fr

Effects of Pay-As-You-Drive vehicle insurance on young drivers' speed choice : Results of a Dutch field experiment

NARCIS (Netherlands)

Bolderdijk, J.W.; Knockaert, J.; Steg, L.; Verhoef, E.T.

Speeding is an important cause for young drivers' involvement in traffic accidents. A reduction in driving speeds of this group could result in fewer accidents. One way of reducing driving speed is offering explicit financial incentives. In collaboration with five Dutch car insurance companies, we

Synthesis of ultra-thin tellurium nanoflakes on textiles for high-performance flexible and wearable nanogenerators

Energy Technology Data Exchange (ETDEWEB)

He, Wen; Van Ngoc, Huynh; Qian, Yong Teng; Hwang, Jae Seok; Yan, Ya Ping [Department of Physics and Interdisciplinary Course of Physics and Chemistry, Sungkyunkwan University, 2066, Seobu-ro, Jangan-gu, Suwon 16419, Gyeoggi-do (Korea, Republic of); Choi, Hongsoo [Department of Robotics Engineering, Daegu Gyeongbuk Institute of Science and Technology (DGIST), 711-873, Daegu (Korea, Republic of); Kang, Dae Joon, E-mail: djkang@skku.edu [Department of Physics and Interdisciplinary Course of Physics and Chemistry, Sungkyunkwan University, 2066, Seobu-ro, Jangan-gu, Suwon 16419, Gyeoggi-do (Korea, Republic of)

2017-01-15

Highlights: • Ultra-thin tellurium (Te) nanoflakes were successfully grown on textile and used as an active piezoelectric material. • Te nanoflake nanogenerator device was systematically studied by bending and compressing test. • The ultra-high output power during compressing test can light up 10 LEDs without any external power source. • The device can offer a breakthrough in applying tellurium nanoflakes into high-performance flexible and wearable piezoelectric nanogenerator. - Abstract: We report that ultra-thin tellurium (Te) nanoflakes were successfully grown on a sample of a gold-coated textile, which then was used as an active piezoelectric material. An output voltage of 4 V and a current of 300 nA were obtained from the bending test under a driving frequency of 10 Hz. To test the practical applications, Te nanoflake nanogenerator (TFNG) device was attached to the subject’s arm, and mechanical energy was converted to electrical energy by means of periodic arm-bending motions. The optimized open-circuit voltage and short-circuit current density of approximately 125 V and 17 μA/cm{sup 2}, respectively, were observed when a TFNG device underwent a compression test with a compressive force of 8 N and driving frequency of 10 Hz. This high-power generation enabled the instantaneous powering of 10 green light-emitting diodes that shone without any assistance from an external power source.

Induction motor IFOC based speed-controlled drive with asymptotic disturbance compensation

Directory of Open Access Journals (Sweden)

Stojić Đorđe M.

2012-01-01

Full Text Available This paper presents the design of digitally controlled speed electrical drive, with the asymptotic compensation of external disturbances, implemented by using the IFOC (Indirect Field Oriented Control torque controlled induction motor. The asymptotic disturbance compensation is achieved by using the DOB (Disturbance Observer with the IMP (Internal Model Principle. When compared to the existing IMP-based DOB solutions, in this paper the robust stability and disturbance compensation are improved by implementing the minimal order DOB filter. Also, the IMP-based DOB design is improved by employing the asymptotic compensation of all elemental or more complex external disturbances. The dynamic model of the IFOC torque electrical drive is, also, included in the speed-controller and DOB section design. The simulation and experimental measurements presented in the paper illustrate the effectiveness and robustness of the proposed control scheme.

Modeling and Speed Control of Induction Motor Drives Using Neural Networks

Directory of Open Access Journals (Sweden)

V. Jamuna

2010-08-01

Full Text Available Speed control of induction motor drives using neural networks is presented. The mathematical model of single phase induction motor is developed. A new simulink model for a neural network-controlled bidirectional chopper fed single phase induction motor is proposed. Under normal operation, the true drive parameters are real-time identified and they are converted into the controller parameters through multilayer forward computation by neural networks. Comparative study has been made between the conventional and neural network controllers. It is observed that the neural network controlled drive system has better dynamic performance, reduced overshoot and faster transient response than the conventional controlled system.

No speed limits in medical imaging and high-energy physics

CERN Multimedia

Rita Giuffredi & Tom Meyer

2015-01-01

Speed, or high time resolution, is becoming increasingly important, if not crucial, in the high-energy physics domain, both for particle acceleration and detection systems. Medical-imaging technology also vitally depends on high time resolution detection techniques, often the offspring of today’s large particle physics experiments. The four-year FP7 Marie Curie Training Project “PicoSEC-MCNet”, which draws to a close at the end of November, was designed to develop ultra-fast photon detectors for applications in both domains. The project has achieved important results that promise to trigger further developments in the years to come.   The PicoSEC-MCNet project participants. “New requirements in high-energy physics force us to push the limits of photon detection speed, as future high-luminosity accelerators will force us to cope with the unprecedentedly short bunch crossing intervals needed to produce sufficient luminosity,” explains Tom M...

Mechanical-plowing-based high-speed patterning on hard material via advanced-control and ultrasonic probe vibration

Energy Technology Data Exchange (ETDEWEB)

Wang, Zhihua; Zou, Qingze, E-mail: qzzou@rci.rutgers.edu [Mechanical and Aerospace Engineering Department, Rutgers, the State University of New Jersey, Piscataway, New Jersey 08854 (United States); Tan, Jun; Jiang, Wei [Electrical and Computer Engineering Department, Rutgers, the State University of New Jersey, Piscataway, New Jersey 08854 (United States)

2013-11-15

In this paper, we present a high-speed direct pattern fabrication on hard materials (e.g., a tungsten-coated quartz substrate) via mechanical plowing. Compared to other probe-based nanolithography techniques based on chemical- and/or physical-reactions (e.g., the Dip-pen technique), mechanical plowing is meritorious for its low cost, ease of process control, and capability of working with a wide variety of materials beyond conductive and/or soft materials. However, direct patterning on hard material faces two daunting challenges. First, the patterning throughput is ultimately hindered by the “writing” (plowing) speed, which, in turn, is limited by the adverse effects that can be excited/induced during high-speed, and/or large-range plowing, including the vibrational dynamics of the actuation system (the piezoelectric actuator, the cantilever, and the mechanical fixture connecting the cantilever to the actuator), the dynamic cross-axis coupling between different axes of motion, and the hysteresis and the drift effects related to the piezoelectric actuators. Secondly, it is very challenging to directly pattern on ultra-hard materials via plowing. Even with a diamond probe, the line depth of the pattern via continuous plowing on ultra-hard materials such as tungsten, is still rather small (<0.5 nm), particularly when the “writing” speed becomes high. To overcome these two challenges, we propose to utilize a novel iterative learning control technique to achieve precision tracking of the desired pattern during high-speed, large-range plowing, and introduce ultrasonic vibration of the probe in the normal (vertical) direction during the plowing process to enable direct patterning on ultra hard materials. The proposed approach was implemented to directly fabricate patterns on a mask with tungsten coating and quartz substrate. The experimental results demonstrated that a large-size pattern of four grooves (20 μm in length with 300 nm spacing between lines) can be

Effectiveness of enforcement levels of speed limit and drink driving laws and associated factors – Exploratory empirical analysis using a bivariate ordered probit model

Directory of Open Access Journals (Sweden)

Behram Wali

2017-06-01

Full Text Available The contemporary traffic safety research comprises little information on quantifying the simultaneous association between drink driving and speeding among fatally injured drivers. Potential correlation between driver's drink driving and speeding behavior poses a substantial methodological concern which needs investigation. This study therefore focused on investigating the simultaneous impact of socioeconomic factors, fatalities, vehicle ownership, health services and highway agency road safety policies on enforcement levels of speed limit and drink driving laws. The effectiveness of enforcement levels of speed limit and drink driving laws has been investigated through development of bivariate ordered probit model using data extricated from WHO's global status report on road safety in 2013. The consistent and intuitive parameter estimates along with statistically significant correlation between response outcomes validates the statistical supremacy of bivariate ordered probit model. The results revealed that fatalities per thousand registered vehicles, hospital beds per hundred thousand population and road safety policies are associated with a likely medium or high effectiveness of enforcement levels of speed limit and drink driving laws, respectively. Also, the model encapsulates the effect of several other agency related variables and socio-economic status on the response outcomes. Marginal effects are reported for analyzing the impact of such factors on intermediate categories of response outcomes. The results of this study are expected to provide necessary insights to elemental enforcement programs. Also, marginal effects of explanatory variables may provide useful directions for formulating effective policy countermeasures for overcoming driver's speeding and drink driving behavior.

Variable speed electrical driving systems; Entrainements electriques a vitesse variable

Energy Technology Data Exchange (ETDEWEB)

Bonal, J. [ESE, Promethee, Groupe Schneider (France)

1997-12-31

This book is the first of a series of 3 volumes which synthesize the most recent knowledge on variable speed electrical driving systems. It is devoted to electronic and electromechanical engineers and technicians and to manufacturers of electrical equipments involving such systems. after a recall of basic electrotechnical and mechanical notions, this book focusses on the functionalities and criteria of definition of driving systems, and shows the interactions between the different parts of these equipments. It develops a methodological approach of the choice for the most suitable technology with respect to the application under consideration. Various industrial sectors are concerned and a particular attention is paid to the driving of receptive turbo-machineries which play a major role in the energy balance sheet of the industrial electrical power force. (J.S.) 28 refs.

Novel Observer Scheme of Fuzzy-MRAS Sensorless Speed Control of Induction Motor Drive

Science.gov (United States)

Chekroun, S.; Zerikat, M.; Mechernene, A.; Benharir, N.

2017-01-01

This paper presents a novel approach Fuzzy-MRAS conception for robust accurate tracking of induction motor drive operating in a high-performance drives environment. Of the different methods for sensorless control of induction motor drive the model reference adaptive system (MRAS) finds lot of attention due to its good performance. The analysis of the sensorless vector control system using MRAS is presented and the resistance parameters variations and speed observer using new Fuzzy Self-Tuning adaptive IP Controller is proposed. In fact, fuzzy logic is reminiscent of human thinking processes and natural language enabling decisions to be made based on vague information. The present approach helps to achieve a good dynamic response, disturbance rejection and low to plant parameter variations of the induction motor. In order to verify the performances of the proposed observer and control algorithms and to test behaviour of the controlled system, numerical simulation is achieved. Simulation results are presented and discussed to shown the validity and the performance of the proposed observer.

The Technique of Changing the Drive Method of Micro Step Drive and Sensorless Drive for Hybrid Stepping Motor

Science.gov (United States)

Yoneda, Makoto; Dohmeki, Hideo

The position control system with the advantage large torque, low vibration, and high resolution can be obtained by the constant current micro step drive applied to hybrid stepping motor. However loss is large, in order not to be concerned with load torque but to control current uniformly. As the one technique of a position control system in which high efficiency is realizable, the same sensorless control as a permanent magnet motor is effective. But, it was the purpose that the control method proposed until now controls speed. Then, this paper proposed changing the drive method of micro step drive and sensorless drive. The change of the drive method was verified from the simulation and the experiment. On no load, it was checked not producing change of a large speed at the time of a change by making electrical angle and carrying out zero reset of the integrator. On load, it was checked that a large speed change arose. The proposed system could change drive method by setting up the initial value of an integrator using the estimated result, without producing speed change. With this technique, the low loss position control system, which employed the advantage of the hybrid stepping motor, has been built.

Application of drive circuit based on L298N in direct current motor speed control system

Science.gov (United States)

Yin, Liuliu; Wang, Fang; Han, Sen; Li, Yuchen; Sun, Hao; Lu, Qingjie; Yang, Cheng; Wang, Quanzhao

2016-10-01

In the experiment of researching the nanometer laser interferometer, our design of laser interferometer circuit system is up to the wireless communication technique of the 802.15.4 IEEE standard, and we use the RF TI provided by Basic to receive the data on speed control system software. The system's hardware is connected with control module and the DC motor. However, in the experiment, we found that single chip microcomputer control module is very difficult to drive the DC motor directly. The reason is that the DC motor's starting and braking current is larger than the causing current of the single chip microcomputer control module. In order to solve this problem, we add a driving module that control board can transmit PWM wave signal through I/O port to drive the DC motor, the driving circuit board can come true the function of the DC motor's positive and reversal rotation and speed adjustment. In many various driving module, the L298N module's integrated level is higher compared with other driver module. The L298N model is easy to control, it not only can control the DC motor, but also achieve motor speed control by modulating PWM wave that the control panel output. It also has the over-current protection function, when the motor lock, the L298N model can protect circuit and motor. So we use the driver module based on L298N to drive the DC motor. It is concluded that the L298N driver circuit module plays a very important role in the process of driving the DC motor in the DC motor speed control system.

Proceedings of the 17th international congress on high speed photography and photonics. v. 1-2

International Nuclear Information System (INIS)

McDowell, M.W.; Hollingworth, D.

1986-01-01

One of the unique features of this Congress, is that it provides a forum for practitioners from the host country to describe local and unique applications of high speed photography, fifty percent of the papers were presented by local scientists and engineers. The high proportion of contributions relating to the mining industry emphasises South Africa's leading role in this field. One of the objectives of this congress was to introduce the techniques and applications of high speed photography. Topics covered include: mining applications; ballistics, shockwave and detonation studies; laser studies; x-ray applications; image intensifiers; biomechanics; high and ultra high speed applications; holography; schlieren and interferometry; plasma studies; data analysis techniques and diagnostics; and videography

An EMC Evaluation of the Use of Unshielded Motor Cables in AC Adjustable Speed Drive Applications

DEFF Research Database (Denmark)

Hanigovszki, Norbert; Poulsen, J.; Spiazzi, G.

2004-01-01

The most common solution for modern adjustable speed drives (ASD) is the use of induction motors (IM) fed by voltage-source inverters (VSI). The inverter generates a pulsewidth modulated (PWM) voltage, with values of about 6 kV/ dv/dt m s or even more. In three-leg inverters for three-phase appli......The most common solution for modern adjustable speed drives (ASD) is the use of induction motors (IM) fed by voltage-source inverters (VSI). The inverter generates a pulsewidth modulated (PWM) voltage, with values of about 6 kV/ dv/dt m s or even more. In three-leg inverters for three......-phase applications the occurrence of common-mode voltage is inherent due to asymmetrical output pulses. As a result, for electromagnetic compatibility (EMC) reasons, in most applications shielded cables are used between the inverter and the motor, implying high installation costs. The present paper discusses the use...

Ultra-high-speed wavelength conversion in a silicon photonic chip

DEFF Research Database (Denmark)

Hu, Hao; Ji, Hua; Galili, Michael

2011-01-01

We have successfully demonstrated all-optical wavelength conversion of a 640-Gbit/s line-rate return-to-zero differential phase-shift keying (RZ-DPSK) signal based on low-power four wave mixing (FWM) in a silicon photonic chip with a switching energy of only ~110 fJ/bit. The waveguide dispersion...... of the silicon nanowire is nano-engineered to optimize phase matching for FWM and the switching power used for the signal processing is low enough to reduce nonlinear absorption from twophoton- absorption (TPA). These results demonstrate that high-speed wavelength conversion is achievable in silicon chips...

LC-filter Resonance Cancellation with DPWM Inverters in Adjustable Speed Drives

DEFF Research Database (Denmark)

Vadstrup, Casper; Wang, Xiongfei; Blaabjerg, Frede

2015-01-01

Discontinuous PWM methods cannot easily be used in LC-filtered inverters for adjustable speed drives, as it causes resonances in the filter. This paper present a new method to cancel the resonance and compares this method to previously proposed methods. Wide band gap devices are entering the market...

High speed all optical logic gates based on quantum dot semiconductor optical amplifiers.

Science.gov (United States)

Ma, Shaozhen; Chen, Zhe; Sun, Hongzhi; Dutta, Niloy K

2010-03-29

A scheme to realize all-optical Boolean logic functions AND, XOR and NOT using semiconductor optical amplifiers with quantum-dot active layers is studied. nonlinear dynamics including carrier heating and spectral hole-burning are taken into account together with the rate equations scheme. Results show with QD excited state and wetting layer serving as dual-reservoir of carriers, as well as the ultra fast carrier relaxation of the QD device, this scheme is suitable for high speed Boolean logic operations. Logic operation can be carried out up to speed of 250 Gb/s.

Photon-trapping micro/nanostructures for high linearity in ultra-fast photodiodes

Science.gov (United States)

Cansizoglu, Hilal; Gao, Yang; Perez, Cesar Bartolo; Ghandiparsi, Soroush; Ponizovskaya Devine, Ekaterina; Cansizoglu, Mehmet F.; Yamada, Toshishige; Elrefaie, Aly F.; Wang, Shih-Yuan; Islam, M. Saif

2017-08-01

Photodetectors (PDs) in datacom and computer networks where the link length is up to 300 m, need to handle higher than typical input power used in other communication links. Also, to reduce power consumption due to equalization at high speed (>25Gb/s), the datacom links will use PAM-4 signaling instead of NRZ with stringent receiver linearity requirements. Si PDs with photon-trapping micro/nanostructures are shown to have high linearity in output current verses input optical power. Though there is less silicon material due to the holes, the micro-/nanostructured holes collectively reradiate the light to an in-plane direction of the PD surface and can avoid current crowding in the PD. Consequently, the photocurrent per unit volume remains at a low level contributing to high linearity in the photocurrent. We present the effect of design and lattice patterns of micro/nanostructures on the linearity of ultra-fast silicon PDs designed for high speed multi gigabit data networks.

Multi-level storage and ultra-high speed of superlattice-like Ge50Te50/Ge8Sb92 thin film for phase-change memory application.

Science.gov (United States)

Wu, Weihua; Chen, Shiyu; Zhai, Jiwei; Liu, Xinyi; Lai, Tianshu; Song, Sannian; Song, Zhitang

2017-10-06

Superlattice-like Ge 50 Te 50 /Ge 8 Sb 92 (SLL GT/GS) thin film was systematically investigated for multi-level storage and ultra-fast switching phase-change memory application. In situ resistance measurement indicates that SLL GT/GS thin film exhibits two distinct resistance steps with elevated temperature. The thermal stability of the amorphous state and intermediate state were evaluated with the Kissinger and Arrhenius plots. The phase-structure evolution revealed that the amorphous SLL GT/GS thin film crystallized into rhombohedral Sb phase first, then the rhombohedral GeTe phase. The microstructure, layered structure, and interface stability of SLL GT/GS thin film was confirmed by using transmission electron microscopy. The transition speed of crystallization and amorphization was measured by the picosecond laser pump-probe system. The volume variation during the crystallization was obtained from x-ray reflectivity. Phase-change memory (PCM) cells based on SLL GT/GS thin film were fabricated to verify the multi-level switching under an electrical pulse as short as 30 ns. These results illustrate that the SLL GT/GS thin film has great potentiality in high-density and high-speed PCM applications.

Ultra high energy gamma-ray astronomy

International Nuclear Information System (INIS)

Wdowczyk, J.

1986-01-01

The experimental data on ultra high energy γ-rays are reviewed and a comparison of the properties of photon and proton initiated shower is made. The consequences of the existence of the strong ultra high energy γ-ray sources for other observations is analysed and possible mechanisms for the production of ultra high energy γ-rays in the sources are discussed. It is demonstrated that if the γ-rays are produced via cosmic ray interactions the sources have to produce very high fluxes of cosmic ray particles. In fact it is possible that a small number of such sources can supply the whole Galactic cosmic ray flux

Input current interharmonics in adjustable speed drives caused by fixed-frequency modulation techniques

DEFF Research Database (Denmark)

Soltani, Hamid; Davari, Pooya; Loh, Poh Chiang

2016-01-01

Adjustable Speed Drives (ASDs) based on double-stage conversion systems may inject interharmonics distortion into the grid, other than the well-known characteristic harmonic components. The problems created by interharmonics make it necessary to find their precise sources, and, to adopt an approp......Adjustable Speed Drives (ASDs) based on double-stage conversion systems may inject interharmonics distortion into the grid, other than the well-known characteristic harmonic components. The problems created by interharmonics make it necessary to find their precise sources, and, to adopt...... an appropriate strategy for minimizing their effects. This paper investigates the ASD's input current interharmonic sources caused by applying symmetrical regularly sampled fixed-frequency modulation techniques on the inverter. The interharmonics generation process is precisely formulated and comparative results...

Dual motor drive vehicle speed synchronization and coordination control strategy

Science.gov (United States)

Huang, Hao; Tu, Qunzhang; Jiang, Chenming; Ma, Limin; Li, Pei; Zhang, Hongxing

2018-04-01

Multi-motor driven systems are more and more widely used in the field of electric engineering vehicles, as a result of the road conditions and the variable load of engineering vehicles, makes multi-motors synchronization coordinated control system as a key point of the development of the electric vehicle drive system. This paper based on electrical machinery transmission speed in the process of engineering vehicles headed for coordinated control problem, summarized control strategies at home and abroad in recent years, made analysis and comparison of the characteristics, finally discussed the trend of development of the multi-motor coordination control, provided a reference for synchronized control system research of electric drive engineering vehicles.

High-speed stimulated Brillouin scattering spectroscopy at 780 nm

Directory of Open Access Journals (Sweden)

Itay Remer

2016-09-01

Full Text Available We demonstrate a high-speed stimulated Brillouin scattering (SBS spectroscopy system that is able to acquire stimulated Brillouin gain point-spectra in water samples and Intralipid tissue phantoms over 2 GHz within 10 ms and 100 ms, respectively, showing a 10-100 fold increase in acquisition rates over current frequency-domain SBS spectrometers. This improvement was accomplished by integrating an ultra-narrowband hot rubidium-85 vapor notch filter in a simplified frequency-domain SBS spectrometer comprising nearly counter-propagating continuous-wave pump-probe light at 780 nm and conventional single-modulation lock-in detection. The optical notch filter significantly suppressed stray pump light, enabling detection of stimulated Brillouin gain spectra with substantially improved acquisition times at adequate signal-to-noise ratios (∼25 dB in water samples and ∼15 dB in tissue phantoms. These results represent an important step towards the use of SBS spectroscopy for high-speed measurements of Brillouin gain resonances in scattering and non-scattering samples.

Effects of balanced and unbalanced voltage sags on DC adjustable-speed drives

Energy Technology Data Exchange (ETDEWEB)

Pedra, Joaquin; Sainz, Luis; Corcoles, Felipe; Bergas, Joan [Department of Electrical Engineering, ETSEIB-UPC, Av. Diagonal, 647, 08028 Barcelona (Spain); de Blas, Alfredo [Department of Electrical Engineering, EUETIB-UPC, C. d' Urgell, 187, 08036 Barcelona (Spain)

2008-06-15

This paper analyzes the sensitivity of DC adjustable-speed drives to balanced and unbalanced voltage sags. The influence of sag type, depth, duration and phase-angle jump on DC drives is studied. The control of the DC drive has been taken into account to understand drive behavior in the presence of voltage sags. Two working modes of the DC motor are considered in the study: as a consumer load and as a regenerative load. When the DC motor works as a consumer load, the study shows that sag type and depth have a significant influence on drive behavior. However, the voltage sag can be ridden through if the rectifier firing angle is set correctly by the control. When the DC motor works as a regenerative load, the study shows the consequences of the three-phase rectifier commutation failure due to the voltage sag. (author)

Polymer Surface Textured with Nanowire Bundles to Repel High-Speed Water Drops.

Science.gov (United States)

Li, Y P; Li, X Y; Zhu, X P; Lei, M K; Lakhtakia, A

2018-05-11

Water drops impacting windshields of high-speed trains and aircraft as well as blades in steam turbine power generators obliquely and at high speeds are difficult to repel. Impacting drops penetrate the void regions of nanotextured and microtextured superhydrophobic coatings, with this pinning resulting in the loss of drop mobility. In order to repel high-speed water drops, we nanotextured polymer surfaces with nanowire bundles separated from their neighbors by microscale void regions, with the nanowires in a bundle separated from their neighbors by nanoscale void regions. Water drops with speeds below a critical speed rebound completely. Water drops with speeds exceeding a critical speed rebound partially, but residual droplets that begin to be pinned undergo a spontaneous dewetting process and slide off. The natural oscillations of residual droplets drive this dewetting process in the interbundle void regions, resulting in a transition from the sticky Wenzel state to the slippery Cassie state without external stimuli.

Magnetically-focusing biochip structures for high-speed active biosensing with improved selectivity

Science.gov (United States)

Yoo, Haneul; Lee, Dong Jun; Kim, Daesan; Park, Juhun; Chen, Xing; Hong, Seunghun

2018-06-01

We report a magnetically-focusing biochip structure enabling a single layered magnetic trap-and-release cycle for biosensors with an improved detection speed and selectivity. Here, magnetic beads functionalized with specific receptor molecules were utilized to trap target molecules in a solution and transport actively to and away from the sensor surfaces to enhance the detection speed and reduce the non-specific bindings, respectively. Using our method, we demonstrated the high speed detection of IL-13 antigens with the improved detection speed by more than an order of magnitude. Furthermore, the release step in our method was found to reduce the non-specific bindings and improve the selectivity and sensitivity of biosensors. This method is a simple but powerful strategy and should open up various applications such as ultra-fast biosensors for point-of-care services.

Wavelet-Fuzzy Speed Indirect Field Oriented Controller for Three-Phase AC Motor Drive

DEFF Research Database (Denmark)

Sanjeevikumar, Padmanaban; Daya, Febin; Blaabjerg, Frede

2016-01-01

Three-phase voltage source inverter driven induction motor are used in many medium- and high-power applications. Precision in speed of the motor play vital role, i.e. popular methods of direct/indirect field-oriented control (FOC) are applied. FOC is employed with proportional-integral (P...... wavelet transform and the fuzzy logic controller, to generate the scaled gains for the indirect FOC induction motor. Complete model of the proposed ac motor drive is developed with numerical simulation Matlab/Simulink software and tested under different working conditions. For experimental verification...

Harmonic Distortion of Rectifier Topologies for Adjustable Speed Drives

DEFF Research Database (Denmark)

Hansen, Steffan

This thesis deals with the harmonic distortion of the diode rectifier and a number of alternative rectifier topologies for adjustable speed drives. The main intention of this thesis is to provide models and tools that allow easy prediction of the harmonic distortion of ASD’s in a given system...... rectifier are presented. The first level is an ideal model where the diode rectifier basically is treated as an independent (harmonic) current source. The second level is an empirical model, where simulated (or measured) values of the harmonic currents of the diode rectifier for different parameters......-angle of the individual harmonic currents of different diode rectifier types is analyzed. Four selected rectifier topologies with a high input power factor are presented. It is shown that using ac- or dc-coils is a very simple and efficient method to reduce the harmonic currents compared to the basic diode rectifier...

Interharmonic mitigation of adjustable speed drives using an active DC-link capacitor

DEFF Research Database (Denmark)

Soltani, Hamid; Loh, Poh Chiang; Blaabjerg, Frede

2015-01-01

Current and voltage source Adjustable - Speed Drives (ASDs) exert distortion currents in the grid which may lead to some interharmonic components other than the characteristic harmonic components. The frequencies of the line current interharmonics, generated by these ASDs, depend on the motor...

Energy saving opportunity with variable speed drive in primary air-handling unit

International Nuclear Information System (INIS)

Li, J.S.M.

2007-01-01

Air conditioners used in the court buildings in Kowloon City, Hong Kong were retrofitted with variable speed drives in the primary air handling unit (PAU) in an effort to reduce energy consumption. The initial effect of this retrofit was investigated along with the feasibility of using a carbon dioxide (CO 2 ) based demand control ventilation to reduce energy consumption while optimizing indoor air quality. The air flow in most air conditioning fans is either constant or controlled by motorized inlet guide vanes. Although this controls the flow and may reduce the load on the fan, this constriction adds an energy loss, resulting in inefficient operation. Variable speed drives should be used on the PAU in order to maintain system efficiency. As the speed of the fans are reduced, the flow will decrease proportionally, while the power required by the fan will reduce the cube of the speed. Therefore, if the fresh air supply can be controlled by reducing the speed of the fan motor, then flow control would be more efficient. The energy saving associated with variable fresh air supply flow rate was evaluated along with the cost to building owners. This paper presented the results of the potential energy and cost savings associated with this retrofit, and included implementation cost and pay back period. It was estimated that about 20 per cent of power consumption and electricity costs can be saved per year, with a simple payback period of 2 years. 7 refs., 3 tabs., 3 figs

Structural modifications of ultra-high molecular weight polyethylene (UHMWPE) processed in attritor type mill

International Nuclear Information System (INIS)

Gabriel, Melina C.; Carvalho, Benjamim de M.; Pinheiro, Luis A.; Cintho, Osvaldo M.; Capocchi, Jose D.T.; Kubaski, Evaldo T.

2009-01-01

Ultra-high molecular weight polyethylene (UHMWPE) is a polyethylene that has a high melt viscosity, hence its processing becomes very difficult. High-energy mechanical milling provides physical and chemical changes in polymers that have been studied recently. In order to study these changes in UHMWPE, powder of this polymer was mechanical milled in attritor type mill with a ball-to-powder weight ratio of 40:1 for 8 hours, varying the rotation speed: 200, 300, 400, 500 e 600 rpm. The polymer was characterized by scanning electron microscopy (SEM) and xray diffraction (XRD). From the XRD results it was noted that as the rotation speed increased the monoclinic phase also increased up to 500 rpm. For 600 rpm, the amount of monoclinic phase apparently decreased. At this rotation speed, the deformation rate probably increased the process temperature, allowing the monoclinic phase to return to its initial structural orthorhombic form. (author)

Do ultra-orphan medicinal products warrant ultra-high prices? A review

Directory of Open Access Journals (Sweden)

Picavet E

2013-06-01

Full Text Available Eline Picavet,1 David Cassiman,2 Steven Simoens1 1Department of Pharmaceutical and Pharmacological Sciences, KU Leuven, Leuven, Belgium; 2Department of Hepatology, University Hospital Leuven, Leuven, Belgium Abstract: Ultra-orphan medicinal products (ultra-OMPs are intended for the treatment, prevention, or diagnosis of ultra-rare diseases, ie, life-threatening or chronically debilitating diseases that affect less than one per 50,000 individuals. Recently, high prices for ultra-OMPs have given rise to debate on the sustainability and justification of these prices. The aim of this article is to review the international scientific literature on the pricing of ultra-OMPs and to provide an overview of the current knowledge on the drivers of ultra-OMP pricing. The pricing process of ultra-OMPs is a complex and nontransparent issue. Evidence in the literature seems to indicate that ultra-OMPs are priced according to rarity and what the manufacturer believes the market will bear. Additionally, there appears to be a trend between the price of an ultra-OMP and the number of available alternatives. Patients, third-party payers, and pharmaceutical companies could benefit from more transparent pricing strategies. With a view to containing health care costs, it is likely that cost-sharing strategies, such as performance-based risk sharing arrangements, will become increasingly more important. However, it is vital that any measures for price control are consistent with the intended goals of the incentives to promote the development of new OMPs. Ideally, a balance must be struck between attaining affordable prices for ultra-OMPs and securing a realistic return on investment for the pharmaceutical industry. Keywords: ultra-orphan medicinal product, ultra-rare disease, pricing

A Very Low-Speed Sensorless Induction Motor Drive with Online Stator Resistance identification scheme

Directory of Open Access Journals (Sweden)

M. Zaky

2008-03-01

Full Text Available Recently, speed sensorless control of induction motor drives received great attention to avoid the different problems associated with direct speed sensors. However, low speed operation with robustness against parameter variations remains an area of research for sensorless systems. Stator resistance is of greatest importance for good operation of speed sensorless systems in low speed region. In this paper, a sliding mode current observer for an induction motor is presented. An estimation algorithm based on this observer in conjunction with Popov's hyper-stability theory is proposed to calculate the speed and stator resistance independently. The proposed speed observer with parallel stator resistance identification is firstly verified by simulation. Experimental results are included as well to demonstrate the good performance of the proposed observer and estimation algorithms at low speed.

Perils of using speed zone data to assess real-world compliance to speed limits.

Science.gov (United States)

Chevalier, Anna; Clarke, Elizabeth; Chevalier, Aran John; Brown, Julie; Coxon, Kristy; Ivers, Rebecca; Keay, Lisa

2017-11-17

Real-world driving studies, including those involving speeding alert devices and autonomous vehicles, can gauge an individual vehicle's speeding behavior by comparing measured speed with mapped speed zone data. However, there are complexities with developing and maintaining a database of mapped speed zones over a large geographic area that may lead to inaccuracies within the data set. When this approach is applied to large-scale real-world driving data or speeding alert device data to determine speeding behavior, these inaccuracies may result in invalid identification of speeding. We investigated speeding events based on service provider speed zone data. We compared service provider speed zone data (Speed Alert by Smart Car Technologies Pty Ltd., Ultimo, NSW, Australia) against a second set of speed zone data (Google Maps Application Programming Interface [API] mapped speed zones). We found a systematic error in the zones where speed limits of 50-60 km/h, typical of local roads, were allocated to high-speed motorways, which produced false speed limits in the speed zone database. The result was detection of false-positive high-range speeding. Through comparison of the service provider speed zone data against a second set of speed zone data, we were able to identify and eliminate data most affected by this systematic error, thereby establishing a data set of speeding events with a high level of sensitivity (a true positive rate of 92% or 6,412/6,960). Mapped speed zones can be a source of error in real-world driving when examining vehicle speed. We explored the types of inaccuracies found within speed zone data and recommend that a second set of speed zone data be utilized when investigating speeding behavior or developing mapped speed zone data to minimize inaccuracy in estimates of speeding.

