WorldWideScience

Sample records for ultimately define optimum

  1. Optimum Criteria for Developing Defined Structures

    Directory of Open Access Journals (Sweden)

    Ion IVAN

    2008-01-01

    Full Text Available Basic aspects concerning distributed applications are presented: definition, particularities and importance. For distributed applications linear, arborescent, graph structures are defined with different versions and aggregation methods. Distributed applications have associated structures which through their characteristics influence the costs of the stages in the development cycle and the exploitation costs transferred to each user. The complexity of the defined structures is analyzed. The minimum and maximum criteria are enumerated for optimizing distributed application structures.

  2. Defining poor and optimum performance in an IVF programme.

    Science.gov (United States)

    Castilla, Jose A; Hernandez, Juana; Cabello, Yolanda; Lafuente, Alejandro; Pajuelo, Nuria; Marqueta, Javier; Coroleu, Buenaventura

    2008-01-01

    At present there is considerable interest in healthcare administration, among professionals and among the general public concerning the quality of programmes of assisted reproduction. There exist various methods for comparing and analysing the results of clinical activity, with graphical methods being the most commonly used for this purpose. As yet, there is no general consensus as to how the poor performance (PP) or optimum performance (OP) of assisted reproductive technologies should be defined. Data from the IVF/ICSI register of the Spanish Fertility Society were used to compare and analyse different definitions of PP or OP. The primary variable best reflecting the quality of an IVF/ICSI programme was taken to be the percentage of singleton births per IVF/ICSI cycle initiated. Of the 75 infertility clinics that took part in the SEF-2003 survey, data on births were provided by 58. A total of 25 462 cycles were analysed. The following graphical classification methods were used: ranking of the proportion of singleton births per cycles started in each centre (league table), Shewhart control charts, funnel plots, best and worst-case scenarios and state of the art methods. The clinics classified as producing PP or OP varied considerably depending on the classification method used. Only three were rated as providing 'PP' or 'OP' by all methods, unanimously. Another four clinics were classified as 'poor' or 'optimum' by all the methods except one. On interpreting the results derived from IVF/ICSI centres, it is essential to take into account the characteristics of the method used for this purpose.

  3. Different Ultimate Factors Define Timing of Breeding in Two Related Species.

    Directory of Open Access Journals (Sweden)

    Veli-Matti Pakanen

    Full Text Available Correct reproductive timing is crucial for fitness. Breeding phenology even in similar species can differ due to different selective pressures on the timing of reproduction. These selection pressures define species' responses to warming springs. The temporal match-mismatch hypothesis suggests that timing of breeding in animals is selected to match with food availability (synchrony. Alternatively, time-dependent breeding success (the date hypothesis can result from other seasonally deteriorating ecological conditions such as intra- or interspecific competition or predation. We studied the effects of two ultimate factors on the timing of breeding, synchrony and other time-dependent factors (time-dependence, in sympatric populations of two related forest-dwelling passerine species, the great tit (Parus major and the willow tit (Poecile montanus by modelling recruitment with long-term capture-recapture data. We hypothesized that these two factors have different relevance for fitness in these species. We found that local recruitment in both species showed quadratic relationships with both time-dependence and synchrony. However, the importance of these factors was markedly different between the studied species. Caterpillar food played a predominant role in predicting the timing of breeding of the great tit. In contrast, for the willow tit time-dependence modelled as timing in relation to conspecifics was more important for local recruitment than synchrony. High caterpillar biomass experienced during the pre- and post-fledging periods increased local recruitment of both species. These contrasting results confirm that these species experience different selective pressures upon the timing of breeding, and hence responses to climate change may differ. Detailed information about life-history strategies is required to understand the effects of climate change, even in closely related taxa. The temporal match-mismatch hypothesis should be extended to consider

  4. Do preliminary chest X-ray findings define the optimum role of pulmonary scintigraphy in suspected pulmonary embolism?

    International Nuclear Information System (INIS)

    Forbes, Kirsten P.N.; Reid, John H.; Murchison, John T.

    2001-01-01

    AIM: To investigate if preliminary chest radiograph (CXR) findings can define the optimum role of lung scintigraphy in subjects investigated for pulmonary embolism (PE). MATERIALS AND METHODS: The CXR and scintigraphy findings from 613 consecutive subjects investigated for suspected PE were retrieved from a radiological database. Of 393 patients with abnormal CXRs, a subgroup of 238 was examined and individual radiographic abnormalities were characterized. CXR findings were related to the scintigraphy result. RESULTS: Scintigraphy was normal in 286 subjects (47%), non-diagnostic in 207 (34%) and high probability for PE in 120 (20%). In 393 subjects (64%) the preliminary CXR was abnormal and 188 (48%) of scintigrams in this group were non-diagnostic. Individual radiographic abnormalities were not associated with significantly different scintigraphic outcomes. If the preliminary CXR was normal (36%), the proportion of non-diagnostic scintigrams decreased to 9% (19 of 220 subjects) (P < 0.05). CONCLUSION: In subjects investigated for PE, an abnormal CXR increases the prevalence of non-diagnostic scintigrams. A normal pre-test CXR is more often associated with a definitive (normal or high probability) scintigram result. The chest radiograph may be useful in deciding the optimum sequence of investigations. Forbes, K.P.N., Reid, J.H., Murchison, J.T. (2001)

  5. The Ultimate Big Data Enterprise Initiative: Defining Functional Capabilities for an International Information System (IIS) for Orbital Space Data (OSD)

    Science.gov (United States)

    Raygan, R.

    Global collaboration in support of an International Information System (IIS) for Orbital Space Data (OSD) literally requires a global enterprise. As with many information technology enterprise initiatives attempting to coral the desires of business with the budgets and limitations of technology, Space Situational Awareness (SSA) includes many of the same challenges: 1) Adaptive / Intuitive Dash Board that facilitates User Experience Design for a variety of users. 2) Asset Management of hundreds of thousands of objects moving at thousands of miles per hour hundreds of miles in space. 3) Normalization and integration of diverse data in various languages, possibly hidden or protected from easy access. 4) Expectations of near real-time information availability coupled with predictive analysis to affect decisions before critical points of no return, such as Space Object Conjunction Assessment (CA). 5) Data Ownership, management, taxonomy, and accuracy. 6) Integrated metrics and easily modified algorithms for "what if" analysis. This paper proposes an approach to define the functional capabilities for an IIS for OSD. These functional capabilities not only address previously identified gaps in current systems but incorporate lessons learned from other big data, enterprise, and agile information technology initiatives that correlate to the space domain. Viewing the IIS as the "data service provider" allows adoption of existing information technology processes which strengthen governance and ensure service consumers certain levels of service dependability and accuracy.

  6. Defining an optimum pumping-time requirement for sampling ground-water wells on the Hanford site

    International Nuclear Information System (INIS)

    Scharnhorst, N.L.

    1982-04-01

    The objective was to determine the optimum time period necessary to pump water from a well before a representative sample of the ground water can be obtained. It was assumed that a representative sample has been collected if the concentration of chemical parameters is the same in a number of samples taken consecutively, so that the concentration of parameters does not vary with time of collection. Ground-water samples used in this project were obtained by pumping selected wells on the Hanford Site. At each well, samples were taken at two minute intervals, and on each sample various chemical analyses were performed. Samples were checked for pH, sulfate, iron, specific conductivity, chloride, nitrate and alkalinity. The data showed that pH, alkalinity, sulfate and specific conductivity levels stabilized almost immediately after pumping of the well began. In many wells, the chloride and nitrate levels were unstable throughout the 38-minute sampling period. Iron levels, however, did not behave in either fashion. The concentration of iron in the samples was high when pumping began but dropped rapidly as pumping continued. The best explanation for this is that iron is flushed from the sides of the casing into the well when pumping begins. After several minutes of pumping, most of the dissolved iron is washed from the well casing and the iron concentration reaches a stable plateau representative of the iron concentration in the ground water.Since iron concentration takes longest to stabilize, the optimum pumping time for a well is based on the iron stabilization time for that well

  7. An analytical method for defining the pump`s power optimum of a water-to-water heat pump heating system using COP

    Directory of Open Access Journals (Sweden)

    Nyers Jozsef

    2017-01-01

    Full Text Available This paper analyzes the energy efficiency of the heat pump and the complete heat pump heating system. Essentially, the maximum of the coefficient of performance of the heat pump and the heat pump heating system are investigated and determined by applying a new analytical optimization procedure. The analyzed physical system consists of the water-to-water heat pump, circulation and well pump. In the analytical optimization procedure the "first derivative equal to zero" mathematical method is applied. The objective function is the coefficient of performance of the heat pump, and the heat pump heating system. By using the analytical optimization procedure and the objective function, as the result, the local and the total energy optimum conditions with respect to the mass flow rate of hot and cold water i. e. the power of circulation or well pump are defined.

  8. OPTIMUM PROSESSENTRERING

    Directory of Open Access Journals (Sweden)

    K. Adendorff

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: The paper derives an expression for optimum process centreing for a given design specification and spoilage and/or rework costs.

    AFRIKAANSE OPSOMMING: Die problem Van prosessentrering vir n gegewe ontwerpspesifikasie en herwerk- en/of skrootkoste word behandel.

  9. Important improvement of utilization the available geological reserves of the South mining district deposit in Majdanpek in the new defined optimum contour of the open pit using the Whittle and Gemcom softwares

    OpenAIRE

    Kržanović, Daniel; Žikić, Miodrag; Pantović, Radoje

    2012-01-01

    A significant increase in copper prices on the World Metal Exchange, whose lower limit in the long term will not be under $ 6,000 per ton of cathode copper, and reduction the operating costs of ore mining by introduction the high capacity mining equipment in the production process, requires a new consideration of the open pit South Mining District Majdanpek and defining the new final (optimum) limit of mining for the given techno economic parameters. Using the modern software tools for strate...

  10. Flux scaling: Ultimate regime

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. Flux scaling: Ultimate regime. With the Nusselt number and the mixing length scales, we get the Nusselt number and Reynolds number (w'd/ν) scalings: and or. and. scaling expected to occur at extremely high Ra Rayleigh-Benard convection. Get the ultimate regime ...

  11. Stalking the ultimate particle

    CERN Multimedia

    2003-01-01

    If you missed the ARTE programme entitled "L'Ultime Particule" broadcast in February, you have another chance to catch it in CERN's Main Auditorium on 13 March. "L'Ultime Particule" is a documentary by the French director Michel Andrieu that seeks to explain particle physics through a contemplative quest for the research physicists of matter of today and yesteryear. Invariably kitted out in a red parka and a soft hat, the programme's investigator scours the planet and the archives in search of the research physicists who are stalking the ultimate particle, the Higgs boson, in their quest to understand the structure of matter. Naturally enough, CERN is an important stage of his journey where Michel Andrieu and his team spent several days last year. Both from the physics and metaphysical points of view, "L'Ultime Particule" is worth seeing. The film's director, Michel Andrieu, will introduce his documentary and answer questions from the audience after the documentary has been shown. L'Ultime Particule by Mic...

  12. The ultimate quotable Einstein

    CERN Document Server

    2011-01-01

    Here is the definitive new edition of the hugely popular collection of Einstein quotations that has sold tens of thousands of copies worldwide and been translated into twenty-five languages. The Ultimate Quotable Einstein features 400 additional quotes, bringing the total to roughly 1,600 in all. This ultimate edition includes new sections--"On and to Children," "On Race and Prejudice," and "Einstein's Verses: A Small Selection"--as well as a chronology of Einstein's life and accomplishments, Freeman Dyson's authoritative foreword, and new commentary by Alice Calaprice.

  13. The Ultimate Technology

    DEFF Research Database (Denmark)

    Riis, Søren

    2013-01-01

    One of the most influential philosophers of the 20th century, Martin Heidegger (1889-1976), died prior to the remarkable cloning of the sheep Dolly and before Dr. Venter started his experiments on creating synthetic life, and he never explicitly discussed living technologies. However, by reinterp......One of the most influential philosophers of the 20th century, Martin Heidegger (1889-1976), died prior to the remarkable cloning of the sheep Dolly and before Dr. Venter started his experiments on creating synthetic life, and he never explicitly discussed living technologies. However......, by reinterpreting his notion of "modern technology," this article shows how it is possible to philosophically assess living technologies and to recognize ways in which Heidegger anticipated this phenomenon with his notion of cybernetics. The interpretation elucidates the fundamental process of technology becoming...... living and simultaneously presents living technology as the ultimate technology. The thesis of this article is that living technology is not just one more technology; rather, it is the perfection of technology as understood by Aristotle. Aristotle's thinking is in this way a key example of a profound...

  14. Nondissipative optimum charge regulator

    Science.gov (United States)

    Rosen, R.; Vitebsky, J. N.

    1970-01-01

    Optimum charge regulator provides constant level charge/discharge control of storage batteries. Basic power transfer and control is performed by solar panel coupled to battery through power switching circuit. Optimum controller senses battery current and modifies duty cycle of switching circuit to maximize current available to battery.

  15. Shear wall ultimate drift limits

    International Nuclear Information System (INIS)

    Duffey, T.A.; Goldman, A.; Farrar, C.R.

    1994-04-01

    Drift limits for reinforced-concrete shear walls are investigated by reviewing the open literature for appropriate experimental data. Drift values at ultimate are determined for walls with aspect ratios ranging up to a maximum of 3.53 and undergoing different types of lateral loading (cyclic static, monotonic static, and dynamic). Based on the geometry of actual nuclear power plant structures exclusive of containments and concerns regarding their response during seismic (i.e.,cyclic) loading, data are obtained from pertinent references for which the wall aspect ratio is less than or equal to approximately 1, and for which testing is cyclic in nature (typically displacement controlled). In particular, lateral deflections at ultimate load, and at points in the softening region beyond ultimate for which the load has dropped to 90, 80, 70, 60, and 50 percent of its ultimate value, are obtained and converted to drift information. The statistical nature of the data is also investigated. These data are shown to be lognormally distributed, and an analysis of variance is performed. The use of statistics to estimate Probability of Failure for a shear wall structure is illustrated

  16. Ultimate disposal of radioactive wastes

    International Nuclear Information System (INIS)

    Roethemeyer, H.

    1991-01-01

    The activities developed by the Federal Institution of Physical Engineering PTB and by the Federal Office for Radiation Protection (BfS) concentrated, among others, on work to implement ultimate storage facilities for radioactive wastes. The book illuminates this development from site designation to the preliminary evaluation of the Gorleben salt dome, to the preparation of planning documents proving that the Konrad ore mine is suitable for a repository. The paper shows the legal provisions involved; research and development tasks; collection of radioactive wastes ready for ultimate disposal; safety analysis in the commissioning and post-operational stages, and product control. The historical development of waste management in the Federal Republic of Germany and international cooperation in this area are outlined. (DG) [de

  17. Ultimate fate of constrained voters

    International Nuclear Information System (INIS)

    Vazquez, F; Redner, S

    2004-01-01

    We examine the ultimate fate of individual opinions in a socially interacting population of leftists, centrists and rightists. In an elemental interaction between agents, a centrist and a leftist can both become centrists or both become leftists with equal rates (and similarly for a centrist and a rightist). However leftists and rightists do not interact. This interaction step between pairs of agents is applied repeatedly until the system can no longer evolve. In the mean-field limit, we determine the exact probability that the system reaches consensus (either leftist, rightist or centrist) or a frozen mixture of leftists and rightists as a function of the initial composition of the population. We also determine the mean time until the final state is reached. Some implications of our results for the ultimate fate in a limit of the Axelrod model are discussed

  18. Ultimate fate of constrained voters

    Energy Technology Data Exchange (ETDEWEB)

    Vazquez, F [Department of Physics, Center for BioDynamics, Boston University, Boston, MA 02215 (United States); Redner, S [Department of Physics, Center for Polymer Studies, Boston University, Boston, MA 02215 (United States)

    2004-09-03

    We examine the ultimate fate of individual opinions in a socially interacting population of leftists, centrists and rightists. In an elemental interaction between agents, a centrist and a leftist can both become centrists or both become leftists with equal rates (and similarly for a centrist and a rightist). However leftists and rightists do not interact. This interaction step between pairs of agents is applied repeatedly until the system can no longer evolve. In the mean-field limit, we determine the exact probability that the system reaches consensus (either leftist, rightist or centrist) or a frozen mixture of leftists and rightists as a function of the initial composition of the population. We also determine the mean time until the final state is reached. Some implications of our results for the ultimate fate in a limit of the Axelrod model are discussed.

  19. On Optimum Stratification

    OpenAIRE

    M. G. M. Khan; V. D. Prasad; D. K. Rao

    2014-01-01

    In this manuscript, we discuss the problem of determining the optimum stratification of a study (or main) variable based on the auxiliary variable that follows a uniform distribution. If the stratification of survey variable is made using the auxiliary variable it may lead to substantial gains in precision of the estimates. This problem is formulated as a Nonlinear Programming Problem (NLPP), which turn out to multistage decision problem and is solved using dynamic programming technique.

  20. Experimental investigation of ultimate loads

    Energy Technology Data Exchange (ETDEWEB)

    Petersen, S M; Larsen, G C; Antoniou, I; Lind, S O; Courtney, M [Risoe National Lab., Wind Energy and Atmospheric Physics, Roskilde (Denmark)

    1999-03-01

    Verification of the structural integrity of a wind turbine involves analysis of fatigue loading as well as ultimate loading. With the trend of persistently growing turbines, the ultimate loading seems to become relatively more important. For wind turbines designed according to the wind conditions prescribed in the IEC-61400 code, the ultimate load is often identified as the leading load parameter. Exemplified by the use of an extensive measurement campaign a procedure for evaluation of the extreme flap-wise bending moments, occurring during normal operating of a wind turbine, is presented. The structural measurements are made on a NEG Micon 650 kW wind turbine erected at a complex high wind site in Oak Creek, California. The turbine is located on the top of a ridge. The prevailing wind direction is perpendicular to the ridge, and the annual mean wind speed is 9.5 m/s. The associated wind field measurement, are taken from two instrumented masts erected less than one rotor diameter in front of the turbine in direction of the prevailing wind direction. Both masts are instrumented at different heights in order to gain insight of the 3D-wind speed structure over the entire rotor plane. Extreme distributions, associated with a recurrence period of 10 minutes, conditioned on the mean wind speed and the turbulence intensity are derived. Combined with the wind climate model proposed in the IEC standard, these distributions are used to predict extreme distributions with recurrence periods equal to one and fifty years, respectively. The synthesis of the conditioned PDF`s and the wind climate model is performed by means of Monte Carlo simulation. (au)

  1. Ultimate Explanations of the Universe

    CERN Document Server

    Heller, Michael

    2009-01-01

    We humans are collectively driven by a powerful - yet not fully explained - instinct to understand. We would like to see everything established, proven, laid bare. The more important an issue, the more we desire to see it clarified, stripped of all secrets, all shades of gray. What could be more important than to understand the Universe and ourselves as a part of it? To find a window onto our origin and our destiny? This book examines how far our modern cosmological theories - with their sometimes audacious models, such as inflation, cyclic histories, quantum creation, parallel universes - can take us towards answering these questions. Can such theories lead us to ultimate truths, leaving nothing unexplained? Last, but not least, Heller addresses the thorny problem of why and whether we should expect to find theories with all-encompassing explicative power.

  2. Ultimate loading of wind turbines

    DEFF Research Database (Denmark)

    Larsen, Gunner Chr.; Ronold, K.; Ejsing Jørgensen, Hans

    1999-01-01

    An extreme loading study has been conducted comprising a general wind climate analysis as well as a wind turbine reliability study. In the wind climate analysis, the distribution of the (horizontal) turbulence standard deviation, conditioned on the meanwind speed, has been approximated by fitting......, a design turbulence intensity for off-shore application is proposed which, in the IEC code framework, is applicable for extreme as well as for fatigue loaddetermination. In order to establish a rational method to analyse wind turbine components with respect to failure in ultimate loading, and in addition...... a three parameter Weibull distribution to the measured on-shore and off-shore data for wind speed variations. Specific recommendations on off-shore design turbulence intensities are lacking in the presentIEC-code. Based on the present analysis of the off-shore wind climate on two shallow water sites...

  3. The optimum spanning catenary cable

    Science.gov (United States)

    Wang, C. Y.

    2015-03-01

    A heavy cable spans two points in space. There exists an optimum cable length such that the maximum tension is minimized. If the two end points are at the same level, the optimum length is 1.258 times the distance between the ends. The optimum lengths for end points of different heights are also found.

  4. Choosing the optimum burnup

    International Nuclear Information System (INIS)

    Geller, L.; Goldstein, L.; Franks, W.A.

    1986-01-01

    This paper reviews some of the considerations utilities must evaluate when going to higher discharge burnups. The advantages and disadvantages of higher discharge burnups are described, as well as a consistent approach for evaluating optimum discharge burnup and its comparison to current practice. When an analysis is performed over the life of the plant, the design of the terminal cycles has significant impact on the lifetime savings from higher burnups. Designs for high burnup cycles have a greater average inventory value in the core. As one goes to higher burnup, there is a greater likelihood of discarding a larger value in unused fuel unless the terminal cycles are designed carefully. This effect can be large enough in some cases to wipe out the lifetime cost savings relative to operating with a higher discharge burnup cycle

  5. Assessment and characterization of radioactive waste for ultimate storage

    International Nuclear Information System (INIS)

    Brennecke, P.; Warnecke, E.

    1986-01-01

    The waste specifications determined from site safety analyses define the requirements to be met by waste forms for ultimate storage. Product quality control is the process step ensuring compliance with the conditions to be met for ultimate storage. For this purpose, radionuclide inventory, fixation method, container type, waste form and quantity, and type of waste are the most significant items on the checking list. (DG) [de

  6. Ultimate explanations and suboptimal choice.

    Science.gov (United States)

    Vasconcelos, Marco; Machado, Armando; Pandeirada, Josefa N S

    2018-07-01

    Researchers have unraveled multiple cases in which behavior deviates from rationality principles. We propose that such deviations are valuable tools to understand the adaptive significance of the underpinning mechanisms. To illustrate, we discuss in detail an experimental protocol in which animals systematically incur substantial foraging losses by preferring a lean but informative option over a rich but non-informative one. To understand how adaptive mechanisms may fail to maximize food intake, we review a model inspired by optimal foraging principles that reconciles sub-optimal choice with the view that current behavioral mechanisms were pruned by the optimizing action of natural selection. To move beyond retrospective speculation, we then review critical tests of the model, regarding both its assumptions and its (sometimes counterintuitive) predictions, all of which have been upheld. The overall contention is that (a) known mechanisms can be used to develop better ultimate accounts and that (b) to understand why mechanisms that generate suboptimal behavior evolved, we need to consider their adaptive value in the animal's characteristic ecology. Copyright © 2018 Elsevier B.V. All rights reserved.

  7. Optimum study designs.

    Science.gov (United States)

    Gu, C; Rao, D C

    2001-01-01

    Because simplistic designs will lead to prohibitively large sample sizes, the optimization of genetic study designs is critical for successfully mapping genes for complex diseases. Creative designs are necessary for detecting and amplifying the usually weak signals for complex traits. Two important outcomes of a study design--power and resolution--are implicitly tied together by the principle of uncertainty. Overemphasis on either one may lead to suboptimal designs. To achieve optimality for a particular study, therefore, practical measures such as cost-effectiveness must be used to strike a balance between power and resolution. In this light, the myriad of factors involved in study design can be checked for their effects on the ultimate outcomes, and the popular existing designs can be sorted into building blocks that may be useful for particular situations. It is hoped that imaginative construction of novel designs using such building blocks will lead to enhanced efficiency in finding genes for complex human traits.

  8. Optimum body size of Holstein replacement heifers.

    Science.gov (United States)

    Hoffman, P C

    1997-03-01

    Criteria that define optimum body size of replacement heifers are required by commercial dairy producers to evaluate replacement heifer management programs. Historically recommended body size criteria have been based on live BW measurements. Numerous research studies have observed a positive relationship between BW at first calving and first lactation milk yield, which has served as the impetus for using live BW to define body size of replacement heifers. Live BW is, however, not the only available measurement to define body size. Skeletal measurements such as wither height, length, and pelvic area have been demonstrated to be related to first lactation performance and (or) dystocia. Live BW measurements also do not define differences in body composition. Differences in body composition of replacement heifers at first calving are also related to key performance variables. An updated research data base is available for the modern Holstein genotype to incorporate measures of skeletal growth and body composition with BW when defining body size. These research projects also lend insight into the relative importance of measurements that define body size of replacement heifers. Incorporation of these measurements from current research into present BW recommendations should aid commercial dairy producers to better define replacement heifer growth and management practices. This article proposes enhancements in defining optimum body size and growth characteristics of Holstein replacement heifers.

  9. Optimum burnup of BAEC TRIGA research reactor

    International Nuclear Information System (INIS)

    Lyric, Zoairia Idris; Mahmood, Mohammad Sayem; Motalab, Mohammad Abdul; Khan, Jahirul Haque

    2013-01-01

    Highlights: ► Optimum loading scheme for BAEC TRIGA core is out-to-in loading with 10 fuels/cycle starting with 5 for the first reload. ► The discharge burnup ranges from 17% to 24% of U235 per fuel element for full power (3 MW) operation. ► Optimum extension of operating core life is 100 MWD per reload cycle. - Abstract: The TRIGA Mark II research reactor of BAEC (Bangladesh Atomic Energy Commission) has been operating since 1986 without any reshuffling or reloading yet. Optimum fuel burnup strategy has been investigated for the present BAEC TRIGA core, where three out-to-in loading schemes have been inspected in terms of core life extension, burnup economy and safety. In considering different schemes of fuel loading, optimization has been searched by only varying the number of fuels discharged and loaded. A cost function has been defined and evaluated based on the calculated core life and fuel load and discharge. The optimum loading scheme has been identified for the TRIGA core, the outside-to-inside fuel loading with ten fuels for each cycle starting with five fuels for the first reload. The discharge burnup has been found ranging from 17% to 24% of U235 per fuel element and optimum extension of core operating life is 100 MWD for each loading cycle. This study will contribute to the in-core fuel management of TRIGA reactor

  10. Problem of determining optimum geological and technical measures

    Energy Technology Data Exchange (ETDEWEB)

    Osipov, G N; Roste, Z A; Salimzhanov, E S

    1968-01-01

    This article is concerned with the mathematical simulation of oilfield operation, particularly the use of linear programing to determine optimum conditions for exploitation of a field. The basic approach is to define the field operation by a series of equations, apply boundary conditions and through an iterative computer technique find optimum operating conditions. Application of the method to Tuimazy field is illustrated.

  11. Probabilistic studies for safety at optimum cost

    International Nuclear Information System (INIS)

    Pitner, P.

    1999-01-01

    By definition, the risk of failure of very reliable components is difficult to evaluate. How can the best strategies for in service inspection and maintenance be defined to limit this risk to an acceptable level at optimum cost? It is not sufficient to design structures with margins, it is also essential to understand how they age. The probabilistic approach has made it possible to develop well proven concepts. (author)

  12. Electromagnetic radiation optimum neutralizer

    International Nuclear Information System (INIS)

    Smirnov, Igor

    2002-01-01

    This particular article relates to subtle electrical effects, and provides some evidence of a fundamental nature on how subtle low frequency electromagnetic fields might be utilized to protect human body against harmful effects of high frequencies electromagnetic radiation. I have focused my efforts on definite polar polymer compound named EMRON which is patented in the USA. This polar polymer compound can be excited by external high frequencies electromagnetic fields to generate subtle low frequency oscillations that are beneficial for cellular life structures. This concept is based on the possibility of existence of resonance phenomenon between polar polymers and biopolymers such as proteins, nucleic acids, lipids, etc. Low frequency patterns generated by defined polar polymer compound can interact with biostructures and transmit the signals that support and improve cellular functions in the body. The mechanism of this process was confirmed by number of studies. The animal (including human) brain is affected by electromagnetic waves to the extent that production of Alpha or Theta waves can be directly induced into brain by carrying an ELF (extremely low frequency, 5-12 Hz) signal on a microwave carrier frequency. EMRON does not reduce the power of electromagnetic fields. It 'shields' the cellular structures of the body against the harmful effects of EMR. The radiation is still entering the body but the neutralizing effect of EMRON renders the radiation harmless

  13. The dream of an ultimate theory

    International Nuclear Information System (INIS)

    Weinberg, S.

    1997-10-01

    Steven Weinberg describes how the dream of an ultimate theory began when one tried to unify the fundamental laws governing the stars constellations as elementary particles: electromagnetism, weak-electro theory then standard model which gives only one quantity out of its fields, the gravitation. He tries to explain to what an ultimate theory could look like. but the dream of an ultimate theory is not yet realized, there are some elementary particles to find before and then to build superconducting super colliders. The europe made it. the dream of an ultimate theory became an european dream. (N.C.)

  14. Ultimate pressure capacity of CANDU 6 containment structures

    International Nuclear Information System (INIS)

    Radulescu, J.P.; Pradolin, L.; Mamet, J.C.

    1997-01-01

    This paper summarizes the analytical work carried out and the results obtained when determining the ultimate pressure capacity (UPC) of the containment structures of CANDU 6 nuclear power plants. The purpose of the analysis work was to demonstrate that such containment structures are capable of meeting design requirements under the most severe accident conditions. For this concrete vessel subjected to internal pressure, the UPC was defined as the pressure causing through cracking in the concrete. The present paper deals with the overall behaviour of the containment. The presence of openings, penetrations and the ultimate pressure of the airlocks were considered separately. (author)

  15. Optimum Design of Plasma Focus

    International Nuclear Information System (INIS)

    Ramos, Ruben; Gonzalez, Jose; Clausse, Alejandro

    2000-01-01

    The optimum design of Plasma Focus devices is presented based in a lumped parameter model of the MHD equations.Maps in the design parameters space are obtained, which determine the length and deuterium pressure required to produce a given neutron yield.Sensitivity analyses of the main effective numbers (sweeping efficiencies) was performed, and lately the optimum values were determined in order to set a basis for the conceptual design

  16. Concussion Prevalence in Competitive Ultimate Frisbee Players

    Science.gov (United States)

    Lazar, Damien J.; Lichtenstein, Jonathan D.; Tybor, David J.

    2018-01-01

    Background: Ultimate Frisbee (ultimate) is a fast-growing, popular sport played nationally by over 4 million athletes. While several studies have examined injury rates in ultimate, no work has investigated the prevalence of concussions specifically or players’ knowledge and management of those injuries. Purpose: To estimate the lifetime prevalence of concussions in ultimate and to assess players’ knowledge of concussions as well as their concussion management behaviors. Study Design: Descriptive epidemiology study. Methods: From June to November 2015, we collected ultimate-related concussion data via an anonymous web-based survey, the Concussion in Ultimate Frisbee Survey, from a convenience sample of 787 male and female ultimate players across the United States. Results: There were 553 male and 234 female respondents included in the analysis; 26.58% of men and 24.79% of women reported that they had sustained at least 1 concussion while playing ultimate, with 45.58% and 43.10% of those men and women, respectively, reporting multiple concussions. A total of 67.81% of men and 78.21% of women stated that they would remove themselves from play after sustaining a given concussion, although 45.99% of men and 37.62% of women indicated that they had returned to play in the same game or practice. Conclusion: Our preliminary data suggest that concussions do commonly occur in competitive ultimate and that better education and management of concussions in ultimate athletes are needed. This study is an important first step in deepening our understanding of these issues. PMID:29552572

  17. THE ULTIMATE STATE CONCEPT APPLIED TO TUNNEL SUPPORT

    Directory of Open Access Journals (Sweden)

    Mladen Hudec

    2000-12-01

    Full Text Available The most questionable are the values of pressures between rock and support resulting from common deformations on the contact area between rock and support. Therefore the modelling and design of the tunnel support is not reliable, if it is based on active rock pressure resulting from this common deformations. The inversion of the design procedure is proposed. Instead of the active extreme pressure of the rock on support, the influence of ultimate reaction of the support on the rock has to be analysed. This procedure can be performed using the ultimate load principle, as proposed by Eurocodc 7 (Geotechnies. Normally, the rock has the tendency to increase the common conver¬gence until the support reaches its ultimate state. So, loading of profile boundary with the ultimate possible reaction of the support is very plausible. The reactive support pressures have to be probable and itself in equilibrium. The ultimate reactive load has to be reduced by Euro-code safety factor for structural elements and applied on the rock with given properties, or alternatively (as proposed by Eurocode 7 the soil or rock properties have to be diminished and calculated with full ultimate support pressures. If the rock with given (or proposed pro¬perties and loaded with ultimate reactive pressures resulting from supposed support, satisfy its failure criterion, then is the compound system support-rock verificatcd. By this procedure, the number of relevant material properties is reduce to the primary stress ratio and the constants defining the failure criterion. The verification can be performed by any of numerical methods, but we prefer here used boundary elements method (the paper is published in Croatian.

  18. Thermal Comfort and Optimum Humidity Part 1

    Directory of Open Access Journals (Sweden)

    M. V. Jokl

    2002-01-01

    Full Text Available The hydrothermal microclimate is the main component in indoor comfort. The optimum hydrothermal level can be ensured by suitable changes in the sources of heat and water vapor within the building, changes in the environment (the interior of the building and in the people exposed to the conditions inside the building. A change in the heat source and the source of water vapor involves improving the heat - insulating properties and the air permeability of the peripheral walls and especially of the windows. The change in the environment will bring human bodies into balance with the environment. This can be expressed in terms of an optimum or at least an acceptable globe temperature, an adequate proportion of radiant heat within the total amount of heat from the environment (defined by the difference between air and wall temperature, uniform cooling of the human body by the environment, defined a by the acceptable temperature difference between head and ankles, b by acceptable temperature variations during a shift (location unchanged, or during movement from one location to another without a change of clothing. Finally, a moisture balance between man and the environment is necessary (defined by acceptable relative air humidity. A change for human beings means a change of clothes which, of course, is limited by social acceptance in summer and by inconvenient heaviness in winter. The principles of optimum heating and cooling, humidification and dehumidification are presented in this paper.Hydrothermal comfort in an environment depends on heat and humidity flows (heat and water vapors, occurring in a given space in a building interior and affecting the total state of the human organism.

  19. Thermal Comfort and Optimum Humidity Part 2

    Directory of Open Access Journals (Sweden)

    M. V. Jokl

    2002-01-01

    Full Text Available The hydrothermal microclimate is the main component in indoor comfort. The optimum hydrothermal level can be ensured by suitable changes in the sources of heat and water vapor within the building, changes in the environment (the interior of the building and in the people exposed to the conditions inside the building. A change in the heat source and the source of water vapor involves improving the heat - insulating properties and the air permeability of the peripheral walls and especially of the windows. The change in the environment will bring human bodies into balance with the environment. This can be expressed in terms of an optimum or at least an acceptable globe temperature, an adequate proportion of radiant heat within the total amount of heat from the environment (defined by the difference between air and wall temperature, uniform cooling of the human body by the environment, defined a by the acceptable temperature difference between head and ankles, b by acceptable temperature variations during a shift (location unchanged, or during movement from one location to another without a change of clothing. Finally, a moisture balance between man and the environment is necessary (defined by acceptable relative air humidity. A change for human beings means a change of clothes which, of course, is limited by social acceptance in summer and by inconvenient heaviness in winter. The principles of optimum heating and cooling, humidification and dehumidification are presented in this paper.Hydrothermal comfort in an environment depends on heat and humidity flows (heat and water vapors, occurring in a given space in a building interior and affecting the total state of the human organism.

  20. Physical demands in competitive ultimate frisbee

    DEFF Research Database (Denmark)

    Krustrup, Peter; Mohr, Magni

    2015-01-01

    The objective was to study game demands in competitive ultimate Frisbee by performing match analysis during a game. Thirteen moderately trained (Yo-Yo intermittent recovery test levels 1 and 2 [Yo-Yo IR1 and IR2] performance: 1790 ± 382 m and 657 ± 225 m, respectively) competitive male ultimate...... = 0.74, p ≤ 0.05). Ultimate Frisbee is an intense intermittent team sport with high cardiovascular loading and clear indications of fatigue toward the end of each half. Yo-Yo IR test performances correlate with physical match performance....

  1. Optimum Safety Levels for Breakwaters

    DEFF Research Database (Denmark)

    Burcharth, H. F.; Sørensen, John Dalsgaard

    2005-01-01

    Optimum design safety levels for rock and cube armoured rubble mound breakwaters without superstructure are investigated by numerical simulations on the basis of minimization of the total costs over the service life of the structure, taking into account typical uncertainties related to wave...... statistics and structure response. The study comprises the influence of interest rate, service lifetime, downtime costs and damage accumulation. Design limit states and safety classes for breakwaters are discussed. The results indicate that optimum safety levels are somewhat higher than the safety levels...

  2. Ultimate and proximate explanations of strong reciprocity.

    Science.gov (United States)

    Vromen, Jack

    2017-08-23

    Strong reciprocity (SR) has recently been subject to heated debate. In this debate, the "West camp" (West et al. in Evol Hum Behav 32(4):231-262, 2011), which is critical of the case for SR, and the "Laland camp" (Laland et al. in Science, 334(6062):1512-1516, 2011, Biol Philos 28(5):719-745, 2013), which is sympathetic to the case of SR, seem to take diametrically opposed positions. The West camp criticizes advocates of SR for conflating proximate and ultimate causation. SR is said to be a proximate mechanism that is put forward by its advocates as an ultimate explanation of human cooperation. The West camp thus accuses advocates of SR for not heeding Mayr's original distinction between ultimate and proximate causation. The Laland camp praises advocates of SR for revising Mayr's distinction. Advocates of SR are said to replace Mayr's uni-directional view on the relation between ultimate and proximate causes by the bi-directional one of reciprocal causation. The paper argues that both the West camp and the Laland camp misrepresent what advocates of SR are up to. The West camp is right that SR is a proximate cause of human cooperation. But rather than putting forward SR as an ultimate explanation, as the West camp argues, advocates of SR believe that SR itself is in need of ultimate explanation. Advocates of SR tend to take gene-culture co-evolutionary theory as the correct meta-theoretical framework for advancing ultimate explanations of SR. Appearances notwithstanding, gene-culture coevolutionary theory does not imply Laland et al.'s notion of reciprocal causation. "Reciprocal causation" suggests that proximate and ultimate causes interact simultaneously, while advocates of SR assume that they interact sequentially. I end by arguing that the best way to understand the debate is by disambiguating Mayr's ultimate-proximate distinction. I propose to reserve "ultimate" and "proximate" for different sorts of explanations, and to use other terms for distinguishing

  3. Optimum target thickness for polarimeters

    International Nuclear Information System (INIS)

    Sitnik, I.M.

    2003-01-01

    Polarimeters with thick targets are a tool to measure the proton polarization. But the question about the optimum target thickness is still the subject of discussion. An attempt to calculate the most common parameters concerning this problem, in a few GeV region, is made

  4. Ultimate justification: Wittgenstein and medical ethics.

    Science.gov (United States)

    Hughes, J

    1995-02-01

    Decisions must be justified. In medical ethics various grounds are given to justify decisions, but ultimate justification seems illusory and little considered. The philosopher Wittgenstein discusses the problem of ultimate justification in the context of general philosophy. His comments, nevertheless, are pertinent to ethics. From a discussion of Wittgensteinian notions, such as 'bedrock', the idea that 'ultimate' justification is grounded in human nature as such is derived. This discussion is relevant to medical ethics in at least five ways: it shows generally what type of certainty there is in practical ethics; it seems to imply some objective foundation to our ethical judgements; it squares with our experience of making ethical decisions; it shows something of the nature of moral arguments; and, finally, it has implications for teaching medicine and ethics.

  5. Optimum design of steel structures

    CERN Document Server

    Farkas, József

    2013-01-01

    This book helps designers and manufacturers to select and develop the most suitable and competitive steel structures, which are safe, fit for production and economic. An optimum design system is used to find the best characteristics of structural models, which guarantee the fulfilment of design and fabrication requirements and minimize the cost function. Realistic numerical models are used as main components of industrial steel structures. Chapter 1 containts some experiences with the optimum design of steel structures Chapter 2 treats some newer mathematical optimization methods. Chapter 3 gives formulae for fabrication times and costs. Chapters 4 deals with beams and columns. Summarizes the Eurocode rules for design. Chapter 5 deals with the design of tubular trusses. Chapter 6 gives the design of frame structures and fire-resistant design rules for a frame. In Chapters 7 some minimum cost design problems of stiffened and cellular plates and shells are worked out for cases of different stiffenings and loads...

  6. Librarians Are the Ultimate Knowledge Managers?

    Science.gov (United States)

    Koina, Cathie

    2003-01-01

    Librarians are the ultimate knowledge managers. Everyone knows that. After all, haven't they been the custodians of documented knowledge for centuries? Who could possibly do it better than them? Well, then why aren't people knocking down their doors, begging them to be the knowledge managers of the organisation? Are they just ignorant of how…

  7. Optimum culture in the cockpit

    Science.gov (United States)

    Yamamori, Hisaaki

    1987-01-01

    Even with the same program and objectives, if the culture is different, there will be different approaches to the goal of flight safety. However, the cockpit environment is culture-free so it is not as important to think of a person's cultural background as it is to think of the approach to the goal of ultimate safety. Crew members can look at their individual safety goals and compare them to their own performance to see if their behavior matches their own safety goals. The cockpit environment must be culture-free in order to obtain the ultimate safety goal. One must first realize how their culture affects their behavior before they can begin to change their attitude and actions in the cockpit.

  8. Ultimate gradient in solid-state accelerators

    International Nuclear Information System (INIS)

    Whittum, D.H.

    1998-08-01

    The authors recall the motivation for research in high-gradient acceleration and the problems posed by a compact collider. They summarize the phenomena known to appear in operation of a solid-state structure with large fields, and research relevant to the question of the ultimate gradient. They take note of new concepts, and examine one in detail, a miniature particle accelerator based on an active millimeter-wave circuit and parallel particle beams

  9. The ultimate disposition of depleted uranium

    Energy Technology Data Exchange (ETDEWEB)

    Lemons, T.R. [Uranium Enrichment Organization, Oak Ridge, TN (United States)

    1991-12-31

    Depleted uranium (DU) is produced as a by-product of the uranium enrichment process. Over 340,000 MTU of DU in the form of UF{sub 6} have been accumulated at the US government gaseous diffusion plants and the stockpile continues to grow. An overview of issues and objectives associated with the inventory management and the ultimate disposition of this material is presented.

  10. Ultimate Strength of Ship Hulls under Torsion

    DEFF Research Database (Denmark)

    Paik, Jeom Kee; Thayamballi, Anil K.; Pedersen, Preben Terndrup

    2001-01-01

    For a ship hull with large deck openings such as container vessels and some large bulk carriers, the analysis of warping stresses and hatch opening deformations is an essential part of ship structural analyses. It is thus of importance to better understand the ultimate torsional strength characte......For a ship hull with large deck openings such as container vessels and some large bulk carriers, the analysis of warping stresses and hatch opening deformations is an essential part of ship structural analyses. It is thus of importance to better understand the ultimate torsional strength...... characteristics of ships with large hatch openings. The primary aim of the present study is to investigate the ultimate strength characteristics of ship hulls with large hatch openings under torsion. Axial (warping) as well as shear stresses are normally developed for thin-walled beams with open cross sections...... subjected to torsion. A procedure for calculating these stresses is briefly described. As an illustrative example, the distribution and magnitude of warping and shear stresses for a typical container vessel hull cross section under unit torsion is calculated by the procedure. By theoretical and numerical...

  11. The ultimate disposition of depleted uranium

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-01

    Significant amounts of the depleted uranium (DU) created by past uranium enrichment activities have been sold, disposed of commercially, or utilized by defense programs. In recent years, however, the demand for DU has become quite small compared to quantities available, and within the US Department of Energy (DOE) there is concern for any risks and/or cost liabilities that might be associated with the ever-growing inventory of this material. As a result, Martin Marietta Energy Systems, Inc. (Energy Systems), was asked to review options and to develop a comprehensive plan for inventory management and the ultimate disposition of DU accumulated at the gaseous diffusion plants (GDPs). An Energy Systems task team, under the chairmanship of T. R. Lemons, was formed in late 1989 to provide advice and guidance for this task. This report reviews options and recommends actions and objectives in the management of working inventories of partially depleted feed (PDF) materials and for the ultimate disposition of fully depleted uranium (FDU). Actions that should be considered are as follows. (1) Inspect UF{sub 6} cylinders on a semiannual basis. (2) Upgrade cylinder maintenance and storage yards. (3) Convert FDU to U{sub 3}O{sub 8} for long-term storage or disposal. This will include provisions for partial recovery of costs to offset those associated with DU inventory management and the ultimate disposal of FDU. Another recommendation is to drop the term tails'' in favor of depleted uranium'' or DU'' because the tails'' label implies that it is waste.'' 13 refs.

  12. Optimum coolant chemistry in BWRs

    International Nuclear Information System (INIS)

    Lin, C.C.; Cowan, R.L.; Kiss, E.

    2004-01-01

    LWR water chemistry parameters are directly or indirectly related to the plant's operational performance and for a significant amount of Operation and Maintenance (O and M) costs. Obvious impacts are the operational costs associated with water treatment, monitoring and associated radwaste generation. Less obvious is the important role water chemistry plays in the magnitude of drywell shutdown dose rates, fuel corrosion performance and, (probably most importantly) materials degradation such as from stress corrosion cracking of piping and Reactor Pressure Vessel (RPV) internal components. To improve the operational excellence of the BWR and to minimize the impact of water chemistry on O and M costs. General Electric has developed the concept of Optimum Water Chemistry (OWC). The 'best practices' and latest technology findings from the U.S., Asia and Europe are integrated into the suggested OWC Specification. This concept, together with cost effective ways to meet the requirement, are discussed. (author)

  13. Rapid population growth and environmental degradation: ultimate versus proximate factors.

    Science.gov (United States)

    Shaw, R P

    1989-01-01

    This philosophical review of 2 arguments about responsibility for and solutions to environmental degradation concludes that both sides are correct: the ultimate and the proximal causes. Ultimate causes of pollution are defined as the technology responsible for a given type of pollution, such as burning fossil fuel; proximate causes are defined as situation-specific factors confounding the problem, such as population density or rate of growth. Commoner and others argue that developed countries with low or negative population growth rates are responsible for 80% of world pollution, primarily in polluting technologies such as automobiles, power generation, plastics, pesticides, toxic wastes, garbage, warfaring, and nuclear weapons wastes. Distortionary policies also contribute; examples are agricultural trade protection, land mismanagement, urban bias in expenditures, and institutional rigidity., Poor nations are responsible for very little pollution because poverty allows little waste or expenditures for polluting, synthetic technologies. The proximal causes of pollution include numbers and rate of growth of populations responsible for the pollution. Since change in the ultimate cause of pollution remains out of reach, altering the numbers of polluters can make a difference. Predictions are made for proportions of the world's total waste production, assuming current 1.6 tons/capita for developed countries and 0.17 tons/capita for developing countries. If developing countries grow at current rates and become more wealthy, they will be emitting half the world's waste by 2025. ON the other hand, unsustainable population growth goes along with inadequate investment in human capital: education, health, employment, infrastructure. The solution is to improve farming technologies in the 117 non-self-sufficient countries, fund development in the most unsustainable enclaves of growing countries, break institutionalized socio-political rigidity in these enclaves, and focus on

  14. Determination of optimum filter in myocardial SPECT: A phantom study

    International Nuclear Information System (INIS)

    Takavar, A.; Shamsipour, Gh.; Sohrabi, M.; Eftekhari, M.

    2004-01-01

    Background: In myocardial perfusion SPECT images are degraded by photon attenuation, the distance-dependent collimator, detector response and photons scatter. Filters greatly affect quality of nuclear medicine images. Materials and Methods: A phantom simulating heart left ventricle was built. About 1mCi of 99m Tc was injected into the phantom. Images was taken from this phantom. Some filters including Parzen, Hamming, Hanning, Butter worth and Gaussian were exerted on the phantom images. By defining some criteria such as contrast, signal to noise ratio, and defect size detectability, the best filter can be determined. Results: 0.325 Nyquist frequency and 0.5 nq was obtained as the optimum cut off frequencies respectively for hamming and handing filters. Order 11, cut off 0.45 Nq and order 20 cut off 0.5 Nq obtained optimum respectively for Butter worth and Gaussian filters. Conclusion: The optimum member of every filter's family was obtained

  15. Ultimately short ballistic vertical graphene Josephson junctions

    Science.gov (United States)

    Lee, Gil-Ho; Kim, Sol; Jhi, Seung-Hoon; Lee, Hu-Jong

    2015-01-01

    Much efforts have been made for the realization of hybrid Josephson junctions incorporating various materials for the fundamental studies of exotic physical phenomena as well as the applications to superconducting quantum devices. Nonetheless, the efforts have been hindered by the diffusive nature of the conducting channels and interfaces. To overcome the obstacles, we vertically sandwiched a cleaved graphene monoatomic layer as the normal-conducting spacer between superconducting electrodes. The atomically thin single-crystalline graphene layer serves as an ultimately short conducting channel, with highly transparent interfaces with superconductors. In particular, we show the strong Josephson coupling reaching the theoretical limit, the convex-shaped temperature dependence of the Josephson critical current and the exceptionally skewed phase dependence of the Josephson current; all demonstrate the bona fide short and ballistic Josephson nature. This vertical stacking scheme for extremely thin transparent spacers would open a new pathway for exploring the exotic coherence phenomena occurring on an atomic scale. PMID:25635386

  16. Ultimate-gradient accelerators physics and prospects

    CERN Document Server

    Skrinsky, Aleksander Nikolayevich

    1995-01-01

    As introduction, the needs and ways for ultimate acceleration gradients are discussed briefly. The Plasma Wake Field Acceleration is analized in the most important details. The structure of specific plasma oscillations and "high energy driver beam SP-plasma" interaction is presented, including computer simulation of the process. Some pratical ways to introduce the necessary mm-scale bunching in driver beam and to arrange sequential energy multiplication are dicussed. The influence of accelerating beam particle - plasma binary collisions is considered, also. As applications of PWFA, the use of proton super-colliders beams (LHC and Future SC) to drive the "multi particle types" accelerator, and the arrangements for the electron-positron TeV range collider are discussed.

  17. Ultimate load capacities of expansion anchor bolts

    International Nuclear Information System (INIS)

    Czarnecki, R.M.; Manrique, M.A.; Samaddar, S.K.

    1993-01-01

    A summary of available experimental expansion anchor bolt test data is presented. These data were collected as part of programs by the nuclear industry to address generic issues related to verification of seismic adequacy of equipment in nuclear power plants. Some of the data presented are suitable for use in seismic probabilistic risk assessments. For example, mean values of ultimate strength, along with their standard deviation and coefficients of variation, for a range of most typical expansion anchor bolt sizes are presented. Effects of interaction between shear and tension, edge distance, spacing, and cracking of the concrete are presented in a manner that is more suitable for use in deterministic evaluations. Related industry programs to derive anchor bolt capacities are briefly discussed. Recommendations for areas of further investigation are also presented

  18. Focused ion beam technology and ultimate applications

    International Nuclear Information System (INIS)

    Gierak, Jacques

    2009-01-01

    In this topical review, the potential of the focused ion beam (FIB) technology and ultimate applications are reviewed. After an introduction to the technology and to the operating principles of liquid metal ion sources (LMIS), of ion optics and instrument architectures, several applications are described and discussed. First, the application of FIB for microcircuit inspection, metrology and failure analysis is presented. Then, we introduce and illustrate some advanced patterning schemes we propose as next generation FIB processing examples. These patterning schemes are (i) local defect injection or smoothing in magnetic thin film direct patterning, (ii) functionalization of graphite substrates to guide organization of clusters, (iii) local and selective epitaxy of III–V semiconductor quantum dots and (iv) FIB patterned solid-state nanopores for biological molecules manipulation and analysis. We conclude this work by giving our vision of the future developments for FIB technology. (topical review)

  19. Transcending matter: physics and ultimate meaning.

    Science.gov (United States)

    Paulson, Steve; Frank, Adam; Kaiser, David; Maudlin, Tim; Natarajan, Priyamvada

    2015-12-01

    From the discovery of new galaxies and nearly undetectable dark energy to the quantum entanglement of particles across the universe, new findings in physics naturally elicit a sense of awe and wonder. For the founders of modern physics-from Einstein and Bohr to Heisenberg, Pauli, and Bohm-a fascination with deeper questions of meaning and ultimate reality led some of them to explore esoteric traditions and metaphysics. More recently, however, physicists have largely shunned such philosophical and spiritual associations. What can contemporary physics offer us in the quest to understand our place in the universe? Has physics in some ways become a religion unto itself that rejects the search for existential meaning? Discussion of these and related questions is presented in this paper. © 2015 New York Academy of Sciences.

  20. UHS, Ultimate Heat Sink Cooling Pond Analysis

    International Nuclear Information System (INIS)

    Codell, R.; Nuttle, W.K.

    1998-01-01

    1 - Description of program or function: Three programs model performance of an ultimate heat sink cooling pond. National Weather Service data is read and analyzed to predict periods of lowest cooling performance and highest evaporative loss. The data is compared to local site data for significant differences. Then the maximum pond temperature is predicted. Five programs model performance of an ultimate heat sink spray pond. The cooling performance, evaporative water loss, and drift water loss as a function of wind speed are estimated for a spray field. These estimates are used in conjunction with National Weather Service data to predict periods of lowest cooling performance and highest evaporative loss. This data is compared to local site data for significant differences. Then the maximum pond temperature is predicted. 2 - Method of solution: The transfer of heat and water vapor is modeled using an equilibrium temperature procedure for an UHS cooling pond. The UHS spray pond model considers heat, mass, and momentum transfer from a single water drop with the surrounding air, and modification of the surrounding air resulting from the heat, mass, and momentum transfer from many drops in different parts of a spray field. 3 - Restrictions on the complexity of the problem: The program SPRCO uses RANF, a uniform random number generator which is an intrinsic function on the CDC. All programs except COMET use the NAMELIST statement, which is non standard. Otherwise these programs conform to the ANSI Fortran 77 standard. The meteorological data scanning procedure requires tens of years of recorded data to be effective. The models and methods, provided as useful tool for UHS analyses of cooling ponds and spray ponds, are intended as guidelines only. Use of these methods does not automatically assure NRC approval, nor are they required procedures for nuclear-power-plant licensing

  1. On the optimum energy mix

    International Nuclear Information System (INIS)

    Fujii, Yasumasa

    2011-01-01

    After the Fukushima accident occurred in March 2011, reform of Japan's basic energy plan and energy supply system was reported to be under discussion such as to reduce dependence on nuclear power. Planning of energy policy should be considered based on four evaluation indexes of 'economics'. 'environmental effects', 'stable supply of energy' and 'sustainability'. 'Stable supply of energy' should include stability of domestic energy supply infrastructure against natural disasters in addition to stable supply of overseas resources. 'Sustainability' meant long-term availability of resources. Since there did not exist an almighty energy source and energy supply system superior in terms of every above-mentioned evaluation index, it would be wise to use combining various energy sources and supply system in rational way. This combination lead to optimum energy mix, so-called 'Energy Best Mix'. The author evaluated characteristics of energy sources and energy supply system in terms of four indexes and showed best energy mix from short-, medium- and long-term perspectives. Since fossil fuel resources would deplete anyhow, it would be inevitable for human being to be dependent on non-fossil energy resources regardless of greenhouse effects. At present it would be difficult and no guarantee to establish society fully dependent on renewable energy, then it would be probable to need utilization of nuclear energy in the long term. (T. Tanaka)

  2. The Ultimate Destination: Choice of Interplanetary Exploration Path can define Future of Interstellar Spaceflight

    Science.gov (United States)

    Silin, D. V.

    Manned interstellar spaceflight is facing multiple challenges of great magnitude; among them are extremely large distances and the lack of known habitable planets other than Earth. Many of these challenges are applicable to manned space exploration within the Solar System to the same or lesser degree. If these issues are resolved on an interplanetary scale, better position to pursue interstellar exploration can be reached. However, very little progress (if any) was achieved in manned space exploration since the end of Space Race. There is no lack of proposed missions, but all of them require considerable technological and financial efforts to implement while yielding no tangible benefits that would justify their costs. To overcome this obstacle highest priority in future space exploration plans should be assigned to the creation of added value in outer space. This goal can be reached if reductions in space transportation, construction and maintenance of space-based structures costs are achieved. In order to achieve these requirements several key technologies have to be mastered, such as near-Earth object mining, space- based manufacturing, agriculture and structure assembly. To keep cost and difficulty under control next exploration steps can be limited to nearby destinations such as geostationary orbit, low lunar orbit, Moon surface and Sun-Earth L1 vicinity. Completion of such a program will create a solid foundation for further exploration and colonization of the Solar System, solve common challenges of interplanetary and interstellar spaceflight and create useful results for the majority of human population. Another important result is that perception of suitable destinations for interstellar missions will change significantly. If it becomes possible to create habitable and self-sufficient artificial environments in the nearby interplanetary space, Earth-like habitable planets will be no longer required to expand beyond our Solar System. Large fraction of the stars in the observable Universe will become valid targets for interstellar missions.

