WorldWideScience

Sample records for two-grid ion optics

  1. Optical Barium Ion Qubit

    CERN Document Server

    Yum, Dahyun; Dutta, Tarun; Mukherjee, Manas

    2016-01-01

    We demonstrate an optical single qubit based on 6S1/2 to 5D5/2 quadrupole transition of a single Ba+ ion operated by diode based lasers only. The resonance wavelength of the 6S1/2 to 5D5/2 quadrupole transition is about 1762 nm which suitably falls close to the U-band of the telecommunication wavelength. Thus this qubit is a naturally attractive choice towards implementation of quantum repeater or quantum networks using existing telecommunication networks. We observe continuous bit-flip oscillations at a rate of about 250 kHz which is fast enough for the qubit operation as compared to the measured coherence time of over 3 ms. We also present a technique to quantify the bit-flip error in each qubit NOT gate operation.

  2. Ion optics of RHIC electron beam ion source

    Energy Technology Data Exchange (ETDEWEB)

    Pikin, A.; Alessi, J.; Beebe, E.; Kponou, A.; Okamura, M.; Raparia, D.; Ritter, J.; Tan, Y. [Brookhaven National Laboratory, Upton, New York 11973 (United States); Kuznetsov, G. [Budker Institute of Nuclear Physics, Novosibirsk 630090 (Russian Federation)

    2012-02-15

    RHIC electron beam ion source has been commissioned to operate as a versatile ion source on RHIC injection facility supplying ion species from He to Au for Booster. Except for light gaseous elements RHIC EBIS employs ion injection from several external primary ion sources. With electrostatic optics fast switching from one ion species to another can be done on a pulse to pulse mode. The design of an ion optical structure and the results of simulations for different ion species are presented. In the choice of optical elements special attention was paid to spherical aberrations for high-current space charge dominated ion beams. The combination of a gridded lens and a magnet lens in LEBT provides flexibility of optical control for a wide range of ion species to satisfy acceptance parameters of RFQ. The results of ion transmission measurements are presented.

  3. Additive Manufacturing of Ion Thruster Optics Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Plasma Controls will manufacture and test a set of ion optics for electric propulsion ion thrusters using additive manufacturing technology, also known as 3D...

  4. Long lifetimes in optical ion traps

    CERN Document Server

    Lambrecht, Alexander; Weckesser, Pascal; Debatin, Markus; Karpa, Leon; Schaetz, Tobias

    2016-01-01

    We report on single Barium ions confined in a near-infrared optical dipole trap for up to three seconds in absence of any radio-frequency fields. Additionally, the lifetime in a visible optical dipole trap is increased by two orders of magnitude as compared to the state-of-the-art using an efficient repumping method. We characterize the state-dependent potentials and measure an upper bound for the heating rate in the near-infrared trap. These findings are beneficial for entering the regime of ultracold interaction in atom-ion ensembles exploiting bichromatic optical dipole traps. Long lifetimes and low scattering rates are essential to reach long coherence times for quantum simulations in optical lattices employing many ions, or ions and atoms.

  5. An ion-optical bench for testing ion source lenses

    Science.gov (United States)

    Stoffels, J. J.; Ells, D. R.

    1988-06-01

    An ion-optical bench has been designed and constructed to obtain experimental data on the focusing properties of ion lenses in three dimensions. The heart of the apparatus is a position-sensitive detector (PSD) that gives output signals proportional to the x and y positions of each ion impact. The position signals can be displayed on an oscilloscope screen and analyzed by a two-parameter pulse-height analyzer, thereby giving a visual picture of the ion beam cross section and intensity distribution. The PSD itself is mounted on a track and is movable during operation from a position immediately following the ion lens to 30 cm away. This enables the rapid collection of accurate data on the intensity distribution and divergence angles of ions leaving the source lens. Examples of ion lens measurements are given.

  6. Integrated optical addressing of an ion qubit

    CERN Document Server

    Mehta, Karan K; McConnell, Robert; Ram, Rajeev J; Sage, Jeremy M; Chiaverini, John

    2015-01-01

    Scalable implementation of the optics required to control trapped atomic ions' quantum states will be required to construct large-scale ion trap quantum information processors. All experiments in ion traps so far have employed approaches cumbersome to scale to even a few tens of qubits, with the majority relying on manipulation of free space beams with bulk optics. Here we demonstrate lithographically defined nanophotonic dielectric waveguides integrated within a linear surface-electrode ion trap chip, and qubit addressing at multiple locations via focusing grating couplers that emit through openings in the trap electrodes to an ion trapped 50 $\\mu$m above the chip. We perform quantum coherent operations using visible light routed in and emitted from silicon nitride waveguides and couplers, on the optical qubit transition in individual $^{88}$Sr$^+$ ions. The addressing beam is focused near the ion position with a 2 $\\mu$m 1/$e^2$-radius along the trap axis, and we measure crosstalk errors between $10^{-2}$ a...

  7. Integrated optical addressing of an ion qubit.

    Science.gov (United States)

    Mehta, Karan K; Bruzewicz, Colin D; McConnell, Robert; Ram, Rajeev J; Sage, Jeremy M; Chiaverini, John

    2016-12-01

    The long coherence times and strong Coulomb interactions afforded by trapped ion qubits have enabled realizations of the necessary primitives for quantum information processing and the highest-fidelity quantum operations in any qubit to date. Although light delivery to each individual ion in a system is essential for general quantum manipulations and readout, experiments so far have employed optical systems that are cumbersome to scale to even a few tens of qubits. Here we demonstrate lithographically defined nanophotonic waveguide devices for light routing and ion addressing that are fully integrated within a surface-electrode ion trap chip. Ion qubits are addressed at multiple locations via focusing grating couplers emitting through openings in the trap electrodes to ions trapped 50 μm above the chip; using this light, we perform quantum coherent operations on the optical qubit transition in individual (88)Sr(+) ions. The grating focuses the beam to a diffraction-limited spot near the ion position with 2 μm 1/e(2) radius along the trap axis, and we measure crosstalk errors between 10(-2) and 4 × 10(-4) at distances 7.5-15 μm from the beam centre. Owing to the scalability of the planar fabrication technique employed, together with the tight focusing and stable alignment afforded by the integration of the optics within the trap chip, this approach presents a path to creating the optical systems required for large-scale trapped-ion quantum information processing.

  8. Integrated optical addressing of an ion qubit

    Science.gov (United States)

    Mehta, Karan K.; Bruzewicz, Colin D.; McConnell, Robert; Ram, Rajeev J.; Sage, Jeremy M.; Chiaverini, John

    2016-12-01

    The long coherence times and strong Coulomb interactions afforded by trapped ion qubits have enabled realizations of the necessary primitives for quantum information processing and the highest-fidelity quantum operations in any qubit to date. Although light delivery to each individual ion in a system is essential for general quantum manipulations and readout, experiments so far have employed optical systems that are cumbersome to scale to even a few tens of qubits. Here we demonstrate lithographically defined nanophotonic waveguide devices for light routing and ion addressing that are fully integrated within a surface-electrode ion trap chip. Ion qubits are addressed at multiple locations via focusing grating couplers emitting through openings in the trap electrodes to ions trapped 50 μm above the chip; using this light, we perform quantum coherent operations on the optical qubit transition in individual 88Sr+ ions. The grating focuses the beam to a diffraction-limited spot near the ion position with 2 μm 1/e2 radius along the trap axis, and we measure crosstalk errors between 10-2 and 4 × 10-4 at distances 7.5-15 μm from the beam centre. Owing to the scalability of the planar fabrication technique employed, together with the tight focusing and stable alignment afforded by the integration of the optics within the trap chip, this approach presents a path to creating the optical systems required for large-scale trapped-ion quantum information processing.

  9. Optical surfacing via linear ion source

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Lixiang, E-mail: wulx@hdu.edu.cn [Key Lab of RF Circuits and Systems of Ministry of Education, Zhejiang Provincial Key Lab of LSI Design, Microelectronics CAD Center, College of Electronics and Information, Hangzhou Dianzi University, Hangzhou (China); Wei, Chaoyang, E-mail: siomwei@siom.ac.cn [Key Laboratory of Materials for High Power Laser, Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, Shanghai 201800 (China); Shao, Jianda, E-mail: jdshao@siom.ac.cn [Key Laboratory of Materials for High Power Laser, Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, Shanghai 201800 (China)

    2017-04-15

    We present a concept of surface decomposition extended from double Fourier series to nonnegative sinusoidal wave surfaces, on the basis of which linear ion sources apply to the ultra-precision fabrication of complex surfaces and diffractive optics. The modified Fourier series, or sinusoidal wave surfaces, build a relationship between the fabrication process of optical surfaces and the surface characterization based on power spectral density (PSD) analysis. Also, we demonstrate that the one-dimensional scanning of linear ion source is applicable to the removal of mid-spatial frequency (MSF) errors caused by small-tool polishing in raster scan mode as well as the fabrication of beam sampling grating of high diffractive uniformity without a post-processing procedure. The simulation results show that optical fabrication with linear ion source is feasible and even of higher output efficiency compared with the conventional approach.

  10. Calculation Of Extraction Optics For Ion System With Plazma Emitter

    CERN Document Server

    Frolov, B A

    2004-01-01

    The 2-D code for simulating of ion optics system of positive ion extraction from a plasma source is described. Example calculation of 100 kV optics for the extraction ion IHEP gun is presented. The trajectories of particles and emittance plots are resulted. The aberrations influ-ence strongly on ion optics for considered geometry.

  11. Mechanical Design of Carbon Ion Optics

    Science.gov (United States)

    Haag, Thomas

    2005-01-01

    Carbon Ion Optics are expected to provide much longer thruster life due to their resistance to sputter erosion. There are a number of different forms of carbon that have been used for fabricating ion thruster optics. The mechanical behavior of carbon is much different than that of most metals, and poses unique design challenges. In order to minimize mission risk, the behavior of carbon must be well understood, and components designed within material limitations. Thermal expansion of the thruster structure must be compatible with thermal expansion of the carbon ion optics. Specially designed interfaces may be needed so that grid gap and aperture alignment are not adversely affected by dissimilar material properties within the thruster. The assembled thruster must be robust and tolerant of launch vibration. The following paper lists some of the characteristics of various carbon materials. Several past ion optics designs are discussed, identifying strengths and weaknesses. Electrostatics and material science are not emphasized so much as the mechanical behavior and integration of grid electrodes into an ion thruster.

  12. Direct laser cooling Al+ ions optical clocks

    CERN Document Server

    Zhang, J; Luo, J; Lu, Z H

    2016-01-01

    Al$^+$ ions optical clock is a very promising optical frequency standard candidate due to its extremely small blackbody radiation shift. It has been successfully demonstrated with indirect cooled, quantum-logic-based spectroscopy technique. Its accuracy is limited by second-order Doppler shift, and its stability is limited by the number of ions that can be probed in quantum logic processing. We propose a direct laser cooling scheme of Al$^+$ ions optical clocks where both the stability and accuracy of the clocks are greatly improved. In the proposed scheme, two Al$^+$ ions traps are utilized. The first trap is used to trap a large number of Al$^+$ ions to improve the stability of the clock laser, while the second trap is used to trap a single Al$^+$ ions to provide the ultimate accuracy. Both traps are cooled with a continuous wave 167 nm laser. The expected clock laser stability can reach $9.0\\times10^{-17}/\\sqrt{\\tau}$. For the second trap, in addition to 167 nm laser Doppler cooling, a second stage pulsed ...

  13. Hybrid ion chains inside an optical cavity

    Science.gov (United States)

    Zhou, Zichao; Siverns, James; Quraishi, Qudsia

    2016-05-01

    Trapped ions remain a leading candidate for the implementation of large-scale quantum networks. These networks require nodes that can store and process quantum information as well as communicate with each other though photonic flying qubits. We propose to use hybrid ion chains of barium, for communication, and ytterbium, for quantum information processing. We report on progress in setting up a hybrid ion chain in a versatile four-blade trap using high numerical aperture collection optics. Although the visible photons produced from barium ions are more favorable as they are not suitable for long distance fiber communication. With this in mind, we intend to implement frequency conversion to overcome this issue. Also, with the view toward increasing the flying-qubit production rate, we propose a cavity-based system to enhance interactions between the ions and photons. The cavity axis is to be placed along the axial direction of the trap allowing a chain of multiple ions to interact with the cavity at the same time. With this configuration the atom-photon coupling strength can be improved by sqrt(N), where N is the number of ions. Experiments will focus on exploring the dynamics of hybrid ion chain, dual species quantum information processing, two-colour entanglement and phase gates assisted by the ion-cavity coupling are to be explored.

  14. Radium single-ion optical clock

    NARCIS (Netherlands)

    Versolato, O. O.; Wansbeek, L. W.; Jungmann, K.; Timmermans, R. G. E.; Willmann, L.; Wilschut, H. W.

    2011-01-01

    We explore the potential of the electric quadrupole transitions $7s\\,^2S_{1/2}$ - $6d\\,^2D_{3/2}$, $6d\\,^2D_{5/2}$ in radium isotopes as single-ion optical frequency standards. The frequency shifts of the clock transitions due to external fields and the corresponding uncertainties are calculated.

  15. Integrated Diffractive Optics for Surface Ion Traps

    Science.gov (United States)

    Streed, Erik; Ghadimi, Moji; Blums, Valdis; Norton, Benjamin; Connor, Paul; Amini, Jason; Volin, Curtis; Lobino, Mirko; Kielpinski, David

    2016-05-01

    Photonic interconnects are a bottleneck to achieving large-scale trapped ion quantum computing. We have modified a Georgia Tech Research Institute microwave chip trap by using e-beam lithography to write reflective diffractive collimating optics (80 μm x 127 μm, f=58.6 μm, λ=369.5nm) on the center electrode. The optics have an NA of 0.55 x 0.73, capturing 13.2% of the solid angle. To evaluate the optics 174Yb+ was loaded by isotope selective photo-ionization from a thermal oven and then shuttled to imaging sites. Near diffraction limited sub-wavelength ion images were obtained with an observed spot sized FWHM of 338 nm x 268 nm vs. a diffraction limit of 336 nm x 257 nm. The total photon collection efficiency was measured to be 5.2+/-1.2%. Coupling into a single mode fiber of up to 2.0+/-0.6% was observed, limited by mismatch in the coupling optics. Image mode quality indicates coupling up to 4% may be possible. Funding from Australian Research Council and IARPA.

  16. All-optical ion generation for ion trap loading

    CERN Document Server

    Sheridan, Kevin; Keller, Matthias; 10.1007/s00340-011-4563-7

    2011-01-01

    We have investigated the all-optical generation of ions by photo-ionisation of atoms generated by pulsed laser ablation. A direct comparison between a resistively heated oven source and pulsed laser ablation is reported. Pulsed laser ablation with 10 ns Nd:YAG laser pulses is shown to produce large calcium flux, corresponding to atomic beams produced with oven temperatures greater than 650 K. For an equivalent atomic flux, pulsed laser ablation is shown to produce a thermal load more than one order of magnitude smaller than the oven source. The atomic beam distributions obey Maxwell-Boltzmann statistics with most probable speeds corresponding to temperatures greater than 2200 K. Below a threshold pulse fluence between 280 mJ/cm^2 and 330 mJ/cm^2, the atomic beam is composed exclusively of ground state atoms. For higher fluences ions and excited atoms are generated.

  17. Time-Dependent Erosion of Ion Optics

    Science.gov (United States)

    Wirz, Richard E.; Anderson, John R.; Katz, Ira; Goebel, Dan M.

    2008-01-01

    The accurate prediction of thruster life requires time-dependent erosion estimates for the ion optics assembly. Such information is critical to end-of-life mechanisms such as electron backstreaming. CEX2D was recently modified to handle time-dependent erosion, double ions, and multiple throttle conditions in a single run. The modified code is called "CEX2D-t". Comparisons of CEX2D-t results with LDT and ELT post-tests results show good agreement for both screen and accel grid erosion including important erosion features such as chamfering of the downstream end of the accel grid and reduced rate of accel grid aperture enlargement with time.

  18. Optical Faraday Cup for Heavy Ion Beams

    Energy Technology Data Exchange (ETDEWEB)

    Bieniosek, Frank; Bieniosek, F.M.; Eylon, S.; Roy, P.K.; Yu, S.S.

    2007-06-25

    We have been using alumina scintillators for imaging beams in heavy-ion beam fusion experiments in 2 to 4 transverse dimensions [1]. The scintillator has a limited lifetime under bombardment by the heavy ion beams. As a possible replacement for the scintillator, we are studying the technique of imaging the beam on a gas cloud. A gas cloud for imaging the beam may be created on a solid hole plate placed in the path of the beam, or by a localized gas jet. It is possible to image the beam using certain fast-quenching optical lines that closely follow beam current density and are independent of gas density. We describe this technique and show preliminary experimental data. This approach has promise to be a new fast beam current diagnostic on a nanosecond time scale.

  19. New directions for ion beam processing of optical materials

    Energy Technology Data Exchange (ETDEWEB)

    White, C.W.; Budai, J.D.; Zhu, J.G.; Withrow, S.P. [Oak Ridge National Lab., TN (United States)

    1997-03-01

    Recent developments in the use of ion implantation to modify the properties of optical materials are summarized. The use of ion implantation to form nanocrystal and quantum dots is emphasized. (author)

  20. Monitoring and Analysis of Two Grid Connected PV Systems

    OpenAIRE

    2013-01-01

    International audience; In this paper, two grid connected photovoltaic systems are studied and monitored for fault detection ad predictive reliability. The first PV grid, is at CNRS-PROMES laboratory in Perpignan, built in 2001 with 3 PV arrays named "Shed","Brise soleil","Mur rideau") connected to the grid thanks to many inverter of different power (3 of 4KWC and 2 of 2.5KWC). The second one is at CNRS-LAAS in Toulouse with a power of 100kWc. It is composed of a facade of 36kWc PV array and ...

  1. A New Three-Dimensional Code for Simulation of Ion Beam Extraction: Ion Optics Simulator

    Institute of Scientific and Technical Information of China (English)

    JIN Dazhi; HUANG Tao; HU Quan; YANG Zhonghai

    2008-01-01

    A new thee-dimensional code, ion optics simulator (IOS), to simulate ion beam extraction is developed in visual C++ language. The theoretical model, the flowchart of code, and the results of calculation as an example are presented.

  2. Efficient Fiber Optic Detection of Trapped Ion Fluorescence

    CERN Document Server

    VanDevender, A P; Amini, J; Leibfried, D; Wineland, D J

    2010-01-01

    Integration of fiber optics may play a critical role in the development of quantum information processors based on trapped ions and atoms by enabling scalable collection and delivery of light and coupling trapped ions to optical microcavities. We trap 24Mg+ ions in a surface-electrode Paul trap that includes an integrated optical fiber for detecting 280-nm fluorescence photons. The collection numerical aperture is 0.37 and total collection efficiency is 2.1 %. The ion can be positioned between 80 \\mum and 100 \\mum from the tip of the fiber by use of an adjustable rf-pseudopotential.

  3. Enhanced Optical Cooling of Ion Beams for LHC

    CERN Document Server

    Bessonov, E G; Mikhailichenko, A A

    2006-01-01

    The possibility of the enhanced optical cooling (EOC) of Lead ions in LHC is investigated. Non-exponential feature of cooling and requirements to the ring lattice, optical and laser systems are discussed. Comparison with optical stochastic cooling (OSC) is represented.

  4. Zero-field optical manipulation of magnetic ions in semiconductors.

    Science.gov (United States)

    Myers, R C; Mikkelsen, M H; Tang, J-M; Gossard, A C; Flatté, M E; Awschalom, D D

    2008-03-01

    Controlling and monitoring individual spins is desirable for building spin-based devices, as well as implementing quantum information processing schemes. As with trapped ions in cold gases, magnetic ions trapped on a semiconductor lattice have uniform properties and relatively long spin lifetimes. Furthermore, diluted magnetic moments in semiconductors can be strongly coupled to the surrounding host, permitting optical or electrical spin manipulation. Here we describe the zero-field optical manipulation of a few hundred manganese ions in a single gallium arsenide quantum well. Optically created mobile electron spins dynamically generate an energy splitting of the ion spins and enable magnetic moment orientation solely by changing either photon helicity or energy. These polarized manganese spins precess in a transverse field, enabling measurements of the spin lifetimes. As the magnetic ion concentration is reduced and the manganese spin lifetime increases, coherent optical control and readout of single manganese spins in gallium arsenide should be possible.

  5. Localization Spectroscopy of a Single Ion in an Optical Lattice

    DEFF Research Database (Denmark)

    Legrand, Olivier Philippe Alexandre

    2015-01-01

    The work reported in this thesis primarily focuses on studies of the dynamics of a single laser-cooled ion, simultaneously confined in the harmonic potential of a linear Paul trap and a rapidly varying periodic potential – a so-called optical lattice – generated from an optical standing-wave. Bes......The work reported in this thesis primarily focuses on studies of the dynamics of a single laser-cooled ion, simultaneously confined in the harmonic potential of a linear Paul trap and a rapidly varying periodic potential – a so-called optical lattice – generated from an optical standing...... calibration and analysis of the detection system, several theoretical simulations of the expected dynamics and associated optical response of the ion were undertaken. Finally, a new laser source based on second harmonic generation was developed in order to perform laser-cooling of Ca+ ions, and to serve...

  6. Radium single-ion optical clock

    CERN Document Server

    Versolato, O O; Jungmann, K; Timmermans, R G E; Willmann, L; Wilschut, H W

    2011-01-01

    We explore the potential of the electric quadrupole transitions $7s\\,^2S_{1/2}$ - $6d\\,^2D_{3/2}$, $6d\\,^2D_{5/2}$ in radium isotopes as single-ion optical frequency standards. The frequency shifts of the clock transitions due to external fields and the corresponding uncertainties are calculated. Several competitive $^A$Ra$^+$ candidates with $A=$ 223 - 229 are identified. In particular, we show that the transition $7s\\,^2S_{1/2}\\,(F=2,m_F=0)$ - $6d\\,^2D_{3/2}\\,(F=0,m_F=0)$ at 828 nm in $^{223}$Ra$^+$, with no linear Zeeman and electric quadrupole shifts, stands out as a relatively simple case, which could be exploited as a compact, robust, and low-cost atomic clock operating at a fractional frequency uncertainty of $10^{-17}$. With more experimental effort, the $^{223,225,226}$Ra$^+$ clocks could be pushed to a projected performance reaching the $10^{-18}$ level.

  7. A novel planar ion funnel design for miniature ion optics

    Science.gov (United States)

    Chaudhary, A.; van Amerom, Friso H. W.; Short, R. T.

    2014-10-01

    The novel planar ion funnel (PIF) design presented in this article emphasizes simple fabrication, assembly, and operation, making it amenable to extreme miniaturization. Simulations performed in SIMION 8.0 indicate that ion focusing can be achieved by using a gradient of electrostatic potentials on concentric metal rings in a plane. A prototype was fabricated on a 35 × 35 mm custom-designed printed circuit board (PCB) with a center hole for ions to pass through and a series of concentric circular metal rings of increasing diameter on the front side of the PCB. Metal vias on the PCB electrically connected each metal ring to a resistive potential divider that was soldered on the back of the PCB. The PIF was tested at 5.5 × 10-6 Torr in a vacuum test setup that was equipped with a broad-beam ion source on the front and a micro channel plate (MCP) ion detector on the back of the PIF. The ion current recorded on the MCP anode during testing indicated a 23× increase in the ion transmission through the PIF when electric potentials were applied to the rings. These preliminary results demonstrate the functionality of a 2D ion funnel design with a much smaller footprint and simpler driving electronics than conventional 3D ion funnels. Future directions to improve the design and a possible micromachining approach to fabrication are discussed in the conclusions.

  8. Computers and the design of ion beam optical systems

    Science.gov (United States)

    White, Nicholas R.

    Advances in microcomputers have made it possible to maintain a library of advanced ion optical programs which can be used on inexpensive computer hardware, which are suitable for the design of a variety of ion beam systems including ion implanters, giving excellent results. This paper describes in outline the steps typically involved in designing a complete ion beam system for materials modification applications. Two computer programs are described which, although based largely on algorithms which have been in use for many years, make possible detailed beam optical calculations using microcomputers, specifically the IBM PC. OPTICIAN is an interactive first-order program for tracing beam envelopes through complex optical systems. SORCERY is a versatile program for solving Laplace's and Poisson's equations by finite difference methods using successive over-relaxation. Ion and electron trajectories can be traced through these potential fields, and plots of beam emittance obtained.

  9. Trapped ions in optical lattices for probing oscillator chain models

    CERN Document Server

    Pruttivarasin, Thaned; Talukdar, Ishan; Kreuter, Axel; Haeffner, Hartmut

    2011-01-01

    We show that a chain of trapped ions embedded in microtraps generated by an optical lattice can be used to study oscillator models related to dry friction and energy transport. Numerical calculations with realistic experimental parameters demonstrate that both static and dynamic properties of the ion chain change significantly as the optical lattice power is varied. Finally, we lay out an experimental scheme to use the spin degree of freedom to probe the phase space structure and quantum critical behavior of the ion chain.

  10. Ion source design for industrial applications

    Science.gov (United States)

    Kaufman, H. R.; Robinson, R. S.

    1981-01-01

    The more frequently used design techniques for the components of broad-beam electron bombardment ion sources are discussed. The approach used emphasizes refractory metal cathodes and permanent-magnet multipole discharge chambers. Design procedures and sample calculations are given for the discharge chamber, ion optics, the cathodes, and the magnetic circuit. Hardware designs are included for the isolator, cathode supports, anode supports, pole-piece assembly, and ion-optics supports. A comparison is made between two-grid and three-grid optics. The designs presented are representative of current technology and are adaptable to a wide range of configurations.

  11. Ion source design for industrial applications

    Science.gov (United States)

    Kaufman, H. R.; Robinson, R. S.

    1981-01-01

    The more frequently used design techniques for the components of broad-beam electron bombardment ion sources are discussed. The approach used emphasizes refractory metal cathodes and permanent-magnet multipole discharge chambers. Design procedures and sample calculations are given for the discharge chamber, ion optics, the cathodes, and the magnetic circuit. Hardware designs are included for the isolator, cathode supports, anode supports, pole-piece assembly, and ion-optics supports. A comparison is made between two-grid and three-grid optics. The designs presented are representative of current technology and are adaptable to a wide range of configurations.

  12. Integrated optics architecture for trapped-ion quantum information processing

    Science.gov (United States)

    Kielpinski, D.; Volin, C.; Streed, E. W.; Lenzini, F.; Lobino, M.

    2016-12-01

    Standard schemes for trapped-ion quantum information processing (QIP) involve the manipulation of ions in a large array of interconnected trapping potentials. The basic set of QIP operations, including state initialization, universal quantum logic, and state detection, is routinely executed within a single array site by means of optical operations, including various laser excitations as well as the collection of ion fluorescence. Transport of ions between array sites is also routinely carried out in microfabricated trap arrays. However, it is still not possible to perform optical operations in parallel across all array sites. The lack of this capability is one of the major obstacles to scalable trapped-ion QIP and presently limits exploitation of current microfabricated trap technology. Here we present an architecture for scalable integration of optical operations in trapped-ion QIP. We show theoretically that diffractive mirrors, monolithically fabricated on the trap array, can efficiently couple light between trap array sites and optical waveguide arrays. Integrated optical circuits constructed from these waveguides can be used for sequencing of laser excitation and fluorescence collection. Our scalable architecture supports all standard QIP operations, as well as photon-mediated entanglement channels, while offering substantial performance improvements over current techniques.

  13. Ion Optics of the HESR storage ring at FAIR for operation with heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Kovalenko, Oleksandr; Dolinskyy, Oleksiy; Litvinov, Yuri; Stoehlker, Thomas [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, Darmstadt (Germany)

    2014-07-01

    High Energy Storage Ring (HESR) of the FAIR project is primarily designed for internal target experiments with stored and cooled antiprotons, which is the main objective of the PANDA collaboration. However, the HESR storage ring also appears to have remarkable properties to carry out physics experiments with heavy ions. This paper proposes a new ion optical design allowing for the heavy ion operation mode of the HESR. The main goal was to provide an optics which meets the requirements of the future experiments with heavy ion beams. In connection, issues like closed orbit correction, dynamic aperture as well as other characteristics of beam dynamics of the new ion optical setup are under analysis in this study.

  14. Nanoengineering ion channels for optical control.

    Science.gov (United States)

    Gorostiza, Pau; Isacoff, Ehud Y

    2008-10-01

    Chemical modification with photoisomerizable tethered ligands endows proteins with sensitivity to light. These optically actuated proteins are revolutionizing research in biology by making it possible to manipulate biological processes noninvasively and with unprecedented spatiotemporal resolution.

  15. Surface modeling for optical fabrication with linear ion source

    CERN Document Server

    Wu, Lixiang; Shao, Jianda

    2016-01-01

    We present a concept of surface decomposition extended from double Fourier series to nonnegative sinusoidal wave surfaces, on the basis of which linear ion sources apply to the ultra-precision fabrication of complex surfaces and diffractive optics. It is the first time that we have a surface descriptor for building a relationship between the fabrication process of optical surfaces and the surface characterization based on PSD analysis, which akin to Zernike polynomials used for mapping the relationship between surface errors and Seidel aberrations. Also, we demonstrate that the one-dimensional scanning of linear ion source is applicable to the removal of surface errors caused by small-tool polishing in raster scan mode as well as the fabrication of beam sampling grating of high diffractive uniformity without a post-processing procedure. The simulation results show that, in theory, optical fabrication with linear ion source is feasible and even of higher output efficiency compared with the conventional approac...

  16. Modification of the ion-optics code GIOS89

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, C.L.; Davids, C.N.

    1995-08-01

    The general ion-optics code GIOS is a very powerful and useful program for calculating the ion optics of an electromagnetic system. It was used extensively in the design and operation of the Fragment Mass Analyzer (FMA). In the original version of the program a feature is described which allows the initial beam density to be varied with angle, energy, mass, or position. In fact, this feature was never implemented, and only isotropic beam densities are available. In order to make more reliable calculations of reaction yields and FMA transport efficiencies, it is important to be able to use more realistic beam density distributions.

  17. Effect of ion-assisted deposition on optical properties of thin films

    Science.gov (United States)

    Tang, Xuefei; Fan, Zhengxiu

    1990-12-01

    Effects of ion assisted deposition on the propertes of Ti02, Zr02 and 5102 optical coatings were investigated. Substrates were bombarded with different ions--- oxygen ions , argon ions , and the mixture ions of oxygen-argon during deposition. The refractive indices, optical absorptions and laser-induced damage thresholds (LIDT) measurments of these films are reported.

  18. Optical cavity integrated surface ion trap for enhanced light collection

    Science.gov (United States)

    Benito, Francisco M.

    Ion trap systems allow the faithful storage and manipulation of qubits encoded in the energy levels of the ions, and can be interfaced with photonic qubits that can be transmitted to connect remote quantum systems. Single photons transmitted from two remote sites, each entangled with one quantum memory, can be used to entangle distant quantum memories by interfering on a beam splitter. Efficient remote entanglement generation relies upon efficient light collection from single ions into a single mode fiber. This can be realized by integrating an ion trap with an optical cavity and employing the Purcell effect for enhancing the light collection. Remote entanglement can be used as a resource for a quantum repeater for provably secure long-distance communication or as a method for communicating within a distributed quantum information processor. We present the integration of a 1 mm optical cavity with a micro-fabricated surface ion trap. The plano-concave cavity is oriented normal to the chip surface where the planar mirror is attached underneath the trap chip. The cavity is locked using a 780 nm laser which is stabilized to Rubidium and shifted to match the 369 nm Doppler transition in Ytterbium. The linear ion trap allows ions to be shuttled in and out of the cavity mode. The Purcell enhancement of spontaneous emission into the cavity mode would then allow efficient collection of the emitted photons, enabling faster remote entanglement generation.

  19. Reactive ion beam figuring of optical aluminium surfaces

    Science.gov (United States)

    Bauer, Jens; Frost, Frank; Arnold, Thomas

    2017-03-01

    Ultra-smooth and arbitrarily shaped reflective optics are necessary for further progress in EUV/XUV lithography, x-ray and synchrotron technology. As one of the most important technological mirror optic materials, aluminium behaves in a rather difficult way in ultra-precision machining with such standard techniques as diamond-turning and subsequent ion beam figuring (IBF). In particular, in the latter, a strong surface roughening is obtained. Hence, up to now it has not been possible to attain the surface qualities required for UV or just visible spectral range applications. To overcome the limitations mainly caused by the aluminium alloy structural and compositional conditions, a reactive ion beam machining process using oxygen process gas is evaluated. To clarify the principle differences in the effect of oxygen gas contrary to oxygen ions on aluminium surface machining, we firstly focus on chemical-assisted ion beam etching (CAIBE) and reactive ion beam etching (RIBE) experiments in a phenomenological manner. Then, the optimum process route will be explored within a more quantitative analysis applying the concept of power spectral density (PSD) for a sophisticated treatment of the surface topography. Eventually, the surface composition is examined by means of dynamic secondary ion mass spectrometry (SIMS) suggesting a characteristic model scheme for the chemical modification of the aluminium surface during oxygen ion beam machining. Monte Carlo simulations were applied to achieve a more detailed process conception.

  20. Hyperfine and Optical Barium Ion Qubits

    CERN Document Server

    Dietrich, M R; Noel, T; Shu, G; Blinov, B B

    2010-01-01

    State preparation, qubit rotation, and high fidelity readout are demonstrated for two separate \\baseven qubit types. First, an optical qubit on the narrow 6S$_{1/2}$ to 5D$_{5/2}$ transition at 1.76 $\\mu$m is implemented. Then, leveraging the techniques developed there for readout, a ground state hyperfine qubit using the magnetically insensitive transition at 8 GHz is accomplished.

  1. Beam optics of the folded tandem ion accelerator at BARC

    Indian Academy of Sciences (India)

    S Santra; P Singh

    2002-07-01

    The beam optics of the 6 MV folded tandem ion accelerator, that has recently been commissioned at Bhabha Atomic Research Centre, Mumbai, is presented. Typical beam trajectories for proton and 12C beams under different conditions, are shown. The constraints on the design due to the use of the infrastructure of the Van de Graaff accelerator, which existed earlier, are discussed.

  2. Pinning an Ion with an Intracavity Optical Lattice

    DEFF Research Database (Denmark)

    Linnet, Rasmus Bogh; Leroux, Ian Daniel; Marciante, Mathieu

    2012-01-01

    We report one-dimensional pinning of a single ion by an optical lattice. A standing-wave cavity produces the lattice potential along the rf-field-free axis of a linear Paul trap. The ion’s localization is detected by measuring its fluorescence when excited by standing-wave fields with the same...

  3. Special diffractive elements for optical trapping fabricated on optical fiber tips using the focused ion beam

    Science.gov (United States)

    Rodrigues Ribeiro, R. S.; Guerreiro, A.; Viegas, J.; Jorge, P. A. S.

    2016-05-01

    In this work, spiral phase lenses and Fresnel zone lenses for beam tailoring, fabricated on the tip of optical fibers, are reported. The spiral phase lenses allow tailoring the fundamental guided mode, a Gaussian beam, into a Laguerre - Gaussian profile without using additional optical elements. Whereas, the Fresnel lenses are used as focusing systems. The lenses are fabricated using Focused Ion Beam milling, enabling high resolution in the manufacturing process. The output optical intensity profiles matching the numerical simulations are presented and analyzed.

  4. Dual Ion Beam Deposition Of Diamond Films On Optical Elements

    Science.gov (United States)

    Deutchman, Arnold H.; Partyka, Robert J.; Lewis, J. C.

    1990-01-01

    Diamond film deposition processes are of great interest because of their potential use for the formation of both protective as well as anti-reflective coatings on the surfaces of optical elements. Conventional plasma-assisted chemical vapor deposition diamond coating processes are not ideal for use on optical components because of the high processing temperatures required, and difficulties faced in nucleating films on most optical substrate materials. A unique dual ion beam deposition technique has been developed which now makes possible deposition of diamond films on a wide variety of optical elements. The new DIOND process operates at temperatures below 150 aegrees Farenheit, and has been used to nucleate and grow both diamondlike carbon and diamond films on a wide variety of optical :taterials including borosilicate glass, quartz glass, plastic, ZnS, ZnSe, Si, and Ge.

  5. Improved ion optics for introduction of ions into a 9.4-T Fourier transform ion cyclotron resonance mass spectrometer.

    Science.gov (United States)

    Chen, Yu; Leach, Franklin E; Kaiser, Nathan K; Dang, Xibei; Ibrahim, Yehia M; Norheim, Randolph V; Anderson, Gordon A; Smith, Richard D; Marshall, Alan G

    2015-01-01

    Enhancements to the ion source and transfer optics of our 9.4 T Fourier transform ion cyclotron resonance (ICR) mass spectrometer have resulted in improved ion transmission efficiency for more sensitive mass measurement of complex mixtures at the MS and MS/MS levels. The tube lens/skimmer has been replaced by a dual ion funnel and the following octopole by a quadrupole for reduced ion cloud radial expansion before transmission into a mass-selective quadrupole. The number of ions that reach the ICR cell is increased by an order of magnitude for the funnel/quadrupole relative to the tube lens/skimmer/octopole. Copyright © 2015 John Wiley & Sons, Ltd.

  6. Ion Beam Assisted Deposition Of Optical Thin Films - Recent Results

    Science.gov (United States)

    McNally, J. J.; Al-Jumaily, G. A.; Wilson, S. R.; McNeil, J. R.

    1985-11-01

    We have examined the properties of dielectric (Ti02, Si02, -Al203, Ta205 and Hf02) films deposited using ion-assisted deposition (IAD). The films were characterized using an angularly resolved scatterometer, spectrophotometer and Raman spectroscopy. A reduction in optical scatter, especially that due to low spatial frequencies, is observed for films deposited with simultaneous ion bombardment. Higher values of refractive index are obtained for films deposited using IAD. Raman spectra indicate a crystalline phase change in TiO2 films is induced by bombardment of samples with 02 ions during deposition. Other experimental data and the effects of the induced phase transition on the optical properties of TiO2 will be discussed.

  7. Ion beam induced optical and surface modification in plasmonic nanostructures

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Udai B., E-mail: udaibhansingh123@gmail.com; Gautam, Subodh K.; Kumar, Sunil; Hooda, Sonu; Ojha, Sunil; Singh, Fouran

    2016-07-15

    In present work, ion irradiation induced nanostructuring has been exploited as an efficient and effective tool for synthesis of coupled plasmonics nanostructures by using 1.2 MeV Xe ions on Au/ZnO/Au system deposited on glass substrate. The results are correlated on the basis of their optical absorption, surface morphologies and enhanced sensitivity of evolved phonon modes by using UV Visible spectroscopy, scanning electron microscopy (SEM), and Raman spectroscopy (RS), respectively. Optical absorbance spectra of plasmonic nanostructures (NSs) show a decrease in band gap, which may be ascribed to the formation of defects with ion irradiation. The surface morphology reveals the formation of percolated NSs upon ion irradiation and Rutherford backscattering spectrometry (RBS) study clearly shows the formation of multilayer system. Furthermore, RS measurements on samples are studied to understand the enhanced sensitivity of ion irradiation induced phonon mode at 573 cm{sup −1} along with other modes. As compared to pristine sample, a stronger and pronounced evolution of these phonon modes is observed with further ion irradiation, which indicates localized surface plasmon results with enhanced intensity of phonon modes of Zinc oxide (ZnO) material. Thus, such plasmonic NSs can be used as surface enhanced Raman scattering (SERS) substrates.

  8. The Gridless Plasma Ion Source(GIS)for Plasma Ion Assisted Optical Coating

    Institute of Scientific and Technical Information of China (English)

    尤大伟; 李晓谦; 王宇; 林永昌

    2004-01-01

    High-quality optical coating is a key technology for modern optics. Ion-assisted deposition technology was used to improve the vaporized coating in 1980's. The GIS (gridless ion source), which is an advanced plasma source for producing a high-quality optical coating in large area, can produce a large area uniformity>1000 mm(diameter), a high ion current density ~ 0.5mA/cm2, 20 eV ~ 200 eV energetic plasma ions and can activate reactive gas and film atoms. Now we have developed a GIS system. The GIS and the plasma ion-assisted deposition technology are investigated to achieve a high-quality optical coating. The GIS is a high power and high current source with a power of I kW ~ 7.5 kW, a current of 10 A ~ 70 A and an ion density of 200μA/cm2 ~ 500μA/cm2. Because of the special magnetic structure, the plasma-ion extraction efficiency has been improved to obtain a maximum ion density of 500μA/cm2 in the medium power (~ 4 kW) level. The GIS applied is of a special cathode structure, so that the GIS operation can be maintained under a rather low power and the lifetime of cathode will be extended. The GIS has been installed in the LPSX-1200 type box coating system. The coated TiO2, SiO2 films such as antireflective films with the system have the same performance reported by Leybold Co, 1992, along with a controllable refractive index and film structure.

  9. Ion assisted deposition with low-energy ions for applications in modern optics

    CERN Document Server

    Kennedy, M

    1999-01-01

    realised by a process adaptation with UV-absorbing films. A further focal point are antireflective coatings on alkali halides optics for high-power CO sub 2 -lasers. Ion assisted deposition of NaF-films at extremely low ion energies (E sub i sub o sub n approx 5 eV) qualifies antireflective coatings with minimal absorption (alpha approx 1.5 cm sup - sup 1), high short-pulse damage threshold (50%-LIDT approx 60J/cm sup 2) and improved degradational stability. Main objective of this work is the development of ion assisted deposition processes without additional substrate heating for applications in precision and laser optics. New low-energy ion sources with ion energies below 100 eV were employed for the research work. Starting point of the process development are basic investigations on the ion assisted evaporation of fluoride and oxide thin film materials. The optimisation of the coating processes is primary done with the help of optical characterisation methods (spectral photometry, laser calorimetry, measur...

  10. INJECTION OPTICS FOR THE JLEIC ION COLLIDER RING

    Energy Technology Data Exchange (ETDEWEB)

    Morozov, Vasiliy [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Derbenev, Yaroslav [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Lin, Fanglei [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Pilat, Fulvia C. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Wei, Guohio [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Zhang, Yuhong [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Nosochkov, Y. M. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Cai, Yunhai [SLAC National Accelerator Lab., Menlo Park, CA (United States); Sullivan, Michael K. [SLAC National Accelerator Lab., Menlo Park, CA (United States); Wang, M. H. [SLAC National Accelerator Lab., Menlo Park, CA (United States)

    2016-05-01

    The Jefferson Lab Electron-Ion Collider (JLEIC) will accelerate protons and ions from 8 GeV to 100 GeV. A very low beta function at the Interaction Point (IP) is needed to achieve the required luminosity. One consequence of the low beta optics is that the beta function in the final focusing (FF) quadrupoles is extremely high. This leads to a large beam size in these magnets as well as strong sensitivity to errors which limits the dynamic aperture. These effects are stronger at injection energy where the beam size is maximum, and therefore very large aperture FF magnets are required to allow a large dynamic aperture. A standard solution is a relaxed injection optics with IP beta function large enough to provide a reasonable FF aperture. This also reduces the effects of FF errors resulting in a larger dynamic aperture at injection. We describe the ion ring injection optics design as well as a beta-squeeze transition from the injection to collision optics.

  11. Ion optical design of a collinear laser-negative ion beam apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Diehl, C.; Wendt, K. [Institut fuer Physik, Johannes Gutenberg-Universitaet, Mainz, D-55099 Mainz (Germany); Lindahl, A. O.; Andersson, P.; Hanstorp, D. [Department of Physics, University of Gothenburg, SE-412 96 Goeteborg (Sweden)

    2011-05-15

    An apparatus for photodetachment studies on atomic and molecular negative ions of medium up to heavy mass (M {approx_equal} 500) has been designed and constructed. Laser and ion beams are merged in the apparatus in a collinear geometry and atoms, neutral molecules and negative ions are detected in the forward direction. The ion optical design and the components used to optimize the mass resolution and the transmission through the extended field-free interaction region are described. A 90 deg. sector field magnet with 50 cm bending radius in combination with two slits is used for mass dispersion providing a resolution of M/{Delta}M congruent with 800 for molecular ions and M/{Delta}M congruent with 400 for atomic ions. The difference in mass resolution for atomic and molecular ions is attributed to different energy distributions of the sputtered ions. With 1 mm slits, transmission from the source through the interaction region to the final ion detector was determined to be about 0.14%.

  12. Ion optical design of a collinear laser-negative ion beam apparatus

    Science.gov (United States)

    Diehl, C.; Wendt, K.; Lindahl, A. O.; Andersson, P.; Hanstorp, D.

    2011-05-01

    An apparatus for photodetachment studies on atomic and molecular negative ions of medium up to heavy mass (M ≃ 500) has been designed and constructed. Laser and ion beams are merged in the apparatus in a collinear geometry and atoms, neutral molecules and negative ions are detected in the forward direction. The ion optical design and the components used to optimize the mass resolution and the transmission through the extended field-free interaction region are described. A 90° sector field magnet with 50 cm bending radius in combination with two slits is used for mass dispersion providing a resolution of M/ΔM≅800 for molecular ions and M/ΔM≅400 for atomic ions. The difference in mass resolution for atomic and molecular ions is attributed to different energy distributions of the sputtered ions. With 1 mm slits, transmission from the source through the interaction region to the final ion detector was determined to be about 0.14%.

  13. Copper ion-exchanged channel waveguides optimization for optical trapping.

    Science.gov (United States)

    Reshak, A H; Khor, K N; Shahimin, M M; Murad, S A Z

    2013-08-01

    Optical trapping of particles has become a powerful non-mechanical and non-destructive technique for precise particle positioning. The manipulation of particles in the evanescent field of a channel waveguide potentially allows for sorting and trapping of several particles and cells simultaneously. Channel waveguide designs can be further optimized to increase evanescent field prior to the fabrication process. This is crucial in order to make sure that the surface intensity is sufficient for optical trapping. Simulation configurations are explained in detail with specific simulation flow. Discussion on parameters optimization; physical geometry, optical polarization and wavelength is included in this paper. The effect of physical, optical parameters and beam spot size on evanescent field has been thoroughly discussed. These studies will continue toward the development of a novel copper ion-exchanged waveguide as a method of particle sorting, with biological cell propulsion studies presently underway.

  14. Optical properties of lead borate glasses containing Dy3+ ions

    Science.gov (United States)

    Pisarska, Joanna

    2009-07-01

    Optical properties of lead borate glasses containing Dy3+ ions were examined using absorption and luminescence measurements and theoretical calculations based on the Judd-Ofelt framework and the Inokuti-Hirayama model. The luminescence spectra show two characteristic bands at 480 and 573 nm, which are due to 4F9/2-6H15/2 (blue) and 4F9/2-6H13/2 (yellow) transitions of trivalent Dy3+ ions. The yellow/blue luminescence and its decay were analyzed as a function of activator concentration.

  15. Optically induced structural phase transitions in ion Coulomb crystals

    DEFF Research Database (Denmark)

    Horak, Peter; Dantan, Aurelien Romain; Drewsen, Michael

    2012-01-01

    , such as body-centered cubic and face-centered cubic, can be suppressed by a proper choice of the potential depth and periodicity. Furthermore, by varying the harmonic trap parameters and/or the optical potential in time, controlled transitions between crystal structures can be obtained with close to unit......We investigate numerically the structural dynamics of ion Coulomb crystals confined in a three-dimensional harmonic trap when influenced by an additional one-dimensional optically induced periodical potential. We demonstrate that transitions between thermally excited crystal structures...

  16. Precision measurement of electronic ion-ion interactions between neighboring Eu3+ optical centers.

    Science.gov (United States)

    Ahlefeldt, R L; McAuslan, D L; Longdell, J J; Manson, N B; Sellars, M J

    2013-12-13

    We report measurements of discrete excitation-induced frequency shifts on the 7F0→5D0 transition of the Eu+ center in La:Lu:EuCl3·6D2O resulting from the optical excitation of neighboring Eu3+ ions. Shifts of up to 46.081±0.005  MHz were observed. The magnitude of the interaction between neighboring ions was found to be significantly larger than expected from the electric dipole-dipole mechanism often observed in rare earth systems. We show that a large network of interacting and individually addressable centers can be created by lightly doping crystals otherwise stoichiometric in the optically active rare earth ion, and that this network could be used to implement a quantum processor with more than ten qubits.

  17. Coherent optical ultrasound detection with rare-earth ion dopants

    CERN Document Server

    Tay, Jian Wei; Longdell, Jevon

    2010-01-01

    We describe theoretical and experimental demonstration for optical detection of ultrasound using a spectral hole engraved in cryogenically cooled rare-earth ion doped solids. Our method utilizes the dispersion effects due to the spectral hole to perform phase to amplitude modulation conversion. Like previous approaches using spectral holes it has the advantage of detection with large \\'etendue. The method also has the benefit that high sensitivity can be obtained with moderate absorption contrast for the spectral holes.

  18. Optical attenuation in ion-implanted silicon waveguide racetrack resonators.

    Science.gov (United States)

    Doylend, J K; Jessop, P E; Knights, A P

    2011-08-01

    The optical absorption at wavelengths near 1550 nm has been quantified as a function of annealing temperature in ion-implanted silicon-on-insulator racetrack resonators. The variation of the output characteristics of the bus waveguide versus the concentration of implantation-induced lattice disorder in the ring is used to develop a novel method for the determination of the coupling and round-trip loss of the resonator, independently. This experimental procedure has general applicability for the determination of these parameters. Significant propagation loss is found to persist following annealing at temperatures previously observed to remove the majority of ion implantation damage. It is suggested that these annealing characteristics are a consequence of an ion implantation range which is greater than the silicon waveguide layer thickness.

  19. Systematic Shifts for Ytterbium-ion Optical Frequency Standards

    CERN Document Server

    Batra, N; Gupta, A Sen; Singh, Sukhjit; Arora, Amisha; Arora, Bindiya

    2014-01-01

    The projected systematic uncertainties of single trapped Ytterbium-ion optical frequency standards are estimated for the quadrupole and octupole transitions which are at wavelengths 435.5 nm and 467 nm, respectively. Finite temperature of the ion and its interaction with the external fields introduce drift in the measured frequency compared to its absolute value. Frequency shifts due to electric quadrupole moment, induced polarization and excess micromotion of the ion depend on electric fields, which are estimated in this article. Geometry of the trap electrodes also result in unwanted electric fields which have been considered in our calculation. Magnetic field induced shift and Stark shifts due to electro-magnetic radiation at a surrounding temperature are also estimated. At CSIR-NPL, we are developing a frequency standard based on the octupole transition for which the systematic uncertainties are an order of magnitude smaller than that using the quadrupole transition, as described here.

  20. A TWO-GRID METHOD FOR THE STEADY PENALIZED NAVIER-STOKES EQUATIONS

    Institute of Scientific and Technical Information of China (English)

    Chun-fengRen; Yi-chenMa

    2004-01-01

    A two-grid method for the steady penalized incompressible Navier-Stokes equations is presented. Convergence results are proved. If h = O(H3-s) and ε = O(H5-2s) (s = 0(n=2);s=1/2(n=3)are chosen, the convergence order of this two-grid method is the same as that of the usual finite element method. Numerical results show that this method is efficient and can save a lot of computation time.

  1. Stitching algorithm for ion beam figuring of optical mirrors

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    A novel stitching machining method for ion beam figuring of optical mirrors is presented in this paper. Problems that should be dealt with in the stitching process such as shaping principle,algorithm for dwell time calculation,parameter identification and compensation for positioning errors are discussed. Based on Computer Controlled Optical Surfacing(CCOS)principle,the finite field nonlinear model is deduced from the stitching shaping mechanism;with the superposition property in the model,a modified Richardson-Lucy iterative algorithm is presented to deconvolute the dwell time for the stitching process;the effect of the positioning errors and the removal rate on the machining accuracy and shape is modeled and then the identification and compensation algorithm for these parameters is proposed based on this model.With these studies,shaping theory and algorithm are constructed,and then the stitching process for ion beam figuring comes into being.Figuring experiments are made on planar samples;the process convergence ratio is 10,which is similar to that in full aperture figuring.Theo- retical and experimental studies indicate that the stitching theory and algorithm in the ion beam figuring process presented in this paper are a novel method for fabrication of precision mirrors with lower cost.

  2. Optics measurement and correction for the Relativistic Heavy Ion Collider

    Science.gov (United States)

    Shen, Xiaozhe

    The quality of beam optics is of great importance for the performance of a high energy accelerator like the Relativistic Heavy Ion Collider (RHIC). The turn-by-turn (TBT) beam position monitor (BPM) data can be used to derive beam optics. However, the accuracy of the derived beam optics is often limited by the performance and imperfections of instruments as well as measurement methods and conditions. Therefore, a robust and model-independent data analysis method is highly desired to extract noise-free information from TBT BPM data. As a robust signal-processing technique, an independent component analysis (ICA) algorithm called second order blind identification (SOBI) has been proven to be particularly efficient in extracting physical beam signals from TBT BPM data even in the presence of instrument's noise and error. We applied the SOBI ICA algorithm to RHIC during the 2013 polarized proton operation to extract accurate linear optics from TBT BPM data of AC dipole driven coherent beam oscillation. From the same data, a first systematic estimation of RHIC BPM noise performance was also obtained by the SOBI ICA algorithm, and showed a good agreement with the RHIC BPM configurations. Based on the accurate linear optics measurement, a beta-beat response matrix correction method and a scheme of using horizontal closed orbit bumps at sextupoles for arc beta-beat correction were successfully applied to reach a record-low beam optics error at RHIC. This thesis presents principles of the SOBI ICA algorithm and theory as well as experimental results of optics measurement and correction at RHIC.

  3. Optical studies of ion-beam synthesized metal alloy nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Magudapathy, P., E-mail: pmp@igcar.gov.in; Srivatsava, S. K.; Gangopadhyay, P.; Amirthapandian, S.; Sairam, T. N.; Panigrahi, B. K. [Materials Physics Division, Indira Gandhi Centre for Atomic Research, Kalpakkam – 603 102 India (India)

    2015-06-24

    Au{sub x}Ag{sub 1-x} alloy nanoparticles with tunable surface plasmon resonance (SPR) have been synthesized on a silica glass substrate. A small Au foil on an Ag foil is irradiated as target substrates such that ion beam falls on both Ag foil and Au foils. Silica slides are kept at an angle ∼45° with respect to the metallic foils. While irradiating the metallic foils with 100 keV Ar{sup +} ions, sputtered Au and Ag atoms get deposited on the silica-glass. In this configuration the foils have been irradiated by Ar{sup +} ions to various fluences at room temperature and the sputtered species are collected on silica slides. Formation of Au{sub x}Ag{sub 1-x} nanoparticles has been confirmed from the optical absorption measurements. With respect to the exposure area of Au and Ag foils to the ion beam, the SPR peak position varies from 450 to 500 nm. Green photoluminescence has been observed from these alloy metal nanoparticles.

  4. Optical fiber sensors fabricated by the focused ion beam technique

    DEFF Research Database (Denmark)

    Yuan, Scott Wu; Wang, Fei; Bang, Ole

    2012-01-01

    crystal fiber (PCF). Using this technique we fabricate a highly compact fiber-optic Fabry-Pérot (FP) refractive index sensor near the tip of fiber taper, and a highly sensitive in-line temperature sensor in PCF. We also demonstrate the potential of using FIB to selectively fill functional fluid......Focused ion beam (FIB) is a highly versatile technique which helps to enable next generation of lab-on-fiber sensor technologies. In this paper, we demonstrate the use application of FIB to precisely mill the fiber taper and end facet of both conventional single mode fiber (SMF) and photonic...

  5. TWO-GRID DISCRETIZATION SCHEMES OF THE NONCONFORMING FEM FOR EIGENVALUE PROBLEMS

    Institute of Scientific and Technical Information of China (English)

    Yidu Yang

    2009-01-01

    This paper extends the two-grid discretization scheme of the conforming finite elements proposed by Xu and Zhou (Math. Comput., 70 (2001), pp.17-25) to the nonconforming finite elements for eigenvalue problems. In particular, two two-grid discretization schemes based on Rayleigh quotient technique are proposed. By using these new schemes, the solution of an eigenvalue problem on a fine mesh is reduced to that on a much coarser mesh together with the solution of a linear algebraic system on the fine mesh. The resulting solution still maintains an asymptotically optimal accuracy. Comparing with the two-grid discretization scheme of the conforming finite elements, the main advantages of our new schemes are twofold when the mesh size is small enough. First, the lower bounds of the exact eigenvalues in our two-grid discretization schemes can be obtained. Second, the first eigenvalue given by the new schemes has much better accuracy than that obtained by solving the eigenvalue problems on the fine mesh directly.

  6. Domed, 40-cm-Diameter Ion Optics for an Ion Thruster

    Science.gov (United States)

    Soulas, George C.; Haag, Thomas W.; Patterson, Michael J.

    2006-01-01

    deflections of the grids. A secondary reason for choosing molybdenum is the availability of a large database for this material. To keep development costs low, the NEXT grids have been fabricated by the same techniques used to fabricate the NSTAR grids. In tests, the NEXT ion optics have been found to outperform the NSTAR ion optics, as expected.

  7. Integration of fluorescence collection optics with a microfabricated surface electrode ion trap

    CERN Document Server

    Brady, Gregory R; Moehring, David L; Stick, Daniel; Highstrete, Clark; Fortier, Kevin M; Blain, Matthew G; Haltli, Raymond A; Cruz-Cabrera, Alvaro A; Briggs, Ronald D; Wendt, Joel R; Carter, Tony R; Samora, Sally; Kemme, Shanalyn A

    2010-01-01

    We have successfully demonstrated an integrated optical system for collecting the fluorescence from a trapped ion. The system, consisting of an array of transmissive, dielectric micro-optics and an optical fiber array, has been intimately incorporated into the ion trapping chip without negatively impacting trapping performance. Considerations such as our choice of epoxies, vacuum feedthrough, and optical component materials did not degrade the vacuum environment, and we have demonstrated light detection as well as ion trapping and shuttling behavior comparable to trapping chips without integrated optics, with no modification to the control voltages of the trapping chip.

  8. Optical fiber tip templating using direct focused ion beam milling.

    Science.gov (United States)

    Micco, A; Ricciardi, A; Pisco, M; La Ferrara, V; Cusano, A

    2015-11-04

    We report on a method for integrating sub-wavelength resonant structures on top of optical fiber tip. Our fabrication technique is based on direct milling of the glass on the fiber facet by means of focused ion beam. The patterned fiber tip acts as a structured template for successive depositions of any responsive or functional overlay. The proposed method is validated by depositing on the patterned fiber a high refractive index material layer, to obtain a 'double-layer' photonic crystal slab supporting guided resonances, appearing as peaks in the reflection spectrum. Morphological and optical characterizations are performed to investigate the effects of the fabrication process. Our results show how undesired effects, intrinsic to the fabrication procedure should be taken into account in order to guarantee a successful development of the device. Moreover, to demonstrate the flexibility of our approach and the possibility to engineering the resonances, a thin layer of gold is also deposited on the fiber tip, giving rise to a hybrid photonic-plasmonic structure with a complementary spectral response and different optical field distribution at the resonant wavelengths. Overall, this work represents a significant step forward the consolidation of Lab-on-Fiber Technology.

  9. Optical properties of Yb ions in GaN epilayer

    Science.gov (United States)

    Jadwisienczak, W. M.; Lozykowski, H. J.

    2003-07-01

    In recent years, an important effort in semiconductor materials research has been devoted to III-nitrides semiconductors doped with rare earth ions due to the high potential of these materials in light-emitting device applications. Ytterbium (Yb 3+) is one of a few lanthanide ions which have not been investigated as an optically active center in these materials yet. In this paper we report the observation of luminescence from GaN films grown on sapphire (0 0 0 1) substrate by metal organic chemical vapor deposition and doped by implantation with Yb 3+ ions. The high resolution photo- and cathodoluminescence spectra of GaN:Yb 3+ were studied at different excitation conditions in temperatures ranging from 8 to 330 K and revealed weak thermal quenching. The luminescence emission lines are assigned to transitions between the spin-orbit levels 2F 5/2 → 2F 7/2 of Yb 3+ (4f 13). The analysis of the Yb luminescence spectra allowed us to suggest the energy level diagram of the crystal-field-split 4f 13 levels for the Yb ion center. The most probable lattice location of Yb in GaN is the substitutional Ga site. Furthermore, the luminescence kinetics of internal transitions of Yb 3+ incorporated in GaN was investigated by means of decay and time-resolved luminescence measurements. It was found that the ytterbium decay is non-exponential with dominant exponential term of ˜100 μs with little dependence on the ambient temperature. The results indicate that Yb-doped GaN epilayer may be suitable as a material for near infrared optoelectronic devices.

  10. Solving Graph Laplacian Systems Through Recursive Bisections and Two-Grid Preconditioning

    Energy Technology Data Exchange (ETDEWEB)

    Ponce, Colin [Cornell Univ., Ithaca, NY (United States); Vassilevski, Panayot S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-02-18

    We present a parallelizable direct method for computing the solution to graph Laplacian-based linear systems derived from graphs that can be hierarchically bipartitioned with small edge cuts. For a graph of size n with constant-size edge cuts, our method decomposes a graph Laplacian in time O(n log n), and then uses that decomposition to perform a linear solve in time O(n log n). We then use the developed technique to design a preconditioner for graph Laplacians that do not have this property. Finally, we augment this preconditioner with a two-grid method that accounts for much of the preconditioner's weaknesses. We present an analysis of this method, as well as a general theorem for the condition number of a general class of two-grid support graph-based preconditioners. Numerical experiments illustrate the performance of the studied methods.

  11. Amplitude Noise Reduction of Ion Lasers with Optical Feedback

    Science.gov (United States)

    Herring, Gregory C.

    2011-01-01

    A reduction in amplitude noise on the output of a multi-mode continuous-wave Ar-ion laser was previously demonstrated when a fraction of the output power was retroreflected back into the laser cavity. This result was reproduced in the present work and a Fabry-Perot etalon was used to monitor the longitudinal mode structure of the laser. A decrease in the number of operating longitudinal cavity modes was observed simultaneously with the introduction of the optical feedback and the onset of the amplitude noise reduction. The noise reduction is a result of a reduced number of lasing modes, resulting in less mode beating and amplitude fluctuations of the laser output power.

  12. Rapid evaluation of ion thruster lifetime using optical emission spectroscopy

    Science.gov (United States)

    Rock, B. A.; Parsons, M. L.; Mantenieks, M. A.

    1985-01-01

    A major life-limiting phenomenon of electric thrusters is the sputter erosion of discharge chamber components. Thrusters for space propulsion are required to operate for extended periods of time, usually in excess of 10,000 hr. Lengthy and very costly life-tests in high-vacuum facilities have been required in the past to determine the erosion rates of thruster components. Alternative methods for determining erosion rates which can be performed in relatively short periods of time at considerably lower costs are studied. An attempt to relate optical emission intensity from an ion bombarded surface (screen grid) to the sputtering rate of that surface is made. The model used a kinetic steady-state (KSS) approach, balancing the rates of population and depopulation of ten low-lying excited states of the sputtered molybdenum atom (MoI) with those of the ground state to relate the spectral intensities of the various transitions of the MoI to the population densities. Once this is accomplished, the population density can be related to the sputting rate of the target. Radiative and collisional modes of excitation and decay are considered. Since actual data has not been published for MoI excitation rate and decay constants, semiempirical equations are used. The calculated sputtering rate and intensity is compared to the measured intensity and sputtering rates of the 8 and 30 cm ion thrusters.

  13. Multi-slit triode ion optical system with ballistic beam focusing

    Energy Technology Data Exchange (ETDEWEB)

    Davydenko, V., E-mail: V.I.Davydenko@inp.nsk.su; Amirov, V.; Gorbovsky, A.; Deichuli, P.; Ivanov, A.; Kolmogorov, A.; Kapitonov, V.; Mishagin, V.; Shikhovtsev, I.; Sorokin, A.; Stupishin, N. [Budker Institute of Nuclear Physics, Novosibirsk 630090 (Russian Federation); Karpushov, A. N. [Ecole Polytechnique Fédérale de Lausanne, Centre de Recherches en Physique des Plasmas (CRPP), CH-1015 Lausanne (Switzerland); Smirnov, A. [Tri Alpha Energy, Inc., Rancho Santa Margarita, California 92688 (United States); Uhlemann, R. [Institute of Energy and Climate Research-Plasma Physics, Research Center Juelich, 52425 Juelich (Germany)

    2016-02-15

    Multi-slit triode ion-optical systems with spherical electrodes are of interest for formation of intense focused neutral beams for plasma heating. At present, two versions of focusing multi-slit triode ion optical system are developed. The first ion optical system forms the proton beam with 15 keV energy, 140 A current, and 30 ms duration. The second ion optical system is intended for heating neutral beam injector of Tokamak Configuration Variable (TCV). The injector produces focused deuterium neutral beam with 35 keV energy, 1 MW power, and 2 s duration. In the later case, the angular beam divergence of the neutral beam is 20-22 mrad in the direction across the slits of the ion optical system and 12 mrad in the direction along the slits.

  14. Production of polarized negative deuterium ion beam with dual optical pumping in KEK

    Energy Technology Data Exchange (ETDEWEB)

    Kinsho, M.; Ikegami, K.; Takagi, A. [National Lab. for High Energy Physics, Tsukuba, Ibaraki (Japan); Mori, Y.

    1997-02-01

    To obtain highly nuclear-spin vector polarized negative deuterium ion beam, a dual optically pumped polarized negative deuterium ion source has been developed at KEK. It is possible to select a pure nuclear-spin state with this scheme, and negative deuterium ion beam with 100% nuclear-spin vector polarization can be produced in principle. We have obtained about 70% of nuclear-spin vector polarized negative deuterium ion beam so far. This result may open up a new possibilities for the optically pumped polarized ion source. (author)

  15. Ion Deflection for Final Optics In Laser Inertial Fusion Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Abbott, R P; Latkowski, J F

    2006-11-17

    Left unprotected, both transmissive and reflective final optics in a laser inertial fusion power plant would quickly fail from melting, pulsed thermal stresses, or degradation of optical properties as a result of ion implantation. One potential option for mitigating this threat is to magnetically deflect the ions such that they are directed into a robust energy dump. In this paper we detail integrated studies that have been carried out to asses the viability of this approach for protecting final optics.

  16. Two grid iteration with a conjugate gradient fine grid smoother applied to a groundwater flow model

    Energy Technology Data Exchange (ETDEWEB)

    Hagger, M.J.; Spence, A.; Cliffe, K.A.

    1994-12-31

    This talk is concerned with the efficient solution of Ax=b, where A is a large, sparse, symmetric positive definite matrix arising from a standard finite element discretisation of the groundwater flow problem {triangledown}{sm_bullet}(k{triangledown}p)=0. Here k is the coefficient of rock permeability in applications and is highly discontinuous. The discretisation is carried out using the Harwell NAMMU finite element package, using, for 2D, 9 node biquadratic rectangular elements, and 27 node biquadratics for 3D. The aim is to develop a robust technique for iterative solutions of 3D problems based on a regional groundwater flow model of a geological area with sharply varying hydrogeological properties. Numerical experiments with polynomial preconditioned conjugate gradient methods on a 2D groundwater flow model were found to yield very poor results, converging very slowly. In order to utilise the fact that A comes from the discretisation of a PDE the authors try the two grid method as is well analysed from studies of multigrid methods, see for example {open_quotes}Multi-Grid Methods and Applications{close_quotes} by W. Hackbusch. Specifically they consider two discretisations resulting in stiffness matrices A{sub N} and A{sub n}, of size N and n respectively, where N > n, for both a model problem and the geological model. They perform a number of conjugate gradient steps on the fine grid, ie using A{sub N}, followed by an exact coarse grid solve, using A{sub n}, and then update the fine grid solution, the exact coarse grid solve being done using a frontal method factorisation of A{sub n}. Note that in the context of the standard two grid method this is equivalent to using conjugate gradients as a fine grid smoothing step. Experimental results are presented to show the superiority of the two grid iteration method over the polynomial preconditioned conjugate gradient method.

  17. Theoretical investigations on optical properties of magneto-optical thin film on ion-exchanged glass waveguide

    Science.gov (United States)

    Hocini, Abdesselam; Bouras, Mounir; Amata, Hadi

    2013-07-01

    In this work, we report on the theoretical study of magneto-optical waveguides on an ion-exchanged glass waveguide, this latter is made by sol-gel process and doped with magnetic nanoparticles with two kinds of matrix (SiO2/TiO2 and SiO2/ZrO2). The mode propagation and the lateral light confinement for both polarizations TE and TM are simulated using software based on a film mode matching method. We propose from those results magneto-optical waveguides on ion-exchanged glass waveguide geometries for optical integrated applications.

  18. Thermal assisted ion shrinkage (TAIS) of fluorinated polyimide for optical telecommunication devices

    Science.gov (United States)

    Trigaud, T.; Moliton, J. P.; Quillat, M.; Chiron, D.

    1999-06-01

    In the framework of the development of low cost optical devices for telecommunications, here is studied the shrinkage of 6FDA-ODA polyimide films by ion irradiation as a function of five parameters: the ion fluence, the ion fluence rate, the ion energy, the ion nature and the target temperature. In the 30-350 keV energy range for impinging ions, the shrinkage remains constant whatever the tested fluence rate is. An upper limit appears for fluences above 10 16 ions cm -2. The etching is linearly dependent on the ion beam energy and reaches a maximum around 1 μm by thermal assisted ion shrinkage (TAIS) with Na + irradiations.

  19. Morphology Control and Optical Absorption Properties of Ag Nanoparticles by Ion Implantation

    Institute of Scientific and Technical Information of China (English)

    G.X. Cai; F. Ren; X.H. Xiao; L.X. Fan; X.D. Zhou; C.Z. Jiang

    2009-01-01

    Ion implantation is a powerful method for fabricating nanoparticles in dielectric. For the actual application of nanoparticle composites, a careful control of nanoparticles has to be achieved. In this letter, the size, distribution and morphology of Ag nanoparticles are controlled by controlling the ion current density, ion implantation sequence and ion irradiation dose. Single layer Ag nanoparticles are formed by Ag~+ ion implantation at current density of 2.5 μA/cm~2. By Ag and Cu ions sequential implantation, the size of single layer Ag nanoparticles increases. While, by Cu and Ag ions sequential implantation, uniform Ag nanoparticles with wide distribution are formed. The morphology of Ag nanoparticles changes to hollow and sandwiched nanoparticles by Cu~+ ion irradiation to doses of 3×10~(16) and 5×10~(16) ions/cm~2. The optical absorption properties of Ag nanoparticles are also tailored by these ways.

  20. Two-grid method for characteristisc mixed finite-element solutions of nonlinear convection-diffusion equations

    Institute of Scientific and Technical Information of China (English)

    QIN Xinqiang; MA Yichen; GONG Chunqiong

    2004-01-01

    A two-grid method for solving nonlinear convection-dominated diffusion equations is presented. The method use discretizations based on a characteristic mixed finite-element method and give the linearization for nonlinear systems by two steps. The error analysis shows that the two-grid scheme combined with the characteristic mixed finite-element method can decrease numerical oscillation caused by dominated convections and solve nonlinear advection-dominated diffusion problems efficiently.

  1. Ion beam machining error control and correction for small scale optics.

    Science.gov (United States)

    Xie, Xuhui; Zhou, Lin; Dai, Yifan; Li, Shengyi

    2011-09-20

    Ion beam figuring (IBF) technology for small scale optical components is discussed. Since the small removal function can be obtained in IBF, it makes computer-controlled optical surfacing technology possible to machine precision centimeter- or millimeter-scale optical components deterministically. Using a small ion beam to machine small optical components, there are some key problems, such as small ion beam positioning on the optical surface, material removal rate, ion beam scanning pitch control on the optical surface, and so on, that must be seriously considered. The main reasons for the problems are that it is more sensitive to the above problems than a big ion beam because of its small beam diameter and lower material ratio. In this paper, we discuss these problems and their influences in machining small optical components in detail. Based on the identification-compensation principle, an iterative machining compensation method is deduced for correcting the positioning error of an ion beam with the material removal rate estimated by a selected optimal scanning pitch. Experiments on ϕ10 mm Zerodur planar and spherical samples are made, and the final surface errors are both smaller than λ/100 measured by a Zygo GPI interferometer.

  2. High-energy ion treatments of amorphous As40Se60 thin films for optical applications

    OpenAIRE

    Rashmi Chauhan; Arvind Tripathi; Krishna Kant Srivastava

    2014-01-01

    The treatment of 100 MeV Ag swift-heavy ion (SHI) irradiation with five different fluences (3×1010, 1×1011, 3×1011, 1×1012, and 3×1012 ions/cm2) was used to design optical and structural properties of amorphous (a-) As40Se60 chalcogenide thin films. Swanepoel method was applied on transmission measurements to determine the changes in optical bandgap, Tauc parameter and linear optical parameters, i.e., linear optical absorption, extinction coefficient and linear refractive index. Dispersion of...

  3. High-energy ion treatments of amorphous As40Se60 thin films for optical applications

    OpenAIRE

    Chauhan, Rashmi; Tripathi, Arvind; Srivastava, Krishna Kant

    2014-01-01

    The treatment of 100 MeV Ag swift-heavy ion (SHI) irradiation with five different fluences (3×1010, 1×1011, 3×1011, 1×1012, and 3×1012 ions/cm2) was used to design optical and structural properties of amorphous (a-) As40Se60 chalcogenide thin films. Swanepoel method was applied on transmission measurements to determine the changes in optical bandgap, Tauc parameter and linear optical parameters, i.e., linear optical absorption, extinction coefficient and linear refractive index. Dispersion of...

  4. Durable Silver Mirror Coating Via Ion Assisted, Electron Beam Evaporation For Large Aperture Optics Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In the Phase I research, Surface Optics Corporation (SOC) demonstrated a durable silver mirror coating based an ion assisted, thermal evaporation process. The recipe...

  5. Improvement of a polarized alkali ion source by means of optical pumping

    Energy Technology Data Exchange (ETDEWEB)

    Dreves, W.; Koch, E.; Jaensch, H.; Kamke, W.; Broermann, W.; Fick, D.

    1982-01-01

    A source for polarized alkali ions can be improved considerably by optical pumping of the atom beam in combination with a modified weak field transition. M-level populations were investigated using laser induced fluorescence in a magnetic field.

  6. Interferometric pump-probe characterization of the nonlocal response of optically transparent ion implanted polymers

    Science.gov (United States)

    Stefanov, Ivan L.; Hadjichristov, Georgi B.

    2012-03-01

    Optical interferometric technique is applied to characterize the nonlocal response of optically transparent ion implanted polymers. The thermal nonlinearity of the ion-modified material in the near-surface region is induced by continuous wave (cw) laser irradiation at a relatively low intensity. The interferometry approach is demonstrated for a subsurface layer of a thickness of about 100 nm formed in bulk polymethylmethacrylate (PMMA) by implantation with silicon ions at an energy of 50 keV and fluence in the range 1014-1017 cm-2. The laser-induced thermooptic effect in this layer is finely probed by interferometric imaging. The interference phase distribution in the plane of the ion implanted layer is indicative for the thermal nonlinearity of the near-surface region of ion implanted optically transparent polymeric materials.

