WorldWideScience

Sample records for two-phase systems atps

  1. Microfluidic generation of aqueous two-phase system (ATPS) droplets by controlled pulsating inlet pressures.

    Science.gov (United States)

    Moon, Byeong-Ui; Jones, Steven G; Hwang, Dae Kun; Tsai, Scott S H

    2015-06-07

    We present a technique that generates droplets using ultralow interfacial tension aqueous two-phase systems (ATPS). Our method combines a classical microfluidic flow focusing geometry with precisely controlled pulsating inlet pressure, to form monodisperse ATPS droplets. The dextran (DEX) disperse phase enters through the central inlet with variable on-off pressure cycles controlled by a pneumatic solenoid valve. The continuous phase polyethylene glycol (PEG) solution enters the flow focusing junction through the cross channels at a fixed flow rate. The on-off cycles of the applied pressure, combined with the fixed flow rate cross flow, make it possible for the ATPS jet to break up into droplets. We observe different droplet formation regimes with changes in the applied pressure magnitude and timing, and the continuous phase flow rate. We also develop a scaling model to predict the size of the generated droplets, and the experimental results show a good quantitative agreement with our scaling model. Additionally, we demonstrate the potential for scaling-up of the droplet production rate, with a simultaneous two-droplet generating geometry. We anticipate that this simple and precise approach to making ATPS droplets will find utility in biological applications where the all-biocompatibility of ATPS is desirable.

  2. High-throughput downstream process development for cell-based products using aqueous two-phase systems (ATPS) - A case study.

    Science.gov (United States)

    Zimmermann, Sarah; Scheeder, Christian; Zimmermann, Philipp K; Bogsnes, Are; Hansson, Mattias; Staby, Arne; Hubbuch, Jürgen

    2017-02-01

    The availability of preparative-scale downstream processing strategies for cell-based products presents a critical juncture between fundamental research and clinical development. Aqueous two-phase systems (ATPS) present a gentle, scalable, label-free, and cost-effective method for cell purification, and are thus a promising tool for downstream processing of cell-based therapeutics. Here, the application of a previously developed robotic screening platform that enables high-throughput cell partitioning analysis in ATPS is reported. In the present case study a purification strategy for two model cell lines based on high-throughput screening (HTS)-data and countercurrent distribution (CCD)-modeling, and validated the CCD-model experimentally is designed. The obtained data are shown an excellent congruence between CCD-model and experimental data, indicating that CCD-models in combination with HTS-data are a powerful tool in downstream process development. Finally, the authors are shown that while cell cycle phase significantly influences cell partitioning, cell type specific differences in surface properties are the main driving force in charge-dependent separation of HL-60 and L929 cells. In order to design a highly robust purification process it is, however, advisable to maintain constant growth conditions. Copyright © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. Two-phase flow in refrigeration systems

    CERN Document Server

    Gu, Junjie; Gan, Zhongxue

    2013-01-01

    Two-Phase Flow in Refrigeration Systems presents recent developments from the authors' extensive research programs on two-phase flow in refrigeration systems. This book covers advanced mass and heat transfer and vapor compression refrigeration systems and shows how the performance of an automotive air-conditioning system is affected through results obtained experimentally and theoretically, specifically with consideration of two-phase flow and oil concentration. The book is ideal for university postgraduate students as a textbook, researchers and professors as an academic reference book, and b

  4. Ionic liquids for two-phase systems and their application for purification, extraction and biocatalysis.

    Science.gov (United States)

    Oppermann, Sebastian; Stein, Florian; Kragl, Udo

    2011-02-01

    The development of biotechnological processes using novel two-phase systems based on molten salts known as ionic liquids (ILs) got into the focus of interest. Many new approaches for the beneficial application of the interesting solvent have been published over the last years. ILs bring beneficial properties compared to organic solvents like nonflammability and nonvolatility. There are two possible ways to use the ILs: first, the hydrophobic ones as a substitute for organic solvents in pure two-phase systems with water and second, the hydrophilic ones in aqueous two-phase systems (ATPS). To effectively utilise IL-based two-phase systems or IL-based ATPS in biotechnology, extensive experimental work is required to gain the optimal system parameters to ensure selective extraction of the product of interest. This review will focus on the most actual findings dealing with the basic driving forces for the target extraction in IL-based ATPS as well as presenting some selected examples for the beneficial application of ILs as a substitute for organic solvents. Besides the research focusing on IL-based two-phase systems, the "green aspect" of ILs, due to their negligible vapour pressure, is widely discussed. We will present the newest results concerning ecotoxicity of ILs to get an overview of the state of the art concerning ILs and their utilisation in novel two-phase systems in biotechnology.

  5. Selective separation and enrichment of proteins in aqueous two-phase extraction system

    Institute of Scientific and Technical Information of China (English)

    Feng Qu; Hao Qin; Min Dong; Dong Xu Zhao; Xin Ying Zhao; Jing Hua Zhang

    2009-01-01

    A simple aqueous two-phase extraction system(ATPS)of PEG/phosphate was proposed for selective separation and enrichment of proteins.The combination of ATPE with HPLC was applied to identify the partition of proteins in two phases.Five proteins (bovine serum albumin,Cytochrome C,lysozyme,myoglobin,and trypsin)were used as model proteins to study the effect of phosphate concentration and pH on proteins partition.The PEG/phosphate system was firstly applied to real human saliva and plasma samples,some proteins showed obviously different partition in two phases.The primary results manifest the selective separation and enrichment of proteins in ATPS provided the potential for high abundance proteins depletion in proteomics.

  6. Affinity partitioning of human antibodies in aqueous two-phase systems

    NARCIS (Netherlands)

    Rosa, P. A. J.; Azevedo, A. M.; Ferreira, I. F.; de Vries, J.; Korporaal, R.; Verhoef, H. J.; Visser, T. J.; Aires-Barros, M. R.

    2007-01-01

    The partitioning of human immunoglobulin (IgG) in a polymer-polymer and polymer-salt aqueous two-phase system (ATPS) in the presence of several functionalised polyethylene glycols (PEGs) was studied. As a first approach, the partition studies were performed with pure IgG using systems in which the t

  7. Scaling of Two-Phase Systems Across Gravity Levels Project

    Data.gov (United States)

    National Aeronautics and Space Administration — There is a defined need for long term earth based testing for the development and deployment of two-phase flow systems in reduced-gravity, including lunar gravity,...

  8. Ultralow interfacial tensions of aqueous two-phase systems measured using drop shape.

    Science.gov (United States)

    Atefi, Ehsan; Mann, J Adin; Tavana, Hossein

    2014-08-19

    Aqueous solutions of different polymers can separate and form aqueous two-phase systems (ATPS). ATPS provide an aqueous, biocompatible, and mild environment for separation and fractionation of biomolecules. The interfacial tension between the two aqueous phases plays a major role in ATPS-mediated partition of biomolecules. Because of the structure of the two aqueous phases, the interfacial tensions between the phases can be 3-4 orders of magnitude smaller than conventional fluid-liquid systems: ∼1-100 μJ/m(2) for ATPS compared to ∼72 mJ/m(2) for the water-vapor interface. This poses a major challenge for the experimental measurements of reproducible interfacial tension data for these systems. We address the need for precise determination of ultralow interfacial tensions by systematically studying a series of polymeric ATPS comprising of polyethylene glycol (PEG) and dextran (DEX) as the phase-forming polymers. Sessile and pendant drops of the denser DEX phase are formed within the immersion PEG phase. An axisymmetric drop shape analysis (ADSA) is used to determine interfacial tensions of eight different ATPS. Specific criteria are used to reproducibly determine ultralow interfacial tensions of the ATPS from pendant and sessile drops. Importantly, for a given ATPS, pendant drop and sessile drop experiments return values within 0.001 mJ/m(2) indicating reliability of our measurements. Then, the pendant drop technique is used to measure interfacial tensions of all eight ATPS. Our measured values range from 0.012 ± 0.001 mJ/m(2) to 0.381 ± 0.006 mJ/m(2) and vary with the concentration of polymers in equilibrated phases of ATPS. Measurements of ultralow interfacial tensions with such reproducibility will broadly benefit studies involving partition of different biomolecules in ATPS and elucidate the critical effect of interfacial tension.

  9. Interfacial Tension Effect on Cell Partition in Aqueous Two-Phase Systems.

    Science.gov (United States)

    Atefi, Ehsan; Joshi, Ramila; Mann, Jay Adin; Tavana, Hossein

    2015-09-30

    Aqueous two-phase systems (ATPS) provide a mild environment for the partition and separation of cells. We report a combined experimental and theoretical study on the effect of interfacial tension of polymeric ATPS on the partitioning of cells between two phases and their interface. Two-phase systems are generated using polyethylene glycol and dextran of specific properties as phase-forming polymers and culture media as the solvent component. Ultralow interfacial tensions of the solutions are precisely measured using an axisymmetric drop shape analysis method. Partition experiments show that two-phase systems with an interfacial tension of 30 μJ/m(2) result in distribution of majority of cells to the bottom dextran phase. An increase in the interfacial tension results in a distribution of cells toward the interface. An independent cancer cell spheroid formation assay confirms these observations: a drop of the dextran phase containing cancer cells is dispensed into the immersion polyethylene glycol phase to form a cell-containing drop. Only at very small interfacial tensions do cells remain within the drop to aggregate into a spheroid. We perform a thermodynamic modeling of cell partition to determine variations of free energy associated with displacement of cells in ATPS with respect to the ultralow interfacial tensions. This modeling corroborates with the experimental results and demonstrates that at the smallest interfacial tension of 30 μJ/m(2), the free energy is a minimum with cells in the bottom phase. Increasing the interfacial tension shifts the minimum energy and partition of cells toward the interfacial region of the two aqueous phases. Examining differences in the partition behavior and minimum free energy modeling of A431.H9 cancer cells and mouse embryonic stem cells shows that the surface properties of cells further modulate partition in ATPS. This combined approach provides a fundamental understanding of interfacial tension role on cell partition in

  10. Rapid RNA Exchange in Aqueous Two-Phase System and Coacervate Droplets

    Science.gov (United States)

    Jia, Tony Z.; Hentrich, Christian; Szostak, Jack W.

    2014-02-01

    Compartmentalization in a prebiotic setting is an important aspect of early cell formation and is crucial for the development of an artificial protocell system that effectively couples genotype and phenotype. Aqueous two-phase systems (ATPSs) and complex coacervates are phase separation phenomena that lead to the selective partitioning of biomolecules and have recently been proposed as membrane-free protocell models. We show in this study through fluorescence recovery after photobleaching (FRAP) microscopy that despite the ability of such systems to effectively concentrate RNA, there is a high rate of RNA exchange between phases in dextran/polyethylene glycol ATPS and ATP/poly-L-lysine coacervate droplets. In contrast to fatty acid vesicles, these systems would not allow effective segregation and consequent evolution of RNA, thus rendering these systems ineffective as model protocells.

  11. Partitioning in aqueous two-phase systems: Analysis of strengths, weaknesses, opportunities and threats.

    Science.gov (United States)

    Soares, Ruben R G; Azevedo, Ana M; Van Alstine, James M; Aires-Barros, M Raquel

    2015-08-01

    For half a century aqueous two-phase systems (ATPSs) have been applied for the extraction and purification of biomolecules. In spite of their simplicity, selectivity, and relatively low cost they have not been significantly employed for industrial scale bioprocessing. Recently their ability to be readily scaled and interface easily in single-use, flexible biomanufacturing has led to industrial re-evaluation of ATPSs. The purpose of this review is to perform a SWOT analysis that includes a discussion of: (i) strengths of ATPS partitioning as an effective and simple platform for biomolecule purification; (ii) weaknesses of ATPS partitioning in regard to intrinsic problems and possible solutions; (iii) opportunities related to biotechnological challenges that ATPS partitioning may solve; and (iv) threats related to alternative techniques that may compete with ATPS in performance, economic benefits, scale up and reliability. This approach provides insight into the current status of ATPS as a bioprocessing technique and it can be concluded that most of the perceived weakness towards industrial implementation have now been largely overcome, thus paving the way for opportunities in fermentation feed clarification, integration in multi-stage operations and in single-step purification processes.

  12. Influence of system and process parameters on partitioning of cheese whey proteins in aqueous two-phase systems.

    Science.gov (United States)

    Rito-Palomares, M; Hernandez, M

    1998-06-26

    A practical study is described to characterise some problems encountered in the application of aqueous two-phase systems (ATPS) to protein recovery. These factors include practical design of extraction stages and the impact of ATPS compounding methods and biological suspension upon process performance. They were addressed using the recovery of whey proteins as a model. The known effects of system parameters (i.e. tie-line length, volume ratio and system pH) were exploited to define the specific operating conditions of a two-stage ATPS process for the recovery of whey proteins. The partition of whey proteins in ATPS assembled using different methods resulted in changes in the partition coefficient of the proteins. Such changes were associated with the initial location of the proteins in the polymer or salt-rich solutions of the ATPS. Cheese whey loaded into the ATPS caused the displacement of the binodal curve from the origin. Such behaviour was attributed to the residual fat present in the whey. These findings highlight those factors perceived as negative constraints on the wider adoption of ATPS processes for protein recovery from complex biological systems.

  13. Recovery of crocins from saffron stigmas (Crocus sativus) in aqueous two-phase systems.

    Science.gov (United States)

    Montalvo-Hernández, Bertha; Rito-Palomares, Marco; Benavides, Jorge

    2012-05-04

    Crocins are carotenoid derivates that have recently attracted the interest of the scientific community due to their nutraceutical properties. Saffron (dry Crocus sativus stigmas) is one of the main known sources of crocins. In this study the potential use of aqueous two-phase system (ATPS) for the extraction of crocins from C. sativus stigmas was evaluated. The partitioning behavior of crocins in different types of ATPS (polymer-polymer, polymer-salt, alcohol-salt and ionic liquid-salt) was evaluated. Ethanol-potassium phosphate ATPS were selected based on their high top phase recovery yield and low cost of system constituents. The evaluation and optimization of system parameters rendered conditions (V(R)=3.2, ethanol 19.8% (w/w), potassium phosphate 16.5% (w/w), TLL of 25% (w/w), 0.1M NaCl and 2% (w/w) of sample load) under which more than 75% of total crocins were recovered in the top (ethanol rich) phase, whereas the wasted stigmas accumulated in the bottom phase. Lastly, a comparison between an optimized solid-liquid extraction using ethanol:water as solvent and ATPS was conducted demonstrating that similar yields are achieved with both strategies (76.89 ± 18% and 79.27 ± 1.6%, respectively). However, ATPS rendered a higher extraction selectivity of 1.3 ± 0.04 mg of crocins for each mg of phenolic compound, whereas ethanolic extraction showed a selectivity of 0.87 ± 0.01. The results reported herein demonstrate the potential application of ATPS, particularly ethanol-potassium phosphate systems, for the recovery of crocins from C. sativus stigmas.

  14. Two-phase flow instability in a parallel multichannel system

    Institute of Scientific and Technical Information of China (English)

    HOU Suxia

    2009-01-01

    The two-phase flow instabilities observed in through parallel multichannel can be classified into three types, of which only one is intrinsic to parallel multichannel systems. The intrinsic instabilities observed in parallel multichannel system have been studied experimentally. The stable boundary of the flow in such a parallel-channel system are sought, and the nature of inlet flow oscillation in the unstable region has been examined experimentally under various conditions of inlet velocity, heat flux, liquid temperature, cross section of channel and entrance throttling. The results show that parallel multichannel system possess a characteristic oscillation that is quite independent of the magnitude and duration of the initial disturbance, and the stable boundary is influenced by the characteristic frequency of the system as well as by the exit quality when this is low, and upon raising the exit quality and reducing the characteristic frequency, the system increases its instability, and entrance throttling effectively contributes to stabilization of the system.

  15. Design of aqueous two-phase systems supporting animal cell growth: a first step toward extractive bioconversions.

    NARCIS (Netherlands)

    Zijlstra, G.M.; Gooijer, de C.D.; Pol, van der L.A.; Tramper, J.

    1996-01-01

    The design of aqueous two-phase systems (ATPSs) which support the long-term growth of animal cells is described in this paper. It was found that the increase in osmolality caused by the ATPS-forming polymers could be compensated by reducing the NaCl concentration of the culture medium. Cell growth

  16. A TWO-PHASE APPROACH TO FUZZY SYSTEM IDENTIFICATION

    Institute of Scientific and Technical Information of China (English)

    Ta-Wei HUNG; Shu-Cherng FANG; Henry L.W.NUTTLE

    2003-01-01

    A two-phase approach to fuzzy system identification is proposed. The first phase produces a baseline design to identify a prototype fuzzy system for a target system from a coIlection of input-output data pairs. It uses two easily implemented clustering techniques: the subtractive clustering method and the fuzzy c-means (FCM) clustering algorithm. The second phase (fine tuning)is executed to adjust the parameters identified in the baseline design. This phase uses the steepest descent and recursive least-squares estimation methods. The proposed approach is validated by applying it to both a function approximation type of problem and a classification type of problem. An analysis of the learning behavior of the proposed approach for the two test problems is conducted for further confirmation.

  17. Transient thermohydraulic modeling of two-phase fluid systems

    Science.gov (United States)

    Blet, N.; Delalandre, N.; Ayel, V.; Bertin, Y.; Romestant, C.; Platel, V.

    2012-11-01

    This paper presents a transient thermohydraulic modeling, initially developed for a capillary pumped loop in gravitational applications, but also possibly suitable for all kinds of two-phase fluid systems. Using finite volumes method, it is based on Navier-Stokes equations for transcribing fluid mechanical aspects. The main feature of this 1D-model is based on a network representation by analogy with electrical. This paper also proposes a parametric study of a counterflow condenser following the sensitivity to inlet mass flow rate and cold source temperature. The comparison between modeling results and experimental data highlights a good numerical evaluation of temperatures. Furthermore, the model is able to represent a pretty good dynamic evolution of hydraulic variables.

  18. An automated two-phase system for hydrogel microbead production.

    Science.gov (United States)

    Coutinho, Daniela F; Ahari, Amir F; Kachouie, Nezamoddin N; Gomes, Manuela E; Neves, Nuno M; Reis, Rui L; Khademhosseini, Ali

    2012-09-01

    Polymeric beads have been used for protection and delivery of bioactive materials, such as drugs and cells, for different biomedical applications. Here, we present a generic two-phase system for the production of polymeric microbeads of gellan gum or alginate, based on a combination of in situ polymerization and phase separation. Polymer droplets, dispensed using a syringe pump, formed polymeric microbeads while passing through a hydrophobic phase. These were then crosslinked, and thus stabilized, in a hydrophilic phase as they crossed through the hydrophobic-hydrophilic interface. The system can be adapted to different applications by replacing the bioactive material and the hydrophobic and/or the hydrophilic phases. The size of the microbeads was dependent on the system parameters, such as needle size and solution flow rate. The size and morphology of the microbeads produced by the proposed system were uniform, when parameters were kept constant. This system was successfully used for generating polymeric microbeads with encapsulated fluorescent beads, cell suspensions and cell aggregates proving its ability for generating bioactive carriers that can potentially be used for drug delivery and cell therapy.

  19. What are the structural features that drive partitioning of proteins in aqueous two-phase systems?

    Science.gov (United States)

    Wu, Zhonghua; Hu, Gang; Wang, Kui; Zaslavsky, Boris Yu; Kurgan, Lukasz; Uversky, Vladimir N

    2017-01-01

    Protein partitioning in aqueous two-phase systems (ATPSs) represents a convenient, inexpensive, and easy to scale-up protein separation technique. Since partition behavior of a protein dramatically depends on an ATPS composition, it would be highly beneficial to have reliable means for (even qualitative) prediction of partitioning of a target protein under different conditions. Our aim was to understand which structural features of proteins contribute to partitioning of a query protein in a given ATPS. We undertook a systematic empirical analysis of relations between 57 numerical structural descriptors derived from the corresponding amino acid sequences and crystal structures of 10 well-characterized proteins and the partition behavior of these proteins in 29 different ATPSs. This analysis revealed that just a few structural characteristics of proteins can accurately determine behavior of these proteins in a given ATPS. However, partition behavior of proteins in different ATPSs relies on different structural features. In other words, we could not find a unique set of protein structural features derived from their crystal structures that could be used for the description of the protein partition behavior of all proteins in all ATPSs analyzed in this study. We likely need to gain better insight into relationships between protein-solvent interactions and protein structure peculiarities, in particular given limitations of the used here crystal structures, to be able to construct a model that accurately predicts protein partition behavior across all ATPSs. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. Ultrasound-Assisted Aqueous Two-Phase System for Extraction and Enrichment of Zanthoxylum armatum Lignans

    Directory of Open Access Journals (Sweden)

    Tao Guo

    2015-08-01

    Full Text Available In the study, an aqueous two phase system (ATPS coupled with ultrasound was employed to extract lignans from Zanthoxylum armatum. Three standard lignans, namely (−-fargesin, sesamin and L-asarinin, were used as marker compounds, and extraction was optimized and projected by response surface methodology (RSM and artificial neural network (ANN. The optimal condition for ATPS with 20% n-propanol and 24% (NH42SO4 coupled with ultrasonic-assisted extraction including a solvent to solid ratio of 15:1, a temperature of 40 °C, and a treatment time of 55 min was obtained. Under the condition, the yield of (−-fargesin increased 15.12%, and the purities of (−-fargesin, sesamin and L-asarinin reached 2.222%, 1.066%, and 1.583%, with an increase of 44.38%, 25.70%, and 26.34% compared to those extracted with 95% ethanol, respectively. Coefficient of the determined (0.9855 and mean squared error (0.0018 of ANN model suggested good fitness and generalization of the ANN. Taken together, the results showed that ultrasonic-assisted ATPS can be a suitable method for extraction and enrichment of lignans from Z. armatum.

  1. Effective extraction of elastase from Bacillus sp. fermentation broth using aqueous two-phase system

    Institute of Scientific and Technical Information of China (English)

    XU Ying; HE Guo-qing; LI Jing-jun

    2005-01-01

    This paper presents the evaluation of an aqueous two-phase system (ATPS) for extracting elastase produced by Bacillus sp. EL31410. The elastase and cell partition behavior in polyethylene glycol (PEG)/salt systems was investigated. The suitable system for elastase extraction was PEG/KH2PO4-K2HPO4, in which elastase is mainly partitioned into the PEG-rich phase,while the cells remained in the other phase. The influence of defined system parameters (e.g. PEG molecular mass, pH, NaCl addition) on the partitioning behavior of elastase is described. The concentration of phase forming components, PEG and KH2PO4-K2HPO4, was optimized for elastase recovery by means of response surface methodology, and it was found that they greatly influenced extraction recovery. The optimal ATPS was 23.1% (w/w) PEG 2 000 and 11.7% (w/w) KH2PO4-K2HPO4. The predicted recovery was about 89.5%, so this process is suggested to be a rapid and convenient method for elastase extraction.

  2. Effective extraction of elastase from Bacillus sp. fermentation broth using aqueous two-phase system.

    Science.gov (United States)

    Xu, Ying; He, Guo-qing; Li, Jing-jun

    2005-11-01

    This paper presents the evaluation of an aqueous two-phase system (ATPS) for extracting elastase produced by Bacillus sp. EL31410. The elastase and cell partition behavior in polyethylene glycol (PEG)/salt systems was investigated. The suitable system for elastase extraction was PEG/KH(2)PO(4)-K(2)HPO(4), in which elastase is mainly partitioned into the PEG-rich phase, while the cells remained in the other phase. The influence of defined system parameters (e.g. PEG molecular mass, pH, NaCl addition) on the partitioning behavior of elastase is described. The concentration of phase forming components, PEG and KH(2)PO(4)-K(2)HPO(4), was optimized for elastase recovery by means of response surface methodology, and it was found that they greatly influenced extraction recovery. The optimal ATPS was 23.1% (w/w) PEG 2 000 and 11.7% (w/w) KH(2)PO(4)-K(2)HPO(4). The predicted recovery was about 89.5%, so this process is suggested to be a rapid and convenient method for elastase extraction.

  3. The Effect of pH Difference Between Two Phases on the Partition of Lysozyme in Aqueous Two-Phase System

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    In the investigation of effect of KSCN on the partitioning of lysozyme in PEG2000/ammonium sulfate aqueous two-phase system, it was found that the KSCN could alter the pH difference between the two phases, and thus affect the partition of lysozyme. The relationship between partition coefficients of lysozyme and pH differences between two phases was discussed.

  4. A green deep eutectic solvent-based aqueous two-phase system for protein extracting

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Kaijia; Wang, Yuzhi, E-mail: wyzss@hnu.edu.cn; Huang, Yanhua; Li, Na; Wen, Qian

    2015-03-15

    Highlights: • A strategy for the protein purification with a deep eutectic solvent(DES)-based aqueous two-phase system. • Choline chloride-glycerin DES was selected as the extraction solvent. • Bovine serum albumin and trypsin were used as the analytes. • Aggregation phenomenon was detected in the mechanism research. - Abstract: As a new type of green solvent, deep eutectic solvent (DES) has been applied for the extraction of proteins with an aqueous two-phase system (ATPS) in this work. Four kinds of choline chloride (ChCl)-based DESs were synthesized to extract bovine serum albumin (BSA), and ChCl-glycerol was selected as the suitable extraction solvent. Single factor experiments have been done to investigate the effects of the extraction process, including the amount of DES, the concentration of salt, the mass of protein, the shaking time, the temperature and PH value. Experimental results show 98.16% of the BSA could be extracted into the DES-rich phase in a single-step extraction under the optimized conditions. A high extraction efficiency of 94.36% was achieved, while the conditions were applied to the extraction of trypsin (Try). Precision, repeatability and stability experiments were studied and the relative standard deviations (RSD) of the extraction efficiency were 0.4246% (n = 3), 1.6057% (n = 3) and 1.6132% (n = 3), respectively. Conformation of BSA was not changed during the extraction process according to the investigation of UV–vis spectra, FT-IR spectra and CD spectra of BSA. The conductivity, dynamic light scattering (DLS) and transmission electron microscopy (TEM) were used to explore the mechanism of the extraction. It turned out that the formation of DES–protein aggregates play a significant role in the separation process. All the results suggest that ChCl-based DES-ATPS are supposed to have the potential to provide new possibilities in the separation of proteins.

  5. Determination of partition coefficients of biomolecules in a microfluidic aqueous two phase system platform using fluorescence microscopy.

    Science.gov (United States)

    Silva, D F C; Azevedo, A M; Fernandes, P; Chu, V; Conde, J P; Aires-Barros, M R

    2017-03-03

    Aqueous two phase systems (ATPS) offer great potential for selective separation of a wide range of biomolecules by exploring differences in molecular solubility in each of the two immiscible phases. However, ATPS use has been limited due to the difficulty in predicting the behavior of a given biomolecule in the partition environment together with the empirical and time-consuming techniques that are used for the determination of partition and extraction parameters. In this work, a fast and novel technique based on a microfluidic platform and using fluorescence microscopy was developed to determine the partition coefficients of biomolecules in different ATPS. This method consists of using a microfluidic device with a single microchannel and three inlets. In two of the inlets, solutions containing the ATPS forming components were loaded while the third inlet was fed with the FITC tagged biomolecule of interest prepared in milli-Q water. Using fluorescence microscopy, it was possible to follow the location of the FITC-tagged biomolecule and, by simply varying the pumping rates of the solutions, to quickly test a wide variety of ATPS compositions. The ATPS system is allowed 4min for stabilization and fluorescence micrographs are used to determine the partition coefficient.The partition coefficients obtained were shown to be consistent with results from macroscale ATPS partition. This process allows for faster screening of partition coefficients using only a few microliters of material for each ATPS composition and is amenable to automation. The partitioning behavior of several biomolecules with molecular weights (MW) ranging from 5.8 to 150kDa, and isoelectric points (pI) ranging from 4.7 to 6.4 was investigated, as well as the effect of the molecular weight of the polymer ATPS component. Copyright © 2016 Elsevier B.V. All rights reserved.

  6. Study of organic compounds-water interactions by partition in aqueous two-phase systems.

    Science.gov (United States)

    Madeira, Pedro P; Bessa, Ana; Teixeira, Miguel A; Álvares-Ribeiro, Luís; Aires-Barros, M Raquel; Rodrigues, Alírio E; Zaslavsky, Boris Y

    2013-12-27

    Partition coefficients of fourteen organic compounds were determined in 10 or 20 different polymer/polymer aqueous two-phase systems (ATPS) all at physiological pH (0.15M NaCl in 0.01M phosphate buffer, pH 7.4). Solute-specific coefficients characterizing different types of solute-water interactions for the compounds examined were determined by the multiple linear regression analysis. It is shown that (i) the partition behavior for the polar organic compounds is affected not only by dipole-dipole and hydrogen-bond interactions with aqueous environment but, notably, in most cases also by dipole-ion interactions; (ii) it is possible to predict partition behavior for compounds with pre-determined solute-specific coefficients in ATPS with characterized solvent features; and (iii) linear combinations of the solute-specific coefficients for the organic compounds might be useful in the development of quantitative structure-activity relationship (QSAR) analysis to describe their odor detection threshold.

  7. Selective separation of protein and saccharides by ionic liquids aqueous two-phase systems

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    In the present work,it was found that aqueous solution of a hydrophilic ionic liquid (IL),1-butyl-3-methylimidazolium dicyanamide ([C4mim][N(CN)2]),could be separated into an aqueous two-phase system (ATPS) by inorganic salts such as K2HPO4 and K3PO4.The top phase is IL-rich,while the bottom phase is phosphate-rich.It was shown that 82.7%-100% bovine serum albumin (BSA) could be enriched into the top phase and almost quantitative saccharides (arabinose,glucose,sucrose,raffinose or dextran) were preferentially extracted into the bottom phase in a single-step extraction by [C4mim][N(CN)2] + K2HPO4 ATPS.The extraction efficiency of BSA from the aqueous saccharide solutions was influenced by the molecular structure of saccharides.The conductivity,dynamic light scattering (DLS) and transmission electron microscopy (TEM) were combined to investigate the microstructure of the IL-rich top phase and the possible mechanism for the selective separation.It is suggested that the formation of the IL aggregate and the IL aggregate-BSA complex plays a significant role in the separation of BSA from aqueous saccharide solutions.This is the first example for the selective separation by ILs-based ATPSs.It is expected that these findings would have potential applications in bio-analysis,separation,and IL recycle.

  8. Development of tropine-salt aqueous two-phase systems and removal of hydrophilic ionic liquids from aqueous solution.

    Science.gov (United States)

    Wu, Haoran; Yao, Shun; Qian, Guofei; Song, Hang

    2016-08-26

    A novel aqueous two-phase systems (ATPS) composed of a small molecule organic compound tropine and an organic or inorganic salt aqueous solution has been developed for the first time. The phase behavior of tropine-salt ATPS was systemically investigated and the phase equilibrium data were measured in different temperatures and concentrations and correlated by the Merchuk equation with satisfactory results. The detection of the conductivity and particle size proved the formation of micelle in the process of forming tropine-salt ATPS. The separation application of the ATPS was assessed with the removal of hydrophilic benzothiazolium-based ionic liquids (ILs) from aqueous solution. The result showed that ILs were effectively extracted into the top tropine-rich phase. Finally, ILs in the top tropine-rich phase were further separated by the means of adsorption-desorption with DM301 macroporous resin and ethanol. The method of novel tropine-salt ATPS combined with adsorption-desorption is demonstrated a promising alternative thought and approach for the removal or recovery of hydrophilic compounds from aqueous media and also could provide a potential application for bio-separation.

  9. Aqueous two-phase system based on natural quaternary ammonium compounds for the extraction of proteins.

    Science.gov (United States)

    Zeng, Chao-Xi; Xin, Rui-Pu; Qi, Sui-Jian; Yang, Bo; Wang, Yong-Hua

    2016-02-01

    Aqueous two-phase systems, based on the use of natural quaternary ammonium compounds, were developed to establish a benign biotechnological route for efficient protein separation. In this study, aqueous two-phase systems of two natural resources betaine and choline with polyethyleneglycol (PEG400/600) or inorganic salts (K2 HPO4 /K3 PO4 ) were formed. It was shown that in the K2 HPO4 -containing aqueous two-phase system, hydrophobic interactions were an important driving force of protein partitioning, while protein size played a vital role in aqueous two-phase systems that contained polyethylene glycol. An extraction efficiency of more than 90% for bovine serum albumin in the betaine/K2 HPO4 aqueous two-phase system can be obtained, and this betaine-based aqueous two-phase system provided a gentle and stable environment for the protein. In addition, after investigation of the cluster phenomenon in the betaine/K2 HPO4 aqueous two-phase systems, it was suggested that this phenomenon also played a significant role for protein extraction in this system. The development of aqueous two-phase systems based on natural quaternary ammonium compounds not only provided an effective and greener method of aqueous two-phase system to meet the requirements of green chemistry but also may help to solve the mystery of the compartmentalization of biomolecules in cells.

  10. Purification of C-phycocyanin from Spirulina platensis in aqueous two-phase systems using an experimental design

    Directory of Open Access Journals (Sweden)

    Francine Silva Antelo

    2015-02-01

    Full Text Available C-phycocyanin from Spirulina platensis was purified in aqueous two-phase systems (ATPS of polyethylene glycol (PEG/potassium phosphate, varying the molar mass of the PEG. Results using a full factorial design showed that an increase in the concentration of salt and decrease in the concentration of PEG caused an increment in the purification factor for all the ATPS studied. Optimization of the conditions of the purification was studied using a central composite rotatable design for each molar mass of PEG. The ATPS composed of 7% (w/w PEG 1500 or 4% (w/w PEG 8000 (g/gmol and 23 or 22.5% (w/w of phosphate resulted a purification factor of 1.6-fold for C-phycocyanin, with total and 57% recovery, respectively. Process conditions were optimized for the purification factor for the system with PEG 1500. The ATPS with 4% (w/w PEG 4000 or 4% (w/w PEG 6000 and 21% (w/w phosphate resulted purification factors of 2.1 and 2.2-fold, recovering 100% and 73.5%, respectively of C-phycocyanin in the top phase.

  11. Extraction and purification of wheat-esterase using aqueous two-phase systems of ionic liquid and salt.

    Science.gov (United States)

    Jiang, Bin; Feng, Zhibiao; Liu, Chunhong; Xu, Yingcao; Li, Dongmei; Ji, Guo

    2015-05-01

    To explore a new and simple rapid extraction and purification technique for wheat-esterase, an ionic liquids (ILs)-based aqueous two-phase system (ATPS) was developed for the purification of wheat-esterase from wheat extracts. Effects of various process parameters such as the concentrations of [Bmim]BF4, the types and concentrations of phase-forming salt, the system pH and the temperature on partitioning of wheat-esterase were evaluated. The obtained data indicated that wheat-esterase was preferentially partitioned into the ILs-rich phase and the ATPS composed of 20 % [Bmim]BF4 (w/w) and 25 % (w/w) NaH2PO4(pH = 4.8) showed good selectivity on wheat-esterase. Under the optimum conditions, wheat-esterase was purified with an acceptable yield (88.93 %), but produced wheat-esterase was 4.23 times as pure. It was obvious that temperature shows little influence on the purification between 10 and 50 °C. Sephadex G-150FF revealed that the band intensity of contaminating proteins in ATPS fraction almost disappeared. Therefore, ILs-based ATPS was an effective method for partitioning and recovery of wheat-esterase from wheat crude extracts.

  12. Heat transfer studies in a spiral plate heat exchanger for water: palm oil two phase system

    Directory of Open Access Journals (Sweden)

    S. Ramachandran

    2008-09-01

    Full Text Available Experimental studies were conducted in a spiral plate heat exchanger with hot water as the service fluid and the two-phase system of water – palm oil in different mass fractions and flow rates as the cold process fluid. The two phase heat transfer coefficients were correlated with Reynolds numbers (Re in the form h = a Re m, adopting an approach available in literature for two phase fluid flow. The heat transfer coefficients were also related to the mass fraction of palm oil for identical Reynolds numbers. The two-phase multiplier (ratio of the heat transfer coefficient of the two phase fluid and that of the single phase fluid was correlated with the Lockhart Martinelli parameter in a polynomial form. This enables prediction of the two-phase coefficients using single-phase data. The predicted coefficients showed a spread of ± 10 % in the laminar range.

  13. Purification and in situ immobilization of papain with aqueous two-phase system.

    Science.gov (United States)

    Li, Mingliang; Su, Erzheng; You, Pengyong; Gong, Xiangyu; Sun, Ming; Xu, Diansheng; Wei, Dongzhi

    2010-12-13

    Papain was purified from spray-dried Carica papaya latex using aqueous two-phase system (ATPS). Then it was recovered from PEG phase by in situ immobilization or preparing cross-linked enzyme aggregates (CLEAs). The Plackett-Burman design and the central composite design (CCD) together with the response surface methodology (RSM) were used to optimize the APTS processes. The highly purified papain (96-100%) was achieved under the optimized conditions: 40% (w/w) 15 mg/ml enzyme solution, 14.33-17.65% (w/w) PEG 6000, 14.27-14.42% (w/w) NaH2PO4/K2HPO4 and pH 5.77-6.30 at 20°C. An in situ enzyme immobilization approach, carried out by directly dispersing aminated supports and chitosan beads into the PEG phase, was investigated to recover papain, in which a high immobilization yield (>90%) and activity recovery (>40%) was obtained. Moreover, CLEAs were successfully used in recovering papain from PEG phase with a hydrolytic activity hundreds times higher than the carrier-bound immobilized papain.

  14. A two-phase system call arguments attribute analyzing method

    Institute of Scientific and Technical Information of China (English)

    LI Hong-jiao; LI Jian-hua

    2008-01-01

    To detect more attacks aiming at key security data in program behavior-based anomaly detection, the data flow properties were formulated as unary and binary relations on system call arguments. A new method named two-phrase analysis (2PA) is designed to analyze the efficient relation dependency, and its description as well as advantages are discussed. During the phase of static analysis, a dependency graph was constructed according to the program's data dependency graph, which was used in the phase of dynamic learning to learn specified binary relations. The constructed dependency graph only stores the information of related arguments and events, thus improves the efficiency of the learning algorithm and reduces the size of learned relation de-pendencies. Performance evaluations show that the new method is more efficient than existing methods.

  15. Formation and characteristics of aqueous two-phase systems formed by a cationic surfactant and a series of ionic liquids.

    Science.gov (United States)

    Wei, Xi-Lian; Wang, Xiu-Hong; Ping, A-Li; Du, Pan-Pan; Sun, De-Zhi; Zhang, Qing-Fu; Liu, Jie

    2013-11-15

    Aqueous two-phase systems (ATPS) were obtained in the aqueous mixtures of a cationic surfactant and a series of ionic liquids (ILs). The effects of IL structure, temperature and additives on the phase separation were systematically investigated. The microstructures of some ATPS were observed by freeze-fracture replication technique. Lyotropic liquid crystal was found in the bottom phase besides micelles under different conditions. Remarkably, both IL structure and additives profoundly affected the formation and properties of the ATPSs. The phase separation can be attributed to the existence of different aggregates and the cation-π interactions of the cationic surfactant with the ILs, which has a significant role in the formation of ATPS. The extraction capacity of the studied ATPS was also evaluated through their application in the extraction of two biosubstances. The results indicate that the ILs with BF4(-) as anion show much better extraction efficiencies than the corresponding ILs with Br(-) as anion do under the same conditions. l-Tryptophan was mainly distributed into the NPTAB-rich phase, while methylene blue and capsochrome were mainly in the IL-rich phase.

  16. Symmetrical components and power analysis for a two-phase microgrid system

    DEFF Research Database (Denmark)

    Alibeik, M.; Santos Jr., E. C. dos; Blaabjerg, Frede

    2014-01-01

    This paper presents a mathematical model for the symmetrical components and power analysis of a new microgrid system consisting of three wires and two voltages in quadrature, which is designated as a two-phase microgrid. The two-phase microgrid presents the following advantages: 1) constant power...

  17. Two-phase aqueous micellar systems: an alternative method for protein purification

    Directory of Open Access Journals (Sweden)

    Rangel-Yagui C. O.

    2004-01-01

    Full Text Available Two-phase aqueous micellar systems can be exploited in separation science for the extraction/purification of desired biomolecules. This article reviews recent experimental and theoretical work by Blankschtein and co-workers on the use of two-phase aqueous micellar systems for the separation of hydrophilic proteins. The experimental partitioning behavior of the enzyme glucose-6-phosphate dehydrogenase (G6PD in two-phase aqueous micellar systems is also reviewed and new results are presented. Specifically, we discuss very recent work on the purification of G6PD using: i a two-phase aqueous micellar system composed of the nonionic surfactant n-decyl tetra(ethylene oxide (C10E4, and (ii a two-phase aqueous mixed micellar system composed of C10E4 and the cationic surfactant decyltrimethylammonium bromide (C10TAB. Our results indicate that the two-phase aqueous mixed (C10E4/C10TAB micellar system can improve significantly the partitioning behavior of G6PD relative to that observed in the two-phase aqueous C10E4 micellar system.

  18. A resolution approach of racemic phenylalanine with aqueous two-phase systems of chiral tropine ionic liquids.

    Science.gov (United States)

    Wu, Haoran; Yao, Shun; Qian, Guofei; Yao, Tian; Song, Hang

    2015-10-30

    Aqueous two-phase systems (ATPS) based on tropine type chiral ionic liquids and inorganic salt solution were designed and prepared for the enantiomeric separation of racemic phenylalanine. The phase behavior of IL-based ATPS was comprehensive investigated, and phase equilibrium data were correlated by Merchuk equation. Various factors were also systematically investigated for their influence on separation efficiency. Under the appropriate conditions (0.13g/g [C8Tropine]pro, 35mg/g Cu(Ac)2, 20mg/g d,l-phenylalanine, 0.51g/g H2O and 0.30g/g K2HPO4), the enantiomeric excess value of phenylalanine in solid phase (mainly containing l-enantiomer) was 65%. Finally, the interaction mechanism was studied via 1D and 2D NMR. The results indicate that d-enantiomer of phenylalanine interacts more strongly with chiral ILs and Cu(2+) based on the chiral ion-pairs space coordination mechanism, which makes it tend to remain in the top IL-rich phase. By contrast, l-enantiomer is transferred into the solid phase. Above chiral ionic liquids aqueous two-phase systems have demonstrated obvious resolution to racemic phenylalanine and could be promising alterative resolution approach for racemic amino acids in aqueous circumstance.

  19. Extraction and purification of anthraquinones derivatives from Aloe vera L. using alcohol/salt aqueous two-phase system.

    Science.gov (United States)

    Tan, Zhi-jian; Li, Fen-fang; Xu, Xue-lei

    2013-08-01

    An alcohol/salt aqueous two-phase system (ATPS) composed of 1-propanol and (NH4)2SO4 was employed to purify anthraquinones (AQs) extracted from Aloe vera L. The main influencing system parameters such as type of alcohol, type and concentration of salt, temperature and pH were investigated in detail. Under the optimal extraction conditions, AQs can be extracted into alcohol-rich phase with high extraction efficiency, meanwhile majority polysaccharides, proteins, mineral substances and other impurities were extracted into salt-rich phase. Partitioning of AQs is dependent on hydrophobic interaction, hydrogen bond interaction, and salting-out effect in ATPS. Temperature also played a great role in the partitioning. After ATPS extraction, alcohol can be recycled by evaporation; moreover, salt can be recycled by dilution crystallization method. Compared with other liquid-liquid extractions, this alcohol/salt system is much simpler, lower in cost with easier recovery of phase-forming components, which has the potential scale-up in down-processing of active ingredients in plant.

  20. Bioconversion of apigenin-7-O-β-glucoside in aqueous two-phase system

    OpenAIRE

    Ilić Sanja M.; Đaković Sanja D.; Cvejić Jelena H.; Antov Mirjana G.; Zeković Zoran P.

    2005-01-01

    The study is concerned with the conversion of apigenin-7-O-β-glucoside into apigenin in polyethylene glycol 6000 / dextran 20000 aqueous two-phase system by β-glucosidase. Apigenin was separated from apigenin-7-O-β-glucoside and β-glucosidase by their partition into opposite phases. In 14% PEG / 22.5% DEX aqueous two-phase system obtained yield of apigenin in top phase was 108%.

  1. Bioconversion of apigenin-7-O-β-glucoside in aqueous two-phase system

    Directory of Open Access Journals (Sweden)

    Ilić Sanja M.

    2005-01-01

    Full Text Available The study is concerned with the conversion of apigenin-7-O-β-glucoside into apigenin in polyethylene glycol 6000 / dextran 20000 aqueous two-phase system by β-glucosidase. Apigenin was separated from apigenin-7-O-β-glucoside and β-glucosidase by their partition into opposite phases. In 14% PEG / 22.5% DEX aqueous two-phase system obtained yield of apigenin in top phase was 108%.

  2. Living between two worlds: two-phase culture systems for producing plant secondary metabolites.

    Science.gov (United States)

    Malik, Sonia; Hossein Mirjalili, Mohammad; Fett-Neto, Arthur Germano; Mazzafera, Paulo; Bonfill, Mercedes

    2013-03-01

    The two-phase culture system is an important in vitro strategy to increase the production of secondary metabolites (SMs) by providing an enhanced release of these compounds from plant cells. Whereas the first phase supports cell growth, the second phase provides an additional site or acts as a metabolic sink for the accumulation of SMs and also reduces feedback inhibition. This review is focused on several aspects of the two-phase culture system and aims to show the diverse possibilities of employing this technique for the in vitro production of SMs from plant cells. Depending on the material used in the secondary phase, two-phase culture systems can be broadly categorised as liquid-liquid or liquid-solid. The choice of material for the second phase depends on the type of compound to be recovered and the compatibility with the other phase. Different factors affecting the efficiency of two-phase culture systems include the choice of material for the secondary phase, its concentration, volume, and time of addition. Factors such as cell elicitation, immobilization, and permeabilization, have been suggested as important strategies to make the two-phase culture system practically reliable on a commercial scale. Since there are many possibilities for designing a two-phase system, more detailed studies are needed to broaden the range of secondary phases compatible with the various plant species producing SMs with potential applications, mainly in the food and pharmacology industries.

  3. Characterization of aqueous two phase systems by combining lab-on-a-chip technology with robotic liquid handling stations.

    Science.gov (United States)

    Amrhein, Sven; Schwab, Marie-Luise; Hoffmann, Marc; Hubbuch, Jürgen

    2014-11-07

    Over the last decade, the use of design of experiment approaches in combination with fully automated high throughput (HTP) compatible screenings supported by robotic liquid handling stations (LHS), adequate fast analytics and data processing has been developed in the biopharmaceutical industry into a strategy of high throughput process development (HTPD) resulting in lower experimental effort, sample reduction and an overall higher degree of process optimization. Apart from HTP technologies, lab-on-a-chip technology has experienced an enormous growth in the last years and allows further reduction of sample consumption. A combination of LHS and lab-on-a-chip technology is highly desirable and realized in the present work to characterize aqueous two phase systems with respect to tie lines. In particular, a new high throughput compatible approach for the characterization of aqueous two phase systems regarding tie lines by exploiting differences in phase densities is presented. Densities were measured by a standalone micro fluidic liquid density sensor, which was integrated into a liquid handling station by means of a developed generic Tip2World interface. This combination of liquid handling stations and lab-on-a-chip technology enables fast, fully automated, and highly accurate density measurements. The presented approach was used to determine the phase diagram of ATPSs composed of potassium phosphate (pH 7) and polyethylene glycol (PEG) with a molecular weight of 300, 400, 600 and 1000 Da respectively in the presence and in the absence of 3% (w/w) sodium chloride. Considering the whole ATPS characterization process, two complete ATPSs could be characterized within 24h, including four runs per ATPS for binodal curve determination (less than 45 min/run), and tie line determination (less than 45 min/run for ATPS preparation and 8h for density determination), which can be performed fully automated over night without requiring man power. The presented methodology provides

  4. pH recycling aqueous two-phase systems applied in extraction of Maitake β-Glucan and mechanism analysis using low-field nuclear magnetic resonance.

    Science.gov (United States)

    Hou, Huiyun; Cao, Xuejun

    2015-07-31

    In this paper, a recycling aqueous two-phase systems (ATPS) based on two pH-response copolymers PADB and PMDM were used in purification of β-Glucan from Grifola frondosa. The main parameters, such as polymer concentration, type and concentration of salt, extraction temperature and pH, were investigated to optimize partition conditions. The results demonstrated that β-Glucan was extracted into PADB-rich phase, while impurities were extracted into PMDM-rich phase. In this 2.5% PADB/2.5% PMDM ATPS, 7.489 partition coefficient and 96.92% extraction recovery for β-Glucan were obtained in the presence of 30mmol/L KBr, at pH 8.20, 30°C. The phase-forming copolymers could be recycled by adjusting pH, with recoveries of over 96.0%. Furthermore, the partition mechanism of Maitake β-Glucan in PADB/PMDM aqueous two-phase systems was studied. Fourier transform infrared spectra, ForteBio Octet system and low-field nuclear magnetic resonance (LF-NMR) were introduced for elucidating the partition mechanism of β-Glucan. Especially, LF-NMR was firstly used in the mechanism analysis in partition of aqueous two-phase systems. The change of transverse relaxation time (T2) in ATPS could reflect the interaction between polymers and β-Glucan.

  5. Camomile autofermentation in polyethylene glycol/dextran two-phase system

    Directory of Open Access Journals (Sweden)

    Đaković Sanja D.

    2008-01-01

    Full Text Available The objective of this study was the investigation of the extractive bioconversion of apigenin-7-O-β-glucoside in camomile ligulate flowers into apigenin by autofermentation in polyethylene glycol 6000/dextran 200000 two-phase system. In 22.5% polyethylene glycol/14% dextran aqueous two-phase system the obtained yield of apigenin in the top phase was 96.5%. In the presence of plant material that partiotioned to the interphase, the yield of apigenin in the top phase was 3.5 times higher in comparison to the model system.

  6. Isolation of natural red colorants from fermented broth using ionic liquid-based aqueous two-phase systems.

    Science.gov (United States)

    Ventura, Sónia P M; Santos-Ebinuma, Valéria C; Pereira, Jorge F B; Teixeira, Maria F S; Pessoa, Adalberto; Coutinho, João A P

    2013-05-01

    There is a growing demand for natural colorants. This is prompting the search for new alternative and "benign" separation systems allowing higher recoveries, extraction yields, and selectivities. This work investigates the use of aqueous two-phase systems (ATPS) based on ionic liquids as extraction processes for the recovery of red colorants from the fermented broth of Penicillium purpurogenum DPUA 1275. Several ATPS based on quaternary ammonium and imidazolium were studied in this work aiming at separating the red colorants produced from the remaining colorants and contaminant proteins present in the fermented broth. The results suggest that the red colorants can be isolated by an appropriate manipulation of some of the process conditions, such as the use of quaternary ammonium with short alkyl chains, alkaline media, and short tie-line lengths (extraction point systems with lower concentrations of ionic liquid). These conditions allow large partition coefficients for the red colorants (K red = 24.4 ± 2.3), high protein removal (60.7 ± 2.8 %) and selectivity parameters (S red/prot = 10.05).

  7. Liquid-liquid extraction of enzymes by affinity aqueous two-phase systems

    Directory of Open Access Journals (Sweden)

    Xu Yan

    2003-12-01

    Full Text Available From analytical to commercial scale, aqueous two-phase systems have their application in the purification, characterization and study of biomaterials. In order to improve the selectivity of the systems, the biospecific affinity ligands were introduced. In the affinity partitioning aqueous two-phase system, have many enzymes been purified. This review discusses the partitioning of some enzymes in the affinity aqueous two-phase systems in regard to the different ligands, including reactive dyes, metal ions and other ligands. Some integration of aqueous two-phase system with other techniques for more effective purification of enzymes are also presented.Tanto em escala de laboratório como industrial, os sistemas de duas fases aquosas podem ser utilizados para a purificação, caracterização e estudos de biomateriais. Para aumentar a seletividade desse sistema, ligantes de afinidade bioespecíficos podem ser utilizados. No sistema de duas fases aquosas por afinidade, muitas enzimas podem ser purificadas. Neste artigo de revisão, a partição de algumas enzimas por esse tipo de afinidade, utilizando diferentes ligantes como corantes e íons metálicos, são discutidas. Além disso, a integração desse sistema de duas fases aquosas com outras técnicas de purificação estão sendo apresentados, com o objetivo mostrar a melhoria da eficiência do processo.

  8. Two-phase flow stability structure in a natural circulation system

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Zhiwei [Nuclear Engineering Laboratory Zurich (Switzerland)

    1995-09-01

    The present study reports a numerical analysis of two-phase flow stability structures in a natural circulation system with two parallel, heated channels. The numerical model is derived, based on the Galerkin moving nodal method. This analysis is related to some design options applicable to integral heating reactors with a slightly-boiling operation mode, and is also of general interest to similar facilities. The options include: (1) Symmetric heating and throttling; (2) Asymmetric heating and symmetric throttling; (3) Asymmetric heating and throttling. The oscillation modes for these variants are discussed. Comparisons with the data from the INET two-phase flow stability experiment have qualitatively validated the present analysis.

  9. Extraction of peptide tagged cutinase in detergent-based aqueous two-phase systems

    NARCIS (Netherlands)

    Rodenbrock, A.; Selber, K.; Egmond, M.R.; Kula, M.-R.

    2010-01-01

    Detergent-based aqueous two-phase systems have the advantage to require only one auxiliary chemical to induce phase separation above the cloud point. In a systematic study the efficiency of tryptophan-rich peptide tags was investigated to enhance the partitioning of an enzyme to the detergent-rich p

  10. Design, Modelling and Simulation of Two-Phase Two-Stage Electronic System with Orthogonal Output for Supplying of Two-Phase ASM

    Directory of Open Access Journals (Sweden)

    Michal Prazenica

    2011-01-01

    Full Text Available This paper deals with the two-stage two-phase electronic systems with orthogonal output voltages and currents - DC/AC/AC. Design of two-stage DC/AC/AC high frequency converter with two-phase orthogonal output using single-phase matrix converter is also introduced. Output voltages of them are strongly nonharmonic ones, so they must be pulse-modulated due to requested nearly sinusoidal currents with low total harmonic distortion. Simulation experiment results of matrix converter for both steady and transient states for IM motors are given in the paper, also experimental verification under R-L load, so far. The simulation results confirm a very good time-waveform of the phase current and the system seems to be suitable for low-cost application in automotive/aerospace industries and application with high frequency voltage sources.

  11. Separation of active laccases from Pleurotus sapidus culture supernatant using aqueous two-phase systems in centrifugal partition chromatography.

    Science.gov (United States)

    Schwienheer, C; Prinz, A; Zeiner, T; Merz, J

    2015-10-01

    For the production of bio active compounds, e.g., active enzymes or antibodies, a conserved purification process with a minimum loss of active compounds is necessary. In centrifugal partition chromatography (CPC), the separation effect is based on the different distribution of the components to be separated between two immiscible liquid phases. Thereby, one liquid phase is kept stationary in chambers by a centrifugal field and the mobile phase is pumped through via connecting ducts. Aqueous two phase systems (ATPS) are known to provide benign conditions for biochemical products and seem to be promising when used in CPC for purification tasks. However, it is not known if active biochemical compounds can "survive" the conditions in a CPC where strong shear forces can occur due to the two-phasic flow under centrifugal forces. Therefore, this aspect has been faced within this study by the separation of active laccases from a fermentation broth of Pleurotus sapidus. After selecting a suitable ATPS and operating conditions, the activity yield was calculated and the preservation of the active enzymes could be observed. Therefore, CPC could be shown as potentially suitable for the purification of bio-active compounds.

  12. Development of green betaine-based deep eutectic solvent aqueous two-phase system for the extraction of protein.

    Science.gov (United States)

    Li, Na; Wang, Yuzhi; Xu, Kaijia; Huang, Yanhua; Wen, Qian; Ding, Xueqin

    2016-05-15

    Six kinds of new type of green betaine-based deep eutectic solvents (DESs) have been synthesized. Deep eutectic solvent aqueous two-phase systems (DES-ATPS) were established and successfully applied in the extraction of protein. Betaine-urea (Be-U) was selected as the suitable extractant. Single factor experiments were carried out to determine the optimum conditions of the extraction process, such as the salt concentration, the mass of DES, the separation time, the amount of protein, the temperature and the pH value. The extraction efficiency could achieve to 99.82% under the optimum conditions. Mixed sample and practical sample analysis were discussed. The back extraction experiment was implemented and the back extraction efficiency could reach to 32.66%. The precision experiment, repeatability experiment and stability experiment were investigated. UV-vis, FT-IR and circular dichroism (CD) spectra confirmed that the conformation of protein was not changed during the process of extraction. The mechanisms of extraction were researched by dynamic light scattering (DLS), the measurement of the conductivity and transmission electron microscopy (TEM). DES-protein aggregates and embraces phenomenon play considerable roles in the separation process. All of these results indicated that betaine-based DES-ATPS may provide a potential substitute new method for the separation of proteins.

  13. Partition separation and characterization of the polyhydroxyalkanoates synthase produced from recombinant Escherichia coli using an aqueous two-phase system.

    Science.gov (United States)

    Lan, John Chi-Wei; Yeh, Chun-Yi; Wang, Chih-Chi; Yang, Yu-Hsuan; Wu, Ho-Shing

    2013-10-01

    Polyhydroxyalkanoates (PHAs) are renewable and biodegradable polyesters which can be synthesized either by numerous of microorganisms in vivo or synthase in vitro. The synthesis of PHAs in vitro requires an efficient separation for high yield of purified enzyme. The recombinant Escherichia coli harboring phaC gene derived from Ralstonia eutropha H16 was cultivated in the chemically defined medium for overexpression of synthase in the present work. The purification and characteristics of PHA synthase from clarified feedstock by using aqueous two-phase systems (ATPS) was investigated. The optimized concentration of ATPS for partitioning PHA synthase contained polyethylene glycol 6000 (30%, w/w) and potassium phosphate (8%, w/w) with 3.25 volume ratio in the absence of NaCl at pH 8.7 and 4°C. The results showed that the partition coefficient of enzyme activity and protein content are 6.07 and 0.22, respectively. The specific activity, selectivity, purification fold and recovery of phaC(Re) achieved 1.76 U mg⁻¹, 29.05, 16.23 and 95.32%, respectively. Several metal ions demonstrated a significant effect on activity of purified enzyme. The purified enzyme displayed maximum relative activity as operating condition at pH value of 7.5 and 37°C. As compared to conventional purification processes, ATPS can be a promising technique applied for rapid recovery of PHA synthase and preparation of large quantity of PHA synthase on synthesis of P(3HB) in vitro.

  14. A microdevice assisted approach for the preparation, characterization and selection of continuous aqueous two-phase systems: from micro to bench-scale.

    Science.gov (United States)

    Vázquez-Villegas, Patricia; Ouellet, Eric; González, Claudia; Ruiz-Ruiz, Federico; Rito-Palomares, Marco; Haynes, Charles A; Aguilar, Oscar

    2016-07-05

    Aqueous two-phase systems (ATPS) have emerged as an alternative strategy for the recovery and purification of a wide variety of biological products. Typical process development requires a large screening of experimental conditions towards industrial adoption where continuous processes are preferred. In this work, it was proved that under certain flow conditions, ATPS could be formed continuously inside a microchannel, starting from stocks of phase components. Staggered herringbone chaotic micromixers included within the device sequentially and rapidly prepare two-phase systems across an entire range of useful phase compositions. Two-phase diagrams (binodal curves) were easily plotted using the cloud-point method for systems of different components and compared with previously reported curves for each system, proving that phase formation inside the device correlated with the previously reported diagrams. A proof of concept for sample partitioning in such a microdevice was performed with two different experimental models: BSA and red blood cells. Finally, the microdevice was employed to obtain information about the recovery and partition coefficient of invertase from a real complex mixture of proteins (yeast extract) to design a process for the recovery of the enzyme selecting a suitable system and composition to perform the process at bench-scale.

  15. Transport, geometrical, and topological properties of stealthy disordered hyperuniform two-phase systems.

    Science.gov (United States)

    Zhang, G; Stillinger, F H; Torquato, S

    2016-12-28

    Disordered hyperuniform many-particle systems have attracted considerable recent attention, since they behave like crystals in the manner in which they suppress large-scale density fluctuations, and yet also resemble statistically isotropic liquids and glasses with no Bragg peaks. One important class of such systems is the classical ground states of "stealthy potentials." The degree of order of such ground states depends on a tuning parameter χ. Previous studies have shown that these ground-state point configurations can be counterintuitively disordered, infinitely degenerate, and endowed with novel physical properties (e.g., negative thermal expansion behavior). In this paper, we focus on the disordered regime (0 two-phase media by circumscribing each point with a possibly overlapping sphere of a common radius a: the "particle" and "void" phases are taken to be the space interior and exterior to the spheres, respectively. The hyperuniformity of such two-phase media depends on the sphere sizes: While it was previously analytically proven that the resulting two-phase media maintain hyperuniformity if spheres do not overlap, here we show numerically that they lose hyperuniformity whenever the spheres overlap. We study certain transport properties of these systems, including the effective diffusion coefficient of point particles diffusing in the void phase as well as static and time-dependent characteristics associated with diffusion-controlled reactions. Besides these effective transport properties, we also investigate several related structural properties, including pore-size functions, quantizer error, an order metric, and percolation thresholds. We show that these transport, geometrical, and topological properties of our two-phase media derived from decorated stealthy ground states are distinctly different from those of equilibrium hard-sphere systems and spatially uncorrelated overlapping spheres. As the extent of short-range order increases, stealthy disordered

  16. Dynamic characteristics of two-phase thermal control system for spacecraft

    Science.gov (United States)

    Malozemov, Vladimir V.; Kudryavtseva, Natal'ya S.; Antonov, Viktor A.; Zagar, Oleg V.; Chernobaev, Nikolaj N.

    1992-07-01

    This paper deals with review of the issues associated with modelling the dynamic processes in the spacecraft two-phase thermal control systems. The work presents the results of modelling the nonstationary conditions of the evaporative and condensation heat exchangers functioning, investigates their response to the characteristic external influences. Disclosed are the results of the computer-aided modelling the two-phase thermal control system with a pump. The dynamic characteristics of the change in the inputs of pressures, temperatures and vapor content of a coolant in various branches of the system, as well as the lengths of the heat transfer zones in the evaporator and condenser under effect of the typical disturbing actions are obtained. The attained transients are analyzed.

  17. Synthesis of thermo-responsive polymers recycling aqueous two-phase systems and phase formation mechanism with partition of ε-polylysine.

    Science.gov (United States)

    Xu, Chengning; Dong, Wenying; Wan, Junfen; Cao, Xuejun

    2016-11-11

    Aqueous two-phase systems (ATPS) have the potential application in bioseparation and biocatalysis engineering. In this paper, a recyclable ATPS was developed by two thermo-responsive copolymers, PVBAm and PN. Copolymer PVBAm was copolymerized using N-vinylcaprolactam, Butyl methacrylate and Acrylamide as monomers, and PN was synthesized by N-isopropylacrylamide. The lower critical solution temperature (LCST) of PVBAm and PN were 45.0°C and 33.5°C, respectively. The recoveries of both polymers could achieve over 95.0%. The phase behavior and formation mechanism of PVBAm/PN ATPS was studied. Low-field nuclear magnetic resonance (LF-NMR) was applied in the phase-forming mechanism study in ATPS. In addition, combining the analysis results of surface tension, transmission electron microscopy and dynamic light scattering, the phase-forming of the PVBAm/PN ATPS was proved. The application was performed by partition of ε-polylysine in the 2% PVBAm/2% PN (w/w) ATPS. The results demonstrated that ε-polylysine was extracted into the PN-rich phase, the maximal partition coefficient (1/K) and extraction recovery of pure ε-polylysine were 6.87 and 96.36%, respectively, and 7.41 partition coefficient and 97.85% extraction recovery for ε-polylysine fermentation broth were obtained in the presence of 50mM (NH4)2SO4 at room temperature. And this method can effectively remove the most impurities from fermentation broth when (NH4)2SO4 exists in the ATPS. It is believed that the thermo-responsive recycling ATPS has a good application prospect in the field of bio-separation.

  18. Aqueous Two-Phase Systems formed by Biocompatible and Biodegradable Polysaccharides and Acetonitrile.

    Science.gov (United States)

    de Brito Cardoso, Gustavo; Souza, Isabela Nascimento; Pereira, Matheus M; Freire, Mara G; Soares, Cleide Mara Faria; Lima, Álvaro Silva

    2014-11-05

    In this work, it is shown that novel aqueous two-phase systems can be formed by the combination of acetonitrile and polysaccharides, namely dextran. Several ternary phase diagrams were determined at 25 °C for the systems composed of water + acetonitrile + dextran. The effect of the dextran molecular weight (6,000, 40,000 and 100,000 g.mol(-1)) was ascertained toward their ability to undergo liquid-liquid demixing. An increase in the dextran molecular weight favors the phase separation. Furthermore, the effect of temperature (25, 35 and 45 °C) was evaluated for the system constituted by the dextran of higher molecular weight. Lower temperatures are favorable for phase separation since lower amounts of dextran and acetonitrile are required for the creation of aqueous two-phase systems. In general, acetonitrile is enriched in the top phase while dextran is majorly concentrated in the bottom phase. The applicability of this new type of two-phase systems as liquid-liquid extraction approaches was also evaluated by the study of the partition behavior of a well-known antioxidant - vanillin - and used here as a model biomolecule. The optimized conditions led to an extraction efficiency of vanillin of 95% at the acetonitrile-rich phase.

  19. Drop volumes and terminal velocities in aqueous two-phase systems

    Energy Technology Data Exchange (ETDEWEB)

    Bhavasar, P. M.; Jafarabad, K. R.; Pandit, A. B.; Sawant, S. B.; Joshi, J. B. [Bombay Univ. (India). Dept. of Chemical Technology

    1996-12-01

    Two phase aqueous extraction techniques employed in liquid-liquid extraction equipment such as spray columns and plate columns were studied, with particular attention to predicting drop sizes prior to jetting, and their terminal velocity. In the particular system studied, the values obtained by conventional models as found in the literature were considered inapplicable. A generalised model was constructed using video photographic measurements, and a correlation was developed for the terminal velocities of the drops in aqueous two-phase systems. This simplified model was found to be successful in expressing the terminal rise/fall velocities of droplets covering a specific range of Morton numbers (representing physical properties) from 0.00211 to 11050 and Eotvos numbers (representative of drop size) from 0.091 to 288. 22 refs., 6 figs.

  20. Use of two-phase flow heat transfer method in spacecraft thermal system

    Science.gov (United States)

    Hye, A.

    1985-01-01

    In space applications, weight, volume and power are critical parameters. Presently liquid freon is used in the radiator planels of the Space Shuttle to dissipate heat. This requires a large amount of freon, large power for pumps, large volume and weight. Use of two-phase flow method to transfer heat can reduce them significantly. A modified commercial vapor compression refrigerator/freezer was sucessfully flown in STS-4 to study the effect of zero-gravity on the system. The duty cycle was about 5 percent higher in flight as compared to that on earth due to low flow velocity in condenser. The vapor Reynolds number at exit was about 4000 as compared to about 12,000. Efforts are underway to design a refrigerator/freezer using an oil-free compressor for Spacelab Mission 4 scheduled to fly in January 1986. A thermal system can be designed for spacecraft using the two-phase flow to transfer heat economically.

  1. Two-phase distribution in the vertical flow line of a domestic wet central heating system

    Directory of Open Access Journals (Sweden)

    Ge Y.T.

    2013-04-01

    Full Text Available The theoretical and experimental aspects of bubble distribution in bubbly two-phase flow are reviewed in the context of the micro bubbles present in a domestic gas fired wet central heating system. The latter systems are mostly operated through the circulation of heated standard tap water through a closed loop circuit which often results in water supersaturated with dissolved air. This leads to micro bubble nucleation at the primary heat exchanger wall, followed by detachment along the flow. Consequently, a bubbly two-phase flow characterises the flow line of such systems. The two-phase distribution across the vertical and horizontal pipes was measured through a consideration of the volumetric void fraction, quantified through photographic techniques. The bubble distribution in the vertical pipe in down flow conditions was measured to be quasi homogenous across the pipe section with a negligible reduction in the void fraction at close proximity to the pipe wall. Such a reduction was more evident at lower bulk fluid velocities.

  2. Two-phase distribution in the vertical flow line of a domestic wet central heating system

    Science.gov (United States)

    Fsadni, A.-M.; Ge, Y. T.

    2013-04-01

    The theoretical and experimental aspects of bubble distribution in bubbly two-phase flow are reviewed in the context of the micro bubbles present in a domestic gas fired wet central heating system. The latter systems are mostly operated through the circulation of heated standard tap water through a closed loop circuit which often results in water supersaturated with dissolved air. This leads to micro bubble nucleation at the primary heat exchanger wall, followed by detachment along the flow. Consequently, a bubbly two-phase flow characterises the flow line of such systems. The two-phase distribution across the vertical and horizontal pipes was measured through a consideration of the volumetric void fraction, quantified through photographic techniques. The bubble distribution in the vertical pipe in down flow conditions was measured to be quasi homogenous across the pipe section with a negligible reduction in the void fraction at close proximity to the pipe wall. Such a reduction was more evident at lower bulk fluid velocities.

  3. Simulation of non-equilibrium two-phase flow in single component fluid systems

    Energy Technology Data Exchange (ETDEWEB)

    Hoyer, Norbert [Scandpower A/S, Kjeller (Norway)

    1996-12-31

    Traditionally, two-phase flow has been modelled by separate correlations for void fraction, pressure drop and flow regimes. A more unified approach, which treats flow regimes as an integral part of the two-fluid model is described in this work. A general, transient simulator for steam-water/inert gas systems has been developed. MONA is based on a full two-fluid, three field, nonequilibrium, nonhomogeneous two-phase flow model. It includes further an extensive heat and mass transfer package. The major contribution for MONA validation comes from the FRIGG loop experiments, covering a wide range of parameters like geometry, flow, subcooling, pressure and heat flux. Both validation against steady state and dynamic experiments has been carried out, the former comprising void fractions, pressure drops as well as natural and forced circulation flow rates while the latter consists of boiling instability analysis. 69 refs., 41 figs., 5 tabs.

  4. Preparative crystallization of a single chain antibody using an aqueous two-phase system.

    Science.gov (United States)

    Huettmann, Hauke; Berkemeyer, Matthias; Buchinger, Wolfgang; Jungbauer, Alois

    2014-11-01

    A simultaneous crystallization and aqueous two-phase extraction of a single chain antibody was developed, demonstrating process integration. The process conditions were designed to form an aqueous two-phase system, and to favor crystallization, using sodium sulfate and PEG-2000. At sufficiently high concentrations of PEG, a second phase was generated in which the protein crystallization occurred simultaneously. The single chain antibody crystals were partitioned to the top, polyethylene glycol-rich phase. The crystal nucleation took place in the sodium sulfate-rich phase and at the phase boundary, whereas crystal growth was progressing mainly in the polyethylene glycol-rich phase. The crystals in the polyethylene glycol-rich phase grew to a size of >50 µm. Additionally, polyethylene glycol acted as an anti-solvent, thus, it influenced the crystallization yield. A phase diagram with an undersaturation zone, crystallization area, and amorphous precipitation zone was established. Only small differences in polyethylene glycol concentration caused significant shifts of the crystallization yield. An increase of the polyethylene glycol content from 2% (w/v) to 4% (w/v) increased the yield from approximately 63-87%, respectively. Our results show that crystallization in aqueous two-phase systems is an opportunity to foster process integration.

  5. Enrichment of membrane proteins by partitioning in detergent/polymer aqueous two-phase systems.

    Science.gov (United States)

    Everberg, Henrik; Gustavasson, Niklas; Tjerned, Folke

    2008-01-01

    Methods that combine efficient solubilization with enrichment of proteins and intact protein complexes are of central interest in current membrane proteomics. We have developed methods based on nondenaturing detergent extraction of yeast mitochondrial membrane proteins followed by enrichment of hydrophobic proteins in aqueous two-phase system. Combining the zwitterionic detergent Zwittergent 3-10 and the nonionic detergent Triton X-114 results in a complementary solubilization of proteins, which is similar to that of the anionic detergent sodium dodecyl sulfate (SDS) but with the important advantage of being nondenaturing. Detergent/polymer two-phase system partitioning offers removal of soluble proteins that can be further improved by manipulation of the driving forces governing protein distribution between the phases. Integral and peripheral membrane protein subunits from intact membrane protein complexes partition to the detergent phase while soluble proteins are found in the polymer phase. An optimized solubilization protocol is presented in combination with detergent/polymer two-phase partitioning as a mild and efficient method for initial enrichment of membrane proteins and membrane protein complexes in proteomic studies.

  6. Design of functional guanidinium ionic liquid aqueous two-phase systems for the efficient purification of protein.

    Science.gov (United States)

    Ding, Xueqin; Wang, Yuzhi; Zeng, Qun; Chen, Jing; Huang, Yanhua; Xu, Kaijia

    2014-03-07

    A series of novel cationic functional hexaalkylguanidinium ionic liquids and anionic functional tetraalkylguanidinium ionic liquids have been devised and synthesized based on 1,1,3,3-tetramethylguanidine. The structures of the ionic liquids (ILs) were confirmed by (1)H nuclear magnetic resonance ((1)H NMR) and 13C nuclear magnetic resonance (13C NMR) and the production yields were all above 90%. Functional guanidinium ionic liquid aqueous two-phase systems (FGIL-ATPSs) have been first designed with these functional guanidinium ILs and phosphate solution for the purification of protein. After phase separation, proteins had transferred into the IL-rich phase and the concentrations of proteins were determined by measuring the absorbance at 278 nm using an ultra violet visible (UV-vis) spectrophotometer. The advantages of FGIL-ATPSs were compared with ordinary ionic liquid aqueous two-phase systems (IL-ATPSs). The proposed FGIL-ATPS has been applied to purify lysozyme, trypsin, ovalbumin and bovine serum albumin. Single factor experiments were used to research the effects of the process, such as the amount of ionic liquid (IL), the concentration of salt solution, temperature and the amount of protein. The purification efficiency reaches to 97.05%. The secondary structure of protein during the experimental process was observed upon investigation using UV-vis spectrophotometer, Fourier-transform infrared spectroscopy (FT-IR) and circular dichroism spectrum (CD spectrum). The precision, stability and repeatability of the process were investigated. The mechanisms of purification were researched by dynamic light scattering (DLS), determination of the conductivity and transmission electron microscopy (TEM). It was suggested that aggregation and embrace phenomenon play a significant role in the purification of proteins. All the results show that FGIL-ATPSs have huge potential to offer new possibility in the purification of proteins.

