WorldWideScience

Sample records for udimet 700

  1. Mechanical properties of modified low cobalt powder metallurgy Udimet 700 type alloys

    Science.gov (United States)

    Harf, Fredric H.

    1989-01-01

    Eight superalloys derived from Udimet 700 were prepared by powder metallurgy, hot isostatically pressed, heat treated and their tensile and creep rupture properties determined. Several of these alloys displayed properties superior to those of Udimet 700 similarly prepared, in one case exceeding the creep rupture life tenfold. Filter clogging by extracted gamma prime, its measurement and significance are discussed in an appendix.

  2. Development of a Sinter/HIP process for the superalloy Udimet 700 with investigations of the influence of the sinteratmosphere

    International Nuclear Information System (INIS)

    Wenning, L.

    1991-03-01

    The oxidation free treatment of reactive metalpowders like the nickel base alloy Udimet 700 demands sufficient oxygen free sinteratmospheres in nowadays sinter-HIP plants are not reachable. The reported work deals with the development of a sinter-HIP process which enables a sufficient low partial pressure of oxygen by scavenging the Udimet 700 powder packings with argon during vacuum sintering. By this the sinter hindering oxidation is avoided. Intensive investigations of the sinteratmosphere with a mass spectrometer and a zirconium oxide probe verify the reduction of the oxygen content of the residual gas atmosphere reached with different processes. In a second part the applicability of the scavenging gas process during the capsule free sinter-HIP treatment of metall injection moulded (MIM) samples is shown. (orig.) [de

  3. The substitution of nickel for cobalt in hot isostatically pressed powder metallurgy UDIMET 700 alloys

    Science.gov (United States)

    Harf, F. H.

    1985-01-01

    Nickel was substituted in various proportions for cobalt in a series of five hot-isostatically-pressed powder metallurgy alloys based on the UDIMET 700 composition. These alloys were given 5-step heat treatments appropriate for use in turbine engine disks. The resultant microstructures displayed three distinct sizes of gamma-prime particles in a gamma matrix. The higher cobalt-content alloys contained larger amounts of the finest gamma-prime particles, and had the lowest gamma-gamma-prime lattice mismatch. While all alloys had approximately the same tensile properties at 25 and 650 gamma C, the rupture lives at 650 and 760 C peaked in the alloys with cobalt contents between 12.7 and 4.3 pct. Minimum creep rates increased as cobalt contents were lowered, suggesting their correlation with the gamma-prime particle size distribution and the gamma-gamma-prime mismatch. It was also found that, on overaging at temperatures higher than suitable for turbine disk use, the high cobalt-content alloys were prone to sigma phase formation.

  4. Effect of the microstructure on the creep behavior of PM Udimet 720 superalloy--experiments and modeling

    International Nuclear Information System (INIS)

    Dubiez-Le Goff, Sophie; Couturier, Raphaeel; Guetaz, Laure; Burlet, Helene

    2004-01-01

    Powder metallurgy processed Udimet 720 is a high creep strength nickel-based superalloy considered for high temperature turbine disks for nuclear gas cooled reactors working under 700 deg. C. Both fine-grained and coarse-grained microstructures have been obtained by applying respectively a subsolvus or a supersolvus solution treatments, followed by ageing treatments. In both microstructures, the distribution of the strengthening γ' precipitates has been characterized by transmission electron microscopy (TEM). The creep curves of the coarse-grained microstructure show the three usual creep stages. On the contrary, the creep curves of the fine-grained microstructure show a transition directly from primary to apparent tertiary creep without any obvious steady state. According to TEM analyses, Orowan loops surround Udimet 720 CR γ' and U720 HS γ' at high stress whereas U720 HS γ' are sheared at low stress. To describe the behavior of the superalloy Udimet 720, a specific creep model is developed on the basis of McLean and Dyson models including physical damage parameters

  5. Effect of reduced cobalt contents on hot isostatically pressed powder metallurgy U-700 alloys

    Science.gov (United States)

    Harf, F. H.

    1982-01-01

    The effect of reducing the cobalt content of prealloyed powders of UDIMET 700 (U-700) alloys to 12.7, 8.6, 4.3, and 0% was examined. The powders were hot isostatically pressed into billets, which were given heat treatments appropriate for turbine disks, namely partial solutioning at temperatures below the gamma prime solvus and four step aging treatments. Chemical analyses, metallographic examinations, and X-ray diffraction measurements were performed on the materials. Minor effects on gamma prime content and on room temperature and 650 C tensile properties were observed. Creep rupture lives at 650 C reached a maximum at the 8.4% concentration, while at 760 C a maximum in life was reached at the 4.3% cobalt level. Minimum creep rates increased with decreasing cobalt content at both test temperatures. Extended exposures at 760 and 815 C resulted in decreased tensile strengths and rupture lives for all alloys. Evidence of sigma phase formation was also found.

  6. Notch size effects on high cycle fatigue limit stress of Udimet 720

    International Nuclear Information System (INIS)

    Ren Weiju; Nicholas, Theodore

    2003-01-01

    Notch size effects on the high cycle fatigue (HCF) limit stress of Ni-base superalloy Udimet 720 were investigated on cylindrical specimens with three notch sizes of the same stress concentration factor K t =2.74. The HCF limit stress corresponding to a life of 10 6 cycles was experimentally determined at a stress ratio of 0.1 and a frequency of 25 Hz at room temperature. The stresses were calculated using finite element analysis (FEA) and the specimens analyzed using scanning electron microscopy (SEM). Test results show that at the same K t value, notch size can slightly affect the HCF limit stress of U720 when notch root plasticity occurs. FEA and SEM results reveal that the notch size effects are influenced by a complicated combination of the stress and plastic strain fields at the notch tip, the nominal stress, and the effects of prior plastic deformation on fatigue crack initiation

  7. The effect of environment on the creep crack growth behavior of several structural alloys

    International Nuclear Information System (INIS)

    Sadananda, K.; Shahinian, P.

    1980-01-01

    The creep crack growth behaviors of alloy 718, Inconel X-750, Udimet 700 and cold-worked type 304 and annealed and cold-worked type 316 austenitic stainless steels were determined in vacuum at elevated temperatures and the results were compared with those previously obtained in air. Alloy 718 and Inconel X-750 were found to be significantly sensitive to air with crack growth rates one to two orders of magnitude greater than those in vacuum. Udimet 700 is less sensitive to the environment and it is more sensitive to small changes in microstructure than to the environment per se. The austenitic stainless steels are least sensitive of all. Since the environmental sensitivity varies significantly for different materials, the service environment should be considered in the selection of materials for high temperature components. (Auth.)

  8. Effects of High-Temperature Exposures on the Fatigue Life of Superalloy Udimet(Registered Trademark) 720

    Science.gov (United States)

    Gabb, Timothy P.; Telesman, Jack; Kantzos, Peter T.; Sweeney, Joseph W.; Browning, Paul F.

    2002-01-01

    The purpose of this study was to examine the effects of extended exposures on the near-surface fatigue resistance of a disk superalloy. Powder metallurgy processed, supersolvus heat-treated Udimet 720 (U720) fatigue specimens were exposed in air at temperatures from 650 to 705 C for 100 hr to over 1000 hr. They were then tested using conventional fatigue tests at 650 C to determine the effects of exposure on fatigue resistance. The exposures reduced life by up to 70% and increased the scatter in life, compared to unexposed levels. Fractographic evaluations indicated the failure mode was shifted by the exposures from internal to surface crack initiations. The increased scatter in life was related to the competition between internal crack initiations at inclusions or large grains producing longer lives, and surface crack initiations at an environmentally affected surface layer producing shorter lives.

  9. The hydrogen 700 project - 700 Bar Co

    International Nuclear Information System (INIS)

    Gambone, L.; Webster, C.

    2004-01-01

    'Full text:' Major automotive companies, including DaimlerChrysler, Ford, Hyundai, Nissan, PSA Peugeot-Citroen, and Toyota, are co-operating in the Hydrogen 700 project at Powertech to establish a global basis for high pressure hydrogen fuel systems for vehicles. The fuel systems will store compressed hydrogen on-board at pressures up to 700 bar (10,000psi). It is anticipated that the 700 bar storage pressure will provide hydrogen powered vehicles with a range comparable to the range of petroleum-fueled vehicles. The Hydrogen 700 project has contracted world leaders in high pressure technologies to provide 700 bar fuel system components for evaluation. The data from these tests will be used as the basis for the development of relevant standards and regulations. In a development that complements the Hydrogen 700 project, Powertech Labs has established the world's first 700 bar hydrogen station for fast filling operations. This prototype station will be used to evaluate the performance of the 700 bar vehicle fuel system components. The presentation will provide an overview of the Hydrogen 700 project. Safety issues surrounding the use of compressed hydrogen gas as a vehicle fuel, as well as the use of higher storage pressures, will be reviewed. Test data involving the fire testing of vehicles containing hydrogen fuel systems will be presented. The project is intended to result in the introduction of 700 bar fuel systems in the next generation of hydrogen powered vehicles. (author)

  10. Effects of long-time elevated temperature exposures on hot-isostatically-pressed power-metallurgy Udimet 700 alloys with reduced cobalt contents

    Science.gov (United States)

    Hart, F. H.

    1984-01-01

    Because almost the entire U.S. consumption of cobalt depends on imports, this metal has been designated "strategic'. The role and effectiveness of cobalt is being evaluated in commercial nickel-base superalloys. Udiment 700 type alloys in which the cobalt content was reduced from the normal 17% down to 12.7%, 8.5%, 4.3%, and 0% were prepared by standard powder metallurgy techniques and hot isostatically pressed into billets. Mechanical testing and microstructural investigations were performed. The mechanical properties of alloys with reduced cobalt contents which were heat-treated identically were equal or better than those of the standard alloy, except that creep rates tended to increase as cobalt was reduced. The effects of long time exposures at 760 C on mechanical properties and at 760 C and 845 C on microstructures were determined. Decreased tensile properties and shorter rupture lives with increased creep rates were observed in alloy modifications. The exposures caused gamma prime particle coarsening and formation of sigma phase in the alloys with higher cobalt contents. Exposure at 845 C also reduced the amount of MC carbides.

  11. Effectiveness of Shot Peening In Suppressing Fatigue Cracking At Non-Metallic Inclusions In Udimet(Registered Trademark)720

    Science.gov (United States)

    Barrie, Robert L.; Gabb, Timothy P.; Telesman, Jack; Kantzos, Peter T.; Prescenzi, Anthony; Biles, T.; Bonacuse, P. J.

    2006-01-01

    The fatigue lives of modern powder metallurgy disk alloys can be reduced over an order of magnitude by cracking at inherent non-metallic inclusions. The objective of this work was to study the effectiveness of shot peening in suppressing LCF crack initiation and growth at surface nonmetallic inclusions. Inclusions were carefully introduced at elevated levels during powder metallurgy processing of the nickel-base disk superalloy Udimet 720. Multiple strain-controlled fatigue tests were then performed on machined specimens with and without shot peened test sections at 427 C and 650 C. The low cycle fatigue lives and failure initiation sites varied as functions of inclusion content, shot peening, and fatigue conditions. A large majority of the failures in as-machined specimens with the introduced inclusions occurred at cracks initiating from inclusions intersecting the specimen surface. These inclusions reduced fatigue life by up to 100X, when compared to lives of material without inclusions residing at specimen surface. Large inclusions produced the greatest reductions in life for tests at low strain ranges and high strain ratios. Shot peening improved life in many cases by reducing the most severe effects of inclusions.

  12. Behaviour and damage of a superalloy prepared by hot isostatic compression

    International Nuclear Information System (INIS)

    Dubiez-Le-Goff, Sophie

    2003-01-01

    This work deals with the behavior and damage of Udimet 720 superalloy prepared by hot isostatic compression. This alloy is considered for manufacturing turbine disks of high temperature reactors (HTR). The material choice for HTR turbine disk depends on the following criteria: a good creep resistance until 700 C, a good behaviour under an helium impure atmosphere, a possible implementation under a disk of 1.5 m diameter. (author) [fr

  13. The microstructure and creep behavior of cold rolled udimet 188 sheet.

    Science.gov (United States)

    Boehlert, C J; Longanbach, S C

    2011-06-01

    Udimet 188 was subjected to thermomechanical processing (TMP) in an attempt to understand the effects of cold-rolling deformation on the microstructure and tensile-creep behavior. Commercially available sheet was cold rolled to varying amounts of deformation (between 5-35% reduction in sheet thickness) followed by a solution treatment at 1,464 K (1,191 °C) for 1 h and subsequent air cooling. This sequence was repeated four times to induce a high-volume fraction of low-energy grain boundaries. The resultant microstructure was characterized using electron backscattered diffraction. The effect of the TMP treatment on the high-temperature [1,033-1,088 K (760-815 °C)] creep behavior was evaluated. The measured creep stress exponents (6.0-6.8) suggested that dislocation creep was dominant at 1,033 K (760 °C) for stresses ranging between 100-220 MPa. For stresses ranging between 25-100 MPa at 1,033 K (760 °C), the stress exponents (2.3-2.8) suggested grain boundary sliding was dominant. A significant amount of grain boundary cracking was observed both on the surface and subsurface of deformed samples. To assess the mechanisms of crack nucleation, in situ scanning electron microscopy was performed during the elevated-temperature tensile-creep deformation. Cracking occurred preferentially along general high-angle grain boundaries (GHAB) and less than 25% of the cracks were found on low-angle grain boundaries (LAB) and coincident site lattice boundaries (CSLB). Creep rupture experiments were performed at T = 1,088 K (815 °C) and σ = 165 MPa and the greatest average time-to-rupture was exhibited by the TMP sheet with the greatest fraction of LAB+CSLB. However, a clear correlation was not exhibited between the grain boundary character distribution and the minimum creep rates. The findings of this work suggest that although grain boundary engineering may be possible for this alloy, simply relating the fraction of grain boundary types to the creep resistance is not

  14. Modeling and optimization of process variables of wire-cut electric discharge machining of super alloy Udimet-L605

    Directory of Open Access Journals (Sweden)

    Somvir Singh Nain

    2017-02-01

    Full Text Available This paper presents the behavior of Udimet-L605 after wire electric discharge machining and evaluating the WEDM process using sophisticated machine learning approaches. The experimental work is depicted on the basis of Taguchi orthogonal L27 array, considering six input variables and three interactions. Three models such as support vector machine algorithms based on PUK kernel, non-linear regression and multi-linear regression have been proposed to examine the variance between experimental and predicted outcome and preferred the preeminent model based on its evaluation parameters performance and graph analysis. The grey relational analysis is the relevant approach to obtain the best grouping of input variables for maximum material removal rate and minimum surface roughness. Based on statistical analysis, it has been concluded that pulse-on time, interaction between pulse-on time x pulse-off time, spark-gap voltage and wire tension are the momentous variable for surface roughness while the pulse-on time, spark-gap voltage and pulse-off time are the momentous variables for material removal rate. The micro structural and compositional changes on the surface of work material were examined by means of SEM and EDX analysis. The thickness of the white layer and the recast layer formation increases with increases in the pulse-on time duration.

  15. Low-Cobalt Powder-Metallurgy Superalloy

    Science.gov (United States)

    Harf, F. H.

    1986-01-01

    Highly-stressed jet-engine parts made with less cobalt. Udimet 700* (or equivalent) is common nickel-based superalloy used in hot sections of jet engines for many years. This alloy, while normally used in wrought condition, also gas-atomized into prealloyed powder-metallurgy (PM) product. Product can be consolidated by hot isostatically pressing (HIPPM condition) and formed into parts such as turbine disk. Such jet-engine disks "see" both high stresses and temperatures to 1,400 degrees F (760 degrees C).

  16. 25 CFR 700.543 - Gambling.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Gambling. 700.543 Section 700.543 Indians THE OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES Employee Responsibility and Conduct § 700.543 Gambling. An employee shall not sponsor or participate in any gambling activity...

  17. 15 CFR 700.2 - Introduction.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Introduction. 700.2 Section 700.2 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF... PRIORITIES AND ALLOCATIONS SYSTEM Overview § 700.2 Introduction. (a) Certain national defense and energy...

  18. 25 CFR 700.45 - Business.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Business. 700.45 Section 700.45 Indians THE OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES General Policies and Instructions Definitions § 700.45 Business. The term business means any lawful activity, except a nonprofit...

  19. 25 CFR 700.77 - Livestock.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Livestock. 700.77 Section 700.77 Indians THE OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES General Policies and Instructions Definitions § 700.77 Livestock. The term livestock shall mean all domesticated animals of every...

  20. 25 CFR 700.803 - Authority.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Authority. 700.803 Section 700.803 Indians THE OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES New Lands Grazing § 700.803 Authority. The regulations in this part are promulgated pursuant to section 10(b) of the...

  1. 25 CFR 700.703 - Authority.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Authority. 700.703 Section 700.703 Indians THE OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES New Lands Grazing § 700.703 Authority. It is within the authority of the Commissioner on Navajo and Hopi Indian Relocation to...

  2. 25 CFR 700.83 - Nonprofit organization.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Nonprofit organization. 700.83 Section 700.83 Indians THE OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES General Policies and Instructions Definitions § 700.83 Nonprofit organization. The term nonprofit organization...

  3. 25 CFR 700.467 - Construction costs.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Construction costs. 700.467 Section 700.467 Indians THE OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES Discretionary Funds § 700.467 Construction costs. Construction costs and costs relating to construction such as...

  4. 24 CFR 700.115 - Program costs.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Program costs. 700.115 Section 700... PUBLIC AND INDIAN HOUSING PROGRAMS) CONGREGATE HOUSING SERVICES PROGRAM § 700.115 Program costs. (a) Allowable costs. (1) Allowable costs for direct provision of supportive services includes the provision of...

  5. 25 CFR 700.549 - Employee organizations.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Employee organizations. 700.549 Section 700.549 Indians... Employee Responsibility and Conduct § 700.549 Employee organizations. An employee may not knowingly be a member of an organization of Government employees that advocates the overthrow of the United States...

  6. 25 CFR 700.93 - Relocation plan.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Relocation plan. 700.93 Section 700.93 Indians THE OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES General Policies and Instructions Definitions § 700.93 Relocation plan. The relocation plan shall be the plan prepared...

  7. 700 Area

    Data.gov (United States)

    Federal Laboratory Consortium — The 700 Area of the Hanford Site is located in downtown Richland.Called the Federal Office Building, the Richland Operations Site Manager and the Richland Operations...

  8. 32 CFR 700.826 - Physical security.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 5 2010-07-01 2010-07-01 false Physical security. 700.826 Section 700.826... Commanding Officers in General § 700.826 Physical security. (a) The commanding officer shall take appropriate... officer shall take action to protect and maintain the security of the command against dangers from fire...

  9. 25 CFR 700.99 - Salvage value.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Salvage value. 700.99 Section 700.99 Indians THE OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES General Policies and Instructions Definitions § 700.99 Salvage value. Salvage value means the probable sale price of an...

  10. 25 CFR 700.53 - Dwelling, replacement.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Dwelling, replacement. 700.53 Section 700.53 Indians THE... Policies and Instructions Definitions § 700.53 Dwelling, replacement. The term replacement dwelling means a dwelling selected by the head of a household as a replacement dwelling that meets the criteria of this...

  11. 32 CFR 700.832 - Environmental pollution.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 5 2010-07-01 2010-07-01 false Environmental pollution. 700.832 Section 700.832 National Defense Department of Defense (Continued) DEPARTMENT OF THE NAVY UNITED STATES NAVY REGULATIONS AND OFFICIAL RECORDS UNITED STATES NAVY REGULATIONS AND OFFICIAL RECORDS The Commanding Officer Commanding Officers in General § 700.832...

  12. Stirling Space Engine Program. Volume 2; Appendixes A, B, C and D

    Science.gov (United States)

    Dhar, Manmohan

    1999-01-01

    The objective of this program was to develop the technology necessary for operating Stirling power converters in a space environment and to demonstrate this technology in full-scale engine tests. Volume 2 of the report includes the following appendices: Appendix A: Heater Head Development (Starfish Heater Head Program, 1/10th Segment and Full-Scale Heat Pipes, and Sodium Filling and Processing); Appendix B: Component Test Power Converter (CTPC) Component Development (High-temperature Organic Materials, Heat Exchanger Fabrication, Beryllium Issues, Sodium Issues, Wear Couple Tests, Pressure Boundary Penetrations, Heating System Heaters, and Cooler Flow Test); Appendix C: Udimet Testing (Selection of the Reference Material for the Space Stirling Engine Heater Head, Udimet 720LI Creep Test Result Update, Final Summary of Space Stirling Endurance Engine Udimet 720L1 Fatigue Testing Results, Udimet 720l1 Weld Development Summary, and Udimet 720L1 Creep Test Final Results Summary), and Appendix D: CTPC Component Development Photos.

  13. 15 CFR 700.7 - Compliance.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Compliance. 700.7 Section 700.7 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS DEFENSE...

  14. 15 CFR 700.62 - Directives.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Directives. 700.62 Section 700.62 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS DEFENSE...

  15. 31 CFR 700.6 - Nuisances.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Nuisances. 700.6 Section 700.6 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FEDERAL LAW ENFORCEMENT..., unauthorized assembly, the creation of any hazard to persons or things, improper disposal of rubbish, or the...

  16. ICC 700-2012: 2012 National Green Building Standard (ICC 700)

    Science.gov (United States)

    Description of the ICC 700-2012: 2012 National Green Building Standard, a rating and certification system that aims to encourage increased environmental and health performance in residences and residential portions of buildings.

  17. 32 CFR 700.304 - Recommendations to Congress.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 5 2010-07-01 2010-07-01 false Recommendations to Congress. 700.304 Section 700... The Secretary of the Navy § 700.304 Recommendations to Congress. After first informing the Secretary of Defense, the Secretary of the Navy may make such recommendations to Congress relating to the...

  18. 25 CFR 700.81 - Monthly housing cost.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Monthly housing cost. 700.81 Section 700.81 Indians THE... Policies and Instructions Definitions § 700.81 Monthly housing cost. (a) General. The term monthly housing...) Computation of monthly housing cost for replacement dwelling. A person's monthly housing cost for a...

  19. 25 CFR 700.61 - Fair market value.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Fair market value. 700.61 Section 700.61 Indians THE OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES General Policies and Instructions Definitions § 700.61 Fair market value. Fair market value shall mean the value...

  20. 25 CFR 700.515 - Conflicts of interest.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Conflicts of interest. 700.515 Section 700.515 Indians... Employee Responsibility and Conduct § 700.515 Conflicts of interest. (a) A conflict of interest may exist... or herself, close friends, relatives, or business associates. A conflict of interest may also exist...

  1. 31 CFR 700.14 - Smoking.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Smoking. 700.14 Section 700.14 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FEDERAL LAW ENFORCEMENT TRAINING CENTER, DEPARTMENT OF THE TREASURY REGULATIONS GOVERNING CONDUCT IN OR ON THE FEDERAL LAW ENFORCEMENT TRAINING CENTER (FLETC) BUILDINGS AND...

  2. 25 CFR 700.269 - Accounting for disclosures.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Accounting for disclosures. 700.269 Section 700.269... Privacy Act § 700.269 Accounting for disclosures. (a) Maintenance of an accounting. (1) Where a record is... person or agency to whom the disclosure was made. (3) Accountings prepared under this section shall be...

  3. 32 CFR 700.337 - The Auditor General.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 5 2010-07-01 2010-07-01 false The Auditor General. 700.337 Section 700.337... Office of the Secretary of the Navy/the Staff Assistants § 700.337 The Auditor General. (a) The Auditor... Government auditing standards. (b) The Auditor General can provide information and may provide assistance and...

  4. 16 CFR 700.2 - Date of manufacture.

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Date of manufacture. 700.2 Section 700.2... MAGNUSON-MOSS WARRANTY ACT INTERPRETATIONS OF MAGNUSON-MOSS WARRANTY ACT § 700.2 Date of manufacture... after July 4, 1975. When a consumer purchases repair of a consumer product the date of manufacture of...

  5. 25 CFR 700.33 - Act (The Act).

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Act (The Act). 700.33 Section 700.33 Indians THE OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES General Policies and Instructions Definitions § 700.33 Act (The Act). (a) The Act. The Act is Pub. L. 93-531, (88 Stat...

  6. 40 CFR 141.700 - General requirements.

    Science.gov (United States)

    2010-07-01

    ... described in §§ 141.721 through 141.722. (7) Systems must address significant deficiencies identified in... 40 Protection of Environment 22 2010-07-01 2010-07-01 false General requirements. 141.700 Section 141.700 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS...

  7. 15 CFR 700.70 - General provisions.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false General provisions. 700.70 Section 700.70 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS...

  8. 15 CFR 700.61 - Rating Authorizations.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Rating Authorizations. 700.61 Section 700.61 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS...

  9. 15 CFR 700.60 - General provisions.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false General provisions. 700.60 Section 700.60 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS...

  10. 15 CFR 700.50 - General provisions.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false General provisions. 700.50 Section 700.50 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS...

  11. 15 CFR 700.31 - Metalworking machines.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Metalworking machines. 700.31 Section 700.31 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS...

  12. 15 CFR 700.75 - Compliance conflicts.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Compliance conflicts. 700.75 Section 700.75 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS...

  13. 30 CFR 700.10 - Information collection.

    Science.gov (United States)

    2010-07-01

    ... longer a surface coal mining and reclamation operation and thereby when regulatory jurisdiction may end... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Information collection. 700.10 Section 700.10 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR GENERAL...

  14. 15 CFR 700.6 - Official actions.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Official actions. 700.6 Section 700.6 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS DEFENSE...

  15. 21 CFR 584.700 - Hydrophobic silicas.

    Science.gov (United States)

    2010-04-01

    ...) Product. Amorphous fumed hydrophobic silica or precipitated hydrophobic silica (CAS Reg. No. 68611-0944... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Hydrophobic silicas. 584.700 Section 584.700 Food... DRUGS, FEEDS, AND RELATED PRODUCTS FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE IN FEED AND...

  16. 25 CFR 700.545 - Alcoholism and drug abuse.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Alcoholism and drug abuse. 700.545 Section 700.545... Employee Responsibility and Conduct § 700.545 Alcoholism and drug abuse. An employee who habitually uses... and drug abuse as serious and treatable illnesses. Excessive absence and poor work performance are two...

  17. ACR-700 advanced technologies

    International Nuclear Information System (INIS)

    Tapping, R.L.; Turner, C.W.; Yu, S.K.W.; Olmstead, R.; Speranzini, R.A.

    2004-01-01

    A successful advanced reactor plant will have optimized economics including reduced operating and maintenance costs, improved performance, and enhanced safety. Incorporating improvements based on advanced technologies ensures cost, safety and operational competitiveness of the ACR-700. These advanced technologies include modern configuration management; construction technologies; operational technology for the control centre and information systems for plant monitoring and analysis. This paper summarizes the advanced technologies used to achieve construction and operational improvements to enhance plant economic competitiveness, advances in the operational technology used for reactor control, and presents the development of the Smart CANDU suite of tools and its application to existing operating reactors and to the ACR-700. (author)

  18. 21 CFR 573.700 - Sodium nitrite.

    Science.gov (United States)

    2010-04-01

    ..., FEEDS, AND RELATED PRODUCTS FOOD ADDITIVES PERMITTED IN FEED AND DRINKING WATER OF ANIMALS Food Additive... as a preservative and color fixative in canned pet food containing fish, meat, and fish and meat... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium nitrite. 573.700 Section 573.700 Food and...

  19. 32 CFR 700.1056 - Command of a ship.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 5 2010-07-01 2010-07-01 false Command of a ship. 700.1056 Section 700.1056 National Defense Department of Defense (Continued) DEPARTMENT OF THE NAVY UNITED STATES NAVY REGULATIONS AND OFFICIAL RECORDS UNITED STATES NAVY REGULATIONS AND OFFICIAL RECORDS Precedence, Authority and Command Detail to Duty § 700.1056 Command of a...

  20. 10 CFR 2.700 - Scope of subpart G.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Scope of subpart G. 2.700 Section 2.700 Energy NUCLEAR... Formal Adjudications § 2.700 Scope of subpart G. The provisions of this subpart apply to and supplement... authorization for high-level radioactive waste repository noticed under §§ 2.101(f)(8) or 2.105(a)(5...

  1. Embrittlement of nickel-, cobalt-, and iron-base superalloys by exposure to hydrogen

    Science.gov (United States)

    Gray, H. R.

    1975-01-01

    Five nickel-base alloys (Inconel 718, Udimet 700, Rene 41, Hastelloy X, and TD-NiCr), one cobalt-base alloy (L-605), and an iron-base alloy (A-286) were exposed in hydrogen at 0.1 MN/sq m (15 psi) at several temperatures in the range from 430 to 980 C for as long as 1000 hours. These alloys were embrittled to varying degrees by such exposures in hydrogen. Embrittlement was found to be: (1) sensitive to strain rate, (2) reversible, (3) caused by large concentrations of absorbed hydrogen, and (4) not associated with any detectable microstructural changes in the alloys. These observations are consistent with a mechanism of internal reversible hydrogen embrittlement.

  2. 32 CFR 700.710 - Organization of a staff.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 5 2010-07-01 2010-07-01 false Organization of a staff. 700.710 Section 700.710... Commanders Staffs of Commanders § 700.710 Organization of a staff. (a) The term “staff” means those officers... operation of his or her command. (b) The officer detailed as chief of staff and aide to a fleet admiral or...

  3. 25 CFR 700.565 - Miscellaneous statutory provisions.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Miscellaneous statutory provisions. 700.565 Section 700... States Code, relating to bribery, graftm and conflicts of interest, as appropriate to the employees... registered under the Foreign Agents Registration Act (18 U.S.C. 219). ...

  4. 15 CFR 700.52 - Examples of assistance.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Examples of assistance. 700.52 Section 700.52 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS...

  5. 15 CFR 700.91 - Records and reports.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Records and reports. 700.91 Section 700.91 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS...

  6. 15 CFR 700.5 - Special priorities assistance.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Special priorities assistance. 700.5 Section 700.5 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS...

  7. 15 CFR 700.90 - Protection against claims.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Protection against claims. 700.90 Section 700.90 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS...

  8. 15 CFR 700.53 - Criteria for assistance.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Criteria for assistance. 700.53 Section 700.53 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS...

  9. 15 CFR 700.63 - Letters of Understanding.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Letters of Understanding. 700.63 Section 700.63 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS...

  10. 25 CFR 700.55 - Decent, safe, and sanitary dwelling.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Decent, safe, and sanitary dwelling. 700.55 Section 700... PROCEDURES General Policies and Instructions Definitions § 700.55 Decent, safe, and sanitary dwelling. (a) General. The term decent, safe, and sanitary dwelling means a dwelling which— (1) Meets applicable federal...

  11. 30 CFR 903.700 - Arizona Federal program.

    Science.gov (United States)

    2010-07-01

    ... Resources has jurisdiction over the mining of minerals, and oil and gas under Title 27 of the Arizona....700 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE ARIZONA § 903.700 Arizona Federal...

  12. 30 CFR 700.14 - Availability of records.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Availability of records. 700.14 Section 700.14 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR GENERAL... authority having jurisdiction over the area involved. (b) Other records or documents in the possession of...

  13. 32 CFR 700.1054 - Command of a naval base.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 5 2010-07-01 2010-07-01 false Command of a naval base. 700.1054 Section 700.1054 National Defense Department of Defense (Continued) DEPARTMENT OF THE NAVY UNITED STATES NAVY... Command Detail to Duty § 700.1054 Command of a naval base. The officer detailed to command a naval base...

  14. 32 CFR 700.872 - Ships and craft in drydock.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 5 2010-07-01 2010-07-01 false Ships and craft in drydock. 700.872 Section 700... Special Circumstances/ships in Naval Stations and Shipyards § 700.872 Ships and craft in drydock. (a) The... ship or craft, not in commission, is in a naval drydock, the provisions of this article shall apply...

  15. 32 CFR 700.1053 - Commander of a task force.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 5 2010-07-01 2010-07-01 false Commander of a task force. 700.1053 Section 700... Command Detail to Duty § 700.1053 Commander of a task force. (a) A geographic fleet commander, and any other naval commander, may detail in command of a task force, or other task command, any eligible...

  16. 700 C power plant technology. Status and challenge

    Energy Technology Data Exchange (ETDEWEB)

    Tschaffon, Helmut [E.ON Energie AG, Muenchen (Germany)

    2010-07-01

    Coal will remain an indispensable major source of energy for power generation in the world in the coming decades, because there are resources for hundreds of years. Coal fired power plants can be operated very flexible which gets increasing importance due to the stochastic input from regenerative energies like wind and solar energy. Sustainable technologies for cool-fired power plants have to be developed to optimise environmental protection and to save valuable resources and reduce CO{sub 2}-emissions. Future coal fired steam power plants aim an elevated steam temperature of about 700 C to reach a net efficiency of about 50%. This paper will give an overview over the status of the development of the 700 C technology and will highlight the challenges to be overcome before their commercial use. The European way to a 700 C Power plant started with the project AD700 in the year 1998. In this project the basic design of a 400 MW demo plant was done and some material tests and component qualifications for nickel-based alloys and new austenitic steels were started and terminated. AD700 delivered the basis of the design of the Component Test Facility COMTES700 (RFCS funded project with European manufacturers and utilities). COMTES 700 was operated between 2005 and 2009. It was integrated into the E.ON power plant Scholven in Germany to test mainly nickel based materials and power plant components. In the project NRWPP700 (2006-2010, funded by NRW and financed by European utilities) the detail design of the steam generator, piping system and turbine of a 500 MW power plant was done. In 7 material projects the qualification of components and materials was supported. At the same time of lot of national and international R and D projects (e.g. MARCKO and COORETEC) were performed. Due to the high amount of these projects they cannot be mentioned here in a detailed way. In 2007 the E.ON project 50plus was started. The aim was to plan and build a 700 C demo plant in

  17. Effects of cobalt on structure, microchemistry and properties of a wrought nickel-base superalloy

    Science.gov (United States)

    Jarrett, R. N.; Tien, J. K.

    1982-01-01

    The effect of cobalt on the basic mechanical properties and microstructure of wrought nickel-base superalloys has been investigated experimentally by systematically replacing cobalt by nickel in Udimet 700 (17 wt% Co) commonly used in gas turbine (jet engine) applications. It is shown that the room temperature tensile yield strength and tensile strength only slightly decrease in fine-grained (disk) alloys and are basically unaffected in coarse-grained (blading) alloys as cobalt is removed. Creep and stress rupture resistances at 760 C are found to be unaffected by cobalt level in the blading alloys and decrease sharply only when the cobalt level is reduced below 8 vol% in the disk alloys. The effect of cobalt is explained in terms of gamma prime strengthening kinetics.

  18. Effect of heating method on stress-rupture life

    Science.gov (United States)

    Bizon, P. T.; Calfo, F. D.

    1977-01-01

    The effect of radiant(furnace), resistance(electric current), burner(hot gas stream), and a combination of resistance and burner heating on intermediate time (100 to 300 hr) stress-rupture life and reduction of area was evaluated. All heating methods were studied using the nickel-based alloy Udimet 700 while all but burner heating were evaluated with the cobalt-based alloy Mar-M 509. Limited test results of eight other superalloys were also included in this study. Resistance heated specimens had about 20 to 30 percent of the stress-rupture life of radiant heated specimens. The limited burner heating data showed about a 50 percent life reduction as compared to the radiant heated tests. A metallurgical examination gave no explanation for these reductions.

  19. Toward a better understanding of strain incompatibilities at grain boundaries in the analysis of fatigue crack initiation at low temperature in the UdimetTM 720 Li superalloy

    Directory of Open Access Journals (Sweden)

    Larrouy Baptiste

    2014-01-01

    Full Text Available Low cycle fatigue properties of polycrystalline γ-γ′ Ni-based superalloys are dependent on many factors such as temperature, environment, grain size and distribution of the strengthening phases. Under LCF conditions at intermediate temperatures, an intergranular crack initiation could be observed. In this paper we propose to analyze the local conditions favouring such an intergranular cracking mode considering the high strength C&W UdimetTM720 Li alloy, widely used for manufacturing high pressure turbine disk for aeroengine applications. Tensile and fatigue tests were performed in air in the 20–465 ∘C range of temperature on micro-samples in order to focus on plasticity and damage processes developed near grain boundaries. A special attention was paid on the slip transfer between neighbouring grains taking into account their local crystallographic orientations. In some specific crystallographic configurations, small zones were detected at the tip of slip bands presenting an intense elastic/plastic activity. Although they are limited in size, they are associated to local crystalline rotations. High levels of local strain/stress were also evaluated in these volumes using an EBSD pattern cross correlation technique. The development of such specific zones was investigated at different stages of the tensile and LCF behaviour and was identified as leading to micro-cracks initiation for both solicitation modes.

  20. Creep fatigue of low-cobalt superalloys: Waspalloy, PM U 700 and wrought U 700

    Science.gov (United States)

    Leis, B. N.; Rungta, R.; Hopper, A. T.

    1983-01-01

    The influence of cobalt content on the high temperature creep fatigue crack initiation resistance of three primary alloys was evaluated. These were Waspalloy, Powder U 700, and Cast U 700, with cobalt contents ranging from 0 up to 17 percent. Waspalloy was studied at 538 C whereas the U 700 was studied at 760 C. Constraints of the program required investigation at a single strain range using diametral strain control. The approach was phenomenological, using standard low cycle fatigue tests involving continuous cycling tension hold cycling, compression hold cycling, and symmetric hold cycling. Cycling in the absence of or between holds was done at 0.5 Hz, whereas holds when introduced lasted 1 minute. The plan was to allocate two specimens to the continuous cycling, and one specimen to each of the hold time conditions. Data was taken to document the nature of the cracking process, the deformation response, and the resistance to cyclic loading to the formation of small cracks and to specimen separation. The influence of cobalt content on creep fatigue resistance was not judged to be very significant based on the results generated. Specific conclusions were that the hold time history dependence of the resistance is as significant as the influence of cobalt content and increased cobalt content does not produce increased creep fatigue resistance on a one to one basis.

  1. The future 700 MWe pressurized heavy water reactor

    International Nuclear Information System (INIS)

    Bhardwaj, S.A.

    2006-01-01

    The design of a 700 MWe pressurized heavy water reactor has been developed. The design is based on the twin 540 MWe reactors at Tarapur of which the first unit has been made critical in less than 5 years from construction commencement. In the 700 MWe design boiling of the coolant, to a limited extent, has been allowed near the channel exit. While making the plant layout more compact, emphasis has been on constructability. Saving in capital cost of about 15%, over the present units, is expected. The paper describes salient design features of 700 MWe pressurized heavy water reactor

  2. 15 CFR 700.74 - Violations, penalties, and remedies.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Violations, penalties, and remedies. 700.74 Section 700.74 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE...

  3. 15 CFR 700.1 - Purpose of this regulation.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Purpose of this regulation. 700.1 Section 700.1 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS...

  4. 32 CFR 700.860 - Customs and immigration inspections.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 5 2010-07-01 2010-07-01 false Customs and immigration inspections. 700.860... Commanding Officer Commanding Officers Afloat § 700.860 Customs and immigration inspections. (a) The... a customs officer or immigration officer of the United States to make on board the ship or aircraft...

  5. 32 CFR 700.320 - The Civilian Executive Assistants.

    Science.gov (United States)

    2010-07-01

    ... the Navy. (b) Each Civilian Executive Assistants, within his or her assigned area of responsibility... 32 National Defense 5 2010-07-01 2010-07-01 false The Civilian Executive Assistants. 700.320... of the Navy The Office of the Secretary of the Navy/the Civilian Executive Assistants § 700.320 The...

  6. 32 CFR 700.705 - Observance of international law.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 5 2010-07-01 2010-07-01 false Observance of international law. 700.705 Section... Other Commanders Titles and Duties of Commanders § 700.705 Observance of international law. At all times, commanders shall observe, and require their commands to observe, the principles of international law. Where...

  7. 29 CFR 825.700 - Interaction with employer's policies.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Interaction with employer's policies. 825.700 Section 825.700 Labor Regulations Relating to Labor (Continued) WAGE AND HOUR DIVISION, DEPARTMENT OF LABOR OTHER LAWS THE FAMILY AND MEDICAL LEAVE ACT OF 1993 Effect of Other Laws, Employer Practices, and Collective...

  8. 25 CFR 700.79 - Marriage.

    Science.gov (United States)

    2010-04-01

    ... Instructions Definitions § 700.79 Marriage. Marriage is a legally recorded marriage or a traditional commitment between a man or woman recognized by the law of the Hopi Tribe or the Navajo Tribe. ...

  9. 21 CFR 700.25 - Tamper-resistant packaging requirements for cosmetic products.

    Science.gov (United States)

    2010-04-01

    ... cosmetic products. 700.25 Section 700.25 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) COSMETICS GENERAL Requirements for Specific Cosmetic Products § 700.25 Tamper-resistant packaging requirements for cosmetic products. (a) General. Because most cosmetic liquid...

  10. 15 CFR 700.3 - Priority ratings and rated orders.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Priority ratings and rated orders. 700.3 Section 700.3 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE...

  11. 15 CFR 700.73 - Notification of failure to comply.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Notification of failure to comply. 700.73 Section 700.73 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE...

  12. 13 CFR 120.700 - What is the Microloan Program?

    Science.gov (United States)

    2010-01-01

    ... to Intermediaries and other qualified nonprofit entities to be used for marketing, management, and... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false What is the Microloan Program? 120.700 Section 120.700 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS...

  13. 46 CFR 115.700 - Permission for repairs and alterations.

    Science.gov (United States)

    2010-10-01

    ... replacement in kind, of electrical wiring, fuel lines, tanks, boilers and other pressure vessels, and steering... 46 Shipping 4 2010-10-01 2010-10-01 false Permission for repairs and alterations. 115.700 Section... AND CERTIFICATION Repairs and Alterations § 115.700 Permission for repairs and alterations. (a...

  14. 46 CFR 176.700 - Permission for repairs and alterations.

    Science.gov (United States)

    2010-10-01

    ... repair or replacement, other than replacement in kind, of electrical wiring, fuel lines, tanks, boilers... 46 Shipping 7 2010-10-01 2010-10-01 false Permission for repairs and alterations. 176.700 Section... (UNDER 100 GROSS TONS) INSPECTION AND CERTIFICATION Repairs and Alterations § 176.700 Permission for...

  15. 15 CFR 700.11 - Priority ratings.

    Science.gov (United States)

    2010-01-01

    ... OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS DEFENSE PRIORITIES AND ALLOCATIONS SYSTEM Industrial Priorities § 700.11 Priority ratings. (a) Levels of...

  16. 15 CFR 700.14 - Preferential scheduling.

    Science.gov (United States)

    2010-01-01

    ...) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS DEFENSE PRIORITIES AND ALLOCATIONS SYSTEM Industrial Priorities § 700.14 Preferential scheduling. (a) A...

  17. 15 CFR 700.21 - Application for priority rating authority.

    Science.gov (United States)

    2010-01-01

    ... allocations authorities. (e) Commerce will inform the Department of Energy of the results of its analysis. If... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Application for priority rating authority. 700.21 Section 700.21 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign...

  18. 28 CFR 700.24 - Security of systems of records.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Security of systems of records. 700.24... Records Under the Privacy Act of 1974 § 700.24 Security of systems of records. (a) The Office Administrator or Security Officer shall be responsible for issuing regulations governing the security of systems...

  19. 15 CFR 700.81 - Appeals.

    Science.gov (United States)

    2010-01-01

    ... INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS DEFENSE... Economic Security under § 700.80, may appeal to the Assistant Secretary for Export Administration, U.S... Office of the Assistant Secretary for Export Administration, Bureau of Industry and Security, U.S...

  20. 7 CFR 51.700 - Discoloration.

    Science.gov (United States)

    2010-01-01

    ... § 51.700 Discoloration. Discoloration means russeting of light shade of golden brown caused by rust..., provided no discoloration caused by melanose or other means may affect the appearance of the fruit to a... Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing...

  1. 25 CFR 700.119 - Establishment of fair market value.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Establishment of fair market value. 700.119 Section 700... value. (a) General. The Commission shall establish the amount of fair market value to be offered to the... recommendations as to the fair market value of the habitations and/or improvements; or (2) The fair market value...

  2. 13 CFR 127.700 - What penalties may be imposed under this part?

    Science.gov (United States)

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false What penalties may be imposed under this part? 127.700 Section 127.700 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION WOMEN-OWNED SMALL BUSINESS FEDERAL CONTRACT ASSISTANCE PROCEDURES Penalties § 127.700 What penalties may...

  3. Fatigue and creep cracking of nickel alloys for 700 C steam turbines

    International Nuclear Information System (INIS)

    Berger, C.; Granacher, J.; Thoma, A.; Roesler, J.; Del Genovese, D.

    2001-01-01

    Four materials of the types Inconel 706 (two heat treatment states), Inconel 617, and Waspaloy were tested as shaft materials for 700 to 720 C steam turbines. At an extrapolation time ratio of 10, Waspaloy was expected to have the highest creep strength (about 270 MPa at 700 C), with values of about 140 MPa at 700 C for Inconel 617. A preliminary evaluation of the 700 C creep rupture tests showed the highest creep rupture resistance for Inconel 617, followed by Waspaloy and Inconel 706 [de

  4. High-power circulator test results at 350 and 700 MHz

    International Nuclear Information System (INIS)

    Roybal, W.; Bradley, J.T.; Rees, D.E.

    2000-01-01

    The high-power RF systems for the Accelerator Production of Tritium (APT) program require high-power circulators at 350 MHz and 700 MHz to protect 1 MW Continuous Wave (CW) klystrons from reflected power. The 350 MHz circulator is based on the CERN, EXF, and APS designs and has performed very well. The 700 MHz circulator is a new design. Prototype 700 MHz circulators have been high-power tested at Los Alamos National Laboratory (LANL). The first of these circulators has satisfied performance requirements. The circulator requirements, results from the testing, and lessons learned from this development are presented and discussed

  5. Development of service-relevant materials data and economic quality assurance and machining procedures for gas turbine blades. Final report; Entwicklung betriebsrelevanter Werkstoffkennwerte und wirtschaftlicher Qualitaetssicherungs- und Bearbeitungsverfahren fuer GT-Schaufeln. Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Buergel, R.; Rechtenbacher, H.

    1994-01-01

    In the frame of the reported project, together with the programme partners, optimization of service relevant properties as well as modification of manufacturing procedures for the forged alloy Nimonic 101 were achieved. These results are directly implementable into serial production and cause improved service reliability and economic benefit. For the forged alloy Udimet 720 materials data were generated in accordance with the programme plan. The final evaluation for this alloy will be performed by the project partner Siemens-KWU. The qualification of fine-grained investment cast blades of IN 792 for large rear=stage blading is not yet fully completed. Three major questions are lacking final answers: - Does a stress rupture strength advantage exist over the forged alloy Udimet 720/coarse/grained? - Can a high cycle fatigue strength as high as that for Udimet 720/coarse-grained be met reproducibly? - Does the investment cast blades offer a cost advantage over the forged ones - technical qualification assumed? The programme helped significantly in preparing the right answers to these questions. (orig.) [Deutsch] Im Rahmen des berichteten Teilvorhabens ist es in Zusammenarbeit mit den Projektpartnern gelungen, fuer die Schmiedelegierung Nimonic 101 die betriebsrelevanten Eigenschaften zu optimieren, sowie die Schaufelherstellung so zu modifizieren, dass die Betriebszuverlaessigkeit verbessert wird. Diese Ergebnisse sind direkt in die Serienfertigung implementierbar und damit wirtschaftlich nutzbar. Fuer die Schmiedelegierung Udimet 720 wurden im Rahmen des Projektverbundes Werkstoffkennwerte ermittelt. Die Gesamtauswertung fuer diesen Werkstoff erfolgt von Projektpartner Siemens-KWU. Das Bild zur Qualifikation feinkoerniger Feingussschaufeln ist noch nicht restlos klar. Drei wesentliche, noch abschliessend zu beantwortende Fragen sind: - Ergibt sich ein Zeitstandfestigkeitsvorteil gegenueber der Schmiedelegierung Udimet 720/Grobkorn? - Laesst sich reproduzierbar eine

  6. 20 CFR 410.700 - Background.

    Science.gov (United States)

    2010-04-01

    ... LUNG BENEFITS (1969- ) Rules for the Review of Denied and Pending Claims Under the Black Lung Benefits Reform Act (BLBRA) of 1977 § 410.700 Background. (a) The Black Lung Benefits Reform Act of 1977 broadens... establish entitlement to black lung benefits. Section 435 of the Black Lung Benefits Reform Act of 1977...

  7. 28 CFR 700.22 - Request for accounting of record disclosures.

    Science.gov (United States)

    2010-07-01

    ... disclosures. (a) An individual may request the Office to provide him with an accounting of those other... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Request for accounting of record disclosures. 700.22 Section 700.22 Judicial Administration OFFICE OF INDEPENDENT COUNSEL PRODUCTION OR...

  8. 25 CFR 700.723 - Control of livestock disease and parasites.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Control of livestock disease and parasites. 700.723... RELOCATION PROCEDURES New Lands Grazing § 700.723 Control of livestock disease and parasites. Whenever livestock within the New Lands become infected with contagious or infectious disease or parasites or have...

  9. 25 CFR 700.727 - Impoundment and disposal of unauthorized livestock.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Impoundment and disposal of unauthorized livestock. 700... RELOCATION PROCEDURES New Lands Grazing § 700.727 Impoundment and disposal of unauthorized livestock. Unauthorized livestock within any range unit of the New Lands which are not removed therefrom within the...

  10. Mechanical Properties of Domestic T700 Grade Carbon Fibers/QY9611 BMI Matrix Composites

    Directory of Open Access Journals (Sweden)

    LI Guoli

    2017-04-01

    Full Text Available The morphologies,surface energies and surface chemical properties of the domestic T700 grade carbon fiber and the T700S carbon fiber were characterized by using scanning electronic microscopy (SEM, inverse gas chromatography(IGC and X-ray photoelectron spectroscopy (XPSrespectively.The mechanical properties of the two carbon fibers/QY9611 composites were also discussed. The results indicate that the surface properties of carbon fibers have an important influence on the interfacial properties of composites. The interfacial properties of domestic T700 grade carbon fibers/QY9611 composite at room temperature/dry conditions are superior to T700S/QY9611 composite. The toughness of domestic T700 grade carbon fibers/QY9611composite is outstanding as well. The value of CAI has reached the level of foreign advanced composite IM7/5250-4. After hydrothermal treatment,the interfacial strength of domestic T700 grade carbon fibers/QY9611 composite is equal to that of T700S/QY9611 composite. It shows that domestic T700 grade carbon fibers/QY9611 composite has good hydrothermal-resistant properties.

  11. 32 CFR 700.325 - The Assistant Secretary of the Navy (Installations and Environment).

    Science.gov (United States)

    2010-07-01

    ... (Installations and Environment). 700.325 Section 700.325 National Defense Department of Defense (Continued... Assistants § 700.325 The Assistant Secretary of the Navy (Installations and Environment). The Assistant Secretary of the Navy (Installations and Environment) is responsible for: (a) Policy relating to Navy...

  12. 700 bar hydrogen cylinder design, testing and certification

    International Nuclear Information System (INIS)

    Duncan, M.

    2004-01-01

    'Full text:' Light weight and high pressure cylinders for compressed hydrogen storage are essential components for fuel cell vehicles. Storage volume and mass are two key considerations. Current on-board hydrogen storage systems are based on a maximum pressure of 350 bar. While 350 bar systems are excellent solutions for many applications, some situations required higher storage densities due to space restrictions. As a result significant research and development work has been expended by cylinder manufacturers, systems providers, testing agencies and automotive manufacturers to develop 700 bar systems to reduce storage volume. Dynetek Industries Ltd has proactively developed a range of 700 bar storage cylinders based on a seamless aluminum liner over wrapped with a carbon fiber composite. This paper presents the challenges and processes involved in the design, testing and certification of the Dynetek Industries Ltd 700 bar cylinder. The paper also provides reasoning for further volume and mass optimization of compressed hydrogen cylinders by incorporating realistic cylinder usage parameters into standards. In particular the overly conservative fill life requirement for cylinders will be examined. (author)

  13. 32 CFR 700.846 - Status of logs.

    Science.gov (United States)

    2010-07-01

    ... Officers Afloat § 700.846 Status of logs. The deck log, the engineering log, the compass record, the bearing hooks, the engineer's bell book, and any records generated by automated data logging equipment...

  14. 24 CFR 700.135 - Professional assessment committee.

    Science.gov (United States)

    2010-04-01

    ... this section, shall recommend services appropriate to the functional abilities and needs of each...)(A) and (B). PAC members are subject to the conflict of interest provisions in section 700.175(b). (2...

  15. 25 CFR 700.513 - Business dealings on behalf of the government.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Business dealings on behalf of the government. 700.513... RELOCATION PROCEDURES Employee Responsibility and Conduct § 700.513 Business dealings on behalf of the... the Commission. Employees shall observe courtesy, consideration and promptness in dealing with clients...

  16. 31 CFR 700.9 - Photographs for news, advertising, or commercial purposes.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Photographs for news, advertising, or commercial purposes. 700.9 Section 700.9 Money and Finance: Treasury Regulations Relating to Money and... Photographs for news, advertising, or commercial purposes. Photographs for news, advertising, or commercial...

  17. 15 CFR 700.30 - Priorities and allocations in a national emergency.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Priorities and allocations in a national emergency. 700.30 Section 700.30 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY...

  18. 15 CFR 700.4 - Priorities and allocations in a national emergency.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Priorities and allocations in a national emergency. 700.4 Section 700.4 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY...

  19. 15 CFR 700.92 - Applicability of this regulation and official actions.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Applicability of this regulation and official actions. 700.92 Section 700.92 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY...

  20. 21 CFR 700.15 - Use of certain halogenated salicylanilides as ingredients in cosmetic products.

    Science.gov (United States)

    2010-04-01

    ... ingredients in cosmetic products. 700.15 Section 700.15 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) COSMETICS GENERAL Requirements for Specific Cosmetic Products § 700.15 Use of certain halogenated salicylanilides as ingredients in cosmetic products. (a...

  1. 21 CFR 700.16 - Use of aerosol cosmetic products containing zirconium.

    Science.gov (United States)

    2010-04-01

    ... zirconium. 700.16 Section 700.16 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... cosmetic products containing zirconium. (a) Zirconium-containing complexes have been used as an ingredient... indicates that certain zirconium compounds have caused human skin granulomas and toxic effects in the lungs...

  2. 25 CFR 700.509 - Duties of the designated agency ethics official.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Duties of the designated agency ethics official. 700.509... RELOCATION PROCEDURES Employee Responsibility and Conduct § 700.509 Duties of the designated agency ethics official. The Designated Agency Ethics Official shall coordinate and manage the agency's ethics program...

  3. 47 CFR 90.1408 - Organization and structure of the 700 MHz public/private partnership.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Organization and structure of the 700 MHz public/private partnership. 90.1408 Section 90.1408 Telecommunication FEDERAL COMMUNICATIONS COMMISSION... Partnership § 90.1408 Organization and structure of the 700 MHz public/private partnership. (a) The Upper 700...

