Tipping Time of a Quantum Rod

Science.gov (United States)

Parrikar, Onkar

2010-01-01

The behaviour of a quantum rod, pivoted at its lower end on an impenetrable floor and restricted to moving in the vertical plane under the gravitational potential, is studied analytically under the approximation that the rod is initially localized to a "small-enough" neighbourhood around the point of classical unstable equilibrium. It is shown…

Automatic operation device for control rods

International Nuclear Information System (INIS)

Sekimizu, Koichi

1984-01-01

Purpose: To enable automatic operation of control rods based on the reactor operation planning, and particularly, to decrease the operator's load upon start up and shutdown of the reactor. Constitution: Operation plannings, demand for the automatic operation, break point setting value, power and reactor core flow rate change, demand for operation interrupt, demand for restart, demand for forecasting and the like are inputted to an input device, and an overall judging device performs a long-term forecast as far as the break point by a long-term forecasting device based on the operation plannings. The automatic reactor operation or the like is carried out based on the long-term forecasting and the short time forecasting is performed by the change in the reactor core status due to the control rod operation sequence based on the control rod pattern and the operation planning. Then, it is judged if the operation for the intended control rod is possible or not based on the result of the short time forecasting. (Aizawa, K.)

Effect of Hurricane Andrew on the Turkey Point Nuclear Generating Station from August 20--30, 1992

International Nuclear Information System (INIS)

Hebdon, F.J.

1993-03-01

On August 24, 1992, Hurricane Andrew, a Category 4 hurricane, struck the Turkey Point Electrical Generating Station with sustained winds of 145 mph (233 km/h). This is the report of the team that the US Nuclear Regulatory Commission (NRC) and the Institute of Nuclear Power Operations (INPO) jointly sponsored (1) to review the damage that the hurricane caused the nuclear units and the utility's actions to prepare for the storm and recover from it, and (2) to compile lessons that might benefit other nuclear reactor facilities

Control rod position detection device

International Nuclear Information System (INIS)

Akita, Haruo; Ogiwara, Sakae.

1996-01-01

The device of the present invention is used in a back-up shut down system of an LMFBR type reactor which is easy for maintenance, has high reliability and can recognize the position of control rods accurately. Namely, a permanent magnet is disposed to a control rod extension tube connected to the lower portion of the control rod. The detector guide tube is disposed in the vicinity of the control rod extension tube. A detector having a detection coil is inserted into a detector tube. With such constitution, the control rod can be detected at one position using the following method. (1) the movement of the magnetic field of the permanent magnet is detected by the detection coil. (2) a plurality of grooves are formed on the control rod extension tube, and the movement of the grooves is detected. In addition, the detection coil is inserted into the detector guide tube, and the signals from the detection coil are inputted to a signal processing circuit disposed at the outside of the reactor vessel using an MI cable to enable the maintenance of the detector. Further, if the detector comprises a detection coil and an excitation coil, the position of a dropped control rod can be recognized at a plurality of points. (I.S.)

RETRAN applications in pressurized thermal shock analysis of turkey point units 3 and 4

International Nuclear Information System (INIS)

Arpa, J.; Fatemi, A.S.; Mathavan, S.K.

1985-01-01

A methodology to assess the impact of overcooling transients on vessel wall integrity with respect to pressurized thermal shock conditions has been developed at Florida Power and Light Company for the Turkey Point Nuclear Units. Small break loss-of-coolant and small steamline break events have been simulated with the RETRAN code. Highly conservative assumptions, such as engineered safeguards with minimum temperature and maximum flow, have been made to maximize cooldown and thermal stress in the vessel wall. Temperatures, pressures, and flows obtained with RETRAN provide input for stress and fracture mechanics analyses that evaluate reactor vessel integrity. The results of the RETRAN analyses compare well with generic calculations performed by the Westinghouse Owners Group for a similar type of plant

BRIGITTE, Dose Rate and Heat Source and Energy Flux for Self-Absorbing Rods

International Nuclear Information System (INIS)

Jegu, M.; Clement, M.

1978-01-01

1 - Nature of physical problem solved: Calculation of dose rate, heat sources or energy flux. The sources are self-absorbing radioactive rods. The shielding consists of blocks of which the cross section can be defined. 2 - Method of solution: Exponential attenuation and build-up factor between source points and detector points. Source integration with error estimate. Automatic or controlled build-up with monitor print-out. 3 - Restrictions on the complexity of the problem: Number of energy points, regions, detector points, abscissa points of the rod, vertical position of the rod, are all limited to ten. The maximum total number of vertical steps is 124

Control rod

International Nuclear Information System (INIS)

Kawakami, Kazuo; Shimoshige, Takanori; Nishimura, Akira

1979-01-01

Purpose: A control rod has been developed, which provided a plurality of through-holes in the vicinity of the sheath fitting position, in order to flatten burn-up, of fuel rods in positions confronting a control rod. Thereby to facilitate the manufacture of the control rods and prevent fuel rod failures. Constitution: A plurality of through-holes are formed in the vicinity of the sheath fitting position of a central support rod to which a sheath for the control rod is fitted. These through-holes are arranged in the axial direction of the central support rod. Accordingly, burn-up of fuel rods confronting the control rods can be reduced by through-holes and fuel rod failures can be prevented. (Yoshino, Y.)

Diversity of management strategies in Mesoamerican turkeys: archaeological, isotopic and genetic evidence

Science.gov (United States)

Manin, Aurelie; Corona-M, Eduardo; Craig, Abigail; Thornton, Erin Kennedy; Yang, Dongya Y.; Richards, Michael

2018-01-01

The turkey (Meleagris gallopavo) represents one of the few domestic animals of the New World. While current research points to distinct domestication centres in the Southwest USA and Mesoamerica, several questions regarding the number of progenitor populations, and the timing and intensity of turkey husbandry remain unanswered. This study applied ancient mitochondrial DNA and stable isotope (δ13C, δ15N) analysis to 55 archaeological turkey remains from Mexico to investigate pre-contact turkey exploitation in Mesoamerica. Three different (sub)species of turkeys were identified in the archaeological record (M. g. mexicana, M. g. gallopavo and M. ocellata), indicating the exploitation of diverse local populations, as well as the trade of captively reared birds into the Maya area. No evidence of shared maternal haplotypes was observed between Mesoamerica and the Southwest USA, in contrast with archaeological evidence for trade of other domestic products. Isotopic analysis indicates a range of feeding behaviours in ancient Mesoamerican turkeys, including wild foraging, human provisioning and mixed feeding ecologies. This variability in turkey diet decreases through time, with archaeological, genetic and isotopic evidence all pointing to the intensification of domestic turkey management and husbandry, culminating in the Postclassic period. PMID:29410864

Diversity of management strategies in Mesoamerican turkeys: archaeological, isotopic and genetic evidence.

Science.gov (United States)

Manin, Aurelie; Corona-M, Eduardo; Alexander, Michelle; Craig, Abigail; Thornton, Erin Kennedy; Yang, Dongya Y; Richards, Michael; Speller, Camilla F

2018-01-01

The turkey ( Meleagris gallopavo ) represents one of the few domestic animals of the New World. While current research points to distinct domestication centres in the Southwest USA and Mesoamerica, several questions regarding the number of progenitor populations, and the timing and intensity of turkey husbandry remain unanswered. This study applied ancient mitochondrial DNA and stable isotope ( δ 13 C, δ 15 N) analysis to 55 archaeological turkey remains from Mexico to investigate pre-contact turkey exploitation in Mesoamerica. Three different (sub)species of turkeys were identified in the archaeological record ( M. g. mexicana , M. g. gallopavo and M. ocellata ), indicating the exploitation of diverse local populations, as well as the trade of captively reared birds into the Maya area. No evidence of shared maternal haplotypes was observed between Mesoamerica and the Southwest USA, in contrast with archaeological evidence for trade of other domestic products. Isotopic analysis indicates a range of feeding behaviours in ancient Mesoamerican turkeys, including wild foraging, human provisioning and mixed feeding ecologies. This variability in turkey diet decreases through time, with archaeological, genetic and isotopic evidence all pointing to the intensification of domestic turkey management and husbandry, culminating in the Postclassic period.

Control rod drive mechanism

International Nuclear Information System (INIS)

Mizuno, Katsuyuki.

1976-01-01

Object: To restrict the reduction in performance due to stress corrosion cracks by making use of condensate produced in a turbine steam condenser. Structure: Water produced in a turbine steam condenser is forced into a condensed water desalting unit by low pressure condensate pump. The condensate is purified and then forced by a high pressure condensate pump into a feedwater heater for heating before it is returned to the reactor by a feedwater pump. Part of the condensate issuing from the condensate desalting unit is branched from the remaining portion at a point upstream the pump and is withdrawn into a control rod drive water pump after passing through a motordriven bypass valve, an orifice and a condenser water level control valve, is pressurized in the control rod drive water desalting unit and supplied to a control rod drive water pressure system. The control rod is vertically moved by the valve operation of the water pressure system. Since water of high oxygen concentration does not enter during normal operation, it is possible to prevent the stress cracking of the stainless steel apparatus. (Nakamura, S.)

Magnetic switch for reactor control rod

International Nuclear Information System (INIS)

Germer, J.H.

1986-01-01

This patent describes a control rod system for a nuclear reactor utilizing an electromagnetic grapple mechanism for holding and releasing a control rod, the improvement comprising a magnetic reed switch assembly having a Curie-point magnetic shunt and responsive to reactor coolant temperature for short circuiting the electromagnetic grapple mechanism causing release of the control rod when the coolant temperature reaches the Curie-point of the magnetic shunt. The magnetic reed switch assembly includes a: a permanent magnet, a pair of magnetic pole pieces located at and in contact with opposite ends of the permanent magnet, the Curie-point magnetic shunt being positioned adjacent the permanent magnet and in contact with the pair of magnetic pole pieces, and a reed switch positioned intermediate the pole pieces and provided with a pair of ferromagnetic reeds, a nonmagnetic enclosure around the reeds, a first of the reeds being secured at one end to a first of the pair of pole pieces, a second of the reeds having one end extending into and secured to a hollow member positioned in and extending through a second of the pair of pole pieces, the one end of the second of the reeds secured to a condector adapted to be connected to the electromagnetic grapple mechanism

Neonatal outcome following new assisted reproductive technology regulations in Turkey - a nationwide multicenter point prevalence study.

Science.gov (United States)

Kultursay, Nilgun; Yalaz, Mehmet; Koroglu, Ozge Altun

2015-01-01

In March 2010, a new legislation about assisted reproductive technology (ART) activities, favoring single embryo transfer, was introduced in Turkey. Consequences of new regulations on neonatal outcome have not been evaluated in multicenter studies yet. In this study, our aim was to evaluate neonatal outcome of infants from medically assisted reproduction (MAR) pregnancies in the post-legislation era. A point prevalence study was conducted at 51 centers in Turkey on 1 April 2013. Data about fertility treatments and neonatal characteristics were evaluated for "live births" (Group 1) and "patients being cared in the NICU" (Group 2). Seventeen (4%) of 420 infants in group 1, and 89 (8.1%) of 1094 infants in group 2 were born after MAR pregnancies. The ratio of multiple births in MAR pregnancies was still very high as 47.1% for group 1, 69.1% for group 2 infants. MAR babies constituted 9.9% of infants in Level 3 NICUs and 7.6% infants in Level 2 NICUs. MAR was associated with increased risk of multiple births and prematurity. After the new legislation, multiple birth rates are still high in MAR pregnancies, resulting in unfavorable neonatal outcomes. Efforts to decrease multiple birth rates should be encouraged.

Dynamic rod worth measurements (''Rod Insertion''). Final report for the period 01 December 1994 - 30 November 1996

International Nuclear Information System (INIS)

Bogdan, G.

1996-12-01

Reload startup physics tests are performed for pressurized water reactors (PWR power plant) following a refuelling or other significant core alteration for which nuclear design calculations are required. Part of the reload startup physics tests are control rod group worths measurements. for this purpose a new so-called method ''Rod-Insertion'' was developed. It can also be used as an additional measuring instrument on the research reactor for education purposes. The principle of the rod-insertion method is to start from a critical reactor operating at low power and to measure the time-dependent reactivity change while a control rod is inserted into the core. Unlike in the rod-drop method, the measured control rod is inserted with the drive mechanism at normal speed. By analyzing the flux trace using point-kinetics, not only the total rod worth but also the differential and the integral rod worth curves are obtained. A high-quality electrometer is required for monitoring the neutron flux. The analysis is performed by transferring the data to an IBM PC compatible with some additional standard electronic board and the associated software. The new reactivity meter has been validated on the TRIGA Mark II reactors in Ljubljana and Vienna and at the Krsko Nuclear Power Plant during physics startup tests after reload. The results proved the high performance of the reactivity meter in the standard applications according to the existing procedures, as well as in the new rod-insertion technique of measuring the control rod group worths. This method drastically differs from others such as absence of any chemical control of reactivity (like boron exchange method), and minimizing a testing time and waste coolant production

Description of osteomyelitis lesions associated with Actinomyces pyogenes infection in the proximal tibia of adult male turkeys.

Science.gov (United States)

Brinton, M K; Schellberg, L C; Johnson, J B; Frank, R K; Halvorson, D A; Newman, J A

1993-01-01

Actinomyces pyogenes was isolated from osteomyelitis lesions from the proximal tibia of mature tom turkeys. Gram-stained impression smears of the lesions resulted in bacteria that appeared as club-shaped, gram-positive pleomorphic rods. The bacteria grew better in a reduced-oxygen environment. The lesions were well demarcated and cavernous, ranging from purulent to caseous in consistency.

Effect of Hurricane Andrew on the Turkey Point Nuclear Generating Station from August 20--30, 1992. [Final report

Energy Technology Data Exchange (ETDEWEB)

Hebdon, F.J. [Institute of Nuclear Power Operations, Atlanta, GA (United States)

1993-03-01

On August 24, 1992, Hurricane Andrew, a Category 4 hurricane, struck the Turkey Point Electrical Generating Station with sustained winds of 145 mph (233 km/h). This is the report of the team that the US Nuclear Regulatory Commission (NRC) and the Institute of Nuclear Power Operations (INPO) jointly sponsored (1) to review the damage that the hurricane caused the nuclear units and the utility`s actions to prepare for the storm and recover from it, and (2) to compile lessons that might benefit other nuclear reactor facilities.

Characterization of Emericella nidulans RodA and DewA hydrophobin mutants

DEFF Research Database (Denmark)

Jensen, Britt Guillaume; Nielsen, Jakob Blæsbjerg; Pedersen, Mona Højgaard

hydrophobins RodA and DewA. Individual knock-out mutants rodAΔ, dewAΔ and the double deletion strain rodAΔdewAΔ were constructed. Furthermore, two strains containing a point mutation in the first of the cysteines of RodA (rodA-C57G), where one was coupled to the dewA deletion, were included. The reference...... strain (NID1) and dewAΔ displayed green conidia. However, rodAΔ and rodAΔdewAΔ showed a dark green/brown conidial pigmentation, while rodA-C57G and rodAC57G dewAΔ displayed lighter brown conidia. rodAΔ and rodAΔdewAΔ displayed a higher degree of hülle cells compared to the moderate amount observed...... for NID1 and dewAΔ, while rodA-C57G and rodA-C57G dewAΔ displayed a low number of hülle cells. NID1 and dewAΔ conidia were dispersed as spore chains. rodAΔ, rodAΔdewAΔ, rodA-C57G and rodA-C57G dewAΔ spores were associated in large clumps, where the conidia seemed to adhere to one another. The largest...

Use of the ''Lagrangian and Eulerian points of view'' in the transient critical heat flux calculations for BWR rod bundles and experimental verifications

International Nuclear Information System (INIS)

Marinelli, V.; Pellei, A.; Vallero, P.; Vitanza, C.

1975-01-01

The calculations performed in comparison of the ''Lagrangian point of view'', by means of the DOLCE computer code with the local space--time approach of the ''Eulerian point of view'' indicate that the two methods give substantially equivalent results and predict satisfactorily the onset of the transient CHF for the Centro Informazioni Studi Esperienze annuli experimental data and General Electric Company 16-rod bundles data under typical boiling water reactor transients, including loss-of-coolant accident simulations. 9 references

Control rod

International Nuclear Information System (INIS)

Igarashi, Takao; Sugawara, Satoshi; Yoshimoto, Yuichiro; Saito, Shozo; Fukumoto, Takashi.

1987-01-01

Purpose: To reduce the weight and thereby obtain satisfactory operationability of control rods by combining absorbing nuclear chain type neutron absorbers and conventional type neutron absorbers in the axial direction of blades. Constitution: Neutron absorber rods and long life type neutron absorber rods are disposed in a tie rod and a sheath. The neutron absorber rod comprises a poison tube made of stainless steels and packed with B 4 C powder. The long life type neutron absorber rod is prepared by packing B-10 enriched boron carbide powder into a hafnium metal rod, hafnium pipe, europium and stainless made poison tube. Since the long life type absorber rod uses HF as the absorbing nuclear chain type neutron absorber, it absorbs neutrons to form new neutron absorbers to increase the nuclear life. (Yoshino, Y.)

Control rods

International Nuclear Information System (INIS)

Maruyama, Hiromi.

1984-01-01

Purpose: To realize effective utilization, cost reduction and weight reduction in neutron absorbing materials. Constitution: Residual amount of neutron absorbing material is averaged between the top end region and other regions of a control rod upon reaching to the control rod working life, by using a single kind of neutron absorbing material and increasing the amount of the neutron absorber material at the top end region of the control rod as compared with that in the other regions. Further, in a case of a control rod having control rod blades such as in a cross-like control rod, the amount of the neutron absorbing material is decreased in the middle portion than in the both end portions of the control rod blade along the transversal direction of the rod, so that the residual amount of the neutron absorbing material is balanced between the central region and both end regions upon reaching the working life of the control rod. (Yoshihara, H.)

Accident-tolerant control rod

International Nuclear Information System (INIS)

Ohta, Hirokazu; Sawabe, Takashi; Ogata, Takanari

2013-01-01

Boron carbide (B 4 C) and hafnium (Hf) metal are used for the neutron absorber materials of control rods in BWRs, and silver-indium-cadmium (Ag-In-Cd) alloy is used in PWRs. These materials are clad with stainless steel. The eutectic point of B 4 C and iron (Fe) is about 1150 deg. C and the melting point of Ag-In-Cd alloy is about 800 deg. C, which are lower than the temperature of zircaloy - steam reaction increases rapidly (∼1200 deg. C). Accordingly, it is possible that the control rods melt and collapse before the reactor core is significantly damaged in the case of severe accidents. Since the neutron absorber would be separated from the fuels, there is a risk of re-criticality, when pure water or seawater is injected for emergency cooling. In order to ensure sub-criticality and extend options of emergency cooling in the course of severe accidents, a concept of accident-tolerant control rod (ACT) has been derived. ACT utilises a new absorber material having the following properties: - higher neutron absorption than current control rod; - higher melting or eutectic temperature than 1200 deg. C where rapid zircaloy oxidation occurs; - high miscibility with molten fuel materials. The candidate of a new absorber material for ATC includes gadolinia (Gd 2 O 3 ), samaria (Sm 2 O 3 ), europia (Eu 2 O 3 ), dysprosia (Dy 2 O 3 ), hafnia (HfO 2 ). The melting point of these materials and the liquefaction temperature with Fe are higher than the rapid zircaloy oxidation temperature. ACT will not collapse before the core melt-down. After the core melt-down, the absorber material will be mixed with molten fuel material. The current absorber materials, such as B 4 C, Hf and Ag-In-Cd, are charged at the tip of ATC in which the neutron flux is high, and a new absorber material is charged in the low-flux region. This design could minimise the degradation of a new absorber material by the neutron absorption and the influence of ATC deployment on reactor control procedure. As a

3-D rod ejection analysis using a conservative methodology

Energy Technology Data Exchange (ETDEWEB)

Park, Min Ho; Park, Jin Woo; Park, Guen Tae; Um, Kil Sup; Ryu, Seok Hee; Lee, Jae Il; Choi, Tong Soo [KEPCO, Daejeon (Korea, Republic of)

2016-05-15

The point kinetics model which simplifies the core phenomena and physical specifications is used for the conventional rod ejection accident analysis. The point kinetics model is convenient to assume conservative core parameters but this simplification loses large amount of safety margin. The CHASER system couples the three-dimensional core neutron kinetics code ASTRA, the sub-channel analysis code THALES and the fuel performance analysis code FROST. The validation study for the CHASER system is addressed using the NEACRP three-dimensional PWR core transient benchmark problem. A series of conservative rod ejection analyses for the APR1400 type plant is performed for both hot full power (HFP) and hot zero power (HZP) conditions to determine the most limiting cases. The conservative rod ejection analysis methodology is designed to properly consider important phenomena and physical parameters.

Determination and microscopic study of incipient defects in irradiated power reactor fuel rods. Final report

International Nuclear Information System (INIS)

Pasupathi, V.; Perrin, J.S.; Roberts, E.

1978-05-01

This report presents the results of nondestructive and destructive examinations carried out on the Point Beach-1 (PWR) and Dresden-3 (BWR) candidate fuel rods selected for the study of pellet-clad interaction (PCI) induced incipient defects. In addition, the report includes results of examination of sections from Oskarshamn-1 (BWR) fuel rods. Eddy current examination of Point Beach-1 rods showed indications of possible incipient defects in the fuel rods. The profilometry and the gamma scan data also indicated that the source of the eddy current indications may be incipient defects. No failed rods or rods with incipient failure were found in the sample from Point Beach-1. Despite the lack of success in finding incipient defects and filed rods, the mechanism for fuel rod failures in Point Beach-1 is postulated to be PCI-related, with high startup rates and fuel handling being the key elements. Nine out of the 10 candidate fuel rods from Dresden-3 (BWR) were failed, and all the failed rods had leaked water so that the initial mechanism was observed. Examination of clad inner surfaces of the specimens from failed and unfailed rods showed fuel deposits of widely varying appearance. The deposits were found to contain uranium, cesium, and tellurium. Transmission electron microscopy of clad specimens showed evidence of microscopic strain. Metallographic examination of fuel pellets from the peak transient power location showed extensive grain boundary separation and axial movement of the fuel indicative of rapid release of fission products. Examination of Oskarshamn clad specimens did not show any stress corrosion crack (SCC) type defects. The defects found in the examinations appear to be related to secondary hydriding. The clad inner surface of the Oskarshamn specimens also showed uranium-rich deposits of varying features

How Turkey Meets MPOWER Criteria?

Directory of Open Access Journals (Sweden)

Nazmi Bilir

2013-02-01

Full Text Available In 2003 World Health Assembly adopted an international treaty on tobacco control; FCTC, Framework Convention on Tobacco Control. Five year later World Health Organization (WHO declared the six effective approach for tobacco control, under the name of MPOWER. In the following years, WHO evaluated the level of implementation of MPOWER criteria in the countries. In this article, how Turkey implemented these six criteria will be discussed. Monitor tobacco use and prevention policies: Monitoring of tobacco use prevalence has been successfully monitored in Turkey through Global Adult Tobacco Survey, Global Youth Tobacco Survey and Health Professionals Tobacco Use Survey. Nevertheless, monitoring of tobacco industry activities was not successfully implemented. Protect people from tobacco smoke: Smoking was banned in most of the indoor public places in Turkey since 1996, and Turkey became a complete smoke-free country by the exposion of smoke-free places including the hospitality workplaces in 2008. Offer help to quit tobacco use: Although smoking cessation services has been a bit late in Turkey, availability of smoking cessation drugs and the establishment of free quitline services made Turkey successful in this regard. Warn about the dangers of tobacco: Since 1996, all TV channels have a duty of broadcasting programs on harms of tobacco use, not less than 90 minutes in a month and it has been implemented successfully. Additionally written messages indicating harms of tobacco has been printed on the packs since 1988 and pictures was added in 2010. But since the average surface area covered by the messages in less than 50% of the total surface of the pack, Turkey was not regarded as to meet the requirement. Enforce bans on tobacco advertising, promotion and sponsorship: All kinds of tobacco advertisement and promotion was banned by the Law in 1996. But the tobacco products was not in closed boxes at the sales points. Turkey was not found as successful

Synthesis and characterization of nano ZnO rods via microwave assisted chemical precipitation method

Energy Technology Data Exchange (ETDEWEB)

Uma Sangari, N., E-mail: umasangariselvakumar@gmail.com [Department of Chemistry, S.F.R. College for Women, Sivakasi 626123 (India); Chitra Devi, S. [Department of Chemistry, S.F.R. College for Women, Sivakasi 626123 (India)

2013-01-15

A microwave assisted chemical precipitation method has been employed for the synthesis of nano zinc oxide rods by reacting zinc nitrate and potassium hydroxide. The amount of potassium hydroxide was adjusted for three different pHs to achieve ZnO nano rods with varying aspect ratio. The mechanism of growth of nano rods is explained briefly. The average crystallite size of the as synthesized samples was analyzed by means of powder XRD pattern and estimated to vary from 25.6 nm to 43.1 nm. The existence of rods was confirmed using scanning electron microscopy (SEM). The samples were also analyzed using FT-IR. The optical properties of the samples were also studied by means of UV-visible spectra and Room Temperature Photo Luminescence studies. The band gap of the samples was determined from the DRS spectrum. A strong near band emission peaks due to surface defects are observed in the PL spectrum. - Graphical abstract: At the solution pH of 11 and 9, tetrapod-like and flower-like ZnO nano rods were formed along with separated rods respectively due to the formation of activated nuclei of different sizes. Highlights: Black-Right-Pointing-Pointer Increase in alkalinity of the precursor solution results in longer rods. Black-Right-Pointing-Pointer Beyond a saturation limit, the excess of added OH{sup -} ions inhibited the growth of rods. Black-Right-Pointing-Pointer Keeping all parameters the same, the alkalinity can only modify the aspect ratio of the rods and not their morphology.

Control rod drives

International Nuclear Information System (INIS)

Nakamura, Akira.

1984-01-01

Purpose: To enable to monitor the coupling state between a control rod and a control rod drive. Constitution: After the completion of a control rod withdrawal, a coolant pressure is applied to a control rod drive being adjusted so as to raise only the control rod drive and, in a case where the coupling between the control rod drive and the control rod is detached, the former is elevated till it contacts the control rod and then stopped. The actual stopping position is detected by an actual position detection circuit and compared with a predetermined position stored in a predetermined position detection circuit. If both of the positions are not aligned with each other, it is judged by a judging circuit that the control rod and the control rod drives are not combined. (Sekiya, K.)

On the Cooley-Turkey Fast Fourier algorithm for arbitrary factors ...

African Journals Online (AJOL)

Atonuje and Okonta in [1] developed the Cooley-Turkey Fast Fourier transform algorithm and its application to the Fourier transform of discretely sampled data points N, expressed in terms of a power y of 2. In this paper, we extend the formalism of [1] Cookey-Turkey Fast Fourier transform algorithm. The method is developed ...

Implications of Bilingual Development for Specific Language Impairments in Turkey

Science.gov (United States)

Topbas, Seyhun

2011-01-01

The potential impact of bilingualism on children's language development has emerged as a crucial concern for Turkey, but so far it has not been addressed from the point of view of language disorders. This short review examines the potential impact of bilingual language development for language impairments in Turkey, with special emphasis on the…

Review Team Focused Modeling Analysis of Radial Collector Well Operation on the Hypersaline Groundwater Plume beneath the Turkey Point Site near Homestead, Florida

International Nuclear Information System (INIS)

Oostrom, Martinus; Vail, Lance W.

2016-01-01

Researchers at Pacific Northwest National Laboratory served as members of a U.S. Nuclear Regulatory Commission review team for the Florida Power & Light Company's application for two combined construction permits and operating licenses (combined licenses or COLs) for two proposed new reactor units-Turkey Point Units 6 and 7. The review team evaluated the environmental impacts of the proposed action based on the October 29, 2014 revision of the COL application, including the Environmental Report, responses to requests for additional information, and supplemental information. As part of this effort, team members tasked with assessing the environmental effects of proposed construction and operation of Units 6 and 7 at the Turkey Point site reviewed two separate modeling studies that analyzed the interaction between surface water and groundwater that would be altered by the operation of radial collector wells (RCWs) at the site. To further confirm their understanding of the groundwater hydrodynamics and to consider whether certain actions, proposed after the two earlier modeling studies were completed, would alter the earlier conclusions documented by the review team in their draft environmental impact statement (EIS; NRC 2015), a third modeling analysis was performed. The third modeling analysis is discussed in this report.

Elliptical cross section fuel rod study II

International Nuclear Information System (INIS)

Taboada, H.; Marajofsky, A.

1996-01-01

In this paper it is continued the behavior analysis and comparison between cylindrical fuel rods of circular and elliptical cross sections. Taking into account the accepted models in the literature, the fission gas swelling and release were studied. An analytical comparison between both kinds of rod reveals a sensible gas release reduction in the elliptical case, a 50% swelling reduction due to intragranular bubble coalescence mechanism and an important swelling increase due to migration bubble mechanism. From the safety operation point of view, for the same linear power, an elliptical cross section rod is favored by lower central temperatures, lower gas release rates, greater gas store in ceramic matrix and lower stored energy rates. (author). 6 refs., 8 figs., 1 tab

Control rod assembly

International Nuclear Information System (INIS)

Takahashi, Akio.

1982-01-01

Purpose: To enable reliable insertion and drops of control rods, as well as insure a sufficient flow rate of coolants flowing through the control rods for attaining satisfactory cooling thereof to enable relexation of thermal stress resulted to rectifying mechanisms or the likes. Constitution: To the outer circumference of a control rod contained vertically movably within a control rod guide tube, resistive members are retractably provided in such a way as to project to close the gap between outer circumference of the control rod and the inner surface of the control rod guide tube upon engagement of a gripper of control rod drives, and retract upon release of the engagement of the gripper. Thus, since the resistive members project to provide a greater resistance to the coolants flowing between them and the control rod guide tube in the normal operation where the gripper is engaged to drive the control rod by the control rod drives, a major part of the coolant flowing into the control rod guide tube flows into the control rod. This enables to cool the control rod effectively and make the temperature distribution uniform for the coolant flowing from the upper end of the control rod guide tube to thereby attain the relaxation of the thermal stress resulted in the rectifying mechanisms or the likes. (Moriyama, K.)

Device for coupling a control rod and control rod drive

International Nuclear Information System (INIS)

Nishioka, Kazuya.

1975-01-01

Object: To obtain simple and reliable coupling between a control rod and control rod drive by equipping the lower end of the control rod with an extension provided with lateral protuberances and forming the upper end of an index tube with a recess provided with lateral holes. Structure: The tapering central extension of the control rod is inserted into the recess by lowering the control rod, and then it is further inserted by causing frictional movement of the inclined surfaces of lateral protuberances in frictional contact with guide surfaces. When the lateral protuberances are brought into contact with a stepped portion, the control rod is rotated to fit the lateral protuberances into the lateral holes. In this way, the control rod is coupled to the index tube of the control rod drive. (Yoshino, Y.)

Temperature and Stresses Estimation in Reactivity Control Rods for CAREM-25 Reactor

International Nuclear Information System (INIS)

Markiewicz, Mario; Estevez, Esteban

2000-01-01

The reactivity control rods are a critical component regarding safety.Its correct operation when required must be ensured.For this purpose, this component must maintain its operating capacity during all its residence time and under any foreseen operation condition.To evaluate the behaviour of reactivity control rods, it is necessary to analyse the demands they are exposed to, determining from the mechanical point of view, the residence time in the reactor core.In this report, using analytical calculations, the parameters affecting the performance of the reactivity control rods are analysed, with the objective of determine from the mechanical point of view, its behaviour and residence time

Expert system for control rod programming of boiling water reactors

International Nuclear Information System (INIS)

Fukuzaki, T.; Yoshida, K.; Kobayashi, Y.; Matsuura, H.; Hoshi, K.

1986-01-01

Control rod programming, one of the main tasks in reactor core management of boiling water reactors (BWRs), can be successfully accomplished by well-experienced engineers. By use of core performance evaluation codes, their knowledge plays the main role in searching through optimal control rod patterns and exposure points for adjusting notch positions and exchanging rod patterns. An expert system has been developed, based on a method of knowledge engineering, to lighten the engineer's load in control rod programming. This system utilizes an inference engine suited for planning/designing problems, and stores the knowledge of well-experienced engineers in its knowledge base. In this report, the inference engine, developed considering the characteristics of the control rod programming, is introduced. Then the constitution and function of the expert system are discussed

Control rod displacement

International Nuclear Information System (INIS)

Nakazato, S.

1987-01-01

This patent describes a nuclear reactor including a core, cylindrical control rods, a single support means supporting the control rods from their upper ends in spaced apart positions and movable for displacing the control rods in their longitudinal direction between a first end position in which the control rods are fully inserted into the core and a second end position in which the control rods are retracted from the core, and guide means contacting discrete regions of the outer surface of each control rod at least when the control rods are in the vicinity of the second end position. The control rods are supported by the support means for longitudinal movement without rotation into and out of the core relative to the guide means to thereby cause the outer surface of the control rods to experience wear as a result of sliding contact with the guide means. The support means are so arranged with respect to the core and the guide means that it is incapable of rotation relative to the guide means. The improvement comprises displacement means being operatively coupled to a respective one of the control rods for periodically rotating the control rod in a single angular direction through an angle selected to change the locations on the outer surfaces of the control rods at which the control rods are contacted by the guide means during subsequent longitudinal movement of the control rods

Rod displacement measurements by x-ray CT and its impact on thermal-hydraulics in tight-lattice rod bundle (Joint research)

International Nuclear Information System (INIS)

Mitsutake, Toru; Misawa, Takeharu; Kureta, Masatoshi; Akimoto, Hajime

2005-06-01

In tight-lattice simulated rod bundles with about 1 mm gap between rods, a rod displacement might affect thermal-hydraulic characteristics since the displacement has a strong impact on the flow area change along the heated section. It should be important to estimate how large the rod position displacement could quantitatively affect critical power for the tight-lattice rod bundle from the point of improvement of prediction capability of subchannel analysis. In the present study, the inside-structure observation of the simulated seven-rod bundle of Reduced Moderation Water Reactor (RMWR) was made through the whole length of the test assembly. Based on the measured rod position data, the relation between the rod position displacement and the heat transfer characteristics was investigated experimentally and through the two kinds of subchannel analysis, the nominal rod position case and the measured rod position case, the effect on the predicted critical power was estimated. The high-energy X-ray computer tomograph (CT) of Fuels Monitoring Facilities (FMF) at the O-arai Engineering Center in Japan Nuclear Cycle Institute (JNC) was applied for the inside-structure observation of the test assembly. The CT view of the cross sections within the test assembly assured the hexagonal rod position arrangement was almost the same as expected by design. The measured data with the X-ray CT facility showed that all rod displacements were small, 0.5 millimeters at maximum and 0.2 millimeters in average. In the heat transfer experiments for the seven-rod bundle, the boiling transition (BT) position and the rod surface temperature behavior was measured. All thermocouples on the center rod downstream from the BT-onset axial height showed almost simultaneous temperature increase due to BT. And the thermocouples located on the same axial heights showed quite similar time-variation behaviors in the vapor cooling heat transfer regime. These results demonstrated the effect of the

Morphoelastic rods. Part I: A single growing elastic rod

KAUST Repository

Moulton, D.E.

2013-02-01

A theory for the dynamics and statics of growing elastic rods is presented. First, a single growing rod is considered and the formalism of three-dimensional multiplicative decomposition of morphoelasticity is used to describe the bulk growth of Kirchhoff elastic rods. Possible constitutive laws for growth are discussed and analysed. Second, a rod constrained or glued to a rigid substrate is considered, with the mismatch between the attachment site and the growing rod inducing stress. This stress can eventually lead to instability, bifurcation, and buckling. © 2012 Elsevier Ltd. All rights reserved.

Morphoelastic rods. Part I: A single growing elastic rod

KAUST Repository

Moulton, D.E.; Lessinnes, T.; Goriely, A.

2013-01-01

A theory for the dynamics and statics of growing elastic rods is presented. First, a single growing rod is considered and the formalism of three-dimensional multiplicative decomposition of morphoelasticity is used to describe the bulk growth of Kirchhoff elastic rods. Possible constitutive laws for growth are discussed and analysed. Second, a rod constrained or glued to a rigid substrate is considered, with the mismatch between the attachment site and the growing rod inducing stress. This stress can eventually lead to instability, bifurcation, and buckling. © 2012 Elsevier Ltd. All rights reserved.

Control rod drive

International Nuclear Information System (INIS)

Hawke, B.C.

1986-01-01

A reactor core, one or more control rods, and a control rod drive are described for selectively inserting and withdrawing the one or more control rods into and from the reactor core, which consists of: a support structure secured beneath the reactor core; control rod positioning means supported by the support structure for movably supporting the control rod for movement between a lower position wherein the control rod is located substantially beneath the reactor core and an upper position wherein at least an upper portion of the control rod extends into the reactor core; transmission means; primary drive means connected with the control rod positioning means by the transmission means for positioning the control rod under normal operating conditions; emergency drive means for moving the control rod from the lower position to the upper position under emergency conditions, the emergency drive means including a weight movable between an upper and a lower position, means for movably supporting the weight, and means for transmitting gravitational force exerted on the weight to the control rod positioning means to move the control rod upwardly when the weight is pulled downwardly by gravity; the transmission means connecting the control rod positioning means with the emergency drive means so that the primary drive means effects movement of the weight and the control rod in opposite directions under normal conditions, thus providing counterbalancing to reduce the force required for upward movement of the control rod under normal conditions; and restraint means for restraining the fall of the weight under normal operating conditions and disengaging the primary drive means to release the weight under emergency conditions

Flame spread along thermally thick horizontal rods

Science.gov (United States)

Higuera, F. J.

2002-06-01

An analysis is carried out of the spread of a flame along a horizontal solid fuel rod, for which a weak aiding natural convection flow is established in the underside of the rod by the action of the axial gradient of the pressure variation that gravity generates in the warm gas surrounding the flame. The spread rate is determined in the limit of infinitely fast kinetics, taking into account the effect of radiative losses from the solid surface. The effect of a small inclination of the rod is discussed, pointing out a continuous transition between upward and downward flame spread. Flame spread along flat-bottomed solid cylinders, for which the gradient of the hydrostatically generated pressure drives the flow both along and across the direction of flame propagation, is also analysed.

Cultural Tourism Tours and Main Routes Towards Turkey

Directory of Open Access Journals (Sweden)

Veysi GÜNAL

2009-06-01

Full Text Available Today, the tourism has become a important industry. Certainly, the most important international actors af this industry are tour operators. The tour operators which realize about 75 percent of the total tourism activity to Turkey have taken a very important mission from the point of Turkey tourism. The, Germany, Netherlands, England and USA tour operators, which have made the important part of the tours to our country, have also an important position in organizating cultural tour. When the cultural tours, which have been planned to Turkey by this countries, have been studied it is seen that these tours have containied more mass tourism areas or near areas of these region. It can be said that Turkey’s not marketing its tourism correctly has be effective in this subject. With this research, it has been studied how the cultural attractions in Turkey have been perceived, consumed and marketed by abroad tour operators.

Review Team Focused Modeling Analysis of Radial Collector Well Operation on the Hypersaline Groundwater Plume beneath the Turkey Point Site near Homestead, Florida

Energy Technology Data Exchange (ETDEWEB)

Oostrom, Martinus [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Vail, Lance W. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-08-01

Researchers at Pacific Northwest National Laboratory served as members of a U.S. Nuclear Regulatory Commission review team for the Florida Power & Light Company’s application for two combined construction permits and operating licenses (combined licenses or COLs) for two proposed new reactor units—Turkey Point Units 6 and 7. The review team evaluated the environmental impacts of the proposed action based on the October 29, 2014 revision of the COL application, including the Environmental Report, responses to requests for additional information, and supplemental information. As part of this effort, team members tasked with assessing the environmental effects of proposed construction and operation of Units 6 and 7 at the Turkey Point site reviewed two separate modeling studies that analyzed the interaction between surface water and groundwater that would be altered by the operation of radial collector wells (RCWs) at the site. To further confirm their understanding of the groundwater hydrodynamics and to consider whether certain actions, proposed after the two earlier modeling studies were completed, would alter the earlier conclusions documented by the review team in their draft environmental impact statement (EIS; NRC 2015), a third modeling analysis was performed. The third modeling analysis is discussed in this report.

Replacement rod

International Nuclear Information System (INIS)

Hatfield, S.C.

1989-01-01

This patent describes in an elongated replacement rod for use with fuel assemblies of the type having two end fittings connected by guide tubes with a plurality of rod and guide tube cell defining spacer grids containing rod support features and mixing vanes. The grids secured to the guide tubes in register between the end fittings at spaced intervals. The fuel rod comprising: an asymmetrically beveled tip; a shank portion having a straight centerline; and a permanently diverging portion between the tip and the shank portion

Water rod

International Nuclear Information System (INIS)

Kashiwai, Shin-ichi; Yokomizo, Osamu; Orii, Akihito.

1992-01-01

In a reactor core of a BWR type reactor, the area of a flow channel in a lower portion of a downcoming pipe for downwardly releasing steams present at the top portion in a water rod is increased. Further, a third coolant flow channel (an inner water rod) is disposed in an uprising having an exit opened near the inlet of the water rod and an inlet opened at the outside near the top portion of the water and having an increase flow channel area in the upper portion. The downcoming pipe in the water rod is filled with steams, and the void ratio is increased by so much as the flow channel area of the downcoming pipe is increased. Since the pressure difference between the inlet and the exit of the inner water rod is greater than the pressure difference between the inlet and the exit of the water rod, most of water flown into the inner water rod is discharged out of the exit in the form of water as it is. Since the area of the flow channel is increased in the portion of the inner water rod, void efficiency in the upper portion of the reactor core is decreased by so much. Since the void ratio is thus increased in the lower portion and the void efficiency is decreased in the upper portion of the reactor core, axial void distribution can be flattened. (N.H.)

Physics calculations for the RIA 1-3 irradiated rod test

International Nuclear Information System (INIS)

Young, T.E.

1981-06-01

The RIA 1-3 test would employ a square array of four pre-irradiated BWR rods to provide information on fuel failure modes and consequences of postulated Reactivity Initiated Accidents in power reactors. Calculations were done to: (1) predict R-O power distributions in the test rods for thermal-hydraulic and fuel-failure analysis; and (2) predict the steady-state and transient ratios of test fuel energy deposition to core energy deposition (Figures of Merit). Fission distributions for the test were computed with the RAFFL Monte Carlo code using an external neutron current source from a complete-reactor radial calculation with the SCAMP S/sub n/ code. Energies per fission for the rods were computed using the SINBAD buildup and depletion code, the GAMSOR gamma ray source code, and the QAD-BSA point-kernel shielding code. The calculated rod average-to-test average energy deposition ratios are 0.99, 0.99, and 0.97 for the rods irradiated to approximately 12 CWd/tu, and 1.04 for the rod irradiated to 4.8 GWd/tu. The maximum deviation of the power density of 1/12-rod azimuthal segments from the rod average is 4%. For an estimated control rod position of 0.591 m withdrawn the predicted radial average energy deposition at the axial peak in an average test rod is 1.71 (kW/m)/MW during preconditioning, and 1.84 (kJ/kg UO 2 ) MW.S during the burst. 16 figures, 7 tables

Control rod

International Nuclear Information System (INIS)

Igarashi, Takao; Yoshimoto, Yuichiro; Sugawara, Satoshi; Fukumoto, Takashi; Endo, Zen-ichiro; Saito, Shozo; Shinpo, Katsutoshi; Nishimura, Akira; Ozawa, Michihiro

1988-01-01

Purpose: To provide a sufficient shutdown margin upon reactor shutdown, prevent sheath deformation without decreasing neutron absorbents and prevent impact shocks exerted to structural materials. Constitution: The control rod of the present invention comprises a neutron absorption region, a sheath deformation means attached to the side wall and means for restricting and supporting axial movement of the neutron absorbent rod. Then, the amount of absorptive nuclei chained absorbents in the lower region is reduced than that in the upper region. In this way, effective neutron absorbing performance can be obtained relative to the neutron importance distribution during reactor shutdown. In addition, since the operationability is improved by reducing the weight of the control rod and the absorptive nuclei chained neutron abosrbers are used, mechanical nuclear life of the control rod can be increased. Thus, it is possible to prevent the outward deformation of the sheath, as well as prevent collision between the neutron absorber rod and the structural material on the side of inserting the control rod generated upon reactor scram by a simple structure. (Kamimura, M.)

THE ASSESSMENT OF GEOTHERMAL POTENTIAL OF TURKEY BY MEANS OF HEAT FLOW ESTIMATION

Directory of Open Access Journals (Sweden)

UĞUR AKIN

2014-12-01

Full Text Available In this study, the heat flow distribution of Turkey was investigated in the interest ofexploring new geothermal fields in addition to known ones. For this purposes, thegeothermal gradient was estimated from the Curie point depth map obtained from airbornemagnetic data by means of power spectrum method. By multiplying geothermal gradientwith thermal conductivity values, the heat flow map of Turkey was obtained. The averagevalue in the heat flow map of Turkey was determined as 74 mW/m2. It points out existenceof resources of geothermal energy larger than the average of the world resources. in termsof geothermal potential, the most significant region of Turkey is the Aydin and itssurrounding with a value exceeding 200 mW/m2. On the contrary, the value decreasesbelow 30 mW/m2in the region bordered by Aksaray, Niğde, Karaman and Konya. Thenecessity of conducting a detailed additional studies for East Black sea, East and SoutheastAnatolia is also revealed

Renewable energy market conditions and barriers in Turkey

International Nuclear Information System (INIS)

Nalan, Cicek Bezir; Murat, Oeztuerk; Nuri, Oezek

2009-01-01

Decentralized wind, hydropower, biogas and biomass, geothermal, solar thermal and solar electricity energy systems are the most commonly found renewable energy technologies promoted for rural energy supply within sustainable developments programs. They are, therefore, seen to have a central place in the practice of sustainable development and in allowing less development countries to bypass the environmentally damaging fossil fuel intensive paths made by industrialized countries. On the political front, many less development countries are critical of pressure on them to adopt environmental energy technologies. Turkey is situated the meeting point of three continents (Asia, Europe and Africa) and stands as a bridge between Asia and Europe. The country is located in southeastern Europe and southwestern Asia. As Turkey's economy has expanded in recent years, the consumption of primary energy has increased. Presently in order to increase the energy production from domestic energy resources, decrease the use of fossil fuels as well as reduce of green house gas emissions different renewable energy sources are used for energy production in Turkey. The share of energy production from renewable energy sources has increased during the last 10 years. Turkey must import most of the energy to meet her needs. Turkey also has a large potential for renewable energies. The lack of knowledge about renewable energy technologies by most policy-makers, potential consumers, and energy firm managers has played against renewable energy developments. The paper presents renewable energy used in Turkey and Europe Union and evaluation of the market conditions and barriers of renewable energy use in Turkey. (author)

Control rod drives

International Nuclear Information System (INIS)

Futatsugi, Masao.

1980-01-01

Purpose: To secure the reactor operation safety by the provision of a fluid pressure detecting section for control rod driving fluid and a control rod interlock at the midway of the flow pass for supplying driving fluid to the control rod drives. Constitution: Between a driving line and a direction control valve are provided a pressure detecting portion, an alarm generating device, and a control rod inhibition interlock. The driving fluid from a driving fluid source is discharged by way of a pump and a manual valve into the reactor in which the control rods and reactor fuels are contained. In addition, when the direction control valve is switched and the control rods are inserted and extracted by the control rod drives, the pressure in the driving line is always detected by the pressure detection section, whereby if abnormal pressure is resulted, the alarm generating device is actuated to warn the abnormality and the control rod inhibition interlock is actuated to lock the direction control valve thereby secure the safety operation of the reactor. (Seki, T.)

Control rod drives

International Nuclear Information System (INIS)

Oonuki, Koji.

1981-01-01

Purpose: To increase the driving speed of control rods at rapid insertion with an elongate control rod and an extension pipe while ensuring sufficient buffering performance in a short buffering distance, by providing a plurality of buffers to an extension pipe between a control rod drive source and a control rod in LMFBR type reactor. Constitution: First, second and third buffers are respectively provided to an acceleration piston, an extension pipe and a control rod respectively and the insertion positions for each of the buffers are displaced orderly from above to below. Upon disconnection of energizing current for an electromagnet, the acceleration piston, the extension pipe and the control rod are rapidly inserted in one body. The first, second and third buffers are respectively actuated at each of their falling strokes upon rapid insertion respectively, and the acceleration piston, the extension pipe and the control rod receive the deceleration effect in the order correspondingly. Although the compression force is applied to the control rod only near the stroke end, it does not cause deformation. (Kawakami, Y.)

Key developments of a rod control system - 15101

International Nuclear Information System (INIS)

Pouillot, M.; Jegou, H.; Duthou, A.

2015-01-01

The aim of the Rod Control System is to carry out the insertion and withdrawal of control rod clusters to provide the power required by the grid (G-mode control), to control the temperature of the reactor, or to provide negative reactivity margin when the reactor is shut down. The rod control system is not classified important for safety, but its correct operation is essential for the availability of the reactor, as the spurious drop of a single cluster usually results in a reactor trip. Rolls-Royce has been designing, manufacturing and providing rod control systems since 1977, in France, China, Belgium, Korea, and South Africa, as an original manufacturer and for modernization projects. All the corresponding nuclear units share the following features, key points for the system design: -) The power source is a three-phased 260 Vac with neutral, provided by zigzag-coupled alternators; -) The Control Rod Drive Mechanisms (CRDM) are 'three-coil type': Stationary Gripper (SG), Movable Gripper (MG) and Lift Coil (LC); -) Rod clusters are arranged in banks and sub-banks, the bank being composed of one or two sub-banks and a sub-bank is a set of 4 clusters moved simultaneously, the central cluster being an exception; and -) Most of those reactors are operated in G-mode (load following). (authors)

Microbiological quality of pastrami and associated surfaces at the point of sale in Kayseri, Turkey.

Science.gov (United States)

Yildirim, Y; Ertas Onmaz, N; Gonulalan, Z; Al, S; Yildirim, A; Karadal, F; Hizlisoy, H; Pamuk, Ş

2017-05-01

The aim of this study is to trace the possible relations between the hygienic status of slicing utensils and the microbiological quality of pastrami. A total of 75 pastrami retail markets were visited in Kayseri, Turkey, where the pastrami (a ready-to-eat meat product) is commonly produced and consumed. Sliced pastrami, the cutting board and knife surface swabs were collected from each pastrami retail point to trace possible sources of contamination. Samples were analysed for the presence of total viable counts (TVC), total coliforms, Escherichia coli, members of Enterobacteriaceae, Staphylococcus aureus and Listeria spp. In addition, pastrami samples were analysed for sulphite-reducing Clostridium spp. and Toxoplasma gondii. When compared with the target values of related literatures, a total of 6 (8%) pastrami samples were found unsatisfactory as a result of TVC (5.3%), Enterobacteriaceae (5.3%), E. coli (2.6%), S. aureus (2.6%), Listeria spp. (2.6%) and Listeria monocytogenes (1.3%) contaminations. No T. gondii positivity was observed among the pastrami samples. None of the cutting board and knife surface swabs were found to harbour TVC level >10 3  cfu/cm 2 , E. coli and L. monocytogenes. For the total coliforms, 7 (9.3%) and 5 (6.6%) of cutting board and knife surface swabs were found to exceed the target value (point of pastrami sale. The conditions at retail points must be monitored and inspections should be tightened to protect public health. Copyright © 2017 The Royal Society for Public Health. Published by Elsevier Ltd. All rights reserved.