  7. Cell swelling and ion redistribution assessed with intrinsic optical signals

    Directory of Open Access Journals (Sweden)

    WITTE OTTO W.

    2001-01-01

    Full Text Available Cell volume changes are associated with alterations of intrinsic optical signals (IOS. In submerged brain slices in vitro, afferent stimulation induces an increase in light transmission. As assessed by measurement of the largely membrane impermeant ion tetramethylammonium (TMA in the extracellular space, these IOS correlate with the extent and time course of the change of the extracellular space size. They have a high signal to noise ratio and allow measurements of IOS changes in the order of a few percent. Under conditions of reduced net KCl uptake (low Cl solution a directed spatial buffer mechanism (K syphoning can be demonstrated in the neocortex with widening of the extracellular space in superficial layers associated with a reduced light transmission and an increase of extracellular K concentration. The nature of the IOS under pathophysiological conditions is less clear. Spreading depressions first cause an increase of light transmission, then a decrease. Such a decrease has also been observed following application of NMDA where it was associated with structural damage. Pharmacological analyses suggest that under physiological conditions changes of extracellular space size are mainly caused by astrocytic volume changes while with strong stimuli and under pathophysiological conditions also neuronal swelling occurs. With reflected light usually signals opposite to those observed with transmitted light are seen. Recording of IOS from interface slices gives very complex signals since under these conditions an increase of light transmission has been reported to be superimposed by a decrease of the signal due to mechanical lensing effects of the slice surface. Depending on the method of measurement and the exact conditions, several mechanisms may contribute to IOS. Under well defined conditions IOS are a useful supplementary tool to monitor changes of extracellular volume both in space and time.

  8. A Two-grid Method with Expanded Mixed Element for Nonlinear Reaction-diffusion Equations

    Institute of Scientific and Technical Information of China (English)

    Wei Liu; Hong-xing Rui; Hui Guo

    2011-01-01

    Expanded mixed finite element approximation of nonlinear reaction-diffusion equations is discussed. The equations considered here are used to model the hydrologic and bio-geochemical phenomena. To linearize the mixed-method equations, we use a two-grid method involving a small nonlinear system on a coarse gird of size H and a linear system on a fine grid of size h. Error estimates are derived which demonstrate that the error is O(△t + hk+1 + H2k+2-d/2) (k ≥ 1), where k is the degree of the approximating space for the primary variable and d is the spatial dimension. The above estimates are useful for determining an appropriate H for the coarse grid problems.

  9. Generalized Rayleigh quotient and finite element two-grid discretization schemes

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    This study discusses generalized Rayleigh quotient and high efficiency finite element discretization schemes. Some results are as follows: 1) Rayleigh quotient accelerate technique is extended to nonselfadjoint problems. Generalized Rayleigh quotients of operator form and weak form are defined and the basic relationship between approximate eigenfunction and its generalized Rayleigh quotient is established. 2) New error estimates are obtained by replacing the ascent of exact eigenvalue with the ascent of finite element approximate eigenvalue. 3) Based on the work of Xu Jinchao and Zhou Aihui, finite element two-grid discretization schemes are established to solve nonselfadjoint elliptic differential operator eigenvalue problems and these schemes are used in both conforming finite element and non-conforming finite element. Besides, the efficiency of the schemes is proved by both theoretical analysis and numerical experiments. 4) Iterated Galerkin method, interpolated correction method and gradient recovery for selfadjoint elliptic differential operator eigenvalue problems are extended to nonselfadjoint elliptic differential operator eigenvalue problems.

  10. Generalized Rayleigh quotient and finite element two-grid discretization schemes

    Institute of Scientific and Technical Information of China (English)

    YANG YiDu; FAN XinYue

    2009-01-01

    This study discusses generalized Rayleigh quotient and high efficiency finite element dis-cretization schemes. Some results are as follows: 1) Rayleigh quotient accelerate technique is extended to nonselfadjoint problems. Generalized Rayleigh quotients of operator form and weak form are defined and the basic relationship between approximate eigenfunction and its generalized Rayleigh quotient is established. 2) New error estimates are obtained by replacing the ascent of exact eigenvalue with the ascent of finite element approximate eigenvalue. 3) Based on the work of Xu Jinchao and Zhou Aihui, finite element two-grid discretization schemes are established to solve nonselfadjoint elliptic differential operator eigenvalue problems and these schemes are used in both conforming finite element and non-conforming finite element. Besides, the efficiency of the schemes is proved by both theoretical analysis and numerical experiments. 4) Iterated Galerkin method, interpolated correction method and gradient recovery for selfadjoint elliptic differential operator eigenvalue problems are extended to nonselfadjoint elliptic differential operator eigenvalue problems.

  11. Cavity electromagnetically induced transparency and all-optical switching using ion Coulomb crystals

    DEFF Research Database (Denmark)

    Albert, Magnus; Dantan, Aurelien Romain; Drewsen, Michael

    2011-01-01

    nonlinear interactions, such as those based on electromagnetic induced transparency (EIT)2, 3, 4, 5, 6, 9, 10, 11, 12. Here, we demonstrate for the first time EIT as well as all-optical EIT-based light switching using ion Coulomb crystals situated in an optical cavity. Changes from essentially full...

  12. Researches on the Growth Habit and Optical Properties of Fe3+ Ion Doped KDP Crystal

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    During the process of KDP crystal growth, metal ions strongly affect the growth habit and optical properties of KDP single crystal. In this paper, KDP crystals were grown from an aqueous solution doped with different concentration of Fe3+ dopant by traditional temperaturereduction method and "point-seed" rapid growth method. Furthermore, we examined the light scatter and measured the transmission of these KDP crystals. It is found that the dopant of Fe3+ ion can improve the stability of the KDP growth solution when its concentration is less than 30 ppm.The effects of Fe3+ ion on the growth habit and optical properties of KDP crystal are also obvious.

  13. Fabrication of glass optical power splitter in thallium source by ion-exchange method

    Institute of Scientific and Technical Information of China (English)

    Zigang Zhou(周自刚); Desen Liu(刘德森)

    2003-01-01

    The use of a new thallium-ion (T1+) source for glass optical power splitter fabrication based on a NaNO3-TlaSO4 mixture is proposed and demonstrated. Planar optical power splitters were made using glassessuch as K6, K8, K9. The optical quality of the devices prepared compares favorably with the qualityobtained using other fabrication techniques (such as dry etching) and the processing time is considerablyreduced.

  14. RETRACTED: Optical limiting performance of Ag nanoclusters synthesized by ion implantation

    Science.gov (United States)

    Wang, Y. H.; Wei, L.; Yuan, J.; Wang, R. W.; Lu, J. D.; Ji, L. L.

    2013-01-01

    Metal nanoparticles synthesized by 200 keV Ag ions into silica with dose of 2×1017 ions/cm2 has been studied. Third-order nonlinear optical properties of the nanoparticles were measured at 1064 nm excitations using the Z-scan technique. Results of the investigation of nonlinear refraction by the single beam Z-scan configuration are presented and the mechanisms responsible for the nonlinear response were discussed. Curve fitting analysis, based on MATLAB features for Ag nanoparticle optical limiting experiment, is used. The results show that Ag nanoparticles display a refractive optical limiting effect at 1064 nm.

  15. High-energy ion treatments of amorphous As40Se60 thin films for optical applications

    Directory of Open Access Journals (Sweden)

    Rashmi Chauhan

    2014-06-01

    Full Text Available The treatment of 100 MeV Ag swift-heavy ion (SHI irradiation with five different fluences (3×1010, 1×1011, 3×1011, 1×1012, and 3×1012 ions/cm2 was used to design optical and structural properties of amorphous (a- As40Se60 chalcogenide thin films. Swanepoel method was applied on transmission measurements to determine the changes in optical bandgap, Tauc parameter and linear optical parameters, i.e., linear optical absorption, extinction coefficient and linear refractive index. Dispersion of the material was determined by Wemple–DiDomenico relation. Changes in nonlinear optical parameters of third-order optical susceptibility and nonlinear refractive index were determined using semi-empirical relations. Changes in surface morphology of the films were investigated using SEM observation, which indicated that fluence 3×1012 ions/cm2 was upper threshold limit for these films for ion treatment. It is observed that optical bandgap reduces from 1.76 eV to 1.64 eV, and nonlinear refractive index increases from 1.31×10−10 [esu] to 1.74×10−10 [esu]. Linear refractive index initially increases from 2.80 to 3.52 (for fluence 3×1010 ions/cm2 and then keeps decreasing. The observed changes in optical properties upon irradiation were explained in terms of structural rearrangements by Raman measurement. The study was compiled with the previous literature to propose SHI as an effective optical engineering technique to achieve desired changes according to the need of optical/photonic applications.

  16. High-energy ion treatments of amorphous As40Se60 thin films for optical applications

    Institute of Scientific and Technical Information of China (English)

    Rashmi Chauhan; Arvind Tripathi; Krishna Kant Srivastava

    2014-01-01

    The treatment of 100 MeV Ag swift-heavy ion (SHI) irradiation with five different fluences (3 ? 1010, 1 ? 1011, 3 ? 1011, 1 ? 1012, and 3 ? 1012 ions/cm2) was used to design optical and structural properties of amorphous (a-) As40Se60 chalcogenide thin films. Swanepoel method was applied on transmission measurements to determine the changes in optical bandgap, Tauc parameter and linear optical parameters, i.e., linear optical absorption, extinction coefficient and linear refractive index. Dispersion of the material was determined by Wemple-DiDomenico relation. Changes in nonlinear optical parameters of third-order optical susceptibility and nonlinear refractive index were determined using semi-empirical relations. Changes in surface morphology of the films were investigated using SEM observation, which indicated that fluence 3 ? 1012 ions/cm2 was upper threshold limit for these films for ion treatment. It is observed that optical bandgap reduces from 1.76 eV to 1.64 eV, and nonlinear refractive index increases from 1.31 ? 10 ? 10 [esu] to 1.74 ? 10 ? 10 [esu]. Linear refractive index initially increases from 2.80 to 3.52 (for fluence 3 ? 1010 ions/cm2) and then keeps decreasing. The observed changes in optical properties upon irradiation were explained in terms of structural rearrangements by Raman measurement. The study was compiled with the previous literature to propose SHI as an effective optical engineering technique to achieve desired changes according to the need of optical/photonic applications.

  17. Optical properties of swift ion beam irradiated CdTe thin films

    Energy Technology Data Exchange (ETDEWEB)

    Chandramohan, S. [PG and Research Department of Physics, Kongunadu Arts and Science College, Coimbatore, Tamilnadu 641029 (India); Sathyamoorthy, R. [PG and Research Department of Physics, Kongunadu Arts and Science College, Coimbatore, Tamilnadu 641029 (India)], E-mail: rsathya59@yahoo.co.in; Sudhagar, P. [PG and Research Department of Physics, Kongunadu Arts and Science College, Coimbatore, Tamilnadu 641029 (India); Kanjilal, D.; Kabiraj, D.; Asokan, K. [Inter-University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India)

    2008-06-30

    This paper reports the effect of swift (80 MeV) oxygen (O{sup +6}) ion irradiation on the optical properties of CdTe thin films grown by conventional thermal evaporation on glass substrates. The films are found to be slightly Te-rich in composition and irradiation results no change in the elemental composition. The optical constants such as refractive index (n), absorption coefficient ({alpha}) and the optical band gap energy show significant variation in their values with increase in ion fluence. Upon irradiation the band gap energy decreased from a value of 1.53 eV to 1.46 eV whereas the refractive index (n) increased from 2.38 to 3.12 at {lambda} = 850 nm. The photoluminescence spectrum shows high density of native defects whose density strongly depends on the ion fluence. Both analyses indicate considerable defect production after swift ion beam irradiation.

  18. Optical and magnetic properties of nitrogen ion implanted MgO single crystal

    Institute of Scientific and Technical Information of China (English)

    Liu Chun-Ming; Gu Hai-Quan; Xiang Xia; Zhang Yan; Jiang Yong; Chen Meng; Zu Xiao-Tao

    2011-01-01

    The microstructure, optical property and magnetism of nitrogen ion implanted single MgO crystals are studied.A parallel investigation is also performed in an iron ion implanted single MgO sample as a reference. Large structural,optical and magnetic differences are obtained between the nitrogen and iron implanted samples. Room temperature ferromagnetism with a fairly large coercivity field of 300 Oe (1 Oe=79.5775 A/m), a remanence of 38% and a slightly changed optical absorption is obtained in the sample implanted using nitrogen with a dose of 1×1018 ions/cm2. Transition metal contamination and defects induced magnetism can be excluded when compared with those of the iron ion implanted sample, and the nitrogen doping is considered to be the main origin of ferromagnetism.

  19. Estimate of Lifetime of Ion Thruster Optics Based on Particle Simulation

    Institute of Scientific and Technical Information of China (English)

    LIU Chang; TANG Haibin; ZHANG Zhenpeng; GU Zuo; LIU Yu

    2008-01-01

    A three-dimensional particle simulation of ion thruster optics with charge-exchange collision was developed in this study. The simulation code was based on tracking ions using the particle-in-cell method, and the Monte Carlo technique was used to model the charge-exchange collision. Simulations were performed for a 20 cm ion thruster optics. The results were compared with the corresponding experimental data from a test of the ion thruster optics for a duration of 800 hours. The Depth-From-Focus (DFF) method was used to measure the erosion depth of the downstream surface of the accelerator grid. The predicted erosion depth of the accelerator grid was consistent reasonably with the corresponding experimental data. The simulation results showed that the accelerator grid would be burned through after 1333 hours.

  20. A far-off-resonance optical trap for a Ba$^+$ ion

    CERN Document Server

    Huber, Thomas; Schmidt, Julian; Karpa, Leon; Schaetz, Tobias

    2014-01-01

    Optical trapping and ions combine unique advantages of independently striving fields of research. Light fields can form versatile potential landscapes, such as optical lattices, for neutral and charged atoms, avoiding detrimental implications of established radiofrequency (rf) traps while mediating interaction via long range Coulomb forces, controlling and detecting motional and electronic states on the quantum level. Here we show optical trapping of $^{138}$Ba$^{+}$ ions in the absence of rf fields in a far-detuned dipole trap, suppressing photon scattering by three and the related recoil heating by four orders of magnitude. To enhance the prospects for optical as well as hybrid traps, we demonstrate a novel method for stray electric field compensation to a level below 9 mV/m. Our results will be relevant, for example, for ion-atom ensembles, to enable four to five orders of magnitude lower common temperatures, accessing the regime of ultracold interaction and chemistry, where quantum effects are predicted t...

  1. An ion-optical design study of a carbon-ion rotating gantry with a superconducting final bending magnet

    Energy Technology Data Exchange (ETDEWEB)

    Bokor, J., E-mail: jozef.bokor@stuba.sk; Pavlovič, M.

    2016-03-11

    Ion-optical designs of an isocentric ion gantry with a compact curved superconducting final bending magnet are presented. The gantry is designed for transporting carbon-therapy beams with nominal kinetic energy of 400 MeV/u, which corresponds to the penetration range of C{sup 6+} beam in water of about 28 cm. In contrast to other existing designs, we present a “hybrid” beam transport system containing a single superconducting element – the last bending magnet. All other elements are based on conventional warm technology. Ion-optical properties of such a hybrid system are investigated in case of transporting non-symmetric (i.e. different emittance patterns in the horizontal and vertical plane) beams. Different conditions for transporting the non-symmetric beams are analyzed aiming at finding the optimal, i.e. the most compact, gantry version. The final gantry layout is presented including a 2D parallel scanning. The ion-optical and scanning properties of the final gantry design are described, discussed and illustrated by computer simulations performed by WinAGILE.

  2. An ion-optical design study of a carbon-ion rotating gantry with a superconducting final bending magnet

    Science.gov (United States)

    Bokor, J.; Pavlovič, M.

    2016-03-01

    Ion-optical designs of an isocentric ion gantry with a compact curved superconducting final bending magnet are presented. The gantry is designed for transporting carbon-therapy beams with nominal kinetic energy of 400 MeV/u, which corresponds to the penetration range of C6+ beam in water of about 28 cm. In contrast to other existing designs, we present a ;hybrid; beam transport system containing a single superconducting element - the last bending magnet. All other elements are based on conventional warm technology. Ion-optical properties of such a hybrid system are investigated in case of transporting non-symmetric (i.e. different emittance patterns in the horizontal and vertical plane) beams. Different conditions for transporting the non-symmetric beams are analyzed aiming at finding the optimal, i.e. the most compact, gantry version. The final gantry layout is presented including a 2D parallel scanning. The ion-optical and scanning properties of the final gantry design are described, discussed and illustrated by computer simulations performed by WinAGILE.

  3. A Linear Ion Trap with an Expanded Inscribed Diameter to Improve Optical Access for Fluorescence Spectroscopy

    Science.gov (United States)

    Rajagopal, Vaishnavi; Stokes, Chris; Ferzoco, Alessandra

    2017-08-01

    We report a custom-geometry linear ion trap designed for fluorescence spectroscopy of gas-phase ions at ambient to cryogenic temperatures. Laser-induced fluorescence from trapped ions is collected from between the trapping rods, orthogonal to the excitation laser that runs along the axis of the linear ion trap. To increase optical access to the ion cloud, the diameter of the round trapping rods is 80% of the inscribed diameter, rather than the roughly 110% used to approximate purely quadrupolar electric fields. To encompass as much of the ion cloud as possible, the first collection optic has a 25.4 mm diameter and a numerical aperture of 0.6. The choice of geometry and collection optics yields 107 detected photons/s from trapped rhodamine 6G ions. The trap is coupled to a closed-cycle helium refrigerator, which in combination with two 50 Ohm heaters enables temperature control to below 25 K on the rod electrodes. The purpose of the instrument is to broaden the applicability of fluorescence spectroscopy of gas-phase ions to cases where photon emission is a minority relaxation pathway. Such studies are important to understand how the microenvironment of a chromophore influences excited state charge transfer processes. [Figure not available: see fulltext.

  4. Nanoporous gold based optical sensor for sub-ppt detection of mercury ions.

    Science.gov (United States)

    Zhang, Ling; Chang, Haixin; Hirata, Akihiko; Wu, Hongkai; Xue, Qi-Kun; Chen, Mingwei

    2013-05-28

    Precisely probing heavy metal ions in water is important for molecular biology, environmental protection, and healthy monitoring. Although many methods have been reported in the past decade, developing a quantitative approach capable of detecting sub-ppt level heavy metal ions with high selectivity is still challenging. Here we report an extremely sensitive and highly selective nanoporous gold/aptamer based surface enhanced resonance Raman scattering (SERRS) sensor. The optical sensor has an unprecedented detection sensitivity of 1 pM (0.2 ppt) for Hg(2+) ions, the most sensitive Hg(2+) optical sensor known so far. The sensor also exhibits excellent selectivity. Dilute Hg(2+) ions can be identified in an aqueous solution containing 12 metal ions as well as in river water and underground water. Moreover, the SERRS sensor can be reused without an obvious loss of the sensitivity and selectivity even after 10 cycles.

  5. One single trapped and laser cooled radium ion: Towards an all-optical atomic clock

    Energy Technology Data Exchange (ETDEWEB)

    Versolato, Oscar; Wansbeek, Lotje; Willmann, Lorenz; Timmermans, Rob; Jungmann, Klaus [KVI, University of Groningen (Netherlands)

    2008-07-01

    One single trapped radium ion is an ideal candidate for an all-optical frequency standard (*clock*). This system provides a long coherence time and tractable systematics. If the ion is laser cooled to the Lamb-Dicke regime, first order Doppler shifts are eliminated. Ultra-narrow transitions in radium ions provide an excellent basis for such a high stability clock, using commercially available semiconductor lasers in the visible regime. In certain odd isotopes of radium, the nuclear electric quadrupole shift is absent. Further, the radium ion is an excellent candidate for a high sensitivity experiment to search for a time variation of the finestructure constant.

  6. Ion optics and beam dynamics optimization at the HESR storage ring for the SPARC experiments with highly charged heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Kovalenko, Oleksandr

    2015-06-24

    The High-Energy Storage Ring (HESR) is a part of an upcoming International Facility for Antiproton and Ion Research (FAIR) at GSI in Darmstadt. A key part of a scientific program, along with antiproton physics, will be physics with highly-charged heavy ions. Phase-space cooled beams together with fixed internal target will provide an excellent environment for storage ring experiments at the HESR for the SPARC collaboration. Until recently, however, the existing ion optical lattice for the HESR was designed only for the experiments with antiproton beams. The thesis presents a new ion optical mode developed specifically for the operation of the HESR with highly charged heavy ions. The presence of the errors, such as beam momentum spread, magnetic field impurities or magnets misalignments, leads to disruption of beam dynamics: exciting of resonant motion and loss of beam stability. Within the paper, these effects are investigated with the help of numerical codes for particle accelerator design and simulation MAD-X and MIRKO. A number of correction techniques are applied to minimize the nonlinear impact on the beam dynamics and improve the experimental conditions. The application of the analytical and numerical tools is demonstrated in the experiment with uranium U{sup 90+} beam at the existing storage ring ESR, GSI.

  7. TWO-GRID METHOD FOR CHARACTERISTICS FINITE-ELEMENT SOLUTION OF 2D NONLINEAR CONVECTION-DOMINATED DIFFUSION PROBLEM

    Institute of Scientific and Technical Information of China (English)

    QIN Xin-qiang; MA Yi-chen; ZHANG Yin

    2005-01-01

    For two-dimension nonlinear convection diffusion equation, a two-grid method of characteristics finite-element solution was constructed. In this method the nonlinear iterations is only to execute on the coarse grid and the fine-grid solution can be obtained in a single linear step. For the nonlinear convection-dominated diffusion equation, this method can not only stabilize the numerical oscillation but also accelerate the convergence and improve the computational efficiency. The error analysis demonstrates if the mesh sizes between coarse-grid and fine-grid satisfy the certain relationship, the two-grid solution and the characteristics finite-element solution have the same order of accuracy. The numerical example confirms that the two-grid method is more efficient than that of characteristics finite-element method.

  8. Multisectional linear ion trap and novel loading method for optical spectroscopy of electron and nuclear transitions.

    Science.gov (United States)

    Sysoev, Alexey A; Troyan, Victor I; Borisyuk, Peter V; Krasavin, Andrey V; Vasiliev, Oleg S; Palchikov, Vitaly G; Avdeev, Ivan A; Chernyshev, Denis M; Poteshin, Sergey S

    2015-01-01

    There is a growing need for the development of atomic and nuclear frequency standards because of the important contribution of methods for precision time and frequency measurements to the development of fundamental science, technology, and the economy. It is also conditioned by their potential use in optical clocks and quantum logic applications. It is especially important to develop a universal method that could allow one to use ions of most elements effectively (including ones that are not easily evaporated) proposed for the above-mentioned applications. A linear quadrupole ion trap for the optical spectroscopy of electron and nuclear transitions has been developed and evaluated experimentally. An ion source construction is based on an ultra-high vacuum evaporator in which a metal sample is subjected to an electron beam of energy up to 1 keV, resulting in the appearance of gaseous atoms and ions of various charge state. The linear ion trap consists of five successive quadrupole sections including an entrance quadrupole section, quadrupole mass filter, quadrupole ion guide, ion-trap section, and exit quadrupole section. The same radiofrequency but a different direct current voltage feeds the quadrupole sections. The instrument allows the mass and energy selected trapping of ions from ion beams of various intensities and their localization in the area of laser irradiation. The preliminary results presented show that the proposed instrument and methods allow one to produce effectively up to triply charged thorium ions as well as to trap ions for future spectroscopic study. The instrument is proposed for future use in optical clocks and quantum logic application development.

  9. Optical absorption enhancement of CdTe nanostructures by low-energy nitrogen ion bombardment

    Science.gov (United States)

    Akbarnejad, E.; Ghoranneviss, M.; Mohajerzadeh, S.; Hantehzadeh, M. R.; Asl Soleimani, E.

    2016-02-01

    In this paper we present the fabrication of cadmium telluride (CdTe) nanostructures by means of RF magnetron sputtering followed by low-energy ion implantation and post-thermal treatment. We have thoroughly studied the structural, optical, and morphological properties of these nanostructures. The effects of nitrogen ion bombardment on the structural parameters of CdTe nanostructures such as crystal size, microstrain, and dislocation density have been examined. From x-ray diffractometer (XRD) analysis it could be deduced that N+ ion fluence and annealing treatment helps to form (3 0 0) orientation in the crystalline structure of cadmium-telluride films. Fluctuations in optical properties like the optical band gap and absorption coefficient as a function of N+ ion fluences have been observed. The annealing of the sample irradiated by a dose of 1018 ions cm-2 has led to great enhancement in the optical absorption over a wide range of wavelengths with a thickness of 250 nm. The enhanced absorption is significantly higher than the observed value in the original CdTe layer with a thickness of 3 μm. Surface properties such as structure, grain size and roughness are noticeably affected by varying the nitrogen fluences. It is speculated that nitrogen bombardment and post-annealing treatment results in a smaller optical band gap, which in turn leads to higher absorption. Nitrogen bombardment is found to be a promising method to increase efficiency of thin film solar cells.

  10. Is the Multigrid Method Fault Tolerant? The Two-Grid Case

    Energy Technology Data Exchange (ETDEWEB)

    Ainsworth, Mark [Brown Univ., Providence, RI (United States). Division of Applied Mathematics; Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Computer Science and Mathematics Division; Glusa, Christian [Brown Univ., Providence, RI (United States). Division of Applied Mathematics

    2016-06-30

    The predicted reduced resiliency of next-generation high performance computers means that it will become necessary to take into account the effects of randomly occurring faults on numerical methods. Further, in the event of a hard fault occurring, a decision has to be made as to what remedial action should be taken in order to resume the execution of the algorithm. The action that is chosen can have a dramatic effect on the performance and characteristics of the scheme. Ideally, the resulting algorithm should be subjected to the same kind of mathematical analysis that was applied to the original, deterministic variant. The purpose of this work is to provide an analysis of the behaviour of the multigrid algorithm in the presence of faults. Multigrid is arguably the method of choice for the solution of large-scale linear algebra problems arising from discretization of partial differential equations and it is of considerable importance to anticipate its behaviour on an exascale machine. The analysis of resilience of algorithms is in its infancy and the current work is perhaps the first to provide a mathematical model for faults and analyse the behaviour of a state-of-the-art algorithm under the model. It is shown that the Two Grid Method fails to be resilient to faults. Attention is then turned to identifying the minimal necessary remedial action required to restore the rate of convergence to that enjoyed by the ideal fault-free method.

  11. Tailoring the structural and optical properties of TiN thin films by Ag ion implantation

    Science.gov (United States)

    Popović, M.; Novaković, M.; Rakočević, Z.; Bibić, N.

    2016-12-01

    Titanium nitride (TiN) thin films thickness of ∼260 nm prepared by dc reactive sputtering were irradiated with 200 keV silver (Ag) ions to the fluences ranging from 5 × 1015 ions/cm2 to 20 × 1015 ions/cm2. After implantation TiN layers were annealed 2 h at 700 °C in a vacuum. Ion irradiation-induced microstructural changes were examined by using Rutherford backscattering spectrometry, X-ray diffraction and transmission electron microscopy, while the surface topography was observed using atomic force microscopy. Spectroscopic ellipsometry was employed to get insights on the optical and electronic properties of TiN films with respect to their microstructure. The results showed that the irradiations lead to deformation of the lattice, increasing disorder and formation of new Ag phase. The optical results demonstrate the contribution of surface plasmon resonace (SPR) of Ag particles. SPR position shifted in the range of 354.3-476.9 nm when Ag ion fluence varied from 5 × 1015 ions/cm2 to 20 × 1015 ions/cm2. Shift in peak wavelength shows dependence on Ag particles concentration, suggesting that interaction between Ag particles dominate the surface plasmon resonance effect. Presence of Ag as second metal in the layer leads to overall decrease of optical resistivity of TiN.

  12. Redox ratio and optical absorption of polyvalent ions in industrial glasses

    Indian Academy of Sciences (India)

    W Thiemsorn; K Keowkamnerd; P Suwannathada; H Hessenkemper; S Phanichaphant

    2007-10-01

    The changes in glass structure and redox ratio, (reduced ion to oxidized ion) of Mn2+–Mn3+, Cu+–Cu2+, Cr3+–Cr6+, Ni2+–Ni3+ and Co2+–Co3+ couples and optical absorption due to Mn3+, Cu2+, Cr3+, Ni2+ and Co2+ ions in industrial soda–lime–silica glass were investigated as a function of Na2O concentration in the range 11–19 mol%. With increasing Na2O concentration in the experimental glasses, the basicity, expressed as calculated basicity, cal, increased. 29Si NMR and X-ray diffraction were used to investigate the structural change in glasses. The NMR spectra showed high non-bridging oxygens (NBOs) when the basicity of glass was increased. The results were interpreted to be due to the tetrahedral networks; 4 species were depolymerized by replacing the bridging oxygens (BOs) with NBOs to 3 species. These results confirmed the shift of broadening peaks of XRD patterns. The redox reactions of the Mn2+–Mn3+, Cu+–Cu2+ and Cr3+–Cr6+ couples shifted more toward their oxidized ions due to the oxygen partial pressure, (2), during melting and the oxide ion activity, O2–, increased with increasing glass basicity. These changes caused the redox ratio of these ion couples to decrease. The Ni2+–Ni3+ and Co2+–Co3+ couples were assumed to be present only in the Ni2+ and Co2+ ions in these glasses, respectively. The optical absorption bands due to Mn3+, Cu2+, Cr3+, Ni2+ and Co2+ ions were also investigated. Their spectra occurred at constant wavelengths with different optical densities or intensities as a function of glass basicity. The increase in the intensities of the absorption bands of these absorbing ions, except for Cr3+ ion, at the maximum wavelength, depends not only on the ion concentration but also on the increase of polarizability of oxide (–II) species, oxide(–II), surrounding the ions. This value affected directly the extinction coefficients of the ions, ion. The increase of ion caused the colour of glasses appearing in high intensity. In

  13. Comparative numerical studies of ion traps with integrated optical cavities

    CERN Document Server

    Podoliak, Nina; Keller, Matthias; Horak, Peter

    2016-01-01

    We study a range of radio-frequency ion trap geometries and investigate the effect of integrating dielectric cavity mirrors on their trapping potential. We aim to identify ion trap and cavity configurations that are best suited for achieving small cavity volumes and thus large ion-photon coupling as required for scalable quantum information networks. In particular, we investigate the trapping potential distortions caused by the dielectric material of the cavity mirrors for different mirror orientations with respect to the trapping electrodes, as well as for mirror misalignment. We also analyze the effect of the mirror material properties such as dielectric constants and surface conductivity, and study the effect of surface charges on the mirrors. The smallest trapping potential distortions are found if the cavities are aligned along the major symmetry axis of the electrode geometries. These cavity configurations also appear to be the most stable with respect to any mirror misalignment.

  14. Analysis of the fine structure of Sn$^{11+...14+}$ ions by optical spectroscopy in an electron beam ion trap

    CERN Document Server

    Windberger, A; Borschevsky, A; Ryabtsev, A; Dobrodey, S; Bekker, H; Eliav, E; Kaldor, U; Ubachs, W; Hoekstra, R; López-Urrutia, J R Crespo; Versolato, O O

    2016-01-01

    We experimentally re-evaluate the fine structure of Sn$^{11+...14+}$ ions. These ions are essential in bright extreme-ultraviolet (EUV) plasma-light sources for next-generation nanolithography, but their complex electronic structure is an open challenge for both theory and experiment. We combine optical spectroscopy of magnetic dipole $M1$ transitions, in a wavelength range covering 260\\,nm to 780\\,nm, with charge-state selective ionization in an electron beam ion trap. Our measurements confirm the predictive power of \\emph{ab initio} calculations based on Fock space coupled cluster theory. We validate our line identification using semi-empirical Cowan calculations with adjustable wavefunction parameters. Available Ritz combinations further strengthen our analysis. Comparison with previous work suggests that line identifications in the EUV need to be revisited.

  15. Optical characterization of ZnO nanomaterial with praseodymium ions

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Y. K., E-mail: dryksharma@yahoo.com; Bind, Umesh Chandra [Department of Physics, Centre of Nanotechnology, IIT Roorkee (India); Pal, Sudha, E-mail: namansingh91@gmail.com; Goyal, Priyanka, E-mail: namansingh91@gmail.com

    2016-05-06

    ZnO nanomaterial with praseodymium ions was prepared by chemical synthesis method. The ZnO nanomaterial was characterized by XRD, SEM and TEM. Their absorption in UV-VIS/NIR regions was measured at room temperature. The experimental oscillator strengths were calculated from the areas under the absorption bands. Eight absorption bands have been observed. From these spectral data various energy interaction parameters like Slater–Condon, Lande, Racah, Nephelauxetic ratio and bonding parameters have been computed. Judd-Ofelt analysis has been carried out using the absorption spectra to evaluate the radiative properties for luminescent levels of the praseodymium ion and discussed. The observed nano particle size is 2nm.

  16. Optical characterization of ZnO nanomaterial with praseodymium ions

    Science.gov (United States)

    Sharma, Y. K.; Pal, Sudha; Goyal, Priyanka; Bind, Umesh Chandra

    2016-05-01

    ZnO nanomaterial with praseodymium ions was prepared by chemical synthesis method. The ZnO nanomaterial was characterized by XRD, SEM and TEM. Their absorption in UV-VIS/NIR regions was measured at room temperature. The experimental oscillator strengths were calculated from the areas under the absorption bands. Eight absorption bands have been observed. From these spectral data various energy interaction parameters like Slater-Condon, Lande, Racah, Nephelauxetic ratio and bonding parameters have been computed. Judd-Ofelt analysis has been carried out using the absorption spectra to evaluate the radiative properties for luminescent levels of the praseodymium ion and discussed. The observed nano particle size is 2nm.

  17. Optical Tagging of Ion Beams Accelerated by Double Layers in Laboratory Plasma

    Science.gov (United States)

    Good, Timothy; Aguirre, Evan; Thompson, Derek; Scime, Earl

    2016-10-01

    Experiments in helicon sources that investigate plasma expansion into weakly magnetized, low density regions reveal the production of supersonic ion beams attributed to acceleration by spatially localized double layer structures. Current efforts are aimed at mapping the ion velocity flow field utilizing 2D spatially scanning laser induced fluorescence (LIF) probes that yield metastable ion velocity distribution functions (IVDF) for velocities along and perpendicular to the flow. Observation of metastable ion beams by LIF renders plausible a Lagrangian approach to studying the field-ion interaction via optical tagging. We propose a tagging scheme in which metastable state ion populations are modulated by optical pumping upstream of the double layer and the synchronous detection of LIF at the ion beam velocity is recorded downstream. Besides the unambiguous identification of the source of beam ions, this method can provide detailed dynamical information through time of flight analysis. Preliminary results will be presented. Please include this poster in session that includes poster authored by Evan Aguirre et al.

  18. Spatial distribution of charged particles along the ion-optical axis in electron cyclotron resonance ion sources. Experimental results

    Energy Technology Data Exchange (ETDEWEB)

    Panitzsch, Lauri

    2013-02-08

    The experimental determination of the spatial distribution of charged particles along the ion-optical axis in electron cyclotron resonance ion sources (ECRIS) defines the focus of this thesis. The spatial distributions of different ion species were obtained in the object plane of the bending magnet ({approx}45 cm downstream from the plasma electrode) and in the plane of the plasma electrode itself, both in high spatial resolution. The results show that each of the different ion species forms a bloated, triangular structure in the aperture of the plasma electrode. The geometry and the orientation of these structures are defined by the superposition of the radial and axial magnetic fields. The radial extent of each structure is defined by the charge of the ion. Higher charge states occupy smaller, more concentrated structures. The total current density increases towards the center of the plasma electrode. The circular and star-like structures that can be observed in the beam profiles of strongly focused, extracted ion beams are each dominated by ions of a single charge state. In addition, the spatially resolved current density distribution of charged particles in the plasma chamber that impinge on the plasma electrode was determined, differentiating between ions and electrons. The experimental results of this work show that the electrons of the plasma are strongly connected to the magnetic field lines in the source and thus spatially well confined in a triangular-like structure. The intensity of the electrons increases towards the center of the plasma electrode and the plasma chamber, as well. These electrons are surrounded by a spatially far less confined and less intense ion population. All the findings mentioned above were already predicted in parts by simulations of different groups. However, the results presented within this thesis represent the first (and by now only) direct experimental verification of those predictions and are qualitatively transferable to

  19. Phase-Stable Free-Space Optical Lattices for Trapped Ions.

    Science.gov (United States)

    Schmiegelow, C T; Kaufmann, H; Ruster, T; Schulz, J; Kaushal, V; Hettrich, M; Schmidt-Kaler, F; Poschinger, U G

    2016-01-22

    We demonstrate control of the absolute phase of an optical lattice with respect to a single trapped ion. The lattice is generated by off-resonant free-space laser beams, and we actively stabilize its phase by measuring its ac-Stark shift on a trapped ion. The ion is localized within the standing wave to better than 2% of its period. The locked lattice allows us to apply displacement operations via resonant optical forces with a controlled direction in phase space. Moreover, we observe the lattice-induced phase evolution of spin superposition states in order to analyze the relevant decoherence mechanisms. Finally, we employ lattice-induced phase shifts for inferring the variation of the ion position over the 157  μm range along the trap axis at accuracies of better than 6 nm.

  20. Phase-stable free-space optical lattices for trapped ions

    CERN Document Server

    Schmiegelow, Christian Tomas; Ruster, Thomas; Schulz, Jonas; Kaushal, Vidyut; Hettrich, Max; Schmidt-Kaler, Ferdinand; Poschinger, Ulrich G

    2016-01-01

    We demonstrate control of the absolute phase of an optical lattice with respect to a single trapped ion. The lattice is generated by off-resonant free-space laser beams, we actively stabilize its phase by measuring its ac-Stark shift on a trapped ion. The ion is localized within the standing wave to better than 2\\% of its period. The locked lattice allows us to apply displacement operations via resonant optical forces with a controlled direction in phase space. Moreover, we observe the lattice-induced phase evolution of spin superposition states in order to analyze the relevant decoherence mechanisms. Finally, we employ lattice-induced phase shifts for inferring the variation of the ion position over 157~$\\mu$m range along the trap axis at accuracies of better than 6~nm.

  1. Radical-ion-pair reactions are the biochemical equivalent of the optical double slit experiment

    OpenAIRE

    Kominis, I. K.

    2010-01-01

    Radical-ion-pair reactions were recently shown to represent a rich biophysical laboratory for the application of quantum measurement theory methods and concepts. We here show that radical-ion-pair reactions essentially form a non-linear biochemical double slit interferometer. Quantum coherence effects are visible when "which-path" information is limited, and the incoherent limit is approached when measurement-induced decoherence sets in. Based on this analogy with the optical double slit expe...

  2. Crystal optics for hard-X-ray spectroscopy of highly charged ions

    OpenAIRE

    Beyer, H. F.; Attia, D.; Banas, D; Bigot, E. -O. Le; Bosch, F.; Dousse, Jean-Claude; Förster, E.; Gumberidze, A.; Hagmann, S.; Heß, S.; J. Hoszowska; Indelicato, P.; Jagodzinski, P.; Kozhuharov, Chr.; Krings, Th.

    2009-01-01

    A twin crystal-spectrometer assembly, operated in the focusing compensated asymmetric Laue geometry has been developed for accurate spectroscopy of fast highly charged heavy ions in the hard-X-ray region. Coupled to the focusing crystal optics is a specially developed two-dimensional position-sensitive X-ray detector which is necessary for retaining spectral resolution also for fast moving sources. We summarize the crystal optics and demonstrate the usefulness of the instrument for spectrosco...

  3. Ultrafast optical phase modulation with metallic nanoparticles in ion-implanted bilayer silica

    Energy Technology Data Exchange (ETDEWEB)

    Torres-Torres, C [Seccion de Estudios de Posgrado e Investigacion, ESIME-Z, Instituto Politecnico Nacional, Mexico, DF, 07738 (Mexico); Tamayo-Rivera, L; Silva-Pereyra, H G; Reyes-Esqueda, J A; Rodriguez-Fernandez, L; Crespo-Sosa, A; Cheang-Wong, J C; Oliver, A [Instituto de Fisica, Universidad Nacional Autonoma de Mexico, 04510, Mexico, DF (Mexico); Rangel-Rojo, R [Departamento de Optica, Centro de Investigacion Cientifica y de Educacion Superior de Ensenada Apartado Postal 360, Ensenada, BC, 22860 (Mexico); Torres-Martinez, R, E-mail: crstorres@yahoo.com.mx [Centro de Investigacion en Ciencia Aplicada y TecnologIa Avanzada Unidad Queretaro, Instituto Politecnico Nacional, Santiago de Queretaro, Queretaro, 76090 (Mexico)

    2011-09-02

    The nonlinear optical response of metallic-nanoparticle-containing composites was studied with picosecond and femtosecond pulses. Two different types of nanocomposites were prepared by an ion-implantation process, one containing Au nanoparticles (NPs) and the other Ag NPs. In order to measure the optical nonlinearities, we used a picosecond self-diffraction experiment and the femtosecond time-resolved optical Kerr gate technique. In both cases, electronic polarization and saturated absorption were identified as the physical mechanisms responsible for the picosecond third-order nonlinear response for a near-resonant 532 nm excitation. In contrast, a purely electronic nonlinearity was detected at 830 nm with non-resonant 80 fs pulses. Regarding the nonlinear optical refractive behavior, the Au nanocomposite presented a self-defocusing effect, while the Ag one presented the opposite, that is, a self-focusing response. But, when evaluating the simultaneous contributions when the samples are tested as a multilayer sample (silica-Au NPs-silica-Ag NPs-silica), we were able to obtain optical phase modulation of ultra-short laser pulses, as a result of a significant optical Kerr effect present in these nanocomposites. This allowed us to implement an ultrafast all-optical phase modulator device by using a combination of two different metallic ion-implanted silica samples. This control of the optical phase is a consequence of the separate excitation of the nonlinear refracting phenomena exhibited by the separate Au and Ag nanocomposites.

  4. Optically induced structural phase transitions in ion Coulomb crystals

    DEFF Research Database (Denmark)

    Horak, Peter; Dantan, Aurelien Romain; Drewsen, Michael

    2012-01-01

    , such as body-centered cubic and face-centered cubic, can be suppressed by a proper choice of the potential depth and periodicity. Furthermore, by varying the harmonic trap parameters and/or the optical potential in time, controlled transitions between crystal structures can be obtained with close to unit...

  5. Testing spatial α-variation with optical atomic clocks based on highly charged ions

    Directory of Open Access Journals (Sweden)

    Berengut J. C.

    2013-08-01

    Full Text Available We review recent works illustrating the potential use of highly charged ions as the basis of optical atomic clocks of exceptional accuracy and very high sensitivity to variation of the fine structure constant, α. The tendency towards large transition energies in highly charged ions can be overcome using level crossings, which allow transitions between different orbitals to be within the range of usual lasers. We present simple scaling laws that demonstrate reduced systematics that could be realised in highly charged ion clocks. Such clocks could allow us to corroborate astronomical studies that suggest a spatial gradient in values of α across the Universe.

  6. Synthesis and Characterization of Layered Double Hydroxides Containing Optically Active Transition Metal Ion

    Science.gov (United States)

    Tyagi, S. B.; Kharkwal, Aneeta; Nitu; Kharkwal, Mamta; Sharma, Raghunandan

    2017-01-01

    The acetate intercalated layered double hydroxides of Zn and Mn, have been synthesized by chimie douce method. The materials were characterized by XRD, TGA, CHN, IR, XPS, SEM-EDX and UV-visible spectroscopy. The photoluminescence properties was also studied. The optical properties of layered hydroxides are active transition metal ion dependent, particularly d1-10 system plays an important role. Simultaneously the role of host - guest orientation has been considered the basis of photoluminescence. Acetate ion can be exchanged with iodide and sulphate ions. The decomposed product resulted the pure phase Mn doped zinc oxide are also reported.

  7. Novel optical waveguides by in-depth controlled electronic damage with swift ions

    Energy Technology Data Exchange (ETDEWEB)

    Olivares, J. [Instituto de Optica ' Daza de Valdes' , CSIC, C/Serrano 121, E-28006-Madrid (Spain)]. E-mail: j.olivares@io.cfmac.csic.es; Garcia-Navarro, A. [Centro de Microanalisis de Materiales (CMAM), UAM, Cantoblanco, E-28049-Madrid (Spain); Mendez, A. [Centro de Microanalisis de Materiales (CMAM), UAM, Cantoblanco, E-28049-Madrid (Spain); Agullo-Lopez, F. [Centro de Microanalisis de Materiales (CMAM), UAM, Cantoblanco, E-28049-Madrid (Spain); Depto. Fisica de Materiales (C-IV), UAM, E-28049-Madrid (Spain); Garcia, G. [Centro de Microanalisis de Materiales (CMAM), UAM, Cantoblanco, E-28049-Madrid (Spain); Garcia-Cabanes, A. [Depto. Fisica de Materiales (C-IV), UAM, E-28049-Madrid (Spain); Carrascosa, M. [Depto. Fisica de Materiales (C-IV), UAM, E-28049-Madrid (Spain)

    2007-04-15

    We review recent results on a novel method to modify crystalline dielectric materials and fabricate optical waveguides and integrated optics devices. It relies on irradiation with medium-mass high-energy ions (2-50 MeV) where the electronic stopping power is dominant over that one associated to nuclear collisions. By exploiting the processing capabilities of the method, novel optical structures can be achieved at moderate (10{sup 14} cm{sup -2}) and even low and ultralow (10{sup 12} cm{sup -2}) fluences. In particular, step-like waveguides with a high index jump {delta}n {approx} 0.1-0.2, guiding both ordinary and extraordinary modes, have been prepared with F and O ions (20 MeV) at moderate fluences. They present good non-linear and electrooptic perfomance and low losses. (1 dB/cm). Moreover, useful optical waveguiding has been also achieved at ultralow frequencies (isolated track regime), using Cl and Si ions (40-45 MeV). In this latter case, the individual amorphous nanotracks, whose radius increases with depth, create an effective optical medium causing optical trapping.

  8. Optomechanical Entanglement Between an Ion and an Optical Cavity Field

    Science.gov (United States)

    Bhattacherjee, Aranya B.

    2016-04-01

    I study an optomechanical system in which the mechanical motion of a single trapped ion is coupled to a cavity field for the realization of a strongly quantum correlated two-mode system. I show that for large pump intensities the steady state photon number exhibits bistable behaviour. I further analyze the occurrence of normal mode splitting (NMS) due to mixing of the fluctuations of the cavity field and the fluctuations of the ion motion which indicates a coherent energy exchange. I also find that in the parameter regime where NMS exists, the steady state of the system shows continuous variable entanglement. Such a two-mode optomechanical system can be used for the realization of continuous variable quantum information interfaces and networks.

  9. Demonstration of integrated microscale optics in surface-electrode ion traps

    CERN Document Server

    Merrill, J True; Landgren, David; Amini, Jason M; Wright, Kenneth; Doret, S Charles; Pai, C-S; Hayden, Harley; Killian, Tyler; Faircloth, Daniel; Brown, Kenneth R; Harter, Alexa W; Slusher, Richart E

    2011-01-01

    In ion trap quantum information processing, efficient fluorescence collection is critical for fast, high-fidelity qubit detection and ion-photon entanglement. The expected size of future many-ion processors require scalable light collection systems. We report on the development and testing of a microfabricated surface-electrode ion trap with an integrated high numerical aperture (NA) micromirror for fluorescence collection. When coupled to a low NA lens, the optical system is inherently scalable to large arrays of mirrors in a single device. We demonstrate stable trapping and transport of 40Ca+ ions over a 0.63 NA micromirror and observe a factor of 1.9 enhancement in photon collection compared to the planar region of the trap.

  10. Demonstration of integrated microscale optics in surface-electrode ion traps

    Energy Technology Data Exchange (ETDEWEB)

    True Merrill, J; Brown, Kenneth R [Schools of Chemistry and Biochemistry, Computational Science and Engineering, and Physics, Georgia Institute of Technology, Atlanta, GA 30332 (United States); Volin, Curtis; Landgren, David; Amini, Jason M; Wright, Kenneth; Charles Doret, S; Pai, C-S; Hayden, Harley; Killian, Tyler; Faircloth, Daniel; Harter, Alexa W; Slusher, Richart E, E-mail: curtis.volin@gtri.gatech.edu [Georgia Tech Research Institute, Atlanta, GA 30332 (United States)

    2011-10-15

    In ion trap quantum information processing, efficient fluorescence collection is critical for fast, high-fidelity qubit detection and ion-photon entanglement. The expected size of future many-ion processors requires scalable light collection systems. We report on the development and testing of a microfabricated surface-electrode ion trap with an integrated high-numerical aperture (NA) micromirror for fluorescence collection. When coupled to a low-NA lens, the optical system is inherently scalable to large arrays of mirrors in a single device. We demonstrate the stable trapping and transport of {sup 40}Ca{sup +} ions over a 0.63 NA micromirror and observe a factor of 1.9 enhancement of photon collection compared to the planar region of the trap. (paper)

  11. Optical properties and surface damage studies of crystalline silicon caused by swift iron ions

    Energy Technology Data Exchange (ETDEWEB)

    Dubey, S.K., E-mail: skdubey@physics.mu.ac.in

    2016-05-15

    p-Type silicon samples irradiated with 70 MeV {sup 56}Fe{sup 5+} ions for various fluences varying between 5 × 10{sup 12} and 4 × 10{sup 14} ions cm{sup −2} have been studied using spectroscopic ellipsometry and Fourier transform infrared spectroscopy. The microstructure of the irradiated samples was modeled from ellipsometric data, using a multilayer optical model and Bruggeman effective medium approximation. The values of pseudodielectric function, absorption coefficient and Penn gap energy were determined with respect to ion fluence. The effective medium analysis suggests that the superficial silicon layer can be explained as a mixture of crystalline and damaged silicon. The thickness of the damaged layer and percentage of voids present in the layer were found to increase with increase in the ion fluence. The effect of disorder on the interband optical spectra, especially on the critical point E{sub 1} at 3.4 eV was found to vary with ion fluence. A red shift in the critical point E{sub 1} with increasing ion fluence was observed. FTIR study showed of silicon samples irradiated with 70 MeV {sup 56}Fe{sup 5+} ions produced the oscillations in the spectral region 1000–400 cm{sup −1}. As irradiated sample showed more pronounced fringes, while contrast of the fringes and amplitude both were found to decrease with increase in depth.

  12. VO 2+ ions in zinc lead borate glasses studied by EPR and optical absorption techniques

    Science.gov (United States)

    Prakash, P. Giri; Rao, J. Lakshmana

    2005-09-01

    Electron paramagnetic resonance (EPR) and optical absorption spectra of vanadyl ions in zinc lead borate (ZnO-PbO-B 2O 3) glass system have been studied. EPR spectra of all the glass samples exhibit resonance signals characteristic of VO 2+ ions. The values of spin-Hamiltonian parameters indicate that the VO 2+ ions in zinc lead borate glasses were present in octahedral sites with tetragonal compression and belong to C 4V symmetry. The spin-Hamiltonian parameters g and A are found to be independent of V 2O 5 content and temperature but changing with ZnO content. The decrease in Δ g∥/Δ g⊥ value with increase in ZnO content indicates that the symmetry around VO 2+ ions is more octahedral. The decrease in intensity of EPR signal above 10 mol% of V 2O 5 is attributed to a fall in the ratio of the number of V 4+ ions ( N4) to the number of V 5+ ions ( N5). The number of spins ( N) participating in resonance was calculated as a function of temperature for VO 2+ doped zinc lead borate glass sample and the activation energy was calculated. From the EPR data, the paramagnetic susceptibility was calculated at various temperatures and the Curie constant was evaluated from the 1/ χ- T graph. The optical absorption spectra show single absorption band due to VO 2+ ions in tetragonally distorted octahedral sites.

  13. Development of emulsion track expansion techniques for optical-microscopy-observation of low-velocity ion tracks with ranges beyond optical resolution limit

    Energy Technology Data Exchange (ETDEWEB)

    Naka, T. [F-lab., Department of Physics, Nagoya University, Nagoya 464-8602 (Japan); Natsume, M. [F-lab., Department of Physics, Nagoya University, Nagoya 464-8602 (Japan)], E-mail: natsume@flab.phys.nagoya-u.ac.jp; Niwa, K.; Hoshino, K.; Nakamura, M.; Nakano, T.; Sato, O. [F-lab., Department of Physics, Nagoya University, Nagoya 464-8602 (Japan)

    2007-11-01

    We succeeded to observe tracks of low-velocity Kr ions, having originally ranges below optical resolution, in a fine grain nuclear emulsion with an optical microscope after expanding the emulsion along the incident direction. This opens up the possibility of tracking low-velocity nuclear recoils from massive dark matter particles using optical microscope scanning systems.

  14. Ion-exchanged diffractive elements in glass for substrate-mode optics.

    Science.gov (United States)

    Salmio, R P; Saarinen, J; Noponen, E

    1998-08-01

    We recently demonstrated the use of continuous-phase ion-exchanged diffractive elements in glass for free-space optics. We extend our design methods to substrate-mode optics, which permits compact packing of miniature-sized free-space optical systems. We designed one-dimensional gratings for equal-intensity 1 ? 3 and 1 ? 5 beam splitting, assuming both planar and conical incidence angles. An experimental demonstration of a 1 ? 3 beam splitter with a uniformity error of 3.4% is presented.

  15. Validation of two gridded soil moisture products over India with in-situ observations

    Science.gov (United States)

    Unnikrishnan, C. K.; George, John P.; Lodh, Abhishek; Maurya, Devesh Kumar; Mallick, Swapan; Rajagopal, E. N.; Mohandas, Saji

    2016-07-01

    Surface level soil moisture from two gridded datasets over India are evaluated in this study. The first one is the UK Met Office (UKMO) soil moisture analysis produced by a land data assimilation system based on Extended Kalman Filter method (EKF), which make use of satellite observation of Advanced Scatterometer (ASCAT) soil wetness index as well as the screen level meteorological observations. Second dataset is a satellite soil moisture product, produced by National Remote Sensing Centre (NRSC) using passive microwave Advanced Microwave Scanning Radiometer 2 measurements. In-situ observations of soil moisture from India Meteorological Department (IMD) are used for the validation of the gridded soil moisture products. The difference between these datasets over India is minimum in the non-monsoon months and over agricultural regions. It is seen that the NRSC data is slightly drier (0.05%) and UKMO soil moisture analysis is relatively wet during southwest monsoon season. Standard AMSR-2 satellite soil moisture product is used to compare the NRSC and UKMO products. The standard AMSR-2 and UKMO values are closer in monsoon season and AMSR-2 soil moisture is higher than UKMO in all seasons. NRSC and AMSR-2 showed a correlation of 0.83 (significant at 0.01 level). The probability distribution of IMD soil moisture observation peaks at 0.25 m3/m3, NRSC at 0.15 m3/m3, AMSR-2 at 0.25 m3/m3 and UKMO at 0.35 m3/m3 during June-September period. Validation results show UKMO analysis has better correlation with in-situ observations compared to the NRSC and AMSR-2 datasets. The seasonal variation in soil moisture is better represented in UKMO analysis. Underestimation of soil moisture during monsoon season over India in NRSC data suggests the necessity of incorporating the actual vegetation for a better soil moisture retrieval using passive microwave sensors. Both products have good agreement over bare soil, shrubs and grassland compared to needle leaf tree, broad leaf tree and

  16. Validation of two gridded soil moisture products over India with in-situ observations

    Indian Academy of Sciences (India)

    C K Unnikrishnan; John P George; Abhishek Lodh; Devesh Kumar Maurya; Swapan Mallick; E N Rajagopal; Saji Mohandas

    2016-07-01

    Surface level soil moisture from two gridded datasets over India are evaluated in this study. The firstone is the UK Met Office (UKMO) soil moisture analysis produced by a land data assimilation systembased on Extended Kalman Filter method (EKF), which make use of satellite observation of AdvancedScatterometer (ASCAT) soil wetness index as well as the screen level meteorological observations. Seconddataset is a satellite soil moisture product, produced by National Remote Sensing Centre (NRSC) usingpassive microwave Advanced Microwave Scanning Radiometer 2 measurements. In-situ observations ofsoil moisture from India Meteorological Department (IMD) are used for the validation of the gridded soilmoisture products. The difference between these datasets over India is minimum in the non-monsoonmonths and over agricultural regions. It is seen that the NRSC data is slightly drier (0.05%) and UKMOsoil moisture analysis is relatively wet during southwest monsoon season. Standard AMSR-2 satellitesoil moisture product is used to compare the NRSC and UKMO products. The standard AMSR-2 andUKMO values are closer in monsoon season and AMSR-2 soil moisture is higher than UKMO in allseasons. NRSC and AMSR-2 showed a correlation of 0.83 (significant at 0.01 level). The probabilitydistribution of IMD soil moisture observation peaks at 0.25 m^3/m^3, NRSC at 0.15 m^3/m^3, AMSR-2 at0.25 m3/m3 and UKMO at 0.35 m^3/m^3 during June–September period. Validation results show UKMOanalysis has better correlation with in-situ observations compared to the NRSC and AMSR-2 datasets.The seasonal variation in soil moisture is better represented in UKMO analysis. Underestimation of soilmoisture during monsoon season over India in NRSC data suggests the necessity of incorporating theactual vegetation for a better soil moisture retrieval using passive microwave sensors. Both productshave good agreement over bare soil, shrubs and grassland compared to needle leaf tree, broad leaf treeand urban land

  17. Effect of nitrogen ion implantation on the structural and optical properties of indium oxide thin films

    Energy Technology Data Exchange (ETDEWEB)

    Sethi, Riti; Aziz, Anver; Siddiqui, Azher M., E-mail: amsiddiqui@jmi.ac.in [Department of Physics, Jamia Millia Islamia, New Delhi-110025 (India); Kumar, Pravin [Inter University Accelerator Center, Aruna Asaf Ali Marg, New Delhi-110067 (India); Khan, Sameen Ahmed [Department of Mathematics and Sciences, College of Arts and Applied Sciences (CAAS) Dhofar University, Salalah, Sultanate of Oman (Oman)

    2016-06-10

    : We report here synthesis and subsequent nitrogen ion implantation of indium oxide (In{sub 2}O{sub 3}) thin films. The films were implanted with 25 keV N{sup +} beam for different ion doses between 3E15 to 1E16 ions/cm{sup 2}. The resulting changes in structural and optical properties were investigated using XRD, SEM-EDAX and UV-Vis Spectrometry. XRD studies reveal decrease in crystallite size from 20.06 to 12.42 nm with increase in ion dose. SEM micrographs show an increase in the grain size from 0.8 to 1.35 µm with increase in ion dose because of the agglomeration of the grains. Also, from EDAX data on pristine and N-implanted thin films the presence of indium and oxygen without any traces of impurity elements could be seen. However, at lower ion doses such as 3E15 and 5E15 ions/cm{sup 2}, no evidence of the presence of nitrogen ion was seen. However, for the ion dose of 1E16 ions/cm{sup 2}, evidence of presence of nitrogen can be seen in the EDAX data. Band gap calculations reveal a decrease in band gap from 3.54 to 3.38 eV with increasing ion dose. However, the band gap was found to again show an increase to 3.58 eV at the highest ion dose owing to quantum confinement effect.

  18. Beam optics optimization of a negative-ion sputter source

    Indian Academy of Sciences (India)

    F Osswald; R Rebmeister

    2002-11-01

    A negative-ion sputter source has been studied in order to increase the beam intensity delivered by the Vivitron tandem injector. The aim was to characterize the influence on the beam intensity of some factors related to the configuration of the source such as the shape of the target holder, the target surface topography and the anode/cathode voltage. The paper reports the results carried out by experimentation on a test facility and on the injector itself as well as the investigations performed with computer simulations.

  19. Structural and optical properties of vanadium ion-implanted GaN

    Science.gov (United States)

    Macková, A.; Malinský, P.; Jagerová, A.; Sofer, Z.; Klímová, K.; Sedmidubský, D.; Mikulics, M.; Lorinčík, J.; Veselá, D.; Böttger, R.; Akhmadaliev, S.

    2017-09-01

    The field of advanced electronic and optical devices searches for a new generation of transistors and lasers. The practical development of these novel devices depends on the availability of materials with the appropriate magnetic and optical properties, which is strongly connected to the internal morphology and the structural properties of the prepared doped structures. In this contribution, we present the characterisation of V ion-doped GaN epitaxial layers. GaN layers, oriented along the (0 0 0 1) crystallographic direction, grown by low-pressure metal-organic vapour-phase epitaxy (MOVPE) on c-plane sapphire substrates were implanted with 400 keV V+ ions at fluences of 5 × 1015 and 5 × 1016 cm-2. Elemental depth profiling was accomplished by Rutherford Backscattering Spectrometry (RBS) and Secondary Ion Mass Spectrometry (SIMS) to obtain precise information about the dopant distribution. Structural investigations are needed to understand the influence of defect distribution on the crystal-matrix recovery and the desired structural and optical properties. The structural properties of the ion-implanted layers were characterised by RBS-channelling and Raman spectroscopy to get a comprehensive insight into the structural modification of implanted GaN and to study the influence of subsequent annealing on the crystalline matrix reconstruction. Photoluminescence measurement was carried out to check the optical properties of the prepared structures.

  20. Optical properties of ion beam modified waveguide materials doped with erbium and silver

    NARCIS (Netherlands)

    Strohhöfer, C. (Christof)

    2002-01-01

    In the first part of this thesis we investigate codoping of erbium-doped waveguide materials with different ions in order to increase the efficiency of erbium-doped optical amplifiers. Codoping with ytterbium can overcome the limitations due to the small absorption cross section of Er3+ in Al2O3 at

  1. Potential of electric quadrupole transitions in radium isotopes for single-ion optical frequency standards

    NARCIS (Netherlands)

    Versolato, O. O.; Wansbeek, L. W.; Jungmann, K.; Timmermans, R. G. E.; Willmann, L.; Wilschut, H. W.

    2011-01-01

    We explore the potential of the electric quadrupole transitions 7s (2)S(1/2)-(6)d (2)D(3/2), 6d (2)D(5/2) in radium isotopes as single-ion optical frequency standards. The frequency shifts of the clock transitions due to external fields and the corresponding uncertainties are calculated. Several

  2. Optical and dielectric properties of ion beam irradiated Ag/polymethyl methacrylate nanocomposites.

    Science.gov (United States)

    Gavade, Chaitali; Singh, N L; Khanna, P K

    2014-08-01

    Changes in the dielectric, optical, structural and thermal properties of PMMA/silver nanocomposites of different concentrations of silver nanoparticles (5%, 10%, 15%) due to swift heavy ion irradiation were studied by means of impedance gain phase analyzer, UV-visible spectroscopy, X-ray diffraction and differential scanning calorimetry. Samples were irradiated with 120 MeV Si-ions at fluences of 1 x 10(11), 1 x 10(12) ions/cm2. Dependence of dielectric properties on frequency, ion beam fluence and filler concentration was studied. The results revealed the enhancement in dielectric properties after dopping nanoparticles and also upon irradiation. Optical properties like band gap was estimated for pure polymer and nanocomposite films from their optical absorption spectra in the wavelength region 200-800 nm. It was found that the band gap value shifted to lower energy (from 4.58 eV to 3.21 eV) on doping with silver nanoparticles. Differential scanning calorimetry analysis revealed a decrease in the glass transition temperature upon irradiation, which may be attributed to scissioning of polymer chain due to ion beam irradiation which is also confirmed with XRD analysis.

  3. All-Optical Broadband Excitation of the Motional State of Trapped Ions

    CERN Document Server

    Sheridan, Kevin; Gardner, Amy; Keller, Matthias

    2012-01-01

    We have developed a novel all-optical broadband scheme for exciting, amplifying and measuring the secular motion of ions in a radio frequency trap. Oscillation induced by yocto-Newton optical excitations have been coherently amplified to precisely control and measure the ion's secular motion. Requiring only laser line-of-sight, we have shown that the ion's oscillation amplitude can be precisely controlled. Our broadband excitation scheme generates coherent motion which is robust against variations in the secular frequency. Therefore, our scheme is ideal to excite the desired level of oscillatory motion under conditions where the secular frequency is evolving in time. Measuring the oscillation amplitude through Doppler velocimetry, we have characterized the experimental parameters and compared them with a molecular dynamics simulation which provides a complete description of the system.

  4. Tunable integrated optical filter made of a glass ion-exchanged waveguide and an electro-optic composite holographic grating.

    Science.gov (United States)

    d'Alessandro, Antonio; Donisi, Domenico; De Sio, Luciano; Beccherelli, Romeo; Asquini, Rita; Caputo, Roberto; Umeton, Cesare

    2008-06-23

    We report the fabrication and the optical characterization of a hybrid tunable integrated optical filter. It consists of a diffused ion-exchanged channel waveguide on a borosilicate glass substrate with a cover of the same glass to form a gap filled with a holographic grating. The grating morphology, called POLICRYPS (POlymer LIquid CRYstal Polymer Slices), is made of alternating stripes of polymer and liquid crystal acting as overlayer for the underneath waveguide. The filter structure includes aluminum coplanar electrodes to electrically control the grating properties, allowing the tunability of the filter. The electric driving power required to tune the filter obtained was in the range of submilliwatts due to the efficient liquid crystal electro-optic effect.

  5. Ion beam induced luminescence of germano-silicate optical fiber preform

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Hyunkyu; Kim, Jongyeol; Lee, Namho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Youngwoong; Han, Wontaek [Gwangju Institute of Science and Technology, Gwangju (Korea, Republic of); Markovic, Nikola; Jaksic, Milko [Ruder Boskovic Institute, Zagred (Croatia)

    2014-05-15

    When an optical fiber is exposed to radiation, the attenuation (RIA, Radiation Induced Attenuation) in the optical fiber (OF) is increased because of the color centers which deteriorate the transmission property and generate the absorption loss. In order to understand the radiation induced defect, Ion Beam induced luminescence (IBIL) was introduced to investigate it. IBIL technique is to analyze IR/VIS/UV luminescence related to ion beam interaction with outer shell electrons involved in chemical bonds and structure defects of target atoms. So IBIL is sensitive to its chemical composition and has been used in analysis of material characterization, geological samples and cultural heritage objects. In silica material, four O atoms are surrounding one Si atom in tetrahedral coordination. In this study, the influence of Copper (Cu) and Cerium (Ce) dopants to germano silica core optical fibers were investigated under proton irradiation at RBI using Ion Beam induced luminescence (IBIL) method. To understand the radiation induced defect of optical fibers, IBIL were tested to a germano-silica core fiber under 2 MeV proton irradiation. Although a Cu or Ce dopant was not detected by IBIL technique, the relation between the amount of radiation and luminescence can be established. This experiment showed a potential technique of studying the effects and behavior of additive elements for silica core fiber. To increase the radiation resistance of optical fibers, further investigations are needed, i. e. the proper additives and its contents and an interaction mechanism between Ge-related defects and additives.

  6. Correlation between the structural and optical properties of ion-assisted hafnia thin films

    Science.gov (United States)

    Scaglione, Salvatore; Sarto, Francesca; Alvisi, Marco; Rizzo, Antonella; Perrone, Maria R.; Protopapa, Maria L.

    2000-03-01

    The ion beam assistance during the film growth is one of the most useful method to obtain dense film along with improved optical and structural properties. Afnia material is widely used in optical coating operating in the UV region of the spectrum and its optical properties depend on the production method and the physical parameters of the species involved in the deposition process. In this work afnia thin films were evaporated by an e-gun and assisted during the growth process. The deposition parameters, ion beam energy, density of ions impinging on the growing film and the number of arrival atoms from the crucible, have been related to the optical and structural properties of the film itself. The absorption coefficient and the refractive index were measured by spectrophotometric technique while the microstructure has been studied by means of x-ray diffraction. A strictly correlation between the grain size, the optical properties and the laser damage threshold measurements at 248 nm was found for the samples deposited at different deposition parameters.

  7. Microstructured Optical Fiber-based Biosensors: Reversible and Nanoliter-Scale Measurement of Zinc Ions.

    Science.gov (United States)

    Heng, Sabrina; McDevitt, Christopher A; Kostecki, Roman; Morey, Jacqueline R; Eijkelkamp, Bart A; Ebendorff-Heidepriem, Heike; Monro, Tanya M; Abell, Andrew D

    2016-05-25

    Sensing platforms that allow rapid and efficient detection of metal ions would have applications in disease diagnosis and study, as well as environmental sensing. Here, we report the first microstructured optical fiber-based biosensor for the reversible and nanoliter-scale measurement of metal ions. Specifically, a photoswitchable spiropyran Zn(2+) sensor is incorporated within the microenvironment of a liposome attached to microstructured optical fibers (exposed-core and suspended-core microstructured optical fibers). Both fiber-based platforms retains high selectivity of ion binding associated with a small molecule sensor, while also allowing nanoliter volume sampling and on/off switching. We have demonstrated that multiple measurements can be made on a single sample without the need to change the sensor. The ability of the new sensing platform to sense Zn(2+) in pleural lavage and nasopharynx of mice was compared to that of established ion sensing methodologies such as inductively coupled plasma mass spectrometry (ICP-MS) and a commercially available fluorophore (Fluozin-3), where the optical-fiber-based sensor provides a significant advantage in that it allows the use of nanoliter (nL) sampling when compared to ICP-MS (mL) and FluoZin-3 (μL). This work paves the way to a generic approach for developing surface-based ion sensors using a range of sensor molecules, which can be attached to a surface without the need for its chemical modification and presents an opportunity for the development of new and highly specific ion sensors for real time sensing applications.

  8. Characterization of fluorescence collection optics integrated with a micro-fabricated surface electrode ion trap

    CERN Document Server

    Clark, Craig R; Ellis, A R; Hunker, Jeff; Kemme, Shanalyn A; Maunz, Peter; Tabakov, Boyan; Tigges, Chris; Stick, Daniel L

    2013-01-01

    One of the outstanding challenges for ion trap quantum information processing is to accurately detect the states of many ions in a scalable fashion. In the particular case of surface traps, geometric constraints make imaging perpendicular to the surface appealing for light collection at multiple locations with minimal cross-talk. In this report we describe an experiment integrating Diffractive Optic Elements (DOE's) with surface electrode traps, connected through in-vacuum multi-mode fibers. The square DOE's reported here were all designed with solid angle collection efficiencies of 3.58%; with all losses included a detection efficiency of 0.388% (1.02% excluding the PMT loss) was measured with a single Ca+ ion. The presence of the DOE had minimal effect on the stability of the ion, both in temporal variation of stray electric fields and in motional heating rates.

  9. Optical Filters Utilizing Ion Implanted Bragg Gratings in SOI Waveguides

    Directory of Open Access Journals (Sweden)

    M. P. Bulk

    2008-01-01

    Full Text Available The refractive index modulation associated with the implantation of oxygen or silicon into waveguides formed in silicon-on-insulator (SOI has been investigated to determine the feasibility of producing planar, implantation induced Bragg grating optical filters. A two-dimensional coupled mode theory-based simulation suggests that relatively short grating lengths, on the order of a thousand microns, can exhibit sufficient wavelength suppression, of >10 dB, using the implantation technique. Fabricated planar implanted slab-guided SOI waveguides demonstrated an extinction of −10 dB for TE modes and −6 dB for TM modes for the case of oxygen implantation. Extinctions of −5 dB and −2 dB have been demonstrated with silicon implantation.

  10. Effect of metal-ion doping on the optical properties of nanocrystalline ZnO thin films

    Science.gov (United States)

    Mendoza-Galván, A.; Trejo-Cruz, C.; Lee, J.; Bhattacharyya, D.; Metson, J.; Evans, P. J.; Pal, U.

    2006-01-01

    Optical properties of metal (Al, Ag, Sb, and Sn)-ion-implanted ZnO films have been studied by ultraviolet-visible spectroscopy and spectroscopic ellipsometric techniques. The effects of metal-ion doping on the optical band gap (Eg), refractive index (n), and extinction coefficient (k) of nanocrystalline ZnO films have been studied for the similar implantation dose of all the metal ions. The ellipsometric spectra of the ion-implanted samples could be well described by considering an air/roughness/ZnO-M (layer 1)/ZnO (layer 2)/glass model. The band gap of ZnO films increases with Al ion doping and decreases with doping of Ag, Sb, and Sn ions. The refractive index of ZnO films in the visible spectral region increases substantially on Sb and Sn ion doping, while it decreases to some extent with Al ion doping.

  11. Ion beam sputter deposition of Ag films: Influence of process parameters on electrical and optical properties, and average grain sizes

    Energy Technology Data Exchange (ETDEWEB)

    Bundesmann, C., E-mail: carsten.bundesmann@iom-leipzig.de; Feder, R.; Gerlach, J.W.; Neumann, H.

    2014-01-31

    Ion beam sputter deposition is used to grow several sets of Ag films under systematic variation of ion beam parameters, such as ion species and ion energy, and geometrical parameters, such as ion incidence angle and polar emission angle. The films are characterized concerning their thickness by profilometry, their electrical properties by 4-point-probe-measurements, their optical properties by spectroscopic ellipsometry, and their average grain sizes by X-ray diffraction. Systematic influences of the growth parameters on film properties are revealed. The film thicknesses show a cosine-like angular distribution. The electrical resistivity increases for all sets with increasing emission angle and is found to be considerably smaller for Ag films grown by sputtering with Xe ions than for the Ag films grown by sputtering with Ar ions. Increasing the ion energy or the ion incidence angle also increases the electrical resistivity. The optical properties, which are the result of free charge carrier absorption, follow the same trends. The observed trends can be partly assigned to changes in the average grain size, which are tentatively attributed to different energetic and angular distributions of the sputtered and back-scattered particles. - Highlights: • Ion beam sputter deposition under systematic variation of process parameters. • Film characterization: thickness, electrical, optical and structural properties. • Electrical resistivity changes considerably with ion species and polar emission angle. • Electrical and optical data reveal a strong correlation with grain sizes. • Change of film properties related to changing properties of film-forming particles.

