Turbo-generator control with variable valve actuation

Science.gov (United States)

Vuk, Carl T [Denver, IA

2011-02-22

An internal combustion engine incorporating a turbo-generator and one or more variably activated exhaust valves. The exhaust valves are adapted to variably release exhaust gases from a combustion cylinder during a combustion cycle to an exhaust system. The turbo-generator is adapted to receive exhaust gases from the exhaust system and rotationally harness energy therefrom to produce electrical power. A controller is adapted to command the exhaust valve to variably open in response to a desired output for the turbo-generator.

An overview of turbo decoding on fading channels

OpenAIRE

ATILGAN, Doğan

2009-01-01

A review of turbo coding and decoding has been presented in the literature [1]. In that paper, turbo coding and decoding on AWGN (Additive White Gaussian Noise) channels has been elaborated. In wireless communications, a phenomennon called multipath fading is frequently encountered. Therefore, investigation of efficient techniques to tackle with the destructive effects of fading is essential. Turbo coding has been proven as an efficient channel coding technique for AWGN channels. Some of the ...

Forward error correction based on algebraic-geometric theory

CERN Document Server

A Alzubi, Jafar; M Chen, Thomas

2014-01-01

This book covers the design, construction, and implementation of algebraic-geometric codes from Hermitian curves. Matlab simulations of algebraic-geometric codes and Reed-Solomon codes compare their bit error rate using different modulation schemes over additive white Gaussian noise channel model. Simulation results of Algebraic-geometric codes bit error rate performance using quadrature amplitude modulation (16QAM and 64QAM) are presented for the first time and shown to outperform Reed-Solomon codes at various code rates and channel models. The book proposes algebraic-geometric block turbo codes. It also presents simulation results that show an improved bit error rate performance at the cost of high system complexity due to using algebraic-geometric codes and Chase-Pyndiah’s algorithm simultaneously. The book proposes algebraic-geometric irregular block turbo codes (AG-IBTC) to reduce system complexity. Simulation results for AG-IBTCs are presented for the first time.

La Turbo-Egalisation pour les transmission numériques à grande efficacité spectrale sur les canaux sélectifs en fréquence

OpenAIRE

Le Bidan , Raphaël

2003-01-01

This thesis deals with the problem of combining equalization with decoding for high data rate bandwidth-efficient transmissions over frequency-selective channels. Specifically, we focus on Turbo-Equalization which establishes an exchange of soft information between the equalizer and the decoder in an iterative manner. We first consider MAP turbo-equalizers which rely on trellis-based equalizers optimum in the sense of minimizing the symbol error probability. We show that these receivers achie...

Structural dynamics of turbo-machines

CERN Document Server

Rangwala, AS

2009-01-01

The book presents a detailed and comprehensive treatment of structural vibration evaluation of turbo-machines. Starting with the fundamentals of the theory of vibration as related to various aspects of rotating machines, the dynamic analysis procedures of a broad spectrum of turbo-machines is covered. An in-depth procedure for analyzing the torsional and flexural oscillations of the components and of the rotor-bearing system is presented. The latest trends in design and analysis are presented, chief among them: Blade and coupled disk-blade mod

Performance improvement of standard turbo-compressor; Han`yo turbo asshukuki no seino kaizen

Energy Technology Data Exchange (ETDEWEB)

Hokari, T.; Hasegawa, K.; Ozaki, S.; Majima, K. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

1999-05-01

Abradable materials are soft and cause no contact damage to the impeller of the turbo-compressor. Using such materials for the inlet casing facing to the impeller allows very small clearances between the impeller and inlet casing, thus improving the compressor efficiency by 10% over conventional types. Changing the area of abradable material applied to the inlet casing identified the optimum area in which decrease of the compressor surge margin is minimized and efficiency is improved by 10%. As a result, turbo-compressors have the best performance when the abradable materials are applied from the impeller outlet to two-thirds of the forward location of the inlet casing. (author)

Iterative Estimation in Turbo Equalization Process

Directory of Open Access Journals (Sweden)

MORGOS Lucian

2014-05-01

Full Text Available This paper presents the iterative estimation in turbo equalization process. Turbo equalization is the process of reception in which equalization and decoding are done together, not as separate processes. For the equalizer to work properly, it must receive before equalization accurate information about the value of the channel impulse response. This estimation of channel impulse response is done by transmission of a training sequence known at reception. Knowing both the transmitted and received sequence, it can be calculated estimated value of the estimated the channel impulse response using one of the well-known estimation algorithms. The estimated value can be also iterative recalculated based on the sequence data available at the output of the channel and estimated sequence data coming from turbo equalizer output, thereby refining the obtained results.

SYMBOL LEVEL DECODING FOR DUO-BINARY TURBO CODES

Directory of Open Access Journals (Sweden)

Yogesh Beeharry

2017-05-01

Full Text Available This paper investigates the performance of three different symbol level decoding algorithms for Duo-Binary Turbo codes. Explicit details of the computations involved in the three decoding techniques, and a computational complexity analysis are given. Simulation results with different couple lengths, code-rates, and QPSK modulation reveal that the symbol level decoding with bit-level information outperforms the symbol level decoding by 0.1 dB on average in the error floor region. Moreover, a complexity analysis reveals that symbol level decoding with bit-level information reduces the decoding complexity by 19.6 % in terms of the total number of computations required for each half-iteration as compared to symbol level decoding.

Progress of High Efficiency Centrifugal Compressor Simulations Using TURBO

Science.gov (United States)

Kulkarni, Sameer; Beach, Timothy A.

2017-01-01

Three-dimensional, time-accurate, and phase-lagged computational fluid dynamics (CFD) simulations of the High Efficiency Centrifugal Compressor (HECC) stage were generated using the TURBO solver. Changes to the TURBO Parallel Version 4 source code were made in order to properly model the no-slip boundary condition along the spinning hub region for centrifugal impellers. A startup procedure was developed to generate a converged flow field in TURBO. This procedure initialized computations on a coarsened mesh generated by the Turbomachinery Gridding System (TGS) and relied on a method of systematically increasing wheel speed and backpressure. Baseline design-speed TURBO results generally overpredicted total pressure ratio, adiabatic efficiency, and the choking flow rate of the HECC stage as compared with the design-intent CFD results of Code Leo. Including diffuser fillet geometry in the TURBO computation resulted in a 0.6 percent reduction in the choking flow rate and led to a better match with design-intent CFD. Diffuser fillets reduced annulus cross-sectional area but also reduced corner separation, and thus blockage, in the diffuser passage. It was found that the TURBO computations are somewhat insensitive to inlet total pressure changing from the TURBO default inlet pressure of 14.7 pounds per square inch (101.35 kilopascals) down to 11.0 pounds per square inch (75.83 kilopascals), the inlet pressure of the component test. Off-design tip clearance was modeled in TURBO in two computations: one in which the blade tip geometry was trimmed by 12 mils (0.3048 millimeters), and another in which the hub flow path was moved to reflect a 12-mil axial shift in the impeller hub, creating a step at the hub. The one-dimensional results of these two computations indicate non-negligible differences between the two modeling approaches.