  7. Fractionation of wheat gliadins by counter-current distribution using an organic two-phase system.

    Science.gov (United States)

    Truust, H; Johansson, G

    1998-06-26

    A liquid liquid two-phase system based on N,N-dimethylformamide and the two polymers, poly(ethyleneglycol) and Ficoll, useful for partitioning of hydrophobic proteins, has been developed. The system has been applied to a counter-current distribution process in 56 steps for analysing the heterogeneity of proteins extracted with N,N-dimethylformamide from wheat flour. The counter-current distribution patterns of proteins, extracted from eight kinds of wheat, have been analysed. The minimum number of hypothetical proteins necessary to describe the patterns was found to be seven. The relative amount of these hypothetical components varied among the wheats.

  8. Two-Phase Cryogenic Heat Exchanger for the Thermodynamic Vent System

    Science.gov (United States)

    Christie, Robert J.

    2011-01-01

    A two-phase cryogenic heat exchanger for a thermodynamic vent system was designed and analyzed, and the predicted performance was compared with test results. A method for determining the required size of the Joule-Thomson device was also developed. Numerous sensitivity studies were performed to show that the design was robust and possessed a comfortable capacity margin. The comparison with the test results showed very similar heat extraction performance for similar inlet conditions. It was also shown that estimates for Joule- Thomson device flow rates and exit quality can vary significantly and these need to be accommodated for with a robust system design.

  9. Extraction of penicillin G by aqueous two-phase system of [Bmim]BF4/NaH2PO4

    Institute of Scientific and Technical Information of China (English)

    LIU Qingfen; HU Xuesheng; WANG Yuhong; YANG Ping; XIA Hansong; YU Jiang; LIU Huizhou

    2005-01-01

    A novel approach for the extraction of penicillin G by aqueous two-phase system comprised of hydrophilic ionic liquid [Bmim]BF4 (1-butyl-3- methylimidazolium tetrafluoroborate) and NaH2PO4 is reported. The effects of some important parameters involving the concentration of NaH2PO4, the concentration of penicillin G, the amount of [Bmim]BF4 on the formation of aqueous two-phase system and the extraction yield of penicillin were investigated. The primary result shows that the ATPS can take advantage of penicillin concentrated in upper phase at higher pH value for penicillin extraction from its aqueous solution without emulsification.

  10. Design of functional guanidinium ionic liquid aqueous two-phase systems for the efficient purification of protein

    Energy Technology Data Exchange (ETDEWEB)

    Ding, Xueqin; Wang, Yuzhi, E-mail: wyzss@hnu.edu.cn; Zeng, Qun; Chen, Jing; Huang, Yanhua; Xu, Kaijia

    2014-03-01

    Graphical abstract: - Highlights: • A series of novel cationic functional hexaalkylguanidinium ionic liquids and anionic functional tetraalkylguanidinium ionic liquids have been synthesized. • Functional guanidinium ionic liquid aqueous two-phase systems have been first designed for the purification of protein. • Mechanisms and performances of the process were researched. • Simple, green, safety and presents better purified ability than ordinary process. • A potential efficient platform for protein purification and related studies. - Abstract: A series of novel cationic functional hexaalkylguanidinium ionic liquids and anionic functional tetraalkylguanidinium ionic liquids have been devised and synthesized based on 1,1,3,3-tetramethylguanidine. The structures of the ionic liquids (ILs) were confirmed by {sup 1}H nuclear magnetic resonance ({sup 1}H NMR) and 13C nuclear magnetic resonance (13C NMR) and the production yields were all above 90%. Functional guanidinium ionic liquid aqueous two-phase systems (FGIL-ATPSs) have been first designed with these functional guanidinium ILs and phosphate solution for the purification of protein. After phase separation, proteins had transferred into the IL-rich phase and the concentrations of proteins were determined by measuring the absorbance at 278 nm using an ultra violet visible (UV–vis) spectrophotometer. The advantages of FGIL-ATPSs were compared with ordinary ionic liquid aqueous two-phase systems (IL-ATPSs). The proposed FGIL-ATPS has been applied to purify lysozyme, trypsin, ovalbumin and bovine serum albumin. Single factor experiments were used to research the effects of the process, such as the amount of ionic liquid (IL), the concentration of salt solution, temperature and the amount of protein. The purification efficiency reaches to 97.05%. The secondary structure of protein during the experimental process was observed upon investigation using UV–vis spectrophotometer, Fourier-transform infrared

  11. Partitioning of L-methionine in aqueous two-phase systems containing poly(propylene glycol) and sodium phosphate salts

    Energy Technology Data Exchange (ETDEWEB)

    Salabat, Alireza, E-mail: a-salabat@araku.ac.ir [Chemistry Department, Arak University, P.O. Box 38156-879, Arak (Iran, Islamic Republic of); Sadeghi, Rahmat [Department of Chemistry, University of Kurdistan, Sanandaj, Kurdistan 66135 (Iran, Islamic Republic of); Moghadam, Somayeh Tiani [Chemistry Department, Arak University, P.O. Box 38156-879, Arak (Iran, Islamic Republic of); Jamehbozorg, Bahman [Department of Chemistry, University of Kurdistan, Sanandaj, Kurdistan 66135 (Iran, Islamic Republic of)

    2011-10-15

    Highlights: > Thermodynamics parameters for partitioning of L-methionine in ATPS. > Investigation of different effects on partition coefficient of the amino acid. > Propose the best condition for L-methionine partitioning. - Abstract: The partitioning behavior of L-methionine has been studied in aqueous two-phase systems of (poly(propylene glycol) + sodium phosphate salts + H{sub 2}O) at different temperatures. The salts used were sodium di-hydrogen phosphate (NaH{sub 2}PO{sub 4}), di-sodium hydrogen phosphate (Na{sub 2}HPO{sub 4}) and tri-sodium phosphate (Na{sub 3}PO{sub 4}). The effects of tie line length, salt type, and temperature on the partition coefficient of this amino acid have been studied. In addition, thermodynamic parameters ({Delta}H{sup o}, {Delta}S{sup o} and {Delta}G{sup o}) as a function of temperature were calculated. The results showed that increasing tie line length led to decreasing of the partition coefficient. We also showed that the partition coefficients of the amino acid in the systems containing Na{sub 3}PO{sub 4} are greater than the other two salts. Moreover, it is verified that increasing temperature led to decreasing the partition coefficient. The experimental partition coefficient data are correlated using a modified virial-type model.

  12. Aqueous Two-Phase Extraction of Polyphenols Using a Microchannel System – Process Optimization and Intensification

    Directory of Open Access Journals (Sweden)

    Ivana Rukavina

    2011-01-01

    Full Text Available Polyphenols are one of the most numerous and widespread groups of compounds in the plant world. Nowadays, organic solvents such as methanol, ethanol, acetone, dimethylformamide, ethyl acetate and diethylether are mainly used for the extraction of polyphenols. These solvents require special process conditions and special care in the disposal of the used solvents. In this paper, the extraction of polyphenols from the model solution was performed using the aqueous two-phase system which contains 80.90 % water and represents low burden on the environment. The aqueous solution of gallic acid (GA was used as a model solution of polyphenols. The extraction was performed in the aqueous two-phase system containing PEG6000/H2O/(NH42SO4 in a macroextractor (V=10 mL and microextractor (V=14 ƒμL. The influence of the process parameters, the concentration of gallic acid, pH and composition of the aqueous two-phase system was investigated in order to maximize the partition coefficient. The method of multifactor experimental planning was used to optimize the extraction process and the results were statistically analysed using the evolutionary operation method (EVOP. Optimal operating conditions of the extraction process were pH=6.50, γGA=4.50 g/L, the mass fraction of polyethylene glycol (PEG wPEG=0.1037 g/g and the mass fraction of ammonium sulphate (AMS wAMS=0.0925 g/g. Under these conditions the maximal partition coefficient of K=5.54 and the extraction efficiency of E=89.11 % were achieved and successfully applied for total phenol extraction from white wine in the macro- and microextractor. Approximately the same partition coefficients and extraction efficiency were achieved in the microextractor within a 60-fold shorter residence time.

  13. Influence of the temperature and type of salt on the phase equilibrium of peg 1500 + potassium phosphate and peg 1500 + sodium citrate aqueous two-phase systems

    Directory of Open Access Journals (Sweden)

    Carolina P. Carvalho

    2008-01-01

    Full Text Available The present work analyzed the effect of the temperature and type of salt on the phase equilibrium of aqueous two-phase systems (ATPS formed by poly (ethylene glycol (PEG 1500 + potassium phosphate, from (278.15 to 318.15 K, and PEG 1500 + sodium citrate, from (278.15 to 298.15 K. The rise of the temperature normally increased the slope of the tie line (STL. With respect to the influence of the type of salt, sodium citrate showed better capability to induce phase separation, when compared to potassium phosphate.

  14. Integration of bioconversion and downstream processing: starch hydrolysis in an aqueous two-phase system.

    Science.gov (United States)

    Larsson, M; Arasaratnam, V; Mattiasson, B

    1989-02-05

    Integration of bioconversion and the first step(s) of down stream processing can be used as a means to increase the productivity of bioprocesses. This integration also gives the possibility to run the bioconversion in a continuous mode. We demonstrate the use of an aqueous two-phase system in combination with ultrafiltration to accomplish this. Conversion of native starch to glucose by alpha-amylase and glucoamylase was carried out in an aqueous two-phase system in connection with a membrane filtration unit. In this way, a continuous stream of glucose in buffer solution was obtained; the phase-forming polymers as well as the starch-degrading enzymes were recycled, and clogging of the ultrafiltration membrane was avoided. The process was carried out continuously in a mixer-settler reactor for a period of 8 days. The enzyme activities in the top and bottom phases and in the mixing chamber were monitored intermittently throughout the experiment. The optimum pH, temperature, and ionic strength for the activity of the enzyme mixture were determined. The settling time of phase systems containing varying amounts of PEG, crude dextran, and solid starch was studied. The activity and stability of enzyme mixtures was studied both in buffer medium and in the medium containing the polymers. The enzymes were found to be more active and stable in medium containing polymers than in the buffer solutions.

  15. Aqueous two-phase system patterning of detection antibody solutions for cross-reaction-free multiplex ELISA

    Science.gov (United States)

    Frampton, John P.; White, Joshua B.; Simon, Arlyne B.; Tsuei, Michael; Paczesny, Sophie; Takayama, Shuichi

    2014-05-01

    Accurate disease diagnosis, patient stratification and biomarker validation require the analysis of multiple biomarkers. This paper describes cross-reactivity-free multiplexing of enzyme-linked immunosorbent assays (ELISAs) using aqueous two-phase systems (ATPSs) to confine detection antibodies at specific locations in fully aqueous environments. Antibody cross-reactions are eliminated because the detection antibody solutions are co-localized only to corresponding surface-immobilized capture antibody spots. This multiplexing technique is validated using plasma samples from allogeneic bone marrow recipients. Patients with acute graft versus host disease (GVHD), a common and serious condition associated with allogeneic bone marrow transplantation, display higher mean concentrations for four multiplexed biomarkers (HGF, elafin, ST2 and TNFR1) relative to healthy donors and transplant patients without GVHD. The antibody co-localization capability of this technology is particularly useful when using inherently cross-reactive reagents such as polyclonal antibodies, although monoclonal antibody cross-reactivity can also be reduced. Because ATPS-ELISA adapts readily available antibody reagents, plate materials and detection instruments, it should be easily transferable into other research and clinical settings.

  16. Interrelationship between partition behavior of organic compounds and proteins in aqueous dextran-polyethylene glycol and polyethylene glycol-sodium sulfate two-phase systems.

    Science.gov (United States)

    Ferreira, Luisa A; da Silva, Nuno R; Wlodarczyk, Samarina R; Loureiro, Joana A; Madeira, Pedro P; Teixeira, José A; Uversky, Vladimir N; Zaslavsky, Boris Y

    2016-04-22

    Partition behavior of adenosine and guanine mononucleotides was examined in aqueous dextran-polyethylene glycol (PEG) and PEG-sodium sulfate two-phase systems. The partition coefficients for each series of mononucleotides were analyzed as a functions of the number of phosphate groups and found to be dependent on the nature of nucleic base and on the type of ATPS utilized. It was concluded that an average contribution of a phosphate group into logarithm of partition coefficient of a mononucleotide cannot be used to estimate the difference between the electrostatic properties of the coexisting phases of ATPS. The data obtained in this study were considered together with those for other organic compounds and proteins reported previously, and the linear interrelationship between logarithms of partition coefficients in dextran-PEG, PEG-Na2SO4 and PEG-Na2SO4-0.215M NaCl (all in 0.01M Na- or K/Na-phosphate buffer, pH 7.4 or 6.8) was established. Similar relationship was found for the previously reported data for proteins in Dex-PEG, PEG-600-Na2SO4, and PEG-8000-Na2SO4 ATPS. It is suggested that the linear relationships of the kind established in ATPS may be observed for biological properties of compounds as well.

  17. Ionic Liquid-Based Ultrasonic-Assisted Extraction of Secoisolariciresinol Diglucoside from Flaxseed (Linum usitatissimum L.) with Further Purification by an Aqueous Two-Phase System.

    Science.gov (United States)

    Tan, Zhi-Jian; Wang, Chao-Yun; Yang, Zi-Zhen; Yi, Yong-Jian; Wang, Hong-Ying; Zhou, Wan-Lai; Li, Fen-Fang

    2015-09-30

    In this work, a two-step extraction methodology of ionic liquid-based ultrasonic-assisted extraction (IL-UAE) and ionic liquid-based aqueous two-phase system (IL-ATPS) was developed for the extraction and purification of secoisolariciresinol diglucoside (SDG) from flaxseed. In the IL-UAE step, several kinds of ILs were investigated as the extractants, to identify the IL that affords the optimum extraction yield. The extraction conditions such as IL concentration, ultrasonic irradiation time, and liquid-solid ratio were optimized using response surface methodology (RSM). In the IL-ATPS step, ATPS formed by adding kosmotropic salts to the IL extract was used for further separation and purification of SDG. The most influential parameters (type and concentration of salt, temperature, and pH) were investigated to obtain the optimum extraction efficiency. The maximum extraction efficiency was 93.35% under the optimal conditions of 45.86% (w/w) IL and 8.27% (w/w) Na₂SO₄ at 22 °C and pH 11.0. Thus, the combination of IL-UAE and IL-ATPS makes up a simple and effective methodology for the extraction and purification of SDG. This process is also expected to be highly useful for the extraction and purification of bioactive compounds from other important medicinal plants.

  18. Salt effect on the (polyethylene glycol 8000 + sodium sulfate) aqueous two-phase system: Relative hydrophobicity of the equilibrium phases

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Luisa A., E-mail: laferreira@deb.uminho.pt [IBB - Institute for Biotechnology and Bioengineering, Centre for Biological Engineering, Universidade do Minho, Campus de Gualtar, 4710-057 Braga (Portugal); Teixeira, Jose A. [IBB - Institute for Biotechnology and Bioengineering, Centre for Biological Engineering, Universidade do Minho, Campus de Gualtar, 4710-057 Braga (Portugal)

    2011-08-15

    Highlights: > Gibbs free energy of transfer of a methylene group on PEG 8000 - Na{sub 2}SO{sub 4} ATPS. > Influence of salt additive on the hydrophobic character of the coexisting phases. > Partitioning behavior of a series of five sodium salts of DNP-amino acids. > A relationship between {Delta}G(CH{sub 2}), TLL and I of the salt additive was established. - Abstract: The relative hydrophobicity of the phases of several {l_brace}polyethylene glycol (PEG) 8000 + sodium sulfate (Na{sub 2}SO{sub 4}){r_brace} aqueous two-phase systems (ATPSs), all containing 0.01 mol . L{sup -1} sodium phosphate buffer (NaPB, pH 7.4) and increasing concentration of a salt additive, NaCl or KCl, up to 1.0 mol . L{sup -1}, was measured by the free energy of transfer of a methylene group between the phases, {Delta}G(CH{sub 2}). The {Delta}G(CH{sub 2}) of the systems was determined by partitioning of a homologous series of five sodium salts of dinitrophenylated (DNP) - amino acids with aliphatic side chains in three different tie-lines of each biphasic system. The relative hydrophobicity of the phases ranged from -0.125 to -0.183 kcal . mol{sup -1}, being the NaCl salt the one to provide the more effective changes. The results show that, within each system, there is a linear relationship between the {Delta}G(CH{sub 2}) and the tie-line length (TLL), and biphasic systems with high salt additive concentration present the most negative {Delta}G(CH{sub 2}) values. Therefore, the feasibility of establishing a relationship between the relative hydrophobicity of the phases in a given TLL and the ionic strength of the salt additive was investigated and a satisfactory correlation was found for each salt.

  19. Bromelain purification through unconventional aqueous two-phase system (PEG/ammonium sulphate).

    Science.gov (United States)

    Coelho, D F; Silveira, E; Pessoa Junior, A; Tambourgi, E B

    2013-02-01

    This paper focuses on the feasibility of unconventional aqueous two-phase systems for bromelain purification from pineapple processing waste. The main difference in comparison with conventional systems is the integration of the liquid-liquid extraction technique with fractional precipitation, which can decrease the protein content with no loss of biological activity by removing of unwanted molecules. The analysis of the results was based on the response surface methodology and revealed that the use of the desirability optimisation methodology (DOM) was necessary to achieve higher purification factor values and greater bromelain recovery. The use of DOM yielded an 11.80-fold purification factor and 66.38 % biological activity recovery using poly(ethylene glycol) (PEG) with a molar mass of 4,000, 10.86 % PEG concentration (m/m) and 36.21 % saturation of ammonium sulphate.

  20. Analysis of a pneumatic system for a two-phase flow sugar

    Directory of Open Access Journals (Sweden)

    G OteroR

    2016-09-01

    Full Text Available This document shows a complete analysis the transportation of sugar particles by a pneumatic conveying station. This project shows an actual situation presenting in a food plant located in Aragua, Venezuela, where the sugar piping system suffers continuous obstructions. It was achieved an effective analysis of the phenomenon of solid-gas two-phase flow transport which involves a complex physics phenomenon. Two possible obstruction causes was studied: the high temperature at the blower exit that induces changes in the sugar properties caused by the working condition far from the designed operation condition, or the excessive friction losses, due to the system is working out of the dilute phase condition (optimal condition for the flow. The mathematical model described allowed to determine that the cause of the obstruction of the pipeline was the stick of the sugar to the internal wall, as consequence of this high temperature at the outlet of the blower.

  1. An Aqueous Two-Phase System for the Concentration and Extraction of Proteins from the Interface for Detection Using the Lateral-Flow Immunoassay.

    Directory of Open Access Journals (Sweden)

    Ricky Y T Chiu

    Full Text Available The paper-based immunoassay for point-of-care diagnostics is widely used due to its low cost and portability over traditional lab-based assays. Lateral-flow immunoassay (LFA is the most well-established paper-based assay since it is rapid and easy to use. However, the disadvantage of LFA is its lack of sensitivity in some cases where a large sample volume is required, limiting its use as a diagnostic tool. To improve the sensitivity of LFA, we previously reported on the concentration of analytes into one of the two bulk phases of an aqueous two-phase system (ATPS prior to detection. In this study, we preserved the advantages of LFA while significantly improving upon our previous proof-of-concept studies by employing a novel approach of concentrating gold nanoparticles, a common LFA colorimetric indicator. By conjugating specific antibodies and polymers to the surfaces of the particles, these gold nanoprobes (GNPs were able to capture target proteins in the sample and subsequently be concentrated within 10 min at the interface of an ATPS solution comprised of polyethylene glycol, potassium phosphate, and phosphate-buffered saline. These GNPs were then extracted and applied directly to LFA. By combining this prior ATPS interface extraction with LFA, the detection limit of LFA for a model protein was improved by 100-fold from 1 ng/μL to 0.01 ng/μL. Additionally, we examined the behavior of the ATPS system in fetal bovine serum and synthetic urine to more closely approach real-world applications. Despite using more complex matrices, ATPS interface extraction still improved the detection limit by 100-fold within 15 to 25 min, demonstrating the system's potential to be applied to patient samples.

  2. Enzymatic hydrolysis of penicillin in mixed ionic liquids/water two-phase system.

    Science.gov (United States)

    Jiang, Yangyang; Xia, Hansong; Guo, Chen; Mahmood, Iram; Liu, Huizhou

    2007-01-01

    In this paper, an integrated process involving the mixed ionic liquids/water two-phase system (MILWS) is proposed to improve the efficiency for enzymatic hydrolysis of penicillin G. First, hydrophilic [C4mim]BF4 (1-butyl-3-methylimidazolium tetrafluoraborate) and NaH2PO4 salt form an ionic liquids aqueous two-phase system (ILATPS), which could extract penicillin from its fermentation broth efficiently. Second, a hydrophobic [C4mim]PF6 (1-butyl-3-methylimidazolium hexafluoraphosphate) is introduced into the ionic liquids-rich phase of ILATPS containing penicillin and converses it into MILWS. Penicillin is hydrolyzed by penicillin acylase in the water phase of MILWS at pH 5. The byproduct phenylacetic acid (PAA) is partitioned into the ionic liquids mixture phase, while the intended product 6-aminopenicillanic acid (6-APA) is precipitated at this pH. In comparison with a similar butyl acetate/water system (BAWS) at pH 4, MILWS exhibits two advantages. (1) The selectivity between PAA and penicillin is greatly optimized at pH 5 by varying the mole ratio of [C4mim]PF6/[C4mim]BF4 in MILWS, whereas in BAWS the unalterable nature of the organic solvent restricts the optimized pH for maximum selectivity between PAA and penicillin at pH 4. (2) The pH for 6-APA precipitation in BAWS is 4, whereas it shifts to pH 5 in MILWS due to the complexation between negatively charged 6-APA and the cationic surface of the ionic liquids micelle. As a result, the removal of the two products from the enzyme sphere at relatively high pH is permitted in MILWS, which is beneficial for enzymatic activity and stability in comparison with the acidic pH 4 environment in BAWS.

  3. Ionic Liquid-salt Aqueous Two-phase System, a Novel System for the Extraction of Abused Drugs

    Institute of Scientific and Technical Information of China (English)

    She Hong LI; Chi Yang HE; Hu Wei LIU; Ke An LI; Feng LIU

    2005-01-01

    A 1-butyl-3-methylimidazolium chloride-salt aqueous two-phase system was studied on extraction of abused drugs. The effects of sorts of salts, temperature, concentration of salt and drugs on system were investigated systematically. A satisfactory extraction efficiency of 93%was obtained for papaverine while that of morphine was 65%. The extraction mechanism was primarily discussed.

  4. Optimizing steam flood performance utilizing a new and highly accurate two phase steam measurement system

    Energy Technology Data Exchange (ETDEWEB)

    Huff, B. D.; Warren, P. B. [CalResources LLC (Canada); Whorff, F. [ITT Barton (Canada)

    1995-11-01

    The development of a two phase steam measurement system was documented. The system consists of a `V` cone differential pressure device and a vortex meter velocity device in series through which the steam flows. Temperature and pressure sensors are electronically interfaced with a data logging system. The design was described as being very simple and rugged, consequently, well suited to monitoring in the field.. Steam quality measurements were made in the Kern River Field and the Coalinga Field thermal projects using a surface steam separator. In steam flood operations, steam cost is very high, hence appropriate distribution of the steam can result in significant cost reduction. This technology allows the measurement of steam flow and quality at any point in the steam distribution system. The metering system`s orifice meter was found to have a total average error of 45%, with 25% of that attributable to `cold leg` problem. Installation of the metering system was expected to result in a steam use reduction of 8%, without any impact on production. Steam re-distribution could result in a potential oil production increase of 10%. 12 refs., 8 tabs., 9 figs.

  5. Reaction Mechanisms and Particle Interaction in Burning Two-Phase Systems

    Science.gov (United States)

    Dreizin, Edward L.; Shoshin, Yuriy L.; Murdyy, Ruslan S.; Hoffmann, Vern K.

    2001-01-01

    The main objective of this research is to understand the mechanisms by which particle interactions affect ignition and combustion in the two-phase systems. Combustion of metal aerosols representing the two-phase systems is carried out in the microgravity environment enabling one to avoid the buoyant flows that mask the particle motion due to the particle-particle interaction effects. In addition, relatively large, e.g., 100 micron diameter particles can be used, that remain aerosolized (i.e., do not fall down as they would at normal gravity) so that their behavior ahead, behind, and within the propagating flame can be resolved optically. An experimental apparatus exploiting this approach has been designed for the 2.2-s drop tower microgravity experiments. A typical experiment includes fluidizing metal particles under microgravity in an acoustic field, turning off the acoustic exciter, and igniting the created aerosol at a constant pressure using a hot wire igniter. The flame propagation and details of the individual particle combustion and particle interactions are studied using high-speed movie and video cameras coupled with microscope lenses to resolve individual particles. Recorded flame images are digitized and various image processing techniques including flame position tracking, color separation, and pixel by pixel image comparisons are employed to understand the processes occurring in the burning aerosols. Condensed combustion products are collected after each experiment for the phase, composition, and morphology analyses. New experiments described in this paper address combustion of Ti and Al particle clouds in air and combustion of Mg particle clouds in CO2. In addition, microgravity combustion experiments have been conducted with the particles of the newly produced Al-Mg mechanical alloys aerosolized in air.

  6. A method for dye extraction using an aqueous two-phase system: Effect of co-occurrence of contaminants in textile industry wastewater.

    Science.gov (United States)

    Borges, Gabriella Alexandre; Silva, Luciana Pereira; Penido, Jussara Alves; de Lemos, Leandro Rodrigues; Mageste, Aparecida Barbosa; Rodrigues, Guilherme Dias

    2016-12-01

    This paper reports a green and efficient procedure for extraction of the dyes Malachite Green (MG), Methylene Blue (MB), and Reactive Red 195 (RR) using an aqueous two-phase system (ATPS). An ATPS consists mainly of water, together with polymer and salt, and does not employ any organic solvent. The extraction efficiency was evaluated by means of the partition coefficients (K) and residual percentages (%R) of the dyes, under different experimental conditions, varying the tie-line length (TLL) of the system, the pH, the type of ATPS-forming electrolyte, and the type of ATPS-forming polymer. For MG, the best removal (K = 4.10 × 10(4), %R = 0.0069%) was obtained with the ATPS: PEO 1500 + Na2C4H4O6 (TLL = 50.21% (w/w), pH = 6.00). For MB, the maximum extraction (K = 559.9, %R = 0.258%) was achieved with the ATPS: PEO 400 + Na2SO4 (TLL = 50.31% (w/w), pH = 1.00). Finally for RR, the method that presented the best results (K = 3.75 × 10(4), %R = 0.237%) was the ATPS: PEO 400 + Na2SO4 (TLL = 50.31% (w/w), pH = 6.00). The method was applied to the recovery of these dyes from a textile effluent sample, resulting in values of K of 1.17 × 10(4), 724.1, and 3.98 × 10(4) for MG, MB, and RR, respectively, while the corresponding %R values were 0.0038, 0.154, and 0.023%, respectively. In addition, the ATPS methodology provided a high degree of color removal (96.5-97.95%) from the textile effluent. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. Space qualification of an experimental two-phase flow thermal management system

    Science.gov (United States)

    Koonmen, James P.; Carswell, Lisa C.; Kvansnak, Michael A.

    1991-01-01

    The Weapons Laboratory will launch a space experiment in March 1991 to investigate the effects of extended microgravity on two-phase (liquid/vapor) flow. The qualification process for the experimental flight system hardware differs significantly from the process used for complex, high cost, long life space systems. Some development, qualification, and acceptance tests normally included in the test program of an operational space system were omitted because of the low program cost and low consequence of experiment failure. Key environment and functional qualification tests were performed, however, in an effort to reduce the risk of failure inherent in any space mission. The environmental qualification program included short duration vacuum chamber tests, reduced gravity missions onboard a National Aeronautics and Space Administration (NASA) test aircraft, and a complete series of shock and vibration tests. The functional qualification program centered on thermal-hydraulic system performance tests and a complete check-out of the unique telemetry system used to retrieve the experimental data from the payload. The test program also contains a number of acceptance and prelaunch validation tests to be performed as final verification of payloads readiness for spaceflight.

  8. Two-phase equilibrium and molecular hydrogen formation in damped Lyman-alpha systems

    CERN Document Server

    Liszt, H S

    2002-01-01

    Molecular hydrogen is quite underabundant in damped Lyman-alpha systems at high redshift, when compared to the interstellar medium near the Sun. This has been interpreted as implying that the gas in damped Lyman-alpha systems is warm. like the nearby neutral intercloud medium, rather than cool, as in the clouds which give rise to most H I absorption in the Milky Way. Other lines of evidence suggest that the gas in damped Lyman-alpha systems -- in whole or part -- is actually cool; spectroscopy of neutral and ionized carbon, discussed here, shows that the damped Lyman-alpha systems observed at lower redshift z $$ 2.8 are warm (though not devoid of H2). To interpret the observations of carbon and hydrogen we constructed detailed numerical models of H2 formation under the conditions of two-phase thermal equilibrium, like those which account for conditions near the Sun, but with varying metallicity, dust-gas ratio, $etc$. We find that the low metallicity of damped Lyman-alpha systems is enough to suppress H2 form...

  9. Molecular features determining different partitioning patterns of papain and bromelain in aqueous two-phase systems.

    Science.gov (United States)

    Rocha, Maria Victoria; Nerli, Bibiana Beatriz

    2013-10-01

    The partitioning patterns of papain (PAP) and bromelain (BR), two well-known cysteine-proteases, in polyethyleneglycol/sodium citrate aqueous two-phase systems (ATPSs) were determined. Polyethyleneglycols of different molecular weight (600, 1000, 2000, 4600 and 8000) were assayed. Thermodynamic characterization of partitioning process, spectroscopy measurements and computational calculations of protein surface properties were also carried out in order to explain their differential partitioning behavior. PAP was observed to be displaced to the salt-enriched phase in all the assayed systems with partition coefficients (KpPAP) values between 0.2 and 0.9, while BR exhibited a high affinity for the polymer phase in systems formed by PEGs of low molecular weight (600 and 1000) with partition coefficients (KpBR) values close to 3. KpBR values resulted higher than KpPAP in all the cases. This difference could be assigned neither to the charge nor to the size of the partitioned biomolecules since PAP and BR possess similar molecular weight (23,000) and isoelectric point (9.60). The presence of highly exposed tryptophans and positively charged residues (Lys, Arg and His) in BR molecule would be responsible for a charge transfer interaction between PEG and the protein and, therefore, the uneven distribution of BR in these systems.

  10. Potential application of aqueous two-phase systems and three-phase partitioning for the recovery of superoxide dismutase from a clarified homogenate of Kluyveromyces marxianus.

    Science.gov (United States)

    Simental-Martínez, Jesús; Rito-Palomares, Marco; Benavides, Jorge

    2014-01-01

    Superoxide dismutase (SOD; EC 1.15.1.1) is an antioxidant enzyme that represents the primary cellular defense against superoxide radicals and has interesting applications in the medical and cosmetic industries. In the present work, the partition behavior of SOD in aqueous two-phase systems (ATPS) (using a standard solution and a complex extract from Kluyveromyces marxianus as sample) was characterized on different types of ATPS (polymer-polymer, polymer-salt, alcohol-salt, and ionic liquid (IL)-salt). The systems composed of PEG 3350-potassium phosphate, 45% TLL, 0.5 M NaCl (315 U/mg, 87% recovery, and 15.1-fold purification) and t-butanol-20% ammonium sulfate (205.8 U/mg, 80% recovery and 9.8-fold purification), coupled with a subsequent 100 kDa ultrafiltration stage, allowed the design of a prototype process for the recovery and partial purification of the product of interest. The findings reported herein demonstrate the potential of PEG-salt ATPS for the potential recovery of SOD.

  11. A novel aqueous micellar two-phase system composed of surfactant and sorbitol for purification of pectinase enzyme from Psidium guajava and recycling phase components.

    Science.gov (United States)

    Amid, Mehrnoush; Murshid, Fara Syazana; Manap, Mohd Yazid; Hussin, Muhaini

    2015-01-01

    A novel aqueous two-phase system composed of a surfactant and sorbitol was employed for the first time to purify pectinase from Psidium guajava. The influences of different parameters, including the type and concentration of the surfactant and the concentration and composition of the surfactant/sorbitol ratio, on the partitioning behavior and recovery of pectinase were investigated. Moreover, the effects of system pH and the crude load on purification fold and the yield of purified pectinase were studied. The experimental results indicated that the pectinase was partitioned into surfactant-rich top phase, and the impurities were partitioned into the sorbitol-rich bottom phase with the novel method involving an ATPS composed of 26% (w/w) Triton X-100 and 23% (w/w) sorbitol at 54.2% of the TLL crude load of 20% (w/w) at pH 6.0. The enzyme was successfully recovered by this method with a high purification factor of 15.2 and a yield of 98.3%, whereas the phase components were also recovered and recycled at rates above 96%. This study demonstrated that this novel ATPS method can be used as an efficient and economical alternative to the traditional ATPS for the purification and recovery of the valuable enzyme.

  12. Stability of clavulanic acid in PEG/citrate and liquid–liquid extraction in aqueous two-phase system

    OpenAIRE

    Carneiro-da-Cunha, M. N.; Souza, K. P. S.; Mota, A; J.A. Teixeira; Porto, C S; Porto, Tatiana Souza; Porto, Ana L. F.

    2014-01-01

    β-Lactamases are enzymes responsible for the hydrolysis of β-lactam antibiotics, being produced by several pathogenic bacteria. Clavulanic acid is a commercially and clinically important β-lactamase inhibitor, its extraction being possible by the application of aqueous two-phase system. In this study, clavulanic acid stability was investigated at different molar mass PEG (400, 1 000 and 20 000 g mol−1) and at different citrate concentrations (5 and 20%) PEG/citrate aqueous-two phase systems (...

  13. LPS removal from an E. coli fermentation broth using aqueous two-phase micellar system.

    Science.gov (United States)

    Lopes, André M; Magalhães, Pérola O; Mazzola, Priscila G; Rangel-Yagui, Carlota O; de Carvalho, João C M; Penna, Thereza C V; Pessoa, Adalberto

    2010-01-01

    In biotechnology, endotoxin (LPS) removal from recombinant proteins is a critical and challenging step in the preparation of injectable therapeutics, as endotoxin is a natural component of bacterial expression systems widely used to manufacture therapeutic proteins. The viability of large-scale industrial production of recombinant biomolecules of pharmaceutical interest significantly depends on the separation and purification techniques used. The aim of this work was to evaluate the use of aqueous two-phase micellar system (ATPMS) for endotoxin removal from preparations containing recombinant proteins of pharmaceutical interest, such as green fluorescent protein (GFPuv). Partition assays were carried out initially using pure LPS, and afterwards in the presence of E. coli cell lysate. The ATPMS technology proved to be effective in GFPuv recovery, preferentially into the micelle-poor phase (K(GFPuv) 98.00%). Therefore, this system can be exploited as the first step for purification in biotechnology processes for removal of higher LPS concentrations. Copyright © 2010 American Institute of Chemical Engineers (AIChE).

  14. Drift flux modelling for a two-phase system in a flotation column

    Energy Technology Data Exchange (ETDEWEB)

    Vandenberghe, J.; Choung, J.; Xu, Z.; Masliyah, J. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering

    2005-04-01

    Mineral and coal industries use flotation columns to improve recovery, upgrade products, save energy and reduce scale. Flotation columns are a proven process equipment that are adaptable to computer process control and offer flexible operation. Once gas is introduced to the bottom of the flotation column, bubbles form and rise throughout the pulp. Hydrophobic particles in the pulp attache to the bubbles, making the density of the bubble particle aggregates less than that of the medium. The bubble zone and the froth zone are the 2 main zones of a flotation column. This study applied the drift flux analysis to a wide range of operating conditions of a two-phase system column in order develop a better empirical relation that can predict the bubbly and froth zone characteristics. Tests were performed with process water taken from a bitumen extraction process at Syncrude Canada Limited with aqueous solutions having low concentrations of methyl isobutyl carbinol at 7.8 or 15.5 ppm. A new correlation for the drift flux system characteristic curve was discovered in this study. The new correlation is applicable for a bubble Reynolds number range of 5 to 70. The numerical equation for this correlation was presented. The bubble and froth zones have different hydrodynamics. Therefore, the method for calculating the Reynolds number in the bubble zone may not be suitable for the froth zone. Therefore, a new equation was proposed to accommodate a wider operating range. 16 refs., 1 tab., 13 figs.

  15. LPS-protein aggregation influences protein partitioning in aqueous two-phase micellar systems.

    Science.gov (United States)

    Lopes, André Moreni; Santos-Ebinuma, Valéria de Carvalho; Novaes, Leticia Celia de Lencastre; Molino, João Vitor Dutra; Barbosa, Leandro Ramos Souza; Pessoa, Adalberto; Rangel-Yagui, Carlota de Oliveira

    2013-07-01

    Lipopolysaccharide endotoxins (LPS) are the most common pyrogenic substances in recombinant peptides and proteins purified from Gram-negative bacteria, such as Escherichia coli. In this respect, aqueous two-phase micellar systems (ATPMS) have already proven to be a good strategy to purify recombinant proteins of pharmaceutical interest and remove high LPS concentrations. In this paper, we review our recent experimental work in protein partitioning in Triton X-114 ATPMS altogether with some new results and show that LPS-protein aggregation can influence both protein and LPS partitioning. Green fluorescent protein (GFPuv) was employed as a model protein. The ATPMS technology proved to be effective for high loads of LPS removal into the micelle-rich phase (%REM(LPS) > 98 %) while GFPuv partitioned preferentially to the micelle-poor phase (K GFP(uv) system. Nonetheless, ATPMS can still be considered as an efficient strategy for high loads of LPS removal, but being aware that the excluded-volume partitioning theory available might overestimate partition coefficient values due to the presence of protein-LPS aggregation.

  16. Effective thermal conductivity of real two-phase systems using resistor model with ellipsoidal inclusions

    Indian Academy of Sciences (India)

    Jagjiwanram; Ramvir Singh

    2004-08-01

    A theoretical model has been developed for real two-phase system assuming linear flow of heat flux lines having ellipsoidal particles arranged in a three-dimensional cubic array. The arrangement has been divided into unit cells, each of which contains an ellipsoid. The resistor model has been applied to determine the effective thermal conductivity (ETC) of the unit cell. To take account of random packing of the phases, non-uniform shape of the particles and non-linear flow of heat flux lines in real systems, incorporating an empirical correction factor in place of physical porosity modifies an expression for ETC. An effort is made to correlate it in terms of the ratio of thermal conductivities of the constituents and the physical porosity. Theoretical expression so obtained has been tested on a large number of samples cited in the literature and found that the values predicted are quite close to the experimental results. Comparison of our model with different models cited in the literature has also been made.

  17. PEG-salt aqueous two-phase systems: an attractive and versatile liquid-liquid extraction technology for the downstream processing of proteins and enzymes.

    Science.gov (United States)

    Glyk, Anna; Scheper, Thomas; Beutel, Sascha

    2015-08-01

    Nowadays, there is an increasing demand to establish new feasible, efficient downstream processing (DSP) techniques in biotechnology and related fields. Although several conventional DSP technologies have been widely employed, they are usually expensive and time-consuming and often provide only low recovery yields. Hence, the DSP is one major bottleneck for the commercialization of biological products. In this context, polyethylene glycol (PEG)-salt aqueous two-phase systems (ATPS) represent a promising, efficient liquid-liquid extraction technology for the DSP of various biomolecules, such as proteins and enzymes. Furthermore, ATPS can overcome the limitations of traditional DSP techniques and have gained importance for applications in several fields of biotechnology due to versatile advantages over conventional DSP methods, such as biocompatibility, technical simplicity, and easy scale-up potential. In the present review, various practical applications of PEG-salt ATPS are presented to highlight their feasibility to operate as an attractive and versatile liquid-liquid extraction technology for the DSP of proteins and enzymes, thus facilitating the approach of new researchers to this technique. Thereby, single- and multi-stage extraction, several process integration methods, as well as large-scale extraction and purification of proteins regarding technical aspects, scale-up, recycling of process chemicals, and economic aspects are discussed.

  18. Aqueous two phase system based on ionic liquid for isolation of quinine from human plasma sample.

    Science.gov (United States)

    Flieger, J; Czajkowska-Żelazko, A

    2015-01-01

    Aqueous two phase system was applied for selective extraction of quinine from human plasma. Bi-phase was constructed from ionic liquid: butyl-methyl-imidazolium chloride after addition kosmotropic salts K₃PO₄ or KH₂PO₄. Quinine was determined in plasma samples after drinking of tonic containing quinine. Determination was performed by HPLC on 5-μm Zorbax SB-CN column and eluent containing 40% acetonitrile (v/v), 20 mM phosphate buffer at pH 3 and 40 mM NaPF₆ using external standard method. The spectrophotometric detection was set λ=214 nm. Selective fluorescence detection was performed at excitation of 325 nm and emission of 375 nm. Proposed strategy provides suitable sample purification and gives extraction yields in the range of 89-106%. The determination coefficient (R(2)) has a value ≥0.997 in the range of 50-800 ng/ml quinine concentration. The limit of quantification was set at 27.9 ng/ml and the detection limit was found to be 8.4 ng/ml under fluorescence detection.

  19. Extraction of proteins with ionic liquid aqueous two-phase system based on guanidine ionic liquid.

    Science.gov (United States)

    Zeng, Qun; Wang, Yuzhi; Li, Na; Huang, Xiu; Ding, Xueqin; Lin, Xiao; Huang, Songyun; Liu, Xiaojie

    2013-11-15

    Eight kinds of green ionic liquids were synthesized, and an ionic liquid aqueous two-phase system (ILATPS) based on 1,1,3,3-tetramethylguandine acrylate (TMGA) guanidine ionic liquid was first time studied for the extraction of proteins. Single factor experiments proved that the extraction efficiency of bovine serum albumin (BSA) was influenced by the mass of IL, K2HPO4 and BSA, also related to the separation time and temperature. The optimum conditions were determined through orthogonal experiment by the five factors described above. The results showed that under the optimum conditions, the extraction efficiency could reach up to 99.6243%. The relative standard deviations (RSD) of extraction efficiencies in precision experiment, repeatability experiment and stability experiment were 0.8156% (n=5), 1.6173% (n=5) and 1.6292% (n=5), respectively. UV-vis and FT-IR spectra confirmed that there were no chemical interactions between BSA and ionic liquid in the extraction process, and the conformation of the protein was not changed after extraction. The conductivity, DLS and TEM were combined to investigate the microstructure of the top phase and the possible mechanism for the extraction. The results showed that hydrophobic interaction, hydrogen bonding interaction and the salt out effect played important roles in the transferring process, and the aggregation and embrace phenomenon was the main driving force for the separation. All these results proved that guanidine ionic liquid-based ATPSs have the potential to offer new possibility in the extraction of proteins.

  20. Aqueous Two-phase Systems with Ultrasonic Extraction Used for Extracting Phenolic Compounds from Inonotus obliquus

    Institute of Scientific and Technical Information of China (English)

    ZHAO Yan-xia; LIU Yu-bing; LIU Feng; ZHENG Wei-fa

    2013-01-01

    Objective To optimize the extracting technology of assessing the maximum yield of phenolic compounds (PC)from Inonotus obliquus by single factor experiments and orthogonal array design methods through aqueous two-phase systems combined with ultrasonic extraction.Methods The range of the independent variables,namely levels of acetone and ammonium sulfate,and ultrasonic time were identified by a first set of single factor experiments.The actual values of the independent variables coded at four levels and three factors were selected based on the results of the single factor experiments.Subsequently,the levels of acetone and ammonium sulfate,and ultrasonic time were optimized using the orthogonal array method.Results The optimum conditions for the extraction of PC were found to use 7.0 mL acetone,5.5 mg ammonium sulfate,with ultrasonic time for 5 min.Under these optimized conditions,the experimental maximum yield of PC was 37.8 mg/g,much higher than that of the traditional ultrasonic extraction (UE,29.0 mg/g).And the PC obtained by this method had stronger anti-oxidative activities than those by traditional UE method.Conclusion These results indicate the suitability of the models developed and the success in optimizing the extraction conditions.This is an economical and efficient method for extracting polyphenols from Ⅰ.obliquus.

  1. Aqueous Two-phase Systems with Ultrasonic Extraction Used for Extracting Phenolic Compounds from Inonotus obliquus

    Institute of Scientific and Technical Information of China (English)

    ZHAO; Yan-xia; LIU; Yu-bing; LIU; Feng; ZHENG; Wei-fa

    2013-01-01

    Objective To optimize the extracting technology of assessing the maximum yield of phenolic compounds (PC) from Inonotus obliquus by single factor experiments and orthogonal array design methods through aqueous two-phase systems combined with ultrasonic extraction. Methods The range of the independent variables, namely levels of acetone and ammonium sulfate, and ultrasonic time were identified by a first set of single factor experiments. The actual values of the independent variables coded at four levels and three factors were selected based on the results of the single factor experiments. Subsequently, the levels of acetone and ammonium sulfate, and ultrasonic time were optimized using the orthogonal array method. Results The optimum conditions for the extraction of PC were found to use 7.0 mL acetone, 5.5 mg ammonium sulfate, with ultrasonic time for 5 min. Under these optimized conditions, the experimental maximum yield of PC was 37.8 mg/g, much higher than that of the traditional ultrasonic extraction (UE, 29.0 mg/g). And the PC obtained by this method had stronger anti-oxidative activities than those by traditional UE method. Conclusion These results indicate the suitability of the models developed and the success in optimizing the extraction conditions. This is an economical and efficient method for extracting polyphenols from I. obliquus.

  2. Prostaglandin H synthase kinetics in the two-phase aqueous-micellar system.

    Science.gov (United States)

    Ponomareva, Olga A; Trushkin, Nikita A; Filimonov, Ivan S; Krivoshey, Alexandr V; Barkhatov, Vladimir I; Mitrofanov, Sergey I; Vrzheshch, Petr V

    2016-09-01

    Reaction mixture for PGHS (prostaglandin-H-synthase) is a two-phase system including micellar hydrophobic phase and hydrophilic aqueous phase. Reagents added to the mixture are distributed between phases, thus concentrations of reagents dissolved in phases can differ significantly from their overall contents. Using dynamic light scattering we found that the hydrophobic phase produced by tween-20 consists of micelles, which radius (4-5nm) does not depend on either tween-20 overall content (0.1%-1% v/v) or arachidonic acid (AA) addition (10-1000μM) or PGHS addition (1μM). Tween-20 overall content changing from 0.1% to 2% v/v dramatically affected COX kinetic, but accounting AA distribution between phases allowed us to estimate "true" parameters, independent of the tween-20 overall content and the concentration of another substrate: KM(Ox) equals 9.8μM O2 in the aqueous phase or 0.0074bar in the gaseous phase, KM(AA) equals 5400μM AA in the phase of tween-20 micelles and 5400/PμM AA in the aqueous phase (P is the distribution ratio for the AA between the aqueous phase and the hydrophobic phase (P≫1000)). This approach allowed to evaluate PS, the distribution ratio for the AA between the hydrophobic phase and the PGHS active center (PS ~310). This coefficient indicates the AA selectivity toward the cyclooxygenase active center.

  3. An integrated practical implementation of continuous aqueous two-phase systems for the recovery of human IgG: From the microdevice to a multistage bench-scale mixer-settler device.

    Science.gov (United States)

    Espitia-Saloma, Edith; Vâzquez-Villegas, Patricia; Rito-Palomares, Marco; Aguilar, Oscar

    2016-05-01

    Aqueous two-phase systems (ATPS) are a liquid-liquid extraction technology with clear process benefits; however, its lack of industrial embracement is still a challenge to overcome. Antibodies are a potential product to be recovered by ATPS in a commercial context. The objective of this work is to present a more integral approach of the different isolated strategies that have arisen in order to enable a practical, generic implementation of ATPS, using human immunoglobulin G (IgG) as experimental model. A microfluidic device is used for ATPS parameters preselection for product recovery. ATPS were continuously operated in a mixer-settler device in one stage, multistage and multistage with recirculation configuration. Single-stage pure IgG extraction with a polyethylene glycol (PEG) 3350-phophates ATPS within continuous operation allowed a 65% recovery. Further implementation of a multistage platform promoted a higher particle partitioning reaching a 90% recovery. The processing of IgG from a cell supernatant culture harvest in a multistage system with top phase recirculation resulted in 78% IgG recovery in bottom phase. This work conjugates three not widely spread methodologies for ATPS: microfluidics, continuous and multistage operation.

  4. Extraction of amylase from fermentation broth in poly (Ethylene Glycol salt aqueous two-phase system

    Directory of Open Access Journals (Sweden)

    Raquel Pedrosa Bezerra

    2006-07-01

    Full Text Available Studies were carried out on the partition of amylase from Bacillus subtilis in a minimal medium at 37 ºC and 110 rpm. Enzyme recovery was carried out in aqueous two-phase system PEG-Phosphate salt were carried out. The best purification factor (5.4 was obtained in system PEG 1000 (16.7% w/w with potassium phosphate (14.8% w/w, at pH 6.0, resulting in a recovery of 45.2% activity enzymatic in the salt-rich phase.Enzimas amilolíticas têm sido amplamente investigadas com a finalidade de melhorar os processos industriais para a degradação do amido. Foi determinado que a extração da enzima em sistema bifásico aquosos é um método aplicável para separação e purificação de biomoléculas em misturas. Vários sistemas compostos de soluções aquosas de polietilenoglicol e fosfato foram avaliados. Estudos de produção em meio mínimo suplementado, à 37ºC, com uma velocidade de agitação de 110rpm e recuperação da amilase a partir do Bacillus subtilis em sistema bifásico aquoso PEG-fosfato foram avaliados. O melhor fator de purificação (5.4 foi obtido no sistema PEG 1000 (16.7% w/w com fosfato de potássio (14.8% w/w, a pH 6.0, resultando na recuperação da atividade enzimática de 45.2% na fase rica em sal.

  5. Separation of curcuminoids using ionic liquid based aqueous two-phase system coupled with in situ dispersive liquid-liquid microextraction.

    Science.gov (United States)

    Shu, Yang; Gao, Mingcen; Wang, Xueying; Song, Rusheng; Lu, Jun; Chen, Xuwei

    2016-01-01

    An aqueous two-phase extraction system (ATPS) combined with an in situ dispersive liquid-liquid microextraction (DLLME) method using imidazolium ionic liquids (ILs) for the separation of curcuminoids is developed. The influence of structure of IL, the type of metathesis reagents, and the back extraction agents on the extraction efficiency is investigated. 2.0mg of curcuminoids are extracted by an IL ATPS composed of 0.4g 1,3-diethylimidazolium iodine (EeimI), 0.6g potassium hydrogen phosphate, 1.0g water. Then the bis[(trifluoromethyl)sulfonyl]imide lithium (LiNTf2) aqueous solution is added to the EeimI-rich phase of the ATPS. The water-immiscible ionic liquids, 1,3-diethylimidazole bis[(trifluoromethyl)sulfonyl]imide (EeimNTf2), forms by the metathesis reaction. The in situ DLLME is triggered simultaneously and further purifies the curcuminoids. 92% of EeimI transforms into EeimNTf2 and thus the Eeim(+) cation is used for twice in this method. Finally, 0.1mol/L NaOH aqueous solution is used as the back extraction reagent. The curcuminoids precipitate is achieved with 93% of recovery when the aqueous solution is adjusted to pH 3.0. This ATPS-DLLME method is successfully applied to the separation of curcuminoids from Curcuma Longa (0.96±0.02% of extraction yield, a purity of >51% with respect to the total dry mass of the product).

  6. Direct Purification of Pectinase from Mango (Mangifera Indica Cv. Chokanan Peel Using a PEG/Salt-Based Aqueous Two Phase System

    Directory of Open Access Journals (Sweden)

    Abdul Manap Mohd Yazid

    2011-10-01

    Full Text Available An Aqueous Two-Phase System (ATPS was employed for the first time for the separation and purification of pectinase from mango (Mangifera Indica Cv. Chokanan peel. The effects of different parameters such as molecular weight of the polymer (polyethylene glycol, 2,000–10,000, potassium phosphate composition (12–20%, w/w, system pH (6–9, and addition of different concentrations of neutral salts (0–8%, w/w on partition behavior of pectinase were investigated. The partition coefficient of the enzyme was decreased by increasing the PEG molecular weight. Additionally, the phase composition showed a significant effect on purification factor and yield of the enzyme. Optimum conditions for purification of pectinase from mango peel were achieved in a 14% PEG 4000-14% potassium phosphate system using 3% (w/w NaCl addition at pH 7.0. Based on this system, the purification factor of pectinase was increased to 13.2 with a high yield of (97.6%. Thus, this study proves that ATPS can be an inexpensive and effective method for partitioning of pectinase from mango peel.

  7. Direct purification of pectinase from mango (Mangifera Indica Cv. Chokanan) peel using a PEG/salt-based Aqueous Two Phase System.

    Science.gov (United States)

    Mehrnoush, Amid; Sarker, Md Zaidul Islam; Mustafa, Shuhaimi; Yazid, Abdul Manap Mohd

    2011-10-10

    An Aqueous Two-Phase System (ATPS) was employed for the first time for the separation and purification of pectinase from mango (Mangifera Indica Cv. Chokanan) peel. The effects of different parameters such as molecular weight of the polymer (polyethylene glycol, 2,000-10,000), potassium phosphate composition (12-20%, w/w), system pH (6-9), and addition of different concentrations of neutral salts (0-8%, w/w) on partition behavior of pectinase were investigated. The partition coefficient of the enzyme was decreased by increasing the PEG molecular weight. Additionally, the phase composition showed a significant effect on purification factor and yield of the enzyme. Optimum conditions for purification of pectinase from mango peel were achieved in a 14% PEG 4000-14% potassium phosphate system using 3% (w/w) NaCl addition at pH 7.0. Based on this system, the purification factor of pectinase was increased to 13.2 with a high yield of (97.6%). Thus, this study proves that ATPS can be an inexpensive and effective method for partitioning of pectinase from mango peel.

  8. Model description of bactrial 3-methylcatechol production in one- and two-phase systems

    NARCIS (Netherlands)

    Husken, L.E.; Hoogakker, J.; Bont, de J.A.M.; Tramper, J.; Beeftink, H.H.

    2003-01-01

    Pseudomonas putida MC2 produces 3-methylcatechol from toluene in aqueous medium. A second phase of 1-octanol may improve total product accumulation. To optimise the design of such a biphasic process, a process model was developed, both for one- and two-phase applications. The insights obtained by th

  9. Optimization of serine protease purification from mango (Mangifera indica cv. Chokanan) peel in polyethylene glycol/dextran aqueous two phase system.

    Science.gov (United States)

    Mehrnoush, Amid; Mustafa, Shuhaimi; Sarker, Md Zaidul Islam; Yazid, Abdul Manap Mohd

    2012-01-01

    Mango peel is a good source of protease but remains an industrial waste. This study focuses on the optimization of polyethylene glycol (PEG)/dextran-based aqueous two-phase system (ATPS) to purify serine protease from mango peel. The activity of serine protease in different phase systems was studied and then the possible relationship between the purification variables, namely polyethylene glycol molecular weight (PEG, 4000-12,000 g·mol(-1)), tie line length (-3.42-35.27%), NaCl (-2.5-11.5%) and pH (4.5-10.5) on the enzymatic properties of purified enzyme was investigated. The most significant effect of PEG was on the efficiency of serine protease purification. Also, there was a significant increase in the partition coefficient with the addition of 4.5% of NaCl to the system. This could be due to the high hydrophobicity of serine protease compared to protein contaminates. The optimum conditions to achieve high partition coefficient (84.2) purification factor (14.37) and yield (97.3%) of serine protease were obtained in the presence of 8000 g·mol(-1) of PEG, 17.2% of tie line length and 4.5% of NaCl at pH 7.5. The enzymatic properties of purified serine protease using PEG/dextran ATPS showed that the enzyme could be purified at a high purification factor and yield with easy scale-up and fast processing.

  10. Measurement and Correlation of Equilibrium Data for Aqueous Two-phase System Ethanol+Water+K2HPO4

    Institute of Scientific and Technical Information of China (English)

    LIN Jin-qing; TAN Ping-hua; JIN Chun-ying; LI Ming-chun

    2004-01-01

    The isothermal solubility data of aqueous two-phase system ethanol+water+K2HPO4 were determined with the turbidity titration method at 303.2 K. The binodal curves were described by using the Mistry equation very well. An experimental procedure for measuring the liquid-liquid equilibrium data of the aqueous two-phase system was proposed, in which the concentrations of the coexisting phases were determined with the corresponding densities of the solution. The tie lines were satisfactorily described by using the Othmer Tobias and Bancroft equations.

  11. Individual extraction constants of some univalent anions in the two-phase water-phenyltrifluoromethyl sulfone system.

    Science.gov (United States)

    Makrlík, Emanuel; Selucký, Pavel; Vaňura, Petr

    2011-12-01

    From extraction experiments and g-activity measurements, the extraction constants corresponding to the general equilibrium Cs+(aq) + A- (aq) Cs+(org) + A- (org) taking place in the two-phase water-phenyltrifluoromethyl sulfone (FS 13) system (A-= I-, ClO4-, MnO4-, Br-3, I-3, picrate, tetraphenylborate (BPh-4); aq = aqueous phase, org = FS 13 phase) were evaluated. Furthermore, the individual extraction constants of these 7 anions in the mentioned two-phase system were calculated; they were found to increase in the series of I-< ClO4- < Br-3 < MnO4-, picrate < I-3 < BPh-4.

  12. Extraction protease expressed by Penicillium fellutanum from the Brazilian savanna using poly(ethylene glycol)/sodium polyacrylate/NaCl aqueous two-phase system.

    Science.gov (United States)

    Barros, Kleber V G; Souza, Paula M; Cardoso, Samuel L; Borges, Leonardo L; Filho, Edivaldo X F; Junior, Adalberto P; Magalhães, Pérola O

    2015-01-01

    The partitioning of protease expressed by Penicillium fellutanum from the Brazilian savanna in a novel inexpensive and stable aqueous two-phase system (ATPS) composed of poly(ethylene glycol) (PEG) and sodium polyacrylate (NaPA) was studied in this work using factorial design. The ATPS is formed by mixing both polymers with a salt (NaCl) and fermented broth of P. fellutanum. The effects of molar mass (2,000, 4,000, and 6,000 g ⋅ mol(-1)) and concentration (6, 8, and 10 wt%) of PEG and that of NaPA concentration (6, 8, and 10 wt%) on protease partitioning (K) at 25 °C were studied. A two-level factorial design (2(3)) was implemented. The effect of Na2 SO4 concentration (5, 10, and 15 wt%) on the reextraction of the enzyme was also analyzed. The partition coefficient K ranged from 77.51 to 1.21, indicating the versatility of the method. The reextraction was achieved with the addition of 5% Na2 SO4 , allowing the partitioning of the protease to the upper phase, whereas total proteins were directed to the bottom phase. The results of partitioning using the PEG/NaPA/NaCl system and that of the subsequent reextraction with Na2 SO4 suggest that this method can be used to purify proteases from fermented broth of P. fellutanum.

  13. Two-phase experimental heat transfer studies on a water-diesel system in a shell and tube heat exchanger

    Directory of Open Access Journals (Sweden)

    V. Alagesan

    2012-06-01

    Full Text Available Two-phase heat transfer involving two immiscible systems is gaining importance in petrochemical and allied industries. Varying compositions of diesel and water were experimentally studied in a 1:2 shell and tube heat exchanger. The data on pure water and diesel were fitted to an equation of the form. h1φ = a NmRe.The two-phase multiplier, Φ L, was related to the Lockhart Martinelli (L-M parameter, χtt², using the two-phase data and a correlation Φ L = b+c(χtt²+d/(χtt²² was established. The two-phase heat transfer coefficient was calculated based on the coefficients 'a' and 'm' for pure diesel and pure water along with ФL and the L-M parameter. The calculated values of the two-phase heat transfer coefficient h2φ based on pure diesel and pure water suggest that diesel is a better reference fluid since the average error is much smaller compared to pure water as reference.

  14. A numerical method for a model of two-phase flow in a coupled free flow and porous media system

    KAUST Repository

    Chen, Jie

    2014-07-01

    In this article, we study two-phase fluid flow in coupled free flow and porous media regions. The model consists of coupled Cahn-Hilliard and Navier-Stokes equations in the free fluid region and the two-phase Darcy law in the porous medium region. We propose a Robin-Robin domain decomposition method for the coupled Navier-Stokes and Darcy system with the generalized Beavers-Joseph-Saffman condition on the interface between the free flow and the porous media regions. Numerical examples are presented to illustrate the effectiveness of this method. © 2014 Elsevier Inc.

  15. A simple method to optimize the HSCCC two-phase solvent system by predicting the partition coefficient for target compound.

    Science.gov (United States)

    Han, Quan-Bin; Wong, Lina; Yang, Nian-Yun; Song, Jing-Zheng; Qiao, Chun-Feng; Yiu, Hillary; Ito, Yoichiro; Xu, Hong-Xi

    2008-04-01

    A simple method was developed to optimize the solvent ratio of the two-phase solvent system used in the high-speed counter-current chromatography (HSCCC) separation. Some mathematic equations, such as the exponential and the power equations, were established to describe the relationship between the solvent ratio and the partition coefficient. Using this new method, the two-phase solvent system was easily optimized to obtain a proper partition coefficient for the CCC separation of the target compound. Furthermore, this method was satisfactorily applied in determining the two-phase solvent system for the HSCCC preparation of pseudolaric acid B from the Chinese herb Pseudolarix kaempferi Gordon (Pinaceae). The two-phase solvent system of n-hexane/EtOAc/MeOH/H(2)O (5:5:5:5 by volume) was used with a good partition coefficient K = 1.08. As a result, 232.05 mg of pseudolaric acid B was yielded from 0.5 g of the crude extract with a purity of 97.26% by HPLC analysis.

  16. Ionic interaction of oral streptococcal bacteria studied by partition in an aqueous polymer two-phase system.

    Science.gov (United States)

    Westergren, G

    1981-01-01

    The net surface charge of various oral streptococci were assessed by aqueous two-phase partitioning in a dextran-polyethylene glycol system. Great variability was found among individual strains within all species tested. Type 1 strains of Streptococcus sanguis serotypes which have been found to be more adherent, exposed a lower negative net surface charge than Type 2 strains.

  17. Two-phase plate-fin heat exchanger modeling for waste heat recovery systems in diesel engines

    NARCIS (Netherlands)

    Feru, E.; de Jager, B.; Willems, F.; Steinbuch, M.

    2014-01-01

    This paper presents the modeling and model validation for a modular two-phase heat exchanger that recovers energy in heavy-duty diesel engines. The model is developed for temperature and vapor quality prediction and for control design of the waste heat recovery system. In the studied waste heat reco

  18. Use of multifactorial analysis to develop aqueous two-phase systems for isolation of non-native IGF-I.

    Science.gov (United States)

    Hart, R A; Ogez, J R; Builder, S E

    1995-04-01

    A high yield procedure was developed to solubilize and extract IGF-I from recombinant E. coli by adding chaotrope and disulfide reductant to alkaline fermentation broth. To enhance centrifugation performance and recovery yield, a salt/polymer aqueous two-phase extraction procedure was developed whereby soluble non-native IGF-I and biomass solids are enriched in separate liquid phases. To develop this extraction system a multifactorial experimental approach was used to simultaneously map the phase diagram and identify conditions to suitably partition IGF-I and cell remnants. The presence of urea in these systems tended to disrupt two-phase formation and solids sedimentation. This, in turn, constrained the concentrations of phase forming solutes which could be effectively used. Systems containing low levels of salt (less than about 4% w/w) and polymer (less than about 10% w/w) did not form two phases. Systems containing high levels of salt (greater than about 7% w/w) and polymer (greater than about 18% w/w) formed two phases with floating solids. Intermediate levels of salt (between about 4% and 7% w/w) and polymer (between about 10% and 18% w/w) formed two phases in which solids were enriched in the heavy phase. Systems in this latter desired category were produced with a variety of different salts and polymers and all enriched non-native IGF-I in the light phase. Highest recovery yield (about 90%) was obtained with systems composed of 5% sodium sulfate and 14% PEG-8000.(ABSTRACT TRUNCATED AT 250 WORDS)

  19. [Isolation and purification of alpha-glycerophosphate oxidase in a polyethylene glycol/(NH4 )2SO4 aqueous two-phase system].

    Science.gov (United States)

    Meng, Yao; Jin, Jiagui; Liu, Shuangfeng; Yang, Min; Zhang, Qinglian; Wan, Li; Tang, Kun

    2014-02-01

    Alpha-glycerophosphate oxidase (alpha-GPO) from Enterococcus casseli flavus was successfully isolated and purified by using polyethylene glycol (PEG)/(NH4)2SO4 aqueous two-phase system (ATPS). The results showed that the chosen PEG/(NH4)2SO4 ATPS could be affected by PEG molecular weight, pH, concentration of PEG and (NH4)2SO4, and inorganic salt as well as additional amount of crude enzyme. After evaluating these influencing factors, the final optimum purification strategy was formed by 16.5% (m/m) PEG2000, 13.2% (m/m) (NH4)2SO4, pH 7.5 and 30% (m/m) additive crude enzyme, respectively. The NaCl was a negative influencing factor which would lead to lower purification fold and activity recovery. These conditions eventually resulted in the activity recovery of 89% (m/m), distribution coefficient of 1.2 and purification fold of 7.0.

  20. Ionic liquid-based ultrasound-assisted extraction and aqueous two-phase system for analysis of caffeoylquinic acids from Flos Lonicerae Japonicae.

    Science.gov (United States)

    Tan, Ting; Lai, Chang-Jiang-Sheng; OuYang, Hui; He, Ming-Zhen; Feng, Yulin

    2016-02-20

    In this work, an ionic liquid-based ultrasonic-assisted extraction (ILUAE) method was developed to extract caffeoylquinic acids (CQAs) from Flos Lonicerae Japonicae (FLJ). ILUAE parameters were optimized by response surface methodology, including IL concentration, ultrasonic time, and liquid-solid ratio. Optimized ILUAE approach gained the highest extraction yields of 28.53, 18.21, 3.84mg/g for 3-O-caffeoylquinic acid (C1), 3,5-di-O-caffeoylquinic acid (C2), 3,4-di-O-caffeoylquinic acid (C3), respectively. C1-C3 are the three most abundant CQAs compounds in FLJ. The method showed comparable extraction yield and shorter extraction time compared with conventional extraction techniques. Subsequently, an aqueous two-phase system (ATPS) was applied in extraction solutions. Two trace CQAs, 5-O-caffeoylquinic acid (C4) and 4,5-di-O-caffeoylquinic acid (C5), were significantly enriched with signal to noise values increasing from less than 10 to higher than 1475. The results indicated that ILUAE and ATPS are efficient and environmentally-friendly sample extraction and enrichment techniques for CQAs from herbal medicines.

  1. Cloud Point and Liquid-Liquid Equilibrium Behavior of Thermosensitive Polymer L61 and Salt Aqueous Two-Phase System.

    Science.gov (United States)

    Rao, Wenwei; Wang, Yun; Han, Juan; Wang, Lei; Chen, Tong; Liu, Yan; Ni, Liang

    2015-06-25

    The cloud point of thermosensitive triblock polymer L61, poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO), was determined in the presence of various electrolytes (K2HPO4, (NH4)3C6H5O7, and K3C6H5O7). The cloud point of L61 was lowered by the addition of electrolytes, and the cloud point of L61 decreased linearly with increasing electrolyte concentration. The efficacy of electrolytes on reducing cloud point followed the order: K3C6H5O7 > (NH4)3C6H5O7 > K2HPO4. With the increase in salt concentration, aqueous two-phase systems exhibited a phase inversion. In addition, increasing the temperature reduced the concentration of salt needed that could promote phase inversion. The phase diagrams and liquid-liquid equilibrium data of the L61-K2HPO4/(NH4)3C6H5O7/K3C6H5O7 aqueous two-phase systems (before the phase inversion but also after phase inversion) were determined at T = (25, 30, and 35) °C. Phase diagrams of aqueous two-phase systems were fitted to a four-parameter empirical nonlinear expression. Moreover, the slopes of the tie-lines and the area of two-phase region in the diagram have a tendency to rise with increasing temperature. The capacity of different salts to induce aqueous two-phase system formation was the same order as the ability of salts to reduce the cloud point.

  2. Two-phase Flow of Liquid-gas in Diesel Fuel Injection System and Their Effect on Engine Performances

    Institute of Scientific and Technical Information of China (English)

    Yongling He; Zhihe Zhao; Jianxin Liu; Huiyong Du; Min Li; Yongping Zong

    2001-01-01

    In this paper, by using high-speed camera, CCD camera, signal and graph acquisition system, and other experimental instruments, investigation on liquid-gas two-phase flow in diesel fuel injection system and their effect on engine performances were made. Emerging and bursting of cavitation in the cavity above pump delivery valve, in injection pipe, and in fuel trough of injector of the fuel injection system were observed and mechanism of cavitation were discussed. Effects of liquid-gas two-phase flow on propagation velocity of pressure wave of the system and on irregular injection were analyzed. Two types of cavitation, long living time cavitation and short living time cavitation, in the cavity above pump delivery valve of diesel fuel injection system were observed.

  3. Two-phase flows and heat transfer within systems with ambient pressure above the thermodynamic critical pressure

    Science.gov (United States)

    Hendricks, R. C.; Braun, M. J.; Mullen, R. L.

    1986-01-01

    In systems where the design inlet and outlet pressure P sub amb are maintained above the thermodynamic critical pressure P sub c, it is often assumed that heat and mass transfer are governed by single-phase relations and that two-phase flows cannot occur. This simple rule of thumb is adequate in many low-power designs but is inadequate for high-performance turbomachines, boilers, and other systems where two-phase regions can exist even though P sub amb P sub c. Heat and mass transfer and rotordynamic-fluid-mechanic restoring forces depend on momentum differences, and those for a two-phase zone can differ significantly from those for a single-phase zone. By using a laminar, variable-property bearing code and a rotating boiler code, pressure and temperature surfaces were determined that illustrate nesting of a two-phase region within a supercritical pressure region. The method of corresponding states is applied to bearings with reasonable rapport.

  4. Low Energy Consumption Technique for Processing Rapeseed with Two-phase Extraction System without Ammonia

    Institute of Scientific and Technical Information of China (English)

    Shi Meiren; Qin Jinping; SQian Renyuan

    2000-01-01

    the mother liquid of methanol phase obtained from rapeseed two-phase extraction process can directly be reused in large amounts to process rapeseed again together with some fresh methanol phase, so long as it is treated with a litter of proper additives in advance. The ratio of the reused mother liquid may be more than 3/ 4 of the total amount of the methanol phase needed for processing rapeseed, so the energy consumption can be decreased tremendously. The meal obtained by use of the reused mother liquid keeps the quality as good as those obtained by use of totally fresh methanol phase with light color, weak taste, crispness, good palatability, high protein content, and a low level of glucosinolates much more less than that stipulated by the State for the fodder of grade A.

  5. Facile synthesis and properties of CdSe quantum dots in a novel two-phase liquid/liquid system

    Science.gov (United States)

    Wang, Jidong; Wang, Xiaoyu; Tang, Hengshan; Gao, Zehua; He, Shengquan; Ke, Dandan; Zheng, Yue; Han, Shumin

    2017-10-01

    High-quantity CdSe QDs were synthesized in a novel two-phase liquid/liquid system. This system, ODE/water was stable and as-used solvents were almost nontoxic. The methodology leading to the successful synthesis of CdSe QDs was a typical, one-pot approach and the obtained CdSe QDs with zinc-blende phase structure exhibited excellent optical properties, narrow size distribution, higher particle uniformity and crystallinity. The mechanism of nucleation and growth of CdSe QDs were discussed by the possible thermodynamic equilibrium existing in ODE/water interface. This two-phase liquid/liquid system would broaden the synthesis of other semiconductor QDs.

  6. Study on PEG-(NH4)2SO4 Aqueous Two-Phase System and Distribution Behavior of Drugs

    Institute of Scientific and Technical Information of China (English)

    LI, Lei(李蕾); HE, Chi-Yang(何池洋); LI, She-Hong(李社红); LIU, Feng(刘锋); SU, Shun(苏顺); KONG, Xiang-Xu(孔祥旭); LI, Na(李娜); LI, Ke-An(李克安)

    2004-01-01

    The distribution behavior of chlorpromazine hydrochloride (CPZ), procaine hydrochloride (PCN) and procaine amide hydrochloride (PCNA) in polyethylene glycol (PEG800 or PEG1500)-(NH4)2SO4 aqueous two-phase systems has been investigated. The result shows that the PEG-(NH4)2SO4 aqueous two-phase system has potential extraction capability in small molecular drug separation. In PEG800-(NH4)2SO4 system, the extraction efficiencies (E)of CPZ, PCN and PCNA amount to 92.8%, 74.5% and 74.4%, respectively, with the distribution coefficients (KD)being 25.7, 5.9 and 5.8, correspondingly. In PEG1500-(NH4)2SO4 system, the extraction efficiencies (E) of CPZ,PCN and PCNA are 93.7%, 71.3% and 63.2%, respectively, with distribution coefficients (KD) of 39.6, 6.6 and 5.0,correspondingly. Based on the study on ultraviolet and fluorescence spectra and also distribution behavior of the drugs in PEG-(NH4)2SO4 aqueous two-phase system, extraction mechanism was further proposed that both hydrogen bond and hydrophobic interaction are involved in extraction.

