WorldWideScience

Sample records for type bang-1 gel

  1. Inclusion type radiochromic gel dosimeter for threedimensional dose verification

    Science.gov (United States)

    Usui, Shuji; Yoshioka, Munenori; Hayashi, Shin-ichiro; Tominaga, Takahiro

    2015-01-01

    For the verification of 3D dose distributions in modern radiation therapy, a new inclusion type radiochromic gel detector has been developed. In this gel, a hydrophobic leuco dye (leucomalachite green: LMG) was dissolved in water as an inclusion complex with highly branched cyclic dextrin. The radiation induced radical oxidation property of the LMG gel with various sensitizers was investigated. As a result, the optical dose responses were enhanced by the addition of bromoacetic acid and manganese (II) chloride. Unfavorable auto-oxidation of the gel was reduced when it was stored at 4°C.

  2. Densification and crystallization behaviour of colloidal cordierite-type gels

    Directory of Open Access Journals (Sweden)

    LJILJANA KOSTIC-GVOZDENOVIC

    2001-05-01

    Full Text Available Three cordierite-type gels were prepared from an aqueous solution of Mg(NO32, a boehmite sol and silica sols of very small particle sizes. The effect of varying the silica particle size on the crystallization and densification behaviour was studied. Phase development was examined by thermal analysis and X-ray diffraction, while the densification behaviour was characterized by measuring the linear shrinkage of pellets. The activation energy of densification by viscous flow was determined using the Franckel model for non-isothermal conditions and a constant heating rate. The results show that spinel crystallizes from the colloidal gels prior to cristobalite, and their reaction gives a-cordierite, which is specific for three-phase gels. Decreasing the silica particles size lowers the cristobalite crystallization temperature and the a-cordierite formation temperature. The activation energy of densification by viscous flow is lower and the densification more efficient, the smaller the silica particles are.

  3. Papain-gel Degrades Intact Nonmineralized Type I Collagen Fibrils

    Science.gov (United States)

    BERTASSONI, L. E.; MARSHALL, G. W.

    2010-01-01

    Summary Papain-gel has been utilized as a chemomechanical material for caries removal due to its ability to preserve underlying sound dentin. However, little is known about the effect of the papain enzyme on intact type I collagen fibrils that compose the dentin matrix. Here we sought to define structural changes that occur in intact type I collagen fibrils after an enzymatic treatment with a papaingel. Intact and nonmineralized type I collagen fibrils from rat tail were obtained and treated with a papain-gel (Papacarie) for 30 s, rinsed with water and imaged using an atomic force microscope (AFM). Additionally, polished healthy dentin specimens were also treated using the same protocol described above and had their elastic modulus (E) and hardness (H) measured by means of AFM-based nanoindentation. AFM images showed that the papain-gel induced partial degradation of the fibrils surface, yet no rupture of fibrils was noticed. The distinction between gap and overlap zones of fibrils vanished in most regions after treatment, and overlap zones appeared to be generally more affected. Mechanical data suggested a gradual decrease in E and H after treatments. A significant two-fold drop from the values of normal dentin (E= 20 +/− 1.9, H = 0.8 +/− 0.08 GPa) was found after four applications (E = 9.7 +/− 3.2, H = 0.24 +/− 0.1 GPa) ( P<0.001), which may be attributed to the degradation of proteoglycans of the matrix. In summary, this study provided novel evidence that intact nonmineralized type I collagen fibrils are partially degraded by a papain-gel. PMID:20205185

  4. Comparison of Two Types of Gels in Improving Burn Wound

    Directory of Open Access Journals (Sweden)

    Rahimzadeh Golnar

    2014-01-01

    Full Text Available Objective: Kefir are natural probiotic compounds with anti-inflammatory properties, which were tested in experimental burn injury. Kefir gels were prepared from an extract of continuously cultured kefir in Man, Rogosa and Sharpe Broth medium for 48 and 96 h. Their extracts were used for evaluation of antibacterial effect against Pseudomonas aeruginosa in standard sample (ATCC 27853 and samples taken from patients with burns. The antibacterial effect of different kefir extract was assessment of minimum inhibitory concentration and minimum bactericidal concentration. The density of bacteria and percentage of organic acids (lactic and acetic acids were also determined. Materials and Methods: Similar burn injuries were made on dorsal skin surface of 40 rats. The rats were divided into 5 groups of 8 rats each. The base gel, silver sulfadiazine ointment, kefir 48 h gel, kefir 96 h gel were applied twice daily. Burn wound area was measured at baseline, 1 and 2 weeks. Results: Results indicated that by increasing the time of fermentation, concentration of lactic and acetic acid increased in orders of: Kefir 48 h < kefir 96 h, the end of the 2nd week the percentage of wound size were lowest in order of kefir 96 h gel < kefir grains 48 h gel < silver sulfadiazine 1% < untreated and based gel groups. Conclusion: In conclusion, the kefir gel therapy was an effective therapeutic approach to improve outcomes after severe burn when compared with conventional silver sulfadiazine treatment.

  5. Type I collagen gel protects murine fibrosarcoma L929 cells from TNFα-induced cell death

    International Nuclear Information System (INIS)

    Wang, Hong-Ju; He, Wen-Qi; Chen, Ling; Liu, Wei-Wei; Xu, Qian; Xia, Ming-Yu; Hayashi, Toshihiko; Fujisaki, Hitomi; Hattori, Shunji; Tashiro, Shin-ichi; Onodera, Satoshi; Ikejima, Takashi

    2015-01-01

    Murine fibrosarcoma L929 cells have been used to test efficacy of proinflammatory cytokine TNFα. In the present study, we reported on protective effect of type I collagen gel used as L929 cell culture. L929 cell grew and proliferated well on collagen gel. However, the L929 cells exhibited cobblestone-like morphology which was much different from the spread fusiform shape when cultured on conventional cell dishes as well as the cells tended to aggregate. On conventional cell culture dishes, the cells treated with TNFα became round in shape and eventually died in a necroptotic manner. The cells cultured on collagen gel, however, were completely unaffected. TNFα treatment was reported to induce autophagy in L929 cells on the plastic dish, and therefore we investigated the effect of collagen gel on induction of autophagy. The results indicated that autophagy induced by TNFα treatment was much reduced when the cells were cultured on collagen gel. In conclusion, type I collagen gel protected L929 cell from TNFα-induced cell death. - Highlights: • Collagen gel culture changed the morphology of L929 cells. • L929 cell cultured on collagen gel were resistant to TNFα-induced cell death. • Collagen gel culture inhibited TNFα-induced autophagy in L929 cells

  6. Flow and sol-gel behavior of two types of methylcellulose at various concentrations

    Science.gov (United States)

    Edelby, Y.; Balaghi, S.; Senge, B.

    2014-05-01

    In the present work, the flow and oscillatory properties of two types of Methylcellulose (MC), Methocel A4M and A40M, have been investigated. Shear rate measurement, frequency sweep and temperature sweep were used to characterize the rheological behaviour of the aqueous solutions of Methylcellulose and its thermo gels at different concentrations (0.25-2%). According to our findings, Methocel A40M and A4M both indicated pseudoplastic behavior but the consistency coefficient of A40M at 20 °C was significantly higher than A4M. The consistency coefficient of samples with high concentrations of MC (c > 1%) increased clearly after 24 h storage at 6 °C dependening on dissolution time. Effective viscosity, consistency coefficient exponentially increased with concentration. MCs exhibited 5 regions in temperature sweep spectrum, namely, sol, sol-gel transition, gel maturation, slow degradation of the gel structures and gel-sol transtion regions. They indicated the complete reversibility of the gelation with a large-hysteresis effect. Both types of MC formed true and strong gels at c > 0.75%. The gel strength and stability for Methocel A40M samples at those concentrations were a little bit weaker than that for Methocel A4M samples. Although, the flow behaviors of two types of methylcellulose at 20 °C were significantly different, the thermo gels formed by them behaved relatively identical.

  7. Comparison of restriction enzymes for pulsed-field gel electrophoresis typing of Moraxella catarrhalis.

    Science.gov (United States)

    Marti, Sara; Puig, Carmen; Domenech, Arnau; Liñares, Josefina; Ardanuy, Carmen

    2013-07-01

    NotI, the most prevalent restriction enzyme used for typing Moraxella catarrhalis, failed to digest genomic DNA from respiratory samples. An improved pulsed-field gel electrophoresis (PFGE) methodology determined SpeI as the best choice for typing this bacterial species, with a good restriction of clinical samples and a good clustering correlation with NotI.

  8. Comparison of ompP5 sequence-based typing and pulsed-filed gel ...

    African Journals Online (AJOL)

    In this study, comparison of the outer membrane protein P5 gene (ompP5) sequence-based typing with pulsed-field gel electrophoresis (PFGE) for the genotyping of Haemophilus parasuis, the 15 serovar reference strains and 43 isolates were investigated. When comparing the two methods, 31 ompP5 sequence types ...

  9. Comparison of ompP5 sequence-based typing and pulsed-filed gel ...

    African Journals Online (AJOL)

    Yomi

    2012-03-15

    Mar 15, 2012 ... In this study, comparison of the outer membrane protein P5 gene (ompP5) sequence-based typing with pulsed-field gel electrophoresis (PFGE) for the genotyping of Haemophilus parasuis, the 15 serovar reference strains and 43 isolates were investigated. When comparing the two methods, 31 ompP5.

  10. Thermal denaturation of type I collagen vitrified gels

    International Nuclear Information System (INIS)

    Xia, Zhiyong; Calderon-Colon, Xiomara; Trexler, Morgana; Elisseeff, Jennifer; Guo, Qiongyu

    2012-01-01

    Highlights: ► We analyzed the denaturation of vitrigels synthesized under different conditions. ► Overall denaturation kinetics consisted of both reversible and irreversible steps. ► More stable vitrigels were formed under high level of vitrification. - Abstract: The denaturation kinetics of type I collagen vitrigels synthesized under different vitrification time and temperature were analyzed by the classical Kissinger approach and the advanced model free kinetics (AMFK) using the Vyazovkin algorithm. The AMFK successfully elucidated the overall denaturation into reversible and irreversible processes. Depending on vitrification conditions, the activation energy for the irreversible process ranged from 100 to 200 kJ/mol, and the reversible enthalpy ranged from 250 to 300 kJ/mol. All of these values increased with the vitrification time and temperature, indicating that a more stable and complex structure formed with increased vitrification. The classical Kissinger method predicted the presence of a critical temperate of approximately 60 °C for the transition between reversible and irreversible processes. Scanning electron microscopy revealed the presence of fibril structures in vitrigels both before and after full denaturation; however the fibrils had became thicker and rougher after denaturation.

  11. Neutron spin-echo studies on dynamic and static fluctuations in two types of poly(vinyl alcohol) gels

    International Nuclear Information System (INIS)

    Kanaya, T.; Takahashi, N.; Nishida, K.; Seto, H.; Nagao, M.; Takeda, T.

    2005-01-01

    We report neutron spin-echo measurements on two types of poly(vinyl alcohol) (PVA) gels. The first is PVA gel in a mixture of dimethyl sulfoxide (DMSO) and water with volume ratio 60/40, and the second is PVA gel in an aqueous borax solution. The observed normalized intermediate scattering functions I(Q,t)/I(Q,0) are very different between them. The former I(Q,t)/I(Q,0) shows a nondecaying component in addition to a fast decay, but the latter does not have the nondecaying one. This clearly indicates that the fluctuations in the former PVA gel consist of static and dynamic fluctuations whereas the latter PVA gel does include only the dynamic fluctuations. The dynamic fluctuations of the former and latter gels have been analyzed in terms of a restricted motion in the network and Zimm motion, respectively, and the origins of these motions will be discussed

  12. Analysis of one-dimensional gels and two-dimensional Serwer-type gels on the basis of the extended Ogston model using personal computers.

    Science.gov (United States)

    Tietz, D

    1991-01-01

    This report presents the stand-alone computer application ELPHOFIT, a software package for the analysis of gel electrophoretic data based on Ferguson plots. Either conventional one-dimensional gels or two-dimensional agarose gels (Serwer-type) can be evaluated. Special emphasis is on the latter gel type, which has been applied previously for the separation of DNA, intact viruses and polydisperse meningitis vaccines. ELPHOFIT is designed for Macintosh PCs and for the IBM XT, AT, PS/2 and compatibles. The program operates interactively with the user, who determines the course of evaluation. Data input is in the format of files providing values of gel electrophoretic migration distances or particle mobility (absolute or relative). Data processing involves a simultaneous least-square curve fitting algorithm (Newton-Gauss, Marquardt-Levenberg) which uses equations derived from the extended Ogston model. Functions are fit to the database by adjusting their variables, representing physical parameters of the gel and the electrophoresed particle. The program output consists of tables and graphics accompanied by an explanatory text providing the following information: (i) radius and free mobility of the electrophoresed particle, (ii) fiber radius, length and volume, mean or median pore radius of the gel, (iii) linear Ferguson plots, (iv) iso-free-mobility/iso-size nomogram for two-dimensional gels, (v) confidence ellipses, (vi) required parameters for image processing program GELFIT and (vii) goodness-of-fit and other statistical parameters, such as standard errors, dependency values, root-mean-square (RMS) error and determination coefficient. Other features of the program are (i) simulation of Serwer-type two-dimensional electrophoresis, (ii) standardization according to size, or size and free mobility, (iii) the conversion of particle radii to molecular (or particle) weight and vice versa, (iv) interconversion of DNA size specifications, i.e. the number of base pairs and

  13. Preparation and Performance of an Adsorption Type Gel Plugging Agent as Enhanced Oil Recovery Chemical

    Directory of Open Access Journals (Sweden)

    Xiaoping Qin

    2015-01-01

    Full Text Available A novel adsorption type gel plugging agent (ATGPA was prepared using acrylamide (AM, acrylic acid (AA, diallyl dimethyl ammonium chloride (DMDAAC, 2-acrylamido-2-methylpropanesulfonate (AMPS, formaldehyde (HCHO, resorcinol (C6H6O2, and thiocarbamide (CH4N2S as raw materials under mild conditions. ATGPA was characterized by infrared (IR spectroscopy, elemental analysis, and scanning electron microscope (SEM. It was found that ATGPA exhibited higher elastic modulus (G′ and viscous modulus (G′′ than AM/AA gel plugging agent (AAGPA under the same scanning frequency. It was also found that ATGPA had moderate temperature resistance and salt tolerance. Core plugging tests results indicated that ATGPA could achieve up to higher plugging rate (PR than AAGPA (97.2% versus 95.7% at 65°C. In addition, ATGPA possessed stronger antiscouring ability by core plugging experiments at 65°C.

  14. Suitability of PCR fingerprinting, infrequent-restriction-site PCR, and pulsed-field gel electrophoresis, combined with computerized gel analysis, in library typing of Salmonella enterica serovar enteritidis

    DEFF Research Database (Denmark)

    Garaizar, J.; Lopez-Molina, N.; Laconcha, I.

    2000-01-01

    Strains of Salmonella enterica (n = 212) of different serovars and phage types were used to establish a library typing computerized system for serovar Enteritidis on the basis of PCR fingerprinting, infrequent-restriction-site PCR (IRS-PCR), or pulsed-field gel electrophoresis (PFGE). The rate...... showed an intercenter reproducibility value of 93.3%. The high reproducibility of PFGE combined with the previously determined high discrimination directed its use for library typing. The use of PFGE with enzymes XbaI, BlnI, and SpeI for library typing of serovar Enteritidis was assessed with GelCompar 4.......0 software, Three computer libraries of PFGE DNA profiles were constructed, and their ability to recognize new DNA profiles was analyzed. The results obtained pointed out that the combination of PFGE with computerized analysis could be suitable in long-term epidemiological comparison and surveillance...

  15. Estimation of types I and III collagens in whole tissue by quantitation of CNBr peptides on SDS-polyacrylamide gels.

    Science.gov (United States)

    Light, N D

    1982-03-18

    The electrophoretic and staining characteristics of CNBr peptides of purified bovine and human types I and III collagens were investigated on SDS-polyacrylamide slab gels. All the major CNBr peptides of both types of collagen showed linear staining characteristics with Coomassie brilliant blue up to a total protein concentration of 150 micrograms per gel track. The amount of each type of collagen present in model mixtures was calculated from quantitations of the alpha 1(I)CB8 (type I) and alpha 1(III)CB8 (type III) peptides after resolution on 10% (w/v) SDS-polyacrylamide slab gels. The accuracy of the method was assessed, shown to give less than 15% error in mixtures containing more than 15% type III, and its applicability to the estimation of ratios of type I and type III collagens in whole tissue was determined.

  16. The impact of the oxygen scavenger on the dose-rate dependence and dose sensitivity of MAGIC type polymer gels

    Science.gov (United States)

    Khan, Muzafar; Heilemann, Gerd; Kuess, Peter; Georg, Dietmar; Berg, Andreas

    2018-03-01

    Recent developments in radiation therapy aimed at more precise dose delivery along with higher dose gradients (dose painting) and more efficient dose delivery with higher dose rates e.g. flattening filter free (FFF) irradiation. Magnetic-resonance-imaging based polymer gel dosimetry offers 3D information for precise dose delivery techniques. Many of the proposed polymer gels have been reported to exhibit a dose response, measured as relaxation rate ΔR2(D), which is dose rate dependent. A lack of or a reduced dose-rate sensitivity is very important for dosimetric accuracy, especially with regard to the increasing clinical use of FFF irradiation protocols with LINACs at high dose rates. Some commonly used polymer gels are based on Methacrylic-Acid-Gel-Initiated-by-Copper (MAGIC). Here, we report on the dose sensitivity (ΔR2/ΔD) of MAGIC-type gels with different oxygen scavenger concentration for their specific dependence on the applied dose rate in order to improve the dosimetric performance, especially for high dose rates. A preclinical x-ray machine (‘Yxlon’, E  =  200 kV) was used for irradiation to cover a range of dose rates from low \\dot{D} min  =  0.6 Gy min-1 to high \\dot{D} max  =  18 Gy min-1. The dose response was evaluated using R2-imaging of the gel on a human high-field (7T) MR-scanner. The results indicate that all of the investigated dose rates had an impact on the dose response in polymer gel dosimeters, being strongest in the high dose region and less effective for low dose levels. The absolute dose rate dependence \\frac{(Δ R2/Δ D)}{Δ \\dot{D}} of the dose response in MAGIC-type gel is significantly reduced using higher concentrations of oxygen scavenger at the expense of reduced dose sensitivity. For quantitative dose evaluations the relative dose rate dependence of a polymer gel, normalized to its sensitivity is important. Based on this normalized sensitivity the dose rate sensitivity was reduced distinctly

  17. The impact of the oxygen scavenger on the dose-rate dependence and dose sensitivity of MAGIC type polymer gels.

    Science.gov (United States)

    Khan, Muzafar; Heilemann, Gerd; Kuess, Peter; Georg, Dietmar; Berg, Andreas

    2018-03-12

    Recent developments in radiation therapy aimed at more precise dose delivery along with higher dose gradients (dose painting) and more efficient dose delivery with higher dose rates e.g. flattening filter free (FFF) irradiation. Magnetic-resonance-imaging based polymer gel dosimetry offers 3D information for precise dose delivery techniques. Many of the proposed polymer gels have been reported to exhibit a dose response, measured as relaxation rate ΔR2 (D) , which is dose rate dependent. A lack of or a reduced dose-rate sensitivity is very important for dosimetric accuracy, especially with regard to the increasing clinical use of FFF irradiation protocols with LINACs at high dose rates. Some commonly used polymer gels are based on Methacrylic-Acid-Gel-Initiated-by-Copper (MAGIC). Here, we report on the dose sensitivity (ΔR2/ΔD) of MAGIC-type gels with different oxygen scavenger concentration for their specific dependence on the applied dose rate in order to improve the dosimetric performance, especially for high dose rates. A preclinical x-ray machine ('Yxlon', E  =  200 kV) was used for irradiation to cover a range of dose rates from low [Formula: see text] min   =  0.6 Gy min -1 to high [Formula: see text] max   =  18 Gy min -1 . The dose response was evaluated using R2-imaging of the gel on a human high-field (7T) MR-scanner. The results indicate that all of the investigated dose rates had an impact on the dose response in polymer gel dosimeters, being strongest in the high dose region and less effective for low dose levels. The absolute dose rate dependence [Formula: see text] of the dose response in MAGIC-type gel is significantly reduced using higher concentrations of oxygen scavenger at the expense of reduced dose sensitivity. For quantitative dose evaluations the relative dose rate dependence of a polymer gel, normalized to its sensitivity is important. Based on this normalized sensitivity the dose rate sensitivity was reduced

  18. Physics of soft hyaluronic acid-collagen type II double network gels

    Science.gov (United States)

    Morozova, Svetlana; Muthukumar, Murugappan

    2015-03-01

    Many biological hydrogels are made up of multiple interpenetrating, charged components. We study the swelling, elastic diffusion, mechanical, and optical behaviors of 100 mol% ionizable hyaluronic acid (HA) and collagen type II fiber networks. Dilute, 0.05-0.5 wt% hyaluronic acid networks are extremely sensitive to solution salt concentration, but are stable at pH above 2. When swelled in 0.1M NaCl, single-network hyaluronic acid gels follow scaling laws relevant to high salt semidilute solutions; the elastic shear modulus G' and diffusion constant D scale with the volume fraction ϕ as G' ~ϕ 9 / 4 and D ~ϕ 3 / 4 , respectively. With the addition of a collagen fiber network, we find that the hyaluronic acid network swells to suspend the rigid collagen fibers, providing extra strength to the hydrogel. Results on swelling equilibria, elasticity, and collective diffusion on these double network hydrogels will be presented.

  19. PENGARUH KONSUMSI GEL DAN LARUTAN RUMPUT LAUT (Eucheuma cottonii TERHADAP HIPERKOLESTEROLEMIA DARAH TIKUS WISTAR [The Consumption Effect of Gel and Solution Types of Eucheuma cottonii Seaweeds on Hypercholesterolemic of Blood Wistar Rat

    Directory of Open Access Journals (Sweden)

    Hardoko

    2008-12-01

    Full Text Available The consumption effect of gel and solution of Eucheuma cottonii seaweed on blood lipid level were studied on hypercholesterolemic male wistar rat. The rat were made hypercholesterolemic by a ration that contained high lipid and cholesterol, and then they were given standard ration orally and 10, 15, and 20% (w/w feed of gel and solution seaweed parenterally. The results show that the standard ration could not reduce hypercholesterolemic to normal level while gel and solution of the seaweed could. The gel type of the seaweed has higher capacity decrease of cholesterol and triglyceride blood level. The consumption of seaweed gel 20% and 15% could reduce cholesterol to normal level in 9 and 15 days, respectively, while the solution type 20% needed 18 days. The seaweed gel 10%, solution 15% and 10% could reduce blood cholesterol level, but they could not reach to normal level in 18 days.

  20. Molecular typing of Salmonella enterica serovar Sofia in Australia by pulsed-field gel electrophoresis and repetitive element PCR typing.

    Science.gov (United States)

    Gan, E; Smooker, P M; Coloe, P J

    2010-07-01

    In this study, we used two molecular fingerprinting methods to investigate the genetic and clonal relationship shared by Australian Salmonella Sofia isolates. A total of 84 Australian Salm. Sofia isolates from various states in Australia were typed using pulsed-field gel electrophoresis (PFGE) (XbaI and SpeI) and repetitive element PCR (REP1R-I primer). The previous problem of DNA degradation of Salm. Sofia strains was solved by modifying the lysis solution used to treat the bacterial plugs, allowing Salm. Sofia to be subtyped using PFGE. Molecular typing of isolates resulted in the generation of eight XbaI, six SpeI and five REP1 pattern profiles. Individual typing methods showed low discrimination index values (Sofia. The Australian Salm. Sofia isolates only showed limited genetic diversity and probably share a clonal relationship. A majority of the Salm. Sofia isolates were not geographically restricted with the predominant pattern subtype observed amongst the isolates from various states. We have successfully devised a PFGE protocol that counteracts DNase activity of Salm. Sofia, enabling typing of this serovar. © 2010 The Authors. Journal compilation © 2010 The Society for Applied Microbiology.

  1. Fluid diversion and sweep improvement with chemical gels in oil recovery processes. [Four types of gels: resorcinol-formaldehyde; colloidal silica; Cr sup 3+ (chloride)-xanthan; and Cr sup 3+ (acetate)-polyacrylamide

    Energy Technology Data Exchange (ETDEWEB)

    Seright, R.S.; Martin, F.D.

    1992-09-01

    The objectives of this project were to identify the mechanisms by which gel treatments divert fluids in reservoirs and to establish where and how gel treatments are best applied. Several different types of gelants were examined, including polymer-based gelants, a monomer-based gelant, and a colloidal-silica gelant. This research was directed at gel applications in water injection wells, in production wells, and in high-pressure gas floods. The work examined how the flow properties of gels and gelling agents are influenced by permeability, lithology, and wettability. Other goals included determining the proper placement of gelants, the stability of in-place gels, and the types of gels required for the various oil recovery processes and for different scales of reservoir heterogeneity. During this three-year project, a number of theoretical analyses were performed to determine where gel treatments are expected to work best and where they are not expected to be effective. The most important, predictions from these analyses are presented. Undoubtedly, some of these predictions will be controversial. However, they do provide a starting point in establishing guidelines for the selection of field candidates for gel treatments. A logical next step is to seek field data that either confirm or contradict these predictions. The experimental work focused on four types of gels: (1) resorcinol-formaldehyde, (2) colloidal silica, (3) Cr{sup 3+}(chloride)-xanthan, and (4) Cr{sup 3+}(acetate)-polyacrylamide. All experiments were performed at 41{degrees}C.

  2. Synthesis and Characterization of a Gel-Type Electrolyte with Ionic Liquid Added for Dye-Sensitized Solar Cells

    Directory of Open Access Journals (Sweden)

    Le-Yan Shi

    2013-01-01

    Full Text Available This study intends to develop the electrolyte needed in dye-sensitized solar cells (DSSCs. Moreover, three different ionic liquids in different molalities are added to the gel-type electrolyte. Experimental results show that the DSSC composed of the gel-type electrolyte with no ionic liquid added can acquire 4.13% photoelectric conversion efficiency. However, the DSSC composed of the gel-type electrolyte with 0.4 M of 1-butyl-3-methylimidazolium chloride added has an open-circuit voltage of 810 mV, a short-circuit current density of 9.56 mA/cm2, and photoelectric conversion efficiency reaching 4.89%. Comparing this DSSC with the DSSC with no ionic liquid added, the photoelectric conversion efficiency can be enhanced by 18.4%. As to durability, the DSSC composed of the gel-type electrolyte with ionic liquid added still has a photoelectric conversion efficiency of 3.28% on the 7th day after it is stored in an enclosed space and maintains 0.72% efficiency on the 14th day. When the proposed DSSC is compared with the DSSC prepared by using a liquid-type electrolyte, the durability of its photoelectric conversion efficiency can be increased by 7 times.

  3. Proteomic profile in glomeruli of type-2 diabetic KKAy mice using 2-dimensional differential gel electrophoresis.

    Science.gov (United States)

    Liu, Xiaodan; Yang, Gang; Fan, Qiuling; Wang, Lining

    2014-12-17

    Diabetic nephropathy (DN) is a leading cause of end-stage renal disease. To search for glomerular proteins associated with early-stage DN, glomeruli of spontaneous type 2 diabetic KKAy mice were analyzed by 2-dimensional differential gel electrophoresis (2D-DIGE). Glomeruli of 20-week spontaneous type 2 diabetic KKAy mice and age-matched C57BL/6 mice were isolated by kidney perfusion with magnetic beads. Proteomic profiles of glomeruli were investigated by using 2D-DIGE and matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) mass spectrometry. Western blot analysis was used to confirm the results of proteomics. Immunohistochemical and semi-quantitative analysis were used to confirm the differential expression of prohibitin and annexin A2 in glomeruli. We identified 19 differentially expressed proteins - 17 proteins were significantly up-regulated and 2 proteins were significantly down-regulated in glomeruli of diabetic KKAy mice. Among them, prohibitin and annexin A2 were up-regulated and Western blot analysis validated the same result in proteomics. Immunohistochemical analysis also revealed up-regulation of prohibitin and annexin A2 in glomeruli of KKAy mice. Our findings suggest that prohibitin and annexin A2 may be associated with early-stage DN. Further functional research might help to reveal the pathogenesis of DN.

  4. Molecular Typing of Salmonella Isolates in Poultry by Pulsed-Field Gel Electrophoresis in Iran

    Directory of Open Access Journals (Sweden)

    Narges Golab

    2014-11-01

    Full Text Available Background: Salmonella is one of the most widespread zoonotic enter pathogenic microorganisms found in the global food chain. Poultryand Poultry products have been identified as one of the important foodborne sources of Salmonella. Pulsed-Field Gel Electrophoresis (PFGE is a gold standard typing method for identification of Salmonella isolates during outbreaks and epidemiological investigations. Objectives: The aim of this study was to carry out molecular typing of Salmonella enterica spp. by PFGE technique. Materials and Methods: All 47 Salmonella isolates were serotyped and then subjected to PFGE. Total isolates were analyzed by means of the molecular technique XbaI PFGE. Results: In the current work, PFGE and serotyping were used to subtype 47 Salmonella isolates belonging to 22 different serotypes and derived from poultry. Thirty-nine PFGE patterns out of 47 isolates were obtained. The Discrimination Index (DI by serotyping (0.93 was lower than PFGE (DI = 0.99. Conclusions: In conclusion, molecular methods such as PFGE can be used for epidemiological characterization of Salmonella serotypes.

  5. Optimization of a pulsed-field gel electrophoresis for molecular typing of Proteus mirabilis

    Directory of Open Access Journals (Sweden)

    Alper Karagöz

    2013-09-01

    Full Text Available Objective: For the detection of outbreaks caused byProteus mirabilis, strains clonal relations are determinedmethods as “pulsed-field gel electrophoresis (PFGE”.The aim of this study was optimization of a pulsed-fieldgel electrophoresis for molecular typing of P. mirabilis.Methods: In this study, PFGE’ protocol is optimized foruse in molecular typing of P. mirabilis. Phylogenetic analyzesof strains were evaluated with Bionumerics softwaresystem (version 6.01; Applied Maths, Sint-Martens-Latem, Belgium.Results: This protocol compared with Gram-negativebacteria PFGE protocols, NotI enzyme is suitable for thisbacterium. Electrophoresis conditions should be revealedas; - block 1: initial pulse duration 1 sec, ending pulseduration 30 sec, striking angle 120°, the current 6 V/cm2,temperature 14°C, time 8 hours; - block 2: initial pulseduration 30 sec, ending pulse duration 70 sec, strikingangle 120°, the current 6 V/cm2, temperature 14°C, time16 hours; - TBE, pH=8.4.Conclusion: P. mirabilis strains were typed by PFGE andBionumerics analysis program were determined clonal relationships.The procedure was simple, reproducible andsuitable for these bacteria. Also it was evaluated, becauseof reducing time, the solution volumes and enzymes canbe economically. Outbreaks of nosocomial infections dueto bacteria studied assessment and the potential to provideuseful information about the degree of prevalence.This optimized protocol is allowed different centers’ PFGEresults to compare with other laboratories results. J ClinExp Invest 2013; 4 (3: 306-312Key words: Proteus mirabilis, molecular typing, pulsedfieldgel electrophoresis.

  6. Molecular Typing of Acinetobacter Baumannii Clinical Strains in Tehran by Pulsed-Field Gel Electrophoresis

    Directory of Open Access Journals (Sweden)

    Neda Farahani

    2013-03-01

    Full Text Available Background & Objective : Currently, Acinetobacter baumannii is an important nosocomial pathogen insofar as its hospital outbreaks have been described from various geographical areas. Since the discrimination of strains within a species is important for delineating nosocomial outbreaks, this study was conducted with the aim of genotyping the A. baumannii clinical strains in Tehran via the pulsed-field gel electrophoresis (PFGE method, which is the most accurate method used for the typing of bacterial species.   Materials & methods: This study was performed on 70 isolates of acinetobacter baumannii isolated from patients from Baqiyatallah, Rasoole Akram, and Milad hospitals in Tehran. Cultural and biochemical methods were used for the identification of the isolates in species level, and then susceptibility tests were carried out on 50 isolates of A. baumannii using the disk diffusion method. The PFGE method was performed on the isolates by Apa I restriction enzyme. Finally, the results of the PFGE were analyzed. Result: Acinetobacter baumannii strains isolated from hospitals in Tehran showed seven different genetic patterns, two of which were sporadic . Also, genotypic profiles were different in each hospital, and different patterns of genetic resistance to common antibiotics were observed. Conclusion: A lthough diversity was observed among the strains of A. baumannii by the PFGE method in Tehran, no epidemic strains were found among them.  

  7. Molecular Typing of Mycobacterium intracellulare Using Pulsed-Field Gel Electrophoresis, Variable-Number Tandem-Repeat Analysis, Mycobacteria Interspersed Repetitive-Unit-Variable-Number Tandem Repeat Typing, and Multilocus Sequence Typing: Molecular Characterization and Comparison of Each Typing Methods

    OpenAIRE

    Jeon, Semi; Lim, Nara; Kwon, Seungjik; Shim, Taesun; Park, Misun; Kim, Bum-Joon; Kim, Seonghan

    2014-01-01

    Objectives Mycobacterium intracellulare is the major causative agent of nontuberculous mycobacteria-related pulmonary infections. The strain typing of M. intracellulare is important for the treatment and control of its infections. We compared the discrimination capacity and effective value of four different molecular typing methods. Methods Antibiotic susceptibility testing, hsp65 and rpoB sequencing, pulsed-field gel electrophoresis (PFGE), multilocus sequence typing (MLST), mycobacteria int...

  8. Method for the typing of Clostridium difficile based on polyacrylamide gel electrophoresis of (/sup 35/S)methionine-labeled proteins

    Energy Technology Data Exchange (ETDEWEB)

    Tabaqchali, S.; O' Farrell, S.; Holland, D.; Silman, R.

    1986-01-01

    A typing method for Clostridium difficile based on the incorporation of (/sup 35/S)methionine into cellular proteins, their separation by sodium dodecyl sulfate-polyacrylamide gel electrophoresis, and their visualization by autoradiography is described. On analysis of the radiolabeled-protein profiles, nine distinct groups were observed (A to E and W to Z). The method, which is simple, reproducible, and readily expandable, has been applied in epidemiological studies to demonstrate cross-infection and hospital acquisition of C. difficile.

  9. Thermoresponsive Gels

    OpenAIRE

    Taylor, M. Joan; Tomlins, P.; Sahota, T. S.

    2016-01-01

    An invited review and relates to the responsive gel used in the "artificial pancreas" work og INsmart, DMU. This article is an Open Access journal. Thermoresponsive gelling materials constructed from natural and synthetic polymers can be used to provide triggered action and therefore customised products such as drug delivery and regenerative medicine types as well as for other industries. Some materials give Arrhenius-type viscosity changes based on coil to globule transitions. Others ...

  10. Computational Fluid Dynamics Modelling and Experimental Study on a Single Silica Gel Type B

    Directory of Open Access Journals (Sweden)

    John White

    2012-01-01

    Full Text Available The application of computational fluid dynamics (CFDs in the area of porous media and adsorption cooling system is becoming more practical due to the significant improvement in computer power. The results from previous studies have shown that CFD can be useful tool for predicting the water vapour flow pattern, temperature, heat transfer and flow velocity and adsorption rate. This paper investigates the effect of silica gel granular size on the water adsorption rate using computational fluid dynamics and gravimetric experimental (TGA method.

  11. Genotypic characterization of Salmonella by multilocus sequence typing, pulsed-field gel electrophoresis and amplified fragment length polymorphism

    DEFF Research Database (Denmark)

    Torpdahl, Mia; Skov, Marianne N.; Sandvang, Dorthe

    2005-01-01

    subspecies enterica isolates. A total of 25 serotypes were investigated that had been isolated from humans or veterinary sources in Denmark between 1995 and 2001. All isolates were genotyped by multilocus sequence typing (MLST), pulsed-field gel electrophoresis (PFGE) and amplified fragment length...... polymorphism (AFLP). When making genetic trees, all three methods resulted in similar clustering that often corresponded with serotype, although some serotypes displayed more diversity than others. Of the three techniques, MLST was the easiest to interpret and compare between laboratories. Unfortunately...

  12. Sol-Gel Synthesis of Ceria-Based Electrolytes and Perovskite-Type Cathodes

    Energy Technology Data Exchange (ETDEWEB)

    Pinol, S.; Calleja, A.; Capdevila, X. G.; Najib, M.; Espiell, F.

    2002-06-01

    We have successfully prepared electrolytes of Ce{sub 0.8}Sm{sub 0.2}O{sub 1.9} (SDC) and Ce{sub 0.8}Sm{sub 0.2}O{sub 1.9} (GDC) and cathodes of La{sub 1-x}Sr{sub x}CoO{sub 3} (LSCO) and La{sub 1-x}Sr{sub x}MnO{sub 3} (LSMO), useful for SOFCs, by the acrylamide sol-gel method. This method consists in the preparation of a solution from the elemental oxides and carbonates followed by a gellification with acrylamide monomer. Then, the combustion of the organic molecules is initiated, obtaining ultra fine calcined powders of the above-mentioned compounds. In this way, we have obtained high purity powders of SDC, GDC, LSCO and LSMO as confirmed by X-ray diffraction powder analysis. On the other hand, we have also studied the preparation of the same products by the solid-state reaction technique for comparison purposes. However, it was not possible to obtain pure LSCO by this ceramic method. We have observed that the optimal synthesis temperature is lower for the sol-gel samples and the final purity of the products is higher. (author)

  13. Development of new-type rapid analysis technology of polychlorinated biphenyls by using liquid chromatographic clean-up material (polyvinyl alcohol gel).

    Science.gov (United States)

    Sawatsubashi, Tetsuya; Tsukahara, Chisato; Baba, Keigo; Ohi, Etsumasa; Shinoda, Akiko; Miura, Norio

    2008-01-04

    We developed a new-type rapid polychlorinated biphenyl (PCB) analysis technology on the basis of a liquid chromatographic clean-up system combined with a large-volume injection GC-LRMS. Among 18 kinds of materials such as polymer gels, normal-phase silica gels, reversed-phase silica gels, carbon material and ion-exchange material, polyvinyl alcohol (PVA) gel and poly (hydroxylmethacrylate) gel were found to give rather good separation performance for insulating oil. Especially, PVA gel was confirmed to be the most suitable for rapid PCB analysis because of its least required quantity of fraction liquid as well as the highest resolution. Then, we confirmed elution characteristics of all PCB isomers and removal efficiency of insulating oil on PVA gel under an optimized condition, and established high-performance clean-up system using a combination of octadecyl silica gel (ODS), porous graphite carbon (PGC) and PVA gel. In this system, we applied newly valve-switching method that could remove other impurities. In addition, it was demonstrated that the proposed clean-up system could become highly sensitive and rapid PCB analysis technology with 2-h analysis time, lower measurement limit of less than 0.05 mg/kg, and a variation coefficient of less than 5%, by coupling with a large-volume injection type GC-LRMS. Thus, we can conclude that this rapid PCB analysis technology has not only good correlativity (R2>0.999) with standard analysis method but also high durability and can be fully applied to actual PCB-treatment plants.

  14. Evaluation of randomly amplified polymorphic DNA and pulsed field gel electrophoresis techniques for molecular typing of Dermatophilus congolensis.

    Science.gov (United States)

    Larrasa, José; García-Sánchez, Alfredo; Ambrose, Nicholas C; Parra, Alberto; Alonso, Juan M; Rey, Joaquín M; Hermoso-de-Mendoza, Miguel; Hermoso-de-Mendoza, Javier

    2004-11-01

    This study aimed to evaluate molecular typing methods useful for standardization of strains in experimental work on dermatophilosis. Fifty Dermatophilus congolensis isolates, collected from sheep, cattle, horse and a deer, were analyzed by randomly amplified polymorphic DNA (RAPD) method using twenty-one different primers, and the results were compared with those obtained by typing with a pulsed field gel electrophoresis (PFGE) method using the restriction digest enzyme Sse8387I. The typeability, reproducibility and discriminatory power of RAPD and Sse8387I-PFGE typing were calculated. Both typing methods were highly reproducible. Of the two techniques, Sse8387I-PFGE was the least discriminating (Dice Index (DI), 0.663) and could not distinguish between epidemiologically related isolates, whereas RAPD showed an excellent discriminatory power (DI, 0.7694-0.9722). Overall, the degree of correlation between RAPD and PFGE typing was significantly high (r, 0.8822). We conclude that the DNA profiles generated by either RAPD or PFGE can be used to differentiate epidemiologically unrelated isolates. The results of this study strongly suggest that at least two independent primers are used for RAPD typing in order to improve its discriminatory power, and that PFGE is used for confirmation of RAPD results.

  15. Comparison of automated repetitive-sequence-based polymerase chain reaction and spa typing versus pulsed-field gel electrophoresis for molecular typing of methicillin-resistant Staphylococcus aureus.

    Science.gov (United States)

    Church, Deirdre L; Chow, Barbara L; Lloyd, Tracie; Gregson, Daniel B

    2011-01-01

    Automated repetitive polymerase chain reaction (PCR) (DiversiLab, bioMérieux, St. Laurent, Quebec, Canada) and single locus sequence typing of the Staphylococcus protein A (spa) gene with spa-type assignment by StaphType RIDOM software were compared to pulsed-field gel electrophoresis (PFGE) as the "gold standard" method for methicillin-resistant Staphylococcus aureus (MRSA) typing. Fifty-four MRSA isolates were typed by all methods: 10 of known PFGE CMRSA type and 44 clinical isolates. Correct assignment of CMRSA type or cluster occurred for 47 of 54 (87%) of the isolates when using a rep-PCR similarity index (SI) of ≥95%. Rep-PCR gave 7 discordant results [CMRSA1 (3), CMRSA2 (1), CMRSA4 (1), and CMRSA10 (2)], and some CMRSA clusters were not distinguished (CMRSA10/5/9, CMRSA 7/8, and CMRSA3/6). Several spa types occurred within a single PFGE or repetitive PCR types among the 19 different spa types found. spa type t037 was shared by CMRSA3 and CMRSA6 strains, and CMRSA9 and most CMRSA10 strains shared spa type t008. Time to results for PFGE, repetitive PCR, and spa typing was 3-4 days, 24 h, and 48 h, respectively. The annual costs of using spa or repetitive PCR were 2.4× and 1.9× higher, respectively, than PFGE but routine use of spa typing would lower annual labor costs by 0.10 full-time equivalents compared to PFGE. Repetitive PCR is a good method for rapid outbreak screening, but MRSA isolates that share the same repetitive PCR or PFGE patterns can be distinguished by spa typing. Copyright © 2011 Elsevier Inc. All rights reserved.

  16. Sol-gel auto-combustion synthesis and properties of Co2Z-type hexagonal ferrite ultrafine powders

    Science.gov (United States)

    Liu, Junliang; Yang, Min; Wang, Shengyun; Lv, Jingqing; Li, Yuqing; Zhang, Ming

    2018-05-01

    Z-type hexagonal ferrite ultrafine powders with chemical formulations of (BaxSr1-x)3Co2Fe24O41 (x varied from 0.0 to 1.0) have been synthesized by a sol-gel auto-combustion technique. The average particle sizes of the synthesized powders ranged from 2 to 5 μm. The partial substitution of Ba2+ by Sr2+ led to the shrinkage of the crystal lattices and resulted in changes in the magnetic sub-lattices, which tailored the static and dynamic magnetic properties of the as-synthesized powders. As the substitution ratio of Ba2+ by Sr2+, the saturation magnetization of the synthesized powders almost consistently increased from 43.3 to 56.1 emu/g, while the real part of permeability approached to a relatively high value about 2.2 owing to the balance of the saturation magnetization and magnetic anisotropy field.

  17. Synthesis and characterization of spinel-type zinc aluminate nanoparticles by a modified sol-gel method using new precursor

    Energy Technology Data Exchange (ETDEWEB)

    Davar, Fatemeh, E-mail: davar@kashanu.ac.ir [Institute of Nano Science and Nano Technology, University of Kashan, Kashan, P. O. Box. 87317-51167 (Iran, Islamic Republic of); Salavati-Niasari, Masoud, E-mail: salavati@kashanu.ac.ir [Institute of Nano Science and Nano Technology, University of Kashan, Kashan, P. O. Box. 87317-51167 (Iran, Islamic Republic of); Department of Inorganic Chemistry, Faculty of Chemistry, University of Kashan, Kashan, P. O. Box. 87317-51167 (Iran, Islamic Republic of)

    2011-02-03

    Research highlights: > Modified sol-gel method for synthesis of spinel-type zinc aluminate nanoparticles. > Zn(en){sub 2}{sup 2+} complex (en = ethylenediamine) as new Zn{sup 2+} source. > Effect of reaction temperature on the particle size. - Abstract: In the present paper, we report the successful synthesis of spinel-type of zinc aluminate (ZnAl{sub 2}O{sub 4}) nanoparticles by a modified sol-gel method. Aluminum nitrate and Zn(en){sub 2}{sup +} complex (en: ethylenediamine) as new Zn{sup 2+} source were used. Diethylene glycol monoethyl ether and citric acid are employed as solvent and chelating agent. This method starts from the precursor complex, and involves formation of homogeneous solid intermediates, reducing atomic diffusion paths during thermal treatment. ZnO and ZnAl{sub 2}O{sub 4} nanocrystals were obtained when the precursor was heat-treated at 350 deg. C in air for 2 h. The stages of the formation of ZnAl{sub 2}O{sub 4}, as well as the characterization of the resulting compounds were done using thermo-gravimetric analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infrared spectroscopy (FTIR). The structure, particle size, and temperature of formation of ZnAl{sub 2}O{sub 4} phases were found to depend on the precursors and methods used for preparation and the calcination temperature. The lowest temperature for preparation of the ZnAl{sub 2}O{sub 4} is about 550 deg. C.

  18. Type I collagen gel induces Madin-Darby canine kidney cells to become fusiform in shape and lose apical-basal polarity.

    Science.gov (United States)

    Zuk, A; Matlin, K S; Hay, E D

    1989-03-01

    In the embryo, epithelia give rise to mesenchyme at specific times and places. Recently, it has been reported (Greenburg, G., and E. D. Hay. 1986. Dev. Biol. 115:363-379; Greenberg, G., and E. D. Hay. 1988. Development (Camb.). 102:605-622) that definitive epithelia can give rise to fibroblast-like cells when suspended within type I collagen gels. We wanted to know whether Madin-Darby canine kidney (MDCK) cells, an epithelial line, can form mesenchyme under similar conditions. Small explants of MDCK cells on basement membrane were suspended within or placed on top of extracellular matrix gels. MDCK cells on basement membrane gel are tall, columnar in shape, and ultrastructurally resemble epithelia transporting fluid and ions. MDCK explants cultured on type I collagen gel give rise to isolated fusiform-shaped cells that migrate over the gel surface. The fusiform cells extend pseudopodia and filopodia, lose cell membrane specializations, and develop an actin cortex around the entire cell. Unlike true mesenchymal cells, which express vimentin and type I collagen, fusiform cells produce both keratin and vimentin, continue to express laminin, and do not turn on type I collagen. Fusiform cells are not apically-basally polarized, but show mesenchymal cell polarity. Influenza hemagglutinin and virus budding localize to the front end or entire cell surface. Na,K-ATPase occurs intracellularly and also symmetrically distributes on the cell surface. Fodrin becomes diffusely distributed along the plasma membrane, ZO-1 cannot be detected, and desmoplakins distribute randomly in the cytoplasm. The loss of epithelial polarity and acquisition of mesenchymal cell polarity and shape by fusiform MDCK cells on type I collagen gel was previously unsuspected. The phenomenon may offer new opportunities for studying cytoplasmic and nuclear mechanisms regulating cell shape and polarity.

  19. Thermo-reversible injectable gel based on enzymatically-chopped low molecular weight methylcellulose for exenatide and FGF 21 delivery to treat types 1 and 2 diabetes.

    Science.gov (United States)

    Kim, Jang Kyoung; Yoo, Changhun; Cha, Yong-Hoon; Kim, Yong-Hee

    2014-11-28

    Diabetes is the fastest growing metabolic disease that fails to utilize glucose properly due to insulin deficiency or insulin resistance. Although several limited studies demonstrated non-invasive means of protein delivery, major hurdles for commercial success such as short half-life, enzymatic degradation and low bioavailability still remain to overcome. Methylcellulose (MC), a hydrophobically-modified cellulose derivative, forms temperature reversible gel in aqueous solution. However, as the gelling temperature of MC is higher than body temperature, it should be lowered to below body temperature for practical clinical application. In order to decrease gelling temperature and increase bio-compatibility and bio-elimination of MC, the molecular weight of MC was decreased using enzymatic degradation method and confirmed by gel permeation chromatography. Bio-elimination of low molecular weight (LMw) MC was confirmed with non-invasive live image and ex vivo experiment. The exenatide and FGF 21 were physically loaded 100% into LMwMC-based thermo-reversible gel and slowly released from gel with no initial bursts. Exenatide-loaded LMwMC gel showed reduction of blood glucose level for a week in type 1 diabetic animal model. FGF 21-loaded LMwMC gel reduced glucose level to normal condition and maintained over 10 days in type 2 diabetic animal model. LMwMC-based thermo-reversible and injectable hydrogel provides a strong potential to be efficient protein drug delivery system for the treatment of type 1 and type 2 diabetes. Copyright © 2014 Elsevier B.V. All rights reserved.

  20. Pathological changes in the retina of eyes rats with experimental 2 type diabetes mellitus and their correction by oral gels with biologically active substances

    Directory of Open Access Journals (Sweden)

    V. V. Vit

    2014-07-01

    Full Text Available Purpose: To study of therapeutic and prophylactic action on the retina of rats with experimental diabetes mellitus type 2 (DM2 oral mucosal gels containing biologically active substances (BAS.Methods: DM2 was induced by protamine method Ulyanov and Tarasova [2000]. As BAS used lysozyme, flour of grape leaves, the water extract of blueberries and quercetin. Mucosal gels containing active substances, applied to the mucous lining of the mouth for 2 weeks. The serum glucose concentration was performed and histological studies of the retina.Results: Application mucosal gels reduces BAS 8‑22 % glucose (most with blueberry extract and significantly improves retinal histology (vacuolar degeneration less pronounced ganglion cells, there are no structural changes in photoreceptor layer. Gels revealed more effective with containing extract of bilberry, grape flour and quercetin.Conclusion: Oral mucosal application of gels containing active substances, have protection of retina in diabetes mellitus type 2.

  1. Generating Palladium Nanoclusters Inside Very Lipophilic Gel-Type Functional Resins: Preliminary Catalytic Tests in the Hydrogenation of 2-Ethyl-Anthraquinone to 2-Ethylanthrahydroquinone

    Czech Academy of Sciences Publication Activity Database

    Bombi, G.; Lora, S.; Zancato, M.; D'Archivio, A. A.; Jeřábek, Karel; Corain, B.

    2003-01-01

    Roč. 194, 1-2 (2003), s. 273-281 ISSN 1381-1169 Institutional research plan: CEZ:AV0Z4072921 Keywords : palladium nanoclusters * gel-type resins * catalyst Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 2.264, year: 2003

  2. Nanoclustered Palladium(0) Supported on a Gel-Type Poly-acrylonitrile–N,N-dimethylacrylamide–ethylenedimethacrylate Resin: Nanostructural Aspects and Catalytic Behaviour.

    Czech Academy of Sciences Publication Activity Database

    De Zan, L.; Gasparovičová, D.; Králik, M.; Centomo, P.; Carraro, M.; Campestrini, S.; Jeřábek, Karel; Corain, B.

    2007-01-01

    Roč. 265, 1-2 (2007) , s. 1-8 ISSN 1381-1169 Institutional research plan: CEZ:AV0Z40720504 Keywords : gel- type resin s * poly-acrylonitrile * hydtogenation and oxidation catalyst Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 2.707, year: 2007

  3. Molecular Typing of Mycobacterium intracellulare Using Pulsed-Field Gel Electrophoresis, Variable-Number Tandem-Repeat Analysis, Mycobacteria Interspersed Repetitive-Unit-Variable-Number Tandem Repeat Typing, and Multilocus Sequence Typing: Molecular Characterization and Comparison of Each Typing Methods.

    Science.gov (United States)

    Jeon, Semi; Lim, Nara; Kwon, Seungjik; Shim, Taesun; Park, Misun; Kim, Bum-Joon; Kim, Seonghan

    2014-06-01

    Mycobacterium intracellulare is the major causative agent of nontuberculous mycobacteria-related pulmonary infections. The strain typing of M. intracellulare is important for the treatment and control of its infections. We compared the discrimination capacity and effective value of four different molecular typing methods. Antibiotic susceptibility testing, hsp65 and rpoB sequencing, pulsed-field gel electrophoresis (PFGE), multilocus sequence typing (MLST), mycobacteria interspersed repetitive-unit-variable-number tandem-repeat analysis (MIRU-VNTR), and VNTR assay targeting 44 M. intracellulare isolates obtained from patients with pulmonary infections were performed. All the antibiotic susceptibility patterns had no association with the molecular and sequence types tested in this study; however, the molecular and sequence types were related with each other. PFGE gave best results for discriminatory capacity, followed by VNTR, MLST, and MIRU-VNTR. The high discriminatory power of PFGE, VNTR, and MLST is enough for differentiating between reinfection and relapse, as well as for other molecular epidemiological usages. The MLST could be regarded as a representative classification method, because it showed the clearest relation with the sequence types.

  4. Thermoresponsive Gels

    Directory of Open Access Journals (Sweden)

    M. Joan Taylor

    2017-01-01

    Full Text Available Thermoresponsive gelling materials constructed from natural and synthetic polymers can be used to provide triggered action and therefore customised products such as drug delivery and regenerative medicine types as well as for other industries. Some materials give Arrhenius-type viscosity changes based on coil to globule transitions. Others produce more counterintuitive responses to temperature change because of agglomeration induced by enthalpic or entropic drivers. Extensive covalent crosslinking superimposes complexity of response and the upper and lower critical solution temperatures can translate to critical volume temperatures for these swellable but insoluble gels. Their structure and volume response confer advantages for actuation though they lack robustness. Dynamic covalent bonding has created an intermediate category where shape moulding and self-healing variants are useful for several platforms. Developing synthesis methodology—for example, Reversible Addition Fragmentation chain Transfer (RAFT and Atomic Transfer Radical Polymerisation (ATRP—provides an almost infinite range of materials that can be used for many of these gelling systems. For those that self-assemble into micelle systems that can gel, the upper and lower critical solution temperatures (UCST and LCST are analogous to those for simpler dispersible polymers. However, the tuned hydrophobic-hydrophilic balance plus the introduction of additional pH-sensitivity and, for instance, thermochromic response, open the potential for coupled mechanisms to create complex drug targeting effects at the cellular level.

  5. Low-temperature perovskite-type cadmium titanate thin films derived from a simple particulate sol-gel process

    Energy Technology Data Exchange (ETDEWEB)

    Mohammadi, M.R. [Department of Materials Science and Metallurgy, University of Cambridge, Pembroke Street, Cambridge CB2 3QZ (United Kingdom); Department of Materials Science and Engineering, Sharif University of Technology, Azadi Street, Tehran (Iran, Islamic Republic of)], E-mail: mrm41@cam.ac.uk; Fray, D.J. [Department of Materials Science and Metallurgy, University of Cambridge, Pembroke Street, Cambridge CB2 3QZ (United Kingdom)

    2009-02-15

    Low-temperature perovskite-type cadmium titanate (CdTiO{sub 3}) with a nanocrystalline and mesoporous structure was prepared at various Ti:Cd molar ratios by a straightforward particulate sol-gel route. The prepared sols had a narrow particle size distribution, in the range 23-26 nm. X-ray diffraction and Fourier transform infrared spectroscopy revealed that the powders contained a mixture of ilmenite-CdTiO{sub 3}, perovskite-CdTiO{sub 3}, anatase and rutile phases, depending on the annealing temperature and the Ti:Cd molar ratio. Perovskite-CdTiO{sub 3} was the major type obtained from cadmium-prominent powders at low temperature, whereas ilmenite-CdTiO{sub 3} was the major type obtained from titanium-prominent powders at high temperature. It was observed that the anatase-to-rutile phase transformation accelerated with decreasing Ti:Cd molar ratio. Furthermore, the ilmenite-to-perovskite phase transformation accelerated with a decrease in both the Ti:Cd molar ratio and the annealing temperature. The crystallite sizes of the ilmenite- and perovskite-CdTiO{sub 3} phases reduced with increasing the Ti:Cd molar ratio. Field emission scanning electron microscopic analysis revealed that the average grain size of the thin films decreased with an increase in the Ti:Cd molar ratio. Moreover, atomic force microscope images showed that CdTiO{sub 3} thin films had a columnar-like morphology. Based on Brunauer-Emmett-Taylor analysis, cadmium titanate powder containing Ti:Cd = 75:25 showed the greatest surface area and roughness and the smallest pore size among all the powders annealed at 500 deg. C. This is one of the smallest crystallite sizes and largest surface areas reported in the literature, and can be used in many applications in areas from optical electronics to gas sensors.

  6. Population Genetic Structure of Listeria monocytogenes Strains as Determined by Pulsed-Field Gel Electrophoresis and Multilocus Sequence Typing

    Science.gov (United States)

    Henri, Clémentine; Félix, Benjamin; Guillier, Laurent; Leekitcharoenphon, Pimlapas; Michelon, Damien; Mariet, Jean-François; Aarestrup, Frank M.; Mistou, Michel-Yves; Hendriksen, René S.

    2016-01-01

    ABSTRACT Listeria monocytogenes is a ubiquitous bacterium that may cause the foodborne illness listeriosis. Only a small amount of data about the population genetic structure of strains isolated from food is available. This study aimed to provide an accurate view of the L. monocytogenes food strain population in France. From 1999 to 2014, 1,894 L. monocytogenes strains were isolated from food at the French National Reference Laboratory for L. monocytogenes and classified according to the five risk food matrices defined by the European Food Safety Authority (EFSA). A total of 396 strains were selected on the basis of different pulsed-field gel electrophoresis (PFGE) clusters, serotypes, and strain origins and typed by multilocus sequence typing (MLST), and the MLST results were supplemented with MLST data available from Institut Pasteur, representing human and additional food strains from France. The distribution of sequence types (STs) was compared between food and clinical strains on a panel of 675 strains. High congruence between PFGE and MLST was found. Out of 73 PFGE clusters, the two most prevalent corresponded to ST9 and ST121. Using original statistical analysis, we demonstrated that (i) there was not a clear association between ST9 and ST121 and the food matrices, (ii) serotype IIc, ST8, and ST4 were associated with meat products, and (iii) ST13 was associated with dairy products. Of the two major STs, ST121 was the ST that included the fewest clinical strains, which might indicate lower virulence. This observation may be directly relevant for refining risk analysis models for the better management of food safety. IMPORTANCE This study showed a very useful backward compatibility between PFGE and MLST for surveillance. The results enabled better understanding of the population structure of L. monocytogenes strains isolated from food and management of the health risks associated with L. monocytogenes food strains. Moreover, this work provided an accurate view

  7. Comparison of multilocus sequence typing and pulsed-field gel electrophoresis for Salmonella spp. identification in surface water

    Science.gov (United States)

    Kuo, Chun Wei; Hao Huang, Kuan; Hsu, Bing Mu; Tsai, Hsien Lung; Tseng, Shao Feng; Kao, Po Min; Shen, Shu Min; Chou Chiu, Yi; Chen, Jung Sheng

    2013-04-01

    Salmonella is one of the most important pathogens of waterborne diseases with outbreaks from contaminated water reported worldwide. In addition, Salmonella spp. can survive for long periods in aquatic environments. To realize genotypes and serovars of Salmonella in aquatic environments, we isolated the Salmonella strains by selective culture plates to identify the serovars of Salmonella by serological assay, and identify the genotypes by Multilocus sequence typing (MLST) based on the sequence data from University College Cork (UCC), respectively. The results show that 36 stream water samples (30.1%) and 18 drinking water samples (23.3%) were confirmed the existence of Salmonella using culture method combined PCR specific invA gene amplification. In this study, 24 cultured isolates of Salmonella from water samples were classified to fifteen Salmonella enterica serovars. In addition, we construct phylogenetic analysis using phylogenetic tree and Minimum spanning tree (MST) method to analyze the relationship of clinical, environmental, and geographical data. Phylogenetic tree showed that four main clusters and our strains can be distributed in all. The genotypes of isolates from stream water are more biodiversity while comparing the Salmonella strains genotypes from drinking water sources. According to MST data, we can found the positive correlation between serovars and genotypes of Salmonella. Previous studies revealed that the result of Pulsed field gel electrophoresis (PFGE) method can predict the serovars of Salmonella strain. Hence, we used the MLST data combined phylogenetic analysis to identify the serovars of Salmonella strain and achieved effectiveness. While using the geographical data combined phylogenetic analysis, the result showed that the dominant strains were existed in whole stream area in rainy season. Keywords: Salmonella spp., MLST, phylogenetic analysis, PFGE

  8. A new psoralen-containing gel for topical PUVA therapy: development, and treatment results in patients with palmoplantar and plaque-type psoriasis, and hyperkeratotic eczema

    Energy Technology Data Exchange (ETDEWEB)

    De Rie, M.A.; Van Eendenburg, J.P.; Versnick, A.C.; Stolk, L.M.L.; Bos, J.D.; Westerhof, W. [Amsterdam Univ. (Netherlands). Academic Medical Center

    1995-06-01

    Topical photochemotherapy with psoralen and its derivatives 4,5`,8-trimethylpsoralen (TMP) and 8-methoxypsoralen (8-MOP), with UVA irradiation, was evaluated with regard to minimum phototoxic dose, concentration, timing of UVA irradiation and systemic and local side-effects, in healthy volunteers. Psoralen (0.005%) in aqueous gel was found to be superior to TMP and 8-MOP in aqueous gel. No hyperpigmentation was seen after topical PUVA treatment with psoralen in aqueous gel. Patients with plaque-type psoriasis (n=7), palmoplantar psoriasis (n=7) and hyperkeratotic eczema (n=2) were treated. Topical PUVA therapy was effective in most psoriasis patients, without the occurrence of local or systemic side-effects. Moreover, hyperkeratotic eczema patients who did not respond to conventional therapy showed partial remission. These results indicate that topical PUVA therapy with psoralen in aqueous gel is a useful therapeutic modality for treatment of psoriasis patients, and patients with recalcitrant dermatoses such as palmoplantar psoriasis and hyperkeratotic eczema. (author).

  9. A new psoralen-containing gel for topical PUVA therapy: development, and treatment results in patients with palmoplantar and plaque-type psoriasis, and hyperkeratotic eczema

    International Nuclear Information System (INIS)

    De Rie, M.A.; Van Eendenburg, J.P.; Versnick, A.C.; Stolk, L.M.L.; Bos, J.D.; Westerhof, W.

    1995-01-01

    Topical photochemotherapy with psoralen and its derivatives 4,5',8-trimethylpsoralen (TMP) and 8-methoxypsoralen (8-MOP), with UVA irradiation, was evaluated with regard to minimum phototoxic dose, concentration, timing of UVA irradiation and systemic and local side-effects, in healthy volunteers. Psoralen (0.005%) in aqueous gel was found to be superior to TMP and 8-MOP in aqueous gel. No hyperpigmentation was seen after topical PUVA treatment with psoralen in aqueous gel. Patients with plaque-type psoriasis (n=7), palmoplantar psoriasis (n=7) and hyperkeratotic eczema (n=2) were treated. Topical PUVA therapy was effective in most psoriasis patients, without the occurrence of local or systemic side-effects. Moreover, hyperkeratotic eczema patients who did not respond to conventional therapy showed partial remission. These results indicate that topical PUVA therapy with psoralen in aqueous gel is a useful therapeutic modality for treatment of psoriasis patients, and patients with recalcitrant dermatoses such as palmoplantar psoriasis and hyperkeratotic eczema. (author)

  10. Shigella sonnei biotype g carrying class 2 integrons in southern Italy: a retrospective typing study by pulsed field gel electrophoresis

    Directory of Open Access Journals (Sweden)

    Romani Cristina

    2006-07-01

    Full Text Available Abstract Background Emergence and global dissemination of multiresistant strains of enteric pathogens is a very concerning problem from both epidemiological and Public Health points of view. Shigella sonnei is the serogroup of Shigella most frequently responsible for sporadic and epidemic enteritis in developed countries. The dissemination is associated most often to human to human transmission, but foodborne episodes have also been described. In recent years the circulation of multiresistant strains of S. sonnei biotype g carrying a class 2 integron has been reported in many countries worldwide. In southern Italy a strain with similar properties has been responsible for a large community outbreak occurred in 2003 in Palermo, Sicily. The objective of this study was to date the emergence of the biotype g strain carrying the class 2 integron in southern Italy and to evaluate the genetic heterogeneity of biotype g S. sonnei isolated throughout an extended interval of time. Methods A total of 31 clinical isolates of S. sonnei biotype g identified in southern Italy during the years 1971–2000 were studied. The strains were identified at the serogroup level, characterized by biochemical tests and submitted to antimicrobial susceptibility testing. Molecular typing was performed by pulsed field gel electrophoresis (PFGE after digestion of DNA by XbaI. Carriage of class 2 integrons was investigated by polymerase chain reaction (PCR with specific primers and confirmed by restriction endonuclease analysis of amplicons. Results The 15 isolates of S. sonnei biotype g identified in the decade 1971–1980 showed highly heterogeneous drug resistance profiles and pulsotypes. None of the isolates was simultaneous resistant to streptomycin and trimethoprim and none was class 2 integron positive. On the contrary, this resistance phenotype and class 2 integron carriage were very common among the 16 strains of biotype g identified in the following two decades

  11. Emergence of a mutL Mutation Causing Multilocus Sequence Typing-Pulsed-Field Gel Electrophoresis Discrepancy among Pseudomonas aeruginosa Isolates from a Cystic Fibrosis Patient

    OpenAIRE

    Garcia-Castillo, M.; Maiz, L.; Morosini, M.-I.; Rodriguez-Banos, M.; Suarez, L.; Fernandez-Olmos, A.; Baquero, F.; Canton, R.; del Campo, R.

    2012-01-01

    A multilocus sequence type (MLST) shift (from ST242 to ST996) was detected in Pseudomonas aeruginosa isolates with a uniform pulsed-field gel electrophoresis (PFGE) pattern obtained from a chronically colonized patient. MLST mutational change involved the mutL gene with the consequent emergence of a hypermutable phenotype. This observation challenges the required neutrality of mutL as an appropriate marker in MLST and alerts researchers to the limitations of MLST-only-based population studies...

  12. A steroid-based gelator of A(LS)(2) type: tuning gel properties by metal coordination

    Czech Academy of Sciences Publication Activity Database

    Svobodová, Hana; Nonappa, J.; Lathinen, M.; Wimmer, Zdeněk; Kolehmainen, E.

    2012-01-01

    Roč. 8, č. 30 (2012), s. 3840-3847 ISSN 1744-683X Institutional research plan: CEZ:AV0Z50380511 Keywords : DIPICOLINIC ACID * SUPRAMOLECULAR GELS * CHEMISTRY Subject RIV: CE - Biochemistry Impact factor: 3.909, year: 2012

  13. New type of gel polymer electrolytes based on selected methacrylates and their characteristics. Part II. fluorinated co-polymers

    Czech Academy of Sciences Publication Activity Database

    Michálek, Jiří; Abbrent, Sabina; Musil, M.; Kovářová, Jana; Hodan, Jiří; Dybal, Jiří

    2016-01-01

    Roč. 208, 1 August (2016), s. 211-224 ISSN 0013-4686 R&D Projects: GA ČR(CZ) GAP102/10/2091 Institutional support: RVO:61389013 Keywords : gel polymer electrolytes * thermal analysis * ionic conductivity Subject RIV: CG - Electrochemistry Impact factor: 4.798, year: 2016

  14. Effect of Topical Tetracycline Gel with Non Surgical Periodontal Therapy on Hba1c and Lipid Profile in Type 2 Diabetic Patients: A Clinico- Biochemical Study

    Directory of Open Access Journals (Sweden)

    A Haerian-Ardakani

    2014-11-01

    Full Text Available Introduction: The present study aimed to evaluate the Effect of topical tetracycline gel application with non surgical periodontal therapy on HbA1c and lipid profile in type 2 diabetic patients. Methods: A total of 30 type 2 diabetic patients were randomly divided into two groups. The first group received scaling and root planning, whereas the second group received scaling and root planning with topically applied tetracycline gel. Clinical factors such as GI, PI, PPD and biochemical factors such as HbA1c and lipid profile were assessed in beginning of study and 3 months later. Results: Comparing the clinical factors between the two groups revealed that periodontal pocket depth significantly reduced in tetracycline-received group. Regarding the biochemical factors, triglyceride levels decreased significantly in tetracycline-received group. No significant difference was observed between the two groups in regard with other clinical and biochemical factors. Conclusion: The study findings demonstrated that clinical and biochemical parameters have been improved after non surgical periodontal treatment in both groups. Although it seems that application of topical tetracycline gel combined with non-surgical periodontal therapy is effective in improvement of some clinical and biochemical factors like PPD and TG, it doesn’t offer any superiority in regard with other factors compared to mere non surgical periodontal therapy.

  15. The clinical and metabolic effects of subgingival application of xanthan-based chlorhexidine gel in Type 2 diabetic patients with chronic periodontitis

    Science.gov (United States)

    Faramarzi, Masoumeh; Shirmohammadi, Adileh; Chitsazi, Mohammadtaghi; Shamami, Mehrnoosh Sadighi; Ghanitab, Sahand

    2017-01-01

    Background: There is a two-way relationship between periodontal disease and diabetes. The purpose of this study was to evaluate the clinical and metabolic effects of a xanthan-based chlorhexidine (CHX) gel used as an adjunct to nonsurgical periodontal therapy in Type II diabetic patients with chronic periodontitis. Materials and Methods: Sixty-eight diabetic patients with moderate to advanced periodontitis and glycated hemoglobin (HbA1c) ≥6% were selected. The test group (n = 34) received scaling and root planning (SRP) plus xanthan-based CHX gel. The control group (n = 34) received single SRP. Fasting blood sugar (FBS) and HbA1c tests were done at the baseline and after 3 and 6 months. Data from the study were analyzed using descriptive statistics (mean ± standard deviation and frequency), ANOVA test by SPSS.15 software (SPSS Inc. Chicago, IL, USA). P periodontal treatment in diabetic patients with periodontitis. PMID:29109743

  16. Molecular typing of vancomycin-resistant Enterococcus faecium with an automated repetitive sequence-based PCR microbial typing system compared with pulsed-field gel electrophoresis and multilocus sequence typing.