Some problems raised by the operation of large nuclear turbo-generator sets. Automatic control system for steam turbo-generator units

International Nuclear Information System (INIS)

Cecconi, F.

1976-01-01

The design of an appropriate automatic system was found to be useful to improve the control of large size turbo-generator units so as to provide easy and efficient control and monitoring. The experience of the manufacturer of these turbo-generator units allowed a system well suited for this function to be designed [fr

Performance test of a ceramic turbo-viscous pump

International Nuclear Information System (INIS)

Abe, Tetsuya; Hiroki, Seiji; Murakami, Yoshio; Shiraishi, Shigeyuki; Totoura, Sadayuki; Ohtaki, Takashi.

1994-01-01

In the special fields of nuclear fusion facilities and semiconductor production installation, the development of new vacuum pumps which can cope with strong magnetic fields, high temperature gas and corrosive gas is demanded. Mitsubishi Heavy Industries Ltd. has advanced the development of ceramic turbo-molecular pumps and ceramic turbo-viscous pumps, which use ceramic rotors and gas bearings since 1985. The evaluation test of the ceramic turbo-viscous vacuum pump CT-3000H which can evacuate from atmospheric pressure to high vacuum with one pump was carried out, and the experimental results on the performance and the reliability were obtained, therefore, those are reported in this paper. The structure, specification and features of the CT-3000H are shown. The exhaust performance test of the pump was carried out in conformity with the standard of the Vacuum Society of Japan, JVIS 005 'Method of performance test for turbo-molecular pumps'. The gases used were nitrogen and helium. The results are shown. The exhaust test from atmospheric pressure was carried out by two methods, and the results are shown. (K.I.)

A Theoretical Framework for Soft-Information-Based Synchronization in Iterative (Turbo Receivers

Directory of Open Access Journals (Sweden)

Lottici Vincenzo

2005-01-01

Full Text Available This contribution considers turbo synchronization, that is to say, the use of soft data information to estimate parameters like carrier phase, frequency, or timing offsets of a modulated signal within an iterative data demodulator. In turbo synchronization, the receiver exploits the soft decisions computed at each turbo decoding iteration to provide a reliable estimate of some signal parameters. The aim of our paper is to show that such "turbo-estimation" approach can be regarded as a special case of the expectation-maximization (EM algorithm. This leads to a general theoretical framework for turbo synchronization that allows to derive parameter estimation procedures for carrier phase and frequency offset, as well as for timing offset and signal amplitude. The proposed mathematical framework is illustrated by simulation results reported for the particular case of carrier phase and frequency offsets estimation of a turbo-coded 16-QAM signal.

TurboTech Technical Evaluation Automated System

Science.gov (United States)

Tiffany, Dorothy J.

2009-01-01

TurboTech software is a Web-based process that simplifies and semiautomates technical evaluation of NASA proposals for Contracting Officer's Technical Representatives (COTRs). At the time of this reporting, there have been no set standards or systems for training new COTRs in technical evaluations. This new process provides boilerplate text in response to interview style questions. This text is collected into a Microsoft Word document that can then be further edited to conform to specific cases. By providing technical language and a structured format, TurboTech allows the COTRs to concentrate more on the actual evaluation, and less on deciding what language would be most appropriate. Since the actual word choice is one of the more time-consuming parts of a COTRs job, this process should allow for an increase in quantity of proposals evaluated. TurboTech is applicable to composing technical evaluations of contractor proposals, task and delivery orders, change order modifications, requests for proposals, new work modifications, task assignments, as well as any changes to existing contracts.

Leak detection in turbo group condensers using helium

International Nuclear Information System (INIS)

Gomez Cores, C.; Lloret, J.

1997-01-01

This method allows a rapid location of leaks (small or not) in the pipelines of a turbo group condenser, before opening the condenser boxes and no need of stooping the turbo group operation. This operation can last two hours maximum depending on the volume of the box or semi box. The technique consists of injecting helium into the water side and detecting it in the steam side, in the outlet of not condensable gases of the ejector. In the same way, probable air inlet to the condenser can be proved (auxiliary systems, turbo group joints to the condenser, etc.) in order to improve the vacuum and/or reduce the quantity of oxygen dissolved in the water of the steam side. (author) [es

Error-Rate Bounds for Coded PPM on a Poisson Channel

Science.gov (United States)

Moision, Bruce; Hamkins, Jon

2009-01-01

Equations for computing tight bounds on error rates for coded pulse-position modulation (PPM) on a Poisson channel at high signal-to-noise ratio have been derived. These equations and elements of the underlying theory are expected to be especially useful in designing codes for PPM optical communication systems. The equations and the underlying theory apply, more specifically, to a case in which a) At the transmitter, a linear outer code is concatenated with an inner code that includes an accumulator and a bit-to-PPM-symbol mapping (see figure) [this concatenation is known in the art as "accumulate-PPM" (abbreviated "APPM")]; b) The transmitted signal propagates on a memoryless binary-input Poisson channel; and c) At the receiver, near-maximum-likelihood (ML) decoding is effected through an iterative process. Such a coding/modulation/decoding scheme is a variation on the concept of turbo codes, which have complex structures, such that an exact analytical expression for the performance of a particular code is intractable. However, techniques for accurately estimating the performances of turbo codes have been developed. The performance of a typical turbo code includes (1) a "waterfall" region consisting of a steep decrease of error rate with increasing signal-to-noise ratio (SNR) at low to moderate SNR, and (2) an "error floor" region with a less steep decrease of error rate with increasing SNR at moderate to high SNR. The techniques used heretofore for estimating performance in the waterfall region have differed from those used for estimating performance in the error-floor region. For coded PPM, prior to the present derivations, equations for accurate prediction of the performance of coded PPM at high SNR did not exist, so that it was necessary to resort to time-consuming simulations in order to make such predictions. The present derivation makes it unnecessary to perform such time-consuming simulations.

Joint research for innovative turbo machines in power stations

Energy Technology Data Exchange (ETDEWEB)

Wiedermann, Alexander [MAN Diesel und Turbo SE, Oberhausen (Germany). AG Turbo; Jeschke, Peter [RWTH, Aachen (Germany). AG Turbo; Goldschmidt, Dirk [SIEMENS AG, Muelheim a.d. Ruhr (Germany). AG Turbo

2013-04-01

AG Turbo, established about 25 years ago, is a platform where pre-competitive, application-oriented turbo machinery research in Germany is agreed and coordinated. Focus of the research is on turbo machines which are responsible for energy conversion in conventional fossil-fired or combined cycle power plants (CCGT), as well as compressor trains for capturing and transporting the greenhouse gas CO{sub 2}. At all stages of the technical process - from gas compression through combustion in gas turbine combustors to expansion in the turbine - innovations are needed to actually meet the targets for efficiency, reliability, as well as protection of the climate and environment. Research results achieved will be presented using selected examples and an outlook at future activities will be given.