  7. Recyclable hydroformylation catalysts of higher alkenes using immobilized catalysts and two-phase systems

    Energy Technology Data Exchange (ETDEWEB)

    Reek, J.N.H.; Sandee, A.J.; Schreuder Goedheijt, M.; Kamer, P.C.J.; Leeuwen, P.W.N.M. van [Amsterdam Univ. (Netherlands). Inst. of Molecular Chemistry, Homogeneous Catalysis

    2001-03-01

    This article reports on the use of recyclable catalysts, using different concepts, in the hydroformylation of 1-octene employing diphosphine ligands based on the xantene backbone. Amphiphilic diphosphines were developed for the aqueous two-phase catalysis, which spontaneously form aggregates that are remarkably thermostable. The observed TOF's in the hydroformylation of 1-octene using ligands that form vesicles are up to 14 times higher compared to analogue ligands that do not form aggregates. A water-soluble ligand based on the xantene backbone was used to form a stable and recyclable supported aqueous phase catalyst (SAPC). A xanthene-based ligand, N-(3-trimethoxysilane-n-propyl)-4,5-bis(diphenyl-phosphino)-phenoxazine (Siloxantphos) was anchored covalently to a silica support by the sol-gel technique. All concepts demonstrated that the rhodium complexes of these ligands form very selective hydroformylation catalysts producing linear aldehydes. Under similar conditions the activity of the silica-immobilized catalysts is higher than that of the aggregates (by a factor 2) of which the activity is higher than the SAP catalyst (factor 12). (orig.)

  8. Quantitative study on experimentally observed poroelastic behavior of Berea sandstone in two-phase fluid system

    Science.gov (United States)

    Goto, Hiroki; Aichi, Masaatsu; Tokunaga, Tomochika; Yamamoto, Hajime; Ogawa, Toyokazu; Aoki, Tomoyuki

    2014-08-01

    Coupled two-phase fluid flow and poroelastic deformation of Berea sandstone is studied through laboratory experiment and numerical simulation. In the experiment, compressed air was infiltrated from the bottom of a water-saturated cylindrical Berea sandstone sample under hydrostatic external stress condition. Both axial and circumferential strains at half the height of the sample showed sudden extension and monotonic and gradual extension afterward. Numerical simulation based on thermodynamically consistent constitutive equations was conducted in order to quantitatively analyze the experimental results. In a simulation assuming isotropy of material properties, the volumetric discharge rate of water at the outlet and one of the axial, circumferential, and volumetric strains at half the height of the sample were reproduced well by each parameter set, while the other two strains were not. When introducing transverse isotropy, all the experimental data were reproduced well. In addition, the effect of saturation dependency of Bishop's effective stress coefficient on the deformation behavior of porous media was discussed, and it was found that strains, both axial and circumferential, are sensitive to the coefficient.

  9. Transformation of Geniposide into Genipin by Immobilized β-Glucosidase in a Two-Phase Aqueous-Organic System

    Directory of Open Access Journals (Sweden)

    Duo Jin

    2011-05-01

    Full Text Available Genipin is the bioactive compound of geniposide and a natural cross-linking agent. In order to improve the preparation process of genipin, the hydrolysis of geniposide to genipin by immobilized β-glucosidase in an aqueous-organic two-phase system was studied. β-Glucosidase was immobilized by the crosslinking-embedding method using sodium alginate as the carrier. The optimum reaction temperature, pH value and time were 55 °C, 4.5 and 2.5 h, respectively. To reduce genipin hydrolysis and byproduct production the reaction was carried out in an aqueous-organic two-phase system comprising ethyl acetate and sodium acetate buffer. The product was analyzed by HPLC, UV, IR, and NMR. The yield of genipin was 47.81% and its purity was over 98% (HPLC.

  10. Aqueous two-phase extraction of 2,3-butanediol from fermentation broths by isopropanol/ammonium sulfate system.

    Science.gov (United States)

    Sun, Li-Hui; Jiang, Bo; Xiu, Zhi-Long

    2009-03-01

    A novel aqueous two-phase system consisted of 2-propanol/ammonium sulfate was used for the extraction of 2,3-butanediol from fermentation broths. The maximum partition coefficient and recovery of 2,3-butanediol reached 9.9 and 93.7%, respectively, and more than 99% of the cells and about 85% of the soluble proteins were removed when 34% (w/w) 2-propanol and 20% (w/w) ammonium sulfate were used. The separated cells could be re-used as inocula for subsequent fermentations. The aqueous two-phase system described in this study may have potential application in the extraction of 2,3-butanediol produced by industrial fermentation processes.

  11. Optimized Enzymatic Synthesis of Hesperidin Fatty Acid Esters in a Two-Phase System Containing Ionic Liquid

    Directory of Open Access Journals (Sweden)

    Yollanda Edwirges Moreira Franco

    2011-08-01

    Full Text Available Response surface methodology (RSM based on a five-level, three-variable central composite design (CCD was employed for modeling and optimizing the conversion yield of the enzymatic acylation of hesperidin with decanoic acid using immobilized Candida antarctica lipase B (CALB in a two-phase system containing [bmim]BF4. The three variables studied (molar ratio of hesperidin to decanoic acid, [bmim]BF4/acetone ratio and lipase concentration significantly affected the conversion yield of acylated hesperidin derivative. Verification experiments confirmed the validity of the predicted model. The lipase showed higher conversion degree in a two-phase system using [bmim]BF4 and acetone compared to that in pure acetone. Under the optimal reaction conditions carried out in a single-step biocatalytic process when the water content was kept lower than 200 ppm, the maximum acylation yield was 53.6%.

  12. Application of surface response analysis to the optimization of penicillin acylase purification in aqueous two-phase systems

    OpenAIRE

    2002-01-01

    Penicillin acylase purification from an Escherichia coli crude extract using PEG 3350 – sodium citrate aqueous two phase systems was optimized. An experimental design was used to evaluate the influence of PEG, sodium citrate and sodium chloride on the purification parameters. A central composite design was defined centred on the previously found conditions for highest purification from an osmotic shock extract. Mathematical models for the partition coefficient of protein and enzyme, balance o...

  13. Two-phase (acidogenic-methanogenic) anaerobic thermophilic/mesophilic digestion system for producing Class A biosolids from municipal sludge.

    Science.gov (United States)

    Rubio-Loza, L A; Noyola, A

    2010-01-01

    Two different arrangements of two-phase anaerobic sludge systems were operated treating a mixture of primary and secondary sludge. Two steady state periods were evaluated: the first acidogenic thermophilic phase was operated at hydraulic retention times of 3 and 2 days and the second methanogenic (mesophilic and thermophilic) phases at 13 and 10 days. The two-phase systems had an efficient removal of pathogens and parasites, achieving values lower than those specified for Class A biosolids, according to the Mexican Standard NOM-004-SEMARNAT-2002. The first thermophilic phase achieved almost complete destruction of pathogens and parasites by itself. During the second steady state period, volatile fatty acids accumulated in the second methanogenic phases (HRT of 10 days and an organic load of 3 kg VS/m(3)d) indicating that the systems were overloaded, mainly the mesophilic digester. In this case, the accumulation of propionic acid may be related to a deficiency of micronutrients. The results show that the two-phase thermophilic/mesophilic anaerobic sludge digestion may be considered as an adequate option for the production of Class A biosolids.

  14. Production of dry Lactobacillus rhamnosus GG preparations by spray drying and lyophilization in aqueous two-phase systems

    Directory of Open Access Journals (Sweden)

    Katarzyna Leja

    2009-12-01

    Full Text Available Background. Drying is the oldest method of food preservation. It works by removing water from the food, which prevents the growth of microorganisms and decay. Moreover, spray or freeze drying is also used for the preservation of probiotic cultures. The aim of this study was to compare a survival rate of probiotic bacteria Lactobacillus rhamnosus during spray and freeze drying in ATPS. These results were also compared with survival rate of cells dried under the same conditions but suspended only in skim milk, 6% solution of PVP or 6% solution of dextran. Material and methods. The bacteria Lactobacillus rhamnosus GGwere suspended and spray or freeze dried in various types of aqueous two-phase emulsions: PVP/dextran, PEG4000/dextran and PEG8000/dextran. These emulsions consisted of different types of polymers and had varying ratio of polymers in dispersed (dextran and dispersing (PEG and PVP phases. Results. The research demonstrated that survival rate of bacteria directly after drying depended mainly on protective reagent, rather than on drying method. After 30-day-storage of the dried bacteria cell specimens, the highest survival rate was noted in case of freeze dried cells in milk. In case of spray drying the highest cell survival rate was observed when emulsion PVP3.6%/dextran2.4% was used as a drying medium. Conclusions. Finally, it has been found that cell survival rate was not strongly influenced by the storage temperature of the powder but it depended on the drying medium.  

  15. Optimization of Serine Protease Purification from Mango (Mangifera indica cv. Chokanan Peel in Polyethylene Glycol/Dextran Aqueous Two Phase System

    Directory of Open Access Journals (Sweden)

    Abdul Manap Mohd Yazid

    2012-03-01

    Full Text Available Mango peel is a good source of protease but remains an industrial waste. This study focuses on the optimization of polyethylene glycol (PEG/dextran-based aqueous two-phase system (ATPS to purify serine protease from mango peel. The activity of serine protease in different phase systems was studied and then the possible relationship between the purification variables, namely polyethylene glycol molecular weight (PEG, 4000–12,000 g·mol−1, tie line length (−3.42–35.27%, NaCl (−2.5–11.5% and pH (4.5–10.5 on the enzymatic properties of purified enzyme was investigated. The most significant effect of PEG was on the efficiency of serine protease purification. Also, there was a significant increase in the partition coefficient with the addition of 4.5% of NaCl to the system. This could be due to the high hydrophobicity of serine protease compared to protein contaminates. The optimum conditions to achieve high partition coefficient (84.2 purification factor (14.37 and yield (97.3% of serine protease were obtained in the presence of 8000 g·mol−1 of PEG, 17.2% of tie line length and 4.5% of NaCl at pH 7.5. The enzymatic properties of purified serine protease using PEG/dextran ATPS showed that the enzyme could be purified at a high purification factor and yield with easy scale-up and fast processing.

  16. Effect of Mechanical Stress on Magnetic States and Hysteresis Characteristics of a Two-Phase Nanoparticles System

    Directory of Open Access Journals (Sweden)

    Leonid Lazarevich Afremov

    2013-01-01

    Full Text Available In terms of the two-phase nanoparticles model, the effect of mechanical stress on the magnetic state of both uniaxial and multiaxial heterophase magnetic is investigated. The spectrum of critical fields of reversal of phases' magnetic moments was calculated and phase diagrams were drawn to assess the effect of mechanical stress on the degree of metastability of two-phase nanoparticles' magnetic states. By the example of epitaxial cobalt-coated -Fe2O3 particles, a theoretical analysis of the effect of uniaxial mechanical stress on the magnetization of a system of noninteracting heterophase nanoparticles is investigated. It was shown that tension reduced and compression increased coercive force , while the residual saturation magnetization was not changed under the influence of mechanical stress.

  17. (Liquid + liquid) and (liquid + solid) equilibrium of aqueous two-phase systems containing poly ethylene glycol di-methyl ether 2000 and di-sodium hydrogen phosphate

    Energy Technology Data Exchange (ETDEWEB)

    Zafarani-Moattar, Mohammed Taghi, E-mail: zafarani47@yahoo.co [Physical Chemistry Department, University of Tabriz, Tabriz 51664 (Iran, Islamic Republic of); Nasiri, Saeed [Physical Chemistry Department, University of Tabriz, Tabriz 51664 (Iran, Islamic Republic of)

    2010-09-15

    (Liquid + liquid) equilibrium (LLE) for the {l_brace}poly ethylene glycol di-methyl ether 2000 (PEGDME{sub 2000}) + Na{sub 2}HPO{sub 4} + H{sub 2}O{r_brace} system have been determined experimentally at T = (298.15, 308.15, 313.15, and 318.15) K. The effects of temperature on the binodals and tie-lines for the investigated aqueous two-phase system (ATPS) have been studied. An empirical non-linear expression developed by Merchuk was used for reproducing the experimental binodal data. In this work, the three fitting parameters of the Merchuk equation were obtained with the temperature dependence expressed in the linear form with (T - T{sub 0}) K as a variable. Furthermore, the modified local composition segment-based NRTL and Wilson models and also osmotic virial equation were used to describe the LLE data of the studied system. Also, the effects of the type of salt on LLE are discussed. In addition, the effects of end groups of the polymers PEGDME{sub 2000} and poly ethylene glycol 2000 on phase forming ability were studied. The complete phase diagram for the poly ethylene {l_brace}glycol di-methyl ether 2000 (PEGDME{sub 2000}) + Na{sub 2}HPO{sub 4} + H{sub 2}O{r_brace} system has also been determined at T = 298.15 K.

  18. Recovery of lignin peroxidase from submerged liquid fermentation of Amauroderma rugosum (Blume & T. Nees) Torrend using polyethylene glycol/salt aqueous two-phase system.

    Science.gov (United States)

    Jong, Wan Yng Linda; Show, Pau Loke; Ling, Tau Chuan; Tan, Yee Shin

    2017-07-01

    Amauroderma rugosum is a wild mushroom species widely distributed in tropics and is classified under the class of Basidiomycetes. Basidiomycetes are well-known for their abilities of producing lignocellulolytic enzymes such as lignin peroxidase (LiP), laccase (Lac) and manganese peroxidase (MnP). Different factors such as nutrient sources, incubation period and agitation affect the production of lignocellulolytic enzymes. The A. rugosum produced LiP in the medium supplemented with potato dextrose broth (PDB), 0.5% yeast and 1.0% saw dust at 26.70±3.31 U/mL. However, the LiP activity was increased to 106.32±5.32 U/mL when supplemented with 150 μm of copper (CuSO4). The aqueous two-phase system (ATPS) is a simple, rapid and low cost method for primary extraction and recovery of LiP. A total of 25 systems made from five different molecular weights of polyethylene glycol (PEG)/dipotassium hydrogen phosphate (K2HPO4) were tested. PEG 600 produced the highest top phase purification factor (PFT) of 1.33±0.62 with yield of 72.18±8.50%. The optimization of the ATPS parameters, such as volume ratio VR, pH and crude enzyme loading are the factors controlling the phase partition. Our results showed that significant improvement (PFT of 6.26±2.87 with yield of 87.31±3.14%) of LiP recovery can be achieved by optimized the parameters. Copyright © 2017 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

  19. Optimization of ultrasound-assisted aqueous two-phase system extraction of polyphenolic compounds from Aronia melanocarpa pomace by response surface methodology.

    Science.gov (United States)

    Xu, Yan-Yang; Qiu, Yang; Ren, Hui; Ju, Dong-Hu; Jia, Hong-Lei

    2017-03-16

    Aronia melanocarpa berries are abundant in polyphenolic compounds. After juice production, the pomace of pressed berries still contains a substantial amount of polyphenolic compounds. For efficient utilization of A. melanocarpa berries and the enhancement of polyphenolic compound yields in Aronia melanocarpa pomace (AMP), total phenolics (TP) and total flavonoids (TF) from AMP were extracted, using ultrasound-assisted aqueous two-phase system (UAE-ATPS) extraction method. First, the influences of ammonium sulfate concentration, ethanol-water ratio, ultrasonic time, and ultrasonic power on TP and TF yields were investigated. On this basis, process variables such as ammonium sulfate concentration (0.30-0.35 g mL(-1)), ethanol-water ratio (0.6-0.8), ultrasonic time (40-60 min), and ultrasonic power (175-225 W) were further optimized by implementing Box-Benhnken design with response surface methodology. The experimental results showed that optimal extraction conditions of TP from AMP were as follows: ammonium sulfate concentration of 0.324 g mL(-1), ethanol-water ratio of 0.69, ultrasonic time of 52 min, and ultrasonic power of 200 W. Meanwhile, ammonium sulfate concentration of 0.320 g mL(-1), ethanol-water ratio of 0.71, ultrasonic time of 50 min, and ultrasonic power of 200 W were determined as optimum extraction conditions of TF in AMP. Experimental validation was performed, where TP and TF yields reached 68.15 ± 1.04 and 11.67 ± 0.63 mg g(-1), respectively. Close agreement was found between experimental and predicted values. Overall, the present results demonstrated that ultrasound-assisted aqueous two-phase system extraction method was successfully used to extract total phenolics and flavonoids in A. melanocarpa pomace.

  20. Efficient hydrolysis of tuna oil by a surfactant-coated lipase in a two-phase system.

    Science.gov (United States)

    Ko, Wen-Ching; Wang, Hsiu-Ju; Hwang, Jyh-Sheng; Hsieh, Chang-Wei

    2006-03-08

    A surfactant-coated lipase (SCL) prepared by mixing Candida rugosa lipase with emulsifier in ethanol was used to hydrolyze tuna oil in a two-phase aqueous-organic system. Both enzyme (SCL) and substrate (tuna oil) were soluble in the organic phase, and the hydrolysis could occur with water molecules from the aqueous phase. This hydrolysis could promptly proceed compared to that catalyzed by native lipases which only occurred at the interface between the two phases. Michaelis-Menten kinetics in the two-phase reactions showed that the K(m) value of the SCL was half that of the native lipase, while the maximum velocity (V(max)) was 11.5 times higher. The hydrolysis method resulted in enrichment of n-3 polyunsaturated fatty acid (n-3 PUFA) content in glyceride mixtures from 26.4% to 49.8% and DHA from 19.1% to 38.9%. The SCL acted as an efficient hydrolytic catalyst for tuna oil.

  1. Enzymatic hydrolysis of cellulose in aqueous two-phase systems. 1. Partition of cellulases from Trichoderma reesei

    Energy Technology Data Exchange (ETDEWEB)

    Tjerneld, F.; Persson, J.; Albertsson, P.A.; Hahn-Haegerdal, B.

    1985-07-01

    The partitioning of endo-..beta..-glucanase, exo-..beta..-glucananse, and ..beta..-glucosidase from Trichoderma reesei QM 9414 in aqueous two-phase systems has been studied with the object of designing a phase system for continuous bioconversion of cellulose. The partitioning of the enzymes in two-phase systems composed of various water soluble polymeric compounds were studied. Systems based on dextran and polyethylene glycol (PEG) were optimal for one sidedly partitioning of the enzymes to the bottom phase. The influence of polymer molecular weights, polymer concentration, ionic composition of the medium, pH, temperature, and adsorption of the enzymes to cellulose on the enyzme partition coefficients (K) were studied. By combining the effects of polymer molecular weight and adsorption to cellulose, K values could be reduced for endo-..beta..-glucanase to 0.02 and for ..beta..-glucosidase to 0.005 at 20 degrees C in a phase system of Dvalues could be reduced for endo-..beta..-glucanase to 0.02 and for ..beta..-glucosidase to 0.005 at 20 degrees C in a phase system of Dextran 40-PEG 40000 in the presence of excess cellulose. At 50 degrees C, K values were increased by a factor of two. In a phase system based on inexpensive crude dextran and PEG, the partition coefficient for endo-..beta..-glucanase was 0.16 and for beta-glucosidase was 0.14 at 20 degrees C with excess cellulose present.

  2. Slug flow transitions in horizontal gas/liquid two-phase flows. Dependence on channel height and system pressure for air/water and steam/water two-phase flows

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, Hideo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1996-05-01

    The slug flow transitions and related phenomena for horizontal two-phase flows were studied for a better prediction of two-phase flows that typically appear during the reactor loss-of-coolant accidents (LOCAs). For better representation of the flow conditions experimentally, two large-scaled facility: TPTF for high-pressure steam/water two-phase flows and large duct test facility for air/water two-phase flows, were used. The visual observation of the flow using a video-probe was performed in the TPTF experiments for good understanding of the phenomena. The currently-used models and correlations based mostly on the small-scale low-pressure experiments were reviewed and improved based on these experimental results. The modified Taitel-Dukler model for prediction of transition into slug flow from wavy flow and the modified Steen-Wallis correlation for prediction of onset of liquid entrainment from the interfacial waves were obtained. An empirical correlation for the gas-liquid interfacial friction factor was obtained further for prediction of liquid levels at wavy flow. The region of slug flow regime that is generally under influences of the channel height and system pressure was predicted well when these models and correlations were applied together. (author). 90 refs.

  3. Online damage inspection of optics for ATP system

    Science.gov (United States)

    Chen, Jing; Jiang, Yu; Mao, Yao; Gan, Xun; Liu, Qiong

    2016-09-01

    In the Electro-Optical acquisition-tracking-pointing system (ATP), the optical components will be damaged with the several influencing factors. In this situation, the rate will increase sharply when the arrival of damage to some extent. As the complex processing techniques and long processing cycle of optical components, the damage will cause the great increase of the system development cost and cycle. Therefore, it is significant to detect the laser-induced damage in the ATP system. At present, the major research on the on-line damage detection technology of optical components is for the large optical system in the international. The relevant detection systems have complicated structures and many of components, and require enough installation space reserved, which do not apply for ATP system. To solve the problem mentioned before, This paper use a method based on machine vision to detect the damage on-line for the present ATP system. To start with, CCD and PC are used for image acquisition. Secondly, smoothing filters are used to restrain false damage points produced by noise. Then, with the shape feature included in the damage image, the OTSU Method which can define the best segmentation threshold automatically is used to achieve the goal to locate the damage regions. At last, we can supply some opinions for the lifetime of the optical components by analyzing the damage data, such as damage area, damage position. The method has the characteristics of few-detectors and simple-structures which can be installed without any changes of the original light path. With the method, experimental results show that it is stable and effective to achieve the goal of detecting the damage of optical components on-line in the ATP system.

  4. Modeling Two-Phase Flow and Vapor Cycles Using the Generalized Fluid System Simulation Program

    Science.gov (United States)

    Smith, Amanda D.; Majumdar, Alok K.

    2017-01-01

    This work presents three new applications for the general purpose fluid network solver code GFSSP developed at NASA's Marshall Space Flight Center: (1) cooling tower, (2) vapor-compression refrigeration system, and (3) vapor-expansion power generation system. These systems are widely used across engineering disciplines in a variety of energy systems, and these models expand the capabilities and the use of GFSSP to include fluids and features that are not part of its present set of provided examples. GFSSP provides pressure, temperature, and species concentrations at designated locations, or nodes, within a fluid network based on a finite volume formulation of thermodynamics and conservation laws. This paper describes the theoretical basis for the construction of the models, their implementation in the current GFSSP modeling system, and a brief evaluation of the usefulness of the model results, as well as their applicability toward a broader spectrum of analytical problems in both university teaching and engineering research.

  5. ATP-Binding Cassette Systems of Brucella

    Directory of Open Access Journals (Sweden)

    Dominic C. Jenner

    2009-01-01

    Full Text Available Brucellosis is a prevalent zoonotic disease and is endemic in the Middle East, South America, and other areas of the world. In this study, complete inventories of putative functional ABC systems of five Brucella species have been compiled and compared. ABC systems of Brucella melitensis 16M, Brucella abortus 9-941, Brucella canis RM6/66, Brucella suis 1330, and Brucella ovis 63/290 were identified and aligned. High numbers of ABC systems, particularly nutrient importers, were found in all Brucella species. However, differences in the total numbers of ABC systems were identified (B. melitensis, 79; B. suis, 72; B. abortus 64; B. canis, 74; B. ovis, 59 as well as specific differences in the functional ABC systems of the Brucella species. Since B. ovis is not known to cause human brucellosis, functional ABC systems absent in the B. ovis genome may represent virulence factors in human brucellosis.

  6. Separated two-phase flow regime parameter measurement by a high speed ultrasonic pulse-echo system.

    Science.gov (United States)

    Masala, Tatiana; Harvel, Glenn; Chang, Jen-Shih

    2007-11-01

    In this work, a high speed ultrasonic multitransducer pulse-echo system using a four transducer method was used for the dynamic characterization of gas-liquid two-phase separated flow regimes. The ultrasonic system consists of an ultrasonic pulse signal generator, multiplexer, 10 MHz (0.64 cm) ultrasonic transducers, and a data acquisition system. Four transducers are mounted on a horizontal 2.1 cm inner diameter circular pipe. The system uses a pulse-echo method sampled every 0.5 ms for a 1 s duration. A peak detection algorithm (the C-scan mode) is developed to extract the location of the gas-liquid interface after signal processing. Using the measured instantaneous location of the gas/liquid interface, two-phase flow interfacial parameters in separated flow regimes are determined such as liquid level and void fraction for stratified wavy and annular flow. The shape of the gas-liquid interface and, hence, the instantaneous and cross-sectional averaged void fraction is also determined. The results show that the high speed ultrasonic pulse-echo system provides accurate results for the determination of the liquid level within +/-1.5%, and the time averaged liquid level measurements performed in the present work agree within +/-10% with the theoretical models. The results also show that the time averaged void fraction measurements for a stratified smooth flow, stratified wavy flow, and annular flow qualitatively agree with the theoretical predictions.

  7. A Novel Flow Measurement System for Cryogenic Two-Phase Flow Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Flow rate measurements for cryogenic propellants are required for spacecraft and space exploration systems. Such a requirement has been hampered by lack of fast and...

  8. Interfacial Area and Interfacial Transfer in Two-Phase Flow Systems (Volume II. Chapters 6-10)

    Energy Technology Data Exchange (ETDEWEB)

    Guo, T.; Park, J.; Kojasoy, G.

    2003-03-15

    Experiments were performed on horizontal air-water bubbly two-phase flow, axial flow, stratified wavy flow, and annular flow. Theoretical studies were also undertaken on interfacial parameters for a horizontal two-phase flow.

  9. Interfacial Area and Interfacial Transfer in Two-Phase Flow Systems (Volume III. Chapters 11-14)

    Energy Technology Data Exchange (ETDEWEB)

    Guo, T.; Park, J.; Kojasoy, G.

    2003-03-15

    Experiments were performed on horizontal air-water bubbly two-phase flow, axial flow, stratified wavy flow, and annular flow. Theoretical studies were also undertaken on interfacial parameters for a horizontal two-phase flow.

  10. Interfacial Area and Interfacial Transfer in Two-Phase Flow Systems (Volume IV. Chapters 15-19)

    Energy Technology Data Exchange (ETDEWEB)

    Guo, T.; Park, J.; Kojasoy, G.

    2003-03-15

    Experiments were performed on horizontal air-water bubbly two-phase flow, axial flow, stratified wavy flow, and annular flow. Theoretical studies were also undertaken on interfacial parameters for a horizontal two-phase flow.

  11. Interfacial Area and Interfacial Transfer in Two-Phase Flow Systems (Volume I. Chapters 1-5)

    Energy Technology Data Exchange (ETDEWEB)

    Guo, T.; Park, J.; Kojasoy, G.

    2003-03-15

    Experiments were performed on horizontal air-water bubbly two-phase flow, axial flow, stratified wavy flow, and annular flow. Theoretical studies were also undertaken on interfacial parameters for a horizontal two-phase flow.

  12. Thermodynamic modelling of phase equilibrium for water + poly(Ethylene glycol + salt aqueous two-phase systems

    Directory of Open Access Journals (Sweden)

    R.A.G. Sé

    2002-04-01

    Full Text Available The NRTL (nonrandom, two-liquid model, expressed in mass fraction instead of mole fraction, was used to correlate liquid-liquid equilibria for aqueous two-phase polymer-salt solutions. New interaction energy parameters for this model were determined using reported data on the water + poly(ethylene glycol + salt systems, with different molecular masses for PEG and the salts potassium phosphate, sodium sulfate, sodium carbonate and magnesium sulfate. The correlation of liquid-liquid equilibrium is quite satisfactory.

  13. Studies of efficiency in a perforated rotating disc contactor using a polymer-polymer aqueous two-phase systems

    Directory of Open Access Journals (Sweden)

    L. A. Sarubbo

    2005-09-01

    Full Text Available The mass transfer process in a perforated rotating disc contactor (PRDC using a polymer-polymer aqueous two-phase system was investigated. The results show that the efficiency did not show a regular trend with the increase of the dispersed phase velocity and increased with the rotation velocity. The separation efficiency was higher for three rotating discs than for four discs. The increase in tie-line length decreased the efficiency. The separation efficiency reached high values, about 96% under conditions studied in this work.

  14. Partition Coefficients of Amino Acids, Peptides, and Enzymes in Dextran + Poly(Ethylene Glycol) + Water Aqueous Two-Phase Systems

    Energy Technology Data Exchange (ETDEWEB)

    Kakisaka, Keijiro.; Shindo, Takashi.; Iwai, Yoshio.; Arai, Yasuhiko. (Kyushu University, Fukuoka (Japan). Department of Chemical Systems and Engineering)

    1998-12-01

    Partition coefficients are measured for five amino acids(aspartic acid, asparagine, methionine, cysteine and histidine) and tow peptides(glycyl-glycine and hexa-glycine) in dextran + poly(ethylene glycol) + water aqueous two-phase system. The partition coefficients of the amino acids and peptides are aorrelated using the osmotic virial equation. The interaction coefficients contained in the equation can be calculated by hydrophilic group parameters. The partition coefficients of [alpha]-amylase calculated by the osmotic virial equation with the hydrophilic group parameters are in fairly good agreement with the experimental data, though a relatively large discrepancy is shown for [beta]-amylase. (author)

  15. Partition Coefficients of Amino Acids, Peptides, and Enzymes in Dextran + Poly(Ethylene Glycol) + Water Aqueous Two-Phase Systems

    Energy Technology Data Exchange (ETDEWEB)

    Kakisaka, Keijiro.; Shindo, Takashi.; Iwai, Yoshio.; Arai, Yasuhiko. [Kyushu University, Fukuoka (Japan). Department of Chemical Systems and Engineering

    1998-12-01

    Partition coefficients are measured for five amino acids(aspartic acid, asparagine, methionine, cysteine and histidine) and tow peptides(glycyl-glycine and hexa-glycine) in dextran + poly(ethylene glycol) + water aqueous two-phase system. The partition coefficients of the amino acids and peptides are aorrelated using the osmotic virial equation. The interaction coefficients contained in the equation can be calculated by hydrophilic group parameters. The partition coefficients of {alpha}-amylase calculated by the osmotic virial equation with the hydrophilic group parameters are in fairly good agreement with the experimental data, though a relatively large discrepancy is shown for {beta}-amylase. (author)

  16. COUPLING MODEL OF TWO PHASE FLOW IN A FRACTURE-ROCK MATRIX SYSTEM AND ITS STOCHASTIC FEATURE ANALYSIS

    Institute of Scientific and Technical Information of China (English)

    王经明; 李竞生; 高智联; 杨保禹

    1998-01-01

    This study is concerned with developing a two-dimensional two-phase model thatsimulate the movement of non-aqueous phase liquid (NAPL) in a fracture-rock matrix system. Theintrinsic permeability and the fracture aperture are represented in the model via its Karhunen-Loeve expansion. Other parameters and the nodal unknowns, water saturations and waterpressures, are represented by their stochastic spectral expanions. The errors resulting fromtruncation of Karhunen - Loeve and polynomial chaos expansions to a finite number of terms areanalyzed. The eigenvalues of stochastic process is found out for any point in the special domain ofthe problem at any instant in time.

  17. Local existence and stability for a hyperbolic-elliptic system modeling two-phase reservoir flow

    Directory of Open Access Journals (Sweden)

    H. J. Schroll

    2000-01-01

    Full Text Available A system arising in the modeling of oil-recovery processes is analyzed. It consists of a hyperbolic conservation law governing the saturation and an elliptic equation for the pressure. By an operator splitting approach, an approximate solution is constructed. For this approximation appropriate a-priori bounds are derived. Applying the Arzela-Ascoli theorem, local existence and uniqueness of a classical solution for the original hyperbolic-elliptic system is proved. Furthermore, convergence of the approximation generated by operator splitting towards the unique solution follows. It is also proved that the unique solution is stable with respect to perturbations of the initial data.

  18. Partition of Chiral pharmaceutical intermediate R(-)-Mandelic Acid in Aqueous Two-Phase System of Poly(ethylene glycol)-Ammonium Sulfate

    Institute of Scientific and Technical Information of China (English)

    Xu Xiaoping; Li Zhongqin; Chen Jiebo; Huang Xinghua

    2004-01-01

    An aqueous two-phase system of poly (ethylene glycol)-ammonium sulfate was employed to separate R (-)-mandelic acid.The result showed that R (-)-mandelic acid has priority to partition in PEG-rich top phase. This indicated that aqueous two-phase is a very suitable system for separation of R(-)-mandelic acid.

  19. A Novel Aqueous Two Phase System Composed of a Thermo-Separating Polymer and an Organic Solvent for Purification of Thermo-Acidic Amylase Enzyme from Red Pitaya (Hylocereus polyrhizus Peel

    Directory of Open Access Journals (Sweden)

    Mehrnoush Amid

    2014-05-01

    Full Text Available The purification of thermo-acidic amylase enzyme from red pitaya (Hylocereus polyrhizus peel for the first time was investigated using a novel aqueous two-phase system (ATPS consisting of a thermo-separating copolymer and an organic solvent. The effectiveness of different parameters such as molecular weight of the thermo-separating ethylene oxide-propylene oxide (EOPO copolymer and type and concentration of organic solvent on the partitioning behavior of amylase was investigated. In addition, the effects of phase components, volume ratio (VR, pH and crude load of purification factor and yield of amylase were evaluated to achieve the optimum partition conditions of the enzyme. In the novel ATPS method, the enzyme was satisfactorily partitioned into the polymer-rich top phase in the system composed of 30% (w/w EOPO 2500 and 15% (w/w 2-propanol, at a volume ratio of 1.94 and with a crude load scale of 25% (w/w at pH 5.0. Recovery and recycling of components was also measured in each successive step of the ATPS process. The enzyme was successfully recovered by the method with a high purification factor of 14.3 and yield of 96.6% and copolymer was also recovered and recycled at a rate above 97%, making the method was more economical than the traditional ATPS method.

  20. A novel aqueous two phase system composed of a thermo-separating polymer and an organic solvent for purification of thermo-acidic amylase enzyme from red pitaya (Hylocereus polyrhizus) peel.

    Science.gov (United States)

    Amid, Mehrnoush; Manap, Yazid; Zohdi, Nor Khanani

    2014-05-22

    The purification of thermo-acidic amylase enzyme from red pitaya (Hylocereus polyrhizus) peel for the first time was investigated using a novel aqueous two-phase system (ATPS) consisting of a thermo-separating copolymer and an organic solvent. The effectiveness of different parameters such as molecular weight of the thermo-separating ethylene oxide-propylene oxide (EOPO) copolymer and type and concentration of organic solvent on the partitioning behavior of amylase was investigated. In addition, the effects of phase components, volume ratio (VR), pH and crude load of purification factor and yield of amylase were evaluated to achieve the optimum partition conditions of the enzyme. In the novel ATPS method, the enzyme was satisfactorily partitioned into the polymer-rich top phase in the system composed of 30% (w/w) EOPO 2500 and 15% (w/w) 2-propanol, at a volume ratio of 1.94 and with a crude load scale of 25% (w/w) at pH 5.0. Recovery and recycling of components was also measured in each successive step of the ATPS process. The enzyme was successfully recovered by the method with a high purification factor of 14.3 and yield of 96.6% and copolymer was also recovered and recycled at a rate above 97%, making the method was more economical than the traditional ATPS method.

  1. Energetic Efficiency of Mixing and Mass Transfer in Single Phase and Two-Phase Systems

    Directory of Open Access Journals (Sweden)

    Bałdyga Jerzy

    2017-03-01

    Full Text Available In this work a concept of energetic efficiency of mixing is presented and discussed; a classical definition of mixing efficiency is modified to include effects of the Schmidt number and the Reynolds number. Generalization to turbulent flows is presented as well. It is shown how the energetic efficiency of mixing as well as efficiencies of drop breakage and mass transfer in twophase liquid-liquid systems can be identified using mathematical models and test chemical reactions. New expressions for analyzing efficiency problem are applied to identify the energetic efficiency of mixing in a stirred tank, a rotor stator mixer and a microreactor. Published experimental data and new results obtained using new systems of test reactions are applied. It has been shown that the efficiency of mixing is small in popular types of reactors and mixers and thus there is some space for improvement.

  2. Two-Phase Thermal Switching System for a Small, Extended Duration Lunar Science Platform

    Science.gov (United States)

    Bugby, D.; Farmer, J.; OConnor, B.; Wirzburger, M.; Abel, E.; Stouffer, C.

    2010-01-01

    Issue: extended duration lunar science platforms, using solar/battery or radioisotope power, require thermal switching systems that: a) Provide efficient cooling during the 15-earth-day 390 K lunar day; b) Consume minimal power during the 15-earth-day 100 K lunar night. Objective: carry out an analytical study of thermal switching systems that can meet the thermal requirements of: a) International Lunar Network (ILN) anchor node mission - primary focus; b) Other missions such as polar crater landers. ILN Anchor Nodes: network of geophysical science platforms to better understand the interior structure/composition of the moon: a) Rationale: no data since Apollo seismic stations ceased operation in 1977; b) Anchor Nodes: small, low-power, long-life (6-yr) landers with seismographic and a few other science instruments (see next chart); c) WEB: warm electronics box houses ILN anchor node electronics/batteries. Technology Need: thermal switching system that will keep the WEB cool during the lunar day and warm during the lunar night.

  3. Purification of papain by metal affinity partitioning in aqueous two-phase polyethylene glycol/sodium sulfate systems.

    Science.gov (United States)

    Jiang, Zhi-Guo; Zhang, Hai-De; Wang, Wei-Tao

    2015-05-01

    A simple and inexpensive aqueous two-phase affinity partitioning system using metal ligands was introduced to improve the selectivity of commercial papain extraction. Polyethylene glycol 4000 was first activated using epichlorohydrin, then it was covalently linked to iminodiacetic acid. Finally, the specific metal ligand Cu(2+) was attached to the polyethylene glycol-iminodiacetic acid. The chelated Cu(2+) content was measured by atomic absorption spectrometry as 0.88 mol/mol (polyethylene glycol). The effects on the purification at different conditions, including polyethylene glycol molecular weight (2000, 4000, and 6000), concentration of phase-forming components (polyethylene glycol 12-20% w/w and sodium sulfate 12-20%, w/w), metal ligand type, and concentration, system pH and the commercial papain loading on papain extraction, were systematically studied. Under optimum conditions of the system, i.e. 18% w/w sodium sulfate, 18% w/w polyethylene glycol 4000, 1% w/w polyethylene glycol-iminodiacetic acid-Cu(2+) and pH 7, a maximum yield of 90.3% and a degree of purification of 3.6-fold were obtained. Compared to aqueous two phase extraction without ligands, affinity partitioning was found to be an effective technique for the purification of commercial papain with higher extraction efficiency and degree of purification.

  4. Effect of sodium chloride on solute-solvent interactions in aqueous polyethylene glycol-sodium sulfate two-phase systems.

    Science.gov (United States)

    da Silva, Nuno R; Ferreira, Luisa A; Madeira, Pedro P; Teixeira, José A; Uversky, Vladimir N; Zaslavsky, Boris Y

    2015-12-18

    Partition behavior of eight small organic compounds and six proteins was examined in poly(ethylene glycol)-8000-sodium sulfate aqueous two-phase systems containing 0.215M NaCl and 0.5M osmolyte (sorbitol, sucrose, TMAO) and poly(ethylene glycol)-10000-sodium sulfate-0.215M NaCl system, all in 0.01M sodium phosphate buffer, pH 6.8. The differences between the solvent properties of the coexisting phases (solvent dipolarity/polarizability, hydrogen bond donor acidity, and hydrogen bond acceptor basicity) were characterized with solvatochromic dyes using the solvatochromic comparison method. Differences between the electrostatic properties of the phases were determined by analysis of partitioning of sodium salts of dinitrophenylated (DNP-) amino acids with aliphatic alkyl side-chain. The partition coefficients of all compounds examined (including proteins) were described in terms of solute-solvent interactions. The results obtained in the study show that solute-solvent interactions of nonionic organic compounds and proteins in polyethylene glycol-sodium sulfate aqueous two-phase system change in the presence of NaCl additive.

  5. Two-Phase Thermal Switching System for a Small, Extended Duration Lunar Surface Science Platform

    Science.gov (United States)

    Bugby, David C.; Farmer, Jeffery T.; OConnor, Brian F.; Wirzburger, Melissa J.; Abel, Elisabeth D.; Stouffer, Chuck J.

    2010-01-01

    This paper describes a novel thermal control system for the Warm Electronics Box (WEB) on board a small lunar surface lander intended to support science activities anywhere on the lunar surface for an extended duration of up to 6 years. Virtually all lander electronics, which collectively dissipate about 60 W in the reference mission, are contained within the WEB. These devices must be maintained below 323 K (with a goal of 303 K) during the nearly 15-earth-day lunar day, when surface temperatures can reach 390K, and above 263 K during the nearly 15-earth-day lunar night, when surface temperatures can reach 100K. Because of the large temperature swing from lunar day-to-night, a novel thermal switching system was required that would be able to provide high conductance from WEB to radiator(s) during the hot lunar day and low (or negligible) conductance during the cold lunar night. The concept that was developed consists of ammonia variable conductance heat pipes (VCHPs) to collect heat from WEB components and a polymer wick propylene loop heat pipe (LHP) to transport the collected heat to the radiator(s). The VCHPs autonomously maximize transport when the WEB is warm and autonomously shut down when the WEB gets cold. The LHP autonomously shuts down when the VCHPs shut down. When the environment transitions from lunar night to day, the VCHPs and LHP autonomously turn back on. Out of 26 analyzed systems, this novel arrangement was able to best achieve the combined goals of zero control power, autonomous operation, long life, low complexity, low T, and landed tilt tolerance.

  6. Measurement of two-phase particle flow based on the characteristics of particle-system scattering

    Science.gov (United States)

    Li, Min; Zhang, Yang; Wang, Yuan; Yang, Bin

    2017-02-01

    Precise measurement of the mass of moving particles (MPM) is fundamental to the research on particle flows. In non-intrusive optical measurements, traditional discrete methods obtain the MPM by determining the connected domains on experimental pictures, leading to inevitable errors. In this study, the constitutive relationship between the MPM and the foreground grey scale value of the experimental picture is investigated on the basis of the working principle of digital cameras and the scattering theory of particle systems. This relationship is confirmed to be effective in wind-blown sand particle flow experiments using high-speed photography.

  7. Chemiluminescence detection of organic peroxides in a two-phase system.

    Science.gov (United States)

    Baj, Stefan; Krawczyk, Tomasz

    2007-02-28

    Potential application of chemiluminescence (CL) reaction of luminol for detection of organic peroxides by HPLC post-column reaction using an immiscible apolar eluent (hexane) with aqueous solution of luminol has been proposed. The positive influence of the addition of an anionic surface-active agent--sodium dodecyl sulphate (SDS) to the luminol solution on the CL intensity has been observed. The sensitivity of the method is greater for peroxyacid and hydroperoxide tested, and lesser for diacyl peroxide as compared to system with polar eluent miscible with solution of luminol. Our interpretation of observed results based on the extraction efficiency, CL kinetics and microemulsion formation has been suggested.

  8. Partition of volatile compounds in pea globulin-maltodextrin aqueous two-phase system.

    Science.gov (United States)

    Nguyen, Thanh Dat; Lafarge, Céline; Murat, Chloé; Mession, Jean-Luc; Cayot, Nathalie; Saurel, Rémi

    2014-12-01

    This study is based on the assumption that the off-flavour of pea proteins might be decreased using the retention of volatile compounds by a mixture with another biopolymer. The partition of volatile compounds in an aqueous system containing pea protein and maltodextrins was followed under thermodynamic incompatibility conditions. Firstly, the phase diagram of the system was established. Then, the partition of aroma compounds between the phase rich in protein and the phase rich in maltodextrin was measured by SPME-GC-MS. There was a transfer of volatile compounds during phase separation. Variations of pH were also used to vary the retention of volatile compounds by proteins. The concentration of volatile compounds in protein solution at pH 2.4 was higher than at pH 7.2. It was possible to increase the transfer of volatile compounds from the phase rich in protein to the phase rich in maltodextrin using the effect of pH on protein denaturation.

  9. Optimization of fibrinolytic enzyme production by Bacillus subtilis DC-2 in aqueous two-phase system (poly-ethylene glycol 4000 and sodium sulfate).

    Science.gov (United States)

    Ashipala, Onesmus K; He, Qian

    2008-07-01

    The central composite rotable design (CCRD) was used to determine optimal conditions for fibrinolytic enzyme production by Bacillus subtilis DC-2 in poly-ethylene glycol 4000 (PEG 4000) and sodium sulfate (Na(2)SO(4)) aqueous two-phase system (ATPS). PEG 4000 and Na(2)SO(4) concentration, fermentation time and temperature, and pH were selected as variables to evaluate the fibrinolytic activity in PEG phase. Using response surface methodology (RSM), a second-order polynomial equation was obtained by multiple regression analysis. The predicted maximal fibrinolytic activity in PEG phase was 1241.02 IU/ml with 9.05% PEG 4000 concentration, 5.06% Na(2)SO(4) concentration, 118.77 h fermentation time, 37.57 degrees C fermentation temperature and pH 6.52. The validity of the response model was verified by a good agreement between predicted and experimental results. The fibrinolytic activity obtained from experimental results in PEG phase (1223.61 IU/ml) was higher than that produced in homogeneous fermentation (1165.58 IU/ml).

  10. Numerical Simulation of One- and Two-Phase Flows in Propulsion Systems

    Science.gov (United States)

    Gilinsky, Mikhail; Verma, Arun; Hardin, Jay C.; Banerjee, Debrup; Blankson, Isaiah M.; Hendricks, Robert C.; Shvets, Alexander I.

    2003-01-01

    Four subprojects were conducted using analytical methods, numerical simulation and experimental tests: (A) Shock wave mitigation by spike-shaped blunt bodies with application for the purpose of drag, lift and longitudinal momentum optimization. The main result in this subproject is: application of a single needle against a supersonic flow provides higher benefits for blunt body drag reduction and heat transfer to the body than the application of multiple needles. (B) Solid particles, liquid and air jet injection through the front of a blunt body against a supersonic flow. In this case, the research conducted and analysis of multiple previous investigations in this area have shown essential benefits and preferable application of solid particle injection. (C) Comparison of different methods of fuel injection into supersonic duct flows. Preliminary numerical simulations and theoretical analysis show promising results for Telescope-shaped inlet applications in SCRAMJET; and (D) Development of an acoustic source location method for different applications including propulsion systems.

  11. Can affinity interactions influence the partitioning of glucose-6-phosphate dehydrogenase in two-phase aqueous micellar systems?

    Directory of Open Access Journals (Sweden)

    André M. Lopes

    2008-01-01

    Full Text Available In this work, we provide an investigation of the role and strength of affinity interactions on the partitioning of the glucose-6-phosphate dehydrogenase in aqueous two-phase micellar systems. These systems are constituted of micellar surfactant solutions and offer both hydrophobic and hydrophilic environments, providing selectivity to biomolecules. We studied G6PD partitioning in systems composed of the nonionic surfactants, separately, in the presence and absence of affinity ligands. We observed that G6PD partitions to the micelle-poor phase, owing to the strength of excluded-volume interactions in these systems that drive the protein to the micelle-poor phase, where there is more free volume available.

  12. Isolation and fractionation of CHO chromosomes in aqueous two phase systems using charged polymers and base specific macroligands.

    Science.gov (United States)

    Klaar, J; Kula, M R

    1986-02-01

    Chromosomes were isolated in a preparative scale by synchronisation of CHO cells with a double Thymidine block followed by an arrest in the metaphase by addition of Colcemid. Under proper cultivation conditions a mitotic index of 77% total cells could be routinely achieved. Bulk chromosome preparations free of nuclei and other subcellular particles have been obtained by low speed centrifugation followed by a 60 transfer countercurrent distribution using aqueous two phase systems composed of polyethylenglycol and dextran. The partition of CHO chromosomes previously purified in aqueous two phase systems were studied further to develop a protocol for the separation and isolation of individual chromosomes. Partition experiments with chromosomes changing the electrostatic phase potential by addition of charged PEG-derivatives suggest the existence of relatively highly charged chromosome groups. Most promising results with regard to separation were obtained using two PEG-derivatives, which interact specifically with the bases in DNA. For this affinity partitioning a GC- and AT-specific macroligand were employed. Comparing CCD's using each of these ligands information on the GC and AT content of exposed DNA in the chromosomes groups could be derived, demonstrating that specific sequences of DNA are accessible at the surface of metaphase chromosomes.

  13. Influence of ultrasonic condition on phase transfer catalyzed radical polymerization of methyl methacrylate in two phase system - A kinetic study.

    Science.gov (United States)

    Marimuthu, Elumalai; Murugesan, Vajjiravel

    2017-09-01

    An ultrasonic condition assisted phase transfer catalyzed radical polymerization of methyl methacrylate was investigated in an ethyl acetate/water two phase system at 60±1°C and 25kHz, 300W under inert atmosphere. The influence of monomer, initiator, catalyst and temperature, volume fraction of aqueous phase on the rate of polymerization was examined in detail. The reaction order was found to be unity for monomer, initiator and catalyst. Generally, the reaction rate was relatively fast in two phase system, when a catalytic amount of phase transfer catalyst was used. The combined approach, use of ultrasonic and PTC condition was significantly enhances the rate of polymerization. An ultrasonic and phase transfer catalyzed radical polymerization of methyl methacrylate has shown about three fold enhancements in the rate compared with silent polymerization of MMA using cetyltrimethylammonium bromide as PTC. The resultant kinetics was evaluated with silent polymerization and an important feature was discussed. The activation energy and other thermodynamic parameters were computed. Based on the obtained results an appropriate radical mechanism has been derived. TGA showed the polymer was stable up to 150°C. The FT-IR and DSC analysis validates the atactic nature of the obtained polymer. The XRD pattern reveals the amorphous nature of polymer was dominated. Copyright © 2016 Elsevier B.V. All rights reserved.

  14. A novel anaerobic two-phase system for biohydrogen production and in situ extraction of organic acid byproducts.

    Science.gov (United States)

    Sarma, Saurabh Jyoti; Brar, Satinder Kaur; Le Bihan, Yann; Buelna, Gerardo

    2015-06-01

    Owing to CO2-free emission, hydrogen is considered as a potential green alternative of fossil fuels. Water is the major emission of hydrogen combustion process and gravimetric energy density of hydrogen is nearly three times more than that of gasoline and diesel fuel. Biological hydrogen production, therefore, has commercial significance; especially, when it is produced from low-cost industrial waste-based feedstock. Light independent anaerobic fermentation is simple and mostly studied method of biohydrogen production. During hydrogen production by this method, a range of organic acid byproducts are produced. Accumulation of these byproducts is inhibitory for hydrogen production as it may result in process termination due to sharp decrease in medium pH or by possible metabolic shift. For the first time, therefore, a two-phase anaerobic bioreactor system has been reported for biohydrogen production which involves in situ extraction of different organic acids. Among different solvents, based on biocompatibility oleyl alcohol has been chosen as the organic phase of the two-phase system. An organic:aqueous phase ratio of 1:50 has been found to be optimum for hydrogen production. The strategy was capable of increasing the hydrogen production from 1.48 to 11.65 mmol/L-medium.

  15. Numerical Simulation of One- and Two-Phase Flows in Propulsion Systems

    Science.gov (United States)

    Gilinsky, Mikhail; Patel, Kaushal; Alexander, Casey; Thompson, Tyesha; Blankson, Isaiah M.; Shvets, Alexander I.; Gromov, Valery G.; Sakharov, Vladimir I.

    2001-01-01

    In this report, we present some results of problems investigated during joint research between the Hampton University Fluid Mechanics and Acoustics Laboratory (HU/FM&AL), NASA GRC, and the LaRC Hyper-X Program. This work is supported by joint research between the NASA GRC and the Institute of Mechanics at Moscow State University (IM/MSU) in Russia under a CRDF grant. The main areas of current scientific interest of the HU/FM&AL include an investigation of the proposed and patented advanced methods for aircraft engine thrust and noise benefits. These methods are based on nontraditional 3D corrugated and composite nozzle, inlet, propeller and screw designs such as a Bluebell and Telescope nozzle, Mobius-shaped screw, etc. This is the main subject of our other projects, of which one is presented at the current conference. Here we analyze additional methods for exhaust jet noise reduction without essential thrust loss and even with thrust augmentation. Such additional approaches are: (1) to add some solid, fluid, or gas mass at discrete locations to the main supersonic gas stream to minimize the negative influence of strong shock waves formed in propulsion systems. This mass addition may be accompanied by heat addition to the main stream as a result of the fuel combustion or by cooling of this stream as a result of the liquid mass evaporation and boiling; (2) Use of porous or permeable nozzles and additional shells at the nozzle exit for preliminary cooling of the hot jet exhaust and pressure compensation for off-design conditions (so-called continuous ejector with small mass flow rate); and (3) to propose and analyze new effective methods of fuel injection into the flow stream in air-breathing engines. The research is focused on a wide regime of problems in the propulsion field as well as in experimental testing and theoretical and numerical simulation analyses for advanced aircraft and rocket engines. The FM&AL Team uses analytical methods, numerical simulations, and

  16. Effects of Hydrophobicity of Ethylene Oxide-Propylene Oxide Copolymers on Phase Diagrams of Aqueous Two-Phase Systems and Partition Behaviors of Cephalexin and 7-Aminodeacetoxicephalos Doranic Acid

    Institute of Scientific and Technical Information of China (English)

    朱建航; 魏东芝; 曹学君

    2002-01-01

    A series of ethylene oxide (EO)-propylene oxide (PO) random co-polymers (EOPO) were used to formaqueous two-phase systems (ATPS) with ammonium sulfate. Effects of EOPO's properties on the phase separationbehaviors and on the partition of cephalexin and 7-aminodesacetoxicephalosporanic acid (7-ADCA) in ATPS wereinvestigated. Both the molar mass and molar ratio of EO to PO of EOPO could greatly influence partition behaviorsof cephalexin and 7-ADCA as well as the binodal curve of ATPS. With the increase of molar mass of co-polymeror the decrease of molar ratio of EO to PO, the critical point of ATPS decreased, the binodal curve became moreasymmetry, and both cephalexin and 7-ADCA followed the same tendency to partition into the polymer-poorbottom phase. The experimental results shows that it is feasible to partition cephalexin and 7-ADCA in either thepolymer-rich top phase or the polymer-poor bottom phase by choosing a specific phase-forming EOPO.

  17. Comparative performance and microbial community of single-phase and two-phase anaerobic systems co-digesting cassava pulp and pig manure

    DEFF Research Database (Denmark)

    Panichnumsin, P.; Ahring, B.K.; Nopharatana, A.

    2010-01-01

    In this study, we illustrated the performance and microbial community of single- and two-phase systems anaerobically co-digesting cassava pulp and pig manure. The results showed that the volatile solid reduction and biogas productivity of two-phase CSTR were 66 ± 4% and 2000 ± 210 ml l-1 d-1, whi...

  18. Design of aqueous two-phase systems for purification of hyaluronic acid produced by metabolically engineered Lactococcus lactis.

    Science.gov (United States)

    Rajendran, Vivek; Puvendran, Kirubhakaran; Guru, Bharath Raja; Jayaraman, Guhan

    2016-02-01

    Hyaluronic acid has a wide range of biomedical applications and its commercial value is highly dependent on its purity and molecular weight. This study highlights the utility of aqueous two-phase separation as a primary recovery step for hyaluronic acid and for removal of major protein impurities from fermentation broths. Metabolically engineered cultures of a lactate dehydrogenase mutant strain of Lactococcus lactis (L. lactis NZ9020) were used to produce high-molecular-weight hyaluronic acid. The cell-free fermentation broth was partially purified using a polyethylene glycol/potassium phosphate system, resulting in nearly 100% recovery of hyaluronic acid in the salt-rich bottom phase in all the aqueous two-phase separation experiments. These experiments were optimized for maximum removal of protein impurities in the polyethylene glycol rich top phase. The removal of protein impurities resulted in substantial reduction of membrane fouling in the subsequent diafiltration process, carried out with a 300 kDa polyether sulfone membrane. This step resulted in considerable purification of hyaluronic acid, without any loss in recovery and molecular weight. Diafiltration was followed by an adsorption step to remove minor impurities and achieve nearly 100% purity. The final hyaluronic acid product was characterized by Fourier-transform IR and NMR spectroscopy, confirming its purity.

  19. Comparative assessment of olive oil mill effluents from three-phase and two-phase systems, treated for hydrogen production.

    Science.gov (United States)

    Rouvalis, A; Iliopoulou-Georgudaki, J

    2010-10-01

    By-products of a two-phase and a three-phase olive oil mill process treated in an anaerobic fermentation system for hydrogen production, were evaluated by three bioassays: the zebrafish Danio rerio embryo test and two microbiotests, Thamnotoxkit F and Daphtoxkit F™ pulex. Samples from both processes were classified as "very toxic" with LC(50) values ranging from 1.52% (T. platyurus 24 h test) to 4.48% (D. pulex 48 h-LC₅₀). Toxicity values were differently correlated to physicochemical parameters showing different degree of influence. The treated effluents of both process systems remained very toxic showing the necessity for further treatment, aiming to environmentally safe discharges.

  20. Measurement and Correlation of Partition Coefficients of Baicalin in EOPO/Salt Aqueous Two-Phase Systems

    Institute of Scientific and Technical Information of China (English)

    李伟; 朱自强

    2002-01-01

    The partition coefficients of baicalin were measured in ethylene oxide and propylene oxide(EOPO)/salt aqueous two-phase systems at 298.15K,It was found that most of baicalin partitioned into EOPO-rich phase.The partition coefficients of baicalin varied from 10 to 120.The effect of various factors,including tie-line lngth,salt composition,molecular weight of EOPO,and solution pH,on the partition behavior was investigated on EOPO/salt systems.Furthermore the partition coefficients of baicalin were correlated using the modified Diamond-Hsu model.Good agreement with experimental data is obtained.The average relative deviations are less than 5.0%.

  1. Energetic and exploitation characteristics of a two-phase ejecting vacuum system built in the paper machine at A.D. Komuna Skopje

    Directory of Open Access Journals (Sweden)

    Šarevski Milan

    2004-01-01

    Full Text Available This work presents the concept of a two-phase ejecting vacuum system. The energetic characteristics of these systems were analyzed and compared to those with mechanical pumps with water ring and turbo compressor vacuum pumps. A method for optimizing a two-phase thermo compressor vacuum systems is presented. The analysis included the exploitation characteristics of the system developed at A.D. "Komuna" Skopje.

  2. Aqueous two-phase systems: A simple methodology to obtain mixtures enriched in main toxins of Bothrops alternatus venom.

    Science.gov (United States)

    Gomez, Gabriela; Leiva, Laura; Nerli, Bibiana Beatriz

    2016-08-01

    Phospholipase A2 (PLA2) and protease (P) are enzymes responsible of myotoxic, edematogenic and hemostasis disorder effects observed in the envenomation by Bothrops alternatus pitviper. Their partitioning coefficient (Kp) in different polyethyleneglycol/potassium phosphate aqueous two-phase systems (ATPSs) was determined in order to both achieve a better understanding of the partitioning mechanism and define optimal conditions for toxin isolation. Polyethyleneglycols (PEGs) of molecular weights 1000; 3350; 6000 and 8000; different temperatures (5, 20 and 37 °C) and phase volume ratios of 0.5; 1 and 2 were assayed. PLA2 partitioned preferentially to the top phase while P mainly distributed to the bottom phase. Either entropically- or enthalpically-driven mechanisms were involved in each case (PLA2 and P). The aqueous two-phase system formed by PEG of MW 3350 (12.20% wt/wt) and KPi pH 7.0 (11.82% wt/wt) with a volume ratio of one and a load of 1.25 mg of venom/g of system showed to be the most efficient to recover both enzymes. It allowed obtaining the 72% of PLA2 in the top phase with a purification factor of 2 and the 82% of P at the bottom phase simultaneously. A further adsorption batch step with DEAE-cellulose was used to remove satisfactorily the PEG from the top phase and recover the active PLA2. The proposed methodology is simple, inexpensive, and only requires professionals trained in handling basic laboratory equipment. It could be easily adoptable by developing countries in which the snakebite accidents cause considerable morbidity and mortality.

  3. Phase Diagrams of the Aqueous Two-Phase Systems of Poly(ethylene glycol/Sodium Polyacrylate/Salts

    Directory of Open Access Journals (Sweden)

    Adalberto Pessoa Junior

    2011-03-01

    Full Text Available Aqueous two-phase systems consisting of polyethylene glycol (PEG, sodium polyacrylate (NaPAA, and a salt have been studied. The effects of the polymer size, salt type (NaCl, Na2SO4, sodium adipate and sodium azelate and salt concentrations on the position of the binodal curve were investigated. The investigated PEG molecules had a molar mass of 2,000 to 8,000 g/mol, while that of NaPAA was 8,000 g/mol. Experimental phase diagrams, and tie lines and calculated phase diagrams, based on Flory-Huggins theory of polymer solutions are presented. Due to strong enthalpic and entropic balancing forces, the hydrophobicity of the added salt has a strong influence on the position of the binodal, which could be reproduced by model calculations.

  4. A continuous-flow ATP amplification system for increasing the sensitivity of quantitative bioluminescence assay

    OpenAIRE

    Satoh, Tetsuya; Shinoda, Yasuharu; Alexandrov, Maxym; Kuroda, Akio; Murakami, Yuji

    2008-01-01

    We constructed a novel ATP amplification reactor using a continuous-flow system, and this allowed us to increase the sensitivity of quantitative bioluminescence assay by controlling the number of ATP amplification cycles. We previously developed a bioluminescence assay coupled with ATP amplification using a batch system. However, it was difficult to control the number of amplification cycles. In this study, ATP amplification was performed using a continuous-flow system, and significant linear...

  5. Modeling and investigation of refrigeration system performance with two-phase fluid injection in a scroll compressor

    Science.gov (United States)

    Gu, Rui

    Vapor compression cycles are widely used in heating, refrigerating and air-conditioning. A slight performance improvement in the components of a vapor compression cycle, such as the compressor, can play a significant role in saving energy use. However, the complexity and cost of these improvements can block their application in the market. Modifying the conventional cycle configuration can offer a less complex and less costly alternative approach. Economizing is a common modification for improving the performance of the refrigeration cycle, resulting in decreasing the work required to compress the gas per unit mass. Traditionally, economizing requires multi-stage compressors, the cost of which has restrained the scope for practical implementation. Compressors with injection ports, which can be used to inject economized refrigerant during the compression process, introduce new possibilities for economization with less cost. This work focuses on computationally investigating a refrigeration system performance with two-phase fluid injection, developing a better understanding of the impact of injected refrigerant quality on refrigeration system performance as well as evaluating the potential COP improvement that injection provides based on refrigeration system performance provided by Copeland.

  6. Two phase sampling

    CERN Document Server

    Ahmad, Zahoor; Hanif, Muhammad

    2013-01-01

    The development of estimators of population parameters based on two-phase sampling schemes has seen a dramatic increase in the past decade. Various authors have developed estimators of population using either one or two auxiliary variables. The present volume is a comprehensive collection of estimators available in single and two phase sampling. The book covers estimators which utilize information on single, two and multiple auxiliary variables of both quantitative and qualitative nature. Th...

  7. Extraction of natural red colorants from the fermented broth of Penicillium purpurogenum using aqueous two-phase polymer systems.

    Science.gov (United States)

    Santos-Ebinuma, Valéria Carvalho; Lopes, André Moreni; Pessoa, Adalberto; Teixeira, Maria Francisca Simas

    2015-01-01

    Safety concerns related to the increasing and widespread application of synthetic coloring agents have increased the demand for natural colorants. Fungi have been employed in the production of novel and safer colorants. In order to obtain the colorants from fermented broth, suitable extraction systems must be developed. Aqueous two-phase polymer systems (ATPPS) offer a favorable chemical environment and provide a promising alternative for extracting and solubilizing these molecules. The aim of this study was to investigate the partitioning of red colorants from the fermented broth of Penicillium purpurogenum using an ATPPS composed of poly(ethylene glycol) (PEG) and sodium polyacrylate (NaPA). Red colorants partitioned preferentially to the top (PEG-rich phase). In systems composed of PEG 6,000 g/mol/NaPA 8,000 g/mol, optimum colorant partition coefficient (KC ) was obtained in the presence of NaCl 0.1 M (KC  = 10.30) while the PEG 10,000 g/mol/NaPA 8,000 g/mol system in the presence of Na2 SO4 0.5 M showed the highest KC (14.78). For both polymers, the mass balance (%MB) and yield in the PEG phase (%ηTOP ) were close to 100 and 79%, respectively. The protein selectivity in all conditions evaluated ranged from 2.0-3.0, which shows a suitable separation of the red colorants and proteins present in the fermented broth. The results suggest that the partitioning of the red colorants is dependent on both the PEG molecular size and salt type. Furthermore, the results obtained support the potential application of ATPPS as the first step of a purification process to recover colorants from fermented broth of microorganisms.

  8. Phase behavior and molecular dynamics simulation studies of new aqueous two-phase separation systems induced by HEPES buffer.

    Science.gov (United States)

    Taha, Mohamed; Khoiroh, Ianatul; Lee, Ming-Jer

    2013-01-17

    Here, for the first time, we show that with addition of a biological buffer, 4-(2-hydroxyethyl)piperazine-1-ethanesulfonic acid (HEPES), into aqueous solutions of tetrahydrofuran (THF), 1,3-dioxolane, 1,4-dioxane, 1-propanol, 2-propanol, tert-butanol, acetonitrile, or acetone, the organic solvent can be excluded from water to form a new liquid phase. The phase diagrams have been determined at ambient temperature. In order to understand why and how a zwitterion solute (HEPES) induced phase separation of the investigated systems, molecular dynamics (MD) simulation studies are performed for HEPES + water + THF system. The MD simulations were conducted for the aqueous mixtures with 12 different compositions. The reliability of the simulation results of HEPES in pure water and beyond the phase separation mixtures was justified by comparing the densities obtained from MD with the experimental values. The simulation results of HEPES in pure THF and in a composition inside the phase separation region were justified qualitatively. Interestingly, all HEPES molecules entirely aggregated in pure THF. This reveals that HEPES is insoluble in pure THF, which is consistent with the experimental results. Even more interestingly, the MD simulation for the mixture with composition inside the phase separation region showed the formation of two phases. The THF molecules are squeezed out from the water network into a new liquid phase. The hydrogen bonds (HBs), HB lifetime, HB Gibbs energy (ΔG), radial distribution functions (RDFs), coordination numbers (CNs), electrostatic interactions, and the van der Waals interactions between the different species have been analyzed. Further, MD simulations for the other phase separation systems by choosing a composition inside the two liquids region for each system were also simulated. Our findings will therefore pave the way for designing new benign separation auxiliary agents.

  9. Microcalorimetric Study on the Oscillating System of Two-phase Reaction of Aqueous Acid with Primary Amine in Chloroform

    Institute of Scientific and Technical Information of China (English)

    ZHANG,Hong-Lin; YU,Xiu-Fang; LU,Cheng-Xue; SUN,Si-Xiu; GUO,Guo-Hua; FU,Xun

    2003-01-01

    It has been found that the two-phase reactions of aqueous HCl,HOAc or H3PO4 with primary amine N1923 in chloroform are oscillating reactions. Their power-time curves were measured by the titration microcalorimetric method, and the induction period (tin).The first oscillating period (tp.1) and the second oscillating period(tp.2 ) were determined.The apparent activating parameters and the orders of the oscillating systems were calculated and the following relationships were established: for the oscillating system of hydrochloric acid tin∝c0.147HCIexp(1.35×103/T),.tp.1∝c0.241HCI·exp(4.33×103/T),tp.2∝c0.290HCIexp(5.59×103/T);for the oscillating system of acetic acid, tm∝c0.883HOAcexp(2.32×103/T),tp.1∝c0.399HOAc·exp(4.50×103/T),tp.2∝c0.301HOAcexp(5.88×103/T),for the oscillating system of phosphoric acid, tim∝c1.14H3PO4exp(7.70×104]T),tp.1∝c1.42H3PO4exp(1.14×104/T),tp.2∝c1.47H3PO4exp(1.27×104/T).

  10. Evidence for Two Phases of Galaxy Formation from Radial Trends in the Globular Cluster System of NGC 1407

    CERN Document Server

    Forbes, Duncan; Strader, Jay; Romanowsky, Aaron; Brodie, Jean; Foster, Caroline

    2011-01-01

    Here we present the colours of individual globular clusters (GCs) around the massive elliptical galaxy NGC 1407 out to a projected galactocentric radius of 140 kpc or 17 galaxy effective radii (R$_e$). Such data are a proxy for the halo metallicity. We find steep, and similar, metallicity gradients of ~ -0.4 dex per dex for both the blue (metal-poor) and red (metal-rich) GC subpopulations within 5-8.5 R_e (40-70 kpc). At larger radii the mean GC colours (metallicity) are constant. A similar behaviour is seen in a wide-field study of M87's GC system, and in our own Galaxy. We interpret these radial metallicity trends to indicate an inner region formed by early in-situ dissipative processes and an outer halo formed by ongoing accretion of low mass galaxies and their GCs. These results provide observational support for the model of galaxy formation whereby massive galaxies form inside-out in two phases. We have also searched the literature for other massive early-type galaxies with reported GC metallicity gradie...

  11. High-calorific biogas production from anaerobic digestion of food waste using a two-phase pressurized biofilm (TPPB) system.

    Science.gov (United States)

    Li, Yeqing; Liu, Hong; Yan, Fang; Su, Dongfang; Wang, Yafei; Zhou, Hongjun

    2017-01-01

    To obtain high calorific biogas via anaerobic digestion without additional upgrading equipment, a two-phase pressurized biofilm system was built up, including a conventional continuously stirred tank reactor and a pressurized biofilm anaerobic reactor (PBAR). Four different pressure levels (0.3, 0.6, 1.0 and 1.7MPa) were applied to the PBAR in sequence, with the organic loading rate maintained at 3.1g-COD/L/d. Biogas production, gas composition, process stability parameters were measured. Results showed that with the pressure increasing from 0.3MPa to 1.7MPa, the pH value decreased from 7.22±0.19 to 6.98±0.05, the COD removal decreased from 93.0±0.9% to 79.7±1.2% and the methane content increased from 80.5±1.5% to 90.8±0.8%. Biogas with higher calorific value of 36.2MJ/m(3) was obtained at a pressure of 1.7MPa. Pressure showed a significant effect on biogas production and gas quality in methanogenesis reactor. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Relative hydrophobicity between the phases and partition of cytochrome-c in glycine ionic liquids aqueous two-phase systems.

    Science.gov (United States)

    Wu, Changzeng; Wang, Jianji; Li, Zhiyong; Jing, Jun; Wang, Huiyong

    2013-08-30

    In this work, glycine ionic liquids tetramethylammonium glycine ([N1111][Gly]), tetraethylammonium glycine ([N2222][Gly]), tetra-n-butylammonium glycine ([N4444][Gly]), tetra-n-butylphosphonium glycine ([P4444][Gly]) and tetra-n-pentylammonium glycine ([N5555][Gly]) were synthesized and used to prepare aqueous two-phase systems (ATPSs) in the presence of K2HPO4. Binodal curves of such ATPSs and partition coefficients of a series of dinitrophenylated (DNP) amino acids in these ATPSs were determined at 298.15K to understand the effect of cationic structure of the ionic liquids on the phase-forming ability of glycine ionic liquids, relative hydrophobicity between the phases in the ionic liquids ATPSs, and polarity of the ionic liquids-rich phases. With the attempt to correlate the relative hydrophobicity of the phases in the ATPSs with their extraction capability for proteins, partition coefficients of cytochrome-c in the ATPSs were also determined. It was shown that partition coefficients of cytochrome-c were in the range from 2.83 to 20.7 under the studied pH conditions. Then, hydrophobic interactions between cytochrome-c and the ionic liquid are suggested to be the main driving force for the preferential partition of cytochrome-c in the glycine ionic liquid-rich phases of the ATPSs. Result derived from polarity of the ionic liquids-rich phases supports this mechanism.

  13. Partial purification of glucose-6-phosphate dehydrogenase by aqueous two-phase poly(ethyleneglycol/phosphate systems Purificação parcial de glucose-6-fosfato desidrogenase por sistemas de duas fases aquosas poli (etilenoglicol/fosfato

    Directory of Open Access Journals (Sweden)

    Marcela Zanella Ribeiro

    2007-03-01

    Full Text Available Glucose-6-phosphate dehydrogenase (G6PDH is an important enzyme used in biochemical and medical studies and in several analytical methods that have industrial and commercial application. This work evaluated the extraction of G6PDH in aqueous two-phase system (ATPS of poly(ethyleneglycol (PEG/phosphate buffer, using as enzyme source a medium prepared through commercial baker's yeast disruption. Firstly, the effects of PEG molar mass on the enzyme partition and of homogenization and rest on the system equilibrium were investigated. Afterwards, several ATPS were prepared using statistical analysis (2² factorial design. The results, including kinetic and thermodynamic parameters for the G6PDH activity, showed partial purification of this enzyme in ATPS composed of 17.5% (w/w PEG400 and 15.0% (w/w phosphate. A high enzymatic recovery value (97.7%, a high partition coefficient (351, and an acceptable purification factor (2.28 times higher than in cell homogenate were attained from the top phase. So, it was possible to attain an effective enzyme pre-purification by separating some contaminants with a simple method such as liquid-liquid extraction in aqueous two-phase systems (ATPS.Glicose-6-fosfato desidrogenase (G6PDH é uma importante enzima usada em estudos bioquímicos e médicos, bem como em diversos métodos analíticos com aplicação comercial e industrial. Neste trabalho foi avaliado a extração da G6PDH em sistemas de duas fases aquosas (ATPS constituídos por poli(etilenoglicol (PEG/tampão fosfato, usando como fonte de enzima um meio preparado por rompimento de leveduras de panificação comercial. Inicialmente foram investigados os efeitos da massa molar do PEG na partição da enzima e da homogeneização e repouso no equilíbrio do sistema. Na sequência, diversos ATPS foram preparados usando análise estatística (planejamento fatorial 2². Os resultados, incluindo parâmetros cinéticos e termodinâmicos para a atividade da G6PDH

  14. Continuous-flow ATP amplification system for increasing the sensitivity of quantitative bioluminescence assay.

    Science.gov (United States)

    Satoh, Tetsuya; Shinoda, Yasuharu; Alexandrov, Maxym; Kuroda, Akio; Murakami, Yuji

    2008-08-01

    We constructed a novel ATP amplification reactor using a continuous-flow system, and this allowed us to increase the sensitivity of a quantitative bioluminescence assay by controlling the number of ATP amplification cycles. We previously developed a bioluminescence assay coupled with ATP amplification using a batch system. However, it was difficult to control the number of amplification cycles. In this study, ATP amplification was performed using a continuous-flow system, and significant linear correlations between amplified luminescence and initial ATP concentration were observed. When performing four cycles of continuous-flow ATP amplification, the gradient of amplification was 1.87(N). Whereas the lower quantifiable level was 500 pM without amplification, values as low as 50 pM ATP could be measured after amplification. The sensitivity thus increased 10-fold, with further improvements expected with additional amplification cycles. The continuous-flow system thus effectively increased the sensitivity of the quantitative bioluminescence assay.