Optical Amplication for Terabit-per-Second Ultra-High Speed Communication Systems

DEFF Research Database (Denmark)

Lali-Dastjerdi, Zohreh

The present thesis is concerned with fiber optical parametric amplification and regeneration for high-speed optical communication systems. Fiber optical parametric amplifiers (FOPAs) have multi-functional applications depending on their implementation in optical systems. Based on a few femtosecond...... and saturation effect in order to assess the degradation of the amplified signal. In a very good agreement with the performed experiments, it is shown that the noise transferred to the signal can be effectively suppressed by operating in the saturation regime. The amplification of short few picosecond...

Characterization of a high performance ultra-thin heat pipe cooling module for mobile hand held electronic devices

Science.gov (United States)

Ahamed, Mohammad Shahed; Saito, Yuji; Mashiko, Koichi; Mochizuki, Masataka

2017-11-01

In recent years, heat pipes have been widely used in various hand held mobile electronic devices such as smart phones, tablet PCs, digital cameras. With the development of technology these devices have different user friendly features and applications; which require very high clock speeds of the processor. In general, a high clock speed generates a lot of heat, which needs to be spreaded or removed to eliminate the hot spot on the processor surface. However, it is a challenging task to achieve proper cooling of such electronic devices mentioned above because of their confined spaces and concentrated heat sources. Regarding this challenge, we introduced an ultra-thin heat pipe; this heat pipe consists of a special fiber wick structure named as "Center Fiber Wick" which can provide sufficient vapor space on the both sides of the wick structure. We also developed a cooling module that uses this kind of ultra-thin heat pipe to eliminate the hot spot issue. This cooling module consists of an ultra-thin heat pipe and a metal plate. By changing the width, the flattened thickness and the effective length of the ultra-thin heat pipe, several experiments have been conducted to characterize the thermal properties of the developed cooling module. In addition, other experiments were also conducted to determine the effects of changes in the number of heat pipes in a single module. Characterization and comparison of the module have also been conducted both experimentally and theoretically.

The Intention in Speeding Behavior between Low and High Intended Young Driver in Urban University

Directory of Open Access Journals (Sweden)

Mohamad Ghazali Masuri,

2016-01-01

Full Text Available The number of road traffic accidents among young adult aged under 25 years old is an alarming issue in Malaysia. A five pages self-reported questionnaire was distributed to 384 young drivers' to investigate their intention in speeding while driving. Results have shown, the intention to speed among low and high intended based line group revealed a significant difference when it was compared with four types of scenario. Correct stimulation while driving could help drivers to change their intention to speed. This stimulation may be able to reduce the drivers' potential to involve with an accident and will save peoples' life.

The design of high-speed windmills suitable for driving electric generators

Energy Technology Data Exchange (ETDEWEB)

Klein, G J

1975-01-01

A simple windmill theory is presented for designing a small, horizontal axis windmill for powering an automobile-type generator used along with a storage battery. Windmills designed by the method presented in this paper have maximum efficiencies in the order of 0.40 to 0.45, which approaches 75% of the theoretical maximum. Wind tunnel tests were performed on a two-bladed unit designed for a tip speed/wind speed ratio of 7. Maximum efficiency was close to 0.45 at a tip speed/wind speed ratio of slightly over 6. This windmill, if fitted directly to a specially wound three-brush automobile type generator, wil begin to charge a 6-volt battery at a wind speed of 7.5-8 mph. 2 refs., 7 figs., 1 tab.

Driving Skills of Young Adults with Developmental Coordination Disorder: Regulating Speed and Coping with Distraction

Science.gov (United States)

de Oliveira, Rita F.; Wann, John P.

2011-01-01

In two experiments, we used an automatic car simulator to examine the steering control, speed regulation and response to hazards of young adults with developmental coordination disorder (DCD) and limited driving experience. In Experiment 1 participants either used the accelerator pedal to regulate their speed, or used the brake pedal when they…

Analysis of ultra-narrow ferromagnetic domain walls

Energy Technology Data Exchange (ETDEWEB)

Jenkins, Catherine; Paul, David

2012-01-10

New materials with high magnetic anisotropy will have domains separated by ultra-narrow ferromagnetic walls with widths on the order of a few unit cells, approaching the limit where the elastic continuum approximation often used in micromagnetic simulations is accurate. The limits of this approximation are explored, and the static and dynamic interactions with intrinsic crystalline defects and external driving elds are modeled. The results developed here will be important when considering the stability of ultra-high-density storage media.

Modelling and control algorithms of the cross conveyors line with multiengine variable speed drives

Science.gov (United States)

Cheremushkina, M. S.; Baburin, S. V.

2017-02-01

The paper deals with the actual problem of developing the control algorithm that meets the technical requirements of the mine belt conveyors, and enables energy and resource savings taking into account a random sort of traffic. The most effective method of solution of these tasks is the construction of control systems with the use of variable speed drives for asynchronous motors. The authors designed the mathematical model of the system ‘variable speed multiengine drive - conveyor - control system of conveyors’ that takes into account the dynamic processes occurring in the elements of the transport system, provides an assessment of the energy efficiency of application the developed algorithms, which allows one to reduce the dynamic overload in the belt to 15-20%.

The Transfer of Cognitive Speed of Processing Training to Older Adults’ Driving Mobility Across 5 Years

Science.gov (United States)

Edwards, Jerri D.; O’Connor, Melissa L.; Ball, Karlene K.; Wadley, Virginia G.; Vance, David E.

2016-01-01

Objectives. Multilevel models assessed the effects of cognitive speed of processing training (SPT) on older adults’ self-reported driving using intention-to-treat (ITT, randomization to training or control conditions) and dosage (treatment-received via number of training sessions) analyses across 5 years. Method. Participants randomized to SPT (n = 598) were compared with those randomized to either the no-contact control (n = 598) or memory training, which served as an active control (n = 610). Driving mobility (frequency, exposure, and space) was assessed over time. Results. No significant effects were found within the ITT analyses. However, number of SPT sessions did affect driving mobility outcomes. In the full sample (N = 1,806), higher SPT doses were associated with maintained driving frequency as compared with both control groups, but no effects were found for driving exposure or space. Subsample analyses (n = 315) revealed that persons at-risk for mobility declines (i.e., poor initial processing speed) who received additional booster SPT sessions reported greater maintenance of both driving frequency and exposure over time as compared with the no-contact and active control groups. Discussion. These results and prior research indicate that cognitive SPT transfers to prolonged driving mobility among older adults. Future research should investigate the mechanisms behind transfer effects to real-world activities, such as driving. PMID:25878053

Adjustable speed drives improve circulating water system

International Nuclear Information System (INIS)

Dent, R.A.; Dicic, Z.

1994-01-01

This paper illustrates the integration of electrical and mechanical engineering requirements to produce a solution to past problems and future operating demands. The application of adjustable speed drives in the modifications of the circulating water system at Indian Point No. 3 Nuclear Power Plant provided increased operating flexibility, efficiency and avoided otherwise costly renovations to the plant electrical systems. Rectification of the original inadequate design of the circulating water system, in addition to maximizing plant efficiency consistent with environmental considerations, formed the basis for this modification. This entailed replacement of all six circulating water pumps and motors and physical modifications to the intake system. This paper details the methodology used in this engineering task. The new system was installed successfully and has been operating reliably and economically for the past eight years

Effects of passive components on the input current interharmonics of adjustable-speed drives

DEFF Research Database (Denmark)

Soltani, Hamid; Blaabjerg, Frede; Zare, Firuz

2016-01-01

Current and voltage source Adjustable Speed Drives (ASDs) exert distortion current into the grid, which may produce some interharmonic components other than the characteristic harmonic components. This paper studies the effects of passive components on the input current interharmonics of adjustable...

High Speed Gear Sized and Configured to Reduce Windage Loss

Science.gov (United States)

Kunz, Robert F. (Inventor); Medvitz, Richard B. (Inventor); Hill, Matthew John (Inventor)

2013-01-01

A gear and drive system utilizing the gear include teeth. Each of the teeth has a first side and a second side opposite the first side that extends from a body of the gear. For each tooth of the gear, a first extended portion is attached to the first side of the tooth to divert flow of fluid adjacent to the body of the gear to reduce windage losses that occur when the gear rotates. The gear may be utilized in drive systems that may have high rotational speeds, such as speeds where the tip velocities are greater than or equal to about 68 m/s. Some embodiments of the gear may also utilize teeth that also have second extended portions attached to the second sides of the teeth to divert flow of fluid adjacent to the body of the gear to reduce windage losses that occur when the gear rotates.

A study on the design of a low-friction, high-speed pneumatic cylinder

International Nuclear Information System (INIS)

Kim, Do Tae; Kim, Dong Soo; Ju, Min Jin

2008-01-01

Of all of pneumatic components utilized in the make up of pneumatic circuits on either automatic assembly machine or industrial equipment, the pneumatic cylinder is more oriented toward being a structural as well as a pneumatic member. The structural design must be based to a large degree on the end of application of the cylinder on the equipment it is operating. In this paper, design studies of a double-acting pneumatic cushion type cylinder with low-friction and high-speed driving have been developed. Of interest here is to investigate the structural analysis of cylinder tube, piston rod, end cover, and to analyze the buckling of piston rod. Also, a relief valve type cushion mechanism is considered. This cushion mechanism is found to be adequate under a high-speed driving of pneumatic cylinders

Energy-Based Adaptive Sliding Mode Speed Control for Switched Reluctance Motor Drive

Directory of Open Access Journals (Sweden)

M. M. Namazi Isfahani

2012-03-01

Full Text Available Torque ripple minimization of switched reluctance motor drives is a major subject based on these drives’ extensive use in the industry. In this paper, by using a well-known cascaded torque control structure and taking the machine physical structure characteristics into account, the proposed energy-based (passivity-based adaptive sliding algorithm derived from the view point of energy dissipation, control stability and algorithm robustness. First, a nonlinear dynamic model is developed and decomposed into separate slow and fast passive subsystems which are interconnected by negative feedbacks. Then, an outer loop speed control is employed by adaptive sliding controller to determine the appropriate torque command. Finally, to reduce torque ripple in switched reluctance motor a high-performance passivity-based current controller is proposed. It can overcome the inherent nonlinear characteristics of the system and make the whole system robust to uncertainties and bounded disturbances. The performance of the proposed controller algorithm has been demonstrated in simulation, and experimental using a 4KW, four-phase, 8/6 pole SRM DSP-based drive system.

Intelligent speed control and effects on driving behaviour

NARCIS (Netherlands)

Horst, A.R.A. van der; Hogema, J.H.

1999-01-01

Supporting the driver in conducting his nowadays demanding task is a promising means to get the maximum out of the road system with respect to both efficiency and safety. With respect to safety, speed management is a main issue. Police enforcement of speeding is one approach, preventing high speeds

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D. Third year report. Ultra-high density information storage component; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu. Chokomitsudo joho storage component (dai 3 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of industrially creating next generation HDD (hard disk drive), the development was proceeded with of ultra-high density and energy saving type next generation HDD system. The following four were conducted: 1) development of active type magnetic head arm for high speed writing/reading-out; 2) development of ultra-smooth low-noise medium using ultra-clean process; 3) establishment of component technology of high efficiency lubricating materials; 4) development of reproductive magnetic head using TMR device. TMR device is an ultra-high sensitivity magnetic detecting device composed of three layers of ferromagnetic material/insulator/ferromagnetic material. As to the development of regenerative magnetic head, studies were made of the reduction in resistance of TRM device, fabrication of submicron device and system integration. For the development of low resistance TMR device, thickness of Al layer, oxidation conditions and heat treatment conditions were studied in detail. The tunnel joining was obtained in which RA value and TMR ratio are 80 ohm(center dot){mu}m{sup 2} and 30%, respectively, in case of the thickness of Al layer of 6.6 (angstrom). (NEDO)

Evidence that attitude accessibility augments the relationship between speeding attitudes and speeding behavior: a test of the MODE model in the context of driving.

Science.gov (United States)

Elliott, Mark A; Lee, Emme; Robertson, Jamie S; Innes, Rhona

2015-01-01

According to the MODE model of attitude-to-behavior processes, attitude accessibility augments attitude-behavior correspondence, reflecting an automatic influence of attitudes on behavior. We therefore tested whether attitude accessibility moderates the attitude-behavior relationship in a context that is governed by characteristically automatic behavior, namely driving. In study 1 (correlational design), participants (N=130) completed online questionnaire measures of the valences and accessibilities of their attitudes towards speeding. Two weeks later, online questionnaire measures of subsequent speeding behavior were obtained. Attitude valence was a significantly better predictor of behavior at high (mean+1SD) versus low (mean-1SD) levels of attitude accessibility. In study 2 (experimental design), attitude accessibility was manipulated with a repeated attitude expression task. Immediately after the manipulation, participants (N=122) completed online questionnaire measures of attitude valence and accessibility, and two weeks later, subsequent speeding behavior. Increased attitude accessibility in the experimental (versus control) condition generated an increase in attitude-behavior correspondence. The findings are consistent with the MODE model's proposition that attitudes can exert an automatic influence on behavior. Interventions to reduce speeding could usefully increase the accessibility of anti-speeding attitudes and reduce the accessibility of pro-speeding attitudes. Copyright © 2014 Elsevier Ltd. All rights reserved.

Comparison of ultra high performance supercritical fluid chromatography, ultra high performance liquid chromatography, and gas chromatography for the separation of synthetic cathinones.

Science.gov (United States)

Carnes, Stephanie; O'Brien, Stacey; Szewczak, Angelica; Tremeau-Cayel, Lauriane; Rowe, Walter F; McCord, Bruce; Lurie, Ira S

2017-09-01

A comparison of ultra high performance supercritical fluid chromatography, ultra high performance liquid chromatography, and gas chromatography for the separation of synthetic cathinones has been conducted. Nine different mixtures of bath salts were analyzed in this study. The three different chromatographic techniques were examined using a general set of controlled synthetic cathinones as well as a variety of other synthetic cathinones that exist as positional isomers. Overall 35 different synthetic cathinones were analyzed. A variety of column types and chromatographic modes were examined for developing each separation. For the ultra high performance supercritical fluid chromatography separations, analyses were performed using a series of Torus and Trefoil columns with either ammonium formate or ammonium hydroxide as additives, and methanol, ethanol or isopropanol organic solvents as modifiers. Ultra high performance liquid chromatographic separations were performed in both reversed phase and hydrophilic interaction chromatographic modes using SPP C18 and SPP HILIC columns. Gas chromatography separations were performed using an Elite-5MS capillary column. The orthogonality of ultra high performance supercritical fluid chromatography, ultra high performance liquid chromatography, and gas chromatography was examined using principal component analysis. For the best overall separation of synthetic cathinones, the use of ultra high performance supercritical fluid chromatography in combination with gas chromatography is recommended. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Lifetime Benchmarking of Two DC-link Passive Filtering Configurations in Adjustable Speed Drives

DEFF Research Database (Denmark)

Wang, Haoran; Davari, Pooya; Wang, Huai

2018-01-01

Electrolytic capacitors with a DC-side inductor, and the slim DC-link capacitor are two typical filtering configurations in Adjustable Speed Drives (ASDs). The reliability performance of these capacitive DC-link solutions is an essential aspect to be considered, which depends on both component in...

Design and application on experimental platform for high-speed bearing with grease lubrication

Directory of Open Access Journals (Sweden)

He Qiang

2015-12-01

Full Text Available The experimental platform for high-speed grease is an important tool for research and development of high-speed motorized spindle with grease lubrication. In this article, the experimental platform for high-speed grease is designed and manufactured which consists of the drive system, the test portion, the loading system, the lubrication system, the control system, and so on. In the meantime, the high-speed angular contact ceramic ball bearings B7005C/HQ1P4 as the research object are tested and contrasted in the grease lubrication and oil mist lubrication. The experimental platform performance is validated by contrast experiment, and the high-speed lubricated bearing performance is also studied especially in the relationship among the rotating speed,load and temperature rise. The results show that the experimental platform works steadily, accurate, and reliable in the experimental testing. And the grease lubrication ceramic ball bearings B7005C/HQ1P4 can be used in high-speed motorized spindle in the circular water cooling conditions when the rotating speed is lower than 40,000 r/min or the DN value (the value of the bearing diameter times the rotating speed is lower than the 1.44 × 106 mm r/min. Grease lubrication instead of oil mist lubrication under high-speed rotating will simplify the structure design of the high-speed motorized spindle and reduce the pollution to the environment.

The Transfer of Cognitive Speed of Processing Training to Older Adults' Driving Mobility Across 5 Years.

Science.gov (United States)

Ross, Lesley A; Edwards, Jerri D; O'Connor, Melissa L; Ball, Karlene K; Wadley, Virginia G; Vance, David E

2016-01-01

Multilevel models assessed the effects of cognitive speed of processing training (SPT) on older adults' self-reported driving using intention-to-treat (ITT, randomization to training or control conditions) and dosage (treatment-received via number of training sessions) analyses across 5 years. Participants randomized to SPT (n = 598) were compared with those randomized to either the no-contact control (n = 598) or memory training, which served as an active control (n = 610). Driving mobility (frequency, exposure, and space) was assessed over time. No significant effects were found within the ITT analyses. However, number of SPT sessions did affect driving mobility outcomes. In the full sample (N = 1,806), higher SPT doses were associated with maintained driving frequency as compared with both control groups, but no effects were found for driving exposure or space. Subsample analyses (n = 315) revealed that persons at-risk for mobility declines (i.e., poor initial processing speed) who received additional booster SPT sessions reported greater maintenance of both driving frequency and exposure over time as compared with the no-contact and active control groups. These results and prior research indicate that cognitive SPT transfers to prolonged driving mobility among older adults. Future research should investigate the mechanisms behind transfer effects to real-world activities, such as driving. © The Author 2015. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Ultra-high surface speed for metal removal, artillery shell

Science.gov (United States)

Pugh, R. F.; Walsh, M. R.; Pohl, R. F.

1981-07-01

Four types of steel (AISI 1340, 4140, 4340, and HF-1) which are commonly used in large caliber projectile manufacture were machined with five types of tools at different hardness ranges representing the as-forged and the heat-treated condition. Results show that machining speeds can be increased significantly over current practice using the present available tooling.

Ultra high tip speed (670.6 m/sec) fan stage with composite rotor: Aerodynamic and mechanical design

Science.gov (United States)

Halle, J. E.; Burger, G. D.; Dundas, R. E.

1977-01-01

A highly loaded, single-stage compressor having a tip speed of 670.6 m/sec was designed for the purpose of investigating very high tip speeds and high aerodynamic loadings to obtain high stage pressure ratios at acceptable levels of efficiency. The design pressure ratio is 2.8 at an adiabatic efficiency of 84.4%. Corrected design flow is 83.4 kg/sec; corrected design speed is 15,200 rpm; and rotor inlet tip diameter is 0.853 m. The rotor uses multiple-circular-arc airfoils from 0 to 15% span, precompression airfoils assuming single, strong oblique shocks from 21 to 43% span, and precompression airfoils assuming multiple oblique shocks from 52% span to the tip. Because of the high tip speeds, the rotor blades are designed to be fabricated of composite materials. Two composite materials were investigated: Courtaulds HTS graphite fiber in a Kerimid 601 polyimide matrix and the same fibers in a PMR polyimide matrix. In addition to providing a description of the aerodynamic and mechanical design of the 670.0 m/sec fan, discussion is presented of the results of structural tests of blades fabricated with both types of matrices.

Novel Position and Speed Estimator for PM Single Phase Brushless D.C. Motor Drives

DEFF Research Database (Denmark)

Lepure, Liviu I.; Andreescu, Gheorghe-Daniel; Iles, Doris

2010-01-01

A novel position and speed estimator for single phase permanent magnet brushless d.c. (PMBLDC) motor drives, based on flux integration and prior knowledge of ΨPM (θ) is proposed here and an adequate correction algorithm is adopted in order to increase the robustness to noise and to reduce...... the sensitivity to accuracy of flux linkage estimation. A speed and current close loop control is employed based on the Hall signal and the motor is controlled at different speeds in order to validate the proposed estimation algorithm with satisfying results. The position correction effect is analyzed...

Latest Progress in Research on the SpaceLiner High-Speed Passenger Transportation Concept

OpenAIRE

Sippel, Martin; van Foreest, Arnold

2007-01-01

A vision aimed at revolutionizing ultra-long distance travel between different points on earth could be realized by a high-speed intercontinental passenger transport using rocket based, suborbital launchers. The paper gives an overview on the latest progress in conceptual design of the DLR SpaceLiner presenting geometrical size and mass data and describing results of trajectory simulations. The rockets are based on an advanced but technically conservative approach not relying on e...

Sex Difference in Draft-Legal Ultra-Distance Events - A Comparison between Ultra-Swimming and Ultra-Cycling.

Science.gov (United States)

Salihu, Lejla; Rüst, Christoph Alexander; Rosemann, Thomas; Knechtle, Beat

2016-04-30

Recent studies reported that the sex difference in performance in ultra-endurance sports such as swimming and cycling changed over the years. However, the aspect of drafting in draft-legal ultra-endurance races has not yet been investigated. This study investigates the sex difference in ultra-swimming and ultra-cycling draft-legal races where drafting - swimming or cycling behind other participants to save energy and have more power at the end of the race to overtake them, is allowed. The change in performance of the annual best and the annual three best in an ultra-endurance swimming race (16-km 'Faros Swim Marathon') over 38 years and in a 24-h ultra-cycling race ('World Cycling Race') over 13 years were compared and analysed with respect to sex difference. Furthermore, performances of the fastest female and male finishers ever were compared. In the swimming event, the sex difference of the annual best male and female decreased non-significantly (P = 0.262) from 5.3% (1976) to 1.0% (2013). The sex gap of speed in the annual three fastest swimmers decreased significantly (P = 0.043) from 5.9 ± 1.6% (1979) to 4.7 ± 3.1% (2013). In the cycling event, the difference in cycling speed between the annual best male and female decreased significantly (P = 0.026) from 33.31% (1999) to 10.89% (2011). The sex gap of speed in the annual three fastest decreased significantly (P = 0.001) from 32.9 ± 0.6% (1999) to 16.4 ± 5.9% (2011). The fastest male swimmer ever (swimming speed 5.3 km/h, race time: 03:01:55 h:min:s) was 1.5% faster than the fastest female swimmer (swimming speed 5.2 km/h, race time: 03:04:09 h:min:s). The three fastest male swimmers ever (mean 5.27 ± 0.13 km/h) were 4.4% faster than the three fastest female swimmers (mean 5.05 ± 0.20 km/h) (P swimming and cycling, the sex difference in the annual top and annual top three swimmers and cyclists decreased (i.e. non-linearly in swimmers and linearly in cyclists) over the years. The sex difference of the

PV Array Driven Adjustable Speed Drive for a Lunar Base Heat Pump

Science.gov (United States)

Domijan, Alexander, Jr.; Buchh, Tariq Aslam

1995-01-01

A study of various aspects of Adjustable Speed Drives (ASD) is presented. A summary of the relative merits of different ASD systems presently in vogue is discussed. The advantages of using microcomputer based ASDs is now widely understood and accepted. Of the three most popular drive systems, namely the Induction Motor Drive, Switched Reluctance Motor Drive and Brushless DC Motor Drive, any one may be chosen. The choice would depend on the nature of the application and its requirements. The suitability of the above mentioned drive systems for a photovoltaic array driven ASD for an aerospace application are discussed. The discussion is based on the experience of the authors, various researchers and industry. In chapter 2 a PV array power supply scheme has been proposed, this scheme will have an enhanced reliability in addition to the other known advantages of the case where a stand alone PV array is feeding the heat pump. In chapter 3 the results of computer simulation of PV array driven induction motor drive system have been included. A discussion on these preliminary simulation results have also been included in this chapter. Chapter 4 includes a brief discussion on various control techniques for three phase induction motors. A discussion on different power devices and their various performance characteristics is given in Chapter 5.

Reduce consumption, improve production. Electronic adjustable speed drives and high performance motors; Consommez moins, produisez mieux. Variateurs electroniques de vitesse et moteurs performants

Energy Technology Data Exchange (ETDEWEB)

David, A.; Pratmarty, D.; Dessoude, M. [Electricite de France (EDF), 92 - Clamart (France). Direction des Etudes et Recherches

1995-10-01

The electric power consumption from electric motors accounts for up to two third of industry`s electric power consumption. When equipped with electronic adjustable speed drives (ASD), energy savings of 10 to 50 percent, with an estimated average of 25 percent, may be achieved for pumps, fans and compressors, which account for 63 percent of motor applications. The advantages of electronic ASD, the installation recommendations which should be applied, the sensibility of ASDs to power cuts and harmonics, the characteristics of high efficiency motors, the energy aspects of motors with or without electronic ASD, and the EDF-ADEME (French energy conservation agency) approach for electricity demand side management, are described

To the Problem of Electromechanical Interaction in Elevators with Controlled Electric Drive and Fuzzy Speed Controller

Directory of Open Access Journals (Sweden)

A. S. Koval

2010-01-01

Full Text Available The paper considers problems concerning electromechanical interaction in elevators with an adjustable asynchronous electric drive equipped with the vector control systems under direct torque control and direct torque control with pulse-width modulator. A mathematical description of electromechanical elevator system with due account of nonlinearity of the worm gear is given in the paper. The paper presents a simplified circuit design of a control system with a fuzzy speed controller. It has been established that the factor of electromechanical interaction in electromechanical system with the adjustable asynchronous electric drive and an fuzzy speed controller is within the range which corresponds to existence of the essential electromechanical interaction.

Speed-calming measures and their Effect on driving speed

DEFF Research Database (Denmark)

Agerholm, Niels; Knudsen, Daniel; Variyeswaran, Kajan

2017-01-01

Highlights •Speed humps and chicanes are widespread speed-calming measures. •Humps and chicanes have virtually the same reducing effect on mean speed. •Chicanes reduce speed variation less than humps and might therefore be a less safe measure....

High speed atom source

International Nuclear Information System (INIS)

Hoshino, Hitoshi.

1990-01-01

In a high speed atom source, since the speed is not identical between ions and electrons, no sufficient neutralizing effect for ionic rays due to the mixing of the ionic rays and the electron rays can be obtained failing to obtain high speed atomic rays at high density. In view of the above, a speed control means is disposed for equalizing the speed of ions forming ionic rays and the speed of electrons forming electron rays. Further, incident angle of the electron rays and/or ionic rays to a magnet or an electrode is made variable. As a result, the relative speed between the ions and the electrons to the processing direction is reduced to zero, in which the probability of association between the ions and the electrons due to the coulomb force is increased to improve the neutralizing efficiency to easily obtain fine and high density high speed electron rays. Further, by varying the incident angle, a track capable of obtaining an ideal mixing depending on the energy of the neutralized ionic rays is formed. Since the high speed electron rays has such high density, they can be irradiated easily to the minute region of the specimen. (N.H.)

The Effect of Rotor Cruise Tip Speed, Engine Technology and Engine/Drive System RPM on the NASA Large Civil Tiltrotor (LCTR2) Size and Performance

Science.gov (United States)

Robuck, Mark; Wilkerson, Joseph; Maciolek, Robert; Vonderwell, Dan

2012-01-01

A multi-year study was conducted under NASA NNA06BC41C Task Order 10 and NASA NNA09DA56C task orders 2, 4, and 5 to identify the most promising propulsion system concepts that enable rotor cruise tip speeds down to 54% of the hover tip speed for a civil tiltrotor aircraft. Combinations of engine RPM reduction and 2-speed drive systems were evaluated. Three levels of engine and the drive system advanced technology were assessed; 2015, 2025 and 2035. Propulsion and drive system configurations that resulted in minimum vehicle gross weight were identified. Design variables included engine speed reduction, drive system speed reduction, technology, and rotor cruise propulsion efficiency. The NASA Large Civil Tiltrotor, LCTR, aircraft served as the base vehicle concept for this study and was resized for over thirty combinations of operating cruise RPM and technology level, quantifying LCTR2 Gross Weight, size, and mission fuel. Additional studies show design sensitivity to other mission ranges and design airspeeds, with corresponding relative estimated operational cost. The lightest vehicle gross weight solution consistently came from rotor cruise tip speeds between 422 fps and 500 fps. Nearly equivalent results were achieved with operating at reduced engine RPM with a single-speed drive system or with a two-speed drive system and 100% engine RPM. Projected performance for a 2025 engine technology provided improved fuel flow over a wide range of operating speeds relative to the 2015 technology, but increased engine weight nullified the improved fuel flow resulting in increased aircraft gross weights. The 2035 engine technology provided further fuel flow reduction and 25% lower engine weight, and the 2035 drive system technology provided a 12% reduction in drive system weight. In combination, the 2035 technologies reduced aircraft takeoff gross weight by 14% relative to the 2015 technologies.

Stretchers and compressors for ultra-high power laser systems

Energy Technology Data Exchange (ETDEWEB)

Yakovlev, I V [Institute of Applied Physics, Russian Academy of Sciences, Nizhnii Novgorod (Russian Federation)

2014-05-30

This review is concerned with pulse stretchers and compressors as key components of ultra-high power laser facilities that take advantage of chirped-pulse amplification. The potentialities, characteristics, configurations and methods for the matching and alignment of these devices are examined, with particular attention to the history of the optics of ultra-short, ultra-intense pulses before and after 1985, when the chirped-pulse amplification method was proposed, which drastically changed the view of the feasibility of creating ultra-high power laser sources. The review is intended primarily for young scientists and experts who begin to address the amplification and compression of chirped pulses, experts in laser optics and all who are interested in scientific achievements in the field of ultra-high power laser systems. (review)

High speed subfractional HP-motor with permanent magnets

International Nuclear Information System (INIS)

Hanitsch, R.; Frenzel, B.

1998-01-01

During the last years an increasing demand for small permanent magnet motors can be detected, especially in the fields of medical applications. For heart assist devices there is the request to have small high speed devices operating at low voltage supply with almost no overtemperature. The design of a special hollow shaft motor for the speed range of 15000..25000 rpm and a torque of 4 to 8 mNm will be outlined. The low noise requirements and the high efficiency request lead to a design with an airgap winding. A thermal analysis is also done in order to meet the conditions given by the medical specialists. The features of the prototype will be presented and also the sensorless control strategy will be outlined. Measured and calculated data show good agreement. Focus will be on the magnetic circuit and the thermal behaviour and not on the control aspects of the motor. Specific parameters demonstrate the good quality of the drive system. (orig.)

High-speed ultra-wideband wireless signals over fiber systems: Photonic generation and DSP detection

DEFF Research Database (Denmark)

Yu, Xianbin; Gibbon, Timothy Braidwood; Tafur Monroy, Idelfonso

2009-01-01

We firstly review the efforts in the literature on UWB over-fiber systems. Secondly, we present experimental results on photonic generation of high-speed UWB signals by both direct modulation and external optical injecting an uncooled semiconductor laser. Furthermore, we introduce the use of digi...

High-speed photoacoustic imaging using an LED-based photoacoustic imaging system

Science.gov (United States)

Sato, Naoto; Kuniyil Ajith Singh, Mithun; Shigeta, Yusuke; Hanaoka, Takamitsu; Agano, Toshitaka

2018-02-01

Recently we developed a multispectral LED-based photoacoustic/ultrasound imaging system (AcousticX) and have been continuously working on its technical/functional improvements. AcousticX is a linear array ultrasound transducer (128 elements, 10 MHz)-based system in which LED arrays (selectable wavelengths, pulse repetition frequency: 4 kHz, pulse width: tunable from 40 - 100 ns) are fixed on both sides of the transducer to illuminate the tissue for photoacoustic imaging. The ultrasound/photoacoustic data from all 128 elements can be simultaneously acquired, processed and displayed. We already demonstrated our system's capability to perform photoacoustic/ultrasound imaging for dynamic imaging of the tissue at a frame rate of 10 Hz (for example to visualize the pulsation of arteries in vivo in human subjects). In this work, we present the development of a new high-speed imaging mode in AcousticX. In this mode, instead of toggling between ultrasound and photoacoustic measurements, it is possible to continuously acquire only photoacoustic data for 1.5 seconds with a time interval of 1 ms. With this improvement, we can record photoacoustic signals from the whole aperture (38 mm) at fast rate and can be reviewed later at different speeds for analyzing dynamic changes in the photoacoustic signals. We believe that AcousticX with this new high-speed mode opens up a feasible technical path for multiple dynamic studies, for example one which focus on imaging the response of voltage sensitive dyes. We envisage to improve the acquisition speed further in future for exploring ultra-high-speed applications.

Recent Developments In High Speed Lens Design At The NPRL

Science.gov (United States)

Mcdowell, M. W.; Klee, H. W.

1987-09-01

Although the lens provides the link between the high speed camera and the outside world, there has over the years been little evidence of co-operation between the optical design and high speed photography communities. It is still only too common for a manufacturer to develop a camera of improved performance and resolution and then to combine this with a standard camera lens. These lenses were often designed for a completely different recording medium and, more often than not, their use results in avoidable degradation of the overall system performance. There is a tendency to assume that a specialized lens would be too expensive and that pushing the aperture automatically implies more complex optical systems. In the present paper some recent South African developments in the design of large aperture lenses are described. The application of a new design principle, based on the work earlier this century of Bernhard Schmidt, shows that ultra-fast lenses need not be overly complex and a basic four-element lens configuration can be adapted to a wide variety of applications.