  4. 47 CFR 27.1308 - Organization and structure of the 700 MHz public/private partnership.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Organization and structure of the 700 MHz public/private partnership. 27.1308 Section 27.1308 Telecommunication FEDERAL COMMUNICATIONS COMMISSION... Partnership § 27.1308 Organization and structure of the 700 MHz public/private partnership. (a) The Upper 700...

  5. 21 CFR 700.19 - Use of methylene chloride as an ingredient of cosmetic products.

    Science.gov (United States)

    2010-04-01

    ... cosmetic products. 700.19 Section 700.19 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) COSMETICS GENERAL Requirements for Specific Cosmetic Products § 700.19 Use of methylene chloride as an ingredient of cosmetic products. (a) Methylene chloride has been used...

  6. 15 CFR 700.15 - Extension of priority ratings.

    Science.gov (United States)

    2010-01-01

    ...) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS DEFENSE PRIORITIES AND ALLOCATIONS SYSTEM Industrial Priorities § 700.15 Extension of priority ratings. (a...

  7. 15 CFR 700.20 - Use of priority ratings.

    Science.gov (United States)

    2010-01-01

    ...) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS DEFENSE PRIORITIES AND ALLOCATIONS SYSTEM Industrial Priorities for Energy Programs § 700.20 Use of...

  8. 22 CFR 208.700 - When may the suspending official issue a suspension?

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 1 2010-04-01 2010-04-01 false When may the suspending official issue a suspension? 208.700 Section 208.700 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT GOVERNMENTWIDE...) through (d); and (c) Immediate action is necessary to protect the public interest. ...

  9. 15 CFR 700.10 - Delegation of authority.

    Science.gov (United States)

    2010-01-01

    ...) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS DEFENSE PRIORITIES AND ALLOCATIONS SYSTEM Industrial Priorities § 700.10 Delegation of authority. (a) The... respect to industrial resources have been delegated to the Secretary of Commerce under Executive Order...

  10. 15 CFR 700.17 - Use of rated orders.

    Science.gov (United States)

    2010-01-01

    ...) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS DEFENSE PRIORITIES AND ALLOCATIONS SYSTEM Industrial Priorities § 700.17 Use of rated orders. (a) A person...

  11. 25 CFR 700.541 - Fraud or false statement in a Government matter.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Fraud or false statement in a Government matter. 700.541... RELOCATION PROCEDURES Employee Responsibility and Conduct § 700.541 Fraud or false statement in a Government..., applications for employment, personnel security forms, requests for travel reimbursement, client certification...

  12. 48 CFR 3.700 - Scope of subpart.

    Science.gov (United States)

    2010-10-01

    ... BUSINESS PRACTICES AND PERSONAL CONFLICTS OF INTEREST Voiding and Rescinding Contracts 3.700 Scope of... for bribery, conflict of interest, disclosure or receipt of contractor bid or proposal information or source selection information in exchange for a thing of value or to give anyone a competitive advantage...

  13. Three-dimensional studies of the 700 MWe steam generator design

    International Nuclear Information System (INIS)

    John, B.; Pietralik, J.

    2006-01-01

    The next stage in the Indian nuclear power programme envisions building 700 MWe Indian Pressurized Heavy Water Reactor (IPHWR) units. This involves up-rating of all the plant equipment including the reactor, steam generators (SGs), turbo-generator, major pumps, etc. The SG used in the current generation of 540 MWe IPHWRs, is a mushroom type, inverted U-tube, natural-circulation SG. The 700 MWe SG is of the same type and has the same tube bundle design and the same heat transfer area. The tube diameter, tube pitch, and outer diameter of the SG sections are the same as for the 540 MWe SG. The geometry of the feedwater header, the flow restrictor in the downcomer and the flow distribution plate are different in the two designs. The changes were required due to a 26% increase in steam flow rate while maintaining the same circulation ratio. This paper describes the design of the 700 MWe SG and a thermalhydraulic analysis using a one-dimensional, in-house code and a three-dimensional code called THIRST developed by AECL. The codes were validated against the 540 MWe SG data. The analysis was made for the 700 MWe SG for two versions: with and without integral preheater. The results of the THIRST runs were used for a flow-induced vibration analysis. The results of the flow-induced vibration analysis show that the vibrations are not excessive. (author)

  14. 24 CFR 700.120 - Eligible supportive services.

    Science.gov (United States)

    2010-04-01

    ... section 802(k)(16) and in section 700.105. (c) Meal services shall meet the following guidelines: (1) Type... requirements of conditions such as diabetes and hypertension. Grantees should attempt to meet the dietary needs... minimum daily dietary allowances as established by the Food and Nutrition Board of the National Academy of...

  15. 12 CFR 1805.700 - Evaluation and selection-general.

    Science.gov (United States)

    2010-01-01

    ... Section 1805.700 Banks and Banking COMMUNITY DEVELOPMENT FINANCIAL INSTITUTIONS FUND, DEPARTMENT OF THE TREASURY COMMUNITY DEVELOPMENT FINANCIAL INSTITUTIONS PROGRAM Evaluation and Selection of Applications... Applicants that vary by institution type, total asset size, stage of organizational development, markets...

  16. 15 CFR 700.12 - Elements of a rated order.

    Science.gov (United States)

    2010-01-01

    ...) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS DEFENSE PRIORITIES AND ALLOCATIONS SYSTEM Industrial Priorities § 700.12 Elements of a rated order. Each...

  17. 25 CFR 700.241 - Request for records.

    Science.gov (United States)

    2010-04-01

    ... which the requester is willing to pay. Requesters are notified that under § 700.251, the failure to..., both on the envelope and on the face of the request, with the legend “FREEDOM OF INFORMATION REQUEST.” The failure of a request to bear such a legend will not disqualify a request from processing under the...

  18. 24 CFR 700.150 - Program participant fees.

    Science.gov (United States)

    2010-04-01

    ... receiving more than one meal per day, seven days per week, shall be reasonable and shall equal between 10... 700.145(a). Each program participant shall pay CHSP fees as stated in paragraphs (d) and (e) of this... paragraph (d)(1) of this section shall be in an amount equal to 10 percent of the adjusted income of the...

  19. COSMO OIL is the series station of 700 store reduction; Kosumo, keiretsu kyuyujo 700 ten sakugen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-10-01

    Past petroleum each sale company accelerates the reduction of the franchise gas station. 700 stores in which COSMO OIL corresponds to whole 11% further than the end the preceding fiscal year including the transfer to other company by the 99 fiscal year end are reduced. In this other, Idemitsu Kosan also reduces 600 stores which correspond to whole 9%. As the profit deteriorates in prolonging sale competition, and as the unprofitability store can not be maintained, be. (translated by NEDO)

  20. 45 CFR 2516.700 - What matching funds are required?

    Science.gov (United States)

    2010-10-01

    ... COMMUNITY SERVICE SCHOOL-BASED SERVICE-LEARNING PROGRAMS Funding Requirements § 2516.700 What matching funds... for that share through State sources, local sources, or Federal sources (other than funds made...

  1. 32 CFR 700.880 - Duties of the prospective commanding officer of a ship.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 5 2010-07-01 2010-07-01 false Duties of the prospective commanding officer of a ship. 700.880 Section 700.880 National Defense Department of Defense (Continued) DEPARTMENT OF THE NAVY UNITED STATES NAVY REGULATIONS AND OFFICIAL RECORDS UNITED STATES NAVY REGULATIONS AND OFFICIAL RECORDS The Commanding Officer Special...

  2. Evolution of Flux Mapping System (FMS) from 540 MWe to 700 MWe Indian PHWR: design perspective

    International Nuclear Information System (INIS)

    Sonavani, Manojkumar; Kelkar, M.G.; Singhvi, P.K.; Roy, S.; Ingle, V.J.

    2013-01-01

    The Flux Mapping System (FMS) of 700 MWe PHWR computes a detailed flux/power distribution of the reactor core using modal synthesis method and is also generate setback on different parameters by monitoring thermal neutron flux at more than 100 points inside the reactor core. These types of setbacks are introduced first time in Indian PHWRs. The paper brings out the Evolution of Flux Mapping System (FMS) from 540 MWe to 700 MWe and the overall design philosophy. The paper emphasizes on comparisons between 540 MWe and 700 MWe design, considerations for architectural design and setbacks for 700 MWe. (author)

  3. Radiological environmental monitoring with LiF-700-H dosemeters

    International Nuclear Information System (INIS)

    Scarnichia, E.; Levanon, I.; Andres, P.; Miani, C.; Ramirez, S.

    2011-10-01

    Since 2008 a radiological environmental monitoring with LiF-700-H has been carried out as a result of increasing the Ra-6 research reactor core power. The information obtained is used to evaluate and to quantify analytically the air kerma rate, the fading and the associated uncertainty by developing software tools (deconvolution and uncertainty algorithms). LiF-700-H dosemeters were chosen because of their high sensitivity to low air kerma rates. They show a very good stability and a negligible fading for two-month working periods. The air kerma rate detection limit (based on the 3σ criterion) during these working periods is about 0.4 n Gy/h. Air kerma rates of about 70 n Gy/h are measured with this detection limit. Following the Nist guidelines, an algorithm was developed in order to find the associated uncertainty. It considers several aspects, such as the source activity decay, distance source-dosemeter during the calibration procedure, irradiation time, calibration factor, dosemeter readout, dosemeter sensitivity, TLD reader stability and fading. The associated uncertainty is found to be about 25% for a 95% confidence interval (k = 2.025), which can be considered acceptable when taking into account the very low air kerma rates estimated. The LiF-700-H response to different energies and its relationship with climate changes over the calendar year are planned as future tasks. (Author)

  4. 21 CFR 700.14 - Use of vinyl chloride as an ingredient, including propellant of cosmetic aerosol products.

    Science.gov (United States)

    2010-04-01

    ... propellant of cosmetic aerosol products. 700.14 Section 700.14 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) COSMETICS GENERAL Requirements for Specific Cosmetic Products § 700.14 Use of vinyl chloride as an ingredient, including propellant of cosmetic aerosol products...

  5. 32 CFR 37.700 - What are the requirements for supplies?

    Science.gov (United States)

    2010-07-01

    ... AGREEMENT REGULATIONS TECHNOLOGY INVESTMENT AGREEMENTS Award Terms Affecting Participants' Financial, Property, and Purchasing Systems Property § 37.700 What are the requirements for supplies? Your expenditure...

  6. Refinement and fracture mechanisms of as-cast QT700-6 alloy by alloying method

    Directory of Open Access Journals (Sweden)

    Min-qiang Gao

    2017-01-01

    Full Text Available The as-cast QT700-6 alloy was synthesized with addition of a certain amount of copper, nickel, niobium and stannum elements by alloying method in a medium frequency induction furnace, aiming at improving its strength and toughness. Microstructures of the as-cast QT700-6 alloy were observed using a scanning-electron microscope (SEM and the mechanical properties were investigated using a universal tensile test machine. Results indicate that the ratio of pearlite/ferrite is about 9:1 and the graphite size is less than 40 μm in diameter in the as-cast QT700-6 alloy. The predominant refinement mechanism is attributed to the formation of niobium carbides, which increases the heterogeneous nucleus and hinders the growth of graphite. Meanwhile, niobium carbides also exist around the grain boundaries, which improve the strength of the ductile iron. The tensile strength and elongation of the as-cast QT700-6 alloy reach over 700 MPa and 6%, respectively, when the addition amount of niobium is 0.8%. The addition of copper and nickel elements contributed to the decrease of eutectoid transformation temperature, resulting in the decrease of pearlite lamellar spacing (about 248 nm, which is also beneficial to enhancing the tensile strength. The main fracture mechanism is cleavage fracture with the appearance of a small amount of dimples.

  7. B700, a murine melanoma-specific antigen, binds Vitamin D3; conservation of binding among albuminoid molecules

    International Nuclear Information System (INIS)

    Farzaneh, N.K.; Walden, T.L. Jr.; Hearing, V.J.; Gersten, D.M.

    1990-01-01

    B700, a murine melanoma-specific antigen, is a member of the serum albumin protein family. Other members of this family include serum albumin (SMA), a-fetoprotein (AFP), vitamin D binding protein (DBP), and C700. The primary structure and biochemical functions of B700, as well as its in vivo metabolic fate are largely unknown. The authors examined the functional characteristics of MSA, AFP, and DBP, and for their ability to specifically bind [ 3 H]-1,25-dihydroxy-vitamin D 3 . Scatchard analysis revealed a single binding site for B700 with a Kd of 51,000 M and a Bmax of 4.51 x 10 -7 . There is no significant difference between the Kd and Bmax values among the albuminoid proteins. However, differences in the binding sites could be distinguished by competition of the 1,25-dihydroxy vitamin D 3 with other steroids. 2nM of vitamin D 3 , vitamin D 2 , or estrogen competed for the specific binding of 1,25-dihydroxy vitamin D 3 by B700 but not by DBP. The MSA binding site for 1,25 dihydroxy vitamin D 3 more closely resembles that of DBP than B700. These data indicate that the binding function of the albuminoid proteins has been conserved in the B700 melanoma antigen

  8. 42 CFR 438.700 - Basis for imposition of sanctions.

    Science.gov (United States)

    2010-10-01

    ... SERVICES (CONTINUED) MEDICAL ASSISTANCE PROGRAMS MANAGED CARE Sanctions § 438.700 Basis for imposition of... among enrollees on the basis of their health status or need for health care services. This includes termination of enrollment or refusal to reenroll a recipient, except as permitted under the Medicaid program...

  9. 25 CFR 700.165 - Ineligible moving and related expenses.

    Science.gov (United States)

    2010-04-01

    ... expenses. A displaced person is not entitled to payment for— (a) The cost of moving any structure or other...) Physical changes at replacement location of business, farm or nonprofit organization, except as provided at § 700.157; or (g) Any additional expense of a business, farm, or nonprofit organization incurred because...

  10. Hot corrosion of low cobalt alloys

    Science.gov (United States)

    Stearns, C. A.

    1982-01-01

    The hot corrosion attack susceptibility of various alloys as a function of strategic materials content are investigated. Preliminary results were obtained for two commercial alloys, UDIMET 700 and Mar-M 247, that were modified by varying the cobalt content. For both alloys the cobalt content was reduced in steps to zero. Nickel content was increased accordingly to make up for the reduced cobalt but all other constituents were held constant. Wedge bar test samples were produced by casting. The hot corrosion test consisted of cyclically exposing samples to the high velocity flow of combustion products from an air-fuel burner fueled with jet A-1 and seeded with a sodium chloride aqueous solution. The flow velocity was Mach 0.5 and the sodium level was maintained at 0.5 ppm in terms of fuel plus air. The test cycle consisted of holding the test samples at 900 C for 1 hour followed by 3 minutes in which the sample could cool to room temperature in an ambient temperature air stream.

  11. 75 FR 9210 - Wireless Telecommunications Bureau Seeks Comment on Petition for Rulemaking Regarding 700 MHz...

    Science.gov (United States)

    2010-03-01

    [email protected] or call the Consumer & Governmental Affairs Bureau at 202-418-0530 (Voice), 202-418-0432 (TTY... the Commission to ``assure that consumers will have access to all paired 700 MHz spectrum that the Commission licenses, to act so that the entire 700 MHz band will develop in a competitive fashion, and to...

  12. 75 FR 6865 - Airworthiness Directives; The Boeing Company Model 737-700 (IGW) Series Airplanes Equipped With...

    Science.gov (United States)

    2010-02-12

    ... replacing aging float level switch conduit assemblies, periodically inspecting the external dry bay system... Model 737-700 (IGW) Series Airplanes Equipped With Auxiliary Fuel Tanks Installed in Accordance With... airworthiness directive (AD) for certain Model 737-700 (IGW) series airplanes. This proposed AD would require...

  13. 25 CFR 700.277 - Requests for access to records: Submission.

    Science.gov (United States)

    2010-04-01

    ..., both on the envelope and on the face of the request, with the legend “PRIVACY ACT REQUEST FOR ACCESS... further notified that under § 700.279(d) the failure to state willingness to pay fees as high as are...

  14. 76 FR 62309 - Implementing a Nationwide, Broadband, Interoperable Public Safety Network in the 700 MHz Band

    Science.gov (United States)

    2011-10-07

    ... the 700 MHz Band AGENCY: Federal Communications Commission. ACTION: Final rule. SUMMARY: In this... spectrum of the 700 MHz band. The Commission dismissed the request, but clarified that a reasonably broad... personnel including, but not limited to, activities of police, fire and medical emergency first responders...

  15. 30 CFR 71.700 - Inhalation hazards; threshold limit values for gases, dust, fumes, mists, and vapors.

    Science.gov (United States)

    2010-07-01

    ... gases, dust, fumes, mists, and vapors. 71.700 Section 71.700 Mineral Resources MINE SAFETY AND HEALTH... limit values for gases, dust, fumes, mists, and vapors. (a) No operator of an underground coal mine and... limit values adopted by the American Conference of Governmental Industrial Hygienists in “Threshold...

  16. Welding thermal cycle-triggered precipitation processes in steel S700MC subjected to the thermo-mechanical control processing

    OpenAIRE

    Górka J.

    2017-01-01

    This study presents tests concerned with welding thermal process-induced precipitation processes taking place in 10 mm thick steel S700MC subjected to the Thermo-Mechanical Control Process (TMCP) with accelerated cooling. The thermomechanical processing of steel S700MC leads to its refinement, structural defects and solutioning with hardening constituents. Tests of thin foils performed using a transmission electron microscope revealed that the hardening of steel S700MC was primarily caused by...

  17. Earliest floral grave lining from 13,700-11,700-y-old Natufian burials at Raqefet Cave, Mt. Carmel, Israel.

    Science.gov (United States)

    Nadel, Dani; Danin, Avinoam; Power, Robert C; Rosen, Arlene M; Bocquentin, Fanny; Tsatskin, Alexander; Rosenberg, Danny; Yeshurun, Reuven; Weissbrod, Lior; Rebollo, Noemi R; Barzilai, Omry; Boaretto, Elisabetta

    2013-07-16

    Flowering plants possess mechanisms that stimulate positive emotional and social responses in humans. It is difficult to establish when people started to use flowers in public and ceremonial events because of the scarcity of relevant evidence in the archaeological record. We report on uniquely preserved 13,700-11,700-y-old grave linings made of flowers, suggesting that such use began much earlier than previously thought. The only potentially older instance is the questionable use of flowers in the Shanidar IV Neanderthal grave. The earliest cemeteries (ca. 15,000-11,500 y ago) in the Levant are known from Natufian sites in northern Israel, where dozens of burials reflect a wide range of inhumation practices. The newly discovered flower linings were found in four Natufian graves at the burial site of Raqefet Cave, Mt. Carmel, Israel. Large identified plant impressions in the graves include stems of sage and other Lamiaceae (Labiatae; mint family) or Scrophulariaceae (figwort family) species; accompanied by a plethora of phytoliths, they provide the earliest direct evidence now known for such preparation and decoration of graves. Some of the plant species attest to spring burials with a strong emphasis on colorful and aromatic flowers. Cave floor chiseling to accommodate the desired grave location and depth is also evident at the site. Thus, grave preparation was a sophisticated planned process, embedded with social and spiritual meanings reflecting a complex preagricultural society undergoing profound changes at the end of the Pleistocene.

  18. 28 CFR 700.31 - Exemption of the Office of Independent Counsel's systems of records-limited access.

    Science.gov (United States)

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Exemption of the Office of Independent Counsel's systems of records-limited access. 700.31 Section 700.31 Judicial Administration OFFICE OF INDEPENDENT COUNSEL PRODUCTION OR DISCLOSURE OF MATERIAL OR INFORMATION OF THE OFFICE OF INDEPENDENT COUNSEL Exemption of the Office of Independent...

  19. The effect of heat treatment on the micro-structure and the mechanical properties of high-temperature nickel-base-superalloys

    International Nuclear Information System (INIS)

    Schubert, R.; Horn, E.

    1974-01-01

    General review of heat treatment applied to high-temperature nickel-base-superalloys as a function of the volume percent of the γ'-phase. Heat treatment schedule. γ'-morphology and γ'-distribution as well as their effect on mechanical properties. Values obtained from tensile tests up to 1,000 0 C. Results obtained from creep tests. Limitation for the heat treatment of alloys having an unstable γ'-phase. Alloys X 5 NiCrTi 26 15, ATS 270 (approximately INCO 718), NiCr 20 TiAl, NiCr 20 Co 18 Ti, ATS 342 (approximately Waspaloy), ATS 354 (approximately Udimet 520), NiCo 20 Cr 15 MoAlTi, ATS 382 (approximately Udimet 710), ATS 381-G (approximately Mar M 246), FIS 145 and ATS 391-G (aproximately IN 100). (orig.) [de

  20. 7 CFR 57.700 - Prohibition on disposition of restricted eggs.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Prohibition on disposition of restricted eggs. 57.700... AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946 AND THE EGG PRODUCTS INSPECTION ACT (CONTINUED) INSPECTION OF EGGS (EGG PRODUCTS INSPECTION ACT) Regulations Governing the Inspection of Eggs...

  1. Phase equilibria in the Ni–Al–Ga system at 700 °C

    International Nuclear Information System (INIS)

    Belyavina, N.; Markiv, V.; Nakonechna, O.; Lozovyi, F.

    2014-01-01

    Graphical abstract: - Highlights: • We study phase equilibria in ternary Ni–Al–Ga in the whole concentration range. • Ni(Al,Ga), Ni 2 (Al,Ga) 3 , Ni 5 (Al,Ga) 3 extended solid solutions exist in this system. • Isothermal section (700 °C) of the Ni–Al–Ga system has been constructed. • Small additions of Ga increase compressive strength of Ni 3 (Al,Ga) solid solution. - Abstract: Phase relations in the ternary Ni–Al–Ga system at 700 °C have been established by the X-ray powder diffraction methods. In addition to already known Ni 3 (Al,Ga) continuous solid solution, Ni(Al,Ga) continuous solid solution as well as Ni 2 (Al,Ga) 3 and Ni 5 (Al,Ga) 3 extended solid solutions were found to exist in this system. It was shown that the ternary Ni 2 (Al,Ga) 3 and Ni 5 (Al,Ga) 3 compounds do not belong to the continuous solid solutions because of two-phase gaps on the Ni 2 Al 3 –Ni 2 Ga 3 (∼30–50 at.% Ga) and Ni 5 Al 3 –Ni 5 Ga 3 (∼12–25 at.% Ga) isolines at 700 °C. Some crystal structure peculiarities such as atomic ordering–disordering and presence of structural vacancies have been revealed for all solid solutions existing in the Ni–Al–Ga system. It was found that the compressive strength of the Ni 3 (Al,Ga) solid solution increases with small additions of gallium (about 2.5 at.%). The isothermal section (700 °C) of the ternary Ni–Al–Ga system including four extended solid solutions (Ni 3 (Al,Ga), Ni 5 (Al,Ga) 3 , Ni(Al,Ga) and Ni 2 (Al,Ga) 3 ) has been constructed and plotted

  2. 30 CFR 285.700 - What reports must I submit to MMS before installing facilities described in my approved SAP, COP...

    Science.gov (United States)

    2010-07-01

    ... installing facilities described in my approved SAP, COP, or GAP? 285.700 Section 285.700 Mineral Resources... § 285.700 What reports must I submit to MMS before installing facilities described in my approved SAP... in your approved COP (§ 285.632(a)) and, when required by this part, your SAP (§ 285.614(b)) or GAP...

  3. Easy French phrase book over 700 phrases for everyday use

    CERN Document Server

    McCoy, Heather

    2012-01-01

    Over 700 French phrases and sentences include terms for modern telecommunications, idioms, and slang. Designed as a quick reference and study guide, this up-to-date volume is organized for quick access to phrases related to greetings, transportation, shopping, emergencies, and other common circumstances. A phonetic pronunciation accompanies each phrase.

  4. 32 CFR 700.822 - Delivery of personnel to civil authorities and service of subpoena or other process.

    Science.gov (United States)

    2010-07-01

    ... service of subpoena or other process. 700.822 Section 700.822 National Defense Department of Defense... personnel to civil authorities and service of subpoena or other process. (a) Commanding officers or other... service of subpoenas or other process as provided by the Manual of the Judge Advocate General. ...

  5. Reading the New Standard ISA700

    Directory of Open Access Journals (Sweden)

    Daniel Botez

    2010-12-01

    Full Text Available Review of permanent professional standards is a requirement for professional bodies of professional accountants, resulting in broader processes of globalization and harmonization. A set of revised standards on financial audit engagement was published by IFAC in April 2009. International Standard on Auditing (ISA 700 "Forming an opinion and reporting on financial statements” is one of them. This standard deals with the auditor's responsibility to form an opinion on the financial statements and determine the form and content of the auditor's report issued following an audit of financial statements. Even if you do not have major changes, the revised standard contains several provisions that emphasize the important role of the auditor's report and more specifically defines its responsibility.

  6. 75 FR 9586 - Solicitation of Participation In and Public Meeting to Discuss Public Safety 700 MHz Broadband...

    Science.gov (United States)

    2010-03-03

    ... to local, state and tribal public safety agencies (i.e. fire, police, emergency medical services...\\ Implementing a Nationwide, Broadband, Interoperable Public Safety Network in the 700 MHz Band, FCC WT Docket No... technology deployed in the 700 MHz bands, specific to the needs of public safety agencies. NIST has developed...

  7. The thrombospondin-1 N700S polymorphism is associated with early myocardial infarction without altering von Willebrand factor multimer size.

    Science.gov (United States)

    Zwicker, Jeffrey I; Peyvandi, Flora; Palla, Roberta; Lombardi, Rossana; Canciani, Maria Teresa; Cairo, Andrea; Ardissino, Diego; Bernardinelli, Luisa; Bauer, Kenneth A; Lawler, Jack; Mannucci, Pier

    2006-08-15

    The N700S polymorphism of thrombospondin-1 (TSP-1) has been identified as a potential genetic risk factor for myocardial infarction (MI). In a large case-control study of 1425 individuals who survived a myocardial infarction prior to age 45, the N700S polymorphism was a significant risk factor for myocardial infarction in both homozygous (odds ratio [OR] 1.9, 95% confidence interval [CI] 1.1-3.3, P = .01) and heterozygous carriers of the S700 allele (OR 1.4, 95% CI 1.1-3.3, P = .01). TSP-1 has been shown to reduce von Willebrand factor (VWF) multimer size, and the domain responsible for VWF-reducing activity has been localized to the calcium-binding C-terminal sequence. As the N700S polymorphism was previously shown to alter the function of this domain, we investigated whether the altered VWF-reducing activity of TSP-1 underlies the observed prothrombotic phenotype. The TSP1 N700S polymorphism did not influence VWF multimer size in patients homozygous for either allele nor was there a significant reduction of VWF multimer size following incubation with recombinant N700S fragments or platelet-derived TSP-1.

  8. The political economy of churches in Denmark over 700 years

    DEFF Research Database (Denmark)

    Paldam, Ella; Paldam, Martin

    This paper reports new macro time-series for the number and size of churches in Denmark from year 1300 to 2000. Church densities are defined as the series per capita. The densities are interpreted as a proxy for religiosity. It is falling throughout all 700 years, but two events gave an extra fall...

  9. Safety margin improvement by adopting the feature of interleaving in 700 MWe PHWR

    International Nuclear Information System (INIS)

    Kumar, Nrependra; Yadav, S.K.; Khan, T.A.; Dixit, A.; Singhal, Mukesh; Nair, Suma R.

    2015-01-01

    Indian Pressurised Heavy Water Reactors (IPHWRs) of 700 MWe are under construction at Kakrapar Atomic Power Project -3,4 and Rajasthan Atomic Power Project-7,8. These units have enhanced safety features with respect to standard IPHWRs. One of the enhanced features is interleaving of feeders/channels. In interleaved feeder configuration, each header located at either end of reactor gets connected to one quarter of core channels, which are uniformly distributed. The core is divided into two loops with feeder connected in interleaved fashioned. In this paper a comparative study has been performed between the two cases: 1) The core splits in two vertical halves and each vertical half is a loop of PHT (TAPS-3 and 4 Type configuration). 2) The core is divided into two loops with feeders/ channels connected in interleaved fashioned (700 MWe Configuration). LOCA studies have been performed for 700 MWe PHWR considering interleaving of feeders configuration using in-house developed computer code ATMIKA and 3-D neutron kinetics code IQS-3D. The issue of interleaving is closely linked to an inherent reactivity characteristic of PHWR reactors (viz., positive void reactivity coefficient) which leads to a power increase following a Large LOCA. In 700 MWe PHWR with intent to improve the safety margin, adopted the feature of interleaving of feeders which causes in reduction in the magnitude of void coefficient and results in reduction of peak power during LBLOCA. The systematic LBLOCA study demonstrates that interleaved configuration of feeder/channels of two loops has higher safety margins (i.e. with respect to peak power, prompt-criticality margin, adiabatic heat deposition on the fuel pins, sheath temperature excursion and clad oxidation) with regard to the effectiveness of shutdown system. (author)

  10. Flux mapping algorithm (FMA) for 700 MWe PHWR

    International Nuclear Information System (INIS)

    Sonavani, Manoj; Ingle, V.J.; Singhvi, P.K.; Raj, Manish; Fernando, M.P.S.; Kumar, A.N.

    2012-01-01

    For large reactor like 700 MWe PHWR effective spatial control is essential and is provided by RRS. For spatial control purpose reactor core is divided into 14 power zones. Corresponding to each zone is a light water zonal compartment. The 14 ZCCs are located in two radial planes, each containing 7 ZCCs. For each zone, power measurement is carried out using inconel (3 pitch long) self powered neutron detector (SPND) at appropriate location close to the respective ZCC. Since the zone power as obtained by the healthy zone control detector (ZCD) reading belonging to a particular zone may not correspond to its actual power because the detector per zone, measure only average fluxes but the zone extends over a large core region. Therefore accurate estimation of zone power calibration factors is required to estimate the zone powers and also to provide effective spatial power control to avoid the xenon induced spatial power oscillations in large PHWRs like 700 and 540 MWe Reactors. This accurate calculation of zone power is carried out by FMS which uses λ modes in its algorithm. Flux at any point inside the reactor can be represented in terms of the linear combination of these modes. Coefficients used in the expansion are called combining coefficient. If the readings of the detectors are known, then combining coefficients can be estimated by simple matrix operations. Once these combining coefficients are known, flux at any point inside the reactor can be found. (author)

  11. 15 CFR 700.16 - Changes or cancellations of priority ratings and rated orders.

    Science.gov (United States)

    2010-01-01

    ... Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS DEFENSE PRIORITIES AND ALLOCATIONS SYSTEM Industrial Priorities § 700...

  12. 17 CFR 247.700 - Defined terms relating to the networking exception from the definition of “broker.”

    Science.gov (United States)

    2010-04-01

    ... the average of the minimum and maximum hourly wage established by the bank for the current or prior... networking exception from the definition of âbroker.â 247.700 Section 247.700 Commodity and Securities Exchanges SECURITIES AND EXCHANGE COMMISSION (CONTINUED) REGULATION R-EXEMPTIONS AND DEFINITIONS RELATED TO...

  13. Modeling of SOC-700 Hyperspectral Imagery with the CAMEO-SIM Code

    Science.gov (United States)

    2007-10-26

    Yannick, 2001, “SOC-700 and HS-Analysis 2 User’s Manual”, Surface Optics, San Diego [2] Cohen, Michael F. and Wallace, John R., 1993, “ Radiosity ...and Realistic Image Synthesis”, Academic Press, San Francisco [3] Sillion, Francois X. and Puech, Claude, 1994, “ Radiosity and Global Illumination

  14. 32 CFR 700.406 - Naval Vessel Register, classification of naval craft, and status of ships and service craft.

    Science.gov (United States)

    2010-07-01

    ... craft, and status of ships and service craft. 700.406 Section 700.406 National Defense Department of... Register, classification of naval craft, and status of ships and service craft. (a) The Chief of Naval... craft and the designation of status for each ship and service craft. (b) Commissioned vessels and craft...

  15. 20 CFR 668.700 - What process must an INA grantee use to plan its employment and training services?

    Science.gov (United States)

    2010-04-01

    ... it uses to plan other activities and services. (b) However, in the process of preparing its Two Year... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false What process must an INA grantee use to plan its employment and training services? 668.700 Section 668.700 Employees' Benefits EMPLOYMENT AND...

  16. 12 CFR 218.700 - Defined terms relating to the networking exception from the definition of “broker.”

    Science.gov (United States)

    2010-01-01

    ... the average of the minimum and maximum hourly wage established by the bank for the current or prior... exception from the definition of âbroker.â 218.700 Section 218.700 Banks and Banking FEDERAL RESERVE SYSTEM BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM EXCEPTIONS FOR BANKS FROM THE DEFINITION OF BROKER IN...

  17. Rapid emergence of life shown by discovery of 3,700-million-year-old microbial structures

    Science.gov (United States)

    Nutman, Allen P.; Bennett, Vickie C.; Friend, Clark R. L.; van Kranendonk, Martin J.; Chivas, Allan R.

    2016-09-01

    Biological activity is a major factor in Earth’s chemical cycles, including facilitating CO2 sequestration and providing climate feedbacks. Thus a key question in Earth’s evolution is when did life arise and impact hydrosphere-atmosphere-lithosphere chemical cycles? Until now, evidence for the oldest life on Earth focused on debated stable isotopic signatures of 3,800-3,700 million year (Myr)-old metamorphosed sedimentary rocks and minerals from the Isua supracrustal belt (ISB), southwest Greenland. Here we report evidence for ancient life from a newly exposed outcrop of 3,700-Myr-old metacarbonate rocks in the ISB that contain 1-4-cm-high stromatolites—macroscopically layered structures produced by microbial communities. The ISB stromatolites grew in a shallow marine environment, as indicated by seawater-like rare-earth element plus yttrium trace element signatures of the metacarbonates, and by interlayered detrital sedimentary rocks with cross-lamination and storm-wave generated breccias. The ISB stromatolites predate by 220 Myr the previous most convincing and generally accepted multidisciplinary evidence for oldest life remains in the 3,480-Myr-old Dresser Formation of the Pilbara Craton, Australia. The presence of the ISB stromatolites demonstrates the establishment of shallow marine carbonate production with biotic CO2 sequestration by 3,700 million years ago (Ma), near the start of Earth’s sedimentary record. A sophistication of life by 3,700 Ma is in accord with genetic molecular clock studies placing life’s origin in the Hadean eon (>4,000 Ma).

  18. Research and Implementation of Software Used for the Remote Control for VM700T Video Measuring Instrument

    Directory of Open Access Journals (Sweden)

    Song Wenjie

    2015-01-01

    Full Text Available In this paper, the measurement software which can be used to realize remote control of the VM700T video measuring instrument is introduced. The authors can operate VM700T by a virtual panel on the client computer, select the results that the measuring equipment displayed to transmit it, and then display the image on the VM700T virtual panel in real time. The system does have some practical values and play an important role in distance learning. The functions that the system realized mainly includes four aspects: the real-time transmission of message based on the socket technology, the serial connection between server PC and VM700T measuring equipment, the image acquisition based on VFW technology and JPEG compression and decompression, and the network transmission of image files. The actual network transmission test is shown that the data acquisition method of this thesis is flexible and convenient, and the system is of extraordinary stability. It can display the measurement results in real time and basically realize the requirements of remote control. In the content, this paper includes a summary of principle, the detailed introduction of the system realization process and some related technology.

  19. Fractography analysis of Inconel 718 fatigued at 700°C

    Directory of Open Access Journals (Sweden)

    Michal Jambor

    2016-12-01

    Full Text Available This work deals with the fractography analysis of nickel-base superalloy Inconel 718 fatigued at 700°C in air atmosphere in the high cycle region. During cyclic loading of this alloy at high temperatures some different mechanisms compared to cyclic loading at ambient temperature take place. Cyclic plastic deformation at high temperatures causes some structural changes, which could have some influence on the fatigue process.

  20. Component behaviour in the 700 C power plant. Numerical and experimental investigations; Komponentenverhalten im 700 C-Kraftwerk. Numerische und experimentelle Untersuchungen

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, Kay H.

    2013-07-19

    Currently martensitic steels are used in fossil fired power plants with maximum working temperatures up to 625 C. These steels do not show the required creep rupture strength at the target temperature of 700 C. For these high temperatures, new materials like the nickel base alloys have to be qualified for power plants services. Originating from the weld of turbine materials, nickel base alloys show outstanding creep rupture strength. An alloy with good prospects out of the material class of the nickel base alloys is Alloy 617 mod. However, this material is expensive due to its high nickel content. Furthermore, the complex machinability of this material leads to an additional increase in expenses. A complete fabrication of the boiler area using Alloy 617 mod is not economically feasible, which means that the usage of this material has to be limited to the temperature weld of 625 C to 700 C. For the boiler area with temperatures below 625 C the well proven 9 % to 12 % Cr-steels, like T/P92 and VM12/VM12-SHC may be used. In the weld of low temperatures up to 525 C the usage of the 2.5 % Cr-steel T/P24 offers numerous advantages, in particular in the fabrication of membrane walls. This material shows good creep properties up to temperatures of 525 C and, for thin walled components, T24 can be welded without post weld heat treatment by using suitable techniques. For a successful design and fabrication of a 700 C fossil fired power plant, appropriate materials have to be qualified. Here, a special focus is set on the creep properties of these materials. The presented work is a significant contribution to the qualification of these materials. First, the materials Alloy 617 mod, T/P92, VM12/VM12-SHC and T24 are briefly introduced and characterized. After this, the materials are investigated in a detailed creep testing program. This program includes investigations on base material, extracted from tubes, pipes and inductive bends of pipes. In addition, crossweld specimens

  1. 32 CFR 700.323 - The Assistant Secretary of the Navy (Financial Management).

    Science.gov (United States)

    2010-07-01

    ... Assistants § 700.323 The Assistant Secretary of the Navy (Financial Management). The Assistant Secretary of the Navy (Financial Management) is the Comptroller of the Navy, and is responsible for all matters related to the financial management of the Department of the Navy, including: (a) Budgeting; (b...

  2. 25 CFR 700.841 - Determination of loss or absence of archaeological interest.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Determination of loss or absence of archaeological... OPERATIONS AND RELOCATION PROCEDURES New Lands Grazing § 700.841 Determination of loss or absence of... providing scientific or humanistic understandings of past human behavior, cultural adaptation, and related...

  3. 21 CFR 700.27 - Use of prohibited cattle materials in cosmetic products.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Use of prohibited cattle materials in cosmetic... SERVICES (CONTINUED) COSMETICS GENERAL Requirements for Specific Cosmetic Products § 700.27 Use of prohibited cattle materials in cosmetic products. (a) Definitions. The definitions and interpretations of...

  4. 25 CFR 700.157 - Actual reasonable moving and related expenses-nonresidential moves.

    Science.gov (United States)

    2010-04-01

    ... of § 700.151(c) a certified eligible business, farm operation or nonprofit organization is entitled...-moves his business, farm operation, or nonprofit organization, the Commission may approve a payment for... and modifications necessary to adapt such property to the replacement structure or to the utilities or...

  5. Development of a PF fired high efficiency power plant (AD700)

    Energy Technology Data Exchange (ETDEWEB)

    Blum, R.; Kjaer, S.; Bugge, J. [DONG Energy Generation, Fredericia (Denmark)

    2007-05-15

    European efforts to start substantial improvements of the performance of well established supercritical coal-fired power technology named the AD700 project began in 1998. Major targets were development of austenitic materials and nickel-based superalloys for the hottest sections of boilers, steam lines and turbines. Other targets were development of boiler and turbine designs for the more advanced conditions and finally economic viability of the AD700 technology has been investigated. The project has been very successful and 40 partners from the European power industry have worked together in several projects co-funded by the European Commission for nearly years. Procurement of mature and commercially optimised AD700 plant could take place around 2015. The investigated nickel-based materials have shown very high creep strengths but they have also shown to be very hard to manufacture, and more efforts to define new machining lines are being started. Ongoing tests indicate that the developed austenitic material will fulfil its creep strength target and is now ready for commercialisation. Development works on boiler and turbine designs for the advanced steam conditions have also been successfully completed but they also clearly indicate that further development work on improved ferritic steel for furnace walls is important. Conventional development of the steam cycles is based on new improved materials, which open for higher steam temperatures and efficiencies whereas other thermodynamic tools are only slowly being accepted. However, in the present paper a proposal for steam cycle improvements not based on higher steam temperatures is presented. The improved cycle is named the Master Cycle (MC) and it is based on a revision of the double reheat steam cycle where the bleeds of the IP turbines have been moved to a feed pump turbine bleeding on the first cold reheat line. Elsam has established protection of a patent for the MC in a number of countries. At constant main

  6. Nitrogen implantation into silicon at 700-1100 deg C

    International Nuclear Information System (INIS)

    Kachurin, G.A.; Tyschenko, I.E.; Popov, V.P.; Tijs, S.A.; Plotnikov, A.E.

    1989-01-01

    Nitrogen ions 130-140 kW potential accelerated were implanted in silicon heated up to Ti=700-1100 deg C. Densities of ion current were 1-5 mcA/cm 2 , doses did not exceed 5x10 17 cm -2 . Initial stages of nitride formation in buried layers are investigated by means of Rutherford backscattering, layer-by-layer Augerspctroscopy and electron microscopy. It is determind, that Ti growth from 700 up to 900 deg C is accompanied by essential reduction of defectiveness of silicon near-the-surface layer at nitrogen retention within the limits of the calculation profile of ion ranges. At Ti=900 deg C nitrogen is rather mobile and at ∼5x10 16 cm -2 dose it is drown to α-Si 3 N 4 crystalling extraction in R p range. Beginning from Ti ≅1000 deg C nitrogen is not retained in the furied layer and diffuses to the surface. No essenstial losses of nitrogen due to evaporation or inside diffusion are observed. It is noted, that critical Ti, when nitrogen is accumulated in the buried layer, correspond to critical temperatures, when light ions introduce essential structure distortions. Conclusion is made, that irradition-introduced distortions of structure represent centres of initiation and growth of nitride phase. At 1150 deg C additional annaling during 3 hs nitrogen, occurring outside the stable extraction, is redistributed between th surface and furied layers, sintering in narrow concentration peaks

  7. Frequency Arrangement For 700 MHz Band

    Directory of Open Access Journals (Sweden)

    Ancans G.

    2015-02-01

    Full Text Available The 694-790 MHz (700 MHz band was allocated by the 2012 World Radiocommunication Conference (WRC-12 in ITU Region 1 (Europe included, to the mobile service on a co-primary basis with other services to which this band was allocated on the primary basis and identified for the International Mobile Telecommunications (IMT. At the same time, the countries of Region 1 will be able also to continue using these frequencies for their broadcasting services if necessary. This allocation will be effective immediately after 2015 World Radiocommunication Conference (WRC-15. In order to make the best possible use of this frequency band for mobile service, a worldwide harmonized frequency arrangement is to be prepared to allow for large economies of scale and international roaming as well as utilizing the available spectrum in the best possible way, minimizing possible interference between services, facilitating deployment and cross-border coordination. The authors analyze different possible frequency arrangements and conclude on the frequency arrangement most suitable for Europe.

  8. T700 power turbine rotor multiplane/multispeed balancing demonstration

    Science.gov (United States)

    Burgess, G.; Rio, R.

    1979-01-01

    Research was conducted to demonstrate the ability of influence coefficient based multispeed balancing to control rotor vibration through bending criticals. Rotor dynamic analyses were conducted of the General Electric T700 power turbine rotor. The information was used to generate expected rotor behavior for optimal considerations in designing a balance rig and a balance technique. The rotor was successfully balanced 9500 rpm. Uncontrollable coupling behavior prevented observations through the 16,000 rpm service speed. The balance technique is practical and with additional refinement it can meet production standards.

  9. Savannah River Plant engineering and design history. Volume 4: 300/700 Areas & general services and facilities

    Energy Technology Data Exchange (ETDEWEB)

    1957-01-01

    The primary function of the 300 Area is the production and preparation of the fuel and target elements required for the 100 Area production reactors. Uranium slugs and lithium-aluminium alloy control and blanket rods are prepared in separate structures. Other facilities include a test pile, a physics assembly laboratory, an office and change house, an electrical substation, and various service facilities such as rail lines, roads, sewers, steam and water distribution lines, etc. The 700 Area contains housing and facilities for plant management, general plant services, and certain technical activities. The technical buildings include the Main Technical Laboratory, the Waste Concentration Building, the Health Physics Headquarters, and the Health Physics Calibration building. Sections of this report describe the following: development of the 300-M Area; selection and description of process; design of main facilities of the 300 Area; development of the 700-A Area; design of the main facilities of the 700 Area; and general services and facilities, including transportation, plant protection, waste disposal and drainage, site work, pilot plants, storage, and furniture and fixtures.

  10. Study on microstructure of transition zone and its strong contrast of single T700 carbon fibers

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Xinshuang; Zhang, Kexiang [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Fan, Zhen; Feng, Zhihai [National Key Laboratory of Advanced Functional Composite Materials, Aerospace Research Institute of Materials and Processing Technology, Beijing 100076 (China); He, LianLong, E-mail: llhe@imr.ac.cn [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China)

    2017-06-01

    Highlights: • The transition zone of T700 carbon fiber was first identified with higher density in addition to higher orientation. • The higher sample density still existed while the higher orientation disappeared after heat treatment at 2800 °C. • The strong contrast of the transition zone mainly results from its higher density. • The transition zone with higher density and orientation may exist not only in the T700 but other PAN-based carbon fibers. - Abstract: The transition zone (TZ) between the skin and core of Toray T700 carbon fiber was investigated by transmission electron microscopy. The higher basal-plane orientation was identified in the TZ compared with the skin and core, but it disappeared after heat treatment at 2800 °C. Plasmon peak energy in the TZ was higher than that in the skin and core about 0.7–0.8 eV, indicating the TZ with higher density. No element concentration existed in the TZ. The TZ with strong contrast manifests itself before and after heat treatment, and formation mechanism of its strong contrast was proposed.

  11. Dynamic life-time assessing method for the N1C700 turbine's rotor

    International Nuclear Information System (INIS)

    Popescu-Vifor, B.

    1993-01-01

    The N1C700 turbine's rotor subject to different sorts of stress variations was investigated through dynamic life-time assessing method. To obtain the temperature fields at different steam parameters inside the turbine components, a computer code named DENOPAR was developed

  12. Studies on flow induced vibration of reactivity devices of 700 MWe Indian PHWR

    Energy Technology Data Exchange (ETDEWEB)

    Prabhakaran, K.M., E-mail: kmprabha@yahoo.com [Reactor Safety Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Goyal, P.; Dutta, Anu; Bhasin, V.; Vaze, K.K.; Ghosh, A.K. [Reactor Safety Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Pillai, Ajith V.; Mathew, Jimmy [Nuclear Power Corporation of India Ltd., Mumbai 400 094 (India)

    2012-03-15

    Highlights: Black-Right-Pointing-Pointer FIV studies on internals of heavy water filled calandria of 700 MWe Indian PHWR is presented. Black-Right-Pointing-Pointer This includes CFD and structural dynamic analysis to predict the dynamic behavior of component lying inside calandria. Black-Right-Pointing-Pointer Results of these calculations as well as conclusions from this investigation are presented. Black-Right-Pointing-Pointer It is established that FIV is not a concern in the present design of calandria internals. - Abstract: Component failures due to excessive flow-induced vibration are still affecting the performance and reliability of nuclear power stations. Tube failures due to fretting-wear in nuclear steam generators, and vibration related damage of reactor internals are of particular concern. In the Indian nuclear industry, flow induced vibrations are assessed early in the design process and the results are incorporated in the design procedures. In this paper the details of flow induced vibration studies on internals like liquid zone control unit and poison injection units of heavy water filled calandria of 700 MWe Indian pressurized heavy water reactor is given. This includes computational fluid dynamics studies from which the velocities are extracted for the components lying inside the calandria. With these velocities as input, further studies are performed to predict the dynamic behavior of these components. Results of these calculations as well as conclusions derived from this investigation are presented. Based on the studies it has been established that flow induced vibration is not a concern in the present design of 700 MWe calandria internals.

  13. Polymorphisms A387P in thrombospondin-4 and N700S in thrombospondin-1 perturb calcium binding sites.

    Science.gov (United States)

    Stenina, Olga I; Ustinov, Valentin; Krukovets, Irene; Marinic, Tina; Topol, Eric J; Plow, Edward F

    2005-11-01

    Recent genetic studies have associated members of the thrombospondin (TSP) gene family with premature cardiovascular disease. The disease-associated polymorphisms lead to single amino acid changes in TSP-4 (A387P) and TSP-1 (N700S). These substitutions reside in adjacent domains of these highly homologous proteins. Secondary structural predictive programs and the homology of the domains harboring these amino acid substitutions to those in other proteins pointed to potential alterations of putative Ca2+ binding sites that reside in close proximity to the polymorphic amino acids. Since Ca2+ binding is critical for the structure and function of TSP family members, direct evidence for differences in Ca2+ binding by the polymorphic forms was sought. Using synthetic peptides and purified recombinant variant fragments bearing the amino acid substitutions, we measured differences in Tb3+ luminescence as an index of Ca2+ binding. The Tb3+ binding constants placed the TSP-1 region affected by N700S polymorphism among other high-affinity Ca2+ binding sites. The affinity of Ca2+ binding was lower for peptides (3.5-fold) and recombinant fragments (10-fold) containing the S700 vs. the N700 form. In TSP-4, the P387 form acquired an additional Ca2+ binding site absent in the A387 form. The results of our study suggest that both substitutions (A387P in TSP-4 and N700S in TSP-1) alter Ca2+ binding properties. Since these substitutions exert the opposite effects on Ca2+ binding, a decrease in TSP-1 and an increase in TSP-4, the two TSP variants are likely to influence cardiovascular functions in distinct but yet pathogenic ways.

  14. 41 CFR 101-8.700 - Purpose of the Age Discrimination Act of 1975.

    Science.gov (United States)

    2010-07-01

    ... Management Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS GENERAL 8-NONDISCRIMINATION IN PROGRAMS RECEIVING FEDERAL FINANCIAL ASSISTANCE 8.7-Discrimination Prohibited on the Basis of Age § 101-8.700 Purpose... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Purpose of the Age...

  15. Implantation of AMS 700 LGX penile prosthesis preserves penile length without the need for penile lengthening procedures

    Directory of Open Access Journals (Sweden)

    Carlo Luigi Augusto Negro

    2016-01-01

    Full Text Available Implantation of an inflatable penile prosthesis (IPP is a well-established definitive solution for erectile dysfunction when conservative treatments fail. Penile implants may shorten the penis. The AMS 700 LGX IPP is in common use but reports on its mechanical reliability, medium-term postsurgical patient satisfaction, and mean penile length preservation are lacking. We investigate the mean penile length, mechanical reliability, and patient satisfaction at 6 and 12 months after implantation of the AMS 700 LGX. This prospective study consecutively enrolled men undergoing first-time IPP implant surgery from February 2009 to April 2012. Stretched flaccid penile length, penile length at 50% and 100% of stiffness (P50 and P100 and International Index of Erectile Function (IIEF and Erectile Dysfunction Inventory of Treatment Satisfaction (EDITS scores, were measured at 6 and 12 months postsurgery. Of 45 patients who underwent AMS 700 LGX implantation (median age 61 years and completed 6 months′ follow-up, 36 (80% completed the study. A significant difference in stretched flaccid penile length was seen between 6 and 12 months (P = 0.033. P100 was also significantly increased at 6 and 12 months, with a mean 10% increase (1.3 ± 0.4 cm from baseline to 12 months. Differences in mean IIEF scores at 6 and 12 months were significant for the desired domain (P = 0.0001 and for overall satisfaction (P = 0.002; however, mean EDITS scores at 6 and 12 months were not significantly improved. AMS 700 LGX is a powerful tool for preserving penile length in men undergoing penile prosthesis implantation.

  16. New Configuration of Handset MIMO Antenna for LTE 700 Band Applications

    Directory of Open Access Journals (Sweden)

    Byeonggwi Mun

    2013-01-01

    Full Text Available A compact handset multiple-input multiple-output (MIMO antenna for long-term evolution (LTE 700 band (746~787 MHz applications is proposed. The proposed antenna consists of two symmetrical PIFAs. Without the usage of any additional coupling elements between closely mounted antennas, a high isolation (>15 dB and a low enveloped correlation coefficient (ECC<0.35 are achieved by the optimum location and arrangement of MIMO antenna elements.

  17. 21 CFR 700.18 - Use of chloroform as an ingredient in cosmetic products.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Use of chloroform as an ingredient in cosmetic... SERVICES (CONTINUED) COSMETICS GENERAL Requirements for Specific Cosmetic Products § 700.18 Use of chloroform as an ingredient in cosmetic products. (a) Chloroform has been used as an ingredient in cosmetic...

  18. Activatable Optical Imaging with a Silica-Rhodamine Based Near Infrared (SiR700) Fluorophore: A comparison with cyanine based dyes

    Science.gov (United States)

    McCann, Thomas E.; Kosaka, Nobuyuki; Koide, Yuichiro; Mitsunaga, Makoto; Choyke, Peter L.; Nagano, Tetsuo; Urano, Yasuteru; Kobayashi, Hisataka

    2011-01-01

    Optical imaging is emerging as an important tool to visualize tumors. However, there are many potential choices among the available fluorophores. Optical imaging probes that emit in the visible range can image superficial tumors with high quantum yields, however, if deeper imaging is needed then near infrared (NIR) fluorophores are necessary. Most commercially available NIR fluorophores are cyanine based and are prone to non-specific binding and relatively limited photostability. Silica-containing rhodamine (SiR) fluorophores represent a new class of NIR fluorophores, which permit photoactivation via H-dimer formation as well as demonstrate improved photostability. This permits higher tumor-to-background ratios (TBRs) to be achieved over longer periods of time. Here, we compared an avidin conjugated with SiR700 (Av-SiR700) to similar compounds based on cyanine dyes (Av-Cy5.5 and Av-Alexa Fluor 680) in a mouse tumor model of ovarian cancer metastasis. We found that the Av-SiR700 probe demonstrated superior quenching enabling activation after binding-internalization to the target cell. As a result, Av-SiR700 had higher TBRs compared to Av-Cy5.5, and better biostability compared to Av-Alexa Fluor 680. PMID:22034863

  19. 25 CFR 700.335 - Grouping and granting of applications for life estate leases.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Grouping and granting of applications for life estate... OPERATIONS AND RELOCATION PROCEDURES Life Estate Leases § 700.335 Grouping and granting of applications for... least 50% (fifty percent) disabled shall be ranked in order of their age with the oldest listed first...

  20. The role of cobalt on the creep of Waspaloy

    Science.gov (United States)

    Jarrett, R. N.; Chin, L.; Tien, J. K.

    1984-01-01

    Cobalt was systematically replaced with nickel in Waspaloy (which normally contains 13% Co) to determine the effects of cobalt on the creep behavior of this alloy. Effects of cobalt were found to be minimal on tensile strengths and microstructure. The creep resistance and the stress rupture resistance determined in the range from 704 to 760 C (1300 to 1400 C) were found to decrease as cobalt was removed from the standard alloy at all stresses and temperatures. Roughly a ten-fold drop in rupture life and a corresponding increase in minimum creep rate were found under all test conditions. Both the apparent creep activation energy and the matrix contribution to creep resistance were found to increase with cobalt. These creep effects are attributed to cobalt lowering the stacking fault energy of the alloy matrix. The creep resistance loss due to the removal of cobalt is shown to be restored by slightly increasing the gamma' volume fraction. Results are compared to a previous study on Udimet 700, a higher strength, higher gamma' volume fraction alloy with similar phase chemistry, in which cobalt did not affect creep resistance. An explanation for this difference in behavior based on interparticle spacing and cross-slip is presented.