Comparison of Early Childhood Education (Preschool Education) in Turkey and OECD Countries

Science.gov (United States)

Ozgan, Habib

2010-01-01

In this study, it was aimed to evaluate how the difference the early childhood education in Turkey and OECD countries. The outstanding point evaluated by the teachers about the difference between the education in Turkey and that in OECD countries and the conditions needing to be improved was the compare of age groups benefiting from the services…

Impact of mesh points number on the accuracy of deterministic calculations of control rods worth for Tehran research reactor

International Nuclear Information System (INIS)

Boustani, Ehsan; Amirkabir University of Technology, Tehran; Khakshournia, Samad

2016-01-01

In this paper two different computational approaches, a deterministic and a stochastic one, were used for calculation of the control rods worth of the Tehran research reactor. For the deterministic approach the MTRPC package composed of the WIMS code and diffusion code CITVAP was used, while for the stochastic one the Monte Carlo code MCNPX was applied. On comparing our results obtained by the Monte Carlo approach and those previously reported in the Safety Analysis Report (SAR) of Tehran research reactor produced by the deterministic approach large discrepancies were seen. To uncover the root cause of these discrepancies, some efforts were made and finally was discerned that the number of spatial mesh points in the deterministic approach was the critical cause of these discrepancies. Therefore, the mesh optimization was performed for different regions of the core such that the results of deterministic approach based on the optimized mesh points have a good agreement with those obtained by the Monte Carlo approach.

Impact of mesh points number on the accuracy of deterministic calculations of control rods worth for Tehran research reactor

Energy Technology Data Exchange (ETDEWEB)

Boustani, Ehsan [Nuclear Science and Technology Research Institute (NSTRI), Tehran (Iran, Islamic Republic of); Amirkabir University of Technology, Tehran (Iran, Islamic Republic of). Energy Engineering and Physics Dept.; Khakshournia, Samad [Amirkabir University of Technology, Tehran (Iran, Islamic Republic of). Energy Engineering and Physics Dept.

2016-12-15

In this paper two different computational approaches, a deterministic and a stochastic one, were used for calculation of the control rods worth of the Tehran research reactor. For the deterministic approach the MTRPC package composed of the WIMS code and diffusion code CITVAP was used, while for the stochastic one the Monte Carlo code MCNPX was applied. On comparing our results obtained by the Monte Carlo approach and those previously reported in the Safety Analysis Report (SAR) of Tehran research reactor produced by the deterministic approach large discrepancies were seen. To uncover the root cause of these discrepancies, some efforts were made and finally was discerned that the number of spatial mesh points in the deterministic approach was the critical cause of these discrepancies. Therefore, the mesh optimization was performed for different regions of the core such that the results of deterministic approach based on the optimized mesh points have a good agreement with those obtained by the Monte Carlo approach.

Control rod cluster with removable rods for nuclear fuel assembly

International Nuclear Information System (INIS)

Denizou, J.P.

1989-01-01

For each removable control rod, the open end section of the sleeve has a certain length of reduced diameter with openings in its wall. The top end of the rod is joined to an extension tube that surrounds the shaft over part of its lenght. This extension tube fits over the reduced part of the sleeve when the shaft is screwed into the bore of the sleeve. Rotation of the rod in the sleeve is prevented by deforming the extension tube locally in the openings of the end part of the sleeve. The rod is dismantled by exerting a torque on it using a gripping area near the end of the rod [fr

Electric-field Induced Microdynamics of Charged Rods

Directory of Open Access Journals (Sweden)

Kyongok eKang

2014-12-01

Full Text Available Electric-field induced phase/state transitions are observed in AC electric fields with small amplitudes and low frequencies in suspensions of charged fibrous viruses (fd, which are model systems for highly charged rod-like colloids. Texture- and particle-dynamics in these field-induced states, and on crossing transition lines, are explored by image time-correlation and dynamic light scattering, respectively. At relatively low frequencies, starting from a system within the isotropic-nematic coexistence region, a transition from a nematic to a chiral nematic is observed, as well as a dynamical state where nematic domains melt and reform. These transitions are preliminary due to field-induced dissociation/association of condensed ions. At higher frequencies a uniform state is formed that is stabilized by hydrodynamic interactions through field-induced electro-osmotic flow where the rods align along the field direction. There is a point in the field-amplitude versus frequency plane where various transition lines meet. This point can be identified as a non-equilibrium critical point, in the sense that a length scale and a time scale diverge on approach of that point. The microscopic dynamics exhibits discontinuities on crossing transition lines that were identified independently by means of image and signal correlation spectroscopy.

Control rod drive mechanism

International Nuclear Information System (INIS)

Nakamura, Akira.

1981-01-01

Purpose: To ensure the scram operation of a control rod by the reliable detection for the position of control rods. Constitution: A permanent magnet is provided to the lower portion of a connecting rod in engagement with a control rod and a tube having a plurality of lead switches arranged axially therein in a predetermined pitch is disposed outside of the control rod drives. When the control rod moves upwardly in the scram operation, the lead switches are closed successively upon passage of the permanent magnet to operate the electrical circuit provided by way of each of the lead switches. Thus, the position for the control rod during the scram can reliably be determined and the scram characteristic of the control rod can be recognized. (Furukawa, Y.)

Measurements of two-phase flow patterns in a 4 x 4 rod bundle

International Nuclear Information System (INIS)

Akio tomiyama; Akira Sou; Shigeo Hosokawa; Masato Mitsuhashi; Kohei Noda; Yasushi Tsubo; Kaichiro Mishima; Yoshiro Kudo

2005-01-01

Air-water two-phase flow patterns in a 4 x 4 square lattice rod bundle consisting of an acrylic channel box of 68 mm in width and transparent rods of 12 mm in diameter were measured by utilizing FEP (fluorinated ethylene propylene) tubes for the rods. The FEP possesses the same refractive index with water, and therefore, whole flow patterns in the bundle and local flow patterns in subchannels were visualized with little optical distortion. In addition to the visualization, transmission rates of laser beam from one rod to its opponent rod and two-point correlation coefficients of phase indicator functions were measured to examine the feasibility of objective identification of flow patterns in subchannels. The ranges of liquid and gas volume fluxes, JL and JG, were 0.1 < JL < 2.0 m/s and 0.04 < JG < 8.85 m/s, respectively. As a result, the following conclusions were obtained: (1) slug flow pattern does not appear in the rod bundle and bubbly flow would directly transit to churn flow, (2) the measured boundary between bubbly and churn flows is close to the boundary between bubbly and slug flows given by Mishima and Ishii's flow pattern transition model, (3) critical void fraction causing bubbly to churn flow transition depends on a subchannel, i.e., about 0.3 for inner subchannels, about 0.2 for side subchannels and about 0.1 for corner subchannels, and (4) the two-point correlation coefficient of phase indicator functions for two inner subchannels shows a steep increase at the bubbly to churn flow transition, which, in turn, means that the two-point correlation is an appropriate indicator for detecting this transition. (authors)

Control rod drives

International Nuclear Information System (INIS)

Hayakawa, Hiroyasu.

1979-01-01

Purpose: To enable rapid control in a simple circuit by providing a motor control device having an electric capacity capable of simultaneously driving all of the control rods rapidly only in the inserting direction as well as a motor controlling device capable of fine control for the insertion and extraction at usual operation. Constitution: The control rod drives comprise a first motor control device capable of finely controlling the control rods both in inserting and extracting directions, a second motor control device capable of rapidly driving the control rods only in the inserting direction, and a first motor switching circuit and a second motor switching circuit switched by switches. Upon issue of a rapid insertion instruction for the control rods, the second motor switching circuit is closed by the switch and the second motor control circuit and driving motors are connected. Thus, each of the control rod driving motors is driven at a high speed in the inserting direction to rapidly insert all of the control rods. (Yoshino, Y.)

Fission reactor control rod

International Nuclear Information System (INIS)

Irie, Tomoo.

1991-01-01

The present invention concerns a control rod in a PWR type reactor. A control rod has an inner cladding tube and an outer cladding tube disposed coaxially, and a water draining hole is formed at the inside of the inner cladding tube. Neutron absorbers are filled in an annular gap between the outer cladding tube and the inner cladding tube. The water draining hole opens at the lower end thereof to the top end of the control rod and at the upper end thereof to the side of the upper end plug of the control rod. If the control rod is dropped to a control rod guide thimble for reactor scram, coolants from the control rod guide thimble are flown from the lower end of the water draining hole and discharged from the upper end passing through the water draining hole. In this way, water from the control rod guide thimble is removed easily when the control rod is dropped. Further, the discharging amount of water itself is reduced by the provision of the water draining hole. Accordingly, sufficient control rod dropping speed can be attained. (I.N.)

Fuel rod simulator effects in flooding experiments single rod tests

International Nuclear Information System (INIS)

Nishida, M.

1984-09-01

The influence of a gas filled gap between cladding and pellet on the quenching behavior of a PWR fuel rod during the reflood phase of a LOCA has been investigated. Flooding experiments were conducted with a short length electrically heated single fuel rod simulator surrounded by glass housing. The gap of 0.05 mm width between the Zircaloy cladding and the internal Al 2 O 3 pellets of the rod was filled either wit helium or with argon to vary the radial heat resistance across the gap. This report presents some typical data and an evaluation of the reflood behavior of the fuel rod simulator used. The results show that the quench front propagates faster for increasing heat resistance in the gap between cladding and heat source of the rod. (orig.) [de

Maximum/minimum asymmetric rod detection

International Nuclear Information System (INIS)

Huston, J.T.

1990-01-01

This patent describes a system for determining the relative position of each control rod within a control rod group in a nuclear reactor. The control rod group having at least three control rods therein. It comprises: means for producing a signal representative of a position of each control rod within the control rod group in the nuclear reactor; means for establishing a signal representative of the highest position of a control rod in the control rod group in the nuclear reactor; means for establishing a signal representative of the lowest position of a control rod in the control rod group in the nuclear reactor; means for determining a difference between the signal representative of the position of the highest control rod and the signal representative of the position of the lowest control rod; means for establishing a predetermined limit for the difference between the signal representative of the position of the highest control rod and the signal representative of the position of the lowest control rod; and means for comparing the difference between the signals with the predetermined limit. The comparing means producing an output signal when the difference between the signals exceeds the predetermined limit

Control rod drives

International Nuclear Information System (INIS)

Hayakawa, Hiroyasu; Kawamura, Atsuo.

1979-01-01

Purpose: To reduce pellet-clad mechanical interactions, as well as improve the fuel safety. Constitution: In the rod drive of a bwr type reactor, an electric motor operated upon intermittent input such as of pulse signals is connected to a control rod. A resolver for converting the rotational angle of the motor to electric signals is connected to the rotational shaft of the motor and the phase difference between the output signal from the resolver and a reference signal is adapted to detect by a comparator. Based on the detection result, the controller is actuated to control a motor for control rod drive so that fine control for the movement of the control rod is made possible. This can reduce the moving distance of the control rod, decrease the thermal stress applied to the control rod and decrease the pellet clad mechanical interaction failures due to thermal expansion between the cladding tube and the pellets caused by abrupt changes in the generated power. (Furukawa, Y.)

Penetrating abdomino-thoracic injury with an iron rod: An anaesthetic challenge

Directory of Open Access Journals (Sweden)

Kiranpreet Kaur

2014-01-01

Full Text Available Penetrating abdomino-thoracic injuries are potentially life-threatening due to the associated haemorrhagic shock and visceral injury. The management of these injuries poses specific challenges in pre-hospital care, transport, and management strategies. We report a 35-year-old male having impalement injury of the left thorax and left upper arm with a metallic rod used for construction of the house after a fall from height. One rod penetrated thorax from left shoulder and exit point was present just above the iliac crest and second rod was seen piercing left upper arm. Patient was successfully managed without any intraoperative, post-operative surgical complications, neurological damage or permanent injuries.

Status of rod consolidation

International Nuclear Information System (INIS)

Bailey, W.J.

1985-04-01

Two of the factors that need to be taken into account with rod consolidation are (1) the effects on rods from their removal from the fuel assembly and (2) the effects on rods as a result of the consolidation process. Potential components of both factors are described in the report. Discussed under (1) are scratches on the fuel rod surfaces, rod breakage, crud, extended burnup, and possible cladding embrittlement due to hydrogen injection at BWRs. Discussed under (2) are the increased water temperature (less than 10 0 C) because of closer packing of the rods, formation of crevices between rods in the close-packed mode, contact with dissimilar metals, and the potential for rapid heating of fuel rods following the loss of water from a spent fuel storage pool. Another factor that plays an important role in rod consolidation is the cost of disposal of the nonfuel-bearing components of the fuel assembly. Also, the dose rate from the components - especially Inconel spacer grids - can affect the handling procedures. Several licensing issues that exist are described. A list of recommendations is provided. 98 refs., 5 figs., 5 tabs

From MIPS to Vicsek: A comprehensive phase diagram for self-propelled rods

Science.gov (United States)

Shi, Xiaqing

Self-propelled rods interacting by volume exclusion is one of the simplest active matter systems. Despite years of effort, no comprehensive picture of their phase diagram is available. Furthermore, results on explicit rods are so far largely disconnected from those obtained on the relatively better understood cases of motility induced phase separation (MIPS) of (usually) isotropic active particles, and from our current knowledge of Vicsek-style aligning point particles. In this talk, I will present a complete phase diagram of a generic model of self-propelled rods and show how it is connected to both MIPS and Vicsek worlds.

Control rod drive

International Nuclear Information System (INIS)

Okutani, Tetsuro.

1988-01-01

Purpose: To provide a simple and economical control rod drive using a control circuit requiring no pulse circuit. Constitution: Control rods in a BWR type reactor are driven by hydraulic pressure and inserted or withdrawn in the direction of applying the hydraulic pressure. The direction of the hydraulic pressure is controlled by a direction control valve. Since the driving for the control rod is extremely important in view of the operation, a self diagnosis function is disposed for rapid inspection of possible abnormality. In the present invention, two driving contacts are disposed each by one between the both ends of a solenoid valve of the direction control valve for driving the control rod and the driving power source, and diagnosis is conducted by alternately operating them. Therefore, since it is only necessary that the control circuit issues a driving instruction only to one of the two driving contacts, the pulse circuit is no more required. Further, since the control rod driving is conducted upon alignment of the two driving instructions, the reliability of the control rod drive can be improved. (Horiuchi, T.)

Pulsed eddy current inspection system for nondestructive examination of irradiated fuel rods

International Nuclear Information System (INIS)

Yancey, M.E.

1979-01-01

An inspection system has been developed for nondestructive examination of irradiated fuel rods utilizing pulsed eddy current techniques. The system employs an encircling type pulsed eddy current transducer capable of sensing small defects located on both the inner and outer diameter fuel rod surfaces during a single scan. Pulsed eddy current point probes are used to provide fuel rod wall thikness data and an indication of radial defect location. Two linear variable differential transformers are used to provide information on fuel rod diameter variation. A microprocessor based control system is used to automatically scan fuel rods up to 4.06 meters in length at predetermined radial locations. Defects as small as 0.005 cm deep by 0.254 cm long by 0.005 cm wide have been detected on outside diameter surfaces of a 1.43 cm outside diameter fuel rod cladding with a 0.094 cm wall thickness and 0.010 cm deep by 0.254 cm long by 0.005 cm wide on the inside diameter surface

Control rod withdrawal monitoring device

International Nuclear Information System (INIS)

Ebisuya, Mitsuo.

1984-01-01

Purpose: To prevent the power ramp even if a plurality of control rods are subjected to withdrawal operation at a time, by reducing the reactivity applied to the reactor. Constitution: The control rod withdrawal monitoring device is adapted to monitor and control the withdrawal of the control rods depending on the reactor power and the monitoring region thereof is divided into a control rod group monitoring region a transition region and a control group monitoring not interfere region. In a case if the distance between a plurality of control rods for which the withdrawal positions are selected is less than a limiting value, the coordinate for the control rods, distance between the control rods and that the control rod distance is shorter are displayed on a display panel, and the withdrawal for the control rods are blocked. Accordingly, even if a plurality of control rods are subjected successively to the withdrawal operation contrary to the control rod withdrawal sequence upon high power operation of the reactor, the power ramp can be prevented. (Kawakami, Y.)

Radionuclide release from PWR fuels in a reference tuff repository groundwater

International Nuclear Information System (INIS)

Wilson, C.N.; Oversby, V.M.

1985-03-01

The Nevada Nuclear Waste Storage Investigations Project (NNWSI) is studying the suitability of the welded devitrified Topopah Spring tuff at Yucca Mountain, Nye County, Nevada, for potential use as a high-level nuclear waste repository. In support of the Waste Package task of NNWSI, tests have been conducted under ambient air environment to measure radionuclide release from two pressurized water reactor (PWR) spent fuels in water obtained from the J-13 well near the Yucca Mountain site. Four specimen types, representing a range of fuel physical conditions that may exist in a failed waste canister containing a limited amount of water were tested. The specimen types were: fuel rod sections split open to expose bare fuel particles; rod sections with water-tight end fittings with a 2.5-cm long by 150-μm wide slit through the cladding; rod sections with water-tight end fittings and two 200-μm-diameter holes through the cladding; and undefected rod segments with water-tight end fittings. Radionuclide release results from the first 223-day test runs on H.B. Robinson spent fuel specimens in J-13 water are reported and compared to results from a previous test series in which similar Turkey Point reactor spent fuel specimens were tested on deionized water. Selected initial results are also given for Turkey Point fuel specimens tested on J-13 water. Results suggest that the actinides Pu, Am, Cm and Np are released congruently with U as the UO 2 spent fuel matrix dissolves. Fractional release of 137 Cs and 99 Tc was greater than that measured for the actinides. Generally, lower radionuclide releases were measured for the H.B. Robinson fuel in J-13 water than for Turkey Point Fuel in deionized water. 8 references, 7 figures, 9 tables

Two codes used in analysis of rod ejection accident for Qinshan Nuclear Power Plant

International Nuclear Information System (INIS)

Zhu Xinguan

1987-12-01

Two codes were developed to analyse rod ejection accident for Qinshan Nuclear Power Plant. One was based on point model with temperature reactivity feedback. In this code, the worth of ejected rod was obtained under'adiabatic' approximation. In the other code, the Nodal Green's Function Method was used to solve space-time dependent neutron diffusion equation. Using these codes, the transient core-power have been calculated for two rod ejection cases at beginning of core-life in Qinshan Nuclear Power Plant

Application of a spatial modal kinetic model for determination of control rod worths

International Nuclear Information System (INIS)

Gomez, A.; Waldman, R.M.

1993-01-01

A high-precision rod drop method based on a modal kinetic model, with low dependence on detector location, is proposed to measure the reactivity worth of control rods. This value is obtained from data adjustment for the delayed evolution. It is necessary to maintain the experimental data fluctuation in a small value so that the error of the control rod worth should not be large. A model was developed in order to relate the fluctuation with some parameters which may be modified in the measuring process. The method was applied in the RA-6 reactor to measure control rod worth. For practical purpose it was found that the method can be applied to 15 dollars and it does not depend on relative detector and control rod locations, as the method based on the Point Reactor Model does. (author). 2 refs

Thermal behavior simulation of a nuclear fuel rod through an eletrically heated rod

International Nuclear Information System (INIS)

Lima, R. de C.F. de.

1984-01-01

In thermalhydraulic loops the nuclear industry often uses electrically heated rods to simulate power transients, which occur in nuclear fuel rods. The development and design of a electrically heated rod, by supplying the dimensions and materials which should be used in order to yeld the same temperature and heat flux at the surfaces of the nuclear rod and the electrically heated rod are presented. To a given nuclear transient this equality was obtained by fitting the linear power through the lumped parameters technique. (Author) [pt

Nuclear fuel rod loading apparatus

International Nuclear Information System (INIS)

King, H.B.; Macivergan, R.; Mckenzie, G.W.

1980-01-01

An apparatus incorporating a microprocessor control is provided for automatically loading nuclear fuel pellets into fuel rods commonly used in nuclear reactor cores. The apparatus comprises a split ''v'' trough for assembling segments of fuel pellets in rows and a shuttle to receive the fuel pellets from the split ''v'' trough when the two sides of the split ''v'' trough are opened. The pellets are weighed while in the shuttle, and the shuttle then moves the pellets into alignment with a fuel rod. A guide bushing is provided to assist the transfer of the pellets into the fuel rod. A rod carousel which holds a plurality of fuel rods presents the proper rod to the guide bushing at the appropriate stage in the loading sequence. The bushing advances to engage the fuel rod, and the shuttle advances to engage the guide bushing. The pellets are then loaded into the fuel rod by a motor operated push rod. The guide bushing includes a photocell utilized in conjunction with the push rod to measure the length of the row of fuel pellets inserted in the fuel rod

Control rod shutdown system

International Nuclear Information System (INIS)

Miyamoto, Yoshiyuki; Higashigawa, Yuichi.

1996-01-01

The present invention provides a control rod terminating system in a BWR type nuclear power plant, which stops an induction electric motor as rapidly as possible to terminate the control rods. Namely, the control rod stopping system controls reactor power by inserting/withdrawing control rods into a reactor by driving them by the induction electric motor. The system is provided with a control device for controlling the control rods and a control device for controlling the braking device. The control device outputs a braking operation signal for actuating the braking device during operation of the control rods to stop the operation of the control rods. Further, the braking device has at least two kinds of breaks, namely, a first and a second brakes. The two kinds of brakes are actuated by receiving the brake operation signals at different timings. The brake device is used also for keeping the control rods after the stopping. Even if a stopping torque of each of the breaks is small, different two kinds of brakes are operated at different timings thereby capable of obtaining a large stopping torque as a total. (I.S.)

Fuel rod leak detector

International Nuclear Information System (INIS)

Womack, R.E.

1978-01-01

A typical embodiment of the invention detects leaking fuel rods by means of a radiation detector that measures the concentration of xenon-133 ( 133 Xe) within each individual rod. A collimated detector that provides signals related to the energy of incident radiation is aligned with one of the ends of a fuel rod. A statistically significant sample of the gamma radiation (γ-rays) that characterize 133 Xe is accumulated through the detector. The data so accumulated indicates the presence of a concentration of 133 Xe appropriate to a sound fuel rod, or a significantly different concentration that reflects a leaking fuel rod

Fuel rods

International Nuclear Information System (INIS)

Hattori, Shinji; Kajiwara, Koichi.

1980-01-01

Purpose: To ensure the safety for the fuel rod failures by adapting plenum springs to function when small forces such as during transportation of fuel rods is exerted and not to function the resilient force when a relatively great force is exerted. Constitution: Between an upper end plug and a plenum spring in a fuel rod, is disposed an insertion member to the lower portion of which is mounted a pin. This pin is kept upright and causes the plenum spring to function resiliently to the pellets against the loads due to accelerations and mechanical vibrations exerted during transportation of the fuel rods. While on the other hand, if a compression force of a relatively high level is exerted to the plenum spring during reactor operation, the pin of the insertion member is buckled and the insertion member is inserted to the inside of the plenum spring, whereby the pellets are allowed to expand freely and the failures in the fuel elements can be prevented. (Moriyama, K.)

Recent energy studies and energy policies in Turkey

Energy Technology Data Exchange (ETDEWEB)

Gullu, D.; Caglar, A.; Akdeniz, F. [Karadeniz Technical University, Trabzon (Turkey). Faculty of Education

2001-07-01

Currently, considerable attention has been focused on the energy sources and energy studies in Turkey. Indigenous energy consumption accounts for 37% of total energy consumption. The Turkish government's investment needs in the energy sector for the period 2000-2010 will be around 55 billion US dollars. Of this, about 81% is total planning investments. Conventional financing of major infrastructure projects would only increase the amount of foreign credit, thus the Ministry of Energy and Natural Resources (MENR) has conceived other options for financing projects. One option is the so-called Build, Operate, and Transfer (BOT) model, where private investors build and operate private sector generation for certain number of years, at which point they transfer ownership to the state. In June 1996, MENR introduced the Build, Own, and Operate (BOO) financing model. A major dilemma now faced by Turkey is how to invest in new electric power capacity while at the same time adhering to foreign debt ceilings to under lending rules set by the International Monetary Fund. Turkey has to adopt new long-term energy strategies to reduce the share of fossil fuels in the primary energy consumption. Recently, the development of alternative energy sources has been a major focus of the research effort in Turkey.

3-Dimensional Methodology for the Control Rod Ejection Accident Analysis Using UNICORNTM

International Nuclear Information System (INIS)

Jang, Chan-su; Um, Kil-sup; Ahn, Dawk-hwan; Kim, Yo-han; Sung, Chang-kyung; Song, Jae-seung

2006-01-01

The control rod ejection accident has been analyzed with STRIKIN-II code using the point kinetics model coupled with conservative factors to address the three dimensional aspects. This may result in a severe transient with very high fuel enthalpy deposition. KNFC, under the support of KEPRI and KAERI, is developing 3-dimensional methodology for the rod ejection accident analysis using UNICORNTM (Unified Code of RETRAN, TORC and MASTER). For this purpose, 3-dimensional MASTER-TORC codes, which have been combined with the dynamic-link library by KAERI, are used in the transient analysis of the core and RETRAN code is used to estimate the enthalpy deposition in the hot rod

Luminescence behaviour of beryl (aquamarine variety) from Turkey

Energy Technology Data Exchange (ETDEWEB)

Kat Latin-Small-Letter-Dotless-I , M.I.; Tueremis, M.; Keskin, I.C.; Tastekin, B.; Kibar, R.; Cetin, A. [Celal Bayar University, Faculty of Arts and Sciences, Physics Department, 45140 Manisa (Turkey); Can, N., E-mail: cannurdogan@yahoo.com [Celal Bayar University, Faculty of Arts and Sciences, Physics Department, 45140 Manisa (Turkey)

2012-10-15

Natural blue-green beryl from Turkey has been investigated using scanning electron microscopy-energy-dispersive spectroscopy (SEM-EDS), X-ray diffraction (XRD) and Cathodoluminescence (CL). Beryl has the chemical formula Be{sub 3}Al{sub 2}Si{sub 6}O{sub 18} and is hexagonal with space group P6/mcc. Chemical analyses of the beryl sample utilised inductively coupled plasma-atomic emission spectroscopy (ICP-AES) for major oxides and trace elements. It shows that the beryl sample is rich in Cs (531 ppm) and contains low concentrations of transition-metal ions, in total 2.29 wt.% Fe, 269 ppm Mn, V<5 ppm and Cr 20 ppm. Ideas on the origin of the green colour of this mineral are presented. The CL spectrum of the bulk sample display intense broad band emission from {approx}360 to {approx}800 nm. - Highlights: Black-Right-Pointing-Pointer Natural blue-green beryl from Turkey were investigated by SEM-EDS, XRD, CL. Black-Right-Pointing-Pointer Luminescence behaviour of Natural blue-green beryl. Black-Right-Pointing-Pointer The samples exhibit an intense broad band emission from {approx}360 to {approx}800 nm.

Multiple fuel rod gripper

International Nuclear Information System (INIS)

Shields, E.P.

1987-01-01

An apparatus is described for gripping an array of rods comprising: (a) gripping members grippingly engageable with the rods, each of which has a hollow portion terminating in an open end for receiving the end of one of the rods; (b) a closing means for causing the hollow portion of each of the gripping members to apply substantially the same gripping force onto the end of its respective rod, including (i) a locking plate having a plurality of tapered holes registrable with the array of rods, wherein the exterior of each of the gripping members is tapered and nested within one of the tapered holes, (ii) a withdrawing means having a hydraulic plunger operatively connected to each of the gripping members for applying a substantially identical withdrawing force on each of the gripping members, whereby the hollow portion of each of the gripping members applies substantially the same gripping force on its respective rod, and (c) means for detecting whether each of the gripping members has grippingly engaged its respective rod

High-yield production of hydrophobins RodA and RodB from Aspergillus fumigatus in Pichia pastoris

DEFF Research Database (Denmark)

Pedersen, Mona Højgaard; Borodina, Irina; Moresco, Jacob Lange

2011-01-01

A as well as rRodB were able to convert a glass surface from hydrophilic to hydrophobic similar to native RodA, but only rRodB was able to decrease the hydrophobicity of a Teflon-like surface to the same extent as native RodA, while rRodA showed this ability to a lesser extent. Recombinant RodA and native...

A study on the thermal hydraulics in rod bundles

International Nuclear Information System (INIS)

Chung, Moon Ki; Yang, Sun Kyu

1989-03-01

In order to improve the thermal hydraulic characteristics of the nuclear reactor core, it is necessary to obtain better understanding of the coolant flow and the enthalpy distribution in complex rod bundle geometries. The purpose of this report is to obtain a comprehensive survey on the thermal hydraulic in rod bundles from both experimental and numerical point of view. From references on experimental study, measurement methods and results of the flow velocity and the pressure drop in the subchannels of rod bundles are expressed. The microscopic flow characteristics of the subchannels and spacer grid effect on the flow structure are described. Physical phenomena and measurement methods of the secondary flow are also described. From references on the numerical study, general numerical methods are expressed. Numerical studies on the laminar flow and turbulent flow such as 1-equation and 2-equation model are reviewed.(Author)

Data report for the nondestructive examination of Turkey Point spent fuel assemblies B02, B03, B17, B41, and B43

International Nuclear Information System (INIS)

Davis, R.B.

1980-04-01

The fuel assembly sip test on all rods from assembly B17 were of sound intergrity. Visual examination showed three general regions of rod surface appearance: a dark adherent crud layer at the bottom of the rod, black spalling crud layers in the middle, and a spotty gray loose powdery coating with dark crud or oxide underneath towards the top. Rod lengths varied from 152.395 inches to 152.707 inches. Maximum rod bow measurements for rods G9, I9, and G7 were 0.038 to 040 inch and 0.022 inch for rods H6 and J8. Results from profilometry scans showed the maximum ovality for the five rods was 0.0066 inch with average diameters ranging from 0.4187 to 0.4198 inch. Extensive ridging from pellet-clad interaction over the entire length was evident on all rods. Gamma scan results showed no cesium peaking and no pellet gaps greater than 0.025 inch. No unusual areas, other than ridging and possible fuel-cladding bonding, were seen in the eddy current results

Cone dystrophy with "supernormal" rod ERG: psychophysical testing shows comparable rod and cone temporal sensitivity losses with no gain in rod function.

Science.gov (United States)

Stockman, Andrew; Henning, G Bruce; Michaelides, Michel; Moore, Anthony T; Webster, Andrew R; Cammack, Jocelyn; Ripamonti, Caterina

2014-02-10

We report a psychophysical investigation of 5 observers with the retinal disorder "cone dystrophy with supernormal rod ERG," caused by mutations in the gene KCNV2 that encodes a voltage-gated potassium channel found in rod and cone photoreceptors. We compared losses for rod- and for cone-mediated vision to further investigate the disorder and to assess whether the supernormal ERG is associated with any visual benefit. L-cone, S-cone, and rod temporal acuity (critical flicker fusion frequency) were measured as a function of target irradiance; L-cone temporal contrast sensitivity was measured as a function of temporal frequency. Temporal acuity measures revealed that losses for vision mediated by rods, S-cones, and L-cones are roughly equivalent. Further, the gain in rod function implied by the supernormal ERG provides no apparent benefit to near-threshold rod-mediated visual performance. The L-cone temporal contrast sensitivity function in affected observers was similar in shape to the mean normal function but only after the mean function was compressed by halving the logarithmic sensitivities. The name of this disorder is potentially misleading because the comparable losses found across rod and cone vision suggest that the disorder is a generalized cone-rod dystrophy. Temporal acuity and temporal contrast sensitivity measures are broadly consistent with the defect in the voltage-gated potassium channel producing a nonlinear distortion of the photoreceptor response but after otherwise normal transduction processes.

Evaluation of control rod motion simulator research reactors

International Nuclear Information System (INIS)

Sanda

2010-01-01

Motion simulator has been carried out testing of the reactor control rod using a servomotor. Reactor control rod motion at any point should be in the right position, one of the motors that can move in a precise and correct the servo motor. To ensure that the servo motor to move in accordance with the desired program, then the servomotor function test for motor work to ensure the performance of the appliance. Tests carried out on meshes stress disorder, the load is stable within a certain period and travel time safety control rod up and down, travel time regulating control rods up and down and travel time compensation control rods up and down. In testing the breakdown voltage Vout nets at 24 V, 6.5 A with 12 Ω load deviation obtained V0 = V1 = 0.1% and 0.65% and for the stability of the load in a certain time deviation V = 0.7125%, next to the breakdown voltage Vout nets at 12V, 4.2 A with a 6 Ω load deviation obtained V0 = V1 = 0.275% and 1.158% for the stability of the load in a certain time deviation V = 1.463% and the net-voltage noise nets on Vout 24 V, 4.5 A with 12 Ω load deviation obtained V0 = V1 = 0.196% and 0.496% and for the stability of the load in a certain time deviation V = 0.3625%. While the travel time of a safety control rod up and down, up and down the regulator and compensation rise and fall showed a steady linear graph. The results show that the performance of the servo motor is very stable with the working area below the tolerance limit, it is 5% - 10%. (author)

Control rod drive for vertical movement

International Nuclear Information System (INIS)

Suskov, I.I.; Gorjunov, V.S.; Zajcev, B.I.; Derevjankin, N.E.; Petrov, V.A.; Istomin, S.D.; Kovalencik, D.I.; Archipov, E.A.; Serebrjakov, V.I.; Kacalin, V.S.

1982-01-01

The control of the rod repositioning gear unit and the control unit of the profile grab of the control rod drive for the alkali metal-cooled fast breeder reactor is achieved by an electromotor being arranged outside the hermetic drive casing. The guide tube is directly repositioned by the rod repositioning gear unit. Coupling control of the drive with the control rod is done in the lower operative position of the control rod and that because of the interaction of the tie rod arranged on the spring-mounted control rod with the induction transmitter for the lower position of the control rod. In the transfer position the rod is fixed within the guide tube. (orig.)

Safety rod driving device

International Nuclear Information System (INIS)

Murakami, Kiyonobu; Kurosaki, Akira.

1988-01-01

Purpose: To rapidly insert safety rods for a criticality experiment device into a reactor core container to stop the criticality reaction thereby prevent reactivity accidents. Constitution: A cylinder device having a safety rod as a cylinder rod attached with a piston at one end is constituted. The piston is elevated by pressurized air and attracted and fixed by an electromagnet which is a stationary device disposed at the upper portion of the cylinder. If the current supply to the electromagnet is disconnected, the safety rod constituting the cylinder rod is fallen together with the piston to the lower portion of the cylinder. Since the cylinder rod driving device has neither electrical motor nor driving screw as in the conventional device, necessary space can be reduced and the weight is decreased. In addition, since the inside of the nuclear reactor can easily be shielded completely from the external atmosphere, leakage of radioactive materials can be prevented. (Horiuchi, T.)

INDIAN POINT REACTOR REACTIVITY AND FLUX DISTRIBUTION MEASUREMENTS

Energy Technology Data Exchange (ETDEWEB)

Batch, M. L.; Fischer, F. E.

1963-11-15

The reactivity of the Indian Point core was measured near zero reactivity at various shim and control rod patterns. Flux distribution measurements were also made, and the results are expressed in terms of power peaking factors and normalized detector response during rod withdrawal. (D.L.C.)

All-dielectric rod antenna array for terahertz communications

Science.gov (United States)

Withayachumnankul, Withawat; Yamada, Ryoumei; Fujita, Masayuki; Nagatsuma, Tadao

2018-05-01

The terahertz band holds a potential for point-to-point short-range wireless communications at sub-terabit speed. To realize this potential, supporting antennas must have a wide bandwidth to sustain high data rate and must have high gain and low dissipation to compensate for the free space path loss that scales quadratically with frequency. Here we propose an all-dielectric rod antenna array with high radiation efficiency, high gain, and wide bandwidth. The proposed array is integral to a low-loss photonic crystal waveguide platform, and intrinsic silicon is the only constituent material for both the antenna and the feed to maintain the simplicity, compactness, and efficiency. Effective medium theory plays a key role in the antenna performance and integrability. An experimental validation with continuous-wave terahertz electronic systems confirms the minimum gain of 20 dBi across 315-390 GHz. A demonstration shows that a pair of such identical rod array antennas can handle bit-error-free transmission at the speed up to 10 Gbit/s. Further development of this antenna will build critical components for future terahertz communication systems.

Testing device for control rod drives

International Nuclear Information System (INIS)

Hayakawa, Toshifumi.

1992-01-01

A testing device for control rod drives comprises a logic measuring means for measuring an output signal from a control rod drive logic generation circuit, a control means for judging the operation state of a control rod and a man machine interface means for outputting the result of the judgement. A driving instruction outputted from the control rod operation device is always monitored by the control means, and if the operation instruction is stopped, a testing signal is outputted to the control rod control device to simulate a control rod operation. In this case, the output signal of the control rod drive logic generation circuit is held in a control rod drive memory means and intaken into a logic analysis means for measurement and an abnormality is judged by the control means. The stopping of the control rod drive instruction is monitored and the operation abnormality of the control rod is judged, to mitigate the burden of an operator. Further, the operation of the control rod drive logic generation circuit can be confirmed even during a nuclear plant operation by holding the control rod drive instruction thereby enabling to improve maintenance efficiency. (N.H.)

Post-test examination of the VVER-1000 fuel rod bundle CORA-W2

International Nuclear Information System (INIS)

Hofmann, P.; Noack, V.; Burbach, J.; Metzger, H.; Schanz, G.; Hagen, S.; Sepold, L.

1995-01-01

The upper half of the bundle is completely oxidized, the lower half has kept the fuel rods relatively intact. The post-test examination results show the strong impact of the B 4 C absorber rod and the stainless steel grid spacers on the 'low-temperature' bundle damage initiation and progression. The B 4 C absorber rod completely disappeared in the upper half of the bundle. The multicomponent melts relocated and formed coolant channel blockages on solidification with a maximum extent of about 30% in the lower part of the bundle. At temperatures above the melting point of the ZrNb1 cladding extensive fuel dissolution occured. (orig./HP)

Post-test examination of the VVER-1000 fuel rod bundle CORA-W2

Energy Technology Data Exchange (ETDEWEB)

Hofmann, P.; Noack, V.; Burbach, J.; Metzger, H.; Schanz, G.; Hagen, S.; Sepold, L.

1995-08-01

The upper half of the bundle is completely oxidized, the lower half has kept the fuel rods relatively intact. The post-test examination results show the strong impact of the B{sub 4}C absorber rod and the stainless steel grid spacers on the `low-temperature` bundle damage initiation and progression. The B{sub 4}C absorber rod completely disappeared in the upper half of the bundle. The multicomponent melts relocated and formed coolant channel blockages on solidification with a maximum extent of about 30% in the lower part of the bundle. At temperatures above the melting point of the ZrNb1 cladding extensive fuel dissolution occured. (orig./HP)

Failed fuel rod detector

Energy Technology Data Exchange (ETDEWEB)

Uchida, Katsuya; Matsuda, Yasuhiko

1984-05-02

The purpose of the project is to enable failed fuel rod detection simply with no requirement for dismantling the fuel assembly. A gamma-ray detection section is arranged so as to attend on the optional fuel rods in the fuel assembly. The fuel assembly is adapted such that a gamma-ray shielding plate is detachably inserted into optional gaps of the fuel rods or, alternatively, the fuel assembly can detachably be inserted to the gamma-ray shielding plate. In this way, amount of gaseous fission products accumulated in all of the plenum portions in the fuel rods as the object of the measurement can be determined without dismantling the fuel assembly. Accordingly, by comparing the amounts of the gaseous fission products, the failed fuel rod can be detected.

Development of subchannel void measurement sensor and multidimensional two-phase flow dynamics in rod bundle

International Nuclear Information System (INIS)

Arai, T.; Furuya, M.; Kanai, T.; Shirakawa, K.

2011-01-01

An accurate subchannel database is crucial for modeling the multidimensional two-phase flow in a rod bundle and for validating subchannel analysis codes. Based on available reference, it can be said that a point-measurement sensor for acquiring void fractions and bubble velocity distributions do not infer interactions of the subchannel flow dynamics, such as a cross flow and flow distribution, etc. In order to acquire multidimensional two-phase flow in a 10×10 rod bundle with an o.d. of 10 mm and 3110 mm length, a new sensor consisting of 11-wire by 11-wire and 10-rod by 10-rod electrodes was developed. Electric potential in the proximity region between two wires creates a void fraction in the center subchannel region, like a so-called wire mesh sensor. A unique aspect of the devised sensor is that the void fraction near the rod surface can be estimated from the electric potential in the proximity region between one wire and one rod. The additional 400 points of void fraction and phasic velocity in 10×10 bundle can therefore be acquired. The devised sensor exhibits the quasi three-dimensional flow structures, i.e. void fraction, phasic velocity and bubble chord length distributions. These quasi three-dimensional structures exhibit the complexity of two-phase flow dynamics, such as coalescence and the breakup of bubbles in transient phasic velocity distributions. (author)

RodPilotR - The Innovative and Cost-Effective Digital Control Rod Drive Control System for PWRs

International Nuclear Information System (INIS)

Baron, Clemens

2008-01-01

With RodPilot, AREVA NP offers an innovative and cost-effective system for controlling control rods in Pressurized Water Reactors. RodPilot controls the three operating coils of the control rod drive mechanism (lift, moveable gripper and stationary gripper coil). The rods are inserted into or withdrawn from the core as required by the Reactor Control System. The system combines modern components, state-of-the-art logic and a proven electronic control rod drive control principle to provide enhanced reliability and lower maintenance costs. (author)

Integrated control rod monitoring device

International Nuclear Information System (INIS)

Saito, Katsuhiro

1997-01-01

The present invention provides a device in which an entire control rod driving time measuring device and a control rod position support device in a reactor building and a central control chamber are integrated systematically to save hardwares such as a signal input/output device and signal cables between boards. Namely, (1) functions of the entire control rod driving time measuring device for monitoring control rods which control the reactor power and a control rod position indication device are integrated into one identical system. Then, the entire devices can be made compact by the integration of the functions. (2) The functions of the entire control rod driving time measuring device and the control rod position indication device are integrated in a central operation board and a board in the site. Then, the place for the installation of them can be used in common in any of the cases. (3) The functions of the entire control rod driving time measuring device and the control rod position indication device are integrated to one identical system to save hardware to be used. Then, signal input/output devices and drift branching panel boards in the site and the central operation board can be saved, and cables for connecting both of the boards is no more necessary. (I.S.)

Rod drive and latching mechanism

International Nuclear Information System (INIS)

Veronesi, L.; Sherwood, D.G.

1982-01-01

Hydraulic drive and latching mechanisms for driving reactivity control mechanisms in nuclear reactors are described. Preferably, the pressurized reactor coolant is utilized to raise the drive rod into contact with and to pivot the latching mechanism so as to allow the drive rod to pass the latching mechanism. The pressure in the housing may then be equalized which allows the drive rod to move downwardly into contact with the latching mechanism but to hold the shaft in a raised position with respect to the reactor core. Once again, the reactor coolant pressure may be utilized to raise the drive rod and thus pivot the latching mechanism so that the drive rod passes above the latching mechanism. Again, the mechanism pressure can be equalized which allows the drive rod to fall and pass by the latching mechanism so that the drive rod approaches the reactor core. (author)

Analysis of environmental impact assessment (EIA) system in Turkey.

Science.gov (United States)

Coşkun, Aynur Aydın; Turker, Ozhan

2011-04-01

The Environmental Impact Assessment (EIA) System, which embodies the "prevention principle" of the environmental law, is an important tool for environmental protection. This tool has a private importance for Turkey since it is a developing country, and it entered the Turkish law in 1983 with the Environmental Law. Besides, the EIA Regulation, which shows the application principles, became effective in 1993. Because Turkey is a candidate for European Union (EU), the EIA Regulation has been changed due to the EU compliance procedure, and its latest version became valid in 2008. This study aims to emphasize The EIA system in Turkey to supervise the efficiency of this procedure and point the success level. In the introduction part, general EIA concept, its importance, and some notations are mentioned. Following that, the legislation, which builds the EIA system, has been analyzed starting from the 1982 Turkish Constitution. Then, the legislation rules are explained due to the basic steps of the EIA procedure. In order to shed light upon the application, the EIA final decisions given until today, the results, and their distributions to the industries are assessed. In the final part of the study, a SWOT analysis is made to mention the weaknesses, strengths, opportunities, and threats of the EIA system in Turkey.

Control rods

International Nuclear Information System (INIS)

Koga, Isao; Masuoka, Ryuzo.

1979-01-01

Purpose: To prevent fuel element failures during power conditioning by removing liquid absorbents in poison tubes of control rods in a fast power up step and extracting control rods to slightly increase power in a medium power up step. Constitution: A plurality of poison tubes are disposed in a coaxial or plate-like arrangement and divided into a region capable of compensating the reactivity from the initial state at low temperature to 40% power operation and a region capable of compensating the reactivity in the power up above 40% power operation. Soluble poisons are used as absorbers in the poison tubes corresponding to above 40% power operation and they are adapted to be removed independently from the driving of control rods. The poison tubes filled with the soluble absorbers are responsible for the changes in the reactivity from the initial state at low temperature to the medium power region and the reactivity control is conducted by the elimination of liquid absorbers from the poison tubes. In the succeeding slight power up region above the medium power, power up is proceeding by extracting the control rods having remaining poison tubes filled with solid or liquid absorbers. (Seki, T.)

Simulation of nuclear fuel rods by using process computer-controlled power for indirect electrically heated rods

International Nuclear Information System (INIS)

Malang, S.

1975-11-01

An investigation was carried out to determine how the simulation of nuclear fuel rods with indirect electrically heated rods could be improved by use of a computer to control the electrical power during a loss-of-coolant accident (LOCA). To aid in the experiment, a new version of the HETRAP code was developed which simulates a LOCA with heater rod power controlled by a computer that adjusts rod power during a blowdown to minimize the difference in heat flux of the fuel and heater rods. Results show that without computer control of heater rod power, only the part of a blowdown up to the time when the heat transfer mode changes from nucleate boiling to transition or film boiling can be simulated well and then only for short times. With computer control, the surface heat flux and temperature of an electrically heated rod can be made nearly identical to that of a reactor fuel rod with the same cooling conditions during much of the LOCA. A small process control computer can be used to achieve close simulation of a nuclear fuel rod with an indirect electrically heated rod

Technical evaluation report on the Third 10-year Interval Inservice Inspection Program Plan: Florida Power and Light Company, Turkey Point Nuclear Power Plant, Units 3 and 4 (Docket Numbers 50-250 and 50-251)

International Nuclear Information System (INIS)

Brown, B.W.; Feige, E.J.; Galbraith, S.G.; Porter, A.M.

1995-02-01

This report presents the results of the evaluation of the Turkey Point Nuclear Power Plant, Units 3 and 4, Third 10-Year Interval Inservice Inspection Program Plan, Revision 0, submitted September 9, 1993, including the requests for relief from the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section XI, requirements that the licensee has determined to be impractical. The Turkey Point Nuclear Power Plant, Units 3 and 4, Third 10-Year Interval Inservice Inspection Program Plan is evaluated in Section 2 of this report. The inservice inspection (ISI) program plan is evaluated for (a) compliance with the appropriate edition/addenda of Section XI, (b) acceptability of the examination sample, (c) correctness of the application of system or component examination exclusion criteria, and (d) compliance with ISI-related commitments identified during previous Nuclear Regulatory Commission (NRC) reviews. The requests for relief are evaluated in Section 3 of this report

Motor fuel prices in Turkey

International Nuclear Information System (INIS)

Erdogdu, Erkan

2014-01-01

The world's most expensive motor fuel (gasoline, diesel and LPG) is sold most likely in the Republic of Turkey. This paper investigates the key issues related to the motor fuel prices in Turkey. First of all, the paper analyses the main reason behind high prices, namely motor fuel taxes in Turkey. Then, it estimates the elasticity of motor fuel demand in Turkey using an econometric analysis. The findings indicate that motor fuel demand in Turkey is quite inelastic and, therefore, not responsive to price increases caused by an increase in either pre-tax prices or taxes. Therefore, fuel market in Turkey is open to opportunistic behavior by firms (through excessive profits) and the government (through excessive taxes). Besides, the paper focuses on the impact of high motor fuel prices on road transport associated activities, including the pattern of passenger transportation, motorization rate, fuel use, total kilometers traveled and CO 2 emissions from road transportation. The impact of motor fuel prices on income distribution in Turkey and Turkish public opinion about high motor fuel prices are also among the subjects investigated in the course of the study. - Highlights: • The key issues (e.g. taxes) related to motor fuel prices in Turkey are explored. • Their impact on transport activities and income distribution is also investigated. • An econometric analysis is performed to estimate motor fuel demand in Turkey. • Motor fuel demand in Turkey is found to be quite inelastic. • Turkish fuel market is open to opportunistic behavior by firms and the government

Development of multidimensional two-phase flow measurement sensor in rod bundle

International Nuclear Information System (INIS)

Arai, Takahiro; Furuya, Masahiro; Shirakawa, Kenetsu; Kanai, Taizo

2011-01-01

In order to acquire multidimensional two-phase flow in 10x10 bundle, SubChannel Void Sensor (SCVC) consisting of 11-wire by 11-wire and 10-rod by 10-rod electrodes is developed. A conductance value in a proximity region of one wire and another gives void fraction in the center of subchannel region. A phasic velocity can be estimated by using two layers of wire meshes, like as so-called wire mesh sensor. 121 points (=11x11) of void fraction as well as those of phasic velocity are acquired. It is peculiarity of the devised sensor that void fraction near rod surface can be estimated by a conductance value in a proximity region of one wire and one rod. 400 additional points of void fraction in 10x10 bundle can be, therefore, acquired. The time resolution of measurement is up to 1250 frames (cross sections) per second. We capability in a 10x10 bundle with o.d. 10 mm and 3110 mm long is demonstrated. The devised sensor is installed in 8 height levels to acquire the two-phase flow dynamics along axial direction. A pair of sensor layers is mounted in each level and is placed by 30 mm apart with each other to estimate a phasic velocity distribution on the basis of cross-correlation function of the two layers. Air bubbles are injected through sintered metal nozzles from the bottom end of 10x10 rods. Air flow rate distribution can vary with a controlled valves connected to each nozzle. The devised sensor exhibited the quasi three-dimensional flow structures, i.e. void fraction, phasic velocity and bubble chord length distributions. These quasi three-dimensional structures explorer complexity of two-phase flow dynamics such as coalescence and breakup of bubbles in the transient phasic velocity distributions. (author)

Digital control rod blocking monitor

International Nuclear Information System (INIS)

Funayama, Yoshio.

1996-01-01

The present invention system is used for monitoring of a power region of a reactor, and used for monitoring of simultaneous withdrawal of a plurality of control rods without increasing the size or complicating the system. Namely, the system processes signals from a neutron flux detectors at the periphery of control rods controlled for withdrawal. As a result of the processing, the digital monitoring system generates an alarm when the reactor power at the periphery of the control rods fluctuates exceeding an allowable range. In the system, a control rod information forming means prepares frame data comprising front data, positions of the control rods to be withdrawn, frame numbers and completion data. A serial data transmitting means transmits the frame data successively as repeating frame data rows. A control rod information receiving means takes up the frame data of each of control rods to be withdrawn from the transmitted frame data rows. Since the system of the present invention can monitor the withdrawal of a plurality of control rods simultaneously without increasing the size or complicating the system, cost can be saved and the maintenance can be improved. (I.S.)

The BWR Hybrid 4 control rod

International Nuclear Information System (INIS)

Gross, H.; Fuchs, H.P.; Lippert, H.J.; Dambietz, W.