Ultra high field magnetic resonance imaging

International Nuclear Information System (INIS)

Lethimonnier, F.; Vedrine, P.

2007-01-01

Understanding human brain function, brain development and brain dysfunction is one of the great challenges of the twenty first century. Biomedical imaging has now run up against a number of technical constraints that are exposing limits to its potential. In order to overcome the current limits to high-field magnetic resonance cerebral imaging (MRI) and unleash its fullest potential, the Cea has built NeuroSpin, an ultra-high-field neuroimaging facility at its Saclay centre (in the Essonne). NeuroSpin already boasts three fully operational MRI systems. The first is a 3-tesla high-field system and the second is a very-high-field 7-tesla system, both of which are dedicated to clinical studies and investigations in humans, while the third is an ultra-high-field 17.65-tesla system designed for studies on small animals. In 2011, NeuroSpin will be commissioning an 11.7-tesla ultra-high-field system of unprecedented power that is designed for research on human subjects. The level of the magnetic field and the scale required will make this joint French-German project to build the magnet a breakthrough in the international arena. (authors)

An Energy Efficient Hydraulic Winch Drive Concept Based on a Speed-variable Switched Differential Pump

DEFF Research Database (Denmark)

Schmidt, Lasse; Andersen, Torben O.; Pedersen, Henrik Clemmensen

2017-01-01

controls. Such solutions are typically constituted by many and rather expensive components, and are furthermore often suffering from low frequency dynamics. In this paper an alternative solution is proposed for winch drive operation, which is based on the so-called speed-variable switched differential pump......, originally designed for direct drive of hydraulic differential cylinders. This concept utilizes three pumps, driven by a single electric servo drive. The concept is redesigned for usage in winch drives, driven by flow symmetric hydraulic motors and single directional loads as commonly seen in e.g. active...... heave compensation applications. A general drive configuration approach is presented, along with a proper control strategy and design. The resulting concept is evaluated when applied for active heave compensation. Results demonstrate control performance on level with conventional valve solutions...

A high-speed Schottky detector for ultra-wideband communications

DEFF Research Database (Denmark)

Valdecasa, Guillermo Silva; Cimoli, Bruno; Blanco Granja, Ángel

2017-01-01

This letter reviews the design procedure of a high‐speed Schottky video detector for high‐data‐rate communications within the ultra‐wideband (UWB) frequencies. The classic design approach for video detectors is extended with a mixer‐like analysis, which results in a more detailed assessment of th....... Using 0 dBm carrier power, the lowest measured conversion loss is 10 dB for a video frequency of 1.1 GHz and better than 13 dB up to 1.8 GHz....

The effect of cognitive remediation in individuals at ultra-high risk for psychosis

DEFF Research Database (Denmark)

Glenthøj, Louise Birkedal; Hjorthøj, Carsten; Kristensen, Tina Dam

2017-01-01

of five studies that reported a cognitive outcome found cognitive remediation to improve cognition in the domains of verbal memory, attention, and processing speed. Two out of four studies that reported on functional outcome found cognitive remediation to improve the functional outcome in the domains...... of social functioning and social adjustment. Zero out of the five studies that reported such an outcome found cognitive remediation to affect the magnitude of clinical symptoms. Research on the effect of cognitive remediation in the ultra-high risk state is still scarce. The current state of evidence...

Efficiency trends in electric machines and drives

International Nuclear Information System (INIS)

Mecrow, B.C.; Jack, A.G.

2008-01-01

Almost all electricity in the UK is generated by rotating electrical generators, and approximately half of it is used to drive electrical motors. This means that efficiency improvements to electrical machines can have a very large impact on energy consumption. The key challenges to increased efficiency in systems driven by electrical machines lie in three areas: to extend the application of variable-speed electric drives into new areas through reduction of power electronic and control costs; to integrate the drive and the driven load to maximise system efficiency; and to increase the efficiency of the electrical drive itself. In the short to medium term, efficiency gains within electrical machines will result from the development of new materials and construction techniques. Approximately a quarter of new electrical machines are driven by variable-speed drives. These are a less mature product than electrical machines and should see larger efficiency gains over the next 50 years. Advances will occur, with new types of power electronic devices that reduce switching and conduction loss. With variable-speed drives, there is complete freedom to vary the speed of the driven load. Replacing fixed-speed machines with variable-speed drives for a high proportion of industrial loads could mean a 15-30% energy saving. This could save the UK 15 billion kWh of electricity per year which, when combined with motor and drive efficiency gains, would amount to a total annual saving of 24 billion kWh

An investigation of laser cutting quality of 22MnB5 ultra high strength steel using response surface methodology

Science.gov (United States)

Tahir, Abdul Fattah Mohd; Aqida, Syarifah Nur

2017-07-01

In hot press forming, changes of mechanical properties in boron steel blanks have been a setback in trimming the final shape components. This paper presents investigation of kerf width and heat affected zone (HAZ) of ultra high strength 22MnB5 steel cutting. Sample cutting was conducted using a 4 kW Carbon Dioxide (CO2) laser machine with 10.6 μm wavelength with the laser spot size of 0.2 mm. A response surface methodology (RSM) using three level Box-Behnken design of experiment was developed with three factors of peak power, cutting speed and duty cycle. The parameters were optimised for minimum kerf width and HAZ formation. Optical evaluation using MITUTOYO TM 505 were conducted to measure the kerf width and HAZ region. From the findings, laser duty cycle was crucial to determine cutting quality of ultra-high strength steel; followed by cutting speed and laser power. Meanwhile, low power intensity with continuous wave contributes the narrowest kerf width formation and least HAZ region.

Ultra-wideband wireless receiver front-end for high-speed indoor applications

Directory of Open Access Journals (Sweden)

Zhe-Yang Huang

2014-12-01

Full Text Available Low-noise, ultra-wideband (UWB wireless receiver front-end circuits were presented in this study. A two-stage common-source low-noise amplifier with wideband input impedance matching network, an active-balun and a double-balanced down-conversion mixer were adopted in the UWB wireless receiver front-end. The proposed wireless receiver front-end circuits were implemented in 0.18 μm radio-frequency-CMOS process. The maximum down-conversion power gain of the front-end is 25.8 dB; minimum single-sideband noise figure of the front-end is 4.9 dB over complete UWB band ranging from 3.1 to 10.6 GHz. Power consumption including buffers is 39.2 mW.

DrivingSense: Dangerous Driving Behavior Identification Based on Smartphone Autocalibration

Directory of Open Access Journals (Sweden)

Chunmei Ma

2017-01-01

Full Text Available Since pervasive smartphones own advanced computing capability and are equipped with various sensors, they have been used for dangerous driving behaviors detection, such as drunk driving. However, sensory data gathered by smartphones are noisy, which results in inaccurate driving behaviors estimations. Some existing works try to filter noise from sensor readings, but usually only the outlier data are filtered. The noises caused by hardware of the smartphone cannot be removed from the sensor reading. In this paper, we propose DrivingSense, a reliable dangerous driving behavior identification scheme based on smartphone autocalibration. We first theoretically analyze the impact of the sensor error on the vehicle driving behavior estimation. Then, we propose a smartphone autocalibration algorithm based on sensor noise distribution determination when a vehicle is being driven. DrivingSense leverages the corrected sensor parameters to identify three kinds of dangerous behaviors: speeding, irregular driving direction change, and abnormal speed control. We evaluate the effectiveness of our scheme under realistic environments. The results show that DrivingSense, on average, is able to detect the driving direction change event and abnormal speed control event with 93.95% precision and 90.54% recall, respectively. In addition, the speed estimation error is less than 2.1 m/s, which is an acceptable range.

CD-RW/DVD-ROM drive SD-R1002; CD-RW/DVD-ROM drive SD-R1002

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With the availability of DVD programs increasing at a rapid rate, it has become a general practice to equip a personal computer with a DVD-ROM drive. Toshiba, with a view to meeting the sharp increase in the demand for CD-R/RW (Recordable/ReWritable) recording these days, has commercialized a CD-R/RW drive capable of DVD-ROM reproduction and thereby newly entered into the CD-R/RW drive market. The new product is characterized by (1) the height halved to 41.5mm, (2) quad-speed CD-R/RW recording, (3) 24-speed CD-ROM playback at the maximum, (4) 4.8-speed DVD-ROM playback at the maximum, (5) ATAPI (AT Packet Interface) interface, and (6) access at high speeds, 160ms for DVD and 110ms for CD. (translated by NEDO)

Switched reluctance drive for mass application

Energy Technology Data Exchange (ETDEWEB)

Bitchkov, M.G.; Ilinski, N.F.; Sementchuk, V.A. [Moscow Power Engineering Inst. (Russian Federation)

2000-07-01

Variable speed drives (VSDs) are the most effective means for energy saving in many practical applications particularly in pumps, fans, compressors, conveyors, etc. Up to now the only wide used VSD is a frequency controlled electric drive with AC induction motor. A switched reluctance drive (SRD) having noticeable advantages such as simple construction, low cost, high reliability, high efficiency, etc. still does not compete with traditional AC drives mainly because of the following unsolved problems: complexity of proper control, necessity of a rotor position sensor, poor acoustic characteristics. Results of R and D project realised in Moscow Power Engineering Institute in co-operation with Jaroslavl electric machine-building plant allowed to overcome the above mentioned problems and to obtain reliable low cost sensorless SRD with high efficiency and acceptable acoustic characteristics. The original sensorless SRD version is based on current measuring and exploiting a specially organized observer that provides a stable drive operation within broad speed-torque ranges. Acoustic SRD characteristics were improved by means of proper current pulses shape control. Small increasing the time of current pulse trailing edge allowed to decrease the noise level to 70 dB(A) and brought the SRD to a vary smooth operation even at a low speed. (orig.)

The prevalence of speeding and drunk driving in two cities in China: a mid project evaluation of ongoing road safety interventions.

Science.gov (United States)

Bhalla, Kavi; Li, Qingfeng; Duan, Leilen; Wang, Yuan; Bishai, David; Hyder, Adnan A

2013-12-01

Road traffic crashes in China kill in excess of 250,000 people annually, more than any other country in the world. They are the fourth leading cause of premature death in the country and are responsible for 2.4% of the burden of non-fatal health loss in the country. Interventions to curb speeding and drunk driving are being implemented in the cities of Suzhou and Dalian since late 2010. We evaluated the ongoing effect of these activities through five roadside surveys, seven rounds of observational studies, and analysis of crash statistics in the two cities. We find that thus far, the prevalence of speeding has not reduced in either city with the notable exception of one site in Dalian, where the percentage of speeding vehicles declined from nearly 70% to below 10% after an interval-based speed enforcement system was installed. The broader deployment of such speed control technologies across China and other countries should be explored. Roadside alcohol testing suggests that prevalence of drunk driving (i.e. BAC >20 mg%) declined from 6.4% to 0.5% in Suzhou and from 1.7% to 0.7% in Dalian during the monitored time period. However, the measured prevalence rates are very low and should be validated against estimates based on hospital studies. Roadside interviews suggest that the population of both cities is already highly sensitized to the risks associated with drunk driving and speeding. Crash statistics from the two cities do not show appreciable declines in injuries and fatalities as yet. However, the possibility of substantial underreporting in crash statistics sourced from traffic police poses a severe threat to monitoring progress towards road safety in Suzhou, Dalian and across China. There is an urgent need for China to invest in a reliable road traffic injury surveillance system that can provide information for describing key risk factors, evaluating the impact of safety policies, and benchmarking achievements. Copyright © 2013 Elsevier Ltd. All rights

35 Gb/s Ultra-wideband Technology for Advanced Communications

DEFF Research Database (Denmark)

Puerta Ramírez, Rafael; Vegas Olmos, Juan José; Tafur Monroy, Idelfonso

be applied, evolving from classic spectral inefficient pulsebased systems to more advanced and flexible modulation schemes. Ultra-wideband technology is suitable for low-power high-speed wireless communication systems over short distances, and is an appealing alternative for next generation networks ranging......The fast development of electronics and portable devices, intended mainly for multimedia applications, is increasing exponentially the data traffic demands per user. To cope with these new data demands in limited bandwidth systems, new technologies must be explored and new transmission schemes must...... from high-speed wireless personal area networks, to the internet of things applications. Its popularity stems from the fact that they can be used as an overlay to existing systems, without interference, operating in parallel to existing wireless systems, which perceive ultra-wideband emissions...

Low-Cost High-Speed In-Plane Stroboscopic Micro-Motion Analyzer

Directory of Open Access Journals (Sweden)

Shashank S. Pandey

2017-11-01

Full Text Available Instrumentation for high-speed imaging and laser vibrometry is essential for the understanding and analysis of microstructure dynamics, but commercial instruments are largely unaffordable for most microelectromechanical systems (MEMS laboratories. We present the implementation of a very low cost in-plane micro motion stroboscopic analyzer that can be directly attached to a conventional probe station. The low-cost analyzer has been used to characterize the harmonic motion of 52.1 kHz resonating comb drive microactuators using ~50 ns pulsed light-emitting diode (LED stroboscope exposure times, producing sharp and high resolution (~0.5 μm device images at resonance, which rivals those of several orders of magnitude more expensive systems. This paper details the development of the high-speed stroboscopic imaging system and presents experimental results of motion analysis of example microstructures and a discussion of its operating limits. The system is shown to produce stable stroboscopic LED illumination to freeze device images up to 11 MHz.

Speed Sensorless vector control of parallel-connected three-phase two-motor single-inverter drive system

DEFF Research Database (Denmark)

Gunabalan, Ramachandiran; Sanjeevikumar, Padmanaban; Blaabjerg, Frede

2016-01-01

to noise and parameter uncertainty. The gain matrix is absent in the natural observer. The rotor speed is estimated from the load torque, stator current, and rotor flux. Under symmetrical load conditions, the difference in speed between two induction motors is reduced by considering the motor parameters......This paper presents the characteristic behavior of direct vector control of two induction motors with sensorless speed feedback having the same rating parameters, paralleled combination, and supplied from a single current-controlled pulse-width-modulated voltage-source inverter drive. Natural...... observer design technique is known for its simple construction, which estimates the speed and rotor fluxes. Load torque is estimated by load torque adaptation and the average rotor flux was maintained constant by rotor flux feedback control. The technique’s convergence rate is very fast and is robust...

Visualization of high speed liquid jet impaction on a moving surface.

Science.gov (United States)

Guo, Yuchen; Green, Sheldon

2015-04-17

Two apparatuses for examining liquid jet impingement on a high-speed moving surface are described: an air cannon device (for examining surface speeds between 0 and 25 m/sec) and a spinning disk device (for examining surface speeds between 15 and 100 m/sec). The air cannon linear traverse is a pneumatic energy-powered system that is designed to accelerate a metal rail surface mounted on top of a wooden projectile. A pressurized cylinder fitted with a solenoid valve rapidly releases pressurized air into the barrel, forcing the projectile down the cannon barrel. The projectile travels beneath a spray nozzle, which impinges a liquid jet onto its metal upper surface, and the projectile then hits a stopping mechanism. A camera records the jet impingement, and a pressure transducer records the spray nozzle backpressure. The spinning disk set-up consists of a steel disk that reaches speeds of 500 to 3,000 rpm via a variable frequency drive (VFD) motor. A spray system similar to that of the air cannon generates a liquid jet that impinges onto the spinning disc, and cameras placed at several optical access points record the jet impingement. Video recordings of jet impingement processes are recorded and examined to determine whether the outcome of impingement is splash, splatter, or deposition. The apparatuses are the first that involve the high speed impingement of low-Reynolds-number liquid jets on high speed moving surfaces. In addition to its rail industry applications, the described technique may be used for technical and industrial purposes such as steelmaking and may be relevant to high-speed 3D printing.

Simulation and Implementation of Sensorless Control in Multi-Motors Electric Drives with High Dynamics

Directory of Open Access Journals (Sweden)

Marcel Nicola

2017-05-01

Full Text Available In this article we’ll tackle the control of multi-motors electric drives with high dynamic, with rapid changes in torque and speed, with rigid or flexible coupling of motors, where the control strategy is FOC (Field Oriented Control for each drives and the distributed control in local network using the CANopen protocol. In the surface mining industry, from which the electric drive application for this article is selected, the general trend is toward using asynchronous motors with short-circuit rotor, due to the advantages of this motor both in terms of design and operation. In order to achieve the variable speed, must be used the static frequency converters with sensorless control, where speed is estimated using a Model References Adaptive Control Estimator. The global control system proposed in this paper contain this type of MRAC estimator together with PI-control based, who ensures a good dynamic performance but in a lower complexity of structure such that are properly to implement in real time in a distributed control system with DSP in local network using the CANopen protocol with advantages in terms of software technology, as well as control cost and flexibility of use. Following these directions a functional application was implemented and tested in practice.

High-speed fan-beam reconstruction using direct two-dimensional Fourier transform method

International Nuclear Information System (INIS)

Niki, Noboru; Mizutani, Toshio; Takahashi, Yoshizo; Inouye, Tamon.

1984-01-01

Since the first development of X-ray computer tomography (CT), various efforts have been made to obtain high quality of high-speed image. However, the development of high resolution CT and the ultra-high speed CT to be applied to hearts is still desired. The X-ray beam scanning method was already changed from the parallel beam system to the fan-beam system in order to greatly shorten the scanning time. Also, the filtered back projection (DFBP) method has been employed to directly processing fan-beam projection data as reconstruction method. Although the two-dimensional Fourier transform (TFT) method significantly faster than FBP method was proposed, it has not been sufficiently examined for fan-beam projection data. Thus, the ITFT method was investigated, which first executes rebinning algorithm to convert the fan-beam projection data to the parallel beam projection data, thereafter, uses two-dimensional Fourier transform. By this method, although high speed is expected, the reconstructed images might be degraded due to the adoption of rebinning algorithm. Therefore, the effect of the interpolation error of rebinning algorithm on the reconstructed images has been analyzed theoretically, and finally, the result of the employment of spline interpolation which allows the acquisition of high quality images with less errors has been shown by the numerical and visual evaluation based on simulation and actual data. Computation time was reduced to 1/15 for the image matrix of 512 and to 1/30 for doubled matrix. (Wakatsuki, Y.)

The global lambda visualization facility: An international ultra-high-definition wide-area visualization collaboratory

Science.gov (United States)

Leigh, J.; Renambot, L.; Johnson, Aaron H.; Jeong, B.; Jagodic, R.; Schwarz, N.; Svistula, D.; Singh, R.; Aguilera, J.; Wang, X.; Vishwanath, V.; Lopez, B.; Sandin, D.; Peterka, T.; Girado, J.; Kooima, R.; Ge, J.; Long, L.; Verlo, A.; DeFanti, T.A.; Brown, M.; Cox, D.; Patterson, R.; Dorn, P.; Wefel, P.; Levy, S.; Talandis, J.; Reitzer, J.; Prudhomme, T.; Coffin, T.; Davis, B.; Wielinga, P.; Stolk, B.; Bum, Koo G.; Kim, J.; Han, S.; Corrie, B.; Zimmerman, T.; Boulanger, P.; Garcia, M.

2006-01-01

The research outlined in this paper marks an initial global cooperative effort between visualization and collaboration researchers to build a persistent virtual visualization facility linked by ultra-high-speed optical networks. The goal is to enable the comprehensive and synergistic research and development of the necessary hardware, software and interaction techniques to realize the next generation of end-user tools for scientists to collaborate on the global Lambda Grid. This paper outlines some of the visualization research projects that were demonstrated at the iGrid 2005 workshop in San Diego, California.

Electro-optic deflectors deliver advantages over acousto-optical deflectors in a high resolution, ultra-fast force-clamp optical trap.

Science.gov (United States)

Woody, Michael S; Capitanio, Marco; Ostap, E Michael; Goldman, Yale E

2018-04-30

We characterized experimental artifacts arising from the non-linear response of acousto-optical deflectors (AODs) in an ultra-fast force-clamp optical trap and have shown that using electro-optical deflectors (EODs) instead eliminates these artifacts. We give an example of the effects of these artifacts in our ultra-fast force clamp studies of the interaction of myosin with actin filaments. The experimental setup, based on the concept of Capitanio et al. [Nat. Methods 9, 1013-1019 (2012)] utilizes a bead-actin-bead dumbbell held in two force-clamped optical traps which apply a load to the dumbbell to move it at a constant velocity. When myosin binds to actin, the filament motion stops quickly as the total force from the optical traps is transferred to the actomyosin attachment. We found that in our setup, AODs were unsuitable for beam steering due to non-linear variations in beam intensity and deflection angle as a function of driving frequency, likely caused by low-amplitude standing acoustic waves in the deflectors. These aberrations caused instability in the force feedback loops leading to artifactual jumps in the trap position. We demonstrate that beam steering with EODs improves the performance of our instrument. Combining the superior beam-steering capability of the EODs, force acquisition via back-focal-plane interferometry, and dual high-speed FPGA-based feedback loops, we apply precise and constant loads to study the dynamics of interactions between actin and myosin. The same concept applies to studies of other biomolecular interactions.

High-speed imaging of explosive eruptions: applications and perspectives

Science.gov (United States)

Taddeucci, Jacopo; Scarlato, Piergiorgio; Gaudin, Damien; Capponi, Antonio; Alatorre-Ibarguengoitia, Miguel-Angel; Moroni, Monica

2013-04-01

explosion, with ejection velocities twice as high as previously recorded. Video-derived information on ejection velocity and ejecta mass can be combined with analytical and experimental models to constrain the physical parameters of the gas driving individual pulses. 2) Jet development. The ejection trajectory of pyroclasts can also be used to outline the spatial and temporal development of the eruptive jet and the dynamics of gas-pyroclast coupling within the jet, while high-speed thermal images add information on the temperature evolution in the jet itself as a function of the pyroclast size and content. 2) Pyroclasts settling. High-speed videos can be used to investigate the aerodynamic settling behavior of pyroclasts from bomb to ash in size and including ash aggregates, providing key parameters such as drag coefficient as a function of Re, and particle density. 3) The generation and propagation of acoustic and shock waves. Phase condensation in volcanic and atmospheric aerosol is triggered by the transit of pressure waves and can be recorded in high-speed videos, allowing the speed and wavelength of the waves to be measured and compared with the corresponding infrasonic signals and theoretical predictions.

Ultra-high resolution protein crystallography

International Nuclear Information System (INIS)

Takeda, Kazuki; Hirano, Yu; Miki, Kunio

2010-01-01

Many protein structures have been determined by X-ray crystallography and deposited with the Protein Data Bank. However, these structures at usual resolution (1.5< d<3.0 A) are insufficient in their precision and quantity for elucidating the molecular mechanism of protein functions directly from structural information. Several studies at ultra-high resolution (d<0.8 A) have been performed with synchrotron radiation in the last decade. The highest resolution of the protein crystals was achieved at 0.54 A resolution for a small protein, crambin. In such high resolution crystals, almost all of hydrogen atoms of proteins and some hydrogen atoms of bound water molecules are experimentally observed. In addition, outer-shell electrons of proteins can be analyzed by the multipole refinement procedure. However, the influence of X-rays should be precisely estimated in order to derive meaningful information from the crystallographic results. In this review, we summarize refinement procedures, current status and perspectives for ultra high resolution protein crystallography. (author)

Application of the voltage biased digital relay for the optimal protection of high inertia drive induction motors

International Nuclear Information System (INIS)

Choi, D. B.

1999-01-01

This paper describes typical protection schemes for large-size high inertia drive motor that are generally rotor thermal limited. Difficult and variable starting conditions of the large-size high inertia drive motor and compromises in the selection and setting of the protective devices are frequently encountered. The motors that typically encounter severe starting duty and present difficulties in achieving full motor protection are reactor coolant pumps (RCPs), blowers and compressors. For difficult starting conditions that are encountered by the large-size high inertia drive motors, state-of-the-art computer based calculations are capable of providing realistic predictions of the band of margin available for applying the protective relay. Based on the analysis of starting characteristics of large-size high inertia drive motors, this paper recommends that the optimal protection scheme for high inertia drive motors for nuclear power plants can be achieved by using the voltage biased digital relay instead of a speed switch and conventional overcurrent relays. (author)

Inverter fed high-speed solid-rotor induction motors for industrial applications

Energy Technology Data Exchange (ETDEWEB)

Huppunen, J.; Pyrhoenen, J. [Lappeenranta Univ. of Technology (LUT) (Finland); Alamaeki, J. [Rotatek Finland Oy, Lappeenranta (Finland)

2000-07-01

An inverter fed 250 kW, 9000 min{sup -1} solid-rotor induction motor drive for an industrial compressor application is introduced. New designing methods for the electric motor have made it possible to create a high efficiency high-speed solid-rotor induction motor. The results of the research work are new motor structures that are also easy and economical to manufacture. This technology is very reliable and economical for compressor and pump applications in power range from 100 kW to 1000 kW. (orig.)

Development of Propulsion Inverter Control System for High-Speed Maglev based on Long Stator Linear Synchronous Motor

Directory of Open Access Journals (Sweden)

Jeong-Min Jo

2017-02-01

Full Text Available In the case of a long-stator linear drive, unlike rotative drives for which speed or position sensors are a single unit attached to the shaft, these sensors extend along the guideway. The position signals transmitted from a maglev vehicle cannot meet the need of the real-time propulsion control in the on-ground inverter power substations. In this paper the design of the propulsion inverter control system with a position estimator for driving a long-stator synchronous motor in a high-speed maglev train is proposed. The experiments have been carried out at the 150 m long guideway at the O-song test track. To investigate the performance of the position estimator, the propulsion control system with, and without, the position estimator are compared. The result confirms that the proposed strategy can meet the dynamic property needs of the propulsion inverter control system for driving long-stator linear synchronous motors.

Concepts for Multi-Speed Rotorcraft Drive System - Status of Design and Testing at NASA GRC

Science.gov (United States)

Stevens, Mark A.; Lewicki, David G.; Handschuh, Robert F.

2015-01-01

In several studies and on-going developments for advanced rotorcraft, the need for variable/multi-speed capable rotors has been raised. Speed changes of up to 50 percent have been proposed for future rotorcraft to improve vehicle performance. A rotor speed change during operation not only requires a rotor that can perform effectively over the operating speed/load range, but also requires a propulsion system possessing these same capabilities. A study was completed investigating possible drive system arrangements that can accommodate up to a 50 percent speed change. Key drivers were identified from which simplicity and weight were judged as central. This paper presents the current status of two gear train concepts coupled with the first of two clutch types developed and tested thus far with focus on design lessons learned and areas requiring development. Also, a third concept is presented, a dual input planetary differential as leveraged from a simple planetary with fixed carrier.

Divergent plate motion drives rapid exhumation of (ultra)high pressure rocks

Science.gov (United States)

Liao, Jie; Malusà, Marco G.; Zhao, Liang; Baldwin, Suzanne L.; Fitzgerald, Paul G.; Gerya, Taras

2018-06-01

Exhumation of (ultra)high pressure [(U)HP] rocks by upper-plate divergent motion above an unbroken slab, first proposed in the Western Alps, has never been tested by numerical methods. We present 2D thermo-mechanical models incorporating subduction of a thinned continental margin beneath either a continental or oceanic upper plate, followed by upper-plate divergent motion away from the lower plate. Results demonstrate how divergent plate motion may trigger rapid exhumation of large volumes of (U)HP rocks directly to the Earth's surface, without the need for significant overburden removal by erosion. Model exhumation paths are fully consistent with natural examples for a wide range of upper-plate divergence rates. Exhumation rates are systematically higher than the divergent rate imposed to the upper plate, and the modeled size of exhumed (U)HP domes is invariant for different rates of upper-plate divergence. Major variations are instead predicted at depth for differing model scenarios, as larger amounts of divergent motion may allow mantle-wedge exhumation to shallow depth under the exhuming domes. The transient temperature increase, due to ascent of mantle-wedge material in the subduction channel, has a limited effect on exhumed continental (U)HP rocks already at the surface. We test two examples, the Cenozoic (U)HP terranes of the Western Alps (continental upper plate) and eastern Papua New Guinea (oceanic upper plate). The good fit between model predictions and the geologic record in these terranes encourages the application of these models globally to pre-Cenozoic (U)HP terranes where the geologic record of exhumation is only partly preserved.

Low velocity impact behaviour of ultra high strength concrete panels

Indian Academy of Sciences (India)

Ultra high strength concrete; panel; drop weight test; impact analysis;. ABAQUS. 1. Introduction. Ultra high strength concrete ... Knight (2012) investigated the dynamic behaviour of steel fibre reinforced concrete plates under impact loading with ...

Fast response Antiwindup PI speed controller of Brushless DC motor drive: Modeling, simulation and implementation on DSP

Directory of Open Access Journals (Sweden)

Mohd Tariq

2016-05-01

Full Text Available Most of the Brushless DC (BLDC motors drive adopts proportional, integral and derivative (PID controller and pulse width modulation (PWM scheme for speed control. Hence, BLDC motor drive has strong saturation characteristics. The saturation results in a typical windup phenomenon. The paper presents an Antiwindup drive for BLDC motor. An Antiwindup controller (AWC has been used in the paper. AWC has been modeled in MATLAB/Simulink and comparison has been done between conventional PI controller and AWC at different starting loads. Dynamic characteristics of the BLDC motor drive have been examined and results are presented and discussed in detail in this paper. Details of DSP based experimental validation of the simulated results are also presented here.

Effect of Stand-Off Distance on Impact Pressure of High Speed Water Jets

Science.gov (United States)

Sittiwong, Wuttichai; Seehanam, Wirapan; Pianthong, Kulachate; Matthujak, Anirut

2010-06-01

High speed liquid jets may be applied to jet cutting, drilling and cleaning. Recently, in the automotive industries, the spray injection pressure becomes higher and higher to enhance the fuel mixing for the improved combustion efficiency. However, the ultra high injection pressure may cause the damage to the nozzle and also the combustion chamber. In the medical application, the high speed liquid injection might be applied for the drug delivery through the skin where the needle is not required anymore. From the above mentioned application, the investigation on the impact pressure of the high speed liquid jet relative to the stand-off distant is significant. The high speed liquid jets are generated by the projectile impact driven method. The high speed projectile is launched by the horizontal single stage powder gun. The experimental study focuses on the stand-off between 1.5 cm to 6.0 cm, while the nozzle contains approximately 1.5cm3 of water in its cavity. The nozzle conical angles are 30° and 60° with the orifice diameter of 0.7 mm. The jet velocities are measured by laser beam interruptions method. The target material is the Polymethyl Methacrylate (PMMA) which the impact pressure is measured by using a piezoelectric Polyvinylidene Fluoride (PVDF) film. From the experiments, the maximum water jet velocity of 2290 m/s can be obtained from the 30° conical angle nozzle. The maximum impact pressures of nozzle conical angle of 30° and 60° are 3.4 GPa and 2.6 GPa respectively, at stand-off distance 3 cm. However, at the stand-off distance more than 3 cm, the impact pressure significantly decreases, because of aerodynamic drag, jets core break-up, and atomization of the water.

Nonlinear Speed Control of Switched Reluctance Motor Drives Taking into Account Mutual Inductance

Directory of Open Access Journals (Sweden)

M. Rayan

2008-03-01

Full Text Available A speed control algorithm is proposed for variable speed switched reluctance motor (SRM drives taking into account the effects of mutual inductances. The control scheme adopts two-phase excitation; exciting two adjacent phases can overcome the problems associated with single-phase excitation such as large torque ripple, increased acoustic noise, and rotor shaft fatigues. The effects of mutual coupling between two adjacent phases and their contribution to the generated electromagnetic torque are considered in the design of the proposed control scheme for the motor. The proposed controller guarantees the convergence of the currents and the rotor speed of the motor to their desired values. Simulation results are given to illustrate the developed theory; the simulation studies show that the proposed controller works well. Moreover, the simulation results indicate that the proposed controller is robust to changes in the parameters of the motor and to changes in the load torque.

Precision increase in electric drive speed loop of robotic complexes and process lines

Science.gov (United States)

Tulegenov, E.; Imanova, A. A.; Platonov, V. V.

2018-05-01

The article presents the principles of synthesis of control structures for highprecision electric drives of robotic complexes and manipulators. It has been theoretically shown and experimentally confirmed that improved characteristics of speed maintenance in the zone of significant overloads are achieved in systems of series excitation. They are achieved due to the redistribution of control signals both in the zone of setting the armature current and in the excitation currents. At the same time, the characteristic of the electromagnetic torque becomes linear because the demagnetizing effect of the armature response is compensated by the setting of the excitation current. It is recommended in those cases when it is necessary to extend the range of speed control with a significant reduction in load to apply structures with two-zone speed control. The regulation of the weakening of the excitation flow is more convenient as a function of the voltage in the armature windings.