  1. Deconvolution of ferredoxin, plastocyanin, and P700 transmittance changes in intact leaves with a new type of kinetic LED array spectrophotometer.

    Science.gov (United States)

    Klughammer, Christof; Schreiber, Ulrich

    2016-05-01

    A newly developed compact measuring system for assessment of transmittance changes in the near-infrared spectral region is described; it allows deconvolution of redox changes due to ferredoxin (Fd), P700, and plastocyanin (PC) in intact leaves. In addition, it can also simultaneously measure chlorophyll fluorescence. The major opto-electronic components as well as the principles of data acquisition and signal deconvolution are outlined. Four original pulse-modulated dual-wavelength difference signals are measured (785-840 nm, 810-870 nm, 870-970 nm, and 795-970 nm). Deconvolution is based on specific spectral information presented graphically in the form of 'Differential Model Plots' (DMP) of Fd, P700, and PC that are derived empirically from selective changes of these three components under appropriately chosen physiological conditions. Whereas information on maximal changes of Fd is obtained upon illumination after dark-acclimation, maximal changes of P700 and PC can be readily induced by saturating light pulses in the presence of far-red light. Using the information of DMP and maximal changes, the new measuring system enables on-line deconvolution of Fd, P700, and PC. The performance of the new device is demonstrated by some examples of practical applications, including fast measurements of flash relaxation kinetics and of the Fd, P700, and PC changes paralleling the polyphasic fluorescence rise upon application of a 300-ms pulse of saturating light.

  2. Licensing the ACR-700 in the USA

    International Nuclear Information System (INIS)

    Langman, V.; Ion, R.; Reid, C.; Snell, V.

    2003-01-01

    Atomic Energy of Canada Ltd. (AECL), via its 100% owned US subsidiary AECL Technologies Inc., is performing a pre-application review of the Advanced CANDU Reactor (ACR) with the US Nuclear Regulatory Commission (USNRC). Completion of this pre-application review by mid-2004, is in support of an application to the USNRC for Standard Design Certification that is targeted for the fall of 2004. The intent of the pre-application review is to deal up-front with potential issues associated with the CANDU reactor genealogy of the ACR that are different from the Light Water Reactor (LWR) and Boiling Water Reactor (BWR) regulatory framework in the USA. The focus of the paper will be to describe the pre-application review process currently underway with the NRC staff. In the context of the pre-application review this paper will provide an overview of the licensing approach being used to introduce the ACR-700 to the USA. (author)

  3. Licensing the ACR-700 in the USA

    Energy Technology Data Exchange (ETDEWEB)

    Langman, V.; Ion, R. [Atomic Energy of Canada Limited, Mississauga, Ontario (Canada); Reid, C. [Bechtel Power Corporation, San Fransisco, California (United States); Snell, V. [Atomic Energy of Canada Limited, Mississauga, Ontario (Canada)

    2003-07-01

    Atomic Energy of Canada Ltd. (AECL), via its 100% owned US subsidiary AECL Technologies Inc., is performing a pre-application review of the Advanced CANDU Reactor (ACR) with the US Nuclear Regulatory Commission (USNRC). Completion of this pre-application review by mid-2004, is in support of an application to the USNRC for Standard Design Certification that is targeted for the fall of 2004. The intent of the pre-application review is to deal up-front with potential issues associated with the CANDU reactor genealogy of the ACR that are different from the Light Water Reactor (LWR) and Boiling Water Reactor (BWR) regulatory framework in the USA. The focus of the paper will be to describe the pre-application review process currently underway with the NRC staff. In the context of the pre-application review this paper will provide an overview of the licensing approach being used to introduce the ACR-700 to the USA. (author)

  4. 32 CFR 700.201 - Origin and authority of the Department of the Navy.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 5 2010-07-01 2010-07-01 false Origin and authority of the Department of the... The Department of the Navy § 700.201 Origin and authority of the Department of the Navy. (a) The naval... Executive Departments by the 1947 Act) as military departments within the Department of Defense. (c) The...

  5. Meandered Monopoles for 700 MHz LTE Handsets and Improved MIMO Channel Capacity Performance

    Directory of Open Access Journals (Sweden)

    I. Dioum

    2011-12-01

    Full Text Available In this paper, we present the design and the measurement of MIMO meandered monopole antennas and the computation of their channel capacity performance. The initial proposed handset-system is composed of a meandered monopole operating in the LTE 700 MHz band, connected to a parasitic radiating element for the upper 2.5 GHz LTE band. Two antennas of the same kind are then closely positioned on the same 120x50 mm2 Printed Circuit Board (PCB. A neutralization line connects the two antennas to enhance their port-to-port isolation in the 700 MHz band. The computation of the channel capacity performance in this band is based on propagation simulations performed with the GRIMM model from the CREMANT. Two system-prototypes are evaluated: one with the neutralization line for enhanced port-to-port isolation and a second without the neutralization exhibiting poor antenna-to-antenna isolation. It is demonstrated that the neutralization technique helps in giving a minimum improvement of 12% of the capacity performance of the handset-system, and a maximum improvement 46%, in the chosen environment.

  6. 32 CFR 700.326 - The Assistant Secretary of the Navy (Research, Development and Acquisition).

    Science.gov (United States)

    2010-07-01

    ... Assistants § 700.326 The Assistant Secretary of the Navy (Research, Development and Acquisition). The Assistant Secretary of the Navy (Research, Development and Acquisition) is responsible for: (a) Research... 32 National Defense 5 2010-07-01 2010-07-01 false The Assistant Secretary of the Navy (Research...

  7. Microstructure and mechanical properties of titanium aluminum carbides neutron irradiated at 400–700 °C

    Energy Technology Data Exchange (ETDEWEB)

    Ang, Caen [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Parish, Chad M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Shih, Chunghao [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); General Atomics, San Diego, CA (United States); Silva, Chinthaka [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Katoh, Yutai [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-02-23

    Here, this work reports the first mechanical properties of Ti3AlC2-Ti5Al2C3 materials neutron irradiated at ~400, 630 and 700 °C at a fluence of 2 × 1025 n m-2 (E > 0.1 MeV) or a displacement dose of ~2 dpa. After irradiation at ~400 °C, anisotropic swelling and loss of 90% flexural strength was observed. After irradiation at ~630–700 °C, properties were unchanged. Microcracking and kinking-delamination had occurred during irradiation at ~630–700 °C. Further examination showed no cavities in Ti3AlC2 after irradiation at ~630 °C, and MX and A lamellae were preserved. However, disturbance of (0004) reflections corresponding to M-A layers was observed, and the number density of line/planar defects was ~1023 m-3 of size 5–10 nm. HAADF identified these defects as antisite TiAl atoms. Finally, Ti3AlC2-Ti5Al2C3 shows abrupt dynamic recovery of A-layers from ~630 °C, but a higher temperature appears necessary for full recovery.

  8. Differences in TLD 600 and TLD 700 glow curves derived from distict mixed gamma/neutron field irradiations

    International Nuclear Information System (INIS)

    Cavalieri, Tassio A.; Castro, Vinicius A.; Siqueira, Paulo T.D.

    2013-01-01

    In Neutron Capture Therapy, a thermal neutron beam shall impinge on a specific nuclide, such as 10 B, to promote a nuclear reaction which releases the useful therapeutic energy. A nuclear reactor is usually used as the neutron source, and therefore field contaminants such as gamma and high energy neutrons are also present in the field. However, mixed field dosimetry still stands as a challenge in some cases, due to the difficulty to experimentally discriminate the dose from each field component. For the mixed field dosimetry, the International Commission on Radiation end Units (ICRU) recommends the use of detector pairs with different responses for each beam component. The TLD 600/700 pair meets this need, because these LiF detectors have different Li isotopes concentration, with distinct thermal neutron responses because 6 Li presents a much higher neutron capture cross section than does 7 Li for low energy neutrons. TLD 600 is 6 Li enriched while TLD 700 is 7 Li enriched. However, depending on the neutron spectrum presented in the mixed field, TLD 700 response to thermal neutrons cannot be disregarded. This work aims to study the difference in TLD 600 and TLD 700 glow curves when these TLDs are submitted to mixed fields of different energy spectra and components balance. The TLDs were irradiated in a pure gamma source, and in mixed fields from an AmBe sealed source and from the IPEN/MB-01 reactor. These TLDs were read and had their two main dosimetric regions analyzed to observe the differences in the glow curves of these TLDs in each irradiation. Field components discrimination was achieved through Monte Carlo simulations run with MCNP radiation transport code. (author)

  9. Hemoglobin in samples with leukocytosis can be measured on ABL 700 series blood gas analyzers

    NARCIS (Netherlands)

    Scharnhorst, V.; Laar, van der P.D.; Vader, H.

    2003-01-01

    To compare lactate, bilirubin and Hemoglobin F concentrations obtained on ABL 700 series blood gas analyzers with those from laboratory methods. Pooled neonatal plasma, cord blood and adult plasma samples were used for comparison of bilirubin, hemoglobin F and lactate concentrations respectively.

  10. Conversion of the COBRA-IV-I code from CDC CYBER to HP 9000/700 version

    International Nuclear Information System (INIS)

    Sohn, D. S.; Yoo, Y. J.; Nahm, K. Y.; Hwang, D. H.

    1996-01-01

    COBRA-IV-I is a multichannel analysis code for the thermal-hydraulic analysis of rod bundle nuclear fuel elements and cores based on the subchannel approach. The existing COBRA-IV-I code is the control data corporation (CDC) CYBER version, which has limitations on the computer core storage and gives some inconvenience to the user interface. To solve these problems, we have converted the COBRA-IV-I code form the CDC CYBER mainframe to an Hewlett Packard (HP) 9000/700-series workstation version, and have verified the converted code. as a result, we have found almost no difference between the two versions in their calculation results. Therefore we expect the HP 9000/700 version of the COBRA-IV-I code to be the basis for the future development of an improved multichannel analysis code under the more convenient user environment. (author). 3 tabs., 2 figs., 8 refs

  11. The Development of Boiler Pipes Used for 700°C A-USC-PP in China

    Science.gov (United States)

    Liu, Zhengdong; Bao, Hansheng; Xu, Songqian; Wang, Qijiang; Yang, Yujun; Zhang, Peng; Lei, Bingwang

    This paper introduces the progress of boiler pipes used for the manufacturing of 700°C advanced ultra-super-critical (A-USC) fossil fuel power plants (PP) in China, with the emphasis on the detailed advancements of G115 and CN617 pipes, including technical exploration, industrial production and microstructure-property investigation. G115 is a novel ferritic heat resistant steels developed by CISRI, which is an impressive candidate material to make pipes for the temperature up to 650°C. CN617 is a recent modification of Inconel617B and the CN617 pipe with the dimension of Φ 460 × 80 mm was successfully manufactured in China. Some newly available data associated with above materials will be released. G115 and CN617 are imposing candidate materials for the manufacturing of 700°C advanced ultra-super-critical (A-USC) fossil fuel power plants (PP) in China.

  12. A High Isolation MIMO Antenna without Decoupling Structure for LTE 700 MHz

    Directory of Open Access Journals (Sweden)

    Yanjie Wu

    2015-01-01

    Full Text Available This paper presents a long-term evolution (LTE 700 MHz band multiple-input-multiple-output (MIMO antenna, and high isolation between the two symmetrical antenna elements is obtained without introducing extra decoupling structure. Each antenna element is a combination antenna of PIFA and a meander monopole antenna. The end of the PIFA and the meander monopole antenna are, respectively, overlapped with the 50 Ω microstrip feed line, the two overlapping areas produce additional capacitance which can be considered decoupling structures to enhance the isolation for the MIMO antenna, as well as the impedance matching of the antenna elements. The MIMO antenna is etched on FR4 PCB board with dimensions of 71 × 40 × 1.6 mm3; the edge-to-edge separation of the two antenna elements is only nearly 0.037 λ at 700 MHz. Both simulation and measurement results are used to confirm the MIMO antenna performance; the operating bandwidth is 698–750 MHz with S11≤−6 dB and S21≤−23 dB.

  13. Experimental Investigation of Phase Equilibria in the Ho-Ti-Si Ternary System at 973 K (700 °C)

    Science.gov (United States)

    Han, Feng; Zhan, Yongzhong

    2018-02-01

    Phase equilibrium relations of the Ho-Ti-Si ternary system at 973 K (700 °C) were experimentally researched by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive spectrometer (EDS). The isothermal section of the system at 973 K (700 °C) consists of 14 three-phase regions, 27 two-phase regions, and 14 single-phase regions. The phases Ti5Si3, Ti5Si4, TiSi, TiSi2, Ho5Si3, Ho5Si4, HoSi, αHoSi2-b, and βHoSi2-a are proved to exist at 973 K (700 °C). Previously reported HoTiSi and Ho2Ti3Si4 ternary compounds were confirmed to exist at this temperature. The solubility of Ho in the intermediate phases (i.e., TiSi2, TiSi, Ti5Si4, and Ti5Si3) at the Ti-Si side is extremely small. The maximum solubilities of Ti in HoSi2-b, Ho5Si4, and Ho5Si3 are confirmed to be 8.0, 7.2, and 6.0 at. pct, respectively.

  14. Spiral Slotted Microstrip Antenna Design for 700 MHz Band Application

    Directory of Open Access Journals (Sweden)

    Ricardo Meneses González

    2016-01-01

    Full Text Available This work describes the design and implementation of spiral slotted microstrip antenna. Recently, just like other countries, in Mexico, terrestrial digital television has been implemented (analogic shutdown; as a consequence, the 700 MHz UFH Band (698–806 MHz has been opened to new telecommunications services, particularly wireless mobile communication. This technological advance represents a radio mobile antenna design challenge because it is necessary to design an antenna whose dimensions must be small enough, which satisfies gain, resonance frequency, and bandwidth requirements and is of low cost.

  15. 13 CFR 126.700 - What are the performance of work requirements for HUBZone contracts?

    Science.gov (United States)

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false What are the performance of work... ADMINISTRATION HUBZONE PROGRAM Contract Performance Requirements § 126.700 What are the performance of work... meet the performance of work requirements set forth in § 125.6(c) of this chapter. (b) In addition to...

  16. "Stiction Syndrome": Non-Operative Management of Patients With Difficult AMS 700 Series Inflation.

    Science.gov (United States)

    Kavoussi, Nicholas L; Viers, Boyd R; VanDyke, Maia E; Pagliara, Travis J; Morey, Allen F

    2017-09-01

    Static friction (stiction) is a mechanical phenomenon in which a state of increased resistance exists across a control valve mechanism. To present a strategy for non-operative management of inflatable penile prosthesis (IPP) cases with pump malfunction from pump valve stiction. All patients had American Medical Systems (AMS; Minnetonka, MN, USA) 700 series Momentary Squeeze IPPs with transient pump malfunction owing to pump valve stiction after extended periods of device inactivity. Our evolving non-operative management experience with the "forced deflation" maneuver is described. This technique has successfully prevented the need for surgical pump replacement. Of patients with IPP who were instructed to inflate and deflate daily to prevent stiction recurrence, none have re-presented with difficult inflation. Of 306 patients receiving the AMS 700 series IPP at our institution from 2007 through 2015, 6 (1.9%) presented with difficulty activating the Momentary Squeeze pump (from 2011 through 2015). Four additional patients were referred from outside institutions with the same complaint. All patients (10 of 10, 100%) presented after a prolonged period of inactivity (minimum = 6 weeks) during which the IPP was not cycled and remained stagnant. Although the initial four patients (40%) underwent surgical exploration with pump mobilization and replacement, the six most recent patients (60%) were successfully instructed in the forced deflation maneuver in the office, which enabled the device to cycle normally thereafter. Device inactivity, for as little as 6 weeks, can predispose to Momentary Squeeze pump valve malfunction; and a regimen of daily IPP cycling could prevent stiction-related malfunction. Our findings should encourage practitioners to attempt conservative management of patients with "stiction syndrome" whenever possible, thereby avoiding unnecessary surgery. Kavoussi NL, Viers BR, VanDyke ME, et al. "Stiction Syndrome": Non-Operative Management of Patients

  17. Phase equilibria in the ternary In-Ni-Sn system at 700 °C.

    Science.gov (United States)

    Schmetterer, C; Zemanova, A; Flandorfer, H; Kroupa, A; Ipser, H

    2013-04-01

    The phase equilibria of the ternary system In-Ni-Sn were investigated experimentally at 700 °C using X-ray diffraction (XRD) and scanning electron microscopy (SEM) including electron micro probe analysis (EMPA) and energy dispersive X-ray spectroscopy (EDX). A corresponding isothermal section was established based on these results. This particular temperature was chosen because it allowed obtaining reliable results within reasonable time. The existence of the ternary phase InNi 6 Sn 5 was confirmed whereas the ternary compound In 2 NiSn, reported earlier in literature, was found to be part of a large solid solution field based on binary InNi. The ternary solubility of the binary phases was established, and continuous solid solutions were found between the isostructural phases Ni 3 Sn LT and InNi 3 as well as between Ni 3 Sn 2 HT and InNi 2 . In addition, this isothermal section could be well reproduced by CALPHAD modelling. The resulting calculated isotherm at 700 °C is presented, too, and compared with the experimental results.

  18. 20 CFR 663.700 - What are the requirements for on-the-job training (OJT)?

    Science.gov (United States)

    2010-04-01

    ...-the-Job Training (OJT) and Customized Training § 663.700 What are the requirements for on-the-job training (OJT)? (a) On-the-job training (OJT) is defined at WIA section 101(31). OJT is provided under a... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false What are the requirements for on-the-job...

  19. 15 CFR Appendix I to Part 700 - Form BIS-999-Request for Special Priorities Assistance

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Form BIS-999-Request for Special Priorities Assistance I Appendix I to Part 700 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL...

  20. 76 FR 51271 - Implementing a Nationwide, Broadband, Interoperable Public Safety Network in the 700 MHz Band

    Science.gov (United States)

    2011-08-18

    ... 700 MHz Band AGENCY: Federal Communications Commission. ACTION: Final rule. SUMMARY: In this document... medical services, Incorporation by reference, Individuals with disabilities, Radio, Reporting and...- 798 MHz bands. * * * * * Service Availability. The use of a public safety broadband network on a day...

  1. Production equipment development needs for a 700 metric ton/year light water reactor mixed oxide fuel manufacturing plant

    International Nuclear Information System (INIS)

    Blahnik, D.E.

    1977-09-01

    A literature search and survey of fuel suppliers was conducted to determine how much development of production equipment is needed for a 700 metric tons/y LWR mixed-oxide (UO 2 --PuO 2 ) fuel fabrication plant. Results indicate that moderate to major production equipment development is needed in the powder and pellet processing areas. The equipment in the rod and assembly processing areas need only minor development effort. Required equipment development for a 700 MT/y plant is not anticipated to delay startup of the plant. The development, whether major or minor, can be done well within the time frame for licensing and construction of the plant as long as conventional production equipment is used

  2. Safety and clinical effect of i.v. infusion of cyclopropyl-methoxycarbonyl etomidate (ABP-700), a soft analogue of etomidate, in healthy subjects.

    Science.gov (United States)

    Valk, B I; Absalom, A R; Meyer, P; Meier, S; den Daas, I; van Amsterdam, K; Campagna, J A; Sweeney, S P; Struys, M M R F

    2018-06-01

    Cyclopropyl-methoxycarbonyl metomidate, or ABP-700, is a second generation analogue of etomidate, developed to retain etomidate's beneficial haemodynamic and respiratory profile but diminishing its suppression of the adrenocortical axis. The objective of this study was to characterise the safety and efficacy of 30-min continuous infusions of ABP-700, and to assess its effect on haemodynamics and the adrenocortical response in healthy human volunteers. Five cohorts involving 40 subjects received increasing infusion doses of ABP-700, propofol 60 μg kg -1  min -1 or placebo. Safety was evaluated through adverse event (AE) monitoring, safety laboratory tests, and arterial blood gasses. Haemodynamic and respiratory stability were assessed by continuous monitoring. Adrenocortical function was analysed by adrenocorticotropic hormone (ACTH) stimulation tests. Clinical effect was measured using the modified observer's assessment of alertness/sedation (MOAA/S) and continuous bispectral index monitoring. No serious AEs were reported. Haemodynamic and respiratory effects included mild dose-dependent tachycardia, slightly elevated blood pressure, and no centrally mediated apnoea. Upon stimulation with ACTH, no adrenocortical depression was observed in any subject. Involuntary muscle movements (IMM) were reported, which were more extensive with higher dosing regimens. Higher dosages of ABP-700 were associated with deeper sedation and increased likelihood of sedation. Time to onset of clinical effect was variable throughout the cohorts and recovery was swift. Infusions of ABP-700 showed a dose-dependent hypnotic effect, and did not cause severe hypotension, severe respiratory depression, or adrenocortical suppression. The presentation and nature of IMM is a matter of concern. NTR4735. Copyright © 2018 British Journal of Anaesthesia. Published by Elsevier Ltd. All rights reserved.

  3. 700 fathom Depth Contour for Pacific Fishery Management Council's June 2005 Preferred Alternative, Groundfish EFH Final EIS

    Data.gov (United States)

    Pacific States Marine Fisheries Commission — These data depict the primary 700 fathom isobath within the West Coast Exclusive Economic Zone (EEZ). The area to the west of this depth contour was designated by...

  4. Evolution of microstructure and tensile properties of Fe–18Ni–12Cr based AFA steel during aging at 700 °C

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Man [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 10083 (China); Nuclear Materials Development Division, Korean Atomic Energy Research Institute, Daejeon 305-353 (Korea, Republic of); Sun, Hongying [School of Mechanical Engineering, Anyang Institute of Technology, Anyang 455002 (China); Phaniraj, Madakashira P.; Han, Heung Nam [Department of Materials Science and Engineering and Research Institute of Advanced Materials, Seoul National University, Seoul 151-744 (Korea, Republic of); Jang, Jinsung [Nuclear Materials Development Division, Korean Atomic Energy Research Institute, Daejeon 305-353 (Korea, Republic of); Zhou, Zhangjian, E-mail: zhouzhj@mater.ustb.edu.cn [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 10083 (China)

    2016-08-30

    The effects of aging at 700 °C on the microstructure and tensile properties of an alumina-forming austenitic (AFA) stainless steel were investigated. With increasing aging time, B2-NiAl and Laves phase precipitated first on grain boundaries (GB) and then in the grain interior. The GB precipitate coverage reached 74% after aging for 1000 h. The GB precipitates not only suppressed grain coarsening during aging, but also influenced the tensile fracture mode at 700 °C by partitioning stress concentration on triple junctions. Moreover plate-like and spherical NbC particles precipitated during aging. Spherical NbC with size of around 5 nm were stable, while plate-like NbC grew to 89 nm after aging for 1000 h. These precipitates played an important role on the tensile strength. Age hardening contributed to the increasing tensile strength at RT with aging time, while the softening mechanism of dynamic recovery dominated the tensile tests at 700 °C.

  5. The Cr–Fe–Nb ternary system: Experimental isothermal sections at 700 °C, 1050 °C and 1350 °C

    Energy Technology Data Exchange (ETDEWEB)

    Jacob, Aurélie, E-mail: a.jacob@fz-juelich.de [Forschungszentrum Juelich, IEK-2, 52425 Juelich (Germany); Schmetterer, Clemens [Forschungszentrum Juelich, IEK-2, 52425 Juelich (Germany); Fraunhofer-UMSICHT, 92237 Sulzbach-Rosenberg (Germany); Grüner, Daniel; Wessel, Egbert [Forschungszentrum Juelich, IEK-2, 52425 Juelich (Germany); Hallstedt, Bengt [Institute for Materials Applications in Mechanical Engineering, RWTH Aachen University, Augustinerbach 4, 52062 Aachen (Germany); Singheiser, Lorenz [Forschungszentrum Juelich, IEK-2, 52425 Juelich (Germany)

    2015-11-05

    The Cr–Fe–Nb system is an important constituent system in the development of Laves-phase reinforced steels. It contains two Laves-phase polytypes, i.e. C14–Fe{sub 2}Nb and C15–Cr{sub 2}Nb. While the first forms a substantial ternary solid solution with Cr, the latter only shows a limited solubility for Fe. The phase equilibria in the Cr–Fe–Nb system are shown in three isothermal sections at 700, 1050 and 1350 °C. Scanning electron microscopy coupled with energy dispersive X-ray analysis (SEM/EDX), X-ray diffraction (XRD) and electron back scatter diffraction (EBSD) were used to determine the phase equilibria from which the isothermal sections were constructed. - Highlights: • Determination of Phase Equilibria in the Cr–Fe–Nb system at 700, 1050 and 1350 °C. • Isothermal sections at 700, 1050 and 1350 °C were established. • Homogeneity range of Laves phases were determined. • Solubility of Fe and Cr and lattice parameter evolution in the ternary phases were determined.

  6. Process of treating carbonaceous materials. [400 to 700/sup 0/C, high vacuum

    Energy Technology Data Exchange (ETDEWEB)

    Parker, O J

    1913-11-24

    A process is given of treating carbonaceous materials, characterized by the material being submitted simultaneously to a temperature of 400 to 700/sup 0/C, a pressure between 5.0 mm of mercury under atmospheric and a practically perfect vacuum, and by the volatile material able to condense under the vacuum used being condensed practically under the same pressure for the production of a high proportion of condensable products and a superior fuel.

  7. The ISA 700 Auditor’s Report and the Audit Expectation Gap – Do Additional Explanations Matter?

    NARCIS (Netherlands)

    Gold, A.H.; Pott, C.; Gronewold, U.

    2012-01-01

    In this paper we test the effectiveness of explanations as mandated by the revised ISA 700 auditor's report in reducing the audit expectation gap. German auditors and financial statement users participated in an experiment where they read a summary of a firm's financial statements and an auditor's

  8. New implementation of an SX700 undulator beamline at the Advanced Light Source

    International Nuclear Information System (INIS)

    Warwick, T.; Andresen, N.; Comins, J.; Kaznacheyev, K.; Kortright, J.B.; McKean, P.J.; Padmore, H.A.; Shuh, D.K.; Stevens, T.; Tyliszczak, T.

    2004-01-01

    A newly engineered implementation of a collimated SX700-style beam line for soft x-rays is described. This facility is operational at the Advanced Light Source and delivers high brightness undulator beams to a scanning zone plate microscope and to an array of end stations for x-ray spectroscopic studies of wet surfaces. Switching between branches is motorized, servo-steering systems maintain throughput and the monochromator works together with the elliptical undulator for a fully automated facility

  9. Intraoperative Optical Coherence Tomography Using the RESCAN 700: Preliminary Results in Collagen Crosslinking.

    Science.gov (United States)

    Pahuja, Natasha; Shetty, Rohit; Jayadev, Chaitra; Nuijts, Rudy; Hedge, Bharath; Arora, Vishal

    2015-01-01

    To compare the penetration of riboflavin using a microscope-integrated real time spectral domain optical coherence tomography (ZEISS OPMI LUMERA 700 and ZEISS RESCAN 700) in keratoconus patients undergoing accelerated collagen crosslinking (ACXL) between epithelium on (epi-on) and epithelium off (epi-off). Intraoperative images were obtained during each of the procedures. Seven keratoconus patients underwent epi-on ACXL and four underwent epi-off ACXL. A software tool was developed using Microsoft.NET and Open Computer Vision (OpenCV) libraries for image analysis. Pre- and postprocedure images were analyzed for changes in the corneal hyperreflectance pattern as a measure of the depth of riboflavin penetration. The mean corneal hyperreflectance in the epi-on group was 12.97 ± 1.49 gray scale units (GSU) before instillation of riboflavin and 14.46 ± 2.09 GSU after AXCL (P = 0.019) while in the epi-off group it was 11.43 ± 2.68 GSU and 16.98 ± 8.49 GSU, respectively (P = 0.002). The average depth of the band of hyperreflectance in the epi-on group was 149.39 ± 15.63 microns and in the epi-off group it was 191.04 ± 32.18 microns. This novel in vivo, real time imaging study demonstrates riboflavin penetration during epi-on and epi-off ACXL.

  10. Intraoperative Optical Coherence Tomography Using the RESCAN 700: Preliminary Results in Collagen Crosslinking

    Directory of Open Access Journals (Sweden)

    Natasha Pahuja

    2015-01-01

    Full Text Available Purpose. To compare the penetration of riboflavin using a microscope-integrated real time spectral domain optical coherence tomography (ZEISS OPMI LUMERA 700 and ZEISS RESCAN 700 in keratoconus patients undergoing accelerated collagen crosslinking (ACXL between epithelium on (epi-on and epithelium off (epi-off. Methods. Intraoperative images were obtained during each of the procedures. Seven keratoconus patients underwent epi-on ACXL and four underwent epi-off ACXL. A software tool was developed using Microsoft.NET and Open Computer Vision (OpenCV libraries for image analysis. Pre- and postprocedure images were analyzed for changes in the corneal hyperreflectance pattern as a measure of the depth of riboflavin penetration. Results. The mean corneal hyperreflectance in the epi-on group was 12.97 ± 1.49 gray scale units (GSU before instillation of riboflavin and 14.46 ± 2.09 GSU after AXCL (P = 0.019 while in the epi-off group it was 11.43 ± 2.68 GSU and 16.98 ± 8.49 GSU, respectively (P = 0.002. The average depth of the band of hyperreflectance in the epi-on group was 149.39 ± 15.63 microns and in the epi-off group it was 191.04 ± 32.18 microns. Conclusion. This novel in vivo, real time imaging study demonstrates riboflavin penetration during epi-on and epi-off ACXL.

  11. Nuclear multifragmentation by 700–1500 MeV photons: New data of GRAAL experiment

    Energy Technology Data Exchange (ETDEWEB)

    Nedorezov, V. G., E-mail: vladimir@cpc.inr.ac.ru; Lapik, A. M. [Russian Academy of Sciences, Institute for Nuclear Research (Russian Federation); Collaboration: GRAAL Collaboration

    2015-12-15

    The cross sections of carbon nucleus photodisintegration into protons and neutrons with high multiplicity for photon energies from 700 to 1500 MeV were measured. The experiment was performed at the tagged photon beam of the GRAAL setup using the wide-aperture detector LAGRANγE. It was shown that multifragmentation up to complete disintegration into separate nucleons is initiated by elementary reactions of meson photoproduction with a subsequent intranuclear cascade.

  12. Differential cross sections of proton Compton scattering at photon laboratory energies between 700 and 1000 MeV

    International Nuclear Information System (INIS)

    Jung, M.; Kattein, J.; Kueck, H.; Leu, P.; Marne, K.D. de; Wedemeyer, R.; Wermes, N.

    1981-05-01

    Differential cross sections of proton Compton scattering have been measured at the Bonn 2.5 GeV synchrotron. 78 data points are presented as angular distributions at photon lab energies of 700, 750, 800, 850, 900, and 950 MeV. The c.m. scattering angle ranges from 40 0 to 130 0 , corresponding to a variation of the four momentum transfer squared between t = -0.10 to t = -0.96 GeV 2 at 700 and 950 MeV, respectively. Two additional differential cross sections have been measured at 1000 MeV, 35.6 0 and 47.4 0 . The angular distributions show forward peaks whose extrapolations to 0 0 are consistent with calculated forward cross sections taken from literature. The small angle data ( vertical stroke t vertical stroke approx. 2 ) together with the calculated cross sections at 0 0 are also consistent with the assumption of a slope parameter B of 5 GeV -2 . For the first time a re-rise of the angular distributions towards backward angles has been observed. It becomes less steep with increasing energy. The most interesting feature of the angular distributions is a sharp structure which appears between t = -0.55 GeV 2 at 700 MeV and t = -0.72 GeV 2 at 950 MeV. Such a rapid variation of the differential cross section with t has never been observed in elastic hadron-hadron scattering or photoproduction processes. It indicates the existence of a dynamical mechanism which could be a peculiarity of Compton scattering. (orig.)

  13. 78 FR 66298 - Promoting Interoperability in the 700 MHz Commercial Spectrum; Requests for Waiver and Extension...

    Science.gov (United States)

    2013-11-05

    ... when the two operators use the same 2G and 3G technologies and bands), and Band Class 12 devices and... Lower 700 MHz band to improve choice and quality for consumers of mobile services. The Commission... an efficient and effective manner to improve choice and quality for consumers of mobile services. A...

  14. Component behaviour in the 700 C power plant. Numerical and experimental investigations

    International Nuclear Information System (INIS)

    Schmidt, Kay H.

    2013-01-01

    Currently martensitic steels are used in fossil fired power plants with maximum working temperatures up to 625 C. These steels do not show the required creep rupture strength at the target temperature of 700 C. For these high temperatures, new materials like the nickel base alloys have to be qualified for power plants services. Originating from the weld of turbine materials, nickel base alloys show outstanding creep rupture strength. An alloy with good prospects out of the material class of the nickel base alloys is Alloy 617 mod. However, this material is expensive due to its high nickel content. Furthermore, the complex machinability of this material leads to an additional increase in expenses. A complete fabrication of the boiler area using Alloy 617 mod is not economically feasible, which means that the usage of this material has to be limited to the temperature weld of 625 C to 700 C. For the boiler area with temperatures below 625 C the well proven 9 % to 12 % Cr-steels, like T/P92 and VM12/VM12-SHC may be used. In the weld of low temperatures up to 525 C the usage of the 2.5 % Cr-steel T/P24 offers numerous advantages, in particular in the fabrication of membrane walls. This material shows good creep properties up to temperatures of 525 C and, for thin walled components, T24 can be welded without post weld heat treatment by using suitable techniques. For a successful design and fabrication of a 700 C fossil fired power plant, appropriate materials have to be qualified. Here, a special focus is set on the creep properties of these materials. The presented work is a significant contribution to the qualification of these materials. First, the materials Alloy 617 mod, T/P92, VM12/VM12-SHC and T24 are briefly introduced and characterized. After this, the materials are investigated in a detailed creep testing program. This program includes investigations on base material, extracted from tubes, pipes and inductive bends of pipes. In addition, crossweld specimens

  15. The accelerated oxidation of zircaloy-4 at 700∼900 .deg. C in high pressure steam

    International Nuclear Information System (INIS)

    Kim, K. P.; Park, K. H.

    1999-01-01

    To find the effect of pressure on the high temperature oxidation of zircaloy-4, an autoclave capable of measuring the degree of oxidation at high temperatures and high pressure was manufactured. The specimens used in experiments are commercially available Zircaloy-4 used in Kori nuclear power plants. All the measurements were done at 700∼900 .deg. C in steam. Pressure effects were noticed. The oxide thickness was much thicker in high pressure steam, comparing to that in the 1 atm steam. And, the higher is the steam pressure, the thicker becomes the oxide. The enhancement of oxide growth rate at 700∼900 .deg. C in high pressure steam is approximately propotion to the power of 1.0∼1.6 of the ratio of experimental steam pressure to critical steam pressure. There is a critical steam pressure above that the oxidation rate enhances. The critical steam pressure was measured as 30∼40 bar. The enhanced oxidation seems from the oxide cracking due to the tetragonal to monoclinic phase transformation at high pressure steam

  16. Thermodynamic study of the thorium-hydrogen system at 700 K

    International Nuclear Information System (INIS)

    Picard, C.; Kleppa, O.J.

    1980-01-01

    The partial enthalpies of solution of hydrogen in thorium-hydrogen alloys with H/Th ratios ranging from 0 to 2 have been measured calorimetrically at 700 K. From these data we calculate the standard enthalpy of formation of ThH 2 at this temperature to be -34.8 kcal mol -1 with an estimated uncertainty of +- 0.2 kcal mol -1 . This agrees well with values calculated by earlier investigators from plateau pressure equilbrium data. For several alloy compositions within the nearly stoichiometric phase ThH 2 the equilibrium pressures of hydrogen also were determined. Comparisons of the relative partial Gibbs energies of hydrogen obtained from these equilibrium pressures with corresponding enthalpies from calorimetry provide information on the partial entropy. The partial enthalpy and entropy both change dramatically with composition between H/Th = 1.99 and 2.003

  17. 700 TWh dry gas for NOK 0,10 per kWh

    International Nuclear Information System (INIS)

    2003-01-01

    In 2002, Norway exported natural gas corresponding to a heat value of 700 TWh. The article looks at what energy price the big gas customers on the continent and in Great Britain really paid for the Norwegian gas. The average price to the wholesale dealer was NOK 0,10/kWh. However, the wholesale dealers quadruple the price out to the end-users. It is also found that if the gas was made available on the home market, then the Norwegian gas distributors would be able to compete on price with the foreign distributors. This fact along with the extreme price on electricity in the winter 2003 gives an impetus to the debate that goes on in Norway on whether or not to build gas power plants

  18. Development of 700 pps high-duty-cycle line-type pulse modulator

    Energy Technology Data Exchange (ETDEWEB)

    Baba, H.; Satoh, K.; Miura, A. [NIHON KOSHUHA Co., LTD., Yokohama, Kanagawa (Japan)] [and others

    1997-04-01

    The high-duty-cycle line-type pulse modulator has been developed to drive the 5.5 MW S-band klystron at the 700 pps maximum repetition-rate and the 14 {mu}sec flat-top pulse-width. To keep an enough recovery time to the thyratron-tube, the command charging scheme was adopted. To do this, a charging SCR-bank has been developed, which is capable of handling the peak charging current of 50 A. The system achieved the world wide highest average output-power of 205 kW. Two modulators have been installed in a new high-duty-cycle electron linear accelerator, which has been started its business operation in March 1996 as an electron-beam-sterilization facility. (J.P.N)

  19. A 700-year record of mercury in avian eggshells of Guangjin Island, South China Sea

    Energy Technology Data Exchange (ETDEWEB)

    Xu Liqiang [Institute of Polar Environment, University of Science and Technology of China, Hefei, Anhui 230026 (China); USTC-CityU Joint Advanced Research Center, Suzhou, Jiangsu 215123 (China); Liu Xiaodong, E-mail: ycx@ustc.edu.cn [Institute of Polar Environment, University of Science and Technology of China, Hefei, Anhui 230026 (China); Sun Liguang, E-mail: slg@ustc.edu.cn [Institute of Polar Environment, University of Science and Technology of China, Hefei, Anhui 230026 (China); Chen Qianqian; Yan Hong; Liu Yi; Luo Yuhan; Huang Jing [Institute of Polar Environment, University of Science and Technology of China, Hefei, Anhui 230026 (China)

    2011-04-15

    Ancient eggshells over the past 700 years were extracted from an ornithogenic sediment profile on Guangjin Island, South China Sea. Based on SEM and nitrogen isotope analyses, we determined that neither post-depositional processes nor seabirds' dietary changes had a large influence on eggshell Hg levels. The historical change of Hg in these eggshells was reconstructed. Eggshell Hg was a marker for past Hg deposition in marine environment. The eggshell Hg showed three small peaks at around 1300AD, 1600 AD and 1700-1750AD and rapid increase since 1800 AD. Before 1970 AD the Hg deposition in the Xisha area had global distribution characteristics, with increased Hg emissions due to global anthropogenic activities in industrial times. However, after 1970 AD, a further sharp increase up to present day occurred, implying that the Hg production center had gradually shifted from Europe and America to Asia. - Research highlights: > Eggshell Hg is a marker for past mercury deposition in marine environment. > This is a Hg record from ancient sequential eggshell samples. > The 700-year record of eggshell Hg is closely related to human activities. > Eggshell Hg suggests the increase of Hg production in Asia over the past decades. - Our work provides a potential use of ancient sequential eggshells to reconstruct past mercury deposition in marine ecosystems.

  20. Research on the Superheater Material Properties for USC Boiler with 700°C Steam Parameter

    Science.gov (United States)

    Chongbin, Wang; Xueyuan, Xu; Yufeng, Zhu; Yongqiang, Jin; Hui, Tong; Yu, Wang; Xiaoli, Lu

    This paper discusses the materials' properties of superheater for 700°C USC boiler, including Sanicro25, HR6W, 617mod and 740H, and analyzes the range of applicable temperature of superheater made of different tubes, such as T91, T92, Super304H, TP310HCbN, Sanicro25, HR6W, 617Mod and 740H. In addition, some suggestions on the material selection have been proposed.

  1. Complex Analysis of 700-Year-Old Skeletal Remains found in an Unusual Grave: Case Report

    Czech Academy of Sciences Publication Activity Database

    Vaněk, D.; Brzobohatá, Hana; Šilerová, M.; Horák, Z.; Nývltová Fišáková, Miriam; Vašinová Galiová, M.; Zedníková Malá, P.; Urbanová, V.; Dobisíková, M.; Beran, M.; Brestovanský, P.

    2015-01-01

    Roč. 2, č. 5 (2015) ISSN 2332-0915 R&D Projects: GA ČR GB14-36938G Grant - others:GA MŠk(CZ) ED1.1.00/02.0068 Program:ED Institutional support: RVO:67985912 ; RVO:68081758 Keywords : mass spectrometry * genealogical * physical anomalies * anthropological Subject RIV: AC - Archeology, Anthropology, Ethnology http://www.omicsonline.org/ open - access /complex-analysis-of-700yearold-skeletal-remains-found-in-an-unusualgravecase-report-2332-0915-1000138.pdf

  2. Monitoring of dams according to German standard DIN 19 700 on the basis of a GIS based expert system; Stauanlagenueberwachung nach DIN 19 700 in Verbindung mit Expertensystemen auf GIS-Basis

    Energy Technology Data Exchange (ETDEWEB)

    Kast, Karl; Saucke, Ulrich; Elsaesser, Ralph [Dr.-Ing. Karl Kast + Partner (GbR) Ingenieurgemeinschaft fuer Umwelt- und Geotechnik, Ettlingen (Germany)

    2010-07-01

    The German standard DIN 19 700 stipulates regular safety reports assessing dams and their operation as part of the continuous dam monitoring scheme. Experience has shown that a GIS based dam monitoring system exhibits evident advantages regarding a continuous assessment. Besides and easy access to all relevant information grouped by themes, it offers a graphic analysis of measuring data and their display in the GIS system. In addition, concerning relevant failure mechanism, individual modules of a GIS based expert system are designed for the purpose of assessing the safety of the dam in the event of uncommon incidents. (orig.)

  3. Experimental study of the Cu–Ni–Y system at 700 °C using diffusion couples and key alloys

    Energy Technology Data Exchange (ETDEWEB)

    Mezbahul-Islam, Mohammad, E-mail: mmedraj@encs.concordia.ca [Department of Mechanical Engineering, Concordia University, 1455 de Maisonneuve Blvd. West, Montreal, Quebec, Montreal, Canada H3G 1M8 (Canada); Medraj, Mamoun [Department of Mechanical Engineering, Concordia University, 1455 de Maisonneuve Blvd. West, Montreal, Quebec, Montreal, Canada H3G 1M8 (Canada)

    2013-06-05

    Highlights: ► Isothermal section at 700 °C of the Cu–Ni–Y system has been constructed. ► Diffusion couple technique has been used to understand the phase relations. ► Complete mutual solubility between CuY{sup *}–NiY and Cu{sub 4}Y–Ni{sub 4}Y have been determined. ► Maximum ternary solubility of the binary compounds has been determined. -- Abstract: Two solid–solid diffusion couples and 29 key samples have been used to construct the isothermal section of the Cu–Ni–Y system at 700 °C. Phase relations and ternary solubility of the binary compounds have been determined using scanning electron microscopy (SEM), wave dispersive X-ray spectrometer (WDS) and X-ray diffraction (XRD) analysis. The isothermal section at 700 °C consists of two single-phase region, 21 two-phase regions and 10 three-phase regions. Two extended solid solutions, between CuY{sup *}–NiY and Cu{sub 4}Y–Ni{sub 4}Y have been determined. The maximum solubility of Ni in Cu{sub 2}Y, Cu{sub 7}Y{sub 2} and Cu{sub 6}Y has been found to be about 28, 7.5 and 3.9 at.% Ni, respectively. The solubility of Cu in NiY{sub 3}, Ni{sub 2}Y, Ni{sub 3}Y, Ni{sub 7}Y{sub 2}, Ni{sub 5}Y and Ni{sub 17}Y{sub 2} is about 12.04, 9.67, 25, 3.08, 75 and 37 at.%. Cu, respectively. The solubility of Y in fcc (Cu, Ni) phase is about 0.6 at.%.

  4. The system Cu-Rh-S at 900 degrees, 700 degrees, 540 degrees and 500 degrees C

    DEFF Research Database (Denmark)

    Karup-Møller, Sven; Makovicky, E.

    2007-01-01

    Phase relations in the dry condensed system Cu-Rh-S were determined at 900, 700, 540 and 500 degrees C. At 900 degrees C, the system contains digenite, four rhodium sulfides (Rh17S15, Rh3S4, Rh2S3 and RhS similar to 3), three ternary sulfides (CuRh2S4, CuxRhS3+x and a fibrous sulfide in the range...

  5. Molecular analysis of a 11 700-year-old rodent midden from the Atacama Desert, Chile

    Science.gov (United States)

    Kuch, M.; Rohland, N.; Betancourt, J.L.; Latorre, C.; Steppan, S.; Poinar, H.N.

    2002-01-01

    DNA was extracted from an 11 700-year-old rodent midden from the Atacama Desert, Chile and the chloroplast and animal mitochondrial DNA (mtDNA) gene sequences were analysed to investigate the floral environment surrounding the midden, and the identity of the midden agent. The plant sequences, together with the macroscopic identifications, suggest the presence of 13 plant families and three orders that no longer exist today at the midden locality, and thus point to a much more diverse and humid climate 11 700 years ago. The mtDNA sequences suggest the presence of at least four different vertebrates, which have been putatively identified as a camelid (vicuna), two rodents (Phyllotis and Abrocoma), and a cardinal bird (Passeriformes). To identify the midden agent, DNA was extracted from pooled faecal pellets, three small overlapping fragments of the mitochondrial cytochrome b gene were amplified and multiple clones were sequenced. These results were analysed along with complete cytochrome b sequences for several modern Phyllotis species to place the midden sequence phylogenetically. The results identified the midden agent as belonging to an ancestral P. limatus. Today, P. limatus is not found at the midden locality but it can be found 100 km to the north, indicating at least a small range shift. The more extensive sampling of modern Phyllotis reinforces the suggestion that P. limatus is recently derived from a peripheral isolate.

  6. A 700-year record of mercury in avian eggshells of Guangjin Island, South China Sea

    International Nuclear Information System (INIS)

    Xu Liqiang; Liu Xiaodong; Sun Liguang; Chen Qianqian; Yan Hong; Liu Yi; Luo Yuhan; Huang Jing

    2011-01-01

    Ancient eggshells over the past 700 years were extracted from an ornithogenic sediment profile on Guangjin Island, South China Sea. Based on SEM and nitrogen isotope analyses, we determined that neither post-depositional processes nor seabirds' dietary changes had a large influence on eggshell Hg levels. The historical change of Hg in these eggshells was reconstructed. Eggshell Hg was a marker for past Hg deposition in marine environment. The eggshell Hg showed three small peaks at around 1300AD, 1600 AD and 1700-1750AD and rapid increase since 1800 AD. Before 1970 AD the Hg deposition in the Xisha area had global distribution characteristics, with increased Hg emissions due to global anthropogenic activities in industrial times. However, after 1970 AD, a further sharp increase up to present day occurred, implying that the Hg production center had gradually shifted from Europe and America to Asia. - Research highlights: → Eggshell Hg is a marker for past mercury deposition in marine environment. → This is a Hg record from ancient sequential eggshell samples. → The 700-year record of eggshell Hg is closely related to human activities. → Eggshell Hg suggests the increase of Hg production in Asia over the past decades. - Our work provides a potential use of ancient sequential eggshells to reconstruct past mercury deposition in marine ecosystems.

  7. Retrospective study of pre-anesthetic electrocardiogram examination of 700 dogs conducted at the Veterinary Hospital of UFMG (2013-2014

    Directory of Open Access Journals (Sweden)

    Ana Flávia Machado Botelho

    2016-02-01

    Full Text Available Abstract: Pre-operative electrocardiograms performed in 700 dogs were analyzed in order to establish correlation between sex, age, indication for surgery, body condition score, breed and weight. Initially a clinical questionnaire was filled out from each owner, including age, breed, sex, weight, clinical history and surgical indication. Dogs above 6 years of age or those showing any kind of cardiac auscultation disturbances were referred to electrocardiogram (ECG evaluation. All ECG were performed and analyzed by the same veterinary specialist. Abnormalities at ECG were founnd in 364 of 700 (52% evaluated dogs, and the most frequent variation was sinus arrhythmia, observed in 293 dogs (25.4%. No significant correlation was found between the electrocardiographic alterations with weight, sex and age of the animals. Therefore ECG should be conducted routinely regardless of age, sex, breed or surgical indication, highlighting its value for determining a safe anesthetic protocol that promotes minimal cardiopulmonary depression and allows rapid post-surgical recovery.

  8. Evaluation of anticipatory signal to steam generator pressure control program for 700 MWe Indian pressurized heavy water reactor

    International Nuclear Information System (INIS)

    Pahari, S.; Hajela, S.; Rammohan, H. P.; Malhotra, P. K.; Ghadge, S. G.

    2012-01-01

    700 MWe Indian Pressurized Heavy Water Reactor (IPHWR) is horizontal channel type reactor with partial boiling at channel outlet. Due to boiling, it has a large volume of vapor present in the primary loops. It has two primary loops connected with the help of pressurizer surge line. The pressurizer has a large capacity and is partly filled by liquid and partly by vapor. Large vapor volume improves compressibility of the system. During turbine trip or load rejection, pressure builds up in Steam Generator (SG). This leads to pressurization of Primary Heat Transport System (PHTS). To control pressurization of SG and PHTS, around 70% of the steam generated in SG is dumped into the condenser by opening Condenser Steam Dump Valves (CSDVs) and rest of the steam is released to the atmosphere by opening Atmospheric Steam Discharge Valves (ASDVs) immediately after sensing the event. This is accomplished by adding anticipatory signal to the output of SG pressure controller. Anticipatory signal is proportional to the thermal power of reactor and the proportionality constant is set so that SG pressure controller's output jacks up to ASDV opening range when operating at 100% FP. To simulate this behavior for 700 MWe IPHWR, Primary and secondary heat transport system is modeled. SG pressure control and other process control program have also been modeled to capture overall plant dynamics. Analysis has been carried out with 3-D neutron kinetics coupled thermal hydraulic computer code ATMIKA.T to evaluate the effect of the anticipatory signal on PHT pressure and over all plant dynamics during turbine trip in 700 MWe IPHWR. This paper brings out the results of the analysis with and without considering anticipatory signal in SG pressure control program during turbine trip. (authors)

  9. 75 FR 58290 - Airworthiness Directives; Rolls-Royce plc RB211 Trent 700 and Trent 800 Series Turbofan Engines

    Science.gov (United States)

    2010-09-24

    ... Airworthiness Directives; Rolls-Royce plc RB211 Trent 700 and Trent 800 Series Turbofan Engines AGENCY: Federal... or increase the scope of the AD. Costs of Compliance Based on the service information, we estimate.... Required parts would cost about $15,000 per product. Based on these figures, we estimate the cost of the AD...

  10. Area West of the 700 fathom Depth Contour for Pacific Fishery Management Council's June 2005 Preferred Alternative, Groundfish EFH Final EIS

    Data.gov (United States)

    Pacific States Marine Fisheries Commission — These data depict area within the West Coast Exclusive Economic Zone (EEZ) that is west of the 700 fathom isobath. This area was designated by the Pacific Fishery...

  11. Eutectic Composite Turbine Blade Development

    Science.gov (United States)

    1976-11-01

    Special Metals Corporation. Several problems were encountered with this heat (DS 729), causing it to be scrapped. These included: runout of 92...of work removed/volume of wheel worn), were found to be 9.7, which is equiva- lent to Astroloy at 9.0, M252 at 10.0, and Udimet 500 at 8.0...fu|.,i|.^,UU4,,i,iW|j|i| TABLE yz RECOMMENDED CONVENTIONAL MACHINING CONDITIONS Surface Grinding (Low Stress) Wheel Speed Table Speed Cross

  12. Life Prediction on a T700 Carbon Fiber Reinforced Cylinder with Limited Accelerated Life Testing Data

    OpenAIRE

    Ma Xiaobing; Zhang Yongbo

    2015-01-01

    An accelerated life testing investigation was conducted on a composite cylinder that consists of aluminum alloy and T700 carbon fiber. The ultimate failure stress predictions of cylinders were obtained by the mixing rule and verified by the blasting static pressure method. Based on the stress prediction of cylinder under working conditions, the constant stress accelerated life test of the cylinder was designed. However, the failure data cannot be sufficiently obtained by the accelerated life ...

  13. 13 CFR 107.700 - Compliance with size standards in part 121 of this chapter as a condition of Assistance.

    Science.gov (United States)

    2010-01-01

    ... Assistance SMALL BUSINESS ADMINISTRATION SMALL BUSINESS INVESTMENT COMPANIES Financing of Small Businesses by Licensees Determining the Eligibility of A Small Business for Sbic Financing § 107.700 Compliance with size... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Compliance with size standards in...

  14. 13 CFR 108.700 - Compliance with size standards in part 121 of this chapter as a condition of Assistance.

    Science.gov (United States)

    2010-01-01

    ... Assistance SMALL BUSINESS ADMINISTRATION NEW MARKETS VENTURE CAPITAL (âNMVCâ) PROGRAM Financing of Small Businesses by NMVC Companies Determining the Eligibility of A Small Business for Nmvc Financing § 108.700... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Compliance with size standards in...

  15. 76 FR 24793 - Airworthiness Directives; Rolls-Royce plc (RR) RB211-524 Series and RB211 Trent 500, 700, and 800...

    Science.gov (United States)

    2011-05-03

    ... Airworthiness Directives; Rolls-Royce plc (RR) RB211-524 Series and RB211 Trent 500, 700, and 800 Series... the AD. Costs of Compliance Based on the service information, we estimate that this AD would affect...

  16. Molecular orbital study of the primary electron donor P700 of photosystem I based on a recent X-ray single crystal structure analysis

    International Nuclear Information System (INIS)

    Plato, Martin; Krauss, Norbert; Fromme, Petra; Lubitz, Wolfgang

    2003-01-01

    The X-ray structure analysis of photosystem (PS) I single crystals showed that the primary electron donor P700 is a heterodimer formed by one chlorophyll (Chl) a and one Chl a ' [Nature 411 (2001) 909]. The electronic structure of the cation radical P700 +· of the primary donor, which is created in the charge separation process, has been probed by semiempirical molecular orbital calculations including spin polarization effects (RHF-INDO/SP). The calculations, which were based on the X-ray structure, clearly show that P700 is a supermolecule formed by two chlorophyll species. They furthermore predict an asymmetrical charge and spin density distribution in favor of the monomeric Chl a half of this dimer in accordance with results from earlier EPR and ENDOR studies [J. Phys. Chem. B 105 (2000) 1225]. The stepwise inclusion of various electrostatic interactions of the dimer with its nearest surrounding (one threonine forming a hydrogen bond to the keto group of Chl a ' and two histidines liganding the Mg atoms of the two chlorophylls) leads to a systematic enhancement of this electronic asymmetry yielding a spin density ratio of almost 5:1 as also found experimentally. A large part of this value is caused by spin polarization effects. This result is only weakly affected by the electrostatic field of more remote amino acid residues and other pigment molecules ('accessory' Chl a molecules) present in PS I. A separate group of calculations involving local geometry optimizations by energy minimization techniques yields a further enhancement of the spin density asymmetry. A particularly strong effect is obtained by allowing for variations of the geometry of the vinyl groups on both chlorophylls of the P700 dimer. Theoretical results for individual isotropic proton and nitrogen hyperfine coupling constants, showing a satisfactory agreement with experimental findings, are also presented

  17. An Analysis of Flow in Rotating Passage of Large Radial-Inlet Centrifugal Compressor at Tip Speed of 700 Feet Per Second

    National Research Council Canada - National Science Library

    Prian, Vasily

    1951-01-01

    An analysis was made of the flow in the rotating passages of a 48-inch diameter radial-inlet centrifugal impeller at a tip speed of 700 feet per second in order to provide more knowledge on the flow...