TurboFold: Iterative probabilistic estimation of secondary structures for multiple RNA sequences

Directory of Open Access Journals (Sweden)

Sharma Gaurav

2011-04-01

Full Text Available Abstract Background The prediction of secondary structure, i.e. the set of canonical base pairs between nucleotides, is a first step in developing an understanding of the function of an RNA sequence. The most accurate computational methods predict conserved structures for a set of homologous RNA sequences. These methods usually suffer from high computational complexity. In this paper, TurboFold, a novel and efficient method for secondary structure prediction for multiple RNA sequences, is presented. Results TurboFold takes, as input, a set of homologous RNA sequences and outputs estimates of the base pairing probabilities for each sequence. The base pairing probabilities for a sequence are estimated by combining intrinsic information, derived from the sequence itself via the nearest neighbor thermodynamic model, with extrinsic information, derived from the other sequences in the input set. For a given sequence, the extrinsic information is computed by using pairwise-sequence-alignment-based probabilities for co-incidence with each of the other sequences, along with estimated base pairing probabilities, from the previous iteration, for the other sequences. The extrinsic information is introduced as free energy modifications for base pairing in a partition function computation based on the nearest neighbor thermodynamic model. This process yields updated estimates of base pairing probability. The updated base pairing probabilities in turn are used to recompute extrinsic information, resulting in the overall iterative estimation procedure that defines TurboFold. TurboFold is benchmarked on a number of ncRNA datasets and compared against alternative secondary structure prediction methods. The iterative procedure in TurboFold is shown to improve estimates of base pairing probability with each iteration, though only small gains are obtained beyond three iterations. Secondary structures composed of base pairs with estimated probabilities higher than a

Turbo marketing through time compression.

Science.gov (United States)

Kotler, P; Stonich, P J

1991-01-01

A host of advantages will flow to companies that learn to make and deliver goods and services faster than their competitors. However, four key questions must be answered to determine if a turbo marketing approach is suitable for your company.

Turbo-SMT: Parallel Coupled Sparse Matrix-Tensor Factorizations and Applications

Science.gov (United States)

Papalexakis, Evangelos E.; Faloutsos, Christos; Mitchell, Tom M.; Talukdar, Partha Pratim; Sidiropoulos, Nicholas D.; Murphy, Brian

2016-01-01

How can we correlate the neural activity in the human brain as it responds to typed words, with properties of these terms (like ’edible’, ’fits in hand’)? In short, we want to find latent variables, that jointly explain both the brain activity, as well as the behavioral responses. This is one of many settings of the Coupled Matrix-Tensor Factorization (CMTF) problem. Can we enhance any CMTF solver, so that it can operate on potentially very large datasets that may not fit in main memory? We introduce Turbo-SMT, a meta-method capable of doing exactly that: it boosts the performance of any CMTF algorithm, produces sparse and interpretable solutions, and parallelizes any CMTF algorithm, producing sparse and interpretable solutions (up to 65 fold). Additionally, we improve upon ALS, the work-horse algorithm for CMTF, with respect to efficiency and robustness to missing values. We apply Turbo-SMT to BrainQ, a dataset consisting of a (nouns, brain voxels, human subjects) tensor and a (nouns, properties) matrix, with coupling along the nouns dimension. Turbo-SMT is able to find meaningful latent variables, as well as to predict brain activity with competitive accuracy. Finally, we demonstrate the generality of Turbo-SMT, by applying it on a Facebook dataset (users, ’friends’, wall-postings); there, Turbo-SMT spots spammer-like anomalies. PMID:27672406

Homotopy Analysis Method for Boundary-Value Problem of Turbo Warrant Pricing under Stochastic Volatility

Directory of Open Access Journals (Sweden)

Hoi Ying Wong

2013-01-01

Full Text Available Turbo warrants are liquidly traded financial derivative securities in over-the-counter and exchange markets in Asia and Europe. The structure of turbo warrants is similar to barrier options, but a lookback rebate will be paid if the barrier is crossed by the underlying asset price. Therefore, the turbo warrant price satisfies a partial differential equation (PDE with a boundary condition that depends on another boundary-value problem (BVP of PDE. Due to the highly complicated structure of turbo warrants, their valuation presents a challenging problem in the field of financial mathematics. This paper applies the homotopy analysis method to construct an analytic pricing formula for turbo warrants under stochastic volatility in a PDE framework.

Performance of Turbo Interference Cancellation Receivers in Space-Time Block Coded DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Emmanuel Oluremi Bejide

2008-07-01

Full Text Available We investigate the performance of turbo interference cancellation receivers in the space time block coded (STBC direct-sequence code division multiple access (DS-CDMA system. Depending on the concatenation scheme used, we divide these receivers into the partitioned approach (PA and the iterative approach (IA receivers. The performance of both the PA and IA receivers is evaluated in Rayleigh fading channels for the uplink scenario. Numerical results show that the MMSE front-end turbo space-time iterative approach receiver (IA effectively combats the mixture of MAI and intersymbol interference (ISI. To further investigate the possible achievable data rates in the turbo interference cancellation receivers, we introduce the puncturing of the turbo code through the use of rate compatible punctured turbo codes (RCPTCs. Simulation results suggest that combining interference cancellation, turbo decoding, STBC, and RCPTC can significantly improve the achievable data rates for a synchronous DS-CDMA system for the uplink in Rayleigh flat fading channels.

Turbo decoder architecture for beyond-4G applications

CERN Document Server

Wong, Cheng-Chi

2013-01-01

This book describes the most recent techniques for turbo decoder implementation, especially for 4G and beyond 4G applications. The authors reveal techniques for the design of high-throughput decoders for future telecommunication systems, enabling designers to reduce hardware cost and shorten processing time. Coverage includes an explanation of VLSI implementation of the turbo decoder, from basic functional units to advanced parallel architecture. The authors discuss both hardware architecture techniques and experimental results, showing the variations in area/throughput/performance with respec

Space-Time Turbo Trellis Coded Modulation for Wireless Data Communications

Directory of Open Access Journals (Sweden)

Welly Firmanto

2002-05-01

Full Text Available This paper presents the design of space-time turbo trellis coded modulation (ST turbo TCM for improving the bandwidth efficiency and the reliability of future wireless data networks. We present new recursive space-time trellis coded modulation (STTC which outperform feedforward STTC proposed in by Tarokh et al. (1998 and Baro et al. (2000 on slow and fast fading channels. A substantial improvement in performance can be obtained by constructing ST turbo TCM which consists of concatenated recursive STTC, decoded by iterative decoding algorithm. The proposed recursive STTC are used as constituent codes in this scheme. They have been designed to satisfy the design criteria for STTC on slow and fast fading channels, derived for systems with the product of transmit and receive antennas larger than 3. The proposed ST turbo TCM significantly outperforms the best known STTC on both slow and fast fading channels. The capacity of this scheme on fast fading channels is less than 3 dB away from the theoretical capacity bound for multi-input multi-output (MIMO channels.

Digital and analog communication systems

Science.gov (United States)

Shanmugam, K. S.

1979-01-01

The book presents an introductory treatment of digital and analog communication systems with emphasis on digital systems. Attention is given to the following topics: systems and signal analysis, random signal theory, information and channel capacity, baseband data transmission, analog signal transmission, noise in analog communication systems, digital carrier modulation schemes, error control coding, and the digital transmission of analog signals.