  3. Define Project

    DEFF Research Database (Denmark)

    Munk-Madsen, Andreas

    2005-01-01

    "Project" is a key concept in IS management. The word is frequently used in textbooks and standards. Yet we seldom find a precise definition of the concept. This paper discusses how to define the concept of a project. The proposed definition covers both heavily formalized projects and informally...... organized, agile projects. Based on the proposed definition popular existing definitions are discussed....

  4. "Dermatitis" defined.

    Science.gov (United States)

    Smith, Suzanne M; Nedorost, Susan T

    2010-01-01

    The term "dermatitis" can be defined narrowly or broadly, clinically or histologically. A common and costly condition, dermatitis is underresourced compared to other chronic skin conditions. The lack of a collectively understood definition of dermatitis and its subcategories could be the primary barrier. To investigate how dermatologists define the term "dermatitis" and determine if a consensus on the definition of this term and other related terms exists. A seven-question survey of dermatologists nationwide was conducted. Of respondents (n  =  122), half consider dermatitis to be any inflammation of the skin. Nearly half (47.5%) use the term interchangeably with "eczema." Virtually all (> 96%) endorse the subcategory "atopic" under the terms "dermatitis" and "eczema," but the subcategories "contact," "drug hypersensitivity," and "occupational" are more highly endorsed under the term "dermatitis" than under the term "eczema." Over half (55.7%) personally consider "dermatitis" to have a broad meaning, and even more (62.3%) believe that dermatologists as a whole define the term broadly. There is a lack of consensus among experts in defining dermatitis, eczema, and their related subcategories.

  5. Wall roughness induces asymptotic ultimate turbulence

    Science.gov (United States)

    Zhu, Xiaojue; Verschoof, Ruben A.; Bakhuis, Dennis; Huisman, Sander G.; Verzicco, Roberto; Sun, Chao; Lohse, Detlef

    2018-04-01

    Turbulence governs the transport of heat, mass and momentum on multiple scales. In real-world applications, wall-bounded turbulence typically involves surfaces that are rough; however, characterizing and understanding the effects of wall roughness on turbulence remains a challenge. Here, by combining extensive experiments and numerical simulations, we examine the paradigmatic Taylor-Couette system, which describes the closed flow between two independently rotating coaxial cylinders. We show how wall roughness greatly enhances the overall transport properties and the corresponding scaling exponents associated with wall-bounded turbulence. We reveal that if only one of the walls is rough, the bulk velocity is slaved to the rough side, due to the much stronger coupling to that wall by the detaching flow structures. If both walls are rough, the viscosity dependence is eliminated, giving rise to asymptotic ultimate turbulence—the upper limit of transport—the existence of which was predicted more than 50 years ago. In this limit, the scaling laws can be extrapolated to arbitrarily large Reynolds numbers.

  6. Mesh networks: an optimum solution for AMR

    Energy Technology Data Exchange (ETDEWEB)

    Mimno, G.

    2003-12-01

    Characteristics of mesh networks and the advantage of using them in automatic meter reading equipment (AMR) are discussed. Mesh networks are defined as being similar to a fishing net made of knots and links. In mesh networks the knots represent meter sites and the links are the radio paths between the meter sites and the neighbourhood concentrator. In mesh networks any knot in the communications chain can link to any other and the optimum path is calculated by the network by hopping from meter to meter until the radio message reaches a concentrator. This mesh communications architecture is said to be vastly superior to many older types of radio-based meter reading technologies; its main advantage is that it not only significantly improves the economics of fixed network deployment, but also supports time-of-use metering, remote disconnect services and advanced features, such as real-time pricing, demand response, and other efficiency measures, providing a better return on investment and reliability.

  7. Defining chaos.

    Science.gov (United States)

    Hunt, Brian R; Ott, Edward

    2015-09-01

    In this paper, we propose, discuss, and illustrate a computationally feasible definition of chaos which can be applied very generally to situations that are commonly encountered, including attractors, repellers, and non-periodically forced systems. This definition is based on an entropy-like quantity, which we call "expansion entropy," and we define chaos as occurring when this quantity is positive. We relate and compare expansion entropy to the well-known concept of topological entropy to which it is equivalent under appropriate conditions. We also present example illustrations, discuss computational implementations, and point out issues arising from attempts at giving definitions of chaos that are not entropy-based.

  8. The ultimate challenge of cloacal exstrophy.

    Science.gov (United States)

    Schober, Justine M; Carmichael, Polly A; Hines, Melissa; Ransley, Philip G

    2002-01-01

    Our review addresses the various system abnormalities associated with cloacal exstrophy and revisits the question of gender assignment. Gender assignment decisions and psychological aspects of gender issues have become the "ultimate challenge." Exploration of gender identity, gender role behavior and sexual orientation has just begun. A comprehensive literature review was performed with all world literature regarding the current management of cloacal exstrophy. Research focused on management principles, outcomes and documentation of concurrent anomalies. We also describe original research evaluating gender identity in our own series of patients raised as girls to illustrate the challenge of treatment and augment the available literature, which is scant. Abnormalities of the vertebral column ranged from hemivertebra to myelomeningocele. With magnetic resonance imaging, the incidence of spinal dysraphism approached 100% and cord tethering was also more frequently recognized. For children with the short bowel syndrome, advances in antibiotic usage, and parenteral and enteral nutrition have increased the survival rate and reduced morbidity. A neurological component has been recognized for bladder function, bladder neck continence, lower extremity function and erectile capacity. Mitrofanoff-type reconstruction with bladder neck closure and continent catheterizable stoma dramatically increased continence. Diminutive or absent penis has been documented in 30% of males, and no documentation of paternity exists. The majority of females have bicornuate uterus. However, ovaries and tubes were generally normal. No reports of proven fertility exist. The strategy and timing of surgery relating to gender assignment remain controversial. A desperate need exists for research focusing on gender development and quality of life. Until that time, a cautious watchful approach may be most appropriate as our patients with cloacal exstrophy mature into adulthood.

  9. Defining Cyberbullying.

    Science.gov (United States)

    Englander, Elizabeth; Donnerstein, Edward; Kowalski, Robin; Lin, Carolyn A; Parti, Katalin

    2017-11-01

    Is cyberbullying essentially the same as bullying, or is it a qualitatively different activity? The lack of a consensual, nuanced definition has limited the field's ability to examine these issues. Evidence suggests that being a perpetrator of one is related to being a perpetrator of the other; furthermore, strong relationships can also be noted between being a victim of either type of attack. It also seems that both types of social cruelty have a psychological impact, although the effects of being cyberbullied may be worse than those of being bullied in a traditional sense (evidence here is by no means definitive). A complicating factor is that the 3 characteristics that define bullying (intent, repetition, and power imbalance) do not always translate well into digital behaviors. Qualities specific to digital environments often render cyberbullying and bullying different in circumstances, motivations, and outcomes. To make significant progress in addressing cyberbullying, certain key research questions need to be addressed. These are as follows: How can we define, distinguish between, and understand the nature of cyberbullying and other forms of digital conflict and cruelty, including online harassment and sexual harassment? Once we have a functional taxonomy of the different types of digital cruelty, what are the short- and long-term effects of exposure to or participation in these social behaviors? What are the idiosyncratic characteristics of digital communication that users can be taught? Finally, how can we apply this information to develop and evaluate effective prevention programs? Copyright © 2017 by the American Academy of Pediatrics.

  10. CT4 - Cost-Optimum Procedures

    DEFF Research Database (Denmark)

    Thomsen, Kirsten Engelund; Wittchen, Kim Bjarne

    This report collects the status in European member states regarding implementation of the cos optimum procedure for setting energy performance requirements to new and existing buildings.......This report collects the status in European member states regarding implementation of the cos optimum procedure for setting energy performance requirements to new and existing buildings....

  11. NOAA Optimum Interpolation (OI) SST V2

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The optimum interpolation (OI) sea surface temperature (SST) analysis is produced weekly on a one-degree grid. The analysis uses in situ and satellite SST's plus...

  12. On Optimum Safety Levels of Breakwaters

    DEFF Research Database (Denmark)

    Burcharth, Hans F.; Sørensen, John Dalsgaard

    2006-01-01

    The paper presents results from numerical simulations performed with the objective of identifying optimum design safety levels of conventional rubble mound and caisson breakwaters, corresponding to the lowest costs over the service life of the structures. The work is related to the PIANC Working...... Group 47 on "Selection of type of breakwater structures". The paper summaries results given in Burcharth and Sorensen (2005) related to outer rubble mound breakwaters but focus on optimum safety levels for outer caisson breakwaters on low and high rubble foundations placed on sea beds strong enough...... to resist geotechnical slip failures. Optimum safety levels formulated for use both in deterministic and probabilistic design procedures are given. Results obtained so far indicate that the optimum safety levels for caisson breakwaters are much higher than for rubble mound breakwaters....

  13. NOAA Daily Optimum Interpolation Sea Surface Temperature

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The NOAA 1/4° daily Optimum Interpolation Sea Surface Temperature (or daily OISST) is an analysis constructed by combining observations from different platforms...

  14. Optimum Design of Heat Exchangers Networks Part -I: Software Development

    International Nuclear Information System (INIS)

    Gabr, E.M.A.; EI-Temtamy, S.A.; Deriasl, S.F.; Moustafa, H.A.

    2004-01-01

    In this paper, we have developed a computerized framework for Heat Exchanger Network Synthesis (HENS) with optimality conditions of achieving the least operating and capital cost. The framework of HEN design involves the development three-computer programs, which applied sequentially to design an optimum HEN. The first program Automatic Minimum Utilities [AMU] developed for automatic formulation of LP equations, these equations can be solved by the optimization software [LINDO] to predict minimum hot and cold utilities. The second program based on Vertical Heat Transfer Method [VHTM] for predicting minimum overall heat transfer area and defining the optimum δbT m in. The third program [Mod.RESHEX] developed for targeting of heat transfer area and automatic synthesis of HEN. This program represents the modifications and development of RESHEX method to overcome the design defects, which appeared on original RESHEX applications

  15. Application of customer-interruption costs for optimum distribution planning

    International Nuclear Information System (INIS)

    Mok, Y.L.; Chung, T.S.

    1996-01-01

    We present a new methodology for obtaining optimum values of the integrated cost of utility investment with customer interruption in distribution planning for electric power systems by determining the reliability cost and worth of the distribution system. Reliability cost refers to investment cost of the utility in achieving a defined level of reliability. Reliability worth is the benefit gained by the utility customer from an increase of reliability. A computer program has been developed to determine comparative reliability indices for a typical distribution network. With the average interruption cost, outage duration, average disconnected load, cost data for distribution equipment, etc. being known, the relation between reliability cost, reliability worth and reliability at the specified load point are obtained. The optimum reliability of the distribution system is then determined from the minimum cost to the utility with customer interruption. The applicability of this approach is demonstrated by several practical networks. (Author)

  16. Optimum Stratification of a Skewed Population

    OpenAIRE

    D.K. Rao; M.G.M. Khan; K.G. Reddy

    2014-01-01

    The focus of this paper is to develop a technique of solving a combined problem of determining Optimum Strata Boundaries(OSB) and Optimum Sample Size (OSS) of each stratum, when the population understudy isskewed and the study variable has a Pareto frequency distribution. The problem of determining the OSB isformulated as a Mathematical Programming Problem (MPP) which is then solved by dynamic programming technique. A numerical example is presented to illustrate the compu...

  17. Magnetic surfaces, particle orbits and neutral injection in conventional and ultimate torsatrons

    International Nuclear Information System (INIS)

    Anderson, D.T.; Derr, J.A.; Kruckewitt, T.; Shohet, J.L.; Rehker, S.; Tataronis, J.A.

    1979-01-01

    Capabilities in fully non-axisymmetric numerical methods have resulted in a parametric study of various conventional and ultimate torsatron configurations. No superbananas are found in torsatrons without local magnetic wells. Neutral injection calculations show that, if the vacuum magnetic surfaces are well defined, tangential injection is very efficient

  18. Direct ultimate disposal of spent fuel DEAB. Systems analysis. Ultimate disposal concepts. Final report. Main volume

    International Nuclear Information System (INIS)

    Wahl, A.

    1995-10-01

    The results elaborated under the project, systems analysis of mixed radwaste disposal concepts and systems analysis of ultimate disposal concepts, provide a comprehensive description and assessment of a radwaste repository, for heat generating wastes and for wastes with negligible heat generation, and thus represent the knowledge basis for forthcoming planning work for a repository in an abandoned salt mine. A fact to be considered is that temperature field calculations have shown that there is room for further optimization with regard to the mine layout. The following aspects have been analysed: (1) safety of operation; (2) technical feasibility and realisation and licensability of the concepts; (3) operational aspects; (4) varieties of utilization of the salt dome for the intended purpose (boreholes for waste emplacement, emplacement in galleries, multi-horizon systems); (5) long-term structural stability of the mine; (6) economic efficiency; (7) nuclear materials safeguards. (orig./HP) [de

  19. A New Algorithm for Determining Ultimate Pit Limits Based on Network Optimization

    Directory of Open Access Journals (Sweden)

    Ali Asghar Khodayari

    2013-12-01

    Full Text Available One of the main concerns of the mining industry is to determine ultimate pit limits. Final pit is a collection of blocks, which can be removed with maximum profit while following restrictions on the slope of the mine’s walls. The size, location and final shape of an open-pit are very important in designing the location of waste dumps, stockpiles, processing plants, access roads and other surface facilities as well as in developing a production program. There are numerous methods for designing ultimate pit limits. Some of these methods, such as floating cone algorithm, are heuristic and do not guarantee to generate optimum pit limits. Other methods, like Lerchs–Grossmann algorithm, are rigorous and always generate the true optimum pit limits. In this paper, a new rigorous algorithm is introduced. The main logic in this method is that only positive blocks, which can pay costs of their overlying non-positive blocks, are able to appear in the final pit. Those costs may be paid either by positive block itself or jointly with other positive blocks, which have the same overlying negative blocks. This logic is formulated using a network model as a Linear Programming (LP problem. This algorithm can be applied to two- and three-dimension block models. Since there are many commercial programs available for solving LP problems, pit limits in large block models can be determined easily by using this method.

  20. Educational attainment and ultimate fertility among Swedish women born in 1955-59

    Directory of Open Access Journals (Sweden)

    Gerda Neyer

    2006-05-01

    Full Text Available This is the second of two companion papers addressing the association between educational attainment and fertility for some sixty educational groups of Swedish women, defined according to field of education as well as level of education. The first paper is about childlessness and education, the present one about the mean number of children ever born. We find that ultimate fertility decreases somewhat with an increasing educational level, but its dependence on the field of education is much more impressive. In general, educational groups with relatively little childlessness also have relatively high ultimate fertility, and educational groups with much childlessness have relatively low ultimate fertility. In particular, women educated for the teaching or health-care professions have less childlessness and a higher ultimate fertility than others. Conversely, women with an education for esthetic or (non-teacher humanist occupations have unusually high fractions childless and low ultimate fertility. Women with religious educations stand out by having very high fractions childless but quite ordinary mean ultimate fertility nevertheless; such women have very little childbearing outside of marriage. Women with research degrees have remarkably ordinary childbearing behavior; they do not forego motherhood to the extent that some theories would predict.

  1. The theory of an ‘optimum currency area’

    Directory of Open Access Journals (Sweden)

    Jarosław Kundera

    2012-12-01

    Full Text Available The main goal of this paper is to analyse and distinguish the main components of the theory of an ‘Optimum Currency Area’. The theory of an optimum currency area indicates some essential elements as preconditions for the successful introduction of a common currency: high mobility of labour, openness of the economy defined as a high proportion of tradable to non-tradable goods, and high diversification of domestic production before joining the union. The article’s analysis helps to better understanding the reasons of the current crisis in the euro zone. The main problem with a common currency area is the adjustment to imbalances, which cannot take place through exchange rates in conditions of a common currency. The missing elements of the theory are the role of the mobility of capital to correct interregional balance of payments disequilibria and lack of a common budget with sufficient own resources during the occurrence of debt crises in member countries. The theory of an optimum currency area has noticed the importance of coordination between fiscal and monetary policy and the necessity of redistribution of resources among partners. However, it does not say much about the methods applied, how to deal with debt crises and what the cost of a potential breaking up of monetary union would be.

  2. Determination of optimum filter in inferolateral view of myocardial SPECT

    International Nuclear Information System (INIS)

    Takavar; Eftekhari, M.; Fallahi, B.; Shamsipour, Gh.; Sohrabi, M.; Saghari, M.

    2004-01-01

    Background: In myocardial perfusion SPECT imaging, images are degraded by photon attenuation, distance-dependent collimator, detector response and photon scattering. As filters greatly affect quality of nuclear medicine images, in this study determination of optimum filter for inferolateral view is our prime objective. Materials and Methods: .A phantom simulating heart left ventricle was built. About 1mCi of 99m Tc, was injected into the phantom. Images were taken from this phantom. Parzen, Hamming, Hanning, Butter worth and Gaussian filters were exerted on the images obtained from the phantom.. By defining some criteria such as contrast, signal to noise ratio, and defect size delectability, the best filter was determined for our ADAC spect system at our nuclear medicine center. In this study, 27 patients who previously had undergone coronary angiography were chosen to be included. All of these patients revealed significant stenosis in the left circumflex artery. Myocardial SPECT images of these patients had inferolateral defect. The images of these patients were processed with 12 filters including the optimum filters obtained from phantom study and some other non-optimum filters. A nuclear medicine physician quantified the results by assigmng mark from 0 to 4. to every image. 0 mark for images that didn't show the defect properly and 4 for the best one. The data from patient study were analyzed with non-related, non -parametric Friedman test. Results: Nyquist frequency of 0.325 and 0.5 were obtained as the optimum cut-off frequencies for hamming and Hanning filters respectively. Order 11 and cut-off frequency of 0.45 and order 20. with cut-off frequency of 0.5 were found to be optimum for Butter worth and Gaussian filters. In patient studies it was found that, Butter worth filter with cut-off frequency of 0.45 and order of 11 produced the best quality images. Conclusion: In this study. Butter worth filter with cut-off frequency of 0.45 and order of 11 was the

  3. Optimum Tilt Angle at Tropical Region

    Directory of Open Access Journals (Sweden)

    S Soulayman

    2015-02-01

    Full Text Available : One of the important parameters that affect the performance of a solar collector is its tilt angle with the horizon. This is because of the variation of tilt angle changes the amount of solar radiation reaching the collector surface. Meanwhile, is the rule of thumb, which says that solar collector Equator facing position is the best, is valid for tropical region? Thus, it is required to determine the optimum tilt as for Equator facing and for Pole oriented collectors. In addition, the question that may arise: how many times is reasonable for adjusting collector tilt angle for a definite value of surface azimuth angle? A mathematical model was used for estimating the solar radiation on a tilted surface, and to determine the optimum tilt angle and orientation (surface azimuth angle for the solar collector at any latitude. This model was applied for determining optimum tilt angle and orientation in the tropical zones, on a daily basis, as well as for a specific period. The optimum angle was computed by searching for the values for which the radiation on the collector surface is a maximum for a particular day or a specific period. The results reveal that changing the tilt angle 12 times in a year (i.e. using the monthly optimum tilt angle maintains approximately the total amount of solar radiation near the maximum value that is found by changing the tilt angle daily to its optimum value. This achieves a yearly gain in solar radiation of 11% to 18% more than the case of a solar collector fixed on a horizontal surface.

  4. Ultimate Educational Aims, Overridingness, and Personal Well-Being

    Science.gov (United States)

    Haji, Ishtiyaque; Cuypers, Stefaan E.

    2011-01-01

    Discussion regarding education's aims, especially its ultimate aims, is a key topic in the philosophy of education. These aims or values play a pivotal role in regulating and structuring moral and other types of normative education. We outline two plausible strategies to identify and justify education's ultimate aims. The first associates these…

  5. Sensitivity analysis on ultimate strength of aluminium stiffened panels

    DEFF Research Database (Denmark)

    Rigo, P.; Sarghiuta, R.; Estefen, S.

    2003-01-01

    This paper presents the results of an extensive sensitivity analysis carried out by the Committee III.1 "Ultimate Strength" of ISSC?2003 in the framework of a benchmark on the ultimate strength of aluminium stiffened panels. Previously, different benchmarks were presented by ISSC committees on ul...

  6. Future Synchrotron Light Sources Based on Ultimate Storage Rings

    International Nuclear Information System (INIS)

    Cai, Yunhai

    2012-01-01

    The main purpose of this talk is to describe how far one might push the state of the art in storage ring design. The talk will start with an overview of the latest developments and advances in the design of synchrotron light sources based on the concept of an 'ultimate' storage ring. The review will establish how bright a ring based light source might be, where the frontier of technological challenges are, and what the limits of accelerator physics are. Emphasis will be given to possible improvements in accelerator design and developments in technology toward the goal of achieving an ultimate storage ring. An ultimate storage ring (USR), defined as an electron ring-based light source having an emittance in both transverse planes at the diffraction limit for the range of X-ray wavelengths of interest for a scientific community, would provide very high brightness photons having high transverse coherence that would extend the capabilities of X-ray imaging and probe techniques beyond today's performance. It would be a cost-effective, high-coherence 4th generation light source, competitive with one based on energy recovery linac (ERL) technology, serving a large number of users studying material, chemical, and biological sciences. Furthermore, because of the experience accumulated over many decades of ring operation, it would have the great advantage of stability and reliability. In this paper we consider the design of an USR having 10-pm-rad emittance. It is a tremendous challenge to design a storage ring having such an extremely low emittance, a factor of 100 smaller than those in existing light sources, especially such that it has adequate dynamic aperture and beam lifetime. In many ultra-low emittance designs, the injection acceptances are not large enough for accumulation of the electron beam, necessitating on-axis injection where stored electron bunches are completely replaced with newly injected ones. Recently, starting with the MAX-IV 7-bend achromatic cell, we

  7. Future Synchrotron Light Sources Based on Ultimate Storage Rings

    Energy Technology Data Exchange (ETDEWEB)

    Cai, Yunhai; /SLAC

    2012-04-09

    The main purpose of this talk is to describe how far one might push the state of the art in storage ring design. The talk will start with an overview of the latest developments and advances in the design of synchrotron light sources based on the concept of an 'ultimate' storage ring. The review will establish how bright a ring based light source might be, where the frontier of technological challenges are, and what the limits of accelerator physics are. Emphasis will be given to possible improvements in accelerator design and developments in technology toward the goal of achieving an ultimate storage ring. An ultimate storage ring (USR), defined as an electron ring-based light source having an emittance in both transverse planes at the diffraction limit for the range of X-ray wavelengths of interest for a scientific community, would provide very high brightness photons having high transverse coherence that would extend the capabilities of X-ray imaging and probe techniques beyond today's performance. It would be a cost-effective, high-coherence 4th generation light source, competitive with one based on energy recovery linac (ERL) technology, serving a large number of users studying material, chemical, and biological sciences. Furthermore, because of the experience accumulated over many decades of ring operation, it would have the great advantage of stability and reliability. In this paper we consider the design of an USR having 10-pm-rad emittance. It is a tremendous challenge to design a storage ring having such an extremely low emittance, a factor of 100 smaller than those in existing light sources, especially such that it has adequate dynamic aperture and beam lifetime. In many ultra-low emittance designs, the injection acceptances are not large enough for accumulation of the electron beam, necessitating on-axis injection where stored electron bunches are completely replaced with newly injected ones. Recently, starting with the MAX-IV 7-bend

  8. Common Core: Teaching Optimum Topic Exploration (TOTE)

    Science.gov (United States)

    Karge, Belinda Dunnick; Moore, Roxane Kushner

    2015-01-01

    The Common Core has become a household term and yet many educators do not understand what it means. This article explains the historical perspectives of the Common Core and gives guidance to teachers in application of Teaching Optimum Topic Exploration (TOTE) necessary for full implementation of the Common Core State Standards. An effective…

  9. Optimum fiber distribution in singlewall corrugated fiberboard

    Science.gov (United States)

    Millard W. Johnson; Thomas J. Urbanik; William E. Denniston

    1979-01-01

    Determining optimum distribution of fiber through rational design of corrugated fiberboard could result in significant reductions in fiber required to meet end-use conditions, with subsequent reductions in price pressure and extension of the softwood timber supply. A theory of thin plates under large deformations is developed that is both kinematically and physically...

  10. Calculations enable optimum design of magnetic brake

    Science.gov (United States)

    Kosmahl, H. G.

    1966-01-01

    Mathematical analysis and computations determine optimum magnetic coil configurations for a magnetic brake which controllably decelerates a free falling load to a soft stop. Calculations on unconventionally wound coils determine the required parameters for the desired deceleration with minimum electrical energy supplied to the stationary coil.

  11. Genotype x environment interaction and optimum resource ...

    African Journals Online (AJOL)

    ... x E) interaction and to determine the optimum resource allocation for cassava yield trials. The effects of environment, genotype and G x E interaction were highly significant for all yield traits. Variations due to G x E interaction were greater than those due to genotypic differences for all yield traits. Genotype x location x year ...

  12. Determination of the Optimum Thickness of Approximately ...

    African Journals Online (AJOL)

    In an attempt to conserve the world's scarce energy and material resources, a balance between the cost of heating a material and the optimum thickness of the material becomes vey essential. One of such materials is the local cast aluminium pot commonly used as cooking ware in Nigeria. This paper therefore sets up a ...

  13. Development of the optimum rotor theories

    DEFF Research Database (Denmark)

    Okulov, Valery; Sørensen, Jens Nørkær; van Kuik, Gijs A.M.

    The purpose of this study is the examination of optimum rotor theories with ideal load distributions along the blades, to analyze some of the underlying ideas and concepts, as well as to illuminate them. The book gives the historical background of the issue and presents the analysis of the problems...

  14. Revisiting perceptions of quality of hospice care: managing for the ultimate referral.

    Science.gov (United States)

    Churchman, Richard; York, Grady S; Woodard, Beth; Wainright, Charles; Rau-Foster, Mary

    2014-08-01

    Hospice services provided in the final months of life are delivered through complex interpersonal relationships between caregivers, patients, and families. Often, service value and quality are defined by these interpersonal interactions. This understanding provides hospice leaders with an enormous opportunity to create processes that provide the optimal level of care during the last months of life. The authors argue that the ultimate referral is attained when a family member observes the care of a loved one, and the family member conveys a desire to receive the same quality of services their loved one received at that facility. The point of this article is to provide evidence that supports the methods to ultimately enhance the patient's and family's experience and increase the potential for the ultimate referral. © The Author(s) 2013.

  15. Ultimate Lateral Capacity of Rigid Pile in c- φ Soil

    Science.gov (United States)

    Zhang, Wei-min

    2018-03-01

    To date no analytical solution of the pile ultimate lateral capacity for the general c- φ soil has been obtained. In the present study, a new dimensionless embedded ratio was proposed and the analytical solutions of ultimate lateral capacity and rotation center of rigid pile in c- φ soils were obtained. The results showed that both the dimensionless ultimate lateral capacity and dimensionless rotation center were the univariate functions of the embedded ratio. Also, the ultimate lateral capacity in the c- φ soil was the combination of the ultimate lateral capacity ( f c ) in the clay, and the ultimate lateral capacity ( f φ ) in the sand. Therefore, the Broms chart for clay, solution for clay ( φ=0) put forward by Poulos and Davis, solution for sand ( c=0) obtained by Petrasovits and Awad, and Kondner's ultimate bending moment were all proven to be the special cases of the general solution in the present study. A comparison of the field and laboratory tests in 93 cases showed that the average ratios of the theoretical values to the experimental value ranged from 0.85 to 1.15. Also, the theoretical values displayed a good agreement with the test values.

  16. Influence of initial imperfections on ultimate strength of spherical shells

    Directory of Open Access Journals (Sweden)

    Chang-Li Yu

    2017-09-01

    Full Text Available Comprehensive consideration regarding influence mechanisms of initial imperfections on ultimate strength of spherical shells is taken to satisfy requirement of deep-sea structural design. The feasibility of innovative numerical procedure that combines welding simulation and non-linear buckling analysis is verified by a good agreement to experimental and theoretical results. Spherical shells with a series of wall thicknesses to radius ratios are studied. Residual stress and deformations from welding process are investigated separately. Variant influence mechanisms are discovered. Residual stress is demonstrated to be influential to stress field and buckling behavior but not to the ultimate strength. Deformations are proved to have a significant impact on ultimate strength. When central angles are less than critical value, concave magnitudes reduce ultimate strengths linearly. However, deformations with central angles above critical value are of much greater harm. Less imperfection susceptibility is found in spherical shells with larger wall thicknesses to radius ratios.

  17. Ultimate guide to YouTube for business

    CERN Document Server

    2018-01-01

    Ultimate Guide to YouTube for Business helps small business owners create marketing videos to help promote their products, share their story, build a community around their brand without spending a fortune-all the while making money.

  18. Optimum Operational Parameters for Yawed Wind Turbines

    Directory of Open Access Journals (Sweden)

    David A. Peters

    2011-01-01

    Full Text Available A set of systematical optimum operational parameters for wind turbines under various wind directions is derived by using combined momentum-energy and blade-element-energy concepts. The derivations are solved numerically by fixing some parameters at practical values. Then, the interactions between the produced power and the influential factors of it are generated in the figures. It is shown that the maximum power produced is strongly affected by the wind direction, the tip speed, the pitch angle of the rotor, and the drag coefficient, which are specifically indicated by figures. It also turns out that the maximum power can take place at two different optimum tip speeds in some cases. The equations derived herein can also be used in the modeling of tethered wind turbines which can keep aloft and deliver energy.

  19. OPTIMUM PROGRAMMABLE CONTROL OF UNMANNED FLYING VEHICLE

    Directory of Open Access Journals (Sweden)

    A. А. Lobaty

    2012-01-01

    Full Text Available The paper considers an analytical synthesis problem pertaining to programmable control of an unmanned flying vehicle while steering it to the fixed space point. The problem has been solved while applying a maximum principle which takes into account a final control purpose and its integral expenses. The paper presents an optimum law of controlling overload variation of a flying vehicle that has been obtained analytically

  20. Techniques for evaluating optimum data center operation

    Science.gov (United States)

    Hamann, Hendrik F.; Rodriguez, Sergio Adolfo Bermudez; Wehle, Hans-Dieter

    2017-06-14

    Techniques for modeling a data center are provided. In one aspect, a method for determining data center efficiency is provided. The method includes the following steps. Target parameters for the data center are obtained. Technology pre-requisite parameters for the data center are obtained. An optimum data center efficiency is determined given the target parameters for the data center and the technology pre-requisite parameters for the data center.

  1. Ultimate Opening Combined with Area Stability Applied to Urban Scenes

    OpenAIRE

    Marcotegui , Beatriz; Serna , Andrés; Hernández , Jorge

    2017-01-01

    International audience; This paper explores the use of ultimate opening in urban analysis context. It demonstrates the efficiency of this approach for street level elevation images, derived from 3D point clouds acquired by terrestrial mobile mapping systems. An area-stability term is introduced in the residual definition, reducing the over-segmentation of the vegetation while preserving small significant regions. We compare two possible combinations of the Ultimate Opening and the Area Stabil...

  2. Direct ultimate disposal - state of investigations and prospects

    International Nuclear Information System (INIS)

    Gasterstaedt, N.

    1991-01-01

    Based on a decision adopted by the Prime Ministers on 25/10/90, the principles governing preventive waste management of nuclear power plants are reviewed. Increasing importance is attached to the direct ultimate disposal alternative. The legal and political framework, the technology involved, the state of developments, future activities under the R and D programme as well as a cost estimate of direct ultimate disposal are presented. (orig.) [de

  3. The optimum lead thickness for lead-activation detectors

    International Nuclear Information System (INIS)

    Si Fenni; Hu Qingyuan

    2009-01-01

    The optimum lead thickness for lead-activation detectors has been studied in this paper. First existence of the optimum lead thickness is explained theoretically. Then the optimum lead thickness is obtained by two methods, MCNP5 calculation and mathematical estimation. At last factors which affect the optimum lead thickness are discussed. It turns out that the optimum lead thickness is irrelevant to incident neutron energies. It is recommended 2.5 cm generally.

  4. Optimum MRS site location to minimize spent fuel transportation impacts

    International Nuclear Information System (INIS)

    Hoskins, R.E.

    1987-01-01

    A range of spent fuel transportation system parameters are examined in terms of attributes important to minimizing transportation impacts as a basis for identifying geographic regions best suited for siting a monitored retrievable storage (MRS) facility. Transportation system parameters within existing transport cask design and transportation mode capabilities were systematically analyzed. The optimum MRS location was found to be very sensitive to transportation system assumptions particularly with regard to the relative efficiencies of the reactor-to-MRS and MRS-to-repository components of the system. Moreover, dramatic improvements in the reactor-to-MRS component can be made through use of multiple cask shipment of the largest practical casks by dedicated train compared to the traditional single cask rail (70%) and truck (30%) shipments assumed the Department of Energy in their studies that defined the optimum MRS location in the vicinity of Tennessee. It is important to develop and utilize an efficient transportation system irrespective of whether or not an MRS is in the system. Assuming reasonably achievable efficiency in reactor-to-MRS spent fuel transportation and assigning equal probabilities to the three western sites selected for characterization of being the repository site, the optimum MRS location would be in the far-mid-western states. Based on various geographic criteria including barge access and location in a nuclear service area, the State of Tennessee ranks any place from 12th to the 25th at a penalty of about 30% over the minimum achievable impacts. While minimizing transportation impacts is an important factor, other criteria should also be considered in selecting an MRS site

  5. Ultimate - a new generation of gasoline and diesel fuels; Ultimate - eine neue Generation von Otto- und Dieselkraftstoffen

    Energy Technology Data Exchange (ETDEWEB)

    Strempel, G. [Aral Forschung/Global Fuels Technology, Bochum (Germany); Beckwith, P. [BP Fuels Management Group, Pangbourne (United Kingdom); Froehling, J. [Aral Forschung, Bochum (Germany). Labor/Analytik; Baron, U. [Aral Forschung, Bochum (Germany). Motor- und Fahrzeuglaboratorium; Sauermann, P.; Balfanz, U. [Aral Forschung, Bochum (Germany). Produktentwicklung; Doermer, W. [Aral Forschung, Bochum (Germany). Produktqualitaet

    2005-06-01

    With the launch of Ultimate 100 gasoline and Ultimate Diesel, motorists in Germany now have the opportunity to choose new advanced performance fuels designed to get the very best from their engines. This article gives details of the technical development behind these fuels, their wide range of benefits, and how it is possible to manufacture fuels which meet the considerable technical challenge of achieving both more performance and less pollution. (orig.)

  6. Ultimate load capacity assessment of reinforced concrete shell structures

    International Nuclear Information System (INIS)

    Gupta, Amita; Singh, R.K.; Kushwaha, H.S.; Mahajan, S.C.; Kakodkar, A.

    1993-01-01

    The objective of this study is to develop capability for prediction of ultimate load capacity of reinforced concrete shell structures. The present finite element code ULCA (Ultimate Load Capacity Assessment) adopts a degenerate concept of formulating general isoparametric shell element with a layered approach in the thickness direction. Different failure modes such as crushing, tensile cracking and reinforcement yielding are recognised for various problems. The structure fails by crushing of concrete when the concrete strain/stress reaches the ultimate stress or strain of concrete. Material nonlinearities as a result of tension cracking, tension stiffening between reinforcement and concrete in cracked region and yielding of reinforcement are considered along with geometric nonlinearity. Thus with this code it is possible to predict the pressure at which the first cracking, first through thickness cracking, first yielding of reinforcement occurs. After validating the code with few bench mark problems for different failure modes a reinforced concrete nuclear containment is analysed for its ultimate capacity and the results are matched with the published results. Further the ultimate load capacity of outer containment wall of Narora Atomic Power Station is predicted. It is observed that containment fails in membrane region and has a sufficient margin against design pressure. (author). 9 refs., 56 figs., 3 tabs., 1 appendix with 4 tabs

  7. Design issues for optimum solar cell configuration

    Science.gov (United States)

    Kumar, Atul; Thakur, Ajay D.

    2018-05-01

    A computer based simulation of solar cell structure is performed to study the optimization of pn junction configuration for photovoltaic action. The fundamental aspects of photovoltaic action viz, absorption, separation collection, and their dependence on material properties and deatails of device structures is discussed. Using SCAPS 1D we have simulated the ideal pn junction and shown the effect of band offset and carrier densities on solar cell performance. The optimum configuration can be achieved by optimizing transport of carriers in pn junction under effect of field dependent recombination (tunneling) and density dependent recombination (SRH, Auger) mechanisms.

  8. On the optimum area-balanced filters for nuclear spectroscopy

    International Nuclear Information System (INIS)

    Ripamonti, G.; Pullia, A.

    1996-01-01

    The minimum noise area-balanced (A-B) filters for nuclear spectroscopy are disentangled in the sum of two optimized individual filters. The former is the unipolar finite cusp filter, used for pulse amplitude estimation but affected by baseline shift errors, the latter is a specific filter used for baseline estimation. Each of them is optimized so as to give the minimum noise in the estimation of the pulse amplitude or of its baseline level. It is shown that double optimisation produces an overall optimum filter exhibiting a total noise V 2 n equal to the sum of the noises V 2 n1 and V 2 n2 exhibited by each filter individually. This is a consequence of the orthogonality of the individual filter weight-functions in a function space where the norm is defined as √(V 2 n ). (orig.)

  9. Ductility and Ultimate Capacity of Prestressed Steel Reinforced Concrete Beams

    Directory of Open Access Journals (Sweden)

    Chengquan Wang

    2017-01-01

    Full Text Available Nonlinear numerical analysis of the structural behaviour of prestressed steel reinforced concrete (PSRC beams was carried out by using finite element analysis software ABAQUS. By comparing the load-deformation curves, the rationality and reliability of the finite element model have been confirmed; moreover, the changes of the beam stiffness and stress in the forcing process and the ultimate bearing capacity of the beam were analyzed. Based on the model, the effect of prestressed force, and H-steel to the stiffness, the ultimate bearing capacity and ductility of beam were also analyzed.

  10. Ultimate load model test for Sizewell 'B' primary containment

    International Nuclear Information System (INIS)

    Crowder, R.

    1988-01-01

    This paper considers the factors influencing the adoption of an ultimate load factor for the Sizewell 'B' PWR primary containment structure. As part of the validation process for the ultimate load analysis method, a proposal has been made by Nuclear Design Associates to build and test a 1/10th scale model of the containment structure, which would proceed following the granting of section 2 consent for Sizewell 'B'. The modelling principles, construction method and test proposals are examined in some detail. The proposal is currently being considered by the CEGB's Project Management Team. (author)

  11. ''Project Crystal'' for ultimate storage of highly radioactive waste

    International Nuclear Information System (INIS)

    Anon.

    1983-01-01

    NAGRA (The National Association for storage of radioactive waste) in Baden has launched in North Switzerland an extensive geological research program. The current research program, under the title of ''Project Crystal'', aims at providing the scientific knowledge which is required for the assessment of the suitability of the crystalline sub-soil of North Switzerland for the ultimate storage of highly radioactive waste. Safety and feasibility of such ultimate storage are in the forefront of preoccupations. Scientific institutes of France, Germany, USA and Canada are cooperating more particularly on boring research and laboratory analyses. Technical data are given on the USA and German installations used. (P.F.K.)

  12. Trump er gældsøkonomiens ultimative illusionist

    DEFF Research Database (Denmark)

    Nielsen, Peter

    2018-01-01

    Trump giver ikke kun gevaldige skattelettelser og nærer en illusion om, at vækst vil løse alle problemer. Han fortrænger også gældsøkonomiens ultimative bundlinje i form af klimaforandringerne.......Trump giver ikke kun gevaldige skattelettelser og nærer en illusion om, at vækst vil løse alle problemer. Han fortrænger også gældsøkonomiens ultimative bundlinje i form af klimaforandringerne....

  13. Deposition uniformity, particle nucleation and the optimum conditions for CVD in multi-wafer furnaces

    Energy Technology Data Exchange (ETDEWEB)

    Griffiths, S.K.; Nilson, R.H.

    1996-06-01

    A second-order perturbation solution describing the radial transport of a reactive species and concurrent deposition on wafer surfaces is derived for use in optimizing CVD process conditions. The result is applicable to a variety of deposition reactions and accounts for both diffusive and advective transport, as well as both ordinary and Knudsen diffusion. Based on the first-order approximation, the deposition rate is maximized subject to a constraint on the radial uniformity of the deposition rate. For a fixed reactant mole fraction, the optimum pressure and optimum temperature are obtained using the method of Lagrange multipliers. This yields a weak one-sided maximum; deposition rates fall as pressures are reduced but remain nearly constant at all pressures above the optimum value. The deposition rate is also maximized subject to dual constraints on the uniformity and particle nucleation rate. In this case, the optimum pressure, optimum temperature and optimum reactant fraction are similarly obtained, and the resulting maximum deposition rate is well defined. These results are also applicable to CVI processes used in composites manufacturing.

  14. REGARDING "TRAGIC ECONOMIC OPTIMUM" FROM HOLISTIC+ PERSPECTIVE

    Directory of Open Access Journals (Sweden)

    Constantin Popescu

    2010-12-01

    Full Text Available Communication aims to discuss the new scientific vision of "the entire integrated" as it follows the recent achievements of quantum physics, psychology and biology. From this perspective, economy is seen as a living organism, part of the social organism and together with de bright ecology. The optimum of the economy as a living organism is based on dynamic compatibilities with all common living requirements. The evolution of economic life is organically linked to the unavoidable circumstances contained in the form of V. Frankl ‘s tragic triad consisting of: pain, guilt and death. In interaction with the holistic triad circumscribed by limitations, uncertainties and open interdependencies, the tragic economic optimum (TEO is formed. It can be understood as that state of economic life in which freedom of choice of scarce resources under uncertainty has in the compatibility of rationality and hope the development criteria of MEANING. TEO means to say YES to economic life even in conditions of resource limitations, bankruptcies and unemployment, negative externalities, stress, etc. By respiritualization of responsibility using scientific knowledge. TEO - involves multicriteria modeling of economic life by integrating human demands, community, environmental, spiritual and business development in the assessment predicting human GDP as a variable wave aggregate.

  15. Uniform and Non-Uniform Optimum Scalar Quantizers Performances: A Comparative Study

    Directory of Open Access Journals (Sweden)

    Fendy Santoso

    2008-05-01

    Full Text Available The aim of this research is to investigate source coding, the representation of information source output by finite R bits/symbol. The performance of optimum quantisers subject to an entropy constraint has been studied. The definitive work in this area is best summarised by Shannon’s source coding theorem, that is, a source with entropy H can be encoded with arbitrarily small error probability at any rate R (bits/source output as long as R>H. Conversely, If R the error probability will be driven away from zero, independent of the complexity of the encoder and the decoder employed. In this context, the main objective of engineers is however to design the optimum code. Unfortunately, the rate-distortion theorem does not provide the recipe for such a design. The theorem does, however, provide the theoretical limit so that we know how close we are to the optimum. The full understanding of the theorem also helps in setting the direction to achieve such an optimum. In this research, we have investigated the performances of two practical scalar quantisers, i.e., a Lloyd-Max quantiser and the uniformly defined one and also a well-known entropy coding scheme, i.e., Huffman coding against their theoretically attainable optimum performance due to Shannon’s limit R. It has been shown that our uniformly defined quantiser could demonstrate superior performance. The performance improvements, in fact, are more noticeable at higher bit rates.

  16. Optimum phase shift in the self-oscillating loop for piezoelectric transformer-based power converters

    DEFF Research Database (Denmark)

    Ekhtiari, Marzieh; Zsurzsan, Tiberiu-Gabriel; Andersen, Michael A. E.

    2017-01-01

    A new method is implemented in designing of self-oscillating loop for driving piezoelectric transformers. The implemented method is based on combining both analog and digital control systems. Digitally controlled time delay through the self-oscillating loop results in very precise frequency control...... and ensures optimum operation of the piezoelectric transformer in terms of gain and efficiency. Time delay is implemented digitally for the first time through a 16 bit digital-to-analog converter in the self-oscillating loop. The new design of the delay circuit provides 45 ps time resolution, enabling fine......-grained control of phase in the self-oscillating loop. This allows the control loop to dynamically follow frequency changes of the transformer in each resonant cycle. Ultimately, by selecting the optimum phase shift, maximum efficiency under the load and temperature condition is achievable....

  17. Ultimate deformation capacity of reinforced concrete slabs underblast load

    NARCIS (Netherlands)

    Doormaal, J.C.A.M. van; Weerheijm, J.

    1996-01-01

    In this paper a test method to determine the deformation capacity and the resistance-deformation curve of blast-loaded slabs is described. This method was developed at TNO-PML. The method has been used to determine the ultimate deformation capacity of some simply supported reinforced concrete slabs

  18. 49 Stories That Make an Ultimate STEM Lesson Plan

    Science.gov (United States)

    Mehta, Swati; Mehta, Rohit; Berzina-Pitcher, Inese; Seals, Christopher; Mishra, Punya

    2016-01-01

    In this paper we reviewed what 49 large urban public school district STEM teachers enrolled in a year-long graduate certificate and fellowship program at a large Midwestern university considered as their amazing teaching moments. They were asked to share their amazing teaching moments that would make an Ultimate Lesson Plan in STEM. In smaller…

  19. Ultimate capabilities of soft x-ray optics

    International Nuclear Information System (INIS)

    Vinogradov, A.V.; Zorev, N.N.; Kozhevnikov, I.V.

    1988-01-01

    Nonimaging soft X-ray optics is examined. The ultimate capabilities of a number of X-ray optical components designed for concentration and collimation of radiation from point sources are determined. The applications of X-ray optics are discussed together with the properties of materials in the X-ray range

  20. Safety related aspects of ultimate disposal of radioactive wastes

    International Nuclear Information System (INIS)

    Goemmel, R.

    1992-01-01

    Solutions and questions related to nuclear waste management are presented. In particular, long-term safety of repositories in Germany and Sweden is considered, with special attention being paid to methods of detection, geotechnical barriers and post-operational phase of salt dome repositories, and conditioning of wastes to make them fit for ultimate disposal. (DG) [de

  1. Analysis of ultimate-heat-sink spray ponds. Technical report

    International Nuclear Information System (INIS)

    Codell, R.

    1981-08-01

    This report develops models which can be utilized in the design of certain types of spray ponds used in ultimate heat sinks at nuclear power plants, and ways in which the models may be employed to determine the design basis required by U.S. Nuclear Regulatory Commission Regulatory Guide 1.27

  2. Ultimate internal pressure capacity of concrete containment structures

    International Nuclear Information System (INIS)

    Krishnaswamy, C.N.; Namperumal, R.; Al-Dabbagh, A.

    1983-01-01

    Lesson learned from the accident at Three-Mile Island nuclear plant has necessitated the computation of the ultimate internal pressure capacity of containment structures as a licensing requirement in the U.S. In general, a containment structure is designed to be essentially elastic under design accident pressure. However, as the containment pressure builds up beyond the design value due to a more severe postulated accident, the containment response turns nonlinear as it sequentially passes through cracking of concrete, yielding of linear plate, yielding of rebar, and yielding of post-tensioning tendon (if the containment concrete is prestressed). This paper reports on the determination of the ultimate internal pressure capacity and nonlinear behavior of typical reinforced and prestressed concrete BWR containments. The probable modes of failure, the criteria for ultimate pressure capacity, and the most critical sections are described. Simple equations to hand-calculate the ultimate pressure capacity and the nonlinear behavior at membrane sections of the containment shell are presented. A nonlinear finite element analysis performed to determine the nonlinear behavior of the entire shell including nonmembrane sections is briefly discribed. The analysis model consisted of laminated axisymmetric shell finite elements with nonlinear stress-strain properties for each material. Results presented for typical BWR concrete containments include nonlinear response plots of internal pressure versus containment deflection and strains in the liner, rebar, and post-tensioning tendons at the most stressed section in the shell. Leak-tightness of the containment liner and the effect of thermal loads on the ultimate capacity are discussed. (orig.)

  3. Design chart of optimum current leads

    International Nuclear Information System (INIS)

    Ishibashi, K.; Katase, A.; Maechata, K.

    1986-01-01

    The heat flow through current leads is one of major heat losses in a superconducting magnet system. To reduce the heat flow, current leads have been optimized in a complex way by varying such quantities as conductor length, cross-sectional area, heat transfer coefficient and cooling perimeter. Therefore, this study is made to simplify the design procedure, and to explain the general characteristics of the current leads. A new combined parameter which takes turbulent flow into account is introduced in the present work to enable us to draw a useful design chart. This chart gives, to a wide variety of current leads, detailed information about the optimum design-viz. geometric dimensions, heat flow into liquid helium, and pressure drop of the cooling gas. Change of the cross-sectional area along the conductor may improve the current lead performance. The effects of this area change are examined in detail

  4. Optimum Maintenance Strategies for Highway Bridges

    DEFF Research Database (Denmark)

    Frangopol, Dan M.; Thoft-Christensen, Palle; Das, Parag C.

    As bridges become older and maintenance costs become higher, transportation agencies are facing challenges related to implementation of optimal bridge management programs based on life cycle cost considerations. A reliability-based approach is necessary to find optimal solutions based on minimum...... expected life-cycle costs or maximum life-cycle benefits. This is because many maintenance activities can be associated with significant costs, but their effects on bridge safety can be minor. In this paper, the program of an investigation on optimum maintenance strategies for different bridge types...... is described. The end result of this investigation will be a general reliability-based framework to be used by the UK Highways Agency in order to plan optimal strategies for the maintenance of its bridge network so as to optimize whole-life costs....

  5. Optimum design of a nuclear heat supply

    International Nuclear Information System (INIS)

    Borel, J.P.

    1984-01-01

    This paper presents an economic analysis for the optimum design of a nuclear heat supply to a given district-heating network. First, a general description of the system is given, which includes a nuclear power plant, a heating power plant and a district-heating network. The heating power plant is fed with steam from the nuclear power plant. It is assumed that the heating network is already in operation and that the nuclear power plant was previously designed to supply electricity. Second, a technical definition of the heat production and transportation installations is given. The optimal power of these installations is examined. The main result is a relationship between the network capacity and the level of the nuclear heat supply as a substitute for oil under the best economic conditions. The analysis also presents information for choosing the best operating mode. Finally, the heating power plant is studied in more detail from the energy, technical and economic aspects. (author)

  6. Optimum utilisation of the uranium resource

    International Nuclear Information System (INIS)

    Ion, S. E.; Wilson, P.D.

    1998-01-01

    The nuclear industry faces many challenges, notably to maximise safety, secure an adequate energy supply, manage wastes satisfactorily and achieve political acceptability. One way forward is to optimise together the various interdependent stages of the fuel cycle - the now familiar 'holistic approach'. Many of the issues will demand large R and D expenditure, most effectively met through international collaboration. Sustainable development requires optimum utilisation of energy potential, to which the most accessible key is recycling uranium and the plutonium bred from it. Realising anything like this full potential requires fast-neutron reactors, and therefore BNFL continues to sustain the UK involvement in their international development. Meanwhile, current R and D programmes must aim to make the nuclear option more competitive against fossil resources, while maintaining and developing the necessary skills for more advanced technologies The paper outlines the strategies being pursued and highlights BNFL 's programmes. (author)

  7. Cable tray ultimate strength test employing a large shaker table

    Energy Technology Data Exchange (ETDEWEB)

    Komatsu, K.; Myojin, K.; Imai, K. [The Kansai Electric Power Co., Osaka (Japan); Fuyama, H. [Mitsubishi Heavy Industries Ltd, Takasago (Japan); Kokubo, E. [Mitsubishi Heavy Industdries Ltd, Kobe (Japan)

    2004-07-01

    Ultimate behaviors of cable trays, used in nuclear plants, have not been well studied since cable trays are designed based on conservative design criteria. In this study, by employing a large shaker table, an ultimate strength test was conducted for cable trays used in nuclear power plants. This report describes the results of shaker table test. The following results were obtained. First, in an S{sub 2} earthquake, the damping ratio was so large - more than 30% due to the rubbing of cables - that a large response was not present and the strains in the support were within the elastic limits. Secondly, the support was strong enough to sustain the cable trays even when the strain in the support was 20 times larger than the elastic limit. (authors)

  8. Landau damping: the mechanics model and its ultimate entropy gain

    International Nuclear Information System (INIS)

    Hannay, J H; Kluge, Michel

    2011-01-01

    Classical mechanics has only been invoked to account for Landau damping in a rather half-hearted way, alongside plasma perturbation theory. In particular this invocation is essential for the study of the saturation, or post-linear (or 'nonlinear') regime of the damping initiated by Dawson and O'Neill. By embracing mechanics wholeheartedly here, with its attendant phase space, one can access results, old and new, cleanly and directly, and with one fewer numerical integration for the post-linear regime. By using a summation technique familiar in semiclassical quantum mechanics (Poisson summation), the one remaining numerical integration can be much improved in accuracy. Also accessible from mechanics is the ultimate entropy gain. Though zero for any finite time (in the absence of coarse graining), the entropy gain is ultimately non-zero (at infinite time the required coarse graining is zero). It is calculated analytically by using the appropriate asymptotics, hitherto not fully exploited.

  9. Management and ultimate storage of wastes from nuclear power generation

    International Nuclear Information System (INIS)

    1989-09-01

    The annotation on R and D prorgam 86 parts I-II have been brought together in the present report part I, together with some general viewpoints, and been classified according to subject. Part II of the present report comprises viewpoints of 'Research Program 1987-1992' and part III of 'Alternative methods of ultimate storage'. Swedish and French viewpoints are presented in Swedish, the remaining foreign material in English. The comments are grouped in subject catergories. (O.S.)

  10. The ultimate challenge of pregnancy-associated breast carcinoma

    International Nuclear Information System (INIS)

    Raja, R.; Tahira, A.

    2005-01-01

    Pregnancy associated breast carcinoma requires making judicious use of all diagnostic modalities and the therapeutic options of surgery, irradiation, chemotherapy and hormonal therapy to enhance survival rates. Individualization of treatment for each patient is the key to success. The effects on future fertility, the time interval before next conception, and whether to breast feed or not are all well-documented. A multidisciplinary coordinated team approach to this ultimate challenge of patient care will prove fruitful. (author)

  11. Ultimate Gradient Limitation in Niobium Superconducting Accelerating Cavities

    Energy Technology Data Exchange (ETDEWEB)

    Checchin, Mattia [Illinois Inst. of Technology, Chicago, IL (United States); Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Grassellino, Anna [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Martinello, Martina [Illinois Inst. of Technology, Chicago, IL (United States); Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Posen, Sam [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Romanenko, Alexander [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Zasadzinski, John [Illinois Inst. of Technology, Chicago, IL (United States)

    2016-06-01

    The present study is addressed to the theoretical description of the ultimate gradient limitation in SRF cavities. Our intent is to exploit experimental data to confirm models which provide feed-backs on how to improve the current state-of-art. New theoretical insight on the cavities limiting factor can be suitable to improve the quench field of N-doped cavities, and therefore to take advantage of high Q0 at high gradients.

  12. Ultimate capacity of piles penetrating in weak soil layers

    Directory of Open Access Journals (Sweden)

    Al-Obaidi Ahmed

    2018-01-01

    Full Text Available A pile foundation is one of the most popular forms of deep foundations. They are routinely employed to transfer axial structure loads through the soft soil to stronger bearing strata. Piles generally used to increase the load carrying capacity of the foundation and reduce the settlement of the foundation. On the other hand, many cases in practice where piles pass through different layers of soil that contain weak layers located at different depths and extension, also some time cavities with a different shape, size, and depth are found. In this study, a total of 96 cases is considered and simulated in PLAXIS 2D program aiming to understand the influence of weak soil on the ultimate pile capacity. The piles embedded in the dense sand with a layer of weak soil at different extension and location. The cross section of the geometry used in this study was designed as an axisymmetric model with the 15-node element; the boundary condition recommended at least 5D in the horizontal direction, and (L+5D in the vertical direction where D and L are the diameter and length of pile, respectively. The soil is modeled as Mohr-Coulomb, with five input parameters and the behavior of pile material represented by the linear elastic model. The results of the above cases are compared with the results found in a pile embedded in dense soil without weak layers or cavities. The results indicated that the existence of weak soil layer within the surrounding soil around the pile decreases the ultimate capacity. Furthermore, it has been found that increase in the weak soil width (extension leads to reduction in the ultimate capacity of the pile. This phenomenon is applicable to all depth of weak soil. The influence of weak layer extension on the ultimate capacity is less when it is presentin the upper soil layers.