    Science.gov (United States)

    Kardén-Lilja, Minna; Vuopio, Jaana; Koskela, Markku; Tissari, Päivi; Salmenlinna, Saara

    2013-05-01

    Pulsed-field gel electrophoresis (PFGE) is the main typing method used for the molecular typing of vancomycin-resistant Enterococcus faecium (VREfm). However, more rapid and unambiguous typing methods are needed. DiversiLab, a repetitive sequence-based PCR (rep-PCR), offers an alternative method for strain typing. Thirty-nine VREfm isolates with known epidemiological relationships were characterized by semi-automated rep-PCR (DiversiLab), PFGE, and multilocus sequence typing (MLST). The DiversiLab results were analysed in 2 ways: first relying solely on the DiversiLab software, and second by DiversiLab analysis combined with manual interpretation. The analysis with interpretation yielded more DiversiLab profiles, correlated better with PFGE and MLST, and grouped the isolates better according to their relatedness in time and space. However, most of the DiversiLab groups also included isolates with different PFGE and MLST types. DiversiLab provides rapid information when investigating a potential hospital outbreak. However, the interpretation of E. faecium DiversiLab results cannot be fully automated and is not always straightforward. Other typing methods may be necessary to confirm the analysis.

  17. Enhanced discrimination of highly clonal ST22-methicillin-resistant Staphylococcus aureus IV isolates achieved by combining spa, dru, and pulsed-field gel electrophoresis typing data.

    LENUS (Irish Health Repository)

    Shore, Anna C

    2010-05-01

    ST22-methicillin-resistant Staphylococcus aureus type IV (ST22-MRSA-IV) is endemic in Irish hospitals and is designated antibiogram-resistogram type-pulsed-field group (AR-PFG) 06-01. Isolates of this highly clonal strain exhibit limited numbers of pulsed-field gel electrophoresis (PFGE) patterns and spa types. This study investigated whether combining PFGE and spa typing with DNA sequencing of the staphylococcal cassette chromosome mec element (SCCmec)-associated direct repeat unit (dru typing) would improve isolate discrimination. A total of 173 MRSA isolates recovered in one Irish hospital during periods in 2007 and 2008 were investigated using antibiogram-resistogram (AR), PFGE, spa, dru, and SCCmec typing. Isolates representative of each of the 17 pulsed-field group 01 (PFG-01) spa types identified underwent multilocus sequence typing, and all isolates were ST22. Ninety-seven percent of isolates (168 of 173) exhibited AR-PFG 06-01 or closely related AR patterns, and 163 of these isolates harbored SCCmec type IVh. The combination of PFGE, spa, and dru typing methods significantly improved discrimination of the 168 PFG-01 isolates, yielding 65 type combinations with a Simpson\\'s index of diversity (SID) of 96.53, compared to (i) pairwise combinations of spa and dru typing, spa and PFGE typing, and dru and PFGE typing, which yielded 37, 44, and 43 type combinations with SIDs of 90.84, 91.00, and 93.57, respectively, or (ii) individual spa, dru, and PFGE typing methods, which yielded 17, 17, and 21 types with SIDs of 66.9, 77.83, and 81.34, respectively. Analysis of epidemiological information for a subset of PFG-01 isolates validated the relationships inferred using combined PFGE, spa, and dru typing data. This approach significantly enhances discrimination of ST22-MRSA-IV isolates and could be applied to epidemiological investigations of other highly clonal MRSA strains.

  18. Studies of techniques for the post-elution concentration of 99mTc obtained from gel type 99Mo/99mTc generators

    International Nuclear Information System (INIS)

    Suzuki, Katia Noriko

    2009-01-01

    On average 80% of the radiopharmaceuticals used in Nuclear Medicine are labeled with 99 mTc due to its physical properties and easy attainment through of 99 Mo/ 99 mTc generators. The Directory of Radiopharmacy (DIRF) of IPEN-CNEN/SP developed a gel type chromatographic generator of MoZr with 99 Mo produced by 98 Mo(n,γ) 99 Mo reaction that occurs at the IEA-R1 Nuclear Reactor. The gel is composed of zirconium molybdate with elution volume of 12 mL with an activity of 11100 MBq (300 mCi) producing a radioactive concentration of 925 MBq (25 mCi)/mL. The fission generator gives a higher radioactive concentration around 1850 MBq (50 mCi)/mL. The aim of this work is to study a system of post-elution concentration of 99 mTc for the attainment of a high enough radioactive concentration to meet the demands of the market, with a proved quality. Two types of systems of post-elution concentration were developed: the single and the tandem. The most appropriate system for the gel generator of 99 Mo/ 99 mTc, being at the same time sterile and vacuum automated, was the tandem system using Dionex 2.5 cc/QMA cartridges. The gel generator is eluted with 10 mL of solution of 0.1% NaCl and the pertechnetate anion is retained in the QMA cartridge and further eluted with 4 mL of saline. The process takes no more than 30 minutes. The elution efficiency of the system of concentration was 90 %. At the beginning of 2009 a global crisis in the supply of 99 Mo took place making it necessary the development of alternative technologies for the production of 99 Mo/ 99 mTc generators using fission produced 99 Mo and the development of an appropriate method to extend the useful life of this generator. The results of this study showed that the same system developed for the post- concentration of the gel generator can be employed for the fission generator, using the tandem system, giving a concentration factor of 3 for the elution of 99 mTc. (author)

  19. Polyacrylamide gel electrophoresis of RNA.

    Science.gov (United States)

    Rio, Donald C; Ares, Manuel; Hannon, Gregory J; Nilsen, Timothy W

    2010-06-01

    Perhaps the most important and certainly the most often used technique in RNA analysis is gel electrophoresis. This technique is generally applicable for RNA detection, quantification, purification by size, and quality assessment. Because RNAs are negatively charged, they migrate toward the anode in the presence of electric current. The gel acts as a sieve to selectively impede the migration of the RNA in proportion to its mass, given that its mass is generally proportional to its charge. Because mass is approximately related to chain length, the length of an RNA is more generally determined by its migration. In addition, topology (i.e., circularity) can affect migration, making RNAs appear longer on the gel than they actually are. Gels are used in a wide variety of techniques, including Northern blotting, primer extension, footprinting, and analyzing processing reactions. They are invaluable as preparative and fractionating tools. There are two common types of gel: polyacrylamide and agarose. For most applications, denaturing acrylamide gels are most appropriate. These gels are extremely versatile and can resolve RNAs from ~600 to RNA-protein complexes, native gels are appropriate. The only disadvantage to acrylamide gels is that they are not suitable for analyzing large RNAs (> or =600 nt); for such applications, agarose gels are preferred. This protocol describes how to prepare, load, and run polyacrylamide gels for RNA analysis.

  20. Ferroelectric lanthanum-substituted Bi4Ti3O12 thin films fabricated on p-type Si(100) substrates by a sol-gel method

    International Nuclear Information System (INIS)

    Bae, Ji Cheul; Kim, Sang Su; Kim, Won-Jeong; Choi, Eun Kyung; Song, Tae Kwon

    2004-01-01

    Bi 3.25 La 0.75 Ti 3 O 12 (BLT) thin films have been successfully fabricated on p-type Si(100) substrates by a sol-gel spin-coating method. The microstructures and surface morphologies of the BLT thin films on p-type Si(100) substrates annealed at 700 deg. C for 30 min in oxygen atmosphere were examined by an X-ray diffractometer and a scanning electron microscope, respectively. The BLT/p-type Si(100) capacitors annealed at 700 deg. C for 30 min exhibit good capacitance-voltage (C-V) characteristics and large memory window of approximately 6 V with a sweep voltage of ±16 V. From the frequency dependency of C-V characteristics of the BLT/p-type Si(100) capacitors, the fixed charge density (N fc ) at the interface of BLT/p-type Si(100) was calculated as approximately 1.24x10 12 /cm 2 . The humps and valleys observed in C-V curves were interpreted by introducing the electron charge injection and barrier-lowering effect at the interface of BLT/p-type Si(100). Based on the voltage and the frequency dependent C-V measurements, the memory windows of BLT/p-type Si(100) capacitor are significantly influenced by the electron charge injection and polarization reverse

  1. Optical investigation of Tb{sup 3+}-doped Y{sub 2}O{sub 3} nanocrystals prepared by Pechini-type sol-gel process

    Energy Technology Data Exchange (ETDEWEB)

    Back, M., E-mail: m.back@hotmail.it; Massari, A.; Boffelli, M.; Gonella, F.; Riello, P.; Cristofori, D. [Universita Ca' Foscari di Venezia and INSTM, Dipartimento di Scienze Molecolari e Nanosistemi (Italy); Ricco, R.; Enrichi, F., E-mail: enrichi@civen.org [CIVEN (Coordinamento Interuniversitario Veneto per le Nanotecnologie) (Italy)

    2012-03-15

    We report an optical study of Tb{sup 3+}-doped Y{sub 2}O{sub 3} nanocrystals synthesized by Pechini-type sol-gel method. The particles are investigated in terms of size and morphology by means of X-ray diffraction and transmission electron microscopy analysis. It is shown how the simple Pechini method allows for the growth of monocrystalline nanoparticles with a volume-weighted average size of about 30 nm. The optical properties of Tb{sup 3+} in the host lattice are studied in terms of PL, PLE, and lifetimes. Moreover, a correlation between the type of decay curves, the emission and excitation bands' shapes, and the site location of the emitting Tb{sup 3+} in the host material Y{sub 2}O{sub 3} is proposed.

  2. Gelatin increases the coarseness of whey protein gels and impairs water exudation from the mixed gel at low temperatures

    NARCIS (Netherlands)

    Martin, A.H.; Bakhuizen, E.; Ersch, C.; Urbonaite, V.; Jongh, H.H.J. de; Pouvreau, L.

    2016-01-01

    To understand the origin of water holding of mixed protein gels, a study was performed on water exudation from mixed whey protein (WP)-gelatin gels upon applied pressure. Mixed gels were prepared with varying WP and gelatin concentration and gelatin type to obtain gels with a wide range of gel

  3. Considerations on a sol-gel type process as a fuel fabrication route for the actinide recycle

    International Nuclear Information System (INIS)

    Facchini, A.G.; Gallone, S.; Zamorani, E.

    1980-01-01

    The technology based on the powder pelletizing faces relevant difficulties, when used to fabricate both targets and fuels containing transplutonium elements. The applicability of the Gel-Supported Precipitation process (GSP) as an alternative, has been examined on the ground of the know-how gained in producing U-Pu mixed oxide microspheres or granules suitable for pressing. The applicability of the process has been examined on the basis of the following factors: - the properties of the actinide solutions obtained through the HAW partitioning; - the target and fuel element composition and geometry which must be met in order to perform a homogeneous or a heterogeneous recycle in the FBR's and in the LWR's; - the actinide radiolytical effects on the compounds used to produce either microspheres or granules; - the criticality aspects. This paper shall be considered as a first attempt only; how ever, it can be useful in evaluating the different alternatives from the GSP fabrication standpoint. Moreover, some areas for further experimental research are indicated to confirm the applicability of the GSP process

  4. Synthesis behavior and magnetic properties of Mg-Ni co-doped Y-type hexaferrite prepared by sol-gel auto-combustion method

    Energy Technology Data Exchange (ETDEWEB)

    Alizad Farzin, Y., E-mail: y.alizadfarzin@ut.ac.ir [School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, P.O. Box 14395-553, Tehran (Iran, Islamic Republic of); Mirzaee, O. [Department of Materials Science and Engineering, University of Semnan (Iran, Islamic Republic of); Ghasemi, A. [Department of Materials Engineering, Malek Ashtar University of Technology (Iran, Islamic Republic of)

    2016-08-01

    Nano crystalline Y-type hexaferrites with chemical composition of Sr{sub 2}Co{sub 2−x}Mg{sub x/2}Ni{sub x/2}Fe{sub 12}O{sub 22} (x of 0–0.6) were prepared by sol-gel auto-combustion technique at the temperature ranging from 900 to 1150 °C. The prepared samples were characterized by differential thermal analysis (DTA), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy dispersive spectrometer (EDS), and vibrating sample magnetometer (VSM). The results demonstrated that single phase co-doped Y-type hexaferrites with space group of R3/m were prepared at 1000 °C and crystallite size of the samples was calculated in the range of 45–63 nm. Also, below this temperature, some intermediate phases such as hematite, spinel ferrite, and SrO were observed. All of the synthesized hexaferrites showed homogeneous distribution and hexagonal platelet-like shapes which were suitable for microwave absorption. Hysteresis loop measurements revealed that the presence of hematite as a second phase caused a reduction in the saturation magnetization. Moreover, it was observed that, with increasing the calcination temperature to above 1000 °C, saturation magnetization demonstrated no significant changes while coercivity reduced from 950 to 250 Oe, which was due to transition from single to multi domain structures. - Highlights: • Nano crystalline Y-type hexaferrites has been synthesized via sol-gel auto combustion method. • Effect of Ni and Mg ions on synthesis behavior and magnetic properties of Co{sub 2}Y hexaferrite was investigated. • Thermal behavior of Mg ions caused reduction in synthesis temperature to 950 °C. • Average thickness of particles has been decreased by the increase of Mg and Ni ions. • The coercivity strongly decreased with increasing of calcination temperature.

  5. Molecular typing of Mycobacterium kansasii using pulsed-field gel electrophoresis and a newly designed variable-number tandem repeat analysis.

    Science.gov (United States)

    Bakuła, Zofia; Brzostek, Anna; Borówka, Paulina; Żaczek, Anna; Szulc-Kiełbik, Izabela; Podpora, Agata; Parniewski, Paweł; Strapagiel, Dominik; Dziadek, Jarosław; Proboszcz, Małgorzata; Bielecki, Jacek; van Ingen, Jakko; Jagielski, Tomasz

    2018-03-13

    Molecular epidemiological studies of Mycobacterium kansasii are hampered by the lack of highly-discriminatory genotyping modalities. The purpose of this study was to design a new, high-resolution fingerprinting method for M. kansasii. Complete genome sequence of the M. kansasii ATCC 12478 reference strain was searched for satellite-like repetitive DNA elements comprising tandem repeats. A total of 24 variable-number tandem repeat (VNTR) loci were identified with potential discriminatory capacity. Of these, 17 were used to study polymorphism among 67 M. kansasii strains representing six subtypes (I-VI). The results of VNTR typing were compared with those of pulsed-field gel electrophoresis (PFGE) with AsnI digestion. Six VNTRs i.e. (VNTR 1, 2, 8, 14, 20 and 23) allow to differentiate analyzed strains with the same discriminatory capacities as use of a 17-loci panel. VNTR typing and PFGE in conjunction revealed 45 distinct patterns, including 11 clusters with 33 isolates and 34 unique patterns. The Hunter-Gaston's discriminatory index was 0.95 and 0.66 for PFGE and VNTR typing respectively, and 0.97 for the two methods combined. In conclusion, this study delivers a new typing scheme, based on VNTR polymorphism, and recommends it as a first-line test prior to PFGE analysis in a two-step typing strategy for M. kansasii.

  6. Hydride-induced amplification of performance and binding enthalpies in chromium hydrazide gels for Kubas-type hydrogen storage.

    Science.gov (United States)

    Hamaed, Ahmad; Hoang, Tuan K A; Moula, Golam; Aroca, Ricardo; Trudeau, Michel L; Antonelli, David M

    2011-10-05

    Hydrogen is the ideal fuel because it contains the most energy per gram of any chemical substance and forms water as the only byproduct of consumption. However, storage still remains a formidable challenge because of the thermodynamic and kinetic issues encountered when binding hydrogen to a carrier. In this study, we demonstrate how the principal binding sites in a new class of hydrogen storage materials based on the Kubas interaction can be tuned by variation of the coordination sphere about the metal to dramatically increase the binding enthalpies and performance, while also avoiding the shortcomings of hydrides and physisorpion materials, which have dominated most research to date. This was accomplished through hydrogenation of chromium alkyl hydrazide gels, synthesized from bis(trimethylsilylmethyl) chromium and hydrazine, to form materials with low-coordinate Cr hydride centers as the principal H(2) binding sites, thus exploiting the fact that metal hydrides form stronger Kubas interactions than the corresponding metal alkyls. This led to up to a 6-fold increase in storage capacity at room temperature. The material with the highest capacity has an excess reversible storage of 3.23 wt % at 298 K and 170 bar without saturation, corresponding to 40.8 kg H(2)/m(3), comparable to the 2015 DOE system goal for volumetric density (40 kg/m(3)) at a safe operating pressure. These materials possess linear isotherms and enthalpies that rise on coverage, retain up to 100% of their adsorption capacities on warming from 77 to 298 K, and have no kinetic barrier to adsorption or desorption. In a practical system, these materials would use pressure instead of temperature as a toggle and can thus be used in compressed gas tanks, currently employed in the majority of hydrogen test vehicles, to dramatically increase the amount of hydrogen stored, and therefore range of any vehicle.

  7. Characterization of wild-type human medium-chain acyl-CoA dehydrogenase (MCAD) and mutant enzymes present in MCAD-deficient patients by two-dimensional gel electrophoresis

    DEFF Research Database (Denmark)

    Bross, P; Jensen, T G; Andresen, B S

    1994-01-01

    Two-dimensional gel electrophoresis was used to study and compare wild-type medium-chain acyl-CoA dehydrogenase (MCAD; EC 1.3.99.3) and mis-sense mutant enzyme found in patients with MCAD deficiency. By comparing the patterns for wild-type and mutant MCAD expressed in Escherichia coli...

  8. Design and synthesis of vanadium hydrazide gels for Kubas-type hydrogen adsorption: a new class of hydrogen storage materials.

    Science.gov (United States)

    Hoang, Tuan K A; Webb, Michael I; Mai, Hung V; Hamaed, Ahmad; Walsby, Charles J; Trudeau, Michel; Antonelli, David M

    2010-08-25

    In this paper we demonstrate that the Kubas interaction, a nondissociative form of weak hydrogen chemisorption with binding enthalpies in the ideal 20-30 kJ/mol range for room-temperature hydrogen storage, can be exploited in the design of a new class of hydrogen storage materials which avoid the shortcomings of hydrides and physisorpion materials. This was accomplished through the synthesis of novel vanadium hydrazide gels that use low-coordinate V centers as the principal Kubas H(2) binding sites with only a negligible contribution from physisorption. Materials were synthesized at vanadium-to-hydrazine ratios of 4:3, 1:1, 1:1.5, and 1:2 and characterized by X-ray powder diffraction, X-ray photoelectron spectroscopy, nitrogen adsorption, elemental analysis, infrared spectroscopy, and electron paramagnetic resonance spectroscopy. The material with the highest capacity possesses an excess reversible storage of 4.04 wt % at 77 K and 85 bar, corresponding to a true volumetric adsorption of 80 kg H(2)/m(3) and an excess volumetric adsorption of 60.01 kg/m(3). These values are in the range of the ultimate U.S. Department of Energy goal for volumetric density (70 kg/m(3)) as well as the best physisorption material studied to date (49 kg H(2)/m(3) for MOF-177). This material also displays a surprisingly high volumetric density of 23.2 kg H(2)/m(3) at room temperature and 85 bar--roughly 3 times higher than that of compressed gas and approaching the DOE 2010 goal of 28 kg H(2)/m(3). These materials possess linear isotherms and enthalpies that rise on coverage and have little or no kinetic barrier to adsorption or desorption. In a practical system these materials would use pressure instead of temperature as a toggle and can thus be used in compressed gas tanks, currently employed in many hydrogen test vehicles, to dramatically increase the amount of hydrogen stored and therefore the range of any vehicle.

  9. Sodium and potassium doped P-type ZnO films by sol-gel spin-coating technique

    Science.gov (United States)

    Au, Benedict Wen-Cheun; Chan, Kah-Yoong

    2017-07-01

    Zinc oxide (ZnO) is a promising material in a variety of applications including sensors, transistors and solar cells. Many researchers studied N-type ZnO films and reported enhanced properties. On the other hand, P-type ZnO films were rarely attempted due to the self-compensation effect. Success in achieving P-type ZnO films is important as it will pave the way for more advanced complementary devices. In this work, P-type sodium and potassium doped ZnO films were fabricated on glass substrates with doping concentration between 0 and 25 at.%. The influences of doping concentration on surface morphology, structural, optical and electrical properties were investigated using atomic force microscopy, X-ray diffraction spectroscopy, energy-dispersive X-ray spectroscopy, ultraviolet-visible (UV-Vis) spectrophotometer, photoluminescence spectroscopy and Hall-effect electrical transport measurement system. The distinctive behavior of P-type ZnO films with different doping concentrations will be discussed.

  10. Yield stress determination of a physical gel

    DEFF Research Database (Denmark)

    Hvidt, Søren

    2013-01-01

    Pluronic F127 solutions form gels in water with high elastic moduli. Pluronic gels can, however, only withstand small deformations and stresses. Different steady shear and oscillatory methods traditionally used to determine yield stress values are compared. The results show that the yield stresse...... values of these gels depend on test type and measurement time, and no absolute yield stress value can be determined for these physical gels....

  11. Transmission of endemic ST22-MRSA-IV on four acute hospital wards investigated using a combination of spa, dru and pulsed-field gel electrophoresis typing.

    LENUS (Irish Health Repository)

    Creamer, E

    2012-11-01

    The transmission of meticillin-resistant Staphylococcus aureus (MRSA) between individual patients is difficult to track in institutions where MRSA is endemic. We investigated the transmission of MRSA where ST22-MRSA-IV is endemic on four wards using demographic data, patient and environmental screening, and molecular typing of isolates. A total of 939 patients were screened, 636 within 72 h of admission (on admission) and 303 >72 h after admission, and 1,252 environmental samples were obtained. Isolates were typed by spa, dru and pulsed-field gel electrophoresis (PFGE) typing. A composite dendrogram generated from the three sets of typing data was used to divide isolates into \\'dendrogram groups\\' (DGs). Ten percent of patients (92\\/939) were MRSA-positive; 7 % (44\\/636) on admission and 16 % (48\\/303) >72 h after admission (p = 0.0007). MRSA was recovered from 5 % of environmental specimens (65\\/1,252). Most isolates from patients (97 %, 85\\/88) and the environment (97 %, 63\\/65) exhibited the ST22-MRSA-IV genotype. Four DGs (DG1, DG4, DG16 and DG17) accounted for 58 % of ST22-MRSA-IV isolates from patients. Epidemiological evidence suggested cross-transmission among 44\\/92 patients (48 %) but molecular typing confirmed probable cross-transmission in only 11 instances (13 %, 11\\/88), with the majority of cross-transmission (64 %; 7\\/11) occurring on one ward. In the setting of highly clonal endemic MRSA, the combination of local epidemiology, PFGE, spa and dru typing provided valuable insights into MRSA transmission.

  12. The pathogenic potential of different pulsed-field gel electrophoresis types of Listeria monocytogenes strains isolated from food in Northeast Bosnia and Herzegovina.

    Science.gov (United States)

    Hodžić, Snjezana; Hukić, Mirsada; Franciosa, Giovanna; Aureli, Paolo

    2011-09-01

    Listeria monocytogenes is often present in meat and meat products that are sold in the area of northeast Bosnia and Herzegovina. The major objective of this study was to examine the virulence of L. monocytogenes strains isolated from these types of food in that geographic area. Polymerase chain reaction was used to detect eight genes responsible for virulence of this pathogen, namely, prfA, inlA, inlB, hly, plcA, plcB, actA, and mpl. All examined isolates were confirmed to possess the eight virulence genes. Ten different pulsed-field gel electrophoresis (PFGE) macrorestriction profiles were recognized among 19 L. monocytogenes strains after restriction with two different endonucleases (ApaI and AscI). The pathogenicity of three different PFGE types of L. monocytogenes was confirmed through in vivo tests, which were performed on female white mice (Pasteur strain), and it ranged from 3.55 × 10(8) LD50 to 1.58 × 10(10) LD50. All of the three different PFGE types of L. monocytogenes were regarded as moderately virulent in relation to the reference strain L. monocytogenes Scott A. This result might be one of the reasons for the absence of reported listeriosis in northeast Bosnia and Herzegovina, despite the high degree of food contamination with this pathogen.

  13. Serotype specific primers and gel-based RT-PCR assays for 'typing' African horse sickness virus: identification of strains from Africa.

    Directory of Open Access Journals (Sweden)

    Narender S Maan

    Full Text Available African horse sickness is a devastating, transboundary animal disease, that is 'listed' by the Office International des Epizooties (OIE. Although attenuated, inactivated and subunit vaccines have been developed for African horse sickness virus (AHSV, these are serotype-specific and their effective deployment therefore relies on rapid and reliable identification of virus type. AHSV serotype is controlled by the specificity of interactions between neutralising antibodies, and components of the outer-capsid, particularly protein VP2 (encoded by AHSV genome segment 2 (Seg-2. We report the development and evaluation of novel gel based reverse transcription-PCR (RT-PCR assays targeting AHSV Seg-2, which can be used to very significantly increase the speed and reliability of detection and identification (compared to virus neutralisation tests of the nine serotypes of AHSV. Primer sets were designed targeting regions of Seg-2 that are conserved between strains within each of the AHSV serotype (types 1 to 9. These assays were evaluated using multiple AHSV strains from the orbivirus reference collection at IAH (www.reoviridae.org/dsRNA_virus_proteins/ReoID/AHSV-isolates.htm. In each case the Seg-2 primers showed a high level of specificity and failed to cross-amplify the most closely related heterologous AHSV types, or other related orbiviruses (such as bluetongue virus (BTV, or equine encephalosis virus (EEV. The assays are rapid and sensitive, and can be used to detect and type viral RNA in blood, tissue samples, or cultivated viral suspensions within 24 h. They were used to identify AHSV strains from recent outbreaks in sub-Saharan African countries. These methods also generate cDNAs suitable for sequencing and phylogenetic analyses of Seg-2, identifying distinct virus lineages within each virus-type and helping to identify strain movements/origins. The RT-PCR methods described here provide a robust and versatile tool for rapid and specific detection

  14. Magnetic and electrical properties of M-type nano-strontium hexaferrite prepared by sol-gel combustion method

    Science.gov (United States)

    Naeem Ashiq, Muhammad; Sami Asi, Abdul; Farooq, Saima; Najam-ul-Haq, Muhammad; Rehman, Sidra

    2017-12-01

    Herein, we report the synthesis of M-type nano-strontium hexaferrites co-doped with hetrovalent cations (Dy-Ni) having composition Sr(1-x)DyxFe12-yNiyO19 (x = 0.00-0.20, y = 0.00-0.80). The synthesized compounds were analyzed by XRD, FE-SEM, VSM, along with electrical resistivity and dielectric property analyses. XRD peak patterns revealed the magnetoplumbite-type hexagonal crystal structure of the synthesized materials. The SEM micrographs reflected the spherical and hexagonal shaped particles with an average size 40-50 nm. The magnetic squareness ratio (Mr/Ms) of the synthesized nano-ferrites particles lies in the range of 0.60-0.68 assuring their single magnetic domain nature. The rise in the values of saturation magnetization, remanence and coercivity reflect that the fabricated compounds can be beneficial for the perpendicular magnetic recording media. Both the electrical resistivity increment and decrease in dielectric energy loss with increasing Dy-Ni substitution level authenticates that such materials can find applications in magnetic recording media and microwave device fabrication.

  15. Preparation and characterization of hybrid materials of epoxy resin type bisphenol a with silicon and titanium oxides by sol-gel process

    International Nuclear Information System (INIS)

    Carrillo C, A.; Osuna A, J. G.

    2011-01-01

    Hybrid materials were synthesized from epoxy resins as a result bisphenol type A-silicon oxide and epoxy resin bisphenol type A-titanium oxide were obtained. The synthesis was done by sol-gel process using tetraethyl orthosilicate (Teos) and titanium isopropoxide (I Ti) as inorganic precursors. The molar ratio of bisphenol A to the inorganic precursors was the studied variable. The materials were characterized by thermal analysis, infrared spectroscopy, scanning electron microscopy and energy dispersive X-ray spectroscopy. The hybrid nature of the materials was demonstrated through thermal analysis and infrared spectroscopy. In both systems, as the amount of alkoxide increased, the bands described above were more defined. This behavior indicates the interactions between the resin and the alkoxides. Hybrids with Teos showed a smoother and homogeneous surface in its entirety, without irregularities. Hybrids with titanium isopropoxide had low roughness. Both Teos and I Ti hybrids showed a decrease on the atomic weight percentage of carbon due to a slight reduction of the organic part on the surface. (Author)

  16. Preparation and characterization of hybrid materials of epoxy resin type bisphenol a with silicon and titanium oxides by sol-gel process

    Energy Technology Data Exchange (ETDEWEB)

    Carrillo C, A.; Osuna A, J. G., E-mail: acc.carrillo@gmail.com [Universidad Autonoma de Coahuila, Facultad de Ciencias Quimicas, Blvd. Venustiano Carranza y Jose Cardenas Valdes, 25000 Saltillo, Coahuila (Mexico)

    2011-07-01

    Hybrid materials were synthesized from epoxy resins as a result bisphenol type A-silicon oxide and epoxy resin bisphenol type A-titanium oxide were obtained. The synthesis was done by sol-gel process using tetraethyl orthosilicate (Teos) and titanium isopropoxide (I Ti) as inorganic precursors. The molar ratio of bisphenol A to the inorganic precursors was the studied variable. The materials were characterized by thermal analysis, infrared spectroscopy, scanning electron microscopy and energy dispersive X-ray spectroscopy. The hybrid nature of the materials was demonstrated through thermal analysis and infrared spectroscopy. In both systems, as the amount of alkoxide increased, the bands described above were more defined. This behavior indicates the interactions between the resin and the alkoxides. Hybrids with Teos showed a smoother and homogeneous surface in its entirety, without irregularities. Hybrids with titanium isopropoxide had low roughness. Both Teos and I Ti hybrids showed a decrease on the atomic weight percentage of carbon due to a slight reduction of the organic part on the surface. (Author)

  17. Population Genetic Structure of Listeria monocytogenes Strains as Determined by Pulsed-Field Gel Electrophoresis and Multilocus Sequence Typing

    DEFF Research Database (Denmark)

    Henri, Clémentine; Félix, Benjamin; Guillier, Laurent

    2016-01-01

    Listeria monocytogenes is a ubiquitous bacterium that may cause the foodborne illness listeriosis. Only a small amount of data about the population genetic structure of strains isolated from food is available. This study aimed to provide an accurate view of the L. monocytogenes food strain....... The distribution of sequence types (STs) was compared between food and clinical strains on a panel of 675 strains. High congruence between PFGE and MLST was found. Out of 73 PFGE clusters, the two most prevalent corresponded to ST9 and ST121. Using original statistical analysis, we demonstrated that (i....... This observation may be directly relevant for refining risk analysis models for the better management of food safety. This study showed a very useful backward compatibility between PFGE and MLST for surveillance. The results enabled better understanding of the population structure of L. monocytogenes strains...

  18. Destruction of gel sulfonated cation-exchangers of the KU-2 type under the influence of hydrogen peroxide

    Energy Technology Data Exchange (ETDEWEB)

    Roginskaya, B.S.; Zavadovskaya, A.S.; Znamenskii, Yu.P.; Paskhina, N.A.; Dobrova, E.I.

    1988-10-20

    The purpose of this work was to study the mechanism of interaction of Soviet sulfonated cation-exchangers of the KU-2 type with hydrogen peroxide. It is shown that under the influence of hydrogen peroxide sulfonated cation-exchangers begin, after a certain induction period, to lose capacity and to release destruction products into water; the length of the induction period increases with the degree of cross-linking. In a given time of contact between the resin and the solution the degree of destruction falls with increase of cross-linking. The principal product of destruction of sulfonated cation-exchangers is an aromatic sulfonic acid containing oxidized groups in the side chains.

  19. Pulsed-field gel electrophoresis and multi locus sequence typing for characterizing genotype variability of Yersinia ruckeri isolated from farmed fish in France.

    Science.gov (United States)

    Calvez, Ségolène; Fournel, Catherine; Douet, Diane-Gaëlle; Daniel, Patrick

    2015-06-23

    Yersinia ruckeri is a pathogen that has an impact on aquaculture worldwide. The disease caused by this bacterial species, yersiniosis or redmouth disease, generates substantial economic losses due to the associated mortality and veterinary costs. For predicting outbreaks and improving control strategies, it is important to characterize the population structure of the bacteria. The phenotypic and genetic homogeneities described previously indicate a clonal population structure as observed in other fish bacteria. In this study, the pulsed-field gel electrophoresis (PFGE) and multi locus sequence typing (MLST) methods were used to describe a population of isolates from outbreaks on French fish farms. For the PFGE analysis, two enzymes (NotI and AscI) were used separately and together. Results from combining the enzymes showed the great homogeneity of the outbreak population with a similarity > 80.0% but a high variability within the cluster (cut-off value = 80.0%) with a total of 43 pulsotypes described and an index of diversity = 0.93. The dominant pulsotypes described with NotI (PtN4 and PtN7) have already been described in other European countries (Finland, Germany, Denmark, Spain and Italy). The MLST approach showed two dominant sequence types (ST31 and ST36), an epidemic structure of the French Y. ruckeri population and a preferentially clonal evolution for rainbow trout isolates. Our results point to multiple types of selection pressure on the Y. ruckeri population attributable to geographical origin, ecological niche specialization and movements of farmed fish.

  20. Comparison of PCR binary typing (P-BIT), a new approach to epidemiological subtyping of Campylobacter jejuni, with serotyping, pulsed-field gel electrophoresis, and multilocus sequence typing methods.

    Science.gov (United States)

    Cornelius, Angela J; Gilpin, Brent; Carter, Philip; Nicol, Carolyn; On, Stephen L W

    2010-03-01

    To overcome some of the deficiencies with current molecular typing schema for Campylobacter spp., we developed a prototype PCR binary typing (P-BIT) approach. We investigated the distribution of 68 gene targets in 58 Campylobacter jejuni strains, one Campylobacter lari strain, and two Campylobacter coli strains for this purpose. Gene targets were selected on the basis of distribution in multiple genomes or plasmids, and known or putative status as an epidemicity factor. Strains were examined with Penner serotyping, pulsed-field gel electrophoresis (PFGE; using SmaI and KpnI enzymes), and multilocus sequence typing (MLST) approaches for comparison. P-BIT provided 100% typeability for strains and gave a diversity index of 98.5%, compared with 97.0% for SmaI PFGE, 99.4% for KpnI PFGE, 96.1% for MLST, and 92.8% for serotyping. Numerical analysis of the P-BIT data clearly distinguished strains of the three Campylobacter species examined and correlated somewhat with MLST clonal complex assignations and with previous classifications of "high" and "low" risk. We identified 18 gene targets that conferred the same level of discrimination as the 68 initially examined. We conclude that P-BIT is a useful approach for subtyping, offering advantages of speed, cost, and potential for strain risk ranking unavailable from current molecular typing schema for Campylobacter spp.

  1. Water equivalence of polymer gel dosimeters

    International Nuclear Information System (INIS)

    Sellakumar, P.; James Jebaseelan Samuel, E.; Supe, Sanjay S.

    2007-01-01

    To evaluate the water equivalence and radiation transport properties of polymer gel dosimeters over the wide range of photon and electron energies 14 different types of polymer gels were considered. Their water equivalence was evaluated in terms of effective atomic number (Z eff ), electron density (ρ e ), photon mass attenuation coefficient (μ/ρ), photon mass energy absorption coefficient (μ en /ρ) and total stopping power (S/ρ) tot of electrons using the XCOM and the ESTAR database. The study showed that the effective atomic number of polymer gels were very close ( en /ρ for all polymer gels were in close agreement ( tot of electrons in polymer gel dosimeters were within 1% agreement with that of water. From the study we conclude that at lower energy (<80keV) the polymer gel dosimeters cannot be considered water equivalent and study has to be carried out before using the polymer gel for clinical application

  2. Influence of carboxylic acid type on microstructure and magnetic properties of polymeric complex sol–gel driven NiFe{sub 2}O{sub 4}

    Energy Technology Data Exchange (ETDEWEB)

    Hessien, M.M. [Materials Science & Engineering Group, Department of Chemistry, Faculty of Science, Taif University (Saudi Arabia); Advanced Materials Dept, Central Metallurgical Research and Development Institute (CMRDI), P.O. Box: 87, Helwan, Cairo (Egypt); Mostafa, Nasser Y., E-mail: nmost69@yahoo.com [Materials Science & Engineering Group, Department of Chemistry, Faculty of Science, Taif University (Saudi Arabia); Department of Chemistry, Faculty of Science, Suez Canal University, Ismailia (Egypt); Abd-Elkader, Omar H. [Department of Zoology, Science College, King Saud University, P.O. Box 2455, Riyadh 11451 (Saudi Arabia); Electron Microscope and Thin Films Department, National Research Center (NRC), El-Behooth Street, Dokki, Cairo 12622 (Egypt)

    2016-01-15

    Citric, oxalic and tartaric acids were used for synthesis of NiFe{sub 2}O{sub 4} using polymeric complex precursor route. The dry precursor gels were calcined at various temperatures (400–1100 °C) for 2 h. All carboxylic acids produce iron-deficient NiFe{sub 2}O{sub 4} with considerable amount of α-Fe{sub 2}O{sub 3} at 400 °C. Increase in the annealing temperature caused reaction of α-Fe{sub 2}O{sub 3} with iron-deficient ferrite phase. The amount of initially formed α-Fe{sub 2}O{sub 3} is directly correlated with stability constant and inversely correlated with the decomposition temperature of Fe(III) carboxylate precursors. In case of tartaric acid precursor, single phase of the ferrite was obtained at 450 °C. However, in case of oxalic acid and citric acid precursors, single phase ferrite was obtained at 550 °C and 700 °C, respectively. The lattice parameters were increased with increasing annealing temperature and with decreasing the amount of α-Fe{sub 2}O{sub 3}. Maximum saturation magnetization (55 emu/g) was achieved using tartaric acid precursor annealed at 1100 °C. - Highlights: • Citric, oxalic and tartaric acids were used for synthesis of NiFe{sub 2}O{sub 4}. • Carboxylic acid type affects the produced powders. • At low temperatures all carboxylic acids produce iron-deficient NiFe{sub 2}O{sub 4} and α-Fe{sub 2}O{sub 3}. • α-Fe{sub 2}O{sub 3} is correlated with the decomposition of Fe(III) carboxylate precursors.

  3. Effect of Tb{sup 3+} substitution on the structural and magnetic properties of M-type hexaferrites synthesized by sol-gel auto-combustion technique

    Energy Technology Data Exchange (ETDEWEB)

    Ali, Ihsan, E-mail: muislampk@yahoo.com [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Islam, M.U. [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Awan, M.S. [Center for Micro and Nano Devices, Department of Physics, COMSATS Institute of Information Technology, Islamabad (Pakistan); Ahmad, Mukhtar [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Ashiq, Muhammad Naeem [Institute of Chemical Sciences, Bahauddin Zakariya University, Multan 60800 (Pakistan); Naseem, Shahzad [Centre for Solid State Physics, University of the Punjab, Lahore 54560 (Pakistan)

    2013-02-15

    M-type hexaferrites with new substitution of rare-earth element Tb{sup 3+} having nominal composition Ba{sub 0.5}Sr{sub 0.5-x}Tb{sub x}AlFe{sub 11}O{sub 19} (x = 0.0, 0.05, 0.1, 0.15, 0.2, and 0.25) were synthesized by the sol-gel auto-combustion technique. The main aim of study is to investigate the effect of terbium (Tb{sup 3+}) ions substitution at Sr{sup 2+} site on the structural and magnetic properties. The materials were characterized by Differential Scanning Calorimetry, Thermogravimetry, Fourier Transform Infra-Red spectroscopy, X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy and vibrating sample magnetometery analyses. The XRD patterns confirm the formation of M-type hexaferrite phase. The crystallite size was found to be in the range of 17-45 nm which is good enough to obtain the suitable signal-to-noise ratio in the high density recording media. The magnetic properties such as saturation magnetization (M{sub s}), retentivity (M{sub r}), squareness ratio (M{sub r}/M{sub s}) and coercivity (H{sub c}) were calculated from the MH-loops. The saturation magnetization (M{sub s}) and retentivity (M{sub r}) decreased from 48.9-26.9 and 36.8-18.1 emu/g, respectively which may be due to spin canting and hence reduction in the super-exchange interactions. The enhancement of coercivity (H{sub c}) from 1825 to 4440 G may be due to higher magnetocrystalline anisotropy, which is due to the Fe{sup 2+} ions located on a 2a site. The magnetic properties such as retentivity (M{sub r}) and coercivity (H{sub c}) make the synthesized materials useful for high density recording media and permanent magnets.

  4. Combination of multilocus sequence typing and pulsed-field gel electrophoresis reveals an association of molecular clonality with the emergence of extensive-drug resistance (XDR) in Salmonella.

    Science.gov (United States)

    Cao, Yongzhong; Shen, Yongxiu; Cheng, Lingling; Zhang, Xiaorong; Wang, Chao; Wang, Yan; Zhou, Xiaohui; Chao, Guoxiang; Wu, Yantao

    2018-03-01

    Salmonellae is one of the most important foodborne pathogens and becomes resistant to multiple antibiotics, which represents a significant challenge to food industry and public health. However, a molecular signature that can be used to distinguish antimicrobial resistance profile, particularly multi-drug resistance or extensive-drug resistance (XDR). In the current study, 168 isolates from the chicken and pork production chains and ill chickens were characterized by serotyping, antimicrobial susceptibility test, multilocus sequence typing (MLST) and pulsed-field gel electrophoresis (PFGE). The results showed that these isolates belonged to 13 serotypes, 14 multilocus sequence types (STs), 94 PFGE genotypes, and 70 antimicrobial resistant profiles. S. Enteritidis, S. Indiana, and S. Derby were the predominant serotypes, corresponding to the ST11, ST17, and ST40 clones, respectively and the PFGE Cluster A, Cluster E, and Cluster D, respectively. Among the ST11-S. Enteritidis (Cluster A) and the ST40-S. Derby (Cluster D) clones, the majority of isolates were resistant to 4-8 antimicrobial agents, whereas in the ST17S. Indiana (Cluster E) clone, isolates showed extensive-drug resistance (XDR) to 9-16 antimicrobial agents. The bla TEM-1-like gene was prevalent in the ST11 and ST17 clones corresponding to high ampicillin resistance. The bla TEM-1-like , bla CTX-M , bla OXA-1-like , sul1, aaC4, aac(6')-1b, dfrA17, and floR gene complex was highly prevalent among isolates of ST17, corresponding to an XDR phenotype. These results demonstrated the association of the resistant phenotypes and genotypes with ST clone and PFGE cluster. Our results also indicated that the newly identified gene complex comprising bla TEM-1-like , bla CTX-M , bla OXA-1-like , sul1, aaC4, aac(6')-1b, dfrA17, and floR, was responsible for the emergence of the ST17S. Indiana XDR clone. ST17 could be potentially used as a molecular signature to distinguish S. Indiana XDR clone. Copyright © 2017

  5. Clinical potential of mechlorethamine gel for the topical treatment of mycosis fungoides-type cutaneous T-cell lymphoma: a review on current efficacy and safety data

    Directory of Open Access Journals (Sweden)

    Liner K

    2018-01-01

    Full Text Available Kendall Liner,1 Celeste Brown,2 Laura Y McGirt3 1Division of Dermatology, Medical College of Georgia at Augusta Health, Augusta, GA, USA; 2School of Medicine, University of North Carolina at Chapel Hill, Carolinas Medical Center, Charlotte, NC, USA; 3Department of Hematology/Oncology, Levine Cancer Institute, Carolinas Medical Center, Charlotte, NC, USA Abstract: Nitrogen mustard is a chemotherapeutic agent that has a well-documented safety and efficacy profile in the treatment of cutaneous T-cell lymphoma. Development of nitrogen mustard formulations and treatment regimens has been studied extensively over the last 40 years. In the last 5 years, a new gel formulation has been developed that is associated with a decrease in delayed hypersensitivity reactions. The authors in this review found that while the gel formulation may result in a decrease of allergic contact dermatitis, this advantage has been replaced by a higher number of irritant contact reactions and a decrease in complete response rate. The gel formulation has a complete response rate of 13.8%, which is a decrease in efficacy when compared to aqueous-based preparations of similar concentrations. Keywords: mycosis fungoides, nitrogen mustard, mechlorethamine gel, cutaneous T-cell lymphoma, CTCL, Valchlor®

  6. New type of gel polyelectrolytes based on selected methacrylates and their characteristics. Part I. Copolymers with (3-(trimethoxysilyl)propyl methacrylate)

    Czech Academy of Sciences Publication Activity Database

    Musil, M.; Michálek, Jiří; Abbrent, Sabina; Kovářová, Jana; Přádný, Martin; Doubková, L.; Vondrák, J.; Sedlaříková, M.

    2015-01-01

    Roč. 155, 10 February (2015), s. 183-195 ISSN 0013-4686 R&D Projects: GA ČR(CZ) GAP102/10/2091 Institutional support: RVO:61389013 Keywords : gel polymer electrolytes * thermal analysis * ionic conductivity Subject RIV: CG - Electrochemistry Impact factor: 4.803, year: 2015

  7. Layered Lepidocrocite Type Structure Isolated by Revisiting the Sol–Gel Chemistry of Anatase TiO 2 : A New Anode Material for Batteries

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Jiwei [Sorbonne Universités,; Reeves, Kyle G. [Sorbonne Universités,; Porras Gutierrez, Ana-Gabriela [Sorbonne Universités,; Body, Monique [Université; Legein, Christophe [Université; Kakinuma, Katsuyoshi [Fuel; Borkiewicz, Olaf J. [X-ray; Chapman, Karena W. [X-ray; Groult, Henri [Sorbonne Universités,; Salanne, Mathieu [Sorbonne Universités,; Réseau; Dambournet, Damien [Sorbonne Universités,; Réseau

    2017-09-19

    Searches for new electrode materials for batteries must comply on financial and environmental costs to be useful in practical devices. The sol-gel chemistry has been widely used to design and implemented new concepts for the emergence of advanced materials such as hydride organic-inorganic composites. Here, we show that the simple reaction system including titanium alkoxide and water can be used to stabilize a new class of electrode materials. By investigating the crystallization path of anatase TiO2, an X-ray amorphous intermediate phase has been identified whose local structure probed by the pair distribution function, 1H solid-state NMR and DFT calculations, consists of a layered-type structure as found in the lepido-crocite. This phase presents the following general formula Ti2-xxO4-4x(OH)4x.nH2O (x ~ 0.5) where the substitution of oxide by hydroxide anions leads to the formation of titanium vacancies (•) and H2O molecules are located in interlayers. Solid-state 1H NMR has enabled to characterize three main hydroxide environments that are Ti⟂-OH, Ti22-OH and Ti3⟂-OH and layered H2O molecules. The electrochemical properties of this phase were further investigated versus lithium and is shown to be very promising with reversible capacities of around 200 mAh.g-1 and an operating voltage of 1.55 V. We further showed that the lithium intercalation proceeds via a solid-solution mechanism. 7Li solid-state NMR and DFT calculations allowed to identify lithium host sites that are located at the titanium vacancies and interlayer space with lithium being solvated by structural water molecules. The easy fabrication, the absence of lithium and easier recycling and the encouraging properties makes this class of materials very attractive for competitive electrodes for batteries. We thus demonstrate that the revisit of an “old” chemistry with

  8. Silica reinforced triblock copolymer gels

    DEFF Research Database (Denmark)

    Theunissen, E.; Overbergh, N.; Reynaers, H.

    2004-01-01

    The effect of silica and polymer coated silica particles as reinforcing agents on the structural and mechanical properties of polystyrene-poly(ethylene/butylene)-polystyrene (PS-PEB-PS) triblock gel has been investigated. Different types of chemically modified silica have been compared in order...

  9. Identification of the EcoKI and EcoR124I Type I restriction--modification enzyme subunits by non-equilibrium pH gradient two-dimensional gel electrophoresis.

    Science.gov (United States)

    Nguyen, L D; Cajthamlová, K; Nguyen, H T; Weiser, J; Holubová, I; Weiserová, M

    2002-01-01

    Effectively optimized and reproducible procedure for monitoring the composition of type I restriction-modification endonucleases EcoKI and EcoR124I by non-equilibrium pH gradient two-dimensional (2-D) gel electrophoresis is described. Three subunits of the enzyme complex, which widely differ from one another in their isoelectric points and molar mass, were identified in crude cell extracts of E. coli. For the first time all three subunits of both EcoKI and EcoR124I were detected as distinct spots on a single 2-D gel. A sensitive immunoblotting procedure was suggested suitable for routine use in determining the identity of individual subunits. Potential application of this method for detailed studies of regulation of the function and stoichiometry of the enzyme complexes is discussed.

  10. The influence of charge transfers effects in monazite-type LaVO{sub 4} and perovskite-type LaVO{sub 3} prepared by sol-gel acrylamide polymerization

    Energy Technology Data Exchange (ETDEWEB)

    Herrera-Pérez, G., E-mail: guillermo.herrera@cimav.edu.mx [CONACYT Research Fellow. Centro de Investigación en Materiales Avanzados (CIMAV), Miguel de Cervantes 120, Chihuahua 31136, Chihuahua (Mexico); Jiménez-Mier, J. [Instituto de Ciencias Nucleares, Universidad Nacional Autónoma de México, 04510 Mexico D. F (Mexico); Yang, W.-L. [The Advanced Light Source, Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Reyes-Rojas, A.; Fuentes-Cobas, L.E. [Department of Physics of Materials Department. Centro de Investigación en Materiales Avanzados (CIMAV), Miguel de Cervantes 120, Chihuahua 31136, Chihuahua (Mexico)

    2016-08-15

    Highlights: • We elucidate the electronic structure through the vanadium L{sub 2,3} edge in LaVO{sub 4} by XAS. • The interpretation of XAS spectrum was performed by the multiplet calculation. • Our results suggest that LaVO{sub 4} can be considered in the charge transfer regime. - Abstract: Core-hole spectroscopy such as X-ray absorption spectroscopy (XAS) is useful to determine the electronic structure of strongly correlated and strongly hybridized compounds such as vanadates. Monazite-type LaVO{sub 4} and perovskite-type LaVO{sub 3} are good candidates to elucidate the electronic structure through the vanadium L{sub 2,3} edge. LaVO{sub 4} was prepared by sol-gel acrylamide polymerization and solid-state reaction. LaVO{sub 3} was obtained by reduction of LaVO{sub 4} using Zr as gatherer. Monoclinic crystal phase for LaVO{sub 4} and orthorhombic crystal phase for LaVO{sub 3} were confirmed by the Rietveld refinement of X-ray diffraction patterns. XAS comparison between Vanadium L{sub 2,3} edge confirms the presence of V{sup 5+} for the monazite and V{sup 3+} for the orthorhombic perovskite. Multiplet calculations including crystal field and charge transfer effects (CTM) were performed in order to elucidate the tetragonal (D{sub 4h} symmetry) parameters Dq, Ds and Dt, the charge transfer energy Δ, and d-d Coulomb repulsion energy U parameters. CTM confirms for LaVO{sub 3} the strong V 3d–O 2p hybridization with a significant contribution of covalent character due to the delocalization of 3d electrons. For LaVO{sub 4} this work suggest the reclassification of this band insulator as charge transfer insulator that shows a significant contribution of ionic character.

  11. Removing water from gels

    International Nuclear Information System (INIS)

    Lane, E.S.; Winter, J.A.

    1982-01-01

    Water is removed from a gel material by contacting the gel material with an organic liquid and contacting the organic liquid with a gas such that water is taken up by the gas. The invention, in one embodiment, may be used to dry gel materials whilst maintaining an open porous network therein. In one example, the invention is applied to gel precipitated spheres containing uranium and plutonium. (author)

  12. Polymer gels and networks

    National Research Council Canada - National Science Library

    Osada, Yoshihito; Khokhlov, A. R

    2002-01-01

    ... or magnetic field, etc.). It was realized that not only can polymer gels absorb and hold a considerable volume of liquids, but they can also be forced to expel the absorbed liquid in a controlled manner. Of particular interest are hydrogels, i.e., polymer gels, which swell extensively in water. The most common hydrogels are polyelectrolyte gels: ...

  13. Internal structure analysis of particle-double network gels used in a gel organ replica

    Science.gov (United States)

    Abe, Mei; Arai, Masanori; Saito, Azusa; Sakai, Kazuyuki; Kawakami, Masaru; Furukawa, Hidemitsu

    2016-04-01

    In recent years, the fabrication of patient organ replicas using 3D printers has been attracting a great deal of attention in medical fields. However, the cost of these organ replicas is very high as it is necessary to employ very expensive 3D printers and printing materials. Here we present a new gel organ replica, of human kidney, fabricated with a conventional molding technique, using a particle-double network hydrogel (P-DN gel). The replica is transparent and has the feel of a real kidney. It is expected that gel organ replicas produced this way will be a useful tool for the education of trainee surgeons and clinical ultrasonography technologists. In addition to developing a gel organ replica, the internal structure of the P-DN gel used is also discussed. Because the P-DN gel has a complex structure comprised of two different types of network, it has not been possible to investigate them internally in detail. Gels have an inhomogeneous network structure. If it is able to get a more uniform structure, it is considered that this would lead to higher strength in the gel. In the present study we investigate the structure of P-DN gel, using the gel organ replica. We investigated the internal structure of P-DN gel using Scanning Microscopic Light Scattering (SMILS), a non-contacting and non-destructive.

  14. Ionic liquid based multifunctional double network gel

    Science.gov (United States)

    Ahmed, Kumkum; Higashihara, Tomoya; Arafune, Hiroyuki; Kamijo, Toshio; Morinaga, Takashi; Sato, Takaya; Furukawa, Hidemitsu

    2015-04-01

    Gels are a promising class of soft and wet materials with diverse application in tissue engineering and bio-medical purpose. In order to accelerate the development of gels, it is required to synthesize multi-functional gels of high mechanical strength, ultra low surface friction and suitable elastic modulus with a variety of methods and new materials. Among many types of gel ionic gel made from ionic liquids (ILs) could be used for diverse applications in electrochemical devices and in the field of tribology. IL, a promising materials for lubrication, is a salt with a melting point lower than 100 °C. As a lubricant, ILs are characterized by an extremely low vapor pressure, high thermal stability and high ion conductivity. In this work a novel approach of making double network DN ionic gel using IL has been made utilizing photo polymerization process. A hydrophobic monomer Methyl methacrylate (MMA) has been used as a first network and a hydrophobic IL monomer, N,N-diethyl-N-(2-mthacryloylethyl)-N-methylammonium bistrifluoromethylsulfonyl)imide (DEMM-TFSI) has been used as a second network using photo initiator benzophenon and crosslinker triethylene glycol dimethacrylate (TEGDMA). The resulting DN ionic gel shows transparency, flexibility, high thermal stability, good mechanical toughness and low friction coefficient value which can be a potential candidate as a gel slider in different mechanical devices and can open a new area in the field of gel tribology.

  15. Transport Phenomena in Gel

    Directory of Open Access Journals (Sweden)

    Masayuki Tokita

    2016-05-01

    Full Text Available Gel becomes an important class of soft materials since it can be seen in a wide variety of the chemical and the biological systems. The unique properties of gel arise from the structure, namely, the three-dimensional polymer network that is swollen by a huge amount of solvent. Despite the small volume fraction of the polymer network, which is usually only a few percent or less, gel shows the typical properties that belong to solids such as the elasticity. Gel is, therefore, regarded as a dilute solid because its elasticity is much smaller than that of typical solids. Because of the diluted structure, small molecules can pass along the open space of the polymer network. In addition to the viscous resistance of gel fluid, however, the substance experiences resistance due to the polymer network of gel during the transport process. It is, therefore, of importance to study the diffusion of the small molecules in gel as well as the flow of gel fluid itself through the polymer network of gel. It may be natural to assume that the effects of the resistance due to the polymer network of gel depends strongly on the network structure. Therefore, detailed study on the transport processes in and through gel may open a new insight into the relationship between the structure and the transport properties of gel. The two typical transport processes in and through gel, that is, the diffusion of small molecules due to the thermal fluctuations and the flow of gel fluid that is caused by the mechanical pressure gradient will be reviewed.

  16. Pulsed-field gel electrophoresis typing of Escherichia coli strains from samples collected before and after pivmecillinam or placebo treatment of uncomplicated community-acquired urinary tract infection in women

    DEFF Research Database (Denmark)

    Ejrnaes, Karen; Sandvang, Dorthe; Lundgren, Bettina

    2006-01-01

    The primary infecting Escherichia coli strains from 156 women with community-acquired uncomplicated urinary tract infection (UTI) randomized to pivmecillinam or placebo and the E. coli strains causing UTI at two follow-up visits were typed using pulsed-field gel electrophoresis (PFGE......). The finding that the majority of UTIs at follow-up are caused by the primary infecting E. coli strain supports the theory of a vaginal and rectal reservoir but could also support the recent discovery that E. coli strains are able to persist in the bladder epithelium despite appropriate antibiotic treatment......, constituting a reservoir for recurrent UTI....

  17. Pulsed-field gel electrophoresis typing of Eschericia coli strains from samples collected before and after pivmecillinam or placebo treatment of uncomplicated community-acquired urinary tract infection in women

    DEFF Research Database (Denmark)

    Ejrnæs, K; Sandvang, D; Lundgren, Bettina

    2006-01-01

    The primary infecting Escherichia coli strains from 156 women with community-acquired uncomplicated urinary tract infection (UTI) randomized to pivmecillinam or placebo and the E. coli strains causing UTI at two follow-up visits were typed using pulsed-field gel electrophoresis (PFGE......). The finding that the majority of UTIs at follow-up are caused by the primary infecting E. coli strain supports the theory of a vaginal and rectal reservoir but could also support the recent discovery that E. coli strains are able to persist in the bladder epithelium despite appropriate antibiotic treatment......, constituting a reservoir for recurrent UTI....

  18. Sol-Gel Glasses

    Science.gov (United States)

    Mukherjee, S. P.

    1985-01-01

    Multicomponent homogeneous, ultrapure noncrystalline gels/gel derived glasses are promising batch materials for the containerless glass melting experiments in microgravity. Hence, ultrapure, homogeneous gel precursors could be used to: (1) investigate the effect of the container induced nucleation on the glass forming ability of marginally glass forming compositions; and (2) investigate the influence of gravity on the phase separation and coarsening behavior of gel derived glasses in the liquid-liquid immiscibility zone of the nonsilicate systems having a high density phase. The structure and crystallization behavior of gels in the SiO2-GeO2 as a function of gel chemistry and thermal treatment were investigated. As are the chemical principles involved in the distribution of a second network former in silica gel matrix being investigated. The procedures for synthesizing noncrystalline gels/gel-monoliths in the SiO2-GeO2, GeO2-PbO systems were developed. Preliminary investigations on the levitation and thermal treatment of germania silicate gel-monoliths in the Pressure Facility Acoustic Levitator were done.

  19. Structural and thermoelectric characterization of Ba substituted LaCoO3 perovskite-type materials obtained by polymerized gel combustion method

    International Nuclear Information System (INIS)

    Kun, Robert; Populoh, Sascha; Karvonen, Lassi; Gumbert, Julia; Weidenkaff, Anke; Busse, Matthias

    2013-01-01

    Highlights: •Ba-substituted LaCoO 3 perovskites prepared by polymerized gel combustion method. •Φ affects the agglomeration grade, compacting, sintering behavior of the perovskites. •ZT-values reach maximum at 400–500 K temperature range. -- Abstract: Structural and thermoelectric transport properties of Ba 2+ containing lanthanum cobaltate (La 1−x Ba x CoO 3 ; x = 0.01, 0.03, 0.05) prepared by soft chemistry method were investigated and discussed. The influence of the fuel-to-oxidizer ratio (Φ) of the redox mixture on the powder microstructure was studied. The agglomeration grade of the nanocrystalline perovskite phases can be influenced due to initial composition of the redox mixture. Since the different burning characteristic of the polymerized gels results in different xerogel structures, the as-calcined single phase perovskite samples show different compacting and sintering behavior. The thermoelectric transport properties were measured in the 300–1300 K temperature range. It was found that the electrical and thermal conductivity of the sintered pellets show strong dependence on microstructure. In addition increasing Ba 2+ content in the samples results in lower thermal conductivity values (κ < 1.5 W/K m). The calculated dimensionless figure of merit (ZT) showed maximum value in the 400–500 K range

  20. Structural and thermoelectric characterization of Ba substituted LaCoO{sub 3} perovskite-type materials obtained by polymerized gel combustion method

    Energy Technology Data Exchange (ETDEWEB)

    Kun, Robert, E-mail: robert.kun@uni-bremen.de [University of Bremen, FB 4, Near Net Shape Technologies, Wiener Str. 12, 28359 Bremen (Germany); Populoh, Sascha; Karvonen, Lassi [Solid State Chemistry and Catalysis, EMPA, Swiss Federal Laboratories for Materials Science and Technology, Ueberlandstrasse 129, CH-8600 Duebendorf (Switzerland); Gumbert, Julia [University of Bremen, FB 4, Near Net Shape Technologies, Wiener Str. 12, 28359 Bremen (Germany); Weidenkaff, Anke [Solid State Chemistry and Catalysis, EMPA, Swiss Federal Laboratories for Materials Science and Technology, Ueberlandstrasse 129, CH-8600 Duebendorf (Switzerland); Busse, Matthias [University of Bremen, FB 4, Near Net Shape Technologies, Wiener Str. 12, 28359 Bremen (Germany); Fraunhofer Institute for Manufacturing Technology and Applied Materials Research, IFAM, Wiener Str. 12, 28359 Bremen (Germany)

    2013-12-05

    Highlights: •Ba-substituted LaCoO{sub 3} perovskites prepared by polymerized gel combustion method. •Φ affects the agglomeration grade, compacting, sintering behavior of the perovskites. •ZT-values reach maximum at 400–500 K temperature range. -- Abstract: Structural and thermoelectric transport properties of Ba{sup 2+} containing lanthanum cobaltate (La{sub 1−x}Ba{sub x}CoO{sub 3}; x = 0.01, 0.03, 0.05) prepared by soft chemistry method were investigated and discussed. The influence of the fuel-to-oxidizer ratio (Φ) of the redox mixture on the powder microstructure was studied. The agglomeration grade of the nanocrystalline perovskite phases can be influenced due to initial composition of the redox mixture. Since the different burning characteristic of the polymerized gels results in different xerogel structures, the as-calcined single phase perovskite samples show different compacting and sintering behavior. The thermoelectric transport properties were measured in the 300–1300 K temperature range. It was found that the electrical and thermal conductivity of the sintered pellets show strong dependence on microstructure. In addition increasing Ba{sup 2+} content in the samples results in lower thermal conductivity values (κ < 1.5 W/K m). The calculated dimensionless figure of merit (ZT) showed maximum value in the 400–500 K range.

  1. Evaluation of a capillary zone electrophoresis system versus a conventional agarose gel system for routine serum protein separation and monoclonal component typing.

    Science.gov (United States)

    Roudiere, L; Boularan, A M; Bonardet, A; Vallat, C; Cristol, J P; Dupuy, A M

    2006-01-01

    Capillary zone electrophoresis of serum proteins is increasingly gaining impact in clinical laboratories. During 2003, we compared the fully automated capillary electrophoresis (CE) system from Beckman (Paragon CZE 2000) with the method agarose gel electrophoresis Sebia (Hydrasis-Hyris, AGE). This new study focused on the evaluation of analytical performance and a comparison including 115 fresh routine samples (group A) and a series of 97 frozen pathologic sera with suspicion of monoclonal protein (group B). Coefficients of variation (CVs %) for the five classical protein fractions have been reported to be consistenly serum samples (group B), there were 90 in which we detected a monoclonal protein by immunofixation (IF) (immunosubtraction (IS) was not used). AGE and Paragon 2000 failed to detect 7 and 12 monoclonal proteins, respectively, leading to a concordance to 92% for AGE and 87% for Paragon 2000 for identifying electrophoretic abnormalities in this group. Beta-globulin abnormalities and M paraprotein were well detected with Paragon 2000. Only 81% (21 vs 26) of the gammopathies were immunotyped with IS by two readers blinded to the IF immunotype. The Paragon 2000 is a reliable alternative to conventional agarose gel electrophoresis combining the advantages of full automation (rapidity, ease of use and cost) with high analytical performance. Qualified interpretation of results requires an adaptation period which could further improve concordance between the methods. Recently, this CE system has been improved by the manufacturer (Beckman) concerning the migration buffer and detection of beta-globulin abnormalities.

  2. On shear rheology of gel propellants

    Energy Technology Data Exchange (ETDEWEB)

    Rahimi, Shai; Peretz, Arie [RAFAEL, MANOR Propulsion and Explosive Systems Division, Haifa (Israel); Natan, Benveniste [Faculty of Aerospace Engineering, Technion - Israel Institute of Technology, Haifa (Israel)

    2007-04-15

    Selected fuel, oxidizer and simulant gels were prepared and rheologically characterized using a rotational rheometer. For fuel gelation both organic and inorganic gellants were utilized, whereas oxidizers and simulants were gelled with addition of silica and polysaccharides, respectively. The generalized Herschel-Bulkley constitutive model was found to most adequately represent the gels studied. Hydrazine-based fuels, gelled with polysaccharides, were characterized as shear-thinning pseudoplastic fluids with low shear yield stress, whereas inhibited red-fuming nitric acid (IRFNA) and hydrogen peroxide oxidizers, gelled with silica, were characterized as yield thixotropic fluids with significant shear yield stress. Creep tests were conducted on two rheological types of gels with different gellant content and the results were fitted by Burgers-Kelvin viscoelastic constitutive model. The effect of temperature on the rheological properties of gel propellant simulants was also investigated. A general rheological classification of gel propellants and simulants is proposed. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

  3. Nondenaturing agarose gel electrophoresis of RNA.

    Science.gov (United States)

    Rio, Donald C; Ares, Manuel; Hannon, Gregory J; Nilsen, Timothy W

    2010-06-01

    INTRODUCTION Perhaps the most important and certainly the most often used technique in RNA analysis is gel electrophoresis. Because RNAs are negatively charged, they migrate toward the anode in the presence of electric current. The gel acts as a sieve to selectively impede the migration of the RNA in proportion to its mass, given that its mass is generally proportional to its charge. Because mass is approximately related to chain length, the length of an RNA is more generally determined by its migration. In addition, topology (i.e., circularity) can affect migration, making RNAs appear longer on the gel than they actually are. There are two common types of gel: polyacrylamide and agarose. For most applications involving RNAs of or =600 nucleotides, and are especially useful for analysis of mRNAs (e.g., by Northern blotting). RNA analysis on agarose gels is essentially identical to DNA analysis (except that the gel boxes used must be dedicated to RNA work or to other ribonuclease-free work). Here we describe the use of straightforward Tris borate, EDTA (TBE) gels for routine analysis. These gels are appropriate for determining the quantity and integrity of RNA before using it for other applications. This procedure should not be used to determine size with accuracy, because the RNA will not remain in its extended state throughout the run.

  4. GelTouch

    DEFF Research Database (Denmark)

    Miruchna, Viktor; Walter, Robert; Lindlbauer, David

    2015-01-01

    We present GelTouch, a gel-based layer that can selectively transition between soft and stiff to provide tactile multi-touch feedback. It is flexible, transparent when not activated, and contains no mechanical, electromagnetic, or hydraulic components, resulting in a compact form factor (a 2mm thin...... touchscreen layer for our prototype). The activated areas can be morphed freely and continuously, without being limited to fixed, predefined shapes. GelTouch consists of a poly(N-isopropylacrylamide) gel layer which alters its viscoelasticity when activated by applying heat (>32 C). We present three different...

  5. Transport Phenomena in Gel

    OpenAIRE

    Masayuki Tokita

    2016-01-01

    Gel becomes an important class of soft materials since it can be seen in a wide variety of the chemical and the biological systems. The unique properties of gel arise from the structure, namely, the three-dimensional polymer network that is swollen by a huge amount of solvent. Despite the small volume fraction of the polymer network, which is usually only a few percent or less, gel shows the typical properties that belong to solids such as the elasticity. Gel is, therefore, regarded as a dilu...

  6. Improved protocol for isolation of Campylobacter spp. from retail broiler meat and use of pulsed field gel electrophoresis for the typing of isolates.

    Science.gov (United States)

    Oyarzabal, Omar A; Williams, Aretha; Zhou, Ping; Samadpour, Mansour

    2013-10-01

    To improve the detection of Campylobacter spp. in retail broiler meat, a reference method (R subsamples) based on the enrichment of 25 g of meat in Bolton broth at 42°C under microaerobiosis was compared with an alternative method (A subsamples) consisting in the rinsing of meat samples for 30s in buffered peptone water with antimicrobials with incubation at 42°C under aerobiosis. One piece of meat (breasts, tenderloins and thighs) was rinse in experiment 1 (A1) and two pieces in experiment 2 (A2). Campylobacter spp. were isolated on agar plates and identified by PCR. Retail samples in Alabama had less prevalence (P ≤ 0.05) than samples in the state of Washington. The percentage of positive was higher (P ≤ 0.05) in A than in R subsamples and rinsing two pieces of meat yielded the highest percentage of positive subsamples. R subsamples showed variations in the prevalence by product. However, A subsamples had similar prevalence of positives among products compare to the result from reference method. More Campylobacter coli isolates were collected in A2 subsamples. Pulse field gel electrophoresis (PFGE) was used as subtyping method to study the genome similarity among the isolates from all methods. A larger diversity of isolates were detected by PFGE in A2 subsamples. Denaturing gradient gel electrophoresis analysis suggested that the initial bacterial populations of the meat samples impact the final bacterial profile after enrichment. Rinsing broiler meats was less time consuming, required less sample preparation and was more sensitive than the reference method for the isolation of naturally occurring Campylobacter spp. This new method could help with epidemiological and intervention studies to control Campylobacter spp. Copyright © 2013 Elsevier B.V. All rights reserved.