The operator model as a framework of research on errors and temporal, qualitative and analogical reasoning

International Nuclear Information System (INIS)

Decortis, F.; Drozdowicz, B.; Masson, M.

1990-01-01

In this paper the needs and requirements for developing a cognitive model of a human operator are discussed and the computer architecture, currently being developed, is described. Given the approach taken, namely the division of the problem into specialised tasks within an area and using the architecture chosen, it is possible to build independently several cognitive and psychological models such as errors and stress models, as well as models of temporal, qualitative and an analogical reasoning. (author)

A channel multiplexing for the analog input channel of the advantech PCL-718 ADC-12 bit by using PCLD-889 programmable ampliplexer / multiplexer board have been done

International Nuclear Information System (INIS)

Sudiyanto; Aminus, S; Sujono, Djoko; Ngatinu; Sudaryanto; Wiyana, Badi

1996-01-01

A channel multiplexing for the analog input channels of the Advantech PCL-718 ADC-12 bit by using PCLD-889 programmable Amplifier / multiplexer board have been done. The experiments have been prepared by using Turbo-C software where every PCLD-889 board multiplexes 16 differential input channels into one analog output channel, up to 10 PCLD-889 can be cascaded to expand the analog input of PCL-718 ADC-12 bit to 8 x 16 channels

Interleaver Design for Turbo Coding

DEFF Research Database (Denmark)

Andersen, Jakob Dahl; Zyablov, Viktor

1997-01-01

By a combination of construction and random search based on a careful analysis of the low weight words and the distance properties of the component codes, it is possible to find interleavers for turbo coding with a high minimum distance. We have designed a block interleaver with permutations...

An Off-Grid Turbo Channel Estimation Algorithm for Millimeter Wave Communications

Directory of Open Access Journals (Sweden)

Lingyi Han

2016-09-01

Full Text Available The bandwidth shortage has motivated the exploration of the millimeter wave (mmWave frequency spectrum for future communication networks. To compensate for the severe propagation attenuation in the mmWave band, massive antenna arrays can be adopted at both the transmitter and receiver to provide large array gains via directional beamforming. To achieve such array gains, channel estimation (CE with high resolution and low latency is of great importance for mmWave communications. However, classic super-resolution subspace CE methods such as multiple signal classification (MUSIC and estimation of signal parameters via rotation invariant technique (ESPRIT cannot be applied here due to RF chain constraints. In this paper, an enhanced CE algorithm is developed for the off-grid problem when quantizing the angles of mmWave channel in the spatial domain where off-grid problem refers to the scenario that angles do not lie on the quantization grids with high probability, and it results in power leakage and severe reduction of the CE performance. A new model is first proposed to formulate the off-grid problem. The new model divides the continuously-distributed angle into a quantized discrete grid part, referred to as the integral grid angle, and an offset part, termed fractional off-grid angle. Accordingly, an iterative off-grid turbo CE (IOTCE algorithm is proposed to renew and upgrade the CE between the integral grid part and the fractional off-grid part under the Turbo principle. By fully exploiting the sparse structure of mmWave channels, the integral grid part is estimated by a soft-decoding based compressed sensing (CS method called improved turbo compressed channel sensing (ITCCS. It iteratively updates the soft information between the linear minimum mean square error (LMMSE estimator and the sparsity combiner. Monte Carlo simulations are presented to evaluate the performance of the proposed method, and the results show that it enhances the angle

Analog and digital dividers for mass spectrometers

International Nuclear Information System (INIS)

Osipov, A.K.

1980-01-01

Errors of four different types of stress dividers used in statical mass-spectrometers for determination of mass number by accelerating stress are analyzed. The simplest flowsheet of the analog divider comprises operation amplifier, in the chain of the negative feedback of which a multiplication device on differential cascade is switched- in. This analog divider has high sensitivity to temperature and high error approximately 5%. Application of the multiplier on differential cascade with normalization permits to increase temperature stability and decrease the error up to 1%. Another type of the analog divider is a logarithmic divider the error of which is constant within the whole operation range and it constitutes 1-5%. The digital divider with a digital-analog transformer (DAT) has the error of +-0.015% which is determined by the error of detectors and resistance of keys in the locked state. Considered is the design of a divider based on transformation of the inlet stress into the time period. The error of the divider is determined in this case mainly by stress of the zero shift of the operation amplifier (it should be compensated) and relative threshold stability of the comparator triggering which equals (2-3)x10 -4 . It is noted that the divider with DAT application and the divider with the use of stress transformation within the time period are most perspective ones for statical mass-spectrometers [ru

Turbo FRMAC 2018

Energy Technology Data Exchange (ETDEWEB)

2017-11-30

The Turbo FRMAC (TF) software program is the software implementation of the science and methodologies utilized in the Federal Radiological Monitoring and Assessment Center (FRMAC). The software automates the calculations described in volumes 1 of "The Federal Manual for Assessing Environmental Data during a Radiological Emergency" (2015 version). In the event of the intentional or accidental release of radioactive material, the software is used to guide and govern the response of the Federal, State, Local, and Tribal governments. The manual, upon which the software is based, is unclassified and freely available on the Internet.

The LHCb Turbo stream

Energy Technology Data Exchange (ETDEWEB)

Puig, A., E-mail: albert.puig@cern.ch

2016-07-11

The LHCb experiment will record an unprecedented dataset of beauty and charm hadron decays during Run II of the LHC, set to take place between 2015 and 2018. A key computing challenge is to store and process this data, which limits the maximum output rate of the LHCb trigger. So far, LHCb has written out a few kHz of events containing the full raw sub-detector data, which are passed through a full offline event reconstruction before being considered for physics analysis. Charm physics in particular is limited by trigger output rate constraints. A new streaming strategy includes the possibility to perform the physics analysis with candidates reconstructed in the trigger, thus bypassing the offline reconstruction. In the Turbo stream the trigger will write out a compact summary of physics objects containing all information necessary for analyses. This will allow an increased output rate and thus higher average efficiencies and smaller selection biases. This idea will be commissioned and developed during 2015 with a selection of physics analyses. It is anticipated that the turbo stream will be adopted by an increasing number of analyses during the remainder of LHC Run II (2015–2018) and ultimately in Run III (starting in 2020) with the upgraded LHCb detector.

Turbo Equalization for Digital Coherent Receivers

DEFF Research Database (Denmark)

Arlunno, Valeria; Caballero Jambrina, Antonio; Borkowski, Robert

2014-01-01

. In this paper, it is demonstrated that Turbo Equalization routines can be used to mitigate performance degradations stemming from optical fiber propagation effects both in optical fiber dispersion managed and unmanaged coherent detection links. The effectiveness of this solution is analyzed both numerically...