  15. Partitioning and purification of extracellular β-1,3-1,4-glucanase in aqueous two-phase systems

    Institute of Scientific and Technical Information of China (English)

    HE Guo-qing; ZHANG Xiu-yan; TANG Xing-jun; CHEN Qi-he; RUAN Hui

    2005-01-01

    The partition behaviors of β-1,3-1,4-glucanase, α-amylase and neutral proteases from clarified and whole fermentation broths of Bacillus subtilis ZJF-1A5 were investigated. An aqueous two-phase system (polyethylene glycol (PEG)/MgSO4)was examined with regard to the effects of PEG molecular weight (MW) and concentration, MgSO4 concentration, pH and NaCl concentration on enzyme partition and extraction. The MW and concentration of PEG were found to have significant effects on enzyme partition and extraction with low MW PEG showing the greatest benefit in the partition and extraction of β-glucanase with the PEG/MgSO4 system. MgSO4 concentration influenced the partition and extraction of β-glucanase significantly. pH had little effect on β-glucanase or proteases partition but affected α-amylase partition when pH was over 7.0. The addition of NaCl had little effect on the partition behavior of β-glucanase but had very significant effects on the partitioning of α-amylase and on the neutral proteases. The partition behaviors of β-glucanase, α-amylase and proteases in whole broth were also investigated and results were similar to those obtained with clarified fermentation broth. A two-step process for purifying β-glucanase was developed, which achieved β-glucanase recovery of 65.3% and specific activity of 14027 U/mg, 6.6 times improvement over the whole broth.

  16. Influence of salts on the coexistence curve and protein partitioning in nonionic aqueous two-phase micellar systems

    Directory of Open Access Journals (Sweden)

    A. M. Lopes

    2014-12-01

    Full Text Available Aqueous two-phase micellar systems (ATPMS can be exploited in separation science for the extraction/purification of desired biomolecules. Prior to phase separation the surfactant solution reaches a cloud point temperature, which is influenced by the presence of electrolytes. In this work, we provide an investigation on the cloud point behavior of the nonionic surfactant C10E4 in the presence of NaCl, Li2SO4 and KI. We also investigated the salts' influence on a model protein partitioning. NaCl and Li2SO4 promoted a depression of the cloud point. The order of salts and the concentration that decreased the cloud point was: Li2SO4 0.5 M > NaCl 0.5 M ≈ Li2SO4 0.2 M. On the other hand, 0.5 M KI dislocated the curve to higher cloud point values. For our model protein, glucose-6-phosphate dehydrogenase (G6PD, partitioning experiments with 0.5 M NaCl or 0.2 M Li2SO4 at 13.85 ºC showed similar results, with K G6PD ~ 0.46. The lowest partition coefficient was obtained in the presence of 0.5 M KI (K G6PD = 0.12, with major recovery of the enzyme in the micelle-dilute phase (%Recovery = 90%. Our results show that choosing the correct salt to add to ATPMS may be useful to attain the desired partitioning conditions at more extreme temperatures. Furthermore, this system can be effective to separate a target biomolecule from fermented broth contaminants.

  17. One-Step Generation of Cell-Encapsulating Compartments via Polyelectrolyte Complexation in an Aqueous Two Phase System.

    Science.gov (United States)

    Hann, Sarah D; Niepa, Tagbo H R; Stebe, Kathleen J; Lee, Daeyeon

    2016-09-28

    Diverse fields including drug and gene delivery and live cell encapsulation require biologically compatible encapsulation systems. One widely adopted means of forming capsules exploits cargo-filled microdroplets in an external, immiscible liquid phase that are encapsulated by a membrane that forms by trapping of molecules or particles at the drop surface, facilitated by the interfacial tension. To eliminate the potentially deleterious oil phase often present in such processes, we exploit the aqueous two phase system of poly(ethylene glycol) (PEG) and dextran. We form capsules by placing dextran-rich microdroplets in an external PEG-rich phase. Strong polyelectrolytes present in either phase form complexes at the drop interface, thereby forming a membrane encapsulating the fluid interior. This process requires considerable finesse as both polyelectrolytes are soluble in either the drop or external phase, and the extremely low interfacial tension is too weak to provide a strong adsorption site for these molecules. The key to obtaining microcapsules is to tune the relative fluxes of the two polyelectrolytes so that they meet and complex at the interface. We identify conditions for which complexation can occur inside or outside of the drop phase, resulting in microparticles or poor encapsulation, respectively, or when properly balanced, at the interface, resulting in microcapsules. The resulting microcapsules respond to the stimuli of added salts or changes in osmotic pressure, allowing perturbation of capsule permeability or triggered release of capsule contents. We demonstrate that living cells can be sequestered and interrogated by encapsulating Pseudomonas aeruginosa PAO1 and using a Live/Dead assay to assess their viability. This method paves the way to the formation of a broad variety of versatile functional membranes around all aqueous capsules; by tuning the fluxes of complexing species to interact at the interface, membranes comprising other complexing

  18. Numerical modelling of the impact of a liquid drop on the surface of a two-phase fluid system

    Science.gov (United States)

    Sochan, Agata; Lamorski, Krzysztof; Bieganowski, Andrzej; Ryżak, Magdalena

    2014-05-01

    The aim of the study was validation of a numerical model of the impact of a liquid drop on the surface of a two-phase system of immiscible fluids. The drop impact phenomenon was recorded using a high-speed camera (Vision Research MIRO M310) and the data were recorded at 2000 frames per second. The numerical calculations were performed with the Finite Volume Method (FVM) solving the three-dimensional Navier-Stokes equations for three phases: air and two selected immiscible fluids. The Volume of Fluid (VOF) technique was employed for modelling of the boundaries between the phases. Numerical modelling was done with the Finite Volume Method using an available OpenFOAM software. The experiment was based on three variables: • the height from which the drop of the selected fluids fell (the speed of the drop), • the thickness of the layers of the two selected immiscible fluids (a thin layer of the fluid with a lower density was spread over the higher-density fluid), • the size of the fluid droplet. The velocity and radius of the falling drop was calculated based on the recorded images. The used parameters allowed adequate projection of the impact of fluid droplets on a system of two immiscible liquids. Development of the numerical model of splash may further have practical applications in environmental protection (spraying of hazardous fluids, spread of fuels and other hazardous substances as a result of disasters, spraying (water cooling) of hot surfaces), and in agriculture (prevention of soil erosion). The study was partially funded from the National Science Centre (Poland) based on the decision no. DEC-2012/07/N/ST10/03280.

  19. Application of aqueous two-phase systems for the development of a new method of cobalt(II), iron(III) and nickel(II) extraction: a green chemistry approach.

    Science.gov (United States)

    Patrício, Pamela da Rocha; Mesquita, Maiby Cabral; da Silva, Luis Henrique Mendes; da Silva, Maria C Hespanhol

    2011-10-15

    We have investigated the extraction behavior of the metallic ions Co(II), Fe(III) and Ni(II) as a function of the amount of potassium thiocyanate used as an extracting agent, using the following aqueous two-phase systems (ATPS): PEO + (NH(4))(2)SO(4) + H(2)O, PEO + Li(2)SO(4) + H(2)O, L35 + (NH(4))(2)SO(4) + H(2)O and L35 + (Li)(2)SO(4)+H(2)O. Metal extraction from the salt-rich phase to the polymer-rich phase is affected by the following parameters: amount of added extractant, pH, and the nature of the electrolyte and polymer that forms the ATPS. Maximal extraction percentages were obtained for Co(II) (99.8%), Fe(III) (12.7%) and Ni(II) (3.17%) when the ATPS was composed of PEO1500 + (NH(4))(2)SO(4) + H(2)O containing 1.4 mmol of KSCN at pH 4.0, providing separation factors as high as S(Co, Fe) = 3440 and S(Co, Ni) = 15,300. However, when the same ATPS was used at pH 2.0, the maximal extraction percentages for iron and nickel were 99.5% and 4.34%, respectively, with S(Fe, Ni) equal to 4380. The proposed technique was shown to be efficient in the extraction of Co(II) and Fe(III), with large viability for the selective separation of Co(II) and Fe(III) ions in the presence of Ni(II).

  20. Enabling two-phase microfluidic thermal transport systems using a novel thermal-flux degassing and fluid charging approach

    Science.gov (United States)

    Singh Dhillon, Navdeep; Pisano, Albert P.

    2014-03-01

    A novel two-port thermal-flux method has been proposed and demonstrated for degassing and charging two-phase microfluidic thermal transport systems with a degassed working fluid. In microscale heat pipes and loop heat pipes (mLHPs), small device volumes and large capillary forces associated with smaller feature sizes render conventional vacuum pump-based degassing methods quite impractical. Instead, we employ a thermally generated pressure differential to purge non-condensable gases from these devices before charging them with a degassed working fluid in a two-step process. Based on the results of preliminary experiments studying the effectiveness and reliability of three different high temperature-compatible device packaging approaches, an optimized compression packaging technique was developed to degas and charge a mLHP device using the thermal-flux method. An induction heating-based noninvasive hermetic sealing approach for permanently sealing the degassed and charged mLHP devices has also been proposed. To demonstrate the efficacy of this approach, induction heating experiments were performed to noninvasively seal 1 mm square silicon fill-hole samples with donut-shaped solder preforms. The results show that the minimum hole sealing induction heating time is heat flux limited and can be estimated using a lumped capacitance thermal model. However, further continued heating of the solder uncovers the hole due to surface tension-induced contact line dynamics of the molten solder. It was found that an optimum mass of the solder preform is required to ensure a wide enough induction-heating time window for successful sealing of a fill-hole.

  1. The formation and physical stability of two-phase solid dispersion systems of indomethacin in supercooled molten mixtures with different matrix formers.

    Science.gov (United States)

    Semjonov, Kristian; Kogermann, Karin; Laidmäe, Ivo; Antikainen, Osmo; Strachan, Clare J; Ehlers, Henrik; Yliruusi, Jouko; Heinämäki, Jyrki

    2017-01-15

    Amorphous solid dispersions (SDs) are a promising approach to improve the dissolution rate of and oral bioavailability of poorly water-soluble drugs. In some cases multi-phase, instead of single-phase, SD systems with amorphous drug are obtained. While it is widely assumed that one-phase amorphous systems are desirable, two-phase systems may still potentially exhibit enhanced stability and dissolution advantages over undispersed systems. The objective of the present study was to understand the solid-state properties of two-phase SDs with amorphous drug and their relation to physical stability. Two different types of excipients for SD formation were used, one being a polymer and the other a small molecule excipient. The supercooled molten SDs of a poorly water-soluble indomethacin (IND) with a graft copolymer, Soluplus® (SOL) and sugar alcohol, xylitol (XYL) were prepared. Supercooled molten SDs of IND with SOL were two-phase glassy suspension in which the amorphous drug was dispersed in an amorphous polymer matrix. A short-term aging of the SDs led to the formation of glassy suspensions where the crystalline drug was dispersed in an amorphous polymer matrix. These were physically stable at room temperature for the time period studied (RT, 23±2°C), but aging at high-humidity conditions (75% RH) recrystallization to metastable α-IND occurred. Interestingly, the SDs with XYL were two-phase amorphous precipitation systems in which the drug was in an amorphous form in the crystalline sugar alcohol matrix. The SDs of IND and XYL exhibited fast drug recrystallization. In conclusion, the preparation method of two-phase systems via co-melting in association with the rapid quench cooling is a feasible method for the formulation of poorly water-soluble drugs. The physical stability of these two-phase systems, however, is dependent on the carrier material and storage conditions.

  2. 双水相体系在无机盐分离中的应用%Application of Aqueous - two Phase System in the Separation of Inorganic Salts

    Institute of Scientific and Technical Information of China (English)

    史许娜; 韩清华

    2016-01-01

    Different separation methods of potassium chloride and ammonium chloride mixture are ana-lyzed. The present situation for separating mixed solution of potassium chloride and ammonium chloride by aqueous two - phase system(1 - propanol - KCl - NH4 Cl - H2 O aqueous two - phase system)is intro-duced,and the application of aqueous two - phase system is expanded.%分析了氯化钾和氯化铵混合溶液的不同分离方法,介绍了双水相体系(正丙醇—氯化钾—氯化铵—水双水相体系)对该混合溶液的分离现状,拓展了双水相体系的应用范围。

  3. Comparative performance and microbial community of single-phase and two-phase anaerobic systems co-digesting cassava pulp and pig manure

    DEFF Research Database (Denmark)

    Panichnumsin, P.; Ahring, B.K.; Nopharatana, A.

    2010-01-01

    In this study, we illustrated the performance and microbial community of single- and two-phase systems anaerobically co-digesting cassava pulp and pig manure. The results showed that the volatile solid reduction and biogas productivity of two-phase CSTR were 66 ± 4% and 2000 ± 210 ml l-1 d-1, while...... predominant in both digesters while the relative abundance of Methanosaeta sp. and Methanospirillum hungatei differed between the two systems......., followed by the Clostridia in singlephase CSTR. In hydrolysis/acidification reactor of two-phase system, the bacteria within the phylum Firmicutes, especially Clostridium, Eubacteriaceae and Lactobacillus were the dominant phylogenetic groups. Among the Archaea, Methanosaeta sp. was the exclusive...

  4. Thermal-gravitational modeling and scaling of two-phase heat transport systems from micro-gravity to super-gravity levels

    Science.gov (United States)

    Delil, A. A. M.

    2001-02-01

    Earlier publications extensively describe NLR research on thermal-gravitational modeling and scaling of two-phase heat transport systems for spacecraft applications. These publications on mechanically and capillary pumped two-phase loops discuss pure geometric scaling, pure fluid to fluid scaling, and combined (hybrid) scaling of a prototype system by a model at the same gravity level, and of a prototype in micro-gravity environment by a scale-model on earth. More recent publications include the scaling aspects of prototype two-phase loops for Moon or Mars applications by scale-models on earth. Recent work, discussed here, concerns extension of thermal-gravitational scaling to super-g acceleration levels. This turned out to be necessary, since a very promising super-g application for (two-phase) heat transport systems will be cooling of high-power electronics in spinning satellites and in military combat aircraft. In such aircraft, the electronics can be exposed during maneuvres to transient accelerations up to 120 m/s2. The discussions focus on ``conventional'' (capillary) pumped two-phase loops. It can be considered as introduction to the accompanying article, which focuses on pulsating and oscillating devices. .

  5. Development of a Thermal Control System with Mechanically Pumped CO2 Two-Phase Loops for the AMS-02 Tracker on the ISS

    CERN Document Server

    Alberti, G; Ambrosi, G; Bardet, M; Battiston, R; Borsini, S; Cao, J F; Chen, Y; van Es, J; Gargiulo, C; Guo, K H; Guo, L; He, Z H; Huang, Z C; Koutsenko, V; Laudi, E; Lebedev, A; Lee, S C; Li, T X; Lin, Y L; Lv, S S; Menichelli, M; Miao, J Y; Mo, D C; Ni, J Q; Pauw, A; Qi, X M; Shue, G M; Sun, D J; Sun, X H; Tang, C P; Verlaat, B; Wang, Z X; Weng, Z L; Xiao, W J; Xu, N S; Yang, F K; Yeh, C C; Zhang, Z; Zwartbol, T

    2013-01-01

    To provide a stable thermal environment for the AMS-Tracker, a thermal control system based on mechanically pumped CO2 two-phase loops was developed. It has been operating reliably in space since May 19, 2011. In this article, we summarize the design, construction, tests, and performance of the AMS-Tracker thermal control system (AMS-TTCS).

  6. Recovery of ascorbic oxidoreductase from crude extract with an aqueous two-phase system in a perforated rotating disc contactor

    Directory of Open Access Journals (Sweden)

    Ana Lúcia Figueiredo Porto

    2004-09-01

    Full Text Available A continuous perforated rotating disc contactor was used to extract the enzyme ascorbic oxidoreductase (E.C.1.10.3.3 from crude extract of Curcubita maxima with an aqueous two-phase system of poly (ethylene glycol and phosphate salts. The effect of dispersed phase velocity on either protein mass transfer coefficients or separation efficiency at 1, 2 and 3 mL/min was studied. An increase of the mass transfer coefficients was observed with the dispersed phase velocity, while the separation efficiency showed a small decrease with the increase of this parameter. The experimental results obtained during continuous extraction showed that the ascorbic oxidoreductase activity was partitioned preferentially into the salt-rich phase in all conditions studied. The best recovery of enzyme activity was 236%, with a purification factor of 34 in flow rates of 1 mL/min for dispersed phase.Uma coluna de discos perfurados rotativos foi utilizada na extração da enzima ascorbato oxidorredutase (E.C.1.10.3.3, obtida do extrato bruto de Curcubita maxima, através da utilização do sistema bifásico aquoso Polietilenoglicol-sais de fosfato. Os efeitos da velocidade da fase dispersa nos coeficientes de transferência de massa e na eficiência de separação para valores de 1, 2 e 3 mL/min foram estudados. Observou-se um aumento da transferência de massa com a velocidade da fase dispersa, enquanto que a eficiência de separação demonstrou uma ligeira redução com o aumento deste parâmetro. Os resultados experimentais obtidos durante a extração contínua demonstraram que a atividade da ascorbato oxidorredutase se concentrou preferencialmente na fase rica em sal para todas as condições estudadas. A maior recuperação da atividade enzimática foi de 236%, com um fator de purificação de 34 para o valor de 1 mL/min para a fase dispersa.

  7. Maximizing the utilization of Laminaria japonica as biomass via improvement of alginate lyase activity in a two-phase fermentation system.

    Science.gov (United States)

    Oh, Yuri; Xu, Xu; Kim, Ji Young; Park, Jong Moon

    2015-08-01

    Brown seaweed contains up to 67% of carbohydrates by dry weight and presents high potential as a polysaccharide feedstock for biofuel production. To effectively use brown seaweed as a biomass, degradation of alginate is the major challenge due to its complicated structure and low solubility in water. This study focuses on the isolation of alginate degrading bacteria, determining of the optimum fermentation conditions, as well as comparing the conventional single fermentation system with the two-phase fermentation system which is separately using alginate and mannitol extracted from Laminaria japonica. Maximum yield of organic acids production and volatile solids reduction obtained were 0.516 g/g and 79.7%, respectively, using the two-phase fermentation system in which alginate fermentation was carried out at pH 7 and mannitol fermentation at pH 8. The two-phase fermentation system increased the yield of organic acids production by 1.14 times and led to a 1.45-times reduction of VS when compared to the conventional single fermentation system at pH 8. The results show that the two-phase fermentation system improved the utilization of alginate by separating alginate from mannitol leading to enhanced alginate lyase activity.

  8. Liquid–liquid equilibria in the quinary aqueous two-phase system of poly(ethylene glycol) 6000 + sodium sulfate + water in the presence of glucose and ethanol: Experimental investigation and thermodynamic modeling

    Energy Technology Data Exchange (ETDEWEB)

    Hekayati, Javad; Roosta, Aliakbar, E-mail: aa.roosta@sutech.ac.ir; Javanmardi, Jafar

    2016-02-10

    Highlights: • Quinary LLE phase equilibria involving PEG 6000 + Na{sub 2}SO{sub 4} + H{sub 2}O + glucose + ethanol. • Favorable partition coefficients of ethanol and glucose. • Satisfactory correlation of the LLE experimental data with the original NRTL model. • Root mean squared deviations (RMSDs) of less than 0.6%. - Abstract: Extractive fermentation processes involving aqueous two-phase systems (ATPSs) are considered as viable means of overcoming the problems associated with product inhibition. Practical development of these processes requires accurate knowledge of the liquid–liquid equilibrium (LLE) of the ATPS forming components alongside the substrate and product of the fermentation process. In this work, the quinary aqueous two-phase LLE of poly(ethylene glycol) 6000 + sodium sulfate + water in the presence of glucose and ethanol have been experimentally determined at 298.15 K using spectrophotometric methods. The resulting LLE data were then satisfactorily correlated by the non-random two-liquid (NRTL) activity coefficient model based on mass fractions. In doing so, the binary energy interaction parameters of the NRTL activity coefficient model were obtained and reported. Calculated RMS deviations below 0.6% demonstrate that the original NRTL activity coefficient model can accurately correlate the LLE data of the quinary aqueous biphasic system of interest.

  9. Preparation of aqueous two-phase systems composed of two pH-response polymers and liquid-liquid extraction of demeclocycline.

    Science.gov (United States)

    Yan, Bo; Cao, Xuejun

    2012-07-06

    Aqueous two-phase systems have potential applications for separation and purification of bioproducts in bio-industry. However, a key problem is the recovery of the polymers forming aqueous two-phase systems. In this study, two novel random copolymers (P(ADB) and P(ADBA)) were synthesized using acrylic acid, dimethylamino-ethyl methacrylate, butyl methacrylate and allyl alcohol as monomers and used to form pH response aqueous two-phase systems. The recoveries of P(ADB) and P(ADBA) are 97.18% and 98.87% and the pI of P(ADB) and P(ADBA) are 2.79 and 4.01, respectively. Demeclocycline was partitioned in the P(ADB)/P(ADBA) aqueous two-phase systems and the partition coefficient reached 0.085, in the presence of MgSO₄ (60 mmol/L) at pH 5.28. Copyright © 2012 Elsevier B.V. All rights reserved.

  10. An ATP System for Deep-Space Optical Communication

    Science.gov (United States)

    Lee, Shinhak; Irtuzm Gerardi; Alexander, James

    2008-01-01

    An acquisition, tracking, and pointing (ATP) system is proposed for aiming an optical-communications downlink laser beam from deep space. In providing for a direction reference, the concept exploits the mature technology of star trackers to eliminate the need for a costly and potentially hazardous laser beacon. The system would include one optical and two inertial sensors, each contributing primarily to a different portion of the frequency spectrum of the pointing signal: a star tracker (50 Hz. The outputs of these sensors would be combined in an iterative averaging process to obtain high-bandwidth, high-accuracy pointing knowledge. The accuracy of pointing knowledge obtainable by use of the system was estimated on the basis of an 8-cm-diameter telescope and known parameters of commercially available star trackers and inertial sensors: The single-axis pointing-knowledge error was found to be characterized by a standard deviation of 150 nanoradians - below the maximum value (between 200 and 300 nanoradians) likely to be tolerable in deep-space optical communications.

  11. Liquid-liquid equilibrium of water + PEG 8000 + magnesium sulfate or sodium sulfate aqueous two-phase systems at 35°C: experimental determination and thermodynamic modeling

    Directory of Open Access Journals (Sweden)

    B. D. Castro

    2005-09-01

    Full Text Available Liquid-liquid extraction using aqueous two-phase systems is a highly efficient technique for separation and purification of biomolecules due to the mild properties of both liquid phases. Reliable data on the phase behavior of these systems are essential for the design and operation of new separation processes; several authors reported phase diagrams for polymer-polymer systems, but data on polymer-salt systems are still relatively scarce. In this work, experimental liquid-liquid equilibrium data on water + polyethylene glycol 8000 + magnesium sulfate and water + polyethylene glycol 8000 + sodium sulfate aqueous two-phase systems were obtained at 35°C. Both equilibrium phases were analyzed by lyophilization and ashing. Experimental results were correlated with a mass-fraction-based NRTL activity coefficient model. New interaction parameters were estimated with the Simplex method. The mean deviations between the experimental and calculated compositions in both equilibrium phases is about 2%.

  12. Transformation of Vesicles in Aqueous Two-Phase System of an Anionic Gemini Surfactant and a Cationic Conventional Surfactant Mixture

    Institute of Scientific and Technical Information of China (English)

    JIANG Rong; HUANG Yi-Xiong; ZHAO Jian-Xi; HUANG Chang-Cang

    2008-01-01

    Transformation of vesicles formed in DTAB/C11-p-PhCNa aqueous surfactant two-phase (ASTP) was observed by the transmission electron microscopy (TEM). The trans-conformation of the gemini surfactant in the aggregates was considered to be the important factor for constructing the multi-lamellar structure of the vesicle wall. The cation-π interaction between the quaternary ammonium cation and the aromatic ring in the spacer was determined by the UV-Vis spectrum analysis, which, as well as the general electrostatic attraction and hydrophobic force, contributes to the stability of the multi-lamellar structure. The concentrations of the surface-active ions were measured for understanding the mechanism of vesicle transformation. The results show that isoelectric mixing of the two components benefits the growth of vesicles both in size and wall thickness.

  13. Increased production of megakaryocytes near purity from cord blood CD34+ cells using a short two-phase culture system.

    Science.gov (United States)

    Boyer, Lucie; Robert, Amélie; Proulx, Chantal; Pineault, Nicolas

    2008-03-20

    Expansion of hematopoietic progenitor cells (HPC) ex vivo remains an important focus in fundamental and clinical research. The aim of this study was to determine whether the implementation of such expansion phase in a two-phase culture strategy prior to the induction of megakaryocyte (Mk) differentiation would increase the yield of Mks produced in cultures. Toward this end, we first characterized the functional properties of five cytokine cocktails to be tested in the expansion phase on the growth and differentiation kinetics of CD34+-enriched cells, and on their capacity to expand clonogenic progenitors in cultures. Three of these cocktails were chosen based on their reported ability to induce HPC expansion ex vivo, while the other two represented new cytokine combinations. These analyses revealed that none of the cocktails tested could prevent the differentiation of CD34+ cells and the rapid expansion of lineage-positive cells. Hence, we sought to determine the optimum length of time for the expansion phase that would lead to the best final Mk yields. Despite greater expansion of CD34+ cells and overall cell growth with a longer expansion phase, the optimal length for the expansion phase that provided greater Mk yield at near maximal purity was found to be 5 days. Under such settings, two functionally divergent cocktails were found to significantly increase the final yield of Mks. Surprisingly, these cocktails were either deprived of thrombopoietin or of stem cell factor, two cytokines known to favor megakaryopoiesis and HPC expansion, respectively. Based on these results, a short resource-efficient two-phase culture protocol for the production of Mks near purity (>95%) from human CD34+ CB cells has been established.

  14. Integration of carboxyl modified magnetic particles and aqueous two-phase extraction for selective separation of proteins.

    Science.gov (United States)

    Gai, Qingqing; Qu, Feng; Zhang, Tao; Zhang, Yukui

    2011-07-15

    Both of the magnetic particle adsorption and aqueous two-phase extraction (ATPE) were simple, fast and low-cost method for protein separation. Selective proteins adsorption by carboxyl modified magnetic particles was investigated according to protein isoelectric point, solution pH and ionic strength. Aqueous two-phase system of PEG/sulphate exhibited selective separation and extraction for proteins before and after magnetic adsorption. The two combination ways, magnetic adsorption followed by ATPE and ATPE followed by magnetic adsorption, for the separation of proteins mixture of lysozyme, bovine serum albumin, trypsin, cytochrome C and myloglobin were discussed and compared. The way of magnetic adsorption followed by ATPE was also applied to human serum separation.

  15. A Novel Aqueous Two Phase System Composed of Surfactant and Xylitol for the Purification of Lipase from Pumpkin (Cucurbita moschata) Seeds and Recycling of Phase Components.

    Science.gov (United States)

    Amid, Mehrnoush; Manap, Mohd Yazid; Hussin, Muhaini; Mustafa, Shuhaimi

    2015-06-17

    Lipase is one of the more important enzymes used in various industries such as the food, detergent, pharmaceutical, textile, and pulp and paper sectors. A novel aqueous two-phase system composed of surfactant and xylitol was employed for the first time to purify lipase from Cucurbita moschata. The influence of different parameters such as type and concentration of surfactants, and the composition of the surfactant/xylitol mixtures on the partitioning behavior and recovery of lipase was investigated. Moreover, the effect of system pH and crude load on the degree of purification and yield of the purified lipase were studied. The results indicated that the lipase was partitioned into the top surfactant rich phase while the impurities partitioned into the bottom xylitol-rich phase using an aqueous two phase system composed of 24% (w/w) Triton X-100 and 20% (w/w) xylitol, at 56.2% of tie line length (TLL), (TTL is one of the important parameters in this study and it is determined from a bimodal curve in which the tie-line connects two nodes on the bimodal, that represent concentration of phase components in the top and bottom phases) and a crude load of 25% (w/w) at pH 8.0. Recovery and recycling of components was also measured in each successive step process. The enzyme was successfully recovered by the proposed method with a high purification factor of 16.4 and yield of 97.4% while over 97% of the phase components were also recovered and recycled. This study demonstrated that the proposed novel aqueous two phase system method is more efficient and economical than the traditional aqueous two phase system method for the purification and recovery of the valuable enzyme lipase.

  16. [Phase transfer catalyzed bioconversion of penicillin G to 6-APA by immobilized penicillin acylase in recyclable aqueous two-phase systems with light/pH sensitive copolymers].

    Science.gov (United States)

    Jin, Ke-ming; Cao, Xue-jun; Su, Jin; Ma, Li; Zhuang, Ying-ping; Chu, Ju; Zhang, Si-liang

    2008-03-01

    Immobilized penicillin acylase was used for bioconversion of penicillin PG into 6-APA in aqueous two-phase systems consisting of a light-sensitive polymer PNBC and a pH-sensitive polymer PADB. Partition coefficients of 6-APA was found to be about 5.78 in the presence of 1% NaCl. Enzyme kinetics showed that the reaction reached equilibrium at roughly 7 h. The 6-APA mole yields were 85.3% (pH 7.8, 20 degrees C), with about 20% increment as compared with the reaction of single aqueous phase buffer. The partition coefficient of PG (Na) varied scarcely, while that of the product, 6-APA and phenylacetic acid (PA) significantly varied due to Donnan effect of the phase systems and hydrophobicity of the products. The variation of the partition coefficients of the products also affected the bioconversion yield of the products. In the aqueous two-phase systems, the substrate, PG, the products of 6-APA and PA were biased in the top phase, while immobilized penicillin acylase at completely partitioned at the bottom. The substrate and PG entered the bottom phase, where it was catalyzed into 6-APA and PA and entered the top phase. Inhibition of the substrate and products was removed to result in improvement of the product yield, and the immobilized enzyme showed higher efficiency than the immobilized cells and occupied smaller volume. Compared with the free enzyme, immobilized enzyme had greater stability, longer life-time, and was completely partitioned in the bottom phase and recycle. Bioconversion in two-phase systems using immobilized penicillin acylase showed outstanding advantage. The light-sensitive copolymer forming aqueous two-phase systems could be recovered by laser radiation at 488 nm or filtered 450 nm light, while pH-sensitive polymer PADB could be recovered at the isoelectric point (pH 4.1). The recovery of the two copolymers was between 95% and 99%.

  17. A Novel Aqueous Two Phase System Composed of Surfactant and Xylitol for the Purification of Lipase from Pumpkin (Cucurbita moschata Seeds and Recycling of Phase Components

    Directory of Open Access Journals (Sweden)

    Mehrnoush Amid

    2015-06-01

    Full Text Available Lipase is one of the more important enzymes used in various industries such as the food, detergent, pharmaceutical, textile, and pulp and paper sectors. A novel aqueous two-phase system composed of surfactant and xylitol was employed for the first time to purify lipase from Cucurbita moschata. The influence of different parameters such as type and concentration of surfactants, and the composition of the surfactant/xylitol mixtures on the partitioning behavior and recovery of lipase was investigated. Moreover, the effect of system pH and crude load on the degree of purification and yield of the purified lipase were studied. The results indicated that the lipase was partitioned into the top surfactant rich phase while the impurities partitioned into the bottom xylitol-rich phase using an aqueous two phase system composed of 24% (w/w Triton X-100 and 20% (w/w xylitol, at 56.2% of tie line length (TLL, (TTL is one of the important parameters in this study and it is determined from a bimodal curve in which the tie-line connects two nodes on the bimodal, that represent concentration of phase components in the top and bottom phases and a crude load of 25% (w/w at pH 8.0. Recovery and recycling of components was also measured in each successive step process. The enzyme was successfully recovered by the proposed method with a high purification factor of 16.4 and yield of 97.4% while over 97% of the phase components were also recovered and recycled. This study demonstrated that the proposed novel aqueous two phase system method is more efficient and economical than the traditional aqueous two phase system method for the purification and recovery of the valuable enzyme lipase.

  18. Measurement and simulation of the turbulent dispersion of a radioactive tracer in a two-phase flow system

    Energy Technology Data Exchange (ETDEWEB)

    Hensel, F.; Rohde, U.

    1998-10-01

    The turbulent dispersion of a radiotracer in an experimental setup with a natural convection liquid-gaseous flow was investigated. A liquid-gaseous bubbly flow was generated in a narrow tank by injection of pressurized air into water or by catalytic disintegration of H{sub 2}O{sub 2}. Turbulent Prandtl numbers for gas and tracer dispersion were varied. In the case of higher gas superficial velocities (J{sub gas}{approx}5-15 mm/s), a reasonable agreement was achieved between calculated and measured tracer transport velocity and dispersion coefficient values. A nearly linear correlation between j{sub gas} and D was found in agreement with other authors. The calculation results contribute to a better understanding of the phenomena and interpretation of the measurement results as well as to the validation of the CFD code for turbulent two-phase flow applications. Further investigations are necessary to improve the agreement in the cases of H{sub 2}O{sub 2} disintegration and low gas superficial velocities. (orig.)

  19. Design and development of single stage purification of papain using Ionic Liquid based aqueous two phase extraction system and its Partition coefficient studies

    Directory of Open Access Journals (Sweden)

    Senthilkumar Rathnasamy

    2013-04-01

    Full Text Available As an emerging trend in bioseparation, aqueous two phase extractions based on phosponium ionic liquid have been utilized in this work to extract papain from Carica papaya fruit latex and the same wascompared with conventional aqueous two phase extraction system. Factors affecting the partition coefficient of papain such as ionic liquid concentration, pH of the extraction system and temperature have been investigated. The optimization studies show that ionic liquid concentrations and pH are majorly influencing the phaseformations and papain partitioning. It reveals the importance of electrostatic and hydrophobic interactions in the papain partitioning. Purification studies performed on Gel Filtration Chromatography shows that 96% of the papain enzyme could be extracted with the phosponium based ionic liquid in a single stage extraction. The final fraction containing papain enzyme was confirmed by SDS Page analysis.

  20. Study on constant-pressure specific heat of non-equi- librium phase change process in gas-liquid two-phase flow system

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    In this paper, the air-water vapor-water system is taken as an example, and the formula of constantpressure specific heat during non-equilibrium phase change process in the two-phase flow system is deduced using the theory of two-phase flow and thermophysics. The constant-pressure specific heat of non-equilibrium phase change process is calculated with the corresponding numerical model, and the numerical results are compared to those of the equilibrium phase change process. It is shown that in evaporation process, the variational rate of the non-equilibrium specific heat increases with increasing initial fluid temperature and particle mass fraction. The smaller particle radius is, the faster the variational rate is. Meanwhile, the constant-pressure specific heat of equilibrium process is higher than that of the non-equilibrium process all the time.

  1. Contribution to the thermodynamics of sc3+, y3+, la3+ and trivalent lanthanide cations in the two-phase water-nitrobenzene extraction system.

    Science.gov (United States)

    Makrlík, Emanuel; Vaňura, Petr

    2011-06-01

    From the exchange extraction constants corresponding to the general equilibrium M3+(aq) + 3H+(nb) M3+(nb) + 3H+(aq) occurring in the two-phase water-nitrobenzene system (M3+ = Sc3+, Y3+, La3+, Ce3+, Pr3+, Nd3+, Sm3+, Eu3+, Gd3+, Tb3+, Dy3+, Ho3+, Er3+, Tm3+, Yb3+, Lu3+; aq = aqueous phase, nb = nitrobenzene phase), the individual extraction constants of 16 trivalent metal cations were calculated. It was found that these individual extraction constants in the mentioned two-phase system increase in the following cation order: Sc3+ < Yb3+< Ho3+ < Er3+ < Tm3+, Lu3+ < Y3+, Dy3+ < Tb3+ < Gd3+ < Eu3+ < Sm3+ < Nd3+ < Pr3+ < La3+, Ce3+.

  2. Simultaneous separation/enrichment and detection of trace ciprofloxacin and lomefloxacin in food samples using thermosensitive smart polymers aqueous two-phase flotation system combined with HPLC.

    Science.gov (United States)

    Lu, Yang; Chen, Bo; Yu, Miao; Han, Juan; Wang, Yun; Tan, Zhenjiang; Yan, Yongsheng

    2016-11-01

    Smart polymer aqueous two phase flotation system (SPATPF) is a new separation and enrichment technology that integrated the advantages of the three technologies, i.e., aqueous two phase system, smart polymer and flotation sublation. Ethylene oxide and propylene oxide copolymer (EOPO)-(NH4)2SO4 SPATPF is a pretreatment technique, and it is coupled with high-performance liquid chromatography to analyze the trace ciprofloxacin and lomefloxacin in real food samples. The optimized conditions of experiment were determined in the multi-factor experiment by using response surface methodology. The flotation efficiency of lomefloxacin and ciprofloxacin was 94.50% and 98.23% under the optimized conditions. The recycling experimentsshowed that the smart polymer EOPO could use repeatedly, which will reduce the cost in the future application. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. Predicting the influence of compressibility and thermal and flow distribution asymmetry on the frequency-response characteristics of multitube two-phase condensing flow systems

    Energy Technology Data Exchange (ETDEWEB)

    Kobus, C.J.; Wedekind, G.L.; Bhatt, B.L.

    2000-02-01

    An equivalent single-tube model concept was extended to predict the frequency-response characteristics of multitube two-phase condensing flow systems, complete with the ability to predict the influence of compressibility and thermal and flow distribution asymmetry. The predictive capability of the equivalent single-tube model was verified experimentally with extensive data that encompassed a three-order-of-magnitude range of frequencies, and a wide range of operating parameters.

  4. Experimental study on two-phase flow natural circulation in a core catcher cooling channel for EU-APR1400 using air-water system

    Energy Technology Data Exchange (ETDEWEB)

    Song, Ki Won [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784 (Korea, Republic of); Korea Atomic Energy Research Institute, Daejeon 34057 (Korea, Republic of); Nguyen, Thanh Hung [School of Nuclear Engineering, Purdue University, West Lafayette, IN 47906 (United States); Ha, Kwang Soon; Kim, Hwan Yeol; Song, Jinho [Korea Atomic Energy Research Institute, Daejeon 34057 (Korea, Republic of); Park, Hyun Sun [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784 (Korea, Republic of); Revankar, Shripad T., E-mail: shripad@postech.ac.kr [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784 (Korea, Republic of); School of Nuclear Engineering, Purdue University, West Lafayette, IN 47906 (United States); Kim, Moo Hwan [Division of Advanced Nuclear Engineering, POSTECH, Pohang 790-784 (Korea, Republic of); Korea Institute of Nuclear Safety, Daejeon 305-338 (Korea, Republic of)

    2017-05-15

    Highlights: • Two-phase flow regimes and transition behavior were observed in the coolant channel. • Test were conducted for natural circulation with air-water. • Data were obtained on flow regime, void fraction, flow rates and re-wetting time. • The data were related to a cooling capability of core catcher system. - Abstract: Ex-vessel core catcher cooling system driven by natural circulation is designed using a full scaled air-water system. A transparent half symmetric section of a core catcher coolant channel of a pressurized water reactor was designed with instrumentations for local void fraction measurement and flow visualization. Two designs of air-water top separator water tanks are studied including one with modified ‘super-step’ design which prevents gas entrainment into down-comer. In the experiment air flow rates are set corresponding to steam generation rate for given corium decay power. Measurements of natural circulation flow rate, spatial local void fraction distribution and re-wetting time near the top wall are carried out for various air flow rates which simulate boiling-induced vapor generation. Since heat transfer and critical heat flux are strongly dependent on the water mass flow rate and development of two-phase flow on the heated wall, knowledge of two-phase flow characteristics in the coolant channel is essential. Results on flow visualization showing two phase flow structure specifically near the high void accumulation regions, local void profiles, rewetting time, and natural circulation flow rate are presented for various air flow rates that simulate corium power levels. The data are useful in assessing the cooling capability of and safety of the core catcher system.

  5. 'Domino' systems biology and the 'A' of ATP.

    Science.gov (United States)

    Verma, Malkhey; Zakhartsev, Maksim; Reuss, Matthias; Westerhoff, Hans V

    2013-01-01

    We develop a strategic 'domino' approach that starts with one key feature of cell function and the main process providing for it, and then adds additional processes and components only as necessary to explain provoked experimental observations. The approach is here applied to the energy metabolism of yeast in a glucose limited chemostat, subjected to a sudden increase in glucose. The puzzles addressed include (i) the lack of increase in adenosine triphosphate (ATP) upon glucose addition, (ii) the lack of increase in adenosine diphosphate (ADP) when ATP is hydrolyzed, and (iii) the rapid disappearance of the 'A' (adenine) moiety of ATP. Neither the incorporation of nucleotides into new biomass, nor steady de novo synthesis of adenosine monophosphate (AMP) explains. Cycling of the 'A' moiety accelerates when the cell's energy state is endangered, another essential domino among the seven required for understanding of the experimental observations. This new domino analysis shows how strategic experimental design and observations in tandem with theory and modeling may identify and resolve important paradoxes. It also highlights the hitherto unexpected role of the 'A' component of ATP. Crown Copyright © 2012. Published by Elsevier B.V. All rights reserved.

  6. Partitioning of Cephalexin in Ionic Liquid Aqueous Two-Phase System Composed of 1-Butyl-3-Methylimidazolium Tetrafluoroborate and ZnSO4

    Directory of Open Access Journals (Sweden)

    Yan Fang Li

    2013-01-01

    Full Text Available Ionic liquid aqueous two-phase system (ILATPS was applied in the extraction and separation of hydrosoluble antibiotics. The partitioning behavior of cephalexin (CEX in 1-butyl-3-methylimidazolium tetrafluoroborate ([Bmim]BF4-ZnSO4 aqueous two-phase system was studied by the partitioning parameter of the extraction efficiency. The effect of the volume of [Bmim]BF4, the concentration of ZnSO4, temperature, pH, and the volume of ZnSO4 solution was discussed concretely. When the volume of [Bmim]BF4 was 2 mL and the concentration of ZnSO4 was 35%, the extraction efficiency of CEX could reach 92.64% with pH unadjusted. The effect of the volume of [Bmim]BF4 on the extraction efficiency was higher than that of the concentration of ZnSO4. The temperature influenced not only the formation of aqueous two-phase system but also the extraction efficiency of CEX. The target was found to be preferentially extracted to the [Bmim]BF4-rich phase at the pH below 4.3. The partition of CEX to the top phase was enhanced by increasing the volume of [Bmim]BF4, the concentration of ZnSO4, and temperature; however, the partition of CEX to the top phase increased by decreasing the pH.

  7. An Experimental Study of Air-Solid Two-Phase Flow in a 90° Bend Using LDV System

    Institute of Scientific and Technical Information of China (English)

    1992-01-01

    The measurements of he mean streamwise and radial velocities,the associated turbulence and the relative particle densities were made in an air-solid two-phase flow in square sectioned(30mm×30mm) 90° vertical to horizontal bend using laser Doppler velocimetry.The radius ratio of the bedn was 2.0.Glass beads of 100um in diameter were employed to form the solid phase.The measurements of air and solid phases were performed separately at the same bulk velocity 19.34m/s,correaponding to a Reynolds number of 3.87×104.The mass ratio of solid to air was 1.6%,The results indicate that the particle trajectories are very close to straight lines.The streamwise velocity profiles for the gas and the solids cross over near the outer wall with the solids having the higher speed.At θ=30° and 45°,particle-wall collisions happen mostly in the region fromθ=30°to θ=75°,and cause a sudden change in solid velocity,The particles tned to move towards the outer wall in 90°bend,The particle concentration near the outer wall is umch higher than that near the inner wall in the bend,and there are few particles in the inside of the bend.The bend leads to apparent phase separation.atθ=45°,the solids concentrate in the half of the duct near the outer wall,After θ=60° the second peak concentration appears,and goes gradually towards the inner wall.

  8. Extraction of spirulina platensis polysaccharide by ethanol/(NH4)2SO4 aqueous two-phase system%乙醇/硫酸铵双水相体系萃取螺旋藻多糖的研究

    Institute of Scientific and Technical Information of China (English)

    刘杨; 冯元琦; 陈美欣; 吴景淳; 黄海根

    2012-01-01

    Extraction of spirulina platensis polysaccharide by ethanol/( NH4 ) 2SO4 aqueous two-phase system(ATPS)was investigated. To remove and recycle the proteins, salting-out precipitation protein was carried out after spirulina platensis cells disruption. Spirulina platensis polysaccharide was extracted by traditional hot water diffusion and the polysaccharide dissolution rate reached 38.44 ± 1. 12mg/g spirulina platensis powder. Spirulina platensis polysaccharide was purified deeply by ethanol/ (NH4)2SO4 ATPS. The yield and enrichment factor of the polysaccharide were 84. 5±1. 45% and 6. 2 respectively,on the condition that the tie line length, volume ratio and pH of ATPS were 42. 9,1. 05 and 7. 0, respectively. The results indicated that spirulina platensis polysaccharide would be purified by a simple, efficient and low cost extraction technology using inexpensive ethanol/ (NH4)2SO4 ATPS.%考察了低分子有机溶剂与无机盐-乙醇/硫酸铵双水相体系萃取螺旋藻多糖的可行性及影响因素.研究结果表明:为除去并有效回收螺旋藻细胞中的蛋白质成分,在藻细胞破碎后进行盐析沉淀蛋白质,再采用传统的热水浸提法,可得到螺旋藻多糖的溶出率为38.44±1.12mg/g干燥粉;通过乙醇/硫酸铵双水相体系的萃取分配,在w(乙醇)=19%,w(硫酸铵)=27.5%(即双水相体系系线长度TLL =42.9),体系相比VR=1.05,pH=7.0时,螺旋藻多糖的收率可达84.5±1.45%,富集因子可达6.2.该研究结果表明廉价的乙醇/硫酸铵双水相萃取螺旋藻多糖将有望开发成为一条简洁、高效、低成本的螺旋藻多糖分离提取工艺.

  9. Anaerobic digestion of food waste through the operation of a mesophilic two-phase pilot scale digester--assessment of variable loadings on system performance.

    Science.gov (United States)

    Grimberg, S J; Hilderbrandt, D; Kinnunen, M; Rogers, S

    2015-02-01

    Single and two-phase operations were compared at mesophilic operating conditions using a digester system consisting of three 5-m(3) reactors treating food waste generated daily within the university campus kitchens. When normalizing the methane production to the daily feedstock characteristics, significantly greater methane was produced during two-phase mesophilic digestion compared to the single-stage operation (methane yield of 380 vs 446-L CH4 kg VS(-1); 359 vs 481-L CH4 kg COD(-1) removed for single vs two stage operation). The fermentation reactor could be maintained reliably even under very low loading rates (0.79±0.16 kg COD m(-3) d(-1)) maintaining a steady state pH of 5.2. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Hydrolysis of triglyceride by the whole cell of Pseudomonas putida 3SK in two-phase batch and continuous reactors systems.

    Science.gov (United States)

    Lee, S Y; Rhee, J S

    1994-08-05

    Batch and continuous hydrolysis of olive oil in an organic-aqueous two-phase system using the live whole cell of Pseudomonas putida 3SK as a source of a lipase is investigated. The strain was not only fully viable and grown well, but also produced extracellular lipase simultaneously. The degree of hydrolysis, depending on olive oil concentration in the solvents, was maximal at 13.5% (w/v) and decreased with the increase of the substrate concentration. At the optimal condition, a degree of hydrolysis higher than 95% was achieved with 24 h at 30 degrees C when the reaction was carried out in a two-phase batch stirred reactor. For long-term operation a continuous stirred reactor was designed. When the reaction was carried out in a continuous stirred reactor, the degree was hydrolysis reached 86% at a dilution rate of 0.2 h(-1). Satisfactory performance of a two-phase bioreactor was obtained in a long-term continous operation, which lasted for at least 30 days by feeding organic solvent containing olive oil and aqueous media separately. (c) 1994 John Wiley & Sons, Inc.

  11. Dependence of chymosin and pepsin partition coefficient with phase volume and polymer pausidispersity in polyethyleneglycol-phosphate aqueous two-phase system.

    Science.gov (United States)

    Spelzini, Darío; Picó, Guillemo; Farruggia, Beatriz

    2006-08-01

    The influence of the phase volume ratio and polymer pausidispersity on chymosin and pepsin partition in polyethylenglycol-phosphate aqueous two-phase systems was studied. Both proteins showed a high affinity for the polyethylenglycol rich phase with a partition coefficient from 20 to 100 for chymosin and from 20 to 180 for pepsin, when the polyethyleneglycol molecular mass in the system varied between 1450 and 8000. The partition coefficient of chymosin was not affected by the volume phase ratio, while the pepsin coefficient showed a significant decrease in its partition coefficient with the increase in the top/bottom phase volume ratio.

  12. Extraction of Tartrazine from Food Colorants by PEG/Salt Aqueous Two-Phase System%PEG/盐双水相萃取食用色素柠檬黄的研究

    Institute of Scientific and Technical Information of China (English)

    姜彬; 李冬梅; 冯志彪

    2014-01-01

    采用PEG/盐双水相体系萃取食用色素柠檬黄。考察了成相物质对柠檬黄吸光度的影响,在此基础上考察了PEG相对分子量、PEG浓度、盐的种类及浓度、p H 对萃取效果的影响,确定了萃取柠檬黄的最佳条件:18% PEG2000,15%(NH4)2SO4,pH 为6。该体系对柠檬黄色萃取效果不受外加无机盐的影响,但表面活性剂的存在对萃取效果有较大影响。%An aqueous two-phase system (ATPS )is presented with polyethylene glycol (PEG )and salt for the extraction of tartrazine in this paper.The extraction of tartrazine in ATPS is investigated. Concentration of (NH4 )2 SO4 and PEG,pH value and other factors are evaluated to determine their effects on the extraction yield of tartrazine.The results show that the extraction yield strongly de-pends on the concentration of PEG and (NH4 )2 SO4 .A high extraction yield around 98% is achieved with the following parameters:(NH4)2SO4 15%,PEG2000 18%,pH 6.It is found that the extrac-tion yield undepends on the additional salt,but the presence of surfactant influences the extraction yield evidently.

  13. ATP monitoring technology for microbial growth control in potable water systems

    Science.gov (United States)

    Whalen, Patrick A.; Whalen, Philip J.; Cairns, James E.

    2006-05-01

    ATP (Adenosine Triphosphate) is the primary energy transfer molecule present in all living biological cells on Earth. ATP cannot be produced or maintained by anything but a living organism, and as such, its measurement is a direct indication of biological activity. The main advantage of ATP as a biological indicator is the speed of the analysis - from collecting the sample to obtaining the result, only minutes are required. The technology to measure ATP is already widely utilized to verify disinfection efficacy in the food industry and is also commonly applied in industrial water processes such as cooling water systems to monitor microbial growth and biocide applications. Research has indicated that ATP measurement technology can also play a key role in such important industries as potable water distribution and biological wastewater treatment. As will be detailed in this paper, LuminUltra Technologies has developed and applied ATP measurement technologies designed for any water type, and as such can provide a method to rapidly and accurately determine the level of biological activity in drinking water supplies. Because of its speed and specificity to biological activity, ATP measurement can play a key role in defending against failing drinking water quality, including those encountered during routine operation and also bioterrorism.

  14. Prediction of liquid-liquid equilibria for polyethylene glycol based aqueous two-phase system by ASOG and UNIFAC method

    Directory of Open Access Journals (Sweden)

    M. Perumalsamy

    2009-03-01

    Full Text Available Liquid-Liquid equilibrium data were obtained for the polyethylene glycol2000(PEG2000-sodium citrate-water system at 298.15, 308.15 and 318.15 K. The effect of temperature on binodal and tie line data was studied and published in a previous article (Murugesan and Perumalsamy, 2005. The interaction parameters of ASOG and UNIFAC models were estimated using the LLE data of PEG2000-sodium citrate-water system and are used to predict the LLE data for PEG6000-sodium citrate-water system at 298.15, 308.15 and 318.15 K (literature data. The predicted LLE data by both ASOG and UNIFAC models showed good agreement with the experimental and literature data.

  15. Cooling the dark energy camera CCD array using a closed-loop two-phase liquid nitrogen system

    Science.gov (United States)

    Cease, H.; DePoy, D.; Derylo, G.; Diehl, H. T.; Estrada, J.; Flaugher, B.; Kuk, K.; Kuhlmann, S.; Lathrop, A.; Schultz, K.; Reinert, R. J.; Schmitt, R. L.; Stefanik, A.; Zhao, A.

    2010-07-01

    The Dark Energy Camera (DECam) is the new wide field prime-focus imager for the Blanco 4m telescope at CTIO. This instrument is a 3 sq. deg. camera with a 45 cm diameter focal plane consisting of 62 2k × 4k CCDs and 12 2k × 2k CCDs and was developed for the Dark Energy Survey that will start operations at CTIO in 2011. The DECam CCD array is inside the imager vessel. The focal plate is cooled using a closed loop liquid nitrogen system. As part of the development of the mechanical and cooling design, a full scale prototype imager vessel has been constructed and is now being used for Multi-CCD readout tests. The cryogenic cooling system and thermal controls are described along with cooling results from the prototype camera. The cooling system layout on the Blanco telescope in Chile is described.

  16. Analysis of partitioning of organic compounds and proteins in aqueous polyethylene glycol-sodium sulfate aqueous two-phase systems in terms of solute-solvent interactions.

    Science.gov (United States)

    da Silva, Nuno R; Ferreira, Luisa A; Madeira, Pedro P; Teixeira, José A; Uversky, Vladimir N; Zaslavsky, Boris Y

    2015-10-09

    Partition behavior of nine small organic compounds and six proteins was examined in poly(ethylene glycol)-8000-sodium sulfate aqueous two-phase systems containing 0.5M osmolyte (sorbitol, sucrose, trehalose, TMAO) and poly(ethylene glycol)-10000-sodium sulfate system, all in 0.01M sodium phosphate buffer, pH 6.8. The differences between the solvent properties of the coexisting phases (solvent dipolarity/polarizability, hydrogen bond donor acidity, and hydrogen bond acceptor basicity) were characterized with solvatochromic dyes using the solvatochromic comparison method. Differences between the electrostatic properties of the phases were determined by analysis of partitioning of sodium salts of dinitrophenylated (DNP-) amino acids with aliphatic alkyl side-chain. It was found out that the partition coefficient of all compounds examined (including proteins) may be described in terms of solute-solvent interactions. The results obtained in the study show that solute-solvent interactions of nonionic organic compounds and proteins in polyethylene glycol-sodium sulfate aqueous two-phase system differ from those in polyethylene glycol-dextran system.

  17. Liquid-liquid equilibrium and partitioning features of bovine trypsin in Ucon 50 HB5100 /sodium citrate aqueous two phase systems

    OpenAIRE

    Tubío, Gisela; Venâncio, Armando; Teixeira, J. A.; Nerli, Bibiana B.; Picó, Guillermo A.

    2008-01-01

    The phase diagrams of Ucon 50-HB-5100, a non-ionic random copolymer of ethylene oxide and propylene oxide (EOPO) and sodium citrate aqueous two-phase systems were determined at different pHs (5.20 and 8.20) and temperatures (5, 20 and 40º C). The binodal curves were determined by refractive index and enzymatic assay of the solution and described using a four-parameter sigmoidal equation, the reliability of the measured tie line compositions was ascertained by correlation equations...

  18. Lactose hydrolysis in aqueous two-phase system by whole-cell {beta}-galactosidase of Kluyveromyces marxianus. Semicontinuous and continuous processes

    Energy Technology Data Exchange (ETDEWEB)

    Tomaska, M. [Slovak Technical Univ., Bratislava (Slovakia). Dept. of Biochemical Technology; Stredansky, M. [Slovak Technical Univ., Bratislava (Slovakia). Dept. of Biochemical Technology; Tomaskova, A. [Slovak Technical Univ., Bratislava (Slovakia). Dept. of Biochemical Technology; Sturdik, E. [Slovak Technical Univ., Bratislava (Slovakia). Dept. of Biochemical Technology

    1995-01-01

    Semicontinuous and continuous hydrolysis of lactose in aqueous two-phase systems (polyethylene glycol 20000/ dextran 40) with whole-cell {beta}-galactosidase of K. marxianus were studied. Both phase polymers had no effect on {beta}-galactosidase activity confined in cells. Good operational stability of the biocatalyst during 55 cycles of semicontinuous process was observed without appreciable decrease in product concentration. Continuous hydrolysis of lactose was performed in the stirred bioreactor, connected with the phase separator. The satisfactory degree of hydrolysis (between 82-88%) and volumetric productivity (21.6 g/l/h) were reached during 72 hours of continuous hydrolysis of 5% (w/w) lactose. (orig.)

  19. LITERATURE REVIEW: HEAT TRANSFER THROUGH TWO-PHASE INSULATION SYSTEMS CONSISTING OF POWDERS IN A CONTINUOUS GAS PHASE

    Science.gov (United States)

    The report, a review of the literature on heat flow through powders, was motivated by the use of fine powder systems to produce high thermal resistivities (thermal resistance per unit thickness). he term "superinsulations" has been used to describe this type of material, which ha...

  20. Existence and stability of weak solutions for a degenerate parabolic system modelling two-phase flows in porous media

    CERN Document Server

    Escher, Joachim; Matioc, Bogdan-Vasile

    2011-01-01

    We prove global existence of nonnegative weak solutions to a degenerate parabolic system which models the interaction of two thin fluid films in a porous medium. Furthermore, we show that these weak solutions converge at an exponential rate towards flat equilibria.

  1. Two-phase flow studies. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kestin, J.; Maeder, P.F.

    1980-08-01

    Progress on the following is reported: literature survey, design of two-phase flow testing facility, design of nozzle loop, thermophysical properties, design manual, and advanced energy conversion systems. (MHR)

  2. Countercurrent Chromatographic Separation of Lipophilic Ascorbic Acid Derivatives and Extract from Kadsura Coccinea Using Hydrophobic Organic-Aqueous Two-Phase Solvent Systems.

    Science.gov (United States)

    Shinomiya, Kazufusa; Li, Heran; Kitanaka, Susumu; Ito, Yoichiro

    2009-01-01

    Countercurrent chromatographic (CCC) separation of lipophilic ascorbic acid derivatives and the crude extract from Kadsura Coccinea was performed using the type-J multilayer coil planet centrifuge with a hydrophobic organic-aqueous two-phase solvent system composed of n-hexane/ethyl acetate/ethanol/aqueous 0.1% trifluoroacetic acid at the volume ratio of (5 : 5 : 6 : 2). The lipophilic ascorbic acid derivatives were separated in the order of L-ascrobyl 2,6-dibutyrate, L-ascorbyl 6-palmitate and L-ascorbyl 6-stearate by eluting the lower phase as the mobile phase, and L-ascorbyl 2,6-dipalmitate was separated by eluting the upper phase at the opposite direction. The above solvent system was then applied to the CCC separation of the extract prepared from K. coccinea. With lower phase mobile, the extract was mainly separated into two peaks corresponding to lignans and triterpenoids accordingly. The HPLC analysis of the fractions showed that the former peak contained Kadsulignan N, Schizandrin H and Neokadsuranin as lignans, and the latter peak, Micranoic acid A, Neokadsuranic acid B and beta-Sitosterol as triterpenoids. The overall results indicate that the hydrophobic organic-aqueous two-phase solvent system used in the present studies was useful for the CCC separation of lignans and triterpenoids present in the natural products.

  3. High resolution of racemic phenylalanine with dication imidazolium-based chiral ionic liquids in a solid-liquid two-phase system.

    Science.gov (United States)

    Huang, Xiaoxia; Wu, Haoran; Wang, Zhixia; Luo, Yingjie; Song, Hang

    2017-01-06

    A novel solid-liquid two-phase system was developed for the chiral separation of racemic phenylalanine with new dication imidazolium-based chiral ionic liquids. Preliminary experiments showed distinct enantioselectivity in amino acid extraction with the novel solid-liquid two-phase system, more L-enantiomer of amino acid cooperatively interacted with ionic liquids and copper ions to be the solid phase. Various factors, including the alkyl chain length of cations of ionic liquids, the amount of copper acetate, the ratio of n(ILs)/n(Cu(2+)), the amount of water and racemic phenylalanine, the resolution time together with the resolution temperature, were systematically investigated for their influence on resolution efficiency. The results showed that, under a certain condition, the enantiomeric excess value and the yield of phenylalanine in liquid phase (mainly containing D-enantiomer) were 67.8% and 96.5%, the enantiomeric excess value and the yield of phenylalanine in solid phase (mainly containing L-enantiomer) were 99.2% and 85.2%. Finally, 2D NMR technology, infrared spectroscopy and molecular simulation method were used to study the interaction mechanism. The results indicated that L-enantiomer of phenylalanine interacts more strongly with chiral ILs and Cu(2+). The novel system has characteristics of free-organic solvent, simple operation, fast separation process and very high resolution efficiency for racemic phenylalanine. This work could provide a new and alternative resolution approach for other chiral separations.

  4. Role of K(ATP)(+) channels in regulation of systemic, pulmonary, and coronary vasomotor tone in exercising swine

    NARCIS (Netherlands)

    D.J.G.M. Duncker (Dirk); H.H. Oei (Hok-Hay); F. Hu; R. Stubenitsky (René); P.D. Verdouw (Pieter)

    2001-01-01

    textabstractThe role of ATP-sensitive K(+) (K(ATP)(+)) channels in vasomotor tone regulation during metabolic stimulation is incompletely understood. Consequently, we studied the contribution of K(ATP)(+) channels to vasomotor tone regulation in the systemic, pulmonary,

  5. Photochemical oxidation of thiophene by O2 in an oil/acetonitrile two-phase extraction system.

    Science.gov (United States)

    Li, Fa-Tang; Zhao, Di-Shun; Li, Hong-Xia; Liu, Rui-Hong

    2008-10-01

    Photochemical oxidation of thiophene in an n-octane/acetonitrile extraction system using O(2) as oxidant was studied. Results obtained here can be used as a reference for desulfurization of gasoline, because thiophene is one of the main components containing sulfur in fluid catalytic cracking gasoline. A 500-W high-pressure mercury lamp was used as a light source for irradiation, and air was introduced by a gas pump to supply O(2). Thiophene dissolved in nopolar n-octane solvent was photodecomposed and removed into the polar acetonitrile phase. The desulfurization rate of thiophene in n-octane was 65.2% under photoirradiation for 5 h under the conditions of air flow at 150 mL min(-1), and V(n-octane):V(acetonitrile) = 1:1. This can be improved to 96.5% by adding 0.15 g Na-ZSM-5 zeolite into the 100-mL reaction system, which is the absorbent for O(2) and thiophene. Under such conditions, the photooxidation kinetics of thiophene with O(2) and Na-ZSM-5 zeolite is first-order with an apparent rate constant of 0.6297 h(-1) and half-time of 1.10 h. The sulfur content can be reduced from 800 microL L(-1) to 28 microL L(-1).

  6. Microstructure Formations in the Two-Phase Region of the Binary Peritectic Organic System TRIS-NPG

    Science.gov (United States)

    Mogeritsch, Johann; Ludwig, Andreas

    2012-01-01

    In order to prepare for an onboard experiment on the International Space Station (ISS), systematic directional solidification experiments with transparent hypoperitectic alloys were carried out at different solidification rates around the critical velocity for morphological stability of both solid phases. The investigations were done in the peritectic region of the binary transparent organic TRIS-NPG system where the formation of layered structures is expected to occur. The transparent appearance of the liquid and solid phase enables real time observations of the dynamic of pattern formation during solidification. The investigations show that frequently occurring nucleation events govern the peritectic solidification morphology which occurs at the limit of morphological stability. As a consequence, banded structures lead to coupled growth even if the lateral growth is much faster compared to the growth in pulling direction.

  7. Polarity, selectivity and performance of hydrophilic organic/salt-containing aqueous two-phase system on counter-current chromatography for polar compounds.

    Science.gov (United States)

    Liu, Dan; Hong, Zhilai; Gao, Mingzhe; Wang, Zhixin; Gu, Ming; Zhang, Xiaozhe; Xiao, Hongbin

    2016-05-27

    The essential attributes of a solvent system for separation polar compounds on CCC are polarity, selectively and performance. Here, hydrophilic organic/salt-containing aqueous two-phase system (HO/S TPS) was evaluated as an alternative solvent system for CCC separation of polar compounds. Polarity measurements based on Rohrschneider-Snyder parameter was developed as quantitative assessing the polarity of HO/S TPS and comparing with an organic/aqueous system. All investigated 1-butanol/ethanol/saturated ammonium sulfate solution/water (BEAsWat) and 1-butanol/ethanol/saturated dipotassium hydrogen phosphate solution/water (BEDhpWat) systems with polarity values of organic phase from 4.5 to 6.8, were more polar than chloroform/methanol/water (1/1/1). The considerable water content of BEAsWat and BEDhpWat (0/1/1/1/) was 45.4 and 42.6% (w%) of hydrophilic organic phase, and 66.4 and 51.2% (w%) of salt-containing aqueous phase, respectively, closed to conventional aqueous two-phase system. Therefore, the polarity of HO/S TPS is in the middle of organic/aqueous and aqueous two-phase system. The LogKC values of twenty four polar compounds as model mixture confirmed that the polarities of HO/S TPSs were matched to that of the polar compounds and shown to be a very selective technique capable of separating positional isomers. Moreover, BEAsWat and BEDhpWat systems can be easily retained in CCC column with suitable elution mode. The hydrodynamic behavior reversion of HO/S TPS on hydrodynamic CCC was observed and was tentatively explained based on the density difference. Finally, caffeoylquinic acid isomers and dihydroxybenzoic acid isomers were successfully separated with HO/S TPS on CCC, respectively. Those results demonstrate that HO/S TPS on CCC is a performant and stable way to separate polar compounds from natural products.

  8. Cloning of Toluene 4-Monooxygenase Genes and Application of Two-Phase System to the Production of the Anticancer Agent, Indirubin.

    Science.gov (United States)

    Wongsaroj, Lampet; Sallabhan, Ratiboot; Dubbs, James M; Mongkolsuk, Skorn; Loprasert, Suvit

    2015-08-01

    Indirubin is a strong inhibitor of several eukaryotic cell signaling pathways and shows promise as a treatment for myelocytic leukemia and Alzheimer's disease. The tmoABCDEF operon, encoding the components of a novel toluene 4-monooxygenase from the paint factory soil isolate, Pseudomonas sp. M4, was cloned and expressed in Escherichia coli. E. coli::pKSR12 expressing the tmo genes was used to develop a two-phase [dioctyl phthalate (DOP)/aqueous medium] culture system that was optimized to obtain maximal yields of indirubin from the starting substrate, indole. DOP was used as the organic phase to solubilize and sequester the toxic indole substrate, making possible the use of high indole concentrations that would otherwise interfere with growth in aqueous media. A 50 % (v/v) DOP two-phase system using tryptophan medium containing 3 mM cysteine, 5 mM indole, and 1 mM isatin yielded 102.4 mg/L of indirubin with no conversion of indole to the less valuable alternate product, indigo.

  9. Chelate-Modified Fenton Reaction for the Degradation of Trichloroethylene in Aqueous and Two-Phase Systems

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, Scott [Univ of KY, dept of chemical and materials engineering; lynch, Andrew [Univ of KY, dept of chemical and materials engineering; Bachas, Leonidas [Univ of KY, Dept of Chemistry; hampson, Steve [Univ of KY Center for Applied Energy Research - KY Research Consortium of Energy and Environment; Ormsbee, Lindelle [Univ of KY Center for Applied Energy Research - KY Research Consortium of Energy and Environment; Bhattacharyya, Dibakar [Univ of KY, dept of chemical and materials engineering

    2008-06-01

    The Standard Fenton reaction has been used for In-Situ Chemical Oxidation (ISCO) of toxic organics in groundwater. However, it requires low pH operating conditions, and thus has limitations for in situ applications. In addition, hydroxyl radicals are rapidly consumed by hydroxyl scavengers found in the subsurface. These problems are alleviated through the chelate-modified Fenton (hydroxyl radical) reaction, which includes the addition of nontoxic chelate (L) such as citrate or gluconic acid. This chelate allows the reaction to take place at bear neutral pH and control hydrogen peroxide consumption by binding to Fe(II), forming an FeL complex. The chelate also binds to Fe(III), preventing its precipitation as ferric hydroxide and thus prevents problems associated with injection well plugging. The rate of TCE dechlorination in chelate-modified Fenton systems is a function of pH, H2O2 concentration, and FE:L ratio. The primary objective of this research is to model and apply this process to the destruction of trichloroethylene (TCE) present in both the aqueous and organic (in the form of droplets) phases. Experimentation proved the chelate-modified Fenton reaction effectively dechlorinates TCE in both the aqueous and organic phases at near-neutral pH. Other focuses of this work include determining the effect of [L]:[Fe] ratios on H2O2 and TCE degradation as well as reusability of the FE citrate solution under repeated H2O2 injections. Generalized models were developed to predict the concentration of TCE in the aqueous phase and TCE droplet radius as a function of time using established hydroxyl radial kinetics and mass transfer relationships.

  10. Study and Implementation of a Two-Phase Interleaved Bidirectional DC/DC Converter for Vehicle and DC-Microgrid Systems

    Directory of Open Access Journals (Sweden)

    Ching-Ming Lai

    2015-09-01

    Full Text Available The objective of this paper is to implement a two-phase, interleaved, bidirectional DC/DC converter topology with an improved voltage conversion ratio for electric vehicle (EV and DC-microgrid systems. In this study, a two-phase interleaved charge-pump topology is introduced to achieve a high voltage conversion ratio with very simple control circuits. In discharge mode, the circuit topology acts as a voltage-multiplier boost converter to achieve a high step-up conversion ratio (48 V to 240 V. In charge mode, the circuit topology acts as a voltage-divider buck converter to achieve a high voltage step-down conversion ratio (240 V to 48 V. The circuit configuration, operating principle, steady-state analysis and the closed-loop control of the proposed converter are presented. Experiments conducted on a laboratory prototype with 500 W power-rating are presented to verify the effectiveness. The maximum efficiency levels in discharge and charge modes are about 97.7% and 98.4% respectively.

  11. Extraction of Theanine from Waste Liquid of Tea Polyphenol Production in Aqueous Two-phase Systems with Cationic and Anionic Surfactants

    Institute of Scientific and Technical Information of China (English)

    ZHANG Junwei; WANG Yan; PENG Qijun

    2013-01-01

    Extraction of theanine from waste liquid of tea polyphenol production was studied in aqueous surfactant two-phase system (ASTP) with cationic suffactant (CTAB) and anionic surfactant (SDS).Results indicate that the region of ASTP is narrow and there is only a two-phase region of cationic surfactant.The increase in concentrations of NaBr and Na2SO4 are beneficial to the formation of ASTP.Theanine concentration in the bottom phase increases with increasing concentration of theanine,whereas the partition coefficient and extraction rate only change a little when the concentration of theanine is above 0.2 g· L-1.With the increase of SDS concentration,the phase ratio and the partition coefficient decrease,while the extraction efficiency of theanine increases and the concentration of theaninc changes a little in the range from 2.4/7.5 to 2.8/7.2 for SDS/CTAB ratio.The temperature has a notable effect on the concentration of theanine in the bottom phase,partition coefficient and extraction rate of theanine.The increase of waste liquid decreases the phase ratio,increases the concentration and extraction rate of theanine in the bottom phase,since the protein and the saccharide enter the bottom phase with theanine.

  12. Knudsen effusion mass spectrometric studies over (USn3+U3Sn7) two-phase region of U-Sn system

    Science.gov (United States)

    Manikandan, P.; Trinadh, V. V.; Bera, Suranjan; Narasimhan, T. S. Lakshmi; Ananthasivan, K.; Joseph, M.; Mudali, U. Kamachi

    2017-08-01

    Vaporisation studies over (USn3+U3Sn7) ;two-phase; field have been carried out by employing Knudsen effusion mass spectrometry (KEMS) in the temperature range of 1050-1226 K. Sn(g) was the species observed in the mass spectrum of the equilibrium vapour phase over the samples (71.5 at% Sn and 73.0 at% Sn). The partial pressure of Sn(g) was measured as a function of temperature over (USn3+U3Sn7) ;two-phase; field and the p-T relation was derived as log (pSn/Pa) = ((-14580 ± 91)/(T/K)) + (8.82 ± 0.08) (1050-1226 K). The vaporisation reaction 3USn3(s) = U3Sn7(s) + 2Sn(g) was evaluated by second law method. The Gibbs energy of formation of USn3(s) was derived as ΔfGm°(U Sn3 , s , T) (±1.8) = -173.4 + 0.055 T (K) (kJ mol-1) (1050-1226 K). The mass spectrometric studies on this system have been carried out for the first time.

  13. Multi-stage mixer-settler planet centrifuge. Preliminary studies on partition of macromolecules with organic-aqueous and aqueous-aqueous two-phase solvent systems.

    Science.gov (United States)

    Ito, Y; Zhang, T Y

    1988-03-11

    A rotary-seal-free planetary centrifuge holds a separation column which consists of multiple partition units (ca. 200) connected in series with transfer tubes. In the cavity of each partition unit the transfer tube extends to form a mixer which vibrates to stir the contents under an oscillating force field generated by the planetary motion of the centrifuge. Consequently, solutes locally introduced at the inlet of the column are subjected to an efficient partition process in each partition unit and separated according to their partition coefficients. The mixer tube equipped with a flexible silicone rubber joint was found to produce excellent results for partition with viscous polymer phase systems. The capability of the method was demonstrated on separation of cytochrome c and lysozyme using a PEG-aqueous dibasic potassium phosphate-aqueous two-phase solvent system.