Investigation on Electromagnetic Models of High-Speed Solenoid Valve for Common Rail Injector

Directory of Open Access Journals (Sweden)

Jianhui Zhao

2017-01-01

Full Text Available A novel formula easily applied with high precision is proposed in this paper to fit the B-H curve of soft magnetic materials, and it is validated by comparison with predicted and experimental results. It can accurately describe the nonlinear magnetization process and magnetic saturation characteristics of soft magnetic materials. Based on the electromagnetic transient coupling principle, an electromagnetic mathematical model of a high-speed solenoid valve (HSV is developed in Fortran language that takes the saturation phenomena of the electromagnetic force into consideration. The accuracy of the model is validated by the comparison of the simulated and experimental static electromagnetic forces. Through experiment, it is concluded that the increase of the drive current is conducive to improving the electromagnetic energy conversion efficiency of the HSV at a low drive current, but it has little effect at a high drive current. Through simulation, it is discovered that the electromagnetic energy conversion characteristics of the HSV are affected by the drive current and the total reluctance, consisting of the gap reluctance and the reluctance of the iron core and armature soft magnetic materials. These two influence factors, within the scope of the different drive currents, have different contribution rates to the electromagnetic energy conversion efficiency.

Introducing a multivariate model for predicting driving performance: the role of driving anger and personal characteristics.

Science.gov (United States)

Roidl, Ernst; Siebert, Felix Wilhelm; Oehl, Michael; Höger, Rainer

2013-12-01

Maladaptive driving is an important source of self-inflicted accidents and this driving style could include high speeds, speeding violations, and poor lateral control of the vehicle. The literature suggests that certain groups of drivers, such as novice drivers, males, highly motivated drivers, and those who frequently experience anger in traffic, tend to exhibit more maladaptive driving patterns compared to other drivers. Remarkably, no coherent framework is currently available to describe the relationships and distinct influences of these factors. We conducted two studies with the aim of creating a multivariate model that combines the aforementioned factors, describes their relationships, and predicts driving performance more precisely. The studies employed different techniques to elicit emotion and different tracks designed to explore the driving behaviors of participants in potentially anger-provoking situations. Study 1 induced emotions with short film clips. Study 2 confronted the participants with potentially anger-inducing traffic situations during the simulated drive. In both studies, participants who experienced high levels of anger drove faster and exhibited greater longitudinal and lateral acceleration. Furthermore, multiple linear regressions and path-models revealed that highly motivated male drivers displayed the same behavior independent of their emotional state. The results indicate that anger and specific risk characteristics lead to maladaptive changes in important driving parameters and that drivers with these specific risk factors are prone to experience more anger while driving, which further worsens their driving performance. Driver trainings and anger management courses will profit from these findings because they help to improve the validity of assessments of anger related driving behavior. © 2013.

Radiobiological response to ultra-short pulsed megavoltage electron beams of ultra-high pulse dose rate.

Science.gov (United States)

Beyreuther, Elke; Karsch, Leonhard; Laschinsky, Lydia; Leßmann, Elisabeth; Naumburger, Doreen; Oppelt, Melanie; Richter, Christian; Schürer, Michael; Woithe, Julia; Pawelke, Jörg

2015-08-01

In line with the long-term aim of establishing the laser-based particle acceleration for future medical application, the radiobiological consequences of the typical ultra-short pulses and ultra-high pulse dose rate can be investigated with electron delivery. The radiation source ELBE (Electron Linac for beams with high Brilliance and low Emittance) was used to mimic the quasi-continuous electron beam of a clinical linear accelerator (LINAC) for comparison with electron pulses at the ultra-high pulse dose rate of 10(10) Gy min(-1) either at the low frequency of a laser accelerator or at 13 MHz avoiding effects of prolonged dose delivery. The impact of pulse structure was analyzed by clonogenic survival assay and by the number of residual DNA double-strand breaks remaining 24 h after irradiation of two human squamous cell carcinoma lines of differing radiosensitivity. The radiation response of both cell lines was found to be independent from electron pulse structure for the two endpoints under investigation. The results reveal, that ultra-high pulse dose rates of 10(10) Gy min(-1) and the low repetition rate of laser accelerated electrons have no statistically significant influence (within the 95% confidence intervals) on the radiobiological effectiveness of megavoltage electrons.

Load Torque Compensator for Model Predictive Direct Current Control in High Power PMSM Drive Systems

DEFF Research Database (Denmark)

Preindl, Matthias; Schaltz, Erik

2010-01-01

In drive systems the most used control structure is the cascade control with an inner torque, i.e. current and an outer speed control loop. The fairly small converter switching frequency in high power applications, e.g. wind turbines lead to modest speed control performance. An improvement bring...... the use of a current controller which takes into account the discrete states of the inverter, e.g. DTC or a more modern approach: Model Predictive Direct Current Control (MPDCC). Moreover overshoots and oscillations in the speed are not desired in many applications, since they lead to mechanical stress...

Optimisation of hybrid high-modulus/high-strength carbon fiber reinforced plastic composite drive

OpenAIRE

Montagnier, Olivier; Hochard, Christian

2011-01-01

International audience; This study deals with the optimisation of hybrid composite drive shafts operating at subcritical or supercritical speeds, using a genetic algorithm. A formulation for the flexural vibrations of a composite drive shaft mounted on viscoelastic supports including shear effects is developed. In particular, an analytic stability criterion is developed to ensure the integrity of the system in the supercritical regime. Then it is shown that the torsional strength can be compu...

High accuracy microwave frequency measurement based on single-drive dual-parallel Mach-Zehnder modulator

DEFF Research Database (Denmark)

Zhao, Ying; Pang, Xiaodan; Deng, Lei

2011-01-01

A novel approach for broadband microwave frequency measurement by employing a single-drive dual-parallel Mach-Zehnder modulator is proposed and experimentally demonstrated. Based on bias manipulations of the modulator, conventional frequency-to-power mapping technique is developed by performing a...... 10−3 relative error. This high accuracy frequency measurement technique is a promising candidate for high-speed electronic warfare and defense applications....

High speed ultra-broadband amplitude modulators with ultrahigh extinction >65 dB.

Science.gov (United States)

Liu, S; Cai, H; DeRose, C T; Davids, P; Pomerene, A; Starbuck, A L; Trotter, D C; Camacho, R; Urayama, J; Lentine, A

2017-05-15

We experimentally demonstrate ultrahigh extinction ratio (>65 dB) amplitude modulators (AMs) that can be electrically tuned to operate across a broad spectral range of 160 nm from 1480 - 1640 nm and 95 nm from 1280 - 1375 nm. Our on-chip AMs employ one extra coupler compared with conventional Mach-Zehnder interferometers (MZI), thus form a cascaded MZI (CMZI) structure. Either directional or adiabatic couplers are used to compose the CMZI AMs and experimental comparisons are made between these two different structures. We investigate the performance of CMZI AMs under extreme conditions such as using 95:5 split ratio couplers and unbalanced waveguide losses. Electro-optic phase shifters are also integrated in the CMZI AMs for high-speed operation. Finally, we investigate the output optical phase when the amplitude is modulated, which provides us valuable information when both amplitude and phase are to be controlled. Our demonstration not only paves the road to applications such as quantum information processing that requires high extinction ratio AMs but also significantly alleviates the tight fabrication tolerance needed for large-scale integrated photonics.

Field-tested technology for gas compression: using high-speed induction motors to replace conventional solutions

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, Karina Velloso; Pradurat, Jean Francois [Institut National Polytechnique de Lorraine (INPL), Nancy (France). Converteam Rotating Machines Division

2009-07-01

Industry leaders are all concerned about rationalization of electric power use, increase of efficiency and flexibility, environmental impact, installations size and maintenance efforts diminution. The high-speed induction motors are a good solution when addressing these parameters. How this technology works and how using it can help pipelines operators meet growing operational and environmental challenges is the main subject of this paper, that also explain how it can be used to replace conventional solutions. As a conclusion the future opportunities of electric high-speed drive systems application in production, transport and storage for natural gas industry are going to be discussed. (author)

Fifteen Years of Operation at NASA's National Transonic Facility with the World's Largest Adjustable Speed Drive

Science.gov (United States)

Sydnor, George H.; Bhatia, Ram; Krattiger, Hansueli; Mylius, Justus; Schafer, D.

2012-01-01

In September 1995, a project was initiated to replace the existing drive line at NASA's most unique transonic wind tunnel, the National Transonic Facility (NTF), with a single 101 MW synchronous motor driven by a Load Commutated Inverter (LCI). This Adjustable Speed Drive (ASD) system also included a custom four-winding transformer, harmonic filter, exciter, switch gear, control system, and feeder cable. The complete system requirements and design details have previously been presented and published [1], as well as the commissioning and acceptance test results [2]. The NTF was returned to service in December 1997 with the new drive system powering the fan. Today, this installation still represents the world s largest horizontal single motor/drive combination. This paper describes some significant events that occurred with the drive system during the first 15 years of service. These noteworthy issues are analyzed and root causes presented. Improvements that have substantially increased the long term viability of the system are given.

Ultra-high energy cosmic rays from white dwarf pulsars and the Hillas criterion

International Nuclear Information System (INIS)

Lobato, Ronaldo V.; Coelho, Jaziel G.; Malheiro, M.

2017-01-01

The origins of ultra-high-energy cosmic rays ( E ≳ 10 19 eV) are a mystery and still under debate in astroparticle physics. In recent years some efforts were made to understand their nature. In this contribution we consider the possibility of Some Soft Gamma Repeaters (SGRs) and Anomalous X-ray Pulsars (AXPs) beeing white dwarf pulsars, and show that these sources can achieve large electromagnetic potentials on their surface that accelerate particle almost at the speed of light, with energies E ∼ 10 20-21 eV. The sources SGRs/AXPs considered as highly magnetized white dwarfs are well described in the Hillas diagram, lying close to the AR Sorpii and AE Aquarii which are understood as white dwarf pulsars. (paper)

INFLUENCE ANALYSES OF DESIGNED CHARACTERISTICS OF THE ELEVATOR TO THE PARAMETERS OF ITS DRIVE

Directory of Open Access Journals (Sweden)

V. M. Bohomaz

2015-04-01

Full Text Available Purpose. A drive behaves to the basic elements of scoop band elevators. To determine the drive power calculations are carried out according to standard methods, which take plenty of time. It is necessary to conduct the analysis of influence of project characteristics on the parameters of high-speed drive in a scoop bent elevator and to build the improved algorithm of speed-up determination of its drive power on project descriptions, that will take into account the type of load, rise height, necessary productivity, standard parameters of scoops and tape. Methodology. Using parametric dependences of elevators drive power on its project characteristics, received by the author earlier, the improved algorithm of speed-up determination of elevators high-speed drive power with deep and shallow scoops at set type of load, productivity, rise height was offered. Findings. The algorithm of drive power speed-up determination of high-speed vertical elevators with deep and shallow scoops depending on project parameters was offered. The example of such algorithm application is considered for an elevator that is intended for transporting of cement. Analytical dependences of drive power of such elevator are determined on the productivity and rise height. Corresponding graphic dependences were built and character of drive power changes during the size changing of any project characteristics was determined. Originality. The improved algorithm of drive power elevator determination at the given project characteristics (type of load, rise height, productivity that takes into account standard sizes, parameters of scoops and ribbons, was built at first time. Practical value. The use of an offered algorithm of calculation gives the possibility of relatively fast determination of reference value of high-speed elevators drive power with deep and shallow scoops, to build graphic dependences of drive power on the values of the productivity and rise height at the certain

A Review of Electronic Inductor Technique for Power Factor Correction in Three-Phase Adjustable Speed Drives

DEFF Research Database (Denmark)

Davari, Pooya; Yang, Yongheng; Zare, Firuz

2016-01-01

(SiC) power devices. Moreover, the influence of partial loading on component sizing in Adjustable Speed Drives (ASDs) is studied. Finally the analytical loss modelling of power switches is utilized for efficiency measurement. The theoretical analyses are verified by experimental benchmarking in an ASD...

Enhanced Phase-Shifted Current Control for Harmonic Cancellation in Three-Phase Multiple Adjustable Speed Drive Systems

DEFF Research Database (Denmark)

Yang, Yongheng; Davari, Pooya; Zare, Firuz

2017-01-01

A phase-shifted current control can be employed to mitigate certain harmonics induced by the Diode Rectifiers (DR) and Silicon-Controlled Rectifiers (SCR) as the front-ends of multiple parallel Adjustable Speed Drive (ASD) systems. However, the effectiveness of the phase-shifted control relies...... on the loading condition of each drive unit as well as the number of drives in parallel. In order to enhance the harmonic cancellation by means of the phase-shifted current control, the currents drawn by the rectifiers should be maintained almost at the same level. Thus, this paper firstly analyzes the impact...... of unequal loading among the parallel drives, and a scheme to enhance the performance is introduced to improve the quality of the total grid current, where partial loading operation should be enabled. Simulation and experimental case studies on multidrive systems have demonstrated that the enhanced phase...

Stated response to increased enforcement density and penalty size for speeding and driving unbelted.

Science.gov (United States)

Hössinger, Reinhard; Berger, Wolfgang J

2012-11-01

To what extent can traffic offences be reduced through stronger enforcement, higher penalties, and the provision of information to road users? This question was addressed with respect to the offences of "speeding" and "driving unbelted." Data were collected by a telephone survey of admitted speeders, followed by 438 face-to-face stated response interviews. Based on the data collected, separate statistical models were developed for the two offences. The models predict the behavioral effect of increasing enforcement density and/or penalty size as well as the additional effect of providing information to car drivers. All three factors are predicted to be effective in reducing speeding. According to the model, one additional enforcement event per year will cause a driver to reduce his current frequency of speeding by 5%. A penalty increase of 10 Euros is predicted to have the same effect. An announcement of stronger enforcement or higher fines is predicted to have an additional effect on behavior, independent of the actual magnitudes of increase in enforcement or fines. With respect to the use of a seat belt, however, neither an increase in enforcement density nor its announcement is predicted to have a significant effect on driver behavior. An increase in the penalty size is predicted to raise the stated wearing rate, which is already 90% in Austria. It seems that both the fear of punishment and the motivation for driving unbelted are limited, so that there is only a weak tradeoff between the two. This may apply to most traffic offences, with the exception of speeding, which accounts for over 80% of tickets alone, whereas all other offences account for less than 3% each. Copyright © 2012 Elsevier Ltd. All rights reserved.

Examining speed of processing of facial emotion recognition in individuals at ultra-high risk for psychosis

DEFF Research Database (Denmark)

Glenthøj, Louise Birkedal; Fagerlund, Birgitte; Bak, Nikolaj

2018-01-01

Emotion recognition is an aspect of social cognition that may be a key predictor of functioning and transition to psychosis in individuals at ultra-high risk (UHR) for psychosis ( Allott et al., 2014 ). UHR individuals exhibit deficits in accurately identifying facial emotions ( van Donkersgoed et...... al., 2015 ), but other potential anomalies in facial emotion recognition are largely unexplored. This study aimed to extend current knowledge on emotion recognition deficits in UHR individuals by examining: 1) whether UHR would display significantly slower facial emotion recognition than healthy...... controls, 2) whether an association between emotion recognition accuracy and emotion recognition latency is present in UHR, 3) the relationships between emotion recognition accuracy, neurocognition and psychopathology in UHR....

Electric drives

Energy Technology Data Exchange (ETDEWEB)

1986-10-01

Several electric vehicles have been tested in long-term tests, i.e. an electric passenger car (maximum speed 115 km/h) and several busses for use in pedestrians' zones, spas, airports, natural reserves, and urban transportation (DUO busses). The ICE high-speed train is discussed in some detail, i.e. its aeroacoustic and aerodynamic design, running gear, computer-controlled drives and brakes, diagnostic systems, and electrical equipment. The Berlin Maglev system is mentioned as well as current inverters in rail vehicles. (HWJ).

Two-Phase Induction Motor Drives

Directory of Open Access Journals (Sweden)

Gholam Reza Arab Markadeh

2010-10-01

Full Text Available The lack of variable-speed drives for two (single induction motor is a reality. This article attempts mainly to investigate the reasons for this lack of variable – speed drives. This paper deals with literature survey of various existing converter topologies, which have been proposed for adjustable speed single phase induction motor drives. Various converter topologies have been compared in this paper. Among these converter topologies, the adjustable frequency PWM inverter is the best choice for single-phase induction motor drives. However, adjustable-frequency drives have not been widely used with single-phase Induction motors. The open-loop constant V/F control law cannot be used with the single-phase induction motor drives as it is used with three phase motors. The variation of the operating frequency at lower speed range with constant load torque causes variation in motor's slip. A constant V/F control is suitable only over the upper speed range.

A low-cost, ultra-fast and ultra-low noise preamplifier for silicon avalanche photodiodes

Science.gov (United States)

Gasmi, Khaled

2018-02-01

An ultra-fast and ultra-low noise preamplifier for amplifying the fast and weak electrical signals generated by silicon avalanche photodiodes has been designed and developed. It is characterized by its simplicity, compactness, reliability and low cost of construction. A very wide bandwidth of 300 MHz, a very good linearity from 1 kHz to 280 MHz, an ultra-low noise level at the input of only 1.7 nV Hz-1/2 and a very good stability are its key features. The compact size (70 mm  ×  90 mm) and light weight (45 g), as well as its excellent characteristics, make this preamplifier very competitive compared to any commercial preamplifier. The preamplifier, which is a main part of the detection system of a homemade laser remote sensing system, has been successfully tested. In addition, it is versatile and can be used in any optical detection system requiring high speed and very low noise electronics.

New solid laser: Ceramic laser. From ultra stable laser to ultra high output laser

International Nuclear Information System (INIS)

Ueda, Kenichi

2006-01-01

An epoch-making solid laser is developed. It is ceramic laser, polycrystal, which is produced as same as glass and shows ultra high output. Ti 3+ :Al 2 O 3 laser crystal and the CPA (chirped pulse amplification) technique realized new ultra high output lasers. Japan has developed various kinds of ceramic lasers, from 10 -2 to 67 x 10 3 w average output, since 1995. These ceramic lasers were studied by gravitational radiation astronomy. The scattering coefficient of ceramic laser is smaller than single crystals. The new fast ignition method is proposed by Institute of Laser Engineering of Osaka University, Japan. Ultra-intense short pulse laser can inject the required energy to the high-density imploded core plasma within the core disassembling time. Ti 3+ :Al 2 O 3 crystal for laser, ceramic YAG of large caliber for 100 kW, transparent laser ceramic from nano-crystals, crystal grain and boundary layer between grains, the scattering coefficient of single crystal and ceramic, and the derived release cross section of Yb:YAG ceramic are described. (S.Y.)

Ultra-high wear resistance of ultra-nanocrystalline diamond film: Correlation with microstructure and morphology

Science.gov (United States)

Rani, R.; Kumar, N.; Lin, I.-Nan

2016-05-01

Nanostructured diamond films are having numerous unique properties including superior tribological behavior which is promising for enhancing energy efficiency and life time of the sliding devices. High wear resistance is the principal criterion for the smooth functioning of any sliding device. Such properties are achievable by tailoring the grain size and grain boundary volume fraction in nanodiamond film. Ultra-nanocrystalline diamond (UNCD) film was attainable using optimized gas plasma condition in a microwave plasma enhanced chemical vapor deposition (MPECVD) system. Crystalline phase of ultra-nanodiamond grains with matrix phase of amorphous carbon and short range ordered graphite are encapsulated in nanowire shaped morphology. Film showed ultra-high wear resistance and frictional stability in micro-tribological contact conditions. The negligible wear of film at the beginning of the tribological contact was later transformed into the wearless regime for prolonged sliding cycles. Both surface roughness and high contact stress were the main reasons of wear at the beginning of sliding cycles. However, the interface gets smoothened due to continuous sliding, finally leaded to the wearless regime.

Rotor-dynamic design aspects for a variable frequency drive based high speed cryogenic centrifugal pump in fusion devices

International Nuclear Information System (INIS)

Das, Jotirmoy; Vaghela, Hitensinh; Bhattacharya, Ritendra; Patel, Pratik; Shukla, Vinit; Shah, Nitin; Sarkar, Biswanath

2015-01-01

Superconducting magnets of large size are inevitable for fusion devices due to high magnetic field requirements. Forced flow cooling of the superconducting magnets with high mass flowrate of the order ∼3 kg/s is required to keep superconducting magnets within its safe operational boundaries during various plasma scenarios. This important requirement can be efficiently fulfilled by employing high capacity and high efficiency cryogenic centrifugal pumps. The efficiency > 70% will ensure overall lower heat load to the cryoplant. Thermo-hydraulic design of cryogenic centrifugal pump revealed that to achieve the operational regime with high efficiency, the speed should be ∼ 10,000 revolutions per minute. In this regard, the rotor-dynamic design aspect is quite critical from the operational stability point of view. The rotor shaft design of the cryogenic pump is primarily an outcome of optimization between thermal heat-in leak at cryogenic temperature level from ambient, cryogenic fluid impedance and designed rotation speed of the impeller wheel. The paper describes the basic design related to critical speed of the rotor shaft, rotor whirl and system instability prediction to explore the ideal operational range of the pump from the system stability point of view. In the rotor-dynamic analysis, the paper also describes the Campbell plots to ensure that the pump is not disturbed by any of the critical speeds, especially while operating near the nominal and enhanced operating modes. (author)

A New High-Speed, High-Cycle, Gear-Tooth Bending Fatigue Test Capability

Science.gov (United States)

Stringer, David B.; Dykas, Brian D.; LaBerge, Kelsen E.; Zakrajsek, Andrew J.; Handschuh, Robert F.

2011-01-01

A new high-speed test capability for determining the high cycle bending-fatigue characteristics of gear teeth has been developed. Experiments were performed in the test facility using a standard spur gear test specimens designed for use in NASA Glenn s drive system test facilities. These tests varied in load condition and cycle-rate. The cycle-rate varied from 50 to 1000 Hz. The loads varied from high-stress, low-cycle loads to near infinite life conditions. Over 100 tests were conducted using AISI 9310 steel spur gear specimen. These results were then compared to previous data in the literature for correlation. Additionally, a cycle-rate sensitivity analysis was conducted by grouping the results according to cycle-rate and comparing the data sets. Methods used to study and verify load-path and facility dynamics are also discussed.

Ultra-High Speed Visualization of the Flashing Instability in Micron Size Nozzles under Vacuum Conditions

KAUST Repository

Alghamdi, Tariq A.

2017-11-01

I visualized the flash-boiling atomization of liquid jets released into a low pressure environment at frame rates of up to five million frames per second. Such a high temporal resolution allowed us to observe for the first time the bubble expansion mechanism that atomizes the jet. To visualize the dynamics in detail, I focused closely to the outflow of the nozzle using a long distance microscope objective. I documented an abrupt transition from a laminar to a fully external flashing jet by systematically reducing the ambient pressure. I performed experiments with different volatile liquids and using nozzles with different inner diameters. The inner diameters of the nozzles varied from 30 to 480 . Perfluorohexane (PFnH) was our main working fluid, but also methanol, ethanol and 1-bromopropane were tested. Surprisingly, minimum intensity profiles revealed spray angles close to ~360°, meaning drops are ejected in all directions. Also, I measured speeds of bubble expansion up to 140 m/s. That is 45 times faster than the upper bound for inertial growth speed in complete vacuum from the Rayleigh-Plesset equation. I also calculated the trajectories of the ejected droplets as well as the drop speed distribution using particle tracking. I expect that our results bring new insight into the flash-boiling atomization mechanism.

Improving homogeneity by dynamic speed limit systems.

NARCIS (Netherlands)

Nes, N. van Brandenberg, S. & Twisk, D.A.M.

2010-01-01

Homogeneity of driving speeds is an important variable in determining road safety; more homogeneous driving speeds increase road safety. This study investigates the effect of introducing dynamic speed limit systems on homogeneity of driving speeds. A total of 46 subjects twice drove a route along 12

Expectations for ultra-high energy interactions

International Nuclear Information System (INIS)

Feynman, R.P.

1978-01-01

Strong interactions at ultra-high energies are discussed with emphasis on the hadrons produced in high energy collisions. Evidence is considered that quantum chromodynamics might be the right theory, and also some estimates are given of quantum chromodynamics asymptotic-freedom phenomena, the work under discussion being very preliminary. 6 references

Experimental research on the effectiveness and adaptability of speed reduction markings in downhill sections on urban roads: a driving simulation study.

Science.gov (United States)

Ding, Han; Zhao, Xiaohua; Rong, Jian; Ma, Jianming

2015-02-01

The objective of this paper is to test the effectiveness and adaptability of speed reduction markings (SRMs) in downhill sections on urban roads with distinct roadway grades. Empirical data including vehicle speed and acceleration were collected in a driving simulator. Subjective questionnaires were conducted, and two indexes - the relative speed difference and standard deviation of acceleration - were developed to evaluate the effectiveness and adaptability of SRMs. Meanwhile, the effectiveness of driving simulator related to different road alignments and types of SRMs has been validated through a field test. Results of subjective questionnaires showed that the majority of subjects had no feelings of nervousness, but they were affected by SRMs while driving through downhill sections in all four scenarios (i.e., downhill sections with vertical grades of 3, 2, 1.5 and 1%). In terms of vehicle speed and acceleration, the results of the analysis of variance (ANOVA) and the contrast analysis (S-N-K method) indicated that SRMs were significantly effective when roadway grades of downgrade sections were 1.5, 2 and 3%, while transverse speed reduction markings (TSRMs) had significantly worse adaptability (P<0.05). Therefore, this research recommends that TSRMs could be placed in downhill sections with roadway grades of 1.5 or 2%; longitudinal speed reduction markings (LSRMs) could be placed in downhill sections with a roadway grade of 3%. Whether SRMs are placed in downhill sections with a roadway grade of 1% would depend on other factors such as financial issues and crash records, which are not considered in this paper. Copyright © 2014 Elsevier Ltd. All rights reserved.

Extending ultra-short pulse laser texturing over large area

Energy Technology Data Exchange (ETDEWEB)

Mincuzzi, G., E-mail: girolamo.mincuzzi@alphanov.com; Gemini, L.; Faucon, M.; Kling, R.

2016-11-15

Highlights: • We carried out metal surface texturing (Ripples, micro grooves, Spikes) using a high power, high repetition rate, industrial, Ultra-short pulses laser. • Extremely Fast processing is shown (Laser Scan speed as high as 90 m/s) with a polygon scanner head. • Stainless steel surface blackening with Ultra-short pulses laser has been obtained with unprecedented scanspeed. • Full SEM surface characterization was carried out for all the different structures obtained. • Reflectance measurements were carried out to characterize surface reflectance. - Abstract: Surface texturing by Ultra-Short Pulses Laser (UPL) for industrial applications passes through the use of both fast beam scanning systems and high repetition rate, high average power P, UPL. Nevertheless unwanted thermal effects are expected when P exceeds some tens of W. An interesting strategy for a reliable heat management would consists in texturing with a low fluence values (slightly higher than the ablation threshold) and utilising a Polygon Scanner Heads delivering laser pulses with unrepeated speed. Here we show for the first time that with relatively low fluence it is possible over stainless steel, to obtain surface texturing by utilising a 2 MHz femtosecond laser jointly with a polygonal scanner head in a relatively low fluence regime (0.11 J cm{sup −2}). Different surface textures (Ripples, micro grooves and spikes) can be obtained varying the scan speed from 90 m s{sup −1} to 25 m s{sup −1}. In particular, spikes formation process has been shown and optimised at 25 m s{sup −1} and a full morphology characterization by SEM has been carried out. Reflectance measurements with integrating sphere are presented to compare reference surface with high scan rate textures. In the best case we show a black surface with reflectance value < 5%.

Speed control of switched reluctance motor using sliding mode control strategy

Energy Technology Data Exchange (ETDEWEB)

John, G. [Kenetech Windpower, Livermore, CA (United States); Eastham, A.R. [Queen`s Univ., Kingston, Ontario (Canada). Dept. of Electrical Engineering

1995-12-31

A robust speed drive system for a switched reluctance motor (SRM) using sliding mode control strategy (SLMC) is presented. After reviewing the operation of an SRM drive, a SLMC based scheme is formulated to control the drive speed. The scheme is implemented using a micro-controller and a high resolution position sensor. The parameter insensitive characteristics are demonstrated through computer simulations and experimental verification.

Design and control of the precise tracking bed based on complex electromechanical design theory

Science.gov (United States)

Ren, Changzhi; Liu, Zhao; Wu, Liao; Chen, Ken

2010-05-01

The precise tracking technology is wide used in astronomical instruments, satellite tracking and aeronautic test bed. However, the precise ultra low speed tracking drive system is one high integrated electromechanical system, which one complexly electromechanical design method is adopted to improve the efficiency, reliability and quality of the system during the design and manufacture circle. The precise Tracking Bed is one ultra-exact, ultra-low speed, high precision and huge inertial instrument, which some kind of mechanism and environment of the ultra low speed is different from general technology. This paper explores the design process based on complex electromechanical optimizing design theory, one non-PID with a CMAC forward feedback control method is used in the servo system of the precise tracking bed and some simulation results are discussed.

Reverse bistable effect in ferroelectric liquid crystal devices with ultra-fast switching at low driving voltage.

Science.gov (United States)

Guo, Qi; Zhao, Xiaojin; Zhao, Huijie; Chigrinov, V G

2015-05-15

In this Letter, reverse bistable effect with deep-sub-millisecond switching time is first reported in ferroelectric liquid crystal (FLC) devices using a homogeneous photo-alignment technique. It is indicated by our experimental results that both the anchoring energy and the dielectric property of the FLC's alignment layer is critical for the existence of the reverse bistable effect. In addition, with the derived criteria of the reverse bistable effect, we quantitatively analyze the switching dynamics of the reverse bistable FLC and the transition condition between the traditional bistability and our presented reverse bistability. Moreover, the fabricated FLC device exhibits an ultra-fast switching of ∼160  μs and a high contrast ratio of 1000:1, both of which were measured at a low driving voltage of 11 V. The featured deep-sub-millisecond switching time is really advantageous for our presented reverse bistable FLC devices, which enables a significant quality improvement of the existing optical devices, as well as a wide range of new applications in photonics and display areas.

Super Boiler: First Generation, Ultra-High Efficiency Firetube Boiler

Energy Technology Data Exchange (ETDEWEB)

None

2006-06-01

This factsheet describes a research project whose goal is to develop and demonstrate a first-generation ultra-high-efficiency, ultra-low emissions, compact gas-fired package boiler (Super Boiler), and formulate a long-range RD&D plan for advanced boiler technology out to the year 2020.

Speed control for a two-mass drive system using integrated fuzzy estimator and hybrid fuzzy PD/PI controller

International Nuclear Information System (INIS)

Pai, N-S; Kuo, Y-P

2008-01-01

This paper presents a novel speed control scheme for a 2- mass motor drive system. The speed controller is based on the estimated state feedback compensation. The integrated fuzzy observer can give a fast and accuracy estimation of the unmeasured states. Two kinds of hybrid fuzzy proportional-derivative and proportional-integral (HF PD/PI) are proposed to cope with this speed control problem. The first is the static HF PD/PI controller and the second is the dynamic one. Simulation results show that the developed integrated fuzzy observer provide the better estimation performance than that of the Kalman filter and the proposed control schemes can effectively track the desired speed in the presence of load disturbance

High-speed AC motors

Energy Technology Data Exchange (ETDEWEB)

Jokinen, T.; Arkkio, A. [Helsinki University of Technology Laboratory of Electromechanics, Otaniemi (Finland)

1997-12-31

The paper deals with various types of highspeed electric motors, and their limiting powers. Standard machines with laminated rotors can be utilised if the speed is moderate. The solid rotor construction makes it possible to reach higher power and speed levels than those of laminated rotors. The development work on high-speed motors done at Helsinki University of Technology is presented, too. (orig.) 12 refs.

Transistorized PWM inverter-induction motor drive system

Science.gov (United States)

Peak, S. C.; Plunkett, A. B.

1982-01-01

This paper describes the development of a transistorized PWM inverter-induction motor traction drive system. A vehicle performance analysis was performed to establish the vehicle tractive effort-speed requirements. These requirements were then converted into a set of inverter and motor specifications. The inverter was a transistorized three-phase bridge using General Electric power Darlington transistors. The description of the design and development of this inverter is the principal object of this paper. The high-speed induction motor is a design which is optimized for use with an inverter power source. The primary feedback control is a torque angle control with voltage and torque outer loop controls. A current-controlled PWM technique is used to control the motor voltage. The drive has a constant torque output with PWM operation to base motor speed and a constant horsepower output with square wave operation to maximum speed. The drive system was dynamometer tested and the results are presented.

Synthesis of realistic driving cycles with high accuracy and computational speed, including slope information

NARCIS (Netherlands)

Silvas, E.; Hereijgers, K.; Peng, Huei; Hofman, T.; Steinbuch, M.

2016-01-01

This paper describes a new method to synthesize driving cycles, where not only the velocity is considered, yet also the road slope information of the real-world measured driving cycle. Driven by strict emission regulations and tight fuel targets, hybrid or electric vehicle manufacturers aim to

Evaluation of an Advanced Harmonic Filter for Adjustable Speed Drives using a Toolbox Approach

DEFF Research Database (Denmark)

Asiminoaei, Lucian; Hansen, Steffan; Blaabjerg, Frede

2004-01-01

A large diversity of solutions exists to reduce the harmonic emission of the 6-pulse Adjustable Speed Drive in order to fulfill the requirements of the international harmonic standards. Among them, new types of advanced harmonic filters recently gained an increased attention due to their good...... a combination of a pre-stored database and new interpolation techniques the toolbox can provide the harmonic data on real applications allowing comparisons between different mitigation solutions....

Ultra high resolution tomography

Energy Technology Data Exchange (ETDEWEB)

Haddad, W.S.

