WorldWideScience

Sample records for u-bearing mineral phases

  1. U-bearing particles in miners' and millers' lungs

    International Nuclear Information System (INIS)

    Paschoa, A.S.; Wrenn, M.E.; Singh, N.P.; Miller, S.C.; Jones, K.W.; Cholewa, M.; Hanson, A.L.; Saccomanno, G.

    1984-01-01

    The size distribution of uranium-bearing particles in air particulates in occupational areas of active uranium mines and mills is largely uninvestigated. Investigation of the size of residual uranium-bearing particles in uranium miners' and millers' lungs is warranted because significant inhalation of uranium can occur in certain occupational areas. Average uranium concentrations of about 0.3 ppM U in uranium miners' and millers' lungs have been reported. Local uranium concentrations in uranium-bearing particles inhaled and regionally deposited in the lungs of uranium miners and millers are orders of magnitude larger than the average uranium concentrations reported. The feasibility of using microPIXE (particle induced x-ray emission) techniques to search for such uranium-bearing particles embedded in lung tissues has been demonstrated. Proton microbeams 20 μm in diameter, scanning in 5 μm steps, were used to irradiate sections of lung tissues 10 to 40 μm thick. The paper will briefly describe the method, and present and discuss the results obtained in an extensive search for uranium-bearing particles embedded in lung tissues, collected at autopsy, of former uranium miners and millers. 13 references, 1 table

  2. Identification of Uranium Minerals in Natural U-Bearing Rocks Using Infrared Reflectance Spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Beiswenger, Toya N. [Pacific Northwest National Laboratory, Richland, WA, USA; Gallagher, Neal B. [Eigenvector Research, Inc., Manson, WA, USA; Myers, Tanya L. [Pacific Northwest National Laboratory, Richland, WA, USA; Szecsody, James E. [Pacific Northwest National Laboratory, Richland, WA, USA; Tonkyn, Russell G. [Pacific Northwest National Laboratory, Richland, WA, USA; Su, Yin-Fong [Pacific Northwest National Laboratory, Richland, WA, USA; Sweet, Lucas E. [Pacific Northwest National Laboratory, Richland, WA, USA; Lewallen, Tricia A. [Pacific Northwest National Laboratory, Richland, WA, USA; Johnson, Timothy J. [Pacific Northwest National Laboratory, Richland, WA, USA

    2017-10-24

    The identification of minerals, including uranium-bearing minerals, is traditionally a labor-intensive-process using x-ray diffraction (XRD), fluorescence, or other solid-phase and wet chemical techniques. While handheld XRD and fluorescence instruments can aid in field identification, handheld infrared reflectance spectrometers can also be used in industrial or field environments, with rapid, non-destructive identification possible via spectral analysis of the solid’s reflectance spectrum. We have recently developed standard laboratory measurement methods for the infrared (IR) reflectance of solids and have investigated using these techniques for the identification of uranium-bearing minerals, using XRD methods for ground-truth. Due to the rich colors of such species, including distinctive spectroscopic signatures in the infrared, identification is facile and specific, both for samples that are pure or are partially composed of uranium (e.g. boltwoodite, schoepite, tyuyamunite, carnotite, etc.) or non-uranium minerals. The method can be used to detect not only pure and partial minerals, but is quite sensitive to chemical change such as hydration (e.g. schoepite). We have further applied statistical methods, in particular classical least squares (CLS) and multivariate curve resolution (MCR) for discrimination of such uranium minerals and two uranium pure chemicals (U3O8 and UO2) against common background materials (e.g. silica sand, asphalt, calcite, K-feldspar) with good success. Each mineral contains unique infrared spectral features; some of the IR features are similar or common to entire classes of minerals, typically arising from similar chemical moieties or functional groups in the minerals: phosphates, sulfates, carbonates, etc. These characteristic 2 infrared bands generate the unique (or class-specific) bands that distinguish the mineral from the interferents or backgrounds. We have observed several cases where the chemical moieties that provide the

  3. Cationic flotation for separating U-bearing phosphorite mineral from uraniferous phosphatic sandstone deposit of Gebel Qatrani, Western desert of Egypt

    International Nuclear Information System (INIS)

    Abel Monem, H.M.

    1986-01-01

    Uraniferous phosphatic sandstone is one of the important radioactive oligocene deposits of Gebel Qatrani, Western desert of Egypt, which is assayed 72,36% SiO 2 , 9.85% P 2 O 5 and 0.091% of oU. Attrition scrubbing process was utilized to assist in the mild of libration of uraniferous phosphorite locked grains of the crushed oversize fraction (+48 mesh). Cationic flotation using AEROMINE 3037 of American Cynamide Company, diluted with kerosene in ratio 1,2 (wt/wt), and 2.5mg/50g pine oil as frothier were used for separating U-bearing phosphorite as hydrophilic mineral from the associated siliceous gangue minerals at pH 6.5. A proposed flowsheet was designed for production of a high grade uraniferous phosphorite concentrate assaying 32.01% P 2 O 5 , 0.39% eU and 5.65% SiO 2 with an overall recovery of 71.98%

  4. Advantages of conducting in-situ U-Pb age dating of multiple U-bearing minerals from a single complex: Case in point - the Oka Carbonatite Complex

    Science.gov (United States)

    Chen, W.; Simonetti, A.

    2012-12-01

    A detailed radiometric investigation is currently underway focusing on U-bearing accessory minerals apatite, perovskite, and niocalite from the Oka Carbonatite Complex (Canada). One of the main objectives is to obtain a comparative chronology of melt crystallization for the complex. Unlike other commonly adopted U-bearing minerals (e.g., zircon, monazite) for in-situ dating investigations, apatite, perovskite, and niocalite contain relatively high contents of common Pb. Hence, careful assessment of the proportion and composition of the common Pb, and usage of appropriate matrix-matched external standards are imperative. The Madagascar apatite was utilized as the external standard for apatite dating, and the Emerald Lake and Durango apatites were adopted as secondary standards; the latter yield ages of 92.6 ±1.8 and 32.2 ±1.1 Ma, respectively, and these are identical to their accepted ages. Pb/U ages for apatite from Oka were obtained for different rock types, including 8 carbonatites, 4 okaites, 3 ijolites and 3 alnoites, and these define a range of ages between ~105 and ~135 Ma; this result suggests a protracted crystallization history. In total, 266 individual analyses define two peaks at ~115 and ~125Ma. For perovskite dating, the Ice River perovskite standard was utilized as the external standard. The perovskites from one okaite sample yield an age of 112.2 ±1.9 Ma, and is much younger than the previously reported U-Pb perovskite age of 131 ±7 Ma. Hence, the combined U-Pb perovskite ages also suggest a rather prolonged time of melt crystallization. Niocalite is a rare, accessory silicate mineral that occurs within the carbonatites at Oka. The international zircon standard BR266 was selected for use as the external standard and rastering was employed to minimize the Pb-U fractionation. Two niocalite samples give young ages at 110.6 ±1.2 and 115.0 ±1.9 Ma, and are identical to their respective apatite ages (given associated uncertainties) from the same

  5. Phanerozoic Rifting Phases And Mineral Deposits

    Science.gov (United States)

    Hassaan, Mahmoud

    2016-04-01

    connected with NW,WNW and N-S faults genetically related to volcano-hydrothermal activity associated the Red Sea rifting. At Sherm EL-Sheikh hydrothermal manganese deposit occurs in Oligocene clastics within fault zone. Four iron-manganese-barite mineralization in Esh-Elmellaha plateau are controlled by faults trending NW,NE and nearly E-W intersecting Miocene carbonate rocks. Barite exists disseminated in the ores and as a vein in NW fault. In Shalatee - Halaib district 24 manganese deposits and barite veins with sulphide patches occur within Miocene carbonates distributed along two NW fault planes,trending 240°and 310° and occur in granite and basalt . Uranium -lead-zinc sulfide mineralization occur in Late Proterozoic granite, Late Cretaceous sandstones, and chiefly in Miocene clastic-carbonate-evaporate rocks. The occurrences of uranium- lead-zinc and iron-manganese-barite mineralization have the characteristic features of hypogene cavity filling and replacement deposits correlated with Miocene- Recent Aden volcanic rocks rifting. In western Saudi Arabia barite-lead-zinc mineralization occurs at Lat. 25° 45' and 25° 50'N hosted by Tertiary sediments in limestone nearby basaltic flows and NE-SW fault system. The mineralized hot brines in the Red Sea deeps considered by the author a part of this province. The author considers the constant rifting phases of Pangea and then progressive fragmentation of Western Gondwana during the Late Carboniferous-Lias, Late Jurassic-Early Aptian, Late Aptian - Albian and Late Eocene-Early Miocene and Oligocene-Miocene, responsible for formation of the mineral deposits constituting the M provinces. During these events, rifting, magmatism and hydrothermal activities took place in different peri-continental margins.

  6. Analysis of mineral phases in coal utilizing factor analysis

    International Nuclear Information System (INIS)

    Roscoe, B.A.; Hopke, P.K.

    1982-01-01

    The mineral phase inclusions of coal are discussed. The contribution of these to a coal sample are determined utilizing several techniques. Neutron activation analysis in conjunction with coal washability studies have produced some information on the general trends of elemental variation in the mineral phases. These results have been enhanced by the use of various statistical techniques. The target transformation factor analysis is specifically discussed and shown to be able to produce elemental profiles of the mineral phases in coal. A data set consisting of physically fractionated coal samples was generated. These samples were analyzed by neutron activation analysis and then their elemental concentrations examined using TTFA. Information concerning the mineral phases in coal can thus be acquired from factor analysis even with limited data. Additional data may permit the resolution of additional mineral phases as well as refinement of theose already identified

  7. Mineral vein dynamics modeling (FRACS). Phase 1

    Energy Technology Data Exchange (ETDEWEB)

    Urai, J.; Virgo, S.; Arndt, M. [RWTH Aachen (Germany). Geologie-Endogene Dynamik] [and others

    2013-07-15

    The Mineral Vein Dynamics Modeling group ''FRACS'' is a team of 7 research groups from the Universities of Mainz, Aachen, Tuebingen, Karlsruhe, Bayreuth, ETH Zuerich and Glasgow working on an understanding of the dynamic development of fracturing, fluid flow and fracture sealing. World-class field laboratories, especially carbonate sequences from the Oman Mountains are studied and classified. State of the art numerical programs are written, expanded and used to simulate the dynamic interaction of fracturing, flow and resealing and the results are compared with the natural examples. Newest analytical technologies including laser scanning, high resolution X-ray microtomography, fluid inclusion and isotope analysis are performed to understand and compare the results of simulations with natural examples. A new statistical program was developed to classify the natural fracture and vein systems and compare them with dynamic numerical simulations and analytical models. The results of the first project phase are extremely promising. Most of the numerical models have been developed up to the stage where they can be used to simulate the natural examples. The models allow a definition of the first proxies for high fluid pressure and tectonic stresses. It was found out that the Oman Mountains are a complex and very dynamic system that constantly fractures and reseals from the scale of small veins up to the scale of large normal and strike slip faults. The numerical simulations also indicate that the permeability of such systems is not a constant but that the system adjusts to the driving force, for ex-ample high fluid pressure. When the system reseals fast a fluctuating behavior can be observed in the models where the system constantly fractures and reseals, which is in accordance with the observation of the natural laboratory.

  8. Heavy metal immobilization in mineral phases

    International Nuclear Information System (INIS)

    Apblett, A.

    1993-01-01

    A successful waste form for toxic or radioactive metals must not only have the ability to chemically incorporate the elements but it must also be extremely stable in the geological environment. Thus, ceramic wasteforms are sought which mimic those minerals that have sequestered the hazardous metals for billions of years. One method for producing ceramics, metal organic deposition (MOD) is outstanding in its simplicity, versatility, and inexpensiveness. The major contribution that the MOD process can make to ceramic waste forms is the ability to mix the toxic metals at a molecular level with the elements which form the ceramic matrix. With proper choice of organic ligands, the inclusion of significant amounts of alkali metals in the ceramic and, hence, their detrimental effect on durability may be avoided. In the first stage of our research we identified thermally-unstable ligands which could fulfill the role of complexing toxic metal species and allowing their precipitation or extraction into nonaqueous solvents

  9. COMPOSITION OF MINERAL PHASES OF THE GHIDIRIM DIATOMITE

    Directory of Open Access Journals (Sweden)

    Vasile Rusu

    2007-06-01

    Full Text Available Studies of the mineralogical composition of diatomite from the Ghidirim location of RM, as well as of the extracted clay phase are presented. The mineral phase of the diatomite contains a number of clay minerals, like montmorillonite (in a mixture with insignificant quantities of slightly chloritized montmorillonite, illite and kaolinite. Diatomite contains also non-clay components as fine-dispersed quartz and amorphous material, the more probable sources of which are opal, amorphous alumosilicates, aluminum and iron hydroxides. The applied procedure for separation of clay fractions by sizing settling in liquid media proves to be very useful, enabling possibilities for more accurate identification of the clay constituents of diatomic material. Procedure allows to separate very clean clay fraction especially rich in montmorillonite, which can be utilized itself as mineral adsorbent for practical purposes.

  10. Scattering Phase Functions of Constituents of Mineral Dust Aerosols ...

    African Journals Online (AJOL)

    ... Montmorillonte, Hematite, Calcite and Quartz. The behaviour of these constituents as observed by their phase functions provide information on the optical properties and radiative effects of the mineral dust types and is therefore useful on regional and global scales in assessing radiative impacts of dust outbreak events.

  11. Analysis of Mineral Assemblages Containing Unstable Hydrous Phases

    Science.gov (United States)

    Vaniman, D. T.; Wilson, S. A.; Bish, D. L.; Chipera, S.

    2011-12-01

    Minerals in many environments can be treated as durable phases that preserve a record of their formation. However many minerals, especially those with hydrogen-bonded H2O molecules as part of their structure, are ephemeral and are unlikely to survive disturbance let alone removal from their environment of formation. Minerals with exceptionally limited stability such as meridianiite (Mg-sulfate 11 hydrate), ikaite (Ca-carbonate 6 hydrate), and mirabilite (Na-sulfate 10 hydrate) are very susceptible to destabilization during analysis, and even modest changes in temperature or relative humidity can lead to change in hydration state or deliquescence. The result may be not only loss of the salt hydrate but dissolution of other salts present, precipitation of new phases, and ion exchange between the concentrated solution and otherwise unaffected phases. Exchange of H2O molecules can also occur in solid-vapor systems without any liquid involvement; moreover, recent work has shown that cation exchange between smectite and sulfate hydrates can occur without any liquid phase present other than a presumed thin film at the salt-silicate interface. Among hydrous silicates, clay minerals are susceptible to cation exchange and similar alteration can be expected for zeolites, palagonite, and possibly other hydrous silicate alteration products. Environmentally sensitive phases on Mars, such as meridianiite, may occur at higher latitudes or in the subsurface where permafrost may be present. Accurate determination of the presence and paragenesis of such minerals will be important for understanding the near-surface hydrogeology of Mars, and in situ analysis may be the only way to obtain this information. Access to the subsurface may be required, yet the act of exposure by excavation or drilling can itself lead to rapid degradation as the sample is exposed or brought to the surface for analysis. Mars is not the only body with which to be concerned, for similar concerns can be raised

  12. Heteroaggregation of graphene oxide with minerals in aqueous phase.

    Science.gov (United States)

    Zhao, Jian; Liu, Feifei; Wang, Zhenyu; Cao, Xuesong; Xing, Baoshan

    2015-03-03

    Upon release into waters, sediments, and soils, graphene oxide (GO) may interact with fine mineral particles. We investigated the heteroaggregation of GO with different minerals, including montmorillonite, kaolinite, and goethite, in aqueous phase. GO significantly enhanced the dispersion of positively charged goethite (>50%) via heteroaggregation, while there was no interaction between GO and negatively charged montmorillonite or kaolinite. Electrostatic attraction was the dominant force in the GO-goethite heteroaggregation (pH 4.0-8.5), and the dissolved Fe ions (formation of multilayered GO-goethite complex with high configurational stability. These findings are useful for understanding the interaction of GO with mineral surfaces, and potential fate and toxicity of GO under natural conditions in aquatic environments, as well as in soils and sediments.

  13. Mineral phases identification inside an abandoned Zn/Pb mine

    International Nuclear Information System (INIS)

    Goienaga, N.; Carrero, J.A.; Olivares, M.; Castro, K.; Fernandez, L.A.; Madariaga, J.M.

    2009-01-01

    Complete text of publication follows. The aim of the work is the identification of the sulphurated phase's outbreak on an aragonite, dolomite and calcite-based original rock inside an abandoned mine. The studied Blende/Galena (ZnS/PbS) Mine, located in Lanestosa (Bizkaia, North of Spain) was operative until 1950. After decades, the area has only supported wild life and thus nowadays it could be considered as a polluted site which has become naturalized. The main alteration factors inside the mine are percolated water, gases come from the outside (CO 2 , O 2 ) and biological activities. Mining activities generates loads of ore minerals and unwanted materials that with the time impact the surrounding environment. The waste includes granular, broken rock and soils ranging in size from the fine sand to large boulders, with the content of fine material largely dependent on the nature of the formation and extraction methods employed during mining. Waste materials geochemistry varies widely from mine to mine and may vary significantly at individual mines over time as different lithologic strata are exposed and geochemical processes alter characteristics of the waste. In order to determine the finest mineral composition in the galleries, several samples were collected. Once dried in a fume hood and sieved, the portions below 250 μm were subjected to non-destructive Raman spectroscopic analysis. The measurements reflected the ore precursors (primary phases: Blende, and Galena), several primary carbonates (dolomite, calcite and aragonite) with secondary minerals in trace levels (Brookite, Libethenite, Fluorapatita, Anatasa, Quartz, Apatite, Augite, Diopside, Anthracite, Hematite, Cosalite, Epidote, Rutile) and transformation products, probably of recent formation (Smithsonite, Massicot, Plattnerite, Gypsum, Siderite, Mendiphite, Escorodite, Gauberite, Goethite or Mascagnite). The origin of the secondary mineral may be related to percolated rain and snow water. This

  14. Hydrothermal Phase Relations Among Uranyl Minerals at the Nopal I Analog Site

    International Nuclear Information System (INIS)

    Murphy, William M.

    2007-01-01

    Uranyl mineral paragenesis at Nopal I is an analog of spent fuel alteration at Yucca Mountain. Petrographic studies suggest a variety of possible hydrothermal conditions for uranium mineralization at Nopal I. Calculated equilibrium phase relations among uranyl minerals show uranophane stability over a broad range of realistic conditions and indicate that uranyl mineral variety reflects persistent chemical potential heterogeneity. (author)

  15. Saturation of the hydroxyapatite mineral phase using radioactive fluorine

    International Nuclear Information System (INIS)

    Flores de la Torre, J.A.; Badillo A, V.E.; Lopez D, F.A.

    2005-01-01

    With the purpose of knowing the Anion exchange capacity (CIA) of the hydroxyapatite mineral phase, marketed by BIO-RAD, becomes necessary to saturate the surface of the mineral with an anion specie that possesses a strong affinity by this solid as it is the case of the fluorine. Moreover it takes advantage that offers the radioactive tracer technique, using the radioactive isotope of the fluorine, 18 F, produced in the cyclotron of the UNAM. This saturation is obtained in terms of the quantity of retained fluorine (mmol/ 100 g) in the synthetic hydroxyapatite in function of the concentration of the solution of NaF that oscillates from 0.7 M up to 0.16 M to fixed values of pH of 9.2. Those results demonstrate that to this fixed pH value the saturation of the surface of the hydroxyapatite is achieved in approximately 30 mmol/ 100 g, using important concentrations of NaF that correspond to 0.14 M from now on. This result demonstrates the high capacity of the solid considered to retain considerable quantities of fluorine even to basic pH values. (Author)

  16. Minerals

    Science.gov (United States)

    Minerals are important for your body to stay healthy. Your body uses minerals for many different jobs, including keeping your bones, muscles, heart, and brain working properly. Minerals are also important for making enzymes and hormones. ...

  17. Headspace analysis gas-phase infrared spectroscopy: a study of xanthate decomposition on mineral surfaces

    Science.gov (United States)

    Vreugdenhil, Andrew J.; Brienne, Stephane H. R.; Markwell, Ross D.; Butler, Ian S.; Finch, James A.

    1997-03-01

    The O-ethyldithiocarbonate (ethyl xanthate, CH 3CH 2OCS -2) anion is a widely used reagent in mineral processing for the separation of sulphide minerals by froth flotation. Ethyl xanthate interacts with mineral powders to produce a hydrophobic layer on the mineral surface. A novel infrared technique, headspace analysis gas-phase infrared spectroscopy (HAGIS) has been used to study the in situ thermal decomposition products of ethyl xanthate on mineral surfaces. These products include CS 2, COS, CO 2, CH 4, SO 2, and higher molecular weight alkyl-containing species. Decomposition pathways have been proposed with some information determined from 2H- and 13C-isotope labelling experiments.

  18. Minerals

    Science.gov (United States)

    ... Aren't minerals something you find in the earth, like iron and quartz? Well, yes, but small ... canned salmon and sardines with bones leafy green vegetables, such as broccoli calcium-fortified foods — from orange ...

  19. Minerals

    Directory of Open Access Journals (Sweden)

    Vaquero, M. P.

    1998-08-01

    Full Text Available The possible changes in the mineral composition of food during frying could be the consequence of losses by leaching, or changes in concentrations caused by exchanges between the food and culinary fat of other compounds. The net result depends on the type of food, the frying fat used and the frying process. Moreover, the modifications that frying produces in other nutrients could indirectly affect the availability of dietary minerals. The most outstanding ones are those that can take place in the fat or in the protein. With respect to the interactions between frying oils and minerals, we have recent knowledge concerning the effects of consuming vegetable oils used in repeated fryings of potatoes without turnover, on the nutritive utilization of dietary minerals. The experiments have been carried out in pregnant and growing rats, which consumed diets containing, as a sole source of fat, the testing frying oils or unused oils. It seems that the consumption of various frying oils, with a polar compound content lower or close to the maximum limit of 25% accepted for human consumption, does not alter the absorption and metabolism of calcium, phosphorous, iron or copper. Magnesium absorption from diets containing frying oils tends to increase but the urinary excretion of this element increases, resulting imperceptible the variations in the magnesium balance. The urinary excretion of Zn also increased although its balance remained unchanged. Different studies referring to the effects of consuming fried fatty fish on mineral bioavailability will also be presented. On one hand, frying can cause structural changes in fish protein, which are associated with an increase in iron absorption and a decrease in body zinc retention. The nutritive utilization of other elements such as magnesium, calcium and copper seems to be unaffected. On the other hand; it has been described that an excess of fish fatty acids in the diet produces iron depletion, but when fatty

  20. Phase transformations of pyrophyllite clay mineral after heat treatment

    International Nuclear Information System (INIS)

    Salvadori, M.C.

    1988-01-01

    The termal transformation of the Pyrophyllite clay mineral, given by the equations: AL sub(2) O sub(3).4SiO sub(2).H sub(2) O → Al sub(2) O sub(3).4SiO sub(2) + H sub(2) O Pyrophyllite Anhydride Water vapour. 3 (Al sub(2) O sub(3).4SiO sub(2)) → 3 Al sub(2) O sub(3). 2SiO sub(2) + 10 (SiO sub(2)) Pyrophyllite Anhydride Mullite Cristobalite, were studied by Transmission Electron Microscopy (TEM) associated to Selected Area Electron Diffraction (SAD), applied to a very pure sample, colected at Diamantina, M.G. Some other tgechniques were also used, as X-ray Diffraction (XRD), Differential Thermal Analysis (DTA) and Thermogravimetric Analysis (TGA), applied to other different Pyrophyllite samples. A thermodynamical theoretical study was undertaken to estimate the values for the entropyu of formation, enthalpy and molar thermal capacity for the Pyrophyllite Anhydride. (author)

  1. Mineral phases and metals in baghouse dust from secondary aluminum production

    Science.gov (United States)

    Baghouse dust (BHD) is a solid waste generated by air pollution control systems during secondary aluminum processing (SAP). Management and disposal of BHD can be challenging in the U.S. and elsewhere. In this study, the mineral phases, metal content and metal leachability of 78...

  2. Saturation of the hydroxyapatite mineral phase using radioactive fluorine; Saturacion de la fase mineral hidroxiapatita utilizando fluor radiactivo

    Energy Technology Data Exchange (ETDEWEB)

    Flores de la Torre, J.A.; Badillo A, V.E. [Universidad Autonoma de Zacatecas, 98000 Zacatecas (Mexico); Lopez D, F.A. [Unidad PET Ciclotron, Facultad de Medicina, UNAM, 04510 Mexico D.f. (Mexico)]. e-mail: ebadillo@cantera.reduaz.mx

    2005-07-01

    With the purpose of knowing the Anion exchange capacity (CIA) of the hydroxyapatite mineral phase, marketed by BIO-RAD, becomes necessary to saturate the surface of the mineral with an anion specie that possesses a strong affinity by this solid as it is the case of the fluorine. Moreover it takes advantage that offers the radioactive tracer technique, using the radioactive isotope of the fluorine, {sup 18}F, produced in the cyclotron of the UNAM. This saturation is obtained in terms of the quantity of retained fluorine (mmol/ 100 g) in the synthetic hydroxyapatite in function of the concentration of the solution of NaF that oscillates from 0.7 M up to 0.16 M to fixed values of pH of 9.2. Those results demonstrate that to this fixed pH value the saturation of the surface of the hydroxyapatite is achieved in approximately 30 mmol/ 100 g, using important concentrations of NaF that correspond to 0.14 M from now on. This result demonstrates the high capacity of the solid considered to retain considerable quantities of fluorine even to basic pH values. (Author)

  3. Nanoscale Phase Stability Reversal During the Nucleation and Growth of Titanium Oxide Minerals

    Science.gov (United States)

    Hummmer, D. R.; Heaney, P. J.; Kubicki, J. D.; Kent, P. R.; Post, J. E.

    2008-12-01

    Fine-grained titanium oxide minerals are important in soils, where they affect a variety of geochemical processes. They are also industrially important as catalysts, pigments, food additives, and dielectrics. Recent research has indicated an apparent reversal of thermodynamic stability between TiO2 phases at the nanoscale thought to be caused by an increased contribution of surface energy to the total free energy. Time-resolved X-ray diffraction (XRD) experiments in which titanium oxides crystallize from aqueous TiCl4 solutions confirm that anatase, a metastable phase, is always the first phase to nucleate under our range of initial conditions. Rutile peaks are observed only minutes after the first appearance of anatase, after which anatase abundance slowly decreases while rutile continues to form. Whole pattern refinement of diffraction data reveals that lattice constants of both phases increase throughout the crystallization process. In addition, transmission electron microscope (TEM) observations and kinetic modeling indicate that anatase does not undergo a solid-state transformation to the rutile structure as once thought. Instead, anatase appears to re-dissolve and then feed the growth of already nucleated rutile nanocrystals. Density functional theory (DFT) calculations were employed to model 1, 2, and 3 nm particles of both mineral phases. The total surface energies calculated from these models did yield lower values for anatase than for rutile by 8-13 kJ/mol depending on particle size, indicating that surface free energy is sufficient to account for stability reversal. However, these whole-particle surface energies were much higher than the sum of energies of each particle's constituent crystallographic surfaces. We attribute the excess energy to defects associated with the edges and corners of nanoparticles, which are not present on a 2-D periodic surface. This previously unreported edge and corner energy may play a dominant role in the stability reversal

  4. PHASE ANALYSES OF URANIUM BEARING MINERALS FROM THE HIGH GRADE ORE, NOPAL I, PENA BLANCA, MEXICO

    International Nuclear Information System (INIS)

    Ren, M.; Goodell, P.; Kelts, A.; Anthony, E.Y.; Fayek, M.; Fan, C.; Beshears, C.

    2005-01-01

    The Nopal I uranium deposit is located in the Pena Blanca district, approximately 40 miles north of Chihuahua City, Mexico. The deposit was formed by hydrothermal processes within the fracture zone of welded silicic volcanic tuff. The ages of volcanic formations are between 35 to 44 m.y. and there was secondary silicification of most of the formations. After the formation of at least part of the uranium deposit, the ore body was uplifted above the water table and is presently exposed at the surface. Detailed petrographic characterization, electron microprobe backscatter electron (BSE) imagery, and selected x-ray maps for the samples from Nopal I high-grade ore document different uranium phases in the ore. There are at least two stages of uranium precipitation. A small amount of uraninite is encapsulated in silica. Hexavalent uranium may also have been a primary precipitant. The uranium phases were precipitated along cleavages of feldspars, and along fractures in the tuff. Energy dispersive spectrometer data and x-ray maps suggest that the major uranium phases are uranophane and weeksite. Substitutions of Ca and K occur in both phases, implying that conditions were variable during the mineralization/alteration process, and that compositions of the original minerals have a major influence on later stage alteration. Continued study is needed to fully characterize uranium behavior in these semi-arid to arid conditions

  5. Dynamics of mineral crystallization from precipitated slab-derived fluid phase: first in situ synchrotron X-ray measurements

    Science.gov (United States)

    Malaspina, Nadia; Alvaro, Matteo; Campione, Marcello; Wilhelm, Heribert; Nestola, Fabrizio

    2015-03-01

    Remnants of the fluid phase at ultrahigh pressure (UHP) in subduction environments may be preserved as primary multiphase inclusions in UHP minerals. The mode of crystallization of daughter minerals during precipitation within the inclusion and/or the mechanism of interaction between the fluid at supercritical conditions and the host mineral are still poorly understood from a crystallographic point of view. A case study is represented by garnet-orthopyroxenites from the Maowu Ultramafic Complex (China) deriving from harzburgite precursors metasomatized at ~4 GPa, 750 °C by a silica- and incompatible trace element-rich fluid phase. This metasomatism produced poikilitic orthopyroxene and inclusion-rich garnet porphyroblasts. Solid multiphase primary inclusions in garnet display a size within a few tens of micrometres and negative crystal shapes. Infilling minerals (spinel: 10-20 vol%; amphibole, chlorite, talc, mica: 80-90 vol%) occur with constant volume proportions and derive from trapped solute-rich aqueous fluids. To constrain the possible mode of precipitation of daughter minerals, we performed for the first time a single-crystal X-ray diffraction experiment by synchrotron radiation at Diamond Light Source. In combination with electron probe microanalyses, this measurement allowed the unique identification of each mineral phase and reciprocal orientations. We demonstrated the epitaxial relationship between spinel and garnet and between some hydrous minerals. Such information is discussed in relation to the physico-chemical aspects of nucleation and growth, shedding light on the mode of mineral crystallization from a fluid phase trapped at supercritical conditions.

  6. Mineral and Nutrient Leaf Composition of Two Cassava (Manihot esculenta Crantz Cultivars Defoliated at Varying Phenological Phases

    Directory of Open Access Journals (Sweden)

    Oyeyemi Adigun DADA

    2010-12-01

    Full Text Available The effect of defoliation on mineral and food value of two cassava varieties defoliated at varying phenological phases was studied to ascertain the appropriate phenological phase when harvested leaves would contain the optimum mineral and proximate composition, gross energy and the least cyanide content. Two cassava cultivars were subjected to defoliation at varying phenological stages including logarithmic, vegetative and physiological maturity phases. The mineral content was highest at the logarithmic phase than any other phases. The proximate composition of the cassava leaves showed that crude protein was highest at physiological maturity, while the least HCN was observed in cassava defoliated at logarithmic phase. Analysis of mineral and proximate content showed that leaf of the �TMS30572� cultivar had the highest mineral content, fat, fibre, ash, dry matter and gross energy at the logarithm phase while �Oko-Iyawo� had the highest crude protein and HCN at physiological maturity. This study indicates the high potential of cassava leaf as an unconventional source of protein for both humans and animals when defoliated at logarithmic growth phase.

  7. Stabilization of organic matter in soils: role of amorphous mineral phases

    Science.gov (United States)

    Zewde Tamrat, Wuhib; Rose, Jérôme; Levard, Clément; Chaurand, Perrine; Basile-Doelsch, Isabelle

    2016-04-01

    Soil organic matter (SOM) globally contributes the largest portion of continental carbon stock. One major issue concerning this large C pool includes its instability by mineralization and erosion due to land use. The main hypothesis of this work is that physicochemical stabilization of SOM is mainly driven by interactions of organic compounds, not with mineral surfaces as classically considered, but with amorphous polymers continuously formed by the alteration of soil minerals(1-3). Our objective is to understand how nano-organomineral complexes (nCOMx) are structured at the nanoscale, assess mechanisms of their formation, and quantify the effects of their occurrence on SOM turnovers. Due to inherent high complexity of natural samples, our methodology is based on the formation of nCOMx from both synthetic systems and natural mineral-weathered components. For the mineral component, biotite (from Bancroft, Canada) was selected. For the organic component, 3,4-Dihydroxy-L-phenylalanine, an amino acid with hydroxyl (pKa=9.95), carboxyl (pKa=2,58), amino (pKa=9,24) and an aromatic functions was chosen. The methodology aimed at developing conditions that generate biotite dissolution and nCOMx precipitation. The second step of the experiment consisted of the precipitation of nCOMx by slowly increasing pH over 3 to 12 hours of hydrolysis. Three final pH conditions were tested (4.2, 5 and 7) with Metal/Carbon ratios of 0.01, 0.1, 1, 10 and 'No Carbon'. The first results of dissolution rates and congruency, AFM imaging, ICPMS, HR-TEM and XRD as well as XAS characterizations (transmission and florescence mode at the Fe K-edge) of nCOMx will be presented. Experiments and analysis techniques were designed to study these synthetic phases with regard to Si, Al, Fe and OM proportions to increase the OM proportion (as in natural soil phases) and also increase the stability of the OM phase (as in increased residence time of OM in the soil). We will focus particularly on the Fe state

  8. The competition between mineral dust and soot ice nuclei in mixed-phase clouds (Invited)

    Science.gov (United States)

    Murray, B. J.; Atkinson, J.; Umo, N.; Browse, J.; Woodhouse, M. T.; Whale, T.; Baustian, K. J.; Carslaw, K. S.; Dobbie, S.; O'Sullivan, D.; Malkin, T. L.

    2013-12-01

    The amount of ice present in mixed-phase clouds, which contain both supercooled liquid water droplets and ice particles, affects cloud extent, lifetime, particle size and radiative properties. The freezing of cloud droplets can be catalysed by the presence of aerosol particles known as ice nuclei. In this talk our recent laboratory and global aerosol modelling work on mineral dust and soot ice nuclei will be presented. We have performed immersion mode experiments to quantify ice nucleation by the individual minerals which make up desert mineral dusts and have shown that the feldspar component, rather than the clay component, is most important for ice nucleation (Atkinson et al. 2013). Experiments with well-characterised soot generated with eugenol, an intermediate in biomass burning, and n-decane show soot has a significant ice nucleation activity in mixed-phase cloud conditions. Our results for soot are in good agreement with previous results for acetylene soot (DeMott, 1990), but extend the efficiency to much higher temperatures. We then use a global aerosol model (GLOMAP) to map the distribution of soot and feldspar particles on a global basis. We show that below about -15oC that dust and soot together can explain most observed ice nuclei in the Earth's atmosphere, while at warmer temperatures other ice nuclei types are needed. We show that in some regions soot is the most important ice nuclei (below -15oC), while in others feldspar dust dominates. Our results suggest that there is a strong anthropogenic contribution to the ice nuclei population, since a large proportion of soot aerosol in the atmosphere results from human activities. Atkinson, J. D., Murray, B. J., Woodhouse, M. T., Carslaw, K. S., Whale, T. F., Baustian, K. J., Dobbie, S., O'Sullivan, D., and Malkin, T. L.: The importance of feldspar for ice nucleation by mineral dust in mixed-phase clouds, Nature, 10.1038/nature12278, (2013). Demott, P. J. 1990. An Exploratory-Study of Ice Nucleation by Soot

  9. A U-bearing composite waste form for electrochemical processing wastes

    Energy Technology Data Exchange (ETDEWEB)

    Chen, X.; Ebert, W. L.; Indacochea, J. E.

    2018-04-01

    Metallic/ceramic composite waste forms are being developed to immobilize combined metallic and oxide waste streams generated during electrochemical recycling of used nuclear fuel. Composites were made for corrosion testing by reacting HT9 steel to represent fuel cladding, Zr and Mo to simulate metallic fuel waste, and a mixture of ZrO2, Nd2O3, and UO2 to represent oxide wastes. More than half of the added UO2 was reduced to metal and formed Fe-Zr-U intermetallics and most of the remaining UO2 and all of the Nd2O3 reacted to form zirconates. Fe-Cr-Mo intermetallics were also formed. Microstructure characterization of the intermetallic and ceramic phases that were generated and tests conducted to evaluate their corrosion behaviors indicate composite waste forms can accommodate both metallic and oxidized waste streams in durable host phases. (c) 2018 Elsevier B.V. All rights reserved.

  10. Durability of crystalline phase in concrete microstructure modified by the mineral powders: evaluation by nanoindentation tests

    Directory of Open Access Journals (Sweden)

    Rajczakowska Magdalena

    2016-03-01

    Full Text Available This paper presents the nanoindentation investigation of the evolution of concrete microstructure modified by the Internal Crystallization Technology mineral powders. The samples under study were retrieved from a fragment of a circular concrete lining of the vertical mine shaft at a depth of approximately 1,000 m. Due to the aggressive environment and exposure to contaminated water, the internal surface of the structure was deteriorated, decreasing its strength significantly. The mineral powders were applied directly on the surface lining. The specimens were investigated one month, three months and one year after the application of the aforementioned substance in order to verify the time dependence of the strengthening processes and durability of the crystalline phase. The microstructural changes of concrete were assessed with the use of nanoindentation technique. The testing procedure involved including the previously cut specimens in the epoxy resin and grinding and polishing in order to reduce the surface roughness. As a result of the nanoindentation tests the hardness as well as Young’s modulus of the material were evaluated. The results were then compared and statistically analyzed. As a consequence, the disintegration time of the crystalline network in the pores of concrete was identified.

  11. Mineral and chemical composition of rock core and surface gas composition in Horonobe Underground Research Laboratory project. Phase 1

    International Nuclear Information System (INIS)

    Hiraga, Naoto; Ishii, Eiichi

    2008-02-01

    The following three kinds of analyses were conducted for the 1st phase of the Horonobe Underground Research Laboratory Project. Mineral composition analysis of core sample. Whole rock chemical composition analysis of core sample. Surface gas composition analysis. This document summarizes the results of these analyses. (author)

  12. Anelasticity maps for acoustic dissipation associated with phase transitions in minerals

    Science.gov (United States)

    Carpenter, Michael A.; Zhang, Zhiying

    2011-07-01

    Acoustic dissipation due to structural phase transitions in minerals could give rise to large seismic attenuation effects superimposed on the high temperature background contribution from dislocations and grain boundaries in the Earth. In addition to the possibility of a sharp peak actually at a transition point for both compressional and shear waves, significant attenuation might arise over wider temperature intervals due to the mobility of transformation twins or other defects associated with the transition. Attenuation due to structural phase transitions in quartz, pyroxenes, perovskites, stishovite and hollandite, or to spin state transitions of Fe2+ in magnesiowüstite and perovskite and the hcp/bcc transition in iron-nickel (Fe-Ni) alloy, are reviewed from this perspective. To these can be added possible loss behaviour associated with reconstructive transitions which might occur by a ledge mechanism on topotactic interfaces (orthopyroxene/clinopyroxene, olivine/spinel and perovskite/postperovskite), with impurities (Snoek effect) or with mobility of protons. There are experimental difficulties associated with measuring dissipation effects in situ at simultaneous high pressures and temperatures, so reliance is currently placed on investigation of analogue phases such as LaCoO3 for spin-state behaviour and LaAlO3 for the dynamics of ferroelastic twin walls. Similarly, it is not possible to measure loss dynamics simultaneously at the low stresses and low frequencies that pertain in seismic waves, so reliance must be placed on combining different techniques, such as dynamic mechanical analysis (low frequency, relatively high stress) and resonant ultrasound spectroscopy (high frequency, low stress), to extrapolate acoustic loss behaviour over wide frequency, temperature and stress intervals. In this context 'anelasticity maps' provide a convenient means of representing different loss mechanisms. Contouring of the inverse mechanical quality factor, Q-1, can be

  13. Phase Composition Maps integrate mineral compositions with rock textures from the micro-meter to the thin section scale

    Science.gov (United States)

    Willis, Kyle V.; Srogi, LeeAnn; Lutz, Tim; Monson, Frederick C.; Pollock, Meagen

    2017-12-01

    Textures and compositions are critical information for interpreting rock formation. Existing methods to integrate both types of information favor high-resolution images of mineral compositions over small areas or low-resolution images of larger areas for phase identification. The method in this paper produces images of individual phases in which textural and compositional details are resolved over three orders of magnitude, from tens of micrometers to tens of millimeters. To construct these images, called Phase Composition Maps (PCMs), we make use of the resolution in backscattered electron (BSE) images and calibrate the gray scale values with mineral analyses by energy-dispersive X-ray spectrometry (EDS). The resulting images show the area of a standard thin section (roughly 40 mm × 20 mm) with spatial resolution as good as 3.5 μm/pixel, or more than 81 000 pixels/mm2, comparable to the resolution of X-ray element maps produced by wavelength-dispersive spectrometry (WDS). Procedures to create PCMs for mafic igneous rocks with multivariate linear regression models for minerals with solid solution (olivine, plagioclase feldspar, and pyroxenes) are presented and are applicable to other rock types. PCMs are processed using threshold functions based on the regression models to image specific composition ranges of minerals. PCMs are constructed using widely-available instrumentation: a scanning-electron microscope (SEM) with BSE and EDS X-ray detectors and standard image processing software such as ImageJ and Adobe Photoshop. Three brief applications illustrate the use of PCMs as petrologic tools: to reveal mineral composition patterns at multiple scales; to generate crystal size distributions for intracrystalline compositional zones and compare growth over time; and to image spatial distributions of minerals at different stages of magma crystallization by integrating textures and compositions with thermodynamic modeling.

  14. Preservation in microbial mats: mineralization by a talc-like phase of a fish embedded in a microbial sarcophagus

    Science.gov (United States)

    Iniesto, Miguel; Zeyen, Nina; López-Archilla, Ana; Bernard, Sylvain; Buscalioni, Ángela; Guerrero, M. Carmen; Benzerara, Karim

    2015-09-01

    Microbial mats have been repeatedly suggested to promote early fossilization of macroorganisms. Yet, experimental simulations of this process remain scarce. Here, we report results of 5 year-long experiments performed onfish carcasses to document the influence of microbial mats on mineral precipitation during early fossilization. Carcasses were initially placed on top of microbial mats. After two weeks, fishes became coated by the mats forming a compact sarcophagus, which modified the microenvironment close to the corpses. Our results showed that these conditions favoured the precipitation of a poorly crystalline silicate phase rich in magnesium. This talc-like mineral phase has been detected in three different locations within the carcasses placed in microbial mats for more than 4 years: 1) within inner tissues, colonized by several bacillary cells; 2) at the surface of bones of the upper face of the corpse buried in the mat; and 3) at the surface of several bones such as the dorsal fin which appeared to be gradually replaced by the Mg-silicate phase. This mineral phase has been previously shown to promote bacteria fossilization. Here we provide first experimental evidence that such Mg-rich phase can also be involved in exceptional preservation of animals.

  15. Mineral phases of green liquor dregs, slaker grits, lime mud and wood ash of a Kraft pulp and paper mill

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Fernanda Machado [Laboratorio de Quimica Mineral Aplicada, Departamento de Quimica-UFPR, Universidade Federal do Parana (UFPR), CP 19081, CEP 81531990, Curitiba-PR (Brazil); Munhoz Martins, Joaniel [Laboratorio de Analise de Minerais e Rochas (LAMIR-UFPR) (Brazil); Ferracin, Luiz Carlos [Laboratorio Quimico da Votorantin Cimentos (Brazil); Cunha, Carlos Jorge da [Laboratorio de Quimica Mineral Aplicada, Departamento de Quimica-UFPR, Universidade Federal do Parana (UFPR), CP 19081, CEP 81531990, Curitiba-PR (Brazil)]. E-mail: cjdcunha@quimica.ufpr.br

    2007-08-17

    Four residues generated in a Kraft, pulp and paper plant, were characterized by X-ray fluorescence spectroscopy (XFA), powder X-ray diffraction (XRD), thermogravimmetric analysis (TG) and Fourier transform infrared spectroscopy (FTIR). A quantitative phase composition model, that accounts for the observed data and for the physico-chemical conditions of formation, was postulated for each material. Emphasis was given on the identification of the mineral components of each material. The green liquor dregs and the lime mud contain Calcite and Gipsite. The slaker grits contains Calcite, Portlandite, Pirssonite, Larnite and Brucite. The Calcite phase, present in the dregs and in the lime mud, has small amounts of magnesium replacing calcium. The wood ash contains Quartz as the major crystalline mineral phase.

  16. Mineral phases of green liquor dregs, slaker grits, lime mud and wood ash of a Kraft pulp and paper mill

    International Nuclear Information System (INIS)

    Martins, Fernanda Machado; Munhoz Martins, Joaniel; Ferracin, Luiz Carlos; Cunha, Carlos Jorge da

    2007-01-01

    Four residues generated in a Kraft, pulp and paper plant, were characterized by X-ray fluorescence spectroscopy (XFA), powder X-ray diffraction (XRD), thermogravimmetric analysis (TG) and Fourier transform infrared spectroscopy (FTIR). A quantitative phase composition model, that accounts for the observed data and for the physico-chemical conditions of formation, was postulated for each material. Emphasis was given on the identification of the mineral components of each material. The green liquor dregs and the lime mud contain Calcite and Gipsite. The slaker grits contains Calcite, Portlandite, Pirssonite, Larnite and Brucite. The Calcite phase, present in the dregs and in the lime mud, has small amounts of magnesium replacing calcium. The wood ash contains Quartz as the major crystalline mineral phase

  17. Estimation of the reactive mineral surface area during CO2-rich fluid-rock interaction: the influence of neogenic phases

    Science.gov (United States)

    Scislewski, A.; Zuddas, P.

    2010-12-01

    Mineral dissolution and precipitation reactions actively participate to control fluid chemistry during water-rock interaction. It is however, difficult to estimate and well normalize bulk reaction rates if the mineral surface area exposed to the aqueous solution and effectively participating on the reactions is unknown. We evaluated the changing of the reactive mineral surface area during the interaction between CO2-rich fluids and Albitite/Granitoid rocks (similar mineralogy but different abundances), reacting under flow-through conditions. Our methodology, adopting an inverse modeling approach, is based on the estimation of dissolution rate and reactive surface area of the different minerals participating in the reactions by the reconstruction the chemical evolution of the interacting fluids. The irreversible mass-transfer processes is defined by a fractional degree of advancement, while calculations were carried out for Albite, Microcline, Biotite and Calcite assuming that the ion activity of dissolved silica and aluminium ions was limited by the equilibrium with quartz and kaolinite. Irrespective of the mineral abundance in granite and albitite, we found that mineral dissolution rates did not change significantly in the investigated range of time where output solution’s pH remained in the range between 6 and 8, indicating that the observed variation in fluid composition depends not on pH but rather on the variation of the parent mineral’s reactive surface area. We found that the reactive surface area of Albite varied by more than 2 orders of magnitude, while Microcline, Calcite and Biotite surface areas changed by 1-2 orders of magnitude. We propose that parent mineral chemical heterogeneity and, particularly, the stability of secondary mineral phases may explain the observed variation of the reactive surface area of the minerals. Formation of coatings at the dissolving parent mineral surfaces significantly reduced the amount of surface available to react

  18. Effect of the mineral precipitation-dissolution at tunnel walls during the operational and post-operational phases

    Energy Technology Data Exchange (ETDEWEB)

    Domenech, Cristina; Arcos, David; Duro, Lara; Grandia, Fidel [Enviros Consul ting, Valldoreix, Barcelona (Spain)

    2007-11-15

    The extent of reversibility of the geochemical conditions disturbed during the construction and operational phases is of importance in order to assess the chemical evolution of the repository system. In this regard, it is essential to have a deep understanding of the chemical status of the repository system at closure in order to describe its immediate geochemical evolution beyond this point. This project assesses the dissolution and precipitation of minerals due to the interaction with groundwater in the deposition tunnel wall-rock during the operational phase (prior to tunnel backfilling) and during the saturation phase, also considering the effect on the backfill material. We have performed a 2D model in which a fracture intersecting the main tunnel has been considered. The project has been developed in two consecutive stages. The first stage simulates the precipitation and dissolution of minerals in the tunnel wall rock during the operational phase (100 years after excavation) when the tunnel is empty and filled with air. During this stage, water flows through fractures into the tunnel. The results of the model suggest that the interaction between groundwater, fracture-filling minerals, and atmospheric O{sub 2}(g) and CO{sub 2}(g) present in the tunnel leads to the precipitation of secondary minerals (calcite and iron(III) oxy-hydroxide) that do not significantly affect the porosity of the area surrounding the tunnel. The second stage starts after the operational phase, once the tunnel is backfilled, and simulates the interaction of groundwater with fracture-filling minerals and the backfill material. The model implemented assumes that the backfill is already water saturated and that water flows following the regional head gradient. Moreover, it also assumes that O2(g) is still present in the tunnel wall, as a result of the operational phase disturbances. The results show that oxygen will oxidise pyrite in the backfill and promote the precipitation of Fe

  19. Removal of uranium(VI) from the aqueous phase by iron(II) minerals in presence of bicarbonate

    Energy Technology Data Exchange (ETDEWEB)

    Regenspurg, Simona, E-mail: regens@gfz-potsdam.de [Industrial Ecology, Royal Institute of Technology (KTH), SE 10044 Stockholm (Sweden); Schild, Dieter; Schaefer, Thorsten; Huber, Florian [Institut fuer Nukleare Entsorgung (INE), Forschungszentrum Karlsruhe, 76344 Eggenstein-Leopoldshafen (Germany); Malmstroem, Maria E. [Industrial Ecology, Royal Institute of Technology (KTH), SE 10044 Stockholm (Sweden)

    2009-09-15

    Uranium(VI) mobility in groundwater is strongly affected by sorption of mobile U(VI) species (e.g. uranyl, UO{sub 2}{sup 2+}) to mineral surfaces, precipitation of U(VI) compounds, such as schoepite (UO{sub 2}){sub 4}O(OH){sub 6}.6H{sub 2}O), and by reduction to U(IV), forming sparingly soluble phases (uraninite; UO{sub 2}). The latter pathway, in particular, would be very efficient for long-term immobilization of U. In nature, Fe(II) is an important reducing agent for U(VI) because it frequently occurs either dissolved in natural waters, sorbed to matrix minerals, or structurally bound in many minerals. Redox reactions between U(VI) and Fe(II) depend not only on the availability of Fe(II) in the environment, but also on the chemical conditions in the aqueous solution. Under natural groundwater condition U(VI) forms complexes with many anionic ligands, which strongly affect its speciation. Carbonate, in particular, is known to form stable complexes with U, raising the question, if U(VI), when complexed by carbonate, can be reduced to UO{sub 2}. The goal of this study was to find out if Fe(II) when structurally bound in a mineral (as magnetite, Fe{sub 3}O{sub 4}) or sorbed to a mineral surface (as corundum, Al{sub 2}O{sub 3}) can reduce U(VI) to U(IV) in the presence of HCO{sub 3}{sup -}. Batch experiments were conducted under anaerobic conditions to observe U removal from the aqueous phase by the two minerals depending on HCO{sub 3}{sup -} addition (1 mM), U concentration (0.01-30 {mu}M) and pH value (6-10). Immediately after the experiments, the mineral surfaces were analyzed by X-ray photoelectron spectroscopy (XPS) to obtain information on the redox state of U bound to the solid surfaces. XPS results gave evidence that U(VI) can be reduced both by magnetite and by corundum amended with Fe(II). In the presence of HCO{sub 3}{sup -} the amount of reduced U on the mineral surfaces increased compared to carbonate-free solutions. This can be explained by the formation

  20. Methodology for determination of trace elements in mineral phases of iron banded formation by LA-ICP-MS

    International Nuclear Information System (INIS)

    Sousa, Denise V.M. de; Nalini Junior, Herminio A.; Sampaio, Geraldo M.S.; Abreu, Adriana T. de; Lana, Cristiano de C.

    2015-01-01

    The study of the chemical composition of mineral phases of iron formation (FF), especially of trace elements, is an important tool in the understanding of the genesis of these rocks and the contribution of the phases in the composition of whole rock. Low mass fraction of such elements in the mineral phases present in this rock type requires a suitable analytical procedure. The laser ablation technique coupled with ICP-MS (LA-ICP-MS) has been widely used for determination of trace elements in geological samples. Thus, the aim of this study is to develop calibration curves for determination of trace elements (Y, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb and Lu) in mineral phases of banded iron formations by LA-ICP-MS. Several certified reference materials (CRM) were used for calibrate the equipment. The analytical conditions were checked by CRM NIST SRM 614. The results were satisfactory, since the curves showed good linearity coefficients, good accuracy and precision of results. (author)

  1. Trace metals partitioning among different sedimentary mineral phases and the deposit-feeding polychaete Armandia brevis

    International Nuclear Information System (INIS)

    Díaz-de-Alba, Margarita; Huerta-Diaz, Miguel Angel; Delgadillo-Hinojosa, Francisco; Hare, Landis; Galindo-Riaño, M. Dolores; Siqueiros-Valencia, Arturo

    2016-01-01

    Trace metals (Cd, Co, Cu, Fe, Mn, Ni, Pb, Zn) were determined in two operationally defined fractions (HCl and pyrite) in sediments from Ensenada and El Sauzal harbors (Mexico). The HCl fraction had significantly higher metal concentrations relative to the pyrite fraction in both harbors, underlining the weak tendency of most trace metals to associate with pyrite. Exceptionally, Cu was highly pyritized, with degrees of trace metal pyritization (DTMP) > 80% in both harbors. Dissolved Fe flux measurements combined with solid phase Fe sulfide data indicated that 98 mt of Fe are precipitated as iron sulfides every year in Ensenada Harbor. These Fe sulfides (and associated trace metals) will remain preserved in the sediments, unless they are perturbed by dredging or sediment resuspension. Calculations indicate that dredging activities could export to the open ocean 0.20 ± 0.13 to (0.30 ± 0.56) × 10"3 mt of Cd and Cu, respectively, creating a potential threat to marine benthic organisms. Degrees of pyritization (DOP) values in Ensenada and El Sauzal harbors were relatively low (< 25%) while degrees of sulfidization (DOS) were high (~ 50%) because of the contribution of acid volatile sulfide. DOP values correlated with DTMP values (p ≤ 0.001), indicating that metals are gradually incorporated into pyrite as this mineral is formed. Significant correlations were also found between DTMP values and − log(K_s_p_(_M_e_S_)/K_s_p_(_p_y_r_)) for both harbors, indicating that incorporation of trace metals into the pyrite phase is a function of the solubility product of the corresponding metal sulfide. The order in which elements were pyritized in both harbors was Zn ≈ Mn < Fe < Cd ≈ Pb < Ni ≈ Co < < Cu. Lastly, a strong correlation (r"2 = 0.87, p < 0.01) was found between average reactive trace metal concentrations and metal concentrations measured in Armandia brevis (a deposit-feeding Opheliid polychaete), suggesting that these labile sedimentary metals are

  2. Trace metals partitioning among different sedimentary mineral phases and the deposit-feeding polychaete Armandia brevis

    Energy Technology Data Exchange (ETDEWEB)

    Díaz-de-Alba, Margarita [Department of Analytical Chemistry, Institute of Biomolecules (INBIO), Faculty of Sciences, CEI-MAR, University of Cadiz, Campus Rio S. Pedro, E-11510, Puerto Real, Cadiz (Spain); Huerta-Diaz, Miguel Angel, E-mail: huertam@uabc.edu.mx [Instituto de Investigaciones Oceanológicas, Universidad Autónoma de Baja California, Campus Ensenada, Km. 103 Carr. Tijuana-Ensenada, Ensenada 22800, Baja California (Mexico); Delgadillo-Hinojosa, Francisco [Instituto de Investigaciones Oceanológicas, Universidad Autónoma de Baja California, Campus Ensenada, Km. 103 Carr. Tijuana-Ensenada, Ensenada 22800, Baja California (Mexico); Hare, Landis [Centre Eau Terre Environnement, 490, rue de la Couronne, Québec, Québec G1K 9A9 (Canada); Galindo-Riaño, M. Dolores [Department of Analytical Chemistry, Institute of Biomolecules (INBIO), Faculty of Sciences, CEI-MAR, University of Cadiz, Campus Rio S. Pedro, E-11510, Puerto Real, Cadiz (Spain); Siqueiros-Valencia, Arturo [Instituto de Investigaciones Oceanológicas, Universidad Autónoma de Baja California, Campus Ensenada, Km. 103 Carr. Tijuana-Ensenada, Ensenada 22800, Baja California (Mexico)

    2016-02-01

    Trace metals (Cd, Co, Cu, Fe, Mn, Ni, Pb, Zn) were determined in two operationally defined fractions (HCl and pyrite) in sediments from Ensenada and El Sauzal harbors (Mexico). The HCl fraction had significantly higher metal concentrations relative to the pyrite fraction in both harbors, underlining the weak tendency of most trace metals to associate with pyrite. Exceptionally, Cu was highly pyritized, with degrees of trace metal pyritization (DTMP) > 80% in both harbors. Dissolved Fe flux measurements combined with solid phase Fe sulfide data indicated that 98 mt of Fe are precipitated as iron sulfides every year in Ensenada Harbor. These Fe sulfides (and associated trace metals) will remain preserved in the sediments, unless they are perturbed by dredging or sediment resuspension. Calculations indicate that dredging activities could export to the open ocean 0.20 ± 0.13 to (0.30 ± 0.56) × 10{sup 3} mt of Cd and Cu, respectively, creating a potential threat to marine benthic organisms. Degrees of pyritization (DOP) values in Ensenada and El Sauzal harbors were relatively low (< 25%) while degrees of sulfidization (DOS) were high (~ 50%) because of the contribution of acid volatile sulfide. DOP values correlated with DTMP values (p ≤ 0.001), indicating that metals are gradually incorporated into pyrite as this mineral is formed. Significant correlations were also found between DTMP values and − log(K{sub sp(MeS)}/K{sub sp(pyr)}) for both harbors, indicating that incorporation of trace metals into the pyrite phase is a function of the solubility product of the corresponding metal sulfide. The order in which elements were pyritized in both harbors was Zn ≈ Mn < Fe < Cd ≈ Pb < Ni ≈ Co < < Cu. Lastly, a strong correlation (r{sup 2} = 0.87, p < 0.01) was found between average reactive trace metal concentrations and metal concentrations measured in Armandia brevis (a deposit-feeding Opheliid polychaete), suggesting that these labile sedimentary metals are

  3. The role of upper mantle mineral phase transitions on the current structure of large-scale Earth's mantle convection.

    Science.gov (United States)

    Thoraval, C.

    2017-12-01

    Describing the large-scale structures of mantle convection and quantifying the mass transfer between upper and lower mantle request to account for the role played by mineral phase transitions in the transition zone. We build a density distribution within the Earth mantle from velocity anomalies described by global seismic tomographic models. The density distribution includes thermal anomalies and topographies of the phase transitions at depths of 410 and 660 km. We compute the flow driven by this density distribution using a 3D spherical circulation model, which account for depth-dependent viscosity. The dynamic topographies at the surface and at the CMB and the geoid are calculated as well. Within the range of viscosity profiles allowing for a satisfying restitution of the long wavelength geoid, we perform a parametric study to decipher the role of the characteristics of phase diagrams - mainly the Clapeyron's slopes - and of the kinetics of phase transitions, which may modify phase transition topographies. Indeed, when a phase transition is delayed, the boundary between two mineral phases is both dragged by the flow and interfere with it. The results are compared to recent estimations of surface dynamic topography and to the phase transition topographies as revealed by seismic studies. The consequences are then discussed in terms of structure of mantle flow. Comparisons between various tomographic models allow us to enlighten the most robust features. At last, the role played by the phase transitions on the lateral variations of mass transfer between upper and lower mantle are quantified by comparison to cases with no phase transitions and confronted to regional tomographic models, which reflect the variability of the behaviors of the descending slabs in the transition zone.

  4. Generation of composites for bone tissue-engineering applications consisting of gellan gum hydrogels mineralized with calcium and magnesium phosphate phases by enzymatic means.

    Science.gov (United States)

    Douglas, Timothy E L; Krawczyk, Grzegorz; Pamula, Elzbieta; Declercq, Heidi A; Schaubroeck, David; Bucko, Miroslaw M; Balcaen, Lieve; Van Der Voort, Pascal; Bliznuk, Vitaliy; van den Vreken, Natasja M F; Dash, Mamoni; Detsch, Rainer; Boccaccini, Aldo R; Vanhaecke, Frank; Cornelissen, Maria; Dubruel, Peter

    2016-11-01

    Mineralization of hydrogels, desirable for bone regeneration applications, may be achieved enzymatically by incorporation of alkaline phosphatase (ALP). ALP-loaded gellan gum (GG) hydrogels were mineralized by incubation in mineralization media containing calcium and/or magnesium glycerophosphate (CaGP, MgGP). Mineralization media with CaGP:MgGP concentrations 0.1:0, 0.075:0.025, 0.05:0.05, 0.025:0.075 and 0:0.1 (all values mol/dm 3 , denoted A, B, C, D and E, respectively) were compared. Mineral formation was confirmed by IR and Raman, SEM, ICP-OES, XRD, TEM, SAED, TGA and increases in the the mass fraction of the hydrogel not consisting of water. Ca was incorporated into mineral to a greater extent than Mg in samples mineralized in media A-D. Mg content and amorphicity of mineral formed increased in the order A hydroxyapatite (CDHA). Mineral formed in medium C was a combination of CDHA and an amorphous phase. Mineral formed in medium D was an amorphous phase. Mineral formed in medium E was a combination of crystalline and amorphous MgP. Young's moduli and storage moduli decreased in dependence of mineralization medium in the order A > B > C > D, but were significantly higher for samples mineralized in medium E. The attachment and vitality of osteoblastic MC3T3-E1 cells were higher on samples mineralized in media B-E (containing Mg) than in those mineralized in medium A (not containing Mg). All samples underwent degradation and supported the adhesion of RAW 264.7 monocytic cells, and samples mineralized in media A and B supported osteoclast-like cell formation. Copyright © 2014 John Wiley & Sons, Ltd. Copyright © 2014 John Wiley & Sons, Ltd.

  5. Online differentiation of mineral phase in aerosol particles by ion formation mechanism using a LAAP-TOF single-particle mass spectrometer

    Science.gov (United States)

    Marsden, Nicholas A.; Flynn, Michael J.; Allan, James D.; Coe, Hugh

    2018-01-01

    Mineralogy of silicate mineral dust has a strong influence on climate and ecosystems due to variation in physiochemical properties that result from differences in composition and crystal structure (mineral phase). Traditional offline methods of analysing mineral phase are labour intensive and the temporal resolution of the data is much longer than many atmospheric processes. Single-particle mass spectrometry (SPMS) is an established technique for the online size-resolved measurement of particle composition by laser desorption ionisation (LDI) followed by time-of-flight mass spectrometry (TOF-MS). Although non-quantitative, the technique is able to identify the presence of silicate minerals in airborne dust particles from markers of alkali metals and silicate molecular ions in the mass spectra. However, the differentiation of mineral phase in silicate particles by traditional mass spectral peak area measurements is not possible. This is because instrument function and matrix effects in the ionisation process result in variations in instrument response that are greater than the differences in composition between common mineral phases.In this study, we introduce a novel technique that enables the differentiation of mineral phase in silicate mineral particles by ion formation mechanism measured from subtle changes in ion arrival times at the TOF-MS detector. Using a combination of peak area and peak centroid measurements, we show that the arrangement of the interstitial alkali metals in the crystal structure, an important property in silicate mineralogy, influences the ion arrival times of elemental and molecular ion species in the negative ion mass spectra. A classification scheme is presented that allowed for the differentiation of illite-smectite, kaolinite and feldspar minerals on a single-particle basis. Online analysis of mineral dust aerosol generated from clay mineral standards produced mineral fractions that are in agreement with bulk measurements reported by

  6. Online differentiation of mineral phase in aerosol particles by ion formation mechanism using a LAAP-TOF single-particle mass spectrometer

    Directory of Open Access Journals (Sweden)

    N. A. Marsden

    2018-01-01

    Full Text Available Mineralogy of silicate mineral dust has a strong influence on climate and ecosystems due to variation in physiochemical properties that result from differences in composition and crystal structure (mineral phase. Traditional offline methods of analysing mineral phase are labour intensive and the temporal resolution of the data is much longer than many atmospheric processes. Single-particle mass spectrometry (SPMS is an established technique for the online size-resolved measurement of particle composition by laser desorption ionisation (LDI followed by time-of-flight mass spectrometry (TOF-MS. Although non-quantitative, the technique is able to identify the presence of silicate minerals in airborne dust particles from markers of alkali metals and silicate molecular ions in the mass spectra. However, the differentiation of mineral phase in silicate particles by traditional mass spectral peak area measurements is not possible. This is because instrument function and matrix effects in the ionisation process result in variations in instrument response that are greater than the differences in composition between common mineral phases.In this study, we introduce a novel technique that enables the differentiation of mineral phase in silicate mineral particles by ion formation mechanism measured from subtle changes in ion arrival times at the TOF-MS detector. Using a combination of peak area and peak centroid measurements, we show that the arrangement of the interstitial alkali metals in the crystal structure, an important property in silicate mineralogy, influences the ion arrival times of elemental and molecular ion species in the negative ion mass spectra. A classification scheme is presented that allowed for the differentiation of illite–smectite, kaolinite and feldspar minerals on a single-particle basis. Online analysis of mineral dust aerosol generated from clay mineral standards produced mineral fractions that are in agreement with bulk

  7. Characterization of mineral phases of agricultural soil samples of Colombian coffee using Moessbauer spectroscopy and X-ray diffraction

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, Humberto Bustos, E-mail: hbustos@ut.edu.co; Lozano, Dagoberto Oyola; Martinez, Yebrayl Antonio Rojas; Pinilla, Marlene Rivera [Universidad del Tolima, Grupo Ciencia de Materiales y Tecnologia en Plasma (Colombia); Alcazar, German Antonio Perez [Universidad del Valle, Grupo Metalurgia Fisica y Teoria de las Transiciones de Fase (Colombia)

    2012-03-15

    Soil chemical analysis, X-ray diffraction (XRD) and Moessbauer spectrometry (MS) of {sup 57}Fe were used to characterize mineral phases of samples taken from the productive layer (horizon A) of agricultural coffee soil from Tolima (Colombia). Chemical analysis shows the chemical and textural parameters of samples from two different regions of Tolima, i.e., Ibague and Santa Isabel. By XRD phases like illite (I), andesine (A) and quartz (Q) in both samples were identified. The quantity of these phases is different for the two samples. The MS spectra taken at room temperature were adjusted by using five doublets, three of them associated to Fe{sup + 3} type sites and the other two to Fe{sup + 2} type sites. According to their isomer shift and quadrupole splitting the presence of phases like illite (detected by DRX), nontronite and biotite (not detected by XRD) can be postulated.

  8. Determination of soil weathering rates with U-Th series disequilibria: approach on bulk soil and selected mineral phases

    International Nuclear Information System (INIS)

    Gontier, Adrien

    2014-01-01

    The aim of the present study was to evaluate weathering and soil formation rates using U-Th disequilibria in bulk soil or separated minerals. The specific objectives of this work were to evaluate the use of U-Th chronometric tools 1) regarding the impact of a land cover change and the bedrock characteristics 2) in selected secondary mineral phases and 3) in primary minerals. On the Breuil-Chenue (Morvan) site, no vegetation effect neither a grain size effect was observed on the U-Th series in the deepest soil layers (≤ 40 cm). The low soil production rate (1-2 mm/ka) is therefore more affected by regional geomorphology than by the underlying bedrock texture. In the second part of this work, based on a thorough evaluation of different techniques, a procedure was retained to extract Fe-oxides without chemical fractionation. Finally, the analysis of biotites hand-picked from one of the studied soil profile showed that U-series disequilibria allow to independently determinate the field-weathering-rate of minerals. (author)

  9. PHASE ANALYSES OF URANIUM-BEARING MINERALS FROM THE HIGH GRADE ORE, NOPAL I, PENA BLANCA, MEXICO

    Energy Technology Data Exchange (ETDEWEB)

    M. Ren; P. Goodell; A. Kelts; E.Y. Anthony; M. Fayek; C. Fan; C. Beshears

    2005-07-11

    The Nopal I uranium deposit is located in the Pena Blanca district, approximately 40 miles north of Chihuahua City, Mexico. The deposit was formed by hydrothermal processes within the fracture zone of welded silicic volcanic tuff. The ages of volcanic formations are between 35 to 44 m.y. and there was secondary silicification of most of the formations. After the formation of at least part of the uranium deposit, the ore body was uplifted above the water table and is presently exposed at the surface. Detailed petrographic characterization, electron microprobe backscatter electron (BSE) imagery, and selected x-ray maps for the samples from Nopal I high-grade ore document different uranium phases in the ore. There are at least two stages of uranium precipitation. A small amount of uraninite is encapsulated in silica. Hexavalent uranium may also have been a primary precipitant. The uranium phases were precipitated along cleavages of feldspars, and along fractures in the tuff. Energy dispersive spectrometer data and x-ray maps suggest that the major uranium phases are uranophane and weeksite. Substitutions of Ca and K occur in both phases, implying that conditions were variable during the mineralization/alteration process, and that compositions of the original minerals have a major influence on later stage alteration. Continued study is needed to fully characterize uranium behavior in these semi-arid to arid conditions.