  14. Genetic engineering of the Fusarium solani pisi lipase cutinase for enhanced partitioning in PEG-phosphate aqueous two-phase systems.

    Science.gov (United States)

    Bandmann, N; Collet, E; Leijen, J; Uhlén, M; Veide, A; Nygren, P A

    2000-04-28

    The Fusarium solani pisi lipase cutinase has been genetically engineered to investigate the influence of C-terminal peptide extensions on the partitioning of the enzyme in PEG-salt based aqueous two-phase bioseparation systems. Seven different cutinase lipase variants were constructed containing various C-terminal peptide extensions including tryptophan rich peptide tags ((WP)(2) and (WP)(4)), positively ((RP)(4)) and negatively ((DP)(4)) charged tags as well as combined tags with tryptophan together with either positively ((WPR)(4)) or negatively ((WPD)(4)) charged amino acids. The modified cutinase variants were stably produced in Escherichia coli as secreted to the periplasm from which they were efficiently purified by IgG-affinity chromatography employing an introduced N-terminal IgG-binding ZZ affinity fusion partner present in all variants. Partitioning experiments performed in a PEG 4000/sodium phosphate aqueous two-phase system showed that for variants containing either (WP)(2) or (WP)(4) peptide extensions, 10- to 70-fold increases in the partitioning to the PEG rich top-phase were obtained, when compared to the wild type enzyme. An increased partitioning was also seen for cutinase variants tagged with both tryptophans and charged amino acids, whereas the effect of solely charged peptide extensions was relatively small. In addition, when performing partitioning experiments from cell disintegrates, the (WP)(4)-tagged cutinase showed a similarly high PEG-phase partitioning, indicating that the effect from the peptide tag was unaffected by the background of the host proteins. Taken together, the results show that the partitioning of the recombinantly produced cutinase model enzyme could be significantly improved by relatively minor genetic engineering and that the effects observed for purified proteins are retained also in an authentic whole cell disintegrate system. The results presented should be of general interest also for the improvement of the

  15. Transfer RNA is an essential component of the ubiquitin- and ATP-dependent proteolytic system

    Energy Technology Data Exchange (ETDEWEB)

    Ciechanover, A.; Wolin, S.L.. Steitz, J.A.; Lodish, H.F.

    1985-03-01

    Protein degradation via the nonlysosomal ATP-dependent pathway in rabbit reticulocytes involves a number of components. In the initial event, ubiquitin, an abundant 76-residue polypeptide, becomes covalently linked to the protein substrate in an ATP-requiring reaction. Once marked in this way, the conjugated protein is proteolyzed in a reaction that also requires ATP. Here the authors show that tRNA is another essential component of the system. Ribonucleases strongly inhibit the ubiquitin- and ATP-dependent degradation of /sup 125/I-labeled bovine serum albumin in the reticulocyte system in vitro. RNAs extracted from fractions of the reticulocyte extract or from mouse cells restore proteolytic activity. When the RNA is fractionated by gel electrophoresis, only the tRNA fraction is active in restoring proteolysis. Furthermore, pure mouse tRNA/sup His/, isolated by immunoprecipitation with patient autoimmune sera, restores the proteolytic activity. The possibility that the level of uncharged tRNA in mammalian cells regulates the ubiquitin- and ATP-dependent proteolytic system is discussed.

  16. An alternative method to isolate protease and phospholipase A2 toxins from snake venoms based on partitioning of aqueous two-phase systems

    Directory of Open Access Journals (Sweden)

    GN Gómez

    2012-01-01

    Full Text Available Snake venoms are rich sources of active proteins that have been employed in the diagnosis and treatment of health disorders and antivenom therapy. Developing countries demand fast economical downstream processes for the purification of this biomolecule type without requiring sophisticated equipment. We developed an alternative, simple and easy to scale-up method, able to purify simultaneously protease and phospholipase A2 toxins from Bothrops alternatus venom. It comprises a multiple-step partition procedure with polyethylene-glycol/phosphate aqueous two-phase systems followed by a gel filtration chromatographic step. Two single bands in SDS-polyacrylamide gel electrophoresis and increased proteolytic and phospholipase A2 specific activities evidence the homogeneity of the isolated proteins.

  17. Separation of clavulanic acid from fermented broth of amino acids by an aqueous two-phase system and ion-exchange adsorption.

    Science.gov (United States)

    da Silva, Clovis Sacardo; Cuel, Maressa Fabiano; Barreto, Verônica Orlandin; Kwong, Wu Hong; Hokka, Carlos O; Barboza, M

    2012-02-15

    The clavulanic acid is a substance which inhibits the β-lactamases used with penicillins for therapeutic treatment. After the fermentation, by-products of low molecular weight such as amino acids lysine, histidine, proline and tyrosine are present in the fermented broth. To remove these impurities the techniques of extraction by an aqueous two-phase system of 17% polyethylene glycol molecular weight 600 and 15% potassium phosphate were used for a partial purification. A subsequent ion-exchange adsorption was used for the recuperation of the clavulanic acid of the top phase and purification getting a concentration factor of 2 and purification of 100% in relation to the amino acids lysine, histidine, proline and tyrosine.

  18. Surfactant-coated Candida rugosa Lipase as Catalyst for Hydrolysis of Olive Oil in Solvent-Free Two-Phase System

    Institute of Scientific and Technical Information of China (English)

    宋宝东; 丁辉; 吴金川; HayashiY.; TalukderMMR; 王世昌

    2003-01-01

    The surfactant-coated Candida rugosa lipase was used as catalyst for hydrolysis of olive oil in two-phase system consisting of olive oil and phosphate buffer without organic solvent. For both the coated and native lipases,the optimal buffer/oil volume ratio of 1.0, aqueous pH 6.8 and reaction temperature 30℃ were determined. The maximum activity of the coated lipase was ca 1.3 times than that of the native lipase. The half-life of the coated lipase in olive oil and the native lipase in phosphate buffer was ca 9 h and 12 h, and the final residual activity was 27% and 20% of their initial values, respectively. The final substrate conversion by the coated lipase was ca 20% higher than that of the native lipase.

  19. Calculation of liquid-liquid equilibrium of aqueous two-phase systems using a chemical-theory-based excess Gibbs energy model

    Directory of Open Access Journals (Sweden)

    Pessôa Filho P. A.

    2004-01-01

    Full Text Available Mixtures containing compounds that undergo hydrogen bonding show large deviations from ideal behavior. These deviations can be accounted for through chemical theory, according to which the formation of a hydrogen bond can be treated as a chemical reaction. This chemical equilibrium needs to be taken into account when applying stability criteria and carrying out phase equilibrium calculations. In this work, we illustrate the application of the stability criteria to establish the conditions under which a liquid-phase split may occur and the subsequent calculation of liquid-liquid equilibrium using a chemical-theory-modified Flory-Huggins equation to describe the non ideality of aqueous two-phase systems composed of poly(ethylene glycol and dextran. The model was found to be able to correlate ternary liquid-liquid diagrams reasonably well by simple adjustment of the polymer-polymer binary interaction parameter.

  20. The tendency of smooth and rough Salmonella typhimurium bacteria and lipopolysaccharide to hydrophobic and ionic interaction, as studied in aqueous polymer two-phase systems.

    Science.gov (United States)

    Magnusson, K E; Stendahl, O; Tagesson, C; Edebo, L; Johansson, G

    1977-06-01

    In aqueous two-phase system, the partition of bacteria and lipopolysaccharide from a rough (R) strain (Rd-mutant) of Salmonella typhimurium is influenced by polymers with covalently linked hydrophobic groups indicating hydrophobic structures accessible at the cell surface. Furthermore, the partition of the R bacteria is influenced by a number of inorganic positive and negative ions, presumably as a consequence of interaction with negatively charged surface structures. In contrast, smooth (S) bacteria and lipopolysaccharide from the parent strain do not seem to participate in either hydrophobic or charge interaction indicating extensive hydrophilicity without charge. Thus, the S-specific polysaccharide side chain of S. typhimurium might serve the purpose of blindfolding aspecific host defence mechanisms dependent on hydrophobicity and charge. On the contrary, the R bacteria and R lipopolysaccharide have physico-chemical properties which predispose to interaction with several types of cells, organelles and molecules.

  1. Determination of sunset yellow and tartrazine in food samples by combining ionic liquid-based aqueous two-phase system with high performance liquid chromatography.

    Science.gov (United States)

    Sha, Ou; Zhu, Xiashi; Feng, Yanli; Ma, Weixing

    2014-01-01

    We proposed a simple and effective method, by coupling ionic liquid-based aqueous two-phase systems (IL-ATPSs) with high performance liquid chromatography (HPLC), for the analysis of determining tartrazine and sunset yellow in food samples. Under the optimized conditions, IL-ATPSs generated an extraction efficiency of 99% for both analytes, which could then be directly analyzed by HPLC without further treatment. Calibration plots were linear in the range of 0.01-50.0 μg/mL for both Ta and SY. The limits of detection were 5.2 ng/mL for Ta and 6.9 ng/mL for SY. This method proves successful for the separation/analysis of tartrazine and sunset yellow in soft drink sample, candy sample, and instant powder drink and leads to consistent results as obtained from the Chinese national standard method.

  2. Determination of Sunset Yellow and Tartrazine in Food Samples by Combining Ionic Liquid-Based Aqueous Two-Phase System with High Performance Liquid Chromatography

    Directory of Open Access Journals (Sweden)

    Ou Sha

    2014-01-01

    Full Text Available We proposed a simple and effective method, by coupling ionic liquid-based aqueous two-phase systems (IL-ATPSs with high performance liquid chromatography (HPLC, for the analysis of determining tartrazine and sunset yellow in food samples. Under the optimized conditions, IL-ATPSs generated an extraction efficiency of 99% for both analytes, which could then be directly analyzed by HPLC without further treatment. Calibration plots were linear in the range of 0.01–50.0 μg/mL for both Ta and SY. The limits of detection were 5.2 ng/mL for Ta and 6.9 ng/mL for SY. This method proves successful for the separation/analysis of tartrazine and sunset yellow in soft drink sample, candy sample, and instant powder drink and leads to consistent results as obtained from the Chinese national standard method.

  3. Releasing intracellular product to prepare whole cell biocatalyst for biosynthesis of Monascus pigments in water-edible oil two-phase system.

    Science.gov (United States)

    Hu, Minglue; Zhang, Xuehong; Wang, Zhilong

    2016-11-01

    Selective releasing intracellular product in Triton X-100 micelle aqueous solution to prepare whole cell biocatalyst is a novel strategy for biosynthesis of Monascus pigments, in which cell suspension culture exhibits some advantages comparing with the corresponding growing cell submerged culture. In the present work, the nonionic surfactant Triton X-100 was successfully replaced by edible plant oils for releasing intracellular Monascus pigments. High concentration of Monascus pigments (with absorbance nearly 710 AU at 470 nm in the oil phase, normalized to the aqueous phase volume approximately 142 AU) was achieved by cell suspension culture in peanut oil-water two-phase system. Furthermore, the utilization of edible oil as extractant also fulfills the demand for application of Monascus pigments as natural food colorant.

  4. Solubilization of proteins in aqueous two-phase extraction through combinations of phase-formers and displacement agents.

    Science.gov (United States)

    Kress, Christian; Sadowski, Gabriele; Brandenbusch, Christoph

    2017-03-01

    The aqueous two-phase extraction (ATPE) of therapeutic proteins is a promising separation alternative to cost-intensive chromatography, still being the workhorse of nowadays downstream processing. As shown in many publications, using NaCl as displacement agent in salt-polymer ATPE allows for a selective purification of the target protein immunoglobulin G (IgG) from human serum albumin (HSA, represents the impurity). However a high yield of the target protein is only achievable as long as the protein is stabilized in solution and not precipitated. In this work the combined influence of NaCl and polyethylene glycol (Mw=2000g/mol) on the IgG-IgG interactions was determined using composition gradient multi-angle light scattering (CG-MALS) demonstrating that NaCl induces a solubilization of IgG in polyethylene glycol 2000 solution. Moreover it is shown that the displacement agent NaCl has a significant and beneficial influence on the IgG solubility in polyethyleneglycol2000-citrate aqueous two-phase system (ATPS) which can also be accessed by these advanced B22 measurements. By simultaneous consideration of IgG solubility data with results of the ATPS phase behavior (especially volume fraction of the respective phases) allows for the selection of process tailored ATPS including identification of the maximum protein feed concentration. Through this approach an ATPS optimization is accessible providing high yields and selectivity of the target protein (IgG).

  5. Copper(II) ions interactions in the systems with triamines and ATP. Potentiometric and spectroscopic studies.

    Science.gov (United States)

    Hoffmann, S K; Goslar, J; Bregier-Jarzebowska, R; Gasowska, A; Zalewska, A; Lomozik, L

    2017-09-09

    The mode of interaction and thermodynamic stability of complexes formed in binary and ternary Cu(II)/ATP/triamines systems were studied using potentiometric and spectroscopic (NMR, EPR, UV-Vis) methods. It was found that in binary metal-free systems ATP/HxPA species are formed (PA: Spd=spermidine or 3,3-tri=1,7-diamino-4-azaheptane) where the phosphate groups from nucleotides are preferred negative centers and protonated amine groups of amines are positive centers of reaction. In the ternary systems Cu/ATP/Hx(PA) as well as Cu/(ATP)(PA) species are formed. The type of the formed Cu(II) complexes depends on pH of the solution. For a low pH value the complexation appears between Cu(II) and ATP molecules via oxygen atoms of phosphate groups. For a very high pH value, where ATP is hydrolyzed, the Cu(II) ions are bound to the nitrogen atoms of polyamine molecules. We did not detect any direct coordination of the N7 nitrogen atom of adenosine to Cu(II) ions. It means that the CuN7 interaction is an indirect type and can be due to noncovalent interplay including water molecule. EPR studies were performed at glassy state (77K) after a fast freezing both for binary and ternary systems. The glassy state EPR spectra do not reflect species identified in titration studies indicating significant effect of rapid temperature decrease on equilibrium of Cu(II) complexes. We propose the molecular structure of all the studied complexes at the glassy state deduced from EPR and optical spectroscopy results. Copyright © 2017 Elsevier Inc. All rights reserved.

  6. 手性药物扁桃酸的双水相分离%Study on partition of D(-)-mandelic acid in aqueous two-phase systems

    Institute of Scientific and Technical Information of China (English)

    许小平; 李忠琴; 陈杰波

    2004-01-01

    Studies on the partition of D (-)-mandelic acid were performed in polyethylene glycol (PEG) with molecular masses of 2000, 4000, 6000, 10000, 20000- ammonium sulfate systems. The effect of various parameters such as molecular mass of PEG, phase composition, pH of the system and temperature were investigated in this work. The results indicate that the molecular mass of PEG is a key factor affecting the partitioning behaviors of D(-)-mandelic acid in the PEG -(NH4)2SO4 systems. The influence of pH on the partition shows that the partition coefficient of D(-)-mandelic acid decreases with the increase of pH value. D(-)-mandelic acid partition is only slightly influenced by the temperature. All these indicate that the aqueous two-phase is a very suitable alternative system for the separation of D(-)-mandelic acid.%采用聚乙二醇-硫酸铵双水相系统分离手性药物扁桃酸.研究了聚乙二醇分子量、相组成、pH值和温度对扁桃酸分离的影响.结果表明,聚乙二醇分子量对双水相分离扁桃酸的影响最大;温度对扁桃酸的分离几乎没有影响;随pH增大,扁桃酸分配系数减少.

  7. The influence of molecular weight of polyethylene glycol on separation and purification of pectinases from Penicillium cyclopium in aqueous two-phase system

    Directory of Open Access Journals (Sweden)

    Prodanović Jelena M.

    2008-01-01

    Full Text Available In this study the possibility of the partitioning and purification of pectinases from Penicillium cyclopium by their partitioning in polymer/polymer and polymer/salt aqueous two-phase systems was investigated. In the system with 10% (w/w polyethylene glycol 1500/5% (w/w dextran 500 000/85% (w/w crude enzyme, the highest values for partitioning parameters were achieved - the partition coefficient was 2.11, followed by the top phase yield of 85.68% and purification factor 1.28 for the endo-pectinase activity. The partition coefficient, yield in the top phase and purification factor for the exo-pectinase activity in the same system were 1.89, 84.28% and 3.82, respectively. In the system with 10% (w/w polyethylene glycol 6000/15% (w/w (NH42SO4/75% (w/w crude enzyme purification factor 37.85 for exo-pectinase, and 19.52 for endo-pectinase in the bottom phase were obtained.

  8. Progress on the study of mechanism and partition behavior of papain in affinity aqueous two-phase systems%木瓜蛋白酶在亲和双水相系统中的分配行为及机制研究进展

    Institute of Scientific and Technical Information of China (English)

    张海德; 王伟涛; 蒋欣欣

    2013-01-01

    The separation methods of papain such as ultrafiltration, salt deposition, solvent extraction, affinity chromatography, aqueous two - phase extraction, affinity aqueous two-phase extraction and so on are evaluated. High purity papain can be expected to obtain by metal chelating affinity aqueous two-phase system (ATPS) technology, but the mechanism and partition behavior of papain in this system are not clear. It is important to study the interactions between papain and different metal ion affinity phase-separating agent, the adsorption kinetics model of papain in ATPS and the physical structure characterization and molecular simulation of the enzyme affinity adsorbent. Metal chelating affinity ATPS technology based on papain separation, will vigorously promote the development of papain industrialization and it has stimulative effect on the development of aqueous two-phase extraction technology.%  本文查阅相关文献,对木瓜蛋白酶传统提取方法(超滤法、盐析法、有机溶剂法、亲和层析法)及一些新兴的提取方法如双水相萃取法、亲和双水相法作了简要综述。利用金属螯合亲和双水相分配系统,能有效获得高纯度木瓜蛋白酶,但木瓜蛋白酶与亲和成相剂的相互作用及其分配行为与机制尚不清楚。研究木瓜蛋白酶与不同金属离子亲和成相剂之间的相互作用和吸附动力学模型;对酶的亲和结合物进行物理表征和分子模拟。阐明木瓜蛋白酶与不同金属离子亲和成相剂之间的亲和作用原理。将双水相萃取技术和亲和分配技术相融合,提出基于木瓜蛋白酶的金属螯合亲和双水相分配技术,该技术有望大力推动木瓜蛋白酶工业化高效制备的发展。

  9. Aqueous two-phase system cold-set gelation using natural and recombinant probiotic lactic acid bacteria as a gelling agent.

    Science.gov (United States)

    Léonard, Lucie; Husson, Florence; Langella, Philippe; Châtel, Jean-Marc; Saurel, Rémi

    2016-05-01

    The present study aimed to entrap probiotic lactic acid bacteria (LAB) in a sodium alginate and sodium caseinate aqueous two-phase gel system. The natural acidifying properties of two therapeutic probiotic LAB were exploited to liberate calcium ions progressively from calcium carbonate (CaCO3), which caused the gelation of the co-existing phases. Bi-biopolymeric matrix gelation of GDL/CaCO3 or LAB/CaCO3 was monitored by dynamic rheological measurements, and the final gels were characterized by frequency dependence measurements and confocal laser scanning microscopy. Weak to strong gels were formed with an elastic modulus G' from 10 to 1.000Pa, respectively. After cold-set gelation of our system, confocal laser scanning microscopy showed spherical protein microdomains trapped within a calcium alginate network. LAB cells were stained to study their partition in the self-gelling matrices. Our LAB strains showed two different behaviors, which may relate to the exopolysaccharide production: (i) Lactobacillus plantarum CNRZ1997 cells were found mainly in continuous alginate networks, whereas (ii) Lactococcus lactis cells were localized in protein microdomains. This alginate-caseinate phase-separated system that was self-gelled by LAB cells may be an innovative approach for immobilizing and protecting LAB cells.

  10. Purification and characterization of polyphenol oxidase from waste potato peel by aqueous two-phase extraction.

    Science.gov (United States)

    Niphadkar, Sonali S; Vetal, Mangesh D; Rathod, Virendra K

    2015-01-01

    Potato peel from food industrial waste is a good source of polyphenol oxidase (PPO). This work illustrates the application of an aqueous two-phase system (ATPS) for the extraction and purification of PPO from potato peel. ATPS was composed of polyethylene glycol (PEG) and potassium phosphate buffer. Effect of different process parameters, namely, PEG, potassium phosphate buffer, NaCl concentration, and pH of the system, on partition coefficient, purification factor, and yield of PPO enzyme were evaluated. Response surface methodology (RSM) was utilized as a statistical tool for the optimization of ATPS. Optimized experimental conditions were found to be PEG1500 17.62% (w/w), potassium phosphate buffer 15.11% (w/w), and NaCl 2.08 mM at pH 7. At optimized condition, maximum partition coefficient, purification factor, and yield were found to be 3.7, 4.5, and 77.8%, respectively. After partial purification of PPO from ATPS, further purification was done by gel chromatography where its purity was increased up to 12.6-fold. The purified PPO enzyme was characterized by sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE), followed by Km value 3.3 mM, and Vmax value 3333 U/mL, and enzyme stable ranges for temperature and pH of PPO were determined. These results revealed that ATPS would be an attractive option for obtaining purified PPO from waste potato peel.

  11. Response Surface Methodology Modelling of an Aqueous Two-Phase System for Purification of Protease from Penicillium candidum (PCA 1/TT031 under Solid State Fermentation and Its Biochemical Characterization

    Directory of Open Access Journals (Sweden)

    Amaal M. Alhelli

    2016-11-01

    Full Text Available Penicillium candidum (PCA 1/TT031 synthesizes different types of extracellular proteases. The objective of this study is to optimize polyethylene glycol (PEG/citrate based on an aqueous two-phase system (ATPS and Response Surface Methodology (RSM to purify protease from Penicillium candidum (PCA 1/TT031. The effects of different PEG molecular weights (1500–10,000 g/mol, PEG concentration (9%–20%, concentrations of NaCl (0%–10% and the citrate buffer (8%–16% on protease were also studied. The best protease purification could be achieved under the conditions of 9.0% (w/w PEG 8000, 5.2% NaCl, and 15.9% sodium citrate concentration, which resulted in a one-sided protease partitioning for the bottom phase with a partition coefficient of 0.2, a 6.8-fold protease purification factor, and a yield of 93%. The response surface models displayed a significant (p ≤ 0.05 response which was fit for the variables that were studied as well as a high coefficient of determination (R2. Similarly, the predicted and observed values displayed no significant (p > 0.05 differences. In addition, our enzyme characterization study revealed that Penicillium candidum (PCA 1/TT031 produced a slight neutral protease with a molecular weight between 100 and 140 kDa. The optimal activity of the purified enzyme occurred at a pH of 6.0 and at a temperature of 50 °C. The stability between different pH and temperature ranges along with the effect of chemical metal ions and inhibitors were also studied. Our results reveal that the purified enzyme could be used in the dairy industry such as in accelerated cheese ripening.

  12. Response Surface Methodology Modelling of an Aqueous Two-Phase System for Purification of Protease from Penicillium candidum (PCA 1/TT031) under Solid State Fermentation and Its Biochemical Characterization

    Science.gov (United States)

    Alhelli, Amaal M.; Abdul Manap, Mohd Yazid; Mohammed, Abdulkarim Sabo; Mirhosseini, Hamed; Suliman, Eilaf; Shad, Zahra; Mohammed, Nameer Khairulla; Meor Hussin, Anis Shobirin

    2016-01-01

    Penicillium candidum (PCA 1/TT031) synthesizes different types of extracellular proteases. The objective of this study is to optimize polyethylene glycol (PEG)/citrate based on an aqueous two-phase system (ATPS) and Response Surface Methodology (RSM) to purify protease from Penicillium candidum (PCA 1/TT031). The effects of different PEG molecular weights (1500–10,000 g/mol), PEG concentration (9%–20%), concentrations of NaCl (0%–10%) and the citrate buffer (8%–16%) on protease were also studied. The best protease purification could be achieved under the conditions of 9.0% (w/w) PEG 8000, 5.2% NaCl, and 15.9% sodium citrate concentration, which resulted in a one-sided protease partitioning for the bottom phase with a partition coefficient of 0.2, a 6.8-fold protease purification factor, and a yield of 93%. The response surface models displayed a significant (p ≤ 0.05) response which was fit for the variables that were studied as well as a high coefficient of determination (R2). Similarly, the predicted and observed values displayed no significant (p > 0.05) differences. In addition, our enzyme characterization study revealed that Penicillium candidum (PCA 1/TT031) produced a slight neutral protease with a molecular weight between 100 and 140 kDa. The optimal activity of the purified enzyme occurred at a pH of 6.0 and at a temperature of 50 °C. The stability between different pH and temperature ranges along with the effect of chemical metal ions and inhibitors were also studied. Our results reveal that the purified enzyme could be used in the dairy industry such as in accelerated cheese ripening. PMID:27845736

  13. Validation and comparison of two-phase flow modeling capabilities of CFD, sub channel and system codes by means of post-test calculations of BFBT transient tests

    Energy Technology Data Exchange (ETDEWEB)

    Jaeger, Wadim; Manes, Jorge Perez; Imke, Uwe; Escalante, Javier Jimenez; Espinoza, Victor Sanchez, E-mail: victor.sanchez@kit.edu

    2013-10-15

    Highlights: • Simulation of BFBT turbine and pump transients at multiple scales. • CFD, sub-channel and system codes are used for the comparative study. • Heat transfer models are compared to identify difference between the code predictions. • All three scales predict results in good agreement to experiment. • Sub cooled boiling models are identified as field for future research. -- Abstract: The Institute for Neutron Physics and Reactor Technology (INR) at the Karlsruhe Institute of Technology (KIT) is involved in the validation and qualification of modern thermo hydraulic simulations tools at various scales. In the present paper, the prediction capabilities of four codes from three different scales – NEPTUNE{sub C}FD as fine mesh computational fluid dynamics code, SUBCHANFLOW and COBRA-TF as sub channels codes and TRACE as system code – are assessed with respect to their two-phase flow modeling capabilities. The subject of the investigations is the well-known and widely used data base provided within the NUPEC BFBT benchmark related to BWRs. Void fraction measurements simulating a turbine and a re-circulation pump trip are provided at several axial levels of the bundle. The prediction capabilities of the codes for transient conditions with various combinations of boundary conditions are validated by comparing the code predictions with the experimental data. In addition, the physical models of the different codes are described and compared to each other in order to explain the different results and to identify areas for further improvements.

  14. Water-head-driven microfluidic oscillators for autonomous control of periodic flows and generation of aqueous two-phase system droplets.

    Science.gov (United States)

    Dang, Van Bac; Kim, Sung-Jin

    2017-01-17

    Generating periodic flows with an oscillator driven only by water-head pressure has potential for the operation of microfluidic systems without any dynamic off-chip controllers. However, its operational characteristic is not well understood due to complex dynamic interactions of the microfluidic components. Here, we focus on the mechanism of a water-head-driven oscillator and analyze the functions of its flow-switching period (T) and flow rate (Q) in a wide range (0.1 s-5.9 h and 2 μL min(-1)-2 mL min(-1)). We show linear control of T and Q by their corresponding fluidic resistors even with the complex and nonlinear relation of the microfluidic components. This allows independent regulation of T and Q within their operational ranges but we found the two parameters mutually constrain their ranges via fluidic resistance. Also, we characterize the control of T by water-head pressure and present operational ranges of input water-head pressure decrease with increasing output water-head pressure. To show its utility, we apply the oscillator to generate droplets with low interfacial tension aqueous two-phase systems. Our study would be useful and provide the foundation for various functions of water-head-driven microfluidic circuits.

  15. Rapid, highly efficient extraction and purification of membrane proteins using a microfluidic continuous-flow based aqueous two-phase system.

    Science.gov (United States)

    Hu, Rui; Feng, Xiaojun; Chen, Pu; Fu, Meng; Chen, Hong; Guo, Lin; Liu, Bi-Feng

    2011-01-07

    Membrane proteins play essential roles in regulating various fundamental cellular functions. To investigate membrane proteins, extraction and purification are usually prerequisite steps. Here, we demonstrated a microfluidic aqueous PEG/detergent two-phase system for the purification of membrane proteins from crude cell extract, which replaced the conventional discontinuous agitation method with continuous extraction in laminar flows, resulting in significantly increased extraction speed and efficiency. To evaluate this system, different separation and detection methods were used to identify the purified proteins, such as capillary electrophoresis, SDS-PAGE and nano-HPLC-MS/MS. Swiss-Prot database with Mascot search engine was used to search for membrane proteins from random selected bands of SDS-PAGE. Results indicated that efficient purification of membrane proteins can be achieved within 5-7s and approximately 90% of the purified proteins were membrane proteins (the highest extraction efficiency reported up to date), including membrane-associated proteins and integral membrane proteins with multiple transmembrane domains. Compared to conventional approaches, this new method had advantages of greater specific surface area, minimal emulsification, reduced sample consumption and analysis time. We expect the developed method to be potentially useful in membrane protein purifications, facilitating the investigation of membrane proteomics.

  16. Investigation of the thermal performance of a vertical two-phase closed thermosyphon as a passive cooling system for a nuclear reactor spent fuel storage pool

    Energy Technology Data Exchange (ETDEWEB)

    Kusuma, Mukhsinun Hadi; Putra, Nandy; Imawan, Ficky Augusta [Heat Transfer Laboratory, Department of Mechanical Engineering Universitas Indonesia, Kampus (Indonesia); Antariksawan, Anhar Riza [Centre for Nuclear Reactor Safety and Technology, National Nuclear Energy Agency of Indonesia (BATAN), Kawasan Puspiptek Serpong (Indonesia)

    2017-04-15

    The decay heat that is produced by nuclear reactor spent fuel must be cooled in a spent fuel storage pool. A wickless heat pipe or a vertical two-phase closed thermosyphon (TPCT) is used to remove this decay heat. The objective of this research is to investigate the thermal performance of a prototype model for a large-scale vertical TPCT as a passive cooling system for a nuclear research reactor spent fuel storage pool. An experimental investigation and numerical simulation using RELAP5/MOD 3.2 were used to investigate the TPCT thermal performance. The effects of the initial pressure, filling ratio, and heat load were analyzed. Demineralized water was used as the TPCT working fluid. The cooled water was circulated in the water jacket as a cooling system. The experimental results show that the best thermal performance was obtained at a thermal resistance of 0.22°C/W, the lowest initial pressure, a filling ratio of 60%, and a high evaporator heat load. The simulation model that was experimentally validated showed a pattern and trend line similar to those of the experiment and can be used to predict the heat transfer phenomena of TPCT with varying inputs.

  17. Pressure Loss across Tube Bundles in Two-phase Flow

    Energy Technology Data Exchange (ETDEWEB)

    Sim, Woo Gun; Banzragch, Dagdan [Hannam Univ., Daejon (Korea, Republic of)

    2016-03-15

    An analytical model was developed by Sim to estimate the two-phase damping ratio for upward two-phase flow perpendicular to horizontal tube bundles. The parameters of two-phase flow, such as void fraction and pressure loss evaluated in the model, were calculated based on existing experimental formulations. However, it is necessary to implement a few improvements in the formulations for the case of tube bundles. For the purpose of the improved formulation, we need more information about the two-phase parameters, which can be found through experimental test. An experiment is performed with a typical normal square array of cylinders subjected to the two-phase flow of air-water in the tube bundles, to calculate the two-phase Euler number and the two-phase friction multiplier. The pitch-to-diameter ratio is 1.35 and the diameter of cylinder is 18mm. Pressure loss along the flow direction in the tube bundles is measured with a pressure transducer and data acquisition system to calculate the two-phase Euler number and the two-phase friction multiplier. The void fraction model by Feenstra et al. is used to estimate the void fraction of the two-phase flow in tube bundles. The experimental results of the two phase friction multiplier and two-phase Euler number for homogeneous and non-homogeneous two-phase flows are compared and evaluated against the analytical results given by Sim's model.

  18. Enhanced thermionic emission properties in textured two-phase LaB{sub 6}–BaB{sub 6} system prepared by spark plasma sintering

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Shen Lin, E-mail: shenlinz@sina.com [College of Mathematics and Physics, Jinggangshan University, Jian 343409 (China); Shanghai Key Laboratory of Special Artificial Microstructure and Pohl Institute of Solid State Physics and School of Physics Science and Engineering, Tongji University, Shanghai 200092 (China); State Key Laboratory of Theoretical Physics, Institute of Theoretical Physics, Chinese Academy of Sciences, Beijing 100190 (China); Zhang, Jiu Xing, E-mail: zjiuxing@hfut.edu.cn [School of Materials Science and Engineering, Hefei University of Technology, Hefei 230009 (China); Bao, Li Hong [Inner Mongolia Key Laboratory for Physics and Chemistry of Functional Materials, Inner Mongolia Normal University, Hohhot 010022 (China); Yu, Xiao Guang; Hu, Qiang Lin; Hu, Dong Qiang [College of Mathematics and Physics, Jinggangshan University, Jian 343409 (China)

    2014-10-25

    Graphical abstract: Room temperature XRD patterns of the nominal composition (La{sub 0.6}Ba{sub 0.4})B{sub 6} synthesized by SPS at 1400 °C for 5 min under 50 MPa. The XRD patterns reveal that the (La{sub 0.6}Ba{sub 0.4})B{sub 6} is a two-phase mixture of LaB{sub 6} and BaB{sub 6}. The inset is a macroscopic picture of the obtained (La{sub 0.6}Ba{sub 0.4})B{sub 6}. - Highlights: • (La{sub 0.6}Ba{sub 0.4})B{sub 6} has been successfully prepared by spark plasma sintering. • The obtained (La{sub 0.6}Ba{sub 0.4})B{sub 6} compound is a two-phase mixture of LaB{sub 6} and BaB{sub 6}. • The (0 0 1) texture is favorable for the decrease of work function. • The addition of BaB{sub 6} to LaB{sub 6} improves the electron emission performance. • (La{sub 0.6}Ba{sub 0.4})B{sub 6} is shown to be promising candidate for cathode applications. - Abstract: Structure, crystallographic orientation, and thermionic emission properties of the two-phase LaB{sub 6}–BaB{sub 6} system fabricated by a combined process of evaporation–condensation and spark plasma sintering (SPS) were investigated systematically. The powder X-ray diffraction (XRD) reveals that the obtained nominal composition (La{sub 0.6}Ba{sub 0.4})B{sub 6} compound exhibits coexistence of two isostructural phases of LaB{sub 6} and BaB{sub 6}. The electron backscatter diffraction (EBSD) confirms that the surface of the (La{sub 0.6}Ba{sub 0.4})B{sub 6} forms a clear (0 0 1) texture, which favors reduction in work function. Thermionic emission properties were measured in the temperature range between 1500 and 1873 K. The results indicated that the (La{sub 0.6}Ba{sub 0.4})B{sub 6} emitter displayed a low work function of 1.95 eV, and a high zero field emission current density of 10 A cm{sup −2} at 1773 K. Compared to the reported LaB{sub 6} and (La{sub 0.6}Sm{sub 0.4})B{sub 6} prepared for identical synthesis conditions, (La{sub 0.6}Ba{sub 0.4})B{sub 6} is shown to have the most excellent thermionic emission

  19. Reconstruction of electrical capacitance tomography images based on fast linearized alternating direction method of multipliers for two-phase flow system

    Institute of Scientific and Technical Information of China (English)

    Chongkun Xia; Chengli Su⁎; Jiangtao Cao; Ping Li

    2016-01-01

    Electrical capacitance tomography (ECT) has been applied to two-phase flow measurement in recent years. Image reconstruction algorithms play an important role in the successful applications of ECT. To solve the il-posed and nonlinear inverse problem of ECT image reconstruction, a new ECT image reconstruction method based on fast lin-earized alternating direction method of multipliers (FLADMM) is proposed in this paper. On the basis of theoretical analysis of compressed sensing (CS), the data acquisition of ECT is regarded as a linear measurement process of permittivity distribution signal of pipe section. A new measurement matrix is designed and L1 regularization method is used to convert ECT inverse problem to a convex relaxation problem which contains prior knowledge. A new fast alternating direction method of multipliers which contained linearized idea is employed to minimize the objective function. Simulation data and experimental results indicate that compared with other methods, the quality and speed of reconstructed images are markedly improved. Also, the dynamic experimental results in-dicate that the proposed algorithm can fulfil the real-time requirement of ECT systems in the application.

  20. Application of an aqueous two-phase micellar system to extract bromelain from pineapple (Ananas comosus) peel waste and analysis of bromelain stability in cosmetic formulations.

    Science.gov (United States)

    Spir, Lívia Genovez; Ataide, Janaína Artem; De Lencastre Novaes, Letícia Celia; Moriel, Patrícia; Mazzola, Priscila Gava; De Borba Gurpilhares, Daniela; Silveira, Edgar; Pessoa, Adalberto; Tambourgi, Elias Basile

    2015-01-01

    Bromelain is a set of proteolytic enzymes found in pineapple (Ananas comosus) tissues such as stem, fruit and leaves. Because of its proteolytic activity, bromelain has potential applications in the cosmetic, pharmaceutical, and food industries. The present study focused on the recovery of bromelain from pineapple peel by liquid-liquid extraction in aqueous two-phase micellar systems (ATPMS), using Triton X-114 (TX-114) and McIlvaine buffer, in the absence and presence of electrolytes CaCl2 and KI; the cloud points of the generated extraction systems were studied by plotting binodal curves. Based on the cloud points, three temperatures were selected for extraction: 30, 33, and 36°C for systems in the absence of salts; 40, 43, and 46°C in the presence of KI; 24, 27, and 30°C in the presence of CaCl2 . Total protein and enzymatic activities were analyzed to monitor bromelain. Employing the ATPMS chosen for extraction (0.5 M KI with 3% TX-114, at pH 6.0, at 40°C), the bromelain extract stability was assessed after incorporation into three cosmetic bases: an anhydrous gel, a cream, and a cream-gel formulation. The cream-gel formulation presented as the most appropriate base to convey bromelain, and its optimal storage conditions were found to be 4.0 ± 0.5°C. The selected ATPMS enabled the extraction of a biomolecule with high added value from waste lined-up in a cosmetic formulation, allowing for exploration of further cosmetic potential.

  1. Coupling two-phase fluid flow with two-phase darcy flow in anisotropic porous media

    KAUST Repository

    Chen, J.

    2014-06-03

    This paper reports a numerical study of coupling two-phase fluid flow in a free fluid region with two-phase Darcy flow in a homogeneous and anisotropic porous medium region. The model consists of coupled Cahn-Hilliard and Navier-Stokes equations in the free fluid region and the two-phase Darcy law in the anisotropic porous medium region. A Robin-Robin domain decomposition method is used for the coupled Navier-Stokes and Darcy system with the generalized Beavers-Joseph-Saffman condition on the interface between the free flow and the porous media regions. Obtained results have shown the anisotropic properties effect on the velocity and pressure of the two-phase flow. 2014 Jie Chen et al.

  2. Magnetic ionic liquid aqueous two-phase system coupled with high performance liquid chromatography: A rapid approach for determination of chloramphenicol in water environment.

    Science.gov (United States)

    Yao, Tian; Yao, Shun

    2017-01-20

    A novel organic magnetic ionic liquid based on guanidinium cation was synthesized and characterized. A new method of magnetic ionic liquid aqueous two-phase system (MILATPs) coupled with high-performance liquid chromatography (HPLC) was established to preconcentrate and determine trace amount of chloramphenicol (CAP) in water environment for the first time. In the absence of volatile organic solvents, MILATPs not only has the excellent properties of rapid extraction, but also exhibits a response to an external magnetic field which can be applied to assist phase separation. The phase behavior of MILATPs was investigated and phase equilibrium data were correlated by Merchuk equation. Various influencing factors on CAP recovery were systematically investigated and optimized. Under the optimal conditions, the preconcentration factor was 147.2 with the precision values (RSD%) of 2.42% and 4.45% for intra-day (n=6) and inter-day (n=6), respectively. The limit of detection (LOD) and limit of quantitation (LOQ) were 0.14ngmL(-1) and 0.42ngmL(-1), respectively. Fine linear range of 12.25ngmL(-1)-2200ngmL(-1) was obtained. Finally, the validated method was successfully applied for the analysis of CAP in some environmental waters with the recoveries for the spiked samples in the acceptable range of 94.6%-99.72%. Hopefully, MILATPs is showing great potential to promote new development in the field of extraction, separation and pretreatment of various biochemical samples. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. Extraction and separation of tungsten (VI) from aqueous media with Triton X-100-ammonium sulfate-water aqueous two-phase system without any extractant.

    Science.gov (United States)

    Yongqiang Zhang; Tichang Sun; Tieqiang Lu; Chunhuan Yan

    2016-11-25

    An aqueous two-phase system composed of Triton X-100-(NH4)2SO4-H2O was proposed for extraction and separation of tungsten(VI) from aqueous solution without using any extractant. The effects of aqueous pH, concentration of ammonium sulfate, Triton X-100 and tungsten, extracting temperature on the extraction of tungsten were investigated. The extraction of tungsten has remarkable relationship with aqueous pH and are to above 90% at pH=1.0-3.0 under studied pH range (pH=1.0-7.0) and increases gradually with increasing Triton X-100 concentration, but decreases slightly with increasing ammonium sulfate concentration. The extraction percentage of tungsten is hardly relevant to temperature but its distribution coefficient linearly increases with increasing temperature within 303.15-343.15K. The distribution coefficient of tungsten increases with the increase of initial tungsten concentration (0.1-3%) and temperature (303.15 K-333.15K). The solubilization capacity of tungsten in Triton X-100 micellar phase is independent of temperature. FT-IR analysis reveals that there is no evident interaction between polytungstate anion and ether oxygen unit in Triton X-100, and DLS analysis indicates that zeta potential of Triton X-100 micellar phase have a little change from positive to negative after extracting tungsten. Based on the above-mentioned results, it can be deduced that polytungstate anions are solubilized in hydrophilic outer shell of Triton X-100 micelles by electrostatic attraction depending on its relatively high hydrophobic nature. The stripping of tungsten is mainly influenced by temperature and can be easily achieved to 95% in single stage stripping. The tungsten (VI) is separated out from solution containing Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Al(III), Cr(III) and Mn(II) under the suitable conditions.

  4. Contrasted Fitness Costs of Docking and Antibacterial Constructs in the EE and EVida3 Strains Validates Two-Phase Anopheles gambiae Genetic Transformation System.

    Directory of Open Access Journals (Sweden)

    Doug Paton

    Full Text Available The deployment of transgenic mosquitoes carrying genes for refractoriness to malaria has long been seen as a futuristic scenario riddled with technical difficulties. The integration of anti-malarial effector genes and a gene-drive system into the mosquito genome without affecting mosquito fitness is recognized as critical to the success of this malaria control strategy. Here we conducted detailed fitness studies of two Anopheles gambiae s.s. transgenic lines recently developed using a two-phase targeted genetic transformation system. In replicated cage-invasion experiments, males and females of the EE Phase-1 docking strain and EVida3 Phase-2 strain loaded with an antimicrobial peptide (AMP expressed upon blood-feeding, were mixed with individuals of a recently-colonized strain of the Mopti chromosomal form. The experimental design enabled us to detect initial strain reproductive success differences, assortative mating and hybrid vigor that may characterize mosquito release situations. In addition, the potential fitness costs of the unloaded Phase-1 and loaded Phase-2 genetic constructs, independent of the strains' original genetic backgrounds, were estimated between the 1(st instar larvae, pupae and adult stages over 10 generations. The Phase-1 unloaded docking cassette was found to have significantly lower allelic fitness relative to the wild type allele during larval development. However, overall genotypic fitness was comparable to the wild type allele across all stages leading to stable equilibrium in all replicates. In contrast, the Phase-2 construct expressing EVida3 disappeared from all replicates within 10 generations due to lower fitness of hemi- and homozygous larvae, suggesting costly background AMP expression and/or of the DsRed2 marker. This is the first study to effectively partition independent fitness stage-specific determinants in unloaded and loaded transgenic strains of a Phase-1-2 transformation system. Critically, the high

  5. Contrasted Fitness Costs of Docking and Antibacterial Constructs in the EE and EVida3 Strains Validates Two-Phase Anopheles gambiae Genetic Transformation System.

    Science.gov (United States)

    Paton, Doug; Underhill, Anne; Meredith, Janet; Eggleston, Paul; Tripet, Frederic

    2013-01-01

    The deployment of transgenic mosquitoes carrying genes for refractoriness to malaria has long been seen as a futuristic scenario riddled with technical difficulties. The integration of anti-malarial effector genes and a gene-drive system into the mosquito genome without affecting mosquito fitness is recognized as critical to the success of this malaria control strategy. Here we conducted detailed fitness studies of two Anopheles gambiae s.s. transgenic lines recently developed using a two-phase targeted genetic transformation system. In replicated cage-invasion experiments, males and females of the EE Phase-1 docking strain and EVida3 Phase-2 strain loaded with an antimicrobial peptide (AMP) expressed upon blood-feeding, were mixed with individuals of a recently-colonized strain of the Mopti chromosomal form. The experimental design enabled us to detect initial strain reproductive success differences, assortative mating and hybrid vigor that may characterize mosquito release situations. In addition, the potential fitness costs of the unloaded Phase-1 and loaded Phase-2 genetic constructs, independent of the strains' original genetic backgrounds, were estimated between the 1(st) instar larvae, pupae and adult stages over 10 generations. The Phase-1 unloaded docking cassette was found to have significantly lower allelic fitness relative to the wild type allele during larval development. However, overall genotypic fitness was comparable to the wild type allele across all stages leading to stable equilibrium in all replicates. In contrast, the Phase-2 construct expressing EVida3 disappeared from all replicates within 10 generations due to lower fitness of hemi- and homozygous larvae, suggesting costly background AMP expression and/or of the DsRed2 marker. This is the first study to effectively partition independent fitness stage-specific determinants in unloaded and loaded transgenic strains of a Phase-1-2 transformation system. Critically, the high fitness of the

  6. Extracellular ATP in the lymphohematopoietic system: P2Z purinoceptors and membrane permeabilization

    Directory of Open Access Journals (Sweden)

    Persechini P.M.

    1998-01-01

    Full Text Available The effects of extracellular nucleosides and nucleotides on many organs and systems have been recognized for almost 50 years. The effects of extracellular ATP (ATPo, UTPo, ADPo, and other agonists are mediated by P2 purinoceptors. One of the most dramatic effects of ATPo is the permeabilization of plasma membranes to low molecular mass solutes of up to 900 Da. This effect is evident in several cells of the lymphohematopoietic system and is supposed to be mediated by P2Z, an ATP4--activated purinoceptor. Here, we review some basic information concerning P2 purinoceptors and focus our attention on P2Z-associated phenomena displayed by macrophages. Using fluorescent dye uptake, measurement of free intracellular Ca2+ concentration and electrophysiological recordings, we elucidate some of the events that follow the application of ATP to the extracellular surface of macrophages. We propose a regulatory mechanism for the P2Z-associated permeabilization pore. The presence of P2 purinoceptors in cells of the lymphohematopoietic system makes them potential candidates to mediate immunoregulatory events

  7. Regulation of Pannexin 1 Surface Expression by Extracellular ATP: Potential Implications for Nervous System Function in Health and Disease

    Directory of Open Access Journals (Sweden)

    Leigh A. Swayne

    2017-08-01

    Full Text Available Pannexin 1 (Panx1 channels are widely recognized for their role in ATP release, and as follows, their function is closely tied to that of ATP-activated P2X7 purinergic receptors (P2X7Rs. Our recent work has shown that extracellular ATP induces clustering of Panx1 with P2X7Rs and their subsequent internalization through a non-canonical cholesterol-dependent mechanism. In other words, we have demonstrated that extracellular ATP levels can regulate the cell surface expression of Panx1. Here we discuss two situations in which we hypothesize that ATP modulation of Panx1 surface expression could be relevant for central nervous system function. The first scenario involves the development of new neurons in the ventricular zone. We propose that ATP-induced Panx1 endocytosis could play an important role in regulating the balance of cell proliferation, survival, and differentiation within this neurogenic niche in the healthy brain. The second scenario relates to the spinal cord, in which we posit that an impairment of ATP-induced Panx1 endocytosis could contribute to pathological neuroplasticity. Together, the discussion of these hypotheses serves to highlight important outstanding questions regarding the interplay between extracellular ATP, Panx1, and P2X7Rs in the nervous system in health and disease.

  8. Tunable aqueous polymer-phase impregnated resins-technology-a novel approach to aqueous two-phase extraction.

    Science.gov (United States)

    van Winssen, F A; Merz, J; Schembecker, G

    2014-02-14

    Aqueous Two-Phase Extraction (ATPE) represents a promising unit operation for downstream processing of biotechnological products. The technique provides several advantages such as a biocompatible environment for the extraction of sensitive and biologically active compounds. However, the tendency of some aqueous two-phase systems to form intensive and stable emulsions can lead to long phase separation times causing an increased footprint for the required mixer-settler devices or the need for additional equipment such as centrifuges. In this work, a novel approach to improve ATPE for downstream processing applications called 'Tunable Aqueous Polymer-Phase Impregnated Resins' (TAPPIR(®))-Technology is presented. The technology is based on the immobilization of one aqueous phase inside the pores of a solid support. The second aqueous phase forms the bulk liquid around the impregnated solids. Due to the immobilization of one phase, phase emulsification and phase separation of ATPE are realized in a single step. In this study, a biodegradable and sustainable aqueous two-phase system consisting of aqueous polyethylene glycol/sodiumcitrate solutions was chosen. The impregnation of different macroporous glass and ceramic solids was investigated and could be proven to be stable. Additionally, the separation of the dye Patent blue V was successfully performed with the TAPPIR(®)-Technology. Thus, the "proof of principle" of this technology is presented.

  9. McClellan Air Force Base operable unit B, two-phase extraction system demonstration test, work implementation plan for McClellan AFB, California. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1994-08-03

    This document is an integrated demonstration and work plan that presents the technical approach for design, implementation, and testing of two-phase extraction as compared with pump and treat technology in Operable Unit B, investigative cluster IC1 at the McClellan Air Force Base. This work is being coordinated with Clean Sites under a cooperative agreement with EPA's Technology Innovation Office and Superfund Innovative Technology Evaluation Program.

  10. Two-phase viscoelastic jetting

    Energy Technology Data Exchange (ETDEWEB)

    Yu, J-D; Sakai, S.; Sethian, J.A.

    2008-12-10

    A coupled finite difference algorithm on rectangular grids is developed for viscoelastic ink ejection simulations. The ink is modeled by the Oldroyd-B viscoelastic fluid model. The coupled algorithm seamlessly incorporates several things: (1) a coupled level set-projection method for incompressible immiscible two-phase fluid flows; (2) a higher-order Godunov type algorithm for the convection terms in the momentum and level set equations; (3) a simple first-order upwind algorithm for the convection term in the viscoelastic stress equations; (4) central difference approximations for viscosity, surface tension, and upper-convected derivative terms; and (5) an equivalent circuit model to calculate the inflow pressure (or flow rate) from dynamic voltage.

  11. ATP signals

    DEFF Research Database (Denmark)

    Novak, Ivana

    2016-01-01

    The Department of Biology at the University of Copenhagen explains the function of ATP signalling in the pancreas......The Department of Biology at the University of Copenhagen explains the function of ATP signalling in the pancreas...

  12. Purification of Active Myrosinase from Plants by Aqueous Two-Phase Counter-Current Chromatography

    Science.gov (United States)

    Wade, Kristina L.; Ito, Yoichiro; Ramarathnam, Aarthi; Holtzclaw, W. David; Fahey, Jed W.

    2014-01-01

    Introduction Myrosinase (thioglucoside glucohydrolase; E.C. 3.2.1.147), is a plant enzyme of increasing interest and importance to the biomedical community. Myrosinase catalyses the formation of isothiocyanates such as sulforaphane (frombroccoli) and 4-(α-l-rhamnopyranosyloxy)benzyl isothiocyanate (from moringa), which are potent inducers of the cytoprotective phase-2 response in humans, by hydrolysis of their abundant glucosinolate (β-thioglucoside N-hydroxysulphate) precursors. Objective To develop an aqueous two-phase counter-current chromatography (CCC) system for the rapid, three-step purification of catalytically active myrosinase. Methods A high-concentration potassium phosphate and polyethylene glycol biphasic aqueous two-phase system (ATPS) is used with a newly developed CCC configuration that utilises spiral-wound, flat-twisted tubing (with an ovoid cross-section). Results Making the initial crude plant extract directly in the ATPS and injecting only the lower phase permitted highly selective partitioning of the myrosinase complex before a short chromatography on a spiral disk CCC. Optimum phase retention and separation of myrosinase from other plant proteins afforded a 60-fold purification. Conclusion Catalytically active myrosinase is purified from 3-day broccoli sprouts, 7-day daikon sprouts, mustard seeds and the leaves of field-grown moringa trees, in a CCC system that is predictably scalable. PMID:25130502

  13. Pectinases partitioning in aqueous two-phase systems: an integration of the systems poly(ethylene glycol/crude dextran and poly(ethylene glycol/ammonium sulphate

    Directory of Open Access Journals (Sweden)

    STANA N. PEJIN

    2004-04-01

    Full Text Available The partitioning of pectinases in the poly(ethylene glucol4000/ammonium sulpohate system was studied and also its application for enzymes extraction from the top phase of the poly(ethylene glucol4000/crude dextran system. Almost complete one-sided partition of endo-pectinase and exo-pectinase to the bottom phase of the polymer/salt system was achieved at a tie-line length of 37.16 %. The concentration factors were 1.73 and 3.25, respectively. The highest total endo- and exo-pectinase yields (72.41 % and 69.46 %, respectively were obtained by integration of the polymer/polymer system at a tie-line of 8.61 % and a high phase volume ratio and the polymer/salt system at a tie-line of 30.23 % and a low phase volume ratio. Integration of the partitioning at a high tie-line length in the polymer/polimer and a low tie-line length in the polymer/salt system resulted in a total concentration factor of 1.5 and a purification of 1.66 fold for exo-pectinase. The addition of phosphate to this integrated system improved the total concentration factor and purification fold of the activity to 1.73 and 2.14, respectively.

  14. 基于 ATP 发光的细菌污染物检测系统%A DESIGN OF BACTERIA DETECTION SYSTEM BASED ON ATP BIOLUMINESCENCE TECHNOLOGY

    Institute of Scientific and Technical Information of China (English)

    张志杰; 王春兴

    2016-01-01

    作者设计了一种基于三磷酸腺苷(ATP)发光技术的细菌数量快速检测系统。系统运用了自动加样技术在暗室中反应,减少了外界杂光的干扰;并优化以光度校准单元,提高了检测可靠性。采用高测量灵敏度的 H5773-02型光电倍增管(PMT)进行光电转换来检测微弱的荧光信号。测试结果表明荧光强度与 ATP 浓度成线性关系。该系统检测时间短,精度高,在食品、药品安全检测中具有较广泛的应用。%According to the requirements of the current market for detecting the number of bacteria rapidly,a detecting system based on ATP bioluminescence technology is designed. In order to reduce the outside scattering light interference,the reagents are filled automatically into the dark container. The optical calibration unit enhances the reliability of the system. H5773 - 02 type PMT can realize photoelectric conversion. The testing results show that the bioluminescence has a great linear correlation with the ATP concentration. The system can detect0 rapidly and accurately,and has a strong potential in the food and drug safety detection.

  15. Time-resolved fast-neutron radiography of air-water two-phase flows in a rectangular channel by an improved detection system

    CERN Document Server

    Zboray, Robert; Mor, Ilan; Bromberger, Benjamin; Tittelmeier, Kai

    2015-01-01

    In a previous work we have demonstrated the feasibility of high-frame-rate, fast-neutron radiography of generic air-water two-phase flows in a 1.5 cm thick, rectangular flow channel. The experiments have been carried out at the high-intensity, white-beam facility of the Physikalisch-Technische Bundesanstalt, Germany, using an multi-frame, time-resolved detector developed for fast neutron resonance radiography. The results were however not fully optimal and therefore we have decided to modify the detector and optimize it for the given application, which is described in the present work. Furthermore, we managed to improve the image post-processing methodology and the noise suppression. Using the tailored detector and the improved post-processing significant increase in the image quality and an order of magnitude lower exposure times, down to 3.33 ms, have been achieved with minimized motion artifacts. Similar to the previous study, different two-phase flow regimes such as bubbly slug and churn flows have been e...

  16. The influence of secondary flow in a two-phase gas-solid system in straight channels with a non-circular cross-section

    Directory of Open Access Journals (Sweden)

    Milanović Saša M.

    2016-01-01

    Full Text Available The paper considers two-phase gas-solid turbulent flow of pneumatic transport in straight horizontal channels with a non-circular cross-section. During turbulent flow, a specific flow phenomenon, known as secondary flow, occurs in these channels in the cross-sectional plane. The existence of strong temperature gradients in the cross-sectional plane of the channel or the cases of curved channels result in the appearance of the secondary flow of the first kind. However, in straight channels with a non-circular cross-section, in the developed turbulent flow mode, a secondary flow, known as Prandtl’s secondary flow of the second kind, is induced. The paper presents a numerical simulation of a developed two-phase turbulent flow by using the PHOENICS 3.3.1 software package. Reynolds stress model was used to model the turbulence. The paper provides the data on the changes in turbulent stresses in the channel cross-section as well as the velocities of solid particles transported along the channel.

  17. Review of two-phase instabilities

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Han Ok; Seo, Han Ok; Kang, Hyung Suk; Cho, Bong Hyun; Lee, Doo Jeong

    1997-06-01

    KAERI is carrying out a development of the design for a new type of integral reactors. The once-through helical steam generator is important design features. The study on designs and operating conditions which prevent flow instability should precede the introduction of one-through steam generator. Experiments are currently scheduled to understand two-phase instability, evaluate the effect of each design parameter on the critical point, and determine proper inlet throttling for the prevention of instability. This report covers general two-phase instability with review of existing studies on this topics. The general classification of two phase flow instability and the characteristics of each type of instability are first described. Special attention is paid to BWR core flow instability and once-through steam generator instability. The reactivity feedback and the effect of system parameters are treated mainly for BWR. With relation to once-through steam generators, the characteristics of convective heating and dryout point oscillation are first investigated and then the existing experimental studies are summarized. Finally chapter summarized the proposed correlations for instability boundary conditions. (author). 231 refs., 5 tabs., 47 figs

  18. Next steps in two-phase flow: executive summary

    Energy Technology Data Exchange (ETDEWEB)

    DiPippo, R.

    1980-09-01

    The executive summary includes the following topics of discussion: the state of affairs; the fundamental governing equations; the one-dimensional mixture model; the drift-flux model; the Denver Research Institute two-phase geothermal flow program; two-phase flow pattern transition criteria; a two-fluid model under development; the mixture model as applied to geothermal well flow; DRI downwell instrumentation; two-phase flow instrumentation; the Sperry Research Corporation downhole pump and gravity-head heat exchanger systems; and the Brown University two-phase flow experimental program. (MHR)

  19. Two-Phase Technology at NASA/Johnson Space Center

    Science.gov (United States)

    Ungar, Eugene K.; Nicholson, Leonard S. (Technical Monitor)

    1999-01-01

    Since the baseline International Space Station (ISS) External Active Thermal Control System (EATCS) was changed from a two-phase mechanically pumped system to a single phase cascade system in the fall of 1993, two-phase EATCS research has continued at a low level at JSC. One of-the lessons of the ISS EATCS selection was that two-phase thermal control systems must have significantly lower power than comparable single phase systems to overcome their larger radiator area, larger line and fluid mass, and perceived higher technical risk. Therefore, research at JSC has concentrated on low power mechanically pumped two-phase EATCSs. In the presentation, the results of a study investigating the trade of single and two-phase mechanically pumped EATCSs for space vehicles will be summarized. The low power two-phase mechanically pumped EATCS system under development at JSC will be described in detail and the current design status of the subscale test unit will be reviewed. Also, performance predictions for a full size EATCS will be presented. In addition to the discussion of two-phase mechanically pumped EATCS development at JSC, two-phase technologies under development for biological water processing will be discussed. These biological water processor technologies are being prepared for a 2001 flight experiment and subsequent usage on the TransHab module on the International Space Station.

  20. Experiment study of ATP system for free-space optical communications

    Institute of Scientific and Technical Information of China (English)

    XIAO Yong-jun; LIU Yan-fei; DONG Ran; XIONG Zhun

    2011-01-01

    To meet the requirement of high tracking angular accuracy for the acquisition,tracking,and pointing (ATP) subsystem of the free-space optical communication,and provide the basis for the further optical communication between maritime mobile platforms,the experimental system,which executing part for the fine tracking is voice coil motor with high frequency and good performance for error compensation,is established,and the whole system can be controlled by personal computer.A series of experiments has been done for the simulation target of different uniform speed,and the data of tracking error for fine tracking and coarse tracking are collected,analyzed and evaluateds separately,and the real-time optical power of communication laser is also collected.The result shows that standard deviation for ATP system tracking error increases with the increase of target speed,while the range of tracking error appears to be no order.Furthermore,communication link can be hold for a long time.

  1. Receptor-transporter interactions of canonical ATP-binding cassette import systems in prokaryotes.

    Science.gov (United States)

    Schneider, Erwin; Eckey, Viola; Weidlich, Daniela; Wiesemann, Nicole; Vahedi-Faridi, Ardeshir; Thaben, Paul; Saenger, Wolfram

    2012-04-01

    ATP-binding cassette (ABC) transport systems mediate the translocation of solutes across biological membranes at the expense of ATP. They share a common modular architecture comprising two pore-forming transmembrane domains and two nucleotide binding domains. In prokaryotes, ABC transporters are involved in the uptake of a large variety of chemicals, including nutrients, osmoprotectants and signal molecules. In pathogenic bacteria, some ABC importers are virulence factors. Canonical ABC import systems require an additional component, a substrate-specific receptor or binding protein for function. Interaction of the liganded receptor with extracytoplasmic loop regions of the transmembrane domains initiate the transport cycle. In this review we summarize the current knowledge on receptor-transporter interplay provided by crystal structures as well as by biochemical and biophysical means. In particular, we focus on the maltose/maltodextrin transporter of enterobacteria and the transporters for positively charged amino acids from the thermophile Geobacillus stearothermophilus and Salmonella enterica serovar Typhimurium. Copyright © 2011 Elsevier GmbH. All rights reserved.

  2. Response of two-phase droplets to intense electromagnetic radiation

    Science.gov (United States)

    Spann, James F.; Maloney, Daniel J.; Lawson, William F.; Casleton, Kent H.

    1993-04-01

    The behavior of two-phase droplets subjected to high intensity radiation pulses is studied. Droplets are highly absorbing solids in weakly absorbing liquid medium. The objective of the study was to define heating thresholds required for causing explosive boiling and secondary atomization of the fuel droplet. The results point to mechanisms for energy storage and transport in two-phase systems.

  3. Dual Monitoring of Secretion and ATP Levels during Chondrogenesis Using Perfusion Culture-Combined Bioluminescence Monitoring System

    Directory of Open Access Journals (Sweden)

    Hyuck Joon Kwon

    2015-01-01

    Full Text Available Skeletal pattern formation in limb development depends on prechondrogenic condensation which prefigures the cartilage template. However, although morphogens such as TGF-βs and BMPs have been known to play essential roles in skeletal patterning, how the morphogens induce prechondrogenic cells to aggregate and determine patterns of cartilage elements has remained unclear. Our previous study reported that ATP oscillations are induced during chondrogenesis. This result suggests the possibility that ATP oscillations lead to the oscillatory secretion of morphogens, due to the fact that secretion process requires ATP. To examine the correlation between ATP oscillations and secretion levels of morphogens, we have developed perfusion culture-combined bioluminescence monitoring system to simultaneously monitor intracellular ATP levels and secretion levels. Using this system, we found that secretory activity oscillates in phase with ATP oscillations and that secretion levels of TGF-β1 and BMP2 oscillate during chondrogenesis. The oscillatory secretion of the morphogens would contribute to amplifying the fluctuation of the morphogens, underlie the spatial patterning of morphogens, and consequently lead to skeletal pattern formation.

  4. Dual Monitoring of Secretion and ATP Levels during Chondrogenesis Using Perfusion Culture-Combined Bioluminescence Monitoring System.

    Science.gov (United States)

    Kwon, Hyuck Joon; Han, Youngbae

    2015-01-01

    Skeletal pattern formation in limb development depends on prechondrogenic condensation which prefigures the cartilage template. However, although morphogens such as TGF-βs and BMPs have been known to play essential roles in skeletal patterning, how the morphogens induce prechondrogenic cells to aggregate and determine patterns of cartilage elements has remained unclear. Our previous study reported that ATP oscillations are induced during chondrogenesis. This result suggests the possibility that ATP oscillations lead to the oscillatory secretion of morphogens, due to the fact that secretion process requires ATP. To examine the correlation between ATP oscillations and secretion levels of morphogens, we have developed perfusion culture-combined bioluminescence monitoring system to simultaneously monitor intracellular ATP levels and secretion levels. Using this system, we found that secretory activity oscillates in phase with ATP oscillations and that secretion levels of TGF-β1 and BMP2 oscillate during chondrogenesis. The oscillatory secretion of the morphogens would contribute to amplifying the fluctuation of the morphogens, underlie the spatial patterning of morphogens, and consequently lead to skeletal pattern formation.

  5. Luminescent Immunoprecipitation System (LIPS) for Detection of Autoantibodies Against ATP4A and ATP4B Subunits of Gastric Proton Pump H+,K+-ATPase in Atrophic Body Gastritis Patients

    Science.gov (United States)

    Lahner, Edith; Brigatti, Cristina; Marzinotto, Ilaria; Carabotti, Marilia; Scalese, Giulia; Davidson, Howard W; Wenzlau, Janet M; Bosi, Emanuele; Piemonti, Lorenzo; Annibale, Bruno; Lampasona, Vito

    2017-01-01

    Objectives: Circulating autoantibodies targeting the H+/K+-ATPase proton pump of gastric parietal cells are considered markers of autoimmune gastritis, whose diagnostic accuracy in atrophic body gastritis, the pathological lesion of autoimmune gastritis, remains unknown. This study aimed to assess autoantibodies against ATP4A and ATP4B subunits of parietal cells H+, K+-ATPase in atrophic body gastritis patients and controls. Methods: One-hundred and four cases with atrophic body gastritis and 205 controls were assessed for serological autoantibodies specific for ATP4A or ATP4B subunits using luminescent immunoprecipitation system (LIPS). Recombinant luciferase-reporter-fused-antigens were expressed by in vitro transcription-translation (ATP4A) or after transfection in Expi293F cells (ATP4B), incubated with test sera, and immune complexes recovered using protein-A-sepharose. LIPS assays were compared with a commercial enzyme immunoassay (EIA) for parietal cell autoantibodies. Results: ATP4A and ATP4B autoantibody titers were higher in cases compared to controls (Pgastritis. Both assays had the highest sensitivity, at the cost of diagnostic accuracy (89 and 90% specificity), outperforming traditional EIA. Once validated, these LIPS assays should be valuable screening tools for detecting biomarkers of damaged atrophic oxyntic mucosa. PMID:28102858

  6. TWO PHASE FLOW SPLIT MODEL FOR PARALLEL CHANNELS

    African Journals Online (AJOL)

    Ifeanyichukwu Onwuka

    The equations are solved using the Broyden'smethod ... channel system subjected to a two-phase flow transient, and the results have been very .... system pressure, the heat addition rates inside ... three dimensional flows in the LP.

  7. Using yeast two-hybrid system to detect interactions of ATP synthase subunits from Spinacia oleracea

    Institute of Scientific and Technical Information of China (English)

    石晓冰; 魏家绵; 沈允钢

    2000-01-01

    Subunit interactions among the chloroplast ATP synthase subunits were studied using the yeast two-hybrid system. Various pairwise combinations of genes encoding a, p, y, 8 and e subunits of Spinach ATP synthase fused to the binding domain or activation domain of GAL4 DNA were introduced into yeast and then expression of a reporter gene encoding p-galactosidase was detected. Of all the combinations, that of y and e subunit genes showed the highest level of reporter gene expression, while those of a and p, a and e, p and e and p and 8 induced stable and significant reporter gene expression. The combination of 8 and e as well as that of 8 and y induced weak and unstable reporter gene expression. However, combinations of a and y, p and y and a and 8 did not induce reporter gene expression. These results suggested that specific and strong interactions between y and e, a and p, a and e, p and e and p and 8 subunits, and weak and transient interactions between 8 and e and 8 and y subunits occurred in the yeast

  8. Performance and microbial community dynamics in a two-phase anaerobic co-digestion system using cassava dregs and pig manure.

    Science.gov (United States)

    Ren, Jiwei; Yuan, Xufeng; Li, Jie; Ma, Xuguang; Zhao, Ye; Zhu, Wanbing; Wang, Xiaofen; Cui, Zongjun

    2014-03-01

    The two-phase anaerobic co-digestion of cassava dregs (CD) with pig manure (PM) was evaluated using four sequencing batch reactors (SBRs) and a continuously stirred tank reactor (CSTR). The effect of seven different PM to CD volatile solid ratios (10:0, 8:2, 6:4, 5:5, 4:6, 2:8 and 0:10) on the acidification phase was investigated. Results indicated the concentrations of soluble chemical oxygen demand, NH4-N and volatile fatty acids increased substantially at seven ratios. Co-acidification of PM and CD performed well. Methanogenic fermentation of the acidification products at seven ratios was steady in CSTR. The highest methane yield and VS removal of 0.352m(3)/kg VSadded and 68.5% were achieved at PM:CD (4:6). The microbial population in CSTR was analyzed using molecular methods. Findings revealed that bacteria such as Firmicutes and Bacteroidetes, archaea such as Methanobacteriales and Methanomicrobiales were advantageous populations. Co-digestion of PM and CD supported higher quantity and diversity of methanogens.

  9. CFD Analysis and Visualization of the Two Phase Flow in a Thermosyphon for a Passive Heat Removal System of a Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Joseph; Lee, Jae Young [Handong Global University, Pohang (Korea, Republic of)

    2016-05-15

    A thermosyphon, wickless heat pipe, is a heat transfer device of high thermal conductance that functions passively on the principle of evaporation and condensation of a working fluid. The heat-pipe concept was first proposed by Gaugler in 1942. After its independent invention by Grover in the early 1960s, serious development progress was made, and the heat pipe concept was studied intensively for both space and terrestrial applications, because of its beneficial characteristics. Annamalai and Ramalingam developed a CFD modeling for wick part of heat pipe using commercial code, ANSYS CFX. Khurram Kafeel numerically studied thermal hydraulic characteristics of thermosyphon in both transient and steady state. Bandar Fadhl et al. built a CFD modeling for boiling and condensing of thermosyphon using VOF method of ANSYS Fluent. They made user defined function (UDF) to define source term based on Lee model. In this study, CFD model of 1m-thermosyphon has been studied using VOF model. Unlike formal studies, vacuum pressure condition was applied because thermosyphon with vacuum inner pressure is much generally used. Furthermore, to check out hydraulic characteristics of the model, transparent thermosyphon experiment also has been conducted. The main purpose of this research is the investigation of CFD model of thermosyphon. Simulations using VOF method were performed to analyze evaporating, condensing and two phase flow of a thermosyphon. The simulation results show that complex phenomena inside of thermosyphon can be modeled using VOF method. Flow visualizations of working fluid matched well with transparent heat pipe experiment.

  10. The downstream atpE cistron is efficiently translated via its own cis-element in partially overlapping atpB–atpE dicistronic mRNAs in chloroplasts

    OpenAIRE

    Suzuki, Haruka; Kuroda, Hiroshi; Yukawa, Yasushi; Sugiura, Masahiro

    2011-01-01

    The chloroplast atpB and atpE genes encode subunits β and ε of the ATP synthase, respectively. They are co-transcribed as dicistronic mRNAs in flowering plants. An unusual feature is an overlap (AUGA) of the atpB stop codon (UGA) with the atpE start codon (AUG). Hence, atpE translation has been believed to depend on atpB translation (i.e. translational coupling). Using an in vitro translation system from tobacco chloroplasts, we showed that both atpB and atpE cistrons are translated from the ...

  11. Two phase decision algorithm of replica allocation

    Institute of Scientific and Technical Information of China (English)

    Zuo Chaoshu; Liu Xinsong; Wang Zheng; Li Yi

    2006-01-01

    In distributed parallel server system, location and redundancy of replicas have great influence on availability and efficiency of the system. In order to improve availahility and efficiency of the system, two phase decision algorithm of replica allocation is proposed. The algorithm which makes use of auto-regression model dynamically predicts the future count of READ and WRITE operation, and then determines location and redundancy of replicas by considering availability, CPU and bands of the network. The algorithm can not only ensure the requirement of availability, but also reduce the system resources consumed by all the operations in a great scale. Analysis and test show that communication complexity and time complexity of the algorithm satisfy O( n ), resource optimizing scale increases with the increase of READ count.

  12. Thermo-Fluid Dynamics of Two-Phase Flow

    CERN Document Server

    Ishii, Mamrou

    2011-01-01

    "Thermo-fluid Dynamics of Two-Phase Flow, Second Edition" is focused on the fundamental physics of two-phase flow. The authors present the detailed theoretical foundation of multi-phase flow thermo-fluid dynamics as they apply to: Nuclear reactor transient and accident analysis; Energy systems; Power generation systems; Chemical reactors and process systems; Space propulsion; Transport processes. This edition features updates on two-phase flow formulation and constitutive equations and CFD simulation codes such as FLUENT and CFX, new coverage of the lift force model, which is of part

  13. Microgravity Two-Phase Flow Transition

    Science.gov (United States)

    Parang, M.; Chao, D.