1994-11-15

Recent work and results on ultra high resolution three dimensional imaging with soft x-rays will be presented. This work is aimed at determining microscopic three dimensional structure of biological and material specimens. Three dimensional reconstructed images of a microscopic test object will be presented; the reconstruction has a resolution on the order of 1000 A in all three dimensions. Preliminary work with biological samples will also be shown, and the experimental and numerical methods used will be discussed.

75 FR 81284 - Nationwide Use of High Frequency and Ultra High Frequency Active SONAR Technology; Draft...

Science.gov (United States)

2010-12-27

... Frequency and Ultra High Frequency Active SONAR Technology; Draft Programmatic Environmental Assessment and... Programmatic Environmental Assessment (PEA) for the Nationwide Use of High Frequency (HF) and Ultra High... potential impacts of each alternative on the human and natural environments. DATES: Comments and related...

Effects of DC-link Filter on Harmonic and Interharmonic Generation in Three-phase Adjustable Speed Drive Systems

DEFF Research Database (Denmark)

Soltani, Hamid; Davari, Pooya; Kumar, Dinesh

2017-01-01

Harmonic and interharmonic distortions are considered as the main power quality issues especially in the distribution networks. The double-stage Adjustable Speed Drives (ASDs) in which the front-end diode rectifier is connected to a rear-end inverter through an intermediate DC-link filter may inj...

High-Speed Interferometry Under Impacting Drops

KAUST Repository

Langley, Kenneth R.; Li, Erqiang; Thoroddsen, Sigurdur T

2017-01-01

Over the last decade the rapid advances in high-speed video technology, have opened up to study many multi-phase fluid phenomena, which tend to occur most rapidly on the smallest length-scales. One of these is the entrapment of a small bubble under a drop impacting onto a solid surface. Here we have gone from simply observing the presence of the bubble to detailed imaging of the formation of a lubricating air-disc under the drop center and its subsequent contraction into the bubble. Imaging the full shape-evolution of the air-disc has required μm and sub-μs space and time resolutions. Time-resolved 200 ns interferometry with monochromatic light, has allowed us to follow individual fringes to obtain absolute air-layer thicknesses, based on the eventual contact with the solid. We can follow the evolution of the dimple shape as well as the compression of the gas. The improved imaging has also revealed new levels of detail, like the nature of the first contact which produces a ring of micro-bubbles, highlighting the influence of nanometric surface roughness. Finally, for impacts of ultra-viscous drops we see gliding on ~100 nm thick rarified gas layers, followed by extreme wetting at numerous random spots.

High-Speed Interferometry Under Impacting Drops

KAUST Repository

Langley, Kenneth R.

2017-08-31

Over the last decade the rapid advances in high-speed video technology, have opened up to study many multi-phase fluid phenomena, which tend to occur most rapidly on the smallest length-scales. One of these is the entrapment of a small bubble under a drop impacting onto a solid surface. Here we have gone from simply observing the presence of the bubble to detailed imaging of the formation of a lubricating air-disc under the drop center and its subsequent contraction into the bubble. Imaging the full shape-evolution of the air-disc has required μm and sub-μs space and time resolutions. Time-resolved 200 ns interferometry with monochromatic light, has allowed us to follow individual fringes to obtain absolute air-layer thicknesses, based on the eventual contact with the solid. We can follow the evolution of the dimple shape as well as the compression of the gas. The improved imaging has also revealed new levels of detail, like the nature of the first contact which produces a ring of micro-bubbles, highlighting the influence of nanometric surface roughness. Finally, for impacts of ultra-viscous drops we see gliding on ~100 nm thick rarified gas layers, followed by extreme wetting at numerous random spots.

Chromatically encoded high-speed photography of cavitation bubble dynamics inside inhomogeneous ophthalmic tissue

Science.gov (United States)

Tinne, N.; Matthias, B.; Kranert, F.; Wetzel, C.; Krüger, A.; Ripken, T.

2016-03-01

The interaction effect of photodisruption, which is used for dissection of biological tissue with fs-laser pulses, has been intensively studied inside water as prevalent sample medium. In this case, the single effect is highly reproducible and, hence, the method of time-resolved photography is sufficiently applicable. In contrast, the reproducibility significantly decreases analyzing more solid and anisotropic media like biological tissue. Therefore, a high-speed photographic approach is necessary in this case. The presented study introduces a novel technique for high-speed photography based on the principle of chromatic encoding. For illumination of the region of interest within the sample medium, the light paths of up to 12 LEDs with various emission wavelengths are overlaid via optical filters. Here, MOSFET-electronics provide a LED flash with a duration diodes are externally triggered with a distinct delay for every LED. Furthermore, the different illumination wavelengths are chromatically separated again for detection via camera chip. Thus, the experimental setup enables the generation of a time-sequence of laser-tissue interaction inside anisotropic biological tissue and for the optimization of the surgical process with high-repetition rate fs-lasers. Additionally, this application is also suitable for the investigation of other microscopic, ultra-fast events in transparent inhomogeneous materials.

High-power converters and AC drives

CERN Document Server

Wu, Bin

2017-01-01

This new edition reflects the recent technological advancements in the MV drive industry, such as advanced multilevel converters and drive configurations. It includes three new chapters, Control of Synchronous Motor Drives, Transformerless MV Drives, and Matrix Converter Fed Drives. In addition, there are extensively revised chapters on Multilevel Voltage Source Inverters and Voltage Source Inverter-Fed Drives. This book includes a systematic analysis on a variety of high-power multilevel converters, illustrates important concepts with simulations and experiments, introduces various megawatt drives produced by world leading drive manufacturers, and addresses practical problems and their mitigations methods.

Shock characterization of an ultra-high strength concrete

International Nuclear Information System (INIS)

Erzar, B.; Pontiroli, C.; Buzaud, E.

2016-01-01

Nowadays, the design of protective structures may imply ultra-high performance concretes. These materials present a compressive strength 5 times higher than standard concretes. However, few reliable data on the shock response of such materials are available in the literature. Thus, a characterization of an ultra-high strength concrete has been conducted by means of hydrostatic and triaxial tests in the quasi-static regime, and plate impact experiments for shock response. Data have been gathered up to 6 GPa and a simple modelling approach has been applied to get a reliable representation of the shock compression of this concrete. (authors)

32 CFR 636.22 - Speed regulations.

Science.gov (United States)

2010-07-01

...). (d) The following special speed limits apply: (1) When passing troop formations, 10 miles per hour... vehicles and will obey the following off-road driving speeds: Day Driving: Trails, 16 MPH Cross County, 6 MPH Night Driving: Trails, 5 MPH (with headlights) Cross Country, 5 MPH Night Driving: Trails, 4 MPH...

State all-driver distracted driving laws and high school students'  texting while driving behavior.

Science.gov (United States)

Qiao, Nan; Bell, Teresa Maria

2016-01-01

Texting while driving is highly prevalent among adolescents and young adults in the United States. Texting while driving can significantly increase the risk of road crashes and is associated with other risky driving behaviors. Most states have enacted distracted driving laws to prohibit texting while driving. This study examines effects of different all-driver distracted driving laws on texting while driving among high school students. High school student data were extracted from the 2013 National Youth Risk Behavior Survey. Distracted driving law information was collected from the National Conference of State Legislatures. The final sample included 6,168 high school students above the restricted driving age in their states and with access to a vehicle. Logistic regression was applied to estimate odds ratios of laws on texting while driving. All-driver text messaging bans with primary enforcement were associated with a significant reduction in odds of texting while driving among high school students (odds ratio = 0.703; 95% confidence interval, 0.513-0.964), whereas all-driver phone use bans with primary enforcement did not have a significant association with texting while driving (odds ratio = 0.846; 95% confidence interval, 0.501-1.429). The findings indicate that all-driver distracted driving laws that specifically target texting while driving as opposed to all types of phone use are effective in reducing the behavior among high school students.

Ultra-high vacuum compatible optical chopper system for synchrotron x-ray scanning tunneling microscopy

Energy Technology Data Exchange (ETDEWEB)

Chang, Hao, E-mail: hc000211@ohio.edu [Advanced Photon Source, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); Nanoscale and Quantum Phenomena Institute, Physics & Astronomy Department, Ohio University, Athens, Ohio 45701 (United States); Cummings, Marvin; Shirato, Nozomi; Stripe, Benjamin; Preissner, Curt; Freeland, John W. [Advanced Photon Source, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); Rosenmann, Daniel [Center for Nanoscale Materials, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); Kersell, Heath; Hla, Saw-Wai [Nanoscale and Quantum Phenomena Institute, Physics & Astronomy Department, Ohio University, Athens, Ohio 45701 (United States); Center for Nanoscale Materials, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); Rose, Volker, E-mail: vrose@anl.gov [Advanced Photon Source, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); Center for Nanoscale Materials, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439 (United States)

2016-01-28

High-speed beam choppers are a crucial part of time-resolved x-ray studies as well as a necessary component to enable elemental contrast in synchrotron x-ray scanning tunneling microscopy (SX-STM). However, many chopper systems are not capable of operation in vacuum, which restricts their application to x-ray studies with high photon energies, where air absorption does not present a significant problem. To overcome this limitation, we present a fully ultra-high vacuum (UHV) compatible chopper system capable of operating at variable chopping frequencies up to 4 kHz. The lightweight aluminum chopper disk is coated with Ti and Au films to provide the required beam attenuation for soft and hard x-rays with photon energies up to about 12 keV. The chopper is used for lock-in detection of x-ray enhanced signals in SX-STM.

Sintering of ultra high molecular weight polyethylene

Indian Academy of Sciences (India)

Abstract. Ultra high molecular weight polyethylene (UHMWPE) is a high performance polymer having low coefficient of friction, good abrasion resistance, good chemical ... In this study, we report our results on compaction and sintering behaviour of two grades of UHMWPE with reference to the powder morphology, sintering ...

Pay as You Speed, ISA with incentives for not speeding

DEFF Research Database (Denmark)

Lahrmann, Harry Spaabæk; Agerholm, Niels; Tradisauskas, Nerius

2012-01-01

The Intelligent Speed Adaptation (ISA) project we describe in this article is based on Pay as You Drive principles. These principles assume that the ISA equipment informs a driver of the speed limit, warns the driver when speeding and calculates penalty points. Each penalty point entails the redu......The Intelligent Speed Adaptation (ISA) project we describe in this article is based on Pay as You Drive principles. These principles assume that the ISA equipment informs a driver of the speed limit, warns the driver when speeding and calculates penalty points. Each penalty point entails...... the reduction of a 30% discount on the driver's car insurance premium, which therefore produced the name, Pay as You Speed. The ISA equipment consists of a GPS-based On Board Unit with a mobile phone connection to a web server. The project was planned for a three-year test period with 300 young car drivers...

Mechanism and experimental research on ultra-precision grinding of ferrite

Science.gov (United States)

Ban, Xinxing; Zhao, Huiying; Dong, Longchao; Zhu, Xueliang; Zhang, Chupeng; Gu, Yawen

2017-02-01

Ultra-precision grinding of ferrite is conducted to investigate the removal mechanism. Effect of the accuracy of machine tool key components on grinding surface quality is analyzed. The surface generation model of ferrite ultra-precision grinding machining is established. In order to reveal the surface formation mechanism of ferrite in the process of ultraprecision grinding, furthermore, the scientific and accurate of the calculation model are taken into account to verify the grinding surface roughness, which is proposed. Orthogonal experiment is designed using the high precision aerostatic turntable and aerostatic spindle for ferrite which is a typical hard brittle materials. Based on the experimental results, the influence factors and laws of ultra-precision grinding surface of ferrite are discussed through the analysis of the surface roughness. The results show that the quality of ferrite grinding surface is the optimal parameters, when the wheel speed of 20000r/mm, feed rate of 10mm/min, grinding depth of 0.005mm, and turntable rotary speed of 5r/min, the surface roughness Ra can up to 75nm.

Chinese carless young drivers' self-reported driving behavior and simulated driving performance.

Science.gov (United States)

Zhang, Qian; Jiang, Zuhua; Zheng, Dongpeng; Man, Dong; Xu, Xunnan

2013-01-01

Carless young drivers refers to those drivers aged between 18 and 25 years who have a driver's license but seldom have opportunities to practice their driving skills because they do not have their own cars. Due to China's lower private car ownership, many young drivers become carless young drivers after licensure, and the safety issue associated with them has raised great concern in China. This study aims to provide initial insight into the self-reported driving behaviors and simulated driving performance of Chinese carless young drivers. Thirty-three carless young drivers and 32 young drivers with their own cars (as a comparison group) participated in this study. A modified Driver Behavior Questionnaire (DBQ) with a 4-factor structure (errors, violations, attention lapses, and memory lapses) was used to study carless young drivers' self-reported driving behaviors. A simulated driving experiment using a low-cost, fixed-base driving simulator was conducted to measure their simulated driving performance (errors, violations, attention lapses, driving maintenance, reaction time, and accidents). Self-reported DBQ outcomes showed that carless young drivers reported similar errors, more attention lapses, fewer memory lapses, and significantly fewer violation behaviors relative to young drivers with their own cars, whereas simulated driving results revealed that they committed significantly more errors, attention lapses, and violation behaviors than the comparison group. Carless young drivers had a lower ability to maintain the stability of speed and lane position, drove more cautiously approaching and passing through red traffic lights, and committed more accidents during simulated driving. A tendency to speed was not found among carless young drivers; their average speed and speeding frequency were all much lower than that of the comparison group. Lifetime mileage was the only significant predictor of carless young drivers' self-reported violations, simulated violations

Adaptive Optics System with Deformable Composite Mirror and High Speed, Ultra-Compact Electronics

Science.gov (United States)

Chen, Peter C.; Knowles, G. J.; Shea, B. G.

2006-06-01

We report development of a novel adaptive optics system for optical astronomy. Key components are very thin Deformable Mirrors (DM) made of fiber reinforced polymer resins, subminiature PMN-PT actuators, and low power, high bandwidth electronics drive system with compact packaging and minimal wiring. By using specific formulations of fibers, resins, and laminate construction, we are able to fabricate mirror face sheets that are thin (2 KHz. By utilizing QorTek’s proprietary synthetic impendence power supply technology, all the power, control, and signal extraction for many hundreds to 1000s of actuators and sensors can be implemented on a single matrix controller printed circuit board co-mounted with the DM. The matrix controller, in turn requires only a single serial bus interface, thereby obviating the need for massive wiring harnesses. The technology can be scaled up to multi-meter aperture DMs with >100K actuators.

Distributed and self-adaptive vehicle speed estimation in the composite braking case for four-wheel drive hybrid electric car

Science.gov (United States)

Zhao, Z.-G.; Zhou, L.-J.; Zhang, J.-T.; Zhu, Q.; Hedrick, J.-K.

2017-05-01

Considering the controllability and observability of the braking torques of the hub motor, Integrated Starter Generator (ISG), and hydraulic brake for four-wheel drive (4WD) hybrid electric cars, a distributed and self-adaptive vehicle speed estimation algorithm for different braking situations has been proposed by fully utilising the Electronic Stability Program (ESP) sensor signals and multiple powersource signals. Firstly, the simulation platform of a 4WD hybrid electric car was established, which integrates an electronic-hydraulic composited braking system model and its control strategy, a nonlinear seven degrees-of-freedom vehicle dynamics model, and the Burckhardt tyre model. Secondly, combining the braking torque signals with the ESP signals, self-adaptive unscented Kalman sub-filter and main-filter adaptable to the observation noise were, respectively, designed. Thirdly, the fusion rules for the sub-filters and master filter were proposed herein, and the estimation results were compared with the simulated value of a real vehicle speed. Finally, based on the hardware in-the-loop platform and by picking up the regenerative motor torque signals and wheel cylinder pressure signals, the proposed speed estimation algorithm was tested under the case of moderate braking on the highly adhesive road, and the case of Antilock Braking System (ABS) action on the slippery road, as well as the case of ABS action on the icy road. Test results show that the presented vehicle speed estimation algorithm has not only a high precision but also a strong adaptability in the composite braking case.

Electric drive motors for industrial robots

Science.gov (United States)

Fichtner, K.

1985-04-01

In robotized industrial plants it is possible to use electric motors in the technological process and also for control, assembly, transport, testing, and measurements. Particularly suitable for these applications are permanent-magnet d.c. motors. A new special series was developed for industrial robots with hinge joints in kinematic pairs. The complete drive includes thyristors or transistor controls with regulators and, if necessary, a line transformer as well as a servomotor with tachometer and odometer for speed, current, and position control. The drive is coupled to a robot tong through mechanical torque and force converters. In addition to a 0 to 4000 rpm speed regulation, without wobble at low speeds, and a high torque-to-weight ratio for repetitive short-time heavy duty, these low-inertia motors develop high starting and accelerating torques over the entire speed range. They operate from a 1 to O 220 V a.c. line through a rectifier. The motors are totally enclosed, or of open construction for better ventilation. Their windings have class F insulation for operation at ambient temperatures up to 40 C.

Ultra-low noise supercontinuum source for ultra-high resolution optical coherence tomography at 1300 nm

Science.gov (United States)

Gonzalo, I. B.; Maria, M.; Engelsholm, R. D.; Feuchter, T.; Leick, L.; Moselund, P. M.; Podoleanu, A.; Bang, O.

2018-02-01

Supercontinuum (SC) sources are of great interest for many applications due to their ultra-broad optical bandwidth, good beam quality and high power spectral density [1]. In particular, the high average power over large bandwidths makes SC light sources excellent candidates for ultra-high resolution optical coherence tomography (UHR-OCT) [2-5]. However, conventional SC sources suffer from high pulse-to-pulse intensity fluctuations as a result of the noise-sensitive nonlinear effects involved in the SC generation process [6-9]. This intensity noise from the SC source can limit the performance of OCT, resulting in a reduced signal-to-noise ratio (SNR) [10-12]. Much work has been done to reduce the noise of the SC sources for instance with fiber tapers [7,8] or increasing the repetition rate of the pump laser for averaging in the spectrometer [10,12]. An alternative approach is to use all-normal dispersion (ANDi) fibers [13,14] to generate SC light from well-known coherent nonlinear processes [15-17]. In fact, reduction of SC noise using ANDi fibers compared to anomalous dispersion SC pumped by sub-picosecond pulses has been recently demonstrated [18], but a cladding mode was used to stabilize the ANDi SC. In this work, we characterize the noise performance of a femtosecond pumped ANDi based SC and a commercial SC source in an UHR-OCT system at 1300 nm. We show that the ANDi based SC presents exceptional noise properties compared to a commercial source. An improvement of 5 dB in SNR is measured in the UHR-OCT system, and the noise behavior resembles that of a superluminiscent diode. This preliminary study is a step forward towards development of an ultra-low noise SC source at 1300 nm for ultra-high resolution OCT.

Overview of Variable-Speed Power-Turbine Research

Science.gov (United States)

Welch, Gerard E.

2011-01-01

The vertical take-off and landing (VTOL) and high-speed cruise capability of the NASA Large Civil Tilt-Rotor (LCTR) notional vehicle is envisaged to enable increased throughput in the national airspace. A key challenge of the LCTR is the requirement to vary the main rotor speeds from 100% at take-off to near 50% at cruise as required to minimize mission fuel burn. The variable-speed power-turbine (VSPT), driving a fixed gear-ratio transmission, provides one approach for effecting this wide speed variation. The key aerodynamic and rotordynamic challenges of the VSPT were described in the FAP Conference presentation. The challenges include maintaining high turbine efficiency at high work factor, wide (60 deg.) of incidence variation in all blade rows due to the speed variation, and operation at low Reynolds numbers (with transitional flow). The PT -shaft of the VSPT must be designed for safe operation in the wide speed range required, and therefore poses challenges associated with rotordynamics. The technical challenges drive research activities underway at NASA. An overview of the NASA SRW VSPT research activities was provided. These activities included conceptual and preliminary aero and mechanical (rotordynamics) design of the VSPT for the LCTR application, experimental and computational research supporting the development of incidence tolerant blading, and steps toward component-level testing of a variable-speed power-turbine of relevance to the LCTR application.

High speed heterostructure devices

CERN Document Server

Beer, Albert C; Willardson, R K; Kiehl, Richard A; Sollner, T C L Gerhard

1994-01-01

Volume 41 includes an in-depth review of the most important, high-speed switches made with heterojunction technology. This volume is aimed at the graduate student or working researcher who needs a broad overview andan introduction to current literature. Key Features * The first complete review of InP-based HFETs and complementary HFETs, which promise very low power and high speed * Offers a complete, three-chapter review of resonant tunneling * Provides an emphasis on circuits as well as devices.

Further demonstration of the VRLA-type UltraBattery under medium-HEV duty and development of the flooded-type UltraBattery for micro-HEV applications

Energy Technology Data Exchange (ETDEWEB)

Furukawa, J.; Takada, T.; Monma, D. [The Furukawa Battery Co., Ltd., R and D Division, 23-6 Kuidesaku, Shimofunao-machi, Joban, Iwaki-city, 972-8501 (Japan); Lam, L.T. [CSIRO Energy Technology, Bayview Avenue, Clayton South, Vic. 3169 (Australia)

2010-02-15

The UltraBattery has been invented by the CSIRO Energy Technology in Australia and has been developed and produced by the Furukawa Battery Co., Ltd., Japan. This battery is a hybrid energy storage device which combines a super capacitor and a lead-acid battery in single unit cells, taking the best from both technologies without the need of extra, expensive electronic controls. The capacitor enhances the power and lifespan of the lead-acid battery as it acts as a buffer during high-rate discharging and charging, thus enabling it to provide and absorb charge rapidly during vehicle acceleration and braking. The laboratory results of the prototype valve-regulated UltraBatteries show that the capacity, power, available energy, cold cranking and self-discharge of these batteries have met, or exceeded, all the respective performance targets set for both minimum and maximum power-assist HEVs. The cycling performance of the UltraBatteries under micro-, mild- and full-HEV duties is at least four times longer than that of the state-of-the-art lead-acid batteries. Importantly, the cycling performance of UltraBatteries is proven to be comparable or even better than that of the Ni-MH cells. On the other hand, the field trial of UltraBatteries in the Honda Insight HEV shows that the vehicle has surpassed 170,000 km and the batteries are still in a healthy condition. Furthermore, the UltraBatteries demonstrate very good acceptance of the charge from regenerative braking even at high state-of-charge, e.g., 70% during driving. Therefore, no equalization charge is required for the UltraBatteries during field trial. The HEV powered by UltraBatteries gives slightly higher fuel consumption (cf., 4.16 with 4.05 L/100 km) and CO{sub 2} emissions (cf., 98.8 with 96 g km{sup -1}) compared with that by Ni-MH cells. There are no differences in driving experience between the Honda Insight powered by UltraBatteries and by Ni-MH cells. Given such comparable performance, the UltraBattery pack

Monitoring speed before and during a speed publicity campaign.

NARCIS (Netherlands)

Schagen, I.N.L.G. van Commandeur, J.J.F. Goldenbeld, C. & Stipdonk, H.

2016-01-01

Driving speeds were monitored during a period of 16 weeks encompassing different stages of an anti-speeding campaign in the Netherlands. This campaign targeted speed limit violations in built-up areas. The observation periods differed in terms of intensity and media used for the campaign. Small

An innovative ultra-capacitor driven shape memory alloy actuator with an embedded control system

International Nuclear Information System (INIS)

Li, Peng; Song, Gangbing

2014-01-01

In this paper, an innovative ultra-capacitor driven shape memory alloy (SMA) actuator with an embedded control system is proposed targeting high power high-duty cycle SMA applications. The ultra-capacitor, which is capable of delivering massive amounts of instantaneous current in a compact dimension for high power applications, is chosen as the main component of the power supply. A specialized embedded system is designed from the ground up to control the ultra-capacitor driven SMA system. The control of the ultra-capacitor driven SMA is different from that of a regular constant voltage powered SMA system in that the energy and the voltage of the ultra-capacitor decrease as the system load increases. The embedded control system is also different from a computer-based control system in that it has limited computational power, and the control algorithm has to be designed to be simple while effective so that it can fit into the embedded system environment. The problem of a variable voltage power source induced by the use of the ultra-capacitor is solved by using a fuzzy PID (proportional integral and derivative) control. The method of using an ultra-capacitor to drive SMA actuators enabled SMA as a good candidate for high power high-duty cycle applications. The proposed embedded control system provides a good and ready-to-use solution for SMA high power applications. (paper)

A novel dual motor drive system for three wheel electric vehicles

Science.gov (United States)

Panmuang, Piyapat; Thongsan, Taweesak; Suwapaet, Nuchida; Laohavanich, Juckamass; Photong, Chonlatee

2018-03-01

This paper presents a novel dual motor drive system used for three wheel electric vehicles that have one free wheel at the front and two wheels with a drive system at the end of the vehicles. A novel dual motor drive system consists of two identical DC motors that are independently controlled by its speed-torque controller. Under light load conditions, only one of the DC motors will operate around it rated whilst under hard load conditions both of the DC motors will operate. With this drive system, the motors will operate only at its high performance at rated or else no operate to retain longer lifetime. The simulated results for the Skylab three wheel electric vehicle prototype with 8kW at full load (high torque, low speed) and around 4kW at light/normal operating loads (regular speed-torque) showed that the proposed system provides better dynamic responses with faster overshoot current/voltage recovery time, has lower investment costs, has longer lifetime of the motors and allows the motors to always operate at their high performance and thus achieve more cost effective system compared to a single motor drive system with 8kW DC motors.

A sampling ultra-high-speed streak camera based on the use of a unique photomultiplier

International Nuclear Information System (INIS)

Marode, Emmanuel

An apparatus reproducing the ''streak'' mode of a high-speed camera is proposed for the case of a slit AB whose variations in luminosity are repetitive. A photomultiplier, analysing the object AB point by point, and a still camera, photographing a slit fixed on the oscilloscope screen parallel to the sweep direction are placed on a mobile platform P. The movement of P assures a time-resolved analysis of AB. The resolution is of the order of 2.10 -9 s, and can be improved [fr

Driving context influences drivers' decision to engage in visual-manual phone tasks: Evidence from a naturalistic driving study.

Science.gov (United States)

Tivesten, Emma; Dozza, Marco

2015-06-01

Visual-manual (VM) phone tasks (i.e., texting, dialing, reading) are associated with an increased crash/near-crash risk. This study investigated how the driving context influences drivers' decisions to engage in VM phone tasks in naturalistic driving. Video-recordings of 1,432 car trips were viewed to identify VM phone tasks and passenger presence. Video, vehicle signals, and map data were used to classify driving context (i.e., curvature, other vehicles) before and during the VM phone tasks (N=374). Vehicle signals (i.e., speed, yaw rate, forward radar) were available for all driving. VM phone tasks were more likely to be initiated while standing still, and less likely while driving at high speeds, or when a passenger was present. Lead vehicle presence did not influence how likely it was that a VM phone task was initiated, but the drivers adjusted their task timing to situations when the lead vehicle was increasing speed, resulting in increasing time headway. The drivers adjusted task timing until after making sharp turns and lane change maneuvers. In contrast to previous driving simulator studies, there was no evidence of drivers reducing speed as a consequence of VM phone task engagement. The results show that experienced drivers use information about current and upcoming driving context to decide when to engage in VM phone tasks. However, drivers may fail to sufficiently increase safety margins to allow time to respond to possible unpredictable events (e.g., lead vehicle braking). Advanced driver assistance systems should facilitate and possibly boost drivers' self-regulating behavior. For instance, they might recognize when appropriate adaptive behavior is missing and advise or alert accordingly. The results from this study could also inspire training programs for novice drivers, or locally classify roads in terms of the risk associated with secondary task engagement while driving. Copyright © 2015. Published by Elsevier Ltd.

Practical Wide-speed-range Sensorless Control System for Permanent Magnet Reluctance Synchronous Motor Drives via Active Flux Model

DEFF Research Database (Denmark)

Ancuti, Mihaela Codruta; Tutelea, Lucian; Andreescu, Gheorghe-Daniel

2014-01-01

This article introduces a control strategy to obtain near-maximum available torque in a wide speed range with sensorless operation via the active flux concept for permanent magnet-reluctance synchronous motor drives. A new torque dq current reference calculator is proposed, with reference torque...

The Attentional Demand of Automobile Driving Revisited: Occlusion Distance as a Function of Task-Relevant Event Density in Realistic Driving Scenarios.

Science.gov (United States)

Kujala, Tuomo; Mäkelä, Jakke; Kotilainen, Ilkka; Tokkonen, Timo

2016-02-01

We studied the utility of occlusion distance as a function of task-relevant event density in realistic traffic scenarios with self-controlled speed. The visual occlusion technique is an established method for assessing visual demands of driving. However, occlusion time is not a highly informative measure of environmental task-relevant event density in self-paced driving scenarios because it partials out the effects of changes in driving speed. Self-determined occlusion times and distances of 97 drivers with varying backgrounds were analyzed in driving scenarios simulating real Finnish suburban and highway traffic environments with self-determined vehicle speed. Occlusion distances varied systematically with the expected environmental demands of the manipulated driving scenarios whereas the distributions of occlusion times remained more static across the scenarios. Systematic individual differences in the preferred occlusion distances were observed. More experienced drivers achieved better lane-keeping accuracy than inexperienced drivers with similar occlusion distances; however, driving experience was unexpectedly not a major factor for the preferred occlusion distances. Occlusion distance seems to be an informative measure for assessing task-relevant event density in realistic traffic scenarios with self-controlled speed. Occlusion time measures the visual demand of driving as the task-relevant event rate in time intervals, whereas occlusion distance measures the experienced task-relevant event density in distance intervals. The findings can be utilized in context-aware distraction mitigation systems, human-automated vehicle interaction, road speed prediction and design, as well as in the testing of visual in-vehicle tasks for inappropriate in-vehicle glancing behaviors in any dynamic traffic scenario for which appropriate individual occlusion distances can be defined. © 2015, Human Factors and Ergonomics Society.

Fiscal 1998 R and D report on femtosecond technology (ultra-short pulse optoelectronics technology); 1998 nendo femuto byo technology no kenkyu kaihatsu (chotan pulse hikari electronics gijutsu kaihatsu) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report reports the result of the fiscal 1998 R and D on femtosecond technology supported by NEDO. For creation of industrial basic technologies supporting the advanced information society in the 21st century, ultra-high speed electronics technology including new functions beyond the speed limit of conventional electronics technologies is indispensable. From such viewpoint, this R and D aims at establishment of the basic technology necessary for ultra- high speed electronics technology through R and D of technology controlling conditions of beams and electrons in a femtosecond (10{sup -15}-10{sup -12} seconds) region. In fiscal 1998, this project first succeeded in fabrication of a prototype pulse compressor by using semiconductors, and developed a new pulse compressing method by using fibers to generate ultra-short pulse of 38fs. By developing new materials for intersubband transition where ultra-high speed responses can be expected, optical absorption by intersubband transition was first confirmed at optical communication wavelength. The main result for every theme is reported and explained. (NEDO)

Ultra-high Efficiency DC-DC Converter using GaN Devices

DEFF Research Database (Denmark)

Ramachandran, Rakesh

2016-01-01

properties of GaN devices can be utilized in power converters to make them more compact and highly efficient. This thesis entitled “Ultra-high Efficiency DC-DC Converter using GaN devices” focuses on achieving ultra-high conversion efficiency in an isolated dc-dc converter by the optimal utilization of Ga...... for many decades. However, the rate of improvement slowed as the silicon power materials asymptotically approached its theoretical bounds. Compared to Si, wideband gap materials such as Silicon Carbide (SiC) and Gallium Nitride (GaN) are promising semiconductors for power devices due to their superior...... in this thesis. Efficiency measurements from the hardware prototype of both the topologies are also presented in this thesis. Finally, the bidirectional operation of an optimized isolated dc-dc converter is presented. The optimized converter has achieved an ultra-high efficiency of 98.8% in both directions...

Ultra-high energy cosmic rays and prompt TeV gamma rays from ...

Indian Academy of Sciences (India)

physics pp. 789-792. Ultra-high energy cosmic rays and prompt. TeV gamma rays from gamma ray bursts ... The origin of the observed ultra-high energy cosmic ray (UHECR) events with ... are proton and electron rest mass, respectively.

Scaling violations at ultra-high energies

International Nuclear Information System (INIS)

Tung, W.K.

1979-01-01

The paper discusses some of the features of high energy lepton-hadron scattering, including the observed (Bjorken) scaling behavior. The cross-sections where all hadron final states are summed over, are examined and the general formulas for the differential cross-section are examined. The subjects of scaling, breaking and phenomenological consequences are studied, and a list of what ultra-high energy neutrino physics can teach QCD is given

Performance Evaluation of Electronic Inductor-Based Adjustable Speed Drives with Respect to Line Current Interharmonics

DEFF Research Database (Denmark)

Soltani, Hamid; Davari, Pooya; Blaabjerg, Frede

2017-01-01

Electronic Inductor (EI)-based front-end rectifiers have a large potential to become the prominent next generation of Active Front End (AFE) topology used in many applications including Adjustable Speed Drives (ASDs) for systems having unidirectional power flow. The EI-based ASD is mostly...... attractive due to its improved harmonic performance compared to a conventional ASD. In this digest, the input currents of the EI-based ASD are investigated and compared with the conventional ASDs with respect to interharmonics, which is an emerging power quality topic. First, the main causes...... of the interharmonic distortions in the ASD applications are analyzed under balanced and unbalanced load conditions. Thereafter, the key role of the EI at the DC stage is investigated in terms of high impedance and current harmonics transfer. Obtained experiments and simulations for both EI-based and conventional ASD...