  12. 700 keV Ni{sup +2} ions induced modification in structural, surface, magneto-optic and optical properties of ZnO thin films

    Energy Technology Data Exchange (ETDEWEB)

    Fiaz Khan, M. [Laser and Optronics Centre, Department of Physics, University of Engineering and Technology, Lahore (Pakistan); Siraj, K., E-mail: khurram.uet@gmail.com [Laser and Optronics Centre, Department of Physics, University of Engineering and Technology, Lahore (Pakistan); Anwar, M.S. [Department of Physics, Syed Babar Ali School of Science and Engineering, Lahore University of Management Sciences (LUMS), Opposite Sector U, D.H.A. Lahore 54792 (Pakistan); Irshad, M. [Laser and Optronics Centre, Department of Physics, University of Engineering and Technology, Lahore (Pakistan); Hussain, J. [National Centre for Physics, Islamabad (Pakistan); Faiz, H.; Majeed, S. [Laser and Optronics Centre, Department of Physics, University of Engineering and Technology, Lahore (Pakistan); Dosmailov, M.; Patek, J.; Pedarnig, J.D. [Institute of Applied Physics, Johannes Kepler University Linz (Austria); Rafique, M.S. [Laser and Optronics Centre, Department of Physics, University of Engineering and Technology, Lahore (Pakistan); Naseem, S. [Center of Excellence in Solid State Physics, University of Punjab, Lahore (Pakistan)

    2016-02-01

    Highlights: • 700 keV ion irradiation on ZnO thin films was done at different ion fluence. • XRD results showed improved crystallinity. • At lower fluence the microparticles were observed whereas ZnO micro rods were observed at higher fluences. • The Verdet constant and optical band gap energy of ZnO thin films are also well modified. - Abstract: We investigate the effect of 700 keV Ni{sup +2} ions irradiation at different ion fluences (1 × 10{sup 13}, 1 × 10{sup 14}, 2 × 10{sup 14}, 5 × 10{sup 14} ions/cm{sup 2}) on the structural, surface, magneto-optic and optical properties of ZnO thin films. The X-ray diffraction (XRD) results show improved crystallinity when ion fluence is increased to 2 × 10{sup 14} ions/cm{sup 2}, while deterioration is observed at the highest ion fluence of 5 × 10{sup 14} ions/cm{sup 2}. Scanning electron micrographs (SEM) show the formation of small grains at ion fluence 1 × 10{sup 13} ions/cm{sup 2}, micro-rods at fluences 1 × 10{sup 14} and 2 × 10{sup 14} ions/cm{sup 2} and ultimate fracturing of thin film surface at ion fluence 5 × 10{sup 14} ions/cm{sup 2}. Faraday rotation measurements are also performed and show a decrease in Verdet constant from 53 to 31 rad/(T-m) when irradiated at 1 × 10{sup 13} ions/cm{sup 2}, increasing up to 45 rad/(T-m) at 2 × 10{sup 14} ions/cm{sup 2}, and then decreasing again to 36 rad/(T-m) at 5 × 10{sup 14} ions/cm{sup 2}. The optical band gap energy of the films is determined using spectroscopic ellipsometry, which shows an increase in optical band gap energy (E{sub g}) from 3.04 eV to 3.19 eV when the fluence increases to 2 × 10{sup 14} ions/cm{sup 2} and a decrease to 3 eV at fluence 5 × 10{sup 14} ions/cm{sup 2}. We argue that these properties can be explained using ion heating effect of thin films.

  13. Optical properties of K9 glass waveguides fabricated by using carbon-ion implantation

    Science.gov (United States)

    Liu, Chun-Xiao; Wei, Wei; Fu, Li-Li; Zhu, Xu-Feng; Guo, Hai-Tao; Li, Wei-Nan; Lin, She-Bao

    2016-07-01

    K9 glass is a material with promising properties that make it attractive for optical devices. Ion implantation is a powerful technique to form waveguides with controllable depth and refractive index profile. In this work, optical planar waveguide structures were fabricated in K9 glasses by using 6.0-MeV C3+-ion implantation with a fluence of 1.0 × 1015 ions/cm2. The effective refractive indices of the guided modes were measured by using a prism-coupling system. The refractive index change in the ion-irradiated region was simulated by using the intensity calculation method. The modal intensity profile of the waveguide was calculated and measured by using the finite difference beam propagation method and the end-face coupling technique, respectively. The transmission spectra before and after the implantation showed that the main absorption band was not influenced by the low fluence dopants. The optical properties of the carbon-implanted K9 glass waveguides show promise for use as integrated photonic devices.

  14. Ra{sup +} ion trapping - atomic parity violation measurement and an optical clock

    Energy Technology Data Exchange (ETDEWEB)

    Mohanty, Amita; Dijck, Elwin A.; Nunez Portela, Mayerlin; Valappol, Nivedya; Boell, Oliver; Jungmann, Klaus; Onderwater, Cornelis G. G.; Schlesser, Sophie; Timmermans, Rob G.E.; Willmann, Lorenz; Wilschut, Hans W. [University of Groningen, FWN, Groningen (Netherlands)

    2014-07-01

    A single trapped Ra{sup +} ion has an excellent potential for a precision measurement of the Weinberg mixing angle at low momentum transfer and testing thereby the electroweak running. The absolute frequencies of the transition 7s {sup 2}S{sub 1/2}-7d{sup 2}D{sub 3/2} at wavelength 828 nm have been determined in {sup 212*214}Ra{sup +} to better than 19 MHz with laser spectroscopy on small samples of ions trapped in a linear Paul trap at the online facility TRIμP of KVI. The measurement of the Weinberg angle requires the localization of the ion within a fraction of an optical wavelength. The current experiments are focused on trapping and laser spectroscopy on a single Ba{sup +} as a precursor for Ra{sup +}. Work towards single ion trapping of Ra{sup +}, including the preparation of an offline {sup 223}Ra source is in progress. Most elements of the setup for single Ra+ ion parity measurement are also well suited for realizing a most stable optical clock.

  15. Optical field ionization of atoms and ions using ultrashort laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Fittinghoff, D.N.

    1993-12-01

    This dissertation research is an investigation of the strong optical field ionization of atoms and ions by 120-fs, 614-run laser pulses and 130-fs, 800-nm laser pulses. The experiments have shown ionization that is enhanced above the predictions of sequential tunneling models for He{sup +2}, Ne{sup +2} and Ar{sup +2}. The ion yields for He{sup +l}, Ne{sup +l} and Ar{sup +l} agree well with the theoretical predictions of optical tunneling models. Investigation of the polarization dependence of the ionization indicates that the enhancements are consistent with a nonsequential ionization mechanism in which the linearly polarized field drives the electron wavefunction back toward the ion core and causes double ionization through inelastic e-2e scattering. These investigations have initiated a number of other studies by other groups and are of current scientific interest in the fields of high-irradiance laser-matter interactions and production of high-density plasmas. This work involved: (1) Understanding the characteristic nature of the ion yields produced by tunneling ionization through investigation of analytic solutions for tunneling at optical frequencies. (2) Extensive characterization of the pulses produced by 614-nm and 800-ran ultrashort pulse lasers. Absolute calibration of the irradiance scale produced shows the practicality of the inverse problem--measuring peak laser irradiance using ion yields. (3) Measuring the ion yields for three noble gases using linear, circular and elliptical polarizations of laser pulses at 614-nm and 800-nm. The measurements are some of the first measurements for pulse widths as low as 120-fs.

  16. Large ion Coulomb crystals: A near-ideal medium for coupling optical cavity modes to matter

    DEFF Research Database (Denmark)

    Dantan, Aurélien; Albert, Magnus; Marler, Joan

    2009-01-01

    We present an investigation of the coherent coupling of various transverse field modes of an optical cavity to ion Coulomb crystals. The obtained experimental results, which include the demonstration of identical collective coupling rates for different transverse modes of a cavity field to ions...... in the same large Coulomb crystal, are in excellent agreement with theoretical predictions. The results furthermore suggest that Coulomb crystals in the future may serve as near-ideal media for high-fidelity multimode quantum information processing and communication purposes, including the generation...

  17. Precision measurement and compensation of optical stark shifts for an ion-trap quantum processor.

    Science.gov (United States)

    Häffner, H; Gulde, S; Riebe, M; Lancaster, G; Becher, C; Eschner, J; Schmidt-Kaler, F; Blatt, R

    2003-04-11

    Using optical Ramsey interferometry, we precisely measure the laser-induced ac-Stark shift on the S(1/2)-D(5/2) "quantum bit" transition near 729 nm in a single trapped 40Ca+ ion. We cancel this shift using an additional laser field. This technique is of particular importance for the implementation of quantum information processing with cold trapped ions. As a simple application we measure the atomic phase evolution during a n x 2 pi rotation of the quantum bit.

  18. Optical properties of lead borate glasses containing Dy{sup 3+} ions

    Energy Technology Data Exchange (ETDEWEB)

    Pisarska, Joanna [Department of Materials Science, Silesian University of Technology, Krasinskiego 8, 40-019 Katowice (Poland)], E-mail: Joanna.Pisarska@polsl.pl

    2009-07-15

    Optical properties of lead borate glasses containing Dy{sup 3+} ions were examined using absorption and luminescence measurements and theoretical calculations based on the Judd-Ofelt framework and the Inokuti-Hirayama model. The luminescence spectra show two characteristic bands at 480 and 573 nm, which are due to {sup 4}F{sub 9/2}-{sup 6}H{sub 15/2} (blue) and {sup 4}F{sub 9/2}-{sup 6}H{sub 13/2} (yellow) transitions of trivalent Dy{sup 3+} ions. The yellow/blue luminescence and its decay were analyzed as a function of activator concentration.

  19. Production yield of rare-earth ions implanted into an optical crystal

    Energy Technology Data Exchange (ETDEWEB)

    Kornher, Thomas, E-mail: t.kornher@physik.uni-stuttgart.de; Xia, Kangwei; Kolesov, Roman; Reuter, Rolf; Villa, Bruno; Wrachtrup, Jörg [3. Physikalisches Institut, Universität Stuttgart, 70569 Stuttgart (Germany); Kukharchyk, Nadezhda; Wieck, Andreas D. [Angewandte Festkörperphysik, Ruhr-Universität Bochum, 44780 Bochum (Germany); Siyushev, Petr [Universität Ulm, Institut für Quantenoptik, 89081 Ulm (Germany); Stöhr, Rainer [3. Physikalisches Institut, Universität Stuttgart, 70569 Stuttgart (Germany); Institute for Quantum Computing, University of Waterloo, Waterloo, Ontario N2L 3G1 (Canada); Schreck, Matthias [Experimentalphysik IV, Universität Augsburg, 86159 Augsburg (Germany); Becker, Hans-Werner [RUBION, Ruhr-Universität Bochum, 44780 Bochum (Germany)

    2016-02-01

    Rare-earth (RE) ions doped into desired locations of optical crystals might enable a range of novel integrated photonic devices for quantum applications. With this aim, we have investigated the production yield of cerium and praseodymium by means of ion implantation. As a measure, the collected fluorescence intensity from both implanted samples and single centers was used. With a tailored annealing procedure for cerium, a yield up to 53% was estimated. Praseodymium yield amounts up to 91%. Such high implantation yield indicates a feasibility of creation of nanopatterned rare-earth doping and suggests strong potential of RE species for on-chip photonic devices.

  20. Proposal for a simple integrated optical ion-exchange waveguide polarizer with a liquid crystal overlay

    Science.gov (United States)

    Wang, Pengfei; Semenova, Yuliya; Zheng, Jie; Wu, Qiang; Hatta, Agus Muhamad; Farrell, Gerald

    2011-02-01

    A simple, compact electro-optic polarizer based on an ion-exchanged glass channel waveguide covered with a nematic liquid crystal (LC) is proposed. A full-vectorial beam propagation method is employed to simulate this device for the first time. For the cases of zero and strong LC surface anchoring, the performance of the proposed polarizer under different applied voltages is analyzed numerically. Analysis indicates that surface anchoring of the liquid crystal is a key issue influencing the performance for the proposed optical polarizer device.

  1. EPR and optical absorption studies of Cr3+ ions in d-gluconic acid monohydrate.

    Science.gov (United States)

    Kripal, Ram; Singh, Pragya; Govind, Har

    2009-10-01

    EPR studies are carried out on Cr(3+) ions doped in d-gluconic acid monohydrate (C(6)H(12)O(7)*H(2)O) single crystals at 77 K. From the observed EPR spectra, the spin Hamiltonian parameters g, |D| and |E| are measured to be 1.9919, 349 (x 10(-4)) cm(-1) and 113 (x 10(-4)) cm(-1), respectively. The optical absorption of the crystal is also studied at room temperature. From the observed band positions, the cubic crystal field splitting parameter Dq (2052 cm(-1)) and the Racah interelectronic repulsion parameter B (653 cm(-1)) are evaluated. From the correlation of EPR and optical data the nature of bonding of Cr(3+) ion with its ligands is discussed.

  2. Quantum optics including noise reduction, trapped ions, quantum trajectories, and decoherence

    CERN Document Server

    Orszag, Miguel

    2016-01-01

    This new edition gives a unique and broad coverage of basic laser-related phenomena that allow graduate students, scientists and engineers to carry out research in quantum optics and laser physics. It covers quantization of the electromagnetic field, quantum theory of coherence, atom-field interaction models, resonance fluorescence, quantum theory of damping, laser theory using both the master equation and the Langevin theory, the correlated emission laser, input-output theory with applications to non-linear optics, quantum trajectories, quantum non-demolition measurements and generation of non-classical vibrational states of ions in a Paul trap. In this third edition, there is an enlarged chapter on trapped ions, as well as new sections on quantum computing and quantum bits with applications. There is also additional material included for quantum processing and entanglement. These topics are presented in a unified and didactic manner, each chapter is accompanied by specific problems and hints to solutions to...

  3. Magnetic-dipole transitions in highly charged ions as a basis of ultraprecise optical clocks.

    Science.gov (United States)

    Yudin, V I; Taichenachev, A V; Derevianko, A

    2014-12-05

    We evaluate the feasibility of using magnetic-dipole (M1) transitions in highly charged ions as a basis of an optical atomic clockwork of exceptional accuracy. We consider a range of possibilities, including M1 transitions between clock levels of the same fine-structure and hyperfine-structure manifolds. In highly charged ions these transitions lie in the optical part of the spectra and can be probed with lasers. The most direct advantage of our proposal comes from the low degeneracy of clock levels and the simplicity of atomic structure in combination with negligible quadrupolar shift. We demonstrate that such clocks can have projected fractional accuracies below the 10^{-20}-10^{-21} level for all common systematic effects, such as blackbody radiation, Zeeman, ac-Stark, and quadrupolar shifts.

  4. Optical properties of 3d-ions in crystals spectroscopy and crystal field analysis

    CERN Document Server

    Brik, Mikhail

    2013-01-01

    "Optical Properties of 3d-Ions in Crystals: Spectroscopy and Crystal Field Analysis" discusses spectral, vibronic and magnetic properties of 3d-ions in a wide range of crystals, used as active media for solid state lasers and potential candidates for this role. Crystal field calculations (including first-principles calculations of energy levels and absorption spectra) and their comparison with experimental spectra, the Jahn-Teller effect, analysis of vibronic spectra, materials science applications are systematically presented. The book is intended for researchers and graduate students in crystal spectroscopy, materials science and optical applications. Dr. N.M. Avram is an Emeritus Professor at the Physics Department, West University of Timisoara, Romania; Dr. M.G. Brik is a Professor at the Institute of Physics, University of Tartu, Estonia.

  5. Effective optical Faraday rotations of semiconductor EuS nanocrystals with paramagnetic transition-metal ions.

    Science.gov (United States)

    Hasegawa, Yasuchika; Maeda, Masashi; Nakanishi, Takayuki; Doi, Yoshihiro; Hinatsu, Yukio; Fujita, Koji; Tanaka, Katsuhisa; Koizumi, Hitoshi; Fushimi, Koji

    2013-02-20

    Novel EuS nanocrystals containing paramagnetic Mn(II), Co(II), or Fe(II) ions have been reported as advanced semiconductor materials with effective optical rotation under a magnetic field, Faraday rotation. EuS nanocrystals with transition-metal ions, EuS:M nanocrystals, were prepared by the reduction of the Eu(III) dithiocarbamate complex tetraphenylphosphonium tetrakis(diethyldithiocarbamate)europium(III) with transition-metal complexes at 300 °C. The EuS:M nanocrystals thus prepared were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM), inductively coupled plasma atomic emission spectroanalysis (ICP-AES), and a superconducting quantum interference device (SQUID) magnetometer. Enhanced Faraday rotations of the EuS:M nanocrystals were observed around 550 nm, and their enhanced spin polarization was estimated using electron paramagnetic resonance (EPR) measurements. In this report, the magneto-optical relationship between the Faraday rotation efficiency and spin polarization is discussed.

  6. TOWARDS 100% POLARIZATION IN THE OPTICALLY-PUMPED POLARIZED ION SOURCE.

    Energy Technology Data Exchange (ETDEWEB)

    ZELENSKI,A.; ALESSI, J.; KOKHANOVSKI, S.; KPONOU, A.; RITTER, B.J.; ZUBETS, V.

    2007-06-25

    The depolarization factors in the multi-step spin-transfer polarization technique and basic limitations on maximum polarization in the OPPIS (Optically-Pumped Polarized H{sup -} Ion Source) are discussed. Detailed studies of polarization losses in the RHIC OPPIS and the source parameters optimization resulted in the OPPIS polarization increase to 86-90%. This contributed to increasing polarization in the AGS and RHIC to 65-70%.

  7. Fused Silica Ion Trap Chip with Efficient Optical Collection System for Timekeeping, Sensing, and Emulation

    Science.gov (United States)

    2015-01-22

    sourcing, or in some ion trap applications, RF resonant detection. The walls of the high aspect slots and undercuts used to establish electrode...voltage test of these prototypes under vacuum did not result in any trace of breakdown (i.e. no observation of sparks or resonance jumps) even after...holes are characteristically conical . This geometry provides two benefits: it minimizes any limitation to the numerical aperture of the optics, and it

  8. Alkaline aluminum phosphate glasses for thermal ion-exchanged optical waveguide

    Science.gov (United States)

    Wang, Fei; Chen, Baojie; Pun, Edwin Yue Bun; Lin, Hai

    2015-04-01

    Alkaline aluminum phosphate glasses (NMAP) with excellent chemical durability for thermal ion-exchanged optical waveguide have been designed and investigated. The transition temperature Tg (470 °C) is higher than the ion-exchange temperature (390 °C), which is favorable to sustain the stability of the glass structure for planar waveguide fabrication. The effective diffusion coefficient De of K+-Na+ ion exchange in NMAP glasses is 0.110 μm2/min, indicating that ion exchange can be achieved efficiently in the optical glasses. Single-mode channel waveguide has been fabricated on Er3+/Yb3+ doped NMAP glass substrate by standard micro-fabrication and K+-Na+ ion exchange. The mode field diameter is 9.6 μm in the horizontal direction and 6.0 μm in the vertical direction, respectively, indicating an excellent overlap with a standard single-mode fiber. Judd-Ofelt intensity parameter Ω2 is 5.47 × 10-20 cm2, implying a strong asymmetrical and covalent environment around Er3+ in the optical glasses. The full width at half maximum and maximum stimulated emission cross section of the 4I13/2 → 4I15/2 are 30 nm and 6.80 × 10-21 cm2, respectively, demonstrating that the phosphate glasses are potential glass candidates in developing compact optoelectronic devices. Pr3+, Tm3+ and Ho3+ doped NMAP glasses are promising candidates to fabricate waveguide amplifiers and lasers operating at special telecommunication windows.

  9. Tailoring of the luminescent ions local environment in optical fibers, and applications

    CERN Document Server

    Dussardier, Bernard; Peterka, P

    2012-01-01

    The chapter is situated in the fields of fiber materials sciences and technologies (particularly dealing with the fiber glass compositions and luminescent ion doping, and transparent glass ceramic optical fibers), and applications such as fiber lasers and amplifiers. We propose to present a review of research activities on rare-earth (RE) and transition metals (TM) doped silica-based optical fibers, aiming at understanding theier spectral properties, and particularly some of their optical transitions that will allow interesting and alternative applications. Silica, as opposed to alternative, low temperature materials, is chosen for practical and economical reasons. Selected RE and TM ions are studied both as probes of their local environment and for their application potentials. In this chapter, we will focus on erbium (Er) ions for the potential spectral 'tailoring' of its gain curve at 1.55 $\\mu$m, thulium (Tm) as local environment probe along both near infrared transitions around 0.8 and 1.47 $\\mu$m, and c...

  10. Effect of disorder and defects in ion-implanted semiconductors optical and photothermal characterization

    CERN Document Server

    Willardson, R K; Christofides, Constantinos; Ghibaudo, Gerard

    1997-01-01

    Defects in ion-implanted semiconductors are important and will likely gain increased importance as annealing temperatures are reduced with successive IC generations. Novel implant approaches, such as MdV implantation, create new types of defects whose origin and annealing characteristics will need to be addressed. Publications in this field mainly focus on the effects of ion implantation on the material and the modification in the implanted layer after high temperature annealing. The editors of this volume and Volume 45 focus on the physics of the annealing kinetics of the damaged layer. An overview of characterization tehniques and a critical comparison of the information on annealing kinetics is also presented. Key Features * Provides basic knowledge of ion implantation-induced defects * Focuses on physical mechanisms of defect annealing * Utilizes electrical, physical, and optical characterization tools for processed semiconductors * Provides the basis for understanding the problems caused by the defects g...

  11. A virtual reality instrument: near-future perspective of computer simulations of ion optics

    Energy Technology Data Exchange (ETDEWEB)

    Veryovkin, Igor V. E-mail: verigo@anl.gov; Calaway, Wallis F.; Pellin, Michael J

    2004-02-21

    The method of accurate modeling of complex ion optical systems is presented. It combines using SIMION 3D{sup (c)} with external software generating input ion sets and processing results of ion trajectory simulations. This method was used to simulate time-of-flight (TOF) mass spectrometer of secondary neutrals SARISA (Surface Analysis by Resonance Ionization of Sputtered Atoms), and results of simulations were compared to results of the experiments. It is demonstrated that the accuracy of the presented modeling method is sufficient to reproduce experimental TOF (mass) spectra and dependencies of the instrument useful yield on sputtering and ionization conditions. A concept of 'virtual reality instrument' as a logical extension of the method is discussed.

  12. Ag clustering investigation in laser irradiated ion-exchanged glasses by optical and vibrational spectroscopy

    Science.gov (United States)

    Trave, E.; Cattaruzza, E.; Gonella, F.; Calvelli, P.; Quaranta, A.; Rahman, A.; Mariotto, G.

    2012-09-01

    Ion exchange process is widely used to dope silicate glass layers with silver for several applications, ranging from light waveguide to nanostructured composite glass fabrication. The silver-doped structure and its physical properties depend on the preparation parameters as well as on subsequent treatments. In particular, laser irradiation of the ion exchanged glasses has been demonstrated to be an effective tool to control cluster size and size distribution. Nevertheless, a complete comprehension of the basic phenomena and a systematic characterization of these systems are still lacking. In this paper, an extended optical characterization is presented for soda-lime glass slides, doped with silver by Ag+-Na+ ion exchange, thermally treated and irradiated with a Nd:YAG laser beam at different wavelengths, and for different energy density. The samples were characterized by various spectroscopic techniques, namely, optical absorption, photoluminescence and micro-Raman analysis. The availability of all these characterization techniques allowed pointing out a suitable scenario for the Ag clustering evolution as a function of the ion exchange, annealing and laser irradiation parameters.

  13. Energy band gap and optical transition of metal ion modified double crossover DNA lattices.

    Science.gov (United States)

    Dugasani, Sreekantha Reddy; Ha, Taewoo; Gnapareddy, Bramaramba; Choi, Kyujin; Lee, Junwye; Kim, Byeonghoon; Kim, Jae Hoon; Park, Sung Ha

    2014-10-22

    We report on the energy band gap and optical transition of a series of divalent metal ion (Cu(2+), Ni(2+), Zn(2+), and Co(2+)) modified DNA (M-DNA) double crossover (DX) lattices fabricated on fused silica by the substrate-assisted growth (SAG) method. We demonstrate how the degree of coverage of the DX lattices is influenced by the DX monomer concentration and also analyze the band gaps of the M-DNA lattices. The energy band gap of the M-DNA, between the lowest unoccupied molecular orbital (LUMO) and the highest occupied molecular orbital (HOMO), ranges from 4.67 to 4.98 eV as judged by optical transitions. Relative to the band gap of a pristine DNA molecule (4.69 eV), the band gap of the M-DNA lattices increases with metal ion doping up to a critical concentration and then decreases with further doping. Interestingly, except for the case of Ni(2+), the onset of the second absorption band shifts to a lower energy until a critical concentration and then shifts to a higher energy with further increasing the metal ion concentration, which is consistent with the evolution of electrical transport characteristics. Our results show that controllable metal ion doping is an effective method to tune the band gap energy of DNA-based nanostructures.

  14. Transparent aluminium nanowire electrodes with optical and electrical anisotropic response fabricated by defocused ion beam sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Repetto, Diego, E-mail: diegorepet@gmail.com; Giordano, Maria Caterina, E-mail: marinagiordano88@gmail.com; Martella, Christian, E-mail: christian.martella@gmail.com; Buatier de Mongeot, Francesco, E-mail: buatier@fisica.unige.it

    2015-02-01

    Highlights: • Self-organized Al nanowires were grown on glass substrates by ion beam sputtering. • Al nanowire pattern exhibit electrical and optical anisotropy. • Al NW pattern can be used as transparent electrodes for optoelectronic devices. - Abstract: Self-organized Al nanowire (NW) electrodes have been obtained by defocused Ion Beam Sputtering (IBS) of polycrystalline Al films grown by sputter deposition. The electrical sheet resistance of the electrode has been acquired in situ during ion bombardment of the samples, evidencing an increase of the electronic transport anisotropy as a function of ion fluence between the two directions parallel and orthogonal to the NWs axis. Optical spectra in transmission also show a large dichroism between the two directions, suggesting the role of localized plasmons in the UV spectral range. The results show that Al NW electrodes, prepared under experimental conditions which are compatible with those of conventional industrial coaters and implanters, could represent a low cost alternative to the transparent conductive oxides employed in optoelectronic devices.

  15. Carbon dots rooted agarose hydrogel hybrid platform for optical detection and separation of heavy metal ions.

    Science.gov (United States)

    Gogoi, Neelam; Barooah, Mayuri; Majumdar, Gitanjali; Chowdhury, Devasish

    2015-02-11

    A robust solid sensing platform for an on-site operational and accurate detection of heavy metal is still a challenge. We introduce chitosan based carbon dots rooted agarose hydrogel film as a hybrid solid sensing platform for detection of heavy metal ions. The fabrication of the solid sensing platform is centered on simple electrostatic interaction between the NH3+ group present in the carbon dots and the OH- groups present in agarose. Simply on dipping the hydrogel film strip into the heavy metal ion solution, in particular Cr6+, Cu2+, Fe3+, Pb2+, Mn2+, the strip displays a color change, viz., Cr6+→yellow, Cu2+→blue, Fe3+→brown, Pb2+→white, Mn2+→tan brown. The optical detection limit of the respective metal ion is found to be 1 pM for Cr6+, 0.5 μM for Cu2+, and 0.5 nM for Fe3+, Pb2+, and Mn2+ by studying the changes in UV-visible reflectance spectrum of the hydrogel film. Moreover, the hydrogel film finds applicability as an efficient filtration membrane for separation of these quintet heavy metal ions. The strategic fundamental feature of this sensing platform is the successful capability of chitosan to form colored chelates with transition metals. This proficient hybrid hydrogel solid sensing platform is thus the most suitable to employ as an on-site operational, portable, cheap colorimetric-optical detector of heavy metal ion with potential skill in their separation. Details of the possible mechanistic insight into the colorimetric detection and ion separation are also discussed.

  16. Focussed ion beam machined cantilever aperture probes for near-field optical imaging.

    Science.gov (United States)

    Jin, E X; Xu, X

    2008-03-01

    Near-field optical probe is the key element of a near-field scanning optical microscopy (NSOM) system. The key innovation in the first two NSOM experiments (Pohl et al., 1984; Lewis et al., 1984) is the fabrications of a sub-wavelength optical aperture at the apex of a sharply pointed transparent probe tip with a thin metal coating. This paper discusses the routine use of focussed ion beam (FIB) to micro-machine NSOM aperture probes from the commercial silicon nitride cantilevered atomic force microscopy probes. Two FIB micro-machining approaches are used to form a nanoaperture of controllable size and shape at the apex of the tip. The FIB side slicing produces a silicon nitride aperture on the flat-end tips with controllable sizes varying from 120 nm to 30 nm. The FIB head-on drilling creates holes on the aluminium-coated tips with sizes down to 50 nm. Nanoapertures in C and bow tie shapes can also be patterned using the FIB head-on milling method to possibly enhance the optical transmission. A transmission-collection NSOM system is constructed from a commercial atomic force microscopy to characterize the optical resolution of FIB-micro-machined aperture tips. The optical resolution of 78 nm is demonstrated by an aperture probe fabricated by FIB head-on drilling. Simultaneous topography imaging can also be realized using the same probe. By mapping the optical near-field from a bow-tie aperture, optical resolution as small as 59 nm is achieved by an aperture probe fabricated by the FIB side slicing method. Overall, high resolution and reliable optical imaging of routinely FIB-micro-machined aperture probes are demonstrated.

  17. Influence of ion/atom arrival ratio on structure and optical properties of AlN films by ion beam assisted deposition

    Energy Technology Data Exchange (ETDEWEB)

    Meng, Jian-ping [Department of Energy Material and Technology, General Research Institute for Nonferrous Metals, Beijing 100088 (China); School of Engineering and Technology, China University of Geosciences, Beijing 100083 (China); Fu, Zhi-qiang, E-mail: fuzq@cugb.edu.cn [School of Engineering and Technology, China University of Geosciences, Beijing 100083 (China); Liu, Xiao-peng [Department of Energy Material and Technology, General Research Institute for Nonferrous Metals, Beijing 100088 (China); Yue, Wen; Wang, Cheng-biao [School of Engineering and Technology, China University of Geosciences, Beijing 100083 (China)

    2014-10-30

    Highlights: • AlN films were fabricated by dual ion beam sputtering. • Chemical bond status and phase composition of the films were studied by XPS and XRD. • Optical constants were measured by spectroscopic ellipsometry. • Influence of ion/atom arrival ratio on the films was studied. - Abstract: In order to improve the optical properties of AlN films, the influence of the ion/atom arrival ratio on the structure and optical characteristics of AlN films deposited by dual ion beam sputtering was studied by using X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, spectroscopic ellipsometry and UV–vis spectroscopy. The films prepared at the ion/atom arrival ratio of 1.4 are amorphous while the crystalline quality is improved with the increase of the ion/atom arrival ratio. The films deposited at the ion/atom arrival ratio of no less than 1.8 have an approximately stoichiometric ratio and mainly consist of aluminum nitride with little aluminum oxynitride, while metallic aluminum component appears in the films deposited at the ion/atom arrival ratio of 1.4. When the ion/atom arrival ratio is not less than 1.8, films are smooth, high transmitting and dense. The films prepared with high ion/atom arrival ratio (≥1.8) display the characteristic of a dielectric. The films deposited at the ion/atom arrival ratio of 1.4 are coarse, opaque and show characteristic of cermet.

  18. Optical switches and triggers for the manipulation of ion channels and pores.

    Science.gov (United States)

    Gorostiza, Pau; Isacoff, Ehud

    2007-10-01

    Like fluorescence sensing techniques, methods to manipulate proteins with light have produced great advances in recent years. Ion channels have been one of the principal protein targets of photoswitched manipulation. In combination with fluorescence detection of cell signaling, this has enabled non-invasive, all-optical experiments on cell and tissue function, both in vitro and in vivo. Optical manipulation of channels has also provided insights into the mechanism of channel function. Optical control elements can be classified according to their molecular reversibility as non-reversible phototriggers where light breaks a chemical bond (e.g. caged ligands) and as photoswitches that reversibly photoisomerize. Synthetic photoswitches constitute nanoscale actuators that can alter channel function using three different strategies. These include (1) nanotoggles, which are tethered photoswitchable ligands that either activate channels (agonists) or inhibit them (blockers or antagonists), (2) nanokeys, which are untethered (freely diffusing) photoswitchable ligands, and (3) nanotweezers, which are photoswitchable crosslinkers. The properties of such photoswitches are discussed here, with a focus on tethered photoswitchable ligands. The recent literature on optical manipulation of ion channels is reviewed for the different channel families, with special emphasis on the understanding of ligand binding and gating processes, applications in nanobiotechnology, and with attention to future prospects in the field.

  19. Quantum Optics Including Noise Reduction, Trapped Ions, Quantum Trajectories, and Decoherence

    CERN Document Server

    Orszag, Miguel

    2008-01-01

    Quantum Optics gives a very broad coverage of basic laser-related phenomena that allow scientist and engineers to carry out research in quantum optics and laser physics. It covers quantization of the electromagnetic field, quantum theory of coherence, atom-field interaction models, resonance fluorescence, quantum theory of damping, laser theory using both the master equation and the Langevin theory, the correlated emission laser, input-output theory with applications to non-linear optics, quantum trajectories, quantum non-demolition measurements and generation of non-classical vibrational states of ions in a Paul trap. In this second edition, there is an enlarged chapter on decoherence, as well as additional material dealing with elements of quantum computation, entanglement of pure and mixed states as well as a chapter on quantum copying and processors. These topics are presented in a unified and didactic manner. The presentation of the book is clear and pedagogical; it balances the theoretical aspect of qua...

  20. Effect of ion and electron beam irradiation on surface morphology and optical properties of PVA

    Institute of Scientific and Technical Information of China (English)

    HM Eyssa; MO sman; SAK andil; MMA bdelrahman

    2015-01-01

    Polyvinyl alcohol (PVA) is a well-known friendly polymer for paper-making, textiles, and a variety of coat-ings, biomedical applications such as artificial pancreas, synthetic vitreous body, wound dressing, artificial skin, and cardiovascular device. In this paper, ion/electron beam is employed to get insight into the irradiation effect on surface morphology and optical properties of PVA polymer. UV-Vis spectra are recorded to investigate the effect of induced defects on the optical band gap and the formed carbon clusters size. Scanning electron microscopy (SEM) is used to relate and investigate surface morphology and optical properties of the target poly-mer with different doses (15, 30 and 60 min). Also, PVA polymer is subjected to theoretical studies by using semi-empirical PM7 quantum chemical method.

  1. Magneto-optical spectroscopy of Yb{sup 3+} ions in huntite structure

    Energy Technology Data Exchange (ETDEWEB)

    Sukhachev, A.L. [L.V. Kirensky Institute of Physics, Siberian Branch Russian Academy of Sciences, 660036 Krasnoyarsk (Russian Federation); Malakhovskii, A.V., E-mail: malakha@iph.krasn.r [L.V. Kirensky Institute of Physics, Siberian Branch Russian Academy of Sciences, 660036 Krasnoyarsk (Russian Federation); Edelman, I.S.; Zabluda, V.N.; Temerov, V.L.; Makievskii, I.Ya. [L.V. Kirensky Institute of Physics, Siberian Branch Russian Academy of Sciences, 660036 Krasnoyarsk (Russian Federation)

    2010-01-15

    We report the first measurements of magnetic circular dichroism (MCD) and magneto-optical activity (ratio of zero moments of MCD and absorption bands) of Yb{sup 3+} ion in the trigonal single crystals Yb{sub x}Tm{sub 1-x}Al{sub 3}(BO{sub 3}){sub 4} as a function of temperature in the range of 100-293 K. Magneto-optical activity follows the Curie-Weiss law with the Weiss constant theta=-55 K for Yb{sub 0.1}Tm{sub 0.9}Al{sub 3}(BO{sub 3}){sub 4} crystal. The value and origin of the magneto-optical activity is theoretically analyzed.

  2. Cu Ions Irradiation Impact on Structural and Optical Properties of GaN Thin Film

    Science.gov (United States)

    Shah, A.; Husnain, G.; Ahmad, Ishaq; Mahmood, Arshad

    2013-03-01

    Epitaxial grown Gallium nitride (GaN) thin film on sapphire was irradiated with Cu ions at various fluences (5×1014, 1 ×1015 and 5×1015cm-2). The level of lattice disorder, as measured by Rutherford backscattering spectrometry and channeling (RBS/C), gradually increases with the increasing of ions fluence. Lattice amorphization is observed for the sample irradiated with fluence of 5×1015cm-2 which is also confirmed by X-ray diffractometer (XRD) analysis. It was found that both Raman modes of GaN layer clearly shifted with Cu+ fluences. Both Raman and X-ray analyses explore that Cu atom substituted into Ga sites. Atomic force microscopy (AFM) images show the irradiated GaN surface roughness increases with the increasing ions fluence. The UV-visible transmittance spectrum and ellipsometric measurements show a decrease in the band gap value after irradiation of Cu ions in the GaN film. Moreover, the optical constants (n and k) of the films vary with the increasing of Cu ion fluences.

  3. Optical absorption and fluorescent behaviour of titanium ions in silicate glasses

    Indian Academy of Sciences (India)

    Manoj Kumar; Aman Uniyal; A P S Chauhan; S P Singh

    2003-04-01

    Titanium in normal melting conditions in air atmosphere present as Ti4+ ion in basic silicate glasses exhibited an ultra-violet cut-off in silicate glasses, viz. soda–magnesia–silica, soda–magnesia–lime–silica and soda–lime–silica glasses. This indicates that Ti4+ ion can be a good replacement for Ce4+ ion in producing UV-absorbing silicate glasses for commercial applications. The wavelength maxima at which the infinite absorption takes place in glasses was found to be around 310 nm against Ti-free blank glass in UV-region. The mechanism of electronic transition from O2- ligands to Ti4+ ion was suggested as L $\\rightarrow$ M charge transfer. The low energy tails of the ultra-violet cut-off were found to obey Urbach’s rule in the optical range 360–500 nm. The fluorescence spectra of these glasses were also studied and based on the radiative fluorescent properties it was suggested that the soda–lime–silica glass containing Ti4+ ion with greater emission crosssection would emit a better fluorescence than the corresponding soda–magnesia–lime–silica and soda–magnesia–silica glasses. The shift of emission wavelengths maxima towards longer wavelength in titania introduced silicate glasses was observed on replacement of MgO by CaO which may be attributed due to an increase in basicity of the glass system.

  4. Selective detection of mercury (II) ion using nonlinear optical properties of gold nanoparticles.

    Science.gov (United States)

    Darbha, Gopala Krishna; Singh, Anant Kumar; Rai, Uma Shanker; Yu, Eugene; Yu, Hongtao; Chandra Ray, Paresh

    2008-06-25

    Contamination of the environment with heavy metal ions has been an important concern throughout the world for decades. Driven by the need to detect trace amounts of mercury in environmental samples, this article demonstrates for the first time that nonlinear optical (NLO) properties of MPA-HCys-PDCA-modified gold nanoparticles can be used for rapid, easy and reliable screening of Hg(II) ions in aqueous solution, with high sensitivity (5 ppb) and selectivity over competing analytes. The hyper Rayleigh scattering (HRS) intensity increases 10 times after the addition of 20 ppm Hg(2+) ions to modified gold nanoparticle solution. The mechanism for HRS intensity change has been discussed in detail using particle size-dependent NLO properties as well as a two-state model. Our results show that the HRS assay for monitoring Hg(II) ions using MPA-HCys-PDCA-modified gold nanoparticles has excellent selectivity over alkali, alkaline earth (Li(+), Na(+), K(+), Mg(2+), Ca(2+)), and transition heavy metal ions (Pb(2+), Pb(+), Mn(2+), Fe(2+), Cu(2+), Ni(2+), Zn(2+), Cd(2+)).

  5. Analysis of thermal radiation in ion traps for optical frequency standards

    CERN Document Server

    Doležal, Miroslav; Nisbet-Jones, Peter B R; King, Steven A; Jones, Jonathan M; Klein, Hugh A; Gill, Patrick; Lindvall, Thomas; Wallin, Anders E; Merimaa, Mikko; Tamm, Christian; Sanner, Christian; Huntemann, Nils; Scharnhorst, Nils; Leroux, Ian D; Schmidt, Piet O; Burgermeister, Tobias; Mehlstäubler, Tanja E; Peik, Ekkehard

    2015-01-01

    In many of the high-precision optical frequency standards with trapped atoms or ions that are under development to date, the AC Stark shift induced by thermal radiation leads to a major contribution to the systematic uncertainty. We present an analysis of the inhomogeneous thermal environment experienced by ions in various types of ion traps. Finite element models which allow the determination of the temperature of the trap structure and the temperature of the radiation were developed for 5 ion trap designs, including operational traps at PTB and NPL and further optimized designs. Models were refined based on comparison with infrared camera measurement until an agreement of better than 10% of the measured temperature rise at critical test points was reached. The effective temperature rises of the radiation seen by the ion range from 0.8 K to 2.1 K at standard working conditions. The corresponding fractional frequency shift uncertainties resulting from the uncertainty in temperature are in the 10-18 range for ...

  6. Influence of Kilo-Electron Oxygen Ion Irradiation on Structural, Electrical and Optical Properties of CdTe Thin Films

    Science.gov (United States)

    Honey, Shehla; Thema, F. T.; Bhatti, M. T.; Ishaq, A.; Naseem, Shahzad; Maaza, M.

    2016-09-01

    In this paper, effect of oxygen (O+) ion irradiation on the properties of polycrystalline cubic structure CdTe thin films has been investigated. CdTe thin films were irradiated with O+ ions of energy 80keV at different fluence ranging from 1×1015 to 5×1016 ion/cm2 at room temperature. At 1×1015 ion/cm2 O+ ions fluence, the CdTe structure was maintained while XRD peaks of cubic phase were shifted toward lower angles. At 5×1016 ion/cm2 O+ ions fluence, cubic structure of CdTe thin films was transformed into hexagonal structure. In addition, electrical resistivity and optical bandgap were decreased with increasing O+ ion beam irradiation.

  7. Ag clustering investigation in laser irradiated ion-exchanged glasses by optical and vibrational spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Trave, E., E-mail: enrico.trave@unive.it [Department of Molecular Sciences and Nanosystems, Ca' Foscari University of Venezia, Dorsoduro 2137, I-30123 Venezia (Italy); Cattaruzza, E.; Gonella, F.; Calvelli, P. [Department of Molecular Sciences and Nanosystems, Ca' Foscari University of Venezia, Dorsoduro 2137, I-30123 Venezia (Italy); Quaranta, A. [Department of Materials Engineering and Industrial Technologies, University of Trento, via Mesiano 77, I-38050 Povo (Italy); Rahman, A.; Mariotto, G. [Department of Computer Science, University of Verona, Strada le Grazie 15, 37134 Verona (Italy)

    2012-09-15

    Highlights: Black-Right-Pointing-Pointer We modify the properties of Ag{sup +} exchanged glasses by thermal and laser treatment. Black-Right-Pointing-Pointer The induced microstructural changes are analyzed by optical and Raman spectroscopy. Black-Right-Pointing-Pointer Ag-based species in the glass show a peculiar PL activity in the UV-Vis range. Black-Right-Pointing-Pointer Raman and OA analysis allow for determining the Ag cluster size evolution. Black-Right-Pointing-Pointer Laser processing leads to different cluster formation and fragmentation mechanisms. - Abstract: Ion exchange process is widely used to dope silicate glass layers with silver for several applications, ranging from light waveguide to nanostructured composite glass fabrication. The silver-doped structure and its physical properties depend on the preparation parameters as well as on subsequent treatments. In particular, laser irradiation of the ion exchanged glasses has been demonstrated to be an effective tool to control cluster size and size distribution. Nevertheless, a complete comprehension of the basic phenomena and a systematic characterization of these systems are still lacking. In this paper, an extended optical characterization is presented for soda-lime glass slides, doped with silver by Ag{sup +}-Na{sup +} ion exchange, thermally treated and irradiated with a Nd:YAG laser beam at different wavelengths, and for different energy density. The samples were characterized by various spectroscopic techniques, namely, optical absorption, photoluminescence and micro-Raman analysis. The availability of all these characterization techniques allowed pointing out a suitable scenario for the Ag clustering evolution as a function of the ion exchange, annealing and laser irradiation parameters.

  8. Damage and deuterium retention in LiAlO 2 single crystals irradiated with deuterium ions using ion-beam techniques and optical absorption measurements

    Science.gov (United States)

    Katsui, H.; Nagata, S.; Tsuchiya, B.; Zhao, M.; Shikama, T.

    2011-10-01

    Ion beam analysis techniques and optical absorption measurements were employed to quantitatively examine the damage and deuterium retention in LiAlO 2 single crystals irradiated with 10 keV D2+. Rutherford backscattering spectrometry in channeling geometry revealed that the lattice atoms were disordered by the incident deuterium ions in the ratio O/Al of 2.5. Elastic recoil detection analysis showed that all the incident deuterium ions were retained near the end of their trajectories with a maximum concentration of 0.7 D/Al at room temperature. The depth profiles of the disordered atoms were nearly identical to those of the retained deuterium atoms. The release of the retained deuterium atoms and the annihilation of the ion-induced color centers, which contributed to an optical absorption band at 5.25 eV, were observed in the same temperature range. A correlation was established between the oxygen vacancies and the retained deuterium atoms.

  9. Electron Paramagnetic Resonance and Optical Absorption Studies on Copper Ions in Mixed Alkali Cadmium Phosphate Glasses

    Institute of Scientific and Technical Information of China (English)

    G.Giridhar; M.Rangacharyulu; R.V.S.S.N.Ravikumar; P.Sambasiva Rao

    2009-01-01

    Electron paramagnetic resonance (EPR) and optical absorption studies were carried out at room temperature on copper doped mixed alkali cadmium phosphate (LiNaCdP) glasses to understand the nature and symmetry of dopant. Three samples with varying concentrations of alkali ions have been prepared. The spin Hamiltonian parameters obtained from room temperature EPR spectra are: g||=2.437, g⊥=2.096, A||=117×10-4 cm-1, A⊥=26×10-4 cm-1 for LiNaCdP1, g||=2.441, g⊥=2.088, A||=121×10-4 cm-1, A⊥=25×10-4 cm-1 for LiNaCdP2 and g||=2.433, g⊥=2.096, A||=125×10-4 cm-1, A⊥=32×10-4 cm-1 for LiNaCdP3. These EPR results indicate that the dopant Cu2+ ion enters the glass matrix into a tetragonally elongated octahedral site. The bonding parameters evaluated by correlating optical and EPR data suggest that bonding between the central metal ion and ligands is partially covalent. The mixed alkali effect in cadmium phosphate glasses was reported.

  10. EPR and optical absorption studies of vanadyl ions in potassium oxalate monohydrate

    Energy Technology Data Exchange (ETDEWEB)

    Kripal, Ram [Department of Physics, University of Allahabad, Allahabad 211002 (India)]. E-mail: ram_kripal2001@rediffmail.com; Maurya, Manju [Department of Physics, University of Allahabad, Allahabad 211002 (India)]. E-mail: mmanju8@yahoo.co.in; Govind, Har [Department of Electronics, Ewing Christian College, Allahabad 211003 (India)

    2007-04-15

    Electron paramagnetic resonance (EPR) studies are reported on vanadyl (VO{sup 2+}) ions in potassium oxalate monohydrate (POM) single crystals at room temperature. The results indicate that the paramagnetic impurity takes up an interstitial site in the lattice. The angular variation of EPR spectra in three mutually perpendicular planes are used to determine the spin Hamiltonian parameters and the values obtained are: g{sub x} =2.0153{+-}0.0002, g{sub y} =1.9489{+-}0.0002, g{sub z} =1.9155{+-}0.0002 and A{sub x} =(63{+-}2)x10{sup -4} cm{sup -1}, A{sub y} =(92{+-}2)x10{sup -4} cm{sup -1}, A{sub z} =(193{+-}2)x10{sup -4} cm{sup -1}. The optical absorption spectrum of VO{sup 2+} ions in the crystal lattice is also studied at room temperature. The characteristic spectrum of the VO{sup 2+} ions has four absorption bands. The band positions are calculated using the energy expressions and compared with the observed values to confirm the transitions. The analysis of the spectrum indicates that the first three bands correspond to d-d transitions and the last band is probably charge transfer band. Crystal field parameter (Dq) and tetragonal parameters (Ds and Dt) are also evaluated. From optical and EPR data various bonding parameters are obtained and nature of bonding in the crystal is discussed.

  11. The structural and optical properties of metal ion-implanted GaN

    Science.gov (United States)

    Macková, A.; Malinský, P.; Sofer, Z.; Šimek, P.; Sedmidubský, D.; Veselý, M.; Böttger, R.

    2016-03-01

    The practical development of novel optoelectronic materials with appropriate optical properties is strongly connected to the structural properties of the prepared doped structures. We present GaN layers oriented along the (0 0 0 1) crystallographic direction that have been grown by low-pressure metal-organic vapour-phase epitaxy (MOVPE) on sapphire substrates implanted with 200 keV Co+, Fe+ and Ni+ ions. The structural properties of the ion-implanted layers have been characterised by RBS-channelling and Raman spectroscopy to obtain a comprehensive insight into the structural modification of implanted GaN layers and to study the subsequent influence of annealing on crystalline-matrix recovery. Photoluminescence was measured to control the desired optical properties. The post-implantation annealing induced the structural recovery of the modified GaN layer depending on the introduced disorder level, e.g. depending on the ion implantation fluence, which was followed by structural characterisation and by the study of the surface morphology by AFM.

  12. Laser system for Doppler cooling of ytterbium ion in an optical frequency standard

    Energy Technology Data Exchange (ETDEWEB)

    Chepurov, S V; Lugovoy, A A; Kuznetsov, S N [Institute of Laser Physics, Siberian Branch, Russian Academy of Sciences, Novosibirsk (Russian Federation)

    2014-06-30

    A laser system for Doppler cooling of ytterbium ion on the {sup 2}S{sub 1/2} → {sup 2}P{sub 1/2} transition in a single-ion optical frequency standard is developed. The second harmonic of a semiconductor laser with a wavelength of 739 nm is used for cooling. The laser frequency is doubled in a nonlinear BiBO crystal embedded in a ring resonator, which also serves as a reference for laser frequency stabilisation. Second-harmonic power of ∼100 μW is generated at a wavelength of 369.5 nm. Diode laser radiation is modulated by an electro-optic modulator at 14.75 GHz to generate a sideband exciting the {sup 2}S{sub 1/2} (F = 0) → {sup 2}P{sub 1/2} (F = 1) hyperfine component of the cooling transition that is not excited by resonant cooling light. The sideband relative intensity of a few percent proved to be sufficient to reduce the ion dwelling time in the {sup 2}S{sub 1/2} (F = 0) state to less than 10{sup -4} s and increase the cooling efficiency. (extreme light fields and their applications)

  13. Study of optical properties of swift heavy ion irradiated gallium antimonide

    Energy Technology Data Exchange (ETDEWEB)

    Dubey, S.K. [Department of Physics, University of Mumbai, Vidyanagari Campus, Santacruz (E), Mumbai 400 098 (India)]. E-mail: skdubey@physics.mu.ac.in; Dubey, R.L. [Department of Physics, University of Mumbai, Vidyanagari Campus, Santacruz (E), Mumbai 400 098 (India); Yadav, A.D. [Department of Physics, University of Mumbai, Vidyanagari Campus, Santacruz (E), Mumbai 400 098 (India); Jadhav, V. [Department of Physics, University of Mumbai, Vidyanagari Campus, Santacruz (E), Mumbai 400 098 (India); Rao, T.K. Gundu [Regional Sophisticated Instrumentation Centre, IIT Bombay, Mumbai 400 076 (India); Mohanty, T. [Nuclear Science Centre, New Delhi 110 067 (India); Kanjilal, D. [Nuclear Science Centre, New Delhi 110 067 (India)

    2006-03-15

    Gallium antimonide (GaSb) which is a narrow band gap compound semiconductor has received attention because of its potential applications in optoelectronic devices. In the present work, p-type GaSb wafers of <1 0 0> orientation were irradiated with 70 MeV {sup 56}Fe ions at fluences varying from 1 x 10{sup 12} to 1 x 10{sup 14} ions cm{sup -2}. Mid-infrared and Far-infrared Fourier Transform (FT) measurements were carried out to investigate the optical properties of as irradiated and vacuum annealed samples. Mid-infrared Fourier Transform study revealed that the optical absorption of the irradiated samples increases with increasing ion fluence due to increase in irradiation-induced defects. The band gap energy determined from the infrared spectra was found to change from 0.65 to 0.62 eV while for non-irradiated GaSb wafer the corresponding estimate was 0.67 eV. The density of the carrier estimated from the plasma frequency ({omega} {sub p}) was found to vary from 2.05 x 10{sup 18} to 1.9 x 10{sup 18} cm{sup -3}. The samples annealed in vacuum (10{sup -6} mb) over the temperature range 100-600 deg. C showed the significant damage recovery.

  14. Characterization of an azo-calix[4]arene-based optical sensor for Europium (III) ions

    Energy Technology Data Exchange (ETDEWEB)

    Echabaane, M., E-mail: mosaab.echabaane@gmail.com [Laboratoire d' interfaces et Materiaux Avances (LIMA) Faculte des sciences de Monastir, Avenue de l' environnement, 5000 Monastir (Tunisia); Rouis, A. [Laboratoire d' interfaces et Materiaux Avances (LIMA) Faculte des sciences de Monastir, Avenue de l' environnement, 5000 Monastir (Tunisia); Bonnamour, I. [Institut de Chimie and Biochimie Moleculaires and Supramoleculaires (ICBMS), UMR CNRS 5246, 43 Boulevard du 11 Novembre 1918, Universite Claude Bernard Lyon 1, 69100 Villeurbanne (France); Ouada, H. Ben [Laboratoire d' interfaces et Materiaux Avances (LIMA) Faculte des sciences de Monastir, Avenue de l' environnement, 5000 Monastir (Tunisia)

    2012-07-01

    Selective and sensitive optical sensor membranes (optodes) were elaborated to detect cations in aqueous solutions. The sensing films are based on chromogenic calix[4]arene derivatives. The optode membranes were studied using UV/Vis absorption spectroscopy measurements. The sensitivity of the optode has been tested for Pb{sup 2+}, Cd{sup 2+}, Mg{sup 2+} and Eu{sup 3+} ions at pH 6.8. The results showed a good selectivity response towards Eu{sup 3+}. Low selectivity coefficients were observed for Cd{sup 2+} and Mg{sup 2+} where Pb{sup 2+} can be considered as interfering ions. The characteristics of this optode such as response time, regeneration, reproducibility and lifetime are discussed. - Highlights: Black-Right-Pointing-Pointer We report optical sensing studies of chromogenic calixarene derivatives. Black-Right-Pointing-Pointer We investigate optical interaction between azo-calix[4]arene and Eu{sup 3+}. Black-Right-Pointing-Pointer We study sensitivity and selectivity of optode films. Black-Right-Pointing-Pointer We describe characteristics of optode films for determination of europium traces.

  15. One-dimensional ion-beam figuring for grazing-incidence reflective optics.

    Science.gov (United States)

    Zhou, Lin; Idir, Mourad; Bouet, Nathalie; Kaznatcheev, Konstantine; Huang, Lei; Vescovi, Matthew; Dai, Yifan; Li, Shengyi

    2016-01-01

    One-dimensional ion-beam figuring (1D-IBF) can improve grazing-incidence reflective optics, such as Kirkpatrick-Baez mirrors. 1D-IBF requires only one motion degree of freedom, which reduces equipment complexity, resulting in compact and low-cost IBF instrumentation. Furthermore, 1D-IBF is easy to integrate into a single vacuum system with other fabrication processes, such as a thin-film deposition. The NSLS-II Optical Metrology and Fabrication Group has recently integrated the 1D-IBF function into an existing thin-film deposition system by adding an RF ion source to the system. Using a rectangular grid, a 1D removal function needed to perform 1D-IBF has been produced. In this paper, demonstration experiments of the 1D-IBF process are presented on one spherical and two plane samples. The final residual errors on both plane samples are less than 1 nm r.m.s. The surface error on the spherical sample has been successfully reduced by a factor of 12. The results show that the 1D-IBF method is an effective method to process high-precision 1D synchrotron optics.

  16. Optical planar waveguide in sodium-doped calcium barium niobate crystals by carbon ion implantation

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Jin-Hua, E-mail: zhaojinhuazjh@gmail.com [School of Science, Shandong Jianzhu University, Jinan 250101 (China); Qin, Xi-Feng; Wang, Feng-Xiang; Fu, Gang; Wang, Hui-Lin [School of Science, Shandong Jianzhu University, Jinan 250101 (China); Wang, Xue-Lin [School of Physics, Key Laboratory of Particle Physics and Particle Irradiation, Ministry of Education, and State Key Laboratory of Crystal Materials, Shandong University, Jinan 250100 (China)

    2013-07-15

    There is great interest in niobate crystals which belong to the tetragonal tungsten bronze (TTB) families owing to their intriguing properties. As one representative of such crystals, CBN (calcium barium niobate) has attracted rapidly growing attention. Because it has a higher Curie temperature than SBN (strontium barium niobate), possesses outstanding ferroelectric and it possesses optical properties. In addition, doped with sodium, CBN will show a higher Curie temperature than pure CBN. We report on the fabrication and characterization of optical planar waveguide in x-cut sodium-doped calcium barium niobate crystal by using C ion implantation. The guided-mode properties at the wavelength of 633 and 1539 nm are investigated through prism-coupling measurements, respectively. By applying direct end-face coupling arrangement, the near-field optical intensity distribution of waveguide modes is measured at 633 nm. For comparison, the modal profile of the same guided mode is also numerically calculated by the finite difference beam-propagation method via computer software BeamPROP. The transmission spectra of the waveguide before and after ion implantation treatments were investigated also. Our experiment results reveal that the waveguide could propagate light with transverse magnetic polarized direction only and it is assumed that the polarization selectivity of CBN crystal may responsible for this phenomenon.

  17. Optical properties of zinc borotellurite glass doped with trivalent dysprosium ion

    Science.gov (United States)

    Ami Hazlin, M. N.; Halimah, M. K.; Muhammad, F. D.; Faznny, M. F.

    2017-04-01

    The zinc borotellurite doped with dysprosium oxide glass samples with chemical formula {[(TeO2) 0 . 7(B2O3) 0 . 3 ] 0 . 7(ZnO) 0 . 3 } 1 - x(Dy2O3)x (where x=0.01, 0.02, 0.03, 0.04 and 0.05 M fraction) were prepared by using conventional melt quenching technique. The structural and optical properties of the proposed glass systems were characterized by using X-ray diffraction (XRD) spectroscopy, Fourier Transform Infrared (FTIR) spectroscopy, and UV-VIS spectroscopy. The amorphous nature of the glass systems is confirmed by using XRD technique. The infrared spectra of the glass systems indicate three obvious absorption bands which are assigned to BO3 and TeO4 vibrational groups. Based on the absorption spectra obtained, the direct and indirect optical band gaps, as well as the Urbach energy were calculated. It is observed that both the direct and indirect optical band gaps increase with the concentration of Dy3+ ions. On the other hand, the Urbach energy is observed to decrease as the concentration of Dy3+ ions increases.

  18. Optical properties of Eu2+-doped strontium borate glasses containing F- and Li+ ions

    Institute of Scientific and Technical Information of China (English)

    HUANG Yanlin; JANG Kiwan; WANG Xigang; JIANG Chuanfang

    2008-01-01

    In this experiment, strontium borate glasses were prepared using the conventional quenching method in air atmosphere. Optical absorption, photoluminescence excitation and emission spectra, X-ray excited luminescence (XEL), and luminescence decay curve of the as-prepared glasses were investigated at room temperature. The as-prepared glasses had two kinds of Eu ions, i.e., Eu2+ and Eu3+. Compared with the reported results of strontium borate glasses, Eu2+ luminescence was enhanced in the studied strontium borate glasses coprepared with F- and Li+ ions. The coexisting of Li+ or F- in the borate glasses could create more negative defect VSr″ and stabilize Eu2+ ions, which might act as donor of electrons;For the F- doping, the new center of B(O, F)4 (or BO3F) and BO2F2 units could be considered to be the distorted (BO4), which were needed as a rigid framework to stabilize the divalent rare earth ions.

  19. Recent progress in optical coating technology: low-voltage ion plating deposition

    Science.gov (United States)

    Guenther, Karl H.

    1990-08-01

    After fairly extensive discussions of the advantages and disadvantages of low energy and high energy ion beam bombardment of a growing film, we review briefly a number of experimental results obtained with various samples made with low voltage reactive ion plating deposition. The availability of a state-of-the-art high vacuum coating machine specifically equipped for this process is the foundation for a major leap toward achieving near-perfect optical coatings. The high density of ion plated thin films makes them impermeable to water vapor and corrosive solutions. This has been demonstrated with protected aluminum mirrors, polarizers, and infrared anti-reflection coatings. An indication of the high packing density is the substantially higher refractive index than that of comparable layers deposited with either conventional electron beam evaporation or ion assisted deposition. The spectral transmittance of multilayer stacks of oxide thin films is lower than expected from theoretical predictions which assume absorption-free dielectrics. The observed absorption is primarily of an interface nature rather than a volume effect and occurs predominantly in combinations of Ti02 and Si02 thin films.

  20. Effect of F ions on physical and optical properties of fluorine substituted zinc arsenic tellurite glasses

    Science.gov (United States)

    Kareem Ahmmad, Shaik; kondaul, Edu; Rahman, Syed

    2015-02-01

    The effect of substitution of fluoride ions for oxide ions on the physical and optical properties of glass system (20-x) ZnO-xZnF2-40As2O3-40TeO2 where x = 0, 4, 8,12,16,20 mole % were investigated. The samples prepared by melt quenching method under controlled condition. The amorphous nature of these glasses was checked by X-ray diffraction technique. The density was measured according to Archimedes principle. The room temperature absorption spectra of all glass samples were determined using UV-Vis-NIR spectrometer. The thermal behaviour, glass transition temperature and stability of glass samples were studied by a differential scanning calorimetric (DSC). The density reduction of present glasses with ZnF2 concentrations may be due to the low density of ZnF2 compared with that of ZnO. Breaking the oxide network, the cross linking degree of the glass former could be reduced which results in decrease of both Tg and Tx. In the present glass system when F ions replaced by oxygen ions UV-Vis absorption cut-off wavelength decreases. This resulted form the conversion of structural unit in the glass from TeO4 to Te(O,F)4 and then to Te(O, F)3.

  1. Fabrication of optical waveguides in KGW by swift heavy ion beam irradiation

    Science.gov (United States)

    García-Navarro, A.; Olivares, J.; García, G.; Agulló-López, F.; García-Blanco, S.; Merchant, C.; Aitchison, J. Stewart

    2006-08-01

    Irradiations with F, O at 25 MeV and C at 14 MeV energy have been performed in KGd(WO4)2 (KGW) in order to fabricate optical waveguides by a novel route based on ion irradiation instead of ion implantation. The method relies on selecting the energy high enough so as to place the maximum of the electronic stopping power a few microns inside the crystal. Then, buried isotropic layers (amorphous-like) are formed which have a low refractive index value of 1.87 (compared to the three crystalline values which are above 2.0). The refractive index profiles obtained are Gaussian-like with O ions and more step-like with the usage of C ions. Fairly low fluences in the range 1 × 1013-1 × 1014 have been successfully explored. The results have been compared to those recently obtained for LiNbO3 and have been analyzed with a theoretical model based on thermal spike concept.

  2. Fabrication and comprehensive modeling of ion-exchanged Bragg optical add-drop multiplexers.

    Science.gov (United States)

    Castro, Jose M; Geraghty, David F; West, Brian R; Honkanen, Seppo

    2004-11-20

    Optical add-drop multiplexers (OADMs) based on asymmetric Y branches and tilted gratings offer excellent-performance in wavelength-division multiplexed systems. To simplify waveguide fabrication, ion-exchange techniques appear to be an important option in photosensitive glasses. Optimum OADM performance depends on how accurately the waveguide fabrication process and tilted Bragg grating operation are understood and modeled. Results from fabrication and comprehensive modeling are compared for ion-exchange processes that use different angles of the tilted grating. The transmission and reflection spectra for the fabricated and simulated OADMs show excellent agreement. The OADM's performance is evaluated in terms of the measured characteristics of the Y branches and tilted gratings.

  3. Optical probing of Eu ions confined in an RF trap

    Indian Academy of Sciences (India)

    Pushpa M Rao; Anita Gupta

    2012-01-01

    The Eu ions confined in an RF quadrupole trap, has been optically detected. Using a tunable dye laser which is pumped by a Nd-YAG pulsed laser system, the resonance ${}^9S_4–6 p_{3/2}$, = 5 transition of the Eu ions have been excited and the resulting fluorescence to the metastable ${}^9 D_{4−6}$ state has been detected. In preparation to determine the ground-state hyperfine splitting of the odd isotopes we found the optimum trapping operating point. We have also observed a number of instabilities inside the region of the stability for an ideal trap. These non-linear resonances arise from higher-order contributions to the ideal quadrupole potential.

  4. Layer compression and enhanced optical properties of few-layer graphene nanosheets induced by ion irradiation

    CERN Document Server

    Tan, Yang; Akhmadaliev, Shavkat; Zhou, Shengqiang; Chen, Feng

    2016-01-01

    Graphene has been recognized as an attractive two-dimensional material for fundamental research and wide applications in electronic and photonic devices owing to its unique properties. The technologies to modulate the properties of graphene are of continuous interest to researchers in multidisciplinary areas. Herein, we report on the first experimental observation of the layer-to-layer compression and enhanced optical properties of few-layer graphene nanosheets by applying the irradiation of energetic ion beams. After the irradiation, the space between the graphene layers was reduced, resulting in a tighter contact between the few-layer graphene nanosheet and the surface of the substrate. This processing also enhanced the interaction between the graphene nanosheets and the evanescent-field wave near the surface, thus reinforcing the polarization-dependent light absorption of the graphene layers (with 3-fold polarization extinction ratio increment). Utilizing the ion-irradiated graphene nanosheets as saturable...

  5. Multi-Rare-Earth Ions Codoped Tellurite Glasses for Potential Dual Wavelength Fibre-Optic Amplifiers

    Institute of Scientific and Technical Information of China (English)

    DAI Shi-Xun; YANG Jian-Hu; XU Shi-Qing; DAI Neng-Li; WEN Lei; HU Li-Li; JIANG Zhong-Hong

    2003-01-01

    A novel co-doping method of multi-rare-earth (RE) ions was demonstrated in tellurite glasses for fibre amplifiers. Fluorescence emissions at both 1.53 and 1.63 fj,m communication windows were Brstly observed from Er3+ /Yb3+ /Tm3+ -codoped tellurite glasses under a single wavelength pumping at 980 nm. The full width at half maximum of Suorescence at 1.53 and 1.63 [im are 55 nm and 50 urn, respectively. Tm's codoping method of three RE ions could be applied to other low photon energy glasses, which would be possibly used for potential dual wavelength fibre-optic amplifiers to broaden the communication windows.

  6. Ion-Optics Calculations and Preliminary Precision Estimates of the Gas-Capable Ion Source for the 1-MV LLNL BioAMS Spectrometer

    Energy Technology Data Exchange (ETDEWEB)

    Ognibene, T J; Bench, G; Brown, T A; Vogel, J S

    2005-12-13

    Ion-optics calculations were performed for a new ion source and injection beam line. This source, which can accept both solid and gaseous targets, will be installed onto the 1-MV BioAMS spectrometer at the Center for Accelerator Mass Spectrometry, located at Lawrence Livermore National Laboratory and will augment the current LLNL cesium-sputter solid sample ion source. The ion source and its associated injection beam line were designed to allow direct quantification of {sup 14}C/{sup 12}C and {sup 3}H/{sup 1}H isotope ratios from both solid and gaseous targets without the need for isotope switching. Once installed, this source will enable the direct linking of a nanoflow LC system to the spectrometer to provide for high-throughput LC-AMS quantitation from a continuous flow. Calculations show that, for small samples, the sensitivity of the gas-accepting ion source could be precision limited but zeptomole quantitation should be feasible.

  7. Optics of the NIFS negative ion source test stand by infrared calorimetry and numerical modelling.

    Science.gov (United States)

    Veltri, P; Antoni, V; Agostinetti, P; Brombin, M; Ikeda, K; Kisaki, M; Nakano, H; Sartori, E; Serianni, G; Takeiri, Y; Tsumori, K

    2016-02-01

    At National Institute for Fusion Science (NIFS), a multi-ampere negative ion source is used to support the R&D on H(-) production, extraction, and acceleration. In this contribution, we study the characteristics of the acceleration system of this source, in order to characterize the beam optics at different operational conditions. A dedicated experimental campaign was carried out at NIFS, using as main diagnostic the infra-red imaging of the beam profiles. The experimental measurements are also compared with 3D numerical simulations, in order to validate the codes and to assess their degree of reliability. The simulations show a satisfactory agreement with the experimental results.

  8. Optics of the NIFS negative ion source test stand by infrared calorimetry and numerical modelling

    Energy Technology Data Exchange (ETDEWEB)

    Veltri, P., E-mail: pierluigi.veltri@igi.cnr.it; Antoni, V.; Agostinetti, P.; Brombin, M.; Sartori, E.; Serianni, G. [Consorzio RFX (CNR, ENEA, INFN, Università di Padova, Acciaierie Venete SpA), Corso Stati Uniti 4, 35127 Padova (Italy); Ikeda, K.; Kisaki, M.; Nakano, H.; Takeiri, Y.; Tsumori, K. [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan)

    2016-02-15

    At National Institute for Fusion Science (NIFS), a multi-ampere negative ion source is used to support the R&D on H{sup −} production, extraction, and acceleration. In this contribution, we study the characteristics of the acceleration system of this source, in order to characterize the beam optics at different operational conditions. A dedicated experimental campaign was carried out at NIFS, using as main diagnostic the infra-red imaging of the beam profiles. The experimental measurements are also compared with 3D numerical simulations, in order to validate the codes and to assess their degree of reliability. The simulations show a satisfactory agreement with the experimental results.

  9. Optics of the NIFS negative ion source test stand by infrared calorimetry and numerical modelling

    Science.gov (United States)

    Veltri, P.; Antoni, V.; Agostinetti, P.; Brombin, M.; Ikeda, K.; Kisaki, M.; Nakano, H.; Sartori, E.; Serianni, G.; Takeiri, Y.; Tsumori, K.

    2016-02-01

    At National Institute for Fusion Science (NIFS), a multi-ampere negative ion source is used to support the R&D on H- production, extraction, and acceleration. In this contribution, we study the characteristics of the acceleration system of this source, in order to characterize the beam optics at different operational conditions. A dedicated experimental campaign was carried out at NIFS, using as main diagnostic the infra-red imaging of the beam profiles. The experimental measurements are also compared with 3D numerical simulations, in order to validate the codes and to assess their degree of reliability. The simulations show a satisfactory agreement with the experimental results.

  10. Optical planar waveguides in Yb3+-doped phosphate glasses produced by He+ ion implantation

    Institute of Scientific and Technical Information of China (English)

    Liu Chun-Xiao; Li Wei-Nan; Wei Wei; Peng Bo

    2012-01-01

    Optical planar waveguides in Yb3+-doped phosphate glasses are fabricated by implanting triple-energy helium ions.The guiding modes and the near-field intensity distribution are measured by using the prism-coupling method and the end-face coupling setup with a He-Ne laser at 633 nm The intensity calculation method (ICM) is used to reconstruct the refractive index profile of the waveguide.The absorption and the fluorescence investigations reveal that the glass bulk features are well preserved in the active volumes of the waveguides,suggesting the fabricated structures for possible applications as waveguide lasers.

  11. Realization of collective strong coupling with ion Coulomb crystals in an optical cavity

    DEFF Research Database (Denmark)

    Herskind, Peter Fønss; Dantan, Aurélien; Marler, Joan

    2009-01-01

    crystal 16 and an optical field. The obtained coherence times are in the millisecond range and indicate that Coulomb crystals positioned inside optical cavities are promising for realizing a variety of quantum-information devices, including quantum repeaters 12 and quantum memories for light 17, 18......Cavity quantum electrodynamics (CQED) focuses on understanding the interactions between matter and the electromagnetic field in cavities at the quantum level 1, 2 . In the past years, CQED has attracted attention 3, 4, 5, 6, 7, 8, 9 especially owing to its importance for the field of quantum...... information 10 . At present, photons are the best carriers of quantum information between physically separated sites 11, 12 and quantum-information processing using stationary qubits 10 is most promising, with the furthest advances having been made with trapped ions 13, 14, 15 . The implementation of complex...

  12. Analysis of an aggregation-based algebraic two-grid method for a rotated anisotropic diffusion problem

    KAUST Repository

    Chen, Meng-Huo

    2015-03-18

    Summary: A two-grid convergence analysis based on the paper [Algebraic analysis of aggregation-based multigrid, by A. Napov and Y. Notay, Numer. Lin. Alg. Appl. 18 (2011), pp. 539-564] is derived for various aggregation schemes applied to a finite element discretization of a rotated anisotropic diffusion equation. As expected, it is shown that the best aggregation scheme is one in which aggregates are aligned with the anisotropy. In practice, however, this is not what automatic aggregation procedures do. We suggest approaches for determining appropriate aggregates based on eigenvectors associated with small eigenvalues of a block splitting matrix or based on minimizing a quantity related to the spectral radius of the iteration matrix. © 2015 John Wiley & Sons, Ltd.

  13. Optics measurement and correction during beam acceleration in the Relativistic Heavy Ion Collider

    Energy Technology Data Exchange (ETDEWEB)

    Liu, C. [Brookhaven National Lab. (BNL), Upton, NY (United States). Collider-Accelerator Dept.; Marusic, A. [Brookhaven National Lab. (BNL), Upton, NY (United States). Collider-Accelerator Dept.; Minty, M. [Brookhaven National Lab. (BNL), Upton, NY (United States). Collider-Accelerator Dept.

    2014-09-09

    To minimize operational complexities, setup of collisions in high energy circular colliders typically involves acceleration with near constant β-functions followed by application of strong focusing quadrupoles at the interaction points (IPs) for the final beta-squeeze. At the Relativistic Heavy Ion Collider (RHIC) beam acceleration and optics squeeze are performed simultaneously. In the past, beam optics correction at RHIC has taken place at injection and at final energy with some interpolation of corrections into the acceleration cycle. Recent measurements of the beam optics during acceleration and squeeze have evidenced significant beta-beats which if corrected could minimize undesirable emittance dilutions and maximize the spin polarization of polarized proton beams by avoidance of higher-order multipole fields sampled by particles within the bunch. In this report the methodology now operational at RHIC for beam optics corrections during acceleration with simultaneous beta-squeeze will be presented together with measurements which conclusively demonstrate the superior beam control. As a valuable by-product, the corrections have minimized the beta-beat at the profile monitors so reducing the dominant error in and providing more precise measurements of the evolution of the beam emittances during acceleration.

  14. Investigation of Optical and Luminescence Properties of Soda Lime Borate Glasses Doped with Sm3+ Ion

    Institute of Scientific and Technical Information of China (English)

    FALAK; Zaman; GUL; Rooh; NATTAPON; Srisittipokakun; JACKRAPONG; Kaewkhao

    2016-01-01

    This paper was to investigate the optical and luminescence properties of Sm3+ doped SLB glasses by a melt quenching technique. The optical and luminescence properties of the prepared glass samples were investigated via absorption and photoluminescence spectra, respectively. The related physical and optical parameters were also calculated. From optical absorption measurements, the transition 6H5/2 → 6P3/2 at 403 nm has a higher spectral intensity and is a hypersensitive transition. From photoluminescence spectra, four prominent emission spectra appear. The most intense band is located at 4G5/2 →6H9/2(599 nm), which is the characteristic emission range of Sm3+ ions with the reddish orange color. The experimental decay time of the 4G5/2 level of Sm3+ SLB glasses was determined. The decay time decreases from 1.367 to 0.333 ms with increasing the content of Sm3+. The color coordinates(x, y) of the prepared glasses passes through the reddish-orange region in the CIE 1931 diagram and are suitable for orange LEDs, optoelectronics, and solidstate lighting. The further investigation on the optimization of the dopant content in the SLB glasses was suggested.