  7. Cyanocobalamin Nasal Gel

    Science.gov (United States)

    ... to supply extra vitamin B12 to people who need unusually large amounts of this vitamin because they are pregnant or have certain diseases. ... Cyanocobalamin nasal gel will supply you with enough vitamin B12 only as ... it regularly. You may need to use cyanocobalamin nasal gel every week for ...

  8. Modeling chemoresponsive polymer gels.

    Science.gov (United States)

    Kuksenok, Olga; Deb, Debabrata; Dayal, Pratyush; Balazs, Anna C

    2014-01-01

    Stimuli-responsive gels are vital components in the next generation of smart devices, which can sense and dynamically respond to changes in the local environment and thereby exhibit more autonomous functionality. We describe recently developed computational methods for simulating the properties of such stimuli-responsive gels in the presence of optical, chemical, and thermal gradients. Using these models, we determine how to harness light to drive shape changes and directed motion in spirobenzopyran-containing gels. Focusing on oscillating gels undergoing the Belousov-Zhabotinksy reaction, we demonstrate that these materials can spontaneously form self-rotating assemblies, or pinwheels. Finally, we model temperature-sensitive gels that encompass chemically reactive filaments to optimize the performance of this system as a homeostatic device for regulating temperature. These studies could facilitate the development of soft robots that autonomously interconvert chemical and mechanical energy and thus perform vital functions without the continuous need of external power sources.

  9. Extended release microparticle-in-gel formulation of octreotide: Effect of polymer type on acylation of peptide during in vitro release.

    Science.gov (United States)

    Vaishya, Ravi D; Mandal, Abhirup; Patel, Sulabh; Mitra, Ashim K

    2015-12-30

    Polymeric microparticles (MPs)-in-gel formulations for extended delivery of octreotide were developed. We investigated influence of polymer composition on acylation of octreotide and kinetics of release during in vitro release from biodegradable polymeric formulations. Polycaprolactone (PCL), polylactic acid (PLA), polyglycolic acid (PGA) and polyethylene glycol (PEG) based triblock (TB≈PCL10k-PEG2k-PCL10k) and pentablock (PBA≈PLA3k-PCL7k-PEG2k-PCL7k-PLA3k and PBB≈PGA3k-PCL7k-PEG2k-PCL7k-PGA3k) polymers were investigated. Octreotide was encapsulated in MPs using methanol-oil/water emulsion solvent evaporation method. The particles were characterized for size, morphology, encapsulation efficiency, drug loading and in vitro release. Release samples were subjected to HPLC analysis for quantitation and HPLC-MS analysis for identification of native and chemically modified octreotide adducts. Entrapment efficiency of methanol-oil/water method with TB, PBA and PBB polymers were 45%, 60%, and 82%, respectively. A significant fraction of released octreotide was acylated from lactide and glycolide based PBA (53%) and PBB (92%) polymers. Substantial amount of peptide was not released from PBB polymers after 330 days of incubation. Complete release of octreotide was achieved from TB polymer over a period of 3 months with minimal acylation of peptide (13%). PCL based polymers resulted in minimal acylation of peptide and hence may be suitable for extended peptide and protein delivery. Conversely, polymers having PLA and PGA blocks may not be appropriate for peptide delivery due to acylation and incomplete release. Copyright © 2015 Elsevier B.V. All rights reserved.

  10. Pulsed-field gel electrophoresis typing of Eschericia coli strains from samples collected before and after pivmecillinam or placebo treatment of uncomplicated community-acquired urinary tract infection in women

    DEFF Research Database (Denmark)

    Ejrnæs, K; Sandvang, D; Lundgren, Bettina

    2006-01-01

    ). The finding that the majority of UTIs at follow-up are caused by the primary infecting E. coli strain supports the theory of a vaginal and rectal reservoir but could also support the recent discovery that E. coli strains are able to persist in the bladder epithelium despite appropriate antibiotic treatment......The primary infecting Escherichia coli strains from 156 women with community-acquired uncomplicated urinary tract infection (UTI) randomized to pivmecillinam or placebo and the E. coli strains causing UTI at two follow-up visits were typed using pulsed-field gel electrophoresis (PFGE......). In the pivmecillinam treatment group PFGE showed that among patients having a negative urine culture at the first follow-up 77% (46/60) had a relapse with the primary infecting E. coli strain and 23% (14/60) had reinfection with a new E. coli strain at the second follow-up. Among patients having E. coli at the first...

  11. Pulsed-field gel electrophoresis typing of Escherichia coli strains from samples collected before and after pivmecillinam or placebo treatment of uncomplicated community-acquired urinary tract infection in women

    DEFF Research Database (Denmark)

    Ejrnaes, Karen; Sandvang, Dorthe; Lundgren, Bettina

    2006-01-01

    ). The finding that the majority of UTIs at follow-up are caused by the primary infecting E. coli strain supports the theory of a vaginal and rectal reservoir but could also support the recent discovery that E. coli strains are able to persist in the bladder epithelium despite appropriate antibiotic treatment......The primary infecting Escherichia coli strains from 156 women with community-acquired uncomplicated urinary tract infection (UTI) randomized to pivmecillinam or placebo and the E. coli strains causing UTI at two follow-up visits were typed using pulsed-field gel electrophoresis (PFGE......). In the pivmecillinam treatment group PFGE showed that among patients having a negative urine culture at the first follow-up 77% (46/60) had a relapse with the primary infecting E. coli strain and 23% (14/60) had reinfection with a new E. coli strain at the second follow-up. Among patients having E. coli at the first...

  12. The performance of gel technetium-99m generator

    International Nuclear Information System (INIS)

    Liu Yishu

    2004-01-01

    Technetium-99m, as one of the important radionuclides in nuclear medical science, has been widely used for diseases diagnosis in both developed and developing countries for many years. Technetium-99m can be obtained from both fission-type and gel-type Tc-99m generator. Fission-type generator was prepared by Molybdenum-99 separated from fission products of uranium-235 and gel-type was prepared by irradiating nature MoO 3 in reactor, and a series of chemical and physical processes. This paper briefly describes the manufacturing technical process of gel-type Technetium-99 generator, including the preparation of target containing nature MoO 3 , the target irradiation in reactor, gel preparation, gel filtration and drying, dried gel cracking, generator loading and activity calibration of generator. The performances of gel-type Technetium-99m generator, such as elution efficiency, elution profile, the pH, Mo breakthrough, Zirconium content, radiochemical purity, radionuclidic purity, sterility and pyrogencity of eluate, are also expatiated in detail. Comparing with fission-type Technetium-99m generator, the defects of gel-type Technetium-99m generator are enumerated and their overcoming solutions are recommended in this paper. (author)

  13. Periodic mesoporous silica gels

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, M.T.; Martin, J.E.; Odinek, J.G. [and others

    1996-06-01

    We have synthesized monolithic particulate gels of periodic mesoporous silica by adding tetramethoxysilane to a homogeneous alkaline micellar precursor solution. The gels exhibit 5 characteristic length scales over 4 orders of magnitude: fractal domains larger than the particle size (>500 nm), particles that are {approximately}150 to 500 nm in diameter, interparticle pores that are on the order of the particle size, a feature in the gas adsorption measurements that indicates pores {approximately}10-50 nm, and periodic hexagonal arrays of {approximately}3 nm channels within each particle. The wet gel monoliths exhibit calculated densities as low as {approximately}0.02 g/cc; the dried and calcined gels have bulk densities that range from {approximately}0.3-0.5 g/cc. The materials possess large interparticle ({approximately}1.0-2.3 cc/g) and intraparticle ({approximately}0.6 cc/g) porosities.

  14. Gel purification of RNA.

    Science.gov (United States)

    Nilsen, Timothy W

    2013-02-01

    For many applications, including size selection of RNAs and purification of in vitro transcription products, it is necessary to purify RNAs on a denaturing gel. This procedure describes how to purify transcripts that have been synthesized in vitro. It is useful for labeled or unlabeled RNAs when sufficient mass is present. It can also be used to isolate small RNAs. In general, RNA purification by denaturing gel electrophoresis is practical only when the size of the desired RNA is 600 nucleotides or less.

  15. Conformance Improvement Using Gels

    Energy Technology Data Exchange (ETDEWEB)

    Seright, Randall S.; Schrader, Richard; II Hagstrom, John; Wang, Ying; Al-Dahfeeri, Abdullah; Gary, Raven; Marin; Amaury; Lindquist, Brent

    2002-09-26

    This research project had two objectives. The first objective was to identify gel compositions and conditions that substantially reduce flow through fractures that allow direct channeling between wells, while leaving secondary fractures open so that high fluid injection and production rates can be maintained. The second objective was to optimize treatments in fractured production wells, where the gel must reduce permeability to water much more than that to oil.

  16. Modelling of the inhomogeneous interior of polymer gels

    International Nuclear Information System (INIS)

    Shew, C-Y; Iwaki, Takafumi

    2006-01-01

    A simple model has been investigated to elucidate the mean squared displacement (MSD) of probe molecules in cross-linked polymer gels. In the model, we assume that numerous cavities distribute in the inhomogeneous interior of a gel, and probe molecules are confined within these cavities. The individual probe molecules trapped in a gel are treated as Brownian particles confined to a spherical harmonic potential. The harmonic potential is chosen to model the effective potential experienced by the probe particle in the cavity of a gel. Each field strength is corresponding to the characteristic of one type of effective cavity. Since the statistical distribution of different effective cavity sizes is unknown, several distribution functions are examined. Meanwhile, the calculated averaged MSDs are compared to the experimental data by Nisato et al (2000 Phys. Rev. E 61 2879). We find that the theoretical results of the MSD are sensitive to the shape of the distribution function. For low cross-linked gels, the best fit is obtained when the interior cavities of a gel follow a bimodal distribution. Such a result may be attributed to the presence of at least two distinct classes of cavity in gels. For high cross-linked gels, the cavities in the gel can be depicted by a single-modal uniform distribution function, suggesting that the range of cavity sizes becomes smaller. These results manifest the voids inside a gel, and the shape of distribution functions may provide the insight into the inhomogeneous interior of a gel

  17. STUDY OF THE INFLUENCE OF A GEL FORMER (THICKENER TYPE ON THE SORBTION KINETIC OF LONG-LIVING RADIONUCLIDES AND HEAVY METALS BY NATURAL ZELOLITE PASTE FROM AN AQUEOUS SOLUTION IN VITRO

    Directory of Open Access Journals (Sweden)

    Rybachuk, V. D.

    2018-04-01

    Full Text Available Introduction. The deterioration of the population health, due to the chemicalization of many aspects of life, requires the development and introduction of new healing technologies. One of the modern areas of efferent therapy is the oral administration of sorbents. An alternative to solid dosage forms, in some acute cases, is using enterosorbents in the form of paste, but in the Ukrainian pharmaceutical market, the range of such medicines has only several positions. The promising sources for the creation of such medicines is the natural zeolite. The aim of our study was to investigate the influence of a gel former (thickener type on the sorption kinetics of long-living 90Sr and 137Cs radionuclides and Pb2+ and Hg2+ heavy metals by natural zeolite paste from an aqueous solution in vitro. Materials and methods. As objects for the study we used experimental pastes containing 25% natural zeolite each and different gel formers: 7% silicon dioxide, 3% apple pectin and 0.5% sodium alginate. As sorption medium, we used solutions 7.25 mg/l Hg(NO32·H2O and 6.74 mg/l Pb(NO32 and radionuclide solutions 90Sr (1.8 × 107 Bq/dm3 and 137Cs (3.2 × 107 Bq/dm3. The sorption capacity for heavy metals was investigated by a limited volume method at pH = 2 and pH = 6. The concentration of lead was determined by atomic absorption spectroscopy (atomic absorption spectrophotometer C-115 PCS in a flame of acetylene-air (λ = 283.3 nm. The concentration of mercury was determined by the flame atomization method using mercury device PR-115 (λ = 253.7 nm. The sorption capacity of the samples against radionuclides was studied by the static sorption method at pH values 2.0, 5.5 and 8.0. The radioactivity were measured by a α-β-automaton NRR-610 "Tesla" radiometer. Concentration of ions and radioactivity of solutions were controlled after 0.5, 1, 2, 3, 4 and 5 hours of experiment. The equilibrium capacity of sorbents coefficient (Aeq., mg/g, the coefficient of sorption (Ks

  18. Active Polymer Gel Actuators

    Directory of Open Access Journals (Sweden)

    Shuji Hashimoto

    2010-01-01

    Full Text Available Many kinds of stimuli-responsive polymer and gels have been developed and applied to biomimetic actuators or artificial muscles. Electroactive polymers that change shape when stimulated electrically seem to be particularly promising. In all cases, however, the mechanical motion is driven by external stimuli, for example, reversing the direction of electric field. On the other hand, many living organisms can generate an autonomous motion without external driving stimuli like self-beating of heart muscles. Here we show a novel biomimetic gel actuator that can walk spontaneously with a wormlike motion without switching of external stimuli. The self-oscillating motion is produced by dissipating chemical energy of oscillating reaction. Although the gel is completely composed of synthetic polymer, it shows autonomous motion as if it were alive.

  19. 3D MR gel dosimetry with lung equivalent gel; 3D MR-Gel-Dosimetrie mit lungenaequivalentem Gel

    Energy Technology Data Exchange (ETDEWEB)

    Scherer, J.; Solleder, M.; Schiessl, I.; Bogner, L.; Herbst, M. [Klinik und Poliklinik fuer Strahlentherapie und Radioonkologie, Regensburg Univ. (Germany)

    1998-12-31

    The MR gel dosimetry is used to verify complex 3D treatment plans. Till now this method served only for dose evaluation in homogeneous phantoms. On the way to build a heterogeneous anthropomorphic gel phantom, a lung equivalent gel with the density 0.4 g/cm{sup 3} was developed. First experiments show a 1.55 times higher dose reponse in the low density gel (LD gel). The comparison of a dose distribution in a gel/LD gel/gel slab phantom with Monte Carlo calculations shows good agreement within 5%. More over the accuray of the measuring device magnetic resonance imager was studied in respect to the now exclusive digital image processing with the software MRD (MR dosimetry). Because of the dimensions of the Fricke gel phantom an artefact correction, based on the data from the unirradiated phantom proved to be essential. (orig.) [Deutsch] Die MR-Gel-Dosimetrie zur Verifikation komplexer 3D-Bestrahlungsplaene wurde bislang ausschliesslich in homogenen Phantomen durchgefuehrt. Auf dem Wege zum Bau eines inhomogenen Humanoid-Gel-Phantoms wurde ein lungenaequivalentes Gel mit der Dichte 0,4 g/cm{sup 3} entwickelt. Erste Messungen zeigen ein um den Faktor 1,55 hoeheres Ansprechvermoegen in dem low-density-Gel (LD-Gel). Der Vergleich einer gemessen Dosisverteilung in einem Gel/LD-Gel/Gel Schichtphantom als einfaches Thoraxmodell mit Monte-Carlo-Rechnungen zeigt eine gute Uebereinstimmung innerhalb 5%. Ausserdem wurden Untersuchungen zur Messgenauigkeit des Kernspintomographen im Rahmen der nun ausschliesslich digitalen Auswertung mit Hilfe des Programms MRD (MR-Dosimetrie) durchgefuehrt. Es zeigt sich, dass eine Artefaktkorrektur auf der Basis einer Messung des unbestrahlten Phantoms bei grossen Fricke-Gel-Phantomen notwendig ist. (orig.)

  20. Slow Release Of Reagent Chemicals From Gel Matrices

    Science.gov (United States)

    Debnam, William J.; Barber, Patrick G.; Coleman, James

    1988-01-01

    Procedure developed for slow release of reagent chemicals into solutions. Simple and inexpensive and not subject to failure of equipment. Use of toothpaste-type tube or pump dispenser conceivably provides more controlled technique for storage and dispensation of gel matrix. Possible uses include controlled, slow release of reagents in chemical reactions, crystal growth, space-flight experiments, and preformed gel medications from packets.

  1. A simple gel electrophoresis method for separating polyhedral gold nanoparticles

    Science.gov (United States)

    Kim, Suhee; Lee, Hye Jin

    2015-07-01

    In this paper, a simple approach to separate differently shaped and sized polyhedral gold nanoparticles (NPs) within colloidal solutions via gel electrophoresis is described. Gel running parameters for separating efficiently gold NPs including gel composition, added surfactant types and applied voltage were investigated. The plasmonic properties and physical structure of the separated NPs extracted from the gel matrix were then investigated using transmission electron microscopy (TEM) and UV-vis spectrophotometry respectively. Data analysis revealed that gel electrophoresis conditions of a 1.5 % agarose gel with 0.1 % sodium dodecyl sulfate (SDS) surfactant under an applied voltage of 100 V resulted in the selective isolation of ~ 50 nm polyhedral shaped gold nanoparticles. Further efforts are underway to apply the method to purify biomolecule-conjugated polyhedral Au NPs that can be readily used for NP-enhanced biosensing platforms.

  2. based gel polymer electrolytes

    Indian Academy of Sciences (India)

    Bull. Mater. Sci., Vol. 29, No. 7, December 2006, pp. 673–678. © Indian Academy of Sciences. 673. Investigation on poly (vinylidene fluoride) based gel polymer electrolytes ... (Alamgir and Abraham 1993; Sukeshini et al 1996; Ra- jendran and Uma ... Yang et al 1996; Ramesh and Arof 2001) and such elec- trolytes exhibit ...

  3. gel template method

    Indian Academy of Sciences (India)

    TiO2 nanotubes have been synthesized by sol–gel template method using alumina membrane. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, UV absorption spectrum and X-ray diffraction techniques have been used to investigate the structure, morphology and optical ...

  4. Pulsed-field gel electrophoresis typing of Escherichia coli strains from samples collected before and after pivmecillinam or placebo treatment of uncomplicated community-acquired urinary tract infection in women

    DEFF Research Database (Denmark)

    Ejrnaes, Karen; Sandvang, Dorthe; Lundgren, Bettina

    2006-01-01

    The primary infecting Escherichia coli strains from 156 women with community-acquired uncomplicated urinary tract infection (UTI) randomized to pivmecillinam or placebo and the E. coli strains causing UTI at two follow-up visits were typed using pulsed-field gel electrophoresis (PFGE......). In the pivmecillinam treatment group PFGE showed that among patients having a negative urine culture at the first follow-up 77% (46/60) had a relapse with the primary infecting E. coli strain and 23% (14/60) had reinfection with a new E. coli strain at the second follow-up. Among patients having E. coli at the first...... follow-up PFGE showed that 80% (32/40) had persistence with the primary infecting E. coli strain, 15% (6/40) had reinfection with a new E. coli strain, and 5% (2/40) had different E. coli strains at the two follow-up visits (one had reinfection followed by relapse, and the other had persistence followed...

  5. Pulsed-field gel electrophoresis typing of Eschericia coli strains from samples collected before and after pivmecillinam or placebo treatment of uncomplicated community-acquired urinary tract infection in women

    DEFF Research Database (Denmark)

    Ejrnæs, K; Sandvang, D; Lundgren, Bettina

    2006-01-01

    The primary infecting Escherichia coli strains from 156 women with community-acquired uncomplicated urinary tract infection (UTI) randomized to pivmecillinam or placebo and the E. coli strains causing UTI at two follow-up visits were typed using pulsed-field gel electrophoresis (PFGE......). In the pivmecillinam treatment group PFGE showed that among patients having a negative urine culture at the first follow-up 77% (46/60) had a relapse with the primary infecting E. coli strain and 23% (14/60) had reinfection with a new E. coli strain at the second follow-up. Among patients having E. coli at the first...... follow-up PFGE showed that 80% (32/40) had persistence with the primary infecting E. coli strain, 15% (6/40) had reinfection with a new E. coli strain, and 5% (2/40) had different E. coli strains at the two follow-up visits (one had reinfection followed by relapse, and the other had persistence followed...

  6. On the photo-luminescence properties of sol–gel derived undoped and Dy{sup 3+} ion doped nanocrystalline Scheelite type AMoO{sub 4} (A = Ca, Sr and Ba)

    Energy Technology Data Exchange (ETDEWEB)

    Jena, Paramananda [Department of Physics, Pondicherry University, Pondicherry 605014 (India); Gupta, Santosh K., E-mail: santufrnd@gmail.com [Radiochemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Natarajan, V. [Radiochemistry Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Padmaraj, O. [Department of Physics, Pondicherry University, Pondicherry 605014 (India); Satyanarayana, N., E-mail: nallanis2011@gmail.com [Department of Physics, Pondicherry University, Pondicherry 605014 (India); Venkateswarlu, M. [R & D Amara Raja Batteries Ltd., Karakambadi 517501, AP (India)

    2015-04-15

    Nanocrystalline Scheelite type Dy doped AMoO{sub 4} [where A = Ba, Sr and Ca] samples were prepared by acrylamide assisted sol–gel process and characterized by XRD, FT-Raman, FTIR, SEM and photoluminescence (PL). PL of undoped sample shows blue/green emission in CaMoO{sub 4} and SrMoO{sub 4} but multicolour visible emission leading to near white light in BaMoO{sub 4} nanoparticles; the origin of which is explained. It was observed that on doping 0.5 mol% of Dy{sup 3+} in molybdate samples complete energy transfer takes place in case of SrMoO{sub 4} and BaMoO{sub 4}, but host contributed substantially in Dy doped BaMoO{sub 4} sample, resulting in biexponential decay. It was also observed that symmetry around Dy{sup 3+} decreases as the size of alkaline earth ion increases. Due to combined blue, yellow and red colour emission in dysprosium doped sample; all samples showed near white light emission under UV and near UV excitation.

  7. Fluid diversion and sweep improvement with chemical gels in oil recovery processes

    Energy Technology Data Exchange (ETDEWEB)

    Seright, F.S.; Martin, F.D.

    1991-04-01

    The objectives of this project are to identify the mechanisms by which gel treatments divert fluids in reservoirs and to establish where and how gel treatments are best applied. Several different types of gelants are being examined. This research is directed at gel applications in water injection wells, in production wells, and in high-pressure gas floods. The work will establish how the flow properties of gels and gelling agents are influenced by permeability, lithology, and wettability. Other goals include determining the proper placement of gelants, the stability of in-place gels, and the types of gels required for the various oil recovery processes and for different scales of reservoir heterogeneity. This report describes progress made during the first year of this three-year study the following tasks: gel screening studies; impact of gelation pH, rock permeability, and lithology on the performance of a monomer-based gel; preliminary study of the permeability reduction for CO{sub 2} and water using a resorcinol-formaldehyde gel; preliminary study of permeability reduction for oil and water using a resorcinol-formaldehyde gel; rheology of Cr(III)-xanthan gel and gelants in porous media; impact of diffusion, dispersion, and viscous fingering on gel placement in injection wells; examination of flow-profile changes for field applications of gel treatments in injection wells; and placement of gels in production wells. Papers have been indexed separately for inclusion on the data base.

  8. Species Identification and Strain Typing of Staphylococcus agnetis and Staphylococcus hyicus Isolates from Bovine Milk by Use of a Novel Multiplex PCR Assay and Pulsed-Field Gel Electrophoresis.

    Science.gov (United States)

    Adkins, P R F; Middleton, J R; Calcutt, M J; Stewart, G C; Fox, L K

    2017-06-01

    Staphylococcus hyicus and Staphylococcus agnetis are two coagulase-variable staphylococcal species that can be isolated from bovine milk and are difficult to differentiate. The objectives of this study were to characterize isolates of bovine milk origin from a collection that had previously been characterized as coagulase-positive S. hyicus based on phenotypic species identification methods and to develop a PCR-based method for differentiating S. hyicus , S. agnetis , and Staphylococcus aureus Isolates ( n = 62) were selected from a previous study in which milk samples were collected from cows on 15 dairy herds. Isolates were coagulase tested and identified to the species level using housekeeping gene sequencing. A multiplex PCR to differentiate S. hyicus , S. agnetis , and S. aureus was developed. Pulsed-field gel electrophoresis was conducted to strain type the isolates. Based on gene sequencing, 44/62 of the isolates were determined to be either S. agnetis ( n = 43) or S. hyicus ( n = 1). Overall, 88% (37/42) of coagulase-positive S. agnetis isolates were found to be coagulase positive at 4 h. The herd-level prevalence of coagulase-positive S. agnetis ranged from 0 to 2.17%. Strain typing identified 23 different strains. Six strains were identified more than once and from multiple cows within the herd. Three strains were isolated from cows at more than one time point, with 41 to 264 days between samplings. These data suggest that S. agnetis is likely more prevalent on dairy farms than S. hyicus Also, some S. agnetis isolates in this study appeared to be contagious and associated with persistent infections. Copyright © 2017 American Society for Microbiology.

  9. Biopolymer gels containing fructooligosaccharides.

    Science.gov (United States)

    Silva, Karen Cristina Guedes; Sato, Ana Carla Kawazoe

    2017-11-01

    The influence of the addition of fructooligosaccharide (FOS) in an external gelated alginate/gelatin biopolymer matrix, was evaluated in order to produce biopolymeric structures with functional effects. Solutions were characterized regarding their rheological properties, macrogels regarding their microstructure and mechanical properties and microgels were characterized in relation to their particle size distribution and morphology. Close relationship was found between the microstructure, rheological and mechanical properties of the biopolymeric systems. An increased viscosity and accentuated elastic and pseudoplastic behavior were associated to denser microstructures. The FOS addition caused changes in the evaluated properties, resulting in more cohesive structures, with smaller pores and higher viscosity, compared to alginate-gelatin gels. The addition of 3% FOS to biopolymeric system provided an optimal condition, allowing the formation of stronger gels, with smaller pores and beads with smaller sizes, indicating the potential use of these functional systems as texture modifiers or encapsulation systems. Copyright © 2017 Elsevier Ltd. All rights reserved.

  10. Elaboration et caractérisations de nanocristaux organiques fluorescents insérés en coquille sol-gel : vers le développement d'un nouveau type d'agent imageant

    OpenAIRE

    Philippot, Cécile

    2010-01-01

    We demonstrated the feasibility and the reproducibility of our method of one-step elaboration of organic nanocrystals in sol-gel shell obtained by atomization, by using various sort of organic molecules, solvent and sol-gel matrices. The use of different techniques of characterization (scanning electronic microscopy, one and two photons luminescence spectroscopy) allowed to optimized the conditions of elaboration to obtain hybrid nanoparticles of small sizes, with a maximum of fluorophore, hi...

  11. Chiromagnetic nanoparticles and gels

    Science.gov (United States)

    Yeom, Jihyeon; Santos, Uallisson S.; Chekini, Mahshid; Cha, Minjeong; de Moura, André F.; Kotov, Nicholas A.

    2018-01-01

    Chiral inorganic nanostructures have high circular dichroism, but real-time control of their optical activity has so far been achieved only by irreversible chemical changes. Field modulation is a far more desirable path to chiroptical devices. We hypothesized that magnetic field modulation can be attained for chiral nanostructures with large contributions of the magnetic transition dipole moments to polarization rotation. We found that dispersions and gels of paramagnetic Co3O4 nanoparticles with chiral distortions of the crystal lattices exhibited chiroptical activity in the visible range that was 10 times as strong as that of nonparamagnetic nanoparticles of comparable size. Transparency of the nanoparticle gels to circularly polarized light beams in the ultraviolet range was reversibly modulated by magnetic fields. These phenomena were also observed for other nanoscale metal oxides with lattice distortions from imprinted amino acids and other chiral ligands. The large family of chiral ceramic nanostructures and gels can be pivotal for new technologies and knowledge at the nexus of chirality and magnetism.

  12. Topological characteristics of model gels

    International Nuclear Information System (INIS)

    Miller, Mark A; Hansen, Jean-Pierre; Blaak, Ronald

    2010-01-01

    The Euler characteristic of an object is a topological invariant determined by the number of handles and holes that it contains. Here, we use the Euler characteristic to profile the topology of model three-dimensional gel-forming fluids as a function of increasing length scale. These profiles act as a 'topological fingerprint' of the structure, and can be interpreted in terms of three types of topological events. As model fluids we have considered a system of dipolar dumbbells, and suspensions of adhesive hard spheres with isotropic and patchy interactions in turn. The correlation between the percolation threshold and the length scale on which the Euler characteristic passes through zero is examined and found to be system-dependent. A scheme for the efficient calculation of the Euler characteristic with and without periodic boundary conditions is described.

  13. Klebsiella Typing

    DEFF Research Database (Denmark)

    Hansen, D S; Skov, R; Benedí, J.V.

    2002-01-01

    unit (NICU) were K-typed by countercurrent immunoelectrophoresis (CCIE), O-typed by an inhibition enzyme-linked immunosorbent assay method, and typed by pulsed-field gel electrophoresis (PFGE) using the restriction enzyme XbaI. RESULTS: Typing data for the 104 bacteremia isolates were compared......OBJECTIVE: To compare pulsed-field gel electrophoresis (PFGE) typing and O:K-serotyping of Klebsiella in two different epidemiological settings. METHODS: One hundred and four bacteremia isolates without known epidemiological relation and 47 isolates from an outbreak in a neonatal intensive care...

  14. Investigation of the Peroxovanadate Sol-Gel Process and Characterization of the Gels

    Energy Technology Data Exchange (ETDEWEB)

    Fontenot, Craig Joseph [Iowa State Univ., Ames, IA (United States)

    2001-01-01

    In general, the peroxovanadate solution sol-gel process can be thought of as consisting of two parts: (1) the decomposition of the peroxo species and (2) cation hydrolysis leading to gelation. By controlling the synthesis conditions, both layered and amorphous compounds can be created. However, the type of water coordination observed in these gels was found to be identical no matter what the long-range order. The current work clarified many of the discrepancies found in the literature and offered much new valuable information. Highlights include the types of vanadium environments present at various stages of hydration, the role of adsorbed water, oxygen exchange from adsorbed water into the gel sites, and the ability to create metastable VMoO solid solution phases. These results could have a variety of impacts on future catalysis research.

  15. Radiotherapy gel dosimetry

    International Nuclear Information System (INIS)

    Baldock, C.

    2002-01-01

    shapes and sizes while sparing normal tissue. The situation is further complicated if the normal tissues are critical organs or are particularly sensitive to radiation. Radiotherapy techniques employed to obtain a closer conformation of the dose distribution to the tumour volume are referred to as conformal radiotherapy techniques. The clinical implementation of conformal therapy has been delayed by limitations in the verification of conformal dose distributions calculated by treatment planning systems prior to the irradiation of the patient and the verification of complex treatments during its delivery to the patient. There are several aspects of conformal therapy that complicate dose verification. To achieve the dose distributions conforming to complex 3D volumes, high dose gradients arise in the treatment volume. Further, overdose or underdose regions can exist when separate radiation fields are used to deliver additional radiation. These aspects require that practical dose measurement (dosimetry) techniques be able to integrate dose over time and easily measure dose distributions in 3D with high spatial resolution. Traditional dosimeters, such as ion chambers, thermoluminescent dosimeters and radiographic film do not fulfil these requirements. Novel gel dosimetry techniques are being developed in which dose distributions can potentially be determined in vitro in 3D using anthropomorphic phantoms to simulate a clinically irradiated situation. As long ago as the 1950's, radiation-induced colour change in dyes was used to investigate radiation doses in gels. It was subsequently shown that radiation induced changes in nuclear magnetic resonance (NMR) relaxation properties of gels infused with conventional Fricke dosimetry solutions could be measured using magnetic resonance imaging (MRI). In Fricke gels, Fe 2+ ions in ferrous sulphate solutions are usually dispersed throughout a gelatin, agarose or PVA matrix. Radiation-induced changes in the dosimeters are considered to

  16. Electrochemical behavior of ionically crosslinked polyampholytic gel electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Wanyu; Tang, Haitao; Ou, Ziwei; Wang, Hong; Yang, Yajiang [Department of Chemistry, Huazhong University of Science and Technology, Wuhan 430074 (China)

    2007-12-31

    An ionic complex of anionic and cationic monomers was obtained by protonation of (N,N-diethylamino)ethylmethacrylate (DEA) with acrylic acid (AAc). Free radical copolymerization of the ionic complex and acrylamide (AAm), yielded the ionically crosslinked polyampholytic gel electrolytes [poly(AAc-DEA-AAm), designated as PADA] using two types of organic solvents containing a lithium salt. The PADA gel electrolyte exhibited good thermal stability shown by the DSC thermogram. The impedance analysis at temperatures ranging from -30 to 75 C indicated that the ionic conductivities of the PADA gel electrolytes were rather close to those of liquid electrolytes. The temperature dependence of the ionic conductivities was found to be in accord with the Arrhenius equation. Moreover, the ionic conductivities of PADA gel electrolytes increased with an increase of the molar ratios of cationic/anionic monomers. The ionic conductivities of PADA gels prepared in solvent mixtures of propylene carbonate, ethyl methyl ether and dioxolane (3:1:1, v/v) were higher than those of PADA gels prepared in propylene carbonate only. Significantly, the ionic conductivities of two kinds of PADA gel electrolytes were in the range of 10{sup -3} and 10{sup -4} S cm{sup -1} even at -30 C. The electrochemical windows of PADA gel electrolytes measured by cyclic voltammetry were in the range from -1 V to 4.5 V. (author)

  17. Electrochemical behavior of ionically crosslinked polyampholytic gel electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Chen Wanyu; Tang Haitao; Ou Ziwei; Wang Hong [Department of Chemistry, Huazhong University of Science and Technology, Wuhan 430074 (China); Yang Yajiang [Department of Chemistry, Huazhong University of Science and Technology, Wuhan 430074 (China)], E-mail: yjyang@mail.hust.edu.cn

    2007-12-31

    An ionic complex of anionic and cationic monomers was obtained by protonation of (N,N-diethylamino)ethylmethacrylate (DEA) with acrylic acid (AAc). Free radical copolymerization of the ionic complex and acrylamide (AAm), yielded the ionically crosslinked polyampholytic gel electrolytes [poly(AAc-DEA-AAm), designated as PADA] using two types of organic solvents containing a lithium salt. The PADA gel electrolyte exhibited good thermal stability shown by the DSC thermogram. The impedance analysis at temperatures ranging from -30 to 75 deg. C indicated that the ionic conductivities of the PADA gel electrolytes were rather close to those of liquid electrolytes. The temperature dependence of the ionic conductivities was found to be in accord with the Arrhenius equation. Moreover, the ionic conductivities of PADA gel electrolytes increased with an increase of the molar ratios of cationic/anionic monomers. The ionic conductivities of PADA gels prepared in solvent mixtures of propylene carbonate, ethyl methyl ether and dioxolane (3:1:1, v/v) were higher than those of PADA gels prepared in propylene carbonate only. Significantly, the ionic conductivities of two kinds of PADA gel electrolytes were in the range of 10{sup -3} and 10{sup -4} S cm{sup -1} even at -30 deg. C. The electrochemical windows of PADA gel electrolytes measured by cyclic voltammetry were in the range from -1 V to 4.5 V.

  18. Gel polymer electrolytes for batteries

    Science.gov (United States)

    Balsara, Nitash Pervez; Eitouni, Hany Basam; Gur, Ilan; Singh, Mohit; Hudson, William

    2014-11-18

    Nanostructured gel polymer electrolytes that have both high ionic conductivity and high mechanical strength are disclosed. The electrolytes have at least two domains--one domain contains an ionically-conductive gel polymer and the other domain contains a rigid polymer that provides structure for the electrolyte. The domains are formed by block copolymers. The first block provides a polymer matrix that may or may not be conductive on by itself, but that can soak up a liquid electrolyte, thereby making a gel. An exemplary nanostructured gel polymer electrolyte has an ionic conductivity of at least 1.times.10.sup.-4 S cm.sup.-1 at 25.degree. C.

  19. Thoria sol-gel processes

    International Nuclear Information System (INIS)

    Matthews, R.B.

    1978-10-01

    Alternate fuel fabrication techniques are being developed at WNRE as part of the thorium fuel cycle program. The sol-gel techniques are attractive and this report assembles and summarizes information relating to thoria sol-gel fuels. Some background information on the behaviour and advantages of sol-gel fuel forms is presented, followed by a review of relevant colloid chemistry and an explanation of the fundamental steps of sol-gel processes. Finally, several variants to the basic process are reviewed and evaluated. (author)

  20. Radiotherapy gel dosimetry: a review

    International Nuclear Information System (INIS)

    Baldock, C.

    2003-01-01

    Radiation therapy or radiotherapy is a common form of cancer treatment. Recent advances in radiotherapy such as intensity modulated radiation therapy indicate that treatment outcomes may be improved. The principle limitation of these more advanced techniques of radiation therapy is the ability to quantify the absorbed radiation dose to the tumour which is related to the 3- dimensional geometry of the tumour. The main advances in 3-dimensional radiation dosimetry are the development of radiation sensitive polymer gel dosimeters. The use of radiation sensitive gels for radiation dosimetry in cancer therapy was first suggested in the 1950s. It was subsequently shown in 1984 that radiation induced changes in nuclear magnetic resonance relaxation properties of gels infused with conventional Fricke dosimetry solutions could be measured. Due to diffusion-related limitations in the use of Fricke gels, alternative polymer gel dosimeters were subsequently suggested in 1992. Since then, both magnetic resonance and optical imaging techniques have been used to evaluate polymer gel dosimeters to produce three-dimensional radiation dose distributions. More recently the uses of x-ray computer tomography and vibrational spectroscopy have also been demonstrated as valuable techniques in the evaluation of these dosimetry gels. Although not yet used routinely clinically, applications of these radiologically soft-tissue equivalent gel dosimeters have been shown to have great potential in the evaluation of complex radiation dose distributions. A review of 3-dimensional radiotherapy gel dosimetry is presented

  1. Azelaic acid (15% gel) in the treatment of acne rosacea.

    Science.gov (United States)

    Gupta, Aditya K; Gover, Melissa D

    2007-05-01

    In December of 2002, the FDA approved azelaic acid 15% gel for the topical treatment of inflammatory papules and pustules of mild to moderate rosacea. Azelaic acid is a saturated dicarboxylic acid, which is naturally occurring and has been used in the treatment of rosacea, acne, and melasma. The 15% gel has a high efficacy and is generally well tolerated, with the local irritation (burning, stinging, itching, and scaling) being typically mild and transient. Azelaic acid 15% gel is considered effective and safe as a therapy for inflammatory papulo-pustular rosacea and is suitable for use on all skin types.

  2. Rheology and structure of milk protein gels

    NARCIS (Netherlands)

    Vliet, van T.; Lakemond, C.M.M.; Visschers, R.W.

    2004-01-01

    Recent studies on gel formation and rheology of milk gels are reviewed. A distinction is made between gels formed by aggregated casein, gels of `pure` whey proteins and gels in which both casein and whey proteins contribute to their properties. For casein' whey protein mixtures, it has been shown

  3. Gel placement in porous media

    NARCIS (Netherlands)

    F.J. Vermolen; J. Bruining; C.J. van Duijn (Hans)

    1999-01-01

    textabstractIn this paper we analyse advective transport of polymers, crosslinkers and gel, taking into account non-equilibrium gelation, gel adsorption and crosslinker precipitation. In absence of diffusion/dispersion the resulting model consists of hyperbolic transport-reaction equations. These

  4. Gel Fabrication of Molybdenum “Beads”

    Energy Technology Data Exchange (ETDEWEB)

    Lowden, Richard Andrew [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division; Armstrong, Beth L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division; Cooley, Kevin M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division

    2016-11-01

    Spherical molybdenum particles or “beads” of various diameters are of interest as feedstock materials for the additive manufacture of targets and assemblies used in the production of 99Mo medical isotopes using accelerator technology. Small metallic beads or ball bearings are typically fabricated from wire; however, small molybdenum spheres cannot readily be produced in this manner. Sol-gel processes are often employed to produce small dense microspheres of metal oxides across a broad diameter range that in the case of molybdenum could be reduced and sintered to produce metallic spheres. These Sol-gel type processes were examined for forming molybdenum oxide beads; however, the molybdenum trioxide was chemically incompatible with commonly used gelation materials. As an alternative, an aqueous alginate process being assessed for the fabrication of oxide spheres for catalyst applications was employed to form molybdenum trioxide beads that were successfully reduced and sintered to produce small molybdenum spheres.

  5. Development of strippable gel for surface decontamination applications

    International Nuclear Information System (INIS)

    Banerjee, D.; Sandhya, U.; Khot, S.A.; Srinivas, C.

    2015-07-01

    Strippable gels are an attractive option for decontamination of surfaces particularly when materials are to be reused after decontamination. The process in general results in good decontamination performance with minimal secondary waste generation. This paper reports on development of strippable gel formulation using polyvinyl alcohol as the gel former. Peeling behavior of the gel film improved when glycerol was used as plasticizer. Incorporation of decontaminating agents is essential for the gel to be effective, so a number of decontaminating agents were screened based on their miscibility with the gel, smooth peeling, and good decontamination performance. Based on this study, a strippable gel, ‘INDIGEL’ was formulated as a potential candidate for surface decontamination applications. Extensive trials on evaluation of decontamination performance of Indigel were done on simulated surfaces like stainless steel tray, stainless steel fume hood, PVC floor, granite and ceramic table tops. Results show that Indigel is highly effective for decontamination of surfaces contaminated with all types of radionuclides. Simplicity of its use coupled with good decontamination ability will find application in nuclear and other chemical industries. (author)

  6. Chemical Gel for Surface Decontamination

    International Nuclear Information System (INIS)

    Jung, Chong Hun; Moon, J. K.; Won, H. J.; Lee, K. W.; Kim, C. K.

    2010-01-01

    Many chemical decontamination processes operate by immersing components in aggressive chemical solutions. In these applications chemical decontamination technique produce large amounts of radioactive liquid waste. Therefore it is necessary to develop processes using chemical gels instead of chemical solutions, to avoid the well-known disadvantages of chemical decontamination techniques while retaining their high efficiency. Chemical gels decontamination process consists of applying the gel by spraying it onto the surface of large area components (floors, walls, etc) to be decontaminated. The gel adheres to any vertical or complex surface due to their thixotropic properties and operates by dissolving the radioactive deposit, along with a thin layer of the gel support, so that the radioactivity trapped at the surface can be removed. Important aspects of the gels are that small quantities can be used and they show thixitropic properties : liquid during spraying, and solid when stationary, allowing for strong adherence to surfaces. This work investigates the decontamination behaviors of organic-based chemical gel for SS 304 metallic surfaces contaminated with radioactive materials

  7. Denaturing gradient gel electrophoresis

    International Nuclear Information System (INIS)

    Kocherginskaya, S.A.; Cann, I.K.O.; Mackie, R.I.

    2005-01-01

    It is worthwhile considering that only some 30 species make up the bulk of the bacterial population in human faeces at any one time based on the classical cultivation-based approach. The situation in the rumen is similar. Thus, it is practical to focus on specific groups of interest within the complex community. These may be the predominant or the most active species, specific physiological groups or readily identifiable (genetic) clusters of phylogenetically related organisms. Several 16S rDNA fingerprinting techniques can be invaluable for selecting and monitoring sequences or phylogenetic groups of interest and are described below. Over the past few decades, considerable attention was focussed on the identification of pure cultures of microbes on the basis of genetic polymorphisms of DNA encoding rRNA such as ribotyping, amplified fragment length polymorphism and randomly amplified polymorphic DNA. However, many of these methods require prior cultivation and are less suitable for use in analysis of complex mixed populations although important in describing cultivated microbial diversity in molecular terms. Much less attention was given to molecular characterization of complex communities. In particular, research into diversity and community structure over time has been revolutionized by the advent of molecular fingerprinting techniques for complex communities. Denaturing or temperature gradient gel electrophoresis (DGGE/TGGE) methods have been successfully applied to the analysis of human, pig, cattle, dog and rodent intestinal populations

  8. Agarose gel electrophoresis for the separation of DNA fragments.

    Science.gov (United States)

    Lee, Pei Yun; Costumbrado, John; Hsu, Chih-Yuan; Kim, Yong Hoon

    2012-04-20

    Agarose gel electrophoresis is the most effective way of separating DNA fragments of varying sizes ranging from 100 bp to 25 kb(1). Agarose is isolated from the seaweed genera Gelidium and Gracilaria, and consists of repeated agarobiose (L- and D-galactose) subunits(2). During gelation, agarose polymers associate non-covalently and form a network of bundles whose pore sizes determine a gel's molecular sieving properties. The use of agarose gel electrophoresis revolutionized the separation of DNA. Prior to the adoption of agarose gels, DNA was primarily separated using sucrose density gradient centrifugation, which only provided an approximation of size. To separate DNA using agarose gel electrophoresis, the DNA is loaded into pre-cast wells in the gel and a current applied. The phosphate backbone of the DNA (and RNA) molecule is negatively charged, therefore when placed in an electric field, DNA fragments will migrate to the positively charged anode. Because DNA has a uniform mass/charge ratio, DNA molecules are separated by size within an agarose gel in a pattern such that the distance traveled is inversely proportional to the log of its molecular weight(3). The leading model for DNA movement through an agarose gel is "biased reptation", whereby the leading edge moves forward and pulls the rest of the molecule along(4). The rate of migration of a DNA molecule through a gel is determined by the following: 1) size of DNA molecule; 2) agarose concentration; 3) DNA conformation(5); 4) voltage applied, 5) presence of ethidium bromide, 6) type of agarose and 7) electrophoresis buffer. After separation, the DNA molecules can be visualized under uv light after staining with an appropriate dye. By following this protocol, students should be able to: Understand the mechanism by which DNA fragments are separated within a gel matrix Understand how conformation of the DNA molecule will determine its mobility through a gel matrix Identify an agarose solution of appropriate

  9. Fluoride Rinses, Gels and Foams

    DEFF Research Database (Denmark)

    Twetman, Svante; Keller, Mette K

    2016-01-01

    AIM: The aim of this conference paper was to systematically review the quality of evidence and summarize the findings of clinical trials published after 2002 using fluoride mouth rinses, fluoride gels or foams for the prevention of dental caries. METHODS: Relevant papers were selected after...... (6 on fluoride mouth rinse, 10 on fluoride gel and 3 on fluoride foam); 6 had a low risk of bias while 2 had a moderate risk. All fluoride measures appeared to be beneficial in preventing crown caries and reversing root caries, but the quality of evidence was graded as low for fluoride mouth rinse......, moderate for fluoride gel and very low for acidulated fluoride foam. No conclusions could be drawn on the cost-effectiveness. CONCLUSIONS: This review, covering the recent decade, has further substantiated the evidence for a caries-preventive effect of fluoride mouth rinse, fluoride gel and foam...

  10. Injectable gels for tissue engineering.

    Science.gov (United States)

    Gutowska, A; Jeong, B; Jasionowski, M

    2001-08-01

    Recently, tissue engineering approaches using injectable, in situ gel forming systems have been reported. In this review, the gelation processes and several injectable systems that exhibit in situ gel formation at physiological conditions are discussed. Applications of selected injectable systems (alginate, chitosan, hyaluronan, polyethylene oxide/polypropylene oxide) in tissue engineering are also described. Injectable polymer formulation can gel in vivo in response to temperature change (thermal gelation), pH change, ionic cross-linking, or solvent exchange. Kinetics of gelation is directly affected by its mechanism. Injectable formulations offer specific advantages over preformed scaffolds such as: possibility of a minimally invasive implantation, an ability to fill a desired shape, and easy incorporation of various therapeutic agents. Several factors need to be considered before an injectable gel can be selected as a candidate for tissue engineering applications. Apart from tissue-specific cell-matrix interactions, the following gel properties need to be considered: gelation kinetics, matrix resorption rate, possible toxicity of degradation products and their elimination routes, and finally possible interference of the gel matrix with histogenesis. Copyright 2001 Wiley-Liss, Inc.

  11. Bleach gel: a simple agarose gel for analyzing RNA quality.

    Science.gov (United States)

    Aranda, Patrick S; LaJoie, Dollie M; Jorcyk, Cheryl L

    2012-01-01

    RNA-based applications requiring high-quality, non-degraded RNA are a foundational element of many research studies. As such, it is paramount that the integrity of experimental RNA is validated prior to cDNA synthesis or other downstream applications. In the absence of expensive equipment such as microfluidic electrophoretic devices, and as an alternative to the costly and time-consuming standard formaldehyde gel, RNA quality can be quickly analyzed by adding small amounts of commercial bleach to TAE buffer-based agarose gels prior to electrophoresis. In the presence of low concentrations of bleach, the secondary structure of RNA is denatured and potential contaminating RNases are destroyed. Because of this, the 'bleach gel' is a functional approach that addresses the need for an inexpensive and safe way to evaluate RNA integrity and will improve the ability of researchers to rapidly analyze RNA quality. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Comparative Skeletal Muscle Proteomics Using Two-Dimensional Gel Electrophoresis

    Science.gov (United States)

    Murphy, Sandra; Dowling, Paul; Ohlendieck, Kay

    2016-01-01

    The pioneering work by Patrick H. O’Farrell established two-dimensional gel electrophoresis as one of the most important high-resolution protein separation techniques of modern biochemistry (Journal of Biological Chemistry 1975, 250, 4007–4021). The application of two-dimensional gel electrophoresis has played a key role in the systematic identification and detailed characterization of the protein constituents of skeletal muscles. Protein changes during myogenesis, muscle maturation, fibre type specification, physiological muscle adaptations and natural muscle aging were studied in depth by the original O’Farrell method or slightly modified gel electrophoretic techniques. Over the last 40 years, the combined usage of isoelectric focusing in the first dimension and sodium dodecyl sulfate polyacrylamide slab gel electrophoresis in the second dimension has been successfully employed in several hundred published studies on gel-based skeletal muscle biochemistry. This review focuses on normal and physiologically challenged skeletal muscle tissues and outlines key findings from mass spectrometry-based muscle proteomics, which was instrumental in the identification of several thousand individual protein isoforms following gel electrophoretic separation. These muscle-associated protein species belong to the diverse group of regulatory and contractile proteins of the acto-myosin apparatus that forms the sarcomere, cytoskeletal proteins, metabolic enzymes and transporters, signaling proteins, ion-handling proteins, molecular chaperones and extracellular matrix proteins. PMID:28248237

  13. Crystal growth of proteins, nucleic acids, and viruses in gels.

    Science.gov (United States)

    Lorber, Bernard; Sauter, Claude; Théobald-Dietrich, Anne; Moreno, Abel; Schellenberger, Pascale; Robert, Marie-Claire; Capelle, Bernard; Sanglier, Sarah; Potier, Noëlle; Giegé, Richard

    2009-11-01

    Medium-sized single crystals with perfect habits and no defect producing intense and well-resolved diffraction patterns are the dream of every protein crystallographer. Crystals of biological macromolecules possessing these characteristics can be prepared within a medium in which mass transport is restricted to diffusion. Chemical gels (like polysiloxane) and physical gels (such as agarose) provide such an environment and are therefore suitable for the crystallisation of biological macromolecules. Instructions for the preparation of each type of gel are given to urge crystal growers to apply diffusive media for enhancing crystallographic quality of their crystals. Examples of quality enhancement achieved with silica and agarose gels are given. Results obtained with other substances forming gel-like media (such as lipidic phases and cellulose derivatives) are presented. Finally, the use of gels in combination with capillary tubes for counter-diffusion experiments is discussed. Methods and techniques implemented with proteins can also be applied to nucleic acids and nucleoprotein assemblies such as viruses.

  14. Development of lidocaine gels for enhanced local anesthetic action.

    Science.gov (United States)

    Shin, Sang-Chul; Cho, Cheong-Weon; Yang, Kyu-Ho

    2004-12-09

    In relieving local pains, lidocaine, one of ester type local anesthetics, has been used. To develop the lidocaine gels of enhanced local anesthetic effects, hydroxypropyl methylcellulose (HPMC) based bioadhesive polymer gel containing an enhancer was formulated. As the drug concentration in the gels increased up to 3%, the permeation rate of drug linearly increased, thereafter reaching a plateau. As the temperature of surrounding solutions increased, the permeation of drug increased. The activation energy of drug permeation was 3.29 kcal/mol for lidocaine. The permeation rate of drug through skin was studied using various enhancers, such as glycols, non-ionic surfactants, and bile salts. Among the enhancers studied, diethylene glycol showed the greatest enhancing effects on drug permeation through skin. The analgesic activity was examined using a tail-flick analgesimeter. In the area under the efficacy curve (AUEC) of the rat-tail flick tests, lidocaine gel containing diethylene glycol showed about 3.89-fold increase in analgesic activity compared with the control. The addition of vasoconstrictor in the gels prolonged the analgesic effects. The result of this study supports that the bioadhesive gel with efficient anesthetic effect could be developed using HPMC with combination of enhancer and vasoconstrictor.

  15. On the layer structure of vanadium pentoxide gels. Comment on `molecular dynamic simulation of the vanadium pentoxide gel host`

    Energy Technology Data Exchange (ETDEWEB)

    Yao, Takeshi [Department of Fundamental Energy Science, Graduate School of Energy Sciences, Kyoto University, Kyoto (Japan); Oka, Yoshio [Department of Natural Environment Sciences, Faculty of Integrated Human Studies, Kyoto University, Kyoto (Japan)

    1997-04-16

    A comment on the article entitled `molecular dynamic simulation of the vanadium pentoxide gel host` [J. Linde and J.O. Thomas, Solid State Ionics 85 (1996) 1] is presented concerning the model structure of the V{sub 2}O{sub 5} layer of vanadium pentoxide gels. The double-layer structure used in the simulation was derived from the crystalline V{sub 2}O{sub 5}. This model structure significantly differs from the double-sheet type determined by the X-ray Rietvelt method. The simulation should be recalculated based on the double-sheet type V{sub 2}O{sub 5} layer

  16. Fluid diversion and sweep improvement with chemical gels in oil recovery processes. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Seright, R.S.; Martin, F.D.

    1992-09-01

    The objectives of this project were to identify the mechanisms by which gel treatments divert fluids in reservoirs and to establish where and how gel treatments are best applied. Several different types of gelants were examined, including polymer-based gelants, a monomer-based gelant, and a colloidal-silica gelant. This research was directed at gel applications in water injection wells, in production wells, and in high-pressure gas floods. The work examined how the flow properties of gels and gelling agents are influenced by permeability, lithology, and wettability. Other goals included determining the proper placement of gelants, the stability of in-place gels, and the types of gels required for the various oil recovery processes and for different scales of reservoir heterogeneity. During this three-year project, a number of theoretical analyses were performed to determine where gel treatments are expected to work best and where they are not expected to be effective. The most important, predictions from these analyses are presented. Undoubtedly, some of these predictions will be controversial. However, they do provide a starting point in establishing guidelines for the selection of field candidates for gel treatments. A logical next step is to seek field data that either confirm or contradict these predictions. The experimental work focused on four types of gels: (1) resorcinol-formaldehyde, (2) colloidal silica, (3) Cr{sup 3+}(chloride)-xanthan, and (4) Cr{sup 3+}(acetate)-polyacrylamide. All experiments were performed at 41{degrees}C.

  17. Modification of gel architecture and TBE/TAE buffer composition to minimize heating during agarose gel electrophoresis.

    Science.gov (United States)

    Sanderson, Brian A; Araki, Naoko; Lilley, Jennifer L; Guerrero, Gilberto; Lewis, L Kevin

    2014-06-01

    Agarose gel electrophoresis of DNA and RNA is routinely performed using buffers containing either Tris, acetate, and EDTA (TAE) or Tris, borate, and EDTA (TBE). Gels are run at a low, constant voltage (∼10 V/cm) to minimize current and asymmetric heating effects, which can induce band artifacts and poor resolution. In this study, alterations of gel structure and conductive media composition were analyzed to identify factors causing higher electrical currents during horizontal slab gel electrophoresis. Current was reduced when thinner gels and smaller chamber buffer volumes were used, but was not influenced by agarose concentration or the presence of ethidium bromide. Current was strongly dependent on the amount and type of EDTA used and on the concentrations of the major acid-base components of each buffer. Interestingly, resolution and the mobilities of circular versus linear plasmid DNAs were also affected by the chemical form and amount of EDTA. With appropriate modifications to gel structure and buffer constituents, electrophoresis could be performed at high voltages (20-25 V/cm), reducing run times by up to 3-fold. The most striking improvements were observed with small DNAs and RNAs (10-100 bp): high voltages and short run times produced sharper bands and higher resolution. Copyright © 2014 Elsevier Inc. All rights reserved.

  18. sol-gel

    African Journals Online (AJOL)

    PROJET SOJA

    avec le CdS, semi-conducteur, photoconducteur, piézoélectrique et il peut servir de guide d'onde optique. C'est un cristal à structure hexagonale de type Wurtzite appartenant à la classe 6mm. Il a un grand gap de l'ordre de 3.3 eV et se caractérise par une coefficient de transmission de 90 % environ dans le spectre visible.

  19. Polyacrylamide temperature gradient gel electrophoresis.

    Science.gov (United States)

    Viglasky, Viktor

    2013-01-01

    Temperature Gradient Gel Electrophoresis (TGGE) is a form of electrophoresis in which temperature gradient is used to denature molecules as they move through either acrylamide or agarose gel. TGGE can be applied to analyze DNA, RNA, protein-DNA complexes, and, less commonly, proteins. Separation of double-stranded DNA molecules during TGGE relies on temperature-dependent melting of the DNA duplex into two single-stranded DNA molecules. Therefore, the mobility of DNA reflects not only the size of the molecule but also its nucleotide composition, thereby allowing separation of DNA molecules of similar size with different sequences. Depending on the relative orientation of electric field and temperature gradient, TGGE can be performed in either a parallel or a perpendicular mode. The former is used to analyze multiple samples in the same gel, whereas the later allows detailed analysis of a single sample. This chapter is focused on analysis of DNA by polyacrylamide TGGE using the perpendicular mode.

  20. Sol-gel derived sorbents

    Science.gov (United States)

    Sigman, Michael E.; Dindal, Amy B.

    2003-11-11

    Described is a method for producing copolymerized sol-gel derived sorbent particles for the production of copolymerized sol-gel derived sorbent material. The method for producing copolymerized sol-gel derived sorbent particles comprises adding a basic solution to an aqueous metal alkoxide mixture for a pH.ltoreq.8 to hydrolyze the metal alkoxides. Then, allowing the mixture to react at room temperature for a precalculated period of time for the mixture to undergo an increased in viscosity to obtain a desired pore size and surface area. The copolymerized mixture is then added to an immiscible, nonpolar solvent that has been heated to a sufficient temperature wherein the copolymerized mixture forms a solid upon the addition. The solid is recovered from the mixture, and is ready for use in an active sampling trap or activated for use in a passive sampling trap.

  1. Sol-gel precursors and products thereof

    Science.gov (United States)

    Warren, Scott C.; DiSalvo, Jr., Francis J.; Weisner, Ulrich B.

    2017-02-14

    The present invention provides a generalizable single-source sol-gel precursor capable of introducing a wide range of functionalities to metal oxides such as silica. The sol-gel precursor facilitates a one-molecule, one-step approach to the synthesis of metal-silica hybrids with combinations of biological, catalytic, magnetic, and optical functionalities. The single-source precursor also provides a flexible route for simultaneously incorporating functional species of many different types. The ligands employed for functionalizing the metal oxides are derived from a library of amino acids, hydroxy acids, or peptides and a silicon alkoxide, allowing many biological functionalities to be built into silica hybrids. The ligands can coordinate with a wide range of metals via a carboxylic acid, thereby allowing direct incorporation of inorganic functionalities from across the periodic table. Using the single-source precursor a wide range of functionalized nanostructures such as monolith structures, mesostructures, multiple metal gradient mesostructures and Stober-type nanoparticles can be synthesized. ##STR00001##

  2. Screening effect on nanostructure of charged gel

    DEFF Research Database (Denmark)

    Sugiyama, M; Annaka, M; Hino, M

    2004-01-01

    Charge screening effects on nanostructures of N-isopropylacrylamide-sodium acrylate (NIPA-SA) and -acrylic acid (NIPA-AAc) gels are investigated with small-angle neutron scattering. The NIPA-SA and NIPA-AAc gels with low water content exhibit microphase separations with different dimensions....... The dehydrated NIPA-SA gel also makes the microphase separation but the dehydrated NIPA-AAc gel does not. These results indicate that ionic circumstance around charged bases strongly affects the nanostructures both of the dehydrated gel and the gel with low water content. (C) 2004 Elsevier B. V. All rights...

  3. Screening effect on nanostructure of charged gel

    International Nuclear Information System (INIS)

    Sugiyama, Masaaki; Annaka, Masahiko; Hino, Masahiro; Fukunaga, Toshiharu; Vigild, Martin E.; Hara, Kazuhiro

    2004-01-01

    Charge screening effects on nanostructures of N-isopropylacrylamide-sodium acrylate (NIPA-SA) and -acrylic acid (NIPA-AAc) gels are investigated with small-angle neutron scattering. The NIPA-SA and NIPA-AAc gels with low water content exhibit microphase separations with different dimensions. The dehydrated NIPA-SA gel also makes the microphase separation but the dehydrated NIPA-AAc gel does not. These results indicate that ionic circumstance around charged bases strongly affects the nanostructures both of the dehydrated gel and the gel with low water content

  4. Screening effect on nanostructure of charged gel

    Science.gov (United States)

    Sugiyama, Masaaki; Annaka, Masahiko; Hino, Masahiro; Fukunaga, Toshiharu; E. Vigild, Martin; Hara, Kazuhiro

    2004-07-01

    Charge screening effects on nanostructures of N-isopropylacrylamide-sodium acrylate (NIPA-SA) and -acrylic acid (NIPA-AAc) gels are investigated with small-angle neutron scattering. The NIPA-SA and NIPA-AAc gels with low water content exhibit microphase separations with different dimensions. The dehydrated NIPA-SA gel also makes the microphase separation but the dehydrated NIPA-AAc gel does not. These results indicate that ionic circumstance around charged bases strongly affects the nanostructures both of the dehydrated gel and the gel with low water content.

  5. Development of sol-gel formulations for slow release of phermones

    Science.gov (United States)

    A new type of dispenser for slow-release of semiochemicals and sex pheromones was developed based on sol-gel polymers that can be useful in monitoring, mass trapping, and mating disruption in integrated pest management (IPM). Sol-gel matrices exhibit glass characteristics and allow control of the de...

  6. Structurally stable gel bead containing entrapped enzyme and method for manufacture thereof

    Science.gov (United States)

    Woodward, J.

    1998-12-08

    This research provides a structurally stable gel bead containing an entrapped enzyme and a method for its manufacture. The enzyme is covalently cross-linked to gelatin in the presence of glutaraldehyde prior to the formation of the gel bead, to prevent leakage of the enzyme. Propylene glycol alginate is then added to the mixture. Once the gel beads are formed, they are then soaked in glutaraldehyde, which imparts structural stability to the gel beads. This method can be used with many types of enzymes, such as proteases, carbohydrases, proteases, ligases, isomerases, oxidoreductases, and specialty enzymes. These and other enzymes can be immobilized in the gel beads and utilized in a number of enzymatic processes. Exogenously added ions are not required to maintain the structural stability of these gel beads. 7 figs.

  7. SAXS EXPERIMENTS ON GEL-SPUN POLYETHYLENE FIBERS

    NARCIS (Netherlands)

    Hoogsteen, W.; Pennings, A.J.; Brinke, G. ten

    The properties of gel-spun polyethylene fibers hot-drawn to the maximum draw ratio depend on the spinning conditions. Different spinning conditions result in two types of structure in the paraffin oil containing fibers: an isotropic lamellar structure or a shish-kebab structure. Meridional SAXS

  8. The Bioadhesive and Rheological properties of some fluconazole gels

    African Journals Online (AJOL)

    The results obtained indicate that high viscosity grade sodium carboxymethylcellulose (HV NaCMC) at 1.0 - 2% w/w concentration levels gave bioadhesive gels with viscoelastic properties which are affected by type and concentration of dye added to the formulation either as excipient or to assist in the determination of MTR.

  9. Nonlinear elasticity of alginate gels

    Science.gov (United States)

    Hashemnejad, Seyed Meysam; Kundu, Santanu

    Alginate is a naturally occurring anionic polysaccharide extracted from brown algae. Because of biocompatibility, low toxicity, and simple gelation process, alginate gels are used in biomedical and food applications. Here, we report the rheological behavior of ionically crosslinked alginate gels, which are obtained by in situ gelation of alginates with calcium salts, in between two parallel plates of a rheometer. Strain stiffening behavior was captured using large amplitude oscillatory shear (LAOS) experiments. In addition, negative normal stress was observed for these gels, which has not been reported earlier for any polysaccharide networks. The magnitude of negative normal stress increases with applied strain and can exceed that of the shear stress at large strain. Rheological results fitted with a constitutive model that considers both stretching and bending of chains indicate that nonlinearity is likely related to the stretching of the chains between the crosslink junctions. The results provide an improved understanding of the deformation mechanism of ionically crosslinked alginate gel and the results will be important in developing synthetic extracellular matrix (ECM) from these materials.

  10. Scaffold architecture and fibrin gels promote meniscal cell proliferation

    Energy Technology Data Exchange (ETDEWEB)

    Pawelec, K. M., E-mail: pawelec.km@gmail.com, E-mail: jw626@cam.ac.uk; Best, S. M.; Cameron, R. E. [Cambridge Centre for Medical Materials, Materials Science and Metallurgy Department, University of Cambridge, Cambridge CB3 0FS (United Kingdom); Wardale, R. J., E-mail: pawelec.km@gmail.com, E-mail: jw626@cam.ac.uk [Division of Trauma and Orthopaedic Surgery, Department of Surgery, University of Cambridge, Cambridge CB2 2QQ (United Kingdom)

    2015-01-01

    Stability of the knee relies on the meniscus, a complex connective tissue with poor healing ability. Current meniscal tissue engineering is inadequate, as the signals for increasing meniscal cell proliferation have not been established. In this study, collagen scaffold structure, isotropic or aligned, and fibrin gel addition were tested. Metabolic activity was promoted by fibrin addition. Cellular proliferation, however, was significantly increased by both aligned architectures and fibrin addition. None of the constructs impaired collagen type I production or triggered adverse inflammatory responses. It was demonstrated that both fibrin gel addition and optimized scaffold architecture effectively promote meniscal cell proliferation.

  11. Silicone Gel-Filled Breast Implants

    Science.gov (United States)

    ... and Prosthetics Breast Implants Silicone Gel-Filled Breast Implants Share Tweet Linkedin Pin it More sharing options ... it Email Print Description: Silicone gel-filled breast implants have a silicone outer shell that is filled ...

  12. Dosimetry for computed tomography using Fricke gel dosimetry and magnetic resonance imaging; Dosimetria em tomografia computadorizada empregando dosimetro Fricke gel e a tecnica de imageamento por ressonancia magnetica

    Energy Technology Data Exchange (ETDEWEB)

    Capeleti, Felipe Favaro; Campos, Leticia L., E-mail: felipe@gmpbrasil.com.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2014-04-15

    In this work it was determined a new method for the determination of absorbed doses in Computed Tomography (CT) examinations using Fricke gel dosimetry developed at IPEN. Absorbed doses were determined by different methods of analysis, such as optical absorption spectrometry, ionization chambers and magnetic resonance imaging. Lower limit of sensitivity of the Fricke gel solution, the solution repeatability signal Fricke gel and CT equipment, detection sensitivity, among other tests were performed. Different equipment of computed tomography with multiple detectors were used. The Fricke gel solution showed better repeatability than ±5.5% using the technique of optical absorption spectrophotometry and computed tomography equipment showed repeatability better than ±0.2%. The Fricke gel solution features an easy and relatively quick preparation, but it is necessary to be careful not to contaminate and lose the solution. With the results, it was confirmed the application of this type of dosimetry for computed tomography equipment. (author)

  13. Surface grafted chitosan gels. Part II. Gel formation and characterization

    DEFF Research Database (Denmark)

    Liu, Chao; Thormann, Esben; Claesson, Per M.

    2014-01-01

    Responsive biomaterial hydrogels attract significant attention due to their biocompatibility and degradability. In order to make chitosan based gels, we first graft one layer of chitosan to silica, and then build a chitosan/poly(acrylic acid) multilayer using the layer-by-layer approach. After...... detachment and decomposition. The chemical reaction between gluteraldehyde, the cross-linking agent, and chitosan was followed in situ using total internal reflection Raman (TIRR) spectroscopy, which provided a molecular insight into the complex reaction mechanism, as well as the means to quantify the cross......-linking density. The amount of poly(acrylic acid) trapped inside the surface grafted films was found to decrease with decreasing cross-linking density, as confirmed in situ using TIRR, and ex situ by Fourier transform infrared (FTIR) measurements on dried films. The responsiveness of the chitosan-based gels...

  14. Detection of ultraviolet radiation using tissue equivalent radiochromic gel materials

    International Nuclear Information System (INIS)

    Bero, M A; Abukassem, I

    2009-01-01

    Ferrous Xylenol-orange Gelatin gel (FXG) is known to be sensitive to ionising radiation such as γ and X-rays. The effect of ionising radiation is to produce an increase in the absorption over a wide region of the visible spectrum, which is proportional to the absorbed dose. This study demonstrates that FXG gel is sensitive to ultraviolet radiation and therefore it could functions as UV detector. Short exposure to UV radiation produces linear increase in absorption measured at 550nm, however high doses of UV cause the ion indicator colour to fad away in a manner proportional to the incident UV energy. Light absorbance increase at the rate of 1.1% per minute of irradiation was monitored. The exposure level at which the detector has linear response is comparable to the natural summer UV radiation. Evaluating the UV ability to pass through tissue equivalent gel materials shows that most of the UV gets absorbed in the first 5mm of the gel materials, which demonstrate the damaging effects of this radiation type on human skin and eyes. It was concluded that FXG gel dosimeter has the potential to offer a simple, passive ultraviolet radiation detector with sensitivity suitable to measure and visualises the natural sunlight UV exposure directly by watching the materials colour changes.