Multi-application inter-tile synchronization on ultra-high-resolution display walls

KAUST Repository

Nam, Sungwon

2010-01-01

Ultra-high-resolution tiled-display walls are typically driven by a cluster of computers. Each computer may drive one or more displays. Synchronization between the computers is necessary to ensure that animated imagery displayed on the wall appears seamless. Most tiled-display middleware systems are designed around the assumption that only a single application instance is running in the tiled display at a time. Therefore synchronization can be achieved with a simple solution such as a networked barrier. When a tiled display has to support multiple applications at the same time, however, the simple networked barrier approach does not scale. In this paper we propose and experimentally validate two synchronization algorithms to achieve low-latency, intertile synchronization for multiple applications with independently varying frame rates. The two-phase algorithm is more generally applicable to various highresolution tiled display systems. The one-phase algorithm provides superior results but requires support for the Network Time Protocol and is more CPU-intensive. Copyright 2010 ACM.

Differences of Driving Experience and Gender on Traffic Offences Among Malaysian Motorists

Directory of Open Access Journals (Sweden)

Liew Sharifah

2017-01-01

Full Text Available This study attempt to examine the influence of driving experience and gender on different traffic offences. Questionnaire survey was conducted to measure the frequency of committing eleven types of traffic. Data collected were analysed using t-test and Chi-square. Results indicate that male drivers have high score in speeding, red light running, tailgating and using emergency lane. Significant differences emerged between driving experiences in speeding, red light running, dangerously cutting into traffic, using hand phone while driving/riding and driving/riding with noncompliance specification vehicle.

14 CFR 23.253 - High speed characteristics.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false High speed characteristics. 23.253 Section... Requirements § 23.253 High speed characteristics. If a maximum operating speed VMO/MMO is established under § 23.1505(c), the following speed increase and recovery characteristics must be met: (a) Operating...

High-speed particle tracking in microscopy using SPAD image sensors

Science.gov (United States)

Gyongy, Istvan; Davies, Amy; Miguelez Crespo, Allende; Green, Andrew; Dutton, Neale A. W.; Duncan, Rory R.; Rickman, Colin; Henderson, Robert K.; Dalgarno, Paul A.

2018-02-01

Single photon avalanche diodes (SPADs) are used in a wide range of applications, from fluorescence lifetime imaging microscopy (FLIM) to time-of-flight (ToF) 3D imaging. SPAD arrays are becoming increasingly established, combining the unique properties of SPADs with widefield camera configurations. Traditionally, the photosensitive area (fill factor) of SPAD arrays has been limited by the in-pixel digital electronics. However, recent designs have demonstrated that by replacing the complex digital pixel logic with simple binary pixels and external frame summation, the fill factor can be increased considerably. A significant advantage of such binary SPAD arrays is the high frame rates offered by the sensors (>100kFPS), which opens up new possibilities for capturing ultra-fast temporal dynamics in, for example, life science cellular imaging. In this work we consider the use of novel binary SPAD arrays in high-speed particle tracking in microscopy. We demonstrate the tracking of fluorescent microspheres undergoing Brownian motion, and in intra-cellular vesicle dynamics, at high frame rates. We thereby show how binary SPAD arrays can offer an important advance in live cell imaging in such fields as intercellular communication, cell trafficking and cell signaling.

Extreme ultra-violet movie camera for imaging microsecond time scale magnetic reconnection

International Nuclear Information System (INIS)

Chai, Kil-Byoung; Bellan, Paul M.

2013-01-01

An ultra-fast extreme ultra-violet (EUV) movie camera has been developed for imaging magnetic reconnection in the Caltech spheromak/astrophysical jet experiment. The camera consists of a broadband Mo:Si multilayer mirror, a fast decaying YAG:Ce scintillator, a visible light block, and a high-speed visible light CCD camera. The camera can capture EUV images as fast as 3.3 × 10 6 frames per second with 0.5 cm spatial resolution. The spectral range is from 20 eV to 60 eV. EUV images reveal strong, transient, highly localized bursts of EUV radiation when magnetic reconnection occurs

Extreme ultra-violet movie camera for imaging microsecond time scale magnetic reconnection

Energy Technology Data Exchange (ETDEWEB)

Chai, Kil-Byoung; Bellan, Paul M. [Applied Physics, Caltech, 1200 E. California Boulevard, Pasadena, California 91125 (United States)

2013-12-15

An ultra-fast extreme ultra-violet (EUV) movie camera has been developed for imaging magnetic reconnection in the Caltech spheromak/astrophysical jet experiment. The camera consists of a broadband Mo:Si multilayer mirror, a fast decaying YAG:Ce scintillator, a visible light block, and a high-speed visible light CCD camera. The camera can capture EUV images as fast as 3.3 × 10{sup 6} frames per second with 0.5 cm spatial resolution. The spectral range is from 20 eV to 60 eV. EUV images reveal strong, transient, highly localized bursts of EUV radiation when magnetic reconnection occurs.

Optimization design of wind turbine drive train based on Matlab genetic algorithm toolbox

Science.gov (United States)

Li, R. N.; Liu, X.; Liu, S. J.

2013-12-01

In order to ensure the high efficiency of the whole flexible drive train of the front-end speed adjusting wind turbine, the working principle of the main part of the drive train is analyzed. As critical parameters, rotating speed ratios of three planetary gear trains are selected as the research subject. The mathematical model of the torque converter speed ratio is established based on these three critical variable quantity, and the effect of key parameters on the efficiency of hydraulic mechanical transmission is analyzed. Based on the torque balance and the energy balance, refer to hydraulic mechanical transmission characteristics, the transmission efficiency expression of the whole drive train is established. The fitness function and constraint functions are established respectively based on the drive train transmission efficiency and the torque converter rotating speed ratio range. And the optimization calculation is carried out by using MATLAB genetic algorithm toolbox. The optimization method and results provide an optimization program for exact match of wind turbine rotor, gearbox, hydraulic mechanical transmission, hydraulic torque converter and synchronous generator, ensure that the drive train work with a high efficiency, and give a reference for the selection of the torque converter and hydraulic mechanical transmission.

Optimization design of wind turbine drive train based on Matlab genetic algorithm toolbox

International Nuclear Information System (INIS)

Li, R N; Liu, X; Liu, S J

2013-01-01

In order to ensure the high efficiency of the whole flexible drive train of the front-end speed adjusting wind turbine, the working principle of the main part of the drive train is analyzed. As critical parameters, rotating speed ratios of three planetary gear trains are selected as the research subject. The mathematical model of the torque converter speed ratio is established based on these three critical variable quantity, and the effect of key parameters on the efficiency of hydraulic mechanical transmission is analyzed. Based on the torque balance and the energy balance, refer to hydraulic mechanical transmission characteristics, the transmission efficiency expression of the whole drive train is established. The fitness function and constraint functions are established respectively based on the drive train transmission efficiency and the torque converter rotating speed ratio range. And the optimization calculation is carried out by using MATLAB genetic algorithm toolbox. The optimization method and results provide an optimization program for exact match of wind turbine rotor, gearbox, hydraulic mechanical transmission, hydraulic torque converter and synchronous generator, ensure that the drive train work with a high efficiency, and give a reference for the selection of the torque converter and hydraulic mechanical transmission

Sensorless FOC Performance Improved with On-Line Speed and Rotor Resistance Estimator Based on an Artificial Neural Network for an Induction Motor Drive

Directory of Open Access Journals (Sweden)

Jose. M. Gutierrez-Villalobos

2015-06-01

Full Text Available Three-phase induction motor drive requires high accuracy in high performance processes in industrial applications. Field oriented control, which is one of the most employed control schemes for induction motors, bases its function on the electrical parameter estimation coming from the motor. These parameters make an electrical machine driver work improperly, since these electrical parameter values change at low speeds, temperature changes, and especially with load and duty changes. The focus of this paper is the real-time and on-line electrical parameters with a CMAC-ADALINE block added in the standard FOC scheme to improve the IM driver performance and endure the driver and the induction motor lifetime. Two kinds of neural network structures are used; one to estimate rotor speed and the other one to estimate rotor resistance of an induction motor.

An ultra-high-speed direct digital frequency synthesizer implemented in GaAs HBT technology

International Nuclear Information System (INIS)

Chen Gaopeng; Wu Danyu; Jin Zhi; Liu Xinyu

2010-01-01

This paper presents a 10-GHz 8-bit direct digital synthesizer (DDS) microwave monolithic integrated circuit implemented in 1 μm GaAs HBT technology. The DDS takes a double-edge-trigger (DET) 8-stage pipeline accumulator with sine-weighted DAC-based ROM-less architecture, which can maximize the utilization ratio of the GaAs HBT's high-speed potential. With an output frequency up to 5 GHz, the DDS gives an average spurious free dynamic range of 23.24 dBc through the first Nyquist band, and consumes 2.4 W of DC power from a single -4.6 V DC supply. Using 1651 GaAs HBT transistors, the total area of the DDS chip is 2.4 x 2.0 mm 2 . (semiconductor integrated circuits)

High speed photodiodes in standard nanometer scale CMOS technology: a comparative study.

Science.gov (United States)

Nakhkoob, Behrooz; Ray, Sagar; Hella, Mona M

2012-05-07

This paper compares various techniques for improving the frequency response of silicon photodiodes fabricated in mainstream CMOS technology for fully integrated optical receivers. The three presented photodiodes, Spatially Modulated Light detectors, Double, and Interrupted P-Finger photodiodes, aim at reducing the low speed diffusive component of the photo generated current. For the first photodiode, Spatially Modulated Light (SML) detectors, the low speed current component is canceled out by converting it to a common mode current driving a differential transimpedance amplifier. The Double Photodiode (DP) uses two depletion regions to increase the fast drift component, while the Interrupted-P Finger Photodiode (IPFPD) redirects the low speed component towards a different contact from the main fast terminal of the photodiode. Extensive device simulations using 130 nm CMOS technology-parameters are presented to compare their performance using the same technological platform. Finally a new type of photodiode that uses triple well CMOS technology is introduced that can achieve a bandwidth of roughly 10 GHz without any process modification or high reverse bias voltages that would jeopardize the photodetector and subsequent transimpedance amplifier reliability.

Development of Dynamic Compaction Technology for Ultra High Strength Powder Products

International Nuclear Information System (INIS)

Rhee, Chang Kyu; Lee, M. K.; Uhm, Y. R.; Park, J. J.; Lee, J. G.; Ivanov, V. V.; Hong, S. J.

2007-04-01

A synthesis of ultra fine powder and its compaction have been considered as a new generation and high value added technology in various industrial fields such as automobile, machine tool, electronic chip, sensor and catalyst because of its special characteristics of high toughness, strength and wear resistance which are not shown in conventional process. In this study, ultra hard and fine powders, such as Fe-Si, CuNi and Al 2 O 3 , have been fabricated by the pulsed wire evaporation (PWE) method and mechanical alloying (MA) method. In addition, with ultra hard and fine powders, the magnetic core, diamond tool and water jet nozzle with high density were made by a uniaxial dynamic compaction for the purpose of the real industrial application

Ultra high-energy cosmic ray composition

International Nuclear Information System (INIS)

Longley, N.P.

1993-01-01

The Soudan 2 surface-underground cosmic ray experiment can simultaneously measure surface shower size, underground muon multiplicity, and underground muon separation for ultra high energy cosmic ray showers. These measurements are sensitive to the primary composition. Analysis for energies from 10 1 to 10 4 TeV favors a light flux consisting of predominantly H and He nuclei

High-risk driving attitudes and everyday driving violations of car and racing enthusiasts in Ontario, Canada.

Science.gov (United States)

Yildirim-Yenier, Zümrüt; Vingilis, Evelyn; Wiesenthal, David L; Mann, Robert E; Seeley, Jane

2015-01-01

Attitudes and individual difference variables of car and racing enthusiasts regarding high-risk behaviors of street racing and stunt driving have recently been investigated. Positive attitudes toward high-risk driving, personality variables such as driver thrill seeking, and other self-reported risky driving acts were associated with these behaviors. However, probable relationships among high-risk driving tendencies, everyday driving behaviors, and negative road safety outcomes have remained largely unexamined. This study aimed to investigate the associations among car and racing enthusiasts' high-risk driving attitudes, self-reported everyday driving violations (i.e., ordinary and aggressive violations), and self-reported negative outcomes (i.e., collisions and driving offense citations). A web-based survey was conducted with members and visitors of car club and racing websites in Ontario, Canada. Data were obtained from 366 participants. The questionnaire included 4 attitude measures-(1) attitudes toward new penalties for Ontario's Street Racers, Stunt and Aggressive Drivers Legislation; (2) attitudes toward new offenses of stunt driving under the same legislation; (3) general attitudes toward street racing and stunt driving; (4) comparison of street racing with other risky driving behaviors-self-reported driving violations (i.e., ordinary and aggressive violations); self-reported collisions and offense citations; and background and driving questions (e.g., age, driving frequency). Results revealed that attitudes toward stunt driving offenses negatively and general attitudes toward street racing and stunt driving positively predicted ordinary violations, which, in turn, predicted offense citations. Moreover, general attitudes toward street racing and stunt driving positively predicted aggressive violations, which, in turn, predicted offense citations. The findings indicate that positive high-risk driving attitudes may be transferring to driving violations in

Connections in Precast Buildings using Ultra High-Strength Fibre Reinforced Concrete

DEFF Research Database (Denmark)

Hansen, Lars Pilegaard

1995-01-01

Ultra high-strength concrete adds new dimensions to the design of concrete structures. It is a brittle material but introducing fibres into the matrix changes the material into a highly ductile material. Furthermore, the fibre reinforcement increases the anchorage of traditional reinforcement bar...... and the fire resistance. Such a fibre reinforced ultra high-strength material has been used to develop a simple joint solution between slab elements in a column - slab building system....

High-Speed Photography

International Nuclear Information System (INIS)

Paisley, D.L.; Schelev, M.Y.

1998-01-01

The applications of high-speed photography to a diverse set of subjects including inertial confinement fusion, laser surgical procedures, communications, automotive airbags, lightning etc. are briefly discussed. (AIP) copyright 1998 Society of Photo-Optical Instrumentation Engineers

Comparison of Corneal Deformation Parameters in Keratoconic and Normal Eyes Using a Non-contact Tonometer With a Dynamic Ultra-High-Speed Scheimpflug Camera.

Science.gov (United States)

Mercer, Ryan N; Waring, George O; Roberts, Cynthia J; Jhanji, Vishal; Wang, Yumeng; Filho, Joao S; Hemings, Richard A; Rocha, Karolinne M

2017-09-01

To evaluate and compare biomechanical properties in normal and keratoconic eyes using a dynamic ultra-high-speed Scheimpflug camera equipped with a non-contact tonometer (Corvis ST; Oculus Optikgeräte GmbH, Wetzlar, Germany). This retrospective study evaluated 89 eyes (47 normal, 42 keratoconic) and a validation arm of 72 eyes (33 normal, 39 keratoconic) using the Corvis ST. A diagnosis of keratoconus was established by clinical findings confirmed by topography and tomography. Dynamic corneal response parameters collected by the Corvis ST (A1 velocity, deformation amplitude [DA], DA Ratio Max 1mm, and Max Inverse Radius) and a stiffness parameter at first applanation (SP-A1) were incorporated into a novel logistic regression equation (DCR index). Area under the receiver operating curve (AUC) was used to assess the sensitivity and specificity of the DCR index. DA, DA Ratio Max 1mm, Max Inverse Radius, and SP-A1 were each found to be statistically significantly different between normal and keratoconic eyes (Mann-Whitney test [independent samples]; P = .0077, < .0001, < .0001, and < .0001, respectively; significance level: P < .05). DCR index demonstrated high sensitivity, specificity, and overall correct detection rate (92.9%, 95.7%, and 94.4%, respectively; AUC = 98.5). The sensitivity and overall correct detection rate improved when eyes with Topographical Keratoconus Classification grades (TKC) greater than 0 were reevaluated (from 92.9% to 96.6% and from 94.4% to 96.1%, respectively). Combining multiple biomechanical parameters (A1 velocity, DA, DA Ratio Max 1mm, Max Inverse Radius, and SP-A1) into a logistic regression equation allows for high sensitivity and specificity for distinguishing keratoconic from normal eyes. [J Refract Surg. 2017;33(9):625-631.]. Copyright 2017, SLACK Incorporated.

Ultra-light-weight high torque density brushless PM machine design: considering driving-cycle of a four-wheel drive race car (EVER15-138)

NARCIS (Netherlands)

Paulides, J.J.H.; Encica, L.; Beernaert, T.F.; Velden, van der H.H.F.; Parfant, A.G.P.; Lomonova, E.A.

2015-01-01

This paper explores the design of an ultra-light-weight power and torque dense motor to enhance the performance of a light-weight electric racing vehicle. Such a racing vehicle is to compete in formula student racing events. The state-of-the-art powertrain in these vehicles are axial-field machines

Ultra high performance concrete made with rice husk ash for reduced autogenous shrinkage

NARCIS (Netherlands)

Van Breugel, K.; Van Tuan, N.

2014-01-01

Ultra High Strength Concrete (UHPC) is generally made with low w/c mixtures and by adding silica fume. Low w/c mixtures, however, exhibit high autogenous shrinkage, while a high amount of silica fume increases the price of these mixtures. For designing ultra high strength mixtures with low

Influence of high volumes of ultra-fine additions on self-compacting concrete[ACI SP-239

Energy Technology Data Exchange (ETDEWEB)

Cioffi, R. [Naples Univ., Naples (Italy). Faculty of Engineering; Colangelo, F. [Naples Univ., Naples (Italy). Dept. of Technologies; Caputo, D.; Liguori, B. [Naples Univ., Naples (Italy). Dept. of Materials and Production Engineering

2006-07-01

The addition of fine minerals can reduce water demand and increase the slump characteristics of concrete. This paper examined the influence of high volumes of ultra-fine fly ash, raw fly ash, silica fume and natural zeolites on the properties of self-compacting concrete (SCC). Three samples of SCC were prepared using various mineral additions to determine normal slump and J-ring slump flows of fresh concrete as well as the compressive strength and elastic modulus properties of hardened concrete. Cement and crushed limestone natural aggregates were used. The fly ash, silica fume and natural zeolites were subjected to wet high energy milling. The rotating speed, milling time, water-to-solid ratio, and size of milling media were optimized to obtain powders with varying qualities. Results of the study showed that values for the normal slump flow ranged between 604 and 785 mm, while the differences with the J-ring slump flow were less than 30 mm. The samples were then tested to evaluate the mechanical properties of the hardened concrete after 7 and 28 curing days. The modulus of elasticity and compressive strength showed improvements in the concretes containing the ultra-fine fly ash. No segregation phenomena were observed in the case of the cylindrical column specimens. It was concluded that all the specimens provided environmentally sustainable, high workability concretes which can be successfully prepared with the addition of high volumes of minerals. 17 refs., 5 tabs., 6 figs.

Ultra-high field MRI: Advancing systems neuroscience towards mesoscopic human brain function

NARCIS (Netherlands)

Dumoulin, Serge O; Fracasso, A.; Van der Zwaag, W.; Siero, Jeroen C W; Petridou, Natalia

2018-01-01

Human MRI scanners at ultra-high magnetic field strengths of 7 T and higher are increasingly available to the neuroscience community. A key advantage brought by ultra-high field MRI is the possibility to increase the spatial resolution at which data is acquired, with little reduction in image

Full drive-by-wire dynamic control for four-wheel-steer all-wheel-drive vehicles

Science.gov (United States)

Fahimi, Farbod

2013-03-01

Most of the controllers introduced for four-wheel-steer (4WS) vehicles are derived with the assumption that the longitudinal speed of the vehicle is constant. However, in real applications, the longitudinal speed varies, and the longitudinal, lateral, and yaw dynamics are coupled. In this paper, the longitudinal dynamics of the vehicle as well as its lateral and yaw motions are controlled simultaneously. This way, the effect of driving/braking forces of the tires on the lateral and yaw motions of the vehicle are automatically included in the control laws. To address the dynamic parameter uncertainty of the vehicle, a chatter-free variable structure controller is introduced. Elimination of chatter is achieved by introducing a dynamically adaptive boundary layer thickness. It is shown via simulations that the proposed control approach performs more robustly than the controllers developed based on dynamic models, in which longitudinal speed is assumed to be constant, and only lateral speed and yaw rate are used as system states. Furthermore, this approach supports all-wheel-drive vehicles. Front-wheel-drive or rear-wheel-drive vehicles are also supported as special cases of an all-wheel-drive vehicle.

Ultrahigh-speed X-ray imaging of hypervelocity projectiles

Science.gov (United States)

Miller, Stuart; Singh, Bipin; Cool, Steven; Entine, Gerald; Campbell, Larry; Bishel, Ron; Rushing, Rick; Nagarkar, Vivek V.

2011-08-01

High-speed X-ray imaging is an extremely important modality for healthcare, industrial, military and research applications such as medical computed tomography, non-destructive testing, imaging in-flight projectiles, characterizing exploding ordnance, and analyzing ballistic impacts. We report on the development of a modular, ultrahigh-speed, high-resolution digital X-ray imaging system with large active imaging area and microsecond time resolution, capable of acquiring at a rate of up to 150,000 frames per second. The system is based on a high-resolution, high-efficiency, and fast-decay scintillator screen optically coupled to an ultra-fast image-intensified CCD camera designed for ballistic impact studies and hypervelocity projectile imaging. A specially designed multi-anode, high-fluence X-ray source with 50 ns pulse duration provides a sequence of blur-free images of hypervelocity projectiles traveling at speeds exceeding 8 km/s (18,000 miles/h). This paper will discuss the design, performance, and high frame rate imaging capability of the system.

A Delay Time Measurement of ULTRAS (Ultra-high Temperature Ultrasonic Response Analysis System) for a High Temperature Experiment

International Nuclear Information System (INIS)

Koo, Kil Mo; Kim, Sang Baik

2010-01-01

The temperature measurement of very high temperature core melt is of importance in a high temperature as the molten pool experiment in which gap formation between core melt and the reactor lower head, and the effect of the gap on thermal behavior are to be measured. The existing temperature measurement techniques have some problems, which the thermocouple, one of the contact methods, is restricted to under 2000 .deg. C, and the infrared thermometry, one of the non-contact methods, is unable to measure an internal temperature and very sensitive to the interference from reacted gases. In order to solve these problems, the delay time technique of ultrasonic wavelets due to high temperature has two sorts of stage. As a first stage, a delay time measurement of ULTRAS (Ultra-high Temperature Ultrasonic Response Analysis System) is suggested. As a second stage, a molten material temperature was measured up to 2300 .deg. C. Also, the optimization design of the UTS (ultrasonic temperature sensor) with persistence at the high temperature was suggested in this paper. And the utilization of the theory suggested in this paper and the efficiency of the developed system are performed by special equipment and some experiments supported by KRISS (Korea Research Institute of Standard and Science)

SEAL FOR HIGH SPEED CENTRIFUGE

Science.gov (United States)

Skarstrom, C.W.

1957-12-17

A seal is described for a high speed centrifuge wherein the centrifugal force of rotation acts on the gasket to form a tight seal. The cylindrical rotating bowl of the centrifuge contains a closure member resting on a shoulder in the bowl wall having a lower surface containing bands of gasket material, parallel and adjacent to the cylinder wall. As the centrifuge speed increases, centrifugal force acts on the bands of gasket material forcing them in to a sealing contact against the cylinder wall. This arrangememt forms a simple and effective seal for high speed centrifuges, replacing more costly methods such as welding a closure in place.

Offset Compound Gear Inline Two-Speed Drive

Science.gov (United States)

Stevens, Mark A. (Inventor); Handschuh, Robert F. (Inventor); Lewicki, David G. (Inventor)

2014-01-01

A two-speed transmission having an input shaft and an output shaft, the transmission being capable of transitioning between fixed ratios, the high-range ratio being direct 1:1 and the low-range ratio being about 2:1. The transmission is a simple lightweight, yet robust, configuration utilizing only two gear meshes, being comprised of an input gear, a cluster gear, and an output gear. The transmission is controlled with a clutch and a sprag and with the input and output shafts turning in the same direction.

Ultra-high throughput real-time instruments for capturing fast signals and rare events

Science.gov (United States)

Buckley, Brandon Walter

Wide-band signals play important roles in the most exciting areas of science, engineering, and medicine. To keep up with the demands of exploding internet traffic, modern data centers and communication networks are employing increasingly faster data rates. Wide-band techniques such as pulsed radar jamming and spread spectrum frequency hopping are used on the battlefield to wrestle control of the electromagnetic spectrum. Neurons communicate with each other using transient action potentials that last for only milliseconds at a time. And in the search for rare cells, biologists flow large populations of cells single file down microfluidic channels, interrogating them one-by-one, tens of thousands of times per second. Studying and enabling such high-speed phenomena pose enormous technical challenges. For one, parasitic capacitance inherent in analog electrical components limits their response time. Additionally, converting these fast analog signals to the digital domain requires enormous sampling speeds, which can lead to significant jitter and distortion. State-of-the-art imaging technologies, essential for studying biological dynamics and cells in flow, are limited in speed and sensitivity by finite charge transfer and read rates, and by the small numbers of photo-electrons accumulated in short integration times. And finally, ultra-high throughput real-time digital processing is required at the backend to analyze the streaming data. In this thesis, I discuss my work in developing real-time instruments, employing ultrafast optical techniques, which overcome some of these obstacles. In particular, I use broadband dispersive optics to slow down fast signals to speeds accessible to high-bit depth digitizers and signal processors. I also apply telecommunication multiplexing techniques to boost the speeds of confocal fluorescence microscopy. The photonic time stretcher (TiSER) uses dispersive Fourier transformation to slow down analog signals before digitization and

High-Speed Data Recorder for Space, Geodesy, and Other High-Speed Recording Applications

Science.gov (United States)

Taveniku, Mikael

2013-01-01

A high-speed data recorder and replay equipment has been developed for reliable high-data-rate recording to disk media. It solves problems with slow or faulty disks, multiple disk insertions, high-altitude operation, reliable performance using COTS hardware, and long-term maintenance and upgrade path challenges. The current generation data recor - ders used within the VLBI community are aging, special-purpose machines that are both slow (do not meet today's requirements) and are very expensive to maintain and operate. Furthermore, they are not easily upgraded to take advantage of commercial technology development, and are not scalable to multiple 10s of Gbit/s data rates required by new applications. The innovation provides a softwaredefined, high-speed data recorder that is scalable with technology advances in the commercial space. It maximally utilizes current technologies without being locked to a particular hardware platform. The innovation also provides a cost-effective way of streaming large amounts of data from sensors to disk, enabling many applications to store raw sensor data and perform post and signal processing offline. This recording system will be applicable to many applications needing realworld, high-speed data collection, including electronic warfare, softwaredefined radar, signal history storage of multispectral sensors, development of autonomous vehicles, and more.

Ultra-high resolution AMOLED

Science.gov (United States)

Wacyk, Ihor; Prache, Olivier; Ghosh, Amal

2011-06-01

AMOLED microdisplays continue to show improvement in resolution and optical performance, enhancing their appeal for a broad range of near-eye applications such as night vision, simulation and training, situational awareness, augmented reality, medical imaging, and mobile video entertainment and gaming. eMagin's latest development of an HDTV+ resolution technology integrates an OLED pixel of 3.2 × 9.6 microns in size on a 0.18 micron CMOS backplane to deliver significant new functionality as well as the capability to implement a 1920×1200 microdisplay in a 0.86" diagonal area. In addition to the conventional matrix addressing circuitry, the HDTV+ display includes a very lowpower, low-voltage-differential-signaling (LVDS) serialized interface to minimize cable and connector size as well as electromagnetic emissions (EMI), an on-chip set of look-up-tables for digital gamma correction, and a novel pulsewidth- modulation (PWM) scheme that together with the standard analog control provides a total dimming range of 0.05cd/m2 to 2000cd/m2 in the monochrome version. The PWM function also enables an impulse drive mode of operation that significantly reduces motion artifacts in high speed scene changes. An internal 10-bit DAC ensures that a full 256 gamma-corrected gray levels are available across the entire dimming range, resulting in a measured dynamic range exceeding 20-bits. This device has been successfully tested for operation at frame rates ranging from 30Hz up to 85Hz. This paper describes the operational features and detailed optical and electrical test results for the new AMOLED WUXGA resolution microdisplay.

High-speed optical coherence tomography signal processing on GPU

International Nuclear Information System (INIS)

Li Xiqi; Shi Guohua; Zhang Yudong

2011-01-01

The signal processing speed of spectral domain optical coherence tomography (SD-OCT) has become a bottleneck in many medical applications. Recently, a time-domain interpolation method was proposed. This method not only gets a better signal-to noise ratio (SNR) but also gets a faster signal processing time for the SD-OCT than the widely used zero-padding interpolation method. Furthermore, the re-sampled data is obtained by convoluting the acquired data and the coefficients in time domain. Thus, a lot of interpolations can be performed concurrently. So, this interpolation method is suitable for parallel computing. An ultra-high optical coherence tomography signal processing can be realized by using graphics processing unit (GPU) with computer unified device architecture (CUDA). This paper will introduce the signal processing steps of SD-OCT on GPU. An experiment is performed to acquire a frame SD-OCT data (400A-linesx2048 pixel per A-line) and real-time processed the data on GPU. The results show that it can be finished in 6.208 milliseconds, which is 37 times faster than that on Central Processing Unit (CPU).

High-speed precision motion control

CERN Document Server

Yamaguchi, Takashi; Pang, Chee Khiang

2011-01-01

Written for researchers and postgraduate students in Control Engineering, as well as professionals in the Hard Disk Drive industry, this book discusses high-precision and fast servo controls in Hard Disk Drives (HDDs). The editors present a number of control algorithms that enable fast seeking and high precision positioning, and propose problems from commercial products, making the book valuable to researchers in HDDs. Each chapter is self contained, and progresses from concept to technique, present application examples that can be used within automotive, aerospace, aeronautical, and manufactu

MTU underfloor rail drives based on Series 1600 engines

Energy Technology Data Exchange (ETDEWEB)

Bamberger, Norbert; Lieb, Martin; Reich, Christian [MTU Friedrichshafen GmbH, Friedrichshafen (Germany)

2013-05-15

With the heavy demands now being placed on railcar drive systems, ever more powerful solutions are needed. For the new high-speed trains in Britain's Intercity Express Programme (IEP), Hitachi udorses the use of MTU's underfloor drives based on Series 1600 engines.

The high speed civil transport and NASA's High Speed Research (HSR) program

Science.gov (United States)

Shaw, Robert J.

1994-01-01

Ongoing studies being conducted not only in this country but in Europe and Asia suggest that a second generation supersonic transport, or High-Speed Civil Transport (HSCT), could become an important part of the 21st century international air transportation system. However, major environmental compatibility and economic viability issues must be resolved if the HSCT is to become a reality. This talk will overview the NASA High-Speed Research (HSR) program which is aimed at providing the U.S. industry with a technology base to allow them to consider launching an HSCT program early in the next century. The talk will also discuss some of the comparable activities going on within Europe and Japan.

Naturalistic speeding data: Drivers aged 75 years and older

Directory of Open Access Journals (Sweden)

Anna Chevalier

2016-09-01

Full Text Available The data presented in this article are related to the research article entitled “A longitudinal investigation of the predictors of older drivers׳ speeding behavior” (Chevalier et al., 2016 [1], wherein these speed events were used to investigate older drivers speeding behavior and the influence of cognition, vision, functional decline, and self-reported citations and crashes on speeding behavior over a year of driving. Naturalistic speeding behavior data were collected for up to 52 weeks from volunteer drivers aged 75–94 years (median 80 years, 52% male living in the suburban outskirts of Sydney. Driving data were collected using an in-vehicle monitoring device. Global Positioning System (GPS data were recorded at each second and determined driving speed through triangulation of satellite collected location data. Driving speed data were linked with mapped speed zone data based on a service-provider database. To measure speeding behavior, speed events were defined as driving 1 km/h or more, with a 3% tolerance, above a single speed limit, averaged over 30 s. The data contains a row per 124,374 speed events. This article contains information about data processing and quality control. Keywords: Older drivers, Speed, Road safety, Naturalistic, In-vehicle monitoring, Device

Load-Independent Harmonic Mitigation in SCR-Fed Three-Phase Multiple Adjustable Speed Drive Systems with Deliberately Dispatched Firing Angles

DEFF Research Database (Denmark)

Yang, Yongheng; Davari, Pooya; Blaabjerg, Frede

2018-01-01

Adjustable speed drives (ASD) are widely used in industry for energy savings, where low-cost diode rectifiers are still employed as the front-ends, also for simplicity in control and reliability in operation. However, significant harmonics appear at the grid, which should be tackled according...... a harmonic mitigation strategy for multiple ASD systems, where silicon-controlled rectifiers (SCR) with boost converters in the dc-link have been adopted to increase the harmonic-current controllability. More specific, the SCR firing angles are deliberately dispatched among the drive units, which results...