A Low-Complexity UEP Methodology Demonstrated on a Turbo-Encoded Wavelet Image Satellite Downlink

Directory of Open Access Journals (Sweden)

Salemi Eric

2008-01-01

Full Text Available Realizing high-quality digital image transmission via a satellite link, while optimizing resource distribution and minimizing battery consumption, is a challenging task. This paper describes a methodology to optimize a turbo-encoded wavelet-based satellite downlink progressive image transmission system with unequal error protection (UEP techniques. To achieve that goal, we instantiate a generic UEP methodology onto the system, and demonstrate that the proposed solution has little impact on the average performance, while greatly reducing the run-time complexity. Based on a simple design-time distortion model and a low-complexity run-time algorithm, the provided solution can dynamically tune the system's configuration to any bitrate constraint or channel condition. The resulting system outperforms in terms of peak signal-to-noise ratio (PSNR, a state-of-the-art, fine-tuned equal error protection (EEP solution by as much as 2 dB.

A Low-Complexity UEP Methodology Demonstrated on a Turbo-Encoded Wavelet Image Satellite Downlink

Directory of Open Access Journals (Sweden)

Eric Salemi

2008-01-01

Full Text Available Realizing high-quality digital image transmission via a satellite link, while optimizing resource distribution and minimizing battery consumption, is a challenging task. This paper describes a methodology to optimize a turbo-encoded wavelet-based satellite downlink progressive image transmission system with unequal error protection (UEP techniques. To achieve that goal, we instantiate a generic UEP methodology onto the system, and demonstrate that the proposed solution has little impact on the average performance, while greatly reducing the run-time complexity. Based on a simple design-time distortion model and a low-complexity run-time algorithm, the provided solution can dynamically tune the system's configuration to any bitrate constraint or channel condition. The resulting system outperforms in terms of peak signal-to-noise ratio (PSNR, a state-of-the-art, fine-tuned equal error protection (EEP solution by as much as 2 dB.

Development and tests of large nuclear turbo-generator welded rotors

International Nuclear Information System (INIS)

Colombie, H.; Thiery, M.; Rotzinger, R.; Pelissou, C.; Tabacco, C.; Fernagut, V.

2015-01-01

Turbo-generators require large forgings for the rotor and it is a worldwide practice to manufacture turbo-generator rotor bodies as single piece forgings. Rotors for nuclear applications (4-pole rotors design, 1500/1800 rpm) require forgings of up to 2.0 m diameter and ultra large ingots with weight more than 500 tons. Nowadays only few forge masters can deliver such forgings in the world. Based on the large welding experience Alstom has gained over decades on steam and gas turbines and Alstom's multi piece shrunk turbo-generator rotors, it was suggested to manufacture 4-pole turbo-generator rotors by welding the shaft from aligned cylindrical forgings. Compared to turbine welded rotors, the shaft of a turbo-generator rotor presents differences linked to dimensions/weight, weld depth and electrical application. The manufacture of a 2 disc model allowed to prove through electrical and mechanical analysis the reliability of the concept as well as the reliability of the manufacturing processes through material tests, micro sections, electrical component tests, weld geometry, welding processes (TIG,SAW,...), weld inspection (Ultrasonic testing, radiographic inspection,...) weld heat treatments and machining. Then a full rotor able to replace a single forging rotor was manufactured in order to validate and prove to potential customers the validity of the welded rotor technology. During the first order from EDF of a welded 900 MW spare rotor, the procedure for the Non Destructive Test on a slotted rotor was developed upon EDF request in order to compare future Non Destructive Testing with the finger print of the new rotor. This complete rotor was delivered to EDF in January 2013. This rotor is in operation in a nuclear unit since November 2013. (authors)

EXPANSION OF TURBO PROLOGUE PROGRAMMING SYSTEM BY PREDICATES FOR LIST PROCESSING

Directory of Open Access Journals (Sweden)

A. T. Kovalkov

2008-01-01

Full Text Available Lists are considered as a main data structure in logic Turbo Prologue programming language. However the language does not contain in-set predicates (procedures for list processing. In order to facilitate a problem programming process where lists are used it is proposed to apply a Turbo Prologue version that has a set of predicates in the form of recursive rules for executing frequently repeated operations with lists such as unification of lists, italicization and deletion of some list elements, sorting-out, list reversing and many others. The modified version contains a reference to new input predicates. The proposed Turbo Prologue version is easily expanded by new rules. Usage of this version makes programmer’s work easier and promotes development of new programs where it is necessary to work with lists.

Design and Development of a 200-kW Turbo-Electric Distributed Propulsion Testbed

Science.gov (United States)

Papathakis, Kurt V.

2017-01-01

There a few NASA funded electric and hybrid electric projects from different NASA Centers, including the NASA Armstrong Flight Research Center (AFRC) (Edwards, California). Each project identifies a specific technology gap that is currently inhibiting the growth and proliferation of relevant technologies in commercial aviation. This paper describes the design and development of a turbo-electric distributed propulsion (TeDP) hardware-in-the-loop (HIL) simulation bench, which is a test bed for discovering turbo-electric control, distributed electric control, power management control, and integration competencies while providing risk mitigation for future turbo-electric flying demonstrators.

Pico-coulomb charge measured at BELLA to percent-level precision using a Turbo-ICT

International Nuclear Information System (INIS)

Nakamura, K; Mittelberger, D E; Gonsalves, A J; Daniels, J; Mao, H-S; Leemans, W P; Stulle, F; Bergoz, J

2016-01-01

Precise diagnostics of picocoulomb level particle bunches produced by laser plasma accelerators (LPAs) can be a significant challenge. Without proper care, the small signals associated with such bunches can be dominated by a background generated by laser, target, laser–plasma interaction and particle induced radiation. In this paper, we report on first charge measurements using the newly developed Turbo-ICT for LPAs. We outline the Turbo-ICT working principle, which allows precise sub-picocoulomb measurements even in the presence of significant background signals. A comparison of the Turbo-ICT, a conventional integrating current transformer (ICT) and a scintillating screen (Lanex) was carried out at the Berkeley Lab Laser Accelerator. Results show that the Turbo-ICT can measure sub-picocoulomb charge accurately and has significantly improved noise immunity compared to the ICT. (paper)

Pico-coulomb charge measured at BELLA to percent-level precision using a Turbo-ICT

Science.gov (United States)

Nakamura, K.; Mittelberger, D. E.; Gonsalves, A. J.; Daniels, J.; Mao, H.-S.; Stulle, F.; Bergoz, J.; Leemans, W. P.

2016-03-01

Precise diagnostics of picocoulomb level particle bunches produced by laser plasma accelerators (LPAs) can be a significant challenge. Without proper care, the small signals associated with such bunches can be dominated by a background generated by laser, target, laser-plasma interaction and particle induced radiation. In this paper, we report on first charge measurements using the newly developed Turbo-ICT for LPAs. We outline the Turbo-ICT working principle, which allows precise sub-picocoulomb measurements even in the presence of significant background signals. A comparison of the Turbo-ICT, a conventional integrating current transformer (ICT) and a scintillating screen (Lanex) was carried out at the Berkeley Lab Laser Accelerator. Results show that the Turbo-ICT can measure sub-picocoulomb charge accurately and has significantly improved noise immunity compared to the ICT.

A 220 MVA turbo-generator for the TCV tokamak power supplies

International Nuclear Information System (INIS)

Perez, A.; Canay, I.M.; Simond, J.-J.; Morf, J.-J; Pahud, J.-D; Seysen, R.