  15. Influence irradiation argon ion SnO2 on optical and electrical characteristics

    Science.gov (United States)

    Asainov, O.; Umnov, S.; Temenkov, V.

    2017-01-01

    Tin oxide in the form of films has been deposited by reactive magnetron sputtering on glass substrates a room temperature. Process was carried out in such mode when the deposited films were conductive. The deposited films were irradiated with argon ions. Have been studied happening at that the changes optical and electric properties of films. Have been investigated optical properties of films in the range of 300-1100 nanometers by means of photometry. For research structure of films was used the x-ray diffractometry. Diffractometric researches have shown that the films deposited on a substrate have crystal structure from shares of a quasicrystal phase and after influence of argon ions she completely became quasicrystal. It is established that change transmission of a film correlates with change her electric resistance. Average value transmission in the range of 380-1100 nanometers as well as the electric resistance of a film with growth of irradiation time increases to the values exceeding initial. At the same time at irradiation time ∼ 13,2 sec. are observed their slight decrease. To this value of irradiation time there corresponds the minimum value of electric resistance and transmission films. Change of transmission coefficient correlates with change of surface resistance.

  16. Ag7+ ion induced modification of morphology, optical and luminescence behaviour of charge compensated CaMoO4 nanophosphor

    Science.gov (United States)

    Dutta, S.; Som, S.; Kunti, A. K.; Sharma, S. K.; Kumar, Vijay; Swart, H. C.; Visser, H. G.

    2016-10-01

    The present paper reports on the swift heavy ion (SHI) induced structural, optical and luminescence properties of CaMoO4:Dy3+/K+ nanophosphor synthesized via hydrothermal route. Herein 100 MeV Ag7+ ion beam was used varying fluence from 1 × 1011 to 1 × 1013 ions/cm2. The depth profile of the Ag7+ ions was estimated using SRIM code. XRD and FESEM results revealed the loss of crystallinity and reduction in particle size after SHI irradiations. The XPS technique confirmed the stability of oxidation states of the elements. Reflectance spectra exhibited a red shift in the absorption band, followed by a decrease in band gap. Decrease in the intensity of the photoluminescence peaks without any change in band positions was also obtained after ion irradiation. The thermoluminescence (TL) characteristics were discussed in detail, and the trapping parameter was calculated. The results were compared on the grounds of linear energy transfer of the irradiated ions.

  17. Optical properties of AlGaN nanowires synthesized via ion beam techniques

    Science.gov (United States)

    Parida, Santanu; Magudapathy, P.; Sivadasan, A. K.; Pandian, Ramanathaswamy; Dhara, Sandip

    2017-05-01

    AlGaN plays a vital role in hetero-structure high electron mobility transistors by employing a two-dimensional electron gas as an electron blocking layer in multi-quantum well light emitting diodes. Nevertheless, the incorporation of Al into GaN for the formation of the AlGaN alloy is limited by the diffusion barrier formed by instant nitridation of Al adatoms by reactive atomic N. The incorporation of Al above the miscibility limit, however, can be achieved by the ion beam technique. The well known ion beam mixing (IBM) technique was carried out with the help of Ar+ irradiation for different fluences. A novel approach was also adopted for the synthesis of AlGaN by the process of post-irradiation diffusion (PID) as a comparative study with the IBM technique. The optical investigations of AlGaN nanowires, synthesized via two different methods of ion beam processing, are reported. The effect of irradiation fluence and post-irradiation annealing temperature on the random alloy formation was studied by the vibrational and photoluminescence (PL) spectroscopic studies. Vibrational studies show one-mode phonon behavior corresponding to the longitudinal optical (LO) mode of A1 symmetry [A1(LO)] for the wurtzite phase of AlGaN nanowires in the random alloy model. A maximum Al atomic percentage of ˜6.3%-6.7% was calculated with the help of band bowing formalism from the Raman spectral analysis for samples synthesized in IBM and PID processes. PL studies show the extent of defects present in these samples.

  18. Investigation of optical and spectroscopic properties of Sm3+ ions in CaBAl glasses

    Science.gov (United States)

    Brito, D. R. N.; Queiroz, M. N.; Barboza, M. J.; Steimacher, A.; Pedrochi, F.

    2017-02-01

    Samples of CaBAl glass with composition of (25-x)CaO-50B2O3-15Al2O3-10CaF2-xSm2O3, with Sm2O3 concentration varying from 0.5 to 7 wt%, were prepared by using melt-quenching method in air atmosphere. The samples were prepared with different concentrations of Sm2O3, aiming to understand how the dopant changes the optical and spectroscopic properties of the glass. The doped CaBAl glasses were studied by means of volumetric density measurements, refractive index, optical absorption, luminescence at room temperature, luminescence as function of the temperature and radiative lifetime. All results were discussed in function of Sm2O3 concentration. The measured volumetric density and polarizability showed an increase with Sm2O3 doping. The refractive index showed a small increase due to RE doping, although within the errors. The absorption bands were attributed to Sm3+ transitions from the ground state 6H5/2 to the various excited states. The luminescence spectra present emission bands assigned to the appropriate electronic f-f transitions of Sm3+ ions; there are four emission bands at 565, 602, 649 and 710 nm. The luminescence quenching was observed up to 2 wt% of Sm2O3. The O/R ratio as function of the Sm2O3 concentration showed changes in the symmetry site with addition of Sm2O3. The CIE 1931 diagram presented a reddish-orange shift color with Sm2O3 doping. The luminescence intensity presents a decrease with temperature increase for all studied samples. The experimental lifetime decreases with the increase of Sm2O3, mainly due to ion-ion interaction.

  19. Compositional, structural, and optical changes of polyimide implanted by 1.0 MeV Ni+ ions

    Science.gov (United States)

    Mikšová, R.; Macková, A.; Pupikova, H.; Malinský, P.; Slepička, P.; Švorčík, V.

    2017-09-01

    The ion irradiation leads to deep structural and compositional changes in the irradiated polymers. Ni+ ions implanted polymers were investigated from the structural and compositional changes point of view and their optical properties were investigated. Polyimide (PI) foils were implanted with 1.0 MeV Ni+ ions at room temperature with fluencies of 1.0 × 1013-1.0 × 1015 cm-2 and two different ion implantation currents densities (3.5 and 7.2 nA/cm2). Rutherford Back-Scattering (RBS) and Elastic Recoil Detection Analysis (ERDA) were used for determination of oxygen and hydrogen escape in implanted PI. Atomic Force Microscopy (AFM) was used to follow surface roughness modification after the ion implantation and UV-Vis spectroscopy was employed to check the optical properties of the implanted PI. The implanted PI structural changes were analysed using Attenuated Total Reflection Fourier Transform Infrared Spectroscopy (ATR-FTIR). High energy Ni-ion implantation causes only a minor release of hydrogen and oxygen close to the polymer sub-surface region in about 60 nm thick layer penetrated by the ion beam; especially at ion fluencies below 1.0 × 1014 cm-2. The mostly pronounced structural changes of the Ni implanted PI were found for the samples implanted above ion fluence 1.0 × 1015 cm-2 and at the ion current density 7.2 nA/cm2, where the optical band gap significantly decreases and the reduction of more complex structural unit of PI monomer was observed.

  20. Evaluation of copper ion of antibacterial effect on Pseudomonas aeruginosa, Salmonella typhimurium and Helicobacter pylori and optical, mechanical properties

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Young-Hwan [School of Materials Science and Engineering, University of Yonsei, Seoul (Korea, Republic of); Choi, Yu-ri; Kim, Kwang-Mahn [Department and Research Institute of Dental Biomaterials and Bioengineering, College of Dentistry, University of Yonsei, Seoul (Korea, Republic of); Choi, Se-Young, E-mail: sychoi@yonsei.ac.kr [School of Materials Science and Engineering, University of Yonsei, Seoul (Korea, Republic of)

    2012-02-01

    Antibacterial effect on Pseudomonas aeruginosa, Salmonella typhimurium and Helicobacter pylori of copper ion was researched. Also, additional effects of copper ion coating on optical and mechanical properties were researched as well. Copper ion was coated on glass substrate as a thin film to prevent bacteria from growing. Cupric nitrate was used as precursors for copper ion. The copper ion contained sol was deposited by spin coating process on glass substrate. Then, the deposited substrates were heat treated at the temperature range between 200 Degree-Sign C and 250 Degree-Sign C. The thickness of deposited copper layer on the surface was 63 nm. The antibacterial effect of copper ion coated glass on P. aeruginosa, S. typhimurium and H. pylori demonstrated excellent effect compared with parent glass. Copper ion contained layer on glass showed a similar value of transmittance compared with value of parent glass. The 3-point bending strength and Vickers hardness were 209.2 MPa, 540.9 kg/mm{sup 2} which were about 1.5% and 1.3% higher than the value of parent glass. From these findings, it is clear that copper ion coating on glass substrate showed outstanding effect not only in antibacterial activity but also in optical and mechanical properties as well.

  1. Evaluation of copper ion of antibacterial effect on Pseudomonas aeruginosa, Salmonella typhimurium and Helicobacter pylori and optical, mechanical properties

    Science.gov (United States)

    Kim, Young-Hwan; Choi, Yu-ri; Kim, Kwang-Mahn; Choi, Se-Young

    2012-02-01

    Antibacterial effect on Pseudomonas aeruginosa, Salmonella typhimurium and Helicobacter pylori of copper ion was researched. Also, additional effects of copper ion coating on optical and mechanical properties were researched as well. Copper ion was coated on glass substrate as a thin film to prevent bacteria from growing. Cupric nitrate was used as precursors for copper ion. The copper ion contained sol was deposited by spin coating process on glass substrate. Then, the deposited substrates were heat treated at the temperature range between 200 °C and 250 °C. The thickness of deposited copper layer on the surface was 63 nm. The antibacterial effect of copper ion coated glass on P. aeruginosa, S. typhimurium and H. pylori demonstrated excellent effect compared with parent glass. Copper ion contained layer on glass showed a similar value of transmittance compared with value of parent glass. The 3-point bending strength and Vickers hardness were 209.2 MPa, 540.9 kg/mm2 which were about 1.5% and 1.3% higher than the value of parent glass. From these findings, it is clear that copper ion coating on glass substrate showed outstanding effect not only in antibacterial activity but also in optical and mechanical properties as well.

  2. Deep Reactive Ion Etched Anti-Reflection Coatings for Sub-millimeter Silicon Optics

    CERN Document Server

    Gallardo, Patricio A; Cothard, Nicholas; Bruno, Sarah Marie M; Cortes-Medellin, German; Marchetti, Galen; Miller, Kevin H; Mockler, Brenna; Niemack, Michael D; Stacey, Gordon; Wollack, Edward J

    2016-01-01

    Refractive optical elements are widely used in millimeter and sub-millimeter astronomical telescopes. High resistivity silicon is an excellent material for dielectric lenses given its low loss-tangent, high thermal conductivity and high index of refraction. The high index of refraction of silicon causes a large Fresnel reflectance at the vacuum-silicon interface (up to 30%), which can be reduced with an anti-reflection (AR) coating. In this work we report techniques for efficiently AR coating silicon at sub-millimeter wavelengths using Deep Reactive Ion Etching (DRIE) and bonding the coated silicon to another silicon optic. Silicon wafers of 100 mm diameter (1 mm thick) were coated and bonded using the Silicon Direct Bonding technique at high temperature (1100 C). No glue is used in this process. Optical tests using a Fourier Transform Spectrometer (FTS) show sub-percent reflections for a single-layer DRIE AR coating designed for use at 320 microns on a single wafer. Cryogenic (10 K) measurements of a bonded ...

  3. Deep reactive ion etched anti-reflection coatings for sub-millimeter silicon optics.

    Science.gov (United States)

    Gallardo, Patricio A; Koopman, Brian J; Cothard, Nicholas F; Bruno, Sarah Marie M; Cortes-Medellin, German; Marchetti, Galen; Miller, Kevin H; Mockler, Brenna; Niemack, Michael D; Stacey, Gordon; Wollack, Edward J

    2017-04-01

    Refractive optical elements are widely used in millimeter and sub-millimeter (sub-mm) astronomical telescopes. High-resistivity silicon is an excellent material for dielectric lenses given its low loss tangent, high thermal conductivity, and high index of refraction. The high index of refraction of silicon causes a large Fresnel reflectance at the vacuum-silicon interface (up to 30%), which can be reduced with an anti-reflection (AR) coating. In this work, we report techniques for efficiently AR coating silicon at sub-mm wavelengths using deep reactive ion etching (DRIE) and bonding the coated silicon to another silicon optic. Silicon wafers of 100 mm diameter (1 mm thick) were coated and bonded using the silicon direct bonding technique at high temperature (1100°C). No glue is used in this process. Optical tests using a Fourier transform spectrometer show sub-percent reflections for a single-layer DRIE AR coating designed for use at 320 μm on a single wafer. Cryogenic (10 K) measurements of a bonded pair of AR-coated wafers also reached sub-percent reflections. A prototype two-layer DRIE AR coating to reduce reflections and increase bandwidth is presented, and plans for extending this approach are discussed.

  4. Optical Properties of Ar Ions Irradiated Nanocrystalline ZrC and ZrN Thin Films

    Science.gov (United States)

    Martin, C.; Miller, K. H.; Makino, H.; Craciun, D.; Simeone, D.; Craciun, V.

    2016-01-01

    Thin nanocrystalline ZrC and ZrN films (less than 400 nanometers), grown on (100) Si substrates at a substrate temperature of 500 degrees Centigrade by the pulsed laser deposition (PLD) technique, were irradiated by 800 kiloelectronvolts Ar ion irradiation with fluences from 1 times 10(sup 14) atoms per square centimeter up to 2 times 10(sup 15) atoms per square centimeter. Optical reflectance data, acquired from as-deposited and irradiated films, in the range of 500-50000 per centimeter (0.06–6 electronvolts), was used to assess the effect of irradiation on the optical and electronic properties. Both in ZrC and ZrN films we observed that irradiation affects the optical properties of the films mostly at low frequencies, which is dominated by the free carriers response. In both materials, we found a significant reduction in the free carriers scattering rate, i.e. possible increase in mobility, at higher irradiation flux. This is consistent with our previous findings that irradiation affects the crystallite size and the micro-strain, but it does not induce major structural changes.

  5. Frequency comparison of ${}^{171}$Yb${}^+$ ion optical clocks at PTB and NPL via GPS PPP

    CERN Document Server

    Leute, J; Lipphardt, B; Tamm, Chr; Nisbet-Jones, P B R; King, S A; Godun, R M; Jones, J M; Margolis, H S; Whibberley, P B; Wallin, A; Merimaa, M; Gill, P; Peik, E

    2015-01-01

    We used Precise Point Positioning, a well-established GPS carrier-phase frequency transfer method to perform a direct remote comparison of two optical frequency standards based on single laser-cooled $^{171}$Yb$^+$ ions operated at NPL, UK and PTB, Germany. At both institutes an active hydrogen maser serves as a flywheel oscillator; it is connected to a GPS receiver as an external frequency reference and compared simultaneously to a realization of the unperturbed frequency of the ${{}^2S_{1/2}(F=0)-{}^2D_{3/2}(F=2)}$ electric quadrupole transition in ${}^{171}$Yb${}^+$ via an optical femtosecond frequency comb. To profit from long coherent GPS link measurements we extrapolate over the various data gaps in the optical clock to maser comparisons which introduces maser noise to the frequency comparison but improves the uncertainty from the GPS link. We determined the total statistical uncertainty consisting of the GPS link uncertainty and the extrapolation uncertainties for several extrapolation schemes. Using t...

  6. Optical Properties of dual ion beam sputtered Indium Tin Oxide films on glass and Silicon

    Science.gov (United States)

    Simpson, Nelson; Geerts, Wilhelmus; Bandyopadhyay, Anup

    2012-03-01

    Indium Tin Oxide (ITO) is a transparent conducting material that finds application in flat panel displays, solar cells, and photodetectors. High quality ITO films, i.e. films with a large transparency and a high conductivity, are normally deposited above room temperature often at 300-400 C. This high deposition temperature eliminates most plastics as substrates. To lower the substrate deposition temperature we are applying atomic instead of molecular oxygen during the sputtering process. A dual ion beam sputtering system (DIBS) has been modified to allow the substrate to be exposed to an atomic oxygen beam at 45 degrees angle of incidence. Thin films were sputtered as a function of atomic oxygen flux and substrate temperature on glass, silicon, and sapphire substrates. The optical properties were measured by spectroscopic ellipsometry, reflectometry, and FTIR. Film thickness and bandgap were determined from the optical properties in the visible part of the spectrum. Mobility was determined from the infrared part of the spectruam. Optical properties appear to vary with the film thickness, the oxygen flux, and the substrate temperature. Roughness of the samples was independently measured by AFM. This work is supported by a grant from research corporation (10775).

  7. Fabrication of optical channel waveguides in crystals and glasses using macro- and micro ion beams

    Energy Technology Data Exchange (ETDEWEB)

    Bányász, I., E-mail: banyasz@sunserv.kfki.hu [Wigner Research Centre for Physics, Hungarian Academy of Sciences, P.O. Box 49, H-1525 Budapest (Hungary); Rajta, I.; Nagy, G.U.L. [MTA Atomki, Institute for Nuclear Research, Hungarian Academy of Sciences, P.O. Box 51, H-4001 Debrecen (Hungary); Zolnai, Z. [Research Institute for Technical Physics and Materials Science, Research Centre for Natural Sciences, Hungarian Academy of Sciences, P.O. Box 49, H-1525 Budapest (Hungary); Havranek, V. [Nuclear Physics Institute AV CR, Řež near Prague 250 68 (Czech Republic); Pelli, S. [MDF-Lab, “Nello Carrara” Institute of Applied Physics, IFAC-CNR, Via Madonna del Piano 10, 50019 Sesto Fiorentino, FI (Italy); “Enrico Fermi” Center for Study and Research, Piazza del Viminale 2, 00184 Roma (Italy); Veres, M. [Wigner Research Centre for Physics, Hungarian Academy of Sciences, P.O. Box 49, H-1525 Budapest (Hungary); Berneschi, S.; Nunzi-Conti, G. [MDF-Lab, “Nello Carrara” Institute of Applied Physics, IFAC-CNR, Via Madonna del Piano 10, 50019 Sesto Fiorentino, FI (Italy); Righini, G.C. [“Enrico Fermi” Center for Study and Research, Piazza del Viminale 2, 00184 Roma (Italy)

    2014-07-15

    Active and passive optical waveguides are fundamental elements in modern telecommunications systems. A great number of optical crystals and glasses were identified and are used as good optoelectronic materials. However, fabrication of waveguides in some of those materials remains still a challenging task due to their susceptibility to mechanical or chemical damages during processing. Researches were initiated on ion beam fabrication of optical waveguides in tellurite glasses. Channel waveguides were written in Er:TeO{sub 2}–WO{sub 3} glass through a special silicon mask using 1.5 MeV N{sup +} irradiation. This method was improved by increasing N{sup +} energy to 3.5 MeV to achieve confinement at the 1550 nm wavelength, too. An alternative method, direct writing of the channel waveguides in the tellurite glass using focussed beams of 6–11 MeV C{sup 3+} and C{sup 5+} and 5 MeV N{sup 3+}, has also been developed. Channel waveguides were fabricated in undoped eulytine-(Bi{sub 4}Ge{sub 3}O{sub 12}) and sillenite type (Bi{sub 12}GeO{sub 20}) bismuth germanate crystals using both a special silicon mask and a thick SU8 photoresist mask and 3.5 MeV N{sup +} irradiation. The waveguides were studied by phase contrast and interference microscopy and micro Raman spectroscopy. Guiding properties were checked by the end fire method.

  8. Integrated optic chemical sensor for the simultaneous detection and quantification of multiple ions. Final report, March--September 1995

    Energy Technology Data Exchange (ETDEWEB)

    Mendoza, E.

    1995-09-01

    This final report summarizes the work performed by Physical Optics Corporation (POC) on the DOE contract entitled {open_quotes}Integrated Optic Chemical Sensor for the Simultaneous Detection and Quantification of Multiple Metal Ions{close_quotes}. This project successfully demonstrated a multi-element integrated optic chemical sensor (IOCS) system capable of simultaneous detection and quantification of metal ions in a water flow stream. POC`s innovative integrated optic chemical sensor technology uses an array of chemically active optical waveguides integrated in parallel in a single small IOCS chip. The IOCS technique uses commonly available materials and straightforward processing to produce channel waveguides in porous glass, each channel treated with a chemical indicator that responds optically to heavy metal ions in a water flow stream. The porosity of the glass allows metal ions present in the water to diffuse into the glass and interact with the immobilized indicators, producing a measurable optical chance. For the {open_quotes}proof-of-concept{close_quotes} demonstration, POC designed and fabricated two types of IOCS chips. Type I uses an array of four straight channel waveguides, three of which are doped with a metal sensitive indicator, an ionophore. The undoped fourth channel is used as the reference channel. Type II uses a 1 x 4 star coupler structure with three sensing channels and a reference channel. Successful implementation of the IOCS technology is expected to have a broad impact on water quality control as well as in the commercial environmental monitoring market. Because of the self-referenced, multidetection capability of the IOCS technique, POC`s water quality sensors are expected to find markets in environmental monitoring and protection, ground water monitoring, and in-line process control. Specific applications include monitoring of chromium, copper, and iron ions in water discharged by the metal plating industry.

  9. Optical transitions in highly charged californium ions with high sensitivity to variation of the fine-structure constant.

    Science.gov (United States)

    Berengut, J C; Dzuba, V A; Flambaum, V V; Ong, A

    2012-08-17

    We study electronic transitions in highly charged Cf ions that are within the frequency range of optical lasers and have very high sensitivity to potential variations in the fine-structure constant, α. The transitions are in the optical range despite the large ionization energies because they lie on the level crossing of the 5f and 6p valence orbitals in the thallium isoelectronic sequence. Cf(16+) is a particularly rich ion, having several narrow lines with properties that minimize certain systematic effects. Cf(16+) has very large nuclear charge and large ionization energy, resulting in the largest α sensitivity seen in atomic systems. The lines include positive and negative shifters.

  10. Au{sup 3+} ion implantation on FTO coated glasses: Effect on structural, electrical, optical and phonon properties

    Energy Technology Data Exchange (ETDEWEB)

    Sahu, Bindu; Dey, Ranajit; Bajpai, P.K., E-mail: bajpai.pk1@gmail.com

    2017-06-01

    Highlights: • Effects of 11.00 MeV Au{sup 3+} ions implanted in FTO coated (thickness ≈300 nm) silicate glasses at varying fluence. • Metal clustering near the surface and subsurface region below glass-FTO interface changes electrical and optical properties significantly. • Ion implantation does not affect the crystalline structure of the coated films; however, the tetragonal distortion increases with increasing ion fluence. • Significant surface reconstruction takes place with ion beam fluence; The average roughness also decreases with increasing fluence. • The sheet resistivity increases with increasing fluence. • Raman analysis also corroborates the re-crystallization process inducing due to ion implantation. • Optical properties of the implanted surfaces changes significantly. - Abstract: Effects of 11.00 MeV Au{sup 3+} ions implanted in FTO coated (thickness ≈300 nm) silicate glasses on structural, electrical optical and phonon behavior have been explored. It has been observed that metal clustering near the surface and sub-surface region below glass-FTO interface changes electrical and optical properties significantly. Ion implantation does not affect the crystalline structure of the coated films; however, the unit cell volume decreases with increase in fluence and the tetragonal distortion (c/a ratio) also decreases systematically in the implanted samples. The sheet resistivity of the films increases from 11 × 10{sup −5} ohm-cm (in pristine) to 7.5 × 10{sup −4} ohm-cm for highest ion beam fluence ≈10{sup 15} ions/cm{sup 2}. The optical absorption decreases with increasing fluence whereas, the optical transmittance as well as reflectance increases with increasing fluence. The Raman spectra are observed at ∼530 cm{sup −1} and ∼1103 cm{sup −1} in pristine sample. The broad band at 530 cm{sup −1} shifts towards higher wave number in the irradiated samples. This may be correlated with increased disorder and strain relaxation in

  11. Modification of structure and optical band-gap of nc-Si:H films with ion irradiation

    Science.gov (United States)

    Zhu, Yabin; Wang, Zhiguang; Sun, Jianrong; Yao, Cunfeng; Shen, Tielong; Li, Bingsheng; Wei, Kongfang; Pang, Lilong; Sheng, Yanbin; Cui, Minghuan; Li, Yuanfei; Wang, Ji; Zhu, Huiping

    2012-09-01

    Hydrogenated nano-crystalline silicon (nc-Si:H) films fabricated by using hot-wire chemical vapor deposition are irradiated at room temperature with 6.0 MeV Xe-ions. The irradiation fluences are 1.0 × 1013, 5.0 × 1013 and 1.0 × 1014 Xe-ions/cm2. The structure and optical band-gap of the irradiated films varying with ion fluence are investigated by means of X-ray diffraction, Raman and UV-Vis-NIR spectroscopes, as well as transmission electron microscopy. It is found that the crystallite size, the crystalline fraction and the optical band-gap decrease continuously with increasing the ion fluence. The crystalline fraction of the films irradiated to the fluences from 0 to 1.0 × 1014 Xe-ions/cm2 decreases from about 65.7% to 2.9% and the optical band-gap decreases from about 2.1 to 1.6 eV. Possible origins of the modification of the nc-Si:H films under 6.0 MeV Xe-ions irradiation are briefly discussed.

  12. Effect of Co2+ Ions Doping on the Structural and Optical Properties of Magnesium Aluminate

    Science.gov (United States)

    Kanwal, Kiran; Ismail, Bushra; Rajani, K. S.; Kissinger, N. J. Suthan; Zeb, Aurang

    2017-07-01

    Cobalt-doped nanosized magnesium aluminate (Mg1-xCoxAl2O4) samples having different compositions ( x = 0.2, 0.4, 0.6, 0.8, 1.0) were synthesized by a chemical co-precipitation method. All samples were characterized by means of x-ray diffraction (XRD), scanning electron microscopy, Fourier transform infrared spectroscopy, ultra violet-visible spectroscopy, photoluminescence and diffused reflectance spectroscopy. The results of XRD revealed that the samples were spinel single phase cubic close packed crystalline materials. The lattice constant and x-ray density were found to be affected by the ionic radii of the doped metal cations. Using the Debye-Scherrer formula, the calculated crystalline size was found to be Co2+ ion concentration-dependent and varied between 32 nm and 40 nm. Nano-dimensions and phase of the Mg1-xCoxAl2O4 samples were analyzed and the replacement of Mg2+ ions with Co2+ ions was confirmed by elemental analysis. Three strong absorption bands at 540 nm, 580 nm and 630 nm were observed for the doped samples which are attributed to the three spin-allowed 4T1g (4F) → 4T2g, 4A2g, 4T1g (4P) electronic transitions of Co2+ at tetrahedral lattice sites. Nanophosphors have optical properties different from bulk because of spatial confinement and non-radiative relaxation. Decreases in particle size can increase the surface area and the defects, which can in turn increase the luminescent efficiency to make it very useful for tunable laser operations, persistent phosphorescence, color centers, photoconductivity and luminescence for display technology. MgAl2O4 was doped with Co2+ ions using a co-precipitation method and the optical absorption studies revealed that there is a decrease of band gap due to the increase of Co2+ content. The emission intensity of this phosphor is observed at 449 nm with a sharp peak attributed to the smaller size of the particles and the homogeneity of the powder.

  13. Highly selective and sensitive determination of copper ion by two novel optical sensors

    Directory of Open Access Journals (Sweden)

    Mehrorang Ghaedi

    2017-05-01

    Full Text Available New optical sensors for the determination of copper ion by incorporation of 1,1′-(4-nitro-1,2-phenylenebis(azan-1-yl-1-ylidenebis(methan-1-yl-1-lidenedinaphthalen-2-ol(L1, 1,1′-2,2′-(1,2-phenylenebis(ethene-2,1-diyldinaphthalen-2-ol 1(L2, dibutylphthalate (DBP and sodium tetraphenylborate (Na-TPB to the plasticized polyvinyl chloride matrices were prepared. The tendency of both ionophores (L2 and L1 as chromoionophore was significantly enhanced by the addition of DBP to the membrane. The proposed sensors benefit from advantages such as high stability, reproducibility and relatively long lifetime, good selectivity for Cu2+ ion determination over a large number of alkali, alkaline earth, transition and heavy metal ions. At optimum values of membrane compositions and experimental conditions, both sensors’ response was linear over a concentration range of 7.98 × 10−6 to 1.31 × 10−4mol L−1 and 1.99 × 10−6 to 5.12 × 10−5 mol L−1 for L2 and L1, respectively. Sensor detection limit based on the definition that the concentration of the sample leads to a signal equal to the blank signal plus three times of its standard deviation was found to be 3.99 × 10−7 and 5.88 × 10−7 mol L−1 for L2 and L1, respectively. The response time of the optodes (defined as the time required reaching the 90% of the peak signal was found to be 5–8 min for L2 and 20–25 min for L1 based sensor. The proposed optical sensors were applied successfully for the determination of Cu2+ ion content in water samples.

  14. Effect of VO2+ ions on the EPR and optical absorption investigations of lithium sulphate monohydrate single crystals for non linear optical applications

    Science.gov (United States)

    Juliet sheela, K.; Radha Krishnan, S.; Shanmugam, V. M.; Subramanian, P.

    2017-09-01

    Electron paramagnetic resonance (EPR) and optical absorption studies of VO2+ ions in Lithium Sulphate Monohydrate (LSMH) single crystal are carried out at room temperature. Single crystal rotations in each of the three mutually orthogonal crystalline planes, ac, ab, cb indicate three different vanadyl complexes. Three VO2+ ions of EPR spectra indicate among them, that two of them have (the intense two) entered the lattice substitutionally and the third one occupies the interstitial position. From the angular variation, the spin Hamiltonian parameters are evaluated. From the optical absorption spectrum containing four selected bands and EPR data, various bonding parameters are determined and the nature of bonding in the crystal is discussed. Also Second Harmonic Generation (SHG) studies are carried out to confirm the Non Linear Optical (NLO) properties of the given material.

  15. Characterization of ion-assisted induced absorption in A-Si thin-films used for multivariate optical computing

    Science.gov (United States)

    Nayak, Aditya B.; Price, James M.; Dai, Bin; Perkins, David; Chen, Ding Ding; Jones, Christopher M.

    2015-06-01

    Multivariate optical computing (MOC), an optical sensing technique for analog calculation, allows direct and robust measurement of chemical and physical properties of complex fluid samples in high-pressure/high-temperature (HP/HT) downhole environments. The core of this MOC technology is the integrated computational element (ICE), an optical element with a wavelength-dependent transmission spectrum designed to allow the detector to respond sensitively and specifically to the analytes of interest. A key differentiator of this technology is it uses all of the information present in the broadband optical spectrum to determine the proportion of the analyte present in a complex fluid mixture. The detection methodology is photometric in nature; therefore, this technology does not require a spectrometer to measure and record a spectrum or a computer to perform calculations on the recorded optical spectrum. The integrated computational element is a thin-film optical element with a specific optical response function designed for each analyte. The optical response function is achieved by fabricating alternating layers of high-index (a-Si) and low-index (SiO2) thin films onto a transparent substrate (BK7 glass) using traditional thin-film manufacturing processes (e.g., ion-assisted e-beam vacuum deposition). A proprietary software and process are used to control the thickness and material properties, including the optical constants of the materials during deposition to achieve the desired optical response function. The ion-assisted deposition is useful for controlling the densification of the film, stoichiometry, and material optical constants as well as to achieve high deposition growth rates and moisture-stable films. However, the ion-source can induce undesirable absorption in the film; and subsequently, modify the optical constants of the material during the ramp-up and stabilization period of the e-gun and ion-source, respectively. This paper characterizes the unwanted

  16. Structural and optical properties of low energy nitrogen ion implanted SrTiO3 thin films

    Science.gov (United States)

    Kumar, Vishnu; Asokan, K.; Annapoorni, S.

    2017-05-01

    The effect of 60 keV nitrogen ion implantation on the structural and optical properties of strontium titanate, SrTiO3 (STO) thin films were investigated as a function of ion fluences. These thin films were deposited on quartz substrates using RF magnetron sputtering and annealed at 750 °C for 5 hours. It was observed that the intensity of the X-Ray Diffraction (XRD) peaks increase at lower ion fluence and then decrease at higher ion fluences. The band gap derived from the UV-Visible spectrum of annealed pristine film was estimated to be 3.62 eV. A slight increase in the band gap was observed after N ion implantation.

  17. Effect of heavy ion irradiation on optical property of radiation-crosslinked hydroxypropyl cellulose gel containing methacrylate monomers

    Energy Technology Data Exchange (ETDEWEB)

    Hiroki, A. [Quantum Beam Science Center, Japan Atomic Energy Agency, 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Yamashita, S. [Nuclear Professional School, School of Engineering, The University of Tokyo, 2-22 Shirakata-shirane, Tokai-mura, Naka-gun, Ibaraki 319-1188 (Japan); Kimura, A.; Nagasawa, N.; Taguchi, M. [Quantum Beam Science Center, Japan Atomic Energy Agency, 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan)

    2015-12-15

    Effects of dose rate and liner energy transfer (LET) on the optical property of a polymer gel dosimeter irradiated with swift heavy ions were investigated. The polymer gel dosimeters that consist of 2-hydroxyethyl methacrylate, polyethylene glycol dimethacrylate, and tetrakis(hydroxymethyl)phosphonium chloride with radiation-crosslinked hydroxypropyl cellulose gel matrix were prepared. The dosimeters were irradiated with 150 MeV/u He ions, 290 MeV/u C ions, and 500 MeV/u Fe ions at HIMAC, and then were optically analyzed by using a UV–Vis spectrophotometer. Absorbance of the irradiated dosimeters increased with an increase in the dose up to 10 Gy. The absorbance at the dose of 5 Gy decreased with increasing dose rate in all of the heavy ions. The dosimeter irradiated with Fe ions exhibited the lowest dose response of the absorbance. It was found that the sensitivity of the dosimeters decreased with increasing dose rate as well as LET of the incident heavy ions.

  18. Effect of heavy ion irradiation on optical property of radiation-crosslinked hydroxypropyl cellulose gel containing methacrylate monomers

    Science.gov (United States)

    Hiroki, A.; Yamashita, S.; Kimura, A.; Nagasawa, N.; Taguchi, M.

    2015-12-01

    Effects of dose rate and liner energy transfer (LET) on the optical property of a polymer gel dosimeter irradiated with swift heavy ions were investigated. The polymer gel dosimeters that consist of 2-hydroxyethyl methacrylate, polyethylene glycol dimethacrylate, and tetrakis(hydroxymethyl)phosphonium chloride with radiation-crosslinked hydroxypropyl cellulose gel matrix were prepared. The dosimeters were irradiated with 150 MeV/u He ions, 290 MeV/u C ions, and 500 MeV/u Fe ions at HIMAC, and then were optically analyzed by using a UV-Vis spectrophotometer. Absorbance of the irradiated dosimeters increased with an increase in the dose up to 10 Gy. The absorbance at the dose of 5 Gy decreased with increasing dose rate in all of the heavy ions. The dosimeter irradiated with Fe ions exhibited the lowest dose response of the absorbance. It was found that the sensitivity of the dosimeters decreased with increasing dose rate as well as LET of the incident heavy ions.

  19. Nanosecond optical transmission studies of laser annealing in ion-implanted silicon-on-sapphire

    Energy Technology Data Exchange (ETDEWEB)

    Lee, M.C.; Lo, H.W.; Aydinli, A.; Trott, G.J.; Compaan, A. (Kansas State Univ., Manhattan (USA). Dept. of Physics); Hale, E.B. (Missouri Univ., Rolla (USA). Dept. of Physics)

    1983-06-01

    Time-resolved optical transmission has been studied using 633 and 514 nm CW probes on ion-implantation-amorphized silicon-on-sapphire during annealing by a 10 nsec, approximately 1 J/cm/sup 2/ pulse at either 532 nm or 485 nm. As recrystallization sets in the transmitted signal at 514 nm rises by approximately 10/sup 3/ in approximately 60 nsec and provides a measure of regrowth velocity. Beyond 200 nsec the much slower transmission rise is used to provide an estimate of the Si cooling rate. The difference in transmission observed between initially crystalline and initially amorphous Si provide an estimate of the latent heat of recrystallization of the amorphous phase.

  20. Optical and magnetic measurements of gyroscopically stabilized graphene nanoplatelets levitated in an ion trap

    Science.gov (United States)

    Nagornykh, Pavel; Coppock, Joyce E.; Murphy, Jacob P. J.; Kane, B. E.

    2017-07-01

    Using optical measurements, we demonstrate that the rotation of micron-scale graphene nanoplatelets levitated in a quadrupole ion trap in high vacuum can be frequency-locked to an applied radiofrequency electric field Erf. Over time, frequency-locking stabilizes the nanoplatelet so that its axis of rotation is normal to the nanoplatelet and perpendicular to Erf. We observe that residual slow dynamics of the direction of the axis of rotation in the plane normal to Erf is determined by an applied magnetic field. We present a simple model that accurately describes our observations. From our data and model, we can infer both a diamagnetic polarizability and a magnetic moment proportional to the frequency of rotation, which we compare to theoretical values. Our results establish that trapping technologies have applications for materials measurements at the nanoscale.

  1. Influence of rare earth ions on microstructural and optical properties of ZnO nanostructures

    Energy Technology Data Exchange (ETDEWEB)

    Riyajuddin, Sk., E-mail: riyaj5303@gmail.com; Ahmad, Shabbir; Faizan, M. [Department of Physics, Aligarh Muslim University, Aligarh 202002 (India); Naseem, Swaleha; Khan, Wasi; Naqvi, A. H. [Centre of Excellence in Materials Science (Nanomaterials), Department of Applied Physics, Z.H. College of Engg. & Technology, Aligarh Muslim University, Aligarh 202002 (India)

    2016-05-23

    Pure and 3% rare earth ions (Nd{sup 3+} & Gd{sup 3+}) doped ZnO samples were synthesized by sol-gel method, followed by annealing at temperature 450°C for 2hr. The samples were characterized by XRD, FTIR and UV-visible spectroscopy. XRD result confirmed single phase nature of all samples with crystalline structure. The average crystallite size of the doped samples found to be decreases as caculated using Debye-Scherrer’s formula. FTIR spectra indicate absorption band centered at 464 cm{sup −1} which is attributed to Zn-O lattice vibration. It confirms the formaton of compounds. UV-visible spectroscopy was used to study the optical properties and band gap of the synthesised materials using Tauc’s relation.

  2. Influence of rare earth ions on microstructural and optical properties of ZnO nanostructures

    Science.gov (United States)

    Riyajuddin, Sk.; Naseem, Swaleha; Khan, Wasi; Ahmad, Shabbir; Faizan, M.; Naqvi, A. H.

    2016-05-01

    Pure and 3% rare earth ions (Nd3+ & Gd3+) doped ZnO samples were synthesized by sol-gel method, followed by annealing at temperature 450°C for 2hr. The samples were characterized by XRD, FTIR and UV-visible spectroscopy. XRD result confirmed single phase nature of all samples with crystalline structure. The average crystallite size of the doped samples found to be decreases as caculated using Debye-Scherrer's formula. FTIR spectra indicate absorption band centered at 464 cm-1 which is attributed to Zn-O lattice vibration. It confirms the formaton of compounds. UV-visible spectroscopy was used to study the optical properties and band gap of the synthesised materials using Tauc's relation.

  3. The ion beam sputtering facility at KURRI: Coatings for advanced neutron optical devices

    Energy Technology Data Exchange (ETDEWEB)

    Hino, Masahiro, E-mail: hino@rri.kyoto-u.ac.jp [Research Reactor Institute, Kyoto university, Kumatori, Osaka 590-0494 (Japan); Oda, Tatsuro [Department of Nuclear Engineering, Kyoto University, Kyoto 615-8540 (Japan); Kitaguchi, Masaaki [Center for Experimental Studies, KMI, Nagoya University, Nagoya 464-8602 (Japan); Yamada, Norifumi L. [Neutron Science Laboratory, High Energy Accelerator Research Organization, 203-1 Shirakata, Tokai, Ibaraki 319-1106 (Japan); Tasaki, Seiji [Department of Nuclear Engineering, Kyoto University, Kyoto 615-8540 (Japan); Kawabata, Yuji [Research Reactor Institute, Kyoto university, Kumatori, Osaka 590-0494 (Japan)

    2015-10-11

    We describe a film coating facility for the development of multilayer mirrors for use in neutron optical devices that handle slow neutron beams. Recently, we succeeded in fabricating a large neutron supermirror with high reflectivity using an ion beam sputtering system (KUR-IBS), as well as all neutron supermirrors in two neutron guide tubes at BL06 at J-PARC/MLF. We also realized a large flexible self-standing m=5 NiC/Ti supermirror and very small d-spacing (d=1.65 nm) multilayer sheets. In this paper, we present an overview of the performance and utility of non-magnetic neutron multilayer mirrors fabricated with the KUR-IBS.

  4. Optical Properties of Amorphous AlN Thin Films on Glass and Silicon Substrates Grown by Single Ion Beam Sputtering

    Science.gov (United States)

    Hajakbari, Fatemeh; Mojtahedzadeh Larijani, Majid; Ghoranneviss, Mahmood; Aslaninejad, Morteza; Hojabri, Alireza

    2010-09-01

    The structural and optical properties of aluminum nitride (AlN) films deposited on glass and silicon substrates by single ion beam sputtering technique have been investigated. The X-ray diffraction and Fourier transform infrared spectroscopy (FTIR) study revealed the formation of the amorphous phase of AlN. The optical characteristics of films, such as refractive index, extinction coefficient, and average thickness, were calculated by Swanepoel's method using transmittance measurements. The refractive index and average roughness values of the films increased with film thickness. Moreover, it was found that thickness augmentation leads to a decrease in optical band gap energy calculated using Tauc's relation.

  5. Generation of Laguerre Gaussian beams using spiral phase diffractive elements fabricated on optical fiber tips using focused ion beam milling

    Science.gov (United States)

    Rodrigues Ribeiro, R. S.; Dahal, P.; Guerreiro, A.; Jorge, P. A. S.; Viegas, J.

    2016-03-01

    In this work, spiral phase lenses fabricated on the tip of single mode optical fibers are reported. This allows tailoring the fundamental guided mode, a Gaussian beam, into a Laguerre - Gaussian profile without using additional optical elements. The lenses are fabricated using Focused Ion Beam milling, enabling high resolution in the manufacturing process. The phase profiles are evaluated and validated using an implementation of the Finite Differences Time Domain. The output optical intensity profiles matching the numerical simulations are presented and analyzed. Finally, results on cell trapping and manipulation are briefly described.

  6. Pd+ ions in NaCl single crystal: EPR and optical studies

    Science.gov (United States)

    Badalyan, A. G.; Polak, K.; Rosa, J.

    2003-01-01

    EPR and optical absorption of Pd centres in as grown NaCl single crystal are reported. The EPR spectra show that palladium forms the Pd+ centre with d(x2-y2) wave function in the ground state. This centre formation and the accompanying distortion give rise to a superhyperfine interaction of the Pd+ ion with the nuclei of the four Cl- ligands in the plane perpendicular to the C-4 Symmetry axis. The results of the fitting of axial spin Hamiltonian parameters to the experimentally observed spectra give the following values at 12 K: g(parallel to) =2.85, g(perpendicular to) congruent to 2.15, A(parallel to) 29.8 x 10(-4)cm(-1), A(perpendicular to) = 5.9 x 10(-4)cm(-1). When the temperature increases, lines are getting broader, their amplitude decreases and a single line with g-value of g = 2.38 at g = 1/3(g(parallel to)+ 2g(perpendicular to)) appears, which demonstrates the known Jahn-Teller behaviour of d(9) ions EPR spectra.

  7. Optical control of trimeric P2X receptors and acid-sensing ion channels.

    Science.gov (United States)

    Browne, Liam E; Nunes, João P M; Sim, Joan A; Chudasama, Vijay; Bragg, Laricia; Caddick, Stephen; North, R Alan

    2014-01-07

    P2X receptors are trimeric membrane proteins that function as ion channels gated by extracellular ATP. We have engineered a P2X2 receptor that opens within milliseconds by irradiation at 440 nm, and rapidly closes at 360 nm. This requires bridging receptor subunits via covalent attachment of 4,4'-bis(maleimido)azobenzene to a cysteine residue (P329C) introduced into each second transmembrane domain. The cis-trans isomerization of the azobenzene pushes apart the outer ends of the transmembrane helices and opens the channel in a light-dependent manner. Light-activated channels exhibited similar unitary currents, rectification, calcium permeability, and dye uptake as P2X2 receptors activated by ATP. P2X3 receptors with an equivalent mutation (P320C) were also light sensitive after chemical modification. They showed typical rapid desensitization, and they could coassemble with native P2X2 subunits in pheochromocytoma cells to form light-activated heteromeric P2X2/3 receptors. A similar approach was used to open and close human acid-sensing ion channels (ASICs), which are also trimers but are unrelated in sequence to P2X receptors. The experiments indicate that the opening of the permeation pathway requires similar and substantial movements of the transmembrane helices in both P2X receptors and ASICs, and the method will allow precise optical control of P2X receptors or ASICs in intact tissues.

  8. Post-Test Analysis of the Deep Space One Spare Flight Thruster Ion Optics

    Science.gov (United States)

    Anderson, John R.; Sengupta, Anita; Brophy, John R.

    2004-01-01

    The Deep Space 1 (DSl) spare flight thruster (FT2) was operated for 30,352 hours during the extended life test (ELT). The test was performed to validate the service life of the thruster, study known and identify unknown life limiting modes. Several of the known life limiting modes involve the ion optics system. These include loss of structural integrity for either the screen grid or accelerator grid due to sputter erosion from energetic ions striking the grid, sputter erosion enlargement of the accelerator grid apertures to the point where the accelerator grid power supply can no longer prevent electron backstreaming, unclearable shorting between the grids causes by flakes of sputtered material, and rouge hole formation due to flakes of material defocusing the ion beam. Grid gap decrease, which increases the probability of electron backstreaming and of arcing between the grids, was identified as an additional life limiting mechanism after the test. A combination of accelerator grid aperture enlargement and grid gap decrease resulted in the inability to prevent electron backstreaming at full power at 26,000 hours of the ELT. Through pits had eroded through the accelerator grid webbing and grooves had penetrated through 45% of the grid thickness in the center of the grid. The upstream surface of the screen grid eroded in a chamfered pattern around the holes in the central portion of the grid. Sputter deposited material, from the accelerator grid, adhered to the downstream surface of the screen grid and did not spall to form flakes. Although a small amount of sputter deposited material protruded into the screen grid apertures, no rouge holes were found after the ELT.

  9. Develop techniques for ion implantation of PLZT (lead-lanthanum-zirconate-titanate) for adaptive optics

    Energy Technology Data Exchange (ETDEWEB)

    Batishko, C.R.; Brimhall, J.L.; Pawlewicz, W.T.; Stahl, K.A.; Toburen, L.H.

    1987-07-01

    Research was conducted at Pacific Northwest Laboratory to develop high photosensitivity adaptive optical elements utilizing ion implanted lanthanum-doped lead-zirconate-titanate (PLZT). One centimeter square samples were prepared by implanting ferroelectric and anti-ferroelectric PLZT with a variety of species or combinations of species. These included Ne, O, Ni, Ne/Cr, Ne/Al, Ne/Ni, Ne/O, and Ni/O, at a variety of energies and fluences. An indium-tin oxide (ITO) electrode coating was designed to give a balance of high conductivity and optical transmission at near uv to near ir wavelengths. Samples were characterized for photosensitivity; implanted layer thickness, index of refraction, and density; electrode (ITO) conductivity; and in some cases, residual stress curvature. Thin film anti-ferroelectric PLZT was deposited in a preliminary experiment. The structure was amorphous with x-ray diffraction showing the beginnings of a structure at substrate temperatures of approximately 550/sup 0/C. This report summarizes the research and provides a sampling of the data taken during the report period.

  10. Influence of europium (Eu3+) ions on the optical properties of silver lead borate glasses

    Indian Academy of Sciences (India)

    K Keshavamurthy; B Eraiah

    2015-09-01

    The influence of europium (Eu3+) ions on the optical properties of silver lead borate glasses of the Eu2O3–(1 – )Ag2O–29PbO–70B2O3 ( = 0, 0.1, 0.2, 0.3, 0.4 and 0.5 mol%) glass system prepared by the conventional melt quenching technique and their physical and optical properties were investigated. The UV absorption spectra were recorded at room temperature in the wavelength range of 200–600 nm. From the absorption edge data, it is found that both the direct and indirect transitions and their values are ranging from 3.19 to 3.54 and 2.50 to 3.07 eV, respectively. The Urbach energy values for these glasses were found to be in the range of 0.39–0.52 eV. The refractive indices have also been evaluated with respect to different molar concentrations of Eu2O3 and their calculated values are ranging from 1.598 to 1.654.

  11. Influence of material removal programming on ion beam figuring of high-precision optical surfaces

    Science.gov (United States)

    Liao, Wenlin; Dai, Yifan; Xie, Xuhui

    2014-09-01

    Ion beam figuring (IBF) provides a nanometer/subnanometer precision fabrication technology for optical components, where the surface materials on highlands are gradually removed by the physical sputtering effect. In this deterministic method, the figuring process is usually divided into several iterations and the sum of the removed material in each iteration is expected to approach the ideally removed material as nearly as possible. However, we find that the material removal programming in each iteration would influence the surface error convergence of the figuring process. The influence of material removal programming on the surface error evolution is investigated through the comparative study of the contour removal method (CRM) and the geometric proportion removal method (PRM). The research results indicate that the PRM can maintenance the smoothness of the surface topography during the whole figuring process, which would benefit the stable operation of the machine tool and avoid the production of mid-to-high spatial frequency surface errors. Additionally, the CRM only has the corrective effect on the area above the contour line in each iteration, which would result in the nonuniform convergence of the surface errors in various areas. All these advantages distinguish PRM as an appropriate material removal method for ultraprecision optical surfaces.

  12. Mid-infrared continuous wave cavity ring down spectroscopy of molecular ions using an optical parametric oscillator

    NARCIS (Netherlands)

    Verbraak, H.; Ngai, A.K.Y.; Persijn, S.T.; Harren, F.J.M.; Linnartz, H.

    2007-01-01

    A sensitive infrared detection scheme is presented in which continuous wave cavity ring down spectroscopy is used to record rovibrational spectra of molecular ions in direct absorption through supersonically expanding planar plasma. A cw optical parametric oscillator is used as a light source and

  13. Analysis of the fine structure of Sn11 +-Sn14 + ions by optical spectroscopy in an electron-beam ion trap

    Science.gov (United States)

    Windberger, A.; Torretti, F.; Borschevsky, A.; Ryabtsev, A.; Dobrodey, S.; Bekker, H.; Eliav, E.; Kaldor, U.; Ubachs, W.; Hoekstra, R.; Crespo López-Urrutia, J. R.; Versolato, O. O.

    2016-07-01

    We experimentally re-evaluate the fine structure of Sn11 +-Sn14 + ions. These ions are essential in bright extreme-ultraviolet (EUV) plasma-light sources for next-generation nanolithography, but their complex electronic structure is an open challenge for both theory and experiment. We combine optical spectroscopy of magnetic dipole M 1 transitions, in a wavelength range covering 260 to 780 nm, with charge-state selective ionization in an electron beam ion trap. Our measurements confirm the predictive power of ab initio calculations based on Fock space coupled cluster theory. We validate our line identification using semiempirical cowan calculations with adjustable wave-function parameters. Available Ritz combinations further strengthen our analysis. Comparison with previous work suggests that line identifications in the EUV need to be revisited.

  14. Patterning of Spiral Structure on Optical Fiber by Focused-Ion-Beam Etching

    Science.gov (United States)

    Mekaru, Harutaka; Yano, Takayuki

    2012-06-01

    We produce patterns on minute and curved surfaces of optical fibers, and develop a processing technology for fabricating sensors, antennas, electrical circuits, and other devices on such patterned surfaces by metallization. A three-dimensional processing technology can be used to fabricate a spiral coil on the surface of cylindrical quartz materials, and then the microcoils can also be applied to capillaries of micro-fluid devices, as well as to receiver coils connected to a catheter and an endoscope of nuclear magnetic resonance imaging (MRI) systems used in imaging blood vessels. To create a spiral line pattern with a small linewidth on a full-circumference surface of an optical fiber, focused-ion-beam (FIB) etching was employed. Here, a simple rotation stage comprising a dc motor and an LR3 battery was built. However, during the development of a prototype rotation stage before finalizing a large-scale remodelling of our FIB etching system, a technical problem was encountered where a spiral line could not be processed without running into breaks and notches in the features. It turned out that the problem was caused by axis blur resulting from an eccentric spinning (or wobbling) of the axis of the fiber caused by its unrestrained free end. The problem was solved by installing a rotation guide and an axis suppression device onto the rotation stage. Using this improved rotation stage. we succeeded in the seamless patterning of 1-µm-wide features on the full-circumference surface of a 250-µm-diameter quartz optical fiber (QOF) by FIB etching.

  15. Optical properties of ion-beam-synthesized Au nanoparticles in SiO{sub 2} matrix

    Energy Technology Data Exchange (ETDEWEB)

    Hsieh, Chang-Lin [Institute of Nuclear Engineering and Science, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China); Oyoshi, Keiji [Quantum Beam Unit, National Institute for Materials Science, 3-13 Sakura, Tsukuba, Ibaraki 305-0003 (Japan); Chao, Der-Sheng [Nuclear Science and Technology Development Center, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China); Tsai, Hsu-Sheng [Institute of Nuclear Engineering and Science, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China); Hong, Wei-Lun [Quantum Beam Unit, National Institute for Materials Science, 3-13 Sakura, Tsukuba, Ibaraki 305-0003 (Japan); Department of Engineering and System Science, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China); Takeda, Yoshihiko [Quantum Beam Unit, National Institute for Materials Science, 3-13 Sakura, Tsukuba, Ibaraki 305-0003 (Japan); Liang, Jenq-Horng, E-mail: jhliang@ess.nthu.edu.tw [Institute of Nuclear Engineering and Science, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China); Department of Engineering and System Science, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China)

    2016-05-15

    In recent years, gold (Au) nanoparticles have been synthesized via various methods and used in optical and biomedical detection. Au nanoparticles contain some remarkable dimension-dependent optical properties due to surface plasmon resonance (SPR) in Au nanoparticles which causes high absorption in visible light regions. Since SPR in well-crystallized Au nanoparticles can enhance the local electromagnetic field, it is thus expected that greater efficiency in the photoluminescence (PL) originating from oxygen deficiency centers (ODC) can be achieved in Au-implanted SiO{sub 2} matrix. In order to demonstrate the enhancement of PL, Au nanoparticles were formed in SiO{sub 2} film using ion beam synthesis and their optical and microstructural properties were also investigated in this study. The results revealed that a clear absorption peak at approximately 530 nm was identified in the UV-Vis spectra and was attributed to SPR induced by Au nanoparticles in SiO{sub 2}. The SPR of Au nanoparticles is also dependent on thermal treatment conditions, such as post-annealing temperature and ambient. The Au nanoparticle-containing SiO{sub 2} film also displayed several distinctive peaks at approximately 320, 360, 460, and 600 nm in the PL spectra and were found to be associated with ODC-related defects and non-bridging oxygen hole centers (NBOHC) in SiO{sub 2}. In addition, the PL peak intensities increased as post-annealing temperature increased, a finding contradictory to the defect recovery but highly consistent with the SPR tendency. A maximum PL emission was achieved when the Au-implanted SiO{sub 2} film was annealed at 1100 °C for 1 h under N{sub 2}. Therefore, the existence of Au nanoparticles in SiO{sub 2} film can induce SPR effects as well as enhance PL emission resulting from defect-related luminescence centers.

  16. Application of red and near infrared emission from rare earth ions for radiation measurements based on optical fibers

    Energy Technology Data Exchange (ETDEWEB)

    Takada, E.; Hosono, Y.; Takahashi, H.; Nakazawa, M. [Univ. of Tokyo (Japan). Dept. of Quantum Engineering and Systems Science; Kakuta, T. [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan); Yamazaki, M. [Sumita Optical Glass, Inc., Urawa, Saitama (Japan)

    1998-06-01

    When optical fiber radiation measurements are applied for a high dose rate area, there has been a problem of radiation induced loss in the optical fibers. In this study, red and near infrared (IR) fluorescence from rare earth ions has been used to reduce the problem. From continuous measurements using Gd{sub 2}O{sub 2}S:Pr{sup 3+}, the superiority of using long wavelength emission has been shown from the view point of radiation hardness. Linear relation between dose rate and peak counts was confirmed and it shows the possibility of using the long wavelength emission for radiation measurements. For calibration of the radiation induced loss, the Optical Time Domain Reflectometry (OTDR) technique has been applied. It has been shown that this method can broaden the dose rate limit of the optical fiber based measurements. Also, glass samples doped with rare-earth ions have been made and irradiated by gamma rays. Emission at longer wavelength than 700 nm has been observed for Eu{sup 3+} ions doped into silica, fluorophosphate and ZBLAN glass samples. Considering that it is easy to make silica glass and to connect it to usual silica glass optical fiber, silica glass doped with Eu{sup 3+} is thought to be the most promising material for new scintillating fibers with high radiation resistivity.

  17. Influence of 400 keV carbon ion implantation on structural, optical and electrical properties of PMMA

    Energy Technology Data Exchange (ETDEWEB)

    Arif, Shafaq, E-mail: sarif2005@gmail.com [Department of Physics, Lahore College for Women University, Lahore 54000 (Pakistan); Rafique, M. Shahid [Department of Physics, University of Engineering & Technology, Lahore 54000 (Pakistan); Saleemi, Farhat; Sagheer, Riffat [Department of Physics, Lahore College for Women University, Lahore 54000 (Pakistan); Naab, Fabian; Toader, Ovidiu [Department of Nuclear Engineering and Radiological Sciences, Michigan Ion Beam Laboratory, University of Michigan, MI 48109-2104 (United States); Mahmood, Arshad; Rashid, Rashad [National Institute of Lasers and Optronics (NILOP), P.O. Nilore, Islamabad (Pakistan); Mahmood, Mazhar [Department of Metallurgy & Materials Engineering, Pakistan Institute of Engineering & Applied Sciences (PIEAS), Islamabad (Pakistan)

    2015-09-01

    Ion implantation is a useful technique to modify surface properties of polymers without altering their bulk properties. The objective of this work is to explore the 400 keV C{sup +} ion implantation effects on PMMA at different fluences ranging from 5 × 10{sup 13} to 5 × 10{sup 15} ions/cm{sup 2}. The surface topographical examination of irradiated samples has been performed using Atomic Force Microscope (AFM). The structural and chemical modifications in implanted PMMA are examined by Raman and Fourier Infrared Spectroscopy (FTIR) respectively. The effects of carbon ion implantation on optical properties of PMMA are investigated by UV–Visible spectroscopy. The modifications in electrical conductivity have been measured using a four point probe technique. AFM images reveal a decrease in surface roughness of PMMA with an increase in ion fluence from 5 × 10{sup 14} to 5 × 10{sup 15} ions/cm{sup 2}. The existence of amorphization and sp{sup 2}-carbon clusterization has been confirmed by Raman and FTIR spectroscopic analysis. The UV–Visible data shows a prominent red shift in absorption edge as a function of ion fluence. This shift displays a continuous reduction in optical band gap (from 3.13 to 0.66 eV) due to formation of carbon clusters. Moreover, size of carbon clusters and photoconductivity are found to increase with increasing ion fluence. The ion-induced carbonaceous clusters are believed to be responsible for an increase in electrical conductivity of PMMA from (2.14 ± 0.06) × 10{sup −10} (Ω-cm){sup −1} (pristine) to (0.32 ± 0.01) × 10{sup −5} (Ω-cm){sup −1} (irradiated sample)

  18. Physical and optical absorption studies of Fe{sup 3+} - ions doped lithium borate glasses containing certain alkaline earths

    Energy Technology Data Exchange (ETDEWEB)

    Bhogi, Ashok [VNR Vignana Jyothi Institute of Engineering and Technology, Hyderabad, Telangana (India); Kumar, R. Vijaya [School of Physics, University of Hyderabad, Hyderabad, Telangana (India); Kistaiah, P., E-mail: pkistaiah@yahoo.com [Department of Physics, Osmania University, Hyderabad, Telangana (India)

    2016-05-23

    Iron ion doped lithium borate glasses with the composition 15RO-25Li{sub 2}O-59B{sub 2}O{sub 3}-1Fe{sub 2}O{sub 3} (where R= Ca, Sr and Ba) have been prepared by the conventional melt quenching technique and characterized to investigate the physical and optical properties using XRD, density, molar volume and UV-Visible spectroscopy. The optical absorption spectra exhibit a band at around 460 nm which is assigned to {sup 6}A{sub 1g}(S) → 4E{sub g} (G) of Fe{sup 3+} ions with distorted octahedral symmetry. From ultraviolet absorption edges, the optical band gap and Urbach energies have been evaluated. The effect of alkaline earths on these properties is discussed.

  19. Physical and optical absorption studies of Fe3+ - ions doped lithium borate glasses containing certain alkaline earths

    Science.gov (United States)

    Bhogi, Ashok; Kumar, R. Vijaya; Kistaiah, P.

    2016-05-01

    Iron ion doped lithium borate glasses with the composition 15RO-25Li2O-59B2O3-1Fe2O3 (where R= Ca, Sr and Ba) have been prepared by the conventional melt quenching technique and characterized to investigate the physical and optical properties using XRD, density, molar volume and UV-Visible spectroscopy. The optical absorption spectra exhibit a band at around 460 nm which is assigned to 6A1g(S) → 4Eg (G) of Fe3+ ions with distorted octahedral symmetry. From ultraviolet absorption edges, the optical band gap and Urbach energies have been evaluated. The effect of alkaline earths on these properties is discussed.

  20. Optical and structural properties of 100 MeV Fe{sup 9+} ion irradiated InP

    Energy Technology Data Exchange (ETDEWEB)

    Dubey, R. L., E-mail: radhekrishna.dubey@xaviers.edu [Department of Physics, St. Xavier’s College-Autonomous, Mumbai-400 001 (India); Department of Physics, University of Mumbai, Mumbai-400 032 (India); Dubey, S. K. [Department of Physics, University of Mumbai, Mumbai-400 032 (India); Bodhane, S. P. [Department of Physics, St. Xavier’s College-Autonomous, Mumbai-400 001 (India); Kanjilal, D. [Inter University Accelerator Centre, ArunaAsaf Ali, Marg,New Delhi-110 067 (India)

    2016-05-06

    Single crystal InP samples were irradiated with 100 MeV Fe{sup 9+} ions for ion fluences 1x10{sup 12} and 1x10{sup 13} cm{sup −2}. Optical properties of irradiated InP was investigated by Spectroscopic Ellipsometry and UV-VIS-NIR spectroscopy. The optical parameters like, refractive index, extinction coefficient, absorption coefficient is found to be fluence dependent near the surface as well as near the projected range. Small change in the optical parameters near the surface region as investigated by Spectroscopic Ellipsometry indicatesthat the surfaces of irradiated InP are similar to non-irradiated InP. This is also supported by RBS/C measurements. The UV-VIS-NIR study revealed the decrease in the band gap and increase in the defect concentration in the irradiated sample as a result of nuclear energy loss.

  1. Functional implications of species differences in the size and morphology of the isthmo optic nucleus (ION) in birds.

    Science.gov (United States)

    Gutiérrez-Ibáñez, Cristián; Iwaniuk, Andrew N; Lisney, Thomas J; Faunes, Macarena; Marín, Gonzalo J; Wylie, Douglas R

    2012-01-01

    In birds, there is a retinofugal projection from the brain to the retina originating from the isthmo optic nucleus (ION) in the midbrain. Despite a large number of anatomical, physiological and histochemical studies, the function of this retinofugal system remains unclear. Several functions have been proposed including: gaze stabilization, pecking behavior, dark adaptation, shifting attention, and detection of aerial predators. This nucleus varies in size and organization among some species, but the relative size and morphology of the ION has not been systematically studied. Here, we present a comparison of the relative size and morphology of the ION in 81 species of birds, representing 17 different orders. Our results show that several orders of birds, besides those previously reported, have a large, well-organized ION, including: hummingbirds, woodpeckers, coots and allies, and kingfishers. At the other end of the spectrum, parrots, herons, waterfowl, owls and diurnal raptors have relatively small ION volumes. ION also appears to be absent or unrecognizable is several taxa, including one of the basal avian groups, the tinamous, which suggests that the ION may have evolved only in the more modern group of birds, Neognathae. Finally, we demonstrate that evolutionary changes in the relative size and the cytoarchitectonic organization of ION have occurred largely independent of phylogeny. The large relative size of the ION in orders with very different lifestyles and feeding behaviors suggest there is no clear association with pecking behavior or predator detection. Instead, our results suggest that the ION is more complex and enlarged in birds that have eyes that are emmetropic in some parts of the visual field and myopic in others. We therefore posit that the ION is involved in switching attention between two parts of the retina i.e. from an emmetropic to a myopic part of the retina.

  2. Functional implications of species differences in the size and morphology of the isthmo optic nucleus (ION in birds.

    Directory of Open Access Journals (Sweden)

    Cristián Gutiérrez-Ibáñez

    Full Text Available In birds, there is a retinofugal projection from the brain to the retina originating from the isthmo optic nucleus (ION in the midbrain. Despite a large number of anatomical, physiological and histochemical studies, the function of this retinofugal system remains unclear. Several functions have been proposed including: gaze stabilization, pecking behavior, dark adaptation, shifting attention, and detection of aerial predators. This nucleus varies in size and organization among some species, but the relative size and morphology of the ION has not been systematically studied. Here, we present a comparison of the relative size and morphology of the ION in 81 species of birds, representing 17 different orders. Our results show that several orders of birds, besides those previously reported, have a large, well-organized ION, including: hummingbirds, woodpeckers, coots and allies, and kingfishers. At the other end of the spectrum, parrots, herons, waterfowl, owls and diurnal raptors have relatively small ION volumes. ION also appears to be absent or unrecognizable is several taxa, including one of the basal avian groups, the tinamous, which suggests that the ION may have evolved only in the more modern group of birds, Neognathae. Finally, we demonstrate that evolutionary changes in the relative size and the cytoarchitectonic organization of ION have occurred largely independent of phylogeny. The large relative size of the ION in orders with very different lifestyles and feeding behaviors suggest there is no clear association with pecking behavior or predator detection. Instead, our results suggest that the ION is more complex and enlarged in birds that have eyes that are emmetropic in some parts of the visual field and myopic in others. We therefore posit that the ION is involved in switching attention between two parts of the retina i.e. from an emmetropic to a myopic part of the retina.

  3. Electron spin resonance and optical absorption spectroscopic studies of Cu{sup 2+} ions in aluminium lead borate glasses

    Energy Technology Data Exchange (ETDEWEB)

    SivaRamaiah, G., E-mail: gsivaram7@yahoo.co.in [Department of Physics, Government College for Men, Kadapa 516004 (India); LakshmanaRao, J., E-mail: jlrao46@yahoo.co.in [Department of Physics, Sri Venkateswara University, Tirupati 517502 (India)

    2013-02-25

    Highlights: Black-Right-Pointing-Pointer It is for the first time to study optical absorption and EPR in these glasses. Black-Right-Pointing-Pointer The thermal properties are new and interesting in this glass system. Black-Right-Pointing-Pointer It is for the first time to report three optical bands for Cu{sup 2+} in oxide glasses. Black-Right-Pointing-Pointer The interesting optical results are due to excellent sample preparation. - Abstract: Electron Spin Resonance and optical absorption spectral studies of Cu{sup 2+} ions in 5 Al{sub 2}O{sub 3} + 75 B{sub 2}O{sub 3} + (20-z) PbO + z CuO (where z = 0.1-1.5 mol.% of CuO) glasses have been reported. The EPR spectra of all the glasses show resonance signals characteristic of Cu{sup 2+} ions at both room and low temperatures. The number of spins and Gibbs energy were calculated at different concentrations and temperatures. From the plot of the ratio of logarithmic number of spins and absolute temperature and the reciprocal of absolute temperature, the entropy and enthalpy have been evaluated. The optical absorption spectra of all the glasses exhibit three bands and these bands have been assigned to {sup 2}B{sub 1g} {yields} {sup 2}E{sub g}, {sup 2}B{sub 1g} {yields} {sup 2}B{sub 2g}, and {sup 2}B{sub 1g} {yields} {sup 2}A{sub 1g} transitions in the decreasing order of energy. It is for the first time to observe three optical absorption bands for Cu{sup 2+} ions in oxide glasses. Such type of results is due to excellent sample preparation. From the EPR and optical absorption spectroscopies data, the molecular orbital coefficients have been evaluated.

  4. Swift heavy ion induced optical and structural modifications in RF sputtered nanocrystalline ZnO thin film

    Science.gov (United States)

    Singh, S. K.; Singhal, R.; Vishnoi, R.; Kumar, V. V. S.; Kulariya, P. K.

    2017-01-01

    In the present study, 100 MeV Ag7+ ion beam-induced structural and optical modifications of nanocrystalline ZnO thin films are investigated. The nanocrystalline ZnO thin films are grown using radio frequency magnetron sputtering and irradiated at fluences of 3 × 1012, 1 × 1013 and 3 × 1013 ions/cm2. The incident swift heavy ions induced change in the crystallinity together with the preferential growth of crystallite size along the c axis (002) orientation. The average crystallite size is found to be increased from 10.8 ± 0.7 to 20.5 ± 0.3 nm with increasing the ion fluence. The Atomic force microscopy analysis confirms the variation in the surface roughness by varying the incident ion fluences. The UV-visible spectroscopy shows the decrement in transmittance of the film with ion irradiation. The micro-Raman spectra of ZnO thin films are investigated to observe ion-induced modifications which support the increased lattice defects with higher fluence. The variation in crystallinity indicates that ZnO-based devices can be used in piezoelectric transduction mechanism.

  5. The effect of nitrogen ion implantation on the structural, optical and electrical properties of ZnSe thin films

    Science.gov (United States)

    Venkatachalam, S.; Mangalaraj, D.; Narayandass, Sa K.; Kesavamoorthy, R.; Magudapathy, P.; Sundaravel, B.; Kalavathi, S.; Nair, K. G. M.

    2006-12-01

    Zinc selenide thin films were deposited onto well-cleaned glass and silicon substrates using the vacuum evaporation technique under a vacuum of 3 × 10-5 Torr. These films were implanted with mass-analysed 75 keV N+ ions at different doses ranging from 1014 to 1016 ions cm-2. The composition, microstructure, surface roughness, optical bandgap and electrical properties of the as-deposited and nitrogen-implanted films were studied by Rutherford backscattering (RBS), grazing incidence x-ray diffraction (GIXRD), atomic force microscopy (AFM), Raman scattering, optical transmittance and I-V measurements. The RBS analysis indicates that the composition of the as-deposited and nitrogen-implanted films is nearly stoichiometric. The thickness of the as-deposited film is calculated as 230 nm. The structure of the as-deposited and nitrogen-implanted thin films is cubic. In the AFM analysis, the surface roughness is found to increase with an increasing dose of nitrogen ions. In the optical studies, the optical bandgap value decreases with increase of the N+ dose. The prepared device exhibits a very good response in the visible region.

  6. Ion irradiation as a tool for modifying the surface and optical properties of plasma polymerised thin films

    Science.gov (United States)

    Grant, Daniel S.; Bazaka, Kateryna; Siegele, Rainer; Holt, Stephen A.; Jacob, Mohan V.

    2015-10-01

    Radio frequency (R.F.) glow discharge polyterpenol thin films were prepared on silicon wafers and irradiated with I10+ ions to fluences of 1 × 1010 and 1 × 1012 ions/cm2. Post-irradiation characterisation of these films indicated the development of well-defined nano-scale ion entry tracks, highlighting prospective applications for ion irradiated polyterpenol thin films in a variety of membrane and nanotube-fabrication functions. Optical characterisation showed the films to be optically transparent within the visible spectrum and revealed an ability to selectively control the thin film refractive index as a function of fluence. This indicates that ion irradiation processing may be employed to produce plasma-polymer waveguides to accommodate a variety of wavelengths. XRR probing of the substrate-thin film interface revealed interfacial roughness values comparable to those obtained for the uncoated substrate's surface (i.e., both on the order of 5 Å), indicating minimal substrate etching during the plasma deposition process.

  7. Magneto-optical mode conversion in a hybrid glass waveguide made by sol-gel and ion-exchange techniques

    Science.gov (United States)

    Royer, François; Amata, Hadi; Parsy, François; Jamon, Damien; Ghibaudo, Elise; Broquin, Jean-Emmanuel; Neveu, Sophie

    2012-01-01

    The integration of magneto-optical materials with classical technologies being still a difficult problem, this study explores the possibility to realize a mode converter based on a hybrid structure. A composite magneto-optical layer made of a silica/zirconia matrix doped by magnetic nanoparticles is coated on the top face of ion-exchanged glass waveguides. Optical characterizations that have been carried out demonstrated the efficiency of these hybrid structures in terms of lateral confinement. Furthermore, TE to TM mode conversion has been observed when a longitudinal magnetic field is applied to the device. The amount of this conversion is analysed taking into account the magneto-optical confinement and the modal birefringence of the structure.

  8. Sub-mm Scale Fiber Guided Deep/Vacuum Ultra-Violet Optical Source for Trapped Mercury Ion Clocks

    Science.gov (United States)

    Yi, Lin; Burt, Eric A.; Huang, Shouhua; Tjoelker, Robert L.

    2013-01-01

    We demonstrate the functionality of a mercury capillary lamp with a diameter in the sub-mm range and deep ultraviolet (DUV)/ vacuum ultraviolet (VUV) radiation delivery via an optical fiber integrated with the capillary. DUV spectrum control is observed by varying the fabrication parameters such as buffer gas type and pressure, capillary diameter, electrical resonator design, and temperature. We also show spectroscopic data of the 199Hg+ hyper-fine transition at 40.5GHz when applying the above fiber optical design. We present efforts toward micro-plasma generation in hollow-core photonic crystal fiber with related optical design and theoretical estimations. This new approach towards a more practical DUV optical interface could benefit trapped ion clock developments for future ultra-stable frequency reference and time-keeping applications.

  9. Sub-mm Scale Fiber Guided Deep/Vacuum Ultra-Violet Optical Source for Trapped Mercury Ion Clocks

    Science.gov (United States)

    Yi, Lin; Burt, Eric A.; Huang, Shouhua; Tjoelker, Robert L.