1988-01-01

The service life of BWR control rods designed in the past has been unsatisfactory. The main reason was irradiation assisted stress corrosion cracking of B 4 C rods caused by external swelling of the B 4 C powder. By this reason KWU developed an improved BWR control rod (Hybrid 4 control rod) with extended service life and increased control rod worth. It also allows the procedure for replacing and rearranging fuel assemblies to be considerably simplified. A complete set of Hydbrid 4 control rods is expected to last throughout the service life of a plant (assumption: ca. 40 years) if an appropriate control rod reshuffling management program is used. (orig.)

Burnable poison rod

International Nuclear Information System (INIS)

Natsume, Tomohiro.

1988-01-01

Purpose: To decrease the effect of water elimination and the effect of burn-up residue boron, thereby reduce the effect of burnable poison rods as the neutron poisons at the final stage of reactor core lifetime. Constitution: In a burnable poison rod according to the present invention, a hollow burnable poison material is filled in an external fuel can, an inner fuel can mounted with a carbon rod is inserted to the hollow portion of the burnable poison material and helium gases are charged in the outer fuel can. In such a burnable poison rod, the reactivity worths after the burning are reduced to one-half as compared with the conventional case. Accordingly, since the effect of the burnable poison as the neutron poisons is reduced at the final stage of the reactor core of lifetime, the excess reactivity of the reactor core is increased. (Horiuchi, T.)

The Graphical Cadastre Problem in Turkey: The Case of Trabzon Province

Directory of Open Access Journals (Sweden)

Yakup Emre Çoruhlu

2008-09-01

Full Text Available Cadastral projects in Turkey have been accelerated in recent years by the involvement of the private sector. These projects aim at completing the country’s cadastre, along with producing bases in standards that could be a foundation for Land Registry and Cadastre Information System (LRCIS. It is possible to produce cadastral data with today’s technological means. In this context, three dimensional cadastre data can be properly produced, especially in digital cadastre projects with the required point accuracy. Nevertheless this is not enough for LRCIS. The cadastre bases that have been produced so far by different methods with different scales and bases, with or without coordinates, should also be converted into digital form based on National Basic GPS Network of Turkey (NBGN in required point-location accuracy. As the result of evaluation of graphical cadastre bases produced without coordinates, actual land measurements, and information obtained from sheets and field book data together, it was found out that there are significant base problems in the graphical maps. These bases, comprising 20% of Turkey’s cadastre constitutes the most important bottleneck of completing the country’s cadastre. In the scope of this paper, the possibilities of converting the field book measurement values of graphic cadastre bases into digital forms in national coordinate system by comparing them with actual land measurements are investigated, along with Turkey’s Cadastre and its problems.

Biomechanics of lumbar cortical screw-rod fixation versus pedicle screw-rod fixation with and without interbody support.

Science.gov (United States)

Perez-Orribo, Luis; Kalb, Samuel; Reyes, Phillip M; Chang, Steve W; Crawford, Neil R

2013-04-15

Seven different combinations of posterior screw fixation, with or without interbody support, were compared in vitro using nondestructive flexibility tests. To study the biomechanical behavior of a new cortical screw (CS) fixation construct relative to the traditional pedicle screw (PS) construct. The CS is an alternative to the PS for posterior fixation of the lumbar spine. The CS trajectory is more sagittally and cranially oriented than the PS, being anchored in the pars interarticularis. Like PS fixation, CS fixation uses interconnecting rods fastened with top-locking connectors. Stability after bilateral CS fixation was compared with stability after bilateral PS fixation in the setting of intact disc and with direct lateral interbody fixation (DLIF) or transforaminal lateral interbody fixation (TLIF) support. Standard nondestructive flexibility tests were performed in cadaveric lumbar specimens, allowing non-paired comparisons of specific conditions from 28 specimens (4 groups of 7) within a larger experiment of multiple hardware configurations. Condition tested and group from which results originated were as follows: (1) intact (all groups); (2) with L3-L4 bilateral PS-rods (group 1); (3) with bilateral CS-rods (group 2); (4) with DLIF (group 3); (5) with DLIF + CS-rods (group 4); (6) with DLIF + PS-rods (group 3); (7) with TLIF + CS-rods (group 2), and (8) with TLIF + PS-rods (group 2). To assess spinal stability, the mean range of motion, lax zone, and stiff zone at L3-L4 were compared during flexion-extension, lateral bending, and axial rotation. With intact disc, stability was equivalent after PS-rod and CS-rod fixation, except that PS-rod fixation was stiffer during axial rotation. With DLIF support, there was no significant difference in stability between PS-rod and CS-rod fixation. With TLIF support, PS-rod fixation was stiffer than CS-rod fixation during lateral bending. Bilateral CS-rod fixation provided about the same stability in cadaveric specimens

Managing dental caries in children in Turkey--a discussion paper.

Science.gov (United States)

Topaloglu-Ak, Asli; Eden, Ece; Frencken, Jo E

2009-11-25

This paper describes the oral healthcare system and disease situation amongst children in Turkey. Considering the high prevalence and severity of dental caries, a proposal for improvement of oral health in this population group is formulated. A virtual absence of palliative, preventive and restorative care characterises juvenile oral healthcare in Turkey. Consequently, carious cavities remain untreated, which may lead to pain, discomfort and functional limitation and, further, may impact negatively upon general health and cognitive development. As a first step to controlling dental caries, a national health programme including promotional, preventive and minimal intervention approaches for managing dental caries is proposed. The pros and cons of community-oriented caries-preventive measures are discussed. Daily tooth brushing with fluoridated toothpaste at home, in mother- and child-care centres, kindergartens, and schools is highlighted. The dental profession, government, university officials and other stakeholders need to meet and determine how best the oral health of children in Turkey can be improved. The present proposed plan is considered a starting point.

Freely suspended rod fall dampener, especially for control rod of liquid-cooled nuclear reactor

International Nuclear Information System (INIS)

Becvar, J.; Saroch, V.

1977-01-01

A shock absorber is described whose advantage is that the space required for the movement of the shock absorber in the operating travel of the system suspension rod-control rod bundle may be reduced. The design allows the automatic disconnection of the system and the removal of the suspension rod from the reactor without dismantling. The braking force reaction is transmitted to the structure above the core. The system fall energy is absorbed on the side of the suspension rod which has a bigger mass. (J.B.)

RodPilot{sup R} - The Innovative and Cost-Effective Digital Control Rod Drive Control System for PWRs

Energy Technology Data Exchange (ETDEWEB)

Baron, Clemens [AREVA NP GmbH, NLEE-G, Postfach 1199, 91001 Erlangen (Germany)

2008-07-01

With RodPilot, AREVA NP offers an innovative and cost-effective system for controlling control rods in Pressurized Water Reactors. RodPilot controls the three operating coils of the control rod drive mechanism (lift, moveable gripper and stationary gripper coil). The rods are inserted into or withdrawn from the core as required by the Reactor Control System. The system combines modern components, state-of-the-art logic and a proven electronic control rod drive control principle to provide enhanced reliability and lower maintenance costs. (author)

Post-harvest Salmonella spp. prevalence in turkey carcasses in processing plant in the northeast part of Poland.

Science.gov (United States)

Zdrodowska, B; Liedtke, K; Radkowski, M

2014-01-01

Turkeys carcasses at selected point after slaughter on dressing line in poultry were sampled and analyzed for Salmonella. These slaughter turkeys came from the northeast part of Poland. The examinations were carried out in each month of 2009. Three hundred turkeys were selected at random from a commercial slaughter line, immediately after completing the cooling process. The percentage of these 300 turkeys from which Salmonella spp. were isolated was relatively high (8.3%; Salmonella positive results were observed in 25 cases). The lowest Salmonella spp. rate (1.3 %) for slaughter birds was found in the fourth quarter, and the highest contamination rate at 18.6% was found, in the third quarter. The serological types of Salmonella spp. isolated from the whole turkey carcasses were S. Saintpaul, S. Senftenberg, S. Anatum, S. Heidelberg, S. Hadar, S. Typhimurium and S. Infantis.

3-Dimensional Methodology for the Control Rod Ejection Accident Analysis Using UNICORN{sup TM}

Energy Technology Data Exchange (ETDEWEB)

Jang, Chan-su; Um, Kil-sup; Ahn, Dawk-hwan [Korea Nuclear Fuel Company, Taejon (Korea, Republic of); Kim, Yo-han; Sung, Chang-kyung [KEPRI, Taejon (Korea, Republic of); Song, Jae-seung [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

2006-07-01

The control rod ejection accident has been analyzed with STRIKIN-II code using the point kinetics model coupled with conservative factors to address the three dimensional aspects. This may result in a severe transient with very high fuel enthalpy deposition. KNFC, under the support of KEPRI and KAERI, is developing 3-dimensional methodology for the rod ejection accident analysis using UNICORNTM (Unified Code of RETRAN, TORC and MASTER). For this purpose, 3-dimensional MASTER-TORC codes, which have been combined with the dynamic-link library by KAERI, are used in the transient analysis of the core and RETRAN code is used to estimate the enthalpy deposition in the hot rod.

ANALYSIS OF WAGE INEQUALITY IN TURKEY

OpenAIRE

Acun, Serdar

2018-01-01

Discussion of the notion of wages has consistently taken place in economicliterature. The way in which wages come to exist and are defined, and what theequilibrium point is have been the center of this discussion. The significant share of wages in total income hasraised its importance further. According to Turkey income and livingconditions data for 2015, wages and salaries held the proportion with 52.5 % oftotal income. As a consequence of that, the effect of wage inequality on incomeinequal...

Numerical study on the rotation of an elastic rod in a viscous fluid using an immersed boundary method

International Nuclear Information System (INIS)

Maniyeri, Ranjith; Kang, Sang Mo

2012-01-01

We present a three dimensional computational model based on an immersed boundary (IB) method to study the hydrodynamic features of a solid flexible cylindrical rod in a viscous fluid driven at one side by a tiny motor. The elastic rod is modelled by a number of circular cross-sections with twelve IB points on each cross-section. Three types of elastic links are created from each IB point to obtain an elastic network model of the rod and the first cross-section is modelled as the motor part. The elastic forces are computed based on an elastic energy approach and the motor forces are obtained from the applied angular frequency of rotation of the motor. The Stokes equations governing the fluid are solved on a staggered Cartesian grid system using the fractional-step based finite-volume method. Numerical simulations are performed to demonstrate the three dynamical stages of rod motion- twirling, whirling and overwhirling for different rotational frequency of the motor. It is revealed that for low rotational frequencies, the rod undergoes stable rigid body motion known as twirling. For high rotational frequencies of the motor, it is observed that the rod initially undergoes whirling motion and attains an unstable helical shape. Further, it is noticed that a discontinuous shape transition occurs for the rod and it folds back on itself. This unstable motion is referred to as overwhirling. It is also found that there exists a critical value of angular frequency of rotation of the motor below which the rod is subjected to twirling motion and above which it undergoes overwhirling motion

Gifted and Talented Education in Turkey: Critics and Prospects

Directory of Open Access Journals (Sweden)

Uğur Sak

2015-12-01

Full Text Available This article is a review and critics of gifted education in Turkey. Gifted education in Turkey has undergone dramatic changes in recent years. Innovations and regulations in the education of gifted and talented students have emerged and been formed as a result of a global agenda of the country. New steps such as the establishment of science high schools have been taken at specific critical point in history. With the beginning of the 21st century, the education of gifted students has gained momentum with the national strategic plan on gifted education and establishment of gifted education departments in universities. In the last fifteen years, the number of special programs and scientific publications has multiplied. Even though gifted education in Turkey has progressed notably over years, certain problems still remain unsolved, such as inconsistencies in definitions and contradictions between definitions and practices, inefficiency in nationwide identification, inadequate number of program types, recruitment of untrained teachers and lack of expertise in program development, and opposition against gifted education.

Control-rod driving mechanism

International Nuclear Information System (INIS)

Jodoi, Takashi.

1976-01-01

Purpose: To prevent falling of control rods due to malfunction. Constitution: The device of the present invention has a scram function in particular, and uses principally a fluid pressure as a scram accelerating means. The control rod is held by upper and lower holding devices, which are connected by a connecting mechanism. This connecting mechanism is designed to be detachable only at the lower limit of driving stroke of the control rod so that there occurs no erroneous scram resulting from careless disconnection of the connecting mechanism. Further, scramming operation due to own weight of the scram operating portion such as control rod driving shaft may be effected to increase freedom. (Kamimura, M.)

Preliminary design report for the prototypical fuel rod consolidation system

International Nuclear Information System (INIS)

Rosa, J.M.

1986-01-01

This report documents NUTECH's preliminary design of a dry, spent fuel rod consolidation system. This preliminary design is the result of Phase I of a planned four phase project. The present report on this project provides a considerable amount of detail for a preliminary design effort. The design and all of its details are described in this Preliminary Design Report (PDR). The NUTECH dry rod consolidation system described herein is remotely operated. It provides for automatic operation, but with operator hold points between key steps in the process. The operator has the ability to switch to a manual operation mode at any point in the process. The system is directed by the operator using an executive computer which controls and coordinates the operation of the in-cell equipment. The operator monitors the process using an in-cell closed circuit television (CCTV) system with audio output and equipment status displays on the computer monitor. The in-cell mechanical equipment consists of the following: (1) two overhead cranes with manipulators; (2) a multi-degree of freedom fuel handling table and its clamping equipment; (3) a fuel assembly end fitting removal station and its tools; (4) a consolidator (which pulls rods, assembles the consolidated bundle and loads the canister); (5) a canister end cap welder and weld inspection system; (6) decontamination systems; and (7) the CCTV and microphone systems

Simulation error propagation for a dynamic rod worth measurement technique

International Nuclear Information System (INIS)

Kastanya, D.F.; Turinsky, P.J.

1996-01-01

KRSKO nuclear station, subsequently adapted by Westinghouse, introduced the dynamic rod worth measurement (DRWM) technique for measuring pressurized water reactor rod worths. This technique has the potential for reduced test time and primary loop waste water versus alternatives. The measurement is performed starting from a slightly supercritical state with all rods out (ARO), driving a bank in at the maximum stepping rate, and recording the ex-core detectors responses and bank position as a function of time. The static bank worth is obtained by (1) using the ex-core detectors' responses to obtain the core average flux (2) using the core average flux in the inverse point-kinetics equations to obtain the dynamic bank worth (3) converting the dynamic bank worth to the static bank worth. In this data interpretation process, various calculated quantities obtained from a core simulator are utilized. This paper presents an analysis of the sensitivity to the impact of core simulator errors on the deduced static bank worth

REACTOR CONTROL ROD OPERATING SYSTEM

Science.gov (United States)

Miller, G.

1961-12-12

A nuclear reactor control rod mechanism is designed which mechanically moves the control rods into and out of the core under normal conditions but rapidly forces the control rods into the core by catapultic action in the event of an emergency. (AEC)

A probabilistic design method for LMFBR fuel rods

International Nuclear Information System (INIS)

Peck, S.O.; Lovejoy, W.S.

1977-01-01

Fuel rod performance analyses for design purposes are dependent upon material properties, dimensions, and loads that are statistical in nature. Conventional design practice accounts for the uncertainties in relevant parameters by designing to a 'safety factor', set so as to assure safe operation. Arbitrary assignment of these safety factors, based upon a number of 'worst case' assumptions, may result in costly over-design. Probabilistic design methods provide a systematic way to reflect the uncertainties in design parameters. PECS-III is a computer code which employs Monte Carlo techniques to generate the probability density and distribution functions for time-to-failure and cumulative damage for sealed plenum LMFBR fuel rods on a single rod or whole core basis. In Monte Carlo analyses, a deterministic model (that maps single-valued inputs into single-valued outputs) is coupled to a statistical 'driver'. Uncertainties in the input are reflected by assigning probability densities to the input parameters. Dependent input variables are considered multivariate normal. Independent input variables may be arbitrarily distributed. Sample values are drawn from these input densities, and a complete analysis is done by the deterministic model to generate a sample point in the output distribution. This process is repeated many times, and the number of times each output value occurs is accumulated. The probability that some measure of rod performance will fall within given limits is estimated by the relative frequency with which the Monte Carlo samples fall within tho

Does Government Support for Private Innovation Matter? Firm-Level Evidence from Turkey and Poland

OpenAIRE

Wojciech Grabowski; Teoman Pamukcu; Krzysztof Szczygielski; Sinan Tandogan

2013-01-01

The aim of the project is to analyze government support for innovation in a comparative perspective by first examining the main existing instruments of financial support for innovation in Turkey and Poland, and secondly to assess their effectiveness by applying recent econometric techniques to firm-level data for both countries obtained from the Community Innovation Survey (CIS). Comparing Turkey to Poland is both meaningful and promising from a policy-analysis point of view. Both countries a...

Towards Viscoplastic Constitutive Models for Cosserat Rods

OpenAIRE

Dörlich Vanessa; Linn Joachim; Scheffer Tobias; Diebels Stefan

2016-01-01

Flexible, slender structures like cables, hoses or wires can be described by the geometrically exact Cosserat rod theory. Due to their complex multilayer structure, consisting of various materials, viscoplastic behavior has to be expected for cables under load. Classical experiments like uniaxial tension, torsion or three-point bending already show that the behavior of e.g. electric cables is viscoplastic. A suitable constitutive law for the observed load case is crucial for a realistic simul...

Energy in Turkey

International Nuclear Information System (INIS)

Bumin, S.

2005-01-01

Because of its limited energy resources, Turkey is heavily dependent on imported oil and gas. 73 percent of the world's proven oil reserves and 72 percent of the world's proven gas reserves are located in the surrounding regions of Turkey: Middle East, Caspian Region and Russia. This makes Turkey a crucial bridge between energy rich regions and Europe. There are major oil and gas pipelines going through Turkey and additional pipelines are being constructed or are being planned. There is some production of lignite which is used in power plants and industry. Turkey's natural energy resources are quite diversified; with quite abundant coal reserves. Energy forecasts show that primary energy demand would be 117 million TOE in 2005 and 156 million TOE in 2010. Oil has the biggest share (39 percent) in total primary energy consumption, while natural gas has a share of 21 percent and increasing due to the recent diversification efforts of energy resources. Turkey has about 1percent of the total world hydroelectric potential and a considerable potential for electricity generation from wind. As of early 2004, Turkey had electric power generating capacity of around 32,000 megawatts (MW), and was building 13,000 MW more. Since adoption of Electricity Market Law in February 2001, there were significant changes towards liberalisation of power generation market and distribution in the country. Privatization of generation assets is envisaged to start in 2006. The Electricity Market Law set the stage for new supporting laws and regulations as well as new organization of the market: the Energy Market Regulation Agency (EMRA), that oversees the power, natural gas markets, oil markets and liquefied petroleum gases market, including setting tariffs, issuing licenses, and assuring competition; the Energy Market Regulatory Board, which runs the EMRA; the Energy Market Licensing Regulation and the Electricity Market Tariffs Regulation; 4-phase approach towards electric energy market

Control rod velocity limiter

International Nuclear Information System (INIS)

Cearley, J.E.; Carruth, J.C.; Dixon, R.C.; Spencer, S.S.; Zuloaga, J.A. Jr.

1986-01-01

This patent describes a velocity control arrangement for a reciprocable, vertically oriented control rod for use in a nuclear reactor in a fluid medium, the control rod including a drive hub secured to and extending from one end therefrom. The control device comprises: a toroidally shaped control member spaced from and coaxially positioned around the hub and secured thereto by a plurality of spaced radial webs thereby providing an annular passage for fluid intermediate the hub and the toroidal member spaced therefrom in coaxial position. The side of the control member toward the control rod has a smooth generally conical surface. The side of the control member away from the control rod is formed with a concave surface constituting a single annular groove. The device also comprises inner and outer annular vanes radially spaced from one another and spaced from the side of the control member away from the control rod and positioned coaxially around and spaced from the hub and secured thereto by spaced radial webs thereby providing an annular passage for fluid intermediate the hub and the vanes. The vanes are angled toward the control member, the outer edge of the inner vane being closer to the control member and the inner edge of the outer vane being closer to the control member. When the control rod moves in the fluid in the direction toward the drive hub the vanes direct a flow of fluid turbulence which provides greater resistance to movement of the control rod in the direction toward the drive hub than in the other direction

Control rod position control device

International Nuclear Information System (INIS)

Ubukata, Shinji.

1997-01-01

The present invention provides a control rod position control device which stores data such as of position signals and driving control rod instruction before and after occurrence of abnormality in control for the control rod position for controlling reactor power and utilized the data effectively for investigating the cause of abnormality. Namely, a plurality of individual control devices have an operation mismatching detection circuit for outputting signals when difference is caused between a driving instruction given to the control rod position control device and the control rod driving means and signals from a detection means for detecting an actual moving amount. A general control device collectively controls the individual control devices. In addition, there is also disposed a position storing circuit for storing position signals at least before and after the occurrence of the control rod operation mismatching. With such procedures, the cause of the abnormality can be determined based on the position signals before and after the occurrence of control rod mismatching operation stored in the position storing circuit. Accordingly, the abnormality cause can be determined to conduct restoration in an early stage. (I.S.)

Control rod selecting and driving device

International Nuclear Information System (INIS)

Isobe, Hideo.

1981-01-01

Purpose: To simultaneously drive a predetermined number of control rods in a predetermined mode by the control of addresses for predetermined number of control rods and read or write of driving codified data to and from the memory by way of a memory controller. Constitution: The system comprises a control rod information selection device for selecting predetermined control rods from a plurality of control rods disposed in a reactor and outputting information for driving them in a predetermined mode, a control rod information output device for codifying the information outputted from the above device and outputting the addresses to the predetermined control rods and driving mode coded data, and a driving device for driving said predetermined control rods in a predetermined mode in accordance with the codified data outputted from the above device, said control rod infromation output device comprising a memory device capable of storing a predetermined number of the codified data and a memory control device for storing the predetermined number of data into the above memory device at a predetermined timing while successively outputting the thus stored predetermined number of data at a predetermined timing. (Seki, T.)

NEUTRONIC REACTOR CONTROL ROD DRIVE APPARATUS

Science.gov (United States)

Oakes, L.C.; Walker, C.S.

1959-12-15

ABS>A suspension mechanism between a vertically movable nuclear reactor control rod and a rod extension, which also provides information for the operator or an automatic control signal, is described. A spring connects the rod extension to a drive shift. The extension of the spring indicates whether (1) the rod is at rest on the reactor, (2) the rod and extension are suspended, or (3) the extension alone is suspended, the spring controlling a 3-position electrical switch.

Turkey-hen amino acid composition of brain and eyes

International Nuclear Information System (INIS)

Adeyeye, E.I.

2015-01-01

The amino acids composition of the brain and eyes of the mature Turkey-hen (Meleagris gallopavo L.), were determined on dry weight basis. Total essential amino acids ranged from 35.1-36.0 g/100 g as 49.5-49.8% of the total amino acids. The amino acid score showed that lysine ranged from 0.76-0.91 (on whole hen.s egg comparison), 0.85-1.03 (on provisional essential amino acid scoring pattern), and 0.81-0.98 (on suggested requirement of the essential amino acid of a preschool child). The predicted protein efficiency ratio was 1.94-2.41, whilst essential amino acid index range was 1.06-1.08 and the calculated isoelectric point range was 3.97-4.18. The correlation coefficient (rxy) was positively high and significant at r = 0.01 for the total amino acids, amino acid scores (on the whole hen.s egg comparisons made) and the isoelectric point. On the whole, the eyes were better in 12/18 or 66.7% parameters of the amino acids than the brain of Turkey-Hen. (author)

Sturdy on Orbital TIG Welding Properties for Nuclear Fuel Test Rod

International Nuclear Information System (INIS)

Joung, Changyoung; Hong, Jintae; Kim, Kahye; Huh, Sungho

2014-01-01

We developed a precision TIG welding system that is able to weld the seam between end-caps and a fuel cladding tube for the nuclear fuel test rod and rig. This system can be mainly classified into an orbital TIG welder (AMI, M-207A) and a pressure chamber. The orbital TIG welder can be independently used, and it consists of a power supply unit, a microprocessor, water cooling unit, a gas supply unit and an orbital weld head. In this welder, the power supply unit mainly supplies GTAW power for a welding specimen and controls an arc starting of high frequency, supping of purge gas, arc rotation through the orbital TIG welding head, and automatic timing functions. In addition, the pressure chamber is used to make the welded surface of the cladding specimen clean with the inert gas filled inside the chamber. To precisely weld the cladding tube, a welding process needs to establish a schedule program for an orbital TIG welding. Therefore, the weld tests were performed on a cladding tube and dummy rods under various conditions. This paper describes not only test results on parameters of the purge gas flow rates and the chamber gas pressures for the orbital TIG welding, but also test results on the program establishment of an orbital TIG welding system to weld the fuel test rods. Various welding tests were performed to develop the orbital TIG welding techniques for the nuclear fuel test rod. The width of HAZ of a cladding specimen welded with the identical power during an orbital TIG welding cycle was continuously increased from a welded start-point to a weld end-point because of heat accumulation. The welding effect of the PGFR and CGP shows a relatively large difference for FSS and LSS. Each hole on the cladding specimens was formed in the 1bar CGP with the 20L/min PGFR but not made in the case of the PGFR of 10L/min in the CGP of 2bar. The optimum schedule program of the orbital TIG welding system to weld the nuclear fuel test rod was established through the program

Sturdy on Orbital TIG Welding Properties for Nuclear Fuel Test Rod

Energy Technology Data Exchange (ETDEWEB)

Joung, Changyoung; Hong, Jintae; Kim, Kahye; Huh, Sungho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-05-15

We developed a precision TIG welding system that is able to weld the seam between end-caps and a fuel cladding tube for the nuclear fuel test rod and rig. This system can be mainly classified into an orbital TIG welder (AMI, M-207A) and a pressure chamber. The orbital TIG welder can be independently used, and it consists of a power supply unit, a microprocessor, water cooling unit, a gas supply unit and an orbital weld head. In this welder, the power supply unit mainly supplies GTAW power for a welding specimen and controls an arc starting of high frequency, supping of purge gas, arc rotation through the orbital TIG welding head, and automatic timing functions. In addition, the pressure chamber is used to make the welded surface of the cladding specimen clean with the inert gas filled inside the chamber. To precisely weld the cladding tube, a welding process needs to establish a schedule program for an orbital TIG welding. Therefore, the weld tests were performed on a cladding tube and dummy rods under various conditions. This paper describes not only test results on parameters of the purge gas flow rates and the chamber gas pressures for the orbital TIG welding, but also test results on the program establishment of an orbital TIG welding system to weld the fuel test rods. Various welding tests were performed to develop the orbital TIG welding techniques for the nuclear fuel test rod. The width of HAZ of a cladding specimen welded with the identical power during an orbital TIG welding cycle was continuously increased from a welded start-point to a weld end-point because of heat accumulation. The welding effect of the PGFR and CGP shows a relatively large difference for FSS and LSS. Each hole on the cladding specimens was formed in the 1bar CGP with the 20L/min PGFR but not made in the case of the PGFR of 10L/min in the CGP of 2bar. The optimum schedule program of the orbital TIG welding system to weld the nuclear fuel test rod was established through the program

Simulation of vibration modes of the fuel rod damaged due to the grid-to-rod fretting wear

International Nuclear Information System (INIS)

Kim, Kyu Tae; Kim, Kyeong Koo; Jang, Young Ki; Lee, Kyou Seok

1997-01-01

The flow-induced fuel fretting wear observed in some PWRs mainly proceeds in the grid-to-rod contact positions. The grid-to-rod fretting wear in the PWR fuel assembly depends on grid-to-rod gap size, its axial profile and flow-induced vibration. This paper describes the GRIDFORCE program which generates the axially dependent grid-to-rod gap size as a function of burnup. The axially dependent grid-to-rod gap profiles are employed to predict the fuel rod vibration mode shapes by the ANSYS code. With the help of the Paidousis empirical formula, this paper also calculates the fuel rod vibration amplitudes under various supporting conditions, which indicates that the increase of the number of unsupported mid-grids will increase the fuel rod vibration amplitude. On the other hand, the comparison of the predicted vibration mode shapes and the observed mid-grid fretting wear pattern indicates that the 1st and 6th vibration mode shapes under the supporting inactive condition at the mid-grids can simulate the observed mid-grid fretting wear profile. This paper also proposes design guidelines against the grid-to-rod fretting wear. (author). 3 refs., 8 figs

Automated nuclear fuel rod pattern loading system

International Nuclear Information System (INIS)

Lambert, D.V.; Nylund, T.W.; Byers, J.W.; Haley, D.E. Jr.; Cioffi, J.V.

1991-01-01

This patent describes a method for loading fuel rods in a desired pattern. It comprises providing a supply of fuel rods of known enrichments; providing a magazine defining a matrix of elongated slots open at their forward ends for receiving fuel rods; defining a fuel rod feed path; receiving successively one at a time along the feed path fuel rods selected from the supply thereof; verifying successively one at a time along the feed path the identity of the selected fuel rods, the verifying including blocking passage of each selected fuel rod along the feed path until the identity of each selected fuel rod is confirmed as correct; feeding to the magazine successively one at a time along the feed path the selective and verified fuel rods; and supporting and moving the magazine along X-Y axes to successively align one at a time selected ones of the slots with the feed path for loading in the magazine the successive fuel rods in a desired enrichment pattern

Control rod drives

International Nuclear Information System (INIS)

Ikakura, Hiroaki.

1986-01-01

Purpose: To enable to direct disconnection of control rods upon abnormal temperature rise in the reactor thereby improve the reliability for the disconnecting operation in control rod drives for FBR type reactors upon emergency. Constitution: A diaphragm is disposed to the upper opening of a sealing vessel inserted to the hollow portion of an electromagnet and a rod is secured to the central position of the upper surface. A spring contacts are attached by way of an insulator to the inner surface at the lower portion of an extension pipe and connected with cables for supplying electric power sources respectively to a magnet. If the temperature in the reactor abnormally rises, liquid metals in the sealing vessel are expanded tending to extend the bellows downwardly. However, since they are attracted by the electromagnet, the thermal expansion of the liquid metals exert on the diaphragm prior to the bellows. Thus, the switch between the spring contacts is made open to attain the deenergized state to thereby disconnect the control rod and shutdown the neclear reactor. (Horiuchi, T.)

Method for compacting spent nuclear reactor fuel rods

International Nuclear Information System (INIS)

Wachter, W.J.

1988-01-01

In a nuclear reactor system which requires periodic physical manipulation of spent fuel rods, the method of compacting fuel rods from a fuel rod assembly is described. The method consists of: (1) removing the top end from the fuel rod assembly; (2) passing each of multiple fuel rod pulling elements in sequence through a fuel rod container and thence through respective consolidating passages in a fuel rod directing chamber; (3) engaging one of the pulling elements to the top end of each of the fuel rods; (4) drawing each of the pulling elements axially to draw the respective engaged fuel rods in one axial direction through the respective the passages in the chamber to thereby consolidate the fuel rods into a compacted configuration of a cross-sectional area smaller than the cross-sectional area occupied thereby within the fuel rod assembly; and (5) drawing all of the engaged fuel rods concurrently and substantially parallel to one another in the one axial direction into the fuel rod container while maintaining the compacted configuration whereby the fuel rods are aligned within the container in a fuel rod density of the the fuel rod assembly

Determination of transient temperature and heat flux on the surface of a reactor control rod based on temperature measurements at the interior points

International Nuclear Information System (INIS)

Cebula, Artur; Taler, Jan

2014-01-01

The paper presents heat transfer calculation results concerning a control rod of nuclear power plant. Apart from numerical calculation results, experimental heat transfer measurements of the control rod model are also presented. The control rod that is the object of interest is surrounded by a mixing region of hot and cold streams and, as a consequence, is subjected to thermal fluctuations. The paper describes a method based on the solution of the inverse heat conduction problem (IHCP) for determining heat flux on the outer surface of the rod. Numerical tests were conducted to validate the method by comparison of the results with the time changes of surface temperature and heat flux which were obtained from the computational fluid dynamics (CFD) simulation of the mixing process. A measuring instrument was designed to measure the heat flux at the outer surface of the control rod model. In addition, the principle of operation and construction of heat flux meter is presented in detail. -- Highlights: • Temperature and heat flux estimation during cooling of control rod are presented. • The inverse technique is based on the space marching method. • The instrument for surface heat flux measurement was manufactured and tested. • CFD simulations were used to validate the developed inverse technique. • Actual data were used to demonstrate practical applicability of the method

Stress Analysis of Single Spacer Grid Support considering Fuel Rod

Energy Technology Data Exchange (ETDEWEB)

Yoo, Y. G.; Jung, D. H.; Kim, J. H. [Chungnam National University, Daejeon (Korea, Republic of); Park, J. K.; Jeon, K. L. [Korea Nuclear Fuel, Daejeon (Korea, Republic of)

2010-10-15

Pressurized water reactor (PWR) nuclear fuel assembly is mainly composed of a top-end piece, a bottom-end piece, lots of fuel rods, and several spacer grids. Among them, the main function of spacer grid is protecting fuel rods from Fluid Induced Vibration (FIV). The cross section of spacer grid assembled by laser welding in upper and lower point. When the fuel rod inserted in spacer gird, spring and dimple and around of welded area got a stresses. The main hypothesis of this analysis is the boundary area of HAZ and base metal can get a lot of damage than other area by FIV. So, design factors of spacer grid mainly considered to preventing the fatigue failure in HAZ and spring and dimple of spacer grid. From previous researching, the environment in reactor verified. Pressure and temperature of light water observed 15MPa and 320 .deg. C, and vibration of the fuel rod observed within 0 {approx} 50Hz. In this study, mechanical properties of zirconium alloy that extracted from the test and the spacer grid model which used in the PWR were applied in stress analyzing. General-purpose finite element analysis program was used ANSYS Workbench 12.0.1 version. 3-D CAD program CATIA was used to create spacer grid model

Control rod drives

International Nuclear Information System (INIS)

Asano, Hiromitsu.

1979-01-01

Purpose: To drive control rods at an optimum safety speed corresponding to the reactor core output. Constitution: The reactor power is detected by a neutron detector and the output signal is applied to a process computer. The process computer issues a signal representing the reactor core output, which is converted through a function generator into a signal representing the safety speed of control rods. The converted signal is further supplied to a V/F converter and converted into a pulse signal. The pulse signal is inputted to a step motor driving circuit, which actuates a step motor to operate the control rods always at a safety speed corresponding to the reactor core power. (Furukawa, Y.)

Diagnostic device for failures in control rod drives

International Nuclear Information System (INIS)

Okutani, Tetsuro.

1982-01-01

Purpose: To enable to concretely point out a failure position when a failure might occur by diagnosing the failure without affecting the variation to the state of a reactor core. Constitution: A frequency switching circuit is provided in an inverter for controlling the rotating speed of a motor for discharging and charging a control rod. Then, a voltage detector is provided at asemiconductor switch provided between the inverter and the motor. When a high frequency control signal is input to the inverter in diagnosing a failure, the switching speed of the switch is accelerated, a current hardly flows through the motor, and even if the inverter is operated, the motor will not rotate. Thus, the failure of a control rod drive can be diagnosed without affecting any influence to the state of a reactor core. (Kamimura, M.)

Individual nuclear fuel rod weighing system

International Nuclear Information System (INIS)

Fogg, J. L.; Howell, C. A.; Smith, J. H.; Vining, G. E.

1985-01-01

An individual nuclear fuel rod weighing system for rods carried on a tray which moves along a materials handling conveyor. At a first tray position on the conveyor, a lifting device raises the rods off the tray and places them on an overhead ramp. A loading mechanism conveys the rods singly from the overhead ramp onto an overhead scale for individual weighing. When the tray is at a second position on the conveyor, a transfer apparatus transports each weighed rod from the scale back onto the tray

Energy Diplomacy of Turkey

Directory of Open Access Journals (Sweden)

Volkan Ozdemir

2016-01-01

Full Text Available The article deals with current issues of energy diplomacy of Turkey. The authors describe the main positive and negative results of Turkey's foreign energy policy in terms of the implementation of major energy projects. Geopolitical processes in the world, the conflict of interests of various countries in the political arena are important factors that affect the crude oil and natural gas pipeline projects. Particular attention is paid to the problems and prospects of cooperation between the Turkish Republic and the Russian Federation in the fuel and energy complex. The authors describe the interaction betweeen Russia and Turkey in the energy sector, including geo-economic interests of the countries in the Russian-Turkish gas dialogue. Turkey made efforts to position as an alternative gas supply route, taking advantage of concern about increasing Europe's dependence on Russian exports. Last years Turkey has set itself the important task - to turn from transit country into a regional gas hub. Ukrainian crisis increased the geostrategic importance of the Black Sea region to Russia, as well as strengthened the ambition of the Turkish side. The authors also highlight the prospects of the natural gas pipeline project from Russia via the Black Sea to Turkey and to the Turkish-Greek border, which named "Turkish stream". This project was frozen in terms of military and political processes at the end of 2015 in Syria.

Measuring device for control rod driving time

International Nuclear Information System (INIS)

Tanaka, Kazuhiko; Hanabusa, Masatoshi.

1993-01-01

The present invention concerns a measuring device for control driving time having a function capable of measuring a selected control rod driving time and measuring an entire control rod driving time simultaneously. A calculation means and a store means for the selected rod control rod driving time, and a calculation means and a store means for the entire control rod driving time are disposed individually. Each of them measures the driving time and stores the data independent of each other based on a selected control rod insert ion signal and an entire control rod insertion signal. Even if insertion of selected and entire control rods overlaps, each of the control rod driving times can be measured reliably to provide an advantageous effect capable of more accurately conducting safety evaluation for the nuclear reactor based on the result of the measurement. (N.H.)

Characterization of Clostridium perfringens isolates from healthy turkeys and from turkeys with necrotic enteritis

DEFF Research Database (Denmark)

Lyhs, Ulrike; Perko-Mäkelä, P.; Kallio, H.

2013-01-01

from 1998 to 2012. Furthermore, C. perfringens isolates from healthy and diseased turkeys were characterized and their genetic diversity was investigated using pulsed-field gel electrophoresis (PFGE). Isolates (n = 212) from birds with necrotic gut lesions and from healthy flocks of 30 commercial...... turkey farms were characterized for the presence of cpa, cpb, iA, etx, cpb2, and cpe and netB genes. A total of 93 C. perfringens isolates, including 55 from birds with necrotic gut lesions and 38 from healthy birds from 13 different farms, were analyzed with PFGE. All contract turkey farmers (n = 48......) of a turkey company that produces 99% of domestic turkey meat in Finland were interviewed about background information, management at the farm, and stress factors related to NE outbreaks. Pulsed-field gel electrophoresis analysis with SmaI restriction enzyme resulted in 30 PFGE patterns among the 92 C...

Growth and Morphology of Rod Eutectics

Energy Technology Data Exchange (ETDEWEB)

Jing Teng; Shan Liu; R. Trivedi

2008-03-17

The formation of rod eutectic microstructure is investigated systematically in a succinonitrile-camphor alloy of eutectic composition by using the directional solidification technique. A new rod eutectic configuration is observed in which the rods form with elliptical cylindrical shape. Two different orientations of the ellipse are observed that differ by a 90{sup o} rotation such that the major and the minor axes are interchanged. Critical experiments in thin samples, where a single layer of rods forms, show that the spacing and orientation of the elliptic rods are governed by the growth rate and the sample thickness. In thicker samples, multi layers of rods form with circular cross-section and the scaling law between the spacing and velocity predicted by the Jackson and Hunt model is validated. A theoretical model is developed for a two-dimensional array of elliptical rods that are arranged in a hexagonal or a square array, and the results are shown to be consistent with the experimental observations. The model of elliptic rods is also shown to reduce to that for the circular rod eutectic when the lengths of the two axes are equal, and to the lamellar eutectic model when one of the axes is much larger than the other one.

Status of rod consolidation, 1988

International Nuclear Information System (INIS)

Bailey, W.J.

1989-01-01

It is estimated that the spent fuel storage pools at some domestic light-water reactors will run out of space before 2003, the year that the US Department of Energy currently predicts it will have a repository available. Of the methods being studied to alleviate the problem, rod consolidation is one of the leading candidates for achieving more efficient use of existing space in spent fuel storage pools. Rod consolidation involves mechanically removing all the fuel rods from the fuel assembly hardware (i.e., the structural components) and placing the fuel rods in a close-packed array in a canister without space grids. A typical goal of rod consolidation systems is to insert the fuel rods from two fuel assemblies into a canister that has the same exterior dimensions as one standard fuel assembly (i.e., to achieve a consolidation or compaction ratio of 2:1) and to compact the nonfuel-bearing structural components from those two fuel assemblies by a factor of 10 to 20. This report provides an overview of the current status of rod consolidation in the United States and a small amount of information on related activities in other countries. 85 refs., 36 figs., 5 tabs

Inspecting method for fuel rods

International Nuclear Information System (INIS)

Watanabe, Masaaki; Kogure, Sumio.

1976-01-01

Purpose: To precisely detect the response of flaw in clad tube and submerged fuel pellets from a relationship between the surface of fuel rod and internal signal. Constitution: Ultrasonic reflected waves from the surface of fuel rods and the interior are detected and either one of fuel rod or ultrasonic flaw detecting contact is rotated to thereby precisely detect the response of the flaw of clad tube and submerged fuel pellets from a relationship between said surface and the interior. It will be noted that the ultrasonic flaw detecting contact used is of the line-focus type, the incident angle of ultrasonic wave from the ultrasonic flaw detecting contact relative to the fuel rod is the angle of skew, that is, the ultrasonic flaw detecting contact is not perpendicular to a center axis of the fuel rod but is slightly displace. That is, the use of the aforesaid contact may facilitate discrimination between the surface flaw of the fuel rod and the response of submergence, and in addition, the employment of the aforesaid incident angle makes it hard to receive reflected waves from the surface of the fuel rod which is great in terms of energy to facilitate discrimination of waves responsive to submergence. (Kawakami, Y.)

Rope wind-up type control rod

International Nuclear Information System (INIS)

Tsuji, Teruaki; Watanabe, Shigeru.

1979-01-01

Purpose: To hold a control rod at a certain position even if the sealed cover of the rod drive mechanism should fail. Constitution: A plurality of friction plates, engaging wheels and a threaded shaft are provided to the wind-up drum for winding up a rope which moves the control rod up and down. While the control rod is adapted to drop by its own weight upon insertion, it is adapted to stop at a predetermined position exactly with no shocks by gradually increasing braking force by the sliding friction caused from the friction plates or the like. A ratch mechanism is provided to the upper portion of the control rod so that the top of the ratch piece may automatically engage the guide passage wall of the control rod upon uncontrolled running of the control rod to prevent further uncontrolled running thereof. (Ikeda, J.)

Towards Viscoplastic Constitutive Models for Cosserat Rods

Directory of Open Access Journals (Sweden)

Dörlich Vanessa

2016-06-01

Full Text Available Flexible, slender structures like cables, hoses or wires can be described by the geometrically exact Cosserat rod theory. Due to their complex multilayer structure, consisting of various materials, viscoplastic behavior has to be expected for cables under load. Classical experiments like uniaxial tension, torsion or three-point bending already show that the behavior of e.g. electric cables is viscoplastic. A suitable constitutive law for the observed load case is crucial for a realistic simulation of the deformation of a component. Consequently, this contribution aims at a viscoplastic constitutive law formulated in the terms of sectional quantities of Cosserat rods. Since the loading of cables in applications is in most cases not represented by these mostly uniaxial classical experiments, but rather multiaxial, new experiments for cables have to be designed. They have to illustrate viscoplastic effects, enable access to (viscoplastic material parameters and account for coupling effects between different deformation modes. This work focuses on the design of such experiments.

ELECTROMAGNETIC APPARATUS FOR MOVING A ROD

Science.gov (United States)

Young, J.N.

1958-04-22

An electromagnetic apparatus for moving a rod-like member in small steps in either direction is described. The invention has particular application in the reactor field where the reactor control rods must be moved only a small distance and where the use of mechanical couplings is impractical due to the high- pressure seals required. A neutron-absorbing rod is mounted in a housing with gripping uaits that engage the rod, and coils for magnetizing the gripping units to make them grip, shift, and release the rod are located outside the housing.

Individual nuclear fuel rod weighing system

International Nuclear Information System (INIS)

Fogg, J.L.; Smith, J.H.; Vining, G.E.; Howell, C.A.

1985-01-01

An individual nuclear fuel rod weighing system for rods carried on a tray which moves along a materials handling conveyor is discussed. At a first tray position on the conveyor, a lifting device raises the rods off the tray and places them on an overhead ramp. A loading mechanism conveys the rods singly from the overhead ramp onto an overhead scale for individual weighing. When the tray is at a second position on the conveyor, a transfer apparatus transports each weighed rod from the scale back onto the tray

The effect of the fuel rod friction force to the fuel assembly lateral mechanical characteristics

International Nuclear Information System (INIS)

Ha, Dong Geun; Jeon, Sang Youn; Suh, Jung Min

2012-01-01

The Fuel Assembly (FA) for light water reactor consists of hundreds of fuel rods, guide tubes, spacer grids, top/bottom nozzles. The guide tubes transmit vertical loads between the top and bottom nozzles, position the fuel rod support grids vertically, react the loads from the fuel rods that are applied to the grids, and provide some of the lateral load capability for the overall fuel assembly. The guide tubes are the structural members of the skeleton assembly. And the spacer grids maintain the fuel rod array by providing positive lateral restraint to the fuel rod but only frictional restraint in the axial direction. Figure 1 shows the outline of skeleton, FA and the location of guide tubes in the view of cross section. 17x17 FA has 24 guide tubes and one instrumentation tube. When the FA is in reactor, the lateral stiffness is one of very important factors from the view point of in reactor integrity of fuel assembly such as guarantee of the cool able geometry, the control rod insertion etc. The lateral stiffness of FA is mainly determined by skeleton lateral stiffness. And the fuel rods loaded in the spacer grids reinforce the FA lateral stiffness. Generally, fuel rods and spacer grids create the nonlinear friction force between fuel rod tube and grid spring/dimple against external lateral force of FA. Thus, it is necessary to study the contribution of the fuel rods friction force to the FA lateral stiffness. So, this paper is to show how much amount of the fuel rod grid interaction contributes to the FA lateral stiffness based on the test results

Control rods in LMFBRs: a physics assessment

International Nuclear Information System (INIS)

McFarlane, H.F.; Collins, P.J.

1982-08-01

This physics assessment is based on roughly 300 control rod worth measurements in ZPPR from 1972 to 1981. All ZPPR assemblies simulated mixed-oxide LMFBRs, representing sizes of 350, 700, and 900 MWe. Control rod worth measurements included single rods, various combinations of rods, and Ta and Eu rods. Additional measurements studied variations in B 4 C enrichment, rod interaction effects, variations in rod geometry, neutron streaming in sodium-filled channels, and axial worth profiles. Analyses were done with design-equivalent methods, using ENDF/B Version IV data. Some computations for the sensitivities to approximations in the methods have been included. Comparisons of these analyses with the experiments have allowed the status of control rod physics in the US to be clearly defined

Measurements of Burnout Conditions for Flow of Boiling Water in Vertical 3-Rod and 7-Rod Clusters

Energy Technology Data Exchange (ETDEWEB)

Becker, Kurt M; Hernborg, G; Flinta, J E

1964-08-15

The present report deals with measurements of burnout conditions for flow of boiling water in vertical 3-rod and 7-rod clusters. Data were obtained,in respect of heating the rods only, as well as for simultaneous uniform and non-uniform heating of the rods and the shroud. Totally, 520 runs were performed. In the case of equal heat fluxes on all surfaces of the channels, burnout always occurred on the rods, and the data were low by a factor of about 1.3 compared with round duct data. When only the rods were heated, the data showed very low burnout values in comparison with the results for total uniform heating and round ducts. This disagreement was explained by considering the climbing film flow model and the fact that only a fraction of the channel perimeter was heated. For simultaneous and non-uniform heating of the rods and the shroud it was found that the shroud could be overloaded up to 50 per cent without reducing the margin of safety in respect of burnout for the rod cluster. Finally, a correlation for predicting burnout conditions in round ducts, annuli and rod clusters has been presented. This correlation predicts the burnout heat fluxes for the present measurements and previously obtained annuli measurements within {+-} 5 per cent.

Self-Assembly of Rod-Coil Block Copolymers

National Research Council Canada - National Science Library

Jenekhe, S

1999-01-01

... the self-assembly of new rod-coil diblock, rod- coil-rod triblock, and coil-rod-coil triblock copolymers from solution and the resulting discrete and periodic mesostmctares with sizes in the 100...

Restructuring of Turkey's electricity market and the share of hydropower energy: The case of the Eastern Black Sea Basin

International Nuclear Information System (INIS)

Uzlu, Ergun; Koemuercue, Murat ihsan; Akpinar, Adem

2011-01-01

This paper presents the historical development of Turkey's electricity power sector, the efforts for introducing competition in the power industry in Turkey, and the concerns regarding restructuring in Turkey. The contribution of the hydropower energy potential in Turkey to the reconstruction of the electricity structure in Turkey is also investigated. Then, among the 25 hydrological basins in Turkey, the Eastern Black Sea Basin located in the northeast of Turkey, which has great advantages from the view point of small hydropower potential or hydropower potential without storage, is chosen as the case study to carry out some investigations concerning its potential and to analyze the contribution of the private sector (the corporate body) in regard to the development of hydro potential in this basin within the scope of the 4628 Electricity Market Law. With this law, concerning the restructuring of the electricity market, private sector investments in this segment have increased. In total, 1524 hydroelectric power projects with 22 360 MW installed capacity has been implemented until January 22nd, 2009 and this figure is continuously rising. (author)

Ejected control rod and rods drop measurements during Mochovce startup physical tests

International Nuclear Information System (INIS)

Minarcin, Miroslav; Elko, Marek

1998-01-01

Paper deals with measurements of asymmetric reactivity insertion into the reactor core that were carried out during physical startup tests of Mochovce Unit 1 in June 1998. Control rods worth measurements with one and two rods s tucked in upper limit and worth measurement of one control rod from group 6 'ejected' from the reactor core are discussed. During the experiments neutron flux was measured by four ionisation chambers (three of them were placed symmetrically around the reactor core). Results of measurements and influence of asymmetric reactivity influence on ionisation chambers response are presented in the paper. (Authors)

Quivers For Special Fuel Rods-Disposal Of Special Fuel Rods In CASTOR V Casks

International Nuclear Information System (INIS)

Bannani, Amin; Cebula, Wojciech; Buchmuller, Olga; Huggenberg, Roland; Helmut Kuhl

2015-01-01

While GNS casks of the CASTOR family are a suitable means to transfer fuel assemblies (FA) from the NPP to an interim dry storage site, Germanys phase-out of nuclear energy has triggered the demand for an additional solution to dispose of special fuel rods (SFR), normally remaining in the fuel pond until the final shutdown of the NPP. SFR are fuel rods that had to be removed from fuel assemblies mainly due to their special condition, e. g. damages in the cladding of the fuel rods which may have occurred during reactor operations. SFR are usually stored in the spent fuel pond after they are removed from the FA. The quiver for special fuel rods features a robust yet simple design, with a high mechanical stability, a reliable leak-tightness and large safety margins for future requirements on safety analysis. The quiver for special fuel rods can be easily adapted to a large variety of different damaged fuel rods and tailored to the specific need of the customer. The quiver for special fuel rods is adaptable e.g. in length and diameter for use in other types of transport and storage casks and is applicable in other countries as well. The overall concept presented here is a first of its kind solution for the disposal of SFRs via Castor V-casks. This provides an important precondition in achieving the status 'free from nuclear fuel' of the shut down German NPPs

Quivers For Special Fuel Rods-Disposal Of Special Fuel Rods In CASTOR V Casks

Energy Technology Data Exchange (ETDEWEB)

Bannani, Amin; Cebula, Wojciech; Buchmuller, Olga; Huggenberg, Roland [GNS, Essen (Germany); Helmut Kuhl [WTI, Julich (Germany)

2015-05-15

While GNS casks of the CASTOR family are a suitable means to transfer fuel assemblies (FA) from the NPP to an interim dry storage site, Germanys phase-out of nuclear energy has triggered the demand for an additional solution to dispose of special fuel rods (SFR), normally remaining in the fuel pond until the final shutdown of the NPP. SFR are fuel rods that had to be removed from fuel assemblies mainly due to their special condition, e. g. damages in the cladding of the fuel rods which may have occurred during reactor operations. SFR are usually stored in the spent fuel pond after they are removed from the FA. The quiver for special fuel rods features a robust yet simple design, with a high mechanical stability, a reliable leak-tightness and large safety margins for future requirements on safety analysis. The quiver for special fuel rods can be easily adapted to a large variety of different damaged fuel rods and tailored to the specific need of the customer. The quiver for special fuel rods is adaptable e.g. in length and diameter for use in other types of transport and storage casks and is applicable in other countries as well. The overall concept presented here is a first of its kind solution for the disposal of SFRs via Castor V-casks. This provides an important precondition in achieving the status 'free from nuclear fuel' of the shut down German NPPs.