  13. Ultimate survival in anomalous ψ(2S) decays

    International Nuclear Information System (INIS)

    Gérard, Jean-Marc; Martini, Antony

    2014-01-01

    The hierarchy among the radiative γ(π 0 ,η,η ′ ) decay channels for the ψ ′ looks quite different from the J/ψ one. The fate of charm, namely an ultimate survival of on-shell cc ¯ intermediate states, might give us the clue for this new puzzle in exclusive charmonium decays. A similar self-preservation has already been invoked in the past to solve the so-called ρπ puzzle.

  14. Parametric Study on Ultimate Failure Criteria of Elbow Piping Components in Seismically Isolated NPP

    Energy Technology Data Exchange (ETDEWEB)

    Hahm, Dae Gi; Ki, Min Kyu [KAERI, Daejeon (Korea, Republic of); Jeon, Bub Gyu; Kim, Nam Sik [Pusan National University, Busan (Korea, Republic of)

    2016-05-15

    It is well known that the interface pipes between isolated and non-isolated structures will become the most critical in the seismically isolated NPPs. Therefore, seismic performance of such interface pipes should be evaluated comprehensively especially in terms of the seismic fragility capacity. To evaluate the seismic capacity of interface pipes in the isolated NPP, firstly, we should define the failure mode and failure criteria of critical pipe components. Hence, in this study, we performed the dynamic tests of elbow components which were installed in a seismically isolated NPP, and evaluated the ultimate failure mode and failure criteria by using the test results. To do this, we manufactured 25 critical elbow component specimens and performed cyclic loading tests under the internal pressure condition. The failure mode and failure criteria of a pipe component will be varied by the design parameters such as the internal pressure, pipe diameter, loading type, and loading amplitude. From the tests, we assessed the effects of the variation parameters onto the failure criteria. For the tests, we generated the seismic input protocol of relative displacement between the ends of elbow component. In this paper, elbow in piping system was defined as a fragile element and numerical model was updated by component test. Failure mode of piping component under seismic load was defined by the dynamic tests of ultimate pipe capacity. For the interface piping system, the seismic capacity should be carefully estimated since that the required displacement absorption capacity will be increased significantly by the adoption of the seismic isolation system. In this study, the dynamic tests were performed for the elbow components which were installed in an actual NPPs, and the ultimate failure mode and failure criteria were also evaluated by using the test results.

  15. DETERMINATION of OPTIMUM CONDITION of PAPAIN ENZYME FROM PAPAYA VAR JAVA (Carica papaya

    Directory of Open Access Journals (Sweden)

    Aline Puspita Kusumadjaja

    2010-06-01

    Full Text Available A study to investigate the optimum condition of papain enzyme has been carried out. The condition that are investigated are pH and temperature, based on measurement of enzyme activity which is defined as mmole tyrosin that are released in reaction between papain enzyme and casein as substrat per minute. In this research, the papain enzyme was isolated from pepaya burung varietas Java. The enzyme was partially purified by precipitation method using 30% - 50% saturated acetone. The result showed that the optimum conditions of papain enzyme are in pH 6 with activity 2,606 U/mL, and temperature at 50 oC with activity 2,469 U/mL. Keywords : Papaya var Java, papain, optimum condition, enzymatic activity

  16. Hydrogeological problems in the ultimate storage of radioactive wastes

    International Nuclear Information System (INIS)

    Uerpmann, E.P.

    1980-01-01

    The following work shows how one can achieve the safe closure of ultimate-stored radioactive wastes by connecting a series of various barriers to the biosphere. The propagation of radionuclides by ground water is considered to be the most important long-term transport mechanism. Salt occurences in the Federal Republic of Germany are considered to be the best form suitable for end storage formations for known reasons. When not observing mining and hydrogeological knowledge, the danger of uncontrollable water flow in the end storage can arise from the water solubility of the salt rocks. Therefore the filling of salt mines and the subsequent procedures are dealt with in detail. The leading of radioactive nuclides is influenced by the properties of the ultimately stored wastes and by the quality of the remaining filling of the caves. These problems are dealt with in detail. A series of barriers to the closure of the underground caves are suggested and discussed. The most important barriers consist of the stability of the corresponding selected end storage structure. Possible arrangements of the storage cave are given which even after storage must maintain a high stability. Proposals are made on how the ultimately stored wastes can protect themselves against contact with free water or salt solutions. (orig.) [de

  17. Ultimate concerns in late modernity: Archer, Bourdieu and reflexivity.

    Science.gov (United States)

    Farrugia, David; Woodman, Dan

    2015-12-01

    Through a critique of Margaret Archer's theory of reflexivity, this paper explores the theoretical contribution of a Bourdieusian sociology of the subject for understanding social change. Archer's theory of reflexivity holds that conscious 'internal conversations' are the motor of society, central both to human subjectivity and to the 'reflexive imperative' of late modernity. This is established through critiques of Bourdieu, who is held to erase creativity and meaningful personal investments from subjectivity, and late modernity is depicted as a time when a 'situational logic of opportunity' renders embodied dispositions and the reproduction of symbolic advantages obsolete. Maintaining Archer's focus on 'ultimate concerns' in a context of social change, this paper argues that her theory of reflexivity is established through a narrow misreading and rejection of Bourdieu's work, which ultimately creates problems for her own approach. Archer's rejection of any pre-reflexive dimensions to subjectivity and social action leaves her unable to sociologically explain the genesis of 'ultimate concerns', and creates an empirically dubious narrative of the consequences of social change. Through a focus on Archer's concept of 'fractured reflexivity', the paper explores the theoretical necessity of habitus and illusio for understanding the social changes that Archer is grappling with. In late modernity, reflexivity is valorized just as the conditions for its successful operation are increasingly foreclosed, creating 'fractured reflexivity' emblematic of the complex contemporary interaction between habitus, illusio, and accelerating social change. © London School of Economics and Political Science 2015.

  18. An Optimum Solution for Electric Power Theft

    Directory of Open Access Journals (Sweden)

    Aamir Hussain Memon

    2013-07-01

    Full Text Available Electric power theft is a problem that continues to plague power sector across the whole country. Every year, the electricity companies face the line losses at an average 20-30% and according to power ministry estimation WAPDA companies lose more than Rs. 125 billion. Significantly, it is enough to destroy the entire power sector of country. According to sources 20% losses means the masses would have to pay extra 20% in terms of electricity tariffs. In other words, the innocent consumers pay the bills of those who steal electricity. For all that, no any permanent solution for this major issue has ever been proposed. We propose an applicable and optimum solution for this impassable problem. In our research, we propose an Electric power theft solution based on three stages; Transmission stage, Distribution stage, and User stage. Without synchronization among all, the complete solution can not be achieved. The proposed solution is simulated on NI (National Instruments Circuit Design Suite Multisim v.10.0. Our research work is an implicit and a workable approach towards the Electric power theft, as for conditions in Pakistan, which is bearing the brunt of power crises already

  19. Optimum harvest maturity for Leymus chinensis seed

    Directory of Open Access Journals (Sweden)

    Jixiang Lin

    2016-06-01

    Full Text Available Timely harvest is critical to achieve maximum seed viability and vigour in agricultural production. However, little information exists concerning how to reap the best quality seeds of Leymus chinensis, which is the dominant and most promising grass species in the Songnen Grassland of Northern China. The objective of this study was to investigate and evaluate possible quality indices of the seeds at different days after peak anthesis. Seed quality at different development stages was assessed by the colours of the seed and lemmas, seed weight, moisture content, electrical conductivity of seed leachate and germination indices. Two consecutive years of experimental results showed that the maximum seed quality was recorded at 39 days after peak anthesis. At this date, the colours of the seed and lemmas reached heavy brown and yellow, respectively. The seed weight was highest and the moisture content and the electrical conductivity of seed leachate were lowest. In addition, the seed also reached its maximum germination percentage and energy at this stage, determined using a standard germination test (SGT and accelerated ageing test (AAT. Thus, Leymus chinensis can be harvested at 39 days after peak anthesis based on the changes in parameters. Colour identification can be used as an additional indicator to provide a more rapid and reliable measure of optimum seed maturity; approximately 10 days after the colour of the lemmas reached yellow and the colour of the seed reached heavy brown, the seed of this species was suitable for harvest.

  20. Designing from minimum to optimum functionality

    Science.gov (United States)

    Bannova, Olga; Bell, Larry

    2011-04-01

    This paper discusses a multifaceted strategy to link NASA Minimal Functionality Habitable Element (MFHE) requirements to a compatible growth plan; leading forward to evolutionary, deployable habitats including outpost development stages. The discussion begins by reviewing fundamental geometric features inherent in small scale, vertical and horizontal, pressurized module configuration options to characterize applicability to meet stringent MFHE constraints. A proposed scenario to incorporate a vertical core MFHE concept into an expanded architecture to provide continuity of structural form and a logical path from "minimum" to "optimum" design of a habitable module. The paper describes how habitation and logistics accommodations could be pre-integrated into a common Hab/Log Module that serves both habitation and logistics functions. This is offered as a means to reduce unnecessary redundant development costs and to avoid EVA-intensive on-site adaptation and retrofitting requirements for augmented crew capacity. An evolutionary version of the hard shell Hab/Log design would have an expandable middle section to afford larger living and working accommodations. In conclusion, the paper illustrates that a number of cargo missions referenced for NASA's 4.0.0 Lunar Campaign Scenario could be eliminated altogether to expedite progress and reduce budgets. The plan concludes with a vertical growth geometry that provides versatile and efficient site development opportunities using a combination of hard Hab/Log modules and a hybrid expandable "CLAM" (Crew Lunar Accommodations Module) element.

  1. Achieving optimum diffraction based overlay performance

    Science.gov (United States)

    Leray, Philippe; Laidler, David; Cheng, Shaunee; Coogans, Martyn; Fuchs, Andreas; Ponomarenko, Mariya; van der Schaar, Maurits; Vanoppen, Peter

    2010-03-01

    Diffraction Based Overlay (DBO) metrology has been shown to have significantly reduced Total Measurement Uncertainty (TMU) compared to Image Based Overlay (IBO), primarily due to having no measurable Tool Induced Shift (TIS). However, the advantages of having no measurable TIS can be outweighed by increased susceptibility to WIS (Wafer Induced Shift) caused by target damage, process non-uniformities and variations. The path to optimum DBO performance lies in having well characterized metrology targets, which are insensitive to process non-uniformities and variations, in combination with optimized recipes which take advantage of advanced DBO designs. In this work we examine the impact of different degrees of process non-uniformity and target damage on DBO measurement gratings and study their impact on overlay measurement accuracy and precision. Multiple wavelength and dual polarization scatterometry are used to characterize the DBO design performance over the range of process variation. In conclusion, we describe the robustness of DBO metrology to target damage and show how to exploit the measurement capability of a multiple wavelength, dual polarization scatterometry tool to ensure the required measurement accuracy for current and future technology nodes.

  2. Ultimate load design and testing of a cylindrical prestressed concrete vessel

    International Nuclear Information System (INIS)

    Stefanou, G.D.

    1982-01-01

    The object of this research was to design, construct and test to failure a prestressed concrete pressure vessel model that could be used to investigate the behavior of a full scale structure underworking and ultimate load. The properties and the design of the model was based generally on full scale vessels already constructed to house the nuclear reactors used in atomic power stations. To design the model the ultimate load approach was adopted throughout. All load factors associated with the prestressing have been defined and kept to a minimum in order that the vessel's behavior may be predicted. The tests on the vessel were carried out first on the elastic range to observe its behavior at working load and then at the ultimate range to observe the modes of failure and compare the actual results in both cases with the predicted values. Although full agreement between observed results and predicted values was not obtained, the conclusions drawn from the study were useful for the design of full scale vessels. (author)

  3. Adobe Photoshop CS5 for Photographers The Ultimate Workshop

    CERN Document Server

    Evening, Martin

    2010-01-01

    If you already have a good knowledge of Adobe Photoshop and are looking to advance your skills, Adobe Photoshop CS5 for Photographers: The Ultimate Workshop is the book you've been waiting for.  Renowned photographers Martin Evening and Jeff Schewe impart their Photoshop tips and workflow, showing you how to use a vast array of rarely seen advanced Photoshop techniques.  Whether the subject is serious retouching work, weird and wonderful compositions, or planning a shoot before you've even picked up a camera, you can be sure that the advice is based on years of practical experience.

  4. Ultimate survival in anomalous ψ(2S) decays

    Energy Technology Data Exchange (ETDEWEB)

    Gérard, Jean-Marc; Martini, Antony

    2014-03-07

    The hierarchy among the radiative γ(π{sup 0},η,η{sup ′}) decay channels for the ψ{sup ′} looks quite different from the J/ψ one. The fate of charm, namely an ultimate survival of on-shell cc{sup ¯} intermediate states, might give us the clue for this new puzzle in exclusive charmonium decays. A similar self-preservation has already been invoked in the past to solve the so-called ρπ puzzle.

  5. Determination of Ultimate Torque for Multiply Connected Cross Section Rod

    Directory of Open Access Journals (Sweden)

    V. L. Danilov

    2015-01-01

    Full Text Available The aim of this work is to determine load-carrying capability of the multiply cross-section rod. This calculation is based on the model of the ideal plasticity of the material, so that the desired ultimate torque is a torque at which the entire cross section goes into a plastic state.The article discusses the cylindrical multiply cross-section rod. To satisfy the equilibrium equation and the condition of plasticity simultaneously, two stress function Ф and φ are introduced. By mathematical transformations it has been proved that Ф is constant along the path, and a formula to find its values on the contours has been obtained. The paper also presents the rationale of the line of stress discontinuity and obtained relationships, which allow us to derive the equations break lines for simple interaction of neighboring circuits, such as two lines, straight lines and circles, circles and a different sign of the curvature.After substitution into the boundary condition at the end of the stress function Ф and mathematical transformations a formula is obtained to determine the ultimate torque for the multiply cross-section rod.Using the doubly connected cross-section and three-connected cross-section rods as an example the application of the formula of ultimate torque is studied.For doubly connected cross-section rod, the paper offers a formula of the torque versus the radius of the rod, the aperture radius and the distance between their centers. It also clearly demonstrates the torque dependence both on the ratio of the radii and on the displacement of hole. It is shown that the value of the torque is more influenced by the displacement of hole, rather than by the ratio of the radii.For the three-connected cross-section rod the paper shows the integration feature that consists in selection of a coordinate system. As an example, the ultimate torque is found by two methods: analytical one and 3D modeling. The method of 3D modeling is based on the Nadai

  6. Implementation of optimum solar electricity generating system

    International Nuclear Information System (INIS)

    Singh, Balbir Singh Mahinder; Karim, Samsul Ariffin A.; Sivapalan, Subarna; Najib, Nurul Syafiqah Mohd; Menon, Pradeep

    2014-01-01

    Under the 10 th Malaysian Plan, the government is expecting the renewable energy to contribute approximately 5.5% to the total electricity generation by the year 2015, which amounts to 98MW. One of the initiatives to ensure that the target is achievable was to establish the Sustainable Energy Development Authority of Malaysia. SEDA is given the authority to administer and manage the implementation of the feed-in tariff (FiT) mechanism which is mandated under the Renewable Energy Act 2011. The move to establish SEDA is commendable and the FiT seems to be attractive but there is a need to create awareness on the implementation of the solar electricity generating system (SEGS). In Malaysia, harnessing technologies related to solar energy resources have great potential for implementation. However, the main issue that plagues the implementation of SEGS is the intermittent nature of this source of energy. The availability of sunlight is during the day time, and there is a need for electrical energy storage system, so that there is electricity available during the night time as well. The meteorological condition such as clouds, haze and pollution affects the SEGS as well. The PV based SEGS is seems to be promising electricity generating system that can contribute towards achieving the 5.5% target and will be able to minimize the negative effects of utilizing fossil fuels for electricity generation on the environment. Malaysia is committed to Kyoto Protocol, which emphasizes on fighting global warming by achieving stabilization of greenhouse gas concentrations in the atmosphere at a level that would prevent dangerous anthropogenic interference with the climate system. In this paper, the technical aspects of the implementation of optimum SEGS is discussed, especially pertaining to the positioning of the PV panels

  7. Implementation of optimum solar electricity generating system

    Science.gov (United States)

    Singh, Balbir Singh Mahinder; Sivapalan, Subarna; Najib, Nurul Syafiqah Mohd; Menon, Pradeep; Karim, Samsul Ariffin A.

    2014-10-01

    Under the 10th Malaysian Plan, the government is expecting the renewable energy to contribute approximately 5.5% to the total electricity generation by the year 2015, which amounts to 98MW. One of the initiatives to ensure that the target is achievable was to establish the Sustainable Energy Development Authority of Malaysia. SEDA is given the authority to administer and manage the implementation of the feed-in tariff (FiT) mechanism which is mandated under the Renewable Energy Act 2011. The move to establish SEDA is commendable and the FiT seems to be attractive but there is a need to create awareness on the implementation of the solar electricity generating system (SEGS). In Malaysia, harnessing technologies related to solar energy resources have great potential for implementation. However, the main issue that plagues the implementation of SEGS is the intermittent nature of this source of energy. The availability of sunlight is during the day time, and there is a need for electrical energy storage system, so that there is electricity available during the night time as well. The meteorological condition such as clouds, haze and pollution affects the SEGS as well. The PV based SEGS is seems to be promising electricity generating system that can contribute towards achieving the 5.5% target and will be able to minimize the negative effects of utilizing fossil fuels for electricity generation on the environment. Malaysia is committed to Kyoto Protocol, which emphasizes on fighting global warming by achieving stabilization of greenhouse gas concentrations in the atmosphere at a level that would prevent dangerous anthropogenic interference with the climate system. In this paper, the technical aspects of the implementation of optimum SEGS is discussed, especially pertaining to the positioning of the PV panels.

  8. Implementation of optimum solar electricity generating system

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Balbir Singh Mahinder, E-mail: balbir@petronas.com.my; Karim, Samsul Ariffin A., E-mail: samsul-ariffin@petronas.com.my [Department of Fundamental and Applied Sciences, Universiti Teknologi PETRONAS, 31750 Bandar Seri Iskandar, Perak (Malaysia); Sivapalan, Subarna, E-mail: subarna-sivapalan@petronas.com.my [Department of Management and Humanities, Universiti Teknologi PETRONAS, 31750 Bandar Seri Iskandar, Perak (Malaysia); Najib, Nurul Syafiqah Mohd; Menon, Pradeep [Department of Electrical and Electronics Engineering, Universiti Teknologi PETRONAS, 31750 Bandar Seri Iskandar, Perak (Malaysia)

    2014-10-24

    Under the 10{sup th} Malaysian Plan, the government is expecting the renewable energy to contribute approximately 5.5% to the total electricity generation by the year 2015, which amounts to 98MW. One of the initiatives to ensure that the target is achievable was to establish the Sustainable Energy Development Authority of Malaysia. SEDA is given the authority to administer and manage the implementation of the feed-in tariff (FiT) mechanism which is mandated under the Renewable Energy Act 2011. The move to establish SEDA is commendable and the FiT seems to be attractive but there is a need to create awareness on the implementation of the solar electricity generating system (SEGS). In Malaysia, harnessing technologies related to solar energy resources have great potential for implementation. However, the main issue that plagues the implementation of SEGS is the intermittent nature of this source of energy. The availability of sunlight is during the day time, and there is a need for electrical energy storage system, so that there is electricity available during the night time as well. The meteorological condition such as clouds, haze and pollution affects the SEGS as well. The PV based SEGS is seems to be promising electricity generating system that can contribute towards achieving the 5.5% target and will be able to minimize the negative effects of utilizing fossil fuels for electricity generation on the environment. Malaysia is committed to Kyoto Protocol, which emphasizes on fighting global warming by achieving stabilization of greenhouse gas concentrations in the atmosphere at a level that would prevent dangerous anthropogenic interference with the climate system. In this paper, the technical aspects of the implementation of optimum SEGS is discussed, especially pertaining to the positioning of the PV panels.

  9. 75 FR 60133 - Agency Information Collection Activities: Declaration of Ultimate Consignee That Articles Were...

    Science.gov (United States)

    2010-09-29

    ... Activities: Declaration of Ultimate Consignee That Articles Were Exported for Temporary Scientific or... the Declaration of Ultimate Consignee That Articles Were Exported for Temporary Scientific or...: Title: Declaration of Ultimate Consignee That Articles Were Exported for Temporary Scientific or...

  10. The prospects of transition metal dichalcogenides for ultimately scaled CMOS

    Science.gov (United States)

    Thiele, S.; Kinberger, W.; Granzner, R.; Fiori, G.; Schwierz, F.

    2018-05-01

    MOSFET gate length scaling has been a main source of progress in digital electronics for decades. Today, researchers still spend considerable efforts on reducing the gate length and on developing ultimately scaled MOSFETs, thereby exploring both new device architectures and alternative channel materials beyond Silicon such as two-dimensional TMDs (transition metal dichalcogenide). On the other hand, the envisaged scaling scenario for the next 15 years has undergone a significant change recently. While the 2013 ITRS edition required a continuation of aggressive gate length scaling for at least another 15 years, the 2015 edition of the ITRS suggests a deceleration and eventually a levelling off of gate length scaling and puts more emphasis on alternative options such as pitch scaling to keep Moore's Law alive. In the present paper, future CMOS scaling is discussed in the light of emerging two-dimensional MOSFET channel, in particular two-dimensional TMDs. To this end, the scaling scenarios of the 2013 and 2015 ITRS editions are considered and the scaling potential of TMD MOSFETs is investigated by means of quantum-mechanical device simulations. It is shown that for ultimately scaled MOSFETs as required in the 2013 ITRS, the heavy carrier effective masses of the Mo- and W-based TMDs are beneficial for the suppression of direct source-drain tunneling, while to meet the significantly relaxed scaling targets of the 2016 ITRS heavy-effective-mass channels are not needed.

  11. The ultimate security bounds of quantum key distribution protocols

    International Nuclear Information System (INIS)

    Nikolopoulos, G.M.; Alber, G.

    2005-01-01

    Full text: Quantum key distribution (QKD) protocols exploit quantum correlations in order to establish a secure key between two legitimate users. Recent work on QKD has revealed a remarkable link between quantum and secret correlations. In this talk we report on recent results concerning the ultimate upper security bounds of various QKD schemes (i.e., the maximal disturbance up to which the two legitimate users share quantum correlations) under the assumption of general coherent attacks. In particular, we derive an analytic expression for the ultimate upper security bound of QKD schemes that use two mutually unbiased bases. As long as the two legitimate users focus on the sifted key and treat each pair of data independently during the post processing, our results are valid for arbitrary dimensions of the information carriers. The bound we have derived is well below the predictions of optimal cloning machines. The possibility of extraction of a secret key beyond entanglement distillation is also discussed. In the case of qutrits we argue that any eavesdropping strategy is equivalent to a symmetric one. For higher dimensions, however, such equivalence is generally no longer valid. (author)

  12. Ultimate internal pressure capacity assessment of SC structure

    International Nuclear Information System (INIS)

    Park, Hyungkui; Choi, Inkil

    2013-01-01

    An SC structure applied to a containment building can be quite effective. However, an SC structure cannot be applied to a containment building, because its internal pressure resistance performance has not been verified. The containment building, which undergoes ultimate internal pressure, resists the internal pressure through a pre-stress tendon. It is hard to apply a tendon to an SC structure because of its structural characteristics. Therefore, the internal pressure resistance performance of the SC structure itself should be ensured to apply it to a structure with internal pressure resistance. In this study, the suitability of an SC structure as a substitution for the tendon of a pressure resistant structure was evaluated. A containment structure model was used in this study, because it was representative structures that resistance of ultimate internal pressure be required. In this study, a nonlinear analysis was performed to evaluate and compare the behaviors of tendon model and SC structure model. By comparing the internal pressure-displacement according to the structure type, the stability of SC structure model was assessed

  13. Optimum gain and phase for stochastic cooling systems

    International Nuclear Information System (INIS)

    Meer, S. van der.

    1984-01-01

    A detailed analysis of optimum gain and phase adjustment in stochastic cooling systems reveals that the result is strongly influenced by the beam feedback effect and that for optimum performance the system phase should change appreciably across each Schottky band. It is shown that the performance is not greatly diminished if a constant phase is adopted instead. On the other hand, the effect of mixing between pick-up and kicker (which produces a phase change similar to the optimum one) is shown to be less perturbing than is usually assumed, provided that the absolute value of the gain is not too far from the optimum value. (orig.)

  14. Generalized Pareto optimum and semi-classical spinors

    Science.gov (United States)

    Rouleux, M.

    2018-02-01

    In 1971, S. Smale presented a generalization of Pareto optimum he called the critical Pareto set. The underlying motivation was to extend Morse theory to several functions, i.e. to find a Morse theory for m differentiable functions defined on a manifold M of dimension ℓ. We use this framework to take a 2 × 2 Hamiltonian ℋ = ℋ(p) ∈ 2 C ∞(T * R 2) to its normal form near a singular point of the Fresnel surface. Namely we say that ℋ has the Pareto property if it decomposes, locally, up to a conjugation with regular matrices, as ℋ(p) = u ‧(p)C(p)(u ‧(p))*, where u : R 2 → R 2 has singularities of codimension 1 or 2, and C(p) is a regular Hermitian matrix (“integrating factor”). In particular this applies in certain cases to the matrix Hamiltonian of Elasticity theory and its (relative) perturbations of order 3 in momentum at the origin.

  15. Evaluation of the optimum region for mammographic system using computer simulation to study modulation transfer functions

    International Nuclear Information System (INIS)

    Oliveira, Isaura N. Sombra; Schiable, Homero; Porcel, Naider T.; Frere, Annie F.; Marques, Paulo M.A.

    1996-01-01

    An investigation of the 'optimum region' of the radiation field considering mammographic systems is studied. Such a region was defined in previous works as the field range where the system has its best performance and sharpest images. This study is based on a correlation of two methods for evaluating radiologic imaging systems, both using computer simulation in order to determine modulation transfer functions (MTFs) due to the X-ray tube focal spot in several field orientation and locations

  16. On the ultimate uncertainty of the top quark pole mass

    Energy Technology Data Exchange (ETDEWEB)

    Beneke, M. [Technische Univ. Muenchen, Garching (Germany). Physik-Department; Marquard, P. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Nason, P. [INFN, Sezione di Milano Bicocca (Italy); Steinhauser, M. [Karlsruher Institut fuer Technologie (Germany). Inst. fuer Theoretische Teilchenphysik

    2016-05-15

    We combine the known asymptotic behaviour of the QCD perturbation series expansion, which relates the pole mass of a heavy quark to the MS mass, with the exact series coefficients up to the four-loop order to determine the ultimate uncertainty of the top-quark pole mass due to the renormalon divergence. We perform extensive tests of our procedure by varying the number of colours and flavours, as well as the scale of the strong coupling and the MS mass, and conclude that this uncertainty is around 70 MeV. We further estimate the additional contribution to the mass relation from the five-loop correction and beyond to be 250 MeV.

  17. On the ultimate uncertainty of the top quark pole mass

    International Nuclear Information System (INIS)

    Beneke, M.; Nason, P.; Steinhauser, M.

    2016-05-01

    We combine the known asymptotic behaviour of the QCD perturbation series expansion, which relates the pole mass of a heavy quark to the MS mass, with the exact series coefficients up to the four-loop order to determine the ultimate uncertainty of the top-quark pole mass due to the renormalon divergence. We perform extensive tests of our procedure by varying the number of colours and flavours, as well as the scale of the strong coupling and the MS mass, and conclude that this uncertainty is around 70 MeV. We further estimate the additional contribution to the mass relation from the five-loop correction and beyond to be 250 MeV.

  18. ONE FINANCIAL REPORTING GLOBAL LANGUAGE: THE ULTIMATE GOAL?

    Directory of Open Access Journals (Sweden)

    Amelia Limijaya

    2017-05-01

    Full Text Available This article aims to analyse the extent to which international accounting standards is applied and whether it is the ultimate goal. Up until the end of 2016, approximately there are 84% of the 149 jurisdictions analysed which require IFRS for all or most domestic publicly accountable entities. This may indicate that we are not that much further from having a single set of globally-accepted accounting standards. However, there is more to financial reporting than just accounting standards alone, such as the political aspect of accounting standard-setting, translation issues surrounding IFRS adoption, the US position and the complexity of financial reporting. Improving financial reporting quality needs more than just having global accounting standards, rather, it is also essential to consider the preparers’ incentives and other institutions surrounding the firm. Stakeholders need to broaden the perspective when viewing financial reporting, so that it will not be focused merely on accounting standards alone.

  19. On the ultimate uncertainty of the top quark pole mass

    Science.gov (United States)

    Beneke, M.; Marquard, P.; Nason, P.; Steinhauser, M.

    2017-12-01

    We combine the known asymptotic behaviour of the QCD perturbation series expansion, which relates the pole mass of a heavy quark to the MS ‾ mass, with the exact series coefficients up to the four-loop order to determine the ultimate uncertainty of the top-quark pole mass due to the renormalon divergence. We perform extensive tests of our procedure by varying the number of colours and flavours, as well as the scale of the strong coupling and the MS ‾ mass. Including an estimate of the internal bottom and charm quark mass effect, we conclude that this uncertainty is around 110 MeV. We further estimate the additional contribution to the mass relation from the five-loop correction and beyond to be around 300 MeV.

  20. Multiple (Two) Met Bel 601 In Series Ultimate Vacuum Testing

    Energy Technology Data Exchange (ETDEWEB)

    Restivo, M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-09-30

    SRNL Environmental and Chemical Process Technology (E&CPT) was requested to perform testing of vacuum pumps per a verbal request from the Customer, SRNL Hydrogen Processing Technology. Tritium Operations is currently having difficulties procuring the Normetex™® Model 15 m3/hr (9 CFM) vacuum pump (formerly Normetex Pompes, now EumecaSARL). One possible solution proposed by Hydrogen Processing Technology personnel is to use two Senior Aerospace Metal Bellows MB-601 vacuum pumps piped with the heads in series, and the pumps in series (Figure 1 below). This memorandum documents the ultimate vacuum testing that was performed to determine if this concept was a viable alternate vacuum pump strategy. This testing dovetails with previous pump evaluations documented in references 1 and 2.

  1. Ultimate Drivers and Proximate Correlates of Polyandry in Predatory Mites.

    Directory of Open Access Journals (Sweden)

    Peter Schausberger

    Full Text Available Polyandry is more widespread than anticipated from Bateman's principle but its ultimate (evolutionary causes and proximate (mechanistic correlates are more difficult to pinpoint than those of polygyny. Here, we combined mating experiments, quantification of reproductive traits and microsatellite genotyping to determine the fitness implications of polyandry in two predatory mite species, where males are highly polygynous (up to 45 fertilized females during life, whereas females range from monandry to various polyandry levels. The medium-level polyandrous (up to eight male mates possible Neoseiulus californicus received clear direct and indirect benefits: multiply mated females produced more offspring with higher survival chances over longer times than singly mated females. In contrast, singly and multiply mated females of the low-level polyandrous (commonly two male mates at maximum Phytoseiulus persimilis produced similar numbers of offspring having similar survival chances. In both species, multiple mating resulted in mixed offspring paternities, opening the chance for indirect fitness benefits such as enhanced genetic compatibility, complementarity and/or variability. However, the female re-mating likelihood and the paternity chance of non-first male mates were lower in P. persimilis than in N. californicus. Regarding proximate factors, in both species first mating duration and female re-mating likelihood were negatively correlated. Based on occasional fertilization failure of first male mates in P. persimilis, and mixed offspring paternities in both species, we argue that fertilization assurance and the chance to gain indirect fitness benefits are the ultimate drivers of polyandry in P. persimilis, whereas those of N. californicus are higher offspring numbers coupled with enhanced offspring viability and possibly other indirect fitness benefits. Overall, the adaptive significance and proximate events well reflected the polyandry levels. Our

  2. Ultimate Drivers and Proximate Correlates of Polyandry in Predatory Mites.

    Science.gov (United States)

    Schausberger, Peter; Patiño-Ruiz, J David; Osakabe, Masahiro; Murata, Yasumasa; Sugimoto, Naoya; Uesugi, Ryuji; Walzer, Andreas

    2016-01-01

    Polyandry is more widespread than anticipated from Bateman's principle but its ultimate (evolutionary) causes and proximate (mechanistic) correlates are more difficult to pinpoint than those of polygyny. Here, we combined mating experiments, quantification of reproductive traits and microsatellite genotyping to determine the fitness implications of polyandry in two predatory mite species, where males are highly polygynous (up to 45 fertilized females during life), whereas females range from monandry to various polyandry levels. The medium-level polyandrous (up to eight male mates possible) Neoseiulus californicus received clear direct and indirect benefits: multiply mated females produced more offspring with higher survival chances over longer times than singly mated females. In contrast, singly and multiply mated females of the low-level polyandrous (commonly two male mates at maximum) Phytoseiulus persimilis produced similar numbers of offspring having similar survival chances. In both species, multiple mating resulted in mixed offspring paternities, opening the chance for indirect fitness benefits such as enhanced genetic compatibility, complementarity and/or variability. However, the female re-mating likelihood and the paternity chance of non-first male mates were lower in P. persimilis than in N. californicus. Regarding proximate factors, in both species first mating duration and female re-mating likelihood were negatively correlated. Based on occasional fertilization failure of first male mates in P. persimilis, and mixed offspring paternities in both species, we argue that fertilization assurance and the chance to gain indirect fitness benefits are the ultimate drivers of polyandry in P. persimilis, whereas those of N. californicus are higher offspring numbers coupled with enhanced offspring viability and possibly other indirect fitness benefits. Overall, the adaptive significance and proximate events well reflected the polyandry levels. Our study provides a

  3. The optimum decision rules for the oddity task

    NARCIS (Netherlands)

    Versfeld, N.J.; Dai, H.; Green, D.M.

    1996-01-01

    This paper presents the optimum decision rule for an m-interval oddity task in which m-1 intervals contain the same signal and one is different or odd. The optimum decision rule depends on the degree of correlation among observations. The present approach unifies the different strategies that occur

  4. Optimum mobility’ facelift. Part 2 – the technique

    OpenAIRE

    Fanous, Nabil; Karsan, Naznin; Zakhary, Kristina; Tawile, Carolyne

    2006-01-01

    In the first of this two-part article on the ‘optimum mobility’ facelift, facial tissue mobility was analyzed, and three theories or mechanisms emerged: ‘intrinsic mobility’, ‘surgically induced mobility’ and ‘optimum mobility points’.

  5. Optimum material gradient composition for the functionally graded ...

    African Journals Online (AJOL)

    This study investigates the relation between the material gradient properties and the optimum sensing/actuation design of the functionally graded piezoelectric beams. Three-dimensional (3D) finite element analysis has been employed for the prediction of an optimum composition profile in these types of sensors and ...

  6. Optimum unambiguous discrimination of linearly independent pure state

    DEFF Research Database (Denmark)

    Pang, Shengshi; Wu, Shengjun

    2009-01-01

    be satisfied by the optimum solution in different situations. We also provide the detailed steps to find the optimum measurement strategy. The method and results we obtain are given a geometrical illustration with a numerical example. Furthermore, using these equations, we derive a formula which shows a clear...

  7. Defining Quantum Control Flow

    OpenAIRE

    Ying, Mingsheng; Yu, Nengkun; Feng, Yuan

    2012-01-01

    A remarkable difference between quantum and classical programs is that the control flow of the former can be either classical or quantum. One of the key issues in the theory of quantum programming languages is defining and understanding quantum control flow. A functional language with quantum control flow was defined by Altenkirch and Grattage [\\textit{Proc. LICS'05}, pp. 249-258]. This paper extends their work, and we introduce a general quantum control structure by defining three new quantu...

  8. Can play be defined?

    DEFF Research Database (Denmark)

    Eichberg, Henning

    2015-01-01

    Can play be defined? There is reason to raise critical questions about the established academic demand that at phenomenon – also in humanist studies – should first of all be defined, i.e. de-lineated and by neat lines limited to a “little box” that can be handled. The following chapter develops....... Human beings can very well understand play – or whatever phenomenon in human life – without defining it....

  9. Ultimate resources of drinking water in the event of a major pollution crisis: the role of bottled water

    International Nuclear Information System (INIS)

    Collin, J.J.; Comte, J.P.; Daum, J.R.; Lopoukhine, M.; Mesny, M.

    1995-01-01

    In the event of a serious and widespread pollution incident - on the level of the ''Chernobyl cloud'' - most of the drinking water resources in France could be contaminated : surface water immediately, ground water in a few days... or a few months. Therefore on the initiative of the Ministry of the Environment's Director for Defence, a study has been initiated as to what might be qualified as ''final emergency resources''. An inventory and map of protected resources have been prepared. In this context it seems reasonable to show bottled water as a resource meeting the necessary protection criteria. However it seems that these criteria are not all, nor always, relevant for defining a ''ultimate emergency resource'' not contaminated by a major incident. This article outlines a typology of situations and defines the main criteria necessary for bottled water to be able to constitute an ultimate resource

  10. Efficiency Of Different Teaching Models In Teaching Of Frisbee Ultimate

    Directory of Open Access Journals (Sweden)

    Žuffová Zuzana

    2015-05-01

    Full Text Available The aim of the study was to verify the efficiency of two frisbee ultimate teaching models at 8-year grammar schools relative to age. In the experimental group was used a game based model (Teaching Games for Understanding and in the control group the traditional model based on teaching techniques. 6 groups of female students took part in experiment: experimental group 1 (n=10, age=11.6, experimental group 2 (n=12, age=13.8, experimental group 3 (n=14, age =15.8, control group 1 (n=11, age =11.7, control group 2 (n=10, age =13.8 and control group 3 (n=9, age =15.8. Efficiency of the teaching models was evaluated based of game performance and special knowledge results. Game performance was evaluated by the method of game performance assessment based on GPAI (Game Performance Assessment Instrument through video record. To verify level of knowledge, we used a knowledge test, which consisted of questions related to the rules and tactics knowledge of frisbee ultimate. To perform statistical evaluation Mann-Whitney U-test was used. Game performance assessment and knowledge level indicated higher efficiency of TGfU in general, but mostly statistically insignificant. Experimental groups 1 and 2 were significantly better in the indicator that evaluates tactical aspect of game performance - decision making (p<0.05. Experimental group 3 was better in the indicator that evaluates skill execution - disc catching. The results showed that the students of the classes taught by game based model reached partially better game performance in general. Experimental groups achieved from 79.17 % to 80 % of correct answers relating to the rules and from 75 % to 87.5 % of correct answers relating to the tactical knowledge in the knowledge test. Control groups achieved from 57.69 % to 72.22 % of correct answers relating to the rules and from 51.92 % to 72.22 % of correct answers relating to the tactical knowledge in the knowledge test.

  11. Supersymmetry : the ultimate hierarchy of matter? Exhibition LEPFest 2000

    CERN Multimedia

    2000-01-01

    The concept of "Supersymmetry", SUSY for short, promises a solution to the 'hierarchy' problem: the mystery of the enormous ratio between the electroweak scale (at 100-300 GeV), defined by the masses of the W and Z particles, and possibly the Higgs particle, and the Planck scale (10 19 GeV), when gravitational effects become comparable to the other forces.

  12. Process Inherent Ultimate Safety (PIUS) reactor evaluation study: Final report

    International Nuclear Information System (INIS)

    1987-02-01

    This report presents the results of an independent study by United Engineers and Constructors (UNITED) of the SECURE-P Process Inherent Ultimate Safety (PIUS) Reactor Concept which is presently under development by the Swedish light water reactor vendor ASEA-ATOM of Vasteras, Sweden. This study was performed to investigate whether there is any realistic basis for believing that the PIUS reactor could be a viable competitor in the US energy market in the future. Assessments were limited to the technical, economic and licensing aspects of PIUS. Socio-political issues, while certainly important in answering this question, are so broad and elusive that it was considered that addressing them with the limited perspective of one small group from one company would be of questionable value and likely be misleading. Socio-political issues aside, the key issue is economics. For this reason, the specific objectives of this study were to determine if the estimated PIUS plant cost will be competitive in the US market and to identify and evaluate the technical and licensing risks that might make PIUS uneconomical or otherwise unacceptable

  13. ZIO: The Ultimate Linux I/O Framework

    CERN Document Server

    Gonzalez Cobas, J D; Rubini, A; Nellaga, S; Vaga, F

    2014-01-01

    ZIO (with Z standing for “The Ultimate I/O” Framework) was developed for CERN with the specific needs of physics labs in mind, which are poorly addressed in the mainstream Linux kernel. ZIO provides a framework for industrial, high-bandwith, high-channel count I/O device drivers (digitizers, function generators, timing devices like TDCs) with performance, generality and scalability as design goals. Among its features, it offers abstractions for • both input and output channels, and channel sets • run-time selection of trigger types • run-time selection of buffer types • sysfs-based configuration • char devices for data and metadata • a socket interface (PF ZIO) as alternative to char devices In this paper, we discuss the design and implementation of ZIO, and describe representative cases of driver development for typical and exotic applications: drivers for the FMC (FPGAMezzanine Card, see [1]) boards developed at CERN like the FMC ADC 100Msps digitizer, FMC TDC timestamp counter, and FMC DEL ...

  14. Episodic foresight and anxiety: Proximate and ultimate perspectives.

    Science.gov (United States)

    Miloyan, Beyon; Bulley, Adam; Suddendorf, Thomas

    2016-03-01

    In this paper, we examine the relationship between episodic foresight and anxiety from an evolutionary perspective, proposing that together they confer an advantage for modifying present moment decision-making and behaviour in the light of potential future threats to fitness. We review the body of literature on the role of episodic foresight in anxiety, from both proximate and ultimate perspectives. We propose that anxious feelings associated with episodic simulation of possible threat-related future events serve to imbue these simulations with motivational currency. Episodic and semantic details of a future threat may be insufficient for motivating its avoidance, but anxiety associated with a simulation can provoke adaptive threat management. As such, we detail how anxiety triggered by a self-generated, threat-related future simulation prepares the individual to manage that threat (in terms of its likelihood and/or consequences) over greater temporal distances than observed in other animals. We then outline how anxiety subtypes may represent specific mechanisms for predicting and managing particular classes of fitness threats. This approach offers an inroad for understanding the nature of characteristic future thinking patterns in anxiety disorders and serves to illustrate the adaptive function of the mechanism from which clinical anxiety deviates. © 2015 The British Psychological Society.

  15. Yield, utilization, storage and ultimate storage of depleted uranium

    International Nuclear Information System (INIS)

    Aumueller, L.; Hermann, J.

    1977-11-01

    More than 80% of the uranium leaving uranium enrichment plants is depleted to a residual content of about 0,25% U 235. Due to the present ineconomical further depletion to the technically possible residual content of 0,1% U 235, the so-called 'tails' are first of all stored. The quantity of stored depleted uranium in the FRG should be about 100.000 t by the year 2000. It represents a strategic reserve for future energy supply regardless of profitableness. The study analysis the conceivable possible uses for the tails quantity considered. These are, besides further depletion whose profitableness is considered, also the use as breeder material in breeder reactors and the use in the non-nuclear field. The main part of the study deals with the various storage possibilities of the depleted uranium in oxidic or fluoride form. A comparison of costs of alternative storage concepts showed a clear advantage for the storage of UF 6 in 48 inch containers already in use. The conceivable accidents in storing are analyzed and measures to reduce the consequences are discussed. Finally, the problems of ultimate storage for the remaining waste after further depletion or use are investigated and the costs arising here are also estimated. (RB) [de

  16. Optimized molten salt receivers for ultimate trough solar fields

    Science.gov (United States)

    Riffelmann, Klaus-J.; Richert, Timo; Kuckelkorn, Thomas

    2016-05-01

    Today parabolic trough collectors are the most successful concentrating solar power (CSP) technology. For the next development step new systems with increased operation temperature and new heat transfer fluids (HTF) are currently developed. Although the first power tower projects have successfully been realized, up to now there is no evidence of an all-dominant economic or technical advantage of power tower or parabolic trough. The development of parabolic trough technology towards higher performance and significant cost reduction have led to significant improvements in competitiveness. The use of molten salt instead of synthetic oil as heat transfer fluid will bring down the levelized costs of electricity (LCOE) even further while providing dispatchable energy with high capacity factors. FLABEG has developed the Ultimate TroughTM (UT) collector, jointly with sbp Sonne GmbH and supported by public funds. Due to its validated high optical accuracy, the collector is very suitable to operate efficiently at elevated temperatures up to 550 °C. SCHOTT will drive the key-innovations by introducing the 4th generation solar receiver that addresses the most significant performance and cost improvement measures. The new receivers have been completely redesigned to provide a product platform that is ready for high temperature operation up to 550 °C. Moreover distinct product features have been introduced to reduce costs and risks in solar field assembly and installation. The increased material and design challenges incurred with the high temperature operation have been reflected in sophisticated qualification and validation procedures.

  17. Accounting conservatism,ultimate ownership and investment efficiency

    Institute of Scientific and Technical Information of China (English)

    Xiaodong Xu; Xia Wang; Nina Han

    2012-01-01

    Purpose-The purpose of this paper is to analyze and examine the role of accounting conservatism on firm investment behavior in China.Design/methodology/approach-By combining a developed theoretical framework and empirical study,this paper examines the impacts of accounting conservatism on firm investment.The sample and data are all collected from Wind and CAMAR databases.Findings-The paper finds that the association between accounting conservatism and capital expenditure is significantly positive when inside capital is not enough to use for investment,suggesting that conservatism can expend the level of investment by decreasing information asymmetry and cost of capital;however,the association between accounting conservatism and capital expenditure is significantly negative when inside capital is enough to use for investment,suggesting that conservatism can curtail the level of investment by mitigating the interest conflicts between management and outside shareholders and decreasing agency costs.Additionally,the paper finds that the severity of information asymmetry and agency problem affects the role of accounting conservatism on firm investment behaviour,and the association between accounting conservatism and capital expenditure is weaker for firms with ultimate ownership controller as local government or individuals.Originality/value-This is the first paper to analyze and examine the impacts of accounting conservatism on firm investment in China directly.The findings are also useful to explain the awkward predicament found by prior literature.

  18. Ultimate storage of radioactive wastes annual report, 1973

    International Nuclear Information System (INIS)

    The present report is a cooperative effort by the Company for Radiation and Environmental Research, Munich, and the Company for Nuclear Research, Karlsruhe, and provides a survey of work carried out during 1973 in the area of ultimate storage of radioactive wastes. Mining and construction works which were carried out in the Asse Salt Mine near Remlingen both underground as well as above the ground and which were used for repair, maintenance and expansion of the operation consistent with its future tasks are reported. The storage of low-level wastes at the 750 m level and also the test-oriented storage of medium-level waste materials at the 490 m level were carried out within the reporting period. Shielded storage casks S7V developed by the GfK were used for the first time in September for transporting 200 l iron-hooped drums filled with medium-level radioactive wastes to Asse, each shipment always containing seven drums. With two round-trips a week taking place between the Nuclear Research Center, Karlsruhe and the Asse II shaft installation, 14 drums were brought each week so that, by the end of the year, the quantity in storage amounted to a total of 233 drums. Further information is provided concerning the present status of research work in the fields of oromechanics, geology and hydrology as well as other findings. Further, storage techniques are discussed which are presently in the planning stage

  19. Thermal performance measurements on ultimate heat sinks--cooling ponds

    International Nuclear Information System (INIS)

    Hadlock, R.K.; Abbey, O.B.

    1977-12-01

    The primary objective of the studies described is to obtain the requisite data, with respect to modeling requirements, to characterize thermal performance of heat sinks for nuclear facilities existing at elevated water temperatures in result of experiencing a genuinely large heat load and responding to meteorological influence. The data should reflect thermal performance for combinations leading to worst-case meteorological influence. A geothermal water retention basin has been chosen as the site for the first measurement program and data have been obtained in the first of several experiments scheduled to be performed there. These data illustrate the thermal and water budgets during episodes of cooling from an initially high pond water bulk temperature. Monitoring proceeded while the pond experienced only meteorological and seepage influence. The data are discussed and are presented as a data volume which may be used for calculation purposes. Suggestions for future measurement programs are stated with the intent to maintain and improve relevance to nuclear ultimate heat sinks while continuing to examine the performance of the analog geothermal pond. It is further suggested that the geothermal pond, with some modification, may be a suitable site for spray pond measurements

  20. Exploring Ultimate Water Capillary Evaporation in Nanoscale Conduits.

    Science.gov (United States)

    Li, Yinxiao; Alibakhshi, Mohammad Amin; Zhao, Yihong; Duan, Chuanhua

    2017-08-09

    Capillary evaporation in nanoscale conduits is an efficient heat/mass transfer strategy that has been widely utilized by both nature and mankind. Despite its broad impact, the ultimate transport limits of capillary evaporation in nanoscale conduits, governed by the evaporation/condensation kinetics at the liquid-vapor interface, have remained poorly understood. Here we report experimental study of the kinetic limits of water capillary evaporation in two dimensional nanochannels using a novel hybrid channel design. Our results show that the kinetic-limited evaporation fluxes break down the limits predicated by the classical Hertz-Knudsen equation by an order of magnitude, reaching values up to 37.5 mm/s with corresponding heat fluxes up to 8500 W/cm 2 . The measured evaporation flux increases with decreasing channel height and relative humidity but decreases as the channel temperature decreases. Our findings have implications for further understanding evaporation at the nanoscale and developing capillary evaporation-based technologies for both energy- and bio-related applications.

  1. Investigation of earthquake factor for optimum tuned mass dampers

    Science.gov (United States)

    Nigdeli, Sinan Melih; Bekdaş, Gebrail

    2012-09-01

    In this study the optimum parameters of tuned mass dampers (TMD) are investigated under earthquake excitations. An optimization strategy was carried out by using the Harmony Search (HS) algorithm. HS is a metaheuristic method which is inspired from the nature of musical performances. In addition to the HS algorithm, the results of the optimization objective are compared with the results of the other documented method and the corresponding results are eliminated. In that case, the best optimum results are obtained. During the optimization, the optimum TMD parameters were searched for single degree of freedom (SDOF) structure models with different periods. The optimization was done for different earthquakes separately and the results were compared.

  2. Comparison of Efficacy and Tolerance of Automatic Continuous Positive Airway Pressure Devices With the Optimum Continuous Positive Airway Pressure.

    Science.gov (United States)

    Tommi, George; Aronow, Wilbert S; Sheehan, John C; McCleay, Matthew T; Meyers, Patrick G

    Patients diagnosed with obstructive sleep apnea syndrome were randomly placed on automatic continuous positive airway pressure (ACPAP) for 2 hours followed by manual titration for the rest of the night. One hundred sixty-one patients entered the study, with at least 50 patients titrated with each of 3 ACPAP devices. The optimum continuous positive airway pressure (CPAP) was defined as the lowest pressure with an apnea-hypoxia index of ≤5/hr, which ranged from 4 cm to 18 cm. Success with ACPAP was approximately 60%-80% when the optimum CPAP was 4-6 cm but fell to below 30% if the optimum CPAP was ≥8 cm (P = 0.001). Average ACPAP ranged from 2 to 10 cm below the optimum level if the optimum CPAP was ≥8 cm. Patients who responded to a low CPAP but deteriorated on higher pressures failed to respond to any of the automatic devices. We recommend that CPAP titration be performed manually before initiation of ACPAP in patients with obstructive sleep apnea. The basal pressure for ACPAP should be the optimum pressure obtained by manual titration. Limits on the upper level of ACPAP may be necessary for patients who deteriorate on higher positive pressures.

  3. Defining Overweight and Obesity

    Science.gov (United States)

    ... Micronutrient Malnutrition State and Local Programs Defining Adult Overweight and Obesity Recommend on Facebook Tweet Share Compartir ... weight for a given height is described as overweight or obese. Body Mass Index, or BMI, is ...

  4. Drinking Levels Defined

    Science.gov (United States)

    ... of Alcohol Consumption Alcohol's Effects on the Body Alcohol Use Disorder Fetal Alcohol Exposure Support & Treatment Alcohol Policy Special ... Definition of Drinking at Low Risk for Developing Alcohol Use Disorder (AUD): For women, low-risk drinking is defined ...

  5. Optimum Temperature and Thermal Stability of Crude Polyphenol ...

    African Journals Online (AJOL)

    The optimum temperature was found to be 300C for the enzyme extracted from guava, ... processing industries because during the processing ... enhance the brown colour produced (Valero et al., ... considerable economic and nutritional loss.

  6. Performance characteristics of aerodynamically optimum turbines for wind energy generators

    Science.gov (United States)

    Rohrbach, C.; Worobel, R.

    1975-01-01

    This paper presents a brief discussion of the aerodynamic methodology for wind energy generator turbines, an approach to the design of aerodynamically optimum wind turbines covering a broad range of design parameters, some insight on the effect on performance of nonoptimum blade shapes which may represent lower fabrication costs, the annual wind turbine energy for a family of optimum wind turbines, and areas of needed research. On the basis of the investigation, it is concluded that optimum wind turbines show high performance over a wide range of design velocity ratios; that structural requirements impose constraints on blade geometry; that variable pitch wind turbines provide excellent power regulation and that annual energy output is insensitive to design rpm and solidity of optimum wind turbines.

  7. Optimum strategies for nuclear energy system development (method of synthesis)

    International Nuclear Information System (INIS)

    Belenky, V.Z.

    1983-01-01

    The problem of optimum long-term development of the nuclear energy system is considered. The optimum strategies (i.e. minimum total uranium consumption) for the transition phase leading to a stationary regime of development are found. For this purpose the author has elaborated a new method of solving linear problems of optimal control which can include jumps in trajectories. The method gives a possibility to fulfil a total synthesis of optimum strategies. A key characteristic of the problem is the productivity function of the nuclear energy system which connects technological system parameters with its growth rate. There are only two types of optimum strategies, according to an increasing or decreasing productivity function. Both cases are illustrated with numerical examples. (orig.) [de

  8. Experimental validation of optimum resistance moment of concrete ...

    African Journals Online (AJOL)

    Experimental validation of optimum resistance moment of concrete slabs reinforced ... other solutions to combat corrosion problems in steel reinforced concrete. ... Eight specimens of two-way spanning slabs reinforced with CFRP bars were ...

  9. Defining Documentary Film

    DEFF Research Database (Denmark)

    Juel, Henrik

    2006-01-01

    A discussion of various attemts at defining documentary film regarding form, content, truth, stile, genre or reception - and a propoposal of a positive list of essential, but non-exclusive characteristica of documentary film......A discussion of various attemts at defining documentary film regarding form, content, truth, stile, genre or reception - and a propoposal of a positive list of essential, but non-exclusive characteristica of documentary film...

  10. Optimum filters for narrow-band frequency modulation.

    Science.gov (United States)

    Shelton, R. D.

    1972-01-01

    The results of a computer search for the optimum type of bandpass filter for low-index angle-modulated signals are reported. The bandpass filters are discussed in terms of their low-pass prototypes. Only filter functions with constant numerators are considered. The pole locations for the optimum filters of several cases are shown in a table. The results are fairly independent of modulation index and bandwidth.

  11. Ultimate strength of a large wind turbine blade

    Energy Technology Data Exchange (ETDEWEB)

    Moelholt Jensen, Find

    2008-05-15

    of the profile, also called 'local deformations', to verify a more complex response than that of a Bernoulli-Euler Beam. A large number of mechanical displacement sensors and strain gauges were mounted inside and outside the structure. These measurements further proved highly useful when validating Finite Element based analysis and failure mechanisms should be decided. Finally, comparisons of the ultimate failure loads observed in the full-scale tests are presented and conclusions are drawn based on the mechanisms found. (au)

  12. Ultimate resistance of a reinforced concrete foundation under impulsive loading

    International Nuclear Information System (INIS)

    Aquaro, D.; Forasassi, G.; Marconi, M.