    2013-01-01

    We demonstrate the functionality of a mercury capillary lamp with a diameter in the sub-mm range and deep ultraviolet (DUV)/ vacuum ultraviolet (VUV) radiation delivery via an optical fiber integrated with the capillary. DUV spectrum control is observed by varying the fabrication parameters such as buffer gas type and pressure, capillary diameter, electrical resonator design, and temperature. We also show spectroscopic data of the 199Hg+ hyper-fine transition at 40.5GHz when applying the above fiber optical design. We present efforts toward micro-plasma generation in hollow-core photonic crystal fiber with related optical design and theoretical estimations. This new approach towards a more practical DUV optical interface could benefit trapped ion clock developments for future ultra-stable frequency reference and time-keeping applications.

  10. Effects of source temperature and characteristics on the optical emission from a gallium liquid metal ion source

    Energy Technology Data Exchange (ETDEWEB)

    Hornsey, R.I.; Marriott, P.

    1989-05-14

    The light emitted from the region close to the tip of an emitting liquid metal ion source has been observed. It is shown that at high currents the light intensity rises almost as the cube of the current, but that the optical emission also depends on the source characteristics. A model based on the break-up of charged droplets is proposed to account for these results, thermal evaporation being found to be insignificant. Measurements of the effects of source temperature on light emission are also presented. From these measurements it is demonstrated that field ionisation cannot be responsible for the distortion of the total ion energy distribution seen at elevated temperatures. (author).

  11. Noninvasive Vibrational Mode Spectroscopy of Ion Coulomb Crystals through Resonant Collective Coupling to an Optical Cavity Field

    DEFF Research Database (Denmark)

    Dantan, Aurélien; Marler, Joan; Albert, Magnus

    2010-01-01

    We report on a novel noninvasive method to determine the normal mode frequencies of ion Coulomb crystals in traps based on the resonance enhanced collective coupling between the electronic states of the ions and an optical cavity field at the single photon level. Excitations of the normal modes...... are observed through a Doppler broadening of the resonance. An excellent agreement with the predictions of a zero-temperature uniformly charged liquid plasma model is found. The technique opens up for investigations of the heating and damping of cold plasma modes, as well as the coupling between them....

  12. Fabrication of hard-coated optical absorbers with microstructured surfaces using etched ion tracks: Toward broadband ultra-low reflectance

    Energy Technology Data Exchange (ETDEWEB)

    Amemiya, Kuniaki, E-mail: k.amemiya@aist.go.jp [National Metrology Institute of Japan (NMIJ), National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, Ibaraki 305-8563 (Japan); Koshikawa, Hiroshi; Yamaki, Tetsuya; Maekawa, Yasunari [Quantum Beam Science Center, Japan Atomic Energy Agency (JAEA), 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Shitomi, Hiroshi; Numata, Takayuki; Kinoshita, Kenichi; Tanabe, Minoru; Fukuda, Daiji [National Metrology Institute of Japan (NMIJ), National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, Ibaraki 305-8563 (Japan)

    2015-08-01

    Highlights: • A hard-coated optical absorber with microstructured surface was fabricated. • Etched ion tracks coated with diamond-like carbon were used. • The reflectance was below 2% for wavelengths in the 400–1400 nm range. • Fabricated optical absorber exhibited temporal durability and mechanical stability. • Further improvement of the design and process will yield reflectance of ∼0.1%. - Abstract: Broadband low reflectance materials have various applications in the field of optical energy management; however, materials with ultra-low reflectance (below 0.1%) have been considered as mechanically delicate. We have developed a novel hard-surface optical absorber with microstructured, diamond-like carbon coated ion tracks on CR-39 plastic substrate. The spectral reflectance of the first prototype was below 2% for wavelengths ranging from 400 nm to 1400 nm; moreover, the optical absorber had mechanically hard surface and exhibited temporal durability. Choosing the appropriate design of the surface structure and coating layer is likely to reduce the reflectance to the order of 0.1%. This technique yields easy-to-handle broadband ultra-low reflectance absorbers.

  13. Investigations on optical properties of Sm{sup 3+} ion doped boro-phosphate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Vijayakumar, R.; Suthanthirakumar, P.; Karthikeyan, P.; Marimuthu, K., E-mail: mari-ram2000@yahoo.com [Department of Physics, Gandhigram Rural Institute – Deemed University, Gandhigram – 624302 (India)

    2015-06-24

    The Sm{sup 3+} doped Boro-phosphate glasses with the chemical composition 60H{sub 3}BO{sub 3}+20Li{sub 2}CO{sub 3}+10ZnO+(10−x) H{sub 6}NO{sub 4}P+xSm{sub 2}O{sub 3} (where x= 0.1, 0.5, 1 and 2 in wt%) have been prepared by melt quenching technique. The prepared glasses were characterized through optical absorption and luminescence spectral measurements. The band gap energies corresponding to the direct and indirect allowed transitions and the Urbach’s energy values were estimated from the absorption spectra. Judd-Ofelt intensity parameters have been derived to predict the radiative properties of the various emission transitions. In order to identify the emission color of the prepared glasses, the emission intensities were analyzed using CIE 1931 color chromaticity diagram. The energy transfer process takes place between Sm{sup 3+}−Sm{sup 3+} ions through cross-relaxation mechanism have also been investigated and the results were discussed and reported.

  14. Effect of silver ion-induced disorder on morphological, chemical and optical properties of poly (methyl methacrylate)

    Energy Technology Data Exchange (ETDEWEB)

    Arif, Shafaq, E-mail: sarif2005@gmail.com [Department of Physics, Lahore College for Women University, Lahore 54000 (Pakistan); Saleemi, Farhat [Department of Physics, Lahore College for Women University, Lahore 54000 (Pakistan); Rafique, M. Shahid [Department of Physics, University of Engineering & Technology, Lahore 54000 (Pakistan); Naab, Fabian; Toader, Ovidiu [Department of Nuclear Engineering and Radiological Sciences, Michigan Ion Beam Laboratory, University of Michigan, MI 48109-2104 (United States); Mahmood, Arshad; Aziz, Uzma [National Institute of Lasers & Optronics (NILOP), P.O. Nilore, Islamabad (Pakistan)

    2016-11-15

    Ion implantation is a versatile technique to tailor the surface properties of polymers in a controlled manner. In the present study, samples of poly (methyl methacrylate) (PMMA) have been implanted with 400 keV silver (Ag{sup +}) ion beam to various ion fluences ranging from 5 × 10{sup 13} to 5 × 10{sup 15} ions/cm{sup 2}. The effect of Ag{sup +} ion-induced disorder on morphological, chemical and optical properties of PMMA is analyzed using Atomic Force Microscope (AFM), Fourier transform infrared spectroscopy (FTIR) and ultraviolet–visible (UV–Vis) spectroscopy. Furthermore, the electrical conductivity of pristine and implanted PMMA is measured using four probe apparatus. The AFM images revealed the growth of nano-sized grainy structures and hillocks above the surface of implanted PMMA. The FTIR spectra confirmed the modifications in chemical structure of PMMA along with the formation of −C=C− carbon contents. The refractive index, extinction coefficient and photoconductivity of implanted PMMA have been found to increase as a function of ion fluence. Simultaneously, indirect optical band gap is reduced from 3.13 to 0.81 eV at a relatively high fluence (5 × 10{sup 15} ions/cm{sup 2}). A linear correlation has been established between the band gap and Urbach energies. Moreover, the electrical conductivity of Ag{sup +} implanted PMMA has increased from 2.14 × 10{sup −10} (pristine) to 9.6 × 10{sup −6} S/cm.

  15. Magnetic nanoparticles-doped silica layer reported on ion-exchanged glass waveguide: towards integrated magneto-optical devices

    Science.gov (United States)

    Amata, Hadi; Royer, François; Choueikani, Fadi; Jamon, Damien; Broquin, Jean-Emmanuel; Plenet, Jean Claude; Rousseau, Jean Jaques

    2010-05-01

    In the framework of optical telecommunication systems, many functions are integrated on the same substrate. Nevertheless, one of the most important, such as isolation, is achieved using discrete components. It is based on magnetic materials which are always difficult to integrate with classical technologies. This is due to the annealing temperature of magnetic materials. In this paper we present another way for the realisation of such components. We use a dip coating process to report a magnetic nanoparticles doped silica layer on ion-exchanged glass waveguide. The advantages of this method is discussed and we demonstrate its compatibility with ion-exchanged technology. By varying the refractive index of the layer, we can adjust the interaction between the waveguide and the magneto-optical layer.

  16. Auger electron spectroscopy, secondary ion mass spectroscopy and optical characterization of a-C-H and BN films

    Science.gov (United States)

    Pouch, J. J.; Alterovitz, S. A.; Warner, J. D.

    1986-01-01

    The amorphous dielectrics a-C:H and BN were deposited on III-V semiconductors. Optical band gaps as high as 3 eV were measured for a-C:H generated by C4H10 plasmas; a comparison was made with bad gaps obtained from films prepared by CH4 glow discharges. The ion beam deposited BN films exhibited amorphous behavior with band gaps on the order of 5 eV. Film compositions were studied by Auger electron spectroscopy (AES), x-ray photoelectron spectroscopy (XPS) and secondary ion mass spectrometry (SIMS). The optical properties were characterized by ellipsometry, UV/VIS absorption, and IR reflection and transmission. Etching rates of a-C:H subjected to O2 dicharges were determined.

  17. Buried waveguides for passive integrated optics by Cs+ -ion-exchange

    Science.gov (United States)

    Ross, L.; Lilienhof, H.-J.; Holscher, H. W.

    1986-11-01

    Cs4-ion-exchange in glass is compared with the commonly used K+-, Ag+- and T1+-ion-exchange in glass in the process of waveguide fabrication. It will be shown that the Cs4-ion-exchange in the special substrate glass BGG21 represents an alternative method. As in the case of Ag+ AND T14 it is possible to fabricate buried waveguides by a double ion-exchange. The field-assisted ion-exchange is preferred due to the low CO+-ion mobility.

  18. Functional Implications of Species Differences in the Size and Morphology of the Isthmo Optic Nucleus (ION) in Birds

    OpenAIRE

    Cristián Gutiérrez-Ibáñez; Iwaniuk, Andrew N.; Lisney, Thomas J.; Macarena Faunes; Marín, Gonzalo J.; Wylie, Douglas R.

    2012-01-01

    In birds, there is a retinofugal projection from the brain to the retina originating from the isthmo optic nucleus (ION) in the midbrain. Despite a large number of anatomical, physiological and histochemical studies, the function of this retinofugal system remains unclear. Several functions have been proposed including: gaze stabilization, pecking behavior, dark adaptation, shifting attention, and detection of aerial predators. This nucleus varies in size and organization among some species, ...

  19. Theoretical explanation of electron paramagnetic resonance and optical parameters for Cu2+ ion in LiNbO3 crystal

    Indian Academy of Sciences (India)

    S Ravi; P Subramanian

    2007-08-01

    The EPR parameters, anisotropic -factors , and for Cu2+ ion and hyperfine structure constants , and for Cu2+ in LiNbO3 crystal are calculated by the method of diagonalizing the full Hamiltonian matrix. The crystal-field parameters contact with the crystal structure by the aid of the superposition model. The optical transition parameters are calculated using Zhao crystal-field model. The calculated results are in good agreement with the observed values. The results are discussed.

  20. Optical Properties of Li2B4O7 Glasses Doped with Rare-Earths and Transition Metal Ions

    Science.gov (United States)

    2001-01-01

    K.P. O’Donnell, B. Henderson and D. Hollis, " Disorder and the optical spectroscopy of Cr 3+- doped glasses: II. Glasses with high and low ligand...ions in oxide compounds", Fiz. Tw. Tela, 31(1), pp. 243-249, 1989. 11. W. Chen, J.O. Maim, V. Zwiller, Y. Huang, S. Liu, R. Wallenberg , J.O. Bovin and L

  1. Optical transmittance investigation of 1-keV ion-irradiated sapphire crystals as potential VUV to NIR window materials of fusion reactors

    Directory of Open Access Journals (Sweden)

    Keisuke Iwano

    2016-10-01

    Full Text Available We investigate the optical transmittances of ion-irradiated sapphire crystals as potential vacuum ultraviolet (VUV to near-infrared (NIR window materials of fusion reactors. Under potential conditions in fusion reactors, sapphire crystals are irradiated with hydrogen (H, deuterium (D, and helium (He ions with 1-keV energy and ∼ 1020-m-2 s-1 flux. Ion irradiation decreases the transmittances from 140 to 260 nm but hardly affects the transmittances from 300 to 1500 nm. H-ion and D-ion irradiation causes optical absorptions near 210 and 260 nm associated with an F-center and an F+-center, respectively. These F-type centers are classified as Schottky defects that can be removed through annealing above 1000 K. In contrast, He-ion irradiation does not cause optical absorptions above 200 nm because He-ions cannot be incorporated in the crystal lattice due to the large ionic radius of He-ions. Moreover, the significant decrease in transmittance of the ion-irradiated sapphire crystals from 140 to 180 nm is related to the light scattering on the crystal surface. Similar to diamond polishing, ion irradiation modifies the crystal surface thereby affecting the optical properties especially at shorter wavelengths. Although the transmittances in the VUV wavelengths decrease after ion irradiation, the transmittances can be improved through annealing above 1000 K. With an optical transmittance in the VUV region that can recover through simple annealing and with a high transparency from the ultraviolet (UV to the NIR region, sapphire crystals can therefore be used as good optical windows inside modern fusion power reactors in terms of light particle loadings of hydrogen isotopes and helium.

  2. Effect of boron ion implantation on the structural, optical and electrical properties of ZnSe thin films

    Science.gov (United States)

    Venkatachalam, S.; Kanno, Yoshinori; Mangalaraj, D.; Narayandass, Sa. K.

    2007-03-01

    Zinc Selenide (ZnSe) thin films were deposited onto well cleaned glass substrates using vacuum evaporation technique under a vacuum of 3×10 -5 mbar. The prepared ZnSe samples were implanted with mass analyzed 75 keV B + ions at different doses ranging from 10 12 to 10 16 ions cm -2. The composition, thickness, microstructures, surface roughness and optical band gap of the as-deposited and boron-implanted films were studied by Rutherford backscattering (RBS), grazing incidence X-ray diffraction, Atomic force microscopy, Raman scattering and transmittance measurements. The RBS analysis indicates that the composition of the as-deposited and boron-implanted films is nearly stoichiometric. The thickness of the as-deposited film is calculated as 230 nm. The structure of the as-deposited and boron-implanted thin films is cubic. It is found that the surface roughness increases on increasing the dose of boron ions. In the optical studies, the optical band gap value decreases with an increase of boron concentration. In the electrical studies, the prepared device gave a very good response in the blue wavelength region.

  3. Optical emission spectroscopy of excited atoms sputtered on a Ti surface under irradiation with multicharged Ar ions

    Energy Technology Data Exchange (ETDEWEB)

    Motohashi, K [Department of Applied Physics, Tokyo University of Agriculture and Technology, 2-24-16 Koganei-shi, Tokyo 184-8588 (Japan); Saitoh, Y [Department of Advanced Radiation Technology, Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency (JAEA), Takasaki, Gunma 370-1292 (Japan); Kitazawa, S, E-mail: motohasi@cc.tuat.ac.j [Division of ITER Project, Fusion Research Development, Japan Atomic Energy Agency (JAEA), Naka, Ibaraki 311-0193 (Japan)

    2009-04-01

    Optical emission spectroscopy of excited atoms was carried out in order to investigate the sputtering processes on solid surfaces under irradiation of slow, multicharged ions. Many atomic lines of Ti I (neutral) and Ti II (single-charged ions) were observed in wavelengths from 250 to 750 nm with irradiation by Ar{sup 3+} (30 keV) on a Ti surface which was placed in a low pressure O{sub 2} atmosphere. The emission intensity of Ti I (520 nm) decreased monotonically with an increase of O{sub 2} partial pressure, whereas that of Ti I / II (670 nm, a 2nd order wavelength of 335 nm) slightly increased. From a semi-logarithmic plot of emission intensity for the 670 nm spectrum as a function of distance from the surface, the mean velocity of the excited Ti atoms and ions in a normal direction parallel to the surface, or

  4. Theoretical investigations of the optical and EPR spectra for trivalent cerium and ytterbium ions in orthorhombic YF3 crystal

    Science.gov (United States)

    Liu, Hong-Gang; Zheng, Wen-Chen

    2016-09-01

    The optical spectra and electron paramagnetic resonance (EPR) parameters (g factors and hyperfine structure constants A) for trivalent cerium and ytterbium ions in YF3 crystal with orthorhombic structure are investigated together by the complete diagonalization (of energy matrix) method (CDM). The obtained results are in reasonable agreement with the experimental ones. More importantly, two magnetically nonequivalent centers in YF3 crystal observed in EPR experiments are confirmed and ascribed to their specific positions in a unit cell by our calculations based on superposition model (SPM) analysis. Such identification of local sites with different magnetic properties would help us to understand not only the EPR spectra and magnetic susceptibility of other lanthanide ions doped in crystals with the same structure as YF3 but also the energy transfer scheme between two lanthanide ions occupying such two sites. All results are discussed carefully.

  5. Methods and apparatus for cleaning objects in a chamber of an optical instrument by generating reactive ions using photon radiation

    Energy Technology Data Exchange (ETDEWEB)

    Klebanoff, Leonard E.; Delgado, Gildardo R.; Hollenshead, Jeromy T.; Umstadter, Karl R.; Starodub, Elena; Zhuang, Guorong V.

    2015-10-13

    An optical instrument, including a chamber, an object exposed to an interior of the chamber, a source of low-pressure gas, the gas comprising at least one of low-pressure molecular hydrogen gas, low-pressure molecular oxygen and a low-pressure noble gas, the source of low pressure gas being fluidly coupled to the chamber, a low voltage source electrically coupled between the object and a remaining portion of the instrument that is exposed to the interior of the chamber so as to maintain the object at a low voltage relative to the remaining portion, and an EUV/VUV light source adapted to direct EUV/VUV light through the low pressure gas in the chamber onto the object. In such a system, when the EUV/VUV light source is activated ions of the low-pressure gas are formed and directed to the object. The ions may be ions of Hydrogen, Oxygen or a noble gas.

  6. Optical absorption and small-polaron hopping in oxygen deficient and lithium-ion-intercalated amorphous titanium oxide films

    Science.gov (United States)

    Triana, C. A.; Granqvist, C. G.; Niklasson, G. A.

    2016-01-01

    Optical absorption in oxygen-deficient and Li+-ion inserted titanium oxide films was studied in the framework of small-polaron hopping. Non-stoichiometric TiOy films with 1.68 ≤ y ≤ 2.00 were deposited by reactive DC magnetron sputtering and were subjected to electrochemical intercalation of Li+-ions and charge-balancing electrons to obtain LixTiOy films with 0.12 ≤ x ≤ 0.34. Dispersion analysis was applied to calculate the complex dielectric function ɛ(ℏω) ≡ ɛ1(ℏω) + i ɛ2(ℏω) from numerical inversion of optical transmittance and reflectance spectra; a superposition of Tauc-Lorentz and Lorentz oscillator models was used for this purpose. Data on ɛ2(ℏω) were employed to calculate the optical conductivity and fit this property to a small-polaron model for disordered systems with strong electron-phonon interaction and involving transitions near the Fermi level. The introduction of oxygen vacancies and/or Li+ insertion yielded band gap widening by ˜0.20-0.35 eV, and both processes induced similar low-energy optical absorption. The small-polaron-based analysis indicated increases in the Fermi level by ˜0.15-0.3 eV for sub-stoichiometric and/or Li+-inserted films. This suggests the existence of polaronic Ti3+ states in the lower part of the conduction band arising from transfer of electrons from oxygen vacancies and/or inserted Li+ species. The present article is a sequel to an earlier paper on oxygen-deficient and/or Li+-inserted amorphous WOy thin films and forms part of a comprehensive investigation of optical absorption in amorphous transition metal oxides with different valence states of the metallic ions.

  7. FORMATION OF LUMINESCENT OPTICAL WAVEGUIDES IN SILICATE GLASS MATRIX BY THE ION-EXCHANGE TECHNIQUE

    Directory of Open Access Journals (Sweden)

    I. A. Dyomichev

    2015-01-01

    Full Text Available We present spectra of the alkali-silicate glasses with copper ions in near-surface area, introduced by ion exchange of different temperature and duration. It is shown that the reduction of Cu2+ in the near-surface area causes existence of Cu+ and neutral atoms in glass after the ion-exchange in divalent salt. The ion-exchange itself involves only Cu+ and Na+ ions. The formation of subnanometer clusters Cun is due to neutral copper atoms staying in near-surface zone. We have shown that the waveguide layer in near-surface area, made by ion-exchange, has а visible luminescence with the excitation by UVradiation. At the same time, the contribution to luminescence is made by Cu+ ions, molecular clusters Cun and by dimers Cu+ - Cu+ . During the high-temperature ion-exchange at 600 °С the formation and destruction equilibrium shift of molecular clusters Cun can be seen. An hour ion-exchange leads to molecular clusters Cun destruction, while at time periods less than 30 min and around 18 hours it leads to the formation of Cun. The sample turns green after 18,5 hours ion-exchange showing formation of a considerable amount of divalent copper ions Cu2+ therein.

  8. Optical stability of 3d transition metal ions doped-cadmium borate glasses towards γ-rays interaction

    Science.gov (United States)

    Marzouk, M.; ElBatal, H.; Eisa, W.

    2016-07-01

    This work reports the preparation of glasses of binary cadmium borate with the basic composition (mol% 45 CdO 55 B2O3) and samples of the same composition containing 0.2 wt% dopants of 3d transition metal (TM) oxides (TiO2 → CuO). The glasses have been investigated by combined optical and Fourier Transform infrared spectroscopic measurements before and after being subjected to gamma irradiation with a dose of 8 Mrad (8 × 104 Gy). Optical absorption of the undoped glass before irradiation reveals strong charge transfer UV absorption which is related to the presence of unavoidable contaminated trace iron impurities (mainly Fe3+) within the raw materials used for the preparation of the base cadmium borate glass. The optical spectra of the 3d TM ions exhibit characteristic bands which are related the stable oxidation state of the 3d TM ions within the host glass. Gamma irradiation produces some limited variations in the optical spectra due to the stability of the host glass containing high percent 45 mol% of heavy metal oxide (CdO) which causes some shielding effects towards irradiation. From the absorption edge data, the values of the optical band gap Eopt and Urbach energy (∆E) have been calculated. The values of the optical energy gap are found to be dependent on the glass composition. Infrared absorption spectral measurements reveal characteristic absorption bands due to both triangular and tetrahedral borate groups with the BO3 units vibrations more intense than BO4 units due to the known limit value for the change of BO3 to BO4 groups. The introduction of 3d TM ions with the doping level (0.2 wt%) causes no changes in the number or position of the IR bands because of the presence of TM ions in modifying sites in the glass network. It is observed that gamma irradiation causes some limited changes in the FT-IR spectral bands due to the stability of the host heavy cadmium borate glass.

  9. Experimental and numerical optical characterization of plasmonic copper nanoparticles embedded in ZnO fabricated by ion implantation and annealing

    Energy Technology Data Exchange (ETDEWEB)

    Le, Khai Q. [Faculty of Science and Technology, Hoa Sen University, Ho Chi Minh City (Viet Nam); Department of Physics, Faculty of Science, Jazan University, P.O. Box 114, 45142 Jazan (Saudi Arabia); Nguyen, Hieu P.T. [Department of Electrical and Computer Engineering, New Jersey Institute of Technology, NJ 07102 (United States); Ngo, Quang Minh [Institute of Material Sciences, Vietnam Academy of Science and Technology, 18 Hoang Quoc Viet Road, Cau Giay, Hanoi (Viet Nam); Canimoglu, Adil [Nigde University, Faculty of Arts and Sciences, Physics Department, Nigde (Turkey); Can, Nurdogan, E-mail: cannurdogan@yahoo.com [Celal Bayar University, Faculty of Arts and Sciences, Department of Physics, Muradiye, Manisa (Turkey); Department of Physics, Faculty of Science, Jazan University, P.O. Box 114, 45142 Jazan (Saudi Arabia)

    2016-06-05

    Here we describe the successfully fabrication of metal nanoparticle crystals by implanting copper (Cu) ions into single zinc oxide (ZnO) crystals with ion energy of 400 keV at ion doses of 1 × 10{sup 16} to 1 × 10{sup 17} ions/cm{sup 2}. After implantation and post-annealing treatment, the Cu implanted ZnO produces a broad range of luminescence emissions, ranging from green to yellow. A green luminescence peak at 550 nm could be ascribed to the isolated Cu ions. The changes in luminescence emission bands between the initial implant and annealed suggest that the implants give rise to clustering Cu nanoparticles in the host matrix but that the annealing process dissociates these. Numerical modelling of the Cu nanoparticles was employed to simulate their optical properties including the extinction cross section, electron energy loss spectroscopy and cathodoluminescence. We demonstrate that the clustering of nanoparticles generates Fano resonances corresponding to the generation of multiple resonances, while the isolation of nanoparticles results in intensity amplification. - Highlights: • We present the fabrication of metal nanoparticle crystals by implanting Cu into ZnO. • The luminescence properties were studied at different annealing temperature. • Numerical modelling of the Cu nanoparticles was employed. • We demonstrate that the clustering of nanoparticles generates Fano resonances.

  10. Detection of heavy metal ions in contaminated water by surface plasmon resonance based optical fibre sensor using conducting polymer and chitosan.

    Science.gov (United States)

    Verma, Roli; Gupta, Banshi D

    2015-01-01

    Optical fibre surface plasmon resonance (SPR) based sensor for the detection of heavy metal ions in the drinking water is designed. Silver (Ag) metal and indium tin oxide (ITO) are used for the fabrication of the SPR probe which is further modified with the coating of pyrrole and chitosan composite. The sensor works on the wavelength interrogation technique and is capable of detecting trace amounts of Cd(2+), Pb(2+), and Hg(2+) heavy metal ions in contaminated water. Four types of sensing probes are fabricated and characterised for heavy metal ions out of these pyrrole/chitosan/ITO/Ag coated probe is found to be highly sensitive among all other probes. Further, the cadmium ions bind strongly to the sensing surface than other ions and due to this the sensor is highly sensitive for Cd(2+) ions. The sensor's performance is best for the low concentrations of heavy metal ions and its sensitivity decreases with the increasing concentration of heavy metal ions.

  11. Formation of a planar optical waveguide by mega-electron-volt He+ and P+ ions implanted in a BiB(3)O(6) crystal.

    Science.gov (United States)

    Chen, F; Hu, H; Wang, K M; Teng, B; Wang, J Y; Lu, Q M; Shen, D Y

    2001-12-15

    What is believed to be the first planar optical waveguide was formed in BiB(3)O(6) (BIBO) crystal by 2.8-MeV He(+)-ion implantation with a dose of 2x10(16)ions/cm (2) and 2.8-MeV P(+)-ion implantation with a dose of 1x10(14)ions/cm (2) at room temperature. We observed 21 darks modes for the He(+)-ion-implanted BIBO waveguides and four dark modes for the P(+)-ion-implanted waveguides. The refractive-index profile of the He(+)-implanted BIBO waveguide was analyzed. The data also suggest that the BIBO waveguides formed by MeV He(+)-ion and P(+)-ion implantation differ in their developing mechanisms.

  12. Universal nonmonotonic structure in the saturation curves of magneto-optical-trap-loaded Na+ ions stored in an ion-neutral hybrid trap: Prediction and observation

    Science.gov (United States)

    Blümel, R.; Wells, J. E.; Goodman, D. S.; Kwolek, J. M.; Smith, W. W.

    2015-12-01

    We predict that the maximal, steady-state ion capacity Ns(λ ) of radio-frequency (rf) traps, loaded at a rate of λ particles per rf cycle, shows universal, nonlinear, nonmonotonic behavior as a function of loading rate λ . The shape of Ns(λ ) , characterized by four dynamical regimes, is universal; i.e., it is predicted to manifest itself in all types of rf traps independent of the details of their construction and independent of particle species loaded. For λ ≪ 1 (region I), as expected, Ns(λ ) increases monotonically with λ . However, contrary to intuition, at intermediate λ ˜1 (region II), Ns(λ ) reaches a maximum, followed by a local minimum of Ns(λ ) (region III). For λ ≫1 (region IV), Ns(λ ) again rises monotonically. In region IV, numerical simulations, analytical calculations, and experiments show Ns(λ ) ˜λ2 /3 . We confirm our predictions both experimentally with magneto-optical-trap-loaded Na+ ions stored in a hybrid ion-neutral trap and numerically with the help of detailed ab initio molecular-dynamics simulations.

  13. Surface ion trap structures with excellent optical access for quantum information processing

    Science.gov (United States)

    Maunz, P.; Blain, M.; Benito, F.; Chou, C.; Clark, C.; Descour, M.; Ellis, R.; Haltli, R.; Heller, E.; Kemme, S.; Sterk, J.; Tabakov, B.; Tigges, C.; Stick, D.

    2013-05-01

    Microfabricated surface electrode ion traps are necessary for the advancement of trapped ion quantum information processing as it offers a scalable way for realizing complex trap structures capable of storing and controlling many ions. The most promising way of performing two-qubit quantum gates in a chain of trapped ions is to focus laser beams on individual ions of the chain to drive gates. However, in surface ion traps the close proximity of the ions to the surface and the size of the chips usually cannot accommodate the tightly focused laser beams necessary to address individual ions parallel to the chip surface. Here we present a surface electrode ion trap monolithically fabricated in standard silicon technology that implements a linear quadrupole trap on a bowtie shaped chip with a narrow section that is only 1.2 mm wide. Laser beams parallel to the surface can be focused down to a waist of 4 μm with enough separation from the trap chip to prevent light scattering. The trap structure incorporates two Y-junctions for reordering ions and is optimized for quantum information processing. This work was supported by the Intelligence Advanced Research Projects Activity (IARPA). Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the US Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

  14. The effect of 100 MeV oxygen ion on electrical and optical properties of nonlinear optical l-alanine sodium nitrate single crystals

    Energy Technology Data Exchange (ETDEWEB)

    Ahlam, M. A.; Prakash, A. P. Gnana [Department of Studies in Physics, University of Mysore, Mysore-570 006, Karnataka (India)

    2012-06-05

    Single crystals of nonlinear optical (NLO) L-alanine Sodium Nitrate (LASN) were grown by slow evaporation method. The grown crystals were irradiated by 100 MeV oxygen ions with the cumulative doses of 1Mrad, 6 Mrad and 10 Mrad. The dielectric properties, differential scanning calorimetry (DSC) and second harmonic generation (SHG) of the crystals were studied before and after irradiation. The dielectric constant was found to increase after irradiation. The DSC reveals that the melting point remains unaffected due to irradiation. The SHG efficiency of LASN was found to decrease with increase in radiation dose.

  15. The effect of 100 MeV oxygen ion on electrical and optical properties of nonlinear optical l-alanine sodium nitrate single crystals

    Science.gov (United States)

    Ahlam, M. A.; Prakash, A. P. Gnana

    2012-06-01

    Single crystals of nonlinear optical (NLO) L-alanine Sodium Nitrate (LASN) were grown by slow evaporation method. The grown crystals were irradiated by 100 MeV oxygen ions with the cumulative doses of 1Mrad, 6 Mrad and 10 Mrad. The dielectric properties, differential scanning calorimetry (DSC) and second harmonic generation (SHG) of the crystals were studied before and after irradiation. The dielectric constant was found to increase after irradiation. The DSC reveals that the melting point remains unaffected due to irradiation. The SHG efficiency of LASN was found to decrease with increase in radiation dose.

  16. Optical properties of plasma ion-assisted deposition silicon coatings: application to the manufacture of blocking filters for the near-infrared region.

    Science.gov (United States)

    Bruynooghe, Stephane

    2008-05-01

    I report on the preparation and characterization of optical constants of silicon coatings deposited by an electron beam gun with plasma ion-assisted deposition. With the fabrication of long-wave-pass filters the reliability of the optical constants is assured.

  17. Imprint Molding of a Microfluidic Optical Cell on Thermoplastics with Reduced Surface Roughness for the Detection of Copper Ions.

    Science.gov (United States)

    Wu, Jing; Lee, Nae Yoon

    2016-01-01

    Here, we introduce a simple and facile technique for fabricating microfluidic optical cells by utilizing a micropatterned polymer mold, followed by imprinting on thermoplastic substrates. This process has reduced the surface roughness of the microchannel, making it suitable for microscale optical measurements. The micropatterned polymer mold was fabricated by first micromilling on a poly(methylmethacrylate) (PMMA) substrate, and then transferring the micropattern onto an ultraviolet (UV)-curable optical adhesive. After an anti-adhesion treatment of the polymer mold fabricated using the UV-curable optical adhesive, the polymer mold was used repeatedly for imprinting onto various thermoplastics, such as PMMA, polycarbonate (PC), and poly(ethyleneterephthalate) (PET). The roughness values for the PMMA, PC, and PET microchannels were approximately 11.3, 20.3, and 14.2 nm, respectively, as compared to those obtained by micromilling alone, which were 15.9, 76.8, and 207.5 nm, respectively. Using the imprint-molded thermoplastic optical cell, rhodamine B and copper ions were successfully quantified. The reduced roughness of the microchannel surface resulted in improved sensitivity and reduced noise, paving the way for integration of the detection module so as to realize totally integrated microdevices.

  18. Highly charged ions as a basis of optical atomic clockwork of exceptional accuracy.

    Science.gov (United States)

    Derevianko, Andrei; Dzuba, V A; Flambaum, V V

    2012-11-02

    We propose a novel class of atomic clocks based on highly charged ions. We consider highly forbidden laser-accessible transitions within the 4f(12) ground-state configurations of highly charged ions. Our evaluation of systematic effects demonstrates that these transitions may be used for building exceptionally accurate atomic clocks which may compete in accuracy with recently proposed nuclear clocks.

  19. Modification of optical and electrical properties of zinc oxide-coated porous silicon nanostructures induced by swift heavy ion.

    Science.gov (United States)

    Kumar, Yogesh; Herrera-Zaldivar, Manuel; Olive-Méndez, Sion Federico; Singh, Fouran; Mathew, Xavier; Agarwal, Vivechana

    2012-07-02

    Morphological and optical characteristics of radio frequency-sputtered zinc aluminum oxide over porous silicon (PS) substrates were studied before and after irradiating composite films with 130 MeV of nickel ions at different fluences varying from 1 × 1012 to 3 × 1013 ions/cm2. The effect of irradiation on the composite structure was investigated by scanning electron microscopy, X-ray diffraction (XRD), photoluminescence (PL), and cathodoluminescence spectroscopy. Current-voltage characteristics of ZnO-PS heterojunctions were also measured. As compared to the granular crystallites of zinc oxide layer, Al-doped zinc oxide (ZnO) layer showed a flaky structure. The PL spectrum of the pristine composite structure consists of the emission from the ZnO layer as well as the near-infrared emission from the PS substrate. Due to an increase in the number of deep-level defects, possibly oxygen vacancies after swift ion irradiation, PS-Al-doped ZnO nanocomposites formed with high-porosity PS are shown to demonstrate a broadening in the PL emission band, leading to the white light emission. The broadening effect is found to increase with an increase in the ion fluence and porosity. XRD study revealed the relative resistance of the film against the irradiation, i.e., the irradiation of the structure failed to completely amorphize the structure, suggesting its possible application in optoelectronics and sensing applications under harsh radiation conditions.

  20. Detailed subsurface damage measurement and efficient damage-free fabrication of fused silica optics assisted by ion beam sputtering.

    Science.gov (United States)

    Liao, Wenlin; Dai, Yifan; Liu, Zongzheng; Xie, Xuhui; Nie, Xuqing; Xu, Mingjin

    2016-02-22

    Formation of subsurface damage has an inseparable relationship with microscopic material behaviors. In this work, our research results indicate that the formation process of subsurface damage often accompanies with the local densification effect of fused silica material, which seriously influences microscopic material properties. Interestingly, we find ion beam sputtering (IBS) is very sensitive to the local densification, and this microscopic phenomenon makes IBS as a promising technique for the detection of nanoscale subsurface damages. Additionally, to control the densification effect and subsurface damage during the fabrication of high-performance optical components, a combined polishing technology integrating chemical-mechanical polishing (CMP) and ion beam figuring (IBF) is proposed. With this combined technology, fused silica without subsurface damage is obtained through the final experimental investigation, which demonstrates the feasibility of our proposed method.

  1. Magnetic and optical properties of electrospun hollow nanofibers of SnO2 doped with Ce-ion

    Science.gov (United States)

    Mohanapriya, P.; Pradeepkumar, R.; Victor Jaya, N.; Natarajan, T. S.

    2014-07-01

    Cerium doped SnO2 hollow nanofibers were synthesized by electrospinning. High resolution scanning electron microscope (HRSEM) and transmission electron microscopy (TEM) analysis showed hollow nanofibers with diameters around ˜200 nm. The optimized substitution of Ce ion into SnO2 lattices happened above 6 mol. % doping as confirmed by Powder X-ray diffraction (XRD) studies. Optical band gap was decreased by the doping confirming the direct energy transfer between f-electrons of rare earth ion and the SnO2 conduction or valence band. The compound also exhibited room temperature ferromagnetism with the saturation magnetization of 19 × 10-5 emu/g at 6 mol. %. This study demonstrates the Ce doped SnO2 hollow nanofibers for applications in magneto-optoelectronic devices.

  2. Structural and optical properties of Cd{sup 2+} ion on the growth of sulphamic acid single crystals

    Energy Technology Data Exchange (ETDEWEB)

    Rajyalakshmi, S.; Samatha, K. [Department of Physics, Andhra University, Visakhapatnam-530003 (India); Rao, Valluru Srinivasa; Reddy, P. V. S. S. S. N.; Rao, K. Ramachandra, E-mail: drkrcr@gmail.com [Crystal Growth & Nano Science Research Center, Department of Physics, Govt. College (A), Rajahmundry-533 105 (India); Krishna, V. Y. Rama [Department of Engg. Physics, Andhra University, Visakhapatnam-530003 (India)

    2016-05-06

    Transparent single crystals of Cadmium doped Sulphamic acid (SA) was grown by Conventional slow evaporation solution technique (SEST) which had the size of 13 × 8 × 7 mm{sup 3}. The grown single crystals have been characterized using single crystal X-ray diffraction UV-visible Spectral studies and Second harmonic generation (SHG) efficiency and the results were discussed. The lattice parameters of the grown Cd{sup 2+} ion doped SA crystal are confirmed by single crystal X-ray diffraction and belong to orthorhombic system. Optical transmittance of the crystal was recorded using UV-vis NIR spectrophotometer with its lower cut off wavelength around 259nm. SHG measurements indicate that the SHG efficiency of the grown Cd{sup 2+} ion doped SA crystal at a fundamental wavelength of 1064 nm is approximately equal to KDP.

  3. The structural,magnetic,and optical properties of ZnO (0001) wafers implanted with Co ions

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The ion implantation technique was employed to study the structural,magnetic,and optical properties of Co-doped crystalline ZnO.The photoluminescence measurements indicated that the center of green emission of implanted samples shifts gradually from 510 nm to 531 nm with an increase of Co concentrations.All implanted samples are ferromagnetic at room temperature with a saturation magnetization from 6.89×10-5 to 2.31×10-4 emu.The possible mechanisms on the observed ferromagnetism were discussed.

  4. Luminescence and optical absorption studies of submicro-dimensional cerium ortho- and metaphosphates doped with Eu{sup 3+} ions

    Energy Technology Data Exchange (ETDEWEB)

    Matraszek, A. [Department of Inorganic Chemistry, Faculty of Engineering and Economics, Wroclaw University of Economics, 118/120 Komandorska str., 53-345 Wroclaw (Poland); Macalik, L. [Institute of Low Temperature and Structure Research, Polish Academy of Sciences, P.O. Box 1410, 50-950 Wroclaw (Poland); Szczygiel, I. [Department of Inorganic Chemistry, Faculty of Engineering and Economics, Wroclaw University of Economics, 118/120 Komandorska str., 53-345 Wroclaw (Poland); Godlewska, P. [Department of Bioorganic Chemistry, Faculty of Engineering and Economics, Wroclaw University of Economics, 118/120 Komandorska str., 53-345 Wroclaw (Poland); Solarz, P. [Institute of Low Temperature and Structure Research, Polish Academy of Sciences, P.O. Box 1410, 50-950 Wroclaw (Poland); Hanuza, J. [Institute of Low Temperature and Structure Research, Polish Academy of Sciences, P.O. Box 1410, 50-950 Wroclaw (Poland)], E-mail: j.hanuza@int.pan.wroc.pl

    2008-02-28

    Pechini method has been applied for synthesis of the phosphates in the submicro-state. Dimensions of the obtained grains by this method fall into the 100-1000 nm range. The following samples have been synthesised: stoichiometric orthophosphate Na{sub 3}Ce(PO{sub 4}){sub 2} and metaphosphate NaCe(PO{sub 3}){sub 4} both doped with 2 and 5% of Eu{sup 3+}. Optical absorption and emission studies have been performed to characterise the properties and structure of the compounds studied. The electronic characteristics of the Ce{sup 3+} and Eu{sup 3+} ions in these materials have been discussed.

  5. Lattice damage assessment and optical waveguide properties in LaAlO3 single crystal irradiated with swift Si ions

    Science.gov (United States)

    Liu, Y.; Crespillo, M. L.; Huang, Q.; Wang, T. J.; Liu, P.; Wang, X. L.

    2017-02-01

    As one of the representative ABO3 perovskite-structured oxides, lanthanum aluminate (LaAlO3) crystal has emerged as one of the most valuable functional-materials, and has attracted plenty of fundamental research and promising applications in recent years. Electronic, magnetic, optical and other properties of LaAlO3 strongly depend on its crystal structure, which could be strongly modified owing to the nuclear or electronic energy loss deposited in an ion irradiation environment and, therefore, significantly affecting the performance of LaAlO3-based devices. In this work, utilizing swift (tens of MeV) Si-ion irradiation, the damage behavior of LaAlO3 crystal induced by nuclear or electronic energy loss has been studied in detail utilizing complementary characterization techniques. Differing from other perovskite-structured crystals in which the electronic energy loss could lead to the formation of an amorphous region based on the thermal spike mechanism, in this case, intense electronic energy loss in LaAlO3 will not induce any obvious structural damage. The effects of ion irradiation on the mechanical properties, including hardness increase and elastic modulus decrease, have been confirmed. On the other hand, considering the potential applications of LaAlO3 in the field of integrated optoelectronics, the optical-waveguide properties of the irradiation region have been studied. The significant correspondence (symmetrical inversion) between the iWKB-reconstructed refractive-index profile and SRIM-simulated dpa profile further proves the effects (irradiation-damage production and refractive-index decrease) of nuclear energy loss during the swift-ion penetration process in LaAlO3 crystal. In the case of the rather-thick damage layer produced by swift-ion irradiation, obtaining a damage profile will be constrained owing to the analysis-depth limitation of the characterization techniques (RBS/channeling), and our analysis process (optical guided-mode measurement and

  6. Effect of annealing on the optical properties of the ion beam sputtered NiO thin film

    Science.gov (United States)

    Chouhan, Romita; Baraskar, Priyanka; Dar, Tanveer A.; Agrawal, Arpana; Gupta, Mukul; Sen, Pranay K.; Sen, Pratima.

    2017-05-01

    Effect of annealing on optical characteristics of Nickel oxide thin films deposited by ion beam sputtering technique from a Ni target in a mixture of oxygen and argon gas on to a glass substrate has been studied. The deposited films were characterized in as deposited state(S1) and after annealing(S2) at temp of 523 K. Crystalline properties of films were investigated using X-ray diffraction technique from which we found that both S1 and S2 shows the polycrystalline nature with preferential growth along (111) plane. The transmittance of the S2 films was decreased. The surface morphology of the film was studied using atomic force microscopy (AFM). The nonlinear optical properties of the films were obtained using z-scan technique which reveals that the nonlinear absorption coefficient of S2 films is larger than that of S1 samples. Improved nonlinearity suggests the utility of the grown films for optoelectronic device application.

  7. Super-resolution nanofabrication with metal-ion doped hybrid material through an optical dual-beam approach

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Yaoyu; Li, Xiangping; Gu, Min, E-mail: mgu@swin.edu.au [Centre for Micro-Photonics, Faculty of Science, Engineering and Technology, Swinburne University of Technology, P.O. Box 218, Hawthorn, Victoria 3122 (Australia)

    2014-12-29

    We apply an optical dual-beam approach to a metal-ion doped hybrid material to achieve nanofeatures beyond the optical diffraction limit. By spatially inhibiting the photoreduction and the photopolymerization, we realize a nano-line, consisting of polymer matrix and in-situ generated gold nanoparticles, with a lateral size of sub 100 nm, corresponding to a factor of 7 improvement compared to the diffraction limit. With the existence of gold nanoparticles, a plasmon enhanced super-resolution fabrication mechanism in the hybrid material is observed, which benefits in a further reduction in size of the fabricated feature. The demonstrated nanofeature in hybrid materials paves the way for realizing functional nanostructures.

  8. Abnormal Dielectric Response in an Optical Range Based on Electronic Transition in Rare-Earth-Ion-Doped Crystals

    Institute of Scientific and Technical Information of China (English)

    FU Xiao-Jian; XU Yuan-Da; ZHOU Ji

    2012-01-01

    A new scheme to realize an abnormal dielectric response at optical wavelength is developed on the basis of twolevel electronic transition of rare-earth ion doped crystals.Based on the semi-classical theory and the Judd-Ofelt theory,the electric dipole transition under a weak field is analyzed,and a general expression for the frequencydependent dielectric constant is obtained.As an example,the permittivity of (Erx Y1-x)3Al5O12 is calculated numerically in consideration of the transition between 4I15/2and 4F9/2.An optimized dielectric property with a negative real part and low absorption is achieved.This proposes a new mechanism for building extraordinary electromagnetic media at optical frequencies by using a quantum process.%A new scheme to realize an abnormal dielectric response at optical wavelength is developed on the basis of two-level electronic transition of rare-earth ion doped crystals. Based on the semi-classical theory and the Judd-Ofelt theory, the electric dipole transition under a weak Reid is analyzed, and a general expression for the frequency-dependent dielectric constant is obtained. As an example, the permittivity of (ErxY1-x)3A15O12 is calculated numerically in consideration of the transition between 4I15/2 and 4F9/2. An optimized dielectric property with a negative real part and low absorption is achieved. This proposes a new mechanism for building extraordinary electromagnetic media at optical frequencies by using a quantum process.

  9. Optical nonlinearity and-ultrafast dynamics of ion exchanged silver nanoparticles embedded in soda-lime silicate glass

    Institute of Scientific and Technical Information of China (English)

    YANG XiuChun; LI ZhiHui; LI WeiJie; XU JingXian; DONG ZhiWei; QIAN ShiXiong

    2008-01-01

    Ag nanoparticles embedded in soda-lime silicate glass were fabricated by ion-exchange and subsequently annealing method. Z-scan technique, femtosecond time-resolved optical Kerr effect (OKE) technique and femtosecond pump-probe experiment were used to investigate the effects of laser wavelength and laser pulse duration as well as annealing temperature on the third-order optical nonlinearity and ultrafast dynamics of the composites. It was found that the third-order susceptibility of Ag nanoparticles composite glass measured by 400 nm pulse source is larger than that measured by 800 nm pulse source due to an enhancement effect of local field near surface plasmon resonance of Ag nanoparticles in silicate glass. The third-order optical nonlinearity measured by ns laser source is about two orders of magnitude larger than that measured from fs pulse. The annealing temperature has an important effect on the third-order optical nonlinearity and ultrafast dynamics of the composites. Third-order nonlinear susceptibility upto 10-10 esu and fast relaxation process up to 0.2 ps have been obtained in Ag nanoparticles doped glass,

  10. Electrochemical, optical and metal ion sensing properties of dithizone derivatised electrodes

    CERN Document Server

    Mirkhalaf, F

    1998-01-01

    studied. Possible applications of these modified electrodes with potential control in metal ion detection are described. The electrochemical and SPR responses for the metal ion sensing by the monolayer films were compared with those of polymer films containing the same ligand. Derivatisation of electrode surfaces with ultra-thin films of organic molecules has been extensively studied for many applications in recent years. The present study is based on a new approach in the preparation and use of these electrodes for metal ion sensing. Modification of electrode surfaces with a ligand specific to heavy metal ions has been described. A new derivative of dithizone (DDz) and its secondary metal complexes have been synthesised and attached onto indium tin oxide (ITO) and gold electrodes. This was achieved by covalent bonding between carboxyl groups in DDz and terminal amine groups of molecules self-assembled on the electrode surfaces. These monolayer films were characterised by cyclic voltammetry, by in situ and ex...

  11. Study of negative hydrogen ion beam optics using the 3D3V PIC model

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, K., E-mail: kmiyamot@naruto-u.ac.jp [Naruto University of Education, 748 Nakashima, Takashima, Naruto-cho, Naruto-shi, Tokushima, 772-8502 (Japan); Nishioka, S.; Goto, I.; Hatayama, A. [Faculty of Science and Technology, Keio University, 3-14-1, Hiyoshi, Kohoku-ku, Yokohama, 223-8522 (Japan); Hanada, M.; Kojima, A. [Japan Atomic Energy Agency, 801-1,Mukoyama, Naka, 319-0913 (Japan)

    2015-04-08

    The mechanism of negative ion extraction under real conditions with the complex magnetic field is studied by using the 3D PIC simulation code. The extraction region of the negative ion source for the negative ion based neutral beam injection system in fusion reactors is modelled. It is shown that the E x B drift of electrons is caused by the magnetic filter and the electron suppression magnetic field, and the resultant asymmetry of the plasma meniscus. Furthermore, it is indicated that that the asymmetry of the plasma meniscus results in the asymmetry of negative ion beam profile including the beam halo. It could be demonstrated theoretically that the E x B drift is not significantly weakened by the elastic collisions of the electrons with neutral particles.

  12. Determination of optical damage cross-sections and volumes surrounding ion bombardment tracks in GaAs using coherent acoustic phonon spectroscopy

    Science.gov (United States)

    Steigerwald, A.; Hmelo, A. B.; Varga, K.; Feldman, L. C.; Tolk, N.

    2012-07-01

    We report the results of coherent acoustic phonon spectroscopy analysis of band-edge optical modification of GaAs irradiated with 400 keV Ne++ for doses between 1011-1013 cm-2. We relate this optical modification to the structural damage density as predicted by simulation and verified by ion channeling analysis. Crystal damage is observed to cause optical modification that reduces the amplitude of the optoacoustic signal. The depth-dependent nature of the optoacoustic measurement allows us to determine optical damage cross-sections along the ion track, which are found to vary as a function of position along the track. Unexpectedly, we find that this optical modification is primarily dependent on the structural damage density and insensitive to the specific defect configuration along the ion track, suggesting that a simple model of defect density along the track is sufficient to characterize the observed optical changes. The extent of optical modification is strongly probe frequency-dependent as the frequency is detuned from the GaAs band edge. As determined from the experimental measurements, the spatial extent of optical modification exceeds the spatial extent of the structural disorder by an order of magnitude.

  13. Zinc finger peptide based optic sensor for detection of zinc ions.

    Science.gov (United States)

    Verma, Neelam; Kaur, Gagandeep

    2016-12-15

    In the present work, polyacrylamide gel has been used as a matrix for the immobilization of zinc finger peptide and fluorescent dye acrydine orange on the micro well plate to fabricate the fluorescence based biosensor for the detection of zinc ions in milk samples. The fluorescent dye moves in the hydrophobic groove formed after folding of the peptide in the presence of zinc ions. Under optimized conditions, linear range was observed between 0.001µg/l to 10µg/l of Zinc ions, with a lowest detection limit of 0.001µg/l and response time of 5min. Presented biosensor has shown 20% decrease in fluorescent intensity values after 5 regenerations and stable for more than one month, stored at 4°C. Interference study with other metal ions like lead, cadmium and copper showed a negligible change in fluorescence intensity in comparison to zinc ions. Developed bio sensing system was found to be novel, quick, reliable, miniaturized, stable, reproducible and repeatable and specific for zinc ion, which has been applied to various milk samples.

  14. Measurement of axial neutral density profiles in a microwave discharge ion thruster by laser absorption spectroscopy with optical fiber probes.

    Science.gov (United States)

    Tsukizaki, Ryudo; Koizumi, Hiroyuki; Nishiyama, Kazutaka; Kuninaka, Hitoshi

    2011-12-01

    In order to reveal the physical processes taking place within the "μ10" microwave discharge ion thruster, internal plasma diagnosis is indispensable. However, the ability of metallic probes to access microwave plasmas biased at a high voltage is limited from the standpoints of the disturbance created in the electric field and electrical isolation. In this study, the axial density profiles of excited neutral xenon were successfully measured under ion beam acceleration by using a novel laser absorption spectroscopy system. The target of the measurement was metastable Xe I 5p(5)((2)P(0) (3/2))6s[3/2](0) (2) which absorbed a wavelength of 823.16 nm. Signals from laser absorption spectroscopy that swept a single-mode optical fiber probe along the line of sight were differentiated and converted into axial number densities of the metastable neutral particles in the plasma source. These measurements revealed a 10(18) m(-3) order of metastable neutral particles situated in the waveguide, which caused two different modes during the operation of the μ10 thruster. This paper reports a novel spectroscopic measurement system with axial resolution for microwave plasma sources utilizing optical fiber probes.

  15. Microstructure characterization and optical properties of sapphire after helium ion implantation

    Energy Technology Data Exchange (ETDEWEB)

    Zhong, Mian; Yang, Liang [School of Physical Electronics, University of Electronic Science and Technology of China, Chengdu 610054 (China); Shen, Huahai [School of Physical Electronics, University of Electronic Science and Technology of China, Chengdu 610054 (China); Department of Materials Science and Engineering, University of Michigan, Ann Arbor, MI 48109 (United States); Liu, Wei [School of Physical Electronics, University of Electronic Science and Technology of China, Chengdu 610054 (China); Xiang, Xia, E-mail: xiaxiang@uestc.edu.cn [School of Physical Electronics, University of Electronic Science and Technology of China, Chengdu 610054 (China); Zheng, Wanguo, E-mail: wgzheng_caep@sina.com [Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang 621900 (China); Guo, Decheng [School of Physical Electronics, University of Electronic Science and Technology of China, Chengdu 610054 (China); Huang, Jin [Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang 621900 (China); Sun, Kai [Department of Materials Science and Engineering, University of Michigan, Ann Arbor, MI 48109 (United States); Yuan, Xiaodong, E-mail: yxd66my@163.com [Research Center of Laser Fusion, China Academy of Engineering Physics, Mianyang 621900 (China)

    2015-06-15

    The (0 0 0 1) sapphire samples are irradiated with 60 keV helium ions at the fluences of 5 × 10{sup 16}, 1 × 10{sup 17}and 5 × 10{sup 17} ions/cm{sup 2} at room temperature. After implantation, two broad absorption bands at 320–460 and 480–700 nm are observed and their intensities increase with the increasing ion fluence. The grazing incidence X-ray diffraction results indicate that the {0 0 0 1} diffraction peaks of sapphire decrease and broaden due to the disorientation of the generated crystallites after ion irradiation. The microstructure evolution is examined by the scanning and transmission electron microscopes. The surface becomes rough because of the aggregation of helium bubbles and migration towards the surface. There is a lattice expansion up to ∼4.5% in the implanted area and the lattice distortion measured from dispersion of (1 1 0) diffraction is ∼4.6°. Such strain of crystal lattice is rather large and leads to contrast fluctuation at scale of 1–2 nm (the bubble size). The laser induced damage threshold (LIDT) is investigated to understand the effect of helium ion beam irradiation on the laser damage resistance of sapphire components and the results show that the LIDT decreases from 5.4 to 2.5 J/cm{sup 2} due to the absorptive color centers, helium bubbles and defects induced by helium ion implantation. The laser damage morphologies of samples before and after ion implantation are also presented.

  16. Investigation of structural and optical properties of 100 MeV F7+ ion irradiated Ga10Se90-xAlx thin films

    Science.gov (United States)

    Ahmad, Shabir; Asokan, K.; Zulfequar, M.

    2015-04-01

    Present work focuses on the effect of swift heavy ion (SHI) irradiation of 100 MeV F7+ ions by varying the fluencies in the range of 1 × 1012 to 1 × 1013 ions/cm2 on the morphological, structural and optical properties of polycrystalline thin films of Ga10Se90-xAlx (x = 0, 5). Thin films of ~300 nm thickness were deposited on cleaned Al2O3 substrates by thermal evaporation technique. X-ray diffraction pattern of investigated thin films shows the crystallite growth occurs in hexagonal phase structure for Ga10Se90 and tetragonal phase structure for Ga10Se85Al5. The further structural analysis carried out by Raman spectroscopy and scanning electron microscopy verifies the defects or disorder of the investigated material increases after SHI irradiation. The optical parameters absorption coefficient (α), extinction coefficient (K), optical band gap (Eg) and Urbach's energy (EU) are determined from optical absorption spectra data measured from spectrophotometry in the wavelength range 200-1100 nm. It was found that the values of absorption coefficient and extinction coefficient increase while the value of optical band gap decreases with the increase in ion fluence. This post irradiation change in the optical parameters was interpreted in terms of bond distribution model.

  17. Ion gyro-harmonic structuring in the stimulated radiation spectrum and optical emissions during electron gyro-harmonic heating

    Science.gov (United States)

    Mahmoudian, A.; Scales, W. A.; Bernhardt, P. A.; Samimi, A.; Kendall, E.; Ruohoniemi, J. M.; Isham, B.; Vega-Cancel, O.; Bordikar, M.

    2013-03-01

    Stimulated electromagnetic emissions (SEEs) are secondary radiation produced during active space experiments in which the ionosphere is actively heated with high power high frequency (HF) ground-based radio transmitters. Recently, there has been significant interest in ion gyro-harmonic structuring the SEE spectrum due to the potential for new diagnostic information available such as electron acceleration and creation of artificial ionization layers. These relatively recently discovered gyro-harmonic spectral features have almost exclusively been studied when the transmitting frequency is near the second electron gyro-harmonic frequency. The first extensive systematic experimental investigations of the possibility of these spectral features for third electron gyro-harmonic heating are provided here. Discrete spectral features shifted from the transmit frequency ordered by harmonics of the ion gyro-frequency were observed for third electron gyro-harmonic heating for the first time at a recent campaign at the High Frequency Active Auroral Research Program (HAARP) facility. These features were also closely correlated with a broader band feature at a larger frequency shift from the transmit frequency known as the downshifted peak (DP). The power threshold of these spectral features was measured, as well as their behavior with heater beam angle, and proximity of the transmit frequency to the third electron gyro-harmonic frequency. Comparisons were also made with similar spectral features observed during second electron gyro-harmonic heating during the same campaign. A theoretical model is provided that interprets these spectral features as resulting from parametric decay instabilities in which the pump field ultimately decays into high frequency upper hybrid/electron Bernstein and low frequency neutralized ion Bernstein IB and/or obliquely propagating ion acoustic waves at the upper hybrid interaction altitude. Coordinated optical and SEE observations were carried out

  18. Durable Silver Mirror Coating Via Ion Assisted, Electron Beam Evaporation For Large Aperture Optics Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Highly reflective optical coatings with low scatter properties are needed to image very faint objects such as extra-solar planets. Silver has the highest...

  19. Effect of Pd ion doping in the band gap of SnO{sub 2} nanoparticles: structural and optical studies

    Energy Technology Data Exchange (ETDEWEB)

    Nandan, Brajesh; Venugopal, B. [Pondicherry University, Centre for Nanoscience and Technology (India); Amirthapandian, S.; Panigrahi, B. K. [Indira Gandhi Centre for Atomic Research, Ion Beam and Computer Simulation Section, Materials Science Group (India); Thangadurai, P., E-mail: thangadurai.p@gmail.com [Pondicherry University, Centre for Nanoscience and Technology (India)

    2013-10-15

    Pd ion doping has influenced the band gap of SnO{sub 2} nanoparticles. Undoped and Pd ion-doped SnO{sub 2} nanoparticles were synthesized by chemical co-precipitation method. A tetragonal phase of SnO{sub 2} with a grain size range of 7-13 nm was obtained (studied by X-ray diffraction and transmission electron microscopy). A decreasing trend in the particle size with increasing doping concentration was observed. The presence of Pd in doped SnO{sub 2} was confirmed by chemical analysis carried out by energy-dispersive spectroscopy in the transmission electron microscope. Diffuse reflectance spectra showed a blue shift in absorption with increasing palladium concentration. Band gap of SnO{sub 2} nanoparticles was estimated from the diffuse reflectance spectra using Kubelka-Munk function and it was increasing with the increase of Pd ion concentration from 3.73 to 4.21 eV. The variation in band gap is attributed predominantly to the lattice strain and particle size. All the samples showed a broad photoluminescence emission centered at 375 nm when excited at 270 nm. A systematic study on the structural and optical properties of SnO{sub 2} nanoparticles is presented.

  20. EPR and optical absorption studies on Gd{sup 3+} ions in ammonium hydrogen malonate single crystals

    Energy Technology Data Exchange (ETDEWEB)

    Kripal, Ram, E-mail: ram_kripal2001@rediffmail.co [EPR Laboratory, Department of Physics, University of Allahabad, Allahabad 211002 (India); Mishra, Indrajeet, E-mail: indrajeet_mishra47@rediffmail.co [EPR Laboratory, Department of Physics, University of Allahabad, Allahabad 211002 (India); Department of Physics, D.D.U. Government P.G. College, Saidabad, Allahabad (India)

    2010-01-01

    X-Band electron paramagnetic resonance (EPR) studies of Gd{sup 3+} ions in ammonium hydrogen malonate single crystals have been done at room temperature. Detailed EPR analysis indicates the presence of four physically equivalent but magnetically inequivalent sites. The zero-field splitting parameters and g factor are determined. The Gd{sup 3+} ion is in {sup 8}S state; its levels are split by the action of the crystalline electric field of monoclinic symmetry. The optical absorption spectra of Gd{sup 3+} ions in single crystals of ammonium hydrogen malonate are also recorded at room temperature. The energy levels of the 4f{sup 7} configuration are calculated and compared with those observed experimentally. The values of E{sup 1}=5854+-11, E{sup 2}=31+-0.36, E{sup 3}=592+-3.3 and zeta{sub 4f}=1595+-25 cm{sup -1} are found to give the best over-all agreement between experimentally observed and calculated levels.

  1. Focused ion beam post-processing of optical fiber Fabry-Perot cavities for sensing applications.

    Science.gov (United States)

    André, Ricardo M; Pevec, Simon; Becker, Martin; Dellith, Jan; Rothhardt, Manfred; Marques, Manuel B; Donlagic, Denis; Bartelt, Hartmut; Frazão, Orlando

    2014-06-01

    Focused ion beam technology is combined with chemical etching of specifically designed fibers to create Fabry-Perot interferometers. Hydrofluoric acid is used to etch special fibers and create microwires with diameters of 15 μm. These microwires are then milled with a focused ion beam to create two different structures: an indented Fabry-Perot structure and a cantilever Fabry-Perot structure that are characterized in terms of temperature. The cantilever structure is also sensitive to vibrations and is capable of measuring frequencies in the range 1 Hz - 40 kHz.

  2. Theoretical investigation of the optical and EPR parameters for VO 2+ion in some complexes

    Science.gov (United States)

    Kalfaoğlu, Emel; Karabulut, Bünyamin

    2012-04-01

    The molecular orbital coefficients and the EPR parameters of trisodium citrate dihydrate, sodium hydrogen oxalate monohydrate, potassium d-gluconate monohydrate and L-Alanine vanadyl complexes are calculated theoretically. Two d-d transition spectra and EPR parameters for the VO2+ complex are calculated theoretically by using crystal-field theory. The calculated g and A paramaters have indicated that paramagnetic center is axially symmetric. Having the relations of g∥A⊥ for VO2+ ions, it can be concluded that VO2+ ions are located in distorted octahedral sites (C4v) elongated along the z-axis and the ground state of the paramagnetic electron is dxy.

  3. Experimental simulation of radiation damage of polymers in space applications by cosmic-ray-type high energy heavy ions and the resulting changes in optical properties

    Science.gov (United States)

    Hossain, U. H.; Ensinger, W.

    2015-12-01

    Devices operating in space, e.g. in satellites, are being hit by cosmic rays. These include so-called HZE-ions, with High mass (Z) and energy (E). These highly energetic heavy ions penetrate deeply into the materials and deposit a large amount of energy, typically several keV per nm range. Serious damage is created. In space vehicles, polymers are used which are degraded under ion bombardment. HZE ion irradiation can experimentally be simulated in large scale accelerators. In the present study, the radiation damage of aliphatic vinyl- and fluoro-polymers by heavy ions with energies in the GeV range is described. The ions cause bond scission and create volatile small molecular species, leading to considerable mass loss of the polymers. Since hydrogen, oxygen and fluorine-containing molecules are created and these elements are depleted, the remaining material is carbon-richer than the original polymers and contains conjugated CC double bonds. This process is investigated by measuring the optical band gap with UV-Vis absorption spectrometry as a function of ion fluence. The results show how the optical band gaps shift from the UV into the Vis region upon ion irradiation for the different polymers.

  4. Dose reconstruction in irradiated Fricke-agarose gels by means of MRI and optical techniques: 2D modelling of diffusion of ferric ions

    Energy Technology Data Exchange (ETDEWEB)

    Pasquale, F. de; Luciani, A.M.; Pacilio, M.; Guidoni, L.; Viti, V.; D' Errico, F.; Barone, P.; Sebastiani, G

    2002-07-01

    Fricke-agarose gels have elicited much interest in the field of radiation dosimetry, as tissue-equivalent dosemeters. Magnetic resonance (MR) relaxation rates are measured for dose reconstruction. A major problem of Fricke-agarose gels is the diffusion of the ferric ions formed after irradiation. Knowledge of the diffusion coefficient of ferric ions may be necessary. Xylene orange, a dye that specifically chelates ferric ions, was added to the Fricke gel system to reduce ion diffusion and, as the binding gives a coloured complex, to allow optical detection of ferric ions. Diffusion of ferric ions in two dimensions and time evolution of ion concentration were evaluated. MR images were obtained at different times after irradiation. Ferric ion distribution, the corresponding images and the doses at different times after irradiation were reconstructed taking into account the calculated diffusion coefficients. Diffusion was then estimated by means of two different optical methods. The agreement obtained supports the reliability of the MRI method and of the model. (author)

  5. Experimental simulation of radiation damage of polymers in space applications by cosmic-ray-type high energy heavy ions and the resulting changes in optical properties

    Energy Technology Data Exchange (ETDEWEB)

    Hossain, U.H.; Ensinger, W., E-mail: ensinger@ca.tu-darmstadt.de

    2015-12-15

    Devices operating in space, e.g. in satellites, are being hit by cosmic rays. These include so-called HZE-ions, with High mass (Z) and energy (E). These highly energetic heavy ions penetrate deeply into the materials and deposit a large amount of energy, typically several keV per nm range. Serious damage is created. In space vehicles, polymers are used which are degraded under ion bombardment. HZE ion irradiation can experimentally be simulated in large scale accelerators. In the present study, the radiation damage of aliphatic vinyl- and fluoro-polymers by heavy ions with energies in the GeV range is described. The ions cause bond scission and create volatile small molecular species, leading to considerable mass loss of the polymers. Since hydrogen, oxygen and fluorine-containing molecules are created and these elements are depleted, the remaining material is carbon-richer than the original polymers and contains conjugated CC double bonds. This process is investigated by measuring the optical band gap with UV–Vis absorption spectrometry as a function of ion fluence. The results show how the optical band gaps shift from the UV into the Vis region upon ion irradiation for the different polymers.

  6. Effect of 50MeV Li3+ ion irradiation on structural, optical and electrical properties of amorphous Se95Zn5 thin films

    Science.gov (United States)

    Ahmad, Shabir; Sethi, Riti; Nasir, Mohd.; Asokan, K.; Zulfequar, M.

    2015-08-01

    Present work focuses on the effect of swift heavy ion (SHI) irradiation of 50MeV Li3+ ions by varying the fluencies in the range of 1×1012 to 5×1013 ions/cm2 on the morphological, structural, optical and electrical properties of amorphous Se95Zn5 thin films. Thin films of ~250nm thickness were deposited on cleaned glass substrates by thermal evaporation technique. X-ray diffraction (XRD) analysis shows the pristine thin film of Se95Zn5 growsin hexagonal phase structure. Also it was found that the small peak observed in XRD spectra vanishes after SHI irradiation indicates the defects of the material increases. The optical parameters: absorption coefficient (α), extinction coefficient (K), refractive index (n) optical band gap (Eg) and Urbach's energy (EU) are determined from optical absorption spectra data measured from spectrophotometry in the wavelength range 200-1000nm. It was found that the values of absorption coefficient, refractive index and extinction coefficient increases while the value optical band gap decreases with the increase of ion fluence. This post irradiation change in the optical parameters was interpreted in terms of bond distribution model. Electrical properties such as dc conductivity and temperature dependent photoconductivity of investigated thin films were carried out in the temperature range 309-370 K. Analysis of data shows activation energy of dark current is greater as compared to activation energy photocurrent. The value of activation energy decreases with the increase of ion fluence indicates that the defect density of states increases.Also it was found that the value of dc conductivity and photoconductivity increases with the increase of ion fluence.

  7. Optical characterization of Mn2+, Ni2+ and Co2+ ions doped zinc lead borate glasses

    Science.gov (United States)

    Thulasiramudu, A.; Buddhudu, S.

    2006-11-01

    This paper reports on the development and optical characterization of heavy metal oxide (HMO)-based transparent glasses in the chemical composition of 15PbO 40B2O3 (45-x) ZnO-x TM2+ (=Mn2+ or Ni2+ or Co2+) (where x=0.2, 0.5 mol%). For these glasses both absorption and emission spectra have been measured, in order to understand their optical performances. The XRD profiles have confirmed their glassy nature and the FTIR spectral features have been analyzed. From the emission spectra, a bright green emission (538 nm) from Mn2+-glasses, an intense red emission (670 nm) from Ni2+ and from Co2+ (625 nm) glasses have been noticed very clearly. Based on the UV-absorption spectra of these materials, both direct and indirect bond gaps have been computed. Apart from the spectral analysis, different physical properties of these glasses have also been carried out. Due to the presence of both PbO and ZnO, these glasses are found to be good moisture-resistant optical systems. Both optical and physical properties have been found to be more encouraging towards their use as novel luminescent optical materials.

  8. Experiences With The Reactive Low Voltage Ion Plating In Optical Thin Film Production

    Science.gov (United States)

    Guertler, Karlheinz; Jeschkowski, Ulrich; Conrath, E.

    1989-02-01

    The transmission of interference filters consisting of Ta205, Ti02, Zr02 and Si02 layers were measured at temperatures between 25°C and 185°C. Some characteristic differences between filters produced by reactive evaporation and reactive ion plating are demonstrated and discussed.

  9. Optical properties in the Cu-fused silica system irradiated with swift heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, Ranjana C. [Department of Physics, University of Mumbai, Vidyanagari, Santacruz East, Mumbai 400 098 (India); Kothari, D.C. [Department of Physics, University of Mumbai, Vidyanagari, Santacruz East, Mumbai 400 098 (India)]. E-mail: kothari@mu.ac.in; Choudhari, R.J. [Nuclear Science Centre, P.O. Box 10502, Aruna Asaf Ali Marg, New Delhi 110 067 (India); Kumar, Ravi [Nuclear Science Centre, P.O. Box 10502, Aruna Asaf Ali Marg, New Delhi 110 067 (India); Sahoo, P.K. [II. Physikalisches Institut, Universitaet Goettingen, Friedrich-Hund-Platz 1, D-37077 Goettingen (Germany); Lieb, K.P. [II. Physikalisches Institut, Universitaet Goettingen, Friedrich-Hund-Platz 1, D-37077 Goettingen (Germany); Klaumuenzer, S. [Hahn-Meitner Institut, Glienicker Str. 100, D-14109 Berlin (Germany)

    2006-04-15

    Swift heavy ions are used to study the effects of electronic energy loss on Cu cluster formation in fused silica after post-irradiation annealing. Fused silica substrates covered with 10 nm thin Cu-films were irradiated using beams of either 120 MeV Ag{sup 9+} ions or 350 MeV Au{sup 26+} ions at fluences ranging from 2 x 10{sup 13} to 1 x 10{sup 14} cm{sup -2}. After irradiation, the samples were annealed for 30 min in argon, at temperatures of 773-1200 K and characterized by UV-VIS absorption spectroscopy. The swift ion irradiations created E' and B{sub 2} defects in silica, which were partially eliminated during annealing. In addition, Cu cluster formation in silica was observed after annealing. Irradiation fluences exceeding 4 x 10{sup 13} cm{sup -2} and annealing temperatures above 1100 K are more effective in forming larger nanoclusters.

  10. Optical Observation of Oxygen Ion Upflow in the Cusp/Cleft Region

    Science.gov (United States)

    Tashiro, S.; Yamazaki, A.; Yoshikawa, I.; Takizawa, Y.; Ogawa, Y.; Miyake, W.; Nakamura, M.

    2002-12-01

    We built the Extreme ultraviolet scanner (XUV) for imaging oxygen ions to outflow from the polar ionosphere into the magnetosphere. The XUV onboard a sounding rocket SS-520-2 imaged the oxygen ions above 1000 km altitude near the polar cusp on December 4, 2000. The XUV is a normal incidence telescope that has a peak sensitivity at the wavelength 83.4 nm of OII emission and consists of a Mo coated mirror, a band pass filter and a channel electron multiplier. The band pass filter selectively transmits OII emission and eliminates background emissions such as HeI emission at the 30.4 nm, HeII emission at the 58.4 nm, and HI emission at the 121.6 nm. The observed OII emission intensity is proportional to the ion density integrated along the line of sight. Therefore the observed OII emission intensity distribution makes possible to determine the oxygen ion distribution. After 0928UT, the sudden increase in the OII emission intensity was observed from the cusp region identified by the radar observation. In this presentation, we will discuss the cause of the sudden increase in the OII emission intensity in comparison with the result of ground-based observations.

  11. Formation of Optical Waveguide and Annealing Behaviour of LiNbO3 Implanted by 3.0- MeV Nickel Ions

    Institute of Scientific and Technical Information of China (English)

    ZHANG Ting-Ting; LU Fei; LI Shi-Ling; WANG Xue-Lin; SHEN Ding-Yu; MA Hong-Ji

    2004-01-01

    @@ The optically polished LiNbO3 crystal was implanted with 3.0 MeV nickel ions to a dose of 8 × 10T14 ions/cm2. The implanted sample was orderly annealed at different temperatures for different times in air ambient. The waveguide properties before and after annealing were investigated. Dark modes were observed by the prism coupling technique. The reconstructed refractive index profiles were obtained with the reflectivity calculation method.