  10. X-ray-phase and IR-spectral study of clay rocks mineral content of the Caspian Sea Gulf depression

    International Nuclear Information System (INIS)

    Zakonov, A.N.; Mukhanova, M.U.

    2000-01-01

    Samples of clays selected from different oil fields (Sazankurak, Kemerkol, Kozha and others) and deposition depths are examined on both the X-ray diffractometers (Dron-2 and Dron-4) and the infrared-spectrometers (IR-20). In this diagnostic the American file with different minerals X-ray systematized data is used. The X-ray reflections, which are in compliance with suitable inter-plane distances and clay impurities reflex intensities are determined. With confirmation purpose for mineral content correctness obtained according X-ray-phase analysis the infrared-spectrometric method is used, in which principal attention was paid to absorption field (3,400-3,700 cm -1 ) of H 2 O and OH valency frequency vibrations

  11. The study of the sorption capacity of mineral kasongan and sand mixture of the waste of uranium organic phase

    International Nuclear Information System (INIS)

    Budiyono, M. E.; Sardjono, D.; Sukosrono

    1996-01-01

    An experimental investigation on the sorption capacity of mineral Kasongan and sand of Progo of the waste of uranium organic phase which to be connected with a backfill material which can be used to carried out of waste transportation from uncertain unit of the wastes to process of the wastes. The aim of the investigation wastes transportation must be conducted of the anticipation, that of the wastes with safe to unit management of wastes. Therefore must be investigated of the uranium organic wastes. This investigations which influence sorption ability, so an experimental investigation on its absorbability is necessary since this nuclide can not be dispersed to the environment. This investigation was carried out by varying some parameters which influence the sorption ability or sorptive capacity of the mineral Kasongan and the sand of Progo. The variables investigated were the grains size of the backfill material. Also the composition of mineral Kasongan/sand of Progo. The grains size were varied from 10-200 mesh and the composition were varied from 100/0 to 0/100 by weight. The sorption capacity of the maximum results was also determined. It can be concluded that the sorption capacity of the mineral Kasongan was the best at the grains of size about 80 mesh. The sorption capacity was 58 x 10 -2 ml/g and the grains size of the sand of Progo about 20 to 80 mesh was 30 x 10 -2 ml/g. The best sorption capacity of 58 x 10 -2 ml/g was gained at the composition of 100 % mineral Kasongan and 0% sand Progo. (author)

  12. How biological crusts are stabilizing the soil surface? The devolpment of organo-mineral interactions in the initial phase

    Science.gov (United States)

    Fischer, T.; Veste, M.; Wiehe, W.; Lange, P.

    2009-04-01

    First colonizers of new land surfaces are cryptogames which often form biological soil crusts (BSC) covering the first millimetre of the top soil in many ecosystems from polar to desert ecosystems. These BSC are assemblages of cyanobacteria, green algae, mosses, liverworts, fungi and/or lichens. The development of soil surface crusts plays a major role for the further vegetation pattern through changes to the physico-chemical conditions and influencing various ecosystem processes. We studied the development of BSC on quaternary substrate of an initial artificial water catchment in Lusatia, Germany. Due to lack of organic matter in the geological substrate, photoautotrophic organisms like green algae and cyanobacteria dominated the initial phases of ecosystem development and, hence, of organo-mineral ineractions. We combined SEM/EDX and FTIR microscopy to study the contact zone of extracellular polymeric substances (EPS) of green algae and cyanobacteria with quartz, spars and mica on a >40 µm scale in undisturbed biological soil crusts, which had a maximum thickness of approx. 2 mm. SEM/EDX microscopy was used to determine the spatial distribution of S, Ca, Fe, Al, Si and K in the profiles, organic compounds were identified using FTIR microscopy. Exudates of crust organisms served as cementing material between sand particles. The crust could be subdivided into two horizontal layers. The upper layer, which had a thickness of approx. 200 µm, is characterized by accumulation of Al and K, but absence of Fe in microbial derived organic matter, indicating capture of weathering products of feldspars and mica by microbial exudates. The pore space between mineral particles was entirely filled with organic matter here. The underlying layer can be characterized by empty pores and organo-mineral bridges between the sand particles. Contrarily to the upper layer of the crust, Fe, Al and Si were associated with organic matter here but K was absent. Highest similarity of the FTIR

  13. Immiscibility of Fluid Phases at Magmatic-hydrothermal Transition: Formation of Various PGE-sulfide Mineralization for Layered Basic Intrusions

    Science.gov (United States)

    Zhitova, L.; Borisenko, A.; Morgunov, K.; Zhukova, I.

    2007-12-01

    Fluid inclusions in quartz of the Merensky Reef (Bushveld Complex, South Africa) and the Chineisky Pluton (Transbaikal Region, Russia) were studied using cryometry, microthermometry, Raman-spectroscopy, LA ICP- MS, scanning electronic microscopy, gas-chromatography and isotopic methods. This allowed us to document some examples of fluid phase separation resulting in formation of different types of PGE-sulfide mineralization for layered basic intrusions. The results obtained show at least three generations of fluid separated from boiling residual alumosilicate intercumulus liquid of the Merensky Reef. The earliest fluid phase composed of homogenous high-dense methane and nitrogen gas mixture was identified in primary gas and co-existing anomalous fluid inclusions from symplectitic quartz. The next generation, heterophase fluid, composed of brines containing a free low-dense (mostly of carbon dioxide) gas phase, was observed in primary multiphase and coexisting gas-rich inclusions of miarolitic quartz crystals. The latest generation was also a heterophase fluid (low salinity water-salt solution and free low-dense methane gas phase) found in primary water-salt and syngenetic gas inclusions from peripheral zones of miarolitic quartz crystals. For the Chineisky Pluton reduced endocontact magmatogene fluids changed to oxidized low salinity hydrothermal fluids in exocontact zone. This resulted in formation of sulfide-PGE enrichment marginal zones of intrusion. The results obtained give us a possibility to suggest that: 1) Fluid phase separation is a typical feature of magmatogene fluids for layered basic intrusions. 2) Reduced fluids can extract and transport substantial PGE and sulfide concentrations. 3) Oxidation of reduced fluids is one of the most important geochemical barriers causing abundant PGE minerals and sulfides precipitation. This in turn results in both formation of PGE reefs or enriched contact zones of layered basic intrusions. This work was supported by

  14. INTER-PHASE CONTACTS IN BITUMEN-MINERAL SYSTEMS AND THEIR STRENGTHENING

    Directory of Open Access Journals (Sweden)

    Ya. N. Kovalev

    2014-01-01

    Full Text Available Presently bitumen-mineral materials (including asphalt-concrete comprise nearly 98 % for construction of expensive road pavement. Large resources of local minerals (quartz sand and industrial wastes in the form of used molding sand (foundry by-product are widely applied for reduction of their cost. Such approach is economically and ecologically reasonable but it requires its justification because an adhesion interaction in the bitumen-quartz substrate system (with SiO2 more than 95 % is rather poor in natural state and due to water action it is still more decreasing. In this connection an objective necessity arises to modify significantly technology of bitumen-mineral compositions for ensuring reliability of road pavements while using silicon components.All the ideas pertaining to strengthening of adhesion bonds in the “quartz mineral substrate - bitumen” system are traditionally of physical and chemical nature and they presuppose mainly usage of colloidal chemistry methods. The paper considers the matter on the basis of molecular kinetic theory of matter taking into account the fact that there is absence of generally accepted calculations for intermolecular interactions of components in the SiO2 - organic matrix material system.As a theoretical supposition the following well-known regulatory principle in physics is used: as every atom or molecular have its own electromagnetic field then action of external electromagnetic fields initiates their interaction that leads to excitement of electrons, deformations and rupture of chemical bonds. Literature analysis shows that the existing electric bonds between components of the SiO2 - organic matrix material system provide the possibility to apply various electro-physical methods having an effect on these components with the purpose to strengthen their adhesion interaction.The paper investigates matters for determination of bond energy during physical adsorption and adhesion in the SiO2 - organic

  15. Dynamics of mineral crystallization at inclusion-garnet interface from precipitated slab-derived fluid phase: first in-situ synchrotron x-ray measurements

    Science.gov (United States)

    Malaspina, Nadia; Alvaro, Matteo; Campione, Marcello; Nestola, Fabrizio

    2015-04-01

    Remnants of the fluid phase at ultrahigh pressure (UHP) in subduction environments may be preserved as primary multiphase inclusions in UHP minerals. These inclusions are frequently hosted by minerals stable at mantle depths, such as garnet, and show the same textural features as fluid inclusions. The mineral infillings of the solid multiphase inclusions are generally assumed to have crystallized by precipitation from the solute load of dense supercritical fluids equilibrating with the host rock. Notwithstanding the validity of this assumption, the mode of crystallization of daughter minerals during precipitation within the inclusion and/or the mechanism of interaction between the fluid at supercritical conditions and the host mineral are still poorly understood from a crystallographic point of view. A case study is represented by garnet orthopyroxenites from the Maowu Ultramafic Complex (China) deriving from harzburgite precursors metasomatised at ~ 4 GPa, 750 °C by a silica- and incompatible trace element-rich fluid phase. This metasomatism produced poikilitic orthopyroxene and inclusion-rich garnet porphyroblasts. Solid multiphase primary inclusions in garnet display a size within a few tens of micrometers and negative crystal shapes. Infilling minerals (spinel: 10-20 vol.%; amphibole, chlorite, talc, mica: 80- 90 vol.%) occur with constant volume ratios and derive from trapped solute-rich aqueous fluids. To constrain the possible mode of precipitation of daughter minerals, we performed for the first time a single-crystal X-ray diffraction experiment by means of Synchrotron Radiation at DLS-Diamond Light Source. In combination with electron probe microanalyses, this measurement allowed the unique identification of each mineral phase and their reciprocal orientations. We demonstrated the epitaxial relationship between spinel and garnet and between some hydrous minerals. Epitaxy drives a first-stage nucleation of spinel under near-to-equilibrium conditions

  16. Influence of composition of the raw materials on phase formation in solid compounds based on slag and clay minerals

    International Nuclear Information System (INIS)

    Galkin, A.V.; Tolebaev, T.; Omarova, V.I.; Burkitbaev, M.; Blynskiy, A.P.; Bachilova, N.V.; Matsynina, V.I.

    2003-01-01

    Full text: Activation of solidification processes in a compound formed on the basis of slag and clay minerals using sodium hydroxide - the output product from processing the BN-350 sodium coolant it is expedient to form the final product with a phase composition representing (in terms of long term storage) hydro-alumino-silicates incorporating Na-22 and Cs-137 radionuclides, which isomorphly replace other atoms in the crystal lattice sites. Combination of mineral phases, such as alkaline and alkaline-earth hydro-alumino-silicates with zeolite-like structure, providing sorptive properties, and the tobermorite like low-base hydro silicates of calcium defining the physico-mechanical properties of compound is the necessary condition for the compound stability. Investigations of phase formation in the mixtures of Kazakhstan clay, slag materials and alkali have been conducted targeted to control the physico-chemical properties of solid compound. The mixtures of alkali, thermal power plant ashes and clays of various mineralogical genesis (kaolinite, bentonite, Ca-Na-smectite montmorillonite) have been studied. The ashes and phosphorous slag while interacting with alkali are determined to form the non-alkaline hydro-silicates of stavrolite and indianite (anortite) type with free alkali being found in an unbound state. Both alkaline and alkaline-alkaline-earth hydro-silicates of Na 2 Ca 2 Si 2 O 7 H 2 O type are only formed in a compounds containing metallurgical slag. Formation of alkaline hydro-alumino-silicates of NaAlSiO 4 H 2 0 type as well as tomsonite (Na 4 Ca 8 [Al 20S i 20 O 80 ] 24H 2 O) - the zeolite like mineral have been detected in a two-component alkali-clay mixtures. Besides the quantity of tomsonite was determined to be not only dependent on Al 2 O 3 content in clay component but is also defined by stoichiometric composition of the mixture, because zeolite synthesis takes place under conditions of gels co-deposition and high pH value. Maximum quantity of

  17. Influence of particle size and mineral phase in the analysis of iron ore slurries by Laser-Induced Breakdown Spectroscopy

    International Nuclear Information System (INIS)

    Michaud, Daniel; Leclerc, Remi; Proulx, Eric

    2007-01-01

    Laser-Induced Breakdown Spectroscopy (LIBS) was applied to the analysis of iron ore concentrates. The objective was to determine the influence of particle size and mineral phase on the LIBS signal. The LIBS spectra of hematite and magnetite ore concentrates were qualitatively indistinguishable from each other but magnetite yielded systematically less than hematite. This behavior could be set into an empirical equation to correct the iron peak intensities according to the level of magnetite in the analyzed sample. Similarly, an increase of the LIBS signal was observed as the particle size of the ore samples decreased. Again, an equation could be written down to correct the intensity of either iron or silicon in response to a variation of the average particle size of the ore concentrate. Using these corrections, proper response of the silicon signal against the concentration of silica in the samples was restored. The observed dependence of the strength of the iron signal upon the mineral phase is attributed to oxidation of magnetite into hematite

  18. Design of the passive personal dosimeter for miners using an allyl diglycol carbonate plastic. Phase 1

    International Nuclear Information System (INIS)

    1983-12-01

    The report summarizes the results of the feasibility study on the design and development of a passive personal dosimeter incorporating an allyl diglycol carbonate plastic (CR39) detector, for use by uranium miners. Based upon the feasibility study, a passive personal dosimeter using a capacitor-type electrostatic enhancement device has been designed. Preliminary tests indicate that the prototype could be used in the mine environment to differentiate radon and thoron daughters with a detection efficiency comparable to that of a typical active device. Further study is required, however, into the possible influence in the mine environment of local variations in charged fraction, upon the calibration of this dosimeter

  19. Clay minerals in uraniferous deposit of Imouraren (Tim Mersoi basin, Niger): implications on genesis of deposit and on ore treatment process

    International Nuclear Information System (INIS)

    Billon, Sophie

    2014-01-01

    Nigerian uraniferous deposits are located in carboniferous and Jurassic formations of Tim Mersoi basin. AREVA is shareholder of 3 mine sites in this area: SOMAIR and COMINAK, both in exploitation since 1960's and IMOURAREN, 80 km further South, whose exploitation is planned for 2015. Mineralization of Imouraren deposit is included in the fluvial formation of Tchirezrine 2 (Jurassic), composed of channels and flood plains. Facies of channel in-fillings range from coarse sandstones to siltstones, while overflow facies are composed of analcimolites. Secondary mineralogy was acquired during 2 stages: 1- diagenesis, with formation of clay minerals, analcime, secondary quartz and albites, and 2- stage of fluids circulations, which induced alteration of detrital and diagenetic minerals, formation of new phases and uranium deposition. A mineralogical zoning, at the scale of deposit resulted from this alteration. The heterogeneity of Tchirezrine 2, at the level of both facies and mineralogy, is also evidenced during ore treatment, as ore reacts differently depending on its source, with sometimes problems of U recovery. Ore treatment tests showed that analcimes and chlorites were both penalizing minerals, because of 1- the sequestration of U-bearing minerals into analcimes, 2- their dissolution which trends to move away from U solubilization conditions (pH and Eh) and to form numerous sulfates, and 3- problems of percolation. A detection method of analcime-rich ores, based on infrared spectroscopy, was developed in order to optimize ore blending and so to reduce negative effects during ore treatment process. (author)

  20. The potential influence of Asian and African mineral dust on ice, mixed-phase and liquid water clouds

    Directory of Open Access Journals (Sweden)

    A. Wiacek

    2010-09-01

    Full Text Available This modelling study explores the availability of mineral dust particles as ice nuclei for interactions with ice, mixed-phase and liquid water clouds, also tracking the particles' history of cloud-processing. We performed 61 320 one-week forward trajectory calculations originating near the surface of major dust emitting regions in Africa and Asia using high-resolution meteorological analysis fields for the year 2007. Dust-bearing trajectories were assumed to be those coinciding with known dust emission seasons, without explicitly modelling dust emission and deposition processes. We found that dust emissions from Asian deserts lead to a higher potential for interactions with high ice clouds, despite being the climatologically much smaller dust emission source. This is due to Asian regions experiencing significantly more ascent than African regions, with strongest ascent in the Asian Taklimakan desert at ~25%, ~40% and 10% of trajectories ascending to 300 hPa in spring, summer and fall, respectively. The specific humidity at each trajectory's starting point was transported in a Lagrangian manner and relative humidities with respect to water and ice were calculated in 6-h steps downstream, allowing us to estimate the formation of liquid, mixed-phase and ice clouds. Downstream of the investigated dust sources, practically none of the simulated air parcels reached conditions of homogeneous ice nucleation (T≲−40 °C along trajectories that have not experienced water saturation first. By far the largest fraction of cloud forming trajectories entered conditions of mixed-phase clouds, where mineral dust will potentially exert the biggest influence. The majority of trajectories also passed through atmospheric regions supersaturated with respect to ice but subsaturated with respect to water, where so-called "warm ice clouds" (T≳−40 °C theoretically may form prior to supercooled water or mixed-phase clouds. The importance of "warm ice

  1. Carbon Mineralization by Aqueous Precipitation for Beneficial Use of CO2 from Flue Gas. Phase I. Final Topical Report

    International Nuclear Information System (INIS)

    Constantz, Brent; Seeker, Randy; Devenney, Martin

    2010-01-01

    Calera's innovative Mineralization via Aqueous Precipitation (MAP) technology for the capture and conversion of CO 2 to useful materials for use in the built environment was further developed and proven in the Phase 1 Department of Energy Grant. The process was scaled to 300 gallon batch reactors and subsequently to Pilot Plant scale for the continuous production of product with the production of reactive calcium carbonate material that was evaluated as a supplementary cementitious material (SCM). The Calera SCM(trademark) was evaluated as a 20% replacement for ordinary portland cement and demonstrated to meet the industry specification ASTM 1157 which is a standard performance specification for hydraulic cement. The performance of the 20% replacement material was comparable to the 100% ordinary portland cement control in terms of compressive strength and workability as measured by a variety of ASTM standard tests. In addition to the performance metrics, detailed characterization of the Calera SCM was performed using advanced analytical techniques to better understand the material interaction with the phases of ordinary portland cement. X-ray synchrotron diffraction studies at the Advanced Photon Source in Argonne National Lab confirmed the presence of an amorphous phase(s) in addition to the crystalline calcium carbonate phases in the reactive carbonate material. The presence of carboaluminate phases as a result of the interaction of the reactive carbonate materials with ordinary portland cement was also confirmed. A Life Cycle Assessment was completed for several cases based on different Calera process configurations and compared against the life cycle of ordinary portland cement. In addition to the materials development efforts, the Calera technology for the production of product using an innovative building materials demonstration plant was developed beyond conceptual engineering to a detailed design with a construction schedule and cost estimate.

  2. Retention of actinide and fission products by poly-mineral solid phases

    International Nuclear Information System (INIS)

    Peynet, Vincent

    2003-01-01

    This research thesis first reports available knowledge on reactivity of mineral surfaces (notably the thermodynamic modelling of their retention properties) and discusses the different approaches proposed in the literature regarding the prediction of retention of an element on an adsorbent mixing. It also proposes a synthesis of publications on retention properties of montmorillonite, goethite and calcite with respect to elements with high or very low concentrations. Then, the author reports a characterization of solids in terms of ion exchanger theory. Results are used for traces of caesium, americium and selenium. He finally reports measurement results of traces of elements by montmorillonite / goethite and montmorillonite / calcite binary mixings, or by montmorillonite / goethite / calcite ternary mixings

  3. Multiscale characterization of the mineral phase at skeletal sites of breast cancer metastasis

    Science.gov (United States)

    Chiou, Aaron E.; Loh, Hyun Chae; Lynch, Maureen; Seo, Bo Ri; Song, Young Hye; Hoerth, Rebecca; Bortel, Emely L.; Willie, Bettina M.; Duda, Georg N.; Masic, Admir; Wagermaier, Wolfgang; Fratzl, Peter; Fischbach, Claudia

    2017-01-01

    Skeletal metastases, the leading cause of death in advanced breast cancer patients, depend on tumor cell interactions with the mineralized bone extracellular matrix. Bone mineral is largely composed of hydroxyapatite (HA) nanocrystals with physicochemical properties that vary significantly by anatomical location, age, and pathology. However, it remains unclear whether bone regions typically targeted by metastatic breast cancer feature distinct HA materials properties. Here we combined high-resolution X-ray scattering analysis with large-area Raman imaging, backscattered electron microscopy, histopathology, and microcomputed tomography to characterize HA in mouse models of advanced breast cancer in relevant skeletal locations. The proximal tibial metaphysis served as a common metastatic site in our studies; we identified that in disease-free bones this skeletal region contained smaller and less-oriented HA nanocrystals relative to ones that constitute the diaphysis. We further observed that osteolytic bone metastasis led to a decrease in HA nanocrystal size and perfection in remnant metaphyseal trabecular bone. Interestingly, in a model of localized breast cancer, metaphyseal HA nanocrystals were also smaller and less perfect than in corresponding bone in disease-free controls. Collectively, these results suggest that skeletal sites prone to tumor cell dissemination contain less-mature HA (i.e., smaller, less-perfect, and less-oriented crystals) and that primary tumors can further increase HA immaturity even before secondary tumor formation, mimicking alterations present during tibial metastasis. Engineered tumor models recapitulating these spatiotemporal dynamics will permit assessing the functional relevance of the detected changes to the progression and treatment of breast cancer bone metastasis. PMID:28923958

  4. Platinum-Group Minerals and Other Accessory Phases in Chromite Deposits of the Alapaevsk Ophiolite, Central Urals, Russia

    Directory of Open Access Journals (Sweden)

    Federica Zaccarini

    2016-10-01

    Full Text Available An electron microprobe study has been carried out on platinum-group minerals, accessory phases, and chromite in several chromite deposits of the Alapaevsk ophiolite (Central Urals, Russia namely the Bakanov Kluch, Kurmanovskoe, Lesnoe, 3-d Podyony Rudnik, Bol’shaya Kruglyshka, and Krest deposits. These deposits occur in partially to totally serpentinized peridotites. The microprobe data shows that the chromite composition varies from Cr-rich to Al-rich. Tiny platinum-group minerals (PGM, 1–10 µm in size, have been found in the chromitites. The most abundant PGM is laurite, accompanied by minor cuproiridsite and alloys in the system Os–Ir–Ru. A small grain (about 20 μm was found in the interstitial serpentine of the Bakanov Kluch chromitite, and its calculated stoichiometry corresponds to (Ni,Fe5P. Olivine, occurring in the silicate matrix or included in fresh chromite, has a mantle-compatible composition in terms of major and minor elements. Several inclusions of amphibole, Na-rich phlogopite, and clinopyroxene have been identified. The bimodal Cr–Al composition of chromite probably corresponds to a vertical distribution in the ophiolite sequence, implying formation of Cr-rich chromitites in the deep mantle, and Al-rich chromitites close to the Moho-transition zone, in a supra-subduction setting. The presence of abundant hydrous silicate inclusions, such as amphibole and phlogopite, suggests that the Alapaevsk chromitites crystallized as a result of the interaction between a melt enriched in fluids and peridotites. Laurite and cuproiridsite are considered to be magmatic in origin, i.e., entrapped as solid phases during the crystallization of chromite at high temperatures. The sulfur fugacity was relatively high to allow the precipitation of Ir-bearing sulfides, but below the Os–OsS2 buffer. The alloys in the system Os–Ir–Ru are classified as secondary PGM, i.e., formed at low temperature during the serpentinization process. The

  5. The effect of soil mineral phases on the abiotic degradation of selected organic compounds. Final report, June 31, 1990--December 31, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Sandhu, S.S.

    1994-12-31

    Funds were received from the United States Department of Energy to study the effects of soil mineral phases on the rates of abiotic degradation of tetraphenylborate (TPB) and diphenylboronic acid (DPBA). In addition to kaolinite and montmorillonite clay minerals, the role of goethite, corundum, manganite, and rutile in the degradation of organoborates was also evaluated. The effects of DPBA, argon, molecular dioxygen (O{sub 2}), temperature, and organic matter on the degradation of organoborates were also measured. The results indicated that TPB and DPBA degraded rapidly on the mineral surfaces. The initial products generated from the degradation of TPB were DPBA and biphenyl; however, further degradation resulted in the formation of phenylboric acid and phenol which persisted even after TPB disappeared. The data also showed that the rate of TPB degradation was faster in kaolinite, a 1:1 clay mineral, than in montmorillonite, a double layer mineral. The initial degradation of TPB by corundum was much higher than goethite, manganite and rutile. However, no further degradation by this mineral was observed where as the degradation of TPB continued by goethite and rutile minerals. Over all, the degradation rate of TPB was the highest for goethite as compared to the other metal oxide minerals. The degradation of TPB and DPBA was a redox reaction where metals (Fe, Al, Ti, Mn) acted as Lewis acids. DPBA and argon retarded the TPB degradation where as molecular oxygen organic matter and temperature increased the rate of TPB disappearance.

  6. Nuclear techniques and cross-correlation methods for spectral analysis in two-phase flow measurements in mineral pipelines

    Energy Technology Data Exchange (ETDEWEB)

    Brandao, Luis E.B.; Salgado, Cesar M., E-mail: brandaos@ien.gov.br, E-mail: otero@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil). Divisao de Radiofarmacos; Sicilliano, Umberto C.C.S., E-mail: umberto.cassara@poli.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Dept. de Metalurgia

    2013-07-01

    In mineral industry is common to use water to transport pellets inside pipes. In these units, the correct measurement of flow (both solid and liquid phase) is important to guarantee a safe operation. Cross correlation flow meters are devices specially suited to be used in dual-phase flow and they are based on measure the transit time due the disturbances registered between two points, in our case gamma attenuation from radioactive sources. The emphasis of this work is the application of gamma transmission and scattering technique associated with spectral analysis methods to measure the flow of solid phase in a liquid fluid in side the pipe. The detectors and the sources are out side of the tube and are positioned 10.0 cm distant one from the other. The photons of transmission/scattering gamma radiation were registered, and across-correlation method was applied to measure the flow and spectral analysis was used to study the flow profile inside the pipe. (author)

  7. Techniques of sample attack used in soil and mineral analysis. Phase I

    International Nuclear Information System (INIS)

    Chiu, N.W.; Dean, J.R.; Sill, C.W.

    1984-07-01

    Several techniques of sample attack for the determination of radioisotopes are reviewed. These techniques include: 1) digestion with nitric or hydrochloric acid in Parr digestion bomb, 2) digestion with a mixture of nitric and hydrochloric acids, 3) digestion with a mixture of hydrofluoric, nitric and perchloric acids, and 4) fusion with sodium carbonate, potassium fluoride or alkali pyrosulfates. The effectiveness of these techniques to decompose various soils and minerals containing radioisotopes such as lead-210 uranium, thorium and radium-226 are discussed. The combined procedure of potassium fluoride fusion followed by alkali pyrosulfate fusion is recommended for radium-226, uranium and thorium analysis. This technique guarantees the complete dissolution of samples containing refractory materials such as silica, silicates, carbides, oxides and sulfates. For the lead-210 analysis, the procedure of digestion with a mixture of hydrofluoric, nitric and perchloric acids followed by fusion with alkali pyrosulfate is recommended. These two procedures are detailed. Schemes for the sequential separation of the radioisotopes from a dissolved sample solution are outlined. Procedures for radiochemical analysis are suggested

  8. The effects of the mineral phase on C stabilization mechanisms and the microbial community along an eroding slope transect

    Science.gov (United States)

    Doetterl, S.; Opfergelt, S.; Cornelis, J.; Boeckx, P. F.; van oost, K.; Six, J.

    2013-12-01

    An increasing number of studies show the importance of including soil redistribution processes in understanding carbon (C) dynamics in eroding landscapes. The quality and quantity of soil organic carbon in sloping cropland differs with topographic position. These differences are commonly more visible in the subsoil, while the size and composition of topsoil C pools are similar along the hillslope. The type (plant- or microbial-derived) and quality (level of degradation) of C found in a specific soil fraction depends on the interplay between the temporal dynamic of the specific mechanism and it's strength to protect C from decomposition. Here, we present an analysis that aims to clarify the bio/geo-chemical and mineralogical components involved in stabilizing C at various depths and slope positions and how they affect the microbial community and the degradation of C. For this we analyzed soil samples from different soil depths along a slope transect applying (i) a sequential extraction of the reactive soil phase using pyrophosphate, oxalate and dithionite-citrate-bicarbonate, (ii) a semi-quantitative and qualitative analysis of the clay mineralogy, (iii) an analysis of the microbial community using amino sugars and (iv) an analysis of the level of degradation of C in different soil fractions focusing on the soil Lignin signature. The results show that the pattern of minerals and their relative importance in stabilizing C varies greatly along the transect. In the investigated soils, pyrophosphate extractable Manganese, and not Iron or Aluminum as often observed, is strongly correlated to C in the bulk soil and in the non-aggregated silt and clay fractions. This suggests a certain role of Manganese for C stabilization where physical protection is absent. In contrast, pyrophosphate extractable Iron and Aluminum components are largely abundant in water-stable soil aggregates but not correlated to C, suggesting importance of these extracts to stabilize aggregates and

  9. Differential chemical fractionation of dissolved organic matter during sorption by Fe mineral phases in a tropical soil from the Luquillo Critical Zone Observatory

    Science.gov (United States)

    Plante, A. F.; Coward, E.; Ohno, T.; Thompson, A.

    2017-12-01

    Fe-bearing mineral phases contribute substantially to adsorption and stabilization of soil organic matter (SOM), due largely to their high specific surface area (SSA) and reactivity. While the importance of adsorption onto mineral surfaces has been well-elucidated, selectivity of various mineral and organic phases remains poorly understood. The goals of this work were to: 1) quantify the contributions of Fe-minerals of varying crystallinity to dissolved organic matter (DOM) sorption, and 2) characterize the molecular fractionation of DOM induced by reactions at the mineral interface, using a highly-weathered Oxisol from the Luquillo Critical Zone Observatory (LCZO). Three selective dissolution experiments targeting Fe-mineral phases were followed by specific surface area (SSA) analysis of the residues and characterization of extracted DOM by high resolution mass spectrometry (FT-ICR-MS). Fe-depleted extraction residue samples, untreated control soil samples, and Fe-enriched ferrihydrite-coated soil samples were then subjected to a batch sorption experiment with litter-derived DOM. Results of selective dissolution experiments indicated that a substantial proportion of soil SSA was derived from extracted Fe-bearing phases, and FT-ICR-MS analysis of extracted DOM revealed distinct chemical signatures. Sorbed C concentrations were well correlated with Fe contents induced by treatments, and thus SSA. Molecular characterization of the DOM post-sorption indicated that poorly crystalline Fe phases preferentially adsorbed highly unsaturated aromatic compounds, and higher-crystallinity Fe phases were associated with more aliphatic compounds. These findings suggests that molecular fractionation via organomineral complexation may act as a physicochemical filter of DOM released to the critical zone.

  10. Structural effects of C60+ bombardment on various natural mineral samples-Application to analysis of organic phases in geological samples

    International Nuclear Information System (INIS)

    Siljestroem, S.; Lausmaa, J.; Hode, T.; Sundin, M.; Sjoevall, P.

    2011-01-01

    Organic phases trapped inside natural mineral samples are of considerable interest in astrobiology, geochemistry and geobiology. Examples of such organic phases are microfossils, kerogen and oil. Information about these phases is usually retrieved through bulk crushing of the rock which means both a risk of contamination and that the composition and spatial distribution of the organics to its host mineral is lost. An attractive of way to retrieve information about the organics in the rock is depth profiling using a focused ion beam. Recently, it was shown that it is possible to obtain detailed mass spectrometric information from oil-bearing fluid inclusions, i.e. small amounts of oil trapped inside a mineral matrix, using ToF-SIMS. Using a 10 keV C 60 + sputter beam and a 25 keV Bi 3 + analysis beam, oil-bearing inclusions in different minerals were opened and analysed individually. However, sputtering with a C 60 + beam also induced other changes to the mineral surface, such as formation of topographic features and carbon deposition. In this paper, the cause of these changes is explored and the consequences of the sputter-induced features on the analysis of organic phases in natural mineral samples (quartz, calcite and fluorite) in general and fluid inclusions in particular are discussed. The dominating topographical features that were observed when a several micrometers deep crater is sputtered with 10 keV C 60 + ions on a natural mineral surface are conical-shaped and ridge-like structures that may rise several micrometers, pointing in the direction of the incident C 60 + ion beam, on an otherwise flat crater bottom. The sputter-induced structures were found to appear at places with different chemistry than the host mineral, including other minerals phases and fluid inclusions, while structural defects in the host material, such as polishing marks or scratches, did not necessarily result in sputter-induced structures. The ridge-like structures were often covered

  11. In Situ Chemical Characterization of Mineral Phases in Lunar Granulite Meteorite Northwest Africa 5744

    Science.gov (United States)

    Kent, J. J.; Brandon, A. D.; Lapen, T. J.; Peslier, A. H.; Irving, A. J.; Coleff, D. M.

    2012-01-01

    Northwest Africa (NWA) 5744 meteorite is a granulitic and troctolitic lunar breccia which may represent nearly pristine lunar crust (Fig. 1). NWA 5744 is unusually magnesian compared to other lunar breccias, with bulk [Mg/(Mg+Fe)] 0.79 [1, 2]. Inspection shows impactor content is likely to be very minor, with low Ni content and a lack of metal grains. Some terrestrial contamination is present, evidenced by calcite within cracks. NWA 5744 has notably low concentrations of incompatible trace elements (ITEs) [2]. The goal of this study is to attempt to classify this lunar granulite through analyses of in situ phases.

  12. Fe2+ oxidation rate drastically affect the formation and phase of secondary iron hydroxysulfate mineral occurred in acid mine drainage

    International Nuclear Information System (INIS)

    Huang Shan; Zhou Lixiang

    2012-01-01

    During the processes of secondary iron hydroxysulfate mineral formation, Fe 2+ ion was oxidized by the following three methods: (1) biooxidation treatment by Acidithiobacillus ferrooxidans (A. ferrooxidans); (2) rapid abiotic oxidation of Fe 2+ with H 2 O 2 (rapid oxidation treatment); (3) slow abiotic oxidation of Fe 2+ with H 2 O 2 (slow oxidation treatment). X-ray diffraction (XRD) patterns, element composition, precipitate weight and total Fe removal efficiency were analyzed. The XRD patterns and element composition of precipitates synthesized through the biooxidation and the slow oxidation treatments well coincide with those of potassium jarosite, while precipitates formed at the initial stage of incubation in the rapid oxidation treatment showed a similar XRD pattern to schwertmannite. With the ongoing incubation, XRD patterns and element composition of the precipitates that occurred in the rapid oxidation treatment were gradually close to those in the biooxidation and the slow oxidation treatments. Due to the inhibition of A. ferrooxidans itself and its extracellular polymeric substances (EPS) in aggregation of precipitates, the amount of precipitates and soluble Fe removal efficiency were lower in the biooxidation treatment than in the slow oxidation treatment. Therefore, it is concluded that Fe 2+ oxidation rate can greatly affect the mineral phase of precipitates, and slow oxidation of Fe 2+ is helpful in improving jarosite formation. - Highlights: ► Slow oxidation of Fe 2+ is helpful in jarosite formation. ► The already-formed schwertmannite can be gradually transformed to jarosite. ► Precipitates formation can be inhibited probably by EPS from A. ferrooxidans.

  13. Effects on auto-irradiation on the solubility of mineral phases enriched by actinides

    International Nuclear Information System (INIS)

    Prot, T.

    1993-07-01

    The scope of the present work is to investigate possible effects of self-irradiation damage induced by α-decay (α-recoil nucleus and α-particle) on the hydrated layer formed by aqueous corrosion of nuclear glass and on alteration phases of a granitic geological repository (calcium carbonate or iron oxides and oxihydroxide) which would be likely irradiated in the framework of high-level radioactive waste disposal, for sufficient concentration of actinides and age. Our experimental procedure relies on a bombardment with external beams of 1.5 to 1.8 MeV He ions and 200 KeV Pb ions, which respectively simulate the radiation effects of α-particles and of α-recoil nuclei. We have observed in a first step, direct irradiation effects (change of volume and refractive index, chemical modification) by means of optical microscopy, microtopographical analysis (surface profilometer) and R.B.S. and X.P.S. In a second step, corrosion tests were performed in static conditions to observe a possible indirect effect (increase of the hydratation rate, actinide release) on the later evolution as for example, a marked increase in solubility (calcium carbonate case)

  14. A fase estrogênica altera a resposta do osso e do metabolismo mineral de ratas com hipertireoidismo? Does the estrogenic phase modify the bone and mineral metabolism response in rats under hyperthyroidism?

    Directory of Open Access Journals (Sweden)

    N.M. Ocarino

    2003-08-01

    Full Text Available The effect of the estrogenic phase in the bone and in the mineral metabolism was studied in Wistar adult female rats kept under euthyroidism or hyperthyroidism for 60 days. The rats were divided, according to the stage of the estrous cycle, into four groups: 1 euthyroid (proestrus-estrus, 2 euthyroid (metaestrus-diestrus, 3 hyperthyroid (proestrus-estrus, and 4 hyperthyroid (metaestrus-diestrus. After 60 days the blood plasma was collected and the concentrations of free T4, estradiol, progesterone, calcium, phosphorus, and of alkaline phosphatase were determined. The bones (femur and tibia were analysed microscopically. Despite of the functional state of the thyroid, the levels of estrogen were significantly higher in the proestrus-estrus. The estrogenic phase increased the plasmatic concentration of calcium significantly in the euthyroid rats but it did not alter the levels of phosphorus and alkaline phosphatase. In the hyperthyroid state no significant differences in the plasmatic concentrations of calcium, phosphorus and alkaline phosphatase throughout the cycle were found. The phases of the cycle did not also influence the bone morphology in the euthyroid and hyperthyroid states. It was concluded that the estrogenic phase increases the plasmatic concentration of calcium, even without altering the bone morphology of the euthyroid rats. In addition the estrogenic phase does not increase the plasmatic calcium and it does not modify the response of the bone as well as of the mineral metabolism under effect of the hyperthyroidism.

  15. Bioleaching of vanadium from barren stone coal and its effect on the transition of vanadium speciation and mineral phase

    Science.gov (United States)

    Wang, Xin; Lin, Hai; Dong, Ying-bo; Li, Gan-yu

    2018-03-01

    This study determined the optimal conditions required to obtain maximum vanadium extraction and examined the transition of mineral phases and vanadium speciation during the bioleaching process. Parameters including the initial pH value, initial Fe2+ concentration, solid load, and inoculum quantity were examined. The results revealed that 48.92wt% of the vanadium was extracted through bioleaching under optimal conditions. Comparatively, the chemical leaching yield (H2SO4, pH 2.0) showed a slower and milder increase in vanadium yield. The vanadium bioleaching yield was 35.11wt% greater than the chemical leaching yield. The Community Bureau of Reference (BCR) sequential extraction results revealed that 88.62wt% of vanadium existed in the residual fraction. The bacteria substantially changed the distribution of the vanadium speciation during the leaching process, and the residual fraction decreased to 48.44wt%. The X-ray diffraction (XRD) and Fourier transform infrared (FTIR) results provided evidence that the crystal lattice structure of muscovite was destroyed by the bacteria.

  16. Enhanced performance and interfacial investigation of mineral-based composite phase change materials for thermal energy storage.

    Science.gov (United States)

    Li, Chuanchang; Fu, Liangjie; Ouyang, Jing; Yang, Huaming

    2013-01-01

    A novel mineral-based composite phase change materials (PCMs) was prepared via vacuum impregnation method assisted with microwave-acid treatment of the graphite (G) and bentonite (B) mixture. Graphite and microwave-acid treated bentonite mixture (GBm) had more loading capacity and higher crystallinity of stearic acid (SA) in the SA/GBm composite. The SA/GBm composite showed an enhanced thermal storage capacity, latent heats for melting and freezing (84.64 and 84.14 J/g) was higher than those of SA/B sample (48.43 and 47.13 J/g, respectively). Addition of graphite was beneficial to the enhancement in thermal conductivity of the SA/GBm composite, which could reach 0.77 W/m K, 31% higher than SA/B and 196% than pure SA. Furthermore, atomic-level interfaces between SA and support surfaces were depicted, and the mechanism of enhanced thermal storage properties was in detail investigated.

  17. Mineral Phases and Release Behaviors of As in the Process of Sintering Residues Containing As at High Temperature

    Directory of Open Access Journals (Sweden)

    Xingrun Wang

    2014-01-01

    Full Text Available To investigate the effect of sintering temperature and sintering time on arsenic volatility and arsenic leaching in the sinter, we carried out experimental works and studied the structural changes of mineral phases and microstructure observation of the sinter at different sintering temperatures. Raw materials were shaped under the pressure of 10 MPa and sintered at 1000~1350°C for 45 min with air flow rate of 2000 mL/min. The results showed that different sintering temperatures and different sintering times had little impact on the volatilization of arsenic, and the arsenic fixed rate remained above 90%; however, both factors greatly influenced the leaching concentration of arsenic. Considering the product’s environmental safety, the best sintering temperature was 1200°C and the best sintering time was 45 min. When sintering temperature was lower than 1000°C, FeAsS was oxidized into calcium, aluminum, and iron arsenide, mainly Ca3(AsO42 and AlAsO4, and the arsenic leaching was high. When it increased to 1200°C, arsenic was surrounded by a glass matrix and became chemically bonded inside the matrix, which lead to significantly lower arsenic leaching.

  18. Microbial Mineral Transformations at the Fe(II)/Fe(III) Redox Boundary for Solid Phase Capture of Strontium and Other Metal/Radionuclide Contaminants

    International Nuclear Information System (INIS)

    Ferris, F.G.; Roden, E.E.

    2000-01-01

    The migration of 90 Sr in groundwater is a significant environmental concern at former nuclear weapons production sites in the US and abroad. Although retardation of 90 Sr transport relative to mean groundwater velocity is known to occur in contaminated aquifers, Sr 2+ does not sorb as strongly to iron oxides and other mineral phases as do other metal-radionuclides contaminants. Thus, some potential exists for extensive 90 Sr migration from sources of contamination. Chemical or biological processes capable of retarding or immobilizing Sr 2+ in groundwater environments are of interest from the standpoint of understanding controls on subsurface Sr 2+ migration. In addition, it may be possible to exploit such processes for remediation of subsurface Sr contamination. In this study the authors examined the potential for the solid phase sorption and incorporation of Sr 2+ into carbonate minerals formed during microbial Fe(III) oxide reduction as a first step toward evaluating whether this process could be used to promote retardation of 90 Sr migrations in anaerobic subsurface environments. The demonstration of Sr 2+ capture in carbonate mineral phases formed during bacterial HFO reduction and urea hydrolysis suggests that microbial carbonate mineral formation could contribute to Sr 2+ retardation in groundwater environments. This process may also provide a mechanism for subsurface remediation of Sr 2+ and other divalent metal contaminants that form insoluble carbonate precipitates

  19. The influence of mineralization on the phase composition and properties of low-burned clay-dolomited composition materials

    International Nuclear Information System (INIS)

    Shirin-zade, I.N.; Ganbarov, D.M.

    2008-01-01

    With aim of acceleration of dissociation of carbonates in clay-dolomited compositions Na 2 SiF 6 was added. Addition mineralization raise stability of composition reaches 20-30 MPa. Na 2 SiF 6 mineralization makes more active decomposition of dolomite and accelerate appearance of new creations. It was experimentally proved that adding of mineralization of Na 2 SiF 6 promote to appearance in mixture of intermediate double salts which are bring down temperature of dissociation of carbonates. Accelerated action of mineralization Na 2 SiF 6 accepted by x-ray, DTA and x-ray spectroscopy

  20. Towards sustainable processing of columbite group minerals: elucidating the relation between dielectric properties and physico-chemical transformations in the mineral phase.

    Science.gov (United States)

    Sanchez-Segado, Sergio; Monti, Tamara; Katrib, Juliano; Kingman, Samuel; Dodds, Chris; Jha, Animesh

    2017-12-21

    Current methodologies for the extraction of tantalum and niobium pose a serious threat to human beings and the environment due to the use of hydrofluoric acid (HF). Niobium and tantalum metal powders and pentoxides are widely used for energy efficient devices and components. However, the current processing methods for niobium and tantalum metals and oxides are energy inefficient. This dichotomy between materials use for energy applications and their inefficient processing is the main motivation for exploring a new methodology for the extraction of these two oxides, investigating the microwave absorption properties of the reaction products formed during the alkali roasting of niobium-tantalum bearing minerals with sodium bicarbonate. The experimental findings from dielectric measurement at elevated temperatures demonstrate an exponential increase in the values of the dielectric properties as a result of the formation of NaNbO 3 -NaTaO 3 solid solutions at temperatures above 700 °C. The investigation of the evolution of the dielectric properties during the roasting reaction is a key feature in underpinning the mechanism for designing a new microwave assisted high-temperature process for the selective separation of niobium and tantalum oxides from the remainder mineral crystalline lattice.

  1. The mineral phase evolution behaviour in the production of glass-ceramics from municipal solid waste incineration fly ash by melting technology.

    Science.gov (United States)

    Luan, Jingde; Chai, Meiyun; Li, Rundong; Yao, Pengfei; Khan, Agha Saood

    2016-01-01

    High energy consumption was the major obstacle to the widespread application of melting technology in the treatment of municipal solid waste incineration fly ash. Aiming to lower the ash-melting temperature (AMT) for energy-saving, differential scanning calorimetry, X-ray diffraction and the scanning electron microscope were used to investigate the relations between AMT and the mineral evolution. The results indicated that the change of AMT was determined by the types and the contents of mineral crystals. The transition from refractory minerals to fluxing minerals was the key. The transition of the main crystalline phase from pseudowollastonite (Ca3(Si3O9)) to wollastonite (CaSiO3) played a significant role in AMT reduction. A quantum chemistry calculation was carried out to investigate the effect of crystal reaction activity on AMT. In the chemical reaction, the highest occupied molecular orbital and the lowest unoccupied molecular orbital played a more important role than any other orbits. Cations (Ca(2+), Mg(2+), Na(+), K(+)) were apt to enter into the crystal lattice of wollastonite and gehlenite mainly through Si (3), O (1), Si (6), O (10) and Al (2), O (10), and broke the covalent bonds of Si (3)-O (7), Al (1)-O (9) and Al (1)-O (15), respectively. This deconstruction behaviour provided convenient conditions for restructuring and promoted the formation of fluxing minerals. In melts, the excess SiO2 monomers which existed in the form of cristobalite and quartz caused AMT increase.

  2. Mineral CO2 sequestration in basalts and ultra-basic rocks: impact of secondary silicated phases on the carbonation process

    International Nuclear Information System (INIS)

    Sissmann, Olivier

    2013-01-01

    The formation of carbonates constitutes a stable option for carbon dioxide (CO 2 ) geological sequestration, and is prone to play a significant role in reducing emissions of anthropic origin. However, our comprehension of the carbonation mechanism, as well as of the kinetics limitations encountered during this chemical reaction, remains poorly developed. Though there is a large number of studies focusing on the dissolution kinetics of basic silicates and on the precipitation of carbonates, few have inquired about the impact that the formation of non-carbonated secondary phases can have on these reaction's kinetics. It is the approach chosen here, as only solid knowledge of the global carbonation mechanism can make this process predictive and efficient. Experimental data on dissolution and carbonation have therefore been determined in batch reactors, on relevant minerals and rocks. Firstly, we studied the carbonation of olivine (a major phase within peridotites and minor within basalts) at 90 deg. C and under pCO 2 of 280 bars. The dissolution of San Carlos olivine (Mg 1.76 Fe 0.24 SiO 4 ) is slowed down by the formation of a surface silica gel, when the fluid reaches equilibrium with amorphous silica. The transport of species to the reactive medium becomes the limiting step of the process, slowing down the dissolution process of San Carlos olivine by 5 orders of magnitude. However, this passivation doesn't occur during the alteration of Ca-olivine (Ca 2 SiO 4 ), though a surface silica layer does form. This comparison suggests that it isn't the structure of the silicate but its chemical composition, which controls the transport properties through the interfacial layer. The second part explores the effects of organic ligands and of temperature variations on the formation of those phases. The addition of citrate at 90 deg. C increases the kinetics of San Carlos olivine by one order of magnitude, and allows the release of enough Mg in the aqueous medium to form

  3. Detection of rare-earth-mineral phases by scanning electron microscopy/energy dispersive x-rays (SEM/EDX) in the alkaline complexes of Tamil Nadu

    International Nuclear Information System (INIS)

    Sengupta, S.K.; Nathan, N.P.; Ganesan, V.; Shome, S.

    2005-01-01

    The alkaline complexes of the Southern Granulite Terrain (SGT) are generally restricted within NNW-SSE-trending Dharmapuri Shear Zone (DSZ), extending from Gudiyatham in the north and Bhavani in the south in Tamil Nadu. REE-rich phases have been studied under EDX (Energy Dispersive X-rays) from the different alkaline suites of Tamil Nadu. In Elagiri, the Th-rich epidote/allanite is concentrically zoned and occurs in the outermost coarse sub-solvus syenite, indicating that the REE concentration is restricted within the late-stage magmatic activity. In Koratti, the apatites are LREE rich. In Samalpatti Complex, the carbonatites host a number of REE-rich minerals commonly classified as betafite, along with nioborutite and nioboilmenite. The niobo-rutile and niobo-ilmenite show exsolved texture. The betafite is zoned with mendelyeerite. Some of the molybdenite in Samalpatti is dendritic indicating incomplete crystallisation. In Sivamalai, the REE phases are generally associated with ferrosyenite and nepheline syenite as adsorbed grains around apatite or carbonate. The REE minerals are Zr-REE titanate, REE-titano silicate and REE-yttrium silicate. In the Pikkili Complex, the REE minerals generally occur as rim around apatite and calcite. A discrete metamict allanite grain with radial cracks occurs within syenite. In Pakkanadu Complex zoned allanite occurs with distinct chemical zonation in syenite. Monazite and celesto-barite are associated with barite suggesting that the REE phases are developed in the late intrusive stage. (author)

  4. Fissure minerals, literature review

    International Nuclear Information System (INIS)

    Larsson, S.Aa.

    1980-01-01

    This paper is a review of methods used for direct and indirect dating of tectonic events. Isotope geochemistry including stable isotopes as well as fission track- dating, fluid inclusion and thermoluminescens techniques have been considered. It has been concluded that an investigation of tectonic (and thermal) events should start with a detailed study of the mineral phases grown in seald fissures as well as minerals from fissure walls. This study should include phase identification, textures as well as mineral chemistry. The information from this study is fundamental for the decision of further investigations. Mineral chemistry including isotopes and fluid inclusion studies will give an essential knowledge about crystallization conditions for fissure minerals concerned. Direct dating using fission tracks as well as radioactive isotopes could be useful for some minerals. Application of thermoluminescens dating on fissure minerals is doubtful. (Auth.)

  5. Analytical dual-energy microtomography: A new method for obtaining three-dimensional mineral phase images and its application to Hayabusa samples

    Science.gov (United States)

    Tsuchiyama, A.; Nakano, T.; Uesugi, K.; Uesugi, M.; Takeuchi, A.; Suzuki, Y.; Noguchi, R.; Matsumoto, T.; Matsuno, J.; Nagano, T.; Imai, Y.; Nakamura, T.; Ogami, T.; Noguchi, T.; Abe, M.; Yada, T.; Fujimura, A.

    2013-09-01

    We developed a novel technique called "analytical dual-energy microtomography" that uses the linear attenuation coefficients (LACs) of minerals at two different X-ray energies to nondestructively obtain three-dimensional (3D) images of mineral distribution in materials such as rock specimens. The two energies are above and below the absorption edge energy of an abundant element, which we call the "index element". The chemical compositions of minerals forming solid solution series can also be measured. The optimal size of a sample is of the order of the inverse of the LAC values at the X-ray energies used. We used synchrotron-based microtomography with an effective spatial resolution of >200 nm to apply this method to small particles (30-180 μm) collected from the surface of asteroid 25143 Itokawa by the Hayabusa mission of the Japan Aerospace Exploration Agency (JAXA). A 3D distribution of the minerals was successively obtained by imaging the samples at X-ray energies of 7 and 8 keV, using Fe as the index element (the K-absorption edge of Fe is 7.11 keV). The optimal sample size in this case is of the order of 50 μm. The chemical compositions of the minerals, including the Fe/Mg ratios of ferromagnesian minerals and the Na/Ca ratios of plagioclase, were measured. This new method is potentially applicable to other small samples such as cosmic dust, lunar regolith, cometary dust (recovered by the Stardust mission of the National Aeronautics and Space Administration [NASA]), and samples from extraterrestrial bodies (those from future sample return missions such as the JAXA Hayabusa2 mission and the NASA OSIRIS-REx mission), although limitations exist for unequilibrated samples. Further, this technique is generally suited for studying materials in multicomponent systems with multiple phases across several research fields.

  6. Characterization of mineral phases of agricultural soil samples of Colombian coffee using Mössbauer spectroscopy and X-ray diffraction

    Science.gov (United States)

    Rodríguez, Humberto Bustos; Lozano, Dagoberto Oyola; Martínez, Yebrayl Antonio Rojas; Pinilla, Marlene Rivera; Alcázar, German Antonio Pérez

    2012-03-01

    Soil chemical analysis, X-ray diffraction (XRD) and Mössbauer spectrometry (MS) of 57Fe were used to characterize mineral phases of samples taken from the productive layer (horizon A) of agricultural coffee soil from Tolima (Colombia). Chemical analysis shows the chemical and textural parameters of samples from two different regions of Tolima, i.e., Ibagué and Santa Isabel. By XRD phases like illite (I), andesine (A) and quartz (Q) in both samples were identified. The quantity of these phases is different for the two samples. The MS spectra taken at room temperature were adjusted by using five doublets, three of them associated to Fe + 3 type sites and the other two to Fe + 2 type sites. According to their isomer shift and quadrupole splitting the presence of phases like illite (detected by DRX), nontronite and biotite (not detected by XRD) can be postulated.

  7. Characterization of mineral phases of agricultural soil samples of Colombian coffee using Mössbauer spectroscopy and X-ray diffraction

    International Nuclear Information System (INIS)

    Rodríguez, Humberto Bustos; Lozano, Dagoberto Oyola; Martínez, Yebrayl Antonio Rojas; Pinilla, Marlene Rivera; Alcázar, German Antonio Pérez

    2012-01-01

    Soil chemical analysis, X-ray diffraction (XRD) and Mössbauer spectrometry (MS) of 57 Fe were used to characterize mineral phases of samples taken from the productive layer (horizon A) of agricultural coffee soil from Tolima (Colombia). Chemical analysis shows the chemical and textural parameters of samples from two different regions of Tolima, i.e., Ibagué and Santa Isabel. By XRD phases like illite (I), andesine (A) and quartz (Q) in both samples were identified. The quantity of these phases is different for the two samples. The MS spectra taken at room temperature were adjusted by using five doublets, three of them associated to Fe  + 3 type sites and the other two to Fe  + 2 type sites. According to their isomer shift and quadrupole splitting the presence of phases like illite (detected by DRX), nontronite and biotite (not detected by XRD) can be postulated.

  8. Technetium Reduction and Permanent Sequestration by Abiotic and Biotic Formation of Low-Solubility Sulfide Mineral Phases

    Energy Technology Data Exchange (ETDEWEB)

    Tratnyek, Paul G. [Oregon Health & Science Univ., Beaverton, OR (United States); Tebo, Bradley M. [Oregon Health & Science Univ., Beaverton, OR (United States); Fan, Dimin [Oregon Health & Science Univ., Beaverton, OR (United States); Anitori, Roberto [Oregon Health & Science Univ., Beaverton, OR (United States); Szecsody, Jim [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jansik, Danielle [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-11-14

    One way to minimize the mobility of the TcVII oxyanion pertechnetate (TcO4-) is to effect reduction under sulfidogenic conditions (generated abiotically by Fe0 or biotically) to form TcSx, which is significantly slower to oxidize than TcIVO2. In sediment systems, TcSx and other precipitates may oxidize more slowly due to oxygen diffusion limitations to these low permeability precipitate zones. In addition, the TcO4- reduction rate may be more rapid in the presence of sediment because of additional reductive surface phases. This project aims to provide a fundamental understanding of the feasibility of immobilization of TcO4- as TcSx in the vadose zone or groundwater by application nano zero-valent iron (nZVI), and sulfide or sulfate. Biotic batch experiments have used the sulfate-reducing bacterium (SRB) Desulfotomaculum reducens. The iron sulfide mineral mackinawite was generated under these conditions, while vivianite was formed in nZVI only controls. The sulfide/bacteria-containing system consistently reduced aqueous pertechnetate rapidly (> 95% in the first hour), a rate similar to that for the sulfide-free, nZVI only system. Reduced Tc (aged for 3 months) generated in both SRB/nZVI systems was highly resistant to reoxidation. In reduced samples, Tc was found associated with solid phases containing Fe and S (D. reducens/nZVI) or Fe (nZVI only). Experiments using D. reducens without nZVI provided some additional insights. Firstly, stationary phase cultures were able to slowly reduce pertechnetate. Secondly, addition of pertechnetate at the beginning of cell growth (lag phase) resulted in a faster rate of Tc reduction, possibly indicating a direct (e.g. enzymatic) role for D. reducens in Tc reduction. Abiotic batch experiments were conducted with Na2S as the sulfide source. Pertechnetate reduction was

  9. Mineral chemistry of radioactive and associated phases from neoproterozoic unconformity related uranium deposits from Koppunuru, Palnad sub-basin, Guntur District, Andhra Pradesh, India

    International Nuclear Information System (INIS)

    Paul, A.K.; Rajagopalan, V.; Shivakumar, K.; Verma, M.B.

    2011-01-01

    Unconformity proximal uranium mineralization at Koppunuru occurs in basement granitoids and the overlying Banganalapalle Formation of Kurnool Group in Palnad sub-basin. The U-mineralization transgresses the unconformity both above and below. Later remobilization of uranium is evident, as they are intermittently intercepted within the sediments overlying the unconformity. Subsurface exploration by drilling intercepted three mineralization bands, viz. Band A and B upto 80m above the unconformity in the overlying Banganapalle quartzite and Band C, mostly sub-parallel to the unconformity and confined to basal conglomerate/grit horizon except a few boreholes where it is transgressing to granitic horizon ( 2 (upto 2.00 %), ThO 2 (0.03 to 1.51 %) and RE 2 O 3 (0.12 to 3.56 %). Such activities signify the processes of epigenetic fluid/gel related to U-concentration. At increasing depths, possibility of AI- bearing radioactive phases is also envisaged. The radioactive phases present in the samples reveal negligible to low thorium indicating low temperature phenomena. They are likely to be emplaced by the epigenetic solution/gel rich in U, Ti, Si, AI, Ca, P and Pb, preferably along available spaces as vein, cavity and grain boundary. U-associated sulphides occurring as veins and fracture fills, essentially comprise pyrite, pyrrhotite, chalcopyrite, pentlandite and galena. They have normal chemistry but for subtle variations in minor elements. The pyrite and pyrrhotite are invariably arseniferous and they dominate the sulphides. Thus, it is concluded that the area has potential for multi-episodic epigenetic U-mineralization

  10. Thermodynamic properties and phase equilibria of the secondary copper minerals libethenite, olivenite, pseudomalachite, kröhnkite, cyanochroite, and devilline

    Czech Academy of Sciences Publication Activity Database

    Majzlan, J.; Zittlau, A.H.; Grevel, K.-D.; Schliesser, J.; Woodfield, B. F.; Dachs, E.; Števko, M.; Chovan, M.; Plášil, Jakub; Sejkora, J.; Milovská, S.

    2015-01-01

    Roč. 53, č. 5 (2015), s. 937-960 ISSN 0008-4476 Institutional support: RVO:68378271 Keywords : secondary copper minerals * thermodynamics * pE–pH diagrams * Lippmann diagrams for solid solutions * infrared and Raman spectra Subject RIV: DB - Geology ; Mineralogy Impact factor: 0.862, year: 2015

  11. Biomineralization of calcium carbonate in the cell wall of Lithothamnion crispatum (Hapalidiales, Rhodophyta): correlation between the organic matrix and the mineral phase.

    Science.gov (United States)

    de Carvalho, Rodrigo Tomazetto; Salgado, Leonardo Tavares; Amado Filho, Gilberto Menezes; Leal, Rachel Nunes; Werckmann, Jacques; Rossi, André Linhares; Campos, Andrea Porto Carreiro; Karez, Cláudia Santiago; Farina, Marcos

    2017-06-01

    Over the past few decades, progress has been made toward understanding the mechanisms of coralline algae mineralization. However, the relationship between the mineral phase and the organic matrix in coralline algae has not yet been thoroughly examined. The aim of this study was to describe the cell wall ultrastructure of Lithothamnion crispatum, a cosmopolitan rhodolith-forming coralline algal species collected near Salvador (Brazil), and examine the relationship between the organic matrix and the nucleation and growth/shape modulation of calcium carbonate crystals. A nanostructured pattern was observed in L. crispatum along the cell walls. At the nanoscale, the crystals from L. crispatum consisted of several single crystallites assembled and associated with organic material. The crystallites in the bulk of the cell wall had a high level of spatial organization. However, the crystals displayed cleavages in the (104) faces after ultrathin sectioning with a microtome. This organism is an important model for biomineralization studies as the crystallographic data do not fit in any of the general biomineralization processes described for other organisms. Biomineralization in L. crispatum is dependent on both the soluble and the insoluble organic matrix, which are involved in the control of mineral formation and organizational patterns through an organic matrix-mediated process. This knowledge concerning the mineral composition and organizational patterns of crystals within the cell walls should be taken into account in future studies of changing ocean conditions as they represent important factors influencing the physico-chemical interactions between rhodoliths and the environment in coralline reefs. © 2017 Phycological Society of America.

  12. EFFECT OF FERRITE PHASE ON THE FORMATION AND COEXISTENCE OF 3CaO.3Al₂O₃.CaSO₄ AND 3CaO.SiO₂ MINERALS

    Directory of Open Access Journals (Sweden)

    Xiaolei Lu

    2017-12-01

    Full Text Available The effect of ferrite on the formation and coexistence of 3CaO.3Al₂O₃.CaSO₄ (C₄A₃$ and 3CaO.SiO₂ (C3S was investigated in this paper. The results indicate that 20 % content of ferrite phase with the composition of C₂A0.5F0.5 can facilitate the coexistence of C₄A₃$ and C₃S solid solutions at 1350 ° C. There are other trace elements that incorporate into clinker minerals and form solid solutions. In addition, the dark and polygonal C₄A₃$ solid solution is not dissolved in liquid phase at 1350 ° C. It can promote the burnability of the raw mixes and provide a favorable condition for the formation of C₃S. However, it has an adverse effect on the coexistence of two clinker minerals with the changing of ferrite compositions. This will provide the important basis for the preparation of the calcium sulphoaluminate cement clinker containing C₃S.

  13. A New Method of Absorption-Phase Nanotomography for 3D Observation of Mineral-Organic-Water Textiles and its Application to Pristine Carbonaceous Chondrites

    Science.gov (United States)

    Tsuchiyama, A.; Nakato, A.; Matsuno, J.; Sugimoto, M.; Uesugi, K.; Takeuchi, A.; Nakano, T.; Vaccaro, E.; Russel, S.; Nakamura-Messenger, K.; hide

    2017-01-01

    Pristine carbonaceous chondrites contain fine-grained matrix, which is composed largely of amorphous silicates, sub-micron silicate and sulfide crystals, and organic materials. They are regarded as primitive dust in the early Solar System that have suffered minimal alteration in their parent bodies. The matrix generally has different lithologies; some of them are unaltered but some are more or less aqueously altered. Their textures have been examined in 2D usually by FE-SEM/EDS, TEM/EDS, nano-SIMS and micro-XRD. Observation of their complex fine textures, such as spatial relation between different lithologies in 3D, is important for understanding aggregation and alteration processes. Synchrotron radiation (SR)-based X-ray tomography reveals 3D structures nondestructively with high spatial resolution of approximately greater than 100 nm. We have developed a new technique using absorption contrasts called "dual-energy tomography" (DET) to obtain 3D distribution of minerals at SPring-8, SR facility in Japan, and applied successfully to Itokawa particles. Phase and absorption contrast images can be simultaneously obtained in 3D by using "scanning-imaging x-ray microscopy" (SIXM) at SPring-8, which can discriminate between void, water and organic materials. We applied this technique combined with FIB micro-sampling to carbonaceous chondrites to search for primitive liquid water. In this study, we combined the DET and SIXM to obtain three dimensional submicron-scale association between minerals, organic materials and water and applied this to pristine carbonaceous chondrites.

  14. Combining selective sequential extractions, X-Ray Absorption Spectroscopy, and X-Ray Powder Diffraction for Cu (II speciation in soil and mineral phases

    Directory of Open Access Journals (Sweden)

    Tatiana Minkina

    2017-04-01

    Full Text Available Interaction of Cu (II ions with the matrix of soil and mineral phases of layered silicates was assessed by the Miller method of selective sequential fractionation and a set of synchrotron X-ray methods, including X-ray powder diffraction (XRD and X-ray absorption spectroscopy (XANES. It was shown that the input of Cu into Calcic Chernozem in the form of monoxide (CuO and salt (Cu(NO32 affected the transformation of Cu compounds and their affinity for metal-bearing phases. It was found that the contamination of soil with a soluble Cu(II salt increased the bioavailability of the metal and the role of organic matter and Fe oxides in the fixation and retention of Cu. During the incubation of soil with Cu monoxide, the content of the metal in the residual fractions increased, which was related to the possible entry of Cu in the form of isomorphic impurities into silicates, as well as to the incomplete dissolution of exogenic compounds at the high level of their input into the soil. A mechanism for the structural transformation of minerals was revealed, which showed that ion exchange processes result in the sorption of Cu (II ions from the saturated solution by active sites on the internal surface of the lattice of dioctahedral aluminosilicates. Surface hydroxyls at the octahedral aluminum atom play the main role. X-ray diagnostics revealed that excess Cu(II ions are removed from the system due to the formation and precipitation of coarsely crystalline Cu(NO3(OH3.

  15. Characterization of manganese phases in mineral processing products of the Azul Mine, Carajas. Metallurgical implications; Caracterizacao de fases manganesiferas em produtos de beneficiamento da Mina do Azul, Carajas. Implicacoes metalurgicas

    Energy Technology Data Exchange (ETDEWEB)

    Pereira, G.; Fernandez, O.J.Ch., E-mail: pereiragilcimar@hotmail.co, E-mail: ochoque.fernandez@gmail.co [Instituto Federal de Ciencia e Tecnologia do Para (IFPA), Belem, PA (Brazil). Curso de Engenharia de Materiais; Costa, M.L. da, E-mail: mlc@ufpa.b [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Inst. de Geociencias

    2010-07-01

    Were characterized the manganese phases of the processing products using ore microscopy and x-ray diffraction, in order to contribute with new data and help the processing operations of the mine. Cryptomelane is the main manganese mineral in products, and pyrolusite and nsutite are in minor proportion. Were observed distinctive textures of the cryptomelane and others manganese phases, it were formed in different geological times and therefore affecting the operations in mineral processing, principally, comminution. The observed mineralogical variations affect too the unit operations when expand the pit. (author)

  16. Miners' welfare

    Energy Technology Data Exchange (ETDEWEB)

    Buckley, C

    1984-06-13

    The Miners' Welfare Committee (MWC) was formed in Britain in 1921 and initiated building programmes to provide welfare amenities for miners and families, using architecture to improve the quality of a miner's working and leisure time. The article reviews the MWC's work, and assesses the design and architecture at the Selby Coalfield. (7 refs.)

  17. Preparation and thermal properties of mineral-supported polyethylene glycol as form-stable composite phase change materials (CPCMs) used in asphalt pavements.