    2003-01-01

    The impact of a spent nuclear fuel cask against a reinforced concrete slab of a temporary repository for spent nuclear fuel is numerically analysed. The analysis considers accidental events in which a spent nuclear fuel cask would drop against the floor of a repository during lifting operations. Two types of solutions have been taken into account: a simple reinforced concrete structure and a structure provided with a 40 mm thick steel liner on the impacted surface, connected to a 1600 mm thick concrete bed. The model is assumed to be axisymmetric and positioned on an elastic ground (Winkler model). The concrete has been simulated as: elastic perfectly plastic under compressive stresses limited by a crushing strain; elastic linear under tensile stresses until a cracking stress value and a following decrease of stress characterized by a constant or variable softening modulus; limited ability to resist at shear stresses after cracking characterized by a shear retention factor. The steel of the reinforcement bars and of the cask has been simulated as an elastic perfectly plastic material. Several numerical simulations have been performed in order to determine the influence, on the ultimate resistance of the structure under examination, of the steel liner, of some characteristic parameters of concrete (as the softening module and the shear retention factor) and of the Winkler coefficient values, simulating the elastic behaviour of the ground. The obtained results demonstrate that a steel liner produces a lower stress in the concrete as well as in the reinforcement but the bed is still subjected to the cracking phenomenon throughout its entire width although the crushing is localized to only a few elements near the impact zone. The use of a more complex constitutive equation for the concrete considering the shear retention factor and the softening module has given results which do not differ greatly from those related to a more simplified model. A different degree of

  13. Optimum design of dual pressure heat recovery steam generator using non-dimensional parameters based on thermodynamic and thermoeconomic approaches

    International Nuclear Information System (INIS)

    Naemi, Sanaz; Saffar-Avval, Majid; Behboodi Kalhori, Sahand; Mansoori, Zohreh

    2013-01-01

    The thermodynamic and thermoeconomic analyses are investigated to achieve the optimum operating parameters of a dual pressure heat recovery steam generator (HRSG), coupled with a heavy duty gas turbine. In this regard, the thermodynamic objective function including the exergy waste and the exergy destruction, is defined in such a way to find the optimum pinch point, and consequently to minimize the objective function by using non-dimensional operating parameters. The results indicated that, the optimum pinch point from thermodynamic viewpoint is 2.5 °C and 2.1 °C for HRSGs with live steam at 75 bar and 90 bar respectively. Since thermodynamic analysis is not able to consider economic factors, another objective function including annualized installation cost and annual cost of irreversibilities is proposed. To find the irreversibility cost, electricity price and also fuel price are considered independently. The optimum pinch point from thermoeconomic viewpoint on basis of electricity price is 20.6 °C (75 bar) and 19.2 °C (90 bar), whereas according to the fuel price it is 25.4 °C and 23.7 °C. Finally, an extensive sensitivity analysis is performed to compare optimum pinch point for different electricity and fuel prices. -- Highlights: ► Presenting thermodynamic and thermoeconomic optimization of a heat recovery steam generator. ► Defining an objective function consists of exergy waste and exergy destruction. ► Defining an objective function including capital cost and cost of irreversibilities. ► Obtaining the optimized operating parameters of a dual pressure heat recovery boiler. ► Computing the optimum pinch point using non-dimensional operating parameters

  14. Definably compact groups definable in real closed fields. I

    OpenAIRE

    Barriga, Eliana

    2017-01-01

    We study definably compact definably connected groups definable in a sufficiently saturated real closed field $R$. We introduce the notion of group-generic point for $\\bigvee$-definable groups and show the existence of group-generic points for definably compact groups definable in a sufficiently saturated o-minimal expansion of a real closed field. We use this notion along with some properties of generic sets to prove that for every definably compact definably connected group $G$ definable in...

  15. Defining Game Mechanics

    DEFF Research Database (Denmark)

    Sicart (Vila), Miguel Angel

    2008-01-01

    This article defins game mechanics in relation to rules and challenges. Game mechanics are methods invoked by agents for interacting with the game world. I apply this definition to a comparative analysis of the games Rez, Every Extend Extra and Shadow of the Colossus that will show the relevance...... of a formal definition of game mechanics. Udgivelsesdato: Dec 2008...

  16. Modal Logics and Definability

    OpenAIRE

    Kuusisto, Antti

    2013-01-01

    In recent years, research into the mathematical foundations of modal logic has become increasingly popular. One of the main reasons for this is the fact that modal logic seems to adapt well to the requirements of a wide range of different fields of application. This paper is a summary of some of the author’s contributions to the understanding of modal definability theory.

  17. Software Defined Cyberinfrastructure

    Energy Technology Data Exchange (ETDEWEB)

    Foster, Ian; Blaiszik, Ben; Chard, Kyle; Chard, Ryan

    2017-07-17

    Within and across thousands of science labs, researchers and students struggle to manage data produced in experiments, simulations, and analyses. Largely manual research data lifecycle management processes mean that much time is wasted, research results are often irreproducible, and data sharing and reuse remain rare. In response, we propose a new approach to data lifecycle management in which researchers are empowered to define the actions to be performed at individual storage systems when data are created or modified: actions such as analysis, transformation, copying, and publication. We term this approach software-defined cyberinfrastructure because users can implement powerful data management policies by deploying rules to local storage systems, much as software-defined networking allows users to configure networks by deploying rules to switches.We argue that this approach can enable a new class of responsive distributed storage infrastructure that will accelerate research innovation by allowing any researcher to associate data workflows with data sources, whether local or remote, for such purposes as data ingest, characterization, indexing, and sharing. We report on early experiments with this approach in the context of experimental science, in which a simple if-trigger-then-action (IFTA) notation is used to define rules.

  18. Defining Abnormally Low Tenders

    DEFF Research Database (Denmark)

    Ølykke, Grith Skovgaard; Nyström, Johan

    2017-01-01

    The concept of an abnormally low tender is not defined in EU public procurement law. This article takes an interdisciplinary law and economics approach to examine a dataset consisting of Swedish and Danish judgments and verdicts concerning the concept of an abnormally low tender. The purpose...

  19. Software Defined Coded Networking

    DEFF Research Database (Denmark)

    Di Paola, Carla; Roetter, Daniel Enrique Lucani; Palazzo, Sergio

    2017-01-01

    the quality of each link and even across neighbouring links and using simulations to show that an additional reduction of packet transmission in the order of 40% is possible. Second, to advocate for the use of network coding (NC) jointly with software defined networking (SDN) providing an implementation...

  20. Defining depth of anesthesia.

    Science.gov (United States)

    Shafer, S L; Stanski, D R

    2008-01-01

    In this chapter, drawn largely from the synthesis of material that we first presented in the sixth edition of Miller's Anesthesia, Chap 31 (Stanski and Shafer 2005; used by permission of the publisher), we have defined anesthetic depth as the probability of non-response to stimulation, calibrated against the strength of the stimulus, the difficulty of suppressing the response, and the drug-induced probability of non-responsiveness at defined effect site concentrations. This definition requires measurement of multiple different stimuli and responses at well-defined drug concentrations. There is no one stimulus and response measurement that will capture depth of anesthesia in a clinically or scientifically meaningful manner. The "clinical art" of anesthesia requires calibration of these observations of stimuli and responses (verbal responses, movement, tachycardia) against the dose and concentration of anesthetic drugs used to reduce the probability of response, constantly adjusting the administered dose to achieve the desired anesthetic depth. In our definition of "depth of anesthesia" we define the need for two components to create the anesthetic state: hypnosis created with drugs such as propofol or the inhalational anesthetics and analgesia created with the opioids or nitrous oxide. We demonstrate the scientific evidence that profound degrees of hypnosis in the absence of analgesia will not prevent the hemodynamic responses to profoundly noxious stimuli. Also, profound degrees of analgesia do not guarantee unconsciousness. However, the combination of hypnosis and analgesia suppresses hemodynamic response to noxious stimuli and guarantees unconsciousness.

  1. Defining and classifying syncope

    NARCIS (Netherlands)

    Thijs, Roland D.; Wieling, Wouter; Kaufmann, Horacio; van Dijk, Gert

    2004-01-01

    There is no widely adopted definition or classification of syncope and related disorders. This lack of uniformity harms patient care, research, and medical education. In this article, syncope is defined as a form of transient loss of consciousness (TLOC) due to cerebral hypoperfusion. Differences

  2. 78 FR 69101 - Agency Information Collection Activities: Declaration of the Ultimate Consignee That Articles...

    Science.gov (United States)

    2013-11-18

    ... Activities: Declaration of the Ultimate Consignee That Articles Were Exported for Temporary Scientific or... the Declaration of the Ultimate Consignee that Articles were Exported for Temporary Scientific or...: Title: Declaration of the Ultimate Consignee that Articles were Exported for Temporary Scientific or...

  3. Parametric Investigation of Optimum Thermal Insulation Thickness for External Walls

    Directory of Open Access Journals (Sweden)

    Omer Kaynakli

    2011-06-01

    Full Text Available Numerous studies have estimated the optimum thickness of thermal insulation materials used in building walls for different climate conditions. The economic parameters (inflation rate, discount rate, lifetime and energy costs, the heating/cooling loads of the building, the wall structure and the properties of the insulation material all affect the optimum insulation thickness. This study focused on the investigation of these parameters that affect the optimum thermal insulation thickness for building walls. To determine the optimum thickness and payback period, an economic model based on life-cycle cost analysis was used. As a result, the optimum thermal insulation thickness increased with increasing the heating and cooling energy requirements, the lifetime of the building, the inflation rate, energy costs and thermal conductivity of insulation. However, the thickness decreased with increasing the discount rate, the insulation material cost, the total wall resistance, the coefficient of performance (COP of the cooling system and the solar radiation incident on a wall. In addition, the effects of these parameters on the total life-cycle cost, payback periods and energy savings were also investigated.

  4. Ultimate limit states of steel containment vessel under earthquake loadings

    International Nuclear Information System (INIS)

    Akiyama, Hiroshi; Yuhara, Tetsuo; Shimizu, Seiichi; Hayashi, Kazutoshi; Takahashi, Tadao.

    1986-01-01

    The limit state induced by buckling of cylindrical steel structures under earthquake loadings was investigated from the standpoint of energy concept. A number of the buckling test of cylindrical steel shell structures has been made, which showed that they have a stable load-displacement relation and adequate deformation capacities beyond the buckling. The authors are proposing that the energy input imparted by strong earthquakes to buckled structures and the deformation capacity in post-buckling are suitable indices for seismic resistance of the cylindrical steel shell structures because the buckling does not cause the structure immediately to collapse in the case of such repeated loading as earthquake motions. The purpose of this study is to investigate the energy input to buckled cylindrical steel structures with an increase in the intensity of earthquake motions. A series of nonlinear dynamic analyses were performed under various types of earthquake records by using a hysteresis loop, including buckling, which was derived from the buckling tests. The limit state could be defined as the state in which the deformation of and the energy input into buckled structures increase divergently when the intensity of the earthquake excitation exceeds a certain value. The results obtained in this paper are intended to be adopted to the limit state in the post-buckling region to evaluate the margin of safety against the buckling resistance of cylindrical steel structures under strong earthquake loadings. (author)

  5. PSA Update Procedures, an Ultimate Need for Living PSA

    International Nuclear Information System (INIS)

    Hegedus, D.

    1998-01-01

    Nuclear facilities by their complex nature, change with time. These changes can be both physical (plant modification, etc.), operational (enhanced procedures, etc.) and organizational. In addition, there are also changes in our understanding of the plant, due to operational experience, data collection, technology enhancements, etc. Therefore, it is imperative that PSA model must be frequently up-dated or modified to reflect these changes. Over the last ten years. these has been a remarkable growth of the use of Probabilistic Safety Assessments (PSAs). The most rapidly growing area of the PSA Applications is their use to support operational decision-making. Many of these applications are characterized by the potential for not only improving the safety level but also for providing guidance on the optimal use of resources and reducing regulatory burden. To enable a wider use of the PSA model as a tool for safety activities it is essential to maintain the model in a controlled state. Moreover, to fulfill requirements for L iving PSA , the PSA model has to be constantly updated and/or monitored to reflect the current plant configuration. It should be noted that the PSA model should not only represent the plant design but should also represent the operational and emergency procedures. To keep the PSA model up-to-date several issues should be clearly defined including: - Responsibility should be divided among the PSA group, - Procedures for implementing changes should be established, and - QA requirements/program should be established to assure documentation and reporting. (author)

  6. BOOK REVIEW: Seeking Ultimates. An Intuitive Guide to Physics

    Science.gov (United States)

    Brown, Neil

    2000-05-01

    Physics has the reputation of being a difficult and dry subject. Many books have been written in attempts to show that the difficulties are not insurmountable, even for the layman, and to convey some of the fascination it provides for those within it. In Seeking Ultimates Peter Landsberg avoids mathematics, the source of so many difficulties, entirely, and seeks to make physics comprehensible by what he terms intuition. He also emphasizes that there is almost no part of science that is completely understood; there are always areas of incompleteness and uncertainty, capable of providing exciting new results, and examples of this are highlighted throughout the book. After an introduction Landsberg starts with macroscopic phenomena for ease of understanding, though one might question whether the chosen topic of thermodynamics is ever going to be easy. Next he looks at microscopic effects, from atomic structure to the fundamental particles of the standard model and their interactions. There follow chapters on time and entropy, on chaos theory, on quantum mechanics and then cosmology. The final chapters look at physical constants (including the anthropic principle), whether physics has room for a creator God (the conclusion is that this is not the province of science), and some thoughts on science as a human activity. The chosen topics are those which have been important in the late twentieth century and remain important. Each chapter cites an eminent scientist as a `hero', though little is made of this. There are occasional historical notes, set in boxes, and a few short poems to leaven the text. What the book achieves is difficult to assess. Removing mathematics and adding a glossary of technical terms do not necessarily allow non-scientists to enjoy the text, as the publisher's note on the back cover suggests. The concepts can baffle the layman even more than the mathematics, and one of the most difficult of all physical concepts permeates so much of this book

  7. Confidence interval of intrinsic optimum temperature estimated using thermodynamic SSI model

    Institute of Scientific and Technical Information of China (English)

    Takaya Ikemoto; Issei Kurahashi; Pei-Jian Shi

    2013-01-01

    The intrinsic optimum temperature for the development of ectotherms is one of the most important factors not only for their physiological processes but also for ecological and evolutional processes.The Sharpe-Schoolfield-Ikemoto (SSI) model succeeded in defining the temperature that can thermodynamically meet the condition that at a particular temperature the probability of an active enzyme reaching its maximum activity is realized.Previously,an algorithm was developed by Ikemoto (Tropical malaria does not mean hot environments.Journal of Medical Entomology,45,963-969) to estimate model parameters,but that program was computationally very time consuming.Now,investigators can use the SSI model more easily because a full automatic computer program was designed by Shi et al.(A modified program for estimating the parameters of the SSI model.Environmental Entomology,40,462-469).However,the statistical significance of the point estimate of the intrinsic optimum temperature for each ectotherm has not yet been determined.Here,we provided a new method for calculating the confidence interval of the estimated intrinsic optimum temperature by modifying the approximate bootstrap confidence intervals method.For this purpose,it was necessary to develop a new program for a faster estimation of the parameters in the SSI model,which we have also done.

  8. Towards New Renewable Energy Policies in Urban Areas: the Re-Definition of Optimum Inclination of Photovoltaic Panels

    Directory of Open Access Journals (Sweden)

    Manfred Weissenbacher

    2015-12-01

    Full Text Available The optimum inclination and orientation of fixed photovoltaic (PV panels has long been defined in terms of maximizing the annual electricity yield per capacity installed according to the hemisphere and latitude where the PV system is located. Such optimum setup would thus also maximize the output per system cost, but it would not maximize the output per unit of available area, and it would not necessarily optimize the contribution of photovoltaic electricity vis-à-vis overall electricity demand patterns. This study seeks to draw the attention of policy-makers to the fact that incentivizing lower-than-optimum PV panel tilt angles can be an inexpensive strategy to substantially increase the renewable electricity yield in a given area. It also discusses how such strategy can be incorporated into an overall supply/demand grid management and renewable energy integration plan.

  9. Optimum Arrangement of Reactive Power Sources While Using Genetic Algori

    Directory of Open Access Journals (Sweden)

    A. M. Gashimov

    2010-01-01

    Full Text Available Reduction of total losses in distribution electricity supply network is considered as an important measure which serves for improvement of efficiency of electric power supply systems. This objective can be achieved by optimum distribution of reactive power sources in proper places of distribution electricity supply network. The proposed methodology is based on application of a genetic algorithm. Total expenses for installation of capacitor banks, their operation and also expenses related to electric power losses are considered as an efficiency function which is used for determination of places with optimum values of capacitor bank power. The methodology is the most efficient for selection of optimum places in the network where it is necessary to install capacitor banks with due account of their power control depending on a switched-on load value in the units.

  10. Optimum Combining for Rapidly Fading Channels in Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    Sonia Furman

    2003-10-01

    Full Text Available Research and technology in wireless communication systems such as radar and cellular networks have successfully implemented alternative design approaches that utilize antenna array techniques such as optimum combining, to mitigate the degradation effects of multipath in rapid fading channels. In ad hoc networks, these methods have not yet been exploited primarily due to the complexity inherent in the network's architecture. With the high demand for improved signal link quality, devices configured with omnidirectional antennas can no longer meet the growing need for link quality and spectrum efficiency. This study takes an empirical approach to determine an optimum combining antenna array based on 3 variants of interelement spacing. For rapid fading channels, the simulation results show that the performance in the network of devices retrofitted with our antenna arrays consistently exceeded those with an omnidirectional antenna. Further, with the optimum combiner, the performance increased by over 60% compared to that of an omnidirectional antenna in a rapid fading channel.

  11. Optimum detection for extracting maximum information from symmetric qubit sets

    International Nuclear Information System (INIS)

    Mizuno, Jun; Fujiwara, Mikio; Sasaki, Masahide; Akiba, Makoto; Kawanishi, Tetsuya; Barnett, Stephen M.

    2002-01-01

    We demonstrate a class of optimum detection strategies for extracting the maximum information from sets of equiprobable real symmetric qubit states of a single photon. These optimum strategies have been predicted by Sasaki et al. [Phys. Rev. A 59, 3325 (1999)]. The peculiar aspect is that the detections with at least three outputs suffice for optimum extraction of information regardless of the number of signal elements. The cases of ternary (or trine), quinary, and septenary polarization signals are studied where a standard von Neumann detection (a projection onto a binary orthogonal basis) fails to access the maximum information. Our experiments demonstrate that it is possible with present technologies to attain about 96% of the theoretical limit

  12. Defining Legal Moralism

    DEFF Research Database (Denmark)

    Thaysen, Jens Damgaard

    2015-01-01

    This paper discusses how legal moralism should be defined. It is argued that legal moralism should be defined as the position that “For any X, it is always a pro tanto reason for justifiably imposing legal regulation on X that X is morally wrong (where “morally wrong” is not conceptually equivalent...... to “harmful”)”. Furthermore, a distinction between six types of legal moralism is made. The six types are grouped according to whether they are concerned with the enforcement of positive or critical morality, and whether they are concerned with criminalising, legally restricting, or refraining from legally...... protecting morally wrong behaviour. This is interesting because not all types of legal moralism are equally vulnerable to the different critiques of legal moralism that have been put forth. Indeed, I show that some interesting types of legal moralism have not been criticised at all....

  13. Defining local food

    DEFF Research Database (Denmark)

    Eriksen, Safania Normann

    2013-01-01

    Despite evolving local food research, there is no consistent definition of “local food.” Various understandings are utilized, which have resulted in a diverse landscape of meaning. The main purpose of this paper is to examine how researchers within the local food systems literature define local...... food, and how these definitions can be used as a starting point to identify a new taxonomy of local food based on three domains of proximity....

  14. Determination of optimum oven cooking procedures for lean beef products

    OpenAIRE

    Rodas?Gonz?lez, Argenis; Larsen, Ivy L.; Uttaro, Bethany; Ju?rez, Manuel; Parslow, Joyce; Aalhus, Jennifer L.

    2015-01-01

    Abstract In order to determine optimum oven cooking procedures for lean beef, the effects of searing at 232 or 260?C for 0, 10, 20 or 30?min, and roasting at 160 or 135?C on semimembranosus (SM) and longissimus lumborum (LL) muscles were evaluated. In addition, the optimum determined cooking method (oven?seared for 10?min at 232?C and roasted at 135?C) was applied to SM roasts varying in weight from 0.5 to 2.5?kg. Mainly, SM muscles seared for 0 or 10?min at 232?C followed by roast at 135?C h...

  15. A first course in optimum design of yacht sails

    Science.gov (United States)

    Sugimoto, Takeshi

    1993-03-01

    The optimum sail geometry is analytically obtained for the case of maximizing the thrust under equality and inequality constraints on the lift and the heeling moment. A single mainsail is assumed to be set close-hauled in uniform wind and upright on the flat sea surface. The governing parameters are the mast height and the gap between the sail foot and the sea surface. The lifting line theory is applied to analyze the aerodynamic forces acting on a sail. The design method consists of the variational principle and a feasibility study. Almost triangular sails are found to be optimum. Their advantages are discussed.

  16. Generic Advertising Optimum Budget for Iran’s Milk Industry

    Directory of Open Access Journals (Sweden)

    H. Shahbazi

    2016-05-01

    Full Text Available Introduction One of the main targets of planners, decision makers and governments is increasing society health with promotion and production of suitable and healthy food. One of the basic commodities that have important role in satisfaction of required human food is milk. So, some part of government and producer healthy budget allocate to milk consumption promotion by using generic advertising. If effectiveness of advertising budget on profitability is more, producer will have more willing to spend for advertising. Determination of optimal generic advertising budget is one of important problem in managerial decision making in producing firm as well as increase in consumption and profit and decrease in wasting and non-optimality of budget. Materials and Methods: In this study, optimal generic advertising budget intensity index (advertising budget share of production cost was estimated under two different scenarios by using equilibrium replacement model. In equilibrium replacement model, producer surplus are maximized in respect to generic advertising in retail level. According to market where two levels of farm and processing before retail exist and there is trade in farm and retail level, we present different models. Fixed and variable proportion hypothesis is another one. Finally, eight relations are presented for determination of milk generic advertising optimum budget. So, we use data from several resources such as previous studies, national (Iran Static center and international institute (Fao formal data and own estimation. Because there are several estimations in previous studies, we identify some scenarios (in two general scenarios for calculation of milk generic advertising optimum budget. Results and Discussion: Estimation of milk generic advertising optimum budget in scenario 1 shows that in case of one market level, fixed supplies and no trade, optimum budget is 0.4672539 percent. In case of one market level and no trade, optimum

  17. Optimum position of isolators within erbium-doped fibers

    DEFF Research Database (Denmark)

    Lumholt, Ole; Schüsler, Kim; Bjarklev, Anders Overgaard

    1992-01-01

    An isolator is used as an amplified spontaneous emission suppressing component within an erbium-doped fiber. The optimum isolator placement is both experimentally and theoretically determined and found to be slightly dependent upon pump power. Improvements of 4 dB in gain and 2 dB in noise figure...... are measured for the optimum isolator location at 25% of the fiber length when the fiber is pumped with 60 mW of pump power at 1.48 μm...

  18. Tissue architecture: the ultimate regulator of breast epithelial function

    Energy Technology Data Exchange (ETDEWEB)

    Bissell, Mina J; Rizki, Aylin; Mian, Saira

    2003-10-20

    A problem in developmental biology that continues to take center stage is how higher organisms generate diverse tissues and organs given the same cellular genotype. In cell and tumor biology, the key question is not the production of form, but its preservation: how do tissues and organs maintain homeostasis, and how do cells within tissues lose or overcome these controls in cancer? Undoubtedly, mechanisms that maintain tissue specificity should share features with those employed to drive formation of the tissues. However, they are unlikely to be identical. At a simplistic level, developmental pathways may be thought of as a series of extremely rapid short-term events. Each new step depends on what came before, and the outcome is the organism itself at birth. All organs, with a few notable exceptions, such as the mammary gland and the brain, 'arrive' together and are complete when the organism is born. In mice and humans, these events occur in a mere 21 days and 9 months respectively. The stability of the differentiated state and the homeostasis of the organism, on the other hand, will last 40-110 times longer. How does the organism achieve this feat? How are tissues maintained? These questions also relate fundamentally to how tissues become malignant and, although not discussed here, to aging. While there is much literature on differentiation - loosely defined as the gain of a single or a series of functions - we know much less about the forces and the pathways that maintain organ morphology and function as a unit. This may be partly because it is difficult to study a tissue as a unit in vivo and there are few techniques that allow maintenance of organs in vitro long enough and in such a way as to make cell and molecular biology experiments possible. Techniques for culturing cells in three-dimensional gels (3D) as a surrogate for tissues, however, have been steadily improving and the method is now used by several laboratories. In this commentary we

  19. Determination of Optimum Moisture Content of Palm Nut Cracking ...

    African Journals Online (AJOL)

    USER

    ABSTRACT: After processing the palm fruit for oil, the nut is usually dried in order to loosen the kernel from the shell. The drying is necessary to enhance the release of whole kernel when the nut is cracked. A study was carried out to determine the optimum moisture content of nuts for high yield of whole kernels during ...

  20. Optimum tilt angle and orientation for solar collectors in Syria

    International Nuclear Information System (INIS)

    Skeiker, Kamal

    2009-01-01

    One of the important parameters that affect the performance of a solar collector is its tilt angle with the horizon. This is because of the variation of tilt angle changes the amount of solar radiation reaching the collector surface. A mathematical model was used for estimating the solar radiation on a tilted surface, and to determine the optimum tilt angle and orientation (surface azimuth angle) for the solar collector in the main Syrian zones, on a daily basis, as well as for a specific period. The optimum angle was computed by searching for the values for which the radiation on the collector surface is a maximum for a particular day or a specific period. The results reveal that changing the tilt angle 12 times in a year (i.e. using the monthly optimum tilt angle) maintains approximately the total amount of solar radiation near the maximum value that is found by changing the tilt angle daily to its optimum value. This achieves a yearly gain in solar radiation of approximately 30% more than the case of a solar collector fixed on a horizontal surface.

  1. Analytical Solution for Optimum Design of Furrow Irrigation Systems

    Science.gov (United States)

    Kiwan, M. E.

    1996-05-01

    An analytical solution for the optimum design of furrow irrigation systems is derived. The non-linear calculus optimization method is used to formulate a general form for designing the optimum system elements under circumstances of maximizing the water application efficiency of the system during irrigation. Different system bases and constraints are considered in the solution. A full irrigation water depth is considered to be achieved at the tail of the furrow line. The solution is based on neglecting the recession and depletion times after off-irrigation. This assumption is valid in the case of open-end (free gradient) furrow systems rather than closed-end (closed dike) systems. Illustrative examples for different systems are presented and the results are compared with the output obtained using an iterative numerical solution method. The final derived solution is expressed as a function of the furrow length ratio (the furrow length to the water travelling distance). The function of water travelling developed by Reddy et al. is considered for reaching the optimum solution. As practical results from the study, the optimum furrow elements for free gradient systems can be estimated to achieve the maximum application efficiency, i.e. furrow length, water inflow rate and cutoff irrigation time.

  2. Optimum position for wells producing at constant wellbore pressure

    Energy Technology Data Exchange (ETDEWEB)

    Camacho-Velazquez, R.; Rodriguez de la Garza, F. [Univ. Nacional Autonoma de Mexico, Mexico City (Mexico); Galindo-Nava, A. [Inst. Mexicanos del Petroleo, Mexico City (Mexico)]|[Univ. Nacional de Mexico, Mexico City (Mexico); Prats, M.

    1994-12-31

    This paper deals with the determination of the optimum position of several wells, producing at constant different wellbore pressures from a two-dimensional closed-boundary reservoirs, to maximize the cumulative production or the total flow rate. To achieve this objective they authors use an improved version of the analytical solution recently proposed by Rodriguez and Cinco-Ley and an optimization algorithm based on a quasi-Newton procedure with line search. At each iteration the algorithm approximates the negative of the objective function by a cuadratic relation derived from a Taylor series. The improvement of rodriguez and Cinco`s solution is attained in four ways. First, an approximation is obtained, which works better at earlier times (before the boundary dominated period starts) than the previous solution. Second, the infinite sums that are present in the solution are expressed in a condensed form, which is relevant for reducing the computer time when the optimization algorithm is used. Third, the solution is modified to take into account the possibility of having wells starting to produce at different times. This point allows them to deal with the problem of getting the optimum position for an infill drilling program. Last, the solution is extended to include the possibility of changing the value of wellbore pressure or being able to stimulate any of the wells at any time. When the wells are producing at different wellbore pressures it is found that the optimum position is a function of time, otherwise the optimum position is fixed.

  3. Optimum Onager: The Classical Mechanics of a Classical Siege Engine

    Science.gov (United States)

    Denny, Mark

    2009-01-01

    The onager is a throwing weapon of classical antiquity, familiar to both the ancient Greeks and Romans. Here we analyze the dynamics of onager operation and derive the optimum angle for launching a projectile to its maximum range. There is plenty of scope for further considerations about increasing onager range, and so by thinking about how this…

  4. The effects of physical and chemical changes on the optimum ...

    African Journals Online (AJOL)

    The aim of this study was to determine physical and chemical changes during fruit development and their relationship with optimum harvest maturity for Bacon, Fuerte and Zutano avocado cultivars grown under Dörtyol ecological condition. Fruits cv. Bacon, Fuerte and Zutano were obtained trees grafted on seedlings and ...

  5. Applied orthogonal experiment design for the optimum microwave ...

    African Journals Online (AJOL)

    An experiment on polysaccharides from Rhodiolae Radix (PRR) extraction was carried out using microwave-assisted extraction (MAE) method with an objective to establishing the optimum MAE conditions of PRR. Single factor experiments were performed to determine the appropriate range of extraction conditions, and the ...

  6. Optimum geometry for torque ripple minimization of switched reluctance motors

    NARCIS (Netherlands)

    Sahin, F.; Ertan, H.B.; Leblebicioglu, K.

    2000-01-01

    For switched reluctance motors, one of the major problems is torque ripple which causes increased undesirable acoustic noise and possibly speed ripple. This paper describes an approach to determine optimum magnetic circuit parameters to minimize low speed torque ripple for such motors. The

  7. METHODS FOR DETERMINATION OF THE OPTIMUM EXPLOSIVES IN DIFFERENT ROCKS

    Directory of Open Access Journals (Sweden)

    Josip Krsnik

    1989-12-01

    Full Text Available The most appropriate explosives required for blasting of the particular types of rocks were established by test blasting method with linear burden increase. By the same method the optimum magnitudes of deep-holes blasting were established (the paper is published in Croatian.

  8. Applicability Problem in Optimum Reinforced Concrete Structures Design

    Directory of Open Access Journals (Sweden)

    Ashara Assedeq

    2016-01-01

    Full Text Available Optimum reinforced concrete structures design is very complex problem, not only considering exactness of calculus but also because of questionable applicability of existing methods in practice. This paper presents the main theoretical mathematical and physical features of the problem formulation as well as the review and analysis of existing methods and solutions considering their exactness and applicability.

  9. Is there an optimum level for renewable energy?

    International Nuclear Information System (INIS)

    Moriarty, Patrick; Honnery, Damon

    2011-01-01

    Because continued heavy use of fossil fuel will lead to both global climate change and resource depletion of easily accessible fuels, many researchers advocate a rapid transition to renewable energy (RE) sources. In this paper we examine whether RE can provide anywhere near the levels of primary energy forecast by various official organisations in a business-as-usual world. We find that the energy costs of energy will rise in a non-linear manner as total annual primary RE output increases. In addition, increasing levels of RE will lead to increasing levels of ecosystem maintenance energy costs per unit of primary energy output. The result is that there is an optimum level of primary energy output, in the sense that the sustainable level of energy available to the economy is maximised at that level. We further argue that this optimum occurs at levels well below the energy consumption forecasts for a few decades hence. - Highlights: → We need to shift to renewable energy for climate change and fuel depletion reasons. → We examine whether renewable energy can provide the primary energy levels forecast. → The energy costs of energy rise non-linearly with renewable energy output. → There is thus an optimum level of primary energy output. → This optimum occurs at levels well below future official energy use forecasts.

  10. How stem defects affect the capability of optimum bucking method?

    Directory of Open Access Journals (Sweden)

    Abdullah Emin Akay

    2015-07-01

    Full Text Available In forest harvesting activities, computer-assisted optimum bucking method increases the economic value of harvested trees. The bucking decision highly depends on the log quality grades which mainly vary with the surface characteristics such as stem defects and form of the stems. In this study, the effects of stem defects on optimum bucking method was investigated by comparing bucking applications which were conducted during the logging operations in two different Brutian Pine (Pinus brutia Ten stands. In the applications, the first stand contained the stems with relatively more stem defects than that of the stems in the second stand. The average number of defects per log for sample trees in the first and the second stand was recorded as 3.64 and 2.70, respectively. The results indicated that optimum bucking method increased the average economic value of harvested trees by 15.45% and 8.26 % in the stands, respectively. Therefore, the computer-assisted optimum bucking method potentially provides better results than that of traditional bucking method especially for the harvested trees with more stem defects.

  11. Optimum length of finned pipe for waste heat recovery

    International Nuclear Information System (INIS)

    Soeylemez, M.S.

    2008-01-01

    A thermoeconomic feasibility analysis is presented yielding a simple algebraic optimization formula for estimating the optimum length of a finned pipe that is used for waste heat recovery. A simple economic optimization method is used in the present study by combining it with an integrated overall heat balance method based on fin effectiveness for calculating the maximum savings from a waste heat recovery system

  12. The Optimum Conditions of Foreign Languages in Primary Education

    Science.gov (United States)

    Giannikas, Christina Nicole

    2014-01-01

    The aim of the paper is to review the primary language learning situation in Europe and shed light on the benefits it carries. Early language learning is the biggest policy development in education and has developed in rapid speed over the past 30 years; this article considers the effects and advantages of the optimum condition of an early start,…

  13. Improved optimum condition for recovery and measurement of 210 ...

    African Journals Online (AJOL)

    The aim of this study was to determine the optimum conditions for deposition of 210Po and evaluate the accuracy and precision of the results for its determination in environmental samples. To improve the technique for measurement of polonium-210(210Po) in environmental samples. The optimization of five factors (volume ...

  14. Dietary energy level for optimum productivity and carcass ...

    African Journals Online (AJOL)

    user

    2013-08-05

    Aug 5, 2013 ... optimum weights at dietary energy levels of 13.81, 13.23, 13.43 and ... Tadelle & Ogle (2000) reported that energy requirement of ..... The authors would like to acknowledge the National Research Foundation (NRF) and VLIR ...

  15. Bud initiation and optimum harvest date in Brussels sprouts

    NARCIS (Netherlands)

    Everaarts, A.P.; Sukkel, W.

    1999-01-01

    For six cultivars of Brussels sprouts (Brassica oleracea var. gemmifera) with a decreasing degree of earliness, or optimum harvest date, the time of bud initiation was determined during two seasons. Fifty percent of the plants had initiated buds between 60 and 75 days after planting (DAP) in 1994

  16. Optimum dietary protein requirement of genetically male tilapia ...

    African Journals Online (AJOL)

    The study was conducted to investigate the optimum dietary protein level needed for growing genetically male tilapia, Oreochromis niloticus. Diets containing crude protein levels 40, 42.5, 45, 47.5 and 50% were formulated and tried in triplicates. Test diets were fed to 20 fish/1m3 floating hapa at 5% of fish body weight daily ...

  17. Optimum development temperature and duration for nuclear plate

    International Nuclear Information System (INIS)

    Nagoshi, Chieko.

    1975-01-01

    Sakura 100 μm thick nuclear plates have been employed to determine optimum temperature and duration of the Amidol developer for low energy protons (Ep 0 C were tried for periods of 15--35 min. For Ep 0 C and for development time less than 30 min. (auth.)

  18. Optimum workforce-size model using dynamic programming approach

    African Journals Online (AJOL)

    This paper presents an optimum workforce-size model which determines the minimum number of excess workers (overstaffing) as well as the minimum total recruitment cost during a specified planning horizon. The model is an extension of other existing dynamic programming models for manpower planning in the sense ...

  19. Dietary energy level for optimum productivity and carcass ...

    African Journals Online (AJOL)

    A study was conducted to determine dietary energy levels for optimum productivity and carcass characteristics of indigenous Venda chickens raised in closed confinement. Four dietary treatments were considered in the first phase (1 to 7 weeks) on two hundred day-old unsexed indigenous Venda chicks indicated as EVS1, ...

  20. Procedure for determining the optimum rate of increasing shaft depth

    Energy Technology Data Exchange (ETDEWEB)

    Durov, E.M.

    1983-03-01

    Presented is an economic analysis of increasing shaft depth during mine modernization. Investigations carried out by the Yuzhgiproshakht Institute are analyzed. The investigations are aimed at determining the optimum shaft sinking rate (the rate which reduces investment to the minimum). The following factors are considered: coal output of a mine (0.9, 1.2, 1.5 and 1.8 Mt/year), depth at which the new mining level is situated (600, 800, 1200, 1400 and 1600 m), four schemes of increasing depth of 2 central shafts (rock hoisting to ground surface, rock hoisting to the existing level, rock haulage to the developed level, rock haulage to the level being developed using a large diameter borehole drilled from the new level to the shaft bottom and enlarged from shaft bottom to the new level), shaft sinking rate (10, 20, 30, 40, 50 and 60 m/month), range of increasing shaft depth (the difference between depth of the shaft before and after increasing its depth by 100, 200, 300 and 400 m). Comparative evaluations show that the optimum shaft sinking rate depends on the scheme for rock hoisting (one of 4 analyzed), range of increasing shaft depth and gas content in coal seams. The optimum shaft sinking rate ranges from 20 to 40 m/month in coal mines with low methane content and from 20 to 30 m/month in gassy coal mines. The planned coal output of a mine does not influence the optimum shaft sinking rate.

  1. Deuterium–tritium catalytic reaction in fast ignition: Optimum ...

    Indian Academy of Sciences (India)

    proton beam, the corresponding optimum interval values are proton average energy 3 ... contributions, into the study of the ignition and burn dynamics in a fast ignition frame- ..... choice of proton beam energy would fall in 3 ≤ Ep ≤ 10 MeV.

  2. Optimum design for pipe-support allocation against seismic loading

    International Nuclear Information System (INIS)

    Hara, Fumio; Iwasaki, Akira

    1996-01-01

    This paper deals with the optimum design methodology of a piping system subjected to a seismic design loading to reduce its dynamic response by selecting the location of pipe supports and whereby reducing the number of pipe supports to be used. The author employs the Genetic Algorithm for obtaining a reasonably optimum solution of the pipe support location, support capacity and number of supports. The design condition specified by the support location, support capacity and the number of supports to be used is encored by an integer number string for each of the support allocation candidates and they prepare many strings for expressing various kinds of pipe-support allocation state. Corresponding to each string, the authors evaluate the seismic response of the piping system to the design seismic excitation and apply the Genetic Algorithm to select the next generation candidates of support allocation to improve the seismic design performance specified by a weighted linear combination of seismic response magnitude, support capacity and the number of supports needed. Continuing this selection process, they find a reasonably optimum solution to the seismic design problem. They examine the feasibility of this optimum design method by investigating the optimum solution for 5, 7 and 10 degree-of-freedom models of piping system, and find that this method can offer one a theoretically feasible solution to the problem. They will be, thus, liberated from the severe uncertainty of damping value when the pipe support guaranties the design capacity of damping. Finally, they discuss the usefulness of the Genetic Algorithm for the seismic design problem of piping systems and some sensitive points when it will be applied to actual design problems

  3. Defined contribution health benefits.

    Science.gov (United States)

    Fronstin, P

    2001-03-01

    This Issue Brief discusses the emerging issue of "defined contribution" (DC) health benefits. The term "defined contribution" is used to describe a wide variety of approaches to the provision of health benefits, all of which have in common a shift in the responsibility for payment and selection of health care services from employers to employees. DC health benefits often are mentioned in the context of enabling employers to control their outlay for health benefits by avoiding increases in health care costs. DC health benefits may also shift responsibility for choosing a health plan and the associated risks of choosing a plan from employers to employees. There are three primary reasons why some employers currently are considering some sort of DC approach. First, they are once again looking for ways to keep their health care cost increases in line with overall inflation. Second, some employers are concerned that the public "backlash" against managed care will result in new legislation, regulations, and litigation that will further increase their health care costs if they do not distance themselves from health care decisions. Third, employers have modified not only most employee benefit plans, but labor market practices in general, by giving workers more choice, control, and flexibility. DC-type health benefits have existed as cafeteria plans since the 1980s. A cafeteria plan gives each employee the opportunity to determine the allocation of his or her total compensation (within employer-defined limits) among various employee benefits (primarily retirement or health). Most types of DC health benefits currently being discussed could be provided within the existing employment-based health insurance system, with or without the use of cafeteria plans. They could also allow employees to purchase health insurance directly from insurers, or they could drive new technologies and new forms of risk pooling through which health care services are provided and financed. DC health

  4. On Defining Mass

    Science.gov (United States)

    Hecht, Eugene

    2011-01-01

    Though central to any pedagogical development of physics, the concept of mass is still not well understood. Properly defining mass has proven to be far more daunting than contemporary textbooks would have us believe. And yet today the origin of mass is one of the most aggressively pursued areas of research in all of physics. Much of the excitement surrounding the Large Hadron Collider at CERN is associated with discovering the mechanism responsible for the masses of the elementary particles. This paper will first briefly examine the leading definitions, pointing out their shortcomings. Then, utilizing relativity theory, it will propose—for consideration by the community of physicists—a conceptual definition of mass predicated on the more fundamental concept of energy, more fundamental in that everything that has mass has energy, yet not everything that has energy has mass.

  5. Implementing Software Defined Radio

    CERN Document Server

    Grayver, Eugene

    2013-01-01

    Software Defined Radio makes wireless communications easier, more efficient, and more reliable. This book bridges the gap between academic research and practical implementation. When beginning a project, practicing engineers, technical managers, and graduate students can save countless hours by considering the concepts presented in these pages. The author covers the myriad options and trade-offs available when selecting an appropriate hardware architecture. As demonstrated here, the choice between hardware- and software-centric architecture can mean the difference between meeting an aggressive schedule and bogging down in endless design iterations. Because of the author’s experience overseeing dozens of failed and successful developments, he is able to present many real-life examples. Some of the key concepts covered are: Choosing the right architecture for the market – laboratory, military, or commercial Hardware platforms – FPGAs, GPPs, specialized and hybrid devices Standardization efforts to ens...

  6. Defining cyber warfare

    Directory of Open Access Journals (Sweden)

    Dragan D. Mladenović

    2012-04-01

    Full Text Available Cyber conflicts represent a new kind of warfare that is technologically developing very rapidly. Such development results in more frequent and more intensive cyber attacks undertaken by states against adversary targets, with a wide range of diverse operations, from information operations to physical destruction of targets. Nevertheless, cyber warfare is waged through the application of the same means, techniques and methods as those used in cyber criminal, terrorism and intelligence activities. Moreover, it has a very specific nature that enables states to covertly initiate attacks against their adversaries. The starting point in defining doctrines, procedures and standards in the area of cyber warfare is determining its true nature. In this paper, a contribution to this effort was made through the analysis of the existing state doctrines and international practice in the area of cyber warfare towards the determination of its nationally acceptable definition.

  7. Defining the mobilome.

    Science.gov (United States)

    Siefert, Janet L

    2009-01-01

    This chapter defines the agents that provide for the movement of genetic material which fuels the adaptive potential of life on our planet. The chapter has been structured to be broadly comprehensive, arbitrarily categorizing the mobilome into four classes: (1) transposons, (2) plasmids, (3) bacteriophage, and (4) self-splicing molecular parasites.Our increasing understanding of the mobilome is as dynamic as the mobilome itself. With continuing discovery, it is clear that nature has not confined these genomic agents of change to neat categories, but rather the classification categories overlap and intertwine. Massive sequencing efforts and their published analyses are continuing to refine our understanding of the extent of the mobilome. This chapter provides a framework to describe our current understanding of the mobilome and a foundation on which appreciation of its impact on genome evolution can be understood.

  8. Software Defined Networking

    DEFF Research Database (Denmark)

    Caba, Cosmin Marius

    Network Service Providers (NSP) often choose to overprovision their networks instead of deploying proper Quality of Services (QoS) mechanisms that allow for traffic differentiation and predictable quality. This tendency of overprovisioning is not sustainable for the simple reason that network...... resources are limited. Hence, to counteract this trend, current QoS mechanisms must become simpler to deploy and operate, in order to motivate NSPs to employ QoS techniques instead of overprovisioning. Software Defined Networking (SDN) represents a paradigm shift in the way telecommunication and data...... generic perspective (e.g. service provisioning speed, resources availability). As a result, new mechanisms for providing QoS are proposed, solutions for SDN-specific QoS challenges are designed and tested, and new network management concepts are prototyped, all aiming to improve QoS for network services...

  9. Pareto-Optimal Evaluation of Ultimate Limit States in Offshore Wind Turbine Structural Analysis

    Directory of Open Access Journals (Sweden)

    Michael Muskulus

    2015-12-01

    Full Text Available The ultimate capacity of support structures is checked with extreme loads. This is straightforward when the limit state equations depend on a single load component, and it has become common to report maxima for each load component. However, if more than one load component is influential, e.g., both axial force and bending moments, it is not straightforward how to define an extreme load. The combination of univariate maxima can be too conservative, and many different combinations of load components can result in the worst value of the limit state equations. The use of contemporaneous load vectors is typically non-conservative. Therefore, in practice, limit state checks are done for each possible load vector, from each time step of a simulation. This is not feasible when performing reliability assessments and structural optimization, where additional, time-consuming computations are involved for each load vector. We therefore propose to use Pareto-optimal loads, which are a small set of loads that together represent all possible worst case scenarios. Simulations with two reference wind turbines show that this approach can be very useful for jacket structures, whereas the design of monopiles is often governed by the bending moment only. Even in this case, the approach might be useful when approaching the structural limits during optimization.

  10. Defining the Anthropocene

    Science.gov (United States)

    Lewis, Simon; Maslin, Mark

    2016-04-01

    Time is divided by geologists according to marked shifts in Earth's state. Recent global environmental changes suggest that Earth may have entered a new human-dominated geological epoch, the Anthropocene. Should the Anthropocene - the idea that human activity is a force acting upon the Earth system in ways that mean that Earth will be altered for millions of years - be defined as a geological time-unit at the level of an Epoch? Here we appraise the data to assess such claims, first in terms of changes to the Earth system, with particular focus on very long-lived impacts, as Epochs typically last millions of years. Can Earth really be said to be in transition from one state to another? Secondly, we then consider the formal criteria used to define geological time-units and move forward through time examining whether currently available evidence passes typical geological time-unit evidence thresholds. We suggest two time periods likely fit the criteria (1) the aftermath of the interlinking of the Old and New Worlds, which moved species across continents and ocean basins worldwide, a geologically unprecedented and permanent change, which is also the globally synchronous coolest part of the Little Ice Age (in Earth system terms), and the beginning of global trade and a new socio-economic "world system" (in historical terms), marked as a golden spike by a temporary drop in atmospheric CO2, centred on 1610 CE; and (2) the aftermath of the Second World War, when many global environmental changes accelerated and novel long-lived materials were increasingly manufactured, known as the Great Acceleration (in Earth system terms) and the beginning of the Cold War (in historical terms), marked as a golden spike by the peak in radionuclide fallout in 1964. We finish by noting that the Anthropocene debate is politically loaded, thus transparency in the presentation of evidence is essential if a formal definition of the Anthropocene is to avoid becoming a debate about bias. The

  11. Teleology and Defining Sex.

    Science.gov (United States)

    Gamble, Nathan K; Pruski, Michal

    2018-07-01

    Disorders of sexual differentiation lead to what is often referred to as an intersex state. This state has medical, as well as some legal, recognition. Nevertheless, the question remains whether intersex persons occupy a state in between maleness and femaleness or whether they are truly men or women. To answer this question, another important conundrum needs to be first solved: what defines sex? The answer seems rather simple to most people, yet when morphology does not coincide with haplotypes, and genetics might not correlate with physiology the issue becomes more complex. This paper tackles both issues by establishing where the essence of sex is located and by superimposing that framework onto the issue of the intersex. This is achieved through giving due consideration to the biology of sexual development, as well as through the use of a teleological framework of the meaning of sex. Using a range of examples, the paper establishes that sex cannot be pinpointed to one biological variable but is rather determined by how the totality of one's biology is oriented towards biological reproduction. A brief consideration is also given to the way this situation could be comprehended from a Christian understanding of sex and suffering.

  12. Determination of optimum oven cooking procedures for lean beef products.

    Science.gov (United States)

    Rodas-González, Argenis; Larsen, Ivy L; Uttaro, Bethany; Juárez, Manuel; Parslow, Joyce; Aalhus, Jennifer L

    2015-11-01

    In order to determine optimum oven cooking procedures for lean beef, the effects of searing at 232 or 260°C for 0, 10, 20 or 30 min, and roasting at 160 or 135°C on semimembranosus (SM) and longissimus lumborum (LL) muscles were evaluated. In addition, the optimum determined cooking method (oven-seared for 10 min at 232°C and roasted at 135°C) was applied to SM roasts varying in weight from 0.5 to 2.5 kg. Mainly, SM muscles seared for 0 or 10 min at 232°C followed by roast at 135°C had lower cooking loss, higher external browning color, more uniform internal color, and were more tender and flavorful (P searing is the recommended oven cooking procedure; with best response from muscle roast weight ≥1 kg.

  13. RECENT APPROACHES IN THE OPTIMUM CURRENCY AREAS THEORY

    Directory of Open Access Journals (Sweden)

    AURA SOCOL

    2011-04-01

    Full Text Available This study is dealing with the endogenous characteristic of the OCA criteria, starting from the idea that a higherconformity of the business cycles will result in a better timing of the economic cycles and, thus, in getting closerto the quality of an optimum currency area. Thus, if the classical theory is focused on a static approach of theproblem, the new theories assert that these conditions are dynamic, and they cannot be positively affected evenby the establishment of the Economic and Monetary Union. The consequences are overwhelming, as theendogenous approach shows that a monetary union can be achieved even if all the conditions mentioned inMundell’s optimum currency areas theory are not met, showing that some of them may also be met subsequentto the unification. Thus, a country joining a monetary union, althogh it does not meet the criteria for an optimumcurrency area, will ex post lead to the increase of the integration and business cycle correlation degree.

  14. Determination of optimum pressurizer level for kori unit 1

    Energy Technology Data Exchange (ETDEWEB)

    Song, Dong Soo; Lee, Chang Sup; Lee Jae Yong; Kim, Yo Han; Lee, Dong Hyuk [Korea Electric Power Research Institute, Taejon (Korea, Republic of)

    1997-12-31

    To determine the optimum pressurizer water level during normal operation for Kori unit 1, performance and safety analysis are performed. The methodology is developed by evaluating {sup d}ecrease in secondary heat removal{sup e}vents such as Loss of Normal Feedwater accident. To demonstrate optimum pressurizer level setpoint, RETRAN-03 code is used for performance analysis. Analysis results of RETRAN following reactor trip are compared with the actual plant data to justify RETRAN code modelling. The results of performance and safety analyses show that the newly established level setpoints not only improve the performance of pressurizer during transient including reactor trip but also meet the design bases of the pressurizer volume and pressure. 6 refs., 5 figs. (Author)

  15. Optimum design of exploding pusher target to produce maximum neutrons

    International Nuclear Information System (INIS)

    Kitagawa, Y.; Miyanaga, N.; Kato, Y.; Nakatsuka, M.; Nishiguchi, A.; Yabe, T.; Yamanaka, C.

    1985-03-01

    Exploding pusher target experiments have been conducted with the 1.052-μm GEKKO MII two-beam glass laser system to design an optimum target, which couples to the incident laser light most effectively to produce the maximum neutrons. Since hot electrons preheat the shell entirely in spite of strongly nonuniform irradiation, a simple model can design the optimum target, of which the shell/fuel interface is accelerated to 0.5 to 0.7 times the initial radius within a laser pulse. A 2-dimensional computer simulation supports this target design. The scaling of the neutron yield N with the laser power P is N ∝ P 2.4±0.4 . (author)

  16. Determination of the Optimum Ozone Product on the Plasma Ozonizer

    International Nuclear Information System (INIS)

    Agus Purwadi; Widdi Usada; Suryadi; Isyuniarto; Sri Sukmajaya

    2002-01-01

    An experiment of the optimum ozone product determination on the cylindrical plasma ozonizer has been done. The experiment is carried out by using alternating high voltage power supply, oscilloscope CS-1577 A, flow meter and spectronik-20 instrument for the absorbance solution samples which produced by varying the physics parameter values of the discharge alternating high voltage and velocity of oxygen gas input. The plasma ozonizer is made of cylinder stainless steel as the electrode and cylinder glass as the dielectric with 1.00 mm of the discharge gap and 7.225 mm 3 of the discharge tube volume. The experiment results shows that the optimum ozone product is 0.360 mg/s obtained at the the discharge of alternating high voltage of 25.50 kV, the frequency of 1.00 kHz and the rate of oxygen gas input of 1.00 lpm. (author)

  17. Determination of optimum pressurizer level for kori unit 1

    Energy Technology Data Exchange (ETDEWEB)

    Song, Dong Soo; Lee, Chang Sup; Yong, Lee Jae; Kim, Yo Han; Lee, Dong Hyuk [Korea Electric Power Research Institute, Taejon (Korea, Republic of)

    1998-12-31

    To determine the optimum pressurizer water level during normal operation for Kori unit 1, performance and safety analysis are performed. The methodology is developed by evaluating {sup d}ecrease in secondary heat removal{sup e}vents such as Loss of Normal Feedwater accident. To demonstrate optimum pressurizer level setpoint, RETRAN-03 code is used for performance analysis. Analysis results of RETRAN following reactor trip are compared with the actual plant data to justify RETRAN code modelling. The results of performance and safety analyses show that the newly established level setpoints not only improve the performance of pressurizer during transient including reactor trip but also meet the design bases of the pressurizer volume and pressure. 6 refs., 5 figs. (Author)

  18. A methodology for selecting optimum organizations for space communities

    Science.gov (United States)

    Ragusa, J. M.

    1978-01-01

    This paper suggests that a methodology exists for selecting optimum organizations for future space communities of various sizes and purposes. Results of an exploratory study to identify an optimum hypothetical organizational structure for a large earth-orbiting multidisciplinary research and applications (R&A) Space Base manned by a mixed crew of technologists are presented. Since such a facility does not presently exist, in situ empirical testing was not possible. Study activity was, therefore, concerned with the identification of a desired organizational structural model rather than the empirical testing of it. The principal finding of this research was that a four-level project type 'total matrix' model will optimize the effectiveness of Space Base technologists. An overall conclusion which can be reached from the research is that application of this methodology, or portions of it, may provide planning insights for the formal organizations which will be needed during the Space Industrialization Age.

  19. Determining optimum aging time using novel core flooding equipment

    DEFF Research Database (Denmark)

    Ahkami, Mehrdad; Chakravarty, Krishna Hara; Xiarchos, Ioannis

    2016-01-01

    the optimum aging time regardless of variations in crude oil, rock, and brine properties. State of the art core flooding equipment has been developed that can be used for consistently determining the resistivity of the coreplug during aging and waterflooding using advanced data acquisition software......New methods for enhanced oil recovery are typically developed using core flooding techniques. Establishing reservoir conditions is essential before the experimental campaign commences. The realistic oil-rock wettability can be obtained through optimum aging of the core. Aging time is affected....... In the proposed equipment, independent axial and sleeve pressure can be applied to mimic stresses at reservoir conditions. 10 coreplugs (four sandstones and six chalk samples) from the North Sea have been aged for more than 408 days in total and more than 29000 resistivity data points have been measured...

  20. Optimum Conditions for Uricase Enzyme Production by Gliomastix gueg

    Directory of Open Access Journals (Sweden)

    Atalla, M. M.

    2009-01-01

    Full Text Available Nineteen strains of microorganisms were screened for uricase production. Gliomastix gueg was recognized to produce high levels of the enzyme. The optimum fermentation conditions for uricase production by Gliomastix gueg were examined. Results showed that uric acid medium was the most favorable one, the optimum temperature was at 30ºC, and incubation period required for maximum production was 8 days with aeration level at 150 rpm and at pH 8.0. Sucrose proved to be the best carbon source, uric acid was found to be the best nitrogen source. Both, dipotassium hydrogen phosphate and ferrous chloride as well as some vitamins gave the highest amount of uricase by Gliomastix gueg.

  1. Ultimate architecture

    CERN Multimedia

    Jencks, Charles

    2007-01-01

    "European physics hothouse CERN recently unveiled Atlas, the world's most powerful particle detector, which it will use to search for the fundamental building blocks of nature from May next year. Charles Jencks describes the experience of getting up clsoe to the engineering marvel that could en up creating a mini-black hole."(5 pages with photos).

  2. Ultimate energy

    International Nuclear Information System (INIS)

    1994-01-01

    An explanation is given of the complexity faced by the scientific researcher in an effort to achieve fusion power. Outlines the theory and current experiments being pursued in this complex project, including visits to five major fusion research laboratories, and interviews with physicists

  3. Optimum biasing of integral equations in Monte Carlo calculations

    International Nuclear Information System (INIS)

    Hoogenboom, J.E.