    1999-01-01

    Two-phase flows under microgravity condition find a large number of important applications in fluid handling and storage, and spacecraft thermal management. Specifically, under microgravity condition heat transfer between heat exchanger surfaces and fluids depend critically on the distribution and interaction between different fluid phases which are often qualitatively different from the gravity-based systems. Heat transfer and flow analysis in two-phase flows under these conditions require a clear understanding of the flow pattern transition and development of appropriate dimensionless scales for its modeling and prediction. The physics of this flow is however very complex and remains poorly understood. This has led to various inadequacies in flow and heat transfer modeling and has made prediction of flow transition difficult in engineering design of efficient thermal and flow systems. In the present study the available published data for flow transition under microgravity condition are considered for mapping. The transition from slug to annular flow and from bubbly to slug flow are mapped using dimensionless variable combination developed in a previous study by the authors. The result indicate that the new maps describe the flow transitions reasonably well over the range of the data available. The transition maps are examined and the results are discussed in relation to the presumed balance of forces and flow dynamics. It is suggested that further evaluation of the proposed flow and transition mapping will require a wider range of microgravity data expected to be made available in future studies.

  14. Prolonging cell-free protein synthesis with a novel ATP regeneration system.

    Science.gov (United States)

    Kim, D M; Swartz, J R

    1999-01-01

    A new approach for the regeneration of adenosine triphosphate (ATP) during cell-free protein synthesis was developed to prolong the synthesis and also to avoid the accumulation of inorganic phosphate. This approach was demonstrated in a batch system derived from Escherichia coli. Contrary to the conventional methods in which exogenous energy sources contain high-energy phosphate bonds, the new system was designed to generate continuously the required high-energy phosphate bonds within the reaction mixture, thereby recycling the phosphate released during protein synthesis. If allowed to accumulate, phosphate inhibits protein synthesis, most likely by reducing the concentration of free magnesium ion. Pediococcus sp. pyruvate oxidase, when introduced in the reaction mixture along with thiamine pyrophosphate (TPP) and flavin adenine dinucleotide (FAD), catalyzed the generation of acetyl phosphate from pyruvate and inorganic phosphate. Acetyl kinase, already present with sufficient activity in Escherichia coli S30 extract, then catalyzed the regeneration of ATP. Oxygen is required for the generation of acetyl phosphate and the H(2)O(2) produced as a byproduct is sufficiently degraded by endogenous catalase activity. Through the continuous supply of chemical energy, and also through the prevention of inorganic phosphate accumulation, the duration of protein synthesis is extended up to 2 h. Protein accumulation levels also increase. The synthesis of human lymphotoxin receives greater benefit than than that of chloramphenicol acetyl transferase, because the former is more sensitive to phosphate inhibition. Finally, through repeated addition of pyruvate and amino acids during the reaction period, protein synthesis continued for 6 h in the new system, resulting in a final yield of 0.7 mg/mL.

  15. Design and Function of Supramolecular Recognition Systems Based on Guest-Targeting Probe-Modified Cyclodextrin Receptors for ATP.

    Science.gov (United States)

    Fujita, Kyohhei; Fujiwara, Shoji; Yamada, Tatsuru; Tsuchido, Yuji; Hashimoto, Takeshi; Hayashita, Takashi

    2017-01-20

    In this study, we have developed a rational design strategy to obtain highly selective supramolecular recognition systems of cyclodextrins (CyDs) on the basis of the lock and key principle. We designed and synthesized dipicolylamine (dpa)-modified γ-CyD-Cu(2+) complexes possessing an azobenzene unit (Cu·1-γ-CyD) and examined how they recognized phosphoric acid derivatives in water. The results revealed that Cu·1-γ-CyD recognized ATP with high selectivity over other phosphoric acid derivatives. The significant blue shift in the UV-vis spectra and (1)H NMR analysis suggested that the selective ATP recognition was based on the multipoint interactions between the adenine moiety of ATP and both the CyD cavity and the azobenzene unit in addition to the recognition of phosphoric moieties by the Cu-dpa complex site. Our unique receptor made it capable of distinguishing ATP from AMP and ADP, revealing the discrimination of even a length of one phosphoric group. This study demonstrates that, compared to conventional recognition systems of CyDs, this multipoint recognition system confers a higher degree of selectivity for certain organic molecules, such as ATP, over their similar derivatives.

  16. Recovery of endo-polygalacturonase using polyethylene glycol-salt aqueous two-phase extraction with polymer recycling

    OpenAIRE

    Wu, You-Ting; Pereira, Martinha; Venâncio, Armando; Teixeira, J. A.

    2000-01-01

    The partitioning behaviour of endo-polygalacturonase (endo-PG) and total protein from a clarified Kluyveromyces marxianus fermentation broth in polyethylene glycol (PEG)-ammonium sulfate and PEG-potassium phosphate (pH=7) aqueous two-phase systems was experimentally investigated. Both the enzyme and total protein partitioned in the bottom phase for these two kinds of systems. The enzyme partitioning coefficient can be lower than 0.01 in PEG8000-(NH4)2SO4 ATPS with a large phase volume ratio a...

  17. 75 FR 8467 - Airworthiness Directives; BAE SYSTEMS (Operations) Limited Model ATP Airplanes

    Science.gov (United States)

    2010-02-25

    ... (Operations) Limited Model ATP Airplanes AGENCY: Federal Aviation Administration (FAA), Department of... tasks were introduced by Service Bulletin (SB) ATP-51-002 * * *. As it was determined that these... environmental inspections for the fuselage. These additional tasks were introduced by Service Bulletin (SB)...

  18. Inhibition of chemokine expression in rat inflamed paws by systemic use of the antihyperalgesic oxidized ATP

    Directory of Open Access Journals (Sweden)

    Ticozzi Paolo

    2005-07-01

    Full Text Available Abstract Background We previously showed that local use of periodate oxidized ATP (oATP, a selective inhibitor of P2X7 receptors for ATP in rat paw treated with Freund's adjuvant induced a significant reduction of hyperalgesia Herein we investigate the role of oATP, in the rat paws inflamed by carrageenan, which mimics acute inflammation in humans. Results Local, oral or intravenous administration of a single dose of oATP significantly reduced thermal hyperalgesia in hind paws of rats for 24 hours, and such effect was greater than that induced by diclofenac or indomethacin. Following oATP treatment, the expression of the pro-inflammatory chemokines interferon-gamma-inducible protein-10 (IP-10, mon ocyte chemoattractant protein-1 (MCP-1 and interleukin-8 (IL-8 within the inflamed tissues markedly decreased on vessels and infiltrated cells. In parallel, the immunohistochemical findings showed an impairment, with respect to the untreated rats, in P2X7 expression, mainly on nerves and vessels close to the site of inflammation. Finally, oATP treatment significantly reduced the presence of infiltrating inflammatory macrophages in the paw tissue. Conclusion Taken together these results clearly show that oATP reduces carrageenan-induced inflammation in rats.

  19. OBSERVATIONS ON AN ATP-SENSITIVE PROTEIN SYSTEM FROM THE PLASMODIA OF A MYXOMYCETE

    Science.gov (United States)

    Ts'o, Paul O. P.; Bonner, James; Eggman, Luther; Vinograd, Jerome

    1956-01-01

    1. Extracts of the plasmodia of the myxomycete, Physarum polycephalum, exhibit reversible decreases in viscosity in response to the addition of ATP under appropriate conditions. The protoplasm material prepared by extraction with KCl solution can apparently exist in either a high or a low viscosity state. As prepared, it is in the low viscosity condition. Rapid and extensive increases in viscosity of the extract are brought about by addition of AMP, inorganic phosphate, or, under certain conditions, of ATP. Only after the high viscosity state has been attained does addition of appropriate quantities of ATP cause a reversible decrease in viscosity. 2. The active principle of crude plasmodial extracts may be concentrated by fractional precipitation with ammonium sulfate and is found in the fraction precipitated between 30 and 40 per cent saturation. This material possesses a higher viscosity than does the original crude extract and is apparently in the high viscosity state since the addition of ATP causes an immediate reversible decrease in viscosity. 3. The ATP-sensitive fraction of myxomycete plasmodia possesses a viscosity which is dependent upon its previous thermal treatment. Extracts incubated at 0° for a period of a few hours increase greatly in viscosity when they are returned to 24.5°. This increased viscosity is structural in nature, is destroyed by mechanical agitation of the solution, and may be reversibly destroyed by addition of ATP. 4. It is suggested that the ATP-responsive protein of myxomycete plasmodia may be related to sol-gel transformations which have been observed in intact plasmodia and may participate in the protoplasmic streaming of the intact organism. This suggestion is based upon the following facts: (a) the protoplasmic streaming of myxomycete plasmodia is increased by microinjection of ATP; (b) the gel portion of the cytoplasm at the site of the microinjection of ATP is extensively converted to the sol state. The changes in structure

  20. Structure, function, and evolution of bacterial ATP-binding cassette systems

    Energy Technology Data Exchange (ETDEWEB)

    Davidson, A.L.; Dassa, E.; Orelle, C.; Chen, J. (Purdue)

    2010-07-27

    The ATP-binding cassette (ABC) systems constitute one of the largest superfamilies of paralogous sequences. All ABC systems share a highly conserved ATP-hydrolyzing domain or protein (the ABC; also referred to as a nucleotide-binding domain [NBD]) that is unequivocally characterized by three short sequence motifs (Fig. 1): these are the Walker A and Walker B motifs, indicative of the presence of a nucleotide-binding site, and the signature motif, unique to ABC proteins, located upstream of the Walker B motif (426). Other motifs diagnostic of ABC proteins are also indicated in Fig. 1. The biological significance of these motifs is discussed in Structure, Function, and Dynamics of the ABC. ABC systems are widespread among living organisms and have been detected in all genera of the three kingdoms of life, with remarkable conservation in the primary sequence of the cassette and in the organization of the constitutive domains or subunits (203, 420). ABC systems couple the energy of ATP hydrolysis to an impressively large variety of essential biological phenomena, comprising not only transmembrane (TM) transport, for which they are best known, but also several non-transport-related processes, such as translation elongation (62) and DNA repair (174). Although ABC systems deserve much attention because they are involved in severe human inherited diseases (107), they were first discovered and characterized in detail in prokaryotes, as early as the 1970s (13, 148, 238, 468). The most extensively analyzed systems were the high-affinity histidine and maltose uptake systems of Salmonella enterica serovar Typhimurium and Escherichia coli. Over 2 decades ago, after the completion of the nucleotide sequences encoding these transporters in the respective laboratories of Giovanna Ames and Maurice Hofnung, Hiroshi Nikaido and colleagues noticed that the two systems displayed a global similarity in the nature of their components and, moreover, that the primary sequences of MalK and

  1. Two Phase Technology Development Initiatives

    Science.gov (United States)

    Didion, Jeffrey R.

    1999-01-01

    Three promising thermal technology development initiatives, vapor compression thermal control system, electronics cooling, and electrohydrodynamics applications are outlined herein. These technologies will provide thermal engineers with additional tools to meet the thermal challenges presented by increased power densities and reduced architectural options that will be available in future spacecraft. Goddard Space Flight Center and the University of Maryland are fabricating and testing a 'proto- flight' vapor compression based thermal control system for the Ultra Long Duration Balloon (ULDB) Program. The vapor compression system will be capable of transporting approximately 400 W of heat while providing a temperature lift of 60C. The system is constructed of 'commercial off-the-shelf' hardware that is modified to meet the unique environmental requirements of the ULDB. A demonstration flight is planned for 1999 or early 2000. Goddard Space Flight Center has embarked upon a multi-discipline effort to address a number of design issues regarding spacecraft electronics. The program addressed the high priority design issues concerning the total mass of standard spacecraft electronics enclosures and the impact of design changes on thermal performance. This presentation reviews the pertinent results of the Lightweight Electronics Enclosure Program. Electronics cooling is a growing challenge to thermal engineers due to increasing power densities and spacecraft architecture. The space-flight qualification program and preliminary results of thermal performance tests of copper-water heat pipes are presented. Electrohydrodynamics (EHD) is an emerging technology that uses the secondary forces that result from the application of an electric field to a flowing fluid to enhance heat transfer and manage fluid flow. A brief review of current EHD capabilities regarding heat transfer enhancement of commercial heat exchangers and capillary pumped loops is presented. Goddard Space Flight

  2. Extraction of endo-pectinase activity from the culture filtrate of Polyporus squamosus by aqueous two-phase systems composed of low molecular mass polyethylene glycol and phosphate salt

    Directory of Open Access Journals (Sweden)

    Peričin Draginja M.

    2004-01-01

    Full Text Available Separation of endo-pectinase activity from the culture filtrate of Polyporus squamosus - strain MMOL76, by aqueous two-phase partitioning technique in polyethylene glycol/sodium dihydrogen phosphate system was investigated as the first operation in the downstream processing of enzyme. The best results concerning the partitioning coefficient and the top phase yield were achieved in the polyethylene glycol 400/sodium dihydrogen phosphate system at the tie-line length 78.9 % at pH 3.8 (K = 8, with a 90% yield.

  3. Critical transport velocity in two-phase, horizontal pipe flow

    Energy Technology Data Exchange (ETDEWEB)

    Sommerville, D. (U.S. Army Chemical Research, Development and Engineering Center, Aberdeen Proving Grounds, MD (US))

    1991-02-01

    This paper reports on the suspension of solid particles or entrainment of liquid droplets in two- phase flow. Theoretical and empirical relationships have been derived for both instances without any consideration to the similarities between the two. However, a general relation for two-phase flow is desirable since there are systems that cannot be readily defined due to the dual (solid/liquid) nature of the transported material, such as colloids, pulp, slurries, and sludge. Using turbulence theory, one general equation can be derived to predict critical transport velocities for two-phase horizontal flow.

  4. Control System of Two-Phase Brushless DC Gyro Motor Based on DSP%基于DSP的两相无刷直流陀螺电机稳速系统

    Institute of Scientific and Technical Information of China (English)

    吴梅锡; 付鲁华; 林玉池

    2013-01-01

    The research of the influence of gyro motor speed stability on the north-finding result is studied in order to improve the gyro north-finding precision. The paper introduces a two-phase brushless DC gyro motor control system based on TMS320LF2407A. First,it expounds the two-phase brushless DC motor's working principle. Then through the design of the hardware and software system, the close-loop control of two-phase brushless DC gyro motor is realized. The experimental results show that,the system can drive the brushless DC gyro motor well starting,braking and smooth running. The precision of the steady speed is less than 10~6 and the characteristics of the system satisfy the gyroscope demand.%为了进一步提高陀螺仪的寻北精度,分析研究了陀螺电机转速大小和转速精度对寻北结果的影响.在此基础上设计了一种基于TMS320LF2407A的两相无刷直流陀螺电机控制系统,阐述了两相无刷直流电机的工作原理,给出了电机的简化结构及数学模型,并通过对硬件系统和软件算法的设计实现了两相无刷直流陀螺电机的闭环控制.实验结果表明:系统可以很好地完成电机的启动、制动和平稳运行,转速精度优于10-6,满足陀螺仪的工作要求.

  5. Star Tracker Based ATP System Conceptual Design and Pointing Accuracy Estimation

    Science.gov (United States)

    Orfiz, Gerardo G.; Lee, Shinhak

    2006-01-01

    A star tracker based beaconless (a.k.a. non-cooperative beacon) acquisition, tracking and pointing concept for precisely pointing an optical communication beam is presented as an innovative approach to extend the range of high bandwidth (> 100 Mbps) deep space optical communication links throughout the solar system and to remove the need for a ground based high power laser as a beacon source. The basic approach for executing the ATP functions involves the use of stars as the reference sources from which the attitude knowledge is obtained and combined with high bandwidth gyroscopes for propagating the pointing knowledge to the beam pointing mechanism. Details of the conceptual design are presented including selection of an orthogonal telescope configuration and the introduction of an optical metering scheme to reduce misalignment error. Also, estimates are presented that demonstrate that aiming of the communications beam to the Earth based receive terminal can be achieved with a total system pointing accuracy of better than 850 nanoradians (3 sigma) from anywhere in the solar system.

  6. Development of a rapid optic bacteria detecting system based on ATP bioluminescence

    Science.gov (United States)

    Liu, Jun Tao; Luo, JinPing; Liu, XiaoHong; Cai, XinXia

    2014-12-01

    A rapid optic bacteria detecting system based on the principle of Adenosine triphosphate(ATP) bioluminescence was presented in this paper. This system consisted of bioluminescence-based biosensor and the high-sensitivity optic meter. A photon counting photomultiplier tube (PMT) module was used to improve the detection sensitivity, and a NIOS II/f processor based on a Field Programmable Gate Array(FPGA) was used to control the system. In this work, Micrococcus luteus were chosen as the test sample. Several Micrococcus luteus suspension with different concentration was tested by both T2011 and plate counting method. By comparing the two group results, an calibration curve was obtained from the bioluminescence intensity for Micrococcus luteus in the range of 2.3×102 ~ 2.3×106 CFU/mL with a good correlation coefficient of 0.960. An impacting Air microorganism sampler was used to capture Airborne Bacteria, and 8 samples were collected in different place. The TBC results of 8 samples by T2011 were between 10 ~ 2×103 cfu/mL, consistent with that of plate counting method, which indicated that 8 samples were between 10 ~ 3×103 cfu/mL. For total airborne bacteria count was small, correlation coefficient was poor. Also no significant difference was found between T2011 and plate counting method by statistical analyses.

  7. 基于AT89C52单片机的步进电机控制系统研究%Research of Control System of Two-phase Hybrid Stepping Motor Based on AT89C52 Microcontrollers

    Institute of Scientific and Technical Information of China (English)

    何冲; 王淑红; 侯胜伟; 牛慧文

    2012-01-01

    The design scheme Based on AT89C52 Microcontrollers of two phase hybrid stepping motor control system is introduced, reflects two phase hybrid stepping motor control method in principle, increase the flexibility of stepping motor control system design. The control system adopts AT89C52 as controller, use BUW49 power tube of double H bridge type circuit as driver, join button control and LCD1602 display. The circuit structure of control system is simple and the thinking design is clearly. Experimental results shows that the control system operation is simple and reliable, it has strong practicability.%本文介绍了基于AT89C52单片机的两相混合式步进电机控制系统的设计方案,增加了步进电机控制系统设计的灵活性。控制系统采用AT89C52单片机作为控制器,由达林顿功率管BUW49组成的双H桥式电路作为驱动器,加入按键控制及LCD1602显示。控制系统的电路结构简单、设计思路清晰。实验表明,控制系统操作简单、运行可靠,具有较强的实用性。

  8. Sulphonamide porphyrins in the biomimetic oxidation by H{sub 2}O{sub 2}. An efficient two-phase system

    Energy Technology Data Exchange (ETDEWEB)

    Rocha Gonsalves, A.M. d`A.; Pereira, M.M.; Serra, A.C. [Departamento de Quimica: Universidade de Coimbra. Coimbra (Portugal)

    1996-12-31

    A catalytic biphasic aqueous/organic system for hydrogen peroxide oxidations was studied and improved, and a new metalloporphyrins derived from meso-tetrakis-2,6-dichlorophenylprophyr in bearing five sulphonamide side chains in the meso-phenyl and in one of the Beta-positions was synthesised and established as an highly efficient and stable catalyst working in the newly developed system. An interface mechanism is proposed to interpret the role of lipophilic acids as co-catalysts, the efficiency of the catalysis and the stability of the catalyst in the new system. (Author) 16 refs.

  9. EFFECT OF ALCOHOL ON AQUEOUS TWO-PHASE SYSTEM PROPERTIES OF SDS/CTAB/H2O/Na2SO4 SYSTEM%醇对正负离子表面活性剂双水相性质的影响

    Institute of Scientific and Technical Information of China (English)

    滕弘霓; 王利

    2004-01-01

    The effect of alcohol on the aqueous two-phase system properties of SDS/CTAB/H2O/Na2SO4 system was studied by the pseudo ternary phase diagram. The electrostatic forces (both attraction and repulsion) between cationic surfactant and anionic surfactant decreased because of the interaction of alcohol hydroxyl group and surfactant polar group. As a result, the phase area width of aqueous two-phase system increased. Long chain alcohol (more than five carbonatoms), which was in high concentration in the SDS/CTAB/H2O/Na2SO4) system, caused the anionic aqueous two-phase system area to vanish and the cationic aqueous two-phase system area to become wider. The CTAB rich phase turned from top phase to bottom phase.

  10. Extraction of doxycycline hydrochloride using anhydrous alcohol and acetone binary aqueous two phase system%醇和小分子有机物二元双水相体系萃取盐酸多西环素

    Institute of Scientific and Technical Information of China (English)

    关卫省; 邓江华; 韩娟

    2012-01-01

    基于小分子醇双水相体系和小分子有机物双水相体系,建立了乙醇与丙酮和( NH4) 2SO4形成的二元双水相体系萃取盐酸多西环素的新方法.研究了(NH4)2SO4浓度、pH值、温度、乙醇与丙酮用量和盐酸多西环素浓度对盐酸多西环素分配行为的影响.结果表明,体系的(NH4)2SO4浓度为41%,pH值在4.5 ~5.0,温度25℃,且盐酸多西环素的质量浓度70 mg/L时,萃取率可达93.61%,分配系数可达83.081.%Based on the molecular alcohol aqueous two-phase system and the small molecular organic two-phase system,the new method of using anhydrous alcohol and small molecular organic (acetone) with ( NH4)2SO4 binary aqueous two phase system for extracting doxycycline hydrochloride was set up. The influence factors on partition behaviors of doxycycline hydrochloride were studied, including the concentration of (NH4)2SO4,anhydrous alcohol and acetone consumption,pH value,temperature and doxycycline hydrochloride. The results showed that when (NH4)2SO4 concentration of 41% ,pH value of 4.5~5.0, and the temperature of 25℃ ,mass concentration of doxycycline hydrochloride 70 mg/L,the extraction rate up to 93.61% and 83.081 .respectively.

  11. Two-phase cooling fluids; Les fluides frigoporteurs diphasiques

    Energy Technology Data Exchange (ETDEWEB)

    Lallemand, A. [Institut National des Sciences Appliquees (INSA), 69 - Lyon (France)

    1997-12-31

    In the framework of the diminution of heat transfer fluid consumption, the concept of indirect refrigerating circuits, using cooling intermediate fluids, is reviewed and the fluids that are currently used in these systems are described. Two-phase cooling fluids advantages over single-phase fluids are presented with their thermophysical characteristics: solid fraction, two-phase mixture enthalpy, thermal and rheological properties, determination of heat and mass transfer characteristics, and cold storage through ice slurry

  12. 黄芩甙在EOPO/盐双水相系统中的分配系数测定及关联%Measurement and Correlation of Partition Coefficients of Baicalin in EOPO/Salt Aqueous Two-Phase Systems

    Institute of Scientific and Technical Information of China (English)

    李伟; 朱自强

    2002-01-01

    The partition coefficients of baicalin were measured in ethylene oxide and propylene oxide (EOPO)/salt aqueous two-phase systemsat 298.15K. It was found that most of baicalin partitioned into EOPO-rich phase. The partition coefficients of baicalin varied from 10 to 120.The effect of various factors, including tie-line length, salt composition, molecular weight of EOPO, and solution pH, on the partition behaviorwas investigated in EOPO/salt systems. Furthermore the partition coefficients of baicalin were correlated using the modified Diamond-Hsumodel. Good agreement with experimental data is obtained. The average relative deviations are less than 5.0%.

  13. Energy coupling to periplasmic binding protein-dependent transport systems: stoichiometry of ATP hydrolysis during transport in vivo.

    OpenAIRE

    Mimmack, M L; Gallagher, M P; Pearce, S R; Hyde, S C; Booth, I R; Higgins, C F

    1989-01-01

    Periplasmic binding protein-dependent transport systems mediate the accumulation of many diverse substrates in prokaryotic cells. Similar transport systems, including the P-glycoprotein responsible for multidrug resistance in human tumors, are also found in eukaryotes. The mechanism by which energy is coupled to the accumulation of substrate by these transport systems has been controversial. In this paper we demonstrate that ATP hydrolysis occurs in vivo concomitantly with transport. These da...

  14. Separation, concentration and determination of chloramphenicol in environment and food using an ionic liquid/salt aqueous two-phase flotation system coupled with high-performance liquid chromatography.

    Science.gov (United States)

    Han, Juan; Wang, Yun; Yu, Cuilan; Li, Chunxiang; Yan, Yongsheng; Liu, Yan; Wang, Liang

    2011-01-31

    Ionic liquid-salt aqueous two-phase flotation (ILATPF) is a novel, green, non-toxic and sensitive samples pretreatment technique. ILATPF coupled with high-performance liquid chromatography (HPLC) was developed for the analysis of chloramphenicol, which combines ionic liquid aqueous two-phase system (ILATPS) based on imidazolium ionic liquid (1-butyl-3-methylimidazolium chloride, [C(4)mim]Cl) and inorganic salt (K(2)HPO(4)) with solvent sublation. In ILATPF systems, phase behaviors of the ILATPF were studied for different types of ionic liquids and salts. The sublation efficiency of chloramphenicol in [C(4)mim]Cl-K(2)HPO(4) ILATPF was influenced by the types of salts, concentration of K(2)HPO(4) in aqueous solution, solution pH, nitrogen flow rate, sublation time and the amount of [C(4)mim]Cl. Under the optimum conditions, the average sublation efficiency is up to 98.5%. The mechanism of ILATPF contains two principal processes. One is the mechanism of IL-salt ILATPS formation, the other is solvent sublation. This method was practical when applied to the analysis of chloramphenicol in lake water, feed water, milk, and honey samples with the linear range of 0.5-500 ng mL(-1). The method yielded limit of detection (LOD) of 0.1 ng mL(-1) and limit of quantification (LOQ) of 0.3 ng mL(-1). The recovery of CAP was 97.1-101.9% from aqueous samples of environmental and food samples by the proposed method. Compared with liquid-liquid extraction, solvent sublation and ionic liquid aqueous two-phase extraction, ILATPF can not only separate and concentrate chloramphenicol with high sublation efficiency, but also efficiently reduce the wastage of IL. This novel technique is much simpler and more environmentally friendly and is suggested to have important applications for the concentration and separation of other small biomolecules.

  15. Study on aqueous two-phase extraction of L-phenylalanine by polyethylene glycol/salt system%聚乙二醇/盐双水相萃取L-苯丙氨酸的研究

    Institute of Scientific and Technical Information of China (English)

    孙晨; 刘文举; 刘宁宁

    2012-01-01

    研究了聚乙二醇/盐双水相体系的成相行为及L-苯丙氨酸在双水相中的分配规律,其中包括聚乙二醇的分子量、聚乙二醇质量分数、盐的种类及加入量、L-苯丙氨酸初始浓度和pH对萃取分离的影响。当聚乙二醇1000的质量分数为27%,磷酸氢二钾的质量浓度为O.15g/mL,L-苯丙氨酸的质量浓度为10g/L,体系的pH为8.5时,L-苯丙氨酸的萃取率最高为99.5%,分配系数最大为186.5。%An aqueous two- phase system of polyethylene glycol (PEG)/salt with the behavior of forming aqueous two-phase and the distribution rules of L-phenylalanine in the aqueous two-phase system were studied.Effects of the molecular weight of polyethylene glycol ,the mass fraction of polyethylene glycol ,the types and concentrations of salts,the initial concentration of L-phenylalanine and pH value were investigated.When the mass fraction of PEG1000 was 27% ,the mass concentration of K2HPO4was 0.]5g/mL,the initial concentration of L-phenylalanine was 10g/L and pH value was about 8.5,the highest extraction yield of L-phenylalanine could reach 99.5 %, partition coefficient of L-phenylalanine could reach 186.5.

  16. Markedly improving asymmetric oxidation of 1-(4-methoxyphenyl) ethanol with Acetobacter sp. CCTCC M209061 cells by adding deep eutectic solvent in a two-phase system

    OpenAIRE

    Wei, Ping; Liang, Jing; Cheng, Jing; Zong, Min-Hua; Lou, Wen-Yong

    2016-01-01

    Background Enantiopure (S)-1-(4-methoxyphenyl) ethanol {(S)-MOPE} can be employed as an important synthon for the synthesis of cycloalkyl [b] indoles with the treatment function for general allergic response. To date, the biocatalytic resolution of racemic MOPE through asymmetric oxidation in the biphasic system has remained largely unexplored. Additionally, deep eutectic solvents (DESs), as a new class of promising green solvents, have recently gained increasing attention in biocatalysis for...

  17. Gibbs free energy of transfer of a methylene group on {UCON + (sodium or potassium) phosphate salts} aqueous two-phase systems: Hydrophobicity effects

    OpenAIRE

    Silvério, Sara C.; Rodríguez, Oscar; Teixeira, J. A.; Macedo, Eugénia

    2010-01-01

    The Gibbs free energy of transfer of a suitable hydrophobic probe can be regarded as a measure of the relative hydrophobicity of the different phases. The methylene group (CH2) can be considered hydrophobic, and thus be a suitable probe for hydrophobicity. In this work, the partition coefficients of a series of five dinitrophenylated-amino acids were experimentally determined, at 23 °C, in three different tie-lines of the biphasic systems: (UCON + K2HPO4), (UCON + potassium phosph...

  18. Use of hydrophilic ionic liquids in a two-phase system to improve Mung bean epoxide hydrolases-mediated asymmetric hydrolysis of styrene oxide.

    Science.gov (United States)

    Chen, Wen-Jing; Lou, Wen-Yong; Yu, Chun-Yang; Wu, Hong; Zong, Min-Hua; Smith, Thomas J

    2012-12-31

    A comparative study was made of Mung bean epoxide hydrolases-catalyzed asymmetric hydrolysis of styrene oxide to (R)-1-phenyl-1,2-ethanediol in an n-hexane/buffer biphasic system containing various hydrophilic ionic liquids (ILs). Compared to the n-hexane/buffer biphasic system alone, addition of a small amount of hydrophilic ILs reduced the amount of non-enzymatic hydrolysis, and improved the reaction rate by up to 22%. The ILs with cation containing an alkanol group, namely [C(2)OHMIM][BF(4)] and [C(2)OHMIM][TfO], and the choline amino acid ILs [Ch][Arg] and [Ch][Pro] were found to be the most suitable co-solvents for the reaction, owing to their good biocompatibility with the enzyme, which led to high initial rates (0.99-1.25 μmol/min) and high product e.e.s (95%). When substrate concentration was around 30 mM, where optimal performance was observed with the IL-containing systems, the product e.e. was improved from 90% without ILs to ≥95% in the presence of ILs.

  19. Synthesis of octyl-β-D-glucopyranoside catalyzed by Thai rosewood β-glucosidase-displaying Pichia pastoris in an aqueous/organic two-phase system.

    Science.gov (United States)

    Guo, DongHeng; Xu, YanShan; Kang, YaJun; Han, ShuangYan; Zheng, SuiPing

    2016-04-01

    We explored the ability of a Thai rosewood β-glucosidase-displaying P. pastoris whole-cell biocatalyst (Pp-DCBGL) system to synthesize alkyl β-D-glucosides. The primary investigation centered on the synthesis of octyl-β-D-glucopyranoside (octyl-glu, OG). OG could be synthesized through reverse hydrolysis reaction with very low efficiency. Then, OG was synthesized between BG and octanol by a transglycosylation reaction. In a 2-ml reaction system, OG was synthesized with a conversion rate of 51.1% in 3h when 5 mg/ml BG was utilized as the glucosyl donor under optimized conditions. And, even after being reused four times, the Pp-DCBGL was relatively stable. Additionally, a 500-ml-scale reaction system was conducted in a 2-L stirred reactor with a conversion rate of 47.5% in 1.5 h. Moreover, the conversion rate did not decrease after the whole-cell catalyst was reused two times. In conclusion, Pp-DCBGL has high reaction efficiency and operational stability, which is a powerful biocatalyst available for industrial synthesis. Copyright © 2015. Published by Elsevier Inc.

  20. Two-phase flow simulation inside a tubing string with artificial lift system PCP based; Simulacao do escoamento bifasico em uma coluna de producao com sistema de elevacao artificial por BCP

    Energy Technology Data Exchange (ETDEWEB)

    Vidal, F.J.T.; Salazar, A.O.; Maitelli, A.L. [Rio Grande do Norte Univ., Natal, RN (Brazil). Programa de Pos-graduacao em Engenharia Eletrica]. E-mail: francisco@dca.ufrn.br; andres@dca.ufrn.br; maitelli@dca.ufrn.br; Assmann, B.W. [PETROBRAS S.A., Natal/Fortaleza, RN/CE (Brazil). Unidade de Negocios]. E-mail: benno@petrobras.com.br; Lima, J.A. [Rio Grande do Norte Univ., Natal, RN (Brazil). Dept. de Engenharia Mecanica. Programa de Pos-graduacao em Engenharia Mecanica]. E-mail: jalima@dem.ufrn.br

    2005-07-01

    The main goal of the present work is the computational simulation of the vertical two-phase flow within a tubing string in the production of oil equipped with a PCP artificial lift system (Progressive Cavity Pumping). By initially adopting the homogeneous model for the two-phase mixture (oil and gas), the fields of velocity and pressure are evaluated for prediction of pressure loss along the tubing, as well as the spatial and temporal behavior of typical parameters as gas-oil ratio, bubble pressure, solubility ratio, void fraction, gas and oil formation volume factors, among others. Prediction of these properties is an integral part of pressure loss calculations, as well as they constitute essential parameters for optimization of any artificial lift system. The numerical simulation is based on the transport equations (continuity and momentum equations) for a pseudo-fluid through the finite difference method, and the mixture properties are evaluated by employing the black-oil fluid model. Behavior analyses of the main flow variables are made and results for a typical artificial lift system PCP based are discussed. (author)

  1. Features of the milk whey protein partitioning in polyethyleneglycol-sodium citrate aqueous two-phase systems with the goal of isolating human alpha-1 antitrypsin expressed in bovine milk.

    Science.gov (United States)

    Boaglio, Andrea; Bassani, Georgina; Picó, Guillermo; Nerli, Bibiana

    2006-06-06

    Partitioning behaviour of the bovine whey proteins (bovine serum albumin, alpha-lactoalbumin and beta-lactoglobulin) and human alpha-1 antitrypsin in aqueous two-phase systems prepared with polyethyleneglycol (molecular masses: 1000, 1450 and 3350)-sodium citrate was analysed at pH 5.2, 6.2 and 8.2. Alpha lactoalbumin concentrated in the polyethyleneglycol rich-phase, while beta-lactoglobulin, bovine serum albumin and alpha-1 antitrypsin showed affinity for the citrate rich-phase. In aqueous two-phase systems of high medium pH and high polyethyleneglycol molecular mass the protein partitioning equilibrium is displaced to the citrate rich-phase. The polyethyleneglycol 1450-pH 5.2 system with a top/bottom phase-volume ratio of 3 showed to have the best capability of recovering the alpha-1 antitrypsin from a mixture prepared with natural milk whey and human alpha-1 antitrypsin. The recovery of this protein in the bottom phase was of 90% and the purity of the obtained product was of 98%. The method appears to be suitable as a starting point to isolate other human proteins expressed in transgenic bovine milk.

  2. Two-phases-service queuing system with server breakdown and vacations%带有服务台故障和两阶段服务的休假排队系统

    Institute of Scientific and Technical Information of China (English)

    曾慧; 岳德权

    2011-01-01

    为了解决现实生产生活中的具有两阶段服务性质的休假排队问题,利用马尔可夫过程理论建立系统稳态概率方程组,并利用分块矩阵解法,得到了稳态概率的矩阵解.由此得出系统的平均队长、平均等待队长等性能指标.该成果对解决两阶段服务排队模型具有重要的理论意义和应用价值.%In order to solve the vacation queue problems with a two-phase of service in real-life production, the equations of steady-state probability were derived by applying the Markov process theory in this study. Subsequently, the matrix form solution of steady-state probability was found by using block matrix method. Furthermore, some performance measures of the system, such as the expected number of customers in the system and the expected number of customers in the queue, were also obtained. The study on the queuing systems with two-phase of service is of theoretical significance and application value.

  3. Magnetic self-assembly of microparticle clusters in an aqueous two-phase microfluidic cross-flow

    Science.gov (United States)

    Abbasi, Niki; Jones, Steven G.; Moon, Byeong-Ui; Tsai, Scott S. H.

    2015-11-01

    We present a technique that self-assembles paramagnetic microparticles on the interface of aqueous two-phase system (ATPS) fluids in a microfluidic cross-flow. A co-flow of the ATPS is formed in the microfluidic cross channel as the flows of a dilute dextran (DEX) phase, along with a flow-focused particle suspension, converges with a dilute polyethylene glycol (PEG) phase. The microparticles arrive at the liquid-liquid interface and self-assemble into particle clusters due to forces on the particles from an applied external magnetic field gradient, and the interfacial tension of the ATPS. The microparticles form clusters at the interface, and once the cluster size grows to a critical value, the cluster passes through the interface. We control the size of the self-assembled clusters, as they pass through the interface, by varying the strength of the applied magnetic field gradient and the ATPS interfacial tension. We observe rich assembly dynamics, from the formation of Pickering emulsions to clusters that are completely encapsulated inside DEX phase droplets. We anticipate that this microparticle self-assembly method may have important biotechnological applications that require the controlled assembly of cells into clusters.

  4. Efficacy and Safety of Epratuzumab in Moderately to Severely Active Systemic Lupus Erythematosus: Results From Two Phase III Randomized, Double‐Blind, Placebo‐Controlled Trials

    Science.gov (United States)

    Wallace, Daniel J.; Furie, Richard A.; Petri, Michelle A.; Pike, Marilyn C.; Leszczyński, Piotr; Neuwelt, C. Michael; Hobbs, Kathryn; Keiserman, Mauro; Duca, Liliana; Kalunian, Kenneth C.; Galateanu, Catrinel; Bongardt, Sabine; Stach, Christian; Beaudot, Carolyn; Kilgallen, Brian; Gordon, Caroline; Batalov, A.; Bojinca, M.; Djerassi, R.; Duca, L.; Horak, P.; Kolarov, Z.; Milasiene, R.; Monova, D.; Otsa, K.; Pileckyte, M.; Popova, T.; Radulescu, F.; Rashkov, R.; Rednic, S.; Repin, M.; Stoilov, R.; Tegzova, D.; Vezikova, N.; Vitek, P.; Zainea, C.; East, Far; Baek, H.; Chen, Y.; Chiu, Y.; Cho, C.; Chou, C.; Choe, J.; Huang, C.; Kang, Y.; Kang, S.; Lai, N.; Lee, S.; Park, W.; Shim, S.; Suh, C.; Yoo, W.; Armengol, H. Avila; Zapata, F. Avila; Santiago, M. Barreto; Cavalcanti, F.; Chahade, W.; Costallat, L.; Keiserman, M.; Alcala, J. Orozco; Remus, C. Ramos; Roimicher, L.; Abu‐Shakra, M.; Agarwal, V.; Agmon‐Levin, N.; Kadel, J.; Levy, Y.; Mevorach, D.; Paran, D.; Reitblat, T.; Rosner, I.; Shobha, V.; Sthoeger, Z.; Zisman, D.; Ayesu, K.; Berney, S.; Box, J.; Busch, H.; Buyon, J.; Carter, J.; Chi, J.; Clowse, M.; Collins, R.; Dao, K.; Diab, I.; Dikranian, A.; El‐Shahawy, M.; Gaylis, N.; Grossman, J.; Halpert, E.; Huff, J.; Jarjour, W.; Kao, A.; Katz, R.; Kennedy, A.; Khan, M.; Kivitz, A.; Kohen, M.; Lawrence‐Ford, T.; Lawson, J.; Levesque, M.; Lowenstein, M.; Majjhoo, A.; Mcarthur, R.; McLain, D.; Merrill, J.; Murillo, A.; Neucks, S.; Niemer, G.; Noaiseh, G.; Parker, C.; Pantojas, C.; Pattanaik, D.; Petri, M.; Pickrell, P.; Reveille, J.; Roman‐Miranda, A.; Rothfield, N.; Sankoorikal, A.; Sayers, M.; Singhal, A.; Snyder, A.; Striebich, C.; Vo, Q.; von Feldt, J.; Wallace, D.; Wasko, M.; Young, C.; Adelstein, S.; Hall, S.; Littlejohn, G.; Nicholls, D.; Suranyi, M.; Amoura, Z.; Bannert, B.; Behrens, F.; Perez, L.Carreno; Chakravarty, K.; Gonzales, F. Diaz; Davies, K.; Doria, A.; Emery, P.; Fernández‐Nebro, A.; Govoni, M.; Hachulla, E.; Hellmich, B.; Houssiau, F.; Malaise, M.; Margaux, J.; Maugars, Y.; Muñoz‐Fernández, S.; Navarro, F.; Ordi‐Ros, J.; Pellerito, R.; Pena‐Sagredo, J.; Roussou, E.; Schmidt, R. E.; Ucar‐Angulo, E.; Viallard, J‐F.; Westhovens, R.; Worm, M.; Yee, C. S.; Nayiager, S.; Reuter, H.; Spargo, C.; Bazela, B.; Brzosko, M.; Chudzik, D.; Gasztonyi, B.; Geher, P.; Ionescu, R.; Jeka, S.; Kemeny, L.; Kiss, E.; Kotyla, P.; Kovacs, L.; Kovalenko, V.; Kucharz, E.; Kwiatkowska, B.; Leszczynski, P.; Levchenko, E.; Lysenko, G.; Majdan, M.; Mihailov, C.; Nalotov, S.; Nedelciu, M.; Pavel, M.; Raskina, T.; Rebrov, B.; Rezus, E.; Semen, T.; Smakotina, S.; Stanislavchuk, M.; Stanislav, M.; Szombati, I.; Szucs, G.; Udrea, G.; Zajdel, J.; Zon‐Giebel, A.; Bonfiglioli, R.; Bustamante, R.; Klumb, E.; Ramirez, G. Medrano; Neiva, C.; Olguin, M.; Gonzaga, J.Reyes; Scotton, A.; Ayala, S. Sicsik; Ximenes, A.; Sharma, R.; Srikantiah, C.; Aelion, J.; Aranow, C.; Baker, M.; Chadha, A.; Chao, J.; Chatham, W.; Chow, A.; Clay, C.; Cohen‐Gadol, S.; Conaway, D.; Denburg, J.; Escalante, A.; Espinoza, L.; Fiechtner, J.; Fortin, I.; Fraser, A.; Furie, R.; Gladman, D.; Goddard, D.; Goldberg, M.; Gonzalez‐Rivera, R.; Gorman, J.; Griffin, R.; Haaland, D.; Halter, D.; Hemaiden, A.; Hobbs, K.; Joshi, V.; Lim, S.; Kalunian, K.; Karpouzas, G.; Khraishi, M.; Lafyatis, R.; Lee, S.; Lidman, R.; Lue, C.; Mohan, M.; Mease, P.; Mehta, C.; Mizutani, W.; Nami, A.; Nascimento, J.; Neuwelt, C.; Pappas, J.; Pope, J.; Porges, A.; Roane, G.; Rosenberg, D.; Ross, S.; Saadeh, C.; Scoville, C.; Sherrer, Y.; Solomon, M.; Surbeck, W.; Valenzuela, G.; Waller, P.; Alten, R.; Baerwald, C.; Bienvenu, B.; Bombardieri, S.; Braun, J.; Dival, L.; Espinosa, G.; Fernandez, I. Figueroa; Gomez‐Reino, J.; Gordon, C.; Hiepe, F.; Hopkinson, N.; Isenberg, D.; Jacobi, A.; Jorgensen, C.; Guern, V. Le; Paul, C.; Pego‐Reigosa, J. M.; Heredia, J. Rodriguez; Rubbert‐Roth, A.; Sabbadini, M.; Schroeder, J.; Schwarting, A.; Spieler, W.; Valesini, G.; Wollenhaupt, J.; Mendoza, A. Zea; Zouboulis, C.

    2017-01-01

    Objective Epratuzumab, a monoclonal antibody that targets CD22, modulates B cell signaling without substantial reductions in the number of B cells. The aim of this study was to report the results of 2 phase III multicenter randomized, double‐blind, placebo‐controlled trials, the EMBODY 1 and EMBODY 2 trials, assessing the efficacy and safety of epratuzumab in patients with moderately to severely active systemic lupus erythematosus (SLE). Methods Patients met ≥4 of the American College of Rheumatology revised classification criteria for SLE, were positive for antinuclear antibodies and/or anti–double‐stranded DNA antibodies, had an SLE Disease Activity Index 2000 (SLEDAI‐2K) score of ≥6 (increased disease activity), had British Isles Lupus Assessment Group 2004 index (BILAG‐2004) scores of grade A (severe disease activity) in ≥1 body system or grade B (moderate disease activity) in ≥2 body systems (in the mucocutaneous, musculoskeletal, or cardiorespiratory domains), and were receiving standard therapy, including mandatory treatment with corticosteroids (5–60 mg/day). BILAG‐2004 grade A scores in the renal and central nervous system domains were excluded. Patients were randomized 1:1:1 to receive either placebo, epratuzumab 600 mg every week, or epratuzumab 1,200 mg every other week, with infusions delivered for the first 4 weeks of each 12‐week dosing cycle, for 4 cycles. Patients across all 3 treatment groups also continued with their standard therapy. The primary end point was the response rate at week 48 according to the BILAG‐based Combined Lupus Assessment (BICLA) definition, requiring improvement in the BILAG‐2004 score, no worsening in the BILAG‐2004 score, SLEDAI‐2K score, or physician's global assessment of disease activity, and no disallowed changes in concomitant medications. Patients who discontinued the study medication were classified as nonresponders. Results In the EMBODY 1 and EMBODY 2 trials of epratuzumab, 793

  5. Partition of proteins in aqueous two-phase systems based on Cashew-nut tree gum and poly(ethylene glycol

    Directory of Open Access Journals (Sweden)

    Leonie Asfora Sarubbo

    2004-09-01

    Full Text Available The partitioning of two proteins, bovine serum albumin (BSA and trypsin was studied in an aqueous poly(ethylene glycol(PEG- Cashew-nut tree gum system. The phase diagram was provided for Cashew-nut tree gum and PEG molecular weight of 1500 at two different temperatures. The influence of several parameters including concentrations of polymers, pH, salt addition and temperature on the partitioning of these proteins were investigated.. The results of this research demonstrated the importance of the protein characteristics for partitioning in aqueous biphasic system.A partição de duas proteínas, albumina de soro bovino (BSA e tripsina foi estudada no sistema bifásico aquoso Polietileno glicol(PEG - Goma do cajueiro. O diagrama de fases foi estabelecido para a Goma do Cajueiro e para PEG de peso molecular 1500 em duas diferentes temperaturas. A influência de vários parâmetros na partição destas proteínas, incluindo concentração dos polímeros, pH, adição de sal e temperatura foi investigada. Os resultados desta pesquisa demonstraram a importância das características da proteína na partição em sistemas bifásicos aquosos.

  6. Biogasification of steam-exploded wheat straw by a two-phased digestion system%汽爆麦草的两相法生物气化

    Institute of Scientific and Technical Information of China (English)

    陈洪章; 王麾; 张爱军; 李佐虎

    2005-01-01

    蒸汽爆破作为一种新型的预处理方法被初次运用于麦草的两相气化系统,以碳酸氢铵作为补充氮源调节碳氮比,并在相同条件下以未汽爆麦草作对照试验.以汽爆麦草为原料时,水解反应器的pH值低于加入未汽爆麦草的pH值,并且在25 d后慢慢升至7;以两种麦草为原料时,甲烷反应器的pH都稳定在7左右,此时最适合甲烷生成.汽爆麦草的总固形物和挥发性固形物含量分别降低了57.5%和62.1%,下降率差不多是未汽爆麦草的2倍;纤维素和半纤维素的降解率也有了显著的提高,分别为63.0%和67.4%;木质素的降解率变化不大,都在5%左右.汽爆麦草的总产气量高于非汽爆麦草,并且一直保持较高的增长率,而非汽爆麦草的增长率一直较低;两种麦草产生的生物气中的甲烷含量大致相同,在水解反应器中后期为50%左右,在甲烷反应器中为70%左右.以上结果表明,汽爆可以促进麦草的降解,提高生物气的产量,是一种行之有效的预处理技术.%In the study, steam-explosion, a novel pretreatment method of substrate, was firstly introduced in the twophased digestion system. Ammonium bicarbonate was used as added nitrogen source to adjust C/N in the system. Under the same conditions, experiments using NPWS (non-pretreated wheat straw) were processed as the control. Results showed that pH value in the hydrolysis reactor using SEWS (Steam-exploded wheat straw) was lower and increased slowly to 7 in 25 days. In methanogenesis reactors using SEWS and NPWS, pH value was all around 7, which is most suitable to produce methane. In the digestion system using SEWS, the content of TS (Total solid) and VS (Volatile solid) decreased by 57.5% and by 62.1%, respectively, about twice as high as NWPS. The degradation rate of cellulose and semi-cellulose of SEWS were 63.0% and 67.4%, respectively, much higher than NPWS. The degradation rate of the lignin is similar and about 5 %. The total

  7. PEG-modified Penicillin Acylase and Its Partitioning in Aqueous Two-phase Bioconversion System%PEG修饰青霉素酰化酶及其在两水相生物转化体系中的分配

    Institute of Scientific and Technical Information of China (English)

    何汉平; 刘叶青; 曹学君; 张秀萍

    2001-01-01

    Polyethyleneglycol (PEG) activated by tosyl chloride was used to modify penicillin acylase (PAC). The stability of the PEG-PAC was much better than the free PAC. The activity of the modified enzyme was 75% of free enzyme. The partition of PEG-PAC in aqueous two-phase system was investigated. The modified penicillin acylase was mainly present in the PEG phase in a PEG-dextran aqueous two-phase system, and the partition coefficient was 25.%采用对甲苯磺酰氯法,用聚乙二醇对青霉素酰化酶进行化学修饰,修饰酶的比活为未修饰酶的75%,稳定性比游离酶有了很大提高。酶在带修饰酶的聚乙二醇与葡聚糖组成的两水相体系中的分配系数为25。

  8. Mechanical behavior of shock-wave consolidated nano and micron-sized aluminum/silicon carbide and aluminum/aluminum oxide two-phase systems characterized by light and electron metallography

    Science.gov (United States)

    Alba-Baena, Noe Gaudencio

    This dissertation reports the results of the exploratory study of two-phase systems consisting of 150 microm diameter aluminum powder mechanically mixed with 30 nm and 30 microm diameter SiC and Al2O3 powders (in volume fractions of 2, 4, and 21 percent). Powders were mechanically mixed and green compacted to ˜80% theorical density in a series of cylindrical fixtures (steel tubes). The compacted arrangements were explosively consolidated using ammonium nitrate-fuel oil (ANFO) to form stacks of two-phase systems. As result, successfully consolidated cylindrical monoliths of 50 mm (height) x 32 mm (in diameter) were obtained. By taking advantage of the use of SWC (shock wave consolidation) and WEDM (wire-electric discharge machining), the heterogeneous systems were machined in a highly efficiency rate. The sample cuts used for characterization and mechanical properties testing, require the use of less that 10cc of each monolith, in consequence there was preserved an average of 60% of the obtained system monoliths. Consolidated test cylinders of the pure Al and two-phase composites were characterized by optical metallography and TEM. The light micrographs for the five explosively consolidated regimes: aluminum powder, nano and micron-sized Al/Al2O3 systems, and the nano and micron-sized Al/SiC systems exhibit similar ductility in the aluminum grains. Low volume fraction systems exhibit small agglomerations at the grain boundaries for the Al/Al2O3 system and the Al/SiC system reveal a well distributed phase at the grain boundaries. Large and partially bonded agglomerations were observable in the nano-sized high volume fraction (21%) systems, while the micron-sized Al/ceramic systems exhibit homogeneous distribution along the aluminum phase grains. TEM images showed the shock-induced dislocation cell structure, which has partially recrystallized to form a nano grain structure in the consolidated aluminum powder. Furthermore, the SiC nano-agglomerates appeared to have

  9. Ecoulements diphasiques instables dans les systèmes pipeline/riser Unsteady Two-Phase Flows in Pipeline/Riser Systems

    Directory of Open Access Journals (Sweden)

    Fabre J.

    2006-11-01

    Full Text Available Les instabilités hydrodynamiques de l'écoulement dans les systèmes pipeline/riser ont été étudiées sur une boucle d'essais en tubes transparents de diamètre intérieur 0,053 m, longueur 25 m pour la partie pipeline et 13,5 m pour la partie riser. Les expériences effectuées sur de l'eau et de l'air, à différentes pentes du pipeline et pour plusieurs valeurs du débit d'entrée, ont permis l'observation d'instabilités à grande échelle à faible débit de liquide et de gaz. Les cartes de configuration d'écoulement ont été établies pour trois pentes différentes du pipeline. Le modèle numérique développé à partir de ces données résout les équations locales instantanées de bilan de masse et de quantité de mouvement de ces écoulements par la méthode des caractéristiques. L'évolution des pressions, fraction de vide, débit de gaz et de liquide au cours du temps, prévue par le modèle, est généralement en bon accord avec les données expérimentales. Hydrodynamic instabilities of flow in pipeline/riser systems were studied on a test loop made of transparent tubes with an ID of 0. 053 m and 25 m long for the pipeline part and 13. 5 m long for the riser. Experiments performed with water and air, with different slopes of the pipeline and with several inlet flow rates, reveal large-scale instabilities at low liquid and gas flow rates. Flow configuration maps were compiled for three different pipeline slopes. The numerical model developed from these data solves instantaneous local equations for the mass balance and amount of movement of such flows by the method of characteristics. Variations in pressures, in the void fraction and in gas and liquid flow in the time forecast by the model are generally in good agreement with experimental data.

  10. Cell-laden microgel prepared using a biocompatible aqueous two-phase strategy.

    Science.gov (United States)

    Liu, Yang; Nambu, Natalia Oshima; Taya, Masahito

    2017-09-01

    Microfluidic methods are frequently used to produce cell-laden microgels for various biomedical purposes. Such microfluidic methods generally employ oil-water systems. The poor distribution of crosslinking reagents in the oil phase limits the available gelation strategies. Extracting the microgel from the oil-phase also reduces its production efficiency. In this study, an aqueous two-phase system (ATPS) involving dextran (DEX) and polyethylene glycol (PEG) was used to prepare cell-laden microgel. This avoided the problems associated with an oil phase. The microgel precursor polymers and crosslinking reagents were dispersed in the DEX and PEG phases, respectively. The ultra-low interfacial tension of the ATPS hindered droplet formation. A co-flow microfluidic device was fabricated to overcome this problem. The device incorporated a square-wave-changing injection force, to improve the efficiency of droplet formation. The microgel precursor (including alginate and carboxymethyl cellulose derivatives possessing phenolic hydroxyl moieties) could be dispersed in the DEX solution at various concentrations. Uniform droplets were formed with controllable diameters, and were sequentially converted to microgel by horseradish peroxidase-catalyzed crosslinking. Cells were dispersed in the DEX phase with the microgel precursor polymer, and retained their high viability and proliferation in the resulting microgel. The solubility of gelatin derivatives in the DEX phase was low, but was sufficient to impart cell adhesion properties on the microgel.

  11. Integrated downstream processing of lactoperoxidase from milk whey involving aqueous two-phase extraction and ultrasound-assisted ultrafiltration.

    Science.gov (United States)

    Nandini, K E; Rastogi, Navin K

    2011-01-01

    The present work involves the adoption of an integrated approach for the purification of lactoperoxidase from milk whey by coupling aqueous two-phase extraction (ATPE) with ultrasound-assisted ultrafiltration. The effect of system parameters of ATPE such as type of phase system, polyethylene glycol (PEG) molecular mass, system pH, tie line length and phase volume ratio was evaluated so as to obtain differential partitioning of contaminant proteins and lactoperoxidase in top and bottom phases, respectively. PEG 6000-potassium phosphate system was found to be suitable for the maximum activity recovery of lactoperoxidase 150.70% leading to 2.31-fold purity. Further, concentration and purification of enzyme was attempted using ultrafiltration. The activity recovery and purification factor achieved after ultrafiltration were 149.85% and 3.53-fold, respectively. To optimise productivity and cost-effectiveness of integrated process, influence of ultrasound for the enhancement of permeate flux during ultrafiltration was also investigated. Intermittent use of ultrasound along with stirring (2 min acoustic and 2 min stirring) resulted in increased permeate flux from 0.94 to 2.18 l/m(2) h in comparison to the ultrafiltration without ultrasound. The use of ultrasound during ultrafiltration resulted in increase in flux, but there was no significant change in activity recovery and purification factor. The integrated approach involving ATPE and ultrafiltration may prove to be a feasible method for the downstream processing of lactoperoxidase from milk whey.

  12. One-pot synthesis of glutathione by a two-enzyme cascade using a thermophilic ATP regeneration system.

    Science.gov (United States)

    Zhang, Xing; Wu, Hui; Huang, Bing; Li, Zhimin; Ye, Qin

    2017-01-10

    In vitro cascade catalysis using enzyme-based system is becoming a promising biomanufacturing platform for biofuels and biochemicals production. Glutathione is a pivotal non-protein thiol compound and widely applied in food and pharmaceutical industries. In this study, glutathione was synthesized by a bifunctional glutathione synthetase together with a thermophilic ATP regeneration system through a two-enzyme cascade in vitro. Four bifunctional glutathione synthetases from Streptococcus sanguinis, S. gordonii, S. uberis and Bacillus cereus were applied for glutathione synthesis. The bifunctional glutathione synthetase from S. sanguinis was selected and coupled with the polyphosphate kinase from Thermosynechococcus elongatus BP-1 for regenerating ATP to produce glutathione in one pot. In the optimized system, 28.5mM glutathione was produced within 5h due to efficient ATP regeneration from low-cost polyphosphate. The yield based on added l-cysteine reached 81.4% and the productivity of glutathione achieved 5.7mM/h. The one-pot system indicated a potential biotransformation platform for industrial production of glutathione. Copyright © 2016 Elsevier B.V. All rights reserved.

  13. Extraction of Doxycycline Hydrochloride Using Alcohol and Ionic Liquid Binary Aqueous Two Phase System%醇与离子液体二元双水相体系萃取盐酸多西环素

    Institute of Scientific and Technical Information of China (English)

    关卫省; 黎文娟; 韩娟

    2012-01-01

    Based on the molecular alcohol aqueous two-phase system and the ionic liquid aqueous two-phase system, the new method of using n-propanol and hydrophilic ionic liquid(1-butyl-3-methylimidazolium tetrafluoroborate, [Bmim]BF4) with (NH4)2SO4 binary aqueous two phase system for the extraction of doxycycline hydrochloride was developed. The influence factors on partition behaviors of doxycycline hydrochloride were studied, including concentration of (NH4)2SO4, n-propanol con-sumption, pH value, concentration of ionic liquid and doxycycline hydrochloride. The results showed that when using pH value of 4. 0 - 5. 0, (NH4) 2SO4 concentration of 34% and doxycycline hydrochloride concentration between 25 -95 mg/L, the extraction rate and distribution coefficient of doxycycline hydrochloride will be up to 90. 26% -95. 71% and 62. 452 - 149. 401, respectively.%基于小分子醇双水相体系和离子液体双水相体系,建立了正丙醇与亲水性离子液体1-丁基-3-甲基咪唑四氟硼酸[ Bmim]BF4和(NH4 )2SO4形成的二元双水相体系萃取盐酸多西环素的新方法.考察了(NH4)2SO4含量、正丙醇用量、pH值、离子液体含量以及盐酸多西环素含量对盐酸多西环素分配行为的影响.结果表明:当醇和离子液体二元双水相体系的pH值在4.0~5.0范围内,(NH4)2SO4含量为34%,且盐酸多西环素的质量浓度在25 ~ 95 mg/L之间时,该体系对盐酸多西环素的萃取率可达90.26% ~95.71%,分配系数可达62.452 ~ 149.401.

  14. Continuous aqueous two-phase extraction of human antibodies using a packed column.

    Science.gov (United States)

    Rosa, P A J; Azevedo, A M; Sommerfeld, S; Bäcker, W; Aires-Barros, M R

    2012-01-01

    The performance of a pilot scale packed differential contactor was evaluated for the continuous counter-current aqueous two-phase extraction (ATPE) of human immunoglobulin G (IgG) from a Chinese hamster ovary (CHO) cells supernatant (CS) enriched with pure protein. Preliminary studies have been firstly performed in order to select the dispersed phase (phosphate-rich or polyethylene glycol 3350 Da (PEG)-rich phase) and the column packing material. The PEG-rich phase has been selected as the dispersed phase and the stainless steel as the preferred material for the column packing bed since it was not wetted preferentially by the selected dispersed phase. Hydrodynamic studies have been also performed, and the experimental results were successfully adjusted to the Richardson-Zaki and Mísek equations, typically used for the conventional organic-aqueous two-phase systems. An experimental set-up combining the packed column with a pump mixer-settler stage showed to have the best performance and to be advantageous when compared to the IgG batch extraction. An IgG recovery yield of 85% could be obtained with about 50% of total contaminants and more than 85% of contaminant proteins removal. Mass transfer studies have revealed that the mass transfer was controlled by the PEG-rich phase. A higher efficiency could be obtained when using an extra pump mixer-settler stage and higher flow rates.

  15. Development of two-phase measuring systems for comparative invstigations of transient flow in pipelines. Final report; Entwicklung von Zweiphasenmesstechnik fuer vergleichende Untersuchungen zur Beschreibung von transienten Stroemungen in Rohrleitungen. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Prasser, H.M.; Boettger, A.; Zschau, J.

    1999-02-01

    Transient two-phase flow phenomena in pipelines and pipe segments were investigated in an open-air shock pressure test facility specially constructed by the Fraunhofer Insitute of Environmental, Safety and Energy Engineering, Oberhausen (Fraunhofer-Institut fuer Umelt, Sicherheits- und Energietechnik e.V. - UMSICHT). For a better measurement of pressure shock phenomena, the plant was equipped with pressure and power meters. FZR constructed and installed the two-phase measuring sstems, i.e. conductivity and ultrasonic measuring systems, and cooperated in the experiments and their interpretation. To this end, the FZR facility was equipped with 16 needle-shaped conductivity sensors, a novel grid sensor measuring system, and ultrasonic probes. The report describes the technical systems, the trial operation at the Rossendorf test facility, and the experiments in the Oberhausen facility. The experimental results are presented and interpreted. [Deutsch] Fuer die Untersuchung von transienten Zweiphasenstroemungen in Rohrleitungen, bzw. Rohrleitungssegmenten wurde im Fraunhofer-Institut fuer Umwelt, Sicherheits- und Energietechnik e.V. Oberhausen (UMSICHT) eine Druckstossanlage als Freiluftanlage errichtet. Zur experimentellen Beschreibung der Druckstossphaenomene wurde die Anlage neben der Betriebsinstrumentierung zur Einstellung der Betriebsparameter von UMSICHT mit Druck- und Kraftmessgebern ausgeruestet. Aufgabe des FZR war die Instrumentierung der Anlage mit Zweiphasenmesstechnik bestehend aus Leitfaehigkeits- und Ultraschallmesstechnik sowie der Mitwirkung bei den experimentellen Untersuchungen und deren Interpretation. Dazu wurde die Anlage von FZR mit 16 nadelfoermigen Leitfaehigkeitssonden, einem neuartigen Gittersensor-Messsystem und Ultraschall-Aufnehmern ausgeruestet. In dem Bericht wird die eingesetzte Messtechnik und deren Erprobung an der Rossendorfer Versuchsschleife, sowie der Einsatz an der Anlage in Oberhausen beschrieben. Anhand in Zusammenarbeit mit

  16. Discussion of ATP bioluminescence detection system%三磷酸腺苷生物荧光检测系统应用管理

    Institute of Scientific and Technical Information of China (English)

    张亮

    2015-01-01

    Objective: Through the introduction of the application background of ATP bioluminescence detection system, the technical principle and the factors of ATP bioluminescence detection system should be taken into account in the procurement, prompted the personnel understand the necessity of ATP bioluminescence detection system using, help procurement staffs purchasing suitable ATP bioluminescence detection system. Methods: introduces the application of ATP bioluminescence detection system background, technical principle and ATP bioluminescence detection system detection accuracy related factors, and gives reasonable purchase suggestions. Results:Improved procurement staffs’ understand to ATP bioluminescence detection system. Conclusion:ATP bioluminescence detection system as a new kind of detection system, with high sensitivity, simple and quick operation, become auxiliary tool of the various departments to conduct self-detection, hospital infection management department to check, understand the principle of technology of ATP bioluminescence detection system and ATP bioluminescence detection system detection accuracy related factors to help procurement staffs purchase the most suitable ATP bioluminescence detection system for clinical.%目的:通过介绍三磷酸腺苷(ATP)生物荧光检测系统的应用背景、技术原理及设备引进中需参考的重要技术参数,了解ATP生物荧光检测系统使用的必要性,帮助医院选择合适的ATP生物荧光检测系统。方法:介绍ATP生物荧光检测系统的应用背景、技术原理及检测准确性相关的因素,给出合理建议。结果:提高了设备管理部门对ATP生物荧光检测系统的认识。结论:ATP生物荧光检系统作为一种新型的检测系统,以高灵敏度、简单快捷的操作,成为医院感染控制的有效技术手段。了解其技术原理及检测准确性相关的因素,能帮助设备管理部门选择最适合

  17. Experimental and CFD-PBM approach coupled with a simplified dynamic analysis of mass transfer in phenol biodegradation in a three phase system of an aerated two-phase partitioning bioreactor for environmental applications

    Science.gov (United States)

    Moradkhani, Hamed; Anarjan Kouchehbagh, Navideh; Izadkhah, Mir-Shahabeddin

    2017-03-01

    A three-dimensional transient modeling of a two-phase partitioning bioreactor, combining system hydrodynamics, two simultaneous mass transfer and microorganism growth is modeled using computational fluid dynamics code FLUENT 6.2. The simulation is based on standard "k-ɛ" Reynolds-averaged Navier-Stokes model. Population balance model is implemented in order to describe gas bubble coalescence, breakage and species transport in the reaction medium and to predict oxygen volumetric mass transfer coefficient (kLa). Model results are verified against experimental data and show good agreement as 13 classes of bubble size is taking into account. Flow behavior in different operational conditions is studied. Almost at all impeller speeds and aeration intensities there were acceptable distributions of species caused by proper mixing. The magnitude of dissolved oxygen percentage in aqueous phase has a direct correlation with impeller speed and any increasing of the aeration magnitude leads to faster saturation in shorter periods of time.

  18. Experimental and CFD-PBM approach coupled with a simplified dynamic analysis of mass transfer in phenol biodegradation in a three phase system of an aerated two-phase partitioning bioreactor for environmental applications

    Science.gov (United States)

    Moradkhani, Hamed; Anarjan Kouchehbagh, Navideh; Izadkhah, Mir-Shahabeddin

    2016-07-01

    A three-dimensional transient modeling of a two-phase partitioning bioreactor, combining system hydrodynamics, two simultaneous mass transfer and microorganism growth is modeled using computational fluid dynamics code FLUENT 6.2. The simulation is based on standard "k-ɛ" Reynolds-averaged Navier-Stokes model. Population balance model is implemented in order to describe gas bubble coalescence, breakage and species transport in the reaction medium and to predict oxygen volumetric mass transfer coefficient (kLa). Model results are verified against experimental data and show good agreement as 13 classes of bubble size is taking into account. Flow behavior in different operational conditions is studied. Almost at all impeller speeds and aeration intensities there were acceptable distributions of species caused by proper mixing. The magnitude of dissolved oxygen percentage in aqueous phase has a direct correlation with impeller speed and any increasing of the aeration magnitude leads to faster saturation in shorter periods of time.

  19. Effects of Geometric Parameter on Performance of Ejector and Two-phase Ejector Refrigeration System%几何参数对引射器及两相流引射制冷系统性能的影响

    Institute of Scientific and Technical Information of China (English)

    裴文伟; 郭宪民; 王善云; 郭欣炜

    2013-01-01

    In order to increase the coefficient of performance (COP) of the refrigeration system , the expansion valve is replaced by a two-phase ejector in the two-phase ejector refrigeration cycle to recover the potential energy of the high pressure refrigerant. The performance of two-phase ejector refrigeration system with refrigerant R134a as working fluid is experimentally investigated. The effects of the throat diameter of the nozzle and the diameter of the mixing chamber on the performance of the ejector and the two-phase ejector refrigeration cycle system were analyzed. The experimental results indicate that there is an optimal combination of the nozzle throat diameter and the mixing chamber diameter to maximize the entrainment ratio under a fixed working condition. The entrainment ratio of the ejector reaches to the maximum value with the throat diameter of 2.0mm and the mixing chamber diameter of 16mm under the conditions of 3℃ evaporating temperature and 55℃ condensing temperature. Under a fixed working condition, the optimal combination of the nozzle throat diameter and the mixing chamber diameter for maximum of the entrainment ratio is not consistent with the one for maximum of the COP of the refrigeration system. This may be caused by the shocks in the ejector, which should be investigated deeply.%  用两相流引射器代替膨胀阀,可回收两相流引射制冷循环中高压工质的压力能,提高制冷系统效率.对以R134a为工质的两相流引射制冷系统性能进行了实验研究,分析了喷嘴喉部直径和混合室直径对R134a两相流引射器及引射制冷系统性能的影响.实验结果表明,在固定工况条件下,存在使引射比达到最大的最佳喷嘴喉部直径和混合室直径组合.在蒸发温度为3℃、冷凝温度为55℃的工况下,当喷嘴喉部直径为2.0mm、混合室直径为16mm时引射器的引射比最大.在固定工况条件下,使引射比达到最大值的喷嘴喉部直

  20. Study on treatment of phenolic compounds in cokery wastewater by propyl-alcohol ammonium sulfate aqueous two-phase system%醇-盐双水相技术去除废水中的酚类物质

    Institute of Scientific and Technical Information of China (English)

    曹文; 高云涛; 王红斌; 李孔明; 马存娇

    2009-01-01

    A novel method for treatment of phenolic compounds in cokery wastewater by propyl-alcohol ammonium sulfate aqueous two-phase system was investigted.The effects of the amount of ammonium sulfate used,the amount of propyl-alcohol used,pH value on extractield was studied.Extraction was optimized using a L9(34)orthogonal test.The results indicated optimum extraction conditions were the amount of ammonium sulfate used of 18.0 g,the amount of propyl-alcohol used of 16 mL,and pH value of 3.0.A extraction yield of 99.37% was achived under optimum extraction conditions and via secondary extraction.

  1. 异丙醇/盐双水相分离制备高色价栀子黄%Separation of Gardenia Yellow by Isopropanol Alcohol/Salt Aqueous Two-Phase System

    Institute of Scientific and Technical Information of China (English)

    郭晶莹; 张红萍

    2016-01-01

    Abstrat:Gardenia yellow was separated by employing isopropanol-salt aqueous two-phase system. The factors such as kinds of salt, concentration of the salt, pH and temperture on the gardenia yellow separation efficiency were investigated, and the gardenia yellow was analyzed by spectrophotometric method and HPLC. The results showed that the aqueous two-phase system which was formed by isopropanol alcohol(2mL) and sodium citrate (1.6g)was effective for the separation of gardenia yellow from gardenia fruit in 35℃and pH=8.7,and the color value and the OD of the gardenia yellow were 542 and 0.382,respectively.%采用异丙醇/盐组成的双水相体系分离栀子黄。综合考察了盐的种类、浓度、pH值和温度等因素对栀子黄分离效果的影响,并且采用紫外-可见分光光度法和HPLC对异丙醇/盐双水相体系分离得到的栀子黄进行评价。结果表明,在35℃条件下由1.6g的柠檬酸三钠和2mL的异丙醇组成双水相体系,pH等于8.7,分离得到栀子黄和OD值分别为0.382、542。

  2. Study on Extraction Process Conditions of Rice Bran Polysaccharide by Aqueous Two-phase System%双水相萃取米糠多糖工艺条件的探究

    Institute of Scientific and Technical Information of China (English)

    秦微微; 金婷; 宋学东; 丁振铎; 张衡

    2014-01-01

    旨在探究聚乙二醇/硫酸铵双水相体系萃取米糠中多糖成分的最佳条件。以双水相系统的相比、分配系数、收率等为参数,探究了PEG 的相对分子质量、PEG 的质量分数以及硫酸铵质量分数对米糠多糖在两相系统中的分配行为的影响。结果表明:萃取最佳条件为PEG分子量为6000,硫酸铵质量分数为14.8%,PEG 6000质量分数为14.3%,多糖得率为0.826388。%The aqueous two-phase system of polyethylene glycol (PEG)/ammonium sulfate for extrac-tion of polysaccharide in rice bran is studied.Use the parameters such as the volume ratio of two pha-ses,the distribution coefficient and the yield to explore the effects of the molecular weight of PEG, the mass fraction of ammonium sulfate and PEG on distribution behavior of polysaccharide of rice bran in two-phase system.It is demonstrated that the optimum conditions of extraction are as follows:the molecular weight of PEG is 6000,the mass fraction of ammonium sulfate is 14.8%,the mass fraction of PEG 6000 is 14.3%,and the yield of polysaccharide is 0.826388.

  3. Study of two-phase flows in reduced gravity

    Science.gov (United States)

    Roy, Tirthankar

    Study of gas-liquid two-phase flows under reduced gravity conditions is extremely important. One of the major applications of gas-liquid two-phase flows under reduced gravity conditions is in the design of active thermal control systems for future space applications. Previous space crafts were characterized by low heat generation within the spacecraft which needed to be redistributed within the craft or rejected to space. This task could easily have been accomplished by pumped single-phase loops or passive systems such as heat pipes and so on. However with increase in heat generation within the space craft as predicted for future missions, pumped boiling two-phase flows are being considered. This is because of higher heat transfer co-efficients associated with boiling heat transfer among other advantages. Two-phase flows under reduced gravity conditions also find important applications in space propulsion as in space nuclear power reactors as well as in many other life support systems of space crafts. Two-fluid model along with Interfacial Area Transport Equation (IATE) is a useful tool available to predict the behavior of gas-liquid two-phase flows under reduced gravity conditions. It should be noted that considerable differences exist between two-phase flows under reduced and normal gravity conditions especially for low inertia flows. This is because due to suppression of the gravity field the gas-liquid two-phase flows take a considerable time to develop under reduced gravity conditions as compared to normal gravity conditions. Hence other common methods of analysis applicable for fully developed gas-liquid two-phase flows under normal gravity conditions, like flow regimes and flow regime transition criteria, will not be applicable to gas-liquid two-phase flows under reduced gravity conditions. However the two-fluid model and the IATE need to be evaluated first against detailed experimental data obtained under reduced gravity conditions. Although lot of studies

  4. 48 CFR 36.301 - Use of two-phase design-build selection procedures.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Use of two-phase design... ACQUISITION REGULATION SPECIAL CATEGORIES OF CONTRACTING CONSTRUCTION AND ARCHITECT-ENGINEER CONTRACTS Two-Phase Design-Build Selection Procedures 36.301 Use of two-phase design-build selection procedures....