    Science.gov (United States)

    Jin, Jiao; Lin, Feipeng; Liu, Ruohua; Xiao, Ting; Zheng, Jianlong; Qian, Guoping; Liu, Hongfu; Wen, Pihua

    2017-12-05

    Three kinds of mineral-supported polyethylene glycol (PEG) as form-stable composite phase change materials (CPCMs) were prepared to choose the most suitable CPCMs in asphalt pavements for the problems of asphalt pavements rutting diseases and urban heat islands. The microstructure and chemical structure of CPCMs were characterized by SEM, FT-IR and XRD. Thermal properties of the CPCMs were determined by TG and DSC. The maximum PEG absorption of diatomite (DI), expanded perlite (EP) and expanded vermiculite (EVM) could reach 72%, 67% and 73.6%, respectively. The melting temperatures and latent heat of CPCMs are in the range of 52-55 °C and 100-115 J/g, respectively. The results show that PEG/EP has the best thermal and chemical stability after 100 times of heating-cooling process. Moreover, crystallization fraction results show that PEG/EP has slightly higher latent heats than that of PEG/DI and PEG/EVM. Temperature-adjusting asphalt mixture was prepared by substituting the fine aggregates with PEG/EP CPCMs. The upper surface maximum temperature difference of temperature-adjusting asphalt mixture reaches about 7.0 °C in laboratory, and the surface peak temperature reduces up to 4.3 °C in the field experiment during a typical summer day, indicating a great potential application for regulating pavement temperature field and alleviating the urban heat islands.

  18. Study of a ;hot; particle with a matrix of U-bearing metallic Zr: Clue to supercriticality during the Chernobyl nuclear accident

    Science.gov (United States)

    Pöml, P.; Burakov, B.

    2017-05-01

    This paper is dedicated to the 30th anniversary of the severe nuclear accident that occurred at the Chernobyl NPP on 26 April 1986. A detailed study on a Chernobyl "hot" particle collected from contaminated soil was performed. Optical and electron microscopy, as well as quantitative x-ray microbeam analysis methods were used to determine the properties of the sample. The results show that the particle (≈ 240 x 165 μm) consists of a metallic Zr matrix containing 2-3 wt. % U and bearing veins of an U,Nb admixture. The metallic Zr matrix contains two phases with different amounts of O with the atomic proportions (U,Zr,Nb)0.73O0.27 and (U,Zr,Nb)0.61O0.39. The results confirm the interaction between UO2 fuel and zircaloy cladding in the reactor core. To explain the process of formation of the particle, its properties are compared to laboratory experiments. Because of the metallic nature of the particle it is concluded that it must have formed during a very high temperature (> 2400∘C) process that lasted for only a very short time (few microseconds or less); otherwise the particle should have been oxidised. Such a rapid very high temperature process indicates that at least part of the reactor core could have been supercritical prior to an explosion as it was previously suggested in the literature.

  19. Methodology for determination of trace elements in mineral phases of iron banded formation by LA-ICP-MS; Metodologia de determinacao de elementos-traco em fases minerais de formacoes ferriferas bandadas por LA-ICP-MS

    Energy Technology Data Exchange (ETDEWEB)

    Sousa, Denise V.M. de; Nalini Junior, Herminio A.; Sampaio, Geraldo M.S.; Abreu, Adriana T. de; Lana, Cristiano de C., E-mail: deniseversiane2@yahoo.com.br, E-mail: nalini@degeo.ufop.br, E-mail: geraldomssampaio@gmail.com, E-mail: adrianatropia@gmail.com, E-mail: cristianodeclana@gmail.com [Universidade Federal de Ouro Preto (DEGEO/UFOP), Ouro Preto, MG (Brazil). Departamento de Geologia

    2015-07-01

    The study of the chemical composition of mineral phases of iron formation (FF), especially of trace elements, is an important tool in the understanding of the genesis of these rocks and the contribution of the phases in the composition of whole rock. Low mass fraction of such elements in the mineral phases present in this rock type requires a suitable analytical procedure. The laser ablation technique coupled with ICP-MS (LA-ICP-MS) has been widely used for determination of trace elements in geological samples. Thus, the aim of this study is to develop calibration curves for determination of trace elements (Y, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb and Lu) in mineral phases of banded iron formations by LA-ICP-MS. Several certified reference materials (CRM) were used for calibrate the equipment. The analytical conditions were checked by CRM NIST SRM 614. The results were satisfactory, since the curves showed good linearity coefficients, good accuracy and precision of results. (author)

  20. GOLD MINERAL PROSPECTING USING PHASED ARRAY TYPE L-BAND SYNTHETIC APERTURE RADAR (PALSAR SATELLITE REMOTE SENSING DATA, CENTRAL GOLD BELT, MALAYSIA

    Directory of Open Access Journals (Sweden)

    A. Beiranvand Pour

    2016-06-01

    Full Text Available The Bentong-Raub Suture Zone (BRSZ of Peninsular Malaysia is one of the significant structural zones in Sundaland, Southeast Asia. It forms the boundary between the Gondwana-derived Sibumasu terrane in the west and Sukhothai arc in the east. The BRSZ is also genetically related to the sediment-hosted/orogenic gold deposits associated with the major lineaments and form-lines in the central gold belt Central Gold Belt of Peninsular Malaysia. In tropical environments, heavy tropical rainforest and intense weathering makes it impossible to map geological structures over long distances. Advances in remote sensing technology allow the application of Synthetic Aperture Radar (SAR data in geological structural analysis for tropical environments. In this investigation, the Phased Array type L-band Synthetic Aperture Radar (PALSAR satellite remote sensing data were used to analyse major geological structures in Peninsular Malaysia and provide detailed characterization of lineaments and form-lines in the BRSZ, as well as its implication for sediment-hosted/orogenic gold exploration in tropical environments. The major geological structure directions of the BRSZ are N-S, NNE-SSW, NE-SW and NW-SE, which derived from directional filtering analysis to PALSAR data. The pervasive array of N-S faults in the study area and surrounding terrain is mainly linked to the N-S trending of the Suture Zone. N-S striking lineaments are often cut by younger NE-SW and NW-SE-trending lineaments. Gold mineralized trends lineaments are associated with the intersection of N-S, NE-SW, NNW-SSE and ESE-WNW faults and curvilinear features in shearing and alteration zones. Lineament analysis on PALSAR satellite remote sensing data is a useful tool for detecting the boundary between the Gondwana-derived terranes and major geological features associated with suture zone especially for large inaccessible regions in tropical environments.

  1. A phase I feasibility study of multi-modality imaging assessing rapid expansion of marrow fat and decreased bone mineral density in cancer patients.

    Science.gov (United States)

    Hui, Susanta K; Arentsen, Luke; Sueblinvong, Thanasak; Brown, Keenan; Bolan, Pat; Ghebre, Rahel G; Downs, Levi; Shanley, Ryan; Hansen, Karen E; Minenko, Anne G; Takhashi, Yutaka; Yagi, Masashi; Zhang, Yan; Geller, Melissa; Reynolds, Margaret; Lee, Chung K; Blaes, Anne H; Allen, Sharon; Zobel, Bruno Beomonte; Le, Chap; Froelich, Jerry; Rosen, Clifford; Yee, Douglas

    2015-04-01

    Cancer survivors are at an increased risk for fractures, but lack of effective and economical biomarkers limits quantitative assessments of marrow fat (MF), bone mineral density (BMD) and their relation in response to cytotoxic cancer treatment. We report dual energy CT (DECT) imaging, commonly used for cancer diagnosis, treatment and surveillance, as a novel biomarker of MF and BMD. We validated DECT in pre-clinical and phase I clinical trials and verified with water-fat MRI (WF-MRI), quantitative CT (QCT) and dual-energy X-ray absorptiometry (DXA). Basis material composition framework was validated using water and small-chain alcohols simulating different components of bone marrow. Histologic validation was achieved by measuring percent adipocyte in the cadaver vertebrae and compared with DECT and WF-MRI. For a phase I trial, sixteen patients with gynecologic malignancies (treated with oophorectomy, radiotherapy or chemotherapy) underwent DECT, QCT, WF-MRI and DXA before and 12months after treatment. BMD and MF percent and distribution were quantified in the lumbar vertebrae and the right femoral neck. Measured precision (3mg/cm(3)) was sufficient to distinguish test solutions. Adiposity in cadaver bone histology was highly correlated with MF measured using DECT and WF-MRI (r=0.80 and 0.77, respectively). In the clinical trial, DECT showed high overall correlation (r=0.77, 95% CI: 0.69, 0.83) with WF-MRI. MF increased significantly after treatment (p<0.002). Chemotherapy and radiation caused greater increases in MF than oophorectomy (p<0.032). L4 BMD decreased 14% by DECT, 20% by QCT, but only 5% by DXA (p<0.002 for all). At baseline, we observed a statistically significant inverse association between MF and BMD which was dramatically attenuated after treatment. Our study demonstrated that DECT, similar to WF-MRI, can accurately measure marrow adiposity. Both imaging modalities show rapid increase in MF following cancer treatment. Our results suggest that MF and

  2. Aggregate and Mineral Resources - Minerals

    Data.gov (United States)

    NSGIC State | GIS Inventory — This point occurrence data set represents the current mineral and selected energy resources of Utah. The data set coordinates were derived from USGS topographic maps...

  3. BET measurements: Outgassing of minerals

    DEFF Research Database (Denmark)

    Clausen, Liselotte; Fabricius, Ida Lykke

    2000-01-01

    Outgassing minerals at elevated temperatures prior to BET measurements can lead to phase changes, especially in the case of amorphous and poorly crystalline materials. In order to evaluate the applicability of the BET method when low outgassing temperatures are required, selected aquifer minerals...... were outgassed at different temperatures and for different times. The studied minerals are 2-line ferrihydrite, goethite, lepidocrocite, quartz, calcite, ®-alumina, and kaolinite. The results demonstrate that measured specific surface areas of iron oxides are strongly dependent on outgassing conditions...... because the surface area increased by 170% with increasing temperature. In the poorly crystalline minerals, phase changes caused by heating were observed at temperatures lower than 100±C. Therefore low outgassing temperatures are preferable for minimizing phase changes. As demonstrated in this study...

  4. Fumarolic minerals

    DEFF Research Database (Denmark)

    Balic Zunic, Tonci; Garavelli, Anna; Jakobsson, Sveinn Peter

    2016-01-01

    The fumarolic mineralogy of the Icelandic active volcanoes, the Tyrrhenian volcanic belt (Italy) and the Aegean active arc (Greece) is investigated, and literature data surveyed in order to define the characteristics of the European fumarolic systems. They show broad diversity of mineral...... associations, with Vesuvius and Vulcano being also among the world localities richest in mineral species. Volcanic systems, which show recession over a longer period, show fumarolic development from the hightemperature alkaline halide/sulphate, calcic sulphate or sulphidic parageneses, synchronous...... with or immediately following the eruptions, through mediumtemperature ammonium minerals, metal chlorides, or fluoride associations to the late low-temperature paragenesis dominated by sulphur, gypsum, alunogen, and other hydrous sulphates. The situation can be different in the systems that are not recessing but show...

  5. Mineral sands

    International Nuclear Information System (INIS)

    Anon.

    1990-01-01

    This paper presents an outlook of the Australian mineral sand industry and covers the major operators. It is shown that conscious of an environmentally minded public, the Australian miners have led the way in the rehabilitation of mined areas. Moreover the advanced ceramic industry is generating exciting new perspectives for zircon producers and there is a noticeable growth in the electronic market for rare earths, but in long term the success may depend as much on environmental management and communication skills as on mining and processing skills

  6. Contrasting estimates on the depth of magma storage zones in volcanic systems from mineral barometry and phase equilibrium experiments: a case study from Mount Merapi, Indonesia

    Science.gov (United States)

    Erdmann, Saskia; Martel, Caroline

    2015-04-01

    Mount Merapi, located in central Java, erupts on average every 5-10 years by discharging block-and-ash flows that pose local, but spatially restricted hazards. In 2010, however, the volcano erupted with a force that has been unprecedented in over 100 years. Its proximity to the metropolis of Yogyakarta with a population of >4 million makes short- and long-term eruption forecasting a task of vital importance. Critical to the appraisal of the volcano's hazard potential are tight constraints on its upper-crustal magma plumbing system and particularly on the location of its pre-eruptive reservoir. Previous petrological studies have estimated on the basis of amphibole and clinopyroxene barometry that the main magma storage zone below Merapi is located at depths of >10-15 km, while geophysical surveys have inferred significant magma storage zones at depths of ~5.5-9 km. We have carried out phase equilibrium experiments on basaltic andesite erupted in 2010, which indicate that the main pre-eruptive reservoir is located at a depth of ~7-8 km (~200 MPa). Our results thus corroborate the findings of earlier geophysical surveys and highlight the extreme uncertainty of mineral-based pressure estimates for volcanic magma systems. We point out that the commonly employed amphibole barometric calibrations of Ridolfi et al. (2010) and Ridolfi & Renzulli (2012) calculate low crystallization pressure for amphibole crystallized from felsic melt and high crystallization pressure for amphibole crystallized from mafic melt, and that the calculated pressure is thus largely unrelated to true values. Commonly employed clinopyroxene barometers (e.g., those of Nimis 1999; Putirka 2008) are also of limited use for estimating the location of crustal magma reservoirs, because the methods have large standard errors and are extremely temperature-sensitive. As a result, the calculated crystallization pressures inevitably indicate crystallization over a large range of depths, often from deep- to

  7. Data set for the proteomic inventory and quantitative analysis of chicken eggshell matrix proteins during the primary events of eggshell mineralization and the active growth phase of calcification.

    Science.gov (United States)

    Marie, Pauline; Labas, Valérie; Brionne, Aurélien; Harichaux, Grégoire; Hennequet-Antier, Christelle; Rodriguez-Navarro, Alejandro B; Nys, Yves; Gautron, Joël

    2015-09-01

    Chicken eggshell is a biomineral composed of 95% calcite calcium carbonate mineral and of 3.5% organic matrix proteins. The assembly of mineral and its structural organization is controlled by its organic matrix. In a recent study [1], we have used quantitative proteomic, bioinformatic and functional analyses to explore the distribution of 216 eggshell matrix proteins at four key stages of shell mineralization defined as: (1) widespread deposition of amorphous calcium carbonate (ACC), (2) ACC transformation into crystalline calcite aggregates, (3) formation of larger calcite crystal units and (4) rapid growth of calcite as columnar structure with preferential crystal orientation. The current article detailed the quantitative analysis performed at the four stages of shell mineralization to determine the proteins which are the most abundant. Additionally, we reported the enriched GO terms and described the presence of 35 antimicrobial proteins equally distributed at all stages to keep the egg free of bacteria and of 81 proteins, the function of which could not be ascribed.

  8. Data set for the proteomic inventory and quantitative analysis of chicken eggshell matrix proteins during the primary events of eggshell mineralization and the active growth phase of calcification

    Directory of Open Access Journals (Sweden)

    Pauline Marie

    2015-09-01

    Full Text Available Chicken eggshell is a biomineral composed of 95% calcite calcium carbonate mineral and of 3.5% organic matrix proteins. The assembly of mineral and its structural organization is controlled by its organic matrix. In a recent study [1], we have used quantitative proteomic, bioinformatic and functional analyses to explore the distribution of 216 eggshell matrix proteins at four key stages of shell mineralization defined as: (1 widespread deposition of amorphous calcium carbonate (ACC, (2 ACC transformation into crystalline calcite aggregates, (3 formation of larger calcite crystal units and (4 rapid growth of calcite as columnar structure with preferential crystal orientation. The current article detailed the quantitative analysis performed at the four stages of shell mineralization to determine the proteins which are the most abundant. Additionally, we reported the enriched GO terms and described the presence of 35 antimicrobial proteins equally distributed at all stages to keep the egg free of bacteria and of 81 proteins, the function of which could not be ascribed.

  9. Anisotropy of out-of-phase magnetic susceptibility of rocks as a tool for direct determination of magnetic subfabrics of some minerals: an introductory study

    Czech Academy of Sciences Publication Activity Database

    Hrouda, F.; Chadima, Martin; Ježek, J.; Pokorný, J.

    2017-01-01

    Roč. 208, č. 1 (2017), s. 385-402 ISSN 0956-540X R&D Projects: GA AV ČR IAAX00130801 Institutional support: RVO:67985831 Keywords : magnetic and electrical properties * magnetic fabrics and anisotropy * magnetic mineralogy and petrology * rock and mineral magnetism Subject RIV: DB - Geology ; Mineralogy OBOR OECD: Geology Impact factor: 2.414, year: 2016

  10. Hydrothermal minerals

    Digital Repository Service at National Institute of Oceanography (India)

    Nath, B.N.

    flux. Circulation of seawater through the oceanic crust and upper mantle gives rise to a complex series of physical and chemical reactions that lead to the 1) formation of seafloor mineral deposits; 2) alteration of oceanic crust; 3) control... temperature in the high-temperature reaction zone near the heat source. Important parameters in determining the high- temperature fluid composition are • pressure, • temperature, • water/rock ratio, • rock composition, • recharge fluid...

  11. Digital mineral logging system

    International Nuclear Information System (INIS)

    West, J.B.

    1980-01-01

    A digital mineral logging system acquires data from a mineral logging tool passing through a borehole and transmits the data uphole to an electronic digital signal processor. A predetermined combination of sensors, including a deviometer, is located in a logging tool for the acquisition of the desired data as the logging tool is raised from the borehole. Sensor data in analog format is converted in the logging tool to a digital format and periodically batch transmitted to the surface at a predetermined sampling rate. An identification code is provided for each mineral logging tool, and the code is transmitted to the surface along with the sensor data. The self-identifying tool code is transmitted to the digital signal processor to identify the code against a stored list of the range of numbers assigned to that type of tool. The data is transmitted up the d-c power lines of the tool by a frequency shift key transmission technique. At the surface, a frequency shift key demodulation unit transmits the decoupled data to an asynchronous receiver interfaced to the electronic digital signal processor. During a recording phase, the signals from the logging tool are read by the electronic digital signal processor and stored for later processing. During a calculating phase, the stored data is processed by the digital signal processor and the results are outputted to a printer or plotter, or both

  12. X-ray micro-analysis of the mineralization patterns in developing enamel in hamster tooth germs exposed to fluoride in vitro during the secretory phase of amelogenesis

    International Nuclear Information System (INIS)

    Lyaruu, D.M.; Blijleven, N.; Hoeben-Schornagel, K.; Bronckers, A.L.; Woeltgens, J.H.

    1989-01-01

    The developing enamel from three-day-old hamster first maxillary (M1) molar tooth germs exposed to fluoride (F-) in vitro was analyzed for its mineral content by means of the energy-dispersive x-ray microanalysis technique. The aim of this study was to obtain semi-quantitative data on the F(-)-induced hypermineralization patterns in the enamel and to confirm that the increase in electron density observed in micrographs of F(-)-treated enamel is indeed due to an increase in mineral content in the fluorotic enamel. The tooth germs were explanted during the early stages of secretory amelogenesis and initially cultured for 24 hr in the presence of 10 ppm F- in the culture medium. The germs were then cultured for another 24 hr without F-. In order to compare the ultrastructural results directly with the microprobe data, we used the same specimens for both investigations. The net calcium counts (measurement minus background counts) in the analyses were used as a measure of the mineral content in the enamel. The aprismatic pre-exposure enamel, deposited in vivo before the onset of culture, was the most hypermineralized region in the fluorotic enamel, i.e., it contained the highest amount of calcium measured. The degree of the F(-)-induced hypermineralization gradually decreased (but was not abolished) in the more mature regions of the enamel. The unmineralized enamel matrix secreted during the initial F- treatment in vitro mineralized during the subsequent culture without F-. The calcium content in this enamel layer was in the same order of magnitude as that recorded for the newly deposited enamel in control tooth germs cultured without F-

  13. TUCS/phosphate mineralization of actinides

    Energy Technology Data Exchange (ETDEWEB)

    Nash, K.L. [Argonne National Lab., IL (United States)

    1997-10-01

    This program has as its objective the development of a new technology that combines cation exchange and mineralization to reduce the concentration of heavy metals (in particular actinides) in groundwaters. The treatment regimen must be compatible with the groundwater and soil, potentially using groundwater/soil components to aid in the immobilization process. The delivery system (probably a water-soluble chelating agent) should first concentrate the radionuclides then release the precipitating anion, which forms thermodynamically stable mineral phases, either with the target metal ions alone or in combination with matrix cations. This approach should generate thermodynamically stable mineral phases resistant to weathering. The chelating agent should decompose spontaneously with time, release the mineralizing agent, and leave a residue that does not interfere with mineral formation. For the actinides, the ideal compound probably will release phosphate, as actinide phosphate mineral phases are among the least soluble species for these metals. The most promising means of delivering the precipitant would be to use a water-soluble, hydrolytically unstable complexant that functions in the initial stages as a cation exchanger to concentrate the metal ions. As it decomposes, the chelating agent releases phosphate to foster formation of crystalline mineral phases. Because it involves only the application of inexpensive reagents, the method of phosphate mineralization promises to be an economical alternative for in situ immobilization of radionuclides (actinides in particular). The method relies on the inherent (thermodynamic) stability of actinide mineral phases.

  14. Sorption of pesticides to aquifer minerals

    DEFF Research Database (Denmark)

    Clausen, Liselotte; Fabricius, Ida Lykke

    2000-01-01

    This paper summarizes results from a work were the sorption of five pesticides on seven minerals were studied in order to quantify the adsorption to different mineral surfaces. Investigated mineral phases are: quartz, calcite, kaolinite, a-alumina, and three iron oxides (2-line ferrihydrite......, goethite, lepidocrocite). Selected pesticides are: atrazine, isoproturon, mecoprop, 2,4-D, and bentazone. The results demonstrate that pesticides adsorb to pure mineral surfaces. However, the size of the adsorption depends on the type of pesticide and the type of mineral....

  15. Variation of properties of clayey minerals and associated phases about uranium deposits related to proterozoic discordances; Variation des proprietes des mineraux argileux et des phases associees autour des gisements d'uranium lies aux discordances Proterozoiques

    Energy Technology Data Exchange (ETDEWEB)

    Beaufort, D.; Patrier, P.; Laverret, E.; Gaboreau, St.; Billault, V. [HYDRASA, Universite de Poitiers-CNRS, 86 - Poitiers (France); Quirt, D. [AREVA Resources Canada AREVA Resources Canada Inc., Saskatoon, SK (Canada)

    2009-07-01

    The authors propose explanations for the clayey alteration which surrounds uranium deposits related to proterozoic discordances as it is noticed in Canada (Athabasca) and Australia (Kombolgie). The observed mineral sequences are interpreted as the product of an increasing interaction between infiltrated diagenetic acid and oxidising solutions on the one hand, and platform rocks on the other hand, at temperatures between 150 and 200 C. These interpretations are based on crystallographic and crystallochemical investigations

  16. Zircon U-Pb geochronology and geochemistry of granites in the Zhuguangshan complex, South China: Implications for uranium mineralization

    Science.gov (United States)

    Zhang, Long; Chen, Zhenyu; Li, Xiaofeng; Li, Shengrong; Santosh, M.; Huang, Guolong

    2018-05-01

    The Zhuguangshan complex, composed of Caledonian, Indosinian, and Yanshanian granites, and Cretaceous mafic dykes, is one of the most important granite-hosted uranium producers in South China. Here we present LA-ICP-MS zircon U-Pb and hornblende 40Ar/39Ar geochronology and whole-rock and biotite geochemistry for the granites in this complex to evaluate the magmatism and its constraints on uranium mineralization. Samples collected from the Fuxi, Youdong, Longhuashan, Chikeng, Qiling, and Sanjiangkou intrusions yield zircon weighted 206Pb/238U ages of 426.7 ± 5.4 Ma, 226.4 ± 3.5 Ma, 225.0 ± 2.7 Ma, 152.2 ± 3.0 Ma, 153.9 ± 2.1 Ma, and 155.2 ± 2.1 Ma, respectively. A new Ar-Ar dating of the hornblende of the diabase from the Changjiang uranium ore field yields a plateau age of 145.1 ± 1.5 Ma. These results coupled with published geochronological data indicate that six major magmatic events occurred in the study area at 420-435 Ma, 225-240 Ma, 150-165 Ma, 140 Ma, 105 Ma, and 90 Ma. Both U-bearing and barren granites occur in this complex, and they display differences in whole-rock and biotite geochemistry. The barren granites show higher Al2O3, CaO, TFMM, Rb, Zr, Ba, SI, Mg#, (La/Yb)N, and Eu/Eu*, but lower SiO2, ALK, Rb, DI, Rb/Sr, and TiO2/MgO than those of the U-bearing granites. Biotites in the U-bearing granites are close to the Fe-rich siderophyllite-annite end member with Fe/(Fe + Mg) ratios higher than 0.66, whereas those in the barren granites are relatively close to the Mg-rich eastonite-phlogopite end member with Fe/(Fe + Mg) ratios uranium ore potential of the granites in the Zhuguangshan complex. The geochemical variations of U-bearing and barren granites can serve as a potential detector for granite-hosted uranium deposits.

  17. Minerals Yearbook, volume I, Metals and Minerals

    Science.gov (United States)

    ,

    2018-01-01

    The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

  18. Laboratory of minerals purification

    International Nuclear Information System (INIS)

    2002-01-01

    The laboratory of minerals purification was organized in 1962 where with application of modern physical and chemical methods were investigated the mechanism of flotation reagents interaction with minerals' surface, was elaborated technologies on rising complexity of using of republic's minerals

  19. Mineralization and defluoridation of 2,2,3,3-tetrafluoro -1-propanol (TFP) by UV oxidation in a novel three-phase fluidized bed reactor (3P-FBR).

    Science.gov (United States)

    Shih, Yu-Jen; Tsai, Meng-Tso; Huang, Yao-Hui

    2013-05-01

    2,2,3,3-Tetrafluoro-1-propanol (TFP, C3H4F4O, M.W. = 132.06) is extensively used as the solvent in CD-R and DVD-R fabrication. Since it has a fluorinated alky-chain configuration and is non-biodegradable, its treatment by conventional oxidation methods is typically very inefficient. In this work, novel three-phase fluidized bed reactor (3P-FBR, 7.5 cm in diameter, 50 cm high) that combines photo oxidation (UV/H2O2, one of AOPs (Advanced Oxidation Process) and adsorption (BT5 iron oxide as adsorbent) processes is designed for mineralizing and defluorinizing TFP wastewater. The experimental results reveal that TFP can be efficiently mineralized, and the BT5 that is circulated by aeration in the 3P-FBR system can remove the released fluoride ions in the reaction period. Irradiation with 254 nm UV and a 10 mM H2O2 dose yield a TOC removal of TFP (1.39 mM, equivalent to an initial TOC of 50 ppm) of over 99.95% in 2 h, and 99% of fluoride was removed by BT5 with an adsorption capacity of 24.1 mg-F g(-1). Copyright © 2013 Elsevier Ltd. All rights reserved.

  20. South Africa's mineral industry

    International Nuclear Information System (INIS)

    1985-06-01

    The main aim of the Minerals Bureau in presenting this annual review is to provide an up-to-date reference document on the current state of the mineral industry in South Africa. This includes a brief look at the production, trade, economy, resources and deposits of precious metals and minerals, energy minerals, metallic minerals, and non-metallic minerals. One article discusses the production, trade, export, deposits and economy of uranium

  1. Miscellaneous Industrial Mineral Operations

    Data.gov (United States)

    Department of Homeland Security — This map layer includes miscellaneous industrial minerals operations in the United States. The data represent commodities covered by the Minerals Information Team...

  2. Minerals from Macedonia: XV. Sivec mineral assemble

    International Nuclear Information System (INIS)

    Boev, Blazho; Jovanovski, Gligor; Makreski, Petre; Bermanec, Vladimir

    2005-01-01

    The paper presents investigations carried out on the collected minerals from the Sivec deposit. It is situated in the vicinity of the town of Prilep, representing a rare occurrence of sugary white dolomite marbles. The application of suitable methods of exploitation of decorative-dimension stones makes possible to obtain large amounts of commercial blocks well known in the world. Despite the existence of dolomite marbles, a series of exotic minerals are typical in Sivec mineralization. Among them, the most significant are: calcite, fluorite, rutile, phlogopite, corundum, diaspore, almandine, kosmatite (clintonite or margarite), clinochlore, muscovite, quartz, pyrite, tourmaline and zoisite. An attempt to identify ten collected minerals using the FT IR spectroscopy is performed. The identification of the minerals was based on the comparison of the infrared spectra of our specimens with the corresponding literature data for the mineral species originating all over the world. The coloured pictures of all studied silicate minerals are presented as well. (Author)

  3. Develop of analytic method for the determination of vitamin D3 in multivitaminics and minerals using chromatography it liquidates of high efficiency in normal phase with ultraviolet detection

    International Nuclear Information System (INIS)

    Solis Barrantes, J. A.

    1999-01-01

    The good chromatography conditions settled down for the determination vitamin D 3 in multivitaminic samples by means of the analytic technique of chromatography it liquidates of high efficiency (HPLC) in normal phase, with ultraviolet detection to 265 nm. The best conditions in the proposed methodology settled down and the variables of analytic acting were validated, for the analytic quantification of vitamin D 3 in International units. The applicability of the methodology was demonstrated in the vitamin determination D 3 in multivitaminis samples in pill form [es

  4. Growth Performance, Carcass Characteristics and Plasma Mineral Chemistry as Affected by Dietary Chloride and Chloride Salts Fed to Broiler Chickens Reared under Phase Feeding System

    Directory of Open Access Journals (Sweden)

    M. M. H. Mushtaq

    2013-06-01

    Full Text Available Requirements of dietary chloride (dCl and chloride salts were determined by using 4×2 factorial arrangement under four phase feeding program. Four levels (0.31, 0.45, 0.59 and 0.73% and two sources (NH4Cl and CaCl2 of the dCl were allocated to 1,472 chicks in eight dietary treatments in which each treatment was replicated four times with 46 birds per replicate. The four phase feeding program was comprised of four dietary phases: Prestarter (d 1 to 10, Starter (d 11 to 20, Grower (d 21 to 33 and Finisher (d 34 to 42; and diets were separately prepared for each phase. The cations, anions, pH, dissolved oxygen (DO, temperature, electrical conductivity (EC, total dissolved solids (TDS and salinity were analyzed in drinking water and were not affected by dietary treatments. BW gain (BWG; p≤0.009 and feed:gain (FG; p≤0.03 were improved in CaCl2 supplemented diets during d 1 to 10. The maximum response of BWG and FG was observed at 0.38% and 0.42% dCl, respectively, for d 34 to 42. However, the level of dCl for BWG during d 21 to 33 (p≤0.04 and d 34 to 42 (p≤0.009 was optimized at 0.60% and 0.42%, respectively. The level of dCl for optimized feed intake (FI; p≤0.006, FG (p≤0.007 and litter moisture (LM; p≤0.001 was observed at 0.60%, 0.38% and 0.73%, respectively, for d 1 to 42. Water intake (DWI was not affected by increasing dCl supplementation (p>0.05; however, the ratio between DWI and FI (DWI:FI was found highest at 0.73% dCl during d 1 to 10 (p≤0.05 and d 21 to 33 (p≤0.009. Except for d 34 to 42 (p≤0.006, the increasing level of dCl did not result in a significant difference in mortality during any phase. Blood pH and glucose, and breast and thigh weights (percentage of dressed weight were improved while dressing percentage (DP and gastrointestinal health were exacerbated with NH4Cl as compared to CaCl2 supplemented diets (p≤0.001. Higher plasma Na+ and HCO3− and lower Cl− and Ca++ were observed in NH4Cl supplemented

  5. Effects of Bacterial Siderophore and Biofilm Synthesis on Silicate Mineral Dissolution Kinetics: Results from Experiments with Targeted Mutants

    Science.gov (United States)

    Van Den Berghe, M. D.; West, A. J.; Nealson, K. H.

    2018-05-01

    This project aims to characterize and quantify the specific microbial mechanisms and metabolic pathways responsible for silicate mineral dissolution and micronutrient acquisition directly from mineral phases.

  6. The behavior during water-mineral interaction of britholite, an analogue of an apatite structured potential long-term actinide host phase

    Energy Technology Data Exchange (ETDEWEB)

    Chairat, C.; Oelkers, E.H.; Schott, J.; Harouiya, N.; Lartigue, J-E.; Guy, C.; Audubert, F

    2004-07-01

    Neodymium britholite (Ca{sub 9}Nd(PO{sub 4}){sub 5}SiO{sub 2}F{sub 2}) dissolution rates have been studied because it is an analogue for potential actinide waste hosts; it is believed that the behavior of Nd is representative of that of the actinide elements. Steady-state dissolution rates of britholite were measured in closed and open system reactors as a function of aqueous solution composition at 25 to 90 deg C. Measured britholite dissolution rates based on Ca, P, and F release are found to be close to corresponding apatite dissolution rates; these rates at 25 deg C decrease from 10-8 to 10-11 mol/m{sup 2}/s with increasing pH from 4 to 12. Measured Nd release rates are far slower than those of these other elements; Nd concentrations in solution appear to be in equilibrium with NdPO{sub 4}, which limits aqueous Nd concentrations to less than 10-12 mol/kg at near neutral conditions. By analogy, it appears likely that aqueous actinide release from analogous waste hosts will be similarly limited by the precipitation of sparingly soluble AcPO{sub 4} phases. (authors)

  7. Mineral distributions at the developing tendon enthesis.

    Science.gov (United States)

    Schwartz, Andrea G; Pasteris, Jill D; Genin, Guy M; Daulton, Tyrone L; Thomopoulos, Stavros

    2012-01-01

    Tendon attaches to bone across a functionally graded interface, "the enthesis". A gradient of mineral content is believed to play an important role for dissipation of stress concentrations at mature fibrocartilaginous interfaces. Surgical repair of injured tendon to bone often fails, suggesting that the enthesis does not regenerate in a healing setting. Understanding the development and the micro/nano-meter structure of this unique interface may provide novel insights for the improvement of repair strategies. This study monitored the development of transitional tissue at the murine supraspinatus tendon enthesis, which begins postnatally and is completed by postnatal day 28. The micrometer-scale distribution of mineral across the developing enthesis was studied by X-ray micro-computed tomography and Raman microprobe spectroscopy. Analyzed regions were identified and further studied by histomorphometry. The nanometer-scale distribution of mineral and collagen fibrils at the developing interface was studied using transmission electron microscopy (TEM). A zone (∼20 µm) exhibiting a gradient in mineral relative to collagen was detected at the leading edge of the hard-soft tissue interface as early as postnatal day 7. Nanocharacterization by TEM suggested that this mineral gradient arose from intrinsic surface roughness on the scale of tens of nanometers at the mineralized front. Microcomputed tomography measurements indicated increases in bone mineral density with time. Raman spectroscopy measurements revealed that the mineral-to-collagen ratio on the mineralized side of the interface was constant throughout postnatal development. An increase in the carbonate concentration of the apatite mineral phase over time suggested possible matrix remodeling during postnatal development. Comparison of Raman-based observations of localized mineral content with histomorphological features indicated that development of the graded mineralized interface is linked to endochondral

  8. United States mineral resources

    Science.gov (United States)

    Brobst, Donald A.; Pratt, Walden P.

    1973-01-01

    mineral-resource estimates and public policy. In the third chapter, R. L. Erickson discusses some new points of view on the relation of reserves and resources to the crustal abundance of elements. We acknowledge with thanks the cooperation of our colleagues in all phases of the preparation of this volume. Whatever success the book may attain is due entirely to a total effort. A paragraph of acknowledgment originally submitted as a part of the chapter on "Nuclear fuels" is given here instead because we feel it applied to all chapters: "The writers have drawn freely from published information, not all of which is cited, and from their colleagues, none of whom are given specific credit. The reader should be aware that the paper could not have been written without these sources." We extend specific thanks to Michael Fleischer for preparation of summaries of geochemical information that are included in many chapters. 

  9. Construction Minerals Operations

    Data.gov (United States)

    Department of Homeland Security — This map layer includes construction minerals operations in the United States. The data represent commodities covered by the Minerals Information Team (MIT) of the...

  10. Agricultural Minerals Operations

    Data.gov (United States)

    Department of Homeland Security — This map layer includes agricultural minerals operations in the United States. The data represent commodities covered by the Minerals Information Team (MIT) of the...

  11. Mineral commodity summaries 2015

    Science.gov (United States)

    ,

    2015-01-01

    Each chapter of the 2015 edition of the U.S. Geological Survey (USGS) Mineral Commodity Summaries (MCS) includes information on events, trends, and issues for each mineral commodity as well as discussions and tabular presentations on domestic industry structure, Government programs, tariffs, 5-year salient statistics, and world production and resources. The MCS is the earliest comprehensive source of 2014 mineral production data for the world. More than 90 individual minerals and materials are covered by two-page synopses.

  12. Chitosan: collagen sponges. In vitro mineralization

    International Nuclear Information System (INIS)

    Martins, Virginia da C.A.; Silva, Gustavo M.; Plepis, Ana Maria G.

    2011-01-01

    The regeneration of bone tissue is a problem that affects many people and scaffolds for bone tissue growth has been widely studied. The aim of this study was the in vitro mineralization of chitosan, chitosan:native collagen and chitosan:anionic collagen sponges. The sponges were obtained by lyophilization and mineralization was made by soaking the sponges in alternating solutions containing Ca 2+ and PO 4 3- . The mineralization was confirmed by infrared spectroscopy, energy dispersive X-ray and X-ray diffraction observing the formation of phosphate salts, possibly a carbonated hydroxyapatite since Ca/P=1.80. The degree of mineralization was obtained by thermogravimetry calculating the amount of residue at 750 deg C. The chitosan:anionic collagen sponge showed the highest degree of mineralization probably due to the fact that anionic collagen provides additional sites for interaction with the inorganic phase. (author)

  13. [Bone Cell Biology Assessed by Microscopic Approach. Bone mineralization by ultrastructural imaging].

    Science.gov (United States)

    Hasegawa, Tomoka

    2015-10-01

    Bone mineralization can be divided into two phases ; one is primary mineralization associated with osteoblastic bone formation, and the other is secondary mineralization which gradually increases mineral density of bone matrix after the primary mineralization. Primary mineralization is initiated by matrix vesicles synthesized by mature osteoblasts. Crystalline calcium phosphates are nucleated inside these matrix vesicles, and then, get out of them forming spherical mineralized nodule, which can grow more by being supplied with Ca2+ and PO4(3-) (matrix vesicle mineralization). Thereafter, the mineralized nodules make contacts with surrounding collagen fibrils, extending mineralization along with their longitudinal axis from the contact points (collagen mineralization). In this review, the ultrastructural findings on bone mineralization, specially, primary mineralization will be provided.

  14. Sulfide Mineral Surfaces

    International Nuclear Information System (INIS)

    Rosso, Kevin M.; Vaughan, David J.

    2006-01-01

    The past twenty years or so have seen dramatic development of the experimental and theoretical tools available to study the surfaces of solids at the molecular (?atomic resolution?) scale. On the experimental side, two areas of development well illustrate these advances. The first concerns the high intensity photon sources associated with synchrotron radiation; these have both greatly improved the surface sensitivity and spatial resolution of already established surface spectroscopic and diffraction methods, and enabled the development of new methods for studying surfaces. The second centers on the scanning probe microscopy (SPM) techniques initially developed in the 1980's with the first scanning tunneling microscope (STM) and atomic force microscope (AFM) experiments. The direct 'observation' of individual atoms at surfaces made possible with these methods has truly revolutionized surface science. On the theoretical side, the availability of high performance computers coupled with advances in computational modeling has provided powerful new tools to complement the advances in experiment. Particularly important have been the quantum mechanics based computational approaches such as density functional theory (DFT), which can now be easily used to calculate the equilibrium crystal structures of solids and surfaces from first principles, and to provide insights into their electronic structure. In this chapter, we review current knowledge of sulfide mineral surfaces, beginning with an overview of the principles relevant to the study of the surfaces of all crystalline solids. This includes the thermodynamics of surfaces, the atomic structure of surfaces (surface crystallography and structural stability, adjustments of atoms at the surface through relaxation or reconstruction, surface defects) and the electronic structure of surfaces. We then discuss examples where specific crystal surfaces have been studied, with the main sulfide minerals organized by structure type

  15. Sulfide Mineral Surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Rosso, Kevin M.; Vaughan, David J.

    2006-08-01

    The past twenty years or so have seen dramatic development of the experimental and theoretical tools available to study the surfaces of solids at the molecular (?atomic resolution?) scale. On the experimental side, two areas of development well illustrate these advances. The first concerns the high intensity photon sources associated with synchrotron radiation; these have both greatly improved the surface sensitivity and spatial resolution of already established surface spectroscopic and diffraction methods, and enabled the development of new methods for studying surfaces. The second centers on the scanning probe microscopy (SPM) techniques initially developed in the 1980's with the first scanning tunneling microscope (STM) and atomic force microscope (AFM) experiments. The direct 'observation' of individual atoms at surfaces made possible with these methods has truly revolutionized surface science. On the theoretical side, the availability of high performance computers coupled with advances in computational modeling has provided powerful new tools to complement the advances in experiment. Particularly important have been the quantum mechanics based computational approaches such as density functional theory (DFT), which can now be easily used to calculate the equilibrium crystal structures of solids and surfaces from first principles, and to provide insights into their electronic structure. In this chapter, we review current knowledge of sulfide mineral surfaces, beginning with an overview of the principles relevant to the study of the surfaces of all crystalline solids. This includes the thermodynamics of surfaces, the atomic structure of surfaces (surface crystallography and structural stability, adjustments of atoms at the surface through relaxation or reconstruction, surface defects) and the electronic structure of surfaces. We then discuss examples where specific crystal surfaces have been studied, with the main sulfide minerals organized by

  16. OPAQUE MINERAL CONTENT OF DUTLUCA VOLCANICS (BURHANİYE - BALIKESİR: THE EFFECT OF HYDROTHERMAL ALTERATION ON THESE MINERALS

    Directory of Open Access Journals (Sweden)

    Şükrü KOÇ

    2016-12-01

    Full Text Available Dutluca volcanics, which are known as Hallaçlar Formation in regional scale in the study area (Kurshens- ky, 1976, are composed of hydrothermally altered andesite and basaltic andesite. In these rocks, sulfidic minerals such as pyrite, enargite and chalcosine, and oxide and hydroxide minerals such as magnetite, hematite and goethite were detected as opaque minerals. The presence of enargite in opaque mineral para- genesis, and the changes observed in structures and textures of opaque and silicate minerals indicate that examined volcanics have been altered by highly sulfidic hydrothermal solutions. During the hydrothermal alteration process, which indicates at least in two phases, a diffuse pyritization rich in H S in reducing conditions and enargite mineral, which is known as pathfinder minerals in such processes, formed in the first phase. Later on; the extensive martitization developed in oxidizing conditions.

  17. Grouping Minerals by Their Formulas

    Science.gov (United States)

    Mulvey, Bridget

    2018-01-01

    Minerals are commonly taught in ways that emphasize mineral identification for its own sake or maybe to help identify rocks. But how do minerals fit in with other science content taught? The author uses mineral formulas to help Earth science students wonder about the connection between elements, compounds, mixtures, minerals, and mineral formulas.…

  18. The mineral matter characteristics of some Chinese coal

    Energy Technology Data Exchange (ETDEWEB)

    Liu, X. [China University of Mining and Technology (China). Dept. of Coal Preparation and Utilization

    1994-12-01

    The mineral matter has been separated from 18 coal samples with a low temperature ashes and analyzed by means of X-ray diffraction method. Based on the results of chemical analysis of the coal ash, with reference to the standard composition of minerals, the content of various mineral phases in the coal ash has been determined. Furthermore, this paper summarizes the mineral matter characteristics of the coal samples and discusses the relationship between the composition of mineral matter in coal and its depositional environment.

  19. 43 CFR 19.8 - Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest...

    Science.gov (United States)

    2010-10-01

    ... patents, and mineral leasing within National Forest Wilderness. 19.8 Section 19.8 Public Lands: Interior... § 19.8 Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest... locations, mineral patents, and mineral leasing within National Forest Wilderness are contained in parts...

  20. Radioactive mineral deposits

    Energy Technology Data Exchange (ETDEWEB)

    1948-01-01

    This publication was designed as a guide for uranium and thorium prospectors in Australia. Physical properties, such as color, streak, luster, hardness, fracture, and specific gravity of the uranium and thorium-bearing minerals are summarized and the various methods suitable for detecting radioactivity in minerals are described. Two colored plates show samples of pitchblende (uraninite), autunite, carnotite, monazite, and others of the most important minerals sources of uranium and thorium.

  1. Brazilian minerals annual report

    International Nuclear Information System (INIS)

    1977-01-01

    Statistics of Brazilian mineral resources and production in 1977 are presented. Data included refer also to economic aspects, market, taxes, government incentives, manpower, exportation, importation, etc [pt

  2. Minerals industry survey, 1984

    Energy Technology Data Exchange (ETDEWEB)

    1984-01-01

    This is the seventh edition of the statistical survey commissioned by the Australian Mining Industry Council. It represents the most comprehensive review of the financial position of the Australian minerals industry and provides timely financial data on the minerals industry. The tables of this survey have been prepared for AMIC by Coopers and Lybrand, Chartered Accountants, based on information supplied to them in confidence by the respondent companies. For the purpose of the survey, the minerals industry has been defined as including exploration for, and extraction and primary processing of, minerals in Australia. The oil and gas industry is not included.

  3. Reagan issues mineral policy

    Science.gov (United States)

    The National Materials and Minerals Program plan and report that President Reagan sent to Congress on April 5 aims to ‘decrease America's minerals vulnerability’ while reducing future dependence on potentially unstable foreign sources of minerals. These goals would be accomplished by taking inventory of federal lands to determine mineral potential; by meeting the stockpile goals set by the Strategic and Critical Material Stockpiling Act; and by establishing a business and political climate that would encourage private-sector research and development on minerals.Now that the Administration has issued its plan, the Subcommittee on Mines and Mining of the House Committee on Interior and Insular Affairs will consider the National Minerals Security Act (NMSA), which was introduced 1 year ago by subcommittee chairman Jim Santini (D-Nev.) [Eos, May 19, 1981, p. 497]. The bill calls for establishing a three-member White-House-level council to coordinate the development of a national minerals policy; amending tax laws to assist the mining industry to make capital investments to locate and produce strategic materials; and creating a revolving fund for the sale and purchase of strategic minerals. In addition, the NMSA bill would allow the secretary of the interior to make previously withdrawn public lands available for mineral development. The subcommittee will hold a hearing on the Administration's plan on May 11. Interior Secretary James Watt has been invited to testify.

  4. International mineral economics

    International Nuclear Information System (INIS)

    Gocht, W.R.; Eggert, R.G.

    1988-01-01

    International Mineral Economics provides an integrated overview of the important concepts. The treatment is interdisciplinary, drawing on the fields of economics, geology, business, and mining engineering. Part I examines the technical concepts important for understanding the geology of ore deposits, the methods of exploration and deposit evaluation, and the activities of mining and mineral processing. Part II focuses on the economic and related concepts important for understanding mineral development, the evaluation of exploration and mining projects, and mineral markets and market models. Finally, Part III reviews and traces the historical development of the policies of international organizations, the industrialized countries, and the developing countries. (orig.)

  5. Mineral statistics yearbook 1994

    International Nuclear Information System (INIS)

    1994-01-01

    A summary of mineral production in Saskatchewan was compiled and presented as a reference manual. Statistical information on fuel minerals such as crude oil, natural gas, liquefied petroleum gas and coal, and of industrial and metallic minerals, such as potash, sodium sulphate, salt and uranium, was provided in all conceivable variety of tables. Production statistics, disposition and value of sales of industrial and metallic minerals were also made available. Statistical data on drilling of oil and gas reservoirs and crown land disposition were also included. figs., tabs

  6. Marine Mineral Exploration

    DEFF Research Database (Denmark)

    in EEZ areas are fairly unknown; many areas need detailed mapping and mineral exploration, and the majority of coastal or island states with large EEZ areas have little experience in exploration for marine hard minerals. This book describes the systematic steps in marine mineral exploration....... Such exploration requires knowledge of mineral deposits and models of their formation, of geophysical and geochemical exploration methods, and of data evaluation and interpretation methods. These topics are described in detail by an international group of authors. A short description is also given of marine...

  7. Mineral transformations during the dissolution of uranium ore minerals by dissimilatory metal-reducing bacteria

    Science.gov (United States)

    Glasauer, S.; Weidler, P.; Fakra, S.; Tyliszczak, T.; Shuh, D.

    2011-12-01

    Carnotite minerals [X2(UO2)2(VO4)2]; X = K, Ca, Ba, Mn, Na, Cu or Pb] form the major ore of uranium in the Colorado Plateau. These deposits are highly oxidized and contain U(VI) and V(IV). The biotransformation of U(VI) bound in carnotite by bacteria during dissimilatory metal reduction presents a complex puzzle in mineral chemistry. Both U(VI) and V(V) can be respired by metal reducing bacteria, and the mineral structure can change depending on the associated counterion. We incubated anaerobic cultures of S. putrefaciens CN32 with natural carnotite minerals from southeastern Utah in a nutrient-limited defined medium. Strain CN32 is a gram negative bacterium and a terrestrial isolate from New Mexico. The mineral and metal transformations were compared to a system that contained similar concentrations of soluble U(VI) and V(V). Electron (SEM, TEM) microscopies and x-ray spectromicroscopy (STXM) were used in conjunction with XRD to track mineral changes, and bacterial survival was monitored throughout the incubations. Slow rates of metal reduction over 10 months for the treatment with carnotite minerals revealed distinct biotic and abiotic processes, providing insight on mineral transformation and bacteria-metal interactions. The bacteria existed as small flocs or individual cells attached to the mineral phase, but did not adsorb soluble U or V, and accumulated very little of the biominerals. Reduction of mineral V(V) necessarily led to a dismantling of the carnotite structure. Bioreduction of V(V) by CN32 contributed small but profound changes to the mineral system, resulting in new minerals. Abiotic cation exchange within the carnotite group minerals induced the rearrangement of the mineral structures, leading to further mineral transformation. In contrast, bacteria survival was poor for treatments with soluble U(VI) and V(V), although both metals were reduced completely and formed solid UO2 and VO2; we also detected V(III). For these treatments, the bacteria

  8. Adsorption of dextrin on hydrophobic minerals.

    Science.gov (United States)

    Beaussart, Audrey; Mierczynska-Vasilev, Agnieszka; Beattie, David A

    2009-09-01

    The adsorption of dextrin on talc, molybdenite, and graphite (three naturally hydrophobic minerals) has been compared. Adsorption isotherms and in situ tapping mode atomic force microscope (TMAFM) imaging have enabled polymer adsorbed amount and morphology of the adsorbed layer (area coverage and polymer domain size) to be determined and also the amount of hydration water in the structure of the adsorbed layer. The effect of the polymer on the mineral contact angles, measured by the captive bubble method on cleaved mineral surfaces, indicates clear correlations between the hydrophobicity reduction of the minerals, the adsorbed amount, and the surface coverage of the adsorbed polymer. Predictions of the flotation recovery of the treated mineral phases have been confirmed by performing batch flotation experiments. The influence of the polymer surface coverage on flotation recovery has highlighted the importance of this key parameter in the predictions of depressant efficiency. The roles of the initial hydrophobicity and the surface structure of the mineral basal plane in determining adsorption parameters and flotation response of the polymer-treated minerals are also discussed.

  9. Impact of mineral transformation on elemental mobility in aquatic environments

    International Nuclear Information System (INIS)

    Waite, T.D.; Payne, T.E.; Davis, J.A.

    1994-01-01

    While laboratory and field studies of uranium uptake on naturally occurring mineral substrates have indicated that interaction with amorphous oxide phases controls the steady state concentration of uranium in the dissolved phase, questions remain concerning the impact of crystallization of these amorphous phases on ability of the minerals to retain adsorbed uranium. Using isotope exchange techniques, the authors confirm that a portion of the adsorbed uranium is retained within the mineral structure on increasing crystallization. In addition, the relationship between increased crystallinity, decreased site density and lowered elemental uptake is discussed, with uranium partitioning to the solids of varying crystallinity successfully modelled using the surface complexation approach

  10. Mineral oil industry

    NARCIS (Netherlands)

    Brasser, L.J.; Suess, M.J.; Grefen, K.; Reinisch, D.W.

    1985-01-01

    In this chapter a general picture is presented of the air pollution aspects in the mineral oil industry. The complete field is covered, starting from drilling operations and the well head up to the delivery of the products to the consumer. A large field of activities as is given by the mineral oil

  11. Vitamins, Minerals, and Mood

    Science.gov (United States)

    Kaplan, Bonnie J.; Crawford, Susan G.; Field, Catherine J.; Simpson, J. Steven A.

    2007-01-01

    In this article, the authors explore the breadth and depth of published research linking dietary vitamins and minerals (micronutrients) to mood. Since the 1920s, there have been many studies on individual vitamins (especially B vitamins and Vitamins C, D, and E), minerals (calcium, chromium, iron, magnesium, zinc, and selenium), and vitamin-like…

  12. Mineral commodity summaries 2018

    Science.gov (United States)

    Ober, Joyce A.

    2018-01-31

    This report is the earliest Government publication to furnish estimates covering 2017 nonfuel mineral industry data. Data sheets contain information on the domestic industry structure, Government programs, tariffs, and 5-year salient statistics for more than 90 individual minerals and materials.

  13. Indochina area mineral prospects

    Energy Technology Data Exchange (ETDEWEB)

    1990-10-05

    Prospects for commercial mining of various minerals are considered for Kampuchea (Cambodia), Laos, Vietnam, Myanmar (Burma) and Thailand. Mineral production is much below its geologic potential for economic and political reasons. Resource potential is limited to tin, tungsten, lead and zinc, barytes and gemstones, and coal. 1 fig.

  14. Taxation of unmined minerals

    International Nuclear Information System (INIS)

    Bremberg, B.P.

    1989-01-01

    This paper reports on the Kentucky Revenue Cabinet which began implementing its controversial unmined minerals tax program. The Revenue Cabinet should complete its first annual assessment under this program in December, 1989. The Revenue Cabinet's initial efforts to collect basic data concerning the Commonwealth's coal bearing lands has yielded data coverage for 5 million of Kentucky's 10 million acres of coal lands. Approximately 1000 detailed information returns have been filed. The returns will be used to help create an undeveloped mineral reserves inventory, determine mineral ownership, and value mineral reserves. This new program is run by the Revenue Cabinet's Mineral Valuation Section, under the Division of Technical Support, Department of Property Taxation. It has been in business since September of 1988

  15. Mineral industry in Australia

    International Nuclear Information System (INIS)

    Parbo, S.A.

    1982-01-01

    The paper reviews the history and growth of the mineral industry in Australia and its significance to the nation's economic growth and overseas trade, particularly over the last twenty years during which time production of coal, iron ore, manganese and mineral sands has increased greatly and new discoveries of petroleum, bauxite and nickel have given rise to major new industries. Australia ranks fourteenths in the value of world trade and is among the world's largest exporters of alumina, iron ore, mineral sands, coal, lead, zinc and nickel. Some details of production, processing and exports of the major minerals are given. Comment is made on the policies and roles of the six State Governments and the Federal Government in respect of ownership and control of the mining, processing and exporting of both energy and non-energy minerals. (orig.) [de

  16. Biologically controlled minerals as potential indicators of life

    Science.gov (United States)

    Schwartz, D. E.; Mancinelli, R. L.; Kaneshiro, E.

    1991-01-01

    Minerals can be produced and deposited either by abiotic or biologic means. Regardless of their origin, mineral crystals reflect the environment conditions (e.g., temperature, pressure, chemical composition, and redox potential) present during crystal formation. Biologically-produced mineral crystals are grown or reworked under the control of their host organism and reflect an environment different from the abiotic environment. In addition, minerals of either biologic or abiotic origin have great longevities. For these reasons, biologically produced minerals have been proposed as biomarkers. Biomarkers are key morphological, chemical, and isotopic signatures of living systems that can be used to determine if life processes have occurred. Studies of biologically controlled minerals produced by the protist, Paramecium tetraurelia, were initiated since techniques have already been developed to culture them and isolate their crystalline material, and methods are already in place to analyze this material. Two direct crystalline phases were identified. One phase, whose chemical composition is high in Mg, was identified as struvite. The second phase, whose chemical composition is high in Ca, has not been previously found occurring naturally and may be considered a newly discovered material. Analyses are underway to determine the characteristics of these minerals in order to compare them with characteristics of these minerals in order to compare them with characteristics of minerals formed abiotically, but with the same chemical composition.

  17. Influence of oil and mineral characteristics on oil-mineral interaction

    International Nuclear Information System (INIS)

    Wood, P.A.; Lunel, T.; Daniel, F.; Swannell, R.; Lee, K.; Stoffyn-Egli, P.

    1998-01-01

    A laboratory study was conducted to simulate the process of oil-mineral interaction in seawater. Thirteen different crudes, emulsions and oil products were used in the study. The objective was to improve the fundamental understanding of the characteristics of oils and minerals that influence the process. The findings of an initial phase of studies based on the swirling flask and marine simulation procedures were also described. Oil content associated with flocs to oil and mineral characteristics were discussed. Emulsions were prepared at 10 degrees C by vigorously mixing the oil with excess artificial seawater in a Kilner jar using a high shear homogenizer. Topped oils were prepared by distillation to 250 degrees C. The biodegraded oil was prepared from the topped crude oil. Biodegradation was achieved over a 28 day period using natural seawater and naturally occurring hydrocarbon degraders. The relationships between oil concentration, oil density and mineral exchange capacity were determined. The study showed that greater oil concentrations in the water column could be expected with (1) the presence of mineral fines, (2) minerals with greater cation exchange rates, (3) minerals with finer sizes, and (4) oils of lower viscosity and density. It was determined that in coastal waters the viscosity of the oil/emulsion will likely be the main factor affecting oil-mineral interactions. The viscosity limit for allowing oil fines interaction is likely to be dependent on the energy in the coastal zone affected by the oil pollution. 18 refs., 5 tabs., 13 figs

  18. Mineral facilities of Europe

    Science.gov (United States)

    Almanzar, Francisco; Baker, Michael S.; Elias, Nurudeen; Guzman, Eric

    2010-01-01

    This map displays over 1,700 records of mineral facilities within the countries of Europe and western Eurasia. Each record represents one commodity and one facility type at a single geographic location. Facility types include mines, oil and gas fields, and plants, such as refineries, smelters, and mills. Common commodities of interest include aluminum, cement, coal, copper, gold, iron and steel, lead, nickel, petroleum, salt, silver, and zinc. Records include attributes, such as commodity, country, location, company name, facility type and capacity (if applicable), and latitude and longitude geographical coordinates (in both degrees-minutes-seconds and decimal degrees). The data shown on this map and in table 1 were compiled from multiple sources, including (1) the most recently available data from the U.S. Geological Survey (USGS) Minerals Yearbook (Europe and Central Eurasia volume), (2) mineral statistics and information from the USGS Minerals Information Web site (http://minerals.usgs.gov/minerals/pubs/country/europe.html), and (3) data collected by the USGS minerals information country specialists from sources, such as statistical publications of individual countries, annual reports and press releases of operating companies, and trade journals. Data reflect the most recently published table of industry structure for each country at the time of this publication. Additional information is available from the country specialists listed in table 2.

  19. Definitions of Health Terms: Minerals

    Science.gov (United States)

    ... gov/definitions/mineralsdefinitions.html Definitions of Health Terms : Minerals To use the sharing features on this page, ... National Institutes of Health, Office of Dietary Supplements Minerals Minerals are those elements on the earth and ...

  20. Minerals industry survey 1987

    Energy Technology Data Exchange (ETDEWEB)

    1987-01-01

    This is the eleventh Minerals Industry Survey produced by the Australian Mining Industry Council. It represents an invaluable time series on the minerals industry's financial performance, as well as an up to date description of the industry for the latest financial year. The survey has been conceived as a supplement to and expansion of the various Australian Bureau of Statistics and Bureau of Mineral Resources, Geology and Geophysics publications which describe the exploration, mining and smelting and refining industries in Australia. The tables in this survey have been prepared by Coopers and Lybrand, Chartered Accountants, based on information supplied to them in confidence by the respondent companies.

  1. Characterization of clay minerals

    International Nuclear Information System (INIS)

    Diaz N, C.; Olguin, M.T.; Solache R, M.; Alarcon H, T.; Aguilar E, A.

    2002-01-01

    The natural clays are the more abundant minerals on the crust. They are used for making diverse industrial products. Due to the adsorption and ion exchange properties of these, a great interest for developing research directed toward the use of natural clays for the waste water treatment has been aroused. As part of such researches it is very important to carry out previously the characterization of the interest materials. In this work the results of the mineral and elemental chemical composition are presented as well as the morphological characteristics of clay minerals from different regions of the Mexican Republic. (Author)

  2. Hydrothermal Gold Mineralization and Structural Controls near May ...

    African Journals Online (AJOL)

    Mickiale

    Structural data suggests four phases of deformations and NE-SW trending foliation is ... Hawzein area and reported presence of hydrothermal gold and base metal ..... coarse mafic and plagioclase minerals in fine grained ground mass matrix ...

  3. Law of radioactive minerals

    International Nuclear Information System (INIS)

    1980-01-01

    Legal device done in order to standardize and promote the exploration and explotation of radioactive minerals by peruvian and foreign investors. This device include the whole process, since the prospection until the development, after previous auction given by IPEN

  4. Mineral Commodity Summaries 2009

    Science.gov (United States)

    ,

    2009-01-01

    Each chapter of the 2009 edition of the U.S. Geological Survey (USGS) Mineral Commodity Summaries (MCS) includes information on events, trends, and issues for each mineral commodity as well as discussions and tabular presentations on domestic industry structure, Government programs, tariffs, 5-year salient statistics, and world production and resources. The MCS is the earliest comprehensive source of 2008 mineral production data for the world. More than 90 individual minerals and materials are covered by two-page synopses. For mineral commodities for which there is a Government stockpile, detailed information concerning the stockpile status is included in the two-page synopsis. Because specific information concerning committed inventory was no longer available from the Defense Logistics Agency, National Defense Stockpile Center, that information, which was included in earlier Mineral Commodity Summaries publications, has been deleted from Mineral Commodity Summaries 2009. National reserves and reserve base information for most mineral commodities found in this report, including those for the United States, are derived from a variety of sources. The ideal source of such information would be comprehensive evaluations that apply the same criteria to deposits in different geographic areas and report the results by country. In the absence of such evaluations, national reserves and reserve base estimates compiled by countries for selected mineral commodities are a primary source of national reserves and reserve base information. Lacking national assessment information by governments, sources such as academic articles, company reports, common business practice, presentations by company representatives, and trade journal articles, or a combination of these, serve as the basis for national reserves and reserve base information reported in the mineral commodity sections of this publication. A national estimate may be assembled from the following: historically reported

  5. sequenceMiner algorithm

    Data.gov (United States)

    National Aeronautics and Space Administration — Detecting and describing anomalies in large repositories of discrete symbol sequences. sequenceMiner has been open-sourced! Download the file below to try it out....

  6. Mineral industry statistics 1975

    Energy Technology Data Exchange (ETDEWEB)

    1978-01-01

    Production, consumption and marketing statistics are given for solid fuels (coal, peat), liquid fuels and gases (oil, natural gas), iron ore, bauxite and other minerals quarried in France, in 1975. Also accident statistics are included. Production statistics are presented of the Overseas Departments and territories (French Guiana, New Caledonia, New Hebrides). An account of modifications in the mining field in 1975 is given. Concessions, exploitation permits, and permits solely for prospecting for mineral products are discussed. (In French)

  7. Coastal placer minerals

    Digital Repository Service at National Institute of Oceanography (India)

    Iyer, S.D.; Gujar, A.R.

    to be processed and purified to extract the metal either by sulphate or chloride route. The economical aspects of placer mining would involve the cost to benefit ratio, which would encompass the money Selective sorting has resulted in two distinct sediments... or mineral at the national and international levels. Interestingly, though gold is the most sought metal and the prices per gram keep rising, there are others that are much more costly such as diamond and rare earth metals. Uses of Heavy Minerals...

  8. [Pneumoconiosis in bauxite miners].

    Science.gov (United States)

    Molinini, R; Pesola, M; Digennaro, M A; Carino, M; Nuzzaco, A; Coviello, F

    1985-01-01

    The authors examined a group of 40 miners who were being working at an Apulian bauxite mine, presently inactive. Radiographic findings of pulmonary micronodulation without significant reduction of lung functions were showed in 15 miners. Mineralogical analysis of mine dust samples excluded any presence of more than 1% free silica. As a result of this study hypotheses have been formulated about pathogenesis of this moderated and non-invasive pneumoconiosis, showed in long exposed subjects to low silica content dusts.

  9. Mineral commodity summaries 2013

    Science.gov (United States)

    ,

    2013-01-01

    Each chapter of the 2013 edition of the U.S. Geological Survey (USGS) Mineral Commodity Summaries (MCS) includes information on events, trends, and issues for each mineral commodity as well as discussions and tabular presentations on domestic industry structure, Government programs, tariffs, 5-year salient statistics, and world production and resources. The MCS is the earliest comprehensive source of 2012 mineral production data for the world. More than 90 individual minerals and materials are covered by two-page synopses. For mineral commodities for which there is a Government stockpile, detailed information concerning the stockpile status is included in the two-page synopsis. Abbreviations and units of measure, and definitions of selected terms used in the report, are in Appendix A and Appendix B, respectively. “Appendix C—Reserves and Resources” includes “Part A—Resource/Reserve Classification for Minerals” and “Part B—Sources of Reserves Data.” A directory of USGS minerals information country specialists and their responsibilities is Appendix D. The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the MCS 2013 are welcomed.

  10. Mineral commodity summaries 2014

    Science.gov (United States)

    ,

    2014-01-01

    Each chapter of the 2014 edition of the U.S. Geological Survey (USGS) Mineral Commodity Summaries (MCS) includes information on events, trends, and issues for each mineral commodity as well as discussions and tabular presentations on domestic industry structure, Government programs, tariffs, 5-year salient statistics, and world production and resources. The MCS is the earliest comprehensive source of 2013 mineral production data for the world. More than 90 individual minerals and materials are covered by two-page synopses. For mineral commodities for which there is a Government stockpile, detailed information concerning the stockpile status is included in the two-page synopsis. Abbreviations and units of measure, and definitions of selected terms used in the report, are in Appendix A and Appendix B, respectively. “Appendix C—Reserves and Resources” includes “Part A—Resource/Reserve Classification for Minerals” and “Part B—Sources of Reserves Data.” A directory of USGS minerals information country specialists and their responsibilities is Appendix D. The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the MCS 2014 are welcomed.

  11. The mineral economy of Brazil--Economia mineral do Brasil

    Science.gov (United States)

    Gurmendi, Alfredo C.; Barboza, Frederico Lopes; Thorman, Charles H.

    1999-01-01

    This study depicts the Brazilian government structure, mineral legislation and investment policy, taxation, foreign investment policies, environmental laws and regulations, and conditions in which the mineral industry operates. The report underlines Brazil's large and diversified mineral endowment. A total of 37 mineral commodities, or groups of closely related commodities, is discussed. An overview of the geologic setting of the major mineral deposits is presented. This report is presented in English and Portuguese in pdf format.

  12. Origin and nature of the aluminium phosphate-sulfate minerals (APS associated with uranium mineralization in triassic red-beds (Iberian Range, Spain

    Directory of Open Access Journals (Sweden)

    Marfil, R.