    1979-01-01

    In solving integral equations and estimating average values with the Monte Carlo method, biasing functions may be used to reduce the variancee of the estimates. A simple derivation was used to prove the existence of a zero-variance collision estimator if a specific biasing function and survival probability are applied. This optimum biasing function is the same as that used for the well known zero-variance last-event estimator

  4. Optimum design of Nd-doped fiber optical amplifiers

    DEFF Research Database (Denmark)

    Rasmussen, Thomas; Bjarklev, Anders Overgaard; Lumholt, Ole

    1992-01-01

    The waveguide parameters for a Nd-doped fluoride (Nd:ZBLANP) fiber amplifier have been optimized for small-signal and booster operation using an accurate numerical model. The optimum cutoff wavelength is shown to be 800 nm and the numerical aperture should be made as large as possible. Around 80%......% booster quantum conversion efficiency can be reached for an input power of 10 dBm and a pump power of 100 mW by the use of one filter...

  5. Optimum concrete compression strength using bio-enzyme

    OpenAIRE

    Bagio Tony Hartono; Basoeki Makno; Tistogondo Julistyana; Pradana Sofyan Ali

    2017-01-01

    To make concrete with high compressive strength and has a certain concrete specifications other than the main concrete materials are also needed concrete mix quality control and other added material is also in line with the current technology of concrete mix that produces concrete with specific characteristics. Addition of bio enzyme on five concrete mixture that will be compared with normal concrete in order to know the optimum level bio-enzyme in concrete to increase the strength of the con...

  6. Theoretical and numerical study of an optimum design algorithm

    International Nuclear Information System (INIS)

    Destuynder, Philippe.

    1976-08-01

    This work can be separated into two main parts. First, the behavior of the solution of an elliptic variational equation is analyzed when the domain is submitted to a small perturbation. The case of inequations is also considered. Secondly the previous results are used for deriving an optimum design algorithm. This algorithm was suggested by the center-method proposed by Huard. Numerical results show the superiority of the method on other different optimization techniques [fr

  7. Generating AN Optimum Treatment Plan for External Beam Radiation Therapy.

    Science.gov (United States)

    Kabus, Irwin

    1990-01-01

    The application of linear programming to the generation of an optimum external beam radiation treatment plan is investigated. MPSX, an IBM linear programming software package was used. All data originated from the CAT scan of an actual patient who was treated for a pancreatic malignant tumor before this study began. An examination of several alternatives for representing the cross section of the patient showed that it was sufficient to use a set of strategically placed points in the vital organs and tumor and a grid of points spaced about one half inch apart for the healthy tissue. Optimum treatment plans were generated from objective functions representing various treatment philosophies. The optimum plans were based on allowing for 216 external radiation beams which accounted for wedges of any size. A beam reduction scheme then reduced the number of beams in the optimum plan to a number of beams small enough for implementation. Regardless of the objective function, the linear programming treatment plan preserved about 95% of the patient's right kidney vs. 59% for the plan the hospital actually administered to the patient. The clinician, on the case, found most of the linear programming treatment plans to be superior to the hospital plan. An investigation was made, using parametric linear programming, concerning any possible benefits derived from generating treatment plans based on objective functions made up of convex combinations of two objective functions, however, this proved to have only limited value. This study also found, through dual variable analysis, that there was no benefit gained from relaxing some of the constraints on the healthy regions of the anatomy. This conclusion was supported by the clinician. Finally several schemes were found that, under certain conditions, can further reduce the number of beams in the final linear programming treatment plan.

  8. Choice of economical optimum blanket of hybrid reactors

    Energy Technology Data Exchange (ETDEWEB)

    Blinkin, V L; Novikov, V M

    1981-01-01

    The economical effectiveness of symbiotic power systems depends on the choice of the correlation between energy production and fissile fuel production in blankets of controlled thermonuclear fusion reactor (CTR), what is investigated here. It is shown that the optimum value of this correlation essentially depends on the ratio between the specific costs for energy production in hybrid thermonuclear reactors and that in fission reactors as part of the symbiotic system.

  9. Defining an emerging disease.

    Science.gov (United States)

    Moutou, F; Pastoret, P-P

    2015-04-01

    Defining an emerging disease is not straightforward, as there are several different types of disease emergence. For example, there can be a 'real' emergence of a brand new disease, such as the emergence of bovine spongiform encephalopathy in the 1980s, or a geographic emergence in an area not previously affected, such as the emergence of bluetongue in northern Europe in 2006. In addition, disease can emerge in species formerly not considered affected, e.g. the emergence of bovine tuberculosis in wildlife species since 2000 in France. There can also be an unexpected increase of disease incidence in a known area and a known species, or there may simply be an increase in our knowledge or awareness of a particular disease. What all these emerging diseases have in common is that human activity frequently has a role to play in their emergence. For example, bovine spongiform encephalopathy very probably emerged as a result of changes in the manufacturing of meat-and-bone meal, bluetongue was able to spread to cooler climes as a result of uncontrolled trade in animals, and a relaxation of screening and surveillance for bovine tuberculosis enabled the disease to re-emerge in areas that had been able to drastically reduce the number of cases. Globalisation and population growth will continue to affect the epidemiology of diseases in years to come and ecosystems will continue to evolve. Furthermore, new technologies such as metagenomics and high-throughput sequencing are identifying new microorganisms all the time. Change is the one constant, and diseases will continue to emerge, and we must consider the causes and different types of emergence as we deal with these diseases in the future.

  10. An integrated expert system for optimum in core fuel management

    International Nuclear Information System (INIS)

    Abd Elmoatty, Mona S.; Nagy, M.S.; Aly, Mohamed N.; Shaat, M.K.

    2011-01-01

    Highlights: → An integrated expert system constructed for optimum in core fuel management. → Brief discussion of the ESOIFM Package modules, inputs and outputs. → Package was applied on the DALAT Nuclear Research Reactor (0.5 MW). → The Package verification showed good agreement. - Abstract: An integrated expert system called Efficient and Safe Optimum In-core Fuel Management (ESOIFM Package) has been constructed to achieve an optimum in core fuel management and automate the process of data analysis. The Package combines the constructed mathematical models with the adopted artificial intelligence techniques. The paper gives a brief discussion of the ESOIFM Package modules, inputs and outputs. The Package was applied on the DALAT Nuclear Research Reactor (0.5 MW). Moreover, the data of DNRR have been used as a case study for testing and evaluation of ESOIFM Package. This paper shows the comparison between the ESOIFM Package burn-up results, the DNRR experimental burn-up data, and other DNRR Codes burn-up results. The results showed good agreement.

  11. Optimum profit model considering production, quality and sale problem

    Science.gov (United States)

    Chen, Chung-Ho; Lu, Chih-Lun

    2011-12-01

    Chen and Liu ['Procurement Strategies in the Presence of the Spot Market-an Analytical Framework', Production Planning and Control, 18, 297-309] presented the optimum profit model between the producers and the purchasers for the supply chain system with a pure procurement policy. However, their model with a simple manufacturing cost did not consider the used cost of the customer. In this study, the modified Chen and Liu's model will be addressed for determining the optimum product and process parameters. The authors propose a modified Chen and Liu's model under the two-stage screening procedure. The surrogate variable having a high correlation with the measurable quality characteristic will be directly measured in the first stage. The measurable quality characteristic will be directly measured in the second stage when the product decision cannot be determined in the first stage. The used cost of the customer will be measured by adopting Taguchi's quadratic quality loss function. The optimum purchaser's order quantity, the producer's product price and the process quality level will be jointly determined by maximising the expected profit between them.

  12. An optimum analysis sequence for environmental gamma-ray spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    De la Torre, F.; Rios M, C.; Ruvalcaba A, M. G.; Mireles G, F.; Saucedo A, S.; Davila R, I.; Pinedo, J. L., E-mail: fta777@hotmail.co [Universidad Autonoma de Zacatecas, Centro Regional de Estudis Nucleares, Calle Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas (Mexico)

    2010-10-15

    This work aims to obtain an optimum analysis sequence for environmental gamma-ray spectroscopy by means of Genie 2000 (Canberra). Twenty different analysis sequences were customized using different peak area percentages and different algorithms for: 1) peak finding, and 2) peak area determination, and with or without the use of a library -based on evaluated nuclear data- of common gamma-ray emitters in environmental samples. The use of an optimum analysis sequence with certified nuclear information avoids the problems originated by the significant variations in out-of-date nuclear parameters of commercial software libraries. Interference-free gamma ray energies with absolute emission probabilities greater than 3.75% were included in the customized library. The gamma-ray spectroscopy system (based on a Ge Re-3522 Canberra detector) was calibrated both in energy and shape by means of the IAEA-2002 reference spectra for software intercomparison. To test the performance of the analysis sequences, the IAEA-2002 reference spectrum was used. The z-score and the reduced {chi}{sup 2} criteria were used to determine the optimum analysis sequence. The results show an appreciable variation in the peak area determinations and their corresponding uncertainties. Particularly, the combination of second derivative peak locate with simple peak area integration algorithms provides the greater accuracy. Lower accuracy comes from the combination of library directed peak locate algorithm and Genie's Gamma-M peak area determination. (Author)

  13. An optimum analysis sequence for environmental gamma-ray spectrometry

    International Nuclear Information System (INIS)

    De la Torre, F.; Rios M, C.; Ruvalcaba A, M. G.; Mireles G, F.; Saucedo A, S.; Davila R, I.; Pinedo, J. L.

    2010-10-01

    This work aims to obtain an optimum analysis sequence for environmental gamma-ray spectroscopy by means of Genie 2000 (Canberra). Twenty different analysis sequences were customized using different peak area percentages and different algorithms for: 1) peak finding, and 2) peak area determination, and with or without the use of a library -based on evaluated nuclear data- of common gamma-ray emitters in environmental samples. The use of an optimum analysis sequence with certified nuclear information avoids the problems originated by the significant variations in out-of-date nuclear parameters of commercial software libraries. Interference-free gamma ray energies with absolute emission probabilities greater than 3.75% were included in the customized library. The gamma-ray spectroscopy system (based on a Ge Re-3522 Canberra detector) was calibrated both in energy and shape by means of the IAEA-2002 reference spectra for software intercomparison. To test the performance of the analysis sequences, the IAEA-2002 reference spectrum was used. The z-score and the reduced χ 2 criteria were used to determine the optimum analysis sequence. The results show an appreciable variation in the peak area determinations and their corresponding uncertainties. Particularly, the combination of second derivative peak locate with simple peak area integration algorithms provides the greater accuracy. Lower accuracy comes from the combination of library directed peak locate algorithm and Genie's Gamma-M peak area determination. (Author)

  14. WHAT IS THE OPTIMUM SIZE OF GOVERNMENT: A SUGGESTION

    Directory of Open Access Journals (Sweden)

    Aykut Ekinci

    2011-01-01

    Full Text Available What is the optimum size of government? When the rule of law and the establishment of private property rights are taken into consideration, it is clear that the answer will not be at some 0%. On the other hand, when the experience of the old Soviet Union, East Germany and North Korea is considered, the answer will not be at some 100% either. Therefore, extreme points should not be the right answer. This study offers using normal distribution to answer this question. The study has revealed the following findings: (i The total amount of public expenditures as % of GDP, a is at minimum level at 4.55% rate, b is at optimum level at 13.4% rate, c is at maximum level at 31.7%. (ii Thus, as a fiscal rule, countries should: a choose the total amount of public expenditures as % of GDP ≤ 31.7% b target 13.4%. (iii Tree dimensional (3D normal distribution demonstrates that a healthy market system could be built upon a healthy government system (iv This approach rejects Wagner’s law. In a healthy growing economy, optimum government size could be kept at 13.4%. (v The UK, the USA and the European countries have been in the Keynesian-Marxist area, which reduces their average growth.

  15. Optimum Antenna Downtilt Angles for Macrocellular WCDMA Network

    Directory of Open Access Journals (Sweden)

    Niemelä Jarno

    2005-01-01

    Full Text Available The impact of antenna downtilt on the performance of cellular WCDMA network has been studied by using a radio network planning tool. An optimum downtilt angle has been evaluated for numerous practical macrocellular site and antenna configurations for electrical and mechanical antenna downtilt concepts. The aim of this massive simulation campaign was expected to provide an answer to two questions: firstly, how to select the downtilt angle of a macrocellular base station antenna? Secondly, what is the impact of antenna downtilt on system capacity and network coverage? Optimum downtilt angles were observed to vary between – depending on the network configuration. Moreover, the corresponding downlink capacity gains varied between – . Antenna vertical beamwidth affects clearly the required optimum downtilt angle the most. On the other hand, with wider antenna vertical beamwidth, the impact of downtilt on system performance is not such imposing. In addition, antenna height together with the size of the dominance area affect the required downtilt angle. Finally, the simulation results revealed how the importance of the antenna downtilt becomes more significant in dense networks, where the capacity requirements are typically also higher.

  16. Planning of optimum production from a natural gas field

    Energy Technology Data Exchange (ETDEWEB)

    Van Dam, J

    1968-03-01

    The design of an optimum development plan for a natural gas field always depends on the typical characteristics of the producing field, as well as those of the market to be served by this field. Therefore, a good knowledge of the field parameters, such as the total natural gas reserves, the well productivity, and the dependence of production rates on pipeline pressure and depletion of natural gas reserves, is required prior to designing the development scheme of the field, which in fact depends on the gas-sales contract to be concluded in order to commit the natural gas reserves to the market. In this paper these various technical parameters are discussed in some detail, and on this basis a theoretical/economical analysis of natural gas production is given. For this purpose a simplified economical/mathematical model for the field is proposed, from which optimum production rates at various future dates can be calculated. The results of these calculations are represented in a dimensionless diagram which may serve as an aid in designing optimum development plans for a natural gas field. The use of these graphs is illustrated in a few examples.

  17. Semianalytical and Seminumerical Calculations of Optimum Material Distributions

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Gunnar

    1963-06-15

    Perturbation theory applied to the multigroup diffusion equations gives a general condition for optimum distribution of reactor materials. A certain function of the material densities and the fluxes, here called the W (eight) function, must thus be constant where the variable material density is larger than zero if changes in this density affect only the group constants where the changes occur. The weight function is, however, generally a complicated function and complete solutions have therefore previously been presented only for the special case when constant weight function implies constant thermal flux. It is demonstrated that the condition of constant weight function can be used together with well known methods for numerical solution of the multigroup diffusion equations to obtain optimum material distributions also when the thermal flux varies over the core. Solution of the minimum fuel mass problem for two reflected reactors thus shows that an effective reflector such as D{sub 2}O gives a peak in the optimum fuel distribution at the core-reflector interface, while an ineffective reflector such as a breeder blanket or a steel tank wall 'pushes' the fuel away from the strongly absorbing zone. It is also interesting to compare the effective reflector case with analytically obtained solutions corresponding to flat power density, flat thermal flux and flat fuel density.

  18. Optimum heat power cycles for specified boundary conditions

    International Nuclear Information System (INIS)

    Ibrahim, O.M.; Klein, S.A.; Mitchell, J.W.

    1991-01-01

    In this paper optimization of the power output of Carnot and closed Brayton cycles is considered for both finite and infinite thermal capacitance rates of the external fluid streams. The method of Lagrange multipliers is used to solve for working fluid temperatures that yield maximum power. Analytical expressions for the maximum power and the cycle efficiency at maximum power are obtained. A comparison of the maximum power from the two cycles for the same boundary conditions, i.e., the same heat source/sink inlet temperatures, thermal capacitance rates, and heat exchanger conductances, shows that the Brayton cycle can produce more power than the Carnot cycle. This comparison illustrates that cycles exist that can produce more power than the Carnot cycle. The optimum heat power cycle, which will provide the upper limit of power obtained from any thermodynamic cycle for specified boundary conditions and heat exchanger conductances is considered. The optimum heat power cycle is identified by optimizing the sum of the power output from a sequence of Carnot cycles. The shape of the optimum heat power cycle, the power output, and corresponding efficiency are presented. The efficiency at maximum power of all cycles investigated in this study is found to be equal to (or well approximated by) η = 1 - sq. root T L.in /φT H.in where φ is a factor relating the entropy changes during heat rejection and heat addition

  19. Optimum moisture levels for biodegradation of mortality composting envelope materials.

    Science.gov (United States)

    Ahn, H K; Richard, T L; Glanville, T D

    2008-01-01

    Moisture affects the physical and biological properties of compost and other solid-state fermentation matrices. Aerobic microbial systems experience different respiration rates (oxygen uptake and CO2 evolution) as a function of moisture content and material type. In this study the microbial respiration rates of 12 mortality composting envelope materials were measured by a pressure sensor method at six different moisture levels. A wide range of respiration (1.6-94.2mg O2/g VS-day) rates were observed for different materials, with alfalfa hay, silage, oat straw, and turkey litter having the highest values. These four envelope materials may be particularly suitable for improving internal temperature and pathogen destruction rates for disease-related mortality composting. Optimum moisture content was determined based on measurements across a range that spans the maximum respiration rate. The optimum moisture content of each material was observed near water holding capacity, which ranged from near 60% to over 80% on a wet basis for all materials except a highly stabilized soil compost blend (optimum around 25% w.b.). The implications of the results for moisture management and process control strategies during mortality composting are discussed.

  20. Optimum structure of Whipple shield against hypervelocity impact

    International Nuclear Information System (INIS)

    Lee, M

    2014-01-01

    Hypervelocity impact of a spherical aluminum projectile onto two spaced aluminum plates (Whipple shield) was simulated to estimate an optimum structure. The Smooth Particle Hydrodynamics (SPH) code which has a unique migration scheme from a rectangular coordinate to an axisymmetic coordinate was used. The ratio of the front plate thickness to sphere diameter varied from 0.06 to 0.48. The impact velocities considered here were 6.7 km/s. This is the procedure we explored. To guarantee the early stage simulation, the shapes of debris clouds were first compared with the previous experimental pictures, indicating a good agreement. Next, the debris cloud expansion angle was predicted and it shows a maximum value of 23 degree for thickness ratio of front bumper to sphere diameter of 0.23. A critical sphere diameter causing failure of rear wall was also examined while keeping the total thickness of two plates constant. There exists an optimum thickness ratio of front bumper to rear wall, which is identified as a function of the size combination of the impacting body, front and rear plates. The debris cloud expansion-correlated-optimum thickness ratio study provides a good insight on the hypervelocity impact onto spaced target system.

  1. Optimum structure of Whipple shield against hypervelocity impact

    Science.gov (United States)

    Lee, M.

    2014-05-01

    Hypervelocity impact of a spherical aluminum projectile onto two spaced aluminum plates (Whipple shield) was simulated to estimate an optimum structure. The Smooth Particle Hydrodynamics (SPH) code which has a unique migration scheme from a rectangular coordinate to an axisymmetic coordinate was used. The ratio of the front plate thickness to sphere diameter varied from 0.06 to 0.48. The impact velocities considered here were 6.7 km/s. This is the procedure we explored. To guarantee the early stage simulation, the shapes of debris clouds were first compared with the previous experimental pictures, indicating a good agreement. Next, the debris cloud expansion angle was predicted and it shows a maximum value of 23 degree for thickness ratio of front bumper to sphere diameter of 0.23. A critical sphere diameter causing failure of rear wall was also examined while keeping the total thickness of two plates constant. There exists an optimum thickness ratio of front bumper to rear wall, which is identified as a function of the size combination of the impacting body, front and rear plates. The debris cloud expansion-correlated-optimum thickness ratio study provides a good insight on the hypervelocity impact onto spaced target system.

  2. The optimum decision rules for the oddity task.

    Science.gov (United States)

    Versfeld, N J; Dai, H; Green, D M

    1996-01-01

    This paper presents the optimum decision rule for an m-interval oddity task in which m-1 intervals contain the same signal and one is different or odd. The optimum decision rule depends on the degree of correlation among observations. The present approach unifies the different strategies that occur with "roved" or "fixed" experiments (Macmillan & Creelman, 1991, p. 147). It is shown that the commonly used decision rule for an m-interval oddity task corresponds to the special case of highly correlated observations. However, as is also true for the same-different paradigm, there exists a different optimum decision rule when the observations are independent. The relation between the probability of a correct response and d' is derived for the three-interval oddity task. Tables are presented of this relation for the three-, four-, and five-interval oddity task. Finally, an experimental method is proposed that allows one to determine the decision rule used by the observer in an oddity experiment.

  3. 75 FR 76746 - Agency Information Collection Activities: Declaration of Ultimate Consignee That Articles Were...

    Science.gov (United States)

    2010-12-09

    ... Activities: Declaration of Ultimate Consignee That Articles Were Exported for Temporary Scientific or... That Articles Were Exported for Temporary Scientific or Educational Purposes. This is a proposed... forms of information. Title: Declaration of Ultimate Consignee That Articles Were Exported for Temporary...

  4. 7 CFR 4280.21 - Eligible REDG Ultimate Recipients and Projects.

    Science.gov (United States)

    2010-01-01

    ... care providers; (5) Projects that utilize Advanced Telecommunications or computer networks to... 7 Agriculture 15 2010-01-01 2010-01-01 false Eligible REDG Ultimate Recipients and Projects. 4280... Economic Development Loan and Grant Programs § 4280.21 Eligible REDG Ultimate Recipients and Projects. The...

  5. 78 FR 55117 - Ultimate Heat Sink for Nuclear Power Plants; Draft Regulatory Guide

    Science.gov (United States)

    2013-09-09

    ... NUCLEAR REGULATORY COMMISSION [NRC-2013-0203] Ultimate Heat Sink for Nuclear Power Plants; Draft... (DG), DG-1275, ``Ultimate Heat Sink for Nuclear Power Plants.'' This regulatory guide (RG) describes methods and procedures acceptable to the NRC staff that nuclear power plant facility licensees and...

  6. Influence of cracks and pitting corrosion on residual ultimate strength of stiffened plates

    Directory of Open Access Journals (Sweden)

    ZHANG Jing

    2018-02-01

    Full Text Available [Objectives] Ships and offshore platforms serve in the harsh sea environment for a long time. Cracks and pitting corrosion will occur in such a structure and the damage will affect its ultimate strength.[Methods] To investigate the influence of cracks and pitting corrosion on ultimate bearing capacity, the ultimate strength of a structure under axial compression is studied by using a nonlinear finite element. The mesh size of a stiffened plate with cracks and pitting corrosion is first discussed. Then the influence of the relative positions of cracks and pitting corrosion, number of corrosion points and crack length impact on the residual ultimate strength of damaged stiffened plates is discussed via a series of calculations.[Results] The results indicate that the increase in crack length and pitting corrosion significantly decreases the ultimate strength of a stiffened plate. [Conclusions] This provides a useful reference for designing and maintaining ships and offshore structures in their life cycles.

  7. Ultimate capacity and influenced factors analysis of nuclear RC containment subjected to internal pressure

    International Nuclear Information System (INIS)

    Song Chenning; Hou Gangling; Zhou Guoliang

    2014-01-01

    Ultimate compressive bearing capacity, influenced factors and its rules of nuclear RC containment are key problems of safety assessment, accident treatment and structure design, etc. Ultimate compressive bearing capacity of nuclear RC containment is shown by concrete damaged plasticity model and steel double liner model of ABAQUS. The study shows that the concrete of nuclear RC containment cylinder wall becomes plastic when the internal pressure is up to 0.87 MPa, the maximum tensile strain of steel liner exceeds 3000 × 10 6 and nuclear RC containment reaches ultimate status when the internal pressure is up to 1.02 MPa. The result shows that nuclear RC containment is in elastic condition under the design internal pressure and the bearing capacity meets requirement. Prestress and steel liner play key parts in the ultimate internal pressure and failure mode of nuclear RC containment. The study results have value for the analysis of ultimate compressive bearing capacity, structure design and safety assessment. (authors)

  8. Analytical and numerical calculations of optimum design frequency for focused ultrasound therapy and acoustic radiation force.

    Science.gov (United States)

    Ergün, A Sanlı

    2011-10-01

    Focused ultrasound therapy relies on acoustic power absorption by tissue. The stronger the absorption the higher the temperature increase is. However, strong acoustic absorption also means faster attenuation and limited penetration depth. Hence, there is a trade-off between heat generation efficacy and penetration depth. In this paper, we formulated the acoustic power absorption as a function of frequency and attenuation coefficient, and defined two figures of merit to measure the power absorption: spatial peak of the acoustic power absorption density, and the acoustic power absorbed within the focal area. Then, we derived "rule of thumb" expressions for the optimum frequencies that maximized these figures of merit given the target depth and homogeneous tissue type. We also formulated a method to calculate the optimum frequency for inhomogeneous tissue given the tissue composition for situations where the tissue structure can be assumed to be made of parallel layers of homogeneous tissue. We checked the validity of the rules using linear acoustic field simulations. For a one-dimensional array of 4cm acoustic aperture, and for a two-dimensional array of 4×4cm(2) acoustic aperture, we found that the power absorbed within the focal area is maximized at 0.86MHz, and 0.79MHz, respectively, when the target depth is 4cm in muscle tissue. The rules on the other hand predicted the optimum frequencies for acoustic power absorption as 0.9MHz and 0.86MHz, respectively for the 1D and 2D array case, which are within 6% and 9% of the field simulation results. Because radiation force generated by an acoustic wave in a lossy propagation medium is approximately proportional to the acoustic power absorption, these rules can be used to maximize acoustic radiation force generated in tissue as well. Copyright © 2011 Elsevier B.V. All rights reserved.

  9. Just caring: defining a basic benefit package.

    Science.gov (United States)

    Fleck, Leonard M

    2011-12-01

    What should be the content of a package of health care services that we would want to guarantee to all Americans? This question cannot be answered adequately apart from also addressing the issue of fair health care rationing. Consequently, as I argue in this essay, appeal to the language of "basic," "essential," "adequate," "minimally decent," or "medically necessary" for purposes of answering our question is unhelpful. All these notions are too vague to be useful. Cost matters. Effectiveness matters. The clinical circumstances of a patient matters. But what we must ultimately determine is what we mutually agree are the just claims to needed health care of each American in a relatively complex range of clinical circumstances. Answering this question will require a public moral conversation, a fair process of rational democratic deliberation aimed at defining both just claims to needed health care and just limits.

  10. Definably compact groups definable in real closed fields.II

    OpenAIRE

    Barriga, Eliana

    2017-01-01

    We continue the analysis of definably compact groups definable in a real closed field $\\mathcal{R}$. In [3], we proved that for every definably compact definably connected semialgebraic group $G$ over $\\mathcal{R}$ there are a connected $R$-algebraic group $H$, a definable injective map $\\phi$ from a generic definable neighborhood of the identity of $G$ into the group $H\\left(R\\right)$ of $R$-points of $H$ such that $\\phi$ acts as a group homomorphism inside its domain. The above result and o...

  11. Global warming and ocean acidification through halted weathering feedback during the Middle Eocene Climatic Optimum

    Science.gov (United States)

    van der Ploeg, R.; Selby, D. S.; Cramwinckel, M.; Bohaty, S. M.; Sluijs, A.; Middelburg, J. J.

    2016-12-01

    The Middle Eocene Climatic Optimum (MECO) represents a 500 kyr period of global warming 40 million years ago associated with a rise in atmospheric CO2 concentrations, but its cause remains enigmatic. Moreover, on the timescale of the MECO, an increase in silicate weathering rates on the continents is expected to balance carbon input and restore the alkalinity of the oceans, but this is in sharp disagreement with observations of extensive carbonate dissolution. Here we show, based on osmium isotope ratios of marine sediments from three different sites, that CO2 rise and warming did not lead to enhanced continental weathering during the MECO, in contrast to expectations from carbon cycle theory. Remarkably, a minor shift to lower, more unradiogenic osmium isotope ratios rather indicates an episode of increased volcanism or reduced continental weathering. This disproves silicate weathering as a geologically constant feedback to CO2 variations. Rather, we suggest that global Early and Middle Eocene warmth diminished the weatherability of continental rocks, ultimately leading to CO2 accumulation during the MECO, and show the plausibility of this scenario using carbon cycle modeling simulations. We surmise a dynamic weathering feedback might explain multiple enigmatic phases of coupled climate and carbon cycle change in the Cretaceous and Cenozoic.

  12. SYNTHESIS OF THE SERVO DRIVER WITH SPEED LOOP TUNED AT THE MODULAR OPTIMUM

    Directory of Open Access Journals (Sweden)

    Mr. Sergei V. Stelmashchuk

    2016-12-01

    Full Text Available The paper presents a method of synthesis of servo driver for controlling the speed of the object with the speed tuned at the modular optimum. An automatic electric motor drive is considered as the controlled element. This assumes the use of the speed sensor on the output shaft of the drive gear. This approach can be used for geared motors, which are more commonly used in a variety of compact drives. The technique is based on the method of synthesis by using logarithmic frequency response (LFR. The result is a synthesis of the two tracking angle controllers: proportional-integral and proportional-derivative (PIPD regulator. The criterion for the synthesis of tracking angle controller is the desired LFR, the characteristics of which are defined based on saturated capability transition function of controlled object with standard configuration for modular optimum. It is assumed that the maximum speed and acceleration of the transition functions are required for the synthesis of parameters of servo driver system by LFR. The article covers the accuracy and contains an example of a particular electric motor.

  13. Model for Determining the Optimum Location for Performance Improvement in Supply-Chain Strategies

    Directory of Open Access Journals (Sweden)

    Ramona Iulia ȚARȚAVULEA (DIEACONESCU

    2015-06-01

    Full Text Available The economic crisis which started in 2007 has caused damaging effects to most international companies. In several EU countries, foreign investments decreased and international companies closed or relocated production and/or distribution centres, due to cost reduction measures. This paper is aiming to demonstrate that applying a performant solution in defining the supply chain strategy can be a low cost process, which can generate positive effects on the sales and revenues. The research objective is to present a concrete solution for redesigning the supply chain, in order to achieve the optimal delivery strategy. The solution implies the use of mathematic methods, for determining the optimum location for placing a central warehouse, in a geographic region. The use of an optimum delivery strategy leads to lower depositing and transport costs, which generates positive effects on sales, by offering more competitive prices on products. The main contribution of the author is the development of a model, used to identify the optimal location for placing a central warehouse.

  14. A study on nonlinear behavior of reactor containment structures during ultimate accident condition(I)

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sun Hoon; Kim, Young Jin; Park, Joo Yeon [Youngdong Univ., Yeongdong (Korea, Republic of)] (and others)

    2003-03-15

    In this study, the following scope and contents are established for first year's study of determining ultimate pressure capacity of CANDU-type reactor containment. State-of-arts on the prediction of the ultimate pressure capacity of prestressed concrete reactor containment. Comparative study on structural characteristics and analysis model of CANDU-type reactor containment. State-of-arts on evaluation method of the ultimate pressure capacity of prestressed concrete reactor containment. Enhancement of evaluation method of the ultimate pressure capacity for PWR containment structure. In order to determine a realistic lower bound of a typical reactor containment structural capacity for internal pressure, modelling techniques and analytical investigation to predict its non-linear behavior up to ultimate capacity are required. Especially, the in-depth evaluation of modeling technique and analysis procedure for determining ultimate pressure capacity of CANDU-type reactor containment is required. Therefore, modelling techniques and analytical investigation to predict its non-linear behavior up to ultimate pressure capacity of CANDU-type reactor containment for internal pressure will be suggested in this study.

  15. A study on nonlinear behavior of reactor containment structures during ultimate accident condition(I)

    International Nuclear Information System (INIS)

    Kim, Sun Hoon; Kim, Young Jin; Park, Joo Yeon

    2003-03-01

    In this study, the following scope and contents are established for first year's study of determining ultimate pressure capacity of CANDU-type reactor containment. State-of-arts on the prediction of the ultimate pressure capacity of prestressed concrete reactor containment. Comparative study on structural characteristics and analysis model of CANDU-type reactor containment. State-of-arts on evaluation method of the ultimate pressure capacity of prestressed concrete reactor containment. Enhancement of evaluation method of the ultimate pressure capacity for PWR containment structure. In order to determine a realistic lower bound of a typical reactor containment structural capacity for internal pressure, modelling techniques and analytical investigation to predict its non-linear behavior up to ultimate capacity are required. Especially, the in-depth evaluation of modeling technique and analysis procedure for determining ultimate pressure capacity of CANDU-type reactor containment is required. Therefore, modelling techniques and analytical investigation to predict its non-linear behavior up to ultimate pressure capacity of CANDU-type reactor containment for internal pressure will be suggested in this study

  16. Studies on optimum harvest time for hybrid rice seed.

    Science.gov (United States)

    Fu, Hong; Cao, Dong-Dong; Hu, Wei-Min; Guan, Ya-Jing; Fu, Yu-Ying; Fang, Yong-Feng; Hu, Jin

    2017-03-01

    Timely harvest is critical for hybrid rice to achieve maximum seed viability, vigor and yield. However, how to predict the optimum harvest time has been rarely reported so far. The seed vigor of Zhuliangyou 06 (ZLY06) increased and reached the highest level at 20 days after pollination (DAP), when seed moisture content had a lower value, which was maintained until final seed maturation. For Chunyou 84 (CY84), seed vigor, fresh and dry weight had relatively high values at 25 DAP, when seed moisture content reached the lowest value and changed slightly from 25 to 55 DAP. In both hybrid rice varieties, seed glume chlorophyll content declined rapidly from 10 to 30 DAP and remained at a very low level after 35 DAP. Starch content exhibited an increasing trend during seed maturation, while both soluble sugar content and amylase activity decreased significantly at the early stages of seed development. Moreover, correlation analyses showed that seed dry weight, starch content and superoxide dismutase activity were significantly positively correlated with seed vigor. In contrast, chlorophyll content, moisture content, soluble sugar, soluble protein, abscisic acid, gibberellin content, electrical conductivity, catalase and ascorbate peroxidase activities were significantly negatively correlated with seed vigor. Physiological and biochemical parameters were obviously more closely related with seed vigor than with seed germinability during seed development. Seed vigor could be better used as a comprehensive factor to predict the optimum seed harvest time. It is suggested that for ZLY06 seeds could be harvested as early as 20 DAP, whereas for CY84 the earliest optimum harvest time was 25 DAP. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  17. Developed Hybrid Model for Propylene Polymerisation at Optimum Reaction Conditions

    Directory of Open Access Journals (Sweden)

    Mohammad Jakir Hossain Khan

    2016-02-01

    Full Text Available A statistical model combined with CFD (computational fluid dynamic method was used to explain the detailed phenomena of the process parameters, and a series of experiments were carried out for propylene polymerisation by varying the feed gas composition, reaction initiation temperature, and system pressure, in a fluidised bed catalytic reactor. The propylene polymerisation rate per pass was considered the response to the analysis. Response surface methodology (RSM, with a full factorial central composite experimental design, was applied to develop the model. In this study, analysis of variance (ANOVA indicated an acceptable value for the coefficient of determination and a suitable estimation of a second-order regression model. For better justification, results were also described through a three-dimensional (3D response surface and a related two-dimensional (2D contour plot. These 3D and 2D response analyses provided significant and easy to understand findings on the effect of all the considered process variables on expected findings. To diagnose the model adequacy, the mathematical relationship between the process variables and the extent of polymer conversion was established through the combination of CFD with statistical tools. All the tests showed that the model is an excellent fit with the experimental validation. The maximum extent of polymer conversion per pass was 5.98% at the set time period and with consistent catalyst and co-catalyst feed rates. The optimum conditions for maximum polymerisation was found at reaction temperature (RT 75 °C, system pressure (SP 25 bar, and 75% monomer concentration (MC. The hydrogen percentage was kept fixed at all times. The coefficient of correlation for reaction temperature, system pressure, and monomer concentration ratio, was found to be 0.932. Thus, the experimental results and model predicted values were a reliable fit at optimum process conditions. Detailed and adaptable CFD results were capable

  18. Seismic shear wall ISP NUPEC's seismic ultimate dynamic response test. Comparison report

    International Nuclear Information System (INIS)

    1996-01-01

    In the seismic design of a nuclear power plant, evaluation of the ultimate strength of the nuclear reactor building is an important subject for assessment of seismic reliability of the plant. In order to carry out the evaluation, the response characteristics of reinforced concrete seismic shear walls up to their ultimate state have to be understood. For this purpose, there is a need to develop reliable non-linear response analysis methods which enables the reliable ultimate strength evaluation of nuclear reactor buildings. Along with this need, many computer codes have been developed. These computer codes are compared. (K.A.)

  19. Is optimum and effective work done in administrative jurisdiction

    International Nuclear Information System (INIS)

    Hoecht, H.

    1980-01-01

    Is optimum and effective work done in administrative jurisdiction. The author describes the general situation prevailing in administrative jurisdiction. He gives tables on the number of subjects received per annum, of judges administering justice and figures on executed and non-executed proceedings. He reports on districts of jurisdiction, personnel, court administration and the amount of work. The investigation into administrative jurisdiction has shown accomplishments for 1978 which are not bad at all. Sporadic administrative shortcomings are to be realized and put to an end. (HSCH) [de

  20. Optimum filter-based discrimination of neutrons and gamma rays

    International Nuclear Information System (INIS)

    Amiri, Moslem; Prenosil, Vaclav; Cvachovec, Frantisek

    2015-01-01

    An optimum filter-based method for discrimination of neutrons and gamma-rays in a mixed radiation field is presented. The existing filter-based implementations of discriminators require sample pulse responses in advance of the experiment run to build the filter coefficients, which makes them less practical. Our novel technique creates the coefficients during the experiment and improves their quality gradually. Applied to several sets of mixed neutron and photon signals obtained through different digitizers using stilbene scintillator, this approach is analyzed and its discrimination quality is measured. (authors)

  1. Optimum policies for a system with general imperfect maintenance

    International Nuclear Information System (INIS)

    Sheu, S.-H.; Lin, Y.-B.; Liao, G.-L.

    2006-01-01

    This study considers periodic preventive maintenance policies, which maximizes the availability of a repairable system with major repair at failure. Three types of preventive maintenance are performed, namely: imperfect preventive maintenance (IPM), perfect preventive maintenance (PPM) and failed preventive maintenance (FPM). The probability that preventive maintenance is perfect depends on the number of imperfect maintenances conducted since the previous renewal cycle, and the probability that preventive maintenance remains imperfect is not increasing. The optimum preventive maintenance time that maximizes availability is derived. Various special cases are considered. A numerical example is given

  2. Optimum amount of an insurance sum in life insurance

    Directory of Open Access Journals (Sweden)

    Janez Balkovec

    2001-01-01

    Full Text Available Personal insurance represents one of the sources of personal social security as a category of personal property. How to get a proper life insurance is a frequently asked question. When insuring material objects (car, house..., the problem is usually not in the amount of the taken insurance. With life insurance (abstract goods, problems as such occur. In this paper, we wish to present a model that, according to the financial situation and the anticipated future, makes it possible to calculate the optimum insurance sum in life insurance.

  3. Search for an optimum time response of spark counters

    International Nuclear Information System (INIS)

    Devismes, A.; Finck, Ch.; Kress, T.; Gobbi, A.; Eschke, J.; Herrmann, N.; Hildenbrand, K.D.; Koczon, P.; Petrovici, M.

    2002-01-01

    A spark counter of the type developed by Pestov has been tested with the aim of searching for an optimum time response function, changing voltage, content of noble and quencher gases, pressure and energy-loss. Replacing the usual argon by neon has brought an improvement of the resolution and a significant reduction of tails in the time response function. It has been proven that a counter as long as 90 cm can deliver, using neon gas mixture, a time resolution σ<60 ps with about 1% absolute tail and an efficiency of about 90%

  4. Design optimum frac jobs using virtual intelligence techniques

    Science.gov (United States)

    Mohaghegh, Shahab; Popa, Andrei; Ameri, Sam

    2000-10-01

    Designing optimal frac jobs is a complex and time-consuming process. It usually involves the use of a two- or three-dimensional computer model. For the computer models to perform as intended, a wealth of input data is required. The input data includes wellbore configuration and reservoir characteristics such as porosity, permeability, stress and thickness profiles of the pay layers as well as the overburden layers. Among other essential information required for the design process is fracturing fluid type and volume, proppant type and volume, injection rate, proppant concentration and frac job schedule. Some of the parameters such as fluid and proppant types have discrete possible choices. Other parameters such as fluid and proppant volume, on the other hand, assume values from within a range of minimum and maximum values. A potential frac design for a particular pay zone is a combination of all of these parameters. Finding the optimum combination is not a trivial process. It usually requires an experienced engineer and a considerable amount of time to tune the parameters in order to achieve desirable outcome. This paper introduces a new methodology that integrates two virtual intelligence techniques, namely, artificial neural networks and genetic algorithms to automate and simplify the optimum frac job design process. This methodology requires little input from the engineer beyond the reservoir characterizations and wellbore configuration. The software tool that has been developed based on this methodology uses the reservoir characteristics and an optimization criteria indicated by the engineer, for example a certain propped frac length, and provides the detail of the optimum frac design that will result in the specified criteria. An ensemble of neural networks is trained to mimic the two- or three-dimensional frac simulator. Once successfully trained, these networks are capable of providing instantaneous results in response to any set of input parameters. These

  5. Optimum value of original events on the PEPT technique

    International Nuclear Information System (INIS)

    Sadremomtaz, Alireza; Taherparvar, Payvand

    2011-01-01

    Do Positron emission particle tracking (PEPT) has been used to track the motion of a single radioactively labeled tracer particle within a bed of similar particles. In this paper, the effect of the original event fraction on the results precise in two experiments has been reviewed. Results showed that the algorithm can no longer distinguish some corrupt trajectories, in addition to; further iteration reduces the statistical significance of the sample without improving its quality. Results show that the optimum value of trajectories depends on the type of experiment.

  6. Optimum Value of Original Events on the Pept Technique

    Science.gov (United States)

    Sadremomtaz, Alireza; Taherparvar, Payvand

    2011-12-01

    Do Positron emission particle tracking (PEPT) has been used to track the motion of a single radioactively labeled tracer particle within a bed of similar particles. In this paper, the effect of the original event fraction on the results precise in two experiments has been reviewed. Results showed that the algorithm can no longer distinguish some corrupt trajectories, in addition to; further iteration reduces the statistical significance of the sample without improving its quality. Results show that the optimum value of trajectories depends on the type of experiment.

  7. Design optimum frac jobs using virtual intelligence techniques

    Energy Technology Data Exchange (ETDEWEB)

    Shahab Mohaghegh; Andrei Popa; Sam Ameri [West Virginia University, Morgantown, WV (United States). Petroleum and Natural Gas Engineering

    2000-10-01

    Designing optimal frac jobs is a complex and time-consuming process. It usually involves the use of a two- or three-dimensional computer model. For the computer models to perform as intended, a wealth of input data is required. The input data includes wellbore configuration and reservoir characteristics such as porosity, permeability, stress and thickness profiles of the pay layers as well as the overburden layers. Among other essential information required for the design process is fracturing fluid type and volume, proppant type and volume, injection rate, proppant concentration and frac job schedule. Some of the parameters such as fluid and proppant types have discrete possible choices. Other parameters such as fluid and proppant volume, on the other hand, assume values from within a range of minimum and maximum values. A potential frac design for a particular pay zone is a combination of all of these parameters. Finding the optimum combination is not a trivial process. It usually requires an experienced engineer and a considerable amount of time to tune the parameters in order to achieve desirable outcome. This paper introduces a new methodology that integrates two virtual intelligence techniques, namely, artificial neural networks and genetic algorithms to automate and simplify the optimum frac job design process. This methodology requires little input from the engineer beyond the reservoir characterizations and wellbore configuration. The software tool that has been developed based on this methodology uses the reservoir characteristics and an optimization criteria indicated by the engineer, for example a certain propped frac length, and provides the detail of the optimum frac design that will result in the specified criteria. An ensemble of neural networks is trained to mimic the two- or three-dimensional frac simulator. Once successfully trained, these networks are capable of providing instantaneous results in response to any set of input parameters. These

  8. Optimum commodity taxation with a non-renewable resource

    DEFF Research Database (Denmark)

    Daubanes, Julien Xavier; Lasserre, Pierre

    2017-01-01

    We examine optimum commodity taxation (OCT), including the taxation of non-renewable resources (NRRs), by a government that needs to rely on commodity taxes to raise revenues. NRRs should be taxed at higher rates than otherwise-identical conventional commodities, according to an augmented, dynamic...... formulas can directly be used to indicate how Pigovian taxation of carbon NRRs should be increased in the presence of public-revenue needs, as illustrated in a numerical example. We show that NRR substitutes and complements should receive a particular tax treatment. Finally, in a NRR-importing economy...

  9. Modified loss coefficients in the determination of optimum generation scheduling

    Energy Technology Data Exchange (ETDEWEB)

    Hazarika, D.; Bordoloi, P.K. (Assam Engineering Coll. (IN))

    1991-03-01

    A modified method has been evolved to form the loss coefficients of an electrical power system network by decoupling load and generation and thereby creating additional fictitious load buses. The system losses are then calculated and co-ordinated to arrive at an optimum scheduling of generation using the standard co-ordination equation. The method presented is superior to the ones currently available, in that it is applicable to a multimachine system with random variation of load and it accounts for limits in plant generations and line losses. The precise nature of results and the economy in the cost of energy production obtained by this method is quantified and presented. (author).

  10. Optimum back-pressure forging using servo die cushion

    OpenAIRE

    Kawamoto, Kiichiro; Yoneyama, Takeshi; Okada, Masato; Kitayama, Satoshi; Chikahisa, Junpei

    2014-01-01

    This study focused on utilizing a servo die cushion (in conjunction with a servo press) as a "back-pressure load generator," to determine its effect on shape accuracy of the formed part and total forming load in forward extrusion during cold forging. The effect of back-pressure load application was confirmed in experiments, and the optimum setting pattern of back-pressure load was considered to minimize both shape accuracy of the formed part and back-pressure energy, which was representative ...

  11. Optimum heat storage design for heat integrated multipurpose batch plants

    CSIR Research Space (South Africa)

    Stamp, J

    2011-01-01

    Full Text Available procedure is presented tha journal homepage: www All rights reserved. ajozi T, Optimum heat storage grated multipurpose batch plants , South Africa y usage in multipurpose batch plants has been in published literature most present methods, time... � 2pL?u?kins ? 1 h3A3?u?cu?U (36) The internal area for heat loss by convection from the heat transfer medium is given by Constraint (37) and the area for convective heat transfer losses to the environment is given in Constraint (38). A1?u? ? 2...

  12. Optimum operating conditions for a combined power and cooling thermodynamic cycle

    International Nuclear Information System (INIS)

    Sadrameli, S.M.; Goswami, D.Y.

    2007-01-01

    The combined production of thermal power and cooling with an ammonia-water based cycle proposed by Goswami is under intensive investigation. In the cycle under consideration, simultaneous cooling output is produced by expanding an ammonia-rich vapor in an expander to sub-ambient temperatures and subsequently heating the cool exhaust. When this mechanism for cooling production is considered in detail, it is apparent that the cooling comes at some expense to work production. To optimize this trade-off, a very specific coefficient-of-performance has been defined. In this paper, the simulation of the cycle was carried out in the process simulator ASPEN Plus. The optimum operating conditions have been found by using the Equation Oriented mode of the simulator and some of the results have been compared with the experimental data obtained from the cycle. The agreement between the two sets proves the accuracy of the optimization results

  13. An improved optimum-path forest clustering algorithm for remote sensing image segmentation

    Science.gov (United States)

    Chen, Siya; Sun, Tieli; Yang, Fengqin; Sun, Hongguang; Guan, Yu

    2018-03-01

    Remote sensing image segmentation is a key technology for processing remote sensing images. The image segmentation results can be used for feature extraction, target identification and object description. Thus, image segmentation directly affects the subsequent processing results. This paper proposes a novel Optimum-Path Forest (OPF) clustering algorithm that can be used for remote sensing segmentation. The method utilizes the principle that the cluster centres are characterized based on their densities and the distances between the centres and samples with higher densities. A new OPF clustering algorithm probability density function is defined based on this principle and applied to remote sensing image segmentation. Experiments are conducted using five remote sensing land cover images. The experimental results illustrate that the proposed method can outperform the original OPF approach.

  14. Mode analysis of heuristic behavior of searching for multimodal optimum point

    Energy Technology Data Exchange (ETDEWEB)

    Kamei, K; Araki, Y; Inoue, K

    1982-01-01

    Describes an experimental study of a heuristic behavior of searching for the global optimum (maximum) point of a two-dimensional, multimodal, nonlinear and unknown function. First, the authors define three modes dealing with the trial purposes, called the purpose modes and show the heuristic search behaviors expressed by the purpose modes which the human subjects select in the search experiments. Second, the authors classify the heuristic search behaviors into three types according to the mode transitions and extracts eight states of searches which cause the mode transitions. Third, a model of the heuristic search behavior is composed of the eight mode transitions. The analysis of the heuristic search behaviors by use of the purpose modes plays an important role in the heuristic search techniques. 6 references.

  15. Biomechanical justification of the choice of optimum mode for passing the individual pursuit race

    Directory of Open Access Journals (Sweden)

    A.N. Kolumbet

    2018-04-01

    Full Text Available Purpose : biomechanical justification of the choice of optimum mode of passing competitive distance of 4 km individual pursuit on track. Material : The qualified cyclists (n=14 participated in researches. The modified stationary cycle Monark was used. Cyclists performed work in two modes - A and B. Results : The mode B is physiologically more favorable. The mode B should be considered as a model of passing a distance in preliminary races of individual pursuit. Work in the mode A demands terminal mobilization of organism functions. Work in the mode A is more effective in the achievement of sports result. It can be used only once in the final race of competitions. Conclusions : The received data should be considered as a demonstration of specific features of passing a distance in the competitive modes. The tactical variant of competitive program creation is defined by the individual functional state.

  16. Ultimate Bound of a 3D Chaotic System and Its Application in Chaos Synchronization

    Directory of Open Access Journals (Sweden)

    Jiezhi Wang

    2014-01-01

    Full Text Available Two ellipsoidal ultimate boundary regions of a special three-dimensional (3D chaotic system are proposed. To this chaotic system, the linear coefficient of the ith state variable in the ith state equation has the same sign; it also has two one-order terms and one quadratic cross-product term in each equation. A numerical solution and an analytical expression of the ultimate bounds are received. To get the analytical expression of the ultimate boundary region, a new result of one maximum optimization question is proved. The corresponding ultimate boundary regions are demonstrated through numerical simulations. Utilizing the bounds obtained, a linear controller is proposed to achieve the complete chaos synchronization. Numerical simulation exhibits the feasibility of the designed scheme.

  17. LRFD software for design and actual ultimate capacity of confined rectangular columns.

    Science.gov (United States)

    2013-04-01

    The analysis of concrete columns using unconfined concrete models is a well established practice. On the : other hand, prediction of the actual ultimate capacity of confined concrete columns requires specialized nonlinear : analysis. Modern codes and...

  18. [Deniss Hanovs, Valdis Tēraudkalns: Ultimate Freedom - no choice] / Olaf Mertelsmann

    Index Scriptorium Estoniae

    Mertelsmann, Olaf, 1969-

    2014-01-01

    Arvustus: Deniss Hanovs, Valdis Tēraudkalns: Ultimate Freedom - no choice. The culture of authoritarianism in Latvia, 1934-1940. (Central and Eastern Europe. Reginal perspectives in global context, Bd. 2.) Brill. Leiden-Boston 2013

  19. Reduced design load basis for ultimate blade loads estimation in multidisciplinary design optimization frameworks

    DEFF Research Database (Denmark)

    Pavese, Christian; Tibaldi, Carlo; Larsen, Torben J.

    2016-01-01

    The aim is to provide a fast and reliable approach to estimate ultimate blade loads for a multidisciplinary design optimization (MDO) framework. For blade design purposes, the standards require a large amount of computationally expensive simulations, which cannot be efficiently run each cost...... function evaluation of an MDO process. This work describes a method that allows integrating the calculation of the blade load envelopes inside an MDO loop. Ultimate blade load envelopes are calculated for a baseline design and a design obtained after an iteration of an MDO. These envelopes are computed...... for a full standard design load basis (DLB) and a deterministic reduced DLB. Ultimate loads extracted from the two DLBs with the two blade designs each are compared and analyzed. Although the reduced DLB supplies ultimate loads of different magnitude, the shape of the estimated envelopes are similar...

  20. Optimum Operating Conditions for PZT Actuators for Vibrotactile Wearables

    Science.gov (United States)

    Logothetis, Irini; Matsouka, Dimitra; Vassiliadis, Savvas; Vossou, Clio; Siores, Elias

    2018-04-01

    Recently, vibrotactile wearables have received much attention in fields such as medicine, psychology, athletics and video gaming. The electrical components presently used to generate vibration are rigid; hence, the design and creation of ergonomical wearables are limited. Significant advances in piezoelectric components have led to the production of flexible actuators such as piezoceramic lead zirconate titanate (PZT) film. To verify the functionality of PZT actuators for use in vibrotactile wearables, the factors influencing the electromechanical conversion were analysed and tested. This was achieved through theoretical and experimental analyses of a monomorph clamped-free structure for the PZT actuator. The research performed for this article is a three-step process. First, a theoretical analysis presents the equations governing the actuator. In addition, the eigenfrequency of the film was analysed preceding the experimental section. For this stage, by applying an electric voltage and varying the stimulating electrical characteristics (i.e., voltage, electrical waveform and frequency), the optimum operating conditions for a PZT film were determined. The tip displacement was measured referring to the mechanical energy converted from electrical energy. From the results obtained, an equation for the mechanical behaviour of PZT films as actuators was deduced. It was observed that the square waveform generated larger tip displacements. In conjunction with large voltage inputs at the predetermined eigenfrequency, the optimum operating conditions for the actuator were achieved. To conclude, PZT films can be adapted to assist designers in creating comfortable vibrotactile wearables.

  1. Optimum Tower Crane Selection and Supporting Design Management

    Directory of Open Access Journals (Sweden)

    Hyo Won Sohn

    2014-08-01

    Full Text Available To optimize tower crane selection and supporting design, lifting requirements (as well as stability should be examined, followed by a review of economic feasibility. However, construction engineers establish plans based on data provided by equipment suppliers since there are no tools with which to thoroughly examine a support design's suitability for various crane types, and such plans lack the necessary supporting data. In such cases it is impossible to optimize a tower crane selection to satisfy lifting requirements in terms of cost, and to perform lateral support and foundation design. Thus, this study is intended to develop an optimum tower crane selection and supporting design management method based on stability. All cases that are capable of generating an optimization of approximately 3,000 ˜ 15,000 times are calculated to identify the candidate cranes with minimized cost, which are examined. The optimization method developed in the study is expected to support engineers in determining the optimum lifting equipment management.

  2. Optimum concrete compression strength using bio-enzyme

    Directory of Open Access Journals (Sweden)

    Bagio Tony Hartono

    2017-01-01

    Full Text Available To make concrete with high compressive strength and has a certain concrete specifications other than the main concrete materials are also needed concrete mix quality control and other added material is also in line with the current technology of concrete mix that produces concrete with specific characteristics. Addition of bio enzyme on five concrete mixture that will be compared with normal concrete in order to know the optimum level bio-enzyme in concrete to increase the strength of the concrete. Concrete with bio-enzyme 200 ml/m3, 400 ml/m3, 600 ml/m3, 800 ml/m3, 1000 ml/m3 and normal concrete. Refer to the crushing test result, its tends to the mathematical model using 4th degree polynomial regression (least quartic, as represent on the attached data series, which is for the design mix fc′ = 25 MPa generate optimum value for 33,98 MPa, on the bio-additive dosage of 509 ml bio enzymes.

  3. Carbon sequestration, optimum forest rotation and their environmental impact

    Energy Technology Data Exchange (ETDEWEB)

    Kula, Erhun, E-mail: erhun.kula@bahcesehir.edu.tr [Department of Economics, Bahcesehir University, Besiktas, Istanbul (Turkey); Gunalay, Yavuz, E-mail: yavuz.gunalay@bahcesehir.edu.tr [Department of Business Studies, Bahcesehir University, Besiktas, Istanbul (Turkey)

    2012-11-15

    Due to their large biomass forests assume an important role in the global carbon cycle by moderating the greenhouse effect of atmospheric pollution. The Kyoto Protocol recognises this contribution by allocating carbon credits to countries which are able to create new forest areas. Sequestrated carbon provides an environmental benefit thus must be taken into account in cost-benefit analysis of afforestation projects. Furthermore, like timber output carbon credits are now tradable assets in the carbon exchange. By using British data, this paper looks at the issue of identifying optimum felling age by considering carbon sequestration benefits simultaneously with timber yields. The results of this analysis show that the inclusion of carbon benefits prolongs the optimum cutting age by requiring trees to stand longer in order to soak up more CO{sub 2}. Consequently this finding must be considered in any carbon accounting calculations. - Highlights: Black-Right-Pointing-Pointer Carbon sequestration in forestry is an environmental benefit. Black-Right-Pointing-Pointer It moderates the problem of global warming. Black-Right-Pointing-Pointer It prolongs the gestation period in harvesting. Black-Right-Pointing-Pointer This paper uses British data in less favoured districts for growing Sitka spruce species.