  15. Effects of fibre dimension and charge density on nanocellulose gels.

    Science.gov (United States)

    Mendoza, Llyza; Gunawardhana, Thilina; Batchelor, Warren; Garnier, Gil

    2018-04-18

    Carboxylated cellulose nanofibres can produce gels at low concentrations. The effect of pulp source on the nanocellulose fibre dimension and gel rheology are studied. It is hypothesised that fibre length and surface charge influence aspects of the gel rheological properties. TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl)- mediated oxidised cellulose nanofibres from never-dried hardwood and softwood pulp and containing different charge levels were produced and characterized. Steady-state and dynamic rheological studies were performed to ascertain the effects of pulp type on gel behavior and properties. Nanocellulose fibres extracted from softwood (SW-TOCN) and hardwood (HW-TOCN) pulp exhibit similar widths but different length dimensions as shown via AFM analysis. Rheological measurements show that the dynamic moduli (G' and G'') of nanocellulose gels are independent of pulp source and are mostly influenced by fibre concentration. Differences in the steady-state behavior (i.e. viscosity) at constant surface charge can be attributed to differences in fibre length. Increasing the surface charge density influences the critical strain and the viscosity at the percolation concentration (0.1 wt%) due to higher electrostatic interactions. Crown Copyright © 2018. Published by Elsevier Inc. All rights reserved.

  16. Self-Supporting Nanodiamond Gels: Elucidating Colloidal Interactions Through Rheology_

    Science.gov (United States)

    Adhikari, Prajesh; Tripathi, Anurodh; Vogel, Nancy A.; Rojas, Orlando J.; Raghavan, Sriunivasa R.; Khan, Saad A.

    This work investigates the colloidal interactions and rheological behavior of nanodiamond (ND) dispersions. While ND represents a promising class of nanofiller due to its high surface area, superior mechanical strength, tailorable surface functionality and biocompatibility, much remains unknown about the behavior of ND dispersions. We hypothesize that controlling interactions in ND dispersions will lead to highly functional systems with tunable modulus and shear response. Steady and dynamic rheology techniques are thus employed to systematically investigate nanodiamonds dispersed in model polar and non-polar media. We find that low concentrations of ND form gels almost instantaneously in a non-polar media. In contrast, ND's in polar media show a time-dependent behavior with the modulus increasing with time. We attribute the difference in behavior to variations in inter-particle interactions as well as the interaction of the ND with the media. Large steady and oscillatory strains are applied to ND colloidal gels to investigate the role of shear in gel microstructure breakdown and recovery. For colloidal gels in non-polar medium, the incomplete recovery of elastic modulus at high strain amplitudes indicates dominance of particle-particle interactions; however, in polar media the complete recovery of elastic modulus even at high strain amplitudes indicates dominance of particle-solvent interactions. These results taken together provide a platform to develop self-supporting gels with tunable properties in terms of ND concentration, and solvent type.

  17. Comparison of typing by whole genome sequencing (WGS) and pulsed field gel electrophoresis (PFGE) of isolates from a hospital outbreak with a CTX-M-15 producing Klebsiella pneumoniae

    DEFF Research Database (Denmark)

    Hansen, D. S.; Kaas, Rolf Sommer; Nielsen, E. M.

    2013-01-01

    Objective: Klebsiella pneumoniae (KP) is the archetype of a Gram negative outbreak organism with acquired antibiotic resistance. Reference epidemiology typing method have for many years been PFGE. The ultimate typing tool must however be knowing the entire variation within the genomes...... of the involved organisms. Recent technological development and pricing have made this possible. Our objective was to compare typing by WGS with PFGE on nosocomial KP outbreak isolates. Methods: 44 KP isolates from 2006 (pre-outbreak) through 2007/8 (outbreak) to 2011 (endemic) from 33 patients and 5 KP reference....... WGS has higher resolution and are able to discriminate between isolates of same PFGE type....

  18. Physical Properties of Silicone Gel Breast Implants.

    Science.gov (United States)

    Jewell, Mark L; Bengtson, Bradley P; Smither, Kate; Nuti, Gina; Perry, TracyAnn

    2018-04-28

    Surgical applications using breast implants are individualized operations to fill and shape the breast. Physical properties beyond shape, size, and surface texture are important considerations during implant selection. Compare form stability, gel material properties, and shell thickness of textured shaped, textured round, and smooth round breast implants from 4 manufacturers: Allergan, Mentor, Sientra, and Establishment Labs through bench testing. Using a mandrel height gauge, form stability was measured by retention of dimensions on device movement from a horizontal to vertical supported orientation. Dynamic response of gel material (gel cohesivity, resistance to gel deformation, energy absorption) was measured using a synchronized target laser following application of graded negative pressure. Shell thickness was measured using digital thickness gauge calipers. Form stability, gel material properties, and shell thickness differed across breast implants. Of textured shaped devices, Allergan Natrelle 410 exhibited greater form stability than Mentor MemoryShape and Sientra Shaped implants. Allergan Inspira round implants containing TruForm 3 gel had greater form stability, higher gel cohesivity, greater resistance to gel deformation, and lower energy absorption than those containing TruForm 2 gel and in turn, implants containing TruForm 1 gel. Shell thickness was greater for textured versus smooth devices, and differed across styles. Gel cohesivity, resistance to gel deformation, and energy absorption are directly related to form stability, which in turn determines shape retention. These characteristics provide information to aid surgeons choosing an implant based on surgical application, patient tissue characteristics, and desired outcome.

  19. Supramolecular gel electrophoresis of large DNA fragments.

    Science.gov (United States)

    Tazawa, Shohei; Kobayashi, Kazuhiro; Oyoshi, Takanori; Yamanaka, Masamichi

    2017-10-01

    Pulsed-field gel electrophoresis is a frequent technique used to separate exceptionally large DNA fragments. In a typical continuous field electrophoresis, it is challenging to separate DNA fragments larger than 20 kbp because they migrate at a comparable rate. To overcome this challenge, it is necessary to develop a novel matrix for the electrophoresis. Here, we describe the electrophoresis of large DNA fragments up to 166 kbp using a supramolecular gel matrix and a typical continuous field electrophoresis system. C 3 -symmetric tris-urea self-assembled into a supramolecular hydrogel in tris-boric acid-EDTA buffer, a typical buffer for DNA electrophoresis, and the supramolecular hydrogel was used as a matrix for electrophoresis to separate large DNA fragments. Three types of DNA marker, the λ-Hind III digest (2 to 23 kbp), Lambda DNA-Mono Cut Mix (10 to 49 kbp), and Marker 7 GT (10 to 165 kbp), were analyzed in this study. Large DNA fragments of greater than 100 kbp showed distinct mobility using a typical continuous field electrophoresis system. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Cumulative irritation potential among metronidazole gel 1%, metronidazole gel 0.75%, and azelaic acid gel 15%.

    Science.gov (United States)

    Colón, Luz E; Johnson, Lori A; Gottschalk, Ronald W

    2007-04-01

    Topical therapy for rosacea aims to reduce inflammatory lesions and decrease erythema but can carry side effects such as stinging, pruritus, and burning. Metronidazole and azelaic acid gel 15% are U.S. Food and Drug Administration-approved for the treatment of rosacea. The current study was conducted to assess the cumulative irritation potential of 2 formulations of metronidazole 0.75% gel and 1% gel--and azelaic acid gel 15% over 21 days (N=36). Results of this study demonstrated a significantly greater poten tial for irritation from azelaic acid compared with metronidazole gel 0.75% (P < .0001), which had significantly greater potential for irritation compared with metronidazole gel 1% (P = .0054). Metronidazole gel 1% had a similar profile to white petrolatum.

  1. Nanocrystal/sol-gel nanocomposites

    Science.gov (United States)

    Klimov, Victor L.; Petruska, Melissa A.

    2010-05-25

    The present invention is directed to a process for preparing a solid composite having colloidal nanocrystals dispersed within a sol-gel matrix, the process including admixing colloidal nanocrystals with an amphiphilic polymer including hydrophilic groups selected from the group consisting of --COOH, --OH, --SO.sub.3H, --NH.sub.2, and --PO.sub.3H.sub.2 within a solvent to form an alcohol-soluble colloidal nanocrystal-polymer complex, admixing the alcohol-soluble colloidal nanocrystal-polymer complex and a sol-gel precursor material, and, forming the solid composite from the admixture. The present invention is also directed to the resultant solid composites and to the alcohol-soluble colloidal nanocrystal-polymer complexes.

  2. User-identified gel characteristics: a qualitative exploration of perceived product efficacy of topical vaginal microbicides.

    Science.gov (United States)

    Morrow, Kathleen M; Underhill, Kristen; van den Berg, Jacob J; Vargas, Sara; Rosen, Rochelle K; Katz, David F

    2014-10-01

    Research has demonstrated that certain vaginal gel products--microbicides containing antiretroviral drugs--may reduce HIV infection risk among women. But for vaginal gels to avert HIV and other sexually transmitted infections (STIs), at-risk women must be willing to use them as directed. These products must therefore be "acceptable" to women and an important component of acceptability is users' perception that the product will work to prevent infection. We sought to understand how women's perceptions of vaginal gel properties may shape their understanding of product efficacy for HIV and STI prevention. Sixteen women completed two in-depth qualitative interviews (k = 32) to identify the range and types of sensory perceptions they experienced when using two vaginal gels. We identified emergent themes and linkages between users' sensory perceptions and their beliefs about product efficacy. Users' predictions about product efficacy for preventing infection corresponded to measurable physical properties, including gel volume, location in the vagina, coating behavior, sensation of the gel in the vagina, leakage, and gel changes during coital acts. Although the women described similar sensory experiences (e.g., gel leaked from the vagina), they interpreted these experiences to have varying implications for product efficacy (e.g., leakage was predicted to increase or decrease efficacy). To improve microbicide acceptability, gel developers should investigate and deliberately incorporate properties that influence users' perceptions of efficacy. When a microbicide is approved for use, providers should educate users to anticipate and understand their sensory experiences; improving users' experience can maximize adherence and product effectiveness.

  3. Using stability analyses to predict dynamic behaviour of self-oscillating polymer gels

    Science.gov (United States)

    Palkar, Vaibhav; Srivastava, Gaurav; Kuksenok, Olga; Balazs, Anna C.; Dayal, Pratyush

    2015-03-01

    Use of chemo-mechanical transduction to produce locomotion is one of the significant characteristics of biological systems. Polymer gels, intrinsically powered by oscillatory Belousov-Zhabotinsky (BZ) reaction, are biomimetic materials that exhibit rhythmic self-sustained mechanical oscillations by chemo-mechanical transduction. Via simulations, based on the 3D gel lattice spring model, we have successfully captured the dynamic behaviour of BZ gels. We have demonstrated that it is possible to direct the movement of BZ gels along complex paths, guiding them to bend, reorient and turn. From a mathematical perspective, the oscillations in the BZ gels occur when the gel's steady states loose stability by virtue of Hopf bifurcations (HB). Through the use of stability analyses, we predict the conditions under which gel switches from stationary to oscillatory mode and vice versa. In addition, we characterize the nature of HB and also identify other types of bifurcations that play a critical role in governing the dynamic behaviour of BZ gels. Also, we successfully predict the frequency of chemo-mechanical oscillations and characterize its dependency on the model parameters. Our approach not only allows us to establish optimal conditions for the motion of BZ gels, but also can be used to design other dynamical systems. IIT Gandhinagar and DST-SERB for funding.

  4. Passivated gel electrophoresis of charged nanospheres by light-scattering video tracking.

    Science.gov (United States)

    Zhu, Xiaoming; Mason, Thomas G

    2014-08-15

    Gel electrophoresis (gel-EP) has been used for decades to separate charged biopolymers, such as DNA, RNA, and proteins, yet propagation of other charged colloidal objects, such as nanoparticles, during gel-EP has been studied comparatively little. Simply introducing anionic nanoparticles, such as sulfate-stabilized polystyrene nanospheres, in standard large-pore agarose gels commonly used for biomolecules does not automatically ensure propagation or size-separation because attractive interactions can exist between the gel and the nanoparticles. Whereas altering the surfaces of the nanoparticles is a possible solution, here, by contrast, we show that treating a common type I-A low-electroendoosmosis agarose gel with a passivation agent, such as poly-(ethyleneglycol), enables charged nanoparticles to propagate through large-pore passivated gels in a highly reproducible manner. Moreover, by taking advantage of the significant optical scattering from the nanoparticles, which is not easily measurable for biopolymers, relative to scattering from the gel, we perform real-time, light-scattering, video-tracking gel-EP. Continuous optical measurements of the propagation of bands of uniformly sized nanospheres in passivated gels provides the propagation distance, L, and velocity, v, as a function of time for different sphere radii, electric field strengths, gel concentrations, and passivation agent concentrations. The steady-state particle velocities vary linearly with applied electric field strength, E, for small E, but these velocities become non-linear for larger E, suggesting that strongly driven nanoparticles can become elastically trapped in the smaller pores of the gel, which act like blind holes, in a manner that thermal fluctuations cannot overcome. Based on this assumption, we introduce a simple model that fits the measured v(E) in both linear and non-linear regimes over a relevant range of applied voltages. Copyright © 2014 Elsevier Inc. All rights reserved.

  5. Microphase separation in nanocomposite gels

    Science.gov (United States)

    Osaka, Noboru; Endo, Hitoshi; Nishida, Toshihiko; Suzuki, Takuya; Li, Huan-Jun; Haraguchi, Kazutoshi; Shibayama, Mitsuhiro

    2009-06-01

    Microphase separation in poly( N -isopropylacrylamide)(PNIPA)-clay nanocomposite hydrogels (NC gels) is investigated by means of contrast-variation small-angle neutron scattering (CV-SANS) and dynamic light scattering (DLS). By using CV-SANS, it is revealed that microphase separation occurs in NC gels above the lower-critical solution temperature (LCST) of PNIPA aqueous solutions. The observed partial scattering functions show that only the spatial distribution of PNIPA chains is highly distorted by microphase separation and PNIPA chains are preferentially adsorbed on the clay surfaces, where the PNIPA-rich phase forms nanoscaled bicontinuous structure mediated by the clay particles. Additional DLS measurements for dilute solutions with PNIPA and/or the clay nanoparticles confirm that aggregation of PNIPA above the LCST is dramatically suppressed by addition of clay particles. Based on these observations, we conclude that strong affinity between the polymer and clay has a significant effect on the phase separation in NC gels and allows one to tune the length scale of the phase separation phenomenon by clay concentration.

  6. Accessing alkali-free NASICON-type compounds through mixed oxoanion sol–gel chemistry: Hydrogen titanium phosphate sulfate, H{sub 1−x}Ti{sub 2}(PO{sub 4}){sub 3−x}(SO{sub 4}){sub x} (x=0.5–1)

    Energy Technology Data Exchange (ETDEWEB)

    Mieritz, Daniel; Davidowski, Stephen K.; Seo, Dong-Kyun, E-mail: dseo@asu.edu

    2016-10-15

    We report a direct sol–gel synthesis and characterization of new proton-containing, rhombohedral NASICION-type titanium compounds with mixed phosphate and sulfate oxoanions. The synthetic conditions were established by utilizing peroxide ion as a decomposable and stabilizing ligand for titanyl ions in the presence of phosphates in a strong acidic medium. Thermogravimetric analysis (TGA), powder X-ray diffraction (PXRD), induction-coupled plasma optical emission spectroscopic (ICP-OES) elemental analysis, and Raman and {sup 1}H magic angle spinning nuclear magnetic resonance (MAS-NMR) spectroscopic studies have determined the presence of sulfate and proton ions in the structure, for which the compositional range has been found to be H{sub 1−x}Ti{sub 2}(PO{sub 4}){sub 3−x}(SO{sub 4}){sub x} (x=0.5–1). The particulate products exhibit a nanocrystalline nature observed through characterization with scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The N{sub 2} sorption isotherm measurements and subsequent Brunauer–Emmett–Teller (BET) and Barrett–Joyner–Halenda (BJH) analyses confirmed the presence of the textural meso- and macropores in the materials. Future studies would determine the potential of the new compounds in various applications as battery materials, proton conductors and solid acid catalysts. - Graphical abstract: A series of proton-containing NASICON-type compounds, H{sub 1−x}Ti{sub 2}(PO{sub 4}){sub 3−x}(SO{sub 4}){sub x} (x=0.5–1), were discovered through a new sol–gel synthetic method that utilizes peroxide ion as a decomposable and stabilizing ligand for titanyl ions in the presence of phosphates in a strong acidic medium.

  7. The Gelså River Restoration Revisited

    DEFF Research Database (Denmark)

    Friberg, Nikolai; Baattrup-Pedersen, Annette; Kristensen, Esben

    2014-01-01

    The study was undertaken on the River Gelså, Denmark, where a 1.8 km meandering course was estab-lished in 1989 to replace a channelized river reach. This restoration project was the first of its kind inDenmark and has the longest time-series of post-intervention data of any restoration project...... to saturationin 1997 and that only limited immigration of new species occurred in the intervening period until 2008.The lack of long term benefits could be attributed to the simultaneous cessation of weed cutting (whichhad almost as big a positive impact as restoration), other types of stress on the river...... conductedworld-wide. Additionally, a 0.5 km upstream (control) reach that remained channelized has been sampledsince 1989. In this paper, we examined macroinvertebrate assemblages in distinct habitats in 2008, 19years after the restoration, and community persistence between two years, 1997 and 2008...

  8. Bucky gel actuator displacement: experiment and model

    International Nuclear Information System (INIS)

    Ghamsari, A K; Zegeye, E; Woldesenbet, E; Jin, Y

    2013-01-01

    Bucky gel actuator (BGA) is a dry electroactive nanocomposite which is driven with a few volts. BGA’s remarkable features make this tri-layered actuator a potential candidate for morphing applications. However, most of these applications would require a better understanding of the effective parameters that influence the BGA displacement. In this study, various sets of experiments were designed to investigate the effect of several parameters on the maximum lateral displacement of BGA. Two input parameters, voltage and frequency, and three material/design parameters, carbon nanotube type, thickness, and weight fraction of constituents were selected. A new thickness ratio term was also introduced to study the role of individual layers on BGA displacement. A model was established to predict BGA maximum displacement based on the effect of these parameters. This model showed good agreement with reported results from the literature. In addition, an important factor in the design of BGA-based devices, lifetime, was investigated. (paper)

  9. Aspects of dosimetry using radiation sensitive gels

    International Nuclear Information System (INIS)

    Baldock, Clive

    2001-01-01

    The use of radiation sensitive gels for dosimetry measurements was first suggested in the 1950s. It was subsequently shown that radiation induced changes in nuclear magnetic resonance (NMR) relaxation properties of gels infused with conventional Fricke dosimetry solutions could be measured. However, due to predominantly diffusion-related limitations, alternative polymer gel dosimeters were suggested. Clinical applications of these radiologically tissue equivalent gel dosimeters using magnetic resonance imaging (MRI) have subsequently been reported in the literature. In Fricke gels, Fe 2+ ions in ferrous sulphate solutions are usually dispersed throughout a gelatin or agarose hydrogel matrix. Radiation-induced changes in the dosimeters are considered to be either through direct absorption of ionising radiation or via intermediate water free radicals. Fe 2+ ions are converted to Fe 3+ ions with a corresponding change in paramagnetic properties that may be quantified using NMR relaxation measurements. In polymer gels, monomers are also dispersed in a gelatin or agarose hydrogel matrix. Monomers undergo a polymerisation reaction as a function of absorbed dose resulting in a three-dimensional polymer gel matrix. The radiation-induced formation of polymer influences NMR relaxation properties. The growth in polymer also results in other physical changes that may be used to quantify absorbed radiation dose. This thesis investigates various aspects of radiation dosimetry using radiation sensitive gels. Image processing software was developed to calculate NMR relaxation images of dosimetry gels. Measurements were undertaken to investigate the diffusion problem in Fricke gels. Radiological properties were theoretically modelled for both Fricke and polymer gels. A methodology was developed for the preparation of polymer gels. Vibrational spectroscopic studies were undertaken to investigate the underlying mechanism involved in the radiation-induced formation of polymer. MRI

  10. Development of Smart Optical Gels with Highly Magnetically Responsive Bicelles.

    Science.gov (United States)

    Isabettini, Stéphane; Stucki, Sandro; Massabni, Sarah; Baumgartner, Mirjam E; Reckey, Pernille Q; Kohlbrecher, Joachim; Ishikawa, Takashi; Windhab, Erich J; Fischer, Peter; Kuster, Simon

    2018-03-14

    Hydrogels delivering on-demand tailorable optical properties are formidable smart materials with promising perspectives in numerous fields, including the development of modern sensors and switches, the essential quality criterion being a defined and readily measured response to environmental changes. Lanthanide ion (Ln 3+ )-chelating bicelles are interesting building blocks for such materials because of their magnetic responsive nature. Imbedding these phospholipid-based nanodiscs in a magnetically aligned state in gelatin permits an orientation-dependent retardation of polarized light. The resulting tailorable anisotropy gives the gel a well-defined optical signature observed as a birefringence signal. These phenomena were only reported for a single bicelle-gelatin pair and required high magnetic field strengths of 8 T. Herein, we demonstrate the versatility and enhance the viability of this technology with a new generation of aminocholesterol (Chol-NH 2 )-doped bicelles imbedded in two different types of gelatin. The highly magnetically responsive nature of the bicelles allowed to gel the anisotropy at commercially viable magnetic field strengths between 1 and 3 T. Thermoreversible gels with a unique optical signature were generated by exposing the system to various temperature conditions and external magnetic field strengths. The resulting optical properties were a signature of the gel's environmental history, effectively acting as a sensor. Solutions containing the bicelles simultaneously aligning parallel and perpendicular to the magnetic field directions were obtained by mixing samples chelating Tm 3+ and Dy 3+ . These systems were successfully gelled, providing a material with two distinct temperature-dependent optical characteristics. The high degree of tunability in the magnetic response of the bicelles enables encryption of the gel's optical properties. The proposed gels are viable candidates for temperature tracking of sensitive goods and provide

  11. Rheological characterization of Poloxamer 407 nimesulide gels

    Directory of Open Access Journals (Sweden)

    M. N. Freitas

    2009-01-01

    Full Text Available The thermal gelling property of Poloxamer 407- nimesulide gels was characterized by rheological studies. Nimesulide, a local anti-inflammatory and anesthetic drug used for the treatment of acute and chronic pain, has a short duration of action and a long-acting single-dose injection would be of clinical importance. Thus a poloxamer 407 gel applied intramuscularly could prolong the release and action of nimesulide. In this study, aqueous gels with nimesulide, containing three different concentrations of Poloxamer 407, were prepared. Viscosity measurements were performed by rheologial studies to obtain the optimal sol-gel transition temperature . Poloxamer 407 gels are pseudoplastic and viscoelastic materials, which have an elastic modulus (G', characteristic of the solid, and a viscous modulus (G'', characteristic of the liquid material. Moreover, being pseudoplastic gels, when they are deformed by shearing, their viscosity decreases. Increase of the polymer concentration increased the viscosity of the gels, which could affect the releasing process of nimesulide. Furthermore, the presence of nimesulide led to a lowering of the sol-gel transition temperature. Keywords: Poloxamer 407 gels; nimesulide; rheological characterization; viscosity; sol-gel transition temperature.

  12. Variability in the properties of silicone gel breast implants.

    Science.gov (United States)

    Brandon, H J; Young, V L; Jerina, K L; Wolf, C J

    2001-09-01

    Several generations of silicone gel breast implants have been produced by implant manufacturers. The primary material usually viewed as the base material in the manufacture of implants is polydimethylsiloxane. Polymeric reactions are notorious for their variability and nonuniformity. The elastomer used in different types of implants can have vastly different properties. Furthermore, the material properties associated with a particular type of implant can vary considerably from one lot to the next. Considering the various designs, styles, and manufacturing techniques associated with silicone gel implants, knowledge of the original properties of the implants before implantation is important in determining the effects of aging in vivo. This study was conducted to investigate differences in key mechanical and chemical properties of silicone gel breast implant materials. The two types of implants chosen for analysis were Silastic I and Silastic II control implants. Material property data were determined for both types of controls and significant differences were found in their values. Lot-to-lot variability was also investigated and found to be significant.

  13. Calcium Impact on Milk Gels Formation

    DEFF Research Database (Denmark)

    Koutina, Glykeria

    salts. The perturbation of calcium equilibria by these factors will affect the final properties of acid, calcium and rennet milk gels. By decreasing the pH from 6.0 to 5.2 (acid gels), the calcium equilibrium was significantly affected by temperature (4, 20, 30, 40 oC), and different combinations...... enriched dairy products. Calcium gels can be produced by addition of a calcium salt and heat treatment at temperatures higher than 70 oC for several minutes. The combination of heat treatment and calcium addition to milk with pH values between 6.6 and 5.6, will produce calcium milk gels with unique...... to be formed. In addition the low amount of micellar calcium caused a more compact gel structure with many protein aggregates. The results of this study highlighted the importance of calcium for the formation of acid, calcium and rennet gels. The content and the interactions of calcium with proteins during...

  14. Tunable Gas Sensing Gels by Cooperative Assembly.

    Science.gov (United States)

    Hussain, Abid; Semeano, Ana T S; Palma, Susana I C J; Pina, Ana S; Almeida, José; Medrado, Bárbara F; Pádua, Ana C C S; Carvalho, Ana L; Dionísio, Madalena; Li, Rosamaria W C; Gamboa, Hugo; Ulijn, Rein V; Gruber, Jonas; Roque, Ana C A

    2017-07-19

    The cooperative assembly of biopolymers and small molecules can yield functional materials with precisely tunable properties. Here, the fabrication, characterization, and use of multicomponent hybrid gels as selective gas sensors are reported. The gels are composed of liquid crystal droplets self-assembled in the presence of ionic liquids, which further coassemble with biopolymers to form stable matrices. Each individual component can be varied and acts cooperatively to tune gels' structure and function. The unique molecular environment in hybrid gels is explored for supramolecular recognition of volatile compounds. Gels with distinct compositions are used as optical and electrical gas sensors, yielding a combinatorial response conceptually mimicking olfactory biological systems, and tested to distinguish volatile organic compounds and to quantify ethanol in automotive fuel. The gel response is rapid, reversible, and reproducible. These robust, versatile, modular, pliant electro-optical soft materials possess new possibilities in sensing triggered by chemical and physical stimuli.

  15. Research on pre-staining gel electrophoresis

    International Nuclear Information System (INIS)

    Zhong Ruibo; Liu Yushuang; Zhang Ping; Liu Jingran; Zhao Guofen; Zhang Feng

    2014-01-01

    Background: Gel electrophoresis is a powerful biochemical separation technique. Most biological molecules are completely transparent in the visible region of light, so it is necessary to use staining to show the results after gel electrophoresis, and the general steps of conventional staining methods are time-consuming. Purpose: We try to develop a novel approach to simplify the gel electrophoresis: Pre-Staining Gel Electrophoresis (PSGE), which can make the gel electrophoresis results monitored in real time. Methods: Pre-stain the protein samples with Coomassie Brilliant Blue (CBB) for 30 min before loading the sample into the gel well. Results and Conclusion: PSGE can be successfully used to analyze the binding efficiency of Bovine Serum Albumin (BSA) and amphiphilic polymer via chemical coupling and physical absorption, and the double PSGE also shows a great potential in bio-analytical chemistry. (authors)

  16. Self-Pumping Active Gel

    Science.gov (United States)

    Wu, Kun-Ta; Hishamunda, Jean Bernard; Fraden, Seth; Dogic, Zvonimir

    Isotropic active gels are the network which is consist of cross-linked building blocks and the structure of which changes randomly and isotropically with time. Dogic et. al. show that pairs of anti-parallel microtubules form extensile bundles, which merge, extend, and buckle. In an unconfined system, the dynamics of these bundles causes spontaneous turbulent-like flow driven by motion of microscopic molecular motors. We found that confining these active gels in a millimeter sized toroids causes a transition into a new dynamical state characterized by circulation currents persisting for hours until ATP is depleted. We show how toroid dimensions impact the properties of self-organized circular currents, how directions of circulation can be designed by engineering ratchet-shaped boundaries, and how circulations of connected toroids can be either synchronized or antisynchronized. Furthermore, we demonstrate that the flow rate in the circulation is independent of curvature and length of flow path. The flow rate persists for centimeters without decay, disregarding conventional pipe flow resistance. Such findings pave the path to self-pumping pipe transport and performing physical work with biological system.

  17. Microfluidics of soft granular gels

    Science.gov (United States)

    Nixon, Ryan; Bhattacharjee, Tapomoy; Sawyer, W. Gregory; Angelini, Thomas E.

    Microfluidic methods for encapsulating cells and particles typically involve drop making with two immiscible fluids. The main materials constraint in this approach is surface tension, creating inherent instability between the two fluids. We can eliminate this instability by using miscible inner and outer phases. This is achieved by using granular micro gels which are chemically miscible but physically do not mix. These microgels are yield stress materials, so they flow as solid plugs far from shear gradients, and fluidize where gradients are generated - near an injection nozzle for example. We have found that tuning the yield stress of the material by varying polymer concentration, device performance can be controlled. The solid like behavior of the gel allows us to produces infinitely stable jets that maintain their integrity and configuration over long distances and times. These properties can be combined and manipulated to produce discrete particulate bunches of an inner phase, flowing inside of an outer phase, well enough even to print a Morse code message suspended within flow chambers about a millimeter in diameter moving at millimeters a second.

  18. Analysis of PEG oligomers in black gel inks: Discrimination and ink dating.

    Science.gov (United States)

    Sun, Qiran; Luo, Yiwen; Xiang, Ping; Yang, Xu; Shen, Min

    2017-08-01

    Carbon-based black gel inks are common samples in forensic practice of questioned document examination in China, but there are few analytical methods for this type of ink. In this study, a liquid chromatography-.high resolution mass spectrometry (LC-HRMS) method was established for the analysis of PEG oligomers in carbon-based black gel ink entries. The coupled instruments achieve both the identification and quantification of PEG oligomers in ink entries with reproducible results. Twenty carbon-based black gel inks, whose Raman spectra appeared identical, were analyzed using the LC-HRMS method. As a result, the twenty gel inks were classified into four groups according to the distribution of PEG oligomers. Artificially aging of PEG 400 and a gel ink showed that as PEG degraded, the relative amounts of low molecular weight PEG oligomers increased, while those of high molecular weight decreased. The degradation of PEG oligomers in a naturally aged gel ink was consistent with those in the artificially aged samples, but occurred more slowly. This study not only provided a new method for discriminating carbon-based black gel ink entries, but also offered a new approach for studying the relative ink dating of carbon-based black gel ink entries. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Mango butter emulsion gels as cocoa butter equivalents: physical, thermal, and mechanical analyses.

    Science.gov (United States)

    Sagiri, Sai S; Sharma, Vijeta; Basak, Piyali; Pal, Kunal

    2014-11-26

    The search for cocoa butter equivalents in food and pharmaceutical industries has been gaining importance. In the present study, mango butter was explored as cocoa butter equivalent. Aqueous gelatin solution (20% w/w) containing cocoa butter and mango butter water-in-oil (fat) type emulsion gels were prepared by hot emulsification method. XRD and DSC melting profiles suggested the presence of unstable polymorphic forms (α and β') of fats in the emulsion gels. The crystal size and solid fat content analyses suggested that the presence of aqueous phase might have hindered the transformation of unstable polymorphic forms to stable polymorphic form (β) in the emulsion gels. Fat crystals in the emulsion gels were formed by instantaneous nucleation via either uni- or bidimensional growth (Avrami analysis). The viscoelastic nature of the emulsion gels was evaluated by modified Peleg's analysis (stress relaxation study). Results inferred that the physical, thermal, and mechanical properties of mango butter emulsion gels are comparable to those of cocoa butter emulsion gels. On the basis of preliminary studies, it was suggested that the mango butter emulsion gels may have potential to be used as cocoa butter equivalents.

  20. Stabilized aqueous gels and uses thereof

    Energy Technology Data Exchange (ETDEWEB)

    Swanson, B.L.

    1978-08-29

    New improved aqueous gels, and methods of using same in contacting subterranean formations, are provided. The gels are prepared by gelling an aqueous brine having incorporated therein a water-soluble cellulose ether such as a carboxymethylcellulose (CMC), and are rendered more stable to decomposition by incorporating a sulfoalkylated tannin stabilizing agent, such as a sulfomethylated quebracho (SMQ), in the gel during the preparation thereof.

  1. Gel catalysts that switch on and off

    Science.gov (United States)

    Wang, Guoqiang; Kuroda, Kenichi; Enoki, Takashi; Grosberg, Alexander; Masamune, Satoru; Oya, Taro; Takeoka, Yukikazu; Tanaka, Toyoichi

    2000-01-01

    We report development of a polymer gel with a catalytic activity that can be switched on and off when the solvent composition is changed. The gel consists of two species of monomers. The major component, N-isopropylacrylamide, makes the gel swell and shrink in response to a change in composition of ethanol/water mixtures. The minor component, vinylimidazole, which is capable of catalysis, is copolymerized into the gel network. The reaction rate for catalytic hydrolysis of p-nitrophenyl caprylate was small when the gel was swollen. In contrast, when the gel was shrunken, the reaction rate increased 5 times. The activity changes discontinuously as a function of solvent composition, thus the catalysis can be switched on and off by an infinitesimal change in solvent composition. The kinetics of catalysis by the gel in the shrunken state is well described by the Michaelis–Menten formula, indicating that the absorption of the substrate by the hydrophobic environment created by the N-isopropylacrylamide polymer in the shrunken gel is responsible for enhancement of catalytic activity. In the swollen state, the rate vs. active site concentration is linear, indicating that the substrate absorption is not a primary factor determining the kinetics. Catalytic activity of the gel is studied for substrates with various alkyl chain lengths; of those studied the switching effect is most pronounced for p-nitrophenyl caprylate. PMID:10954747

  2. Conducting polymer electrodes for gel electrophoresis.

    Directory of Open Access Journals (Sweden)

    Katarina Bengtsson

    Full Text Available In nearly all cases, electrophoresis in gels is driven via the electrolysis of water at the electrodes, where the process consumes water and produces electrochemical by-products. We have previously demonstrated that π-conjugated polymers such as poly(3,4-ethylenedioxythiophene (PEDOT can be placed between traditional metal electrodes and an electrolyte to mitigate electrolysis in liquid (capillary electroosmosis/electrophoresis systems. In this report, we extend our previous result to gel electrophoresis, and show that electrodes containing PEDOT can be used with a commercial polyacrylamide gel electrophoresis system with minimal impact to the resulting gel image or the ionic transport measured during a separation.

  3. Conducting polymer electrodes for gel electrophoresis.

    Science.gov (United States)

    Bengtsson, Katarina; Nilsson, Sara; Robinson, Nathaniel D

    2014-01-01

    In nearly all cases, electrophoresis in gels is driven via the electrolysis of water at the electrodes, where the process consumes water and produces electrochemical by-products. We have previously demonstrated that π-conjugated polymers such as poly(3,4-ethylenedioxythiophene) (PEDOT) can be placed between traditional metal electrodes and an electrolyte to mitigate electrolysis in liquid (capillary electroosmosis/electrophoresis) systems. In this report, we extend our previous result to gel electrophoresis, and show that electrodes containing PEDOT can be used with a commercial polyacrylamide gel electrophoresis system with minimal impact to the resulting gel image or the ionic transport measured during a separation.

  4. Synthesis and Characterization of Types A and B Gelatin Methacryloyl for Bioink Applications

    Science.gov (United States)

    Lee, Bae Hoon; Lum, Nathaniel; Seow, Li Yuan; Lim, Pei Qi; Tan, Lay Poh

    2016-01-01

    Gelatin methacryloyl (GelMA) has been increasingly considered as an important bioink material due to its tailorable mechanical properties, good biocompatibility, and ability to be photopolymerized in situ as well as printability. GelMA can be classified into two types: type A GelMA (a product from acid treatment) and type B GelMA (a product from alkali treatment). In current literature, there is little research on the comparison of type A GelMA and type B GelMA in terms of synthesis, rheological properties, and printability for bioink applications. Here, we report the synthesis, rheological properties, and printability of types A and B GelMA. Types A and B GelMA samples with different degrees of substitution (DS) were prepared in a controllable manner by a time-lapse loading method of methacrylic anhydride (MAA) and different feed ratios of MAA to gelatin. Type B GelMA tended to have a slightly higher DS compared to type A GelMA, especially in a lower feed ratio of MAA to gelatin. All the type A and type B GelMA solutions with different DS exhibited shear thinning behaviours at 37 °C. However, only GelMA with a high DS had an easy-to-extrude feature at room temperature. The cell-laden printed constructs of types A and B GelMA at 20% w/v showed around 75% cell viability. PMID:28773918

  5. Synthesis and Characterization of Types A and B Gelatin Methacryloyl for Bioink Applications

    Directory of Open Access Journals (Sweden)

    Bae Hoon Lee

    2016-09-01

    Full Text Available Gelatin methacryloyl (GelMA has been increasingly considered as an important bioink material due to its tailorable mechanical properties, good biocompatibility, and ability to be photopolymerized in situ as well as printability. GelMA can be classified into two types: type A GelMA (a product from acid treatment and type B GelMA (a product from alkali treatment. In current literature, there is little research on the comparison of type A GelMA and type B GelMA in terms of synthesis, rheological properties, and printability for bioink applications. Here, we report the synthesis, rheological properties, and printability of types A and B GelMA. Types A and B GelMA samples with different degrees of substitution (DS were prepared in a controllable manner by a time-lapse loading method of methacrylic anhydride (MAA and different feed ratios of MAA to gelatin. Type B GelMA tended to have a slightly higher DS compared to type A GelMA, especially in a lower feed ratio of MAA to gelatin. All the type A and type B GelMA solutions with different DS exhibited shear thinning behaviours at 37 °C. However, only GelMA with a high DS had an easy-to-extrude feature at room temperature. The cell-laden printed constructs of types A and B GelMA at 20% w/v showed around 75% cell viability.

  6. Preparation of continuous alumina gel fibres by aqueous sol–gel ...

    Indian Academy of Sciences (India)

    sol–gel process using aluminum-tri-isopropoxide as starting materials, and Shojaie-Bahaabad et al (2008) synthesized composite fibres (YAG/Al2O3) from an aqueous solution of aluminum powder, aluminum chloride hexahydrate and yttrium oxide by the sol–gel method. But, the preparation processes of continuous gel ...

  7. Adipose Extracellular Matrix/Stromal Vascular Fraction Gel Secretes Angiogenic Factors and Enhances Skin Wound Healing in a Murine Model

    Directory of Open Access Journals (Sweden)

    Mingliang Sun

    2017-01-01

    Full Text Available Mesenchymal stem cells are an attractive cell type for cytotherapy in wound healing. The authors recently developed a novel, adipose-tissue-derived, injectable extracellular matrix/stromal vascular fraction gel (ECM/SVF-gel for stem cell therapy. This study was designed to assess the therapeutic effects of ECM/SVF-gel on wound healing and potential mechanisms. ECM/SVF-gel was prepared for use in nude mouse excisional wound healing model. An SVF cell suspension and phosphate-buffered saline injection served as the control. The expression levels of vascular endothelial growth factor (VEGF, basic fibroblast growth factor (bFGF, and monocyte chemotactic protein-1 (MCP-1 in ECM/SVF-gel were analyzed at different time points. Angiogenesis (tube formation assays of ECM/SVF-gel extracts were evaluated, and vessels density in skin was determined. The ECM/SVF-gel extract promoted tube formation in vitro and increased the expression of the angiogenic factors VEGF and bFGF compared with those in the control. The expression of the inflammatory chemoattractant MCP-1 was high in ECM/SVF-gel at the early stage and decreased sharply during the late stage of wound healing. The potent angiogenic effects exerted by ECM/SVF-gel may contribute to the improvement of wound healing, and these effects could be related to the enhanced inflammatory response in ECM/SVF-gel during the early stage of wound healing.

  8. Electrophoretic analysis of proteins from Mycoplasma hominis strains detected by SDS-PAGE, two-dimensional gel electrophoresis and immunoblotting

    DEFF Research Database (Denmark)

    Andersen, H; Birkelund, Svend; Christiansen, Gunna

    1987-01-01

    The proteins of 14 strains of Mycoplasma hominis were compared by SDS-PAGE in gradient gels, by two-dimensional (2D) gel electrophoresis of extracts of 35S-labelled cells and by immunoblot analysis of cell proteins. The strains examined included the M. hominis type strain PG21 and 13 others...... isolated variously from genital tract, mouth, blood, upper urinary tract and a wound. These 14 strains shared 76-99% of proteins in SDS-gradient gel analysis and 41-72% in the 2D gels. As expected, the immunoblot analysis likewise revealed the existence of an extensive common protein pattern in M. hominis...

  9. Chitosan: Gels and Interfacial Properties

    Directory of Open Access Journals (Sweden)

    Julie Nilsen-Nygaard

    2015-03-01

    Full Text Available Chitosan is a unique biopolymer in the respect that it is abundant, cationic, low-toxic, non-immunogenic and biodegradable. The relative occurrence of the two monomeric building units (N-acetyl-glucosamine and d-glucosamine is crucial to whether chitosan is predominantly an ampholyte or predominantly a polyelectrolyte at acidic pH-values. The chemical composition is not only crucial to its surface activity properties, but also to whether and why chitosan can undergo a sol–gel transition. This review gives an overview of chitosan hydrogels and their biomedical applications, e.g., in tissue engineering and drug delivery, as well as the chitosan’s surface activity and its role in emulsion formation, stabilization and destabilization. Previously unpublished original data where chitosan acts as an emulsifier and flocculant are presented and discussed, showing that highly-acetylated chitosans can act both as an emulsifier and as a flocculant.

  10. Electrophoretic analysis of proteins from Mycoplasma hominis strains detected by SDS-PAGE, two-dimensional gel electrophoresis and immunoblotting

    DEFF Research Database (Denmark)

    Andersen, H; Birkelund, Svend; Christiansen, Gunna

    1987-01-01

    The proteins of 14 strains of Mycoplasma hominis were compared by SDS-PAGE in gradient gels, by two-dimensional (2D) gel electrophoresis of extracts of 35S-labelled cells and by immunoblot analysis of cell proteins. The strains examined included the M. hominis type strain PG21 and 13 others...

  11. Effect of pioglitazone on various parameters of insulin resistance including lipoprotein subclass according to particle size by a gel-permeation high-performance liquid chromatography in newly diagnosed patients with type 2 diabetes.

    Science.gov (United States)

    Nakano, Koji; Hasegawa, Goji; Fukui, Michiaki; Yamasaki, Masahiro; Ishihara, Kiyoshi; Takashima, Tooru; Kitagawa, Yoshihiro; Fujinami, Aya; Ohta, Mitsuhiro; Hara, Hirokazu; Adachi, Tetsuo; Ogata, Masakazu; Obayashi, Hiroshi; Nakamura, Naoto

    2010-01-01

    Pioglitazone is an insulin-sensitizing agent that has been reported to have anti-arteriosclerotic effects. The aim of this study was to obtain a better understanding of the mechanism involved in the insulin sensitizing effect of pioglitazone. A total of 50 newly diagnosed patients with type 2 diabetes were enrolled in this study and divided into two groups, 25 of who were treated with 15 mg/day pioglitazone and 25 with 500 mg/day metformin for 12 weeks. Changes in various parameters of insulin resistance including lipoprotein subclass according to particle size determined by high performance liquid chromatography, as well as glucose metabolism, were monitored to determine the relationship between lipoprotein subclass and other insulin resistance parameters. Both pioglitazone and metformin treatment were associated with significant reductions in hyperglycemia, HOMA-IR and HbA1c levels. Pioglitazone treatment, but not metformin treatment resulted in significant reductions in serum large very low-density lipoprotein (VLDL: 44.5-64.0 nm) and increases in serum adiponectin levels (both net electronegative charged modified-LDL (r=0.412, P=0.0399), and inversely with changes in adiponectin level (r=-0.526, P=0.0061). The results in this study suggest that the hypoglycemic effect of pioglitazone is achieved mainly through improvement of hepatic insulin resistance, and that pioglitazone may have an antiatherosclerotic effect by decreasing serum atherogenic modified-LDL and by increasing adiponectin.

  12. Gel dosimetry: The effect of gold nanoparticles on the dose enhancement in the external radiation therapy

    Directory of Open Access Journals (Sweden)

    Hossein Khosravi

    2016-07-01

    Full Text Available Background: Normoxic type MAGICA gel dosimeters are established for dose quantification in three dimensions for radiotherapy. Objective(s: The ability of MAGICA polymer gel was assessed by experimental measurements method for studying the effect of gold nanoparticles (GNPs in dose enhancement under the external 18MV radiotherapy practices. Methods: The different GNPs concentrations were studied: 0.02mM, 0.05 mM and 0.1 mM. Then, a new formulation of MAGICA gel was synthesized. The fabricated gel was poured in the tubes (with and without the GNPs located at the water phantom. The water phantom was irradiated to 18 MV beam of a Varian linac. After 24 hours, the irradiated gels were read using a Siemens 1.5 Tesla MRI scanner. The absolute dose sat the reference points and isodose curves resulted from the experimental measurements of the gels following the external radiotherapy practices were compared. Results: The signal of non-irradiated gel samples containing GNPs showed maximum difference of the 1% compared to gel without nanoparticles. The dose enhancement factors were 1.014±0.07, 1.074±0.11and 1.161±0.15 for 0.02, 0.05 and 0.1 mM concentrations, respectively. The results demonstrate that use of GNPs embedded in polymer gels caused the enhancement of radiation. Conclusions: The results indicated that the polymer gel dosimetry method as developed and used in this study can be recommended as a reliable method for investigating the DEF of GNPs in external radiotherapy practices.

  13. Using Greener Gels to Explore Rheology

    Science.gov (United States)

    Garrett, Brendan; Matharu, Avtar S.; Hurst, Glenn A.

    2017-01-01

    A laboratory experiment was developed to investigate the rheological properties of a green calcium-cross-linked alginate gel as an alternative to the traditional borax-cross-linked poly(vinyl alcohol) gel. As borax is suspected of damaging fertility and the unborn child, a safe, green alternative is necessary. The rheological properties of a…

  14. nanocomposite hydrogels with high gel strength

    Indian Academy of Sciences (India)

    used in many fields such as hygienic products,1 agriculture,2,3 waste water treatment,4,5 drug-delivery systems6– ... commercially synthesized hectorite product was used to prepare NC gels by inverse microemulsion poly- ... 2.4 Gel strength evaluation of the nanocomposite hydrogels. The apparent viscosity was a relative ...

  15. Sodium Dedecyl Suphate Polyacrilamide Gel Electrophosis of ...

    African Journals Online (AJOL)

    Sodium Dedecyl Suphate Polyacrilamide Gel Electrophosis of Campylobacter coli. S.I. Smith, M.M. Ibrahim, V.N. Ezeobi, K.S. Oyedeji, K.A. Akinsinde, A.O Coker. Abstract. Campylobacter coli were characterized using sodium dodecyl sulphate-polyacrilamide gel electrophoresis (SDS-PAGE). The isolates were obtained ...

  16. Serum release boosts sweetness intensity in gels

    NARCIS (Netherlands)

    Sala, G.; Stieger, M.A.; Velde, van de F.

    2010-01-01

    This paper describes the effect of serum release on sweetness intensity in mixed whey protein isolate/gellan gum gels. The impact of gellan gum and sugar concentration on microstructure, permeability, serum release and large deformation properties of the gels was determined. With increasing gellan

  17. Fast Processing of Sol-Gel TCO

    NARCIS (Netherlands)

    Deelen, J. van; Rem, M.; Arfsten, N.; Buskens, P.P.

    2016-01-01

    TCOs are usually deposited using sputtering or chemical vapor deposition, which have a yield of typically 50-75%. The sol gel method does not need low pressure and can be done with a high precursor yield in the range of 90 – 100%. Sol gel enables also the TCO function as a planarization or

  18. Recrystallization of amylopectin in concentrated starch gels

    NARCIS (Netherlands)

    Keetels, CJAM; Oostergetel, GT; vanVliet, T

    The relation between the recrystallization of amylopectin and the increase in stiffness of starch gels during storage was studied by various techniques. From transmission electron microscopy it was concluded that the size of the crystalline domains in retrograded 30% w/w potato starch gels was about

  19. Silica gel matrix immobilized Chlorophyta hydrodictyon africanum ...

    African Journals Online (AJOL)

    Chlorophyta hydrodictyon africanum was immobilized on a silica gel matrix to improve its mechanical properties. The algae-silica gel adsorbent was used for batch sorption studies of a cationic dye, methylene blue (MB). Optimum adsorption was obtained with a dosage of 0.8 g bio sorbent. Results from sorption studies ...

  20. Preliminary study of diffusion effects in Fricke gel dosimeters

    International Nuclear Information System (INIS)

    Quiroga, A.; Vedelago, J.; Valente, M.

    2014-08-01

    Diffusion of ferric ions in ferrous sulfate (Fricke) gels represents one of the main drawbacks of some radiation detectors, like Fricke gel dosimeters. In practice, this disadvantage can be overcome by prompt dosimeter analysis, constraining strongly the time between irradiation and analysis. Due to required integral accuracy levels, special dedicated protocols are implemented with the aim of minimizing signal blurring due to diffusion effects. This work presents dedicated analytic modelling and numerical calculations of diffusion coefficients in Fricke gel radiation sensitive material. Samples are optically analysed by means of visible light transmission measurements capturing images with a Ccd camera provided with a monochromatic 585 nm filter corresponding to the X O-infused Fricke solution absorbance peak. Dose distributions in Fricke gels are suitably delivered in order to assess specific initial conditions further studied by periodical sample image acquisitions. In a first analytic approach, experimental data are fit with linear models in order to achieve a value for the diffusion coefficient. The second approach to the problem consists on a group of computational algorithms based on inverse problem formulation, along with suitable 2D diffusion model capable of estimating diffusion coefficients by fitting the obtained algorithm numerical solutions with the corresponding experimental data. Comparisons are performed by introducing an appropriate functional in order to analyse both experimental and numerical values. Solutions to second order diffusion equation are calculated in the framework of a dedicated method that incorporates Finite Element Method. Moreover, optimised solutions can be attained by gradient type minimisation algorithms. Knowledge about diffusion coefficient for Fricke gel radiation detector might be helpful in accounting for effects regarding elapsed time between dosimeter irradiation and further analysis. Hence, corrections might be included

  1. Preliminary study of diffusion effects in Fricke gel dosimeters

    Energy Technology Data Exchange (ETDEWEB)

    Quiroga, A. [Centro de Investigacion y Estudios de Matematica de Cordoba, Oficina 318 FaMAF - UNC, Ciudad Universitaria, 5000 Cordoba (Argentina); Vedelago, J. [Laboratorio de Investigaciones e Instrumentacion en Fisica Aplicada a la Medicina e Imagenes por Rayos X, Laboratorio 448 FaMAF - UNC, Ciudad Universitaria, 5000 Cordoba (Argentina); Valente, M., E-mail: aiquiroga@famaf.unc.edu [Instituto de Fisica Enrique Gaviola, Oficina 102 FaMAF - UNC, Av. Luis Medina Allende, Ciudad Universitaria, 5000 Cordoba (Argentina)

    2014-08-15

    Diffusion of ferric ions in ferrous sulfate (Fricke) gels represents one of the main drawbacks of some radiation detectors, like Fricke gel dosimeters. In practice, this disadvantage can be overcome by prompt dosimeter analysis, constraining strongly the time between irradiation and analysis. Due to required integral accuracy levels, special dedicated protocols are implemented with the aim of minimizing signal blurring due to diffusion effects. This work presents dedicated analytic modelling and numerical calculations of diffusion coefficients in Fricke gel radiation sensitive material. Samples are optically analysed by means of visible light transmission measurements capturing images with a Ccd camera provided with a monochromatic 585 nm filter corresponding to the X O-infused Fricke solution absorbance peak. Dose distributions in Fricke gels are suitably delivered in order to assess specific initial conditions further studied by periodical sample image acquisitions. In a first analytic approach, experimental data are fit with linear models in order to achieve a value for the diffusion coefficient. The second approach to the problem consists on a group of computational algorithms based on inverse problem formulation, along with suitable 2D diffusion model capable of estimating diffusion coefficients by fitting the obtained algorithm numerical solutions with the corresponding experimental data. Comparisons are performed by introducing an appropriate functional in order to analyse both experimental and numerical values. Solutions to second order diffusion equation are calculated in the framework of a dedicated method that incorporates Finite Element Method. Moreover, optimised solutions can be attained by gradient type minimisation algorithms. Knowledge about diffusion coefficient for Fricke gel radiation detector might be helpful in accounting for effects regarding elapsed time between dosimeter irradiation and further analysis. Hence, corrections might be included

  2. Functional Nanofibers and Colloidal Gels: Key Elements to Enhance Functionality

    Science.gov (United States)

    Vogel, Nancy Amanda

    material so that prolonged release can be readily achieved from highly water soluble nanofibers. The final research theme focuses on gaining a fundamental understanding of a new class of materials, nanodiamond, so that a desired microstructure can be achieved via functionalization or manipulating processing parameters. In particular, we utilize both steady and dynamic rheology techniques to systematically investigate systems of nanodiamonds dispersed in model nonpolar (mineral oil) and polar (glycerol) media. In both cases, selfsupporting colloidal gels form at relatively low nanodiamond content; however, the gel behavior is highly dependent on the type of media used. Nanodiamonds dispersed in mineral oil exhibit characteristic colloidal gel behavior, with a rheological response that is independent of both frequency and time. However, nanodiamonds dispersed in glycerol exhibit a time dependent response, with the strength of the colloidal gels increasing several orders of magnitude. We attribute these rheological differences to changes in solvent complexity, where new particle-solvent and particle-particle interactions have the potential to delay optimal gel formation. In addition to colloidal gel formation, we use large oscillatory strains to probe the effect of processing parameters on microstructure disruption and recovery. The results indicate that the formation and rearrangement of the nanodiamond microstructures are concentration dependent for both media types; however, the recovery after breakdown is different for each system. Recovery of the nanodiamond/mineral oil gels is incomplete, with the strength of the recovered gel being significantly reduced. In contrast, the original strength of the nanodiamond/glycerol gels is recoverable as the system restructures with time. The practical implications of these results are significant as it suggest that shear history and solvent polarity play a dominant role in nanodiamond processing.

  3. Polymer architecture of magnetic gels: a review

    Science.gov (United States)

    Weeber, Rudolf; Hermes, Melissa; Schmidt, Annette M.; Holm, Christian

    2018-02-01

    In this review article, we provide an introduction to ferrogels, i.e. polymeric gels with embedded magnetic particles. Due to the interplay between magnetic and elastic properties of these materials, they are promising candidates for engineering and biomedical applications such as actuation and controlled drug release. Particular emphasis will be put on the polymer architecture of magnetic gels since it controls the degrees of freedom of the magnetic particles in the gel, and it is important for the particle-polymer coupling determining the mechanisms available for the gel deformation in magnetic fields. We report on the different polymer architectures that have been realized so far, and provide an overview of synthesis strategies and experimental techniques for the characterization of these materials. We further focus on theoretical and simulational studies carried out on magnetic gels, and highlight their contributions towards understanding the influence of the gels’ polymer architecture.

  4. FTIR thermal analysis on organofunctionalized silica gel

    Directory of Open Access Journals (Sweden)

    Foschiera José L.

    2001-01-01

    Full Text Available Silica gel modified with organic groups is widely used as a stationary phase for liquid chromatography. Grafting synthesis can be used to obtain stable modified silica gel surfaces. In this work, silica gel (10 nm of pore diameter and surface area of 320 m² g-1 was chemically modified with 3-chloropropyltrimethoxysilane or 3-aminopropyltrimethoxysilane and reacted with aniline, p-anisidine, benzylamine and 3-phenylpropylchloride in order to yield aromatic groups immobilized on the silica gel surface. Infrared spectroscopy was utilized for characterization of the aromatic groups grafted on the silica gel surface, using a quartz cell. The solids were heated at several temperatures in high vacuum and the infrared band areas of the organic groups were used to evaluate the thermal stability.

  5. Recent Advances in Supramolecular Gels and Catalysis.

    Science.gov (United States)

    Fang, Weiwei; Zhang, Yang; Wu, Jiajie; Liu, Cong; Zhu, Haibo; Tu, Tao

    2018-04-04

    Over the past two decades, supramolecular gels have attracted significant attention from scientists in diverse research fields and have been extensively developed. This review mainly focuses on the significant achievements in supramolecular gels and catalysis. First, by incorporating diverse catalytic sites and active organic functional groups into gelator molecules, supramolecular gels have been considered as a novel matrix for catalysis. In addition, these rationally designed supramolecular gels also provide a variety of templates to access metal nanocomposites, which may function as catalysts and exhibit high activity in diverse catalytic transformations. Finally, as a new kind of biomaterial, supramolecular gels formed in situ by self-assembly triggered by catalytic transformations are also covered herein. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. The evaluation of collagen gel with various connection states by using MRI

    International Nuclear Information System (INIS)

    Kudo, Hiroki; Mukai, Naoki; Gouping, Chen; Numanno, Tomokazu; Honma, Kazuhiro; Tateishi, Tetsuya; Miyanaga, Yutaka; Miyakawa, Syumpei

    2008-01-01

    To noninvasively evaluate the connection states of collagen fiber, a characterizing factor of the physical property, is considered to be helpful in the evaluation of cartilage functions. The purpose of this study was to examine how the connection states of collagen influence the MRI parameters by evaluating the collagen gel with various connection states using MRI. MRI was performed to six type I collagen gel samples with various connection status and a water sample. The evaluation parameters included T1 relaxation time, T2 relaxation time, and diffusion coefficient. With regard to gel samples with cross-links, the T2 relaxation time was shortened in proportion to the dose of glutaraldehyde. It is considered that as the glutaraldehyde concentration increases, the distance between protons in water molecules decreases; this is followed by a stronger bipole-bipole interaction, resulting in a shorter T2 relaxation time. The diffusion coefficient for gel samples with cross-links also decreased with increasing glutaraldehyde concentrations. However, gel samples without glutaraldehyde were almost the same as that of the water. This result suggested that the degree of entrapment of water inside the gel samples without cross-links, even when it converted into gel, was found to be nearly equal to that of the free water

  7. Sol-gel bonding of silicon wafers

    International Nuclear Information System (INIS)

    Barbe, C.J.; Cassidy, D.J.; Triani, G.; Latella, B.A.; Mitchell, D.R.G.; Finnie, K.S.; Short, K.; Bartlett, J.R.; Woolfrey, J.L.; Collins, G.A.

    2005-01-01

    Sol-gel bonds have been produced between smooth, clean silicon substrates by spin-coating solutions containing partially hydrolysed silicon alkoxides. The two coated substrates were assembled and the resulting sandwich fired at temperatures ranging from 60 to 600 deg. C. The sol-gel coatings were characterised using attenuated total reflectance Fourier transform infrared spectroscopy, ellipsometry, and atomic force microscopy, while the corresponding bonded specimens were investigated using scanning electron microscopy and cross-sectional transmission electron microscopy. Mechanical properties were characterised using both microindentation and tensile testing. Bonding of silicon wafers has been successfully achieved at temperatures as low as 60 deg. C. At 300 deg. C, the interfacial fracture energy was 1.55 J/m 2 . At 600 deg. C, sol-gel bonding provided superior interfacial fracture energy over classical hydrophilic bonding (3.4 J/m 2 vs. 1.5 J/m 2 ). The increase in the interfacial fracture energy is related to the increase in film density due to the sintering of the sol-gel interface with increasing temperature. The superior interfacial fracture energy obtained by sol-gel bonding at low temperature is due to the formation of an interfacial layer, which chemically bonds the two sol-gel coatings on each wafer. Application of a tensile stress on the resulting bond leads to fracture of the samples at the silicon/sol-gel interface

  8. Calcium Impact on Milk Gels Formation

    DEFF Research Database (Denmark)

    Koutina, Glykeria

    enriched dairy products. Calcium gels can be produced by addition of a calcium salt and heat treatment at temperatures higher than 70 oC for several minutes. The combination of heat treatment and calcium addition to milk with pH values between 6.6 and 5.6, will produce calcium milk gels with unique...... and dense gel structure and with little seperation of whey due to participation of calcium to the final gel structure. On the other hand, the combination of heat treatment and calcium addition to milk with pH values lower than 5.6 will still produce gel structures which are dominated by the decrease of p...... to be formed. In addition the low amount of micellar calcium caused a more compact gel structure with many protein aggregates. The results of this study highlighted the importance of calcium for the formation of acid, calcium and rennet gels. The content and the interactions of calcium with proteins during...

  9. Drying and shrinkage of polymer gels

    Directory of Open Access Journals (Sweden)

    S. S. Waje

    2005-06-01

    Full Text Available The polymer hydrogel was synthesized by photo-polymerization process (UV light, 60 ºC in presence of Photo-initiator (IrgacureR and Cross-linker (NN'-methylene bisacrylamide; MBAM. In the present work, the drying of polymer hydrogel was carried out to study the effect of temperature, gel-sheet thickness, monomer ratio of acryl acid to acrylamide (AA/AM, concentration of MBAM and quantity of monomers. A correlation has been developed for modified sheet thickness as a function of contraction coefficient and degree of drying. Effective diffusivity was estimated from Fickian-diffusive model considering modified sheet thickness and was found to be in the range of 1.1 ´ 10-10-5.93 ´ 10-10 m²/s. The activation energy obtained using Arrhenius type equation was found to be in the range of 2979-10737 kJ/kmol H2O. The drying behavior shows an initial shoot-up in drying rate followed by constant rate and two falling rate periods.

  10. Application of melanin-free ink as a new antioxidative gel enhancer in sardine surimi gel.

    Science.gov (United States)

    Vate, Naveen Kumar; Benjakul, Soottawat; Agustini, Tri Winarni

    2015-08-30

    The squid ink that is discarded as waste during processing can be effectively utilised as a gel enhancer in surimi gels, especially those prepared from dark-fleshed fish which have poor gel properties. It also acts as an antioxidant, inhibiting lipid oxidation. This investigation aimed to study the effect of melanin-free ink (MFI) from splendid squid (Loligo formosana) on properties and oxidative stability of surimi gel from sardine (Sardinella albella). MFI (0-0.1 g kg(-1) surimi) increased the breaking force and deformation of sardine surimi gel in a dose-dependent manner (P 0.05). The expressible moisture content of gels decreased as the levels of MFI increased (P < 0.05). Based on a microstructure study, gel added with MFI at a level of 0.08 g kg(-1) surimi was denser and finer than that of the control (without MFI). Surimi gels with MFI had lower peroxide values, thiobarbituric acid reactive substances, nonanal and 2-decenal. MFI could improve the properties of sardine surimi gel. Additionally, it was able to prevent lipid oxidation in surimi gels during refrigerated storage. © 2014 Society of Chemical Industry.

  11. Simple and practical staining of DNA with GelRed in agarose gel electrophoresis.

    Science.gov (United States)

    Huang, Qing; Baum, Larry; Fu, Wei-Ling

    2010-01-01

    Although SYBR Gold or SYBR Green I have been used in the loading buffer as a DNA stain safer than ethidium bromide for agarose gel electrophoresis, electrophoretic mobility of DNA is altered and thus DNA fragment size cannot be accurately determined. A method using GelRed in the loading buffer was developed to stain DNA fragments in agarose gel electrophoresis. Among various concentrations of GelRed, SYBR Gold, or SYBR Green I tested in the loading buffer, only the highest tested concentration of GelRed, i.e., 100x GelRed, did not change band mobility. Evaluations using various sizes of PCR products at different concentrations further confirmed that 100x GelRed could be used to accurately determine DNA fragment size. The reagent can be stored at 4 degrees C for at least 1 year without a decrease in staining sensitivity. The 100x GelRed is a sensitive and safe alternative to ethidium bromide and better than either SYBR Gold or SYBR Green I for size determination in agarose gel electrophoresis. Our laboratory now uses the GelRed method routinely with great consistency and success.

  12. Pulsed field gel electrophoresis a practical guide

    CERN Document Server

    Birren, Bruce

    1993-01-01

    Pulsed Field Gel Electrophoresis: A Practical Guide is the first laboratory manual to describe the theory and practice of this technique. Based on the authors' experience developing pulsed field gel instruments and teaching procedures, this book provides everything a researcher or student needs to know in order to understand and carry out pulsed field gel experiments. Clear, well-tested protocols assume only that users have a basic familiarity with molecular biology. Thorough coverage of useful data, theory, and applications ensures that this book is also a lasting resource for more adv

  13. Exopolysaccharide influence on acid gel formation

    Directory of Open Access Journals (Sweden)

    K. Yoanidu

    2017-06-01

    Full Text Available Abstract. Turbidimetric monitoring of milk coagulation was conducted in situ. Milk gel was produced by acidification with the use of three strains of starter culture. These strains were characterized by various acidification rate and exopolysaccharides (EPS production. The concentrations of EPS affect mostly the pH of gel formation (5.53 - low EPS – producing strain; 5.33 - medium EPS – producing strain; 5.46 - high EPS – producing strain whereas the time of gel formation depends on the various rate of acidification of all three strains.

  14. Enhancing the performance of dye-sensitized solar cells by incorporating nanosilicate platelets in gel electrolyte

    KAUST Repository

    Lai, Yi-Hsuan

    2009-10-01

    Two kinds of gel-type dye-sensitized solar cells (DSSCs), composed of two types of electrolytes, were constructed and the respective cell performance was evaluated in this study. One electrolyte, TEOS-Triton X-100 gel, was based on a hybrid organic/inorganic gel electrolyte made by the sol-gel method and the other was based on poly(vinyidene fluoride-co-hexafluoro propylene) (PVDF-HFP) copolymer. TEOS-Triton X-100 gel was based on the reticulate structure of silica, formed by hydrolysis, and condensation of tetraethoxysilane (TEOS), while its organic subphase was a mixture of surfactant (Triton X-100) and ionic liquid electrolytes. Both DSSC gel-type electrolytes were composed of iodine, 1-propy-3-methyl-imidazolium iodide, and 3-methoxypropionitrile to create the redox couple of I3 -/I-. Based on the results obtained from the I-V characteristics, it was found that the optimal iodine concentrations for the TEOS-Triton X-100 gel electrolyte and PVDF-HFP gel electrolyte are 0.05 M and 0.1 M, respectively. Although the increase in the iodine concentration could enhance the short-circuit current density (JSC), a further increase in the iodine concentration would reduce the JSC due to increased dark current. Therefore, the concentration of I2 is a significant factor in determining the performance of DSSCs. In order to enhance cell performance, the addition of nanosilicate platelets (NSPs) in the above-mentioned gel electrolytes was investigated. By incorporating NSP-Triton X-100 into the electrolytes, the JSC of the cells increased due to the decrease of diffusion resistance, while the open circuit voltage (VOC) remained almost the same. As the loading of the NSP-Triton X-100 in the TEOS-Triton X-100 gel electrolyte increased to 0.5 wt%, the JSC and the conversion efficiency increased from 8.5 to 12 mA/cm2 and from 3.6% to 4.7%, respectively. However, the JSC decreased as the loading of NSP-Triton X-100 exceeded 0.5 wt%. At higher NSP-Triton X-100 loading, NSPs acted as

  15. Confocal Rheology Probes the Structure and Mechanics of Collagen through the Sol-Gel Transition.

    Science.gov (United States)

    Tran-Ba, Khanh-Hoa; Lee, Daniel J; Zhu, Jieling; Paeng, Keewook; Kaufman, Laura J

    2017-10-17

    Fibrillar type I collagen-based hydrogels are commonly used in tissue engineering and as matrices for biophysical studies. Mechanical and structural properties of these gels are known to be governed by the conditions under which fibrillogenesis occurs, exhibiting variation as a function of protein concentration, temperature, pH, and ionic strength. Deeper understanding of how macroscopic structure affects viscoelastic properties of collagen gels over the course of fibrillogenesis provides fundamental insight into biopolymer gel properties and promises enhanced control over the properties of such gels. Here, we investigate type I collagen fibrillogenesis using confocal rheology-simultaneous confocal reflectance microscopy, confocal fluorescence microscopy, and rheology. The multimodal approach allows direct comparison of how viscoelastic properties track the structural evolution of the gel on fiber and network length scales. Quantitative assessment and comparison of each imaging modality and the simultaneously collected rheological measurements show that the presence of a system-spanning structure occurs at a time similar to rheological determinants of gelation. Although this and some rheological measures are consistent with critical gelation through percolation, additional rheological and structural properties of the gel are found to be inconsistent with this theory. This study clarifies how structure sets viscoelasticity during collagen fibrillogenesis and more broadly highlights the utility of multimodal measurements as critical test-beds for theoretical descriptions of complex systems. Copyright © 2017 Biophysical Society. Published by Elsevier Inc. All rights reserved.

  16. Preparation of UO2 dense spherical particles by sol-gel technique

    International Nuclear Information System (INIS)

    Urbanek, V.; Dolezal, J.

    1977-01-01

    The results of the basic research and development of processes of preparation of dense UO 2 spherical particles by sol-gel technique are presented. Attention was paid to the study of chemistry of internal gelation step in the uranylnitrate-urea-hexamethylentetramine system. The existence regions of several stable gels with different properties were established in connection with variable ratio of basic gel's components and the appropriate ''Phase diagrams'' were drawn. From these diagrams, two of the most interesting types of uranyl gels were chosen for the subsequent thermal processing which included drying, reduction and sintering. The detailed studies of each step of the whole process enabled preparation of UO 2 dense spheres with well defined microstructure

  17. Exploratory experiments on the feasibility of Th and Pu sol-gel particles

    International Nuclear Information System (INIS)

    Vanhellemont, G.; Beullens, J.; Bairiot, H.

    1965-05-01

    The sol-gel process as developed by the O.E.C.D. Dragon Project has been applied by the Plutonium Project at Mol to determine the feasibility of producing spherical particles containing Th02, Pu02 and C, in the proportions necessary to fabricate thorium-plutonium carbide kernels for irradiation specimens and for fuel cartridges for the Dragon Reactor Experiment. The process has been extended successfully to the preparation of thorium and plutonium gels, having a significant excess of carbon, with the object of evaluating the feasibility of the sol-gel process for the production of Th, C-10 type kernels. Other experiments have been performed to test the feasibility of incorporating U02 powder into the gel spheres. By using this technique, U to Th ratios of up to 9:1 have been obtained. (author)

  18. COMPARATIVE ANALYSIS OF BLOOD GROUPING IN HEALTHY BLOOD DONOR USING GEL CARD TECHNIQUE AND TUBE METHOD

    Directory of Open Access Journals (Sweden)

    Muhammad Usman

    2016-12-01

    Full Text Available Blood grouping is a vital test in pre-transfusion testing. Both tube and gel agglutination assays are used for ABO grouping. The main object of this study was to compare ABO grouping and D typing on tube and gel agglutination assay in order to assess the efficacy of each technique. A total of 100 healthy blood donors irrespective of age and sex were included in this study. Results showed that there is no significant difference between these two techniques. However, in 10 samples it was detected that the reaction strength in serum ABO grouping by gel agglutination assay is varied by only one grade when compared to tube agglutination assay. Due to numerous positive effects of gel assay it is more beneficial to implement this technique in the setups where blood banks bear heavy routine work load.