  12. Study of structural and optical properties of lead borate glasses containing transition metal ion

    Science.gov (United States)

    Sanjay, Kaushik, A.; Kishore, N.; Agarwal, A.; Pal, I.; Dhar, R.

    2012-06-01

    Glasses with compositions xFe2O3.(40-x)PbO.60B2O3: V2O5 (2 mol%) have been prepared by the standard melt-quenching technique. Various properties such as glass transition temperature, density, IR spectra and optical band gap energy have been studied. The structural changes in these glasses have been monitored by IR spectroscopy. The values of optical band gap for indirect allowed and indirect forbidden transitions have been determined using available theories. The Urbach's energy is used to characterize the degree of disorder in amorphous solids.

  13. DSC, ESR and optical absorption studies of Cu{sup 2+} ion doped in boro cadmium tellurite glasses

    Energy Technology Data Exchange (ETDEWEB)

    Gayathri Pavani, P., E-mail: gayathri.potturi@gmail.com [Glassy Material Research Laboratory, Department of Physics, Osmania University, Hyderabad 500 007 (India); Prasad, M.; Chandra Mouli, V. [Glassy Material Research Laboratory, Department of Physics, Osmania University, Hyderabad 500 007 (India)

    2012-06-25

    Highlights: Black-Right-Pointing-Pointer Variation in different physical parameters of the glass system is studied. Black-Right-Pointing-Pointer Variation in glass transition temperature is discussed in terms of different structural parameters. Black-Right-Pointing-Pointer ESR analysis and the bonding parameters determination of the present glass system is interesting. - Abstract: Physical, optical absorption, ESR and DSC studies on 50 B{sub 2}O{sub 3}-(50 - x) CdO-xTeO{sub 2} glasses containing Cu{sup 2+} spin probe have been carried out. Density measurement is carried out by Archimedes principle. Variation in glass transition temperature is discussed in terms of physical parameters. ESR results show that g{sub Parallel-To} > g{sub Up-Tack} indicating that the Cu{sup 2+} ions is in tetragonal distorted octahedral site and its ground state is d{sub x{sub 2-y{sub 2}}}. There are considerable changes in g{sub Parallel-To }, g{sub Up-Tack} and A{sub Parallel-To} values with increasing the concentration of CdO in BCT glass systems. The optical absorption spectra results show that the absorption peak of Cu{sup 2+} is a function of composition. The observed optical absorption peak of Cu{sup 2+} has been found to be minimum at 776 nm for x = 30 mol.% of CdO content. The variations in the physical, optical and bonding parameters clearly indicate the structural changes in the present glass system with varied CdO content.

  14. Effects of varying base glass composition on the optical properties of lead borate glasses doped with rare earth ions

    Science.gov (United States)

    Heidorn, William D.

    Rare Earth (RE) doped lead borate glasses are expected to exhibit a compositional dependence in their optical properties due to the changes induced by variations in the structure of the base glass with increasing lead oxide content. A series of lead borate glasses with the composition xPbO:(99.5 - x)B2O 3 (x = 29.5 to 69.5 in steps of 10 mol%) doped with 0.5 mol% Sm2O3, Er2O3, and Ho2O3 were prepared using the melt quench technique followed by 3 hours of annealing near the glass transition temperature. Optical absorption and fluorescence spectra of these RE doped lead borate glasses were analyzed using Judd-Ofelt theory. The compositional dependence of Judd-Ofelt intensity parameters, O t (t = 2, 4, 6), were determined and were then used to calculate the radiative transition probability of the excited states, the total radiative transition probability, branching ratios, and radiative lifetime of the glasses. From the fluorescence spectra the stimulated emission cross section, and Stark splitting of the excited states were calculated as a function of glass composition. A fourth set of samples with composition xPbO:(99 - x)B2O 3(x = 29 to 69 in steps of 10 mol%) co-doped with 0.5 mol% Er2 O3 and Ho2O3 were also prepared and the effects of co-doping on the absorption and fluorescence were analyzed. In all the glass systems studied, it was found that the optical properties are strongly influenced by structural changes arising from compositional variation. Er3+ transitions exhibit large stimulated cross section suggesting the possible utilization of these materials in laser applications. Keywords: Lead and bismuth borate glasses, fluorescence, optical absorption, Sm3+, Ho3+, Er3+ ions, Judd-Ofelt intensity parameters, stimulated emission cross section.

  15. Crystallization of mullite from kaolin according to optical spectroscopy of impurity ions

    Science.gov (United States)

    Igo, A. V.

    2017-06-01

    The luminescence spectra of Cr3+ and Eu3+ ions embedded in mullite ceramic samples are studied. The samples were annealed at temperatures from 600 to 1200°C. Beginning at a temperature of 890°C, the spectra demonstrated the presence of a newly formed crystal phase. At temperatures from 920 to 1200°C, the crystalline form manifested itself as a stable mullite phase. A temperature of 920°C corresponded to a sharp change in the symmetry of the crystal field around Eu3+ (phase transition). The parameters of the spectral lines of ions were used to estimate the mullite crystal-lattice disorder and the residual deformations in ceramic samples. The spread of the mullite crystal-lattice parameter is determined as |Δ a/a| ≈ 0.028 and is independent of the annealing temperature.

  16. Novel optical selective chromone Schiff base chemosensor for Al{sup 3+} ion

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Chun-jiao; Yang, Zheng-yin, E-mail: yangzy@lzu.edu.cn; Fan, Long; Jin, Xiu-long; An, Jun-mei; Cheng, Xiao-ying; Wang, Bao-dui

    2015-02-15

    A novel Schiff-base fluorescent sensor 7-methoxychromone-3-carbaldehyde-((2′-Benzothiazolylthio)-acetyl) hydrazone (MCAH) was synthesized. The new chemosensor possesses dual PET processes simultaneously introducing by both nitrogen and sulfur donors. Upon binding Al{sup 3+}, a significant fluorescence enhancement with a turn-on ratio over 500-fold was triggered. The detection limit of MCAH for Al{sup 3+} was 3.19×10{sup −8} M. - Highlights: • A novel chemosensor based on multiple PET processes was synthesized by a facile one-step reaction. • The sensor exhibits higher sensitivity for Al{sup 3+} than other metal ions with the detection limit reaching at 10{sup −8} M level in ethanol. • The probe exhibited high selectivity for Al{sup 3+} over other metal ions with 500-fold fluorescence enhancement.

  17. Preparation and optical spectroscopy of phosphate glasses containing divalent europium ions

    Institute of Scientific and Technical Information of China (English)

    Haiping Xia(夏海平); Hongwei Song(宋宏伟); Qiuhua Nie(聂秋华); Jianli Zhang(章践立); Jinhao Wang(王金浩); Jiwei Wang(王绩伟); Tiefeng Xu(徐铁峰); Jiaha Zhang(张家骅)

    2003-01-01

    P2O5.BaO.Na2O.K2O glasses doped with various content of Eu2O3 were prepared using high temperaturemelting method, and the Eu 2+ ions in the phosphate glasses were obtained with the aid of the reductiveaction of silicon powder. The fabricating conditions, fluorescence, excitation spectra of the glasses werethen studied. The glasses containing europium show a broad emission band at 450 nm and sharp bandsfrom 580 to 650 nm, and the co-existence of Eu2+ and Eu3+ is identified. Also, a good glass with adominant proportion and large quantity of Eu2+ ions can be obtained by the reductive action of siliconpowder and proper processing.

  18. Scattering of hydrogen, nitrogen and water ions from micro pore optic plates for application in spaceborne plasma instrumentation

    Science.gov (United States)

    Stude, Joan; Wieser, Martin; Barabash, Stas

    2016-10-01

    Time-of-flight mass spectrometers for upcoming space missions into enhanced radiation environments need to be small, light weight and energy efficient. Time-of-flight systems using surface interactions as start-event generation can be smaller than foil-type instruments. Start surfaces for such applications need to provide narrow angular scattering, high ionization yields and high secondary electron emissions to be effective. We measured the angular scattering, energy distribution and positive ionization yield of micro pore optics for incident hydrogen, nitrogen and water ions at 2 keV. Positive ionization yields of 2% for H+ , 0.5% for N+ and 0.2% for H2O+ were detected.

  19. Note: Optical fiber milled by focused ion beam and its application for Fabry-Pérot refractive index sensor

    DEFF Research Database (Denmark)

    Yuan, Scott Wu; Wang, Fei; Savenko, Alexey;

    2011-01-01

    We introduce a highly compact fiber-optic Fabry-Pérot refractive index sensor integrated with a fluid channel that is fabricated directly near the tip of a 32 μm in diameter single-mode fiber taper. The focused ion beam technique is used to efficiently mill the microcavity from the fiber side...... and finely polish the end facets of the cavity with a high spatial resolution. It is found that a fringe visibility of over 15 dB can be achieved and that the sensor has a sensitivity of ∼1731 nm/RIU (refractive index units) and a detection limit of ∼5.78 × 10−6 RIU. This miniature integrated all-in-fiber...

  20. Manual of the Option.com program (ion optics); Manual del programa Option.com

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez B, M

    1991-02-15

    The laws that govern the trajectory that follow the charged particles in the hole, inside magnetic fields (to first approach) are similar to those of the geometric classic optics by it to observe a graph of the trajectories gives an excellent understanding of that is happening to the beam. The object of this program is that besides providing the numeric data of the solution of the problem of the transverse section of the beam, be also shown a graph of the trajectories but external regarding the optic axis in the treated region and aid the user asking in the case of a system of two quadrupoles, where it is wanted to focus the beam. (Author)

  1. Computer modelling of the optical properties of transition-metal ions in solids

    Energy Technology Data Exchange (ETDEWEB)

    Bartram, R.H. [Univ. of Connecticut, Storrs, CT (United States)

    1994-12-31

    Computational methods for modeling the optical properties of substitutional transition-metal impurities in insulating solids, potentially applicable to some scintillator and phosphor materials, are reviewed. Methods considered include crystal-field and semiempirical ligand-field models; SCF-X{alpha}-SW, SCF-RHF-LCAO, SCF-UHF-LCAO and CI ab initio methods; and ICECAP and HADESR embedded-cluster methods with lattice relaxation. A detailed example of the application of the HADESR method to crystal-field spectra of Cr{sup 3+} in halide elpasolites is described. In this method, ab initio molecular-orbital calculations with effective core potentials are performed for selected ionic configurations. Simultaneous relaxation of the cluster and surrounding lattice, with mutual pair-potential interactions, is accomplished by a modified lattice statics program. properties include pressure-dependent optical transition energies, vibration frequencies and radiationless transition rates.

  2. Beam optical design of in-flight fragment separator for high-power heavy ion beam

    Energy Technology Data Exchange (ETDEWEB)

    Yun, C.C.; Kim, Mi-Jung; Kim, D.G.; Song, J.S.; Kim, Myeong-Jin [Rare Isotope Science Project, Institute for Basic Science, Daejeon 305-811 (Korea, Republic of); Kim, J.W., E-mail: jwkim@ibs.re.kr [Rare Isotope Science Project, Institute for Basic Science, Daejeon 305-811 (Korea, Republic of); Kim, J.R. [Department of Physics, Chung-Ang University, Seoul 156-756 (Korea, Republic of); Wan, W. [Accelerator Division, Lawrence Berkeley Laboratory, Berkeley, CA 94720 (United States)

    2013-12-15

    Highlights: • An in-flight fragment separator is designed in beam optics using GICOSY, COSY Infinity, LISE++ and MOCADI. • High power primary beam is removed in the pre-separator employing four dipole magnets. • Different charge states of the primary and unwanted isotope beams help in reducing peak power density at the beam dump. -- Abstract: An in-flight fragment separator has been designed for the rare isotope science project (RISP) in Korea. A beam used for the design is {sup 238}U in the energy of 200 MeV/u with the maximum beam power of 400 kW. The use of high-power beam requires careful removal of the primary beam by pre-separator, for which its configuration was revised to employ four dipole magnets instead of two. Different configurations of the separator have been tested in search of optimal design in non-linear optics, which was complicated by the space needed for the target, beam dump and radiation shielding. Non-linear optical calculations have been carried out using GICOSY and COSY Infinity including the fringe fields of large-aperture quadrupole magnets. Correction of non-linear terms is made with multipole coils located inside the superconducting quadrupole magnets and by external multipole magnets. Beam simulations using LISE++ and MOCADI have been performed to consider the effects of multiple charge states of the primary and isotope beams produced at the target. Layout of the separator is being finalized, and detailed optics simulation will continue to refine its design.

  3. [Calculation and analysis of optical transitions of Pr3+ ions in fluoride glass].

    Science.gov (United States)

    Kang, Dong-guo; Chen, Xiao-bo; Li, Song; Cui, Jian-sheng; Cai, Qing; Yu, Bao-Ting

    2007-01-01

    Intensity parameters of Pr3+ in ZBLAN glass were calculated using Judd-Ofelt(J-O) theory with absorption spectrum measurement. The anomalous behavior of Pr3+ was discussed using J-O theory. Base on the intensity parameters, the optical parameters such as spontaneous emission rate, branching ratio, and integrated emission cross section etc were predicted. The future of the glass as a laser material was discussed, and the probability of photon avalanche in the material was also analysed.

  4. Influence of Fe ions on structural, optical and thermal properties of SnO{sub 2} nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Ahmed, Ateeq, E-mail: ateeqamu124@gmail.com; Tripathi, P.; Khan, Wasi; Dar, Abid Ahmed; Ali, Tinku [Centre of Excellence in Material Science (Nanomaterials), Department of Applied Physics, Z.H. College of Engg. & Tech., Aligarh Muslim University, Aligarh-202002, Uttar Pradesh (India)

    2016-05-23

    In the present work, Fe doped SnO{sub 2} nanoparticles with the composition Sn{sub 1-x}Fe{sub x}O{sub 2} (x = 0, 0.02, 0.04 and 0.06) have been successfully synthesized using sol-gel auto combustion technique. The samples are characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Energy dispersive X-ray analysis (EDAX), Ultraviolet (UV-Visible) absorption spectroscopy and thermal gravimetric analysis (TGA). The XRD study shows that all the samples have been found in tetragonal rutile structure without any extra phase and average crystallite size which lies in the range of 6-17 nm. The EDAX spectrum confirmed the doping of Fe ion into tin oxide nanomaterial. The optical band gap of doped SnO{sub 2} is found to decrease with increasing Fe ion concentration, which is due to the formation of donor energy levels in the actual band gap of SnO{sub 2}.

  5. Optical and magnetic properties of Yb ion-doped cobalt-based ZnO nanoparticles for DMS applications

    Indian Academy of Sciences (India)

    T Thangeeswari; M Priya; J Velmurugan; N Padmanathan

    2015-09-01

    Well-crystalline structured ZnO nanoparticles with cobalt (Co) and ytterbium (Yb) multiple ions doping were successfully synthesized by the chemical precipitation technique. The structures, optical and magnetic properties of the samples were analysed with X-ray diffraction (XRD), UV–visible spectroscopy and magnetic measurements, respectively. In the XRD pattern of the pure ZnO and Yb co-doped samples, the formation of highly crystalline phase of pure ZnO was observed even at high Yb concentration. UV–vis spectra show a strong UV absorbance for all the samples with different absorbance maxima. Magnetic characterizations have shown that the sample with 1% Yb co-doped ZnO: Co nanoparticles exhibited a clear ferromagnetic (FM) behaviour at room temperature. The X-ray photoelectron spectral peaks for Yb 4f ions reveal Yb occupation of both Yb3+ as well as Yb2+ states. Hence, it can be confirmed that a clear FM behaviour at room temperature was exhibited by an imbalanced valence state of Yb that strongly interacted with the Co2+. When compared to the Co-doped ZnO, Yb co-doped ZnO exhibits a clear ferromagnetism at room temperature with high coercivity due to the contribution of both 3d and 4f exchange interaction with the host matrix.

  6. Development of electron optical system using annular pupils for scanning transmission electron microscope by focused ion beam

    Energy Technology Data Exchange (ETDEWEB)

    Matsutani, Takaomi, E-mail: matutani@ele.kindai.ac.jp [Kinki University, 3-4-1 Kowakae, Higashiosaka, Osaka 577-8502 (Japan); Yasumoto, Tsuchika; Tanaka, Takeo [Osaka Sangyo University, 3-1-1 Nakagaito, Daito, Osaka 574-8530 (Japan); Kawasaki, Tadahiro; Ichihashi, Mikio [Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Ikuta, Takashi [Osaka Electro-Communication University, 18-8 Hatsu-cho, Neyagawa, Osaka 572-8530 (Japan)

    2012-02-01

    Annular pupils for electron optics were produced using a focused ion beam (FIB), enabling an increase in the depth of focus and allowing for aberration-free imaging and separation of the amplitude and phase images in a scanning transmission electron microscope (STEM). Simulations demonstrate that an increased focal depth is advantageous for three-dimensional tomography in the STEM. For a 200 kV electron beam, the focal depth is increased to approximately 100 nm by using an annular pupil with inner and outer semi-angles of 29 and 30 mrad, respectively. Annular pupils were designed with various outer diameters of 40-120 {mu}m and the inner diameter was designed at 80% of the outer diameter. A taper angle varying from 1 Degree-Sign to 20 Degree-Sign was applied to the slits of the annular pupils to suppress the influence of high-energy electron scattering. The fabricated annular pupils were inspected by scanning ion beam microscopy and scanning electron microscopy. These annular pupils were loaded into a STEM and no charge-up effects were observed in the scintillator projection images recorded by a CCD camera.

  7. Beam optical design of in-flight fragment separator for high-power heavy ion beam

    Science.gov (United States)

    Yun, C. C.; Kim, Mi-Jung; Kim, D. G.; Song, J. S.; Kim, Myeong-Jin; Kim, J. W.; Kim, J. R.; Wan, W.

    2013-12-01

    An in-flight fragment separator has been designed for the rare isotope science project (RISP) in Korea. A beam used for the design is 238U in the energy of 200 MeV/u with the maximum beam power of 400 kW. The use of high-power beam requires careful removal of the primary beam by pre-separator, for which its configuration was revised to employ four dipole magnets instead of two. Different configurations of the separator have been tested in search of optimal design in non-linear optics, which was complicated by the space needed for the target, beam dump and radiation shielding. Non-linear optical calculations have been carried out using GICOSY and COSY Infinity including the fringe fields of large-aperture quadrupole magnets. Correction of non-linear terms is made with multipole coils located inside the superconducting quadrupole magnets and by external multipole magnets. Beam simulations using LISE++ and MOCADI have been performed to consider the effects of multiple charge states of the primary and isotope beams produced at the target. Layout of the separator is being finalized, and detailed optics simulation will continue to refine its design.

  8. Laser and optical system for laser assisted hydrogen ion beam stripping at SNS

    Science.gov (United States)

    Liu, Y.; Rakhman, A.; Menshov, A.; Webster, A.; Gorlov, T.; Aleksandrov, A.; Cousineau, S.

    2017-03-01

    Recently, a high-efficiency laser assisted hydrogen ion (H-) beam stripping was successfully carried out in the Spallation Neutron Source (SNS) accelerator. The experiment was not only an important step toward foil-less H- stripping for charge exchange injection, it also set up a first example of using megawatt ultraviolet (UV) laser source in an operational high power proton accelerator facility. This paper reports in detail the design, installation, and commissioning result of a macro-pulsed multi-megawatt UV laser system and laser beam transport line for the laser stripping experiment.

  9. An Optical Fiber-Based Sensor Array for the Monitoring of Zinc and Copper Ions in Aqueous Environments

    Directory of Open Access Journals (Sweden)

    Steven Kopitzke

    2014-02-01

    Full Text Available Copper and zinc are elements commonly used in industrial applications as aqueous solutions. Before the solutions can be discharged into civil or native waterways, waste treatment processes must be undertaken to ensure compliance with government guidelines restricting the concentration of ions discharged in solution. While currently there are methods of analysis available to monitor these solutions, each method has disadvantages, be it high costs, inaccuracy, and/or being time-consuming. In this work, a new optical fiber-based platform capable of providing fast and accurate results when performing solution analysis for these metals is described. Fluorescent compounds that exhibit a high sensitivity and selectivity for either zinc or copper have been employed for fabricating the sensors. These sensors demonstrated sub-part-per-million detection limits, 30-second response times, and the ability to analyze samples with an average error of under 10%. The inclusion of a fluorescent compound as a reference material to compensate for fluctuations from pulsed excitation sources has further increased the reliability and accuracy of each sensor. Finally, after developing sensors capable of monitoring zinc and copper individually, these sensors are combined to form a single optical fiber sensor array capable of simultaneously monitoring concentration changes in zinc and copper in aqueous environments.

  10. Optical refractive index and static permittivity of mixed Zr-Si oxide thin films prepared by ion beam induced CVD

    Energy Technology Data Exchange (ETDEWEB)

    Ferrer, F.J. [Centro Nacional de Aceleradores, Av. Thomas A. Edison, 7, 41092 Sevilla (Spain)], E-mail: fjferrer@us.es; Frutos, F. [E.T.S. de Ingenieria Informatica, Avda. Reina Mercedes, s/n, 41012 Sevilla (Spain); Garcia-Lopez, J. [Centro Nacional de Aceleradores, Av. Thomas A. Edison, 7, 41092 Sevilla (Spain); Gonzalez-Elipe, A.R.; Yubero, F. [Insituto de Ciencia de Materiales de Sevilla, c/ Americo vespucio, no. 49, 41092 Sevilla (Spain)

    2007-12-03

    Mixed oxides Zr{sub x}Si{sub 1-x}O{sub 2} (0 < x < 1) thin films have been prepared at room temperature by decomposition of (CH{sub 3}CH{sub 2}O){sub 3}SiH and Zr[OC(CH{sub 3}){sub 3}]{sub 4} volatile precursors induced by mixtures of O{sub 2}{sup +} and Ar{sup +} ions. The films were flat and amorphous independently of the Si/Zr ratio and did not present phase segregation of the pure single oxides (SiO{sub 2} and ZrO{sub 2}). A 10-23 at.% of H and 1-5 at.% of C atoms remained incorporated in the films depending on the mixture ratio of the Si and Zr precursors and the composition of the bombarding gas used during the deposition process. These impurities are mainly forming hydroxyl and carboxylic groups. Optical refractive index and static permittivity of the films were determined by reflection NIR-Vis spectroscopy and C-V electrical characterization, respectively. It is found that the refractive index increases non-linearly from 1.45 to 2.10 as the Zr content in the thin films increases. The static permittivity also increases non-linearly from {approx} 4 for pure SiO{sub 2} to {approx} 15 for pure ZrO{sub 2}. Optical and electrical characteristics of the films are justified by their impurity content and the available theories.

  11. An optical MEMS accelerometer fabricated using double-sided deep reactive ion etching on silicon-on-insulator wafer

    Science.gov (United States)

    Teo, Adrian J. T.; Li, Holden; Tan, Say Hwa; Yoon, Yong-Jin

    2017-06-01

    Optical MEMS devices provide fast detection, electromagnetic resilience and high sensitivity. Using this technology, an optical gratings based accelerometer design concept was developed for seismic motion detection purposes that provides miniaturization, high manufacturability, low costs and high sensitivity. Detailed in-house fabrication procedures of a double-sided deep reactive ion etching (DRIE) on a silicon-on-insulator (SOI) wafer for a micro opto electro mechanical system (MOEMS) device are presented and discussed. Experimental results obtained show that the conceptual device successfully captured motion similar to a commercial accelerometer with an average sensitivity of 13.6 mV G-1, and a highest recorded sensitivity of 44.1 mV G-1. A noise level of 13.5 mV was detected due to experimental setup limitations. This is the first MOEMS accelerometer developed using double-sided DRIE on SOI wafer for the application of seismic motion detection, and is a breakthrough technology platform to open up options for lower cost MOEMS devices.

  12. Using Monoclonal Antibody to Determine Lead Ions with a Localized Surface Plasmon Resonance Fiber-optic Biosensor

    Directory of Open Access Journals (Sweden)

    Mon-Fu Chung

    2008-01-01

    Full Text Available A novel reflection-based localized surface plasmon resonance (LSPR fiber-optic probe has been developed to determine the heavy metal lead ion concentration. Monoclonal antibody as the detecting probe containing massive amino groups to capture Pb(II-chelate complexes was immobilized onto gold nanoparticle-modified optical fiber (NMAuOF. The optimal immobilizing conditions of monoclonal antibody on to the NMAuOF are 189 μg/mL in pH7.4 PBS for 2 h at 25°C. The absorbability of the functionalized NMAuOF sensor increases to 12.2 % upon changing the Pb(II-EDTA level from 10 to 100 ppb with a detection limit of 0.27 ppb. The sensor retains 92.7 % of its original activity and gives reproducible results after storage in 5% D-( -Trehalose dehydrate solution at 4°C for 35 days. In conclusion, the monoclonal antibody-functionalized NMAuOF sensor shows a promising result for determining the concentration of Pb(II with high sensitivity.

  13. Controlling the optical fiber output beam profile by focused ion beam machining of a phase hologram on fiber tip.

    Science.gov (United States)

    Han, Jiho; Sparkes, Martin; O'Neill, William

    2015-02-01

    A phase hologram was machined on an optical fiber tip using a focused ion beam (FIB) system so that a ring-shaped beam emerges from the fiber tip. The fiber used for this work was a commercial single-mode optical fiber patch cable for a design wavelength of 633 nm with a germanosilicate core. The ring-shaped beam was chosen to ensure a simple geometry in the required phase hologram, though the Gerchberg-Saxton algorithm can be used to calculate a hologram for an arbitrary beam shape. The FIB machining took approximately 45 min at 30 kV and 200 pA. The radius of the resulting ring beam was 0.083 m at 1 m standoff, as compared to 0.1 m as was initially desired. Results suggest that this imaging technique may provide a basis for a beam-shaping method with several advantages over the current commercial solutions, having permanent alignment, compactness, and mechanical robustness. However, it would appear that minimizing the speckle pattern will remain a critical challenge for this technique to become widely implemented.

  14. Optics

    CERN Document Server

    Fincham, W H A

    2013-01-01

    Optics: Ninth Edition Optics: Ninth Edition covers the work necessary for the specialization in such subjects as ophthalmic optics, optical instruments and lens design. The text includes topics such as the propagation and behavior of light; reflection and refraction - their laws and how different media affect them; lenses - thick and thin, cylindrical and subcylindrical; photometry; dispersion and color; interference; and polarization. Also included are topics such as diffraction and holography; the limitation of beams in optical systems and its effects; and lens systems. The book is recommen

  15. Rare-Earth Ions in Niobium-Based Devices as a Quantum Memory: Magneto-Optical Effects on Room Temperature Electrical Transport

    Science.gov (United States)

    2016-09-01

    University of Delaware , Newark, DE. 5f. WORK UNIT NUMBER REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704-01-0188 The public reporting burden for...ANSI Std . Z39.18 September 2016 Final Rare-Earth Ions in Niobium-based Devices as a Quantum Memory Magneto-Optical Effects on Room Temperature

  16. Effect of Ni and Au ion irradiations on structural and optical properties of nanocrystalline Sb-doped SnO{sub 2} thin films

    Energy Technology Data Exchange (ETDEWEB)

    Mir, Feroz A. [University of Kashmir, University Science Instrumentation Centre, Srinagar, J and K (India); Batoo, Khalid Mujasam [King Saud University, King Abdullah Institute for Nanotechnology, Riyadh (Saudi Arabia)

    2016-04-15

    The effect of swift heavy ion irradiations on the structural and optical properties of 6 % Sb-doped SnO{sub 2} thin films deposited on quartz substrate by electron beam evaporation technique is presented. Two ion species Ni and Au with energy 120 MeV and fluence of 1 x 10{sup 13} ion/cm{sup 2} were used. These films were characterized by X-ray diffraction, atomic force microscope, UV-visible and micro-Raman spectroscopy. From structural analysis, these films exhibit tetragonal rutile structure and retain it even after irradiation. The ion irradiations have shown improvement in the structural properties, such as increase in grain size and decrease in the lattice strain. Raman study also indicates enhancement in quality of crystal structure after irradiations. The grain growth after ion interaction is also observed by atomic force microscope study. Further, a variation in optical band gap and reduction in disorder is observed after irradiation. Other parameters such as Urbach tails energy and steepness parameter are obtained from optical data. The overall observed physical properties show a significant improvement after irradiation. A good correspondence between structures with its various properties can be seen. (orig.)

  17. Physical, Optical and Electron paramagnetic resonance studies of PbBr2-PbO-B2O3 glasses containing Cu2+ ions

    Science.gov (United States)

    Sekhar, K. Chandra; Hameed, Abdul; Chary, M. Narasimha; Shareefuddin, Md

    2016-09-01

    The glasses with the composition PbBr2-PbO-B2O3 glasses containing Cu2+ ions were prepared by melt quenching technique. X-ray diffractograms revealed the amorphous nature of the glasses. Density and molar volume were determined. Density is found to decrease while the molar volume increases with increase of PbBr2 content. The optical absorption spectra exhibited a broad band corresponding to the d- d transition of Cu2+ ion. From optical absorption spectra Eopt and Urbach energies were determined. Electron Paramagnetic Resonance (EPR) studies were carried out by introducing Cu2+ as the spin probe. Glasses containing transition metal(TM) ions such as Cu2+ give the information about the structure and the site symmetry around the TM ions. EPR spectra of all the glass samples were recorded at X-band frequencies. From the EPR spectra spin-Hamiltonian parameters were evaluated. It was observed that g∥ >g±>ge (2.0023) and A∥>A±. From this values it is concluded that the ground state of Cu2+ is dx2-y2 (2B1g) and the site symmetry around Cu2+ ion is tetragonally distorted octahedral. From the EPR and Optical data bonding coefficients were evaluated. The in plane o-bonding(α2) is moderately ionic while out of plane 7t-bonding(β2) and in plane 7t-bonding(β1 2) are ionic nature

  18. Study of laser-induced removal of co-deposits from tokamak plasma-facing components using ion diagnostics and optical spectroscopy

    Science.gov (United States)

    Wolowski, J.; Gasior, P.; Hoffman, J.; Kubkowska, M.; Rosinski, M.; Szymanski, Z.

    2010-10-01

    The paper presents studies of the application of ion diagnostics and optical spectroscopy for on-line measurement of the amount and characteristics of co-deposits from the laser-ablated surface of the plasma-facing components (e.g. graphite tiles). For removal of the co-deposit layer a repetitive Nd:YAG laser was used. Determination of the characteristics of ions emitted from the laser-illuminated targets was performed using ion collectors (on the basis of a time-of-flight method) and an optical spectrometer. The main ion stream parameters and spectral lines of deuterium and carbon or tungsten ions were measured depending on laser pulse parameters. The research proved that optical spectroscopy could be a convenient method for on-line observation of the co-deposited layer removal by means of laser ablation. In combination with the investigation of collected co-deposit dust, the performed study made it possible to state that laser-induced breakdown spectroscopy can be useful as a diagnostic method for the ablative co-deposited layer removal and the wall conditioning. The properties of modified surfaces of samples and collected dust (evaporated co-deposit) were determined using different measuring methods.

  19. Optical characterization of ion-doped crystalline and glassy matrices operating under hostile environmental conditions

    Science.gov (United States)

    Baccaro, S.; Cemmi, A.

    2016-10-01

    The aim of this work is to give an overall picture of the activity on gamma radiation effects in the field of scintillators (crystals, glasses) with specific mention to the role of ions doped in different crystalline and glassy matrices. Interesting results were obtained in terms of radiation hardness improvement and of physical-chemical properties modification as a function of the nature of dopant (i.e. rare earth as well as metallic ions) and of the scintillating host glassy and glass-ceramic matrix (silicate, phosphate, borate, oxyfluoride and mixed oxides glasses). The research activities were carried out at the 60Co gamma Calliope plant, a pool-type irradiation facility located at the Research Centre ENEA-Casaccia (Rome). Since the eighties, the Calliope facility is deeply involved in radiation processing research on materials and on devices to be used in hostile radiation environment such as nuclear plants, aerospace and High Energy Physics experiments, in the framework of international projects and collaboration with industries and research institutions.

  20. Optical absorption spectra of the uranium (4+) ion in the thorium germanate matrix

    CERN Document Server

    Gajek, Z; Antic-Fidancev, E

    1997-01-01

    Visible and infrared absorption measurements on the U sup 4 sup + ion in tetragonal zircon-type matrix beta-ThGeO sub 4 are reported and analysed in terms of the standard parametrization scheme. The observed 17 main peaks and a number of less intense lines have been assigned and fitted to most of the 32 allowed electric dipole transitions with the root mean square error equal to 65 cm sup - sup 1. The free-ion parameters obtained for the model Hamiltonian, zeta 5f = 1809 cm sup - sup 1 , F sup 2 =43 065 cm sup - sup 1 , F sup 4 =38 977 cm sup - sup 1 and F sup 6 =24 391 cm sup - sup 1 , as well as the corresponding crystal-field parameters, B sub 0 sup 2 =-1790 cm sup - sup 1 , B sub 0 sup 4 =1200 cm sup - sup 1 , B sub 4 sup 4 =3260 cm sup - sup 1 , B sub 0 sup 6 =-3170 cm sup - sup 1 and B sub 4 sup 6 =990 cm sup - sup 1 , agree fairly well with the initial theoretical estimations. The results are discussed in relation to the previous spectroscopic study on the scheelite-type matrix UGeO sub 4. (author)

  1. Implementation of Chiral Quantum Optics with Rydberg and Trapped-ion Setups

    CERN Document Server

    Vermersch, Benoît; Hauke, Philipp; Zoller, Peter

    2016-01-01

    We propose two setups for realizing a chiral quantum network, where two-level systems representing the nodes interact via directional emission into discrete waveguides, as introduced in Ref.~[T.\\ Ramos \\emph{et al.}, arXiv:1602.00926]. The first implementation realizes a spin waveguide via Rydberg states in a chain of atoms, whereas the second one realizes a phonon waveguide via the localized vibrations of a string of trapped ions. For both architectures, we show that strong chirality can be obtained by a proper design of synthetic gauge fields in the couplings from the nodes to the waveguide. In the Rydberg case, this is achieved via intrinsic spin-orbit coupling in the dipole-dipole interactions, while for the trapped ions it is obtained by engineered sideband transitions. We take long-range couplings into account that appear naturally in these implementations, discuss useful experimental parameters, and analyze potential error sources. Finally, we describe effects that can be observed in these implementati...

  2. Implementation of chiral quantum optics with Rydberg and trapped-ion setups

    Science.gov (United States)

    Vermersch, Benoît; Ramos, Tomás; Hauke, Philipp; Zoller, Peter

    2016-06-01

    We propose two setups for realizing a chiral quantum network, where two-level systems representing the nodes interact via directional emission into discrete waveguides, as introduced in T. Ramos et al. [Phys. Rev. A 93, 062104 (2016), 10.1103/PhysRevA.93.062104]. The first implementation realizes a spin waveguide via Rydberg states in a chain of atoms, whereas the second one realizes a phonon waveguide via the localized vibrations of a string of trapped ions. For both architectures, we show that strong chirality can be obtained by a proper design of synthetic gauge fields in the couplings from the nodes to the waveguide. In the Rydberg case, this is achieved via intrinsic spin-orbit coupling in the dipole-dipole interactions, while for the trapped ions it is obtained by engineered sideband transitions. We take long-range couplings into account that appear naturally in these implementations, discuss useful experimental parameters, and analyze potential error sources. Finally, we describe effects that can be observed in these implementations within state-of-the-art technology, such as the driven-dissipative formation of entangled dimer states.

  3. Site-selective ion beam synthesis and optical properties of individual CdSe nanocrystal quantum dots in a SiO₂ matrix.

    Science.gov (United States)

    Mangold, H Moritz; Karl, Helmut; Krenner, Hubert J

    2014-02-12

    Cadmium selenide nanocrystal quantum dots (NC-QDs) are site-selectively synthesized by sequential ion beam implantation of selenium and cadmium ions in a SiO2 matrix through submicrometer apertures followed by a rapid thermal annealing step. The structural and optical properties of the NC-QDs are controlled by the ion fluence during implantation and the diameter of the implantation aperture. For low fluences and small apertures the emission of these optically active emitters is blue-shifted compared to that of the bulk material by >100 meV due to quantum confinement. The emission exhibits spectral diffusion and blinking on a second time scales as established also for solution-synthesized NC-QDs.

  4. Synthesis and Characterization of Electroresponsive Materials with Applications In: Part I. Second Harmonic Generation. Part II. Organic-Lanthanide Ion Complexes for Electroluminescence and Optical Amplifiers.

    Science.gov (United States)

    Claude, Charles

    1995-01-01

    Materials for optical waveguides were developed from two different approaches, inorganic-organic composites and soft gel polymers. Inorganic-organic composites were developed from alkoxysilane and organically modified silanes based on nonlinear optical chromophores. Organically modified silanes based on N-((3^' -trialkoxysilyl)propyl)-4-nitroaniline were synthesized and sol-gelled with trimethoxysilane. After a densification process at 190^circC with a corona discharge, the second harmonic of the film was measured with a Nd:YAG laser with a fundamental wavelength of 1064nm, d_{33} = 13pm/V. The decay of the second harmonic was expressed by a stretched bi-exponential equation. The decay time (tau _2) was equal to 3374 hours, and was comparable to nonlinear optical systems based on epoxy/Disperse Orange 1. The processing temperature of the organically modified silane was limited to 200^circC due to the decomposition of the organic chromophore. Soft gel polymers were synthesized and characterized for the development of optical waveguides with dc-electrical field assisted phase-matching. Polymers based on 4-nitroaniline terminated poly(ethylene oxide-co-propylene oxide) were shown to exhibit second harmonic generation that were optically phase-matched in an electrical field. The optical signals were stable and reproducible. Siloxane polymers modified with 1-mercapto-4-nitrobenzene and 1-mercapto-4-methylsulfonylstilbene nonlinear optical chromophores were synthesized. The physical and the linear and nonlinear optical properties of the polymers were characterized. Waveguides were developed from the polymers which were optically phase -matched and had an efficiency of 8.1%. The siloxane polymers exhibited optical phase-matching in an applied electrical field and can be used with a semiconductor laser. Organic lanthanide ion complexes for electroluminescence and optical amplifiers were synthesized and characterized. The complexes were characterized for their thermal and

  5. High time resolution PFISR and optical observations of naturally enhanced ion acoustic lines

    Directory of Open Access Journals (Sweden)

    R. G. Michell

    2009-04-01

    Full Text Available Observations of naturally enhanced ion acoustic lines (NEIALs taken with the Poker Flat Incoherent Scatter Radar (PFISR using a mode with very high time resolution are presented. The auroral event took place over Poker Flat, Alaska on 8 February 2007 at 09:35 UT (~22:00 MLT, and the radar data are complemented by common-volume high-resolution auroral imaging. The NEIALs occurred during only one of the standard 15-s integration periods. The raw data of this time show very intermittent NEIALs which occur only during a few very short time intervals (≤1 s within the 15-s period. The time sampling of the raw data, ~19 ms on average, allows study of the time development of the NEIALs, though there are indications that even finer time resolution would be of interest. The analysis is based on the assumption that the NEIAL returns are the result of Bragg scattering from ion-acoustic waves that have been enhanced significantly above thermal levels. The spectra of the raw data indicate that although the up- and down-shifted shoulders can both become enhanced at the same time, (within 19 ms, they are most often enhanced individually. The overall power in the up-and down-shifted shoulders is approximately equal throughout the event, with the exception of one time, when very large up-shifted power was observed with no corresponding down-shifted power. This indicates that during the 480 μs pulse, the strongly enhanced ion-acoustic waves were only traveling downward and not upward. The exact time that the NEIALs occurred was when the radar beam was on the boundary of a fast-moving (~10 km/s, bright auroral structure, as seen in the high resolution auroral imaging of the magnetic zenith. When viewed with high time resolution, the occurrence of NEIALs is associated with rapid changes in auroral luminosity within the radar field of view due to fast-moving auroral fine structures.

  6. Structural and optical characteristics of Eu3+ ions in sodium-lead-zinc-lithium-borate glass system

    Science.gov (United States)

    Rajagukguk, J.; Kaewkhao, J.; Djamal, M.; Hidayat, R.; Suprijadi; Ruangtaweep, Y.

    2016-10-01

    Structural and optical properties of Eu3+-doped sodium-lead-zinc-lithium-borate glasses (65-x)B2O3sbnd 15Na2Osbnd 10PbOsbnd 5ZnOsbnd 5Li2Osbnd xEu2O3 (where x = 0, 0.05, 0.1, 0.5, 1.0, 2.0 and 4.0) have been measured and analyzed by varying the Eu3+ ion concentrations. The physical parameters such as polaron radius, field strength and inter nuclear distance have been determined from measurements of densities and refractive indices. The structural properties of the prepared borate glasses were analyzed based on X-ray diffraction (XRD) and FTIR instruments. The diffraction spectra show no characteristic peaks in these glasses, which indicates the amorphous nature of the glasses. The infrared spectrum of the Eu3+-doped sodium-lead-zinc-lithium-borate glass systems show three disparate regions for active absorption band around 830-860 cm-1, 1020-1040 cm-1 and 1170-1180 cm-1. The electronic transitions in the UV-vis and NIR regions are assigned to the 7F0 → 5D4, 7F0 → 5G2, 7F0 → 5L6, 7F0 → 5D3, 7F0 → 5D2, 7F0 → 5D1, 7F0 → 5D07F1 → 5D07F0 → 7F6 and 7F1 → 7F6 levels centered at 362 nm, 380 nm, 395 nm, 414 nm, 465 nm, 533 nm, 583 nm, 590 nm 2092 nm and 2202 nm respectively. Five transition bands of luminescence spectra have been observed by using an excited wavelength of 395 nm. The luminescence intensity ratio (R) of 5D0 → 7F2 (electric dipole) transition to 5D0 → 7F1 (magnetic dipole) transition has been determined to obtain the strength of the covalent/ionic bond between the Eu3+ ions and the surrounding ligands. Radiative life time and emission color of the glasses were estimated and compared with other literature data by varying Eu3+ concentrations. The experimental lifetime of the 5D0 level was found to increase with increasing Eu3+ ion content, suggesting higher non-radiative energy transfer among Eu3+ ions in the glasses.

  7. Characterisation and Optical Studies of Copper Oxide Nanostructures Doped with Lanthanum Ions

    Directory of Open Access Journals (Sweden)

    Varughese G.

    2014-12-01

    Full Text Available Copper Oxide is an extensively studied group II-VI semiconductor with optical properties. It exhibits a wide variety of morphologies in the nano regime that can be grown by tuning the growth habit of the CuO crystal. CuO nano materials with an average particle size of 15-27 nm are synthesized by chemical route. XRD, SEM, FTIR UV-Vis and EDS characterize the samples. The percentage of doping material is confirmed from the EDS spectra. The average crystal size of the prepared CuO: La nanopowder is determined by XRD. The UV absorption spectra revealed the absorption edge at wavelength 389 nm indicating the smaller size of CuO:La nano particle. The optical direct band gap energy of doped CuO nanoparticle is found to be in the range 3.149 eV. The increasing red shift with decreasing particle size suggests that the defects responsible for the intra gap states are primarily surface defect. The La doped CuO is highly effective and can significantly enhance the photo catalytic degradation.

  8. Fabrication tolerances and metrology requirements for ion-exchanged micro-optic lenses: What's good enough?

    Science.gov (United States)

    Messerschmidt, B; Possner, U; Houde-Walter, S N

    1997-11-01

    Allowable deviations in index profiles, dopant distributions, and concentration dependence of diffusion coefficients are determined for collimating microlenses. Examples of high (and low) numerical aperture lenses are given for silver/sodium (and lithium/sodium) ion exchanges. Using the full lens aperture, one can ensure diffraction-limited performance only when the index is measured to within 1.0 x 10(-4) (4.3 x 10(-5)) of the optimum values. Fabrication tolerances for diffraction-limited performance over 80% of the numerical aperture are expressed in terms of the concentration-dependent diffusion coefficient, which typically must be held to within +/-4.7% (+/-11.5%) of ideal values.

  9. Argon Ion Laser Angiosurgery In Different Animal Models Using A Multifiber Optical Delivery System

    Science.gov (United States)

    Kjellstrom, B. Thomas; Bott-Silverman, Corinne; Cothren, Robert M.; Engelmann, Gary L.; Feld, Michael S.; Hayes, Gary B.; Kittrell, Carter; Kramer, John R.

    1988-06-01

    Stenotic or occlusive (two different techniques) lesions were surgically induced in the canine common carotid artery. The lesions were evaluated angiographically prior to as well as after laser angiosurgery (LAS). LAS was performed in 30 dogs using a continuous wave (CW) argon ion laser (Innova 20) coupled to a multifiber, quartz-shielded, fiberoptic catheter. Successful removal of lesion tissue was achieved in 89% of the animals with stenoses and in 40% and 82% in each of the two groups of dogs with occlusions. In the latter two groups, perforation of the vessel wall during LAS was encountered in 60% and 18%, respectively. No perforations occurred in the stenotic animals, where long-term follow-up was possible for up to 60 days with a patency rate of 63% and morphological evidence of excellent healing with complete reendothelialization.

  10. Optical detection of lead and potassium ions using a quantum-dot-based aptamer nanosensor.

    Science.gov (United States)

    Meshik, Xenia; Xu, Ke; Dutta, Mitra; Stroscio, Michael A

    2014-06-01

    Quantum-dot (QD) based nanosensors can be used to detect a wide range of molecules. This study examined a nanosensor comprised of thrombin binding aptamer (TBA) with 700NC InGaP QD on the 5 (') terminus and an Au nanoparticle quencher on the 3 (') terminus. Both K(+) and Pb(2+) bind to TBA, resulting in a conformational change that brings the Au quencher closer to the QD. Photoluminescence measurements indicated a decrease in fluorescence corresponding to an increase in either K(+) or Pb(2+) concentration. For healthy blood serum K(+) concentrations (3.5-5 mM), the beacon exhibited 15-17% quenching efficiency. Pb(2+) concentration of 0.48 μM, the threshold for toxicity in serum, yielded 14% quenching. The beacon's ability to detect changes in ion levels in a critical range of concentrations can make it an effective diagnostic tool.

  11. Optics

    CERN Document Server

    Fincham, W H A

    2013-01-01

    Optics: Eighth Edition covers the work necessary for the specialization in such subjects as ophthalmic optics, optical instruments and lens design. The text includes topics such as the propagation and behavior of light; reflection and refraction - their laws and how different media affect them; lenses - thick and thin, cylindrical and subcylindrical; photometry; dispersion and color; interference; and polarization. Also included are topics such as diffraction and holography; the limitation of beams in optical systems and its effects; and lens systems. The book is recommended for engineering st

  12. Optical characterization of Eu 3+ and Tb 3+ ions doped zinc lead borate glasses

    Science.gov (United States)

    Thulasiramudu, A.; Buddhudu, S.

    2007-02-01

    This paper reports on the spectral analysis of Eu 3+ or Tb 3+ ions (0.5 mol%) doped heavy metal oxide (HMO) based zinc lead borate glasses from the measurement of their absorption, emission spectra and also different physical properties. From the XRD, DSC profiles, the glass nature and glass thermal properties have been studied. The measured emission spectrum of Eu 3+ glass has revealed five transitions ( 5D 0 → 7F 0, 7F 1, 7F 2, 7F 3 and 7F 4) at 578, 591, 613, 654 and 702 nm, respectively, with λexci = 392 nm ( 7F 0 → 5L 6). In the case of Tb 3+:ZLB glass, four emission transitions such as ( 5D 4→ 7F 6, 7F 5, 7F 4 and 7F 3) that are located at 489, 542, 585 and 622 nm, respectively, have been measured with λexci = 374 nm. For all these emission bands decay curves have been plotted to evaluate their lifetimes and the emission processes that arise in the glasses have been explained in terms of energy level schemes.

  13. Thermal and optical properties of Nd{sup 3+} ions in K–Ca–Al fluorophosphate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Linganna, K. [School of Information and Communications, Gwangju Institute of Science and Technology, 261 Cheomdan-gwagiro, Buk-gu, Gwangju 500-712 (Korea, Republic of); Viswanath, C.S. Dwaraka [Department of Physics, Sri Venkateswara University, Tirupati 517502 (India); Narro-Garcia, R. [Centro de Física Aplicada y Tecnología Avanzada, Universidad Nacional Autónoma de México, Boulevard Juriquilla 3001, Querétaro 76230, Querétaro Mexico (Mexico); Ju, S.; Han, W.-T. [School of Information and Communications, Gwangju Institute of Science and Technology, 261 Cheomdan-gwagiro, Buk-gu, Gwangju 500-712 (Korea, Republic of); Jayasankar, C.K. [Department of Physics, Sri Venkateswara University, Tirupati 517502 (India); Venkatramu, V., E-mail: vvramuphd@gmail.com [Department of Physics, Yogi Vemana University, Kadapa 516003, Andhra Pradesh (India)

    2015-10-15

    Fluorophosphate glasses of composition (P{sub 2}O{sub 5}–K{sub 2}O–Al{sub 2}O{sub 3}–CaO–CaF{sub 2})-doped with various Nd{sub 2}O{sub 3} concentrations were prepared by a melt quenching technique and their thermal, vibrational and optical properties were investigated. Thermal stability of the fluorophosphate glass has been determined from differential scanning calorimetric thermograph. The vibrational modes of the present glass have been studied using Raman spectrum. The intensity parameters, Ω{sub λ} (λ=2, 4 and 6) as well as radiative properties for the {sup 4}F{sub 3/2} level of Nd{sup 3+} ion, have been evaluated from the absorption spectra of 1.0 mol% Nd{sub 2}O{sub 3}-doped glass using the Judd–Ofelt theory. Strong near infrared emission at 1.06 =m attributed to {sup 4}F{sub 3/2}→{sup 4}I{sub 11/2} transition has been obtained for all the glasses upon 806 nm diode laser excitation. Decay analysis has been carried out and found that the lifetime for the {sup 4}F{sub 3/2} level of Nd{sup 3+} ion was found to be higher compared to the other Nd{sup 3+}-doped glass host matrices. The quantum efficiency and saturation intensity have been determined to be 93% and 2.32×10{sup 8} W/m{sup 2}, respectively for 1.0 mol% Nd{sub 2}O{sub 3}-doped glass. The results indicate that the present glasses could be useful for 1.06 µm laser applications. - Highlights: • Nd{sup 3+}-doped K–Al–Ca fluorophosphate glasses were prepared and characterized. • Raman and DSC measurements have been carried out. • Strong near infrared emission at 1.06 μm ({sup 4}F{sub 3/2}→{sup 4}I{sub 11/2} transition) has been found. • Optical properties have been evaluated and compared to other host matrices. • Higher lifetime and quantum efficiency have been noticed in the studied glasses.

  14. New developments for the analysis of archaeological and artistic artifacts by optical and ion beam methods at LAMFI

    Energy Technology Data Exchange (ETDEWEB)

    Rizzutto, Marcia A.; Tabacniks, Manfredo H.; Barbosa, Marcel D. L.; Added, Nemitala; Curado, Jessica F.; Kajiya, Elizabet M.; Campos, Pedro H.O.V. de [Universidade de Sao Paulo (USP), SP (Brazil). Inst. de Fisica

    2011-07-01

    Full text: Since 2005, the analysis of artistic and cultural heritage objects at LAMFI-USP (Laboratorio de Analises de Materiais com Feixes Ionicos), initially restricted to ion beam methods, is growing steadily. Since then, alternative methodologies and procedures have been incorporated to better characterize these objects, that possess distinctive physical characteristics and also due to their high cultural and monetary value. The examinations were expanded to other non-destructive analytical techniques like portable XRF (X-ray fluorescence) analysis, X-ray radiography, visible, UV (ultraviolet) and IR (infrared) light imaging that are helping to better understand these art objects, particularly paintings, where the techniques are helping to access the conservation state and also reveal underlying drawings, which help understanding the creative process of the artist. The external beam arrangement at LAMFI was recently updated for simultaneous PIXE (Particle induced X-ray emission), RBS (Rutherford back scattering), PIGE (Particle induced gamma-ray emission) and IBL (Ion beam luminescence) analysis in open air. The new setup comprises a 2 {pi} star-like detector assembly with 7 collimated telescopes: two openings have laser beams for optical alignment of the target, 2 are used for X-ray detectors, 1 for a particle detector, 1 for an optical spectrometer, and 1 for a image. The particle and X-ray detector telescopes can be evacuated to reduce signal losses. The 2 telescopes with the X-ray detectors have absorbers to selectively filter low energy X-rays, optimizing the PIXE detection limits. The beam exit window is made of an 8 {mu}m aluminum foil to monitoring integrated beam charge by measuring the Al gamma rays with a NaI detector. The geometry and materials of the assembly have been carefully designed to shield the X-ray detectors from measuring the X-rays from the exit beam window as well as reducing the detection of Ar K {alpha} from the in air beam path. The

  15. The role of Sm ions in optical storage of SrS

    Institute of Scientific and Technical Information of China (English)

    HE; Zhiyi

    2001-01-01

    ., Wampler, E. J., Gaskell, C. M., Emission-line properties of optically and radio-selected complete quasars samples, Astrophys. J., 1989, 338: 630.[13]Yong, P., Sargent, W. L. W. A., High-resolution study of the absorption spectra of three QSOs: evidence for cosmological evolution in the lyman-alpha lines, Astrophys. J., 1982, 252: 10.[14]Lawrence, J., Zucker, J. R., Readhead, A. C. S. et al., Optical spectra of a complete sample of radio sources I. The spectra, Astrophys. J. Suppl., 1996, 107: 541.[15]Junkkarinen, V. T. , Burbidge E. M. , Smith, H. E. , Spectrophyotometry of six broad absoption line QSOs, Astrophys. J. ,1987, 317, 460.[16]Laor, A., Babcall, J. N., Jannuzi, B. T. et al., The ultraviolet emission properties of 13 quasars, Astrophys. J. Suppl.,1995, 99: 1.[17]Baldwin, J. A., Rees, M. J., Longair, M. S. et al., QSOs with narrow emission lines, Astrophys. J., 1988, 327: 103.[18]Shaver, P. A. , Boksenberg A. , Robertson, J. G. , Spectroscopy of the QSO pair Q0028 + 003/Q0029 + 003, Astrophys.J., 1982, 261: L7.[19]Baldwin, J. A., Netzer, H., The emission-line regions of high-redshift QSOs, Astrophys. J., 1978, 226: 1.[20]Wills, B. J., Thompson, K. L., Han, M. et al. , The Hubble space telescope sample of radio-loud quasars: Ultraviolet spectra of the first 31 quasars, Astrophys. J., 1995, 447: 139.[21]Osmer, P. S., Smith, M. G. , Discovery and spectroscopic observations of 27 optical selected quasars with 1.4 < z < 2.5,Astrophys. J., 1977, 213: 607.[22]Storrie-Lombardi, L. J., McMabon, R. G., Irwin, M. J. et al., APM Z > = 4 QSO Survey: Spectra and Intervening Ab-sorption Systems, Astrophys. J., 1996, 468: 121.[23]Young, P. , Sargent, W. L. W. , Boksenberg, A. , Clv absorption in an unbiased sample of 33 QSOs: evidence for the inter-vening galaxy hypothesis, Astrophys. J. Suppl., 1982, 48: 455.[24]Zitelli, V., Mignoli, M., Zarano, B. et al., A spectroscopically complete sample of quasars with Bj ≤ 22

  16. Optical absorption and near infrared emission properties of Nd 3+ ions in alkali lead tellurofluoroborate glasses

    Science.gov (United States)

    Saleem, S. A.; Jamalaiah, B. C.; Kumar, J. Suresh; Babu, A. Mohan; Moorthy, L. Rama; Jayasimhadri, M.; Jang, Kiwan; Lee, Ho Sueb; Yi, Soung Soo; Jeong, Jung Hyun

    2009-12-01

    Nd 3+ doped H 3BO 3-PbO-TeO 2-RF (R = Li, Na and K) glasses were prepared through melt quenching technique. Optical absorption and near infrared (NIR) fluorescence spectra were recorded at room temperature. The spectral intensities were analyzed in terms of the Judd-Ofelt (J-O) parameters ( Ω λ = 2, 4, 6). The covalency effect of Nd-O bond on the J-O parameters was estimated from the relative absorbance ratio (R) between 4I 9/2 → 4F 7/2 and 4I 9/2 → 4S 3/2 transitions. The effect of Nd-O covalency on the Ω4 and Ω6 intensity parameters as well as on the spontaneous emission probabilities ( AR) was discussed. Lomheim and Shazer hybrid method was applied to determine the fluorescence branching ratios ( βR) of each emission transition from the 4F 3/2 metastable level to its lower lying levels. The evaluated total radiative transition probabilities ( AT), stimulated emission cross-sections ( σe) and gain bandwidth parameters ( σe × Δ λP) were compared with the earlier reports.

  17. Link between optical spectra, crystal-field parameters, and local environments of Eu3+ ions in Eu2O3-doped sodium disilicate glass

    Science.gov (United States)

    Qin, T.; Mountjoy, G.; Afify, N. D.; Reid, M. F.; Yeung, Y. Y.; Speghini, A.; Bettinelli, M.

    2011-09-01

    Rare-earth-doped glasses are key materials for optical technology due to the luminescent properties of 4fn ions. The crystal-field model describes the effect of local environment on transitions between 4f electrons. We present a detailed modeling study of the optical spectra of sodium disilicate glass, 33Na2O·67SiO2, doped with 0.2% and 1.0 mol% Eu2O3. This study uses very large molecular dynamics models with up to 100 Eu3+ ions, the superposition model for covalent and overlap effects on crystal-field parameters, and realistic values for homogeneous linewidth broadening. The simulated spectra are in reasonable agreement with experiment. The trends in 7FJ energy levels across different Eu3+ ion sites have been examined and a very detailed analysis is presented that looks at how features of the spectra are related to features of the local environment of Eu3+ ions. Increasing the crystal-field strength Stotal causes the 7F0 energy level to decrease and causes the splitting of 7FJ manifolds to increase, and this is due to increasing mixing of 4f wave functions. To a reasonable approximation the crystal-field strength components Sk depend on angular positions of ligands independently of distances to ligands. The former are seen to be more significant in determining Sk, which are closely related to the rotationally invariant bond-orientational order parameters Qk. The values of S2 are approximately linear in Q2, and the values of Q2 are higher for fivefold than sixfold coordinated rare-earth ions. These results can be of importance for efforts to enhance the local environment of rare-earth ions in oxide glasses for optical applications.

  18. Molecular terms, magnetic moments, and optical transitions of molecular ions C60mplus-or-minus

    Science.gov (United States)

    Nikolaev, A. V.; Michel, K. H.

    2002-09-01

    Starting from a multipole expansion of intramolecular Coulomb interactions, we present configuration interaction calculations of the molecular energy terms of the hole configurations (hu)+m, m=2-5, of C60m+ cations, of the electron configurations t1un, n=2-4, of the C60n- anions, and of the exciton configurations (hu+t1u)-, (hu+t1g)- of the neutral C60 molecule. The ground state of C602- is either 3T1g or 1Ag, depending on the energy separation between t1g and t1u levels. There are three close (approx0.03 eV) low lying spin triplets 3T1g, 3Gg, 3T2g for C602+, and three spin quartets 4T1u, 4Gu, 4T2u for C603+, which can be subjected to the Jahn-Teller effect. The number of low lying nearly degenerate states is largest for m=3 holes. We have calculated the magnetic moments of the hole and electron configurations and found that they are independent of molecular orientation with respect to an external magnetic field. The coupling of spin and orbital momenta differs from the atomic case. We analyze the electronic dipolar transitions (t1u)2[right arrow] t1ut1g and (t1u)3 [right arrow](t1u)2t1g for C602- and C603-. Three optical absorption lines (3T1g[right arrow] 3Hu, 3T1u, 3Au) are found for the ground level of C602- and only one line (4Au[right arrow]4T1g) for the ground state of C603-. We compare our results with the experimental data for C60n- in solutions and with earlier theoretical studies.

  19. Modification of the optical and structural properties of ZnO nanowires by low-energy Ar+ ion sputtering

    Science.gov (United States)

    Allah, Rabie Fath; Ben, Teresa; González, David; Hortelano, Vanesa; Martínez, Oscar; Plaza, Jose Luis

    2013-04-01

    The effects of low-energy (≤2 kV) Ar+ irradiation on the optical and structural properties of zinc oxide (ZnO) nanowires (NWs) grown by a simple and cost-effective low-temperature technique were investigated. Both photoluminescence spectra from ZnO NW-coated films and cathodoluminescence analysis of individual ZnO NWs demonstrated obvious evidences of ultraviolet/visible luminescent enhancement with respect to irradiation fluence. Annihilation of the thinner ZnO NWs after the ion bombardment was appreciated by means of high-resolution scanning electron microscopy and transmission electron microscopy (TEM), which results in an increasing NW mean diameter for increasing irradiation fluences. Corresponding structural analysis by TEM pointed out not only significant changes in the morphology but also in the microstructure of these NWs, revealing certain radiation-sensitive behavior. The possible mechanisms accounting for the decrease of the deep-level emissions in the NWs with the increasing irradiation fluences are discussed according to their structural modifications.

  20. The structural changes and optical properties of LiNbO3 after Er implantation using high ion fluencies

    Science.gov (United States)

    Macková, A.; Malinský, P.; Pupíková, H.; Nekvindová, P.; Cajzl, J.; Sofer, Z.; Wilhelm, R. A.; Kolitsch, A.; Oswald, J.

    2014-08-01

    The structural and compositional changes of LiNbO3 implanted with 190 keV Er+ ions into various crystallographic cuts with fluencies of 1 × 1016 and 5 × 1016 cm-2 were studied. The effect of post-implantation annealing at 1000 °C in oxygen atmosphere was also examined. Concentration depth profiles of implanted erbium, determined by Rutherford Backscattering Spectrometry (RBS), are broader than those from the SRIM simulation. The maximum erbium concentration (of up to 8 at.%) is observed at the depth of about 50 nm, for all crystal cuts. The structure of the implanted layers were characterised by RBS-channelling method. The lower relative number of disordered atoms in the crystalline matrix was observed in the lithium niobate (LN) implanted at a fluence of 1 × 1016 cm-2, where also the preferential position of the erbium in substitutional sites was observed when compared to the randomly distributed erbium in interstitial positions at a fluence of 5 × 1016 cm-2 after the annealing. Surface-morphology changes at the highest implantation fluencies were studied using Atomic Force Microscopy (AFM). Since we were interested in the relation between the structural changes and optical properties, erbium luminescence properties were measured in the region of 1440-1650 nm. The positive effect of post-implantation annealing on the luminescence properties caused by structural recovery was proved.

  1. Optical properties and size distribution of the nanocolloids made of rare-earth ion-doped NaYF4

    Science.gov (United States)

    Patel, Darayas N.; Lewis, Ashley; Wright, Donald M.; Lewis, Danielle; Valentine, Rueben; Valentine, Maucus; Wessley, Dennis; Sarkisov, Sergey; Darwish, Abdalla M.

    2015-03-01

    In this paper we investigate optical properties and size distribution of the nano-colloids made of trivalent rare-earth ion doped fluorides: holmium and ytterbium, thulium and ytterbium, and erbium and ytterbium co-doped NaYF4. These materials were synthesized by using simple co-precipitation synthetic method. The initially prepared micro-crystals had very weak or no visible upconversion fluorescence signals when being pumped with a 980-nm laser. The fluorescence intensity significantly increased after the crystals were annealed at a temperature of 400°C - 600°C undergoing the transition from cubic alpha to hexagonal beta phase of the fluoride host. Nano-colloids of the crystals were made in polar solvents using the laser ablation and ball milling methods. Size analyses of the prepared nano-colloids were conducted using a dynamic light scatterometer and atomic force microscope. The nano-colloids were filled in holey PCFs and their fluorescent properties were studied and the feasibility of new a type of fiber amplifier/laser was evaluated.

  2. Optical properties of ion-doped ZnO(Se) layers in the context of band anticrossing theory

    Energy Technology Data Exchange (ETDEWEB)

    Morozova, N. K., E-mail: MorozovaNK@mail.ru [National Research University “Moscow Power Engineering Institute” (Russian Federation); Galstyan, V. G. [Russian Academy of Sciences, Shubnikov Institute of Crystallography (Russian Federation); Volkov, A. O. [National Research University “Moscow Power Engineering Institute” (Russian Federation); Mashchenko, V. E. [Russian Academy of Sciences, Frumkin Institute of Physical Chemistry and Electrochemistry (Russian Federation)

    2015-09-15

    The study of the optical properties of ZnO(Se) is a continuation of previous studies of ZnS(O), ZnSe(O), and CdS(O) systems in the context of band anticrossing theory. Selenium ions are implanted into high-purity zinc oxide crystals to a concentration of 10{sup 20} cm{sup –3}. The microcathodoluminescence spectra recorded with a scanning electron microscope at a temperature of 100 K provide information from the bulk of the implanted layer. The origin of the orange-red luminescence of ZnO(Se)–Zn layers is clarified. Orangered luminescence is thought to be a result of the formation of a highly mismatched alloy system, in which ZnSe(O) is formed during implantation and radiation annealing. Data suggesting that the green luminescence of pure self-activated ZnO–Zn is the self-activated (SA) emission studied in detail for other II–VI compounds (ZnS(O), ZnSe(O)) and defined by intrinsic defect complexes (A centers) are reported.

  3. Mathematical modeling and application of removal functions during deterministic ion beam figuring of optical surfaces. Part 2: application.

    Science.gov (United States)

    Liao, Wenlin; Dai, Yifan; Xie, Xuhui; Zhou, Lin

    2014-07-01

    Ion beam figuring (IBF) is established for the final precision figuring of optical components. In this deterministic method, the figuring process is represented by a two-dimensional (2D) convolution operation of a constant removal function and the dwell time, where the figuring precision is guaranteed by the stability of the removal function as well as the solution accuracy of the dwell time. However, the current 2D convolution equation cannot factually reflect the IBF process of curved surfaces, which neglects the influence of the projection distortion and the workpiece geometry. Consequently, the current convolution algorithm for the IBF process would influence the solution accuracy for the dwell time and reduce the convergence of the figuring process. In this part, we propose an improved algorithm based on the mathematical modeling of the dynamic removal function in Part A, which provides a more accurate dwell time for IBF of a curved surface. Additionally, simulation analysis and figuring experiments are carried out to verify the feasibility of our proposed algorithm. The final experimental results indicate that the figuring precision and efficiency can be simultaneously improved by this method.

  4. Mathematical modeling and application of removal functions during deterministic ion beam figuring of optical surfaces. Part 1: Mathematical modeling.

    Science.gov (United States)

    Liao, Wenlin; Dai, Yifan; Xie, Xuhui; Zhou, Lin

    2014-07-01

    Ion beam figuring (IBF) is established for the final precision figuring of high-performance optical components, where the figuring accuracy is guaranteed by the stability of the removal function and the solution accuracy of the dwell time. In this deterministic method, the figuring process can be represented by a two-dimensional (2D) convolution operation of a constant removal function and the dwell time. However, we have found that the current 2D convolution operation cannot factually describe the IBF process of curved surfaces, which neglects the influences of the projection distortion and the workpiece geometry on the removal function. Consequently, the current 2D convolution algorithm would influence the solution accuracy for the dwell time and reduce the convergence of the figuring process. In this part, based on the material removal characteristics of IBF, a mathematical model of the removal function is developed theoretically and verified experimentally. Research results show that the removal function during IBF of a curved surface is actually a dynamic function in the 2D convolution algorithm. The mathematical modeling of the dynamic removal function provides theoretical foundations for our proposed new algorithm in the next part, and final verification experiments indicate that this algorithm can effectively improve the accuracy of the dwell time solution for the IBF of curved surfaces.

  5. Analysis of a photon number resolving detector based on fluorescence readout of an ion Coulomb crystal quantum memory inside an optical cavity

    DEFF Research Database (Denmark)

    Clausen, Christoph; Sangouard, N.; Drewsen, M.

    2013-01-01

    The ability to detect single photons with a high efficiency is a crucial requirement for various quantum information applications. By combining the storage process of a quantum memory for photons with fluorescence-based quantum state measurement, it is, in principle, possible to achieve high...... on an ion Coulomb crystal inside a moderately high-finesse optical cavity. The cavity enhancement leads to an effective optical depth of 15 for a finesse of 3000 with only about 1500 ions interacting with the light field. We show that these values allow for essentially noiseless detection with an efficiency......-efficiency photon counting in large ensembles of atoms. The large number of atoms can, however, pose significant problems in terms of noise stemming from imperfect initial state preparation and off-resonant fluorescence. We identify and analyse a concrete implementation of a photon number resolving detector based...

  6. Laser-Induced Forward Transfer-printing of focused ion beam pre-machined crystalline magneto-optic yttrium iron garnet micro-discs.

    Science.gov (United States)

    Sones, C L; Feinaeugle, M; Sposito, A; Gholipour, B; Eason, R W

    2012-07-02

    We present femtosecond laser-induced forward transfer of focused ion beam pre-machined discs of crystalline magneto-optic yttrium iron garnet (YIG) films. Debris-free circular micro-discs with smooth edges and surface uniformity have been successfully printed. The crystalline nature of the printed micro-discs has not been altered by the LIFT printing process, as was confirmed via micro-Raman measurements.

  7. Sm3+-doped fluorophosphate glass: Formation of Ag nanoparticles via Ag+/K+ ion exchange and their effects on optical and dielectric properties

    Science.gov (United States)

    Thomas, Sunil; Sajna, M. S.; Nayab Rasool, Sk.; Gopinath, Manju; Joseph, Cyriac; Unnikrishnan, N. V.

    2015-01-01

    Silver-potassium ion exchange on Sm3+-doped fluorophosphate glass has been carried out via thermal diffusion method. The crystallite size of silver was estimated to be 19 nm from X-ray diffraction pattern and it was confirmed using transmission electron microscopy analysis. Assessment of the optical properties has been carried out by absorption, photoluminescence and lifetime measurements. Present glass system exhibits favorable optical properties for possible uses as optical amplifiers, sensors and planar waveguides. The energy transfer mechanism from silver to samarium and the surface plasmon resonance of silver nanoparticles are discussed for the ion exchanged glass. The dielectric studies have been carried out in order to assess the influence of silver on the dielectric properties and ac conductivity of the ion exchanged glass. Coulomb blockade effects have been discussed to clarify the enhancement in the insulating behavior of the glass by the incorporation of silver nanoparticles. The power-law and Cole-Cole parameters were determined and the influence of silver on these parameters is discussed.

  8. Surface hardening of ZnSe, ZnS, and ZnS/ZnSe optical materials by implantation of 1 MeV hydrogen ions

    Science.gov (United States)

    Wu, Richard L. C.; McCormick, A. W.; Pronko, P. P.; Keeley, Joseph

    1991-07-01

    Zinc selenide and zinc sulfide are excellent optical materials for applications in the visible and infrared regions of the spectrum. Since these materials possess low mechanical strength and toughness, they are vulnerable to erosion and impact damage in severe environments. In order to improve their physical hardness without degrading their spectral transmission, high-energy (1 MeV) hydrogen ions were implanted into the surfaces of ZnSe, water-clear ZnS (Cleartran TM), and ZnS/ZnSe composite (Tuftran TM. A systematic study of the effect of ion fluence (0.1 to 3 × 10 17/cm 2) on surface hardness and optical transmission was performed. Substantial improvement in microhardness has been found which increases with dosage. The hardness of Tuftran TM leveled off at a dose of 3 × 10 16/cm 2, while that of ZnSe and Cleartran TM continued to improve with ion fluence. The hardness of ZnSe was increased by a factor of 78% at a dose of 3 × 10 17/cm 2, without degrading important optical properties.

  9. Effect of Ar+ ion post-irradiation on crystal structure, magnetic behavior and optical band gap of Co-implanted ZnO wafers

    Science.gov (United States)

    Xu, N. N.; Li, G. P.; Lin, Q. L.; Liu, H.; Bao, L. M.

    2016-12-01

    Single crystals wurtzite ZnO with (001) orientation were implanted with Co+ ions at room temperature (RT). To tune their magnetic behavior as well as the band gap of the implanted wafers, Ar+ ion post-irradiation (PI) was performed using the calculated energy and ion dose. The formed Co clusters present in the high dose Co-implanted ZnO wafer were observed to be absent after the PI, which is quite different from the low dose doped one. It is found that all the implanted samples showed a giant magnetic moment and a narrowing optical band gap, and that the post-irradiated ones exhibited an even further redshifted absorption edge and ferromagnetic behavior but with saturation magnetization (MS) drastically decreased.

  10. Theoretical investigations of the optical and EPR spectra for trivalent cerium and ytterbium ions in orthorhombic YF{sub 3} crystal

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Hong-Gang, E-mail: kezhouliu@163.com; Zheng, Wen-Chen

    2016-09-01

    The optical spectra and electron paramagnetic resonance (EPR) parameters (g factors and hyperfine structure constants A) for trivalent cerium and ytterbium ions in YF{sub 3} crystal with orthorhombic structure are investigated together by the complete diagonalization (of energy matrix) method (CDM). The obtained results are in reasonable agreement with the experimental ones. More importantly, two magnetically nonequivalent centers in YF{sub 3} crystal observed in EPR experiments are confirmed and ascribed to their specific positions in a unit cell by our calculations based on superposition model (SPM) analysis. Such identification of local sites with different magnetic properties would help us to understand not only the EPR spectra and magnetic susceptibility of other lanthanide ions doped in crystals with the same structure as YF{sub 3} but also the energy transfer scheme between two lanthanide ions occupying such two sites. All results are discussed carefully.

  11. Evaluation of trap-induced systematic frequency shifts for a multi-ion optical clock at the $10^{-19}$ level

    CERN Document Server

    Keller, J; Kalincev, D; Kiethe, J; Mehlstäubler, T E

    2015-01-01

    In order to improve the short-term stability of trapped-ion optical clocks, we are developing a frequency standard based on ${}^{115}$In${}^+$ / ${}^{172}$Yb${}^+$ Coulomb crystals. For this purpose, we have developed scalable segmented Paul traps which allow a high level of control for multiple ion ensembles. In this article, we detail on our recent results regarding the reduction of the leading sources of frequency uncertainty introduced by the ion trap: 2nd-order Doppler shifts due to micromotion and the heating of secular motion, as well as the black-body radiation shift due to warming of the trap. We show that the fractional frequency uncertainty due to each of these effects can be reduced to well below $10^{-19}$.

  12. Modifications induced in the structural and optical properties of bismuth sodium borosilicate glass thin films by 120 MeV Ag{sup 7+} ions

    Energy Technology Data Exchange (ETDEWEB)

    Kaur, Ravneet, E-mail: ravneet_383@yahoo.com [Department of Physics, Guru Nanak Dev University, Amritsar 143 005 (India); Singh, Surinder [Department of Physics, Guru Nanak Dev University, Amritsar 143 005 (India); Pandey, O.P. [School of Physics and Materials Science, Thapar University, Patiala 147 004 (India)

    2013-06-15

    The composition of the glass is Bi{sub 2}O{sub 3} (20%)–Na{sub 2}O (15%)–B{sub 2}O{sub 3} (50%)–SiO{sub 2} (15%) was prepared by conventional melt quench method. To study the effect of heavy ion irradiation on the glass network and structural units, thin films of the glass have been prepared by electron beam gun evaporation. The prepared films are irradiated using 120 MeV Ag{sup 7+} ions in the fluence range of 1 × 10{sup 12}–3 × 10{sup 13} ions cm{sup −2}. The optical and structural properties were investigated using UV–visible absorption spectroscopy and Fourier Transform Infrared (FTIR) spectroscopic techniques. A significant decrease in the band gap is observed after irradiation which is indicative of the fact that radiation has caused compaction in the glass structure.