  4. The optimum content of rubber ash in concrete: flexural strength

    Science.gov (United States)

    Senin, M. S.; Shahidan, S.; Shamsuddin, S. M.; Ariffin, S. F. A.; Othman, N. H.; Rahman, R.; Khalid, F. S.; Nazri, F. M.

    2017-11-01

    Discarded scrap tyres have become one of the major environmental problems nowadays. Several studies have been carried out to reuse waste tires as an additive or sand replacement in concrete with appropriate percentages of tire rubber, called as rubberized concrete to solve this problem. The main objectives of this study are to investigate the flexural strength performance of concrete when adding the rubber ash and also to analyse the optimum content of rubber ash in concrete prisms. The performance total of 30 number of concrete prisms in size of 100mm x 100mm x 500 mm were investigated, by partially replacement of rubber ash with percentage of 0%, 3%, 5%, 7% and 9% from the volume of the sand. The flexural strength is increased when percentage of rubber ash is added 3% from control concrete prism, RA 0 for both concrete prism age, 7 days and 28 days with value 1.21% and 0.976% respectively. However, for RA 5, RA 7 and RA 9, the flexural strength was decreased compared to the control for both age, 7 days and 28 days. In conclusion, 3% is the optimum content of rubber ash in concrete prism for both concrete age

  5. Determination of the Optimum Conditions for Production of Chitosan Nanoparticles

    Directory of Open Access Journals (Sweden)

    A. Dustgani

    2007-12-01

    Full Text Available Bioedegradable nanoparticles are intensively investigated for their potential applications in drug delivery systems. Being a biocompatible and biodegradable polymer, chitosan holds great promise for use in this area. This investigation was concerned with determination and optimization of the effective parameters involved in the production of chitosan nanoparticles using ionic gelation method. Studied variables were concentration and pH of the chitosan solution, the ratio of chitosan to sodium tripolyphosphate therein and the molecular weight of chitosan. For this purpose, Taguchistatistical method was used for design of experiments in three levels. The size of chitosan nanoparticle was determined using laser light scattering. The experimental results showed that concentration of chitosan solution was the most important parameter and chitosan molecular weight the least effective parameter. The optimum conditions for preparation of nanoparticles were found to be 1 mg/mL chitosan solution with pH=5, chitosan to sodium tripolyphosphate ratio of 3 and chitosan molecular weight of 200,000 daltons. The average nanoparticle size at optimum conditions was found to be about 150 nm.

  6. Optimum distributed generation placement with voltage sag effect minimization

    International Nuclear Information System (INIS)

    Biswas, Soma; Goswami, Swapan Kumar; Chatterjee, Amitava

    2012-01-01

    Highlights: ► A new optimal distributed generation placement algorithm is proposed. ► Optimal number, sizes and locations of the DGs are determined. ► Technical factors like loss, voltage sag problem are minimized. ► The percentage savings are optimized. - Abstract: The present paper proposes a new formulation for the optimum distributed generator (DG) placement problem which considers a hybrid combination of technical factors, like minimization of the line loss, reduction in the voltage sag problem, etc., and economical factors, like installation and maintenance cost of the DGs. The new formulation proposed is inspired by the idea that the optimum placement of the DGs can help in reducing and mitigating voltage dips in low voltage distribution networks. The problem is configured as a multi-objective, constrained optimization problem, where the optimal number of DGs, along with their sizes and bus locations, are simultaneously obtained. This problem has been solved using genetic algorithm, a traditionally popular stochastic optimization algorithm. A few benchmark systems radial and networked (like 34-bus radial distribution system, 30 bus loop distribution system and IEEE 14 bus system) are considered as the case study where the effectiveness of the proposed algorithm is aptly demonstrated.

  7. Impacts of optimum cost effective energy efficiency standards

    International Nuclear Information System (INIS)

    Brancic, A.B.; Peters, J.S.; Arch, M.

    1991-01-01

    Building Codes are increasingly required to be responsive to social and economic policy concerns. In 1990 the State of Connecticut passes An Act Concerning Global Warming, Public Act 90-219, which mandates the revision of the state building code to require that buildings and building elements be designed to provide optimum cost-effective energy efficiency over the useful life of the building. Further, such revision must meet the American Society of Heating, Refrigerating and Air Conditioning Engineers (ASHRAE) Standard 90.1 - 1989. As the largest electric energy supplier in Connecticut, Northeast Utilities (NU) sponsored a pilot study of the cost effectiveness of alternative building code standards for commercial construction. This paper reports on this study which analyzed design and construction means, building elements, incremental construction costs, and energy savings to determine the optimum cost-effective building code standard. Findings are that ASHRAE 90.1 results in 21% energy savings and alternative standards above it result in significant additional savings. Benefit/cost analysis showed that both are cost effective

  8. Optimum dietary protein requirement of Malaysian mahseer (Tor tambroides) fingerling.

    Science.gov (United States)

    Misieng, Josephine Dorin; Kamarudin, Mohd Salleh; Musa, Mazlinda

    2011-02-01

    The optimum dietary protein requirement of the Malaysian mahseer (Tor tambroides) fingerlings was determined in this study. In this completely randomized designed experiment, formulated diets of five levels of dietary protein (30, 35, 40, 45 and 50%) were tested on the T. tambroides fingerlings (initial body weight of 5.85 +/- 0.40 g), reared in aquarium fitted with a biofiltering system. The fingerlings were fed twice daily at 5% of biomass. The fingerling body weight and total length was taken at every two weeks. Mortality was recorded daily. The dietary protein had significant effects on the body weight gain and Specific Growth Rate (SGR) of the fingerlings. The body weight gain and SGR of fingerlings fed with the diet with the dietary protein level of 40% was significantly higher (p<0.05) than that of 30, 35 and 50%. The feed conversion ratio of the 40% dietary protein was the significantly lowest at 2.19 +/- 0.163. The dietary protein level of 40% was the most optimum for T. tambroides fingerlings.

  9. Carbon sequestration, optimum forest rotation and their environmental impact

    International Nuclear Information System (INIS)

    Kula, Erhun; Gunalay, Yavuz

    2012-01-01

    Due to their large biomass forests assume an important role in the global carbon cycle by moderating the greenhouse effect of atmospheric pollution. The Kyoto Protocol recognises this contribution by allocating carbon credits to countries which are able to create new forest areas. Sequestrated carbon provides an environmental benefit thus must be taken into account in cost–benefit analysis of afforestation projects. Furthermore, like timber output carbon credits are now tradable assets in the carbon exchange. By using British data, this paper looks at the issue of identifying optimum felling age by considering carbon sequestration benefits simultaneously with timber yields. The results of this analysis show that the inclusion of carbon benefits prolongs the optimum cutting age by requiring trees to stand longer in order to soak up more CO 2 . Consequently this finding must be considered in any carbon accounting calculations. - Highlights: ► Carbon sequestration in forestry is an environmental benefit. ► It moderates the problem of global warming. ► It prolongs the gestation period in harvesting. ► This paper uses British data in less favoured districts for growing Sitka spruce species.

  10. Optimum energies for dual-energy computed tomography

    International Nuclear Information System (INIS)

    Talbert, A.J.; Brooks, R.A.; Morgenthaler, D.G.

    1980-01-01

    By performing a dual-energy scan, separate information can be obtained on the Compton and photoelectric components of attenuation for an unknown material. This procedure has been analysed for the optimum energies, and for the optimum dose distribution between the two scans. It was found that an equal dose at both energies was a good compromise, compared with optimising the dose distributing for either the Compton or photoelectric components individually. For monoenergetic beams, it was found that low energy of 40 keV produced minimum noise when using high-energy beams of 80 to 100 keV. This was true whether one maintained constant integral dose or constant surface dose. A low energy of 50 keV which is more nearly attainable in practice, produced almost as good a degree of accuracy. The analysis can be extended to polyenergetic beams by the inclusion of a noise factor. The above results were qualitatively unchanged, although the noise was increased by about 20% with integral dose equivalence and 50% with surface dose equivalence. It is very important to make the spectra as narrow as possible, especially at the low energy, in order to minimise the noise. (author)

  11. Optimum Discharge Burnup and Cycle Length for PWRs

    International Nuclear Information System (INIS)

    Secker, Jeffrey R.; Johansen, Baard J.; Stucker, David L.; Ozer, Odelli; Ivanov, Kostadin; Yilmaz, Serkan; Young, E.H.

    2005-01-01

    This paper discusses the results of a pressurized water reactor fuel management study determining the optimum discharge burnup and cycle length. A comprehensive study was performed considering 12-, 18-, and 24-month fuel cycles over a wide range of discharge burnups. A neutronic study was performed followed by an economic evaluation. The first phase of the study limited the fuel enrichments used in the study to 235 U consistent with constraints today. The second phase extended the range of discharge burnups for 18-month cycles by using fuel enriched in excess of 5 wt%. The neutronic study used state-of-the-art reactor physics methods to accurately determine enrichment requirements. Energy requirements were consistent with today's high capacity factors (>98%) and short (15-day) refueling outages. The economic evaluation method considers various component costs including uranium, conversion, enrichment, fabrication and spent-fuel storage costs as well as the effect of discounting of the revenue stream. The resulting fuel cycle costs as a function of cycle length and discharge burnup are presented and discussed. Fuel costs decline with increasing discharge burnup for all cycle lengths up to the maximum discharge burnup considered. The choice of optimum cycle length depends on assumptions for outage costs

  12. Recommendation for basis for decision on a Danish ultimate storage for low and intermediate radioactive wastes

    International Nuclear Information System (INIS)

    2006-12-01

    In 2003 the Danish Parliament consented to let the government start the preparation of a basis for decision on a Danish ultimate storage for low and intermediate radioactive wastes. The present report is the result of the preparation process, and it describes the fundamental safety and environmental principles for establishing an ultimate storage, including determining the principles for the site selection, storage construction, and safety analyses. (LN)

  13. A Technique for Temperature and Ultimate Load Calculations of Thin Targets in a Pulsed Electron Beam

    DEFF Research Database (Denmark)

    Hansen, Jørgen-Walther; Lundsager, Per

    1979-01-01

    A technique is presented for the calculation of transient temperature distributions and ultimate load of rotationally symmetric thin membranes with uniform lateral load and exposed to a pulsed electron beam from a linear accelerator. Heat transfer by conduction is considered the only transfer...... mechanism. The ultimate load is calculated on the basis of large plastic strain analysis. Analysis of one aluminum and one titanium membrane is shown....

  14. Excess glycogen does not resolve high ultimate pH of oxidative muscle.

    Science.gov (United States)

    England, Eric M; Matarneh, Sulaiman K; Oliver, Emily M; Apaoblaza, Ariel; Scheffler, Tracy L; Shi, Hao; Gerrard, David E

    2016-04-01

    Skeletal muscle glycogen content can impact the extent of postmortem pH decline. Compared to glycolytic muscles, oxidative muscles contain lower glycogen levels antemortem which may contribute to the higher ultimate pH. In an effort to explore further the participation of glycogen in postmortem metabolism, we postulated that increasing the availability of glycogen would drive additional pH decline in oxidative muscles to equivalent pH values similar to the ultimate pH of glycolytic muscles. Glycolysis and pH declines were compared in porcine longissimus lumborum (glycolytic) and masseter (oxidative) muscles using an in vitro system in the presence of excess glycogen. The ultimate pH of the system containing longissimus lumborum reached a value similar to that observed in intact muscle. The pH decline of the system containing masseter samples stopped prematurely resulting in a higher ultimate pH which was similar to that of intact masseter muscle. To investigate further, we titrated powdered longissimus lumborum and masseter samples in the reaction buffer. As the percentage of glycolytic sample increased, the ultimate pH decreased. These data show that oxidative muscle produces meat with a high ultimate pH regardless of glycogen content and suggest that inherent muscle factors associated with glycolytic muscle control the extent of pH decline in pig muscles. Copyright © 2015 Elsevier Ltd. All rights reserved.

  15. Assessment on Ultimate Load of Cold-formed Steel Channel (CFSC Stub Column

    Directory of Open Access Journals (Sweden)

    Mohd Sani Mohd Syahrul Hisyam

    2015-01-01

    Full Text Available Cold-formed steel is used as the non-structural and structural material in civil engineering work and building. Cold-formed steel channel is selected and cut into 100 mm, 200 mm, 300 mm, 400 mm and 500 mm. The slenderness ratio is calculated and noted as a stub or short column because below 40. The column is tested by using Universal Testing Machine to determine the ultimate load of the stub column. Besides, the CFSC is determined the material properties of CFSC for checking it’s the originality of steel based material. The experimental data are tested and compared with the Direct Strength Method (DSM. It showed that the CFSC1 with a height of 100 mm is reported to have a higher value of ultimate load when compared with other samples. When the height of the stub column increased, the ultimate load of the sample is decreased. Then, the CFSC1 also showed a higher in initial stiffness when compared with other samples. All samples are shown having a higher data in ultimate load when compared with the Direct Strength Method prediction. The ultimate load of experimental and DSM all gave a ratio below 1.03. Finally, all samples can further recommend determining the relation between the ultimate loads with variations of height of the column.

  16. Optimum community energy storage system for demand load shifting

    International Nuclear Information System (INIS)

    Parra, David; Norman, Stuart A.; Walker, Gavin S.; Gillott, Mark

    2016-01-01

    Highlights: • PbA-acid and lithium-ion batteries are optimised up to a 100-home community. • A 4-period real-time pricing and Economy 7 (2-period time-of-use) are compared. • Li-ion batteries perform worse with Economy 7 for small communities and vice versa. • The community approach reduced the levelised cost by 56% compared to a single home. • Heat pumps reduced the levelised cost and increased the profitability of batteries. - Abstract: Community energy storage (CES) is becoming an attractive technological option to facilitate the use of distributed renewable energy generation, manage demand loads and decarbonise the residential sector. There is strong interest in understanding the techno-economic benefits of using CES systems, which energy storage technology is more suitable and the optimum CES size. In this study, the performance including equivalent full cycles and round trip efficiency of lead-acid (PbA) and lithium-ion (Li-ion) batteries performing demand load shifting are quantified as a function of the size of the community using simulation-based optimisation. Two different retail tariffs are compared: a time-of-use tariff (Economy 7) and a real-time-pricing tariff including four periods based on the electricity prices on the wholesale market. Additionally, the economic benefits are quantified when projected to two different years: 2020 and a hypothetical zero carbon year. The findings indicate that the optimum PbA capacity was approximately twice the optimum Li-ion capacity in the case of the real-time-pricing tariff and around 1.6 times for Economy 7 for any community size except a single home. The levelised cost followed a negative logarithmic trend while the internal rate of return followed a positive logarithmic trend as a function of the size of the community. PbA technology reduced the levelised cost down to 0.14 £/kW h when projected to the year 2020 for the retail tariff Economy 7. CES systems were sized according to the demand load and

  17. Optimum regulation of grid monopoly in the power trade

    International Nuclear Information System (INIS)

    Hope, E.

    1994-06-01

    The report discusses the organization and behaviour of grid monopolies in the Norwegian power trade and relations to the socio-economic effectiveness. The main attention is laid on analyzing regulation mechanisms and measures leading to an efficient short-term operation and to the investment of optimum production capacity in a long run. Regarding the management, measures are discussed for increasing the efficiency of total power trade by evaluating the existing marketing function of Statnett. Some basic conditions are accounted concerning the regulation problem of grid monopolies with a particular attention to asymmetric information between the authority and the monopoly. In addition, forms of regulation and regulation mechanisms together with the incentive characteristics of these, are discussed. The existing profit regulation principles in relation to an alternative system design such as maximum price regulation combined with standard regulation, are evaluated. 16 refs., 7 figs

  18. Optimum investment strategy in the power industry mathematical models

    CERN Document Server

    Bartnik, Ryszard; Hnydiuk-Stefan, Anna

    2016-01-01

    This book presents an innovative methodology for identifying optimum investment strategies in the power industry. To do so, it examines results including, among others, the impact of oxy-fuel technology on CO2 emissions prices, and the specific cost of electricity production. The technical and economic analysis presented here extend the available knowledge in the field of investment optimization in energy engineering, while also enabling investors to make decisions involving its application. Individual chapters explore the potential impacts of different factors like environmental charges on costs connected with investments in the power sector, as well as discussing the available technologies for heat and power generation. The book offers a valuable resource for researchers, market analysts, decision makers, power engineers and students alike.

  19. Optimum Choice of RF Frequency for Two Beam Linear Colliders

    CERN Document Server

    Braun, Hans Heinrich

    2003-01-01

    Recent experimental results on normal conducting RF structures indicate that the scaling of the gradient limit with frequency is less favourable than what was believed. We therefore reconsider the optimum choice of RF frequency and iris aperture for a normal conducting, two-beam linear collider with E_CMS=3 TeV, a loaded accelerating gradient of 150 MV/m and a luminosity of 8 10^34 cm-^2 s^-1. The optimisation criterion is minimizing overall RF costs for investment and operation with constraints put on peak surface electric fields and pulsed heating of accelerating structures. Analytical models are employed where applicable, while interpolation on simulation program results is used for the calculation of luminosity and RF structure properties.

  20. Kernel Optimum Nearly-analytical Discretization (KOND) algorithm

    International Nuclear Information System (INIS)

    Kondoh, Yoshiomi; Hosaka, Yasuo; Ishii, Kenji

    1992-10-01

    Two applications of the Kernel Optimum Nearly-analytical Discretization (KOND) algorithm to the parabolic- and the hyperbolic type equations a presented in detail to lead to novel numerical schemes with very high numerical accuracy. It is demonstrated numerically that the two dimensional KOND-P scheme for the parabolic type yields quite less numerical error by over 2-3 orders and reduces the CPU time to about 1/5 for a common numerical accuracy, compared with the conventional explicit scheme of reference. It is also demonstrated numerically that the KOND-H scheme for the hyperbolic type yields fairly less diffusive error and has fairly high stability for both of the linear- and the nonlinear wave propagations compared with other conventional schemes. (author)

  1. Problems in the optimum display of SPECT images

    International Nuclear Information System (INIS)

    Fielding, S.L.

    1988-01-01

    The instrumentation, computer hardware and software, and the image display system are all very important in the production of diagnostically useful SPECT images. Acquisition and processing parameters are discussed which can affect the quality of SPECT images. Regular quality control of the gamma camera and computer is important to keep the artifacts due to instrumentation to a minimum. The choice of reconstruction method will depend on the statistics in the study. The paper has shown that for high count rate studies, a high pass filter can be used to enhance the reconstructions. For lower count rate studies, pre-filtering is useful and the data can be reconstructed into thicker slices to reduce the effect of image noise. Finally, the optimum display for the images must be chosen, so that the information contained in the SPECT data can be easily perceived by the clinician. (orig.) [de

  2. A Decision Support System for Optimum Use of Fertilizers

    Energy Technology Data Exchange (ETDEWEB)

    R. L. Hoskinson; J. R. Hess; R. K. Fink

    1999-07-01

    The Decision Support System for Agriculture (DSS4Ag) is an expert system being developed by the Site-Specific Technologies for Agriculture (SST4Ag) precision farming research project at the INEEL. DSS4Ag uses state-of-the-art artificial intelligence and computer science technologies to make spatially variable, site-specific, economically optimum decisions on fertilizer use. The DSS4Ag has an open architecture that allows for external input and addition of new requirements and integrates its results with existing agricultural systems' infrastructures. The DSS4Ag reflects a paradigm shift in the information revolution in agriculture that is precision farming. We depict this information revolution in agriculture as an historic trend in the agricultural decision-making process.

  3. A Decision Support System for Optimum Use of Fertilizers

    Energy Technology Data Exchange (ETDEWEB)

    Hoskinson, Reed Louis; Hess, John Richard; Fink, Raymond Keith

    1999-07-01

    The Decision Support System for Agriculture (DSS4Ag) is an expert system being developed by the Site-Specific Technologies for Agriculture (SST4Ag) precision farming research project at the INEEL. DSS4Ag uses state-of-the-art artificial intelligence and computer science technologies to make spatially variable, site-specific, economically optimum decisions on fertilizer use. The DSS4Ag has an open architecture that allows for external input and addition of new requirements and integrates its results with existing agricultural systems’ infrastructures. The DSS4Ag reflects a paradigm shift in the information revolution in agriculture that is precision farming. We depict this information revolution in agriculture as an historic trend in the agricultural decision-making process.

  4. Narratives of Optimum Currency Area theory and Eurozone Governance

    DEFF Research Database (Denmark)

    Snaith, Holly Grace

    2014-01-01

    is the subject of very significant internal disagreement, to the extent that economists writing within the field do not commonly agree upon the ontological foundations of the theory. This entails that the translation of the theory into political reality has been characterised by a series of often mutually...... contradictory narratives, which build upon schisms in the academic corpus. The political realisation of this can be seen during the negotiations over the 1992 process, where certain aspects of the theory concerning governance (of fiscal policy and preferences for conflict adjudication) have been notably......Optimum Currency Area theory (OCA) is a body of research that has, since its inception in 1961, been highly influential for the discourse and design of Economic and Monetary Union, exercising a significant hermeneutical force. Nonetheless, there has been little acknowledgement that OCA...

  5. Optimum conditions for aging of stainless maraging steels

    International Nuclear Information System (INIS)

    Mironenko, P.A.; Krasnikova, S.I.; Drobot, A.V.

    1980-01-01

    Aging kinetics of two 0Kh11N10M2T type steels in which 3 % Mo (steel 1), and 3 % Mo and 11 % Co (steel 2) had been additionally introduced instead of titanium were investigated. Electron microscopy and X-ray methods were used. It was ascertained that the process of steel aging proceeded in 3 stages. Steel 2 was hardened more intensively during the aging, had a higher degree of hardness and strength after the aging, weakened more slowly if overaged than steel 1. The intermetallide hcp-phase Fe 2 Mo was the hardening phase on steels extended aging. Optimum combination of impact strength and strength was was achieved using two-stage aging: the first stage - maximum strength aging was achieved, the second stage - aging at minimum temperatures of two-phase α+γ region

  6. Testing Optimum Seeding Rates for five Bread Wheat Cultivars

    International Nuclear Information System (INIS)

    Wekesa, S.J.; Kiriswa, F.; Owuoche, J.

    1999-01-01

    A cultivar by seed rate trial was conducted in 1994-1995 crop seasons at Njoro, Kenya. Yield results were found to be significant (P > 0.01) for year, variety, seed rate and year by seed rate interaction. Test weight was highly significant (P -1 were grouped together for significantly higher yields (A) whereas seed rates 85 and 50 kg ha -1 had lower significant yields (B and C respectively). The same grouping was repeated for test weight. There was no significant cultivar by seed rate interaction and no cultivar, specific seed rate. However, since seed rates 245, 205, 165 and 125 kg ha -1 were grouped together, the lowest seed rate, 125 kg ha -1 can be recommended as the optimum seed rate for the above cultivars, as higher seed rates do not give significantly higher yields or higher test weights

  7. Optimum design of band-gap beam structures

    DEFF Research Database (Denmark)

    Olhoff, Niels; Niu, Bin; Cheng, Gengdong

    2012-01-01

    The design of band-gap structures receives increasing attention for many applications in mitigation of undesirable vibration and noise emission levels. A band-gap structure usually consists of a periodic distribution of elastic materials or segments, where the propagation of waves is impeded...... or significantly suppressed for a range of external excitation frequencies. Maximization of the band-gap is therefore an obvious objective for optimum design. This problem is sometimes formulated by optimizing a parameterized design model which assumes multiple periodicity in the design. However, it is shown...... in the present paper that such an a priori assumption is not necessary since, in general, just the maximization of the gap between two consecutive natural frequencies leads to significant design periodicity. The aim of this paper is to maximize frequency gaps by shape optimization of transversely vibrating...

  8. Optimum energy management of a photovoltaic water pumping system

    International Nuclear Information System (INIS)

    Sallem, Souhir; Chaabene, Maher; Kamoun, M.B.A.

    2009-01-01

    This paper presents a new management approach which makes decision on the optimum connection times of the elements of a photovoltaic water pumping installation: battery, water pump and photovoltaic panel. The decision is made by fuzzy rules considering the battery safety on the first hand and the Photovoltaic Panel Generation (PVPG) forecast during a considered day and the load required power on the second hand. The optimization approach consists of the extension of the operation time of the water pump with respects to multi objective management criteria. Compared to the stand alone management method, the new approach effectiveness is confirmed by the extension of the pumping period for more than 5 h a day.

  9. Optimum hot water temperature for absorption solar cooling

    Energy Technology Data Exchange (ETDEWEB)

    Lecuona, A.; Ventas, R.; Venegas, M.; Salgado, R. [Dpto. Ingenieria Termica y de Fluidos, Universidad Carlos III de Madrid, Avda. Universidad 30, 28911 Leganes, Madrid (Spain); Zacarias, A. [ESIME UPA, IPN, Av. de las Granjas 682, Col. Santa Catarina, 02550, D.F. Mexico (Mexico)

    2009-10-15

    The hot water temperature that maximizes the overall instantaneous efficiency of a solar cooling facility is determined. A modified characteristic equation model is used and applied to single-effect lithium bromide-water absorption chillers. This model is based on the characteristic temperature difference and serves to empirically calculate the performance of real chillers. This paper provides an explicit equation for the optimum temperature of vapor generation, in terms of only the external temperatures of the chiller. The additional data required are the four performance parameters of the chiller and essentially a modified stagnation temperature from the detailed model of the thermal collector operation. This paper presents and discusses the results for small capacity machines for air conditioning of homes and small buildings. The discussion highlights the influence of the relevant parameters. (author)

  10. Optimum Identification Method of Sorting Green Household Waste

    Directory of Open Access Journals (Sweden)

    Daud Mohd Hisam

    2016-01-01

    Full Text Available This project is related to design of sorting facility for reducing, reusing, recycling green waste material, and in particular to invent an automatic system to distinguish household waste in order to separate them from the main waste stream. The project focuses on thorough analysis of the properties of green household waste. The method of identification is using capacitive sensor where the characteristic data taken on three different sensor drive frequency. Three types of material have been chosen as a medium of this research, to be separated using the selected method. Based on capacitance characteristics and its ability to penetrate green object, optimum identification method is expected to be recognized in this project. The output capacitance sensor is in analogue value. The results demonstrate that the information from the sensor is enough to recognize the materials that have been selected.

  11. Constraint-Based Local Search for Constrained Optimum Paths Problems

    Science.gov (United States)

    Pham, Quang Dung; Deville, Yves; van Hentenryck, Pascal

    Constrained Optimum Path (COP) problems arise in many real-life applications and are ubiquitous in communication networks. They have been traditionally approached by dedicated algorithms, which are often hard to extend with side constraints and to apply widely. This paper proposes a constraint-based local search (CBLS) framework for COP applications, bringing the compositionality, reuse, and extensibility at the core of CBLS and CP systems. The modeling contribution is the ability to express compositional models for various COP applications at a high level of abstraction, while cleanly separating the model and the search procedure. The main technical contribution is a connected neighborhood based on rooted spanning trees to find high-quality solutions to COP problems. The framework, implemented in COMET, is applied to Resource Constrained Shortest Path (RCSP) problems (with and without side constraints) and to the edge-disjoint paths problem (EDP). Computational results show the potential significance of the approach.

  12. Environmental Planning Strategies for Optimum Solid Waste Landfill Siting

    International Nuclear Information System (INIS)

    Sumiani, Y.; Onn, C.C.; Mohd, M.A.D.; Wan, W.Z.J.

    2009-01-01

    The use of environmental planning tools for optimum solid waste landfill siting taking into account all environmental implications was carried out by applying Life Cycle Analysis (LCA) to enhance the research information obtained from initial analysis using Geographical Information Systems (GIS). The objective of this study is to identify the most eco-friendly landfill site by conducting a LCA analysis upon 5 potential GIS generated sites which incorporated eleven important criteria related to the social, environmental, and economical factors. The LCA analysis utilized the daily distance covered by collection trucks among the 5 selected landfill sites to generate inventory data on total energy usage for each landfill sites. The planning and selection of the potential sites were facilitated after conducting environmental impact analysis upon the inventory data which showed the least environmental impact. (author)

  13. Optimum Actuator Selection with a Genetic Algorithm for Aircraft Control

    Science.gov (United States)

    Rogers, James L.

    2004-01-01

    The placement of actuators on a wing determines the control effectiveness of the airplane. One approach to placement maximizes the moments about the pitch, roll, and yaw axes, while minimizing the coupling. For example, the desired actuators produce a pure roll moment without at the same time causing much pitch or yaw. For a typical wing, there is a large set of candidate locations for placing actuators, resulting in a substantially larger number of combinations to examine in order to find an optimum placement satisfying the mission requirements and mission constraints. A genetic algorithm has been developed for finding the best placement for four actuators to produce an uncoupled pitch moment. The genetic algorithm has been extended to find the minimum number of actuators required to provide uncoupled pitch, roll, and yaw control. A simplified, untapered, unswept wing is the model for each application.

  14. Optimum fuel allocation in parallel steam generator systems

    International Nuclear Information System (INIS)

    Bollettini, U.; Cangioli, E.; Cerri, G.; Rome Univ. 'La Sapienza'; Trento Univ.

    1991-01-01

    An optimization procedure was developed to allocate fuels into parallel steam generators. The procedure takes into account the level of performance deterioration connected with the loading history (fossil fuel allocation and maintenance) of each steam generator. The optimization objective function is the system hourly cost, overall steam demand being satisfied. Costs are due to fuel and electric power supply and to plant depreciation and maintenance as well. In order to easily updata the state of each steam generator, particular care was put in the general formulation of the steam production function by adopting a special efficiency-load curve description based on a deterioration scaling parameter. The influence of the characteristic time interval length on the optimum operation result is investigated. A special implementation of the method based on minimum cost paths is suggested

  15. Optimum radars and filters for the passive sphere system

    Science.gov (United States)

    Luers, J. K.; Soltes, A.

    1971-01-01

    Studies have been conducted to determine the influence of the tracking radar and data reduction technique on the accuracy of the meteorological measurements made in the 30 to 100 kilometer altitude region by the ROBIN passive falling sphere. A survey of accuracy requirements was made of agencies interested in data from this region of the atmosphere. In light of these requirements, various types of radars were evaluated to determine the tracking system most applicable to the ROBIN, and methods were developed to compute the errors in wind and density that arise from noise errors in the radar supplied data. The effects of launch conditions on the measurements were also examined. Conclusions and recommendations have been made concerning the optimum tracking and data reduction techniques for the ROBIN falling sphere system.

  16. The optimum functionalization of carbon nanotube/ferritin composites

    International Nuclear Information System (INIS)

    Lee, Ji Won; Shin, Kwang Min; Kim, Seon Jeong; Lynam, Carol; Spinks, Geoffrey M; Wallace, Gordon G

    2008-01-01

    We fabricated a covalently linked composite composed of functionalized single-walled carbon nanotubes (f-SWNT) and ferritin protein as nanoparticles. The various f-SWNTs were prepared using an acid treatment of purified SWNT for different functionalization times (30, 60, 120 and 180 min), and ferritin was immobilized on each of the f-SWNT by covalent immobilization. The specific capacitance of the f-SWNT and the electrochemical activity of the f-SWNT/ferritin composites showed a Gaussian distribution. From the electrochemical analysis, the ferritin composite with functionalized SWNT for 60 min showed the highest capacitance and electrochemical activity than other f-SWNT/ferritin composites. This result suggests the optimum value for the best performance of the electrochemical properties of f-SWNT/ferritin composites was found for a potential bioapplication

  17. Optimum selection of an energy resource using fuzzy logic

    International Nuclear Information System (INIS)

    Abouelnaga, Ayah E.; Metwally, Abdelmohsen; Nagy, Mohammad E.; Agamy, Saeed

    2009-01-01

    Optimum selection of an energy resource is a vital issue in developed countries. Considering energy resources as alternatives (nuclear, hydroelectric, gas/oil, and solar) and factors upon which the proper decision will be taken as attributes (economics, availability, environmental impact, and proliferation), one can use the multi-attribute utility theory (MAUT) to optimize the selection process. Recently, fuzzy logic is extensively applied to the MAUT as it expresses the linguistic appraisal for all attributes in wide and reliable manners. The rise in oil prices and the increased concern about environmental protection from CO 2 emissions have promoted the attention to the use of nuclear power as a viable energy source for power generation. For Egypt, as a case study, the nuclear option is found to be an appropriate choice. Following the introduction of innovative designs of nuclear power plants, improvements in the proliferation resistance, environmental impacts, and economics will enhance the selection of the nuclear option.

  18. The optimum choice of gate width for neutron coincidence counting

    Energy Technology Data Exchange (ETDEWEB)

    Croft, S., E-mail: crofts@ornl.gov [Safeguards and Security Technology (SST), Global Nuclear Security Technology Divisions, PO Box 2008, Building 5700, MS-6166, Oak Ridge, TN 37831-6166 (United States); Henzlova, D.; Favalli, A.; Hauck, D.K.; Santi, P.A. [Safeguards Science and Technology Group (NEN-1), Nuclear Engineering and Nonproliferation Division, MS-E540, Los Alamos, NM 87545 (United States)

    2014-11-11

    In the measurement field of international nuclear safeguards, passive neutron coincidence counting is used to quantify the spontaneous fission rate of certain special nuclear materials. The shift register autocorrelation analysis method is the most commonly used approach. However, the Feynman-Y technique, which is more commonly applied in reactor noise analysis, provides an alternative means to extract the correlation information from a pulse train. In this work we consider how to select the optimum gate width for each of these two time-correlation analysis techniques. The optimum is considered to be that which gives the lowest fractional precision on the net doublets rate. Our theoretical approach is approximate but is instructional in terms of revealing the key functional dependence. We show that in both cases the same performance figure of merit applies so that common design criteria apply to the neutron detector head. Our prediction is that near optimal results, suitable for most practical applications, can be obtained from both techniques using a common gate width setting. The estimated precision is also comparable in the two cases. The theoretical expressions are tested experimentally using {sup 252}Cf spontaneous fission sources measured in two thermal well counters representative of the type in common use by international inspectorates. Fast accidental sampling was the favored method of acquiring the Feynman-Y data. Our experimental study confirmed the basic functional dependences predicted although experimental results when available are preferred. With an appropriate gate setting Feynman-Y analysis provides an alternative to shift register analysis for safeguards applications which is opening up new avenues of data collection and data reduction to explore.

  19. Optimum design of cogeneration system for nuclear seawater desalination - 15272

    International Nuclear Information System (INIS)

    Jung, Y.H.; Jeong, Y.H.

    2015-01-01

    A nuclear desalination process, which uses the energy released by nuclear fission, has less environmental impact and is generally cost-competitive with a fossil-fuel desalination process. A reference cogeneration system focused on in this study is the APR-1400 coupled with a MED (multi-effect distillation) process using the thermal vapor compression (TVC) technology. The thermal condition of the heat source is the most crucial factor that determines the desalination performance, i.e. energy consumption or freshwater production, of the MED-TVC process. The MED-TVC process operating at a higher motive steam pressure clearly shows a higher desalination performance. However, this increased performance does not necessarily translate to an advantage over processes operated at lower motive steam pressures. For instance, a higher motive steam pressure will increase the heat cost resulting from larger electricity generation loss, and thus may make this process unfavorable from an economic point of view. Therefore, there exists an optimum design point in the coupling configuration that makes the nuclear cogeneration system the most economical. This study is mainly aimed at investigating this optimum coupling design point of the reference nuclear cogeneration system using corresponding analysis tools. The following tools are used: MEE developed by the MEDRC for desalination performance analysis of the MED-TVC process, DE-TOP and DEEP developed by the IAEA for modeling of coupling configuration and economic evaluation of the nuclear cogeneration system, respectively. The results indicate that steam extraction from the MS exhaust and condensate return to HP FWHTR 5 is the most economical coupling design

  20. The optimum tension for bridging sutures in transosseous-equivalent rotator cuff repair: a cadaveric biomechanical study.

    Science.gov (United States)

    Park, Ji Soon; McGarry, Michelle H; Campbell, Sean T; Seo, Hyuk Jun; Lee, Yeon Soo; Kim, Sae Hoon; Lee, Thay Q; Oh, Joo Han

    2015-09-01

    Transosseous-equivalent (TOE) rotator cuff repair can increase contact area and contact pressure between the repaired cuff tendon and bony footprint and can show higher ultimate loads to failure and smaller gap formation compared with other repair techniques. However, it has been suggested that medial rotator cuff failure after TOE repair may result from increased bridging suture tension. To determine optimum bridging suture tension in TOE repair by evaluating footprint contact and construct failure characteristics at different tensions. Controlled laboratory study. A total of 18 fresh-frozen cadaveric shoulders, randomly divided into 3 groups, were constructed with a TOE configuration using the same medial suture anchor and placing a Tekscan sensing pad between the repaired rotator cuff tendon and footprint. Nine of the 18 shoulders were used to measure footprint contact characteristics. With use of the Tekscan measurement system, the contact pressure and area between the rotator cuff tendon and greater tuberosity were quantified for bridging suture tensions of 60, 90, and 120 N with glenohumeral abduction angles of 0° and 30° and humeral rotation angles of 30° (internal), 0°, and 30° (external). TOE constructs of all 18 shoulders then underwent construct failure testing (cyclic loading and load to failure) to determine the yield load, ultimate load, stiffness, hysteresis, strain, and failure mode at 60 and 120 N of tension. As bridging suture tension increased, contact force, contact pressure, and peak pressure increased significantly at all positions (P .05 for all). Increasing bridging suture tension to over 90 N did not improve contact area but did increase contact force and pressure. Bridging suture tension did not significantly affect ultimate failure loads. Considering the risks of overtensioning bridging sutures, it may be clinically more beneficial to keep bridging suture tension below 90 N. © 2015 The Author(s).

  1. Ultimate dynamics of the Kirschner-Panetta model: Tumor eradication and related problems

    Science.gov (United States)

    Starkov, Konstantin E.; Krishchenko, Alexander P.

    2017-10-01

    In this paper we consider the ultimate dynamics of the Kirschner-Panetta model which was created for studying the immune response to tumors under special types of immunotherapy. New ultimate upper bounds for compact invariant sets of this model are given, as well as sufficient conditions for the existence of a positively invariant polytope. We establish three types of conditions for the nonexistence of compact invariant sets in the domain of the tumor-cell population. Our main results are two types of conditions for global tumor elimination depending on the ratio between the proliferation rate of the immune cells and their mortality rate. These conditions are described in terms of simple algebraic inequalities imposed on model parameters and treatment parameters. Our theoretical studies of ultimate dynamics are complemented by numerical simulation results.

  2. Ultimate Owner and Firm Performance - Evidence from Romanian Mining and Quarrying Listed Firms

    Directory of Open Access Journals (Sweden)

    Cosmin MIHAI

    2012-08-01

    Full Text Available The main objectives of this paper are to describe the necessary steps to identify the ultimate owner and to investigate the relation between the ultimate ownership and the financial performance of Romanian mining and quarrying listed firms. The study was conducted for the companies listed on Bucharest Stock Exchange, in both regulated and non-regulated segments. The final sample included 17 companies of mining and quarrying. Return on Equity was used for measuring the financial performance of the firms. The ultimate ownership was measured by the percentage of voting rights held by a shareholder. Econometric tools like multiple linear regression analysis were used for analysis. The results of the study suggest that there is a significant negative link between financial performance and divergence between voting rights and cash-flow rights.

  3. The importance of mines for ultimate storage at Deilmann-Haniel Shaft Sinking

    International Nuclear Information System (INIS)

    Greinacher, Jochen; Oellers, Thomas; Ahlbrecht, Thomas

    2011-01-01

    Deilmann-Haniel Shaft Sinking GmbH and its predecessor and associate companies have been involved in projects for underground ultimate storage in Germany, Europe and America for over 45 years. The field of activities previously comprised surveying, planning and sinking of shafts, repair and conversion work, design of underground sealing structures, planning of conveyors and support of the BfS in planning approval procedures. Following discontinuation of activities in the German coal mining industry the use of mines for ultimate storage is an important support for German specialist mining companies. The use of mines for ultimate storage ensures that the existing mining know how in Germany is maintained, because training of the younger generation on the commercial and engineering side of the companies is made possible by the imminent major projects.

  4. Determining the optimum length of a bridge opening with a specified reliability level of water runoff

    Directory of Open Access Journals (Sweden)

    Evdokimov Sergey

    2017-01-01

    Full Text Available Current trends in construction are aimed at providing reliability and safety of engineering facilities. According to the latest government regulations for construction, the scientific approach to engineering research, design, construction and operation of construction projects is a key priority. The reliability of a road depends on a great number of factors and characteristics of their statistical compounds (sequential and parallel. A part of a road with such man-made structures as a bridge or a pipe is considered as a system with a sequential element connection. The overall reliability is the multiplication of the reliability of these elements. The parameters of engineering structures defined by analytical dependences are highly volatile because of the inaccuracy of the defining factors. However each physical parameter is statistically unstable that is evaluated by variable coefficient of their values. It causes the fluctuation in the parameters of engineering structures. Their study may result in the changes in general and particular design rules in order to increase the reliability. The paper gives the grounds for these changes by the example of a bridge. It allows calculating its optimum length with a specified reliability level of water runoff under the bridge.

  5. Defining asthma in genetic studies

    NARCIS (Netherlands)

    Koppelman, GH; Postma, DS; Meijer, G.

    1999-01-01

    Genetic studies have been hampered by the lack of a gold standard to diagnose asthma. The complex nature of asthma makes it more difficult to identify asthma genes. Therefore, approaches to define phenotypes, which have been successful in other genetically complex diseases, may be applied to define

  6. Adaptive Landing Gear: Optimum Control Strategy and Potential for Improvement

    Directory of Open Access Journals (Sweden)

    Grzegorz Mikułowski

    2009-01-01

    Full Text Available An adaptive landing gear is a landing gear (LG capable of active adaptation to particular landing conditions by means of controlled hydraulic force. The objective of the adaptive control is to mitigate the peak force transferred to the aircraft structure during touch-down, and thus to limit the structural fatigue factor. This paper investigates the ultimate limits for improvement due to various strategies of active control. Five strategies are proposed and investigated numerically using a~validated model of a real, passive landing gear as a reference. Potential for improvement is estimated statistically in terms of the mean and median (significant peak strut forces as well as in terms of the extended safe sinking velocity range. Three control strategies are verified experimentally using a laboratory test stand.

  7. On the decrease of ultimate elongation of gum elastomer by irradiation

    International Nuclear Information System (INIS)

    Ito, Masayuki

    1986-01-01

    The reason why the ultimate elongation of gum elastomer decreases by irradiation was studied. The sample used is tetrafluoroethylenepropylene copolymer vulcanized which is a heat resistant elastomer. The sample was irradiated by a electron beam at room temperature. Cross-linking predominate in the operation. (Case 1) Scission predominant condition (Case 2) was given by irradiation of Co-60 γ ray at 100 deg C. Alternative irradiation of γ ray and electron beam under above condition can keep the original cross-linking density by the appropriate choice of each of the doses. (Case 3) The three cases mentioned above involve all of the cases of radiation induced aging of elastomers. Therefor, the following explanation for three cases shows the reason why the ultimate elongation of gum elastomer decreases by irradiation. Case 1. Cross-linking predominant condition. Ultimate elongation is proportional to -0.5 power of the dose. This fact can be explicable by the model of Buche, i.e. the breaking of a short chain causes another to break and that so on throughout the whole sample. Case 2. Chain scission predominant condition. Ultimate elongation increases by irradiation for a certain dose. This fact can understand by the model of Buche. But from a certain dose ultimate elongation does not increase. In the period the structure of the sample turned to be the same structure as the low molecular weight amorphose polymer vulcanized. Case 3. Rate of cross-linking and scission is the same. The average chain length does not chainge in the condition. But the distribution of chain length became wider and wider by irradiation. The increase of short chain result the decrease in ultimate elongation. (author)

  8. A study for the development of a vegetable planter for Optimum stand establishment

    International Nuclear Information System (INIS)

    Zaidi, M.A.; Amjad, N.; Shah, S.U.S

    2013-01-01

    Seed placement and establishment is probably the most crucial phase in the life of a vegetable crop, therefore, the role of the planter or seeder is of vital importance. The objective of this study was to assess the demand of a vegetable planter/seeder and to collect information from farmers, machinery manufacturers and stakeholders to design a new planter for vegetables, initially for pea crop. To achieve the objective of this study, a survey was conducted in three provinces (Punjab, Sindh and Baluchistan) of the country and 34 farmers, 21 officers from the concerned institutions and 14 manufactures were interviewed. Furthermore, three existing planters/drills used for sowing different crops were picked from different sources for evaluating their comparative performance for planting pea. The status of vegetable planting or sowing as a whole was not found encouraging in the country and most vegetables are grown manually that are time consuming and labour intensive practices. Farmers are vigorously demanding a planter or seeder for vegetables. From the evaluation of existing machines, it was concluded that a pneumatic planter for sowing vegetables on beds is the most precise method that drops 10 to 20 seeds per meter length at recommended forward speed with single seed placement per hill. This ensures not only the optimum seed rate, but also eliminates the need for thinning after germination. Using this machine farmers may be able to save two third of the seed quantity for pea crop together with achieving additional benefits of vegetables mechanisation. Therefore, a vegetable planter, initially for pea, should be developed locally to enhance productivity of vegetables, because root establishment of vegetable crops is very critical factor that affects ultimate yield. (author)

  9. Simulation of heat exchanger network (HEN) and planning the optimum cleaning schedule

    International Nuclear Information System (INIS)

    Sanaye, Sepehr; Niroomand, Behzad

    2007-01-01

    Modeling and simulation of heat exchanger networks for estimating the amount of fouling, variations in overall heat transfer coefficient, and variations in outlet temperatures of hot and cold streams has a significant effect on production analysis. In this analysis, parameters such as the exchangers' types and arrangements, their heat transfer surface areas, mass flow rates of hot and cold streams, heat transfer coefficients and variations of fouling with time are required input data. The main goal is to find the variations of the outlet temperatures of the hot and cold streams with time to plan the optimum cleaning schedule of heat exchangers that provides the minimum operational cost or maximum amount of savings. In this paper, the simulation of heat exchanger networks is performed by choosing an asymptotic fouling function. Two main parameters in the asymptotic fouling formation model, i.e. the decay time of fouling formation (τ) and the asymptotic fouling resistance (R f ∼ ) were obtained from empirical data as input parameters to the simulation relations. These data were extracted from the technical history sheets of the Khorasan Petrochemical Plant to guaranty the consistency between our model outputs and the real operating conditions. The output results of the software program developed, including the variations with time of the outlet temperatures of the hot and cold streams, the heat transfer coefficient and the heat transfer rate in the exchangers, are presented for two case studies. Then, an objective function (operational cost) was defined, and the optimal cleaning schedule of the HEN (heat exchanger network) in the Urea and Ammonia units were found by minimizing the objective function using a numerical search method. Based on this minimization procedure, the decision was made whether a heat exchanger should be cleaned or continue to operate. The final result was the most cost effective plan for the HEN cleaning schedule. The corresponding savings by

  10. Optimum ratio of main mechanized operations for direct-flow fertilizers introduction

    Directory of Open Access Journals (Sweden)

    V. P. Uvarov

    2016-01-01

    Full Text Available Use of transport and technological means is carried out according to the direct-flow scheme and includes stage-by-stage performance as the main standard-setting operations (fertilizers transportation, movement and their distribution across a field, and auxiliary (return from a field and loading of fertilizers. The method of comparison of main types of operations at fertilizers application is given. An estimation criterion is a ratio of cargo movements on a road and across a field, proportionality coefficient between movement of freight and a fertilizers distribution area across the field. These indicators depend on transportation distances and doses of fertilizers application, and also on technology factor that is freight moving frequency across the field. The last characteristic is taken as the optimized parameter. An extremum of this indicator was searched due to a classical method. Optimum values of estimated indicators with the accounting of a variation of a ratio of load capacity and operating width of technical means are received. Concrete combinations of transportation distances and doses of fertilizers application are specified. The authors defined conditions of effective use of tractor and perspective automobile transport and technological means. They recommended to use the automeans allowing to change operating width. Realization of the stated methodological approach will make it possible to select an optimum ratio of the mechanized operations at direct-flow fertilizers application, to exclude additional cargo movements across the field, to cut fuel consumption, to increase productivity. Productivity of transport and technological means increases by 2.0; 1.3 and 1.15 times respectively to length of furrow 3; 9 and 27 km at fertilizers application by a dose of 0.06 kg per sq.m.

  11. Evaluation of inbreeding in laying hens by applying optimum genetic contribution and gene flow theory.

    Science.gov (United States)

    König, S; Tsehay, F; Sitzenstock, F; von Borstel, U U; Schmutz, M; Preisinger, R; Simianer, H

    2010-04-01

    Due to consistent increases of inbreeding of on average 0.95% per generation in layer populations, selection tools should consider both genetic gain and genetic relationships in the long term. The optimum genetic contribution theory using official estimated breeding values for egg production was applied for 3 different lines of a layer breeding program to find the optimal allocations of hens and sires. Constraints in different scenarios encompassed restrictions related to additive genetic relationships, the increase of inbreeding, the number of selected sires and hens, and the number of selected offspring per mating. All these constraints enabled higher genetic gain up to 10.9% at the same level of additive genetic relationships or in lower relationships at the same gain when compared with conventional selection schemes ignoring relationships. Increases of inbreeding and genetic gain were associated with the number of selected sires. For the lowest level of the allowed average relationship at 10%, the optimal number of sires was 70 and the estimated breeding value for egg production of the selected group was 127.9. At the highest relationship constraint (16%), the optimal number of sires decreased to 15, and the average genetic value increased to 139.7. Contributions from selected sires and hens were used to develop specific mating plans to minimize inbreeding in the following generation by applying a simulated annealing algorithm. The additional reduction of average additive genetic relationships for matings was up to 44.9%. An innovative deterministic approach to estimate kinship coefficients between and within defined selection groups based on gene flow theory was applied to compare increases of inbreeding from random matings with layer populations undergoing selection. Large differences in rates of inbreeding were found, and they underline the necessity to establish selection tools controlling long-term relationships. Furthermore, it was suggested to use

  12. Simulation of heat exchanger network (HEN) and planning the optimum cleaning schedule

    Energy Technology Data Exchange (ETDEWEB)

    Sanaye, Sepehr [Energy Systems Improvement Laboratory, Mechanical Engineering Department, Iran University of Science and Technology (IUST), Narmak, Tehran 16488 (Iran, Islamic Republic of)]. E-mail: sepehr@iust.ac.ir; Niroomand, Behzad [Energy Systems Improvement Laboratory, Mechanical Engineering Department, Iran University of Science and Technology (IUST), Narmak, Tehran 16488 (Iran, Islamic Republic of)

    2007-05-15

    Modeling and simulation of heat exchanger networks for estimating the amount of fouling, variations in overall heat transfer coefficient, and variations in outlet temperatures of hot and cold streams has a significant effect on production analysis. In this analysis, parameters such as the exchangers' types and arrangements, their heat transfer surface areas, mass flow rates of hot and cold streams, heat transfer coefficients and variations of fouling with time are required input data. The main goal is to find the variations of the outlet temperatures of the hot and cold streams with time to plan the optimum cleaning schedule of heat exchangers that provides the minimum operational cost or maximum amount of savings. In this paper, the simulation of heat exchanger networks is performed by choosing an asymptotic fouling function. Two main parameters in the asymptotic fouling formation model, i.e. the decay time of fouling formation ({tau}) and the asymptotic fouling resistance (R{sub f}{sup {approx}}) were obtained from empirical data as input parameters to the simulation relations. These data were extracted from the technical history sheets of the Khorasan Petrochemical Plant to guaranty the consistency between our model outputs and the real operating conditions. The output results of the software program developed, including the variations with time of the outlet temperatures of the hot and cold streams, the heat transfer coefficient and the heat transfer rate in the exchangers, are presented for two case studies. Then, an objective function (operational cost) was defined, and the optimal cleaning schedule of the HEN (heat exchanger network) in the Urea and Ammonia units were found by minimizing the objective function using a numerical search method. Based on this minimization procedure, the decision was made whether a heat exchanger should be cleaned or continue to operate. The final result was the most cost effective plan for the HEN cleaning schedule. The

  13. Ultimate strength and ductility of steel reinforced concrete beam-columns

    International Nuclear Information System (INIS)

    Shohara, Ryoichi

    1991-01-01

    The ultimate strength and ductility of SRC beam-columns are investigated using the data gathered in Architectural Institute of Japan. Though the simple superposed strength formula in AIJ standard underestimates the strength of SRC beam-column failed in flexure, the generalized superposed strength formula estimates it satisfactory. The strength formula in AIJ standard does not good agreement with test data. The SRC beam-column failed in shear has almost equalductility with that failed in flexure owing to the encased steel. Author presents the formulas which estimate the ultimate deformation angle for SRC beam-columns. (author)

  14. Maintained ship hull girder ultimate strength reliability considering corrosion and fatigue

    DEFF Research Database (Denmark)

    Hu, Yong; Cui, W.; Pedersen, Preben Terndrup

    2004-01-01

    The prupose of this paper is to propose a methodology to assess the time-variant ultimate strength of ship hull girder under the degradations of corrosion and fatigue. The effects of fatigue cracks on the tensile and compressive residual ultimate strength of stiffened panels and unstiffened plates......, webs and flanges, respectively. The effects of inspections and repair are taken into account. A minimum net thickness rule is used to determine repair policies. A procedure is proposed to determine the maximum allowable corrosion thickness of different parts of the hull cross section. The procedure...

  15. Behaviour of concrete nuclear containment structures upto ultimate failure with special reference to MAPP-1 containment

    International Nuclear Information System (INIS)

    Appa Rao, T.V.S.R.

    1975-01-01

    Theoretical and experimental methods for investigating the behaviour of concrete secondary containment structures subjected to loads upto their ultimate failure have been discussed in the paper. Need for inelastic nonlinear analysis of containments has been emphasized. Different contitutive models of concrete that can be employed in the nonlinear analysis of concrete structures were briefly reviewed. Based on the experimental results obtained in a 1:12 scale model test conducted at the Structural Engineering Research (Regional) Centre, Madras, behaviour of the MAPP-1 containment to internal pressure loading upto its ultimate failure has been discussed. (author)

  16. Decision basis for a Danish ultimate storage for low and intermediate radioactive wastes

    International Nuclear Information System (INIS)

    2008-11-01

    In 2003 the Danish Parliament consented to let the government start the preparation of a basis for decision on a Danish ultimate storage for low and intermediate radioactive wastes. The present report was prepared by a working group and it presents the final proposal for such a decision basis. The report describes the fundamental safety and environmental principles for establishing an ultimate storage, including determining the principles for site selection, storage construction, and safety analysis. In an appendix, the amount, types, and activity level of the Danish radioactive wastes are presented. (ln)

  17. Conception of electron beam-driven subcritical molten salt ultimate safety reactor

    Energy Technology Data Exchange (ETDEWEB)

    Abalin, S.S.; Alekseev, P.N.; Ignat`ev, V.V. [Kurchatov Institute, Moscow (Russian Federation)] [and others

    1995-10-01

    This paper is a preliminary sketch of a conception to develop the {open_quotes}ultimate safety reactor{close_quotes} using modern reactor and accelerator technologies. This approach would not require a long-range R&D program. The ultimate safety reactor could produce heat and electric energy, expand the production of fuel, or be used for the transmutation of long-lived wastes. The use of the combined double molten salt reactor system allows adequate neutron multiplication to permit using an electron accelerator for the initial neutron flux. The general parameters of such a system are discussed in this paper.