  18. Current status of 700 MWe class PHWR NSSS design and engineering technology

    International Nuclear Information System (INIS)

    Park, Tae Keun; Suh, Sung Ki

    1996-06-01

    The capability of NSSS design and engineering technology of KAERI for 700 MWe class PHWR (CANDU 6) as of 1996 March 30 is comprehensively summarized in this report. The design and engineering capability of KAERI which have been gained during the implementation of Wolsung 2, 3 and 4 project are assessed, and showed with tangible scale. The status of Technology Transfer Materials received from Atomic Energy of Canada Limited under the Technology Transfer Agreement (TTA) which is effective simultaneously to Wolsung 3 and 4 contract, is also given in this report. The division of responsibility (DOR) of KAERI for Wolsung 2 and Wolsung 3 and 4 contract is also given, and expansion of DOR from Wolsung 2 contract to Wolsung 3 and 4 is presented. 3 refs. (Author)

  19. A Phase 1, Single-center, Double-blind, Placebo-controlled Study in Healthy Subjects to Assess the Safety, Tolerability, Clinical Effects, and Pharmacokinetics-Pharmacodynamics of Intravenous Cyclopropyl-methoxycarbonylmetomidate (ABP-700) after a Single Ascending Bolus Dose.

    Science.gov (United States)

    Struys, Michel M R F; Valk, Beatrijs I; Eleveld, Douglas J; Absalom, Anthony R; Meyer, Peter; Meier, Sascha; den Daas, Izaak; Chou, Thomas; van Amsterdam, Kai; Campagna, Jason A; Sweeney, Steven P

    2017-07-01

    Cyclopropyl-methoxycarbonylmetomidate (ABP-700) is a new "soft" etomidate analog. The primary objectives of this first-in-human study were to describe the safety and efficacy of ABP-700 and to determine its maximum tolerated dose. Secondary objectives were to characterize the pharmacokinetics of ABP-700 and its primary metabolite (cyclopropyl-methoxycarbonyl acid), to assess the clinical effects of ABP-700, and to investigate the dose-response and pharmacokinetic/pharmacodynamic relationships. Sixty subjects were divided into 10 cohorts and received an increasing, single bolus of either ABP-700 or placebo. Safety was assessed by clinical laboratory evaluations, infusion-site reactions, continuous monitoring of vital signs, physical examination, adverse event monitoring, and adrenocorticotropic hormone stimulation testing. Clinical effects were assessed with modified observer's assessment of alertness/sedation and Bispectral Index monitoring. Pharmacokinetic parameters were calculated. Stopping criteria were met at 1.00 mg/kg dose. No serious adverse events were reported. Adverse events were dose-dependent and comprised involuntary muscle movement, tachycardia, and ventilatory effects. Adrenocorticotropic hormone stimulation evoked a physiologic cortisol response in all subjects, no different from placebo. Pharmacokinetics were dose-proportional. A three-compartment pharmacokinetic model described the data well. A rapid onset of anesthesia/sedation after bolus administration and also a rapid recovery were observed. A quantitative concentration-effect relationship was described for the modified observer's assessment of alertness/sedation and Bispectral Index. This first-in-human study of ABP-700 shows that ABP-700 was safe and well tolerated after single-bolus injections up to 1.00 mg/kg. Bolus doses of 0.25 and 0.35 mg/kg were found to provide the most beneficial clinical effect versus side-effect profile.

  20. Photoelectrochemical control of the balance between cyclic- and linear electron transport in photosystem. I. Algorithm for P700+ induction kinetics

    NARCIS (Netherlands)

    Vredenberg, W.J.; Bulychev, A.A.

    2010-01-01

    Redox transients of chlorophyll P700, monitored as absorbance changes DeltaA810, were measured during and after exclusive PSI excitation with far-red (FR) light in pea (Pisum sativum, cv. Premium) leaves under various pre-excitation conditions. Prolonged adaptation in the dark terminated by a short

  1. Structure and tribological properties of MoCN-Ag coatings in the temperature range of 25–700 °C

    Energy Technology Data Exchange (ETDEWEB)

    Shtansky, D.V., E-mail: shtansky@shs.misis.ru [National University of Science and Technology “MISIS”, Leninsky Prospect 4, Moscow (Russian Federation); Bondarev, A.V.; Kiryukhantsev-Korneev, Ph.V. [National University of Science and Technology “MISIS”, Leninsky Prospect 4, Moscow (Russian Federation); Rojas, T.C.; Godinho, V.; Fernández, A. [Instituto de Ciencia de Materiales de Sevilla CSIC-US, Avda. Américo Vespucio 49, 41092 Sevilla (Spain)

    2013-05-15

    The preparation of hard coatings with low friction coefficient over a wide temperature range is still a challenge for the tribological community. The development of new nanocomposite materials consisting of different metal-ceramic phases, each of which exhibiting self-lubricating characteristics at different temperatures, may help to solve this problem. We report on the structure and tribological properties of MoCN-Ag coatings deposited by magnetron co-sputtering of Mo and C (graphite) targets and simultaneous sputtering of an Ag target either in pure nitrogen or in a gaseous mixture of Ar + N{sub 2}. The structure and elemental composition of the coatings were studied by means of X-ray diffraction, scanning and transmission electron microscopy, X-ray photoelectron spectroscopy, energy dispersive spectroscopy, Raman spectroscopy, and glow discharge optical emission spectroscopy. The tribological properties of the coatings against an Al{sub 2}O{sub 3} ball were investigated first at discrete temperatures of 25, 500, and 700 °C, and then during continuous heating in the temperature range of 25–700 °C. The coating structure and their respective wear tracks were also examined to elucidate their phase transformations during heat treatments. The lowest friction coefficients (<0.4) were observed in the temperature ranges of 25–100 °C and 400–700 °C and can be explained by the presence of a free amorphous carbon phase, which served as a lubricant at low temperatures, and by a positive role of silver and two phases forming at elevated temperatures, molybdenum oxide and silver molybdate, which provided lubrication above 400 °C. In the temperature range between 100 and 400 °C, the friction coefficient was relatively high. This problem is to be addressed in future works.

  2. Structure and tribological properties of MoCN-Ag coatings in the temperature range of 25–700 °C

    International Nuclear Information System (INIS)

    Shtansky, D.V.; Bondarev, A.V.; Kiryukhantsev-Korneev, Ph.V.; Rojas, T.C.; Godinho, V.; Fernández, A.

    2013-01-01

    The preparation of hard coatings with low friction coefficient over a wide temperature range is still a challenge for the tribological community. The development of new nanocomposite materials consisting of different metal-ceramic phases, each of which exhibiting self-lubricating characteristics at different temperatures, may help to solve this problem. We report on the structure and tribological properties of MoCN-Ag coatings deposited by magnetron co-sputtering of Mo and C (graphite) targets and simultaneous sputtering of an Ag target either in pure nitrogen or in a gaseous mixture of Ar + N 2 . The structure and elemental composition of the coatings were studied by means of X-ray diffraction, scanning and transmission electron microscopy, X-ray photoelectron spectroscopy, energy dispersive spectroscopy, Raman spectroscopy, and glow discharge optical emission spectroscopy. The tribological properties of the coatings against an Al 2 O 3 ball were investigated first at discrete temperatures of 25, 500, and 700 °C, and then during continuous heating in the temperature range of 25–700 °C. The coating structure and their respective wear tracks were also examined to elucidate their phase transformations during heat treatments. The lowest friction coefficients (<0.4) were observed in the temperature ranges of 25–100 °C and 400–700 °C and can be explained by the presence of a free amorphous carbon phase, which served as a lubricant at low temperatures, and by a positive role of silver and two phases forming at elevated temperatures, molybdenum oxide and silver molybdate, which provided lubrication above 400 °C. In the temperature range between 100 and 400 °C, the friction coefficient was relatively high. This problem is to be addressed in future works.

  3. Employment of MCNP in the study of TLDS 600 and 700 seeking the implementation of radiation beam characterization of BNCT facility at IEA-R1; Emprego do MCNP no estudo dos TLDS 600 e 700 visando a implementacao da caracterizacao do feixe de irradiacao da instalacao de BNCT do IEA-R1

    Energy Technology Data Exchange (ETDEWEB)

    Cavalieri, Tassio Antonio

    2013-07-01

    Boron Neutron Capture Therapy, BNCT, is a bimodal radiotherapy procedure for cancer treatment. Its useful energy comes from a nuclear reaction driven by impinging thermal neutron upon Boron 10 atoms. A BNCT research facility has been constructed in IPEN at the IEA-R1 reactor, to develop studies in this area. One of its prime experimental parameter is the beam dosimetry which is nowadays made by using activation foils, for neutron measurements, and TLD 400, for gamma dosimetry. For mixed field dosimetry, the International Commission on Radiation Units and Measurements, ICRU, recommends the use of pair of detectors with distinct responses to the field components. The TLD 600/ TLD 700 pair meets this criteria, as the amount of {sup 6}Li, a nuclide with high thermal neutron cross section, greatly differs in their composition. This work presents a series of experiments and simulations performed in order to implement the mixed field dosimetry based on the use of TLD 600/TLD 700 pair. It also intended to compare this mixed field dosimetric methodology to the one so far used by the BNCT research group of IPEN. The response of all TLDs were studied under irradiations in different irradiation fields and simulations, underwent by MCNP, were run in order to evaluate the dose contribution from each field component. Series of repeated irradiations under pure gamma field and mixed field neutron/gamma field showed differences in the TLD individual responses which led to the adoption of a Normalization Factor. It has allowed to overcome TLD selection. TLD responses due to different field components and spectra were studied. It has shown to be possible to evaluate the relative gamma/neutron fluxes from the relative responses observed in the two Regions of Interest, ROIs, from TLD 600 and TLD 700. It has also been possible to observe the TLD 700 response to neutron, which leads to a gamma dose overestimation when one follows the ICRU recommended mixed field dosimetric procedure. Dose

  4. Controlling roadside noncrop pine in SE Oklahoma using selected glyphosate formulations with and without LI 700 and Milestone VM Plus

    Science.gov (United States)

    J.L. Yeiser; M. Finke; J. Grogan

    2012-01-01

    Noncrop pine control is a major issue confronting managers of openings along roadsides and in clearcuts.Herbicides containing glyphosate are commonly used for pine control. Traditionally, managers have applied 4 quarts product/acre with inconsistent results. LI 700 is a penetrating non-ionic surfactant that contains lecithin. Selected treatments of Makaze, Accord...

  5. Mitsubishi latest coal fired USC boiler technology (CFE Pacifico 700 MW)

    Energy Technology Data Exchange (ETDEWEB)

    Hashimoto, T.; Sakamoto, K. [Mitsubishi Heavy Industries, Ltd., Nagasaki (Japan). Power Systems; Fujitab, M. [Mitsubishi Heavy Industries, Ltd., Yokohama (Japan). Power Systems

    2013-07-01

    Mitsubishi Heavy Industries, Ltd. (MHI) has successfully completed commissioning work for CFE (Comision Federal de Electricidad) Pacifico 700 MW coal-fired unit in March 2010 which is the first supercritical unit in Latin America. This supercritical boiler was designed with state of the art technologies such as low NOx burners, high fineness pulverizers, advanced vertical furnace wall technology and so on. Especially the advanced vertical furnace wall technology with some improvements is a key technology to realize swift load changes such as 5% load per minute ramping rate with assuring dynamic characteristics. Recently the requirement of the high efficiency and the swift load changes for the power boilers has been increased so that even a coal-fired unit needs flexible operation characteristics for balancing variety of power sources. One of the challenges for the swift load change is to keep the furnace wall metal temperature low during the load change, which the advanced vertical furnace wall could realize. The report describes the features of the unit and commissioning result including load swing test results in details.

  6. Employment of MCNP in the study of TLDS 600 and 700 seeking the implementation of radiation beam characterization of BNCT facility at IEA-R1

    International Nuclear Information System (INIS)

    Cavalieri, Tassio Antonio

    2013-01-01

    Boron Neutron Capture Therapy, BNCT, is a bimodal radiotherapy procedure for cancer treatment. Its useful energy comes from a nuclear reaction driven by impinging thermal neutron upon Boron 10 atoms. A BNCT research facility has been constructed in IPEN at the IEA-R1 reactor, to develop studies in this area. One of its prime experimental parameter is the beam dosimetry which is nowadays made by using activation foils, for neutron measurements, and TLD 400, for gamma dosimetry. For mixed field dosimetry, the International Commission on Radiation Units and Measurements, ICRU, recommends the use of pair of detectors with distinct responses to the field components. The TLD 600/ TLD 700 pair meets this criteria, as the amount of 6 Li, a nuclide with high thermal neutron cross section, greatly differs in their composition. This work presents a series of experiments and simulations performed in order to implement the mixed field dosimetry based on the use of TLD 600/TLD 700 pair. It also intended to compare this mixed field dosimetric methodology to the one so far used by the BNCT research group of IPEN. The response of all TLDs were studied under irradiations in different irradiation fields and simulations, underwent by MCNP, were run in order to evaluate the dose contribution from each field component. Series of repeated irradiations under pure gamma field and mixed field neutron/gamma field showed differences in the TLD individual responses which led to the adoption of a Normalization Factor. It has allowed to overcome TLD selection. TLD responses due to different field components and spectra were studied. It has shown to be possible to evaluate the relative gamma/neutron fluxes from the relative responses observed in the two Regions of Interest, ROIs, from TLD 600 and TLD 700. It has also been possible to observe the TLD 700 response to neutron, which leads to a gamma dose overestimation when one follows the ICRU recommended mixed field dosimetric procedure. Dose

  7. YAG laser in the treatment of hemorrhoids: a report of 700 cases

    Science.gov (United States)

    Liu, Jian-xun; Zhang, Xinrong

    1993-03-01

    The results of treating hemorrhoids in 700 cases with a YAG laser knife is reported. Since 1988, the author introduced the YAG laser into the treatment of various kinds of hemorrhoids. The satisfactory results were achieved with 100% cure rate. Some related problems also are discussed in this paper. Hemorrhoid is a kind of common disease. It usually appears in the superior or inferior rectal venous plexus covered with mucosa. The hemorrhoids are divided into internal, external, and mixed types according to their location and origination. The internal hemorrhoid is superior to the dentate line and caused by varicosity of superior rectal venous plexus covered with mucosa, the most common presentation is a bleeding and prolapse mass out of the anus. The external hemorrhoid arises from varicosity of inferior rectal venous plexus, the most important clinical finding is a painful mass covered with skin of the anal canal. The characteristics of mixed type are the combination of the two types as mentioned above.

  8. Disintegration of {sup 12}C nuclei by 700–1500 MeV photons

    Energy Technology Data Exchange (ETDEWEB)

    Nedorezov, V. [Institute for Nuclear Research, Russian Academy of Sciences, Prospekt 60-letiya Oktyabrya 7a, 117312 Moscow (Russian Federation); D' Angelo, A.; Bartalini, O. [Dipartimento di Fisica – Università degli Studi di Roma “Tor Vergata”, via della Ricerca Scientifica 1, I-00133 Roma (Italy); INFN – Sezione di Roma “Tor Vergata”, via della Ricerca Scientifica 1, I-00133 Roma (Italy); Bellini, V. [Dipartimento di Fisica – Università degli Studi di Catania, via Santa Sofia 64, I-95123 Catania (Italy); INFN – Sezione di Catania, via Santa Sofia 64, I-95123 Catania (Italy); Capogni, M. [Dipartimento di Fisica – Università degli Studi di Roma “Tor Vergata”, via della Ricerca Scientifica 1, I-00133 Roma (Italy); INFN – Sezione di Roma “Tor Vergata”, via della Ricerca Scientifica 1, I-00133 Roma (Italy); Casano, L.E. [INFN – Sezione di Roma “Tor Vergata”, via della Ricerca Scientifica 1, I-00133 Roma (Italy); Castoldi, M. [Dipartimento di Fisica – Università degli Studi di Genova, via Dodecaneso 33, I-16146 Genova (Italy); Curciarello, F.; De Leo, V. [Dipartimento di Fisica e di Scienze della Terra, Università di Messina, salita Sperone 31, I-98166 Messina (Italy); INFN – Sezione di Catania, via Santa Sofia 64, I-95123 Catania (Italy); Didelez, J.-P. [IN2P3, Institut de Physique Nucléaire, Rue Georges Clemenceau, F-91406 Orsay (France); and others

    2015-08-15

    Disintegration of {sup 12}C nuclei by tagged photons of 700–1500 MeV energy at the GRAAL facility has been studied by means of the LAGRANγE detector with a wide angular acceptance. The energy and momentum distributions of produced neutrons and protons as well as their multiplicity distributions were measured and compared with corresponding distributions calculated with the RELDIS model based on the intranuclear cascade and Fermi break-up models. It was found that eight fragments are created on average once per about 100 disintegration events, while a complete fragmentation of {sup 12}C into 12 nucleons is observed typically only once per 2000 events. Measured multiplicity distributions of produced fragments are well described by the model. The measured total photoabsorption cross section on {sup 12}C in the same energy range is also reported.

  9. Comparing the Structure and Mechanical Properties of Welds on Ductile Cast Iron (700 MPa under Different Heat Treatment Conditions

    Directory of Open Access Journals (Sweden)

    Ronny M. Gouveia

    2018-01-01

    Full Text Available The weldability of ductile iron, as widely known, is relatively poor, essentially due to its typical carbon equivalent value. The present study was developed surrounding the heat treatability of welded joints made with a high strength ductile cast iron detaining an ultimate tensile strength of 700 MPa, and aims to determine which heat treatment procedures promote the best results, in terms of microstructure and mechanical properties. These types of alloys are suitable for the automotive industry, as they allow engineers to reduce the thickness of parts while maintaining mechanical strength, decreasing the global weight of vehicles and providing a path for more sustainable development. The results allow us to conclude that heat treatment methodology has a large impact on the mechanical properties of welded joints created from the study material. However, the thermal cycles suffered during welding promote the formation of ledeburite areas near the weld joint. This situation could possibly be dealt through the implementation of post-welding heat treatments (PWHT with specific parameters. In contrast to a ductile cast iron tested in a previous work, the bull-eye ductile cast iron with 700 MPa ultimate tensile strength presented better results during the post-welding heat treatment than during preheating.

  10. Ocean dynamic noise energy flux directivity in the 400 Hz to 700 Hz frequency band

    Institute of Scientific and Technical Information of China (English)

    Vladimir A. Shchurov; Galina F. Ivanova; Marianna V. Kuyanova; Helen S. Tkachenko

    2007-01-01

    Results of field studies of underwater dynamic noise energy flux directivity at two wind speeds, 6 m/s and 12 m/s, in the 400 Hz to 700 Hz frequency band in the deep open ocean are presented. The measurements were made by a freely drifting telemetric combined system at 500 m depth. Statistical characteristics of the horizontal and vertical dynamic noise energy flux directivity are considered as functions of wind speed and direction. Correlation between the horizontal dynamic noise energy flux direction and that of the wind was determined; a mechanism of the horizontal dynamic noise energy flux generation is related to the initial noise field scattering on ocean surface waves.

  11. Feasibility of LTE 700 MHz Digital Dividend for Broadband Development Acceleration in Rural Areas

    Directory of Open Access Journals (Sweden)

    Denny Setiawan

    2012-04-01

    Full Text Available The need of broadband services to reduce digital divide in rural areas had increased in the recent years. The government of the Republic Indonesia shared similar intention and had set guidance of ICT development in its "economic master plan" and "medium term development plan". This paper addressed feasibility and suitability of its implementation in Indonesia, by conducting assessment of possible solutions. Using mixed method, the study was started with qualitative approach to identify possible options, conducted benchmarking and case study analysis to narrow down the options and finally conducted quantitative calculation for the two remaining options and measure performance of the solutions. The results of analysis concluded that early implementation of LTE in 700 MHz Digital Dividend would be feasible in certain geographical areas to fasten the broadband plan development in Indonesia.

  12. Feasibility of LTE 700 MHz Digital Dividend for Broadband Development Acceleration in Rural Areas

    Directory of Open Access Journals (Sweden)

    Denny Setiawan

    2013-09-01

    Full Text Available The need of broadband services to reduce digital divide in rural areas had increased in the recent years. The government of the Republic Indonesia shared similar intention and had set guidance of ICT development in its "economic master plan" and "medium term development plan". This paper addressed feasibility and suitability of its implementation in Indonesia, by conducting assessment of possible solutions. Using mixed method, the study was started with qualitative approach to identify possible options, conducted benchmarking and case study analysis to narrow down the options and finally conducted quantitative calculation for the two remaining options and measure performance of the solutions. The results of analysis concluded that early implementation of LTE in 700 MHz Digital Dividend would be feasible in certain geographical areas to fasten the broadband plan development in Indonesia.

  13. Study of the φ meson in the pp→φK10K20π+π- annihilations at 700-750 MeV/c

    International Nuclear Information System (INIS)

    Gil Lopez, E.

    1976-01-01

    We have measured the mass and width of the φ meson using the pp →π + π - K 1 0 K 2 0 annihilations at 700-750 MeV/c.- The values obtained are In good agreement with proceeding measurements. The mass has been measured with a high accuracy. (Author) 3 refs

  14. Experimental determination of the photon-energy dependent dose-to-water response of TLD600 and TLD700 (LiF:Mg,Ti) thermoluminescence detectors

    Energy Technology Data Exchange (ETDEWEB)

    Schwahofer, Andrea [Vivantes Clinic Neukoelln, Berlin (Germany). Dept. of Radiation Therapy; German Cancer Research Center, Heidelberg (Germany). Medical Physics in Radiation Therapy; Feist, Harald [Munich Univ. (Germany). Dept. of Radiation Therapy; Georg, Holger [PTW Freiburg (Germany). Calibration Lab.; Haering, Peter; Schlegel, Wolfgang [German Cancer Research Center, Heidelberg (Germany). Medical Physics in Radiation Therapy

    2017-05-01

    The aim of this study has been the experimental determination of the energy dependent dose-to-water response of TLD600 and TLD700 thermoluminescent detectors (Harshaw) in X-ray beams with mean photon energies from about 20 to 200 keV in comparison with {sup 60}Co gamma rays and 6 MV X-rays. Experiments were carried out in collaboration with the German secondary standard laboratory PTW Freiburg. The energy dependent relative responses of TLD600 and TLD700 thermoluminescence detectors were determined at radiation qualities between 30 kV{sub p} and 280 kV{sub p}. The overall uncertainty of the measured values was characterized by standard deviations varying from 1.2 to 3%. The present results agree with previous studies on the energy dependent dose-to-water response of TLD100. As an application example, the results were used to measure doses associated with X-ray imaging in image-guided radiotherapy.

  15. Influence of Alcohol and Tobacco Use on Sodium Thiopental Requirements in General Anesthesia: A Retrospective Study of 700 Patients

    OpenAIRE

    Bashir, K. R.; Raman, S.; Knott, V. J.; Bulmer, D. R.; Hurtig, J. B.

    1981-01-01

    Hospital charts of 700 patients who had undergone upper gastrointestinal surgery were reviewed to examine the relationship between alcohol abuse and dose of intravenous sodium thiopental (Pentothal) required to induce general anesthesia. Patients who required a high sodium thiopental dose (greater than 6.08 mg/kg) exhibited a higher incidence of alcoholism, heavy drinking, and heavy smoking, compared to patients who required low sodium thiopental dose (greater than 3.42 mg/kg and less than 4....

  16. Performance of MHD coatings in flowing Li at 700 deg

    International Nuclear Information System (INIS)

    Pint, B.; Pawel, S.J.; Howell, M.; Moser, J.L.; Garner, G.W.; Santella, M.L.; Tortorelli, P.F.; Di Stefano, J.R.

    2007-01-01

    Full text of publication follows: A thermal convection loop was constructed from V-4Cr-4Ti tubing and operated in vacuum at a maximum Li temperature of 700 deg. C for ∼1000 h.. Due to slow Li flow (∼1 cm/s) in the loop, the temperature gradient was ∼340 deg. C. Specimens in the hot and cold legs of the loop included V-4Cr-4Ti spacers, tensile specimens (SS-3 type) and coupons coated by physical vapor deposition with yttria and over coated with unalloyed vanadium. Based on prior work, the multi-layer electrically-insulating coatings were developed to reduce the magneto hydrodynamic (MHD) force expected in the first wall of a lithium cooled blanket in a magnetic confinement fusion reactor. Characterization of the specimens after exposure will include: (1) mass change and chemistry change as a function of location in the temperature gradient, (2) the effect of Li exposure on the tensile properties of V-4Cr-4Ti and (3) characterization of the properties and microstructure of the coatings after exposure. Of particular interest will be the coating resistivity after exposure and any degradation of the thin (∼10 μm) vanadium overlayer. Chemistry of the Li before and after the experiment will be compared in order to assess any mass transfer effects. (authors)

  17. Research and Development of Heat-Resistant Materials for Advanced USC Power Plants with Steam Temperatures of 700 °C and Above

    Directory of Open Access Journals (Sweden)

    Fujio Abe

    2015-06-01

    Full Text Available Materials-development projects for advanced ultra-supercritical (A-USC power plants with steam temperatures of 700 °C and above have been performed in order to achieve high efficiency and low CO2 emissions in Europe, the US, Japan, and recently in China and India as well. These projects involve the replacement of martensitic 9%−12% Cr steels with nickel (Ni-base alloys for the highest temperature boiler and turbine components in order to provide sufficient creep strength at 700°C and above. To minimize the requirement for expensive Ni-base alloys, martensitic 9%−12% Cr steels can be applied to the next highest temperature components of an A-USC power plant, up to a maximum of 650°C. This paper comprehensively describes the research and development of Ni-base alloys and martensitic 9%−12% Cr steels for thick section boiler and turbine components of A-USC power plants, mainly focusing on the long-term creep-rupture strength of base metal and welded joints, strength loss in welded joints, creep-fatigue properties, and microstructure evolution during exposure at elevated temperatures.

  18. Exact finite range DWBA results for the /sup 12/C(p,d)/sup 11/C reaction at 700 MeV. [Differential cross sections

    Energy Technology Data Exchange (ETDEWEB)

    Rost, E; Shepard, J R [Colorado Univ., Boulder (USA). Nuclear Physics Lab.

    1975-12-08

    The differential cross sections for the /sup 12/C(p,d)/sup 11/C(g.s.) reaction at 700 MeV have been calculated in a full finite range DWBA approach. The absolute cross sections agree with the data and are dominated by contributions arising from the deuteron D-state.

  19. Near-Infrared Phosphorus-Substituted Rhodamine with Emission Wavelength above 700 nm for Bioimaging.

    Science.gov (United States)

    Chai, Xiaoyun; Cui, Xiaoyan; Wang, Baogang; Yang, Fan; Cai, Yi; Wu, Qiuye; Wang, Ting

    2015-11-16

    Phosphorus has been successfully fused into a classic rhodamine framework, in which it replaces the bridging oxygen atom to give a series of phosphorus-substituted rhodamines (PRs). Because of the electron-accepting properties of the phosphorus moiety, which is due to effective σ*-π* interactions and strengthened by the inductivity of phosphine oxide, PR exhibits extraordinary long-wavelength fluorescence emission, elongating to the region above 700 nm, with bathochromic shifts of 140 and 40 nm relative to rhodamine and silicon-substituted rhodamine, respectively. Other advantageous properties of the rhodamine family, including high molar extinction coefficient, considerable quantum efficiency, high water solubility, pH-independent emission, great tolerance to photobleaching, and low cytotoxicity, stay intact in PR. Given these excellent properties, PR is desirable for NIR-fluorescence imaging in vivo. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Effect of temperatures up to 130 deg C on the responses of TLD 700

    Energy Technology Data Exchange (ETDEWEB)

    Douglas, J A; Binns, P J [UKAEA Atomic Energy Research Establishment, Harwell. Environmental and Medical Sciences Div.

    1984-01-01

    The need to measure doses at temperatures up to 130 deg C led to an investigation into the effect of exposure and storage at these temperatures on the response of TLD 700 before and after UV phototransfer. As a preliminary, the delays required during the UV re-estimation process were optimised. The effects of storage and exposure were compared. This was followed by a detailed examination of the effects of storage at temperatures up to 130 deg C. Glow curves were analysed to investigate the rates of growth and decay of the different peaks. The findings for peaks 6 and 7 are compatible with previously reported effects at lower temperatures on peaks 3, 4 and 5. Storage at temperatures of 130 deg C or below for periods up to 28 days does not affect the UV photo-transfer response.

  1. Q0 Degradation of LANL 700-MHZ β = 0.64 Elliptical Cavities and ANL 340 MHZ Spoke Cavities

    International Nuclear Information System (INIS)

    Tajima, Tsuyoshi; Chan, Kwok-Chi D.; Edwards, Randall L.; Gentzlinger, Robert C.; Kelley, John Patrick; Krawczyk, Frank L.; Madrid, Michael A.; Montoya, Debbie I.; Schrage, Dale L.; Shapiro, Alan H.

    2002-01-01

    The quality factor (Q 0 ) of most of the six LANL β = 0.64 700-MHz 5-cell elliptical cavities starts to drop at E acc = 8-10 MV/m, which may be related to multipacting. Residual resistances of these cavities were measured to be 5.0-7.6 n(Omega). The sensitivity of surface resistance to the external magnetic field was measured to be 0.22 n(Omega)/mG. Q disease tests have shown no significant Q 0 degradation for both elliptical cavities and a spoke cavity with our 100 (micro)m BCP.

  2. Lithic Communities of Practice and Daily life in the Northwestern Maya Lowlands during the Late Classic (700-850 A.D.)

    OpenAIRE

    Silva de la Mora, Flavio Gabriel

    2017-01-01

    This dissertation uses multiple lines of evidence to understand production, exchange and crafting in agrarian societies with a focus on the Northwestern Mayan Lowlands during the Late Classic Period (700-850 A.D). The organization of production in Pre-Columbian times is poorly understood, yet exchange is believed to be critical to the development of sociopolitical relations in ranked agrarian societies, like those in Mesoamerica. This dissertation will examine how the material culture of ever...

  3. Neutron-photon mixed field dosimetry by TLD-700 glow curve analysis and its implementation in dose monitoring for Boron Neutron Capture Therapy (BNCT) treatments

    Energy Technology Data Exchange (ETDEWEB)

    Boggio, E. F.; Longhino, J. M. [Centro Atomico Bariloche, Departamento de Fisica de Reactores y Radiaciones / CNEA, Av. E. Bustillo Km 9.5, R8402AGP San Carlos de Bariloche (Argentina); Andres, P. A., E-mail: efboggio@cab.cnea.gov.ar [Centro Atomico Bariloche, Division Proteccion Radiologica / CNEA, Av. E. Bustillo Km 9.5, R8402AGP San Carlos de Bariloche (Argentina)

    2015-10-15

    BNCT is a cancerous cells selective, non-conventional radiotherapy modality to treat malignant tumors such as glioblastoma, melanoma and recurrent head and neck cancer. It consists of a two-step procedure: first, the patient is injected with a tumor localizing drug containing a non-radioactive isotope (Boron-10) with high slow neutron capture cross-section. In a second step, the patient is irradiated with neutrons, which are absorbed by the Boron-10 agent with the subsequently nuclear reaction B- 10(n,a)Li-7, thereby resulting in dose at cellular level due to the high-Let particles. The neutron fields suitable for BNCT are characterized by high neutron fluxes and low gamma dose. Determination of each component is not an easy task, especially when the volume of measurement is quite small or inaccessible for a miniature ionization chamber, for example. A method of measuring the photon and slow neutron dose(mainly by N-14 and B-10) from the glow curve (GC) analysis of a single {sup 7}LiF thermoluminescence detector is evaluated. This method was suggested by the group headed by Dr. Grazia Gambarini. The dosemeters used were TLD-600 ({sup 6}LiF:Mg,Ti with 95.6% {sup 6}Li) and TLD-700 ({sup 7}LiF:Mg,Ti with 99.9% {sup 7}LiF) from Harshaw. Photon dose measurement using the GC analysis method with TLD-700 in mixed fields requires the relation of the two main peaks of a TLD-600 GC shape obtained from an exposition to the same neutron field, and a photon calibrated GC with TLD-700. The requirements for slow neutron dose measurements are similar. In order to properly apply the GC analysis method at the Ra-6 Research Reactor BNCT facility, measurements were carried out in a standard water phantom, fully characterized on the BNCT beam by conventional techniques (activation detectors and paired ionization chambers technique). Next, the method was implemented in whole body dose monitoring of a patient undergoing a BNCT treatment, using a Bo MAb (Bottle Manikin Absorption) phantom

  4. Safety analysis of the 700-horsepower combustion test facility

    Energy Technology Data Exchange (ETDEWEB)

    Berkey, B.D.

    1981-05-01

    The objective of the program reported herein was to provide a Safety Analysis of the 700 h.p. Combustion Test Facility located in Building 93 at the Pittsburgh Energy Technology Center. Extensive safety related measures have been incorporated into the design, construction, and operation of the Combustion Test Facility. These include: nitrogen addition to the coal storage bin, slurry hopper, roller mill and pulverizer baghouse, use of low oxygen content combustion gas for coal conveying, an oxygen analyzer for the combustion gas, insulation on hot surfaces, proper classification of electrical equipment, process monitoring instrumentation and a planned remote television monitoring system. Analysis of the system considering these factors has resulted in the determination of overall probabilities of occurrence of hazards as shown in Table I. Implementation of the recommendations in this report will reduce these probabilities as indicated. The identified hazards include coal dust ignition by hot ductwork and equipment, loss of inerting within the coal conveying system leading to a coal dust fire, and ignition of hydrocarbon vapors or spilled oil, or slurry. The possibility of self-heating of coal was investigated. Implementation of the recommendations in this report will reduce the ignition probability to no more than 1 x 10/sup -6/ per event. In addition to fire and explosion hazards, there are potential exposures to materials which have been identified as hazardous to personal health, such as carbon monoxide, coal dust, hydrocarbon vapors, and oxygen deficient atmosphere, but past monitoring experience has not revealed any problem areas. The major environmental hazard is an oil spill. The facility has a comprehensive spill control plan.

  5. In vitro kinetics of P700+ reduction of Thermosynechococcus elongatus trimeric Photosystem I complexes by recombinant cytochrome c 6 using a Joliot-type LED spectrophotometer.

    Science.gov (United States)

    Nguyen, Khoa; Vaughn, Michael; Frymier, Paul; Bruce, Barry D

    2017-01-01

    The reduction rate of photo-oxidized Photosystem I (PSI) with various natural and artificial electron donors have been well studied by transient absorption spectroscopy. The electron transfer rate from various donors to P 700 + has been measured for a wide range of photosynthetic organisms encompassing cyanobacteria, algae, and plants. PSI can be a limiting component due to tedious extraction and purification methods required for this membrane protein. In this report, we have determined the in vivo, intracellular cytochrome c 6 (cyt c 6 )/PSI ratio in Thermosynechococcus elongatus (T.e.) using quantitative Western blot analysis. This information permitted the determination of P 700 + reduction kinetics via recombinant cyt c 6 in a physiologically relevant ratio (cyt c 6 : PSI) with a Joliot-type, LED-driven, pump-probe spectrophotometer. Dilute PSI samples were tested under varying cyt c 6 concentration, temperature, pH, and ionic strength, each of which shows similar trends to the reported literature utilizing much higher PSI concentrations with laser-based spectrophotometer. Our results do however indicate kinetic differences between actinic light sources (laser vs. LED), and we have attempted to resolve these effects by varying our LED light intensity and duration. The standardized configuration of this spectrophotometer will also allow a more uniform kinetic analysis of samples in different laboratories. We can conclude that our findings from the LED-based system display an added total protein concentration effect due to multiple turnover events of P 700 + reduction by cyt c 6 during the longer illumination regime.

  6. Stirling Space Engine Program. Volume 1; Final Report

    Science.gov (United States)

    Dhar, Manmohan

    1999-01-01

    The objective of this program was to develop the technology necessary for operating Stirling power converters in a space environment and to demonstrate this technology in full-scale engine tests. Hardware development focused on the Component Test Power Converter (CTPC), a single cylinder, 12.5-kWe engine. Design parameters for the CTPC were 150 bar operating pressure, 70 Hz frequency, and hot-and cold-end temperatures of 1050 K and 525 K, respectively. The CTPC was also designed for integration with an annular sodium heat pipe at the hot end, which incorporated a unique "Starfish" heater head that eliminated highly stressed brazed or weld joints exposed to liquid metal and used a shaped-tubed electrochemical milling process to achieve precise positional tolerances. Selection of materials that could withstand high operating temperatures with long life were another focus. Significant progress was made in the heater head (Udimet 700 and Inconel 718 and a sodium-filled heat pipe); the alternator (polyimide-coated wire with polyimide adhesive between turns and a polyimide-impregnated fiberglass overwrap and samarium cobalt magnets); and the hydrostatic gas bearings (carbon graphite and aluminum oxide for wear couple surfaces). Tests on the CTPC were performed in three phases: cold end testing (525 K), engine testing with slot radiant heaters, and integrated heat pipe engine system testing. Each test phase was successful, with the integrated engine system demonstrating a power level of 12.5 kWe and an overall efficiency of 22 percent in its maiden test. A 1500-hour endurance test was then successfully completed. These results indicate the significant achievements made by this program that demonstrate the viability of Stirling engine technology for space applications.

  7. Oxidación en vapor de agua del acero inoxidable aisi 317 a 700 y 750ºc

    OpenAIRE

    MARULANDA AREVALO, JOSE LUDDEY; REMOLINA MILLAN, ADULJAY; BARON, JAIRO ALBERO

    2013-01-01

    Se realizó la oxidación del acero inoxidable austenítico AISI SAE 317, a temperaturas de 700 y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento a la corrosión. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de Microscopia Electrónica de Barrido (SEM) y difracción de rayos X (DRX), para observar cómo se forman las capas de óxidos y discutir el posible mecanismo de oxidación en vapor de agua. Se encontró que el mecanismo de...

  8. OXIDACIÓN EN VAPOR DE AGUA DEL ACERO INOXIDABLE AISI 317 A 700 Y 750ºC

    OpenAIRE

    José Luddey Marulanda Arevalo; Aduljay Remolina Millan; Jairo Alberto Barón

    2013-01-01

    Se realizó la oxidación del acero inoxidable austenítico AISI SAE 317, a temperaturas de 700 y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento a la corrosión. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de Microscopia Electrónica de Barrido (SEM) y difracción de rayos X (DRX), para observar cómo se forman las capas de óxidos y discutir el posible mecanismo de oxidación en vapor de agua. Se encontró que el mecanismo de...

  9. The Cu-Sb-Se phase system at temperatures between 350 and 700 degree C

    DEFF Research Database (Denmark)

    Karup-Møller, Sven

    1999-01-01

    Phase relations were determined in the Cu-Sb-Se phase system at 300o, 400o, 450o, 500o, 600o and 700oC. Five three-component phases are present at 300oC: permingeatite (Cu3SbSe4), phase A (Cu3SbSe3, the Se-equivalent to skinnerite Cu3SbS3), phase B (CuSbSe2, the Se-equivalent to chalcostibite Cu......SbS2), phase C (Cu5.04Sb35.9Se59.1) and phase D (Cu38.8Sb6.10Se55.1). An X-ray crystallographic study is currently in progress on phase C. Phase D is present in insufficient amounts for such a study. At 400oC phase C and D does not exist and at 500oC all solid ternary phase are absent. At 450oC two...

  10. Scanning Study of 700 Livers Evaluation of Existing Diagnostic Procedures; Etude Scintigraphique de 700 Foies (Evaluation des Procedures Actuelles de Diagnostic); Issledovanie pecheni 700 bol'nykh s pomoshch'yu skennirovaniya; Exploracion Hepatica de 700 Pacientes (Evaluacion de los Metodos Actuales De Diagnostico); Exploracion Hepatica de 700 Pacientes (Evaluacion de los Metodos Actuales de Diagnostico)

    Energy Technology Data Exchange (ETDEWEB)

    Czerniak, P. [Radium and Isotope Institute, Government Hospital, Tel-Hashomer (Israel)

    1964-10-15

    The livers of 700 patients have been examined. Clinical studies, laboratory tests, roentgenographic examinations and liver-scanning studies were performed. The patients were followed up and finally an objective diagnostic confirmation was obtained in most cases. In this way an evaluation of the performed tests was established. The liver scanning was done using Au{sup 198}, I{sup 131}-Rose Bengal and I{sup 131} PVP. Apart from the classical AP technique, special techniques were utilized, such as tri- or bi-plane stereoscanning and combined isotope studies with Au{sup 198} and I{sup 131}-Rose Bengal leading to a determination of the RLC (radioisotope liver coefficients). The patients were divided into eight clinical groups and the diagnostic data were accordingly compiled and evaluated. A summary of the results of this study is presented. Each clinical group was separately analysed. For example, a space-occupying lesion was detected in 95% of the 65 cases of Echinococcus disease. X-ray examination detected calcifications in only 35% of these cases, but also in 14% of other liver diseases. Weinberg and Casoni reactions were positive in 64% of the cases of Echinococcus, but also in 22% of other diseases. In hepatic malignancy, a space-occupying lesion was detected in 44% of cases, a foggy scan in 30% and morphological changes in 29%. In two of the 158 tumour cases the scan falsely appeared to be normal, but in 40% of the same cases the laboratory results were negative. By using the bi- and tri-plane stereoscanning technique, new and supplementary information on the state of the liver was obtained in 45% of cases. Liver scanning was also used in the follow-up study. It was found that: (1) After Echinococcotomy, a definite scar persists as a space-occupying lesion; (2) Three months after a treated amoebic abscess, complete regeneration occurs; (3) After a porto-caval shunt, the liver scan becomes smaller and the spleen larger - even when the general condition is

  11. Magnetic properties measurement of soft magnetic composite material (SOMALOY 700) by using 3-D tester

    Science.gov (United States)

    Asari, Ashraf; Guo, Youguang; Zhu, Jianguo

    2017-08-01

    Core losses of rotating electrical machine can be predicted by identifying the magnetic properties of the magnetic material. The magnetic properties should be properly measured since there are some variations of vector flux density in the rotating machine. In this paper, the SOMALOY 700 material has been measured under x, y and z- axes flux density penetration by using the 3-D tester. The calibrated sensing coils are used in detecting the flux densities which have been generated by the Labview software. The measured sensing voltages are used in obtaining the magnetic properties of the sample such as magnetic flux density B, magnetic field strength H, hysteresis loop which can be used to calculate the total core loss of the sample. The results of the measurement are analyzed by using the Mathcad software before being compared to another material.

  12. Exploring quantum mechanics a collection of 700+ solved problems for students, lecturers, and researchers

    CERN Document Server

    Galitski, Victor; Kogan, Vladimir; Galitski, Victor Jr

    2013-01-01

    A series of seminal technological revolutions has led to a new generation of electronic devices miniaturized to such tiny scales where the strange laws of quantum physics come into play. There is no doubt that, unlike scientists and engineers of the past, technology leaders of the future will have to rely on quantum mechanics in their everyday work. This makes teaching and learning the subject of paramount importance for further progress. Mastering quantum physics is a very non-trivial task and its deep understanding can only be achieved through working out real-life problems and examples. It is notoriously difficult to come up with new quantum-mechanical problems that would be solvable with a pencil and paper, and within a finite amount of time. This book remarkably presents some 700+ original problems in quantum mechanics together with detailed solutions covering nearly 1000 pages on all aspects of quantum science. The material is largely new to the English-speaking audience. The problems have been collect...

  13. 75 FR 801 - Airworthiness Directives; Rolls-Royce plc RB211-Trent 500, 700, and 800 Series Turbofan Engines

    Science.gov (United States)

    2010-01-06

    ...The FAA proposes to supersede an existing airworthiness directive (AD) for Rolls-Royce plc RB211-Trent 800 series turbofan engines. That AD currently requires replacing the fuel-to-oil heat exchanger (FOHE). This proposed AD would require replacing the FOHE on the RB211-Trent 500 and RB211-Trent 700 series turbofan engines in addition to the RB211-Trent 800 series turbofan engines. This proposed AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product, and results from the risk of engine FOHE blockage. The MCAI describes the unsafe condition as:

  14. A Novel UAS Rapid Deployment Platform for Targeted Gas Sampling and Meteorological Soundings at Altitudes up to 2,700 masl

    Science.gov (United States)

    Thomas, Rick M.; Greatwood, Colin; Richardson, Tom; Freer, Jim; MacKenzie, Rob; Brownlow, Rebecca; Lowry, David; Fisher, Rebecca E.; France, James; Nisbet, Euan G.

    2015-04-01

    This research project has developed Unmanned Aerial System (UAS) technologies for intelligent targeting and collection of atmospheric gas samples to investigate the so-called Southern Tropical Methane Anomaly, for which it is necessary to sample air below and above the trade-wind inversion. Air parcels above and below the South Atlantic trade-wind inversion can have markedly different trajectories and, hence, encounter very different methane source regions. The system is intelligent in that high resolution temperature and humidity sensors linked to the ground station characterise the atmospheric profile on the upward flight to ensure the platform targets the appropriate sample elevations on the downward trajectory. This capability has been proven to an altitude of 2,700 metres above sea level (masl; ca. 700 mb) at Ascension Island in the South Atlantic and shown that rapid and repeat deployment and sample collection is achievable. Three novel eight motor multirotor UAS (or octocopter) platforms were developed at Bristol Robotics Laboratory (BRL) using primarily off -the-shelf components with a custom-built main fuselage. Gas sampling and atmospheric sensor systems were designed by the University of Birmingham. Our paper explores the capability of this UAS and provides some initial results from the air sampling campaign conducted in September 2014. Thirty-eight sampling flights were conducted over 12 days and the resulting 47 samples analysed for their CH4 concentration using the high-precision Picarro Cavity Ring Down Spectrometer already installed at Ascension Island. A subset of samples were sent for δ13CCH4 analysis in Egham, UK. The flights were conducted up to an altitude of 2,700m with 2,000m being typical. There were no major incidents although variable zero and high wind situations above the trade wind inversion (typically at 1,800m) both presented unique challenges and required careful flight planning strategies and in flight trajectory changes. As a

  15. The dissociation mechanism and thermodynamic properties of HCl(aq) in hydrothermal fluids (to 700 °C, 60 kbar) by ab initio molecular dynamics simulations

    Science.gov (United States)

    Mei, Yuan; Liu, Weihua; Brugger, Joël; Sherman, David M.; Gale, Julian D.

    2018-04-01

    HCl is one of the most significant volatiles in the Earth's crust. It is well established that chloride activity and acidity (pH) play important roles in controlling the solubility of metals in aqueous hydrothermal fluids. Thus, quantifying the dissociation of HCl in aqueous solutions over a wide range of temperature and pressure is crucial for the understanding and numerical modeling of element mobility in hydrothermal fluids. Here we have conducted ab initio molecular dynamics (MD) simulations to investigate the mechanism of HCl(aq) dissociation and to calculate the thermodynamic properties for the dissociation reaction at 25-700 °C, 1 bar to 60 kbar, i.e. including high temperature and pressure conditions that are geologically important, but difficult to investigate via experiments. Our results predict that HCl(aq) tends to associate with increasing temperature, and dissociate with increasing pressure. In particular, HCl(aq) is highly dissociated at extremely high pressures, even at high temperatures (e.g., 60 kbar, 600-700 °C). At 25 °C, the calculated logKd values (6.79 ± 0.81) are close to the value (7.0) recommended by IUPAC (International Union of Pure and Applied Chemistry) and some previous experimental and theoretical studies (Simonson et al.., 1990; Sulpizi and Sprik, 2008, 2010). The MD simulations indicate full dissociation of HCl at low temperature; in contrast, some experiments were interpreted assuming significant association at high HCl concentrations (≥1 m HCltot) even at room T (logKd ∼0.7; e.g., Ruaya and Seward, 1987; Sretenskaya, 1992; review in Tagirov et al., 1997). This discrepancy is most likely the result of difficulties in the experimental determination of minor (if any) concentration of associated HCl(aq) under ambient conditions, and thus reflects differences in the activity models used for the interpretation of the experiments. With increasing temperature, the discrepancy between our MD results and previous experimental

  16. Microstructure and hot corrosion behaviors of two Co modified aluminide coatings on a Ni-based superalloy at 700 °C

    International Nuclear Information System (INIS)

    Fan, Q.X.; Jiang, S.M.; Yu, H.J.; Gong, J.; Sun, C.

    2014-01-01

    Highlights: • Microstructures of two Co modified NiAl coatings have been studied. • The addition of Co improves the corrosion resistance in sulfate salts at 700 °C. • For the sulfide and its eutectic of Co are more stable than those of Ni. • In chloride salts coating with medium Co content has best corrosion resistance. - Abstract: Two Co modified aluminide coatings with different Co contents were prepared by pack cementation process and above-the-pack process. The hot corrosion tests of the two coatings were performed in mixed salts of 75 wt.% Na 2 SO 4 + 25 wt.% K 2 SO 4 and 75 wt.% Na 2 SO 4 + 25 wt.% NaCl at 700 °C, with a simple aluminide coating as the reference coating. X-Ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscope (TEM) with energy dispersive X-ray spectrometer (EDS) were used to characterize the coatings and the corrosion scales. Results indicate that the addition of Co improves the hot corrosion resistance of the simple aluminide coating in the mixed sulfate salts, for the sulfide as well as its eutectic of cobalt are more stable, and possess higher melting points than those of nickel. While in the mixed salt containing chloride, the coating with medium Co content possesses the best corrosion resistance, primarily because the nitrides formed in the deposition process deteriorate the corrosion resistance of the coating with highest Co content

  17. Microstructure and hot corrosion behaviors of two Co modified aluminide coatings on a Ni-based superalloy at 700 °C

    Energy Technology Data Exchange (ETDEWEB)

    Fan, Q.X., E-mail: qxfan@imr.ac.cn; Jiang, S.M., E-mail: smjiang@imr.ac.cn; Yu, H.J.; Gong, J.; Sun, C.

    2014-08-30

    Highlights: • Microstructures of two Co modified NiAl coatings have been studied. • The addition of Co improves the corrosion resistance in sulfate salts at 700 °C. • For the sulfide and its eutectic of Co are more stable than those of Ni. • In chloride salts coating with medium Co content has best corrosion resistance. - Abstract: Two Co modified aluminide coatings with different Co contents were prepared by pack cementation process and above-the-pack process. The hot corrosion tests of the two coatings were performed in mixed salts of 75 wt.% Na{sub 2}SO{sub 4} + 25 wt.% K{sub 2}SO{sub 4} and 75 wt.% Na{sub 2}SO{sub 4} + 25 wt.% NaCl at 700 °C, with a simple aluminide coating as the reference coating. X-Ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscope (TEM) with energy dispersive X-ray spectrometer (EDS) were used to characterize the coatings and the corrosion scales. Results indicate that the addition of Co improves the hot corrosion resistance of the simple aluminide coating in the mixed sulfate salts, for the sulfide as well as its eutectic of cobalt are more stable, and possess higher melting points than those of nickel. While in the mixed salt containing chloride, the coating with medium Co content possesses the best corrosion resistance, primarily because the nitrides formed in the deposition process deteriorate the corrosion resistance of the coating with highest Co content.

  18. Identification of a novel COL1A1 frameshift mutation, c.700delG, in a Chinese osteogenesis imperfecta family

    Science.gov (United States)

    Wang, Xiran; Pei, Yu; Dou, Jingtao; Lu, Juming; Li, Jian; Lv, Zhaohui

    2015-01-01

    Osteogenesis imperfecta (OI) is a family of genetic disorders associated with bone loss and fragility. Mutations associated with OI have been found in genes encoding the type I collagen chains. People with OI type I often produce insufficient α1-chain type I collagen because of frameshift, nonsense, or splice site mutations in COL1A1 or COL1A2. This report is of a Chinese daughter and mother who had both experienced two bone fractures. Because skeletal fragility is predominantly inherited, we focused on identifying mutations in COL1A1 and COL1A2 genes. A novel mutation in COL1A1, c.700delG, was detected by genomic DNA sequencing in the mother and daughter, but not in their relatives. The identification of this mutation led to the conclusion that they were affected by mild OI type I. Open reading frame analysis indicated that this frameshift mutation would truncate α1-chain type I collagen at residue p263 (p.E234KfsX264), while the wild-type protein would contain 1,464 residues. The clinical data were consistent with the patients’ diagnosis of mild OI type I caused by haploinsufficiency of α1-chain type I collagen. Combined with previous reports, identification of the novel mutation COL1A1-c.700delG in these patients suggests that additional genetic and environmental factors may influence the severity of OI. PMID:25983617

  19. Nuclear reactors situation in Japan after the major earthquake of March 11, 2011. March 16, 2011, 7:00 PM status

    International Nuclear Information System (INIS)

    2011-01-01

    This situation note is established according to the information gained on March 16, 2011, at 7:00 PM, by the crisis centre of the French institute of radiation protection and nuclear safety (IRSN). The situation of all 6 reactors of the Fukushima I site (Dai-ichi) and of their spent fuel pools, as well as the situation of the reactors No. 1, 2, 3 and 4 of the Fukushima II site (Daini), and of the Onagawa and Tokai power plants is briefly presented with the progress of the accident management actions. (J.S.)

  20. Thermo-mechanical lifetime assessment of components for 700 °C steam turbine applications

    International Nuclear Information System (INIS)

    Ehrhardt, F.

    2014-01-01

    In order to increase thermal efficiency, steam turbine technology has been oriented to cover steam inlet temperatures above 700 °C and steam pressures exceeding 350 bar. These temperature levels require the use of nickel and cobalt based alloys. Nickel-based alloys were identified as being suitable for forgeable high-pressure steam turbine rotor materials, including welding procedures for joints between nickel-based alloys and alloyed ferritic steels. Expensive nickel-based alloys should be replaced with conventional heat-resistant steels in applications operating below ∼500-550°C. Since a welded rotor design is favoured, dissimilar metal weldments are required. The research work presented is aimed at the development of thermo-mechanical lifetime assessment methodologies for 700°C steam turbine components. The first main objective was the development of advanced creep-fatigue (CF) lifetime assessment methodologies for the evaluation of Alloy 617 steam turbine rotor features at maximum application temperatures. For the characterisation of the material behaviour under static loading conditions, creep rupture experiments for both medium temperatures and target application temperature have been conducted in order to investigate the influence of ageing treatment on Alloy 617. A creep deformation equation was developed on the basis of a modified Graham-Walles law. Continuous Low Cycle Fatigue (LCF) experiments have been performed. A plasticity model of Chaboche type has been developed. Cyclic/hold experiments have been conducted on Alloy 617. A modification on the creep law was introduced for the description of the material’s decreased creep resistance under combined CF loading. A very promising approach considering plastic and creep-dissipated energy was developed. The effectiveness of this energy exhaustion method was verified with the calculation of endurance curves for continuous cycling LCF and cyclic/hold conditions over a broad range of temperatures, strain

  1. Thermo-mechanical lifetime assessment of components for 700 °C steam turbine applications

    Energy Technology Data Exchange (ETDEWEB)

    Ehrhardt, F.