Monitoring device for withdrawing control rods

International Nuclear Information System (INIS)

Higashigawa, Yuichi.

1985-01-01

Purpose: To improve the sensitivity and the responsivity to an equivalent extent to those in the case where local power range monitors are densely arranged near each of the control rods, with no actual but pseudo increase of the number of local power range monitors. Constitution: The monitor arrangement is patterned by utilizing the symmetricity of the reactor core and stored in a monitor designating device. The symmetricity of control rods to be selected and withdrawn by an operator is judged by a control rod symmetry monitoring device, while the symmetricity of the withdrawn control rods is judged by a control rod withdrawal state monitoring device. Then, only when both of the devices judge the symmetricity, the control rods are subjected to gang driving by the control rod drive mechanisms. In this way, monitoring at a high sensitivity and responsivity is enabled with no increase for the number of monitors. (Yoshino, Y.)

Nondestructive assay of HTGR fuel rods

International Nuclear Information System (INIS)

Menlove, H.O.

1974-01-01

Performance characteristics of three different radioactive source NDA systems are compared for the assay of HTGR fuel rods and stacks of rods. These systems include the fast neutron Sb-Be assay system, the 252 Cf ''Shuffler,'' and the thermal neutron PAPAS assay system. Studies have been made to determinethe perturbation on the measurements from particle size, kernel Th/U ratio, thorium content, and hydrogen content. In addition to the total 235 U determination, the pellet-to-pellet or rod-to-rod uniformity of HTGR fuel rod stacks has been measured by counting the delayed gamma rays with a NaI through-hole in the PAPAS system. These measurements showed that rod substitutions can be detected easily in a fuel stack, and that detailed information is available on the loading variations in a uniform stack. Using a 1.0 mg 252 Cf source, assay rates of 2 to 4 rods/s are possible, thus facilitating measurement of 100 percent of a plant's throughput. (U.S.)

Turkey: A Geostrategic Analysis

National Research Council Canada - National Science Library

Fanale, Rosalie A

2001-01-01

...] America"s primary national security interest in Turkey is regional stability. U.S. strategy aims for Turkey to be a strong regional player, able to act in support of U.S. interests in a troubled region.

Tuning topological phase transitions in hexagonal photonic lattices made of triangular rods

Science.gov (United States)

Chan, Hsun-Chi; Guo, Guang-Yu

2018-01-01

In this paper we study topological phases in a two-dimensional photonic crystal with broken time (T ) and parity (P ) symmetries by performing calculations of band structures, Berry curvatures, Chern numbers, edge states, and also numerical simulations of light propagation in the edge modes. Specifically, we consider a hexagonal lattice consisting of triangular gyromagnetic rods. Here the gyromagnetic material breaks T symmetry while the triangular rods break P symmetry. Interestingly, we find that the crystal could host quantum anomalous Hall (QAH) phases with different gap Chern numbers (Cg) including | Cg|>1 as well as quantum valley Hall (QVH) phases with contrasting valley Chern numbers (Cv), depending on the orientation of the triangular rods. Furthermore, phase transitions among these topological phases, such as from QAH to QVH and vice versa, can be engineered by a simple rotation of the rods. Our band theoretical analyses reveal that the Dirac nodes at the K and K' valleys in the momentum space are produced and protected by the mirror symmetry (my) instead of the P symmetry, and they become gapped when either T or my symmetry is broken, resulting in a QAH or QVH phase, respectively. Moreover, a high Chern number (Cg=-2 ) QAH phase is generated by gapping triply degenerate nodal points rather than pairs of Dirac points by breaking T symmetry. Our proposed photonic crystal thus provides a platform for investigating intriguing topological phenomena which may be challenging to realize in electronic systems, and also has promising potentials for device applications in photonics such as reflection-free one-way waveguides and topological photonic circuits.

Inspection system for Zircaloy clad fuel rods

International Nuclear Information System (INIS)

Yancey, M.E.; Porter, E.H.; Hansen, H.R.

1975-10-01

A description is presented of the design, development, and performance of a remote scanning system for nondestructive examination of fuel rods. Characteristics that are examined include microcracking of fuel rod cladding, fuel-cladding interaction, cladding thickness, fuel rod diameter variation, and fuel rod bowing. Microcracking of both the inner and outer fuel rod surfaces and variations in wall thickness are detected by using a pulsed eddy current technique developed by Argonne National Laboratory (ANL). Fuel rod diameter variation and fuel rod bowing are detected by using two linear variable differential transformers (LVDTs) and a signal conditioning system. The system's mechanical features include variable scanning speeds, a precision indexing system, and a servomechanism to maintain proper probe alignment. Initial results indicate that the system is a very useful mechanism for characterizing irradiated fuel rods

An evaluation of control rod motion simulator of research reactor

International Nuclear Information System (INIS)

Sanda

2010-01-01

Motion simulator for rod control research reactor has been carried out using a servo motor. Reactor rod motion control at any point should be in the right position, one of the motors that can move in a precise and correct is the servo motor. To ensure that the servo motor to move in accordance with the desired program, then the servo motor function test should be carried out to ensure having good performance. Tests carried out on meshes stress disorder, the load is stable within a certain period and travel time safety control rod up and down, travel time regulating control rods up and down and travel time compensation control rods up and down. In testing the breakdown voltage V out nets at 24 V, 6.5 A with 12 Q load deviation obtained V0= V1 = 0.1% and 0.65% and for the stability of the load in a certain time deviation V = 0.7125% , next to the breakdown voltage V out nets at 12 V, 4.2 A with a 6 Q load deviation obtained V0= V1 = 0.275% and 1.158% for the stability of the load in a certain time deviation V = 1.463% and the net-voltage noise nets on V out 24 V, 4.5 A with 12 Q load deviation obtained V0 = V1 = 0.196% and 0.496% and for the stability of the load in a certain time deviation V = 0.3625%. While the travel time of a safety control rod up and down, up and down the regulator and compensation rise and fall showed a steady linear graph. The results show that the performance of the servo motor is very stable with the working area below the tolerance limit, it is 5% - 10%.(author)

Seismic scrammability of HTTR control rods

International Nuclear Information System (INIS)

Nishiguchi, I.; Iyoku, T.; Ito, N.; Watanabe, Y.; Araki, T.; Katagiri, S.

1990-01-01

Scrammability tests on HTTR (High-Temperature Engineering Test Reactor) control rods under seismic conditions have been carried out and seismic conditions influences on scram time as well as functional integrity were examined. A control rod drive located in a stand-pipe at the top of a reactor vessel, raises and lowers a pair of control rods by suspension cables. Each flexible control rod consists of 10 neutron absorber sections held together by a metal spine passing through the center. It falls into a hole in graphite blocks due to gravity at scram. In the tests, a full scale control rod drive and a pair of control rods were employed with a column of graphite blocks in which holes for rods were formed. Blocks misalignment and contact with the hole surface during earthquakes were considered as major causes of disturbance in scram time. Therefore, the following parameters were set up in the tests: excitation direction, combination or horizontal and vertical excitation, acceleration, frequency and block to block gaps. Main results obtained from tests are as follow. 1) Every scram time obtained under the design conditions was within 6 seconds. On the contrary, the scram times were 5.2 seconds when there were no vibration. Therefore, it was concluded that the seismic effects on scram time were not significant. 2) Scram time became longer with increase in both acceleration and horizontal excitation frequency, and control rods fell very smoothly without any jerkiness. This suggests that collision between control rods and hole surface is the main disturbing factor of falling motion. 3) Mechanical and functional integrity of control rod drive mechanism, control rods and graphite blocks was confirmed after 140 seismic scrammability tests. (author). 10 figs, 1 tab

Patient-specific Distraction Regimen to Avoid Growth-rod Failure.

Science.gov (United States)

Agarwal, Aakash; Jayaswal, Arvind; Goel, Vijay K; Agarwal, Anand K

2018-02-15

A finite element study to establish the relationship between patient's curve flexibility (determined using curve correction under gravity) in juvenile idiopathic scoliosis and the required distraction frequency to avoid growth rod fracture, as a function of time. To perform a parametric analysis using a juvenile scoliotic spine model (single mid-thoracic curve with the apex at the eighth thoracic vertebra) and establish the relationship between curve flexibility (determined using curve correction under gravity) and the distraction interval that allows a higher factor of safety for the growth rods. Previous studies have shown that frequent distraction with smaller magnitude of distractions are less likely to result in rod failure. However there has not been any methodology or a chart provided to apply this knowledge on to the individual patients that undergo the treatment. This study aims to fill in that gap. The parametric study was performed by varying the material properties of the disc, hence altering the axial stiffness of the scoliotic spine model. The stresses on the rod were found to increase with increased axial stiffness of the spine, and this resulted in the increase of required optimal frequency to achieve a factor of safety of two for growth rods. A relationship between the percentage correction in Cobb's angle due to gravity alone, and the required distraction interval for limiting the maximum von Mises stress to 255 MPa on the growth rods was established. The distraction interval required to limit the stresses to the selected nominal value reduces with increase in stiffness of the spine. Furthermore, the appropriate distraction interval reduces for each model as the spine becomes stiffer with time (autofusion). This points to the fact the optimal distraction frequency is a time-dependent variable that must be achieved to keep the maximum von Mises stress under the specified factor of safety. The current study demonstrates the possibility of

Control rod testing apparatus

International Nuclear Information System (INIS)

Gaunt, R.R.; Ashman, C.M.

1987-01-01

A control rod testing apparatus is described comprising: a first guide means having a vertical cylindrical opening for grossly guiding a control rod; a second guide means having a vertical cylindrical opening for grossly guiding a control rod. The first and second guide means are supported at axially spaced locations with the openings coaxial; and a substantially cylindrical subassembly having a vertical cylindrical opening therethrough. The subassembly is trapped coaxial with and between the first and second guide means, and the subassembly radially floats with respect to the first and second guide means

Establishment and assessment of CHF data base for square-lattice rod bundles

International Nuclear Information System (INIS)

Hwang, Dae Hyun; Seo, K. W.; Kim, K. K.; Zee, S. Q.

2002-02-01

A CHF data base is constructed for square-lattice rod bundles, and assessed with various existing CHF prediction models. The CHF data base consists of 10725 data points obtained from 147 test bundles with uniform axial power distributions and 29 test bundles with non-uniform axial power distributions. The local thermal-hydraulic conditions in the subchannels are calculated by employing a subchannel analysis code MATRA. The influence of turbulent mixing parameter on CHF is evaluated quantitatively for selected test bundles with representative cross sectional configurations. The performance of various CHF prediction models including empirical correlations for round tubes or rod bundles, theoretical DNB models such as sublayer dryout model and bubble crowding model, and CHF lookup table for round tubes, are assessed for the localized rod bundle CHF data base. In view of the analysis result, it reveals that the 1995 AECL-IPPE CHF lookup table method is one of promising models in the aspect of the prediction accuracy and the applicable range. As the result of analysis employing the CHF lookup table for 9113 data points with uniform axial heat profile, the mean and the standard deviation of P/M are calculated as 1.003 and 0.115 by HBM, 1.022 and 0.319 by DSM respectively

Development of the automatic control rod operation system for JOYO. Verification of automatic control rod operation guide system

International Nuclear Information System (INIS)

Terakado, Tsuguo; Suzuki, Shinya; Kawai, Masashi; Aoki, Hiroshi; Ohkubo, Toshiyuki

1999-10-01

The automatic control rod operation system was developed to control the JOYO reactor power automatically in all operation modes(critical approach, cooling system heat up, power ascent, power descent), development began in 1989. Prior to applying the system, verification tests of the automatic control rod operation guide system was conducted during 32nd duty cycles of JOYO' from Dec. 1997 to Feb. 1998. The automatic control rod operation guide system consists of the control rod operation guide function and the plant operation guide function. The control rod operation guide function provides information on control rod movement and position, while the plant operation guide function provide guidance for plant operations corresponding to reactor power changes(power ascent or power descent). Control rod insertion or withdrawing are predicted by fuzzy algorithms. (J.P.N.)

Control rod drive shaft latch

International Nuclear Information System (INIS)

Thorp, A.G. II.

1976-01-01

A latch mechanism is operated by differential pressure on a piston to engage the drive shaft for a control rod in a nuclear reactor, thereby preventing the control rod from being ejected from the reactor in case of failure of the control rod drive mechanism housing which is subjected to the internal pressure in the reactor vessel. 6 claims, 4 drawing figures

Measurements of Burnout Conditions for Flow of Boiling Water in Vertical 3-Rod and 7-Rod Clusters

International Nuclear Information System (INIS)

Becker, Kurt M.; Hernborg, G.; Flinta, J.E.

1964-08-01

The present report deals with measurements of burnout conditions for flow of boiling water in vertical 3-rod and 7-rod clusters. Data were obtained,in respect of heating the rods only, as well as for simultaneous uniform and non-uniform heating of the rods and the shroud. Totally, 520 runs were performed. In the case of equal heat fluxes on all surfaces of the channels, burnout always occurred on the rods, and the data were low by a factor of about 1.3 compared with round duct data. When only the rods were heated, the data showed very low burnout values in comparison with the results for total uniform heating and round ducts. This disagreement was explained by considering the climbing film flow model and the fact that only a fraction of the channel perimeter was heated. For simultaneous and non-uniform heating of the rods and the shroud it was found that the shroud could be overloaded up to 50 per cent without reducing the margin of safety in respect of burnout for the rod cluster. Finally, a correlation for predicting burnout conditions in round ducts, annuli and rod clusters has been presented. This correlation predicts the burnout heat fluxes for the present measurements and previously obtained annuli measurements within ± 5 per cent

Power Consumption Estimation Using Artificial Neural Networks: The Case of Turkey

Directory of Open Access Journals (Sweden)

Havva Hilal Metin

2018-06-01

Full Text Available A significant proportion of the world energy consumption is by developing countries. As a developing country, Turkey is one of the leading countries in terms of the increase in energy demand. According to the data from the Ministry of Energy and Natural Resources, Turkey is the country with the greatest increase in demand after China in electricity and natural gas consumption since 2000. In 1970, the ratio of total energy production to consumption in Turkey was 76%. In year 2000, this ratio dropped down to 35%, in year 2010 to 26% and predicted to come down to 23% by year 2020. This situation indicates an increase in Turkey’s energy dependency every passing year and the need to implement solutions to reduce this dependency. Today, electric energy has become a very critical and indispensable part of the development of technology. Production and consumption of electrical energy, which facilitates human life and increases labour productivity, are increasing every year. Electricity is a versatile and easily controlled form of energy. Electricity is practically non-existent and non-polluting at the point of use. Electricity can be cleanly produced by completely renewable methods such as wind, water and sunlight at the production point. Electricity market has a unique feature compared to other commodities. This feature requires the consumption of electricity when it is produced. Forecasting the future consumption of electricity in Turkey is crucial in making strategic plans for the future and taking the necessary measures. In Turkey, the consumption of electricity in the estimation studies were generally observed that the use of long-term electricity consumption prediction method of neural networks. In some studies, the results obtained by artificial neural network method are compared with Box-Jenkins models and regression technique. As a result of comparison, artificial neural networks seem to be a good predictor of electricity consumption. In this

Reconstitutable control rod spider assembly

International Nuclear Information System (INIS)

Shallenberger, J.M.; Ferian, S.J.

1990-01-01

A reconstitutable control rod/spider assembly includes a hollow connecting finger of the spider having a pair of opposing flat segments formed on the interior thereof and engaging a pair of opposing flat sectors formed on the exterior of a stem extending form the upper end of control rod. The stem also has an externally-threaded portion engaging a nut and a pilot aligning portion for the nut. The nut has a radially flexible and expandable thread-defining element captured in its bore. The segments and sectors allow the rod to be removed and reattached after turning through 180 0 to allow more even wear on the rod. (author)

Estimation of irradiated control rod worth

International Nuclear Information System (INIS)

Varvayanni, M.; Catsaros, N.; Antonopoulos-Domis, M.

2009-01-01

When depleted control rods are planned to be used in new core configurations, their worth has to be accurately predicted in order to deduce key design and safety parameters such as the available shutdown margin. In this work a methodology is suggested for the derivation of the distributed absorbing capacity of a depleted rod, useful in the case that the level of detail that is known about the irradiation history of the control rod does not allow an accurate calculation of the absorber's burnup. The suggested methodology is based on measurements of the rod's worth carried out in the former core configuration and on corresponding calculations based on the original (before first irradiation) absorber concentration. The methodology is formulated for the general case of the multi-group theory; it is successfully tested for the one-group approximation, for a depleted control rod of the Greek Research Reactor, containing five neutron absorbers. The computations reproduce satisfactorily the irradiated rod worth measurements, practically eliminating the discrepancy of the total rod worth, compared to the computations based on the nominal absorber densities.

Rod cluster having improved vane configuration

International Nuclear Information System (INIS)

Shockling, L.A.; Francis, T.A.

1989-01-01

This patent describes a pressurized water reactor vessel, the vessel defining a predetermined axial direction of the flow of coolant therewithin and having plural spider assemblies supporting, for vertical movement within the vessel, respective clusters of rods in spaced, parallel axial relationship, parallel to the predetermined axial direction of coolant flow, and a rod guide for each spider assembly and respective cluster of rods. The rod guide having horizontally oriented support plates therewithin, each plate having an interior opening for accommodating axial movement therethrough of the spider assembly and respective cluster of rods. The opening defining plural radially extending channels and corresponding parallel interior wall surfaces of the support plate

Sucker rod motor

Energy Technology Data Exchange (ETDEWEB)

Radzalov, N N; Radzhabov, N A

1983-01-01

The motor consists of rollers mounted on the wellmouth and connected by a flexible rink. Reciprocating mechanism is in the form of a horizontal non-mobile single-side operation cylinder, inside which a plunger and rod are mounted. The working housing of the hydrocylinder is connected to a gas-hydr aulic batter, and when running is connected via plunger to the high pressure source; running in reverse it is connected with a safety valve and automatic control unit. The unit is equipped with a reducer and a mechanical transformer consisting of screw and nut, and which is shutoff with a single-side lining. The plunger rod consists of an auger-like unit. The high pressure source is provided by the injection line of the sucker rod that has been equipped with a reverse valve.

Duke Power Company's control rod wear program

International Nuclear Information System (INIS)

Culp, D.C.; Kitlan, M.S. Jr.

1990-01-01

Recent examinations performed at several foreign and domestic pressurized water reactors have identified significant control rod cladding wear, leading to the conclusion that previously believed control rod lifetimes are not attainable. To monitor control rod performance and reduce safety concerns associated with wear, Duke Power Company has developed a comprehensive control rod wear program for Ag-In-Cd and boron carbide (B 4 C) rods at the McGuire and Catawba nuclear stations. Duke Power currently uses the Westinghouse 17 x 17 Ag-In-Cd control rod design at McGuire Unit 1 and the Westinghouse 17 x 17 hybrid B 4 C control rod design with a Ag-In-Cd tip at McGuire Unit 2 and Catawba Units 1 and 2. The designs are similar, with the exception of the absorber material and clad thickness. There are 53 control rods per unit

Fuel rod pellet loading head

International Nuclear Information System (INIS)

Howell, T.E.

1975-01-01

An assembly for loading nuclear fuel pellets into a fuel rod comprising a loading head for feeding pellets into the open end of the rod is described. The pellets rest in a perforated substantially V-shaped seat through which air may be drawn for removal of chips and dust. The rod is held in place in an adjustable notched locator which permits alignment with the pellets

IS TURKEY READY TO JOINT THE EUROPEAN FISCAL UNION?

Directory of Open Access Journals (Sweden)

Georg Friedrich SIMET

2012-12-01

Full Text Available Since Turkey was officially recognized as a candidate for full membership in 1999 and negotiations were started in 2005 its membership bid has become and still is a major controversy in the ongoing enlargement process. This controversy contributes not only to the valuation of modern Turkey’s social, cultural, political but also its economic situation. Most statements are based on scenarios derived from the perspective on how Turkey’s membership would influence the EU as a whole and/or some of its member states. The development of Turkey as EU member was rarely researched. In particular it was not studied how Turkey’s membership would change Turkey and how these changes would re-influence the development of the EU in a longer run. The present financial, debt crisis in the EU led to intensified short-term oriented analyses on just financial aspects. In order to define and discuss pros and cons of Turkey’s accession it is not sufficient anymore to focus almost exclusively on the effects of Turkey’s accession to the EU. Turkey is to be analyzed from three further perspectives and scenarios: 1 How will Turkey develop as non-member state? 2 How would Turkey develop as a member-state? And 3 How would Turkey as a member state re-influence the EU? As the present economic crisis of the EU (for instance about 46 % of young people in Spain are jobless is aggravated by a major financial crisis in the Euro zone, the economic and financial perspectives of development have to be moved into focus. The “Europe 2020 Strategy” points the way, as it provides indicators to measure the EU’s development from a long-termed perspective. Growth “at EU and national levels” has to be “smart”, “sustainable” and “inclusive”. Accordingly, “five targets were identified: (1 75 % of the population aged 20-64 should be employed, (2 3% of the EU's GDP should be invested in R&D, (3 The "20/20/20" climate/energy targets should be met, (4 The share of

Control rod ejection analysis during a depressurization accident and the development of a rod-ejection-preventing device

International Nuclear Information System (INIS)

Mitake, S.; Itoh, K.; Fukushima, H.; Inoue, T.

1982-01-01

The control rods used for the experimental VHTR are suspended in the core by means of flexible steel cables and it is conceivable that an accidental rod ejection could occur due to a depressurization accident. The computer code AFLADE was developed in order to analyze the possibility of accidental rod ejection, and several studies were performed. The parametric study results showed that the adopted design condition for the VHTR core will not cause a rod ejection accident. In parallel with these accident analyses, a rod-ejection-preventing device was developed in preparation for a hypothetical accident, and its function was verified by the component tests

Investigation of control rod worth and nuclear end of life of BWR control rods

International Nuclear Information System (INIS)

Magnusson, Per

2008-01-01

This work has investigated the Control Rod Worth (CRW) and Nuclear End of Life (NEOL) values for BWR control rods. A study of how different parameters affect NEOL was performed with the transport code PHOENIX4. It was found that NEOL, expressed in terms of 10 B depletion, can be generalized beyond the conditions for which the rod is depleted, such as different power densities and void fractions, the corresponding variation in the NEOL will be about 0.2-0.4% 10 B. It was also found that NEOL results for different fuel types and different fuel enrichments have a variation of about 2-3% in 10 B depletion. A comparative study on NHOL and CRW was made between PHOENIX4 and the stochastic Monte Carlo code MCNP. It was found that there is a significant difference, both due to differences in the codes and to limitations in the geometrical modeling in PHOENIX4. Since MCNP is considered more physically correct, a methodology was developed to calculate the nuclear end of life of BWR control rods with MCNP. The advantages of the methodology are that it does not require other codes to perform the depletion of the absorber material, it can describe control rods of any design and it can deplete the control rod absorber material without burning the fuel. The disadvantage of the method is that is it time-consuming

Preliminary nuclear design for test MOX Fuel rods

Energy Technology Data Exchange (ETDEWEB)

Joo, Hyung Kook; Kim, Taek Kyum; Jeong, Hyung Guk; Noh, Jae Man; Cho, Jin Young; Kim, Young Il; Kim, Young Jin; Sohn, Dong Seong

1997-10-01

As a part of activity for future fuel development project, test MOX fuel rods are going to be loaded and irradiated in Halden reactor core as a KAERI`s joint international program with Paul Scherrer Institute (PSI). PSI will fabricate test MOX rods with attrition mill device which was developed by KAERI. The test fuel assembly rig contains three MOX rods and three inert matrix rods. One of three MOX rods will be fabricated by BNFL, the other two MOX fuel rods will be manufacturing jointly by KAERI and PSI. Three inert matrix fuel rods will be fabricated with Zr-Y-Er-Pu oxide. Neutronic evaluation was preliminarily performed for test fuel assembly suggested by PSI. The power distribution of test fuel rod in test fuel assembly was analyzed for various fuel rods position in assembly and the depletion characteristic curve for test fuel was also determined. The fuel rods position in test fuel assembly does not effect the rod power distribution, and the proposal for test fuel rods suggested by PSI is proved to be feasible. (author). 2 refs., 13 tabs., 16 figs.

Single-phase convective heat transfer in rod bundles

International Nuclear Information System (INIS)

Holloway, Mary V.; Beasley, Donald E.; Conner, Michael E.

2008-01-01

The convective heat transfer for turbulent flow through rod bundles representative of nuclear fuel rods used in pressurized water reactors is examined. The rod bundles consist of a square array of parallel rods that are held on a constant pitch by support grids spaced axially along the rod bundle. Split-vane pair support grids, which create swirling flow in the rod bundle, as well as disc and standard support grids are investigated. Single-phase convective heat transfer coefficients are measured for flow downstream of support grids in a rod bundle. The rods are heated using direct resistance heating, and a bulk axial flow of air is used to cool the rods in the rod bundle. Air is used as the working fluid instead of water to reduce the power required to heat the rod bundle. Results indicate heat transfer enhancement for up to 10 hydraulic diameters downstream of the support grids. A general correlation is developed to predict the heat transfer development downstream of support grids. In addition, circumferential variations in heat transfer coefficients result in hot streaks that develop on the rods downstream of split-vane pair support grids

Single-phase convective heat transfer in rod bundles

Energy Technology Data Exchange (ETDEWEB)

Holloway, Mary V. [Mechanical Engineering Department, United States Naval Academy, 590 Holloway Rd., Annapolis, MD 21402 (United States)], E-mail: holloway@usna.edu; Beasley, Donald E. [Mechanical Engineering Department, Clemson University, Clemson, SC 29634 (United States); Conner, Michael E. [Westinghouse Nuclear Fuel, 5801 Bluff Road, Columbia, SC 29250 (United States)

2008-04-15

The convective heat transfer for turbulent flow through rod bundles representative of nuclear fuel rods used in pressurized water reactors is examined. The rod bundles consist of a square array of parallel rods that are held on a constant pitch by support grids spaced axially along the rod bundle. Split-vane pair support grids, which create swirling flow in the rod bundle, as well as disc and standard support grids are investigated. Single-phase convective heat transfer coefficients are measured for flow downstream of support grids in a rod bundle. The rods are heated using direct resistance heating, and a bulk axial flow of air is used to cool the rods in the rod bundle. Air is used as the working fluid instead of water to reduce the power required to heat the rod bundle. Results indicate heat transfer enhancement for up to 10 hydraulic diameters downstream of the support grids. A general correlation is developed to predict the heat transfer development downstream of support grids. In addition, circumferential variations in heat transfer coefficients result in hot streaks that develop on the rods downstream of split-vane pair support grids.

In-Situ Growth and Characterization of Indium Tin Oxide Nanocrystal Rods

Directory of Open Access Journals (Sweden)

Yan Shen

2017-11-01

Full Text Available Indium tin oxide (ITO nanocrystal rods were synthesized in-situ by a vapor-liquid-solid (VLS method and electron beam evaporation technique. When the electron-beam gun bombarded indium oxide (In2O3 and tin oxide (SnO2 mixed sources, indium and tin droplets appeared and acted as catalysts. The nanocrystal rods were in-situ grown on the basis of the metal catalyst point. The nanorods have a single crystal structure. Its structure was confirmed by X-ray diffraction (XRD and transmission electron microscopy (TEM. The surface morphology was analyzed by scanning electron microscopy (SEM. During the evaporation, a chemical process was happened and an In2O3 and SnO2 solid solution was formed. The percentage of doped tin oxide was calculated by Vegard’s law to be 3.18%, which was in agreement with the mixture ratio of the experimental data. The single crystal rod had good semiconductor switch property and its threshold voltage of single rod was approximately 2.5 V which can be used as a micro switch device. The transmission rate of crystalline nanorods ITO film was over 90% in visible band and it was up to 95% in the blue green band as a result of the oxygen vacancy recombination luminescence.

Fabrication of internally instrumented reactor fuel rods

International Nuclear Information System (INIS)

Schmutz, J.D.; Meservey, R.H.

1975-01-01

Procedures are outlined for fabricating internally instrumented reactor fuel rods while maintaining the original quality assurance level of the rods. Instrumented fuel rods described contain fuel centerline thermocouples, ultrasonic thermometers, and pressure tubes for internal rod gas pressure measurements. Descriptions of the thermocouples and ultrasonic thermometers are also contained

Vibrational characteristics and wear of fuel rods

International Nuclear Information System (INIS)

Schmugar, K.L.

1977-01-01

Fuel rod wear, due to vibration, is a continuing concern in the design of liquid-cooled reactors. In my report, the methodology and models that are used to predict fuel rod vibrational response and vibratory wear, in a light water reactor environment, are discussed. This methodology is being followed at present in the design of Westinghouse Nuclear Fuel. Fuel rod vibrations are expressed as the normal bending modes, and sources of rod vibration are examined with special emphasis on flow-induced mechanisms in the stable flow region. In a typical Westinghouse PWR fuel assembly design, each fuel rod is supported at multiple locations along the rod axis by a square-shaped 'grid cell'. For a fuel rod /grid support system, the development of small oscillatory motions, due to fluid flow at the rod/grid interface, results in material wear. A theoretical wear mode is developed using the Archard Theory of Adhesive Wear as the basis. Without question certainty, fretting wear becomes a serious problem if it progresses to the stage where the fuel cladding is penetrated and fuel is exposed to the coolant. Westinghouse fuel is designed to minimize fretting wear by limiting the relative motion between the fuel rod and its supports. The wear producing motion between the fuel rod and its supports occurs when the vibration amplitude exceeds the slippage threshold amplitude

KfK-analysis of the SUPER-PHENIX-1 control rod experiments. Pt. 2

International Nuclear Information System (INIS)

Giese, H.

1992-10-01

Using standard data and codes, this first analysis campaign led to results that drastically overestimated measured control rod worths with C/E ratios ranging from 1.17 to 1.28. These findings were in sharp contrast to the results of the majority of earlier control rod experiments in zero-power facilities, where C/E ratios were usually comprised between 1.0 and 1.1. Investigations were then launched to identify the origin of this discrepancy. By comparison with the calculation methods employed by the other working groups engaging in the analysis of the SPX-1 experiments it was found that the principal problem arose from the KfK/BN-procedure used for the homogenization of control rod absorber cross sections. The specific failure of this standard procedure in the case of the SPX-1 analysis is ascribed to the extremely heterogeneous structure of the SPX-1 control rods. In an attempt to improve on this point, a new method for the production of homogenized absorber cross sections was developed and applied to the SPX-1 analysis. The report concludes with a description of this method and a survey of the results obtained for SPX-1. It is found that this revised analysis leads to a significantly improved agreement of measured and calculated control rod worths and to a better consistency with the results of earlier control rod experiments in zero-power facilities. (orig.)

Wind energy and Turkey.

Science.gov (United States)

Coskun, Aynur Aydin; Türker, Yavuz Özhan

2012-03-01

The global energy requirement for sustaining economic activities, meeting social needs and social development is increasing daily. Environmentally friendly, renewable energy resources are an alternative to the primary non-renewable energy resources, which devastate ecosystems in order to meet increasing demand. Among renewable energy sources such as hydropower, biopower, geothermal power and solar power, wind power offers distinct advantages to Turkey. There is an increasing tendency toward wind globally and the European Union adjusted its legal regulations in this regard. As a potential EU Member state, Turkey is going through a similar process. The number of institutional and legal regulations concerning wind power has increased in recent years; technical infrastructure studies were completed, and some important steps were taken in this regard. This study examines the way in which Turkey has developed support for wind power, presents a SWOT analysis of the wind power sector in Turkey and a projection was made for the concrete success expected to be accomplished in the future.

Distance Education in Turkey

Directory of Open Access Journals (Sweden)

Dr. Nursel Selver RUZGAR,

2004-04-01

Full Text Available Distance Education in Turkey Assistant Professor Dr. Nursel Selver RUZGAR Technical Education Faculty Marmara University, TURKEY ABSTRACT Many countries of the world are using distance education with various ways, by internet, by post and by TV. In this work, development of distance education in Turkey has been presented from the beginning. After discussing types and applications for different levels of distance education in Turkey, the distance education was given in the cultural aspect of the view. Then, in order to create the tendencies and thoughts of graduates of Higher Education Institutions and Distance Education Institutions about being competitors in job markets, sufficiency of education level, advantages for education system, continuing education in different Institutions, a face-to-face survey was applied to 1284 graduates, 958 from Higher Education Institutions and 326 from Distance Education Institutions. The results were evaluated and discussed. In the last part of this work, suggestions to become widespread and improve the distance education in the country were made.

Drive-in device for long thin rods into narrow cavitations, especially for control-shutdown rods e.g. of nuclear reactors

International Nuclear Information System (INIS)

Flessner, H.; Paeserack, U.

1974-01-01

The auxiliary device serves as holder for long and thin rods, e.g. control rods, transported hanging in bundles, when these are lowered into narrow cavities. It is constructed as a rod grab vertically movable at the end of a guide tube. A comb-shaped trap in connection with a guide rod serves for lateral support of the lower ends of the rods hanging on the grab. This guide rod can be moved in vertical direction by means of two pairs of convex rollers resting on the inner guide tube. In addition, the guide rod has a prolongation carrying a traverse by means of an abutment on the lower end. With these auxiliaries amongst others, the trap can be brought into a horizontal position by turning around an axis with the control rods meshing with the teeth of the trap while the parallelism of the rods is kept up during transport. (DG) [de

Control rod excess withdrawal prevention device

International Nuclear Information System (INIS)

Takayama, Yoshihito.

1992-01-01

Excess withdrawal of a control rod of a BWR type reactor is prevented. That is, the device comprises (1) a speed detector for detecting the driving speed of a control rod, (2) a judging circuit for outputting an abnormal signal if the driving speed is greater than a predetermined level and (3) a direction control valve compulsory closing circuit for controlling the driving direction of inserting and withdrawing a control rod based on an abnormal signal. With such a constitution, when the with drawing speed of a control rod is greater than a predetermined level, it is detected by the speed detector and the judging circuit. Then, all of the direction control valve are closed by way of the direction control valve compulsory closing circuit. As a result, the operation of the control rod is stopped compulsorily and the withdrawing speed of the control rod can be lowered to a speed corresponding to that upon gravitational withdrawal. Accordingly, excess withdrawal can be prevented. (I.S)

Hollow rods for the oil producing industry

Energy Technology Data Exchange (ETDEWEB)

Khalimova, L M; Elyasheva, M A

1970-01-01

Hollow sucker rods have several advantages over conventional ones. The hollow rods actuate the well pump and at the same time conduct produced fluids to surface. When paraffin deposition occurs, it can be minimized by injecting steam, hot oil or hot water into the hollow rod. Other chemicals, such as demulsifiers, scale inhibitors, corrosion inhibitors, etc., can also be placed in the well through the hollow rods. This reduces cost of preventive treatments, reduces number of workovers, increases oil production, and reduces cost of oil. Because the internal area of the rod is small, the passing liquids have a high velocity and thereby carry sand and dirt out of the well. This reduces pump wear between the piston and the plunger. Specifications of hollow rods, their operating characteristics, and results obtained with such rods under various circumstances are described.

ELECTRIC FIELD MEASUREMENT IN ROD-DISCONTINUED ...

African Journals Online (AJOL)

2014-06-30

Jun 30, 2014 ... the electrogeometrical model using a laboratory experimental rod-plane air gap arrangement with a lightning conductor (Franklin rod or horizontal conductor). The stepped leader could be represented by the rod electrode under a negative lightning impulse voltage having a level leading to breakdown with ...

Method of inspecting control rod drive mechanism

International Nuclear Information System (INIS)

Sato, Tomomi; Tatemichi, Shin-ichiro; Hasegawa, Hidenobu.

1988-01-01

Purpose: To conduct inspection for control rod drives and fuel handling operations in parallel without taking out the entire fuel, while maintaining the reactor in a subcritical state. Method: Control rod drives are inspected through the release of connection between control rods and control rod drives, detachment and dismantling of control rod drives, etc. In this case, structural materials having neutron absorbing power equal to or greater than the control rods are inserted into the gap after taking out fuels. Since the structural materials have neutron absorbing portion, subcriticality is maintained by the neutron absorbing effect. Accordingly, there is no requirement for taking out all of the fuels, thereby enabling to check the control rod drives and conduct handling for the fuels in parallel. As a result, the number of days required for the inspection can be shortened and it is possible to improve the working efficiency for the decomposition, inspection, etc. of the control rod drives and, thus, improve the operation efficiency of the nuclear power plant thereby attaining the predetermined purpose. (Kawakami, Y.)

British American Tobacco's failure in Turkey.

Science.gov (United States)

Lawrence, S

2009-02-01

Transnational tobacco companies (TTCs) considered Turkey an important, potential investment market because of its high consumption rates and domestic commitment to tobacco. This paper outlines how British American Tobacco (BAT) attempted to establish a joint venture with the government monopoly TEKEL, while waiting for privatisation and a private tender. Analysis of tobacco industry documents from the Guildford Depository and online tobacco document sources. BAT failed to establish a market share in Turkey until 2000 despite repeated attempts to form a joint venture with Turkey's tobacco monopoly, TEKEL, once the market liberalised in the mid 1980s. BAT's failure in the Turkish market was due to a misguided investment strategy focused solely on acquiring TEKEL and is contrasted with Philip Morris success in Turkey despite both TTCs working within Turkey's unstable and corrupt investing climate.

Control rod

International Nuclear Information System (INIS)

Takeda, Toshikazu; Inoue, Kotaro.

1979-01-01

Purpose: To flatten the power distribution in the reactor core without impairing neutron economy by disposing pins containing elements of lower atomic number in the central region of a shroud and loading pins containing depleted uranium in the periphery region thereof. Constitution: The shroud has a layer of pins containing depleted uranium in the peripheral region and a layer of pins containing elements of lower atomic number such as beryllium in the central region. Heat removal from those pins containing depleted uranium and elements of lower atomic number (neutron moderator) is effected by sodium flow outside of the cladding material. The control rod operation is conducted by inserting or extracting the central portion (pins containing elements of lower atomic number such as beryllium) inside of the stainless pipe. Upon extraction of the control rod, the moderator in the central region is removed whereby high speed neutrons are no more deccelerated and the absorption rate to the depleted uranium is decreased. This can flatten the power distribution in the reactore core with the disposition of a plurality of control rods at a better neutron economy as compared with the use of neutron absorber such as boron. (Seki, T.)

Control rod

International Nuclear Information System (INIS)

Fukumoto, Takashi; Hirakawa, Hiromasa; Kawashima, Norio; Goto, Yasuyuki.

1994-01-01

Neutron absorbers are contained in a tubular member comprising, integrally a tubular portion and four corners disposed at the outer circumference of the tubular portion at every 90deg, to provide a neutron absorbing tube. A plurality of neutron absorbing tubes are arranged in parallel in the lateral direction, and adjacent corners are joined, into a blade to constitute a control rod. Such a control rod has a great structural strength, simple in the structure and relatively light in weight and can contain a great amount of neutron absorbers. Upon formation of the control rod by arranging the blades in a cross-like shape, at least a portion thereof is constituted with short neutron absorbing tubes shorter than the entire length of the blade, and gaps are formed at positions in adjacent in the axial direction. With such a constitution, there is no worry that a wing end of the blade collides against or be abraded with a fuel channel box or a fuel support. Even if fuel channels are vibrated upon scram of the reactor, such as occurrence of earthquakes, it can be inserted to the reactor easily. (N.H.)

Practical application of food irradiation in Turkey

International Nuclear Information System (INIS)

Cetinkaya, N.; Erhan, I.C.

2002-01-01

Turkey is the world's leading producer and exporter of dried fruits (dried figs, raisins,and dried apricots etc.) and nuts (hazelnuts, wall nuts, pistachios, peanuts etc.) all of which have to be fumigated by methyl bromide a few times prior to export. Last fumigation is obligatory before shipment according to current quarantine treatment. Methyl Bromide (MeBr) fumigation is the most commonly used insect quarantine treatment for dried fruits and nuts in Turkey to protect from potential infestations. In accordance with the Montreal Protocol, Turkey as an Article 5(1) country will take actions to regulate and take measures to phase-out MeBr use. So, Turkey has to total phase-out in 2015 but according to Turkey MeBr Phase-out Action Plan prepared and published by The Ministry of Agriculture and Rural affairs in 2001, using MeBr should be reduced for stored commodities by 50 % by 2002 and phased-out totally by 2004. Irradiation technology is ready as an alternative to MeBr fumigation under the Action Plan of Turkey. Intensive research studies on food irradiation in Turkey have started in early 1970's and have still been continued. After careful and intensive works of all related authorities and specialists for a long period and with the help of ICGFI, the food irradiation regulation of Turkey was published in Official Newspaper on November 6, 1999. Having the Food Irradiation Regulation has supported to initiate commercialization study in Turkey in Co-operation with IAEA (TUR 5022). Feasibility study of a commercial food irradiation facility for the potential application of food irradiation in Turkey was prepared by IAEA experts Dr.M.Ahmed and Ir. J.P.Lacroix and together with TUR 5022 Research Team in April 2001 in Izmir, Turkey. Gamma-Pak Irradiation Facility in Cerkeskoy-Tekirdag got the commercial food irradiation licence and registration certificate in Feb. 2002. Practical application of food irradiation is getting more attraction in Turkey in parallel with other

Enhanced thermal expansion control rod drive lines for improving passive safety of fast reactors

International Nuclear Information System (INIS)

Edelmann, M.; Baumann, W.; Kuechle, M.; Kussmaul, G.; Vaeth, W.; Bertram, A.

1992-01-01

The paper presents a device for increasing the thermal expansion effect of control rod drive lines on negative reactivity feedback in fast reactors. The enhanced thermal expansion of this device can be utilized for both passive rod drop and forced insertion of absorbers in unprotected transients, e.g. ULOF. In this way the reactor is automatically brought into a permanently subcritical state and temperatures are kept well below the boiling point of the coolant. A prototype of such a device called ATHENa (German: Shut-down by THermal Expansion of Na) is presently under construction and will be tested. The paper presents the principle, design features and thermal properties of ATHENs as well as results of reactor dynamics calculations of ULOF's for EFR with enhanced thermal expansion control rod drive lines. (author)

Experimental determination of temperature fields in sodium-cooled rod bundles with hexagonal rod arrangement and grid spacers

International Nuclear Information System (INIS)

Moeller, R.; Tschoeke, H.; Kolodziej, M.

1977-01-01

Three-dimensional temperature fields in the claddings of sodium cooled rods were determined experimentally under representative nominal operating conditions for a SNR typical 19-rod bundle model provided with spark-eroded spacers. These experiments are required to verify thermohydraulic computer programs which will provide the output data for strength calculations of the high loaded cladding tubes. In this work the essentials are reported of the measured circumferential distributions of wall temperatures of peripheral rods. In addition the sub-channel temperatures measured over the bundle cross section are indicated, they are required to sustain codes for the global thermohydraulic design of core elements. The most important results are: 1) The whole fuel element is located within the thermal entrance length. 2) High azimuthal temperature differences were measured in the claddings of peripheral rods, which are strongly influenced by the distance between the rod and the shroud, especially for the corner rod. 3) With decreasing Pe-number ( [de

Control rod housing alignment

International Nuclear Information System (INIS)

Dixon, R.C.; Deaver, G.A.; Punches, J.R.; Singleton, G.E.; Erbes, J.G.; Offer, H.P.

1990-01-01

This patent describes a process for measuring the vertical alignment between a hole in a core plate and the top of a corresponding control rod drive housing within a boiling water reactor. It comprises: providing an alignment apparatus. The alignment apparatus including a lower end for fitting to the top of the control rod drive housing; an upper end for fitting to the aperture in the core plate, and a leveling means attached to the alignment apparatus to read out the difference in angularity with respect to gravity, and alignment pin registering means for registering to the alignment pin on the core plate; lowering the alignment device on a depending support through a lattice position in the top guide through the hole in the core plate down into registered contact with the top of the control rod drive housing; registering the upper end to the sides of the hole in the core plate; registering the alignment pin registering means to an alignment pin on the core plate to impart to the alignment device the required angularity; and reading out the angle of the control rod drive housing with respect to the hole in the core plate through the leveling devices whereby the angularity of the top of the control rod drive housing with respect to the hole in the core plate can be determined

Petroleum Gases Market in Turkey

International Nuclear Information System (INIS)

Bumin, S.; Ozyoruk, B.

2007-01-01

We are at the beginning of a new millennium. At this stage, we are observing economic and social liberalization efforts and regional alliance projects throughout the world. In this very same process, we are also experiencing a more holistic concept called globalization, which covers rapid and simultaneous dissemination and integration of capital, labor, information and technology, world-wide. This globalization opened a new era where national market economies and local companies went into competition in the international arena. In this era, it became a necessity for the non-liberal economies to catch up with the developments in the international markets and be open to economic and political changes. These developments have brought along many radical economic and social changes throughout the world. Policies adopted in Turkey, with respect to the energy reform process, display a general tendency towards putting in place a legal framework that will support the implementation of good governance principles, and providing conformity with the relevant legislative infrastructure of both OECD and EU countries. Turkey has only limited reserves of oil and natural gas, but substantial reserves of coal, particularly lignite. Energy demand has grown at 4-5 % per annum over the past three decades and will continue to grow rapidly, which will require enormous investments in 2000 and 2020, with the most significant increase being that of natural gas. Because of its limited energy resources, Turkey is heavily dependent on imported oil and gas. There are major oil and gas pipelines going through Turkey and additional pipelines are being constructed or are being planned. There is some production of lignite which is used in power plants and industry. 73 % of the world's proven oil reserves and 72 % of the world's proven gas reserves are located in the surrounding regions of Turkey: Middle East, Caspian Region and Russia. This makes Turkey a crucial bridge between energy rich regions

Sensitivity studies for 3-D rod ejection analyses on axial power shape

Energy Technology Data Exchange (ETDEWEB)

Park, Min-Ho; Park, Jin-Woo; Park, Guen-Tae; Ryu, Seok-Hee; Um, Kil-Sup; Lee, Jae-Il [KEPCO NF, Daejeon (Korea, Republic of)

2015-10-15

The current safety analysis methodology using the point kinetics model combined with numerous conservative assumptions result in unrealistic prediction of the transient behavior wasting huge margin for safety analyses while the safety regulation criteria for the reactivity initiated accident are going strict. To deal with this, KNF is developing a 3-D rod ejection analysis methodology using the multi-dimensional code coupling system CHASER. The CHASER system couples three-dimensional core neutron kinetics code ASTRA, sub-channel analysis code THALES, and fuel performance analysis code FROST using message passing interface (MPI). A sensitivity study for 3-D rod ejection analysis on axial power shape (APS) is carried out to survey the tendency of safety parameters by power distributions and to build up a realistic safety analysis methodology while maintaining conservatism. The currently developing 3-D rod ejection analysis methodology using the multi-dimensional core transient analysis code system, CHASER was shown to reasonably reflect the conservative assumptions by tuning up kinetic parameters.

The Third ATLAS ROD Workshop

CERN Multimedia

Poggioli, L.

A new-style Workshop After two successful ATLAS ROD Workshops dedicated to the ROD hardware and held at the Geneva University in 1998 and in 2000, a new style Workshop took place at LAPP in Annecy on November 14-15, 2002. This time the Workshop was fully dedicated to the ROD-TDAQ integration and software in view of the near future integration activities of the final RODs for the detector assembly and commissioning. More precisely, the aim of this workshop was to get from the sub-detectors the parameters needed for T-DAQ, as well as status and plans from ROD builders. On the other hand, what was decided and assumed had to be stated (like EB decisions and URDs), and also support plans. The Workshop gathered about 70 participants from all ATLAS sub-detectors and the T-DAQ community. The quite dense agenda allowed nevertheless for many lively discussions, and for a dinner in the old town of Annecy. The Sessions The Workshop was organized in five main sessions: Assumptions and recommendations Sub-de...

Parallel diffusion length on thermal neutrons in rod type lattices

International Nuclear Information System (INIS)

Ahmed, T.; Siddiqui, S.A.M.M.; Khan, A.M.

1981-11-01

Calculation of diffusion lengths of thermal neutrons in lead-water and aluminum water lattices in direction parallel to the rods are performed using one group diffusion equation together with Shevelev transport correction. The formalism is then applied to two practical cases, the Kawasaki (Hitachi) and the Douglas point (Candu) reactor lattices. Our results are in good agreement with the observed values. (author)

Possibilities and limits of the reactivity determination of control rods

International Nuclear Information System (INIS)

Buenemann, D.

1975-01-01

Basic physical facts of the reactivity determination of control rods are presented. A survey of currrently applied methods is given, and the drawbacks of the various methods are pointed out. Special problems are presented by the interpretation of highly subcritical assemblies which are not really important in practical reactor operation but desirable for a consistant comparison between theory and experiments. (orig./AK) [de

Temperature actuated automatic safety rod release

Science.gov (United States)

Hutter, E.; Pardini, J.A.; Walker, D.E.

1984-03-13

A temperature-actuated apparatus is disclosed for releasably supporting a safety rod in a nuclear reactor, comprising a safety rod upper adapter having a retention means, a drive shaft which houses the upper adapter, and a bimetallic means supported within the drive shaft and having at least one ledge which engages a retention means of the safety rod upper adapter. A pre-determined increase in temperature causes the bimetallic means to deform so that the ledge disengages from the retention means, whereby the bimetallic means releases the safety rod into the core of the reactor.

Shielding device for control rod in nuclear reactor

International Nuclear Information System (INIS)

Sakamaki, Kazuo; Tomatsu, Tsutomu.

1995-01-01

The device of the present invention shields radiation emitted from control rods to greatly reduce an operator's radiation exposure even if reactor water level is lowered and the upper portion of the control rod is exposed upon inspection of a BWR type reactor. Namely, a shield assembly has a structure comprising a set of four columnar shields in a two-row and two-column arrangement, which can be inserted into a control rod guide tube. Upon conducting inspection, the control rod is lowered into the control rod guide tube, and in this state, the columnar shields of the shield assembly are inserted to the control rod in the control rod guide tube. With such procedures, the upper portion of the control rod protruded from the control rod guide tube is covered with the shield assembly. As a result, radiation leaked from the control rod is shielded. Accordingly, irradiation in the reactor due to leaked radiation can be prevented thereby enabling to reduce an operator's radiation exposure. (I.S.)