    2013-06-01

    Full Text Available This study focuses on the mineralogical and chemical study of an Aluminium–phosphate–sulphate (APS mineralization that occurs in a clastic sequence from the Triassic (Buntsandstein of the Iberian Range. The deposit is constituted by sandstones, mudstones, and conglomerates with arenaceous matrix, which were deposited in fluvial to shallow-marine environments. In addition to APS minerals, the following diagenetic minerals are present in the clastic sequence: quartz, K-feldspar, kaolinite group minerals, illite, Fe-oxides-hidroxides, carbonate-sulphate cement-replacements and secondary uraniferous minerals. APS minerals were identified and characterized by optical microscopy, X-ray diffraction, scanning electron microscopy, and electron microprobe. Microcrystalline APS crystals occur replacing uraniferous minerals, associated with kaolinite, mica and filling pores, in distal fluvial-to-tidal arkoses-subarkoses. Given their Ca, Sr, and Ba contents, the APS minerals can be defined as a solid solution of crandallite-goyacite-gorceixite (0.53 Ca, 0.46 Sr and 0.01 Ba. The chemical composition, low LREE concentration and Sr > S suggest that the APS mineral were originated during the supergene alteration of the Buntsandstein sandstones due to the presence of the mineralizing fluids which causes the development of U-bearing sandstones in a distal alteration area precipitating from partially dissolved and altered detrital minerals. Besides, the occurrence of dickite associated with APS minerals indicates they were precipitated at diagenetic temperatures (higher than 80ºC, related to the uplifting occurred during the late Cretaceous post-rift thermal stage.Este trabajo se centra en el estudio de los minerales fosfato-sulfato alumínicos (APS que se producenen una secuencia clástica del Triásico (Buntsandstein de la Cordillera Ibérica. El depósito está constituido por areniscas, lutitas y conglomerados con matriz arenosa, que fueron depositados en

  13. Incorporation of uranium in pyrochlore oxides and pressure-induced phase transitions

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, F.X., E-mail: zhangfx@umich.edu [Department of Earth and Environmental Sciences, University of Michigan, Ann Arbor, MI 48109 (United States); Lang, M.; Tracy, C.; Ewing, R.C. [Department of Earth and Environmental Sciences, University of Michigan, Ann Arbor, MI 48109 (United States); Gregg, D.J.; Lumpkin, G.R. [Institute of Materials Engineering, ANSTO, Locked Bag 2001, Kirrawee DC 2232, NSW (Australia)

    2014-11-15

    Uranium-doped gadolinium zirconates with pyrochlore structure were studied at ambient and high-pressure conditions up to 40 GPa. The bonding environment of uranium in the structure was determined by x-ray photoelectron and Raman spectroscopies and x-ray diffraction. The uranium valence for samples prepared in air is mainly U{sup 6+}, but U{sup 4+} is present in pyrochlores fabricated in an argon atmosphere. Rietveld refinement of the XRD pattern suggests that uranium ions in pyrochlores are on the 16d site in 6-fold coordination with oxygen. At pressures greater than 22 GPa, the pyrochlore structure transformed to a cotunnite-type phase. The cotunnite high-pressure phase transformed to a defect fluorite structure on the release of pressure. - Graphical abstract: In U-bearing pyrochlore, U ions mainly occupy the 16d site and replace the smaller Zr{sup 4+}, part of the oxygen will occupy the 8b site, which is empty to most pyrochlores. At pressure of 22 GPa, the pyrochlore lattice is not stable and transforms to a cotunnite-type structure. The high-pressure structure is not stable and transform to a fluorite or back to the pyrochlore structure when pressure is released. - Highlights: • We found that U ions mainly occupy the smaller cation site in U-bearing pyrochlore. • Pyrochlore structure is not stable at pressure of more than 20 GPa. • The quenched sample has a pyrochlore or a disordered fluorite structure.

  14. Au-Pt-Pd-U mineralization in the Coronation Hill-El Sherana region, NT

    International Nuclear Information System (INIS)

    Wyborn, L.

    1992-01-01

    In 1990 BMR's Minerals and Land Use program conducted an geochemical and geophysical survey to provide the best possible basis for estimating the resource potential of the Kakadu Conservation Zone. Combining the old and new data, an integrated model for the deposit types has been developed. Although differing in metal content, all mines and prospects of the Coronation Hill region share similar timing and structural controls, suggesting that they are related to one geochemical system. The presence or absence of U in the Au-Pt-Pd mineralisation appears related to geological differences, primarily in host-rock composition. U-bearing deposits are hosted mainly in carbonaceous shales, although some U is associated with chloritic zones. Deposits lacking U, best developed at Coronation Hill, occur in a broad range of host rocks, including quartz-feldspar porphyry, green tuffaceous shale, diorite, dolomite, and sedimentary breccias. Although seemingly diverse rock types, the common components of these U-poor host units are feldspar and/or carbonate. 1 tab., 3 figs

  15. Microbially mediated mineral carbonation

    Science.gov (United States)

    Power, I. M.; Wilson, S. A.; Dipple, G. M.; Southam, G.

    2010-12-01

    Mineral carbonation involves silicate dissolution and carbonate precipitation, which are both natural processes that microorganisms are able to mediate in near surface environments (Ferris et al., 1994; Eq. 1). (Ca,Mg)SiO3 + 2H2CO3 + H2O → (Ca,Mg)CO3 + H2O + H4SiO4 + O2 (1) Cyanobacteria are photoautotrophs with cell surface characteristics and metabolic processes involving inorganic carbon that can induce carbonate precipitation. This occurs partly by concentrating cations within their net-negative cell envelope and through the alkalinization of their microenvironment (Thompson & Ferris, 1990). Regions with mafic and ultramafic bedrock, such as near Atlin, British Columbia, Canada, represent the best potential sources of feedstocks for mineral carbonation. The hydromagnesite playas near Atlin are a natural biogeochemical model for the carbonation of magnesium silicate minerals (Power et al., 2009). Field-based studies at Atlin and corroborating laboratory experiments demonstrate the ability of a microbial consortium dominated by filamentous cyanobacteria to induce the precipitation of carbonate minerals. Phototrophic microbes, such as cyanobacteria, have been proposed as a means for producing biodiesel and other value added products because of their efficiency as solar collectors and low requirement for valuable, cultivable land in comparison to crops (Dismukes et al., 2008). Carbonate precipitation and biomass production could be facilitated using specifically designed ponds to collect waters rich in dissolved cations (e.g., Mg2+ and Ca2+), which would allow for evapoconcentration and provide an appropriate environment for growth of cyanobacteria. Microbially mediated carbonate precipitation does not require large quantities of energy or chemicals needed for industrial systems that have been proposed for rapid carbon capture and storage via mineral carbonation (e.g., Lackner et al., 1995). Therefore, this biogeochemical approach may represent a readily

  16. Remote Sensing, Geology and Geochemistry on the GVIII Uranium Mineralization, Gabal Gattar, North Eastern Desert, Egypt

    International Nuclear Information System (INIS)

    Elkholy, D.M.; Elhusseiny, M.O.; Saleh, W.H.; Elzalaky, M.A.

    2012-01-01

    mineralization was recorded closely to the altered hematitized zones. Environmental Scanning Electron Microscope (ESEM) and XRD techniques recorded secondary uranium minerals as uranophane and U-bearing accessory minerals as columbite, betafite, zircon and violet fluorite.

  17. SkyMine Carbon Mineralization Pilot Project

    Energy Technology Data Exchange (ETDEWEB)

    Christenson, Norm; Walters, Jerel

    2014-12-31

    This Topical Report addresses accomplishments achieved during Phase 2b of the SkyMine® Carbon Mineralization Pilot Project. The primary objectives of this project are to design, construct, and operate a system to capture CO2 from a slipstream of flue gas from a commercial coal-fired cement kiln, convert that CO2 to products having commercial value (i.e., beneficial use), show the economic viability of the CO2 capture and conversion process, and thereby advance the technology to the point of readiness for commercial scale demonstration and deployment. The overall process is carbon negative, resulting in mineralization of CO2 that would otherwise be released into the atmosphere. The project will also substantiate market opportunities for the technology by sales of chemicals into existing markets, and identify opportunities to improve technology performance and reduce costs at the commercial scale. The project is being conducted in two phases. The primary objectives of Phase 1 were to evaluate proven SkyMine® process chemistry for commercial pilot-scale operation and complete the preliminary design for the pilot plant to be built and operated in Phase 2, complete a NEPA evaluation, and develop a comprehensive carbon life cycle analysis. The objective of Phase 2b was to build the pilot plant to be operated and tested in Phase 2c.

  18. A consistent thermodynamic database for cement minerals

    International Nuclear Information System (INIS)

    Blanc, P.; Claret, F.; Burnol, A.; Marty, N.; Gaboreau, S.; Tournassat, C.; Gaucher, E.C.; Giffault, E.; Bourbon, X.

    2010-01-01

    Document available in extended abstract form only. In the context of waste confinement and, more specifically, waste from the nuclear industry, concrete is used both as a confinement and as a building material. The exposure to high temperatures makes its geochemical behaviour difficult to predict over large periods of time. The present work aims to elucidate the temperature dependency of the thermodynamic functions related to minerals from the concrete or associated with some of its degradation products. To address precisely these functions is a key issue in order to investigate correctly the cement/clay interaction, from a geochemical point of view. A large set of experimental data has been collected, for the chemical systems CaO-SiO 2 -H 2 O, SO 3 -Al 2 O 3 - CaO-CO 2 -Cl-H 2 O and SiO 2 -Al 2 O 3 -CaO-H 2 O, including iron and magnesium bearing phases. Data include calorimetric measurements when available and results from equilibration experiments. The stability of C-S-H phases was considered as a specific issue, those phases may appear both as amorphous or crystalline minerals. In addition, the composition of amorphous minerals is still under debate. The phase diagram of crystalline phases was refined, providing the thermodynamic function of most of the main minerals. Then, we were able to build up a polyhedral model from the refined properties. The composition and the equilibrium constants of amorphous C-S-H, at room temperature, were derived from a large a set of equilibration data. Finally, the thermodynamic functions were completed by using the polyhedral model, both for amorphous and crystalline phases, in some cases. A verification test, based on reaction enthalpies derived from experimental data, indicates that predicted values for amorphous C-S-H are in close agreement with experimental data. For phases other than C-S-H, we have proceeded for each mineral the following way: - the equilibrium constant at 25 deg. C is selected from a single experimental

  19. Minerals in deserts

    International Nuclear Information System (INIS)

    Smith, G.I.

    1982-01-01

    Almost any kind of mineral deposit can occur in desert areas, and the lack of vegetation and soil cover makes finding them easier. Some kinds of deposits, though, are more likely to occur in deserts than elsewhere. Some of these result from processes genetically related to the present desert climate that improved lower grade deposits of ore. One such process, termed secondary enrichment, is most effective in areas with deep water tables, and many low-grade copper, silver, and uranium deposits have been converted into mineable ore by the downward migration and redeposition of soluble metals. In a desert terrane, placer processes are effective whenever running water flowing over steep slopes erodes outcropping ore bodies and transports and concentrates the heavier ore minerals at lower levels, thus converting low-grade or hard-to-mine bedrock deposits into economically workable concentrations. Other kinds of deposits are better preserved in deserts because the lower rainfall at the surface, and the lower volume of flow and the greater depths to groundwater, result in less destruction of soluble ores; deposits of salines and phosphates are the most notable ores affected by these factors. Still other ore deposits are created as a consequence of the arid climate, mostly because the high evaporation rates operating on standing bodies of water produce brines that can lead directly to concentrations of salts and indirectly to secondary minerals, such as zeolites, that are produced by reaction of silicate minerals with saline waters

  20. Carbonizing bituminous minerals

    Energy Technology Data Exchange (ETDEWEB)

    1921-05-01

    A process for carbonizing bituminous minerals, like oil-shale, in a furnace with addition of air in the presence of heat-receiving material is characterized by the fact that to the feed such solid or liquid material (with the exception of oil) is added, which, through vaporization or heat-binding decomposition or conversion, hinders the establishment of excessive temperatures.

  1. Uruguay minerals fuels

    International Nuclear Information System (INIS)

    Goso, H.

    1967-01-01

    In this report the bases for the development of the necessary works of prospection are exposed on mineral fuels of Uruguay. We have taken the set from: coal, lutitas bituminous, uranium, petroleum and disturbs. In all the cases we have talked about to the present state of the knowledge and to the works that we considered necessary to develop in each case

  2. Clinker mineral hydration at reduced relative humidities

    DEFF Research Database (Denmark)

    Jensen, Ole Mejlhede

    1998-01-01

    This report deals with gas phase hydration of pure cement clinker minerals at reduced relative humidities. This is an important subject in relation to modern high performance concrete which may self-desiccate during hydration. In addition the subject has relevance to storage stability where...... prehydration may occur. In the report both theoretical considerations and experimental data are presented. It is suggested that the initiation of hydration during water vapour exposure is nucleation controlled....

  3. Geology and geochemistry of Massangana Granitoid Complex, Brazil, and its relation with tin mineralization

    International Nuclear Information System (INIS)

    Romanini, S.J.

    1982-01-01

    The geochemical and petroLogical characteristics of the Massangana Granitoid Complex, situated in the Rondonia Federal Territory, Brazil, aiming to discriminate the tin mineralized granitic rocks from the no mineralized ones. The collected samples consists of examples in tin mineralized and sterile phases. The elements traces were determined by x-ray fluorescence analysis, emission spectrography, molecular absorption spectrophotometry and atomic absorption spectrophotometry. The complex edifying evolved in four sucessive episodes called Massangana Phase, Bom Jardim Phase, Sao domingos Phase and Taboca Phase ordered stratigraphycally in this sequence. (author/M.C.K.) [pt

  4. Aggregate and Mineral Resources - Industrial Mineral Mining Operations

    Data.gov (United States)

    NSGIC Education | GIS Inventory — An Industrial Mineral Mining Operation is a DEP primary facility type related to the Industrial Mineral Mining Program. The sub-facility types are listed below:Deep...

  5. Effect of soil metal contamination on glyphosate mineralization: role of zinc in the mineralization rates of two copper-spiked mineral soils.

    Science.gov (United States)

    Kim, Bojeong; Kim, Young Sik; Kim, Bo Min; Hay, Anthony G; McBride, Murray B

    2011-03-01

    A systematic investigation into lowered degradation rates of glyphosate in metal-contaminated soils was performed by measuring mineralization of [(14)C]glyphosate to (14)CO(2) in two mineral soils that had been spiked with Cu and/or Zn at various loadings. Cumulative (14)CO(2) release was estimated to be approximately 6% or less of the amount of [(14)C]glyphosate originally added in both soils over an 80-d incubation. For all but the highest Cu treatments (400 mg kg(-1)) in the coarse-textured Arkport soil, mineralization began without a lag phase and declined over time. No inhibition of mineralization was observed for Zn up to 400 mg kg(-1) in either soil, suggesting differential sensitivity of glyphosate mineralization to the types of metal and soil. Interestingly, Zn appeared to alleviate high-Cu inhibition of mineralization in the Arkport soil. The protective role of Zn against Cu toxicity was also observed in the pure culture study with Pseudomonas aeruginosa, suggesting that increased mineralization rates in high Cu soil with Zn additions might have been due to alleviation of cellular toxicity by Zn rather than a mineralization specific mechanism. Extensive use of glyphosate combined with its reduced degradation in Cu-contaminated, coarse-textured soils may increase glyphosate persistence in soil and consequently facilitate Cu and glyphosate mobilization in the soil environment. Copyright © 2010 SETAC.

  6. A study on mineralization U,REE and related processes in anomaly No.6 Khoshomy area central Iran

    International Nuclear Information System (INIS)

    Heidaryan, F.

    2005-01-01

    Uranium mineralization in Khoshomy prospect, located in central. part of Iran, with 303-15000 (cps) and 14 to 4000 (ppm) released, The main rock types include: gneiss, granite, pegmatite and migmatite, that influenced by pegmatite-albitic vines (quartz-heldespatic). Acidic and basic dykes, granodioritic, units and dolomite and marble have been seen. The alteration associated with the mineralization is potassic, argillic, propylitic, carbonization, silisificaition and hematitizaition. Uranium mineralization occurred in a hydrothermal phase with Cu, Mo, Ni and Au elements. Uranium primary minerals include pitchblende, coffinite, uraninite; and uranium secondary minerals include uranophane and . boltwoodite. REE mineralization occurred by the potassic phase in peginatitization process

  7. Oxygen Extraction from Minerals

    Science.gov (United States)

    Muscatello, Tony

    2017-01-01

    Oxygen, whether used as part of rocket bipropellant or for astronaut life support, is a key consumable for space exploration and commercialization. In Situ Resource Utilization (ISRU) has been proposed many times as a method for making space exploration more cost effective and sustainable. On planetary and asteroid surfaces the presence of minerals in the regolith that contain oxygen is very common, making them a potential oxygen resource. The majority of research and development for oxygen extraction from minerals has been for lunar regolith although this work would generally be applicable to regolith at other locations in space. This presentation will briefly survey the major methods investigated for oxygen extraction from regolith with a focus on the current status of those methods and possible future development pathways. The major oxygen production methods are (1) extraction from lunar ilmenite (FeTiO3) with either hydrogen or carbon monoxide, (2) carbothermal reduction of iron oxides and silicates with methane, and (3) molten regolith electrolysis (MRE) of silicates. Methods (1) and (2) have also been investigated in a two-step process using CO reduction and carbon deposition followed by carbothermal reduction. All three processes have byproducts that could also be used as resources. Hydrogen or carbon monoxide reduction produce iron metal in small amounts that could potentially be used as construction material. Carbothermal reduction also makes iron metal along with silicon metal and a glass with possible applications. MRE produces iron, silicon, aluminum, titanium, and glass, with higher silicon yields than carbothermal reduction. On Mars and possibly on some moons and asteroids, water is present in the form of mineral hydrates, hydroxyl (-OH) groups on minerals, andor water adsorbed on mineral surfaces. Heating of the minerals can liberate the water which can be electrolyzed to provide a source of oxygen as well. The chemistry of these processes, some key

  8. Indústria mineral

    Directory of Open Access Journals (Sweden)

    Iran F. Machado

    1998-08-01

    Full Text Available A INDÚSTRIA mineral brasileira é analisada, de modo sucinto, face aos desafios impostos pela globalização contemporânea. As mudanças profundas ocorridas no contexto internacional na última década, abrangendo as esferas política, econômica, social e institucional, exigem uma reflexão aprofundada sobre o papel a ser desempenhado pelo Brasil no comércio internacional de bens minerais. De um lado, as oportunidades de aproveitamento de jazidas de classe internacional, principalmente na Amazônia, são bastante promissoras. Por outro, não se deve ignorar que: a explotação dessas reservas terá de obedecer a critérios de sustentabilidade, seguindo paradigmas já adotados em países desenvolvidos; o Brasil terá de garantir a sua competitividade diante dos seus principais concorrentes (Austrália, CEI, China e Índia. A questão dos minerais estratégicos é também abordada, com ênfase nas preocupações demonstradas pelo Departamento de Estado dos EUA. Finalmente, são alinhados três cenários possíveis para o desempenho futuro da mineração brasileira, instando-se o governo a dedicar maior atenção ao destino do nosso subsolo.THE MINERAL industry of Brazil is briefly analysed vis-à-vis the challenges imposed by the cruenta globalization process. The profound changes that occurred in the international framework during the last decade, encompassing the political, economic, social, and institutional structures, demand a thorough appraisal about the role to be played by Brazil in the international market of mineral commodities. On one hand, the opportunities open for world class deposits, mainly in the Amazon, are very promising. On the other hand, it is mandatory to take into account that: the exploitation of these reserves shall comply with sound sustainability criteria, following guidelines already adopted by some developed countries; Brazil will have to demonstrate its competitiveness among the major competitors (Australia

  9. The nanosphere iron mineral(s) in Mars soil

    Science.gov (United States)

    Banin, A.; Ben-Shlomo, T.; Margulies, L.; Blake, D. F.; Mancinelli, R. L.; Gehring, A. U.

    1993-01-01

    A series of surface-modified clays containing nanophase (np) iron/oxyhydroxides of extremely small particle sizes, with total iron contents as high as found in Mars soil, were prepared by iron deposition on the clay surface from ferrous chloride solution. Comprehensive studies of the iron mineralogy in these 'Mars-soil analogs' were conducted using chemical extractions, solubility analyses, pH and redox, x ray and electron diffractometry, electron microscopic imaging specific surface area and particle size determinations, differential thermal analyses, magnetic properties characterization, spectral reflectance, and Viking biology simulation experiments. The clay matrix and the procedure used for synthesis produced nanophase iron oxides containing a certain proportion of divalent iron, which slowly converts to more stable, fully oxidized iron minerals. The noncrystalline nature of the iron compounds precipitated on the surface of the clay was verified by their complete extractability in oxalate. Lepidocrocite (gamma-FeOOH) was detected by selected area electron diffraction. It is formed from a double iron Fe(II)/Fe(III) hydroxyl mineral such as 'green rust', or ferrosic hydroxide. Magnetic measurements suggested that lepidocrocite converted to the more stable meaghemite (gamma-Fe203) by mild heat treatment and then to nanophase hematite (aplha-Fe203) by extensive heat treatment. Their chemical reactivity offers a plausible mechanism for the somewhat puzzling observations of the Viking biology experiments. Their unique chemical reactivities are attributed to the combined catalytic effects of the iron oxide/oxyhydroxide and silicate phase surfaces. The mode of formation of these (nanophase) iron oxides on Mars is still unknown.

  10. Outlook 96: Minerals and Energy

    International Nuclear Information System (INIS)

    1996-01-01

    Papers discussing the future of Australia's minerals and energy are presented under the following headings: Australia in the global minerals and energy markets; minerals exploration; steelmaking raw materials; aluminium and alumina; gold; nickel; base metals; titanium minerals; energy for a sustainable future; electricity; electricity in Asia; crude oil; coal trade; natural gas in Australia and uranium. Relevant papers are individually indexed/abstracted. Tabs., figs., refs

  11. International availability of energy minerals

    Energy Technology Data Exchange (ETDEWEB)

    White, N A [Norman White Associates, London (UK)

    1979-06-01

    Whereas the ultimate world supply of energy minerals - defined as fossil fuels and fissile minerals - is controlled by geological factors, the actual supply at any particular time is controlled by economic feasibility, technological innovations and/or political decisions. This paper identifies and discusses the principal uncertainties surrounding the international availability of energy minerals from now until the end of the century. A brief comparison is also made between energy and non-energy minerals.

  12. Reactor design considerations in mineral sequestration of carbon dioxide

    International Nuclear Information System (INIS)

    Ityokumbul, M.T.; Chander, S.; O'Connor, William K.; Dahlin, David C.; Gerdemann, Stephen J.

    2001-01-01

    One of the promising approaches to lowering the anthropogenic carbon dioxide levels in the atmosphere is mineral sequestration. In this approach, the carbon dioxide reacts with alkaline earth containing silicate minerals forming magnesium and/or calcium carbonates. Mineral carbonation is a multiphase reaction process involving gas, liquid and solid phases. The effective design and scale-up of the slurry reactor for mineral carbonation will require careful delineation of the rate determining step and how it changes with the scale of the reactor. The shrinking core model was used to describe the mineral carbonation reaction. Analysis of laboratory data indicates that the transformations of olivine and serpentine are controlled by chemical reaction and diffusion through an ash layer respectively. Rate parameters for olivine and serpentine carbonation are estimated from the laboratory data

  13. Imaging and Analytical Approaches for Characterization of Soil Mineral Weathering

    Energy Technology Data Exchange (ETDEWEB)

    Dohnalkova, Alice; Arey, Bruce; Varga, Tamas; Miller, Micah; Kovarik, Libor

    2017-07-01

    Soil minerals weathering is the primary natural source of nutrients necessary to sustain productivity in terrestrial ecosystems. Soil microbial communities increase soil mineral weathering and mineral-derived nutrient availability through physical and chemical processes. Rhizosphere, the zone immediately surrounding plant roots, is a biogeochemical hotspot with microbial activity, soil organic matter production, mineral weathering, and secondary phase formation all happening in a small temporally ephemeral zone of steep geochemical gradients. The detailed exploration of the micro-scale rhizosphere is essential to our better understanding of large-scale processes in soils, such as nutrient cycling, transport and fate of soil components, microbial-mineral interactions, soil erosion, soil organic matter turnover and its molecular-level characterization, and predictive modeling.

  14. LISp-Miner Control Language description of scripting language implementation

    Directory of Open Access Journals (Sweden)

    Milan Simunek

    2014-04-01

    Full Text Available This paper introduces the LISp-Miner Control Language – a scripting language for the LISp-Miner system, an academic system for knowledge discovery in databases. The main purpose of this language is to provide programmable means to all the features of the LISp-Miner system and mainly to automate the main phases of data mining – from data introduction and preprocessing, formulation of analytical tasks, to discovery of the most interesting patterns. In this sense, the language is a necessary prerequisite for the EverMiner project of data mining automation. Language will serve other purposes too – for an automated verification of the LISp-Miner system functionality before a new version is released and as an educational tool in advanced data mining courses.

  15. Aggregates from mineral wastes

    Directory of Open Access Journals (Sweden)

    Baic Ireneusz

    2016-01-01

    Full Text Available The problem concerning the growing demand for natural aggregates and the need to limit costs, including transportation from remote deposits, cause the increase in growth of interest in aggregates from mineral wastes as well as in technologies of their production and recovery. The paper presents the issue related to the group of aggregates other than natural. A common name is proposed for such material: “alternative aggregates”. The name seems to be fully justified due to adequacy of this term because of this raw materials origin and role, in comparison to the meaning of natural aggregates based on gravel and sand as well as crushed stones. The paper presents characteristics of the market and basic application of aggregates produced from mineral wastes, generated in the mining, power and metallurgical industries as well as material from demolished objects.

  16. The bismuth miners study

    International Nuclear Information System (INIS)

    Grosche, B.; Kreuzer, M.; Kreisheimer, M.; Schnelzer, M.; Tschense, A.; Gottschalk, K.

    2005-01-01

    The Federal Radiation Protection Office carried out a retrospective cohort study on some 60,000 former employees of the SAG/SDAG Wismut. The purpose of the study was to validate the radon-related risk of acquiring lung cancer previously calculated from 11 jointly evaluated studies among miners on the basis of an independent, homogeneous data record of comparable size. A further goal was to study the risk of acquiring extrapulmonal tumours. This paper only briefly describes the sampling, design and methods used in the study, as these were already presented during the Radon Status Talks. The first follow-up on the cohort was completed in 2003. Around this time a job exposure matrix (JEM) suitable for scientific inquiries was made available by the professional miners' association and the roof organisation of professional trade associations (HVBG). This paper is the first to report on the outcome of the risk analysis in direct comparison with the results found by BEIR

  17. Iodine mineral waters

    Directory of Open Access Journals (Sweden)

    Iluta Alexandru

    2011-11-01

    Full Text Available Iodine mineral waters are found especially in sub-Carpathian region, also in regions with Salif deposits. Waters are currently used iodine in drinking cure for chaps and Basedow. Are also indicated in balneology. Iodine water containing at least 1 mg L, there is pure iodine is usually given the nature of other types of mineral waters further: sodium chlorinated water (Bazna (50-70 mg iodine / l, Baile Govora (50 - 70 mg / l, Bălţăteşti (4-5 mg / l, salted Monteoru (30 mg / l, mine water mixed alkaline chlorination, sulphate, which are indicated for crenoterapie (hypo or isotonic to the bathrooms Olăneşti or Călimăneşti-Căciulata.

  18. Rock and mineral magnetism

    CERN Document Server

    O’Reilly, W

    1984-01-01

    The past two decades have witnessed a revolution in the earth sciences. The quantitative, instrument-based measurements and physical models of. geophysics, together with advances in technology, have radically transformed the way in which the Earth, and especially its crust, is described. The study of the magnetism of the rocks of the Earth's crust has played a major part in this transformation. Rocks, or more specifically their constituent magnetic minerals, can be regarded as a measuring instrument provided by nature, which can be employed in the service of the earth sciences. Thus magnetic minerals are a recording magnetometer; a goniometer or protractor, recording the directions of flows, fields and forces; a clock; a recording thermometer; a position recorder; astrain gauge; an instrument for geo­ logical surveying; a tracer in climatology and hydrology; a tool in petrology. No instrument is linear, or free from noise and systematic errors, and the performance of nature's instrument must be assessed and ...

  19. Characterization lithium mineralized pegmatite

    International Nuclear Information System (INIS)

    Pereira, E.F.S.; Luz Ferreira, O. da; Cancado, R.Z.L.

    1986-01-01

    Lithium economic importance has increased in the last years. In Brazil its reserves, generally pegmatites bodies, are found in Itinga-Aracuai-MG. This study of characterization belongs to a global plan of lithium mineralized bodies research of 'Arqueana de Minerios e Metais Ltda', which purpose is to give subsidies for implementation of pegmatite unit, in order to make better use of them. (F.E.) [pt

  20. 76 FR 6110 - Conflict Minerals

    Science.gov (United States)

    2011-02-03

    ...-10] RIN 3235-AK84 Conflict Minerals AGENCY: Securities and Exchange Commission. ACTION: Proposed rule...'') and would require any such issuer for which conflict minerals are necessary to the functionality or... body of its annual report whether its conflict minerals originated in the Democratic Republic of the...

  1. Flotation of sulphide minerals 1990

    Energy Technology Data Exchange (ETDEWEB)

    Forssberg, K S.E. [ed.; Luleaa University of Technology, Luleaa (Sweden). Division of Mineral Processing

    1991-01-01

    A total of 27 papers presented at the workshop on flotation of sulphide minerals, reprinted from the International Journal of Mineral Processing, vol. 33, nos. 1-4, are included in this book. They cover various aspects of flotation of such minerals as chalcopyrite, pyrrhotite, galena, malachite and pyrite.

  2. The nanophase iron mineral(s) in Mars soil

    Science.gov (United States)

    Banin, A.; Ben-Shlomo, T.; Margulies, L.; Blake, D. F.; Mancinelli, R. L.; Gehring, A. U.

    1993-01-01

    A series of surface-modified clays containing nanophase (np) iron oxide/oxyhydroxides of extremely small particle sizes, with total iron contents as high as found in Mars soil, were prepared by iron deposition on the clay surface from ferrous chloride solution. Comprehensive studies of the iron mineralogy in these "Mars-soil analogs" were conducted using chemical extractions, solubility analyses, pH and redox, x ray and electron diffractometry, electron microscopic imaging, specific surface area and particle size determinations, differential thermal analyses, magnetic properties characterization, spectral reflectance, and Viking biology simulation experiments. The clay matrix and the procedure used for synthesis produced nanophase iron oxides containing a certain proportion of divalent iron, which slowly converts to more stable, fully oxidized iron minerals. The clay acted as an effective matrix, both chemically and sterically, preventing the major part of the synthesized iron oxides from ripening, i.e., growing and developing larger crystals. The precipitated iron oxides appear as isodiametric or slightly elongated particles in the size range 1-10 nm, having large specific surface area. The noncrystalline nature of the iron compounds precipitated on the surface of the clay was verified by their complete extractability in oxalate. Lepidocrocite (gamma-FeOOH) was detected by selected area electron diffraction. It is formed from a double iron Fe(II)/Fe(III) hydroxy mineral such as "green rust," or ferrosic hydroxide. Magnetic measurements suggested that lepidocrocite converted to the more stable maghemite (gamma-Fe2O3) by mild heat treatment and then to nanophase hematite (alpha-Fe2O3) by extensive heat treatment. After mild heating, the iron-enriched clay became slightly magnetic, to the extent that it adheres to a hand-held magnet, as was observed with Mars soil. The chemical reactivity of the iron-enriched clays strongly resembles, and offers a plausible mechanism

  3. Mineral potential tracts for shoreline Ti-Zr placer deposits (phase V, deliverable 85): Chapter P in Second projet de renforcement institutionnel du secteur minier de la République Islamique de Mauritanie (PRISM-II)

    Science.gov (United States)

    Beaudoin, Georges

    2015-01-01

    Shoreline placer Ti deposits are composed of ilmenite, rutile, zircon, monazite, and magnetite in well-sorted, fine- to medium-grained sand in coastal dunes, beaches and inlets. In addition to titanium, zirconium, in particular, and rare earth elements (REE) have become a major source of value in shoreline placer deposits. Shoreline placer deposits form mostly on tropical beaches around the world (fig. 1), and consist of dark sand layers rich in heavy minerals that are resistant to mechanical abrasion and chemical weathering. According to Hamilton (1995), shoreline placer deposits supply approximately 80 percent of the world’s rutile production, 25 percent of ilmenite, 100 percent of zircon, and 50 percent of both monazite and xenotime.

  4. Molecular nanomechanics of nascent bone: fibrillar toughening by mineralization

    Science.gov (United States)

    Buehler, Markus J.

    2007-07-01

    Mineralized collagen fibrils are highly conserved nanostructural building blocks of bone. By a combination of molecular dynamics simulation and theoretical analysis it is shown that the characteristic nanostructure of mineralized collagen fibrils is vital for its high strength and its ability to sustain large deformation, as is relevant to the physiological role of bone, creating a strong and tough material. An analysis of the molecular mechanisms of protein and mineral phases under large deformation of mineralized collagen fibrils reveals a fibrillar toughening mechanism that leads to a manifold increase of energy dissipation compared to fibrils without mineral phase. This fibrillar toughening mechanism increases the resistance to fracture by forming large local yield regions around crack-like defects, a mechanism that protects the integrity of the entire structure by allowing for localized failure. As a consequence, mineralized collagen fibrils are able to tolerate microcracks of the order of several hundred micrometres in size without causing any macroscopic failure of the tissue, which may be essential to enable bone remodelling. The analysis proves that adding nanoscopic small platelets to collagen fibrils increases their Young's modulus and yield strength as well as their fracture strength. We find that mineralized collagen fibrils have a Young's modulus of 6.23 GPa (versus 4.59 GPa for the collagen fibril), yield at a tensile strain of 6.7% (versus 5% for the collagen fibril) and feature a fracture stress of 0.6 GPa (versus 0.3 GPa for the collagen fibril).

  5. Molecular nanomechanics of nascent bone: fibrillar toughening by mineralization

    International Nuclear Information System (INIS)

    Buehler, Markus J

    2007-01-01

    Mineralized collagen fibrils are highly conserved nanostructural building blocks of bone. By a combination of molecular dynamics simulation and theoretical analysis it is shown that the characteristic nanostructure of mineralized collagen fibrils is vital for its high strength and its ability to sustain large deformation, as is relevant to the physiological role of bone, creating a strong and tough material. An analysis of the molecular mechanisms of protein and mineral phases under large deformation of mineralized collagen fibrils reveals a fibrillar toughening mechanism that leads to a manifold increase of energy dissipation compared to fibrils without mineral phase. This fibrillar toughening mechanism increases the resistance to fracture by forming large local yield regions around crack-like defects, a mechanism that protects the integrity of the entire structure by allowing for localized failure. As a consequence, mineralized collagen fibrils are able to tolerate microcracks of the order of several hundred micrometres in size without causing any macroscopic failure of the tissue, which may be essential to enable bone remodelling. The analysis proves that adding nanoscopic small platelets to collagen fibrils increases their Young's modulus and yield strength as well as their fracture strength. We find that mineralized collagen fibrils have a Young's modulus of 6.23 GPa (versus 4.59 GPa for the collagen fibril), yield at a tensile strain of 6.7% (versus 5% for the collagen fibril) and feature a fracture stress of 0.6 GPa (versus 0.3 GPa for the collagen fibril)

  6. Iron oxyhydroxide mineralization on microbial extracellular polysaccharides

    Energy Technology Data Exchange (ETDEWEB)

    Chan, Clara S.; Fakra, Sirine C.; Edwards, David C.; Emerson, David; Banfield, Jillian F.

    2010-06-22

    Iron biominerals can form in neutral pH microaerophilic environments where microbes both catalyze iron oxidation and create polymers that localize mineral precipitation. In order to classify the microbial polymers that influence FeOOH mineralogy, we studied the organic and mineral components of biominerals using scanning transmission X-ray microscopy (STXM), micro X-ray fluorescence ({mu}XRF) microscopy, and high-resolution transmission electron microscopy (HRTEM). We focused on iron microbial mat samples from a creek and abandoned mine; these samples are dominated by iron oxyhydroxide-coated structures with sheath, stalk, and filament morphologies. In addition, we characterized the mineralized products of an iron-oxidizing, stalk-forming bacterial culture isolated from the mine. In both natural and cultured samples, microbial polymers were found to be acidic polysaccharides with carboxyl functional groups, strongly spatially correlated with iron oxyhydroxide distribution patterns. Organic fibrils collect FeOOH and control its recrystallization, in some cases resulting in oriented crystals with high aspect ratios. The impact of polymers is particularly pronounced as the materials age. Synthesis experiments designed to mimic the biomineralization processes show that the polysaccharide carboxyl groups bind dissolved iron strongly but release it as mineralization proceeds. Our results suggest that carboxyl groups of acidic polysaccharides are produced by different microorganisms to create a wide range of iron oxyhydroxide biomineral structures. The intimate and potentially long-term association controls the crystal growth, phase, and reactivity of iron oxyhydroxide nanoparticles in natural systems.

  7. Characterization of Mexican zeolite minerals

    International Nuclear Information System (INIS)

    Jimenez C, M.J.

    2005-01-01

    50% of the Mexican territory is formed by volcanic sequences of the Pliocene type, which appear extensively in the northwest states (Sonora, Sinaloa, Chihuahua, Durango) and west of Mexico (Jalisco and Nayarit), in central Mexico (Zacatecas, Guanajuato, San Luis Potosi, Queretaro, Hidalgo) and south of Mexico (Guerrero, Oaxaca); therefore, it is to be expected that in our country big locations of natural zeolites exist in its majority of the clinoptilolite type. The present study was focused toward the characterization of two Mexican natural zeolite rocks presumably of the clinoptilolite and filipsite types, one of them comes from the state of Chihuahua and the other of a trader company of non metallic minerals, due that these materials are not characterized, its are not known their properties completely and therefore, the uses that can be given to these materials. In this investigation work it was carried out the characterization of two Mexican zeolite rocks, one coming from the Arroyo zone, municipality of La Haciendita, in the state of Chihuahua; and the other one was bought to a trader company of non metallic minerals. The two zeolites so much in their natural form as conditioned with sodium; they were characterized by means of X-ray diffraction, scanning electron microscopy of high vacuum and elementary microanalysis (EDS), surface area analysis (BET), thermal gravimetric analysis. To differentiate the heulandite crystalline phase of the other clinoptilolite rock, its were carried out thermal treatments. The quantification of Al, Na, Ca, K, Mg, Fe was carried out in solution, by means of atomic absorption spectroscopy and the quantity of Si was determined by gravimetry. The zeolite rocks presented for the major part the crystalline heulandite and clinoptilolite phases for the most part, and it was found that the zeolite coming from the state of Chihuahua possesses a bigger content of heulandite and the denominated filipsite it is really a zeolite

  8. Nuclear minerals in Pakistan

    International Nuclear Information System (INIS)

    Mansoor, M.

    2005-01-01

    Strategic importance of Nuclear Minerals was recognized during early formative years of the Pakistan Atomic Energy Commission, and prospecting for uranium was started in Dera Ghazi Khan in collaboration with the Geological Survey of Pakistan (GSP) as early as 1961. Later, the responsibility for countrywide surveys and exploration was fully entrusted with PAEC and in this respect a Directorate of Nuclear Minerals(DNM) was established in 1966 at Lahore. Later, DNM was shifted to the Atomic Energy Centre (AEC), Lahore building and renamed as Atomic Energy Minerals Centre. It has state-of-the-art Chemistry, Mineralogy, Remote Sensing and Electronics Laboratories and an Ore Processing Pilot Plant. The Centre has Prospecting, Exploration, Geophysics, Geochemistry, Geo-tectonics, Mining and Drilling Sections. Regional Offices have been established to facilitate work at Karachi, Quetta and Peshawar. Siwaliks were recognized as a favorable geological formation of prime importance. Sandstone-shale sequence of Siwaliks Formation is exposed in all provinces of Pakistan and in Azad Jammu and Kashmir (AJK), broadly categorized into Rajanpur-Dera Ghazi Khan, Bannu Basin-Kohat Plateau and Potwar-AJK zones. Baghalchur, Nangar Nai and Taunsa uranium deposits have been discovered in the Rajanpur- D.G. Khan Zone. Qabul Khel and Shanawah Uranium deposits have been discovered in the Shanawah-Kohat Plateau Zone. Prospection and exploration is in progress. The first uranium mine was opened at Baghalchur, and uranium mill was established at D.G Khan in 1977-78 all by indigenous effort. The uranium mine was the most advanced and mechanized mine of that time in the country. Later, a second uranium mine was opened at Qabul Khel in 1992, which was based on a new and advanced in situ leach technology, developed to suit local geological and ore zone parameters. Mining of Nanganai and Taunsa Deposits was started respectively in 1996 and 2002, and is also based on in situ leach technology which is

  9. Minerals and rumen function

    International Nuclear Information System (INIS)

    Smith, R.H.

    1984-01-01

    The mechanisms are discussed of some clinical disorders, characteristic only of ruminants and related to the effects of abnormal mineral intake on rumen function. With particular attention to tropical conditions, consideration is given to: (a) the possible effects of phosphorus deficiency on rumen microbial activity; (b) the depression of rumen microbial synthesis in sulphur deficiency; (c) the inhibition of magnesium absorption from the forestomachs; and (d) the involvement of the rumen microorganisms in leading to copper and vitamin B 12 deficiencies as a result of low intakes of cobalt. (author)

  10. Reducing coal miner absenteeism

    Energy Technology Data Exchange (ETDEWEB)

    Peters, R.H.; Clingan, M.R. (Bureau of Mines, PA (USA). Pittsburgh Research Center)

    1989-09-01

    High absenteeism at coal mines can seriously affect safety and hamper productivity. Several effective strategies for achieving high attendance which mine operators may not have considered are presented and a method is proposed for implementing programs for minimizing absenteeism among coal miners. The best strategies for improving attendance will vary according to the needs and circumstances of the particular mine, however, the process for establishing such a program is relatively invariant. A four-stage process is recommended; evaluate data from prior attendance records, communicate attendance goals and policy, develop and implement an attendance promotion program, and recycle. 12 refs., 5 figs.

  11. Refining mineral oils

    Energy Technology Data Exchange (ETDEWEB)

    1946-07-05

    A process is described refining raw oils such as mineral oils, shale oils, tar, their fractions and derivatives, by extraction with a selected solvent or a mixture of solvents containing water, forming a solvent more favorable for the hydrocarbons poor in hydrogen than for hydrocarbons rich in hydrogen, this process is characterized by the addition of an aiding solvent for the water which can be mixed or dissolved in the water and the solvent or in the dissolving mixture and increasing in this way the solubility of the water in the solvent or the dissolving mixture.

  12. RELATIVE TRACE MINERAL BIOAVAILABILITY

    OpenAIRE

    Rchard D. Miles; Peter R. Henry

    2006-01-01

    Para determinar a eficiência de utilização de elementos minerais dietéticos, deve-se conhecer a biodisponibilidade relativa de cada elemento de um determinado ingrediente ou de uma ração completa. Análises químicas da dieta ou de um determinado ingrediente não indicam a efetividade biológica de um nutriente. Existem muitos fatores que influenciam a biodisponibilidade dos minerais, especialmente dos minerais-traço, tais como: nível de consumo do mineral, forma química, digestibilidade da dieta...

  13. High temperature phase equilibria and phase diagrams

    CERN Document Server

    Kuo, Chu-Kun; Yan, Dong-Sheng

    2013-01-01

    High temperature phase equilibria studies play an increasingly important role in materials science and engineering. It is especially significant in the research into the properties of the material and the ways in which they can be improved. This is achieved by observing equilibrium and by examining the phase relationships at high temperature. The study of high temperature phase diagrams of nonmetallic systems began in the early 1900s when silica and mineral systems containing silica were focussed upon. Since then technical ceramics emerged and more emphasis has been placed on high temperature

  14. Mineral supplementation for grazing ruminants

    International Nuclear Information System (INIS)

    McDowell, L.R.; Conrad, J.H.; Ellis, G.L.

    1986-01-01

    Grazing ruminants to which concentrate feeds cannot be economically fed must rely on self-feeding of mineral supplements. A number of factors affect mineral consumption of free-choice mixtures. Livestock exhibit little nutritional wisdom and will select palatable mixtures in preference to mixtures designed to meet their requirements. Palatability and appetite stimulators are often used to achieve a more uniform herd-wide consumption. It is best to formulate free-choice mixtures on the basis of analyses or other available data. However, when no information on mineral status is known, a free-choice complete mineral supplement is warranted. A 'complete' mineral mixture usually includes salt, a low fluoride P source, Ca, Co, Cu, I, Mn and Zn. Selenium, Mg, K, S, Fe or additional elements can be incorporated into a mineral supplement as new information suggests a need. The detriment to ruminant production caused by providing Ca, Se and Cu in excess can be greater than any benefit derived by providing a mineral supplement. In regions where high forage Mo predominates, three to five times the Cu content in mineral mixtures is needed to counteract Mo toxicity. Supplemental minerals are most critical during the wet season, when cattle are gaining weight rapidly and energy and protein supplies are adequate. Economic return on mineral supplementation is high. (author)

  15. The peraluminous leucogranitic complex of St Sylvestre (France, Massif Central NW). Evolution of the crystallochemistry of mineral phases and of the geochemistry of major and trace elements. Polygenetism characterization in peraluminous granites. Implication on uranium metallogeny

    International Nuclear Information System (INIS)

    Friedrich, M.

    1983-07-01

    The main purpose of this study is to improve the knowledge of the behaviour of uranium during magmatic and late magmatic processes. In France and other part of the world the close association of uranium (Sn-W) deposits and showings with this type of granite justifies the metallogenic interest of this study. At the scale of the whole granitic complex two distinct petrological groups are redefined: the facies of Brame and St Sylvestre. Mineral paragenesis closely follow the geochemical differentiation. Abundance of uraninite and scarcity of monazite and zircon, are additional features of these samples. The opposite behaviour of monazite (typical of the less evolved facies) and uraninite (whose abundance is directly related to the degree of differentiation) suggests two conclusions. Abundance in uranium is directly related to the magmatic differentiation processes. The early crystallization of monazite and zircon and their high abundance in poorly evolved facies imply a compatible behaviour for Th, Zr and light rare earths. More detailed geochemical studies evidence heterogeneities at on hectometric and locally at a metric scale. Differentiation processes, which appear to be continuous at a kilometric scale in the St Sylvestre facies, are discontinuous at the hectometric and metric scale. Such petrogeochemical discontinuities, implying petrogenitic heterogeneities are expressed in the concept of polygenetism [fr

  16. Aggregate and Mineral Resources - MO 2014 Industrial Mineral Mines (SHP)

    Data.gov (United States)

    NSGIC State | GIS Inventory — This data set contains names, locations and additional data for active Industrial Mineral Mines permitted with the Missouri Department of Natural Resources, Division...

  17. Formation of secondary minerals in a lysimeter approach - A mineral-microbe interaction

    Science.gov (United States)

    Schäffner, F.; Merten, D.; De Giudici, G.; Beyer, A.; Akob, D. M.; Ricci, P. C.; Küsel, K.; Büchel, G.

    2012-04-01

    Heavy metal contamination of large areas due to uranium mining operations poses a serious long-term environmental problem. In the Ronneburg district (eastern Thuringia, Germany), leaching of low grade uranium bearing ores (uranium content metals, especially Cd, Ni, Co, Cu and Zn due to a residual contamination even after remediation efforts. To reveal the processes of secondary mineral precipitation in the field a laboratory lysimeter approach was set up under in situ-like conditions. Homogenized soil from the field site and pure quartz sand were used as substrates. In general, in situ measurements of redox potentials in the substrates showed highly oxidizing conditions (200-750 mV). Water was supplied to the lysimeter from below via a mariottés bottle containing contaminated groundwater from the field. Evaporation processes were allowed, providing a continuous flow of water. This led to precipitation of epsomite and probably aplowite on the top layer of substrate, similar to what is observed in field investigations. After 4 weeks, the first iron and manganese bearing secondary minerals became visible. Soil water samples were used to monitor the behaviour of metals within the lysimeter. Saturation indices (SI) for different secondary minerals were calculated with PHREEQC. The SI of goethite showed oversaturation with respect to the soil solution. SEM-EDX analyses and IR spectroscopy confirmed the formation of goethite. Geochemical data revealed that goethite formation was mainly dominated by Eh/pH processes and that heavy metals, e.g. Zn and U, could be enriched in this phase. Although Eh/pH data does not support formation of manganese minerals, Mn(II)-oxidizing bacteria (MOB) could be isolated from field soil samples, supporting the fact that microorganisms may influence this natural attenuation process. Laser ablation ICP-MS data reveal accumulation of manganese in MOB biomass on Mn(II)-containing agar plates. Furthermore, it was possible to show the importance

  18. Spectroscopic characterization of manganese minerals.

    Science.gov (United States)

    Lakshmi Reddy, S; Padma Suvarna, K; Udayabhaska Reddy, G; Endo, Tamio; Frost, R L

    2014-01-03

    Manganese minerals ardenite, alleghanyite and leucopoenicite originated from Madhya Pradesh, India, Nagano prefecture Japan, Sussex Country and Parker Shaft Franklin, Sussex Country, New Jersey respectively are used in the present work. In these minerals manganese is the major constituent and iron if present is in traces only. An EPR study of on all of the above samples confirms the presence of Mn(II) with g around 2.0. Optical absorption spectrum of the mineral alleghanyite indicates that Mn(II) is present in two different octahedral sites and in leucophoenicite Mn(II) is also in octahedral geometry. Ardenite mineral gives only a few Mn(II) bands. NIR results of the minerals ardenite, leucophoenicite and alleghanyite are due to hydroxyl and silicate anions which confirming the formulae of the minerals. Copyright © 2013 Elsevier B.V. All rights reserved.

  19. Response of Microbial Soil Carbon Mineralization Rates to Oxygen Limitations

    Science.gov (United States)

    Keiluweit, M.; Denney, A.; Nico, P. S.; Fendorf, S. E.

    2014-12-01

    The rate of soil organic matter (SOM) mineralization is known to be controlled by climatic factors as well as molecular structure, mineral-organic associations, and physical protection. What remains elusive is to what extent oxygen (O2) limitations impact overall rates of microbial SOM mineralization (oxidation) in soils. Even within upland soils that are aerobic in bulk, factors limiting O2 diffusion such as texture and soil moisture can result in an abundance of anaerobic microsites in the interior of soil aggregates. Variation in ensuing anaerobic respiration pathways can further impact SOM mineralization rates. Using a combination of (first) aggregate model systems and (second) manipulations of intact field samples, we show how limitations on diffusion and carbon bioavailability interact to impose anaerobic conditions and associated respiration constraints on SOM mineralization rates. In model aggregates, we examined how particle size (soil texture) and amount of dissolved organic carbon (bioavailable carbon) affect O2 availability and distribution. Monitoring electron acceptor profiles (O2, NO3-, Mn and Fe) and SOM transformations (dissolved, particulate, mineral-associated pools) across the resulting redox gradients, we then determined the distribution of operative microbial metabolisms and their cumulative impact on SOM mineralization rates. Our results show that anaerobic conditions decrease SOM mineralization rates overall, but those are partially offset by the concurrent increases in SOM bioavailability due to transformations of protective mineral phases. In intact soil aggregates collected from soils varying in texture and SOM content, we mapped the spatial distribution of anaerobic microsites. Optode imaging, microsensor profiling and 3D tomography revealed that soil texture regulates overall O2 availability in aggregate interiors, while particulate SOM in biopores appears to control the fine-scale distribution of anaerobic microsites. Collectively, our

  20. Sub-project 'Simulation in mineral waste of secondary phase formation due to contact with drainage water'. Final report; Teilprojekt 'Simulation der Sekundaermineralbildung in mineralischen Reststoffen in Kontakt mit Sickerwasser'. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Heiser, U.; Kersten, M.

    2003-08-01

    3 mio. metric tons of bottom ash are produced by municipal solid waste incineration annually in Germany, which have to be recycled under tough environmental- and construction-based criteria. Before recycled, the ashes have to be reacted in open-air dumps for at least three months. A field-based survey under the framework of this project was conducted to study the ash ageing. This survey demonstrated that in practice these criteria are only partially reached in the topmost surficial layers of the 3-months ash humps due to hindrance of access by water and CO{sub 2}. According to a hypothesis worked out in earlier projects, the heavy metals remobilized from bottom ash are scavenged by secondary minerals formed during ageing, and kept therefore on a very low concentration niveau in the drainage water. In this project it was tried to simulate this long-term reaction sequence by addition of such sorbents to the short-term S4 leaching test already with fresh bottom ash. The main result is that the low metal concentration niveau was reached already within a few weeks of ash storage because the secondary mineral sorbents are apparently formed quite rapidly in sufficient amounts if both water and CO{sub 2} are allowed to drain the material. It is therefore not necessary to modify the S4 test for assessment according to the criteria ''Quellstaerke nach BBodSchV'', in case ash ageing is performed in an appropriate manner. Nonetheless, laboratory experiments showed that in open ash disposal systems but at enhanced gradient formation, considerable heavy metal fluxes may occur due to high remobilization rates, even at the overall low equilibrium concentrations. (orig.) [German] Bei der Siedlungsabfallverbrennung fallen jaehrlich ca. 3 Mio. Tonnen Rostasche an, die unter Einhaltung umwelt- und bautechnischer Kriterien wiederverwertet werden muessen. Vor der eigentlichen Verwertung ist eine dreimonatige Alterung der Aschen vorgeschrieben. Im Rahmen dieses

  1. Destructive textures around radioactive minerals

    International Nuclear Information System (INIS)

    Montel, J.M.; Seydoux-Guillaume, A.M.

    2009-01-01

    In most of the rocks, natural uranium and thorium are concentrated in some minerals which provide favourable crystallographic sites. These minerals are thus submitted to an intense auto-irradiation which may transform them. Using conventional investigation methods (petrographic or scanning electronic microscopy, electronic micro-probe) and less conventional ones (transmission electronic microscopy), the authors studied the interfaces between radioactive minerals and their host minerals. They comment the possible mechanical and structural aspects of this interaction by irradiation, and the influence of geological events

  2. Trace Mineral Losses in Sweat

    National Research Council Canada - National Science Library

    Chinevere, Troy D; McClung, James P; Cheuvront, Samuel N

    2007-01-01

    Copper, iron and zinc are nutritionally essential trace minerals that confer vital biological roles including the maintenance of cell structure and integrity, regulation of metabolism, immune function...

  3. Probing the rhizosphere to define mineral organic relationships

    Science.gov (United States)

    Schulz, M. S.; Dohnalkova, A.; Stonestrom, D. A.

    2016-12-01

    Soil organic matter (SOM) accumulation and stabilization over time is an important process as soils are a large carbon reservoir in which feedbacks under changing climates are unclear. The association of SOM with poorly crystalline or short-range-ordered secondary minerals has been shown to be important for carbon stabilization. Commonly used soil extraction techniques display correlations of SOM with secondary phases but do not show causation. The fate of root exudates in soils and processes controlling exudate associations with mineral phases are as yet structurally undefined. Sub-micron exploration of in-situ relations provides valuable information on SOM-mineral interactions. Soils of the Santa Cruz (California) marine terrace chronosequence are used to illustrate changes in deep (> 1 m) rhizosphere through time. Cracks and soil ped faces are sites of high root density and organic matter (biofilm or mucilage) deposition. We employ a variety of scanning electron microscopy (SEM) and scanning transmission electron microscopy (STEM) techniques for high resolution imaging and elemental analyses of deep rhizosphere and associated carbon mineral interactions. In these coastal prairie soils microscopy reveals secondary clay minerals associated with and possibly forming from organic-rich mucilage that occurs along the aforementioned rooting networks on fracture surfaces. We hypothesize that the production of secondary clays in the rhizosphere is an important mode of C incorporation into secondary minerals.

  4. Silicoaluminous minerals analysis

    International Nuclear Information System (INIS)

    Puglisi, Celia; Fina, J.P.

    1987-01-01

    A group of silicoaluminous minerals of known composition have been analyzed by means of an energy dispersive electron microprobe. The analysis has been performed using a standarless semiquantitative method. The concentration was calculated using the program included in the software of the on-line computer, based on the ZAF correction. It is well known that it is difficult to analyze Si, Al and Na by this method because the absortion correction in the range of 0.9 to 2.0 KeV is not very accurate and the background substraction is also questionable. The purpose of this work is to evaluate the errors involved in these measurements and the best operation conditions. (Author) [es

  5. Protein- mediated enamel mineralization

    Science.gov (United States)

    Moradian-Oldak, Janet

    2012-01-01

    Enamel is a hard nanocomposite bioceramic with significant resilience that protects the mammalian tooth from external physical and chemical damages. The remarkable mechanical properties of enamel are associated with its hierarchical structural organization and its thorough connection with underlying dentin. This dynamic mineralizing system offers scientists a wealth of information that allows the study of basic principals of organic matrix-mediated biomineralization and can potentially be utilized in the fields of material science and engineering for development and design of biomimetic materials. This chapter will provide a brief overview of enamel hierarchical structure and properties as well as the process and stages of amelogenesis. Particular emphasis is given to current knowledge of extracellular matrix protein and proteinases, and the structural chemistry of the matrix components and their putative functions. The chapter will conclude by discussing the potential of enamel for regrowth. PMID:22652761

  6. Mineral fibres and health

    International Nuclear Information System (INIS)

    Hoskins, J.A.

    2001-01-01

    The use of inorganic fibrous materials is a comparatively new phenomenon and was uncommon before the Industrial Revolution. Humans evolved in a comparatively fibre-free environment and consequently never fully developed the defence mechanisms needed to deal with the consequences of inhaling fibres. However, the urban environment now has an airborne fibre concentration of around 1 f.l -1 , which is a tenfold increase on the natural background. Any sample of ambient air collected indoors or outdoors will probably contain some mineral fibres, but there is little evidence that these pose any risk to human health. They come from asbestos used in brakes, glass and mineral wools used as insulation and fire proofing of buildings, gypsum from plaster and a variety of types from many sources. Few of these have the potential to do any harm. Asbestos is the only fibre of note but urban levels are insignificant compared to occupational exposures. When the health of cohorts occupationally exposed to the several types of asbestos is studied the problem can be put into perspective. Studies of workers in the chrysotile industry exposed to much higher dust levels than in a factory today show no excess lung cancer or mesothelioma. By comparison those living near crocidolite mines, let alone working in them, may develop asbestos-related disease. As always, dose is the critical factor. Chrysotile is cleared from the lungs very efficiently, only the amphiboles are well retained. The only real health problem comes from the earlier use of asbestos products that may now be old, friable and damaged and made from amphibole or mixed fibre. If though, these are still in good condition, they do not pose a health problem. Asbestos-related diseases are very rare in those not occupationally exposed. Where they exist exposure has nearly always been to crocidolite. (author)

  7. SkyMine Carbon Mineralization Pilot Project

    Energy Technology Data Exchange (ETDEWEB)

    Joe Jones; Clive Barton; Mark Clayton; Al Yablonsky; David Legere

    2010-09-30

    This Topical Report addresses accomplishments achieved during Phase 1 of the SkyMine{reg_sign} Carbon Mineralization Pilot Project. The primary objectives of this project are to design, construct, and operate a system to capture CO{sub 2} from a slipstream of flue gas from a commercial coal-fired cement kiln, convert that CO{sub 2} to products having commercial value (i.e., beneficial use), show the economic viability of the CO{sub 2} capture and conversion process, and thereby advance the technology to a point of readiness for commercial scale demonstration and proliferation. The project will also substantiate market opportunities for the technology by sales of chemicals into existing markets, and identify opportunities to improve technology performance and reduce costs at commercial scale. The primary objectives of Phase 1 of the project were to elaborate proven SkyMine{reg_sign} process chemistry to commercial pilot-scale operation and complete the preliminary design ('Reference Plant Design') for the pilot plant to be built and operated in Phase 2. Additionally, during Phase 1, information necessary to inform a DOE determination regarding NEPA requirements for the project was developed, and a comprehensive carbon lifecycle analysis was completed. These items were included in the formal application for funding under Phase 2. All Phase 1 objectives were successfully met on schedule and within budget.

  8. Of minerals and men. [Discovery of new mineral species

    Energy Technology Data Exchange (ETDEWEB)

    De Waal, S.W. (Council for Mineral Technology, Randburg (South Africa))

    1983-01-01

    The rate of discovery of new mineral species appears to be on the increase in Southern Africa and classification and nomenclature, once haphazard, are now subject to international scientific screening and rules. Earlier names entrenched in the literature provide a fascinating background to the minerals scene.

  9. An investigation of the mineral in ductile and brittle cortical mouse bone.

    Science.gov (United States)

    Rodriguez-Florez, Naiara; Garcia-Tunon, Esther; Mukadam, Quresh; Saiz, Eduardo; Oldknow, Karla J; Farquharson, Colin; Millán, José Luis; Boyde, Alan; Shefelbine, Sandra J

    2015-05-01

    Bone is a strong and tough material composed of apatite mineral, organic matter, and water. Changes in composition and organization of these building blocks affect bone's mechanical integrity. Skeletal disorders often affect bone's mineral phase, either by variations in the collagen or directly altering mineralization. The aim of the current study was to explore the differences in the mineral of brittle and ductile cortical bone at the mineral (nm) and tissue (µm) levels using two mouse phenotypes. Osteogenesis imperfecta model, oim(-/-) , mice have a defect in the collagen, which leads to brittle bone; PHOSPHO1 mutants, Phospho1(-/-) , have ductile bone resulting from altered mineralization. Oim(-/-) and Phospho1(-/-) were compared with their respective wild-type controls. Femora were defatted and ground to powder to measure average mineral crystal size using X-ray diffraction (XRD) and to monitor the bulk mineral to matrix ratio via thermogravimetric analysis (TGA). XRD scans were run after TGA for phase identification to assess the fractions of hydroxyapatite and β-tricalcium phosphate. Tibiae were embedded to measure elastic properties with nanoindentation and the extent of mineralization with backscattered electron microscopy (BSE SEM). Results revealed that although both pathology models had extremely different whole-bone mechanics, they both had smaller apatite crystals, lower bulk mineral to matrix ratio, and showed more thermal conversion to β-tricalcium phosphate than their wild types, indicating deviations from stoichiometric hydroxyapatite in the original mineral. In contrast, the degree of mineralization of bone matrix was different for each strain: brittle oim(-/-) were hypermineralized, whereas ductile Phospho1(-/-) were hypomineralized. Despite differences in the mineralization, nanoscale alterations in the mineral were associated with reduced tissue elastic moduli in both pathologies. Results indicated that alterations from normal crystal size

  10. The Thermodynamics of Selenium Minerals in Near-Surface Environments

    Directory of Open Access Journals (Sweden)

    Vladimir Krivovichev

    2017-10-01

    Full Text Available Selenium compounds are relatively rare as minerals; there are presently only 118 known mineral species. This work is intended to codify and systematize the data of mineral systems and the thermodynamics of selenium minerals, which are unstable (selenides or formed in near-surface environments (selenites, where the behavior of selenium is controlled by variations of the redox potential and the acidity of solutions at low temperatures and pressures. These parameters determine the migration of selenium and its precipitation as various solid phases. All selenium minerals are divided into four groups—native selenium, oxide, selenides, and oxysalts—anhydrous selenites (I and hydrous selenites and selenates (II. Within each of the groups, minerals are codified according to the minimum number of independent elements necessary to define the composition of the mineral system. Eh–pH diagrams were calculated and plotted using the Geochemist’s Workbench (GMB 9.0 software package. The Eh–pH diagrams of the Me–Se–H2O systems (where Me = Co, Ni, Fe, Cu, Pb, Zn, Cd, Hg, Ag, Bi, As, Sb, Al and Ca were plotted for the average contents of these elements in acidic waters in the oxidation zones of sulfide deposits. The possibility of the formation of Zn, Cd, Ag and Hg selenites under natural oxidation conditions in near surface environments is discussed.

  11. Clinker mineral hydration at reduced relative humidities

    DEFF Research Database (Denmark)

    Jensen, Ole Mejlhede; Hansen, Per Freiesleben; Lachowski, Eric E.

    1999-01-01

    and experimental data are presented showing that C(3)A can hydrate at lower humidities than either C3S or C2S. It is suggested that the initiation of hydration during exposure to water vapour is nucleation controlled. When C(3)A hydrates at low humidity, the characteristic hydration product is C(3)AH(6......Vapour phase hydration of purl cement clinker minerals at reduced relative humidities is described. This is relevant to modern high performance concrete that may self-desiccate during hydration and is also relevant to the quality of the cement during storage. Both the oretical considerations...

  12. Pulmonary mineralization in four dogs with Cushing's syndrome

    International Nuclear Information System (INIS)

    Berry, C.R.; Ackerman, N.; Monce, K.

    1994-01-01

    The clinical and imaging features of four dogs with Cushing's syndrome and pulmonary mineralization are reviewed. Three dogs presented with a primary complaint of respiratory distress/dyspnea. Three dogs had pituitary dependent Cushing's syndrome, while the remaining one dog had iatrogenic Cushing's syndrome. Each dog had clinical features typical for Cushing's syndrome. Two of the dogs were euthanized due to progressive hypoxemia. In each dog, the serum calcium, phosphorous, blood urea nitrogen and creatinine were normal. A generalized increase in unstructured interstitial pulmonary opacity with diffuse mineralization was noted on thoracic radiographs of all dogs. In one dog, an ill-defined nodular interstitial pattern of mineralization was present. Delayed bone phase scintigraphy using 99m Technetium methylene diphosphonate documented generalized pulmonary uptake in two dogs. 99m Technetium labeled microaggregated albumin lung perfusion scans were normal in these two dogs. 99m Tc-MDP scintigraphy can provide useful information in diagnosing pulmonary mineralization in Cushingoid dogs

  13. Mineral and inorganic chemical composition of the Pernik coal, Bulgaria

    Energy Technology Data Exchange (ETDEWEB)

    Yossifova, Mariana G. [Geological Institute, Acad. G. Bonchev Str., Bl.24, Bulgarian Academy of Sciences, 1113 Sofia (Bulgaria)

    2007-11-22

    The mineral and inorganic chemical composition of five types of samples from the Pernik subbituminous coals and their products generated from the Pernik preparation plant were studied. They include feed coal, low-grade coal, high-grade coal, coal slime, and host rock. The mineral matter of the coals contains 44 species that belong mainly to silicates, carbonates, sulphates, sulphides, and oxides/hydroxides, and to a lesser extent, chlorides, biogenic minerals, and organic minerals. The detrital minerals are quartz, kaolinite, micas, feldspars, magnetite, cristobalite, spessartine, and amphibole. The authigenic minerals include various sulphides, silicates, oxihydroxides, sulphates, and carbonates. Several stages and substages of formation were identified during the syngenetic and epigenetic mineral precipitations of these coals. The authigenic minerals show the greatest diversity of mineral species as the epigenetic mineralization (mostly sulphides, carbonates, and sulphates) dominates qualitatively and quantitatively. The epigenetic mineralization was a result of complex processes occurring mostly during the late development of the Pernik basin. These processes indicate intensive tectonic, hydrothermal and volcanic activities accompanied by a change from fresh to marine sedimentation environment. Thermally altered organic matter due to some of the above processes was also identified in the basin. Most of the trace elements in the Pernik coals (Mo, Be, S, Zr, Y, Cl, Ba, Sc, Ga, Ag, V, P, Br, Ni, Co, Pb, Ca, and Ti) show an affinity to OM and phases intimately associated with OM. Some of the trace elements (Sr, Ti, Mn, Ba, Pb, Cu, Zn, Co, Cr, Ni, As, Ag, Yb, Sn, Ga, Ge, etc.) are impurities in authigenic and accessory minerals, while other trace elements (La, Ba, Cu, Ce, Sb, Bi, Zn, Pb, Cd, Nd, etc.) occur as discrete phases. Elements such as Sc, Be, Y, Ba, V, Zr, S, Mo, Ti, and Ga exceed Clarke concentrations in all of the coal types studied. It was also found that

  14. Bone mineral density in reflex sympathetic dystrophy

    International Nuclear Information System (INIS)

    Saghaphi, M.; Azarian, A.

    2002-01-01

    Objectives: Reflex Sympathetic Dystrophy (RSD) is a complex of symptoms that produce pain burning sensation, swelling, tenderness, autonomic and physical dysfunction in joint areas, particularly distal of a limb. Osteopenia or osteoporosis is an important finding that is produced gradually in involved limb. Three phase bone can scan help to diagnosis of RSD. The disease may be bilateral but is mostly unilateral. As it is believed that bone densitometry will show osteopenia more accurate than plain comparative radiographs of the involved limbs, we investigated in patients with RSD. Methods: During last three years, 8 patients with RSD were admitted. Bone mineral density was measured for 5 patients by DEXA method. The patients were 3 males and 2 females with age range of 20 to 48 years (mean 32 years). The involved areas were ankle and foot in 4, and wrist and hand in one patient. Results: Mean Bone Mineral Content (BMC) of 4 involved lower limbs were 475 +-73 grams comparing with 516+-72 grams of uninvolved limbs (p t h patient was not significant. conclusion: comparative bone mineral density in patients with RSD of the lower limbs contributes to more accurate diagnosis than plain radiographs

  15. Plant macro- and micronutrient minerals

    Science.gov (United States)

    All plants must obtain a number of inorganic mineral elements from their environment to ensure successful growth and development of both vegetative and reproductive tissues. A total of fourteen mineral nutrients are considered to be essential. Several other elements have been shown to have beneficia...

  16. Radioisotopes in plant mineral nutrition

    International Nuclear Information System (INIS)

    Singh, Bhupinder

    2016-01-01

    Extensive investigations on mineral composition of different plant species growing on various soils, helped in realizing that neither the presence nor the concentration of a mineral element in a plant can be regarded as a criterion for essentially. Plants have a limited capability for selective uptake of those mineral elements which are essential for their growth. They also take up mineral element which are not necessary for growth and may even be toxic. The mineral composition of plants growing in soils cannot, therefore, be used to establish essentially of a mineral element. Once this fact was appreciated, both water and sand culture experiments were carried out in which particular mineral elements were omitted. Von Sach and Knop are credited with reintroduction of the solution culture method using which they demonstrated the absolute requirement of ten macronutrients. As evident, these techniques made possible a more precise characterization of essentially of mineral elements and led to a better understanding of their role in plant metabolism. By the beginning of 20"t"h century importance of micronutrients like B, Mn, Cu, Mo and CI was also established

  17. Miners' strike 1984-85

    Energy Technology Data Exchange (ETDEWEB)

    Brown, L; Salter, S [comps.