  5. Economic analysis of uricase production under uncertainty: Contrast of chromatographic purification and aqueous two-phase extraction (with and without PEG recycle).

    Science.gov (United States)

    Torres-Acosta, Mario A; Aguilar-Yáñez, José M; Rito-Palomares, Marco; Titchener-Hooker, Nigel J

    2016-01-01

    Uricase is the enzyme responsible for the breakdown of uric acid, the key molecule leading to gout in humans, into allantoin, but it is absent in humans. It has been produced as a PEGylated pharmaceutical where the purification is performed through three sequential chromatographic columns. More recently an aqueous two-phase system (ATPS) was reported that could recover Uricase with high yield and purity. Although the use of ATPS can decrease cost and time, it also generates a large amount of waste. The ability, therefore, to recycle key components of ATPS is of interest. Economic modelling is a powerful tool that allows the bioprocess engineer to compare possible outcomes and find areas where further research or optimization might be required without recourse to extensive experiments and time. This research provides an economic analysis using the commercial software BioSolve of the strategies for Uricase production: chromatographic and ATPS, and includes a third bioprocess that uses material recycling. The key parameters that affect the process the most were located via a sensitivity analysis and evaluated with a Monte Carlo analysis. Results show that ATPS is far less expensive than chromatography, but that there is an area where the cost of production of both bioprocesses overlap. Furthermore, recycling does not impact the cost of production. This study serves to provide a framework for the economic analysis of Uricase production using alternative techniques.

  6. Velocity and energy relaxation in two-phase flows

    CERN Document Server

    Meyapin, Yannick; Gisclon, Marguerite

    2009-01-01

    In the present study we investigate analytically the process of velocity and energy relaxation in two-phase flows. We begin our exposition by considering the so-called six equations two-phase model [Ishii1975, Rovarch2006]. This model assumes each phase to possess its own velocity and energy variables. Despite recent advances, the six equations model remains computationally expensive for many practical applications. Moreover, its advection operator may be non-hyperbolic which poses additional theoretical difficulties to construct robust numerical schemes |Ghidaglia et al, 2001]. In order to simplify this system, we complete momentum and energy conservation equations by relaxation terms. When relaxation characteristic time tends to zero, velocities and energies are constrained to tend to common values for both phases. As a result, we obtain a simple two-phase model which was recently proposed for simulation of violent aerated flows [Dias et al, 2010]. The preservation of invariant regions and incompressible li...

  7. Inhibition by corrins of the ATP-dependent activation and CO2 reduction by the methylreductase system in Methanobacterium bryantii.

    Science.gov (United States)

    Whitman, W B; Wolfe, R S

    1987-01-01

    Corrins inhibited the ATP-dependent activation of the methylreductase system and the methyl coenzyme M-dependent reduction of CO2 in extracts of Methanobacterium bryantii resolved from low-molecular-weight factors. The concentrations of cobinamides and cobamides required for one-half of maximal inhibition of the ATP-dependent activation were between 1 and 5 microM. Cobinamides were more inhibitory at lower concentrations than cobamides. Deoxyadenosylcobalamin was not inhibitory at concentrations up to 25 microM. The inhibition of CO2 reduction was competitive with respect to CO2. The concentration of methylcobalamin required for one-half of maximal inhibition was 5 microM. Other cobamides inhibited at similar concentrations, but diaquacobinamide inhibited at lower concentrations. With respect to their affinities and specificities for corrins, inhibition of both the ATP-dependent activation and CO2 reduction closely resembled the corrin-dependent activation of the methylreductase described in similar extracts (W. B. Whitman and R. S. Wolfe, J. Bacteriol. 164:165-172, 1985). However, whether the multiple effects of corrins are due to action at a single site is unknown. PMID:3098736

  8. 76 FR 13069 - Airworthiness Directives; BAE Systems (Operations) Limited Model ATP Airplanes; BAE Systems...

    Science.gov (United States)

    2011-03-10

    ..., United Kingdom; telephone +44 1292 675207; fax +44 1292 ] 675704; e-mail RApublications@baesystems.com... control surface, the hinge pins are punched out of the hinges. Investigations have concluded that, after... control surface hinge pin had migrated out of position, causing a rubbing contact. BAE Systems responded...

  9. Determination of Sudan I-IV in candy using ionic liquid/anionic surfactant aqueous two-phase extraction coupled with high-performance liquid chromatography.

    Science.gov (United States)

    Yu, Wei; Liu, Zhongling; Li, Qiang; Zhang, Hanqi; Yu, Yong

    2015-04-15

    Ionic liquid/anionic surfactant aqueous two-phase system was developed and applied for the extraction of Sudan I-IV. High-performance liquid chromatography was applied to the determination of the analytes. The aqueous two-phase system (ATPS) was formed in the present of C4[MIM]BF4, sodium dodecyl benzene sulphonate and (NH4)2SO4. The parameters affecting the extraction efficiency, such as volume of ionic liquid, amount of sodium dodecyl benzene sulphonate, ionic strength, pH value of system, extraction time and temperature were investigated. The limits of detection for Sudan I, II, III and IV were 5.45, 4.66, 3.68, 4.20 μg kg(-1), respectively. When the present method was applied to the analysis of candy samples, the recoveries of the analytes ranged from 82.3% to 112.1% and relative standard deviations were lower than 7.41%.

  10. Evaluation of Grounding Impedance of a Complex Lightning Protective System Using Earth Ground Clamp Measurements and ATP Modeling

    Science.gov (United States)

    Mata, Carlos T.; Rakov, V. A.; Mata, Angel G.

    2010-01-01

    A new Lightning Protection System (LPS) was designed and built at Launch Complex 39B (LC39B), at the Kennedy Space Center (KSC), Florida, which consists of a catenary wire system (at a height of about 181 meters above ground level) supported by three insulators installed atop three towers in a triangular configuration. A total of nine downconductors (each about 250 meters long, on average) are connected to the catenary wire system. Each of the nine downconductors is connected to a 7.62-meter radius circular counterpoise conductor with six equally spaced 6-meter long vertical grounding rods. Grounding requirements at LC39B call for all underground and above ground metallic piping, enclosures, raceways, and cable trays, within 7.62 meters of the counterpoise, to be bounded to the counterpoise, which results in a complex interconnected grounding system, given the many metallic piping, raceways, and cable trays that run in multiple direction around LC39B. The complexity of this grounding system makes the fall of potential method, which uses multiple metallic rods or stakes, unsuitable for measuring the grounding impedances of the downconductors. To calculate the downconductors grounding impedance, an Earth Ground Clamp (a stakeless grounding resistance measuring device) and a LPS Alternative Transient Program (ATP) model are used. The Earth Ground Clamp is used to measure the loop impedance plus the grounding impedance of each downconductor and the ATP model is used to calculate the loop impedance of each downconductor circuit. The grounding impedance of the downconductors is then calculated by subtracting the ATP calculated loop impedances from the Earth Ground Clamp measurements.

  11. Functional expression of phosphagen kinase systems confers resistance to transient stresses in Saccharomyces cerevisiae by buffering the ATP pool.

    Science.gov (United States)

    Canonaco, Fabrizio; Schlattner, Uwe; Pruett, Pamela S; Wallimann, Theo; Sauer, Uwe

    2002-08-30

    Phosphagen kinase systems provide different advantages to tissues with high and fluctuating energy demands, in particular an efficient energy buffering system. In this study we show for the first time functional expression of two phosphagen kinase systems in Saccharomyces cerevisiae, which does not normally contain such systems. First, to establish the creatine kinase system, in addition to overexpressing creatine kinase isoenzymes, we had to install the biosynthesis pathway of creatine by co-overexpression of L-arginine:glycine amidinotransferase and guanidinoacetate methyltransferase. Although we could achieve considerable creatine kinase activity, together with more than 3 mM intracellular creatine, this was not sufficient to confer an obvious advantage to the yeast under the specific stress conditions examined here. Second, using arginine kinase, we successfully installed an intracellular phosphagen pool of about 5 mM phosphoarginine. Such arginine kinase-expressing yeast showed improved resistance under two stress challenges that drain cellular energy, which were transient pH reduction and starvation. Although transient starvation led to 50% reduced intracellular ATP concentrations in wild-type yeast, arginine kinase overexpression stabilized the ATP pool at the pre-stress level. Thus, our results demonstrate that temporal energy buffering is an intrinsic property of phosphagen kinases that can be transferred to phylogenetically very distant organisms.

  12. Two-Phase Cavitating Flow in Turbomachines

    Directory of Open Access Journals (Sweden)

    Sandor I. Bernad

    2012-11-01

    Full Text Available Cavitating flows are notoriously complex because they are highly turbulent and unsteady flows involving two species (liquid/vapor with a large density difference. These features pose a unique challenge to numerical modeling works. The study briefly reviews the methodology curently employed for industrial cavitating flow simulations using the two-phase mixture model. The two-phase mixture model is evaluated and validated using benchmark problem where experimental data are available. A 3D cavitating flow computation is performed for the GAMM Francis runner. The model is able to qualitatively predict the location and extent of the 3D cavity on the blade, but further investigation are needed to quatitatively assess the accuracy for real turbomachinery cavitating flows.

  13. On the modelling and the analysis of two-phase flow instabilities in pipeline-riser systems; Modelisation et analyse des instabilites d'ecoulements diphasiques dans les conduites petrolieres du type pipeline-riser

    Energy Technology Data Exchange (ETDEWEB)

    Zakarian, E.

    2000-03-10

    Recent estimations predict that over half the remaining offshore oil and gas reserves are located in deep water and marginal fields. For such reserves, economic recovery methods are required. Then, multiphase flows are transported within pipelines and separated on treatment platforms built in shallow water or processed in onshore facilities. Unfortunately, hydrodynamic instabilities may occur whenever gas and liquid flow in a pipeline, generating serious operating problems. This dissertation presents a new way to model two-phase flows in pipelines such as pipeline-riser systems. Equations are algebraic and differential. Their smoothness depends on the closure laws of the problem such as slip or friction laws. Smooth forms of these closure laws are presented for the first time in this dissertation. Therefore, a mathematical analysis of our model fits into a classical frame: a linear analysis leads to an analytical expression of the boundary between stable and unstable flows. A nonlinear analysis provides for the first time, the bifurcation curves of gas-liquid flows in pipe-riser systems, locally round their stability boundary. (author)

  14. Extraction of Solanesol and Nicotine from Inferior Tobacco Leaves by Aqueous Two-phase System%双水相同时提取次烟叶中茄尼醇和烟碱的研究

    Institute of Scientific and Technical Information of China (English)

    刘宝亮; 曹桂萍; 张金涛

    2012-01-01

    The feasibility and technical conditions of the extraction of solanesol and nicotine from inferior tobacco leaves by a new aqueous two-phase system were investigated. An Acetone-DHP (Dipotassium Hydrogen Phosphate) aqueous two-phase system was applied. Factors including the different volume ratio of acetone to water, the addition amount of phosphate,the material liquid ratio,extraction temperature, extraction time and the pH value on the influences of the yield of two substances were studied. The optimized extraction conditions were described as follows: the volume ratio of acetone to water was 5:5,addition amount of phosphate was 3.0 g,material liquid ratio was 0.025 g/mL (0.5 g/20.0 mL) .extraction temperature was 50℃ .extraction time was 4 h and pH was 10.%研究新型双水相体系同时从次等烟丝中提取茄尼醇和烟碱的可行性和工艺条件.新型双水相体系为丙酮-磷酸氢二钾双水相体系,主要研究了丙酮与水不同体积比、磷酸氢二钾的加入量、料液比、浸提温度、浸提时间、双水相体系pH值对茄尼醇和烟碱得率的影响,确定了最佳提取条件:丙酮与水的体积为5:5,磷酸氢二钾的加入量为3.0g,料液比为0.025 g/mL(0.5 g/20.0 mL),浸提温度为50℃,浸提时间为4h,pH值为10.

  15. Critical thinking: a two-phase framework.

    Science.gov (United States)

    Edwards, Sharon L

    2007-09-01

    This article provides a comprehensive review of how a two-phase framework can promote and engage nurses in the concepts of critical thinking. Nurse education is required to integrate critical thinking in their teaching strategies, as it is widely recognised as an important part of student nurses becoming analytical qualified practitioners. The two-phase framework can be incorporated in the classroom using enquiry-based scenarios or used to investigate situations that arise from practice, for reflection, analysis, theorising or to explore issues. This paper proposes a two-phase framework for incorporation in the classroom and practice to promote critical thinking. Phase 1 attempts to make it easier for nurses to organise and expound often complex and abstract ideas that arise when using critical thinking, identify more than one solution to the problem by using a variety of cues to facilitate action. Phase 2 encourages nurses to be accountable and responsible, to justify a decision, be creative and innovative in implementing change.

  16. Gibbs free energy of transfer of a methylene group on {l_brace}UCON + (sodium or potassium) phosphate salts{r_brace} aqueous two-phase systems: Hydrophobicity effects

    Energy Technology Data Exchange (ETDEWEB)

    Silverio, Sara C. [LSRE - Laboratory of Separation and Reaction Engineering, Associate Laboratory LSRE/LCM, Department of Chemical Engineering, Faculty of Engineering, University of Porto, Rua Dr. Roberto Frias s/n. 4200-465 Porto (Portugal); IBB - Institute for Biotechnology and Bioengineering, Centre for Biological Engineering, University of Minho, Campus de Gualtar, 4710-057 Braga (Portugal); Rodriguez, Oscar [LSRE - Laboratory of Separation and Reaction Engineering, Associate Laboratory LSRE/LCM, Department of Chemical Engineering, Faculty of Engineering, University of Porto, Rua Dr. Roberto Frias s/n. 4200-465 Porto. Portugal (Portugal); Teixeira, Jose A. [IBB - Institute for Biotechnology and Bioengineering, Centre for Biological Engineering, University of Minho, Campus de Gualtar, 4710-057 Braga (Portugal); Macedo, Eugenia A., E-mail: eamacedo@fe.up.p [LSRE - Laboratory of Separation and Reaction Engineering, Associate Laboratory LSRE/LCM, Department of Chemical Engineering, Faculty of Engineering, University of Porto, Rua Dr. Roberto Frias s/n. 4200-465 Porto (Portugal)

    2010-08-15

    The Gibbs free energy of transfer of a suitable hydrophobic probe can be regarded as a measure of the relative hydrophobicity of the different phases. The methylene group (CH{sub 2}) can be considered hydrophobic, and thus be a suitable probe for hydrophobicity. In this work, the partition coefficients of a series of five dinitrophenylated-amino acids were experimentally determined, at 23 {sup o}C, in three different tie-lines of the biphasic systems: (UCON + K{sub 2}HPO{sub 4}), (UCON + potassium phosphate buffer, pH 7), (UCON + KH{sub 2}PO{sub 4}), (UCON + Na{sub 2}HPO{sub 4}), (UCON + sodium phosphate buffer, pH 7), and (UCON + NaH{sub 2}PO{sub 4}). The Gibbs free energy of transfer of CH{sub 2} units were calculated from the partition coefficients and used to compare the relative hydrophobicity of the equilibrium phases. The largest relative hydrophobicity was found for the ATPS formed by dihydrogen phosphate salts.

  17. Partitioning behavior and structural characterization of papain in ionic liquid aqueous two-phase system%木瓜蛋白酶在离子液体双水相中的分配行为

    Institute of Scientific and Technical Information of China (English)

    王伟涛; 蒋志国; 张海德; 彭健; 许英豪; 董安华; 杨雪芳; 蒋欣欣

    2015-01-01

    Papain was extracted by ionic liquid aqueous two-phase system. Firstly,the influence of concentration, pH, and temperature of ionic liquid on the activity of papain was investigated. Secondly, the effects of different ionic liquid aqueous two-phase systems, alkyl chain lengths and concentrations of the ionic liquid, dosage of papain, pH, temperature on the partitioning behavior of papain were discussed. [C4mim]Cl and [C4mim]Br systems were better than [C4mim]BF4 system in extraction of papain, and it was disadvantageous to extract papain at a high temperature (60℃or higher). Activity recovery of enzyme reached 95.16%and purification factor reached 1.5 under the optimum conditions:[C4mim]Cl 0.25 g·ml−1, K2HPO4 0.35 g·ml−1, pH 8.0, enzyme addition 2.0 mg·ml−1, 30℃. The result laid the experimental basis for further scale-up research and commercial production.%采用离子液体双水相提取木瓜蛋白酶。首先考察不同浓度、pH、温度的离子液体对木瓜蛋白酶活性的影响,其次考察不同离子液体双水相体系、离子液体侧烷基链长度及浓度、酶添加量、pH、温度对木瓜蛋白酶分配行为的影响。结果表明:[C4mim]Cl 和[C4mim]Br 体系萃取木瓜蛋白酶的效果比[C4mim]BF4体系好;高温(≥60℃)对离子液体双水相体系萃取木瓜蛋白酶不利。离子液体双水相萃取木瓜蛋白酶的最佳工艺条件:0.25 g·ml−1的[C4mim]Cl,0.35 g·ml−1的K2HPO4,pH 8.0,酶添加量2.0 mg·ml−1,30℃。此条件下木瓜蛋白酶的酶活性回收率达到95.16%,纯化因子达到1.5。为今后进一步研究该体系的放大实验或规模化生产奠定了基础。

  18. Partition efficiencies of newly fabricated universal high-speed counter-current chromatograph for separation of two different types of sugar derivatives with organic-aqueous two-phase solvent systems.

    Science.gov (United States)

    Shinomiya, Kazufusa; Sato, Kazuki; Yoshida, Kazunori; Tokura, Koji; Maruyama, Hiroshi; Yanagidaira, Kazuhiro; Ito, Yoichiro

    2013-12-27

    A new design of universal high-speed counter-current chromatograph (HSCCC) was fabricated in our laboratory. It holds a set of four column holders symmetrically around the rotary frame at a distance of 11.2cm from the central axis. By engaging the stationary gear on the central axis of the centrifuge to the planetary gears on the column holder shaft through a set of idle gears, two pairs of diagonally located column holders simultaneously rotate about their own axes in the opposite directions: one forward (type-J planetary motion) and the other backward (type-I planetary motion) each synchronously with the revolution. Using the eccentric coil assembly, partition efficiencies produced by these two planetary motions were compared on the separation of two different types of sugar derivatives (4-methylumbelliferyl and 5-bromo-4-chloro-3-indoxyl sugar derivatives) using organic-aqueous two-phase solvent systems composed of n-hexane/ethyl acetate/1-butanol/methanol/water and aqueous 0.1M sodium tetraborate, respectively. With lower phase mobile, better peak resolution was obtained by the type-J forward rotation for both samples probably due to higher retention of the stationary phase. With upper phase mobile, however, similar peak resolutions were obtained between these two planetary motions for both sugar derivatives. The overall results indicate that the present universal HSCCC is useful for counter-current chromatographic separation since each planetary motion has its specific applications: e.g., vortex CCC by the type-I planetary motion and HSCCC by the type-J planetary motion both for separation of various natural and synthetic products.

  19. Analysis of voltage sag compensation in distribution systems using a multilevel DSTATCOM in ATP/EMTP

    Directory of Open Access Journals (Sweden)

    Herbert Enrique Rojas-Cubides

    2015-01-01

    Full Text Available Los hundimientos de tensión (sags son perturbaciones de calida d de potencia comunes en los sistemas eléctricos. Estos pueden causar daños en equipos sensibles y la interrupción de procesos. El co mpensador estático de distribución (DSTATCOM es un dispositivo que puede compensar sags inyectando potencia reactiva al sistema. E ste artículo muestra la influencia que tiene la conexión de un DSTATCOM de 12-pulsos sobre los sags que se presentan en el sistema de d istribución IEEE-13 modificado. El análisis se realiza mediante la generación aleatoria de perturbaciones usan do una rutina de MATLAB para id entificar los nodos críticos del sistema de prueba. Además, se describe el modelo del DSTATCOM usando lo s elementos disponibles en el s oftware ATP/EMTP. Las simulaciones muestran que cuando el DSTATCOM se conecta al nodo afectado es posible mitigar el sag completamente. Finalmente, se considera la relación entre la po tencia reactiva inyectada por el DSTATCOM, el tipo de sag y la ubicaci ón del nodo afectado.

  20. 一种新型两相励磁开关磁阻电机驱动系统的静态特性%STATIC PERFORMANCE OF A NEW SRD SYSTEM WITH TWO-PHASE EXCITATION

    Institute of Scientific and Technical Information of China (English)

    郭伟; 詹琼华; 丘亦慧

    2002-01-01

    该文主要分析了一种两相同时励磁的开关磁阻电机(SRM)的静态特性.文中首先简要介绍了这种两相励磁系统的结构,然后提出了两相励磁下SRM的磁链模型.基于详细的非线性有限元分析(FEA)的结果,建立了简化的线性模型且利用此线性模型导出了SRM的转矩--转角特性,并和非线性FEA模型下的结果进行了比较.最后,根据FEA的结果,提出了一种优化的控制策略来提高这种SRM的性能.%This paper provides an analysis of a switched reluctance motor (SRM) under two-phase excitation. After a brief introduction of the two-phase excitation scheme, the flux linkage model of a SRM under two-phase excitation is developed using FEA. A linearized model is then established based on the detailed flux linkage analysis. The torque-angle characteristics of such a linear model are compared with that derived from the detailed and nonlinear FEA model. Based on theFEA model, an optimized control strategy is proposed to improve the performanceof the SRM under two-phase excitation.

  1. Droplet Manipulations in Two Phase Flow Microfluidics

    Directory of Open Access Journals (Sweden)

    Arjen M. Pit

    2015-11-01

    Full Text Available Even though droplet microfluidics has been developed since the early 1980s, the number of applications that have resulted in commercial products is still relatively small. This is partly due to an ongoing maturation and integration of existing methods, but possibly also because of the emergence of new techniques, whose potential has not been fully realized. This review summarizes the currently existing techniques for manipulating droplets in two-phase flow microfluidics. Specifically, very recent developments like the use of acoustic waves, magnetic fields, surface energy wells, and electrostatic traps and rails are discussed. The physical principles are explained, and (potential advantages and drawbacks of different methods in the sense of versatility, flexibility, tunability and durability are discussed, where possible, per technique and per droplet operation: generation, transport, sorting, coalescence and splitting.

  2. Infleunce of pH on the partition of glucose-6-phosphate dehydrogenase and hexokinase in aqueous two-phase system Influência do pH na partição da glicose 6-fosfato desidrogenase e hexoquinase em sistema de duas fases aquosas

    Directory of Open Access Journals (Sweden)

    Daniel Pereira da Silva

    2002-09-01

    Full Text Available Glucose-6-phosphate dehydrogenase (G6PDH and hexokinase (HK are important enzymes used in biochemical and medical studies and in several analytical methods. Aqueous two-phase system (ATPS formed by a polymer solution and an electrolyte solution provides a method for the separation and purification of enzymes with several advantages, including biocompatibility and easy scale up of the process. In this work, the effects of different pH values on the storage stability and partitioning behavior (K, partition coefficient of the enzymes G6PDH and HK from baker's yeast extract were investigated in ATPS. The results, obtained from the 17.5% PEG 400 : 15.0% phosphate system, showed that when the pH was increased from 5.0 to 8.8, the K HK increased 26-fold and the K G6PDH 2.2-fold. In the 20.0% PEG 1500 : 17.5% phosphate system, the K HK and K G6PDH increased 13 and 1.2-fold, when the pH value was increased from 3.8 to 8.8, respectively. This leads to the conclusion that the partition coefficient for both enzymes is favored by high pH values. A statistical analysis of the results was conducted to confirm this conclusion.Glicose-6-fosfato desidrogenase (G6PDH e hexoquinase (HK são importantes enzimas usadas em estudos bioquímicos e médicos e em diversos métodos analíticos. Sistema de duas fases aquosas (SDFA formado por uma solução polimérica e uma solução eletrolítica proporciona um método para separação e purificação de enzimas com diversas vantagens, incluindo biocompatibilidade, que pode ser facilmente escalonado para nível industrial. Neste trabalho, os efeitos de diferentes valores de pH na estabilidade e na partição (K, coeficiente de partição por SDFA das enzimas G6PDH e HK, obtidas através de levedura de panificação, foram investigados. Os resultados, obtidos do sistema constituído por 17,5% de PEG 400 e 15,0% de fosfato, mostraram que com a elevação do pH de 5,0 para 8,8, o K HK aumentou 26 vezes e o K G6PDH 2,2 vezes

  3. Effectiveness of onsite wastewater reuse system in reducing bacterial contaminants measured with human-specific IMS/ATP and qPCR.

    Science.gov (United States)

    Agidi, Senyo; Vedachalam, Sridhar; Mancl, Karen; Lee, Jiyoung

    2013-01-30

    Water shortages and the drive to recycle is increasing interest in reuse of reclaimed wastewater. Timely and cost-effective ways to detect fecal pollutants prior to reuse increases confidence of residents and neighbors concerned about reuse of reclaimed wastewater. The on-site wastewater treatment and reuse systems (OWTRS) used in this study include a septic tank, peat bioreactor, ClO(2) disinfection and land spray irrigation system. Bacteroides fragilis, Escherichia coli and Enterococcus spp., were tested with immunomagnetic separation/ATP bioluminescence (IMS/ATP), qPCR and culture-based methods. The results displayed a 2-log reduction in fecal bacteria in the peat bioreactor and a 5-log reduction following chloride dioxide disinfection. The fecal bacteria levels measured by IMS/ATP correlated with qPCR results: HuBac 16S (R(2) = 0.903), Bf-group 16S (R(2) = 0.956), gyrB (R(2) = 0.673), and Ent 23S (R(2) = 0.724). This is the first study in which the newly developed human-specific IMS/ATP and previously developed IMS/ATP were applied for determining OWTRS efficiency. Results of the study revealed that IMS/ATP is a timely and cost-effective way to detect fecal contaminants, and results were validated with qPCR and culture based methods. The new IMS/ATP can also be applied broadly in the detection of human-originated fecal contamination.

  4. Partitioning of Bovine Serum Albumin in Polyethylene Glycol(PEG)/Phosphate Aqueous Two-Phase System%PEG/磷酸盐双水相系统萃取BSA的研究

    Institute of Scientific and Technical Information of China (English)

    胡松青; 李琳; 李冰; 肖蕾

    2002-01-01

    BSA partitioning was performed in the PEG/phosphate aqueous two-phase system. The effects of the phase compositions concentrations, addition of NaCl and the initial concentration of BSA on the partition coefficient K and the fraction of BSA in the bottom phase Y were investigated. The results showed that BSA was enriched to the bottom phase. The phase compositions of PEG 6000 mass fraction is 10%/PO3-4 mass fraction is 6% and PEG 10000 mass fraction is 6%/PO3-4 mass fraction is 6% respectively were desirable for partitioning. The addition of NaCl showed no influence on BSA partitioning in PEG 6000 mass fraction is 10% /PO3-4 mass fraction is 6% system. The mathematical model for K was derived from the initial mass concentration of BSA and well fitting with the experimental data.%以PEG/磷酸盐双水相系统萃取BSA为对象,研究了双水相系统成相浓度、外加盐NaCl、BSA起始浓度等对BSA在两相间的分配系数和BSA下相萃取率的影响.结果发现,BSA大部分被萃取入双水相体系的下相,成相组成为PEG 6000 10% (质量分数)/ PO3-4 6% (质量分数)和PEG 10000 6% (质量分数)/ PO3-4 6% (质量分数)的双水相系统有利于BSA的萃取分配;外加NaCl对PEG 6000 10%(质量分数)/PO3-4 6%(质量分数)系统萃取BSA的影响不大;得出了上、下相BSA浓度和BSA在两相间分配系数K与系统BSA起始浓度之间的表达式,与实验结果有较好的拟合.

  5. For solid-liquid two phase softness abrasive flow embedded real-time monitoring and control system%面向固-液两相软性磨粒流嵌入式实时测控系统

    Institute of Scientific and Technical Information of China (English)

    计时鸣; 兰信鸿

    2012-01-01

    In order to solve the problems of flow pipe is to small to the conventional sensor for solid-liquid two phase softness abrasive flow,a monitoring method based on the vibration signal was proposed. Through the wavelet packet analysis of vibration signal, extraction signal characteristics were gotten. Using object-oriented technology, a kind of measurement and control software framework was developed, combined with finite state machine theory and embedded real-time operating system and programming methods of multitasking. Using Linux and DSP/BIOS RTOS, the double operating system signal processing technology was implemented,a multi-channel high speed data acquisition function was implemented on the intelligence embedded real-time measurement and control platform. The results indicate that it is easy to expand and interactive.%针对固-液两相软性磨粒流精密抛光方法中流道微小,无法采用常规直接信号传感器的问题,提出了一种基于二次信号-加速度振动信号的软性磨粒流监测方法.通过小波包分析提取了振动信号的特征.结合基于有限状态机理论与基于嵌入式实时操作系统的并发多任务的程序设计方法,采用面向对象技术开发了一种测控软件框架.采用Linux和DSP/BIOS RTOS实施了双操作系统信号处理技术,开发实现了一个面向软性磨粒流的,具有通用多通道高速数据采集功能的智能化嵌入式实时测控平台.研究结果表明,该系统具有易扩展与易交互的优点.

  6. Design of a coil satellite centrifuge and its performance on counter-current chromatographic separation of 4-methylumbelliferyl sugar derivatives with polar organic-aqueous two-phase solvent systems.

    Science.gov (United States)

    Shinomiya, Kazufusa; Tokura, Koji; Kimura, Emiru; Takai, Midori; Harikai, Naoki; Yoshida, Kazunori; Yanagidaira, Kazuhiro; Ito, Yoichiro

    2015-05-01

    A new high-speed counter-current chromatograph, named coil satellite centrifuge (CSC), was designed and fabricated in our laboratory. The CSC apparatus produces the satellite motion such that the coiled column simultaneously rotates around the sun axis (the angular velocity, ω1), the planet axis (ω2) and the satellite axis (the central axis of the column) (ω3). In order to achieve this triplicate rotary motion without twisting of the flow tube, the rotation of each axis was determined by the following formula: ω1=ω2+ω3. This relation enabled to lay out the flow tube without twisting by the simultaneous rotation of three axes. The flow tube was introduced from the bottom side of the apparatus into the sun axis of the first rotary frame reaching the upper side of the planet axis and connected to the column in the satellite axis. The performance of the apparatus was examined on separation of 4-methylumbelliferyl (MU) sugar derivatives as test samples with organic-aqueous two-phase solvent systems composed of ethyl acetate/1-butanol/water (3:2:5, v/v) for lower phase mobile and (1:4:5, v/v) for upper phase mobile. With lower phase mobile, five 4-MU sugar derivatives including β-D-cellobioside (Cel), β-D-glucopyranoside, α-D-mannopyranoside, β-D-fucopyranoside and α-L-fucopyranoside (α-L-Fuc) were separated with the combined rotation around each axis at counterclockwise (CCW) (ω1) - CCW (ω2) - CCW (ω3) by the flow tube distribution. With upper phase mobile, three 4-MU sugar derivatives including α-L-Fuc, β-D-galactopyranoside and Cel were separated with the combined rotation around each axis at clockwise (CW) (ω1) - CW (ω2) - CW (ω3) by the flow tube distribution. A series of experiments on peak resolution and stationary phase retention revealed that better partition efficiencies were obtained at the flow rate of 0.5 mL/min (column 1) and 0.8 mL/min (column 2) for lower phase mobile and 0.2 mL/min (column 1) and 0.4 mL/min (column 2) for upper phase

  7. 离子液体双水相萃取山楂黄酮和多糖的研究%Study on the Extraction of Hawthorn Flavonoids and Polysaccharide in Ionic Liquid Aqueous Two-Phase System

    Institute of Scientific and Technical Information of China (English)

    巩育军; 牛盛童; 黄学锋; 王键

    2014-01-01

    Partition behaviors of hawthorn flavonoids and polysaccharide in ionic liquid aqueous two-phase system(ILATPS)were studied by spectrophotometry.Effects of concentration of ionic liquid and ammonium sulfate,dosage of hawthorn and ultrasonic time on the extraction rate of hawthorn flavonoids and polysaccharide were investigated.The optimal extraction conditions were as follows:concentration of ionic liquid [Bmim]BF4 was 0.26~0.30 g·mL-1,concentration of ammonium sulfate was 0.08~0.10 g·mL-1,dosage of hawthorn was 0.14~0.17 g,ultrasonic time was 15~20 min.Under these conditions,extraction rate of hawthorn fla-vonoids was 86.4%~96.0% in the up phase,and extraction rate of polysaccharide was 75.2%~76.0% in the down phase.%采用分光光度法研究了山楂黄酮和多糖在[Bmim]BF4/(NH4)2 SO4双水相体系的分配行为,探讨了离子液体浓度、(NH4)2 SO4浓度、山楂用量和超声时间等因素对山楂黄酮和多糖萃取率的影响。确定最佳萃取条件为:离子液体[Bmim]BF4浓度0.26~0.30 g·mL-1,(NH4)2 SO4浓度0.08~0.10 g·mL-1,山楂用量0.14~0.17 g,超声时间15~20 min,在此优化条件下,双水相上相中黄酮的萃取率为86.4%~96.0%、下相中多糖的萃取率为75.2%~76.0%。

  8. Two-Phase Quality/Flow Meter

    Science.gov (United States)

    Moerk, J. Steven (Inventor); Youngquist, Robert C. (Inventor); Werlink, Rudy J. (Inventor)

    1999-01-01

    A quality and/or flow meter employs a capacitance probe assembly for measuring the dielectric constant of flow stream, particularly a two-phase flow stream including liquid and gas components.ne dielectric constant of the flow stream varies depending upon the volume ratios of its liquid and gas components, and capacitance measurements can therefore be employed to calculate the quality of the flow, which is defined as the volume ratio of liquid in the flow to the total volume ratio of gas and liquid in the flow. By using two spaced capacitance sensors, and cross-correlating the time varying capacitance values of each, the velocity of the flow stream can also be determined. A microcontroller-based processing circuit is employed to measure the capacitance of the probe sensors.The circuit employs high speed timer and counter circuits to provide a high resolution measurement of the time interval required to charge each capacitor in the probe assembly. In this manner, a high resolution, noise resistant, digital representation of each of capacitance value is obtained without the need for a high resolution A/D converter, or a high frequency oscillator circuit. One embodiment of the probe assembly employs a capacitor with two ground plates which provide symmetry to insure that accurate measurements are made thereby.

  9. Influence of Two-phase Ejector on Performance of Compression/Ejection rRefrigeration System%两相喷射器对压缩-喷射制冷系统性能的影响研究

    Institute of Scientific and Technical Information of China (English)

    魏新利; 汤本凯; 马新灵; 孟祥睿

    2014-01-01

    采用等面积混合模型,以 R134a 制冷剂为工质,对两相喷射器建立热力学模型,并用 Matlab7.1软件进行编程计算,相关的工质热物性参数,通过调用Refprop7软件获取。分析比较了各混合压力下喷射器内压力变化趋势,喷射器混合压力、系统蒸发温度、冷凝温度以及喷射器等熵效率的变化对两相喷射器性能、制冷系统性能的影响。结果表明:对于所研究的工质和工况,热力学分析方法采用等面积混合模型比较合理;混合压力在理论取值范围内存在一个最优点;随蒸发温度的升高或冷凝温度的降低,喷射器最优混合压力的取值点越靠近引射压力,喷射系数增加,系统COP升高,但是相对于传统压缩制冷循环的性能提高率减小;喷射器及系统性能对喷射器进口段等熵效率的变化较敏感。因而,选取恰当的混合压力值,设计制造等熵效率较高的工作喷嘴对于压缩-喷射制冷系统的性能优化至关重要。%This paper establishes a thermodynamic model of two-phase ejector, having the mixing area in the mixing chamber constant and R134a refrigerant as working medium. Matlab7.1 is used in programming and calculating. Thermo-physical properties of the refrigerant involved are obtained through application of Refprop7. Pressure changes in the ejector at various mixing pressures are analyzed. How changes in mixing pressure, evaporation temperature, condensation temperature and isentropic efficiency can influence the performance of the ejector and the refrigeration system is studied. The results show that under the operational conditions in this study, the constant area model for mixing chamber is appropriate for thermodynamic analysis. Within the theoretical value range, there is an optimum value for mixing pressure. As the evaporation temperature increases or the condensation temperature decreases, the optimum mixing pressure comes closer to

  10. 48 CFR 570.105-2 - Two-phase design-build selection procedures.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Two-phase design-build... ADMINISTRATION SPECIAL CONTRACTING PROGRAMS ACQUIRING LEASEHOLD INTERESTS IN REAL PROPERTY General 570.105-2 Two..., you must use the two-phase design-build selection procedures in section 303M of the Federal Property...

  11. A self-referencing biosensor for real-time monitoring of physiological ATP transport in plant systems.

    Science.gov (United States)

    Vanegas, Diana C; Clark, Greg; Cannon, Ashley E; Roux, Stanley; Chaturvedi, Prachee; McLamore, Eric S

    2015-12-15

    The objective of this study was to develop a self-referencing electrochemical biosensor for the direct measurement of ATP flux into the extracellular matrix by living cells/organisms. The working mechanism of the developed biosensor is based on the activity of glycerol kinase and glycerol-3-phosphate oxidase. A stratified bi-enzyme nanocomposite was created using a protein-templated silica sol gel encapsulation technique on top of graphene-modified platinum electrodes. The biosensor exhibited excellent electrochemical performance with a sensitivity of 2.4±1.8 nA/µM, a response time of 20±13 s and a lower detection limit of 1.3±0.7 nM. The self-referencing biosensor was used to measure exogenous ATP efflux by (i) germinating Ceratopteris spores and (ii) growing Zea mays L. roots. This manuscript demonstrates the first development of a non-invasive ATP micro-biosensor for the direct measurement of eATP transport in living tissues. Before this work, assays of eATP have not been able to record the temporally transient movement of ATP at physiological levels (nM and sub-nM). The method demonstrated here accurately measured [eATP] flux in the immediate vicinity of plant cells. Although these proof of concept experiments focus on plant tissues, the technique developed herein is applicable to any living tissue, where nanomolar concentrations of ATP play a critical role in signaling and development. This tool will be invaluable for conducting hypothesis-driven life science research aimed at understanding the role of ATP in the extracellular environment.

  12. Advanced Thermal Protection Systems (ATPS), Aerospace Grade Carbon Bonded Carbon Fiber Material Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Carbon bonded carbon fiber (CBCF) insulating material is the basis for several highly successful NASA developed thermal protection systems (TPS). Included among...

  13. Advanced Thermal Protection Systems (ATPS), Aerospace Grade Carbon Bonded Carbon Fiber Material Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Carbon bonded carbon fiber (CBCF) insulating material is the basis for several highly successful NASA developed thermal protection systems (TPS). Among the...

  14. Vapor Compressor Driven Hybrid Two-Phase Loop Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Small Business Innovation Research Phase I project will demonstrate a vapor compressor driven hybrid two-phase loop technology. The hybrid two-phase loop...

  15. Thermo-fluid dynamics of two-phase flow

    CERN Document Server

    Ishii, Mamoru; Ishii, Mamoru; Ishii, M

    2006-01-01

    Provides a very systematic treatment of two phase flow problems from a theoretical perspectiveProvides an easy to follow treatment of modeling and code devlopemnt of two phase flow related phenomenaCovers new results of two phase flow research such as coverage of fuel cells technology.

  16. Experimental and numerical investigation on two-phase flow instabilities

    Energy Technology Data Exchange (ETDEWEB)

    Ruspini, Leonardo Carlos

    2013-03-01

    Two-phase flow instabilities are experimentally and numerically studied within this thesis. In particular, the phenomena called Ledinegg instability, density wave oscillations and pressure drop oscillations are investigated. The most important investigations regarding the occurrence of two-phase flow instabilities are reviewed. An extensive description of the main contributions in the experimental and analytical research is presented. In addition, a critical discussion and recommendations for future investigations are presented. A numerical framework using a hp-adaptive method is developed in order to solve the conservation equations modelling general thermo-hydraulic systems. A natural convection problem is analysed numerically in order to test the numerical solver. Moreover, the description of an adaptive strategy to solve thermo-hydraulic problems is presented. In the second part of this dissertation, a homogeneous model is used to study Ledinegg, density wave and pressure drop oscillations phenomena numerically. The dynamic characteristics of the Ledinegg (flow excursion) phenomenon are analysed through the simulation of several transient examples. In addition, density wave instabilities in boiling and condensing systems are investigated. The effects of several parameters, such as the fluid inertia and compressibility volumes, on the stability limits of Ledinegg and density wave instabilities are studied, showing a strong influence of these parameters. Moreover, the phenomenon called pressure drop oscillations is numerically investigated. A discussion of the physical representation of several models is presented with reference to the obtained numerical results. Finally, the influence of different parameters on these phenomena is analysed. In the last part, an experimental investigation of these phenomena is presented. The designing methodology used for the construction of the experimental facility is described. Several simulations and a non

  17. AztD, a Periplasmic Zinc Metallochaperone to an ATP-binding Cassette (ABC) Transporter System in Paracoccus denitrificans.

    Science.gov (United States)

    Handali, Melody; Roychowdhury, Hridindu; Neupane, Durga P; Yukl, Erik T

    2015-12-11

    Bacterial ATP-binding cassette (ABC) transporters of transition metals are essential for acquisition of necessary elements from the environment. A large number of Gram-negative bacteria, including human pathogens, have a fourth conserved gene of unknown function adjacent to the canonical permease, ATPase, and solute-binding protein (SBP) genes of the AztABC zinc transporter system. To assess the function of this putative accessory factor (AztD) from Paracoccus denitrificans, we have analyzed its transcriptional regulation, metal binding properties, and interaction with the SBP (AztC). Transcription of the aztD gene is significantly up-regulated under conditions of zinc starvation. Recombinantly expressed AztD purifies with slightly substoichiometric zinc from the periplasm of Escherichia coli and is capable of binding up to three zinc ions with high affinity. Size exclusion chromatography and a simple intrinsic fluorescence assay were used to determine that AztD as isolated is able to transfer bound zinc nearly quantitatively to apo-AztC. Transfer occurs through a direct, associative mechanism that prevents loss of metal to the solvent. These results indicate that AztD is a zinc chaperone to AztC and likely functions to maintain zinc homeostasis through interaction with the AztABC system. This work extends our understanding of periplasmic zinc trafficking and the function of chaperones in this process.

  18. Reynolds transport theorem for a two-phase flow

    Science.gov (United States)

    Collado, Francisco J.

    2007-01-01

    Transport equations for one-dimensional (1d), steady, two-phase flow have been proposed based on the fact that if the phases have different velocities, they cannot cover the same distance (the control volume length) in the same time. Thus, working in the same control volume for the two phases, the time scales of the phases have to be different. From this approach, transport balances for 1D, steady, two-phase flow have been already derived, supplying acceptable correlations for two-phase flow. Here, based on the strict application of the Reynolds transport theorem, general transport balances for two-phase flow are suggested.

  19. Experimental study of two-phase natural circulation circuit

    Energy Technology Data Exchange (ETDEWEB)

    Lemos, Wanderley Freitas; Su, Jian, E-mail: wlemos@lasme.coppe.ufrj.br, E-mail: sujian@nuclear.ufrj.br [Coordenacao dos Programas de Pos-Graduacao em Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear; Faccini, Jose Luiz Horacio, E-mail: faccini@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), RIo de Janeiro, RJ (Brazil). Lab. de Termo-Hidraulica Experimental

    2012-07-01

    This paper reports an experimental study on the behavior of fluid flow in natural circulation under single-and two-phase flow conditions. The natural circulation circuit was designed based on concepts of similarity and scale in proportion to the actual operating conditions of a nuclear reactor. This test equipment has similar performance to the passive system for removal of residual heat presents in Advanced Pressurized Water Reactors (A PWR). The experiment was carried out by supplying water to primary and secondary circuits, as well as electrical power resistors installed inside the heater. Power controller has available to adjust the values for supply of electrical power resistors, in order to simulate conditions of decay of power from the nuclear reactor in steady state. Data acquisition system allows the measurement and control of the temperature at different points by means of thermocouples installed at several points along the circuit. The behavior of the phenomenon of natural circulation was monitored by a software with graphical interface, showing the evolution of temperature measurement points and the results stored in digital format spreadsheets. Besides, the natural circulation flow rate was measured by a flowmeter installed on the hot leg. A flow visualization technique was used the for identifying vertical flow regimes of two-phase natural circulation. Finally, the Reynolds Number was calculated for the establishment of a friction factor correlation dependent on the scale geometrical length, height and diameter of the pipe. (author)

  20. Research on ATP System Technology of Laser Communication Terminal in Space%空间激光通信终端ATP技术与系统研究

    Institute of Scientific and Technical Information of China (English)

    胡贞; 姜会林; 佟首峰; 宋正勋

    2011-01-01

    为了提高某机载空间激光通信终端中捕获、跟踪、对准(ATP)系统的跟踪精度,提出了对该系统的改进方案并研制了样机。对光学接收单元、粗跟踪单元、精跟踪单元以及超前瞄准控制等单元进行了设计。建立了复合轴跟踪系统控制模型,对系统的跟踪控制性能进行了仿真研究。为了验证ATP系统校正粗跟踪残余误差的能力,在激光通信平台振动模拟实验台上进行了模拟实验。结果表明,ATP粗跟踪系统的控制带宽5.5 Hz,精跟踪系统的控制带宽350 Hz,跟踪误差小于2 μrad,ATP系统的跟踪性能得到了提高。%The improved acquisition, tracking, and pointing (ATP) system of the developed airborne laser communication terminal with high precision is presented. The optical antenna, coarse tracking assem-bly, fine tracking assembly, and point-ahead assembly in the ATP system are designed and the prototype is developed. The coarse tracking and the fine pointing control model of the compound-axis system is established and their performance is simulated. In order to further verity the error compensation ability of the ATP system, the experiments to reduce the pointing error are done in the platform vibration simulation system. The results show that if the control frequency bandwidth of the coarse tracking system for the ATP system is about 5. 5 Hz and that of the fine pointing system is about 350 Hz, the pointing error is less than 2 μrad. The performance of the ATP system is improved.

  1. A real two-phase submarine debris flow and tsunami

    Energy Technology Data Exchange (ETDEWEB)

    Pudasaini, Shiva P.; Miller, Stephen A. [Department of Geodynamics and Geophysics, Steinmann Institute, University of Bonn Nussallee 8, D-53115, Bonn (Germany)

    2012-09-26

    The general two-phase debris flow model proposed by Pudasaini is employed to study subaerial and submarine debris flows, and the tsunami generated by the debris impact at lakes and oceans. The model, which includes three fundamentally new and dominant physical aspects such as enhanced viscous stress, virtual mass, and generalized drag (in addition to buoyancy), constitutes the most generalized two-phase flow model to date. The advantage of this two-phase debris flow model over classical single-phase, or quasi-two-phase models, is that the initial mass can be divided into several parts by appropriately considering the solid volume fraction. These parts include a dry (landslide or rock slide), a fluid (water or muddy water; e.g., dams, rivers), and a general debris mixture material as needed in real flow simulations. This innovative formulation provides an opportunity, within a single framework, to simultaneously simulate the sliding debris (or landslide), the water lake or ocean, the debris impact at the lake or ocean, the tsunami generation and propagation, the mixing and separation between the solid and fluid phases, and the sediment transport and deposition process in the bathymetric surface. Applications of this model include (a) sediment transport on hill slopes, river streams, hydraulic channels (e.g., hydropower dams and plants); lakes, fjords, coastal lines, and aquatic ecology; and (b) submarine debris impact and the rupture of fiber optic, submarine cables and pipelines along the ocean floor, and damage to offshore drilling platforms. Numerical simulations reveal that the dynamics of debris impact induced tsunamis in mountain lakes or oceans are fundamentally different than the tsunami generated by pure rock avalanches and landslides. The analysis includes the generation, amplification and propagation of super tsunami waves and run-ups along coastlines, debris slide and deposition at the bottom floor, and debris shock waves. It is observed that the

  2. Extralysosomal turnover of cellular proteins: Targeting substrates in the ubiquitin, ATP-dependent degradation system

    Energy Technology Data Exchange (ETDEWEB)

    Marriott, D.

    1988-01-01

    Calmodulin derived from a cloned chicken gene can be ubiquitinated and degraded by an in vitro reticulocyte lysate system. The chemical reactivity and the surface accessibility of the {epsilon}-amino group on lysine 115 in the calmodulin polypeptide chain were studied by trace labeling with acetic anhydride and with a ubiquitin derivative containing an azido group at the C-terminal glycine residue. Fractionation of reticulocyte lysate proteins separated the activity which degrades the calmodulin moiety of ubiquitin-calmodulin conjugates from that which acts on the isopeptide linkage. Neither of these two activities act on a synthetic isopeptide, which mimics the junction of ubiquitin-calmodulin, indicating the importance of the folding of ubiquitin for recognition. Based on recent findings that the ubiquitin moieties linked to {beta}galactosidase exist as a single multiubiquitin chain, studies were carried out to determine the structure of the ubiquitin-ubiquitin linkage. Ubiquitin was in vivo labeled with ({sup 3}H) and conjugated to {beta}galactosidase. Individual conjugates were isolated and subjected to peptide mapping by trypsin digestion, and tryptic fragments were analyzed of HPLC. The results indicated that the ubiquitin-ubiquitin linkage involves lysine residue 48 in the ubiquitin sequence.

  3. Performance analysis of surge arrester on high voltage systems using ATP

    Energy Technology Data Exchange (ETDEWEB)

    Nallagownden, P.; Magumane, A.H. [Univ. Teknologi Petronas, Perak (Malaysia); Kanth, K.S.R. [Tenaga National Berhad (Malaysia)

    2008-07-01

    Lightning strikes are among the major factors that cause failures in electrical power systems. Phase to ground arresters are commonly installed at power transformer terminals to offer some lightning protection. However, it is important to understand the performance of metal oxide arresters under very fast transient overvoltages in order to determine the protection zone of the arrester and to achieve economical benefits. This study investigated lightning overvoltage protection in a complete three-phase scheme of a 500 KV substation. Overvoltages originated from direct lightning stroke on a phase of a real overhead line (OHL) model. The effect of the separation distance of the arrester from the transformer connected at the open end of the substations was investigated as well as the performance of the arrester for different substation configurations. In the first scenario, the connection of the arrester and transformer was done with a direct connection of an overhead line. In the second scenario, the connection of these devices was done through a cable. Both the overhead line and cable lengths were varied and the maximum overvoltages coming to the transformer were recorded. The results showed that there is a direct proportionality between overvoltages and length of the overhead line or cable. As long the length of the line or cable between the arrester and the transformer was increased, the vulnerability of the transformer to receive high overvoltages also increased. Surge overvoltages were found to be very sensitive to impedance of the line or cable. The direct connections of overhead lines between the arrester and transformer make it necessary to add some protective device. It was suggested that surge arresters should be installed every 200 meters along the overhead lines in order to ensure the safety of equipment. 12 refs., 4 tabs., 8 figs.

  4. Flooding in counter-current two-phase flow

    Energy Technology Data Exchange (ETDEWEB)

    Ragland, W.A.; Ganic, E.N.

    1982-01-01

    Flooding is a phenomenon which is best described as the transition from counter-current to co-current flow. Early notice was taken of this phenomenon in the chemical engineering industry. Flooding also plays an important role in the field of two-phase heat transfer since it is a limit for many systems involving counter-current flow. Practical applications of flooding limited processes include wickless thermosyphons and the emergency core cooling system (ECCS) of pressurized water nuclear reactors. The phenomenon of flooding also is involved in the behavior of nuclear reactor core materials during severe accident conditions where flooding is one of the mechanisms governing the motion of the molten fuel pin cladding.

  5. Design and experiment of household biogas system in alpine region based on two-phase anaerobic fermentation%高寒地区两相厌氧户用沼气系统设计与试验

    Institute of Scientific and Technical Information of China (English)

    孙勇; 李文哲; 张鸿琼

    2012-01-01

    摘要;针对高寒地区农村户用沼气发酵周期过长、产气量少的状况,该文提出并设计了适用于高寒地区农村户用的两相厌氧发酵装置,通过确立合理的工艺方案,控制两相厌氧发酵中产酸相、料液温度和pH值、水力滞留时间等因素,探讨了在哈尔滨地区最寒冷季节,所设计的新型农村户用沼气发酵装置产气量与维持发酵罐体内料液温度所消耗沼气量之间的关系.结果表明:基于两相厌氧发酵的高寒地区高效户用沼气发酵装置最高产气率为1.35m3/(m3·d),是传统沼气池产气率( 0.35 m3/(m3·d))的4倍.冬季1月份日均结余4.08 m3沼气量足以满足三口之家照明、炊事所需能源,实现高寒地区户用沼气全年正能输出,可以取代传统沼气池.该文研究成果为今后寒地户用沼气的发展提供技术支持和参考依据.%According to the problems of long fermentation period and low gas production in the alpine region, a two-phase anaerobic fermentation device was designed for rural household biogas production in the alpine region. The fermentation parameters such as acid production, temperature and pH value of feed and hydraulic retention time were controlled during two-phase anaerobic fermentation. The relationship between the quantity of produced biogas during fermentation and the quantity of consumed biogas to maintain the biogas slurry temperature in most cold season in Harbin was discussed. Results showed that the highest methan production was 1.35 m3/(m3d) using the two-phase anaerobic fermentation process, which was four times higher than the traditional process of 0.35 m3/(m3-d). There was 4.08 m3 daily balance biogas to satisfy lighting and cooking for three people family in January of winter, which could operate in alpine region year-round. In addition, the equipment structure is reasonable and perfect, which might replace the traditional digester. The research can provide a technical support

  6. Efeitos do pH e massa molar do polímero sobre o sistema bifásico aquoso PEG/fosfato = Effects of polymer pH and molar mass on the PEG/phosphate aqueous two-phase system

    Directory of Open Access Journals (Sweden)

    Elias Basile Tambourgi

    2011-07-01

    Full Text Available A extração líquido-líquido usando sistemas bifásicos aquosos (SBA é uma técnica promissora na purificação de biomoléculas de interesse industrial e laboratorial. Este trabalho tem por objetivo apresentar um estudo do diagrama de equilíbrio de fases para diferentes massas molares de polietileno glicol (PEG (400 e 4000 e fosfato de potássio a pHs que variam entre 6 e 11, em condições normais de temperatura e pressão. A influência do peso molecular do PEG em diferentes pHs foram estudados nos diagramas de fases formados. Foram preparadas concentrações de 100 e 50% (p p-1 para o PEG 400 e 4000,respectivamente. A 20% (p p-1 de KH2PO4/K2HPO4, a solução estoque do sal fosfato foi também preparada de forma a obter os pHs desejados (6, 7, 8 e 9. Para os pHs 10 e 11 além dos sais, foi utilizada uma solução de NaOH 1M. Os resultados mostraram que menores concentrações de soluções foram utilizadas para formar o SBA com o PEG de maior massa molar. Por outro lado, não houve influência do pH nas curvas de equilíbrio, ou seja, um deslocamento significativo da binodal em relação aos diferentes pHs.Liquid-liquid extraction using aqueous two-phase systems (ATPSs is a promising technique for the purification of biomolecules of industrial and laboratory interest. This work presents a study of the phase diagrams for different poly(ethylene glycol (PEG molar masses (ranging from 400 to 4000 and potassium phosphate at pH varying from 6 to 11 in standard conditions. The influence of PEG molecular mass at different pHs was studied from the phase diagrams formed. Stocksolutions of PEG 400 and 4000 (100 and 50% w w-1, respectively and phosphate (20% w w-1 KH2PO4/K2HPO4 were prepared at the appropriate pH (6, 7, 8 and 9. For pHs 10 and 11, NaOH 1M was used in addition to the salts. The results showed that low concentrations were used to form the ATPS with high molecular mass PEG. On the other hand, there was no pH influence in the

  7. Aptamer strategy for ATP detection on nanocrystalline diamond functionalized by a nitrogen and hydrogen radical beam system

    Science.gov (United States)

    Suaebah, E.; Seshimo, Y.; Shibata, M.; Kono, S.; Hasegawa, M.; Kawarada, H.

    2017-01-01

    Here, we report a novel method for micropatterning oligonucleotides on the diamond surface via forming amine groups on the diamond surface by nitrogen/hydrogen radical treatment. The covalent bonding of the supporting oligonucleotide and characterization of an immobilized hybridized oligonucleotide with Cy5 modification were investigated by fluorescence microscopy. To investigate the effectiveness of nitrogen/hydrogen radical treatment for amine termination, two types of radical treatment were used: hydrogen/nitrogen radical treatment and pure nitrogen radical treatment. From the results, hydrogen/nitrogen radical treatment produces amine (NH2) termination on the diamond surface. The effect of amine termination was investigated by immobilization of single-stranded DNA via amide bonding between surface NH2 groups and COOH groups terminating the DNA. The immobilized single-stranded DNA (supporting DNA), which has a complementary relationship with the adenosine triphosphate (ATP) aptamer (DNA), hybridizes with the aptamer with attached fluorescence dye. When ATP molecules approach the double-stranded DNA, the aptamer forms a close relationship with the supporting DNA and combines with ATP. ATP detection was effectively carried out by reduction of fluorescence.

  8. Stability of stratified two-phase flows in horizontal channels

    CERN Document Server

    Barmak, Ilya; Ullmann, Amos; Brauner, Neima; Vitoshkin, Helen

    2016-01-01

    Linear stability of stratified two-phase flows in horizontal channels to arbitrary wavenumber disturbances is studied. The problem is reduced to Orr-Sommerfeld equations for the stream function disturbances, defined in each sublayer and coupled via boundary conditions that account also for possible interface deformation and capillary forces. Applying the Chebyshev collocation method, the equations and interface boundary conditions are reduced to the generalized eigenvalue problems solved by standard means of numerical linear algebra for the entire spectrum of eigenvalues and the associated eigenvectors. Some additional conclusions concerning the instability nature are derived from the most unstable perturbation patterns. The results are summarized in the form of stability maps showing the operational conditions at which a stratified-smooth flow pattern is stable. It is found that for gas-liquid and liquid-liquid systems the stratified flow with smooth interface is stable only in confined zone of relatively lo...

  9. Mathematical model of two-phase flow in accelerator channel

    Directory of Open Access Journals (Sweden)

    О.Ф. Нікулін

    2010-01-01

    Full Text Available  The problem of  two-phase flow composed of energy-carrier phase (Newtonian liquid and solid fine-dispersed phase (particles in counter jet mill accelerator channel is considered. The mathematical model bases goes on the supposition that the phases interact with each other like independent substances by means of aerodynamics’ forces in conditions of adiabatic flow. The mathematical model in the form of system of differential equations of order 11 is represented. Derivations of equations by base physical principles for cross-section-averaged quantity are produced. The mathematical model can be used for estimation of any kinematic and thermodynamic flow characteristics for purposely parameters optimization problem solving and transfer functions determination, that take place in  counter jet mill accelerator channel design.

  10. Phase appearance or disappearance in two-phase flows

    CERN Document Server

    Cordier, Floraine; Kumbaro, Anela

    2011-01-01

    This paper is devoted to the treatment of specific numerical problems which appear when phase appearance or disappearance occurs in models of two-phase flows. Such models have crucial importance in many industrial areas such as nuclear power plant safety studies. In this paper, two outstanding problems are identified: first, the loss of hyperbolicity of the system when a phase appears or disappears and second, the lack of positivity of standard shock capturing schemes such as the Roe scheme. After an asymptotic study of the model, this paper proposes accurate and robust numerical methods adapted to the simulation of phase appearance or disappearance. Polynomial solvers are developed to avoid the use of eigenvectors which are needed in usual shock capturing schemes, and a method based on an adaptive numerical diffusion is designed to treat the positivity problems. An alternate method, based on the use of the hyperbolic tangent function instead of a polynomial, is also considered. Numerical results are presente...

  11. Emerging Two-Phase Cooling Technologies for Power Electronic Inverters

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, J.S.

    2005-08-17

    In order to meet the Department of Energy's (DOE's) FreedomCAR and Vehicle Technologies (FVCT) goals for volume, weight, efficiency, reliability, and cost, the cooling of the power electronic devices, traction motors, and generators is critical. Currently the power electronic devices, traction motors, and generators in a hybrid electric vehicle (HEV) are primarily cooled by water-ethylene glycol (WEG) mixture. The cooling fluid operates as a single-phase coolant as the liquid phase of the WEG does not change to its vapor phase during the cooling process. In these single-phase systems, two cooling loops of WEG produce a low temperature (around 70 C) cooling loop for the power electronics and motor/generator, and higher temperature loop (around 105 C) for the internal combustion engine. There is another coolant option currently available in automobiles. It is possible to use the transmission oil as a coolant. The oil temperature exists at approximately 85 C which can be utilized to cool the power electronic and electrical devices. Because heat flux is proportional to the temperature difference between the device's hot surface and the coolant, a device that can tolerate higher temperatures enables the device to be smaller while dissipating the same amount of heat. Presently, new silicon carbide (SiC) devices and high temperature direct current (dc)-link capacitors, such as Teflon capacitors, are available but at significantly higher costs. Higher junction temperature (175 C) silicon (Si) dies are gradually emerging in the market, which will eventually help to lower hardware costs for cooling. The development of high-temperature devices is not the only way to reduce device size. Two-phase cooling that utilizes the vaporization of the liquid to dissipate heat is expected to be a very effective cooling method. Among two-phase cooling methods, different technologies such as spray, jet impingement, pool boiling and submersion, etc. are being developed. The

  12. Equations of two-phase flow in spray chamber

    Institute of Scientific and Technical Information of China (English)

    李新禹; 张志红; 金星; 徐杰

    2009-01-01

    The downstream water-air heat and moisture transfer system in a moving coordinate was studied. The relationship between the diameter of the misted droplets and the spray pressure was determined. Based on the theory of the relative velocity,the two-phase flow mode of the spray chamber and the efficiency equation for heat and moisture exchange were established. Corrections were carried out for the efficiency equation with spray pressure of 157 kPa. The results show that the pressure plays an important part in determining the efficiency of heat and moisture exchange. When the spray pressure is less than 157 kPa,better coincidence is noticed between the theoretical analysis and the test results with the error less than 6%. Greater error will be resulted in the case when the spray pressure is beyond 157 kPa. After the correction treatment,the coincidence between the theoretical and the experimental results is greatly improved.

  13. Thirty-two phase sequences design with good autocorrelation properties

    Indian Academy of Sciences (India)

    S P Singh; K Subba Rao

    2010-02-01

    Polyphase Barker Sequences are finite length, uniform complex sequences; the magnitude of their aperiodic autocorrelation sidelobes are bounded by 1. Such sequences have been used in numerous real-world applications such as channel estimation, radar and spread spectrum communication. In this paper, thirty-two phase Barker sequences up to length 24 with an alphabet size of only 32 are presented. The sequences from length 25 to 289 have autocorrelation properties better than well-known Frank codes. Because of the complex structure the sequences are very difficult to detect and analyse by an enemy’s electronic support measures (ESMs). The synthesized sequences are promising for practical application to radar and spread spectrum communication systems. These sequences are found using the Modified Simulated Annealing Algorithm (MSAA). The convergence rate of the algorithm is good.

  14. Aqueous two-phase (PEG4000/Na2SO4) extraction and characterization of an acid invertase from potato tuber (Solanum tuberosum).

    Science.gov (United States)

    Yuzugullu, Yonca; Duman, Yonca Avcı

    2015-01-01

    Invertases are key metabolic enzymes that catalyze irreversible hydrolysis of sucrose into fructose and glucose. Plant invertases have essential roles in carbohydrate metabolism, plant development, and stress responses. To study their isolation and purification from potato, an attractive system useful for the separation of biological molecules, an aqueous two-phase system, was used. The influence of various system parameters such as type of phase-forming salts, polyethylene glycol (PEG) molecular mass, salt, and polymer concentration was investigated to obtain the highest recovery of enzyme. The PEG4000 (12.5%, w/w)/Na2SO4(15%, w/w) system was found to be ideal for partitioning invertase into the bottom salt-rich phase. The addition of 3% MnSO4 (w/w) at pH 5.0 increased the purity by 5.11-fold with the recovered activity of 197%. The Km and Vmax on sucrose were 3.95 mM and 0.143 U mL(-1) min(-1), respectively. Our data confirmed that the PEG4000/Na2SO4 aqueous two-phase system combined with the presence of MnSO4 offers a low-cost purification of invertase from readily available potato tuber in a single step. The biochemical characteristics of temperature and pH stability for potato invertase prepared from an ATPS make the enzyme a good candidate for its potential use in many research and industrial applications.

  15. Correct numerical simulation of a two-phase coolant

    Science.gov (United States)

    Kroshilin, A. E.; Kroshilin, V. E.

    2016-02-01

    Different models used in calculating flows of a two-phase coolant are analyzed. A system of differential equations describing the flow is presented; the hyperbolicity and stability of stationary solutions of the system is studied. The correctness of the Cauchy problem is considered. The models' ability to describe the following flows is analyzed: stable bubble and gas-droplet flows; stable flow with a level such that the bubble and gas-droplet flows are observed under and above it, respectively; and propagation of a perturbation of the phase concentration for the bubble and gas-droplet media. The solution of the problem about the breakdown of an arbitrary discontinuity has been constructed. Characteristic times of the development of an instability at different parameters of the flow are presented. Conditions at which the instability does not make it possible to perform the calculation are determined. The Riemann invariants for the nonlinear problem under consideration have been constructed. Numerical calculations have been performed for different conditions. The influence of viscosity on the structure of the discontinuity front is studied. Advantages of divergent equations are demonstrated. It is proven that a model used in almost all known investigating thermohydraulic programs, both in Russia and abroad, has significant disadvantages; in particular, it can lead to unstable solutions, which makes it necessary to introduce smoothing mechanisms and a very small step for describing regimes with a level. This does not allow one to use efficient numerical schemes for calculating the flow of two-phase currents. A possible model free from the abovementioned disadvantages is proposed.

  16. Imaging Adenosine Triphosphate (ATP).

    Science.gov (United States)

    Rajendran, Megha; Dane, Eric; Conley, Jason; Tantama, Mathew

    2016-08-01

    Adenosine triphosphate (ATP) is a universal mediator of metabolism and signaling across unicellular and multicellular species. There is a fundamental interdependence between the dynamics of ATP and the physiology that occurs inside and outside the cell. Characterizing and understanding ATP dynamics provide valuable mechanistic insight into processes that range from neurotransmission to the chemotaxis of immune cells. Therefore, we require the methodology to interrogate both temporal and spatial components of ATP dynamics from the subcellular to the organismal levels in live specimens. Over the last several decades, a number of molecular probes that are specific to ATP have been developed. These probes have been combined with imaging approaches, particularly optical microscopy, to enable qualitative and quantitative detection of this critical molecule. In this review, we survey current examples of technologies available for visualizing ATP in living cells, and identify areas where new tools and approaches are needed to expand our capabilities.

  17. Two Phases of Coherent Structure Motions in Turbulent Boundary Layer

    Institute of Scientific and Technical Information of China (English)

    LIU Jian-Hua; JIANG Nan

    2007-01-01

    Two phases of coherent structure motion are acquired after obtaining conditional phase-averaged waveforms for longitudinal velocity of coherent structures in turbulent boundary layer based on Harr wavelet transfer. The correspondences of the two phases to the two processes (i.e. ejection and sweep) during a burst are determined.

  18. Two-phase anaerobic digestion of vegetable market waste fraction of municipal solid waste and development of improved technology for phase separation in two-phase reactor.

    Science.gov (United States)

    Majhi, Bijoy Kumar; Jash, Tushar

    2016-12-01

    Biogas production from vegetable market waste (VMW) fraction of municipal solid waste (MSW) by two-phase anaerobic digestion system should be preferred over the single-stage reactors. This is because VMW undergoes rapid acidification leading to accumulation of volatile fatty acids and consequent low pH resulting in frequent failure of digesters. The weakest part in the two-phase anaerobic reactors was the techniques applied for solid-liquid phase separation of digestate in the first reactor where solubilization, hydrolysis and acidogenesis of solid organic waste occur. In this study, a two-phase reactor which consisted of a solid-phase reactor and a methane reactor was designed, built and operated with VMW fraction of Indian MSW. A robust type filter, which is unique in its implementation method, was developed and incorporated in the solid-phase reactor to separate the process liquid produced in the first reactor. Experiments were carried out to assess the long term performance of the two-phase reactor with respect to biogas production, volatile solids reduction, pH and number of occurrence of clogging in the filtering system or choking in the process liquid transfer line. The system performed well and was operated successfully without the occurrence of clogging or any other disruptions throughout. Biogas production of 0.86-0.889m(3)kg(-1)VS, at OLR of 1.11-1.585kgm(-3)d(-1), were obtained from vegetable market waste, which were higher than the results reported for similar substrates digested in two-phase reactors. The VS reduction was 82-86%. The two-phase anaerobic digestion system was demonstrated to be stable and suitable for the treatment of VMW fraction of MSW for energy generation.

  19. ATP as a peripheral mediator of pain.

    Science.gov (United States)

    Hamilton, S G; McMahon, S B

    2000-07-01

    This article reviews the extent to which recent studies substantiate the hypothesis that ATP functions as a peripheral pain mediator. The discovery of the P2X family of ion channels (for which ATP is a ligand) and, in particular, the highly selective distribution of the P2X(3) receptor within the rat nociceptive system has inspired a variety of approaches to elucidate the potential role of ATP as a pain mediator. ATP elicits excitatory inward currents in small diameter sensory ganglion cells. These currents resemble those elicited by ATP on recombinantly expressed heteromeric P2X(2/3) channels as well as homomultimers consisting of P2X(2) and P2X(3). In vivo behavioural models have characterised the algogenic properties of ATP in normal conditions and in models of peripheral sensitisation. In humans, iontophoresis of ATP induces modest pain. In rats and humans the response is dependent on capsaicin sensitive neurons and is augmented in the presence of inflammatory mediators. Since ATP can be released in the vicinity of peripheral nociceptive terminals under a variety of conditions, there exists a purinergic chain of biological processes linking tissue damage to pain perception. The challenge remains to prove a physiological role for endogenous ATP in activating this chain of events.

  20. Degradation of chloramphenicol in aqueous solution using ozone oxidation in a two-phase system of water/loaded ozone organic solvent%水/载O3有机溶剂两相臭氧氧化法降解水体中氯霉素

    Institute of Scientific and Technical Information of China (English)

    李时银; 史震宇; 陆继来; 邹敏; 张利民

    2011-01-01

    Using a two-phase system of water/perfluorodecalin organic solvent loaded ozone, degradation of chloramphenicol in aqueous solution was conducted. Due to perfluorodecalin has a high ozone stability and solubility, chloramphenicol was used to examine the efficiency of the two-phase ozonation system. During the experiments, effects of initial pH and free radical scavenger on the removal rate of chloramphenicol were investigated respectively. The results showed that the efficiency of two-phase ozonation was increased with the increase of initial pH in water. It was also observed that free radical scavenger had no significant negative effect in two-phase ozonation.%以水/载O3有机溶剂(全氟萘烷)为新型两相臭氧氧化体系,研究了臭氧在全氟萘烷中的溶解度和稳定性,并考察了pH、NaHCO3和叔丁醇对两相体系中臭氧稳定性的影响;以水体中氯霉素为研究对象,考察了初始pH值和自由基抑制剂对两相臭氧氧化体系降解氯霉素效果的影响.结果表明:初始水相pH增大有利于氯霉素的降解;自由基抑制剂对两相体系氧化降解氯霉素影响不显著.

  1. ATP and Presentation Service for Mizar Formalizations

    CERN Document Server

    Urban, Josef; Sitcliffe, Geoff

    2011-01-01

    This paper describes the Automated Reasoning for Mizar (MizAR) service, which integrates several automated reasoning, artificial intelligence, and presentation tools with Mizar and its authoring environment. The service provides ATP assistance to Mizar authors in finding and explaining proofs, and offers generation of Mizar problems as challenges to ATP systems. The service is based on a sound translation from the Mizar language to that of first-order ATP systems, and relies on the recent progress in application of ATP systems in large theories containing tens of thousands of available facts. We present the main features of MizAR services, followed by an account of initial experiments in finding proofs with the ATP assistance. Our initial experience indicates that the tool offers substantial help in exploring the Mizar library and in preparing new Mizar articles.

  2. AtOMA1 Affects the OXPHOS System and Plant Growth in Contrast to Other Newly Identified ATP-Independent Proteases in Arabidopsis Mitochondria.