Burnable poison rod

International Nuclear Information System (INIS)

Natsume, Tomohiro.

1988-01-01

Purpose: To increase the reactor core lifetime by decreasing the effect of neutron absorption of burnable poison rods by using material with less neutron absorbing effect. Constitution: Stainless steels used so far as the coating material for burnable poison rods have relatively great absorption in the thermal neutral region and are not preferred in view of the neutron economy. Burnable poison rods having fuel can made of zirconium alloy shows absorption the thermal neutron region lower by one digit than that of stainless steels but they shows absorption in the resonance region and the cost is higher. In view of the above, the fuel can of the burnable poison material is made of aluminum or aluminu alloy. This can reduce the neutron absorbing effect by stainless steel fuel can and effectively utilize neutrons that have been wastefully absorbed and consumed in stainless steels. (Takahashi, M.)

Elliptical cross section fuel rod study II; Estudio de barras combustibles de seccion eliptica II

Energy Technology Data Exchange (ETDEWEB)

Taboada, H; Marajofsky, A [Comision Nacional de Energia Atomica, San Martin (Argentina). Unidad de Actividad Combustibles Nucleares

1997-12-31

In this paper it is continued the behavior analysis and comparison between cylindrical fuel rods of circular and elliptical cross sections. Taking into account the accepted models in the literature, the fission gas swelling and release were studied. An analytical comparison between both kinds of rod reveals a sensible gas release reduction in the elliptical case, a 50% swelling reduction due to intragranular bubble coalescence mechanism and an important swelling increase due to migration bubble mechanism. From the safety operation point of view, for the same linear power, an elliptical cross section rod is favored by lower central temperatures, lower gas release rates, greater gas store in ceramic matrix and lower stored energy rates. (author). 6 refs., 8 figs., 1 tab.

Design of diverse safety rod and its drive mechanism of PFBR

International Nuclear Information System (INIS)

Vijayashree, R.; Govindarajan, S.; Chetal, S.C.

1997-01-01

In Prototype Fast Breeder Reactor (PFBR), there are two types of absorber rods for control and shutdown of the reactor in the event of any abnormal event. They are: (i) Control and Safety Rod (CSR) and (ii) the Diverse Safety Rod (DSR). Of these, the former (CSR) caters to the control function of the reactor during normal operating conditions and to the shutdown during abnormal situations. The DSR, on the other hand is meant essentially for the reactor shutdown to take care of any abnormal transient. It is rather important to note that functionally the DSR is independent of CSR in the sense, that it can bring the reactor to a cold shutdown state and maintain it even under the hypothetical condition of the failure of CSR. From the design point of view, this stipulates a failure probability of less than 10 -4 per demand. The DSR is normally parked above the core by the Diverse Safety Rod Drive Mechanism (DSRDM). On receiving a scram signal it gets released from the holding electromagnet and falls under the gravity into the core. Diverse features are incorporated both in the absorber rods and in the drive mechanisms to avoid common mode failures. This paper discusses the salient features of DSR and DSRDM. A brief account of detailed design, analysis and development of two important subassemblies viz. electromagnet and sodium dash pot is also presented. In addition, a brief comparison between CSR and DSR including their drive mechanisms is also provided. (author)

Simulation of leaking fuel rods

International Nuclear Information System (INIS)

Hozer, Z.

2006-01-01

The behaviour of failed fuel rods includes several complex phenomena. The cladding failure initiates the release of fission product from the fuel and in case of large defect even urania grains can be released into the coolant. In steady state conditions an equilibrium - diffusion type - release is expected. During transients the release is driven by a convective type leaching mechanism. There are very few experimental data on leaking WWER fuel rods. For this reason the activity measurements at the nuclear power plants provide very important information. The evaluation of measured data can help in the estimation of failed fuel rod characteristics and the prediction of transient release dynamics in power plant transients. The paper deals with the simulation of leaking fuel rods under steady state and transient conditions and describes the following new results: 1) A new algorithm has been developed for the simulation of leaking fuel rods under steady state conditions and the specific parameters of the model for the Paks NPP has been determined; 2) The steady state model has been applied to calculation of leaking fuel characteristics using iodine and noble gas activity measurement data; 3) A new computational method has been developed for the simulation of leaking fuel rods under transient conditions and the specific parameters for the Paks NPP has been determined; 4) The transient model has been applied to the simulation of shutdown process at the Paks NPP and for the prediction of the time and magnitude of 123 I activity peak; 5) Using Paks NPP data a conservative value has been determined for the upper limit of the 123 I release from failed fuel rods during transients

Control rod for HTGR type reactor

International Nuclear Information System (INIS)

Mogi, Haruyoshi; Saito, Yuji; Fukamichi, Kenjiro.

1990-01-01

Upon dropping control rod elements into the reactor core, impact shocks are applied to wire ropes or spines to possibly deteriorate the integrity of the control rods. In view of the above in the present invention, shock absorbers such as springs or bellows are disposed between a wire rope and a spine in a HTGR type reactor control rod comprising a plurality of control rod elements connected axially by means of a spine that penetrates the central portion thereof, and is suspended at the upper end thereof by a wire rope. Impact shocks of about 5 kg are applied to the wire rope and the spine and, since they can be reduced by the shock absorbers, the control rod integrity can be maintained and the reactor safety can be improved. (T.M.)

Why Rods and Cocci

Indian Academy of Sciences (India)

Bacteria exhibit a wide variety of shapes but the commonly studied species of bacteria are generally either spherical in shape which are called cocci (singular coccus) or have a cylindrical shape and are called rods or bacilli (singular bacillus). In reality rods and cocci are the ends of a continuum. Sonle of the cocci are.

Spacers for fuel rod clusters

International Nuclear Information System (INIS)

Jabsen, F.S.

1978-01-01

The proposition deals with the fixing of nuclear fuel element rods in a grid which consists of a number of crossed Zy-plates which form cells. The rectangular cells have projections which serve as spacers for the fuel rods. According to the invention there are additional butt straps which can be moved in such a way that insertion and extraction of the fuel rods can be done without obstruction and they can be spring-loaded hold in their final position. (UWI) [de

Rod consolidation at the West Valley Demonstration Project

International Nuclear Information System (INIS)

Bailey, W.J.

1986-12-01

A rod consolidation demonstration with irradiated pressurized water reactor fuel was recently conducted by personnel from Nuclear Assurance Corporation and West Valley Nuclear Services Company at the West Valley Demonstration Project in West Valley, New York. The rod consolidation demonstration involved pulling all of the fuel rods from six fuel Assemblies. In general, the rod pulling proceeded smoothly. The highest compaction ratio attained was 1:8:1. Among the total of 1074 fuel rods were some known degraded rods (they had collapsed cladding, a result of in-reactor fuel densification), but no rods were broken or dropped during the demonstration. One aim was to gather information on the effect of rod consolidation operations on the integrity of the fuel rods during subsequent handling and storage. Another goal was to collect information on the condition and handling of intact, damaged, and failed fuel that has been in storage for an extended period. 9 refs., 8 figs., 1 tab

21 CFR 876.4270 - Colostomy rod.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Colostomy rod. 876.4270 Section 876.4270 Food and... GASTROENTEROLOGY-UROLOGY DEVICES Surgical Devices § 876.4270 Colostomy rod. (a) Identification. A colostomy rod is a device used during the loop colostomy procedure. A loop of colon is surgically brought out through...

Control rod effects with plutonium recycle in a PWR

International Nuclear Information System (INIS)

Nash, G.; Muehl, G.J.; Gibson, I.H.

1979-03-01

A study has been made on a PWR loaded partly and wholly with plutonium to determine the changes in shutdown margin compared with an enriched uranium core. Lattice calculations are used to generate cell constants for core calculations. Three fuel loadings were considered, all uranium, 30% (approximately) of the assemblies plutonium in natural uranium, and all plutonium. The equilibrium fuel management schemes adopted in each case are based on the standard three cycle equal size batch scheme. Detailed calculations of power and irradiation distributions through the cycles have been carried out to provide a starting point for the control rod worth and requirement calculations. Control rod worths are reduced in a plutonium core because of the harder spectrum and higher fuel absorption cross sections. Furthermore, the control rod requirements for shutdown increase because of the increase in fuel and moderator temperature coefficients. This results in a reduction in shutdown margin. The magnitude of these changes is fully analysed in the report. The significance of these reductions depends on the detail of the safety argument but reductions of these sizes are unlikely to be acceptable. The data provided in this report could be used to give a first estimate of the plutonium loading acceptable given the safety assessment of the normal uranium core. (U.K.)

New Westinghouse correlation WRB-1 for predicting critical heat flux in rod bundles with mixing vane grids

International Nuclear Information System (INIS)

Motley, F.E.; Hill, K.W.; Cadek, F.F.; Shefcheck, J.

1976-07-01

A new critical heat flux (CHF) correlation, based on local fluid conditions, has been developed from Westinghouse rod bundle data. This correlation applies to both 0.422 inch and 0.374 inch rod O.D. geometries. It accounts for typical cell and thimble cell effects, uniform and non-uniform heat flux profiles, variations in rod heated length and in grid spacing. The correlation predicts CHF for 1147 data points with a sample mean and standard deviation of measured-to-predicted heat flux ratio of 1.0043 and 0.0873, respectively. It was concluded that to meet the reactor design criterion the minimum DNBR should be 1.17

Control rod for FBR type reactor

International Nuclear Information System (INIS)

Nakai, Koichi.

1993-01-01

In a control rod for an LMFBR type reactor, a thermal resistor is disposed between a temperature sensitive cylinder and a cam unit support rod. A thermal expansion difference due to the temperature difference is caused between the temperature sensitive cylinder and the cam unit support rod only upon abrupt temperature change of coolants. A control rod shaft extending mechanism of downwardly depressing an absorbent portion by amplifying the thermal expansion difference by an extension link mechanism and the cam unit is provided. The thermal resistor comprises inconel 625 or like other steel of small heat conductivity. If a certain abnormality should cause to the reactor system to elevate the coolant temperature in the reactor elevates abruptly and the reactor shutdown system does not actuate, since the control rod extension shaft extends to urge the absorbent and lower the reactor core reactivity, so that leading to serious accident can be prevented surely. Further, the control rod extension shaft does not extend upon moderate temperature elevation in the usual startup and causes no unnecessary reactivity change. (N.H.)

Design of active-neutron fuel rod scanner

International Nuclear Information System (INIS)

Griffith, G.W.; Menlove, H.O.

1996-01-01

An active-neutron fuel rod scanner has been designed for the assay of fissile materials in mixed oxide fuel rods. A 252 Cf source is located at the center of the scanner very near the through hole for the fuel rods. Spontaneous fission neutrons from the californium are moderated and induce fissions within the passing fuel rod. The rod continues past a combined gamma-ray and neutron shield where delayed gamma rays above 1 MeV are detected. We used the Monte Carlo code MCNP to design the scanner and review optimum materials and geometries. An inhomogeneous beryllium, graphite, and polyethylene moderator has been designed that uses source neutrons much more efficiently than assay systems using polyethylene moderators. Layers of borated polyethylene and tungsten are used to shield the detectors. Large NaI(Tl) detectors were selected to measure the delayed gamma rays. The enrichment zones of a thermal reactor fuel pin could be measured to within 1% counting statistics for practical rod speeds. Applications of the rod scanner include accountability of fissile material for safeguards applications, quality control of the fissile content in a fuel rod, and the verification of reactivity potential for mixed oxide fuels. (orig.)

Hydraulically centered control rod

International Nuclear Information System (INIS)

Horlacher, W.R.; Sampson, W.T.; Schukei, G.E.

1981-01-01

A control rod suspended to reciprocate in a guide tube of a nuclear fuel assembly has a hydraulic bearing formed at its lower tip. The bearing includes a plurality of discrete pockets on its outer surface into which a flow of liquid is continuously provided. In one embodiment the flow is induced by the pressure head in a downward facing chamber at the end of the bearing. In another embodiment the flow originates outside the guide tube. In both embodiments the flow into the pockets produces pressure differences across the bearing which counteract forces tending to drive the rod against the guide tube wall. Thus contact of the rod against the guide tube is avoided

STRUCTURAL VULNERABILITY ASSESSMENT OF MASONRY BUILDINGS IN TURKEY

OpenAIRE

KORKMAZ, Kasım Armagan; CARHOGLU, Asuman Isıl

2011-01-01

Turkey is located in an active seismic zone. Mid to high rise R/C building and low rise masonry buildings are very common construction type in Turkey. In recent earthquakes, lots of existing buildings got damage including masonry buildings. Masonry building history in Turkey goes long years back. For sure, it is an important structure type for Turkey. Therefore, earthquake behavior and structural vulnerability of masonry buildings are crucial issues for Turkey as a earthquake prone country. I...

Spider and burnable poison rod combinations

International Nuclear Information System (INIS)

Edwards, G.T.; Schluderberg, D.C.

1980-01-01

An improved design of burnable poison rods and associated spiders used in fuel assemblies of pressurized water power reactor cores, is described. The rods are joined to the spider arms in a manner which is proof against the reactor core environment and yet allows the removal of the rods from the spider simply, swiftly and delicately. (U.K.)

Calculation of Equivalent Resistance for Ground Wires Twined with Armor Rods in Contact Terminals

Directory of Open Access Journals (Sweden)

Gang Liu

2018-03-01

Full Text Available Ground wire breakage accidents can destroy the stable operation of overhead lines. The excessive temperature increase arising from the contact resistance between the ground wire and armor rod in the contact terminal is one of the main reasons causing the breakage of ground wires. Therefore, it is necessary to calculate the equivalent resistance for ground wires twined with armor rods in contact terminals. According to the actual distribution characteristics of the contact points in the contact terminal, a three-dimensional electromagnetic field simulation model of the contact terminal was established. Based on the model, the current distribution in the contact terminal was obtained. Subsequently, the equivalent resistance of a ground wire twined with the armor rod in the contact terminal was calculated. The effects of the factors influencing the equivalent resistance were also discussed. The corresponding verification experiments were conducted on a real ground wire on a contact terminal. The measurement results of the equivalent resistance for the armor rod segment showed good agreement with the electromagnetic modeling results.

The Geopolitics of Water and Oil in Turkey

International Nuclear Information System (INIS)

2009-01-01

Throughout history, few nations have been as successful in leveraging their geographic location as Turkey. As the center of two of the most powerful civilizations of all time, the Byzantine and Ottoman Empires, Turkey was the bridge between East and West, a bustling center of trade and a strategic economic and political nexus between regions of the world. In addition to its geographic power, Turkey has historically possessed substantial water resources. Unlike many water parched areas of the Middle East, Turkey's water capacity has allowed it to grow large populations and build elaborate cities. In the modern era, Turkey once again has an opportunity to regain its historical role, as the state where today's geopolitics of energy coincides with Turkey's traditional geopolitics of water. Turkey's central location, this time not between East and West, but between producers and consumers of energy, gives it a central, geopolitical role in world affairs, both in oil and gas. Moreover, Turkey's water resources can be utilized to reinforce Turkey's strategic energy role in the region, by building a strategy of cooperation with water-poor countries from the Levant to the Arabian Peninsula. Throughout history, water and energy have been among the most fundamental resources of civilization, at the very base of Maslow's hierarchy of needs essential to fostering human growth and development for thousands of years. It is seldom appreciated how linked water and energy truly are. Producing, transferring, and supplying energy requires a significant amount of water, just as the extraction, purification, and even desalination of water requires a significant amount of energy. As both energy and water grow scarcer throughout the future, nations such as Turkey can gain considerable influence as a result of their geographic locations and natural endowments. Turkey can benefit from pipeline diplomacy, taking advantage of its geographical location to make it a crossroads of multiple

The Geopolitics of Water and Oil in Turkey

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

Throughout history, few nations have been as successful in leveraging their geographic location as Turkey. As the center of two of the most powerful civilizations of all time, the Byzantine and Ottoman Empires, Turkey was the bridge between East and West, a bustling center of trade and a strategic economic and political nexus between regions of the world. In addition to its geographic power, Turkey has historically possessed substantial water resources. Unlike many water parched areas of the Middle East, Turkey's water capacity has allowed it to grow large populations and build elaborate cities. In the modern era, Turkey once again has an opportunity to regain its historical role, as the state where today's geopolitics of energy coincides with Turkey's traditional geopolitics of water. Turkey's central location, this time not between East and West, but between producers and consumers of energy, gives it a central, geopolitical role in world affairs, both in oil and gas. Moreover, Turkey's water resources can be utilized to reinforce Turkey's strategic energy role in the region, by building a strategy of cooperation with water-poor countries from the Levant to the Arabian Peninsula. Throughout history, water and energy have been among the most fundamental resources of civilization, at the very base of Maslow's hierarchy of needs essential to fostering human growth and development for thousands of years. It is seldom appreciated how linked water and energy truly are. Producing, transferring, and supplying energy requires a significant amount of water, just as the extraction, purification, and even desalination of water requires a significant amount of energy. As both energy and water grow scarcer throughout the future, nations such as Turkey can gain considerable influence as a result of their geographic locations and natural endowments. Turkey can benefit from pipeline diplomacy, taking advantage of its geographical location to

Modeling and simulation performance of sucker rod beam pump

Energy Technology Data Exchange (ETDEWEB)

Aditsania, Annisa, E-mail: annisaaditsania@gmail.com [Department of Computational Sciences, Institut Teknologi Bandung (Indonesia); Rahmawati, Silvy Dewi, E-mail: silvyarahmawati@gmail.com; Sukarno, Pudjo, E-mail: psukarno@gmail.com [Department of Petroleum Engineering, Institut Teknologi Bandung (Indonesia); Soewono, Edy, E-mail: esoewono@math.itb.ac.id [Department of Mathematics, Institut Teknologi Bandung (Indonesia)

2015-09-30

Artificial lift is a mechanism to lift hydrocarbon, generally petroleum, from a well to surface. This is used in the case that the natural pressure from the reservoir has significantly decreased. Sucker rod beam pumping is a method of artificial lift. Sucker rod beam pump is modeled in this research as a function of geometry of the surface part, the size of sucker rod string, and fluid properties. Besides its length, sucker rod string also classified into tapered and un-tapered. At the beginning of this research, for easy modeling, the sucker rod string was assumed as un-tapered. The assumption proved non-realistic to use. Therefore, the tapered sucker rod string modeling needs building. The numerical solution of this sucker rod beam pump model is computed using finite difference method. The numerical result shows that the peak of polished rod load for sucker rod beam pump unit C-456-D-256-120, for non-tapered sucker rod string is 38504.2 lb, while for tapered rod string is 25723.3 lb. For that reason, to avoid the sucker rod string breaks due to the overload, the use of tapered sucker rod beam string is suggested in this research.

Modeling and simulation performance of sucker rod beam pump

International Nuclear Information System (INIS)

Aditsania, Annisa; Rahmawati, Silvy Dewi; Sukarno, Pudjo; Soewono, Edy

2015-01-01

Artificial lift is a mechanism to lift hydrocarbon, generally petroleum, from a well to surface. This is used in the case that the natural pressure from the reservoir has significantly decreased. Sucker rod beam pumping is a method of artificial lift. Sucker rod beam pump is modeled in this research as a function of geometry of the surface part, the size of sucker rod string, and fluid properties. Besides its length, sucker rod string also classified into tapered and un-tapered. At the beginning of this research, for easy modeling, the sucker rod string was assumed as un-tapered. The assumption proved non-realistic to use. Therefore, the tapered sucker rod string modeling needs building. The numerical solution of this sucker rod beam pump model is computed using finite difference method. The numerical result shows that the peak of polished rod load for sucker rod beam pump unit C-456-D-256-120, for non-tapered sucker rod string is 38504.2 lb, while for tapered rod string is 25723.3 lb. For that reason, to avoid the sucker rod string breaks due to the overload, the use of tapered sucker rod beam string is suggested in this research

Detection device for control rod interference

International Nuclear Information System (INIS)

Saito, Noboru.

1984-01-01

Purpose: To enable to detect the mechanical interference or friction between a control rod and a channel box automatically, simply and rapidly. Constitution: A signal from a gate circuit and a signal from a comparison mechanism are inputted into an AND circuit if a control rod has not been displaced by a predetermined distance within a prescribed time Δt after the output of an insertion or withdrawal signal for the control rod, by which a control-rod-interference signal is outputted from the AND circuit. Accordingly, the interference between the control rod and the channel box can be detected automatically, easily and rapidly. Furthermore, by properly adjusting the prescribed time Δt set by the gate circuit, the degree of the interference can also be detected, whereby the safety and the reliability of the reactor can be improved significantly. (Horiuchi, T.)

Voluntary emission trading potential of Turkey

International Nuclear Information System (INIS)

Ari, İzzet

2013-01-01

Climate change is likely to cause serious market failures, and carbon trading as a market instrument can help correct its negative impacts. The global carbon markets established to combat climate change include regulatory and voluntary markets. Turkey cannot utilise regulatory carbon markets under the Kyoto Protocol. As a result of her unique position in the UNFCCC, some offsetting projects in Turkey have benefitted only voluntary emission trading for the reduction of GHG emissions. Due to on-going climate change negotiation under the UNFCCC, it seems that Turkey will not use the current regulatory carbon markets. Thus, Turkey should promote the use of and participation in voluntary carbon markets. In this article, emission reduction potential via energy efficiency, renewable energy and solid waste management, and corresponding offsetting of credits with their estimated prices is investigated for the period between 2013 and 2020. The emission reduction potential for energy efficiency, renewable energy and solid waste management projects are estimated at 403, 312 and 356 million tons of CO 2 equivalent emissions respectively, totalling 1,071 million tons of CO 2 equivalent. The total revenue of the carbon certificates are estimated in the range of 19,775–33,386 million US Dollars for the same period. -- Highlights: •Turkey has 1,071 million tons GHG emission reduction in three sectors for 2013–2020. •Turkey can only use voluntary emission trading for reduction of GHGs. •Total revenue estimation could be between 19,775 and 33,386 million US Dollars. •Turkey's economy and emissions have been rapidly growing. •Turkey can more easily reduce its emission by using voluntary emission trading

Critical heat flux near the critical pressure in heater rod bundle cooled by R-134A fluid: Effects of unheated rods and spacer grid

International Nuclear Information System (INIS)

Chun, Se-Y.; Shin, C.W.; Hong, S. D.; Moon, S. K.

2007-01-01

A supercritical-pressure light water reactor (SCWR) is currently investigated as the next generation nuclear reactors. The SCWR, which is operated above the thermodynamic critical point of water (647 K, 22.1 MPa), have advantages over conventional light water reactors in terms of thermal efficiency as well as in compactness and simplicity. Many experimental studies have been performed on heat transfer in the boiler tubes of supercritical fossil fire power plants (FPPs). However, the thermal-hydraulic conditions of the SCWR core are different from those of the FPP boiler. In the SCWR core, the heat transfer to the cooling water occurs on the outside surface of fuel rods in rod bundle with spacers. In addition, the experimental studies in which the critical heat flux (CHF) has been carefully measured near the critical pressure have never yet been carried out, as far as we know. Therefore, we have recently conducted the CHF experiments with a vertical 5x5 heater rod bundle cooled by R- 134a fluid. The purpose of this work is to find out some novel knowledge for the CHF near the critical pressure, based on more careful experiments. The outer diameter, heated length and rod pitch of the heater rods are 9.5, 2000 and 12.85 mm, respectively. The critical power has been measured in a range of the pressure of 2.474.03 MPa (the critical pressure of R-134a is 4.059 MPa), the mass flux 502000 kg/m 2 s, and the inlet subcooling 4084 kJ/kg. For the mass fluxes of not less than 550 kg/m 2 s, the critical power decreases monotonously up to the pressure of about 3.63.8 MPa with increasing pressure, and then fall sharply at about 3.83.9 MPa as if the values of the critical power converge on zero at the critical pressure. For the low mass fluxes of 50 to 250 kg/m 2 , the sharp decreasing trend of the critical power near the critical pressure is not observed. The CHF phenomenon near the critical pressure no longer leads to an inordinate increase in the heated wall temperature such as

Earliest Mexican Turkeys (Meleagris gallopavo) in the Maya Region: implications for pre-Hispanic animal trade and the timing of turkey domestication.

Science.gov (United States)

Thornton, Erin Kennedy; Emery, Kitty F; Steadman, David W; Speller, Camilla; Matheny, Ray; Yang, Dongya

2012-01-01

Late Preclassic (300 BC-AD 100) turkey remains identified at the archaeological site of El Mirador (Petén, Guatemala) represent the earliest evidence of the Mexican turkey (Meleagris gallopavo) in the ancient Maya world. Archaeological, zooarchaeological, and ancient DNA evidence combine to confirm the identification and context. The natural pre-Hispanic range of the Mexican turkey does not extend south of central Mexico, making the species non-local to the Maya area where another species, the ocellated turkey (Meleagris ocellata), is indigenous. Prior to this discovery, the earliest evidence of M. gallopavo in the Maya area dated to approximately one thousand years later. The El Mirador specimens therefore represent previously unrecorded Preclassic exchange of animals from northern Mesoamerica to the Maya cultural region. As the earliest evidence of M. gallopavo found outside its natural geographic range, the El Mirador turkeys also represent the earliest indirect evidence for Mesoamerican turkey rearing or domestication. The presence of male, female and sub-adult turkeys, and reduced flight morphology further suggests that the El Mirador turkeys were raised in captivity. This supports an argument for the origins of turkey husbandry or at least captive rearing in the Preclassic.

Starting Point, Keys and Milestones of a Computer Code for the Simulation of the Behaviour of a Nuclear Fuel Rod

Directory of Open Access Journals (Sweden)

Armando C. Marino

2011-01-01

Full Text Available The BaCo code (“Barra Combustible” was developed at the Atomic Energy National Commission of Argentina (CNEA for the simulation of nuclear fuel rod behaviour under irradiation conditions. We present in this paper a brief description of the code and the strategy used for the development, improvement, enhancement, and validation of a BaCo during the last 30 years. “Extreme case analysis”, parametric (or sensitivity, probabilistic (or statistic analysis plus the analysis of the fuel performance (full core analysis are the tools developed in the structure of BaCo in order to improve the understanding of the burnup extension in the Atucha I NPP, and the design of advanced fuel elements as CARA and CAREM. The 3D additional tools of BaCo can enhance the understanding of the fuel rod behaviour, the fuel design, and the safety margins. The modular structure of the BaCo code and its detailed coupling of thermo-mechanical and irradiation-induced phenomena make it a powerful tool for the prediction of the influence of material properties on the fuel rod performance and integrity.

Radioactive lightning rods waste treatment

International Nuclear Information System (INIS)

Vicente, Roberto; Dellamano, Jose C.; Hiromoto, Goro

2008-01-01

Full text: In this paper, we present alternative processes that could be adopted for the management of radioactive waste that arises from the replacement of lightning rods with attached Americium-241 sources. Lightning protectors, with Americium-241 sources attached to the air terminals, were manufactured in Brazil until 1989, when the regulatory authority overthrew the license for fabrication, commerce, and installation of radioactive lightning rods. It is estimated that, during the license period, about 75,000 such devices were set up in public, commercial and industrial buildings, including houses and schools. However, the policy of CNEN in regard to the replacement of the installed radioactive rods, has been to leave the decision to municipal governments under local building regulations, requiring only that the replaced rods be sent immediately to one of its research institutes to be treated as radioactive waste. As a consequence, the program of replacement proceeds in a low pace and until now only about twenty thousand rods have reached the waste treatment facilities The process of management that was adopted is based primarily on the assumption that the Am-241 sources will be disposed of as radioactive sealed sources, probably in a deep borehole repository. The process can be described broadly by the following steps: a) Receive and put the lightning rods in initial storage; b) Disassemble the rods and pull out the sources; c) Decontaminate and release the metal parts to metal recycling; d) Store the sources in intermediate storage; e) Package the sources in final disposal packages; and f) Send the sources for final disposal. Up to now, the disassembled devices gave rise to about 90,000 sources which are kept in storage while the design of the final disposal package is in progress. (author)

Importance of biomass energy sources for Turkey

International Nuclear Information System (INIS)

Demirbas, Ayhan

2008-01-01

Various agricultural residues such as grain dust, crop residues and fruit tree residues are available in Turkey as the sources of biomass energy. Among the biomass energy sources, fuelwood seems to be one of the most interesting because its share of the total energy production of Turkey is high at 21% and the techniques for converting it to useful energy are not necessarily sophisticated. Selection of a particular biomass for energy requirements is influenced by its availability, source and transportation cost, competing uses and prevalent fossil fuel prices. Utilization of biomass is a very attractive energy resource, particularly for developing countries since biomass uses local feedstocks and labor. Like many developing countries, Turkey relies on biomass to provide much of its energy requirement. More efficient use of biomass in producing energy, both electrical and thermal, may allow Turkey to reduce petroleum imports, thus affecting its balance of payments dramatically. Turkey has always been one of the major agricultural countries in the world. The importance of agriculture is increasing due to biomass energy being one of the major resources in Turkey. Biomass waste materials can be used in Turkey to provide centralized, medium- and large-scale production of process heat for electricity production. Turkey's first biomass power project is under development in Adana province, at an installed capacity of 45 MW. Two others, at a total capacity of 30 MW, are at the feasibility study stage in Mersin and Tarsus provinces. Electricity production from biomass has been found to be a promising method in the nearest future in Turkey

Experimental benchmark data for PWR rod bundle with spacer-grids

International Nuclear Information System (INIS)

Dominguez-Ontiveros, Elvis E.; Hassan, Yassin A.; Conner, Michael E.; Karoutas, Zeses

2012-01-01

In numerical simulations of fuel rod bundle flow fields, the unsteady Navier–Stokes equations have to be solved in order to determine the time (phase) dependent characteristics of the flow. In order to validate the simulations results, detailed comparison with experimental data must be done. Experiments investigating complex flows in rod bundles with spacer grids that have mixing devices (such as flow mixing vanes) have mostly been performed using single-point measurements. In order to obtain more details and insight on the discrepancies between experimental and numerical data as well as to obtain a global understanding of the causes of these discrepancies, comparisons of the distributions of complete phase-averaged velocity and turbulence fields for various locations near spacer-grids should be performed. The experimental technique Particle Image Velocimetry (PIV) is capable of providing such benchmark data. This paper describes an experimental database obtained using two-dimensional Time Resolved Particle Image Velocimetry (TR-PIV) measurements within a 5 × 5 PWR rod bundle with spacer-grids that have flow mixing vanes. One of the unique characteristic of this set-up is the use of the Matched Index of Refraction technique employed in this investigation to allow complete optical access to the rod bundle. This unique feature allows flow visualization and measurement within the bundle without rod obstruction. This approach also allows the use of high temporal and spatial non-intrusive dynamic measurement techniques namely TR-PIV to investigate the flow evolution below and immediately above the spacer. The experimental data presented in this paper includes explanation of the various cases tested such as test rig dimensions, measurement zones, the test equipment and the boundary conditions in order to provide appropriate data for comparison with Computational Fluid Dynamics (CFD) simulations. Turbulence parameters of the obtained data are presented in order to gain

2D model for melt progression through rods and debris

International Nuclear Information System (INIS)

Fichot, F.

2001-01-01

During the degradation of a nuclear core in a severe accident scenario, the high temperatures reached lead to the melting of materials. The formation of liquid mixtures at various elevations is followed by the flow of molten materials through the core. Liquid mixture may flow under several configurations: axial relocation along the rods, horizontal motion over a plane surface such as the core support plate or a blockage of material, 2D relocation through a debris bed, etc.. The two-dimensional relocation of molten material through a porous debris bed, implemented for the simulation of late degradation phases, has opened a new way to the elaboration of the relocation model for the flow of liquid mixture along the rods. It is based on a volume averaging method, where wall friction and capillary effects are taken into account by introducing effective coefficients to characterize the solid matrix (rods, grids, debris, etc.). A local description of the liquid flow is necessary to derive the effective coefficients. Heat transfers are modelled in a similar way. The derivation of the conservation equations for the liquid mixture falling flow (momentum) in two directions (axial and radial-horizontal) and for the heat exchanges (energy) are the main points of this new model for simulating melt progression. In this presentation, the full model for the relocation and solidification of liquid materials through a rod bundle or a debris bed is described. It is implemented in the ICARE/CATHARE code, developed by IPSN in Cadarache. The main improvements and advantages of the new model are: A single formulation for liquid mixture relocation, in 2D, either through a rod bundle or a porous debris bed, Extensions to complex structures (grids, by-pass, etc..), The modeling of relocation of a liquid mixture over plane surfaces. (author)

Snubber assembly for a control rod drive

International Nuclear Information System (INIS)

1976-01-01

A snubber cartridge assembly is described which is mounted to the nozzle of a control rod drive mechanism to insure that it will be located within the liquid filled section of a nuclear reactor vessel whenever the control rod drive is assembled thereto. The snubber assembly includes a piston-mounted proximate to the control rod connecting end of the control rod drive leadscrew to allow the piston to travel within the liquid filled snubber cartridge and controllable exhaust the liquid during a 'scram' condition. The snubber cartridge provides three separate areas of increasing resistance to piston travel to insure a speedy but safe 'scram' of the control rod into the reactor

Automated nuclear fuel rod pattern loading system

International Nuclear Information System (INIS)

Lambert, D.V.; Nyland, T.W.; Byers, J.W.; Haley, D.E. Jr.; Cioffi, J.V.

1990-01-01

This patent describes an apparatus for loading fuel rods in a desired pattern. It comprises: a carousel having a plurality of movable gondolas for stocking thereon fuel rods of known enrichments; an elongated magazine defining a matrix of elongated slots being open at their forward ends for receiving fuel rods; a workstation defining a fuel rod feed path; and a holder and indexing mechanism for movably supporting the magazine and being actuatable for moving the magazine along X-Y axes to successively align one at a time selected ones of the slots with the feed path for loading in the magazine the successive fuel rods in a desired enrichment pattern

Snubber assembly for a control rod drive

International Nuclear Information System (INIS)

Matthews, J.C.

1978-01-01

A snubber cartridge assembly is mounted to the nozzle of a control rod drive mechanism to insure that the snubber assembly will be located within the liquid filled section of a nuclear reactor vessel whenever the control rod drive is assembled thereto. The snubber assembly includes a piston mounted proximate to the control rod connecting end of the control rod drive leadscrew to allow the piston to travel within the liquid filled snubber cartridge and controllably exhaust liquid therefrom during a ''scram'' condition. The snubber cartridge provides three separate areas of increasing resistance to piston travel to insure a speedy but safe ''scram'' of the control rod into the reactor

Method and apparatus for inspection of nuclear fuel rods

International Nuclear Information System (INIS)

Wachter, W.J.

1977-01-01

A method and apparatus are provided for the inspection of nuclear fuel rods to detect defects or failures in such rods. Assemblies of fuel rods are immersed in water and means are provided for causing a change in the relative pressures in the water and within the fuel rod such that fluid is expelled from the rod through any defects that may exist. Means are also provided for thereafter vibrating the rods to cause additional internal fluid or other material that may be trapped in the rod to be expelled. Sensors are provided for detecting the emission of bubbles of fluid or other material from the rod and for locating the position of the defective rod in the assembly. 5 figures

Implementation of CTRLPOS, a VENTURE module for control rod position criticality searches, control rod worth curve calculations, and general criticality searches

Energy Technology Data Exchange (ETDEWEB)

Smith, L.A.; Renier, J.P.

1994-06-01

A module in the VENTURE reactor analysis code system, CTRLPOS, is developed to position control rods and perform control rod position criticality searches. The module is variably dimensioned so that calculations can be performed with any number of control rod banks each having any number of control rods. CTRLPOS can also calculate control rod worth curves for a single control rod or a bank of control rods. Control rod depletion can be calculated to provide radiation source terms. These radiation source terms can be used to predict radiation doses to personnel and estimate the shielding and long-term storage requirements for spent control rods. All of these operations are completely automated. The numerous features of the module are discussed in detail. The necessary input data for the CTRLPOS module is explained. Several sample problems are presented to show the flexibility of the module. The results presented with the sample problems show that the CTRLPOS module is a powerful tool which allows a wide variety of calculations to be easily performed.

Absorber rod drive for nuclear reactors

International Nuclear Information System (INIS)

Acher, H.

1985-01-01

The invention concerns a further addition to the invention of DE 33 42 830 A1. The free contact of the hollow piston with the nut due to hydraulic pressure is replaced by a hydraulic or spring attachment. The pressure system required to produce the hydraulic pressure is therefore omitted, and the electrical power required for driving the pump or the mass flow is also omitted. The absorber rod slotted along its longitudinal axis is replaced by an absorber rod, in the longitudinal axis of which a hollow piston is connected together with the absorber rod. This makes the absorber rod more stable, and assembly is simplified. (orig./HP) [de

Nuclear reactor fuel rod attachment system

International Nuclear Information System (INIS)

Christiansen, D.W.

1983-01-01

The invention involves a technique to quickly, inexpensively and rigidly attach a nuclear reactor fuel rod to a support member. The invention also allows for the repeated non-destructive removal and replacement of the fuel rod. The proposed fuel rod and support member attachment and removal system consists of a locking cap fastened to the fuel rod and a locking strip fastened to the support member or vice versa. The locking cap has two or more opposing fingers shaped to form a socket. The fingers spring back when moved apart and released. The locking strip has an extension shaped to rigidly attach to the socket's body portion

Control device for the withdrawal of control rod

International Nuclear Information System (INIS)

Ando, Masaki.

1985-01-01

Purpose: To significantly suppress the maximum value of the control-rod worth upon control rod withdrawal. Constitution: At first, a signal for designating the first class is sent from a class-control section to the group-control section. In the group-control section, the peripheral group among the first class is designated by which the withdrawal of the control rods other than the peripheral group is inhibited and the control-rods in the peripheral group are withdrawn one by one. When all of them have been withdrawn, the group-control section designates the central group of the first class. All the control rods of the central group have been withdrawn, then the group-control section designates the peripheral group of the second class. Thereafter, the central group in the second class is designated. The control rods are thus withdrawn in the same manner hereinafter. The maximum value for the control-rod worth can be decreased by such a withdrawing sequence for the control rods. (Horiuchi, T.)

Temperature measurement in cans of fuel rods and fuel rod simulators

International Nuclear Information System (INIS)

Tschoeke, H.; Moeller, R.

1977-01-01

On the sodium-cooled 19-rod cluster model for the SNR 300 the can wall temperature distributions of the non-uniformly cooled rods were measured with thermocouples mounted in outer grooves in the peripheral zone, permitting, in connection with Ni solder, a practically undisturbed measurement. For a more exact determination of the local surface temperature a calibration method, the so-called double-wall method, was developed and applied. The description of this calibration method and the experimental results achieved until now are presented. (orig./RW) [de

Local Agenda 21 and sustainable development: The case of Harran, Turkey

Directory of Open Access Journals (Sweden)

Reyhan Genli Yiğiter

2011-01-01

Full Text Available The twenty-first century is the beginning of an era in which urban development at the international and national levels, equality, continuity, capability, administration involving many actors and settlement systems need to be dealt with using new settlement administration ethics. The concept of sustainable development first came up at the National Development and Environment Conference held in 1992 in Rio de Janeiro, when the action plan known as Agenda 21 was constituted at the Earth Summit. This is a comprehensive document assigning responsibility to governments, NGOs, local authorities, United Nations organisations, development organisations and all persons and institutions that have an impact on the environment. On this basis, this study evaluates the growing necessity of urban transformation in Turkey in various dimensions within the framework of Local Agenda 21, in which various actors can be involved. This paper approaches the issues not only from the point of view of the state, but also from the point of view of all actors to whom responsibility is assigned. It examines the philosophy of the Local Agenda 21 program and how it is being implemented in the Municipality of Harran, and it assesses the achievement level of Local Agenda 21 in Turkey and policies in the case reviewed. The paper includes proposals that will allow all local authorities in Turkey to examine their own programs within the framework of the Local Agenda 21 action program so that they can participate in the urban transformation process, develop local sustainable development policies and establish short-term and long-term strategic plans to solve problems.

Development of cutting device for irradiated fuel rod

International Nuclear Information System (INIS)

Lee, E. P.; Jun, Y. B.; Hong, K. P.; Min, D. K.; Lee, H. K.; Su, H. S.; Kim, K. S.; Kwon, H. M.; Joo, Y. S.; Yoo, K. S.; Joo, J. S.; Kim, E. K.

2004-01-01

Post Irradiation Examination(PIE) on irradiated fuel rods is essential for the evaluation of integrity and irradiation performance of fuel rods of commercial reactor fuel. For PIE, fuel rods should be cut very precisely. The cutting positions selected from NDT data are very important for further destructive examination and analysis. A fuel rod cutting device was developed witch can cut fuel rods longitudinal very precisely and can also cut the fuels into the same length rod cuts repeatedly. It is also easy to remove the fuel cutting powder after cutting works and it can extend the life time of cutting device and lower the contamination level of hot cell

Fabrication Of Control Rod System Of The RSG-GAS

International Nuclear Information System (INIS)

Sudirdjo, Hari; Setyono; Prasetya, Hendra

2001-01-01

Eight units of control rod mechanical system of RSG-GAS has been fabricated. The control rod mechanical system of RSG-GAS consist of guide tube and lifting rod. Complete construction of the control rod mechanical system of RSG-GAS are guide tube, lifting rod, absorber, and absorber casing. The eight units of the control rod mechanical system of RSG-GAS has been fabricated according to the mechanical engineering design

Microcomputer system for controlling fuel rod length

International Nuclear Information System (INIS)

Meyer, E.R.; Bouldin, D.W.; Bolfing, B.J.

1979-01-01

A system is being developed at the Oak Ridge National Laboratory (ORNL) to automatically measure and control the length of fuel rods for use in a high temperature gas-cooled reactor (HTGR). The system utilizes an LSI-11 microcomputer for monitoring fuel rod length and for adjusting the primary factor affecting length. Preliminary results indicate that the automated system can maintain fuel rod length within the specified limits of 1.940 +- 0.040 in. This system provides quality control documentation and eliminates the dependence of the current fuel rod molding process on manual length control. In addition, the microcomputer system is compatible with planned efforts to extend control to fuel rod fissile and fertile material contents

Development of the auto gas and LPG-powered vehicle sector in Turkey: A statistical case study of the sector for Bursa

International Nuclear Information System (INIS)

Karamangil, M. Ihsan

2007-01-01

In this paper, the development of LPG-powered vehicle sector in Turkey and the policies applied by the Turkish Government as well as the total fleet of LPG-powered vehicles in Bursa province, which is assumed as typical district to represent whole Turkey, are analyzed. We also tried to point out economical losses and applicational problems caused by wrong energy and environmental policies in Turkey. We aimed to focus a guiding light on the newly developing auto gas markets in different countries through the problems resulting from the fast growth of the sector and the experiences in Turkish application

A system automatic study for the spent fuel rod cutting and simulated fuel pellet extraction device

International Nuclear Information System (INIS)

Jeong, J. H.; Yun, J. S.; Hong, D. H.; Kim, Y. H.; Park, K. Y.

2001-01-01

A fuel pellet extraction device of the spent fuel rods is described. The device consists of a cutting device of the spent fuel rods and the decladding device of the fuel pellets. The cutting device is to cut a spent fuel rod to n optimal size for fast decladding operation. To design the device, the fuel rod properties are investigated including the dimension and material of fuel rod tubes and pellets. Also, various methods of existing cutting method are investigated. The design concepts accommodate remote operability for the Hot-Cell(radioactive ) area operation. Also, the modularization of the device structure is considered for the easy maintenance. The decladding device is to extract the fuel pellet from the rod cut. To design this device, the existing method is investigated including the chemical and mechanical decladding methods. From the view point of fuel recovery and feasibility of implementation. it is concluded that the chemical decladding method is not appropriate due to the mass production of radioactive liquid wastes, in spite of its high fuel recovery characteristics. Hence, in this paper, the mechanical decladding method is adopted and the device is designed so as to be applicable to various lengths of rod-cuts. As like the cutting device,the concepts of remote operability and maintainability is considered. Both devices are fabricated and the performance is investigated through a series of experiments. From the experimental result, the optimal operational condition of the devices is established

ECONOMIC RELATIONS BETWEEN REPUBLIC OF MOLDOVA AND TURKEY

Directory of Open Access Journals (Sweden)

Bestenigar KARA

2015-07-01

Full Text Available The topic of article is bilateral economical and foreign trade relations between Turkey, which has started to apply outward-oriented economic policies since globalization and Moldova, which has done market transition after breaking up with the Soviet Union. Within this frame, the subject of article has been searched in depth as follows: general overview of Turkey’s economic relations, overall picture of Moldovan-Turkish relations, short exposition of Moldovan economy and bilateral economic and foreign trade relations of Moldova and Turkey. The topic of article is a current issue. Because Moldova, which is closed to Turkey in terms of geography, culture and history always has been an attractive country politico-economically for Turkey since its independence. Bilateral economic relations starting with shuttle trade have formalized and further developed and Turkey became as one of top ten biggest economic and trade partner of Moldova. On this basis, the aim of study is to elucidate foreign trade of Turkey with Moldova and to compare performances of Turkey by years and by other countries, which have remarkable domination in Moldovan market. Within this scope, bilateral trade volume of Moldova and Turkey has increased year by year considering the past decade, which makes Turkey as the 7th largest import and 8th export partner of Moldova. Turkey aims to be one of the first three biggest economic partner of Moldova after entry into force of Free Trade Agreement (FTA, which was signed by both countries in 2014 to increase foreign trade volume up to 1 billion US dollars.

Reconstruction-of-difference (RoD) imaging for cone-beam CT neuro-angiography

Science.gov (United States)

Wu, P.; Stayman, J. W.; Mow, M.; Zbijewski, W.; Sisniega, A.; Aygun, N.; Stevens, R.; Foos, D.; Wang, X.; Siewerdsen, J. H.

2018-06-01

Timely evaluation of neurovasculature via CT angiography (CTA) is critical to the detection of pathology such as ischemic stroke. Cone-beam CTA (CBCT-A) systems provide potential advantages in the timely use at the point-of-care, although challenges of a relatively slow gantry rotation speed introduce tradeoffs among image quality, data consistency and data sparsity. This work describes and evaluates a new reconstruction-of-difference (RoD) approach that is robust to such challenges. A fast digital simulation framework was developed to test the performance of the RoD over standard reference reconstruction methods such as filtered back-projection (FBP) and penalized likelihood (PL) over a broad range of imaging conditions, grouped into three scenarios to test the trade-off between data consistency, data sparsity and peak contrast. Two experiments were also conducted using a CBCT prototype and an anthropomorphic neurovascular phantom to test the simulation findings in real data. Performance was evaluated primarily in terms of normalized root mean square error (NRMSE) in comparison to truth, with reconstruction parameters chosen to optimize performance in each case to ensure fair comparison. The RoD approach reduced NRMSE in reconstructed images by up to 50%–53% compared to FBP and up to 29%–31% compared to PL for each scenario. Scan protocols well suited to the RoD approach were identified that balance tradeoffs among data consistency, sparsity and peak contrast—for example, a CBCT-A scan with 128 projections acquired in 8.5 s over a 180°  +  fan angle half-scan for a time attenuation curve with ~8.5 s time-to-peak and 600 HU peak contrast. With imaging conditions such as the simulation scenarios of fixed data sparsity (i.e. varying levels of data consistency and peak contrast), the experiments confirmed the reduction of NRMSE by 34% and 17% compared to FBP and PL, respectively. The RoD approach demonstrated superior performance in 3D angiography

Nursing doctoral education in Turkey.

Science.gov (United States)

Yavuz, Meryem

2004-10-01

Quality health care is an issue of concern worldwide, and nursing can and must play a major and global role in transforming the healthcare environment. Doctorally prepared nurses are very much needed in the discipline to further develop and expand the science, as well as to prepare its future educators, scholars, leaders, and policy makers. In 1968, the Master of Science in Nursing Program was initiated in Turkey, followed by the Nursing Doctoral Education Program in 1972. Six University Schools of Nursing provide nursing doctoral education. By the graduating year of 2001, 154 students had graduated with the Doctor of Philosophy in Nursing (Ph.D.), and 206 students were enrolled in related courses. Many countries in the world are systematically building various collaborative models in their nursing doctoral education programs. Turkey would like to play an active role in creating collaborative nursing doctoral education programs with other countries. This paper centres on the structure and model of doctoral education for nurses in Turkey. It touches on doctoral programs around the world; describes in detail nursing doctoral education in Turkey, including its program structure, admission process, course units, assessment strategies and dissertation procedure; and discusses efforts to promote Turkey as a potential partner in international initiatives to improve nursing doctoral education.

Control rod for a nuclear reactor

Science.gov (United States)

Roman, Walter G.; Sutton, Jr., Harry G.

1979-01-01

A control rod assembly for a nuclear reactor is disclosed having a remotely disengageable coupling between the control rod and the control rod drive shaft. The coupling is actuated by first lowering then raising the drive shaft. The described motion causes axial repositioning of a pin in a grooved rotatable cylinder, each being attached to different parts of the drive shaft which are axially movable relative to each other. In one embodiment, the relative axial motion of the parts of the drive shaft is used either to couple or to uncouple the connection by forcing resilient members attached to the drive shaft into or out of shouldered engagement, respectively, with an indentation formed in the control rod.

Control rod for a nuclear reactor

International Nuclear Information System (INIS)

Roman, W.G.; Sutton, H.G. Jr.

1976-01-01

A control rod assembly for a nuclear reactor is disclosed having a remotely disengageable coupling between the control rod and the control rod drive shaft. The coupling is actuated by first lowering then raising the drive shaft. The described motion causes axial repositioning of a pin in a grooved rotatable cylinder, each being attached to different parts of the drive shaft which are axially movable relative to each other. In one embodiment, the relative axial motion of the parts of the drive shaft is used either to couple or to uncouple the connection by forcing resilent members attached to the drive shaft into or out of shouldered engagement, respectively, with an indentation formed in the control rod

Control rod for a nuclear reactor

International Nuclear Information System (INIS)

Roman, W.G.; Sutton, H.G. Jr.

1979-01-01

A control rod assembly for a nuclear reactor is disclosed having a remotely disengageable coupling between the control rod and the control rod drive shaft. The coupling is actuated by first lowering then raising the drive shaft. The described motion causes axial repositioning of a pin in a grooved rotatable cylinder, each being attached to different parts of the drive shaft which are axially movable relative to each other. In one embodiment, the relative axial motion of the parts of the drive shaft is used either to couple or to uncouple the connection by forcing resilient members attached to the drive shaft into or out of shouldered engagement, respectively, with an indentation formed in the control rod

Turkey-U.S. Defense Cooperation: Prospects and Challenges

Science.gov (United States)

2011-04-08

to cultivate stability or to be unduly provocative to neighboring countries. • Arms sales and industrial cooperation: Turkey continues to seek... mushroomed and Kurdish secessionist sentiment within Turkey caused concerns in the 1990s following the establishment of an autonomous Kurdish zone...a member of NATO), and has counted on previously close Turkey-Israel military relations to cultivate U.S.-Turkey-Israel military cooperation

Determination of incoming solar radiation in major tree species in Turkey.