Spalling behavior and residual resistance of fibre reinforced Ultra-High performance concrete after exposure to high temperatures

Directory of Open Access Journals (Sweden)

Xiong, Ming-Xiang

2015-12-01

Full Text Available Experimental results of spalling and residual mechanical properties of ultra-high performance concrete after exposure to high temperatures are presented in this paper. The compressive strength of the ultra-high performance concrete ranged from 160 MPa~185 MPa. This study aimed to discover the effective way to prevent spalling for the ultra-high performance concrete and gauge its mechanical properties after it was subjected to fire. The effects of fiber type, fiber dosage, heating rate and curing condition were investigated. Test results showed that the compressive strength and elastic modulus of the ultra-high performance concrete declined slower than those of normal strength concrete after elevated temperatures. Polypropylene fiber rather than steel fiber was found effective to prevent spalling but affected workability. The effective fiber type and dosage were recommended to prevent spalling and ensure sufficient workability for casting and pumping of the ultra-high performance concrete.En este trabajo se presentan los resultados más relevantes del trabajo experimental realizado para valorar la laminación y las propiedades mecánicas residuales de hormigón de ultra-altas prestaciones tras su exposición a altas temperaturas. La resistencia a la compresión del hormigón de ultra-altas prestaciones osciló entre 160 MPa~185 MPa. El objetivo de este estudio fue descubrir una manera eficaz de prevenir desprendimientos y/o laminaciones en este hormigón y medir sus propiedades mecánicas después de ser sometido al fuego. Las variables estudiadas fueron la presencia y dosificación de fibras, velocidad de calentamiento y condiciones de curado. Los resultados mostraron, tras la exposición a altas temperaturas, que la resistencia a compresión y el módulo de elasticidad del hormigón de ultra-altas prestaciones disminuían más lento que las de un hormigón con resistencia normal. La fibra de polipropileno resultó más eficaz para prevenir

Ultra-high-speed oscillographic techniques; Techniques d'oscillographie ultra-rapide; Metody sverkhskorostnoj ostsillografii; Metodos oscilograficos ultrarrapidos

Energy Technology Data Exchange (ETDEWEB)

Abercrombie, S; Elphick, B; Foster, H [Atomic Weapons Research Establishment, Aldermaston (United Kingdom)

1962-04-15

After a brief history of high-speed transient oscillograph technique, the practical limitations are discussed. A survey of suitable cathode-ray tubes is presented with particular reference to travelling-wave deflection types. The following components of a complete transient signal oscillograph are dealt with: (a) A travelling-wave (TW) deflector cathode-ray tube with balanced co-axial connection, and a bandwidth of 2 GHz; (b) A phase-splitting transformer of 100 and 50-{Omega} characteristic impedance and a bandwidth of 1.5 kHz to 1.5 GHz; (c) Co-axial terminating resistors with GHz performance; (d) Coupling capacitors, compensated for inclusion in co-axial lines for the frequency range 5 kHz - 3 GHz, with characteristic impedances of 100 {Omega}; (e) Wide band resistive pads for the extraction of timebase triggering signals; ( / ) Nanosecond timebases with triggering and blanking facilities; (g) A wide-aperture camera is described. In conclusion, nuclear-electronics applications, are discussed. (author) [French] Apres avoir brievement relate l'evolution de la technique d'emploi des oscillographes transistoires ultra-rapides, le memoire examine les limites de l'application pratique de cette technique. Il passe ensuite en revue les tubes a rayons cathodiques qui se pretent a cet usage en s'attachant plus particulierement aux tubes de deflexion d'ondes progressives. Les auteurs decrivent les elements constitutifs ci-apres des oscillographes a signal transistoire: a) Un tube cathodique de deflexion d'ondes progressives et a connexion equilibree coaxiale; largeur de bande: 2 GHz; b) Un transformateur coupeur de phase d'une impedance caracteristique de 100 et 50 {Omega}; largeur de bande: de 1,5 kHz a 1,5 GHz; c) Des termineurs coaxiaux capables de transmettre des frequences se comptant par GHz; d) Des condensateurs de couplage compenses pour inclusion dans des lignes coaxiales, couvrant la bande de frequences de 5 kHz a 3 GHz et ayant une impedance caracteristique de

Using a High-Speed Camera to Measure the Speed of Sound

Science.gov (United States)

Hack, William Nathan; Baird, William H.

2012-01-01

The speed of sound is a physical property that can be measured easily in the lab. However, finding an inexpensive and intuitive way for students to determine this speed has been more involved. The introduction of affordable consumer-grade high-speed cameras (such as the Exilim EX-FC100) makes conceptually simple experiments feasible. Since the…

Detailed Analysis of Torque Ripple in High Frequency Signal Injection based Sensor less PMSM Drives

Directory of Open Access Journals (Sweden)

Ravikumar Setty A.

2017-01-01

Full Text Available High Frequency Signal Injection based techniques are robust and well proven to estimate the rotor position from stand still to low speed. However, Injected high frequency signal introduces, high frequency harmonics in the motor phase currents and results in significant Output Torque ripple. There is no detailed analysis exist in the literature, to study the effect of injected signal frequency on Torque ripple. Objective of this work is to study the Torque Ripple resulting from High Frequency signal injection in PMSM motor drives. Detailed MATLAB/Simulink simulations are carried to quantify the Torque ripple at different Signal frequencies.

High-speed data acquisition with the Solaris and Linux operating systems

International Nuclear Information System (INIS)

Zilker, M.; Heimann, P.

2000-01-01

In this paper, we discuss whether Solaris and Linux are suitable for data acquisition systems in soft real time conditions. As an example we consider a plasma diagnostic (Mirnov coils), which collects data for a complete plasma discharge of about 10 s from up to 72 channels. Each ADC-Channel generates a data stream of 4 MB/s. To receive these data streams an eight-channel Hotlink PCI interface board was designed. With a prototype system using Solaris and the driver developed by us we investigate important properties of the operating system such as the I/O performance and scheduling of processes. We compare the Solaris operating system on the Ultra Sparc platform with Linux on the Intel platform. Finally, some points of user program development are mentioned to show how the application can make the most efficient use of the underlying high-speed I/O system

33 CFR 84.24 - High-speed craft.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false High-speed craft. 84.24 Section... RULES ANNEX I: POSITIONING AND TECHNICAL DETAILS OF LIGHTS AND SHAPES § 84.24 High-speed craft. (a) The masthead light of high-speed craft with a length to breadth ratio of less than 3.0 may be placed at a...

Neurocognitive performance of a community-based sample of young people at putative ultra high risk for psychosis: support for the processing speed hypothesis.

LENUS (Irish Health Repository)

Kelleher, Ian

2013-01-01

A wide variety of neurocognitive deficits have been reported for help-seeking individuals who are at clinical or ultra high risk for psychosis based on fulfilling set criteria for prodromal syndromes\\/at risk mental states. We wished to extend this research by conducting the first population-based assessment of prodromal syndromes and associated neurocognition.

Synthesis of ultra-long cadmium telluride nanotubes via combinational chemical transformation

Energy Technology Data Exchange (ETDEWEB)

Park, Kee-Ryung; Cho, Hong-Baek; Choa, Yong-Ho, E-mail: choa15@hanyang.ac.kr

2017-03-01

Synthesis of high-throughput cadmium telluride (CdTe) nanotubes with an ultra-long aspect ratio is presented via a combination process concept combined with electrospinning, electrodeposition, and cationic exchange reaction. Ultra-long sacrificial silver (Ag) nanofibers were synthesized by electrospinning involving two-step calcination, and were then electrodeposited to create silver telluride nanotubes. These nanotubes underwent cationic exchange reaction in cadmium nitrate tetrahydrate solution with the aid of a ligand, tributylphosphine (TBP). Analysis showed that ultra-long pure zinc blende CdTe nanotubes were obtained with controlled dimension and uniform morphology. The thermodynamic driving force induced by the coordination of methanol solvent and TBP attributed to overcome the kinetic barrier between Ag{sub 2}Te and CdTe nanotubes, facilitating the synthesis of CdTe nanotubes. This synthetic process involving a topotactic reaction route paves a way for high-throughput extended synthesis of new chalcogenide hollow nanotubes for application in photodetectors and solar cells. - Highlights: • High throughput synthetic route of hollow CdTe nanotubes with ultra-long aspect ratio. • Chemical combination of electrospinning, electrodeposition & cation exchange reaction. • Pure zinc blende CdTe by controlled dimension & structural variation of Ag nanofibers. • Potential for the high throughput synthesis of new exotic chalcogenide nanotubes.

Ultra-high pressure water jet: Baseline report

International Nuclear Information System (INIS)

1997-01-01

The ultra-high pressure waterjet technology was being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU's evaluation of efficiency and cost, this report covers the evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The ultra-high pressure waterjet technology acts as a cutting tool for the removal of surface substrates. The Husky trademark pump feeds water to a lance that directs the high pressure water at the surface to be removed. The safety and health evaluation during the testing demonstration focused on two main areas of exposure. These were dust and noise. The dust exposure was found to be minimal, which would be expected due to the wet environment inherent in the technology, but noise exposure was at a significant level. Further testing for noise is recommended because of the outdoor environment where the testing demonstration took place. In addition, other areas of concern found were arm-hand vibration, ergonomics, heat stress, tripping hazards, electrical hazards, lockout/tagout, fall hazards, slipping hazards, hazards associated with the high pressure water, and hazards associated with air pressure systems

Modified Hermite Pulse-Based Wideband Communication for High-Speed Data Transfer in Wireless Sensor Applications

Directory of Open Access Journals (Sweden)

Kushal P. Pradhan

2017-12-01

Full Text Available With technological advances in the field of communication, the need for reliable high-speed data transfer is increasing. The deployment of large number of wireless sensors for remote monitoring and control and streaming of high definition video, voice and image data, etc. are imposing a challenge to the existing network bandwidth allocation for reliable communication. Two novel schemes for ultra-wide band (UWB communication technology have been proposed in this paper with the key objective of intensifying the data rate by taking advantage of the orthogonal properties of the modified Hermite pulse (MHP. In the first scheme, a composite pulse is transmitted and in the second scheme, a sequence of multi-order orthogonal pulses is transmitted in the place of a single UWB pulse. The MHP pulses exhibit a mutually orthogonal property between different ordered pulses and due to this property, simultaneous transmission is achieved without collision in the UWB system, resulting in an increase in transmission capacity or improved bit error rate. The proposed schemes for enhanced data rate will offer high volume data monitoring, assessment, and control of wireless devices without overburdening the network bandwidth and pave the way for new platforms for future high-speed wireless sensor applications.

Modern trends in designing high-speed trains

Directory of Open Access Journals (Sweden)

Golubović Snežana D.

2015-01-01

Full Text Available Increased advantages of railway transportation systems over other types of transportation systems in the past sixty years have been a result of an intensive development of the new generations of high-speed trains. Not only do these types of trains comply with the need for increased speed of transportation and make the duration of the journey shorter, but they also meet the demands for increased reliability, safety and direct application of energy efficiency to the transportation system itself. Along with increased train speed, the motion resistance is increased as well, whereby at speeds over 200 km/h the proportion of air resistance becomes the most dominant member. One of the most efficient measures for reducing air resistance, as well as other negative consequences of high-speed motion, is the development of the aerodynamic shape of the train. This paper presents some construction solutions that affect the aerodynamic properties of high-speed trains, first and foremost, the nose shape, as well as the similarities and differences of individual subsystems necessary for the functioning of modern high-speed rail systems. We analysed two approaches to solving the problem of the aerodynamic shape of the train and the appropriate infrastructure using the examples of Japan and France. Two models of high-speed trains, Shinkansen (Japan and TGV, i.e. AGV (France, have been discussed.

Measures for speed management.

NARCIS (Netherlands)

2009-01-01

Measures for speed management are essential for limiting the negative effects of driving too fast and at inappropriate speeds. To begin with, safe and credible speed limits need to be determined. Dynamic and variable speed limits that take into account the current circumstances, such as weather

Changes of indicators of high-speed and high-speed and power preparedness at volleyball players of 12–13 years old

Directory of Open Access Journals (Sweden)

Oleg Shevchenko

2016-04-01

Full Text Available Purpose: to define changes of indicators of high-speed and high-speed and power preparedness of volleyball players of 12–13 years old. Material & Methods: the test exercises, which are recommended by the training program of CYSS on volleyball, were used for the definition of the level of development of high-speed and high-speed and power abilities of volleyball players. 25 young volleyball players from the group of the previous basic preparation took part in the experiment. Sports experience of sportsmen is 3–4 years. The analysis of scientifically-methodical literature, pedagogical testing, pedagogical experiment, methods of mathematical statistics were carried out. Results: the analyzed level of high-speed and high-speed and power abilities of volleyball players. Conclusions: the results had reliable changes (t=2,2–2,4 at р<0,05 of the level of high-speed and high-speed and power abilities of volleyball players of 12–13years old in the experimental group at the end of the experiment, except run on 30 m that demonstrates a positive influence of application of special exercises in the educational-training process.

FY 1999 report on the results of the R and D of femtosecond technology. Development of ultra-short pulse optoelectronics technology; 1999 nendo femutobyo technology no kenkyu kaihatsu seika hokokusho. Chotan pulse hikari electronics gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The paper described the FY 1999 results of the R and D of femtosecond technology. For the purpose of creating new industrial basement technology which supports the highly information-oriented society in the 21st century, the ultra-high speed electronics technology is indispensable which is beyond speed limits of the existing electronics technology and has new functionality. The ultra-high speed electronics basement technology is established through the R and D of the technology to control the state of light and electronics in the femtosecond time domain (10{sup -15} - 10{sup -12} second). Themes of the R and D are technology to generate/transmit femtosecond optical pulse, technology for control/distribution, and ultra-short pulse optoelectronics common basement technology. In FY 1999, a lot of results were obtained in the following: generation of the pulse train highly repeated at 500GHz in semiconductor laser; 139km transmission of 250fs optical pulse; switching movement at ultra-high speed of 150fs-1.2ps in transition among subbands of GaN base and Sb base materials; DEMUXA movement toward 160-10Gb/s in Mach-Zehnder type optical switch. (NEDO)

Reducing Heating In High-Speed Cinematography

Science.gov (United States)

Slater, Howard A.

1989-01-01

Infrared-absorbing and infrared-reflecting glass filters simple and effective means for reducing rise in temperature during high-speed motion-picture photography. "Hot-mirror" and "cold-mirror" configurations, employed in projection of images, helps prevent excessive heating of scenes by powerful lamps used in high-speed photography.

High speed data acquisition

International Nuclear Information System (INIS)

Cooper, P.S.

1997-07-01

A general introduction to high speed data acquisition system techniques in modern particle physics experiments is given. Examples are drawn from the SELEX(E78 1) high statistics charmed baryon production and decay experiment now taking data at Fermilab

Tse computers. [ultrahigh speed optical processing for two dimensional binary image

Science.gov (United States)

Schaefer, D. H.; Strong, J. P., III

1977-01-01

An ultra-high-speed computer that utilizes binary images as its basic computational entity is being developed. The basic logic components perform thousands of operations simultaneously. Technologies of the fiber optics, display, thin film, and semiconductor industries are being utilized in the building of the hardware.

Laser surface modification of ultra-high-molecular-weight polyethylene (UHMWPE) for biomedical applications

International Nuclear Information System (INIS)

Riveiro, A.; Soto, R.; Val, J. del; Comesaña, R.; Boutinguiza, M.; Quintero, F.; Lusquiños, F.; Pou, J.

2014-01-01

Ultra-high-molecular-weight polyethylene (UHMWPE) is a synthetic polymer used for biomedical applications because of its high impact resistance, ductility and stability in contact with physiological fluids. Therefore, this material is being used in human orthopedic implants such as total hip or knee replacements. Surface modification of this material relates to changes on its chemistry, microstructure, roughness, and topography, all influencing its biological response. Surface treatment of UHMWPE is very difficult due to its high melt viscosity. This work presents a systematic approach to discern the role of different laser wavelengths (λ = 1064, 532, and 355 nm) on the surface modification of carbon coated UHMWPE samples. Influence of laser processing conditions (irradiance, pulse frequency, scanning speed, and spot overlapping) on the surface properties of this material was determined using an advanced statistical planning of experiments. A full factorial design of experiments was used to find the main effects of the processing parameters. The obtained results indicate the way to maximize surface properties which largely influence cell–material interaction.

Laser surface modification of ultra-high-molecular-weight polyethylene (UHMWPE) for biomedical applications

Energy Technology Data Exchange (ETDEWEB)

Riveiro, A., E-mail: ariveiro@uvigo.es [Applied Physics Department, University of Vigo, ETSII, Lagoas-Marcosende, 9, Vigo 36310 (Spain); Centro Universitario de la Defensa, Escuela Naval Militar, Plaza de España 2, 36920 Marín (Spain); Soto, R.; Val, J. del; Comesaña, R.; Boutinguiza, M.; Quintero, F.; Lusquiños, F.; Pou, J. [Applied Physics Department, University of Vigo, ETSII, Lagoas-Marcosende, 9, Vigo 36310 (Spain)

2014-05-01

Ultra-high-molecular-weight polyethylene (UHMWPE) is a synthetic polymer used for biomedical applications because of its high impact resistance, ductility and stability in contact with physiological fluids. Therefore, this material is being used in human orthopedic implants such as total hip or knee replacements. Surface modification of this material relates to changes on its chemistry, microstructure, roughness, and topography, all influencing its biological response. Surface treatment of UHMWPE is very difficult due to its high melt viscosity. This work presents a systematic approach to discern the role of different laser wavelengths (λ = 1064, 532, and 355 nm) on the surface modification of carbon coated UHMWPE samples. Influence of laser processing conditions (irradiance, pulse frequency, scanning speed, and spot overlapping) on the surface properties of this material was determined using an advanced statistical planning of experiments. A full factorial design of experiments was used to find the main effects of the processing parameters. The obtained results indicate the way to maximize surface properties which largely influence cell–material interaction.

Speed Choice and Curve Radius on Rural Roads

DEFF Research Database (Denmark)

Rimme, Nicolai; Nielsen, Lea; Kjems, Erik

2016-01-01

with informative speed-calming measures as traffic signs, reflectors or surface painting. However, it has been the hypothesis that people are reducing their speed insufficiently and are driving too fast in most curved alignments – especially when they are driving there frequently. By knowing the speed near...... and in the curved alignments compared to the geometry of the curved alignments, it can be clarified, if and which speed-calming measures that are required. Using GNSS-based floating car data (FCD) from driving cars the speed near and in curved alignments is found. Single observation of FCD are connected to trips...

Wake flow characteristics at high wind speed

DEFF Research Database (Denmark)

Aagaard Madsen, Helge; Larsen, Torben J.; Larsen, Gunner Chr.

2016-01-01

Wake flow characteristic at high wind speeds is the main subject of this paper. Although the wake losses decrease at high wind speeds it has been found in a recent study that for multiple wake inflow the increase in loading due to wake effects are substantial even at wind speeds well above rated ...

Ultra Fast, High Rep Rate, High Voltage Spark Gap Pulser

Science.gov (United States)

1995-07-01

current rise time. The spark gap was designed to have a coaxial geometry reducing its inductance. Provisions were made to pass flowing gas between the...ULTRA FAST, HIGH REP RATE, HIGH VOLTAGE SPARK GAP PULSER Robert A. Pastore Jr., Lawrence E. Kingsley, Kevin Fonda, Erik Lenzing Electrophysics and...Modeling Branch AMSRL-PS-EA Tel.: (908)-532-0271 FAX: (908)-542-3348 U.S. Army Research Laboratory Physical Sciences Directorate Ft. Monmouth

Fast and sensitive analysis of beta blockers by ultra-high-performance liquid chromatography coupled with ultra-high-resolution TOF mass spectrometry.

Science.gov (United States)

Tomková, Jana; Ondra, Peter; Kocianová, Eva; Václavík, Jan

2017-07-01

This paper presents a method for the determination of acebutolol, betaxolol, bisoprolol, metoprolol, nebivolol and sotalol in human serum by liquid-liquid extraction and ultra-high-performance liquid chromatography coupled with ultra-high-resolution TOF mass spectrometry. After liquid-liquid extraction, beta blockers were separated on a reverse-phase analytical column (Acclaim RS 120; 100 × 2.1 mm, 2.2 μm). The total run time was 6 min for each sample. Linearity, limit of detection, limit of quantification, matrix effects, specificity, precision, accuracy, recovery and sample stability were evaluated. The method was successfully applied to the therapeutic drug monitoring of 108 patients with hypertension. This method was also used for determination of beta blockers in 33 intoxicated patients. Copyright © 2016 John Wiley & Sons, Ltd.

Speed control at low wind speeds for a variable speed fixed pitch wind turbine

Energy Technology Data Exchange (ETDEWEB)

Rosmin, N.; Watson, S.J.; Tompson, M. [Loughborough Univ., Loughborough, Leicestershire (United Kingdom)

2010-03-09

The maximum power regulation below rated wind speed is regulated by changing the rotor/generator speed at large frequency range in a fixed pitch, variable speed, stall-regulated wind turbine. In order to capture the power at a maximum value the power coefficient is kept at maximum peak point by maintaining the tip speed ratio at its optimum value. The wind industry is moving from stall regulated fixed speed wind turbines to newer improved innovative versions with better reliability. While a stall regulated fixed pitch wind turbine is among the most cost-effective wind turbine on the market, its problems include noise, severe vibrations, high thrust loads and low power efficiency. Therefore, in order to improve such drawbacks, the rotation of the generator speed is made flexible where the rotation can be controlled in variable speed. This paper discussed the development of a simulation model which represented the behaviour of a stall regulated variable speed wind turbine at low wind speed control region by using the closed loop scalar control with adjustable speed drive. The paper provided a description of each sub-model in the wind turbine system and described the scalar control of the induction machine. It was concluded that by using a constant voltage/frequency ratio of the generator's stator side control, the generator speed could be regulated and the generator torque could be controlled to ensure the power coefficient could be maintained close to its maximum value. 38 refs., 1 tab., 10 figs.

Status of Ultra-High Energy Cosmic Rays

CERN Multimedia

CERN. Geneva

2015-01-01

I will review the recent results on Ultra-High energy cosmic rays obtained by the Auger and Telescope Array Observatories, and discuss some of the Astrophysical scenarios that could account for them, a connection with LHC results  as well as the possible connections to neutrino and gamma ray observations.

Parametric tests of a traction drive retrofitted to an automotive gas turbine

Science.gov (United States)

Rohn, D. A.; Lowenthal, S. H.; Anderson, N. E.

1980-01-01

The results of a test program to retrofit a high performance fixed ratio Nasvytis Multiroller Traction Drive in place of a helical gear set to a gas turbine engine are presented. Parametric tests up to a maximum engine power turbine speed of 45,500 rpm and to a power level of 11 kW were conducted. Comparisons were made to similar drives that were parametrically tested on a back-to-back test stand. The drive showed good compatibility with the gas turbine engine. Specific fuel consumption of the engine with the traction drive speed reducer installed was comparable to the original helical gearset equipped engine.

Performance evaluation of a high-speed switched network for PACS

Science.gov (United States)

Zhang, Randy H.; Tao, Wenchao; Huang, Lu J.; Valentino, Daniel J.

1998-07-01

We have replaced our shared-media Ethernet and FDDI network with a multi-tiered, switched network using OC-12 (622 Mbps) ATM for the network backbone, OC3 (155 Mbps) connections to high-end servers and display workstations, and switched 100/10 Mbps Ethernet for workstations and desktop computers. The purpose of this research was to help PACS designers and implementers understand key performance factors in a high- speed switched network by characterizing and evaluating its image delivery performance, specifically, the performance of socket-based TCP (Transmission Control Protocol) and DICOM 3.0 communications. A test network within the UCLA Clinical RIS/PACS was constructed using Sun UltraSPARC-II machines with ATM, Fast Ethernet, and Ethernet network interfaces. To identify performance bottlenecks, we evaluated network throughput for memory to memory, memory to disk, disk to memory, and disk to disk transfers. To evaluate the effect of file size, tests involving disks were further divided using sizes of small (514 KB), medium (8 MB), and large (16 MB) files. The observed maximum throughput for various network configurations using the TCP protocol was 117 Mbps for memory to memory and 88 MBPS for memory to disk. For disk to memory, the peak throughput was 98 Mbps using small files, 114 Mbps using medium files, and 116 Mbps using large files. The peak throughput for disk to disk became 64 Mbps using small files and 96 Mbps using medium and large files. The peak throughput using the DICOM 3.0 protocol was substantially lower in all categories. The measured throughput varied significantly among the tests when TCP socket buffer was raised above the default value. The optimal buffer size was approximately 16 KB or the TCP protocol and around 256 KB for the DICOM protocol. The application message size also displayed distinctive effects on network throughput when the TCP socket buffer size was varied. The throughput results for Fast Ethernet and Ethernet were expectedly

Imaging Frontostriatal Function in Ultra-High-Risk, Early, and Chronic Schizophrenia During Executive Processing

Science.gov (United States)

Morey, Rajendra A.; Inan, Seniha; Mitchell, Teresa V.; Perkins, Diana O.; Lieberman, Jeffrey A.; Belger, Aysenil

2009-01-01

Context Individuals experiencing prodromal symptoms of schizophrenia (ultra-high-risk group) demonstrate impaired performance on tasks of executive function, attention, and working memory. The neurobiological underpinnings of such executive deficits in ultra-high-risk individuals remains unclear. Objective We assessed frontal and striatal functions during a visual oddball continuous performance task, in ultra-high-risk, early, and chronic schizophrenic patients with the use of functional magnetic resonance imaging. Design Cross-sectional case-control design. Setting Community; outpatient clinic. Patients Fifty-two individuals (control, n = 16; ultra-high risk, n = 10; early, n = 15; chronic, n = 11) from a referred clinical sample and age- and sex-matched control volunteers underwent scanning. Main Outcome Measures Percentage of active voxels and percentage signal change calculated for the anterior cingulate gyrus (ACG), middle frontal gyrus (MFG), inferior frontal gyrus (IFG), basal ganglia, and thalamus. Performance on the visual oddball task was measured with percentage of hits and d′ (a measure based on the hit rate and the false-alarm rate). Results The ultra-high-risk group showed significantly smaller differential activation between task-relevant and task-irrelevant stimuli in the frontal regions (ACG, IFG, MFG) than the control group. Frontostriatal activation associated with target stimuli in the early and chronic groups was significantly lower than the control group, while the ultra-high-risk group showed a trend toward the early group. Conclusions Our findings suggest that prefrontal function begins to decline before the onset of syndromally defined illness and hence may represent a vulnerability marker in assessing the risk of developing psychotic disorders among ultra-high-risk individuals. PMID:15753238

High Heat Load Properties of Ultra Fine Grain Tungsten

International Nuclear Information System (INIS)

Zhou, Z.; Du, J.; Ge, C.; Linke, J.; Pintsuk, G.; Song, S.X.

2007-01-01

Full text of publication follows: Tungsten is increasingly considered as a promising candidate armour materials facing the plasma in tokamaks for medium to high heat flux components (EAST, ASDEX, ITER). Fabrication tungsten with ultra fine grain size is considered as an effective way to ameliorate some disadvantages of tungsten, such as its brittleness at room temperature. But the research data on the performance of ultra fine grain tungsten is still very limit. In this work, high heat load properties of pure ultra-fine grain tungsten have been studied. The ultra fine grain tungsten samples with average grain size of 0.2 μm, 1 μm and 3 μm were fabricated by resistance sintering under ultra high pressure. The annealing experiments for the investigation of the material resistance against grain growth have been done by annealing samples in a vacuum furnace at different temperature holding for 2 hours respectively. It is found that recrystallization and grain growth occur at heating temperature of 1250 deg. c. The finer the initial grain sizes of tungsten, the smaller its grain growth grain. The effects of transient high thermal loads (off normal events like disruptions) on tungsten surface morphology have been performed in electron beam test facility JUDITH. The thermal loads tests have been carried out with 4 ms pulses at different power density of 0.22, 0.33, 0.44, 0.55 and 0.88 GW/m 2 respectively. Horizontal cracks formed for all tungsten samples at 0.44 GW/m 2 . Particle erosions occurred for tungsten with 3 μm size at 0.33 GW/m 2 and for tungsten with 0.2 and 1 μm size at 0.55 GW/m 2 . The weight loss of tungsten with 0.2, 1 and 3 μm size are 2,0.1,0.6 mg respectively at 0.88 GW/m 2 . The effects of a large number of very short transient repetitive thermal loads (ELM-like) on tungsten surface morphology also have been performed by using a fundamental wave of a YAG laser. It is found that tungsten with 0.2 μm size has the best performance. (authors)

High Heat Load Properties of Ultra Fine Grain Tungsten

Energy Technology Data Exchange (ETDEWEB)

Zhou, Z.; Du, J.; Ge, C. [Lab. of Special Ceramic and P/M, University of Science and Technology, 100083 Beijing (China); Linke, J.; Pintsuk, G. [FZJ-Forschungszentrum Juelich GmbH, Association Euratom-FZJ, Institut fur Plasmaphysik, Postfach 1913, D-52425 Juelich (Germany); Song, S.X. [Research Center on Fusion Materials (RCFM), University of Science and Technology Beijing (USTB), 100083 Beijing (China)

2007-07-01

Full text of publication follows: Tungsten is increasingly considered as a promising candidate armour materials facing the plasma in tokamaks for medium to high heat flux components (EAST, ASDEX, ITER). Fabrication tungsten with ultra fine grain size is considered as an effective way to ameliorate some disadvantages of tungsten, such as its brittleness at room temperature. But the research data on the performance of ultra fine grain tungsten is still very limit. In this work, high heat load properties of pure ultra-fine grain tungsten have been studied. The ultra fine grain tungsten samples with average grain size of 0.2 {mu}m, 1 {mu}m and 3 {mu}m were fabricated by resistance sintering under ultra high pressure. The annealing experiments for the investigation of the material resistance against grain growth have been done by annealing samples in a vacuum furnace at different temperature holding for 2 hours respectively. It is found that recrystallization and grain growth occur at heating temperature of 1250 deg. c. The finer the initial grain sizes of tungsten, the smaller its grain growth grain. The effects of transient high thermal loads (off normal events like disruptions) on tungsten surface morphology have been performed in electron beam test facility JUDITH. The thermal loads tests have been carried out with 4 ms pulses at different power density of 0.22, 0.33, 0.44, 0.55 and 0.88 GW/m{sup 2} respectively. Horizontal cracks formed for all tungsten samples at 0.44 GW/m{sup 2}. Particle erosions occurred for tungsten with 3 {mu}m size at 0.33 GW/m{sup 2} and for tungsten with 0.2 and 1 {mu}m size at 0.55 GW/m{sup 2}. The weight loss of tungsten with 0.2, 1 and 3 {mu}m size are 2,0.1,0.6 mg respectively at 0.88 GW/m{sup 2}. The effects of a large number of very short transient repetitive thermal loads (ELM-like) on tungsten surface morphology also have been performed by using a fundamental wave of a YAG laser. It is found that tungsten with 0.2 {mu}m size has

14 CFR 25.253 - High-speed characteristics.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false High-speed characteristics. 25.253 Section...-speed characteristics. (a) Speed increase and recovery characteristics. The following speed increase and recovery characteristics must be met: (1) Operating conditions and characteristics likely to cause...

Chicago-St. Louis high speed rail plan

International Nuclear Information System (INIS)

Stead, M.E.

1994-01-01

The Illinois Department of Transportation (IDOT), in cooperation with Amtrak, undertook the Chicago-St. Louis High Speed Rail Financial and Implementation Plan study in order to develop a realistic and achievable blueprint for implementation of high speed rail in the Chicago-St. Louis corridor. This report presents a summary of the Price Waterhouse Project Team's analysis and the Financial and Implementation Plan for implementing high speed rail service in the Chicago-St. Louis corridor

Chicago-St. Louis high speed rail plan

Energy Technology Data Exchange (ETDEWEB)

Stead, M.E.

1994-12-31

The Illinois Department of Transportation (IDOT), in cooperation with Amtrak, undertook the Chicago-St. Louis High Speed Rail Financial and Implementation Plan study in order to develop a realistic and achievable blueprint for implementation of high speed rail in the Chicago-St. Louis corridor. This report presents a summary of the Price Waterhouse Project Team`s analysis and the Financial and Implementation Plan for implementing high speed rail service in the Chicago-St. Louis corridor.

High rate response of ultra-high-performance fiber-reinforced concretes under direct tension

Energy Technology Data Exchange (ETDEWEB)

Tran, Ngoc Thanh [Department of Civil and Environmental Engineering, Sejong University, 98 Gunja-Dong, Gwangjin-Gu, Seoul 143-747 (Korea, Republic of); Tran, Tuan Kiet [Department of Civil and Environmental Engineering, Sejong University, 98 Gunja-Dong, Gwangjin-Gu, Seoul 143-747 (Korea, Republic of); Department of Civil Engineering and Applied Mechanics, Ho Chi Minh City University of Technology and Education, 01 Vo Van Ngan, Thu Duc District, Ho Chi Minh City (Viet Nam); Kim, Dong Joo, E-mail: djkim75@sejong.ac.kr [Department of Civil and Environmental Engineering, Sejong University, 98 Gunja-Dong, Gwangjin-Gu, Seoul 143-747 (Korea, Republic of)

2015-03-15

The tensile response of ultra-high-performance fiber-reinforced concretes (UHPFRCs) at high strain rates (5–24 s{sup −} {sup 1}) was investigated. Three types of steel fibers, including twisted, long and short smooth steel fibers, were added by 1.5% volume content in an ultra high performance concrete (UHPC) with a compressive strength of 180 MPa. Two different cross sections, 25 × 25 and 25 × 50 mm{sup 2}, of tensile specimens were used to investigate the effect of the cross section area on the measured tensile response of UHPFRCs. Although all the three fibers generated strain hardening behavior even at high strain rates, long smooth fibers produced the highest tensile resistance at high rates whereas twisted fiber did at static rate. The breakages of twisted fibers were observed from the specimens tested at high strain rates unlike smooth steel fibers. The tensile behavior of UHPFRCs at high strain rates was clearly influenced by the specimen size, especially in post-cracking strength.