    Science.gov (United States)

    Migdal, Iwona; Skibior-Blaszczyk, Renata; Heidorn-Czarna, Malgorzata; Kolodziejczak, Marta; Garbiec, Arnold; Janska, Hanna

    2017-01-01

    Compared with yeast, our knowledge on members of the ATP-independent plant mitochondrial proteolytic machinery is rather poor. In the present study, using confocal microscopy and immunoblotting, we proved that homologs of yeast Oma1, Atp23, Imp1, Imp2, and Oct1 proteases are localized in Arabidopsis mitochondria. We characterized these components of the ATP-independent proteolytic system as well as the earlier identified protease, AtICP55, with an emphasis on their significance in plant growth and functionality in the OXPHOS system. A functional complementation assay demonstrated that out of all the analyzed proteases, only AtOMA1 and AtICP55 could substitute for a lack of their yeast counterparts. We did not observe any significant developmental or morphological changes in plants lacking the studied proteases, either under optimal growth conditions or after exposure to stress, with the only exception being retarded root growth in oma1-1, thus implying that the absence of a single mitochondrial ATP-independent protease is not critical for Arabidopsis growth and development. We did not find any evidence indicating a clear functional complementation of the missing protease by any other protease at the transcript or protein level. Studies on the impact of the analyzed proteases on mitochondrial bioenergetic function revealed that out of all the studied mutants, only oma1-1 showed differences in activities and amounts of OXPHOS proteins. Among all the OXPHOS disorders found in oma1-1, the complex V deficiency is distinctive because it is mainly associated with decreased catalytic activity and not correlated with complex abundance, which has been observed in the case of supercomplex I + III2 and complex I deficiencies. Altogether, our study indicates that despite the presence of highly conservative homologs, the mitochondrial ATP-independent proteolytic system is not functionally conserved in plants as compared with yeast. Our findings also highlight the importance of

  3. Rarefaction Waves at the Outlet of the Supersonic Two-Phase Flow Nozzle

    Science.gov (United States)

    Nakagawa, Masafumi; Miyazaki, Hiroki; Harada, Atsushi

    Two-phase flow nozzles are used in the total flow system for geothermal power plants and in the ejector of the refrigerant cycle, etc. One of the most important functions of a two-phase flow nozzle is to convert the thermal energy to the kinetic energy of the two-phase flow. The kinetic energy of the two-phase flow exhausted from a nozzle is available for all applications of this type. There exist the shock waves or rarefaction waves at the outlet of a supersonic nozzle in the case of non-best fitting expansion conditions when the operation conditions of the nozzle are widely chosen. Those waves affect largely on the energy conversion efficiency of the two-phase flow nozzle. The purpose of the present study is to elucidate the character of the rarefaction waves at the outlet of the supersonic two-phase flow nozzle. The high pressure hot water blow down experiment has been carried out. The decompression curves by the rarefaction waves are measured by changing the flow rate of the nozzle and inlet temperature of the hot water. The back pressures of the nozzle are also changed in those experiments. The divergent angles of the two-phase flow flushed out from the nozzle are measured by means of the photograph. The experimental results show that the recompression curves are different from those predicted by the isentropic homogenous two-phase flow. The regions where the rarefaction waves occur become wide due to the increased outlet speed of two-phase flow. The qualitative dependency of this expansion character is the same as the isotropic homogenous flow, but the values obtained from the experiments are quite different. When the back pressure of the nozzle is higher, these regions do not become small in spite of the super sonic two-phase flow. This means that the disturbance of the down-stream propagate to the up-stream. It is shown by the present experiments that the rarefaction waves in the supersonic two-phase flow of water have a subsonic feature. The measured

  4. Expansion Waves at the Outlet of the Supersonic Two-Phase Flow Nozzle

    Science.gov (United States)

    Nakagawa, Masafumi; Miyazaki, Hiroki; Harada, Atsushi; Ibragimov, Zokirjon

    Two-phase flow nozzles are used in the total flow system of geothermal power plants and in the ejector of the refrigeration cycle, etc. One of the most important functions of the two-phase flow nozzle is converting two-phase flow thermal energy into kinetic energy. The kinetic energy of the two-phase flow exhausted from a nozzle is available for all applications of this type. In the case of non-best fitting expansion conditions, when the operation conditions of the supersonic nozzle are widely chosen, there exist shock waves or expansion waves at the outlet of the nozzle. Those waves affect largely the energy conversion efficiency of the two-phase flow nozzle. The purpose of the present study is to elucidate character of the expansion waves at the outlet of the supersonic two-phase flow nozzle. High-pressure hot water blowdown experiments have been carried out. The decompression curves of the expansion waves are measured by changing the flowrate in the nozzle and inlet temperature of the hot water. The back pressures of the nozzle are also changed in those experiments. The expansion angles of the two-phase flow flushed out from the nozzle are measured by means of the photograph. The experimental results show that the decompression curves are different from those predicted by the isentropic homogeneous two-phase flow theory. The regions where the expansion waves occur become wide due to the increased outlet speed of the two-phase flow. The qualitative dependency of this expansion character is the same as the isentropic homogeneous flow, but the values obtained from the experiments are quite different. When the back pressure of the nozzle is higher, these regions do not become small in spite of the supersonic two-phase flow. This means that the disturbance in the downstream propagates to the upstream. It is shown by the present experiments that the expansion waves in the supersonic two-phase flow of water have a subsonic feature. The measured expansion angles become

  5. New results in gravity dependent two-phase flow regime mapping

    Science.gov (United States)

    Kurwitz, Cable; Best, Frederick

    2002-01-01

    Accurate prediction of thermal-hydraulic parameters, such as the spatial gas/liquid orientation or flow regime, is required for implementation of two-phase systems. Although many flow regime transition models exist, accurate determination of both annular and slug regime boundaries is not well defined especially at lower flow rates. Furthermore, models typically indicate the regime as a sharp transition where data may indicate a transition space. Texas A&M has flown in excess of 35 flights aboard the NASA KC-135 aircraft with a unique two-phase package. These flights have produced a significant database of gravity dependent two-phase data including visual observations for flow regime identification. Two-phase flow tests conducted during recent zero-g flights have added to the flow regime database and are shown in this paper with comparisons to selected transition models. .

  6. Research of Characteristics of Gas-liquid Two-phase Pressure Drop in Microreactor

    Directory of Open Access Journals (Sweden)

    Li Dan

    2015-01-01

    Full Text Available With the research system of nitrogen and deionized water, this paper researches the pressure drop of gas-liquid two-phase flow in the circular microchannel with an inner diameter which is respectively 0.9mm and 0.5mm, analyzes the effect of microchannel diameter on gas-liquid two-phase frictional pressure drop in the microchannel reactor, and compares with the result of frictional pressure drop and the predicting result of divided-phase flow pattern. The result shows that, the gas-liquid two-phase frictional pressure drop in the microchannel significantly increases with the decreasing microchannel diameter; Lockhart-Martinelli relationship in divided-phase flow pattern can preferably predict the gas-liquid two-phase frictional pressure drop in the microchannel, but the Tabular constant needs to be corrected.

  7. Experimental study on transient behavior of semi-open two-phase thermosyphon

    Institute of Scientific and Technical Information of China (English)

    朱华; 王建新; 张巧惠; 屠传经

    2004-01-01

    An experimental system was set up to measure the temperature, pressure, heat transfer rate and mass flow rate in a semi-open two-phase thermosyphon. The behaviors of a semi-open two-phase thermosyphon during startup, shutdown and lack of water were studied to get complete understanding of its thermal characteristics. The variation of wall temperature, heat-exchange condition and pressure fluctuations of semi-open two-phase thermosyphons showed that the startup of SOTPT needs about 60-70 min; the startup speed of SOTPT is determined by the startup speed of the condensation section; the average pressure in the heat pipe is equal to the environmental pressure usually; the shutdown of SOTPT needs about 30-50min; a semi-open two-phase thermosyphon has good response to lack of water accident.

  8. A Rotational Pressure-Correction Scheme for Incompressible Two-Phase Flows with Open Boundaries.

    Science.gov (United States)

    Dong, S; Wang, X

    2016-01-01

    Two-phase outflows refer to situations where the interface formed between two immiscible incompressible fluids passes through open portions of the domain boundary. We present several new forms of open boundary conditions for two-phase outflow simulations within the phase field framework, as well as a rotational pressure correction based algorithm for numerically treating these open boundary conditions. Our algorithm gives rise to linear algebraic systems for the velocity and the pressure that involve only constant and time-independent coefficient matrices after discretization, despite the variable density and variable viscosity of the two-phase mixture. By comparing simulation results with theory and the experimental data, we show that the method produces physically accurate results. We also present numerical experiments to demonstrate the long-term stability of the method in situations where large density contrast, large viscosity contrast, and backflows occur at the two-phase open boundaries.

  9. What types of investors generate the two-phase phenomenon?

    Science.gov (United States)

    Ryu, Doojin

    2013-12-01

    We examine the two-phase phenomenon described by Plerou, Gopikrishnan, and Stanley (2003) [1] in the KOSPI 200 options market, one of the most liquid options markets in the world. By analysing a unique intraday dataset that contains information about investor type for each trade and quote, we find that the two-phase phenomenon is generated primarily by domestic individual investors, who are generally considered to be uninformed and noisy traders. In contrast, our empirical results indicate that trades by foreign institutions, who are generally considered informed and sophisticated investors, do not exhibit two-phase behaviour.

  10. Tunable two-phase coexistence in half-doped manganites

    Indian Academy of Sciences (India)

    P Chaddah; A Banerjee

    2008-02-01

    We discuss our very interesting experimental observation that the low-temperature two-phase coexistence in half-doped manganites is multi-valued (at any field) in that we can tune the coexisting antiferromagnetic-insulating (AF-I) and the ferromagnetic-metallic (FM-M) phase fractions by following different paths in (; ) space. We have shown experimentally that the phase fraction, in this two-phase coexistence, can take continuous infinity of values. All but one of these are metastable, and two-phase coexistence is not an equilibrium state.

  11. Passive Two-Phase Cooling of Automotive Power Electronics: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Moreno, G.; Jeffers, J. R.; Narumanchi, S.; Bennion, K.

    2014-08-01

    Experiments were conducted to evaluate the use of a passive two-phase cooling strategy as a means of cooling automotive power electronics. The proposed cooling approach utilizes an indirect cooling configuration to alleviate some reliability concerns and to allow the use of conventional power modules. An inverter-scale proof-of-concept cooling system was fabricated, and tests were conducted using the refrigerants hydrofluoroolefin HFO-1234yf and hydrofluorocarbon HFC-245fa. Results demonstrated that the system can dissipate at least 3.5 kW of heat with 250 cm3 of HFC-245fa. An advanced evaporator design that incorporates features to improve performance and reduce size was conceived. Simulation results indicate its thermal resistance can be 37% to 48% lower than automotive dual side cooled power modules. Tests were also conducted to measure the thermal performance of two air-cooled condensers--plain and rifled finned tube designs. The results combined with some analysis were then used to estimate the required condenser size per operating conditions and maximum allowable system (i.e., vapor and liquid) temperatures.

  12. Time dependent two phase flows in Magnetohydrodynamics: A ...

    African Journals Online (AJOL)

    Journal of the Nigerian Association of Mathematical Physics ... Open Access DOWNLOAD FULL TEXT Subscription or Fee Access. Time dependent two phase flows in Magnetohydrodynamics: A Greens function approach. BK Jha, HM Jibril ...

  13. Gravity Independence of Microchannel Two-Phase Flow Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Most of the amassed two-phase flow and heat transfer knowledge comes from experiments conducted in Earth’s gravity. Space missions span varying gravity levels,...

  14. Vapor Compressor Driven Hybrid Two-Phase Loop Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Phase I project successfully demonstrated the feasibility of the vapor compression hybrid two-phase loop (VCHTPL). The test results showed the high...

  15. Particle modulations to turbulence in two-phase round jets

    Institute of Scientific and Technical Information of China (English)

    Bing Wang; Huiqiang Zhang; Yi Liu; Xiaofen Yan; Xilin Wang

    2009-01-01

    The particle modulations to turbulence in round jets were experimentally studied by means of two-phase velocity measurements with Phase Doppler Anemometer (PDA). Laden with very large particles, no significant attenuations of turbulence intensities were measured in the far-fields, due to small two-phase slip velocities and particle Reynolds number. The gas-phase turbulence is enhanced by particles in the near-fields, but it is significantly attenuated by the small particles in the far-fields. The smaller particles have a more profound effect on the attenuation of turbulence intensities. The enhancements or attenuations of turbulence intensities in the far-fields depends on the energy production, transport and dissipation mechanisms between the two phases, which are determined by the particle prop-erties and two-phase velocity slips. The non-dimensional parameter CTI is introduced to represent the change of turbulence intensity.

  16. Transient two-phase performance of LOFT reactor coolant pumps

    Energy Technology Data Exchange (ETDEWEB)

    Chen, T.H.; Modro, S.M.

    1983-01-01

    Performance characteristics of Loss-of-Fluid Test (LOFT) reactor coolant pumps under transient two-phase flow conditions were obtained based on the analysis of two large and small break loss-of-coolant experiments conducted at the LOFT facility. Emphasis is placed on the evaluation of the transient two-phase flow effects on the LOFT reactor coolant pump performance during the first quadrant operation. The measured pump characteristics are presented as functions of pump void fraction which was determined based on the measured density. The calculated pump characteristics such as pump head, torque (or hydraulic torque), and efficiency are also determined as functions of pump void fractions. The importance of accurate modeling of the reactor coolant pump performance under two-phase conditions is addressed. The analytical pump model, currently used in most reactor analysis codes to predict transient two-phase pump behavior, is assessed.

  17. IMPROVED SUBGRID SCALE MODEL FOR DENSE TURBULENT SOLID-LIQUID TWO-PHASE FLOWS

    Institute of Scientific and Technical Information of China (English)

    TANG Xuelin; QIAN Zhongdong; WU Yulin

    2004-01-01

    The dense solid-phase governing equations for two-phase flows are obtained by using the kinetic theory of gas molecules. Assuming that the solid-phase velocity distributions obey the Maxwell equations, the collision term for particles under dense two-phase flow conditions is also derived.In comparison with the governing equations of a dilute two-phase flow, the solid-particle's governing equations are developed for a dense turbulent solid-liquid flow by adopting some relevant terms from the dilute two-phase governing equations. Based on Cauchy-Helmholtz theorem and Smagorinsky model,a second-order dynamic sub-grid-scale (SGS) model, in which the sub-grid-scale stress is a function of both the strain-rate tensor and the rotation-rate tensor, is proposed to model the two-phase governing equations by applying dimension analyses. Applying the SIMPLEC algorithm and staggering grid system to the two-phase discretized governing equations and employing the slip boundary conditions on the walls, the velocity and pressure fields, and the volumetric concentration are calculated. The simulation results are in a fairly good agreement with experimental data in two operating cases in a conduit with a rectangular cross-section and these comparisons imply that these models are practical.

  18. Mixed Model for Silt-Laden Solid-Liquid Two-Phase Flows

    Institute of Scientific and Technical Information of China (English)

    唐学林; 徐宇; 吴玉林

    2003-01-01

    The kinetic theory of molecular gases was used to derive the governing equations for dense solid-liquid two-phase flows from a microscopic flow characteristics viewpoint by multiplying the Boltzmann equation for each phase by property parameters and integrating over the velocity space. The particle collision term was derived from microscopic terms by comparison with dilute two-phase flow but with consideration of the collisions between particles for dense two-phase flow conditions and by assuming that the particle-phase velocity distribution obeys the Maxwell equations. Appropriate terms from the dilute two-phase governing equations were combined with the dense particle collision term to develop the governing equations for dense solid-liquid turbulent flows. The SIMPLEC algorithm and a staggered grid system were used to solve the discretized two-phase governing equations with a Reynolds averaged turbulence model. Dense solid-liquid turbulent two-phase flows were simulated for flow in a duct. The simulation results agree well with experimental data.

  19. Unsteady flow analysis of a two-phase hydraulic coupling

    Science.gov (United States)

    Hur, N.; Kwak, M.; Lee, W. J.; Moshfeghi, M.; Chang, C.-S.; Kang, N.-W.

    2016-06-01

    Hydraulic couplings are being widely used for torque transmitting between separate shafts. A mechanism for controlling the transmitted torque of a hydraulic system is to change the amount of working fluid inside the system. This paper numerically investigates three-dimensional turbulent flow in a real hydraulic coupling with different ratios of charged working fluid. Working fluid is assumed to be water and the Realizable k-ɛ turbulence model together with the VOF method are used to investigate two-phase flow inside the wheels. Unsteady simulations are conducted using the sliding mesh technique. The primary wheel is rotating at a fixed speed of 1780 rpm and the secondary wheel rotates at different speeds for simulating different speed ratios. Results are investigated for different blade angles, speed ratios and also different water volume fractions, and are presented in the form of flow patterns, fluid average velocity and also torques values. According to the results, blade angle severely affects the velocity vector and the transmitted torque. Also in the partially-filled cases, air is accumulated in the center of the wheel forming a toroidal shape wrapped by water and the transmitted torque sensitively depends on the water volume fraction. In addition, in the fully-filled case the transmitted torque decreases as the speed ration increases and the average velocity associated with lower speed ratios are higher.

  20. Creep of Two-Phase Microstructures for Microelectronic Applications

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, Heidi Linch [Univ. of California, Berkeley, CA (United States)

    1998-12-01

    The mechanical properties of low-melting temperature alloys are highly influenced by their creep behavior. This study investigates the dominant mechanisms that control creep behavior of two-phase, low-melting temperature alloys as a function of microstructure. The alloy systems selected for study were In-Ag and Sn-Bi because their eutectic compositions represent distinctly different microstructure.” The In-Ag eutectic contains a discontinuous phase while the Sn-Bi eutectic consists of two continuous phases. In addition, this work generates useful engineering data on Pb-free alloys with a joint specimen geometry that simulates microstructure found in microelectronic applications. The use of joint test specimens allows for observations regarding the practical attainability of superplastic microstructure in real solder joints by varying the cooling rate. Steady-state creep properties of In-Ag eutectic, Sn-Bi eutectic, Sn-xBi solid-solution and pure Bi joints have been measured using constant load tests at temperatures ranging from O°C to 90°C. Constitutive equations are derived to describe the steady-state creep behavior for In-Ageutectic solder joints and Sn-xBi solid-solution joints. The data are well represented by an equation of the form proposed by Dom: a power-law equation applies to each independent creep mechanism. Rate-controlling creep mechanisms, as a function of applied shear stress, test temperature, and joint microstructure, are discussed. Literature data on the steady-state creep properties of Sn-Bi eutectic are reviewed and compared with the Sn-xBi solid-solution and pure Bi joint data measured in the current study. The role of constituent phases in controlling eutectic creep behavior is discussed for both alloy systems. In general, for continuous, two-phase microstructure, where each phase exhibits significantly different creep behavior, the harder or more creep resistant phase will dominate the creep behavior in a lamellar microstructure. If a

  1. Supramolecular Complexes Formed by the Self-assembly of Hydrophobic Bis(Zn(2+)-cyclen) Complexes, Copper, and Di- or Triimide Units for the Hydrolysis of Phosphate Mono- and Diesters in Two-Phase Solvent Systems (Cyclen=1,4,7,10-Tetraazacyclododecane).

    Science.gov (United States)

    Hisamatsu, Yosuke; Miyazawa, Yuya; Yoneda, Kakeru; Miyauchi, Miki; Zulkefeli, Mohd; Aoki, Shin

    2016-01-01

    We previously reported on supramolecular complexes 4 and 5, formed by the 4 : 4 : 4 or 2 : 2 : 2 assembly of a dimeric zinc(II) complex (Zn2L(1)) having 2,2'-bipyridyl linker, dianion of cyanuric acid (CA) or 5,5-diethylbarbituric acid (Bar), and copper(II) ion (Cu(2+)) in an aqueous solution. The supermolecule 4 possesses Cu2(μ-OH)2 centers and catalyzes hydrolysis of phosphate monoester dianion, mono(4-nitrophenyl)phosphate (MNP), at neutral pH. In this manuscript, we report on design and synthesis of hydrophobic supermolecules 9 and 10 by 4 : 4 : 4 and 2 : 2 : 2 self-assembly of hydrophobic Zn2L(2) and Zn2L(3) containing long alkyl chains, CA or Bar, and Cu(2+) and their phosphatase activity for the hydrolysis of MNP and bis(4-nitrophenyl)phosphate (BNP) in two-phase solvent systems. We assumed that the Cu2(μ-OH)2 active sites of 9 and 10 would be more stable in organic solvent than in aqueous solution and that product inhibition of the supermolecules might be avoided by the release of HPO4(2-) into the aqueous layer. The findings indicate that 9 and 10 exhibit phosphatase activity in the two-phase solvent system, although catalytic turnover was not observed. Furthermore, the hydrolysis of BNP catalyzed by the hydrophobic 2 : 2 : 2 supermolecules in the two-phase solvent system is described.

  2. Dynamic behavior of pipes conveying gas–liquid two-phase flow

    Energy Technology Data Exchange (ETDEWEB)

    An, Chen, E-mail: anchen@cup.edu.cn [Offshore Oil/Gas Research Center, China University of Petroleum-Beijing, Beijing 102249 (China); Su, Jian, E-mail: sujian@lasme.coppe.ufrj.br [Nuclear Engineering Program, COPPE, Universidade Federal do Rio de Janeiro, CP 68509, Rio de Janeiro 21941-972 (Brazil)

    2015-10-15

    Highlights: • Dynamic behavior of pipes conveying gas–liquid two-phase flow was analyzed. • The generalized integral transform technique (GITT) was applied. • Excellent convergence behavior and long-time stability were shown. • Effects of volumetric quality and volumetric flow rate on dynamic behavior were studied. • Normalized volumetric-flow-rate stability envelope of dynamic system was determined. - Abstract: In this paper, the dynamic behavior of pipes conveying gas–liquid two-phase flow was analytically and numerically investigated on the basis of the generalized integral transform technique (GITT). The use of the GITT approach in the analysis of the transverse vibration equation lead to a coupled system of second order differential equations in the dimensionless temporal variable. The Mathematica's built-in function, NDSolve, was employed to numerically solve the resulting transformed ODE system. The characteristics of gas–liquid two-phase flow were represented by a slip-ratio factor model that was devised and used for similar problems. Good convergence behavior of the proposed eigenfunction expansions is demonstrated for calculating the transverse displacement at various points of pipes conveying air–water two-phase flow. Parametric studies were performed to analyze the effects of the volumetric gas fraction and the volumetric flow rate on the dynamic behavior of pipes conveying air–water two-phase flow. Besides, the normalized volumetric-flow-rate stability envelope for the dynamic system was obtained.

  3. Statistical descriptions of polydisperse turbulent two-phase flows

    Science.gov (United States)

    Minier, Jean-Pierre

    2016-12-01

    Disperse two-phase flows are flows containing two non-miscible phases where one phase is present as a set of discrete elements dispersed in the second one. These discrete elements, or 'particles', can be droplets, bubbles or solid particles having different sizes. This situation encompasses a wide range of phenomena, from nano-particles and colloids sensitive to the molecular fluctuations of the carrier fluid to inertia particles transported by the large-scale motions of turbulent flows and, depending on the phenomenon studied, a broad spectrum of approaches have been developed. The aim of the present article is to analyze statistical models of particles in turbulent flows by addressing this issue as the extension of the classical formulations operating at a molecular or meso-molecular level of description. It has a three-fold purpose: (1) to bring out the thread of continuity between models for discrete particles in turbulent flows (above the hydrodynamical level of description) and classical mesoscopic formulations of statistical physics (below the hydrodynamical level); (2) to reveal the specific challenges met by statistical models in turbulence; (3) to establish a methodology for modeling particle dynamics in random media with non-zero space and time correlations. The presentation is therefore centered on organizing the different approaches, establishing links and clarifying physical foundations. The analysis of disperse two-phase flow models is developed by discussing: first, approaches of classical statistical physics; then, by considering models for single-phase turbulent flows; and, finally, by addressing current formulations for discrete particles in turbulent flows. This brings out that particle-based models do not cease to exist above the hydrodynamical level and offer great interest when combined with proper stochastic formulations to account for the lack of equilibrium distributions and scale separation. In the course of this study, general results

  4. The Effect of Cigarette Smoking on Human Sperm Creatine Kinase Activity: As An ATP Buffering System in Sperm

    Directory of Open Access Journals (Sweden)

    Mohammad Ali Ghaffari

    2013-01-01

    Full Text Available Background: Spermatozoa are a group of cells that consume adenosine triphosphate (ATP rapidly.Creatine kinase (CK, produced by creatine phosphate, is an energy reservoir for the rapid bufferingand regeneration of ATP and can play an important role in sperm motility. Therefore, this studyinvestigates the effects of cigarette smoking on human sperm CK activity in males who smoke.Materials and Methods: In this case - control study, we obtained semen samples from male smokers(n=64 and nonsmokers (n=83. Smokers were categorized as light, moderate, or heavy smokersaccording to the daily number of cigarettes smoked and the number of years they have smoked. Datawere analyzed by the independent t test and Pearson’s analysis.Results: This investigation showed significantly lower sperm CK activity and movement in malesmokers compared to nonsmokers. In addition, it was demonstrated that cigarette smoking had adose-dependent effect on these parameters. There was a positive relation, although not significant,between sperm CK activity and its motility in male smokers.Conclusion: Smoking, by diminishing sperm CK activity, may potentially impair sperm energyhomeostasis and have an association with damage to sperm motility. This effect can be an importantmechanism that may cause infertility in male smokers. However, further research is necessary toelucidate the underlying mechanism of sperm motility damage caused by cigarette smoking.

  5. Stability of stratified two-phase flows in horizontal channels

    Science.gov (United States)

    Barmak, I.; Gelfgat, A.; Vitoshkin, H.; Ullmann, A.; Brauner, N.

    2016-04-01

    Linear stability of stratified two-phase flows in horizontal channels to arbitrary wavenumber disturbances is studied. The problem is reduced to Orr-Sommerfeld equations for the stream function disturbances, defined in each sublayer and coupled via boundary conditions that account also for possible interface deformation and capillary forces. Applying the Chebyshev collocation method, the equations and interface boundary conditions are reduced to the generalized eigenvalue problems solved by standard means of numerical linear algebra for the entire spectrum of eigenvalues and the associated eigenvectors. Some additional conclusions concerning the instability nature are derived from the most unstable perturbation patterns. The results are summarized in the form of stability maps showing the operational conditions at which a stratified-smooth flow pattern is stable. It is found that for gas-liquid and liquid-liquid systems, the stratified flow with a smooth interface is stable only in confined zone of relatively low flow rates, which is in agreement with experiments, but is not predicted by long-wave analysis. Depending on the flow conditions, the critical perturbations can originate mainly at the interface (so-called "interfacial modes of instability") or in the bulk of one of the phases (i.e., "shear modes"). The present analysis revealed that there is no definite correlation between the type of instability and the perturbation wavelength.

  6. Microporous silica gels from alkylsilicate-water two phase hydrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Chu, L.; Tejedor-Tejedor, M.I.; Anderson, M.A. [Univ. of Wisconsin, Madison, WI (United States). Water Chemistry Program

    1994-12-31

    Microporous silica gels have been synthesized through a nano-particulate sol-gel route. These gels have uniformly distributed and extremely small pores(< 15 {angstrom} in diameter). Hydrolysis and condensation reactions leading to these gels were carried out in an alkyl silicate-water (ammonia) two phase system. These reactions took place at the alkyl silicate droplet-water interfacial boundary. No alcohol was added. A clear, stable and uniformly distributed colloidal silica suspension having an average particle size less than 6 nm was prepared by this method. Fast hydrolysis, slow condensation and low solubility all contribute to a high supersaturation level and result in the formation of small particles. This process is consistent with classic nucleation theory. When the particles are produced under acidic rather than under basic reaction conditions, smaller particles are formed due to the slower condensation rate and lower solubility of these silica particles in acidic conditions. At the same pH, alkylsilicates having smaller alkyl groups react faster with water leading to smaller primary particles. Homogeneous nucleation conditions are achieved when the water/alkylsilicate ratio is high.

  7. Pressure transient analysis of two-phase flow problems

    Energy Technology Data Exchange (ETDEWEB)

    Chu, W.C.; Reynolds, A.C.; Raghavan, R.

    1986-04-01

    This paper considers the analysis of pressure drawdown and buildup data for two-phase flow problems. Of primary concern is the analysis of data influenced by saturation gradients that exist within the reservoir. Wellbore storage effects are assumed to be negligible. The pressure data considered are obtained from a two-dimensional (2D) numerical coning model for an oil/water system. The authors consider constant-rate production followed by a buildup period and assume that the top, bottom, and outer boundaries of the reservoir are sealed. First, they consider the case where the producing interval is equal to the total formation thickness. Second, they discuss the effect of partial penetration. In both cases, they show that average pressure can be estimated by the Matthews-Brons-Hazebroek method and consider the computation of the skin factor. They also show that a reservoir limit test can estimate reservoir PV only if the total mobility adjacent to the wellbore does not vary with time.

  8. STUDIES OF TWO-PHASE PLUMES IN STRATIFIED ENVIRONMENTS

    Energy Technology Data Exchange (ETDEWEB)

    Scott A. Socolofsky; Brian C. Crounse; E. Eric Adams

    1998-11-18

    Two-phase plumes play an important role in the more practical scenarios for ocean sequestration of CO{sub 2}--i.e. dispersing CO{sub 2} as a buoyant liquid from either a bottom-mounted or ship-towed pipeline. Despite much research on related applications, such as for reservoir destratification using bubble plumes, our understanding of these flows is incomplete, especially concerning the phenomenon of plume peeling in a stratified ambient. To address this deficiency, we have built a laboratory facility in which we can make fundamental measurements of plume behavior. Although we are using air, oil and sediments as our sources of buoyancy (rather than CO{sub 2}), by using models, our results can be directly applied to field scale CO{sub 2} releases to help us design better CO{sub 2} injection systems, as well as plan and interpret the results of our up-coming international field experiment. The experimental facility designed to study two-phase plume behavior similar to that of an ocean CO{sub 2} release includes the following components: 1.22 x 1.22 x 2.44 m tall glass walled tank; Tanks and piping for the two-tank stratification method for producing step- and linearly-stratified ambient conditions; Density profiling system using a conductivity and temperature probe mounted to an automated depth profiler; Lighting systems, including a virtual point source light for shadowgraphs and a 6 W argon-ion laser for laser induced fluorescence (LIF) imaging; Imaging system, including a digital, progressive scanning CCD camera, computerized framegrabber, and image acquisition and analysis software; Buoyancy source diffusers having four different air diffusers, two oil diffusers, and a planned sediment diffuser; Dye injection method using a Mariotte bottle and a collar diffuser; and Systems integration software using the Labview graphical programming language and Windows NT. In comparison with previously reported experiments, this system allows us to extend the parameter range of

  9. Performance of a passive emergency heat removal system of advanced reactors in two-phase flow and with high concentration of non-condensable; Atuacao de um sistema passivo de remocao de calor de emergencia de reatores avancados em escoamento bifasico e com alta concentracao de nao-condensaveis

    Energy Technology Data Exchange (ETDEWEB)

    Macedo, Luiz Alberto

    2008-07-01

    The research and the development of passive emergency cooling systems are necessary for the new generation of thermo-nuclear systems. Some basic information on the operation of these systems require the research of some relative processes to the natural circulation, mainly in conditions of two-phase flow involving processes of condensation in the presence of non-condensable gases, because many found situations are new. The experimental facility called Bancada de Circulacao Natural (BCN) was used for the realization of tests with diverse concentrations of non-condensable and power levels. The non-condensable gas present in the circuit decreases the rate of heat transfer for the secondary of the heat exchanger, determining low efficiency of the heat exchanger. High concentration of non-condensable in the vapor condensation, determines negative pressure, and cause the inversion of the flow in the circuit. The initial concentration of non-condensable and the geometry of the circuit, in the inlet of the heat exchanger, determines the establishment of transitory with two-phase flow. The BCN was performed with the computational code of Analysis of Accidents and Thermal-Hydraulics RELAP5/MOD 3.3 and, the calculated values had been compared with the experimental data, presenting good agreement for small non-condensable concentrations. The values calculated for high concentrations of non-condensable had been satisfactory after the circuit to have reached the temperature of saturation in the electric heater. (author)

  10. Integrated method of thermosensitive triblock copolymer-salt aqueous two phase extraction and dialysis membrane separation for purification of lycium barbarum polysaccharide.

    Science.gov (United States)

    Wang, Yun; Hu, Xiaowei; Han, Juan; Ni, Liang; Tang, Xu; Hu, Yutao; Chen, Tong

    2016-03-01

    A polymer-salt aqueous two-phase system (ATPS) consisting of thermosensitive copolymer ethylene-oxide-b-propylene-oxide-b-ethylene-oxide (EOPOEO) and NaH2PO4 was employed in deproteinization for lycium barbarum polysaccharide (LBP). The effects of salt type and concentration, EOPOEO concentration, amount of crude LBP solution and temperature were studied. In the primary extraction process, LBP was preferentially partitioned to the bottom (salt-rich) phase with high recovery ratio of 96.3%, while 94.4% of impurity protein was removed to the top (EOPOEO-rich) phase. Moreover, the majority of pigments could be discarded to top phase. After phase-separation, the LBP in the bottom phase was further purified by dialysis membrane to remove salt and other small molecular impurities. The purity of LBP was enhanced to 64%. Additionally, the FT-IR spectrum was used to identify LBP. EOPOEO was recovered by a temperature-induced separation, and reused in a new ATPS. An ideal extraction and recycle result were achieved.

  11. Thermodynamics of proton transport coupled ATP synthesis.

    Science.gov (United States)

    Turina, Paola; Petersen, Jan; Gräber, Peter

    2016-06-01

    The thermodynamic H(+)/ATP ratio of the H(+)-ATP synthase from chloroplasts was measured in proteoliposomes after energization of the membrane by an acid base transition (Turina et al. 2003 [13], 418-422). The method is discussed, and all published data obtained with this system are combined and analyzed as a single dataset. This meta-analysis led to the following results. 1) At equilibrium, the transmembrane ΔpH is energetically equivalent to the transmembrane electric potential difference. 2) The standard free energy for ATP synthesis (reference reaction) is ΔG°(ref)=33.8±1.3kJ/mol. 3) The thermodynamic H(+)/ATP ratio, as obtained from the shift of the ATP synthesis equilibrium induced by changing the transmembrane ΔpH (varying either pH(in) or pH(out)) is 4.0±0.1. The structural H(+)/ATP ratio, calculated from the ratio of proton binding sites on the c-subunit-ring in F(0) to the catalytic nucleotide binding sites on the β-subunits in F(1), is c/β=14/3=4.7. We infer that the energy of 0.7 protons per ATP that flow through the enzyme, but do not contribute to shifting the ATP/(ADP·Pi) ratio, is used for additional processes within the enzyme, such as activation, and/or energy dissipation, due e.g. to internal uncoupling. The ratio between the thermodynamic and the structural H(+)/ATP values is 0.85, and we conclude that this value represents the efficiency of the chemiosmotic energy conversion within the chloroplast H(+)-ATP synthase.

  12. The Role of ATP in the Regulation of NCAM Function

    DEFF Research Database (Denmark)

    Hübschmann, Martin; Skladchikova, Galina

    2008-01-01

    Extracellular ATP is an abundant signaling molecule that has a number of functions in the nervous system. It is released by both neurons and glial cells, activates purinergic receptors and acts as a trophic factor as well as a neurotransmitter. In this review, we summarize the evidence for a direct...... ATP-NCAM interaction and discuss its functional implications. The ectodomain of NCAM contains the ATP binding Walker motif A and has intrinsic ATPase activity, which could modulate NCAM-dependent signaling processes. NCAM interacts directly with and signals through FGFR. The NCAM binding site to ATP...... overlaps with the site of NCAM-FGFR interaction, and ATP is capable of disrupting NCAM-FGFR binding. This implies that NCAM signaling through FGFR can be regulated by ATP, which is supported by the observation that ATP can abrogate NCAM-induced neurite outgrowth. Finally, ATP can induce NCAM ectodomain...

  13. Comparison of two-phase and three-phase methanol synthesis processes

    NARCIS (Netherlands)

    van de Graaf, G.H; Beenackers, A.A C M

    1996-01-01

    A comparison is made between the ICI (two-phase) methanol synthesis process and a three-phase slurry process based on a multi-stage agitated reactor. The process calculations are based on a complete reactor system consisting of the reactor itself, a recycling system and a gas-liquid separator. The b

  14. Comparison of two-phase and three-phase methanol synthesis processes

    NARCIS (Netherlands)

    van de Graaf, G.H; Beenackers, A.A C M

    1996-01-01

    A comparison is made between the ICI (two-phase) methanol synthesis process and a three-phase slurry process based on a multi-stage agitated reactor. The process calculations are based on a complete reactor system consisting of the reactor itself, a recycling system and a gas-liquid separator. The

  15. Investigation on two-phase flow instability in steam generator of integrated nuclear reactor

    Institute of Scientific and Technical Information of China (English)

    1996-01-01

    In the pressure range of 3-18MPa,high pressure steam-water two-phase flow density wave instability in vertical upward parallel pipes with inner diameter of 12mm is studied experimentally.The oscillation curves of two-phase flow instability and the effects of several parameters on the oscillation threshold of the system are obtained.Based on the small pertubation linearization method and the stability principles of automatic control system,a mathematical model is developed to predict the characteristics of density wave instability threshold.The predictions of the model are in good agreement with the experimental results.

  16. Determination of production-shipment policy using a two-phase algebraic approach

    Directory of Open Access Journals (Sweden)

    Huei-Hsin Chang

    2012-04-01

    Full Text Available The optimal production-shipment policy for end products using mathematicalmodeling and a two-phase algebraic approach is investigated. A manufacturing systemwith a random defective rate, a rework process, and multiple deliveries is studied with thepurpose of deriving the optimal replenishment lot size and shipment policy that minimisestotal production-delivery costs. The conventional method uses differential calculus on thesystem cost function to determine the economic lot size and optimal number of shipmentsfor such an integrated vendor-buyer system, whereas the proposed two-phase algebraicapproach is a straightforward method that enables practitioners who may not havesufficient knowledge of calculus to manage real-world systems more effectively.

  17. Characterizing dynamic hysteresis and fractal statistics of chaotic two-phase flow and application to fuel cells

    Science.gov (United States)

    Burkholder, Michael B.; Litster, Shawn

    2016-05-01

    In this study, we analyze the stability of two-phase flow regimes and their transitions using chaotic and fractal statistics, and we report new measurements of dynamic two-phase pressure drop hysteresis that is related to flow regime stability and channel water content. Two-phase flow dynamics are relevant to a variety of real-world systems, and quantifying transient two-phase flow phenomena is important for efficient design. We recorded two-phase (air and water) pressure drops and flow images in a microchannel under both steady and transient conditions. Using Lyapunov exponents and Hurst exponents to characterize the steady-state pressure fluctuations, we develop a new, measurable regime identification criteria based on the dynamic stability of the two-phase pressure signal. We also applied a new experimental technique by continuously cycling the air flow rate to study dynamic hysteresis in two-phase pressure drops, which is separate from steady-state hysteresis and can be used to understand two-phase flow development time scales. Using recorded images of the two-phase flow, we show that the capacitive dynamic hysteresis is related to channel water content and flow regime stability. The mixed-wettability microchannel and in-channel water introduction used in this study simulate a polymer electrolyte fuel cell cathode air flow channel.

  18. Characterizing dynamic hysteresis and fractal statistics of chaotic two-phase flow and application to fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Burkholder, Michael B.; Litster, Shawn, E-mail: litster@andrew.cmu.edu [Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, Pennsylvania 15213 (United States)

    2016-05-15

    In this study, we analyze the stability of two-phase flow regimes and their transitions using chaotic and fractal statistics, and we report new measurements of dynamic two-phase pressure drop hysteresis that is related to flow regime stability and channel water content. Two-phase flow dynamics are relevant to a variety of real-world systems, and quantifying transient two-phase flow phenomena is important for efficient design. We recorded two-phase (air and water) pressure drops and flow images in a microchannel under both steady and transient conditions. Using Lyapunov exponents and Hurst exponents to characterize the steady-state pressure fluctuations, we develop a new, measurable regime identification criteria based on the dynamic stability of the two-phase pressure signal. We also applied a new experimental technique by continuously cycling the air flow rate to study dynamic hysteresis in two-phase pressure drops, which is separate from steady-state hysteresis and can be used to understand two-phase flow development time scales. Using recorded images of the two-phase flow, we show that the capacitive dynamic hysteresis is related to channel water content and flow regime stability. The mixed-wettability microchannel and in-channel water introduction used in this study simulate a polymer electrolyte fuel cell cathode air flow channel.

  19. A Derivation of the Nonlocal Volume-Averaged Equations for Two-Phase Flow Transport

    Directory of Open Access Journals (Sweden)

    Gilberto Espinosa-Paredes

    2012-01-01

    Full Text Available In this paper a detailed derivation of the general transport equations for two-phase systems using a method based on nonlocal volume averaging is presented. The local volume averaging equations are commonly applied in nuclear reactor system for optimal design and safe operation. Unfortunately, these equations are limited to length-scale restriction and according with the theory of the averaging volume method, these fail in transition of the flow patterns and boundaries between two-phase flow and solid, which produce rapid changes in the physical properties and void fraction. The non-local volume averaging equations derived in this work contain new terms related with non-local transport effects due to accumulation, convection diffusion and transport properties for two-phase flow; for instance, they can be applied in the boundary between a two-phase flow and a solid phase, or in the boundary of the transition region of two-phase flows where the local volume averaging equations fail.

  20. Gas-liquid two-phase flow across a bank of micropillars

    Science.gov (United States)

    Krishnamurthy, Santosh; Peles, Yoav

    2007-04-01

    Adiabatic nitrogen-water two-phase flow across a bank of staggered circular micropillars, 100μm long with a diameter of 100μm and a pitch-to-diameter ratio of 1.5, was investigated experimentally for Reynolds number ranging from 5 to 50. Flow patterns, void fraction, and pressure drop were obtained, discussed, and compared to large scale as well as microchannel results. Two-phase flow patterns were determined by flow visualization, and a flow map was constructed as a function of gas and liquid superficial velocities. Significant deviations from conventional scale systems, with respect to flow patterns and trend lines, were observed. A unique flow pattern, driven by surface tension, was observed and termed bridge flow. The applicability of conventional scale models to predict the void fraction and two-phase frictional pressure drop was also assessed. Comparison with a conventional scale void fraction model revealed good agreement, but was found to be in a physically wrong form. Thus, a modified physically based model for void fraction was developed. A two-phase frictional multiplier was found to be a strong function of mass flux, unlike in previous microchannel studies. It was observed that models from conventional scale systems did not adequately predict the two-phase frictional multiplier at the microscale, thus, a modified model accounting for mass flux was developed.

  1. New Results in Two-Phase Pressure Drop Calculations at Reduced Gravity Conditions

    Science.gov (United States)

    Braisted, Jon; Kurwitz, Cable; Best, Frederick

    2004-02-01

    The mass, power, and volume energy savings of two-phase systems for future spacecraft creates many advantages over current single-phase systems. Current models of two-phase phenomena such as pressure drop, void fraction, and flow regime prediction are still not well defined for space applications. Commercially available two-phase modeling software has been developed for a large range of acceleration fields including reduced-gravity conditions. Recently, a two-phase experiment has been flown to expand the two-phase database. A model of the experiment was created in the software to determine how well the software could predict the pressure drop observed in the experiment. Of the simulations conducted, the computer model shows good agreement of the pressure drop in the experiment to within 30%. However, the software does begin to over-predict pressure drop in certain regions of a flow regime map indicating that some models used in the software package for reduced-gravity modeling need improvement.

  2. Reduced-gravity two-phase flow experiments in the NASA KC-135

    Science.gov (United States)

    Cuta, Judith M.; Michener, Thomas E.; Best, Frederick R.; Kachnik, Leo J.

    1988-01-01

    An adequate understanding is sought of flow and heat transfer behavior in reduced and zero gravity conditions. Microgravity thermal-hydraulic analysis capabilities were developed for application to space nuclear power systems. A series of reduced gravity two phase flow experiments using the NASA KC-135 were performed. The objective was to supply basic thermal hydraulic information that could be used in development of analytical tools for design of space power systems. The experiments are described. Two main conclusions were drawn. First, the tests demonstrate that the KC-135 is a suitable test environment for obtaining two phase flow and heat transfer data in reduced gravity conditions. Second, the behavior of two phase flow in low gravity is sufficiently different from that obtained in 1 g to warrant intensive investigation of the phenomenon if adequate analytical tools are to be developed for microgravity conditions.

  3. DYNAMIC MODELING STRATEGY FOR FLOW REGIME TRANSITION IN GAS-LIQUID TWO-PHASE FLOWS

    Energy Technology Data Exchange (ETDEWEB)

    X. Wang; X. Sun; H. Zhao

    2011-09-01

    In modeling gas-liquid two-phase flows, the concept of flow regime has been used to characterize the global interfacial structure of the flows. Nearly all constitutive relations that provide closures to the interfacial transfers in two-phase flow models, such as the two-fluid model, are often flow regime dependent. Currently, the determination of the flow regimes is primarily based on flow regime maps or transition criteria, which are developed for steady-state, fully-developed flows and widely applied in nuclear reactor system safety analysis codes, such as RELAP5. As two-phase flows are observed to be dynamic in nature (fully-developed two-phase flows generally do not exist in real applications), it is of importance to model the flow regime transition dynamically for more accurate predictions of two-phase flows. The present work aims to develop a dynamic modeling strategy for determining flow regimes in gas-liquid two-phase flows through the introduction of interfacial area transport equations (IATEs) within the framework of a two-fluid model. The IATE is a transport equation that models the interfacial area concentration by considering the creation and destruction of the interfacial area, such as the fluid particle (bubble or liquid droplet) disintegration, boiling and evaporation; and fluid particle coalescence and condensation, respectively. For the flow regimes beyond bubbly flows, a two-group IATE has been proposed, in which bubbles are divided into two groups based on their size and shape (which are correlated), namely small bubbles and large bubbles. A preliminary approach to dynamically identifying the flow regimes is provided, in which discriminators are based on the predicted information, such as the void fraction and interfacial area concentration of small bubble and large bubble groups. This method is expected to be applied to computer codes to improve their predictive capabilities of gas-liquid two-phase flows, in particular for the applications in

  4. Mathematical modeling of disperse two-phase flows

    CERN Document Server

    Morel, Christophe

    2015-01-01

    This book develops the theoretical foundations of disperse two-phase flows, which are characterized by the existence of bubbles, droplets or solid particles finely dispersed in a carrier fluid, which can be a liquid or a gas. Chapters clarify many difficult subjects, including modeling of the interfacial area concentration. Basic knowledge of the subjects treated in this book is essential to practitioners of Computational Fluid Dynamics for two-phase flows in a variety of industrial and environmental settings. The author provides a complete derivation of the basic equations, followed by more advanced subjects like turbulence equations for the two phases (continuous and disperse) and multi-size particulate flow modeling. As well as theoretical material, readers will discover chapters concerned with closure relations and numerical issues. Many physical models are presented, covering key subjects including heat and mass transfers between phases, interfacial forces and fluid particles coalescence and breakup, a...

  5. A SAS Package for Logistic Two-Phase Studies

    Directory of Open Access Journals (Sweden)

    Walter Schill

    2014-04-01

    Full Text Available Two-phase designs, in which for a large study a dichotomous outcome and partial or proxy information on risk factors is available, whereas precise or complete measurements on covariates have been obtained only in a stratified sub-sample, extend the standard case-control design and have been proven useful in practice. The application of two-phase designs, however, seems to be hampered by the lack of appropriate, easy-to-use software. This paper introduces sas-twophase-package, a collection of SAS-macros, to fulfill this task. sas-twophase-package implements weighted likelihood, pseudo likelihood and semi- parametric maximum likelihood estimation via the EM algorithm and via profile likelihood in two-phase settings with dichotomous outcome and a given stratification.

  6. Two-Phase flow instrumentation for nuclear accidents simulation

    Science.gov (United States)

    Monni, G.; De Salve, M.; Panella, B.

    2014-11-01

    The paper presents the research work performed at the Energy Department of the Politecnico di Torino, concerning the development of two-phase flow instrumentation and of models, based on the analysis of experimental data, that are able to interpret the measurement signals. The study has been performed with particular reference to the design of power plants, such as nuclear water reactors, where the two-phase flow thermal fluid dynamics must be accurately modeled and predicted. In two-phase flow typically a set of different measurement instruments (Spool Piece - SP) must be installed in order to evaluate the mass flow rate of the phases in a large range of flow conditions (flow patterns, pressures and temperatures); moreover, an interpretative model of the SP need to be developed and experimentally verified. The investigated meters are: Turbine, Venturi, Impedance Probes, Concave sensors, Wire mesh sensor, Electrical Capacitance Probe. Different instrument combinations have been tested, and the performance of each one has been analyzed.

  7. A mechanical erosion model for two-phase mass flows

    CERN Document Server

    Pudasaini, Shiva P

    2016-01-01

    Erosion, entrainment and deposition are complex and dominant, but yet poorly understood, mechanical processes in geophysical mass flows. Here, we propose a novel, process-based, two-phase, erosion-deposition model capable of adequately describing these complex phenomena commonly observed in landslides, avalanches, debris flows and bedload transport. The model is based on the jump in the momentum flux including changes of material and flow properties along the flow-bed interface and enhances an existing general two-phase mass flow model (Pudasaini, 2012). A two-phase variably saturated erodible basal morphology is introduced and allows for the evolution of erosion-deposition-depths, incorporating the inherent physical process including momentum and rheological changes of the flowing mixture. By rigorous derivation, we show that appropriate incorporation of the mass and momentum productions or losses in conservative model formulation is essential for the physically correct and mathematically consistent descript...

  8. Simulating confined swirling gas-solid two phase jet

    Institute of Scientific and Technical Information of China (English)

    金晗辉; 夏钧; 樊建人; 岑可法

    2002-01-01

    A k-ε-kp multi-fluid model was used to simulate confined swirling gas-solid two phase jet comprised of particle-laden flow from a center tube and a swirling air stream entering the test section from the coaxial annular. After considering the drag force between the two phases and gravity, a series of numerical simulations of the two-phase flow of 30μm, 45μm, 60μm diameter particles were performed on a x×r=50×50 mesh grid respectively. The results showed that the k-ε-kp multi-fluid model can be applied to predict moderate swirling multi-phase flow. When the particle diameter is large, the collision of the particles with the wall will influence the prediction accuracy. The bigger the diameter of the particles, the stronger the collision with the wall, and the more obvious the difference between measured and calculated results.

  9. Dynamic Modeling of Phase Crossings in Two-Phase Flow

    DEFF Research Database (Denmark)

    Madsen, Søren; Veje, Christian; Willatzen, Morten

    2012-01-01

    of the variables and are usually very slow to evaluate. To overcome these challenges, we use an interpolation scheme with local refinement. The simulations show that the method handles crossing of the saturation lines for both liquid to two-phase and two-phase to gas regions. Furthermore, a novel result obtained...... in this work, the method is stable towards dynamic transitions of the inlet/outlet boundaries across the saturation lines. Results for these cases are presented along with a numerical demonstration of conservation of mass under dynamically varying boundary conditions. Finally we present results...

  10. Shock wave of vapor-liquid two-phase flow

    Institute of Scientific and Technical Information of China (English)

    Liangju ZHAO; Fei WANG; Hong GAO; Jingwen TANG; Yuexiang YUAN

    2008-01-01

    The shock wave of vapor-liquid two-phase flow in a pressure-gain steam injector is studied by build-ing a mathematic model and making calculations. The results show that after the shock, the vapor is nearly com-pletely condensed. The upstream Mach number and the volume ratio of vapor have a great effect on the shock. The pressure and Mach number of two-phase shock con-form to the shock of ideal gas. The analysis of available energy shows that the shock is an irreversible process with entropy increase.

  11. Two Phase Flow and Space-Based Applications

    Science.gov (United States)

    McQuillen, John

    1999-01-01

    A reduced gravity environment offers the ability to remove the effect of buoyancy on two phase flows whereby density differences that normally would promote relative velocities between the phases and also alter the shape of the interface are removed. However, besides being a potent research tool, there are also many space-based technologies that will either utilize or encounter two-phase flow behavior, and as a consequence, several questions must be addressed. This paper presents some of these technologies missions. Finally, this paper gives a description of web-sites for some funding.

  12. 独立光伏发电系统中双向变换器的软起动策略%Two-phase soft start strategy for bi-directional DC-DC converter in solar cell stand-alone photovoltaic power system

    Institute of Scientific and Technical Information of China (English)

    张新华; 廖志凌; 杨孟雄

    2009-01-01

    Bi-directional converter applied to solar cell stand-alone photovoltaic power system belongs to the double sources application. Due to complemented operation of switches in bi-directional converter, traditional soft start method will give rise to large inverse inductor current from the output source at double sources application, and result in damage of converter. This paper proposes a novel soft start method-two-phase soft start method to achieve soft start for bi-directional converter of double sources. By implementing soft start of both active switch and passive switch, two-phase soft start method can realize bi-directional converter soft start at double sources application, avoiding inverse inductor current. Two-phase soft start method applies to a series of bi-directional converter. Experimental results are finally given to verify the effectiveness and validity of two-phase soft start method for bi-directional converter of double sources.%双向变换器在太阳能独立光伏发电系统中属于两端"源"的运用场合,采用传统的软起动方法,由于功率开关管互补导通,会从输出端"源"引入反向电感电流,导致变换器损坏.为了实现双向变换器在两端"源"情况下的开机软起动,提出了一种新颖的双向变换器两段式软起动方法,通过对主控管和被控管实施软起动,避免产生反向电感电流,该方法也适用于一族的双向变换器.最后给出了实验结果,验证了两端"源"双向变换器两段式软起动方法的有效性和正确性.

  13. Multi-needle capacitance probe for non-conductive two-phase flows

    Science.gov (United States)

    Monrós-Andreu, G.; Martinez-Cuenca, R.; Torró, S.; Escrig, J.; Hewakandamby, B.; Chiva, S.

    2016-07-01

    Despite its variable degree of application, intrusive instrumentation is the most accurate way to obtain local information in a two-phase flow system, especially local interfacial velocity and local interfacial area parameters. In this way, multi-needle probes, based on conductivity or optical principles, have been extensively used in the past few decades by many researchers in two-phase flow investigations. Moreover, the signal processing methods used to obtain the time-averaged two-phase flow parameters in this type of sensor have been thoroughly discussed and validated by many experiments. The objective of the present study is to develop a miniaturized multi-needle probe, based on capacitance measurements applicable to a wide range of non-conductive two-phase flows and, thus, to extend the applicability of multi-needle sensor whilst also maintaining a signal processing methodology provided in the literature for conductivity probes. Results from the experiments performed assess the applicability of the proposed sensor measurement principle and signal processing method for the bubbly flow regime. These results also provide an insight into the sensor application for more complex two-phase flow regimes.

  14. Partition behaviors of oxytetracycline hydrochloride (OTC) in small molecule alcohol/salt binary aqueous two-phase system%小分子醇/盐二元双水相体系中盐酸土霉素的分配行为

    Institute of Scientific and Technical Information of China (English)

    关卫省; 柴丽; 韩娟

    2012-01-01

    Based on the aqueous two-phase system,a new method of using ethanol and re-propanol with sodium dihydrogen phosphate binary aqueous two-phase system for extracting of oxytetracycline hydrochloride (OTC) was set up. The influence factors on partition behaviors of oxytetracyeline hydrochloride (OTC) were studied,including the system composition,type and amount of salts,the pH value,the extraction temperature, and standing time after centrifuge. The results showed that the binary aqueous two-phase system can be used to study the distribution of antibiotics. When the system was ethanol and n-pro-panol, NaH2 PO4 concentration of 48% , the pH value was 4~ 5, temperature was 25℃, and standing 12 h ,the partition coefficient of oxytetracycline hydrochloride ( OTC) was 21.95, and extraction rate was 86.09%.%在双水相体系研究的基础上,建立了乙醇与正丙醇和磷酸二氢钠形成的二元双水相体系萃取盐酸土霉素的新方法,考察了小分子醇的用量、盐种类和浓度、pH值、温度以及静置时间对盐酸土霉素分配行为的影响.结果表明,小分子醇/盐二元双水相体系可用于抗生素分配行为的研究,其中体系组成为乙醇和正丙醇,磷酸二氢钠浓度在48%,pH值在4~5,温度25℃,以及静置12 h左右,盐酸土霉素在该二元双水相体系中的分配系数达到21.95,萃取率达86.09%.

  15. Entropy analysis on non-equilibrium two-phase flow models

    Energy Technology Data Exchange (ETDEWEB)

    Karwat, H.; Ruan, Y.Q. [Technische Universitaet Muenchen, Garching (Germany)

    1995-09-01

    A method of entropy analysis according to the second law of thermodynamics is proposed for the assessment of a class of practical non-equilibrium two-phase flow models. Entropy conditions are derived directly from a local instantaneous formulation for an arbitrary control volume of a structural two-phase fluid, which are finally expressed in terms of the averaged thermodynamic independent variables and their time derivatives as well as the boundary conditions for the volume. On the basis of a widely used thermal-hydraulic system code it is demonstrated with practical examples that entropy production rates in control volumes can be numerically quantified by using the data from the output data files. Entropy analysis using the proposed method is useful in identifying some potential problems in two-phase flow models and predictions as well as in studying the effects of some free parameters in closure relationships.

  16. Analytical solution of laminar-laminar stratified two-phase flows with curved interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Brauner, N.; Rovinsky, J.; Maron, D.M. [Tel-Aviv Univ. (Israel)

    1995-09-01

    The present study represents a complete analytical solution for laminar two-phase flows with curved interfaces. The solution of the Navier-Stokes equations for the two-phases in bipolar coordinates provides the `flow monograms` describe the relation between the interface curvature and the insitu flow geometry when given the phases flow rates and viscosity ratios. Energy considerations are employed to construct the `interface monograms`, whereby the characteristic interfacial curvature is determined in terms of the phases insitu holdup, pipe diameter, surface tension, fluids/wall adhesion and gravitation. The two monograms are then combined to construct the system `operational monogram`. The `operational monogram` enables the determination of the interface configuration, the local flow characteristics, such as velocity profiles, wall and interfacial shear stresses distribution as well as the integral characteristics of the two-phase flow: phases insitu holdup and pressure drop.

  17. Investigation of two-phase heat transfer coefficients of argon-freon cryogenic mixed refrigerants

    Science.gov (United States)

    Baek, Seungwhan; Lee, Cheonkyu; Jeong, Sangkwon

    2014-11-01

    Mixed refrigerant Joule Thomson refrigerators are widely used in various kinds of cryogenic systems these days. Although heat transfer coefficient estimation for a multi-phase and multi-component fluid in the cryogenic temperature range is necessarily required in the heat exchanger design of mixed refrigerant Joule Thomson refrigerators, it has been rarely discussed so far. In this paper, condensation and evaporation heat transfer coefficients of argon-freon mixed refrigerant are measured in a microchannel heat exchanger. A Printed Circuit Heat Exchanger (PCHE) with 340 μm hydraulic diameter has been developed as a compact microchannel heat exchanger and utilized in the experiment. Several two-phase heat transfer coefficient correlations are examined to discuss the experimental measurement results. The result of this paper shows that cryogenic two-phase mixed refrigerant heat transfer coefficients can be estimated by conventional two-phase heat transfer coefficient correlations.

  18. Position Control of Synchronous Motor Drive by Modified Adaptive Two-phase Sliding Mode Controller

    Institute of Scientific and Technical Information of China (English)

    Mohamed Said Sayed Ahmed; Ping Zhang; Yun-Jie Wu

    2008-01-01

    A modified adaptive two-phase sliding mode controller for the synchronous motor drive that is highly robust to uncertain-ties and external disturbances is proposed in this paper. The proposed controller uses two-phase sliding mode control (SMC) where the 1st phase mainly controls the system in steady states and disturbed states-it is a smoothing phase. The 2nd phase is used mainly in the case of disturbed states. Also, it is an autotuning phase and uses a simple adaptive algorithm to tune the gain of conventional variable structure control (VSC). The modified controller is useful in position control of a permanent magnet synchronous drive.

  19. Preliminary Two-Phase Terry Turbine Nozzle Models for RCIC Off-Design Operation Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Haihua [Idaho National Lab. (INL), Idaho Falls, ID (United States); O' Brien, James [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2017-06-12

    This report presents the effort to extend the single-phase analytical Terry turbine model to cover two-phase off-design conditions. The work includes: (1) adding well-established two-phase choking models – the Isentropic Homogenous Equilibrium Model (IHEM) and Moody’s model, and (2) theoretical development and implementation of a two-phase nozzle expansion model. The two choking models provide bounding cases for the two-phase choking mass flow rate. The new two-phase Terry turbine model uses the choking models to calculate the mass flow rate, the critical pressure at the nozzle throat, and steam quality. In the divergent stage, we only consider the vapor phase with a similar model for the single-phase case by assuming that the liquid phase would slip along the wall with a much slower speed and will not contribute the impulse on the rotor. We also modify the stagnation conditions according to two-phase choking conditions at the throat and the cross-section areas for steam flow at the nozzle throat and at the nozzle exit. The new two-phase Terry turbine model was benchmarked with the same steam nozzle test as for the single-phase model. Better agreement with the experimental data is observed than from the single-phase model. We also repeated the Terry turbine nozzle benchmark work against the Sandia CFD simulation results with the two-phase model for the pure steam inlet nozzle case. The RCIC start-up tests were simulated and compared with the single-phase model. Similar results are obtained. Finally, we designed a new RCIC system test case to simulate the self-regulated Terry turbine behavior observed in Fukushima accidents. In this test, a period inlet condition for the steam quality varying from 1 to 0 is applied. For the high quality inlet period, the RCIC system behaves just like the normal operation condition with a high pump injection flow rate and a nominal steam release rate through the turbine, with the net addition of water to the primary system; for

  20. Problems of heat transfer and hydraulics of two-phase media

    CERN Document Server

    Kutateladze, S S

    1969-01-01

    Problems of Heat Transfer and Hydraulics of Two-Phase Media presents the theory of heat transfer and hydrodynamics. This book discusses the various aspects of heat transfer and the flow of two-phase systems. Organized into two parts encompassing 22 chapters, this book starts with an overview of the laws of similarity for heat transfer to or from a flowing liquid with various physical properties and allowed for variation in viscosity and thermal conductivity. This book then explores the general functional relationship that exists between viscosity and thermal conductivity for thermodynamically

  1. Research of Characteristics of Gas-liquid Two-phase Pressure Drop in Microreactor

    OpenAIRE

    Li Dan

    2015-01-01

    With the research system of nitrogen and deionized water, this paper researches the pressure drop of gas-liquid two-phase flow in the circular microchannel with an inner diameter which is respectively 0.9mm and 0.5mm, analyzes the effect of microchannel diameter on gas-liquid two-phase frictional pressure drop in the microchannel reactor, and compares with the result of frictional pressure drop and the predicting result of divided-phase flow pattern. The result shows that, the gas-liquid two-...

  2. ATP-consuming and ATP-generating enzymes secreted by pancreas

    DEFF Research Database (Denmark)

    Yegutkin, Gennady G; Samburski, Sergei S; Jalkanen, Sirpa

    2006-01-01

    Pancreatic acini release ATP in response to various stimuli, including cholecystokinin octapeptide (CCK-8), as we show in the present study. There were indications that pancreatic juice also contains enzymes that could hydrolyze ATP during its passage through the ductal system. The aim of this st......Pancreatic acini release ATP in response to various stimuli, including cholecystokinin octapeptide (CCK-8), as we show in the present study. There were indications that pancreatic juice also contains enzymes that could hydrolyze ATP during its passage through the ductal system. The aim...... of this study was to determine which ATP-degrading and possibly ATP-generating enzymes were present in pancreatic secretion. For this purpose, pancreatic juice was collected from anesthetized rats stimulated with infusion of CCK-8. Purine-converting activities in juice samples were assayed by TLC using either...... release of both ATP-consuming and ATP-generating enzymes into pancreatic juice. This newly discovered richness of secreted enzymes underscores the importance of purine signaling between acini and pancreatic ducts lumen and implies regulation of the purine-converting enzymes release....

  3. Animal-cell culture in aqueous two-phase systems.

    NARCIS (Netherlands)

    Zijlstra, G.M.

    1998-01-01

    In current industrial biotechnology, animal-cell culture is an important source of therapeutic protein products. The conventional animal-cell production processes, however, include many unit operations as part of the fermentation and downstream processing strategy. The research described in this the

  4. Animal-cell culture in aqueous two-phase systems

    NARCIS (Netherlands)

    Zijlstra, G.M.

    1998-01-01

    In current industrial biotechnology, animal-cell culture is an important source of therapeutic protein products. The conventional animal-cell production processes, however, include many unit operations as part of the fermentation and downstream processing strategy. The research described in

  5. Modelling two-phase transport of 3H/3He

    NARCIS (Netherlands)

    Visser, A.; Schaap, J.D.; Leijnse, T.; Broers, H.P.; Bierkens, M.F.P.

    2008-01-01

    Degassing of groundwater by excess denitrification of agricultural pollution complicates the interpretation of 3H/3He data and hinders the estimation of travel times in nitrate pollution studies. In this study we used a two-phase flow and transport model (STOMP) to evaluate the method presented by

  6. Two-phase alkali-metal experiments in reduced gravity

    Energy Technology Data Exchange (ETDEWEB)

    Antoniak, Z.I.

    1986-06-01

    Future space missions envision the use of large nuclear reactors utilizing either a single or a two-phase alkali-metal working fluid. The design and analysis of such reactors require state-of-the-art computer codes that can properly treat alkali-metal flow and heat transfer in a reduced-gravity environment. A literature search of relevant experiments in reduced gravity is reported on here, and reveals a paucity of data for such correlations. The few ongoing experiments in reduced gravity are noted. General plans are put forth for the reduced-gravity experiments which will have to be performed, at NASA facilities, with benign fluids. A similar situation exists regarding two-phase alkali-metal flow and heat transfer, even in normal gravity. Existing data are conflicting and indequate for the task of modeling a space reactor using a two-phase alkali-metal coolant. The major features of past experiments are described here. Data from the reduced-gravity experiments with innocuous fluids are to be combined with normal gravity data from the two-phase alkali-metal experiments. Analyses undertaken here give every expectation that the correlations developed from this data base will provide a valid representation of alkali-metal heat transfer and pressure drop in reduced gravity.

  7. Coal-Face Fracture With A Two-Phase Liquid

    Science.gov (United States)

    Collins, E. R., Jr.

    1985-01-01

    In new method for mining coal without explosive, two-phase liquid such as CO2 and water, injected at high pressure into deeper ends of holes drilled in coal face. Liquid permeates coal seam through existing microfractures; as liquid seeps back toward face, pressure eventually drops below critical value at which dissolved gas flashvaporizes, breaking up coal.

  8. Two-phase flow in micro and nanofluidic devices

    NARCIS (Netherlands)

    Shui, Lingling

    2009-01-01

    This thesis provides experimental data and theoretical analysis on two-phase flow in devices with different layouts of micrometer or nanometer-size channels. A full flow diagram is presented for oil and water flow in head-on microfluidic devices. Morphologically different flow regimes (dripping, jet

  9. Modelling two-phase transport of 3H/3He

    NARCIS (Netherlands)

    Visser, A.; Schaap, J.D.; Leijnse, T.; Broers, H.P.; Bierkens, M.F.P.

    2008-01-01

    Degassing of groundwater by excess denitrification of agricultural pollution complicates the interpretation of 3H/3He data and hinders the estimation of travel times in nitrate pollution studies. In this study we used a two-phase flow and transport model (STOMP) to evaluate the method presented by V

  10. Experimental Investigation of two-phase nitrogen Cryo transfer line

    Science.gov (United States)

    Singh, G. K.; Nimavat, H.; Panchal, R.; Garg, A.; Srikanth, GLN; Patel, K.; Shah, P.; Tanna, V. L.; Pradhan, S.

    2017-02-01

    A 6-m long liquid nitrogen based cryo transfer line has been designed, developed and tested at IPR. The test objectives include the thermo-hydraulic characteristics of Cryo transfer line under single phase as well as two phase flow conditions. It is always easy in experimentation to investigate the thermo-hydraulic parameters in case of single phase flow of cryogen but it is real challenge when one deals with the two phase flow of cryogen due to availibity of mass flow measurements (direct) under two phase flow conditions. Established models have been reported in the literature where one of the well-known model of Lockhart-Martenelli relationship has been used to determine the value of quality at the outlet of Cryo transfer line. Under homogenous flow conditions, by taking the ratio of the single-phase pressure drop and the two-phase pressure drop, we estimated the quality at the outlet. Based on these equations, vapor quality at the outlet of the transfer line was predicted at different heat loads. Experimental rresults shown that from inlet to outlet, there is a considerable increment in the pressure drop and vapour quality of the outlet depending upon heat load and mass flow rate of nitrogen flowing through the line.

  11. Numerical simulation of two-phase flow in offshore environments

    NARCIS (Netherlands)

    Wemmenhove, Rik

    2008-01-01

    Numerical Simulation of Two-Phase Flow in Offshore Environments Rik Wemmenhove Weather conditions on full sea are often violent, leading to breaking waves and lots of spray and air bubbles. As high and steep waves may lead to severe damage on ships and offshore structures, there is a great need for

  12. TWO-PHASE EJECTOR of CARBON DIOXIDE HEAT PUMP CALCULUS

    Directory of Open Access Journals (Sweden)

    Sit B.M.

    2010-12-01

    Full Text Available It is presented the calculus of the two-phase ejector for carbon dioxide heat pump. The method of calculus is based on the method elaborated by S.M. Kandil, W.E. Lear, S.A. Sherif, and is modified taking into account entrainment ratio as the input for the calculus.

  13. Investigation of the overall transient performance of the industrial two-phase closed loop thermosyphon

    NARCIS (Netherlands)

    Vincent, Charles C.J.; Kok, Jacobus B.W.

    1992-01-01

    The two-phase closed loop thermosyphon is investigated with emphasis on the overall performance in transient operation. The control volume approach is the base of a global analysis describing the motion of vapor and liquid phases of the thermosyphon system in one-dimensional equations. Interfacial s

  14. Measurements of solids concentration and axial solids velocity in gas-solid two-phase flows.

    NARCIS (Netherlands)

    Nieuwland, J.J.; Meijer, R.; Kuipers, J.A.M.; Swaaij, van W.P.M.

    1996-01-01

    Several techniques reported in the literature for measuring solids concentration and solids velocity in (dense) gas-solid two-phase flow have been briefly reviewed. An optical measuring system, based on detection of light reflected by the suspended particles, has been developed to measure local soli

  15. A FINITE ELEMENT COLLOCATION METHOD FOR TWO-PHASE INCOMPRESSIBLE IMMISCIBLE PROBLEMS

    Institute of Scientific and Technical Information of China (English)

    Ma Ning

    2007-01-01

    Two-phase, incompressible, immiscible flow in porous media is governed by a coupled system of nonlinear partial differential equations. The pressure equation is elliptic,whereas the concentration equation is parabolic, and both are treated by the collocation scheme. Existence and uniqueness of solutions of the algorithm are proved. A optimal convergence analysis is given for the method.

  16. Generating a Two-Phase Lesson for Guiding Beginners to Learn Basic Dance Movements

    Science.gov (United States)

    Yang, Yang; Leung, Howard; Yue, Lihua; Deng, Liqun

    2013-01-01

    In this paper, an automated lesson generation system for guiding beginners to learn basic dance movements is proposed. It analyzes the dance to generate a two-phase lesson which can provide a suitable cognitive load thus offering an efficient learning experience. In the first phase, the dance is divided into small pieces which are patterns, and…

  17. THE LINEAR HOMOGENEOUS FLOW MODEL FOR TWO-PHASE FLOW INSTABILITY IN BOILING CHANNELS

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    This paper presents liner homogeneous model describing two-phase flow instability. Dimensionless parameter η was derived by using the linear homogeneous model. Using parameter η the stability of a system could be easily judged. The calculated results agree with the experimental data well.

  18. Generating a Two-Phase Lesson for Guiding Beginners to Learn Basic Dance Movements

    Science.gov (United States)

    Yang, Yang; Leung, Howard; Yue, Lihua; Deng, Liqun

    2013-01-01

    In this paper, an automated lesson generation system for guiding beginners to learn basic dance movements is proposed. It analyzes the dance to generate a two-phase lesson which can provide a suitable cognitive load thus offering an efficient learning experience. In the first phase, the dance is divided into small pieces which are patterns, and…

  19. Investigations of two-phase flame propagation under microgravity conditions

    Science.gov (United States)

    Gokalp, Iskender

    2016-07-01

    Investigations of two-phase flame propagation under microgravity conditions R. Thimothée, C. Chauveau, F. Halter, I Gökalp Institut de Combustion, Aérothermique, Réactivité et Environnement (ICARE), CNRS, 1C Avenue de la Recherche Scientifique, 45071 Orléans Cedex 2, France This paper presents and discusses recent results on two-phase flame propagation experiments we carried out with mono-sized ethanol droplet aerosols under microgravity conditions. Fundamental studies on the flame propagation in fuel droplet clouds or sprays are essential for a better understanding of the combustion processes in many practical applications including internal combustion engines for cars, modern aircraft and liquid rocket engines. Compared to homogeneous gas phase combustion, the presence of a liquid phase considerably complicates the physico-chemical processes that make up combustion phenomena by coupling liquid atomization, droplet vaporization, mixing and heterogeneous combustion processes giving rise to various combustion regimes where ignition problems and flame instabilities become crucial to understand and control. Almost all applications of spray combustion occur under high pressure conditions. When a high pressure two-phase flame propagation is investigated under normal gravity conditions, sedimentation effects and strong buoyancy flows complicate the picture by inducing additional phenomena and obscuring the proper effect of the presence of the liquid droplets on flame propagation compared to gas phase flame propagation. Conducting such experiments under reduced gravity conditions is therefore helpful for the fundamental understanding of two-phase combustion. We are considering spherically propagating two-phase flames where the fuel aerosol is generated from a gaseous air-fuel mixture using the condensation technique of expansion cooling, based on the Wilson cloud chamber principle. This technique is widely recognized to create well-defined mono-size droplets

  20. Surfactant-coated Candida rugosa Lipase as Catalyst for Hydrolysis of Olive Oil in Solvent-Free Two-Phase System%表面活性剂包衣Candida rugosa脂肪酶在无溶剂下油水两相体系中催化橄榄油水解

    Institute of Scientific and Technical Information of China (English)

    宋宝东; 丁辉; 吴金川; Hayashi Y; Talukder MMR; 王世昌

    2003-01-01

    The surfactant-coated Candida rugosa lipase was used as catalyst for hydrolysis of olive oil in two-phase system consisting of olive oil and phosphate buffer without organic solvent. For both the coated and native lipases,the optimal buffer/oil volume ratio of 1.0, aqueous pH 6.8 and reaction temperature 30℃ were determined. The maximum activity of the coated lipase was ca 1.3 times than that of the native lipase. The half-life of the coated lipase in olive oil and the native lipase in phosphate buffer was ca 9 h and 12 h, and the final residual activity was 27% and 20% of their initial values, respectively. The final substrate conversion by the coated lipase was ca 20% higher than that of the native lipase.