1989-01-01

A new 220 MVA, 120 Hz, 4 pole turbo-generator will be used as a pulsed power source to supply the toroidal and poloidal power supplies of the TCV tokamak, which is being built at the Ecole Polytechnique Federale de Lausanne in Switzerland. The paper describes the particular requirements of the TCV poloidal power supplies and the main electrical and mechanical features of the turbo-generator and its principal auxillaries. (author). 6 figs.; 1 tab

Counteracting 16-QAM Optical Fiber Transmission Impairments With Iterative Turbo Equalization

DEFF Research Database (Denmark)

Arlunno, Valeria; Caballero Jambrina, Antonio; Borkowski, Robert

2013-01-01

A turbo equalization (TE) scheme based on convolutional code and normalized least mean square equalizer for coherent optical communication links is proposed and experimentally demonstrated. The proposed iterative TE technique is proved effective for counteracting polarization-division-multiplexin......A turbo equalization (TE) scheme based on convolutional code and normalized least mean square equalizer for coherent optical communication links is proposed and experimentally demonstrated. The proposed iterative TE technique is proved effective for counteracting polarization...

Non-analog Monte Carlo estimators for radiation momentum deposition

International Nuclear Information System (INIS)

Hykes, Joshua M.; Densmore, Jeffery D.

2009-01-01

The standard method for calculating radiation momentum deposition in Monte Carlo simulations is the analog estimator, which tallies the change in a particle's momentum at each interaction with the matter. Unfortunately, the analog estimator can suffer from large amounts of statistical error. In this paper, we present three new non-analog techniques for estimating momentum deposition. Specifically, we use absorption, collision, and track-length estimators to evaluate a simple integral expression for momentum deposition that does not contain terms that can cause large amounts of statistical error in the analog scheme. We compare our new non-analog estimators to the analog estimator with a set of test problems that encompass a wide range of material properties and both isotropic and anisotropic scattering. In nearly all cases, the new non-analog estimators outperform the analog estimator. The track-length estimator consistently yields the highest performance gains, improving upon the analog-estimator figure of merit by factors of up to two orders of magnitude.

LHCb Turbo++ Slimming: Inclusive B Hadron Decay Product Selection

CERN Document Server

Bogensberger, David

2016-01-01

My summer student project focused on reducing the turbo++ output bandwidth for B meson decays at LHCb. The aim is to discard as many of the background tracks as possible, while still retaining almost all of the signal events. I analysed the ability to distinguish signal from background tracks, by considering four different B meson decays, while using signal definitions for just one particular decay, as well as for a general type of decay. I added tracks to a triggered turbo candidate, to reconstruct the B meson. I used a boosted decision tree and an artificial neural network to classify events, and compared the resulting ROC curves.

First-pass myocardial perfusion MR imaging with gadolinium-enhanced turbo FLASH

International Nuclear Information System (INIS)

Teresi, L.M.; Smith, C.; Messenger, J.; Watanabe, A.; Herbst, M.; O'Sullivan, R.M.; Lee, R.; Remer, J.; Rappaport, A.; Bradley, W.G.

1990-01-01

This paper determines the efficacy of MR first-pass myocardial perfusion imaging using gadolinium-enhanced Turbo--fast low-angle shot (FLASH) ultrafast imaging combined with MR systolic wall thickening data for the determination of myocardial viability. Five normal volunteers and five patients with remote myocardial infarction were studied on a 1.5-T imaging system (Siemans, Ehrlangen, NJ). Turbo-FLASH imaging utilized a 180 degrees inversion pulse followed by a rapid gradient-echo sequence (TI 400 msec, TE2 msec, TR 4.9 msec, FA 8 degrees) with a complete 64 x 64 matrix image (300 mm FOV) being acquired in 300 msec. First-pass myocardial perfusion imaging was performed in the short-axis and long-axis oblique projections with a concantenated series of Turbo-FLASH images triggered to end-systole acquired immediately before and during a rapid bolus injection of 5cc gadolinium-DTPA

Quadrature Errors and DC Offsets Calibration of Analog Complex Cross-Correlator for Interferometric Passive Millimeter-Wave Imaging Applications

Directory of Open Access Journals (Sweden)

Chao Wang

2018-02-01

Full Text Available The design and calibration of the cross-correlator are crucial issues for interferometric imaging systems. In this paper, an analog complex cross-correlator with output DC offsets and amplitudes calibration capability is proposed for interferometric passive millimeter-wave security sensing applications. By employing digital potentiometers in the low frequency amplification circuits of the correlator, the outputs characteristics of the correlator could be digitally controlled. A measurement system and a corresponding calibration scheme were developed in order to eliminate the output DC offsets and the quadrature amplitude error between the in-phase and the quadrature correlating subunits of the complex correlator. By using vector modulators to provide phase controllable correlated noise signals, the measurement system was capable of obtaining the output correlation circle of the correlator. When injected with −18 dBm correlated noise signals, the calibrated quadrature amplitude error was 0.041 dB and the calibrated DC offsets were under 26 mV, which was only 7.1% of the uncalibrated value. Furthermore, we also described a quadrature errors calibration algorithm in order to estimate the quadrature phase error and in order to improve the output phase accuracy of the correlator. After applying this calibration, we were able to reduce the output phase error of the correlator to 0.3°.

Preliminary Validation and Verification of TURBO{sub D}ESIGN for S-CO{sub 2} Axial Compressor

Energy Technology Data Exchange (ETDEWEB)

Lee, Je Kyoung; Lee, Jeong Ik; Ahn, Yoon Han; Kim, Seong Gu [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Yoon, Ho Joon; Addad, Yacine [Khalifa University of Science, Technology and Research, Abu Dhabi (United Arab Emirates)

2012-05-15

To use the advantages of Supercritical CO{sub 2}(S-CO{sub 2}) Brayton cycle for nuclear power plant, KAIST-Khalifa University joint research team has been focusing on S-CO{sub 2} turbomachinery development. TURBO{sub D}ESIGN code is one of the products of our researches to design a turbomachinery. The major feature of TURBO{sub D}ESIGN is that the formulation is based on the real gas and none of the ideal gas assumption was applied to the code. Thus, TURBO{sub D}ESIGN has high flexibility regarding the type of gases. In this paper, preliminary code validation and verification of TURBO{sub D}ESIGN will be discussed for axial type compressor design

Optimization design of turbo-expander gas bearing for a 500W helium refrigerator

Science.gov (United States)

Li, S. S.; Fu, B.; Y Zhang, Q.

2017-12-01

Turbo-expander is the core machinery of the helium refrigerator. Bearing as the supporting element is the core technology to impact the design of turbo-expander. The perfect design and performance study for the gas bearing are essential to ensure the stability of turbo-expander. In this paper, numerical simulation is used to analyze the performance of gas bearing for a 500W helium refrigerator turbine, and the optimization design of the gas bearing has been completed. And the results of the gas bearing optimization have a guiding role in the processing technology. Finally, the turbine experiments verify that the gas bearing has good performance, and ensure the stable operation of the turbine.