  19. Synthesis and Test of 'New' Gel-Type Lithium Electrolytes

    National Research Council Canada - National Science Library

    Scrosati, Bruno

    1994-01-01

    In this 6th two-month period we have continued the characterization of PMMA-based electrolyte membranes by examining the phenomena occurring at the interface between these membranes and the lithium...

  20. Buckling of paramagnetic chains in soft gels.

    Science.gov (United States)

    Huang, Shilin; Pessot, Giorgio; Cremer, Peet; Weeber, Rudolf; Holm, Christian; Nowak, Johannes; Odenbach, Stefan; Menzel, Andreas M; Auernhammer, Günter K

    2016-01-07

    We study the magneto-elastic coupling behavior of paramagnetic chains in soft polymer gels exposed to external magnetic fields. To this end, a laser scanning confocal microscope is used to observe the morphology of the paramagnetic chains together with the deformation field of the surrounding gel network. The paramagnetic chains in soft polymer gels show rich morphological shape changes under oblique magnetic fields, in particular a pronounced buckling deformation. The details of the resulting morphological shapes depend on the length of the chain, the strength of the external magnetic field, and the modulus of the gel. Based on the observation that the magnetic chains are strongly coupled to the surrounding polymer network, a simplified model is developed to describe their buckling behavior. A coarse-grained molecular dynamics simulation model featuring an increased matrix stiffness on the surfaces of the particles leads to morphologies in agreement with the experimentally observed buckling effects.

  1. Evaluation of wheat by polyacrylamide gel electrophoresis

    African Journals Online (AJOL)

    PRECIOUS

    2010-01-11

    04, Inqulab-91 and Rawal-. 87 were evaluated for analysis of variability in seed storage proteins by using sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). Electrophorogram for each variety were scored ...

  2. Sodium Dedecyl Suphate Polyacrilamide Gel Electrophosis of ...

    African Journals Online (AJOL)

    polyacrilamide gel electrophoresis (SDS-PAGE). The isolates were obtained from the faeces of diarrhoeic children with the age range of 0 t 36 months attending paediatric clinic at the Lagos University Teaching Hospital (LUTH) and Obafemi Awolowo ...

  3. Preparation of zirconium molybdate gel generator

    International Nuclear Information System (INIS)

    Charoen, S.; Aungurarat, G.; Laohawilai, S.; Sukontpradit, W.; Jingjit, S.

    1994-01-01

    A procedure for preparation of 99mTc generator based on conversion to zirconium molybdate gel of 99Mo produced by neutron activation was reported. The gel was prepared from zirconium oxychloride solution pH 1.6, ammonium molybdate solution pH 3-5 and mole ratio of Zr:Mo 1:1 which had water content about 7-8%. Small generators containing 1-1.5 g of gel were eluted with average efficiencies of 77% and the activity peak in the first 3 ml of 10 ml of saline solution. The amount of Mo and Zr in eluates were below the acceptance limit. The gel generators of activity about 100 mCi were prepared and had the good performance in elutability and stability

  4. Thixotropic corrosive gels for nuclear decontamination

    International Nuclear Information System (INIS)

    Bargues, St.

    1998-01-01

    The aim of this thesis was the development of corrosive gels for metallic surface decontamination. These gels formulation, based on a powerful oxidant (the cerium IV), the nitric acid, a mineral charge (silica) and a non ionic surface-active, has been developed according to the specific constraints of the nuclear industry. The objective was to prepare thixotropic gels becoming liquid after shacking to allow an easy pulverization and coming again solid to permit a perfect adhesion on the metallic surface. This rheological study of the gels has been completed by an evaluation of their corrosive properties. The last part of the work presents an industrial utilization during two years. (A.L.B.)

  5. Thermo-physical properties of silica gel for adsorption desalination cycle

    KAUST Repository

    Thu, Kyaw

    2013-02-01

    Thermo-physical properties, surface characteristics and water vapor uptake capacity are key parameters in the selection of adsorbent for an adsorption desalination (AD) cycle. In the AD cycles, silica gel is used as adsorbent due to their high water vapor uptake capacity, reliability, repeatability and inexpensiveness as compared to other adsorbents. Three types of commercially available silica gels (Type-RD 2560,Type-A5BW and Type-A++) are investigated using a surface characteristic analyzer and their thermo-physical properties are evaluated using several analysis methods. The instrument used in this investigation employs the static volumetric method with liquid Nitrogen at 77 K as the filing fluid. The surface area of each adsorbent is studied using Brunauer-Emmett-Teller (BET) method whilst the pore size distribution (PSD) analysis is conducted with the Non-Local Density Functional Theory (NLDFT). It is observed that the Type-A++ silica gel (granular type) possesses the highest surface area of 863.6 m2/g amongst the three parent silica gels studied. It has a two-maxima or bimodal distribution pattern where the pore diameters are distributed mostly between 10 Å and 30 Å. Water vapor uptake capacity of silica gels are studied with water vapor dosage apparatus and the results show that the Type-A++ silica gel exhibits a highest equilibrium uptake at 537 cm3/g. These thermo-physical properties are essential for the design and the numerical simulation of AD cycles. © 2012 Published by Elsevier Ltd.

  6. Detection of pectinesterase in polyacrylamide gels.

    Science.gov (United States)

    Alonso, J; Rodríguez, M T; Canet, W

    1995-01-01

    A rapid and sensitive method of detecting pectinesterase activity following electrophoresis or isoelectric focusing in polyacrylamide gels is described. The method uses ruthenium red and requires no addition of substrate when making the gels, thus obviating direct enzyme-substrate contact during electrophoresis. Because of its versatility, the method can be used in a wide variety of applications, such as plant and microbial taxonomy, enzyme purification and characterization, or as an analytical method in fresh and processed plant technology.

  7. Improving calibration accuracy in gel dosimetry

    International Nuclear Information System (INIS)

    Oldham, M.; McJury, M.; Webb, S.; Baustert, I.B.; Leach, M.O.

    1998-01-01

    A new method of calibrating gel dosimeters (applicable to both Fricke and polyacrylamide gels) is presented which has intrinsically higher accuracy than current methods, and requires less gel. Two test-tubes of gel (inner diameter 2.5 cm, length 20 cm) are irradiated separately with a 10x10cm 2 field end-on in a water bath, such that the characteristic depth-dose curve is recorded in the gel. The calibration is then determined by fitting the depth-dose measured in water, against the measured change in relaxivity with depth in the gel. Increased accuracy is achieved in this simple depth-dose geometry by averaging the relaxivity at each depth. A large number of calibration data points, each with relatively high accuracy, are obtained. Calibration data over the full range of dose (1.6-10 Gy) is obtained by irradiating one test-tube to 10 Gy at dose maximum (D max ), and the other to 4.5 Gy at D max . The new calibration method is compared with a 'standard method' where five identical test-tubes of gel were irradiated to different known doses between 2 and 10 Gy. The percentage uncertainties in the slope and intercept of the calibration fit are found to be lower with the new method by a factor of about 4 and 10 respectively, when compared with the standard method and with published values. The gel was found to respond linearly within the error bars up to doses of 7 Gy, with a slope of 0.233±0.001 s -1 Gy -1 and an intercept of 1.106±0.005 Gy. For higher doses, nonlinear behaviour was observed. (author)

  8. Conducting Polymer Electrodes for Gel Electrophoresis

    OpenAIRE

    Bengtsson, Katarina; Nilsson, Sara; Robinson, Nathaniel D

    2014-01-01

    In nearly all cases, electrophoresis in gels is driven via the electrolysis of water at the electrodes, where the process consumes water and produces electrochemical by-products. We have previously demonstrated that p-conjugated polymers such as poly(3,4-ethylenedioxythiophene) (PEDOT) can be placed between traditional metal electrodes and an electrolyte to mitigate electrolysis in liquid (capillary electroosmosis/electrophoresis) systems. In this report, we extend our previous result to gel ...

  9. Cumulative irritation comparison of adapalene gel and solution with 2 tazarotene gels and 3 tretinoin formulations.

    Science.gov (United States)

    Greenspan, Alan; Loesche, Christian; Vendetti, Nancy; Georgeian, Kathleen; Gilbert, Richard; Poncet, Michel; Baker, Michael D; Soto, Pascale

    2003-07-01

    Forty-two subjects with normal skin were enrolled in a single-center study to assess the cumulative irritancy potential of adapalene (Differin gel 0.1% and Differin solution 0.1%) compared with tazarotene (Tazorac gels 0.05% and 0.1%), tretinoin (Retin-A Micro gel 0.1%, Avita cream 0.025%, and Avita gel 0.025%), and white petrolatum (negative control). All test materials were applied randomly, under occlusion, to sites located on either side of the midline--the mid thoracic area of the subjects' backs. All patches were applied daily, Monday through Friday, to the same sites, unless the degree of reaction to a test product or adhesive necessitated removal (grade 3). Thirty-eight of the 42 subjects (90.5%) completed the study. Thirty-four of those 38 subjects (89.5%) had to discontinue using both tazarotene concentrations due to intolerance. Patch discontinuations for the remaining test materials were as follows: 7 subjects discontinued use of tretinoin microsphere gel 0.1%, 3 discontinued tretinoin cream 0.025%, 1 discontinued tretinoin gel 0.025%, and 1 discontinued adapalene gel 0.1%. None of the subjects discontinued use of the white petrolatum or the adapalene solution 0.1%. Adapalene gel and solution 0.1% were statistically (P<.01) less irritating than both tazarotene gels 0.1% and 0.05%, tretinoin microsphere gel 0.1%, and tretinoin gel 0.025%, and they were not statistically different from tretinoin gel 0.025%.

  10. Electrostatic forces in muscle and cylindrical gel systems

    Energy Technology Data Exchange (ETDEWEB)

    Millman, B.M.; Nickel, B.G.

    1980-10-01

    Repulsive pressure has been measured as a function of lattice spacing in gels of tobacco mosaic virus (TMV) and in the filament lattice of vertebrate striated muscle. External pressures up to ten atm have been applied to these lattices by an osmotic stress method. Numerical solutions to the Poisson-Boltzmann equation in hexagonal lattices have been obtained and compared to the TMV and muscle data. The theoretical curves using values for kappa calculated from the ionic strength give a good fit to experimental data from TMV gels, and an approximate fit to that from the muscle lattice, provided that a charge radius for the muscle thick filaments of approx. 16 nm is assumed. Variations in ionic strength, sarcomere length and state of the muscle give results which agree qualitatively with the theory, though a good fit between experiment and theory in the muscle case will clearly require consideration of other types of forces. We conclude that Poisson-Boltzmann theory can provide a good first approximation to the long-range electrostatic forces operating in such biological gel systems.

  11. Study of nuclear glasses alteration gel and synthesis of some model gels; Etude du gel d`alteration des verres nucleaires et synthese de gels modeles

    Energy Technology Data Exchange (ETDEWEB)

    Ricol, S.

    1995-10-05

    This work deals with the general problem of alteration of the reference nuclear glass R7T7. Attention is paid particularly to the altered layer formed at the glass surface during alteration process. In opposition to previous works, related essentially to glass dissolution kinetics based on chemical analyses of lixiviated elements, this thesis deals with alteration problems through structural studies of the reference glass and derived gel. This approach allows the determination of mechanisms for the gel formation and a better understanding of the behaviour of glasses towards lixiviation. Both approaches appeared complementary. Based on several spectroscopic techniques, this work showed the particular role of cations such as calcium, zirconium and iron. Studies of silica-based synthetic gels showed the synergic effect of formers cation and of one highly coordinated cation. The variation of the wavenumber related to Si-O-Si asymmetric stretching vibration can be correlated to O/Si ratio for ternary systems Si/Na/Zr. On the contrary, the Si losses of the materials depend on the number of non-bridging oxygen atoms. In the perspective of long-term behaviour, the alteration gel presents better characteristics than initial glass. It is therefore a highly stable material in static conditions. In the same way, synthetic gels are materials with very low solubilities (much lower than the alteration gel) and could be used as confining matrices. (authors). refs., 71 figs., 37 tabs.

  12. Polymeric gels for intravaginal drug delivery.

    Science.gov (United States)

    Cook, Michael T; Brown, Marc B

    2018-01-28

    Intravaginal drug delivery can elicit a local effect, or deliver drugs systemically without hepatic first pass metabolism. There are a number of emerging areas in intravaginal drug delivery, but the vagina is a challenging route of administration, due to the clearance mechanisms present which result in poor retention of dosage forms, and the potential for irritation and other adverse reactions. Gel formulations are desirable due to the ease of application, spreading and that they cause little to no discomfort to the patient. However, these dosage forms, in particular, are poorly retained and traditional gels typically have little control over drug release rates. This has led to a large number of studies on improving the retention of vaginal gels and modulating the controlled release of drugs from the gel matrix. This review outlines the anatomy and physiology of the vagina, focussing on areas relevant to drug delivery. Medical applications of vaginally administered medicines is then discussed, followed by an overview of polymeric gels in intravaginal drug delivery. The sensorial properties of intravaginal gels, and how these relate to user compliance are also summarised. Finally, some important barriers to marketing approval are described. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Basic investigations on LCV micelle gel

    Science.gov (United States)

    Ebenezer, S. B.; Rafic, M. K.; Ravindran, P. B.

    2013-06-01

    The aim of this study was to investigate the feasibility of using Leuco Crystal Violet (LCV) based micelle gel dosimeter as a quality assurance tool in radiotherapy applications. Basic properties such as absorption coefficient and diffusion of LCV gel phantom over time were evaluated. The gel formulation consisted of 25 mM Trichloroacetic acid, 1mM LCV, 4 mM Triton X-100, 4% gelatin by mass and distilled water. The advantages of using this gel are its tissue equivalence, easy and less preparation time, lower diffusion rate and it can be read with an optical scanner. We were able to reproduce some of the results of Babic et al. The peak absorption was found to be at 600 nm and hence a matrix of yellow LEDs was used as light source. The profiles obtained from projection images confirmed the diffusion of LCV gel after 6 hours of irradiation. Hence the LCV gel phantom should be read before 6 hours post irradiation to get accurate dose information as suggested previously.

  14. Gel nano-particulates against radioactivity; Des nanoparticules en gel contre la radioactivite

    Energy Technology Data Exchange (ETDEWEB)

    Deroin, Ph

    2004-11-01

    The Argonne research center (USA) has developed a 'super-gel' compound, a polymer close to those used in baby's diapers, which can reach a 90% efficiency in the radioactive decontamination of porous materials, like bricks or concrete. The contaminated materials are sprayed with a mixture of polymer gel and wetting agent with nano-particulates in suspension. Under the action of the wetting agent, radioactivity migrates from the pores to the gel and is trapped by the nano-particulates. The drying and recycling of the gel allows to reduce the volume of radioactive wastes. Short paper. (J.S.)

  15. Silicon gel sheeting for preventing and treating hypertrophic and keloid scars.

    Science.gov (United States)

    O'Brien, L; Pandit, A

    2006-01-25

    Keloid and hypertrophic scars are common and are caused by a proliferation of dermal tissue following skin injury. They cause functional and psychological problems for patients, and their management can be difficult. The use of silicon gel sheeting to prevent and treat hypertrophic scarring is still relatively new, and started in 1981 with treatment of burn scars. To determine the effectiveness of silicon gel sheeting for: (1) prevention of hypertrophic or keloid scarring in people with newly healed wounds (e.g. post surgery); (2) treatment of established scarring in people with existing keloid or hypertrophic scars. Trials were identified from searches of the Cochrane Wounds Group Specialised Register (searched September 2005), the Cochrane Central Register of Controlled Trials (The Cochrane Library Issue 3, 2005); MEDLINE (1989 to June 2002); EMBASE (1988 to May 2002); CINAHL (1982 to May 2002) and reference lists of articles and relevant reviews. The major supplier of silicon gel sheeting (Smith and Nephew) was approached for details of unpublished, ongoing and recently published trials. Any randomised or quasi-randomised controlled trials, or controlled clinical trials comparing silicon gel sheeting for prevention or treatment of hypertrophic or keloid scars against no treatment, placebo, or any other treatment type except surgery. All relevant trials were assessed for methodological quality. Data were extracted independently by both reviewers using a standardized form, and the results cross-checked. All trials, meeting the selection criteria were assessed for methodological quality. Thirteen trials, involving 559 people, ranging in age from 2 to 81 years, were included in the review. The trials compared adhesive silicon gel sheeting with control; non-silicon gel sheeting; silicon gel plates with added Vitamin E; laser therapy; triamcinolone acetonide injection, and non-adhesive silicon gel sheeting. In the prevention studies, when compared with a no treatment

  16. Gel-aided sample preparation (GASP)--a simplified method for gel-assisted proteomic sample generation from protein extracts and intact cells.

    Science.gov (United States)

    Fischer, Roman; Kessler, Benedikt M

    2015-04-01

    We describe a "gel-assisted" proteomic sample preparation method for MS analysis. Solubilized protein extracts or intact cells are copolymerized with acrylamide, facilitating denaturation, reduction, quantitative cysteine alkylation, and matrix formation. Gel-aided sample preparation has been optimized to be highly flexible, scalable, and to allow reproducible sample generation from 50 cells to milligrams of protein extracts. This methodology is fast, sensitive, easy-to-use on a wide range of sample types, and accessible to nonspecialists. © 2014 The Authors. PROTEOMICS published by Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Iron porphyrins doped sol-gel glasses: a chemometric study

    International Nuclear Information System (INIS)

    Sacco, Herica C.; Vidoto, Ednalva A.; Nascimento, Otaciro R.

    2000-01-01

    This paper describes the optimized conditions for preparation of iron porphyrin-template doped silica Fe PDS-template) obtained by the sol-gel process. The following porphyrins (Fe P) were used: Fe TFPP Cl, Fe TDCSPP(Na) 4 Cl and Fe TCPP(Na) 4 Cl. Pyridine or 4-phenylimidazole was used as template. The variables that present significant influence on iron porphyrin loading on xerogel were identified and the values that maximize the iron porphyrin loading on xerogel were established . The variables (Solvent volume, fractional factorial design in two levels, 2 5-1 type, generating 16 total experiments for each Fe P studied. (author)

  18. Iron porphyrins doped sol-gel glasses: a chemometric study

    Energy Technology Data Exchange (ETDEWEB)

    Sacco, Herica C.; Vidoto, Ednalva A.; Nascimento, Otaciro R. [Soap Paulo Univ (USP), Sao Carlos (Brazil). Inst. de Fisica; Biazzotto, Juliana C.; Serra, Osvaldo A.; Iamamoto, Yassuko [Sao Paulo Univ. (USP), Ribeirao Preto, SP (Brazil). Faculdade de Filosofia, Ciencias e Letras; Ciuffi, Katia J.; Mello, Cesar A.; Oliveira, Daniela C. de [Universidade de Franca , SP (Brazil)

    2000-07-01

    This paper describes the optimized conditions for preparation of iron porphyrin-template doped silica Fe (PDS-template) obtained by the sol-gel process. The following porphyrins (Fe P) were used: Fe TFPP Cl, Fe TDCSPP(Na){sub 4}Cl and Fe TCPP(Na){sub 4} Cl. Pyridine or 4-phenylimidazole was used as template. The variables that present significant influence on iron porphyrin loading on xerogel were identified and the values that maximize the iron porphyrin loading on xerogel were established. The variables Solvent volume, fractional factorial design in two levels, 2{sup 5-1} type, generating 16 total experiments for each Fe P studied. (author)

  19. Photoelastic colloidal gel for a high-sensitivity strain sensor

    Science.gov (United States)

    Pan, Hui; Chen, Zhixin; Zhu, Shenmin; Jiang, Chun; Zhang, Di

    2018-04-01

    Nanoparticles, having the ability to self-assemble into an ordered structure in their suspensions, analogous to liquid crystals, have attracted extensive attention. Herein, we report a new type of colloidal gel with an ordered crystal structure assembled from 1D and 2D nanoparticles. The material has high elasticity and, more interestingly, it shows significant photoelasticity. Its refractive index can be tuned under external stress and exhibits an ultra-wide dynamic range (Δn) of the order of 10‑2. Due to the large Δn, the material shows an extremely high strain sensibility of 720 nm/ε, an order of magnitude higher than the reported ones.

  20. Fricke Xylenol Gel characterization at megavoltage radiation energy

    International Nuclear Information System (INIS)

    o 3900, Monte Alegre, CEP: 14040-901, Ribeirão Preto, SP (Brazil))" data-affiliation=" (Departamento de Física, Faculdade de Filosofia, Ciências e Letras de Ribeirão Preto, DF-FFCLRP/USP, Avenida Bandeirantes, no 3900, Monte Alegre, CEP: 14040-901, Ribeirão Preto, SP (Brazil))" >Del Lama, Lucas Sacchini; o 1437, Ecoville, CEP: 82305-100, Curitiba, PR (Brazil))" data-affiliation=" (Oncoville, Centro de Excelência em Radioterapia em Curitiba, Rodovia BR-277, no 1437, Ecoville, CEP: 82305-100, Curitiba, PR (Brazil))" >Petchevist, Paulo César Dias; o 3900, Monte Alegre, CEP: 14040-901, Ribeirão Preto, SP (Brazil))" data-affiliation=" (Departamento de Física, Faculdade de Filosofia, Ciências e Letras de Ribeirão Preto, DF-FFCLRP/USP, Avenida Bandeirantes, no 3900, Monte Alegre, CEP: 14040-901, Ribeirão Preto, SP (Brazil))" >Almeida, Adelaide de

    2017-01-01

    Accurate determination of absorbed dose is of great importance in every medical application of ionizing radiation, mainly when involving biological tissues. Among different types of dosimeters, the ferrous sulfate chemical solution, known as Fricke solution, can be detached, due to its accuracy, reproducibility and linearity, been used in radiation dosimetry for over 50 years. Besides these characteristics, the Fricke Xylenol Gel (FXG), became one of the most known dosimeters for absorbed dose spatial distribution because of its high spatial resolution. In this work, we evaluated the FXG dosimeter taking into account different preparation recipes, in order to characterize its response in terms of absorbed dose range, linearity, sensitivity and fading.

  1. Fricke Xylenol Gel characterization at megavoltage radiation energy

    Energy Technology Data Exchange (ETDEWEB)

    Del Lama, Lucas Sacchini, E-mail: lucasdellama@gmail.com [Departamento de Física, Faculdade de Filosofia, Ciências e Letras de Ribeirão Preto, DF-FFCLRP/USP, Avenida Bandeirantes, n" o 3900, Monte Alegre, CEP: 14040-901, Ribeirão Preto, SP (Brazil); Petchevist, Paulo César Dias [Oncoville, Centro de Excelência em Radioterapia em Curitiba, Rodovia BR-277, n" o 1437, Ecoville, CEP: 82305-100, Curitiba, PR (Brazil); Almeida, Adelaide de [Departamento de Física, Faculdade de Filosofia, Ciências e Letras de Ribeirão Preto, DF-FFCLRP/USP, Avenida Bandeirantes, n" o 3900, Monte Alegre, CEP: 14040-901, Ribeirão Preto, SP (Brazil)

    2017-03-01

    Accurate determination of absorbed dose is of great importance in every medical application of ionizing radiation, mainly when involving biological tissues. Among different types of dosimeters, the ferrous sulfate chemical solution, known as Fricke solution, can be detached, due to its accuracy, reproducibility and linearity, been used in radiation dosimetry for over 50 years. Besides these characteristics, the Fricke Xylenol Gel (FXG), became one of the most known dosimeters for absorbed dose spatial distribution because of its high spatial resolution. In this work, we evaluated the FXG dosimeter taking into account different preparation recipes, in order to characterize its response in terms of absorbed dose range, linearity, sensitivity and fading.

  2. A systematic review and meta-analysis of the i-gel® vs laryngeal mask airway in children.

    Science.gov (United States)

    Choi, G J; Kang, H; Baek, C W; Jung, Y H; Woo, Y C; Cha, Y J

    2014-11-01

    We systematically reviewed randomised controlled trials of the i-gel® vs different types of laryngeal mask airway in children. We included nine studies. There was no evidence for differences in: rate of insertion at first attempt; insertion time; ease of insertion; or gastric tube insertion. The mean (95% CI) oropharyngeal leak pressure was 3.29 (2.25-4.34) cmH2 O higher with the i-gel, p airway, relative rate with the i-gel 0.46 (0.23-0.91), p = 0.02. We concluded that the clinical performance of the i-gel and LMA was similar, except for three outcomes that favoured the i-gel. © 2014 The Association of Anaesthetists of Great Britain and Ireland.

  3. Electrophoretic NMR measurements of lithium transference numbers in polymer gel electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Dai, H.; Sanderson, S.; Davey, J.; Uribe, F.; Zawodzinski, T.A. Jr. [Los Alamos National Lab., NM (United States). Electronics Materials and Device Research Group

    1997-05-01

    Polymer gel electrolytes are of increasing interest for plastic lithium batteries largely because of their high room temperature conductivity. Several studies have probed their conductivity and electrochemical stability but very little work has been done related to lithium transference numbers. Lithium ion transference numbers, the net number of Faradays carried by lithium upon the passage of 1 Faraday of charge across a cell, are key figures of merit for any potential lithium battery electrolytes. The authors describe here their application of electrophoretic NMR (ENMR) to the determination of transference numbers of lithium ions in polymer gel electrolytes. Two types of polymer gel electrolytes were selected for this study: PAN/PC/EC/LiX and Kynar/PC/LiX. Results obtained for the two types of gels are compared and the effects of anion, polymer-ion interactions and ion-ion interactions on lithium transference numbers are discussed. Significant differences in the behavior of transference numbers with salt concentration are observed for the two types of gels. This may be due to the extent of interaction between the polymer and the ions. Implications for solid polymer electrolytes are discussed.

  4. Utilizing whey protein isolate and polysaccharide complexes to stabilize aerated dairy gels.

    Science.gov (United States)

    O'Chiu, Emily; Vardhanabhuti, Bongkosh

    2017-05-01

    Heated soluble complexes of whey protein isolate (WPI) with polysaccharides may be used to modify the properties of aerated dairy gels, which could be formulated into novel-textured high-protein desserts. The objective of this study was to determine the effect of polysaccharide charge density and concentration within a WPI-polysaccharide complex on the physical properties of aerated gels. Three polysaccharides having different degrees of charge density were chosen: low-methoxyl pectin, high-methoxyl type D pectin, and guar gum. Heated complexes were prepared by heating the mixed dispersions (8% protein, 0 to 1% polysaccharide) at pH 7. To form aerated gels, 2% glucono-δ-lactone was added to the dispersions of skim milk powder and heated complex and foam was generated by whipping with a handheld frother. The foam set into a gel as the glucono-δ-lactone acidified to a final pH of 4.5. The aerated gels were evaluated for overrun, drainage, gel strength, and viscoelastic properties. Without heated complexes, stable aerated gels could not be formed. Overrun of aerated gel decreased (up to 73%) as polysaccharide concentration increased from 0.105 to 0.315% due to increased viscosity, which limited air incorporation. A negative relationship was found between percent drainage and dispersion viscosity. However, plotting of drainage against dispersion viscosity separated by polysaccharide type revealed that drainage decreased most in samples with high-charge-density, low-methoxyl pectin followed by those with low-charge-density, high-methoxyl type D pectin. Aerated gels with guar gum (no charge) did not show improvement to stability. Rheological results showed no significant difference in gelation time among samples; therefore, stronger interactions between WPI and high-charge-density polysaccharide were likely responsible for increased stability. Stable dairy aerated gels can be created from WPI-polysaccharide complexes. High-charge-density polysaccharides, at

  5. Controlling Gel Structure to Modulate Cell Adhesion and Spreading on the Surface of Microcapsules.

    Science.gov (United States)

    Zheng, Huizhen; Gao, Meng; Ren, Ying; Lou, Ruyun; Xie, Hongguo; Yu, Weiting; Liu, Xiudong; Ma, Xiaojun

    2016-08-03

    The surface properties of implanted materials or devices play critical roles in modulating cell behavior. However, the surface properties usually affect cell behaviors synergetically so that it is still difficult to separately investigate the influence of a single property on cell behavior in practical applications. In this study, alginate-chitosan (AC) microcapsules with a dense or loose gel structure were fabricated to understand the effect of gel structure on cell behavior. Cells preferentially adhered and spread on the loose gel structure microcapsules rather than on the dense ones. The two types of microcapsules exhibited nearly identical surface positive charges, roughness, stiffness, and hydrophilicity; thus, the result suggested that the gel structure was the principal factor affecting cell behavior. X-ray photoelectron spectroscopy analyses demonstrated that the overall percentage of positively charged amino groups was similar on both microcapsules. The different gel structures led to different states and distributions of the positively charged amino groups of chitosan, so we conclude that the loose gel structure facilitated greater cell adhesion and spreading mainly because more protonated amino groups remained unbound and exposed on the surface of these microcapsules.

  6. Salt-assisted and salt-suppressed sol-gel transitions of methylcellulose in water.

    Science.gov (United States)

    Xu, Y; Wang, C; Tam, K C; Li, L

    2004-02-03

    The effects of various salts on the sol-gel transition of aqueous methylcellulose (MC) solutions have been studied systematically by means of a micro differential scanning calorimeter. It was found that the heating process was endothermic while the cooling process was exothermic for both MC solutions with and without salts. The addition of salts did not change the patterns of gelation and degelation of MC. However, the salts could shift the sol-gel transition and the gel-sol transition to lower or higher temperatures from a pure MC solution, depending on the salt type. These opposite effects were termed the salt-assisted and salt-suppressed sol-gel transitions. Either the salt-assisted transition or the salt-suppressed sol-gel transition was a function of salt concentration. In addition, each salt was found to have its own concentration limit for producing a stable aqueous solution of MC at a given concentration of MC, which was related to the anionic charge density of the salt. Cations were proved to have weaker effects than anions. The "salt-out strength", defined as the salt effect per mole of anion, was obtained for each anion studied. The thermodynamic mechanisms involved in the salt-assisted and salt-suppressed sol-gel transitions are discussed.

  7. Silica- and germania-based dual-ligand sol-gel organic-inorganic hybrid sorbents combining superhydrophobicity and π-π interaction. The role of inorganic substrate in sol-gel capillary microextraction.

    Science.gov (United States)

    Seyyal, Emre; Malik, Abdul

    2017-04-29

    Principles of sol-gel chemistry were utilized to create silica- and germania-based dual-ligand surface-bonded sol-gel coatings providing enhanced performance in capillary microextraction (CME) through a combination of ligand superhydrophobicity and π-π interaction. These organic-inorganic hybrid coatings were prepared using sol-gel precursors with bonded perfluorododecyl (PF-C 12 ) and phenethyl (PhE) ligands. Here, the ability of the PF-C 12 ligand to provide enhanced hydrophobic interaction was advantageously combined with π-π interaction capability of the PhE moiety to attain the desired sorbent performance in CME. The effect of the inorganic sorbent component on microextraction performance of was explored by comparing microextraction characteristics of silica- and germania-based sol-gel sorbents. The germania-based dual-ligand sol-gel sorbent demonstrated superior CME performance compared to its silica-based counterpart. Thermogravimetric analysis (TGA) of the created silica- and germania-based dual-ligand sol-gel sorbents suggested higher carbon loading on the germania-based sorbent. This might be indicative of more effective condensation of the organic ligand-bearing sol-gel-active chemical species to the germania-based sol-gel network (than to its silica-based counterpart) evolving in the sol solution. The type and concentration of the organic ligands were varied in the sol-gel sorbents to fine-tune extraction selectivity toward different classes of analytes. Specific extraction (SE) values were used for an objective comparison of the prepared sol-gel CME sorbents. The sorbents with higher content of PF-C 12 showed remarkable affinity for aliphatic hydrocarbons. Compared to their single-ligand sol-gel counterparts, the dual-ligand sol-gel coatings demonstrated significantly superior CME performance in the extraction of alkylbenzenes, providing up to ∼65.0% higher SE values. The prepared sol-gel CME coatings provided low ng L -1 limit of detections (LOD

  8. Evolution of gel structure during thermal processing of Na-geopolymer gels.

    Science.gov (United States)

    Duxson, Peter; Lukey, Grant C; van Deventer, Jannie S J

    2006-10-10

    The present work examines how the gel structure and phase composition of Na-geopolymers derived from metakaolin with varied Si/Al ratio evolve with exposure to temperatures up to 1000 degrees C. Gels were thermally treated and characterized using quantitative XRD, DTA, and FTIR to elucidate the changes in gel structure, phase composition, and porosity at each stage of heating. It is found that the phase stability, defined by the amount and onset temperature of crystallization, is improved at higher Si/Al ratios. Two different mechanisms of densification have been isolated by FTIR, related to viscous flow and collapse of the highly distributed pore network in the gel. Gels with low Si/Al ratio only experience viscous flow that correlates with low thermal shrinkage. Gels at a higher Si/Al ratio, which have a homogeneous microstructure composed of a highly distributed porosity, undergo both densification processes corresponding to a large extent of thermal shrinkage during densification. This work elucidates the intimate relationship between gel microstructure, chemistry, and thermal evolution of Na-geopolymer gels.

  9. Assessment of Anti HSV-1 Activity of Aloe Vera Gel Extract: an In Vitro Study

    Science.gov (United States)

    Rezazadeh, Fahimeh; Moshaverinia, Maryam; Motamedifar, Mohammad; Alyaseri, Montazer

    2016-01-01

    Statement of the Problem Herpes simplex virus (HSV) infection is one of the most common and debilitating oral diseases; yet, there is no standard topical treatment to control it. The extract of Aloe vera leaves has been previously reported to have anti-inflammatory, antibacterial, and also antiviral effects. There is no data on anti-Herpes simplex virus type 1 (HSV-1) activity of Aloe vera gel. Purpose This study aimed to evaluate the anti-HSV-1 activity of Aloe vera gel in Vero cell line. Materials and Method In this study, gel extraction and cytotoxicity of various increasing concentrations of Aloe vera gel (0.2, 0.5, 1, 2, and 5%) was evaluated in Dulbecco’s Modified Eagle Medium (DMEM) containing 2% fetal bovine serum (FBS). Having been washed with phosphate buffered saline, 50 plaque-forming units (PFU) of HSV-1 was added to each well. After 1 hour of incubation at 37°C, cell monolayers in 24 well plates were exposed to different increasing concentrations of Aloe vera gel. The anti-HSV-1 activity of Aloe vera gel in different concentrations was assessed by plaque reduction assays. Data were analyzed by using One-way ANOVA. Results The cytotoxicity assay showed that Aloe vera in prearranged concentrations was cell-compatible. The inhibitory effect of various concentrations of Aloe vera was observed one hour after the Vero cell was infected with HSV-1. However, there was no significant difference between two serial concentrations (p> 0.05). One-way ANOVA also revealed no significant difference between the groups. The findings indicated a dose-dependent antiviral effect of Aloe vera. Conclusion The findings showed significant inhibitory effect of 0.2-5% Aloe vera gel on HSV-1 growth in Vero cell line. Therefore, this gel could be a useful topical treatment for oral HSV-1 infections without any significant toxicity. PMID:26966709

  10. Assessment of Anti HSV-1 Activity of Aloe Vera Gel Extract: an In Vitro Study.

    Science.gov (United States)

    Rezazadeh, Fahimeh; Moshaverinia, Maryam; Motamedifar, Mohammad; Alyaseri, Montazer

    2016-03-01

    Herpes simplex virus (HSV) infection is one of the most common and debilitating oral diseases; yet, there is no standard topical treatment to control it. The extract of Aloe vera leaves has been previously reported to have anti-inflammatory, antibacterial, and also antiviral effects. There is no data on anti-Herpes simplex virus type 1 (HSV-1) activity of Aloe vera gel. This study aimed to evaluate the anti-HSV-1 activity of Aloe vera gel in Vero cell line. In this study, gel extraction and cytotoxicity of various increasing concentrations of Aloe vera gel (0.2, 0.5, 1, 2, and 5%) was evaluated in Dulbecco's Modified Eagle Medium (DMEM) containing 2% fetal bovine serum (FBS). Having been washed with phosphate buffered saline, 50 plaque-forming units (PFU) of HSV-1 was added to each well. After 1 hour of incubation at 37°C, cell monolayers in 24 well plates were exposed to different increasing concentrations of Aloe vera gel. The anti-HSV-1 activity of Aloe vera gel in different concentrations was assessed by plaque reduction assays. Data were analyzed by using One-way ANOVA. The cytotoxicity assay showed that Aloe vera in prearranged concentrations was cell-compatible. The inhibitory effect of various concentrations of Aloe vera was observed one hour after the Vero cell was infected with HSV-1. However, there was no significant difference between two serial concentrations (p> 0.05). One-way ANOVA also revealed no significant difference between the groups. The findings indicated a dose-dependent antiviral effect of Aloe vera. The findings showed significant inhibitory effect of 0.2-5% Aloe vera gel on HSV-1 growth in Vero cell line. Therefore, this gel could be a useful topical treatment for oral HSV-1 infections without any significant toxicity.

  11. Physical and chemical properties of gels. Application to protein nucleation control in the gel acupuncture technique

    Science.gov (United States)

    Moreno, Abel; Juárez-Martínez, Gabriela; Hernández-Pérez, Tomás; Batina, Nikola; Mundo, Manuel; McPherson, Alexander

    1999-09-01

    In this work, we present a new approach using analytical and optical techniques in order to determine the physical and chemical properties of silica gel, as well as the measurement of the pore size in the network of the gel by scanning electron microscopy. The gel acupuncture technique developed by García-Ruiz et al. (Mater. Res. Bull 28 (1993) 541) García-Ruiz and Moreno (Acta Crystallogr. D 50 (1994) 484) was used throughout the history of crystal growth. Several experiments were done in order to evaluate the nucleation control of model proteins (thaumatin I from Thaumatococcus daniellii, lysozyme from hen egg white and catalase from bovine liver) by the porous network of the gel. Finally, it is shown how the number and the size of the crystals obtained inside X-ray capillaries is controlled by the size of the porous structure of the gel.

  12. Mucosal effects of tenofovir 1% gel.

    Science.gov (United States)

    Hladik, Florian; Burgener, Adam; Ballweber, Lamar; Gottardo, Raphael; Vojtech, Lucia; Fourati, Slim; Dai, James Y; Cameron, Mark J; Strobl, Johanna; Hughes, Sean M; Hoesley, Craig; Andrew, Philip; Johnson, Sherri; Piper, Jeanna; Friend, David R; Ball, T Blake; Cranston, Ross D; Mayer, Kenneth H; McElrath, M Juliana; McGowan, Ian

    2015-02-03

    Tenofovir gel is being evaluated for vaginal and rectal pre-exposure prophylaxis against HIV transmission. Because this is a new prevention strategy, we broadly assessed its effects on the mucosa. In MTN-007, a phase-1, randomized, double-blinded rectal microbicide trial, we used systems genomics/proteomics to determine the effect of tenofovir 1% gel, nonoxynol-9 2% gel, placebo gel or no treatment on rectal biopsies (15 subjects/arm). We also treated primary vaginal epithelial cells from four healthy women with tenofovir in vitro. After seven days of administration, tenofovir 1% gel had broad-ranging effects on the rectal mucosa, which were more pronounced than, but different from, those of the detergent nonoxynol-9. Tenofovir suppressed anti-inflammatory mediators, increased T cell densities, caused mitochondrial dysfunction, altered regulatory pathways of cell differentiation and survival, and stimulated epithelial cell proliferation. The breadth of mucosal changes induced by tenofovir indicates that its safety over longer-term topical use should be carefully monitored.

  13. Comparative Two-Dimensional Fluorescence Gel Electrophoresis.

    Science.gov (United States)

    Ackermann, Doreen; König, Simone

    2018-01-01

    Two-dimensional comparative fluorescence gel electrophoresis (CoFGE) uses an internal standard to increase the reproducibility of coordinate assignment for protein spots visualized on 2D polyacrylamide gels. This is particularly important for samples, which need to be compared without the availability of replicates and thus cannot be studied using differential gel electrophoresis (DIGE). CoFGE corrects for gel-to-gel variability by co-running with the sample proteome a standardized marker grid of 80-100 nodes, which is formed by a set of purified proteins. Differentiation of reference and analyte is possible by the use of two fluorescent dyes. Variations in the y-dimension (molecular weight) are corrected by the marker grid. For the optional control of the x-dimension (pI), azo dyes can be used. Experiments are possible in both vertical and horizontal (h) electrophoresis devices, but hCoFGE is much easier to perform. For data analysis, commercial software capable of warping can be adapted.

  14. DNA DAMAGE QUANTITATION BY ALKALINE GEL ELECTROPHORESIS.

    Energy Technology Data Exchange (ETDEWEB)

    SUTHERLAND,B.M.; BENNETT,P.V.; SUTHERLAND, J.C.

    2004-03-24

    Physical and chemical agents in the environment, those used in clinical applications, or encountered during recreational exposures to sunlight, induce damages in DNA. Understanding the biological impact of these agents requires quantitation of the levels of such damages in laboratory test systems as well as in field or clinical samples. Alkaline gel electrophoresis provides a sensitive (down to {approx} a few lesions/5Mb), rapid method of direct quantitation of a wide variety of DNA damages in nanogram quantities of non-radioactive DNAs from laboratory, field, or clinical specimens, including higher plants and animals. This method stems from velocity sedimentation studies of DNA populations, and from the simple methods of agarose gel electrophoresis. Our laboratories have developed quantitative agarose gel methods, analytical descriptions of DNA migration during electrophoresis on agarose gels (1-6), and electronic imaging for accurate determinations of DNA mass (7-9). Although all these components improve sensitivity and throughput of large numbers of samples (7,8,10), a simple version using only standard molecular biology equipment allows routine analysis of DNA damages at moderate frequencies. We present here a description of the methods, as well as a brief description of the underlying principles, required for a simplified approach to quantitation of DNA damages by alkaline gel electrophoresis.

  15. Synthetic PAMPS gel activates BMP/Smad signaling pathway in ATDC5 cells, which plays a significant role in the gel-induced chondrogenic differentiation.

    Science.gov (United States)

    Goto, Keiko; Kimura, Taichi; Kitamura, Nobuto; Semba, Shingo; Ohmiya, Yoshihiro; Aburatani, Sachiyo; Matsukura, Satoko; Tsuda, Masumi; Kurokawa, Takayuki; Ping Gong, Jian; Tanaka, Shinya; Yasuda, Kazunori

    2016-03-01

    The purposes of this study were to identify signaling pathways that were specifically activated in ATDC5 cells cultured on poly (2-acrylamido-2-methylpropanesulfonic acid) (PAMPS) gel in insulin-free maintenance medium and to evaluate the significance of the determined signaling pathways in the chondrogenic differentiation induced by this gel. In this study, ATDC5 cells cultured on PAMPS gel using the maintenance medium without insulin (PAMPS Culture) were compared with cells cultured on polystyrene using the differentiation medium containing insulin (PS-I Culture). The microarray analysis, Western blot analysis, and real-time PCR analysis demonstrated that the TGF-β/BMP signaling pathway was significantly enhanced at Days 1, 2, and 3 in the PAMPS Culture when compared with the PS-I Culture. Inhibition of the BMP type-I receptor reduced the phosphorylation level of Smad1/5 and expression of type-2 collagen and aggrecan mRNA in the cells accompanied by a reduction in cell aggregation at Day 13 in the PAMPS Culture. The inhibition of the TGF-β/BMP signaling pathway significantly inhibited the chondrogenic differentiation induced by the PAMPS gel. The present study demonstrated that synthetic PAMPS gel activates the TGF-β/BMP/Smad signaling pathway in the ATDC5 cells in the absence of insulin, and that this activation plays a significant role in the chondrogenic differentiation induced by PAMPS gel. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 734-746, 2016. © 2015 Wiley Periodicals, Inc.

  16. Recubrimientos de hidroxiapatita preparados mediante un proceso sol-gel

    Directory of Open Access Journals (Sweden)

    Peón, E.

    2005-12-01

    Full Text Available Hydroxyapatite coatings (HAp have been obtained starting from precursors of sol-gel type. The coatings previously oxidized were deposited on metal surfaces of a based on iron alloy so-called MA956. The alloys were at high temperatures, in order to improve the adhesion with the hydroxyapatite coatings. The sol-gel coating was obtained applying an aqueous route, using triethyl phosphite and aqueous calcium nitrate, as precursors of phosphorous and calcium, respectively. Different sintering thermal treatments were applied on the resulting gels in order to obtain a homogeneous, adherent and crystalline hydroxyapatite coating. The characterization techniques used for this study were optical microscopy, SEM/EDX, XDR and FTIR. Moreover, the adhesion between the hydroxylapatite coating and the substrate was assessed according to the ASTM D 3359-02 standard test method. The results of this study showed that the best thermal treatment is obtained for a sintering temperature of 550 °C during a time of 72 h.

    Se han preparado nuevos recubrimientos de hidroxiapatita (HAp obtenidos a partir de precursores de tipo sol-gel, depositados sobre sustratos metálicos de una aleación de base hierro denominada MA956, previamente oxidados a elevadas temperaturas, para mejorar la adherencia con los recubrimientos de hidroxiapatita. El recubrimiento sol-gel se obtuvo aplicando una ruta acuosa, utilizando como precursores del fósforo y del calcio trietilfosfito y nitrato cálcico tetrahidratado, respectivamente. Sobre los geles resultantes se aplicaron distintos tratamientos térmicos de sinterización, hasta la obtención de recubrimientos de hidroxiapatita homogéneos, adherentes y cristalinos. Las técnicas de caracterización utilizadas para realizar este estudio han sido microscopía óptica, MBE/EDX, DRX y FTIR. Así mismo, se ha determinado la adherencia entre el substrato y el recubrimiento de hidroxiapatita según la norma ASTM D 3359-02. Los resultados

  17. Automatic DNA Diagnosis for 1D Gel Electrophoresis Images using Bio-image Processing Technique.

    Science.gov (United States)

    Intarapanich, Apichart; Kaewkamnerd, Saowaluck; Shaw, Philip J; Ukosakit, Kittipat; Tragoonrung, Somvong; Tongsima, Sissades

    2015-01-01

    DNA gel electrophoresis is a molecular biology technique for separating different sizes of DNA fragments. Applications of DNA gel electrophoresis include DNA fingerprinting (genetic diagnosis), size estimation of DNA, and DNA separation for Southern blotting. Accurate interpretation of DNA banding patterns from electrophoretic images can be laborious and error prone when a large number of bands are interrogated manually. Although many bio-imaging techniques have been proposed, none of them can fully automate the typing of DNA owing to the complexities of migration patterns typically obtained. We developed an image-processing tool that automatically calls genotypes from DNA gel electrophoresis images. The image processing workflow comprises three main steps: 1) lane segmentation, 2) extraction of DNA bands and 3) band genotyping classification. The tool was originally intended to facilitate large-scale genotyping analysis of sugarcane cultivars. We tested the proposed tool on 10 gel images (433 cultivars) obtained from polyacrylamide gel electrophoresis (PAGE) of PCR amplicons for detecting intron length polymorphisms (ILP) on one locus of the sugarcanes. These gel images demonstrated many challenges in automated lane/band segmentation in image processing including lane distortion, band deformity, high degree of noise in the background, and bands that are very close together (doublets). Using the proposed bio-imaging workflow, lanes and DNA bands contained within are properly segmented, even for adjacent bands with aberrant migration that cannot be separated by conventional techniques. The software, called GELect, automatically performs genotype calling on each lane by comparing with an all-banding reference, which was created by clustering the existing bands into the non-redundant set of reference bands. The automated genotype calling results were verified by independent manual typing by molecular biologists. This work presents an automated genotyping tool from DNA

  18. Automatic DNA Diagnosis for 1D Gel Electrophoresis Images using Bio-image Processing Technique

    Science.gov (United States)

    2015-01-01

    Background DNA gel electrophoresis is a molecular biology technique for separating different sizes of DNA fragments. Applications of DNA gel electrophoresis include DNA fingerprinting (genetic diagnosis), size estimation of DNA, and DNA separation for Southern blotting. Accurate interpretation of DNA banding patterns from electrophoretic images can be laborious and error prone when a large number of bands are interrogated manually. Although many bio-imaging techniques have been proposed, none of them can fully automate the typing of DNA owing to the complexities of migration patterns typically obtained. Results We developed an image-processing tool that automatically calls genotypes from DNA gel electrophoresis images. The image processing workflow comprises three main steps: 1) lane segmentation, 2) extraction of DNA bands and 3) band genotyping classification. The tool was originally intended to facilitate large-scale genotyping analysis of sugarcane cultivars. We tested the proposed tool on 10 gel images (433 cultivars) obtained from polyacrylamide gel electrophoresis (PAGE) of PCR amplicons for detecting intron length polymorphisms (ILP) on one locus of the sugarcanes. These gel images demonstrated many challenges in automated lane/band segmentation in image processing including lane distortion, band deformity, high degree of noise in the background, and bands that are very close together (doublets). Using the proposed bio-imaging workflow, lanes and DNA bands contained within are properly segmented, even for adjacent bands with aberrant migration that cannot be separated by conventional techniques. The software, called GELect, automatically performs genotype calling on each lane by comparing with an all-banding reference, which was created by clustering the existing bands into the non-redundant set of reference bands. The automated genotype calling results were verified by independent manual typing by molecular biologists. Conclusions This work presents an

  19. Study of the performance of gels of molybdenum containing several cations for the preparation of 99Mo and 99mTc

    International Nuclear Information System (INIS)

    Moraes, Vanessa

    2005-01-01

    99m Tc is the most employed radioisotope in Nuclear Medicine, due to its nuclear characteristics: short half-life (6.04 h); emission of low energy gamma ray (140 keV); no emission of β - ; generated by the radioactive decay of 99 Mo (radioisotope generator system). 99 Mo can be produced in cyclotron or nuclear reactor by the irradiation of 235 U (n, f) 99 Mo or by the 98 Mo (n, γ) 90 Mo reaction. Four different kinds of generators of 99m Tc can be employed, based on the separation techniques: column chromatographic using alumina, with fission 99 Mo; solvent extraction using methylethylketone; sublimation of technetium heptoxide; gel type chromatographic generator, that contains molybdenum. IPEN, aiming the nationalization of the 99m Tc generators production, developed a gel type generator that uses zirconium molybdate. Three types of gels are studied in the work: molybdenum gel with titanium, molybdenum gel with cerium and molybdenum gel with hafnium, that were compared with the molybdenum gel with zirconium. The variables studied in the gel preparation are: mass relation between Mo and the cation, NaOH concentration, temperature and final pH of the product. After the preparation, the gels are analysed in relation to the amount of Mo and the cation, structure and gel particle size. The gel is irradiated and later a generator system is prepared, and the elutions are analysed in order to measure the 99m Tc elution efficiency. The results showed that the molybdenum gel with titanium had the best performance in all analysis. (author)

  20. Elasticity and clustering in concentrated depletion gels.

    Science.gov (United States)

    Ramakrishnan, S; Chen, Y-L; Schweizer, K S; Zukoski, C F

    2004-10-01

    X-ray scattering and rheology are employed to study the volume fraction dependence of the collective structure and elastic moduli of concentrated nanoparticle-polymer depletion gels. The nonequilibrium gel structure consists of locally densified nonfractal clusters and narrow random interfaces. The elastic moduli display a power law dependence on volume fraction with effective exponents that decrease with increasing depletion attraction strength. A microscopic theory that combines local structural information with a dynamic treatment of gelation is in good agreement with the observations.

  1. Pouring and running a protein gel by reusing commercial cassettes.

    Science.gov (United States)

    Hwang, Alexander C; Grey, Paris H; Cuddy, Katrina; Oppenheimer, David G

    2012-02-12

    The evaluation of proteins using sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) analysis is a common technique used by biochemistry and molecular biology researchers. For laboratories that perform daily analyses of proteins, the cost of commercially available polyacrylamide gels (~$10/gel) can be considerable over time. To mitigate this cost, some researchers prepare their own polyacrylamide gels. Traditional methods of pouring these gels typically utilize specialized equipment and glass gel plates that can be expensive and preclude pouring many gels and storing them for future use. Furthermore, handling of glass plates during cleaning or gel pouring can result in accidental breakage creating a safety hazard, which may preclude their use in undergraduate laboratory classes. Our protocol demonstrates how to pour multiple protein gels simultaneously by recycling Invitrogen Nupage Novex minigel cassettes, and inexpensive materials purchased at a home improvement store. This economical and streamlined method includes a way to store the gels at 4°C for a few weeks. By re-using the plastic gel cassettes from commercially available gels, labs that run frequent protein gels can save significant costs and help the environment. In addition, plastic gel cassettes are extremely resistant to breakage, which makes them ideal for undergraduate laboratory classrooms.

  2. Hydrogen gas evolution from water in zeolite and silica gel cavities with γ-ray irradiation

    International Nuclear Information System (INIS)

    Maeda, Y.; Kawamura, K.; Hayama, Y.; Okai, T.

    2002-01-01

    Hydrogen gas evolution from water in zeolite cavities caused by gamma irradiation was examined. Metal oxides prepared in the cavities of Y-type zeolites and silica gels were also used for this examination. The G-values for hydrogen gas evolution of water in the cavity were higher than those of pure water. The mechanism of water decomposition by the effect of gamma irradiation was studied and clarified to an extent. It is supposed that hydrogen gas evolution is increased if the H radicals can mutually combine. The interfering reactions for hydrogen gas evolution would the existence of electrons and OH radicals, and the recombination reactions. The size of a spur in which the reaction of gamma-rays with the metal oxides takes place is assumed to be about 3 nm. ZSM-5 zeolites, Y-type zeolites, and silica gels were used, the size of the cavities was 3, 5 and 7 nm. The wet zeolites, silica gels and those containing the metal oxides were irradiated with 37.4-78.8 KGy of 60 Co under nitrogen. The evolving hydrogen gas was determined by gas chromatography. From among the samples examined, silica gel A exhibited the highest yield. Although the reasons for these results are not clear, it s evident that the surface of the zeolites and silica gels plays an important role with respect to the radicals produced by the action of gamma radiation

  3. Potential use of gradient denaturing gel electrophoresis in obtaining mutational spectra from human cells

    International Nuclear Information System (INIS)

    Thilly, W.G.

    1985-01-01

    A method is described to isolate mutations in DNA in human cells. When a double-stranded DNA migrates through an electric field on an electrophoretic gel, it is compact hydrodynamic structure relative to the same material in a melted form. Normally the solution in electrophoretic gels is uniform, but a way has been devised to set up a stable gradient of increasing solute concentration in the direction of DNA motion. Thus, as a double-stranded DNA molecule is drawn by the electric field into higher and higher concentrations of urea/formamide, it will eventually reach a point at which the concentration is high enough to melt the lower-melting-point region. The melting results in an essentially immobile structure within the gel so that the position at which the DNA molecule stops on the gradient gel is determined by its melting point, which is uniquely determined by its nucleotide sequence. A single base pair substitution within a low melting point sequence of some 100 base pairs changed the expected melting point by 0.4 0 C and resulted in about a 2-cm displacement under appropriate denaturing gel conditions. This expectation leads to the idea that if a mixture of DNA sequences derived from point mutations within the same restriction fragment were permitted to anneal with a complementary wild-type sequence, the melting point of each type of heteroduplex would differ depending on the kind and position of each mutation

  4. Eliminating blurry bands in gels with a simple cost-effective repair to the gel cassette.

    Science.gov (United States)

    Bingaman, Jamie L; Frankel, Erica A; Hull, Chelsea M; Leamy, Kathleen A; Messina, Kyle J; Mitchell, David; Park, Hongmarn; Ritchey, Laura E; Babitzke, Paul; Bevilacqua, Philip C

    2016-12-01

    Gel electrophoresis and subsequent imaging using phosphorimagers is one of the most important and widely used techniques in RNA and DNA analysis. Radiolabeling nucleic acids with 32 P and detecting bands using a phoshorimager are useful both in a qualitative sense for nucleic acid detection and in a quantitative sense for structural, kinetic, or binding-based assays. Because of this, good resolution of gel bands based on molecular weight and size of RNA or DNA is essential for analysis. The appearance of blurry gel bands of 32 P-labeled RNA and DNA thus represents a serious problem in the laboratory. A quick search on the Internet uncovers numerous reports begrudging the appearance of blurry bands, as well as attempts to fix them without success. Indeed, our laboratories were beset by the intermittent problem of blurry gels for over one year before we found a solution. Herein we describe a simple and cost-effective solution to a problem that we show originates from the phosphorimager cassettes rather than the integrity of the gel itself. We hope that the information provided here will lead to immediate help for other laboratories experiencing similar issues with labeled nucleic acid gel-based assays. The improvement in the clarity of the gels is nothing short of astonishing in many instances and will lead to higher resolution images for analysis and publications. © 2016 Bingaman et al.; Published by Cold Spring Harbor Laboratory Press for the RNA Society.

  5. Species identification of cooked fish by urea isoelectric focusing and sodium dodecylsulfate polyacrylamide gel electrophoresis : a collaborative study

    DEFF Research Database (Denmark)

    Rehbein, H.; Kundiger, R.; Yman, I.M.

    1999-01-01

    The suitability and reliability of urea IEF and SDS-PAGE for the identification of cooked fish flesh was tested by a collaborative study among nine laboratories. Urea IEF was performed with CleanGels as well as with ImmobilineGels, and ExcelGels were used for SDS-PAGE, enabling all three types...... was incorrect, and with SDS-PAGE a similar result was obtained. It was concluded that methods, as now developed, are suitable for checking the species declaration of fishery products. (C) 1999 Elsevier Science Ltd. All rights reserved...

  6. Tough Amphiphilic Gels for Antifouling Applications

    Science.gov (United States)

    Villada, Laura M.

    Biofouling is the attachment of unwanted organisms on a surface, and it is influenced by a host of variables including the chemistry of the material as well as both the surface and bulk properties, and controlling and understanding the effect of these properties is critical for the development of effective materials to combat biofouling. All surfaces that are submerged in water are subject to the rapid colonization of a wide range of marine organisms. Marine biofouling decreases fuel efficiency, costing the Navy millions of dollars in penalty, as well as having drastic environmental effects. Previous prevention of biofouling in marine systems has been accomplished by the administration of biocides and toxic coatings. In recent years, increased concerns about the impacts of these hazardous compounds into marine ecosystems has spurred efforts to develop cost effective, non-toxic, and durable anti-fouling coatings. Hydrogels, hydrophilic crosslinked networks, are being used to modify silicone marine coatings and have demonstrated potential at combatting biofouling. Understanding the impact of amphiphilic materials, i.e. their structure and properties, on biofouling is of great importance in order to address the need in the industry. In this study, poly(2-hydroxyethyl methacrylate) (HEMA) crosslinked networks were tailored to investigate the influence of their surface and bulk properties on biofouling. Previous research utilizing HEMA-siloxane gels suggested a relationship between molecular weight between crosslinks, M c, and the attachment of soft fouling sporelings of the green algae U. linza and adsorption of the protein bovine serum albumin (BSA), and the initial thrust of this dissertation was aimed at resolving this relationship. Gel composition was modified by varying the siloxane crosslinking agent and the siloxane hydrophobic monomer concentrations. The gels exhibited an increase in elastic modulus from 0.17 to 8.55 MPa that coincided with an increasing

  7. Normoxic polymer gel - basic characterisation and clinical use

    International Nuclear Information System (INIS)

    Scheib, S G; Vogelsanger, W; Gianolini, S; Crescenti, R

    2004-01-01

    The formulation for a new polymer gel, which is made under normal atmospheric conditions, has been published. Because manufacturing and processing can be performed under normal atmospheric conditions, the gel is also called normoxic. Only a few accessories for gel production are necessary, facilitating the use of this gel, which can be easily produced in a clinical environment. The purpose of this study, which is work in progress, was to produce several gel batches with varying concentrations of their compounds, to measure dose response curves, to investigate ageing effects and to use this polymer gel in 3D absolute dose verifications in radiosurgery, IMRT and proton therapy

  8. Multiple-phase behavior and memory effect of polymer gel

    CERN Document Server

    Annaka, M; Nakahira, T; Sugiyama, M; Hara, K; Matsuura, T

    2002-01-01

    A poly(4-acrylamidosalicylic acid) gel (PASA gel) exhibits multiple phases as characterized by distinct degrees of swelling; the gel can take one of four different swelling values, but none of the intermediate values. The gel has remarkable memory: the phase behavior of the gel depends on whether the gel has experienced the most swollen phase or the most collapsed phase in the immediate past. The information is stored and reversibly erased in the form of a macroscopic phase transition behavior. The structure factors corresponding to these four phases were obtained by SANS, which indicated the presence of characteristic structures depending on pH and temperature, particularly in the shrunken state. (orig.)

  9. Protein electrophoretic migration data from custom and commercial gradient gels

    Directory of Open Access Journals (Sweden)

    Andrew J. Miller

    2016-12-01

    Full Text Available This paper presents data related to the article “A method for easily customizable gradient gel electrophoresis” (A.J. Miller, B. Roman, E.M. Norstrom, 2016 [1]. Data is presented on the rate of electrophoretic migration of proteins in both hand-poured and commercially acquired acrylamide gradient gels. For each gel, migration of 9 polypeptides of various masses was measured upon completion of gel electrophoresis. Data are presented on the migration of proteins within separate lanes of the same gel as well as migration rates from multiple gels.

  10. The mechanism and properties of acid-coagulated milk gels

    Directory of Open Access Journals (Sweden)

    Chanokphat Phadungath

    2005-03-01

    Full Text Available Acid-coagulated milk products such as fresh acid-coagulated cheese varieties and yogurt areimportant dairy food products. However, little is known regarding the mechanisms involved in gel formation, physical properties of acid gels, and the effects of processing variables such as heat treatment and gelation temperature on the important physical properties of acid milk gels. This paper reviews the modern concepts of possible mechanisms involved in the formation of particle milk gel aggregation, along with recent developments including the use of techniques such as dynamic low amplitude oscillatory rheology to observe the gel formation process, and confocal laser scanning microscopy to monitor gel microstructure.

  11. Initial investigation of a novel light-scattering gel phantom for evaluation of optical CT scanners for radiotherapy gel dosimetry

    International Nuclear Information System (INIS)

    Bosi, Stephen; Naseri, Pourandokht; Puran, Alicia; Davies, Justin; Baldock, Clive

    2007-01-01

    There is a need for stable gel materials for phantoms used to validate optical computerized tomography (CT) scanners used in conjunction with radiation-induced polymerizing gel dosimeters. Phantoms based on addition of light-absorbing dyes to gelatine to simulate gel dosimeters have been employed. However, to more accurately simulate polymerizing gels one requires phantoms that employ light-scattering colloidal suspensions added to the gel. In this paper, we present the initial results of using an optical CT scanner to evaluate a novel phantom in which radiation-exposed polymer gels are simulated by the addition of colloidal suspensions of varying turbidity. The phantom may be useful as a calibration transfer standard for polymer gel dosimeters. The tests reveal some phenomena peculiar to light-scattering gels that need to be taken into account when calibrating polymer gel dosimeters

  12. SAXS study of silica sols, gels and glasses obtained by the sol gel process

    International Nuclear Information System (INIS)

    Santos, D.I. dos; Aegerter, M.A.

    1988-01-01

    Systematic SAXS studies have been performed at the LURE Synchrotron, Orsay, using an intense beam of point like cross-section to obtain information about the sol -> humid gel -> dried gel -> silica glass transformation. The intensity curves have been analysed in term of power law in log-log plots, whose exponent is related to mass and surface fractal dimensions of the structure. It was found that almost all phases present fractal structures and for the case of basic gels, is of hierarchical nature. The aerogels are formed by a dense matrix, with a smooth surface and exhibit a very narrow auto-similarity range that gives a mass fractal dimension. (author) [pt

  13. Formation, Clearance and Mouthfeel Perception of Oral Coatings Formed by Emulsion-Filled Gels

    NARCIS (Netherlands)

    Camacho, Sara; Liu, Kun; Linden, Van Der Anoek; Stieger, Markus; De Velde, Van Fred

    2015-01-01

    Four emulsion-filled gelatin gels varying in fat content (5 and 15%) and type of emulsifier (whey protein isolate: fat droplets bound to matrix; Tween 20: fat droplets unbound to matrix) were studied. We investigated (1) the formation and clearance dynamics of fat deposition on the tongue using in

  14. Reversible gel-sol photoswitching with an overcrowded alkene-based bis-urea supergelator

    NARCIS (Netherlands)

    Wezenberg, Sander J.; Croisetu, Christelle M.; Stuart, Marc C. A.; Feringa, Ben L.

    2016-01-01

    A new type of low-molecular-weight gelator (LMWG), i.e. overcrowded alkene-based bis-ureas, can be switched effectively between cis and trans isomers using light as demonstrated by H-1 NMR and UV-Vis spectroscopy. Gelation studies reveal that one of the synthesized trans compounds forms stable gels

  15. KEKUATAN GEL GELATIN TIPE B DALAM FORMULASI GRANUL TERHADAP KEMAMPUAN MUKOADHESIF

    Directory of Open Access Journals (Sweden)

    Astri Fajriani

    2009-06-01

    Full Text Available Type B Gelatin Gel Strength in Granule Formulation and its Mucoadhesive Characteristics. Mucoadhesive test of polymer excipient is important for development of oral sustained release dosage form in mucoadhesive system to increase bioavailability of a drug. The study focused on mucoadhesive strength of gelatinus granules in stomach and intestine of rat using bioadhesive and wash off tests. Gelatin is a substance obtained from partially hydrolyzed collagen of skin, white cattle bones and animal bones. Gelatin derived from acid process is called type A gelatin and those from alkali process is called type B gelatin. This research studied the influence of various gel strength of type B gelatins, particularly their mucoadhesive characteristics. Mucoadhesive tests were performed at the concentration of 7.14%, 3.66%, and 2.45% and with gel strength of 328 g Bloom, 230 g Bloom and 119 g Bloom respectively. The results showed that granules formula with 230 g Bloom gel strength showed the best mucoadhesive strength, with adhesion percentage of 100%.

  16. Study of silica sol-gel materials for sensor development

    Science.gov (United States)

    Lei, Qiong

    Silica sol-gel is a transparent, highly porous silicon oxide glass made at room temperature by sol-gel process. The name of silica sol-gel comes from the observable physical phase transition from liquid sol to solid gel during its preparation. Silica sol-gel is chemically inert, thermally stable, and photostable, it can be fabricated into different desired shapes during or after gelation, and its porous structure allows encapsulation of guest molecules either before or after gelation while still retaining their functions and sensitivities to surrounding environments. All those distinctive features make silica sol-gel ideal for sensor development. Study of guest-host interactions in silica sol-gel is important for silica-based sensor development, because it helps to tailor local environments inside sol-gel matrix so that higher guest loading, longer shelf-life, higher sensitivity and faster response of silica gel based sensors could be achieved. We focused on pore surface modification of two different types of silica sol-gel by post-grafting method, and construction of stable silica hydrogel-like thin films for sensor development. By monitoring the mobility and photostability of rhodamine 6G (R6G) molecules in silica alcogel thin films through single molecule spectroscopy (SMS), the guest-host interactions altered by post-synthesis grafting were examined. While physical confinement remains the major factor that controls mobility in modified alcogels, both R6G mobility and photostability register discernable changes after surface charges are respectively reversed and neutralized by aminopropyltriethoxysilane (APTS) and methyltriethoxysilane (MTES) grafting. The change in R6G photostability was found to be more sensitive to surface grafting than that of mobility. In addition, silica film modification by 0.4% APTS is as efficient as that by pure MTES in lowering R6G photostability, which suggests that surface charge reversal is more effective than charge neutralization

  17. Gel bead composition for metal adsorption

    Science.gov (United States)

    Scott, Charles D.; Woodward, Charlene A.; Byers, Charles H.

    1990-01-01

    The invention is a gel bead comprising propylene glycol alginate and bone gelatin and is capable of removing metals such as Sr and Cs from solution without adding other adsorbents. The invention could have application to the nuclear industry's waste removal activities.

  18. Gel phase in hydrated calcium dipicolinate

    Science.gov (United States)

    Rajak, Pankaj; Mishra, Ankit; Sheng, Chunyang; Tiwari, Subodh; Krishnamoorthy, Aravind; Kalia, Rajiv K.; Nakano, Aiichiro; Vashishta, Priya

    2017-11-01

    The mineralization of dipicolinic acid (DPA) molecules in bacterial spore cores with Ca2+ ions to form Ca-DPA is critical to the wet-heat resistance of spores. This resistance to "wet-heat" also depends on the physical properties of water and DPA in the hydrated Ca-DPA-rich protoplasm. Using reactive molecular dynamics simulations, we have determined the phase diagram of hydrated Ca-DPA as a function of temperature and water concentration, which shows the existence of a gel phase along with distinct solid-gel and gel-liquid phase transitions. Simulations reveal monotonically decreasing solid-gel-liquid transition temperatures with increasing hydration, which explains the experimental trend of wet-heat resistance of bacterial spores. Our observation of different phases of water also reconciles previous conflicting experimental findings on the state of water in bacterial spores. Further comparison with an unmineralized hydrated DPA system allows us to quantify the importance of Ca mineralization in decreasing diffusivity and increasing the heat resistance of the spore.

  19. Simple Cloud Chambers Using Gel Ice Packs

    Science.gov (United States)

    Kamata, Masahiro; Kubota, Miki

    2012-01-01

    Although cloud chambers are highly regarded as teaching aids for radiation education, school teachers have difficulty in using cloud chambers because they have to prepare dry ice or liquid nitrogen before the experiment. We developed a very simple and inexpensive cloud chamber that uses the contents of gel ice packs which can substitute for dry…

  20. 21 CFR 520.1452 - Moxidectin gel.

    Science.gov (United States)

    2010-04-01

    ...) Limitations. For oral use in horses and ponies 6 months of age and older. Not for use in horses and ponies... Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1452 Moxidectin gel. (a...

  1. The Sol-Gel-Xerogel Transition

    Science.gov (United States)

    1993-11-01

    relative mobili- ty are supported by the ESR (Electron Spin Resonance) studies of * * * Ikoma et al. [301 demonstrating that polyamine copper(II) chelates...deactivation of the triplet state of the molecule in the case of RTP. Recent studies on the photoisomerization of azobenzene in sol-gel glass films by

  2. Sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS ...

    African Journals Online (AJOL)

    Four strains of eri, Samia cynthia ricini Lepidoptera: Saturniidae that can be identified morphologically and maintained at North East Institute of Science and Technology, Jorhat were characterized based on their protein profile by sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) and DNA by random ...