    1985-01-01

    References relating to the 1984-85 UK miners strike are listed under the following subject headings: events and analysis - a chronological record; short term effects - coal stocks and supplies, electricity supplies, financial, industrial and economic; the miners and their leadership; social aspects - civil liberties, media coverage, mining communities, picketing, policing, the future; pit closures. 240 references.

  18. Minerals From the Marine Environment

    Science.gov (United States)

    Cruickshank, Michael J.

    The current interest in minerals centering on, among other things, potential shortages, long-term needs, and deep seabed nodules, accentuates the usefulness and timeliness of this little book authored by a former chairman of the British National Environmental Research Council.In less than 100 pages, the author puts into perspective the potential for producing minerals from offshore areas of the world. After introducing the reader to the ocean environment and the extraordinary variety of the nature of the seabed, the author describes in some detail the variety of minerals found there. This is done in seven separate chapters entitled ‘Bulk and Non-Metallic Minerals From the Seas’ ‘Metals From the Shallow Seas’ ‘Metals From the Deep Oceans’ ‘Minerals From Solution’ ‘Oil and Gas from the Shallow Seas’ ‘Oil and Gas From Deep Waters’ and ‘Coal Beneath the Sea.’ The remaining chapters give a brief regional review of marine minerals distribution for eight areas of significant socioeconomic structure, and a short recapitulation of special problems of mineral recovery in the marine environment including such matters as the effect of water motion on mineral processing and of international law on investments. Glossaries of geological periods and technical terms, a short list of references, and an index complete the work.

  19. Ways to defuse miners' anger

    International Nuclear Information System (INIS)

    Anon.

    1984-01-01

    The violence and riots which often occur with mining personnel are considered. The emotions and feelings which miners often experience because of their work environment are dealth with. From recognizing the pressures, the article then works to present methods to help defuse the miners' hostility and anger

  20. 77 FR 56273 - Conflict Minerals

    Science.gov (United States)

    2012-09-12

    ... auditor and to certify the audit. In addition, Section 13(p) requires the report to include a description.... Auditor Independence iii. Audit Objective 4. Recycled and Scrap Minerals a. Proposed Rules b. Comments on... Minerals Report must also identify the independent private sector auditor \\23\\ and certify the independent...

  1. Molecular Characterization of Bacterial Respiration on Minerals

    Energy Technology Data Exchange (ETDEWEB)

    Blake, Robert C.

    2013-04-26

    anomalous dispersion (MAD) phasing; 4. An acid-stable red cytochrome with a novel absorbance peak at 579 nm was purified from cell-free extracts of L. ferriphilum. Functional studies demonstrated that this cytochrome was an important component of the aerobic iron respiratory chain in this organism; 5. The specific adhesion of At. ferrooxidans to pyrite is mediated by an extracellular protein that was identified as aporusticyanin. The adhesion of At. ferrooxidans to minerals was characterized by high affinity binding that exhibited a high specificity for pyrite over other sulfide minerals. The principal biopolymer involved in this high-affinity adhesion to pyrite was isolated by mineral affinity chromatography and identified as aporusticyanin. The adhesion of purified aporusticyanin to minerals was observed to adhere to different mineral with a pattern of reactivity identical to that observed with the intact bacterium. Further, preincubation of pyrite with excess exogenous aporusticyanin served to inhibit the adherence of intact cells to the surface of the mineral, indicating that the protein and the cells adhered to the pyrite in a mutually exclusive manner. Taken together, these observations support a model where aporusticyanin located on the surface of the bacterial cell acts as a mineral-specific receptor for the initial adherence of At. ferrooxidans to solid pyrite; 6. The specific adhesion of L. ferriphilum to pyrite was mediated by a different acid-stable extracellular protein than aporusticyanin; and 7. A prototype integrating cavity absorption meter (ICAM) was assembled to determine whether this novel spectrophotometer could be used to study cellular respiration in situ.

  2. Het belang van mineraalsuppletie voor gebit en kaak [The importance of mineral supplementation for dentition and jaw

    NARCIS (Netherlands)

    Theuns, H.M.

    1995-01-01

    In this article the importance of mineral suppletion for teeth and jawbone is explained in a step-wise manner. The steps discussed are the pre-eruptive phase of teeth and the growth, adult and ageing phase of the skeleton. Mineral suppletion should be seen as a measure to prevent dental caries

  3. Method of refining mineral and shale oils, etc

    Energy Technology Data Exchange (ETDEWEB)

    1950-12-06

    A method is described for refining mineral oils, shale oils, tar oil. The oil is preferably treated with concentrated sulphuric acid, of not less than 90% by weight concentration or with chloro-sulphonic acid in order to extract the more reactive components of the oil. The solution (extract phase) is separated from the treated oil (raffinate phase) by centrifuging, characterised by centrifugally separating the extract phase from the raffinate phase before any noticeable chemical reaction with subsequent solution of acid reaction products in the raffinate phase has taken place. The acid remaining in the raffinate phase is allowed to react chemically with the more reactive constituents. The sludge formed is removed from the raffinate phase by centrifuging.

  4. On the interfacial interaction between bituminous binders and mineral surfaces as present in asphalt mixtures

    NARCIS (Netherlands)

    Fischer, H.R.; Dillingh, E.C.; Hermse, C.G.M.

    2013-01-01

    The interfacial interaction between bituminous binders and several mineral surfaces of different chemical nature as present in asphalt mixtures has been investigated using atomic force microscopy. Several dry mineral surfaces display comparable wetting with respect to the different phases present in

  5. Economic drivers of mineral supply

    Science.gov (United States)

    Wagner, Lorie A.; Sullivan, Daniel E.; Sznopek, John L.

    2003-01-01

    The debate over the adequacy of future supplies of mineral resources continues in light of the growing use of mineral-based materials in the United States. According to the U.S. Geological Survey, the quantity of new materials utilized each year has dramatically increased from 161 million tons2 in 1900 to 3.2 billion tons in 2000. Of all the materials used during the 20th century in the United States, more than half were used in the last 25 years. With the Earth?s endowment of natural resources remaining constant, and increased demand for resources, economic theory states that as depletion approaches, prices rise. This study shows that many economic drivers (conditions that create an economic incentive for producers to act in a particular way) such as the impact of globalization, technological improvements, productivity increases, and efficient materials usage are at work simultaneously to impact minerals markets and supply. As a result of these economic drivers, the historical price trend of mineral prices3 in constant dollars has declined as demand has risen. When price is measured by the cost in human effort, the price trend also has been almost steadily downward. Although the United States economy continues its increasing mineral consumption trend, the supply of minerals has been able to keep pace. This study shows that in general supply has grown faster than demand, causing a declining trend in mineral prices.

  6. Glycine Polymerization on Oxide Minerals

    Science.gov (United States)

    Kitadai, Norio; Oonishi, Hiroyuki; Umemoto, Koichiro; Usui, Tomohiro; Fukushi, Keisuke; Nakashima, Satoru

    2017-06-01

    It has long been suggested that mineral surfaces played an important role in peptide bond formation on the primitive Earth. However, it remains unclear which mineral species was key to the prebiotic processes. This is because great discrepancies exist among the reported catalytic efficiencies of minerals for amino acid polymerizations, owing to mutually different experimental conditions. This study examined polymerization of glycine (Gly) on nine oxide minerals (amorphous silica, quartz, α-alumina and γ-alumina, anatase, rutile, hematite, magnetite, and forsterite) using identical preparation, heating, and analytical procedures. Results showed that a rutile surface is the most effective site for Gly polymerization in terms of both amounts and lengths of Gly polymers synthesized. The catalytic efficiency decreased as rutile > anatase > γ-alumina > forsterite > α- alumina > magnetite > hematite > quartz > amorphous silica. Based on reported molecular-level information for adsorption of Gly on these minerals, polymerization activation was inferred to have arisen from deprotonation of the NH3 + group of adsorbed Gly to the nucleophilic NH2 group, and from withdrawal of electron density from the carboxyl carbon to the surface metal ions. The orientation of adsorbed Gly on minerals is also a factor influencing the Gly reactivity. The examination of Gly-mineral interactions under identical experimental conditions has enabled the direct comparison of various minerals' catalytic efficiencies and has made discussion of polymerization mechanisms and their relative influences possible Further systematic investigations using the approach reported herein (which are expected to be fruitful) combined with future microscopic surface analyses will elucidate the role of minerals in the process of abiotic peptide bond formation.

  7. Glycine Polymerization on Oxide Minerals.

    Science.gov (United States)

    Kitadai, Norio; Oonishi, Hiroyuki; Umemoto, Koichiro; Usui, Tomohiro; Fukushi, Keisuke; Nakashima, Satoru

    2017-06-01

    It has long been suggested that mineral surfaces played an important role in peptide bond formation on the primitive Earth. However, it remains unclear which mineral species was key to the prebiotic processes. This is because great discrepancies exist among the reported catalytic efficiencies of minerals for amino acid polymerizations, owing to mutually different experimental conditions. This study examined polymerization of glycine (Gly) on nine oxide minerals (amorphous silica, quartz, α-alumina and γ-alumina, anatase, rutile, hematite, magnetite, and forsterite) using identical preparation, heating, and analytical procedures. Results showed that a rutile surface is the most effective site for Gly polymerization in terms of both amounts and lengths of Gly polymers synthesized. The catalytic efficiency decreased as rutile > anatase > γ-alumina > forsterite > α- alumina > magnetite > hematite > quartz > amorphous silica. Based on reported molecular-level information for adsorption of Gly on these minerals, polymerization activation was inferred to have arisen from deprotonation of the NH 3 + group of adsorbed Gly to the nucleophilic NH 2 group, and from withdrawal of electron density from the carboxyl carbon to the surface metal ions. The orientation of adsorbed Gly on minerals is also a factor influencing the Gly reactivity. The examination of Gly-mineral interactions under identical experimental conditions has enabled the direct comparison of various minerals' catalytic efficiencies and has made discussion of polymerization mechanisms and their relative influences possible Further systematic investigations using the approach reported herein (which are expected to be fruitful) combined with future microscopic surface analyses will elucidate the role of minerals in the process of abiotic peptide bond formation.

  8. herbage mineral nutrition indexed as tools for rapid mineral status

    African Journals Online (AJOL)

    Administrator

    mineral indices were calculated from chemical analysis with a view to generate relevant fertilisation recommenda- tions. Although the dry .... P, and K established in temperate climate (Blanfort ..... like rotational grazing rhythms or stocking rates.

  9. Mineral mining machines

    Energy Technology Data Exchange (ETDEWEB)

    Mc Gaw, B H

    1984-01-01

    A machine for mining minerals is patented. It is a cutter loader with a drum actuating element of the worm type equipped with a multitude of cutting teeth reinforced with tungsten carbide. A feature of the patented machine is that all of the cutting teeth and holders on the drum have the identical design. This is achieved through selecting a slant angle for the cutting teeth which is the mean between the slant angle of the conventional radial teeth and the slant angle of the advance teeth. This, in turn, is provided thanks to the corresponding slant of the holders relative to the drum and (or) the slant of the cutting part of the teeth relative to their stems. Thus, the advance teeth projecting beyond the surface of the drum on the face side and providing upper and lateral clearances have the same angle of attack as the radial teeth, that is, from 20 to 35 degrees. A series of modifications of the cutting teeth is patented. One of the designs allows the cutting tooth to occupy a varying position relative to the drum, from the conventional vertical to an inverted, axially projecting position. In the last case the tooth in the extraction process provides the upper and lateral clearances for the drum on the face side. Among the different modifications of the cutting teeth, a design is proposed which provides for the presence of a stem which is shaped like a truncated cone. This particular stem is designed for use jointly with a wedge which unfastens the teeth and is placed in a holder. The latter is completed in a transverse slot thanks to which the rear end of the stem is compressed, which simplifies replacement of a tooth. Channels are provided in the patented machine for feeding water to the worm spiral, the holders and the cutting teeth themselves in order to deal with dust.

  10. Vitamins and Minerals in Kidney Disease

    Science.gov (United States)

    ... Donate A to Z Health Guide Vitamins and Minerals in Kidney Disease Tweet Share Print Email Are ... you need to know. What are vitamins and minerals? Vitamins and minerals are substances your body needs ...

  11. 76 FR 44892 - Information Collection; Locatable Minerals

    Science.gov (United States)

    2011-07-27

    ... DEPARTMENT OF AGRICULTURE Forest Service Information Collection; Locatable Minerals AGENCY: Forest... on the extension of a currently approved information collection, Locatable Minerals-36 CFR part 228...: Comments concerning this notice should be addressed to: USDA, Forest Service, Minerals and Geology...

  12. Isotope analysis of closely adjacent minerals

    International Nuclear Information System (INIS)

    Smith, M.P.

    1990-01-01

    This patent describes a method of determining an indicator of at least one of hydrocarbon formation, migration, and accumulation during mineral development. It comprises: searching for a class of minerals in a mineral specimen comprising more than one class of minerals; identifying in the mineral specimen a target sample of the thus searched for class; directing thermally pyrolyzing laser beam radiation onto surface mineral substance of the target sample in the mineral specimen releasing surface mineral substance pyrolysate gases therefrom; and determining isotope composition essentially of the surface mineral substance from analyzing the pyrolysate gases released from the thus pyrolyzed target sample, the isotope composition including isotope(s) selected from the group consisting of carbon, hydrogen, and oxygen isotopes; determining an indicator of at least one of hydrocarbon formation, migration, and accumulation during mineral development of the target mineral from thus determined isotope composition of surface mineral substance pyrolysate

  13. [Vitamins and Minerals in Oncology].

    Science.gov (United States)

    Holch, Julian Walter; Michl, Marlies; Heinemann, Volker; Erickson, Nicole

    2017-06-01

    The use of vitamins and minerals to prevent cancer as well as their supportive use in oncological patients is widespread and often occurs without the knowledge of the treating physician. Beyond general recommendations with regard to a balanced and healthy diet, no evidence exists supporting the use of vitamins and minerals in the prevention of cancer. Furthermore, the diet of oncological patients should contain vitamins and minerals of the same quantity as for healthy individuals. In particular, there is currently no rationale for a high-dosage administration of antioxidants. © Georg Thieme Verlag KG Stuttgart · New York.

  14. Utilization of Mineral Wools as Alkali-Activated Material Precursor

    Directory of Open Access Journals (Sweden)

    Juho Yliniemi

    2016-04-01

    Full Text Available Mineral wools are the most common insulation materials in buildings worldwide. However, mineral wool waste is often considered unrecyclable because of its fibrous nature and low density. In this paper, rock wool (RW and glass wool (GW were studied as alkali-activated material precursors without any additional co-binders. Both mineral wools were pulverized by a vibratory disc mill in order to remove the fibrous nature of the material. The pulverized mineral wools were then alkali-activated with a sodium aluminate solution. Compressive strengths of up to 30.0 MPa and 48.7 MPa were measured for RW and GW, respectively, with high flexural strengths measured for both (20.1 MPa for RW and 13.2 MPa for GW. The resulting alkali-activated matrix was a composite-type in which partly-dissolved fibers were dispersed. In addition to the amorphous material, sodium aluminate silicate hydroxide hydrate and magnesium aluminum hydroxide carbonate phases were identified in the alkali-activated RW samples. The only crystalline phase in the GW samples was sodium aluminum silicate. The results of this study show that mineral wool is a very promising raw material for alkali activation.

  15. Heavy mineral potential of Ramnad Sub-basin, Tamil Nadu

    International Nuclear Information System (INIS)

    Shaji, T.S.; Alam, M.

    2016-01-01

    Atomic Minerals Directorate for the Exploration and Research (AMD) is actively engaged in the surveys and exploration of heavy mineral placers along 980 km long coast of Tamil Nadu since 1950's identifying many major heavy mineral deposits/occurrences of varying grade and dimensions in the beach, coastal dunes and Teri sand environs. Though most of the coastal stretch of Tamil Nadu is fairly understood for its heavy mineral potential, some of the coastal segments of the Ramnad basin of southeastern Tamil Nadu, a storehouse of heavy mineral placer repositories need intensive exploration inputs, to understand its potential completely. The 100 km long study area falls in parts of Ramnad sub basin from Vaippar in Tuticorin to Mandapam in Ramanathpuram districts, constitutes the southern part of Cauvery basin. The unconsolidated coastal sediments of the basin is under active exploration and evaluation since 2012, in a phased manner, to link the known deposits, and completely delineate geo-spatial disposition of the heavy mineral bearing sand bodies in different environs right from the present day shoreline to the inland. Geologically, the area is a part of a long narrow strip of Tertiary/Quaternary sediments which outcrops along the southern Tamil Nadu coast. Precambrian granulites terrain of Southern Granulitic Terrain (SGT) in the hinterland area consisting of predominantly charnockites, gneisses, leptynites with numerous pegmatitic, vein quartz injections. The geomorphological features identified include Holocene Beach ridges, swales, abandoned channels, coastal dunes, and alluvial delta plains of Vaippar

  16. Refractory, Abrasive and Other Industrial Mineral Operations

    Data.gov (United States)

    Department of Homeland Security — This map layer includes refractory, abrasive, and other industrial minerals operations in the United States. The data represent commodities covered by the Minerals...

  17. Modeling CO2-Water-Mineral Wettability and Mineralization for Carbon Geosequestration.

    Science.gov (United States)

    Liang, Yunfeng; Tsuji, Shinya; Jia, Jihui; Tsuji, Takeshi; Matsuoka, Toshifumi

    2017-07-18

    Carbon dioxide (CO 2 ) capture and storage (CCS) is an important climate change mitigation option along with improved energy efficiency, renewable energy, and nuclear energy. CO 2 geosequestration, that is, to store CO 2 under the subsurface of Earth, is feasible because the world's sedimentary basins have high capacity and are often located in the same region of the world as emission sources. How CO 2 interacts with the connate water and minerals is the focus of this Account. There are four trapping mechanisms that keep CO 2 in the pores of subsurface rocks: (1) structural trapping, (2) residual trapping, (3) dissolution trapping, and (4) mineral trapping. The first two are dominated by capillary action, where wettability controls CO 2 and water two-phase flow in porous media. We review state-of-the-art studies on CO 2 /water/mineral wettability, which was found to depend on pressure and temperature conditions, salt concentration in aqueous solutions, mineral surface chemistry, and geometry. We then review some recent advances in mineral trapping. First, we show that it is possible to reproduce the CO 2 /water/mineral wettability at a wide range of pressures using molecular dynamics (MD) simulations. As the pressure increases, CO 2 gas transforms into a supercritical fluid or liquid at ∼7.4 MPa depending on the environmental temperature. This transition leads to a substantial decrease of the interfacial tension between CO 2 and reservoir brine (or pure water). However, the wettability of CO 2 /water/rock systems depends on the type of rock surface. Recently, we investigated the contact angle of CO 2 /water/silica systems with two different silica surfaces using MD simulations. We found that contact angle increased with pressure for the hydrophobic (siloxane) surface while it was almost constant for the hydrophilic (silanol) surface, in excellent agreement with experimental observations. Furthermore, we found that the CO 2 thin films at the CO 2 -hydrophilic

  18. GHGRP Minerals Sector Industrial Profile

    Science.gov (United States)

    EPA's Greenhouse Gas Reporting Program periodically produces detailed profiles of the various industries that report under the program. The profiles available for download below contain detailed analyses for the Minerals industry.

  19. Infrared spectra of mineral species

    CERN Document Server

    Chukanov, Nikita V

    2014-01-01

    This book details more than 3,000 IR spectra of more than 2,000 mineral species collected during last 30 years. It features full descriptions and analytical data of each sample for which IR spectrum was obtained.

  20. (MEPE) mineralization ability in vitro

    African Journals Online (AJOL)

    Jane

    matrix proteins and is associated with bone and teeth mineralization. We developed .... acetic acid) and bands were visualized by dynamic integrated exposure using .... approximate agreement with the expected molecular size. Purification of.

  1. Mineral exploration in developing countries

    International Nuclear Information System (INIS)

    Johnson, C.J.; Clark, A.L.

    1988-01-01

    The chapter provides an overview and comparisons of mineral exploration in Botswana and Papua New Guinea, including selection comparisons with Australia and Canada. It describes the history of exploration in Botswana and PNG. The concluding section summarizes the findings

  2. Hydrometalurgical processes for mineral complexes

    International Nuclear Information System (INIS)

    Barskij, L.A.; Danil'chenko, L.M.

    1977-01-01

    Requirements for the technology of the processing of ores including uranium ores and principal stages of the working out of technological schemes are described in brief. There are reference data on commercial minerals and ores including uranium-thorium ores, their classification with due regard for physical, chemical and superficial properties which form the basis for ore-concentrating processes. There are also presented the classification of minerals including uranium minerals by their flotation ability, flotation regimes of minerals, structural-textural characteristics of ores, genetic types of ore formations and their concentrating ability, algorithmization of the apriori evaluation of the concentration and technological diagnostics of the processing of ores. The classification of ore concentration technique is suggested

  3. VT Mineral Resources - MRDS Extract

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) MRDSVT is an extract from the Mineral Resources Data System (MRDS) covering the State of Vermont only. MRDS database contains the records provided...

  4. Mineral resources potential of Antarctica

    National Research Council Canada - National Science Library

    Splettstoesser, John F; Dreschhoff, Gisela A. M

    1990-01-01

    .... This volume of the Antarctic Research Series results from an attempt to assemble a summary of current factual knowledge and scientific data related to issues of mineral resources in Antarctica...

  5. Hydrokinesitherapy in thermal mineral water

    Directory of Open Access Journals (Sweden)

    Rendulić-Slivar Senka

    2013-01-01

    Full Text Available The treatment of clients in health spa resorts entails various forms of hydrotherapy. Due to specific properties of water, especially thermal mineral waters, hydrokinesitherapy has a positive effect on the locomotor system, aerobic capabilities of organism and overall quality of human life. The effects of use of water in movement therapy are related to the physical and chemical properties of water. The application of hydrotherapy entails precautionary measures, with an individual approach in assessment and prescription. The benefits of treatment in thermal mineral water should be emphasized and protected, as all thermal mineral waters differ in composition. All physical properties of water are more pronounced in thermal mineral waters due to its mineralisation, hence its therapeutical efficiency is greater, as well.

  6. BLM Colorado Federal Mineral Estate

    Data.gov (United States)

    Department of the Interior — Shapefile Format –This Federal Mineral Estate (Subsurface) dataset is a result of combining data sets that were collected at each BLM Colorado Field Office and using...

  7. Mineral resources of Vietnam

    Directory of Open Access Journals (Sweden)

    Kušnír Imrich

    2000-06-01

    Full Text Available Vietnam je bohatý na nerastné suroviny, ktoré sa nachádzajú prevažne na severe krajiny. Ložiská bauxitov, fosfátov, vzácnych zemín (REE, majú svetový význam. Ale i zásoby celého radu ïalších surovín (ropy, uhlia, zlata, železných rúd, chromitu, cínu, ilmenitu, medi, grafitu, atï. sú významné, ekonomicky ažite¾né a ich potenciál je obrovský. Za uvedené nerastné bohatstvo je „zodpovednᓠrozmanitá geologická stavba krajiny. Taktiež i morfológia a klíma (vlhká, tropická prispeli ku vytvoreniu niektorých ložísk (bauxity v krasových priehlbniach, atï.. Súèasná produkcia, okrem ropy (3,5 Mt/rok, zahròuje: 10,7 Mt uhlia, 3,5 Mt chromitu, asi 1 000 kg zlata, grafitu, kaolínu a mnohé iné minerály. Napriek tomu, je banícky priemysel v porovnaní so surovinovou základòou slabo vyvinutý. K jeho rozvoju urèite prispeje i úèas zahranièných spoloèností, odnedávna prítomných pri prieskume a ažbe surovín urèených pre export. Okrem struèného úvodu do geológie krajiny, obsahuje tento èlánok krátky popis nerastného bohatstva Vietnamu.

  8. Inhalation hazards to underground miners

    International Nuclear Information System (INIS)

    Beckman, R.T.

    1988-01-01

    Massive radon-daughter exposures to miners have caused lung cancer for centuries. Exposures in US uranium mines have been regulated for 15 years and, during this time, relatively few miners have been exposed to over 4 WLM year. Present trends are toward lower annual exposures and shorter working lives. The net effect has been to hold cumulative lifetime exposures well below the level at which statistically significant excess risk has been shown

  9. Sea urchin tooth mineralization: Calcite present early in the aboral plumula

    OpenAIRE

    Stock, Stuart R.; Veis, Arthur; Xiao, Xianghui; Almer, Jonathan D.; Dorvee, Jason R.

    2012-01-01

    In both vertebrate bone, containing carbonated hydroxyapatite as the mineral phase, and in invertebrate hard tissue comprised of calcium carbonate, a popular view is that the mineral phase develops from a long-lived amorphous precursor which later transforms into crystal form. Important questions linked to this popular view are: When and where is the crystallized material formed, and is amorphous solid added subsequently to the crystalline substrate? Sea urchin teeth, in which the earliest mi...

  10. Lung Cancer in uranium miners

    International Nuclear Information System (INIS)

    Zhou Chundi; Fan Jixiong; Wang Liuhu; Huang Yiehan; Nie Guanghua

    1987-01-01

    This paper analyese the clinical data of 39 uranium miners with lung cancer and of 20 patients with lung cancer who have not been exposed to uranium as control. The age of uranium miners with lung cancer was 36∼61 with an average of 48.8, nine years earlier than that of the control group (57.3). In the uranium miner patients the right lung was more susceptible to cancer than the left, the ratio being 2.5:1. However, in the control group the right lung had an equal incidence of cancer as the left lung. The relative frequency of small cell anaplastic carcinoma in uranium miner was higher than that in the control group. In the miner patients the mean occupation history was 11.1 ± 5.2 years; the exposure dose to radon and its daughters in 50% patients was 0.504J(120 WLM). The etiologic factor of lung cancer in uranium miners is strongly attributed, in addition to smoking, to the exposure to radon and its daughters in uranium mines

  11. Thermodynamics of Minerals Stable Near the Earth's Surface

    International Nuclear Information System (INIS)

    Navrotsky, Alexandra

    2003-01-01

    OAK B262 Research and Education Activities We are working on developing calorimetric techniques for sulfide minerals. We have completed calorimetric studies of (Na, K, H3O) jarosites, of Na and K jarosite -alunite solid solutions, and of Cr6+ - containing jarosites. We are now working on phases containing As and Pb. These studies are important to issues of heavy metal pollution in the environment. A number of postdocs, graduate students, and undergrads have participated in the research. We have active collaboration with Dirk Baron, faculty at California State University, Bakersfield. In a collaboration with Peter Burns, Notre Dame University, we are working on thermochemistry of U6+ minerals. Navrotsky has participated in a number of national workshops that are helping to define the interfaces between nanotechnology and earth/environmental science. Major Findings Our first finding on uranyl minerals shows that studtite, a phase containing structural peroxide ion, is thermodynamically unstable in the absence of a source of aqueous peroxide ion but is thermodynamically stable in contact with a solution containing peroxide concentrations expected for the radiolysis of water in contact with spent nuclear fuel. This work is in press in Science. We have a consistent thermodynamic data set for the (Na, K, H3O) (Al, Fe) jarosite, alunite minerals and for Cr6+ substituting for S6+ in jarosite. The latter phases represent one of the few solid sinks for trapping toxic Cr6+ in groundwater. Contributions within Discipline Better understanding of thermodynamic driving for and constraints on geochemical and environmental processes

  12. Mineral balance studies in very low birth weight infants fed human milk

    International Nuclear Information System (INIS)

    Schanler, R.J.; Abrams, S.A.; Garza, C.

    1988-01-01

    Mineral homeostasis often is disrupted in the very low birth weight (VLBW) infant fed either human milk or commercial formula that contains insufficient quantities of available calcium (Ca) and phosphorus (P). Alterations in mineral homeostasis include abnormal patterns of serum (Ca and P concentrations and alkaline phosphatase activity) and urine (Ca and P) biochemical markers, low net Ca and P retentions in comparison with intrauterine estimates of mineral accretion, and decreased bone mineral content. A two-phase study was conducted in our laboratory to test for these alterations in mineral homeostasis. In phase 1, VLBW infants fed a preparation of fortified human milk (either human milk-derived fortifier I or II or cow milk-derived fortifier) or cow milk-based formula specially designed for VLBW infants were evaluated during their hospitalization. In phase 2, after hospitalization, these infants were evaluated during the first 6 months of life when fed either their mother's milk or routine formula exclusively. The bioavailability of Ca and P from the tested preparations varied widely. Although the fortification of human milk resulted in both an improved biochemical pattern and net retention of Ca and P, optimal intrauterine mineral accretion was not achieved in any group tested. Longitudinal assessments of bone mineralization, by single photon absorptiometry, demonstrated that human milk-fed former VLBW infants had reduced bone mineral content. These investigations suggest that former VLBW infants fed human milk exclusively may be at risk for Ca and P deficiencies

  13. Study on mineral processing technology for abrasive minerals

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Seong Woong; Yang, Jung Il; Hwang, Seon Kook; Choi, Yeon Ho; Cho, Ken Joon; Shin, Hee Young [Korea Inst. of Geology Mining and Materials, Taejon (Korea, Republic of)

    1995-12-01

    Buyeo Materials in Buyeogun, Choongnam province is a company producing feldspar concentrate, but does not yet utilize the garnet as abrasive material and other useful heavy minerals wasted out from the process of feldspar ore. The purpose of this study is to develop technology and process for the recovery of garnet concentrate. As results, the garnet is defined as ferro manganese garnet. The optimum process for recovery of garnet concentrate is to primarily concentrate heavy minerals from tailings of feldspar processing. And secondly the heavy minerals concentrated is dried and separated garnet concentrate from other heavy minerals. At this time, the garnet concentrate is yield by 0.176%wt from 0.31%wt of heavy minerals in head ore. The garnet concentrate contains 33.35% SiO{sub 2}, 12.20% Al{sub 2}O{sub 3}, 28.47% Fe{sub 2}O{sub 3}, 11.96% MnO. As for utilization of abrasive materials, a fundamental data was established on technology of grinding and classification. (author). 13 refs., 47 figs., 24 tabs.

  14. Mineral commodity profiles: nitrogen

    Science.gov (United States)

    Kramer, Deborah A.

    2004-01-01

    Overview -- Nitrogen (N) is an essential element of life and a part of all animal and plant proteins. As a part of the DNA and RNA molecules, nitrogen is an essential constituent of each individual's genetic blueprint. As an essential element in the chlorophyll molecule, nitrogen is vital to a plant's ability to photosynthesize. Some crop plants, such as alfalfa, peas, peanuts, and soybeans, can convert atmospheric nitrogen into a usable form by a process referred to as 'fixation.' Most of the nitrogen that is available for crop production, however, comes from decomposing animal and plant waste or from commercially produced fertilizers. Commercial fertilizers contain nitrogen in the form of ammonium and/or nitrate or in a form that is quickly converted to the ammonium or nitrate form once the fertilizer is applied to the soil. Ammonia is generally the source of nitrogen in fertilizers. Anhydrous ammonia is commercially produced by reacting nitrogen with hydrogen under high temperatures and pressures. The source of nitrogen is the atmosphere, which is almost 80 percent nitrogen. Hydrogen is derived from a variety of raw materials, which include water, and crude oil, coal, and natural gas hydrocarbons. Nitrogen-based fertilizers are produced from ammonia feedstocks through a variety of chemical processes. Small quantities of nitrates are produced from mineral resources principally in Chile. In 2002, anhydrous ammonia and other nitrogen materials were produced in more than 70 countries. Global ammonia production was 108 million metric tons (Mt) of contained nitrogen. With 28 percent of this total, China was the largest producer of ammonia. Asia contributed 46 percent of total world ammonia production, and countries of the former U.S.S.R. represented 13 percent. North America also produced 13 percent of the total; Western Europe, 9 percent; the Middle East, 7 percent; Central America and South America, 5 percent; Eastern Europe, 3 percent; and Africa and Oceania

  15. [Mineral water as a cure].

    Science.gov (United States)

    Nocco, Priska Binz

    2008-01-01

    The treatment of diseases with mineral spring water belongs to the oldest medical therapies. The "remedy" mineral water is therefore of importance also within the pharmacy. The present pharmacy historical work examines the impact of the use of mineral waters, as well as of their dried components, as therapeutic agents in the 19th and early 20th centuries, i.e. from approx. 1810 to 1930, as well as the contributions given by pharmacists in the development and analysis of mineral water springs. Beside these aspects, the aim here is also to describe the role played by pharmacists in the production of artificial mineral water as well as in the sale and wholesale of natural and artificial mineral water. In the first part of this work the situation in Switzerland and its surrounding countries, such as Germany, France, Italy and Austria, is discussed. The second part contains a case-study of the particular situation in the Canton Tessin. It is known from the scientific literature published at that time that information on mineral water was frequently reported. Starting from the beginning of the 19th century the number of such publications increased tremendously. The major part of them were publications in scientific journals or contributions to medical and pharmaceutical manuals and reference books. In particular the spa-related literature, such as spa-guides, was of growing interest to a broad public. The inclusion of monographs into the Swiss, the Cantonal as well the foreign pharmacopoeias granted a legal frame for the mineral waters and their dried components. These works are of major importance from a pharmacy historical standpoint and represent a unique proof of historical evidence of the old medicinal drug heritage. The most frequently used therapies based on mineral waters were drinking and bath cures. Several diseases, particularly those of a chronic character, were treated with mineral waters. The positive influence of these cures on the recovery of the patients

  16. Biologically enhanced mineral weathering: what does it look like, can we model it?

    Science.gov (United States)

    Schulz, M. S.; Lawrence, C. R.; Harden, J. W.; White, A. F.

    2011-12-01

    The interaction between plants and minerals in soils is hugely important and poorly understood as it relates to the fate of soil carbon. Plant roots, fungi and bacteria inhabit the mineral soil and work symbiotically to extract nutrients, generally through low molecular weight exudates (organic acids, extracelluar polysachrides (EPS), siderophores, etc.). Up to 60% of photosynthetic carbon is allocated below ground as roots and exudates, both being important carbon sources in soils. Some exudates accelerate mineral weathering. To test whether plant exudates are incorporated into poorly crystalline secondary mineral phases during precipitation, we are investigating the biologic-mineral interface. We sampled 5 marine terraces along a soil chronosequence (60 to 225 ka), near Santa Cruz, CA. The effects of the biologic interactions with mineral surfaces were characterized through the use of Scanning Electron Microscopy (SEM). Morphologically, mycorrhizal fungi were observed fully surrounding minerals, fungal hyphae were shown to tunnel into primary silicate minerals and we have observed direct hyphal attachment to mineral surfaces. Fungal tunneling was seen in all 5 soils by SEM. Additionally, specific surface area (using a nitrogen BET method) of primary minerals was measured to determine if the effects of mineral tunneling are quantifiable in older soils. Results suggest that fungal tunneling is more extensive in the primary minerals of older soils. We have also examined the influence of organic acids on primary mineral weathering during soil development using a geochemical reactive transport model (CrunchFlow). Addition of organic acids in our models of soil development at Santa Cruz result in decreased activity of Fe and Al in soil pore water, which subsequently alters the spatial extent of primary mineral weathering and kaolinite precipitation. Overall, our preliminary modeling results suggest biological processes may be an important but underrepresented aspect of

  17. Characterization of sands and mineral clays in channel and floodplain deposits of Portuguesa river, Venezuela

    Directory of Open Access Journals (Sweden)

    Orlando José González Clemente

    2013-11-01

    Full Text Available In the main channel and floodplain of Portuguesa River were studied the mineralogical characteristics of sand and clay minerals respectively. The methodology consisted of X-ray diffraction (XRD analysis, for both mineral fractions. The results indicated the presence of mainly of quartz sands with minor amounts of chlorite, muscovite, calcite and feldspar which are considered quartz sand mature. Its origin is related to the source area and rework of soils and sediments of the floodplain. The clay fraction is characterized by the presence of 13 mineral crystalline phases consisting mainly of quartz, muscovite and chlorite, and clay minerals such as kaolinite, vermiculite, montmorillonite and nontronita. Its detrital origin may be due to mineral neoformation and inheritance. Therefore both mineral fractions consist mainly of quartz and kaolinite, which are essential components of the source area as well as the Quaternary alluvial deposits and the soils that make up the region.

  18. Study on Geology and Uranium Mineralization at Mentawa Area The Central Kalimantan

    International Nuclear Information System (INIS)

    Bambang-Soetopo

    2004-01-01

    In Mentawa Area, It was found that mineralization of U is associated with tourmaline, quartz, sulfide filling in opened fracture that parallel with schistocity WNW-ESE in direction, mm to cm in thickness, the value of radiometric is in the range of 500-11.000 e/s SPP 2 NF and maximum grade of U is 9.759,25 ppm. Goal of the study mineralogy and geology is to know about character, genesis and para genesis of the U mineralization. The method of this study is microscopic observation and microscopic study from the result of obtained by previous researchers. U mineralization is uraninite associated with molybdenite, pyrite, pyrrhotite, chalcopyrite, rutile, ilmenite and tourmaline. Based on mineral association, it was indicated that U mineralization occurred as pegmatitic pneumatholitic process. Based on those relation and mineral association it was found that Mentawa Area has occurred 4 period para genesis phase. (author)

  19. Minerals yearbook: The mineral industry of Brazil. 1988 international review

    International Nuclear Information System (INIS)

    Ensminger, H.R.

    1988-01-01

    Brazil's gross domestic product (GDP) grew only slightly in 1988 to $277 billion at current prices. The growth rate was the smallest registered since 1983, when the rate was minus 2.8%. The economy's performance was strongly influenced by a 2% to 3% decrease in industrial production and civil construction. The mineral industry, however, countered the downward trend in the industrial sector and grew a modest 1.4%. Topics discussed in the report include the following: Government policies and programs; Production; Trade; Commodity review--Metals (Aluminum, Aluminia, and Bauxite, Columbium, Copper, Gold, Iron and Steel, Manganese, Tin, Titanium); Industrial Minerals (Gem stones, Phosphate rock, Quartz); Mineral fuels (Coal, Natural gas, Petroleum, Nuclear power); Nonmineral energy sources (Alcohol, Hydroelectric)

  20. 21 CFR 573.680 - Mineral oil.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Mineral oil. 573.680 Section 573.680 Food and... Listing § 573.680 Mineral oil. Mineral oil may be safely used in animal feed, subject to the provisions of this section. (a) Mineral oil, for the purpose of this section, is that complying with the definition...

  1. Ore minerals textural characterization by hyperspectral imaging

    Science.gov (United States)

    Bonifazi, Giuseppe; Picone, Nicoletta; Serranti, Silvia

    2013-02-01

    The utilization of hyperspectral detection devices, for natural resources mapping/exploitation through remote sensing techniques, dates back to the early 1970s. From the first devices utilizing a one-dimensional profile spectrometer, HyperSpectral Imaging (HSI) devices have been developed. Thus, from specific-customized devices, originally developed by Governmental Agencies (e.g. NASA, specialized research labs, etc.), a lot of HSI based equipment are today available at commercial level. Parallel to this huge increase of hyperspectral systems development/manufacturing, addressed to airborne application, a strong increase also occurred in developing HSI based devices for "ground" utilization that is sensing units able to play inside a laboratory, a processing plant and/or in an open field. Thanks to this diffusion more and more applications have been developed and tested in this last years also in the materials sectors. Such an approach, when successful, is quite challenging being usually reliable, robust and characterised by lower costs if compared with those usually associated to commonly applied analytical off- and/or on-line analytical approaches. In this paper such an approach is presented with reference to ore minerals characterization. According to the different phases and stages of ore minerals and products characterization, and starting from the analyses of the detected hyperspectral firms, it is possible to derive useful information about mineral flow stream properties and their physical-chemical attributes. This last aspect can be utilized to define innovative process mineralogy strategies and to implement on-line procedures at processing level. The present study discusses the effects related to the adoption of different hardware configurations, the utilization of different logics to perform the analysis and the selection of different algorithms according to the different characterization, inspection and quality control actions to apply.

  2. Fluid inclusions in minerals associated to uranium mineralization in Jazida do Engenho (anomaly 09), Lagoa Real uranium province - Bahia, Brazil

    International Nuclear Information System (INIS)

    Souza, Aurelio da Silva de

    2009-01-01

    The Engenho deposit (anomaly 09) is south-eastern from Cachoeira Mine (anomaly 13), in the northern part of the Province. The uranium mineralization is associated to 'albitites' (over 70% of albite/oligoclase). Epidosites with uranium may also occur. The 'albitite' main minerals are pyroxene, gamet, albite/oligoclase feldspar, amphibole and biotite. Pyroxene, gamet, plagioclase, titanite and epidote are the minerals associated to the uranium mineralization. The fluids related to pyroxene, gamet and epidote are aqueous-saline, primary and with no carbonic phases and are constant, with small variations. They all present medium to high salinity (14 to 18wt% NaCl eq.), the higher values being related to pyroxene and the lower ones related to gamet and epidote. The fluids associated to albite/oligoclase, although aqua-saline and with no carbonic phases, show salinities much lower than in pyroxene, gamet and epidote, suggesting a intense dilution process indicating dilution toward the later minerals phases. The data suggest the pyroxene formation process occurring under a 3,5 kbar pressure condition which corresponds to approximately 10km depth. The dispersion on Th in albites, due probably to the overheating and non elastic increase in volume, precluded a reliable pressure calculation. The IF's microscopy m plagioclase gneiss (albitites host-rocks) suggests the probability of primary carbonic fluids associated to these minerals. The fluids with CO 2 showed in the gneiss maybe also be present in the albitites, probably as late or intergranular fluids. This assumption is based on the fact that signs of carbonic gases were shown during crushing tests. These tendencies suggest the occurrence of two albitization phases in this Lagoa Real area: one associated to a fluid composed by H 2 O + CO 2 + salts (in the gneiss host) and another (in the albitite) formed by an aqueous-saline phase. The data indicate the Brasiliano event as a thermal event without a predominant fluid

  3. Kinetic theory of oxygen isotopic exchange between minerals and water

    Science.gov (United States)

    Criss, R.E.; Gregory, R.T.; Taylor, H.P.

    1987-01-01

    Kinetic and mass conservation equations are used to describe oxygen isotopic exchange between minerals and water in "closed" and open hydrothermal systems. In cases where n coexisting mineral phases having different reaction rates are present, the exchange process is described by a system of n + 1 simultaneous differential equations consisting of n pseudo first-order rate equations and a conservation of mass equation. The simultaneous solutions to these equations generate curved exchange trajectories on ??-?? plots. Families of such trajectories generated under conditions allowing for different fluid mole fractions, different fluid isotopic compositions, or different fluid flow rates are connected by positive-sloped isochronous lines. These isochrons reproduce the effects observed in hydrothermally exchanged mineral pairs including 1) steep positive slopes, 2) common reversals in the measured fractionation factors (??), and 3) measured fractionations that are highly variable over short distances where no thermal gradient can be geologically demonstrated. ?? 1987.

  4. Calcium Bioavailability from Mineral Waters with Different Mineralization in Comparison to Milk and a Supplement.

    Science.gov (United States)

    Greupner, Theresa; Schneider, Inga; Hahn, Andreas

    2017-07-01

    The aim of the present study was to compare the bioavailability of calcium from 3 mineral waters with different concentrations of minerals with that of milk and a calcium supplement. A single-center, randomized controlled trial with a crossover design with 21 healthy men and women was conducted at the Institute of Food Science and Human Nutrition, Leibniz University Hannover. The participants consumed the 5 test products providing 300 mg of calcium each on 5 examination days with 1-week wash-out phases in between. Primary outcome variables were the area under the curve of serum calcium levels for 10-hour (AUC 0-10h ) and 24-hour urinary calcium excretion. In all groups, no significant differences in the AUC 0-10h of serum calcium levels as well as in the 24-hour urinary calcium excretion were observed. Likewise, mean changes in serum phosphate and urinary phosphate, as well as serum parathormone, showed no differences between the groups. Given an equivalent bioavailability of calcium in all test products, neither a high concentration of SO 4 2- or of HCO 3 influenced the bioavailability of calcium. Accordingly, the use of mineral water with high concentrations of calcium constitutes a calorie-free calcium source that can improve calcium supply.

  5. Hyperspectral analysis of clay minerals

    Science.gov (United States)

    Janaki Rama Suresh, G.; Sreenivas, K.; Sivasamy, R.

    2014-11-01

    A study was carried out by collecting soil samples from parts of Gwalior and Shivpuri district, Madhya Pradesh in order to assess the dominant clay mineral of these soils using hyperspectral data, as 0.4 to 2.5 μm spectral range provides abundant and unique information about many important earth-surface minerals. Understanding the spectral response along with the soil chemical properties can provide important clues for retrieval of mineralogical soil properties. The soil samples were collected based on stratified random sampling approach and dominant clay minerals were identified through XRD analysis. The absorption feature parameters like depth, width, area and asymmetry of the absorption peaks were derived from spectral profile of soil samples through DISPEC tool. The derived absorption feature parameters were used as inputs for modelling the dominant soil clay mineral present in the unknown samples using Random forest approach which resulted in kappa accuracy of 0.795. Besides, an attempt was made to classify the Hyperion data using Spectral Angle Mapper (SAM) algorithm with an overall accuracy of 68.43 %. Results showed that kaolinite was the dominant mineral present in the soils followed by montmorillonite in the study area.

  6. Mineral matter reactions in cokes

    Energy Technology Data Exchange (ETDEWEB)

    D. French; R. Sakurovs; M. Grigore [CSIRO Energy Technology (Australia)

    2009-07-15

    Some cokes appear to be particularly susceptible to weakening in the blast furnace. A mechanism which has been postulated to explain this is silica reduction by coke. Thus this project was initiated to ascertain the behaviour of quartz and silicates in coke with an emphasis on the role of the clay minerals. It is now possible to obtain quantitative mineralogical data and, the case of coal, to also obtain quantitative data on mineral grain size, shape and association through the use of automated electron beam image analysis techniques. This new ability can allow relationships between the amount of minerals in a coke and its reactivity to be established for the first time. Samples of five Australian coking coals were selected based upon quartz and clay mineral contents, mineral grain size and association. Samples were also provided by BlueScope Steel of coal, feed coke, and tuyere coke samples from the bosh, deadman and raceway regions of the blast furnace. The analytical work program conducted was as follows: Preparation of cokes by CSIRO; Petrography of starting coals and cokes; QEMSCAN of coals; LTA and XRD of starting coals and cokes; Coke reactivity tests (NSC and small scale); Petrography, LTA and XRD of reacted cokes; Petrographic and XRD examination of heat treated cokes. This study indicates that the NSC reactivity test does not adequately reflect the behaviour of coke in the lower part of the blast furnace. Further investigation of the behaviour of coke in the lower part of the blast furnace is required.

  7. Induced and catalysed mineral precipitation in the deep biosphere

    Science.gov (United States)

    Meister, Patrick

    2017-04-01

    Authigenic and early diagenetic minerals provide archives of past (bio)geochemical processes. In particular, isotopic signatures preserved in the diagenetic phases have been shown to document drastic changes of subsurface microbial activity (the deep biosphere) over geological time periods (Contreras et al., 2013; Meister, 2015). Geochemical and isotopic signatures in authigenic minerals may also document surface conditions and past climate. Nevertheless, such use of authigenic mineral phases as (bio)geochemical archives is often hampered by the insufficient understanding of mineral precipitation mechanisms. Accordingly the time, place and rate of mineral precipitation are often not well constrained. Also, element partitioning and isotopic fractionation may be modified as a result of the precipitation mechanism. Early diagenetic dolomite and quartz from drilled sequences in the Pacific were compared with adjacent porewater compositions and isotope signatures to gain fundamental insight into the factors controlling mineral precipitation. The formation of dolomite in carbonate-free organic carbon-rich ocean margin sediments (e.g. Peru Margin; Ocean Drilling Program, ODP, Site 1229; Meister et al., 2007) relies on the alkalinity-increase driven by anaerobic oxidation of methane and, perhaps, by alteration of clay minerals. In contrast, quartz is often significantly oversaturated in marine porewaters as the dissolved silica concentration is buffered by more soluble opal-A. For example, quartz does not form throughout a 400 metre thick sedimentary sequence in the Eastern Equatorial Pacific (ODP Site 1226; Meister et al., 2014) because it is kinetically inhibited. This behaviour can be explained by Ostwald's step rule, which suggests that the metastable phase forms faster. However, hard-lithified quartz readily forms where silica concentration drops sharply below opal-saturation. This violation of Ostwald's step rule must be driven by an auxiliary process, such as the

  8. Kinetics of mineral condensation in the solar nebula

    International Nuclear Information System (INIS)

    Grove, T.L.

    1987-01-01

    A natural extension of the type of gas-mineral-melt condensation experiments is to study the gas-mineral-melt reaction process by controlling the reaction times of appropriate gas compositions with silicate materials. In a condensing and vaporizing gas-solid system, important processes that could influence the composition of and speciation in the gas phase are the kinetics of vaporization of components from silicate crystals and melts. The high vacuum attainable in the space station would provide an environment for studying these processes at gas pressures much lower than those obtainable in experimental devices operated at terrestrial conditions in which the gas phase and mineral or melt would be allowed to come to exchange equilibrium. Further experiments would be performed at variable gas flow rates to simulate disequilibrium vapor fractionation. In this type of experiment it is desirable to analyze directly the species in the gas phase in equilibrium with the condensed silicate material. This analytical method would provide a direct determination of the species present in the gas phase. Currently, the notion of gas speciation is based on calculations from thermodynamic data. The proposed experiments require similar furnace designs and use similar experimental starting compositions, pressures, and temperatures as those described by Mysen

  9. Synthesis of magnetite nanoparticles from mineral waste

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Rohit [CSIR – Institute of Minerals and Materials Technology, Bhubaneswar 751 013 (India); Sakthivel, R., E-mail: velsak_r@yahoo.com [CSIR – Institute of Minerals and Materials Technology, Bhubaneswar 751 013 (India); Behura, Reshma; Mishra, B.K. [CSIR – Institute of Minerals and Materials Technology, Bhubaneswar 751 013 (India); Das, D. [UGC-DAE Consortium, Kolkata (India)

    2015-10-05

    Highlights: • Mineral waste becomes a valuable source for the synthesis of magnetite. • Milling helps uniform mixing of reductant with iron ore tailings. • Magnetite nanoparticles exhibit saturation magnetization of 60 emu/g. • Ag coating induces antibacterial activity of magnetite. - Abstract: Magnetite nanoparticles were synthesized from iron ore tailings – a mineral waste collected from the iron ore processing plant. Mechanical milling followed by chemical route is employed to obtain the magnetite nanoparticles from the waste. The magnetite nanoparticles were characterized by X-ray diffractometer, Field Emission Scanning Electron Microscope, Fourier Transform Infrared Spectrometer and Vibrating Sample Magnetometer. X-ray diffraction pattern confirms the existence of a magnetite phase. Field Emission Scanning Electron Microscopic (FE-SEM) pictures reveal that the particle size is below 100 nm. Fourier Transform Infrared (FTIR) spectrum shows a band at 570 cm{sup −1} for the Fe–O bond vibration. Vibrating Sample Magnetometric (VSM) study shows high saturation magnetization value of 60 emu/g at low applied magnetic field. Silver coated magnetite nanoparticles exhibits antibacterial property whereas bare magnetite does not.

  10. Mineral vein dynamics modelling (FRACS II)

    International Nuclear Information System (INIS)

    Urai, J.; Virgo, S.; Arndt, M.

    2016-08-01

    The Mineral Vein Dynamics Modeling group ''FRACS'' started out as a team of 7 research groups in its first phase and continued with a team of 5 research groups at the Universities of Aachen, Tuebingen, Karlsruhe, Mainz and Glasgow during its second phase ''FRACS 11''. The aim of the group was to develop an advanced understanding of the interplay between fracturing, fluid flow and fracture healing with a special emphasis on the comparison of field data and numerical models. Field areas comprised the Oman mountains in Oman (which where already studied in detail in the first phase), a siliciclastic sequence in the Internal Ligurian Units in Italy (closed to Sestri Levante) and cores of Zechstein carbonates from a Lean Gas reservoir in Northern Germany. Numerical models of fracturing, sealing and interaction with fluid that were developed in phase I where expanded in phase 11. They were used to model small scale fracture healing by crystal growth and the resulting influence on flow, medium scale fracture healing and its influence on successive fracturing and healing, as well as large scale dynamic fluid flow through opening and closing fractures and channels as a function of fluid overpressure. The numerical models were compared with structures in the field and we were able to identify first proxies for mechanical vein-hostrock properties and fluid overpressures versus tectonic stresses. Finally we propose a new classification of stylolites based on numerical models and observations in the Zechstein cores and continued to develop a new stress inversion tool to use stylolites to estimate depth of their formation.

  11. Mineral vein dynamics modelling (FRACS II)

    Energy Technology Data Exchange (ETDEWEB)

    Urai, J.; Virgo, S.; Arndt, M. [RWTH Aachen (Germany); and others

    2016-08-15

    The Mineral Vein Dynamics Modeling group ''FRACS'' started out as a team of 7 research groups in its first phase and continued with a team of 5 research groups at the Universities of Aachen, Tuebingen, Karlsruhe, Mainz and Glasgow during its second phase ''FRACS 11''. The aim of the group was to develop an advanced understanding of the interplay between fracturing, fluid flow and fracture healing with a special emphasis on the comparison of field data and numerical models. Field areas comprised the Oman mountains in Oman (which where already studied in detail in the first phase), a siliciclastic sequence in the Internal Ligurian Units in Italy (closed to Sestri Levante) and cores of Zechstein carbonates from a Lean Gas reservoir in Northern Germany. Numerical models of fracturing, sealing and interaction with fluid that were developed in phase I where expanded in phase 11. They were used to model small scale fracture healing by crystal growth and the resulting influence on flow, medium scale fracture healing and its influence on successive fracturing and healing, as well as large scale dynamic fluid flow through opening and closing fractures and channels as a function of fluid overpressure. The numerical models were compared with structures in the field and we were able to identify first proxies for mechanical vein-hostrock properties and fluid overpressures versus tectonic stresses. Finally we propose a new classification of stylolites based on numerical models and observations in the Zechstein cores and continued to develop a new stress inversion tool to use stylolites to estimate depth of their formation.

  12. Proton induced luminescence of minerals

    Energy Technology Data Exchange (ETDEWEB)

    Calvo del Castillo, H.; Millan, A.; Calderon, T. [Depto. Geologia y Geoquimica, Universidad Autonoma de Madrid, Ctra. Colmenar, km. 15, 28049, Madrid (Spain); Beneitez, P. [Departamento Quimica Fisica Aplicada, Universidad Autonoma de Madrid Cantoblanco, Madrid (Spain); Ruvalcaba S, J.L. [lFUNAM, Circuito de la lnvestigacion Cientifica s/n, Ciudad Universitaria, 04510 Mexico D.F. (Mexico)

    2008-07-01

    This paper presents a summary of Ionoluminescence (IL) for several minerals commonly found in jewellery pieces and/or artefacts of historical interest. Samples including silicates and non-silicates (native elements, halide, oxide, carbonate and phosphate groups) have been excited with a 1.8 MeV proton beam, and IL spectra in the range of 200- 900 nm have been collected for each one using a fiber optic coupled spectrometer. Light emissions have been related to Cr{sup 3+}, Mn{sup 2+} and Pr{sup 3+} ions, as well as intrinsic defects in these minerals. Results show the potential of IL for impurity characterization with high detection limits, local symmetry studies, and the study of the origin of minerals. (Author)

  13. Preparation of synthetic standard minerals

    International Nuclear Information System (INIS)

    Herrick, C.C.; Bustamante, S.J.; Charls, R.W.; Cowan, R.E.; Hakkila, E.A.; Hull, D.E.; Olinger, B.W.; Roof, R.B.; Sheinberg, H.; Herrick, G.C.

    1978-01-01

    A number of techniques for synthetic mineral preparations have been examined. These techniques include hot-pressing in graphite dies at moderate pressures, high-pressure, high-temperature synthesis in a piston and cylinder apparatus, isostatic pressing under helium gas pressures, hydrous mineral preparations using water as the pressure medium, explosion-generated shock waves, and radiofrequency heating. Minerals suitable for equation-of-state studies (three-inch, high-density discs), for thermodynamic property determinations (low-density powders) and for microprobe standards (fusion-cast microbeads) have been prepared. Mechanical stress-strain calculations in the piston-cylinder apparatus have been initiated and their integration with thermal stress calculations is currently under investigation

  14. New french uranium mineral species

    International Nuclear Information System (INIS)

    Branche, G.; Chervet, J.; Guillemin, C.

    1952-01-01

    In this work, the authors study the french new uranium minerals: parsonsite and renardite, hydrated phosphates of lead and uranium; kasolite: silicate hydrated of uranium and lead uranopilite: sulphate of uranium hydrated; bayleyite: carbonate of uranium and of hydrated magnesium; β uranolite: silicate of uranium and of calcium hydrated. For all these minerals, the authors give the crystallographic, optic characters, and the quantitative chemical analyses. On the other hand, the following species, very rare in the french lodgings, didn't permit to do quantitative analyses. These are: the lanthinite: hydrated uranate oxide; the α uranotile: silicate of uranium and of calcium hydrated; the bassetite: uranium phosphate and of hydrated iron; the hosphuranylite: hydrated uranium phosphate; the becquerelite: hydrated uranium oxide; the curite: oxide of uranium and lead hydrated. Finally, the authors present at the end of this survey a primary mineral: the brannerite, complex of uranium titanate. (author) [fr

  15. KeyPathwayMinerWeb

    DEFF Research Database (Denmark)

    List, Markus; Alcaraz, Nicolas; Dissing-Hansen, Martin

    2016-01-01

    , for instance), KeyPathwayMiner extracts connected sub-networks containing a high number of active or differentially regulated genes (proteins, metabolites) in the molecular profiles. The web interface at (http://keypathwayminer.compbio.sdu.dk) implements all core functionalities of the KeyPathwayMiner tool set......We present KeyPathwayMinerWeb, the first online platform for de novo pathway enrichment analysis directly in the browser. Given a biological interaction network (e.g. protein-protein interactions) and a series of molecular profiles derived from one or multiple OMICS studies (gene expression...... such as data integration, input of background knowledge, batch runs for parameter optimization and visualization of extracted pathways. In addition to an intuitive web interface, we also implemented a RESTful API that now enables other online developers to integrate network enrichment as a web service...

  16. Radon risk in ore miners

    International Nuclear Information System (INIS)

    Beno, M.

    1997-01-01

    Underground workers are exposed to various clastogenic agents. One of these agents, radon, attracts attention of recent research as it causes lung cancer in the population occupationally exposed to its various concentrations especially in mine air of uranium mines or ore mines. This paper is a pilot study in which the numbers of chromosomal aberrations (CA) in lymphocytes of ore mines (Nizna Slana-iron ore, Hnusta-talc ore) located in east central Slovakia were followed and related to the lifetime underground radon exposure and to lifetime smoking. Seventy miners volunteering after an informed consent served as donors of venous blood. Twenty healthy pro-bands, age matched with the miners, which never worked underground (mostly clerks) served as donors of control blood samples. The exposure to radon and smoking has been estimated according to working-records and personal anamnesis. The findings unequivocally showed a small but statistically significant clastogenic effect of the exposure to underground environment of the mines concerned. This study has shown also a small but significant influence of smoking, which in the subgroup of miners working underground less than 1500 shifts may have acted synergically with the underground exposure. It was concluded tat: (1) Significantly higher counts of chromosomal aberrations in lymphocytes of 70 miners than in an age matched control group of 20 white-collar workers were found; (2) The higher counts of chromosomal aberrations could be ascribed to underground exposure of miners and to smoking; (3) The positive dependence of the number of chromosomal aberrations from the exposure to smoking was loose and it was expressed by significantly higher chromosomal aberrations counts in the group of miners working less than 1500 shifts underground; (4) A dependence of chromosomal aberrations counts from the exposure to radon could not be assessed. At relatively low numbers of pro-bands in subgroups it was not ruled out the confounding

  17. International availability of energy minerals

    Energy Technology Data Exchange (ETDEWEB)

    White, N A

    1978-09-01

    Whereas the ultimate world supply of energy minerals--defined as fossil fuels and fissile materials--is controlled by geological factors, the actual supply at any particular time is controlled by economic feasibility, technological innovations and/or political decisions. This paper identifies and discusses the principal uncertainties surrounding the international availability of energy minerals from now until the end of the century. Genuine shortages of energy minerals are now of a very long-term nature, whereas artificial ones may occur at any time and have a serious effect on the world economy due to the dependence of most OECD countries on imports of energy minerals. This paper argues that events over the last decade will progressively lead to a major, long-lasting transformation of the energy scene worldwide. This transformation will encompass demand, in terms of conservation and efficiency, the supply mix of the various energy minerals, the supply system and the structure of the different energy industries. It is already affecting the role of governments and reaching into the question of national sovereignty, thereby making energy minerals a key area of international relations. In all these respects, this paper concludes that we have entered an era that is quite different from those we have experienced in the past. As well as requiring many new technological innovations, more importantly, attention must be focused on the development of new approaches to meeting the energy industries' capital requirements in the decades ahead--first, because of the changing character of the energy industries and the magnitude of their financial requirements; secondly, because of the nature of the uncertainties with which they are faced; and thirdly, because of the constantly shifting and increasingly complex world capital market conditions.

  18. Sorption of cesium onto the mineral phases and cement

    Data.gov (United States)

    U.S. Environmental Protection Agency — Numerical data corresponding to manuscript figures. This dataset is associated with the following publication: Kaminski, M., C. Mertz, J. Jerden, M. Kalensky, N....

  19. Economical characteristics of base types of minerals. 1. Metallic minerals

    International Nuclear Information System (INIS)

    Khasanov, A.Kh.

    1990-01-01

    Metallic minerals is raw materials base of black and colour metallurgy. In this article of book author describes the group of black metals (iron, manganese, chromium), group of tempers (titanium, vanadium, nickel, cobalt, molybdenum, tungsten), colour metals (copper, lead, zinc, aluminium, tin, mercury, antimony, bismuth) and etc.

  20. Fault rocks and uranium mineralization

    International Nuclear Information System (INIS)

    Tong Hangshou.

    1991-01-01

    The types of fault rocks, microstructural characteristics of fault tectonite and their relationship with uranium mineralization in the uranium-productive granite area are discussed. According to the synthetic analysis on nature of stress, extent of crack and microstructural characteristics of fault rocks, they can be classified into five groups and sixteen subgroups. The author especially emphasizes the control of cataclasite group and fault breccia group over uranium mineralization in the uranium-productive granite area. It is considered that more effective study should be made on the macrostructure and microstructure of fault rocks. It is of an important practical significance in uranium exploration

  1. Platinum-group element mineralization

    International Nuclear Information System (INIS)

    Gruenewaldt, G.

    1985-01-01

    The purpose of this investigation is to determine the geological processes responsible for the abnormal enrichment of the platinum-group elements (PGE) in the mineralized layers of the Bushveld Complex. Questions asked are: what processes caused enrichment of the Bushveld magma in the PGE ; by what processes were these PGE concentrated in the mineralized layers ; was contamination of the Bushveld magma from external sources important in the formation of the PGE enriched layers ; what are the effects of fractional crystallization on the PGE ratios

  2. Significance, mechanisms and environmental implications of microbial bio-mineralization

    International Nuclear Information System (INIS)

    Benzerara, K.; Miot, J.; Morin, G.; Ona-Nguema, G.; Skouri-Panet, F.; Ferard, C.

    2011-01-01

    Microorganisms can mediate the formation of minerals by a process called bio-mineralization. This process offers an efficient way to sequester inorganic pollutants within relatively stable solid phases. Here we review some of the main mechanisms involved in the mediation of mineral precipitation by microorganisms. This includes supersaturation caused by metabolic activity, the triggering of nucleation by production of more or less specific organic molecules, and the impact of mineral growth. While these processes have been widely studied in the laboratory, assessment of their importance in the environment is more difficult. We illustrate this difficulty using a case study on an As-contaminated acid mine drainage located in the South of France (Carnoules, Gard). In particular, we explore the potential relationships that might exist between microbial diversity and mineral precipitation. The present review, far from being exhaustive, highlights some recent advances in the field of bio-mineralogy and provides non-specialists an introduction to some of the main approaches and some questions that remain unanswered. (authors)

  3. Characterization of uranium minerals from Chihuahua using synchrotron radiation

    International Nuclear Information System (INIS)

    Burciaga V, D. C.; Reyes C, M.; Reyes R, A.; Renteria V, M.; Esparza P, H.; Fuentes C, L.; Fuentes M, L; Silva S, M.; Herrera P, E.; Munoz, A.; Montero C, M. E.

    2010-01-01

    Uranium mineral deposits in the vicinity of Chihuahua City (northern Mexico) have motivated a multidisciplinary investigation due to their tech no-environmental importance. It provides a broad scope study of representative mineral samples extracted from the San Marcos deposit, located northwest of Chihuahua City. The zone of interest is the source of the Sacramento River, which runs at Chihuahua City. The high uranium content of the San Marcos deposit, which was formed by hydrothermal mineralization, has resulted in elevated levels of uranium in surface and ground water, fish, plants and sediments in this region. Mineral identification of the uranium-bearing phases was accomplished with a suite of techniques. Among these phases are those called meta tyuyamunite (Ca(UO 2 ) 2 (VO 4 ) 2 ·3-5 H 2 O) and becquerelite [Ca(UO 2 ) 6 O 4 (OH) 6 ·8(H 2 O)]. It was decided to study an almost pure meta tyuyamunite sample extracted from Pena Blanca, Chihuahua uranium ore and to synthesize the becquerelite, using a modified procedure from a published one. In the current work the crystal structure of meta tyuyamunite is presented, resolved by the Rietveld refinement. Both samples were studied by X-ray absorption fine structure at beamline 2-3, Stanford Synchrotron Radiation Light source. In the present work both the spectra and extended X-ray absorption fine structure parameters are presented. (Author)

  4. Characterization of uranium minerals from Chihuahua using synchrotron radiation

    Energy Technology Data Exchange (ETDEWEB)

    Burciaga V, D. C.; Reyes C, M.; Reyes R, A.; Renteria V, M.; Esparza P, H.; Fuentes C, L.; Fuentes M, L; Silva S, M.; Herrera P, E.; Munoz, A.; Montero C, M. E. [Centro de Investigacion en Materiales Avanzados, S. C., Miguel de Cervantes 120, Complejo Industrial Chihuahua, Chihuahua (Mexico)

    2010-02-15

    Uranium mineral deposits in the vicinity of Chihuahua City (northern Mexico) have motivated a multidisciplinary investigation due to their tech no-environmental importance. It provides a broad scope study of representative mineral samples extracted from the San Marcos deposit, located northwest of Chihuahua City. The zone of interest is the source of the Sacramento River, which runs at Chihuahua City. The high uranium content of the San Marcos deposit, which was formed by hydrothermal mineralization, has resulted in elevated levels of uranium in surface and ground water, fish, plants and sediments in this region. Mineral identification of the uranium-bearing phases was accomplished with a suite of techniques. Among these phases are those called meta tyuyamunite (Ca(UO{sub 2}){sub 2}(VO{sub 4}){sub 2{center_dot}}3-5 H{sub 2}O) and becquerelite [Ca(UO{sub 2}){sub 6}O{sub 4}(OH){sub 6{center_dot}}8(H{sub 2}O)]. It was decided to study an almost pure meta tyuyamunite sample extracted from Pena Blanca, Chihuahua uranium ore and to synthesize the becquerelite, using a modified procedure from a published one. In the current work the crystal structure of meta tyuyamunite is presented, resolved by the Rietveld refinement. Both samples were studied by X-ray absorption fine structure at beamline 2-3, Stanford Synchrotron Radiation Light source. In the present work both the spectra and extended X-ray absorption fine structure parameters are presented. (Author)

  5. Thermodynamic properties of minerals: Macroscopic and microscopic approaches

    International Nuclear Information System (INIS)

    Richet, P.; Gillet, P.; Fiquet, G.