    2014-07-01

    In order to increase thermal efficiency, steam turbine technology has been oriented to cover steam inlet temperatures above 700 °C and steam pressures exceeding 350 bar. These temperature levels require the use of nickel and cobalt based alloys. Nickel-based alloys were identified as being suitable for forgeable high-pressure steam turbine rotor materials, including welding procedures for joints between nickel-based alloys and alloyed ferritic steels. Expensive nickel-based alloys should be replaced with conventional heat-resistant steels in applications operating below ∼500-550°C. Since a welded rotor design is favoured, dissimilar metal weldments are required. The research work presented is aimed at the development of thermo-mechanical lifetime assessment methodologies for 700°C steam turbine components. The first main objective was the development of advanced creep-fatigue (CF) lifetime assessment methodologies for the evaluation of Alloy 617 steam turbine rotor features at maximum application temperatures. For the characterisation of the material behaviour under static loading conditions, creep rupture experiments for both medium temperatures and target application temperature have been conducted in order to investigate the influence of ageing treatment on Alloy 617. A creep deformation equation was developed on the basis of a modified Graham-Walles law. Continuous Low Cycle Fatigue (LCF) experiments have been performed. A plasticity model of Chaboche type has been developed. Cyclic/hold experiments have been conducted on Alloy 617. A modification on the creep law was introduced for the description of the material’s decreased creep resistance under combined CF loading. A very promising approach considering plastic and creep-dissipated energy was developed. The effectiveness of this energy exhaustion method was verified with the calculation of endurance curves for continuous cycling LCF and cyclic/hold conditions over a broad range of temperatures, strain

  2. Experimental verification of Rutherford's transversal section of energies between 200 and 700 Kev

    International Nuclear Information System (INIS)

    Lara E, J.A.

    1976-01-01

    The objective was to try to verify the validity of Rutherford's transversal section, for the interval of energies between 200 and 700 Kev. It was decided to carry out this work in order to underline the fact that a great part of experiments such as: a) the use of thin films to make mirrors or produce condensers, b) the study of the composition of dielectric layers and the formation of metallic contacts with semiconductors, c) the mapping of the mass distribution at depths varying between hundreds and thousands of angstroms, d) the detection of low mass impurities on the crystal surface, e) the implantation of ions are based on the validity of Rutherford's dispersion theory, while this doesn't succeed with high energies due to the appearance of nuclear resonances, or with low energies due to the appearance of atomic effects which distort the results. The results show a standard error of approxiamately 7% with respect to the average. In conclusion, some limitations are noted in relation to the nuclei and the interval of energy; these limitations should be taken into consideration and recommendations are made about how to obtain more reliable results. (author)

  3. A 700 MHZ, 1 MW CW RF System for a FEL 100mA RF Photoinjector

    CERN Document Server

    Roybal, William; Reass, William; Rees, Daniel; Tallerico, Paul J; Torrez, Phillip A

    2005-01-01

    This paper describes a 700 MHz, 1 Megawatt CW, high efficiency klystron RF system utilized for a Free Electron Laser (FEL) high-brightness electron photoinjector (PI). The E2V klystron is mod-anode tube that operates with a beam voltage of 95 kV. This tube, operating with a 65% efficiency, requires ~96 watts of input power to produce in excess of 1 MW of output power. This output drives the 3rd cell of a 2½-cell, p-mode PI cavity through a pair of planar waveguide windows. Coupling is via a ridge-loaded tapered waveguide section and "dog-bone" iris. This paper will present the design of the RF, RF transport, coupling, and monitoring/protection systems that are required to support CW operations of the 100 mA cesiated, semi-porous SiC photoinjector.

  4. Comparison of laser welds in thick section S700 high-strength steel manufactured in flat (1G) and horizontal (2G) positions

    OpenAIRE

    Guo, Wei; Liu, Qiang; Francis, John Anthony; Crowther, Dave; Thompson, Alan; Liu, Zhu; Li, Lin

    2015-01-01

    Lack of penetration, undercut and melt sagging are common welding defects for single-pass laser welds in thick plates, particularly when using a traditional 1G welding position (laser directed towards ground). This investigation shows, for the first time, that welding 13 mm thick high-strength S700 steel plates in the 2G position (laser beam perpendicular to the direction of gravity) can mitigate some of the common welding defects including undercut and sagging. A computational fluid dynamic ...

  5. Delayed hydride cracking behavior of Zr-2.5Nb alloy pressure tubes for PHWR700

    Energy Technology Data Exchange (ETDEWEB)

    Sunil, S.; Bind, A.K.; Khandelwal, H.K.; Singh, R.N., E-mail: rnsingh@barc.gov.in; Chakravartty, J.K.

    2015-11-15

    In order to attain improved in-reactor performance few prototypes pressure tubes of Zr-2.5Nb alloy were manufactured by employing forging to break the cast structure and to obtain more homogeneous microstructure. Both double forging and single forging were employed. The forged material was further processed by employing hot extrusion, cold pilgering and autoclaving. A detailed characterization in terms of mechanical properties and microstructure of the prototype tubes were carried for qualifying it for intended use as pressure tubes in PHWR700 reactors. In this work, Delayed Hydride Cracking (DHC) behavior of the forged Zr-2.5Nb pressure tube material characterized in terms of DHC velocity and threshold stress intensity factor associated with DHC (K{sub IH}) was compared with that of conventionally manufactured material in the temperature range of 200–283 °C. Activation energy associated with the DHC in this alloy was found to be ∼60 kJ/mol for the forged materials.

  6. Preliminary results of a randomized trial comparing 400 cGy vs 700 cGy as an adjuvant to prevent heterotopic ossification after total hip arthroplasty

    International Nuclear Information System (INIS)

    Nguyen, Cam; Gupta-Burt, Shalina; Silverton, Craig; Cummings, Marilyn; Galante, Jorge O.

    1997-01-01

    Purpose/Objective: We report our preliminary results of a randomized trial comparing one single dose of 400 cGy versus 700 cGy given postoperatively in an attempt to prevent heterotopic ossification after total hip arthroplasty. Materials and Methods: From 09/1993 and 05/1996, over 800 total hip replacements were performed at our hospital. From this group of patients, 120 hips in 114 high-risk patients (14%) were enrolled in a randomized trial to determine if 400 cGy (Group A) is as efficacious as 700 cGy (Group B) in preventing heterotopic ossification. In Group A, there were 42 males (46 hips) and 12 females (12 hips) with a mean age of 60 (range 41-79); with 18 primary cementless femoral components (33%), 30 primary cemented stems (55%) and 10 revisions. In Group B, there were 30 males (32 hips) and 30 females (31 hips) with a median age of 59 (range 41-85); with 12 primary cementless femoral components (20%), 44 primary cemented stems (73%) and 6 revisions. All acetabular components were of the cementless type. Patients were randomized to receive either 400 cGy or 700 cGy in one fraction. Radiotherapy is given within 48 hours post-operatively using paired anterior and posterior fields, with blocking of the cementless acetabular component and the femoral component. Results: All 114 patients were available for a minimum follow-up of 6 months (range 6-30 months). None of the arthroplasties has failed at the latest follow-up. There were no radiation therapy complications noted. Statistical analysis revealed no difference in the distribution of patients in either group according to age, sex, primary or revision arthroplasty, cemented or cementless femoral component fixation, preoperative heterotopic ossification risk, or surgical approach. Of the 58 hips in Group A, heterotopic ossification was graded as Grade 0 in 24 hips, Grade I in 10 hips, Grade II in 18 hips, Grade III in 6 hips, with no cases of Grade IV. Of the 63 hips in Group B, heterotopic ossification was

  7. Investigations on avoidance of hot cracks during laser welding of austenitic Cr-Ni steels and nickel-based alloys using temperature field tailoring. Final report; Untersuchungen zur Vermeidung von Heissrissen beim Laserstrahlschweissen von austenitischen Cr-Ni-Staehlen und Nickelbasislegierungen mittels Temperaturfeld-Tailoring. Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-08-08

    The aim of the project was to transfer the developed method of laser beam welding of heat treated machining steels of temperature field tailoring on hot crack endangered austenitic Cr-Ni steels and nickel-based alloys. With this method, transient thermal stresses adjacent to the weld are produced by an travelling induction heating so that the hot cracking is prevented during welding. As test materials the austenitic Cr-Ni steel with sulfur additive 1.4305, the Cr-Ni steels 1.4404 and 1.4435 and the nickel-based alloy Udimet 720 were selected. As a result of the research it was shown that a hot crack-free laser welding in the investigated materials using at least three different welding and material-technical approaches is possible. [German] Das Ziel des Forschungsvorhabens bestand darin, das fuer das Laserstrahlschweissen verguetbarer Automatenstaehle entwickelte Verfahren des Temperaturfeld-Tailorings auf heissrissgefaehrdete austenitische Cr-Ni-Staehle und Nickelbasislegierungen zu uebertragen. Mit diesem Verfahren werden waehrend des Schweissens transiente thermische Spannungen neben der Schweissnaht durch eine mitlaufende induktive Erwaermung so erzeugt, dass die Heissrissbildung verhindert wird. Als Versuchswerkstoffe wurden der austenitische Cr-Ni-Stahl mit Schwefelzusatz 1.4305, die Cr-Ni-Staehle 1.4404 und 1.4435 sowie die Nickelbasislegierung Udimet 720 ausgewaehlt. Im Ergebnis des Forschungsvorhabens konnte gezeigt werden, dass ein heissrissfreies Laserstrahlschweissen bei den untersuchten Werkstoffen unter Nutzung von mindestens drei verschiedenen schweiss- und werkstofftechnischen Ansaetzen moeglich ist: Erstens koennen mit einem Temperaturfeld-Tailoring bei im Stumpfstoss zu verschweissenden Blechen aus austenitischen Staehlen bis mindestens 6 mm Dicke senkrecht zur Naht und parallel zur Blechoberflaeche wirkende transiente Druckspannungen erzeugt werden, die der Bildung von Mittelrippenrissen oder dazu parallel liegenden Heissrissen entgegenwirken

  8. Van Bebber's cyclone tracks at 700 hPa in the Eastern Alps for 1961-2002 and their comparison to circulation type classifications

    Energy Technology Data Exchange (ETDEWEB)

    Hofstaetter, Michael; Chimani, Barbara [Central Institute for Meteoroloy and Geodynamics (ZAMG), Vienna (Austria). Climate Research Dept.

    2012-10-15

    In this study, a systematic tracking of atmospheric cyclones at the pressure level of 700 hPa has been performed to determine three different track types and their climatologic characteristics over Central Europe from 1961 to 2002 by using ERA-40 (ECMWF - European Centre for Medium Range Weather Forecast, 40 year Re-Analysis) and ERA-Interim data. The specific focus is on cyclone tracks of type V as suggested by Van Bebber in 1891 and congeneric types, because of their association with extreme large-scale precipitation amounts and related flooding in Central and Eastern Europe. The tracking procedure consists of detecting isolated minima of the band-pass filtered 700 hPa geopotential height field and combining them over time to continuous tracks by nearest neighbour approach. Results show that the common Vb cyclone track is a rare event (3.5/year) and the probability of occurrence is largest in April with a secondary maximum in autumn. Furthermore, there is no temporal trend of any of these track types noticeable throughout the 42-years investigation period. The new 700 hPa cyclone track catalogue is used as a reference to verify the hypothesis of a coherence of Vb-tracks with certain circulation types (CTs). Selected objective and subjective circulation type classifications (CTCs) from COST (European Cooperation in Science and Technology) action 733 as well as a manual Vb-classification from the ZAMG (Zentralanstalt fuer Meteorologie und Geodynamik) are utilized. This study shows both the shortcomings and the potential of CTCs to discriminate Vb cyclone tracks by certain classes of stationary circulation patterns. Subjective CTCs rank higher than objective ones in terms of Brier Skill Score, which demonstrates the power to enhance relevant synoptic phenomena instead of favouring mathematical criteria. For the first time, an objective catalogue with the famous cyclone track Vb and its climatology is now on hand for the period 1961-2002, offering a valuable basis to

  9. Neutron dose measurements of Varian and Elekta linacs by TLD600 and TLD700 dosimeters and comparison with MCNP calculations.

    Science.gov (United States)

    Nedaie, Hassan Ali; Darestani, Hoda; Banaee, Nooshin; Shagholi, Negin; Mohammadi, Kheirollah; Shahvar, Arjang; Bayat, Esmaeel

    2014-01-01

    High-energy linacs produce secondary particles such as neutrons (photoneutron production). The neutrons have the important role during treatment with high energy photons in terms of protection and dose escalation. In this work, neutron dose equivalents of 18 MV Varian and Elekta accelerators are measured by thermoluminescent dosimeter (TLD) 600 and TLD700 detectors and compared with the Monte Carlo calculations. For neutron and photon dose discrimination, first TLDs were calibrated separately by gamma and neutron doses. Gamma calibration was carried out in two procedures; by standard 60Co source and by 18 MV linac photon beam. For neutron calibration by (241)Am-Be source, irradiations were performed in several different time intervals. The Varian and Elekta linac heads and the phantom were simulated by the MCNPX code (v. 2.5). Neutron dose equivalent was calculated in the central axis, on the phantom surface and depths of 1, 2, 3.3, 4, 5, and 6 cm. The maximum photoneutron dose equivalents which calculated by the MCNPX code were 7.06 and 2.37 mSv.Gy(-1) for Varian and Elekta accelerators, respectively, in comparison with 50 and 44 mSv.Gy(-1) achieved by TLDs. All the results showed more photoneutron production in Varian accelerator compared to Elekta. According to the results, it seems that TLD600 and TLD700 pairs are not suitable dosimeters for neutron dosimetry inside the linac field due to high photon flux, while MCNPX code is an appropriate alternative for studying photoneutron production.

  10. Lightweight Potential of Welded High-strength Steel Joints from S700 Under Constant and Variable Amplitude Loading by High-frequency Mechanical Impact (HFMI) Treatment

    OpenAIRE

    Yıldırım, Halid Can; Marquis, Gary; Sonsino, Cetin Morris

    2015-01-01

    Investigations with longitudinal stiffeners of the steel grade S700 under fully-reversed, constant amplitude loading and under variable amplitude loading with a straight-line spectrum show impressive fatigue strength improvement by high-frequency mechanical impact (HFMI) treatment. However, the degree of improvement was for variable amplitude loading lower when compared to constant amplitude loading due to local plasticity which occurs during larger load levels and consequently reduces the be...

  11. Microstructure and properties of 700 MPa grade HSLA steel during high temperature deformation

    International Nuclear Information System (INIS)

    Chen, Xizhang; Huang, Yuming; Lei, Yucheng

    2015-01-01

    Highlights: • Hot deformation behavior of 700 MPa HSLA steel above 1200 °C in was detailed studied. • Uniform and granular bainite is formed when the deformation amount is 40%. • Deformation resistance value under steady-equilibrium state is about 56 MPa. - Abstract: A high temperature deformation experiment was conducted on a high strength low alloy (HSLA) steel Q690 using Thermecmastor-Z thermal/physical simulator. During the experiment, the specimens were heated from room temperature to 1200 °C with the heating rate of 10 °C/s and 50 °C/s, respectively. The deformation temperature was 1200 °C and the deformation amounts were 0%, 10% and 40%, respectively. The microstructures, stress–strain diagram and hardness were obtained. The results revealed that the microstructure transformation of deformed austenite was quite different from that of the normal situation. With the increasing of deformation amount, more lath-shaped microstructure and less granulous microstructure were observed. The compressive deformation effectively prevented the precipitation of carbides. Larger deformation amount or lower heating rate was conducive to the atomic diffusion, which led to the microstructure uniformity and hardness decreasing. The maximum stress was 68.4 MPa and the steady stress was about 56 MPa

  12. ECHAUFFEMENT ET EVOLUTION STRUCTURALE D’UN ACIER XC 42 LORS D’UN ESSAI DE TORSION A 700 °C

    Directory of Open Access Journals (Sweden)

    R BENSAHA

    2001-12-01

    Full Text Available Ce travail a pour but de montrer qu'il est possible d’apprécier la température et de développer un modèle simple de calcul de la recrudescence de la température en cours de déformation pour un acier XC 42 à une température d'essai  de 700°C et pour deux vitesses de déformation généralisées différentes de 5s-1 et 30s-1.                 Cette étude prend en considération, d'une part l'enthalpie  du changement de phase a®g  qui se libère au cours de la déformation dans l'intervalle de température A1-A3, et d'autre part, des mécanismes thermiquement activées (restauration et recristallisation dynamique mis en jeu lors de la déformation du matériau. Comme nos essais étaient pratiqués à la température de 700°C, proche de celle du point de transformation A1, les structures obtenues après trempe rapide montrent bien que pendant la déformation le matériau a subi la transformation de phase a®g, provoquée par l'auto échauffement de l'acier XC42. Le degré d'austénitisation est donc fonction de l'auto échauffement du matériau qui, à grande vitesse de déformation (227°C, est plus important qu'à faible vitesse (142°C.

  13. Toxicity of glyphosate as Glypro and LI700 to red-eared slider (trachemys scripta elegans) embryos and early hatchlings.

    Science.gov (United States)

    Sparling, Donald W; Matson, Cole; Bickham, John; Doelling-Brown, Paige

    2006-10-01

    More than 8.2 billion ha of cropland, gardens, and forests are treated with the herbicide glyphosate each year. Whereas the toxicity of glyphosate and associated adjuvants has been measured in other vertebrates, few, if any, studies have looked at their effects in reptiles. In some instances, management of turtle habitat requires control of successional stages through application of herbicides. Adults and juvenile turtles may be exposed directly, whereas embryos may contact the chemicals through the soil. In the present study, we exposed eggs of red-eared sliders (Trachemys scripta elegans) to single applications of herbicide ranging from 0 to 11,206 ppm wet weight of glyphosate in Glypro and 0 to 678 ppm of the surfactant, LI700. Hatching success at the highest concentration was significantly lower (73%) than in other treatments (80-100%). At hatch, turtles at the highest concentration weighed less than those at other concentrations. During a 14-d holding period, we observed dose-response relationships in the ability of hatchlings to right themselves when turned on their backs. At the end of the holding period, hatchlings at the highest dose level were still lighter, and somatic indices were lower, than those in other treatments. Genetic damage, as measured by flow cytometry, increased with treatment concentration except for the highest dose. We conclude that because of the high concentrations needed to produce effects and the protection offered by several centimeters of soil or sediment, glyphosate with LI700 poses low levels of risk to red-eared slider embryos under normal field operations with regards to the endpoints measured in the present study. Carelessness in handling glyphosate or failure to follow label directions may produce adverse effects. There also is a risk that the health of turtle embryos may be affected in ways not measured in the present study.

  14. A revised dosimetric characterization of the model S700 electronic brachytherapy source containing an anode-centering plastic insert and other components not included in the 2006 model.

    Science.gov (United States)

    Hiatt, Jessica R; Davis, Stephen D; Rivard, Mark J

    2015-06-01

    The model S700 Axxent electronic brachytherapy source by Xoft, Inc., was characterized by Rivard et al. in 2006. Since then, the source design was modified to include a new insert at the source tip. Current study objectives were to establish an accurate source model for simulation purposes, dosimetrically characterize the new source and obtain its TG-43 brachytherapy dosimetry parameters, and determine dose differences between the original simulation model and the current model S700 source design. Design information from measurements of dissected model S700 sources and from vendor-supplied CAD drawings was used to aid establishment of an updated Monte Carlo source model, which included the complex-shaped plastic source-centering insert intended to promote water flow for cooling the source anode. These data were used to create a model for subsequent radiation transport simulations in a water phantom. Compared to the 2006 simulation geometry, the influence of volume averaging close to the source was substantially reduced. A track-length estimator was used to evaluate collision kerma as a function of radial distance and polar angle for determination of TG-43 dosimetry parameters. Results for the 50 kV source were determined every 0.1 cm from 0.3 to 15 cm and every 1° from 0° to 180°. Photon spectra in water with 0.1 keV resolution were also obtained from 0.5 to 15 cm and polar angles from 0° to 165°. Simulations were run for 10(10) histories, resulting in statistical uncertainties on the transverse plane of 0.04% at r = 1 cm and 0.06% at r = 5 cm. The dose-rate distribution ratio for the model S700 source as compared to the 2006 model exceeded unity by more than 5% for roughly one quarter of the solid angle surrounding the source, i.e., θ ≥ 120°. The radial dose function diminished in a similar manner as for an (125)I seed, with values of 1.434, 0.636, 0.283, and 0.0975 at 0.5, 2, 5, and 10 cm, respectively. The radial dose function ratio between the current

  15. Species-specific differences of the spectroscopic properties of P700 - Analysis of the influence of non-conserved amino acid residues by site-directed mutagenesis of photosystem I from Chlamydomonas reinhardtii

    NARCIS (Netherlands)

    Witt, H.; Bordignon, E.; Carbonera, D.; Dekker, J.P.; Karapetyan, N.; Teutloff, C.; Webber, A.; Lubitz, W.; Schlodder, E.

    2003-01-01

    We applied optical spectroscopy, magnetic resonance techniques, and redox titrations to investigate the properties of the primary electron donor P700 in photosystem I (PS I) core complexes from cyanobacteria (Thermosynechococcus elongatus, Spirulina platensis, and Synechocystis sp. PCC 6803), algae

  16. Simultaneous quantum dash-well emission in a chirped dash-in-well superluminescent diode with spectral bandwidth >700 nm

    KAUST Repository

    Khan, Mohammed Zahed Mustafa

    2013-10-01

    We report on the quantitative evidence of simultaneous amplified spontaneous emission from the AlGaInAs/InAs/ InP-based quantum-well (Qwell) and quantum-dashes (Qdash) in a multistack dash-in-an-asymmetric-well superluminescent diode heterostructure. As a result, an emission bandwidth (full width at half-maximum) of 700 nm is achieved, covering entire O-E-S-C-L-U communication bands, and a maximum continuous wave output power of 1.3 mW, from this device structure. This demonstration paves a way to bridge entire telecommunication bands through proper optimization of device gain region, bringing significant advances and impact to a variety of cross-disciplinary field applications. © 2013 Optical Society of America.

  17. Simultaneous quantum dash-well emission in a chirped dash-in-well superluminescent diode with spectral bandwidth >700 nm

    KAUST Repository

    Khan, Mohammed Zahed Mustafa; Cha, Dong Kyu; Majid, Mohammed Abdul; Ng, Tien Khee; Ooi, Boon S.

    2013-01-01

    We report on the quantitative evidence of simultaneous amplified spontaneous emission from the AlGaInAs/InAs/ InP-based quantum-well (Qwell) and quantum-dashes (Qdash) in a multistack dash-in-an-asymmetric-well superluminescent diode heterostructure. As a result, an emission bandwidth (full width at half-maximum) of 700 nm is achieved, covering entire O-E-S-C-L-U communication bands, and a maximum continuous wave output power of 1.3 mW, from this device structure. This demonstration paves a way to bridge entire telecommunication bands through proper optimization of device gain region, bringing significant advances and impact to a variety of cross-disciplinary field applications. © 2013 Optical Society of America.

  18. Detection and identification of 700 drugs by multi-target screening with a 3200 Q TRAP LC-MS/MS system and library searching.

    Science.gov (United States)

    Dresen, S; Ferreirós, N; Gnann, H; Zimmermann, R; Weinmann, W

    2010-04-01

    The multi-target screening method described in this work allows the simultaneous detection and identification of 700 drugs and metabolites in biological fluids using a hybrid triple-quadrupole linear ion trap mass spectrometer in a single analytical run. After standardization of the method, the retention times of 700 compounds were determined and transitions for each compound were selected by a "scheduled" survey MRM scan, followed by an information-dependent acquisition using the sensitive enhanced product ion scan of a Q TRAP hybrid instrument. The identification of the compounds in the samples analyzed was accomplished by searching the tandem mass spectrometry (MS/MS) spectra against the library we developed, which contains electrospray ionization-MS/MS spectra of over 1,250 compounds. The multi-target screening method together with the library was included in a software program for routine screening and quantitation to achieve automated acquisition and library searching. With the help of this software application, the time for evaluation and interpretation of the results could be drastically reduced. This new multi-target screening method has been successfully applied for the analysis of postmortem and traffic offense samples as well as proficiency testing, and complements screening with immunoassays, gas chromatography-mass spectrometry, and liquid chromatography-diode-array detection. Other possible applications are analysis in clinical toxicology (for intoxication cases), in psychiatry (antidepressants and other psychoactive drugs), and in forensic toxicology (drugs and driving, workplace drug testing, oral fluid analysis, drug-facilitated sexual assault).

  19. Digestible methionine + cystine requirement for Nile tilapia from 550 to 700 g

    Directory of Open Access Journals (Sweden)

    Mariana Michelato

    2013-01-01

    Full Text Available This trial was conducted to determine the dietary digestible methionine + cystine requirement of Nile tilapia (550 to 700 g based on the ideal protein concept. Six hundred fish were distributed in a completely randomized design with five treatments and four replicates, with 30 fish per experimental unit. The fish were fed diets containing approximately 262 g of digestible protein/kg, 3,040 kcal of digestible energy/kg and 7.90, 9.40, 10.90, 12.40 or 13.90 g of methionine + cystine/kg. The fish were hand-fed three times a day until apparent satiation for 30 days. No effects of dietary methionine + cystine on feed conversion ratio, daily protein deposition, whole body moisture, fillet moisture, crude protein, ether extract and ash, plasmatic HDL and LDL cholesterol were observed. Dietary methionine resulted in a linear increase in whole body protein and linear reduction in lipid deposition rate, hepatosomatic index, whole body ether extract and ash, plasmatic total cholesterol, plasmatic total lipids and plasmatic triglycerides. According to the Linear Response Plateau, the daily weight gain and fillet yield increased up to a level of 9.00 and 9.90 g methionine + cystine/kg of diet, respectively. The digestible methionine + cystine requirement of Nile tilapia is 9.00 g/kg for weight gain and 9.90 g/kg for fillet yield, corresponding to methionine + cystine:lysine ratios of 0.60 and 0.66, respectively.

  20. Mathematical modelling of heat absorption capacity of containment spray system in a 700 MWe PHWR

    International Nuclear Information System (INIS)

    Kota, Sampath Bharadwaj; Ali, Seik Mansoor; Balasubramaniyan, V.

    2015-01-01

    This paper presents a mathematical model for estimating the heat removal by containment spray system in the post Loss of Coolant Accident (LOCA) environment. The procedure involves firstly, the calculation of heat removal rates by droplets of spray dispersed in the air-steam mixture by an appropriate direct contact condensation model accounting for the presence of non-condensable gas (air). Parametric influence of droplet size, ambient pressure and temperature on heat flux is brought out. It was found that the heat flux is inversely proportional to the ambient pressure and diameter. A spray module was subsequently developed and incorporated into an in-house containment thermal hydraulics code. The pressure and temperature transients in a 700 MWe PHWR containment building following a Large Break LOCA was obtained using this code. The efficacy of the spray in condensing the steam is shown by comparing the transients with and without the operation of spray system. Parametric studies are also conducted with respect to droplet size and flow rate of water droplet spray. The details of the investigation are presented and discussed in this paper. (author)

  1. SU-E-T-284: Revisiting Reference Dosimetry for the Model S700 Axxent 50 KVp Electronic Brachytherapy Source

    International Nuclear Information System (INIS)

    Hiatt, JR; Rivard, MJ

    2014-01-01

    Purpose: The model S700 Axxent electronic brachytherapy source by Xoft was characterized in 2006 by Rivard et al. The source design was modified in 2006 to include a plastic centering insert at the source tip to more accurately position the anode. The objectives of the current study were to establish an accurate Monte Carlo source model for simulation purposes, to dosimetrically characterize the new source and obtain its TG-43 brachytherapy dosimetry parameters, and to determine dose differences between the source with and without the centering insert. Methods: Design information from dissected sources and vendor-supplied CAD drawings were used to devise the source model for radiation transport simulations of dose distributions in a water phantom. Collision kerma was estimated as a function of radial distance, r, and polar angle, θ, for determination of reference TG-43 dosimetry parameters. Simulations were run for 10 10 histories, resulting in statistical uncertainties on the transverse plane of 0.03% at r=1 cm and 0.08% at r=10 cm. Results: The dose rate distribution the transverse plane did not change beyond 2% between the 2006 model and the current study. While differences exceeding 15% were observed near the source distal tip, these diminished to within 2% for r>1.5 cm. Differences exceeding a factor of two were observed near θ=150° and in contact with the source, but diminished to within 20% at r=10 cm. Conclusions: Changes in source design influenced the overall dose rate and distribution by more than 2% over a third of the available solid angle external from the source. For clinical applications using balloons or applicators with tissue located within 5 cm from the source, dose differences exceeding 2% were observed only for θ>110°. This study carefully examined the current source geometry and presents a modern reference TG-43 dosimetry dataset for the model S700 source

  2. Long-term corrosion tests of Ti{sub 3}SiC{sub 2} and Ti{sub 2}AlC in oxygen containing LBE at temperatures up to 700 °C

    Energy Technology Data Exchange (ETDEWEB)

    Heinzel, A., E-mail: Annette.heinzel@kit.edu; Weisenburger, A.; Müller, G.

    2016-12-15

    Two MAX-phase materials, Ti{sub 3}SiC and Ti{sub 2}AlC, were tested at 550 °C, 650 °C and 700 °C up to 10 000 h in LBE (lead-bismuth-eutectic) containing of 10{sup −6} and 10{sup −8} wt% oxygen. It was found that secondary phases have a strong influence on corrosion effects. Ti{sub 3}SiC showed a surface disintegration at 550°C/10{sup −6} wt% oxygen after longer exposure, while a 4–7 μm thick TiO{sub 2} layer with Pb-Bi inclusions was detected on Ti{sub 2}AlC. However, Ti{sub 3}SiC is protected by a double layered oxide with an outer part of TiO{sub 2} and a mixed inner layer of SiO{sub 2} and TiO{sub 2} at the higher temperatures. Ti{sub 2}AlC formed a TiO{sub 2} surface layer containing Al{sub 2}O{sub 3}. Some defects could be observed on the Ti{sub 3}SiC surface in LBE containing 10{sup −8} wt% oxygen at 550 °C and 650 °C. The secondary phases between the Ti{sub 3}SiC grains showed strong oxidation at 700 °C. Due to the high Al solubility in LBE, Ti{sub 2}AlC experienced strong dissolution attack after longer exposure times at 650 and 700 °C.

  3. Using the PSCPCSP computer software for optimization of the composition of industrial alloys and development of new high-temperature nickel-base alloys

    Science.gov (United States)

    Rtishchev, V. V.

    1995-11-01

    Using computer programs some foreign firms have developed new deformable and castable high-temperature nickel-base alloys such as IN, Rene, Mar-M, Udimet, TRW, TM, TMS, TUT, with equiaxial, columnar, and single-crystal structures for manufacturing functional and nozzle blades and other parts of the hot duct of transport and stationary gas-turbine installations (GTI). Similar investigations have been carried out in Russia. This paper presents examples of the use of the PSCPCSP computer software for a quantitative analysis of structural und phase characteristics and properties of industrial alloys with change (within the grade range) in the concentrations of the alloying elements for optimizing the composition of the alloys and regimes of their heat treatment.

  4. A genome or a memome? : the cause of the rise of Pteridium esculentum at c. 700 BP in pollen/spore records from Aotearoa/New Zealand

    International Nuclear Information System (INIS)

    Flenley, J.; Todd, A.

    2001-01-01

    In New Zealand palynology, a strong increase in abundance of the spores of Pteridium esculentum (the bracken fern) about 700 BP has been taken by some authors to be an indication of first colonisation by people. Earlier dates for this phenomenon have been rejected by these authors. In this paper we argue that rejection of these dates may be inappropriate. A preliminary statistical analysis shows that early dates tend to be near sea level, in climatically favourable areas, close to the coast or to navigable rivers, and in the north. This does not conflict with an early arrival of people and progressive spread later. To explain the fact that most inland, upland, climatically unfavourable and southern dates cluster around 700 BP, an alternative hypothesis is advanced: that it represents the establishment of the use of the bracken fern rhizome as a staple diet, allowing rapid expansion into areas virtually uninhabitable previously because of lack of a suitable crop. On this hypothesis it was the spread through an existing population of the memome (set of ideas) about fern use which caused the palynological change, not the spread of the genome (the human species). An analogy is drawn with the spread of agriculture into Western Europe in Neolithic times. (author). 41 refs., 5 figs., 2 tabs

  5. Oxidation-induced embrittlement and structural changes of Zircaloy-4 tubing in steam at 700-1000 deg. C

    Energy Technology Data Exchange (ETDEWEB)

    Ali, A E; Huessein, A G; El-Sayed, A A; El Banna, O A [Atomic Energy Authority, Cairo (Egypt); El Raghy, S M [Cairo Univ. (Egypt). Faculty of Engineering

    1997-02-01

    The oxidation-induced embrittlement and structural changes of Zircaloy-4 (KWU-Type) tubing was investigated under light water reactors (LWR) Loss-of-Coolant. Accident conditions (LOCA) in temperature range 700-1000 deg. C. The effect of hydrogen addition to steam was also investigated in the temperature range 800-1000 deg. C. The oxidation-induced embrittlement was found to be a function of both temperature and time. Fractography investigation of oxidized tubing showed a typical brittle fracture in the stabilized-alpha zone. The microhardness measurements revealed that the alpha-Zr is harder than that near the mid-wall position. The oxidation-induced embrittlement at 900 deg. C was found to be higher than at 1000 deg. C. The results also indicated that the addition of 5% by volume hydrogen to steam resulted in an increase in the degree of embrittlement. (author). 22 refs, 9 figs, 3 tabs.

  6. Energy Provisions of the ICC-700, LEED for Homes, and ENERGY STAR Mapped to the 2009 IECC

    Energy Technology Data Exchange (ETDEWEB)

    Britt, Michelle L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Sullivan, Robin S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kora, Angela R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Makela, Eric J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Makela, Erin [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2011-05-01

    This document provides the results of a comparison of building energy efficient elements of the ICC-700 National Green Building Standard, LEED for Homes, and ENERGY STAR versions 2, 2.5, and 3.0 to the 2009 International Energy Conservation Code (2009 IECC). This comparison will provide a tool for states and local municipalities as they consider adoption of these programs. The comparison is presented in a series of appendices. The first appendix provides a summary chart that visually represents the comprehensive comparison of the programs to the 2009 IECC topic areas. Next there are a series of individual tables (one appendix for each program) that include the specific program mapping to the 2009 IECC elements with comments that briefly discuss how well the elements mapped. Finally, a comprehensive table is included that shows all five of the programs mapped to the 2009 IECC elements to allow a detailed comparison.

  7. Acidity of cations and the solubility of oxides in the eutectic KCl-LiCl melt at 700 Deg C

    International Nuclear Information System (INIS)

    Cherginets, V.L.; Rebrova, T.P.

    1999-01-01

    Products of MgO, NiO and CoO solubility in KCl-LiCl melt at 700 Deg C were determined by the method of potentiometric titration using Pt(O 2 )IZrO 2 (Y 2 O 3 ) membrane oxygen electrode. It was ascertained that acid properties of Cd 2+ and Pb'2 + cations are levelled to Li + properties, a break in E-pO graduation dependence in KCl-LiCl melt was observed at pO ∼ 2. Increase in oxides solubility in the melt studied compared with KCl-NaCl and CsCl-KCl-NaCl melts stems from the presence of Li + cations in the melt studied, which possess stronger acid properties than those of Na + or K + [ru

  8. A revised dosimetric characterization of the model S700 electronic brachytherapy source containing an anode-centering plastic insert and other components not included in the 2006 model

    International Nuclear Information System (INIS)

    Hiatt, Jessica R.; Davis, Stephen D.; Rivard, Mark J.

    2015-01-01

    Purpose: The model S700 Axxent electronic brachytherapy source by Xoft, Inc., was characterized by Rivard et al. in 2006. Since then, the source design was modified to include a new insert at the source tip. Current study objectives were to establish an accurate source model for simulation purposes, dosimetrically characterize the new source and obtain its TG-43 brachytherapy dosimetry parameters, and determine dose differences between the original simulation model and the current model S700 source design. Methods: Design information from measurements of dissected model S700 sources and from vendor-supplied CAD drawings was used to aid establishment of an updated Monte Carlo source model, which included the complex-shaped plastic source-centering insert intended to promote water flow for cooling the source anode. These data were used to create a model for subsequent radiation transport simulations in a water phantom. Compared to the 2006 simulation geometry, the influence of volume averaging close to the source was substantially reduced. A track-length estimator was used to evaluate collision kerma as a function of radial distance and polar angle for determination of TG-43 dosimetry parameters. Results for the 50 kV source were determined every 0.1 cm from 0.3 to 15 cm and every 1° from 0° to 180°. Photon spectra in water with 0.1 keV resolution were also obtained from 0.5 to 15 cm and polar angles from 0° to 165°. Simulations were run for 10 10 histories, resulting in statistical uncertainties on the transverse plane of 0.04% at r = 1 cm and 0.06% at r = 5 cm. Results: The dose-rate distribution ratio for the model S700 source as compared to the 2006 model exceeded unity by more than 5% for roughly one quarter of the solid angle surrounding the source, i.e., θ ≥ 120°. The radial dose function diminished in a similar manner as for an 125 I seed, with values of 1.434, 0.636, 0.283, and 0.0975 at 0.5, 2, 5, and 10 cm, respectively. The radial dose function

  9. A revised dosimetric characterization of the model S700 electronic brachytherapy source containing an anode-centering plastic insert and other components not included in the 2006 model

    Energy Technology Data Exchange (ETDEWEB)

    Hiatt, Jessica R. [Department of Radiation Oncology, Rhode Island Hospital, The Warren Alpert Medical School of Brown University, Providence, Rhode Island 02903 (United States); Davis, Stephen D. [Department of Medical Physics, McGill University Health Centre, Montreal, Quebec H3G 1A4 (Canada); Rivard, Mark J., E-mail: mark.j.rivard@gmail.com [Department of Radiation Oncology, Tufts University School of Medicine, Boston, Massachusetts 02111 (United States)

    2015-06-15

    Purpose: The model S700 Axxent electronic brachytherapy source by Xoft, Inc., was characterized by Rivard et al. in 2006. Since then, the source design was modified to include a new insert at the source tip. Current study objectives were to establish an accurate source model for simulation purposes, dosimetrically characterize the new source and obtain its TG-43 brachytherapy dosimetry parameters, and determine dose differences between the original simulation model and the current model S700 source design. Methods: Design information from measurements of dissected model S700 sources and from vendor-supplied CAD drawings was used to aid establishment of an updated Monte Carlo source model, which included the complex-shaped plastic source-centering insert intended to promote water flow for cooling the source anode. These data were used to create a model for subsequent radiation transport simulations in a water phantom. Compared to the 2006 simulation geometry, the influence of volume averaging close to the source was substantially reduced. A track-length estimator was used to evaluate collision kerma as a function of radial distance and polar angle for determination of TG-43 dosimetry parameters. Results for the 50 kV source were determined every 0.1 cm from 0.3 to 15 cm and every 1° from 0° to 180°. Photon spectra in water with 0.1 keV resolution were also obtained from 0.5 to 15 cm and polar angles from 0° to 165°. Simulations were run for 10{sup 10} histories, resulting in statistical uncertainties on the transverse plane of 0.04% at r = 1 cm and 0.06% at r = 5 cm. Results: The dose-rate distribution ratio for the model S700 source as compared to the 2006 model exceeded unity by more than 5% for roughly one quarter of the solid angle surrounding the source, i.e., θ ≥ 120°. The radial dose function diminished in a similar manner as for an {sup 125}I seed, with values of 1.434, 0.636, 0.283, and 0.0975 at 0.5, 2, 5, and 10 cm, respectively. The radial dose

  10. Power supply for 700 MeV booster ring dipole and quadrupole magnets

    International Nuclear Information System (INIS)

    Thipsay, A.P.; Kotaiah, S.; Ramamurthi, S.S.

    1993-01-01

    The power supply to energize main coils of the booster dipole and quadrupole magnets which are connected in series is discussed. The current in this coils is increased from 28.6 Amps at injection energy (20 MeV) to 1000 Amps at the extraction energy (700 MeV) in 0.2 sec with a stability of 0.1%. Current is maintained at 1000 Amps for 0.05 to 0.166 sec with 0.02% stability after which the current is brought down fast to the injection energy level to get the required repetition rate of 2 Hz. The rectifier stage uses four fully controlled thyristorised bridges connected in series which are switched selectively at different times to get the required trapezoidal current waveform. In the ramp down period, all the bridges are operated in the inverter mode, whereby the stored energy in the magnets is fed back to the mains. An inductor and a capacitor is used as a passive filter to attenuate the voltage ripple to the rectifier. Two capacitor banks in the passive filter are switched selectively while ramping and flat top periods to reduce the error in current within tolerable limits. An active filter is used to further reduce ripple current in magnets. The current control circuit is characterized by two loops, one with voltage feedback and the other with a current feedback. A feed forward correction is also given in the voltage feedback loop to account for the charge in the inductance of the magnets at different current levels. (author). 2 figs

  11. Mechanical properties of Zr-2.5Nb pressure tube material manufactured employing forging routes for PHWR700 - Part 1: tensile behavior

    International Nuclear Information System (INIS)

    Bind, A.K.; Singh, R.N.; Sunil, Saurav; Chakravartty, J.K.; Ghosh, Agnish; Dhandharia, Priyesh; More, Nitin S.; Vijayakumar, S.; Chhatre, A.G.

    2012-01-01

    Tensile properties of Zr-2.5Nb alloy tubes produced employing forging to break the cast structure were evaluated by carrying out uni-axial tension test at temperatures between 25 and 325 degC and under strain-rate of 1.075 x 10 -4 /s for both longitudinal and transverse specimens. Both strength and elongation values were comparable for the samples obtained from front and back end of the tube. Transverse samples showed higher strength and lower uniform elongation values as compared to longitudinal samples. The yield strength of double forged material at 25 degC is higher than the PHWR700 specification of a maximum value of 586 MPa. (author)

  12. 700 W blue fiber-coupled diode-laser emitting at 450 nm

    Science.gov (United States)

    Balck, A.; Baumann, M.; Malchus, J.; Chacko, R. V.; Marfels, S.; Witte, U.; Dinakaran, D.; Ocylok, S.; Weinbach, M.; Bachert, C.; Kösters, A.; Krause, V.; König, H.; Lell, A.; Stojetz, B.; Löffler, A.; Strauss, U.

    2018-02-01

    A high-power blue laser source was long-awaited for processing materials with low absorption in the near infrared (NIR) spectral range like copper or gold. Due to the huge progress of GaN-based semiconductors, the performance of blue diode-lasers has made a major step forward recently. With the availability of unprecedented power levels at cw-operating blue diode-lasers emitting at 450 nm, it was possible to set up a high-power diode-laser in the blue spectral range to address these conventional laser applications and probably beyond that to establish completely new utilizations for lasers. Within the scope of the research project "BlauLas", funded within the German photonic initiative "EFFILAS" [8] by the German Federal Ministry of Education and Research (BMBF), Laserline in cooperation with OSRAM aims to realize a cw fiber-coupled diode-laser exceeding 1 kW blue laser power. In this paper the conceptual design and experimental results of a 700 W blue fiber-coupled diode-laser are presented. Initially a close look had to be taken on the mounting techniques of the semiconductors to serve the requirements of the GaN laser diodes. Early samples were used for extensive long term tests to investigate degradation processes. With first functional laser-modules we set up fiber-coupled laser-systems for further testing. Besides adaption of well-known optical concepts a main task within the development of the laser system was the selection and examination of suitable materials and assembling in order to minimize degradation and reach adequate lifetimes. We realized R&D blue lasersystems with lifetimes above 5,000 h, which enable first application experiments on processing of various materials as well as experiments on conversion to white-light.

  13. Oxidation limited lifetime of Ni-Base metal foams in the temperature range 700-900 C

    Energy Technology Data Exchange (ETDEWEB)

    Chyrkin, Anton; Singheiser, Lorenz; Quadakkers, Willem Joseph [Forschungszentrum Juelich GmbH, IEF-2, Juelich (Germany); Schulze, Sebastian Leif; Bleck, Wolfgang [Department of Ferrous Metallurgy, RWTH Aachen University, Aachen (Germany); Piron-Abellan, Javier [Vallourec Mannesmann Tubes, Duesseldorf (Germany)

    2010-09-15

    INCONEL 625 metal foams produced from alloy powder by the slip-reaction-foam-sinter-process are tested in respect to cyclic oxidation behavior in air in the temperature range 700-900 C. The structure of the oxide scales formed on the foam particles is characterized using optical microscopy and SEM/EDX analysis. Main emphasis is put on studying the oxidation limited lifetimes of the foams as function of temperature and foam microstructure. It is shown that mechanical disintegration during long term oxidation at the highest test temperatures is caused by a critical depletion of the Cr content in the alloy as a result of the growth of the initially formed surface chromia layer. This results in chemical breakaway due to accelerated oxide growth of voluminous Ni-rich oxide on chromium exhausted alloy particles. Lifetime modeling based on calculation of Cr-depletion in the alloy at the oxide/metal interface of each individual foam particle using the DICTRA software is in good agreement with the experimentally determined values of the time to breakaway. (Copyright copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  14. Re-Design Pompa Sentrifugal Double Admission dengan Fluida Kerja Semi Lean Benfield Solution (K2CO3 pada Kapasitas 700 m3/h dan Head 275.8 m, (STUDI KASUS : PT. PETROKIMIA GRESIK

    Directory of Open Access Journals (Sweden)

    Fathur Rahim

    2013-09-01

    Full Text Available Penggunaan pompa sentrifugal dalam dunia industri, khususnya di PT. Petrokimia Gresik memiliki peran yang sangat penting, terutama untuk memindahkan fluida kerja dari satu tempat ke tempat lain. PT. Petrokima Gresik dalam menggunakan jenis pompa untuk mengalirkan semi lean benfield solution ( yang berfungsi sebagai absorber dalam proses pembuatan amoniak. Seiring berjalannya waktu, kapasitas pompa sentrifugal double admission yang semula 582,3ingin ditingkatkan menjadi 700 Oleh karena itu, dilakukan perancangan ulang pompa sentrifugal double admission untuk fluida kerja semi lean benfield solution ( .Setelah itu dilakukan perancangan ulang pompa dengan data yang telah diolah meliputi perancangan poros, impeller dengan bentuk sudu double curvature, volute, pasak dan bearing. Dari perancangan ulang, didapatkan desain pompa sentrifugal double admission untuk fluida kerja semi lean benfield solution ( yang sesuai dengan kapasitas 700pada head 275,8 m serta daya BHP sebesar 886 Kwatt dengan effisiensi 74%.

  15. Oxidation of (Cr,Ti)_2AlC Compounds at 700-1000 °C for One Year in Air

    International Nuclear Information System (INIS)

    Lee, Jae Chun; Won, Sung Bin; Lee, Dong Bok; Park, Sang Whan

    2013-01-01

    (Cr,Ti)_2AlC compounds were synthesized by hot pressing, and oxidized at 700, 850, and 1000 °C in air for up to one year. They consisted of Ti-incorporated Cr_2AlC phase, Ti-rich phase, and Cr-rich phase. The formed scales divided into a uniform oxide layer and oxide nodules. The uniform oxide layer consisted primarily of a thin Al_2O_3 scale. The oxide nodules that originated from the Ti-rich phase consisted of TiO_2, which grew by both the outward diffusion of Ti"4+ ions and inward diffusion of O"2‒ ions. Chromium did not appreciably enter the oxide scale. Instead, it existed in the Ti-incorporated Cr_7C_3 sublayer after oxidation. (Cr,Ti)_2AlC compounds had good oxidation resistance, because of formation of the Al_2O_3 barrier layer.

  16. Operating characteristics of a single-stage Stirling cryocooler capable of providing 700 W cooling power at 77 K

    Science.gov (United States)

    Xu, Ya; Sun, Daming; Qiao, Xin; Yu, Yan S. W.; Zhang, Ning; Zhang, Jie; Cai, Yachao

    2017-04-01

    High cooling capacity Stirling cryocooler generally has hundreds to thousands watts of cooling power at liquid nitrogen temperature. It is promising in boil-off gas (BOG) recondensation and high temperature superconducting (HTS) applications. A high cooling capacity Stirling cryocooler driven by a crank-rod mechanism was developed and studied systematically. The pressure and frequency characteristics of the cryocooler, the heat rejection from the ambient heat exchanger, and the cooling performance are studied under different charging pressure. Energy conversion and distribution in the cryocooler are analyzed theoretically. With an electric input power of 10.9 kW and a rotating speed of 1450 r/min of the motor, a cooling power of 700 W at 77 K and a relative Carnot efficiency of 18.2% of the cryocooler have been achieved in the present study, and the corresponding pressure ratio in the compression space reaches 2.46.

  17. Full scale calcium bromide injection with subsequent mercury oxidation and removal within wet flue gas desulphurization system: Experience at a 700 MW coal-fired power facility

    Science.gov (United States)

    Berry, Mark Simpson

    The Environmental Protection Agency promulgated the Mercury and Air Toxics Standards rule, which requires that existing power plants reduce mercury emissions to meet an emission rate of 1.2 lb/TBtu on a 30-day rolling average and that new plants meet a 0.0002 lb/GWHr emission rate. This translates to mercury removals greater than 90% for existing units and greater than 99% for new units. Current state-of-the-art technology for the control of mercury emissions uses activated carbon injected upstream of a fabric filter, a costly proposition. For example, a fabric filter, if not already available, would require a 200M capital investment for a 700 MW size unit. A lower-cost option involves the injection of activated carbon into an existing cold-side electrostatic precipitator. Both options would incur the cost of activated carbon, upwards of 3M per year. The combination of selective catalytic reduction (SCR) reactors and wet flue gas desulphurization (wet FGD) systems have demonstrated the ability to substantially reduce mercury emissions, especially at units that burn coals containing sufficient halogens. Halogens are necessary for transforming elemental mercury to oxidized mercury, which is water-soluble. Plants burning halogen-deficient coals such as Power River Basin (PRB) coals currently have no alternative but to install activated carbon-based approaches to control mercury emissions. This research consisted of investigating calcium bromide addition onto PRB coal as a method of increasing flue gas halogen concentration. The treated coal was combusted in a 700 MW boiler and the subsequent treated flue gas was introduced into a wet FGD. Short-term parametric and an 83-day longer-term tests were completed to determine the ability of calcium bromine to oxidize mercury and to study the removal of the mercury in a wet FGD. The research goal was to show that calcium bromine addition to PRB coal was a viable approach for meeting the Mercury and Air Toxics Standards rule

  18. SU-E-T-284: Revisiting Reference Dosimetry for the Model S700 Axxent 50 KV{sub p} Electronic Brachytherapy Source

    Energy Technology Data Exchange (ETDEWEB)

    Hiatt, JR [Rhode Island Hospital, Providence, RI (United States); Rivard, MJ [Tufts University School of Medicine, Boston, MA (United States)

    2014-06-01

    Purpose: The model S700 Axxent electronic brachytherapy source by Xoft was characterized in 2006 by Rivard et al. The source design was modified in 2006 to include a plastic centering insert at the source tip to more accurately position the anode. The objectives of the current study were to establish an accurate Monte Carlo source model for simulation purposes, to dosimetrically characterize the new source and obtain its TG-43 brachytherapy dosimetry parameters, and to determine dose differences between the source with and without the centering insert. Methods: Design information from dissected sources and vendor-supplied CAD drawings were used to devise the source model for radiation transport simulations of dose distributions in a water phantom. Collision kerma was estimated as a function of radial distance, r, and polar angle, θ, for determination of reference TG-43 dosimetry parameters. Simulations were run for 10{sup 10} histories, resulting in statistical uncertainties on the transverse plane of 0.03% at r=1 cm and 0.08% at r=10 cm. Results: The dose rate distribution the transverse plane did not change beyond 2% between the 2006 model and the current study. While differences exceeding 15% were observed near the source distal tip, these diminished to within 2% for r>1.5 cm. Differences exceeding a factor of two were observed near θ=150° and in contact with the source, but diminished to within 20% at r=10 cm. Conclusions: Changes in source design influenced the overall dose rate and distribution by more than 2% over a third of the available solid angle external from the source. For clinical applications using balloons or applicators with tissue located within 5 cm from the source, dose differences exceeding 2% were observed only for θ>110°. This study carefully examined the current source geometry and presents a modern reference TG-43 dosimetry dataset for the model S700 source.

  19. Technological upgrade of static system excitation of a hydraulic generator of 700 Mwats of the Hydroelectric Power Station Guri; Actualizacion tecnologica del sistema de excitacion estatico de un generador hidraulico de 700 MVA de la Central Hidroelectrica de Guri

    Energy Technology Data Exchange (ETDEWEB)

    Contreras, Romy; Guevara, Olivia [C.V.G. Electrificacion del Caroni, C.A. (EDELCA) (Venezuela)

    2004-07-01

    The Generating Units of 700 Mwatts of the Guri Plant from EDELCA are equipped with static excitation systems of analogue technology that using the closure and field's opening switch as a mechanism for the respective processes of excitation and generator dropout. This operational pattern, although functional, has been discontinuing by existing producers because of the inconvenience involved in the management of energy stored in field generator during the dropout. Alternatively, the manufacturers employ a technique of dropout without opening the switch field, based on return to the excitation transformer the energy contained in the field generator. This paper summarizes the EDELCA initiative to upgrade technologically their Generating Units, converting the excitement and dropout switch without opening the field. The project started with a phase of preliminary tests that showed the feasibility of the change and ended with the final implementation of the new scheme in a first unit (Generator n. 15). The results were successful, covering the expectations of the company, so it was decided to continue the project, extending it to the rest of the Generating Units. (author)

  20. Investigation on Long-term Creep Rupture Properties and Microstructure Stability of Fe-Ni based Alloy Ni-23Cr-7W at 700°C

    DEFF Research Database (Denmark)

    Tokairin, Tsuyoshi; Dahl, Kristian Vinter; Danielsen, Hilmar Kjartansson

    2013-01-01

    Long-term creep rupture properties and microstructural stability of Fe–Ni based alloy Ni–23Cr–7W (HR6W, ASME Code Case 2684) were experimentally investigated. Crept specimens at 700 °C for durations up to 37,667 h were chosen, the microstructure evolution during creep was characterized. Besides...... for the main strengthening precipitate, Laves phase. The alloy was proven to have good microstructural stability without observable coarsening of strengthening precipitates during long-term creep up to around 37,667 h. It was also verified that the growth kinetics of Laves phase can be well described...