  18. Determination of Optimum Cross-section for Oran Highway Revetment

    Science.gov (United States)

    Velioglu, Deniz; Sogut, Erdinc; Guler, Isikhan

    2017-04-01

    Revetments are shore parallel, sloping coastal structures which are built to provide protection from the negative effects of the sea. The revetment mentioned in this study is located in the City of Oran, Algeria and is currently under construction. This study investigates the determination of the optimum revetment cross section for Oran highway, considering both the hydraulic stability of the revetment and economy. The existence of cliffs in the region and the settlement of the City of Oran created a necessity to re-align Oran highway; therefore, it was shifted towards the Gulf of Oran. Approximately 1 km of the highway is to be constructed on the Mediterranean Sea due to the new alignment. In order to protect the sea side of the road from the adverse effects of the sea, a revetment was designed. The proposed cross section had an armour layer composed of 23 tons of antifer units and regular placement of armour units was recommended. In order to check the hydraulic stability of the proposed section, physical model tests were performed in the laboratory of LEM (Laboratoire d'Etudes Maritimes) in Algeria, using the pre-determined design wave conditions. The physical model tests revealed that the trunk of the revetment was totaly damaged. Accordingly, the proposed section was found insufficient and certain modifications were required. The first modification was made in the arrangement of armour units, changing them from regular to irregular. After testing the new cross section, it was observed that the revetment was vulnerable to breaking wave attack due to the toe geometry and thus the toe of the revetment had to be re-shaped. Therefore, the second option was to reduce the toe elevation. It was observed that even though the revetment trunk was safe, the damage in the toe was not in acceptable limits. The new cross section was found insufficient and as the final option, the weight of the antifer units used in the armour layer was increased, the toe length of the

  19. Optimum operation of restoration techniques for eutrophic water bodies

    Science.gov (United States)

    Hagen, N. M.; Kleeberg, H.-B.

    1994-05-01

    Operating rules have been applied in water resources management for a long time in order to control and supply a required quantity (volume) of water. The operating rules have to guarantee the optimum management of the reservoir(s). The quality of the stored water has been satisfactory for the desired utilization up to the sixties. Due to the deterioration of reservoir water quality through human impacts, however, increased attention had to be paid since. Eutrophication of stagnant waters is still an unsolved problem. Through means of various restoration techniques, i.e., dilution/flushing or hypolimnetic withdrawal, the quality of the stored water can be improved. Continuous operation or appropriate time or depth variant operating rules are required to achieve this goal. The paper presents such rules for long-term operation. They have been established for the first time and can he represented in two or three-dimensional graphs depending on the number of included components (e.g., actual water storage and quality). The ‘quality operating rules’ take into account the dynamics of the processes in aquatic ecosystems. Simplifications with regard to application and acceptance (e.g., clarity) are developed and tested. The general validity and efficiency of the operating rules have been proved in a case study (a multi-purpose reservoir) and a fictitious lake.

  20. Optimum Resource Allocation and Eliminating Waste Inside Food Industry

    Directory of Open Access Journals (Sweden)

    Chandru Nagarajan Sathiyabama

    2013-06-01

    Full Text Available This article seeks to allocate optimum resources for wrapping section and suggesting a suitable method that need to be in place for successful elimination of waste inside the food industry wrapping section. It also includes identifying the main reasons for various types of wastages inside wrapping section and cost of all the wastages. The paper is based on the observation and research using the approach of lean tools and techniques. The methodology used for evaluating data is value stream mapping and some statistical SPSS tools for analysis. Data’s are real and are gathered from three different production shifts inside a food industry wrapping section. The main reasons for wastages inside the wrapping section are highlighted. Finally, the paper was concluded by estimating total cost of wastages and recommended suitable way to save the wastage costs. The need of change of jaws inside the wrapping machines, regular maintenance of all machines throughout the industry and training the personnel are recommended. The possible methods along with its benefits to reduce waste, operators, improve productivity and business growth was also highlighted.

  1. Determination of Optimum Compression Ratio: A Tribological Aspect

    Directory of Open Access Journals (Sweden)

    L. Yüksek

    2013-12-01

    Full Text Available Internal combustion engines are the primary energy conversion machines both in industry and transportation. Modern technologies are being implemented to engines to fulfill today's low fuel consumption demand. Friction energy consumed by the rubbing parts of the engines are becoming an important parameter for higher fuel efficiency. Rate of friction loss is primarily affected by sliding speed and the load acting upon rubbing surfaces. Compression ratio is the main parameter that increases the peak cylinder pressure and hence normal load on components. Aim of this study is to investigate the effect of compression ratio on total friction loss of a diesel engine. A variable compression ratio diesel engine was operated at four different compression ratios which were "12.96", "15:59", "18:03", "20:17". Brake power and speed was kept constant at predefined value while measuring the in- cylinder pressure. Friction mean effective pressure ( FMEP data were obtained from the in cylinder pressure curves for each compression ratio. Ratio of friction power to indicated power of the engine was increased from 22.83% to 37.06% with varying compression ratio from 12.96 to 20:17. Considering the thermal efficiency , FMEP and maximum in- cylinder pressure optimum compression ratio interval of the test engine was determined as 18.8 ÷ 19.6.

  2. Optimum Image Formation for Spaceborne Microwave Radiometer Products.

    Science.gov (United States)

    Long, David G; Brodzik, Mary J

    2016-05-01

    This paper considers some of the issues of radiometer brightness image formation and reconstruction for use in the NASA-sponsored Calibrated Passive Microwave Daily Equal-Area Scalable Earth Grid 2.0 Brightness Temperature Earth System Data Record project, which generates a multisensor multidecadal time series of high-resolution radiometer products designed to support climate studies. Two primary reconstruction algorithms are considered: the Backus-Gilbert approach and the radiometer form of the scatterometer image reconstruction (SIR) algorithm. These are compared with the conventional drop-in-the-bucket (DIB) gridded image formation approach. Tradeoff study results for the various algorithm options are presented to select optimum values for the grid resolution, the number of SIR iterations, and the BG gamma parameter. We find that although both approaches are effective in improving the spatial resolution of the surface brightness temperature estimates compared to DIB, SIR requires significantly less computation. The sensitivity of the reconstruction to the accuracy of the measurement spatial response function (MRF) is explored. The partial reconstruction of the methods can tolerate errors in the description of the sensor measurement response function, which simplifies the processing of historic sensor data for which the MRF is not known as well as modern sensors. Simulation tradeoff results are confirmed using actual data.

  3. Optimum Drafting Conditions Of Polyester And Viscose Blend Yarns

    Directory of Open Access Journals (Sweden)

    Hatamvand Mohammad

    2017-09-01

    Full Text Available In this study, we used an experimental design to investigate the influence of the total draft, break draft, distance between the aprons (Clips and production roller pressure on yarn quality in order to obtain optimum drafting conditions for polyester and viscose (PES/CV blend yarns in ring spinning frame. We used PES fibers (1.4 dtex × 38 mm long and CV fibers (1.6 dtex × 38 mm long to spin a 20 Tex blend yarn of PES (70%/CV (30% blend ratio. When the break draft, adjustment of distance between of aprons and roller pressure is not reasonable, controlling and leading of the fibers is not sufficient for proper orientation of the fibers in the yarn structure to produce a high quality yarn. Experimental results and statistical analysis show that the best yarn quality will be obtained under drafting conditions total draft of 38, 1.2 break draft, 2.8 mm distance between of aprons and maximum pressure of the production top roller (18daN.

  4. Optimum sizing of wind-battery systems incorporating resource uncertainty

    International Nuclear Information System (INIS)

    Roy, Anindita; Kedare, Shireesh B.; Bandyopadhyay, Santanu

    2010-01-01

    The inherent uncertainty of the wind is a major impediment for successful implementation of wind based power generation technology. A methodology has been proposed in this paper to incorporate wind speed uncertainty in sizing wind-battery system for isolated applications. The uncertainty associated with the wind speed is incorporated using chance constraint programming approach. For a pre-specified reliability requirement, a deterministic equivalent energy balance equation may be derived from the chance constraint that allows time series simulation of the entire system. This results in a generation of the entire set of feasible design options, satisfying different system level constraints, on a battery capacity vs. generator rating diagram, also known as the design space. The proposed methodology highlights the trade-offs between the wind turbine rating, rotor diameter and the battery size for a given reliability of power supply. The optimum configuration is chosen on the basis of the minimum cost of energy (US$/kWh). It is shown with the help of illustrative examples that the proposed methodology is generic and flexible to incorporate alternate sub-component models. (author)

  5. Analysis of optimum density of forest roads in rural properties

    Directory of Open Access Journals (Sweden)

    Flávio Cipriano de Assis do Carmo

    2013-09-01

    Full Text Available This study analyzed the density of roads in rural properties in the south of the Espírito Santo and compared it with the calculation of the optimal density in forestry companies in steep areas. The work was carried out in six small rural properties based on the costs of roads of forest use, wood extraction and the costs of loss of productive area. The technical analysis included time and movement study and productivity. The economic analysis included operational costs, production costs and returns for different scenarios of productivity (180m.ha-1, 220m.ha-1and 250 m.ha-1. According to the results, all the properties have densities of road well above the optimum, which reflects the lack of criteria in the planning of the forest stands, resulting in a inadequate use of plantation area. Property 1 had the highest density of roads (373.92 m.ha-1 and the property 5 presented the lowest density (111.56 m.ha-1.

  6. An Optimum Solution for Electric-Power Theft

    International Nuclear Information System (INIS)

    Memon, A.H.; Memon, F.

    2013-01-01

    Electric power theft is a problem that continues to plague power sector across the whole country. Every year, the electricity companies face the line losses at an average 20-30% and according to power ministry estimation WAPDA companies lose more than Rs. 125 billion. Significantly, it is enough to destroy the entire power sector of country. According to sources 20% losses means the masses would have to pay extra 20% in terms of electricity tariffs. In other words, the innocent consumers pay the bills of those who steal electricity. For all that, no any permanent solution for this major issue has ever been proposed. We propose an applicable and optimum solution for this impassable problem. In our research, we propose an Electric power theft solution based on three stages; Transmission stage, Distribution stage, and User stage. Without synchronization among all, the complete solution can not be achieved. The proposed solution is simulated on NI (National Instruments) Circuit Design Suite Multisim v.10.0. Our research work is an implicit and a workable approach towards the Electric power theft, as for conditions in Pakistan, which is bearing the brunt of power crises already. (author)

  7. Optimum Water Chemistry in radiation field buildup control

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Chien, C. [Vallecitos Nuclear Center, Pleasanton, CA (United States)

    1995-03-01

    Nuclear utilities continue to face the challenGE of reducing exposure of plant maintenance personnel. GE Nuclear Energy has developed the concept of Optimum Water Chemistry (OWC) to reduce the radiation field buildup and minimize the radioactive waste production. It is believed that reduction of radioactive sources and improvement of the water chemistry quality should significantly reduce both the radiation exposure and radwaste production. The most important source of radioactivity is cobalt and replacement of cobalt containing alloy in the core region as well as in the entire primary system is considered the first priority to achieve the goal of low exposure and minimized waste production. A plant specific computerized cobalt transport model has been developed to evaluate various options in a BWR system under specific conditions. Reduction of iron input and maintaining low ionic impurities in the coolant have been identified as two major tasks for operators. Addition of depleted zinc is a proven technique to reduce Co-60 in reactor water and on out-of-core piping surfaces. The effect of HWC on Co-60 transport in the primary system will also be discussed.

  8. Optimum hypersonic airfoil with power law shock waves

    International Nuclear Information System (INIS)

    Wagner, B.A.

    1990-01-01

    In the present paper the flow field over a class of two-dimensional lifting surfaces is examined from the viewpoint of inviscid, hypersonic small-disturbance theory (HSDT). It is well known that a flow field in which the shock shape S(x) is similar to the body shape F(x) is only possible for F(x) = x k and the freestream Mach number M ∞ = ∞. This self-similar flow has been studied for several decades as it represents one of the few existing exact solutions of the equations of HSDT. Detailed discussions are found for example in papers by Cole, Mirels, Chernyi and Gersten and Nicolai but they are limited to convex body shapes, that is, k ≤ 1. The only study of concave body shapes was attempted by Sullivan where only special cases were considered. The method used here shows that similarity also exists for concave shapes and a complete solution of the flow field for any k > 2/3 is given. The effect of varying k on C L 3/2 /C D is then determined and an optimum shape is found. Furthermore, a wider class of lifting surfaces is constructed using the streamlines of the basic flow field and analysed with respect to the effect on C L 3/2 /C D . 9 refs., 3 figs

  9. Prediction of Local Ultimate Strain and Toughness of Trabecular Bone Tissue by Raman Material Composition Analysis

    Directory of Open Access Journals (Sweden)

    Roberto Carretta

    2015-01-01

    Full Text Available Clinical studies indicate that bone mineral density correlates with fracture risk at the population level but does not correlate with individual fracture risk well. Current research aims to better understand the failure mechanism of bone and to identify key determinants of bone quality, thus improving fracture risk prediction. To get a better understanding of bone strength, it is important to analyze tissue-level properties not influenced by macro- or microarchitectural factors. The aim of this pilot study was to identify whether and to what extent material properties are correlated with mechanical properties at the tissue level. The influence of macro- or microarchitectural factors was excluded by testing individual trabeculae. Previously reported data of mechanical parameters measured in single trabeculae under tension and bending and its compositional properties measured by Raman spectroscopy was evaluated. Linear and multivariate regressions show that bone matrix quality but not quantity was significantly and independently correlated with the tissue-level ultimate strain and postyield work (r=0.65–0.94. Principal component analysis extracted three independent components explaining 86% of the total variance, representing elastic, yield, and ultimate components according to the included mechanical parameters. Some matrix parameters were both included in the ultimate component, indicating that the variation in ultimate strain and postyield work could be largely explained by Raman-derived compositional parameters.

  10. Molar mass of poly(ethylene terephthalate) (PET) during ultimate uniaxial drawing

    NARCIS (Netherlands)

    Göschel, U.; Cools, P.J.C.H.

    2000-01-01

    The changes of the average molar mass Mw, Mn, Mz, and molar mass distributions during multistep uniaxial drawing of poly(ethylene terephthalate) (PET) to achieve ultimate mechanical properties have been studied in detail by means of size exclusion chromatography (SEC) with triple detection:

  11. Molar-Mass of Poly(Ethylene-Terephthalate) (PET) During Ultimate Uniaxial Drawing

    NARCIS (Netherlands)

    Göschel, A.G.P.U.; Cools, P.J.C.H.

    2000-01-01

    The changes of the average molar mass Mw, Mn, Mz, and molar mass distributions during multistep uniaxial drawing of poly(ethylene terephthalate) (PET) to achieve ultimate mechanical properties have been studied in detail by means of size exclusion chromatography (SEC) with triple detection:

  12. Prisoner Fasting as Symbolic Speech: The Ultimate Speech-Action Test.

    Science.gov (United States)

    Sneed, Don; Stonecipher, Harry W.

    The ultimate test of the speech-action dichotomy, as it relates to symbolic speech to be considered by the courts, may be the fasting of prison inmates who use hunger strikes to protest the conditions of their confinement or to make political statements. While hunger strikes have been utilized by prisoners for years as a means of protest, it was…

  13. Reliability analysis of production ships with emphasis on load combination and ultimate strength

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Xiaozhi

    1995-05-01

    This thesis deals with ultimate strength and reliability analysis of offshore production ships, accounting for stochastic load combinations, using a typical North Sea production ship for reference. A review of methods for structural reliability analysis is presented. Probabilistic methods are established for the still water and vertical wave bending moments. Linear stress analysis of a midships transverse frame is carried out, four different finite element models are assessed. Upon verification of the general finite element code ABAQUS with a typical ship transverse girder example, for which test results are available, ultimate strength analysis of the reference transverse frame is made to obtain the ultimate load factors associated with the specified pressure loads in Det norske Veritas Classification rules for ships and rules for production vessels. Reliability analysis is performed to develop appropriate design criteria for the transverse structure. It is found that the transverse frame failure mode does not seem to contribute to the system collapse. Ultimate strength analysis of the longitudinally stiffened panels is performed, accounting for the combined biaxial and lateral loading. Reliability based design of the longitudinally stiffened bottom and deck panels is accomplished regarding the collapse mode under combined biaxial and lateral loads. 107 refs., 76 refs., 37 tabs.

  14. Study of ultimate heat sink to Angra-1,2 and 3 Nuclear Power Plants

    International Nuclear Information System (INIS)

    Moreira, R.M.; Pinto, A.M.F.

    1985-03-01

    This report presents the premises, results and conclusion of study done to ultimate heat sink of Angra 1,2 and 3 units, with base in postulated accidents that generate transient heat discharges to environment. It's explicitily presumed the eventuality of discharging heat water recirculation. (C.M.) [pt

  15. Method for ultimate disposition of borate containing radioactive wastes by vitrification

    International Nuclear Information System (INIS)

    Bege, D.; Faust, H.J.; Puthawala, A.; Stunkel, H.

    1984-01-01

    Method for the ultimate disposition of radioactive wastes by vitrification, in which weak to medium radioactive waste concentrates from borate-containing radioactive liquids are mixed with added glass-forming materials, maximally in a ratio of 1:3, and the mixture heated to obtain a glass-forming melt

  16. 26 CFR 48.6427-10 - Kerosene; claims by registered ultimate vendors (blocked pumps).

    Science.gov (United States)

    2010-04-01

    ... (blocked pumps). 48.6427-10 Section 48.6427-10 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE...; claims by registered ultimate vendors (blocked pumps). (a) Overview. This section provides rules under... allowed by section 6427(l)(5)(B)(i). These claims relate to kerosene sold from a blocked pump. Claims...

  17. Discussion of the Method to Determine the Ultimate Bearing Capacity of Soil Foundation

    Science.gov (United States)

    Du, Peng; Liu, Xiaoling; Zhang, Yangfu

    2017-12-01

    Combining literature examples, this paper has carried out Contrastive analysis of the theoretical formula method and finite element method about the ultimate bearing capacity of foundation, To verify rationality and superiority of the incremental load method in finite element ABAQUS in solving the bearing capacity of foundation soil. The study can provide certain reference for practical engineering calculation and analysis of foundation bearing capacity.

  18. Too many journals? Towards a theory of repeated rejections and ultimate acceptance

    NARCIS (Netherlands)

    Oosterhaven, Jan

    Under a set of reasonable assumptions, it is shown that all manuscripts submitted to any journal will ultimately be published, either by the first journal or by one of the following journals to which a manuscript is resubmitted. This suggests that low quality manuscripts may also be published, which

  19. A comparison of international criteria for the ultimate storage of radioactive wastes

    International Nuclear Information System (INIS)

    Mielke, H.

    1985-01-01

    In countries other than the Federal Republic of Germany and internationally there are no comprehensive codes referring to criteria and safety requirements except those of the IAEA and USA. In other countries there exist safety goals for the ultimate storage or for purely geological criteria. The degree of detailing regulations differs widely abroad and internationally. Safety goals abroad and internationally as well as measures for their realisation in the ultimate storage of radioactive wastes in deep geological formations are in line with the German safety goals. The IAEA refers to general aspects of geological, waste technology and ultimate storage technology criteria. In the USA, ultimate storage technology criteria have been quantified in part. The quantitative geological criteria existing in Great Britain and in the Netherlands are only relevant in as much as safety analyses must be performed for a specific site to provide evidence for the safety of this site. The comparison shows that most requirements pronounced abroad are also made for the Federal Republic of Germany. Some requirements are more specified in the Federal Republic of Germany, some are more detailed abroad. (orig./HP) [de

  20. proximate and ultimate analysis of fuel pellets from oil palm residues

    African Journals Online (AJOL)

    HOD

    Keywords: Oil Palm Residues, Fuel Pellets, Proximate Analysis, Ultimate Analysis. 1. INTRODUCTION ... Pelletizing of this biomass resources into pellets is a way of ensuring a ... demand for pellets [3], and alternative feed-stocks such as palm kernel ... agro-residues, selection of the best pellets has to be made based on ...

  1. 7 CFR 4280.29 - Supplemental financing required for the Ultimate Recipient Project.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Supplemental financing required for the Ultimate Recipient Project. 4280.29 Section 4280.29 Agriculture Regulations of the Department of Agriculture... AND GRANTS Rural Economic Development Loan and Grant Programs § 4280.29 Supplemental financing...

  2. Theoretical approaches to elections defining

    OpenAIRE

    Natalya V. Lebedeva

    2011-01-01

    Theoretical approaches to elections defining develop the nature, essence and content of elections, help to determine their place and a role as one of the major national law institutions in democratic system.

  3. Theoretical approaches to elections defining

    Directory of Open Access Journals (Sweden)

    Natalya V. Lebedeva

    2011-01-01

    Full Text Available Theoretical approaches to elections defining develop the nature, essence and content of elections, help to determine their place and a role as one of the major national law institutions in democratic system.

  4. Defining the landscape of adaptive genetic diversity.

    Science.gov (United States)

    Eckert, Andrew J; Dyer, Rodney J

    2012-06-01

    Whether they are used to describe fitness, genome architecture or the spatial distribution of environmental variables, the concept of a landscape has figured prominently in our collective reasoning. The tradition of landscapes in evolutionary biology is one of fitness mapped onto axes defined by phenotypes or molecular sequence states. The characteristics of these landscapes depend on natural selection, which is structured across both genomic and environmental landscapes, and thus, the bridge among differing uses of the landscape concept (i.e. metaphorically or literally) is that of an adaptive phenotype and its distribution across geographical landscapes in relation to selective pressures. One of the ultimate goals of evolutionary biology should thus be to construct fitness landscapes in geographical space. Natural plant populations are ideal systems with which to explore the feasibility of attaining this goal, because much is known about the quantitative genetic architecture of complex traits for many different plant species. What is less known are the molecular components of this architecture. In this issue of Molecular Ecology, Parchman et al. (2012) pioneer one of the first truly genome-wide association studies in a tree that moves us closer to this form of mechanistic understanding for an adaptive phenotype in natural populations of lodgepole pine (Pinus contorta Dougl. ex Loud.). © 2012 Blackwell Publishing Ltd.

  5. Defining Modules, Modularity and Modularization

    DEFF Research Database (Denmark)

    Miller, Thomas Dedenroth; Pedersen, Per Erik Elgård

    The paper describes the evolution of the concept of modularity in a historical perspective. The main reasons for modularity are: create variety, utilize similarities, and reduce complexity. The paper defines the terms: Module, modularity, and modularization.......The paper describes the evolution of the concept of modularity in a historical perspective. The main reasons for modularity are: create variety, utilize similarities, and reduce complexity. The paper defines the terms: Module, modularity, and modularization....

  6. Choice of Breakwater Type and Optimum Safety Levels

    DEFF Research Database (Denmark)

    Burcharth, Hans F.

    2009-01-01

    Breakwaters belong generally to the more expensive part of port and coastal protection structures. The fact that the main function of breakwaters is to provide shelter for wave action defines automatically the two main problems related to breakwater engineering, namely construction in often very ...

  7. Towards implementation of optimum nutrition and better clinical nutrition support

    NARCIS (Netherlands)

    Jonkers, C. F.; Prins, F.; van Kempen, A.; Tepaske, R.; Sauerwein, H. P.

    2001-01-01

    Clinical Nutrition Support--defined as nutrition for hospitalized patients suffering from metabolic stress--plays a limited role in the therapeutic routine of the physician. This is not surprising as most research in the field of clinical nutrition is disappointing with regard to the objective

  8. Optimum swimming pathways of fish spawning migrations in rivers

    Science.gov (United States)

    McElroy, Brandon; DeLonay, Aaron; Jacobson, Robert

    2012-01-01

    Fishes that swim upstream in rivers to spawn must navigate complex fluvial velocity fields to arrive at their ultimate locations. One hypothesis with substantial implications is that fish traverse pathways that minimize their energy expenditure during migration. Here we present the methodological and theoretical developments necessary to test this and similar hypotheses. First, a cost function is derived for upstream migration that relates work done by a fish to swimming drag. The energetic cost scales with the cube of a fish's relative velocity integrated along its path. By normalizing to the energy requirements of holding a position in the slowest waters at the path's origin, a cost function is derived that depends only on the physical environment and not on specifics of individual fish. Then, as an example, we demonstrate the analysis of a migration pathway of a telemetrically tracked pallid sturgeon (Scaphirhynchus albus) in the Missouri River (USA). The actual pathway cost is lower than 105 random paths through the surveyed reach and is consistent with the optimization hypothesis. The implication—subject to more extensive validation—is that reproductive success in managed rivers could be increased through manipulation of reservoir releases or channel morphology to increase abundance of lower-cost migration pathways.

  9. Optimum Design Of Grid Connected Photovoltaic System Using Concentrators

    Directory of Open Access Journals (Sweden)

    Eng. Mohammed Fawzy

    2015-08-01

    Full Text Available Abstract Due to the increasing demand of electrical energy in Egypt and also in many neighboring countries around the world the main problem facing electrical energy production using classical methods such steam power stations is the depletion of fossil fuels. The gap between the electrical energy demand and the continuous increase on the fossil fuel cost make the problem of electricity generation more sophisticated. With the continuous decrease of the photovoltaic PV technologies cost it doesnt make sense neglecting the importance of electricity production using solar photovoltaic PV especially that the annual average daily energy received is about 6 kamp12310whmamp123112day in Cairo Egypt 30N.In this work a detailed simulation model including photovoltaic PV module characteristics and climatic conditions of Cairo Egypt is developed. The model compares fixed PV systems electrical energy output with photovoltaic PV system using concentrators and double axis tracker systems. The comparison includes the energy generated area required as well as the cost per kwh generated. The optimality criterion is the cost per kwh generated. The system that gives the minimum cost per kwh is the optimum system. To verify the developed model the simulation results of fixed PV modules and CPV using tracking system obtained by the model are compared with practical measurements of 40KW peak station erected in Cairo Egypt 30N.Very good agreement between measured values and results obtained from detailed simulation model. For fixed PV system the detailed economic analysis showed that it gives minimum cost perkwh generated Comparisons among these systems are presented. For Cairo results showed that a cost of about 6 to 9 US centskwh is attainable.

  10. Optimum coagulant forecasting by modeling jar test experiments using ANNs

    Science.gov (United States)

    Haghiri, Sadaf; Daghighi, Amin; Moharramzadeh, Sina

    2018-01-01

    Currently, the proper utilization of water treatment plants and optimizing their use is of particular importance. Coagulation and flocculation in water treatment are the common ways through which the use of coagulants leads to instability of particles and the formation of larger and heavier particles, resulting in improvement of sedimentation and filtration processes. Determination of the optimum dose of such a coagulant is of particular significance. A high dose, in addition to adding costs, can cause the sediment to remain in the filtrate, a dangerous condition according to the standards, while a sub-adequate dose of coagulants can result in the reducing the required quality and acceptable performance of the coagulation process. Although jar tests are used for testing coagulants, such experiments face many constraints with respect to evaluating the results produced by sudden changes in input water because of their significant costs, long time requirements, and complex relationships among the many factors (turbidity, temperature, pH, alkalinity, etc.) that can influence the efficiency of coagulant and test results. Modeling can be used to overcome these limitations; in this research study, an artificial neural network (ANN) multi-layer perceptron (MLP) with one hidden layer has been used for modeling the jar test to determine the dosage level of used coagulant in water treatment processes. The data contained in this research have been obtained from the drinking water treatment plant located in Ardabil province in Iran. To evaluate the performance of the model, the mean squared error (MSE) and correlation coefficient (R2) parameters have been used. The obtained values are within an acceptable range that demonstrates the high accuracy of the models with respect to the estimation of water-quality characteristics and the optimal dosages of coagulants; so using these models will allow operators to not only reduce costs and time taken to perform experimental jar tests

  11. Modeling Budget Optimum Allocation of Khorasan Razavi Province Agriculture Sector

    Directory of Open Access Journals (Sweden)

    Seyed Mohammad Fahimifard

    2016-09-01

    Full Text Available Introduction: Stock shortage is one of the development impasses in developing countries and trough it the agriculture sector has faced with the most limitation. The share of Iran’s agricultural sector from total investments after the Islamic revolution (1979 has been just 5.5 percent. This fact causes low efficiency in Iran’s agriculture sector. For instance per each 1 cubic meter of water in Iran’s agriculture sector, less that 1 kilogram dry food produced and each Iranian farmer achieves less annual income and has less mechanization in comparison with similar countries in Iran’s 1404 perspective document. Therefore, it is clear that increasing investment in agriculture sector, optimize the budget allocation for this sector is mandatory however has not been adequately and scientifically revised until now. Thus, in this research optimum budget allocation of Iran- Khorasan Razavi province agriculture sector was modeled. Materials and Methods: In order to model the optimum budget allocation of Khorasan Razavi province’s agriculture sector at first optimum budget allocation between agriculture programs was modeled with compounding three indexes: 1. Analyzing the priorities of Khorasan Razavi province’s agriculture sector experts with the application of Analytical Hierarchy Process (AHP, 2. The average share of agriculture sector programs from 4th country’s development program for Khorasan Razavi province’s agriculture sector, and 3.The average share of agriculture sector programs from 5th country’s development program for Khorasan Razavi province’s agriculture sector. Then, using Delphi technique potential indexes of each program was determined. After that, determined potential indexes were weighted using Analytical Hierarchy Process (AHP and finally, using numerical taxonomy model to optimize allocation of the program’s budget between cities based on two scenarios. Required data, also was gathered from the budget and planning

  12. Defining Plagiarism: A Literature Review

    Directory of Open Access Journals (Sweden)

    Akbar Akbar

    2018-02-01

    Full Text Available Plagiarism has repeatedly occurred in Indonesia, resulting in focusing on such academic misbehavior as a “central issue” in Indonesian higher education. One of the issues of addressing plagiarism in higher education is that there is a confusion of defining plagiarism. It seems that Indonesian academics had different perception when defining plagiarism. This article aims at exploring the issue of plagiarism by helping define plagiarism to address confusion among Indonesian academics. This article applies literature review by firs finding relevant articles after identifying databases for literature searching. After the collection of required articles for review, the articles were synthesized before presenting the findings. This study has explored the definition of plagiarism in the context of higher education. This research found that plagiarism is defined in the relation of criminal acts. The huge numbers of discursive features used position plagiaristic acts as an illegal deed. This study also found that cultural backgrounds and exposure to plagiarism were influential in defining plagiarism.

  13. Evaluation of mathematical methods for predicting optimum dose of gamma radiation in sugarcane (Saccharum sp.)

    International Nuclear Information System (INIS)

    Wu, K.K.; Siddiqui, S.H.; Heinz, D.J.; Ladd, S.L.

    1978-01-01

    Two mathematical methods - the reversed logarithmic method and the regression method - were used to compare the predicted and the observed optimum gamma radiation dose (OD 50 ) in vegetative propagules of sugarcane. The reversed logarithmic method, usually used in sexually propagated crops, showed the largest difference between the predicted and observed optimum dose. The regression method resulted in a better prediction of the observed values and is suggested as a better method for the prediction of optimum dose for vegetatively propagated crops. (author)

  14. Optimum supervision intervals and order of supervision in nuclear reactor protective systems

    International Nuclear Information System (INIS)

    Kontoleon, J.M.

    1978-01-01

    The optimum inspection strategy of an m-out-of-n:G nuclear reactor protective system with nonidentical units is analyzed. A 2-out-of-4:G system is used to formulate a multi-variable optimization problem to determine (a) the optimum order of supervision of the units and (b) the optimum supervision intervals between units. The case of systems with identical units is a special case of the above. Numerical results are derived using a computer algorithm

  15. Modular Software-Defined Radio

    Directory of Open Access Journals (Sweden)

    Rhiemeier Arnd-Ragnar

    2005-01-01

    Full Text Available In view of the technical and commercial boundary conditions for software-defined radio (SDR, it is suggestive to reconsider the concept anew from an unconventional point of view. The organizational principles of signal processing (rather than the signal processing algorithms themselves are the main focus of this work on modular software-defined radio. Modularity and flexibility are just two key characteristics of the SDR environment which extend smoothly into the modeling of hardware and software. In particular, the proposed model of signal processing software includes irregular, connected, directed, acyclic graphs with random node weights and random edges. Several approaches for mapping such software to a given hardware are discussed. Taking into account previous findings as well as new results from system simulations presented here, the paper finally concludes with the utility of pipelining as a general design guideline for modular software-defined radio.

  16. Defining and Selecting Independent Directors

    Directory of Open Access Journals (Sweden)

    Eric Pichet

    2017-10-01

    Full Text Available Drawing from the Enlightened Shareholder Theory that the author first developed in 2011, this theoretical paper with practical and normative ambitions achieves a better definition of independent director, while improving the understanding of the roles he fulfils on boards of directors. The first part defines constructs like firms, Governance system and Corporate governance, offering a clear distinction between the latter two concepts before explaining the four main missions of a board. The second part defines the ideal independent director by outlining the objective qualities that are necessary and adding those subjective aspects that have turned this into a veritable profession. The third part defines the ideal process for selecting independent directors, based on nominating committees that should themselves be independent. It also includes ways of assessing directors who are currently in function, as well as modalities for renewing their mandates. The paper’s conclusion presents the Paradox of the Independent Director.

  17. Defining and Classifying Interest Groups

    DEFF Research Database (Denmark)

    Baroni, Laura; Carroll, Brendan; Chalmers, Adam

    2014-01-01

    The interest group concept is defined in many different ways in the existing literature and a range of different classification schemes are employed. This complicates comparisons between different studies and their findings. One of the important tasks faced by interest group scholars engaged...... in large-N studies is therefore to define the concept of an interest group and to determine which classification scheme to use for different group types. After reviewing the existing literature, this article sets out to compare different approaches to defining and classifying interest groups with a sample...... in the organizational attributes of specific interest group types. As expected, our comparison of coding schemes reveals a closer link between group attributes and group type in narrower classification schemes based on group organizational characteristics than those based on a behavioral definition of lobbying....

  18. ON DEFINING S-SPACES

    Directory of Open Access Journals (Sweden)

    Francesco Strati

    2013-05-01

    Full Text Available The present work is intended to be an introduction to the Superposition Theory of David Carfì. In particular I shall depict the meaning of his brand new theory, on the one hand in an informal fashion and on the other hand by giving a formal approach of the algebraic structure of the theory: the S-linear algebra. This kind of structure underpins the notion of S-spaces (or Carfì-spaces by defining both its properties and its nature. Thus I shall define the S-triple as the fundamental principle upon which the S-linear algebra is built up.

  19. Ultimate uniaxial compressive strength of stiffened panel with opening under lateral pressure

    Directory of Open Access Journals (Sweden)

    Chang-Li Yu

    2015-03-01

    Full Text Available This paper concentrated on the ultimate uniaxial compressive strength of stiffened panel with opening under lateral load and also studied the design-oriented formulae. For this purpose, three series of well executed experiments on longitudinal stiffened panel with rectangular opening subjected to the combined load have been selected as test models. The finite element analysis package, ABAQUS, is used for simulation with considering the large elasticplastic deflection behavior of stiffened panels. The feasibility of the numerical procedure is verified by a good agreement of experimental results and numerical results. More cases studies are executed employing nonlinear finite element method to analyze the influence of design variables on the ultimate strength of stiffened panel with opening under combined pressure. Based on data, two design formulae corresponding to different opening types are fitted, and accuracy of them is illustrated to demonstrate that they could be applied to basic design of practical engineering structure.

  20. The Assessment of the Ultimate Hull Girder Strength of RO-RO Ship after Damages

    Science.gov (United States)

    Zubair Muis Alie, Muhammad; Sitepu, Ganding; Izaak Latumahin, Samuel

    2018-03-01

    Many accidents of Ro-Ro ships happen in Indonesia such as collision and grounding. When the collision or grounding takes place on the Ro-Ro ship, the ultimate strength of hull structure after damage becomes decrease. Car and passenger decks are critical location since collision and/or grounding occur. In the present study, the assessment of the ultimate hull girder strength is conducted. The cross section of Ro-Ro ship is taken to be analyzed. The collision and grounding damages are assumed to be palced on the side and bottom area, respectively. The damages are created by removing the element from the side shell and bottom part. Finally, the result obtained is compared with one another.

  1. Accelerator physics and technology limitations to ultimate energy and luminosity in very large hadron colliders

    Energy Technology Data Exchange (ETDEWEB)

    P. Bauer et al.

    2002-12-05

    The following presents a study of the accelerator physics and technology limitations to ultimate energy and luminosity in very large hadron colliders (VLHCs). The main accelerator physics limitations to ultimate energy and luminosity in future energy frontier hadron colliders are synchrotron radiation (SR) power, proton-collision debris power in the interaction regions (IR), number of events-per-crossing, stored energy per beam and beam-stability [1]. Quantitative estimates of these limits were made and translated into scaling laws that could be inscribed into the particle energy versus machine size plane to delimit the boundaries for possible VLHCs. Eventually, accelerator simulations were performed to obtain the maximum achievable luminosities within these boundaries. Although this study aimed at investigating a general VLHC, it was unavoidable to refer in some instances to the recently studied, [2], 200 TeV center-of-mass energy VLHC stage-2 design (VLHC-2). A more thorough rendering of this work can be found in [3].

  2. Ultimate Limit State Model Basis for Assessment of Offshore Wind Energy Converters

    DEFF Research Database (Denmark)

    Thöns, Sebastian; Faber, M. H.; Rücker, W.

    2012-01-01

    then in combina-tion with the ultimate limit state requirements leads to the specific constitutive relations. As a result finite element models based on shell elements incorporating a structural and a loading model are introduced and described in detail. Applying these models the ultimate capacity of the support...... on the basis of literature review and measurement data from a prototype Multibrid M5000 support structure. In combination with the developed structural and loading models, sensitivity analyses in regard to the responses are peiformed to enhance the understanding and to refine the developed models. To this end...... variables on the responses including nonlinearity the refinement of the model is performed on a quantitative basis....

  3. Evaluation of time-accelerated irradiation method of elastomer by modulus-ultimate elongation profile

    International Nuclear Information System (INIS)

    Ito, Masayuki; Oka, Toshitaka; Hama, Yosimasa

    2009-01-01

    'Generalized modulus-ultimate elongation profile' was induced from the relationship between the modulus and the ultimate elongation of an elastomer that was quantitatively added crosslinking and scission. This profile can be used to evaluate the time-accelerated irradiation methods of ethylene-propylene-diene elastomer. The irradiation under low dose rate (0.33 kGy/h) at room temperature was the reference condition. The short-time irradiation condition was 4.2 kGy/h in 0.5 MPa oxygen at room temperature and 5.0 kGy/h in air at 70 o C. The former tended to bring about the higher ratio of scission than the reference condition; the latter tended to bring about the higher ratio of crosslinking.

  4. Out-of-plane ultimate shear strength of RC mat-slab foundations

    International Nuclear Information System (INIS)

    Kumagai, Hitoshi; Nukui, Yasushi; Imamura, Akira; Terayama, Takeshi; Hagiwara, Tetsuya; Kojima, Isao

    2011-01-01

    There have been few studies on the out-of-plane shear in RC mat-slab foundations, and the reasonable method has been demanded to estimate ultimate shear strength of RC mat-slab foundations in the nuclear facilities. In the previous study, the out-of-plane loading tests on the 20 square slab specimens had been performed to collect the fundamental data. In this study, the test results were successfully predicted by 3D non-linear Finite Element Analysis. It has been confirmed that the ultimate shear stress in the slab specimen can be estimated by the Arakawa's formula, which is commonly used to estimate the shear strength of RC beams. (author)

  5. Ultimate analysis of PWR prestressed concrete containment subjected to internal pressure

    International Nuclear Information System (INIS)

    Hu, H.-T.; Lin, Y.-H.

    2006-01-01

    Numerical analyses are carried out by using the ABAQUS finite element program to predict the ultimate pressure capacity and the failure mode of the PWR prestressed concrete containment at Maanshan nuclear power plant. Material nonlinearity such as concrete cracking, tension stiffening, shear retention, concrete plasticity, yielding of prestressing tendon, yielding of steel reinforcing bar and degradation of material properties due to high temperature are all simulated with proper constitutive models. Geometric nonlinearity due to finite deformation has also been considered. The results of the analysis show that when the prestressed concrete containment fails, extensive cracks take place at the apex of the dome, the junction of the dome and cylinder, and the bottom of the cylinder connecting to the base slab. In addition, the ultimate pressure capacity of the containment is higher than the design pressure by 86%

  6. Nonlinear finite element analysis of nuclear reinforced prestressed concrete containments up to ultimate load capacity

    International Nuclear Information System (INIS)

    Gupta, A.; Singh, R.K.; Kushwaha, H.S.; Mahajan, S.C.; Kakodkar, A.

    1996-01-01

    For safety evaluation of nuclear structures a finite element code ULCA (Ultimate Load Capacity Assessment) has been developed. Eight/nine noded isoparametric quadrilateral plate/shell element with reinforcement as a through thickness discrete but integral smeared layer of the element is presented to analyze reinforced and prestressed concrete structures. Various constitutive models such as crushing, cracking in tension, tension stiffening and rebar yielding are studied and effect of these parameters on the reserve strength of structures is brought out through a number of benchmark tests. A global model is used to analyze the prestressed concrete containment wall of a typical 220 MWe Pressurized Heavy Water Reactor (PHWR) up to its ultimate capacity. This demonstrates the adequacy of Indian PHWR containment design to withstand severe accident loads

  7. Qualtum cosmics-and-chaotics--the ultimate tortoise in physics and modern medicine.

    Directory of Open Access Journals (Sweden)

    Kothari M

    1997-10-01

    Full Text Available Qualtum cosmics is the qualitative opposite of quantum mechanics. The flip-side of qualtum cosmics is qualtum chaotics, the two governing much of what is seen as inscrutable in medicine. The Ultimate (Last Tortoise is close to Einsteinean idea of a Unified Theory, a single concept that can explain whatsoever there is in physics, (and in medicine, or what have you.

  8. Utilization of metal scrap for the production of waste drums for ultimate disposal

    International Nuclear Information System (INIS)

    Janberg, K.; Rittscher, D.

    1988-01-01

    The contribution reviews the history of development of the techniques for treatment of decommissioning scrap from the beginning of the 1980's onwards (decommissioning of the Niederaichbach and Gundremmingen nuclear power stations), together with the radiological measuring methods required for regulatory purposes. The advantages of the recycling of the metal scrap by means of melting, and of materials utilization for production of waste containers for ultimate storage are discussed together with product quality assurance criteria. (RB) [de

  9. The Influence of Wagon Structure Part Shape Optimization on Ultimate Fatigue Strength

    OpenAIRE

    Milovanović, Vladimir; Živković, Miroslav; Jovičić, Gordana; Živković, Jelena; Kozak, Dražan

    2016-01-01

    This study investigates how shape optimisation affects the ultimate fatigue strength of a mechanical part. The mechanical part chosen for this investigation is an axle guard of running gear elements of the Hccrrs 2x2 axle car-carrying wagon. The static and fatigue strength analysis procedure according to the UIC 517 standard and numerical methods have been applied. Material properties were determined experimentally and the necessary numerical calculations were performed by using the finite el...

  10. The ultimate safe (US) Reactor: A concept for the third millenium

    International Nuclear Information System (INIS)

    Gat, U.

    1986-01-01

    The Ultimate Safe (U.S.) Reactor is based on a novel safety concept. Fission products in the reactor are allowed to accumulate only to a level at which they would constitute a harmless source term. Removal of fission products also removes the decay heat - the driving force for the source term. The reactor has no excess criticality and is controlled by the reactivity temperature coefficient. Safety is inherent and passive. Waste is removed from the site promptly

  11. Modeling and simulation of loss of the ultimate heat sink in a typical material testing reactor

    International Nuclear Information System (INIS)

    El-Khatib, Hisham; El-Morshedy, Salah El-Din; Higazy, Maher G.; El-Shazly, Karam

    2013-01-01

    Highlights: ► A thermal–hydraulic model has been developed to simulate loss of the ultimate heat sink in MTR. ► The model involves three coupled sub-models for core, heat exchanger and cooling tower. ► The model is validated against PARET for steady-state and verified by operation data for transients. ► The model is used to simulate the behavior of the reactor under a loss of the ultimate heat sink. ► The model results are analyzed and discussed. -- Abstract: A thermal–hydraulic model has been developed to simulate loss of the ultimate heat sink in a typical material testing reactor (MTR). The model involves three interactively coupled sub-models for reactor core, heat exchanger and cooling tower. The model is validated against PARET code for steady-state operation and verified by the reactor operation records for transients. Then, the model is used to simulate the thermal–hydraulic behavior of the reactor under a loss of the ultimate heat sink event. The simulation is performed for two operation regimes: regime I representing 11 MW power and three cooling tower cells operated, and regime II representing 22 MW power and six cooling tower cells operated. In regime I, the simulation is performed for 1, 2 and 3 cooling tower cells failed while in regime II, it is performed for 1, 2, 3, 4, 5 and 6 cooling tower cells failed. The simulation is performed under protected conditions where the safety action called power reduction is triggered by reactor protection system to decrease the reactor power by 20% when the coolant inlet temperature to the core reaches 43 °C and scram is triggered if the core inlet temperature reaches 44 °C. The model results are analyzed and discussed.

  12. Tasks of radiation protection in the centralized collection and ultimate disposal of radioactive waste

    International Nuclear Information System (INIS)

    Boerst, F.M.; Fasten, C.; Koerner, W.; Oppermann, U.; Werner, H.J.; Zappe, D.

    1988-01-01

    In the GDR, the ERAM (Endlager fuer radioaktive Abfaelle, Morsleben), an operating unit of Volkseigenes Kombinat Kernkraftwerke 'Bruno Leuschner' in Greifswald, is responsible for the central collection and ultimate disposal of radioactive waste. From the licensing body's point of view an assessment is given of the legislation for radioactive wastes, especially as to their collection, transport to and handling in the final repository. As a result, some conclusions are drawn concerning future work in this field. 9 tabs., 34 refs. (author)

  13. Effects of urbanization on animal behaviour : patterns, underlying mechanisms and ultimate causes

    OpenAIRE

    Miranda, Ana Catarina Sequeira Nunes Coutinho de

    2014-01-01

    Human-altered environmental conditions affect many species at the global scale. An extreme form of anthropogenic alteration is the existence and rapid increase of urban areas. A key question is how animals cope with urbanization. In order to live in cities, animals have to adjust their behaviour and life histories to the urban novel environment.The main objectives of this thesis were to investigate (i) the existence of behavioural changes related to the urbanization process, (ii) the ultimate...

  14. Dual characteristics of yield and ultimate strength as applied to two grades of beryllium

    International Nuclear Information System (INIS)

    Priddy, T.G.; Benzley, S.E.; Johnson, R.L.

    1977-02-01

    Published yield and ultimate biaxial strength data for two grades of beryllium are correlated with the use of a macroscopic failure model. Cross sections of the resulting surfaces in three-dimensional stress space are drawn to illustrate the expected transition from ductile to brittle fracture for triaxial tension states of stress. The usefulness of these models to the prediction of fracture in ductile materials is discussed. 5 tables, 8 figures, 11 references

  15. Palynological Investigation of the Holocene Thermal Optimum in New Zealand

    Science.gov (United States)

    Newnham, R. M.; McGlone, M. S.; Wilmshurst, J. M.

    2005-12-01

    It has long been assumed in New Zealand (NZ) that the Holocene Thermal Optimum (HTO) occurred at the beginning of the Holocene. Nearly 40 years ago, Hendy and Wilson pioneered the use of 18O/16O composition of calcite in NZ speleothems to reconstruct past climate and in so doing showed an HTO occurring earlier in NZ than in comparable Northern Hemisphere records (Hendy & Wilson,1968). More recent work on NZ speleothems (Williams et al., 2005) corroborates the concept of an early HTO dated between ca 11.7 and 10.6 ka, but there is no definitive description of the event as a NZ-wide phenomenon, no intensive dating of it, nor temperature quantification. Moreover, there is no firm conclusion as to whether it is registered consistently between different proxies and across NZ regions. Until recently, attempts to quantify past climate change from NZ pollen data have been hindered by failure to demonstrate robust relationships between modern pollen assemblages and climate due, it is thought, to strong anthropogenic modification of natural vegetation patterns and steep climatic gradients (Norton et al., 1986). However, as deforestation commenced only ca 700 years ago, and is unambiguously detected in pollen records from throughout NZ, an almost unique opportunity exists to develop pollen-climate transfer functions using pre-human pollen-vegetation sources. McGlone and Wilmshurst have assembled an extensive (138-site) `modern' pollen database, based on ca 700 yr BP pre-deforestation pollen assemblages from peat and lake cores. This now provides a basis for more secure pollen-climate reconstruction than hitherto has been possible. Statistical modelling of the environmental determinants of patterns in the pre-deforestation pollen database indicates the strongest relationship (r2 > 0.8) is with Mean Annual Temperature (MAT) and suggests that this parameter can be reliably reconstructed, with error estimates, from Late Quaternary NZ pollen profiles. We use this database to

  16. Optimum gas turbine cycle for combined cycle power plant

    International Nuclear Information System (INIS)

    Polyzakis, A.L.; Koroneos, C.; Xydis, G.

    2008-01-01

    The gas turbine based power plant is characterized by its relatively low capital cost compared with the steam power plant. It has environmental advantages and short construction lead time. However, conventional industrial engines have lower efficiencies, especially at part load. One of the technologies adopted nowadays for efficiency improvement is the 'combined cycle'. The combined cycle technology is now well established and offers superior efficiency to any of the competing gas turbine based systems that are likely to be available in the medium term for large scale power generation applications. This paper has as objective the optimization of a combined cycle power plant describing and comparing four different gas turbine cycles: simple cycle, intercooled cycle, reheated cycle and intercooled and reheated cycle. The proposed combined cycle plant would produce 300 MW of power (200 MW from the gas turbine and 100 MW from the steam turbine). The results showed that the reheated gas turbine is the most desirable overall, mainly because of its high turbine exhaust gas temperature and resulting high thermal efficiency of the bottoming steam cycle. The optimal gas turbine (GT) cycle will lead to a more efficient combined cycle power plant (CCPP), and this will result in great savings. The initial approach adopted is to investigate independently the four theoretically possible configurations of the gas plant. On the basis of combining these with a single pressure Rankine cycle, the optimum gas scheme is found. Once the gas turbine is selected, the next step is to investigate the impact of the steam cycle design and parameters on the overall performance of the plant, in order to choose the combined cycle offering the best fit with the objectives of the work as depicted above. Each alterative cycle was studied, aiming to find the best option from the standpoint of overall efficiency, installation and operational costs, maintainability and reliability for a combined power

  17. Nuclear fusion ion beam source composed of optimum channel wall

    International Nuclear Information System (INIS)

    Furukaw, T.

    2007-01-01

    Full text of publication follows: Numerical and experimental researches of the hall-type beam accelerator was conducted by highlighting both neutral species and material of acceleration channel wall. The hall-type beam accelerator is expected as ion beam source for nuclear fusion since it could product ion beam density over 10 3 times as high as that of electrostatic accelerator, which is used regularly as beam heating device, because it is proven that the beam heating method could accelerate ion to high energy beam by electric field and heat plasma to ultra high temperature of 100 million degrees or more. At high-voltage mode of DC regime that is normal operational condition, however, the various plasma MHD (magneto-hydrodynamic) instabilities are generated. In particular, the large-amplitude and low-frequency plasma MHD instability in the tens of kHz among them has been a serious problem that should be solved to improve the operational stability and the system durability. So, we propose a hall-type beam accelerator with new design concepts; both acquisition of simultaneous solution for reducing the plasma MHD instability and the accelerator core overheating and optimum combination of the acceleration channel wall material. The technologies for this concept are as follows: 1) To increase neutral species velocity-inlet in acceleration channel by preheating propellant through circularly propellant conduit line inside accelerator system could bring about the lower amplitude of the instability. 2) Through this method, the accelerator system is cooled, and the higher thrust and specific-impulse is produced with hardly changing thrust efficiency at the same time. 3) To select BN (Boron- Nitride) and Al 2 O 3 as wall material of ionization- and acceleration-zone in acceleration channel respectively having different secondary-electron emission-coefficient could achieve the higher-efficiency and -durability. The hall-type beam accelerator designed using these technologies

  18. Numerical Study on Ultimate Behaviour of Bolted End-Plate Steel Connections

    Directory of Open Access Journals (Sweden)

    R.E.S. Ismail

    Full Text Available Abstract Bolted end-plate steel connections have become more popular due to ease of fabrication. This paper presents a three dimension Finite Element Model (FEM, using the multi-purpose software ABAQUS, to study the effect of different geometrical parameters on the ultimate behavior of the connection. The proposed model takes into account material and geometrical non-linearities, initial imperfection, contact between adjacent surfaces and the pretension force in the bolts. The Finite Element results are calibrated with published experimental results ''briefly reviewed in this paper'' and verified that the numerical model can simulate and analyze the overall and detailed behavior of different types of bolted end-plate steel connections. Using verified FEM, parametric study is then carried out to study the ultimate behavior with variations in: bolt diameter, end-plate thickness, length of column stiffener, angle of rib stiffener. The results are examined with respect to the failure modes, the evolution of the resistance, the initial stiffness, and the rotation capacity. Finally, the ultimate behavior of the bolted end-plate steel connection is discussed in detail, and recommendations for the design purpose are made.

  19. Methodology for predicting ultimate pressure capacity of the ACR-1000 containment structure

    International Nuclear Information System (INIS)

    Saudy, A.M.; Awad, A.; Elgohary, M.

    2006-01-01

    The Advanced CANDU Reactor or the ACR-1000 is developed by Atomic Energy of Canada Limited (AECL) to be the next step in the evolution of the CANDU product line. It is based on the proven CANDU technology and incorporates advanced design technologies. The ACR containment structure is an essential element of the overall defense in depth approach to reactor safety, and is a physical barrier against the release of radioactive material to the environment. Therefore, it is important to provide a robust design with an adequate margin of safety. One of the key design requirements of the ACR containment structure is to have an ultimate pressure capacity that is at least twice the design pressure Using standard design codes, the containment structure is expected to behave elastically at least up to 1.5 times the design pressure. Beyond this pressure level, the concrete containment structure with reinforcements and post-tension tendons behaves in a highly non-linear manner and exhibits a complex response when cracks initiate and propagate. To predict the structural non-linear responses, at least two critical features are involved. These are: the structural idealization by the geometry and material property models, and the adopted solution algorithm. Therefore, detailed idealization of the concrete structure is needed in order to accurately predict its ultimate pressure capacity. This paper summarizes the analysis methodology to be carried out to establish the ultimate pressure capacity of the ACR containment structure and to confirm that the structure meets the specified design requirements. (author)

  20. Transition to the Ultimate Regime in Two-Dimensional Rayleigh-Bénard Convection

    Science.gov (United States)

    Zhu, Xiaojue; Mathai, Varghese; Stevens, Richard J. A. M.; Verzicco, Roberto; Lohse, Detlef

    2018-04-01

    The possible transition to the so-called ultimate regime, wherein both the bulk and the boundary layers are turbulent, has been an outstanding issue in thermal convection, since the seminal work by Kraichnan [Phys. Fluids 5, 1374 (1962), 10.1063/1.1706533]. Yet, when this transition takes place and how the local flow induces it is not fully understood. Here, by performing two-dimensional simulations of Rayleigh-Bénard turbulence covering six decades in Rayleigh number Ra up to 1 014 for Prandtl number Pr =1 , for the first time in numerical simulations we find the transition to the ultimate regime, namely, at Ra*=1013 . We reveal how the emission of thermal plumes enhances the global heat transport, leading to a steeper increase of the Nusselt number than the classical Malkus scaling Nu ˜Ra1 /3 [Proc. R. Soc. A 225, 196 (1954), 10.1098/rspa.1954.0197]. Beyond the transition, the mean velocity profiles are logarithmic throughout, indicating turbulent boundary layers. In contrast, the temperature profiles are only locally logarithmic, namely, within the regions where plumes are emitted, and where the local Nusselt number has an effective scaling Nu ˜Ra0.38 , corresponding to the effective scaling in the ultimate regime.

  1. Ultimate strength analysis of ring-stiffened cylinders subjected to hydrostatic pressure

    International Nuclear Information System (INIS)

    Park, Chi Mo

    1990-01-01

    In this study, ultimate strength analysis of ring-stiffened cylinders have been performed, considering the elasto-plastic large deflection. In the elasto-plastic analysis, von Mises yield criteria, the plastic flow theory and the layered approach have been adopted. In order to take into account the follower force effect of the hydrostatic pressure, the incremental load components have been updated at every loading step. As collapse modes, axisymmetric yielding, interframe shell buckling and general buckling are considered, while local buckling of ring-stiffener is not considered. Initial shape imperfection is assumed to be the elastic buckling mode to obtain the lower bound of the ultimate strength. Results of numerical analysis are compared with the experimental results to show the validity of the present approach. It has been drawn that the present numerical results are closely correlated with the experimental results. On the other hand, the effects of initial shape imperfection and condition on the ultimate strength have been investigated. (Author)

  2. Optimum Peak Current Hysteresis Control for Energy Recovering Converter in CDI Desalination

    Directory of Open Access Journals (Sweden)

    Alberto M. Pernía

    2014-06-01

    Full Text Available Capacitive De-Ionization (CDI is becoming a suitable alternative for desalination. The low cost of the materials required and its reduced energy consumption can be critical factors for developing this technique. CDI technology does not require a high-pressure system and the energy storage capability of CDI cells allows it to be reused in other CDI cells, thus minimizing consumption. The goal of the power stage responsible of the energy recovery is transferring the stored energy from one cell to another with the maximum possible efficiency, thus allowing the desalination process to continue. Assuming hysteresis current control is implemented at the DC/DC (direct current converter, this paper aims to determine the optimum peak current through the inductor in each switching period with a view to maximizing overall efficiency. The geometrical parameters of the desalination cell and the NaCl concentration modify the cell electrical properties. The peak current control of the power stage should be adapted to the cell characteristics so that the efficiency behavior of the whole CDI system can be improved. The mathematical model defined in this paper allows the CDI plant automation using the peak inductor current as control variable, adapting its value to the salt concentration during the desalination process.