    1992-01-01

    Thermodynamic modeling of experimental or natural-phase equilibria has become an integral part of petrology. In this respect, the isobaric heat capacity (C p ) has manifold importance. First, C p data constitute the basis of third-law determinations of the entropy of minerals. Second, these data are needed to calculate the variation with temperature of the entropy, the entropy, and the Gibbs free energy. As a result, it necessary to know accurately heat capacities when retrieving thermodynamic information from phase equilibria data, especially when trying to separate the effects of the enthalpies and entropies of transformation. In this paper, we broadly review the main empiricial and theoretical aspects of the heat capacity of minerals. We begin with a brief review of the three main techniques that are currently in use for determining heat capacities from 0 to 2000 K, namely, adiabatic, differential scanning (DSC), and drop colarimetry, paying attention to the experimental constraints that limit measurements to certain conditions. When minerals can be subjected at best to limited calorimetric measurements, either because of lack of gram-sized samples or of instability at high temperatures (as if often the case with high-pressure minerals), other ways have to be found for predicting standard entropies and high-temperature properties. The validity of empiricial methods of prediction of the heat capacity as a function of temperature and composition will thus be discussed

  6. A facile in vitro model to study rapid mineralization in bone tissues.

    Science.gov (United States)

    Deegan, Anthony J; Aydin, Halil M; Hu, Bin; Konduru, Sandeep; Kuiper, Jan Herman; Yang, Ying

    2014-09-16

    Mineralization in bone tissue involves stepwise cell-cell and cell-ECM interaction. Regulation of osteoblast culture microenvironments can tailor osteoblast proliferation and mineralization rate, and the quality and/or quantity of the final calcified tissue. An in vitro model to investigate the influencing factors is highly required. We developed a facile in vitro model in which an osteoblast cell line and aggregate culture (through the modification of culture well surfaces) were used to mimic intramembranous bone mineralization. The effect of culture environments including culture duration (up to 72 hours for rapid mineralization study) and aggregates size (monolayer culture as control) on mineralization rate and mineral quantity/quality were examined by osteogenic gene expression (PCR) and mineral markers (histological staining, SEM-EDX and micro-CT). Two size aggregates (on average, large aggregates were 745 μm and small 79 μm) were obtained by the facile technique with high yield. Cells in aggregate culture generated visible and quantifiable mineralized matrix within 24 hours, whereas cells in monolayer failed to do so by 72 hours. The gene expression of important ECM molecules for bone formation including collagen type I, alkaline phosphatase, osteopontin and osteocalcin, varied temporally, differed between monolayer and aggregate cultures, and depended on aggregate size. Monolayer specimens stayed in a proliferation phase for the first 24 hours, and remained in matrix synthesis up to 72 hours; whereas the small aggregates were in the maturation phase for the first 24 and 48 hour cultures and then jumped to a mineralization phase at 72 hours. Large aggregates were in a mineralization phase at all these three time points and produced 36% larger bone nodules with a higher calcium content than those in the small aggregates after just 72 hours in culture. This study confirms that aggregate culture is sufficient to induce rapid mineralization and that aggregate

  7. Calc-silicate mineralization in active geothermal systems

    Energy Technology Data Exchange (ETDEWEB)

    Bird, D.K.; Schiffman, P.; Elders, W.A.; Williams, A.E.; McDowell, S.D.

    1983-01-01

    The detailed study of calc-silicate mineral zones and coexisting phase relations in the Cerro Prieto geothermal system were used as examples for thermodynamic evaluation of phase relations among minerals of variable composition and to calculate the chemical characteristics of hydrothermal solutions compatible with the observed calc-silicate assemblages. In general there is a close correlation between calculated and observed fluid compositions. Calculated fugacities of O{sub 2} at about 320{degrees}C in the Cerro Prieto geothermal system are about five orders of magnitude less than that at the nearby Salton Sea geothermal system. This observation is consistent with the occurrence of Fe{sup 3+} rich epidotes in the latter system and the presence of prehnite at Cerro Prieto.

  8. MINERAL WATERS IN RHEUMATOID ARTHRITIS

    Directory of Open Access Journals (Sweden)

    BORGES, TIAGO

    2013-02-01

    Full Text Available Background: Rheumatoid arthritis (RA is an autoimmune disorder affecting nearly 1% of adult population. First-line therapies include disease-modifying antirheumatic drugs, but creno-balneotherapyis often prescribed in rheumatic disorders and RA is no exception. Objectives: To know the efficacy of creno-balneotherapy in RA. Methods: A Medline based search was made using MeSH terms “balneology” and “rheumatoid arthritis”. Articles concerning the use of mineral waters in RA treatment were included. Results: In RA, two traditional ways of employing mineral waters are commonly used: immersion and peliotherapy. Each owns their benefits to non-specific or hydrotherapeutic effects and specific or crenotherapeutic effects. Mineral waters must be regarded as an adjuvant therapy in quiescent, stable or non-progressive RA. Significant benefits have been accomplished with radonenriched and sulphurous waters. Isothermal or hyperthermal waters should be preferred. Conclusions: Although there is a global lack of evidence, mineral waters are a safe and effective therapy to be considered in RA.

  9. Marine minerals: The Indian perspective

    Digital Repository Service at National Institute of Oceanography (India)

    Gujar, A.R.; Nath, B.N.; Banerjee, R.

    the Konkan Coast, Maharashtra. The future demand for economic minerals and metals for the year 2000 vis-a-vis the production of material in the last twelve years has been calculated, and in light of the above, the importance and chances of offshore...

  10. Oceans: Geochemistry and mineral resources

    Digital Repository Service at National Institute of Oceanography (India)

    Joao, H.M.; Paropkari, A.L.

    , Indian became the first country to have been allocated exclusive rights of exploration in the pioneer area in the Central Indian Ocean Basin. Presently world wide some of the near-shore deposits are being exploited. However, the mining for other mineral...

  11. Mineral evolution and Earth history

    Science.gov (United States)

    Bradley, Dwight C.

    2015-01-01

    The field of mineral evolution—a merger of mineralogy and Earth history—coalesced in 2008 with the first of several global syntheses by Robert Hazen and coworkers in the American Mineralogist. They showed that the cumulative abundance of mineral species has a stepwise trend with first appearances tied to various transitions in Earth history such as the end of planetary accretion at ca. 4.55 Ga and the onset of bio-mediated mineralogy at ca. >2.5 Ga. A global age distribution is best established for zircon. Observed abundance of zircon fluctuates through more than an order of magnitude during successive supercontinent cycles. The pulse of the Earth is also recorded, albeit imperfectly, by the 87Sr/86Sr composition of marine biogenic calcite; the Sr-isotopic ratio of this mineral reflects the balance of inputs of primitive strontium at mid-ocean ridges and evolved strontium that drains off the continents. A global mineral evolution database, currently in the works, will greatly facilitate the compilation and analysis of extant data and the expansion of research in mineralogy outside its traditional bounds and into more interdisciplinary realms.

  12. Lagoa Real design - Mineral engineering

    International Nuclear Information System (INIS)

    Forman, J.M.A.

    1982-01-01

    This paper presents the works realized, in course and to realize of Lagoa Real Design, including the works for implantation of Mineral-Industrial complex with the production capacity of 1.000 ton of U sub(3) O sub(8) per year from 1988. (author)

  13. Impact of mineral resource depletion

    CSIR Research Space (South Africa)

    Brent, AC

    2006-09-01

    Full Text Available In a letter to the editor, the authors comment on BA Steen's article on "Abiotic Resource Depletion: different perceptions of the problem with mineral deposits" published in the special issue of the International Journal of Life Cycle Assessment...

  14. Minerals Industry' 97. Survey report

    International Nuclear Information System (INIS)

    1997-01-01

    The aim of this annual survey is to provide timely and accurate financial data such as production, price movements, profitability, distribution of assets by activity, employment and labour cost and taxation on the Australian minerals industry. It aims to facilitate more informed debate on the industry's role and importance in the economy. The report also includes information on the safety and health performance and overseas exploration expenditure of the minerals industry. This twenty-first survey relates to the year ended 30 June 1997. The proportion of activity covered in this year's survey is comparable with the 1996 survey. The mineral industry is defined as including exploration for, extraction and primary processing of minerals in Australia. The oil, gas, iron and steel industries are excluded. As for the uranium industry, increased mine capacity over the medium term saw a switch away from spot market purchases to long term contracts for uranium in 1996. This, coupled with announced releases from the US stockpile, saw downward pressure on spot market prices for uranium during 1996/97. The average spot market price for U 3 O 8 fell by an average of 6 percent during 1996/97 and was approximately 16 percent lower than three years ago. General uncertainty over the future profitability of coal industry is compounded by the likely softness of future coal prices

  15. In situ evidence of mineral physical protection and carbon stabilization revealed by nanoscale 3-D tomography

    Science.gov (United States)

    Weng, Yi-Tse; Wang, Chun-Chieh; Chiang, Cheng-Cheng; Tsai, Heng; Song, Yen-Fang; Huang, Shiuh-Tsuen; Liang, Biqing

    2018-05-01

    An approach for nanoscale 3-D tomography of organic carbon (OC) and associated mineral nanoparticles was developed to illustrate their spatial distribution and boundary interplay, using synchrotron-based transmission X-ray microscopy (TXM). The proposed 3-D tomography technique was first applied to in situ observation of a laboratory-made consortium of black carbon (BC) and nanomineral (TiO2, 15 nm), and its performance was evaluated using dual-scan (absorption contrast and phase contrast) modes. This novel tool was then successfully applied to a natural OC-mineral consortium from mountain soil at a spatial resolution of 60 nm, showing the fine structure and boundary of OC, the distribution of abundant nano-sized minerals, and the 3-D organo-mineral association in situ. The stabilization of 3500-year-old natural OC was mainly attributed to the physical protection of nano-sized iron (Fe)-containing minerals (Fe oxyhydroxides including ferrihydrite, goethite, and lepidocrocite), and the strong organo-mineral complexation. In situ evidence revealed an abundance of mineral nanoparticles, in dense thin layers or nano-aggregates/clusters, instead of crystalline clay-sized minerals on or near OC surfaces. The key working minerals for C stabilization were reactive short-range-order (SRO) mineral nanoparticles and poorly crystalline submicron-sized clay minerals. Spectroscopic analyses demonstrated that the studied OC was not merely in crisscross co-localization with reactive SRO minerals; there could be a significant degree of binding between OC and the minerals. The ubiquity and abundance of mineral nanoparticles on the OC surface, and their heterogeneity in the natural environment may have been severely underestimated by traditional research approaches. Our in situ description of organo-mineral interplay at the nanoscale provides direct evidence to substantiate the importance of mineral physical protection for the long-term stabilization of OC. This high-resolution 3-D

  16. Isolation of ionium (230Th) from a pitchblende mineral sample

    International Nuclear Information System (INIS)

    Ejaz, M.

    1974-01-01

    A method is suggested for separating ionium ( 230 Th) from a pitchblende mineral sample. It is based on the coextraction of uranium and thorium into 0.10 M 4-(5-nonyl)pyridine oxide/xylene from very dilute nitric acid. Thorium is selectively back extracted from the organic phase followed by a cation exchange concentration and purification step. The ionium separated had a 230 Th : 232 Th ratio of 0.085 +- 0.001. (orig.) [de

  17. Radiological hazards to uranium miners

    International Nuclear Information System (INIS)

    1990-05-01

    The purpose of the present document is to review and assess the occupational hazards to uranium miners in Canada. Amendments to regulations set the maximum permissible dose to uranium miners at 50 mSv per year. Uranium miners are exposed to radon and thoron progeny, external gamma radiation and long-lived alpha-emitting radionuclides in dust. The best estimate for the lifetime risk of inhaled radon progeny is about 3 x 10 -4 lung cancers per WLM for the average miner, with a range of uncertainty from about 1 -6 x 10 -4 per WLM. This central value is nearly twice as high as that recommended by the ICRP in 1981. The probability of serious biological consequences following exposure to external gamma rays is currently under review but is expected to be in the range of 3 - 6 x 10 -2 Sv -1 . Dosimetric calculations indicate that the stochastic risks per WLM of thoron progeny are about one-third of those for radon progeny. The annual limits on intake of inhaled ore dusts recommended by the ICRP are probably too low by at least a factor of two for the type of ore and dust normally encountered in underground uranium mines in Ontario; this is due in part to the fact that the average diameter of these dusts is five times greater than the value used by the ICRP. Radiological exposures of uranium miners in Canada were reviewed. The biological impact of these exposures were compared with those of conventional accidents on the basis of the years of normal life expectancy that are lost or seriously impaired due to occupational hazards. The objectives in considering all occupational risks are to reduce the total risk from all causes and to use funds spent for health protection as effectively as possible

  18. Microprobe to closely examine minerals

    International Nuclear Information System (INIS)

    2006-01-01

    The University of South Australia will develop synchrotron-based technology that can determine the structure and chemical composition of mineral samples at microscopic levels. The planned multi-analysis synchrotron X-ray facility Beam-line 11 is for implementing on the Australian Synchrotron. UniSA's Applied Centre for Structural and Synchrotron Studies (ACeSSS) will use Beamline 11 to shed new light on factors that constrain recoveries of copper and gold from typical copper ores. ACeSSS director Professor Andrea Gerson is working with an international team and the Australian Synchrotron on the design of Beamline 11. According to Gerson, there is scope to improve processing and/or increase recoveries in copper, gold and valueless pyrite either through separation, smelting, leaching or electro-processing. Using synchrotron technology, researchers will determine the structure and chemical composition of mineral samples to understand the fundamental behaviour of these materials in order to identify process and : environmental benefits. Three different strategies will be employed: tracing the movement of gold through the mineral processing chain to optimise and increase gold recovery; examining the surface layers formed when copper is leached from the mineral, chalcopyrite, to enhance the understanding of this surface layer formation and ultimately maximise cop-per recovery; and improving environmental remediation by understanding the mineralisation process during acid-rock drainage. ACeSSS will work with the minerals and environmental remediation sectors, building on the I establishment of the Cooperative Research Centre for Contamination Assessment and Remediation of the Environment, and cementing close collaboration with UniSA's Ian Wark Research Institute. Contributions from the SA Premier's Science and Research Fund, BHP Billiton and Rio Tinto, synchrotron partners Advanced Light Source (USA) and the Canadian Light Source Funding totalling $1.38m are available for

  19. Mineral Precipitation in Fractures: Multiscale Imaging and Geochemical Modeling

    Science.gov (United States)

    Hajirezaie, S.; Peters, C. A.; Swift, A.; Sheets, J. M.; Cole, D. R.; Crandall, D.; Cheshire, M.; Stack, A. G.; Anovitz, L. M.

    2017-12-01

    For subsurface energy technologies such as geologic carbon sequestration, fractures are potential pathways for fluid migration from target formations. Highly permeable fractures may become sealed by mineral precipitation. In this study, we examined shale specimens with existing cemented fractures as natural analogues, using an array of imaging methods to characterize mineralogy and porosity at several spatial scales. In addition, we used reactive transport modeling to investigate geochemical conditions that can lead to extensive mineral precipitation and to simulate the impacts on fracture hydraulic properties. The naturally-cemented fractured rock specimens were from the Upper Wolfcamp formation in Texas, at 10,000 ft depth. The specimens were scanned using x-ray computed tomography (xCT) at resolution of 13 microns. The xCT images revealed an original fracture aperture of 1.9 mm filled with several distinct mineral phases and vuggy void regions, and the mineral phase volumes and surface areas were quantified and mapped in 3D. Specimens were thin-sectioned and examined at micron- and submicron-scales using petrographic microscopy (PM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), and small angle X-ray scattering (SAXS). Collectively these methods revealed crystals of dolomite as large as 900 microns in length overlain with a heterogeneous mixture of carbonate minerals including calcite, dolomite, and Fe-rich dolomite, interspersed at spatial scales as small as 5 microns. In addition, secondary precipitation of SiO2 was found to fill some of the void space. This multiscale imaging was used to inform the reactive transport modeling employed to examine the conditions that can cause the observed mineral precipitation in fractures at a larger scale. Two brines containing solutions that when mixed would lead to precipitation of various carbonate minerals were simulated as injectants into a fracture domain. In particular, the competing

  20. Proceedings of XXIV international mineral processing congress

    Energy Technology Data Exchange (ETDEWEB)

    Wang Dianzuo; Sun Chuan Yao; Wang Fu Liang; Zhang Li Cheng; Han Long (eds.)

    2008-07-01

    Topics covered in volume 1 include applied mineralogy, comminution, classification, physical separation, flotation chemistry, sulphide flotation, non-sulphide flotation and reagent in mineral industry. Volume 2 covers processing of complex ores, processing of industrial minerals and coal, solid liquid separation, dispersion and aggregation, process simulation, expert systems and control of mineral processing, biohydrometallurgy, and mineral chemical processing. Volume 3 contains powder technology, mineral materials, treatment and recycling for solid wastes, waste water treatment, secondary resource recovery, soil remediation, concentrator engineering and process design, and application of mineral processing in related industry. It includes a CD-ROM of the proceedings.

  1. U.S. Geological Survey Mineral Resources Program—Mineral resource science supporting informed decisionmaking

    Science.gov (United States)

    Wilkins, Aleeza M.; Doebrich, Jeff L.

    2016-09-19

    The USGS Mineral Resources Program (MRP) delivers unbiased science and information to increase understanding of mineral resource potential, production, and consumption, and how mineral resources interact with the environment. The MRP is the Federal Government’s sole source for this mineral resource science and information. Program goals are to (1) increase understanding of mineral resource formation, (2) provide mineral resource inventories and assessments, (3) broaden knowledge of the effects of mineral resources on the environment and society, and (4) provide analysis on the availability and reliability of mineral supplies.

  2. Giemsa as a fluorescent dye for mineralizing bone-like nodules in vitro

    International Nuclear Information System (INIS)

    Querido, W; Farina, M; Balduino, A

    2012-01-01

    Giemsa was first used as a fluorescent dye for mineralized bone and cartilage in tissue sections. The aim of this study was to establish the use of Giemsa as a fluorescent dye for mineralizing bone-like nodules produced in cell cultures. Osteoblasts were grown under mineralizing conditions for 14 days, producing typical bone-like nodules. Upon staining with Giemsa stock solution for 1 min, the mineralizing nodules could be selectively visualized emitting intense green and red fluorescence when observed under blue and green illumination, respectively. The textural details of the nodules were clearly observed under fluorescence microscopy, allowing to identify regions with different degrees of mineralization. The mineralized nature of the nodules was confirmed using von Kossa's method, Alizarin Red S staining and x-ray mapping for Ca and P in a scanning electron microscope, showing a strong correlation between the mineralizing and the fluorescent nodules. The selective fluorescence was related to the mineral phase, being absent in decalcified samples. The use of Giemsa as a fluorescent dye for mineralizing bone-like nodules presents a simple alternative method to quickly analyze biomineralization assays in vitro under fluorescence microscopy, particularly in the biological evaluation of biomaterials. (communication)

  3. Effect of Oxytetracycline on In vitro Mineralization and Demineralization Reactions in the Absence and Presence of Collagen

    Directory of Open Access Journals (Sweden)

    Monica Kakkar

    2017-11-01

    Full Text Available Introduction: Oxytetracycline and its derivatives are routinely used to treat various ailments have also been shown to inhibit embryonic bone formation, mineralization in pregnant female rats and parathyroid hormone induced demineralization of bones. Oxytetracycline has also been routinely used as bone fluorochrome to study bone metabolism. However, despite the above observations, its mechanism of action is not clearly understood. Some studies tend to suggest that it acts by inhibiting collagen biosynthesis while others indicate that it acts without influencing collagen metabolism. Aim: To study the mechanism by which oxytetracycline influences the mineralization and demineralization reactions. Materials and Methods: Homogeneous and heterogeneous systems of in vitro mineralization under physiological conditions of temperature, pH and ionic strength were used to investigate the effect of oxytetracycline not only on initial mineral phase formation but also on its subsequent growth or demineralization. In the Homogenous system, supersaturated conditions with respect to calcium and phosphate ions were employed to study their precipitation as mineral phase resembling hydroxyapatite in nature. However, in the heterogeneous system, collagen isolated from sheep tendons was used to induce identical mineral phases under saturated conditions with respect to calcium and phosphate ions prevailing in the body fluids. Results: The study demonstrated that in the homogeneous reaction system (mineralization in the absence of collagen oxytetracycline inhibited both the initial mineral phase formation and its subsequent growth without influencing its demineralization. However, in the heterogeneous system, oxytetracycline was found to inhibit not only the initial mineralization but also its subsequent growth or demineralization. Conclusion: Oxytetracycline acted like crystal poisons to inhibit the mineralization and demineralization reactions by tightly associating

  4. Magmatic evolution and REE mineralization in the early Cambrian Jbel Boho igneous complex in the Bou Azzer inlier (Anti-Atlas/Morocco)

    OpenAIRE

    Benaouda, Rachid

    2015-01-01

    The igneous rocks of Jbel Boho emerged in three phases: an initial phase with alkaline volcanism followed by the intrusion of a syenitic pluton and later the emplacement of a dyke swarm. The Jbel Boho alkaline complex shows some interesting aspects of hydrothermal REE mineralization in the late differentiation stage. REE mineralization is found in a rhyolitic dyke and some late hydrothermal veins. Synchysite-(Ce), which was identified by EPMA analysis, is the main REE mineral.

  5. Australian mineral industry annual review for 1982

    Energy Technology Data Exchange (ETDEWEB)

    1984-01-01

    The Australian mineral industry annual review records the activities and development of the Australian mineral industry and reports production, consumption, treatment, trade, prices, new developments, exploration and resources for mineral commodities including fuels, and summarises equivalent developments abroad. The present volume reviews activities and developments in 1982. Part 1 (General Review) - after briefly surveying the world mineral industry, summarises developments in the Australian mineral industry as a whole, under the headings: the industry in the national economy; important recent developments; production; overseas trade; prices; exploration expenditure; investment; income tax; royalties; structural data; wages and salaries; industrial disputes; and government assistance, legislation and controls. Part 2 (Commodity Review) - covers industrial mineral commodities, from abrasives to zirconium. Part 3 (Mining Census) - tabulates statistics extracted from the mining census, together with some mineral processing statistics from the manufacturing census. Part 4 (Miscellaneous) - tabulates quantum and value data on mineral output provided by State departments of mines and their equivalents.

  6. Vitamin and Mineral Supplement Fact Sheets

    Science.gov (United States)

    ... website Submit Search NIH Office of Dietary Supplements Vitamin and Mineral Supplement Fact Sheets Search the list ... Supplements: Background Information Botanical Dietary Supplements: Background Information Vitamin and Mineral Fact Sheets Botanical Supplement Fact Sheets ...

  7. Studies of mineralization in South African rivers

    CSIR Research Space (South Africa)

    Hall, GC

    1978-03-01

    Full Text Available Several South African rivers are polluted by mineral salts of diffuse source. This pollution can be related to geological phenomena and to irrigation practices. Mineralization is problematic in that it can render surface waters unsuitable...

  8. Abundance estimation of spectrally similar minerals

    CSIR Research Space (South Africa)

    Debba, Pravesh

    2009-07-01

    Full Text Available This paper evaluates a spectral unmixing method for estimating the partial abundance of spectrally similar minerals in complex mixtures. The method requires formulation of a linear function of individual spectra of individual minerals. The first...

  9. Multifaceted role of clay minerals in pharmaceuticals

    OpenAIRE

    Khurana, Inderpreet Singh; Kaur, Satvinder; Kaur, Harpreet; Khurana, Rajneet Kaur

    2015-01-01

    The desirable physical and physiochemical properties of clay minerals have led them to play a substantial role in pharmaceutical formulations. Clay minerals like kaolin, smectite and palygorskite-sepiolite are among the world's most valuable industrial minerals and of considerable importance. The elemental features of clay minerals which caused them to be used in pharmaceutical formulations are high specific area, sorption capacity, favorable rheological properties, chemical inertness, swelli...

  10. Chitosan: collagen sponges. In vitro mineralization; Mineralizacao in vitro de esponjas de quitosana: colageno

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Virginia da C.A.; Silva, Gustavo M.; Plepis, Ana Maria G., E-mail: virginia@iqsc.usp.br [Instituto de Quimica de Sao Carlos- IQSC, Universidade de Sao Paulo, Sao Carlos, SP (Brazil)

    2011-07-01

    The regeneration of bone tissue is a problem that affects many people and scaffolds for bone tissue growth has been widely studied. The aim of this study was the in vitro mineralization of chitosan, chitosan:native collagen and chitosan:anionic collagen sponges. The sponges were obtained by lyophilization and mineralization was made by soaking the sponges in alternating solutions containing Ca{sup 2+} and PO{sub 4}{sup 3-}. The mineralization was confirmed by infrared spectroscopy, energy dispersive X-ray and X-ray diffraction observing the formation of phosphate salts, possibly a carbonated hydroxyapatite since Ca/P=1.80. The degree of mineralization was obtained by thermogravimetry calculating the amount of residue at 750 deg C. The chitosan:anionic collagen sponge showed the highest degree of mineralization probably due to the fact that anionic collagen provides additional sites for interaction with the inorganic phase. (author)

  11. Radiogenic cancer in underground miners

    International Nuclear Information System (INIS)

    Radford, E.P.

    1984-01-01

    Multiple studies have yielded remarkably consistent results relating radon daughter exposure to lung cancer risk in underground mining populations. The U.S. uranium miner study appears to be at variance with the other results. The primary reason is that the doses in the U.S. miner study were systematically overestimated, resulting in a risk coefficient that is lower than all the others. The significance of these findings for radiogenic lung cancer goes well beyond mining populations, because one is now aware of the implications of radon daughters detected in homes. The highest cumulative levels from radon exposures within homes have been found in Sweden, evidently because of their unusual geology with uranium-bearing ores near the surface. The Swedish authorities view this as a major public health problem that needs to be addressed

  12. Inhalation hazards to uranium miners

    International Nuclear Information System (INIS)

    Cross, F.T.

    1987-01-01

    Using both large and small experimental animals, this project is investigating levels of uranium-mine air contaminants that produce respiratory system disease in miners. Lung cancer incidence and deaths from degenerative lung disease are significantly elevated among uranium miners, but the cause-effect relationships for these diseases are based on inadequate epidemiological data. This project identifies agents or combinations of agents (both chemical and radiological), and their exposure levels, that produce respiratory tract lesions, including respiratory epithelial carcinoma, pneumoconiosis, and emphysema. Histopathological data for 100-working-level (WL) exposure rates show a significant increase in lung tumor risk over 1000-WL exposure rates for comparable cumulative radon-daughter exposures. Exposure of rats to radon daughters and other contaminants continues; the exposure of beagle dogs to uranium ore dust alone was terminated. Renal function and hematology data on ore-dust-exposed dogs are reported. 1 figure, 5 tables

  13. Inhalation hazards to uranium miners

    International Nuclear Information System (INIS)

    Cross, F.T.

    1983-01-01

    This project is investigating levels or uranium mine air contaminants, using both large and small experimental animals to model human respiratory system disease. Lung cancer and deaths by degenerative lung disease have reached epidemic proportions among uranium miners, but the cause-effect relationships for these diseases are based on inadequate epidemiological data. This project identifies agents or combinations of agents (both chemical and radiological), and their exposure levels, that produce respiratory tract lesions, including respiratory epithelial carcinoma, pneumoconiosis, and emphysema

  14. Inhalation hazards to uranium miners

    International Nuclear Information System (INIS)

    Cross, F.T.

    1982-01-01

    This project is investigating levels of uranium mine air contaminants, using both large and small experimental animals to model human respiratory system disease. Lung cancer and deaths by degenerative lung disease have reached epidemic proportions among uranium miners, but the cause-effect relationships for these diseases are based on inadequate epidemiological data. This project identifies agents or combinations of agents (both chemical and radiological) and their exposure levels that produce respiratory tract lesions, including respiratory epithelial carcinoma, pneumonconiosis and emphysema

  15. Cancer of lung in miners

    International Nuclear Information System (INIS)

    Kolenic, J.; Jurgova, T.; Volckova, A.; Zimacek, J.

    1995-01-01

    In the period of 1983-1994 was registered at Clinic of occupational diseases 87 cases of professional cancer of lung. Mostly /85/ of cases was related to miners, by whom act as risk factor alpha ionisation from radon. Average age group was 60.2 y, average time of exposition was 21.6 y. Epidermoid carcinoma was the most frequent type of tumor /46.5 %/ of cases/. Smoking plays a supportive role. (authors)

  16. Exogenic and endogenic Europa minerals

    Science.gov (United States)

    Maynard-Casely, H. E.; Brand, H. E. A.; Wilson, S. A.

    2016-12-01

    The Galileo Near Infrared Mapping Spectrometer (NIMS) identified a significant `non-ice' component upon the surface of Jupiter's moon Europa. Current explanations invoke both endogenic and exogenic origins for this material. It has long been suggested that magnesium and sodium sulfate minerals could have leached from the rock below a putative ocean (endogenic) 1 and that sulfuric acid hydrate minerals could have been radiologically produced from ionised sulfur originally from Io's volcanoes (exogenic) 2. However, a more recent theory proposes that the `non-ice' component could be radiation damaged NaCl leached from Europa's speculative ocean 3. What if the minerals are actually from combination of both endogenic and exogenic sources? To investigate this possibility we have focused on discovering new minerals that might form in the combination of the latter two cases, that is a mixture of leached sulfates hydrates with radiologically produced sulfuric acid. To this end we have explored a number of solutions in the MgSO4-H2SO4-H2O and Na2SO4-H2SO4-H2O systems, between 80 and 280 K with synchrotron x-ray powder diffraction. We report a number of new materials formed in this these ternary systems. This suggests that it should be considered that the `non-ice' component of the Europa's surface could be a material derived from endogenic and exogenic components. 1 Kargel, J. S. Brine volcanism and the interior structures of asteroids and icy satellites. Icarus 94, 368-390 (1991). 2 Carlson, R. W., Anderson, M. S., Mehlman, R. & Johnson, R. E. Distribution of hydrate on Europa: Further evidence for sulfuric acid hydrate. Icarus 177, 461-471, doi:10.1016/j.icarus.2005.03.026 (2005). 3 Hand, K. P. & Carlson, R. W. Europa's surface color suggests an ocean rich with sodium chloride. Geophysical Research Letters, 2015GL063559, doi:10.1002/2015gl063559 (2015).

  17. Minor sources of miner exposure

    International Nuclear Information System (INIS)

    Strong, J.C.; Green, N.; Brown, K.; O'Riordan, M.C.

    1983-01-01

    The sources of radiation exposure to miners in non-coal mines in addition to radon daughters are thoron daughters in mine air, long-lived radionuclides in mine dust and gamma radiation from the local rocks. A crude estimate of the total annual effective dose equivalent from these minor sources is 2 - 5 mSv which is of secondary importance compared to the dose from radon daughters. (UK)

  18. Epidemiological studies of Czech miners

    International Nuclear Information System (INIS)

    Tomasek, L.

    1995-01-01

    Lung cancer risk from radon was analysed in three cohorts of uranium (N=4320+5628) and burnt clay (N=915) miners. The follow-up of miners was extended up to 1990. Most of the cases (708) have been observed in the oldest (S) cohort followed since 1952. The other two cohorts, 18 years younger in average with substantially lower exposures, contributed 72 cases. Therefore, the main analyses of risk from radon were based on the S cohort. The data of the S cohort were subjected to checks both as for the individual exposures of the miners and the completeness of follow-up. The present mortality analyses from other causes suggest the follow-up is correct. The general patterns of mortality from violent deaths and diseases other than lung cancer show similar features in all the three cohorts, i.e. decreasing trend with time since first exposure in the first case, and increasing trend in the second one, confirming thus the healthy worker effect, in the first 20 years. A raised mortality was observed in later periods in respiratory and circulatory diseases and also in cancers other than lung cancer, suggesting that smoking habits among miners might be more frequent than in the general population. The estimates of lung cancer risk from radon exposure were based on relative linear models, where cumulative exposures were lagged by 5 years. The linear effect of cumulative exposure was substantially modified by time since exposure, exposure rate, and age at exposure. From the estimated intercept, it can be deduced that in the absence of exposure to radon, the estimated mortality from lung cancer in the cohort is about 1.5 times higher than in the general population. (orig.) [de

  19. 36 CFR 331.17 - Minerals.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Minerals. 331.17 Section 331..., KENTUCKY AND INDIANA § 331.17 Minerals. All activities in connection with prospecting, exploration, development, mining or other removal or the processing of mineral resources and all uses reasonably incident...

  20. Contribution of the Minerals Industry towards Sustainable ...

    African Journals Online (AJOL)

    South Africa is a leading producer of a number of mineral commodities, and the minerals industry is a key driver of the South African economy. Ensuring that this mineral wealth is exploited in a manner consistent with the principles of sustainable development requires policies and strategies that are underpinned by a ...

  1. Recovery of asphalt from bituminous minerals

    Energy Technology Data Exchange (ETDEWEB)

    Jossinet, J

    1881-12-31

    A process is disclosed for the recovery of asphalt from bituminous minerals, consisting in that the mineral is extracted with mineral oil, which is recovered by distilling the raw asphalt and distilling the solution to obtain on the one hand the liquid oil contained in the raw asphalt for use in the extraction and on the other hand distilled asphalt.

  2. Sustainability in the UK construction minerals industry

    OpenAIRE

    Mitchell, Clive

    2015-01-01

    Sustainability in the UK construction minerals industry Clive Mitchell, Industrial Minerals Specialist, British Geological Survey, Nottingham, UK Email: Sustainability is not just about environmental protection it also concerns biodiversity, community relations, competence, employment, geodiversity, health and safety, resource efficiency, restoration and stakeholder accountability. The UK construction minerals industry aims to supply essential materials in a sustainabl...

  3. Chemical dissolution of sulfide minerals

    Science.gov (United States)

    Chao, T.T.; Sanzolone, R.F.

    1977-01-01

    Chemical dissolution treatments involving the use of aqua regia, 4 N HNO3, H2O2-ascorbic acid, oxalic acid, KClO3+HCl, and KClO3+HCl followed by 4 N HNO3 were applied to specimens of nine common sulfide minerals (galena, chalcopyrite, cinnabar, molybdenite, orpiment, pyrite, stibnite, sphalerite, and tetrahedrite) mixed individually with a clay loam soil. The resultant decrease in the total sulfur content of the mixture, as determined by using the Leco induction furnace, was used to evaluate the effectiveness of each chemical treatment. A combination of KClO3+HCl followed by 4 N HNO3 boiling gently for 20 min has been shown to be very effective in dissolving all the sulfide minerals. This treatment is recommended to dissolve metals residing in sulfide minerals admixed with secondary weathering products, as one step in a fractionation scheme whereby metals in soluble and adsorbed forms, and those associated with organic materials and secondary oxides, are first removed by other chemical extractants.

  4. Lead isotope in mineral exploration

    International Nuclear Information System (INIS)

    Gulson, B.L.

    1986-01-01

    This book provides an up-to-date state-of-the-art review of lead isotopes in mineral exploration. Beginning with an historical review on suggested uses of lead isotopes in mineral exploration, the author then outlines the theoretical aspects of lead isotopes and illustrates that the method is based on well-known principles of radioactive decay, from which isotopic signatures for different styles of mineralization are derived. The varying isotopic signatures are then introduced. The major part of the book details over 40 case histories for base and precious metals, uranium and tin using sampling media such as sulfides, gossans, soils, weathered bedrock, vegetation and groundwaters. Advantages and disadvantages of each are discussed. Examples are given of the use of lead isotopes in testing conceptual models for exploration. The success rate and cost-effectiveness of the method are illustrated by actual exploration examples. Analytical advances which should lower the cost of the method and future uses are outlined. Many of the case histories use recently published or unpublished data, 27 tables of which are given in an appendix. Details of sampling, the methods for obtaining the isotope ratios, and a commercially-available integrated lead isotope service are also provided. (Auth.)

  5. High-strength mineralized collagen artificial bone

    Science.gov (United States)

    Qiu, Zhi-Ye; Tao, Chun-Sheng; Cui, Helen; Wang, Chang-Ming; Cui, Fu-Zhai

    2014-03-01

    Mineralized collagen (MC) is a biomimetic material that mimics natural bone matrix in terms of both chemical composition and microstructure. The biomimetic MC possesses good biocompatibility and osteogenic activity, and is capable of guiding bone regeneration as being used for bone defect repair. However, mechanical strength of existing MC artificial bone is too low to provide effective support at human load-bearing sites, so it can only be used for the repair at non-load-bearing sites, such as bone defect filling, bone graft augmentation, and so on. In the present study, a high strength MC artificial bone material was developed by using collagen as the template for the biomimetic mineralization of the calcium phosphate, and then followed by a cold compression molding process with a certain pressure. The appearance and density of the dense MC were similar to those of natural cortical bone, and the phase composition was in conformity with that of animal's cortical bone demonstrated by XRD. Mechanical properties were tested and results showed that the compressive strength was comparable to human cortical bone, while the compressive modulus was as low as human cancellous bone. Such high strength was able to provide effective mechanical support for bone defect repair at human load-bearing sites, and the low compressive modulus can help avoid stress shielding in the application of bone regeneration. Both in vitro cell experiments and in vivo implantation assay demonstrated good biocompatibility of the material, and in vivo stability evaluation indicated that this high-strength MC artificial bone could provide long-term effective mechanical support at human load-bearing sites.

  6. Water in Nominally Anhydrous Minerals from Nakhlites and Shergottites

    Science.gov (United States)

    Peslier, Anne H.

    2013-01-01

    Estimating the amount of water in the interior of terrestrial planets has tremendous implications on our understanding of solar nebula evolution, planet formation and geological history, and extraterrestrial volcanism. Mars has been a recent focus of such enquiry with complementary datasets from spacecrafts, rovers and martian meteorite studies. In planetary interiors, water can be dissolved in fluids or melts and hydrous phases, but can also be locked as protons attached to structural oxygen in lattice defects in nominally anhydrous minerals (NAM) such as olivine, pyroxene, or feldspar [1-3]. Measuring water in Martian meteorite NAM is challenging because the minerals are fragile and riddled with fractures from impact processes that makes them break apart during sample processing. Moreover, curing the sample in epoxy causes problems for the two main water analysis techniques, Fourier transform infrared spectrometry (FTIR) and secondary ionization mass spectrometry (SIMS). Measurements to date have resulted in a heated debate on how much water the mantle of Mars contains. SIMS studies of NAM [4], amphiboles [5], and apatites [6-8] from Martian meteorites report finding enough water in these phases to infer that the martian mantle is as hydrous as that of the Earth. On the other hand, a SIMS study of glass in olivine melt inclusions from shergottites concludes that the Martian mantle is much drier [9]. The latter interpretation is also supported by the fact that most martian hydrous minerals generally have the relevant sites filled with Cl and F instead of H [10,11]. As for experimental results, martian basalt compositions can be reproduced using water as well as Cl in the parent melts [12,13]. Here FTIR is used to measure water in martian meteorite minerals in order to constrain the origin of the distribution of water in martian meteorite phases.

  7. Mortality among sulfide ore miners

    International Nuclear Information System (INIS)

    Ahlman, K.; Koskela, R.S.; Kuikka, P.; Koponen, M.; Annanmaeki, M.

    1991-01-01

    Lung cancer mortality was studied during 1965-1985 in Outokumpu township in North Karelia, where an old copper mine was located. Age-specific lung cancer death rates (1968-1985) were higher among the male population of Outokumpu than among the North Karelian male population of the same age excluding the Outokumpu district (p less than .01). Of all 106 persons who died from lung cancer during 1965-1985 in Outokumpu township, 47 were miners of the old mine, 39 of whom had worked there for at least three years and been heavily exposed to radon daughters and silica dust. The study cohort consisted of 597 miners first employed between 1954 and 1973 by a new copper mine and a zinc mine, and employed there for at least 3 years. The period of follow-up was 1954-1986. The number of person-years was 14,782. The total number of deaths was 102; the expected number was 72.8 based on the general male population and 97.8 based on the mortality of the male population of North Karelia. The excess mortality among miners was due mainly to ischemic heart disease (IHD); 44 were observed, the expected number was 22.1, based on the general male population, and the North Karelian expected number was 31.2 (p less than .05). Of the 44 miners who died from IHD, 20 were drillers or chargers exposed to nitroglycerin in dynamite charges, but also to several simultaneous stress factors including PAHs, noise, vibration, heavy work, accident risk, and working alone. Altogether 16 tumors were observed in the cohort. Ten of these were lung cancers, the expected number being 4.3. Miners who had died from lung cancer were 35-64 years old, and had entered mining work between 1954 and 1960. Five of the ten lung cancer cases came from the zinc mine (1.7 expected). Three of them were conductors of diesel-powered ore trains

  8. 25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Other minerals and deep-lying lead and zinc minerals. 215.25 Section 215.25 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead...

  9. Impact of environmental chemistry on mycogenic Mn oxide minerals

    Science.gov (United States)

    Santelli, C. M.; Farfan, G. A.; Post, A.; Post, J. E.

    2012-12-01

    Manganese (Mn) oxide minerals are ubiquitous in aquatic and terrestrial environments and their presence can have broad environmental consequences. In particular, Mn oxides scavenge nutrients and metals, degrade complex organics, and oxidize a variety of inorganic contaminants. The "reactivity" of Mn oxides, however, is highly dependent upon crystallite size, composition, and structure, which are largely determined by environmental factors such as solution chemistry. It is has been suggested that most Mn oxides in terrestrial and aquatic environments are formed by microbial activity; indeed, a diversity of Mn(II)-oxidizing bacteria and fungi have been isolated and their mineral byproducts are consistent with those observed in natural systems. Previous studies showed that Mn(II)-oxidizing Ascomycete fungi produce highly-disordered, nanocrystalline Mn oxides that are structurally similar to synthetic δ-MnO2 or natural vernadite. Unlike related studies with Mn-oxidizing bacteria, Mn oxides produced by these fungi did not "age" or transform to more crystalline mineral phases with time. We hypothesize that fungal growth conditions, in particular the low concentration of cations, are inhibiting secondary mineral formation. The overall goal of this research is to examine the structure and speciation of fungally-precipitated Mn oxides with respect to fungal species, time, and concentration of soluble Mn(II), Na, and Ca - three environmentally relevant cations that promote the transformation of δ-MnO2 to more crystalline mineral phases such as feitknechtite, birnessite, or ranciéite. For this study, we examined the Mn oxides formed by different species of Mn(II)-oxidizing fungi (Pyrenochaeta sp., Stagonospora sp., Plectosphaerella cucumerina., and Acremonium strictum). Isolates were grown for 8 or 16 days in a nutrient lean media consisting of yeast extract, trace elements and 0.2 mM MnCl2 supplemented with varying concentrations of Na, Ca, or Mn(II) compounds. The

  10. Nuclear technology and mineral recovery

    International Nuclear Information System (INIS)

    Stewart, Richard M.; Niermeyer, Karl E.

    1970-01-01

    The particular aspect of nuclear technology most applicable to the mineral field, as has been pointed out by various authors, is nuclear blasting. The prime target for this nuclear blasting has usually been a large disseminated deposit of copper mineralization which, because of large dimensions, employs the nuclear devices most effectively. From the work of the AEC we know that the larger nuclear devices fragment rock for a lower energy cost per unit of ground broken than do smaller nuclear devices or chemical explosives. A mineralized deposit near the surface is usually not amenable to nuclear fragmentation, nor are the more deeply buried thin deposits. Also, one would not anticipate fragmenting a zone of excessively erratic mineralization with nuclear devices. Many of our mineralized areas would be eliminated using the above criteria, so at this point you are well aware that my self-imposed limitation is to nuclear blasting and large disseminated copper deposits. As with most other industries, copper mining faces rising costs and greater demands for its products. One of the rising cost features peculiar to extractive industries is the reliance placed on production from lower grade deposits as the higher grade deposits are depleted. As the grade or metal content of an orebody decreases more material must be handled to produce a given amount of metal. The increased volume of ore which must be handled as the grade declines requires expansion of facilities and higher capital expenditures. Expansion of facilities for mining, milling, and concentrating of the ore increases the per unit capital cost of the end product--copper. Increased copper consumption will aggravate this situation with demand for more metal, much of which will have to be obtained from lower grade deposits. As the higher grade deposits are depleted, future production will come from those deposits which cannot be exploited economically today. Most familiar of the proposed new methods for copper mining

  11. Nuclear technology and mineral recovery

    Energy Technology Data Exchange (ETDEWEB)

    Stewart, Richard M; Niermeyer, Karl E [Anaconda Company, Salt Lake City, UT (United States)

    1970-05-15

    The particular aspect of nuclear technology most applicable to the mineral field, as has been pointed out by various authors, is nuclear blasting. The prime target for this nuclear blasting has usually been a large disseminated deposit of copper mineralization which, because of large dimensions, employs the nuclear devices most effectively. From the work of the AEC we know that the larger nuclear devices fragment rock for a lower energy cost per unit of ground broken than do smaller nuclear devices or chemical explosives. A mineralized deposit near the surface is usually not amenable to nuclear fragmentation, nor are the more deeply buried thin deposits. Also, one would not anticipate fragmenting a zone of excessively erratic mineralization with nuclear devices. Many of our mineralized areas would be eliminated using the above criteria, so at this point you are well aware that my self-imposed limitation is to nuclear blasting and large disseminated copper deposits. As with most other industries, copper mining faces rising costs and greater demands for its products. One of the rising cost features peculiar to extractive industries is the reliance placed on production from lower grade deposits as the higher grade deposits are depleted. As the grade or metal content of an orebody decreases more material must be handled to produce a given amount of metal. The increased volume of ore which must be handled as the grade declines requires expansion of facilities and higher capital expenditures. Expansion of facilities for mining, milling, and concentrating of the ore increases the per unit capital cost of the end product--copper. Increased copper consumption will aggravate this situation with demand for more metal, much of which will have to be obtained from lower grade deposits. As the higher grade deposits are depleted, future production will come from those deposits which cannot be exploited economically today. Most familiar of the proposed new methods for copper mining

  12. Geological structure and prospects of noble metal ore mineralization of the Khayrkhan gabbroid massif (Western Mongolia)

    Science.gov (United States)

    Kurumshieva, K. R.; Gertner, I. F.; Tishin, P. A.

    2017-12-01

    An analysis of the distribution of noble metals in zones of sulfide mineralization makes it possible to justify the isolation of four ore-bearing horizons with a specific geochemical zonation. A rise in the gold content relative to palladium and platinum is observed from the bottom upwards along the section of the stratified series of gabbroids. The study of the mineral phases of sulphides and the noble minerals itself indicates the evolution of hydrothermal solutions, which determines the different activity and mobility of the fluid (mercury, tellurium, sulfur) and ore (copper, nickel, iron, platinum, gold and silver) components.

  13. Choosing mineral carrier of nanoscale additives for asphalt concrete

    Directory of Open Access Journals (Sweden)

    Inozemtsev Sergey Sergeevich

    2014-03-01

    Full Text Available At present time the operation life of the majority of roads is essentially shorter than required. The reason for it is the increase in traffic intensity and axle loads of automobile transport. The obvious reasons for early wear of roads are the low quality of the components used and low industrial standards while producing asphalt pavement. In this paper the mineral material was selected as a carrier of nanoscale additives for asphalt. The optimal modes for grinding mineral materials were identified, which provide correspondence of their structure parameters with the developed model. The influence of different mineral nanomodifier carriers on the structure formation processes was estimated. It is shown that among a number of mineral materials diatomite has high activity in relation to the bitumen, because it has a highly porous structure. It is also shown that as a result of lighter fractions of bitumen adsorption on the border of phase interface, diatomite and bitumen changes from the free state to the film, and solvate shell of bitumen is saturated with asphaltenes. With the help of IR spectroscopy the authors defined the nature of the diatomite and bitumen interaction and proved that in the process of their interaction there occurs physical adsorption with additional absorption of bitumen components into the pore space of diatomite grains.

  14. Mineralogical characterization of beach sand minerals: traditional and modern approaches

    International Nuclear Information System (INIS)

    Krishnamurthy, P.

    2016-01-01

    Precise identification of beach sand minerals is an essential prerequisite for the reserve estimation of a given deposit and also in the subsequent evaluation of the process flow sheet for its optimal recovery. Traditional methods that are used for the identification of the beach sand minerals such as magnetite, hematite, ilmenite, rutile, anatase, zircon, garnet, sillimanite, monazite, quartz and others include heavy liquid separation (bromoform and methylene iodide) and studying the optical properties of the grains from different fractions so as to identify the specific phases in a sample. Grain counting of specific minerals from a given sievefraction under a petrological microscope to estimate the mode and their subsequent conversion in to weight percent fractions forms the critical second stage that is followed by the reserve estimates. These methodologies are tedious and time consuming often involving a few days for a single sample. The paper introduces the numerous instrumental methods (XRF, XRD - Rietveld and CCSEM) of mineral speciation and their qualification in with case studies from the west coast deposits in India

  15. Perencanaan Strategik SBU Mineral PT Sucofindo (Persero

    Directory of Open Access Journals (Sweden)

    Suprapto Suprapto

    2017-05-01

    Full Text Available Strategic planning requires an organization in the face of today's business competition and a more complex future. Likewise, Mineral Gas Station also requires this strategic planning as a newly formed business unit of 2015. Therefore, the company analyzed its internal and external factors as well as a future review of the mineral service industry to stay afloat, grow and develop. The objectives of this study were to identify the internal performance and core competencies of Mineral Gas Station, to identify the external macro environment condition and external micro intensity of mineral service industry competition, to map the current position of the company, to recommend appropriate business strategy in facing competition pressure, and to develop the objectives and program of the company. This research used descriptive and quantitative analysis methods with a purposive sampling technique. The results show that the position of Mineral Gas Station on the intensity of mineral service competition is 'moderate' and is in quadrant of 'grow and build'. Therefore, the appropriate strategy is intensive strategy (market penetration, market development and product development. Mineral Gas Station require to conduct customer satisfaction surveys related to customer perspectives which becomes the most important strategic factor with a focus on customer complaint factor. Further research is needed by involving all external parties so that the results will be more independent.Keywords: mineral services, strategic planning, competition, mineral gas station, SucofindoABSTRAKPerencanaan strategik dibutuhkan organisasi dalam menghadapi persaingan bisnis saat ini dan masa depan yang semakin komplek. Demikian juga yang dibutuhkan SBU Mineral sebagai unit bisnis yang baru terbentuk 2015, dengan menganalisis faktor internal dan ekternal perusahaan serta tinjauan masa depan industri jasa mineral untuk tetap bertahan, tumbuh dan berkembang. Tujuan penelitian ini adalah

  16. Mineral resource of the month: vermiculite

    Science.gov (United States)

    Tanner, Arnold O.

    2014-01-01

    Vermiculite comprises a group of hydrated, laminar magnesium-aluminum-iron silicate minerals resembling mica. They are secondary minerals, typically altered biotite, iron-rich phlogopite or other micas or clay-like minerals that are themselves sometimes alteration products of amphibole, chlorite, olivine and pyroxene. Vermiculite deposits are associated with volcanic ultramafic rocks rich in magnesium silicate minerals, and flakes of the mineral range in color from black to shades of brown and yellow. The crystal structure of vermiculite contains water molecules, a property that is critical to its processing for common uses.

  17. Australian mineral industry annual review for 1984

    Energy Technology Data Exchange (ETDEWEB)

    1987-01-01

    This volume of the Australian Mineral Industry Annual Review records development and performance of the Australian mineral industry during the calendar year 1984. It reports production, consumption, treatment, trade, prices, new developments, exploration, and resources for mineral commodities including fuels, and summarises equivalent developments abroad. Part 1. 'general review' after briefly surveying the world mineral industry, summarises developments in the Australian mineral industry as a whole, under the headings: the industry in the national economy, prices, exploration expenditure, investment, income tax, royalties, structural data, wages and salaries, industrial disputes, and government assistance, legislation, and controls. Part 2. 'commodity review' covers individual mineral commodity groups, from abrasives to zirconium. Part 3, 'mining census', tabulates statistics extracted from the mining census, together with some mineral processing statistics from the manufacturing census. Part 4 tabulates quantity and value data on mineral output provided by state departments of mines and their equivalents. Listed in appendices are: principal mineral producers; ore buyers and mineral dealers; government mining services; analytical laboratories; state mines departments and equivalents; industry, professional and development organisations and associations, etc; summary of mineral royalties payable in the states and territories; and summary of income tax provisions and federal government levies.

  18. AN INVESTIGATION OF THE MINERAL IN DUCTILE AND BRITTLE CORTICAL MOUSE BONE

    Science.gov (United States)

    Rodriguez-Florez, Naiara; Garcia-Tunon, Esther; Mukadam, Quresh; Saiz, Eduardo; Oldknow, Karla J.; Farquharson, Colin; Millán, José Luis; Boyde, Alan; Shefelbine, Sandra J.

    2015-01-01

    Bone is a strong and tough material composed of apatite mineral, organic matter and water. Changes in composition and organization of these building blocks affect bone’s mechanical integrity. Skeletal disorders often affect bone’s mineral phase, either by variations in the collagen or directly altering mineralization. The aim of the current study was to explore the differences in the mineral of brittle and ductile cortical bone at the mineral (nm) and tissue (µm) levels using two mouse phenotypes. Osteogenesis imperfecta murine (oim−/−) mice were used to model brittle bone; PHOSPHO1 mutants (Phospho1−/−) had ductile bone. They were compared to their respective wild-type controls. Femora were defatted and ground to powder to measure average mineral crystal size using X-ray diffraction (XRD), and to monitor the bulk mineral to matrix ratio via thermogravimetric analysis (TGA). XRD scans were run after TGA for phase identification, to assess the fractions of hydroxyapatite and β-tricalcium phosphate. Tibiae were embedded to measure elastic properties with nanoindentation and the extent of mineralization with backscattered electron microscopy (qbSEM). Interestingly, the mineral of brittle oim−/− and ductile Phospho1−/− bones had many similar characteristics. Both pathology models had smaller apatite crystals, lower mineral to matrix ratio, and showed more thermal conversion to β-tricalcium phosphate than their wild-types, indicating deviations from stoichiometric hydroxyapatite in the original mineral. The degree of mineralization of the bone matrix was different for each strain: oim−/− were hypermineralized, while Phospho1−/− were hypomineralized. However, alterations in the mineral were associated with reduced tissue elastic moduli in both pathologies. Results revealed that despite having extremely different whole bone mechanics, the mineral of oim−/− and Phospho1−/− has several similar trends at smaller length scales. This

  19. Australian mineral industry annual review for 1986

    Energy Technology Data Exchange (ETDEWEB)

    1988-01-01

    This volume of the Australian Mineral Industry Annual Review records the development and performance of the industry during the calendar year 1986. It reports production, consumption, treatment, trade, prices, new developments, exploration, and resources for mineral commodities including fuels, and summarises equivalent developments abroad. Part 1, 'General Review', after briefly surveying the world mineral industry, summarises developments in the Australian mineral industry as a whole. Part 2, 'Commodity Review', covers individual mineral commodities and commodity groups including brown coal, black coal and peat. Part 3, 'Mining Census', tabulates statistics extracted from the Mining Census, together with some mineral processing statistics from the Manufacturing Census. Part 4, tabulates quantity and value data on mineral output provided by the State departments of mines and their equivalents. The commodity review of black coal has been abstracted separately.

  20. The radioactivity of bottled mineral waters

    International Nuclear Information System (INIS)

    Vrakova, M.; Babarikova, F.; Belanova, A.

    2005-01-01

    Mineral waters with increased contents of minerals (total mineralization ranging from 1000 to 4000 mg.dm -3 ) can also contain increased concentrations of natural radionuclides. For this reason it is necessary to monitor radioactivity of mineral and thermal springs. Hundreds of springs which are used for drinking purposes are spread in many regions all over Slovakia. In our laboratory we determined these radionuclides in mineral waters: total alpha, total beta, volume activity 222 Rn, concentration of U nat , volume 226 Ra, 228 Ra and 210 Po. From values of determined volume activities of radionuclides we calculated total effective dose from reception mineral waters. By calculation of effective dose we supposed consumption of mineral water 150 dm 3 .year -1 (0.4 dm 3 .day -1 ) for adults (according to UNSCEAR). Conversion factors are initiated in the regulation of Ministry of Health of Slovak Republic (MZ SR No.12/2001). (authors)

  1. Mineralization of Carbon Dioxide: Literature Review

    Energy Technology Data Exchange (ETDEWEB)

    Romanov, V; Soong, Y; Carney, C; Rush, G; Nielsen, B; O' Connor, W

    2015-01-01

    CCS research has been focused on CO2 storage in geologic formations, with many potential risks. An alternative to conventional geologic storage is carbon mineralization, where CO2 is reacted with metal cations to form carbonate minerals. Mineralization methods can be broadly divided into two categories: in situ and ex situ. In situ mineralization, or mineral trapping, is a component of underground geologic sequestration, in which a portion of the injected CO2 reacts with alkaline rock present in the target formation to form solid carbonate species. In ex situ mineralization, the carbonation reaction occurs above ground, within a separate reactor or industrial process. This literature review is meant to provide an update on the current status of research on CO2 mineralization. 2

  2. Identification of a new mineralized tissue in the notochord of reared Siberian sturgeon (Acipenser baerii).

    Science.gov (United States)

    Leprévost, Amandine; Azaïs, Thierry; Trichet, Michael; Sire, Jean-Yves

    2017-11-01

    In a study aiming to improve knowledge on the mineralization of the axial skeleton in reared Siberian sturgeon (Acipenser baerii Brandt, 1869), we discovered a new mineralized tissue within the notochord. To our knowledge, such a structure has never been reported in any vertebrate species with the exception of the pathological mineralization of the notochord remains in degenerative intervertebral disks of mammals. Here, we describe this enigmatic tissue using X-ray microtomography, histological analyses and solid state NMR-spectroscopy. We also performed a 1-year monitoring of the mineral content (MC) of the notochord in relation with seasonal variations of temperature. In all specimens studied from 2-year-old juveniles onwards, this mineralized structure was found within a particular region of the notochord called funiculus. This feature first appears in the abdominal region then extends posteriorly with ageing, while the notochord MC also increases. The mineral phase is mainly composed of amorphous calcium phosphate, a small amount of which changes into hydroxyapatite with ageing. The putative role of this structure is discussed as either a store of minerals available for the phosphocalcic metabolism, or a mechanical support in a species with a poorly mineralized axial skeleton. A pathological feature putatively related to rearing conditions is also discussed. © 2017 Wiley Periodicals, Inc.

  3. Bone mineral content measurement by bone mineral analyzer

    International Nuclear Information System (INIS)

    Yamamoto, Itsuo; Dokoh, Shigeharu; Fukunaga, Masao; Torizuka, Kanji; Kosaka, Tadako.

    1976-01-01

    With a bone mineral analyzer (Studsvik Bone Scanner 7102), bone mineral content (BMC) was validated using various concentrations of standard CaCO 3 . Seventy-five normal subjects, nineteen patients with rheumathoid arthritis (RA) and twenty-two patients with abnormal thyroid function were investigated by this method. Some inherent problems concerning the present measurements were also discussed. Reproducibility of BMC in sixteen normal subjects during a four months interval was +-4% on the mid-shaft of the radius and +-5% on the distal head of the radius, respectively. Although correlation of the single energy method and the dual energy method with the bone scanner was high (r=0.970), the single energy method was probably underestimated due to the fat layer. BMC in normal subjects was highest in 30th and 40th decades for both males and females, and gradually decreased with aging. Males had higher BMC and BMC/bone width than did females. All of the stage 1 group of RA patients, according to roentgenographic staging, revealed normal BMC, but most of stage 2 and 3 groups had abnormally low BMC, suggesting that progression of the disease may be an important factor in BMC values. The BMC of hyperthyroid patients was low, whereas that of euthyroid patients was normal. Serial measurements of BMC in a hyperparathyroid patient and a hyperthyroid patient revealed distinct recurrence of BMC after treatment. (Evans, J.)

  4. Daily mineral intakes for Japanese

    International Nuclear Information System (INIS)

    Shiraishi, Kunio

    1990-01-01

    Recently it became necessary to assess the dietary intake of both stable and radioactive elements for non-radiation workers. But data of mineral intake in the literature are not good enough for this assessment. ICRP Pub. 23 in 'Reference Man' is one of the best references in this field. ICRP Reference Man was selected as the standard for Caucasian by using values reported during early 1970s or before. Moreover it seems not to be suitable for Japanese (Mongolian). In this report, analytical methods of minerals in total diet samples for Japanese were described. Furthermore, daily intakes for Japanese (Reference Japanese Man) and ICRP Reference Man were compared. After collected by a duplicate portion study and a model diet study, diet samples were dry-ashed followed by wet-digestion with a mixture of HNO 3 and HClO 4 . Diet sample solutions thus prepared were analysed by using atomic absorption spectrometry (AAS), inductively-coupled plasma atomic-emission spectrometry (ICP-AES), and inductively-coupled plasma mass spectrometry (ICP-MS). Matrix effects of major elements (Na, K, P, Ca and Mg) in diet samples were compensated by a matrix-matching method. About 20 elements were simultaneously determined by ICP-AES and ICP-MS, more easily than by AAS. Most of dietary mineral intakes, except for Na, Mn, and Sr, for Japanese were lower than those of ICRP Reference Man. But, dietary intakes were found to be different depending on countries, even among European and American countries. New representative data for as many elements as possible are necessary now. (author)

  5. On the interfacial interaction between bituminous binders and mineral surfaces as present in asphalt mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, Hartmut R., E-mail: hartmut.fischer@tno.nl [TNO Technical Sciences, De Rondom 1, 5612 AP Eindhoven (Netherlands); Dillingh, E.C.; Hermse, C.G.M. [TNO Technical Sciences, De Rondom 1, 5612 AP Eindhoven (Netherlands)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer Direct measurement of the contact angle between different phases of the microstructure of bitumen and aggregate surfaces of different chemical nature using AFM. Black-Right-Pointing-Pointer Common schema of adhesion of bitumen on aggregates via asphaltene precipitation. Black-Right-Pointing-Pointer Surface roughness/porosity more important than chemical nature for strength of adhesion between aggregate and bitumen. - Abstract: The interfacial interaction between bituminous binders and several mineral surfaces of different chemical nature as present in asphalt mixtures has been investigated using atomic force microscopy. Several dry mineral surfaces display comparable wetting with respect to the different phases present in the micro-structure of bitumen, regardless of differences in their chemical nature. The peri/catana-phase shows a preferential wetting due to adsorption of asphaltene aggregates to the mineral surfaces.

  6. On the interfacial interaction between bituminous binders and mineral surfaces as present in asphalt mixtures

    International Nuclear Information System (INIS)

    Fischer, Hartmut R.; Dillingh, E.C.; Hermse, C.G.M.

    2013-01-01

    Highlights: ► Direct measurement of the contact angle between different phases of the microstructure of bitumen and aggregate surfaces of different chemical nature using AFM. ► Common schema of adhesion of bitumen on aggregates via asphaltene precipitation. ► Surface roughness/porosity more important than chemical nature for strength of adhesion between aggregate and bitumen. - Abstract: The interfacial interaction between bituminous binders and several mineral surfaces of different chemical nature as present in asphalt mixtures has been investigated using atomic force microscopy. Several dry mineral surfaces display comparable wetting with respect to the different phases present in the micro-structure of bitumen, regardless of differences in their chemical nature. The peri/catana-phase shows a preferential wetting due to adsorption of asphaltene aggregates to the mineral surfaces.

  7. Leptin and bone mineral density

    DEFF Research Database (Denmark)

    Morberg, Cathrine M.; Tetens, Inge; Black, Eva

    2003-01-01

    Leptin has been suggested to decrease bone mineral density (BMD). This observational analysis explored the relationship between serum leptin and BMD in 327 nonobese men (controls) (body mass index 26.1 +/- 3.7 kg/m(2), age 49.9 +/- 6.0 yr) and 285 juvenile obese men (body mass index 35.9 +/- 5.9 kg...... males, but it also stresses the fact that the strong covariation between the examined variables is a shortcoming of the cross-sectional design....

  8. Strata control in mineral engineering

    International Nuclear Information System (INIS)

    Bieniawski, Z.T.

    1986-01-01

    This book covers the state-of-the-art of strata control practice both in the United States and abroad with respect to strata reinforcement by rock bolting, long wall mining technology and innovations in energy development, such as mining for oil and tunneling for storage of high-level nuclear waste in deep underground repositories. It features coverage of design concepts in rock engineering and rockbolt systems, stability of rock pillars, rockbursts, shaft design and construction and a detailed consideration of mineral and energy needs in the United States

  9. Reducing the extraction of minerals

    DEFF Research Database (Denmark)

    Bouzon, Marina; Govindan, Kannan; Rodriguez, Carlos Manuel Taboada

    2015-01-01

    Mass consumption and shortening product lifecycles have increased worldwide production. Consequently, more raw materials such as minerals are used, and available landfills are filling up. Companies are urged to effectively incorporate sustainability issues such as End-of-life (EOL) management...... and Reverse Logistics (RL) practices to close the loop and diminish the amount of raw materials used in their production systems. However, implementing RL implies dealing with its barriers. The purpose of this article is to focus on the recovery of EOL products that use mostly raw materials from the mining...

  10. ROCKS & MINERALS DETERMINATION AND ANALYSIS

    Institute of Scientific and Technical Information of China (English)

    2015-01-01

    20150204 Abaydulla Alimjan(Department of Chemistry and Environmental Sciences,Kashgar Teachers College,Kashgar 844006,China);Cheng Chunying Non-Metallic Element Composition Analysis of Non-Ferrous Metal Ores from Oytagh Town,Xinjiang(Rock and Mineral Analysis,ISSN0254-5357,CN11-2131/TD,33(1),2014,p.44-50,5illus.,4tables,28refs.)Key words:nonferrous metals ore,nonmetals,chemical analysis,thermogravimetric analysis Anions in non-ferrous ore materials

  11. 30 CFR 250.918 - What are the CVA's primary duties during the installation phase?

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What are the CVA's primary duties during the installation phase? 250.918 Section 250.918 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE... appropriate (i) Loadout and initial flotation operations; (ii) Towing operations to the specified location...

  12. Petrography, alteration and genesis of iron mineralization in Roshtkhar

    Directory of Open Access Journals (Sweden)

    Habib Biabangard

    2017-07-01

    pyrite and chalcopyrite. Both of these two types were affected by supergene processes and iron hydroxides (goethite and limonite and Cu carbonates (malachite and azurite were formed as a result. The gangue minerals are mainly calcite, quartz and clay minerals. The common textures of the hypogene mineralization are mainly open space filling that are characterized by crustification, layered, geode and vug infill, cockade and comb structures. The supergene mineralization is characterized by both open space filling and replacement textures. Based on ore microscopic studies, the iron oxide minerals of hematite and magnetite were mainly formed earlier than the sulfide minerals of chalcopyrite and pyrite. The hypogene vein deposits such as those of the city of Roshtkhar are mainly formed by hydrothermal fluids. The ore minerals in the veins and breccias are deposited as a result of simple cooling, depressurization, fluid mixing, boiling and chemical barriers. The Fe and Cu mineralization in Roshtkhar is genetically related to the hydrothermal fluids that were derived from the magma during emplacement of the intrusive rocks. It seems that the spicularitic hematite is a hypogene early phase indicating the oxygen fugacity of formation environment was high. In the lower fO2, magnetite was replaced by hematite and chalcopyrite and pyrite were probably deposited from hydrothermal fluids as a result of a decrease in fO2, temperature or pH and increase of fS2. The Cu carbonates, secondary sulfides and iron hydroxides were formed by oxidation of the primary sulfides and iron oxides in supergene stage. References Grant, J.A. 2005. Isocon analysis: A brief review of the method and applications. Physics and Chemistry of the Earth, 30(50: 997-1004. Hitzman, M.M., Orekes, N. and Einaudi, M.T. 1992. Geological characteristics and tectonic setting of Proterozoic iron oxide (Cu-Au-LEE deposits. Precambrian Research, 58(8: 241-287. Karimpour, M.H. and Malekzadeh Shafaroudi, A. 2007. Geochemistry

  13. An improved method for the immunological detection of mineral bound protein using hydrofluoric acid and direct capture.

    Science.gov (United States)

    Craig, O E; Collins, M J

    2000-03-06

    Immunological detection of proteins adsorbed to mineral and ceramic surfaces has proved not only difficult but controversial. Unlike the immunological detection of proteins associated with carbonate or phosphate minerals (e.g. shells and bones) proteins adsorbed to siliceous minerals cannot readily be removed by dissolution of the mineral phase. We have previously examined alternative extraction methodologies which claim to bring the protein into solution, but found none of these to be effective. Here we report a novel strategy for immuno-detection of proteins adsorbed to siliceous minerals, the Digestion and Capture Immunoassay (DACIA). The method involves the use of cold, concentrated (4M) hydrofluoric acid (HF) with the simultaneous capture of liberated protein onto a solid phase. The combination of low temperatures and surface stabilisation enables us to detect epitopes from even partially degraded proteins. The method may have a wide application in forensic, archaeological, soil and earth sciences.