  3. Preparing size markers for gel electrophoresis.

    Science.gov (United States)

    Nilsen, Timothy W

    2013-12-01

    Here we present two simple methods for preparing radiolabeled size markers for gel electrophoresis. The first procedure describes the generation of an RNA marker ladder by the alkaline hydrolysis of (32)P 5'- or 3'-end-labeled RNA. The second procedure describes the labeling of DNA fragments produced by digestion of pBR322 with the restriction enzyme MspI.

  4. Denaturing urea polyacrylamide gel electrophoresis (Urea PAGE).

    Science.gov (United States)

    Summer, Heike; Grämer, René; Dröge, Peter

    2009-10-29

    Urea PAGE or denaturing urea polyacrylamide gel electrophoresis employs 6-8 M urea, which denatures secondary DNA or RNA structures and is used for their separation in a polyacrylamide gel matrix based on the molecular weight. Fragments between 2 to 500 bases, with length differences as small as a single nucleotide, can be separated using this method(1). The migration of the sample is dependent on the chosen acrylamide concentration. A higher percentage of polyacrylamide resolves lower molecular weight fragments. The combination of urea and temperatures of 45-55 degrees C during the gel run allows for the separation of unstructured DNA or RNA molecules. In general this method is required to analyze or purify single stranded DNA or RNA fragments, such as synthesized or labeled oligonucleotides or products from enzymatic cleavage reactions. In this video article we show how to prepare and run the denaturing urea polyacrylamide gels. Technical tips are included, in addition to the original protocol (1,2).

  5. Polyacrylamide gel polymerization with adjustable gelation rate

    Czech Academy of Sciences Publication Activity Database

    Wiesner, Ivo; Wiesnerová, Dana

    2002-01-01

    Roč. 32, - (2002), s. 740-742 ISSN 0736-6205 R&D Projects: GA AV ČR KSK5052113; GA ČR GA521/00/0075 Keywords : polyacrylamide gel Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.173, year: 2002

  6. Thermal Decomposition Characteristics of ADU Gel Spheres

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Kyung Chai; Eom, Sung Ho; Kim, Yeon Ku; Kim, Young Min; Kim, Woong Ki; Kim, Bong Ku; Lee, Young Woo; Cho, Moon Seoung [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2013-10-15

    HTGR nuclear fuel uses a modified sol.gel GSP (Gel Supported Precipitation) method, which is a wet method used in most countries. ADU(Ammonium DiUranate) gel particles fabricated in this way pass through thermal treatments and become final UO{sub 2} microspheres. The washing characteristics such as washing volume, duration, and times during AWD(ageing, washing and drying) process after the spherical ADU gel particles preparation by the GSP method was studied. The VHTR (Very High Temperature Gas Reactor) is one of the reactor concepts in the Gen IV International Collaboration. Unlike light water reactor currently in use in Korea, a HTGR actually functions as a gas cooled reactor where the high temperature heat generated from nuclear fission in a reactor is cooled by He gas, with uranium dioxide (UO{sub 2} is globally used) used as fuel for the nuclear fission. Generally, nuclear fuel used in a HTGR is fabricated into a TRISO (TRi.ISOtropic) structure that can prevent the leakage of nuclear fission products at high temperatures.

  7. Screening of mucoadhesive vaginal gel formulations

    Directory of Open Access Journals (Sweden)

    Ana Ochoa Andrade

    2014-12-01

    Full Text Available Rational design of vaginal drug delivery formulations requires special attention to vehicle properties that optimize vaginal coating and retention. The aim of the present work was to perform a screening of mucoadhesive vaginal gels formulated with carbomer or carrageenan in binary combination with a second polymer (carbomer, guar or xanthan gum. The gels were characterised using in vitroadhesion, spreadability and leakage potential studies, as well as rheological measurements (stress and frequency sweep tests and the effect of dilution with simulated vaginal fluid (SVF on spreadability. Results were analysed using analysis of variance and multiple factor analysis. The combination of polymers enhanced adhesion of both primary gelling agents, carbomer and carrageenan. From the rheological point of view all formulations presented a similar behaviour, prevalently elastic and characterised by loss tangent values well below 1. No correlation between rheological and adhesion behaviour was found. Carbomer and carrageenan gels containing the highest percentage of xanthan gum displayed good in vitro mucoadhesion and spreadability, minimal leakage potential and high resistance to dilution. The positive results obtained with carrageenan-xanthan gum-based gels can encourage the use of natural biocompatible adjuvants in the composition of vaginal products, a formulation field that is currently under the synthetic domain.

  8. Two-dimensional gel isoelectric focusing

    Czech Academy of Sciences Publication Activity Database

    Šťastná, Miroslava; Šlais, Karel

    2005-01-01

    Roč. 26, č. 18 (2005), s. 3586-3591 ISSN 0173-0835 R&D Projects: GA AV ČR IAA4031302; GA AV ČR IBS4031201 Institutional research plan: CEZ:AV0Z40310501 Keywords : gel isoelectric focusing * pI markers * proteins Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 3.850, year: 2005

  9. Effectiveness of Gel Repellents on Feral Pigeons

    Directory of Open Access Journals (Sweden)

    Birte Stock

    2013-12-01

    Full Text Available Millions of feral pigeons (Columba livia live in close association with the human population in our cities. They pose serious health risks to humans and lead to high economic loss due to damage caused to buildings. Consequently, house owners and city authorities are not willing to allow pigeons on their buildings. While various avian repellents are regularly introduced onto the market, scientific proof of efficacy is lacking. This study aimed at testing the effectiveness of two avian gel repellents and additionally examined their application from animal welfare standpoint. The gels used an alleged tactile or visual aversion of the birds, reinforced by additional sensory cues. We mounted experimental shelves with the installed repellents in a pigeon loft and observed the behavior of free-living feral pigeons towards the systems. Both gels showed a restricted, transient repellent effect, but failed to prove the claimed complete effectiveness. Additionally, the gels’ adhesive effect remains doubtful in view of animal welfare because gluing of plumage presents a risk to feral pigeons and also to other non-target birds. This study infers that both gels lack the promised complete efficacy, conflict with animal welfare concerns and are therefore not suitable for feral pigeon management in urban areas.

  10. Gels and microgels for nanotechnological applications.

    Science.gov (United States)

    Fernández-Barbero, Antonio; Suárez, Iván J; Sierra-Martín, B; Fernández-Nieves, A; de Las Nieves, F Javier; Marquez, Manuel; Rubio-Retama, J; López-Cabarcos, Enrique

    2009-01-01

    In recent years, "smart" materials have been the focus of considerable interest, from both fundamental and applied perspectives. Polymer gels are within this category; they respond to specific environmental stimuli by changing their size. Thus, the internal structure, the refractive index, and the mechanical properties of the polymer network change. They are considered super absorbent materials, as they can absorb solvent up to several hundred times their own weight. They respond rapidly to local environmental variations, an important fact in device miniaturization and microsensor developments. As size changes are accompanied by changes in internal dimensions, microgels have found application as carriers of therapeutic drugs and as diagnostic agents. They have also been used as microreactors, optically active materials, for template synthesis of nanoparticles or fabrication of artificial muscle. In this paper we review a set of application based on the special features associated to this systems. Basic concepts on the physical-chemistry of gel swelling is first described, followed by different applications covering drug delivery, composite materials using polymer gels to modulate optical or magnetic and electrical properties, molecular imprinting, gel-based biosensors and polymer sensors and actuators used in the field of artificial muscles.

  11. Sol-Gel Derived Hafnia Coatings

    Science.gov (United States)

    Feldman, Jay D.; Stackpoole, Mairead; Blum, Yigal; Sacks, Michael; Ellerby, Don; Johnson, Sylvia M.; Venkatapathy, Ethiras (Technical Monitor)

    2002-01-01

    Sol-gel derived hafnia coatings are being developed to provide an oxidation protection layer on ultra-high temperature ceramics for potential use in turbine engines (ultra-efficient engine technology being developed by NASA). Coatings using hafnia sol hafnia filler particles will be discussed along with sol synthesis and characterization.

  12. Formulation of Bioadhesive Carbomer Gel Incorporating Drug ...

    African Journals Online (AJOL)

    Purpose: To formulate carbomer gel to localize and target drug action in periodontal pockets. Methods: Diclofenac sodium (DS, anti-inflammatory) and metronidazole hydrochloride (MH, antibacterial) were loaded in gelatin microspheres using glutaraldehyde cross-linking. The microspheres were evaluated for drug loading, ...

  13. Sol–gel processing of carbidic glasses

    Indian Academy of Sciences (India)

    Unknown

    The endothermic peak and weight loss below. 200°C are associated with condensation reactions and evaporation of reaction products and residual water. The extent of these have been found to be lower than those for pure silica gels. The weight loss after 400°C is assigned to condensation of silanol groups and formation ...

  14. Fluorescence metrology of silica sol-gels

    Indian Academy of Sciences (India)

    We have developed a new method for measuring in-situ the growth of the nanometre-size silica particles which lead to the formation of sol-gel glasses. This technique is based on the decay of fluorescence polarisation anisotropy due to Brownian rotation of dye molecules bound to the particles. Results to date give near ...

  15. (3-Mercaptopropyl)trimethoxysilane-derived Porous Gel Monolith via Thioacetal Reaction-Assisted Sol-Gel Route

    Energy Technology Data Exchange (ETDEWEB)

    Ito, S; Nishi, M; Kurahashi, T; Matsubara, S; Shimotsuma, Y; Miura, K; Hirao, K [Department of Material Chemistry, Graduate School of Engineering, Kyoto University, Kyoto-Daigaku-Katsura, Nishikyo-ku, Kyoto 615-8510 (Japan); Kanamori, K; Nakanishi, K, E-mail: west@collon1.kuic.kyoto-u.ac.jp [Department of Chemistry, Graduate School of Science, Kyoto University, Kitashirakawa, Sakyo-ku, Kyoto 606-8502 (Japan)

    2011-10-29

    Porous gel monolith was synthesized by reacting (3-mercaptopropyl)trimethoxysilane (MPTMS) with acetone on acidic conditions. It is known that MPTMS itself is difficult to turn into gel on acidic conditions and instead oligomers are obtained owing to the large mercaptopropyl group. In our system, the gels were obtained since acetone worked as a cross-linker via thioacetal reaction. Additionally, Au ions were selectively adsorbed on the obtained gel. When an obtained white gel was soaked in a chloroauric acid solution, the gel turned brown and was getting dark depending on the soaked time; on the other hand, the color of the solution turned from yellow to colorless.

  16. Normal modes of weak colloidal gels

    Science.gov (United States)

    Varga, Zsigmond; Swan, James W.

    2018-01-01

    The normal modes and relaxation rates of weak colloidal gels are investigated in calculations using different models of the hydrodynamic interactions between suspended particles. The relaxation spectrum is computed for freely draining, Rotne-Prager-Yamakawa, and accelerated Stokesian dynamics approximations of the hydrodynamic mobility in a normal mode analysis of a harmonic network representing several colloidal gels. We find that the density of states and spatial structure of the normal modes are fundamentally altered by long-ranged hydrodynamic coupling among the particles. Short-ranged coupling due to hydrodynamic lubrication affects only the relaxation rates of short-wavelength modes. Hydrodynamic models accounting for long-ranged coupling exhibit a microscopic relaxation rate for each normal mode, λ that scales as l-2, where l is the spatial correlation length of the normal mode. For the freely draining approximation, which neglects long-ranged coupling, the microscopic relaxation rate scales as l-γ, where γ varies between three and two with increasing particle volume fraction. A simple phenomenological model of the internal elastic response to normal mode fluctuations is developed, which shows that long-ranged hydrodynamic interactions play a central role in the viscoelasticity of the gel network. Dynamic simulations of hard spheres that gel in response to short-ranged depletion attractions are used to test the applicability of the density of states predictions. For particle concentrations up to 30% by volume, the power law decay of the relaxation modulus in simulations accounting for long-ranged hydrodynamic interactions agrees with predictions generated by the density of states of the corresponding harmonic networks as well as experimental measurements. For higher volume fractions, excluded volume interactions dominate the stress response, and the prediction from the harmonic network density of states fails. Analogous to the Zimm model in polymer

  17. Ultraviolet absorption detection of DNA in gels

    International Nuclear Information System (INIS)

    Mahon, A.R.

    1998-01-01

    A method and apparatus for the detection and quantification of large fragments of unlabelled deoxyribonucleic acid (DNA) in agarose gels is presented. The technique is based on ultra-violet (UV) absorption by nucleotides. A deuterium lamp was used to illuminate regions of an electrophoresis gel. As DNA bands passed through the illuminated region of the gel the amount of UV light transmitted was reduced due to DNA absorption. Two detection systems were investigated. In the first system, synthetic chemical vapour deposition (CVD) diamond strip detectors were used to locate regions of DNA in the gels by detecting the transmitted light. CVD diamond has a high indirect band gap of 5.45 eV and is therefore sensitive to UV photons of wavelengths < 224 nm. A number of CVD diamond samples were characterised to investigate their suitability as detectors for this application. The detectors' quantum efficiency, UV response and time response were measured. DNA bands containing as little as 20 ng were detected by the diamond. In a second system, a deuterium lamp was used to illuminate individual sample lanes of an electrophoresis gel via an array of optical fibres. During electrophoresis the regions of DNA were detected with illumination at 260 nm, using a UV-sensitive charge coupled device (CCD). As the absorption coefficient of a DNA sample is approximately proportional to its mass, the technique is inherently quantitative. This system had a detection limit of 0.25 ng compared with 2-10 ng for the most popular conventional technique, ethidium bromide (EtBr) staining. Using this detection technique, the DNA sample remains in its native state. The removal of carcinogenic dyes from the detection procedure greatly reduces associated biological hazards. (author)

  18. Sol-Gel Synthesis of Au-Nanoparticle Dispersed Bicontinuous Macroporous Siloxane Gel

    Energy Technology Data Exchange (ETDEWEB)

    Hamada, Y; Nishi, M; Shimotsuma, Y; Miura, K; Hirao, K, E-mail: west@collon1.kuic.kyoto-u.ac.jp [Department of Material Chemistry, Graduate School of Engineering, Kyoto University, Nishikyo-ku, Kyoto 615-8510 (Japan)

    2011-10-29

    We synthesized Au-nanoparticle dispersed siloxane gel with well-defined bicontinuous macroporous morphologies. We employed methyltrimethoxysilane (MTMS) as a precursor of the gel skeleton, and also employed hydrogen tetrachloroaurate(III) as both a precursor of Au nanoparticles and an acid catalyst for hydrolysis/condensation of methoxysilanes. The effect of adding (3-mercaptopropyl)trimethoxysilane (MPTMS) as a starting material on the obtained structure was also investigated. It is found that Au nanoparticles of 20-30 nm in grain size are uniformly dispersed on the gel surface in the system containing MPTMS; in contrast, Au nanoparticles assembled in the pits in the MPTMS-free system. All the heat-treated MPTMS-containing gels showed surface plasmon absorption, and the peaks shifted from 550 to 520 nm with increasing the calcination temperature.

  19. A randomized comparison of extra-amniotic saline infusion and intracervical dinoprostone gel for cervical ripening.

    Science.gov (United States)

    Goldman, J B; Wigton, T R

    1999-02-01

    To compare extra-amniotic saline infusion to intracervical dinoprostone gel for preinduction cervical ripening. Women with Bishop scores less than 5 were assigned randomly to either extra-amniotic saline infusion (n = 26) or intracervical dinoprostone gel (n = 26) for preinduction cervical ripening. A sample size of 50 would have 80% power to detect a 10-hour difference in the mean time from start of cervical ripening to delivery for the two methods of intervention, with a type I error of .05. The study populations were similar in age, gestational age, and initial Bishop score. They differed in parity, with 22 nulliparas in the extra-amniotic saline infusion group versus 13 in the dinoprostone gel group (relative risk [RR] 1.69, 95% confidence interval [CI] 1.11, 2.57). The number of women achieving a favorable Bishop score at 6 hours was greater with extra-amniotic saline infusion (n = 20) than dinoprostone gel (n = 9) (RR 2.14, 95% CI 1.22, 3.75). Mean time from start of ripening to delivery was 25.9 hours with extra-amniotic saline infusion and 30.2 hours with dinoprostone gel (P = .25). Birth weight, Apgar scores, umbilical artery pH, and infectious morbidity were similar between groups. More women achieved a favorable Bishop score at 6 and 12 hours after the start of cervical ripening with extra-amniotic saline infusion compared with dinoprostone gel. Saline infusion is as safe as dinoprostone gel for preinduction cervical ripening.

  20. Gel polymer electrolytes based on PMMA III. PMMA gels containing cadmium

    Czech Academy of Sciences Publication Activity Database

    Vondrák, Jiří; Sedlaříková, M.; Velická, Jana; Klápště, Břetislav; Novák, V.; Reiter, Jakub

    2003-01-01

    Roč. 48, č. 8 (2003), s. 1001-1004 ISSN 0013-4686 R&D Projects: GA AV ČR IAA4032002; GA ČR GA104/02/0731; GA MŠk ME 216 Institutional research plan: CEZ:AV0Z4032918; CEZ:MSM 262200010 Keywords : gel polymer electrolytes * polymethylmethacrylate * cadmium gel electrolyte Subject RIV: CA - Inorganic Chemistry Impact factor: 1.996, year: 2003

  1. Simplified riboprobe purification using translucent straws as gel tubes.

    Science.gov (United States)

    Kol, S; Ben-Shlomo, I; Adashi, E Y; Rohan, R M

    1996-01-01

    Gel purification of radioactive riboprobes enhances the quality of the ribonuclease protection assay. A simple and effective method for riboprobe purification is described. The method uses acrylamide gels in plastic tubes to achieve electrophoretic separation of the RNA polymerase products.

  2. Accumulation of humic acid in DET/DGT gels

    Digital Repository Service at National Institute of Oceanography (India)

    Van der Veeken, P.L.R.; Chakraborty, P.; Van Leeuwen, H.P.

    in Thin film) that these natural complexing agents do enter the gel layer, and that humic acids even appear to accumulate in the gel, with enrichment factors typicallyonthe order of 10. The results have consequences for the interpretation of DGT...

  3. Study of nuclear glasses alteration gel and synthesis of some model gels

    International Nuclear Information System (INIS)

    Ricol, S.

    1995-01-01

    This work deals with the general problem of alteration of the reference nuclear glass R7T7. Attention is paid particularly to the altered layer formed at the glass surface during alteration process. In opposition to previous works, related essentially to glass dissolution kinetics based on chemical analyses of lixiviated elements, this thesis deals with alteration problems through structural studies of the reference glass and derived gel. This approach allows the determination of mechanisms for the gel formation and a better understanding of the behaviour of glasses towards lixiviation. Both approaches appeared complementary. Based on several spectroscopic techniques, this work showed the particular role of cations such as calcium, zirconium and iron. Studies of silica-based synthetic gels showed the synergic effect of formers cation and of one highly coordinated cation. The variation of the wavenumber related to Si-O-Si asymmetric stretching vibration can be correlated to O/Si ratio for ternary systems Si/Na/Zr. On the contrary, the Si losses of the materials depend on the number of non-bridging oxygen atoms. In the perspective of long-term behaviour, the alteration gel presents better characteristics than initial glass. It is therefore a highly stable material in static conditions. In the same way, synthetic gels are materials with very low solubilities (much lower than the alteration gel) and could be used as confining matrices. (authors). refs., 71 figs., 37 tabs

  4. Establishment of gel materials with different mechanical properties by 3D gel printer SWIM-ER

    Science.gov (United States)

    Ota, Takafumi; Tase, Taishi; Okada, Koji; Saito, Azusa; Takamatsu, Kyuuichiro; Kawakami, Masaru; Furukawa, Hidemitsu

    2016-04-01

    A 3D printer is a device which can directly produce objects whose shape is the same as the original 3D digital data. Hydrogels have unique properties such as high water content, low frictional properties, biocompatibility, material permeability and high transparency, which are rare in hard and dry materials. These superior characteristics of gels promise useful medical applications. We have been working on the development of a 3D gel printer, SWIM-ER (Soft and Wet Industrial - Easy Realizer), which can make models of organs and artificial blood vessels with gel material. However, 3D printing has a problem: the mechanical properties of the printed object vary depending on printing conditions, and this matter was investigated with SWIM-ER. In the past, we found that mechanical properties of 3D gel objects depend on the deposition orientation in SWIM-ER. In this study, gels were printed with different laser scanning speeds. The mechanical properties of these gels were investigated by compression tests, water content measurements and SMILS (Scanning Microscopic Light Scattering).

  5. Polymer gel dosimetry system for radiation therapy

    International Nuclear Information System (INIS)

    Maryanski, M.J.; Schulz, R.J.; Gignac, C.; Eastman, P.; Gore, J.C.

    1995-01-01

    Purpose/Objective: Recently developed treatment modalities such as stereotactic and conformal radiation therapy produce complex dose distributions which are difficult or impractical to measure with conventional dosimetry instrumentation. Three-dimensional treatment planning systems which purport to calculate these complex dose distributions should be compared to experimental results before being routinely applied to clinical problems. There is a need for a new class of tissue-equivalent dosimeters capable of providing accurate, high resolution, time-integrated and three dimensional dose distributions. The recently developed BANG polymer gel dosimetry system (MGS Research, Inc., Guilford, CT) is ideally suited for the task described above. Physico-chemical principles of the polymer gel dosimetry are presented, together with examples of its application to radiation therapy. Data analysis and display program, written for Macintosh computer, is demonstrated. Materials and Methods: Radiation-induced polymerization of acrylic monomers, which are dispersed in tissue-equivalent gelatin, has been shown to be dependent on the dose, but independent of the dose rate or photon energy. Therefore, the spatial distribution of polymer in the gel is precisely representative of the dose distribution. As the polymeric microparticles reduce the water proton NMR relaxation times in the gel, the dose distribution can be measured with high resolution and accuracy using magnetic resonance imaging. Also, as these microparticles cannot diffuse through the gelatin matrix, their distribution is permanent. An improved formulation of the BANG dosimeter consists of 3% w/v acrylic acid, 3% N,N'-methylene-bis-acrylamide, 1% sodium hydroxide, 5% gelatin, and 88% water. MR images are transferred via a local network to a Macintosh computer, and R2 maps constructed on the basis of multiple TE images, using a non-linear least squares fit based on the Levenberg-Marquardt algorithm. A dose-to-R2

  6. Prenatal Virilization Associated with Paternal Testosterone Gel Therapy

    OpenAIRE

    Patel, Anisha; Rivkees, Scott A.

    2010-01-01

    Transdermal testosterone gels are used in the treatment of hypoandrogenism of males. Virilization due to exposure to testosterone gels has been reported in children resulting in a US Food and Drug Administration (FDA) warning about secondary exposure to these products. At present, we are unaware of prenatal virilization associated with unintentional testosterone gel exposure. We report prenatal virilization in a female infant due to secondary maternal exposure to the father's testosterone gel...

  7. Development and dosimetric evaluation of radiochromic PCDA vesicle gel dosimeters

    International Nuclear Information System (INIS)

    Sun, P.; Fu, Y.C.; Hu, J.; Hao, N.; Huang, W.; Jiang, B.

    2016-01-01

    The gel dosimeter has the unique capacity in recording radiation dose distribution in three dimensions (3D), which has the specific advantages in dosimetry measurements where steep dose gradients exist, such as in intensity-modulated radiation therapy (IMRT), brachytherapy and so on. Some 3D dosimeters, such as Fricke gel dosimeters, polymer gel dosimeters, the PRESAGE plastic dosimeters and micelle gel dosimeters have appeared recently. However, there are several disadvantages of these 3D dosimeters limit their application in radiotherapy dose verification. In this study, a novel radiochromic gel dosimeter for 3D dose verification of radiotherapy was developed by dispersing nanovesicles self-assembled by 10,12-pentacosadiynoic acid (PCDA) into the tissue equivalence gel matrix. The characteristics of radiochromic PCDA vesicle gel dosimeters were evaluated. The results indicate that these radiochromic gel dosimeters have good linear dose response to X-ray irradiation in the dose range of 2–100 Gy. In addition, the radiochromic gel dosimeters breakthrough the limitations of the existing gel dosimeters such as diffusion effect, post-radiation effect, and poor forming ability. The response of the gel dosimeter does not show any dose rate dependence, energy dependence and temperature effect, and there was no obvious difference in the gel response between single and cumulative dose of fractional irradiation. Hence, the radiochromic PCDA vesicle gel dosimeters developed in this study could be generally applied to 3D dose verification in radiotherapy. - Highlights: • A novel radiochromic gel dosimeter was developed by dispersing PCDA nanovesicles into the tissue equivalence gel matrix. • This nanovesicle overcomes the dose image blurring caused by the diffusion of monomer molecules. • This nanovesicle limits the polymer chain growth, so as to reduce the post-radiation effect. • The gel matrixes possess excellent tissue equivalence and elastic strength, which

  8. Implementation of a gel dosimeter for dosimetric verification of treatments with RapidArcTM

    International Nuclear Information System (INIS)

    Cortes, H.; Vasquez, J.; Plazas, M.

    2014-08-01

    The gel dosimetry represents advantages on other dosimetric systems for its potential of analyzing information in third dimension (3D). This work seeks to find another alternative for the verification of treatments of high complexity like the RapidArc TM . A gel type Magic was prepared and characterized, which was irradiated with base in a plan of RapidArc TM calculated in the Treatment Planning System (Tps) Eclipse, using the Anisotropic Analytic Algorithm (Aaa) for a beam with an acceleration potential of 6 MV. The dosimeter was characterized using Magnetic Resonance Images starting from the correlation between the T2 and the dose. The dose distribution curves were analyzed in second dimension (2D) using the program Omni Pro-I mrT and were compared with the curves obtained for the Tps under the approach gamma 2D. The comparison showed that the Gel represents a valid option inside the acceptable ranges for Quality Assurance in radiotherapy. (Author)

  9. Synthesis and Characterization of Cellulose-Based Hydrogels to Be Used as Gel Electrolytes

    Directory of Open Access Journals (Sweden)

    Maria Assunta Navarra

    2015-11-01

    Full Text Available Cellulose-based hydrogels, obtained by tuned, low-cost synthetic routes, are proposed as convenient gel electrolyte membranes. Hydrogels have been prepared from different types of cellulose by optimized solubilization and crosslinking steps. The obtained gel membranes have been characterized by infrared spectroscopy, scanning electron microscopy, thermogravimetric analysis, and mechanical tests in order to investigate the crosslinking occurrence and modifications of cellulose resulting from the synthetic process, morphology of the hydrogels, their thermal stability, and viscoelastic-extensional properties, respectively. Hydrogels liquid uptake capability and ionic conductivity, derived from absorption of aqueous electrolytic solutions, have been evaluated, to assess the successful applicability of the proposed membranes as gel electrolytes for electrochemical devices. To this purpose, the redox behavior of electroactive species entrapped into the hydrogels has been investigated by cyclic voltammetry tests, revealing very high reversibility and ion diffusivity.

  10. A SEM evaluation of a 6% hydrogen peroxide tooth whitening gel on dental materials in vitro.

    Science.gov (United States)

    Schemehorn, Bruce; González-Cabezas, Carlos; Joiner, Andrew

    2004-01-01

    The aim of this study was to evaluate the effects of a novel 6% hydrogen peroxide gel on the surface morphology of dental gold, amalgam, porcelain and composite. Admixed high-copper amalgam and hybrid resin composite specimens were prepared in extracted teeth using standard clinical procedures. Feldspathic porcelain and type III gold specimens were prepared in a mould using standard laboratory procedures. One half of the specimens were covered with nail varnish to serve as the control side, leaving the other half exposed. The specimens were treated with pooled whole saliva (1 h), followed by the peroxide gel (20 min), rinsing with water and returning to saliva. This cycling protocol was continued until a total of 28 treatments with the peroxide gel were completed. The samples were prepared for SEM. There were no observable differences at 200x and 2000x magnifications between the control and peroxide gel treated sides on any of the materials tested. There were no significant effects of the 6% hydrogen peroxide gel on the surface morphology of any of the dental materials tested.

  11. Effect of the concentration on sol-gel transition of telechelic polyelectrolytes.

    Science.gov (United States)

    Zhang, Ran; Shi, Tongfei; Li, Hongfei; An, Lijia

    2011-01-21

    Telechelic polyelectrolytes, bearing short hydrophobic blocks at both ends, will ionize into polyions and their counterions when dissolved in water. With the variation of concentration, the interplay between short range attraction and the long range electrostatic interaction as well as the counterion distribution exerts a major influence on the chain conformations (two basic conformations: loop and nonloop, the latter can be subdivided into three association types: free, dangling, and bridge), the cluster structure and the forming of a physical gel. For weak hydrophobic interaction, the relative strong electrostatic interaction dominates the gelation progress; sol-gel transition occurs at higher concentrations due to electrostatic screening and mainly involves the forming of stretched nonloop conformations such as dangling and bridge. While for strong hydrophobic interaction, the hydrophobic interaction dominates and the electrostatic interaction provides a contribution to the formation of gels by maintaining a spatial swelling structure, resulting in a much lower concentration region of sol-gel transition; besides, the sol-gel transition is characterized by the competition of the forming of loop and bridge chains.

  12. A Supramolecular Gel Approach to Minimize the Neural Cell Damage during Cryopreservation Process.

    Science.gov (United States)

    Zeng, Jie; Yin, Yixia; Zhang, Li; Hu, Wanghui; Zhang, Chaocan; Chen, Wanyu

    2016-03-01

    The storage method for living cells is one of the major challenges in cell-based applications. Here, a novel supramolecular gel cryopreservation system (BDTC gel system) is introduced, which can observably increase the neural cell viability during cryopreservation process because this system can (1) confine the ice crystal growth in the porous of BDTC gel system, (2) decrease the amount of ice crystallization and cryopreservation system's freezing point, and (3) reduce the change rates of cell volumes and osmotic shock. In addition, thermoreversible BDTC supramolecular gel is easy to be removed after thawing so it does not hinder the adherence, growth, and proliferation of cells. The results of functionality assessments indicate that BDTC gel system can minimize the neural cell damage during cryopreservation process. This method will be potentially applied in cryopreservation of other cell types, tissues, or organs and will benefit cell therapy, tissue engineering, and organs transplantation. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. MALDI analysis of proteins after extraction from dissolvable ethylene glycol diacrylate cross-linked polyacrylamide gels.

    Science.gov (United States)

    Papasotiriou, Dimitrios G; Markoutsa, Stavroula; Gorka, Jan; Schleiff, Enrico; Karas, Michael; Meyer, Bjoern

    2013-09-01

    Although the extraction of intact proteins from polyacrylamide gels followed by mass spectrometric molecular mass determination has been shown to be efficient, there is room for alternative approaches. Our study evaluates ethylene glycol diacrylate, a cleavable cross-linking agent used for a new type of dissolvable gels. It attains an ester linkage that can be hydrolyzed in alkali conditions. The separation performance of the new gel system was tested by 1D and 2D SDS-PAGE using the outer chloroplast envelope of Pisum sativum as well as a soluble protein fraction of human lymphocytes, respectively. Gel spot staining (CBB), dissolving, and extracting were conducted using a custom-developed workflow. It includes protein extraction with an ammonia-SDS buffer followed by methanol treatment to remove acrylamide filaments. Necessary purification for MALDI-TOF analysis was implemented using methanol-chloroform precipitation and perfusion HPLC. Both cleaning procedures were applied to several standard proteins of different molecular weight as well as 'real' biological samples (8-75 kDa). The protein amounts, which had to be loaded on the gel to detect a peak in MALDI-TOF MS, were in the range of 0.1 to 5 μg, and the required amount increased with increasing mass. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Leuco-crystal-violet micelle gel dosimeters: Component effects on dose-rate dependence

    Science.gov (United States)

    Xie, J. C.; Katz, E. A. B.; Alexander, K. M.; Schreiner, L. J.; McAuley, K. B.

    2017-05-01

    Designed experiments were performed to produce empirical models for the dose sensitivity, initial absorbance, and dose-rate dependence respectively for leucocrystal violet (LCV) micelle gel dosimeters containing cetyltrimethylammonium bromide (CTAB) and 2,2,2-trichloroethanol (TCE). Previous gels of this type showed dose-rate dependent behaviour, producing an ∼18% increase in dose sensitivity between dose rates of 100 and 600 cGy min-1. Our models predict that the dose rate dependence can be reduced by increasing the concentration of TCE, CTAB and LCV. Increasing concentrations of LCV and CTAB produces a significant increase in dose sensitivity with a corresponding increase in initial absorbance. An optimization procedure was used to determine a nearly dose-rate independent gel which maintained high sensitivity and low initial absorbance. This gel which contains 33 mM CTAB, 1.25 mM LCV, and 96 mM TCE in 25 mM trichloroacetic acid and 4 wt% gelatin showed an increase in dose sensitivity of only 4% between dose rates of 100 and 600 cGy min-1, and provides an 80% greater dose sensitivity compared to Jordan’s standard gels with similar initial absorbance.

  15. Double-network gels and the toughness of terrestrial slug glue.

    Science.gov (United States)

    Wilks, Alex M; Rabice, Sarah R; Garbacz, Holland S; Harro, Cailin C; Smith, Andrew M

    2015-10-01

    The terrestrial slug Arion subfuscus produces a defensive secretion that is sticky and tough, despite being a dilute gel. It is unusual in having high stiffness for a gel, yet retaining the high extensibility typical of mucus. In tensile tests, it sustains an average peak stress of 101 kPa, and fails at an average strain of 9.5. This gives the gel toughness; it requires much greater strain energy to fracture than most gels. This toughness may arise from a double-network type mechanism. In this mechanism, two separate, interpenetrating networks of polymers with different properties combine to give toughness that can be several orders of magnitude greater than either network individually. Native gel electrophoresis suggests that A. subfuscus glue consists of two networks: a network of negatively charged proteins ranging in Mr from 40×10(3) to 220×10(3) that can be dissociated by hydroxylamine and a network of heparan sulfate-like proteoglycans. The two networks are not tightly linked, though proteins of Mr 40×10(3) and 165×10(3) may associate with the carbohydrates. Targeted disruption of either network separately, using enzymatic hydrolysis, disulfide bond breakage or imine bond disruption completely disrupted the glue, resulting in no measurable toughness. Thus, the two networks separately provide little toughness, but together they work synergistically to create a tough material, as predicted in the double-network mechanism. © 2015. Published by The Company of Biologists Ltd.

  16. Sequence Dependent Electrophoretic Separations of DNA in Pluronic F127 Gels

    Science.gov (United States)

    You, Seungyong; van Winkle, David H.

    2010-03-01

    Two-dimensional (2-D) electrophoresis has successfully been used to visualize the separation of DNA fragments of the same length. We electrophorese a double-stranded DNA ladder in an Agarose gel for the first dimension and in gels of Pluronic F127 for the second dimension at room temperature. The 1000 bp band that travels together as a single band in an Agarose gel is split into two bands in Pluronic gels. The slower band follows the exponential decay trend that the other ladder constituents do. After sequencing the DNA fragments, the faster band has an apparently random sequence, while the slower band and the others have two A-tracts in each 250 bp segment. The A-tracts consist of a series of at least five adenine bases pairing with thymine bases. This result leads to the conclusion that the migration of the DNA molecules bent with A-tracts is more retarded in Pluronic gels than the wild-type of DNA molecules.

  17. Viscoelastic nature of Au nanoparticle–PDMS nanocomposite gels

    Indian Academy of Sciences (India)

    Even a very low Au content of 0.09 wt% is sufficient enough to bring in the transition from sponge state to gel state at room temperature. ... gel properties can have direct influence on the processability of Au nanoparticle–PDMS nanocomposite gels, with interesting implications in electronic, optical and microfluidic devices.

  18. Formulation and method for preparing gels comprising hydrous hafnium oxide

    Science.gov (United States)

    Collins, Jack L; Hunt, Rodney D; Montgomery, Frederick C

    2013-08-06

    Formulations useful for preparing hydrous hafnium oxide gels contain a metal salt including hafnium, an acid, an organic base, and a complexing agent. Methods for preparing gels containing hydrous hafnium oxide include heating a formulation to a temperature sufficient to induce gel formation, where the formulation contains a metal salt including hafnium, an acid, an organic base, and a complexing agent.

  19. Power Law Behavior of Structural Properties of Protein Gels

    NARCIS (Netherlands)

    Verheul, Marleen; Roefs, Sebastianus P.F.M.; Mellema, J.; Kruif, Kees G.

    1998-01-01

    Whey proteins are globular, heat-sensitive proteins. The gel structure, the formation of this structure, and the rheological properties of particulate whey protein isolate (WPI) gels have been investigated. On increasing the NaCl concentration, the permeability of the WPI gels increased, indicating

  20. Outdoor weathering of sol-gel-treated wood

    Science.gov (United States)

    Mandla A Tshabalala; Ryan Libert; Nancy Ross Sutherland

    2009-01-01

    Outdoor weathering of wood specimens treated with sol-gel formulations based on methyltrimethoxysilane (MTMOS), hexadecyltrimethoxysilane (HDTMOS), and ferric-zirconia-titania (Fe-Zr-Ti) sol was evaluated. The sol-gel process allowed deposition of a thin film of hybrid inorganic-organic networks (gel) in the wood cell wall that resulted in improved outdoor weathering...

  1. Agarose Gel Size Selection for DNA Sequencing Libraries.

    Science.gov (United States)

    Mardis, Elaine; McCombie, W Richard

    2017-08-01

    Agarose gel electrophoresis may be used to purify fragmented genomic DNA after ligation of adaptors. After electrophoresis, the region of the gel containing the desired size range of DNA is excised, and the DNA is subsequently extracted from the gel and purified by passage through a spin column. © 2017 Cold Spring Harbor Laboratory Press.

  2. Formulation and method for preparing gels comprising hydrous aluminum oxide

    Science.gov (United States)

    Collins, Jack L.

    2014-06-17

    Formulations useful for preparing hydrous aluminum oxide gels contain a metal salt including aluminum, an organic base, and a complexing agent. Methods for preparing gels containing hydrous aluminum oxide include heating a formulation to a temperature sufficient to induce gel formation, where the formulation contains a metal salt including aluminum, an organic base, and a complexing agent.

  3. Soft fibrin gels promote selection and growth of tumorigenic cells

    Science.gov (United States)

    Liu, Jing; Tan, Youhua; Zhang, Huafeng; Zhang, Yi; Xu, Pingwei; Chen, Junwei; Poh, Yeh-Chuin; Tang, Ke; Wang, Ning; Huang, Bo

    2012-08-01

    The identification of stem-cell-like cancer cells through conventional methods that depend on stem cell markers is often unreliable. We developed a mechanical method for selecting tumorigenic cells by culturing single cancer cells in fibrin matrices of ~100 Pa in stiffness. When cultured within these gels, primary human cancer cells or single cancer cells from mouse or human cancer cell lines grew within a few days into individual round colonies that resembled embryonic stem cell colonies. Subcutaneous or intravenous injection of 10 or 100 fibrin-cultured cells in syngeneic or severe combined immunodeficiency mice led to the formation of solid tumours at the site of injection or at the distant lung organ much more efficiently than control cancer cells selected using conventional surface marker methods or cultured on conventional rigid dishes or on soft gels. Remarkably, as few as ten such cells were able to survive and form tumours in the lungs of wild-type non-syngeneic mice.

  4. Sol-gel derived ceramic electrolyte films on porous substrates

    Energy Technology Data Exchange (ETDEWEB)

    Kueper, Timothy Walter [Univ. of California, Berkeley, CA (United States)

    1992-05-01

    A process for the deposition of sol-gel derived thin films on porous substrates has been developed; such films should be useful for solid oxide fuel cells and related applications. Yttria-stabilized zirconia films have been formed from metal alkoxide starting solutions. Dense films have been deposited on metal substrates and ceramic substrates, both dense and porous, through dip-coating and spin-coating techniques, followed by a heat treatment in air. X-ray diffraction has been used to determine the crystalline phases formed and the extent of reactions with various substrates which may be encountered in gas/gas devices. Surface coatings have been successfully applied to porous substrates through the control of substrate pore size and deposition parameters. Wetting of the substrate pores by the coating solution is discussed, and conditions are defined for which films can be deposited over the pores without filling the interiors of the pores. Shrinkage cracking was encountered in films thicker than a critical value, which depended on the sol-gel process parameters and on the substrate characteristics. Local discontinuities were also observed in films which were thinner than a critical value which depended on the substrate pore size. A theoretical discussion of cracking mechanisms is presented for both types of cracking, and the conditions necessary for successful thin formation are defined. The applicability of these film gas/gas devices is discussed.

  5. Uncaria tomentosa Gel against Denture Stomatitis: Clinical Report.

    Science.gov (United States)

    Tay, Lidia Y; Dos Santos, Fabio A; Jorge, Janaina H

    2015-02-09

    The objective of this study is to report the clinical use of 2% Uncaria tomentosa gel against denture stomatitis (DS) as an alternative treatment. The patient was a 65-year-old, denture-wearing woman. At the clinical examination, her palate showed hyperplasic and erythematous mucosa indicating DS type II. DS is a chronic oral disease that affects denture wearers. It occurs as an inflammatory reaction in denture-wearing patients under maxillary prostheses. Candida albicans has been reported as the principal etiological agent. An alternative treatment, the topical application of a gel of 2% U. tomentosa three times a day for 1 week was given to the patient. After 1 week of this treatment, she had significantly reduced signs of the disease. Despite the existence of a great number of antifungal agents, treatment failure is observed frequently. Phytotherapy is becoming more popular worldwide. Currently, the most promising medicinal Amazonian herb is U. tomentosa (Willd.) DC., known as Cat's Claw. Studies of the chemical and pharmacological properties of this medicinal plant have allowed researchers to develop indications for its use. This report demonstrates the effectiveness of U. tomentosa against DS. © 2015 by the American College of Prosthodontists.

  6. Design and Development of Repaglinide Microemulsion Gel for Transdermal Delivery.

    Science.gov (United States)

    Shinde, Ujwala A; Modani, Sheela H; Singh, Kavita H

    2018-01-01

    Microemulsion formulation of repaglinide, a BCS class II hypoglycemic agent with limited oral bioavailability, was developed considering its solubility in various oils, surfactants, and cosurfactants. The pseudo-ternary phase diagrams for microemulsion regions were constructed by water titration method at K m 1:1 and characterized for optical birefringence, percentage transmittance, pH, refractive index, globule size, zeta potential, viscosity, drug content, and thermodynamic stability. To enhance the drug permeation and residence time, the optimized microemulsions having mean globule size of 36.15 ± 9.89 nm was gelled with xanthan gum. The developed microemulsion-based gel was characterized for globule size, zeta potential, pH, and drug content. All evaluation parameters upon gelling were found to be satisfactory. Ex vivo permeability study across rat skin demonstrated higher steady-state flux (P RPG) suspension. In vivo efficacy study was performed in normal Sprague-Dawley rats by using oral glucose tolerance test. Results of RPG transdermal microemulsion gel demonstrated remarkable advantage over orally administered RPG by reducing the glucose level in controlled manner. Hence, it could be a new, alternative dosage form for effective therapy of type 2 diabetes mellitus.

  7. The effects of amylose and starch phosphate on starch gel retrogradation studied by low-field 1H NMR relaxometry

    DEFF Research Database (Denmark)

    Thygesen, Lisbeth Garbrecht; Blennow, A.; Engelsen, S. B.

    2003-01-01

    Low-field Nuclear Magnetic Resonance (23 MHz) was used to study the effects of the degree of phosphorylation, the amylose content and the amylopectin chain length distribution on gel retrogradation for a set of 26 starches, six of which were of crystal polymorph type A, 18 of type B and two of type......) relaxation curves from the two measurements (day 1 and day 7) could be used as a simple, illustrative way of describing the retrogradation. Three different behaviours were identified: One group of samples (mostly potato starches) slowly changed from a soft to a more rigid gel from day 1 to 7. A second group...

  8. Optical-CT scanning of polymer gels

    International Nuclear Information System (INIS)

    Oldham, M

    2004-01-01

    The application of optical-CT scanning to achieve accurate high-resolution 3D dosimetry is a subject of current interest. The purpose of this paper is to provide a brief overview of past research and achievements in optical-CT polymer gel dosimetry, and to review current issues and challenges. The origins of optical-CT imaging of light-scattering polymer gels are reviewed. Techniques to characterize and optimize optical-CT performance are presented. Particular attention is given to studies of artifacts in optical-CT imaging, an important area that has not been well studied to date. The technique of optical-CT simulation by Monte-Carlo modeling is introduced as a tool to explore such artifacts. New simulation studies are presented and compared with experimental data

  9. Local mobility and topology in gels

    International Nuclear Information System (INIS)

    Higgins, J.S.; Ma, K.; Hall, R.H.; Warner, M.

    1981-04-01

    In the first section of this two part report entitled 'Separation of the motion around cross-link points from main chain motion in network samples' by Higgins, Ma and Hall, experimental evidence for topologically dependent diffusion in gels and rubbers is presented from high resolution neutron scattering experiments on deuterium labelled model trifunctional networks which show that the junction points move more slowly than the free chain centres by a factor of about two. In the second part by Warner entitled 'The dynamics of particular points on a polymer chain', the diffusional dynamics of particular points of a polymer chain is calculated in the Rouse approximation. The points considered correspond, in the case of incoherent neutron scattering, to the proton-labelled free ends of chains, crosslinks between chains in rubbers or gels, or the central monomers in branched or star polymers. Results derived are also relevant to NMR, ESR and computer simulation experiments. (U.K.)

  10. Solvent induced supramolecular anisotropy in molecular gels

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, Michael A., E-mail: mroger09@uoguelph.ca [Department of Food Science, University of Guelph, Guelph, Ontario, N3C3X9 (Canada); Corradini, Maria G. [Department of Food Science, University of Massachusetts Amherst, Amherst, MA, 01003 (United States); Emge, Thomas [Department of Chemistry and Biochemistry, Rutgers University, New Brunswick, NJ, 08901 (United States)

    2017-06-15

    Herein is the first report of solvent induced anisotropy in 12-hydroxystearic acid self-assembled fibrillar networks. Increasing the chain length of polar solvent, such as nitriles and ketones, tailored the anisotropy of the fibrillar aggregates. 12HSA molecular gels, comprised of alkanes, exhibited an isotropic fibrillar network irrespective of the alkane chain length. In polar solvents, anisotropy, observed using 2D powder x-ray diffraction profiles, is correlated to a fibrillar supramolecular morphologies in long chain nitriles and ketones while sphereulitic crystals are correlated to x-ray diffraction patterns with an isotropic scatter intensity in short chain ketones and nitriles. These changes directly modify the final physical properties of the gels. - Highlights: • 12-HSA self-assembles into crystalline supramolecular morphologies depending on the solvent. • Alkanes, short chain nitriles and ketones led to 12-HSA displaying supramolecular isotropy. • In long chain nitriles and ketones, 12-HSA displays supramolecular anisotropy.

  11. Solvent induced supramolecular anisotropy in molecular gels

    International Nuclear Information System (INIS)

    Rogers, Michael A.; Corradini, Maria G.; Emge, Thomas

    2017-01-01

    Herein is the first report of solvent induced anisotropy in 12-hydroxystearic acid self-assembled fibrillar networks. Increasing the chain length of polar solvent, such as nitriles and ketones, tailored the anisotropy of the fibrillar aggregates. 12HSA molecular gels, comprised of alkanes, exhibited an isotropic fibrillar network irrespective of the alkane chain length. In polar solvents, anisotropy, observed using 2D powder x-ray diffraction profiles, is correlated to a fibrillar supramolecular morphologies in long chain nitriles and ketones while sphereulitic crystals are correlated to x-ray diffraction patterns with an isotropic scatter intensity in short chain ketones and nitriles. These changes directly modify the final physical properties of the gels. - Highlights: • 12-HSA self-assembles into crystalline supramolecular morphologies depending on the solvent. • Alkanes, short chain nitriles and ketones led to 12-HSA displaying supramolecular isotropy. • In long chain nitriles and ketones, 12-HSA displays supramolecular anisotropy.

  12. Gel Evolution in Oil Based Drilling Fluids

    OpenAIRE

    Sandvold, Ida

    2012-01-01

    Drilling fluids make up an essential part of the drilling operation. Successful drilling operations rely on adequate drilling fluid quality. With the development of new drilling techniques such as long deviated sections and drilling in ultra-deep waters, the standard of required performance of the drilling fluids continue to increase. Narrow pressure margins and low tolerance for barite sag requires accurate prediction of the gel evolution in drilling fluids. Increased knowledge of how dri...

  13. Sol-Gel Chemistry for Carbon Dots.

    Science.gov (United States)

    Malfatti, Luca; Innocenzi, Plinio

    2018-03-14

    Carbon dots are an emerging class of carbon-based nanostructures produced by low-cost raw materials which exhibit a widely-tunable photoluminescence and a high quantum yield. The potential of these nanomaterials as a substitute of semiconductor quantum dots in optoelectronics and biomedicine is very high, however they need a customized chemistry to be integrated in host-guest systems or functionalized in core-shell structures. This review is focused on recent advances of the sol-gel chemistry applied to the C-dots technology. The surface modification, the fine tailoring of the chemical composition and the embedding into a complex nanostructured material are the main targets of combining sol-gel processing with C-dots chemistry. In addition, the synergistic effect of the sol-gel precursor combined with the C-dots contribute to modify the intrinsic chemo-physical properties of the dots, empowering the emission efficiency or enabling the tuning of the photoluminescence over a wide range of the visible spectrum. © 2018 The Chemical Society of Japan & Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Sol-gel bonding of silicon wafers

    International Nuclear Information System (INIS)

    Barbe, C.J.; Cassidy, D.J.; Triani, G.; Latella, B.A.; Mitchell, D.R.G.; Finnie, K.S.; Bartlett, J.R.; Woolfrey, J.L.; Collins, G.A.

    2005-01-01

    Low temperature bonding of silicon wafers was achieved using sol-gel technology. The initial sol-gel chemistry of the coating solution was found to influence the mechanical properties of the resulting bonds. More precisely, the influence of parameters such as the alkoxide concentration, water-to-alkoxide molar ratio, pH, and solution aging on the final bond morphologies and interfacial fracture energy was studied. The thickness and density of the sol-gel coating were characterised using ellipsometry. The corresponding bonded specimens were investigated using attenuated total reflectance Fourier transformed infrared spectroscopy to monitor their chemical composition, infrared imaging to control bond integrity, and cross-sectional transmission electron microscopy to study their microstructure. Their interfacial fracture energy was measured using microindentation. An optimum water-to-alkoxide molar ratio of 10 and hydrolysis water at pH = 2 were found. Such conditions led to relatively dense films (> 90%), resulting in bonds with a fracture energy of 3.5 J/m 2 , significantly higher than those obtained using classical hydrophilic bonding (typically 1.5-2.5 J/m 2 ). Ageing of the coating solution was found to decrease the bond strength

  15. Gel Electrophoresis of Gold-DNA Nanoconjugates

    Directory of Open Access Journals (Sweden)

    T. Pellegrino

    2007-01-01

    Full Text Available Gold-DNA conjugates were investigated in detail by a comprehensive gel electrophoresis study based on 1200 gels. A controlled number of single-stranded DNA of different length was attached specifically via thiol-Au bonds to phosphine-stabilized colloidal gold nanoparticles. Alternatively, the surface of the gold particles was saturated with single stranded DNA of different length either specifically via thiol-Au bonds or by nonspecific adsorption. From the experimentally determined electrophoretic mobilities, estimates for the effective diameters of the gold-DNA conjugates were derived by applying two different data treatment approaches. The first method is based on making a calibration curve for the relation between effective diameters and mobilities with gold nanoparticles of known diameter. The second method is based on Ferguson analysis which uses gold nanoparticles of known diameter as reference database. Our study shows that effective diameters derived from gel electrophoresis measurements are affected with a high error bar as the determined values strongly depend on the method of evaluation, though relative changes in size upon binding of molecules can be detected with high precision. Furthermore, in this study, the specific attachment of DNA via gold-thiol bonds to Au nanoparticles is compared to nonspecific adsorption of DNA. Also, the maximum number of DNA molecules that can be bound per particle was determined.

  16. Epoxy Sol-Gel Hybrid Thermosets

    Directory of Open Access Journals (Sweden)

    Angels Serra

    2016-02-01

    Full Text Available Sol-gel methodologies are advantageous in the preparation of hybrid materials in front of the conventional addition of nanoparticles, because of the fine dispersion of the inorganic phase that can be reached in epoxy matrices. In addition, the use of organoalkoxysilanes as coupling agents allows covalent linkage between organic and inorganic phases, which is the key point in the improvement of mechanical properties. The sol-gel process involves hydrolysis and condensation reactions under mild conditions, starting from hydrolysable metal alkoxides, generally alkoxy silanes. Using the sol-gel procedure, the viscosity of the formulation is maintained, which is an important issue in coating applications, whereas the transparency of the polymer matrix is also maintained. However, only the proper combination of the chemistries and functionalities of both organic and inorganic structures leads to thermosets with the desired characteristics. The adequate preparation of hybrid epoxy thermosets enables their improvement in characteristics such as mechanical properties (modulus, hardness, scratch resistance, thermal and flame resistance, corrosion and antimicrobial protection, and even optical performance among others.

  17. Role of gel dosimeters in boron neutron capture therapy

    International Nuclear Information System (INIS)

    Khajeali, Azim; Farajollahi, Ali Reza; Khodadadi, Roghayeh; Kasesaz, Yaser; Khalili, Assef

    2015-01-01

    Gel dosimeters have acquired a unique status in radiotherapy, especially with the advent of the new techniques in which there is a need for three-dimensional dose measurement with high spatial resolution. One of the techniques in which the use of gel dosimeters has drawn the attention of the researchers is the boron neutron capture therapy. Exploring the history of gel dosimeters, this paper sets out to study their role in the boron neutron capture therapy dosimetric process. - Highlights: • Gel dosimeters have been investigated. • Conventional dosimetric proses of BNCT has been investigated. • Role of gel dosimeters in BNCT has been investigated

  18. Species identification of cooked fish by urea isoelectric focusing and sodium dodecylsulfate polyacrylamide gel electrophoresis : a collaborative study

    DEFF Research Database (Denmark)

    Rehbein, H.; Kundiger, R.; Yman, I.M.

    1999-01-01

    of gels to be run in the same flat bed electrophoresis chamber. By strictly following optimised standard operation procedures (SOPs), five unknown cooked samples had to be identified with each technique using a set of 10 raw reference samples. With urea IEF, only one out of 35 identifications......The suitability and reliability of urea IEF and SDS-PAGE for the identification of cooked fish flesh was tested by a collaborative study among nine laboratories. Urea IEF was performed with CleanGels as well as with ImmobilineGels, and ExcelGels were used for SDS-PAGE, enabling all three types...... was incorrect, and with SDS-PAGE a similar result was obtained. It was concluded that methods, as now developed, are suitable for checking the species declaration of fishery products. (C) 1999 Elsevier Science Ltd. All rights reserved...

  19. Oxidizing gel formulation for nuclear decontamination: rheological and acidic properties of the organic matrix and its ozonolysis

    International Nuclear Information System (INIS)

    Rouy, E.

    2003-10-01

    An acidic and oxidizing gel was formulated with a purely organic matrix, xanthan gum, at low concentrations (1 to 2 wt %). This polymer gel was investigated in various media (aqueous, acidic and ceric) by means of rheology: shear thinning behaviour, thixotropy, yield stress... Evidences of unexpected rheological properties in highly concentrated media show that xanthan is quite convenient for industrial projection of this type of gel on metallic walls in nuclear plants, notwithstanding its time-limited resistance to oxidation (about a few hours). Complexation mechanisms between ceric species and polar sites of the polymer led us to characterise acidic properties of our xanthan sample by potentiometric titration and 1 H NMR techniques. The matrix was finally treated by ozonolysis to suppress organic residues, as required to handle nuclear wastes. In acidic medium, ozonolysis of the gel was achieved successfully while in acidic and ceric medium this process showed limited efficiency, needing further investigation to be clarified. (author)

  20. Colloid molecular weight estimation by gel chromatography/acrylamide gel electrophoresis

    International Nuclear Information System (INIS)

    Liberatore, F.A.; Dearborn, C.; Nigam, S.; Poon, C.; Camin, L.; Liteplo, M.

    1984-01-01

    Size or molecular weight (MW) estimation of radiolabeled collides in aqueous solutions has long been a problem. The authors have prepared several minimicroaggregated albumin colloids (mμAA) by heat denaturation of stannous-containing HSA solutions at pH 7.0, 7.5, and 8.5). The resulting colloids were labeled with Tc-99m and compared with Au-198 colloid and Tc-99m-antimony sulfide colloid (Tc-99m-Sb/sub 2/S3) by gel chromatography and gel electrophoresis. Tc-99mm-mμAA aggregated at pH 7.0 and the Au-198 colloid appeared in the external void volume of a BioRad A5.0 agarose column indicating an apparent MW of > 5 x 10/sup 6/ daltons. The pH7.5 Tc-99m-mμAA, migrated within the filtration range of the column as did a small fraction of Tc-99m-Sb/sub 2/S/sub 3/, suggesting that the MW is between 6 x 10/sup 4/ - 5 x 10/sup 6/ daltons. The Tc-99m-mμAA, aggregated at pH 8.5, had an apparent MW on gel filtration similar to that of untreated albumin, MW 6.6 x 10-/sup 4/ daltons. The mobilities of the colloids, on acrylamide disc gel electrophoresis, were consistent with the results on gel chromatography. The largest colloids, Au-198 colloid and pH 7.0 Tc-99m-mμAA, barely entered the separating gel; intermediate sized colloids, a small fraction of Tc-99m-Sb/sub 2/S/sub 3/ and pH 7.5 Tc-99m-mμAA migrated farther into the separating gel; while pH 8.5 Tc-99m-mμAA had mobility approaching that of untreated albumin. Lymphoscintigraphy studies using these colloids in animals showed the predicted, particle size-related differences in migration and clearance. The authors conclude that gel chromatography and gel electrophoresis are useful methods for estimating the apparent size of the colloidal particles

  1. Fluoride gels for preventing dental caries in children and adolescents.

    Science.gov (United States)

    Marinho, Valeria C C; Worthington, Helen V; Walsh, Tanya; Chong, Lee Yee

    2015-06-15

    children up to 16 years. The frequency of application had to be at least once a year, and study duration at least one year. The main outcome was caries increment measured by the change in decayed, missing and filled tooth surfaces in both permanent and primary teeth (D(M)FS and d(e/m)fs). At least two review authors independently performed study selection, data extraction and 'Risk of bias' assessment. We contacted study authors for additional information where required. The primary measure of effect was the prevented fraction (PF), that is, the difference in mean caries increments between the treatment and control groups expressed as a percentage of the mean increment in the control group. We performed random-effects meta-analyses where we could pool data. We examined potential sources of heterogeneity in random-effects metaregression analyses. We collected adverse effects information from the included trials. We included 28 trials (3 of which are new trials since the original review), involving 9140 children and adolescents. Most of these trials recruited participants from schools. Most of the studies (20) were at high risk of bias, with 8 at unclear risk of bias.Twenty-five trials (8479 participants) contributed data for meta-analysis on permanent tooth surfaces: the D(M)FS pooled prevented fraction (PF) estimate was 28% (95% confidence intervals (CI) 19% to 36%; P effect of fluoride gel varied according to the type of control group used, with D(M)FS PF on average being 17% (95% CI 3% to 31%; P = 0.018) higher in non-placebo-controlled trials (the reduction in caries was 38% (95% CI 24% to 52%; P effects.The d(e/m)fs pooled prevented fraction estimate for the three trials (1254 participants) that contributed data for the meta-analysis on primary teeth surfaces was 20% (95% CI 1% to 38%; P = 0.04; with no heterogeneity (P = 0.54; I(2) = 0%); low quality evidence).There was limited reporting of adverse events. Only two trials reported information on acute toxicity signs

  2. Antioxidant effect of green tea on polymer gel dosimeter

    International Nuclear Information System (INIS)

    Samuel, E J J; Sathiyaraj, P; Deena, T; Kumar, D S

    2015-01-01

    Extract from Green Tea (GTE) acts as an antioxidant in acrylamide based polymer gel dosimeter. In this work, PAGAT gel was used for investigation of antioxidant effect of GTE.PAGAT was called PAGTEG (Polyacrylamide green tea extract gel dosimeter) after adding GTE. Free radicals in water cause pre polymerization of polymer gel before irradiation. Polyphenols from GTE are highly effective to absorb the free radicals in water. THPC is used as an antioxidant in polymer gel dosimeter but here we were replaced it by GTE and investigated its effect by spectrophotometer. GTE added PAGAT samples response was lower compared to THPC added sample. To increase the sensitivity of the PAGTEG, sugar was added. This study confirmed that THPC was a good antioxidant for polymer gel dosimeter. However, GTE also can be used as an antioxidant in polymer gel if use less quantity (GTE) and add sugar as sensitivity enhancer

  3. Antioxidant effect of green tea on polymer gel dosimeter

    Science.gov (United States)

    Samuel, E. J. J.; Sathiyaraj, P.; Deena, T.; Kumar, D. S.

    2015-01-01

    Extract from Green Tea (GTE) acts as an antioxidant in acrylamide based polymer gel dosimeter. In this work, PAGAT gel was used for investigation of antioxidant effect of GTE.PAGAT was called PAGTEG (Polyacrylamide green tea extract gel dosimeter) after adding GTE. Free radicals in water cause pre polymerization of polymer gel before irradiation. Polyphenols from GTE are highly effective to absorb the free radicals in water. THPC is used as an antioxidant in polymer gel dosimeter but here we were replaced it by GTE and investigated its effect by spectrophotometer. GTE added PAGAT samples response was lower compared to THPC added sample. To increase the sensitivity of the PAGTEG, sugar was added. This study confirmed that THPC was a good antioxidant for polymer gel dosimeter. However, GTE also can be used as an antioxidant in polymer gel if use less quantity (GTE) and add sugar as sensitivity enhancer.

  4. Anion-switchable supramolecular gels for controlling pharmaceutical crystal growth

    Science.gov (United States)

    Foster, Jonathan A.; Piepenbrock, Marc-Oliver M.; Lloyd, Gareth O.; Clarke, Nigel; Howard, Judith A. K.; Steed, Jonathan W.

    2010-12-01

    We describe the use of low-molecular-weight supramolecular gels as media for the growth of molecular crystals. Growth of a range of crystals of organic compounds, including pharmaceuticals, was achieved in bis(urea) gels. Low-molecular-weight supramolecular gelators allow access to an unlimited range of solvent systems, in contrast to conventional aqueous gels such as gelatin and agarose. A detailed study of carbamazepine crystal growth in four different bis(urea) gelators, including a metallogelator, is reported. The crystallization of a range of other drug substances, namely sparfloxacin, piroxicam, theophylline, caffeine, ibuprofen, acetaminophen (paracetamol), sulindac and indomethacin, was also achieved in supramolecular gel media without co-crystal formation. In many cases, crystals can be conveniently recovered from the gels by using supramolecular anion-triggered gel dissolution; however, crystals of substances that themselves bind to anions are dissolved by them. Overall, supramolecular gel-phase crystallization offers an extremely versatile new tool in pharmaceutical polymorph screening.

  5. Different Applications of Rheological Techniques in Studies of Physical Gels

    DEFF Research Database (Denmark)

    Hvidt, Søren

    ] pointed out the importance of time scales for physical gels. According to him the characteristic property of a gel is the presence of two components and a constant elastic storage modulus on time scales of 1 s or frequencies of 1 rad/s. His definition of gels relies on their rheological properties......Physical gels are of both great scientific and practical interest. The cytoplasm of cells, which consists of a complex physical gel of protein filaments, is important for most of the cellular processes including cell division and cell motility. Nature has developed this complex system......-forming biopolymers. Physical gels are also used in the paint industry to minimize sedimentation. Delayed and controlled drug release is of importance in the pharmaceutical industry, and one way to obtain this control is to hide active components in physical gels. Two excellent reviews cover many aspects...

  6. High-strength cellulose/poly(ethylene glycol) gels.

    Science.gov (United States)

    Liang, Songmiao; Wu, Junjie; Tian, Huafeng; Zhang, Lina; Xu, Jian

    2008-01-01

    Cellulose gel membranes have been prepared by a pre-gelation method employing cellulose solutions in aqueous NaOH-thiourea obtained at low temperature. The cellulose gels were then swollen by low-molecular-weight polyethylene glycol (PEG; MWcellulose/PEG gels were studied by various techniques. The gels exhibit high mechanical performance, and the tensile strength of the gel membranes increases sharply with an increase in the molecular weight of PEG from 200 to 800 g mol(-1). Moreover, their elongation at break remains stable at 100 %. PEG800 efficiently improves the optical transmittance of the gel membranes at ambient temperature, which is about five times greater than that of a normal cellulose hydrogel membrane. A strong hydrogen-bonding interaction occurs between PEG and cellulose leading to a homogeneous structure, high mechanical strength and good transparency of the gel membranes.

  7. Agarose gel electrophoresis and polyacrylamide gel electrophoresis for visualization of simple sequence repeats.

    Science.gov (United States)

    Anderson, James; Wright, Drew; Meksem, Khalid

    2013-01-01

    In the modern age of genetic research there is a constant search for ways to improve the efficiency of plant selection. The most recent technology that can result in a highly efficient means of selection and still be done at a low cost is through plant selection directed by simple sequence repeats (SSRs or microsatellites). The molecular markers are used to select for certain desirable plant traits without relying on ambiguous phenotypic data. The best way to detect these is the use of gel electrophoresis. Gel electrophoresis is a common technique in laboratory settings which is used to separate deoxyribonucleic acid (DNA) and ribonucleic acid (RNA) by size. Loading DNA and RNA onto gels allows for visualization of the size of fragments through the separation of DNA and RNA fragments. This is achieved through the use of the charge in the particles. As the fragments separate, they form into distinct bands at set sizes. We describe the ability to visualize SSRs on slab gels of agarose and polyacrylamide gel electrophoresis.

  8. Influence of whitening gel on pulp chamber temperature rise by in-office bleaching technique

    Directory of Open Access Journals (Sweden)

    Sandro Cordeiro Loretto

    Full Text Available INTRODUCTION: Dental bleaching is a conservative method for the aesthetic restoration of stained teeth. However, whitening treatments are likely to cause adverse effects when not well planned and executed. OBJECTIVE: This study evaluated the influence of whitening gel on temperature rise in the pulp chamber, using the in-office photoactivated dental bleaching technique. MATERIAL AND METHOD: The root portion of an upper central human incisor was sectioned 3mm below the cemento-enamel junction. The root canal was enlarged to permit the insertion of the K-type thermocouple sensor (MT-401 into the pulp chamber, which was filled with thermal paste to facilitate the transfer of heat during bleaching. Three photosensitive whitening agents (35% hydrogen peroxide were used: Whiteness HP (FGM, Whiteness HP Maxx (FGM and Lase Peroxide Sensy (DMC. An LED photocuring light (Flash Lite - Discus Dental was used to activate the whitening gels. Six bleaching cycles were performed on each group tested. The results were submitted to one-way ANOVA and LSD t-test (α<0.05. RESULT: The lowest mean temperature variation (ºC was detected for Lase Peroxide Sensy (0.20, while the highest was recorded for Whiteness HP (1.50. CONCLUSION: The Whiteness HP and Whiteness HP Maxx whitening gels significantly affected the temperature rise in the pulp chamber during bleaching, and this variation was dependent on the type of whitening gel used.

  9. Haptic characterization of human skin in vivo in response to shower gels using a magnetic levitation device.

    Science.gov (United States)

    Yardley, R; Fan, A; Masters, J; Mascaro, S

    2016-02-01

    Skin products such as shower gels have a direct impact on skin health and wellness. Although qualitative haptic characterization through explicit, verbal measures in consumer studies are often sufficient for general comparison on consumer perceived skin feel, a quantitative approach is desired to characterize minute changes in skin condition in response to various skin products. Prior research has sought to characterize the haptic properties of human skin in vitro and in vivo, but very few studies have compared the haptic effects of commercial skin products having relatively similar formulations. In addition, related studies have typically utilized simple, low-precision devices and fixtures. The purpose of this study was to use a precision magnetic levitation haptic device to characterize the frictional properties of human skin in vivo before, during, and after treatment with commercially available shower gels, to capture the entire cycle of consumer experience on skin feel. A hybrid force-position control algorithm was used to control a precision magnetic levitation haptic device with silicone tactor to stroke the human skin (on the volar forearm) in vivo. Position and force data were collected from 32 human subjects using eight different commercially available shower gels, while stroking the skin before, during, and after treatment. The data were analyzed to produce coefficients of friction and viscous damping constant, which were used as metrics for comparing the effects of each shower gel type. Other factors investigated include skin test location, order, and subject age and gender. Results showed significant differences between the effects of eight various shower gels, especially after accounting for variance between subjects. Most notably, Shower Gel four with high level of petrolatum, along with Shower Gels five and six with low levels of castoryl maleate (a skin lipid analog), as well as Shower Gel two with high levels of vegetable oils yielded higher skin

  10. In vitro release of dibucaine hydrochloride from chitosan semisolid vehicles: emulsion and hydrophilic gels

    Directory of Open Access Journals (Sweden)

    Nilia de la Paz

    2017-04-01

    Full Text Available Context: Chitosan has received attention as a functional, sustainably renewable, nontoxic and biodegradable biopolymer for pharmaceutical applications. Aims: To evaluate the release of dibucaine hydrochloride from semisolid vehicles of oil/aqueous type emulsion and aqueous gels, stabilized by using chitosan (CH or chitosan acetate (CHAc. Methods: Emulsions were developed by varying the emulsifying agent: polysorbate 80, CH or CHAc and by combining CH with polysorbate 80 or CHAc with polysorbate 80. The hydroxypropylmethyl cellulose F4M was added as a stabilizing agent in gel formulations. The release rates of model drug from semisolid vehicles were measured by using a dialysis sac. Drug release was also quantified by using a validated UV-VIS spectrophotometric method. Results: The pH values showed minimal changes for emulsion and gel formulations. The drug is a cationic salt, and it is not able to bind polymer cations by electrostatic repulsion. The rheological property of the vehicle type emulsion was adjusted to plastic and pseudo-plastic fluid to the gels. The drug release was independent of the viscosity of vehicles. Dibucaine release from both types of formulation was found to follow a square-root-of-time kinetic model, but a higher rate of release was obtained from gel formulations. Conclusions: It was shown that chitosan was adsorbed to the surface of polysorbate 80-coated droplets, and that the electrostatic attraction between the non-ionic surfactant and the drug retarded its release from a semisolid system. The multilayer emulsions showed more influence of the release of drug than CH or CHAc single layer emulsion.