Lubrication and cooling for high speed gears

Science.gov (United States)

Townsend, D. P.

1985-01-01

The problems and failures occurring with the operation of high speed gears are discussed. The gearing losses associated with high speed gearing such as tooth mesh friction, bearing friction, churning, and windage are discussed with various ways shown to help reduce these losses and thereby improve efficiency. Several different methods of oil jet lubrication for high speed gearing are given such as into mesh, out of mesh, and radial jet lubrication. The experiments and analytical results for the various methods of oil jet lubrication are shown with the strengths and weaknesses of each method discussed. The analytical and experimental results of gear lubrication and cooling at various test conditions are presented. These results show the very definite need of improved methods of gear cooling at high speed and high load conditions.

X-ray system with coupled source drive and detector drive

International Nuclear Information System (INIS)

1976-01-01

An electronic coupling replacing the (more expensive) mechanical coupling which controls the speed of two sets of two electric motors, one driving an X-ray source and the other an X-ray detector, is described. Source and detector are kept rotating in parallel planes with a fairly constant velocity ratio. The drives are controlled by an electronic system comprising a comparator circuit comparing the position-indicative signals, a process control circuit and an inverter switch. The control system regulates the speed of the electric motors. The signal processing is described

Control rod drives

International Nuclear Information System (INIS)

Asano, Hiromitsu.

1979-01-01

Purpose: To drive control rods at an optimum safety speed corresponding to the reactor core output. Constitution: The reactor power is detected by a neutron detector and the output signal is applied to a process computer. The process computer issues a signal representing the reactor core output, which is converted through a function generator into a signal representing the safety speed of control rods. The converted signal is further supplied to a V/F converter and converted into a pulse signal. The pulse signal is inputted to a step motor driving circuit, which actuates a step motor to operate the control rods always at a safety speed corresponding to the reactor core power. (Furukawa, Y.)

Application of Boost Converter for Ride-through Capability of Adjustable Speed Drives during Sag and Swell Conditions

OpenAIRE

S. S. Deswal; Ratna Dahiya; D. K. Jain

2008-01-01

Process control and energy conservation are the two primary reasons for using an adjustable speed drive. However, voltage sags are the most important power quality problems facing many commercial and industrial customers. The development of boost converters has raised much excitement and speculation throughout the electric industry. Now utilities are looking to these devices for performance improvement and reliability in a variety of areas. Examples of these include sags,...

The use of high-speed imaging in education

Science.gov (United States)

Kleine, H.; McNamara, G.; Rayner, J.

2017-02-01

Recent improvements in camera technology and the associated improved access to high-speed camera equipment have made it possible to use high-speed imaging not only in a research environment but also specifically for educational purposes. This includes high-speed sequences that are created both with and for a target audience of students in high schools and universities. The primary goal is to engage students in scientific exploration by providing them with a tool that allows them to see and measure otherwise inaccessible phenomena. High-speed imaging has the potential to stimulate students' curiosity as the results are often surprising or may contradict initial assumptions. "Live" demonstrations in class or student- run experiments are highly suitable to have a profound influence on student learning. Another aspect is the production of high-speed images for demonstration purposes. While some of the approaches known from the application of high speed imaging in a research environment can simply be transferred, additional techniques must often be developed to make the results more easily accessible for the targeted audience. This paper describes a range of student-centered activities that can be undertaken which demonstrate how student engagement and learning can be enhanced through the use of high speed imaging using readily available technologies.

Fundamental limitations on 'warp drive' spacetimes

International Nuclear Information System (INIS)

Lobo, Francisco S N; Visser, Matt

2004-01-01

'Warp drive' spacetimes are useful as 'gedanken-experiments' that force us to confront the foundations of general relativity, and among other things, to precisely formulate the notion of 'superluminal' communication. After carefully formulating the Alcubierre and Natario warp drive spacetimes, and verifying their non-perturbative violation of the classical energy conditions, we consider a more modest question and apply linearized gravity to the weak-field warp drive, testing the energy conditions to first and second orders of the warp-bubble velocity, v. Since we take the warp-bubble velocity to be non-relativistic, v << c, we are not primarily interested in the 'superluminal' features of the warp drive. Instead we focus on a secondary feature of the warp drive that has not previously been remarked upon-the warp drive (if it could be built) would be an example of a 'reaction-less drive'. For both the Alcubierre and Natario warp drives we find that the occurrence of significant energy condition violations is not just a high-speed effect, but that the violations persist even at arbitrarily low speeds. A particularly interesting feature of this construction is that it is now meaningful to think of placing a finite mass spaceship at the centre of the warp bubble, and then see how the energy in the warp field compares with the mass-energy of the spaceship. There is no hope of doing this in Alcubierre's original version of the warp field, since by definition the point at the centre of the warp bubble moves on a geodesic and is 'massless'. That is, in Alcubierre's original formalism and in the Natario formalism the spaceship is always treated as a test particle, while in the linearized theory we can treat the spaceship as a finite mass object. For both the Alcubierre and Natario warp drives we find that even at low speeds the net (negative) energy stored in the warp fields must be a significant fraction of the mass of the spaceship

Speed regulating Effects of Incentive-based Intelligent Speed Adaptation in the short and medium term

DEFF Research Database (Denmark)

Agerholm, Niels

Speed regulating Effects of Incentive-based Intelligent Speed Adaptation in the short and medium term Despite massive improvements in vehicles’ safety equipment, more information and safer road network, inappropriate road safety is still causing that more than 250 people are killed and several...... thousands injured each year in Denmark. Until a few years ago the number of fatalities in most countries had decreased while the amount of traffic increased. However, this trend has been replaced by a more uncertain development towards a constant or even somewhat increasing risk. Inappropriate speeding...... is a central cause for the high number of fatalities on the roads. Despite speed limits, speed limit violating driving behaviour is still widespread in Denmark. Traditional solutions to prevent speed violation have been enforcement, information, and enhanced road design. It seems, however, hard to achieve...

Creating a driving profile for older adults using GPS devices and naturalistic driving methodology.

Science.gov (United States)

Babulal, Ganesh M; Traub, Cindy M; Webb, Mollie; Stout, Sarah H; Addison, Aaron; Carr, David B; Ott, Brian R; Morris, John C; Roe, Catherine M

2016-01-01

Background/Objectives : Road tests and driving simulators are most commonly used in research studies and clinical evaluations of older drivers. Our objective was to describe the process and associated challenges in adapting an existing, commercial, off-the-shelf (COTS), in-vehicle device for naturalistic, longitudinal research to better understand daily driving behavior in older drivers. Design : The Azuga G2 Tracking Device TM was installed in each participant's vehicle, and we collected data over 5 months (speed, latitude/longitude) every 30-seconds when the vehicle was driven.  Setting : The Knight Alzheimer's Disease Research Center at Washington University School of Medicine. Participants : Five individuals enrolled in a larger, longitudinal study assessing preclinical Alzheimer disease and driving performance.  Participants were aged 65+ years and had normal cognition. Measurements :  Spatial components included Primary Location(s), Driving Areas, Mean Centers and Unique Destinations.  Temporal components included number of trips taken during different times of the day.  Behavioral components included number of hard braking, speeding and sudden acceleration events. Methods :  Individual 30-second observations, each comprising one breadcrumb, and trip-level data were collected and analyzed in R and ArcGIS.  Results : Primary locations were confirmed to be 100% accurate when compared to known addresses.  Based on the locations of the breadcrumbs, we were able to successfully identify frequently visited locations and general travel patterns.  Based on the reported time from the breadcrumbs, we could assess number of trips driven in daylight vs. night.  Data on additional events while driving allowed us to compute the number of adverse driving alerts over the course of the 5-month period. Conclusions : Compared to cameras and highly instrumented vehicle in other naturalistic studies, the compact COTS device was quickly installed and transmitted high

High-speed elevators controlled by inverters

Energy Technology Data Exchange (ETDEWEB)

Sakai, Yoshio; Takahashi, Hideaki; Nakamura, Kiyoshi; Kinoshita, Hiroshi

1988-10-25

The super-high-speed elevator with superiority to 300m/min of speed, requires both the large capacity power and wide range speed controls. Therefore, in order to materialize the smooth and quiet operation characteristics, by applying the inverter control, the low torque ripple control in the low frequency range and high frequency large capacity inverting for lowering the motor in noise are necessary with their being assured of reliability. To satisfy the above necessary items, together with the development of a sine wave pulse width and frequency modulation (PWM/PFM) control system, to more precisely enable the sine wave electric current control, and 3kHz switching power converter, using a 800A power transistor module, a supervoltage control circuit under the extraordinary condition was designed. As a result of commercializing a 360m/min super-high speed inverter elevator, the power source unit, due to the effect of high power factor, could be reduced by 30% in capacity and also the higher harmonic wave including ratio could be considerably lowered to the inferiority to 5%. 2 references, 7 figures, 1 table.

Control rod drives

International Nuclear Information System (INIS)

Hayakawa, Hiroyasu.

1979-01-01

Purpose: To enable rapid control in a simple circuit by providing a motor control device having an electric capacity capable of simultaneously driving all of the control rods rapidly only in the inserting direction as well as a motor controlling device capable of fine control for the insertion and extraction at usual operation. Constitution: The control rod drives comprise a first motor control device capable of finely controlling the control rods both in inserting and extracting directions, a second motor control device capable of rapidly driving the control rods only in the inserting direction, and a first motor switching circuit and a second motor switching circuit switched by switches. Upon issue of a rapid insertion instruction for the control rods, the second motor switching circuit is closed by the switch and the second motor control circuit and driving motors are connected. Thus, each of the control rod driving motors is driven at a high speed in the inserting direction to rapidly insert all of the control rods. (Yoshino, Y.)

High - speed steel for precise cased tools

International Nuclear Information System (INIS)

Karwiarz, J.; Mazur, A.

2001-01-01

The test results of high-vanadium high - speed steel (SWV9) for precise casted tools are presented. The face -milling cutters of NFCa80A type have been tested in industrial operating conditions. An average life - time of SWV9 steel tools was 3-10 times longer compare to the conventional high - speed milling cutters. Metallography of SWB9 precise casted steel revealed beneficial for tool properties distribution of primary vanadium carbides in the steel matrix. Presented results should be a good argument for wide application of high - vanadium high - speed steel for precise casted tools. (author)

Ultra high energy cosmic rays and magnetic fields

Energy Technology Data Exchange (ETDEWEB)

Stanev, Todor; Engel, Ralph; Alvarez-Muniz, Jaime; Seckel, David

2002-07-01

We follow the propagation of ultra high energy protons in the presence of random and regular magnetic fields and discuss some of the changes in the angular and energy distributions of these particles introduced by the scattering in the magnetic fields.

Ultra high energy cosmic rays and magnetic fields

International Nuclear Information System (INIS)

Stanev, Todor; Engel, Ralph; Alvarez-Muniz, Jaime; Seckel, David

2002-01-01

We follow the propagation of ultra high energy protons in the presence of random and regular magnetic fields and discuss some of the changes in the angular and energy distributions of these particles introduced by the scattering in the magnetic fields

Asleep at the automated wheel-Sleepiness and fatigue during highly automated driving.

Science.gov (United States)

Vogelpohl, Tobias; Kühn, Matthias; Hummel, Thomas; Vollrath, Mark

2018-03-20

Due to the lack of active involvement in the driving situation and due to monotonous driving environments drivers with automation may be prone to become fatigued faster than manual drivers (e.g. Schömig et al., 2015). However, little is known about the progression of fatigue during automated driving and its effects on the ability to take back manual control after a take-over request. In this driving simulator study with Nö=ö60 drivers we used a three factorial 2ö×ö2ö×ö12 mixed design to analyze the progression (12ö×ö5ömin; within subjects) of driver fatigue in drivers with automation compared to manual drivers (between subjects). Driver fatigue was induced as either mainly sleep related or mainly task related fatigue (between subjects). Additionally, we investigated the drivers' reactions to a take-over request in a critical driving scenario to gain insights into the ability of fatigued drivers to regain manual control and situation awareness after automated driving. Drivers in the automated driving condition exhibited facial indicators of fatigue after 15 to 35ömin of driving. Manual drivers only showed similar indicators of fatigue if they suffered from a lack of sleep and then only after a longer period of driving (approx. 40ömin). Several drivers in the automated condition closed their eyes for extended periods of time. In the driving with automation condition mean automation deactivation times after a take-over request were slower for a certain percentage (about 30%) of the drivers with a lack of sleep (Mö=ö3.2; SDö=ö2.1ös) compared to the reaction times after a long drive (Mö=ö2.4; SDö=ö0.9ös). Drivers with automation also took longer than manual drivers to first glance at the speed display after a take-over request and were more likely to stay behind a braking lead vehicle instead of overtaking it. Drivers are unable to stay alert during extended periods of automated driving without non-driving related tasks. Fatigued drivers could

FPGA implementation of adaptive ANN controller for speed regulation of permanent magnet stepper motor drives

Energy Technology Data Exchange (ETDEWEB)

Hasanien, Hany M., E-mail: Hanyhasanien@ieee.or [Dept. of Elec. Power and Machines, Faculty of Eng., Ain Shams Univ., Cairo (Egypt)

2011-02-15

This paper presents a novel adaptive artificial neural network (ANN) controller, which applies on permanent magnet stepper motor (PMSM) for regulating its speed. The dynamic response of the PMSM with the proposed controller is studied during the starting process under the full load torque and under load disturbance. The effectiveness of the proposed adaptive ANN controller is then compared with that of the conventional PI controller. The proposed methodology solves the problem of nonlinearities and load changes of PMSM drives. The proposed controller ensures fast and accurate dynamic response with an excellent steady state performance. Matlab/Simulink tool is used for this dynamic simulation study. The main contribution of this work is the implementation of the proposed controller on field programmable gate array (FPGA) hardware to drive the stepper motor. The driver is built on FPGA Spartan-3E Starter from Xilinx. Experimental results are presented to demonstrate the validity and effectiveness of the proposed control scheme.

FPGA implementation of adaptive ANN controller for speed regulation of permanent magnet stepper motor drives

International Nuclear Information System (INIS)

Hasanien, Hany M.

2011-01-01

This paper presents a novel adaptive artificial neural network (ANN) controller, which applies on permanent magnet stepper motor (PMSM) for regulating its speed. The dynamic response of the PMSM with the proposed controller is studied during the starting process under the full load torque and under load disturbance. The effectiveness of the proposed adaptive ANN controller is then compared with that of the conventional PI controller. The proposed methodology solves the problem of nonlinearities and load changes of PMSM drives. The proposed controller ensures fast and accurate dynamic response with an excellent steady state performance. Matlab/Simulink tool is used for this dynamic simulation study. The main contribution of this work is the implementation of the proposed controller on field programmable gate array (FPGA) hardware to drive the stepper motor. The driver is built on FPGA Spartan-3E Starter from Xilinx. Experimental results are presented to demonstrate the validity and effectiveness of the proposed control scheme.

Specific features of high-cycle and ultra-high-cycle fatigue

Czech Academy of Sciences Publication Activity Database

Lukáš, Petr; Kunz, Ludvík

2002-01-01

Roč. 25, - (2002), s. 747-753 ISSN 8756-758X R&D Projects: GA AV ČR KSK1010104; GA AV ČR IAA2041002 Institutional research plan: CEZ:AV0Z2041904 Keywords : ultra high cycle fatigue * fatigue mechanisms * cyclic plastic deformation Subject RIV: JL - Materials Fatigue, Friction Mechanics Impact factor: 0.701, year: 2002

Effects of Lane Width, Lane Position and Edge Shoulder Width on Driving Behavior in Underground Urban Expressways: A Driving Simulator Study

Directory of Open Access Journals (Sweden)

Shuo Liu

2016-10-01

Full Text Available This study tested the effects of lane width, lane position and edge shoulder width on driving behavior for a three-lane underground urban expressway. A driving simulator was used with 24 volunteer test subjects. Five lane widths (2.85, 3.00, 3.25, 3.50, and 3.75 m and three shoulder widths (0.50, 0.75, and 1.00 m were studied. Driving speed, lane deviation and subjective perception of driving behavior were collected as performance measures. The results show that lane and shoulder width have significant effects on driving speed. Average driving speed increases from 60.01 km/h in the narrowest lane to 88.05 km/h in the widest lane. While both narrower lanes and shoulders result in reduced speed and lateral lane deviation, the effect of lane width is greater than that of shoulder width. When the lane and shoulder are narrow, drivers in the left or right lane tend to shy away from the tunnel wall, even encroaching into the neighboring middle lane. As the lane or shoulder gets wider, drivers tend to stay in the middle of the lane. An interesting finding is that although few participants acknowledged that lane position had any great bearing on their driving behaviors, the observed driving speed is statistically higher in the left lane than in the other two lanes when the lane width is narrow (in 2.85, 3 and 3.25 m lanes. These findings provided support for amending the current design specifications of urban underground roads, such as the relationship between design speed and lane width, speed limit, and combination form of lanes.

Laser beam welding of new ultra-high strength and supra-ductile steels

OpenAIRE

Dahmen, M.

2015-01-01

Ultra-high strength and supra-ductile are entering fields of new applications. Those materials are excellent candidates for modern light-weight construction and functional integration. As ultra-high strength steels the stainless martensitic grade 1.4034 and the bainitic steel UNS 53835 are investigated. For the supra-ductile steels stand two high austenitic steels with 18 and 28 % manganese. As there are no processing windows an approach from the metallurgical base on is required. Adjusting t...

Dynamic Speed Adaptation for Path Tracking Based on Curvature Information and Speed Limits.

Science.gov (United States)

Gámez Serna, Citlalli; Ruichek, Yassine

2017-06-14

A critical concern of autonomous vehicles is safety. Different approaches have tried to enhance driving safety to reduce the number of fatal crashes and severe injuries. As an example, Intelligent Speed Adaptation (ISA) systems warn the driver when the vehicle exceeds the recommended speed limit. However, these systems only take into account fixed speed limits without considering factors like road geometry. In this paper, we consider road curvature with speed limits to automatically adjust vehicle's speed with the ideal one through our proposed Dynamic Speed Adaptation (DSA) method. Furthermore, 'curve analysis extraction' and 'speed limits database creation' are also part of our contribution. An algorithm that analyzes GPS information off-line identifies high curvature segments and estimates the speed for each curve. The speed limit database contains information about the different speed limit zones for each traveled path. Our DSA senses speed limits and curves of the road using GPS information and ensures smooth speed transitions between current and ideal speeds. Through experimental simulations with different control algorithms on real and simulated datasets, we prove that our method is able to significantly reduce lateral errors on sharp curves, to respect speed limits and consequently increase safety and comfort for the passenger.

A New Class of Resonant Discharge Drive Topology for Switched Reluctance Motor

Directory of Open Access Journals (Sweden)

M. Asgar

2009-12-01

Full Text Available Switched reluctance motor (SRM drive has a remarkable characteristic, high efficiency, and good controllability, which makes it attractive for high-speed applications. In this paper, the basic control strategy for a switched reluctance motor drive circuit is explained and then three different resonant discharge topologies for SRM drive circuit are proposed. Due to resonantly discharging of excess energy, these topologies provide faster rate of fall for the phase current, which permits the motor to operate at higher speeds. In the new circuits a capacitor is charged resonantly by the use of motor phase windings during the phase turn off periods and then discharged via an inductor and a diode during the next working strokes. Three different drive circuits utilizing this process are proposed. A detailed explanation and demonstration of the converter circuits have been presented.

High-speed ground transportation development outside United States

Energy Technology Data Exchange (ETDEWEB)

Eastham, T.R. [Queen`s Univ., Kingston, Ontario (United Kingdom)

1995-09-01

This paper surveys the state of high-speed (in excess of 200 km/h) ground-transportation developments outside the United States. Both high-speed rail and Maglev systems are covered. Many vehicle systems capable of providing intercity service in the speed range 200--500 km/h are or will soon be available. The current state of various technologies, their implementation, and the near-term plans of countries that are most active in high-speed ground transportation development are reported.

Aerodynamic design on high-speed trains

Science.gov (United States)

Ding, San-San; Li, Qiang; Tian, Ai-Qin; Du, Jian; Liu, Jia-Li

2016-04-01

Compared with the traditional train, the operational speed of the high-speed train has largely improved, and the dynamic environment of the train has changed from one of mechanical domination to one of aerodynamic domination. The aerodynamic problem has become the key technological challenge of high-speed trains and significantly affects the economy, environment, safety, and comfort. In this paper, the relationships among the aerodynamic design principle, aerodynamic performance indexes, and design variables are first studied, and the research methods of train aerodynamics are proposed, including numerical simulation, a reduced-scale test, and a full-scale test. Technological schemes of train aerodynamics involve the optimization design of the streamlined head and the smooth design of the body surface. Optimization design of the streamlined head includes conception design, project design, numerical simulation, and a reduced-scale test. Smooth design of the body surface is mainly used for the key parts, such as electric-current collecting system, wheel truck compartment, and windshield. The aerodynamic design method established in this paper has been successfully applied to various high-speed trains (CRH380A, CRH380AM, CRH6, CRH2G, and the Standard electric multiple unit (EMU)) that have met expected design objectives. The research results can provide an effective guideline for the aerodynamic design of high-speed trains.

Stellar by Day, Planetary by Night: Atmospheres of Ultra-Hot Jupiters

Science.gov (United States)

Hensley, Kerry

2018-06-01

.For reasonable eastward wind speeds, Bell and Cowan found that the recombination of atomic hydrogen shifts the peak of the phase curve in the eastward direction, with the shift becoming more pronounced with increasing eastward wind speed. Additionally, because heat is distributed more evenly across the planet, including this process decreases the amplitude of the phase variations.A Bright Future for Ultra-hot JupitersTheoretical phase curves for three wind speeds. Transits and eclipses have been neglected. [Bell Cowan 2018]While this simple model doesnt include potentially important effects such as the changing atmospheric opacity as a function of longitude or formation of clouds on the planets nightside, this result indicates that caution is required when interpreting phase curves of ultra-hot Jupiters. For example, neglecting recombination means assuming a lower heat transport efficiency, which will require artifically high wind speeds to match observed phase curves.Only a few ultra-hot Jupiters are currently known, but that will soon change. The Transiting Exoplanet Survey Satellite (TESS) mission, which is set to begin its first science observations on June 17, 2018, will search for exoplanets around bright stars, including nearby cool stars and more distant hot stars. The hot stars may play host to these exotic exoplanets, and upcoming observations of ultra-hot Jupiters like KELT-9b will put this theory of heat redistribution to the test.CitationTaylor J. Bell Nicolas B. Cowan 2018 ApJL 857 L20. doi:10.3847/2041-8213/aabcc8

Functional aluminum alloys for ultra high vacuum use

International Nuclear Information System (INIS)

Kato, Yutaka; Tsukamoto, Kenji; Isoyama, Eizo

1985-01-01

Ultra high vacuum systems made of aluminum alloys are actively developed. The reasons for using aluminum alloys are low residual radioactivity, light weight, good machinability, good thermal conductivity, non-magnetism. The important function required for ultra high vacuum materials is low outgassing rate, but surface gas on ordinary aluminum is much. Then the research on aluminum surface structure with low outgassing rate has been made and the special extrusion method, that is, extrusion method with the conditions of preventing air from entering inside of pipe and of taking in mixture gas of Ar + O 2 , was developed. 6063 alloy obtained by special extrusion method showed low outgassing rate (2 x 10 -13 Torr. 1/s. cm 2 ) by only 150 deg C, 24 h baking. For the future it will be important to develop aluminum alloys with low dynamic outgassing rate as well as low static outgassing rate. (author)

Fault Tolerant and Optimal Control of Wind Turbines with Distributed High-Speed Generators

Directory of Open Access Journals (Sweden)

Urs Giger

2017-01-01

Full Text Available In this paper, the control scheme of a distributed high-speed generator system with a total amount of 12 generators and nominal generator speed of 7000 min − 1 is studied. Specifically, a fault tolerant control (FTC scheme is proposed to keep the turbine in operation in the presence of up to four simultaneous generator faults. The proposed controller structure consists of two layers: The upper layer is the baseline controller, which is separated into a partial load region with the generator torque as an actuating signal and the full-load operation region with the collective pitch angle as the other actuating signal. In addition, the lower layer is responsible for the fault diagnosis and FTC characteristics of the distributed generator drive train. The fault reconstruction and fault tolerant control strategy are tested in simulations with several actuator faults of different types.

Laser beam welding of new ultra-high strength and supra-ductile steels

Science.gov (United States)

Dahmen, Martin

2015-03-01

Ultra-high strength and supra-ductile are entering fields of new applications. Those materials are excellent candidates for modern light-weight construction and functional integration. As ultra-high strength steels the stainless martensitic grade 1.4034 and the bainitic steel UNS 53835 are investigated. For the supra-ductile steels stand two high austenitic steels with 18 and 28 % manganese. As there are no processing windows an approach from the metallurgical base on is required. Adjusting the weld microstructure the Q+P and the QT steels require weld heat treatment. The HSD steel is weldable without. Due to their applications the ultra-high strength steels are welded in as-rolled and strengthened condition. Also the reaction of the weld on hot stamping is reflected for the martensitic grades. The supra-ductile steels are welded as solution annealed and work hardened by 50%. The results show the general suitability for laser beam welding.

Comparison of drive systems for pulsed synchronous machines - an overview

International Nuclear Information System (INIS)

Baumgart, G.E.; Boenig, H.J.

1986-01-01

Magnetically confined plasma fusion experiments require large pulses of energy to be delivered into coil systems. One of the most effective methods of generating these high energy pulses is to convert stored inertial energy into electrical energy. Large synchronous generators of both the vertical and horizontal shaft type have been successfully used for this purpose. As the pulsed energy is delivered to the load, the inertial energy of the rotor of the machine is changed into electrical energy, causing the rotor to slow down. A drive system is required to accelerate the generator from standstill to the maximum operating speed and between load pulses from a reduced operating speed to the maximum speed. There are several types of drive systems that can be used for this application. An overview of six candidate drive systems is presented and comparisons of cost, performance, efficiency and line effects for these systems are described

Comparison of drive systems for pulsed synchronous machines: an overview

International Nuclear Information System (INIS)

Baumgart, G.E.; Boenig, H.J.

1985-01-01

Magnetically confined plasma fusion experiments require large pulses of energy to be delivered into coil systems. One of the most effective methods of generating these high energy pulses is to convert stored inertial energy into electrical energy. Large synchronous generators of both the vertical and horizontal shaft type have been successfully used for this purpose. As the pulsed energy is delivered to the load, the inertial energy of the rotor of the machine is changed into electrical energy, causing the rotor to slow down. A drive system is required to accelerate the generator from standstill to the maximum operating speed and between load pulses from a reduced operating speed to the maximum speed. There are several types of drive systems that can be used for this application. An overview of six candidate drive systems is presented and comparisons of cost, performance, efficiency, and line effects for these systems are described

Torque- and Speed Control of a Pitch Regulated Wind Turbine

Energy Technology Data Exchange (ETDEWEB)

Rasila, Mika

2003-07-01

Variable speed operated wind turbines has the potential to reduce fatigue loads, compared to fixed speed wind turbines. With pitch controllable rotor blades limitation of the power at high wind speeds is obtained. The thesis describes different controlling aspects concerning wind turbines and how these together can be used to optimize the system's performance. Torque control is used in order to achieve reduction on the mechanical loads on the drive-train for low wind speeds and limitation of power output for high wind speeds. In the high wind speed interval torque control is effective in order to limit the output power if a sufficiently fast pitch actuator is used. In the middle wind speed interval filter utilization can be used to give a reference signal to the controller in order to reduce speed and torque variations.

A comparison of high-speed flywheels, batteries, and ultracapacitors on the bases of cost and fuel economy as the energy storage system in a fuel cell based hybrid electric vehicle

Energy Technology Data Exchange (ETDEWEB)

Doucette, Reed T.; McCulloch, Malcolm D. [Department of Engineering Science, University of Oxford, Thom Building, Parks Road, Oxford, OX1 3PJ (United Kingdom)

2011-02-01

Fuel cells aboard hybrid electric vehicles (HEVs) are often hybridized with an energy storage system (ESS). Batteries and ultracapacitors are the most common technologies used in ESSs aboard HEVs. High-speed flywheels are an emerging technology with traits that have the potential to make them competitive with more established battery and ultracapacitor technologies in certain vehicular applications. This study compares high-speed flywheels, ultracapacitors, and batteries functioning as the ESS in a fuel cell based HEV on the bases of cost and fuel economy. In this study, computer models were built to simulate the powertrain of a fuel cell based HEV where high-speed flywheels, batteries, and ultracapacitors of a range of sizes were used as the ESS. A simulated vehicle with a powertrain using each of these technologies was run over two different drive cycles in order to see how the different ESSs performed under different driving patterns. The results showed that when cost and fuel economy were both considered, high-speed flywheels were competitive with batteries and ultracapacitors. (author)

Ultra high performance liquid chromatography of seized drugs

NARCIS (Netherlands)

Lurie, I.S.

2010-01-01

The primary goal of this thesis is to investigate the use of ultra high performance liquid chromatography (UHPLC) for the analysis of seized drugs. This goal was largely achieved and significant progress was made in achieving improved separation and detection of drugs of forensic interest.

Manganese oxide micro-supercapacitors with ultra-high areal capacitance

Science.gov (United States)

Wang, Xu; Myers, Benjamin D.; Yan, Jian; Shekhawat, Gajendra; Dravid, Vinayak; Lee, Pooi See

2013-05-01

A symmetric micro-supercapacitor is constructed by electrochemically depositing manganese oxide onto micro-patterned current collectors. High surface-to-volume ratio of manganese oxide and short diffusion distance between electrodes give an ultra-high areal capacitance of 56.3 mF cm-2 at a current density of 27.2 μA cm-2.A symmetric micro-supercapacitor is constructed by electrochemically depositing manganese oxide onto micro-patterned current collectors. High surface-to-volume ratio of manganese oxide and short diffusion distance between electrodes give an ultra-high areal capacitance of 56.3 mF cm-2 at a current density of 27.2 μA cm-2. Electronic supplementary information (ESI) available: Experimental procedures; optical images of micro-supercapacitors; areal capacitances of samples M-0.3C, M-0.6C and M-0.9C; illustration of interdigital finger electrodes; Nyquist plot of Co(OH)2 deposited on micro-electrodes. See DOI: 10.1039/c3nr00210a

Intelligent Speed Adaptation for involuntary drivers

DEFF Research Database (Denmark)

Agerholm, Niels; Tradisauskas, Nerius; Juhl, Jens

2012-01-01

and warning, the ISA had an incentive in the form of rewards for speeding avoidance and social control - the latter, however, did not work sufficiently. When a key ID was used, the proportion of speeding was low while driving with ISA. Without key ID there was virtually no change in driving behaviour...

Ultra-High-Energy Cosmic Rays

CERN Document Server

Dova, M.T.

2015-05-22

The origin of the ultra high energy cosmic rays (UHECR) with energies above E > 10 17 eV, is still unknown. The discovery of their sources will reveal the engines of the most energetic astrophysical accelerators in the universe. This is a written version of a series of lectures devoted to UHECR at the 2013 CERN-Latin-American School of High-Energy Physics. We present anintroduction to acceleration mechanisms of charged particles to the highest energies in astrophysical objects, their propagation from the sources to Earth, and the experimental techniques for their detection. We also discuss some of the relevant observational results from Telescope Array and Pierre Auger Observatory. These experiments deal with particle interactions at energies orders of magnitude higher than achieved in terrestrial accelerators.

Design of a Fatigue Detection System for High-Speed Trains Based on Driver Vigilance Using a Wireless Wearable EEG

Directory of Open Access Journals (Sweden)

Xiaoliang Zhang

2017-03-01

Full Text Available The vigilance of the driver is important for railway safety, despite not being included in the safety management system (SMS for high-speed train safety. In this paper, a novel fatigue detection system for high-speed train safety based on monitoring train driver vigilance using a wireless wearable electroencephalograph (EEG is presented. This system is designed to detect whether the driver is drowsiness. The proposed system consists of three main parts: (1 a wireless wearable EEG collection; (2 train driver vigilance detection; and (3 early warning device for train driver. In the first part, an 8-channel wireless wearable brain-computer interface (BCI device acquires the locomotive driver’s brain EEG signal comfortably under high-speed train-driving conditions. The recorded data are transmitted to a personal computer (PC via Bluetooth. In the second step, a support vector machine (SVM classification algorithm is implemented to determine the vigilance level using the Fast Fourier transform (FFT to extract the EEG power spectrum density (PSD. In addition, an early warning device begins to work if fatigue is detected. The simulation and test results demonstrate the feasibility of the proposed fatigue detection system for high-speed train safety.

Influence of roadside infrastructure on driving behavior: driving simulator study

NARCIS (Netherlands)