  14. Cancrinite-group minerals behavior at non-ambient conditions

    Science.gov (United States)

    Lotti, Paolo; Gatta, G. Diego; Kahlenberg, Volker; Merlini, Marco; Alvaro, Matteo; Cámara, Fernando

    2014-05-01

    Cancrinite-group minerals occur in the late stages of alkaline (SiO2)-undersaturated magmatism and in related effusive or contact rocks. So far only few studies have been devoted to the description of the thermo-elastic behavior, phase-stability and P /T -structure evolution (at the atomic scale) of this mineral group. Cancrinite-group minerals have an open-framework structure characterized by the [CAN]-topology. The [CAN]-framework shows large 12-ring channels, parallel to the c crystallographic axis, bound by columns of cages, the so-called can units. While very limited chemical variation is observed in the framework composition (the composition is almost always [Si6Al6O24]) a remarkable chemical variability is reported for the extraframework components in the cancrinite-group minerals. Two subgroups can be identified according to the extraframework content of the can units: the cancrinite- and the davyne-subgroups, showing Na-H2O and Ca-Cl chains, respectively. The channels are stuffed by cations, anions and molecules. We aimed to model the thermo-elastic behavior and the mechanisms of the (P ,T)-induced structure evolution of cancrinite-group minerals, with special interest on the role played by the extraframework population. The study was restricted to the following (CO3)-rich and (SO4)-rich end-members: cancrinite sensu stricto {[(Na,Ca)6(CO3)1.2-1.7][Na2(H2O)2][Al6Si6O24]}, vishnevite {[(Na,Ca,K)6(SO4)][Na2(H2O)2][Al6Si6O24]}, balliranoite {[(Na,Ca)6(CO3)1.2-1.7][Ca2Cl2][Al6Si6O24]} and davyne {[(Na,Ca,K)6((SO4),Cl)][Ca2Cl2][Al6Si6O24]}. Their high-P and low-T (T single-crystal X-ray diffraction, using diamond-anvil cells and (N2)-cryosystems, respectively. The high-T behavior of cancrinite has also been studied by means of in-situ single-crystal X-ray diffraction with a resistive heater. Cancrinite minerals share a similar volume compressibility and thermal expansivity at ambient conditions (cancrinite has KV 0 = 45(2) GPa and αV,293K = 4.88(8)·10-5 K-1

  15. Thermoluminescence response of gamma-irradiated sesame with mineral dust

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez L, Y. [CSIC, Instituto de Estructura de la Materia, Calle Serrano 121, 28006 Madrid (Spain); Correcher, V. [CIEMAT, Av. Complutense 22, 28040 Madrid (Spain); Garcia G, J. [CSIC, Museo Nacional de Ciencias Naturales, Calle Jose Gutierrez Abascal 2, 28006 Madrid (Spain); Cruz Z, E., E-mail: y.r.l@csic.es [UNAM, Instituto de Ciencias Nucleares, Circuito Exterior s/n, Ciudad Universitaria, 04510 Mexico D. F. (Mexico)

    2011-10-15

    The thermoluminescence (Tl) emission of minerals isolated from Mexican and Indian sesame seeds appear as a good tool to discern between irradiated and non-irradiated samples. According to the X-ray diffraction and environmental scanning microscope, the adhered dust in both samples is mainly composed by different amounts of quartz and feldspars. These mineral phases exhibit (i) enough sensitivity to ionizing radiation inducing good Tl intensity, (ii) high stability of the Tl signal during the storage of the material (i.e. low fading) and (iii) are thermally and chemically stable. Blind tests performed under laboratory conditions, but simulating industrial preservation processes (similar temperature and moisture, and presence of white light), allows to distinguish between 1 KGy gamma-irradiated and non-irradiated samples even 11000 hours (15 months) after the irradiation proceeding. (Author)

  16. Shock melting and vaporization of lunar rocks and minerals.

    Science.gov (United States)

    Ahrens, T. J.; O'Keefe, J. D.

    1972-01-01

    The entropy associated with the thermodynamic states produced by hypervelocity meteoroid impacts at various velocities are calculated for a series of lunar rocks and minerals and compared with the entropy values required for melting and vaporization. Taking into account shock-induced phase changes in the silicates, we calculate that iron meteorites impacting at speeds varying from 4 to 6 km/sec will produce shock melting in quartz, plagioclase, olivine, and pyroxene. Although calculated with less certainty, impact speeds required for incipient vaporization vary from 7 to 11 km/sec for the range of minerals going from quartz to periclase for aluminum (silicate-like) projectiles. The impact velocities, which are required to induce melting in a soil, are calculated to be in the range of 3 to 4 km/sec, provided thermal equilibrium is achieved in the shock state.

  17. Thermoluminescence response of gamma-irradiated sesame with mineral dust

    International Nuclear Information System (INIS)

    Rodriguez L, Y.; Correcher, V.; Garcia G, J.; Cruz Z, E.

    2011-10-01

    The thermoluminescence (Tl) emission of minerals isolated from Mexican and Indian sesame seeds appear as a good tool to discern between irradiated and non-irradiated samples. According to the X-ray diffraction and environmental scanning microscope, the adhered dust in both samples is mainly composed by different amounts of quartz and feldspars. These mineral phases exhibit (i) enough sensitivity to ionizing radiation inducing good Tl intensity, (ii) high stability of the Tl signal during the storage of the material (i.e. low fading) and (iii) are thermally and chemically stable. Blind tests performed under laboratory conditions, but simulating industrial preservation processes (similar temperature and moisture, and presence of white light), allows to distinguish between 1 KGy gamma-irradiated and non-irradiated samples even 11000 hours (15 months) after the irradiation proceeding. (Author)

  18. Cryogenic Minerals in Caves of the Vizhay River (Northern Urals

    Directory of Open Access Journals (Sweden)

    E. P. Bazarova

    2018-03-01

    Full Text Available New information on the cryogenic mineral formations at the two Vizhay River caves (Northern Urals is given.   Calcite with the insignificant gypsum admixture predominates in the cryogenic material composition from both caves. In addition, the metastable phases of calcite, such as monohydrocalcite and ikaite were found. In the Saksofon Cave, calcite forms both spherulites and complanate grains. In Lednikovaya Cave, the major part of cryomaterial is presented by spherulites, which may suggests the significant supersaturation of solution. In Lednikovaya Сave, the distinct concentric structure with the growth zones denotes the cryogenic material formation in a thin water film under the partial thawing of upper part of long-term ice mound in summer. In Saksofon Cave the growth zones in crystals are poorly developed that probably caused by the seasonal glaciation in the cave and cryogenic minerals are younger than those in the Lednikovaya Cave.

  19. 30 CFR 281.8 - Rights to minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Rights to minerals. 281.8 Section 281.8 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE LEASING OF MINERALS OTHER THAN OIL, GAS, AND SULPHUR IN THE OUTER CONTINENTAL SHELF General § 281.8 Rights to minerals. (a) Unless...

  20. Mineral Resource Information System for Field Lab in the Osage Mineral Reservation Estate

    Energy Technology Data Exchange (ETDEWEB)

    Carroll, H.B.; Johnson, William I.

    1999-04-27

    The Osage Mineral Reservation Estate is located in Osage County, Oklahoma. Minerals on the Estate are owned by members of the Osage Tribe who are shareholders in the Estate. The Estate is administered by the Osage Agency, Branch of Minerals, operated by the U.S. Bureau of Indian Affairs (BIA). Oil, natural gas, casinghead gas, and other minerals (sand, gravel, limestone, and dolomite) are exploited by lessors. Operators may obtain from the Branch of Minerals and the Osage Mineral Estate Tribal Council leases to explore and exploit oil, gas, oil and gas, and other minerals on the Estate. Operators pay a royalty on all minerals exploited and sold from the Estate. A mineral Resource Information system was developed for this project to evaluate the remaining hydrocarbon resources located on the Estate. Databases on Microsoft Excel spreadsheets of operators, leases, and production were designed for use in conjunction with an evaluation spreadsheet for estimating the remaining hydrocarbons on the Estate.

  1. Determination of mineral abundances in samples from the exploratory studies facility using x-ray diffraction

    International Nuclear Information System (INIS)

    Roberts, S.; Viani, R.

    1998-01-01

    Tuff samples collected from the Exploratory Studies Facility (ESF) were X-rayed to estimate relative mineral abundances. X-ray analysis was performed on sub-samples of specimens collected from both the Single Heater Test (SHT) and Drift Scale Heater Test (DST) that were used for thermomechanical measurements, as well as samples collected from cores retrieved from boreholes in the Drift Scale Test Area. The abundance of minerals that could affect the behavior of the host rock at repository relevant temperatures is of particular interest. These minerals include crystobalite, which undergoes a phase transition and volume change at elevated temperature (-250 'C), and smectite and clinoptilolite that can dehydrate at elevated temperature with accompanying volume reduction. In addition, the spatial distribution of SiO, polymorphs and secondary minerals may provide evidence for deducing past fluid pathways. The mineral abundances tabulated here include data reported previously in three milestone reports (Roberts and Viani, 1997a,b; Viani and Roberts, 1996) but re-analyzed (see below), as well as previously unreported data. Previous X-ray diffraction analyses of samples from the ESF (Roberts and Viani, 1997a; Viani and Roberts, 1996) utilized the matrix flushing method of Chung (1974) and an internal intensity standard (corundum) to quantify the abundances of the phases present. Although the method is adequate for obtaining relative abundances, its accuracy and precision is limited by the inherent differences between the external standards used to compute the reference intensity ratio and the mineral phases in the sample. In a subsequent report (Roberts and Viani, 1997b) mineral abundances were obtained using the Rietveld method of whole X-ray pattern fitting (Snyder and Bish, 1989; Young, 1993). The Rietveld technique has the potential to be both more accurate and more precise for estimating mineral abundances (Snyder and Bish, 1989)

  2. Mars analog minerals' spectral reflectance characteristics under Martian surface conditions

    Science.gov (United States)

    Poitras, J. T.; Cloutis, E. A.; Salvatore, M. R.; Mertzman, S. A.; Applin, D. M.; Mann, P.

    2018-05-01

    We investigated the spectral reflectance properties of minerals under a simulated Martian environment. Twenty-eight different hydrated or hydroxylated phases of carbonates, sulfates, and silica minerals were selected based on past detection on Mars through spectral remote sensing data. Samples were ground and dry sieved to <45 μm grain size and characterized by XRD before and after 133 days inside a simulated Martian surface environment (pressure 5 Torr and CO2 fed). Reflectance spectra from 0.35 to 4 μm were taken periodically through a sapphire (0.35-2.5 μm) and zinc selenide (2.5-4 μm) window over a 133-day period. Mineral stability on the Martian surface was assessed through changes in spectral characteristics. Results indicate that the hydrated carbonates studied would be stable on the surface of Mars, only losing adsorbed H2O while maintaining their diagnostic spectral features. Sulfates were less stable, often with shifts in the band position of the SO, Fe, and OH absorption features. Silicas displayed spectral shifts related to SiOH and hydration state of the mineral surface, while diagnostic bands for quartz were stable. Previous detection of carbonate minerals based on 2.3-2.5 μm and 3.4-3.9 μm features appears to be consistent with our results. Sulfate mineral detection is more questionable since there can be shifts in band position related to SO4. The loss of the 0.43 μm Fe3+ band in many of the sulfates indicate that there are fewer potential candidates for Fe3+ sulfates to permanently exist on the Martian surface based on this band. The gypsum sample changed phase to basanite during desiccation as demonstrated by both reflectance and XRD. Silica on Mars has been detected using band depth ratio at 1.91 and 1.96 μm and band minimum position of the 1.4 μm feature, and the properties are also used to determine their age. This technique continues to be useful for positive silica identifications, however, silica age appears to be less consistent

  3. Dynamics of water confined in clay minerals

    International Nuclear Information System (INIS)

    Le Caer, S.; Pommeret, S.; Renault, J.Ph.; Lima, M.; Righini, R.; Gosset, D.; Simeone, D.; Bergaya, F.

    2012-01-01

    Ultrafast infrared spectroscopy of the O-D stretching mode of dilute HOD in H 2 O probes the local environment and the hydrogen bond network of confined water. The dynamics of water molecules confined in the interlayer space of montmorillonites (Mt) and in interaction with two types of cations (Li + and Ca 2+ ) but also with the negatively charged siloxane surface are studied. The results evidence that the OD vibrational dynamics is significantly slowed down in confined media: it goes from 1.7 ps in neat water to 2.6 Ps in the case of Li + cations with two water pseudo-layers (2.2-2.3 ps in the case of Ca 2+ cations) and to 4.7 ps in the case of Li + cations with one water pseudo-layer. No significant difference between the two cations is noticed. In this 2D confined geometry (the interlayer space being about 0.6 nm for two water pseudo-layers), the relaxation time constants obtained are comparable to the ones measured in analogous concentrated salt solutions. Nevertheless, and in strong opposition to the observations performed in the liquid phase, anisotropy experiments evidence the absence of rotational motions on a 5 ps time scale, proving that the hydrogen bond network in the interlayer space of the clay mineral is locked at this time scale. (authors)

  4. Recovering byproduct heavy minerals from sand and gravel, placer gold, and industrial mineral operations

    Energy Technology Data Exchange (ETDEWEB)

    Gomes, J.M.; Martinez, G.M.; Wong, M.M.

    1979-01-01

    The Bureau of Mines, as part of an effort to maximize minerals and metals recovery from domestic resources, has investigated the feasibility of recovering heavy minerals as byproducts from sand and gravel, placer gold, and industrial mineral operations in northern California. Sand samples from about 50 locations were treated by gravity separation to yield heavy-mineral cocentrates (black sands). Mineral compositions of the concentrates were determined by chemical analysis and mineralogical examination. Individual zircon, ilmenite, magnetite, platinum-group metals, thoria, and silica products were prepared from heavy-mineral concentrates by selective separation using low- and high-intensity magnetic, high-tension, and flotation equipment.

  5. Minerals Policy Statement 2: controlling and mitigating the environmental effects of minerals extraction in England

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-03-15

    Minerals Policy Statement 2 (MPS2) sets out the policies and considerations that the UK Government expects Mineral Planning Authorities to follow when preparing development plans and in considering application for minerals development. This supercedes Minerals Policy Guidance 11 (MPG 11). Annex 1: Dust to MPS2 sets out the policy considerations in relation to dust from mineral workings and associated operations, and how they should be dealt with in local development plans and in considering individual applications. Annex 2: Noise to MPS2 addresses policy in relation to noise from mineral workings. These have been abstracted separately for the Coal Abstracts database. 58 refs., 2 apps.

  6. Canadian minerals yearbook : 2004 review and outlook

    International Nuclear Information System (INIS)

    2004-01-01

    The main focus of the CMY publication is the non-fuel mineral industry, together with uranium, although all mineral fuels are normally included when the total value of Canada's mineral production is reported. The Yearbook includes chapters devoted to each major mineral commodity produced in Canada: aluminum, coal, copper, diamonds, gold, iron ore, magnesium, nickel, potash, salt, silica, and uranium. The subject matter spans all stages of mineral industry activity from geoscience and exploration, through mining and processing, to markets and use. Although domestic issues receive the greatest attention in each chapter, international developments may also be reviewed because of the global nature of the mineral industry and the significant impact that such developments could have on the Canadian industry

  7. Mining and minerals policy: 1976 bicentennial edition

    Energy Technology Data Exchange (ETDEWEB)

    1976-07-01

    The report is organized into three basic parts. The first part, the Executive Summary, provides a brief description of the major topics and lists the issues and recommendations. The report then is divided into two sections. Section I, Summary, is comprised of three chapters: Increased Energy Security; Metals and Nonmetallic Minerals; and Trends and Events. Section II, Issues in Energy and Minerals Policy, is comprised of seven chapters: Federal Leasing; The Federal Role in Reducing the Fiscal Impacts of Energy Development; Availability of Federal Lands for Mineral Exploration and Development; Environmental Issues and the Mineral Industry; Developments in International Minerals Trade and Investment; Ocean Mining; and The Development of New Tools for Energy and Minerals Policy Analysis. (MCW)

  8. Qualitative soil mineral analysis by EDXRF, XRD and AAS probes

    International Nuclear Information System (INIS)

    Singh, Virendra; Agrawal, H.M.

    2012-01-01

    Soil minerals study is vital in terms of investigating the major soil forming compounds and to find out the fate of minor and trace elements, essential for the soil–plant interaction purpose. X-ray diffraction (XRD) has been a popular technique to search out the phases for different types of samples. For the soil samples, however, employing XRD is not so straightforward due to many practical problems. In the current approach, principal component analysis (PCA) has been used to have an idea of the minerals present, in qualitative manner, in the soil under study. PCA was used on the elemental concentrations data of 17 elements, determined by the energy dispersive X-ray fluorescence (EDXRF) technique. XRD analysis of soil samples has been done also to identify the minerals of major elements. Some prior treatments, like removal of silica by polytetrafluoroethylene (PTFE) slurry and grinding with alcohol, were given to samples to overcome the peak overlapping problems and to attain fine particle size which is important to minimize micro-absorption corrections, to give reproducible peak intensities and to minimize preferred orientation. A 2θ step of 0.05°/min and a longer dwell time than normal were used to reduce interferences from background noise and to increase the counting statistics. Finally, the sequential extraction procedure for metal speciation study has been applied on soil samples. Atomic absorption spectroscopy (AAS) was used to find the concentrations of metal fractions bound to various forms. Applying all the three probes, the minerals in the soils can be studied and identified, successfully. - Highlights: ► Qualitative soil minerals analysis by EDXRF, AAS and XRD methods. ► There is a requirement of other means and methods due to inadequacy of XRD. ► Principal component analysis (PCA) provides an idea of minerals present in soil. ► Trace elements complexes can be determined by AAS probe. ► EDXRF, AAS and XRD, in combination, enable

  9. Moisture dependent thermal properties of hydrophilic mineral wool: application of the effective media theory

    Directory of Open Access Journals (Sweden)

    Iñigo Antepara

    2015-09-01

    Full Text Available Thermal properties of mineral wool based materials appear to be of particular importance for their practical applications because the majority of them is used in the form of thermal insulation boards. Every catalogue list of any material producer of mineral wool contains thermal conductivity, sometimes also specific heat capacity, but they give only single characteristic values for dry state of material mostly. Exposure to outside climate or any other environment containing moisture can negatively affect the thermal insulation properties of mineral wool. Nevertheless, the mineral wool materials due to their climatic loading and their environmental exposure contain moisture that can negatively affect their thermal insulation properties. Because the presence of water in mineral wool material is undesirable for the majority of applications, many products are provided with hydrophobic substances. Hydrophilic additives are seldom used in mineral wool products. However, this kind of materials has a good potential for application for instance in interior thermal insulation systems, masonry desalination, green roofs, etc. For these materials, certain moisture content must be estimated and thus their thermal properties will be different than for the dry state. On this account, moisture dependent thermal properties of hydrophilic mineral wool (HMW are studied in a wide range of moisture content using a pulse technique. The experimentally determined thermal conductivity data is analysed using several homogenization formulas based on the effective media theory. In terms of homogenization, a porous material is considered as a mixture of two or three phases. In case of dry state, material consists from solid and gaseous phase. When moistened, liquid phase is also present. Mineral wool consists of the solid phase represented by basalt fibers, the liquid phase by water and the gaseous phase by air. At first, the homogenization techniques are applied for the

  10. Root-driven Weathering Impacts on Mineral-Organic Associations in Deep Soil

    Science.gov (United States)

    Keiluweit, M.; Garcia Arredondo, M.; Tfaily, M. M.; Kukkadapu, R. K.; Schulz, M. S.; Lawrence, C. R.

    2017-12-01

    Plant roots dramatically reshape the soil environments through the release of organic compounds. While root-derived organic compounds are recognized as an important source of soil C, their role in promoting weathering reactions has largely been overlooked. On the one hand, root-driven weathering may generate mineral-organic associations, which can protect soil C for centuries to millennia. On the other hand, root-driven weathering also transforms minerals, potentially disrupting protective mineral-organic associations in the process. Hence root-derived C may not only initiate C accumulation, but also diminish C stocks through disruption of mineral-organic associations. Here we determined the impact of rhizogenic weathering on mineral-organic associations, and associated changes in C storage, across the Santa Cruz Marine Terrace chronosequence (65ka-226ka). Using a combination of high-resolution mass spectrometry, Mössbauer, and X-ray (micro)spectroscopy, we examined mineral-organic associations of deep soil horizons characterized by intense rhizogenic weathering gradients. Initial rhizogenic weathering dramatically increased C stocks, which is directly linked to an increase of microbially-derived C bound to monomeric Fe and Al and nano-goethite. As weathering proceeded, the soil C stocks declined concurrent with an increasingly plant-derived C signature and decreasing crystallinity. X-ray spectromicroscopic analyses revealed strong spatial associations between C and Fe during initial weathering stages, indicative of protective mineral-organic associations. In contrast, later weathering stages showed weaker spatial relationships between C and Fe. We conclude that rhizogenic weathering enhance C storage by creating protective mineral-organic associations in the initial weathering stages. As root-driven weathering proceeds, minerals are transformed into more crystalline phases that retain lower amounts of C. Our results demonstrate that root-induced weathering

  11. Water mineralization and its importance for health

    OpenAIRE

    N. Babio; C. Ferreira-Pêgo; F. Maraver Eyzaguirre; I. Vitoria Miñana; J. Salas-Salvadó

    2016-01-01

    Water mineralization and its importance for health La mineralización del agua y su importancia para la salud. Water is essential for life, participating in the metabolism of all the living organisms. In recent years, the consumption of tap water has decreased and the consumption of bottled water has increased worldwide. The mineral quality and composition of natural mineral water is known and constantly over the year, and their potential effects on health must be determined. Only magnes...

  12. Role of minerals in animal health disorders

    Directory of Open Access Journals (Sweden)

    Sinovec Zlatan J.

    2005-01-01

    Full Text Available All mineral matter, essential or non-essential, can have a significant influence on production results and the health of animals, if large quantities of them are present in a feed ration. A maximally tolerant content depends on the animal specie and category. Many factors, such as physiological status (growth, lactation, etc., nutritive status, content and ratio of nutritive matter in the ration, duration of exposure, and the biological level of utilization of elements, also affect the maximally tolerant content of mineral matter in feed. The content of certain mineral matter in plant feed significantly depends on the soil factor, as well as the content and level of utilization of mineral matter from the soil. Mn, Se and Mo can be present in plant feed in such quantities as to induce toxicosis. Industrial contaminants, Cd, Pb or F, can contaminate plants, in particular their leaves, in quantities which lead to the appearance of clinical signs of conventional toxicosis. Moreover, natural water can contain large quantities of S, F, Na, Mg, or Fe, and certain mineral matter can get into water through industrial waste. In addition to the above, it is possible to cause unwanted effects through the frequent, but primarily unprofessional use of mineral additives, since it is extremely important, besides meeting the mineral requirements of each individual element, to secure a ratio among the mineral matter themselves as well as with other nutritive matter. Mineral matter present in food are in mutual interference, and these relations can be synergistic or antagonistic. The sufficiency of a large number of mineral matter has a negative effect on the utilization of other matter (conditional and/or border deficiency, while certain elements cause the clinical appearance of toxic effects. The accidental intake of large quantities of certain mineral matter is revealed as clinical signs of acute toxicosis, which is very different from chronic effects caused by

  13. Mineral Facilities of Latin America and Canada

    Science.gov (United States)

    Bernstein, Rachel; Eros, Mike; Quintana-Velazquez, Meliany

    2006-01-01

    This data set consists of records for over 900 mineral facilities in Latin America and Canada. The mineral facilities include mines, plants, smelters, or refineries of aluminum, cement, coal, copper, diamond, gold, iron and steel, nickel, platinum-group metals, salt, and silver, among others. Records include attributes such as commodity, country, location, company name, facility type and capacity if applicable, and generalized coordinates. The data were compiled from multiple sources, including the 2003 and 2004 USGS Minerals Yearbooks (Latin America and Candada volume), data to be published in the 2005 Minerals Yearbook Latin America and Canada Volume, minerals statistics and information from the USGS minerals information Web site (minerals.usgs.gov/minerals), and data collected by USGS minerals information country specialists. Data reflect the most recent published table of industry structure for each country. Other sources include statistical publications of individual countries, annual reports and press releases of operating companies,and trade journals. Due to the sensitivity of some energy commodity data, the quality of these data should be evaluated on a country-by-country basis. Additional information and explanation is available from the country specialists.

  14. Mineral legislations applicable to beach sand industry

    International Nuclear Information System (INIS)

    D'Cruz, Eric

    2016-01-01

    India has got a wealth of natural resources in different geological environs and shoreline placers form an important constituent of the natural resources. Large reserves of beach sand minerals, viz. imenite, rutile, leucoxene, zircon, sillimanite, garnet and monazite are the economic minerals in the coastal and inland placer sands. In the federal structure of India, the State Governments are the owners of minerals located within their respective boundaries. The State Governments grant the mineral concessions for all the minerals located within the boundary of the State, under the provisions of the Acts and Rules framed for the purpose. Though the mineral wealth is under the control of the State, the power for framing the rules for the grant of mineral concessions vastly rest with the Central Government. Since mineral concessions are often granted for a longer duration of thirty to fifty years or more, a historical perspective of these rules are imperative in understanding the issues involved with BSM mining industry. Under the Govt. of India Act, 1935, Regulation of Mines and Oilfields and Mineral Development was kept under Federal control, declared by Federal Law. The word 'Federal' was substituted by the word 'Dominion' by the India (Provincial Constitution) Order, 1947. No legislation was, however, enacted in pursuance of above power until after Independence. However, the Govt. on India made the Mining Concession (Central) Rules, 1939 for regulating grants of prospecting license

  15. Increasing strategic role for SA's minerals

    International Nuclear Information System (INIS)

    Anon.

    1977-01-01

    The strategic importance of South Africa's vast mineral resources has been strongly underlined by the Minister of Defence, Mr P.W. Botha. It was pointed out that South Africa ranked among the world's five biggest suppliers of nonfuel minerals and that she has demonstrated her potential as the West's most important source of minerals and strategic raw materials. South Africa therefore exercise a very important stabilising influence on the supply and prices of critical, strategic minerals and raw materials, regarded as of the greatest importance to the Western economy

  16. Proximate, Mineral and Phytochemical Composition of Dioscorea ...

    African Journals Online (AJOL)

    ADOWIE PERE

    Keywords: Dioscorea dumetorum, proximate composition, mineral analysis, phytochemical screening ... were analyzed using atomic absorption ... determined using a Hack Dr/200 Spectrophotometer. ... Lead Acetate. +. +. + .... cosmetics.

  17. Plasmid-mediated mineralization of 4-chlorobiphenyl

    International Nuclear Information System (INIS)

    Shields, M.S.; Hooper, S.W.; Sayler, G.S.

    1985-01-01

    Strains of Alcaligenes and Acinetobacter spp. were isolated from a mixed culture already proven to be proficient at complete mineralization of monohalogenated biphenyls. These strains were shown to harbor a 35 x 10(6)-dalton plasmid mediating a complete pathway for 4-chlorobiphenyl (4CB) oxidation. Subsequent plasmid curing of these bacteria resulted in the abolishment of the 4CB mineralization phenotype and loss of even early 4CB metabolism by Acinetobacter spp. Reestablishment of the Alcaligenes plasmid, denoted pSS50, in the cured Acinetobacter spp. via filter surface mating resulted in the restoration of 4CB mineralization abilities. 4CB mineralization, however, proved to be an unstable characteristic in some subcultured strains. Such loss was not found to coincide with any detectable alteration in plasmid size. Cultures capable of complete mineralization, as well as those limited to partial metabolism of 4CB, produced 4-chlorobenzoate as a metabolite. Demonstration of mineralization of a purified 14 C-labeled chlorobenzoate showed it to be a true intermediate in 4CB mineralization. Unlike the mineralization capability, the ability to produce a metabolite has proven to be stable on subculture. These results indicate the occurrence of a novel plasmid, or evolved catabolic plasmid, that mediates the complete mineralization of 4CB

  18. Thermodynamic properties of chromium bearing slags and minerals. A review

    Energy Technology Data Exchange (ETDEWEB)

    Xiao Yanping; Holappa, L.

    1996-12-31

    In this report, the thermodynamic properties of chromium bearing slags and minerals were reviewed based on the available information in the literature. It includes the analysing methods for oxidation state of chromium in slags, oxidation state of chromium and activities of chromium oxides in slags and minerals. The phase diagrams of chromium oxide systems and chromium distributions between slag and metal phases are also covered ill this review. Concerning the analysing methods, it was found that most of the available approaches are limited to iron free slag systems and the sample preparation is very sensitive to the analysing results. In silicate slags under reducing atmosphere, divalent and trivalent chromium co-exist in the slags. It is agreed that the fraction of divalent chromium to total chromium increases with higher temperature, lower slag basicity and oxygen potential. For the slags under oxidising atmosphere, trivalent, pentavalent and hexavalent states were reported to be stable. The activities of CrO and CrO{sub 1.5} were concluded to have positive deviation from ideal solution. Slag basicity has a positive effect and temperature has a negative effect on the activities of chromium oxides. The phase diagrams of the Cr-O, binary, and ternary chromium containing oxide systems have been examined systematically. The analysis shows that the data on the quaternary and quinary systems are insufficient, and require further investigation. The most important features of the chromium containing silicate slags are the large miscibility gaps and the stability of the chromite spinel. (orig.) (76 refs.)

  19. Evaluation of the bleaching flux in clays containing hematite and different clay minerals

    International Nuclear Information System (INIS)

    Silva Junior, E.M.; Lusa, T.; Silva, T.M.; Medeiros, B.B.; Santos, G.R. dos; Morelli, M.R.

    2016-01-01

    Previous studies have shown that the addition of a synthetic flux in a clay mineral constituted by illite phase in the presence of iron oxide with the hematite, promotes color change of the firing products, making the reddish color firing into whiteness. This flow is constituted of a vitreous phase of the silicates family obtained by fusion/solidification of oxides and carbonates. Thus, the objective of this work was that of studying the interaction of the iron element in the final color mechanism of the different types of mineral crystal phase of the clays. In order to study the phenomenon, we obtained different compositions between the select clays and the synthetic flow, and characterization using X-ray diffraction (XRD) and visual analysis. The results showed that the action of the synthetic flow as a modifying agent for color depends on the mineral crystal phase of the clays. The color firing modification does not occur in the clays content high levels of kaolinite mineral phase. (author)

  20. Impact of Bioreduction on Remobilization of Adsorbed Cadmium on Iron Minerals in Anoxic Condition.

    Science.gov (United States)

    Ghorbanzadeh, Nasrin; Lakzian, Amir; Halajnia, Akram; Choi, Ui-Kyu; Kim, Ki-Hyun; Kim, Jong-Oh; Kurade, Mayur; Jeon, Byong-Hun

    2017-06-01

      The impact of bioreduction on the remobilization of adsorbed cadmium Cd(II) on minerals, including hematite, goethite, and two iron(III)-rich clay minerals nontronites (NAU-1 and NAU-2) under anoxic conditions was investigated. Langmuir isotherm equation better described the sorption of Cd(II) onto the all minerals. The maximum adsorption capacity was 6.2, 18.1, 3.6, and 4 mg g-1 for hematite, goethite, NAU-1 and NAU-2, respectively. The desorption of Cd(II) was due to the production of Fe(II) as a result of bioreduction of structural Fe(III) in the minerals by Shewanella putrefaciens. The bioreduction of Cd(II)-loaded Fe(III) minerals was negligible during the initial 5 days followed by a rapid increase up to 20 days. The amount of Cd(II) in solution phase at the end of 30 days increased up to 0.07 mmol L-1 for hematite, NAU-1, and NAU-2 and 0.02 mmol L-1 for goethite. The X-ray diffraction study showed negligible changes in bioreduced minerals phases.

  1. The heterogeneous nature of mineral matter, fly-ash and deposits

    Energy Technology Data Exchange (ETDEWEB)

    Creelman, R.A.; Pohl, J.H.; Devir, G.P.; Su, S. [R.A. Creelman and Associates, Epping, NSW (Australia)

    2000-07-01

    This paper reports on a series of slagging studies investigating the heterogeneous nature of mineral matter, fly ash and deposits, and how this heterogeneity affects deposition. The data come from low temperature ashing (LTA) of pulverised coal, fly ash from boilers, and deposits from pilot-scale furnaces and boilers. The paper presents optical and scanning electron (SEM) micrographs, electron microprobe analysis (EMPA) and energy dispersive x-ray analysis (EDXRA) of mineral matter, individual fly ash particles, and localised regions of deposits. During combustion, the included mineral matter is transformed into fly ash, melts and partially adheres to the char surface, and may form agglomerated masses. Excluded mineral matter has little chance of encountering another ash particle and agglomerating in the gas phase, but can react with other particles in the wall deposits. Certain fly ash particles adhere to the wall where they can combine with other fly ash particles. Analyses of molten regions of deposits have shown, so far, four mineral phase fields to be responsible for forming difficult deposits with melting points below deposit surface temperatures of 1200 to 1350{sup o}C. These mineral fields include iron cordierite, albite and its silica undersaturated equivalent nepheline, anorthite, and compounds with ratios of Ca to P of 2.3-2.5.

  2. Determination of bone mineral volume fraction using impedance analysis and Bruggeman model

    Energy Technology Data Exchange (ETDEWEB)

    Ciuchi, Ioana Veronica; Olariu, Cristina Stefania, E-mail: oocristina@yahoo.com; Mitoseriu, Liliana, E-mail: lmtsr@uaic.ro

    2013-11-20

    Highlights: • Mineral volume fraction of a bone sample was determined. • Dielectric properties for bone sample and for the collagen type I were determined by impedance spectroscopy. • Bruggeman effective medium approximation was applied in order to evaluate mineral volume fraction of the sample. • The computed values were compared with ones derived from a histogram test performed on SEM micrographs. -- Abstract: Measurements by impedance spectroscopy and Bruggeman effective medium approximation model were employed in order to determine the mineral volume fraction of dry bone. This approach assumes that two or more phases are present into the composite: the matrix (environment) and the other ones are inclusion phases. A fragment of femur diaphysis dense bone from a young pig was investigated in its dehydrated state. Measuring the dielectric properties of bone and its main components (hydroxyapatite and collagen) and using the Bruggeman approach, the mineral volume filling factor was determined. The computed volume fraction of the mineral volume fraction was confirmed by a histogram test analysis based on the SEM microstructures. In spite of its simplicity, the method provides a good approximation for the bone mineral volume fraction. The method which uses impedance spectroscopy and EMA modeling can be further developed by considering the conductive components of the bone tissue as a non-invasive in situ impedance technique for bone composition evaluation and monitoring.

  3. Synchrotron based mass spectrometry to investigate the molecular properties of mineral-organic associations

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Suet Yi; Kleber, Markus; Takahashi, Lynelle K.; Nico, Peter; Keiluweit, Marco; Ahmed, Musahid

    2013-04-01

    Soil organic matter (OM) is important because its decay drives life processes in the biosphere. Analysis of organic compounds in geological systems is difficult because of their intimate association with mineral surfaces. To date there is no procedure capable of quantitatively separating organic from mineral phases without creating artifacts or mass loss. Therefore, analytical techniques that can (a) generate information about both organic and mineral phases simultaneously and (b) allow the examination of predetermined high-interest regions of the sample as opposed to conventional bulk analytical techniques are valuable. Laser Desorption Synchrotron Postionization (synchrotron-LDPI) mass spectrometry is introduced as a novel analytical tool to characterize the molecular properties of organic compounds in mineral-organic samples from terrestrial systems, and it is demonstrated that when combined with Secondary Ion Mass Spectrometry (SIMS), can provide complementary information on mineral composition. Mass spectrometry along a decomposition gradient in density fractions, verifies the consistency of our results with bulk analytical techniques. We further demonstrate that by changing laser and photoionization energies, variations in molecular stability of organic compounds associated with mineral surfaces can be determined. The combination of synchrotron-LDPI and SIMS shows that the energetic conditions involved in desorption and ionization of organic matter may be a greater determinant of mass spectral signatures than the inherent molecular structure of the organic compounds investigated. The latter has implications for molecular models of natural organic matter that are based on mass spectrometric information.

  4. Determination of bone mineral volume fraction using impedance analysis and Bruggeman model

    International Nuclear Information System (INIS)

    Ciuchi, Ioana Veronica; Olariu, Cristina Stefania; Mitoseriu, Liliana

    2013-01-01

    Highlights: • Mineral volume fraction of a bone sample was determined. • Dielectric properties for bone sample and for the collagen type I were determined by impedance spectroscopy. • Bruggeman effective medium approximation was applied in order to evaluate mineral volume fraction of the sample. • The computed values were compared with ones derived from a histogram test performed on SEM micrographs. -- Abstract: Measurements by impedance spectroscopy and Bruggeman effective medium approximation model were employed in order to determine the mineral volume fraction of dry bone. This approach assumes that two or more phases are present into the composite: the matrix (environment) and the other ones are inclusion phases. A fragment of femur diaphysis dense bone from a young pig was investigated in its dehydrated state. Measuring the dielectric properties of bone and its main components (hydroxyapatite and collagen) and using the Bruggeman approach, the mineral volume filling factor was determined. The computed volume fraction of the mineral volume fraction was confirmed by a histogram test analysis based on the SEM microstructures. In spite of its simplicity, the method provides a good approximation for the bone mineral volume fraction. The method which uses impedance spectroscopy and EMA modeling can be further developed by considering the conductive components of the bone tissue as a non-invasive in situ impedance technique for bone composition evaluation and monitoring

  5. Inhalation hazards to uranium miners

    International Nuclear Information System (INIS)

    Cross, F.T.

    1985-01-01

    This project is investigating levels of uranium mine air contaminants, using both large and small experimental animals to model human respiratory system disease. Lung cancer and deaths by degenerative lung disease have reached epidemic proportions among uranium miners, but the cause-effect relationships for these diseases are based on inadequate epidemiological data. This project identifies agents or combinations of agents (both chemical and radiological), and their exposure levels, that produce respiratory tract lesions, including respiratory epithelial carcinoma, pneumoconiosis, and emphysema. Histopathologic data from rats are shown for approximately 300- to 10,000-working-level-month (WLM) radon-daughter exposures. Exposure of male rats to radon daughters and uranium ore dust continues, along with exposure of male and female beagle dogs to uranium ore dust alone. 4 tables

  6. Inhalation hazards to uranium miners

    International Nuclear Information System (INIS)

    Cross, F.T.

    1986-01-01

    This project is investigating levels of uranium mine air contaminants, using both large and small experimental animals to model human respiratory system diseases. Lung cancer and deaths by degenerative lung disease have reached epidemic proportions among uranium miners, but the cause-effect relationships for these diseases are based on inadequate epidemiological data. This project identifies uranium mine air agents or combinations of agents (both chemical and radiological), and their exposure levels, that produce respiratory tract lesions, including respiratory epithelial carcinoma, pneumoconiosis, and emphysema. Histopathologic data from serially sacrificed rats are reported for approximately 20- to 640- working-level-month (WLM) radon-daughter exposures delivered at one-tenth the rate of previous exposures. Exposure of male rats to radon daughters and uranium ore dust continues, along with exposure of male and female beagle dogs to uranium ore dust alone

  7. Zirconium - an imported mineral commodity

    International Nuclear Information System (INIS)

    1983-10-01

    This report examines Canada's position in regard to the principal zirconium materials: zircon; fusion-cast zirconium-bearing refractory products; zirconium-bearing chemicals; and zirconium metal, master alloys, and alloys. None of these is produced in Canada except fused alumina-zirconia and certain magnesium-zirconium alloys and zirconium-bearing steels. Most of the 3 000-4 000 tonnes of the various forms of zircon believed to be consumed in Canada each year is for foundry applications. Other minerals, notably chromite, olivine and silica sand are also used for these purposes and, if necessary, could be substituted for zircon. Zirconium's key role in Canada is in CANDU nuclear power reactors, where zirconium alloys are essential in the cladding for fuel bundles and in capital equipment such as pressure tubes, calandria tubes and reactivity control mechanisms. If zirconium alloys were to become unavailable, the Canadian nuclear power industry would collapse. As a contingency measure, Ontario Hydro maintains at least nine months' stocks of nuclear fuel bundles. Canada's vulnerability to short-term disruptions to supplies of nuclear fuel is diminished further by the availability of more expensive electricity from non-nuclear sources and, given time, from mothballed thermal plants. Zirconium minerals are present in many countries, notably Australia, the Republic of South Africa and the United States. Australia is Canada's principal source of zircon imports; South Africa is its sole source of baddeleyite. At this time, there are no shortages of either material. Canada has untapped zirconium resources in the Athabasca Oil Sands (zircon) and at Strange Lake along the ill-defined border between Quebec and Newfoundland (gittinsite). Adequate metal and alloy production facilities exist in France, Japan and the United States. No action by the federal government in regard to zirconium supplies is called for at this time

  8. The mineralization and mechanism of the endogenetic mineral deposit in China

    International Nuclear Information System (INIS)

    Jiang Yonghong

    2010-01-01

    In the process of mineralization, due to the difference in rank, scale and order of structures orebody, mine colomn or rich ore bag are often produced in the specific structural parts. Obviously, it is controlled by favourite structure. The important and direct control of the structure to metal endogenetic mineralization evolution are representative on the affect of pulse action of structure to the multi-stage of mineralization evolution. According to the formation environment of the mineralization, it can be classified as collision orogeny mineralization, release(extension)mineralization, slide draw-division basin mineralization and shear zone extension mineralization. Throng the discuss of endogenetic deposit in the geological evolution, structure and formation machenism, the metallogenic model was preliminary established,and the criteria for delineating favourable metallogenic area was identified. (authors)

  9. Mode of distribution of uranium mineralization and sequence of the formation of minerals in albitites

    International Nuclear Information System (INIS)

    Grechishnikov, N.P.; Kramar, O.A.; Rapovich, F.I.

    1985-01-01

    On the basis of analysis and generalization of factural material data on the distribution nature of accessory uranium mineralization in albitites permitting to judge of the role and textural-structural peculiarities of enclosing rocks in mineralization localization are given. It is shown that the uranium mineral formation is closely related with the albitite formation and proceeded during two stages. A main mass of primary uranium minerals (brannerites and uraninites) in the form of impregnated mineralization was formed during the first uraninite-brannerite-albitite stage. Uranium oxides, silicates and titanates in the shape of veines formed. During the second coffinite-pitchblende-chloritic stage the formation of uranium oxides, silicates and titanates occured. Uranium mineralization in albitites developes in zones of cataclasm, small jointing, mylonitization localizing in fine-grained aggregates. A main mass of primary uranium minerals in albitites (brannerite, uraninite relates to neogenic during metasomatosis dark-coloured minerals (riebenite, aegirine, chlorite)

  10. Characterization of Rare Earth Element Minerals in Coal Utilization Byproducts

    Energy Technology Data Exchange (ETDEWEB)

    Montross, Scott N. [Oak Ridge Inst. for Science and Education (ORISE), Oak Ridge, TN (United States); Verba, Circe A. [National Energy Technology Lab. (NETL), Albany, OR (United States). Research Innovation Center; Collins, Keith [National Energy Technology Lab. (NETL), Albany, OR (United States). Research Innovation Center

    2017-07-17

    The United States currently produces over 100 million tons of coal utilization byproducts (CUB) per year in the form of fly ash, bottom ash, slag, and flue gas (American Coal Ash Association (ACCA), 2015). But this “waste material” also contains potentially useful levels of rare earth elements (REE). Rare earth elements are crucial for many existing and emerging technologies, but the U.S. lacks a domestic, sustainable REE source. Our project explored the possibility of developing a supply of REEs for U.S. technologies by extracting REEs from CUBs. This work offers the potential to reduce our dependence on other countries for supply of these critical elements (NETL, REE 2016 Project Portfolio). Geologic and diagenetic history, industrial preparation methods, and the specific combustion process all play major roles in the composition of CUB. During combustion, inorganic mineral phases of coal particles are fluidized at temperatures higher than 1400oC, so inorganic mineral materials are oxidized, fused, disintegrated, or agglomerated into larger spherical and amorphous (non-crystalline) particles. The original mineralogy of the coal-containing rock and heating/cooling of the material significantly affects the composition and morphology of the particles in the combustion byproduct (Kutchko and Kim, 2006). Thus, different types of coal/refuse/ash must be characterized to better understand mineral evolution during the combustion process. Our research focused on developing a working model to address how REE minerals behave during the combustion process: this research should help determine the most effective engineering methods for extracting REEs from CUBs. We used multimodal imaging and image processing techniques to characterize six rock and ash samples from different coal power plants with respect to morphology, grain size, presence of mineral phases, and elemental composition. The results of these characterization activities provided thresholds for realizing the

  11. Impact of activated carbon, biochar and compost on the desorption and mineralization of phenanthrene in soil

    International Nuclear Information System (INIS)

    Marchal, Geoffrey; Smith, Kilian E.C.; Rein, Arno; Winding, Anne; Wollensen de Jonge, Lis; Trapp, Stefan; Karlson, Ulrich G.

    2013-01-01

    Sorption of PAHs to carbonaceous soil amendments reduces their dissolved concentrations, limiting toxicity but also potentially biodegradation. Therefore, the maximum abiotic desorption of freshly sorbed phenanthrene (≤5 mg kg −1 ) was measured in three soils amended with activated carbon (AC), biochar or compost. Total amounts of phenanthrene desorbed were similar between the different soils, but the amendment type had a large influence. Complete desorption was observed in the unamended and compost amended soils, but this reduced for biochar (41% desorbed) and AC (8% desorbed). Cumulative amounts mineralized were 28% for the unamended control, 19% for compost, 13% for biochar and 4% for AC. Therefore, the effects of the amendments in soil in reducing desorption were also reflected in the extents of mineralization. Modeling was used to analyze key processes, indicating that for the AC and charcoal treatments bacterial activity did not limit mineralization, but rather desorption into the dissolved phase. -- Highlights: •Phenanthrene desorption and mineralization compared in soils with activated carbon, charcoal or compost. •Only activated charcoal and biochar hindered both desorption and mineralization. •A linear relationship was found between the extents desorbed and mineralized. •Modelling indicated that bacterial activity was not limiting but that desorption was. -- Extraction into an exhaustive silicone sink measures the maximum phenanthrene desorption from soils with amendments, and this is reflected in the extent of mineralization

  12. Geology of the Vienna Mineralized Area, Blaine and Camas Counties, Idaho

    Science.gov (United States)

    Mahoney, J. Brian; Horn, Michael C.

    2005-01-01

    The Vienna mineralized area of south-central Idaho was an important silver-lead-producing district in the late 1800s and has intermittently produced lead, silver, zinc, copper, and gold since that time. The district is underlain by biotite granodiorite of the Cretaceous Idaho batholith, and all mineral deposits are hosted by the biotite granodiorite. The granodiorite intrudes Paleozoic sedimentary rocks of the Sun Valley Group, is overlain by rocks of the Eocene Challis Volcanic Group, and is cut by numerous northeast-trending Eocene faults and dikes. Two mineralogically and texturally distinct vein types are present in a northwest- and east-trending conjugate shear-zone system. The shear zones postdate granodiorite emplacement and joint formation, but predate Eocene fault and dike formation. Ribbon veins consist of alternating bands of massive vein quartz and silver-sulfide (proustite and pyrargyrite) mineral stringers. The ribbon veins were sheared and brecciated during multiple phases of injection of mineralizing fluids. A quartz-sericite-pyrite-galena vein system was subsequently emplaced in the brecciated shear zones. Both vein systems are believed to be the product of mesothermal, multiphase mineralization. K-Ar dating of shear-zone sericite indicates that sericitization occurred at 80.7?2.8 Ma; thus mineralization in the Vienna mineralized area probably is Late Cretaceous in age.

  13. Geology and Uranium Mineralization of Tanah Merah and Dendang Arai Sectors, West Kalimantan

    International Nuclear Information System (INIS)

    Bambang-Soetopo

    2004-01-01

    Tanah Merah and Dendang Arai sectors are one of the mineralized sectors at Kalan. Goal of this study is to understand the relationship between geology and uranium mineralization character of Tanah Merah and Dendang Arai sectors. In general geology of Tanah Merah is similar with Dendang Arai which consist of biotite quartzite, leopard quartzite, muscovite quartzite, biotite muscovite quartzite, metasilt, metapelite, and granite. The folding is anticline with axel N45F in direction. The prominent fault is NE-SW sinistral fault, NW-SE dextral fault and N-S normal faults. U mineralization fills in the area space between minerals and also as the vein that fill in the fracture system W-E to WNW-ESE in direction. The thickness of mineralization is milimetric to centrimetric. Uranium minerals are uraninite, monazite, autunite and gummite associated with feldspar, tourmaline, zircon, biotite, quartz, pyrite, pyrhotite, hematite, rutile, chalcopyrite, magnenite ilmenite and molybdenite. Radiometric value is in the range of 1.000 to 15.000 c/s and the total grade of U are 12.6 to 2661.25 ppm. U mineralization process connected with intrusion of granite and in the secondary phase. (author)

  14. Uranium mineralization at Lagoa Real, BA, Brazil: the role of fluids in its genesis

    International Nuclear Information System (INIS)

    Prates, Sonia Pinto; Neves, Jose Marques Correia; Fuzikawa, Kazuo

    2009-01-01

    The Lagoa Real uranium province is situated in the central-south of Bahia state . Brazil and it is presently by far the most important and best known uranium occurrence in Brazil. Nowadays 34 anomalies are known in a 30 Km long and 5 km wide area. An open pit mine was open in Cachoeira Mine, in the north portion of the area, and it is the only uranium mine in operation in Brazil and even in South America as well. The uranium mineralization in the Lagoa Real uranium province occurs in metamorphic rocks named albitites, due to their albite content (over 70%). Uraninite is the main uranium mineral, followed by pechblende, uranophane, torbernite and other uranyl minerals. Uraninite occurs as tiny round and irregular crystals (20 a 30 μm) included or associated to mafic minerals, mainly pyroxene and garnet, and also to amphibole and biotite and sometimes to albite. Some secondary minerals such as, for instance, uranophane, torbernite and tyuyamunite are also found. The main albitites minerals from the Cachoeira mine (plagioclase, garnet, biotite, pyroxene, amphibole and titanite) were studied by means of Infrared Spectroscopy Techniques. Good results were obtained from small quantities of material (around 2 mg) and allowed the minerals identification, and also to know their composition (from the peak position) and to detect the presence of water molecules, which indicates an aqueous phase during the uranium formation, probably rich in Fluorine. (author)

  15. Irradiated black pepper identification based on thermoluminescence of silicate minerals

    International Nuclear Information System (INIS)

    Faycal Kharfi; Randa Ketfi

    2018-01-01

    In this work we have successfully implemented thermoluminescence TL method for irradiated food identification. First tests are performed on Indian black pepper and show promising results to extend the proposed method to many other foods. The X-ray diffraction (XRD) shows that SiO 2 (p3 2 21) is the main component of the separated mineral phase. A saturation dose of ∼ 100 Gy is determined for this pepper above which all thermoluminescent centers of the quartz are activated. Thus, above this threshold dose, only the pepper irradiation will be confirmed but no accuracy on the exact dose received. (author)

  16. Thermally unstable complexants/phosphate mineralization of actinides

    International Nuclear Information System (INIS)

    Nash, K.

    1996-01-01

    In situ immobilization is an approach to isolation of radionuclides from the hydrosphere that is receiving increasing attention. Rather than removing the actinides from contaminated soils, this approach transforms the actinides into intrinsically insoluble mineral phases resistant to leaching by groundwater. The principal advangates of this concept are the low cost and low risk of operator exposure and/or dispersion of the radionuclides to the wider environment. The challenge of this approach is toe accomplish the immobilization without causing collateral damage to the environment (the cure shouldn't be worse than the disease) and verification of system performance

  17. Geothermal alteration of clay minerals and shales: diagenesis

    Energy Technology Data Exchange (ETDEWEB)

    Weaver, C.E.

    1979-07-01

    The objective of this report is to perform a critical review of the data on the mineral and chemical alterations that occur during diagenesis and low-grade metamorphism of shale and other clay-rich rocks - conditions similar to those expected from emplacement of heat-producing radioactive waste in a geologic repository. The conclusions drawn in this document are that the following type of alterations could occur: smectite alteration, ion mobilization, illitic shales, kaolinite reactions, chlorite reactions, organic reactions, paleotemperatures, low temperature shales, high temperature shales, and phase equilibrium changes.

  18. Thermodynamic and structural characteristics of cement minerals at elevated temperature

    International Nuclear Information System (INIS)

    Bruton, C.J.; Meike, A.; Viani, B.E.; Martin, S.; Phillips, B.L.

    1994-05-01

    We have instituted an experimental and including program designed to elucidate the structural and thermodynamic response of cement minerals to elevated temperature. Components of the program involve: (a) synthesis of hydrated Ca-silicates; (b) structural analysis of cement phases induced by heating and dehydration/rehydration; (c) mechanistic and thermodynamic descriptions of the hydration/dehydration behavior of hydrated Ca-silicates as a function of temperature, pressure and relative humidity; (d) study of naturally occurring hydrated Ca-silicates; and (e) measurements of thermodynamic data for hydrated Ca-silicates

  19. Geothermal alteration of clay minerals and shales: diagenesis

    International Nuclear Information System (INIS)

    Weaver, C.E.

    1979-07-01

    The objective of this report is to perform a critical review of the data on the mineral and chemical alterations that occur during diagenesis and low-grade metamorphism of shale and other clay-rich rocks - conditions similar to those expected from emplacement of heat-producing radioactive waste in a geologic repository. The conclusions drawn in this document are that the following type of alterations could occur: smectite alteration, ion mobilization, illitic shales, kaolinite reactions, chlorite reactions, organic reactions, paleotemperatures, low temperature shales, high temperature shales, and phase equilibrium changes

  20. Silver-bearing minerals in the Xinhua hydrothermal vein-type Pb-Zn deposit, South China

    Science.gov (United States)

    Wang, Minfang; Zhang, Xubo; Guo, Xiaonan; Pi, Daohui; Yang, Meijun

    2018-02-01

    Electron probe microanalysis (EPMA) results are reported for newly identified silver-bearing minerals from the Xinhua deposit, Yunkaidashan area, South China. The Xinhua deposit is a hydrothermal vein-type Pb-Zn deposit and is hosted in the Pubei Complex, which consists of a cordierite-biotite granite with a U-Pb zircon age of 244.3 ± 1.8-251.9 ± 2.2 Ma. The mineralization process is subdivided into four mineralization stages, characterized by the following mineral associations: mineralization stage I with quartz, pyrite, and sphalerite; mineralization stage II with siderite, galena, and tetrahedrite; mineralization stage III with quartz and galena; and mineralization stage IV with quartz, calcite, and baryte. Tetrahedrite series minerals, such as freibergite, argentotetrahedrite, and tennantite are the main Ag-bearing minerals in the Xinhua deposit. The greatest concentration of silver occurs in phases from mineralization stage II. Microscopic observations reveal close relationship between galena and tetrahedrite series minerals that mostly occur as irregular inclusions within galena. The negative correlation between Cu and Ag in the lattices of tetrahedrite series minerals suggests that Cu sites are occupied by Ag atoms. Zn substitution for Fe in argentotetrahedrite and Cd substitution for Pb in tetrahedrite are also observed. Micro-thermometric data reveal that both homogenization temperatures and calculated salinities of hydrothermal fluids decrease progressively from the early to the later mineralization stages. The metal ions, such as Ag+, Cu+, Pb2+, and Zn2+, are transported as chlorine complex ions in the early mineralization stage and as bisulfide complex ions in the late mineralization stage, caused by changes in oxygen fugacity, temperature, and pH of the hydrothermal fluids. Because of the varying solubility of different metal ions, Pb2+, Zn2+, and Cu2+ ions are initially precipitated as galena, sphalerite, and chalcopyrite, respectively. With

  1. Study on the correlation between chemical and mineral composition of coal ashes; Sekitanbaibun no kobutsu soseigakuteki kento kagakubutsu sosei to kobutsugakuteki sosei no sokan

    Energy Technology Data Exchange (ETDEWEB)

    Hirato, M.; Nagashima, S.; Okada, S. [Hachinohe Institute of Technology, Aomori (Japan)

    1996-10-28

    Coal ash is a substance that has been mixed into minerals in the earth`s crust during their coalification process. Estimation was made on what kinds of mineral composition have been mixed into coals. Noted first was the kinds of compounds contained in the ash, wherein the ratios of mass in the compounds and minerals were correlated, and selection was made on minerals which are thought correlated. The selection criterion was based on minerals containing silica, alumina, iron oxide, lime and magnesium as compounds. Then, a phase equilibrium line diagram was used to estimate compositions and melting points of minerals which are thought to have been produced from these compounds. By comparing the estimation with the measured melting points of the ashes, mineral compositions thought reasonable were all selected. Assumption was possible on minerals that are thought to have been transferred into coal ash. Compound indications of ashes from 29 kinds of the world`s typical coals were replaced with the subject minerals and expressed as mineral compositions. As a method of calculation, stoichiometric coefficients for each mineral were determined by taking material balance in atomic/molecular levels in masses of compound aggregates and mineral composition aggregates. 7 tabs.

  2. Potential function of added minerals as nucleation sites and effect of humic substances on mineral formation by the nitrate-reducing Fe(II)-oxidizer Acidovorax sp. BoFeN1.

    Science.gov (United States)

    Dippon, Urs; Pantke, Claudia; Porsch, Katharina; Larese-Casanova, Phil; Kappler, Andreas

    2012-06-19

    The mobility of toxic metals and the transformation of organic pollutants in the environment are influenced and in many cases even controlled by iron minerals. Therefore knowing the factors influencing iron mineral formation and transformation by Fe(II)-oxidizing and Fe(III)-reducing bacteria is crucial for understanding the fate of contaminants and for the development of remediation technologies. In this study we followed mineral formation by the nitrate-reducing Fe(II)-oxidizing strain Acidovorax sp. BoFeN1 in the presence of the crystalline Fe(III) (oxyhydr)oxides goethite, magnetite and hematite added as potential nucleation sites. Mössbauer spectroscopy analysis of minerals precipitated by BoFeN1 in (57)Fe(II)-spiked microbial growth medium showed that goethite was formed in the absence of mineral additions as well as in the presence of goethite or hematite. The presence of magnetite minerals during Fe(II) oxidation induced the formation of magnetite in addition to goethite, while the addition of humic substances along with magnetite also led to goethite but no magnetite. This study showed that mineral formation not only depends on the aqueous geochemical conditions but can also be affected by the presence of mineral nucleation sites that initiate precipitation of the same underlying mineral phases.

  3. Quantitative analysis of minerals by X-ray diffraction

    International Nuclear Information System (INIS)

    Pietroluongo, L.R.V.; Veiga, M.M. da

    1982-01-01

    Considerations about the X-ray diffraction technique for quantitative analyses are made; some experiments carried out at CETEM - Centro de Tecnologia Mineral (Rio de Janeiro, Brazil) with synthetic samples and real samples of diatomites (from northeastern region of Brazil) are described. Quartz quantification has been a problem for analytical chemists and is of great importance to the industries which use this raw material. Comments are made about the main factors influencing the intensity of diffracted X-rays, such as: the crystallinity of the mineral phase; the granulometry, the preferential orientation; sample preparation and pressing, the chemical composition of standards and experimental analytical conditions. Several analytical methods used are described: direct measurement of the height or area of a peak resulting from a particular reflection and comparison with a pre-calibrated curve; method of sequential addition of the mineral of interest in the sample and extrapolation of results for ZERO addition; methods of external and internal standards. (C.L.B.) [pt

  4. Utilization of mining and mineral wastes

    Energy Technology Data Exchange (ETDEWEB)

    Park, Kyung Ho; Hong, Seung Woong; Choi, Young Yoon; Kim, Byung Gyu; Park, Je Shin [Korea Institute of Geology Mining and Materials, Taejon (Korea)

    1998-12-01

    Up to now, it is estimated that more than 50 million tons of mineral wastes have been generated mining industries and deposited on the land in Korea. Much of cultivated land and hilly areas have been occupied by this wastes, which cause pollution of the environment. Utilization of the mineral wastes is preferable to stabilization because full use would both eliminate the waste and broaden the mineral resource base. Therefore, the development of utilization techniques of mineral wastes is very important not only for improving the environment but also for resource conservation. In countries with high population and poor natural resources like Korea, the utilization of these wastes is essential to decrease the environmental problem and the secure the resources and the study on this field play a important part. Therefore, the objective of this study is to develop the utilization techniques of the mineral wastes. In first year's research, the contents and scope of this study are 1) Present condition and Field Survey on the mineral wastes with respect of their utilization, 2) Reviews of Current effects and research to utilize mineral wastes, 3) Characterization of mineral wastes and environmental test, 4) Evaluation and study on the utilization. (author). 67 refs., 25 tabs., 54 figs.

  5. Mineral exploration, Australia, March quarter 1983

    Energy Technology Data Exchange (ETDEWEB)

    1983-01-01

    This publication contains annual and quarterly statistics of exploration for minerals in Australia. Part 1 sets out statistics of exploration for minerals and oil shale for which data are no longer available for separate publication. Part 2 gives details of petroleum exploration.

  6. Chinese Human Rights Guidance on Minerals Sourcing

    DEFF Research Database (Denmark)

    Buhmann, Karin

    2017-01-01

    in the minerals sector and due diligence to ensure socially responsible sourcing of minerals with a particular focus on human rights, the guidelines refer to international human rights standards and are designed to be consistent with guidance issued by the OECD. The article discusses the Chinese guidelines...

  7. ASEAN Mineral Database and Information System (AMDIS)

    Science.gov (United States)

    Okubo, Y.; Ohno, T.; Bandibas, J. C.; Wakita, K.; Oki, Y.; Takahashi, Y.

    2014-12-01

    AMDIS has lunched officially since the Fourth ASEAN Ministerial Meeting on Minerals on 28 November 2013. In cooperation with Geological Survey of Japan, the web-based GIS was developed using Free and Open Source Software (FOSS) and the Open Geospatial Consortium (OGC) standards. The system is composed of the local databases and the centralized GIS. The local databases created and updated using the centralized GIS are accessible from the portal site. The system introduces distinct advantages over traditional GIS. Those are a global reach, a large number of users, better cross-platform capability, charge free for users, charge free for provider, easy to use, and unified updates. Raising transparency of mineral information to mining companies and to the public, AMDIS shows that mineral resources are abundant throughout the ASEAN region; however, there are many datum vacancies. We understand that such problems occur because of insufficient governance of mineral resources. Mineral governance we refer to is a concept that enforces and maximizes the capacity and systems of government institutions that manages minerals sector. The elements of mineral governance include a) strengthening of information infrastructure facility, b) technological and legal capacities of state-owned mining companies to fully-engage with mining sponsors, c) government-led management of mining projects by supporting the project implementation units, d) government capacity in mineral management such as the control and monitoring of mining operations, and e) facilitation of regional and local development plans and its implementation with the private sector.

  8. Preliminary report about minerals raw materials

    International Nuclear Information System (INIS)

    Bossi, J.

    1965-01-01

    The group of experts entrusted to construct the bases to study the mineral matters has established priorities for the development of mineral resources during the next ten years: 1) aerial photography, 2) geological map, 3) mechanisms for the exploitation, 4) budget

  9. Utilization of mining and mineral wastes

    Energy Technology Data Exchange (ETDEWEB)

    Park, Kyung Ho; Hong, Seung Woong; Choi, Young Yoon; Kim, Byung Gyu; Park, Je Shin [Korea Institute of Geology Mining and Materials, Taejon (Korea)

    1998-12-01

    Up to now, it is estimated that more than 50 million tons of mineral wastes have been generated mining industries and deposited on the land in Korea. Much of cultivated land and hilly areas have been occupied by this wastes, which cause pollution of the environment. Utilization of the mineral wastes is preferable to stabilization because full use would both eliminate the waste and broaden the mineral resource base. Therefore, the development of utilization techniques of mineral wastes is very important not only for improving the environment but also for resource conservation. In countries with high population and poor natural resources like Korea, the utilization of these wastes is essential to decrease the environmental problem and the secure the resources and the study on this field play a important part. Therefore, the objective of this study is to develop the utilization techniques of the mineral wastes. In first year's research, the contents and scope of this study are 1) Present condition and Field Survey on the mineral wastes with respect of their utilization, 2) Reviews of Current effects and research to utilize mineral wastes, 3) Characterization of mineral wastes and environmental test, 4) Evaluation and study on the utilization. (author). 67 refs., 25 tabs., 54 figs.

  10. Mineral resource of the month: potash

    Science.gov (United States)

    Jasinski, Stephen M.

    2011-01-01

    The article offers basic information about the mineral resource potash. According to the author, potash is the generic term for a variety of mined and manufactured salts that contain the mineral potassium in a water-soluble form. The author adds that potash is used in fertilizers, soaps and detergents, glass and ceramics, and alkaline batteries.

  11. Mineral Oils: Untreated and Mildly Treated

    Science.gov (United States)

    Learn about mineral oils, which can raise the risk of nonmelanoma skin cancer, particularly of the scrotum. Workers in a variety of manufacturing industries are most commonly exposed to mineral oils, as are workers in engine repair, copper mining, and commercial printing.

  12. Earth mineral resource of the month: asbestos

    Science.gov (United States)

    Virta, Robert L.

    2010-01-01

    The article discusses the characteristics and feature of asbestos. According to the author, asbestos is a generic name for six needle-shaped minerals that possess high tensile strengths, flexibility, and resistance to chemical and thermal degradation. These minerals are actinolite, amosite, anthophyllite, chrysolite, crocilodite and tremolite. Asbestos is used for strengthening concrete pipe, plastic components, and gypsum plasters.

  13. Near infrared detection of ammonium minerals.

    Science.gov (United States)

    Krohn, M.D.; Altaner, S.P.

    1987-01-01

    Diagnostic near-infrared spectral features have been identified for minerals with ammonium (NH4+) bound in the crystal structure. Near-infrared detection of NH4-bearing minerals may provide useful information for prospecting for certain ore deposits and may provide a better understanding of the nitrogen cycle within geologic environments.-from Authors

  14. Mineral nutrition of cocoa : a review

    NARCIS (Netherlands)

    Vliet, van J.A.; Slingerland, M.A.; Giller, K.E.

    2015-01-01

    This literature review on mineral nutrition of cocoa was commissioned by the Scientific Committee of the Cocoa Fertiliser Initiative to address the following questions: What knowledge is currently available about mineral nutrition of cocoa? What are the current knowledge gaps? What are the key areas

  15. Intracellular transport of ions in mineralizing tissues

    International Nuclear Information System (INIS)

    Matthews, J.L.

    This study resulted in the development of a new model for bone cell physiology and has provided the means for studying the mechanism and site of action of bone affecting hormones and vitamin metabolites and has provided new information on mechanisms of mineralization and mineralization defects

  16. Thermoelastic properties of minerals at high temperature

    Indian Academy of Sciences (India)

    In our present study, we have investigated the thermophysical properties of two minerals (pyrope-rich garnet and MgAl2O4) under high temperatures and calculated the second-order elastic constant () and bulk modulus (T) of the above minerals, in two cases first by taking Anderson–Gruneisen parameter (T) as ...

  17. Isotope analysis of molybdenum in selected minerals

    International Nuclear Information System (INIS)

    Becker, S.; Dietze, H.J.

    1980-01-01

    An analytical method is described for the mass spectrometric determination of molybdenum abundance values. The results of analyses of three molybdenum mineral samples are presented and compared with the results of other authors. It is shown that the fine variations of molybdenum in natural minerals cannot be analysed with currently available mass spectrometers

  18. Morphological Analysis of White Cement Clinker Minerals: Discussion on the Crystallization-Related Defects

    Directory of Open Access Journals (Sweden)

    Mohamed Benmohamed

    2016-01-01

    Full Text Available The paper deals with a formation of artificial rock (clinker. Temperature plays the capital role in the manufacturing process. So, it is useful to analyze a poor clinker to identify the different phases and defects associated with their crystallization. X-ray fluorescence spectroscopy was used to determine the clinker’s chemical composition. The amounts of the mineralogical phases are measured by quantitative XRD analysis (Rietveld. Scanning electron microscopy (SEM was used to characterize the main phases of white Portland cement clinker and the defects associated with the formation of clinker mineral elements. The results of a study which focused on the identification of white clinker minerals and defects detected in these noncomplying clinkers such as fluctuation of the amount of the main phases (alite (C3S and belite (C2S, excess of the free lime, occurrence of C3S polymorphs, and occurrence of moderately-crystallized structures are presented in this paper.