  11. Data on DNA gel sample load, gel electrophoresis, PCR and cost analysis

    Directory of Open Access Journals (Sweden)

    Ramona Kuhn

    2018-02-01

    Full Text Available The data presented in this article provide supporting information to the related research article “Comparison of ten different DNA extraction procedures with respect to their suitability for environmental samples” (Kuhn et al., 2017 [1]. In that article, we compared the suitability of ten selected DNA extraction methods based on DNA quality, purity, quantity and applicability to universal PCR. Here we provide the data on the specific DNA gel sample load, all unreported gel images of crude DNA and PCR results, and the complete cost analysis for all tested extraction procedures and in addition two commercial DNA extraction kits for soil and water. Keywords: Cost analysis, DNA sample load, Gel electrophoresis

  12. Sol-gel synthesis of hydroxyapatite; Sintese de hidroxiapatita via sol-gel

    Energy Technology Data Exchange (ETDEWEB)

    Zupanski, M.D.; Lucena, M.P.P.; Bergmann, C.P., E-mail: michelledunin@yahoo.com.b [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil)

    2010-07-01

    Hydroxyapatite (HAp) has been established as the calcium phosphate based compound with most applications in the biological field. Among the numerous techniques for synthesis of HAp, the sol-gel processing route affords great control over purity and formed phases using low processing temperatures. In addition, the sol-gel approach offers an option for homogeneous HAp coating on metal substrates, as well as the ability to generate nanocrystalline powders. In this work, the sol-gel synthesis of HAp was investigated employing triethyl phosphate and calcium nitrate tetrahydrate as phosphorous and calcium precursors, respectively. The aging effect on phase composition and powder morphology of the final product was studied in terms of temperature and aging time. The powders were studied by using X-ray diffraction, Fourier transform infrared spectroscopy, particle size distribution by laser diffraction and scanning electron microscopy. (author)

  13. Cylindrical agar gel with fluid flow subjected to an alternating magnetic field during hyperthermia.

    Science.gov (United States)

    Javidi, Mehrdad; Heydari, Morteza; Attar, Mohammad Mahdi; Haghpanahi, Mohammad; Karimi, Alireza; Navidbakhsh, Mahdi; Amanpour, Saeid

    2015-02-01

    In magnetic fluid hyperthermia (MFH), nanoparticles are injected into diseased tissue and subjected to an alternating high frequency magnetic field. The process triggers sufficient heat to destroy the cancerous cells. One of the challenging problems during MFH is blood flow in tissue. In real conditions the heat which is transferred by blood flow should be considered in the analysis of MFH. In this study, heat transfer was investigated in an agar gel phantom containing fluid flow. Fe3O4 as a nano-fluid was injected into the centre of a gel cylinder which was filled with another gel cylinder and subjected to an alternating magnetic field of 7.3 kA/m and a frequency of 50 kHz for 3600 s. The temperature was measured at three points in the gel. Temperature distributions regarding the time at these three points were experimentally measured. Moreover, the specific absorption rate (SAR) function was calculated with a temperature function. The SAR function was a key asset in the hyperthermia and was obtained on the condition that the fluid flowed through the gel. Finally, a finite element analysis (FEA) was performed to verify the SAR function. The results revealed that there was good agreement between the measured temperature and the one obtained from FEA. In addition, the effects of fluid flow and accuracy of function obtained for heat production in the gel were presented. It is believed that the proposed model has the potential ability to get close to reality in this type of investigation. The proposed function has implications for use in further modelling studies as a heat generation source.

  14. Gel pillow designed specifically for obstructive sleep apnea treatment with continuous positive airway pressure

    Directory of Open Access Journals (Sweden)

    Adriana Salvaggio

    Full Text Available ABSTRACT Objective: To determine whether the use of a gel pillow with side cutouts designed to accommodate a continuous positive airway pressure (CPAP mask and reduce head temperature improves the efficacy of and adherence to auto-CPAP therapy. Methods: Twenty-three consecutive CPAP-naïve patients with obstructive sleep apnea were enrolled in the study. Patients were given an auto-CPAP machine with an appropriate CPAP mask and were instructed to use CPAP for 15 nights. They were instructed to sleep with their own pillow (the control pillow from nights 1 to 5 and with either a foam pillow or a gel pillow, both of which had side cutouts, for 5 consecutive nights each, in random order. After night 15, auto-CPAP machine data were downloaded and patients rated their satisfaction with each pillow on a visual analog scale. Results: Twenty-two patients completed the protocol. The pressures administered, residual apnea-hypopnea index, air leaks, and mean duration of CPAP use did not differ among the periods during which each pillow was used. Patients were significantly more satisfied with the gel pillow than with the control pillow and the foam pillow (p = 0.022 and p = 0.004, respectively, their level of satisfaction with the gel pillow correlating significantly with excessive daytime sleepiness (r2 = 0.19; p = 0.0443. Conclusions: Among obstructive sleep apnea patients treated with nasal CPAP, the use of a gel pillow with side cutouts appears to have no impact on treatment effectiveness. Nevertheless, such patients seem to prefer a gel pillow over other types of pillows.

  15. ANALISA DAYA SERAP SILIKA GEL BERBAHAN DASAR ABU SEKAM PADI

    Directory of Open Access Journals (Sweden)

    Hendriwan Fahmi

    2016-08-01

    Full Text Available Rice husk ash Silica Gel is aproduct which call be used in preventing the humidity by absorbing the water ion on the water andonthe air. This absorbing isbased onthe size, the composition and the total amount ofpolluter which contained on the Silica Gel. The purpose of making this silica gel is to seehow much thiskind of Silica Gel can absorb and compare it to the synthetic one,and also processing rise husk ashto be something useful, Ion water can be absorbed much more by using this natural silica gel if it is compared to the synthetic silica gel. This is because of its capable inabsorbing more –OHand O from water and air. Afterdoing a research with column method, silica gel was beingput in 50 ml water. Fromthis research, natural silica can absorb much more water (0.0010 gr/ml, 0.285 % water level ofweigh in comparing with synthetic one (0.008gr/ml with 0.248 %water level ofweight andsintering (0,007 gr/ml 0.253%water level and non-sintering silica gel contains 39.22 % weight of silica, 30.93 %weight of sintering silica gel, and 33.40 % of the synthetic. More silica and water level, means more total amount of absorbing. This silica gel application is considered with capability ofabsorbing andthe level of the water.

  16. Photo-induced locomotion of chemo-responsive polymer gels

    Science.gov (United States)

    Dayal, Pratyush; Kuksenok, Olga; Balazs, Anna C.

    2009-03-01

    The need to translate chemical energy into a mechanical response, a characteristic of many biological processes, has motivated the study of stimuli-responsive polymer gels. Recently, it has been shown experimentally that by coupling the mechanical properties of the gel with the Belousov-Zhabotinsky (BZ) reaction it is possible to induce self-sustained oscillations in the gel. One of the means for controlling these chemical oscillations is using light as an external stimulus. To study the effect of light on the mechanical behavior of the gel, we use our recently developed a 3D gel lattice spring model (gLSM) which couples the BZ reaction kinetics to the gel dynamics. In this model, the polymer-solvent interactions were taken into account by adding a coupling term to the Flory-Huggins free energy. By virtue of this coupling term, the swelling---de-swelling behavior of the gel was captured in 3D. In order to include the effect of the polymer on the reaction kinetics, the Oregonator model for the photo-sensitive BZ reaction was also modified. Using gLSM model, we probed the effect of non-uniform light irradiation on the gel dynamics. We were able to manipulate the direction and velocity of locomotion of the gel using light as a control parameter. This ability to control the movement of the gel can be utilized in a variety of applications, ranging from bio-actuators to controlled drug release systems.

  17. RNA purification by preparative polyacrylamide gel electrophoresis.

    Science.gov (United States)

    Petrov, Alexey; Wu, Tinghe; Puglisi, Elisabetta Viani; Puglisi, Joseph D

    2013-01-01

    Preparative polyacrylamide gel electrophoresis (PAGE) is a powerful tool for purifying RNA samples. Denaturing PAGE allows separation of nucleic acids that differ by a single nucleotide in length. It is commonly used to separate and purify RNA species after in vitro transcription, to purify naturally occurring RNA variants such as tRNAs, to remove degradation products, and to purify labeled RNA species. To preserve RNA integrity following purification, RNA is usually visualized by UV shadowing or stained with ethidium bromide or SYBR green dyes. © 2013 Elsevier Inc. All rights reserved.

  18. Industrial applications of sol-gel technology

    International Nuclear Information System (INIS)

    Tuloch, S.M.; Tulloch, G.E.

    1995-01-01

    The purpose of this paper has been to provide a broad, rather than comprehensive view. We have presented a range of applications and only a selection of involved companies and researchers and have relied to a large extent on published information. Nevertheless, we are sure that our view of the importance of Sol-gel technology as an emerging technology, with enormous impact across a wide range of manufacturing, is demonstrated. Applications which are either in production or have been foreshadowed include four broad categories: coatings, fibres, powders and monoliths

  19. Separation and recovery of nucleic acids with improved biological activity by acid-degradable polyacrylamide gel electrophoresis.

    Science.gov (United States)

    Kim, Yoon Kyung; Kwon, Young Jik

    2010-05-01

    One of the fundamental challenges in studying biomacromolecules (e.g. nucleic acids and proteins) and their complexes in a biological system is isolating them in their structurally and functionally intact forms. Electrophoresis offers convenient and efficient separation and analysis of biomacromolecules but recovery of separated biomacromolecules is a significant challenge. In this study, DNAs of various sizes were separated by electrophoresis in an acid-degradable polyacrylamide gel. Almost 100% of the nucleic acids were recovered after the identified gel bands were hydrolyzed under a mildly acidic condition and purified using anion exchange resin. Further concentration by centrifugal filtration and a second purification using ion exchange column chromatography yielded 44-84% of DNA. The second conventional (non-degradable) gel electrophoresis confirmed that the nucleic acids recovered from acid-degradable gel bands preserved their electrophoretic properties through acidic gel hydrolysis, purification, and concentration processes. The plasmid DNA recovered from acid-degradable gel transfected cells significantly more efficiently than the starting plasmid DNA (i.e. improved biological activity via acid-degradable PAGE). Separation of other types of nucleic acids such as small interfering RNA using this convenient and efficient technique was also demonstrated.

  20. Fibrin gels loaded with cisplatin and cisplatin-hyaluronate complexes tested in a subcutaneous human melanoma model.

    Science.gov (United States)

    Viale, Maurizio; Rossi, Marta; Russo, Eleonora; Cilli, Michele; Aprile, Anna; Profumo, Aldo; Santi, Pierluigi; Fenoglio, Carla; Cafaggi, Sergio; Rocco, Mattia

    2015-12-01

    Fibrin gels are attractive biomaterials for local delivery of a variety of agents, from drugs to proteins. Similarly, polymer-anticancer-drug conjugates and nanoparticles are emerging as potential candidates for cancer treatment. Combining these different approaches, we have studied the efficacy of fibrin gels loaded with cisplatin (DDP) and a complex of DDP with hyaluronate (DDP-HA) for tumor growth inhibition in a melanoma model. Loaded gels prepared at relatively high fibrinogen concentration (22 mg/ml) showed good in vitro antiproliferative activities, prolonged release of the anticancer drug, and a long persistence (10-15 days) in vivo when implanted subcutaneously (sc) in immunodeficient mice. Gels loaded with DDP or DDP-HA containing 1/3 or even 1/6 of their systemic dose (6 mg/kg) and positioned under the tumor mass in mice bearing a sc human SK-Mel-28 tumor showed an antitumor activity better than that of the original parent compound given intraperitoneally (ip). Moreover, in an additional experiment in vivo, fibrin gels loaded with N-trimethyl chitosan-based nanoparticles containing a DDP-HA complex were assayed, resulting in a further 8 % improvement of anticancer activity, with lesser adverse systemic toxic effects. Taken together, these results suggest that the combination of fibrin gels and drugs complexed with suitable macromolecules holds great promise for loco-regional anticancer therapy of melanoma and other surgically removable cancer types.

  1. Natural gum modified emulsion gel as single carrier for the oral delivery of probiotic-drug combination.

    Science.gov (United States)

    Pandey, S; Senthilguru, K; Uvanesh, K; Sagiri, S S; Behera, B; Babu, N; Bhattacharyya, M K; Pal, K; Banerjee, I

    2016-11-01

    Single formulation based delivery of probiotic-drug combination is envisioned as a superior therapeutic delivery modality for the diseases like Crohn's diseases, ulceritive colitis and Recurrent Clostridium difficile-Associated Diarrhoea (RCDAD). Keeping this perspective in mind, here we have developed natural gum [using a combination of aqueous solution of xantham gum (X) and guar gum (G)] modified sunflower oil based emulsion gels for the delivery of probiotics-drugs combination. FT-IR analysis and fluorescence microscopy together confirmed the formation of oil-in-water type emulsion gel by physical gelation in presence of the physical gelator sorbitan monopalmitate (SM). Other studies (XRD, DSC, mechanical properties and disintegration study) revealed that the variation in relative proportion of the two gums has a sporadic but significant effect on the physico-chemical properties of the gel. Post storage viability of commercially used probiotic Lactobacillus plantarum 299v (Lp 299v) at different storage conditions (4°C, -20°C, -196°C) was found higher in the emulsion gels with respect to the control. Moreover, the gels were found suitable for sustained delivery of metronidazole (the lipophilic drug often used with Lp 299v). In conclusion, the natural gum modified emulsion gel may be used as a delivery system for the probiotic-drug combination. Copyright © 2016 Elsevier B.V. All rights reserved.

  2. Sensitivity calibration procedures in optical-CT scanning of BANG 3 polymer gel dosimeters

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Y.; Wuu, Cheng-Shie; Maryanski, Marek J. [Department of Radiation Oncology, Columbia University, New York, New York 10032 (United States); Department of Radiation Oncology, Columbia University, New York, New York 10032 and MGS Research Inc., Madison, Connecticut 06443 (United States)

    2010-02-15

    The dose response of the BANG 3 polymer gel dosimeter (MGS Research Inc., Madison, CT) was studied using the OCTOPUS laser CT scanner (MGS Research Inc., Madison, CT). Six 17 cm diameter and 12 cm high Barex cylinders, and 18 small glass vials were used to house the gel. The gel phantoms were irradiated with 6 and 10 MV photons, as well as 12 and 16 MeV electrons using a Varian Clinac 2100EX. Three calibration methods were used to obtain the dose response curves: (a) Optical density measurements on the 18 glass vials irradiated with graded doses from 0 to 4 Gy using 6 or 10 MV large field irradiations; (b) optical-CT scanning of Barex cylinders irradiated with graded doses (0.5, 1, 1.5, and 2 Gy) from four adjacent 4x4 cm{sup 2} photon fields or 6x6 cm{sup 2} electron fields; and (c) percent depth dose (PDD) comparison of optical-CT scans with ion chamber measurements for 6x6 cm{sup 2}, 12 and 16 MeV electron fields. The dose response of the BANG 3 gel was found to be linear and energy independent within the uncertainties of the experimental methods (about 3%). The slopes of the linearly fitted dose response curves (dose sensitivities) from the four field irradiations (0.0752{+-}3%, 0.0756{+-}3%, 0.0767{+-}3%, and 0.0759{+-}3% cm{sup -1} Gy{sup -1}) and the PDD matching methods (0.0768{+-}3% and 0.0761{+-}3% cm{sup -1} Gy{sup -1}) agree within 2.2%, indicating a good reproducibility of the gel dose response within phantoms of the same geometry. The dose sensitivities from the glass vial approach are different from those of the cylindrical Barex phantoms by more than 30%, owing probably to the difference in temperature inside the two types of phantoms during gel formation and irradiation, and possible oxygen contamination of the glass vial walls. The dose response curve obtained from the PDD matching approach with 16 MeV electron field was used to calibrate the gel phantom irradiated with the 12 MeV, 6x6 cm{sup 2} electron field. Three-dimensional dose distributions

  3. Cumulative irritation potential of metronidazole gel compared to azelaic acid gel after repeated applications to healthy skin.

    Science.gov (United States)

    Ziel, Kristin; Yelverton, Christopher B; Balkrishnan, Rajesh; Feldman, Steven R

    2005-01-01

    Metronidazole 0.75% gel and azelaic acid 15% gel are commonly used to treat rosacea. Irritation is a common side effect. To assess the cumulative irritation potential of metronidazole 0.75% gel and azelaic acid 15% gel. Metronidazole 0.75% gel, azelaic acid 15% gel, and a white petrolatum negative control were applied under occlusive conditions to the upper back of a total of 33 healthy subjects. There were twelve 24-hour applications (4 times a week) and three 72-hour applications on weekends during a 3-week period. Skin reactions (erythema score +/- other local reaction) were assessed within 15 to 30 minutes of removal of the products. The mean cumulative irritancy index of metronidazole 0.75% gel was significantly lower than that of azelaic acid 15% gel and not significantly higher than the negative control product. There was increasing cumulative irritancy with azelaic acid; no cumulative irritancy was seen for either metronidazole or white petrolatum. Metronidazole 0.75% gel is less irritating in sustained use than azelaic acid 15% gel.

  4. Gel-sphere-pac reactor fuel fabrication and its application to a variety of fuels

    International Nuclear Information System (INIS)

    Olsen, A.R.; Judkins, R.R.

    1979-12-01

    The gel-sphere-pac fuel fabrication option was evaluated for its possible application to commercial scale fuel fabrication for 19 fuel element designs that use oxide fuel in metal clad rods. The dry gel spheres are prepared at the reprocessing plant and are then calcined, sintered, inspected, and loaded into fuel rods and packed by low-energy vibration. A fuel smear density of 83 to 88% theoretical can be obtained. All fuel fabrication process steps were defined and evaluated from fuel receiving to finished fuel element shipping. The evaluation also covers the feasibility of the process, the current status of technology, estimates of the required time and cost to develop the technology to commercial status, and the safety and licensability of commercial scale plants. The primary evaluation was for a Light-Water Reactor fuel element containing (U,Pu)O 2 fuel. The other 18 fuel element types - 3 for Light-Water Reactors, 1 for a Heavy-Water Reactor, 1 for a Gas-Cooled Fast Reactor, 7 for Liquid-Metal-Cooled Fast Breeder Reactors, and 3 pairs for Light-Water Prebreeder and Breeder Reactors - were compared with the Light-Water Reactor. The gel-sphere-pac option was found applicable to 17 of the 19 element types; the characteristics of a commercial scale plant were defined for these for making cost estimates for such plants. The evaluation clearly shows the gel-sphere-pac process to be a viable fuel fabrication option. Estimates indicate a significant potential fabrication cost advantage for the gel-sphere-pac process if a remotely operated and remotely maintained fuel fabrication plant is required

  5. Investigating potential physicochemical errors in polymer gel dosimeters

    International Nuclear Information System (INIS)

    Sedaghat, Mahbod; Lepage, Martin; Bujold, Rachel

    2011-01-01

    Measurement errors in polymer gel dosimetry can originate either during irradiation or scanning. One concern related to the exothermic nature of polymerization reaction was that the heat released in polymer gel dosimeters during irradiation modifies their dose response. In this paper, the effect of heat released from the exothermal polymerization reaction on the dose response of a number of dosimeters was studied. In addition, we investigated whether heat-generated geometric distortion existed in newly proposed gel dosimeters that contain highly thermoresponsive polymers. Our results suggest that despite a significant internal temperature increase in some gel compositions, their dose responses are not affected when oxygen is well expelled mechanically from the gel mixture. We also report on significant pre-irradiation instability in some recently developed polymer gel dosimeters but that geometric distortions were not observed. Data obtained by a set of small calibration vials are compared to those obtained from larger phantoms, and potential physicochemical causes of deviations between them are identified.

  6. Detection of Aspartic Proteinase Activities Using Gel Zymography.

    Science.gov (United States)

    Perera, Handunge Kumudu Irani

    2017-01-01

    Gel zymography is a two-stage process where the proteins from the test sample are first separated by electrophoresis followed by the detection of the activity of hydrolytic enzymes. Many zymography procedures use sodium dodecyl sulfate (SDS) polyacrylamide gels copolymerized with an appropriate substrate. The procedure described here uses native polyacrylamide gel electrophoresis (PAGE) in the absence of both SDS and substrate. In order to visualize aspartic proteinase activity, the gel is impregnated in bovine hemoglobin at pH 3.0 for 15 min after the electrophoresis procedure. Subsequently, the gel is incubated in a humid container in the absence of hemoglobin for 1 h at 37 °C. At the end, the gel is stained with amido black and destained. Clear areas against a dark background corresponding to aspartic proteinase activities can be detected.

  7. Explorative data analysis of two-dimensional electrophoresis gels

    DEFF Research Database (Denmark)

    Schultz, J.; Gottlieb, D.M.; Petersen, Marianne Kjerstine

    2004-01-01

    Methods for classification of two-dimensional (2-DE) electrophoresis gels based on multivariate data analysis are demonstrated. Two-dimensional gels of ten wheat varieties are analyzed and it is demonstrated how to classify the wheat varieties in two qualities and a method for initial screening...... of gels is presented. First, an approach is demonstrated in which no prior knowledge of the separated proteins is used. Alignment of the gels followed by a simple transformation of data makes it possible to analyze the gels in an automated explorative manner by principal component analysis, to determine...... if the gels should be further analyzed. A more detailed approach is done by analyzing spot volume lists by principal components analysis and partial least square regression. The use of spot volume data offers a mean to investigate the spot pattern and link the classified protein patterns to distinct spots...

  8. Non-stationary heat transfer in gels applied to biotehnology

    Directory of Open Access Journals (Sweden)

    Pokusaev Boris

    2017-01-01

    Full Text Available Unsteady heat transfer in agarose gels of various concentrations was studied in order to make a breakthrough in the technology of 3-D additive bioprinting. Data on the kinetics of the phase transformation was obtained using spectroscopy as a function of temperature during the formation of agarose hydrogel. The dynamics of aging was investigated for gels of different densities. The time dependence of the structural changes was obtained. Particular attention was paid to the changes in the structure of the gel due to the processes of evaporation of the liquid during the gel formation and during long-term storage. Experiments were performed to determine the dynamics of the temperature fields simultaneously with heat flux measurements during the formation of agarose gels from different initial concentrations. A technique based on experimental data for the computations of the thermophysical coefficients of agarose gels was developed.

  9. Evaluations of osteogenic and osteoconductive properties of a non-woven silica gel fabric made by the electrospinning method.

    Science.gov (United States)

    Kang, Young-Mi; Kim, Kyoung-Hwa; Seol, Yang-Jo; Rhee, Sang-Hoon

    2009-01-01

    Evaluations of the osteoblast-like cell responses and osteoconductivity of a non-woven silica gel fabric were carried out to determine its potential for application as a scaffold material for use in bone tissue engineering. The silica gel solution was prepared by condensation following hydrolysis of tetraethyl orthosilicate under acidic conditions. The solution was spun under a 2kVcm(-1) electric field. The diameters of the as-spun silica gel fibers were in the range of approximately 0.7-6microm. The fabric was then heat-treated at 300 degrees C for 3h. The proliferation of pre-osteoblastic MC3T3-E1 cells evaluated by the MTS assay was lower than on the tissue culture plate (TCP) as many cells leaked through the large voids formed by the randomly placed long, narrow silica gel fibers, which further retarded cell growth. However, the expressions of extracellular signal-regulated kinase and transcriptional factor from the cells were higher when cultured on the non-woven silica gel fabrics than on TCP. The alkaline phosphatase (ALP) activity and differentiation marker expressions assessed by amplication via the reverse transcription-polymerase chain reaction, such as type I collagen, ALP and osteocalcin, were higher for cells cultured on non-woven silica gel fabrics than on TCP. The non-woven silica gel fabric showed good osteoconductivity in the calvarial defect New Zealand white rabbit model. To this end, the non-woven silica gel fabric has good potential as a scaffold material for bone tissue engineering due to its good biological properties.

  10. Intrathecal Delivery of Ketorolac Loaded In Situ Gels for Prolonged ...

    African Journals Online (AJOL)

    Further, KT-loaded gels exhibited viscosity in the range of 1.11 to 6 cps at 50 rpm and shear thinning property (rheology testing). Additionally, the gels demonstrated 84.43 to 96.98 % drug release at the end of 12 h. In particular, in situ gels prepared from 1.2 % alginate/0.4 % HPMC (G7) exhibited excellent analgesic (54.28 ...

  11. A novel quantification method for low-density gel dosimeter.

    Science.gov (United States)

    Nedaie, Hasan Ali; Pak, Farideh; Vaezzadeh, Vahid; Eqlimi, Ehsan; Takavar, Abas; Saligheh Rad, Hamid Reza; Mosleh Shirazi, Mohammad Amin; Mirheydari, Mona

    2018-01-01

    Low signal-to-noise ratio (SNR) images of lung-like (low-density [LD]) gel dosimeters, compared to unit-density (UD) gels, necessitate the use of different quantification methods. In this study, a new method is introduced based on noise correction and exponential (NCEXP) fitting. The feasibility of NCEXP method for quantifying dose absorption in LD gels is evaluated. Sensitivity, dose resolution, detectable dynamic range, and correlation of the calibration curve for both UD and LD gel dosimeters are the parameters, which we analyze to investigate the consequences of new method. Results of NCEXP method are compared to maximum likelihood estimation of rician distribution (MLE-R) and variable echo number (VAREC) quantification methods. Dose response of LD gel dosimeter shows wider detectable dynamic range as compared to UD gel. Using NCEXP method for both LD and UD dosimeter gels, a more sensitive calibration curve with a superior dose resolution is obtained. The advantage of new quantification method is more significant for LD dosimeter gel analysis, where SNR decreases as a result of higher absorbed doses (≥10 Gy). Despite the inverse effect of the VAREC method on detectable dose range of UD gel, no specific changes are observed in dynamic dose range of LD gel dosimeter with different quantification methods. The correlations obtained with different methods were approximately of the same order for UD and LD gels. NCEXP method seems to be more effective than the MLE-R and VAREC methods for quantification of LD dosimeter gel, especially where high-dose absorption and steep-dose gradients exist such as those in intensity-modulated radiation therapy and stereotactic radiosurgery.

  12. Purification of radiolabeled RNA products using denaturing gel electrophoresis

    OpenAIRE

    Adachi, Hironori; Yu, Yi-Tao

    2014-01-01

    This unit discusses a basic method for purification of radiolabeled RNAs using denaturing polyacrylamide gel electrophoresis. The method consists of a number of experimental procedures, including total RNA preparation from yeast cells, isolation of a specific RNA from total yeast RNA, RNA 3' terminal labeling using nucleotide (5’[32P]pCp) addition (via ligation), denaturing (8 M urea) polyacrylamide gel electrophoresis, and RNA extraction from the gel slice. Key points for achieving good elec...

  13. Prenatal Virilization Associated with Paternal Testosterone Gel Therapy

    OpenAIRE

    Rivkees ScottA; Patel Anisha

    2010-01-01

    Transdermal testosterone gels are used in the treatment of hypoandrogenism of males. Virilization due to exposure to testosterone gels has been reported in children resulting in a US Food and Drug Administration (FDA) warning about secondary exposure to these products. At present, we are unaware of prenatal virilization associated with unintentional testosterone gel exposure. We report prenatal virilization in a female infant due to secondary maternal exposure to the father's testosterone ge...

  14. Formulation and evaluation of antipsoriatic gel using natural excipients

    OpenAIRE

    Raghupatruni Jhansi Laxmi; R. Karthikeyan; P. Srinivasa Babu; R.V.V. Narendra Babu

    2013-01-01

    Objective: To develop topical gel formulations of Psoralen using natural excipients to minimize the side effects of synthetic drugs. Methods: The Psoralen gel formulations were prepared using different natural gums and polymers. The physicochemical compatibility between Psoralen and other excipients was confirmed by using Fourier transform infrared spectroscopy. All prepared gel formulations were evaluated for drug content uniformity, viscosity, pH, and stability. The release of psoralen f...

  15. Capillary gel electrophoresis for rapid, high resolution DNA sequencing.

    OpenAIRE

    Swerdlow, H; Gesteland, R

    1990-01-01

    Capillary gel electrophoresis has been demonstrated for the separation and detection of DNA sequencing samples. Enzymatic dideoxy nucleotide chain termination was employed, using fluorescently tagged oligonucleotide primers and laser based on-column detection (limit of detection is 6,000 molecules per peak). Capillary gel separations were shown to be three times faster, with better resolution (2.4 x), and higher separation efficiency (5.4 x) than a conventional automated slab gel DNA sequenci...

  16. Pelepasan Ibuprofen Dari Gel Karbomer 940 Kokristal Ibuprofen-Nikotinamida

    OpenAIRE

    Agustin, Rini; Sari, Novica; Zaini, Erizal

    2014-01-01

    Salah satu metode untuk meningkatkan kelarutan adalah co-kristalisasi. Ibuprofen dapat digunakan dalam aplikasi topikal untuk rheumatoid arthrisi, sehingga telah dilakukan sebuah studi tentang formulasi dan pelepasan kokristal ibuprofen-nikotinamida dari gel karbomer 940. Kokristal diperoleh dari metode penguapan pelarut dengan komposisi equimol (1:1). Gel terdiri dari dua formula dengan jumlah ibuprofen yang sama (5%). Formula pertama adalah gel kokristal ibuprofen-nicotinamida dan Formula d...

  17. Investigation into response characteristics of the chitosan gel artificial muscle

    Science.gov (United States)

    Zhao, Gang; Yang, Junjie; Wang, Yujian; Zhao, Honghao; Fu, Yu; Zhang, Guangli; Yu, Shuqin; Wu, Yuda; Wei, Chengye; Liu, Xuxiong; Wang, Zhijie

    2018-01-01

    Bionic artificial muscle made from chitosan gel is an emerging type of the ionic electro active polymer with advantages of large deformation, low cost and environmental protection etc, which leads to a research focus and wide application in the fields of bionic engineering and intelligence material recently. In this paper, effects and improvement mechanisms of the direct casting and genipin cross-linking processes on response speed properties of the chitosan gel artificial muscle (CGAM) were mainly studied. Based on in-depth analysis of the CGAM response mechanism, a platform was built for testing the response performance of the CGAM, then its equivalent circuit and mathematical models were also established. Furthermore, control experiments were carried out to test and analyze several performances of the CGAM on response speed, electrical conductivity, mechanical properties and microstructure with different control variables. The experimental results illustrated that the CGAM assembled by direct casting enabled its electric actuating membrane and non-metallic electrode membrane tightly attached together with low contact resistance, which dramatically promoted the electrical conductivity of the CGAM resulting in nearly doubled response speed. Besides, different concentrations of genipin were adopted to cross-link the CGAM actuating membranes, and then it was found that the response speed of the uncross-linked CGAM was fast in the initial stage, but as time increased, it declined rapidly with poor steadiness. While there was no obvious decrease over time on the response speed of the CGAM cross-linked with low genipin concentration. Namely, its stability was getting better and better. In addition, the response speed of the CGAM cross-linked with low concentration of genipin was roughly the same as uncross-linked CGAM, which was quicker than that of high concentration. In this work, its internal mechanisms, feasible assembly technique and green modification method were

  18. Genetic heterogeneity of Campylobacter concisus determined by pulsed field gel electrophoresis-based macrorestriction profiling

    DEFF Research Database (Denmark)

    Matsheka, M.I.; Elisha, B.G.; Lastovica, A.L.

    2002-01-01

    1 for pulsed field gel electrophoresis-based genotyping. Subsequently, 53 strains of C concisus, principally from cases of diarrhoea in children, were examined. Fifty-one distinct patterns were obtained, indicating the high discriminatory potential of the method. Patterns comprised between one...... comprised of several genomospecies. The pulsed field gel electrophoresis typing method described here has considerable potential for molecular epidemiological studies of C concisus and may be a useful adjunctive method for helping to resolve key taxonomic issues for this species....... and 14 restriction fragments, with type and reference strains of two well-defined genomospecies of oral and faecal origin containing six and 12 fragments respectively. Our results show that C concisus is genetically diverse and suggest the species as currently defined to be a taxonomic continuum...

  19. Gel-test: interpretation and value of a new technique for the detection of irregular antibodies.

    Science.gov (United States)

    Pottier, C; Quillet, P; Baufine-Ducrocq, H

    1992-01-01

    Here we report on our experience with the use of a 'Gel-Test' (DiaMed-ID Micro Typing System) technique for the detection and identification of irregular antibodies in a general hospital. This easy-to-use, standardized technique poses the question of the impact of its sensitivity on the specificity of the results. Of the 10% of observed positive reactions, 3.7% were irregular antibodies, 3.8% papain auto-antibodies, 1% cold antibodies and 2% not elucidated. Two hundred and eighteen irregular antibodies identified and titred with the 'gel-test' system were tested in parallel by 'tube' method. Sixty-three of these antibodies (29%) were not detected by the 'tube' method. While anti-Kell was always detected by both methods, we found the following false natives with the tube method: 15% anti-D, 32% anti-E, 42% anti-Cw and 58% anti-Lea. 68% of these false negatives had a low titre. The immunoglobulin class of the anti-E was studied; the sensitivity of the 'gel-test' system was associated with IgM in the anti-E. The sensitivity and standardization of the 'gel-test' technique guarantee greater safety in blood transfusion and increase efficiency in the prevention of foeto-maternal stimulation of anti-D.

  20. Chitosan gel-embedded moxifloxacin niosomes: An efficient antimicrobial hybrid system for burn infection.

    Science.gov (United States)

    Sohrabi, Shohreh; Haeri, Azadeh; Mahboubi, Arash; Mortazavi, Alireza; Dadashzadeh, Simin

    2016-04-01

    The purpose of this study was to prepare and characterize a hybrid system of moxifloxacin loaded niosomes incorporated into chitosan gel as a potential carrier for topical antimicrobial delivery. The prepared system was characterized regarding entrapment efficiency, particle size, zeta potential, in vitro drug release kinetics, morphology, FTIR analysis, bioadhesive strength and rheological behavior. The effect of different formulation parameters (surfactant type, surfactant to drug ratio, cholesterol percentage and loading methodology) on moxifloxacin entrapment and drug release was evaluated. The antibacterial effectiveness of various formulations was also assessed by measuring the minimal inhibitory concentrations, minimal bactericidal concentrations and agar diffusion assay using Pseudomonas aeruginosa and Staphylococcus aureus as model pathogens. The optimized niosomal formulation showed 73% drug entrapment, 47% drug release in 8h and was ∼290 nm in particle diameter and negatively charged (ζ∼-23 mV). The gel-embedded niosomes exhibited pseudo-plastic flow behavior and more sustained drug release profile compared to niosomes. The niosomal formulation of moxifloxacin was the most efficient system against P. aeruginosa, while gel based formulations were superior against S. aureus. Taken together, moxifloxacin-in-niosomes-in-gels hold great promise for topical microbial infections. Copyright © 2016 Elsevier B.V. All rights reserved.

  1. Lesion measurement in non-radioactive DNA by quantitative gel electrophoresis

    International Nuclear Information System (INIS)

    Sutherland, J.C.; Chen, Chun Zhang; Emrick, A.; Hacham, H; Monteleone, D.; Ribeiro, E.; Trunk, J.; Sutherland, B.M.

    1989-01-01

    The gel electrophoresis method developed during the past ten years in our laboratories makes possible the quantitation of UV induced pyrimidine dimers, gamma ray induced single- and double-strand breaks and many other types of lesions in nanogram quantities of DNA. The DNA does not have to be labeled with radionuclides or of a particular conformation, thus facilitating the use of the method in measuring damage levels and repair rates in the DNA of intact organisms -- including man. The gel method can quantitate any lesion in DNA that either is, or can be converted to a single- or double-strand break. The formation of a strand break produces two shorter DNA molecules for each molecule that existed before the treatment that produced the break. Determining the number of breaks, and hence the number of lesions, becomes a matter of comparing the average lengths of molecules in samples differing only in lesion-induced breaks. This requires that we determine the distribution of mass of DNA on a gel as a function of its distance of migration and also the dispersion function of its distance of migration and also the dispersion function (the relationship between molecular length and distance of migration) in the gel electrophoresis system. 40 refs., 5 figs

  2. Optimization and formulation design of carbopol loaded Piroxicam gel using novel penetration enhancers.

    Science.gov (United States)

    Chaudhary, Hema; Rohilla, Ajay; Rathee, Permender; Kumar, Vikash

    2013-04-01

    The aim of the study was to develop and optimize Piroxicam transdermal gel formulation using three-factor, three-level Box-Behnken design by deriving a second-order polynomial equation to construct contour plots for prediction of responses as three selected independent variables with ratio of carbopol 974 (X1), ratio of propylene glycol (PG) (X2) and ratio of ethanol (X3). The dependent variables studied were the skin permeation rate of piroxicam (Y1), viscosity of the gel (Y2) and pH of the gel (Y3). Response surface plots were drawn, statistical validity of the polynomials was established to find the compositions of optimized formulation which was evaluated using the vertical Franz-type diffusion cell. The permeation rate of piroxicam increased proportionally with ethanol concentration but decreased with polymer concentration. The design demonstrated the role of the derived polynomial equation and contour plots in predicting the values of dependent variables for the preparation and optimization of gel formulation. Copyright © 2013 Elsevier B.V. All rights reserved.

  3. Ocular ketoconazole-loaded proniosomal gels: formulation, ex vivo corneal permeation and in vivo studies.

    Science.gov (United States)

    Abdelbary, Ghada A; Amin, Maha M; Zakaria, Mohamed Y

    2017-11-01

    Vesicular drug carriers for ocular delivery have gained a real potential. Proniosomal gels as ocular drug carriers have been proven to be an effective way to improve bioavailability and patient compliance. Formulation and in vitro/ex vivo/in vivo characterization of ketoconazole (KET)-loaded proniosomal gels for the treatment of ocular keratitis. The effect of formulation variables; HLB value, type and concentration of non-ionic surfactants (Tweens, Spans, Brijs and Pluronics) with or without lecithin on the entrapment efficiency (EE%), vesicle size and in vitro KET release was evaluated. An ex vivo corneal permeation study to determine the level of KET in the external eye tissue of albino rabbits and an in vivo assessment of the level of KET in the aqueous humors were performed. In vivo evaluation showed an increase in bioavailability up to 20-folds from the optimum KET proniosomal gel formula in the aqueous humor compared to drug suspension (KET-SP). The selected formulae were composed of spans being hydrophobic suggesting the potential use of a more hydrophobic surfactant as Span during the formulation of formulae. Factors that stabilize the vesicle membrane and increase the entrapment efficiency of KET (namely low HLB, long alkyl chain, high phase transition temperature) slowed down the release profile. Proniosomal gels as drug delivery carriers were proven to be a promising approach to increase corneal contact and permeation as well as retention time in the eye resulting in a sustained action and enhanced bioavailability.

  4. Modeling the BZ reaction in gels with chemo-responsive crosslinks

    Science.gov (United States)

    Yashin, Victor V.; Kuksenok, Olga; Balazs, Anna C.

    2010-03-01

    We model chemo-responsive polymer gels, which expand and contract periodically in response to the ongoing oscillatory Belousov-Zhabotinsky (BZ) reaction. This behavior is due to a ruthenium catalyst, which is grafted to the polymers and affects the polymer-solvent interactions as it undergoes the redox oscillations in the course of the reaction. We consider a permanently crosslinked polymer gel that encompasses Ru(terpy)2 catalytic units having both the terpyridine ligands chemically bonded to the network. It is known that oxidation of the Ru metal-ion from Ru(II) to Ru(III) results in the dissociation of the Ru(terpy)2 complexes since the Ru(III) ions form only mono-complexes with terpyridine. Hence, the grafted Ru(terpy)2 units would effectively create crosslinks that break and re-form in the response to the BZ reaction. We modified the Oregonator model for the BZ reaction and took into account that the re-formation of Ru(terpy)2 complexes is frustrated by the gel network. The time-dependent elastic contribution of the Ru(terpy)2 crosslinks was described by the BKZ-type constitutive equation. We report on the results of simulations in 1D. We show, in particular, that compression of the sample leads to stiffening of the gel due to an increase in the crosslink density.

  5. PVC gel soft actuator-based wearable assist wear for hip joint support during walking

    Science.gov (United States)

    Li, Yi; Hashimoto, Minoru

    2017-12-01

    Plasticized polyvinyl chloride (PVC) gel and mesh electrode-based soft actuators have considerable potential to provide new types of artificial muscle, exhibiting similar responsiveness to biological muscle in air, >10% deformation, >90 kPa output stress, variable stiffness, long cycle life (>5 million cycles), and low power consumption. We have designed and fabricated a prototype of walking assist wear using the PVC gel actuator in previous study. The system has several advantages compared with traditional motor-based exoskeletons, including lower weight and power consumption, and no requirement for rigid external structures that constrain the wearer’s joints. In this study, we designed and established a control and power system to making the whole system portable and wearable outdoors. And we designed two control strategies based on the characteristics of the assist wear and the biological kinematics. In a preliminary experimental evaluation, a hemiparetic stroke patient performed a 10 m to-and-fro straight line walking task with and without assist wear on the affected side. We found that the assist wear enabled natural movement, increasing step length and decreasing muscular activity during straight line walking. We demonstrated that the assistance effect could be adjusted by controlling the on-off time of the PVC gel soft actuators. The results show the effectiveness of the proposed system and suggest the feasibility of PVC gel soft actuators for developing practical soft wearable assistive devices, informing the development of future wearable robots and the other soft actuator technologies for human movement assistance and rehabilitation.

  6. Silica scintillating materials prepared by sol-gel methods

    International Nuclear Information System (INIS)

    Werst, D.W.; Sauer, M.C. Jr.; Cromack, K.R.; Lin, Y.; Tartakovsky, E.A.; Trifunac, A.D.

    1993-01-01

    Silica was investigated as a rad-hard alternative to organic polymer hosts for organic scintillators. Silica sol-gels were prepared by hydrolysis of tetramethoxysilane in alcohol solutions. organic dyes were incorporated into the gels by dissolving in methanol at the sol stage of gel formation. The silica sol-gel matrix is very rad-hard. The radiation stability of silica scintillators prepared by this method is dye-limited. Transient radioluminescence was measured following excitation with 30 ps pulses of 20 MeV electrons

  7. Application of CMPO containing gels to metal extraction

    International Nuclear Information System (INIS)

    Dozol, J.F.; Brunette, J.P.

    1990-01-01

    Immersed in solubility-consistent organic solvents, high polymers can swell and form gels. Choosing the organic solvent among metal extracting solvents, metal extracting gels can be prepared. The advantages of the liquid-gel extraction process, in comparison with the liquid-liquid one, are to allow the extraction of metal cations from diluted aqueous solutions by using high aqueous-organic volume ratios (metal concentration in a few stages) with easy phase separations. Various CMPO (Octyl (phenyl) -N,N-diisobutylcarbamoylmethylphosphine oxide) containing gels have been prepared, and the extraction of europium (and related actinides) has been studied

  8. Aging and nonlinear rheology of thermoreversible colloidal gels

    Science.gov (United States)

    Wagner, Norman; Gordon, Melissa; Kloxin, Christopher

    Colloidal dispersions are found in a wide variety of consumer products such as paint, food and pharmaceuticals. We investigate gel formation and aging in a thermoreverible gel consisting of octadecyl-coated silica nanoparticles suspended in n-tetradecane. In this system, the octadecyl brush can undergo a phase change allowing the attractions between particles to be tuned by temperature (1,2). By probing the system with steady shear and large amplitude oscillatory shear, we have studied the effect of thermal history and shear history on gel formation and gel mechanical properties during aging. Gels were formed by approaching a common temperature from above and below to determine a reference state from which creep tests were conducted. Creep ringing was observed as expected for the viscoelastic gel. The rheological aging is interpreted in terms of the gel microstructure formed with differing thermal and shear histories to determine how processing affects structure. Recently proposed scaling laws for the rheology and structure under flow are explored within the context of gel aging (3). Through rheological and microstructural measurements, we will further the understanding of gel formation and aging in this model system which may be applied to processing conditions in an industrial setting.

  9. Photopatterned free-standing polyacrylamide gels for microfluidic protein electrophoresis.

    Science.gov (United States)

    Duncombe, Todd A; Herr, Amy E

    2013-06-07

    Designed for compatibility with slab-gel polyacrylamide gel electrophoresis (PAGE) reagents and instruments, we detail development of free-standing polyacrylamide gel (fsPAG) microstructures supporting electrophoretic performance rivalling that of microfluidic platforms. For the protein electrophoresis study described here, fsPAGE lanes are comprised of a sample reservoir and contiguous separation gel. No enclosed microfluidic channels are employed. The fsPAG devices (120 μm tall) are directly photopatterned atop of and covalently attached to planar polymer or glass surfaces. Leveraging the fast uses readily available materials and instruments - making this technique highly accessible.

  10. High Impulse Nanoparticulate-Based Gel Propellants, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposed Small Business Innovative Research (SBIR) Phase I addresses the development of advanced gel propellants and determination of their suitability for...

  11. PCR amplification on microarrays of gel immobilized oligonucleotides

    Science.gov (United States)

    Strizhkov, Boris; Tillib, Sergei; Mikhailovich, Vladimir; Mirzabekov, Andrei

    2003-11-04

    The invention relates two general methods for performing PCR amplification, combined with the detection and analysis of the PCR products on a microchip. In the first method, the amplification occurs both outside and within a plurality of gel pads on a microchip, with at least one oligonucleotide primer immobilized in a gel pad. In the second method, PCR amplification also takes place within gel pads on a microchip, but the pads are surrounded by a hydrophobic liquid such as that which separates the individual gel pads into environments which resemble micro-miniaturized test tubes.

  12. Disc electrophoresis and related techniques of polyacrylamide gel electrophoresis

    National Research Council Canada - National Science Library

    Maurer, H. R

    1971-01-01

    ..., enzymes, antingens and radioactively labelled materials, and detailed treatments of micro disc electrophoresis, preparative polyacrylamide gel electrophoresis and many other techniques for special problems...

  13. Design of the mechanical properties of the gel by the 3D gel printer "SWIM-ER"

    Science.gov (United States)

    Saito, Azusa; Ota, Takafumi; Tase, Taishi; Takamatsu, Kyuichiro; Kawakami, Masaru; Furukawa, Hidemitsu

    2017-04-01

    In this study, we evaluated the mechanical properties of printed structures with respect to the printing orientation for "SWIM-ER". The fracture surface of the 3D modeled object of the gel does not break along the stacked line, and the maximum stress at that time is the breaking strength. Moreover, the dependency in the stacking direction is weak in the 3D model of the gel. The gel printed at high speed scan showed lower elastic modulus and higher moisture content than gel printed at low speed scan. We discussed about crosslinking density calculated based on the compressive elastic modulus and moisture content, respectively. It was found that gels having different crosslinking density can be formed by the scanning speed of UV laser. In addition, we made a prototype of a gel finger model with different mechanical properties within the model.

  14. Influence of ionic constituents and electrical conductivity on the propagation of charged nanoscale objects in passivated gel electrophoresis.

    Science.gov (United States)

    Bikos, Dimitri A; Mason, Thomas G

    2018-01-01

    When determining the electric field E acting on charged objects in gel electrophoresis, the electrical conductivity of the buffer solution is often overlooked; E is typically calculated by dividing the applied voltage by a separation distance between electrodes. However, as a consequence of electrolytic reactions, which occur at the electrodes, gradients in the ionic content of the buffer solution and its conductivity can potentially develop over time, thereby impacting E and affecting propagation velocities of charged objects, v, directly. Here, we explore how the types and concentrations of ionic constituents of the buffer solution, which largely control its conductivity, when used in passivated gel electrophoresis (P-gelEP), can influence E, thereby altering v of charged nanospheres propagating through large-pore gels. We measure the conductivity of the buffer solution in the center of the gel region near propagating bands of nanospheres, and we show that predictions of E based on conductivity closely correlate with v. We also explore P-gelEP involving two different types of passivation agents: nonionic polyethylene glycol (PEG) and anionic sodium dodecyl sulfate (SDS). Our observations indicate that using a conductivity model to determine E from the local current density and the conductivity where spheres are propagating can lead to a better estimate than the standard approach of a voltage divided by a separation. Moreover, this conductivity model also provides a starting point for interpreting the complex behavior created by amphiphilic ionic passivation agents, such as SDS, on propagating nanospheres used in some P-gelEP experiments. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Core-Shell Microneedle Gel for Self-Regulated Insulin Delivery.

    Science.gov (United States)

    Wang, Jinqiang; Ye, Yanqi; Yu, Jicheng; Kahkoska, Anna R; Zhang, Xudong; Wang, Chao; Sun, Wujin; Corder, Ria D; Chen, Zhaowei; Khan, Saad A; Buse, John B; Gu, Zhen

    2018-03-27

    A bioinspired glucose-responsive insulin delivery system for self-regulation of blood glucose levels is desirable for improving health and quality of life outcomes for patients with type 1 and advanced type 2 diabetes. Here we describe a painless core-shell microneedle array patch consisting of degradable cross-linked gel for smart insulin delivery with rapid responsiveness and excellent biocompatibility. This gel-based device can partially dissociate and subsequently release insulin when triggered by hydrogen peroxide (H 2 O 2 ) generated during the oxidation of glucose by a glucose-specific enzyme covalently attached inside the gel. Importantly, the H 2 O 2 -responsive microneedles are coated with a thin-layer embedding H 2 O 2 -scavenging enzyme, thus mimicking the complementary function of enzymes in peroxisomes to protect normal tissues from injury caused by oxidative stress. Utilizing a chemically induced type 1 diabetic mouse model, we demonstrated that this smart insulin patch with a bioresponsive core and protective shell could effectively regulate the blood glucose levels within a normal range with improved biocompatibility.

  16. Influence of Uranium and Polivinyl Alcohol Concentration in the Feed of Sol Gel Process on the Gel Spherical Product

    International Nuclear Information System (INIS)

    Indra Suryawan; Endang Susiantini

    2007-01-01

    The gel particles have been made at various uranium and polyvinyl alcohol concentration in the sol gel process. The variables of uranium concentration were 0.3; 0.5; 0.7; 0.9; 1.1; 1.3; 1.5; 1.7; 1.9 and 2.1 M The variables of polyvinyl alcohol concentration were 0.3; 0.6; 0.9; 1.2; 1.5; 1.8; 2.1 and 2.4 M After drying the sol gel process products were heated at 300, 500 and 750°C during 4 hours. The gel particles were characterized using an optic microscope to know the shape and condition morphology of gel. From experimental result using uranium concentration of 0.3 until 2.1 M and polyvinyl alcohol of 1.8 until 2.4 M spherical and gel was formed elastic, after heating at 750°C it was unbreakable. At the concentration of polyvinyl alcohol from 0.3 to 0.5 M, the gel product was soft and broken after being dried. At the concentration of polyvinyl alcohol from 0.6 to 0.8 M, the dried gel product was not perfect. At the concentration of polyvinyl alcohol from 0.9 to 1.7 M, the gel product of gelation process was spherical and it was broken after being heated up to 300°C. (author)

  17. Gel-eletroforese no diagnóstico da varíola Gel-electrophoresis in the smallpox diagnosis

    Directory of Open Access Journals (Sweden)

    Julio A. Mesquita

    1972-01-01

    Full Text Available O emprego de gel-eletroforese no diagnóstico da varíola, demonstrou ser ao menos trinta vezes (30X mais sensível que o teste de agar-gel, nas condições descritas (tabela I. Doze (12 espécimes, cujos testes convencionais de inoculação em ovos embrionados e de agar-gel resultaram positivos, foram testados em suas diluições originais congeladas por mais de um ano, sendo seis deles revelados por gel-eletroforese enquanto nenhum o foi por agar-gel (tabela II. Trinta e três (33 amostras isoladas no laboratório, foram testadas com material colhido de membrana cório-alantóica da primeira inoculação para o diagnóstico, conservado em glicerina 50%, resultando 15 positivas em gel-eletroforese e apenas 3 em agar-gel (tabela II. Os últimos 60 espécimes recebidos para diagnóstico, através a Campanha de Erradicação da Varíola, também resultaram negativos em gel-eletroforese, que não mostrou falsos-positivos nas condições descritas.The test of gel-electrophoresis applied to the pox virus group showed to be at least thirth times (30X more sensitive than agar-gel test on the described conditions (Table I. Twelve specimens, which were positives form Smallpox in the conventional tests of egg inoculation and agar-gel difusion test, have been screened in their original dilutions frozen for more than 1 year and six of them were still detectable by gel-eletrophoresis, while by agar-gel test any of them was positive (Table II. Thirty three Smallpox isolates have been tested with material from first egg inoculation (chorioallantoic membranes which have been stored in glycerin 50%, at - 15ºC. Fifteen of them were still positive by gel-electrophoresis and only 3 by agar-gel (Table II. The last 60 specimens received for diagnosis from Smallpox Erradication Campaign (CEV, were negatives by both tests. The gel-electrophoresis, did not show false-positives on described conditions.

  18. Environmentally benign sol-gel antifouling and foul-releasing coatings.

    Science.gov (United States)

    Detty, Michael R; Ciriminna, Rosaria; Bright, Frank V; Pagliaro, Mario

    2014-02-18

    Biofouling on ships and boats, characterized by aquatic bacteria and small organisms attaching to the hull, is an important global issue, since over 80000 tons of antifouling paint is used annually. This biofilm, which can form in as little as 48 hours depending on water temperature, increases drag on watercraft, which greatly reduces their fuel efficiency. In addition, biofouling can lead to microbially induced corrosion (MIC) due to H2S formed by the bacteria, especially sulfate-reducing bacteria. When the International Maritime Organization (IMO) international convention banned the use of effective but environmentally damaging coatings containing tributyl tin in 2008, the development of clean and effective antifouling systems became more important than ever. New nonbiocidal coatings are now in high demand. Scientists have developed new polymers, materials, and biocides, including new elastomeric coatings that they have obtained by improving the original silicone (polydimethylsiloxane) formulation patented in 1975. However, the high cost of silicones, especially of fluoropolymer-modified silicones, has generally prevented their large-scale diffusion. In 2009, traditional antifouling coatings using cuprous oxide formulated in copolymer paints still represented 95% of the global market volume of anti-fouling paints. The sol-gel nanochemistry approach to functional materials has emerged as an attractive candidate for creating low fouling surfaces due to the unique structure and properties of silica-based coatings and of hybrid inorganic-organic silicas in particular. Sol-gel formulations easily bind to all types of surfaces, such as steel, fiberglass, aluminum, and wood. In addition, they can cure at room temperature and form thin glassy coatings that are markedly different from thick silicone elastomeric foul-releasing coatings. Good to excellent performance against biofouling, low cure temperatures, enhanced and prolonged chemical and physical stability, ease of

  19. Radiological properties of MAGIC normoxic polymer gel dosimetry

    Science.gov (United States)

    Aljamal, M.; Zakaria, A.; Shamsuddin, S.

    2013-04-01

    For a polymer gel dosimeter to be of use in radiation dosimetry, it should display water-equivalent radiological properties. In this study, the radiological properties of the MAGIC (Methacrylic and Ascorbic acid in Gelatin Initiated by Copper) normoxic polymer gels were investigated. The mass density (ρ) was determined based on Archimedes' principle. The weight fraction of elemental composition and the effective atomic number (Zeff) were calculated. The electron density was also measured with 90° scattering angle at room temperature. The linear attenuation coefficient (μ) of unirradiated gel, irradiated gel, and water were determined using Am-241 based on narrow beam geometry. Monte Carlo simulation was used to calculate the depth doses response of MAGIC gel and water for 6MV photon beam. The weight fractions of elements composition of MAGIC gel were close to that for water. The mass density was found to be 1027 ± 2 kg m-3, which is also very close to mass density of muscle tissue (1030 kg m-3) and 2.7% higher than that of water. The electron density (ρe) and atomic number (Zeff) were found to be 3.43 × 1029 e m-3 and 7.105, respectively. The electron density measured was 2.6% greater than that for water. The atomic number was very close to that for water. The prepared MAGIC gel was found to be water equivalent based on the study of element composition, mass density, electron density and atomic number. The linear attenuation coefficient of unirradiated gel was very close to that of water. The μ of irradiated gel was found to be linear with dose 2-40 Gy. The depth dose response for MAGIC gel from a 6 MV photon beam had a percentage dose difference to water of less than 1%. Therefore it satisfies the criteria to be a good polymer gel dosimeter for radiotherapy.

  20. Sorption of neptunium(V) on silicate gels

    International Nuclear Information System (INIS)

    Del Nero, M.; Bontems, G.; Advocat, T.; Jollivet, P.

    1999-01-01

    Aqueous corrosion of nuclear waste glasses induces the formation of a gel layer enriched in hydrolyzable elements. To assess the role of such layers on the migration of Np(V) from repositories to environment, and determine the retention mechanisms, experiments have been undertaken on synthetic pure silica and on ferrisilicate gels as model solids. No detailed and systematic studies on silicate gels as scavengers for Np(V) appear to have been devoted to the influence of solution parameters and gel composition on the sorption of Np(V) on silicate gels. In this work, the fractional uptake of Np(V) on a synthetic pure silica gel and on synthetic ferrisilicate gels of controlled Si/Fe proportions (3 and 10) was measured at different ionic strengths (0.5 to 0.01 M) and Np(V) concentration levels ≅10 -10 M and 10 -6 M with pH as the main variable (3 to 10). The pH dependence of Np(V) sorption on the alternation gel was also investigated for different initial concentrations of Np(V) in the aqueous phase ≅10 -10 M, 10 -6 M and 10 -5 M. Batch experiments were carried out at 298 K under CO 2 -free conditions to avoid the formation of Np(V) carbonate complexes in the solution. As a part of this work, the charge characteristics of the gel surfaces were determined either by studying the retention of the electrolyte ions as counterions to the surface charges, as a function of pH and ionic strength of the solution contacted with gels, or by performing acid/base titrations of the alteration gel suspensions. (J.P.N.)

  1. Novel inorganic tin phosphate gel: multifunctional material.

    Science.gov (United States)

    Huang, Wenyan; Komarneni, Sridhar; Noh, Young Dong; Ma, Jianfeng; Chen, Kunfeng; Xue, Dongfeng; Xue, Xiaoqiang; Jiang, Bibiao

    2018-03-08

    Here, we report a remarkable 15 Å nanolayered tin phosphate, Sn(HPO 4 ) 2 ·3H 2 O (SnP-H + or SnP), and its clay-like gel, which are multifunctional and are prepared using earth-abundant Sn and P chemicals by a facile, environmentally benign and potentially cost-effective process. This new energy material is discovered here as the best proton conductor among all the known layered phosphates with a very high proton conductivity of over 1 × 10 -2 S cm -1 at 100 °C for potential use in PEM fuel cells. But it is also a very good capacitor material with fast Li-storage kinetics (charging time of 13 s).

  2. Phyllosilicates and Amorphous Gel in the Nakhlites

    Science.gov (United States)

    Hicks, L. J.; Bridges, J. C.; Gurman, S. J.

    2013-09-01

    Previous studies of the nakhlite martian meteorites have revealed hydrothermal minerals present within the fractures of the olivine minerals and the mesostasis. The olivine fractures of the Lafayette nakhlite reveal variations with initial deposits of siderite on the fracture walls, followed by crystalline phyllosilicates (smectite), and finishing with a rapidly cooled amorphous silicate gel within the central regions of the fractures. The mesostasis fractures of Lafayette also contain a crystalline phyllosilicate (serpentine). The amorphous gel is the most abundant secondary phase within the fractures of the other nakhlites [1, 2]. By studying nine nakhlite samples, including Lafayette, Governador Valadares, Nakhla, Y-000593, Y-000749, Miller-Range 03346, NWA 817, NWA 998, and NWA 5790, our aim is to constrain the identity of the phyllosilicate secondary phase minerals found throughout the nakhlite martian meteorites. This is achieved using methods including Electron Probe Micro-analysis (EPMA); X-ray Absorption Near-Edge Structure (Fe-K XANES) spectroscopy measured using Beamline I-18 at the Diamond Light Source synchrotron; and the use of Transmission Electron Microscopy (TEM) at the University of Leicester for High-Resolution (HR) imaging and Selected Area Electron Diffraction (SAED). BF studying nine nakhlite samples, including Lafayette, Governador Valadares, Nakhla, Y-000593, Y-000749, Miller-Range 03346, NWA 817, NWA 998, and NWA 5790, our aim is to constrain the identity of the phyllosilicate secondary phase minerals found throughout the nakhlite martian meteorites. This is achieved using methods including Electron Probe Micro-analysis (EPMA); X-ray Absorption Near-Edge Structure (Fe-K XANES) spectroscopy measured using Beamline I-18 at the Diamond Light Source synchrotron; and the use of Transmission Electron Microscopy (TEM) at the University of Leicester for High-Resolution (HR) imaging and Selected Area Electron Diffraction (SAED).

  3. Clotrimazole nanoparticle gel for mucosal administration

    Energy Technology Data Exchange (ETDEWEB)

    Esposito, Elisabetta, E-mail: ese@unife.it [Department of Pharmaceutical Sciences, University of Ferrara, I-44121 Ferrara (Italy); Ravani, Laura [Department of Pharmaceutical Sciences, University of Ferrara, I-44121 Ferrara (Italy); Contado, Catia [Department of Chemistry, University of Ferrara, Ferrara (Italy); Costenaro, Andrea [Department of Pharmaceutical Sciences, University of Ferrara, I-44121 Ferrara (Italy); Drechsler, Markus [Macromolecular Chemistry II, University of Bayreuth (Germany); Rossi, Damiano [Department of Biology and Evolution, LT Terra and Acqua Tech UR7, University of Ferrara, Ferrara (Italy); Menegatti, Enea [Department of Pharmaceutical Sciences, University of Ferrara, I-44121 Ferrara (Italy); Grandini, Alessandro [Department of Biology and Evolution, LT Terra and Acqua Tech UR7, University of Ferrara, Ferrara (Italy); Cortesi, Rita [Department of Pharmaceutical Sciences, University of Ferrara, I-44121 Ferrara (Italy)

    2013-01-01

    In this study a formulation suitable to be applied on oral and/or vaginal mucosa has been developed for the treatment of fungal infections. The aim of the research is a comparison between clotrimazole (CLO) containing semisolid formulations based on monoolein aqueous dispersion (MAD) or nanostructured lipid carrier (NLC). MAD and NLC have been characterized in terms of morphology and dimensional distribution by cryogenic Transmission Electron Microscopy (cryo-TEM) and Photon Correlation Spectroscopy (PCS). CLO was encapsulated with high entrapment efficiency both in MAD and in NLC, according to Sedimentation Field Flow Fractionation (SdFFF) combined with HPLC. CLO recovery in MAD and NLC has been investigated by time. In order to obtain formulations with suitable viscosity for mucosal application, MAD was diluted with a carbomer gel, while NLC was directly viscosized by the addition of poloxamer 407 in the dispersion. The rheological properties of MAD and NLC after viscosizing have been investigated. Franz cell has been employed to study CLO diffusion from the different vehicles, evidencing diffusion rates from MAD and NLC superimposable to that obtained using Canesten{sup Registered-Sign }. An anticandidal activity study demonstrated that both CLO-MAD and CLO-NLC were more active against Candida albicans with respect to the pure drug. Highlights: Black-Right-Pointing-Pointer Comparison between monoolein aqueous dispersion (MAD) and nanostructured lipid carrier (NLC). Black-Right-Pointing-Pointer Clotrimazole (CLO) encapsulated with high entrapment efficiency both in MAD and in NLC. Black-Right-Pointing-Pointer The solid matrix of NLC controls CLO degradation better than MAD. Black-Right-Pointing-Pointer CLO containing MAD and NLC exhibits a higher anticandidal activity than the free drug. Black-Right-Pointing-Pointer Simple production of CLO-NLC based poloxamer gel, suitable for industry scaling up.

  4. Automatic analysis of 2D polyacrylamide gels in the diagnosis of DNA polymorphisms

    Science.gov (United States)

    2013-01-01

    Introduction The analysis of polyacrylamide gels is currently carried out manually or automatically. In the automatic method, there are limitations related to the acceptable degree of distortion of lane and band continuity. The available software cannot deal satisfactorily with this type of situations. Therefore, the paper presents an original image analysis method devoid of the aforementioned drawbacks. Material This paper examines polyacrylamide gel images from Li-Cor DNA Sequencer 4300S resulting from the use of the electrophoretic separation of DNA fragments. The acquired images have a resolution dependent on the length of the analysed DNA fragments and typically it is MG×NG=3806×1027 pixels. The images are saved in TIFF format with a grayscale resolution of 16 bits/pixel. The presented image analysis method was performed on gel images resulting from the analysis of DNA methylome profiling in plants exposed to drought stress, carried out with the MSAP (Methylation Sensitive Amplification Polymorphism) technique. Results The results of DNA polymorphism analysis were obtained in less than one second for the Intel Core™ 2 Quad CPU Q9300@2.5GHz, 8GB RAM. In comparison with other known methods, specificity was 0.95, sensitivity = 0.94 and AUC (Area Under Curve) = 0.98. Conclusions It is possible to carry out this method of DNA polymorphism analysis on distorted images of polyacrylamide gels. The method is fully automatic and does not require any operator intervention. Compared with other methods, it produces the best results and the resulting image is easy to interpret. The presented method of measurement is used in the practical analysis of polyacrylamide gels in the Department of Genetics at the University of Silesia in Katowice, Poland. PMID:23835039

  5. Modelling of erosion of bentonite gel by gel/sol flow

    Energy Technology Data Exchange (ETDEWEB)

    Moreno, Luis; Neretnieks, Ivars; Longcheng Liu (Chemical Engineering and Technology, School of Chemical Science and Engineering, Royal Institute of Technology, Stockholm (Sweden))

    2010-11-15

    Bentonite intrusion into a fracture intersecting the canister deposition hole is modelled. The model describes the expansion of the bentonite within the fracture. It accounts for the repulsive electrostatic double-layer forces, the attractive van der Waals forces and friction forces between the particles and the water. The model also takes into account the diffusion of the colloid particles in the smectite sol. Diffusion of a counterion, sodium, is accounted for as this strongly influences the double layer force and the viscosity of the gel/sol. The gel/sol is considered to be a fluid with a varying viscosity that is strongly dependent on the bentonite volume fraction in the gel and the sodium concentration in the water. Two different geometries were modelled; a rectangular and a cylindrical. The rectangular geometry was used to gain experience with the processes and mechanisms and how they interact since the cylindrical geometry was somewhat less stable numerically and more time consuming. In the rectangular geometry a fracture 1 metre long in the flow direction was modelled. In both geometries the fracture size was selected sufficiently large to ensure that the water velocity, near the distant border was nearly the same as the approaching water velocity and that the smectite concentration there was vanishingly small. It was found that the velocity of the fluid drops considerably where the bentonite volume fraction is larger than 1-2%. This is due to the strong increase in viscosity with increasing bentonite volume fraction. The loss of smectite by the slowly flowing fluid was found to be proportional to the square root of the seeping water velocity for the rectangular geometry. For the cylindrical geometry, the dependence is somewhat lower (exponent about 0.4) since the length of the gel/water interface decreases with increasing water flow rate. The penetration depth of the gel/water interface decreases with increasing water flow rate. For water velocity of the

  6. Explorative data analysis of two-dimensional electrophoresis gels

    DEFF Research Database (Denmark)

    Schultz, J.; Gottlieb, D.M.; Petersen, Marianne Kjerstine

    2004-01-01

    Methods for classification of two-dimensional (2-DE) electrophoresis gels based on multivariate data analysis are demonstrated. Two-dimensional gels of ten wheat varieties are analyzed and it is demonstrated how to classify the wheat varieties in two qualities and a method for initial screening...

  7. Highly Elastic and Self-Healing Composite Colloidal Gels.

    NARCIS (Netherlands)

    Diba, M.; Wang, H.; Kodger, T.E.; Parsa, S.; Leeuwenburgh, S.C.G.

    2017-01-01

    Composite colloidal gels are formed by the pH-induced electrostatic assembly of silica and gelatin nanoparticles. These injectable and moldable colloidal gels are able to withstand substantial compressive and tensile loads, and exhibit a remarkable self-healing efficiency. This study provides new,

  8. Comparative antimicrobial activities of aloe vera gel and leaf ...

    African Journals Online (AJOL)

    The comparative antimicrobial activities of the gel and leaf of Aloe vera were tested against Staphylococcus aureus, Pseudomonas aeruginosa, Trichophyton mentagraphytes, T. schoeleinii, Microsporium canis and Candida albicans. Ethanol was used for the extraction of the leaf after obtaining the gel from it. Antimicrobial ...

  9. Fast Dissolving Tablets of Aloe Vera Gel | Madan | Tropical Journal ...

    African Journals Online (AJOL)

    Purpose: The objective of this work was to prepare and evaluate fast dissolving tablets of the nutraceutical, freeze dried Aloe vera gel. Methods: Fast dissolving tablets of the nutraceutical, freeze-dried Aloe vera gel, were prepared by dry granulation method. The tablets were evaluated for crushing strength, disintegration ...

  10. Growth, characterization and dielectric property studies of gel grown ...

    Indian Academy of Sciences (India)

    Administrator

    Dielectric constant and dielectric loss have been calculated and discussed as a function of frequency at different temperatures. ... The stock solu- tion is added until the pH of the gel is set at the desired value. Test tubes were then tightly closed to prevent evaporation and contamination of the exposed surface of the gel by ...

  11. Biocatalysis with Sol-Gel Encapsulated Acid Phosphatase

    Science.gov (United States)

    Kulkarni, Suhasini; Tran, Vu; Ho, Maggie K.-M.; Phan, Chieu; Chin, Elizabeth; Wemmer, Zeke; Sommerhalter, Monika

    2010-01-01

    This experiment was performed in an upper-level undergraduate biochemistry laboratory course. Students learned how to immobilize an enzyme in a sol-gel matrix and how to perform and evaluate enzyme-activity measurements. The enzyme acid phosphatase (APase) from wheat germ was encapsulated in sol-gel beads that were prepared from the precursor…

  12. 3D Architectured Polyazomethine Gel Synthesis: Its Self Assembled ...