  13. Characterization of laser-produced plasma ions of various metals and their effect on the optical properties of the CR-39 polymer

    Science.gov (United States)

    Ali, Dilawar; Butt, M. Z.; Naseem, S.

    2013-01-01

    The laser-produced plasma (LPP) ions of various metals (Mo, Ni, Cu, Ti and Zn) was implanted in CR-39 polymer, and their influence on its optical properties was investigated. The plasma of these metals was produced using 200 shots of a Q-switched Nd:YAG pulsed laser in a vacuum of 10-3 Torr. The CR-39 specimens were exposed to LPP ions (flux: F=8.01×109-22.14×109 ions/m2, average energy: E av=52-297 keV) emitted along the normal to the metal surface in each case. Both F and E av were found to be a function of the room temperature Debye-Waller thermal parameter B and increase with increase in B-value. The structural behavior of virgin and implanted specimens was investigated using a ultra violet (UV)-visible spectrophotometer. The value of disorder content (Urbach energy E u) was found to lie in the range of 0.287-0.377 eV. The optical band gap energy (E g) for indirect transition decreased on implantation with metallic LPP ions, whereas such a variation in the case of direct transition was negligible. It was observed that E g for indirect transition increases with the increase in E u, whereas the dependence of E g for direct transition on E u was negligible.

  14. Effect of irradiation by 140 Mev Ag{sup 11+} ions on the optical and electrical properties of polypropylene/TiO{sub 2} composite

    Energy Technology Data Exchange (ETDEWEB)

    Qureshi, Anjum [Department of Physics, M.S. University of Baroda, Vadodara 390002 (India); Department of Metallurgical and Materials Engineering, Marmara University, 81040 Istanbul (Turkey); Singh, Dolly [Department of Physics, M.S. University of Baroda, Vadodara 390002 (India); Singh, N.L., E-mail: singhnl_msu@yahoo.co [Department of Physics, M.S. University of Baroda, Vadodara 390002 (India); Ataoglu, S. [Department of Civil Engineering, Istanbul Technical University, Maslak, 34469 Istanbul (Turkey); Gulluoglu, Arif N. [Department of Metallurgical and Materials Engineering, Marmara University, 81040 Istanbul (Turkey); Tripathi, Ambuj; Avasthi, D.K. [Inter University Accelerator Centre, Aruna Asaf Ali Marg, 110067 New Delhi (India)

    2009-10-15

    Changes in the optical, structural, dielectric properties and surface morphology of a polypropylene/TiO{sub 2} composite due to swift heavy ion irradiation were studied by means of UV-visible spectroscopy, X-ray diffraction, impedance gain phase analyzer and atomic force microscopy. Samples were irradiated with 140 MeV Ag{sup 11+} ions at fluences of 1 x 10{sup 11} and 5 x 10{sup 12} ions/cm{sup 2}. UV-visible absorption analysis reveals a decrease in optical direct band gap from 2.62 to 2.42 eV after a fluence of 5 x 10{sup 12} ions/cm{sup 2}. X-ray diffractograms show an increase in crystallinity of the composite due to irradiation. The dielectric constants obey the Universal law given by epsilonalphaf{sup n-1}, where n varies from 0.38 to 0.91. The dielectric constant and loss are observed to change significantly due to irradiation. Cole-cole diagrams have shown the frequency dependence of the complex impedance at different fluences. The average surface roughness of the composite decreases upon irradiation.

  15. Radiation synthesized poly(n-vinyl-2-pyrrolidone)-stabilized-gold nanoparticles as LSPR-based optical sensor for mercury ions estimation

    Energy Technology Data Exchange (ETDEWEB)

    Misra, Nilanjal; Kumar, Virendra, E-mail: vkrawat75@gmail.com, E-mail: vkumar@barc.gov.in; Goel, Narender Kumar; Varshney, Lalit [Bhabha Atomic Research Centre, Radiation Technology Development Division (India)

    2015-07-15

    Poly(n-vinyl-2-pyrrolidone)-stabilized-gold nanoparticles (PVP-Au-NPs) have been synthesized via a green-{sup 60}Co-Gamma radiolytic route and employed as a localized surface plasmon resonance (LSPR)-based optical sensor for estimation of trace quantities of Hg{sup 2+} ion in aqueous solutions. The in situ generated PVP-Au-NPs were characterized using UV–vis spectroscopy, transmission electron microscopy, and particle size analysis techniques. Reaction conditions were optimized to obtain uniformly dispersed PVP-Au-NPs with average particle size of 7.1 ± 1.6 nm (±s), which exhibited a narrow LSPR band at ∼527 nm. The decrease in LSPR band intensity of PVP-Au-NPs with increase in Hg{sup 2+} ion concentration was found to be linear in the Hg{sup 2+} ion concentration range of 0–100 nM. The LSPR-based PVP-Au-NPs optical sensor system was found to be selective for Hg{sup 2+} and independent of interference from other metal ions such as Ca{sup 2+,} Cu{sup 2+}, Cd{sup 2+}, and Fe{sup 2+} up to a concentration of 500 nM.

  16. Synthesis and optical absorption properties of TiO2 nanostructures in SiO2 by sequential implantation of Cu and Ti ions

    Science.gov (United States)

    Jing, Yaqi; Mu, Xiaoyu; Liu, Xiaoyu; Liu, Changlong

    2017-09-01

    Optical-grade silica samples were singly or sequentially implanted with 100 keV Cu and 40 keV Ti ions at the same fluence of 1 × 1017 ions/cm2, and were then subjected to furnace annealing in nitrogen ambient. Structure, spatial distribution as well as optical absorption properties of the synthesized nanostructures have been investigated in detail by using various techniques. Our results clearly show that high fluence Ti ion implantation together with subsequent annealing at high temperature could lead to formation of TiO2 nanoparticles with both rutile and anatase phases in SiO2 substrate, which causes an absorption band edge at about 365 nm. The pre-implantation of Cu ion could not only largely enhance growth of the TiO2 nanoparticles during annealing, but also significantly reduce the corresponding band gap energy. Moreover, results from cross sectional transmission electron microscopy measurements demonstrate that the pre-implanted Cu atoms participates into the thermal growth of the TiO2 nanoparticles, which may be responsible for the large redshift of the absorption behavior obtained in the Cu and Ti sequentially implanted SiO2.

  17. Synthesis, crystal growth, structural, spectral, thermal, mechanical, linear and nonlinear optical studies of organic single crystal 4-Iodo 4-nitrostilbene (IONS): A potential NLO material

    Energy Technology Data Exchange (ETDEWEB)

    Dinakaran, Paul M.; Kalainathan, S., E-mail: kalainathan@yahoo.com

    2013-12-16

    An organic nonlinear optical material 4-Iodo 4-nitrostilbene (IONS) has been synthesized and good optical quality single crystal was grown from ethyl methyl ketone solvent by the solution growth technique. Single and powder X-ray diffraction analyses reveals that the grown crystal belongs to monoclinic crystal system with noncentrosymmetric space group ‘P2{sub 1}’ and it has good crystalline nature. Functional groups and molecular structure of the title compound were confirmed by FTIR and {sup 1}H NMR respectively. The UV–Vis–NIR absorption study reveals no absorption in the visible region and the cut-off wavelength was found to be at 412.84 nm, TG/DTA, mass spectral analysis, photoluminescence and microhardness studies have been carried out for the grown crystals and results are discussed in detail. The second harmonic efficiency of the IONS was determined by Kurtz–Perry powder technique which reveals that the IONS crystal (3.1 V) has greater efficiency i.e., 143 times to that of KDP (21.7 mV). - Highlights: • The 4-Iodo 4-nitrostilbene (IONS) material has been synthesized by Wittig reaction. • The single crystal was grown for the first time with dimensions of 9.5 × 4 × 1.5 mm{sup 3}. • SHG efficiency of IONS is 143 times greater than that of KDP crystal. • The UV–Vis absorption study reveals that the transparency was found to be good. • IONS crystal is a potential candidate for optoelectronic applications.

  18. Highly selective and sensitive optical sensor for determination of Pb2+and Hg2+ ions based on the covalent immobilization of dithizone on agarose membrane

    Science.gov (United States)

    Zargoosh, Kiomars; Babadi, Fatemeh Farhadian

    2015-02-01

    A highly sensitive and selective optical membrane for determination of Hg2+ and Pb2+ was prepared by covalent immobilization of dithizone on agarose membrane. In addition to its high stability, reproducibility and relatively long lifetime, the proposed optical sensor revealed good selectivity for target ions over a large number of alkali, alkaline earth, transition, and heavy metal ions. The proposed optical membrane displays linear responses from 1.1 × 10-8 to 2.0 × 10-6 mol L-1 and 1.2 × 10-8 to 2.4 × 10-6 mol L-1 for Hg2+ and Pb2+, respectively. The limits of detection (LOD) were 2.0 × 10-9 mol L-1 and 4.0 × 10-9 mol L-1 for Hg2+ and Pb2, respectively. The prepared optical membrane was successfully applied to the determination of Hg2+ and Pb2+ in industrial wastes, spiked tap water and natural waters without any preconcentration step.

  19. Development of an optical thermal history coating sensor based on the oxidation of a divalent rare earth ion phosphor

    Science.gov (United States)

    Yáñez-González, Álvaro; Ruiz-Trejo, Enrique; van Wachem, Berend; Skinner, Stephen; Beyrau, Frank; Heyes, Andrew

    2016-11-01

    The measurement of temperatures in gas turbines, boilers, heat exchangers and other components exposed to hot gases is essential to design energy efficient systems and improve maintenance procedures. When on-line measurements, such as those performed with thermocouples and pyrometers, are not possible or inconvenient, the maximum temperatures of operation can be recorded and measured off-line after operation. Although thermal paints have been used for many years for this purpose, a novel technique based on irreversible changes in the optical properties of thermographic phosphors, can overcome some of the disadvantages of previous methods. In particular, oxidation of the divalent rare earth ion phosphor BaMgAl10O17:Eu (BAM:Eu) has shown great potential for temperature sensing between 700 °C and 1200 °C. The emission spectra of this phosphor change with temperature, which permits to define an intensity ratio between different lines in the spectra that can be used as a measurand of the temperature. In this paper, the study of the sensing capabilities of a sensor coating based on BAM:Eu phosphor material is addressed for the first time. The sensitivity of the intensity ratio is investigated in the temperature range from 800 °C to 1100 °C, and is proved to be affected by ionic diffusion of transition metals from the substrate. The use of an interlayer made of zirconia proves efficient in reducing ionic diffusion and coatings with this diffusion barrier present sensitivity comparable to that of the powder material.

  20. Modeling of optical amplifier waveguide based on silicon nanostructures and rare earth ions doped silica matrix gain media by a finite-difference time-domain method: comparison of achievable gain with Er3+ or Nd3+ ions dopants

    CERN Document Server

    Cardin, Julien; Dufour, Christian; Gourbilleau, Fabrice

    2015-01-01

    A comparative study of the gain achievement is performed in a waveguide optical amplifier whose active layer is constituted by a silica matrix containing silicon nanograins acting as sensitizer of either neodymium ions (Nd 3+) or erbium ions (Er 3+). Due to the large difference between population levels characteristic times (ms) and finite-difference time step (10 --17 s), the conventional auxiliary differential equation and finite-difference time-domain (ADE-FDTD) method is not appropriate to treat such systems. Consequently, a new two loops algorithm based on ADE-FDTD method is presented in order to model this waveguide optical amplifier. We investigate the steady states regime of both rare earth ions and silicon nanograins levels populations as well as the electromagnetic field for different pumping powers ranging from 1 to 10 4 mW.mm-2. Furthermore, the three dimensional distribution of achievable gain per unit length has been estimated in this pumping range. The Nd 3+ doped waveguide shows a higher gross...

  1. Optical spectra and local structure of Eu3+ ions doped in Nb2O5-La2O3-B2O3-BaO glasses

    Institute of Scientific and Technical Information of China (English)

    Haiping Xia; Jianli Zhang; Jinhao Wang; Yuepin Zhang

    2006-01-01

    @@ The xNb2O5-(15-x)La2O3-40B2O3-45BaO (x = 5, 7.5, 12.5 mol%) glasses doped with Eu3+ ions in 1mol% are fabricated by the melting method. The Fourier transform infrared (FTIR) spectra, phonon sideband spectra, emission and excitation spectra of the glasses are measured. The crystal field parameter and coordination number of Eu3+ ions in the glasses are obtained according to the splitting of their 5D0 - 7F1levels. The intensity parameters Ω2 and Ω4 of Eu3+ ions for optical transition are calculated from their emission spectra in terms of reduced matrix U(t) (λ= 2,4,6) character for optical transitions. The results indicate that the intensity parameters Ω2 and Ω4 increase with the increase of Nb2O5 content, suggesting that the symmetry becomes lower, the band of Eu and O atoms becomes stronger and the covalence increases with the increase of Nb2O5 content.

  2. Effects of Additional Oxygen Flow on the Optical and Electrical Properties of Ion Beam Sputtering Deposited Molybdenum-Doped Zinc Oxide Layer

    Directory of Open Access Journals (Sweden)

    Chin-Chiuan Kuo

    2012-01-01

    Full Text Available The transparent conductive molybdenum-doped zinc oxide (MZO was deposited onto a flexible polyethersulfone (PES substrate by using an ion beam sputtering system. An argon ion beam was used to sputter an MZO target at constant pressure of 0.67 Pa and substrate temperature of 130∘C with varying the oxygen flow rate from 0 to 12 sccm. The influences of additional oxygen flow on the microstructure, optical, and electrical properties of films were investigated. The obtained MZO films present a crystalline structure. With increasing the oxygen flow rate, their electrical resistivity increases, and the optical band gap decreases from 3.46 to 3.20 eV. The film deposited in the atmosphere without introducing oxygen exhibits the best optical transmittance of 82.9% at 550 nm wavelength, electrical resistivity of 8.32 × 10−3 Ω cm, carrier concentration of 6.82 × 1020 cm−3, and carrier mobility of 2.45 cm2/Vs.

  3. Effect of laser annealing using high repetition rate pulsed laser on optical properties of phosphorus-ion-implanted ZnO nanorods

    Science.gov (United States)

    Shimogaki, Tetsuya; Ofuji, Taihei; Tetsuyama, Norihiro; Okazaki, Kota; Higashihata, Mitsuhiro; Nakamura, Daisuke; Ikenoue, Hiroshi; Asano, Tanemasa; Okada, Tatsuo

    2014-02-01

    The effect of high repetition rate pulsed laser annealing with a KrF excimer laser on the optical properties of phosphorus-ion-implanted zinc oxide nanorods has been investigated. The recovery levels of phosphorus-ion-implanted zinc oxide nanorods have been measured by photoluminescence spectra and cathode luminescence images. Cathode luminescence disappeared over 300 nm below the surface due to the damage caused by ion implantation with an acceleration voltage of 25 kV. When the annealing was performed at a low repetition rate of the KrF excimer laser, cathode luminescence was recovered only in a shallow area below the surface. The depth of the annealed area was increased along with the repetition rate of the annealing laser. By optimizing the annealing conditions such as the repetition rate, the irradiation fluence and so on, we have succeeded in annealing the whole damaged area of over 300 nm in depth and in observing cathode luminescence. Thus, the effectiveness of high repetition rate pulsed laser annealing on phosphorus-ion-implanted zinc oxide nanorods was demonstrated.

  4. Influence of Ni substitution at B-site for Fe{sup 3+} ions on morphological, optical, and magnetic properties of HoFeO{sub 3} ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Habib, Zubida; Majid, Kowsar [National Institute of Technology, Department of Chemistry, Srinagar (India); Ikram, Mohd; Sultan, Khalid; Mir, Sajad Ahmad [National Institute of Technology, Department of Physics, Srinagar (India); Asokan, K. [Inter University Accelerator Centre, New Delhi (India)

    2016-05-15

    Present study reports the effect of Ni substitution at B-site in HoFeO{sub 3} on the morphological, optical and magnetic properties. These compounds were prepared by solid-state reaction method. Scanning electron microscope reveals an increase in average grain sizes with Ni concentration. Absorption and emission spectra show redshift in band gap with increase in Ni ion concentrations. The Tauc plots show direct allowed transitions. Temperature-dependent magnetization studies on these compounds revealed the transition from ferromagnetism to paramagnetism. There is separation between temperature at which zero-field-cooled and field-cooled occurs at varied temperature with Ni substitution. The separation effect is related to the impact of the paramagnetic Ho{sup 3+} ions, whose magnitude becomes more prominent at higher temperature. The value of squareness ratio in these materials is below 0.5 indicating presence of multidomain structures. (orig.)

  5. Optical properties of silica sol-gel materials singly-and doubly-doped with Eu3+and Gd3+ions

    Institute of Scientific and Technical Information of China (English)

    Natalia Pawlik; Barbara Szpikowska-Sroka; Marta Sołtys; Wojciech A.Pisarski

    2016-01-01

    In present work, the optical and structural properties of silica sol-gel glasses and glass-ceramic materials singly-and dou-bly-doped with Eu3+and Gd3+ions were investigated. The optical properties of studied systems were determined based on absorption, excitation and emission spectra as well as luminescence decay analysis. Conducted studies clearly indicated a significant enhance-ment of visible emission originated from Eu3+ions as a result of changing the excitation mechanism, via Gd3+→Eu3+energy transfer. The luminescence intensity R-ratio was analyzed before and after heat-treatment process upon excitation atλex=393 nm andλex=273 nm. Moreover, the influence of excitation wavelength on luminescence decay time of the 5D0 excited state was also analyzed. The Gd3+→Eu3+energy transfer efficiencies for precursor and annealed samples were calculated based on luminescence lifetime of the 6P7/2 level of Gd3+ions. The X-ray diffraction measurements were conducted to verify the nature of obtained sol-gel materials. In re-sult, the formation of orthorhombic GdF3 nanocrystal phase dispersed in amorphous silica glass host was identified after annealing. Obtained results clearly indicated an incorporation of Eu3+ activators into formed GdF3 nanocrystals. Thus, conducted heat-treatment process led to considerable changes in surrounding environment around Eu3+ions. Actually, it was found that en-ergy transfer phenomenon and heat-treatment process were responsible for significant improvement of Eu3+luminescence in stud-ied sol-gel samples.

  6. Selective Iron(III ion uptake using CuO-TiO2 nanostructure by inductively coupled plasma-optical emission spectrometry

    Directory of Open Access Journals (Sweden)

    Rahman Mohammed M

    2012-12-01

    Full Text Available Abstract Background CuO-TiO2 nanosheets (NSs, a kind of nanomaterials is one of the most attracting class of transition doped semiconductor materials due to its interesting and important optical, electrical, and structural properties and has many technical applications, such as in metal ions detection, photocatalysis, Chemi-sensors, bio-sensors, solar cells and so on. In this paper the synthesis of CuO-TiO2 nanosheets by the wet-chemically technique is reported. Methods CuO-TiO2 NSs were prepared by a wet-chemical process using reducing agents in alkaline medium and characterized by UV/vis., FT-IR spectroscopy, X-ray photoelectron spectroscopy (XPS, powder X-ray diffraction (XRD, and field-emission scanning electron microscopy (FE-SEM etc. Results The structural and optical evaluation of synthesized NSs were measured by XRD pattern, Fourier transform infrared (FT-IR and UV–vis spectroscopy, respectively which confirmed that the obtained NSs are well-crystalline CuO-TiO2 and possessing good optical properties. The morphological analysis of CuO-TiO2 NSs was executed by FE-SEM, which confirmed that the doped products were sheet-shaped and growth in large quantity. Here, the analytical efficiency of the NSs was applied for a selective adsorption of iron(III ion prior to detection by inductively coupled plasma-optical emission spectrometry (ICP-OES. The selectivity of NSs towards various metal ions, including Au(III, Cd(II, Co(II, Cr(III, Fe(III, Pd(II, and Zn(II was analyzed. Conclusions Based on the selectivity study, it was confirmed that the selectivity of doped NSs phase was the most towards Fe(III ion. The static adsorption capacity for Fe(III was calculated to be 110.06 mgg−1. Results from adsorption isotherm also verified that the adsorption process was mainly monolayer-adsorption onto a surface containing a finite number of CuO-TiO2 NSs adsorption sites.

  7. Modifications in structure and optical property of Cu nanoparticles in SiO{sub 2} by post heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Changlong, E-mail: liuchanglong@tju.edu.cn [School of Science, Tianjin University, Tianjin 300072 (China); Tianjin Key Laboratory of Low Dimensional Materials Physics and Preparing Technology, Institute of Advanced Materials Physics, Faculty of Science, Tianjin 300072 (China); Key Laboratory of Beam Technology and Material Modification of Ministry of Education, Beijing Normal University, Beijing 100875 (China); Wang, Nana; Wang, Jun; Liu, Huixian; Jia, Guangyi; Mu, Xiaoyu [School of Science, Tianjin University, Tianjin 300072 (China)

    2014-05-01

    The implantation-synthesized Cu nanoparticles (NPs) in silica were irradiated with 500 keV Xe and Ar ions, respectively. After Xe ion irradiation at a fluence of 2 × 10{sup 16}/cm{sup 2}, the average diameter of Cu NPs was increased from 7.3 to 8.5 nm, and especially, Cu NPs with a diameter of 11–14 nm were formed beyond the projected range of Cu ions and nearly aligned at the same depth, which presented a higher volume fraction. As a result, the Cu surface plasmon resonance (SPR) absorption peak was enhanced. However, if Xe ion fluence was less than 1 × 10{sup 16}/cm{sup 2}, no clear variation of the Cu SPR absorption peak could be found. Further, it was also revealed that Xe ion irradiation caused the Cu SPR absorption peak to more drastically change than Ar ion irradiation at the same ion fluence. The underlying processes for the above findings were discussed and tentatively proposed.

  8. The Influences of Thickness on the Optical and Electrical Properties of Dual-Ion-Beam Sputtering-Deposited Molybdenum-Doped Zinc Oxide Layer

    Directory of Open Access Journals (Sweden)

    Chin-Chiuan Kuo

    2011-01-01

    Full Text Available The thickness of transparent conductive oxide (TCO layer significantly affects not only the optical and electrical properties, but also its mechanical durability. To evaluate these influences on the molybdenum-doped zinc oxide layer deposited on a flexible polyethersulfone (PES substrate by using a dual-ion-beam sputtering system, films with various thicknesses were prepared at a same condition and their optical and electrical performances have been compared. The results show that all the deposited films present a crystalline wurtzite structure, but the preferred orientation changes from (002 to (100 with increasing the film thickness. Thicker layer contains a relative higher carrier concentration, but the consequently accumulated higher internal stress might crack the film and retard the carrier mobility. The competition of these two opposite trends for carrier concentration and carrier mobility results in that the electrical resistivity of molybdenum-doped zinc oxide first decreases with the thickness but suddenly rises when a critical thickness is reached.

  9. Optical investigation of the propagation of the amorphous-crystalline boundary in ion-beam irradiated LiNbO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Olivares, J. [Instituto de Optica ' Daza de Valdes' , CSIC, Serrano 121, 28006 Madrid (Spain); Garcia, G. [Centro de Microanalisis de Materiales, CMAM-UAM, Parque Cientifico de Madrid, Cantoblanco, E-28049 Madrid (Spain); Agullo-Lopez, F. [Centro de Microanalisis de Materiales, CMAM-UAM, Parque Cientifico de Madrid, Cantoblanco, E-28049 Madrid (Spain); Departamento de Fisica de Materiales, C-IV, Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Agullo-Rueda, F. [Instituto de Ciencia de Materiales de Madrid, CSIC, Cantoblanco, E-28049 Madrid (Spain); Soares, J.C. [Centro de Fisica Nuclear da Universidade de Lisboa, P-1649-003 Lisbon (Portugal); Kling, A. [Instituto Tecnologico e Nuclear (ITN), P-2685 Sacavem (Portugal)

    2006-01-15

    The effects of high-energy silicon (5 MeV, 7.5 MeV and 30 MeV) irradiations have been optically investigated by the dark-mode m-lines technique. In all cases, an optically isotropic homogeneous layer is created after a certain critical fluence that depends on ion and energy. The structure of the layer has been investigated by micro-Raman spectroscopy and RBS/channeling. The inner boundary of the layer separating the amorphous and crystalline regions moves into the crystal on increasing fluence. The results are discussed based on the occurrence of a sharp threshold in the electronic stopping power leading to the formation of overlapped latent (amorphous) tracks.

  10. Effect of fluoride ions on the optical properties of Eu{sup 3+}:PbF{sub 2} nanocrystals embedded into sol–gel host materials

    Energy Technology Data Exchange (ETDEWEB)

    Szpikowska-Sroka, Barbara, E-mail: barbara.szpikowska-sroka@us.edu.pl; Pawlik, Natalia; Żur, Lidia; Czoik, Rozalia; Goryczka, Tomasz; Pisarski, Wojciech A.

    2016-05-01

    In this research, the effects of fluoride ions concentration on luminescence properties of Eu{sup 3+}:PbF{sub 2} nanocrystals in silicate sol–gel materials have been investigated. Optical and structural properties of Eu{sup 3+}:PbF{sub 2} nanocrystals have been examined using X-ray diffraction analysis (XRD) and luminescence spectroscopy. Formation of the cubic β-PbF{sub 2} nanocrystalline phase was confirmed. The crystal size was estimated using Scherrer's equation and Williamson-Hall formula. The optical behavior of Eu{sup 3+} ions in studied materials is strongly dependent on amount of incorporated fluorides in the host lattice and the optimal concentration about 3.0 mass. % give the more intense emission of Eu{sup 3+}. The luminescence spectra showed the characteristic orange-red emission due to the {sup 5}D{sub 0} → {sup 7}F{sub 1} and {sup 5}D{sub 0} → {sup 7}F{sub 2} electron transitions, respectively. The luminescence intensity ratio R (I({sup 5}D{sub 0} → {sup 7}F{sub 2})/I({sup 5}D{sub 0} → {sup 7}F{sub 1})) and luminescence lifetimes for the {sup 5}D{sub 0} excited state of Eu{sup 3+} ions were determined for each sample before and after heat treatment process. Obtained results indicate the partially incorporation of Eu{sup 3+} ions into β-PbF{sub 2} nanocrystalline phase during ceramization process. - Highlights: • The effect of fluoride ions concentration on luminescence properties was studied. • Formation of cubic β-PbF{sub 2} nanocrystalline phase was confirmed. • The crystal size was estimated using Scherrer's and Williamson-Hall methods. • Luminescence decay curves of the investigated sol–gel glasses were examined. • The results indicate incorporation of Eu{sup 3+} ions into nanocrystalline phase.

  11. Effect of ion bombardment on the structural and optical properties of TiO{sub 2} thin films deposited from oxygen/titanium tetraisopropoxide inductively coupled plasma

    Energy Technology Data Exchange (ETDEWEB)

    Li, D. [College of Mechanical Engineering, Yangzhou University, Yangzhou 225127 (China); Carette, M.; Granier, A.; Landesman, J.P. [Institut des Matériaux Jean Rouxel (IMN), Université de Nantes, UMR CNRS 6502, 2 rue de la Houssinière, BP 32229, 44322 Nantes Cedex 3 (France); Goullet, A., E-mail: antoine.goullet@univ-nantes.fr [Institut des Matériaux Jean Rouxel (IMN), Université de Nantes, UMR CNRS 6502, 2 rue de la Houssinière, BP 32229, 44322 Nantes Cedex 3 (France)

    2015-08-31

    Titanium dioxide films were deposited on silicon substrates from oxygen/titanium tetraisopropoxide inductively coupled radiofrequency plasmas in a helicon reactor operated at low temperature (< 150 °C) and low pressure (0.4 Pa). The effect of the ion energy (E{sub i}), varied in the 15–175 eV range, on the morphology, microstructure and optical properties of the films is investigated. Scanning electron microscopy (SEM) shows that at low energy (E{sub i} = 15 eV), the film exhibits a columnar morphology consisting of a bottom dense layer, an intermediate gradient layer and a top roughness layer. Increasing the ion energy results in more homogeneous films along the growth direction as confirmed by the in-situ kinetic ellipsometry measurements and post deposition spectroscopic ellipsometry data analysis. In addition, the atomic force microscopy (AFM) measurements reveal that the film top surface becomes smoother as E{sub i} is increased. X-ray diffraction (XRD) diagrams show that only anatase is identified in the film deposited at 15 eV, whereas the complete phase transformation from anatase to rutile occurs at E{sub i} = 75 eV. These results are in good agreement with the Fourier transform infrared spectroscopy (FTIR) spectra which also show that the hydroxyl groups absorbed in the films deposited at 15 eV, are greatly decreased for E{sub i} ≥ 45 eV. Suitable structural models combined with the Tauc–Lorentz dispersion law have been found to accurately fit the spectroscopic ellipsometry experimental data. The results in good agreement with SEM and AFM measurements are also consistent with the structural properties evidenced by XRD and FTIR. The refractive index (n) can be increased significantly by increasing the ion energy from 15 eV to 75 eV, reaching a value of 2.49 at 1.96 eV. Upon increasing the ion energy above 75 eV n is shown to decrease due to micropores which are formed in the films. - Highlights: • TiO{sub 2} thin films deposited in inductively

  12. Effect of Li+ ion sensitization and optical temperature sensing in Gd2O3: Ho3+/Yb3+

    Science.gov (United States)

    Singh, Priyam; Shahi, P. K.; Rai, Anita; Bahadur, A.; Rai, S. B.

    2016-08-01

    Ho3+/Yb3+ codoped Gd2O3 phosphor has been synthesized by solution combustion method. The concentrations of Ho3+ and Yb3+ were optimized to be 0.3 and 2.0 mol% respectively for maximum emission intensity. The effect of Li+ ion co-doping on phase structure and photo luminescence were investigated. It is found that there is no change in phase of the sample due to Li+ ion co-doping. However the Upconversion (UC) and Downshifting (DS) emission show a remarkable enhancement in intensity. It is concluded that, this enhancement in the emission intensity is mainly due to the change in crystal field around the Ho3+ ion and reduction in quenching centers. The optimum doping concentration of Li+ ion was found to be 20 mol%. We have further explored the temperature sensing behavior using the FIR technique. The maximum sensitivity is found to be 0.0092 K-1 at 505 K.

  13. Optical Observation of the Ionospheric-Magnetospheric Outflowing Oxygen Ions by XUV Onboard Sounding Rocket SS-520-2

    Science.gov (United States)

    Tashiro, S.; Yamazaki, A.; Yoshikawa, I.; Takizawa, Y.; Miyake, W.; Endo, M.; Nakamura, M.

    2001-12-01

    We built the Extreme ultraviolet scanner (XUV) for imaging oxygen ions to outflow from the polar ionosphere into the magnetosphere. The XUV onboard a sounding rocket SS-520-2 imaged the oxygen ions above 1000 km altitude near the polar cusp on December 4, 2000. The XUV is a normal incidence telescope that has a peak sensitivity at the wavelength 83.4 [nm] of OII emission and consists of a Mo coated mirror, a band pass filter and a channel electron multiplier. The band pass filter selectively transmits OII emission and eliminates background emissions such as HeI emission at the 30.4 [nm], HeII emission at the 58.4 [nm], and HI emission at the 121.6 [nm]. The observed OII emission intensity is proportional to the ion density integrated along the line of sight. Therefore The observed OII emission intensity distribution makes possible to determine the oxygen ion distribution. We will present the oxygen ion distribution and discuss the process and quantity of that ionospheric oxygen ions outflow into the magnetosphere.

  14. Quenching effect in an optical fiber type small size dosimeter irradiated with 290 MeV·u{sup -1} carbon ions

    Energy Technology Data Exchange (ETDEWEB)

    Hirata, Yuho; Watanabe, Kenichi; Uritani, Akira; Yamazaki, Atsushi [Graduate School of Engineering, Nagoya University, Nagoya (Japan); Koba, Yusuke; Matsufuji, Naruhiro [National Institute of Radiological Sciences, Chiba (Japan)

    2016-09-15

    We are developing a small size dosimeter for dose estimation in particle therapies. The developed dosimeter is an optical fiber based dosimeter mounting an radiation induced luminescence material, such as an OSL or a scintillator, at a tip. These materials generally suffer from the quenching effect under high LET particle irradiation. We fabricated two types of the small size dosimeters. They used an OSL material Eu:BaFBr and a BGO scintillator. Carbon ions were irradiated into the fabricated dosimeters at Heavy Ion Medical Accelerator in Chiba (HIMAC). The small size dosimeters were set behind the water equivalent acrylic phantom. Bragg peak was observed by changing the phantom thickness. An ion chamber was also placed near the small size dosimeters as a reference. Eu:BaFBr and BGO dosimeters showed a Bragg peak at the same thickness as the ion chamber. Under high LET particle irradiation, the response of the luminescence-based small size dosimeters deteriorated compared with that of the ion chamber due to the quenching effect. We confirmed the luminescence efficiency of Eu:BaFBr and BGO decrease with the LET. The reduction coefficient of luminescence efficiency was different between the BGO and the Eu:BaFBr. The LET can be determined from the luminescence ratio between Eu:BaFBr and BGO, and the dosimeter response can be corrected. We evaluated the LET dependence of the luminescence efficiency of the BGO and Eu:BaFBr as the quenching effect. We propose and discuss the correction of the quenching effect using the signal intensity ratio of the both materials. Although the correction precision is not sufficient, feasibility of the proposed correction method is proved through basic experiments.

  15. Investigation of structural and optical properties of CaTiO{sub 3} powders doped with Mg{sup 2+} and Eu{sup 3+} ions

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Larissa H., E-mail: larissahelena2009@gmail.com [Institute of Chemistry, State University of São Paulo, 14800-900, Araraquara, São Paulo (Brazil); Savioli, Julia [Department of Chemistry, Federal University of São Carlos, 13565-905, São Carlos, São Paulo (Brazil); Moura, Ana P. de [Institute of Chemistry, State University of São Paulo, 14800-900, Araraquara, São Paulo (Brazil); Nogueira, Içamira C. [Department of Chemistry, Federal University of São Carlos, 13565-905, São Carlos, São Paulo (Brazil); Li, Maximo S. [Institute of Physics, University of São Paulo, P.O. Box, 13566-590, São Carlos, São Paulo (Brazil); Longo, Elson; Varela, José A. [Institute of Chemistry, State University of São Paulo, 14800-900, Araraquara, São Paulo (Brazil); Rosa, Ieda L.V. [Department of Chemistry, Federal University of São Carlos, 13565-905, São Carlos, São Paulo (Brazil)

    2015-10-25

    In this work, CaTiO{sub 3} powders doped with Mg{sup 2+} ions and CaTiO{sub 3} powders co-doped with Mg{sup 2+} and Eu{sup 3+} ions were prepared by the polymeric precursor method (PPM). These powders were characterized by different characterization techniques to study the influence of Mg{sup 2+} doping as well as Mg{sup 2+} and Eu{sup 3+} co-doping in structural and optical properties of CaTiO{sub 3} perovskite-type structure. The Rietveld refinement and Micro-Raman analyses suggested the substitution Mg{sup 2+} and Eu{sup 3+} ions in the A-site of CaTiO{sub 3} perovskite. The influence of Mg{sup 2+} doping can be detected by the displacement of calcium and oxygen atomic positions when compared to the non-doped CaTiO{sub 3} powder. When Eu{sup 3+} ions are added to the A-site of this perovskite the excess of positive charge can be compensated by the formation of calcium vacancies. Luminescence data showed that Ca{sub 1-x}Mg{sub x}TiO{sub 3} and Ca{sub 1x}Mg{sub x/2}Eu{sub 2y/3}TiO{sub 3} powders are potential materials for fabrication of lighting devices based on near-UV and blue LED using an excitation wavelength of 397 and/or 450 nm. - Highlights: • CaTiO{sub 3} co-doped with Mg{sup 2+} and Eu{sup 3+} were obtained by the Polymeric Precursor Method. • Incorporation of Mg{sup 2+} and Eu{sup 3+} ions in the CaTiO{sub 3} lattice. • Enhancement of the Eu{sup 3+} photoluminescence.

  16. M-line spectroscopic, spectroscopic ellipsometric and microscopic measurements of optical waveguides fabricated by MeV-energy N{sup +} ion irradiation for telecom applications

    Energy Technology Data Exchange (ETDEWEB)

    Bányász, I., E-mail: banyasz@sunserv.kfki.hu [Wigner Research Centre for Physics, Hungarian Academy of Sciences, P.O.B. 49, H-1525, Budapest (Hungary); Berneschi, S. [“Enrico Fermi” Center for Study and Research, Piazza del Viminale 2, 00184 Roma (Italy); MDF-Lab, “Nello Carrara” Institute of Applied Physics, IFAC-CNR, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy); Fried, M.; Lohner, T. [Institute of Technical Physics and Materials Science, Research Centre for Natural Sciences, Hungarian Academy of Sciences, P.O.B. 49, H-1525, Budapest (Hungary); Conti, G. Nunzi; Righini, G.C.; Pelli, S. [MDF-Lab, “Nello Carrara” Institute of Applied Physics, IFAC-CNR, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy); Zolnai, Z. [Institute of Technical Physics and Materials Science, Research Centre for Natural Sciences, Hungarian Academy of Sciences, P.O.B. 49, H-1525, Budapest (Hungary)

    2013-08-31

    Irradiation with N{sup +} ions of the 1.5–3.5 MeV energy range was applied to optical waveguide formation. Planar and channel waveguides have been fabricated in an Er-doped tungsten–tellurite glass, and in both types of bismuth germanate (BGO) crystals: Bi{sub 4}Ge{sub 3}O{sub 12} (eulytine) and Bi{sub 12}GeO{sub 20} (sillenite). Multi-wavelength m-line spectroscopy and spectroscopic ellipsometry were used for the characterisation of the ion beam irradiated waveguides. Planar waveguides fabricated in the Er-doped tungsten–tellurite glass using irradiation with N{sup +} ions at 3.5 MeV worked even at the 1550 nm telecommunication wavelength. 3.5 MeV N{sup +} ion irradiated planar waveguides in eulytine-type BGO worked up to 1550 nm and those in sillenite-type BGO worked up to 1330 nm. - Highlights: ► Waveguides were fabricated in glass and crystals using MeV energy N{sup +} ions. ► SRIM simulation and spectroscopic ellipsometry yielded similar waveguide structures. ► Multi-wavelength m-line spectroscopy was used to study the waveguides. ► Waveguides fabricated in an Er-doped tungsten–tellurite glass worked up to 1.5 μm. ► Waveguides in Bi{sub 12}GeO{sub 20} remained operative up to 1.5 μm.

  17. Tailor-made micro-object optical sensor based on mesoporous pellets for visual monitoring and removal of toxic metal ions from aqueous media.

    Science.gov (United States)

    El-Safty, Sherif A; Shenashen, M A; Shahat, A

    2013-07-08

    Methods for the continuous monitoring and removal of ultra-trace levels of toxic inorganic species (e.g., mercury, copper, and cadmium ions) from aqueous media such as drinking water and biological fluids are essential. In this paper, the design and engineering of a simple, pH-dependent, micro-object optical sensor is described based on mesoporous aluminosilica pellets with an adsorbed dressing receptor (a porphyrinic chelating ligand). This tailor-made optical sensor permits ultra-fast (≤ 60 s), specific, pH-dependent visualization and removal of Cu(2+) , Cd(2+) , and Hg(2+) at sub-picomolar concentrations (∼10(-11) mol dm(-3) ) from aqueous media, including drinking water and a suspension of red blood cells. The acidic active acid sites of the pellets consist of heteroatoms arranged around uniformly shaped pores in 3D nanoscale gyroidal mesostructures densely coated with the chelating ligand. The sensor can be used in batch mode, as well as in a flow-through system in which sampling, target ion recognition and removal, and analysis are integrated in a highly automated and efficient manner. Because the pellets exhibit long-term stability, reproducibility, and versatility over a number of analysis/regeneration cycles, they can be expected to be useful for the fabrication of inexpensive sensor devices for naked-eye detection of toxic pollutants.

  18. Mesomorphism and Optical Properties of Peripherally Substituted Phthalocyanines: Influence of Chain Length, Linking Group and Central Metal Ion

    OpenAIRE

    Sleven, Jurgen

    2002-01-01

    Phthalocyanines form a colourful class of macrocyclic compounds, attracting the attention of many scientists. Some of these compounds – especially the metal containing phthalocyanines – play an important role in industrial activity and in society. Applications for phthalocyanines are found in the fields of non-linear optics, catalysis, electronic (bio)sensors, photovoltaic solar cells, optical data storage, lubricants, photo- and radiosensitizers for treatment of cancer, protein inhibitors … ...

  19. Processing for optically active erbium in silicon by film co-deposition and ion-beam mixing

    Energy Technology Data Exchange (ETDEWEB)

    Abedrabbo, S., E-mail: sxa0215@yahoo.com [Department of Physics, University of Jordan, Amman 11942 (Jordan); Mohammed, Q. [Tadawul Shares and Bonds Mediation L.L.C., Dubai (United Arab Emirates); Fiory, A.T. [Department of Physics, New Jersey Institute of Technology, Newark, NJ 07901 (United States)

    2009-02-01

    Techniques of film deposition by co-evaporation, ion-beam assisted mixing, oxygen ion implantation, and thermal annealing were been combined in a novel way to study processing of erbium-in-silicon thin-film materials for optoelectronics applications. Structures with erbium concentrations above atomic solubility in silicon and below that of silicide compounds were prepared by vacuum co-evaporation from two elemental sources to deposit 200-270 nm films on crystalline silicon substrates. Ar{sup +} ions were implanted at 300 keV. Oxygen was incorporated by O{sup +}-ion implantation at 130 keV. Samples were annealed at 600 deg. C in vacuum. Concentration profiles of the constituent elements were obtained by Rutherford backscattering spectrometry. Results show that diffusion induced by ion-beam mixing and activated by thermal annealing depends on the deposited Si-Er profile and reaction with implanted oxygen. Room temperature photoluminescence spectra show Er{sup 3+} transitions in a 1480-1550 nm band and integrated intensities that increase with the oxygen-to-erbium ratio.

  20. Evaluation of blackbody radiation shift with temperature associated fractional uncertainty at 10E-18 level for 40Ca+ ion optical clock

    CERN Document Server

    Zhang, Ping; Shu, Hua-lin; Yuan, Jin-bo; Shang, Juan-juan; Cui, Kai-feng; Chao, Si-jia; Wang, Shao-mao; Liu, Dao-xin; Huang, Xue-ren

    2016-01-01

    In this paper, blackbody radiation (BBR) temperature rise seen by the $^{40}$Ca$^+$ ion confined in a miniature Paul trap and its uncertainty have been evaluated via finite-element method (FEM) modelling. The FEM model was validated by comparing with thermal camera measurements, which were calibrated by PT1000 resistance thermometer, at several points on a dummy trap. The input modelling parameters were analyzed carefully in detail, and their contributions to the uncertainty of environment temperature were evaluated on the validated FEM model. The result shows that the temperature rise seen by $^{40}$Ca$^+$ ion is 1.72 K with an uncertainty of 0.46 K. It results in a contribution of 2.2 mHz to the systematic uncertainty of $^{40}$Ca$^+$ ion optical clock, corresponding to a fractional uncertainty 5.4$\\times$10$^{-18}$. This is much smaller than the uncertainty caused by the BBR shift coefficient, which is evaluated to be 4.8 mHz and at 10$^{-17}$ level in fractional frequency units.

  1. Evaluation of blackbody radiation shift with temperature-associated fractional uncertainty at 10-18 level for 40Ca+ ion optical clock

    Science.gov (United States)

    Zhang, Ping; Cao, Jian; Shu, Hua-lin; Yuan, Jin-bo; Shang, Jun-juan; Cui, Kai-feng; Chao, Si-jia; Wang, Shao-mao; Liu, Dao-xin; Huang, Xue-ren

    2017-01-01

    In this paper, the blackbody radiation (BBR) temperature rise experienced by a 40Ca+ ion confined in a miniature Paul trap and its uncertainty have been evaluated via finite-element method (FEM) modelling. The FEM model was validated through comparisons with thermal camera measurements at several points on a dummy trap. Before the validation, the thermal camera was calibrated by using a PT1000 resistance thermometer. The input modelling parameters were analyzed carefully, and their contributions to the uncertainty of the trap environment temperature were evaluated using the validated FEM model. The result shows that the temperature rise experienced by the 40Ca+ ion is 1.72 K with an uncertainty of 0.46 K. It results in a contribution of 2.2 mHz to the systematic uncertainty of a 40Ca+ ion optical clock, corresponding to a fractional uncertainty 5.4 × 10-18. This is much smaller than the uncertainty caused by the BBR shift coefficient, which is evaluated to be 4.8 mHz and at the 10-17 level in fractional frequency units.

  2. Highly charged W+13, Ir+16, and Pt+17 ions as promising optical clock candidates for probing variations of the fine-structure constant

    Science.gov (United States)

    Nandy, D. K.; Sahoo, B. K.

    2016-09-01

    Transitions among the first three low-lying states in the highly charged W+13, Ir+16, and Pt+17 ions are found to be strongly forbidden with wavelengths in the optical regime. By determining their energy levels, lifetimes, and other spectroscopic properties that are decisive quantities for estimating dominant systematics due to stray electromagnetic interactions in an experiment, we demonstrate that it can be possible to measure frequencies of the lowest forbidden transitions below a 10-19 precision level in the above ions, and hence, they seem to be suitable for frequency standards. We employ a sophisticated relativistic coupled cluster method to carry out calculations of these properties of the above states involving 4 f - and 5 s -core orbitals. We also found, by estimating their relativistic sensitivity coefficients, that these clock transitions can be highly sensitive to the tiny drift in the fine-structure constant αe. Consequently, a clock based on one of these ions, particularly Pt+17, could be used for corroborating the hypothesis of temporal and spatial variation in αe.

  3. Effect of Eu ion incorporation on the emission behavior of Y2O3 nanophosphors: A detailed study of structural and optical properties

    Science.gov (United States)

    Kumar, Y.; Pal, Mou; Herrera, M.; Mathew, X.

    2016-10-01

    In order to investigate the effect of doping concentration on the luminescence behavior of yttrium oxide (Y2O3) europium (Eu) doped nanoparticles were prepared by co-precipitation method. Incorporation of Eu ion in Y2O3 matrix is clearly reflected in structural and optical properties of the doped Y2O3 phosphor. Cathodoluminescence (CL) spectroscopy proves the presence of strong Eu3+ emissions along with the presence of an additional weak band corresponding to electronic transitions 4f65d1 (7FJ) - 4f7 (8S7/2) of the Eu2+. The presence of Eu3+ and Eu2+ ions in Y2O3 nanoparticles have been additionally confirmed by XPS analysis. Luminescence band corresponding to Eu3+ ions appears in both CL and photoluminescence (PL) spectra, covering the orange-red emissions from 580 to 710 nm. Vibrational properties analyzed through Raman spectroscopy have revealed the evolution of different peaks associated with Eu emission in the doped Y2O3 nanocrystals.

  4. First-order ion-optics calculations for an Accelerator Mass Spectrometry system using SRIM and S{sup 3}M

    Energy Technology Data Exchange (ETDEWEB)

    Gomez-Guzman, J.M., E-mail: jm_gomez@us.es [Centro Nacional de Aceleradores (CNA), Avda. Thomas Alva Edison 7, Isla de la Cartuja, 41092 Seville (Spain); Dpto. de Fisica Atomica, Molecular y Nuclear, University of Seville (Spain); Gomez-Morilla, I. [Technische Universitaet Dresden, Fakultaet Maschinenwesen, Professur fuer Magnetofluiddynamik (Germany); Enamorado-Baez, S.M.; Moreno Suarez, A.I.; Pinto-Gomez, A.R. [Centro Nacional de Aceleradores (CNA), Avda. Thomas Alva Edison 7, Isla de la Cartuja, 41092 Seville (Spain)

    2012-06-15

    In this paper, we describe the transport of a simulated beam, created with the S{sup 3}M beam generation module, along the real beam line of the Accelerator Mass Spectrometry (AMS) facility located at Centro Nacional de Aceleradores (CNA, Seville, Spain). The beam transport through the optical system was determined using the transfer-matrix method, which can easily calculate the beam envelopes without having to track all individual particles, evaluating the ability of such systems and saving computation time. The beam size results given by S{sup 3}M were compared to the real beam size in three of the four image points that the system has (P1, P2 and P3), corresponding with the position of Faradays Cups where the {sup 127}I current was measured, obtaining a good agreement between them. This suggests that the first order approximation model is enough to simulate the optical behavior of the system. It is shown that the beam line has a focusing behavior, minimizing the beam size from {+-}3 mm at the exit of the ion source to {+-}1.09 mm at the detector's entrance window. Using the beam emittance diagram simulations, it is shown that when ions pass through the stripper, the angles of their trajectories are altered by scattering with the gas molecules and the geometrical emittance enlarges, according to Liouville's Theorem. The study presented in this work gives confidence and open new perspectives in simulations with S{sup 3}M in AMS facilities contributing to the understanding of their optical behavior.

  5. Comparative analysis of luminescent properties of germanate glass and double-clad optical fibers co-doped with Yb3+/Ho3+ ions

    Science.gov (United States)

    Pietrzycki, Marcin; Kochanowicz, Marcin; Romańczuk, Patryk; Żmojda, Jacek; Miluski, Piotr; Ragiń, Tomasz; Jeleń, Piotr; Sitarz, Maciej; Dorosz, Dominik

    2016-09-01

    The 2 μm and visible emission of low phonon (805 cm-1) germanate glasses and double - clad optical fiber co-doped with 0.7Yb2O3/(0.07-0.7)Ho2O3 ions have been investigated. Luminescence at 2 μm corresponding to Ho3+: 5I7 → 5I8 as well as upconversion luminescence in the visible spectral range corresponding to the Ho3+: 5S2(5F4)→5I8 (545 nm), and Ho3+: 5F5→5I8 (655 nm) transition, respectively were obtained. The optimization of the acceptor content and donor-acceptor ratio were conducted with the purpose of maximizing the luminescence intensity. The highest luminescence intensity in both spectral range was obtained in glass co-doped with 0.7Yb2O3/0.15 Ho2O3. Despite relatively small effective absorption coefficient of the optical fiber comparative analysis of luminescent properties of fabricated glasses (further core) and double - clad optical fiber showed significant contribution of reabsorption process of emitted ASE signal.

  6. Effect of doping of Nd3+ ions in BaO-TeO2-B2O3 glasses: A vibrational and optical study

    Science.gov (United States)

    Nanda, Kirti; Berwal, Neelam; Kundu, R. S.; Punia, R.; Kishore, N.

    2015-05-01

    Nd3+ ions doped Barium-Tellurite-Borate glasses with compositions xNd2O3 - (100 - x)[0.1BaO-0.4TeO2-0.5B2O3]; x = 0.0, 0.5, 1.0, 1.5 and 2.0 have been prepared by melt-quench technique. The amorphous nature of as-prepared glasses has been confirmed by X-ray diffraction patterns. The density, molar volume and equivalent crystalline volume of the glass samples have been found to increase with the increase in concentration of Nd2O3. FTIR and Raman spectra of the prepared glasses indicate that Nd2O3 acts as glass modifier and as the content of Nd2O3 increases, BO4 structural units are converted into BO3 structural units. The values of optical band gap have been estimated from the fitting of Mott and Davis's model with the experimentally observed absorption spectra. The experimentally observed spectra of absorption coefficient also show good agreement with the hydrogenic excitonic model and the values of different parameters like optical band gap, excitonic binding energy, line width of m = 1 state and line width of continuum have been estimated from theoretical fitting of this model. The values of optical band gap are observed to decrease with increase in concentration of Nd2O3.

  7. Effect of 50MeV Li{sup 3+} ion irradiation on structural, optical and electrical properties of amorphous Se{sub 95}Zn{sub 5} thin films

    Energy Technology Data Exchange (ETDEWEB)

    Ahmad, Shabir, E-mail: shaphyjmi@gmail.com; Sethi, Riti; Nasir, Mohd; Zulfequar, M., E-mail: zulfequarphy@rediffmail.com [Department of physics, JamiaMilliaIslamia, New Delhi-110025 (India); Asokan, K., E-mail: asokan42@gmail.com [Materials Science Division, Inter University Accelerator Centre, New Delhi-110067 (India)

    2015-08-28

    Present work focuses on the effect of swift heavy ion (SHI) irradiation of 50MeV Li{sup 3+} ions by varying the fluencies in the range of 1×10{sup 12} to 5×10{sup 13} ions/cm{sup 2} on the morphological, structural, optical and electrical properties of amorphous Se{sub 95}Zn{sub 5} thin films. Thin films of ~250nm thickness were deposited on cleaned glass substrates by thermal evaporation technique. X-ray diffraction (XRD) analysis shows the pristine thin film of Se{sub 95}Zn{sub 5} growsin hexagonal phase structure. Also it was found that the small peak observed in XRD spectra vanishes after SHI irradiation indicates the defects of the material increases. The optical parameters: absorption coefficient (α), extinction coefficient (K), refractive index (n) optical band gap (E{sub g}) and Urbach’s energy (E{sub U}) are determined from optical absorption spectra data measured from spectrophotometry in the wavelength range 200-1000nm. It was found that the values of absorption coefficient, refractive index and extinction coefficient increases while the value optical band gap decreases with the increase of ion fluence. This post irradiation change in the optical parameters was interpreted in terms of bond distribution model. Electrical properties such as dc conductivity and temperature dependent photoconductivity of investigated thin films were carried out in the temperature range 309-370 K. Analysis of data shows activation energy of dark current is greater as compared to activation energy photocurrent. The value of activation energy decreases with the increase of ion fluence indicates that the defect density of states increases.Also it was found that the value of dc conductivity and photoconductivity increases with the increase of ion fluence.

  8. Energy spread of ion beams generated in multicusp ion sources

    Energy Technology Data Exchange (ETDEWEB)

    Sarstedt, M.; Herz, P.; Kunkel, W.B. [and others

    1995-04-01

    For the production of future microelectronics devices, various alternate methods are currently being considered to replace the presently used method of lithography with ion beam lithography. One of these methods is the Ion Projection Lithography (IPL), which aims at the possibility of projecting sub-0.25 {mu}m patterns of a stencil mask onto a wafer substrate. In order to keep the chromatic aberrations below 25 nm, an ion source which delivers a beam with energy spread of less than 3 eV is desired. For this application, multicusp ion sources are being considered. We measure the longitudinal energy spread of the plasma ions by using a two-grid electrostatic energy analyzer. The energy spread of the extracted beam is measured by a high-voltage retarding-field energy analyzer. In order to obtain the transverse ion temperature, a parallel-plate scanner is being set up to study the beam emittance. In this paper, comparisons are made for different ion source configurations.

  9. Rare-earth-ion doped KY(WO4)2 optical waveguides grown by liquid-phase epitaxy

    NARCIS (Netherlands)

    Romanyuk, Y.E.; Apostolopoulos, V.; Utke, U.; Pollnau, Markus

    2004-01-01

    High-quality KY(WO4)2 thin layers doped with rare-earth-ions were grown using liquid-phase epitaxy. A low-temperature mixture of chlorides was used as the flux and undoped KY(WO4)2 crystals as substrates. The crystalline layers possessed thicknesses up to 10 µm. Passive and active planar waveguiding

  10. Optical and structural properties of InAs nanoclusters in crystalline Si obtained through sequential ion implantation and RTA

    Energy Technology Data Exchange (ETDEWEB)

    Sortica, Mauricio A.; Canut, Bruno; Chauvin, Nicolas [Institut des Nanotechnologies de Lyon INL-UMR5270, INSA - Lyon, CNRS, 7 av. Jean Capelle, 69621, Villeurbanne (France); Hatori, Masahiro; Dias, Johnny F. [Instituto de Fisica, Universidade Federal do Rio Grande do Sul IF-UFRGS, av. Bento Goncalves 9500, 91501-970, Porto Alegre - RS (Brazil); Marty, Olivier [Institut des Nanotechnologies de Lyon INL-UMR5270, Universite Claude Bernard Lyon 1, 8 rue Andre-Marie Ampere, 69622, Villeurbanne (France)

    2015-12-15

    Si (100) wafers were implanted at 500 C with 250 keV As ions and 350 keV In ions in this order. The implantations were carried out with three different fluences, namely 1 x 10{sup 16}, 2 x 10{sup 16}, and 5 x 10{sup 16} cm{sup -2}. The samples were annealed with rapid thermal annealing (RTA) for 30 s at temperatures ranging from 800 up to 1000 C. Different techniques like photoluminescence (PL) and Rutherford backscattering spectrometry (RBS) were employed to characterize the samples. Finally, scanning and transmission electron microscopy (SEM and TEM, respectively) provided further structural information of the InAs nanoclusters. The results indicate that InAs nanoprecipitates are formed after RTA treatment. Moreover, a broad photoluminescence peak was observed in all samples submitted to RTA. RBS results reveal that losses of implanted ions due to diffusion processes can be minimized through the use of RTA, depending of the fluence of ion implantation. Finally, the present results suggest that the photoluminescence yield depends on the degree of the radiation damage induced in the Si matrix during the implantation process. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  11. Au{sup 9+} swift heavy ion irradiation of Zn[CS(NH{sub 2}){sub 2}]{sub 3}SO{sub 4} crystal: Crystalline perfection and optical properties

    Energy Technology Data Exchange (ETDEWEB)

    Kushwaha, S.K., E-mail: kushwaha@princeton.edu [CSIR – National Physical Laboratory, Dr. K.S. Krishnan Road, New Delhi 110012 (India); Department of Chemistry, Princeton University, Princeton, NJ 08544 (United States); Maurya, K.K.; Vijayan, N.; Gupta, A.K.; Haranath, D. [CSIR – National Physical Laboratory, Dr. K.S. Krishnan Road, New Delhi 110012 (India); Kumar, B. [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India); Kanjilal, D. [Inter-University Accelerator Centre, New Delhi 110067 (India); Bhagavannarayana, G. [CSIR – National Physical Laboratory, Dr. K.S. Krishnan Road, New Delhi 110012 (India)

    2014-11-01

    Highlights: • Zn[CS(NH2){sub 2}]{sub 3}SO{sub 4}, a NLO crystal irradiated by Au{sup 9+} 150 MeV swift heavy ions. • Structural defects in pristine and irradiated crystals investigated and compared. • Functional groups and Raman lattice modes in crystal investigated. • Au{sup 9+} irradiation related PL emission, optical transparency and band gap studied. • Correlation of crystalline perfection with optical properties is discussed. - Abstract: The single crystal of tris(thiourea)zinc sulphate (Zn[CS(NH{sub 2}){sub 2}]{sub 3}SO{sub 4}) was irradiated by 150 MeV Au{sup 9+} swift heavy ions and analyzed in comparison with pure crystal for crystalline perfection and optical properties. The Fourier transform infrared and X-ray powder diffraction inferred that swift ions lead the disordering and breaking of molecular bonds in lattice without formation of new structural phases. High resolution X-ray diffraction (HRXRD) revealed the abundance of point defects, and formation of mosaics and low angle grain boundaries in the irradiated region of crystal. The swift ion irradiation found to affect the lattice vibrational modes and functional groups significantly. The defects induced by heavy ions act as the color centers and resulted in enhance of photoluminescence emission intensity. The optical transparency and band gap found to be decreased.

  12. Commissioning of an integrated platform for time-resolved treatment delivery in scanned ion beam therapy by means of optical motion monitoring.

    Science.gov (United States)

    Fattori, G; Saito, N; Seregni, M; Kaderka, R; Pella, A; Constantinescu, A; Riboldi, M; Steidl, P; Cerveri, P; Bert, C; Durante, M; Baroni, G

    2014-12-01

    The integrated use of optical technologies for patient monitoring is addressed in the framework of time-resolved treatment delivery for scanned ion beam therapy. A software application has been designed to provide the therapy control system (TCS) with a continuous geometrical feedback by processing the external surrogates tridimensional data, detected in real-time via optical tracking. Conventional procedures for phase-based respiratory phase detection were implemented, as well as the interface to patient specific correlation models, in order to estimate internal tumor motion from surface markers. In this paper, particular attention is dedicated to the quantification of time delays resulting from system integration and its compensation by means of polynomial interpolation in the time domain. Dedicated tests to assess the separate delay contributions due to optical signal processing, digital data transfer to the TCS and passive beam energy modulation actuation have been performed. We report the system technological commissioning activities reporting dose distribution errors in a phantom study, where the treatment of a lung lesion was simulated, with both lateral and range beam position compensation. The zero-delay systems integration with a specific active scanning delivery machine was achieved by tuning the amount of time prediction applied to lateral (14.61 ± 0.98 ms) and depth (34.1 ± 6.29 ms) beam position correction signals, featuring sub-millimeter accuracy in forward estimation. Direct optical target observation and motion phase (MPh) based tumor motion discretization strategies were tested, resulting in 20.3(2.3)% and 21.2(9.3)% median (IQR) percentual relative dose difference with respect to static irradiation, respectively. Results confirm the technical feasibility of the implemented strategy towards 4D treatment delivery, with negligible percentual dose deviations with respect to static irradiation.

  13. A comparison of two 40Ca+ single-ion optical frequency standards at the 5 × 10-17 level and an evaluation of systematic shifts

    Science.gov (United States)

    Huang, Y.; Guan, H.; Bian, W.; Ma, L.; Liang, K.; Li, T.; Gao, K.

    2017-05-01

    A comparison of two optical frequency standards and a detailed study of the systematic frequency shifts of each 40Ca+ single-ion optical frequency standard is presented. The methods used for the systematic shift evaluation of the comparison measurements are also provided. One of the ion traps runs at a chosen operating frequency of 24.7 MHz, determined by the differential scalar polarizability of the clock transition, at which frequency the rf-induced Stark shifts and second-order Doppler shifts cancel each other, yielding a great suppression in the combined micromotion shifts. After compensating for the micromotion, the two optical frequency standards both reach an uncertainty level of a few parts in 10-17, which is more than an order of magnitude smaller compared to a few years ago. The dominant source of uncertainty is the blackbody radiation shift after minimizing the micromotion-induced shifts. The blackbody radiation shift is evaluated by controlling and measuring the temperature at the trap center. With a measurement over one month, the frequency difference between the two clocks is measured to be 3.2 × 10-17 with a measurement uncertainty of 5.5 × 10-17, considering both the statistical (1.9 × 10-17) and the systematic (5.1 × 10-17) uncertainties. Due to improvement of the clock laser and better control of the optical and electromagnetic field geometry and the laboratory conditions, a fractional stability of 7 × 10-17 in 20,000 s of averaging time is achieved. The absolute frequency of the 40Ca+ 4 s2S1/2-3d 2D5/2 clock transition is measured as 411 042 129 776 401.7 (1.1) Hz, with a fractional uncertainty of 2.7 × 10-15 using the GPS satellites as a link to the SI second. Details of the method used for the systematic shift evaluation of the measurements are given.

  14. Electron paramagnetic resonance and optical spectroscopy of Yb sup 3 sup + ions in SrF sub 2 and BaF sub 2; an analysis of distortions of the crystal lattice near Yb sup 3 sup +

    CERN Document Server

    Falin, M L; Latypov, V A; Leushin, A M

    2003-01-01

    SrF sub 2 and BaF sub 2 crystals, doped with the Yb sup 3 sup + ions, have been investigated by electron paramagnetic resonance and optical spectroscopy. As-grown crystals of SrF sub 2 and BaF sub 2 show the two paramagnetic centres for the cubic (T sub c) and trigonal (T sub 4) symmetries of the Yb sup 3 sup + ions. Empirical diagrams of the energy levels were established and the potentials of the crystal field were determined. Information was obtained on the SrF sub 2 and BaF sub 2 phonon spectra from the electron-vibrational structure of the optical spectra. The crystal field parameters were used to analyse the crystal lattice distortions in the vicinity of the impurity ion and the F sup - ion compensating for the excess positive charge in T sub 4. Within the frames of a superposition model, it is shown that three F sup - ions from the nearest surrounding cube, located symmetrically with respect to the C sub 3 axis from the side of the ion-compensator, approach the impurity ion and cling to the axis of the...

  15. Optical characterization of perovskite, KMgF{sub 3}, optically activated with trivalent lanthanides ions; Caracterizacion optica de la perovskita, KMgF{sub 3}, activada opticamente con iones lantanidos trivalentes

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez, F.J.; Sosa, A.; Sosa, R.; Azorin, J. [Depto. de Fisica, Universidad Autonoma Metropolitana-Iztapalapa, 09340 Mexico D.F. (Mexico); Furetta, C. [Dip. di Fisica, UR, 00185, Roma (Italy)

    2002-07-01

    During the last years, it has been shown that the perovskite has a great potential in its application as thermoluminescent dosemeter. With the purpose of reaching wide knowledge of this material, in this work, a study of the absorption, emission and excitation spectra is presented, all they characteristic of crystalline samples of KMgF{sub 3} which are doped with different trivalent lanthanides ions; Lu, Ho, Tm and Tb. Also, the measurements of the emission decay times are presented, which are obtained with laser spectroscopy techniques of solved times. (Author)

  16. Optical and photovoltaic properties of zinc sulfide quantum dots fabricated by spin-assisted successive ion layer adsorption and reaction technique

    Science.gov (United States)

    Mehrabian, Masood; Mirabbaszadeh, Kavoos; Afarideh, Hossein; Kim, Yoon Sang

    2014-01-01

    Zinc sulfide (ZnS) quantum dots were prepared by successive ion layer adsorption and reaction (SILAR) technique based on spin coating (spin-SILAR). The effect of the number of SILAR cycle (n) on optical and photovoltaic properties was studied. An optimized ZnS quantum dot sensitized solar cell demonstrated maximum power conversion efficiency of 3.58% with a short-circuit current of 10.53 mA/cm2 and an open-circuit voltage of 0.58 V under one sun illumination (AM1.5). The results showed that a ZnS QD layer with n=10 (thickness ˜80 nm) can be used as a highly efficient sensitizer for solar cells. The ZnS QD layer acts as a light absorber and a recombination blocking layer in the ITO/ZnO film/ZnS QD/P3HT/PCBM/Ag structure.

  17. Simultaneous measurement of temperature and refractive index using focused ion beam milled Fabry-Perot cavities in optical fiber micro-tips.

    Science.gov (United States)

    André, Ricardo M; Warren-Smith, Stephen C; Becker, Martin; Dellith, Jan; Rothhardt, Manfred; Zibaii, M I; Latifi, H; Marques, Manuel B; Bartelt, Hartmut; Frazão, Orlando

    2016-06-27

    Optical fiber micro-tips are promising devices for sensing applications in small volume and difficult to access locations, such as biological and biomedical settings. The tapered fiber tips are prepared by dynamic chemical etching, reducing the size from 125 μm to just a few μm. Focused ion beam milling is then used to create cavity structures on the tapered fiber tips. Two different Fabry-Perot micro-cavities have been prepared and characterized: a solid silica cavity created by milling two thin slots and a gap cavity. A third multi-cavity structure is fabricated by combining the concepts of solid silica cavity and gap cavity. This micro-tip structure is analyzed using a fast Fourier transform method to demultiplex the signals of each cavity. Simultaneous measurement of temperature and external refractive index is then demonstrated, presenting sensitivities of - 15.8 pm/K and -1316 nm/RIU, respectively.

  18. Applications of vitamin B6 cofactor pyridoxal 5‧-phosphate and pyridoxal 5‧-phosphate crowned gold nanoparticles for optical sensing of metal ions

    Science.gov (United States)

    Bothra, Shilpa; Upadhyay, Yachana; Kumar, Rajender; Sahoo, Suban K.

    2017-03-01

    Vitamin B6 cofactor pyridoxal 5‧-phosphate (PLP) and PLP crowned gold nanoparticles (PLP-AuNPs) was applied for the optical chemosensing of metal ions in aqueous medium. PLP showed a visually detectable colour change from colourless to yellow and 'turn-off' fluorescence in the presence of Fe3 +. The fluorescence intensity of PLP at 433 nm was also blue-shifted and enhanced at 395 nm upon addition of Al3 +. When the PLP was functionalized over AuNPs surface, the wine red colour of PLP-AuNPs was turned to purplish-blue and the SPR band at 525 nm was red-shifted upon addition of Al3 +, Cd2 + and Pb2 + due to the complexation-induced aggregation of nanoparticles. The developed sensing systems exhibited good selectivity and specificity for the detected analytes (Fe3 +, Al3 +, Cd2 + and Pb2 +).

  19. Optical Mixing Controlled Stimulated Scattering instabilities: Suppression of SRS by the Controlled Introduction of Ion Acoustic and Electron Plasma Wave Turbulence

    CERN Document Server

    Afeyan, Bedros; Won, K; Montgomery, D S; Hammer, J; Kirkwood, R K; Schmitt, A J

    2012-01-01

    In a series of experiments on the Omega laser facility at LLE, we have demonstrated the suppression of SRS in prescribed spectral windows due to the presence of externally controlled levels of ion acoustic waves (IAW, by crossing two blue beams at the Mach -1 surface) and electron plasma waves (EPW, by crossing a blue and a green beam around a tenth critical density plasma) generated via optical mixing. We have further observed SRS backscattering of a green beam when crossed with a blue pump beam, in whose absence, that (green beam) backscattering signature was five times smaller. This is direct evidence for green beam amplification when crossed with the blue. Additional proof comes from transmitted green beam measurements. A combination of these techniques may allow the suppression of unacceptable levels of SRS near the light entrance hole of large-scale hohlraums on the NIF or LMJ.

  20. Cu2ZnSnS4 thin films prepared by sulfurization of ion beam sputtered precursor and their electrical and optical properties

    Institute of Scientific and Technical Information of China (English)

    ZHANG Jun; SHAO Lexi; FU Yujun; XIE Erqing

    2006-01-01

    Cu2ZnSnS4 (CZTS) thin films were successfully prepared by sulfurization of ion bean sputtered precursors on soda-lime glass substrate. The single phase of stannite-type structure CZTS films were obtained as revealed in EDS and XRD analysis when the ratios of the constituents of CZTS thin films are close to stoichiometric by optimizing the conditions of precursor preparation and sulfurization. A low sheet resistivity as about 0.156 Ω·cm and a high absorption coefficient as 1×104 cm-1 were achieved in this method by Hall effect measurements and UV-VIS spectrophotometer. The optical band-gap energy of the CZTS sample is about 1.51 eV, which is very close to the optimum value for a solar-cell absorber.

  1. Structural and optical properties of silicon layers with InSb and InAs nanocrystals formed by ion-beam synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Komarov, F.; Vlasukova, L.; Greben, M.; Milchanin, O. [Belarusian State University, Independence Ave. 4, 220030 Minsk (Belarus); Zuk, J., E-mail: jotzet@hektor.umcs.lublin.pl [Maria Curie-Skłodowska University, Pl. M. Curie-Skłodowskiej 1, 20-031 Lublin (Poland); Wesch, W.; Wendler, E. [Institut für Festkörperphysik, Friedrich-Schiller-Universität Jena, Max-Wien-Platz 1, D-07743 Jena (Germany); Togambaeva, A. [Al-Farabi Kazakh National University, 71 Al-Farabi Ave., 050040 Almaty (Kazakhstan)

    2013-07-15

    We have studied the formation of InSb and InAs precipitates with sizes of several nanometers in Si and SiO{sub 2}/Si by means of implantation of (Sb + In) or (As + In) ions with energies from 170 to 350 keV and fluencies from 2.8 to 3.5 × 10{sup 16} cm{sup −2} at 500 °C and subsequent annealing at 1050–1100 °C for 3–30 min. RBS, TEM/TED, RS and PL techniques were employed to characterize the implanted layers. A broad band in the region of 1.2–1.6 μm has been registered in the low-temperature PL spectra of both (Sb + In) and (As + In) implanted and annealed silicon crystals. It was shown that structural and optical properties of oxidized silicon crystals strongly depend on type of implanted species in silicon crystals.

  2. Towards simultaneous achievement of carrier activation and crystallinity in Ge and GeSn with heated phosphorus ion implantation: An optical study

    Science.gov (United States)

    D'Costa, Vijay Richard; Wang, Lanxiang; Wang, Wei; Lim, Sin Leng; Chan, Taw Kuei; Chua, Lye Hing; Henry, Todd; Zou, Wei; Hatem, Christopher; Osipowicz, Thomas; Tok, Eng Soon; Yeo, Yee-Chia

    2014-09-01

    We have investigated the optical properties of Ge and GeSn alloys implanted with phosphorus ions at 400 °C by spectroscopic ellipsometry from far-infrared to ultraviolet. The dielectric response of heated GeSn implants displays structural and transport properties similar to those of heated Ge implants. The far-infrared dielectric function of as-implanted Ge and GeSn shows the typical free carrier response which can be described by a single Drude oscillator. Bulk Ge-like critical points E1, E1 + Δ1, E0', and E2 are observed in the visible-UV dielectric function of heated Ge and GeSn indicating single crystalline quality of the as-implanted layers. Although the implantation at 400 °C recovers crystallinity in both Ge and GeSn, an annealing step is necessary to enhance the carrier activation.

  3. Optical properties of Mn3+ ions in Cs2NaAlF6 and Cs2NaGaF6 single crystals

    Science.gov (United States)

    da Fonseca, R. J. M.; Sosman, L. P.; Camara, A. R.

    2017-02-01

    The optical properties of Mn3+ ions in the elpasolites Cs2NaGaF6 and Cs2NaAlF6 have been investigated by absorption spectroscopy at 4.2 K. The absorption spectra are dominated by the spin-allowed 5E → 5T2 transition and the transition between the two Jahn-Teller components of the 5E level. The crystal-field parameter Dq was determined and a low crystal-field situation was established for both Mn3+-doped fluorides. The Jahn-Teller stabilization energies of the 5E and 5T2 levels were calculated and the obtained values shown a strong Jahn-Teller splitting in the 5E ground state.

  4. Characterization of ion accelerating systems on NASA LeRC's ion thrusters

    Science.gov (United States)

    Rawlin, Vincent K.

    1992-01-01

    An investigation is conducted regarding ion-accelerating systems for two NASA thrusters to study the limits of ion-extraction capability or perveance. A total of nine two-grid ion-accelerating systems are tested with the 30- and 50-cm-diam ring-cusp inert-gas ion thrusters emphasizing the extension of ion-extraction. The vacuum-tank testing is described using xenon, krypton, and argon propellants, and thruster performance is computed with attention given to theoretical design considerations. Reductions in perveance are noted with decreasing accelerator-hole-to-screen-hole diameter ratios. Perveance values vary indirectly with the ratio of discharge voltage to total accelerating voltage, and screen/accelerator electrode hole-pair alignment is also found to contribute to perveance values.