Science.gov (United States)

Yilmaz, Osman Yalcin; Sevgi, Orhan; Koc, Ayhan

2012-07-01

Light requirements and spatial distribution of major forest tree species in Turkey hasn't been analyzed yet. Continuous surface solar radiation data, especially at mountainous-forested areas, are needed to put forward this relationship between forest tree species and solar radiation. To achieve this, GIS-based modeling of solar radiation is one of the methods used in rangelands to estimate continuous surface solar radiation. Therefore, mean monthly and annual total global solar radiation maps of whole Turkey were computed spatially using GRASS GIS software "r.sun" model under clear-sky (cloudless) conditions. 147498 pure forest stand point-based data were used in the study for calculating mean global solar radiation values of all the major forest tree species of Turkey. Beech had the lowest annual mean total global solar radiation value of 1654.87 kWh m(-2), whereas juniper had the highest value of 1928.89 kWh m(-2). The rank order of tree species according to the mean monthly and annual total global solar radiation values, using a confidence level of p solar radiation values of sites and light requirements of forest trees ranked similarly.

ABWR-II Core Design with Spectral Shift Rods for Operation with All Control Rods Withdrawn

International Nuclear Information System (INIS)

Moriwaki, Masanao; Aoyama, Motoo; Anegawa, Takafumi; Okada, Hiroyuki; Sakurada, Koichi; Tanabe, Akira

2004-01-01

An innovative reactor core concept applying spectral shift rods (SSRs) is proposed to improve the plant economy and the operability of the 1700-MW(electric) Advanced Boiling Water Reactor II (ABWR-II). The SSR is a new type of water rod in which a water level is naturally developed during operation and changed according to the coolant flow rate through the channel. By taking advantage of the large size of the ABWR-II bundle, the enhanced spectral shift operation by eight SSRs allows operation of the ABWR-II with all control rods withdrawn. In addition, the uranium-saving factor of 6 to 7% relative to the reference ABWR-II core with conventional water rods can be expected due to the greater effect of spectral shift. The combination of these advantages means the ABWR-II with SSRs should be an attractive alternative for the next-generation nuclear reactor

Process and apparatus for controlling control rods

International Nuclear Information System (INIS)

Gebelin, B.; Couture, R.

1987-01-01

This process and apparatus is characterized by 2 methods, for examination of cluster of nuclear control rods. Foucault current analyzer which examines fraction by fraction all the control rods. This examination is made by rotation of the cluster. Doubtful rods are then analysed by ultrasonic probe [fr

Performance of the NRX shut-off rods

International Nuclear Information System (INIS)

Manson, R.E.

1965-08-01

A new type of shut-off rod of electromechanical design was developed by the American Machine and Foundry Company for use in the NRX reactor following the accident of 1952. The new rods were installed in May, 1956, as part of the control system conversion program which was completed in 1958. Some problems were encountered with limit switch adjustment but minor modifications in design led to much improved operation. he performance of the rods also improved as more experience was gained in the maintenance and adjustment of the various headgear components. Each headgear is now overhauled once a year on a routine basis. The present design of shut-off rod is considered to be very satisfactory. There has only been one occasion when a shut-off rod has failed to come fully down on a trip. Rods have failed to operate correctly on five other occasions but these occurred during shutdown periods or when the reactor was being shutdown manually. (author)

Control rod supporting device in reactor

International Nuclear Information System (INIS)

Seki, Osamu; Itooka, Satoshi; Harada, Kiyoshi; Jodoi, Takashi.

1990-01-01

Since coolants flowing from a reactor core hit against a control rod and a control rod connection pipe, a considerable amount of bending moment for separating an attracting surface between an electromagnet and an armature is formed. Then, a plurality of grooves are formed on a heat sensitive material to dispose a heat collecting fin, and each of upper and lower contact portions of a control rod supporting portion in which the flanged portion of T-like cross section does not slip out is made into a partial spheric surface and a portion between the electromagnet and the attracted member are engaged by the unevenness. With such a constitution, even if a bending moment is applied, the control rod only swings and the bending moment is not transmitted to the attracted member. Further, since the temperature of the heat sensitive material can be rapidly made closer to the peripheral temperature by using the heat collecting fin, the timing for separation is made accurate. Further, since the engaging portion is brought into contact at the spheric surface, the load distribution on the control rod is made uniform, and the positional relationship is made accurate, to support the control rod reliably and the separation depends only on the temperature of the coolants. (N.H.)

Energy production for environmental issues in Turkey

Science.gov (United States)

Yuksel, Ibrahim; Arman, Hasan; Halil Demirel, Ibrahim

2017-11-01

Due to the diversification efforts of energy sources, use of natural gas that was newly introduced into Turkish economy, has been growing rapidly. Turkey has large reserves of coal, particularly of lignite. The proven lignite reserves are 8.0 billion tons. The estimated total possible reserves are 30 billion tons. Turkey, with its young population and growing energy demand per person, its fast growing urbanization, and its economic development, has been one of the fast growing power markets of the world for the last two decades. It is expected that the demand for electric energy in Turkey will be 580 billion kWh by the year 2020. Turkey's electric energy demand is growing about 6-8% yearly due to fast economic growing. This paper deals with energy demand and consumption for environmental issues in Turkey.

Development of self-actuated shutdown system using curie point electromagnet

International Nuclear Information System (INIS)

Kim, Tae Ryong; Park, Jin Ho

1999-01-01

An innovative concept for a passive reactor shutdown system, so called self-actuated shutdown system (SASS), is inevitably required for the inherent safety in liquid metal reactor, which is designed with the totally different concept from the usual reactor shutdown system in LWR. SASS using Curie point electromagnet (CPEM) was selected as the passive reactor shutdown system for KALIMER (Korea Advanced Liquid Metal Reactor). A mock-up of the SASS was designed, fabricated and tested. From the test it was confirmed that the mockup was self-actuated at the Curie point of the temperature sensing material used in the mockup. An articulated control rod was also fabricated and assembled with the CPEM to confirm that the control rod can be inserted into core even when the control rod guide tube is deformed due to earthquake. The operability of SASS in the actual sodium environment should be confirmed in the future. All the design and test data will be applied to the KALIMER design. (author)

Cuisenaire Rods Go to College.

Science.gov (United States)

Chinn, Phyllis; And Others

1992-01-01

Presents examples of questions and answers arising from a hands-on and exploratory approach to discrete mathematics using cuisenaire rods. Combinatorial questions about trains formed of cuisenaire rods provide the setting for discovering numerical patterns by experimentation and organizing the results using induction and successive differences.…

Control rod driving mechanism

International Nuclear Information System (INIS)

Ooshima, Yoshio.

1983-01-01

Purpose: To perform reliable scram operation, even if abnormality should occur in a system instructing scram operation in FBR type reactors. Constitution: An aluminum alloy member to be melt at a predetermined temperature (about 600sup(o)C) is disposed to a connection part between a control rod and a driving mechanism, whereby the control rod is detached from the driving mechanism and gravitationally fallen to the reactor core. (Ikeda, J.)

Study of thermal hydraulic behavior of supercritical water flowing through fuel rod bundles

International Nuclear Information System (INIS)

Thakre, Sachin; Lakshmanan, S.P.; Kulkarni, Vinayak; Pandey, Manmohan

2009-01-01

Investigations on thermal-hydraulic behavior in Supercritical Water Reactor (SCWR) fuel assembly have obtained a significant attention in the international SCWR community because of its potential to obtain high thermal efficiency and compact design. Present work deals with CFD analysis to study the flow and heat transfer behavior of supercritical water in 4 metre long 7-pin fuel bundle using commercial CFD package ANSYS CFX for single phase steady state conditions. Considering the symmetric conditions, 1/12th part of the fuel rod bundle is taken as a domain of analysis. RNG K-epsilon model with scalable wall functions is used for modeling the turbulence behavior. Constant heat flux boundary condition is applied at the fuel rod surface. IAPWS equations of state are used to compute thermo-physical properties of supercritical water. Sharp variations in its thermo-physical properties (specific heat, density) are observed near the pseudo-critical temperature causing sharp change in heat transfer coefficient. The pseudo-critical point initially appears in the gaps among heated fuel rods, and then spreads radially outward reaching the adiabatic wall as the flow goes downstream. The enthalpy gain in the centre of the channel is much higher than that in the wall region. Non-uniformity in the circumferential distribution of surface temperature and heat transfer coefficient is observed which is in agreement with published literature. Heat transfer coefficient is high on the rod surface near the tight region and decreases as the distance between rod surfaces increases. (author)

Biotechnology in Turkey: an overview.

Science.gov (United States)

Ozdamar, Tunçer H

2009-07-01

The term biotechnology first appeared in the programs of the Scientific and Technological Research Council of Turkey (TUBITAK) in 1982. The State Planning Organization (SPO) in 1988 defined biotechnology and the scientific fields. Moreover, it put forward an institutional framework and suggested priority areas for research and development. Turkey has been researching and investing in biotechnology for almost four decades. This review covers the development of science and technology policy with its history, consensus and consequences, bio-industries in Turkey, and research activities in biotechnology at Turkish Universities. Details are provided by the research groups in response to a common request for information on their activities and major publications in the field. The information provided has been grouped under thematic topics within the broad theme of biotechnology, and summarized within these topics. Although many aspects of biotechnological research are being pursued in Turkey, it appears that the most common research activities of the field are in fermentation processes, environmental biotechnology, and biomedical engineering.

Human Metapneumovirus in Turkey Poults

Science.gov (United States)

Velayudhan, Binu T.; Nagaraja, Kakambi V.; Thachil, Anil J.; Shaw, Daniel P.; Gray, Gregory C.

2006-01-01

This study was conducted to reexamine the hypothesis that human metapneumovirus (hMPV) will not infect turkeys. Six groups of 2-week-old turkeys (20 per group) were inoculated oculonasally with 1 of the following: noninfected cell suspension; hMPV genotype A1, A2, B1, or B2; or avian metapneumovirus (aMPV) subtype C. Poults inoculated with hMPV showed nasal discharge days 4–9 postexposure. Specific viral RNA and antigen were detected by reverse-transcription PCR and immunohistochemical evaluation, respectively, in nasal turbinates of birds exposed to hMPV. Nasal turbinates of hMPV-infected turkeys showed inflammatory changes and mucus accumulation. Each of the 4 hMPV genotypes caused a transient infection in turkeys as evidenced by clinical signs, detection of hMPV in turbinates, and histopathologic examination. Detailed investigation of cross-species pathogenicity of hMPV and aMPV and its importance for human and animal health is needed. PMID:17235379

Prediction of failure enthalpy and reliability of irradiated fuel rod under reactivity-initiated accidents by means of statistical approach

International Nuclear Information System (INIS)

Nam, Cheol; Choi, Byeong Kwon; Jeong, Yong Hwan; Jung, Youn Ho

2001-01-01

During the last decade, the failure behavior of high-burnup fuel rods under RIA has been an extensive concern since observations of fuel rod failures at low enthalpy. Of great importance is placed on failure prediction of fuel rod in the point of licensing criteria and safety in extending burnup achievement. To address the issue, a statistics-based methodology is introduced to predict failure probability of irradiated fuel rods. Based on RIA simulation results in literature, a failure enthalpy correlation for irradiated fuel rod is constructed as a function of oxide thickness, fuel burnup, and pulse width. From the failure enthalpy correlation, a single damage parameter, equivalent enthalpy, is defined to reflect the effects of the three primary factors as well as peak fuel enthalpy. Moreover, the failure distribution function with equivalent enthalpy is derived, applying a two-parameter Weibull statistical model. Using these equations, the sensitivity analysis is carried out to estimate the effects of burnup, corrosion, peak fuel enthalpy, pulse width and cladding materials used

Expandable device for a nuclear fuel rod

International Nuclear Information System (INIS)

Gesinski, L.T.

1978-01-01

A nuclear fuel rod and a device for use within the rod cladding to maintain the axial position of the fuel pellets stacked one atop another within the cladding are described. The device is initially of a smaller external cross-section than the fuel rod cladding internal cross-section so as to accommodate loading into the rod at preselected locations. During power operation the device responds to a rise in temperature, so as to permanently maintain its position and restrain any axial motion of the fuel pellets

GLOBAL SOURCING: A THEORETICAL STUDY ON TURKEY

Directory of Open Access Journals (Sweden)

Aytac GOKMEN

2010-07-01

Full Text Available Global sourcing is to source from the global market for goods and services across national boundaries in order to take advantage of the global efficiencies in the delivery of a product or service. Such efficiencies are consists of low cost skilled labor, low cost raw materials and other economic factors like tax breaks and deductions as well as low trade tariffs. When we assess the case regarding to Turkey, global sourcing is an effective device for some firms. The domestic firms in Turkey at various industries are inclined to global source finished or intermediate goods from the world markets, finish the production process in Turkey and export. Eventually, on the one hand the export volume of Turkey increases, but on the other hand the import of a considerable volume of finished or intermediate goods bring about a negative trade balance and loss of jobs in Turkey. Therefore, the objective of this study is to assess the concept of global sourcing transactions on Turkey resting on comprehensive publications.

Method and apparatus for compacting spent nuclear reactor fuel rods

International Nuclear Information System (INIS)

Wachter, W.J.

1988-01-01

In a nuclear reactor system requiring periodic physical manipulation of spent fuel rods, the method of compacting fuel rods from a fuel rod assembly is described comprising the steps of: (1) removing the top end from pulling members having electrodes of weld elements in leading ends thereof in sequence through a fuel rod container and thence through respective consolidating passages in a fuel-rod directing chamber; (3) welding the weld elements of the pulling members to the top end of respective fuel rods corresponding to the respective pulling members; (4) drawing each of the pulling members axially to draw the respective engaged fuel rods in one axial direction through the respective passages in the chamber to thereby consolidate the fuel rods into a compacted configuration of a cross-sectional area smaller than the cross-sectional area occupied thereby within the fuel rod assembly; and (5) drawing all of the engaged fuel rods concurrently and substantially parallel to one another to the one axial direction into the fuel rod container while maintaining the compacting configuration in a fuel rod density which is greater than that of the fuel rod density of the fuel rod assembly

Hepatic lipidosis in turkeys.

Science.gov (United States)

Gazdzinski, P; Squires, E J; Julian, R J

1994-01-01

Two flocks of 14,000 twenty-week-old turkey hens each experienced increased mortality due to hepatic lipidosis. Some hens showed signs of dyspnea and cyanosis before death. Necropsy revealed dark muscles and enlarged livers with pale areas and numerous hemorrhages. Petechial and ecchymotic hemorrhages were also found on the abdominal fat and epicardium. Lung congestion and edema were prominent. In the heart and blood vessels, the blood was uncoagulated. Mortality was elevated for 12 days and resulted in the death of 0.7% of the turkey hens in one flock and 1.7% in the other. Vitamin E administered in water at a dose of 25 IU per hen appeared to reduce mortality. The nutritional and environmental factors that may contribute to the development of hepatic lipidosis in turkeys are discussed.

[Opening speech by President Suleyman Demirel for the meeting "Population Issues in Turkey: Policy Priorities"].

Science.gov (United States)

Demirel, S

1994-01-01

Mr. Demirel says that at the root of all problems faced by society is population growth. He points out that with an annual population growth of about 2.5%, Turkey's standard of living will be low even if it is possible to feed the growing population, and he says Turkey's first goal should be to create public awareness of individual responsibilities. In this task, Mr. Demirel adds, the government, the parliament, educational institutions, the media, voluntary organizations, and scientists all have a role to play. Mr. Demirel states that Turkey's second goal should be to bring down the rate of population growth to around 1% within 20 years. The country's third goal, according to Mr. Demirel, should be to reduce the proportion of the population dependent on agriculture, since population growth is highest in rural areas and migration into urban areas is taxing city resources and creating slum communities. Mr. Demirel adds that dependence on agriculture will not create wealth for a nation and says that the goal should be to reduce Turkey's approximately 50% dependence on agriculture to about 10%, also within 20 years. Mr. Demirel goes on to point out that 50% of Turkey's population remains outside the social security umbrella and that in rural areas children represent a family's security during old age. It is therefore imperative to expand the social security umbrella. Turkey's fourth goal, as put forth by Mr. Demirel, should be to ensure orderly development. To increase the standard of living, the rate of population growth must be reduced while increasing the rate of development. He adds that it is also important to improve the distribution of wealth. This, says Mr. Demirel, is his fifth goal and can be achieved by overcoming the regional differences in rates of development with the aim of directing the inevitable migration from rural areas to nearby small cities, away from the large cities of Ankara, Istanbul, and Izmir. Mr. Demirel says that it will take time to

Review of the social and environmental factors affecting the behavior and welfare of turkeys (Meleagris gallopavo).

Science.gov (United States)

Marchewka, J; Watanabe, T T N; Ferrante, V; Estevez, I

2013-06-01

In modern rearing systems, turkey producers often face economic losses due to increased aggression, feather pecking, cannibalism, leg disorders, or injuries among birds, which are also significant welfare issues. The main underlying causes appear to relate to rapid growth, flock size, density, poor environmental complexity, or lighting, which may be deficient in providing the birds with an adequate physical or social environment. To date, there is little information regarding the effect of these factors on turkey welfare. This knowledge is, however, essential to ensure the welfare of turkeys and to improve their quality of life, but may also be beneficial to industry, allowing better bird performance, improved carcass quality, and reduced mortality and condemnations. This paper reviews the available scientific literature related to the behavior of turkeys as influenced by the physical and social environment that may be relevant to advances toward turkey production systems that take welfare into consideration. We addressed the effects that factors such as density, group size, space availability, maturation, lightning, feeding, and transport may have over parameters that may be relevant to ensure welfare of turkeys. Available scientific studies were based in experimental environments and identified individual factors corresponding to particular welfare problems. Most of the studies aimed at finding optimal levels of rearing conditions that allow avoiding or decreasing most severe welfare issues. This paper discusses the importance of these factors for development of production environments that would be better suited from a welfare and economic point of view.

Shock analysis on hydraulic drive control rod during scram

International Nuclear Information System (INIS)

Song Wei; Qin Benke; Bo Hanliang

2013-01-01

Control rod hydraulic drive mechanism (CRHDM) is a new invention of Institute of Nuclear and New Energy Technology of Tsinghua University. The hydraulic absorber buffers the control rod when it scrams. The control rod fast drop impact experiment was conducted and the key parameters of control rod hydraulic buffering performance were obtained. Based on the test results and according to D'Alembert principle, the maximum inertial impact force on the control rod during the fast drop period was applied as equivalent static load force on the control rod. The deformations and stress distributions on the control rod in this worst case were calculated by using finite element software ABAQUS. Calculation results were compared with the experiment results, and it was verified that nonlinear transient dynamics analysis in this problem can be simplified as static analysis. Damage criterion of the control rod fast drop impact process was also given. And it lays foundation for optimal design of the control rod and hydraulic absorber. (authors)

Turkey's natural gas necessity, consumption and future perspectives

International Nuclear Information System (INIS)

Kilic, A.M.

2006-01-01

Turkey is an important candidate to be the 'energy corridor' in the transmission of the abundant oil and natural gas resources of the Middle East and Middle Asia countries to the Western market. Furthermore, Turkey is planning to increase its oil and gas pipeline infrastructure to accommodate its increased energy consumption. Naturally, Turkish natural gas usage is projected to increase remarkably in coming years, with the prime consumers, expected to be industry and power plants. Energy demand of Turkey is growing by 8% annually, one of the highest rates in the world. In addition, natural gas consumption is the fastest growing primary energy source in Turkey. Gas sales started at 0.5 bcm (billion cubic meters), in 1987 and reached approximately 22 bcm in 2003. This article deals with energy policies and natural gas consumption of Turkey. Besides modernization of present lines and realization of capacity increase, new lines will also be needed. In this context, Turkey, due to its geographical location is, in an important position to vary European supply. Therefore, Turkey's role as a transitory area gains importance

Acoustic loading effects on oscillating rod bundles

International Nuclear Information System (INIS)

Lin, W.H.

1980-01-01

An analytical study of the interaction between an infinite acoustic medium and a cluster of circular rods is described. The acoustic field due to oscillating rods and the acoustic loading on the rods are first solved in a closed form. The acoustic loading is then used as a forcing function for rod responses, and the acousto-elastic couplings are solved simultaneously. Numerical examples are presented for several cases to illustrate the effects of various system parameters on the acoustic reaction force coefficients. The effect of the acoustic loading on the coupled eigenfrequencies are discussed

Thorium research and development in Turkey

International Nuclear Information System (INIS)

Güngör, Görkem

2015-01-01

Turkey has a great potential regarding thorium resources. Thorium exploration activities have been done in the past mainly by state organizations for determining the thorium resources in Turkey. Thorium occurs as complex mineral together with barite, fluorite and rare earth elements (REE). The increase in global demand for REE creates the opportunity for REE production which will also produce thorium as a by-product. The development of nuclear energy program in Turkey provides the stimulus for research and development activities in nuclear technologies. The final declaration of the workshop emphasizes the importance of thorium reserves in Turkey and the necessity for thorium exploration and development activities in order to determine the feasibility of thorium mining and fuel cycle in Turkey. These activities should be conducted together with the development of technologies for separation of these complex minerals and purification of thorium, REE and other minerals to be utilized as commercial products. There are advanced academic research studies on thorium fuel cycle which should be supported by the industry in order to commercialize the results of these studies. Turkey should be integrated to international R and D activities on ADS which is expected to commercialize on medium term. The legislative framework should be developed in order to provide the industrial baseline for nuclear technologies independent from nuclear regulatory activities

Posttest examination of the VVER-1000 fuel rod bundle CORA-W2

International Nuclear Information System (INIS)

Sepold, L.

1995-06-01

The bundle meltdown experiment CORA-W2, representing the behavior of a Russian type VVER-1000 fuel element, with one B 4 C/stainless steel absorber rod was selected by the OECD/CSNI as International Standard Problem (ISP-36). The experimental results of CORA-W2 serve as data base for comparison with analytical predictions of the high-temperature material behavior by various code systems. The first part of the experimental results is described in KfK 5363 (1994), the second part is documented in this report which contains the destructive post-test examination results. The metallographical and analytical (SEM/EDX) post-test examinations were performed in Germany and Russia and are summarized in five individual contributions. The upper half of the bundle is completely oxidized, the lower half has kept the fuel rods relatively intact. The post-test examination results show the strong impact of the B 4 C absorber rod and the stainless steel grid spacers on the ''low-temperature'' bundle damage initiation and progression. The B 4 C absorber rod completely disappeared in the upper half of the bundle. The multicomponent melts relocated and formed coolant channel blockages on solidification with a maximum extent of about 30% in the lower part of the bundle. At temperatures above the melting point of the ZrNb1 cladding extensive fuel dissolution occurred. (orig.) [de

Control Rod Malfunction at the NRAD Reactor

Energy Technology Data Exchange (ETDEWEB)

Thomas L. Maddock

2010-05-01

The neutron Radiography Reactor (NRAD) is a training, research, and isotope (TRIGA) reactor located at the INL. The reactor is normally shut down by the insertion of three control rods that drop into the core when power is removed from electromagnets. During a routine shutdown, indicator lights on the console showed that one of the control rods was not inserted. It was initially thought that the indicator lights were in error because of a limit switch that was out of adjustment. Through further testing, it was determined that the control rod did not drop when the scram switch was initially pressed. The control rod anomaly led to a six month shutdown of the reactor and an in depth investigation of the reactor protective system. The investigation looked into: scram switch operation, console modifications, and control rod drive mechanisms. A number of latent issues were discovered and corrected during the investigation. The cause of the control rod malfunction was found to be a buildup of corrosion in the control rod drive mechanism. The investigation resulted in modifications to equipment, changes to both operation and maintenance procedures, and additional training. No reoccurrences of the problem have been observed since corrective actions were implemented.

Control rod driving hydraulic pressure device

International Nuclear Information System (INIS)

Ishida, Kazuo.

1990-01-01

Discharged water after actuating control rod drives in a BWR type reactor is once discharged to a discharging header, then returned to a master control unit and, subsequently, discharged to a reactor by way of a cooling water header. The radioactive level in the discharging header and the master control unit is increased by the reactor water to increase the operator's exposure. In view of the above, a riser is disposed for connecting a hydraulic pressure control unit incorporating a directional control valve and the cooling water head. When a certain control rod is inserted, the pressurized driving water is supplied through a hydraulic pressure control unit to the control rod drives. The discharged water from the control rod drives is entered by way of the hydraulic pressure control unit into the cooling water header and then returned to the reactor by way of other hydraulic pressure control unit and the control rod drives. Thus, the reactor water is no more recycled to the master control unit to reduce the radioactive exposure. (N.H.)

Nuclear reactor with scrammable part length rod

International Nuclear Information System (INIS)

Bevilacqua, F.

1979-01-01

A new part length rod is provided. It may be used to control xenon induced power oscillations but to contribute to shutdown reactivity when a rapid shutdown of the reactor is required. The part length rod consists of a control rod with three regions. The lower control region is a longer weaker active portion separated from an upper stronger shorter poison section by an intermediate section which is a relative non-absorber of neutrons. The combination of the longer weaker control section with the upper high worth poison section permits the part length rod of this to be scrammed into the core when a reactor shutdown is required but also permits the control rod to be used as a tool to control power distribution in both the axial and radial directions during normal operation

Apparatus for loading fuel pellets in fuel rods

International Nuclear Information System (INIS)

Tedesco, R.J.

1976-01-01

An apparatus is disclosed for loading fuel pellets into fuel rods for a nuclear reactor including a base supporting a table having grooves therein for holding a multiplicity of pellets. Multiple fuel rods are placed in alignment with grooves in the pellet table and a guide member channels pellets from the table into the corresponding fuel rods. To effect movement of pellets inside the fuel rods without jamming, a number of electromechanical devices mounted on the base have arms connected to the lower surface of the fuel rod table which cyclically imparts a reciprocating arc motion to the table for moving the fuel pellets longitudinally of and inside the fuel rods. These electromechanical devices include a solenoid having a plunger therein connected to a leaf type spring, the arrangement being such that upon energization of the solenoid coil, the leaf spring moves the fuel rod table rearwardly and downwardly, and upon deenergization of the coil, the spring imparts an upward-forward movement to the table which results in physical displacement of fuel pellets in the fuel rods clamped to the table surface. 8 claims, 6 drawing figures

High prevalence of turkey parvovirus in turkey flocks from Hungary experiencing enteric disease syndromes.

Science.gov (United States)

Palade, Elena Alina; Demeter, Zoltán; Hornyák, Akos; Nemes, Csaba; Kisary, János; Rusvai, Miklós

2011-09-01

Samples collected in 2008 and 2009, from 49 turkey flocks of 6 to 43 days in age and presenting clinical signs of enteric disease and high mortality, were tested by polymerase chain reaction and reverse transcription-polymerase chain reaction for the presence of viruses currently associated with enteric disease (ED) syndromes: astrovirus, reovirus, rotavirus, coronavirus, adenovirus, and parvovirus. Turkey astroviruses were found in 83.67% of the cases and turkey astrovirus 2 (TAst-2) in 26.53%. The investigations directly demonstrated the high prevalence of turkey parvovirus (TuPV) in 23 flocks (46.9%) experiencing signs of ED, making this pathogen the second most identified after astroviruses. Phylogenetic analysis on a 527 base pair-long region from the NS1 gene revealed two main clusters, a chicken parvovirus (ChPV) and a TuPV group, but also the presence of a divergent branch of tentatively named "TuPV-like ChPV" strains. The 23 Hungarian TuPV strains were separately positioned in two groups from the American origin sequences in the TuPV cluster. An Avail-based restriction fragment length polymorphism assay has also been developed for the quick differentiation of TuPV, ChPV, and divergent TuPV-like ChPV strains. As most detected enteric viruses have been directly demonstrated in healthy turkey flocks as well, the epidemiology of this disease complex remains unclear, suggesting that a certain combination of pathogens, environmental factors, or both are necessary for the development of clinical signs.

Control rod housing alignment and repair apparatus

International Nuclear Information System (INIS)

Dixon, R.C.; Deaver, G.A.; Punches, J.R.; Singleton, G.E.; Erbes, J.G.; Offer, H.P.

1991-01-01

This patent describes a welding a repair device for precisely locating and welding the position of the top of a control rod drive housing attached from a stub tube from a corresponding aperture and alignment pin in a core plate within a boiling water nuclear reactor, the welding and repair device. It comprises: a shaft, the shaft extending from the vicinity of the top of the control rod drive housing up to and through the aperture in the core plate; means for registering to the aperture and the alignment pin on the core plate; a fixture attached to the bottom end of the shaft for mating to the top of the control rod drive housing in precise mating relationship; the fixture attached to the bottom end of the shaft whereby the fixture, when mated to the control rod drove housing and the registering means when registered to the alignment pin and aperture on the core plate imparts to the shaft, and angularity between the top of the control rod drive housing and the hole in the core plate; a hollow cylinder, the cylinder mounted for depending and sealed support with respect to the shaft above, about and below the control rod drive housing top; the cylinder depending down below the control rod drive housing to an elevation below the top of the sub tube; a rotating welding apparatus with a welding head for dispensing weldment mounted for rotation with respect to the shaft; the welding head disposed at the juncture between the side of the control rod drive housing and the stub tube; and means for flooding the cylinder with gas whereby the cylinder may be lowered. flooded in a gas environment and effect a weld between the top of the stub tube and the control rod drive housing

Control rod housing alignment and repair method

International Nuclear Information System (INIS)

Dixon, R.C.; Deaver, G.A.; Punches, J.R.; Singleton, G.E.; Erbes, J.G.; Offer, H.P.

1992-01-01

This patent describes a method for underwater welding of a control rod drive housing inserted through a stub tube to maintain requisite alignment and elevation of the top of the control rod drive housing to an overlying and corresponding aperture in a core plate as measured by an alignment device which determines the relative elevation and angularity with respect to the aperture. It comprises providing a welding cylinder dependent from the alignment device such that the elevation of the top of the welding cylinder is in a fixed relationship to the alignment device and is gas-proof; pressurizing the welding cylinder with inert welding gas sufficient to maintain the interior of the welding cylinder dry; lowering the welding cylinder through the aperture in the core plate by depending the cylinder with respect to the alignment device, the lowering including lowering through and adjusting the elevation relationship of the welding cylinder to the alignment device such that when the alignment device is in position to measure the elevation and angularity of the new control rod drive housing, the lower distal end of the welding cylinder extends below the upper periphery of the stub where welding is to occur; inserting a new control rod drive housing through the stub tube and positioning the control rod drive housing to a predetermined relationship to the anticipated final position of the control rod drive housing; providing welding implements transversely rotatably mounted interior of the welding cylinder relative to the alignment device such that the welding implements may be accurately positioned for dispensing weldment around the periphery of the top of the stub tube and at the side of the control rod drive housing; measuring the elevation and angularity of the control rod drive housing; and dispensing weldment along the top of the stub tube and at the side of the control rod drive housing

Processing of poison rods with a view to disposal

International Nuclear Information System (INIS)

Bichet, R.; Charamathieu, A.; Lasseur, C.; Golicheff, I.; Pouteaux, M.

1979-01-01

In the core of the French 900 and 1300 MW reactors, a certain number of rods have to be processed as wastes, particularly the burnable poison rods used during reactor start-up (900 MW: 68 rods; 1300 MW: 96 rods). Several solutions are possible: cutting and conditionning in reactor pool; transfer of the poison rods to a cutting and conditionning facility; transfer of the poison rods and fuel assemblies to a storage area where they are cutted and stored. Each of these solutions are studied, the advantages and disadvantages being presented

Solar potential in Turkey

International Nuclear Information System (INIS)

Soezen, Adnan; Arcaklioglu, Erol

2005-01-01

Most of the locations in Turkey receive abundant solar-energy, because Turkey lies in a sunny belt between 36 deg. and 42 deg. N latitudes. Average annual temperature is 18 to 20 deg. C on the south coast, falls to 14-16 deg. C on the west coat, and fluctuates between 4 and 18 deg. C in the central parts. The yearly average solar-radiation is 3.6 kW h/m 2 day, and the total yearly radiation period is ∼2610 h. In this study, a new formulation based on meteorological and geographical data was developed to determine the solar-energy potential in Turkey using artificial neural-networks (ANNs). Scaled conjugate gradient (SCG), Pola-Ribiere conjugate gradient (CGP), and Levenberg-Marquardt (LM) learning algorithms and logistic sigmoid (logsig) transfer function were used in the networks. Meteorological data for last four years (2000-2003) from 12 cities (Canakkale, Kars, Hakkari, Sakarya, Erzurum, Zonguldak, Balikesir, Artvin, Corum, Konya, Siirt, and Tekirdag) spread over Turkey were used in order to train the neural-network. Meteorological and geographical data (latitude, longitude, altitude, month, mean sunshine-duration, and mean temperature) are used in the input layer of the network. Solar-radiation is in the output layer. The maximum mean absolute percentage error was found to be less than 3.832% and R 2 values to be about 99.9738% for the selected stations. The ANN models show greater accuracy for evaluating solar-resource possibilities in regions where a network of monitoring stations has not been established in Turkey. This study confirms the ability of the ANN to predict solar-radiation values accurately

Metacognition and Self-Regulated Learning in Predicting University Students' Academic Achievement in Turkey

Science.gov (United States)

Çetin, Baris

2017-01-01

The purpose of this study was to determine whether perceived levels of self-regulated learning and metacognition predicted the ultimate grade point average (GPA) attained by 206 female and 70 male college seniors (aged 21 to 27) finishing their elementary education teaching certification studies at a university in Turkey. Data regarding individual…

Failure position detection device for nuclear fuel rod

International Nuclear Information System (INIS)

Ishida, Takeshi; Higuchi, Shin-ichi; Ito, Masaru; Matsuda, Yasuhiko

1987-01-01

Purpose: To easily detect failure position of a nuclear fuel rod by relatively moving an air-tightly shielded detection portion to a fuel rod. Constitution: For detecting the failure position of a leaked fuel assembly, the fuel assembly is dismantled and a portion of withdrawn fuel rod is air-tightly sealed with an inspection portion. The inside of the inspection portion is maintained at a pressure-reduced state. Then, in a case if failed openings are formed at a portion sealed by the inspection portion in the fuel rod, FP gases in the fuel rod are released based on the reduced pressure and the FP gases are detected in the detection portion. Accordingly, by relatively moving the detection portion to the fuel rod, the failure position can be detected. (Yoshino, Y.)

Failure position detection device for nuclear fuel rod

Energy Technology Data Exchange (ETDEWEB)

Ishida, Takeshi; Higuchi, Shin-ichi; Ito, Masaru; Matsuda, Yasuhiko

1987-03-24

Purpose: To easily detect failure position of a nuclear fuel rod by relatively moving an air-tightly shielded detection portion to a fuel rod. Constitution: For detecting the failure position of a leaked fuel assembly, the fuel assembly is dismantled and a portion of withdrawn fuel rod is air-tightly sealed with an inspection portion. The inside of the inspection portion is maintained at a pressure-reduced state. Then, in a case if failed openings are formed at a portion sealed by the inspection portion in the fuel rod, FP gases in the fuel rod are released based on the reduced pressure and the FP gases are detected in the detection portion. Accordingly, by relatively moving the detection portion to the fuel rod, the failure position can be detected. (Yoshino, Y.).

Fuel followed control rod installation at AFRRI

International Nuclear Information System (INIS)

Moore, Mark; Owens, Chris; Forsbacka, Matt

1992-01-01

Fuel Followed Control Rods (FFCRs) were installed at the Armed Forces Radiobiology Research Institute's 1 MW TRIGA Reactor. The procedures for obtaining, shipping, and installing the FFCRs is described. As part of the FFCR installation, the transient rod drive was relocated. Core performance due to the addition of the fuel followed control rods is discussed. (author)

Solitary waves on nonlinear elastic rods. II

DEFF Research Database (Denmark)

Sørensen, Mads Peter; Christiansen, Peter Leth; Lomdahl, P. S.

1987-01-01

In continuation of an earlier study of propagation of solitary waves on nonlinear elastic rods, numerical investigations of blowup, reflection, and fission at continuous and discontinuous variation of the cross section for the rod and reflection at the end of the rod are presented. The results ar...... are compared with predictions of conservation theorems for energy and momentum....

The effect of different screw-rod design on the anti-rotational torque: a biomechanical comparison of three conventional screw-rod constructs.

Science.gov (United States)

Huang, Zifang; Wang, Chongwen; Fan, Hengwei; Sui, Wenyuan; Li, Xueshi; Wang, Qifei; Yang, Junlin

2017-07-28

Screw-rod constructs have been widely used to correct spinal deformities, but the effects of different screw-rod systems on anti-rotational torque have not been determined. This study aimed to analyze the biomechanical effect of different rod-screw constructs on anti-rotational torque. Three conventional spinal screw-rod systems (Legacy, RF-F-10 and USSII) were used to test the anti-rotational torque in the material test machine. ANOVA was performed to evaluate the anti-rotational capacity of different pedicle screws-rod constructs. The anti-rotational torque of Legacy group, RF-F-10 group and USSII group were 12.3 ± 1.9 Nm, 6.8 ± 0.4 Nm, and 3.9 ± 0.8 Nm, with a P value lower than 0.05. This results indicated that the Legacy screws-rod construct could provide a highest anti-rotation capacity, which is 68% and 210% greater than RF-F-10 screw-rod construct and USSII screw-rod respectively. The anti-rotational torque may be mainly affected by screw cap and groove design. Our result showed the anti-rotational torque are: Legacy system > RF-F-10 system > USSII system, suggesting that appropriate rod-screw constructs selection in surgery may be vital for anti-rotational torque improvement and preventing derotation correction loss.

Cutting system for burnable poison rod

International Nuclear Information System (INIS)

Shiina, Atsushi; Toyama, Norihide; Koshino, Yasuo; Fujii, Toshio

1989-01-01

Burnable poison rods attached to spent fuels are contained in a containing box and transported to a receiving pool. The burnable poison rod-containing box is provisionally situated by the operation to a handling device to a provisional setting rack in a cutting pool and attached to a cutting guide of a cutting device upon cutting. The burnable poison rod is cut only in a cutting pool water and tritium generated upon cutting is dissolved into the cutting pool water. Diffusion of tritium is thus restricted. Further, the cutting pool is isolated by a partition device from the receiving pool during cutting of the burnable poison rod. Accordingly, water in which tritium is dissolved is inhibited from moving to the receiving pool and prevail of tritium contamination can be avoided. (T.M.)

Brownian dynamics simulations with stiff finitely extensible nonlinear elastic-Fraenkel springs as approximations to rods in bead-rod models.

Science.gov (United States)

Hsieh, Chih-Chen; Jain, Semant; Larson, Ronald G

2006-01-28

A very stiff finitely extensible nonlinear elastic (FENE)-Fraenkel spring is proposed to replace the rigid rod in the bead-rod model. This allows the adoption of a fast predictor-corrector method so that large time steps can be taken in Brownian dynamics (BD) simulations without over- or understretching the stiff springs. In contrast to the simple bead-rod model, BD simulations with beads and FENE-Fraenkel (FF) springs yield a random-walk configuration at equilibrium. We compare the simulation results of the free-draining bead-FF-spring model with those for the bead-rod model in relaxation, start-up of uniaxial extensional, and simple shear flows, and find that both methods generate nearly identical results. The computational cost per time step for a free-draining BD simulation with the proposed bead-FF-spring model is about twice as high as the traditional bead-rod model with the midpoint algorithm of Liu [J. Chem. Phys. 90, 5826 (1989)]. Nevertheless, computations with the bead-FF-spring model are as efficient as those with the bead-rod model in extensional flow because the former allows larger time steps. Moreover, the Brownian contribution to the stress for the bead-FF-spring model is isotropic and therefore simplifies the calculation of the polymer stresses. In addition, hydrodynamic interaction can more easily be incorporated into the bead-FF-spring model than into the bead-rod model since the metric force arising from the non-Cartesian coordinates used in bead-rod simulations is absent from bead-spring simulations. Finally, with our newly developed bead-FF-spring model, existing computer codes for the bead-spring models can trivially be converted to ones for effective bead-rod simulations merely by replacing the usual FENE or Cohen spring law with a FENE-Fraenkel law, and this convertibility provides a very convenient way to perform multiscale BD simulations.

Exchange Rate Pass-Through in Turkey

OpenAIRE

Marco Rossi; Daniel Leigh

2002-01-01

In light of the strong correlation between exchange rate movements and domestic prices in Turkey, it is important to assess the impact of the exchange rate on domestic prices, in particular as Turkey moves to an inflation targeting regime. This paper uses a recursive vector autoregression model to investigate the impact of exchange rate movements on prices in Turkey. We find that (i) the impact of the exchange rate on prices is over after about a year, but is mostly felt in the first four mon...

The present status of safeguards in Turkey

International Nuclear Information System (INIS)

Yilmazer, A.; Yuecel, A.

2001-01-01

Republic of Turkey signed Non-Proliferation Treaty (NPT) in Vienna, Austria on January 28, 1969 and the Treaty was ratified by Turkish Parliament on March 29, 1979. International Atomic Energy Agency (IAEA) and Republic of Turkey signed the Safeguards Agreement on June 30, 1981. Turkey accepted the international safeguards administered by IAEA and at the same time its subsidiary arrangements and Facility attachments were enforced for all nuclear facilities as an Non-Nuclear-Weapon State party to NPT. Regulation on Nuclear Materials Accounting and Control, which was prepared in accordance with Agreement Between the Government of Turkey and IAEA for the application of Safeguard in Connection with the Treaty on NPT, has been put into force since it was published in Official Gazette on September 10, 1997. This study presents the essential futures of national system of accounting for and control of nuclear materials in Turkey

Four-point probe measurements of a direct current potential drop on layered conductive cylinders

International Nuclear Information System (INIS)

Lu, Yi; Bowler, John R

2012-01-01

We have determined the steady state electric field due to direct current flowing via point contacts at the cylindrical surface of a uniformly layered conductive rod of finite length. The solution allows one to use four-point probe potential drop measurements to estimate the conductivity or thickness of the layer assuming that the other parameters are known. The electrical potential in the rod has a zero radial derivative at its surface except at the injection and extractions points. This means that the required solution can be expressed in terms of a Green’s function satisfying a Neumann boundary condition. Four-point measurements have been made to demonstrate the validity of theoretical results. (paper)

Four-point probe measurements of a direct current potential drop on layered conductive cylinders

Science.gov (United States)

Lu, Yi; Bowler, John R.

2012-11-01

We have determined the steady state electric field due to direct current flowing via point contacts at the cylindrical surface of a uniformly layered conductive rod of finite length. The solution allows one to use four-point probe potential drop measurements to estimate the conductivity or thickness of the layer assuming that the other parameters are known. The electrical potential in the rod has a zero radial derivative at its surface except at the injection and extractions points. This means that the required solution can be expressed in terms of a Green’s function satisfying a Neumann boundary condition. Four-point measurements have been made to demonstrate the validity of theoretical results.

Damage analysis of ceramic boron absorber materials in boiling water reactors and initial model for an optimum control rod management

International Nuclear Information System (INIS)

Schulz, W.

2000-01-01

Operating experience has proved so far that BWR control rods cannot be used for the total reactor life time as originally presumed, but instead has to be considered as a consumable article. After only few operating cycles, the mechanism of absorber failure has been shown to be neutron induced boron carbide swelling and stress cracking of the absorber tubes, followed by erosion of the absorber material. In the case that operation of such a control rod is continued in control cells, this can lead to an increase of the local power density distribution in the core and, under certain conditions, can even cause fuel rod damage. A non destructive testing method has been developed called 'UNDERWATER NEUTRON RADIOGRAPHY' applicable for any BWR control rod. 'Lead-control rods' being radiographed are used to evaluate their actual nuclear worth by the help of a special analytical procedure developed and verified by the author. Nuclear worth data plotted against bum up history data will allow to create an 'EMPIRIC MODEL'. This model includes the basic idea of operating control rods of a certain design first in a control position up to a target fluence limited to an amount just below the appearance of control rod washout. Afterwards they have to be moved in a shut down position to work therefor the total remaining holding period. The initial model is applicable to any CR-design as long as sufficient measuring-data and thus data about the nuclear worth are available. The results of these experiences are extrapolated to the whole reactor holding period. After modelling no further measurements of this particular control rod type are necessary in any reactor. The second focal point is to provide an APPROXIMATION EQUATION. By knowing the absorber radius, B 4 C density and absorber enclosure data an engineer will calculate reliably the working life of any control rod design on control position. indicated as maximum allowable neutron fluence margin until absorber wash-out starts. This

Analysis of buffering process of control rod hydraulic absorber

International Nuclear Information System (INIS)

Bao Jishi; Qin Benke; Bo Hanliang

2011-01-01

Control Rod Hydraulic Drive Mechanism(CRHDM) is a newly invented build-in control rod drive mechanism. Hydraulic absorber is the key part of this mechanism, and is used to cushion the control rod when the rod scrams. Thus, it prevents the control rod from being deformed and damaged. In this paper dynamics program ANSYS CFX is used to calculate all kinds of flow conditions in hydraulic absorber to obtain its hydraulic characteristics. Based on the flow resistance coefficients obtained from the simulation results, fluid mass and momentum equations were developed to get the trend of pressure change in the hydraulic cylinder and the displacement of the piston rod during the buffering process of the control rod. The results obtained in this paper indicate that the hydraulic absorber meets the design requirement. The work in this paper will be helpful for the design and optimization of the control rod hydraulic absorber. (author)

Control rod experiments in Racine

International Nuclear Information System (INIS)

Stanculescu, A.; Humbert, G.

1981-09-01

A survey of the control-rod experiments planned within the joint CEA/CNEN-DeBeNe critical experiment RACINE is given. The applicability to both heterogeneous and homogeneous large power LMFBR-cores is discussed. Finally, the most significant results of the provisional design calculations performed on behalf of the RACINE control-rod programme are presented

Basic design in architectural education in Turkey

Directory of Open Access Journals (Sweden)

Makaklı Elif Süyük

2016-01-01

Full Text Available Creative activity is one of the most significant parts of architectural education. In the architectural curriculum organisation ‘design studio’ is the unique and preeminent subject. Freshman students encounter ‘design’ first in basic design course, before they know what designing incorporates. The Basic Design is the starting point of initiating creativity in architecture education. It helps each student to understand architecture as a creative and innovative practice in the first year of education. This study analyzes the characteristics of basic design course, the topics of the course contents and its significance in the architectural curriculum in Turkey as well.

INDIAN POINT REACTOR STARTUP AND PERFORMANCE

Energy Technology Data Exchange (ETDEWEB)

Deddens, J. C.; Batch, M. L.

1963-09-15

The testing program for the Indian Point Reactor is discussed. The thermal and hydraulic evaluation of the primary coolant system is discussed. Analyses of fuel loading and initial criticality, measurement of operating coefficients of reactivity, control rod group reactivity worths, and xenon evaluation are presented. (R.E.U.)

Sales Forecasting System for Newspaper Distribution Companies in Turkey

Directory of Open Access Journals (Sweden)

Gencay İncesu

2012-07-01

Full Text Available Normal 0 false false false EN-US X-NONE X-NONE st1\\:*{behavior:url(#ieooui } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif";} Newspapers are like goods with a shelf life of one day and they have to be distributed daily basis to the sales points. A problem that most newspaper companies encounter daily is how to predict the right number of newspapers to print and distribute among distinct sales points. The aim is to predict newspaper demand as accurately as possible to meet customer need with minimum number of returns, missed sales and oversupply. This makes it necessary to develop a short-term forecasting system. The data taken from one of the largest distribution companies in Turkey is time dependent. Therefore, time series analysis is used to forecast newspaper circulation. In this paper, the newspaper sales system is examined for Turkey. Various types of forecasting techniques which are applicable to newspaper circulation planning are compared and a nonlinear approach for returns is applied.

RODMOD: a code for control rod positioning

International Nuclear Information System (INIS)

Vondy, D.R.; Fowler, T.B.

1978-11-01

The report documents a computer code which has been implemented to position control rods according to a prescribed schedule during the calculation of a reactor history. Control rods may be represented explicitly with or without internal black absorber conditions in selected energy groups, or fractional insertion may be done, or both, in a problem. There is provision for control rod follower, movement of materials through a series of zones in a closed loop, and shutdown rod insertion and subsequent removal to allow the reactor history calculation to be continued. This code is incorporated in the system containing the VENTURE diffusion theory neutronics and the BURNER exposure codes for routine use. The implemented automated procedures cause the prescribed control rod insertion schedule to be applied without the access of additional user input data during the calculation of a reactor operating history

Analysis of rod drop and pulsed source measurements of reactivity in the Winfrith SGHWR

International Nuclear Information System (INIS)

Brittain, I.

1970-05-01

Reactivity measurements by the rod-drop and pulsed source methods in the Winfrith SGHWR are seriously affected by spatial harmonics. A method of calculation is described which enables the spatial harmonics to be calculated in non-uniform cores in two or three dimensions, and thus allows a much more rigorous analysis of the experimental results than the usual point model. The method is used to analyse all the rod-drop measurements made during commissioning of the Winfrith SGHWR, and to comment on the results of pulsed source measurements. The reactivity worths of banks of ten and twelve shut-down tubes deduced from rod-drop and pulsed source experiments are in satisfactory agreement with each other and also with AIMAZ calculated values. The ability to calculate higher spatial harmonics in nonuniform cores is thought to be new, and may have a wider application to reactor kinetics through the method of Modal Analysis. (author)

Creating Helical Tool Paths for Single Point Incremental Forming

DEFF Research Database (Denmark)

Skjødt, Martin; Hancock, Michael H.; Bay, Niels

2007-01-01

Single point incremental forming (SPIF) is a relatively new sheet forming process. A sheet is clamped in a rig and formed incrementally using a rotating single point tool in the form of a rod with a spherical end. The process is often performed on a CNC milling machine and the tool movement...

French LMFBR's control rods experience and development

International Nuclear Information System (INIS)

Arnaud, G.; Guigon, A.; Verset, L.

1983-06-01

Since the last ten years, the French program has been, first of all, directed to the setting up, and then the development of, at once, the Phenix control rods, and next, the Super-Phenix ones. The vented pin design, with porous plug and sodium bonding, which allows the choices of large diameters, has been taken, since the Rapsodie experience was decisive. The absorber material is sintered, 10 B enriched, boron carbide. The can is made of 316 type stainless steel, stabilised, or not, with titanium. The experience gained in Phenix up to now is important, and deals with about six loads of control rods. Results confirm the validity of the design of the absorber pins. Some difficulties has been encountered for the guiding devices, due to the swelling of the steel. They have required design and material improvements. Such difficulties are discarded by a new design of the bearing, for the Super-Phenix control rods. The other parts of these rods, from the Primary Shut-Down System, are strictly derived from Phenix. The design of the rods from the Secondary Shut-Down System is rather different, but it's not the case for the design of the absorber pins: in many a way, they are derived from Phenix pins and from Rapsodie control rods. Both types of rods irradiation tests are in progress in Phenix [fr

Advanced gray rod control assembly

Science.gov (United States)

Drudy, Keith J; Carlson, William R; Conner, Michael E; Goldenfield, Mark; Hone, Michael J; Long, Jr., Carroll J; Parkinson, Jerod; Pomirleanu, Radu O

2013-09-17

An advanced gray rod control assembly (GRCA) for a nuclear reactor. The GRCA provides controlled insertion of gray rod assemblies into the reactor, thereby controlling the rate of power produced by the reactor and providing reactivity control at full power. Each gray rod assembly includes an elongated tubular member, a primary neutron-absorber disposed within the tubular member said neutron-absorber comprising an absorber material, preferably tungsten, having a 2200 m/s neutron absorption microscopic capture cross-section of from 10 to 30 barns. An internal support tube can be positioned between the primary absorber and the tubular member as a secondary absorber to enhance neutron absorption, absorber depletion, assembly weight, and assembly heat transfer characteristics.

Refabricated and instrumented fuel rods

International Nuclear Information System (INIS)

Silberstein, K.