Introduction to littoral erosion problem in Uraba (Arboletes-Turbo area) Colombian Caribbean Coast

International Nuclear Information System (INIS)

Correa; Ivan D; Vernette, Georges

2004-01-01

Shoreline retreat has been the net dominant historical trend along the 145 km-length littoral between Arboletes and Turbo (southern Caribbean of Colombia). For the last four decades, there were identified in this littoral shoreline retreat of about 50-100 m in several places (Uveros, Damaquiel, Zapata, Turbo) and a maximum of 1.6 km in the Punta Rey-Arboletes area, where land losses were of 4.5 km 2 , at exceptional rates of 40 rn/year. The synthesis of the available information suggest that the general susceptibility to erosion between Arboletes and turbo could be related primarily to relative sea level rise, associated to tectonic movements as well as to the effects of mud diapirism and hydroisostacy. In the more critical areas (Arboletes, Turbo), the natural erosive trends were accelerated by anthropic actions, including river diversion (Turbo), beach mining and inadequate (or total absence) practices for controlling residual and natural waters. Up to august 2000, there were invested about $ Col 10.000 billions in 155 engineering defenses (groins, sea walls and rip-rap which totalize 6.2 km of total length and a volume of materials of 37.000 m 3 ). With few exceptions, groins have not been successful and are now part of the problem, accelerating shore erosion along the adjacent sectors. In the short term, the littoral erosion between Arboletes and turbo is caused both by marine and by sub aerial factors. it is facilitated by the poor lithological strengths of cliffs and marine terraces, mainly composed of highly fractured and weathered claystones and mudstones (with stratification and weakness planes dipping toward sea) and non-consolidated, easily liquefacted, fine sediments; both conditions facilitate the occurrence of rocks falls, slides and mud flows that result in high figures of cliff retreat (3 to 4 m), specially during the first 15 days of the summer-winter transition (April) and in high waves periods. The case of the littoral erosion between Arboletes

Electric Turbo Pump

Science.gov (United States)

Steckler, Jessica

2017-01-01

NASA is working in junction with another company on the Electric Turbo Pump. Analysis of the impeller, including the blades, volute housing, and associated components, will take place in ANSYS. Contours of the deformed and stress were recorded to assess the parts. Campbell diagrams will be considered as mentioned to find the operating regions of the impeller and volute housing, more specifically what speed is ideal to ensure that the impeller does not begin to vibrate at a frequency that will break it. More than one material will be examined as per request by the designer to determine which material is more cost efficient, easy to machine, and can withstand the stress values that will be placed on it.

ABB Turbo advanced fuel for application in System 80 family of plants

International Nuclear Information System (INIS)

Karoutas, Z.E.; Dixon, D.J.; Shapiro, N.L.

1998-01-01

ABB Combustion Engineering Nuclear Operations (ABB CE) has developed an Advanced Fuel Design, tailored to the Combustion Engineering, Inc. (CE) Nuclear Steam Supply System (NSSS) environment. This Advanced Fuel Design called Turbo features a full complement of innovative components, including GUARDIAN debris-resistant spacer grids, Turbo Zircaloy mixing grids to increase thermal margin and grid-to-rod fretting resistance, value-added fuel pellets to increase fuel loading, advanced cladding to increase achievable burnup, and axial blankets and Erbium integral burnable absorbers for improving fuel cycle economics. This paper summarizes the Turbo Fuel Design and its application to a System 80 family type plant. Benefits in fuel reliability, thermal margin, improved fuel cycle economics and burn up capability are compared relative to the current ABB CE standard fuel design. The fuel management design and the associated thermal margin are also evaluated. (author)

The influence of the analog-to-digital conversion error on the JT-60 plasma position/shape feedback control system

International Nuclear Information System (INIS)

Yoshida, Michiharu; Kurihara, Kenichi

1995-12-01

In the plasma feedback control system (PFCS) and the direct digital controller (DDC) for the poloidal field coil power supply in the JT-60 tokamak, it is necessary to observe signals of all the poloidal field coil currents. Each of the signals, originally measured by a single sensor, is distributed to the PFCS and DDC through different cable routes and different analog-to-digital converters from each other. This produces the conversion error to the amount of several bits. Consequently, proper voltage from feedback calculation cannot be applied to the coil, and hence the control performance is possibly supposed to deteriorate to a certain extent. This paper describes how this error makes an influence on the plasma horizontal position control and how to improve the deteriorated control performance. (author)

List manipulation in Turbo Prolog

Directory of Open Access Journals (Sweden)

V.Cotelea

1995-06-01

Full Text Available The present paper is concerned with list processing in Turbo Prolog language. It doesn't claim to be an exhaustive description of operations which can be performed upon lists. Nevertheless adduced programs are most representative, more or less known to specialists in logic programming domain. By means of examples are explained the list manipulation techniques, use of recursion, declarative comparison of predicates, analysis and fixation of acceptable prototypes and some problems of predicates' inconsistency. Index terms. Prolog, list, recursion.

Study of two-stage turbine characteristic and its influence on turbo-compound engine performance

International Nuclear Information System (INIS)

Zhao, Rongchao; Zhuge, Weilin; Zhang, Yangjun; Yang, Mingyang; Martinez-Botas, Ricardo; Yin, Yong

2015-01-01

Highlights: • An analytical model was built to study the interactions between two turbines in series. • The impacts of HP VGT and LP VGT on turbo-compound engine performance were investigated. • The fuel reductions obtained by HP VGT at 1900 rpm and 1000 rpm are 3.08% and 7.83% respectively. • The optimum value of AR ranged from 2.0 to 2.5 as the turbo-compound engine speed decreases. - Abstract: Turbo-compounding is an effective way to recover waste heat from engine exhaust and reduce fuel consumption for internal combustion engine (ICE). The characteristics of two-stage turbine, including turbocharger turbine and power turbine, have significant effects on the overall performance of turbo-compound engine. This paper investigates the interaction between two turbines in a turbo-compound engine and its impact on the engine performance. Firstly an analytical model is built to investigate the effects of turbine equivalent flow area on the two-stage turbine characteristics, including swallowing capacity and load split. Next both simulation and experimental method are carried out to study the effects of high pressure variable geometry turbine (HP VGT), low pressure variable geometry turbine (LP VGT) and combined VGT on the engine overall performance. The results show that the engine performance is more sensitive to HP VGT compared with LP VGT at all the operation conditions, which is caused by the larger influences of HP VGT on the total expansion ratio and engine air–fuel ratio. Using the HP VGT method, the fuel reductions of the turbo-compound engine at 1900 rpm and 1000 rpm are 3.08% and 7.83% respectively, in comparison with the baseline engine. The corresponding optimum values of AR are 2.0 and 2.5

Changes in analogical reasoning in adulthood.

Science.gov (United States)

Clark, E; Gardner, M K; Brown, G; Howell, R J

1990-01-01

This study sought to investigate adult intellectual development through an analysis of a particular type of cognitive ability, verbal analogical reasoning. The performance of 60 individuals between the ages of 20 and 79 was compared on 100 verbal analogies. The subjects consisted of six groups of ten individuals each (five males and five females), matched as a group for education and gender. Solution times and error rates served as the dependent measures. Results showed that there was a significant trend for the older subjects (60- and 70-year-olds) to be slower than the young subjects (20-, 30-, 40-, and 50-year-olds), but not necessarily more error prone. These data suggest that verbal analogical reasoning changes with age. Supplemental data demonstrated a change in other abilities as well (i.e., decline in perceptual-motor speed and spatial skill).