  1. Oxidación en vapor de agua a 700 ºC y 750 ºC del acero inoxidable AISI 317 recubierto con aluminio por CVD-FBR.

    Directory of Open Access Journals (Sweden)

    Jose L. Marulanda

    2014-01-01

    Full Text Available Se realizó la oxidación del acero inoxidable austenítico AISI 317 recubierto con aluminio por deposición química de vapor en lecho fluidizado, a temperaturas de 700 °C y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de SEM y difracción de rayos X, para observar la morfología de los óxidos. Se realizó la simulación termodinámica del proceso de oxidación en vapor de agua de los substratos para conocer las posibles fases sólidas y gaseosas que se podrían formar, en presencia de una ambiente con 100% vapor de agua y una atmosfera de presión. La forma de ataque a 750 ºC es similar a 700 ºC, aunque la velocidad de oxidación es mayor, ya que la difusión de los elementos de aleación y las reacciones de oxidación son más rápidas. Los recubrimientos de aluminio tienen una buena resistencia a la oxidación en vapor de agua, ya que forman una capa superficial de Al 2 O 3 , que es compacta y adherente, la cual protege al substrato del ataque corrosivo.

  2. Modular hot swappable 50 V, 700 A DC power supply with active redundancy

    International Nuclear Information System (INIS)

    Badapanda, M.K.; Upadhyay, R.; Tripathi, A.; Tyagi, R.K.; Lad, M.

    2015-01-01

    A 50 V, 700 A voltage regulated modular hot swappable DC power supply has been designed and developed to bias 32 numbers of 500 W, 505.8 MHz solid state RF amplifiers for Indus-2 RF system. This power supply employs 7 numbers of 50 V, 100 A power modules which are operated in parallel and share load current equally. Active redundancy with hot swappable features incorporated in this power supply isolates the faulty module and facilitates its online replacement without affecting the operation of RF amplifiers, thereby significantly reducing the down time of the overall system. Each power module has inbuilt harmonics and power factor correction stage to improve its input performance parameters. This power supply has a dedicated controller, which monitors the healthiness of 32 numbers of RF amplifiers and 7 numbers of power modules, controls the equal sharing of load current among these modules as well as isolates the faulty RF amplifiers and power modules. The control system allows the user to set the trip limits for bias current of individual RF amplifier, power module currents and total power supply current independently for effective protection of the overall system. Issues related to EMI and high frequency switching noises are suitably taken care of in this power supply. The crucial parameters of this power supply are displayed on a local LCD panel as well as on remote PC via ethernet communication. This paper compares the availability and reliability of this hot swappable power supply with the configuration involving one dedicated power supply for each RF amplifier. The performance parameters of this power supply tested with solid state RF amplifiers are also presented in this paper. (author)

  3. Hot corrosion of Co-Cr, Co-Cr-Al, and Ni-Cr alloys in the temperature range of 700-750 deg C

    Science.gov (United States)

    Chiang, K. T.; Meier, G. H.

    1980-01-01

    The effect of SO3 pressure in the gas phase on the Na2SO4 induced hot corrosion of Co-Cr, Ni-Cr, and Co-Cr-Al alloys was studied in the temperature range 700 to 750 C. The degradation of the Co-Cr and Ni-Cr alloys was found to be associated with the formation of liquid mixed sulfates (CoSO4-Na2SO4 or NiSO4-Na2SO4) which provided a selective dissolution of the Co or Ni and a subsequent sulfidation oxidation mode of attack which prevented the maintenance of a protective Cr2O3 film. A clear mechanism was not developed for the degradation of Co-Cr-Al alloys. A pitting corrosion morphology was induced by a number of different mechanisms.

  4. SU-E-T-594: Out-Of-Field Neutron and Gamma Dose Estimated Using TLD-600/700 Pairs in the Wobbling Proton Therapy System

    International Nuclear Information System (INIS)

    Chen, Y; Lin, Y; Chen, H; Tsai, H

    2015-01-01

    Purpose: Secondary fast neutrons and gamma rays are mainly produced due to the interaction of the primary proton beam with the beam delivery nozzle. These secondary radiation dose to patients and radiation workers are unwanted. The purpose of this study is to estimate the neutron and gamma dose equivalent out of the treatment volume during the wobbling proton therapy system. Methods: Two types of thermoluminescent (TL) dosimeters, TLD-600 ( 6 LiF: Mg, Ti) and TLD-700 ( 7 LiF: Mg, Ti) were used in this study. They were calibrated in the standard neutron and gamma sources at National Standards Laboratory. Annealing procedure is 400°C for 1 hour, 100°C for 2 hours and spontaneously cooling down to the room temperature in a programmable oven. Two-peak method (a kind of glow curve analysis technique) was used to evaluate the TL response corresponding to the neutron and gamma dose. The TLD pairs were placed outside the treatment field at the neutron-gamma mixed field with 190-MeV proton beam produced by the wobbling system through the polyethylene plate phantom. The results of TLD measurement were compared to the Monte Carlo simulation. Results: The initial experiment results of calculated dose equivalents are 0.63, 0.38, 0.21 and 0.13 mSv per Gy outside the field at the distance of 50, 100, 150 and 200 cm. Conclusion: The TLD-600 and TLD-700 pairs are convenient to estimate neutron and gamma dosimetry during proton therapy. However, an accurate and suitable glow curve analysis technique is necessary. During the wobbling system proton therapy, our results showed that the neutron and gamma doses outside the treatment field are noticeable. This study was supported by the grants from the Chang Gung Memorial Hospital (CMRPD1C0682)

  5. SU-E-T-594: Out-Of-Field Neutron and Gamma Dose Estimated Using TLD-600/700 Pairs in the Wobbling Proton Therapy System

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Y [College of Medicine, Chang Gung University, Linkou, Taoyuan, Taiwan (China); Lin, Y [College of Medicine, Chang Gung University, Linkou, Taoyuan, Taiwan (China); Medical Physics Research Center, Institute for Radiological Research, Chang Gung University / Chang Gung Memorial Hospital, Linkou, Taoyuan, Taiwan (China); Chen, H [College of Medicine, Chang Gung University, Linkou, Taoyuan, Taiwan (China); Chang Gung Memorial Hospital, Linkou, Taoyuan, Taiwan (China); Tsai, H [College of Medicine, Chang Gung University, Linkou, Taoyuan, Taiwan (China); Medical Physics Research Center, Institute for Radiological Research, Chang Gung University / Chang Gung Memorial Hospital, Linkou, Taoyuan, Taiwan (China); Healthy Aging Research Center, Chang Gung University, Linkou, Taoyuan, Taiwan (China)

    2015-06-15

    Purpose: Secondary fast neutrons and gamma rays are mainly produced due to the interaction of the primary proton beam with the beam delivery nozzle. These secondary radiation dose to patients and radiation workers are unwanted. The purpose of this study is to estimate the neutron and gamma dose equivalent out of the treatment volume during the wobbling proton therapy system. Methods: Two types of thermoluminescent (TL) dosimeters, TLD-600 ({sup 6}LiF: Mg, Ti) and TLD-700 ({sup 7}LiF: Mg, Ti) were used in this study. They were calibrated in the standard neutron and gamma sources at National Standards Laboratory. Annealing procedure is 400°C for 1 hour, 100°C for 2 hours and spontaneously cooling down to the room temperature in a programmable oven. Two-peak method (a kind of glow curve analysis technique) was used to evaluate the TL response corresponding to the neutron and gamma dose. The TLD pairs were placed outside the treatment field at the neutron-gamma mixed field with 190-MeV proton beam produced by the wobbling system through the polyethylene plate phantom. The results of TLD measurement were compared to the Monte Carlo simulation. Results: The initial experiment results of calculated dose equivalents are 0.63, 0.38, 0.21 and 0.13 mSv per Gy outside the field at the distance of 50, 100, 150 and 200 cm. Conclusion: The TLD-600 and TLD-700 pairs are convenient to estimate neutron and gamma dosimetry during proton therapy. However, an accurate and suitable glow curve analysis technique is necessary. During the wobbling system proton therapy, our results showed that the neutron and gamma doses outside the treatment field are noticeable. This study was supported by the grants from the Chang Gung Memorial Hospital (CMRPD1C0682)

  6. An empirical line-by-line model for the infrared solar transmittance spectrum from 700 to 5000cm{sup -1}

    Energy Technology Data Exchange (ETDEWEB)

    Hase, F. [Institut fuer Meteorologie und Klimaforschung, Forschungszentrum Karlsruhe, Postfach 3640, D-76021 Karlsruhe (Germany)]. E-mail: frank.hase@imk.fzk.de; Demoulin, P. [Institut d' Astrophysique et de Geophysique, allee du VI aout, 17, batiment B5a, B-4000, Liege (Belgium); Sauval, A.J. [Observatoire Royal de Belgique, avenue circulaire, 3, B-1180, Bruxelles (Belgium); Toon, G.C. [Jet Propulsion Laboratory, 4800 Oak Grove Drive, Pasadena, CA 91109 (United States); Bernath, P.F. [Department of Chemistry, University of Waterloo, Waterloo, Ont., Canada N2L3G1 (Canada); Goldman, A. [Department of Physics, University of Denver, Denver, CO 80208 (United States); Hannigan, J.W. [Atmospheric Chemistry Division, National Center for Atmospheric Research, P.O. Box 3000, Boulder, CO 80303 (United States); Rinsland, C.P. [NASA Langley Research Center, Hampton, VA 23681-2199 (United States)

    2006-12-15

    An empirical line-by-line model for the infrared solar transmittance spectrum is presented. The model can be incorporated into radiative transfer codes to allow fast calculation of all relevant emission and absorption features in the solar spectrum in the mid-infrared region from 700 to 5000cm{sup -1}. The transmittance is modelled as a function of the diameter of the field-of-view centered on the solar disk: the line broadening due to solar rotation as well as center-to-limb variations in strength and width are taken into account for stronger lines. Applications of the model presented here are in the fields of terrestrial remote sensing in the mid-infrared spectral region when the sun is used as radiation source or scattered solar radiation contributes to the measured signal and in the fields of atmospheric radiative transfer algorithms which compute the propagation of infrared solar radiation in the terrestrial atmosphere.

  7. The Jovian ring was imaged at 2.26+/-0.03 microns at approximately 7:00 UT on 12 July, 1994, from NA

    Science.gov (United States)

    2002-01-01

    The Jovian ring was imaged at 2.26+/-0.03 microns at approximately 7:00 UT on 12 July, 1994, from NASA's Infrared Telescope Facility. The image was coadded from three 30-second exposures with sky subtracted. The resolution was 0.31 arcseconds per pixel. A S/N 5 per pixel was obtained for the coadded images. Photometry on the ring image is pending. This is part of a program to monitor the effects of the dust from Comet Shoemaker-Levy 9 on the Jovian ring system. More images will be taken during and after the impacts of the fragments. The image was obtained by Philip Esterle (University of Maryland), Casey Lisse (NASA/Goddard Space Flight Center), and Mark Shure (University of Hawaii).

  8. Fireside corrosion of nickel base alloys in future 700 C coal fired power plants; Rauchgasseitige Korrosion von Nickelbasislegierungen fuer zukuenftige 700 C-Dampfkraftwerke

    Energy Technology Data Exchange (ETDEWEB)

    Luettschwager, Frank

    2011-09-27

    Coal is still the most important energy source in Germany. In 2009 it produced 42.9 % of the overall German electrical power. Coal is available world-wide in large quantities and can be delivered economically. One of the possible ways to reduce CO{sub 2} pollution is the increase of efficiency of coal fired power plants, which requires steam conditions of up to 700 C - 730 C and 350 bar. Because many German power units will reach the end of their technical lifespan in a few years or the following decade, one will have the possibility to build up modern types of power plants with increased efficiency of more than 50 %. Some international standards (European Pressure Equipment Directive or ASME Boiler and Pressure Vessel Code) require 100 000 hour creep rupture strength of 100 MPa at 750 C. Therefore, nickel base alloys are in the focus of material qualification processes. Nickel base alloys are well investigated due to their hot corrosion behaviour. It is known that sodium sulphate may generate hot corrosion on those alloys at temperatures above its melting point of 884 C. On nickel base alloys an eutectic mixture of nickel sulphate and sodium sulphate with a melting point of 671 C can be generated, which leads to accelerated corrosion. This work examines, whether the high amount of sulphur and alkali metals will induce hot corrosion at the estimated working temperature on devices manufactured from nickel base alloy. Two synthetic coal ash deposits, according to the chemical composition of hard coal and lignite, and typical flue gases with and without sulphur dioxide were blended of pure agents. The reactions of the deposits with heater tubes' materials and synthetic flue gases are examined in the temperature range from 650 C to 800 C and different time ranges up to 2000 hours. The corroded specimen are examined with SEM/EDX to identify relevant corrosion products and determine the corrosivity of deposited compounds. Deposits increase the corrosion rate of

  9. Life Prediction on a T700 Carbon Fiber Reinforced Cylinder with Limited Accelerated Life Testing Data

    Directory of Open Access Journals (Sweden)

    Ma Xiaobing

    2015-01-01

    Full Text Available An accelerated life testing investigation was conducted on a composite cylinder that consists of aluminum alloy and T700 carbon fiber. The ultimate failure stress predictions of cylinders were obtained by the mixing rule and verified by the blasting static pressure method. Based on the stress prediction of cylinder under working conditions, the constant stress accelerated life test of the cylinder was designed. However, the failure data cannot be sufficiently obtained by the accelerated life test due to the time limitation. Therefore, most of the data presented to be high censored in high stress level and zero-failure data in low stress level. When using the traditional method for rupture life prediction, the results showed to be of lower confidence. In this study, the consistency of failure mechanism for carbon fiber and cylinder was analyzed firstly. According to the analysis result, the statistical test information of carbon fiber could be utilized for the accelerated model constitution. Then, rupture life prediction method for cylinder was proposed based on the accelerated life test data and carbon fiber test data. In this way, the life prediction accuracy of cylinder could be improved obviously, and the results showed that the accuracy of this method increased by 35%.

  10. Site Characterization Report ORGDP Diffusion Facilities Permanent Shutdown K-700 Power House and K-27 Switch Yard/Switch House

    Energy Technology Data Exchange (ETDEWEB)

    Thomas R.J., Blanchard R.D.

    1988-06-13

    The K-700 Power House area, initially built to supply power to the K-25 gaseous diffusion plant was shutdown and disassembled in the 1960s. This shutdown was initiated by TVA supplying economical power to the diffusion plant complex. As a result of world wide over production of enriched, reactor grade U{sup 235}, the K-27 switch yard and switch house area was placed in standby in 1985. Subsequently, as the future production requirements decreased, the cost of production increased and the separation technologies for other processes improved, the facility was permanently shutdown in December, 1987. This Site Characterization Report is a part of the FY-88 engineering Feasibility Study for placing ORGDP Gaseous Diffusion Process facilities in 'Permanent Shutdown'. It is sponsored by the Department of Energy through Virgil Lowery of Headquarters--Enrichment and through Don Cox of ORO--Enrichment Operations. The primary purpose of these building or site characterization reports is to document, quantify, and map the following potential problems: Asbestos; PCB containing fluids; Oils, coolants, and chemicals; and External contamination. With the documented quantification of the concerns (problems) the Engineering Feasibility Study will then proceed with examining the potential solutions. For this study, permanent shutdown is defined as the securing and/or conditioning of each facility to provide 20 years of safe service with minimal expenditures and, where feasible, also serving DOE's needs for long-term warehousing or other such low-risk use. The K-700 power house series of buildings were either masonry construction or a mix of masonry and wood. The power generating equipment was removed and sold as salvage in the mid 1960s but the buildings and auxiliary equipment were left intact. The nine ancillary buildings in the power house area use early in the Manhattan Project for special research projects, were left intact minus the original special equipment

  11. Effect of flow configuration on moderator temperature distribution for 700 MWe Calandria

    International Nuclear Information System (INIS)

    Bharj, Jaspal Singh; Sahaya, R.R.; Dharne, S.P.

    2009-01-01

    The Calandria of a Pressurized Heavy Water Reactor (PHWR) is essentially a horizontal cylindrical vessel housing a matrix of horizontal tubes called Calandria tubes within which is contained the pressure tubes that house the fuel bundles. In addition there are horizontal and vertical flux control and shutdown devices. The Calandria is filled with heavy water moderator at a pressure slightly above the atmosphere. A large amount of heat (about 125 MWth) is generated within the moderator mainly due to neutron slowing down and attenuation of gamma radiations. This heat generation gives rise to a strong buoyancy-driven natural convection flow. In the proposed configuration of 700 MWe PHWR Calandria, moderator inlet diffusers are directed upwards and the outlet nozzles are at the bottom of the Calandria. The basis for the above said inlet/outlet configuration depends upon the various factors like space availability, NPSH requirement for the moderator pumps, and interference of flow with the other components inside the Calandria. This configuration is not conducive for the buoyancy-dominated flows generated due to large volumetric heat generation in the moderator. In order to see the effects of changes in flow configuration by re-orienting the inlet/outlet, a CFD study was undertaken for moderator flows in the conceptual Calandria. In the study, the moderator inlet diffusers direct the cool moderator towards the bottom of the Calandria and hot moderator flows out through the outlets in the upper half of the Calandria. The results of the study with various flow configurations show that modification in moderator flow configuration in Calandria, by way of introduction of moderator in the downward direction through diffusers and provision of the exits from the upper portion of the Calandria, results in significant reduction of the maximum temperature of moderator in Calandria. Further, the temperature distribution in the Calandria in the proposed configurations is much more

  12. The influence of combined addition of phosphorus and titanium on void swelling of austenitic Fe-Cr-Ni alloys at 646-700 K

    International Nuclear Information System (INIS)

    Watanabe, H.; Muroga, T.; Yoshida, N.

    1994-01-01

    The influence of combined addition of phosphorus and titanium on void swelling of model Fe-Cr-Ni austenitic alloys at 646 to 700 K under fast neutron irradiation has been investigated, in comparison with that of a complex austenitic alloy (JPCA-2). In the model alloys, void swelling decreased with increasing phosphorus content. Void average size and density of JPCA-2 were comparable to those of the 0.024P alloy. The fact that these two alloys have the same phosphorus level suggests the void swelling of the model alloys would be strongly suppressed by increasing the phosphorus concentration and/or coaddition of phosphorus and titanium. The present study demonstrated that the phosphorus level is the strongest determinant of void swelling of both model and complex austenitic alloys. ((orig.))

  13. Corrosion behavior of Fe-Si metallic coatings added with NiCrAlY in an environment of fuel oil ashes at 700 C

    Energy Technology Data Exchange (ETDEWEB)

    Salinas-Bravo, V.M.; Porcayo-Calderon, J.; Romero-Castanon, T. [Instituto de Investigaciones Electricas, Gerencia de Procesos Termicos., Av. Reforma 113, C.P. 62490 Col. Palmira. Temixco. Morelos (Mexico); Dominguez-Patino, G.; Gonzalez-Rodriguez, J.G. [U.A.E.M. Centro de Investigaciones en Ingenieria y Ciencias Aplicadas., Av. Universidad 1001, C.P. 62210, Col. Chamilpa. Cuernavaca, Morelos (Mexico)

    2005-07-01

    Electrochemical potentiodynamic polarization curves and immersion tests for 300 h at 700 C in a furnace have been used to evaluate the corrosion resistance of Fe-Si metallic coatings added with up to 50 wt.% of NiCrAIY. The corrosive environment was fuel oil ashes from a steam generator. The composition of fuel oil ashes includes high content of vanadium, sodium and sulfur. The results obtained show that only the addition of 20 wt.% NiCrAlY to the Fe-Si coating improves its corrosion resistance. The behavior of all tested coatings is explained by the results obtained from the analysis of every coating using electron microscopy and energy dispersive X-ray analysis. (Abstract Copyright [2005], Wiley Periodicals, Inc.)

  14. A study of the reaction Li+HCl by the technique of time-resolved laser-induced fluorescence spectroscopy of Li (2 2PJ-2 2S1/2, λ=670.7 nm) between 700 and 1000 K

    Science.gov (United States)

    Plane, John M. C.; Saltzman, Eric S.

    1987-10-01

    A kinetic study is presented of the reaction between lithium atoms and hydrogen chloride over the temperature range 700-1000 K. Li atoms are produced in an excess of HCl and He bath gas by pulsed photolysis of LiCl vapor. The concentration of the metal atoms is then monitored in real time by the technique of laser-induced fluorescence of Li atoms at λ=670.7 nm using a pulsed nitrogen-pumped dye laser and box-car integration of the fluorescence signal. Absolute second-order rate constants for this reaction have been measured at T=700, 750, 800, and 900 K. At T=1000 K the reverse reaction is sufficiently fast that equilibrium is rapidly established on the time scale of the experiment. A fit of the data between 700 and 900 K to the Arrhenius form, with 2σ errors calculated from the absolute errors in the rate constants, yields k(T)=(3.8±1.1)×10-10 exp[-(883±218)/T] cm3 molecule-1 s-1. This result is interpreted through a modified form of collision theory which is constrained to take account of the conservation of total angular momentum during the reaction. Thereby we obtain an estimate for the reaction energy threshold, E0=8.2±1.4 kJ mol-1 (where the error arises from uncertainty in the exothermicity of the reaction), in very good agreement with a crossed molecular beam study of the title reaction, and substantially lower than estimates of E0 from both semiempirical and ab initio calculations of the potential energy surface.

  15. Measurement of Spin Dependent Observables in the $\\overline pN$ Elastic Scattering from 300 to 700 MeV/c

    CERN Multimedia

    2002-01-01

    The aim of the experiment is to measure @*N spin obssservables using a frozen spin target and a high resolution spectrometer (SPES II). The &bar.NN scattering is usually described with NN potentials transformed by G-parity, where the large annihilation cross section (@s^a^n/@s^e^l$>$2) is taken into account. The different theoretical approaches fit reasonably well the existing data on spin integrated cross sections. For the spin dependent observables, the predictions depend consistently on the theoretical inputs.\\\\ \\\\ A strong energy dependence of the @*p polarization Ay(@q) is predicted. We plan to check it measuring the angular distribution of Ay(@q) for @* momenta between 300 and 700 MV/c. Using a deuterium target, measurements of Ay(@q) for @*d in the same energy range will provide information on @*n scattering.\\\\ \\\\ The @* beam hits a 5 mm thick frozen spin target which has a large opening aperture. We expect a polarization of @=~80\\% with a low holding field of (.35Tm). The incident trajectory is de...

  16. Testing on a Large Scale Running the ATLAS Data Acquisition and High Level Trigger Software on 700 PC Nodes

    CERN Document Server

    Burckhart-Chromek, Doris; Adragna, P; Alexandrov, L; Amorim, A; Armstrong, S; Badescu, E; Baines, J T M; Barros, N; Beck, H P; Bee, C; Blair, R; Bogaerts, J A C; Bold, T; Bosman, M; Caprini, M; Caramarcu, C; Ciobotaru, M; Comune, G; Corso-Radu, A; Cranfield, R; Crone, G; Dawson, J; Della Pietra, M; Di Mattia, A; Dobinson, Robert W; Dobson, M; Dos Anjos, A; Dotti, A; Drake, G; Ellis, Nick; Ermoline, Y; Ertorer, E; Falciano, S; Ferrari, R; Ferrer, M L; Francis, D; Gadomski, S; Gameiro, S; Garitaonandia, H; Gaudio, G; George, S; Gesualdi-Mello, A; Gorini, B; Green, B; Haas, S; Haberichter, W N; Hadavand, H; Haeberli, C; Haller, J; Hansen, J; Hauser, R; Hillier, S J; Höcker, A; Hughes-Jones, R E; Joos, M; Kazarov, A; Kieft, G; Klous, S; Kohno, T; Kolos, S; Korcyl, K; Kordas, K; Kotov, V; Kugel, A; Landon, M; Lankford, A; Leahu, L; Leahu, M; Lehmann-Miotto, G; Le Vine, M J; Liu, W; Maeno, T; Männer, R; Mapelli, L; Martin, B; Masik, J; McLaren, R; Meessen, C; Meirosu, C; Mineev, M; Misiejuk, A; Morettini, P; Mornacchi, G; Müller, M; Garcia-Murillo, R; Nagasaka, Y; Negri, A; Padilla, C; Pasqualucci, E; Pauly, T; Perera, V; Petersen, J; Pope, B; Albuquerque-Portes, M; Pretzl, K; Prigent, D; Roda, C; Ryabov, Yu; Salvatore, D; Schiavi, C; Schlereth, J L; Scholtes, I; Sole-Segura, E; Seixas, M; Sloper, J; Soloviev, I; Spiwoks, R; Stamen, R; Stancu, S; Strong, S; Sushkov, S; Szymocha, T; Tapprogge, S; Teixeira-Dias, P; Torres, R; Touchard, F; Tremblet, L; Ünel, G; Van Wasen, J; Vandelli, W; Vaz-Gil-Lopes, L; Vermeulen, J C; von der Schmitt, H; Wengler, T; Werner, P; Wheeler, S; Wickens, F; Wiedenmann, W; Wiesmann, M; Wu, X; Yasu, Y; Yu, M; Zema, F; Zobernig, H; Computing In High Energy and Nuclear Physics

    2006-01-01

    The ATLAS Data Acquisition (DAQ) and High Level Trigger (HLT) software system will be comprised initially of 2000 PC nodes which take part in the control, event readout, second level trigger and event filter operations. This high number of PCs will only be purchased before data taking in 2007. The large CERN IT LXBATCH facility provided the opportunity to run in July 2005 online functionality tests over a period of 5 weeks on a stepwise increasing farm size from 100 up to 700 PC dual nodes. The interplay between the control and monitoring software with the event readout, event building and the trigger software has been exercised the first time as an integrated system on this large scale. New was also to run algorithms in the online environment for the trigger selection and in the event filter processing tasks on a larger scale. A mechanism has been developed to package the offline software together with the DAQ/HLT software and to distribute it via peer-to-peer software efficiently to this large pc cluster. T...

  17. Testing on a Large Scale running the ATLAS Data Acquisition and High Level Trigger Software on 700 PC Nodes

    CERN Document Server

    Burckhart-Chromek, Doris; Adragna, P; Albuquerque-Portes, M; Alexandrov, L; Amorim, A; Armstrong, S; Badescu, E; Baines, J T M; Barros, N; Beck, H P; Bee, C; Blair, R; Bogaerts, J A C; Bold, T; Bosman, M; Caprini, M; Caramarcu, C; Ciobotaru, M; Comune, G; Corso-Radu, A; Cranfield, R; Crone, G; Dawson, J; Della Pietra, M; Di Mattia, A; Dobinson, Robert W; Dobson, M; Dos Anjos, A; Dotti, A; Drake, G; Ellis, Nick; Ermoline, Y; Ertorer, E; Falciano, S; Ferrari, R; Ferrer, M L; Francis, D; Gadomski, S; Gameiro, S; Garcia-Murillo, R; Garitaonandia, H; Gaudio, G; George, S; Gesualdi-Mello, A; Gorini, B; Green, B; Haas, S; Haberichter, W N; Hadavand, H; Haeberli, C; Haller, J; Hansen, J; Hauser, R; Hillier, S J; Hughes-Jones, R E; Höcker, A; Joos, M; Kazarov, A; Kieft, G; Klous, S; Kohno, T; Kolos, S; Korcyl, K; Kordas, K; Kotov, V; Kugel, A; Landon, M; Lankford, A; Le Vine, M J; Leahu, L; Leahu, M; Lehmann-Miotto, G; Liu, W; Maeno, T; Mapelli, L; Martin, B; Masik, J; McLaren, R; Meessen, C; Meirosu, C; Mineev, M; Misiejuk, A; Morettini, P; Mornacchi, G; Männer, R; Müller, M; Nagasaka, Y; Negri, A; Padilla, C; Pasqualucci, E; Pauly, T; Perera, V; Petersen, J; Pope, B; Pretzl, K; Prigent, D; Roda, C; Ryabov, Yu; Salvatore, D; Schiavi, C; Schlereth, J L; Scholtes, I; Seixas, M; Sloper, J; Sole-Segura, E; Soloviev, I; Spiwoks, R; Stamen, R; Stancu, S; Strong, S; Sushkov, S; Szymocha, T; Tapprogge, S; Teixeira-Dias, P; Torres, R; Touchard, F; Tremblet, L; Van Wasen, J; Vandelli, W; Vaz-Gil-Lopes, L; Vermeulen, J C; Wengler, T; Werner, P; Wheeler, S; Wickens, F; Wiedenmann, W; Wiesmann, M; Wu, X; Yasu, Y; Yu, M; Zema, F; Zobernig, H; von der Schmitt, H; Ünel, G; Computing In High Energy and Nuclear Physics

    2006-01-01

    The ATLAS Data Acquisition (DAQ) and High Level Trigger (HLT) software system will be comprised initially of 2000 PC nodes which take part in the control, event readout, second level trigger and event filter operations. This high number of PCs will only be purchased before data taking in 2007. The large CERN IT LXBATCH facility provided the opportunity to run in July 2005 online functionality tests over a period of 5 weeks on a stepwise increasing farm size from 100 up to 700 PC dual nodes. The interplay between the control and monitoring software with the event readout, event building and the trigger software has been exercised the first time as an integrated system on this large scale. New was also to run algorithms in the online environment for the trigger selection and in the event filter processing tasks on a larger scale. A mechanism has been developed to package the offline software together with the DAQ/HLT software and to distribute it via peer-to-peer software efficiently to this large pc cluster. T...

  18. Conducted and radiated emission tests for fault tolerant power distribution system ECPS-100 developed for PHWR700MW C and I

    International Nuclear Information System (INIS)

    Das, Shantanu; Yadav, Ramnayan

    2016-01-01

    Electronics devices when designed to meet specific requirements, the designers do not generally envisage the amount of electromagnetic interference that this particular device may give as power line conducted noise and radiated noise. After the product is developed, the quantification of the same is carried out in certified EMI-EMC set-up to get these figures of conducted emissions (CE) and radiated emissions (RE), and its mitigation as per limits of the chosen standard. In the latest TM embodiment of Fault Tolerant Power Distribution System ECPS"T"M (Electronics Corporation Power Supply) developed for NPCIL (PHWR700MW plant) we carried out CE and RE tests and quantified the spectrum obtained for CE and RE, and mitigated them as per CISPR22 standards. In this short article we bring out the CE and RE results of the latest product ECPS, done at EMI-EMC Centre of ECIL Hyderabad. (author)

  19. Total L-shell X-ray production cross sections by 400-700 keV proton impact for elements with 34≤Z≤53

    International Nuclear Information System (INIS)

    Miranda, J.; Ledesma, R.; Lucio, O.G. de

    2001-01-01

    Total L-shell X-ray production cross sections induced by protons with energies between 400 and 700 keV were measured for elements with atomic number Z between 34 and 53. The ECPSSR theory describes appropriately the results. This model modifies the plane wave born approximation by considering projectile energy loss (E), Coulomb deflection of the incoming ion (C), polarization and change in electron binding energies through a perturbed stationary states method (PSS) and relativistic values of target electron mass (R). A comparison is given with previously published data for proton energies below 1 MeV and 26 ≤ Z ≤ 53, based on a scaling obtained from a reduced velocity parameter ξ L R . The results show that the scaling for these atomic numbers and energy ranges is adequate and a semi-empirical expression to calculate those cross sections is proposed

  20. Modificaciones en la composición corporal después de realizar una prueba de ultrarresistencia de 1.700 km en bicicleta de montaña

    Directory of Open Access Journals (Sweden)

    Vicente Clemente Suárez

    2010-01-01

    Full Text Available El estudio de los cambios en la composición corporal en pruebas de resistencia se ha limitado en la mayoría de los casos al estudio de las pérdidas de peso corporal. El presente estudio pretende analizar los cambios producidos en la composición corporal (agua, proteínas, minerales, grasa, y músculo producidos después de realizar una prueba de 1.700 Km en bicicleta de montaña cruzando África de este a oeste. Se analizaron 5 sujetos (73,3±10,2 kg, 170±0,1 cm, 51,2±6,9 años antes y después de realizar una prueba de ultrarresistencia en bicicleta de montaña de 1.700 km durante 17 días (100-110 km por etapa. Se analizaron los siguientes parámetros: Masa Agua Intracelular, Masa Agua Extracelular, Proteínas, Masa Mineral, Masa Grasa Corporal, Agua Corporal Total, Masa Músculo Esquelético, Masa Libre de Grasa, Peso y Área Grasa Visceral mediante bioimpedancia eléctrica (BIA con el analizador INBODY 720. Los resultados muestran una disminución no significativa de los parámetros de peso corporal y masa grasa, una disminución significativa en el área de grasa visceral (p>0,05. El resto de parámetros se mantuvieron en valores cercanos a la toma inicial. En conclusión este tipo de pruebas de ultrarresistencia únicamente afecta a los parámetros de grasa visceral, manteniendo el resto de variables de composición corporal sin cambios significativos.

  1. Oxidación en vapor de agua a 700 ºC y 750 ºC del acero inoxidable AISI 317 recubierto con aluminio por CVD-FBR.

    OpenAIRE

    Jose L. Marulanda; Saul I. Castañeda; Aduljay Remolina

    2014-01-01

    Se realizó la oxidación del acero inoxidable austenítico AISI 317 recubierto con aluminio por deposición química de vapor en lecho fluidizado, a temperaturas de 700 °C y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de SEM y difracción de rayos X, para observar la morfología de los óxidos. Se realizó la simulación termodinámica del proceso de oxidación en vapor de agua de...

  2. Modificaciones en la composición corporal después de realizar una prueba de ultrarresistencia de 1.700 km en bicicleta de montaña

    OpenAIRE

    Clemente Suárez, Vicente J.; González-Ravé, José María

    2010-01-01

    El estudio de los cambios en la composición corporal en pruebas de resistencia se ha limitado en la mayoría de los casos al estudio de las pérdidas de peso corporal. El presente estudio pretende analizar los cambios producidos en la composición corporal (agua, proteínas, minerales, grasa, y músculo) producidos después de realizar una prueba de 1.700 Km en bicicleta de montaña cruzando África de este a oeste. Se analizaron 5 sujetos (73,3±10,2 kg, 170±0,1 cm, 51,2±6,9 a...

  3. A galaxy rapidly forming stars 700 million years after the Big Bang at redshift 7.51.

    Science.gov (United States)

    Finkelstein, S L; Papovich, C; Dickinson, M; Song, M; Tilvi, V; Koekemoer, A M; Finkelstein, K D; Mobasher, B; Ferguson, H C; Giavalisco, M; Reddy, N; Ashby, M L N; Dekel, A; Fazio, G G; Fontana, A; Grogin, N A; Huang, J-S; Kocevski, D; Rafelski, M; Weiner, B J; Willner, S P

    2013-10-24

    Of several dozen galaxies observed spectroscopically that are candidates for having a redshift (z) in excess of seven, only five have had their redshifts confirmed via Lyman α emission, at z = 7.008, 7.045, 7.109, 7.213 and 7.215 (refs 1-4). The small fraction of confirmed galaxies may indicate that the neutral fraction in the intergalactic medium rises quickly at z > 6.5, given that Lyman α is resonantly scattered by neutral gas. The small samples and limited depth of previous observations, however, makes these conclusions tentative. Here we report a deep near-infrared spectroscopic survey of 43 photometrically-selected galaxies with z > 6.5. We detect a near-infrared emission line from only a single galaxy, confirming that some process is making Lyman α difficult to detect. The detected emission line at a wavelength of 1.0343 micrometres is likely to be Lyman α emission, placing this galaxy at a redshift z = 7.51, an epoch 700 million years after the Big Bang. This galaxy's colours are consistent with significant metal content, implying that galaxies become enriched rapidly. We calculate a surprisingly high star-formation rate of about 330 solar masses per year, which is more than a factor of 100 greater than that seen in the Milky Way. Such a galaxy is unexpected in a survey of our size, suggesting that the early Universe may harbour a larger number of intense sites of star formation than expected.

  4. Reactive wetting of Ti-6Al-4V alloy by molten Al 4043 and 6061 alloys at 600-700 C

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Qiaoli; Li, Fuxiang; Jin, Peng; Yu, Weiyuan [Lanzhou Univ. of Technology (China). State Key Lab. of Advanced Processing and Recycling of Non-ferrous Metal

    2017-06-15

    Wetting of Ti-6Al-4V alloy by two industrial grade Al alloys (i.e., Al 6061 and 4043 alloys) was studied using the sessile drop method at 600-700 C under high vacuum. Al/Ti-6Al-4V is a typical reactive wetting system with good final wettability accompanied by the formation of precursor film which is actually an extended reaction layer. The formation mechanism for the precursor film is ''subcutaneous infiltration''. The small amount of alloying element Si in the alloys can cause significant segregation at the liquid/solid interface which satisfies the thermodynamic condition. The wetting behavior can be described by the classic reaction product control models, and Ti{sub 7}Al{sub 5}Si{sub 12} decomposition and Al{sub 3}Ti formation correspond to the two spreading stages. The small difference in alloying elements in Al 6061 and 4043 resulted in distinctly different interface structures, formation of precursor film and spreading dynamics, especially for the Si segregation at the interface.

  5. The effect of microstructure on the sheared edge quality and hole expansion ratio of hot-rolled 700 MPa steel

    Science.gov (United States)

    Kaijalainen, A.; Kesti, V.; Vierelä, R.; Ylitolva, M.; Porter, D.; Kömi, J.

    2017-09-01

    The effects of microstructure on the cutting and hole expansion properties of three thermomechanically rolled steels have been investigated. The yield strength of the studied 3 mm thick strip steels was approximately 700 MPa. Detailed microstructural studies using laser scanning confocal microscopy (LCSM), FESEM and FESEM-EBSD revealed that the three investigated materials consist of 1) single-phase polygonal ferrite, 2) polygonal ferrite with precipitates and 3) granular bainite. The quality of mechanically sheared edges were evaluated using visual inspection and LSCM, while hole expansion properties were characterised according to the methods described in ISO 16630. Roughness values (Ra and Rz) of the sheet edge with different cutting clearances varied between 12 µm to 21 µm and 133 µm to 225 µm, respectively. Mean hole expansion ratios varied from 28.4% to 40.5%. It was shown that granular bainite produced the finest cutting edge, but the hole expansion ratio remained at the same level as in the steel comprising single-phase ferrite. This indicates that a single-phase ferritic matrix enhances hole expansion properties even with low quality edges. A brief discussion of the microstructural features controlling the cutting quality and hole expansion properties is given.

  6. Modificaciones en la composición corporal después de realizar una prueba de ultrarresistencia de 1.700 km en bicicleta de montaña

    OpenAIRE

    Vicente Clemente Suárez; José María González-Ravé

    2010-01-01

    El estudio de los cambios en la composición corporal en pruebas de resistencia se ha limitado en la mayoría de los casos al estudio de las pérdidas de peso corporal. El presente estudio pretende analizar los cambios producidos en la composición corporal (agua, proteínas, minerales, grasa, y músculo) producidos después de realizar una prueba de 1.700 Km en bicicleta de montaña cruzando África de este a oeste. Se analizaron 5 sujetos (73,3±10,2 kg, 170±0,1 cm, 51,2±6,9 años) antes y después de ...

  7. Size Effect Studies of the Creep Behaviour of 20MnMoNi55 at Temperatures from 700 oC to 900 oC

    International Nuclear Information System (INIS)

    Krompholz, K.; Groth, E.; Kalkhof, D.

    2000-11-01

    One of the objectives of the REVISA project (REactor Vessel Integrity in Severe Accidents) is to assess size and scale effects in plastic flow and failure. This includes an experimental programme devoted to characterising the influence of specimen size, strain rate, and strain gradients at various temperatures. One of the materials selected was the forged reactor pressure vessel material 20 MnMoNi 55, material number 1.6310 (heat number 69906). Among others, a size effect study of the creep response of this material was performed, using geometrically similar smooth specimens with 5 mm and 20 mm diameter. The tests were done under constant load in an inert atmosphere at 700 o C, 800 o C, and 900 o C, close to and within the phase transformation regime. The mechanical stresses varied from 10 MPa to 30 MPa, depending on temperature. Prior to creep testing the temperature and time dependence of scale oxidation as well as the temperature regime of the phase transformation was determined. The creep tests were supplemented by metallographical investigations.The test results are presented in form of creep curves strain versus time from which characteristic creep data were determined as a function of the stress level at given temperatures. The characteristic data are the times to 5% and 15% strain and to rupture, the secondary (minimum) creep rate, the elongation at fracture within the gauge length, the type of fracture and the area reduction after fracture. From metallographical investigations the austenitic phase contents at different temperatures could be estimated. From these data also the parameters of the regression calculation (e.g. Norton's creep law) were obtained. The evaluation revealed that the creep curves and characteristic data are size dependent of varying degree, depending on the stress and temperature level, but the size influence cannot be related to corrosion or orientation effects or to macroscopic heterogeneity (position effect) of the original

  8. Pyridostigmine bromide and the long-term subjective health status of a sample of over 700 male Reserve Component Gulf War era veterans.

    Science.gov (United States)

    Schumm, Walter R; Reppert, Earl J; Jurich, Anthony P; Bollman, Stephan R; Webb, Farrell J; Castelo, Carlos S; Stever, James C; Kaufman, Mark; Deng, Liang-Yu; Krehbiel, Michelle; Owens, Barbara L; Hall, Carolyn A; Brown, Beverlyn F Cay; Lash, Jeanne F; Fink, Carol J; Crow, Janet R; Bonjour, Gabriele N

    2002-06-01

    Data from a 1996-1997 survey of approximately 700 Reserve Component male veterans indicate that the consumption of pyridostigmine bromide pills, used as a pretreatment for potential exposure to the nerve agent Soman, was a significant predictor of declines in reported subjective health status after the war, even after controlling for a number of other possible factors. Reported reactions to vaccines and other medications also predicted declines in subjective health. While higher military rank generally predicted better health during and after the war, educational attainment, minority status, number of days in theater, and age generally did not predict changes in subjective health. Although servicemembers were directed to take three pills a day, veterans reported a range of compliance--less than a fourth (24%) followed the medical instructions compared to 61% who took fewer than three pills daily and 6% who took six or more pills a day. Implications for use of pyridostigmine bromide are discussed.

  9. 700 F hybrid capacitors cells composed of activated carbon and Li4Ti5O12 microspheres with ultra-long cycle life

    Science.gov (United States)

    Ruan, Dianbo; Kim, Myeong-Seong; Yang, Bin; Qin, Jun; Kim, Kwang-Bum; Lee, Sang-Hyun; Liu, Qiuxiang; Tan, Lei; Qiao, Zhijun

    2017-10-01

    To address the large-scale application demands of high energy density, high power density, and long cycle lifetime, 700-F hybrid capacitor pouch cells have been prepared, comprising ∼240-μm-thick activated carbon cathodes, and ∼60-μm-thick Li4Ti5O12 anodes. Microspherical Li4Ti5O12 (M-LTO) synthesized by spray-drying features 200-400 nm primary particles and interconnected nanopore structures. M-LTO half-cells exhibits high specific capacities (175 mAhh g-1), good rate capabilities (148 mAhh g-1 at 20 C), and ultra-long cycling stabilities (90% specific capacity retention after 10,000 cycles). In addition, the obtained hybrid capacitors comprising activated carbon (AC) and M-LTO shows excellent cell performances, achieving a maximum energy density of 51.65 Wh kg-1, a maximum power density of 2466 W kg-1, and ∼92% capacitance retention after 10,000 cycles, thus meeting the demands for large-scale applications such as trolleybuses.

  10. Statistical Study of Aircraft Icing Probabilities at the 700- and 500- Millibar Levels over Ocean Areas in the Northern Hemisphere

    Science.gov (United States)

    Perkins, Porter J.; Lewis, William; Mulholland, Donald R.

    1957-01-01

    A statistical study is made of icing data reported from weather reconnaissance aircraft flown by Air Weather Service (USAF). The weather missions studied were flown at fixed flight levels of 500 millibars (18,000 ft) and 700 millibars (10,000 ft) over wide areas of the Pacific, Atlantic, and Arctic Oceans. This report is presented as part of a program conducted by the NACA to obtain extensive icing statistics relevant to aircraft design and operation. The thousands of in-flight observations recorded over a 2- to 4-year period provide reliable statistics on icing encounters for the specific areas, altitudes, and seasons included in the data. The relative frequencies of icing occurrence are presented, together with the estimated icing probabilities and the relation of these probabilities to the frequencies of flight in clouds and cloud temperatures. The results show that aircraft operators can expect icing probabilities to vary widely throughout the year from near zero in the cold Arctic areas in winter up to 7 percent in areas where greater cloudiness and warmer temperatures prevail. The data also reveal a general tendency of colder cloud temperatures to reduce the probability of icing in equally cloudy conditions.

  11. An accurate calibration method for high pressure vibrating tube densimeters in the density interval (700 to 1600) kg . m-3

    International Nuclear Information System (INIS)

    Sanmamed, Yolanda A.; Dopazo-Paz, Ana; Gonzalez-Salgado, Diego; Troncoso, Jacobo; Romani, Luis

    2009-01-01

    A calibration procedure of vibrating tube densimeters for density measurement of liquids in the intervals (700 to 1600) kg . m -3 , (283.15 to 323.15) K, and (0.1 to 60) MPa is presented. It is based on the modelization of the vibrating tube as a thick-tube clamped at one end (cantilever) whose stress and thermal behaviour follows the ideas proposed in the Forced Path Mechanical Calibration model (FPMC). Model parameters are determined using two calibration fluids with densities certified at atmospheric pressure (dodecane and tetracholoroethylene) and a third one with densities known as a function of pressure (water). It is applied to the Anton Paar 512P densimeter, obtaining density measurements with an expanded uncertainty less than 0.2 kg . m -3 in the working intervals. This accuracy comes from the combination of several factors: densimeter behaves linearly in the working density interval, densities of both calibration fluids cover that interval and they have a very low uncertainty, and the mechanical behaviour of the tube is well characterized by the considered model. The main application of this method is the precise measurement of high density fluids for which most of the calibration procedures are inaccurate.

  12. Study of the {phi} meson in the pp{yields}K{sub 1}{sup 0}K{sub 2}{sup 0}{pi}{sup +}{pi}{sup -} K{sub 1}{sup 0}K{sub 2}{sup 0} annihilations at 700-750 MeV/c; Estudio del Meson {phi} en las aniquilaciones pp {yields}{phi}K{sub 1}{sup 0}K{sub 2}{sup 0}{pi}{sup +}{pi}{sup -} K{sub 1}{sup 0}K{sub 2}{sup 0} a 700-750 MeV/c de momento del haz

    Energy Technology Data Exchange (ETDEWEB)

    Gil Lopez, E

    1976-07-01

    We have measured the mass and width of the {phi} meson using the pp {yields}{pi}{sup +}{pi}{sup -} K{sub 1}{sup 0}K{sub 2}{sup 0} annihilations at 700-750 MeV/c. The values obtained are in good agreement with proceeding measurements. The mass has been measured with a high accuracy. (Author) 3 refs.

  13. Programmed Death Ligand 1 Expression Among 700 Consecutive Endometrial Cancers: Strong Association With Mismatch Repair Protein Deficiency.

    Science.gov (United States)

    Li, Zaibo; Joehlin-Price, Amy S; Rhoades, Jennifer; Ayoola-Adeola, Martins; Miller, Karin; Parwani, Anil V; Backes, Floor J; Felix, Ashley S; Suarez, Adrian A

    2018-01-01

    This study aims to determine the prevalence of programmed death ligand 1 (PD-L1) expression in endometrial carcinoma (EC) and determine clinical and pathological associations. Immunohistochemistry for PD-L1 was performed on sections of a triple-core tissue microarray of 700 ECs. Positive PD-L1 expression, defined as 1% of cells staining positive, was evaluated in tumor and stromal compartments. Using age-adjusted logistic regression, we estimated odds ratios and 95% confidence intervals for associations between PD-L1 expression (overall and by staining compartment) with clinical and tumor characteristics. Kaplan-Meier plots and log-rank tests were used to evaluate associations between PD-L1 expression and EC-specific survival. PD-L1 expression was observed in 100 cases (14.3%), including 27 (3.9%) with expression in tumor cells only, 35 (5.0%) with expression in both tumor cells and stroma, and 38 (5.4%) with expression in stroma only. Expression was observed in ECs of different histologic types. Tumors characterized by loss of mismatch repair proteins were significantly associated with tumoral PD-L1 expression (P < 0.0001), but not with stromal PD-L1 expression. Both tumoral and stromal PD-L1 expressions were associated with high-grade endometrioid histology, nonendometrioid histology, and lymphovascular space invasion. We observed no significant associations between PD-L1 expression and EC-specific survival. PD-L1 is expressed in a significant proportion of EC and is associated with mismatch repair deficiency, potentially representing a mechanism of tumor immune evasion and a therapeutic target in EC.

  14. Size Effect Studies of the Creep Behaviour of 20MnMoNi55 at Temperatures from 700 {sup o}C to 900 {sup o}C

    Energy Technology Data Exchange (ETDEWEB)

    Krompholz, K.; Groth, E.; Kalkhof, D

    2000-11-01

    One of the objectives of the REVISA project (REactor Vessel Integrity in Severe Accidents) is to assess size and scale effects in plastic flow and failure. This includes an experimental programme devoted to characterising the influence of specimen size, strain rate, and strain gradients at various temperatures. One of the materials selected was the forged reactor pressure vessel material 20 MnMoNi 55, material number 1.6310 (heat number 69906). Among others, a size effect study of the creep response of this material was performed, using geometrically similar smooth specimens with 5 mm and 20 mm diameter. The tests were done under constant load in an inert atmosphere at 700 {sup o}C, 800 {sup o}C, and 900 {sup o}C, close to and within the phase transformation regime. The mechanical stresses varied from 10 MPa to 30 MPa, depending on temperature. Prior to creep testing the temperature and time dependence of scale oxidation as well as the temperature regime of the phase transformation was determined. The creep tests were supplemented by metallographical investigations.The test results are presented in form of creep curves strain versus time from which characteristic creep data were determined as a function of the stress level at given temperatures. The characteristic data are the times to 5% and 15% strain and to rupture, the secondary (minimum) creep rate, the elongation at fracture within the gauge length, the type of fracture and the area reduction after fracture. From metallographical investigations the austenitic phase contents at different temperatures could be estimated. From these data also the parameters of the regression calculation (e.g. Norton's creep law) were obtained. The evaluation revealed that the creep curves and characteristic data are size dependent of varying degree, depending on the stress and temperature level, but the size influence cannot be related to corrosion or orientation effects or to macroscopic heterogeneity (position effect) of

  15. Age as a risk factor for acute mountain sickness upon rapid ascent to 3,700 m among young adult Chinese men.

    Science.gov (United States)

    Tang, Xu-Gang; Zhang, Ji-hang; Qin, Jun; Gao, Xu-bin; Li, Qian-ning; Yu, Jie; Ding, Xiao-han; Huang, Lan

    2014-01-01

    The aim of this study was to explore the relationship between age and acute mountain sickness (AMS) when subjects are exposed suddenly to high altitude. A total of 856 young adult men were recruited. Before and after acute altitude exposure, the Athens Insomnia Scale score (AISS) was used to evaluate the subjective sleep quality of subjects. AMS was assessed using the Lake Louise scoring system. Heart rate (HR) and arterial oxygen saturation (SaO2) were measured. Results showed that, at 500 m, AISS and insomnia prevalence were higher in older individuals. After acute exposure to altitude, the HR, AISS, and insomnia prevalence increased sharply, and the increase in older individuals was more marked. The opposite trend was observed for SaO2. At 3,700 m, the prevalence of AMS increased with age, as did severe AMS, and AMS symptoms (except gastrointestinal symptoms). Multivariate logistic regression analysis showed that age was a risk factor for AMS (adjusted odds ratio [OR] 1.07, 95% confidence interval [CI] 1.01-1.13, Psleep quality may be a contributor to increased AMS prevalence in older subjects.

  16. Residual stress effects on the K parameter of the fracture mechanics

    International Nuclear Information System (INIS)

    Soares, Maria da Conceiccao B. Vieira; Andrade, Arnaldo H. Paes de

    1996-01-01

    Compressive residual stresses are beneficial and improve resistance to fracture and crack growth. Residual stresses can be introduced in fabricated components by a variety of means and a number of methods such as laser surface treatment, cold expanded hole, and shot peening. Neutrons diffraction measurements of residual stress were performed at a pulsed neutron source (ISIS, Didcot, UK), on shot peened plates of nickel base superalloy Udimet 720 and titanium alloy IMI 834. The stress intensity factor (K) of residual stress was evaluated by finite element modeling and weight function method. Finite element modeling of a 2D plate with a single edge-notch was applied and, due to symmetry only half of the plate was actually modeled. The stress intensity factor (K) was evaluated for both case of remote tension stress and residual stress. Crack surface overlapping, which is physically unacceptable, was noted for small cracks under residual and boundary lading. Overlap correction was proposed and applied in order to obtain reliable values for (K). (author)

  17. Evolution of energy deposition processes in anthracene single crystal from photochemistry to radiation chemistry under excitation with synchrotron radiation from 3 to 700 eV

    International Nuclear Information System (INIS)

    Nakagawa, Kazumichi; Jin, Zhaohui; Shimoyama, Iwao; Miyake, Yasuyuki; Ueno, Madoka; Kishigami, Yoichi; Horiuchi, Hiroki; Tanaka, Masahito; Kaneko, Fusae; Nishimagi, Hironobu; Kobayashi, Hiroyuki; Kotani, Masahiro

    2008-01-01

    Absolute values of quantum yield Φ(hν) of singlet exciton formation in anthracene single crystals were measured as a function of photon energy hν, with the usage of synchrotron radiation (SR) in 3-700 eV region. Values of Φ(hν) were found to increase linearly for hν≥75 eV. For hν≤40 eV, values of Φ(hν) gave a wealth of structures and are not linear to hν. Because number of secondary electrons produced by radiation is thought to increase in proportional to the incident photon energy, it is natural to conclude that the radiation chemistry effect becomes dominant above 75 eV. On the other hand, values of Φ(hν) showed response due to resonance rather than linear dependence with hν, which implies that the photochemical effect is dominant below 40 eV

  18. Road construction impact of the landscape transformation during the last 700 years in N Poland

    Science.gov (United States)

    Slowinski, M. M.; Ott, F.; Obremska, M.; Theuerkauf, M.; Czaja, R.; Wulf, S.; Błaszkiewicz, M.; Brauer, A.

    2016-12-01

    From way back, connecting pathways play an essential role in human life and are fundamental for cultural and economic exchange. However, routes also had negative impacts on nearby settlements since they became important during war times for troop transports and may even have fostered the spread of epidemic diseases. Here, we present, for the first time, a high-resolution reconstruction of the impact of the construction of the trade route "Via Marchionis" on landscape evolution in N Poland since more than 700 years. This reconstruction is based on exploiting the annually laminated (varved) sediment record of the nearby located Lake Czechowskie. The route was built in the early 13th century and it initially led from Brandenburg to the Castle of the Teutonic Order in Malbork. In the first few centuries this track developed and became the key migratory route during the Middle Ages on the territory of Pomerania. Moving armed forces often expended and devastated the region and caused changes in sovereignty and population density, all of which resulted in changes in regional vegetation and erosion processes in the lake's catchment. Based on a 5-year resolution pollen resolution pollen record combined with sub-annual resolving μ-XRF element scanning and precise varve dating five phases of significantly lower human activity interrupted by phases of stronger human impact were distinguished. Comparing these data with historical sources revealed a clear impact of wars and deployment through armed forces in this region. The strongest declines in anthropogenic pressure on the landscape are clearly related to periods of war and subsequent regeneration in the periods between wars. Hence, it was the construction of the "Via Marchionis" that indirectly influenced the development of Pomeranian landscape mainly due to its role as pathway for armed forces. This study is a contribution to ICLEA (VH-VI-415) and REKLIM projects of the Helmholtz Association and NCN UMO-2015/17/B/ST10/03430.