    Indian Academy of Sciences (India)

    23

    synthesis of polyazomethine polymer gel materials. The synthesized polymer gel is characterized by different physical techniques for testing its proper existence such as FESEM analysis, TGA analysis, DSC analysis, FTIR analysis and EDXS analysis. The morphological study has revealed that the material is having 3D ...

  13. Development and evaluation of ibuprofen transdermal gel formulations

    African Journals Online (AJOL)

    A commercial ibuprofen gel product (Ibutop®) was used as a reference. Results: The formulations containing 5 % of either menthol or glycerol as permeation enhancers gave drug release patterns comparable to that of the reference product. Propanol increased the apparent viscosity of the test gels to the same extent as that ...

  14. Radiation reaction of skin treatment with nucliderm-gel

    International Nuclear Information System (INIS)

    Pandova, V.; Marinova, Ts.; Stefanova, D.; Pantev, T.; Yankova, S.

    1988-01-01

    The process of epithelization and the anticeptic effect of nucliderm-gel applied locally have been studied in 63 oncological patients subjected to radiotherapy. In all cases under study nucliderm-gel promotes skin epithelization and has a high antiseptic effect as compared with the drugs applied hitherto

  15. Method of making ionic liquid mediated sol-gel sorbents

    Science.gov (United States)

    Malik, Abdul; Shearrow, Anne M.

    2017-01-31

    Ionic liquid (IL)-mediated sol-gel hybrid organic-inorganic materials present enormous potential for effective use in analytical microextraction. One obstacle to materializing this prospect arises from high viscosity of ILs significantly slowing down sol-gel reactions. A method was developed which provides phosphonium-based, pyridinium-based, and imidazolium-based IL-mediated advanced sol-gel organic-inorganic hybrid materials for capillary microextraction. Scanning electron microscopy results demonstrate that ILs can serve as porogenic agents in sol-gel reactions. IL-mediated sol-gel coatings prepared with silanol-terminated polymers provided up to 28 times higher extractions compared to analogous sol-gel coatings prepared without any IL in the sol solution. This study shows that IL-generated porous morphology alone is not enough to provide effective extraction media: careful choice of the organic polymer and the precursor with close sol-gel reactivity must be made to ensure effective chemical bonding of the organic polymer to the created sol-gel material to be able to provide the desired sorbent characteristics.

  16. Preparation of an efficient humidity indicating silica gel from rice ...

    Indian Academy of Sciences (India)

    Administrator

    Abstract. An efficient humidity indicating silica gel was prepared using rice husk ash as a raw material via sodium silicate extraction and acid neutralization method. Cobalt chloride was impregnated into the silica gel as a colour indicating material. A low concentration of cobalt chloride solution (0⋅0005 mol dm–3) was used ...

  17. Viscoelastic nature of Au nanoparticle–PDMS nanocomposite gels

    Indian Academy of Sciences (India)

    A stable gel of Au nanoparticles in polydimethylsiloxane (PDMS) nanocomposite is prepared by employing the curing agent of PDMS elastomer as a reducing agent for the formation of Au nanoparticles by an in-situ process. The viscoelastic nature of these gels is very sensitive to the Au nanoparticle loading and the ...

  18. Starch gel electrophoresis of conifer seeds: a laboratory manual

    Science.gov (United States)

    M. Thompson Conkle; Paul D. Hodgskiss; Lucy B. Nunnally; Serena C. Hunter

    1982-01-01

    This manual describes fast, low-cost biochemical procedures for separating enzymes representing numerous genes of forest trees. During electrophoresis the mixture of enzymes from a megagametophyte or embryo of a germinated seed separates in a gel. Specific stains applied to gel slices locate each enzyme. These procedures expand on those developed for crops research....

  19. Self-Healing Corrosion Protective Sol-Gel Coatings

    NARCIS (Netherlands)

    Abdolah Zadeh, M.

    2016-01-01

    Inspired by the state of the art and the recent advances in the field of self-healing corrosion protective coatings, the thesis entitled “Self-healing corrosion protective sol-gel coatings” addresses novel routes to self-healing corrosion protective sol-gel coatings via extrinsic and intrinsic

  20. Recovery of DNA from agarose gel by trap method

    African Journals Online (AJOL)

    Administrator

    2011-09-05

    Sep 5, 2011 ... target band and refilling it with the same buffer. When the molecules of DNA move from agarose gel into a well, the velocity of DNA will increase in the well without interaction between gel and DNA (Stellwagen and. Stellwagen, 2009). It is possible to recover them from the. *Corresponding author. E-mail: ...

  1. Rheological properties of soybean protein isolate gels containing emulsion droplets

    NARCIS (Netherlands)

    Kim, K.H.; Renkema, J.M.S.; Vliet, van T.

    2001-01-01

    Rheological properties of soybean protein gels containing various volume fractions oil droplets have been studied at small and large deformations. Dynamic viscoelastic properties of soybean protein isolate gels were determined as a function of the volume fraction of oil droplets stabilised by the

  2. Inexpensive and Safe DNA Gel Electrophoresis Using Household Materials

    Science.gov (United States)

    Ens, S.; Olson, A. B.; Dudley, C.; Ross, N. D., III; Siddiqi, A. A.; Umoh, K. M.; Schneegurt, M. A.

    2012-01-01

    Gel electrophoresis is the single most important molecular biology technique and it is central to life sciences research, but it is often too expensive for the secondary science classroom or homeschoolers. A simple safe low-cost procedure is described here that uses household materials to construct and run DNA gel electrophoresis. Plastic…

  3. Electrical conductivity measurements on gel grown KDP crystals ...

    Indian Academy of Sciences (India)

    Unknown

    †Scott Christian College, Nagercoil 629 003, India. MS received 4 September 2000; revised 16 July 2001. Abstract. Pure and impurity added (with urea and thiourea) KDP single crystals were grown by the gel method using silica gels. Electrical conductivity measurements were carried out along both the unique axis and.

  4. 3D Architectured polyazomethine gel synthesis: its self-assembled ...

    Indian Academy of Sciences (India)

    2018-03-28

    Mar 28, 2018 ... Abstract. Azomethine is the key linkage in all Schiff base reactions. The present context has efficiently emphasized on the utilization of Schiff base strategy effectively in the synthesis of polyazomethine polymer gel materials. The synthesized polymer gel is characterized by different physical techniques for ...

  5. Electrical conductivity measurements on gel grown KDP crystals ...

    Indian Academy of Sciences (India)

    2CO3 and (NH4)2SO4] KDP sin- gle crystals were grown by the gel method using silica gels. Electrical conductivity measurements were carried out along both the unique axis and perpendicular directions at various temperatures ranging from 28 ...

  6. Electrical conductivity measurements on gel grown KDP crystals ...

    Indian Academy of Sciences (India)

    Pure and impurity added (with urea and thiourea) KDP single crystals were grown by the gel method using silica gels. Electrical conductivity measurements were carried out along both the unique axis and perpendicular directions at various temperatures ranging from 30 to 140°C by the conventional two-probe method.

  7. Evaluation of Topical Gel Bases Formulated with Various Essential ...

    African Journals Online (AJOL)

    Evaluation of Topical Gel Bases Formulated with Various Essential Oils for Antibacterial Activity against Methicillin- Resistant Staphylococcus Aureus. ... Lemon grass and thyme oils were chosen for further studies, including analysis of their composition by gas chromatography–mass spectrometry (GC/MS). Gels were ...

  8. Activation energy for mullitization of gel fibres obtained from ...

    Indian Academy of Sciences (India)

    and aluminum nitrate was optimized to obtain spinnable precursor sol for synthesis of fibres. Thermogravimetry– ... (XRD) analyses were used to characterize properties of the gel and ceramic fibres. The precursor gel completely .... The polymer chains of M–O–M and M–OH–M were present while the condensation ...

  9. Comparison of the effectiveness of polymer gel dosimeters (Magic ...

    African Journals Online (AJOL)

    Purpose: To investigate and compare two polymer gel dosimeters, Magic and Pagatug, as organ dosimeters for 3D measurement of dose distribution in brachytherapy, nuclear medicine and teletherapy. Methods: Magic and Pagatug polymer gels were compared with soft tissue based on irradiation with low energy photons ...

  10. DSC and conductivity studies on PVA based proton conducting gel ...

    Indian Academy of Sciences (India)

    Unknown

    An attempt has been made in the present work to prepare polyvinyl alcohol (PVA) based proton conducting gel electrolytes in ammonium thiocyanate (NH4SCN) solution and characterize ... dependence of ionic conductivity exhibits VTF behaviour. Keywords. Polymer gel electrolytes; ionic conductivity; solvent free polymer ...

  11. Evaluation of wheat by polyacrylamide gel electrophoresis | Shuaib ...

    African Journals Online (AJOL)

    ... polyacrylamide gel electrophoresis (SDS-PAGE). Electrophorogram for each variety were scored and presence or absence of each band noted and was entered in a binary data matrix. Based on the data of SDS-PAGE gels cluster analysis was performed to check the variations among varieties. The overall result shows ...

  12. Gadolinium-loaded gel scintillators for neutron and antineutrino detection

    Energy Technology Data Exchange (ETDEWEB)

    Riddle, Catherine Lynn; Akers, Douglas William; Demmer, Ricky Lynn; Paviet, Patricia Denise; Drigert, Mark William

    2016-11-29

    A gadolinium (Gd) loaded scintillation gel (Gd-ScintGel) compound allows for neutron and gamma-ray detection. The unique gel scintillator encompasses some of the best features of both liquid and solid scintillators, yet without many of the disadvantages associated therewith. Preferably, the gel scintillator is a water soluble Gd-DTPA compound and water soluble fluorophores such as: CdSe/ZnS (or ZnS) quantum dot (Q-dot) nanoparticles, coumarin derivatives 7-hydroxy-4-methylcoumarin, 7-hydroxy-4-methylcoumarin-3-acetic acid, 7-hydroxycoumarin-3-carboxylic acid, and Alexa Fluor 350 as well as a carbostyril compound, carbostyril 124 in a stable water-based gel, such as methylcellulose or polyacrylamide polymers. The Gd-loaded ScintGel allows for a homogenious distribution of the Gd-DTPA and the fluorophores, and yields clean fluorescent emission peaks. A moderator, such as deuterium or a water-based clear polymer, can be incorporated in the Gd-ScintGel. The gel scintillators can be used in compact detectors, including neutron and antineutrino detectors.

  13. Development and mechanical characterisation of self-compressed collagen gels.

    Science.gov (United States)

    Andriakopoulou, C E; Zadpoor, A A; Grant, M H; Riches, P E

    2018-03-01

    Collagen gels are considered a promising biomaterial for the manufacturing of tissue engineering scaffolds, however, their mechanical properties often need to be improved to enable them to provide enough mechanical support during the course of tissue regeneration process. In this paper, we present a simple self-compression technique for the improvement of the mechanical properties of collagen gels, identified by the fitting of bespoke biphasic finite element models. Radially-confined highly hydrated gels were allowed to self-compress for 18h, expelling fluid, and which were subsequently subjected to unconfined ramp-hold compression. Gels, initially of 0.2%, 0.3% and 0.4% (w/v) collagen and 13mm thickness, transformed to 2.9±0.2%, 3.2±0.3% and 3.6±0.1% (w/w) collagen and 0.45±0.06mm, 0.69±0.04mm and 0.99±0.07mm thickness. Young's moduli of the compressed gels did not increase with increasing collagen fibril density, whilst zero-strain hydraulic permeability significantly decreased from 51 to 21mm 4 /Ns. The work demonstrates that biphasic theory, applied to unconfined compression, is a highly appropriate paradigm to mechanically characterise concentrated collagen gels and that confined compression of highly hydrated gels should be further investigated to enhance gel mechanical performance. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. Studies of the effect of irradiation in a nuclear reactor, of targets containing Mo used for the preparation of 99Mo gel, material that constitutes the 99Mo - 99mTc generators

    International Nuclear Information System (INIS)

    Nieto, Renata Correa

    2004-01-01

    The most used radioisotope in Nuclear Medicine is 99m Tc, obtained in the 99 Mo - 99m Tc generator form. 99 Mo can be produced by several nuclear reactions in Cyclotron and Reactor. The production in Cyclotron is not technically and commercially feasible. The production in Nuclear Reactor can be made in two ways: 235 U fission and 99 Mo (n,γ) 99 Mo reaction. A project aiming the production of 99 Mo by activation of Mo is under way at IPEN, producing a gel type MoZr generator. There are two ways of preparing the gel and the generators: by irradiating MoO 3 and preparing the gel or by the preparation of the gel and further irradiation. This work consists in the study of the irradiation effects in several targets containing Mo for the production of 99 Mo by the 98 Mo (n,γ) 99 Mo reaction and further preparation of the gel for use as a gel type 99 Mo - 99m Tc generator. Three rinds of gel were studied: zirconium, titanium and cerium molybdate, and their morphology, infrared structure and elution yield of 99m Tc were analysed. The best results were achieved with the generators prepared with MoZr post formed gel, with amorphous structure and better elution yields. The pre formed gel induced crystallinity and worst performance of the generators. (author)

  15. Sol-Gel Application for Consolidating Stone: An Example of Project-Based Learning in a Physical Chemistry Lab

    Science.gov (United States)

    de los Santos, Desiree´ M.; Montes, Antonio; Sa´nchez-Coronilla, Antonio; Navas, Javier

    2014-01-01

    A Project Based Learning (PBL) methodology was used in the practical laboratories of the Advanced Physical Chemistry department. The project type proposed simulates "real research" focusing on sol-gel synthesis and the application of the obtained sol as a stone consolidant. Students were divided into small groups (2 to 3 students) to…

  16. Sol–gel immobilization of Alcalase from Bacillus licheniformis for application in the synthesis of C-terminal peptide amides

    NARCIS (Netherlands)

    Corici, L.N.; Frissen, A.E.; Zoelen, van D.J.; Eggen, I.F.; Peter, F.; Davidescu, C.M.; Boeriu, C.G.

    2011-01-01

    Alcalase 2.4L FG, a commercial preparation of Subtilisin A, was physically entrapped in glass sol–gel matrices using alkoxysilanes of different types mixed with tetramethoxysilane (TMOS). The materials were used for catalyzing C-terminal amidation of Z-Ala-Phe-OMe in a mixture of tert-butanol/DMF.

  17. Preparation of continuous alumina gel fibres by aqueous sol–gel ...

    Indian Academy of Sciences (India)

    lowed by being heated in a water bath at 80. ◦. C. The proper amount of water and spinning additive (PVP) were added in the AL gel, and then the precursor sol was concentrated to obtain a spinning sol in the water bath (60 .... ing point phase (e.g. SiO2, B2O3, TiO2) (Minnesota Mining and Manufacturing Company 1977).

  18. Diffusion MRI for rectal cancer staging: ADC measurements before and after ultrasonographic gel lumen distension

    Energy Technology Data Exchange (ETDEWEB)

    Palmucci, S., E-mail: spalmucci@sirm.org; Piccoli, M.; Piana, S.; Foti, P.V.; Siverino, R.O.A.; Mauro, L.A.; Milone, P.; Ettorre, G.C.

    2017-01-15

    Objectives: To compare Apparent Diffusion Coefficient (ADC) measurements in rectal neoplastic lesions before and after lumen distension obtained with sonography transmission gel. Methods: From January 2014 to July 2016, 25 patients (average age 63.7, range 41–85, 18 males) were studied for pre-treatment rectal cancer staging using a 1.5 T MRI. Diffusion MRI was obtained using echo-planar imaging with b = 800 value; all patients were studied acquiring diffusion sequences with and without rectal lumen distension obtained using sonography transmission gel. In both diffusion sequences, two blinded readers calculated border ADC values and small ADC values, drawing regions of interest respectively along tumour borders and far from tumour borders. Mean ADC values among readers − for each type of ADC measurement − were compared using Wilcoxon matched pairs signed rank test. Correlation was assessed using Pearson analysis. Results: Border ADC mean value for diffusion MR sequences without endorectal contrast was 1.122 mm{sup 2}/sec, with 95% Confidence Interval (CI) = 1.02–1.22; using gel lumen distension, higher border ADC mean value of 1.269 mm{sup 2}/s (95% CI = 1.16–1.38) was obtained. Wilcoxon matched pairs signed rank test revealed statistical difference (p < 0.01); a strong Pearson correlation was reported, with r value of 0.69. Small-ADC mean value was 1.038 mm{sup 2}/s (95% CI = 0.91–1.16) for diffusion sequences acquired without endorectal distension and 1.127 mm{sup 2}/s (95% CI = 0.98–1.27) for diffusion sequences obtained after endorectal gel lumen distension. Wilcoxon analysis did not show statistical difference (p = 0.13). A very strong positive correlation was observed, with r value of 0.81. Conclusions: ADC measurements are slightly higher using endorectal sonographic transmission gel; ROI should be traced far from tumour borders, to minimize gel filled-pixel along the interface between lumen and lesion. Further studies are needed to

  19. In-gel digestion for mass spectrometric characterization of RNA from fluorescently stained polyacrylamide gels.

    Science.gov (United States)

    Taoka, Masato; Ikumi, Maki; Nakayama, Hiroshi; Masaki, Shunpei; Matsuda, Ryozo; Nobe, Yuko; Yamauchi, Yoshio; Takeda, Jun; Takahashi, Nobuhiro; Isobe, Toshiaki

    2010-09-15

    Although current mass spectrometry-based proteomics technology allows for high-throughput analysis of protein components in functional ribonucleoprotein complexes, this technology has had limited application to studies of RNA itself. Here we present a protocol for RNA analysis using polyacrylamide gel electrophoresis coupled with liquid chromatography-tandem mass spectrometry. Specifically, RNAs of interest are subjected to polyacrylamide gel electrophoresis and stained with a fluorescent dye, and RNAs in gel bands are digested with nuclease and then analyzed directly liquid chromatography-mass spectrometry, resulting in highly accurate mass values and reliable information on post-transcriptional modifications. We demonstrate that the method can be applied to the identification and chemical analysis of small RNAs in mouse embryonic stem cell extracts and of small RNAs in the spliceosomal ribonucleoprotein complex pulled down from yeast cells using a tagged protein cofactor as bait. The protocol is relatively simple and allowed us to identify not only three novel methylated nucleotide residues of RNase P RNA, U6 snRNA, and 7SL RNA prepared from mouse ES cells but also various 3'-end forms of U4, U5S, and U6 snRNAs isolated from the yeast spliceosome at the femtomole level. The method is thus a convenient tool for direct analysis of RNAs in various cellular ribonucleoprotein complexes, particularly for the analysis of post-transcriptional modifications and metabolic processing of RNA.

  20. Anaphylactoid reaction after use of intracervical dinoprostone gel.

    Science.gov (United States)

    Vaidya, Madhuri; Ghike, Sunita; Jain, Sheela

    2014-03-01

    Anaphylactic-like reaction or anaphylactoid reaction resembles generalized anaphylaxis but is not caused by immunoglobulin E-mediated allergic reaction. This reaction is caused by a non-immunologic mechanism even after first exposure to antigen. Prostaglandin E2 (dinoprostone) gel is commonly used for pre-induction cervical ripening. We report a case of anaphylactiod reaction after insertion of prostaglandin E2 gel for induction of labor. Hyperstimulation with dinoprostone gel is reported in the literature. An isolated report of three cases of anaphylactiod reaction after intracervical dinoprostone gel was found during a literature search. We are reporting this case for its rarity. As a potentially life-threatening condition, every obstetrician should be aware of this rare complication of dinoprostone gel.

  1. Molecular Gels Materials with Self-Assembled Fibrillar Networks

    CERN Document Server

    Weiss, Richard G

    2006-01-01

    Molecular gels and fibrillar networks – a comprehensive guide to experiment and theory Molecular Gels: Materials with Self-Assembled Fibrillar Networks provides a comprehensive treatise on gelators, especially low molecular-mass gelators (LMOGs), and the properties of their gels. The structures and modes of formation of the self-assembled fibrillar networks (SAFINs) that immobilize the liquid components of the gels are discussed experimentally and theoretically. The spectroscopic, rheological, and structural features of the different classes of LMOGs are also presented. Many examples of the application of the principal analytical techniques for investigation of molecular gels (including SANS, SAXS, WAXS, UV-vis absorption, fluorescence and CD spectroscopies, scanning electron, transmission electron and optical microscopies, and molecular modeling) are presented didactically and in-depth, as are several of the theories of the stages of aggregation of individual LMOG molecules leading to SAFINs. Several actua...

  2. Tetracaine gel vs EMLA cream for percutaneous anaesthesia in children

    DEFF Research Database (Denmark)

    Rømsing, Janne; Henneberg, S W; Walther-Larsen, S

    1999-01-01

    We have evaluated the anaesthetic effect of tetracaine gel 1 g, applied for 45 min, compared with EMLA cream 2 g, applied for 60 min, in a randomized, double-blind study in 60 children aged 3-15 yr. Venous cannulation was performed 15 min after removal of the EMLA cream (n = 20) and tetracaine gel...... (n = 20). Cannulation was performed up to 215 min after removal of the tetracaine gel in another 20 patients. Significantly lower pain scores were recorded by the children treated with tetracaine gel compared with EMLA cream (P ... no pain compared with only 10% in the EMLA group. Only minor adverse effects were observed. We conclude that tetracaine gel provided effective, rapid, long-lasting and safe local anaesthesia, and was significantly better than EMLA cream in reducing pain during venous cannulation in children using...

  3. [Role of the i-gel in emergency airway management].

    Science.gov (United States)

    Ueshima, Hironobu; Asai, Takashi

    2014-04-01

    The i-gel is a relatively new supraglottic airway, which has been shown to be useful during general anesthesia, and it may have a potential role during cardiopulmonary resuscitation. In a manikin study, we have found that, compared with laryngeal mask airways, the i-gel was significantly easier and faster to insert, due mainly to no-necessity of cuff inflation. One possible difficulty in using the i-gel during cardiopulmonary resuscitation is that the device cannot be fixed with the Thomas Tube Holder (Laerdal Medical Japan KK, Tokyo, Japan). A specially tailored device for cardiopulmonary resuscitation, recently has become available. The pack includes the i-gel O2 (which has a side port for oxygen delivery), a suction catheter, a sachet containing lubrication jelly, and a fixation strap. We describe the role of the i-gel during emergency airway management.

  4. [Semisynthetic cellulose derivatives as the base of hydrophilic gel systems].

    Science.gov (United States)

    Bajerová, M; Gajdziok, J; Dvorácková, K; Masteiková, R; Kollár, P

    2008-04-01

    The field of drug technology widely ulilizes gel systems of high-molecular substances, which have a number of advantages, such as low toxicity, availability, unique physical properties, biocompatibility, mucoadhesivity, and others. Gel systems are used in the field of local as well as general therapy, in both shape-specific and shape-non-specific dosage forms, in medicaments of the first, second, and third generations. An important group of gels employed in pharmacy are hydrophilic gels or hydrogels, most frequently composed of hydrophilic polymers of natural, semisynthetic and synthetic origin. Though cellulose derivatives as the representatives of polymers of semisynthetic origin are used in pharmaceutical technology for a long time, their research continues and their other possible uses are being searched for. Their advantages include especially safety, easy availability, and a relatively low price. The review paper describes selected cellulose derivatives, their properties and uses in pharmaceutical technology with regard to their use in the field of production of gel systems.

  5. Adsorption Characteristics of Water and Silica Gel System for Desalination Cycle

    KAUST Repository

    Cevallos, Oscar R.

    2012-07-01

    An adsorbent suitable for adsorption desalination cycles is essentially characterized by a hydrophilic and porous structure with high surface area where water molecules are adsorbed via hydrogen bonding mechanism. Silica gel type A++ possesses the highest surface area and exhibits the highest equilibrium uptake from all the silica gels available in the market, therefore being suitable for water desalination cycles; where adsorbent’s adsorption characteristics and water vapor uptake capacity are key parameters in the compactness of the system; translated as feasibility of water desalination through adsorption technologies. The adsorption characteristics of water vapor onto silica gel type A++ over a temperature range of 30 oC to 60 oC are investigated in this research. This is done using water vapor adsorption analyzer utilizing a constant volume and variable pressure method, namely the Hydrosorb-1000 instrument by Quantachrome. The experimental uptake data is studied using numerous isotherm models, i. e. the Langmuir, Tóth, generalized Dubinin-Astakhov (D-A), Dubinin-Astakhov based on pore size distribution (PSD) and Dubinin-Serpinski (D-Se) isotherm for the whole pressure range, and for a pressure range below 10 kPa, proper for desalination cycles; isotherms type V of the International Union of Pure and Applied Chemistry (IUPAC) classification were exhibited. It is observed that the D-A based on PSD and the D-Se isotherm models describe the best fitting of the experimental uptake data for desalination cycles within a regression error of 2% and 6% respectively. All isotherm models, except the D-A based on PSD, have failed to describe the obtained experimental uptake data; an empirical isotherm model is proposed by observing the behavior of Tóth and D-A isotherm models. The new empirical model describes the water adsorption onto silica gel type A++ within a regression error of 3%. This will aid to describe the advantages of silica gel type A++ for the design of

  6. Pharmacokinetics of the Protein Microbicide 5P12-RANTES in Sheep following Single-Dose Vaginal Gel Administration.

    Science.gov (United States)

    McBride, John W; Dias, Nicola; Cameron, David; Offord, Robin E; Hartley, Oliver; Boyd, Peter; Kett, Vicky L; Malcolm, R Karl

    2017-10-01

    5P12-RANTES, a chemokine analogue that potently blocks the HIV CCR5 coreceptor, is being developed as both a vaginal and rectal microbicide for prevention of sexual transmission of HIV. Here, we report the first pharmacokinetic data for 5P12-RANTES following single-dose vaginal gel administration in sheep. Aqueous gel formulations containing low (1.24-mg/ml), intermediate (6.18-mg/ml), and high (32.0-mg/ml; suspension-type gel) concentrations of 5P12-RANTES were assessed via rheology, syringeability, and in vitro release testing. Following vaginal gel administration to sheep, 5P12-RANTES concentrations were measured in vaginal fluid, vaginal tissue, and serum over a 96-h period. All gels showed non-Newtonian pseudoplastic behavior, with the high-concentration gels exhibiting a greater viscosity and cohesive structure than the intermediate- and low-concentration gels. In in vitro release testing, >90% 5P12-RANTES was released from the low- and intermediate-concentration gels after 72 h. For the high-concentration gel, ∼50% 5P12-RANTES was detected, attributed to protein denaturation during lyophilization and/or subsequent solvation of the protein within the gel matrix. In sheep, 5P12-RANTES concentrations in vaginal fluid, vaginal tissue, and serum increased in a dose-dependent manner. The highest concentrations were measured in vaginal fluid (10 5 to 10 7 ng/ml), followed by vaginal tissue (10 4 to 10 6 ng/ml). Both of these concentration ranges are several orders of magnitude above the reported half-maximal inhibitory concentrations. The lowest concentration was measured in serum (<10 2 ng/ml). The 5P12-RANTES pharmacokinetic data are similar to those reported previously for other candidate microbicides. These data, coupled with 5P12-RANTES's potency at picomolar concentrations, its strong barrier to resistance, and the full protection that it was observed to provide in a rhesus macaque vaginal challenge model, support the continued development of 5P12-RANTES as

  7. Ion-Gel-Gated Graphene Optical Modulator with Hysteretic Behavior.

    Science.gov (United States)

    Kim, Jin Tae; Choi, Hongkyw; Choi, Yongsuk; Cho, Jeong Ho

    2018-01-17

    We propose a graphene-based optical modulator and comprehensively investigate its photonic characteristics by electrically controlling the device with an ion-gel top-gate dielectric. The density of the electrically driven charge carriers in the ion-gel gate dielectric plays a key role in tuning the optical output power of the device. The charge density at the ion-gel-graphene interface is tuned electrically, and the chemical potential of graphene is then changed to control its light absorption strength. The optical behavior of the ion-gel gate dielectric exhibits a large hysteresis which originates from the inherent nature of the ionic gel and the graphene-ion-gel interface and a slow polarization response time of ions. The photonic device is applicable to both TE- and TM-polarized light waves, covering two entire optical communication bands, the O-band (1.26-1.36 μm) and the C-band (1.52-1.565 μm). The experimental results are in good agreement with theoretically simulated predictions. The temporal behavior of the ion-gel-graphene-integrated optical modulator reveals a long-term modulation state because of the relatively low mobility of the ions in the ion-gel solution and formation of the electric double layer in the graphene-ion-gel interface. Fast dynamic recovery is observed by applying an opposite voltage gate pulse. This study paves the way to the understanding of the operational principles and future applications of ion-gel-gated graphene optical devices in photonics.

  8. Improved gel electrophoresis matrix for hydrophobic protein separation and identification.

    Science.gov (United States)

    Tokarski, Caroline; Fillet, Marianne; Rolando, Christian

    2011-03-01

    We propose an improved acrylamide gel for the separation of hydrophobic proteins. The separation strategy is based on the incorporation of N-alkylated and N,N'-dialkylated acrylamide monomers in the gel composition in order to increase hydrophobic interactions between the gel matrix and the membrane proteins. Focusing on the most efficient monomer, N,N'-dimethylacrylamide, the potentiality of the new matrix was evaluated on membrane proteins of the human colon HCT-116 cell line. Protein analysis was performed using an adapted analytical strategy based on FT-ICR tandem mass spectrometry. As a result of this comparative study, including advanced reproducibility experiments, more hydrophobic proteins were identified in the new gel (average GRAVY: -0.085) than in the classical gel (average GRAVY: -0.411). Highly hydrophobic peptides were identified reaching a GRAVY value up to 1.450, therefore indicating their probable locations in the membrane. Focusing on predicted transmembrane domains, it can be pointed out that 27 proteins were identified in the hydrophobic gel containing up to 11 transmembrane domains; in the classical gel, only 5 proteins containing 1 transmembrane domain were successfully identified. For example, multiple ionic channels and receptors were characterized in the hydrophobic gel such as the sodium/potassium channel and the glutamate or the transferrin receptors whereas they are traditionally detected using specific enrichment techniques such as immunoprecipitation. In total, membrane proteins identified in the classical gel are well documented in the literature, while most of the membrane proteins only identified on the hydrophobic gel have rarely or never been described using a proteomic-based approach. 2010 Elsevier Inc. All rights reserved.

  9. The effects of brushing on human enamel surface roughness after NaF gel and theobromine gel exposure

    Science.gov (United States)

    Mahardhika, A.; Noerdin, A.; Eriwati, Y. K.

    2017-08-01

    This study aimed to determine the effects of brushing on human enamel surface roughness after different exposure times of 200 mg/L theobromine gel (8, 16, and 32 minutes) and 2% NaF gel (16 minutes). Twenty-four human upper premolars were used and divided into four groups. Group 1 was exposed to 2% NaF gel for 16 minutes. In contrast, groups 2, 3, and 4 were exposed to 200 mg/L theobromine gel for 8 minutes, 16 minutes, and 32 minutes, and each group was then brushed for 9 minutes and 20 seconds. After the treatment, samples were tested using a surface roughness tester (Mitutoyo SJ 301, Japan). The Wilcoxon test showed significant changes (p theobromine gel or NaF gel and after brushing for 9 minutes and 20 seconds. It can be concluded that exposure to 200 mg/L theobromine gel or 2% NaF gel can soften the enamel surface and then increase roughness after brushing.

  10. Betahistine dihydrochloride transdermal delivery via optimized thermosensitive gels: percutaneous absorption evaluation using rat growth as a biomarker.

    Science.gov (United States)

    Elkomy, Mohammed Hassan; El-Menshawe, Shahira F; Ali, Adel Ahmed; Halawa, Abdelkhalik Ali; El-Din, Ahmed S G Srag

    2018-02-01

    The aim of this study was to develop and optimize a betahistine dihydrochloride (BH) thermoreversible bioadhesive gel intended for transdermal delivery. The gels were obtained via cold method. A full factorial design was employed to investigate the joint effect of Poloxamer 407 concentration (18 and 20%), adhesive polymer type (Polyvinyl pyrolidone, Hydroxypropyl methylcellulose, and Carbopol 934), and adhesive polymer concentration (0.5 and 1.5%) on gelling temperature, viscosity at 37 °C, and adhesion strength. Data collected were analyzed using multiple linear regression. A desirability index approach with relative importance weight was used to choose the most desirable formulation. F4 (20% Poloxamer+1.5% Carbopol) was selected for further characterization. F4 released 96.97% drug in 12 h across hairless rat skin. F4 gelation temperature and time were 36 ± 0.35 °C, and 6 ± 0.7 min, respectively. F4 adhesive force was 8835.68 dyne/cm 2 . F4 was tested for its appetite suppressing effect in a rat model and it was evaluated histopathologically. Rats' chow intake and weight gain was significantly decreased with no signs of inflammation or lipolysis when the optimized BH gel formulation, F4, was compared with untreated animals and animals treated with BH free gel. The results suggest that BH is percutaneously absorbed from the gel base and that the BH gel is tolerable. The desirability index approach with relative importance weight of responses was effective in determination of the optimum formulation. BH is systemically effective and well-tolerated when applied topically in hydrogel-based systems. The Carbopol-Poloxamer gel is a promising modality for transdermal delivery of BH.

  11. Densification and crystallization of zirconia thin films prepared by sol-gel processing

    Energy Technology Data Exchange (ETDEWEB)

    Schwartz, R.W.; Voigt, J.A.; Buchheit, C.D.; Boyle, T.J.

    1993-12-31

    We have investigated the effects of precursor nature and heat treatment schedule on the densification and crystallization behavior of sol-gel derived zirconia thin films. Precursor solutions were prepared from n-propanol, zirconium (IV) n-propoxide, and either acetic acid, or 2,4-pentanedione (acac) and water additions. By controlling the ligand type and ligand-to-metal ratio, we were able to prepare films which displayed significant differences in densification behavior. We attribute the dissimilarity in densification to variations in the nature of the as-deposited films, as influenced by ligand type and concentration. While the acac- derived film was a physical gel, (i.e., a physical aggregation of the oligomeric species), the acetic acid-derived film, which exhibited less consolidation, was a chemical gel that could not be redissolved in the parent solvent. Films prepared with large acac/metal ratios and small water additions exhibited minimal crosslinking at 25{degree}C, displayed the greatest consolidation ({approximately}86% shrinkage) and the highest refractive index (n = 2.071) when heat treated. These results indicate the importance that M-O-M bonds (crosslinks) formed at low temperature can have on densification behavior. We also report on the effects of heat-treatment schedules and ramp rates on densification behavior. All of the films of the present study crystallized into the cubic phase, at temperatures ranging from {approximately}400{degree}C to greater than 700{degree}C, depending on the heating rate.

  12. Cheap glass fiber mats as a matrix of gel polymer electrolytes for lithium ion batteries.

    Science.gov (United States)

    Zhu, Yusong; Wang, Faxing; Liu, Lili; Xiao, Shiyin; Yang, Yaqiong; Wu, Yuping

    2013-11-12

    Lithium ion batteries (LIBs) are going to play more important roles in electric vehicles and smart grids. The safety of the current LIBs of large capacity has been remaining a challenge due to the existence of large amounts of organic liquid electrolytes. Gel polymer electrolytes (GPEs) have been tried to replace the organic electrolyte to improve their safety. However, the application of GPEs is handicapped by their poor mechanical strength and high cost. Here, we report an economic gel-type composite membrane with high safety and good mechanical strength based on glass fiber mats, which are separator for lead-acid batteries. The gelled membrane exhibits high ionic conductivity (1.13 mS cm(-1)), high Li(+) ion transference number (0.56) and wide electrochemical window. Its electrochemical performance is evaluated by LiFePO4 cathode with good cycling. The results show this gel-type composite membrane has great attraction to the large-capacity LIBs requiring high safety with low cost.

  13. Dosimetric evaluation of spectrophotometric response of alanine gel solution for gamma, photons, electrons and thermal neutrons radiations; Avaliacao dosimetrica da resposta espectrofotometrica da solucao gel de alanina para radiacao gama, de fotons, de eletrons e de neutrons termicos

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Cleber Feijo

    2009-07-01

    Alanine Gel Dosimeter is a new gel material developed at IPEN that presents significant improvement on Alanine system developed by Costa. The DL-Alanine (C{sub 3}H{sub 7}NO{sub 2}) is an amino acid tissue equivalent that improves the production of ferric ions in the solution. This work aims to analyse the main dosimetric characteristics this new gel material for future application to measure dose distribution. The performance of Alanine gel solution was evaluated to gamma, photons, electrons and thermal neutrons radiations using the spectrophotometry technique. According to the obtained results for the different studied radiation types, the reproducibility intra-batches and inter-batches is better than 4% and 5%, respectively. The dose response presents a linear behavior in the studied dose range. The response dependence as a function of dose rate and incident energy is better 2% and 3%, respectively. The lower detectable dose is 0.1 Gy. The obtained results indicate that the Alanine gel dosimeter presents good performance and can be useful as an alternative dosimeter in the radiotherapy area, using MRI technique for tridimensional dose distribution evaluation. (author)

  14. ANALISIS KEKUATAN GEL (GEL STRENGTH PRODUK PERMEN JELLY DARI GELATIN KULIT IKAN CUCUT DENGAN PENAMBAHAN KARAGINAN DAN RUMPUT LAUT

    Directory of Open Access Journals (Sweden)

    pipih - suptijah

    2014-06-01

    Full Text Available AbstrakPermen jelly merupakan permen bertekstur kenyal dengan penambahan komponen hidrokoloid,misalnya agar, gum, pektin, pati, karaginan, gelatin, dan lain-lain yang digunakan untuk modifi kasitekstur sehingga menghasilkan produk yang kenyal. Penelitian ini bertujuan menentukan kekuatan gel (gelstrength dan formulasi terbaik dari permen jelly yang berasal dari gelatin kulit ikan cucut dan karaginan.Metode analisis yang digunakan, meliputi analisis proksimat, pH, rendemen, viskositas, analisis sensori,dan kekuatan gel. Konsentrasi asam asetat terbaik dalam pembuatan gelatin adalah 0,1 N dan formulasipermen jelly terbaik terdapat pada permen jelly yang dibuat dari gelatin 1,75% dan karaginan 3,50% denganmenghasilkan kekuatan gel 169,35 N/cm2.Kata kunci: gelatin, ikan cucut, kekuatan gel (gel strength, permen jelly

  15. Silica Gel-Mediated Organic Reactions under Organic Solvent-Free Conditions

    Directory of Open Access Journals (Sweden)

    Satoaki Onitsuka

    2012-09-01

    Full Text Available Silica gel was found to be an excellent medium for some useful organic transformations under organic solvent-free conditions, such as (1 the Friedel-Crafts-type nitration of arenes using commercial aqueous 69% nitric acid alone at room temperature, (2 one-pot Wittig-type olefination of aldehydes with activated organic halides in the presence of tributyl- or triphenylphosphine and Hunig’s base, and (3 the Morita-Baylis-Hillman reaction of aldehydes with methyl acrylate. After the reactions, the desired products were easily obtained in good to excellent yields through simple manipulation.

  16. Comparison of Pseudomonas aeruginosa isolates from mink by serotyping and pulsed-field gel electrophoresis

    DEFF Research Database (Denmark)

    Hammer, Anne Sofie; Pedersen, Karl; Andersen, Thomas Holmen

    2003-01-01

    Isolates of Pseudomonas aeruginosa from clinical infections in mink were subjected to serotyping and pulsed-field gel electrophoresis (PFGE) using SpeI. A total of 212 isolates of P aeruginosa from the year 1998 to 2001 were included in this study: 168 isolates from mink obtained from 74 farm...... aeruginosa of specific PFGE types were found to cause clusters of outbreaks on several farms within a few weeks of each other. However, PFGE types of strains causing clusters of farm outbreaks changed from year to year. These results suggest that some outbreaks of haemorrhagic pneumonia are caused...

  17. Streptomyces levoris Immobilized on Silica Gel 60 as a Novel Biosorbent for Copper (II Preconcentration

    Directory of Open Access Journals (Sweden)

    Gergana K. Kirova

    2016-06-01

    Full Text Available In the present study dead Streptomyces levoris biomass loaded on silica gel 60 was applied as an eco-friendly solid phase extractor for copper (II preconcentration prior to its determination by flame atomic absorption spectrometry. The influences of different parameters such as pH of the sample solution, amount of solid phase, type and concentration of eluent, flow rate of sample solution, sample volume, and interfering effect of diverse ions on the preconcentration procedure were evaluated. An enrichment factor of 25 was achieved under optimum experimental conditions. The obtained results showed that Streptomyces levoris immobilized on silica gel can be considered as a promising new biosorbent for solid phase extraction of trace amounts of copper (II.

  18. Effectiveness Of 2% And 4% Papain Gels In The Healing Of Venous Ulcers

    Directory of Open Access Journals (Sweden)

    Andréa Pinto Leite Ribeiro

    2015-06-01

    Full Text Available OBJECTIVE To analyze the effectiveness of 2% and 4% papain gels in tissue repair of venous ulcers. METHOD Quasi-experimental study with consecutive sample of 16 patients with 30 venous ulcers treated at the outpatient clinic of a teaching hospital, from April to November in 2011, using a form for clinical assessment of the patient and its lesion. Variables were analyzed by Wilcoxon and McNemar test (p < 0.05. RESULTS Most participants were female; aged between 51 and 59 years; obese; with hypertension. Regarding ulcers, there was an average decrease of 7.9 cm2 (50% of its original size in 90 days; 20% of the ulcers completely healed within 56.67 days. There was an increase in epithelialization, significant reduction in the slough and edema, improved depth, in the type and amount of exudate (p < 0.0001. CONCLUSION 2% and 4% papain gels were effective in healing venous ulcers.

  19. Lidocaine gel vs lidocaine spray in reducing pain during insertion of the intrauterine contraceptive device.

    Science.gov (United States)

    Torky, Haitham; Moussa, Asem; El-Desouky, El-Sayed; Dief, Osama; Ahmed, Ali

    2017-04-01

    The aim of this study was to compare the pain-relieving effect of intracervical lidocaine gel with that of lidocaine spray or no local anaesthesia in decreasing pain during insertion of the intrauterine contraceptive device (IUCD). In a prospective multicentre non-randomised comparative study design, 420 women were divided into three groups of 140 and fitted with the same type of IUCD. Group 1 received cervical lidocaine gel, group 2 received cervical lidocaine spray and group 3 received no topical anaesthesia. A visual analogue scale was used to measure the degree of pain experienced. There were no significant differences between the three groups with regard to baseline characteristics such as age and number of deliveries. Significantly less pain was felt during cervical traction in women using a local anaesthetic. However, there were no significant differences in pain due to IUCD insertion. Application of a local anaesthetic decreased the pain resulting from cervical traction but not that resulting from IUCD insertion.

  20. Two-dimensional gel electrophoresis: glass tube-based IEF followed by SDS-PAGE.

    Science.gov (United States)

    Matsumoto, Hiroyuki; Haniu, Hisao; Kurien, Biji T; Komori, Naoka

    2012-01-01

    The genome information combined with data derived from modern mass spectrometry enables us to determine the identity of a protein once it is isolated from a complex mixture. Two-dimensional gel electrophoresis established more than three decades ago serves as a powerful protocol to isolate many proteins at once for such protein analysis. In the first two decades, the original procedure to use a glass tube-based isoelectric focusing (IEF) had been commonly used. Since an IEF in glass tubes is rather difficult to maneuver, a new method to use an IEF on a thin agarose slab backed by a plastic film (IPG Dry Strip) has been invented and is now widely used. In this chapter, we describe the original protocol that uses a glass tube-based IEF because, the capacity of protein loading and resolving power of this type of classic two-dimensional gel is still indispensible.

  1. Separation of yeast chromosome-sized DNAs by pulsed field gradient gel electrophoresis.

    Science.gov (United States)

    Schwartz, D C; Cantor, C R

    1984-05-01

    A new type of gel electrophoresis separates DNA molecules up to 2000 kb with resolutions exceeding the logarithmic molecular weight dependence of conventional electrophoresis. The technique uses 1.5% agarose, 10 to 20 micrograms of DNA per well, and low ionic strength buffers. It employs alternately pulsed, perpendicularly oriented electrical fields, at least one of which is inhomogeneous. The duration of the applied electrical pulses is varied from 1 sec to 90 sec to achieve optimal separations for DNAs with sizes from 30 to 2000 kb. This pulsed field gradient gel electrophoresis fractionates intact S. cerevisiae chromosomal DNA, producing a molecular karyotype that greatly facilitates the assignment of genes to yeast chromosomes. Each yeast chromosome consists of a single piece of DNA; the chromosome sizes are consistent with the genetic linkage map. We also describe a general method for preparing spheroplasts, and cell lysates, without significant chromosomal DNA breakage.

  2. Ozonation and sol-gel method to obtain Cu/Cu O nanoparticles from cyanidation wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Soria A, M. J.; Puente S, D. M.; Carrillo P, F. R. [Universidad Autonoma de Coahuila, Facultad de Metalurgia, Carretera 57 Km 4.5, 25710 Monclova, Coahuila (Mexico); Garcia C, L. A. [Centro de Investigacion en Quimica Aplicada, Blvd. Enrique Reyna No. 140, Col. Los Pinos, 25253 Saltillo, Coahuila (Mexico); Velazquez S, J., E-mail: frrcarrillo@yahoo.com.mx [University of Texas at San Antonio, Department of Physics and Astronomy, San Antonio TX 78249 (United States)

    2015-07-01

    The extraction process of gold and silver by cyanidation generates large amounts of effluent which also contain contaminants such as cyanide and significant metal values such as copper. This paper presents the results of the removal and recovery of copper from ozonation treatment of a residual aqueous cyanide. The residual solution was treated by ozonation-precipitation to obtain a precipitate of copper. From this, copper nano composites obtained by Pechini modified sol-gel method were obtained. The compounds obtained were characterized by X-ray diffraction, showing a dependence of the type of compounds formed over time of ozonation and heat treatment of the gel. The particle size was measured by scanning electron microscopy and calculated by the Scherrer equation, being between 50 and 120 nm. (Author)

  3. Influence of colloidal silicon dioxide on gel strength, robustness, and adhesive properties of diclofenac gel formulation for topical application.

    Science.gov (United States)

    Lu, Zheng; Fassihi, Reza

    2015-06-01

    The objective of this study is to identify the extent of stiffness, adhesiveness, and thixotropic character of a three-dimensional gel network of a 1% diclofenac sodium topical gel formulation in the presence and absence of colloidal silicon dioxide (CSD) and assess its ease of application and adhesiveness using both objective and subjective analysis. The 1% diclofenac gel was mixed with different amounts of CSD (e.g., 0.5, 1, 2, 3, and 5% w/w) and allowed to equilibrate prior to testing. The texture analyzer in combination with a cone-cap assembly was used to objectively investigate the changes in spreadability and adhesiveness of the gel system before and after addition of CSD. Results indicate that an increase in pliability and adhesiveness at levels ≥2 to ≤5% w/w of CSD dispersed in the gel ensues. For subjective analysis, gels with (2% w/w) CSD and in the absence of CSD were uniformly applied to a 20-cm(2) (5 cm × 4 cm) surface area on the forearms of healthy volunteers and vehicle preferences by the volunteers regarding ease of application, durability on the skin, compliance, and feelings concerning its textural properties were assessed. It appears that changes in the gel formulation with the addition of CSD enhance gel viscosity and bonding to the skin. Results further show that changes in physical and rheological characteristics of gel containing 2% w/w CSD did not significantly change subject preferences for the gel preparations. These findings may help formulators to have additional options to develop more robust and cost-effective formulations.

  4. Fibroblasts and monocyte macrophages contract and degrade three-dimensional collagen gels in extended co-culture

    Directory of Open Access Journals (Sweden)

    Ertl Ronald F

    2001-09-01

    Full Text Available Abstract Background Inflammatory cells are believed to play a prominent role during tissue repair and remodeling. Since repair processes develop and mature over extended time frames, the present study was designed to evaluate the effect of monocytes and fibroblasts in prolonged culture in three-dimensional collagen gels. Methods Blood monocytes from healthy donors and human fetal lung fibroblasts were cast into type I collagen gels and maintained in floating cultures for three weeks. Results Fibroblast-mediated gel contraction was initially inhibited by the presence of monocytes (P P P 2 production was significantly increased by co-culture and its presence attenuated collagen degradation. Conclusion The current study, therefore, demonstrates that interaction between monocytes and fibroblasts can contract and degrade extracellular matrix in extended culture.

  5. Poly(vinyl alcohol)-borate hydro/cosolvent gels: viscoelastic properties, solubilizing power, and application to art conservation.

    Science.gov (United States)

    Carretti, Emiliano; Grassi, Scilla; Cossalter, Manuela; Natali, Irene; Caminati, Gabriella; Weiss, Richard G; Baglioni, Piero; Dei, Luigi

    2009-08-04

    We report the development of a new type of hydrogel in which a cosolvent has been added to the water component. The gel networks are based on the well-known poly(vinyl alcohol)-borate systems (PVA-borate). However, it is shown that the rheological and solubilizing properties of the hydrogels can be modified drastically by the addition of a cosolvent. The studies have focused on 1-propanol as the added liquid, although it is shown that others (propylene carbonate, 1-pentanol, cyclohexanone, and 2-butanol) are amenable to making modified hydrogels as well. In addition to the rheological measurements, the gels have been investigated by differential scanning calorimetry (free water index) and determination of their solubilizing power. Finally, the gels have been applied to clean and oxidized varnish (patina) from the surface of a XVI-XVII century oil-on-wood painting by Ludovico Cardi detto il Cigoli. The mode of cleaning by and removal of the PVA-borate water/1-propanol gel from the painted surface demonstrate several advantages over other gels used in art conservation.

  6. Dosimetric evaluation of spectrophotometric response of alanine gel solution for gamma, photons, electrons and thermal neutrons radiations

    International Nuclear Information System (INIS)

    Silva, Cleber Feijo

    2009-01-01

    Alanine Gel Dosimeter is a new gel material developed at IPEN that presents significant improvement on Alanine system developed by Costa. The DL-Alanine (C 3 H 7 NO 2 ) is an amino acid tissue equivalent that improves the production of ferric ions in the solution. This work aims to analyse the main dosimetric characteristics this new gel material for future application to measure dose distribution. The performance of Alanine gel solution was evaluated to gamma, photons, electrons and thermal neutrons radiations using the spectrophotometry technique. According to the obtained results for the different studied radiation types, the reproducibility intra-batches and inter-batches is better than 4% and 5%, respectively. The dose response presents a linear behavior in the studied dose range. The response dependence as a function of dose rate and incident energy is better 2% and 3%, respectively. The lower detectable dose is 0.1 Gy. The obtained results indicate that the Alanine gel dosimeter presents good performance and can be useful as an alternative dosimeter in the radiotherapy area, using MRI technique for tridimensional dose distribution evaluation. (author)

  7. Mesoscopic objects, porous layers and nanocomposites-Possibilities of sol-gel chemistry

    International Nuclear Information System (INIS)

    Piwonski, Ireneusz

    2009-01-01

    The goal of this study was to prepare mesoscopic objects, thin porous films and nanocomposite coatings with the use of sol-gel technique. Silica nanotubes, titania nanoparticles, porous titania and zirconia coatings as well as titania nanocomposites were successfully synthesized by changing the type of sol-gel precursor, sol composition and applying dip-coating deposition procedure in order to obtain thin films or coatings. All materials were visualized and characterized by the Atomic Force Microcscopy (AFM) technique. Moreover, characterization of titania nanocomposites was extended to the tribological tests performed by means of microtribometer operating in normal loads range of 30-100 mN. The AFM analysis of mesoscopic objects and nanoparticles showed that the diameter of synthesized silica nanotubes was 60-70 nm and the size of titania nanoparticles was 43 nm. In case of porous layers the pore size in titania and zirconia coatings oscillated between 100 and 240 nm, however their shape and distribution were irregular. Microtribological studies of nanocomposites revealed the moderate decrease of the coefficient of friction for samples containing 5, 15 and 5 wt.% of zirconia nanoparticles in titania coatings annealed at 100, 500 and 1000 deg. C respectively. An enhancement of antiwear properties was already observed for 1 wt.% of nanophase content, except the sample annealed at 500 deg. C. It was also found that the annealing at high temperatures is a primary factor which affects the reduction of friction and wear of titania coatings while the presence of nanoparticles has secondary effect. Investigations in this study carried out with the use of the AFM technique highlighted the potential and flexibility of sol-gel approach in designing of various types of advanced materials in a form of mesoscopic objects, porous coatings and composite layers. Results collected in this study clearly demonstrated that sol-gel technique can be applied effectively in preparation of

  8. Etodolac Containing Topical Niosomal Gel: Formulation Development and Evaluation

    Directory of Open Access Journals (Sweden)

    Gyati Shilakari Asthana

    2016-01-01

    Full Text Available The present study aimed to investigate the delivery potential of Etodolac (ETD containing topical niosomal gel. Niosomal formulations were prepared by thin film hydration method at various ratios of cholesterol and Span 60 and were evaluated with respect to particle size, shape, entrapment efficiency, and in vitro characteristics. Dicetyl phosphate (DCP was also added in the niosomal formulation. Mean particle size of niosomal formulation was found to be in the range of 2 μm to 4 μm. Niosomal formulation N2 (1 : 1 ratio of cholesterol and surfactant displayed good entrapment efficiency (96.72%. TEM analyses showed that niosomal formulation was spherical in shape. Niosomal formulation (N2 displayed high percentage of drug release after 24 h (94.91 at (1 : 1 ratio of cholesterol : surfactant. Further selected niosomal formulation was used to formulate topical gel and was characterized with respect to its various parameters such as pH, viscosity, spreadability, ex vivo study, and in vivo potential permeation. Ex vivo study showed that niosomal gel possessed better skin permeation study than the plain topical gel. Further in vivo study revealed good inhibition of inflammation in case of topical niosomal gel than plain gel and niosomal formulation. The present study suggested that topical niosomal gel formulations provide sustained and prolonged delivery of drug.

  9. Etodolac Containing Topical Niosomal Gel: Formulation Development and Evaluation.

    Science.gov (United States)

    Shilakari Asthana, Gyati; Asthana, Abhay; Singh, Davinder; Sharma, Parveen Kumar

    2016-01-01

    The present study aimed to investigate the delivery potential of Etodolac (ETD) containing topical niosomal gel. Niosomal formulations were prepared by thin film hydration method at various ratios of cholesterol and Span 60 and were evaluated with respect to particle size, shape, entrapment efficiency, and in vitro characteristics. Dicetyl phosphate (DCP) was also added in the niosomal formulation. Mean particle size of niosomal formulation was found to be in the range of 2 μm to 4 μm. Niosomal formulation N2 (1 : 1) ratio of cholesterol and surfactant displayed good entrapment efficiency (96.72%). TEM analyses showed that niosomal formulation was spherical in shape. Niosomal formulation (N2) displayed high percentage of drug release after 24 h (94.91) at (1 : 1) ratio of cholesterol : surfactant. Further selected niosomal formulation was used to formulate topical gel and was characterized with respect to its various parameters such as pH, viscosity, spreadability, ex vivo study, and in vivo potential permeation. Ex vivo study showed that niosomal gel possessed better skin permeation study than the plain topical gel. Further in vivo study revealed good inhibition of inflammation in case of topical niosomal gel than plain gel and niosomal formulation. The present study suggested that topical niosomal gel formulations provide sustained and prolonged delivery of drug.

  10. Gellan gum fluid gels for topical administration of diclofenac.

    Science.gov (United States)

    Mahdi, Mohammed H; Conway, Barbara R; Mills, Thomas; Smith, Alan M

    2016-12-30

    Diclofenac topical formulations are often preferred for drug administration to patients who experience serious GIT problems. Absorption of the drug through the skin, however, can be challenging due to the natural protective feature of the stratum corneum (SC). In this article, fluid gels prepared from gellan gum were explored as a topical drug delivery vehicle. Rheological analysis of the formulations showed that it was possible to produce a topical gel with a viscosity and the mechanical strength similar to that of the commercially available Voltaren ® gel using 1% w/w of a 50:50 low acyl/high acyl (LA/HA) gellan blend. Soft-tribology was used to assess the lubrication properties of gellan fluid gels. The lubrication of the gellan gum fluid gel formulations at high rubbing speeds was similar to the lubrication of the Voltaren ® gel. The use of gellan gum dramatically increased skin permeation of diclofenac when compared with the commercially available formulation and could be controlled by changing the gellan gum concentration and/or sodium ion concentration in the formulation. This study highlights the potential use of fluid gels that can be easily tuned to have physical properties suitable for topical formulations with the added advantage of increasing drug permeation. Copyright © 2016 Elsevier B.V. All rights reserved.

  11. Antibacterial Activity of Copaiba Oil Gel on Dental Biofilm.

    Science.gov (United States)

    Simões, Cláudia A C G; Conde, Nikeila C de Oliveira; Venâncio, Gisely N; Milério, Patrícia S L L; Bandeira, Maria F C L; da Veiga Júnior, Valdir F

    2016-01-01

    Amazonian biodiversity products that have been used for years in folk medicine, have emerged as feasible and promising alternatives for the inhibition of microorganisms in dental biofilm. Copaiba oil, a phytotherapic agent widely used by the Amazonian populations, is known for its antibacterial, anti-inflammatory, anesthetic, healing and antitumor medicinal properties. The aim of this study was to evaluate the in vitro antibacterial activity of copaiba oil (Copaifera multijuga) gel against strains of Streptococcus sp present in dental biofilm. The copaiba oil was obtained and the chemical components were identified. The oil emulsions were formulated and used with the Brain Heart Infusion agar diffusion method with strains of Streptococcus mitis, Streptococcus constellatus and Streptococcus salivarius isolated from patients as well as standard strains of S. mitis (ATCC903), S. mutans (ATCC10449), S. sanguinis (ATCC15300) and S. oralis (ATCC10557). The study groups were as follows: experimental copaiba oil gel, 1% chlorhexidine gel (positive control) and base gel (negative control). The seeded plates were incubated at 37ºC for 12, 24 and 48 hours, respectively. The results obtained were analyzed by Shapiro-Wilk and Friedman Tests (p<0.05) for non parametric data and the Tukey test was used for pH values with 5% level of significance. The experimental copaiba oil gel and 1% chlorhexidine gel showed antibacterial activity against the tested microorganisms. The copaiba oil gel demonstrated antibacterial activity against all the strains of Streptococcus sp tested, suggesting that it can be used for dental biofilm control.

  12. Pickering stabilized peptide gel particles as tunable microenvironments for biocatalysis.

    Science.gov (United States)

    Scott, Gary; Roy, Sangita; Abul-Haija, Yousef M; Fleming, Scott; Bai, Shuo; Ulijn, Rein V

    2013-11-19

    We demonstrate the preparation of peptide gel microparticles that are emulsified and stabilized by SiO2 nanoparticles. The gels are composed of aromatic peptide amphiphiles 9-fluorenylmethoxycarbonyldiphenylalanine (Fmoc-FF) coassembled with Fmoc-amino acids with different functional groups (S: serine; D: aspartic acid; K: lysine; and Y: tyrosine). The gel phase provides a highly hydrated matrix, and peptide self-assembly endows the matrix with tunable chemical environments which may be exploited to support and stabilize proteins. The use of Pickering emulsion to stabilize these gel particles is advantageous through avoidance of surfactants that may denature proteins. The performance of enzyme lipase B immobilized in pickering/gel microparticles with different chemical functionalities is investigated by studying transesterification in heptane. We show that the use of Pickering particles enhances the performance of the enzyme, which is further improved in gel-phase systems, with hydrophilic environment provided by Fmoc-FF/S giving rise to the best catalytic performance. The combination of a tunable chemical environment in gel phase and Pickering stabilization described here is expected to prove useful for areas where proteins are to be exploited in technological contexts such as biocatalysis and also in other areas where protein performance and activity are important, such as biosensors and bioinspired solar fuel devices.

  13. Azelaic acid 15% gel: in the treatment of papulopustular rosacea.

    Science.gov (United States)

    Frampton, James E; Wagstaff, Antona J

    2004-01-01

    Azelaic acid is a naturally occurring, straight-chain dicarboxylic acid which is effective in the treatment of rosacea, presumably on account of its anti-inflammatory properties. In randomized, double-blind, multicenter studies involving patients with moderate papulopustular facial rosacea, twice-daily topical application of azelaic acid 15% gel to the face was significantly more effective than twice-daily administration of either its vehicle (two studies) or metronidazole 0.75% gel (one study) in reducing inflammatory lesion counts and erythema severity. However, neither active treatment had a clinically discernable effect on telangiectasia. In all three studies, azelaic acid 15% gel recipients experienced continuous decreases in lesion counts and erythema throughout the 12- to 15-week treatment periods. However, the effects of metronidazole 0.75% gel plateauxed after 8 weeks. In other efficacy assessments in these studies, azelaic acid 15% gel was superior to its vehicle and metronidazole 0.75% gel in both the investigators' global assessment of rosacea and the investigators' end-of-study evaluation of overall improvement, and superior to its vehicle in the patients' end-of-study evaluation of overall improvement. The most frequent treatment-related cutaneous adverse events during administration of azelaic acid 15% gel include burning/stinging/tingling and pruritus (itching); however, these events are predominantly transient in nature and mild-to-moderate in intensity.

  14. Emdogain-gel stimulates proliferation of odontoblasts and osteoblasts.

    Science.gov (United States)

    Jiang, Jin; Goodarzi, Golnaz; He, Jianing; Li, Haitao; Safavi, Kamran E; Spångberg, Larz S W; Zhu, Qiang

    2006-11-01

    The purpose of this study was to determine whether a premixed form of enamel matrix derivative (EMD), Emdogain-gel, has the same property as the original formula of EMD in stimulating the proliferation of osteoblasts and odontoblasts. Osteoblast cell line (MC3T3) and odontoblast cell line (MDPC) were cultured in the 6-well culture plates and treated in 4 different groups: (1) culture medium control, (2) 100 microg/mL Emdogain-gel directly added to the culture medium, (3) culture medium with a culture plate insert, and (4) 100 microg/mL Emdogain-gel added onto a culture plate insert. The culture plate insert prevented direct contact between Emdogain-gel and the cells. After 3-day incubation, cell morphology was examined and the total cell number per well was counted. Data were analyzed using 1-way ANOVA. Emdogain-gel significantly increased cell number of both osteoblasts and odontoblasts regardless the presence of the culture plate insert. Emdogain-gel stimulates cell proliferation of odontoblasts and osteoblasts. The direct contact between Emdogain-gel and cells is not required. Heat treatment of EMD and premix with propylene glycol alginate did not change its property of releasing bioactive molecules for promoting cell proliferation.

  15. Gel adsorption processing for waste solidification in NZP ceramics

    International Nuclear Information System (INIS)

    Yang, L.J.; Komareni, S.; Roy, R.

    1984-01-01

    Simulated PW-4b waste solution along with Na additive was mixed with Zr-P-O gel, dried and then fired to form the desired sodium zirconium phosphate, NaZr 2 (PO 4 ) 3 [NZP] ceramic. NZP and monazite were the only phases produced upon firing at 900 0 C with 10 to 40% of PW-4b mixed with the gel. CsZr 2 (PO 4 ) 3 which is isostructural with NZP was also identified when fired under reducing conditions. The -200 mesh powders of these waste forms prepared under reducing conditions showed excellent leach resistance under hydro-thermal conditions. Alternatively, PW-4b and Three Mile Island (TMI) wastes were adsorbed on Zr-P-O gel in a column. The gel was dried, pelletized and fired to form the desired [NZP] ceramic. Cesium was found to be selective on the Zr-P-O gel because no breakthrough of Cs was detected up to 38 column volumes of TMI waste. Thus, it is possible to use a tailored gel to sorb Cs and/or Sr from accident waste water and then fire the bed to form the [NZP] ceramic below 1000 0 C. The main advantages of the gel adsorption process are its simplicity and its enormous compositional flexibility. 12 references, 2 figures, 4 tables

  16. Western Blot of Stained Proteins from Dried Polyacrylamide Gels

    Science.gov (United States)

    Gruber, Claudia; Stan-Lotter, Helga

    1996-01-01

    Western blotting of proteins is customarily performed following their separation on polyacrylamide gels, either prior to staining (1) or, as recently reported, following staining (2). We describe here Western blotting with stained gels, which had been dried and some of which had been stored for years. This procedure permits immunological analysis of proteins, to which antisera may have become available only later, or where the application of newly developed sensitive detection methods is desired. Once rehydration of the gels is achieved, proteins can be-transferred to blotting membranes by any appropriate protocol. Proteins stained with Coomassie Blue have to be detected with a non-chromogenic method, such as the film-based enhanced chemiluminescence (ECL)2) procedure (3). Silver stained proteins, which transfer in the colorless form, may be visualized by any detection method, although, because of the usually very low amounts of proteins, detection by ECL is preferable. Blotting of stained proteins from rehydrated gels is as rapid and as quantitative as from freshly prepared gels, in contrast to blotting from wet stained gels, which requires extensive washing and results in low transfer efficiency (2). Together with a photographic record of the gel pattern, unambiguous identification of immunoreactive proteins from complex mixtures is possible. Some further applications of this work are discussed.

  17. Gels composed of sodium-aluminum silicate, Lake Magadi, Kenya

    Science.gov (United States)

    Eugster, H.P.; Jones, B.F.

    1968-01-01

    Sodium-aluminum silicate gels are found in surftcial deposits as thick as 5 centimeters in the Magadi area of Kenya. Chemical data indicate they are formed by the interaction of hot alkaline springwaters (67?? to 82??C; pH, about 9) with alkali trachyte flows and their detritus, rather than by direct precipitation. In the process, Na2O is added from and silica is released to the saline waters of the springs. Algal mats protect the gels from erosion and act as thermal insulators. The gels are probably yearly accumulates that are washed into the lakes during floods. Crystallization of these gels in the laboratory yields analcite; this fact suggests that some analcite beds in lacustrine deposits may have formed from gels. Textural evidence indicates that cherts of rocks of the Pleistocene chert series in the Magadi area may have formed from soft sodium silicate gels. Similar gels may have acted as substrates for the accumulation and preservation of prebiological organic matter during the Precambrian.

  18. The chemistry of plutonium in sol-gel processes

    International Nuclear Information System (INIS)

    Lloyd, M.H.; Haire, R.G.

    1978-01-01

    Studies of plutonium chemical behavior conducted in conjunction with plutonia sol-gel process development at ORNL are described. The colloidal solutions produced consist of 'Pu(IV) polymer,' and this is therefore the study of polymeric plutonium behavior. Spectrophotometric, electron diffraction, and electron microscopy studies, in addition to specific studies that were concerned with the colloidal behavior of Pu(IV) polymer, indicate several characteristics of polymer that are not generally recognized. The particle nature of Pu(IV) polymer indicated by electron microscopy, the amorphous-crystalline characteristics of primary polymer particles demonstrated by electron diffraction, and the reversible and irreversible aggregation of the primary particles shown by spectrophotometric techniques present a useful view of the nature of Pu(IV) polymer that has been helpful in solving or understanding various types of processing problems involving plutonium hydrolytic behavior. The colloidal characteristics of Pu(IV) polymer and crystallite growth of primary polymer particles by thermal denitration are also described. (orig.) [de

  19. An apparatus for submerged gel electrophoresis.

    Science.gov (United States)

    Kozulić, B; Heimgartner, U

    1991-11-01

    A novel apparatus for submerged gel electrophoresis is described in detail. It includes an upper buffer compartment, a lower buffer compartment, and a horizontal plate between the two compartments. The horizontal plate is a heat exchanger connected to an external heater/cooler. Buffer circulates between the two compartments through openings in the horizontal plate. In the upper compartment two separated openings are positioned on each side of the horizontal plate between the side walls and long vertical barriers. The barriers initially direct the flow of buffer and define the electric field on the sides of the upper compartment. The electric field is confined essentially into a rectangular box, defined on the ends by the end walls, on the sides by the barriers, on the bottom by the cooling plate, and on the top by the air. Since the volume of buffer is smaller in the electrode compartment than in the reservoir under the cooling plate, this design enables formation of a substantially uniform electric field without creating too high a current. To enhance uniformity of the electric field, anode and cathode consist each of two platinum wires positioned one above the other at a distance of 6 mm. The electrodes can be placed parallel to the sides and perpendicular to the buffer flow or parallel to the ends and the flow of buffer. The stream of buffer in the upper compartment is regulated by two dams, perpendicular to the long barriers, on each end of the horizontal plate.(ABSTRACT TRUNCATED AT 250 WORDS)

  20. Implementation of MRI gel dosimetry in radiation therapy

    International Nuclear Information System (INIS)

    Baeck, S.Aa.J.

    1998-12-01

    Gel dosimetry was used together with magnetic resonance imaging (MRI) to measure three-dimensional absorbed dose distributions in radiation therapy. Two different dosimeters were studied: ferrous- and monomer gel, based on the principles of radiation-induced oxidation and polymerisation, respectively. Single clinical electron and photon beams were evaluated and gel dose distributions were mainly within 2% of conventional detector results. The ferrous-gel was also used for clinical proton beams. A decrease in signal per absorbed dose was found close to the end of the range of the protons (15-20%). This effect was explained as a linear energy transfer dependence, further supported with Monte Carlo simulations. A method for analysing and comparing data from treatment planning system (TPS) and gel measurements was developed. The method enables a new pixel by pixel evaluation, isodose comparison and dose volume histogram verification. Two standard clinical radiation therapy procedures were examined using the developed TPS verification method. The treatment regimes included several beams of different radiation qualities. The TPS calculated data were in very good agreement with the dose distribution measured by the ferrous-gel. However, in a beam abutment region, larger dose difference was found. Beam adjustment errors and a minor TPS underestimation of the lateral scatter contribution outside the primary electron beam may explain the discrepancy. The overall uncertainty in the ferrous-gel dose determination was considerably reduced using an optimised MRI acquisition protocol and a new MRI scanner. The relative dose uncertainty was found to be better than 3.3% for all dose levels (95% confidence level). Using the method developed for comparing measured gel data with calculated treatment plans, the gel dosimetry method was proven to be a useful tool for radiation treatment planning verification