2005-01-01

Nuclear Fuel for power reactors capabilities evaluation is strongly based on the intimate knowledge of its behaviour under irradiation. This knowledge can be acquired from refabricated and instrumented fuel rods irradiated at different levels in commercial reactors. This paper presents the development and qualification of a new technique called RECTO related to a double-instrumented rod re-fabrication process developed by CEA/LECA hot laboratory facility at CADARACHE. The technique development includes manufacturing of the properly dimensioned cavity in the fuel pellet stack to house the thermocouple and the use of a newly designed pressure transducer. An analytic irradiation of such a double-instrumented fuel rod will be performed in OSIRIS test reactor starting October 2004. (Author)

Reactor control rod supporting structure

International Nuclear Information System (INIS)

Akimoto, Tokuzo; Miyata, Hiroshi.

1984-01-01

Purpose: To enable stable reactor core control even in extremely great vertical earthquakes, as well as under normal operation conditions in FBR type reactors. Constitution: Since a mechanism for converting the rotational movement of a control rod into vertical movement is placed at the upper portion of the reactor core at high temperature, the mechanism should cause fusion or like other danger after the elapse of a long period of time. In view of the above, the conversion mechanism is disposed to the lower portion of the reactor core at a lower temperature region. Further, the connection between the control rod and the control rod drive can be separated upon great vertical earthquakes. (Seki, T.)

Energy efficiency in the world and Turkey and investigation of energy efficiency in Turkish Industry

International Nuclear Information System (INIS)

Kavak, K.

2005-09-01

The reserves of fossil fuels which currently respond to the major part of world energy requirements are being running out very fast. Because it is forecasted that reserves of some fossil fuels like oil and natural gas will come to an end in the second half of this century, exploiting all energy resources in an efficient manner has great importance. Throughout the world where the energy demand grows continuously but the resources decrease gradually, many types of programs are implemented to provide efficient energy use. In Turkey, although there have been some efforts in last two decades, the importance of the issue could not be undersood yet. Turkey'sgeneral energy policy still focuses on supply security and finding ways to meet the growing demand, rather than decreasing the demand by energy efficiency. In this study, the possible opportunities and benefits that Turkey would gain by energy efficiency is pointed out. The studies about energy efficiency which have been conducted in the world and Turkey are examined. The measurement that can be taken in the sectors such as industry, power plants, buildings, transportation and the utilities of these measures for energy economy are indicated. The successful practices of energy efficiency studies in various countries, the state of some countries which pioneer efficiency implementations. Turkey's situation in energy in the light of basic indicators such as energy consumption per capita and enrgy intensity, the energy efficiency studies that have been done and should be done in various sectors of Turkey are also discussed in this thesis. Turkish industry's energy comsumption is analyzed as a seperate chapter by taking into consideration energy efficiency, energy intensity and energy resources. The general energy consumption and energy intensity tendencies of main manufacturing industries between 1995 and 2002 are explored and resource utilization ratios are investigated. This chapter provides to find out what kind of

Thalassemias and hemoglobinopathies in Turkey.

Science.gov (United States)

Canatan, Duran

2014-01-01

Thalassemias and hemoglobinopathies are a serious health problem in Turkey. There is a 70-year history of thalassemia in Turkey. The first patient with β-thalassemia major (β-TM) was reported in 1941. The first clinical and hematological studies were published by Aksoy in 1958. The overall incidence of β-thalassemia (β-thal) was reported by Çavdar and Arcasoy to be 2.1% in 1971. Important steps such as written regulations, education and prevention campaigns, have been taken to prevent thalassemia in Turkey by the Ministry of Health (MOH), the Turkish National Hemoglobinopathy Council (TNHC) and the Thalassemia Federation of Turkey (TFT) since 2000. A national hemoglobinopathy prevention program was started in provinces with a high prevalence by the MOH in 2003. While the percentage of premarital screening test was 30.0% of all couples in 2003, it reached 86.0% in 2013. While the number of newborn with thalassemias and hemoglobinopathies was 272 in 2002, it had dropped to 25 in 2010. There has been a 90.0% reduction of affected births in the last 10 years.

Secondary hydriding of defected zircaloy-clad fuel rods

International Nuclear Information System (INIS)

Olander, D.R.; Vaknin, S.

1993-01-01

The phenomenon of secondary hydriding in LWR fuel rods is critically reviewed. The current understanding of the process is summarized with emphasis on the sources of hydrogen in the rod provided by chemical reaction of water (steam) introduced via a primary defect in the cladding. As often noted in the literature, the role of hydrogen peroxide produced by steam radiolysis is to provide sources of hydrogen by cladding and fuel oxidation that are absent without fission-fragment irradiation of the gas. Quantitative description of the evolution of the chemical state inside the fuel rod is achieved by combining the chemical kinetics of the reactions between the gas and the fuel and cladding with the transport by diffusion of components of the gas in the gap. The chemistry-gas transport model provides the framework into which therate constants of the reactions between the gases in the gap and the fuel and cladding are incorporated. The output of the model calculation is the H 2 0/H 2 ratio in the gas and the degree of claddingand fuel oxidation as functions of distance from the primary defect. This output, when combined with a criterion for the onset of massive hydriding of the cladding, can provide a prediction of the time and location of a potential secondary hydriding failure. The chemistry-gas transport model is the starting point for mechanical and H-in-Zr migration analyses intended to determine the nature of the cladding failure caused by the development of the massive hydride on the inner wall

Age-related deterioration of rod vision in mice.

Science.gov (United States)

Kolesnikov, Alexander V; Fan, Jie; Crouch, Rosalie K; Kefalov, Vladimir J

2010-08-18

Even in healthy individuals, aging leads to deterioration in visual acuity, contrast sensitivity, visual field, and dark adaptation. Little is known about the neural mechanisms that drive the age-related changes of the retina and, more specifically, photoreceptors. According to one hypothesis, the age-related deterioration in rod function is due to the limited availability of 11-cis-retinal for rod pigment formation. To determine how aging affects rod photoreceptors and to test the retinoid-deficiency hypothesis, we compared the morphological and functional properties of rods of adult and aged B6D2F1/J mice. We found that the number of rods and the length of their outer segments were significantly reduced in 2.5-year-old mice compared with 4-month-old animals. Aging also resulted in a twofold reduction in the total level of opsin in the retina. Behavioral tests revealed that scotopic visual acuity and contrast sensitivity were decreased by twofold in aged mice, and rod ERG recordings demonstrated reduced amplitudes of both a- and b-waves. Sensitivity of aged rods determined from single-cell recordings was also decreased by 1.5-fold, corresponding to not more than 1% free opsin in these photoreceptors, and kinetic parameters of dim flash response were not altered. Notably, the rate of rod dark adaptation was unaffected by age. Thus, our results argue against age-related deficiency of 11-cis-retinal in the B6D2F1/J mouse rod visual cycle. Surprisingly, the level of cellular dark noise was increased in aged rods, providing an alternative mechanism for their desensitization.

Optimized Control Rods of the BR2 Reactor

Energy Technology Data Exchange (ETDEWEB)

Kalcheva, Silva; Koonen, E.

2007-09-15

At the present time the BR-2 reactor uses control elements with cadmium as neutron absorbing part. The lower section of the control element is a beryllium assembly cooled by light water. Due to the burn up of the lower end of the cadmium section during the reactor operation, the presently used rods for reactivity control of the BR-2 reactor have to be replaced by new ones. Considered are various types Control Rods with full active part of the following materials: cadmium (Cd), hafnium (Hf), europium oxide (Eu2O3) and gadolinium (Gd2O3). Options to decrease the burn up of the control rod material in the hot spot, such as use of stainless steel in the lower active part of the Control Rod are discussed. Comparison with the characteristics of the presently used Control Rods types is performed. The changing of the characteristics of different types Control Rods and the perturbation effects on the reactor neutronics during the BR-2 fuel cycle are investigated. The burn up of the Control Rod absorbing material, total and differential control rods worth, macroscopic and effective microscopic absorption cross sections, fuel and reactivity evolution are evaluated during approximately 30 operating cycles.

Control rod repositioning considerations in core design analysis

International Nuclear Information System (INIS)

Armstrong, B.C.; Buechel, R.J.

1990-01-01

Control rod repositioning is a method for minimizing rod cluster control assembly (RCCA) wear in the upper internals area where the guide cards interface with the rodlets of the RCCAs. A number of utilities have implemented strategies for rod repositioning, which often has no impact on the nuclear analysis for cases where the control rods are never repositioned into the active fuel. Other strategies involve repositioning the control rods several steps into the active fuel. The impact of this type of repositioning on the axial power shape and consequently the total peaking factor F Q T varies, depending on the method in which the repositioning is implemented at the plant. Operating for long periods with all the control and shutdown rods inserted several steps in the active fuel followed by withdrawing them fully from the core results in a shifting of the power distribution toward the top of the core and must be accounted for in the design analysis. On the other hand, an optional plan for control rod repositioning that considers margins available in related design parameters can be devised that minimizes the effects of the repositioning for the reload. This paper summarizes a rod repositioning strategy implemented for a recent reload and some calculated power shape results for this strategy and other scenarios

Optimized Control Rods of the BR2 Reactor

International Nuclear Information System (INIS)

Kalcheva, Silva; Koonen, E.

2007-01-01

At the present time the BR-2 reactor uses control elements with cadmium as neutron absorbing part. The lower section of the control element is a beryllium assembly cooled by light water. Due to the burn up of the lower end of the cadmium section during the reactor operation, the presently used rods for reactivity control of the BR-2 reactor have to be replaced by new ones. Considered are various types Control Rods with full active part of the following materials: cadmium (Cd), hafnium (Hf), europium oxide (Eu2O3) and gadolinium (Gd2O3). Options to decrease the burn up of the control rod material in the hot spot, such as use of stainless steel in the lower active part of the Control Rod are discussed. Comparison with the characteristics of the presently used Control Rods types is performed. The changing of the characteristics of different types Control Rods and the perturbation effects on the reactor neutronics during the BR-2 fuel cycle are investigated. The burn up of the Control Rod absorbing material, total and differential control rods worth, macroscopic and effective microscopic absorption cross sections, fuel and reactivity evolution are evaluated during approximately 30 operating cycles.

Conceptual design report of the SMART fuel rod

Energy Technology Data Exchange (ETDEWEB)

Kim, Dae Ho; Lee, Chan Bock; Bang, Je Gun; Jung, Yeon Ho [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-03-01

The SMART fuel rod is based on 17 x 17 KOFA(Korea Fuel Assembly) fuel rod of the 950MWe pressurize water reactor. The fuel stack length of the KOFA is 3658mm, otherwise SMART fuel rod stack length is 2000mm. The fuel rod contains UO{sub 2} pellets with the enrichment of 4.95%. All the fuel in core will be replaced every 35 months. The average LHGR of the fuel rod is 120 W/cm, commercial PWR is 178 W/cm, SMART LHGR is lower about 31% than commercial PWR. The core inlet and outlet temperature of coolant are respectively 270 deg C and 310 deg C, commercial PWR are respectively 291.6 deg C and 326.8 deg C, SMART inlet and outlet temperature is lower averaged 19.2 deg C than commercial PWR. The coolant use mixed soluble ammonia in high purity water and boron is not in. The general performance of the fuel rod UO{sub 2} pellet has been already verified through the sufficient burnup (60,000 MWd/MTU-rod avg.) experience as the rods of same design in commercial PWR's. But cladding corrosion is required the further verification. (author). 13 refs., 3 figs., 8 tabs.

PARASITIC MITES IN BACKYARD TURKEYS

Directory of Open Access Journals (Sweden)

Marco Antonio Camacho-Escobar

2010-02-01

Full Text Available To describe the parasitic mites in backyard turkeys, was did this work. The mites were obtain by hand for 30 backyard turkeys in Oaxaca’s Coast region, Mexico; the mites were mount in adhesive paper and wash with the 200X lent in a computer optical microscopy, the parasites size were determinate in the pictures obtained by the microscopy software, the images were sized using a specialist software for it, which relate the number of pixels in the picture with the size of the observation field. Were indentified the species Dermanyssus gallinae, Megninia ginglymura and Ornithonyssus sylviarum, the last two described for first time in backyard turkeys in Mexico. Â

Results from In-pile experiments on LWR fuel rod behavior under LOCA conditions with unirradiated rods

International Nuclear Information System (INIS)

Sepold, L.; Karb, E.H.; Pruessmann, M.

1981-06-01

This report summarizes the results of the FR2-in-pile tests at KfK (Kernforschungszentrum Karlsruhe) with unirradiated test rods. The in-pile tests with the objective of investigating the influence of a nuclear environment on the mechanisms of fuel rod failure were being performed with irradiated and unirradiated single rods of a PWR design in the DK loop of the FR2 reactor. The main parameter of the test program was the burnup, ranging from 2.500 to 35.000 MWd/t. The program with unirradiated specimens comprised the series A and B with a total of 14 tests. (orig.) [de

CONNECTING THE ENLARGEMENT PROCESS WITH THE EUROPEANIZATION THEORY (THE CASE OF TURKEY

Directory of Open Access Journals (Sweden)

Teodor Lucian Moga

2010-03-01

Full Text Available Europeanization is one of the theoretical instruments which had a vital influence on candidate countries for EU membership. Due to its aspirations of becoming member of the European Union (EU and in its attempt to fulfil the Copenhagen criteria, Turkey is trying to comply with the EU acquis communautaire. The aim of this paper is to assess the effects of the Europeanization process on the countries subject to EU enlargement strategy, with a special focus on Turkey, particularly since the country received the EU candidate status in 1999. This paper has been organized in the following way: firstly, it points out how both the traditional Europeanization and the enlargement led Europeanization have been depicted in the work of several important scholars; secondly, by offering a short overview of Turkey’s foreign relations vis-à-vis its neighbourhood, especially in the last decade, it examines how the mechanism of Europeanization largely influenced the country’s diplomatic culture. Traditionally, Turkey has been attuned to hard security issues and architectures. However, the Turkish foreign policy strategy emphasised in thepast years the Venus side of things in many settings in line with EU requirements.

Air-water two-phase flow in a four by four rod bundle with partial length rods

International Nuclear Information System (INIS)

Ohta, Motoki; Kamei, Akihiro; Mizutani, Yoshitaka; Hosokawa, Shigeo; Tomiyama, Akio

2009-01-01

Partial length rods (PLR) are used in fuel bundles of BWR to reduce pressure drops in two-phase regions and to optimize the power distribution. Since little is known about effects of PLR on two-phase flows, air-water two-phase flow around PLRs in a four by four rod bundle is visualized by using a high-speed video camera. The experimental apparatus consists of acrylic channel box and transparent rods. Air and water at atmospheric pressure and room temperature are used for the gas and liquid phases, respectively. The ranges of the gas and liquid volume fluxes, J G and J L , are 0.4 L G L , the flow pattern in the downstream of PLR transits to slug flow, and the flow patterns in the surrounding subchannels transit to bubbly flow due to the redistribution of gas flow. (2) In annular flow, the liquid film on the PLR forms a liquid column above the end cap of PLR. Droplets are generated by column breakup and deposit on liquid films on the neighboring rods. (3) The liquid film thickness on the surface of neighbor rods facing the PLR increases and it reduces that on their opposite surface in the downstream of PLR. (author)

Development of design technology on thermal-hydraulic performance in tight-lattice rod bundle. III - Numerical estimation on rod bowing effect based on X-ray CT data

International Nuclear Information System (INIS)

Misawa, Takeharu; Ohnuki, Akira; Katsuyama, Kozo; Nagamine, Tsuyoshi; Nakamura, Yasuo; Akimoto, Hajime; Mitsutake, Toru; Misawa, Susumu

2007-01-01

Design studies of the Innovative Water Reactor for Flexible Fuel Cycle (FLWR) are being carried out at the Japan Atomic Energy Agency (JAEA) as one candidate for the future reactors. In actual core design, it is precondition to prevent fuel rods contact due to fuel rod bowing. However, the FLWR cores have nonconventional characteristics such as a hexagonal tight lattice arrangement and a high enrichment fuel loading. Therefore, as conservative evaluation, it is important to investigate influence of fuel rod bowing upon the boiling transition. In the JAEA, a 37-rod bundle experiments (base case test section (1.3mm gap width), gap width effect test section (1.0mm gap width), and rod bowing test section) were performed in order to investigate the thermal hydraulic characteristics in the tight lattice bundle. In this paper, the rod bowing effect test is paid attention. It is suspected that the actual fuel rod positions in the rod bowing test section may be different from the design-based positions. Even a slight displacement from the design-based position of fuel rod may occur variation of flow area, and give influence upon the thermal hydraulic characteristics in the rod bundle. Therefore, if the critical power in the rod bundle is evaluated by an analytical approach, the analysis based on more correct input can be performed by using actual fuel rod position data. In this study, the rod positions in the rod bowing test section were measured using the high energy X-ray computer tomography (Xray-CT). Based on the measured rod positions data, the subchannel analysis by the NASCA code was performed, in order to investigate applicability of the NASCA code to BT estimation of the rod bowing test section, and influence of displacement from design-based rod position upon BT estimation by the NASCA code. The predicted critical powers are agreement with those obtained by the experiment. The analysis based on the design-based rod positions is also performed, and the result is

Management of radioactive disused lightning rods

Energy Technology Data Exchange (ETDEWEB)

Santos, Paulo de Oliveira; Silva, Fabio, E-mail: pos@cdtn.br, E-mail: silvaf@cdtn.br [Centro de Desenvolvimento da Energia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2013-07-01

The manufacture of radioactive lightning rod was allowed from 1970 to 1989. This authorization was based on state-of-the art science of that time that verified that radioactive lightning rods had efficiency superior to the conventional lightning rods, denominated Franklin. However, the experience showed that their efficiency was not superior enough to justify the use of radioactive sources. Consequently, in 1989, the National Commission or Nuclear Energy - CNEN, issued the Resolution 04/89 from 04-19-1989, that forbidden the importation of {sup 241}Am tapes, assembling and commercialization of radioactive lightning-rods. The institutes of CNEN are responsible for receiving these lightning-rods and sending to the users procedures for removing and dispatch to the institutes. Therewith, these devices are kept away from the human being and environment. The Nuclear technology Development Center - CDTN and Institute for Energy and Nuclear Research - IPEN of CNEN, has built laboratories appropriate for dismantling such devices and store the {sup 241}Am tapes safely. Nowadays are being researched methodologies to evaluate the contamination levels of the frame for possible recycling and become better the management of these devices. (author)

Management of radioactive disused lightning rods

International Nuclear Information System (INIS)

Santos, Paulo de Oliveira; Silva, Fabio

2013-01-01

The manufacture of radioactive lightning rod was allowed from 1970 to 1989. This authorization was based on state-of-the art science of that time that verified that radioactive lightning rods had efficiency superior to the conventional lightning rods, denominated Franklin. However, the experience showed that their efficiency was not superior enough to justify the use of radioactive sources. Consequently, in 1989, the National Commission or Nuclear Energy - CNEN, issued the Resolution 04/89 from 04-19-1989, that forbidden the importation of 241 Am tapes, assembling and commercialization of radioactive lightning-rods. The institutes of CNEN are responsible for receiving these lightning-rods and sending to the users procedures for removing and dispatch to the institutes. Therewith, these devices are kept away from the human being and environment. The Nuclear technology Development Center - CDTN and Institute for Energy and Nuclear Research - IPEN of CNEN, has built laboratories appropriate for dismantling such devices and store the 241 Am tapes safely. Nowadays are being researched methodologies to evaluate the contamination levels of the frame for possible recycling and become better the management of these devices. (author)

Hot spot in GdBa2Cu3O7-δ-based composite ceramics rods and their applications for oxygen sensors

International Nuclear Information System (INIS)

Okamoto, T; Takata, M

2011-01-01

A hot spot, which is a local area glowing orange, appears in a LnBa 2 Cu 3 O 7-δ (Ln: rare earth element) ceramic rod when a voltage exceeding a certain value is applied to the rod at room temperature. After the appearance of the hot spot, the current changes according to the oxygen partial pressure in ambient atmosphere, which acts as an oxygen sensor without the need for any heating system. The GdBa 2 Cu 3 O 7-δ rod tended to be melted and broken by a sustained presence of the hot spot in a high oxygen partial pressure Po 2 (∼100 kPa). The composite rod containing high melting point materials, such as BaAl 2 O 4 , BaZrO 3 and Gd 2 BaCuO 5 , showed a remarkable high durability in O 2 atmosphere. In a low Po 2 ( 2 Cu3O 7-δ rod decreases to almost zero and the hot spot disappeared, resulting in an insensitive rod to oxygen. The composite rod containing CuO detected oxygen even in Po 2 < 0.002 kPa.

Stabilizing device for control rod tip

International Nuclear Information System (INIS)

Verdone, G.F.

1982-01-01

A control rod has a spring device on its lower end for eliminating oscillatory contact of the rod against its adjacent guide tube wall. The base of the device is connected to the lower tip of the rod. A plurality of elongated extensions are cantilevered downward from the base. Each extension has a shoulder for contacting the guide tube, and the plurality of shoulders as a group has a transverse dimension that is preset to be larger than the inner diameter of the guide tube such that an interference fit is obtained when the control rod is inserted in the tube. The elongated extensions form an open-ended, substantially hollow member through which most of the liquid coolant flows, and the spaces between adjacent extensions allow the flow to bypass the shoulders without experiencing a significant pressure drop

Detection device for control rod scram

International Nuclear Information System (INIS)

Ishiyama, Satoshi.

1989-01-01

The device of the present invention comprises a control rod dropping separately from a control rod driving mechanism main body, a following tube falling separately accompanying therewith and a guide tube for guiding the dropping of the control rod and the following tube. Further, rare earth permanent magnets are embedded with the pole being axially oriented in the following tube and bobbins each mounted with an inner flange made of high magnetic permeability material are disposed to the guide tube. Coils are wound in the bobbin. In this control rod scram detection device, since magnetic fluxes can effectively be supplied to the coils, it is possible to obtain stable and highly reliable scram detection signals. Further, since the coils and the bobbins can be manufactured separately from the guide tube, their assemblies can be tested independently from the guide tube. (K.M.)

Analysis of control rod behavior based on numerical simulation

International Nuclear Information System (INIS)

Ha, D. G.; Park, J. K.; Park, N. G.; Suh, J. M.; Jeon, K. L.

2010-01-01

The main function of a control rod is to control core reactivity change during operation associated with changes in power, coolant temperature, and dissolved boron concentration by the insertion and withdrawal of control rods from the fuel assemblies. In a scram, the control rod assemblies are released from the CRDMs (Control Rod Drive Mechanisms) and, due to gravity, drop rapidly into the fuel assemblies. The control rod insertion time during a scram must be within the time limits established by the overall core safety analysis. To assure the control rod operational functions, the guide thimbles shall not obstruct the insertion and withdrawal of the control rods or cause any damage to the fuel assembly. When fuel assembly bow occurs, it can affect both the operating performance and the core safety. In this study, the drag forces of the control rod are estimated by a numerical simulation to evaluate the guide tube bow effect on control rod withdrawal. The contact condition effects are also considered. A full scale 3D model is developed for the evaluation, and ANSYS - commercial numerical analysis code - is used for this numerical simulation. (authors)

A simple method for in vivo measurement of implant rod three-dimensional geometry during scoliosis surgery.

Science.gov (United States)

Salmingo, Remel A; Tadano, Shigeru; Fujisaki, Kazuhiro; Abe, Yuichiro; Ito, Manabu

2012-05-01

Scoliosis is defined as a spinal pathology characterized as a three-dimensional deformity of the spine combined with vertebral rotation. Treatment for severe scoliosis is achieved when the scoliotic spine is surgically corrected and fixed using implanted rods and screws. Several studies performed biomechanical modeling and corrective forces measurements of scoliosis correction. These studies were able to predict the clinical outcome and measured the corrective forces acting on screws, however, they were not able to measure the intraoperative three-dimensional geometry of the spinal rod. In effect, the results of biomechanical modeling might not be so realistic and the corrective forces during the surgical correction procedure were intra-operatively difficult to measure. Projective geometry has been shown to be successful in the reconstruction of a three-dimensional structure using a series of images obtained from different views. In this study, we propose a new method to measure the three-dimensional geometry of an implant rod using two cameras. The reconstruction method requires only a few parameters, the included angle θ between the two cameras, the actual length of the rod in mm, and the location of points for curve fitting. The implant rod utilized in spine surgery was used to evaluate the accuracy of the current method. The three-dimensional geometry of the rod was measured from the image obtained by a scanner and compared to the proposed method using two cameras. The mean error in the reconstruction measurements ranged from 0.32 to 0.45 mm. The method presented here demonstrated the possibility of intra-operatively measuring the three-dimensional geometry of spinal rod. The proposed method could be used in surgical procedures to better understand the biomechanics of scoliosis correction through real-time measurement of three-dimensional implant rod geometry in vivo.

Nuclear fuel rod end plug weld inspection

International Nuclear Information System (INIS)

Parker, M. A.; Patrick, S. S.; Rice, G. F.

1985-01-01

Apparatus and method for testing TIG (tungsten inert gas) welds of end plugs on a sealed nuclear reactor fuel rod. An X-ray fluorescent spectrograph testing unit detects tungsten inclusion weld defects in the top end plug's seal weld. Separate ultrasonic weld inspection system testing units test the top end plug's seal and girth welds and test the bottom end plug's girth weld for penetration, porosity and wall thinning defects. The nuclear fuel rod is automatically moved into and out from each testing unit and is automatically transported between the testing units by rod handling devices. A controller supervises the operation of the testing units and the rod handling devices

Measurement and modeling of two-phase flow parameters in scaled 8 Multiplication-Sign 8 BWR rod bundle

Energy Technology Data Exchange (ETDEWEB)

Yang, X.; Schlegel, J.P.; Liu, Y.; Paranjape, S.; Hibiki, T. [School of Nuclear Engineering, Purdue University, 400 Central Dr., West Lafayette, IN 47907-2017 (United States); Ishii, M., E-mail: ishii@purdue.edu [School of Nuclear Engineering, Purdue University, 400 Central Dr., West Lafayette, IN 47907-2017 (United States)

2012-04-15

Highlights: Black-Right-Pointing-Pointer Grid spacers have a significant but not well understood effect on flow behavior and development. Black-Right-Pointing-Pointer Two different length scales are present in rod bundles, which must be accounted for in modeling. Black-Right-Pointing-Pointer An easy-to-implement empirical model has been developed for the two-phase friction multiplier. - Abstract: The behavior of reactor systems is predicted using advanced computational codes in order to determine the safety characteristics of the system during various accidents and to determine the performance characteristics of the reactor. These codes generally utilize the two-fluid model for predictions of two-phase flows, as this model is the most accurate and detailed model which is currently practical for predicting large-scale systems. One of the weaknesses of this approach however is the need to develop constitutive models for various quantities. Of specific interest are the models used in the prediction of void fraction and pressure drop across the rod bundle due to their importance in new Natural Circulation Boiling Water Reactor (NCBWR) designs, where these quantities determine the coolant flow rate through the core. To verify the performance of these models and expand the existing experimental database, data has been collected in an 8 Multiplication-Sign 8 rod bundle which is carefully scaled from actual BWR geometry and includes grid spacers to maintain rod spacing. While these spacer grids are 'generic', their inclusion does provide valuable data for analysis of the effect of grid spacers on the flow. In addition to pressure drop measurements the area-averaged void fraction has been measured by impedance void meters and local conductivity probes have been used to measure the local void fraction and interfacial area concentration in the bundle subchannels. Experimental conditions covered a wide range of flow rates and void fractions up to 80%.

Control rod control device

International Nuclear Information System (INIS)

Seiji, Takehiko; Obara, Kohei; Yanagihashi, Kazumi

1998-01-01

The present invention provides a device suitable for switching of electric motors for driving each of control rods in a nuclear reactor. Namely, in a control rod controlling device, a plurality of previously allotted electric motors connected in parallel as groups, and electric motors of any selected group are driven. In this case, a voltage of not driving predetermined selected electric motors is at first applied. In this state an electric current supplied to the circuit of predetermined electric motors is detected. Whether integration or failure of a power source and the circuit of the predetermined electric motors are normal or not is judged by the detected electric current supplied. After they are judged normal, the electric motors are driven by a regular voltage. With such procedures, whether the selected circuit is normal or not can be accurately confirmed previously. Since the electric motors are not driven just at the selected time, the control rods are not operated erroneously. (I.S.)

Correlation of NTD-silicon rod and slice resistivity

International Nuclear Information System (INIS)

Wolverton, W.M.

1984-01-01

Neutron transmutation doped silicon is an electronic material which presents an opportunity to explore a high level of resistivity characterization. This is due to its excellent uniformity of dopant concentration. Appropriate resistivity measurements on the ingot raw material can be used as a predictor of slice resistivity. Correlation of finished NTD rod (i.e. ingot) resistivity to as-cut slice resistivity (after the sawing process) is addressed in the scope of this paper. Empirical data show that the shift of slice-center resistivity compared to rod-end center resistivity is a function of a new kind of rod radial-resistivity gradient. This function has two domains, and most rods are in domain ''A''. Correlating equations show how to significantly improve the prediction of slice resistivity of rods in domain ''A''. The new rod resistivity specifications have resulted in manufacturing economies in the production of NTD silicon slices

Use of poultry protein isolate as a food ingredient: sensory and color characteristics of low-fat Turkey bologna.

Science.gov (United States)

Omana, Dileep A; Pietrasik, Zeb; Betti, Mirko

2012-07-01

The potential of using poultry protein isolate (PPI) as a food ingredient to substitute either soy protein isolate (SPI) or meat protein in turkey bologna was investigated. PPI was prepared from mechanically separated turkey meat using pH-shift technology and the prepared PPI was added to turkey bologna at 2 different concentrations (1.5% and 2% dry weight basis). Product characteristics were compared with those prepared with the addition of 2% SPI, 11% meat protein (control-1), or 13% meat protein (control-2). All the 5 treatments were subjected to sensory analysis to evaluate aroma, appearance, color, flavor, saltiness, juiciness, firmness, and overall acceptability of the turkey bologna samples using 9-point hedonic scales. A turkey bologna control sample with 11% meat protein appeared to be softer compared to other treatments as revealed by texture profile analysis while purge loss during storage in a retail display case was significantly (P Sensory analysis concluded that 1.5% PPI and 2% PPI could be used as substitute of SPI or lean meat and the treatments could be improved by increasing saltiness and decreasing firmness. The study revealed that with slight modifications in saltiness, turkey bologna can be prepared with the addition of poultry protein isolates as an acceptable substitute for soy protein isolate or meat protein. This will help to avoid usage of nonmeat ingredients (as SPI substitute) and to reduce the cost of production (as meat protein substitute) of low-fat turkey bologna. © 2012 Institute of Food Technologists®

Laboratory manual for salt mixing test in rod bundles

International Nuclear Information System (INIS)

Khan, H.U.R.; Chiu, C.; Todreas, N.

1978-10-01

This report is a Laboratory Manual dealing with the procedure employed during Salt Tracer Experiments, which are used for evaluating the hydraulic characteristics of a rod bundle. A description of the standard equipment used is given together with details of manufacture of non-standard items i.e., probes used for detecting the salt-concentration. Details of bundle construction have not been included as they are available in the references cited. An attempt has also been made to point out potential trouble areas and procedures

Lifting device for drilling rods

Energy Technology Data Exchange (ETDEWEB)

Radzivilovich, L L; Laptev, A G; Lipkovich, V A

1982-01-01

A lifter is proposed for drilling rods including a spacer stand with rotating bracket, boom with by-pass rollers, spacing and lifting hydrocylinders with rods and flexible tie mechanism. In order to improve labor productivity by improving maneuverability and to increase the maintenance zone, the lifter is equipped with a hydrocylinder of advance and a cross piece which is installed with the possibility of forward and rotational movement on the stand, and in which by means of the hydrocylinder of advance a boom is attached. Within the indicated boom there is a branch of the flexible tie mechanism with end attached with the possibility of regulation over the length on a rotating bracket, while the rod of the lifting hydrocylinder is connected to the cross piece.

Rodding Surgery

Science.gov (United States)

... Physical activity prior to surgery,  Length of the operation; anesthesia issues,  Reason for the choice of rod,  Time in the hospital,  Length of recovery time at home,  Pain management including control of muscle spasms,  The rehabilitation plan. ...

Mathematical Modeling of the Thermal State of the Spatial Layered Rod Structures

Directory of Open Access Journals (Sweden)

I. V. Stankevich

2016-01-01

Full Text Available The paper considers the features of finite element technology to determine the temperature state of layered rod structures with complex spatial design. The area of research, on the one hand, is defined by the fact that the rod structures (frames are so-called “skeletal framework” of aviation, machinery, shipbuilding products and structures for industrial construction and an issue of implementation of most research and industrial projects, strongly promising from the practical point of view, depends largely on the level of reliability, bearing capacity, and general performance of its “skeletal framework”. On the other hand, the laminates have a wide range and unique combination of valuable properties such as high strength, corrosion resistance, electrical conductivity, thermal conductivity, heat resistance, abrasion resistance and many others. The use of layered metal compositions allows to increase the reliability and durability of a large range of parts and equipment and to reduce significantly the consumption of high-alloyed steels and nonferrous metals. A temperature field is one of the main factors to determine the expected performance of multilayer rod structures, operation conditions of which imply intensive thermal loading.The paper shows how within a single finite element model that approximates the spatial design of steel structures consisting of multilayer curvilinear rods, at the stage of discretization in space to take into account the thermo-physical properties of all materials, forming layer of each timber. Using the technique described in the paper has been created a complex of application programs that allows us to solve a wide class of scientific and applied problems, and explore the impact of various structural, technological and operational factors on the temperature state of multilayer rod structures. The paper presents research results of the multilayer rod design. It shows that the high conductivity layer available

BWR control rod drive scram pilot valve monitoring system

International Nuclear Information System (INIS)

Soden, R.A.; Kelly, V.

1984-01-01

The control rod drive system in a Boiling Water Reactor is the most important safety system in the power plant. All components of the system can be verified except the solenoid operated, scram pilot valves without scramming a rod. The pilot valve mechancial works is the weak link to the control rod drive system. These pilot valves control the hydraulic system which applies pressure to the ''insert'' side of the control rod piston and vents the ''withdraw'' side of the piston causing the rods to insert during a scam. The only verification that the valve is operating properly is to scram the rod. The concern for this portion of the system is demonstrated by the high number of redundant components and complete periodic testing of the electrical circuits. The pilot valve can become hung-up through wear, fracture of internal components, mechanical binding, foreign material or chemicals left in the valve during maintenance, etc. If the valve becomes hung-up the electrical tests performed will not indicate this condition and scramming the rod is in jeopardy. Only an attempt to scram a rod will indicate the hung-up valve. While this condition exists the rod is considered inoperative. This paper describes a system developed at a nuclear power plant that monitors the pilot valves on the control rod drive system. This system utilizes pattern recognition to assure proper internal workings of the scram pilot valves to plant operators. The system is totally automatic such that each time the valve is operated on a ''half scram'', a printout is available to the operator along with light indication that each of the 370 valves (on one unit of a BWR) is operating properly. With this monitoring system installed, all components of the control rod drive system including the solenoid pilot valves can be verified as operational without scramming any rods

BWR control rod drive scram pilot valve monitoring program

International Nuclear Information System (INIS)

Soden, R.A.; Kelly, V.

1986-01-01

The control rod drive system in a Boiling Water Reactor is the most important safety system in the power plant. All components of the system can be verified except the solenoid operated, scram pilot valves without scramming a rod. The pilot valve mechanical works is the weak link to the control rod drive system. These pilot valves control the hydraulic system which applies pressure to the insert side of the control rod piston and vents the withdraw side of the piston causing the rods to insert during a scram. The only verification that the valve is operating properly is to scram the rod. The concern for this portion of the system is demonstrated by the high number of redundant components and complete periodic testing of the electrical circuits. The pilot valve can become hung-up through wear, fracture of internal components, mechanical binding, foreign material or chemicals left in the valve during maintenance, etc. If the valve becomes hung-up the electrical tests performed will not indicate this condition and scramming the rod is in jeopardy. Only an attempt to scram a rod will indicate the hung-up valve. While this condition exists the rod is considered inoperative. This paper describes a system developed at a nuclear power plant that monitors the pilot valves on the control rod drive system. This system utilizes pattern recognition to assure proper internal workings of the scram pilot valves to plant operators. The system is totally automatic such that each time the valve is operated on a half scram, a printout is available to the operator along with light indication that each of the 370 valves (on one unit of a BWR) is operating properly. With this monitoring system installed, all components of the control rod drive system including the solenoid pilot valves can be verified as operational without scramming any rods

Using Facilities And Potential Of Geothermal Resources In The Canakkale Province - NW Turkey

Science.gov (United States)

Deniz, Ozan; Acar Deniz, Zahide

2016-04-01

Turkey, due to its geological location, has a rich potential in point of geothermal resources. Çanakkale province is located northwestern (NW) part of Turkey and it has important geothermal fields in terms of geothermal energy potential. Geothermal resources reach to the surface both effects of past volcanic activity and extensions of fault zones associated with complex tectonic systems in the region. The aim of this study is to summarize hydrogeochemical characteristics, using facilities and potential of hot springs and spas located in the Çanakkale province. There are 13 geothermal fields in the region and the surface temperatures of hot springs are ranging between 28 centigrade degree and 175 centigrade degree. Hydrogeochemical compositions of thermal water display variable chemical compositions. Na, Ca, SO4, HCO3 and Cl are the dominant ions in these waters. Thermal waters of Tuzla and Kestanbol geothermal fields which is located the near coastal area can be noted NaCl type. Because these two geothermal waters have high TDS values, scaling problems are seen around the hot springs and pipelines. Geothermal waters in the province are meteoric origin according to oxygen-18, deuterium and tritium isotopes data. Long underground residence times of these waters and its temperatures have caused both more water - rock interaction and low tritium values. Geothermal energy is utilized in many areas in Turkey today. It is generally used for space heating, balneotherapy and electricity generation. Explorations of geothermal resources and investments in geothermal energy sector have risen rapidly in the recent years particularly in western Turkey. High-temperature geothermal fields are generally located in this region related to the Aegean Graben System and the North Anotalian Fault Zone. All geothermal power plants in Turkey are located in this region. Considering the Çanakkale province, most geothermal fields are suitable for multipurpose usage but many of them have

International symposium on fuel rod simulators: development and application

Energy Technology Data Exchange (ETDEWEB)

McCulloch, R.W. (comp.)

1981-05-01

Separate abstracts are included for each of the papers presented concerning fuel rod simulator operation and performance; simulator design and evaluation; clad heated fuel rod simulators and fuel rod simulators for cladding investigations; fuel rod simulator components and inspection; and simulator analytical modeling. Ten papers have previously been input to the Energy Data Base.

Apparatus for inspecting a irradiated nuclear fuel rod

International Nuclear Information System (INIS)

Saura, Hideaki; Yonemura, Eizo.

1975-01-01

Object: To increase safety and inspection efficiency by operating irradiated fuel rods, which are accommodated in a water-filled pool after being taken out from the reactor. Structure: When making inspection of irradiated fuel rods, particularly the cladding tube thereof, a fuel box which stores irradiated fuel rods in a water pool is secured to a securement mechanism with slime removal apparatus and inspection apparatus on either side capable of being vertically moved, and it is then stopped at a water depth of about 2 meters. When the lid of the box is opened, irradiated fuel rods are taken out with gripping means and then secured together with the gripping means to an operation base provided on the outside of the pool. Thereafter, the box is lowered by operating pedals on the operation base to completely pull out the irradiated fuel rods from the box, and the irradiated fuel rods are then horizontally moved and then held in a suspended state. Next a slime removal apparatus in raised by operating pedals and an inspection element assembly are progressively raised for inspection of the state of the cladding tube of each fuel rod after removal of slime therefrom. (Nakamura, S.)

Wind energy status in renewable electrical energy production in Turkey

International Nuclear Information System (INIS)

Kaygusuz, Kamil

2010-01-01

Main electrical energy sources of Turkey are thermal and hydraulic. Most of the thermal sources are derived from natural gas. Turkey imports natural gas; therefore, decreasing usage of natural gas is very important for both economical and environmental aspects. Because of disadvantages of fossil fuels, renewable energy sources are getting importance for sustainable energy development and environmental protection. Among the renewable sources, Turkey has very high wind energy potential. The estimated wind power capacity of Turkey is about 83,000 MW while only 10,000 MW of it seems to be economically feasible to use. Start 2009, the total installed wind power capacity of Turkey was only 4.3% of its total economical wind power potential (433 MW). However, the strong development of wind energy in Turkey is expected to continue in the coming years. In this study, Turkey's installed electric power capacity, electric energy production is investigated and also Turkey current wind energy status is examined. (author)

Consumer attitudes toward food consumption and purchase in Turkey.

Science.gov (United States)

Uçar, Asli; Ozdoğan, Yahya; Ozçelik, Ayşe Özfer

2012-01-01

This study was conducted in the Ankara Province of Turkey to determine the attitudes of adult consumers toward food consumption and purchasing activities. The data were collected by conducting face-to-face interviews with 700 adults working in ministries (government office) to fill in a questionnaire prepared especially for this purpose. The responses to the questionnaire were evaluated by assigning points for the "food-consumption-and-purchasing attitudes" of each respondent based on their replies. These food-consumption-and-purchasing attitude points have been then analyzed in terms of the gender, age, and educational level of the adults involved. The results showed that women, the 30-39 age group, and university graduates have a higher score of food-consumption-and-purchasing attitude points than do men, the age group comprising respondents < 30 and ≥ 40 years of age, and those with lower education levels, respectively. A statistically significantly relation was observed between food-consumption-and-purchasing attitude points and age.

Slip-spring model of entangled rod-coil block copolymers

Science.gov (United States)

Wang, Muzhou; Likhtman, Alexei E.; Olsen, Bradley D.

2015-03-01

Understanding the dynamics of rod-coil block copolymers is important for optimal design of functional nanostructured materials for organic electronics and biomaterials. Recently, we proposed a reptation theory of entangled rod-coil block copolymers, predicting the relaxation mechanisms of activated reptation and arm retraction that slow rod-coil dynamics relative to coil and rod homopolymers, respectively. In this work, we introduce a coarse-grained slip-spring model of rod-coil block copolymers to further explore these mechanisms. First, parameters of the coarse-grained model are tuned to match previous molecular dynamics simulation results for coils, rods, and block copolymers. For activated reptation, rod-coil copolymers are shown to disfavor configurations where the rod occupies curved portions of the entanglement tube of randomly varying curvature created by the coil ends. The effect of these barriers on diffusion is quantitatively captured by considering one-dimensional motion along an entanglement tube with a rough free energy potential. Finally, we analyze the crossover between the two mechanisms. The resulting dynamics from both mechanisms acting in combination is faster than from each one individually.

Method of driving control rod in reactor

International Nuclear Information System (INIS)

Osa, Hirotaka.

1986-01-01

Purpose: To improve security and safety of the reactor by reducing reactor output automatically and quickly when circulation of cooling water is stopped. Constitution: When the circulating pump is under operation, fluid pressure in the discharge pipe is transferred to the fluid room of fluid pressure cylinder via the control rod drive pipe and lift up the piston, and then the control rod is drawn out of the reactor core. When the circulating pump is lowered in its functions, discharge pipe fluid pressure decreases, fluid pressure in the fluid room decreases, and with less force of piston movement, the control rod gets lowered by its own weight. At this time, the blocked state of the opening by the piston is released, fluid flows into the room. Lowering of pressure and the control rod is promoted by transferring out fluid below the piston in the fluid room to the upper part of the piston via a small gap when the control rod falls by gravity. (Horiuchi, T.)

Hardfacing and welding rods by P/M

International Nuclear Information System (INIS)

Nayar, H.S.

1977-01-01

Certain hardfacing and welding rods are very hard and non-deformable. They are, as it is well known, generally produced by casting processes. Airco has developed a P/M process for producing these rods. The process is already practiced on a semi-production scale. In this process, the powder is poured into suitably designed and prepared molds, vibrated to pack the powder, and sintered at a temperature between the solidus and the liquidus temperatures of the alloy to produce rods with 85% or more of the theoretical density. The P/M process has some distinct advantages over the conventional casting processes. These advantages are highlighted. The process is suitable for producing Fe-, Ni-, Co-, and Cu-base hardfacing and welding rods with and without second phase hard particles such as WC. Microstructures, dimensional and density controls, weld-evaluations and hardness data are included to present evidence that the rods produced by the P/M process are suitable for various welding and hardfacing applications

Assessments of CHF correlations based on full-scale rod bundle experiments

International Nuclear Information System (INIS)

Sardh, K.; Becker, K.M.

1986-02-01

In the present study the Barnett, the Becker, the Biasi, the CISE-4, the XN-1, the EPRI and the Bezrukov burnout correlations have been compared with burnout measurements obtained with full scale 81, 64, 36 and 37-rod bundles. The total power as well as the local power hypothesis was employed for the comparisons. The results clearly indicated that the Biasi and the CISE-4 correlations do not predict the burnout conditions in full-scale rod bundles. Since, these correlations yield non-conservative results their use in computer programs as for instance RELAP, TRAC or NORA should be avoided. Considering that the effects of spacers were not included in the predictions, the Becker and the Bezrukov correlations were in excellent agreement with the experimental data. However, it should be pointed out that the Bezrukov correlation only covered the 70 and 90 bar data, while the Becker correlation agreed with the experimental data in the whole pressure range between 30 and 90 bar. The Barnett, the XN-1 and the EPRI correlations were also in satisfactory agreement with the experiments. We therefore conclude that for predictions of the burnout conditions in full-scale BWR rod bundles the Becker correlation should be employed. (author)

Vernotte-Cattaneo approximation for heat conduction in fuel rod

International Nuclear Information System (INIS)

Espinosa P, G.; Espinosa M, E. G.

2009-10-01

In this paper we explore the applicability of a fuel rod mathematical model based on the Vernotte-Cattaneo transient heat conduction as constitutive law (Non-Fourier approach) for light water reactors transient analysis. In the classical theory of diffusion, the Fourier law of heat conduction is used to describe the relation between the heat conduction is used to describe the relation between the heat flux vector and the temperature gradient assuming that the heat propagation speeds are infinite. The motivation for this research was to eliminate the paradox of an infinite. The motivation for this research was to eliminate the paradox of an infinite thermal wave speed. The time-dependent heat sources were considered in the fuel rod heat transfer model. The close of the main steam isolated valves transient in a boiling water reactor was analyzed for different relaxation times. The results show that for long-times the heat fluxes on the clad surface under Vernotte-Cattaneo approach can be important, while for short-times and from the engineering point of view the changes are very small. (Author)

Control rod driving hydraulic device

International Nuclear Information System (INIS)

Sugano, Hiroshi.

1993-01-01

In a control rod driving hydraulic device for an improved BWR type reactor, a bypass pipeline is disposed being branched from a scram pipeline, and a control orifice and a throttle valve are interposed to the bypass pipeline for restricting pressure. Upon occurrence of scram, about 1/2 of water quantity flowing from an accumulator of a hydraulic control unit to the lower surface of a piston of control rod drives by way of a scram pipeline is controlled by the restricting orifice and the throttle valve, by which the water is discharged to a pump suction pipeline or other pipelines by way of the bypass pipeline. With such procedures, a function capable of simultaneously conducting scram for two control rod drives can be attained by one hydraulic control unit. Further, an excessive peak pressure generated by a water hammer phenomenon in the scram pipeline or the control rod drives upon occurrence of scram can be reduced. Deformation and failure due to the excessive peak pressure can be prevented, as well as vibrations and degradation of performance of relevant portions can be prevented. (N.H.)

Detection of antibodies against Turkey astrovirus in humans.

Science.gov (United States)

Meliopoulos, Victoria A; Kayali, Ghazi; Burnham, Andrew; Oshansky, Christine M; Thomas, Paul G; Gray, Gregory C; Beck, Melinda A; Schultz-Cherry, Stacey

2014-01-01

Astroviruses are a leading cause of gastroenteritis in mammals and birds worldwide. Although historically thought to be species-specific, increasing evidence suggests that astroviruses may cross species barriers. In this report, we used enzyme-linked immunosorbent assays to screen sera from three distinct human cohorts involved in influenza studies in Memphis, TN or Chapel Hill, NC, and Midwestern poultry abattoir workers for antibodies to turkey astrovirus type 2 (TAstV-2). Surprisingly, 26% of one cohort's population was TAstV-2 positive as compared to 0 and 8.9% in the other cohorts. This cohort was composed of people with exposure to turkeys in the Midwestern United States including abattoir workers, turkey growers, and non-occupationally exposed participants. The odds of testing positive for antibodies against turkey astrovirus among abattoir workers were approximately 3 times higher than the other groups. These studies suggest that people with contact to turkeys can develop serological responses to turkey astrovirus. Further work is needed to determine if these exposures result in virus replication and/or clinical disease.

Detection of antibodies against Turkey astrovirus in humans.

Directory of Open Access Journals (Sweden)

Victoria A Meliopoulos

Full Text Available Astroviruses are a leading cause of gastroenteritis in mammals and birds worldwide. Although historically thought to be species-specific, increasing evidence suggests that astroviruses may cross species barriers. In this report, we used enzyme-linked immunosorbent assays to screen sera from three distinct human cohorts involved in influenza studies in Memphis, TN or Chapel Hill, NC, and Midwestern poultry abattoir workers for antibodies to turkey astrovirus type 2 (TAstV-2. Surprisingly, 26% of one cohort's population was TAstV-2 positive as compared to 0 and 8.9% in the other cohorts. This cohort was composed of people with exposure to turkeys in the Midwestern United States including abattoir workers, turkey growers, and non-occupationally exposed participants. The odds of testing positive for antibodies against turkey astrovirus among abattoir workers were approximately 3 times higher than the other groups. These studies suggest that people with contact to turkeys can develop serological responses to turkey astrovirus. Further work is needed to determine if these exposures result in virus replication and/or clinical disease.

Energy policies of IEA countries: Turkey 1997 review

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

This IEA report provides a comprehensive in-depth assessment of the energy policies of Turkey, including recommendations on future policy developments. The report highlights the rapid increase in Turkey`s energy consumption and the large investments needed to meet the demand growth. Turkey has sought to attract private inward investment in the energy sector, in particular in electricity, through build-own-operate and build-operate-transfer schemes and transfers of operating rights. Turkey needs to set up a stable legal framework to continue this policy. It needs to push forward with market reforms, as well as to create a level playing field for competition, with energy prices reflecting the true costs of various fuels. Natural gas consumption is also expected to continue to increase. The new regulatory framework should be designed to encourage more rapid increase in the use of gas and more corresponding investments. Turkey is situated near the Caspian Sea, where natural gas and oil production are expected to increase substantially. The report describes projects for oil and natural gas pipelines. 33 figs., 31 tabs., 4 apps.

Synthesis of homochiral tris-indanyl molecular rods

DEFF Research Database (Denmark)

Kjeldsen, Niels Due; Funder, Erik Daa; Gothelf, Kurt Vesterager

2014-01-01

Homochiral tris-indanyl molecular rods designed for supramolecular surface self-assembly were synthesized. The chiral indanol moiety was constructed via a Ti-mediated alkyne trimerization. Further manipulations resulted in a homochiral indanol monomer. This was employed as the precursor for succe...... for successive Sonogashira and Ohira-Bestman reactions towards the homochiral tris-indanyl molecular rods. The molecular rods will be applied for scanning tunnelling microscopy studies of their surface self-assembly and chirality.......Homochiral tris-indanyl molecular rods designed for supramolecular surface self-assembly were synthesized. The chiral indanol moiety was constructed via a Ti-mediated alkyne trimerization. Further manipulations resulted in a homochiral indanol monomer. This was employed as the precursor...