  19. Investigations of the microstructural stability of wrought Ni-(Fe)-based syperalloys for steam turbine rotor application beyond 700 C; Untersuchungen der Strukturstabilitaet von Ni-(Fe)-Basislegierungen fuer Rotorwellen in Dampfturbinen mit Arbeitstemperaturen ueber 700 C

    Energy Technology Data Exchange (ETDEWEB)

    Seliga, T.

    2005-07-01

    There is a continuous trend to improve the efficiency of modern power plants with steam turbine require operating steam temperature from 700 to 720 C. For substantial parts like turbine rotors and discs this means increased requirements on the high temperature resistance, which can not longer be fulfilled by the presently used steel. As new materials for the components, which are thermo-mechanically loaded, only Ni-based superalloys are suitable for their fabrication, structure stability and thermo-mechanical characteristics. With view on creep and creep crack growth resistance as suitable candidates in the context a DFG research project wrought Ni-based superalloy Waspaloy and Ni-Fe-based alloy Inconel 706 were selected, which exhibited different hardening mechanisms. Waspaloy is a {gamma}'-hardened material with small portion of carbides on the grain boundaries. Inconel 706 is a particle hardened alloy with a very complex microstructure, it consists of {gamma}', {gamma}{sup ''}-particle, {eta}-phase und carbides. Concerning to their castability, forgeability, creep and creep crack growth and microstructural stability these candidate materials have been investigated and modelled. The knowledge about their long time stability of the microstructure, castability, forgeability and mechanical properties leads to the two new modification (Waspaloy{yields}DT750 and Inconel 706{yields}DT706). The modification of the Waspaloy to DT 750 served better castability (elimination of the Freckle formation). An improvement of the long-term stability of the microstructure was not necessary, by a changed heat treatment was reached a homogeneous, monomodale {gamma}'-particle distribution. The modification of Inconel 706 to DT 706 served to stabilize the {gamma}'-phase and to reduce of the {gamma}{sup ''} phase without suppressing the cellular {eta}-phase colonies on the grain boundaries. This work presents the test results for the structural

  20. Asymmetry of the cross section for the reaction. gamma. d. -->. pi. /sup 0/d with linearly polarized. gamma. rays at 500--700 MeV and at a c. m. angle theta(0 = 130/sup 0/

    Energy Technology Data Exchange (ETDEWEB)

    Adamyan, F.V.; Akopyan, G.G.; Vartapetyan, G.A.; Galumyan, P.I.; Grabskii, V.O.; Karapetyan, V.V.; Karapetyan, G.V.; Oktanyan, V.K.

    1984-06-25

    The asymmetry of the cross section (..sigma..) of the reaction ..gamma..d ..-->.. ..pi../sup 0/d induced by linearly polarized ..gamma.. rays has been measured at energies E..gamma.. = 500 MeV, E..gamma.. = 600, and E/sub ..gamma../ = 700 MeV at the c.m. angle theta(0 = 130/sup 0/. The results disagree with calculations in the impulse approximation. The results can be explained in a qualitative way by appealing to an /sup 3/F/sub 3/ (2.26-GeV) dibaryon resonance.

  1. THE DEVELOPMENT OF TECHNOLOGY OF THE CORE THERMO-MECHANICALLY HARDENED REINFORC-ING STEEL OF GRADE A700HW OF DIE-ROLLED SECTION NO 12, 14, 16 PRODUCTION ACCORDING TO REQUIREMENT OF FINNISH STANDARDS SFST1216 IN CONDITIONS OF SMALL-SECTION MILL 320 OF RUP «BMZ»

    Directory of Open Access Journals (Sweden)

    A. V. Rusalenko

    2009-01-01

    Full Text Available The development of technology of the core thermomechanically hardened reinforcing steel of grade А700HW of die-rolled section No 12, 14, 16 production according to requirement of Finnish standards SFST1216 in conditions of small-section mill 320 of RUP «BMZ» is given.

  2. Nuclear reactors situation in Japan after the major earthquake of March 11, 2011. March 13, 2011, 7:00 AM status; Situation des reacteurs nucleaires au Japon suite au seisme majeur survenu le 11 mars 2011 (13 mars 2011 - Point a 7h)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    This situation note is established according to the information gained on March 13, 2011, at 7:00 AM, by the crisis centre of the French institute of radiation protection and nuclear safety (IRSN). The situation of the reactors No. 1, 2 and 3 of the Fukushima I site is briefly presented with the progress of the accident management actions. (J.S.)

  3. Comparison of sizing effect of T700 grade carbon fiber on interfacial properties of fiber/BMI and fiber/epoxy

    International Nuclear Information System (INIS)

    Yao Lirui; Li Min; Wu Qing; Dai Zhishuang; Gu Yizhuo; Li Yanxia; Zhang Zuoguang

    2012-01-01

    Highlights: ► Carbon fiber sizings can react itself and with resin at high temperature. ► Sizings improve IFSS of carbon fiber/epoxy, but reduce that of BMI matrix. ► IFSS of carbon fiber/epoxy is larger than corresponding carbon fiber/BMI. ► Partially desized carbon fiber shows the effect of polymeric sizing component. ► The results are helpful for optimizing sizing agent of carbon fiber composites. - Abstract: This paper aims to study impact of sizing agents on interfacial properties of two T700 grade high strength carbon fibers with bismaleimide (BMI) and epoxy (EP) resin matrix. The fiber surface roughness and chemical properties are analyzed for sized, desized, and partially desized carbon fibers, using atom force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS), respectively. FTIR analysis indicates that the sizing agents are chemically reactive, and they can react with BMI and EP at high temperatures. The micro-droplet tests exhibit that the desized carbon fibers have lower interfacial strengths with EP than the sized fibers, however, for BMI matrix, opposite trend is revealed. This is consistent with the chemical reactions of the sizing agents with the EP and BMI resins, in which sufficient reactions are observed for the sizing/EP mixture, while only partial reactions are probed for the sizing/BMI mixture. Interestingly, un-extracted epoxy type sizing particles are observed on partially desized carbon fiber surface, which significantly improves the interfacial adhesion with EP matrix.

  4. Tensile strength and creep behaviour of austenitic stainless steel type 18Cr - 12Ni with niobium additions at 700°C

    Science.gov (United States)

    Sordi, V. L.; Bueno, L. O.

    2010-07-01

    The effect of niobium additions up to 2.36 wt% on the creep behavior of a series of seven extra low carbon 18Cr-12Ni austenitic stainless steels at 700°C has been investigated. Grain size and hardness measurements, hot tensile tests and constant stress creep tests from 90 to 180 MPa were carried out for each alloy, in the solution treated condition at 1050, 1200 and 1300°C followed by quench in water. The mechanical behavior at high temperature was related to the amount of NbC precipitation occurring during the tests. Solid solution and intermetallic compound effects were also considered. Creep data analysis was done to determine the parameters of the creep power-law equation dot epsilon = A.σn and the Monkman-Grant relation dot epsilon.tmR = K. Niobium-carbide precipitation in these steels reduces the secondary stage dependence of strain rate with applied stress, resulting in n-values which indicate the possibility of operation of various creep mechanisms. The creep strength during the secondary stage is primarily controlled by the amount of NbC available for precipitation. However, the rupture times increase progressively with niobium content, as the amount of undissolved carbide particles in grain boundaries and the Laves phase precipitation increase.

  5. A Near-Annual Record of Hurricane Activity From the Little Bahama Bank Over the Last 700 Years

    Science.gov (United States)

    Winkler, T. S.; van Hengstum, P. J.; Donnelly, J. P.; Sullivan, R.; Albury, N. A.

    2016-12-01

    Long-term and high-resolution records of hurricane activity that extend past the short observational record (8m vibracores collected with a Rossfelder P-3. The previous core analyzed (TPBH-C1, Continental Shelf Research, 2014) was likely obtained from the cave-area of the bluehole, and previous radiocarbon-dated bivalves deeper in the core were likely impacted by an old-carbon effect, casting doubt on the veracity of the previous age-model at this site. Recent overwash beds from Hurricane Jeanne (2004) and Hurricane Floyd (1999) are present at all coretops, and additional radiocarbon dating that includes terrestrial organic matter fragments indicates a near-annual sedimentation rate in the bluehole (>1cm yr-1), with the record spanning the last 700 years. Since 1866 CE, 12 hurricanes with wind speeds exceeding Category 2 on the Saffir-Simpson Scale (wind speeds 154-177 km hr-1) have passed within a 50 km radius of TPBH, many of which can be associated with coarse-grained overwash deposits in the top 200 cm of TPBH-C3. It appears from this high-resolution record that 1500-1650 CE and 1750-1800 CE were active intervals for hurricanes near Abaco, which were previously identified in a lower-resolution (multi-decadal) hurricane reconstruction from Abaco (Blackwood Sinkhole). Additionally, these active intervals coincide with evidence of regional storminess from multiple reconstructions based on historical archives (e.g.: Archivo General de Indias, newspapers, ships' logbooks, meteorological journals), and the 1500-1650 CE active interval falls within a previously identified 1400-1675 CE active interval of intense hurricane strikes on the Northeastern United States. Once the age-model is finalized, further comparison of this record to other regional oceanographic and high-resolution hurricane reconstructions may provide further insight into the drivers of hurricane activity during the last millennium.

  6. Systematic Analysis of Rocky Shore Morphology along 700km of Coastline Using LiDAR-derived DEMs

    Science.gov (United States)

    Matsumoto, H.; Dickson, M. E.; Masselink, G.

    2016-12-01

    Rock shore platforms occur along much of the world's coast and have a long history of study; however, uncertainty remains concerning the relative importance of various formative controls in different settings (e.g. wave erosion, weathering, tidal range, rock resistance, inheritance). Ambiguity is often attributed to intrinsic natural variability and the lack of preserved evidence on eroding rocky shores, but it could also be argued that previous studies are limited in scale, focusing on a small number of local sites, which restricts the potential for insights from broad, regional analyses. Here we describe a method, using LiDAR-derived digital elevation models (DEMs), for analysing shore platform morphology over an unprecedentedly wide area in which there are large variations in environmental conditions. The new method semi-automatically extracts shore platform profiles and systematically conducts morphometric analysis. We apply the method to 700 km of coast in the SW UK that is exposed to (i) highly energetic swell waves to local wind waves, (ii) macro to mega tidal ranges, and (iii) highly resistant igneous rocks to moderately hard sedimentary rocks. Computer programs are developed to estimate mean sea level, mean spring tidal range, wave height, and rock strength along the coastline. Filtering routines automatically select and remove profiles that are unsuitable for analysis. The large data-set of remaining profiles supports broad and systematic investigation of possible controls on platform morphology. Results, as expected, show wide scatter, because many formative controls are in play, but several trends exist that are generally consistent with relationships that have been inferred from local site studies. This paper will describe correlation analysis on platform morphology in relation to environmental conditions and also present a multi-variable empirical model derived from multi linear regression analysis. Interesting matches exist between platform gradients

  7. Determination of material behavior in 700 C turbine components under component and load specific conditions

    Energy Technology Data Exchange (ETDEWEB)

    Lueckemeyer, N.; Kirchner, H.; Kern, T.U. [Siemens AG, Muehlheim (Germany). Energy Sector; Reigl, M. [Alstom Power, Baden (Switzerland); Klenk, A.; Klein, T. [Stuttgart Univ. (Germany). MPA; Schwienheer, M.; Cui, L.; Scholz, A.; Berger, C. [Institut fuer Werkstoffkunde (IfW), Darmstadt (Germany)

    2010-07-01

    With global warming being one of mankind's greatest challenges, an increasing demand for electricity world-wide, and studies showing that fossil resources like coal and gas will remain a major source for electricity for the next couple of decades, research into the development of highest efficiency fossil power plants has become a top priority. Calculations for coal fired power plants have shown that CO{sub 2} emissions can be reduced by as much as 7% compared to the current state of the art equipment. It can be reached by increasing the live steam parameters to 700 C and 350bar. To achieve the desired operating hours at this temperature the application of nickel base materials is necessary for the main components such as rotors, inner casings and valves. Nowadays, the use of Nickel base alloys is common practice for selected gas turbine components. However, with steam turbine rotors being 1000mm in diameter and casings with wall thicknesses higher than 100mm the gas turbine application range and experience for nickel base alloys are well exceeded. This paper uses a basic design for a steam turbine to illustrate the core challenges in developing nickel based steam turbine components, such as casting, forging, nondestructive testing and welding. Suitable nickel based alloys have been investigated in research projects over the past years. The research results are summarized and an explanation is given as to why Alloy617 was selected for forged components and Alloy625 for cast components. This paper then focuses on the material behavior under long term and complex loading conditions and on the development of life time concepts for thick walled components made from these alloys. Due to the differences in the material behavior of nickel base alloys, the existing steel design philosophies cannot be completely adopted but rather must be carefully evaluated and modified where necessary. To do this, large test components were manufactured. Based on both standard tests

  8. SRC burn test in 700-hp oil-designed boiler. Annex Volume C. Boiler emission report. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    1983-09-01

    The Solvent-Refined Coal (SRC) test burn program was conducted at the Pittsburgh Energy Technology Center (PETC) located in Bruceton, Pa. One of the objectives of the study was to determine the feasibility of burning SRC fuels in boilers set up for fuel oil firing and to characterize emissions. Testing was conducted on the 700-hp oil-fired boiler used for research projects. No. 6 fuel oil was used for baseline data comparison, and the following SRC fuels were tested: SRC Fuel (pulverized SRC), SRC Residual Oil, and SRC-Water Slurry. Uncontrolled particulate emission rates averaged 0.9243 lb/10/sup 6/ Btu for SRC Fuel, 0.1970 lb/10/sup 6/ Btu for SRC Residual Oil, and 0.9085 lb/10/sup 6/ Btu for SRC-Water Slurry. On a lb/10/sup 6/ Btu basis, emissions from SRC Residual Oil averaged 79 and 78%, respectively, lower than the SRC Fuel and SRC-Water Slurry. The lower SRC Residual Oil emissions were due, in part, to the lower ash content of the oil and more efficient combustion. The SRC Fuel had the highest emission rate, but only 2% higher than the SRC-Water Slurry. Each fuel type was tested under variable boiler operating parameters to determine its effect on boiler emissions. The program successfully demonstrated that the SRC fuels could be burned in fuel oil boilers modified to handle SRC fuels. This report details the particulate emission program and results from testing conducted at the boiler outlet located before the mobile precipitator take-off duct. The sampling method was EPA Method 17, which uses an in-stack filter.

  9. Effect of predeformation on microstructural evolution of a Zr alloy during 550–700 °C aging after β quenching

    International Nuclear Information System (INIS)

    Chai, Linjiang; Luan, Baifeng; Murty, Korukonda L.; Liu, Qing

    2013-01-01

    In this paper, we report the effect of a 20% predeformation on the microstructural evolution of a Zr–0.85Sn–0.4Nb–0.4Fe–0.1Cr–0.05Cu alloy during aging between 550 and 700 °C after β quenching. Transmission electron microscopy, electron backscatter diffraction, electron channeling contrast and secondary electron imaging techniques are jointly utilized to carry out detailed microstructural characterization. By comparing microstructures between directly aged specimens (group A) and specimens aged after a 20% predeformation (group B), it is revealed that the introduced predeformation could exert remarkable influences on the Zr alloy. As the aging temperature and/or time increase, initial plate structures finally recrystallize in both groups. In spite of the similarity of the general evolution profile, the predeformation introduced in group B evidently reduces the required aging temperature and time. Distinct recrystallization nucleation behaviors due to different recrystallization mechanisms are also found in both groups. Noticeable differences between the with- and without-predeformation groups also include grain size, distribution of second-phase particles and misorientation angle distribution features in recrystallized specimens. Reasons accounting for the accelerated recrystallization and distinct microstructural characteristics in group B are discussed and attributed to the defects introduced during the predeformation. In addition, grain size calculation by applying the Zener equation shows that, although equilibrium states are not attained in both groups, the case with the predeformation is closer to the ideal equilibrium

  10. Evaluation of used methodology/methods in Aespoe HRL. Sections 0/700-1/475 and 1/475-2/265

    International Nuclear Information System (INIS)

    Andersson, Kjell; Sundquist, U.; Torssander, P.

    1997-01-01

    Some of the main objectives with the Aespoe Hard Rock Laboratory is reviewing and verifying the suitability of different investigations methods regarding bedrock characterization, test methods for detailed site investigations and to evaluate factors of importance for safety in realistic conditions. The SKB evaluation will result in a strategy planned to be used in the forthcoming site selection of a repository for high level radioactive waste. This report presents an evaluation of the methods used by SKB in the prediction of the bedrock prior to excavation. The prediction was based on the pre investigations carried out during 1986-1990. The review has followed the SKB classification of issue areas: geological/structural model, groundwater flow, groundwater chemistry, transport of solutes and mechanical stability. The review concerns SKB's objectives with the prediction and the different criteria for selection of variables - considering the demands of the performance assessment. This report includes evaluation of two tunnel sections, 0/700 - 1/475 and 1/475 - 2/265, comprising used data, prediction methods and prediction accuracy. By way of comparing predictions before excavation and outcome in the tunnel, a strict validation was performed. Based on the results from the validation, the applicability of different methods was estimated and the predictability of different subjects was assessed. It should be emphasised that the Aespoe predictions have not been directly intended for performance assessment purposes. However, it is of interest to see how the predictions relate to the information needs of performance assessment. By this it is possible to identify areas where more work needs to be done in the future, either in the operational phases at Aespoe or in other parts of the SKB program, thereby setting the predictions in an overall perspective from the point of view of performance assessment

  11. Impact of Medieval road construction on landscape transformation during the last 700 years in N Poland

    Science.gov (United States)

    Słowiński, Michał; Ott, Florian; Obremska, Milena; Theuerkauf, Martin; Czaja, Roman; Wulf, Sabine; Błaszkiewicz, Mirosław; Brauer, Achim

    2017-04-01

    The track "Via Marchionis" was established in the early 13th century and initially led from today's territory of Germany (city of Brandenburg) through the capital of Neumark (Myślibórz, 1298 AD) to The Castle of the Teutonic Order in Malbork (Poland, 1286 AD). It was one of the first main West-East connections in northern central Europe and functioned as a road until today. In the following centuries, this track became the key migration route during the Middle Ages in the territory of Pomerania. In particular, frequent wars in this region during the last millennium exerted great impact on the exchange of human population. Here, we present the first high-resolution reconstruction of the impact of the construction of the trade route "Via Marchionis" on landscape evolution since more than 700 years based on a varved lake sediment record from Lake Czechowskie, located in a distance of only a few hundred meters from the Via Marchionis. We established a high-resolution palaeoenvironmental reconstruction based on a pollen record at unprecedented 5-year resolution combined with sub-annual resolving μ-XRF element data of sediments and precise varve dating. As a result, five phases of significantly lower human pressure interrupted by phases of intensified human impact were distinguished. A comparison of these data with historical sources revealed a clear relation of vegetation changes and wars and deployment through armed forces in this region. The strongest declines in anthropogenic pressure on the landscape occurred during periods of war and the subsequent decades of regeneration. Our results suggest that moving of armed forces devastated the region and caused changes in sovereignty and population density, which in turn resulted in changes in regional vegetation and erosion processes in the lake's catchment. Therefore, we conclude that the construction of Via Marchionis was an indirect factor that constantly influenced changes of the Pomerania landscape since the 14th

  12. Effects of volcanic eruptions on China's monsoon precipitation over the past 700 years

    Science.gov (United States)

    Zhuo, Z.; Gao, C.

    2013-12-01

    Tropical volcanic eruptions were found to affect precipitation especially in Asia and Africa monsoon region. However, studies with different types of eruptions suggested different impacts as well as the spatial patterns. In this study, we combined the Monsoon Asia Drought Atlas (MADA, [Cook et al., 2010]) and the Chinese Historical Drought Disaster Index (CHDDI) compiled from the historic meteorological records to study the effect of volcanic eruptions on China's monsoon precipitation over the past 700 years. Histories of past volcanism were compiled from the IVI2[Gao et al., 2008] and Crowley2013[Crowley and Unterman, 2013] reconstructions. Volcanic events were classified into 2×Pinatubo, 1×Pinatubo , ≥5 Tg sulfate aerosols injection in the northern hemisphere (NH) stratosphere for IVI2; and NH sulfate flux more than 20/15/10/5 kg km-2 for Crowley2013. In both cases, average MADA show a drying trend over mainland China from year zero(0) to year three(+3) after the eruption; and the more sulfate aerosol injected into the NH stratosphere or the larger the sulfate flux, the more severe this drying trend seem to reveal. In comparison, a wetting trend was found in the eruption year with Southern Hemisphere (SH) only injections. Superposed epoch analysis with a 10,000 Monte Carlo resampling procedure showed that 97.9% (96.9%) of the observed MADA values are statistically significant at the 95% (99%) confidence level. The drying is probably caused by a reduction of the latent heat flux due to volcanic aerosol' cooling effect, leading to the weakening of south Asian monsoon and decrease of moisture vapor over tropical oceans, which contribute to a reduced moisture flux over china. Spatial distribution of the average MADA show a southward movement of the driest areas in eastern China from year zero to year three after the 1×Pinatubo and 2×Pinatubo eruptions, whereas part of north china experienced unusual wetting condition. This is in good agreement with CHDDI, which

  13. Tensile strength and creep behaviour of austenitic stainless steel type 18Cr - 12Ni with niobium additions at 700{sup 0}C

    Energy Technology Data Exchange (ETDEWEB)

    Sordi, V L; Bueno, L O, E-mail: sordi@ufscar.b [Federal University of Sao Carlos, Materials Engineering Department, Sao Carlos (SP), 13565-905 (Brazil)

    2010-07-01

    The effect of niobium additions up to 2.36 wt% on the creep behavior of a series of seven extra low carbon 18Cr-12Ni austenitic stainless steels at 700{sup 0}C has been investigated. Grain size and hardness measurements, hot tensile tests and constant stress creep tests from 90 to 180 MPa were carried out for each alloy, in the solution treated condition at 1050, 1200 and 1300{sup 0}C followed by quench in water. The mechanical behavior at high temperature was related to the amount of NbC precipitation occurring during the tests. Solid solution and intermetallic compound effects were also considered. Creep data analysis was done to determine the parameters of the creep power-law equation {epsilon}-dot = A.{sigma}{sup n} and the Monkman-Grant relation {epsilon}-dot .t{sup m}{sub R} = K. Niobium-carbide precipitation in these steels reduces the secondary stage dependence of strain rate with applied stress, resulting in n-values which indicate the possibility of operation of various creep mechanisms. The creep strength during the secondary stage is primarily controlled by the amount of NbC available for precipitation. However, the rupture times increase progressively with niobium content, as the amount of undissolved carbide particles in grain boundaries and the Laves phase precipitation increase.

  14. Neutron capture cross section measurement of $^{238}$U at the n_TOF CERN facility in the energy region from 1 eV to 700 keV

    CERN Document Server

    Mingrone, F; Vannini, G; Colonna, N; Gunsing, F; Zugec, P; Altstadt, S; Andrzejewski, J; Audouin, L; Barbagallo, M; Becares, V; Becvavr, F; Belloni, F; Berthoumieux, E; Billowes, J; Bosnar, D; Brugger, M; Calviani, M; Calvino, F; Cano-Ott, D; Carrapico, C; Cerutti, F; Chiaveri, E; Chin, M; Cortes, G; Cortes-Giraldo, M A; Diakaki, M; Domingo-Pardo, C; Duran, I; Dressler, R; Eleftheriadis, C; Ferrari, A; Fraval, K; Ganesan, S; Garcia, A R; Giubrone, G; Goncalves, I F; Gonzalez-Romero, E; Griesmayer, E; Guerrero, C; Hernandez-Prieto, A; Jenkins, D G; Jericha, E; Kadi, Y; Kappeler, F; Karadimos, D; Kivel, N; Koehler, P; Kokkoris, M; Krticka, M; Kroll, J; Lampoudis, C; Langer, C; Leal-Cidoncha, E; Lederer, C; Leeb, H; Leong, L S; Lo Meo, S; Losito, R; Mallick, A; Manousos, A; Marganiec, J; Martinez, T; Mastinu, P F; Mastromarco, M; Mendoza, E; Mengoni, A; Milazzo, P M; Mirea Horia, M; Mondalaers, W; Paradela, C; Pavlik, A; Perkowski, J; Plompen, A; Praena, J; Quesada, J M; Rauscher, T; Reifarth, R; Riego, A; Robles, M S; Rubbia, C; Sabate-Gilarte, M; Sarmento, R; Saxena, A; Schillebeeckx, P; Schmidt, S; Schumann, D; Tagliente, G; LTain, J; Tarrio, D; Tassan-Got, L; Tsinganis, A; Valenta, S; Variale, V; Vaz, P; Ventura, A; Vermeulen, M J; Vlachoudis, V; Vlastou, R; Wallner, A; Ware, T; Weigand, M; Weiss, C; Wright, T

    2016-01-01

    The aim of this work is to provide a precise and accurate measurement of the $^{238}$U(n,$\\gamma$) reaction cross section in the energy region from 1 eV to 700 keV. This reaction is of fundamental importance for the design calculations of nuclear reactors, governing the behaviour of the reactor core. In particular, fast reactors, which are experiencing a growing interest for their ability to burn radioactive waste, operate in the high energy region of the neutron spectrum. In this energy region most recent evaluations disagree due to inconsistencies in the existing measurements of up to 15%. In addition, the assessment of nuclear data uncertainty performed for innovative reactor systems shows that the uncertainty in the radiative capture cross-section of $^{238}$U should be further reduced to 1-3% in the energy region from 20 eV to 25 keV. To this purpose, addressed by the Nuclear Energy Agency as a priority nuclear data need, complementary experiments, one at the GELINA and two at the n_TOF facility, were pr...

  15. Conceptual design considerations for providing hook-up type schemes for tracking beyond design basis events (BDBE) for 700 MWe PHWR project

    International Nuclear Information System (INIS)

    Vhora, S.F.; Inder Jit; Bhardwaj, S.A.

    2005-01-01

    A broad review of major nuclear accidents such as Chernobyl reveals that provision of access to the reactor core for cooling purpose had to be made from outside the reactor building by tunneling. Also the NAPS fire incident could be mitigated once the fire water injection to the steam generators could be ensured. In this case the boiler room which was outside the primary containment was accessible relatively easily for mitigation after the initial period. Both of the above had accident scenarios which can be termed Beyond Design Basis (BDBE) since the accident initiation/scenario did not fit into the events under postulated initiating events (PIES) or Design Basis Events (DBEs). These accidents or events reveal that some sort of access to the core or the components inside the Reactor building becomes necessary. It is also to be noted that manual intervention beyond the initial period of half an hour or earlier in the Emergency operating procedure (EOP) is inevitably called for as a recovery action in order to mitigate the severity and minimize long term consequences. This paper attempts to discuss the type of concepts which can give access to the core or associated systems which can then provide continued heat sink. The discussions would include the criteria for design of such concepts and give examples of such concepts already implemented and proposes schemes to be implemented in the 700 MWe Project. (author)

  16. Reconstructing the role of landuse change on water yield at the Maya urban center Tikal, Guatemala [700-800 AD

    Science.gov (United States)

    Shu, L.; Duffy, C.; French, K. D.; Murtha, T., Jr.; Garcia-Gonzalez, S. E.

    2014-12-01

    In recent years scientists have been debating the role of climate on the trajectory of Maya culture in the Late Classic period, 600-900 AD. Paleo-climatologists have reconstructed realizations of climate [Haug 2003; Medina-Elizalde 2012; Hodell 1995] that offer evidence for reduced precipitation in the Late Classic period. Recently French et al [2014] proposed that landuse change may also play an important role in the available water supply at Tikal, with the removal of tropical forest and conversion to maize-agriculture and urban landuse leading to extensive development of sophisticated water storage systems and rainfall harvesting for water supply and irrigation. Rapid population growth is a concurrent and compounding factor [Scarborough 2012; Shaw 2003] where landuse impacts the distribution and availability of water storage in the surrounding watershed. Although proposed climate scenarios for the Late Classic offer a quantitative scenario for possible atmospheric conditions at Tikal, the impact of land use change on the distribution and availability of water supply has not been evaluated. In this research we reconstruct the plausible vulnerability of the water supply at Tikal under the combined forces of climatic and land use change. The Penn State Integrated Hydrologic Model (PIHM) [Qu and Duffy 2007] is used to simulate the daily-to-seasonal space and time distribution of soil moisture, groundwater and surface water storage for the period 700-800 AD, the peak of Tikal's population history. The analysis includes a quantitative assessment of the likely changes in available water storage as tropical forest is converted to maize agriculture and urban land. In particular we examine the important control that reduced canopy interception plays in the seasonal availability of water. Preliminary simulations suggest that removing tropical forest increases runoff and available water storage, which may serve to moderate seasonal and long-term drought conditions.

  17. Oxidation behaviour of ferritic stainless steel grade Crofer 22 APU at 700 °C in flowing Ar−75%CO{sub 2}−12%H{sub 2}O

    Energy Technology Data Exchange (ETDEWEB)

    Shariff, Nurul Atikah; Othman, Norinsan Kamil [School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Jalar, Azman [Institute of Micro Engineering and Nanoelectronics (IMEN), Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia)

    2013-11-27

    The oxidation of Ferritic Stainless Steel (FSS) grade Crofer 22 APU has been investigated. FSS alloys were exposed to isothermal conditions in a horizontal tube furnace at a 700 °C in flowing Ar−75%CO{sub 2}−12%H{sub 2}O at a pressure of approximately 1 atm. The results showed that the growth of non protective Fe{sub 2}O{sub 3} and spinel was observed after 50 h exposure in the presence of 12% H{sub 2}O. The weight was increased significantly with time of exposure. The formation of different oxides is presented on the interface of the specimen such as MnCr{sub 2}O{sub 4}, Fe{sub 3}O{sub 4} and Fe{sub 2}O{sub 3} were revealed by X-ray diffraction and supported by EDAX analysis. FSS did not form a protective Cr{sub 2}O{sub 3} layer due to water vapour accelerates the kinetics oxidation. Data of microstructure observation is presented and discussed in this paper in term of water vapour effects.

  18. Correlations and adsorption mechanisms of aromatic compounds on biochars produced from various biomass at 700 °C.

    Science.gov (United States)

    Yang, Kun; Jiang, Yuan; Yang, Jingjing; Lin, Daohui

    2018-02-01

    Knowledge of adsorption behavior of organic contaminants on high heat temperature treated biochars is essential for application of biochars as adsorbents in wastewater treatment and soil remediation. In this study, isotherms of 25 aromatic compounds adsorption on biochars pyrolyzed at 700 °C from biomass including wood chips, rice straw, bamboo chips, cellulose, lignin and chitin were investigated to establish correlations between adsorption behavior and physicochemical properties of biochars. Isotherms were well fitted by Polanyi theory-based Dubinin-Ashtakhov (DA) model with three parameters, i.e., adsorption capacity (Q 0 ) and adsorption affinity (E and b). Besides the negative correlation of Q 0 with molecular maximum cross-sectional areas (σ) of organic compounds, positive correlations of Q 0 with total pore volume (V total ) and average diameter of micropore (D) of biochars were observed, indicating that adsorption by biochars is captured by the pore-filling mechanism with molecular sieving effect in biochar pores. Linear solvation energy relationships (LSERs) of adsorption affinity (E) with solvatochromic parameters of organic compounds (i. e., α m and π ∗ ) were established, suggesting that hydrophobic effect, π-π interaction and hydrogen-bonding interaction are the main forces responsible for adsorption. The regression coefficient (π 1 ) and intercept (C) of obtained LSERs are correlated with biochar H/C and R micro , respectively, implying that biochars with higher aromaticity and more micropores have stronger π-π bonding potential and hydrophobic effect potential with aromatic molecule, respectively. However, hydrogen-bonding potential of biochars for organic molecules is not changed significantly with properties of biochars. A negative correlation of b with biochar H/C is also obtained. These correlations could be used to predict the adsorption behavior of organic compounds on high heat temperature treated biochars from various biomass for

  19. The independence of international civil servants during the neoliberal decades: implications of the work stoppage involving 700 staff of the World Health Organization in November 2005.

    Science.gov (United States)

    Katz, Alison

    2008-01-01

    The independence of international civil servants is critical to the fulfillment of their organizations' mandates, but it has been seriously undermined during 25 years of neoliberal influence in U.N. agencies, including the World Health Organization. In November 2005, 700 staff at WHO headquarters participated in a one-hour work stoppage--the first industrial action in the organization's history. Hierarchical and arbitrary management, abuse of rules and procedures, nepotism and harassment, and undue influence of international financial institutions, powerful member states, and transnational corporations have exhausted morale and motivation, creating a conformist environment and interfering with technical health work. In the neoliberal era, WHO staff confront conflicting duties of loyalty to a handful of member states and their private interests and loyalty to WHO's constitutional mandate. International civil servants need support from governing bodies and from the world's people in finding the correct balance. A first essential step would be respect for international labor standards within the U.N. family and, in particular, negotiation status and collective bargaining--human rights in the workplace and prerequisites for staff independence, integrity, and competence, qualities required to serve the world's people.

  20. The use of TLD-700H dosemeters in the assessment of external doses at the former Semipalatinsk nuclear test site.

    Science.gov (United States)

    Hill, P; Dederichs, H; Pillath, J; Schlecht, W; Hille, R; Artemev, O; Ptitskaya, L; Akhmetov, M

    2002-01-01

    The joint projects performed since 1995 by the Jülich Research Centre in co-operation with the Kazakh National Nuclear Centre in the area of the former nuclear test site near Semipalatinsk, in eastern Kazakhstan, have assessed the current dose rate of the population at and around the test site, as well as determining retrospectively the dose rate of persons affected by the atmospheric tests. Measurements of the population by personal dosemeters depend on reliably wearing these dosemeters over prolonged periods of time, and of a sufficient dosemeter return. In the past, such measurements have been particularly successful whenever short wearing times were possible. This requires high sensitivity of the dosemeters. The suitability of the highly sensitive TLD material of the BICRON TLD 700H type for such personal dosimetry measurements was investigated. It was tested in practical field application at the Semipalatinsk nuclear test site in September 2000. Initial results are available from individual doses received by a group of geologists and a group of herdsmen at the test site. For the first time, the individual dose was measured directly in these population groups. Detection limits below 1 microSv permit informative measurements for wearing times of less than two weeks. Most individual doses did not arise significantly out of local fluctuations of natural background. A conservative assessment from the aspect of practical health physics yielded a mean personal dose of 0.55 microSv per day for the herdsmen, whereas the geologists received a mean personal dose of 0.45 microSv per day. For an annual exposure period of typically, about three months, the radiation dose received by the persons investigated, in addition to the natural radiation exposure, is thus well below the international limit value of 1 mSv x a(-1) for the population dose.

  1. Nuclear reactors situation in Japan after the major earthquake of March 11, 2011. March 16, 2011, 7:00 PM status; Situation des reacteurs nucleaires au Japon suite au seisme majeur survenu le 11 mars 2011. Point de situation du 16 mars 2011 a 19 heures

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    This situation note is established according to the information gained on March 16, 2011, at 7:00 PM, by the crisis centre of the French institute of radiation protection and nuclear safety (IRSN). The situation of all 6 reactors of the Fukushima I site (Dai-ichi) and of their spent fuel pools, as well as the situation of the reactors No. 1, 2, 3 and 4 of the Fukushima II site (Daini), and of the Onagawa and Tokai power plants is briefly presented with the progress of the accident management actions. (J.S.)

  2. Age as a risk factor for acute mountain sickness upon rapid ascent to 3,700 m among young adult Chinese men

    Directory of Open Access Journals (Sweden)

    Tang XG

    2014-08-01

    Full Text Available Xu-gang Tang,1 Ji-hang Zhang,1 Jun Qin,1 Xu-bin Gao,1 Qian-ning Li,2 Jie Yu,1 Xiao-han Ding,1 Lan Huang1 1Institute of Cardiovascular Diseases, 2Department of Neurology, Xinqiao Hospital, Third Military Medical University, Chongqing, People’s Republic of China Background: The aim of this study was to explore the relationship between age and acute mountain sickness (AMS when subjects are exposed suddenly to high altitude.Methods: A total of 856 young adult men were recruited. Before and after acute altitude exposure, the Athens Insomnia Scale score (AISS was used to evaluate the subjective sleep quality of subjects. AMS was assessed using the Lake Louise scoring system. Heart rate (HR and arterial oxygen saturation (SaO2 were measured.Results: Results showed that, at 500 m, AISS and insomnia prevalence were higher in older individuals. After acute exposure to altitude, the HR, AISS, and insomnia prevalence increased sharply, and the increase in older individuals was more marked. The opposite trend was observed for SaO2. At 3,700 m, the prevalence of AMS increased with age, as did severe AMS, and AMS symptoms (except gastrointestinal symptoms. Multivariate logistic regression analysis showed that age was a risk factor for AMS (adjusted odds ratio [OR] 1.07, 95% confidence interval [CI] 1.01–1.13, P<0.05, as well as AISS (adjusted OR 1.39, 95% CI 1.28–1.51, P<0.001.Conclusion: The present study is the first to demonstrate that older age is an independent risk factor for AMS upon rapid ascent to high altitude among young adult Chinese men, and pre-existing poor subjective sleep quality may be a contributor to increased AMS prevalence in older subjects. Keywords: acute mountain sickness, age, Athens Insomnia Scale, rapid ascent, sleep

  3. A 700 year record of combustion-derived pollution in northern Spain: Tools to identify the Holocene/Anthropocene transition in coastal environments

    International Nuclear Information System (INIS)

    Leorri, Eduardo; Mitra, Siddhartha; Irabien, María Jesús; Zimmerman, Andrew R.; Blake, William H.; Cearreta, Alejandro

    2014-01-01

    There is an uneven geographical distribution of historic records of atmospheric pollutants from SW Europe and those that exist are very limited in temporal extent. Alternative data source is required to understand temporal trends in human impacts on atmospheric pollution. Polycyclic aromatic hydrocarbons (PAHs), heavy metal content and stable Pb isotopic ratios in a sediment core from a salt marsh in northern Spain were used to reconstruct the regional history of contaminant inputs over the last 700 years. Pre-1800s concentrations of Pb and PAHs represented baseline concentrations, i.e. pre-Industrial, conditions. During the initial stages of the Industrial Revolution, 1800s to 1860s, PAH concentrations increased by a factor of about two above baseline levels in the sediment column. By the 1930s, PAH levels reached ca. 10 times pre-Industrial levels and, along with Pb, reached a peak at ca. 1975 CE. Since then, sedimentary PAH and Pb concentrations decreased significantly. A combination of PAH isomer and Pb stable isotope ratios suggests that the contaminant sources are regional, likely derived partially from wood, but mainly coal used by the metallurgic industry in the Basque country since the 1800s and until the 1970s when leaded petrol saw increased use. This chronology of regional atmosphere-derived pollution expands current southwest Europe emission records and shows coastal salt marsh sediments to be useful in reconstructing the Anthropocene. - Highlights: • Historic records of atmospheric pollutant emissions in SW Europe are needed. • PAH and Pb concentrations and ratios from a north Spain salt marsh core were used. • Atmosphere emissions mainly from regional coal burning increased in the early 1800s. • Emissions associated with leaded gasoline peaked in 1975 CE. • The results suggest 1800 CE as the Holocene/Anthropocene transition

  4. A 700 year record of combustion-derived pollution in northern Spain: Tools to identify the Holocene/Anthropocene transition in coastal environments

    Energy Technology Data Exchange (ETDEWEB)

    Leorri, Eduardo, E-mail: leorrie@ecu.edu [Department of Geological Sciences, East Carolina University, Graham Building 103B, Greenville, NC 27858 (United States); Mitra, Siddhartha, E-mail: mitras@ecu.edu [Department of Geological Sciences, East Carolina University, Graham Building 103B, Greenville, NC 27858 (United States); Irabien, María Jesús, E-mail: mariajesus.irabien@ehu.es [Departamento de Mineralogía y Petrología, Facultad de Ciencia y Tecnología, Universidad del País Vasco UPV/EHU, Apartado 644, 48080 Bilbao (Spain); Zimmerman, Andrew R., E-mail: azimmer@ufl.edu [Department of Geological Sciences, University of Florida, 241 Williamson Hall, P.O. Box 112120, Gainesville, FL 32611 (United States); Blake, William H., E-mail: william.blake@plymouth.ac.uk [Consolidated Radioisotope Facility, University of Plymouth, Plymouth (United Kingdom); Cearreta, Alejandro, E-mail: alejandro.cearreta@ehu.es [Departamento de Estratigrafía y Paleontología, Facultad de Ciencia y Tecnología, Universidad del País Vasco UPV/EHU, Apartado 644, 48080 Bilbao (Spain)

    2014-02-01

    There is an uneven geographical distribution of historic records of atmospheric pollutants from SW Europe and those that exist are very limited in temporal extent. Alternative data source is required to understand temporal trends in human impacts on atmospheric pollution. Polycyclic aromatic hydrocarbons (PAHs), heavy metal content and stable Pb isotopic ratios in a sediment core from a salt marsh in northern Spain were used to reconstruct the regional history of contaminant inputs over the last 700 years. Pre-1800s concentrations of Pb and PAHs represented baseline concentrations, i.e. pre-Industrial, conditions. During the initial stages of the Industrial Revolution, 1800s to 1860s, PAH concentrations increased by a factor of about two above baseline levels in the sediment column. By the 1930s, PAH levels reached ca. 10 times pre-Industrial levels and, along with Pb, reached a peak at ca. 1975 CE. Since then, sedimentary PAH and Pb concentrations decreased significantly. A combination of PAH isomer and Pb stable isotope ratios suggests that the contaminant sources are regional, likely derived partially from wood, but mainly coal used by the metallurgic industry in the Basque country since the 1800s and until the 1970s when leaded petrol saw increased use. This chronology of regional atmosphere-derived pollution expands current southwest Europe emission records and shows coastal salt marsh sediments to be useful in reconstructing the Anthropocene. - Highlights: • Historic records of atmospheric pollutant emissions in SW Europe are needed. • PAH and Pb concentrations and ratios from a north Spain salt marsh core were used. • Atmosphere emissions mainly from regional coal burning increased in the early 1800s. • Emissions associated with leaded gasoline peaked in 1975 CE. • The results suggest 1800 CE as the Holocene/Anthropocene transition.

  5. 25 CFR 700.251 - Fees.

    Science.gov (United States)

    2010-04-01

    ... international organizations when to do so without charge is an appropriate courtesy, or when the recipient is... established business custom (e.g., furnishing personal reference data to prospective employers of former...

  6. 25 CFR 700.257 - Definitions.

    Science.gov (United States)

    2010-04-01

    ....C. 552a. (b) Individual. As used in this subpart, “individual” means a citizen of the United States... the Commission including, but not limited to, education, financial transactions, medical history, and... photograph. (e) System of records. As used in this subpart, “System of records” means a group of any records...

  7. 25 CFR 700.805 - Definitions.

    Science.gov (United States)

    2010-04-01

    ... flaked ground or pecked stone); (iv) By products, waste products, or debris resulting from manufacture or..., reservoirs, horticultural/agricultural gardens or fields, bedrock mortars, or grinding surfaces, rock...

  8. 15 CFR 700.93 - Communications.

    Science.gov (United States)

    2010-01-01

    ... INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS DEFENSE... Office of Strategic Industries and Economic Security, Room 3876, U.S. Department of Commerce, Washington...

  9. 15 CFR 700.8 - Definitions.

    Science.gov (United States)

    2010-01-01

    ... used on production equipment, lubricants, cleaners, chemicals and other expendable items. (d) MRO does... Section 702 of the Defense Production Act (excepting the definition of “industrial resources”) and Section... Homeland Security, under the authority of the Defense Production Act, the Stafford Act, and Executive Order...

  10. 25 CFR 700.453 - Definitions.

    Science.gov (United States)

    2010-04-01

    ... a noncash contribution as described in attachment F of OMB Circular A-102. (f) Local government means a local unit of government including specifically a county, municipality, city, town, township...

  11. 24 CFR 700.105 - Definitions.

    Science.gov (United States)

    2010-04-01

    ... must be mobile. The mobility requirement does not exclude persons in wheelchairs or those requiring mobility devices.) (2) Each of the Activities of Daily Living noted in paragraph (1) of this definition... non-medical supervision, wellness programs, preventive health screening, monitoring of medication...

  12. 40 CFR 35.700 - Purpose.

    Science.gov (United States)

    2010-07-01

    ... surveys of geographic areas or classes of buildings (such as public buildings, school buildings, high-risk... management system for information concerning radon occurrence, levels, and programs; (ix) Payment of costs of... Consortia participation in the Environmental Protection Agency Home Evaluation Program; and (x) A toll-free...

  13. 12 CFR 700.2 - Definitions.

    Science.gov (United States)

    2010-01-01

    ...) The probability of a further potential loss to the insurance fund is negligible. (2) For purposes of...” for purposes of the Central Liquidity Facility is defined in § 725.2(o) of this chapter. (g) Regional...

  14. 31 CFR 700.13 - Nondiscrimination.

    Science.gov (United States)

    2010-07-01

    ... race, color, religion, national origin, sex, sexual orientation, age, or disability, Sexual harassment is a form of sex discrimination and is expressly prohibited. (b) Appropriate action will be taken against any person who violates any discrimination prohibition contained in paragraph (a) of this section...

  15. 25 CFR 700.247 - Appeals.

    Science.gov (United States)

    2010-04-01

    ... envelope containing the notice of appeal and the face of the notice shall bear the legend “FREEDOM OF INFORMATION APPEAL”. The failure of an appeal to bear such a legend will not disqualify an appeal from...

  16. 25 CFR 700.507 - Responsibilities.

    Science.gov (United States)

    2010-04-01

    ... OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES Employee... restrictions. (4) The Executive Director shall ensure that disciplinary or remedial action is taken in the case... supervisors who fail to carry out their responsibilities in taking disciplinary or remedial action in such...

  17. Radioimmunotherapy [INIS-UY-GEO--700

    International Nuclear Information System (INIS)

    Cacchione, R.

    2015-01-01

    This presentation is about the radiotherapy, chemo-immunotherapy and radioimmunotherapy treatment. Its adequate response in Non-Hodgkin Lymphoma as well as the tolerance and reversibly hematologic toxicity

  18. 9 CFR 93.700 - Definitions.

    Science.gov (United States)

    2010-01-01

    ...) Parts of several national entities combined into an area; or (4) A group of national entities (countries... Virgin Islands of the United States, and all other territories and possessions of the United States. [55...

  19. What does it take to create an effective and interactive learning environment with 700 students in a college Gen. Ed. Astro Course?

    Science.gov (United States)

    Prather, Edward E.; Brissenden, G.; Cormier, S.; Eckenrode, J.; Collaboration of Astronomy Teaching Scholars CATS

    2012-01-01

    College-level general education (gen ed.) curricula in the US have many goals: exposing students to the breadth of human ideas; elevating their reading comprehension, writing abilities, critical reasoning skills; and providing an understanding of, and appreciation for, subjects outside of their chosen field of study. Unfortunately the majority of the teaching and learning for gen ed. courses takes place in large enrollment courses. In the wake of the recent US financial crisis, many institutions of higher learning face extreme budget cuts, leading many faculty to teach in substantially larger classes with increasingly fewer resources. At the University of Arizona this issue manifests itself in mega-classes with enrollments from 700-1400. We discuss key programmatic and pedagogical changes involved in successfully implementing proven collaborative learning strategies into an Astro 101 mega-class. From devising new ways to hand out and collect papers, to altering course seating, to outlawing cell phones and laptops, to implementing new ways of administering tests. We take a "what ever it takes” approach to engineering this mega-course environment so it can succeed as a learner-centered classroom. Paramount to the success of this course has been the creation of the new CAE Ambassadors program which advances the leadership role of prior non-science majors along the continuum from student, to teaching assistant, to science education researcher, to STEM minor. This material is based in part upon work supported by the National Science Foundation under Grant No. 0715517, a CCLI Phase III Grant for the Collaboration of Astronomy Teaching Scholars (CATS). Any opinions, findings, and conclusions or recommendations expressed in this material are those of the authors and do not necessarily reflect the views of the National Science Foundation.

  20. Use of MCNP to compare the response of dose deposited in the TLD 100, TLD 600 and TLD 700 in radiation fields due to {sup 60}Co and {sup 241}AmBe source; Uso do MCNP para comparacao das respostas de dose depositada nos TLD 100, TLD 600 e TLD 700 em campos de irradiacao devido a fontes de {sup 60}Co e {sup 241}AmBe

    Energy Technology Data Exchange (ETDEWEB)

    Cavalieri, Tassio A.; Castro, Vinicius A.; Siqueira, Paulo T.D., E-mail: tassio.cavalieri@usp.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2012-08-15

    The successes of Boron Neutron Capture Therapy (BNCT) depend on the ability to deliver an adequate irradiation field to the target cells. Neutron beams used in BNCT are mostly driven from reactors and therefore, not only have a neutron energy range which far exceeds the thermal region but also do have a great gamma component. Beam characterization and dosimetry are consequently one of the essential procedures to be overcome to properly apply this technique. One of the methods currently used in mixed field (field containing both neutron and gamma) characterization, lies on the use of a pair of detectors with distinct responses to each beam component. But this technique needs to be better understood of how each thermoluminescent dosimeter (TLD) behaves in a mixed field or in a pure field. This work presents the results of a set of simulations performed in order to analyze the response of three ordinary types of TLDs - TLD 100, TLD 600 and TLD 700 - submitted to different irradiation fields from a Cobalt source and an Americium-Beryllium source inside a paraffin disk. And is also a possible method for performing the selection and calibration of theses TLDs. (author)

  1. Corrosion Performance of AISI-309 Exposed to Molten Salts V2O5-Na2SO4 at 700°C Applying EIS and Rp Electrochemical Techniques

    Directory of Open Access Journals (Sweden)

    E. F. Diaz

    2015-01-01

    Full Text Available The corrosion performance of AISI-309 exposed 5 days to molten salts 50 mol% V2O5-50 mol% Na2SO4 at 700°C is reported in this paper. Such evaluation was made using three electrochemical techniques: potentiodynamic polarization curve (PC, electrochemical impedance spectroscopy (EIS, and linear polarization resistance (Rp. From PC, the Tafel slopes, Icorr, and Ecorr were obtained. From Nyquist and Bode plots, it was possible to determine two different stages; the first one showed just one loop, which indicated the initial formation of Cr2O3 layer over the metallic surface; after that, the dissolution of Cr2O3 formed a porous layer, which became part of the corrosion products; at the same time a NiO layer combined with sulfur was forming, which was suggested as the second stage, represented by two capacitive loops. EIS plots were in agreement with the physical characterization made from SEM and EDS analyses. Fitting of EIS experimental data allowed us to propose two electrical circuits, being in concordance with the corrosion stages. Parameters obtained from the simulation of EIS data are also reported. From the results, it was stated that AISI-309 suffered intergranular corrosion due to the presence of sulfur, which diffused to the metallic surface through a porous Cr2O3 layer.

  2. The 21,700 yr b.p. Lower Toluca Pumice Plinian Eruption of Nevado de Toluca Volcano (Mexico): Evidences of Magma Mixing Process as Triggering Mechanism.

    Science.gov (United States)

    Capra, L.; Arce, J.; Macias, J.

    2006-05-01

    Approximately 21,700 yr B.P., after a period of quiescence of 4800 yr, Nevado de Toluca volcano erupted, producing the Lower Toluca Pumice deposit. The activity generated a 24-km-high Plinian column that lasted ~11 h and dispersed 2.3 km3 (0.8 km3 dense rock equivalent) of tephra toward the NE, blanketing the Lerma basin, an area occupied today by the city of Toluca, with up to 5 cm of ash. Subsequent eruptive pulses were sub-Plinian in style, accompanied by phreatomagmatic explosions that emplaced surge deposits. Finally, the column collapsed toward the NE with the emplacement of a pumice flow deposit. The high vesicularity of the pumice from the basal Plinian layer, up to 83% by volume, indicates that exsolution was dominantly magmatic, and that pressurization of the magma chamber was probably due to a magma mixing process. Evidence for this includes the compositional range of juvenile products (from 55 to 65 wt% SiO2), as well as the presence of two types of plagioclase, one in equilibrium and the other one with disequilibrium textures and reverse zoning. This suggests input of an andesitic liquid into the dacitic magma chamber. Based on the eruptive record, the most likely future eruptive activity at Nevado de Toluca volcano will be Plinian. Although quiet for more than 3250 yr, Plinian activity could occur after a long period of quiescence, and it could represent a hazard for the entire Toluca basin, where more than one million people live today.

  3. Structural changes of radial forging die surface during service under thermo-mechanical fatigue

    International Nuclear Information System (INIS)

    Nematzadeh, Fardin; Akbarpour, Mohammad Reza; Kokabi, Amir Hosein; Sadrnezhaad, Seyed Khatiboleslam

    2009-01-01

    Radial forging is one of the modern open die forging techniques and has a wide application in producing machine parts. During operation at high temperatures, severe temperature change associated with mechanical loads and the resultant wearing of the die surface lead to intense variation in strain on the die surface. Therefore, under this operating condition, thermo-mechanical fatigue (TMF) occurs on the surface of the radial forging die. TMF decreases the life of the die severely. In the present research, different layers were deposited on a 1.2714 steel die by SMAW and GTAW, with a weld wire of UDIMET 520. The microstructure of the radial forging die surface was investigated during welding and service using an optical microscope and scanning electron microscope. The results revealed that, after welding, the structure of the radial forging die surface includes the γ matrix with a homogeneous distribution of fine semi-spherical carbides. The weld structure consisted mostly of columnar dendrites with low grain boundaries. Also, microstructural investigation of the die surface during operation showed that the weld structure of the die surface has remained without any considerable change. Only dendrites were deformed and broken. Moreover, grain boundaries of the dendrites were revealed during service.

  4. Effect of processing on microstructure and physical properties of three nickel-based superalloys with different hardening mechanisms

    Energy Technology Data Exchange (ETDEWEB)

    Strondl, Annika; Frommeyer, Georg [Department of Materials Technology, Max-Planck-Institut fuer Eisenforschung GmbH, Max-Planck-Strasse 1, D-40237 Duesseldorf (Germany); Klement, Uta [Department of Materials and Manufacturing Technology, Chalmers University of Technology, SE-412 96 Gothenburg (Sweden); Milenkovic, Srdjan; Schneider, Andre

    2012-07-15

    The nickel-based superalloys Inconel alloy 600, Udimet alloy 720, and Inconel alloy 718 were produced by electron beam melting (EBM), casting, and directional solidification (DS). The distance between dendrites and the size of the precipitates indicated the difference in solidification rates between the three processes. In this study, the solidification rate was fastest with EBM, closely followed by casting, whereas it was much slower with DS. In the directional solidified materials the <100> direction was the fastest and thus, preferred growth direction. The EBM samples show a sharp (001)[100] texture in the building direction and in the two scanning directions of the electron beam. Macrosegregation was observed in some cast and directionally solidified samples, but not in the EBM samples. The melting temperatures are in good agreement with literature and the narrow melting interval of IN600 compare to UD720 and IN718 might reduce the risk of incipient melting during EBM processing. Porosity was observed in the EBM samples and the reasons are discussed. However, EBM seems to be a feasible process route to produce nickel-based superalloys with well-defined texture, no macrosegregation and a rapidly solidified microstructure. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  5. Reduction of renal uptake of 111In-DOTA-labeled and A700-labeled RAFT-RGD during integrin αvβ3 targeting using single photon emission computed tomography and optical imaging.