  5. Study of vibrational spectroscopy, linear and non-linear optical properties of Sm3+ ions doped BaO-ZnO-B2O3 glasses

    Science.gov (United States)

    Nanda, Kirti; Kundu, R. S.; Sharma, Sarita; Mohan, Devendra; Punia, R.; Kishore, N.

    2015-07-01

    Samarium oxide doped Barium-Zinc-Borate glasses with compositions xSm2O3-(100-x)[0.1BaO-0.4ZnO-0.5B2O3]; x = 0.0, 0.5, 1.0, 1.5 and 2.0 have been prepared by melt quench technique. The amorphous nature of as-prepared glasses has been ascertained by X-ray diffraction patterns. The observed values of density and molar volume of the glass samples are found to increase with the increase in concentration of Sm2O3. Fourier Transform Infrared spectra of the prepared glasses indicate that Sm2O3 acts as glass modifier. With the increase in Sm2O3 content, BO4 structural units start converting into BO3 structural units. The values of optical energy band gap (Eg), estimated from Tauc's plots, are observed to decrease with the increase in Sm2O3 content. The nonlinear optical properties of glass samples have been investigated by Z-scan method with nanosecond pulsed laser at ˜532 nm in both open and close aperture geometries. The values of two photon absorption coefficient (β) and nonlinear refractive index (n2) have been estimated by fitting of experimentally observed data with theoretical models and both are found to increase with the increase in Sm3+ ions concentration in the glass matrix. The total third order nonlinear susceptibility (χ(3)) have been calculated and observed to increase with the increase in Sm3+ ions concentration.

  6. Raman, FTIR, DSC, EPR and optical properties of B2O3-K2O-ZnO-Li2Oglass system doped with Cu2+ ions

    Directory of Open Access Journals (Sweden)

    G. N. Devde

    2015-12-01

    Full Text Available X-ray diffraction (XRD, Raman, Fourier Transform Infrared (FTIR, Differential scanning calorimetry (DSC, Electron paramagnetic resonance (EPR and optical absorption studies on 59B2O3-10K2O-(30-xZnO-xLi2O- 1CuO glasses (where x = 0, 6, 12, 18, 24 and 30 mol% have been carried out. The amorphous nature of the glasses was confirmed using XRD and DSC measurements. The glass transition temperature (Tg of glass samples have been estimated from DSC traces and found that Tg decreases from 488 to 422 oC with the progressive substitution of Li2O content in the place of ZnO content. Almost all of the glass samples in the composition 59B2O3-10K2O-(30-xZnO-xLi2O-1CuO (0 ≤ x ≤ 30 mol% have the thermal stability (ΔT more than 100 oC. The Raman and FTIR studies have been showed that the present glass system consists of [BO3] and [BO4] units in various borate groups. The spin-Hamiltonian parameters (SHP such as g||, g⊥, and A|| have been determined from EPR spectra and it was found that the Cu2+ ion is present in tetragonal distorted octahedral site with x2 - y2 d as the ground state. Bonding parameters and bonding symmetry of Cu2+ ions have been calculated by correlating EPR and optical data and were found to be composition dependent.

  7. Effects of swift heavy ion irradiation on structural, optical and photocatalytic properties of ZnO–CuO nanocomposites prepared by carbothermal evaporation method

    Directory of Open Access Journals (Sweden)

    Sini Kuriakose

    2015-04-01

    Full Text Available ZnO–CuO nanocomposite thin films were prepared by carbothermal evaporation of ZnO and Cu, combined with annealing. The effects of 90 MeV Ni7+ ion irradiation on the structural and optical properties of ZnO–CuO nanocomposites were studied by using X-ray diffraction (XRD, field emission scanning electron microscopy (FESEM, UV–visible absorption spectroscopy and Raman spectroscopy. XRD studies showed the presence of ZnO and CuO nanostructures in the nanocomposites. FESEM images revealed the presence of nanosheets and nanorods in the nanocomposites. The photocatalytic activity of ZnO–CuO nanocomposites was evaluated on the basis of degradation of methylene blue (MB and methyl orange (MO dyes under sun light irradiation and it was observed that swift heavy ion irradiation results in significant enhancement in the photocatalytic efficiency of ZnO–CuO nanocomposites towards degradation of MB and MO dyes. The possible mechanism for the enhanced photocatalytic activity of ZnO–CuO nanocomposites is proposed. We attribute the observed enhanced photocatalytic activity of ZnO–CuO nanocomposites to the combined effects of improved sun light utilization and suppression of the recombination of photogenerated charge carriers in ZnO–CuO nanocomposites.

  8. Effects of swift heavy ion irradiation on structural, optical and photocatalytic properties of ZnO-CuO nanocomposites prepared by carbothermal evaporation method.

    Science.gov (United States)

    Kuriakose, Sini; Avasthi, D K; Mohapatra, Satyabrata

    2015-01-01

    ZnO-CuO nanocomposite thin films were prepared by carbothermal evaporation of ZnO and Cu, combined with annealing. The effects of 90 MeV Ni(7+) ion irradiation on the structural and optical properties of ZnO-CuO nanocomposites were studied by using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), UV-visible absorption spectroscopy and Raman spectroscopy. XRD studies showed the presence of ZnO and CuO nanostructures in the nanocomposites. FESEM images revealed the presence of nanosheets and nanorods in the nanocomposites. The photocatalytic activity of ZnO-CuO nanocomposites was evaluated on the basis of degradation of methylene blue (MB) and methyl orange (MO) dyes under sun light irradiation and it was observed that swift heavy ion irradiation results in significant enhancement in the photocatalytic efficiency of ZnO-CuO nanocomposites towards degradation of MB and MO dyes. The possible mechanism for the enhanced photocatalytic activity of ZnO-CuO nanocomposites is proposed. We attribute the observed enhanced photocatalytic activity of ZnO-CuO nanocomposites to the combined effects of improved sun light utilization and suppression of the recombination of photogenerated charge carriers in ZnO-CuO nanocomposites.

  9. Rapid and effective synthesis of $\\text{}^{40}\\text{Ca}-\\text{}^{27}\\text{Al}$ ion pair towards quantum logic optical clock

    CERN Document Server

    Shang, Junjuan; Cao, Jian; Wang, Shaomao; Shu, Hualin; Huang, Xueren

    2016-01-01

    High precision atomic clocks have been applied not only to very important technological problems such as synchronization and global navigation systems, but to the fundament precision measurement physics. Single $\\text{}^{27}\\text{Al}^+$ is one of the most attractions of selection system due to its very low blackbody radiation effect which dominates frequency shifts in other optical clock systems. Up to now, the $\\text{}^{27}\\text{Al}^+$ still could not be laser-cooled directly by reason that the absence of 167nm laser. Sympathetic cooling is a viable method to solve this problem. In this work, we used a single laser cooled $\\text{}^{40}\\text{Ca}^+$ to sympathetically cool one $\\text{}^{27}\\text{Al}^+$ in linear Paul trap. Comparing to laser ablation method we got a much lower velocity atoms sprayed from a home-made atom oven, which would make loading aluminum ion more efficient and the sympathetic cooling much easier. By the method of precisely measuring the secular frequency of the ion pair, finally we prove...

  10. Effects of phosphorus doping by plasma immersion ion implantation on the structural and optical characteristics of Zn0.85Mg0.15O thin films

    Science.gov (United States)

    Saha, S.; Nagar, S.; Chakrabarti, S.

    2014-08-01

    ZnMgO thin films deposited on Si substrates by RF sputtering were annealed at 800, 900, and 1000 °C after phosphorus plasma immersion ion implantation. X-ray diffraction spectra confirmed the presence of and peaks for all the samples. However, in case of the annealed samples, the peak was also observed. Scanning electron microscopy images revealed the variation in surface morphology caused by phosphorus implantation. Implanted and non-implanted samples were compared to examine the effects of phosphorus implantation on the optical properties of ZnMgO. Optical characteristics were investigated by low-temperature (15 K) photoluminescence experiments. Inelastic exciton-exciton scattering and localized, and delocalized excitonic peaks appeared at 3.377, 3.42, and 3.45 eV, respectively, revealing the excitonic effect resulting from phosphorus implantation. This result is important because inelastic exciton-exciton scattering leads to nonlinear emission, which can improve the performance of many optoelectronic devices.

  11. Er{sup 3+} ions doped tellurite glasses with high thermal stability, elasticity, absorption intensity, emission cross section and their optical application

    Energy Technology Data Exchange (ETDEWEB)

    Yousef, El Sayed, E-mail: omn_yousef2000@yahoo.com [Physics Dep., Faculty of Science, King Khalid University, P.O. Box 9003, Abha (Saudi Arabia); Physics Dep., Faculty of Science, Al-Azhar University, Assiut Branch, Assiut (Egypt)

    2013-06-05

    Highlights: ► Present glasses have high thermal stability. ► The glass sample C has the effective emission cross section bandwidth (64 nm). It has large stimulated emission cross-section (0.89 × 10{sup −20} cm{sup 2}). ► The optical gain coefficient to the population inversion of the {sup 4}I{sub 13/2} level is 8.87 cm{sup −1}. -- Abstract: Three samples of tellurite glasses within system 46TeO{sub 2}⋅15ZnO⋅9.0P{sub 2}O{sub 5}⋅30LiNbO{sub 3} doped with xEr{sub 2}O{sub 3} ions (where x = 4000, 8000 and 10,000 ppm) have been prepared by using the conventional melt-quenching method. These glasses have high thermal stability proved by using differential thermal analysis (DTA) measurements. Elastic properties of the glasses were investigated by measuring both longitudinal and shear velocities using the pulse-echo overlap technique at 5 MHz. Elastic moduli such as: longitudinal (λ), shear (μ), Bulk (B) and Young’s (Y) increased with the Er{sup 3+} concentration in the prepared glasses matrix. The optical properties of the glasses were estimated by measuring UV–vis-NIR spectroscopy. The Judd–Ofelt parameters, Ω{sub t} (t = 2, 4, 6) of Er{sup 3+} were evaluated from optical absorption spectra. The oscillator strength type transition probabilities, spectroscopic quality factors, branching ratio and radiative lifetimes of several excited states of Er{sup 3+} have been predicted using intensity Judd–Ofelt parameters. Gain cross-section for the Er{sup 3+} laser transition {sup 4}I{sub 13/2} → {sup 4}I{sub 15/2} was obtained. The results show 46TeO{sub 2}⋅15ZnO⋅9.0P{sub 2}O{sub 5}⋅30LiNbO{sub 3}⋅10,000 ppm Er{sub 2}O{sub 3} glass has the effective emission cross section bandwidth (64 nm) and large stimulated emission cross-section (0.89 × 10{sup −20} cm{sup 2}). The thermal stability, elastic and spectroscopic properties indicate that this glass doped with Er{sup 3+} is a promising candidate for optical applications and may be suitable

  12. Collisional Ionization Equilibrium for Optically Thin Plasmas. I. Updated Recombination Rate Coefficients for Bare though Sodium-like Ions

    CERN Document Server

    Bryans, P; Gorczyca, T W; Laming, J M; Mitthumsiri, W; Savin, D W

    2006-01-01

    Reliably interpreting spectra from electron-ionized cosmic plasmas requires accurate ionization balance calculations for the plasma in question. However, much of the atomic data needed for these calculations have not been generated using modern theoretical methods and are often highly suspect. This translates directly into the reliability of the collisional ionization equilibrium (CIE) calculations. We make use of state-of-the-art calculations of dielectronic recombination (DR) rate coefficients for the hydrogenic through Na-like ions of all elements from He up to and including Zn. We also make use of state-of-the-art radiative recombination (RR) rate coefficient calculations for the bare through Na-like ions of all elements from H through to Zn. Here we present improved CIE calculations for temperatures from $10^4$ to $10^9$ K using our data and the recommended electron impact ionization data of \\citet{Mazz98a} for elements up to and including Ni and Mazzotta (private communication) for Cu and Zn. DR and RR ...

  13. Theoretical investigation of the optical and EPR parameters for VO{sup 2+}ion in some complexes

    Energy Technology Data Exchange (ETDEWEB)

    Kalfaoglu, Emel [OndokuzMay Latin-Small-Letter-Dotless-I s University, Faculty of Sciences, Department of Physics, 55139 Kurupelit-Samsun (Turkey); Karabulut, Buenyamin, E-mail: bbulut@omu.edu.tr [OndokuzMay Latin-Small-Letter-Dotless-I s University, Faculty of Sciences, Department of Physics, 55139 Kurupelit-Samsun (Turkey)

    2012-04-15

    The molecular orbital coefficients and the EPR parameters of trisodium citrate dihydrate, sodium hydrogen oxalate monohydrate, potassium d-gluconate monohydrate and L-Alanine vanadyl complexes are calculated theoretically. Two d-d transition spectra and EPR parameters for the VO{sup 2+} complex are calculated theoretically by using crystal-field theory. The calculated g and A paramaters have indicated that paramagnetic center is axially symmetric. Having the relations of g{sub Parallel-To } Left-Pointing-Angle-Bracket g{sub Up-Tack } Left-Pointing-Angle-Bracket g{sub e} and A{sub Parallel-To } Right-Pointing-Angle-Bracket A{sub Up-Tack} for VO{sup 2+} ions, it can be concluded that VO{sup 2+} ions are located in distorted octahedral sites (C{sub 4v}) elongated along the z-axis and the ground state of the paramagnetic electron is d{sub xy}. - Highlights: Black-Right-Pointing-Pointer The EPR parameters and molecular orbital coefficients are calculated theoretically. Black-Right-Pointing-Pointer The g and A values of all complexes are found to be nearly axially symmetric. Black-Right-Pointing-Pointer The ground state of the paramagnetic electron is d{sub xy.}.

  14. Ion beam figuring technique used as final step in the manufacturing of the optics for the E-ELT

    Science.gov (United States)

    Ghigo, M.; Vecchi, G.; Basso, S.; Citterio, O.; Civitani, M.; Pareschi, G.; Sironi, G.

    The INAF-Astronomical Observatory of Brera (INAF-OAB) is exploring the technical problems related to the ion beam figuring (IBF) of the Zerodur hexagonal mirrors (1.45 m corner to corner) of M1 for the European Extremely Large Telescope (E-ELT). As starting step a scaled down version mirror of the same material having size of 1 m corner to corner has been used to assess the relevant figuring problems. This specific mirror is spherical and has a radius of curvature of 3 m which allows a simple interferometric measurement setup. A mechanical support was designed to minimize its deformations due to gravity. The Ion Beam Figuring Facility used for this study has been recently completed in the Brera Observatory and has a figuring area of 170 cm x 140 cm. Aim of this study is the estimation and optimization of the time requested for the correction of the surface using also strategies to control the well-known thermal problems related to the Zerodur material. In this paper we report the results obtained figuring the 1 m corner-to-corner test segment.

  15. Metal ion coordination in `R’ and `T’ state hybrid hemoglobins as revealed by optical, EPR and sulphhydryl reactivity studies

    Indian Academy of Sciences (India)

    S Ramasamy; Swarnalatha Venkateshrao; J M Rifkind; P T Manoharan

    2005-03-01

    The sulphhydryl environment in various mixed-metal hybrid hemoglobins, viz. 2(Cu)-2(FeCO), 2(FeCO)-2(Cu), 2(Cu)-2(Ni), 2(Ni)-2(Cu), was studied by reacting them with the sulphhydryl reagent, 4,4'-dithiodipyridine (4-PDS). The reactivity was compared with that of HbCO, NiHb and CuHb. It is found that there exists a correlation between conformational change and metal ion environment, not only at the extreme R and T states but also the intermediate conformations. EPR examinations of these hybrids show that both in 4R state-[Cu(II)-Fe(II)] and state-[Cu(II)-Ni(II)] hybrids at neutral pH and in the absence of IHP, CuPPIX, irrespective of the subunit in which it is present, has a mixed-metal ion environment: Species 1, a five-coordinated Cu2+ complex with strong proximal histidine bond and species 2, a four-coordinated complex without any covalent linkage with N F8-histidine.

  16. The influence of Ag{sup 9+} ion irradiation on the structural, optical and luminescence properties of Sm{sup 3+} doped NaSrBO{sub 3}: Stability of color emission

    Energy Technology Data Exchange (ETDEWEB)

    Bedyal, A.K. [School of Physics, Shri Mata Vaishno Devi University, Katra 182320 - J& K (India); Kumar, Vinay, E-mail: vinaykumar@smvdu.ac.in [School of Physics, Shri Mata Vaishno Devi University, Katra 182320 -J& K (India); Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA 9300 (South Africa); Singh, Vivek K. [School of Physics, Shri Mata Vaishno Devi University, Katra 182320 - J& K (India); Singh, Fouran; Lochab, S.P. [Inter University Accelerator Centre, Anura Asaf Ali Marg, P.O. Box 10502, New Delhi 110067 (India); Ntwaeaborwa, O.M.; Swart, H.C. [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA 9300 (South Africa)

    2015-05-15

    Highlights: •120 MeV Ag{sup 9+} ion irradiation modified the structure, optical and luminescence properties of NaSrBO{sub 3}: Sm{sup 3+} phosphor. •The phosphor is synthesized by the solid state reaction and combustion method. •Colour statibilty confirmed by CIE coordinates after ion irradiations. -- Abstract: This paper reports on the effect of 120 MeV Ag{sup 9+} ion irradiation on the structure, optical and luminescence properties of NaSr{sub 1−x}BO{sub 3}: xSm{sup 3+} (x = 0.5–2.5 mol.%) phosphor, synthesized by the solid state reaction and combustion method. The samples were irradiated with Ag{sup 9+} swift heavy ions (SHIs) using fluences of 1 × 10{sup 12} ions cm{sup −2}, 5 × 10{sup 12} ions cm{sup −2} and 1 × 10{sup 13} ions cm{sup −2}. The as-prepared as well as irradiated samples were characterized by X-ray diffraction (XRD), diffuse reflectance (DR) and photoluminescence (PL) techniques. After irradiation, the structure of the phosphor did not change except that the loss of crystallinity which may be due to the fragmentation caused by the SHI. DR spectra reflect a blue shift in the absorption band with increasing fluences, for phosphors prepared using both solid state reaction and combustion method, resulting in an increase in the band gap from 5.64 to 6.06 eV. The PL intensity of the phosphors was enhanced with an increase in ion fluences, with the samples prepared using a combustion method exhibiting prominent intensity. The CIE coordinates were calculated and they correspond to the shade of orange–red emission of the Sm{sup 3+} ions.

  17. Hybrid magneto-optical mode converter made with a magnetic nanoparticles-doped SiO2/ZrO2 layer coated on an ion-exchanged glass waveguide

    Science.gov (United States)

    Amata, Hadi; Royer, François; Choueikani, Fadi; Jamon, Damien; Parsy, François; Broquin, Jean-Emmanuel; Neveu, Sophie; Jacques Rousseau, Jean

    2011-12-01

    This paper describes the possibility to achieve a TE-TM mode conversion in a magneto-optical hybrid waveguide operating at λ = 1550 nm. This hybrid device is made by coating a SiO2/ZrO2 layer doped with magnetic nanoparticles on an ion-exchanged glass waveguide. Soft annealing (90 °C) and UV treatment, both compatible with the ion exchange process, have been implemented to finalize the magneto-optical film. Optical characterizations that have been carried out demonstrated the efficiency of these hybrid structures in terms of lateral confinement and mode conversion. Indeed, TE to TM mode conversion has been observed when a longitudinal magnetic field is applied to the device. The amount of this conversion is discussed taking into account the distribution of light between the layer and the guide, and the modal birefringence of the structure.

  18. Design and characterisation of a real time proton and carbon ion radiography system based on scintillating optical fibres.

    Science.gov (United States)

    Lo Presti, D; Bonanno, D L; Longhitano, F; Bongiovanni, D G; Russo, G V; Leonora, E; Randazzo, N; Reito, S; Sipala, V; Gallo, G

    2016-09-01

    This paper describes the design and characterization of a charged particle imaging system composed of a position sensitive detector and residual range detector. The position detector consists of two identical overlying and orthogonal planes each of which consists of two layers of pre-aligned and juxtaposed scintillating fibres. The 500μm square section fibres are optically coupled to two Silicon Photomultiplier arrays using a channel reduction system patented by the Istituto Nazionale di Fisica Nucleare. The residual range detector consists of sixty parallel layers of the same fibres used in the position detector each of which is optically coupled to a Silicon Photomultiplier array by wavelength shifting fibres. The sensitive area of the two detectors is 9×9cm(2). Characterising the position sensitive and the residual range detectors to reconstruct the radiography, is fundamental to validating the detectors' designs. The proton radiography of a calibrated target in imaging conditions is presented. The spatial resolution of the position sensitive detector is about 150μm and the range resolution is about 170μm. The performance of the prototypes were tested at CATANA proton therapy facility (Laboratori Nazionali del Sud, INFN, Catania) with energy up to 58MeV and rate of about 10(6) particles per second. The comparison between the simulations and measurements confirms the validity of this system. Copyright © 2016 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

  19. Thermal and optical properties of Nd3+ doped lead zinc borate glasses—Influence of alkali metal ions

    Science.gov (United States)

    Sasi Kumar, M. V.; Rajesh, D.; Balakrishna, A.; Ratnakaram, Y. C.

    2013-04-01

    In the present investigation a new series of six different Nd3+ doped alkali and mixed alkali (Li, Na, K, Li-Na, Li-K and Na-K) heavy metal (PbO and ZnO) borate glasses were prepared using the melt quenching technique. The amorphous nature of the glass systems has been identified based on the X-ray diffraction analysis. The glass transition studies were carried out using differential scanning calorimetry (DSC). Optical properties were studied by measuring the optical absorption and near infrared luminescence spectra. The Judd-Ofelt (J-O) theory has been applied to calculate J-O intensity parameters, Ωλ (λ=2, 4 and 6) and in turn used to estimate radiative properties of certain transitions. Spectroscopic parameters such as transition probabilities (AT), branching ratios (β), radiative lifetimes (τR) and integrated absorption cross-sections (Σ) were calculated using J-O intensity parameters for all transitions. Using emission spectra, experimental branching ratios and stimulated emission cross-sections (σP) are obtained for all the observed emission transitions.

  20. Thermal and optical properties of Nd{sup 3+} doped lead zinc borate glasses—Influence of alkali metal ions

    Energy Technology Data Exchange (ETDEWEB)

    Sasi Kumar, M.V.; Rajesh, D.; Balakrishna, A. [Department of Physics, Sri Venkateswara University, Tirupati 517502 (India); Ratnakaram, Y.C., E-mail: ratnakaramsvu@gmail.com [Department of Physics, Sri Venkateswara University, Tirupati 517502 (India)

    2013-04-15

    In the present investigation a new series of six different Nd{sup 3+} doped alkali and mixed alkali (Li, Na, K, Li–Na, Li–K and Na–K) heavy metal (PbO and ZnO) borate glasses were prepared using the melt quenching technique. The amorphous nature of the glass systems has been identified based on the X-ray diffraction analysis. The glass transition studies were carried out using differential scanning calorimetry (DSC). Optical properties were studied by measuring the optical absorption and near infrared luminescence spectra. The Judd–Ofelt (J–O) theory has been applied to calculate J–O intensity parameters, Ω{sub λ} (λ=2, 4 and 6) and in turn used to estimate radiative properties of certain transitions. Spectroscopic parameters such as transition probabilities (A{sub T}), branching ratios (β), radiative lifetimes (τ{sub R}) and integrated absorption cross-sections (Σ) were calculated using J–O intensity parameters for all transitions. Using emission spectra, experimental branching ratios and stimulated emission cross-sections (σ{sub P}) are obtained for all the observed emission transitions.

  1. Studies of the optical spectra and spin-Hamiltonian parameters for the trivalent ytterbium ions in lithium yttrium fluoride crystals

    Science.gov (United States)

    Feng, W. L.; Han, Z.; Zhong, Y. C.

    In this paper, the crystal field (CF) levels and spin-Hamiltonian (SH) parameters (g factors g∥ and g⊥ and hyperfine structure constants A∥ and A⊥) of the rare-earth ion Yb3+ in lithium yttrium fluoride crystals are calculated under D2d point symmetry assumption. Two main methods are used in the calculation to study the SH parameters: one is the perturbation theory method and the other is the complete diagonalization (energy matrix) method (CDM). Comparing the calculated results with the experimental data, we can see that the CDM is more effective to calculate the SH parameters. In addition, the CF J-mixing of all excited-state multiplets into the ground-state multiplet 2F7/2 is considered. The validity of the calculated results is discussed.

  2. Optical detection of ion diffusion in electrochromic poly(3,4-ethylenedioxy)thiophene film using microcantilever electrodes

    DEFF Research Database (Denmark)

    Lin, Rong; Stokbro, Kurt; Madsen, Dorte Nørgaard;

    2005-01-01

    potential of the film induced dark (light-absorbing) rings, which spread out from the anode on a time scale of seconds. The rate of expansion of the rings as well as the final diameter depended on the bias voltage. Using two micro four-point probes simultaneously, we measured with one probe the conductance......We present measurements of microscale electrochromic switching of poly(3,4-ethylenedioxy)thiophene doped with poly(4-styrene sulfonate), thin film using microfabricated multi-point probe electrodes. After treatment with a dilute hydrochloric acid, a voltage bias above 3 V with respect to the ground...... of the film outside, near and inside a dark ring induced by a voltage applied to another probe and found the resistivity to be directly related to the observed absorbance of the film. The standard electrochromic mechanism of ion insertion was used to explain the observations. We anticipate this experimental...

  3. An optical sensor based on H-acid/layered double hydroxide composite film for the selective detection of mercury ion.

    Science.gov (United States)

    Sun, Zhiyong; Jin, Lan; Zhang, Shitong; Shi, Wenying; Pu, Min; Wei, Min; Evans, David G; Duan, Xue

    2011-09-19

    A novel optical chemosensor was fabricated based on 1-amino-8-naphthol-3,6-disulfonic acid sodium (H-acid) intercalated layered double hydroxide (LDH) film via the electrophoretic deposition (EPD) method. The film of H-acid/LDH with the thickness of 1 μm possesses a well c-orientation of the LDH microcrystals confirmed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The fluorescence detection for Hg(II) in aqueous solution was performed by using the H-acid/LDH film sensor at pH 7.0, with a linear response range in 1.0 × 10(-7) to 1.0 × 10(-5) mol L(-1) and a detection limit of 6.3 × 10(-8) mol L(-1). Furthermore, it exhibits excellent selectivity for Hg(II) over a large number of competitive cations including alkali, alkaline earth, heavy metal and transitional metals. The specific fluorescence response of the optical sensor is attributed to the coordination between Hg(II) and sulfonic group in the H-acid immobilized in the LDH matrix, which was verified by NMR spectroscopy and UV-vis spectra. In addition, density functional theory (DFT) calculation further confirms that the coordination occurs between one Hg(2+) and two O atoms in the sulfonic group, which is responsible for the significant fluorescence quenching of the H-acid/LDH film. The results indicate that the H-acid/LDH composite film can be potentially used as a chemosensor for the detection of Hg(2+) in the environmental and biomedical field.

  4. Temporal distribution of electron and ion emission caused by laser excitation of optical surfaces in ultra-high vacuum

    Science.gov (United States)

    Siekhaus, W. J.; Chase, L. L.; Milam, D.

    1986-05-01

    We have measured electron and ion emission under high vacuum conditions from several semiconductor and insulator surfaces excited by the first and third harmonics of a 1.06 micron Nd laser. The dependence of this emission on laser fluence and wavelength is consistent with a multiphoton excitation process. The dependence on laser pulse length implies, however, that other processes, either diffusive, thermal or thermomechanical, are also involved. Additional information is provided by the temporal and spatial distribution of the charge emission. The most extensive results have been obtained with single crystals of ZnS, for which nearly equal magnitudes of negative and positive charge emission are observed. The results suggest the possibility that the observed charge emission results primarily from the ejection of neutral atoms and molecules from the surface, followed by selective multiphoton ionization of one or more of the neutral species. The irreversible surface modification implied by the observed emission may be the precursor to observable surface damage. Detailed studies of the properties of the emitted particles may be very useful in developing a basic understanding of the damage mechanisms.

  5. Integration of biological ion channels onto optically addressable micro-fluidic electrode arrays for single molecule characterization.

    Energy Technology Data Exchange (ETDEWEB)

    Brozik, Susan Marie; Frink, Laura J. Douglas; Bachand, George David; Keller, David J. (University of New Mexico, Albuquerque, NM); Patrick, Elizabeth L.; Marshall, Jason A. (University of New Mexico, Albuquerque, NM); Ortiz, Theodore P. (University of New Mexico, Albuquerque, NM); Meyer, Lauren A. (University of New Mexico, Albuquerque, NM); Davis, Ryan W. (University of New Mexico, Albuquerque, NM); Brozik, James A. (University of New Mexico, Albuquerque, NM); Flemming, Jeb Hunter

    2004-12-01

    The challenge of modeling the organization and function of biological membranes on a solid support has received considerable attention in recent years, primarily driven by potential applications in biosensor design. Affinity-based biosensors show great promise for extremely sensitive detection of BW agents and toxins. Receptor molecules have been successfully incorporated into phospholipid bilayers supported on sensing platforms. However, a collective body of data detailing a mechanistic understanding of membrane processes involved in receptor-substrate interactions and the competition between localized perturbations and delocalized responses resulting in reorganization of transmembrane protein structure, has yet to be produced. This report describes a systematic procedure to develop detailed correlation between (recognition-induced) protein restructuring and function of a ligand gated ion channel by combining single molecule fluorescence spectroscopy and single channel current recordings. This document is divided into three sections: (1) reported are the thermodynamics and diffusion properties of gramicidin using single molecule fluorescence imaging and (2) preliminary work on the 5HT{sub 3} serotonin receptor. Thirdly, we describe the design and fabrication of a miniaturized platform using the concepts of these two technologies (spectroscopic and single channel electrochemical techniques) for single molecule analysis, with a longer term goal of using the physical and electronic changes caused by a specific molecular recognition event as a transduction pathway in affinity based biosensors for biotoxin detection.

  6. Structure and composition of zirconium carbide thin-film grown by ion beam sputtering for optical applications

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Amol, E-mail: modimh@rrcat.gov.in; Modi, Mohammed H., E-mail: modimh@rrcat.gov.in; Dhawan, Rajnish, E-mail: modimh@rrcat.gov.in; Lodha, G. S., E-mail: modimh@rrcat.gov.in [X-ray Optics Section, ISU Division, Raja Ramanna Centre for Advanced Technology, Indore-452013 (India)

    2014-04-24

    Thin film of compound material ZrC was deposited on Si (100) wafer using ion beam sputtering method. The deposition was carried out at room temperature and at base pressure of 3×10{sup −5} Pa. X-ray photoelectron spectroscopy (XPS) measurements were performed for determining the surface chemical compositions. Grazing incidence x-ray reflectivity (GIXRR) measurements were performed to study the film thickness, roughness and density. From GIXRR curve roughness value of the film was found less than 1 nm indicating smooth surface morphology. Films density was found 6.51 g/cm{sup 3}, which is close to bulk density. Atomic force microscopy (AFM) measurements were performed to check the surface morphology. AFM investigation showed that the film surface is smooth, which corroborate the GIXRR data. Figure 2 of the original article PDF file, as supplied to AIP Publishing, contained a PDF processing error. This article was updated on 12 May 2014 to correct that error.

  7. A comparison of the structural changes and optical properties of LiNbO3, Al2O3 and ZnO after Er+ ion implantation

    Science.gov (United States)

    Mackova, A.; Malinsky, P.; Pupikova, H.; Nekvindova, P.; Cajzl, J.; Svecova, B.; Oswald, J.; Wilhelm, R. A.; Kolitsch, A.

    2014-07-01

    This paper reports on the structural as well as compositional changes of LiNbO3, Al2O3 and ZnO crystals, implanted with Er+ ions at 190 keV a with fluence of 1.0 × 1016 cm-2 into the crystallographic cuts. Post-implantation annealing at 1000 °C in oxygen atmosphere was also done. The chemical compositions and erbium concentration-depth profiles of implanted layers were studied by Rutherford Backscattering Spectrometry (RBS) and compared to SRIM simulations. The same value of the maximum erbium concentration (up to 2 at.%) was observed at a depth of about 40 nm for all crystals. The structural properties of the prepared layers were characterised by RBS/channelling. The relative numbers of disordered atoms in the prepared implanted layers were compared with each other and discussed for various crystals. It has been found that erbium is located in LiNbO3 and in Al2O3 preferably in interstitial positions, unlike ZnO, where the largest amount of erbium (about 83%) is placed in substitutional positions after the implantation. The erbium position in the host matrix was substantially influenced by the annealing procedure. In ZnO, after the annealing, the erbium amount in substitutional positions significantly decreased; in LiNbO3 and Al2O3 the increase of erbium in substitutional positions was observed simultaneously with the improvement of the quality of the reconstructed host matrix. Since we are interested in the relationship between structural changes and optical properties, the erbium luminescence properties were measured in the region of wavelength 1440-1650 nm for all crystals. After ion implantation LiNbO3 samples had zero luminescence intensity, while ZnO and Al2O3 samples had one significant luminescence band at 1537 and 1530 nm, respectively. The annealing improved the luminescent properties significantly in all investigated crystalline materials.

  8. Electrical and optical properties of hydrogenated amorphous silicon-germanium (a-Si1 - xGexH) films prepared by reactive ion beam sputtering

    Science.gov (United States)

    Bhan, Mohan Krishan; Malhotra, L. K.; Kashyap, Subhash C.

    1989-09-01

    Thin films of hydrogenated amorphous silicon-germanium (a-Si1-xGex: H) alloys have been prepared by reactive ion beam sputtering of a composite target of silicon and germanium. The dependence of the deposition rate, conductivity-temperature variation, optical absorption coefficient, refractive index, imaginary part of the dielectric constant, hydrogen content, and infrared (IR) absorption spectra on germanium content (x) are reported and analyzed. For a typical composition—a-Si28Ge72:H (x=0.72), the effect of beam voltage, H2:Ar flow ratio, and substrate temperature on the material properties have also been investigated. For the films prepared with increasing x, the expected behavior of a decrease in both hydrogen content and band gap and an increase in the electrical conductivity have been observed. The films prepared at x>0.80 are found to be more homogeneous than the films deposited at 0.0disorder introduced by the random mixing of Si and Ge atoms in the a-Si1-xGex: H network in the latter case. The a-Si28Ge72:H films exhibiting minimum conductivity (1.7×10-7 Ω-1 cm-1) have been obtained for an H2:Ar flow ratio of 10:1 and a beam voltage and substrate temperature of 1500 V and 300 °C, respectively. These films contain a hydrogen concentration of 10.2 at. % and show an optical band gap of 1.25 eV. The IR studies have shown that a-Si28Ge72:H films prepared both at low beam voltages and at low substrate temperatures show the unusual preferential attachment of hydrogen to Ge rather than to Si.

  9. Correlation between SnO{sub 2} nanocrystals and optical properties of Eu{sup 3+} ions in SiO{sub 2} matrix: Relation of crystallinity, composition, and photoluminescence

    Energy Technology Data Exchange (ETDEWEB)

    Thanh, Bui Quang [International Training Institute for Materials Science (ITIMS), Hanoi University of Science and Technology (HUST), No.1 Dai Co Viet, Hanoi (Viet Nam); Ha, Ngo Ngoc, E-mail: hann@itims.edu.vn [International Training Institute for Materials Science (ITIMS), Hanoi University of Science and Technology (HUST), No.1 Dai Co Viet, Hanoi (Viet Nam); Khiem, Tran Ngoc, E-mail: khiem@itims.edu.vn [International Training Institute for Materials Science (ITIMS), Hanoi University of Science and Technology (HUST), No.1 Dai Co Viet, Hanoi (Viet Nam); Chien, Nguyen Duc [International Training Institute for Materials Science (ITIMS), Hanoi University of Science and Technology (HUST), No.1 Dai Co Viet, Hanoi (Viet Nam); School of Engineering Physics (SEP), Hanoi University of Science and Technology (HUST), No.1 Dai Co Viet, Hanoi (Viet Nam)

    2015-07-15

    We report characteristics and optical properties of Eu{sup 3+}-doped SnO{sub 2} nanocrystals dispersed in SiO{sub 2} matrix. Samples are prepared by the sol–gel method. Crystallinity of SnO{sub 2} nanocrystals is examined by X-ray diffraction experiments. At annealing temperatures from 900 to 1200 °C, we observe the formation of single tetragonal rutile structure of SnO{sub 2} nanocrystals. Average sizes of SnO{sub 2} nanocrystals within 3–7 nm are estimated by Debye–Scherrer equation. Intense photoluminescent spectra of Eu{sup 3+} ions consist of a series of resolved emission bands within 570–645 nm, which are varied with different sample-preparation conditions. We show the efficient excitation process of Eu{sup 3+} ions through SnO{sub 2} nanocrystals in the materials. Microscopic structure of SnO{sub 2} nanoparticles and optical properties of Eu{sup 3+} ions are also presented and discussed. - Highlights: • Thin layers of Eu{sup 3+} doped SnO{sub 2} nanocrystals dispersed in SiO{sub 2} were prepared by sol-gel method and spin-coating process. • Formation of single-phase tetragonal rutile structure of SnO{sub 2} nanocrystals and highly efficient optical excitation of the Eu{sup 3+} dopants were exhibited. • Relations of the crystallinity and composition of SnO{sub 2} and optical properties of Eu{sup 3+} dopants were comprehensively investigated and presented. • Allocations of major optically-active Eu{sup 3+} ions in the materials were deduced from their emission bands.

  10. Core-shell nanoparticles optical sensors - Rational design of zinc ions fluorescent nanoprobes of improved analytical performance

    Science.gov (United States)

    Woźnica, Emilia; Gasik, Joanna; Kłucińska, Katarzyna; Kisiel, Anna; Maksymiuk, Krzysztof; Michalska, Agata

    2017-10-01

    In this work the effect of affinity of an analyte to a receptor on the response of nanostructural fluorimetric probes is discussed. Core-shell nanoparticles sensors are prepared that benefit from the properties of the phases involved leading to improved analytical performance. The optical transduction system chosen is independent of pH, thus the change of sample pH can be used to control the analyte - receptor affinity through the ;conditional; binding constant prevailing within the lipophilic phase. It is shown that by affecting the ;conditional; binding constant the performance of the sensor can be fine-tuned. As expected, increase in ;conditional; affinity of the ligand embedded in the lipophilic phase to the analyte results in higher sensitivity over narrow concentration range - bulk reaction and sigmoidal shape response of emission intensity vs. logarithm of concentration changes. To induce a linear dependence of emission intensity vs. logarithm of analyte concentration covering a broad concentration range, a spatial confinement of the reaction zone is proposed, and application of core-shell nanostructures. The core material, polypyrrole nanospheres, is effectively not permeable for the analyte - ligand complex, thus the reaction is limited to the outer shell layer of the polymer prepared from poly(maleic anhydride-alt-1-octadecene). For herein introduced system a linear dependence of emission intensity vs. logarithm of Zn2+ concentration was obtained within the range from 10-7 to 10-1 M.

  11. The low-lying electronic states and optical schemes for the laser cooling of the BH(+) and BH(-) ions.

    Science.gov (United States)

    Zhang, Qing-Qing; Yang, Chuan-Lu; Wang, Mei-Shan; Ma, Xiao-Guang; Liu, Wen-Wang

    2017-07-05

    The potential energy curves and transition dipole moments for the 1(2)Σ(+), 2(2)Σ(+), 1(2)Π and 2(2)Π electronic states of the two molecules are calculated using multi-reference configuration interaction and the large basis sets aug-cc-pwCV5Z. Based on the obtained potential energy curves, the rotational and vibrational energy levels of the states are obtained by solving the Schrödinger equation of nuclear motion, and the spectroscopic parameters are then obtained by fitting the energy levels to Dunham series expansions. The spin-orbit coupling effect of the (2)Π states for both the BH(+) cation and BH(-) anion are calculated. Highly diagonally distributed Franck-Condon factors are determined for the 1(2)Σ(+) (v″=0)↔1(2)Π (v'=0) transition, ƒ00 (BH(+))=0.943, while the Franck-Condon factors for the 1(2)Π (v″=0)↔1(2)Σ(+) (v'=0) transition is ƒ00 (BH(-))=0.942. Moreover, the radiative lifetime of 38.2ns for the excited 1(2)Π state of the BH(+) and 91.8ns for the 1(2)Σ(+) state of the BH(-) are obtained, which are short enough for rapid laser cooling. A three-step optical scheme of the laser cooling is constructed for either the BH(+) cation or the BH(-) anion. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. The low-lying electronic states and optical schemes for the laser cooling of the BH+ and BH- ions

    Science.gov (United States)

    Zhang, Qing-Qing; Yang, Chuan-Lu; Wang, Mei-Shan; Ma, Xiao-Guang; Liu, Wen-Wang

    2017-07-01

    The potential energy curves and transition dipole moments for the 12Σ+, 22Σ+, 12Π and 22Π electronic states of the two molecules are calculated using multi-reference configuration interaction and the large basis sets aug-cc-pwCV5Z. Based on the obtained potential energy curves, the rotational and vibrational energy levels of the states are obtained by solving the Schrödinger equation of nuclear motion, and the spectroscopic parameters are then obtained by fitting the energy levels to Dunham series expansions. The spin-orbit coupling effect of the 2Π states for both the BH+ cation and BH- anion are calculated. Highly diagonally distributed Franck-Condon factors are determined for the 12Σ+ (v″ = 0) ↔ 12Π (v‧ = 0) transition, ƒ00 (BH+) = 0.943, while the Franck-Condon factors for the 12Π (v″ = 0) ↔ 12Σ+ (v‧ = 0) transition is ƒ00 (BH-) = 0.942. Moreover, the radiative lifetime of 38.2 ns for the excited 12Π state of the BH+ and 91.8 ns for the 12Σ+ state of the BH- are obtained, which are short enough for rapid laser cooling. A three-step optical scheme of the laser cooling is constructed for either the BH+ cation or the BH- anion.

  13. Leaky mode suppression in planar optical waveguides written in Er:TeO{sub 2}–WO{sub 3} glass and CaF{sub 2} crystal via double energy implantation with MeV N{sup +} ions

    Energy Technology Data Exchange (ETDEWEB)

    Bányász, I., E-mail: banyasz@sunserv.kfki.hu [Department of Crystal Physics, Wigner Research Centre for Physics, Hungarian Academy of Sciences, P.O.B. 49, H-1525 Budapest (Hungary); Zolnai, Z.; Fried, M. [Research Institute for Technical Physics and Materials Science, Research Centre for Natural Sciences, Hungarian Academy of Sciences, P.O.B. 49, Budapest H-1525 (Hungary); Berneschi, S. [MDF-Lab, “Nello Carrara” Institute of Applied Physics, IFAC-CNR, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy); “Enrico Fermi” Center for Study and Research, Piazza del Viminale 2, 00184 Roma (Italy); Pelli, S.; Nunzi-Conti, G. [MDF-Lab, “Nello Carrara” Institute of Applied Physics, IFAC-CNR, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy)

    2014-05-01

    Ion implantation proved to be an universal technique for producing waveguides in most optical materials. Tellurite glasses are good hosts of rare-earth elements for the development of fibre and integrated optical amplifiers and lasers covering all the main telecommunication bands. Er{sup 3+}-doped tellurite glasses are good candidates for the fabrication of broadband amplifiers in wavelength division multiplexing around 1.55 μm, as they exhibit large stimulated cross sections and broad emission bandwidth. Calcium fluoride is an excellent optical material, due to its perfect optical characteristics from UV wavelengths up to near IR. It has become a promising laser host material (doped with rare earth elements). Ion implantation was also applied to optical waveguide fabrication in CaF{sub 2} and other halide crystals. In the present work first single-energy implantations at 3.5 MeV at various fluences were applied. Waveguide operation up to 1.5 μm was observed in Er:Te glass, and up to 980 nm in CaF{sub 2}. Then double-energy implantations at a fixed upper energy of 3.5 MeV and lower energies between 2.5 and 3.2 MeV were performed to suppress leaky modes by increasing barrier width.

  14. Effect of Cr{sup 3+} ions on optical properties in {beta}-Ga{sub 2}O{sub 3} semiconductor

    Energy Technology Data Exchange (ETDEWEB)

    Wakai, Hirofumi; Sinya, Yuuta; Yamanaka, Akio [Chitose Institute of Science and Technology, Bibi 758-65, Chitose, Hokkaido 066-8655 (Japan)

    2011-02-15

    Cr-doping effects on optical properties of {beta}-Ga{sub 2}O{sub 3} have been studied in single-crystalline samples, grown by floating-zone method. The photoluminescence, which is observed as an intense and broad peak in nominally pure {beta}-Ga{sub 2}O{sub 3}, is found be abruptly suppressed by Cr-doping. This suppression demonstrates that a small amount of Cr{sup 3+} ions acts as non-radiative centers for photo-excited carriers. In Cr-doped {beta}-Ga{sub 2}O{sub 3} the residual photoluminescence shows UV and green emissions, peaking at about 3.3 eV and 2.4 eV, respectively. The photoluminescence excitation spectrum of the UV peak has a polarization-dependent maximum at the fundamental absorption edge that is arising from the band-to-band excitations. Therefore, the radiative decay channels for photo-excited carriers partly survive in Cr-doped {beta}-Ga{sub 2}O{sub 3}. We have also found a Cr-induced absorption band located just below the fundamental absorption edge (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  15. Effect of oxygen partial pressure on the structural and optical properties of ion beam sputtered TiO2 thin films

    Science.gov (United States)

    Tantray, Firdous A.; Chouhan, Romita; Rajput, Swati; Agrawal, Arpana; Andrews, Joseph T.; Sen, Pranay K.; Gupta, Mukul; Sen, Pratima

    2016-10-01

    We report the effect of oxygen partial pressure on the structural, electronic and nonlinear optical properties of ion beam sputtered TiO2 thin films deposited on glass substrate at 40% of oxygen (S1) and 20% of oxygen (S2) partial pressure. XRD data shows the crystalline nature of S1 film while the film S2 was amorphous in nature. The energy band gap of the thin films calculated from their UV-Vis spectra was found to be 3.63 eV (S1) and 3.56 eV (S2). The decrease in the band gap with decrease in oxygen partial pressure may be attributed to the amorphous nature of the film. The nonlinear refractive indices for both the films were obtained from the closed aperture Z-scan experiment performed using a cw He-Ne laser source operating at 632.8 nm and were found to be 17.6×10-9 m2/W and -5.64×10-9 m2/W for S1and S2 films, respectively. The reversal in the sign of the nonlinear refractive index may also be ascribed to the crystallinity of the grown films.

  16. Optical and electrical characterizations of a single step ion beam milling mesa devices of chloride passivated PbS colloidal quantum dots based film

    Science.gov (United States)

    Hechster, Elad; Shapiro, Arthur; Lifshitz, Efrat; Sarusi, Gabby

    2016-07-01

    Colloidal Quantum Dots (CQDs) are of increasing interest, thanks to their quantum size effect that gives rise to their usage in various applications, such as biological tagging, solar cells and as the sensitizing layer of night vision devices. Here, we analyze the optical absorbance of chloride passivated PbS CQDs as well as revealing a correlation between their photoluminescence and sizes distribution, using theoretical models and experimental results from the literature. Next, we calculate the CQDs resistivity as a film. Although resistivity can be calculated from sheet resistance measurement using four point probes, such measurement is usually carried-out on the layer's surface that in most cases has dangling bonds and surface states, which might affect the charges flow and modify the resistivity. Therefore; our approach, which was applied in this work, is to extract the actual resistivity from measurements that are performed along the film's thickness (z-direction). For this intent, we fabricated gold capped PbS mesas devices using a single step Ion Beam Milling (IBM) process where we milled the gold and the PbS film continually, and then measured the vertical resistance. Knowing the mesas' dimensions, we calculate the resistivity. To the best of our knowledge, no previous work has extracted, vertically, the resistivity of chloride passivated PbS CQDs using the above method.

  17. A novel orange emitting Sm3+ ions doped NaCaAlPO4F3 phosphor: Optical and luminescence properties

    Science.gov (United States)

    Nagaraja, R.; Pushpa Manjari, V.; Sailaja, B.; Ravikumar, R. V. S. S. N.

    2017-02-01

    A novel orange light emitting Sm3+ ions doped NaCaAlPO4F3 phosphor was synthesized via solid state reaction. The prepared sample was characterized by powder X-ray diffraction (PXRD), Optical absorption, Photoluminescence (PL) and Fourier Transform Infrared Spectroscopy (FT-IR) techniques. From powder XRD data, the average crystallite size and structural parameters are estimated. Absorption spectra consist of ten absorption peaks corresponding to the transitions from the 6H5/2 ground state to various excited energy levels. Transition probabilities, branching ratios and radiative lifetime were evaluated by using Judd-Ofelt analysis. Photoluminescence spectrum show three prominent emission bands centered at 562, 597 and 643 nm corresponding to the 4G5/2 → 6HJ (J = 5/2, 7/2 and 9/2) transitions respectively. From the emission transitions, stimulated emission cross-section (σe) and gain bandwidth (GBW) were predicted. The decay profiles of the prepared phosphor reveals the single exponential nature and the experimental lifetime is calculated. The colorimetric parameters CIE coordinates, Correlated color temperature of the prepared phosphor are also evaluated. FT-IR spectrum demonstrates the characteristic vibration bands of the prepared phosphor material.

  18. Optical and electrical characterizations of a single step ion beam milling mesa devices of chloride passivated PbS colloidal quantum dots based film

    Energy Technology Data Exchange (ETDEWEB)

    Hechster, Elad, E-mail: elad.hechster@gmail.com; Sarusi, Gabby [Electro-Optics Engineering Unit and Ilse Katz Institute for Nanoscale Science and Technology, Ben-Gurion University of the Negev, Beer-Sheva, 84100 Israel (Israel); Shapiro, Arthur; Lifshitz, Efrat [Schulich Faculty of Chemistry, Solid State Institute, Russel Berrie Nanotechnology Institute, Technion – Israel Institute of technology, 32000 Haifa (Israel)

    2016-07-15

    Colloidal Quantum Dots (CQDs) are of increasing interest, thanks to their quantum size effect that gives rise to their usage in various applications, such as biological tagging, solar cells and as the sensitizing layer of night vision devices. Here, we analyze the optical absorbance of chloride passivated PbS CQDs as well as revealing a correlation between their photoluminescence and sizes distribution, using theoretical models and experimental results from the literature. Next, we calculate the CQDs resistivity as a film. Although resistivity can be calculated from sheet resistance measurement using four point probes, such measurement is usually carried-out on the layer’s surface that in most cases has dangling bonds and surface states, which might affect the charges flow and modify the resistivity. Therefore; our approach, which was applied in this work, is to extract the actual resistivity from measurements that are performed along the film’s thickness (z-direction). For this intent, we fabricated gold capped PbS mesas devices using a single step Ion Beam Milling (IBM) process where we milled the gold and the PbS film continually, and then measured the vertical resistance. Knowing the mesas’ dimensions, we calculate the resistivity. To the best of our knowledge, no previous work has extracted, vertically, the resistivity of chloride passivated PbS CQDs using the above method.

  19. Optical pressure and temperature sensor based on the luminescence properties of Nd3+ ion in a gadolinium scandium gallium garnet crystal.

    Science.gov (United States)

    León-Luis, S F; Muñoz-Santiuste, J E; Lavín, V; Rodríguez-Mendoza, U R

    2012-04-23

    Hypersensitivity to pressure and temperature is observed in the near-infrared emission lines of the Nd(3+) ion in a Cr(3+),Nd(3+):Gd(3)Sc(2)Ga(3)O(12) crystal, associated to the R(1,2)((4)F(3/2))→Z(5)((4)I(9/2)) and R(1,2)((4)F(3/2))→Z(1)((4)I(9/2)) transitions. The former emissions show large linear pressure coefficients of -11.3 cm(-1)/GPa and -8.8 cm(-1)/GPa, while the latter show high thermal sensitivity in the low temperature range. Thus this garnet crystal can be considered a potential optical pressure and/or temperature sensor in high pressure and temperature experiments up to 12 GPa and below room temperature, used in diamond anvil cells and excited with different UV and visible commercial laser due to the multiple Cr(3+) and Nd(3+) absorption bands.

  20. Single- and double energy N{sup +} ion irradiated planar optical waveguides in Er: Tungsten–tellurite oxide glass and sillenite type Bismuth Germanate crystals working up to telecommunications wavelengths

    Energy Technology Data Exchange (ETDEWEB)

    Bányász, I., E-mail: banyasz@sunserv.kfki.hu [Department of Crystal Physics, Wigner Research Centre for Physics, Hungarian Academy of Sciences, P.O. Box 49, H-1525 Budapest (Hungary); Zolnai, Z.; Fried, M.; Lohner, T. [Research Institute for Technical Physics and Materials Science, Research Centre for Natural Sciences, Hungarian Academy of Sciences, P.O. Box 49, H-1525 Budapest (Hungary); Berneschi, S.; Righini, G.C. [MDF-Lab, “Nello Carrara” Institute of Applied Physics, IFAC-CNR, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy); “Enrico Fermi” Center for Study and Research, Piazza del Viminale 2, 00184 Roma (Italy); Pelli, S.; Nunzi-Conti, G. [MDF-Lab, “Nello Carrara” Institute of Applied Physics, IFAC-CNR, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy)

    2013-07-15

    Ion implantation proved to be a universal technique for producing waveguides in most optical materials. Tellurite glasses are good hosts of rare-earth elements for the development of fibre and integrated optical amplifiers and lasers covering all the main telecommunication bands. Er{sup 3+}-doped tellurite glasses are good candidates for the fabrication of broadband amplifiers in wavelength division multiplexing around 1.55 μm, as they exhibit large stimulated cross sections and broad emission bandwidth. Fabrication of channel waveguides in such a material via N{sup +} ion implantation was reported recently. Sillenite type Bismuth Germanate (BGO) crystals are good nonlinear optical materials. Parameters of waveguide fabrication in both materials via implantation of MeV-energy N{sup +} ions were optimized. First single-energy implantations at 3.5 MeV at various fluences were applied. Waveguide operation up to 1.5 μm was observed in both materials. Then double-energy implantations at a fixed upper energy of 3.5 MeV and lower energies between 2.5 and 3.1 MeV were performed to suppress leaky modes by increasing barrier width. Improvement of waveguide characteristics was found by m-line spectroscopy and spectroscopic ellipsometry.

  1. Cold Strontium Ion Source for Ion Interferometry

    Science.gov (United States)

    Jackson, Jarom; Durfee, Dallin

    2015-05-01

    We are working on a cold source of Sr Ions to be used in an ion interferometer. The beam will be generated from a magneto-optical trap (MOT) of Sr atoms by optically ionizing atoms leaking out a carefully prepared hole in the MOT. A single laser cooling on the resonant transition (461 nm) in Sr should be sufficient for trapping, as we've calculated that losses to the atom beam will outweigh losses to dark states. Another laser (405 nm), together with light from the trapping laser, will drive a two photon transition in the atom beam to an autoionizing state. Supported by NSF Award No. 1205736.

  2. Tuning of optical and electrical properties of wide band gap Fe:SnO2/Li:NiO p- n junctions using 80 MeV oxygen ion beam

    Science.gov (United States)

    Mistry, Bhaumik V.; Avasthi, D. K.; Joshi, U. S.

    2016-12-01

    Electrical and optical properties of pristine and swift heavy ion (SHI) irradiated p- n junction diode have been investigated for advanced electronics application. Fe:SnO2/Li:NiO p- n junction was fabricated by using pulsed laser deposition on c-sapphire substrate. The optical band gaps of Fe:SnO2 and Li:NiO films were obtained to be 3.88 and 3.37 eV, respectively. The current-voltage characteristics of the oxide-based p- n junction showed a rectifying behaviour with turn-on voltage of 0.95 V. The oxide-based p- n junction diode was irradiated to 80 MeV O+6 ions with 1 × 1012 ions/cm2 fluence. Decrease in grain size due to SHI irradiation is confirmed by the grazing angle X-ray diffraction and atomic force microscopy. In comparison with the pristine p- n junction diode, O+6 ion irradiated p-n junction diode shows the increase of surface roughness and decrease of percentage transmittance in visible region. For irradiated p- n junction diode, current-voltage curve has still rectifying behaviour but exhibits lower turn-on voltage than that of virgin p- n junction diode.

  3. Synthesis, structural and optical properties of pure and rare-earth ion doped TiO{sub 2} nanowire arrays by a facile hydrothermal technique

    Energy Technology Data Exchange (ETDEWEB)

    Bandi, Vengala Rao; Raghavan, Chinnambedu Murugesan; Grandhe, Bhaskar kumar; Kim, Sang Su [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Jang, Kiwan, E-mail: kwjang@changwon.ac.kr [Department of Physics, Changwon National University, Changwon 641-773 (Korea, Republic of); Shin, Dong-Soo [Department of Chemistry, Changwon National University, Changwon 641-773 (Korea, Republic of); Yi, Soung-Soo [Department of Photonics, Silla University, Busan 617-736 (Korea, Republic of); Jeong, Jung-Hyun [Department of Physics, Pukyong National University, Busan 608-737 (Korea, Republic of)

    2013-11-29

    Single crystalline pure and rare-earth metal ions (Eu{sup 3+} and Ce{sup 3+}) doped TiO{sub 2} nanowire arrays were prepared on conductive fluorine doped indium tin oxide substrates by a facile hydrothermal method. Initially the conditions and parameters were optimized to prepare the high quality TiO{sub 2} nanowire arrays in the absence of organic additives. The average diameter and length of the TiO{sub 2} nanowire were found to be ∼ 30–50 nm and ∼ 0.5–1.5 μm, respectively. The formations of rutile phase structure in all the samples were confirmed by x-ray diffractometric analysis while the transmission electron microscopy confirms the single crystallinity and the maximum orientation of growth direction along [001] for the as-grown TiO{sub 2} nanowire. The optical properties of all the samples were analyzed using photoluminescence spectroscopy. The photocatalytic properties of the pure and doped TiO{sub 2} were investigated for the decomposition of organic toludine blue-O dye under ultraviolet irradiation. The result demonstrates that the Ce{sup 3+}: TiO{sub 2} decomposed almost 90% of the organic dye within 80 min. - Highlights: • Rare-earth (RE) doped TiO{sub 2} nanowire arrays were prepared by hydrothermal method • RE doping enhanced the growth rate of TiO{sub 2} nanowire arrays • The catalysts used to check their photocatalytic activity by toludine blue-O dye • RE doped TiO2 act as unprecedented photocatalyst for organic dye decomposition.

  4. F center-molecular ion couples in alkali halides: Magneto-optics study (part two). Spin lattice relaxation time and electron spin memory; Studi di magnetoottica sulla coppia centro F-ione molecolare negli alogenuri alcalini: Parte 2. Misura del tempo di rilassamento spin-reticolo e della memoria di spin dell`elettrone nel ciclo ottico

    Energy Technology Data Exchange (ETDEWEB)

    Baldacchini, G.; Botti, S.; Grassano, U.M.; Luty, F.

    1991-10-01

    The spin-lattice relaxation time in the ground state, T/sub 1/, and the spin-mixing parameter during the optical cycle, epsilon, were measured in FH(OH) and FH(CN) centers in various alkali halides (KCl, KBr, KI, CsCl, and CsBr). For a close comparison, all experiments were performed before and after the optical association of the F center and molecular ion. T/sub 1/ becomes shorter before and still more after aggregation with respect to the values measured in the pure crystal, especially at very low magnetic fields. Epsilon decreases a little in crystals doped with OH-, while it increases a lot in crystals doped with CN-. Part of these results can be interpreted within the actual knowledge of the F-center physics. Part have been used to shed some light on the various unknown aspects of the energy transfer between the excited F-center and the molecular ion.

  5. Optical waveguides in laser crystals

    NARCIS (Netherlands)

    Pollnau, Markus; Romanyuk, Yaroslav E.

    2007-01-01

    This article reviews the recent research on different types of planar and channel crystalline optical waveguides, fabrication methods such as liquid phase epitaxy, pulsed laser deposition, thermal bonding, reactive ion or ion beam etching, wet chemical etching, ion in-diffusion, proton exchange, ion

  6. Nanobeam production with the multicusp ion source

    Science.gov (United States)

    Lee, Y.; Ji, Q.; Leung, K. N.; Zahir, N.

    2000-02-01

    A 1.8-cm-diam multicusp ion source to be used for focused ion beam applications has been tested for Xe, He, Ne, Ar, and Kr ions. The extractable ion and electron currents were measured. The extractable ion current is similar for all these ion species except for Ne+, but the extractable electron current behaves quite differently. The multicusp ion source will be used with a combined extractor-collimator electrode system that can provide a few hundred nA of Xe+ or Kr+ ions. Ion optics computation indicates that these beams can be further focused with an electrostatic column to a beam spot size of ˜100 nm.

  7. Methods for globally treating silica optics to reduce optical damage

    Science.gov (United States)

    Miller, Philip Edward; Suratwala, Tayyab Ishaq; Bude, Jeffrey Devin; Shen, Nan; Steele, William Augustus; Laurence, Ted Alfred; Feit, Michael Dennis; Wong, Lana Louie

    2012-11-20

    A method for preventing damage caused by high intensity light sources to optical components includes annealing the optical component for a predetermined period. Another method includes etching the optical component in an etchant including fluoride and bi-fluoride ions. The method also includes ultrasonically agitating the etching solution during the process followed by rinsing of the optical component in a rinse bath.

  8. Study of beam optics and beam halo by integrated modeling of negative ion beams from plasma meniscus formation to beam acceleration

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, K. [Naruto University of Education, 748 Nakashima, Takashima, Naruto-cho, Naruto-shi, Tokushima 772-8502 (Japan); Okuda, S.; Hatayama, A. [Faculty of Science and Technology, Keio University, 3-14-1 Hiyoshi, Kohoku-ku, Yokohama 223-8522 (Japan); Hanada, M.; Kojima, A. [Japan Atomic Energy Agency, 801-1 Mukouyama, Naka 319-0913 (Japan)

    2013-01-14

    To understand the physical mechanism of the beam halo formation in negative ion beams, a two-dimensional particle-in-cell code for simulating the trajectories of negative ions created via surface production has been developed. The simulation code reproduces a beam halo observed in an actual negative ion beam. The negative ions extracted from the periphery of the plasma meniscus (an electro-static lens in a source plasma) are over-focused in the extractor due to large curvature of the meniscus.

  9. FinalReport for completed IPP-0110 and 0110A Projects:"High Energy Ion Technology of Interfacial Thin Film Coatings for Electronic, Optical and Industrial Applications"

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Ian

    2009-09-01

    The DOE-supported IPP (Initiatives for Proliferation Prevention) Project, IPP-0110, and its accompanying 'add-on project' IPP-0110A, entitled 'High Energy Ion Technology of Interfacial Thin Film Coatings for Electronic, Optical and Industrial Applications' was a collaborative project involving the Lawrence Berkeley National Laboratory (LBNL) as the U.S. DOE lab; the US surface modification company, Phygen, Inc., as the US private company involved; and the High Current Electronics Institute (HCEI) of the Russian Academy of Sciences, Tomsk, Siberia, Russia, as the NIS Institute involved. Regular scientific research progress meetings were held to which personnel came from all participating partners. The meetings were held mostly at the Phygen facilities in Minneapolis, Minnesota (with Phygen as host) with meetings also held at Tomsk, Russia (HCEI as host), and at Berkeley, California (LBNL as host) In this way, good exposure of all researchers to the various different laboratories involved was attained. This report contains the Final Reports (final deliverables) from the Russian Institute, HCEI. The first part is that for IPP-0110A (the 'main part' of the overall project) and the second part is that for the add-on project IPP-0110A. These reports are detailed, and contain all aspects of all the research carried out. The project was successful in that all deliverables as specified in the proposals were successfully developed, tested, and delivered to Phygen. All of the plasma hardware was designed, made and tested at HCEI, and the performance was excellent. Some of the machine and performance parameters were certainly of 'world class'. The goals and requirements of the IPP Project were well satisfied. I would like to express my gratitude to the DOE IPP program for support of this project throughout its entire duration, and for the unparalleled opportunity thereby provided for all of the diverse participants in the project to join

  10. A spectroscopic ellispometric study of the tunability of the optical constants and thickness of GeO{sub x} films with swift heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Vijayarangamuthu, K.; Singh, Chaman; Rath, Shyama [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India); Kabiraj, D. [Inter-University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India)

    2011-09-15

    Sub-stoichiometric GeO{sub x} films were fabricated by electron-beam evaporation method. The films were irradiated with 100 MeV Ag{sup 7+} ions at fluences between 1 x 10{sup 12} and 1 x 10{sup 14} ions-cm{sup -2}. Spectroscopic ellipsometric measurements were performed in air at room temperature. The values of the layer thickness and refractive index were extracted from ellipsometry using a multilayer analysis and the Tauc Lorentz model. The refractive index (at 633 nm) of the as-deposited GeO{sub x} film was estimated to be 1.860 and decreased to 1.823 for films irradiated at an ion fluence of 1 x 10{sup 14} ions-cm{sup -2}. The thickness of the films also decreased after irradiation and is due to a sputtering induced by the ion beam. The change in the refractive index with ion fluence is attributed to a stoichiometric change and structural transformation represented by GeO{sub x}{yields} Ge + GeO{sub y} (y > x) occurring due to a thermal spike induced by ion irradiation. Swift heavy ions thus provide a scope for modulating the refractive index of GeO{sub x} films. The thickness and stoichiometric changes are supported by Rutherford backscattering measurements.

  11. Selective and sensitive speciation analysis of Cr(VI) and Cr(III) in water samples by fiber optic-linear array detection spectrophotometry after ion pair based-surfactant assisted dispersive liquid-liquid microextraction.

    Science.gov (United States)

    Yousefi, Seyedeh Mahboobeh; Shemirani, Farzaneh

    2013-06-15

    A simple ion pair based-surfactant assisted dispersive liquid-liquid microextraction (IP-SA-DLLME) was evaluated for extraction and preconcentration of Cr(VI) and Cr(III) in aqueous samples. In this method, which was used for the first time for chromium speciation analysis, sodium dodecyl sulfate (SDS) was used as both ion-pairing and disperser agent. Cr(VI) ions were converted into their cationic complex with 1,5-diphenylcarbazide (DPC) and then extracted into 1-octanol dispersed in aqueous solution. Cr(III) ion also can be determined by this procedure after oxidation to Cr(VI). After extraction and phase separation, upper organic phase was transferred to a micro cell of a fiber optic-linear array detection spectrophotometry (FO-LADS). The effects of various parameters on the extraction recovery were investigated. Under the optimized conditions and preconcentration of 10 mL of sample, the enrichment factor of 159 and the detection limit of 0.05 μgL(-1) were obtained. Validation of the method was performed by spiking-recovery method and comparison of results with those obtained by ET-AAS method.

  12. Optical waveguide properties of Ca{sub 0.4}Ba{sub 0.6}Nb{sub 2}O{sub 6} crystal formed by oxygen ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Tie-Jun; Zhou, Yu-Fan; Yu, Xiao-Fei; Liu, Tao; Zhang, Lian; Song, Hong-Lian; Qiao, Mei; Wang, Xue-Lin, E-mail: xuelinwang@sdu.edu.cn

    2015-07-01

    We report the fabrication of a planar optical waveguide in a Ca{sub 0.4}Ba{sub 0.6}Nb{sub 2}O{sub 6} crystal by irradiation with 6.0 MeV oxygen ions. We measured the guiding mode by the prism-coupling method at 633 nm and 1539 nm. The near-field intensity distributions were measured by the end-face coupling setup at a wavelength of 633 nm. The reflectivity calculation method (RCM) was used for reconstructing refractive index profiles. SRIM was used to simulate the electronic and nuclear stopping power caused by oxygen ion irradiation, and the finite-difference beam propagation method (FD-BPM) was used to simulate the near-field intensity distributions. Micro-Raman spectra were measured at room temperature in air to study the differences between the substrate and waveguide region.

  13. Selective and sensitive optical chemosensor for detection of Ag(I) ions based on 2(4-hydroxy pent-3-en-2-ylideneamine) phenol in aqueous samples.

    Science.gov (United States)

    Mirzaei, Mohammad; Saeed, Jaber

    2011-11-01

    A selective and sensitive chemosensor, based on the 2(4-hydroxy pent-3-en-2-ylideneamine) phenol (HPYAP) as chromophore, has been developed for colorimetric and visual detection of Ag(I) ions. HPYAP shows a considerable chromogenic behavior toward Ag(I) ions by changing the color of the solution from pale-yellow to very chromatic-yellow, which can be easily detected with the naked-eye. The chemosensor exhibited selective absorbance enhancement to Ag(I) ions in water samples over other metal ions at 438 nm, with a linear range of 0.4-500 μM (r(2)=0.999) and a limit of detection 0.07 μM of Ag(I) ions with UV-vis spectrophotometer detection. The relative standard deviation (RSD) for 100 μM Ag(I) ions was 2.05% (n=7). The proposed method was applied for the determination Ag(I) ions in water and waste water samples.

  14. CONDENSED MATTER: ELECTRONIC STRUCTURE, ELECTRICAL, MAGNETIC, AND OPTICAL PROPERTIES: Enhanced Laser Cooling of Rare-Earth-Ion-Doped Glass Containing Nanometer-Sized Metallic Particles

    Science.gov (United States)

    Jia, You-Hua; Zhong, Biao; Yin, Jian-Ping

    2009-03-01

    The enhanced laser cooling performance of rare-earth-ions-doped glasses containing small particles is predicted. This is achieved by the enhancement of local field around rare earth ions, owing to the surface plasmon resonance of small metallic particles. The role of energy transfer between ions and the particle is theoretical discussed. Depending on the particle size and the ion emission quantum efficiency, the enhancement of the absorption and the fluorescence is predicted. Moreover, taking Yb3+ -doped ZBLAN as example, the cooling power and heat-light converting efficiency are calculated. It is finally concluded that the absorption and the fluorescence are greatly enhanced in these composite materials, the cooling power is increased compared to the bulk material.

  15. Optics/Optical Diagnostics Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The Optics/Optical Diagnostics Laboratory supports graduate instruction in optics, optical and laser diagnostics and electro-optics. The optics laboratory provides...

  16. Optical and FT Infrared Absorption Spectra of 3d Transition Metal Ions Doped in NaF-CaF2-B2O3 Glass and Effects of Gamma Irradiation

    Directory of Open Access Journals (Sweden)

    F. H. A. Elbatal

    2014-01-01

    Full Text Available Combined optical and FTIR spectroscopy has been employed to investigate the undoped NaF-CaF2-B2O3 glass together with samples containing 0.2% dopant of 3d TM ions before and after gamma irradiation. The optical spectrum of the undoped glass reveals strong UV absorption with two peaks which are related to unavoidable trace iron impurity within the raw materials. Upon gamma irradiation, an induced visible broad band centered at 500 nm is resolved and is related to B-O hole center or nonbridging oxygen hole center. TMs-doped samples exhibit characteristic absorption due to each respective TM ion but with faint colors. Gamma irradiation of TMs-doped samples reveals the same induced visible band at 500–510 nm in most samples except CuO and Cr2O3-doped glasses. Infrared absorption spectra reveal characteristic vibrational bands due to triangular and tetrahedral borate groups. The introduction of NaF and CaF2 modifies the borate network forming BO3F tetrahedra. The introduction of 3d TMs as dopants did not make any obvious changes in the FTIR spectra due to their low content (0.2%. Gamma irradiation causes only minor variations in the intensities of the characteristic IR borate bands while the bands at about 1640 cm−1 and 3450 cm−1 reveal distinct growth in most samples.

  17. Optical system optimization of the microprobe beamline of the Ion Implantation Laboratory (IF-UFRGS), Brazil; Otimizacao do sistema optico da linha de microfeixe de ions do Laboratorio de Implantacao Ionica da UFRGS

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, Deiverti de Vila

    2015-07-01

    The aim of the present work is to optimize the microprobe beamline of the Ion Implantation Laboratory (IF-UFRGS). In short, an ion microprobe consists of charged particles focused to the dimensions of a few micrometers. The focusing system is made of two slits for demagnification, a set of magnetic lenses with scanning capability and a reaction chamber. By changing the parameters related to this system, one can optimize the features of the beam. To that end, samples of poly(tereftalate etylene) were irradiated with 2.2 MeV H+ ions and etched, yielding 2D microstructures with high aspect ratio. The analysis of the structures with Scanning Electron Microscopy proved to be an important tool in order to establish a correlation between the size of the microstructures and the parameters of the focusing system. In this work, the causes leading to a beam enlargement are discussed, as well as the aberrations which affect the system. Finally, the advantages of using ions for lithography purposes is pointed out. (author)

  18. Design study of primary ion provider for relativistic heavy ion collider electron beam ion source.

    Science.gov (United States)

    Kondo, K; Kanesue, T; Tamura, J; Okamura, M

    2010-02-01

    Brookhaven National Laboratory has developed the new preinjector system, electron beam ion source (EBIS) for relativistic heavy ion collider (RHIC) and National Aeronautics and Space Administration Space Radiation Laboratory. Design of primary ion provider is an essential problem since it is required to supply beams with different ion species to multiple users simultaneously. The laser ion source with a defocused laser can provide a low charge state and low emittance ion beam, and is a candidate for the primary ion source for RHIC-EBIS. We show a suitable design with appropriate drift length and solenoid, which helps to keep sufficient total charge number with longer pulse length. The whole design of primary ion source, as well as optics arrangement, solid targets configuration and heating about target, is presented.

  19. Optical and electronic properties of single modulation doped GaAs/AlGaAs V-grooved quantum wire modified by ion implantation

    Institute of Scientific and Technical Information of China (English)

    HUANG Shaohua; CHEN Zhanghai; BAI Lihui; WANG Fangzhen; SHEN Xuechu

    2005-01-01

    Single GaAs/Al0.5Ga0.5As V-grooved quantum wire modified by selective ion-implantation and rapid thermally annealing was investigated by spatially-resolved microphotoluminescence and magneto-resistance measurement. Spatially-resolved photoluminescence results indicate that the ion-implantation induced quantum well intermixing raises significantly the electron subband energies of the side quantum wells and vertical quantum wells, and more efficient accumulation of electrons in the quantum wires is achieved. Furthermore, the polarization properties of the photoluminescence from the quantum wires show large linear polarization degree up to 63%. Magneto-transport investigation on the ion implanted quantum wire samples presents the quasi-one dimensional intrinsic motion of electrons, which is important for the design and optimization of one dimensional electronic devices.

  20. Ion-Ion Neutralization.

    Science.gov (United States)

    1980-12-31

    plasma were identified using a downstream quadrupole mass spectrometer. In these experimento it is a simple matter to establish H+(H 2 0):f as the...pressure as predicted by the Thomson t2rnary mechanism whicK hzr been suownr to be valid experimentally at hiTh rrsurs (,han and Peron, 1:EI4 hereafter t...of NO , NO2 ions in various gases and the ternary recombination coefficients of these ions in the higher pres:;ure ( Thomson ) re"ie. Equation (5) cr>n