Analiyzing Main Determinant of Currency, Debt and Banking Crises and Frag ilities in Turkey

Directory of Open Access Journals (Sweden)

Murat Türker

2015-09-01

Full Text Available The basic lessons obtained from financial turbulences all over the wor ld are the need to spot main causes, identify the triggering risk factors and consequently develop resolution plans for the potential financial crises, which include the establishment of a sound and strong financial system with strengthened institutional and structural bodies. Accurately and timely detection of the main causes that trigger financial fragilitiesemerging from currency, debt and banking is supposed to guide regulators to find "to the point" solutions to the fragility problems and to isolate their effects. Since in the Turkey case, financial crises were observed to occur in the form of twin crises or triplet crises, in this paper, we put forward Turkey-specific diagnoses and suggestions. Thus, the main factors that triggered financial turmoils in Turkey's last quarter century are low GDP, inadequate equity capital, insufficient bank returns, poor FX reserve, high inflation, short position-hot money policy, capital outflows, manipulative credit ratings and bank inertia, namely a trade off betweencredit transactions and risk-free investment vehicles

Apparatus for handling control rod drives

International Nuclear Information System (INIS)

Akimoto, A.; Watanabe, M.; Yoshida, T.; Sugaya, Z.; Saito, T.; Ishii, Y.

1979-01-01

An apparatus for handling control rod drives (CRD's) attached by detachable fixing means to housings mounted in a reactor pressure vessel and each coupled to one of control rods inserted in the reactor pressure vessel is described. The apparatus for handling the CRD's comprise cylindrical housing means, uncoupling means mounted in the housing means for uncoupling each of the control rods from the respective CRD, means mounted on the housing means for effecting attaching and detaching of the fixing means, means for supporting the housing means, and means for moving the support means longitudinally of the CRD

Gray rod for a nuclear reactor

International Nuclear Information System (INIS)

Francis, T.A.; Cerni, Samuel.

1986-01-01

The invention relates to an improved gray rod for insertion in a nuclear fuel assembly having an array of fuel rods. The gray rod includes a thin-walled cladding tube a first longitudinal section of which is positioned within, and a second longitudinal section of which is positioned essentially without, the array of fuel rods when the gray rod is inserted in the fuel assembly. The first longitudinal section defines a pellet-receiving space having detained therein a stack of annular pellets with an outer diameter sufficient to lend radial support to the wall of the first longitudinal tube section. The second longitudinal section defines a hollow space devoid of pellets and having means to resist radial collapse under external pressure. This means may be a partially compressed spiral spring which serves the dual purpose of retaining the stack of pellets in the pellet-receiving space and of lending radial support to the wall of the second longitudinal tube section or it may be holes through the wall to allow pressure equalisation. The cladding tube is composed of stainless-steel material having a low neutron-capture cross-section, and the annular pellets preferably being composed of Zircaloy or Zirconia material. (author)

CFD analysis of the dynamic behaviour of a fuel rod subchannel in a supercritical water reactor with point kinetics

International Nuclear Information System (INIS)

Ampomah-Amoako, Emmanuel; Akaho, Edward H.K.; Nyarko, Benjamin J.B.; Ambrosini, Walter

2013-01-01

Highlights: • The analysis of flow stability of nuclear fuel subchannels with supercritical water is presented. • The results obtained by a CFD code are compared with those of a system code. • The model includes also heat conduction in the fuel rod and point neutron kinetics. - Abstract: The paper presents the analysis by a CFD code of coupled neutronic–thermal hydraulic instabilities in a subchannel slice belonging to a square lattice assembly. The work represents a further phase in the assessment of the suitability of CFD codes for studies of flow stability of supercritical fluids; the research started in previous work with the analysis of bare 2D circular pipes and already addressed 3D subchannel slices with no allowance for heat conduction or neutronic effects. In the present phase, a more realistic system is considered, dealing with a slice of a fuel assembly subchannel containing the regions of the pellet, the gap and the cladding and including also the effect of inlet and outlet throttling. The adopted neutronic model is a point kinetics one, including six delayed neutron groups with global Doppler and fluid density feedbacks. The response of the model to perturbations applied starting from a steady-state condition at the rated power is compared with that of a similar model developed for a 1D system code. Upward, horizontal and downward flow orientations are addressed making use of a uniform power profile and changing relevant parameters as the gap equivalent conductance and the density reactivity coefficient. A bottom-peaked power profile is also considered in the case of vertical upward flow. Though the adopted model can still be considered simple in comparison with actual details of fuel assemblies, the obtained results demonstrate the potential of the adopted methodology for more accurate analyses to be made with larger computational resources

Method for verifying the pressure in a nuclear reactor fuel rod

International Nuclear Information System (INIS)

Jones, W.J.

1979-01-01

Disclosed is a method of accurately verifying the pressure contained in a sealed pressurized fuel rod by utilizing a pressure balance measurement technique wherein an end of the fuel rod extends through and is sealed in a wall of a small chamber. The chamber is pressurized to the nominal (desired) fuel rod pressure and the fuel rod is then pierced to interconnect the chamber and fuel rod. The deviation of chamber pressure is noted. The final combined pressure of the fuel rod and drill chamber is substantially equal to the nominal rod pressure; departure of the combined pressure from nominal is in direct proportion to departure of rod pressure from nominal. The maximum error in computing the rod pressure from the deviation of the combined pressure from nominal is estimated at plus or minus 3.0 psig for rod pressures within the specified production limits. If the rod pressure is corrected for rod void volume using a digital printer data record, the accuracy improves to about plus or minus 2.0 psig

Material operating behaviour of ABB BWR control rods

International Nuclear Information System (INIS)

Rebensdorff, B.; Bart, G.

2000-01-01

The BWR control rods made by ABB use boron carbide (B 4 C and hafnium as absorber material within a cladding of stainless steel. The general behaviour under operation has proven to be very good. ABB and many of their control rod customers have performed extensive inspection programs of control rod behaviour. However, due to changes in the material properties under fast and thermal neutron irradiation defects may occur in the control rods at high neutron fluences. Examinations of irradiated control rod materials have been performed in hot cell laboratories. The examinations have revealed the defect mechanism Irradiation Assisted Stress Corrosion Cracking (IASCC) to appear in the stainless steel cladding. For IASCC to occur three factors have to act simultaneously. Stress, material sensitization and an oxidising environment. Stress may be obtained from boron carbide swelling due to irradiation. Stainless steel may be sensitized to intergranular stress corrosion cracking under irradiation. Normally the reactor environment in a BWR is oxidising. The presentation focuses on findings from hot cell laboratory work on irradiated ABB BWR control rods and studies of irradiated control rod materials in the hot cells at PSI. Apart from physical, mechanical and microstructural examinations, isotope analyses were performed to describe the local isotopic burnup of boron. Consequences (such as possible B 4 C washout) of a under operation in a ABB BWR, after the occurrence of a crack is discussed based on neutron radiographic examinations of control rods operated with cracks. (author)

Overview of Turkey's coal necessity, reserves and utilization

Energy Technology Data Exchange (ETDEWEB)

Kilic, Ahmet Mahmut; Kilic, Ozen

2006-10-15

This article deals with overview of Turkey's coal necessity, reserves and utilization. Turkey is rapidly growing in terms of both its economy and its population. In parallel, its demand for energy, particularly for electricity, is increasing. Turkey possesses fossil fuel resources of hard coal (HC) and lignite (LG) have the greatest importance in energy production and for the national economy. The hard coal and lignite reserves of Turkey are 1.126 and 8.375 millions tons(Mt), respectively. Coal, the major fuel source for Turkey utilized mainly for electric power, steel manufacturing and cement production, amounts to 31% of total energy consumption in Turkey. To sum up, providing the total consumption is taken into account in the Middle East, the coal consumption rate of Turkey is approximately 90% of the consumption in this region.

Prototypical Rod Consolidation Demonstration Project

International Nuclear Information System (INIS)

1993-05-01

The objective of Phase III of the Prototypical Rod Consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod Consolidation System as described in the NUS Phase II Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase III effort the system was tested on a component, subsystem, and system level. Volume IV provides the Operating and Maintenance Manual for the Prototypical Rod Consolidation System that was installed at the Cold Test Facility. This document, Book 1 of Volume IV, discusses: Process overview functional descriptions; Control system descriptions; Support system descriptions; Maintenance system descriptions; and Process equipment descriptions

Prototypical Rod Consolidation Demonstration Project

International Nuclear Information System (INIS)

1993-05-01

The objective of Phase III of the Prototypical Rod Consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod Consolidation System as described in the NUS Phase II Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase III effort the system was tested on a component, subsystem, and system level. Volume IV provides the Operating and Maintenance Manual for the Prototypical Rod Consolidation System that was installed at the Cold Test Facility. This document, Book 4 of Volume IV, discusses: Off-normal operating and recovery procedures; Emergency response procedures; Troubleshooting procedures; and Preventive maintenance procedures

Femicide in Turkey between 2000 and 2010

Science.gov (United States)

Toprak, Sadik; Ersoy, Gokhan

2017-01-01

Although intimate partner violence (IPV) is an important problem that threatens women’s health, very few studies focus on the victim—perpetrator relationship or examine this relationship across Turkey. The aim of this study is to contribute to a better understanding of femicide cases in Turkey and to describe the socio-demographic, clinical, forensic, and criminological characteristics of femicide victims and offenders. This study analysed 162 femicide cases that occurred in 12 cities in Turkey from 1 January 2000 to 31 December 2010. Eighty women were killed by their partners (classified as intimate partner femicide, IPF), and 81 women were killed by one of their relatives, friends, or strangers (classified as non-intimate partner femicide, non-IPF). According to our results, the typical IPF victim is of child-bearing age, does not have a paid job, is married or divorced, is killed in a domestic setting due to injuries to the thorax or abdomen produced by an edged/pointed weapon or firearm, and is possibly a victim of overkill. The typical IPF perpetrator is close to his victim’s age, has a paid job, has no mental disability, owns a gun, and has threatened his partner or ex-partner previously because of jealousy/infidelity/honour or separation. The typical non-IPF victim is very similar to the IPF victim; however, her marital status can be single, married or divorced, and she is commonly killed by a relative. The surveillance and screening of femicide and IPV is an important step when analysing and attempting to prevent femicide. Second, the training and sensitization of health professionals are important. Moreover, health staff should be encouraged to participate in advocacy interventions. Third, gun ownership must be brought under control. PMID:28832596

An evaluation of inflation expectations in Turkey

Directory of Open Access Journals (Sweden)

Barış Soybilgen

2017-03-01

Full Text Available Expectations of inflation play a critical role in the process of price setting in the market. Central banks closely follow developments in inflation expectations to implement a successful monetary policy. The Central Bank of the Republic of Turkey (CBRT conducts a survey of experts and decision makers in the financial and real sectors to reveal market expectations and predictions of current and future inflation. The survey is conducted every month. This paper examines the accuracy of these survey predictions using forecast evaluation techniques. We focus on both point and sign accuracy of the predictions. Although point predictions from CBRT surveys are compared with those of autoregressive models, sign predictions are evaluated on their value to a user. We also test the predictions for bias. Unlike the empirical evidence from other economies, our results show that autoregressive models outperform most of inflation expectations in forecasting inflation. This indicates that inflation expectations have poor point forecast accuracies. However, we show that sign predictions for all inflation expectations have value to a user.

Fuel rod failure due to marked diametral expansion and fuel rod collapse occurred in the HBWR power ramp experiment

International Nuclear Information System (INIS)

Yanagisawa, Kazuaki

1985-12-01

In the power ramp experiment with the BWR type light water loop at the HBWR, the two pre-irradiated fuel rods caused an unexpected pellet-cladding interaction (PCI). One occurred in the fuel rod with small gap of 0.10 mm, which was pre-irradiated up to the burn-up of 14 MWd/kgU. At high power, the diameter of the rod was increased markedly without accompanying significant axial elongation. The other occurred in the rod with a large gap of 0.23 mm, which was pre-irradiated up to the burn-up of 8 MWd/kgU. The diameter of the rod collapsed during a diameter measurement at the maximum power level. The causes of those were investigated in the present study by evaluating in-core data obtained from equipped instruments in the experiment. It was revealed from the investigation that these behaviours were attributed to the local reduction of the coolant flow occurred in the region of a transformer in the ramp rig. The fuel cladding material is seemed to become softened due to temperature increase caused by the local reduction of the coolant flow, and collapsed by the coolant pressure, either locally or wholly depending on the rod diametral gap existed. (author)

Oil and gas market developments in Turkey

International Nuclear Information System (INIS)

Kaygusuz, K.

2003-01-01

Turkey's strategic location makes it a natural 'energy bridge' between major oil and gas producing areas in the Middle East and Caspian Sea regions on one hand and consumer markets in Europe on the other. Oil consumption has increased in recent years in Turkey, and this trend is expected to continue, with growth of 2-3% annually in coming years. The annual oil consumption of the country is around 31.3 million tons, while 83% of total consumption is supplied from imports and only 17% is supplied from indigenous production. Oil provides around 43% of Turkey's total energy requirements, but its share is declining (as the share of natural gas rises). On the other hand, due to diversification efforts of energy sources, use of natural gas was newly introduced into the Turkish economy in 1987 and has been growing rapidly. Turkey's natural gas reserves seem limited and current gas production in the country meets 2.8% of domestic consumption requirements. The annual natural gas consumption of Turkey is around 14.7 billion m 3 and is assumed to increase by 12% per annum. Turkish natural gas use is projected to increase dramatically in coming years, with the prime consumers expected to be industry and power plants. Turkey has chosen natural gas as the preferred fuel for the massive amount of new power plant capacity to be added in coming years. (Author)

Experimental studies of the effect of rod spacing on burnout in a simulated rod bundle

International Nuclear Information System (INIS)

Lee, D.H.; Little, R.B.

1962-08-01

Tests on a dumb-bell shaped flow passage simulating the gap between rods in a fuel element indicated that burnout was not significantly affected by inter-rod gap in the range 0.032'' to 0.22''. Test conditions were: 960 p.s.i.a., 2 x 10 6 1b/ft 2 hr mass velocity, and 10% mean exit quality with vertical upflow of water. (author)

A snapshot of geothermal energy potential and utilization in Turkey

International Nuclear Information System (INIS)

Erdogdu, Erkan

2009-01-01

Turkey is one of the countries with significant potential in geothermal energy. It is estimated that if Turkey utilizes all of her geothermal potential, she can meet 14% of her total energy need (heat and electricity) from geothermal sources. Therefore, today geothermal energy is an attractive option in Turkey to replace fossil fuels. Besides, increase in negative effects of fossil fuels on the environment has forced many countries, including Turkey, to use renewable energy sources. Also, Turkey is an energy importing country; more than two-thirds of her energy requirement is supplied by imports. In this context, geothermal energy appears to be one of the most efficient and effective solutions for sustainable energy development and environmental pollution prevention in Turkey. Since geothermal energy will be used more and more in the future, its current potential, usage, and assessment in Turkey is the focus of the present study. The paper not only presents a review of the potential and utilization of the geothermal energy in Turkey but also provides some guidelines for policy makers. (author)

Synthesis, strong room-temperature PL and photocatalytic activity of ZnO/ZnWO{sub 4} rod-like nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Validzic, Ivana Lj., E-mail: validzic@vinca.rs [Vinca Institute of Nuclear Sciences, University of Belgrade, P.O. Box 522, 11001 Belgrade (Serbia); Savic, Tatjana D.; Krsmanovic, Radenka M.; Jovanovic, Dragana J.; Novakovic, Mirjana M.; Popovic, Maja C.; Comor, Mirjana I. [Vinca Institute of Nuclear Sciences, University of Belgrade, P.O. Box 522, 11001 Belgrade (Serbia)

2012-05-25

Highlights: Black-Right-Pointing-Pointer Novel low temperature method for the synthesis of ZnO/ZnWO{sub 4} rod-like nanoparticles. Black-Right-Pointing-Pointer PL showed strong UV band peaked at 3.30 eV and a visible band at 2.71 and 2.53 eV. Black-Right-Pointing-Pointer Variations of the two PL bands were observed for different excitation wavelengths. Black-Right-Pointing-Pointer Band-gap energies of ZnO/ZnWO{sub 4} nanoparticles were found to be 3.62 and 3.21 eV. Black-Right-Pointing-Pointer Photocatalytic behaviour of ZnO is dependent on the formation of ZnWO{sub 4} phase. - Abstract: Zinc oxide (ZnO)/zinc tungstate (ZnWO{sub 4}) rod-like nanoparticles with diameters in the range of 6-11 nm and length of about 30 nm were synthesized by a low temperature soft solution method at 95 Degree-Sign C in the presence of non-ionic copolymer surfactant. It was found that their crystallinity was enhanced with the increase of heating time from 1 h up to 120 h. The photoluminescence (PL) measurements showed very strong, narrow UV band peaked at 3.30 eV and a broad visible band peaking at 2.71 eV with a shoulder at about 2.53 eV, for {lambda}{sub exc} < 300 nm. Quite large variations in the intensities of the two PL bands were observed for different excitation wavelengths. The intensity of the main visible band decreases with decreasing excitation energy and disappears when samples are excited {lambda} = 320 nm (E{sub exc} = 3.875 eV). We found that observed optical properties originate from ZnO phase. UV band gap PL had high intensity for all applied excitations, probably induced by ZnWO{sub 4} phase presence on the surface. In addition, two values were found for direct band-gap energy of ZnO/ZnWO{sub 4} rod-like nanoparticles 3.62 and 3.21 eV, determined from reflectance spectrum. The photocatalytic behaviour of ZnO is strongly dependent on the formation of ZnWO{sub 4} phase, of the obtained rod-like nanoparticles.

Influence on rewetting temperature and wetting delay during rewetting rod bundle by various radial jet models

Energy Technology Data Exchange (ETDEWEB)

Debbarma, Ajoy; Pandey, Krishna Murari [National Institute of Technology, Assam (India). Dept. of Mechanical Engineering

2016-03-15

Numerical investigation of the rewetting of single sector fuel assembly of Advanced Heavy Water Reactor (AHWR) has been carried out to exhibit the effect of coolant jet diameters (2, 3 and 4 mm) and jet directions (Model: M, X and X2). The rewetting phenomena with various jet models are compared on the basis of rewetting temperature and wetting delay. Temperature-time curve have been evaluated from rods surfaces at different circumference, radial and axial locations of rod bundle. The cooling curve indicated the presence of vapor in respected location, where it prevents the contact between the firm and fluid phases. The peak wall temperature represents as rewetting temperature. The time period observed between initial to rewetting temperature point is wetting delay. It was noted that as improved in various jet models, rewetting temperature and wetting delay reduced, which referred the coolant stipulation in the rod bundle dominant vapor formation.

Influence on rewetting temperature and wetting delay during rewetting rod bundle by various radial jet models

International Nuclear Information System (INIS)

Debbarma, Ajoy; Pandey, Krishna Murari

2016-01-01

Numerical investigation of the rewetting of single sector fuel assembly of Advanced Heavy Water Reactor (AHWR) has been carried out to exhibit the effect of coolant jet diameters (2, 3 and 4 mm) and jet directions (Model: M, X and X2). The rewetting phenomena with various jet models are compared on the basis of rewetting temperature and wetting delay. Temperature-time curve have been evaluated from rods surfaces at different circumference, radial and axial locations of rod bundle. The cooling curve indicated the presence of vapor in respected location, where it prevents the contact between the firm and fluid phases. The peak wall temperature represents as rewetting temperature. The time period observed between initial to rewetting temperature point is wetting delay. It was noted that as improved in various jet models, rewetting temperature and wetting delay reduced, which referred the coolant stipulation in the rod bundle dominant vapor formation.

Rebirth of a control rod at the Phenix power plant

International Nuclear Information System (INIS)

De Carvalho, Corinne; Vignau, Bernard; Masson, Marc

2007-01-01

This paper outlines the operations involved in cleaning the control rod for the complementary shutdown system in the Phenix Power Plant, the French sodium-cooled fast reactor. The Phenix reactor is controlled by six control rods and a complementary shutdown system. The latter comprises a control rod and a mechanism maintaining the rod in position by means of an electromagnet. The electromagnet is continuously supplied with power and holds the rod control assembly in position by magnetisation on a plane circular surface made from pure iron. The bearing capacity of the mechanism on the rod was initially 80 daN with a rod weight of 26.3 daN. This deteriorated progressively over time. The bearing surface of the rod and the electromagnet became contaminated with a deposit of sodium oxides and metallic particles, thus creating an air gap. This reached a figure of 36 daN in 2005 and was deemed not to be sufficient to prevent the rod from dropping at the wrong time during reactor operation. The Power Plant thus decided to replace the rod mechanism in the reactor in an initial phase, followed by the control rod itself. As the Phenix Power Plant had no spare control rods left, they initiated a 'salvage' plan, over two stages, for the rod removed from the reactor and placed in the fuel storage drum: - Inspection of the bearing surface of the rod by means of a borescope to check whether the rod could be salvaged, - A cleaning operation on the bearing face and checks on the bearing capacity of the rod. The operation is subject to very stringent requirements: the rod must not be taken out of the sodium to ensure that it can be reused in the reactor. The operation must thus take place in the fuel storage drum where there are no facilities for such an operation and where operating conditions are very hostile: high temperatures (the sodium in the fuel storage drum is at a temperature of 150 deg. C, high dose rate (3 mGy/h on the bearing surface) and the bearing surface is submerged

Means for driving control rod

International Nuclear Information System (INIS)

Sato, Haruo; Sasaki, Masayoshi.

1974-01-01

Object: To enable wire rope to be readily removed from guide pulleys for the inspection or replacement of control rods. Structure: A pair of guide pulleys disposed to oppose each other are provided on their periphery with respective notches which are arranged in a staggered fashion. In this way, the rope is made to be removed from the notches for inspection of the control rod or for other purposes. (Kamimura, M.)

Self-contact for rods on cylinders

NARCIS (Netherlands)

G.H.M. van der Heijden; M.A. Peletier (Mark); R. Planqué (Robert)

2004-01-01

textabstractWe study self-contact phenomena in elastic rods that are constrained to lie on a cylinder. By choosing a particular set of variables to describe the rod centerline the variational setting is made particularly simple: the strain energy is a second-order functional of a single scalar

Spider and burnable poison rod combinations

International Nuclear Information System (INIS)

Walton, L.A.

1980-01-01

A description is given of an improved design of burnable poison rods and their associated spiders used in the fuel assemblies of pressurized water power reactor cores which allows the rods to be installed and removed more quickly, simply and gently than in previously described systems. (U.K.)

Control rod homogenization in heterogeneous sodium-cooled fast reactors

International Nuclear Information System (INIS)

Andersson, Mikael

2016-01-01

The sodium-cooled fast reactor is one of the candidates for a sustainable nuclear reactor system. In particular, the French ASTRID project employs an axially heterogeneous design, proposed in the so-called CFV (low sodium effect) core, to enhance the inherent safety features of the reactor. This thesis focuses on the accurate modeling of the control rods, through the homogenization method. The control rods in a sodium-cooled fast reactor are used for reactivity compensation during the cycle, power shaping, and to shutdown the reactor. In previous control rod homogenization procedures, only a radial description of the geometry was implemented, hence the axially heterogeneous features of the CFV core could not be taken into account. This thesis investigates the different axial variations the control rod experiences in a CFV core, to determine the impact that these axial environments have on the control rod modeling. The methodology used in this work is based on previous homogenization procedures, the so-called equivalence procedure. The procedure was newly implemented in the PARIS code system in order to be able to use 3D geometries, and thereby be take axial effects into account. The thesis is divided into three parts. The first part investigates the impact of different neutron spectra on the homogeneous control-rod cross sections. The second part investigates the cases where the traditional radial control-rod homogenization procedure is no longer applicable in the CFV core, which was found to be 5-10 cm away from any material interface. In the third part, based on the results from the second part, a 3D model of the control rod is used to calculate homogenized control-rod cross sections. In a full core model, a study is made to investigate the impact these axial effects have on control rod-related core parameters, such as the control rod worth, the capture rates in the control rod, and the power in the adjacent fuel assemblies. All results were compared to a Monte

Control-rod scram device

International Nuclear Information System (INIS)

Matsui, Yoshiro; Saito, Koji.

1986-01-01

Purpose: To eliminate the requirement for the nitrogen gas system in a scram device and enable safety and reliable shutdown of a water-cooled reactor power plant. Constitution: A piston and a spring are contained within a hydraulic vessel, and the piston is driven by the energy stored in the spring so as to supply hydraulic water to control mechanisms. During usual reactor operation, a scram valve is closed and a high water pressure of about 130 kg/cm 2 is applied to the water filled in the vessel through a check valve. Upon occurrence of abnormal conditions and generation of scram signals, the scram valve is opened to supply the water filled in the vessel through the scram valve to the control rod drive mechanisms. When the water pressure in the vessel is decreased, since the piston is urged upwardly by the energy stored in the spring, the water filled in the vessel is intermitently supplied to the control rod drive mechanisms. Thus, control rods can be inserted into the nuclear reactor to shutdown the same. (Horiuchi, T.)

Study on Sumbawa gold ore liberation using rod mill: effect of rod-number and rotational speed on particle size distribution

Science.gov (United States)

Prasetya, A.; Mawadati, A.; Putri, A. M. R.; Petrus, H. T. B. M.

2018-01-01

Comminution is one of crucial steps in gold ore processing used to liberate the valuable minerals from gaunge mineral. This research is done to find the particle size distribution of gold ore after it has been treated through the comminution process in a rod mill with various number of rod and rotational speed that will results in one optimum milling condition. For the initial step, Sumbawa gold ore was crushed and then sieved to pass the 2.5 mesh and retained on the 5 mesh (this condition was taken to mimic real application in artisanal gold mining). Inserting the prepared sample into the rod mill, the observation on effect of rod-number and rotational speed was then conducted by variating the rod number of 7 and 10 while the rotational speed was varied from 60, 85, and 110 rpm. In order to be able to provide estimation on particle distribution of every condition, the comminution kinetic was applied by taking sample at 15, 30, 60, and 120 minutes for size distribution analysis. The change of particle distribution of top and bottom product as time series was then treated using Rosin-Rammler distribution equation. The result shows that the homogenity of particle size and particle size distribution is affected by rod-number and rotational speed. The particle size distribution is more homogeneous by increasing of milling time, regardless of rod-number and rotational speed. Mean size of particles do not change significantly after 60 minutes milling time. Experimental results showed that the optimum condition was achieved at rotational speed of 85 rpm, using rod-number of 7.

Mycoplasma gallopavonis in eastern wild turkeys.

Science.gov (United States)

Luttrell, M P; Eleazer, T H; Kleven, S H

1992-04-01

Serum samples and tracheal cultures were collected from eastern wild turkeys (Meleagris gallopavo sylvestris) trapped for relocation in South Carolina (USA) during 1985 to 1990. Sera were tested for Mycoplasma gallisepticum and M. synoviae by the rapid plate agglutination and hemagglutination inhibition tests and were found to be negative. Tracheal cultures were negative for all pathogenic Mycoplasma spp., including M. gallisepticum, M. synoviae, M. meleagridis, and M. iowae. However, M. gallopavonis was isolated from every group of wild turkeys tested in 1986 to 1990. These data suggest that M. gallopavonis, which is generally considered nonpathogenic, may be a common microorganism in eastern wild turkeys.

Control rod drives for FBR type reactor

International Nuclear Information System (INIS)

Ikakura, Hiroaki.

1990-01-01

The control rod drives for an FBR type reactor of the present invention eliminate obstacles deposited on attracting surfaces between an electromagnet and an armature which connect control rods to recover their retaining power. That is, a sealed chamber capable of controlling its inner pressure by an operation from the outside of a reactor is disposed in an extension pipe, and a nozzle connected to the sealed chamber and facing at the lower end thereof to the attracting surface is disposed. Liquid sodium sucked by evacuating the sealed chamber is jetted out from the nozzle by pressurizing the chamber to simultaneously eliminate obstacles deposited to the attracting surfaces of the electromagnet and the control rod. Alternatively, a nozzle protruding from and retracting to the lower surface of the electromagnet is disposed opposing to each of the attracting surfaces of the electromagnet and the control rod. Similar effect can also be obtained if gases are jetted out in this state. As a result, control rod drives of high reliability for a FBR type reactor can be obtained. (I.S.)

Overview of Japanese control rods development program

International Nuclear Information System (INIS)

Koyama, M.

1984-01-01

The Japanese control rods development program was established based on the fast breeder reactor program. Therefore, PNC's efforts have been made mainly for the development of analysis, design and fabrication technologies for ''JOYO'' and ''MONJU'' control rods. Laboratory studies were performed to obtain the information for absorber materials. The design and fabrication of the sealed and vented type control rod pins were completed, and water loop tests and in-sodium tests were carried out. Irradiation behavior of enriched B 4 C pellets with low and high density in DFR was examined. Japan's experimental fast reactor, JOYO, has been operated at the rated power of 50MWt and 75MWt since April 1977 when the MK-I core (breeder core) attained initial criticality. Post irradiation examinations on control rod, removed from the reactor, were carried out and their performance behavior were evaluated. In the MK-II core, a control rods monitoring program has been in investigation. Absorber Materials Irradiation Rigs (AMIR) are scheduled to be loaded and irradiated in the JOYO MK-II core from 1984. (author)

Protective guide structure for reactor control rod

International Nuclear Information System (INIS)

Ban, Minoru; Umeda, Kenji; Kubo, Noboru; Ito, Tomohiro.

1996-01-01

The present invention provides an improved protective guide structure for control rods, which does not cause swirling of coolants and resonance even though a slit is formed on a protective tube which surrounds a control rod element in a PWR type reactor. Namely, a reactor control rod is constituted with elongated control elements collectively bundled in the form of a cluster. The protective guide structure protectively guides the collected constituent at the upper portion of a reactor container. The protective structure comprises a plurality of protective tubes each having a C-shaped cross section disposed in parallel for receiving control rod elements individually in which the corners of the opening of the cross section of the protective tube are chamfered to an appropriate configuration. With such a constitution, even if coolant flows in a circumferential direction along the protective tubes surrounding the control rod elements, no shearing stream is caused to the coolants flow since the corners of the cross sectional opening (slit) of the tube are chamfered. Accordingly, occurrence of swirlings can be suppressed. (I.S.)

The “Soft Power” policy of Turkey towards Georgia

Directory of Open Access Journals (Sweden)

Larisa Mgerovna Aleksanyan

2016-01-01

Full Text Available South Caucasus throughout history was at the epicenter of clashes of different religions, civilizations, nations and states. At present moment the interests of both regional (Turkey, Iran and global actors (the United States, NATO, the EU, Russia and others. intersect in the region. Global transformations, changing power relations in international relations have their direct influence on the political processes taking place in the region. These processes are also linked with the activities of Turkey, which aspire to regional leadership. It is Georgia, which serves as a corridor between Turkey and states of Central Asia and the South Caucasus. Turkey spreads its influence in Georgia in almost all areas using economic, military and political tools, as well as the Russian-Georgian deteriorated relations. To achieve its goals, Turkey is actively pursuing a strategy of "soft power", which further strengthens its influence in the country. Public diplomacy is a part of soft power, which also ensures the formation of a positive and attractive image of Turkey in Georgia. This article investigates the contemporary policy of "soft power" of Turkey towards Georgia. It analyses the basic tools, institutions and the direction of this policy, actively implemented by the Republic of Turkey. Particular attention is paid to the activities of the Gulen Movement in Georgia. The author makes general conclusions regarding the effectiveness of this policy.

Installing and detaching apparatus for a control rod drive mechanism

International Nuclear Information System (INIS)

Akimoto, Seiichi; Watanabe, Mitsuhiro; Yoshida, Tomiharu; Sugaya, Jun-ichi; Saito, Takashi.

1976-01-01

Object: To facilitate maintenance and repair of a control rod drive mechanism. Structure: The apparatus comprises a means moving in a moving direction of a control rod within a reactor vessel, said moving means having a housing mounted thereon, a means mounted on the reactor vessel to release a connection between a control rod drive mechanism connected to the control rod and the control rod, and a means for mounting and removing a fixing means which connects the reactor vessel to the control rod drive means. With this arrangement, cooling water of high radioactivity level may not be leaked outside to thereby notably reduce dangerousness of exposure and materially cut time required for mounting and removing the control rod drive mechanism. (Ohara, T.)

Self-contact for rods on cylinders

NARCIS (Netherlands)

Heijden, van der G.H.M.; Peletier, M.A.; Planqué, R.

2006-01-01

We study self-contact phenomena in elastic rods that are constrained to lie on a cylinder. By choosing a particular set of variables to describe the rod centerline the variational setting is made particularly simple: the strain energy is a second-order functional of a single scalar variable, and the

Self-contact for rods on cylinders

NARCIS (Netherlands)

Heijden, van der G.H.M.; Peletier, M.A.; Planqué, R.

2004-01-01

We study self-contact phenomena in elastic rods that are constrained to lie on a cylinder. By choosing a particular set of variables to describe the rod centerline the variational setting is made particularly simple: the strain energy is a second-order functional of a single scalar variable, and the

LGBT in Turkey: Policies and Experiences

Directory of Open Access Journals (Sweden)

Ceylan Engin

2015-09-01

Full Text Available While LGBT studies have been problematizing normative categories of sexuality primarily in Western cultures, the status of lesbian, gay, bisexual, and transgender (LGBT individuals in non-Western societies remains understudied. This study examines the political attitudes toward LGBT individuals in Turkish society and explores the experiences of transgender individuals. While Turkey holds a strong economic position among Western countries, the situation of sexual minorities lags behind international standards. This study explores two research questions. First, what is the Turkish government’s outlook for the LGBT community? Secondly, what kind of problems and challenges do trans-individuals experience in Turkey? This study first introduces a macro-level analysis of the politics of gender identity in Turkey by analyzing the debates of four deputies in the Turkish Parliament, each representing their parties’ disparate viewpoints. Secondly, a micro-level analysis of previously collected interviews with twenty-five trans-individuals are also examined that shed light on the difficulties of being a trans-individual in Turkey. The content analysis shows that trans-individuals experience physical, sexual, and emotional violence, in addition to experiencing discrimination in employment, housing, and healthcare. The findings of this micro-level analysis elucidate the continuous discrimination, inequality, and violence that these individuals experience, while the macro-level analysis portrays the state’s discriminatory policies toward LGBT individuals in Turkey.

Effects of different rod spacers (helical types) on coolant crossmixing

International Nuclear Information System (INIS)

Zhukov, A.V.; Sviridenko, E.Ya.; Matyukhin, N.M.; Rymkevich, K.S.; Ushakov, P.A.

1981-11-01

The results of investigations (electromagnetic measuring method) on coolant cross mixing in rod clusters with spiral wire spacers with different winding directions, with alternating unfinned and finned rods (case 'fin to rod'), as well as in rod clusters with much space between the rods, (case 'fin to fin') are reported. The local fluid dynamics parameters (distribution of the transversal and longitudinal velocity component) that define the physical processes of the coolant exchange in the rod clusters with helical spacers are explained. The investigation results for different helical spacer types are compared with each other. (orig.) [de

Ultrasonics aids the identification of failed fuel rods

International Nuclear Information System (INIS)

Anon.

1985-01-01

Over a number of years Brown Boveri Reaktor of West Germany has developed and commercialized an ultrasonic failed fuel rod detection system. Sipping has up to now been the standard technique for failed fuel detection, but sipping can only indicate whether or not an assembly contains defective rods; the BBR system can tell which rod is defective. (author)

Acoustic sensor for in-pile fuel rod fission gas release measurement

International Nuclear Information System (INIS)

Fourmentel, D.; Villard, J. F.; Ferrandis, J. Y.; Augereau, F.; Rosenkrantz, E.; Dierckx, M.

2009-01-01

We have developed a specific acoustic sensor to improve the knowledge of fission gas release in Pressurized Water Reactor (PWR) fuel rods when irradiated in materials testing reactors. In order to perform experimental programs related to the study of the fission gas release kinetics, the CEA (French Nuclear Energy Commission) acquired the ability to equip a pre-irradiated PWR fuel rod with three sensors, allowing the simultaneous on-line measurements of the following parameters: - fuel temperature with a centre-line thermocouple type C, - internal pressure with a specific counter-pressure sensor, - fraction of fission gas released in the fuel rod with an innovative acoustic sensor. The third detector is the subject of this paper. This original acoustic sensor has been designed to measure the molar mass and pressure of the gas contained in the fuel rod plenum. For in-pile instrumentation, the fraction of fission gas, such as Krypton and Xenon, in Helium, can be deduced online from this measurement. The principle of this acoustical sensor is the following: a piezoelectric transducer generates acoustic waves in a cavity connected to the fuel rod plenum. The acoustic waves are propagated and reflected in this cavity and then detected by the transducer. The data processing of the signal gives the velocity of the acoustic waves and their amplitude, which can be related respectively to the molar mass and to the pressure of the gas. The piezoelectric material of this sensor has been qualified in nuclear conditions (gamma and neutron radiations). The complete sensor has also been specifically designed to be implemented in materials testing reactors conditions. For this purpose some technical points have been studied in details: - fixing of the piezoelectric sample in a reliable way with a suitable signal transmission, - size of the gas cavity to avoid any perturbation of the acoustic waves, - miniaturization of the sensor because of narrow in-pile experimental devices

Rights of the Child in Turkey.

Science.gov (United States)

Naqvi, Yasmin

This report to the United Nations Convention on the Rights of the Child contains observations of the World Organisation Against Torture (OMCT) concerning the application of the Convention by Turkey and observations regarding violence against girls in Turkey. The report is presented in three major parts. Part 1 asserts that despite the considerable…

Method for installing a control rod driving device in a reactor

International Nuclear Information System (INIS)

Sato, Haruo; Watanabe, Masatoshi.

1975-01-01

Object: To install a device using a wire rope, including individually moving up and down a control rod and a control rod driving device thereby enabling to install them within a low house and to reduce time required for installing operation. Structure: The control rod is temporarily attached to a support structure for the control rod driving device, the control rod driving device is suspended on a crane positioned upwardly of the support structure, a rope connected to the control rod driving device is connected to the control rod, a sagged portion of the rope is then wound about a rotary cylinder, the control rod is disconnected from its temporary attachment, and the wound rope is wound back while the rotary cylinder is rotated to move down the control rod. After the rope has been released from the rotary cylinder, the control rod driving device is moved down by the crane. (Kamimura, M.)

Influence of implant rod curvature on sagittal correction of scoliosis deformity.

Science.gov (United States)

Salmingo, Remel Alingalan; Tadano, Shigeru; Abe, Yuichiro; Ito, Manabu

2014-08-01

Deformation of in vivo-implanted rods could alter the scoliosis sagittal correction. To our knowledge, no previous authors have investigated the influence of implanted-rod deformation on the sagittal deformity correction during scoliosis surgery. To analyze the changes of the implant rod's angle of curvature during surgery and establish its influence on sagittal correction of scoliosis deformity. A retrospective analysis of the preoperative and postoperative implant rod geometry and angle of curvature was conducted. Twenty adolescent idiopathic scoliosis patients underwent surgery. Average age at the time of operation was 14 years. The preoperative and postoperative implant rod angle of curvature expressed in degrees was obtained for each patient. Two implant rods were attached to the concave and convex side of the spinal deformity. The preoperative implant rod geometry was measured before surgical implantation. The postoperative implant rod geometry after surgery was measured by computed tomography. The implant rod angle of curvature at the sagittal plane was obtained from the implant rod geometry. The angle of curvature between the implant rod extreme ends was measured before implantation and after surgery. The sagittal curvature between the corresponding spinal levels of healthy adolescents obtained by previous studies was compared with the implant rod angle of curvature to evaluate the sagittal curve correction. The difference between the postoperative implant rod angle of curvature and normal spine sagittal curvature of the corresponding instrumented level was used to evaluate over or under correction of the sagittal deformity. The implant rods at the concave side of deformity of all patients were significantly deformed after surgery. The average degree of rod deformation Δθ at the concave and convex sides was 15.8° and 1.6°, respectively. The average preoperative and postoperative implant rod angle of curvature at the concave side was 33.6° and 17.8�

Flow in rod bundles

International Nuclear Information System (INIS)

Hazi, G.; Mayer, G.

2005-01-01

For power upgrading VVER-440 reactors we need to know exactly how the temperature measured by the thermocouples is related to the average outlet temperature of the fuel assemblies. Accordingly, detailed knowledge on mixing process in the rod bundles and in the fuel assembly head have great importance. Here we study the hydrodynamics of rod bundles based on the results of direct numerical and large eddy simulation of flows in subchannels. It is shown that secondary flow and flow pulsation phenomena can be observed using both methodologies. Some consequences of these observations are briefly discussed. (author)

Impact loading of a BWR control rod during braking

International Nuclear Information System (INIS)

Heeschen, U.

1977-01-01

In an emergency case the control rods of a boiling water reactor are shot into the RPV from below against the weight of the rods with drive motors. According to the position of the control rods between the fuel elements the rods can reach in that case velocities up to 4 m/s. The moved masses of the control rods and of the pistons (both of them are connected by a coupling) are braked through a cup spring which transfers its forces to the RPV-bottom sphere. The spring has to be designed that in this case tthe complete kinetic energy of he control rods of about 1000Nm can be taken up. The spring power and the inertia of the moved masses cause extremely high loadings during and shortly after the impact onto the spring. The shock-like loading propagates along the whole rod at the speed of sound, and this is also the reason why the weaker cross-sections have to endure considerable short-term stress peaks. (Auth.)

Rapid and accurate control rod calibration measurement and analysis

International Nuclear Information System (INIS)

Nelson, George W.; Doane, Harry J.

1990-01-01

In order to reduce the time needed to perform control rod calibrations and improve the accuracy of the results, a technique for a measurement, analysis, and tabulation of integral rod worths has been developed. A single series of critical rod positions are determined at constant low power to reduce the waiting time between positive period measurements and still assure true stable reactor period data. Reactivity values from positive period measurements and control rod drop measurements are used as input data for a non-linear fit to the expected control rod integral worth shape. With this method, two control rods can be calibrated in about two hours, and integral and differential calibration tables for operator use are printed almost immediately. Listings of the BASIC computer programs for the non-linear fitting and calibration table preparation are provided. (author)

Drilling Experiments of Dummy Fuel Rods Using a Mock-up Drilling Device and Detail Design of Device for Drilling of Irradiated Nuclear Fuel Rods

Energy Technology Data Exchange (ETDEWEB)

Kim, Jae Yong; Lee, H. K.; Chun, Y. B.; Park, S. J.; Kim, B. G

2007-07-15

KAERI are developing the safety evaluation method and the analysis technology for high burn-up nuclear fuel rod that is the project, re-irradiation for re-instrumented fuel rod. That project includes insertion of a thermocouple in the center hole of PWR nuclear fuel rod with standard burn-up, 3,500{approx}4,000MWD/tU and then inspection of the nuclear fuel rod's heat performance during re-irradiation. To re-fabricate fuel rod, two devices are needed such as a drilling machine and a welding machine. The drilling machine performs grinding a center hole, 2.5 mm in diameter and 50 mm in depth, for inserting a thermocouple. And the welding machine is used to fasten a end plug on a fuel rod. Because these two equipment handle irradiated fuel rods, they are operated in hot cell blocked radioactive rays. Before inserting any device into hot cell, many tests with that machine have to be conducted. This report shows preliminary experiments for drilling a center hole on dummy of fuel rods and optimized drilling parameters to lessen operation time and damage of diamond dills. And the design method of a drilling machine for irradiated nuclear fuel rods and detail design drawings are attached.

Verification test of control rod system for HTR-10

International Nuclear Information System (INIS)

Zhou Huizhong; Diao Xingzhong; Huang Zhiyong; Cao Li; Yang Nianzu

2002-01-01

There are 10 sets of control rods and driving devices in 10 MW High Temperature Gas-cooled Test Reactor (HTR-10). The control rod system is the controlling and shutdown system of HTR-10, which is designed for reactor criticality, operation, and shutdown. In order to guarantee technical feasibility, a series of verification tests were performed, including room temperature test, thermal test, test after control rod system installed in HTR-10, and test of control rod system before HTR-10 first criticality. All the tests data showed that driving devices working well, control rods running smoothly up and down, random position settling well, and exactly position indicating

Turkey's response to threats of weapons of mass destruction

OpenAIRE

Al, Guray.

2001-01-01

Unlike most of its NATO allies, Turkey did not emerge from the Cold War with enhanced security. The acquisition of weapons of mass destruction (WMD) and ballistic missiles by its neighbors in the Middle Eastâ Iran, Iraq and Syriaâ creates a serious security concern for Turkey. This thesis analyzes the numerous threats posed to Turkey by its neighborsα nuclear, chemical and biological weapons programs and their ballistic missiles. It evaluates Turkeyαs defense options to counter these thre...

Recent incentives for renewable energy in Turkey

International Nuclear Information System (INIS)

Simsek, Hayal Ayca; Simsek, Nevzat

2013-01-01

Recently, the importance of renewable energy sources has increased significantly as climate change has become an important long term threat to global ecosystems and the world economy. In the face of increased concern about climate change and high fossil fuel costs together with a reduction in the primary energy sources such as oil, natural gas and coal, alternative energy sources (renewables) are increasingly needed to respond to the threat of climate change and growing energy demand in the world. Recent developments in Turkey, such as the liberalization of the electricity market and improvements in the renewable legislations, have accelerated the growth process and investment opportunities in the field of renewable energy. Turkey′s naturally endowed potential for renewables, such as solar, geothermal and wind, also accompanied these developments and attracted world attention to this market. In Turkey, renewable energy sources have gained great importance in the last decades due to growing energy demand and incentive policies which foster the utilization of renewable energy sources. This study aims to explore the availability and potential of renewable energy sources in Turkey and discuss the government policies and economic aspects. - highlights: • Turkey′s potential for renewable energy has attracted world attention. • Turkey has specific energy objectives in promoting renewable energy. • This paper evaluates recent incentives for renewable energy in Turkey. • Incentives in Turkey have led to more investment in renewable energy generation

Employment impacts of solar energy in Turkey

International Nuclear Information System (INIS)

Cetin, Muejgan; Egrican, Niluefer

2011-01-01

Solar energy is considered a key source for the future, not only for Turkey, also for all of the world. Therefore the development and usage of solar energy technologies are increasingly becoming vital for sustainable economic development. The main objective of this study is investigating the employment effects of solar energy industry in Turkey. Some independent reports and studies, which analyze the economic and employment impacts of solar energy industry in the world have been reviewed. A wide range of methods have been used in those studies in order to calculate and to predict the employment effects. Using the capacity targets of the photovoltaic (PV) and concentrated solar power (CSP) plants in the solar Roadmap of Turkey, the prediction of the direct and indirect employment impacts to Turkey's economy is possible. As a result, solar energy in Turkey would be the primary source of energy demand and would have a big employment effects on the economics. That can only be achieved with the support of governmental feed-in tariff policies of solar energy and by increasing research-development funds. - Highlights: → The objective of the study, is investigating employment effects of solar energy. → Using the capacity targets of the PV and CSP plants in solar roadmap of Turkey. → Direct employment has been calculated by constructing of the solar power plant. → If multiplier effect is accepted as 2, total employment will be doubled. → Validity of the figures depends on the government's policies.

Market Brief : Turkey oil and gas pipelines

International Nuclear Information System (INIS)

2001-08-01

This report presented some quick facts about oil and gas pipelines in Turkey and presented opportunities for trade. The key players and customers in the oil and gas sector were described along with an export check list. Turkey is looking into becoming an energy bridge between oil and gas producing countries in the Middle East, Central Asia and Europe. The oil and gas sectors are dominated by the Turkish Petroleum Corporation, a public enterprise dealing with exploration and production, and the State Pipeline Corporation which deals with energy transmission. They are also the key buyers of oil and gas equipment in Turkey. There are several pipelines connecting countries bordering the Caspian Sea. Opportunities exist in the areas of engineering consulting as well as contracting services for oil and gas pipeline transmission and distribution. Other opportunities lie in the area of pipeline construction, rehabilitation, materials, equipment, installation, and supervisory control and data acquisition (SCADA) systems. Currently, the major players are suppliers from Italy, Germany, France, United States and Japan. Turkey has no trade barriers and imported equipment and materials are not subjected to any restriction. The oil and gas market in Turkey expected in increase by an average annual growth rate of 15 per cent from 2001 to 2003. A brief description of pipeline projects in Turkey was presented in this report along with a list of key contacts and support services. 25 refs., 1 append

Numerical experiment designs. Study of vibratory behaviour of PWR'S control rod clusters

International Nuclear Information System (INIS)

Bosselut, D.; Soulier, B.; Regnier, G.

1997-01-01

The application of Experiment Design method to Finite Element Model (FEM) calculations is an original way of performing parametric studies. It has been used at EDF to simulate on a large parametric domain the vibrations of PWR's control rod cluster and to analyse the rod wear process. In the first part the FEM and the location of excitation sources are described. The calculated values are: rod displacement in the guiding cards, shock forces on the guiding cards and the wear power produced. In the second part, the computed Experiment Domain is described. This method approaches the response surface by a second degree polynomial. The retained model is composed for every parameters of all linear, quadratic and interaction terms (26 coefficients). In all, 34 polynomials have been built to approach the effective shock forces and the mean wear power at each of the 17 guiding points. In the third part the building of the computer Experiment Design is detailed: by Doehlert design adaptation to take into account a qualitative parameter, design optimization by adding four well chosen experiments and finally, design extension by passing from 4 to 6 parameters. In the last part, all the information deduced from application of this method are presented. The influence of parameters on calculated effective shock forces has been determined along rods and response surface have been easily approximated. The systematism and closeness of Experiment Design technique is underlined. Easy simulation of all the response domain by polynomial approach allows comparison with experimental results. (authors)

Development of a large scale structure in the rod gap region for turbulent in-line flow through closely spaced rod arrays

International Nuclear Information System (INIS)

Hooper, J.D.

1984-01-01

Experimental studies of developed axial single-phase flow through closely spaced rod arrays have shown, with reducing p/d ratio, the development of high axial and azimuthal turbulence intensities in the rod gap region. Associated with this is the existence of very high levels of the azimuthal Reynolds shear stress component either side of the rod gap centre. Spatial correlation analysis of the three turbulent velocity components has shown a large scale coherent and almost periodic structure in the rod gap region. The structure is markedly different to the currently accepted secondary flow model. 14 references

Low fluid level in pulse rod shock absorber

Energy Technology Data Exchange (ETDEWEB)

Aderhold, H. C.

1974-07-01

On various occasions during pulse mode operation the shim and regulating control rods would drop when the pulse rod was withdrawn. Subsequent investigation traced the problem to the pulse rod shock absorber which was found to be low in hydraulic fluid. The results of the investigation, the corrective action taken, and a method for measuring the shock absorber fluid level are presented. (author)

Summary of Skoda JS rod drop measurements analysis

International Nuclear Information System (INIS)

Svarny, J.; Krysl, V.

1999-01-01

A summary is presented of the Skoda JS rod drop reactivity measurements analysis provided during last two years based on control rod worth measurements by the outer ion chambers. Standard analysis based on comparisons of dynamics macrocode MOBY-DICK-SK and experimental data is extended to the 8-th group delayed neutron structure and new features of rod drop process are investigated. (author)

Low fluid level in pulse rod shock absorber

International Nuclear Information System (INIS)

Aderhold, H.C.

1974-01-01

On various occasions during pulse mode operation the shim and regulating control rods would drop when the pulse rod was withdrawn. Subsequent investigation traced the problem to the pulse rod shock absorber which was found to be low in hydraulic fluid. The results of the investigation, the corrective action taken, and a method for measuring the shock absorber fluid level are presented. (author)