  19. Liquid-Liquid Extraction and Determination of Trace Elements in Iron Minerals by Atomic Absorption Spectrometry

    International Nuclear Information System (INIS)

    Taseska, Milena; Stafilov, Trajche; Makreski, Petre; Jacimovic, Radojko; Jovanovski, Gligor

    2006-01-01

    Various trace elements (cadmium, chromium, cobalt, nickel, manganese) in some iron minerals were determined by flame (FAAS) and electrothermal atomic absorption spectrometry (ETAAS). The studied minerals were chalcopyrite (CuFeS 2 ), hematite (Fe 2 O 3 ) and pyrite (FeS 2 ). To avoid the interference of iron, a method for liquid-liquid extraction of iron and determination of investigated elements in the inorganic phase was proposed. Iron was extracted by diisopropyl ether in hydrochloride acid solution and the extraction method was optimized. Some parameters were obtained to be significantly important: Fe mass in the sample should not exceed 0.3 g, the optimal concentration of HCI should be 7.8 mol 1 -1 and ratio of the inorganic and organic phase should be 1: 1. The procedure was verified by the method of standard additions and by its applications to reference standard samples. The investigated minerals originate from various mines in the Republic of Macedonia. (Author)

  20. Radioactive mineral occurrences in the Bancroft area

    Energy Technology Data Exchange (ETDEWEB)

    Satterly, J

    1958-12-31

    The report summarizes three years of field work conducted in the Bancroft area investigating occurrences of radioactive minerals, and also includes accounts of properties in the area for which drill logs and survey reports have been filed. It begins with a history of exploration and development of radioactive mineral deposits in the area, a review of the area`s general geology (Grenville metasediments, plutonic rocks), and general descriptions of the types of radioactive mineral deposits found in the area (deposits in granitic and syenitic bodies, metasomatic deposits in limy rocks, hydrothermal deposits). It also describes the mineralogy of radioactive minerals found in the area and the Geiger counter technique used in the investigation. The bulk of the report consists of descriptions of radioactive mineral properties and mine workings, containing (where available) information on exploration history, general and economic geology, and production.

  1. Surface analytical techniques applied to minerals processing

    International Nuclear Information System (INIS)

    Smart, R.St.C.

    1991-01-01

    An understanding of the chemical and physical forms of the chemically altered layers on the surfaces of base metal sulphides, particularly in the form of hydroxides, oxyhydroxides and oxides, and the changes that occur in them during minerals processing lies at the core of a complete description of flotation chemistry. This paper reviews the application of a variety of surface-sensitive techniques and methodologies applied to the study of surface layers on single minerals, mixed minerals, synthetic ores and real ores. Evidence from combined XPS/SAM/SEM studies have provided images and analyses of three forms of oxide, oxyhydroxide and hydroxide products on the surfaces of single sulphide minerals, mineral mixtures and complex sulphide ores. 4 refs., 2 tabs., 4 figs

  2. Destabilization of emulsions by natural minerals.

    Science.gov (United States)

    Yuan, Songhu; Tong, Man; Wu, Gaoming

    2011-09-15

    This study developed a novel method to destabilize emulsions and recycle oils, particularly for emulsified wastewater treatment. Natural minerals were used as demulsifying agents, two kinds of emulsions collected from medical and steel industry were treated. The addition of natural minerals, including artificial zeolite, natural zeolite, diatomite, bentonite and natural soil, could effectively destabilize both emulsions at pH 1 and 60 °C. Over 90% of chemical oxygen demand (COD) can be removed after treatment. Medical emulsion can be even destabilized by artificial zeolite at ambient temperature. The mechanism for emulsion destabilization by minerals was suggested as the decreased electrostatic repulsion at low pH, the enhanced gathering of oil microdroplets at elevated temperature, and the further decreased surface potential by the addition of minerals. Both flocculation and coalescence were enhanced by the addition of minerals at low pH and elevated temperature. Copyright © 2011 Elsevier B.V. All rights reserved.

  3. Mineral exploration with ERTS imagery. [Colorado

    Science.gov (United States)

    Nicolais, S. M.

    1974-01-01

    Ten potential target areas for metallic mineral exploration were selected on the basis of a photo-lineament interpretation of the ERTS image 1172-17141 in central Colorado. An evaluation of bias indicated that prior geologic knowledge of the region had little, if any, effect on target selection. In addition, a contoured plot of the frequency of photo-lineament intersections was made to determine what relationships exist between the photo-lineaments and mineral districts. Comparison of this plot with a plot of the mineral districts indicates that areas with a high frequency of intersections commonly coincide with known mineral districts. The results of this experiment suggest that photo-lineaments are fractures or fracture-controlled features, and their distribution may be a guide to metallic mineral deposits in Colorado, and probably other areas as well.

  4. Mineral potential for incompatible element deposits hosted in pegmatites, alkaline rocks, and carbonatites in the Islamic Republic of Mauritania (phase V, deliverable 87): Chapter Q in Second projet de renforcement institutionnel du secteur minier de la République Islamique de Mauritanie (PRISM-II)

    Science.gov (United States)

    Taylor, Cliff D.; Giles, Stuart A.

    2015-01-01

    Review of PRISM-I documents and the National inventory of mineral occurrences suggests that resources of U, Th, Nb, Ta, Be, rare earth elements (REEs) and fluorite are known in Mauritania and have been exploited in the past at the Bou Naga alkaline complex. Several different deposit types are indicated by the available data. Pegmatitic veins are recorded in several areas of the Archean and Paleoproterozoic portions of the Rgueïbat Shield and are prospective for resources of Li, Be, Nb, Ta, U, Th, and REEs. Over 150 beryl pegmatites are known in the Khnefissat and Inkebden areas of the Chami greenstone belt, and additional concentrations of pegmatites are known in the Guelb Nich Sud area of the Sebkhet Nich greenstone belt and in the northeastern part of the Amsaga Complex. Due to the small size of these deposits, they are unlikely to be economic unless additional value can be gained by processing contained minerals for their industrial uses.

  5. An overview of hydrodynamic studies of mineralization

    Directory of Open Access Journals (Sweden)

    Guoxiang Chi

    2011-07-01

    Full Text Available Fluid flow is an integral part of hydrothermal mineralization, and its analysis and characterization constitute an important part of a mineralization model. The hydrodynamic study of mineralization deals with analyzing the driving forces, fluid pressure regimes, fluid flow rate and direction, and their relationships with localization of mineralization. This paper reviews the principles and methods of hydrodynamic studies of mineralization, and discusses their significance and limitations for ore deposit studies and mineral exploration. The driving forces of fluid flow may be related to fluid overpressure, topographic relief, tectonic deformation, and fluid density change due to heating or salinity variation, depending on specific geologic environments and mineralization processes. The study methods may be classified into three types, megascopic (field observations, microscopic analyses, and numerical modeling. Megascopic features indicative of significantly overpressured (especially lithostatic or supralithostatic fluid systems include horizontal veins, sand injection dikes, and hydraulic breccias. Microscopic studies, especially microthermometry of fluid inclusions and combined stress analysis and microthermometry of fluid inclusion planes (FIPs can provide important information about fluid temperature, pressure, and fluid-structural relationships, thus constraining fluid flow models. Numerical modeling can be carried out to solve partial differential equations governing fluid flow, heat transfer, rock deformation and chemical reactions, in order to simulate the distribution of fluid pressure, temperature, fluid flow rate and direction, and mineral precipitation or dissolution in 2D or 3D space and through time. The results of hydrodynamic studies of mineralization can enhance our understanding of the formation processes of hydrothermal deposits, and can be used directly or indirectly in mineral exploration.

  6. Inducing mineral precipitation in groundwater by addition of phosphate

    Directory of Open Access Journals (Sweden)

    Hartmann Thomas

    2011-10-01

    Full Text Available Abstract Background Induced precipitation of phosphate minerals to scavenge trace elements from groundwater is a potential remediation approach for contaminated aquifers. The success of engineered precipitation schemes depends on the particular phases generated, their rates of formation, and their long term stability. The purpose of this study was to examine the precipitation of calcium phosphate minerals under conditions representative of a natural groundwater. Because microorganisms are present in groundwater, and because some proposed schemes for phosphate mineral precipitation rely on stimulation of native microbial populations, we also tested the effect of bacterial cells (initial densities of 105 and 107 mL-1 added to the precipitation medium. In addition, we tested the effect of a trace mixture of propionic, isovaleric, formic and butyric acids (total concentration 0.035 mM. Results The general progression of mineral precipitation was similar under all of the study conditions, with initial formation of amorphous calcium phosphate, and transformation to poorly crystalline hydroxylapatite (HAP within one week. The presence of the bacterial cells appeared to delay precipitation, although by the end of the experiments the overall extent of precipitation was similar for all treatments. The stoichiometry of the final precipitates as well as Rietveld structure refinement using x-ray diffraction data indicated that the presence of organic acids and bacterial cells resulted in an increasing a and decreasing c lattice parameter, with the higher concentration of cells resulting in the greatest distortion. Uptake of Sr into the solids was decreased in the treatments with cells and organic acids, compared to the control. Conclusions Our results suggest that the minerals formed initially during an engineered precipitation application for trace element sequestration may not be the ones that control long-term immobilization of the contaminants. In

  7. Relations of ammonium minerals at several hydrothermal systems in the western U.S.

    Science.gov (United States)

    Krohn, M.D.; Kendall, C.; Evans, J.R.; Fries, T.L.

    1993-01-01

    Ammonium bound to silicate and sulfate minerals has recently been located at several major hydrothermal systems in the western U.S. utilizing newly-discovered near-infrared spectral properties. Knowledge of the origin and mineralogic relations of ammonium minerals at known hydrothermal systems is critical for the proper interpretation of remote sensing data and for testing of possible links to mineralization. Submicroscopic analysis of ammonium minerals from two mercury- and gold-bearing hot-springs deposits at Ivanhoe, Nevada and McLaughlin, California shows that the ammonium feldspar, buddingtonite, occurs as fine-grained euhedral crystals coating larger sulfide and quartz crystals. Ammonium feldspar seems to precipitate relatively late in the crystallization sequence and shows evidence for replacement of NH4+ by K+ or other monovalent cations. Some buddingtonite is observed in close association with mercury, but not with gold. Ammonioalunite is found in a variety of isolated crystal forms at both deposits. Nitrogen isotopic values for ammonium-bearing minerals show a 14??? range in composition, precluding assignment of a specific provenance to the nitrogen. The correlations of nitrogen isotopic values with depth and ammonium content suggest some loss of nitrogen in the oxidizing supergene environment, possibly as a metastable mineral. The high ammonium content in these hydrothermal systems, the close association to mercury, and the small crystal size of the ammonium-bearing minerals all suggest that ammonium may be transported in a late-stage vapor phase or as an organic volatile. Such a process could lead to the formation of a non-carbonaceous organic aureole above a buried geothermal source. The discovery of a 10-km outcrop of ammonium minerals confirms that significant substitution of ammonium in minerals is possible over an extensive area and that remote sensing is a feasible means to detect such aureoles. ?? 1993.

  8. Adsorption and redox reactions of heavy metals on synthesized Mn oxide minerals

    International Nuclear Information System (INIS)

    Feng Xionghan; Zhai Limei; Tan Wenfeng; Liu Fan; He Jizheng

    2007-01-01

    Several Mn oxide minerals commonly occurring in soils were synthesized by modified or optimized methods. The morphologies, structures, compositions and surface properties of the synthesized Mn oxide minerals were characterized. Adsorption and redox reactions of heavy metals on these minerals in relation to the mineral structures and surface properties were also investigated. The synthesized birnessite, todorokite, cryptomelane, and hausmannite were single-phased minerals and had the typical morphologies from analyses of XRD and TEM/ED. The PZCs of the synthesized birnessite, todorokite and cryptomelane were 1.75, 3.50 and 2.10, respectively. The magnitude order of their surface variable negative charge was: birnessite ≥ cryptomelane > todorokite. The hausmannite had a much higher PZC than others with the least surface variable negative charge. Birnessite exhibited the largest adsorption capacity on heavy metals Pb 2+ , Cu 2+ , Co 2+ , Cd 2+ and Zn 2+ , while hausmannite the smallest one. Birnessite, cryptomelane and todorokite showed the greatest adsorption capacity on Pb 2+ among the tested heavy metals. Hydration tendency (pK 1 ) of the heavy metals and the surface variable charge of the Mn minerals had significant impacts on the adsorption. The ability in Cr(III) oxidation and concomitant release of Mn 2+ varied greatly depending on the structure, composition, surface properties and crystallinity of the minerals. The maximum amounts of Cr(III) oxidized by the Mn oxide minerals in order were (mmol/kg): birnessite (1330.0) > cryptomelane (422.6) > todorokite (59.7) > hausmannite (36.6). - The characteristics of heavy metal adsorption and Cr(III) oxidation on Mn oxide minerals are determined by their structure, composition, surface property and crystallinity

  9. Atom exchange between aqueous Fe(II) and structural Fe in clay minerals.

    Science.gov (United States)

    Neumann, Anke; Wu, Lingling; Li, Weiqiang; Beard, Brian L; Johnson, Clark M; Rosso, Kevin M; Frierdich, Andrew J; Scherer, Michelle M

    2015-03-03

    Due to their stability toward reductive dissolution, Fe-bearing clay minerals are viewed as a renewable source of Fe redox activity in diverse environments. Recent findings of interfacial electron transfer between aqueous Fe(II) and structural Fe in clay minerals and electron conduction in octahedral sheets of nontronite, however, raise the question whether Fe interaction with clay minerals is more dynamic than previously thought. Here, we use an enriched isotope tracer approach to simultaneously trace Fe atom movement from the aqueous phase to the solid ((57)Fe) and from the solid into the aqueous phase ((56)Fe). Over 6 months, we observed a significant decrease in aqueous (57)Fe isotope fraction, with a fast initial decrease which slowed after 3 days and stabilized after about 50 days. For the aqueous (56)Fe isotope fraction, we observed a similar but opposite trend, indicating that Fe atom movement had occurred in both directions: from the aqueous phase into the solid and from the solid into aqueous phase. We calculated that 5-20% of structural Fe in clay minerals NAu-1, NAu-2, and SWa-1 exchanged with aqueous Fe(II), which significantly exceeds the Fe atom layer exposed directly to solution. Calculations based on electron-hopping rates in nontronite suggest that the bulk conduction mechanism previously demonstrated for hematite1 and suggested as an explanation for the significant Fe atom exchange observed in goethite2 may be a plausible mechanism for Fe atom exchange in Fe-bearing clay minerals. Our finding of 5-20% Fe atom exchange in clay minerals indicates that we need to rethink how Fe mobility affects the macroscopic properties of Fe-bearing phyllosilicates and its role in Fe biogeochemical cycling, as well as its use in a variety of engineered applications, such as landfill liners and nuclear repositories.

  10. 25 CFR 225.33 - Assignment of minerals agreements.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Assignment of minerals agreements. 225.33 Section 225.33 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS OIL AND GAS, GEOTHERMAL, AND SOLID MINERALS AGREEMENTS Minerals Agreements § 225.33 Assignment of minerals agreements. An...

  11. 30 CFR 256.80 - Leases of other minerals.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Leases of other minerals. 256.80 Section 256.80 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE LEASING OF SULPHUR OR OIL AND GAS IN THE OUTER CONTINENTAL SHELF Section 6 Leases § 256.80 Leases of other minerals. The...

  12. 30 CFR 48.26 - Experienced miner training.

    Science.gov (United States)

    2010-07-01

    ... the physical and health hazards of chemicals in the miner's work area, the protective measures a miner... occurred during the miner's absence and that could adversely affect the miner's health or safety. (1) A... Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING...

  13. Mineral extraction and transport device

    Energy Technology Data Exchange (ETDEWEB)

    Plaga, K.

    1991-08-21

    A device for the extraction and transport of stratified mineral deposits notably coal, having a transport run with lengths of transport troughing, an extraction run with lengths of extraction troughing, and a power-driven traction chain guided round return devices and carrying extraction bodies together with optional transport units. The transport and extraction troughing have guide members on which the extraction bodies and the transport units are guided with the aid of guide formations. Each extraction body consists of a headpiece having two laterally protruding guide formations, and an endpiece having two laterally protruding guide formations and a centrepiece. The headpiece and the endpiece are swivellably linked to the centrepiece through an axis running substantially at right angles to the traction axis of the traction chain and substantially at right angles to the floor of the lengths of transport troughing in the transport run. The centrepiece has an additional articulation about an axis substantially orthogonal to the swivel axis of the headpiece and the endpiece. Guide members are additionally provided in the vicinity of the return devices whereby the guide formations on each headpiece and endpiece receive continued guidance.

  14. Mineral oils, tars. [British patent

    Energy Technology Data Exchange (ETDEWEB)

    O' Brien, A M; Handmarch, E

    1933-08-11

    Hydrocarbon materials such as mineral oils and tars from coal, shale, lignite, or peat are freed from phenols and like oxy-bodies by heating under pressure in a closed vessel to a temperature and for a time sufficient to effect reduction of the oxy-bodies, and then removing the water formed by the reaction. 350/sup 0/ to 400/sup 0/C. for 30 to 60 minutes is suitable. Any wax-like constituents are converted to liquids of lower viscosity and settling point. The product may be fractionated to give light oils and a residue of aviation Diesel fuel. In an example, oil from the low-temperature distillation of coal and having a tar acid content of 30 per cent is treated in a tubular converter at 380/sup 0/C. and 400 lb. per sq. in for 40 min., and the benzine toluol, and xylol distilled; the residue has a tar acid content of only 7.6 per cent.

  15. Printing nature: Unraveling the role of nacre's mineral bridges.

    Science.gov (United States)

    Gu, Grace X; Libonati, Flavia; Wettermark, Susan D; Buehler, Markus J

    2017-12-01

    Creating materials with strength and toughness has been a long-sought goal. Conventional engineering materials often face a trade-off between strength and toughness, prompting researchers seeking to overcome these limitations to explore more sophisticated materials, such as composites. This paradigm shift in material design is spurred by nature, which exhibits a plethora of heterogeneous materials that offer outstanding material properties, and many natural materials are widely regarded as examples of high-performing hybrid materials. A classic example is nacre, also known as mother-of-pearl, which boasts a combination of high stiffness, strength, and fracture toughness. Various microstructural features contribute to the toughness of nacre, including mineral bridges (MBs), nano-asperities, and waviness of the constituent platelets. Recent research in biomimicry suggests that MBs contribute to the high strength and toughness observed in nacre and nacre-inspired materials. However, previous work in this area did not allow for complete control over the length scale of the bridges and had limitations on the volume fraction of mineral content. In this work, we present a systematic investigation elucidating the effects of structural parameters, such as volume fraction of mineral phase and density of MBs, on the mechanical response of nacre-inspired additive manufactured composites. Our results demonstrate that it is possible to tune the composite properties by tuning sizes and content of structural features (e.g. MBs and mineral content) in a heterogeneous material. Looking forward, this systematic approach enables materials-by-design of complex architectures to tackle demanding engineering challenges in the future. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Crystal-Chemical Analysis Martian Minerals in Gale Crater

    Science.gov (United States)

    Morrison, S. M.; Downs, R. T.; Blake, D. F.; Bish, D. L.; Ming, D. W.; Morris, R. V.; Yen, A. S.; Chipera, S. J.; Treiman, A. H.; Vaniman, D. T.; hide

    2015-01-01

    The CheMin instrument on the Mars Science Laboratory rover Curiosity performed X-ray diffraction analyses on scooped soil at Rocknest and on drilled rock fines at Yellowknife Bay (John Klein and Cumberland samples), The Kimberley (Windjana sample), and Pahrump (Confidence Hills sample) in Gale crater, Mars. Samples were analyzed with the Rietveld method to determine the unit-cell parameters and abundance of each observed crystalline phase. Unit-cell parameters were used to estimate compositions of the major crystalline phases using crystal-chemical techniques. These phases include olivine, plagioclase and clinopyroxene minerals. Comparison of the CheMin sample unit-cell parameters with those in the literature provides an estimate of the chemical compositions of the major crystalline phases. Preliminary unit-cell parameters, abundances and compositions of crystalline phases found in Rocknest and Yellowknife Bay samples were reported in. Further instrument calibration, development of 2D-to- 1D pattern conversion corrections, and refinement of corrected data allows presentation of improved compositions for the above samples.

  17. Analysis of minerals from Antarctica

    International Nuclear Information System (INIS)

    Sitek, J.; Dekan, J.; Sedlackova, K.; Novak, P.; Gokhman, A.

    2016-01-01

    In this work, Moessbauer spectroscopy and X-ray diffraction was used for phase analysis of iron-bearing compounds with the aim to identify magnetic and non-magnetic fractions in the selected rocks of the Western part of Antarctic Peninsula from different localities. The obtained data should elucidate the directional dependence of the composition, structure, volume fraction and size of magnetic inclusions in the rocks from the Western part of Antarctic Peninsula. (authors)

  18. Novel phosphate-grafted ePTFE copolymers for optimum in vitro mineralization

    International Nuclear Information System (INIS)

    Wentrup-Byrne, Edeline; Suzuki, Shuko; Groendahl, Lisbeth; Suwanasilp, Juthakarn Jessica

    2010-01-01

    Surface modification via graft copolymerization is an attractive method for optimizing polymers used in biomedical applications. We developed a novel method using a mixed solvent system (either water and dichloromethane (DCM) or water, methanol and DCM) consisting of two solvent phases for grafting 2-(methacryloyloxy)ethyl phosphate onto expanded polytetrafluoroethylene (ePTFE). This new method resulted in the fabrication of grafted membranes with greater grafting extents (GEs) (as evaluated from x-ray photoelectron spectroscopy (XPS)) in the organic phase than those obtained when grafting was carried out in a single phase. It also made it possible to graft in the aqueous phase, a process that is otherwise inhibited by the concomitant formation of large amounts of highly crystalline homopolymer. Thorough characterization of the grafted membranes using gravimetric, XPS and attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) not only permitted evaluation of the grafting outcomes but also made it possible to analyze their dependence on monomer concentration and solvent composition. A selection of membranes was tested for their in vitro mineralization capacity using simulated body fluid. It was found that an 'ideal' mineralization outcome, i.e. a uniform coating of carbonated hydroxyapatite (cHAP) formed on the sample grafted in the aqueous phase of the water/DCM two-phase solvent system. A detailed discussion bringing together these results, as well as results from a series of earlier studies, allows conclusions regarding polymer chemistry and the topology necessary for cHAP mineralization.

  19. Petrography, metasomatism and mineralization of uranium and other radioactive minerals in the Narigan Area (Central Iran) Islamic Republic of Iran

    International Nuclear Information System (INIS)

    Fazeli, A.; Azizaliabad, M.; Iranmanesh, J.

    2014-01-01

    , phyllic and propylitic alteration zones. Ni shows an adaptable increase in phlogopite-magnetite zone and hornfelsic, propylitic alterations. Uranium mineralization in this study area, is comparable with two uranium ore types: plutogenic and volcanogenic. These matters were indicated by various alteration types that observed in Narigan area. In plutonic-type uranium mineralization, uranium is present in sulphide-uraninite and arsenideuraninite types. In the Narigan Zone, the presence of sulphide is seen in minerals like pyrite, calcopyrite, and sphalerite. Existence of arsenide is indicated by a few minerals such as: arsenopyrite and glokodot and also relative enrichment of elements like Ag, Bi, Co, Ni and U in some veins. These are signatures for sulphide-uraninite and arsinide-uraninite mineralizing type. Presence of brannerite (davidite-branerite paragenesis) in thin sections is an index signature for volcanogenic uranium-titanium mineralizing type. The secondary titanium-bearing minerals are made by ilmenite and sphene alterations. Relative enrichment of elements like Cu, Mo, Ni, Pb and Zn is made by the effect of high temperature potassic phase on the Narigan volcanogenic rocks. With the consideration of sub-volcanic nature of Narigan zone, metasomatic processes and related hydrothermal phases have been active in shallow environment. On the basis of Bardina and Popov classification the different metasomatic processes at Narigan area have happened in basic to acidic circumstance, with pH 3-9 under temperature range of 150-600°C. (author)

  20. Improved accuracy of cortical bone mineralization measured by polychromatic microcomputed tomography using a novel high mineral density composite calibration phantom

    International Nuclear Information System (INIS)

    Deuerling, Justin M.; Rudy, David J.; Niebur, Glen L.; Roeder, Ryan K.

    2010-01-01

    Purpose: Microcomputed tomography (micro-CT) is increasingly used as a nondestructive alternative to ashing for measuring bone mineral content. Phantoms are utilized to calibrate the measured x-ray attenuation to discrete levels of mineral density, typically including levels up to 1000 mg HA/cm 3 , which encompasses levels of bone mineral density (BMD) observed in trabecular bone. However, levels of BMD observed in cortical bone and levels of tissue mineral density (TMD) in both cortical and trabecular bone typically exceed 1000 mg HA/cm 3 , requiring extrapolation of the calibration regression, which may result in error. Therefore, the objectives of this study were to investigate (1) the relationship between x-ray attenuation and an expanded range of hydroxyapatite (HA) density in a less attenuating polymer matrix and (2) the effects of the calibration on the accuracy of subsequent measurements of mineralization in human cortical bone specimens. Methods: A novel HA-polymer composite phantom was prepared comprising a less attenuating polymer phase (polyethylene) and an expanded range of HA density (0-1860 mg HA/cm 3 ) inclusive of characteristic levels of BMD in cortical bone or TMD in cortical and trabecular bone. The BMD and TMD of cortical bone specimens measured using the new HA-polymer calibration phantom were compared to measurements using a conventional HA-polymer phantom comprising 0-800 mg HA/cm 3 and the corresponding ash density measurements on the same specimens. Results: The HA-polymer composite phantom exhibited a nonlinear relationship between x-ray attenuation and HA density, rather than the linear relationship typically employed a priori, and obviated the need for extrapolation, when calibrating the measured x-ray attenuation to high levels of mineral density. The BMD and TMD of cortical bone specimens measured using the conventional phantom was significantly lower than the measured ash density by 19% (p<0.001, ANCOVA) and 33% (p<0.05, Tukey's HSD

  1. Radionuclide release from simulated waste material after biogeochemical leaching of uraniferous mineral samples

    International Nuclear Information System (INIS)

    Williamson, Aimee Lynn; Caron, François; Spiers, Graeme

    2014-01-01

    Biogeochemical mineral dissolution is a promising method for the released of metals in low-grade host mineralization that contain sulphidic minerals. The application of biogeochemical mineral dissolution to engineered leach heap piles in the Elliot Lake region may be considered as a promising passive technology for the economic recovery of low grade Uranium-bearing ores. In the current investigation, the decrease of radiological activity of uraniferous mineral material after biogeochemical mineral dissolution is quantified by gamma spectroscopy and compared to the results from digestion/ICP-MS analysis of the ore materials to determine if gamma spectroscopy is a simple, viable alternative quantification method for heavy nuclides. The potential release of Uranium (U) and Radium-226 ( 226 Ra) to the aqueous environment from samples that have been treated to represent various stages of leaching and passive closure processes are assessed. Dissolution of U from the solid phase has occurred during biogeochemical mineral dissolution in the presence of Acidithiobacillus ferrooxidans, with gamma spectroscopy indicating an 84% decrease in Uranium-235 ( 235 U) content, a value in accordance with the data obtained by dissolution chemistry. Gamma spectroscopy data indicate that only 30% of the 226 Ra was removed during the biogeochemical mineral dissolution. Chemical inhibition and passivation treatments of waste materials following the biogeochemical mineral dissolution offer greater protection against residual U and 226 Ra leaching. Pacified samples resist the release of 226 Ra contained in the mineral phase and may offer more protection to the aqueous environment for the long term, compared to untreated or inhibited residues, and should be taken into account for future decommissioning. - Highlights: • Gamma counting showed an 84% decrease in 235 U after biogeochemical mineral leaching. • Chemical digestion/ICP-MS analysis also showed an 84% decrease in total U. • Over

  2. Mill tailings based composites as paste backfill in mines of U-bearing dolomitic limestone ore

    Directory of Open Access Journals (Sweden)

    Sandeep Panchal

    2018-04-01

    Full Text Available This paper elaborates on the development of paste backfill using mill tailings generated during the processing of a uranium ore deposit hosted in dolomitic limestone. The tailings have been characterized in terms of the physical, chemical and mineralogical properties. Time-dependent rheological behaviors and geotechnical properties of cemented paste backfill (CPB are also determined. The studies show that the mill tailing has the potential to form paste and the CPB has adequate strength to provide support to mine pillars, roofs, and walls. Keywords: Mining engineering, Uranium ore deposit, Tailings, Cemented paste backfill (CPB, Rheology, Compressive strength

  3. Geochemical correlations between uranium and other components in U-bearing formations of Ogcheon belt

    International Nuclear Information System (INIS)

    Lee, M.S.; Chon, H.T.

    1980-01-01

    Some components in uranium-bearing formations which consist mainly of black shale, slate and low grade coal-bearing formation of Ogcheon Belt were processed statistically in order to find out the geochemical correlations with uranium. Geochemical enrichment of uranium, vanadium and molybdenum in low grade coal-bearing formations and surrounding rocks is remarkable in the studied area. Geochemical correlation coefficient of uranium and molybdenum in the rocks displays about 0.6 and that of uranium and fixed carbon about 0.4. Uranium and vanadium in uranium-bearing low grade coals denote very high correlation with fixed carbon, which is considered to be responsible for enrichment of metallic elements, especially molybdenum. Close geochemical correlation of uranium-molybdenum couple in the rocks can be applied as a competent exploration guide to low grade uranium deposits of this area. (author)

  4. Pirm wastes: permanent isolation in rock-forming minerals

    International Nuclear Information System (INIS)

    Smyth, J.R.; Vidale, R.J.; Charles, R.W.

    1977-01-01

    The most practical system for permanent isolation of radioactive wastes in granitic and pelitic environments may be one which specifically tailors the waste form to the environment. This is true because if recrystallization of the waste form takes place within the half-lives of the hazardous radionuclides, it is likely to be the rate-controlling step for release of these nuclides to the ground-water system. The object of the proposed waste-form research at Los Alamos Scintific Laboratory (LASL) is to define a phase assemblage which will minimize chemical reaction with natural fluids in a granitic or pelitic environment. All natural granites contain trace amounts of all fission product elements (except Tc) and many contain minor amounts of these elements as major components of certain accessory phases. Observation of the geochemistry of fission-product elements has led to the identification of the natural minerals as target phases for research. A proposal is made to experimentally determine the amounts of fission product elements which can stably be incorporated into the phases listed below and to determine the leachability of the assemblage this produced using fluids typical of the proposed environments at the Nevada Test Site. This approach to waste isolation satisfies the following requirements: (1) It minimizes chemical reaction with the environment (i.e., recrystallization) which is likely to be the rate-controlling step for release of radionuclides to groundwater; (2) Waste loading (hence temperature) can be easily varied by dilution with material mined from the disposal site; (3) No physical container is required; (4) No maintenance is required (permanent); (5) The environment acts as a containment buffer. It is proposed that such wastes be termed PIRM wastes, for Permanent Isolation in Rock-forming Minerals

  5. Holocene paleoclimatic variation in the Schirmacher Oasis, East Antarctica: A mineral magnetic approach

    Science.gov (United States)

    Phartiyal, Binita

    2014-12-01

    An analysis of remanent magnetism and radiocarbon ages in the dry lacustrine/sediment fills of the Schirmacher Oasis (SO) in East Antarctica was conducted to reconstruct past climatic condition. The statistically run mineral magnetic data on paleontological statistics software package (multivariate cluster analysis) placed on accelerator mass spectrometer radiocarbon chronology of the three sediment sections, trace 6 phases of climatic fluctuation between 13 and 3 ka, (Phases 1, 3 and 5 represent cold periods while Phases 2, 4, and 6 represent warm periods). One short warm period (Phase 2, ca. 12.5 ka) occurred in the late Pleistocene, and two marked warm periods (Phase 4, 11-8.7 ka; Phase 6, 4.4-3 ka) occurred in the Holocene. High magnetic susceptibility (χ), saturation isothermal remanent magnetism (SIRM), and soft isothermal remanent magnetism (soft IRM) values correspond to colder periods and low values reflect comparatively warmer lacustrine phases. Holocene Optima (Phase 4) and Mid Holocene Hypsithermal (Phase 6) are distinguished by decreased values of concentrations dependent parameters. Remanence is preserved in the low-coercive minerals. Heavy metals in the sediments include, Fe, Rb, Zn, Mo, Co, Pb, Mn, Cu, and As in order of decreasing abundance.

  6. Mineralenconcentraten uit dierlijke mest : monitoring in het kader van de pilot mineralenconcentraten = Mineral concentrates from animal slurry : monitoring of the pilot production plants

    NARCIS (Netherlands)

    Hoeksma, P.; Buisonjé, de F.E.; Ehlert, P.A.I.; Horrevorts, J.H.

    2011-01-01

    Processing of animal manure is considered as an opportunity to reduce the pressure on the manure market in the Netherlands. One of the options is to separate the slurry and to use the mineral concentrate, that is produced from the liquid phase by reverse osmosis, as a substitute for mineral

  7. Mineral facilities of Northern and Central Eurasia

    Science.gov (United States)

    Baker, Michael S.; Elias, Nurudeen; Guzman, Eric; Soto-Viruet, Yadira

    2010-01-01

    This map displays almost 900 records of mineral facilities within the countries that formerly constituted the Union of Soviet Socialist Republics (USSR). Each record represents one commodity and one facility type at a single geographic location. Facility types include mines, oil and gas fields, and plants, such as refineries, smelters, and mills. Common commodities of interest include aluminum, cement, coal, copper, gold, iron and steel, lead, nickel, petroleum, salt, silver, and zinc. Records include attributes, such as commodity, country, location, company name, facility type and capacity (if applicable), and latitude and longitude geographical coordinates (in both degrees-minutes-seconds and decimal degrees). The data shown on this map and in table 1 were compiled from multiple sources, including (1) the most recently available data from the U.S. Geological Survey (USGS) Minerals Yearbook (Europe and Central Eurasia volume), (2) mineral statistics and information from the USGS Minerals Information Web site (http://minerals.usgs.gov/minerals/pubs/country/europe.html), and (3) data collected by the USGS minerals information country specialists from sources, such as statistical publications of individual countries, annual reports and press releases of operating companies, and trade journals. Data reflect the most recent published table of industry structure for each country at the time of this publication. Additional information is available from the country specialists listed in table 2

  8. Mineral facilities of Asia and the Pacific

    Science.gov (United States)

    Baker, Michael S.; Elias, Nurudeen; Guzman, Eric; Soto-Viruet, Yadira

    2010-01-01

    This map displays over 1,500 records of mineral facilities throughout the continent of Asia and the countries of the Pacific Ocean. Each record represents one commodity and one facility type at a single geographic location. Facility types include mines, oil and gas fields, and plants, such as refineries, smelters, and mills. Common commodities of interest include aluminum, cement, coal, copper, gold, iron and steel, lead, nickel, petroleum, salt, silver, and zinc. Records include attributes, such as commodity, country, location, company name, facility type and capacity (if applicable), and latitude and longitude geographical coordinates (in both degrees-minutes-seconds and decimal degrees). The data shown on this map and in table 1 were compiled from multiple sources, including (1) the 2008 U.S. Geological Survey Minerals Yearbook (Asia and the Pacific volume), (2) minerals statistics and information from the U.S. Geological Survey Minerals Information Web site (http://minerals.usgs.gov/minerals/), and (3) data collected by U.S. Geological Survey minerals information country specialists. Other sources include statistical publications of individual countries, annual reports and press releases of operating companies, and trade journals. Due to the sensitivity of some energy commodity data, the quality of these data should be evaluated on a country-by-country basis. Additional information is available from the country specialists listed in table 2.

  9. Heavy mineral concentration from oil sand tailings

    Energy Technology Data Exchange (ETDEWEB)

    Chachula, F.; Erasmus, N. [Titanium Corp. Inc., Regina, SK (Canada)

    2008-07-01

    This presentation described a unique technique to recover heavy minerals contained in the froth treatment tailings produced by oil sand mining extraction operations in Fort McMurray, Alberta. In an effort to process waste material into valuable products, Titanium Corporation is developing technology to recover heavy minerals, primarily zircon, and a portion of bitumen contained in the final stage of bitumen processing. The process technology is being developed to apply to all mined oil sands operations in the Fort McMurray region. In 2004, Titanium Corporation commissioned a pilot research facility at the Saskatchewan Research Council to test dry oil sands tailings. In 2005, a bulk sampling pilot plant was connected to the fresh oil sands tailings pipeline on-site in Fort McMurray, where washed sands containing heavy minerals were processed at a pilot facility. The mineral content in both deposited tailings and fresh pipeline tailings was assessed. Analysis of fresh tailings on a daily basis identified a constant proportion of zircon and higher levels of associated bitumen compared with the material in the deposited tailings. The process flow sheet design was then modified to remove bitumen from the heavy minerals and concentrate the minerals. A newly modified flotation process was shown to be a viable processing route to recover the heavy minerals from froth treatment tailings. 8 refs., 9 tabs., 12 figs.

  10. Minerals in thalassaemia major patients: An overview.

    Science.gov (United States)

    Ozturk, Zeynep; Genc, Gizem Esra; Gumuslu, Saadet

    2017-05-01

    Thalassaemia major (TM) is a hereditary blood disease characterised by reduced or absent production of beta globin chains. Erythrocyte transfusions are given to raise the haemoglobin level in patients with thalassaemia major. However, transfusions have been related to increased risk of iron overload and tissue damage related to excess iron. Both elevated oxidative stress due to iron overload and increased hemolysis lead to over utilisation of minerals required for antioxidant enzymes activities. Iron chelators have been used to prevent iron overload in thalassaemia major patients, but these chelators have the possibility of removing minerals from the body. Thalassaemia patients are more at risk for mineral deficiency because of increased oxidative stress and iron chelation therapies. Growth and maturational delay, cardiomyopathy, endocrinopathies and osteoporosis are the complications of thalassaemia. Minerals may play a particular role to prevent these complications. In the current review, we provide an overview of minerals including zinc (Zn), copper (Cu), selenium (Se), magnesium (Mg) and calcium (Ca) in thalassaemia major patients. We, also, underline that some complications of thalassaemia can be caused by an increased need for minerals or lack of the minerals. Copyright © 2017 Elsevier GmbH. All rights reserved.

  11. Rn daughter exposure to U miners

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, B L

    1982-04-01

    Radon exposures to U.S. uranium miners under present conditions average about 1.3 WLM per year approximately or equal to 60 WLM per full working lifetime. This is intermediate between the lowest exposures for which there have been excess lung cancers reported among U.S. miners (120-240 WLM) and average environmental radon exposures (16 WLM), so models based on these two situations are used to estimate expected effects on present uranium miners. In Model A, the loss of life expectancy is 45 days, the SMR (standardized mortality ratio) for lung cancer is 1.10, and the SMR for all causes between ages 18 and 65 is 1.013. In Model B these are 10 days, 1.03 and 1.002 respectively. It is shown that the radon exposures to miners are similar to those to millions of Americans from environmental exposure, and that miner health risks are comparable to those of other radiation workers. Their lung cancer risk from radon is 7-50 times less than their job-related accident mortality risk, and represents 0.7-4% of their total risk in mining. Miners suffer from many diseases with SMR very much larger than that for radon-induced lung cancer, and there are many other occupations and industries with far higher SMR for lung cancer than that from radon exposure to miners.

  12. Marketing mix of chosen Slovak mineral water

    Directory of Open Access Journals (Sweden)

    Juhanová Silvia

    2001-09-01

    Full Text Available Considering its small area, Slovakia abounds in many sources of mineral waters and a considerable amount of them can be used for the commercial utilization. STN 86 8000 divides mineral waters in the natural mineral waters, natural mineral table waters and the natural mineral healing waters. Natural mineral water is, after the present norm, in effect water, which rises from natural trapped sources. This type of water contains more than 1 gram of dissolved substances or 1 gram of dissolved CO 2 in 1 litter. Natural mineral table water is water that, with its chemical composition as well as its physical and sensorial attributes is suitable as a refresher. It contains at least 1 gram of melted CO2 and up to 6 grams of dissolved illiquid substances in 1 litter. The mentioned substances are not characterised by any marked pharmacological effect. Natural mineral healing water is water, which with an eye to its chemical composition and physical properties, have a scientifically demonstrable effects to the human health and it is generally used for healing purposes. In the present contribution, an attention is orientated to the occurrence of listed types of waters in Slovakia, in connection with geological conditions of their circulation and accumulation and especially with possibilities of their use on the Slovak buyer’s market.The marketing mix is a complex of information, which can be regulated. Firms accumulate this information to satisfy a customer. Marketing mix of mineral waters includes information about four variables: product (characteristics of product, quality, packing, design..., prices, advertisement, distribution (the way how to get product to customer. Data listed in the contribution come from the sectional market research, which was performed between December 1st and December 22nd 2000 in twenty groceries in

  13. Moessbauer and XRD Comparative Study of Host Rock and Iron Rich Mineral Samples from Paz del Rio Iron Ore Mineral Mine in Colombia

    International Nuclear Information System (INIS)

    Fajardo, M.; Perez Alcazar, G. A.; Moreira, A. M.; Speziali, N. L.

    2004-01-01

    A comparative study between the host rock and the iron rich mineral samples from the Paz del Rio iron ore mineral mine in Colombia was performed using X-ray diffraction and Moessbauer spectroscopy. Diffraction results of the iron rich mineral sample show that goethite, hematite, quartz, kaolinite and siderite are the main phases, and that a small amount of illite is also present. By Moessbauer spectroscopy at room temperature (RT) the presence of all the above mentioned phases was detected except quartz as well as an additional presence of small amount of biotite. The goethite, which appears as four sextets with hyperfine fields of 33.5, 30.5, 27.5 and 18.5 T, respectively, is the majority phase. This result shows the different grades of formation of this oxyhydroxide. The Moessbauer spectrum of this sample at 80 K presents the same phases obtained at RT without any superparamagnetic effect. In this case the goethite appears as two sextets. Diffraction results of the host rock sample show a large amount of quartz and kaolinite and small amounts of illite and biotite, whereas by Moessbauer spectroscopy illite, kaolinite and biotite were detected.

  14. Fractal analysis of sulphidic mineral

    Directory of Open Access Journals (Sweden)

    Miklúšová Viera

    2002-03-01

    Full Text Available In this paper, the application of fractal theory in the characterization of fragmented surfaces, as well as the mass-size distributions are discussed. The investigated mineral-chalcopyrite of Slovak provenience is characterised after particle size reduction processes-crushing and grinding. The problem how the different size reduction methods influence the surface irregularities of obtained particles is solved. Mandelbrot (1983, introducing the fractal geometry, offered a new way of characterization of surface irregularities by the fractal dimension. The determination of the surface fractal dimension DS consists in measuring the specific surface by the BET method in several fractions into which the comminuted chalcopyrite is sieved. This investigation shows that the specific surface of individual fractions were higher for the crushed sample than for the short-term (3 min ground sample. The surface fractal dimension can give an information about the adsorption sites accessible to molecules of nitrogen and according to this, the value of the fractal dimension is higher for crushed sample.The effect of comminution processes on the mass distribution of particles crushed and ground in air as well as in polar liquids is also discussed. The estimation of fractal dimensions of particles mass distribution is done on the assumption that the particle size distribution is described by the power-law (1. The value of fractal dimension for the mass distribution in the crushed sample is lower than in the sample ground in air, because it is influenced by the energy required for comminution.The sample of chalcopyrite was ground (10min in ethanol and i-butanol [which according to Ikazaki (1991] are characterized by the parameter µ /V, where µ is its dipole moment and V is the molecular volume. The values of µ /V for the used polar liquids are of the same order. That is why the expressive differences in particle size distributions as well as in the values of

  15. Rheology of unstable mineral emulsions

    Directory of Open Access Journals (Sweden)

    Sokolović Dunja S.

    2013-01-01

    Full Text Available In this paper, the rheology of mineral oils and their unstable water emulsion were investigated. The oil samples were domestic crude oil UA, its fractions UA1, UA4 and blend semi-product UP1, while the concentration of oil in water emulsions was in the range from 1 up to 30%. The results were analyzed based on shear stress. The oil samples UA, UA1 and UP1 are Newtonian fluids, while UA4 is pseudoplastic fluid. The samples UA and UA4 show higher value of shear stress (83.75 Pa, 297 Pa, then other two samples UA1 and UP1 (18.41 Pa, 17.52 Pa. Rheology of investigated oils due to its complex chemical composition should be analyzed as a simultaneous effect of all their components. Therefore, structural composition of the oils was determined, namely content of paraffins, naphthenes, aromatics and asphaltenes. All samples contain paraffins, naphthenes and aromatics but only oils UA and UA4 contain asphaltenes as well. All investigated emulsions except 30% EUA4 are Newtonian fluids. The EUA4 30% emulsion shows pseudoplastic behaviour, and it is the only 30% emulsion among investigated ones that achieves lower shear stress then its oil. The characteristics of oil samples that could have an influence on their properties and their emulsion rheology, were determined. These characteristics are: neutralization number, interfacial tension, dielectric constant, and emulsivity. Oil samples UA and UA4 have significantly higher values of neutralization number, dielectric constants, and emulsivity. The sample UA has the lowest value of interface tension and the greatest emulsivity, indicating that this oil, among all investigated, has the highest preference for building emulsion. This could be the reason why 20% and 30% emulsions of the oil UA achieve the highest shear stress among all investigated emulsions.

  16. Radiotracer techniques in mineral processing

    International Nuclear Information System (INIS)

    Przewlocki, K.

    1991-01-01

    The value of the smelter metal content in currently exploited polymetallic ores mostly does not exceed 2%. Before metallurgical treatment, ore must pass through the concentration process. The benefication process usually starts from the comminution of excavated material and terminates at the flotation and drying of the concentrate. These operations consume vast quantities of energy. To be economically justified, the process requires optimization and, if possible, automatic control. Radioactive tracers were found to be useful in the identification of particular technological subsystems and their subsequent optimization. A great deal of experience has been gathered in this field so far. The industrial radiotracer test (RTT) is carried out using very sensitive multidetector recording systems which have digital data acquisition capabilities. The optimization strategy consists of periodically adjusting technological process and set points of controlled variables according to certain improvement procedures. If computer facilities are available, data interpretation and calibration of the mathematical models describing the technical process itself can be performed on the spot. This significantly accelerates the whole procedure as RTT may be repeated for particular system configurations. The procedure of plant optimization by means of RTT is illustrated in the paper using the example of the copper ore enrichment process, assuming that it is representative of the whole mineral industry. Identification by RTT of the three main operations involved in the ore enrichment process, such as comminution, flotation and granular classification, is discussed in detail as particular case studies. In reference to this, it is also shown how the technological process can be adjusted to be most efficient. (author). 14 refs, 7 figs

  17. Airborne Geophysical/Geological Mineral Inventory CIP Program

    National Research Council Canada - National Science Library

    1999-01-01

    The Airborne-Geophysical/Geological Mineral Inventory project is a special multi-year investment to expand the knowledge base of Alaska's mineral resources and catalyze private-sector mineral development...

  18. Uranium mineralization of migmatite in southern China

    Energy Technology Data Exchange (ETDEWEB)

    Feng, Mingyue

    1987-09-01

    The uranium mineralization occurs in migmatite in the form of disseminated uraninite is a new type found in southern China. According to the forms of uraninite existence in orebodies, it can be divided into primary and reworked subtypes. The principal uranium mineral in the deposits of primary subtype is uraninite, but those in reworked subtype are pitchblende and relict uraninite. The formation of uranium mineralization is considered as a result of remobilization, migration and local concentration caused by preferential melting of the uranium-rich strata.

  19. Uranium mineralization of migmatite in southern China

    International Nuclear Information System (INIS)

    Feng Mingyue.

    1987-01-01

    The uranium mineralization occurs in migmatite in the form of disseminated uraninite is a new type found in southern China. According to the forms of uraninite existence in orebodies, it can be divided into primary and reworked subtypes. The principal uranium mineral in the deposits of primary subtype is uraninite, but those in reworked subtype are pitchblende and relict uraninite. The formation of uranium mineralization is considered as a result of remobilization, migration and local concentration caused by preferential melting of the uranium-rich strata

  20. Uranyl adsorption at clay mineral surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Roesch, N. [Technische Univ. Muenchen (Germany). Fachgebiet Theoretische Chemie

    2016-11-01

    This first systematic survey of actinide adsorption at complex clay mineral surfaces, which provided new insights at the atomic level, is currently being extended to neptunyl NpO{sub 2}{sup +} and more complex minerals, like iron-substituted phyllosilicates. In this way we examine if the concepts developed so far can be applied more generally to support the interpretation of pertinent experiments. A further facet of these studies is to account also for the dynamic nature of the mineral/water interface by means of exemplary dynamic simulations.

  1. Chromosomal aberrations in ore miners of Slovakia

    International Nuclear Information System (INIS)

    Beno, M.; Vladar, M.; Nikodemova, D.; Vicanova, M.; Durcik, M.

    1998-01-01

    A pilot study was performed in which the incidence of chromosomal aberrations in lymphocytes of miners in ore mines located in Central Slovakia was monitored and related to lifetime underground radon exposure and to lifetime smoking. The conclusions drawn from the results of the study were as follows: the counts of chromosomal aberrations in lymphocytes of miners were significantly higher than in an age matched control group of white-collar staff; the higher counts of chromosomal aberrations could be ascribed to underground exposure of miners and to smoking; a dependence of chromosomal aberration counts on the exposure to radon could not be assessed. (A.K.)

  2. Characterization of minerals, metals and materials

    CERN Document Server

    Hwang, Jiann-Yang; Bai, Chengguang; Carpenter, John; Cai, Mingdong; Firrao, Donato; Kim, Byoung-Gon

    2012-01-01

    This state-of-the-art reference contains chapters on all aspects of the characterization of minerals, metals, and materials. The title presents papers from one of the largest yearly gatherings of materials scientists in the world and thoroughly discusses the characterization of minerals, metals, and materials The scope includes current industrial applications and research and developments in the following areas:  Characterization of Ferrous Metals Characterization of Non-Ferrous Materials Characterization of Minerals and Ceramics Character

  3. Sea urchin tooth mineralization: Calcite present early in the aboral plumula

    Science.gov (United States)

    Stock, Stuart R.; Veis, Arthur; Xiao, Xianghui; Almer, Jonathan D.; Dorvee, Jason R.

    2012-01-01

    In both vertebrate bone, containing carbonated hydroxyapatite as the mineral phase, and in invertebrate hard tissue comprised of calcium carbonate, a popular view is that the mineral phase develops from a long-lived amorphous precursor which later transforms into crystal form. Important questions linked to this popular view are: When and where is the crystallized material formed, and is amorphous solid added subsequently to the crystalline substrate? Sea urchin teeth, in which the earliest mineral forms within isolated compartments, in a time and position dependent manner, allow direct investigation of the timing of crystallization of the calcite primary plates. Living teeth of the sea urchin Lytechinus variegatus, in their native coelomic fluid, were examined by high-energy synchrotron x-ray diffraction. The diffraction data show that calcite is present in the most aboral portions of the plumula, representing the very earliest stages of mineralization, and that this calcite has the same crystal orientation as in the more mature adoral portions of the same tooth. Raman spectroscopy of the aboral plumula confirms the initial primary plate mineral material is calcite and does not detect amorphous calcium carbonate; in the more mature adoral incisal flange, it does detect a broader calcite peak, consistent with two or more magnesium compositions. We hypothesize that some portion of each syncytial membrane in the plumula provides the information for nucleation of identically oriented calcite crystals that subsequently develop to form the complex geometry of the single crystal sea urchin tooth. PMID:22940703

  4. Sea urchin tooth mineralization: calcite present early in the aboral plumula.

    Science.gov (United States)

    Stock, Stuart R; Veis, Arthur; Xiao, Xianghui; Almer, Jonathan D; Dorvee, Jason R

    2012-11-01

    In both vertebrate bone, containing carbonated hydroxyapatite as the mineral phase, and in invertebrate hard tissue comprised of calcium carbonate, a popular view is that the mineral phase develops from a long-lived amorphous precursor which later transforms into crystal form. Important questions linked to this popular view are: when and where is the crystallized material formed, and is amorphous solid added subsequently to the crystalline substrate? Sea urchin teeth, in which the earliest mineral forms within isolated compartments, in a time and position dependent manner, allow direct investigation of the timing of crystallization of the calcite primary plates. Living teeth of the sea urchin Lytechinus variegatus, in their native coelomic fluid, were examined by high-energy synchrotron X-ray diffraction. The diffraction data show that calcite is present in the most aboral portions of the plumula, representing the very earliest stages of mineralization, and that this calcite has the same crystal orientation as in the more mature adoral portions of the same tooth. Raman spectroscopy of the aboral plumula confirms the initial primary plate mineral material is calcite and does not detect amorphous calcium carbonate; in the more mature adoral incisal flange, it does detect a broader calcite peak, consistent with two or more magnesium compositions. We hypothesize that some portion of each syncytial membrane in the plumula provides the information for nucleation of identically oriented calcite crystals that subsequently develop to form the complex geometry of the single crystal sea urchin tooth. Copyright © 2012 Elsevier Inc. All rights reserved.

  5. Paracrystalline Disorder from Phosphate Ion Orientation and Substitution in Synthetic Bone Mineral.

    Science.gov (United States)

    Marisa, Mary E; Zhou, Shiliang; Melot, Brent C; Peaslee, Graham F; Neilson, James R

    2016-12-05

    Hydroxyapatite is an inorganic mineral closely resembling the mineral phase in bone. However, as a biological mineral, it is highly disordered, and its composition and atomistic structure remain poorly understood. Here, synchrotron X-ray total scattering and pair distribution function analysis methods provide insight into the nature of atomistic disorder in a synthetic bone mineral analogue, chemically substituted hydroxyapatite. By varying the effective hydrolysis rate and/or carbonate concentration during growth of the mineral, compounds with varied degrees of paracrystallinity are prepared. From advanced simulations constrained by the experimental pair distribution function and density functional theory, the paracrystalline disorder prevalent in these materials appears to result from accommodation of carbonate in the lattice through random displacement of the phosphate groups. Though many substitution modalities are likely to occur in concert, the most predominant substitution places carbonate into the mirror plane of an ideal phosphate site. Understanding the mineralogical imperfections of a biologically analogous hydroxyapatite is important not only to potential bone grafting applications but also to biological mineralization processes themselves.

  6. Mineral identification in Colombian coals using Moessbauer spectroscopy and X-ray diffraction

    International Nuclear Information System (INIS)

    Fajardo, M.; Mojica, J.; Barraza, J.; Perez Alcazar, G.A.; Tabares, J.A.

    1999-01-01

    Minerals were identified in three Colombian coal samples from the Southwest of the country using Moessbauer spectroscopy and X-ray diffraction. Original and sink separated coal fractions of specific gravity 1.40 and 1.60 with particle size less than 600 μm were used in the study. Using Moessbauer spectroscopy, the minerals identified in the original coal samples were pyrite jarosite, ankerite, illite and ferrous sulfate, whereas by means of X-ray diffraction, minerals identified were kaolinite, quartz, pyrite, and jarosite. Differences in mineral composition were found in the original and sink separated fractions using both techniques. Moessbauer spectra show that the mineral phases in low concentrations such as illite, ankerite and ferrous sulfate do not always appear in the spectra of sink coals, despite of those minerals occurring in the original coal, due to the fact that they are associated with the organic matter and not liberated in the grinding process. X-ray results show that the peak intensity grows as the specific gravity is increased indicating that the density separation method could be an effective process to clean coal

  7. Modelling the mechanics of partially mineralized collagen fibrils, fibres and tissue

    Science.gov (United States)

    Liu, Yanxin; Thomopoulos, Stavros; Chen, Changqing; Birman, Victor; Buehler, Markus J.; Genin, Guy M.

    2014-01-01

    Progressive stiffening of collagen tissue by bioapatite mineral is important physiologically, but the details of this stiffening are uncertain. Unresolved questions about the details of the accommodation of bioapatite within and upon collagen's hierarchical structure have posed a central hurdle, but recent microscopy data resolve several major questions. These data suggest how collagen accommodates bioapatite at the lowest relevant hierarchical level (collagen fibrils), and suggest several possibilities for the progressive accommodation of bioapatite at higher hierarchical length scales (fibres and tissue). We developed approximations for the stiffening of collagen across spatial hierarchies based upon these data, and connected models across hierarchies levels to estimate mineralization-dependent tissue-level mechanics. In the five possible sequences of mineralization studied, percolation of the bioapatite phase proved to be an important determinant of the degree of stiffening by bioapatite. The models were applied to study one important instance of partially mineralized tissue, which occurs at the attachment of tendon to bone. All sequences of mineralization considered reproduced experimental observations of a region of tissue between tendon and bone that is more compliant than either tendon or bone, but the size and nature of this region depended strongly upon the sequence of mineralization. These models and observations have implications for engineered tissue scaffolds at the attachment of tendon to bone, bone development and graded biomimetic attachment of dissimilar hierarchical materials in general. PMID:24352669

  8. Dissolution and secondary mineral precipitation in basalts due to reactions with carbonic acid

    Science.gov (United States)

    Kanakiya, Shreya; Adam, Ludmila; Esteban, Lionel; Rowe, Michael C.; Shane, Phil

    2017-06-01

    One of the leading hydrothermal alteration processes in volcanic environments is when rock-forming minerals with high concentrations of iron, magnesium, and calcium react with CO2 and water to form carbonate minerals. This is used to the advantage of geologic sequestration of anthropogenic CO2. Here we experimentally investigate how mineral carbonation processes alter the rock microstructure due to CO2-water-rock interactions. In order to characterize these changes, CO2-water-rock alteration in Auckland Volcanic Field young basalts (less than 0.3 Ma) is studied before and after a 140 day reaction period. We investigate how whole core basalts with similar geochemistry but different porosity, permeability, pore geometry, and volcanic glass content alter due to CO2-water-rock reactions. Ankerite and aluminosilicate minerals precipitate as secondary phases in the pore space. However, rock dissolution mechanisms are found to dominate this secondary mineral precipitation resulting in an increase in porosity and decrease in rigidity of all samples. The basalt with the highest initial porosity and volcanic glass volume shows the most secondary mineral precipitation. At the same time, this sample exhibits the greatest increase in porosity and permeability, and a decrease in rock rigidity post reaction. For the measured samples, we observe a correlation between volcanic glass volume and rock porosity increase due to rock-fluid reactions. We believe this study can help understand the dynamic rock-fluid interactions when monitoring field scale CO2 sequestration projects in basalts.

  9. Mineral paragenesis on Mars: The roles of reactive surface area and diffusion.

    Science.gov (United States)

    Fairén, Alberto G; Gil-Lozano, Carolina; Uceda, Esther R; Losa-Adams, Elisabeth; Davila, Alfonso F; Gago-Duport, Luis

    2017-09-01

    Geochemical models of secondary mineral precipitation on Mars generally assume semiopen systems (open to the atmosphere but closed at the water-sediment interface) and equilibrium conditions. However, in natural multicomponent systems, the reactive surface area of primary minerals controls the dissolution rate and affects the precipitation sequences of secondary phases, and simultaneously, the transport of dissolved species may occur through the atmosphere-water and water-sediment interfaces. Here we present a suite of geochemical models designed to analyze the formation of secondary minerals in basaltic sediments on Mars, evaluating the role of (i) reactive surface areas and (ii) the transport of ions through a basalt sediment column. We consider fully open conditions, both to the atmosphere and to the sediment, and a kinetic approach for mineral dissolution and precipitation. Our models consider a geochemical scenario constituted by a basin (i.e., a shallow lake) where supersaturation is generated by evaporation/cooling and the starting point is a solution in equilibrium with basaltic sediments. Our results show that cation removal by diffusion, along with the input of atmospheric volatiles and the influence of the reactive surface area of primary minerals, plays a central role in the evolution of the secondary mineral sequences formed. We conclude that precipitation of evaporites finds more restrictions in basaltic sediments of small grain size than in basaltic sediments of greater grain size.

  10. Continuing Studies on Direct Aqueous Mineral Carbonation of CO{sub 2} Sequestration

    Energy Technology Data Exchange (ETDEWEB)

    O' Connor, W.K.; Dahlin, D.C.; Nilsen, D.N.; Gerdemann, S.J.; Rush, G.E.; Penner, L.R.; Walters, R.P.; Turner, P.C.

    2002-03-04

    Direct aqueous mineral carbonation has been investigated as a process to convert gaseous CO{sub 2} into a geologically stable, solid final form. The process utilizes a solution of sodium bicarbonate (NaHCO{sub 3}), sodium chloride (NaCl), and water, mixed with a mineral reactant, such as olivine (Mg{sub 2}SiO{sub 4}) or serpentine [Mg{sub 3}Si{sub 2}O{sub 5}(OH){sub 4}]. Carbon dioxide is dissolved into this slurry, by diffusion through the surface and gas dispersion within the aqueous phase. The process includes dissolution of the mineral and precipitation of the magnesium carbonate mineral magnesite (MgCO{sub 3}) in a single unit operation. Activation of the silicate minerals has been achieved by thermal and mechanical means, resulting in up to 80% stoichiometric conversion of the silicate to the carbonate within 30 minutes. Heat treatment of the serpentine, or attrition grinding of the olivine and/or serpentine, appear to activate the minerals by the generation of a non-crystalline phase. Successful conversion to the carbonate has been demonstrated at ambient temperature and relatively low (10 atm) partial pressure of CO{sub 2} (P{sub CO2}). However, optimum results have been achieved using the bicarbonate-bearing solution, and high P{sub CO2}. Specific conditions include: 185 C; P{sub CO2}=150 atm; 30% solids. Studies suggest that the mineral dissolution rate is not solely surface controlled, while the carbonate precipitation rate is primarily dependent on the bicarbonate concentration of the slurry. Current and future activities include further examination of the reaction pathways and pretreatment options, the development of a continuous flow reactor, and an evaluation of the economic feasibility of the process.

  11. Geomathematical characterisation of the mineralization indicators: a case study from Tincova magmatic intrusion (Romania

    Directory of Open Access Journals (Sweden)

    George Tudor

    2011-10-01

    Full Text Available Indicators of the hydrothermal mineralization in the Tincova Laramian intrusion were tested at the contact zone between the intrusive body and the metamorphic host rocks. The mineralization consists of Cu, Pb and Zn sulfides, arsenopyrite, pyrrhotite and pyrite in gangue of quartz, carbonates, feldspar, sericite or clay minerals, and includes areas of hydrothermal alteration or oxidation. Seventy-nine samples were analyzed and processed as two distinct populations. Geomathematical methods highlight the importance of factors such as the shape, sizes of the mineralized zones and geological processes involved in the ore genesis. Trend maps for Cu, Pb + Zn, and Ag interpolated by kriging method, show anomalous values of Cu along the edge of the intrusive body with the metamorphic country rocks, and Pb + Zn in a marginal area. Departing from the study of correlations between different variables, the factor analysis (R-mode highlights five factors that represent a sequence of geological processes: pneumatolytic phase (Sn, deposition of the association with arsenopyrite, pyrrhotite, pyrite, molybdenite (Ni, Co, Mo, formation of the Cu ± Ag + Bi sulfide mineralization, galena mineralization ± Au, hydrothermal alteration processes (addition of Ba, Sr, V. The dependence of Cu on other elements is performed by multiple linear regression, resulting an equation statistically tested by F-test, and interpreted as originating in a phase of the metallogenetic processes. The shape of the Cu-Mo mineralized stockwork from Vălişor Valley area has been studied on the basis of samples from drillings, Cu trend maps at three depth levels, and a three-dimensional model.

  12. Bioinspired magnetite synthesis via solid precursor phases

    NARCIS (Netherlands)

    Lenders, J.J.M.; Mirabello, G.; Sommerdijk, N.A.J.M.

    2016-01-01

    Living organisms often exploit solid but poorly ordered mineral phases as precursors in the biomineralization of their inorganic body parts. Generally speaking, such precursor-based approaches allow the organisms-without the need of high supersaturation levels-to accumulate significant quantities of

  13. Effect of HIP/ribosomal protein L29 deficiency on mineral properties of murine bones and teeth.

    Science.gov (United States)

    Sloofman, Laura G; Verdelis, Kostas; Spevak, Lyudmila; Zayzafoon, Majd; Yamauchi, Mistuo; Opdenaker, Lynn M; Farach-Carson, Mary C; Boskey, Adele L; Kirn-Safran, Catherine B

    2010-07-01

    Mice lacking HIP/RPL29, a component of the ribosomal machinery, display increased bone fragility. To understand the effect of sub-efficient protein synthetic rates on mineralized tissue quality, we performed dynamic and static histomorphometry and examined the mineral properties of both bones and teeth in HIP/RPL29 knock-out mice using Fourier transform infrared imaging (FTIRI). While loss of HIP/RPL29 consistently reduced total bone size, decreased mineral apposition rates were not significant, indicating that short stature is not primarily due to impaired osteoblast function. Interestingly, our microspectroscopic studies showed that a significant decrease in collagen crosslinking during maturation of HIP/RPL29-null bone precedes an overall enhancement in the relative extent of mineralization of both trabecular and cortical adult bones. This report provides strong genetic evidence that ribosomal insufficiency induces subtle organic matrix deficiencies which elevates calcification. Consistent with the HIP/RPL29-null bone phenotype, HIP/RPL29-deficient teeth also showed reduced geometric properties accompanied with relative increased mineral densities of both dentin and enamel. Increased mineralization associated with enhanced tissue fragility related to imperfection in organic phase microstructure evokes defects seen in matrix protein-related bone and tooth diseases. Thus, HIP/RPL29 mice constitute a new genetic model for studying the contribution of global protein synthesis in the establishment of organic and inorganic phases in mineral tissues. 2010 Elsevier Inc. All rights reserved.

  14. Enhanced99Tc retention in glass waste form using Tc(IV)-incorporated Fe minerals

    OpenAIRE

    Um, W; Luksic, SA; Wang, G; Saslow, S; Kim, DS; Schweiger, MJ; Soderquist, CZ; Bowden, ME; Lukens, WW; Kruger, AA

    2017-01-01

    © 2017 Elsevier B.V. Technetium ( 99 Tc) immobilization by doping into iron oxide mineral phases may alleviate the problems with Tc volatility during vitrification of nuclear waste. Because reduced Tc, Tc(IV), substitutes for Fe(III) in the crystal structure by a process of Tc reduction from Tc(VII) to Tc(IV) followed by co-precipitation of Fe oxide minerals, two Tc-incorporated Fe minerals (Tc-goethite and Tc-magnetite/maghemite) were prepared and tested for Tc retention in glass melt sample...

  15. Study of blood pressure among coal miners

    Energy Technology Data Exchange (ETDEWEB)

    Chandon; Dhar, B.B.; Singh, A.K.P.; Sahay, L.K. [Central Mining Research Institute, Dhanbad (India)

    1997-12-31

    The aim of the work was to assess the prevalence of hypertension among 2772 coal miners and to establish the relationship of hypertension with family history, living conditions, dietary habits, and other associated medical parameters. 4 refs., 5 tabs.

  16. Contributions of Fe Minerals to Abiotic Dechlorination

    Science.gov (United States)

    Most applications of enhanced in situ bioremediation are based on biological reductive dechlorination. Anaerobic metabolism can also produce reactive minerals that allow for in situ biogeochemical transformation of chlorinated organic contaminants such as PCE, TCE, and cis-DCE. ...

  17. Status of mineral resources evaluation and forecast

    International Nuclear Information System (INIS)

    Ma Hanfeng; Li Ziying; Luo Yi; Li Shengxiang; Sun Wenpeng

    2007-01-01

    The work of resources evaluation and forecast is a focus to the governments of every country in the world, it is related to the establishment of strategic policy on the national mineral resources. In order to quantitatively evaluate the general potential of uranium resources in China and better forecast uranium deposits, this paper briefly introduces the method of evaluating total amount of mineral resources, especially 6 usual prospective methods which are recommended in international geology comparison programs, as well as principle of usual mineral resources quantitative prediction and its steps. The work history of mineral resources evaluation and forecast is reviewed concisely. Advantages and disadvantages of each method, their application field and condition are also explained briefly. At last, the history of uranium resources evaluation and forecast in China and its status are concisely outlined. (authors)

  18. Statistical models for optimizing mineral exploration

    International Nuclear Information System (INIS)

    Wignall, T.K.; DeGeoffroy, J.

    1987-01-01

    The primary purpose of mineral exploration is to discover ore deposits. The emphasis of this volume is on the mathematical and computational aspects of optimizing mineral exploration. The seven chapters that make up the main body of the book are devoted to the description and application of various types of computerized geomathematical models. These chapters include: (1) the optimal selection of ore deposit types and regions of search, as well as prospecting selected areas, (2) designing airborne and ground field programs for the optimal coverage of prospecting areas, and (3) delineating and evaluating exploration targets within prospecting areas by means of statistical modeling. Many of these statistical programs are innovative and are designed to be useful for mineral exploration modeling. Examples of geomathematical models are applied to exploring for six main types of base and precious metal deposits, as well as other mineral resources (such as bauxite and uranium)

  19. Superficial mineral resources of the Indian Ocean

    Digital Repository Service at National Institute of Oceanography (India)

    Siddiquie, H.N.; Hashimi, N.H.; Gujar, A; Valsangkar, A

    The sea floor of the Indian Ocean and the continental margins bordering the ocean are covered by a wide variety of terrigenous, biogenous and anthigenic mineral deposits. The biogenous deposits in the Indian Ocean comprise the corals on shallow...

  20. NOAA and MMS Marine Minerals Geochemical Database

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Marine Minerals Geochemical Database was created by NGDC as a part of a project to construct a comprehensive computerized bibliography and geochemical database...