  3. Defining and Differentiating the Makerspace

    Science.gov (United States)

    Dousay, Tonia A.

    2017-01-01

    Many resources now punctuate the maker movement landscape. However, some schools and communities still struggle to understand this burgeoning movement. How do we define these spaces and differentiate them from previous labs and shops? Through a multidimensional framework, stakeholders should consider how the structure, access, staffing, and tools…

  4. Indico CONFERENCE: Define the Programme

    CERN Multimedia

    CERN. Geneva; Ferreira, Pedro

    2017-01-01

    In this tutorial you are going to learn how to define the programme of a conference in Indico. The program of your conference is divided in different “tracks”. Tracks represent the subject matter of the conference, such as “Online Computing”, “Offline Computing”, and so on.

  5. Optimum plastic scintillator and optical fiber combination for brachytherapy dosimetry

    International Nuclear Information System (INIS)

    Arnfield, Mark R.; Gaballa, Hani E.; Zwicker, Robert D.; Islam, Quazi; Schmidt-Ullrich, Rupert

    1995-01-01

    Purpose/Objective: There have been several recent reports using plastic scintillators to measure dose in photon and electron beams. External beam measurements agreed well with standard ion chamber dosimetry. This was implemented by using two identical, parallel optical fibers with a small piece of plastic scintillator attached to one. We have constructed a similar device for application to brachytherapy. Brachytherapy dosimetry is a more difficult problem than external beam because of high dose gradients and widely ranging photon energies. Based on detailed spectral measurements, we have designed a dosimeter specifically to meet the unique, stringent needs of brachytherapy. Materials and Methods: The work consisted of two stages. In the first stage, we measured the optical spectra emitted by commercial plastic scintillators and silica core optical fibers in the presence of a 10 Curie iridium 192 HDR source. In the second stage, the spectral information was used to select an optimum combination of scintillator and fiber which were incorporated in the dosimeter. Equipment for the spectral measurements included a 0.1 meter monochromator with a sensitive photomultiplier (PMT) with flat response across the visible. The resolution of spectral scans was 4 nm. The dosimeter was constructed with a 1mm x 3mm piece of plastic scintillator bonded with optical cement to a 0.6 mm diameter silica core optical fiber. A second, identical optical fiber running alongside the first, with no scintillator attached, was used for background subtraction. Two PMTs with high sensitivity in the visible were used at the fiber distal ends. There was a space for an optical filter between the fiber and the PMTs, whose purpose is described below. The PMTs were connected to a differential pair whose output was transferred to a current source for measurement by a standard electrometer. Results: The scintillation spectra of six different types of silica core optical fibers in the presence of the

  6. A techno-economic model for optimum regeneration of surface mined land

    Science.gov (United States)

    Mukhopadhyay, Manas K.; Sinha, Indra N.

    2006-07-01

    The recent global scenario in the mineral sector may be characterized by rising competitiveness, increasing production costs and a slump in market price. This has pushed the mineral sector in general and that in the developing countries in particular to a situation where the industry has a limited capacity to sustain unproductive costs. This, more often than not, results in a situation where the industry fails to ensure environmental safeguards during and after mineral extraction. The situation is conspicuous in the Indian coal mining industry where more than 73% production comes from surface operations. India has an ambitious power augmentation projection for the coming 10 years. A phenomenal increase in coal production is proposed from the power grade coalfields in India. One of the most likely fall-outs of land degradation due to mining in these areas would be significant reduction of agricultural and other important land-uses. Currently, backfilling costs are perceived as prohibitive and abandonment of land is the easy way out. This study attempts to provide mine planners with a mathematical model that distributes generated overburden at defined disposal options while ensuring maximization of backfilled land area at minimum direct and economic costs. Optimization has been accomplished by linear programming (LP) for optimum distribution of each year’s generated overburden. Previous year’s disposal quantity outputs are processed as one set of the inputs to the LP model for generation of current year’s disposal output. From various geo-mining inputs, site constants of the LP constraints are calculated. Arrived value of economic vectors, which guide the programming statement, decides the optimal overburden distribution in defined options. The case example (with model test run) indicates that overburden distribution is significantly sensitive to coal seam gradient. The model has universal applicability to cyclic system (shovel dumper combination) of opencast

  7. Radiographic testing - optimum radiographs of plastics and composite materials with dosimeter control

    International Nuclear Information System (INIS)

    Kuster, J.

    1978-01-01

    In view of great differencies in X-ray transmission it is more difficult to get optimum radiographs of plastics and especially of reinforced plastics than for example of metals. A procedure will be reported how to get with little effort optimum radiographs especially also in the range of long wavelength radiation corresponding 10 to 25 kV.P. (orig.) [de

  8. The refining of soybean oil to optimum quality

    Directory of Open Access Journals (Sweden)

    Rusell, J.

    1996-08-01

    Full Text Available One of the objectives of the American Soybean Association is to improve the quality of soybean and related products in Turkey. In order to achieve this, a number of extraction plants and refineries were visited to enable first hand information to be obtained on the type of equipment used in all unit processes, the methodology employed, quality standards and levels of efficiency. The culmination of the visit was a seminar organised jointly by the American Soybean Association and the Turkish Vegetable Oil Association in Istanbul on 22nd September 1989, at which a paper with the above title was presented. A reproduction of this paper is attached which briefly describes the critical areas of soybean oil processing and includes recommendations for quality improvements. It concludes with the comment that provided proper care is taken and optimum refining processes employed, including hydrogenation where appropriate, an impressive range of oils, margarines and shortenings of high quality can ben produced. The author would like to record his grateful thanks to Dr. R. Leysen of the American Soybean Association for all his help and guidance, to Mr. Kenon Marasoglu, Chairman of the Turkish Vegetable Oil Association and to the management and staff of all the factories visited. Acknowledgement is also made to Dr. D. R. Arickson and Mr. L. H. Wiedermann of the American Soybean Association for the use of some technical information from a paper entitled «Soybean Oil-Modern Processing and Utilisation» which is to be published shortly.

    Uno de los objetivos de la Asociación Americana de Soja en Turquía es mejorar la calidad de la soja y de los productos relacionados. En orden a conseguir esto, diversas plantas de extracción y refinerías fueron visitadas para permitir obtener de primera mano información sobre el tipo de equipo usado en todas las unidades de proceso, la metodología empleada, los estándar de calidad y los niveles de eficacia. La

  9. AIDS defining disease: Disseminated cryptococcosis

    Directory of Open Access Journals (Sweden)

    Roshan Anupama

    2006-01-01

    Full Text Available Disseminated cryptococcosis is one of the acquired immune deficiency syndrome defining criteria and the most common cause of life threatening meningitis. Disseminated lesions in the skin manifest as papules or nodules that mimic molluscum contagiosum (MC. We report here a human immunodeficiency virus positive patient who presented with MC like lesions. Disseminated cryptococcosis was confirmed by India ink preparation and histopathology. The condition of the patient improved with amphotercin B.

  10. How do people define moderation?

    Science.gov (United States)

    vanDellen, Michelle R; Isherwood, Jennifer C; Delose, Julie E

    2016-06-01

    Eating in moderation is considered to be sound and practical advice for weight maintenance or prevention of weight gain. However, the concept of moderation is ambiguous, and the effect of moderation messages on consumption has yet to be empirically examined. The present manuscript examines how people define moderate consumption. We expected that people would define moderate consumption in ways that justified their current or desired consumption rather than view moderation as an objective standard. In Studies 1 and 2, moderate consumption was perceived to involve greater quantities of an unhealthy food (chocolate chip cookies, gummy candies) than perceptions of how much one should consume. In Study 3, participants generally perceived themselves to eat in moderation and defined moderate consumption as greater than their personal consumption. Furthermore, definitions of moderate consumption were related to personal consumption behaviors. Results suggest that the endorsement of moderation messages allows for a wide range of interpretations of moderate consumption. Thus, we conclude that moderation messages are unlikely to be effective messages for helping people maintain or lose weight. Copyright © 2016 Elsevier Ltd. All rights reserved.

  11. 15 CFR Supplement No. 3 to Part 748 - BIS-711, Statement by Ultimate Consignee and Purchaser Instructions

    Science.gov (United States)

    2010-01-01

    ...” include: contractual, franchise, distributor, wholesaler, continuing and regular individual business, etc... persons, other than employees of the ultimate consignee or purchaser, who assisted in the preparation of...

  12. Defining Success in Open Science.

    Science.gov (United States)

    Ali-Khan, Sarah E; Jean, Antoine; MacDonald, Emily; Gold, E Richard

    2018-01-01

    Mounting evidence indicates that worldwide, innovation systems are increasing unsustainable. Equally, concerns about inequities in the science and innovation process, and in access to its benefits, continue. Against a backdrop of growing health, economic and scientific challenges global stakeholders are urgently seeking to spur innovation and maximize the just distribution of benefits for all. Open Science collaboration (OS) - comprising a variety of approaches to increase open, public, and rapid mobilization of scientific knowledge - is seen to be one of the most promising ways forward. Yet, many decision-makers hesitate to construct policy to support the adoption and implementation of OS without access to substantive, clear and reliable evidence. In October 2017, international thought-leaders gathered at an Open Science Leadership Forum in the Washington DC offices of the Bill and Melinda Gates Foundation to share their views on what successful Open Science looks like. Delegates from developed and developing nations, national governments, science agencies and funding bodies, philanthropy, researchers, patient organizations and the biotechnology, pharma and artificial intelligence (AI) industries discussed the outcomes that would rally them to invest in OS, as well as wider issues of policy and implementation. This first of two reports, summarizes delegates' views on what they believe OS will deliver in terms of research, innovation and social impact in the life sciences. Through open and collaborative process over the next months, we will translate these success outcomes into a toolkit of quantitative and qualitative indicators to assess when, where and how open science collaborations best advance research, innovation and social benefit. Ultimately, this work aims to develop and openly share tools to allow stakeholders to evaluate and re-invent their innovation ecosystems, to maximize value for the global public and patients, and address long-standing questions

  13. Ultimate Electrical Means for Severe Accident and Multi Unit Event Management

    International Nuclear Information System (INIS)

    Guisez, Xavier

    2015-01-01

    Following the Multi Unit Severe Accident that occurred at Fukushima as a result of the tsunami on 11 March 2011, the European Council decided to submit its Nuclear Power Plants to a Stress Test. In Belgium, this Stress Test, named BEST (Belgian Stress Test), was successfully concluded at the end of 2011. Nevertheless, Electrabel decided, in agreement with the Authorities, to start a beyond design basis action plan, with the goal to mitigate the consequences of a Beyond Design Basis Accident and a Multi Unit Event. Consequently, this has led to an improvement of the robustness of its Nuclear Power Plants. Considering the importance of electrical power supply to a nuclear power plant, a significant part of this action plan consisted of setting up a mobile, 'plug and play' method for the electrical power supply to some major safety systems. In order to install this ultimate power supply, three factors were retained as essential. First, important reactor monitoring instrumentation is preserved. Second, core cooling is provided at all times. Finally, systems are easily made operational within a very short delay of time. During normal operation and Design Basis Events, core cooling is provided by High Voltage equipment. However, during high stress circumstances, it is too complex to realize connections on this equipment. Therefore, analysis was performed to realize core cooling with, easier to handle, Low Voltage equipment. These systems are powered by several GenSets, especially designed and manufactured for this application. The outcome of this project are easy to use, ultimate means, that supply electric power to important safety systems in order to drastically reduce the risk of core damage, during a beyond design basis event. Additionally, for all ultimate means, procedures and training modules were developed for the operators. (authors)

  14. Ultimate pressures achieved in TiZrV sputter-coated vacuum chambers

    CERN Document Server

    Benvenuti, Cristoforo; Ruzinov, V

    2001-01-01

    Two metre long, cylindrical vacuum chambers of diameter ranging from 34 to 100 mm, coated with TiZrV getter films by sputtering, have been baked for about 24 h at temperatures from 120 to 250 degrees C. The ultimate pressures achieved after bakeout were found to correspond to the ratio of the pressure gauge degassing to the effective pumping speed provided by the chamber at the location of the gauge. The results covering a pressure range from 10/sup -11/ Torr down to 10 /sup -13/ Torr are presented and discussed. (6 refs).

  15. DHC in Helsinki - The Ultimate Heating and Cooling Solution for a Large Urban Area

    Energy Technology Data Exchange (ETDEWEB)

    Wirgentius, Niko; Riipinen, Marko

    2010-09-15

    Since the 1950s there has been successful district energy business in Helsinki. It has been the main factor for superior energy efficiency and low CO2 emissions both in heating and cooling as well as providing clean air for the metropolitan area. The system has been grown by commercial basis based on customers' own willingness to select district energy solution. It also provided a profitable energy business to local energy company, Helsinki Energy. Helsinki DHC system is a good example of ultimate urban energy solution that provides benefits for the customer, energy company, metropolitan area and for the whole society as well.

  16. Investigations on the ultimate compressive strength of composite plates with geometrical imperfections

    DEFF Research Database (Denmark)

    Misirlis, K.; Downes, J.; Dow, R.S.

    2009-01-01

    with initial geometric imperfections. This paper presents the validation of finite element models against a series of plate tests that were performed within this framework and parametric studies that were carried out to identify the effects of geometric imperfections on the ultimate compressive strength......A series of studies has been performed within the MARSTRUCT Network of Excellence on Marine Structures in order to investigate the buckling response of glass fibre reinforced polymer plates. These studies include the fabrication, testing and finite element analysis of a large number of plates...

  17. Lava ultimate resin nano ceramic for CAD/ CAM: customization case study.

    Science.gov (United States)

    Koller, M; Arnetzl, G V; Holly, L; Arnetzl, G

    2012-01-01

    Lava Ultimate Resin Nano Ceramic (RNC) blocks are innovative new CAD/CAM materials that make it possible to achieve superior esthetic results in easy steps. The blocks are made of nano ceramic particles embedded in a highly cured resin matrix. Therefore, composite materials can be used to characterize and adjust resin nano ceramic restorations after milling. The milled RNC restorations can be individualized intra-orally or extra-orally, either before or after insertion. Unlike conventional ceramic restorations, customization and glaze firing is neither necessary nor possible with RNC restorations. This opens up the opportunity for intraoral individualization and adaptation of the restorations.

  18. Reflecting on impact, changes and continuities: restructuring workplace cultures: the ultimate work-family challenge.

    OpenAIRE

    Lewis, Suzan

    2010-01-01

    Purpose – The purpose of this paper is to reflect on the paper “Restructuring workplace cultures: the ultimate work-family challenge?” is published in Women in Management Review, Vol. 16 No. 1, 2001, pp. 21-9. \\ud \\ud Design/methodology/approach – The impact of the paper is considered within a framework that takes account of national discursive and political contexts in the UK in 2001 and in the present and uses a gendered organisation lens. \\ud \\ud Findings – The 2001 paper demonstrates that...

  19. The legal ensurance of underground ultimate storage of radioactive wastes without risk

    International Nuclear Information System (INIS)

    Prasse, R.

    1974-01-01

    1. The legal position towards the property owner: a) with a view to the freedom of property claim, b) in the light of the influence of the property owner. 2. The legal position towards the neighbouring property owners: a) resistance rights of the body corporate responsible for the ultimate storage, b) resistance rights of the neighbouring property owner. 3. The legal position towards those authorized to mine: a) mining free minerals, b) mining minerals reserved for the state. 4. The legal position towards prospectors. (orig./HP) [de

  20. Seismic proving test of ultimate piping strength (current status of preliminary tests)

    International Nuclear Information System (INIS)

    Suzuki, K.; Namita, Y.; Abe, H.; Ichihashi, I.; Suzuki, K.; Ishiwata, M.; Fujiwaka, T.; Yokota, H.

    2001-01-01

    In 1998 Fiscal Year, the 6 year program of piping tests was initiated with the following objectives: i) to clarify the elasto-plastic response and ultimate strength of nuclear piping, ii) to ascertain the seismic safety margin of the current seismic design code for piping, and iii) to assess new allowable stress rules. In order to resolve extensive technical issues before proceeding on to the seismic proving test of a large-scale piping system, a series of preliminary tests of materials, piping components and simplified piping systems is intended. In this paper, the current status of the material tests and the piping component tests is reported. (author)

  1. A New Algorithm for Determining Ultimate Pit Limits Based on Network Optimization

    OpenAIRE

    Ali Asghar Khodayari

    2013-01-01

    One of the main concerns of the mining industry is to determine ultimate pit limits. Final pit is a collection of blocks, which can be removed with maximum profit while following restrictions on the slope of the mine’s walls. The size, location and final shape of an open-pit are very important in designing the location of waste dumps, stockpiles, processing plants, access roads and other surface facilities as well as in developing a production program. There are numerous methods for designing...

  2. Network Coded Software Defined Networking

    DEFF Research Database (Denmark)

    Krigslund, Jeppe; Hansen, Jonas; Roetter, Daniel Enrique Lucani

    2015-01-01

    Software Defined Networking (SDN) and Network Coding (NC) are two key concepts in networking that have garnered a large attention in recent years. On the one hand, SDN's potential to virtualize services in the Internet allows a large flexibility not only for routing data, but also to manage....... This paper advocates for the use of SDN to bring about future Internet and 5G network services by incorporating network coding (NC) functionalities. The inherent flexibility of both SDN and NC provides a fertile ground to envision more efficient, robust, and secure networking designs, that may also...

  3. Network Coded Software Defined Networking

    DEFF Research Database (Denmark)

    Hansen, Jonas; Roetter, Daniel Enrique Lucani; Krigslund, Jeppe

    2015-01-01

    Software defined networking has garnered large attention due to its potential to virtualize services in the Internet, introducing flexibility in the buffering, scheduling, processing, and routing of data in network routers. SDN breaks the deadlock that has kept Internet network protocols stagnant...... for decades, while applications and physical links have evolved. This article advocates for the use of SDN to bring about 5G network services by incorporating network coding (NC) functionalities. The latter constitutes a major leap forward compared to the state-of-the- art store and forward Internet paradigm...

  4. (Re)Defining Salesperson Motivation

    DEFF Research Database (Denmark)

    Khusainova, Rushana; de Jong, Ad; Lee, Nick

    2018-01-01

    The construct of motivation is one of the central themes in selling and sales management research. Yet, to-date no review article exists that surveys the construct (both from an extrinsic and intrinsic motivation context), critically evaluates its current status, examines various key challenges...... apparent from the extant research, and suggests new research opportunities based on a thorough review of past work. The authors explore how motivation is defined, major theories underpinning motivation, how motivation has historically been measured, and key methodologies used over time. In addition......, attention is given to principal drivers and outcomes of salesperson motivation. A summarizing appendix of key articles in salesperson motivation is provided....

  5. Defining Usability of PN Services

    DEFF Research Database (Denmark)

    Nicolajsen, Hanne Westh; Ahola, Titta; Fleury, Alexandre

    In this deliverable usability and user experience are defined in relation to MAGNET Beyond technologies, and it is described how the main MAGNET Beyond concepts can be evaluated through the involvement of users. The concepts include the new "Activity based communication approach" for interacting...... with the MAGNET Beyond system, as well as the core concepts: Personal Network, Personal Network-Federation, Service Discovery, User Profile Management, Personal Network Management, Privacy and Security and Context Awareness. The overall plans for the final usability evaluation are documented based on the present...

  6. The theoretical ultimate magnetoelectric coefficients of magnetoelectric composites by optimization design

    International Nuclear Information System (INIS)

    Wang, H.-L.; Liu, B.

    2014-01-01

    This paper investigates what is the largest magnetoelectric (ME) coefficient of ME composites, and how to realize it. From the standpoint of energy conservation, a theoretical analysis is carried out on an imaginary lever structure consisting of a magnetostrictive phase, a piezoelectric phase, and a rigid lever. This structure is a generalization of various composite layouts for optimization on ME effect. The predicted theoretical ultimate ME coefficient plays a similar role as the efficiency of ideal heat engine in thermodynamics, and is used to evaluate the existing typical ME layouts, such as the parallel sandwiched layout and the serial layout. These two typical layouts exhibit ME coefficient much lower than the theoretical largest values, because in the general analysis the stress amplification ratio and the volume ratio can be optimized independently and freely, but in typical layouts they are dependent or fixed. To overcome this shortcoming and achieve the theoretical largest ME coefficient, a new design is presented. In addition, it is found that the most commonly used electric field ME coefficient can be designed to be infinitely large. We doubt the validity of this coefficient as a reasonable ME effect index and consider three more ME coefficients, namely the electric charge ME coefficient, the voltage ME coefficient, and the static electric energy ME coefficient. We note that the theoretical ultimate value of the static electric energy ME coefficient is finite and might be a more proper measure of ME effect

  7. Experimental study on ultimate strength and strain behavior of concrete under biaxial compressive stresses

    International Nuclear Information System (INIS)

    Onuma, Hiroshi; Aoyagi, Yukio

    1976-01-01

    The purpose of this investigation was to study the ultimate strength failure mode and deformation behavior of concrete under short-term biaxial compressive stresses, as an aid to design and analyze the concrete structures subjected to multiaxial compression such as prestressed or reinforced concrete vessel structures. The experimental work on biaxial compression was carried out on the specimens of three mix proportions and different ages with 10cm x 10cm x 10cm cubic shape in a room controlled at 20 0 C. The results are summarized as follows. (1) To minimize the surface friction between specimens and loading platens, the pads of teflon sheets coated with silicone grease were used. The coefficient of friction was measured and was 3 percent on the average. (2) The test data showed that the strength of the concrete subjected to biaxial compression increased as compared to uniaxial compressive strength, and that the biaxial strength increase was mainly dependent on the ratio of principal stresses, and it was hardly affected by mix proportions and ages. (3) The maximum increase of strength, which occurred at the stress ratio of approximately sigma 2 /sigma 1 = 0.6, was about 27 percent higher than the uniaxial strength of concrete. (4) The ultimate strength in case of biaxial compression could be approximated by the parabolic equation. (Kako, I.)

  8. Secondary Moments due to Prestressing with Different Bond at the Ultimate Limit State

    Directory of Open Access Journals (Sweden)

    Halvoník Jaroslav

    2018-03-01

    Full Text Available Secondary effects of prestressing develop in statically indeterminate structures (e.g., continuous beams due to the restraint of deformations imposed by hyperstatic restraints. These effects may significantly influence internal forces and stresses in prestressed structures. Secondary effects are influenced by the redundancy of a structural system, which raises the question of whether they will remain constant after a change in the structural system, e.g., due to the development of plastic hinge(s in a critical cross-section(s or after the development of a kinematic mechanism, or if they will disappear when the structure changes into a sequence of simply supported beams. The paper deals with an investigation of the behavior of continuous post-tensioned beams subjected to an ultimate load with significant secondary effects from prestressing. A total of 6 two-span beams prestressed by tendons with different bonds were tested in a laboratory with a load that changed their structural system into a kinematic mechanism. The internal forces and secondary effects of the prestressing were controlled through measurements of the reactions in all the supports. The results revealed that the secondary effects remained as a permanent part of the action on the experimental beams, even after the development of the kinematic mechanism. The results obtained confirmed that secondary effects should be included in all combinations of actions for verifications of ultimate limit states (ULS.

  9. Secondary Moments due to Prestressing with Different Bond at the Ultimate Limit State

    Science.gov (United States)

    Halvoník, Jaroslav; Pažma, Peter; Vida, Radoslav

    2018-03-01

    Secondary effects of prestressing develop in statically indeterminate structures (e.g., continuous beams) due to the restraint of deformations imposed by hyperstatic restraints. These effects may significantly influence internal forces and stresses in prestressed structures. Secondary effects are influenced by the redundancy of a structural system, which raises the question of whether they will remain constant after a change in the structural system, e.g., due to the development of plastic hinge(s) in a critical cross-section(s) or after the development of a kinematic mechanism, or if they will disappear when the structure changes into a sequence of simply supported beams. The paper deals with an investigation of the behavior of continuous post-tensioned beams subjected to an ultimate load with significant secondary effects from prestressing. A total of 6 two-span beams prestressed by tendons with different bonds were tested in a laboratory with a load that changed their structural system into a kinematic mechanism. The internal forces and secondary effects of the prestressing were controlled through measurements of the reactions in all the supports. The results revealed that the secondary effects remained as a permanent part of the action on the experimental beams, even after the development of the kinematic mechanism. The results obtained confirmed that secondary effects should be included in all combinations of actions for verifications of ultimate limit states (ULS).

  10. Bootstrap calculation of ultimate strength temperature maxima for neutron irradiated ferritic/martensitic steels

    Science.gov (United States)

    Obraztsov, S. M.; Konobeev, Yu. V.; Birzhevoy, G. A.; Rachkov, V. I.

    2006-12-01

    The dependence of mechanical properties of ferritic/martensitic (F/M) steels on irradiation temperature is of interest because these steels are used as structural materials for fast, fusion reactors and accelerator driven systems. Experimental data demonstrating temperature peaks in physical and mechanical properties of neutron irradiated pure iron, nickel, vanadium, and austenitic stainless steels are available in the literature. A lack of such an information for F/M steels forces one to apply a computational mathematical-statistical modeling methods. The bootstrap procedure is one of such methods that allows us to obtain the necessary statistical characteristics using only a sample of limited size. In the present work this procedure is used for modeling the frequency distribution histograms of ultimate strength temperature peaks in pure iron and Russian F/M steels EP-450 and EP-823. Results of fitting the sums of Lorentz or Gauss functions to the calculated distributions are presented. It is concluded that there are two temperature (at 360 and 390 °C) peaks of the ultimate strength in EP-450 steel and single peak at 390 °C in EP-823.

  11. Application of risk-informed design methods to select the PSACS ultimate heat sink

    International Nuclear Information System (INIS)

    Elliott, Michael A.; Apostolakis, George E.

    2009-01-01

    In the early phases of advanced system design, information is scarce. The technologies, components and processes to be used have not been specified adequately or are not well understood and uncertainties are very large. Yet, it is during these early phases that design teams and other stakeholders are required to make critical decisions to guide the development of the system. To aid in this decision making, a formal process is proposed based on the Analytic-Deliberative Decision-Making Process (ADP) that allows stakeholders to synthesize rationally their knowledge and experience and facilitate learning and sharing of best practices. The ADP identifies and prioritizes attributes relevant to a decision problem and supports the formulation of metrics to measure the performance of different design options. This paper reports on an application of the ADP to the selection of an ultimate heat sink for the Flexible Conversion Ratio (FCR) reactor's Passive Secondary Auxiliary Cooling System (PSACS). Two ultimate heat sink options are identified and evaluated, air and water.

  12. Plasticity and constraints on social evolution in African mole-rats: ultimate and proximate factors.

    Science.gov (United States)

    Faulkes, Chris G; Bennett, Nigel C

    2013-05-19

    Here, we review comparative studies of African mole-rats (family Bathyergidae) to explain how constraints acting at the ultimate (environmental) and proximate (organismal) levels have led to convergent gains and losses of sociality within this extensive adaptive radiation of subterranean rodents endemic to sub-Saharan Africa. At the ultimate level, living in environments that range from mesic through to arid has led to both variation and flexibility in social organization among species, culminating in the pinnacle of social evolution in the eusocial naked and Damaraland mole-rats (Heterocephalus glaber and Fukomys damarensis). The common mole-rat (Cryptomys hottentotus) provides a model example of how plasticity in social traits exists within a single species inhabiting areas with different ecological constraint. At the proximate level, reproductive strategies and cooperative breeding may be constrained by the correlated evolution of a suite of traits including physiological suppression of reproduction, the development of physiological and morphological castes, and the mode of ovulatory control and seasonality in breeding. Furthermore, recent neurobiological advances indicate that differential patterns of neurotransmitter expression within the forebrain may underpin (and limit) either a solitary or group living/cooperative lifestyle not only in mole-rats, but also more widely among disparate mammalian taxa.

  13. Evaluation of the ultimate pressure capacity of rectangular HVAC ducts for nuclear pwoer plants

    International Nuclear Information System (INIS)

    Wedellsborg, B.W.

    1984-01-01

    Typical Category I HVAC ducts in a nuclear plant must be designed for loads and load combinations including positive and negative pressure loads which are generated due to the normal operation and postulated accident conditions. These pressure loads most often govern the design of the HVAC ducts. Structural design criteria are presently based on the AISI Code which limits the duct panel width-to-thickness ratio to a maximum of 500 and the maximum height-to-thickness ratio to 200, unless it can be shown by structural tests that larger ratios can be used. Test Programs performed on rectangular HVAC ducts subjected to vacumm loads have substantiated the use of ducts having panel width to thickness ratios of up to 1600. The results of the test programs were subsequently incorporated into the design through a more rational analytical design method which was developed from and correlates well with the test results. The purpose of this paper is to present the analytical design method and its correlation with the test results. Simple formulae for the design of rectangular HVAC ducts are presented. Lower bound values of duct sheet, and stiffener ultimate loads are derived, and correlated with recent test results. Analytically predicted ultimate pressures are also compared with other available duct test data

  14. ULtiMATE system for rapid assembly of customized TAL effectors.

    Directory of Open Access Journals (Sweden)

    Junjiao Yang

    Full Text Available Engineered TAL-effector nucleases (TALENs and TALE-based constructs have become powerful tools for eukaryotic genome editing. Although many methods have been reported, it remains a challenge for the assembly of designer-based TALE repeats in a fast, precise and cost-effective manner. We present an ULtiMATE (USER-based Ligation Mediated Assembly of TAL Effector system for speedy and accurate assembly of customized TALE constructs. This method takes advantage of uracil-specific excision reagent (USER to create multiple distinct sticky ends between any neighboring DNA fragments for specific ligation. With pre-assembled templates, multiple TALE DNA-binding domains could be efficiently assembled in order within hours with minimal manual operation. This system has been demonstrated to produce both functional TALENs for effective gene knockout and TALE-mediated gene-specific transcription activation (TALE-TA. The feature of both ease-of-operation and high efficiency of ULtiMATE system makes it not only an ideal method for biologic labs, but also an approach well suited for large-scale assembly of TALENs and any other TALE-based constructions.

  15. Ultimate shearing strength of aseismatic walls with many small holes for reactor buildings

    International Nuclear Information System (INIS)

    Yoshizaki, Seiji; Ezaki, Tetsuro; Korenaga, Takeyoshi; Sotomura, Kentaro.

    1984-01-01

    The aseismatic walls for reactor buildings have complicated forms, and are characterized by large wall thickness and high reinforcement ratio as compared with ordinary aseismatic walls. The forms are mainly box, cylinder or irregular polygonal prism and their combination. The design of the walls with many small holes has been performed on the basis of the reinforced concrete structure calculation standard of the Architectural Institute of Japan, following the case with large opening. When there are many small holes, the arrangement of reinforcement for the openings becomes complex, and the construction is difficult. It is necessary to rationalize the design and to simplify the reinforcement work. Under the background like this, the experiment to examine the shearing property in bending of the aseismatic walls with many small holes for reactor buildings was carried out, and horizontal loading test was performed on 43 specimens. The method of calculating the ultimate shearing strength of a wall without opening was proposed, and the method of applying it to a wall with many small holes is shown. The experimental method and the results, the examination of the experimental results, and the ultimate shearing strength of the aseismatic walls are reported. (Kako, I.)

  16. Ultimate strength performance of tankers associated with industry corrosion addition practices

    Directory of Open Access Journals (Sweden)

    Kim Do Kyun

    2014-09-01

    Full Text Available In the ship and offshore structure design, age-related problems such as corrosion damage, local denting, and fatigue damage are important factors to be considered in building a reliable structure as they have a significant influence on the residual structural capacity. In shipping, corrosion addition methods are widely adopted in structural design to prevent structural capacity degradation. The present study focuses on the historical trend of corrosion addition rules for ship structural design and investigates their effects on the ultimate strength performance such as hull girder and stiffened panel of double hull oil tankers. Three types of rules based on corrosion addition models, namely historic corrosion rules (pre-CSR, Common Structural Rules (CSR, and harmonised Common Structural Rules (CSRH are considered and compared with two other corrosion models namely UGS model, suggested by the Union of Greek Shipowners (UGS, and Time-Dependent Corrosion Wastage Model (TDCWM. To identify the general trend in the effects of corrosion damage on the ultimate longitudinal strength performance, the corrosion addition rules are applied to four representative sizes of double hull oil tankers namely Panamax, Aframax, Suezmax, and VLCC. The results are helpful in understanding the trend of corrosion additions for tanker structures

  17. Ultimate strength performance of tankers associated with industry corrosion addition practices

    Directory of Open Access Journals (Sweden)

    Do Kyun Kim

    2014-09-01

    Full Text Available In the ship and offshore structure design, age-related problems such as corrosion damage, local denting, and fatigue damage are important factors to be considered in building a reliable structure as they have a significant influence on the residual structural capacity. In shipping, corrosion addition methods are widely adopted in structural design to prevent structural capacity degradation. The present study focuses on the historical trend of corrosion addition rules for ship structural design and investigates their effects on the ultimate strength performance such as hull girder and stiffened panel of double hull oil tankers. Three types of rules based on corrosion addition models, namely historic corrosion rules (pre-CSR, Common Structural Rules (CSR, and harmonised Common Structural Rules (CSRH are considered and compared with two other corrosion models namely UGS model, suggested by the Union of Greek Shipowners (UGS, and Time-Dependent Corrosion Wastage Model (TDCWM. To identify the general trend in the effects of corrosion damage on the ultimate longitudinal strength performance, the corrosion addition rules are applied to four representative sizes of double hull oil tankers namely Panamax, Aframax, Suezmax, and VLCC. The results are helpful in understanding the trend of corrosion additions for tanker structures.

  18. Expressiveness and definability in circumscription

    Directory of Open Access Journals (Sweden)

    Francicleber Martins Ferreira

    2011-06-01

    Full Text Available We investigate expressiveness and definability issues with respect to minimal models, particularly in the scope of Circumscription. First, we give a proof of the failure of the Löwenheim-Skolem Theorem for Circumscription. Then we show that, if the class of P; Z-minimal models of a first-order sentence is Δ-elementary, then it is elementary. That is, whenever the circumscription of a first-order sentence is equivalent to a first-order theory, then it is equivalent to a finitely axiomatizable one. This means that classes of models of circumscribed theories are either elementary or not Δ-elementary. Finally, using the previous result, we prove that, whenever a relation Pi is defined in the class of P; Z-minimal models of a first-order sentence Φ and whenever such class of P; Z-minimal models is Δ-elementary, then there is an explicit definition ψ for Pi such that the class of P; Z-minimal models of Φ is the class of models of Φ ∧ ψ. In order words, the circumscription of P in Φ with Z varied can be replaced by Φ plus this explicit definition ψ for Pi.

  19. Defining Quality in Undergraduate Education

    Directory of Open Access Journals (Sweden)

    Alison W. Bowers

    2018-01-01

    Full Text Available Objectives: This research brief explores the literature addressing quality in undergraduate education to identify what previous research has said about quality and to offer future directions for research on quality in undergraduate education. Method: We conducted a scoping review to provide a broad overview of existing research. Using targeted search terms in academic databases, we identified and reviewed relevant academic literature to develop emergent themes and implications for future research. Results: The exploratory review of the literature revealed a range of thoughtful discussions and empirical studies attempting to define quality in undergraduate education. Many publications highlighted the importance of including different stakeholder perspectives and presented some of the varying perceptions of quality among different stakeholders. Conclusions: While a number of researchers have explored and written about how to define quality in undergraduate education, there is not a general consensus regarding a definition of quality in undergraduate education. Past research offers a range of insights, models, and data to inform future research. Implication for Theory and/or Practice: We provide four recommendations for future research to contribute to a high quality undergraduate educational experience. We suggest more comprehensive systematic reviews of the literature as a next step.

  20. Optimum hub height of a wind turbine for maximizing annual net profit

    International Nuclear Information System (INIS)

    Lee, Jaehwan; Kim, Dong Rip; Lee, Kwan-Soo

    2015-01-01

    Highlights: • Annual Net Profit was proposed to optimize the hub height of a wind turbine. • Procedures of the hub height optimization method were introduced. • Effect of local wind speed characteristics on optimum hub height was illustrated. • Effect of rated power on optimum hub height was negligible in the range 0.75–3 MW. • Rated speed and cut-out speed had great effects on optimum hub height. - Abstract: The optimization method of the hub height, which can ensure the economic feasibility of the wind turbine, is proposed in this study. Annual Net Profit is suggested as an objective function and the optimization procedure is developed. The effects of local wind speed and wind turbine power characteristics on the optimum hub height are investigated. The optimum hub height decreased as the mean wind speed and wind shear exponent increased. Rated power had little effect on optimum hub height; it follows that the economies of scale are negligible in the rated power range of 0.75–3 MW. Among the wind turbine power characteristics, rated speed and cut-out speed most strongly affected the optimum hub height

  1. Long-term experience in salt mining and experience in salt mine decommissioning - a chance for ultimate storage?

    International Nuclear Information System (INIS)

    Sitz, P.; Rauche, H.

    2003-01-01

    The author discusses similarities between salt mining and ultimate storage and the possibility of using abandoned salt mines as ultimate storage site. He states that with all the numeric prediction tools now available, expert knowledge of mining engineers is still indispensable [de

  2. Development of Non-Optimum Factors for Launch Vehicle Propellant Tank Bulkhead Weight Estimation

    Science.gov (United States)

    Wu, K. Chauncey; Wallace, Matthew L.; Cerro, Jeffrey A.

    2012-01-01

    Non-optimum factors are used during aerospace conceptual and preliminary design to account for the increased weights of as-built structures due to future manufacturing and design details. Use of higher-fidelity non-optimum factors in these early stages of vehicle design can result in more accurate predictions of a concept s actual weights and performance. To help achieve this objective, non-optimum factors are calculated for the aluminum-alloy gores that compose the ogive and ellipsoidal bulkheads of the Space Shuttle Super-Lightweight Tank propellant tanks. Minimum values for actual gore skin thicknesses and weld land dimensions are extracted from selected production drawings, and are used to predict reference gore weights. These actual skin thicknesses are also compared to skin thicknesses predicted using classical structural mechanics and tank proof-test pressures. Both coarse and refined weights models are developed for the gores. The coarse model is based on the proof pressure-sized skin thicknesses, and the refined model uses the actual gore skin thicknesses and design detail dimensions. To determine the gore non-optimum factors, these reference weights are then compared to flight hardware weights reported in a mass properties database. When manufacturing tolerance weight estimates are taken into account, the gore non-optimum factors computed using the coarse weights model range from 1.28 to 2.76, with an average non-optimum factor of 1.90. Application of the refined weights model yields non-optimum factors between 1.00 and 1.50, with an average non-optimum factor of 1.14. To demonstrate their use, these calculated non-optimum factors are used to predict heavier, more realistic gore weights for a proposed heavy-lift launch vehicle s propellant tank bulkheads. These results indicate that relatively simple models can be developed to better estimate the actual weights of large structures for future launch vehicles.

  3. Comparative analysis of diffused solar radiation models for optimum tilt angle determination for Indian locations

    International Nuclear Information System (INIS)

    Yadav, P.; Chandel, S.S.

    2014-01-01

    Tilt angle and orientation greatly are influenced on the performance of the solar photo voltaic panels. The tilt angle of solar photovoltaic panels is one of the important parameters for the optimum sizing of solar photovoltaic systems. This paper analyses six different isotropic and anisotropic diffused solar radiation models for optimum tilt angle determination. The predicted optimum tilt angles are compared with the experimentally measured values for summer season under outdoor conditions. The Liu and Jordan model is found to exhibit t lowest error as compared to other models for the location. (author)

  4. Defining the "normal" postejaculate urinalysis.

    Science.gov (United States)

    Mehta, Akanksha; Jarow, Jonathan P; Maples, Pat; Sigman, Mark

    2012-01-01

    Although sperm have been shown to be present in the postejaculate urinalysis (PEU) of both fertile and infertile men, the number of sperm present in the PEU of the general population has never been well defined. The objective of this study was to describe the semen and PEU findings in both the general and infertile population, in order to develop a better appreciation for "normal." Infertile men (n = 77) and control subjects (n = 71) were prospectively recruited. Exclusion criteria included azoospermia and medications known to affect ejaculation. All men underwent a history, physical examination, semen analysis, and PEU. The urine was split into 2 containers: PEU1, the initial voided urine, and PEU2, the remaining voided urine. Parametric statistical methods were applied for data analysis to compare sperm concentrations in each sample of semen and urine between the 2 groups of men. Controls had higher average semen volume (3.3 ± 1.6 vs 2.0 ± 1.4 mL, P sperm concentrations (112 million vs 56.2 million, P = .011), compared with infertile men. The presence of sperm in urine was common in both groups, but more prevalent among infertile men (98.7% vs 88.7%, P = .012), in whom it comprised a greater proportion of the total sperm count (46% vs 24%, P = .022). The majority of sperm present in PEU were seen in PEU1 of both controls (69%) and infertile men (88%). An association was noted between severe oligospermia (sperm counts in PEU (sperm in the urine compared with control, there is a large degree of overlap between the 2 populations, making it difficult to identify a specific threshold to define a positive test. Interpretation of a PEU should be directed by whether the number of sperm in the urine could affect subsequent management.

  5. Miniature EVA Software Defined Radio

    Science.gov (United States)

    Pozhidaev, Aleksey

    2012-01-01

    As NASA embarks upon developing the Next-Generation Extra Vehicular Activity (EVA) Radio for deep space exploration, the demands on EVA battery life will substantially increase. The number of modes and frequency bands required will continue to grow in order to enable efficient and complex multi-mode operations including communications, navigation, and tracking applications. Whether conducting astronaut excursions, communicating to soldiers, or first responders responding to emergency hazards, NASA has developed an innovative, affordable, miniaturized, power-efficient software defined radio that offers unprecedented power-efficient flexibility. This lightweight, programmable, S-band, multi-service, frequency- agile EVA software defined radio (SDR) supports data, telemetry, voice, and both standard and high-definition video. Features include a modular design, an easily scalable architecture, and the EVA SDR allows for both stationary and mobile battery powered handheld operations. Currently, the radio is equipped with an S-band RF section. However, its scalable architecture can accommodate multiple RF sections simultaneously to cover multiple frequency bands. The EVA SDR also supports multiple network protocols. It currently implements a Hybrid Mesh Network based on the 802.11s open standard protocol. The radio targets RF channel data rates up to 20 Mbps and can be equipped with a real-time operating system (RTOS) that can be switched off for power-aware applications. The EVA SDR's modular design permits implementation of the same hardware at all Network Nodes concept. This approach assures the portability of the same software into any radio in the system. It also brings several benefits to the entire system including reducing system maintenance, system complexity, and development cost.

  6. What is the optimum minimum segment size used in step and shoot IMRT for prostate cancer?

    International Nuclear Information System (INIS)

    Takahashi, Yutaka; Sumida, Iori; Koizumi, Masahiko

    2010-01-01

    Although the use of small segments in step and shoot intensity modulated radiation therapy (IMRT) provides better dose distribution, extremely small segments decrease treatment accuracy. The purpose of this study was to determine the optimum minimum segment size (MSS) in two-step optimization in prostate step and shoot IMRT with regard to both planning quality and dosimetric accuracy. The XiO treatment planning system and Oncor Impression Plus were used. Results showed that the difference in homogeneity index (HI), defined as the ratio of maximum to minimum doses for planning target volume, between the MSS 1.0 cm and 1.5 cm plans, and 2.0 cm plans, was 0.1%, and 9.6%, respectively. With regard to V107 of planning target volume (PTV), the volume receiving 107% of the prescribed dose of the PTV, the difference between MSS 1.0 cm and 1.5 cm was 2%. However, the value of the MSS 2.0 cm or greater plans was more than 2.5-fold that of the MSS 1.0 cm plan. With regard to maximum rectal dose, a significant difference was seen between the MSS 1.5 cm and 2.0 cm plans, whereas no significant difference was seen between the MSS 1.0 cm and 1.5 cm plans. Composite plan verification revealed a greater than 5% dose difference between planned and measured dose in many regions with the MSS 1.0 cm plan, but in only limited regions in the MSS 1.5 cm plan. Our data suggest that the MSS should be determined with regard to both planning quality and dosimetric accuracy. (author)

  7. The neuroanatomist's dream, the problems and solutions, and the ultimate aim

    OpenAIRE

    Felipe, Javier de

    2008-01-01

    The principal goal in neuroanatomy is to define the detailed structural design of the nervous system. This challenge is one of the first steps towards understanding how neural circuits contribute to the functional organization of the nervous system, both in health and disease. The main difficulties involve unraveling the extraordinary complexity of the nervous system and to define how information flows through this finely organized synaptic network. Over the years, neuroanatomy has evolved co...

  8. Health care quality, access, cost, workforce, and surgical education: the ultimate perfect storm.

    Science.gov (United States)

    Schwartz, Marshall Z

    2012-01-01

    The discussions on health care reform over the past two years have focused on cost containment while trying to maintain quality of care. Focusing on just cost and quality unfortunately does not address other very important factors that impact on our health care delivery system. Availability of a well-trained workforce, maintaining the sophisticated medical/surgical education system, and ultimately access to quality care by the public are critical to maintaining and enhancing our health care delivery system. Unfortunately, all five of these components are under at risk. Thus, we have evolving the ultimate perfect storm affecting our health care delivery system. Although not ideal and given the uniqueness of our population and their expectations, our current delivery system is excellent compared to other countries. However, the cost of our current system is rising at an alarming rate. Currently, health care consumes 17% of our gross domestic product. If our system is not revised this will continue to rise and by 2025 it will consume 48%. The dilemma, given the current state of our overall economy and rising debt, is how to address this major problem. Unfortunately, the Affordable Care Act, which is now law, does not address most of the issues and the cost was initially grossly under estimated. Furthermore, the law does not address the issues of workforce, maintaining our medical education system or ultimately, access. A major revision of our system will be necessary to truly create a system that protects and enhances all five of the components of our health care delivery system. To effectively accomplish this will require addressing those issues that lead to wasteful spending and diversion of our health care dollars to profit instead of care. Improved and efficient delivery systems that reduce complications, reduction of duplication of tertiary and quaternary programs or services within the same markets (i.e. regionalization of care), health insurance reform, and

  9. Aging characteristics of containment building and sensitivity on ultimate pressure capacity

    International Nuclear Information System (INIS)

    Seo, Jeong Moon; Choun, Young Sun; Choi, In Kil; Ha, Jae Joo

    1998-03-01

    For the reliable safety assessment of the containment building, structural and material conditions can be investigated in detail and pertinent assessment technologies have to be established. Also, an understanding on the aging-related degradations for the construction materials is required to predict long-term structural safety of the containment building. For the development of reliable aging prediction models, an extensive data base system related to aging properties of the containment building has to be prepared. The objectives of this research are to develop aging models representing long-term degradation of materials and a structural performance assessment program for containment building considering aging-related degradation. According to the results of sensitivity analysis, as the mechanical properties of the constituent materials degrade, the ultimate pressure capacity of containment building may decrease and severe damage may occur around the mid-level of the containment wall. (author). 28 refs., 11 tabs., 36 figs

  10. Ultimate Limit State Design Of Sheet Pile Walls By Finite Elements And Nonlinear Programming

    DEFF Research Database (Denmark)

    Krabbenhøft, Kristian; Damkilde, Lars; Krabbenhøft, Sven

    2002-01-01

    Limit analysis has been used for decades in civil and mechanical engineering practice as a means of analyzing structures of materials which with reasonable accuracy can be described as being rigid-perfectly plastic. Such materials include steel, concrete and soils. Traditionally, most attention has...... been given to the problem which consists of determining the ultimate magnitude of a given set of loads acting on a structure with a given geometry. This problem is relevant when determining e.g. the necessary extrusion pressure in metal forming problems, when evaluating the bearing capacity...... is the load intensity. In the paper we consider the latter of these problems with particular reference to the design of sheet pile walls....

  11. Patient dose rate: An ultimate limit for spatial and density resolution of scanning systems

    International Nuclear Information System (INIS)

    Kowalski, G.; Wagner, W.

    1979-01-01

    In X-ray scanning systems, picture quality of the reconstructed slices is limited to a maximum spatial as well as density resolution by the applied radiation dose. Density resolution can be improved in proportion to the root of the patient dose, whereas a doubled spatial resolving power requires an eight times higher patient dose, assuming a fixed slice thickness. Only a careful trade-off between the applied patient dose, density resolution and spatial resolution yields a maximal diagnostic value for the physician. Specifications of a scanning system have to take into account these ultimate restrictions, so that picture quality really is limited by the patient's dose rather than by technical constraints. In addition a method is given by which the applied dose can be reduced by focusing the main intensity onto the region of interest, in case that region is known a priori. (orig.) [de

  12. Methodological Challenges of Identifying Ultimate Land Use Changes Caused by Biofuel Production

    DEFF Research Database (Denmark)

    Wenzel, Henrik; Kløverpris, Jesper; Nielsen, Per Henning

    2007-01-01

    that is only poorly dealt with by LCA methods. Even though the use of land, or change of land cover and its eco-systems, is acknowledged to be a very important impact of human activities, a methodology for assessing this impact category has not yet  been properly developed within LCA. Some LCA scientists have...... looked into methods for assessing the impacts of given changes of land use, i.e. the impact assessment component of the LCA, but very few have looked into how to actually do the inventory modelling, i.e. how to identify which land is ultimately affected by the decision and system under study. State...... in the systems being studied. The aims of this paper is to analyse the mechanisms influencing the long-term land use consequences of changes in crop demand and propose a methodological framework for identifying these consequences within a global scope. The outset of the paper is the principles of consequential...

  13. SoundScapes - Beyond Interaction... in search of the ultimate human-centred interface

    DEFF Research Database (Denmark)

    Brooks, Tony

    2006-01-01

    that can also benefit communication. To achieve this a new generation of intuitive natural interfaces will be required and SoundScapes (see below) is a step toward this goal to discover the ultimate interface for matching the human experience to technology. Emergent hypothesis that have developed...... as a result of the SoundScapes research will be discussed. Introduction to SoundScapes SoundScapes is a contemporary art concept that has become widely known as an interdisciplinary platform for knowledge exchange, innovative product creation of creative and scientific work that uses non-invasive sensor...... Resonance. The multimedia content is adaptable so that the environment is tailored for each participant according to a user profile. This full body movement or the smallest of gesture results in human data input to SoundScapes. The same technology that enables this empowerment is used for performance art...

  14. An experimental investigation on the ultimate strength of epoxy repaired braced partial infilled RC frames

    Science.gov (United States)

    Dubey, Shailendra Kumar Damodar; Kute, Sunil

    2014-09-01

    Due to earthquake, buildings are damaged partially or completely. Particularly structures with soft storey are mostly affected. In general, such damaged structures are repaired and reused. In this regard, an experimental investigation was planned and conducted on models of single-bay, single-storey of partial concrete infilled reinforced concrete (RC) frames up to collapse with corner, central and diagonal steel bracings. Such collapsed frames were repaired with epoxy resin and retested. The initiative was to identify the behaviour, extent of restored ultimate strength and deflection of epoxy-retrofitted frames in comparison to the braced RC frames. The performance of such frames has been considered only for lateral loads. In comparison to bare RC frames, epoxy repaired partial infilled frames have significant increase in the lateral load capacity. Central bracing is more effective than corner and diagonal bracing. For the same load, epoxy repaired frames have comparable deflection than similar braced frames.

  15. Silicon coupled-ring resonator structures for slow light applications: potential, impairments and ultimate limits

    International Nuclear Information System (INIS)

    Canciamilla, A; Torregiani, M; Ferrari, C; Morichetti, F; Melloni, A; De La Rue, R M; Samarelli, A; Sorel, M

    2010-01-01

    Coupled-ring resonator-based slow light structures are reported and discussed. By combining the advantages of high index contrast silicon-on-insulator technology with an efficient thermo-optical activation, they provide an on-chip solution with a bandwidth of up to 100 GHz and a slowdown factor of up to 16, as well as a continuous reconfiguration scheme and a fine tunability. The performance of these devices is investigated in detail for both static and dynamic operation, in order to evaluate their potential in optical signal processing applications at high bit rate. The main impairments imposed by fabrication imperfections are also discussed in relation to the slowdown factor. In particular, the analysis of the impact of backscatter, disorder and two-photon absorption on the device transfer function reveals the ultimate limits of these structures and provides valuable design rules for their optimization

  16. Process for extracting residual heat and device for the ultimate absorption of heat for nuclear reactors

    International Nuclear Information System (INIS)

    Bernard, Lawrence Jr.

    1980-01-01

    This invention concerns a 'heat sink' or device for the ultimate absorption of heat for electric power stations using the most widespread thermal neutron nuclear reactors, namely 'light water' reactors such as boiling or pressurized water reactors. The residual heat given off by these reactors can be safely extracted with this method by using dry cooling. However, the invention does not concern the problems arising from the cooling of the steam used for actuating the steam turbine nor the cooling of the steam exhausted by the turbine or coming from it, but it does concern the 'safety' part of the nuclear power station in which the residual heat discharged in the reactor is controlled and dissipated [fr

  17. Design proposal for ultimate shear strength of tapered steel plate girders

    Directory of Open Access Journals (Sweden)

    A. Bedynek

    2017-03-01

    Full Text Available Numerous experimental and numerical studies on prismatic plate girders subjected to shear can be found in the literature. However, the real structures are frequently designed as non-uniform structural elements. The main objective of the research is the development of a new proposal for the calculation of the ultimate shear resistance of tapered steel plate girders taking into account the specific behaviour of such members. A new mechanical model is presented in the paper and it is used to show the differences between the behaviour of uniform and tapered web panels subjected to shear. EN 1993-1-5 design specifications for the determination of the shear strength for rectangular plates are improved in order to assess the shear strength of tapered elements. Numerical studies carried out on tapered steel plate girders subjected to shear lead to confirm the suitability of the mechanical model and the proposed design expression.

  18. Determination of the ultimate load in concrete slabs by the yield line finite element method

    International Nuclear Information System (INIS)

    Vaz, L.E.; Feijo, B.; Martha, L.F.R.; Lopes, M.M.

    1984-01-01

    A method for calculating the ultimate load in reinforced concrete slabs is proposed. The method follows the finite element aproach representating the continuum slab as an assembly of rigid triangular plates connected along their sides through yield line elements. This approach leads to the definition of the displacement configuration of the plate only as a function of the transversal displacement at the nodes of the mesh (1 DOF per node) reducing significantly the number of DOF's in relation to the conventional formulation by means of the finite element method (minimum of 3 DOF per node). Nonlinear behaviour of the reinforced concrete section is considered in the definition of the moment rotation curve of the yield lines. The effect of the in plane forces acting in the middle surface of the plate is also taken into account. The validity of the model is verified comparing the numerical solutions with the results of the classical yield line theory. (Author) [pt

  19. Fuzzy stochastic analysis of serviceability and ultimate limit states of two-span pedestrian steel bridge

    Science.gov (United States)

    Kala, Zdeněk; Sandovič, GiedrÄ--

    2012-09-01

    The paper deals with non-linear analysis of ultimate and serviceability limit states of two-span pedestrian steel bridge. The effects of random material and geometrical characteristics on limit states are analyzed. The Monte Carlo method was applied to stochastic analysis. For the serviceability limit state, also influence of fuzzy uncertainty of the limit deflection value on random characteristics of load capacity of variable action was studied. The results prove that, for the type of structure studied, the serviceability limit state is decisive from the point of view of design. The present paper opens a discussion on the use of stochastic analysis to verify the limit deflections given in the standards EUROCODES.

  20. Review of ultimate pressure capacity test of containment structure and scale model design techniques

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Jeong Moon; Choi, In Kil [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-03-01

    This study was performed to obtain the basic knowledge of the scaled model test through the review of experimental studies conducted in foreign countries. The results of this study will be used for the wall segment test planed in next year. It was concluded from the previous studies that the larger the model, the greater the trust of the community in the obtained results. It is recommended that a scale model 1/4 - 1/6 be suitable considering the characteristics of concrete, reinforcement, liner and tendon. Such a large scale model test require large amounts of time and budget. Because of these reasons, it is concluded that the containment wall segment test with analytical studies is efficient for the verification of the ultimate pressure capacity of the containment structures. 57 refs., 46 figs., 11 tabs. (Author)