    Science.gov (United States)

    Briat, Arnaud; Wenk, Christiane H F; Ahmadi, Mitra; Claron, Michael; Boturyn, Didier; Josserand, Véronique; Dumy, Pascal; Fagret, Daniel; Coll, Jean-Luc; Ghezzi, Catherine; Sancey, Lucie; Vuillez, Jean-Philippe

    2012-06-01

    Integrin α(v)β(3) expression is upregulated during tumor growth and invasion in newly formed endothelial cells in tumor neovasculature and in some tumor cells. A tetrameric RGD-based peptide, regioselectively addressable functionalized template-(cyclo-[RGDfK])4 (RAFT-RGD), specifically targets integrin α(v)β(3) in vitro and in vivo. When labeled with indium-111, the RAFT-RGD is partially reabsorbed and trapped in the kidneys, limiting its use for further internal targeted radiotherapy and imaging investigations. We studied the effect of Gelofusine on RAFT-RGD renal retention in tumor-bearing mice. Mice were imaged using single photon emission computed tomography and optical imaging 1 and 24 h following tracer injection. Distribution of RAFT-RGD was further investigated by tissue removal and direct counting of the tracer. Kidney sections were analyzed by confocal microscopy. Gelofusine significantly induced a >50% reduction of the renal reabsorption of (111)In-DOTA-RAFT-RGD and A700-RAFT-RGD, without affecting tumor uptake. Injection of Gelofusine significantly reduced the renal retention of labeled RAFT-RGD, while increasing the tumor over healthy tissue ratio. These results will lead to the development of future therapeutic approaches. © 2012 Japanese Cancer Association.

  6. Neutron capture cross section measurement of 238U at the n TOF CERN facility with C6D6 scintillation detectors in the energy region from 1 eV to 700 keV

    CERN Document Server

    Mingrone, F.

    2017-01-01

    The aim of this work is to provide a precise and accurate measurement of the 238U(n,g) reaction cross section in the energy region from 1 eV to 700 keV. This reaction is of fundamental importance for the design calculations of nuclear reactors, governing the behaviour of the reactor core. In particular, fast reactors, which are experiencing a growing interest for their ability to burn radioactive waste, operate in the high energy region of the neutron spectrum. In this energy region most recent evaluations disagree due to inconsistencies in the existing measurements of up to 15%. In addition, the assessment of nuclear data uncertainty performed for innovative reactor systems shows that the uncertainty in the radiative capture cross-section of 238U should be further reduced to 1-3% in the energy region from 20 eV to 25 keV. To this purpose, addressed by the Nuclear Energy Agency as a priority nuclear data need, complementary experiments, one at the GELINA and two at the n_TOF facility, were proposed and carrie...

  7. A method to minimise the fading effects of LiF:Mg,Ti (TLD-600 and TLD-700) using a pre-heat technique.

    Science.gov (United States)

    Lee, YoungJu; Won, Yuho; Kang, Kidoo

    2015-04-01

    Passive integrating dosemeters [thermoluminescent dosimeter (TLD) and optically stimulated luminescence (OSL)] are the only legally permitted individual dosemeters for occupational external radiation exposure monitoring in Korea. Also its maximum issuing cycle does not exceed 3 months, and the Korean regulations require personal dosemeters for official assessment of external radiation exposure to be issued by an approved or rather an accredited dosimetry service according to ISO/IEC 17025. KHNP (Korea Hydro & Nuclear Power, LTD), a unique operating company of nuclear power plants (NPPs) in Korea, currently has a plan to extend a TLD issuing cycle from 1 to 3 months under the authors' fading error criteria, ±10%. The authors have performed a feasibility study that minimises post-irradiation fading effects within their maximum reading cycle employing pre-heating technique. They repeatedly performed irradiation/reading a bare TLD chip to determine optimum pre-heating conditions by analysing each glow curve. The optimum reading conditions within the maximum reading cycle of 3 months were decided: a pre-heating temperature of 165°C, a pre-heating time of 9 s, a heating rate of 25°C s(-1), a reading temperature of 300°C and an acquisition time of 10 s. The fading result of TLD-600 and TLD-700 carried by newly developed time temperature profile (TTP) showed a much smaller fading effect than that of current TTP. The result showed that the fading error due to a developed TTP resulted in a ∼5% signal loss, whereas a current TTP caused a ∼15% loss. The authors also carried out a legal performance test on newly developed TTP to confirm its possibility as an official dosemeter. The legal performance tests that applied the developed TTP satisfied the criteria for all the test categories. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  8. Early Evidence of Acheulean Settlement in Northwestern Europe - La Noira Site, a 700 000 Year-Old Occupation in the Center of France

    Science.gov (United States)

    Moncel, Marie-Hélène; Despriée, Jackie; Voinchet, Pierre; Tissoux, Hélène; Moreno, Davinia; Bahain, Jean-Jacques; Courcimault, Gilles; Falguères, Christophe

    2013-01-01

    The human settlement of Europe during Pleistocene times was sporadic and several stages have been recognized, both from paleaoanthropological and archaeological records. If the first phase of hominin occupation (as early as 1.4 Ma) seems mainly restricted to the southern part of the continent, the second phase, characterized by specific lithic tools (handaxes), is linked to Acheulean settlements and to the emergence of Homo heidelbergensis, the ancestor of Neanderthals. This phase reached northwestern Europe and is documented in numerous sites in Germany, Great Britain and northern France, generally after 600 ka. At la Noira (Brinay, Central France), the Middle Pleistocene alluvial formation of the Cher River covers an archaeological level associated with a slope deposit (diamicton). The lithic assemblage from this level includes Large Cutting Tools (LCTs), flakes and cores, associated with numerous millstone slabs. The lithic series is classified as Acheulean on the basis of both technological and typological analyses. Cryoturbation features indicate that the slope deposits and associated archaeological level were strongly frozen and disturbed after hominin occupation and before fluvial deposition. Eight sediment samples were dated by the electron spin resonance (ESR) method and the weighted average age obtained for the fluvial sands overlying the slope deposits is 665±55 ka. This age is older than previous chronological data placing the first European Acheulean assemblages north of 45th parallel north at around 500 ka and modifies our current vision of the initial peopling of northern Europe. Acheulean settlements are older than previously assumed and the oldest evidences are not only located in southern Europe. La Noira is the oldest evidence of Acheulean presence in north-western Europe and attests to the possibility of pioneering phases of Acheulean settlement which would have taken place on a Mode 1-type substratum as early as 700 ka. The lithic assemblage

  9. Early evidence of Acheulean settlement in northwestern Europe--la Noira site, a 700,000 year-old occupation in the center of France.

    Directory of Open Access Journals (Sweden)

    Marie-Hélène Moncel

    Full Text Available The human settlement of Europe during Pleistocene times was sporadic and several stages have been recognized, both from paleaoanthropological and archaeological records. If the first phase of hominin occupation (as early as 1.4 Ma seems mainly restricted to the southern part of the continent, the second phase, characterized by specific lithic tools (handaxes, is linked to Acheulean settlements and to the emergence of Homo heidelbergensis, the ancestor of Neanderthals. This phase reached northwestern Europe and is documented in numerous sites in Germany, Great Britain and northern France, generally after 600 ka. At la Noira (Brinay, Central France, the Middle Pleistocene alluvial formation of the Cher River covers an archaeological level associated with a slope deposit (diamicton. The lithic assemblage from this level includes Large Cutting Tools (LCTs, flakes and cores, associated with numerous millstone slabs. The lithic series is classified as Acheulean on the basis of both technological and typological analyses. Cryoturbation features indicate that the slope deposits and associated archaeological level were strongly frozen and disturbed after hominin occupation and before fluvial deposition. Eight sediment samples were dated by the electron spin resonance (ESR method and the weighted average age obtained for the fluvial sands overlying the slope deposits is 665±55 ka. This age is older than previous chronological data placing the first European Acheulean assemblages north of 45(th parallel north at around 500 ka and modifies our current vision of the initial peopling of northern Europe. Acheulean settlements are older than previously assumed and the oldest evidences are not only located in southern Europe. La Noira is the oldest evidence of Acheulean presence in north-western Europe and attests to the possibility of pioneering phases of Acheulean settlement which would have taken place on a Mode 1-type substratum as early as 700 ka. The

  10. Early evidence of Acheulean settlement in northwestern Europe--la Noira site, a 700,000 year-old occupation in the center of France.

    Science.gov (United States)

    Moncel, Marie-Hélène; Despriée, Jackie; Voinchet, Pierre; Tissoux, Hélène; Moreno, Davinia; Bahain, Jean-Jacques; Courcimault, Gilles; Falguères, Christophe

    2013-01-01

    The human settlement of Europe during Pleistocene times was sporadic and several stages have been recognized, both from paleaoanthropological and archaeological records. If the first phase of hominin occupation (as early as 1.4 Ma) seems mainly restricted to the southern part of the continent, the second phase, characterized by specific lithic tools (handaxes), is linked to Acheulean settlements and to the emergence of Homo heidelbergensis, the ancestor of Neanderthals. This phase reached northwestern Europe and is documented in numerous sites in Germany, Great Britain and northern France, generally after 600 ka. At la Noira (Brinay, Central France), the Middle Pleistocene alluvial formation of the Cher River covers an archaeological level associated with a slope deposit (diamicton). The lithic assemblage from this level includes Large Cutting Tools (LCTs), flakes and cores, associated with numerous millstone slabs. The lithic series is classified as Acheulean on the basis of both technological and typological analyses. Cryoturbation features indicate that the slope deposits and associated archaeological level were strongly frozen and disturbed after hominin occupation and before fluvial deposition. Eight sediment samples were dated by the electron spin resonance (ESR) method and the weighted average age obtained for the fluvial sands overlying the slope deposits is 665±55 ka. This age is older than previous chronological data placing the first European Acheulean assemblages north of 45(th) parallel north at around 500 ka and modifies our current vision of the initial peopling of northern Europe. Acheulean settlements are older than previously assumed and the oldest evidences are not only located in southern Europe. La Noira is the oldest evidence of Acheulean presence in north-western Europe and attests to the possibility of pioneering phases of Acheulean settlement which would have taken place on a Mode 1-type substratum as early as 700 ka. The lithic assemblage

  11. 75 FR 32790 - Discretionary Grant Program

    Science.gov (United States)

    2010-06-09

    ... Institute for Family Involvement FL 95,700 31-May-11. Parent to Parent of Georgia, Inc....... GA 95,700 31-May-11. Hawaii Pediatric Association Research & HI 95,700 31-May-11. Education Foundation. The Arc of... Education & Advocacy Leadership PA 95,700 31-May-11. Center. Rhode Island Parent Information RI 95,700 31...

  12. Dicty_cDB: Contig-U04770-1 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available m I P700 apoprot... 48 0.44 1 ( AY422592 ) Dictyota koreana IK24 photosystem I P700 apoprote... 48 0.44 1 ( AY422591 ) Dictyota korea...na IK23 photosystem I P700 apoprote... 48 0.44 1 ( AY422590 ) Dictyota korea...na IK22 photosystem I P700 apoprote... 48 0.44 1 ( AY422589 ) Dictyota koreana IK21 phot...osystem I P700 apoprote... 48 0.44 1 ( AY422588 ) Dictyota koreana IK20 photosystem I P700 apoprote... 48 0....44 1 ( AY422587 ) Dictyota koreana IK17 photosystem I P700 apoprote... 48 0.44 1 ( AY422586 ) Dictyota alter

  13. Nuclear reactors situation in Japan after the major earthquake of March 11, 2011. March 13, 2011, 7:00 PM status - updated at 11:00 PM; Situation des reacteurs nucleaires au Japon suite au seisme majeur survenu le 11 mars 2011. Point de situation du 13 mars 2011 a 19 heures - Mis a jour a 23 heures

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    This situation note is established according to the information gained on March 13, 2011, at 7:00 PM, by the crisis centre of the French institute of radiation protection and nuclear safety (IRSN). The situation of the reactors No. 1, 2 and 3 of the Fukushima I site (Dai-ichi), of the reactors No. 1, 2, 3 and 4 of the Fukushima II site (Daini), and of the Onagawa and Tokai power plants is briefly presented with the progress of the accident management actions. (J.S.)

  14. 25 CFR 700.557 - Political activity.

    Science.gov (United States)

    2010-04-01

    ... governments, even though such elections are not partisan in the usual meaning of the word. With respect to... petitions, posters, or other political materials during working hours or on Commission premises. (5) Engage...

  15. 29 CFR 541.700 - Primary duty.

    Science.gov (United States)

    2010-07-01

    ... other types of duties; the amount of time spent performing exempt work; the employee's relative freedom... employees for the kind of nonexempt work performed by the employee. (b) The amount of time spent performing.... Thus, employees who spend more than 50 percent of their time performing exempt work will generally...

  16. 24 CFR 700.130 - Service coordinator.

    Science.gov (United States)

    2010-04-01

    ... professional relationships with all agencies and service providers in the community, and develop a directory of...) Maintain necessary case files on each program participant, containing such information and kept in such...) Assist the grant recipient in building informal support networks with neighbors, friends and family; and...

  17. 32 CFR 700.922 - Shore patrol.

    Science.gov (United States)

    2010-07-01

    ... area that can absorb them without danger of disturbance or disorder, the senior officer present shall cause to be established, temporarily or permanently, in charge of an officer, a sufficient patrol of officers, petty officers, and noncommissioned officers to maintain order and suppress any unseemly conduct...

  18. 16 CFR 700.3 - Written warranty.

    Science.gov (United States)

    2010-01-01

    ... will not construe the Act to impede information disclosure in product advertising or labeling. 1 A... the consumer nor brought to the consumer's attention in connection with the sale. Such warranties are...

  19. 15 CFR 700.72 - Compulsory process.

    Science.gov (United States)

    2010-01-01

    ... OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS..., in the judgment of the Director of the Office of Strategic Industries and Economic Security, U.S. Department of Commerce, in consultation with the Chief Counsel for Industry and Security, U.S. Department of...

  20. 25 CFR 700.239 - Records available.

    Science.gov (United States)

    2010-04-01

    ... compiled by a criminal law enforcement authority in the course of a criminal investigation, or by an agency conducting a lawful national security intelligence investigation, confidential information furnished only by... by preparing a new computer program, nor are records required to be created to provide the requester...

  1. 25 CFR 700.722 - Grazing associations.

    Science.gov (United States)

    2010-04-01

    ... recognition by the Commissioner are: (1) The members of the association must be grazing permittees and.... (d) The Commissioner may withdraw his recognition of the association whenever: (1) The majority of... constitution and bylaws. All of the association's livestock will be run under an association brand properly...

  2. 24 CFR 700.145 - Cost distribution.

    Science.gov (United States)

    2010-04-01

    ... to 10 percent of the 50 percent matching amount), such as the current market value of donated common or office space, utility costs, furniture, material, supplies, equipment and food used in direct...

  3. 16 CFR 700.1 - Products covered.

    Science.gov (United States)

    2010-01-01

    ... the purchase transaction. An analysis of the transaction will determine whether the goods are real or..., but which have been packaged in a manner that does not permit breaking the package to purchase an item... sale at $12 must be designated, even though identical items may be offered in smaller quantities at...

  4. 25 CFR 700.725 - Livestock trespass.

    Science.gov (United States)

    2010-04-01

    ... according to the range unit Range Management Plan. (c) The grazing of livestock upon any land withdrawn from... approved by the Commissioner. (e) Grazing of livestock whose brand is not recorded in the range unit Range Management Plan. The owner of any livestock grazing in trespass on the New Lands is liable to a civil penalty...

  5. 40 CFR 700.45 - Fee payments.

    Science.gov (United States)

    2010-07-01

    ... shall be in United States currency and shall be paid by money order, bank draft, wire transfer, Pay.gov... Finance Center, Toxic Substances Control Act User Fees, P.O. Box 979073, St. Louis, MO 63197-9000. (3...

  6. 32 CFR 700.311 - Sole responsibilities.

    Science.gov (United States)

    2010-07-01

    ...) Acquisition; (2) Auditing; (3) Comptroller (including financial management); (4) Information management; (5... Executive and Senior Department of the Navy Information Resource Management Official. Responsibilities..., production, shipbuilding and production/logistics support programs; and Department of the Navy international...

  7. 25 CFR 700.465 - Technical feasibility.

    Science.gov (United States)

    2010-04-01

    ... construction, technology, or another engineering project, however, an application for a construction, technology or another engineering project shall: (a) Include sufficient information to determine the nature... management plan for the facility which identifies probable sources of operating funds. (e) An applicant who...

  8. 25 CFR 700.561 - Sexual harassment.

    Science.gov (United States)

    2010-04-01

    ... promotion, training, salary increases, rewards, etc., are based on an employee's submission to or rejection... productivity is also engaging in sexual harassment. (d) It is the policy of the Relocation Commission that...

  9. Dicty_cDB: Contig-U16209-1 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available 0 1 ( FJ393112 ) Uncultured Enterobacteriaceae bacterium clone MFC... 700 0.0 1 ( FJ268925 ) Uncultured Kleb...tia... 700 0.0 1 ( DQ852624 ) Klebsiella pneumoniae strain TM100 16S ribosomal ... 700 0.0 1 ( DQ837043 ) Enterobacteriaceae... bacterium p4s-5f 16S ribosomal... 700 0.0 1 ( DQ837041 ) Enterobacteriaceae bacterium p4f-5... 16S ribosomal ... 700 0.0 1 ( DQ520801 ) Enterobacteriaceae bacterium NR58 16S r... DQ379506 ) Klebsiella pneumoniae strain TSL-2 16S ribosomal ... 700 0.0 1 ( DQ313412 ) Enterobacteriaceae b

  10. 76 FR 69159 - Airworthiness Directives; The Boeing Company Airplanes Model 737-600, -700, -700C, -800, -900...

    Science.gov (United States)

    2011-11-08

    ... Velcro tabs and installing two fabric tunnels. Additionally, this service information describes... substantial direct effect on the States, on the relationship between the national Government and the States...

  11. Structural study of Sr0.3Ba0.7Nb2O6 and La0.030Sr0.255Ba0.700Nb2O6 ceramic systems

    International Nuclear Information System (INIS)

    Luna-Lopez, J.A.; Portelles, J.; Raymond, O.; Siqueiros, J.M.

    2009-01-01

    Sr 0.3 Ba 0.7 Nb 2 O 6 (SBN) and La 0.030 Sr 0.255 Ba 0.700 Nb 2 O 6 (LSBN) ceramic compounds have been prepared using the traditional ceramic method at two different calcination temperatures (900 and 1000 deg. C) and later sintered both at 1400 deg. C. A study of the effects of the calcination temperatures and La substitution on the morphological, compositional, and structural properties of SBN and LSBN is presented using scanning electronic microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD) analysis. From Rietveld refinement processes, the XRD patterns were interpreted to evaluate such effects in the structural parameters and the site occupation factors of the heavy metals and oxygen atoms. The effect of the incorporation of La resulted in a 0.25% cell contraction and turned out to be higher than the 0.08% dilation effect produced by the increase of calcination temperature. The La ion with similar effective ionic radius and higher electronegativity is incorporated into the structure occupying the A 1 site just like the Sr ions in the SBN compound. Differences in the site occupation factors between the SBN and LSBN samples lead to substantial changes in the physical properties such as temperature of relative dielectric constant maximum, relative dielectric constant, and dielectric loss, correlated with the distortion and the relative orientation of the oxygen octahedra.

  12. Use of the Diabetes Prevention Trial-Type 1 Risk Score (DPTRS) for improving the accuracy of the risk classification of type 1 diabetes.

    Science.gov (United States)

    Sosenko, Jay M; Skyler, Jay S; Mahon, Jeffrey; Krischer, Jeffrey P; Greenbaum, Carla J; Rafkin, Lisa E; Beam, Craig A; Boulware, David C; Matheson, Della; Cuthbertson, David; Herold, Kevan C; Eisenbarth, George; Palmer, Jerry P

    2014-04-01

    OBJECTIVE We studied the utility of the Diabetes Prevention Trial-Type 1 Risk Score (DPTRS) for improving the accuracy of type 1 diabetes (T1D) risk classification in TrialNet Natural History Study (TNNHS) participants. RESEARCH DESIGN AND METHODS The cumulative incidence of T1D was compared between normoglycemic individuals with DPTRS values >7.00 and dysglycemic individuals in the TNNHS (n = 991). It was also compared between individuals with DPTRS values 7.00 among those with dysglycemia and those with multiple autoantibodies in the TNNHS. DPTRS values >7.00 were compared with dysglycemia for characterizing risk in Diabetes Prevention Trial-Type 1 (DPT-1) (n = 670) and TNNHS participants. The reliability of DPTRS values >7.00 was compared with dysglycemia in the TNNHS. RESULTS The cumulative incidence of T1D for normoglycemic TNNHS participants with DPTRS values >7.00 was comparable to those with dysglycemia. Among those with dysglycemia, the cumulative incidence was much higher (P 7.00 than for those with values 7.00). Dysglycemic individuals in DPT-1 were at much higher risk for T1D than those with dysglycemia in the TNNHS (P 7.00. The proportion in the TNNHS reverting from dysglycemia to normoglycemia at the next visit was higher than the proportion reverting from DPTRS values >7.00 to values <7.00 (36 vs. 23%). CONCLUSIONS DPTRS thresholds can improve T1D risk classification accuracy by identifying high-risk normoglycemic and low-risk dysglycemic individuals. The 7.00 DPTRS threshold characterizes risk more consistently between populations and has greater reliability than dysglycemia.

  13. Insoluble Coatings for Stirling Engine Heat Pipe Condenser Surfaces

    Science.gov (United States)

    Dussinger, Peter M.; Lindemuth, James E.

    1997-01-01

    The principal objective of this Phase 2 SBIR program was to develop and demonstrate a practically insoluble coating for nickel-based superalloys for Stirling engine heat pipe applications. Specific technical objectives of the program were: (1) Determine the solubility corrosion rates for Nickel 200, Inconel 718, and Udimet 72OLI in a simulated Stirling engine heat pipe environment, (2) Develop coating processes and techniques for capillary groove and screen wick structures, (3) Evaluate the durability and solubility corrosion rates for capillary groove and screen wick structures coated with an insoluble coating in cylindrical heat pipes operating under Stirling engine conditions, and (4) Design and fabricate a coated full-scale, partial segment of the current Stirling engine heat pipe for the Stirling Space Power Convertor program. The work effort successfully demonstrated a two-step nickel aluminide coating process for groove wick structures and interior wall surfaces in contact with liquid metals; demonstrated a one-step nickel aluminide coating process for nickel screen wick structures; and developed and demonstrated a two-step aluminum-to-nickel aluminide coating process for nickel screen wick structures. In addition, the full-scale, partial segment was fabricated and the interior surfaces and wick structures were coated. The heat pipe was charged with sodium, processed, and scheduled to be life tested for up to ten years as a Phase 3 effort.

  14. Assessment of surface hardening effects from shot peening on a Ni-based alloy using electron backscatter diffraction techniques

    International Nuclear Information System (INIS)

    Child, D.J.; West, G.D.; Thomson, R.C.

    2011-01-01

    An electron backscatter diffraction (EBSD)-based tool is described to assess the depth of strain-hardening effects of shot-peening treatments applied to the Ni-based superalloy, Udimet (copy right) alloy 720Li. The method consists of a statistical analysis of a number of data points from each grain scanned based on the grain orientation spread and their relative position from the shot-peened edge. The output is a quantitative measure of the depth of strain-hardening effects. The tool is used at various shot-peening intensities to demonstrate the ability to distinguish between these changes, using a range of intensities from 4 to 10 Almen. An increase in shot-peening intensity is observed to increase the depth of strain-hardening effects in the alloy. A comparison with residual stress measurements using X-ray diffraction for the same material shows that the strain-hardened depth determined by EBSD extends to approximately half the distance of the residual stress present due to shot peening. A comparison is also made with predicted profiles from the Peenstress SM model and subsequent microhardness testing. A positive correlation is observed between strained hardened depth and surface roughness of the peened samples. In each case, the increases in surface roughness and strain-hardened depth diminish toward the upper end of the shot-peening intensity range studied for this alloy.

  15. Deformation mechanisms in a fine-grained Udimet 720LI nickel-base superalloy with high volume fractions of γ′ phases

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Jiayu, E-mail: chenjiayu975@126.com; Dong, Jianxin; Zhang, Maicang; Yao, Zhihao

    2016-09-15

    Hot-deformation behaviors and mechanisms below γ′ solvus of U720LI with fine-grained microstructure and high volume fractions of γ′ phases were studied. MTS hot-compressed samples under hot-deformation parameters (Temperatures of 1040 °C, 1070 °C, 1100 °C, 1130 °C, strain rates of 0.01 s{sup −1}, 0.1 s{sup −1}, 0.5 s{sup −1} and strains of 0.11, 0.36, 0.69 and 1.2) were investigated by using multiple microstructural analysis methods, such as transmission electron microscopy (TEM), electron channeling contrast image (ECCI), et al.. Rare recovery and recrystallization were observed indicating that other deformation mechanisms might be enhanced during the deformation process. Except for the pinning effect, deformation happened within γ′ phases and also γ′ phase promoted the deformation of the matrix. When the slipping was inhibited by γ′ phases, twinning acted as a deformation mechanism in fine-grained U720LI. Due to the retardation effect of γ′ phases in the early stage of the deformation process, local grain boundary migration took effect. Once grain boundaries crossed γ′ phases, it made recrystallization by strain induced boundary motion(SIBM) easier.

  16. Evaluación higrotérmica y energética de un edificio escolar perteneciente al programa nacional 700 escuelas, en el área Metropolitana de San Juan, Argentina.

    Directory of Open Access Journals (Sweden)

    María Guillermina Re

    2016-12-01

    Full Text Available El objetivo de este trabajo es evaluar el comportamiento higrotérmico y energético anual de un edificio escolar perteneciente al Programa Nacional 700 Escuelas, en el Área Metropolitana de San Juan, Argentina. Para ello, se efectúa el cálculo estacionario aplicando las Normas IRAM y se procesan los monitoreos realizados en tres momentos claves de los años 2013 y 2014, con el edificio en condiciones reales de ocupación, los cuales se relacionan con lecturas diarias de consumo energético. Adicionalmente, se estudian los niveles de confort en tres aulas mediante el método Fanger, determinando con un software específico los índices PMV y PPD. Por último, se computan los consumos históricos eléctricos y de gas, y se calculan los valores por unidad de superficie, que se comparan con antecedentes nacionales y estándares internacionales. El análisis llevado a cabo, a partir de la consideración de datos teóricos y empíricos, permite concluir que con un consumo anual promedio de 88 kWh/m2 el edificio cumple estándares internacionales de eficiencia energética escolar, sin embargo, su desempeño térmico es deficiente en las estaciones frías y cálidas, con ambientes que escapan de la zona de confort gran parte del tiempo. 

  17. How Much Learning Could Possibly Be Going On In A 700 Person General Education Science Course? Research Results On The Teaching And Learning Of A "Mega” Astro 101 Course

    Science.gov (United States)

    Prather, Edward E.; Rudolph, A. L.; Brissenden, G.; Cormier, S.; Consiglio, D.; Collaboration of Astronomy Teaching Scholars CATS

    2012-01-01

    Researchers with the NSF-funded Collaboration of Astronomy Teaching Scholars (CATS) Program and the JPL NASA funded Center for Astronomy Education at the University of Arizona have engaged in a multi-year study on the learning that occurs in a general education introductory astronomy class with an enrollment of greater than 700 students. This new "Mega” course, was modeled after the University of Arizona's highly-effective Astro 101 instructional environment which evolved out of the development and testing from the Lecture-Tutorials and Ranking-Task curriculum projects (Prather, Rudolph, & Brissenden 2009). We have undertaken an ambitious research project to assess the effectiveness of this Mega course through the simultaneous implementation of the Light and Spectroscopy Concept Inventory (LSCI), the Stellar Properties Concept Inventory (SPCI), The Lawson Test for Scientific Reasoning, and the Thinking about Science Survey Instrument (TSSI). Results indicate that the content learning gains of the students in these courses are quite high, and that new models for instruction pioneered for this course are critical to crating a productive and collaborative learning environment in the Mega classroom. This material is based in part upon work supported by the National Science Foundation under Grant No. 0715517, a CCLI Phase III Grant for the Collaboration of Astronomy Teaching Scholars (CATS). Any opinions, findings, and conclusions or recommendations expressed in this material are those of the authors and do not necessarily reflect the views of the National Science Foundation. Prather, E. E., A. L. Rudolph, and G. Brissenden. 2009. "Teaching and Learning Astronomy in the 21st Century.” Physics Today 62(10), 41.

  18. 75 FR 1529 - Airworthiness Directives; The Boeing Company Model 737-600, -700, -700C, -800, and -900 Series...

    Science.gov (United States)

    2010-01-12

    ... the potential for ignition sources inside fuel tanks caused by latent failures, alterations, repairs... repair if necessary. That AD resulted from a design review of the fuel tank systems. The actions... limitations for fuel tank systems to satisfy Special Federal Aviation Regulation No. 88 requirements. That AD...

  19. 76 FR 60710 - Airworthiness Directives; The Boeing Company Model 737-600, -700, -700C, -800, and -900 Series...

    Science.gov (United States)

    2011-09-30

    ... universal fault interrupters (UFIs) using a certain supplemental type certificate. This new AD continues to... interrupter (GFI) feature, or installation and maintenance of universal fault interrupters (UFIs) using a... section of this AD to include this contact information. Request To Revise a Word Boeing requested a change...

  20. 75 FR 50859 - Airworthiness Directives; The Boeing Company Model 737-600, -700, -700C, -800, and -900 Series...

    Science.gov (United States)

    2010-08-18

    ... prevent pump housing burn-through due to electrical arcing, which could create a potential ignition source... that the wire routing mitigates arcing. AirTran also states that in order for an ignition source to... circuit to burn through the motor-impeller assembly and through the housing. AirTran asserts that an arc...

  1. 76 FR 12634 - Airworthiness Directives; The Boeing Company Model 737-600, -700, -700C, -800, and -900 Series...

    Science.gov (United States)

    2011-03-08

    .... That AD states that the optional installation terminates the automatic shutoff system wiring test... installation of that protection system does not correct potential incorrect wiring that could exist on... NPRM proposed to require installation of an automatic shutoff system for the center tank fuel boost...

  2. 75 FR 81412 - Airworthiness Directives; The Boeing Company Model 737-600, -700, -700C, -800, and -900 Series...

    Science.gov (United States)

    2010-12-28

    ... condition that mechanics and technicians do not have the knowledge, training, and awareness to recognize... decals were implemented before July 1, 2007, and provide an acceptable level of safety. We have not...' mechanics because they would use the SRM only for repair to damages that are discovered or that occurred...

  3. Effects of pyrolysis temperature on soybean stover- and peanut shell-derived biochar properties and TCE adsorption in water.

    Science.gov (United States)

    Ahmad, Mahtab; Lee, Sang Soo; Dou, Xiaomin; Mohan, Dinesh; Sung, Jwa-Kyung; Yang, Jae E; Ok, Yong Sik

    2012-08-01

    Conversion of crop residues into biochars (BCs) via pyrolysis is beneficial to environment compared to their direct combustion in agricultural field. Biochars developed from soybean stover at 300 and 700 °C (S-BC300 and S-BC700, respectively) and peanut shells at 300 and 700 °C (P-BC300 and P-BC700, respectively) were used for the removal of trichloroethylene (TCE) from water. Batch adsorption experiments showed that the TCE adsorption was strongly dependent on the BCs properties. Linear relationships were obtained between sorption parameters (K(M) and S(M)) and molar elemental ratios as well as surface area of the BCs. The high adsorption capacity of BCs produced at 700 °C was attributed to their high aromaticity and low polarity. The efficacy of S-BC700 and P-BC700 for removing TCE from water was comparable to that of activated carbon (AC). Pyrolysis temperature influencing the BC properties was a critical factor to assess the removal efficiency of TCE from water. Copyright © 2012 Elsevier Ltd. All rights reserved.

  4. 78 FR 14274 - Privacy Act of 1974; System of Records

    Science.gov (United States)

    2013-03-05

    .../privacy/SORNs/govt/Gov_Wide_Notices.html . K700.13 602-26, Retention Register Files (February 22, 1993, 58... systems of records notices K700.13 602-26, Retention Register Files (February 22, 1993, 58 FR 10562); K700...

  5. Decadal variation of ocean heat content and tropical cyclone activity ...

    Indian Academy of Sciences (India)

    The upper ocean heat content up to 700 m depth (OHC700) is an important ... made to examine the inter-decadal variations of tropical cyclone (TC) activity and OHC700 over the ..... In: Climate change 2007: The physical science basis (eds).

  6. 25 CFR 700.333 - Determination of disability.

    Science.gov (United States)

    2010-04-01

    ... Indians THE OFFICE OF NAVAJO AND HOPI INDIAN RELOCATION COMMISSION OPERATIONS AND RELOCATION PROCEDURES... engage in any substantial gainful activity by reason of any medically determined physical or mental... continuous period of not less than twelve months. A physical or mental impairment is an impairment that...

  7. 16 CFR 700.6 - Designation of warranties.

    Science.gov (United States)

    2010-01-01

    ... the duration of an implied or written warranty (or service contract) applicable to the product... duration. However, where the duration of a full warranty is defined solely in terms of first purchaser...

  8. 30 CFR 905.700 - California Federal Program.

    Science.gov (United States)

    2010-07-01

    ... Hazardous Waste Control Law, Cal. Health & Safety Code section 25100 et seq. (West 1984). (4) The State Underground Storage of Hazardous Substances Law, Cal. Health & Safety Code section 25280 et seq. (West 1984... the Office of Management and Budget under 44 U.S.C. 3507 in its approval of the information collection...

  9. Search Results | Page 700 | IDRC - International Development ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Results 6991 - 7000 of 9602 ... ... in Natural Resource Industries (Argentina, Brazil and Chile) ... Governance and Management of Common Pool Resources in Viet Nam ... Landfill : Exploring Options to Protect Health, the Environment, and ...

  10. Machine Protection with a 700 MJ Beam

    Science.gov (United States)

    Baer, T.; Schmidt, R.; Wenninger, J.; Wollmann, D.; Zerlauth, M.

    After the high luminosity upgrade of the LHC, the stored energy per proton beam will increase by a factor of two as compared to the nominal LHC. Therefore, many damage studies need to be revisited to ensure a safe machine operation with the new beam parameters. Furthermore, new accelerator equipment like crab cavities might cause new failure modes, which are not sufficiently covered by the current machine protection system of the LHC. These failure modes have to be carefully studied and mitigated by new protection systems. Finally the ambitious goals for integrated luminosity delivered to the experiments during the era of HL-LHC require an increase of the machine availability without jeopardizing equipment protection.

  11. 700 kg jern med de smukkeste krystaller

    DEFF Research Database (Denmark)

    Pedersen, Jens Olaf Pepke

    2017-01-01

    Anmeldelse af Holger Pedersen, “Pallas Iron – Russia’s first meteorite”, 260 sider, 190 kr. BoD 2017 (www.bod.dk/bog/).......Anmeldelse af Holger Pedersen, “Pallas Iron – Russia’s first meteorite”, 260 sider, 190 kr. BoD 2017 (www.bod.dk/bog/)....

  12. 15 CFR 700.80 - Adjustments or exceptions.

    Science.gov (United States)

    2010-01-01

    ...) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE NATIONAL SECURITY INDUSTRIAL BASE REGULATIONS... exceptions. (a) A person may submit a request to the Office of Strategic Industries and Economic Security, U... interim relief is granted in writing by the Office of Strategic Industries and Economic Security. (d) A...

  13. 34 CFR 682.700 - Purpose and scope.

    Science.gov (United States)

    2010-07-01

    ... organization fails to meet the definition of “eligible lender” in section 435(d)(1) of the Act or the definition of “lender” in § 682.200, for any reason other than a violation of the prohibitions in section 435... of 1972 (relating to sex discrimination), which is governed by 34 CFR part 106. (c) This subpart does...

  14. 15 CFR 700.71 - Audits and investigations.

    Science.gov (United States)

    2010-01-01

    ... an individual may be made by serving a partner, corporate officer, or a managing or general agent... which service was made and the identity of the person served, and return the affidavit, and in the case...

  15. 25 CFR 700.815 - Issuance of permits.

    Science.gov (United States)

    2010-04-01

    ... competence in archaeological theory and methods, and in collecting, handling, analyzing, evaluating, and..., laboratory, or library research, administration, or management, including at least 4 months experience and/or..., scientific or scholarly research, and preservation of archaeological data; (3) The proposed work, including...

  16. 14 CFR 1206.700 - Schedule of fees.

    Science.gov (United States)

    2010-01-01

    ... photographs, blueprints, videotapes, engineering drawings, hard copies of aperture cards, etc., the fee...) Records will be provided in a form or format specified by the requester if they are readily reproducible in such format with reasonable efforts. If the records are not readily reproducible in the requested...

  17. 7 CFR 900.700 - Exemption from assessments.

    Science.gov (United States)

    2010-01-01

    ... defined by the Organic Foods Production Act of 1990 (OFPA) (7 U.S.C. 6502) and the NOP; certification that... consumption of the applicable commodity. (b) Any handler who operates under an approved National Organic Program (7 CFR part 205)(NOP) process system plan, only handles or markets organic products that are...

  18. 16 CFR 700.10 - Section 102(c).

    Science.gov (United States)

    2010-01-01

    ... consumer's use of an article or service identified by brand, trade, or corporate name unless that article... which impedes or precludes the choice by the consumer of the person or business to perform necessary... law, avoid liability under a written warranty where a defect is unrelated to the use by a consumer of...

  19. Search Results | Page 700 | IDRC - International Development ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Results 6991 - 7000 of 9602 ... Innovation, Learning and Institutional Frameworks in Natural Resource ... This project is concerned with how Latin American countries can take ... Community Based Adaptation to Climate Change in Africa.

  20. 25 CFR 700.113 - Basic acquisition policies.

    Science.gov (United States)

    2010-04-01

    ... believes is fair market value for improvements. This amount shall be based on a current appraisal at the...) Objection to determination of fair market value. If the owner objects to the Commission's determination of fair market value, the owner may request a hearing pursuant to the Commission's Hearing and...

  1. 25 CFR 700.267 - Disclosure of records.

    Science.gov (United States)

    2010-04-01

    ... form that is not individually identifiable; (4) To the National Archives of the United States as a... the record has such value; (5) To another agency or to an instrumentality of any governmental... if the activity is authorized by law, and if the head of the agency or instrumentality has made a...

  2. 24 CFR 700.175 - Other Federal requirements.

    Science.gov (United States)

    2010-04-01

    ... requirements described in 24 CFR part 44 (OMB Circular A-128). (b) Conflict of interest. In addition to the conflict of interest requirements in OMB Circular A-87 and 24 CFR part 85, no person who is an employee..., and the implementing regulations at 24 CFR part 108; and (3) Racial and ethnic collection requirements...

  3. Pramana – Journal of Physics | Indian Academy of Sciences

    Indian Academy of Sciences (India)

    Nuclear and Particle Physics Research Centre, Department of Physics, Jadavpur University, Kolkata 700 032, India; S.A. Jaipuria College, Kolkata 700 005, India; RCC Institute of Information Technology, Canal South Road, Beliaghata, Kolkata 700 015, India; Kanchrapara College, Kanchrapara, North 24 Parganas, West ...

  4. 75 FR 52242 - Airworthiness Directives; The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER...

    Science.gov (United States)

    2010-08-25

    ... attach lugs of the left and right elevator tab control mechanisms for discrepancies, and replacement of... results from reports of gaps in elevator tab control mechanisms and analysis that additional elevator tab... Engineer, Systems and Equipment Branch, ANM-130S, FAA, Seattle ACO, 1601 Lind Avenue, SW., Renton...

  5. 76 FR 61561 - Airworthiness Directives; The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER...

    Science.gov (United States)

    2011-10-05

    ... AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Final rule. SUMMARY: We are adopting a new... high work load and consequently reducing control of the airplane. Restricted movement of the rudder.... Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New...

  6. 76 FR 57625 - Special Conditions: Boeing Model 737-600, -700, -700C, -800, -900, and -900ER Series Airplanes...

    Science.gov (United States)

    2011-09-16

    ... addition, the substance of these special conditions has been subject to the public-comment process in...-battery cells use flammable liquid electrolytes. The electrolyte can serve as a source of fuel for an.... 25.1353 that are applicable to lithium batteries. The flammable-fluid fire-protection requirements of...

  7. Experimental investigation of iodine removal and containment depressurization in containment spray system test facility of 700 MWe Indian pressurized heavy water reactors

    Energy Technology Data Exchange (ETDEWEB)

    Jain, Manish [Department of Mechanical Engineering, I.I.T., Bombay, Powai, Mumbai (India); Kandar, T.K.; Vhora, S.F.; Mohan, Nalini [Directorate of Technology Development, Nuclear Power Corporation of India Limited, Mumbai (India); Iyer, K.N. [Department of Mechanical Engineering, I.I.T., Bombay, Powai, Mumbai (India); Prabhu, S.V., E-mail: svprabhu@iitb.ac.in [Department of Mechanical Engineering, I.I.T., Bombay, Powai, Mumbai (India)

    2017-05-15

    Highlights: • Depressurization rate in a scaled down vessel filled with air and steam is studied. • Iodine removal rate in a scaled down vessel filled with steam/air is investigated. • Effect of SMD and vessel pressure on depressurization rate is studied. • Depressurization rate decreases with the increase in the droplet size (590 μm – 1 mm) • Decrease in pressure and iodine concentration with time follow exponential trend. - Abstract: As an additional safety measure in the new 700 MWe Indian pressurized heavy water reactors, the first of a kind system called containment Spray System is introduced. The system is designed to cater/mitigate the conditions after design basis accidents i.e., loss of coolant accident and main steam line break. As a contribution to the safety analysis of condition following loss-of-coolant accidents, experiments are carried out to establish the performance of the system. The loss of coolant is simulated by injecting saturated steam and iodine vapors into the containment vessel in which air is enclosed at atmospheric and room temperature, and then the steam-air mixture is cooled by sprays of water. The effect of water spray on the containment vessel pressure and the iodine scrubbing in a scaled down facility is investigated for the containment spray system of Indian pressurized heavy water reactors. The experiments are carried out in the scaled down vessel of the diameter of 2.0 m and height of 3.5 m respectively. Experiments are conducted with water at room temperature as the spray medium. Two different initial vessel pressure i.e. 0.7 bar and 1.0 bar are chosen for the studies as they are nearing the loss of coolant accident & main steam line break pressures in Indian pressurized heavy water reactors. These pressures are chosen based on the containment resultant pressures after a design basis accident. The transient temperature and pressure distribution of the steam in the vessel are measured during the depressurization

  8. 78 FR 42526 - Salmonella

    Science.gov (United States)

    2013-07-16

    ...] Salmonella Contamination of Dry Dog Food; Withdrawal of Compliance Policy Guide AGENCY: Food and Drug... the withdrawal of the compliance policy guide (CPG) entitled ``Sec. 690.700 Salmonella Contamination... entitled ``Sec. 690.700 Salmonella Contamination of Dry Dog Food (CPG 690.700)'' on October 1, 1980. CPG...

  9. 47 CFR 90.421 - Operation of mobile station units not under the control of the licensee.

    Science.gov (United States)

    2010-10-01

    ... medical services activities. (3) On the Interoperability Channels in the 700 MHz Public Safety Band (See... in the 700 MHz Public Safety Band or by any licensee holding a license for any other public safety... hand-held and vehicular transmitters in the 700 MHz Band. (b) Industrial/Business Pool. Mobile units...

  10. Microtwin formation in the α phase of duplex titanium alloys affected by strain rate

    International Nuclear Information System (INIS)

    Lin, Yi-Hsiang; Wu, Shu-Ming; Kao, Fang-Hsin; Wang, Shing-Hoa; Yang, Jer-Ren; Yang, Chia-Chih; Chiou, Chuan-Sheng

    2011-01-01

    Research highlights: → The long and dense twins in α phase of SP700 alloy occurring at lower strain rates promote a good ductility. → The deformation in SP700 alloy changed to micro twins-controlled mechanism in α as the strain rate decreases. → The material has time to redistribute the deformed strain between α and β as the strain rate decreases. - Abstract: The effect of tensile strain rate on deformation microstructure was investigated in Ti-6-4 (Ti-6Al-4V) and SP700 (Ti-4.5Al-3V-2Mo-2Fe) of the duplex titanium alloys. Below a strain rate of 10 -2 s -1 , Ti-6-4 alloy had a higher ultimate tensile strength than SP700 alloy. However, the yield strength of SP700 was consistently greater than Ti-6-4 at different strain rates. The ductility of SP700 alloy associated with twin formation (especially at the slow strain rate of 10 -4 s -1 ), always exceeded that of Ti-6-4 alloy at different strain rates. It is caused by a large quantity of deformation twins took place in the α phase of SP700 due to the lower stacking fault energy by the β stabilizer of molybdenum alloying. In addition, the local deformation more was imposed on the α grains from the surrounding β-rich grains by redistributing strain as the strain rate decreased in SP700 duplex alloy.

  11. 78 FR 17080 - Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG Turbofan Engines

    Science.gov (United States)

    2013-03-20

    ... Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG Turbofan Engines AGENCY: Federal Aviation... certain Rolls-Royce Deutschland Ltd & Co KG (RRD) BR700-710 series turbofan engines. This AD requires... applies to Rolls-Royce Deutschland Ltd & Co KG (RRD) BR700-710A1-10 and BR700-710A2-20 turbofan engines...

  12. 75 FR 18399 - Special Conditions: Modification to Boeing Model 737-600/-700/-700C/-800/-900 and -900ER Series...

    Science.gov (United States)

    2010-04-12

    ..., transport-category airplanes. Large, high- capacity, rechargeable lithium batteries and rechargeable lithium... requirements, are established to ensure the availability of electrical power from the batteries when needed... external fire from a breach of the battery container. Such problems, experienced by users of rechargeable...

  13. 76 FR 66198 - Airworthiness Directives; Bombardier, Inc. Model BD-700-1A10 and BD-700-1A11 Airplanes

    Science.gov (United States)

    2011-10-26

    ...., Monday through Friday, except Federal holidays. For service information identified in this proposed AD...., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory... airplanes, certificated in any category, serial numbers (S/N) 9002 through 9126 inclusive, 9128 through 9312...

  14. 75 FR 68690 - Airworthiness Directives; Bombardier, Inc. Model BD-700-1A10 and BD-700-1A11 Airplanes

    Science.gov (United States)

    2010-11-09

    ... five reported cases of balance washer screw failure on similar RATs [ram air turbines]/air driven... turbine imbalance. Such imbalance could potentially result in RAT structural failure (including blade... activated by a dual engine shutdown, could also result in loss of hydraulic power for the flight controls...

  15. 75 FR 63420 - Airworthiness Directives; Bombardier, Inc. Model BD-700-1A10 and BD-700-1A11 Airplanes

    Science.gov (United States)

    2010-10-15

    ... reports of main landing gear (MLG) tire failure on landing, during which a flailing tire tread caused... the brake system performance could adversely affect the aircraft during landing. * * * * * [[Page... have been two in-service reports of main landing gear (MLG) tire failure on landing, during which a...

  16. Adsorptive Removal of Trichloroethylene in Water by Crop Residue Biochars Pyrolyzed at Contrasting Temperatures: Continuous Fixed-Bed Experiments

    Directory of Open Access Journals (Sweden)

    Ming Zhang

    2015-01-01

    Full Text Available Biochar (BC has attracted great attention as an alternative sorbent to activated carbon (AC. Objective of this study was to determine trichloroethylene (TCE removal by soybean stover BC pyrolyzed at 300 (BC300 and 700°C (BC700 in continuous fixed-bed column. Columns packed with BC300, BC700, and AC reached breakthrough time in 1.1, 27.0, and 50.7 h, respectively. BC700 had higher TCE adsorption capacity than BC300 due to its higher surface area, nonpolarity, and aromaticity. The sorption capacities of AC (774.0 mg g−1 and BC700 (515.1 mg g−1 were 21.6 and 14.4 times higher than that of BC300 (35.9 mg g−1. The lower desorption rate of TCE from BC300 than BC700 and AC may be attributed to the strong binding/partition of TCE to the noncarbonized part of BC. Thomas model also adequately described the adsorption data indicating interphase mass transfer. Overall, AC showed best efficiency for removing TCE from water in column experiments. However, although sorption and desorption capabilities of BC700 were a little lower than AC, it is still a good alternative for AC to remove organic contaminants such as TCE from water due to its cost-effectiveness.

  17. 78 FR 77382 - Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG Turbofan Engines

    Science.gov (United States)

    2013-12-23

    ... Deutschland Ltd & Co KG Turbofan Engines AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of...-Royce Deutschland Ltd & Co KG (RRD) BR700-715A1-30, BR700-715B1- 30, and BR700-715C1-30 turbofan engines... turbofan engines installed on aircraft of U.S. registry. We also estimate that it would take about 24 hours...

  18. Efeitos de dose de nitrogênio, fósforo e potássio sobre os componentes da produção e a qualidade de bananas 'Prata Anã' no distrito agroindustrial de Jaíba Effects of nitrogen, phosphorous and potassium on components of production and quality of 'Prata Anã' banana in the Jaíba agro-industrial district

    Directory of Open Access Journals (Sweden)

    Victor Martins Maia

    2003-08-01

    Full Text Available Com o objetivo de verificar os efeitos da adubação nitrogenada, fosfatada e potássica sobre os componentes da produção e a qualidade de bananas 'Prata Anã', no Distrito Agroindustrial de Jaíba, em Matias Cardoso-MG, foi conduzido um experimento com dez tratamentos constituídos pela combinação de doses (g/touceira de N, P e K de acordo com uma matriz baconiana, sendo 1: 250-45-700, 2: 250-25-700, 3: 250-70-700, 4: 250-100-700, 5: 250-45-300, 6: 250-45-500, 7: 250-45-1000, 8: 150-45-700, 9: 400-45-700, 10: 600-45-700. O tratamento um é o de referência, correspondendo às doses adotadas pelos bananicultores da região. O delineamento foi de blocos ao acaso com quatro repetições. Avaliou-se a produção do primeiro ciclo. Os cachos foram colhidos, despencados e avaliados quanto ao número de pencas, número de frutos e massa do cacho, massa média das pencas e massa média, diâmetro e comprimentos total e comercial do fruto. Os resultados indicaram que as doses de nitrogênio ou fósforo utilizadas pelos produtores de banana do Distrito Agroindustrial de Jaíba podem ser reduzidas para 150 ou 25 g/touceira, respectivamente, sem prejuízo para a produção e qualidade dos frutos. Por outro lado, as doses de potássio até 1000 g/touceira, parceladas semanalmente, proporcionaram aumentos significativos na massa, comprimento total e comercial do fruto.An experiment was carried out in the Jaíba Agro-industrial District, located in Matias Cardoso, Minas Gerais, to evaluate the effect of nitrogen, phosphate and potassium fertilization on 'Prata Anã' banana production and quality. The experiment consisted of ten treatments with compound fertilizers using a baconian matrix (1: 250-45-700, 2: 250-25-700, 3: 250-70-700, 4: 250-100-700, 5: 250-45-300, 6: 250-45-500, 7: 250-45-1000, 8: 150-45-700, 9: 400-45-700, 10: 600-45-700 g/shoot of N, P and K, respectively, in which the first treatment includes the reference doses used by the region

  19. Arsenic removal by perilla leaf biochar in aqueous solutions and groundwater: An integrated spectroscopic and microscopic examination.

    Science.gov (United States)

    Niazi, Nabeel Khan; Bibi, Irshad; Shahid, Muhammad; Ok, Yong Sik; Burton, Edward D; Wang, Hailong; Shaheen, Sabry M; Rinklebe, Jörg; Lüttge, Andreas

    2018-01-01

    In this study, we examined the removal of arsenite (As(III)) and arsenate (As(V)) by perilla leaf-derived biochars produced at 300 and 700 °C (referred as BC300 and BC700) in aqueous environments. Results revealed that the Langmuir isotherm model provided the best fit for As(III) and As(V) sorption, with the sorption affinity following the order: BC700-As(III) > BC700-As(V) > BC300-As(III) > BC300-As(V) (Q L  = 3.85-11.01 mg g -1 ). In general, As removal decreased (76-60%) with increasing pH from 7 to 10 except for the BC700-As(III) system, where notably higher As removal (88-90%) occurred at pH from 7 to 9. Surface functional moieties contributed to As sequestration by the biochars examined here. However, significantly higher surface area and aromaticity of BC700 favored a greater As removal compared to BC300, suggesting that surface complexation/precipitation dominated As removal by BC700. Arsenic K-edge X-ray absorption near edge structure (XANES) spectroscopy demonstrated that up to 64% of the added As(V) was reduced to As(III) in BC700- and BC300-As(V) sorption experiments, and in As(III) sorption experiments, partial oxidation of As(III) to As(V) occurred (37-39%). However, XANES spectroscopy was limited to precisely quantify As binding with sulfur species as As 2 S 3 -like phase. Both biochars efficiently removed As from natural As-contaminated groundwater (As: 23-190 μg L -1 ; n = 12) despite in the presence of co-occurring anions (e.g., CO 3 2- , PO 4 3- , SO 4 2- ) with the highest levels of As removal observed for BC700 (97-100%). Overall, this study highlights that perilla leaf biochars, notably BC700, possessed the greatest ability to remove As from solution and groundwater (drinking water). Significantly, the integrated spectroscopic techniques advanced our understanding to examine complex redox transformation of As(III)/As(V) with biochar, which are crucial to determine fate of As on biochar in aquatic environments. Copyright

  20. Augmented reality building operations tool

    Science.gov (United States)

    Brackney, Larry J.

    2014-09-09

    A method (700) for providing an augmented reality operations tool to a mobile client (642) positioned in a building (604). The method (700) includes, with a server (660), receiving (720) from the client (642) an augmented reality request for building system equipment (612) managed by an energy management system (EMS) (620). The method (700) includes transmitting (740) a data request for the equipment (612) to the EMS (620) and receiving (750) building management data (634) for the equipment (612). The method (700) includes generating (760) an overlay (656) with an object created based on the building management data (634), which may be sensor data, diagnostic procedures, or the like. The overlay (656) is configured for concurrent display on a display screen (652) of the client (642) with a real-time image of the building equipment (612). The method (700) includes transmitting (770) the overlay (656) to the client (642).

Some links on this page may take you to non-federal websites. Their policies may differ from this site.