High-Speed Turbo-TCM-Coded Orthogonal Frequency-Division Multiplexing Ultra-Wideband Systems

Directory of Open Access Journals (Sweden)

Wang Yanxia

2006-01-01

Full Text Available One of the UWB proposals in the IEEE P802.15 WPAN project is to use a multiband orthogonal frequency-division multiplexing (OFDM system and punctured convolutional codes for UWB channels supporting a data rate up to 480 Mbps. In this paper, we improve the proposed system using turbo TCM with QAM constellation for higher data rate transmission. We construct a punctured parity-concatenated trellis codes, in which a TCM code is used as the inner code and a simple parity-check code is employed as the outer code. The result shows that the system can offer a much higher spectral efficiency, for example, 1.2 Gbps, which is 2.5 times higher than the proposed system. We identify several essential requirements to achieve the high rate transmission, for example, frequency and time diversity and multilevel error protection. Results are confirmed by density evolution.

Analogical reasoning abilities of recovering alcoholics.

Science.gov (United States)

Gardner, M K; Clark, E; Bowman, M A; Miller, P J

1989-08-01

This study investigated analogical reasoning abilities of alcoholics who had been abstinent from alcohol for at least 1 year. Their performance was compared to that of nonalcoholic controls matched as a group for education, age, and gender. Solution times and error rates were modeled using a regression model. Results showed a nonsignificant trend for alcoholics to be faster, but more error prone, than controls. The same componential model applied to both groups, and fit them equally well. Although differences have been found in analogical reasoning ability between controls and alcoholics immediately following detoxification, we find no evidence of differences after extended periods of sobriety.

The experimental study on efficiency improvement of turbo machinery supported with magnetic bearings

International Nuclear Information System (INIS)

Park, In Hwang; Park, Young Ho; Han, Dong Chul

2007-01-01

To implement a conventional electromagnetic bearing in small turbo machinery, it has problems such as load capacity and size. Therefore, in this paper, these problems are resolved by using a permanent magnet biased electromagnetic bearing as a thrust bearing of small turbo machinery. Because the flux path of the bearing is designed by reluctance path modulation using an electromagnet and a permanent magnet, the bearing improves upon non-linearity, power consumption, size and load capacity of a conventional electromagnetic bearing. Test rotating the shaft over 500,000DN were carried out to verify the performance of the proposed small turbo machinery. In addition, the relationships between mass flow rate and pressure rise were measured as changing the tip clearance to verify the feasibility of efficiency improvement and active surge control and these results were compared with theoretical results

Impact of Channel Estimation Errors on Multiuser Detection via the Replica Method

Directory of Open Access Journals (Sweden)

Li Husheng

2005-01-01

Full Text Available For practical wireless DS-CDMA systems, channel estimation is imperfect due to noise and interference. In this paper, the impact of channel estimation errors on multiuser detection (MUD is analyzed under the framework of the replica method. System performance is obtained in the large system limit for optimal MUD, linear MUD, and turbo MUD, and is validated by numerical results for finite systems.

Thermodynamic Analysis on of Skid-Mounted Coal-bed Methane Liquefaction Device using Cryogenic Turbo-Expander

Science.gov (United States)

Chen, Shuangtao; Niu, Lu; Zeng, Qiang; Li, Xiaojiang; Lou, Fang; Chen, Liang; Hou, Yu

2017-12-01

Coal-bed methane (CBM) reserves are rich in Sinkiang of China, and liquefaction is a critical step for the CBM exploration and utilization. Different from other CBM gas fields in China, CBM distribution in Sinkiang is widespread but scattered, and the pressure, flow-rate and nitrogen content of CBM feed vary significantly. The skid-mounted liquefaction device is suggested as an efficient and economical way to recover methane. Turbo-expander is one of the most important parts which generates the cooling capacity for the cryogenic liquefaction system. Using turbo-expander, more cooling capacity and higher liquefied fraction can be achieved. In this study, skid-mounted CBM liquefaction processes based on Claude cycle are established. Cryogenic turbo-expander with high expansion ratio is employed to improve the efficiency of CBM liquefaction process. The unit power consumption per liquefaction mole flow-rate for CBM feed gas is used as the object function for process optimization, compressor discharge pressure, flow ratio of feed gas to turbo-expander and nitrogen friction are analyzed, and optimum operation range of the liquefaction processes are obtained.

The Case for Distributed Engine Control in Turbo-Shaft Engine Systems

Science.gov (United States)

Culley, Dennis E.; Paluszewski, Paul J.; Storey, William; Smith, Bert J.

2009-01-01

The turbo-shaft engine is an important propulsion system used to power vehicles on land, sea, and in the air. As the power plant for many high performance helicopters, the characteristics of the engine and control are critical to proper vehicle operation as well as being the main determinant to overall vehicle performance. When applied to vertical flight, important distinctions exist in the turbo-shaft engine control system due to the high degree of dynamic coupling between the engine and airframe and the affect on vehicle handling characteristics. In this study, the impact of engine control system architecture is explored relative to engine performance, weight, reliability, safety, and overall cost. Comparison of the impact of architecture on these metrics is investigated as the control system is modified from a legacy centralized structure to a more distributed configuration. A composite strawman system which is typical of turbo-shaft engines in the 1000 to 2000 hp class is described and used for comparison. The overall benefits of these changes to control system architecture are assessed. The availability of supporting technologies to achieve this evolution is also discussed.

Design of Radial Turbo-Expanders for Small Organic Rankine Cycle System

Science.gov (United States)

Arifin, M.; Pasek, A. D.

2015-09-01

This paper discusses the design of radial turbo-expanders for ORC systems. Firstly, the rotor blades were design and the geometry and the perfromance were calculated using several working fluid such as R134a, R143a, R245fa, n-Pentane, and R123. Then, a numerical study was carried out in the fluid flow area with R134a and R123 as the working fluid. Analyses were performed using Computational Fluid Dynamics (CFD) ANSYS CFX on two real gas models, with the k-epsilon and SST (shear stress transport) turbulence models. The results analysis shows the distribution of Mach number, pressure, velocity and temperature along the rotor blade of the radial turbo-expanders and estimation of performance at various operating conditions. CFD analysis show that if the flow area divided into 250,000 grid mesh, and using real gas model SST at steady state condition, 0.4 kg/s of mass flow rate, 15,000 rpm rotor speed, 5 bar inlet pressure, and 373K inlet temperature, the turbo expander produces 6.7 kW, and 5.5 kW of power when using R134a and R123 respectively.

Turbo-extraction of glycosides from Stevia rebaudiana using a fractional factorial design

Directory of Open Access Journals (Sweden)

Paula M. Martins

Full Text Available ABSTRACT Stevia rebaudiana (Bertoni Bertoni, Asteraceae, leaf extract has recently called the attention of food industry as a proposal for natural sweetener. The sweet flavor is attributed to the glycosides, in especial stevioside and rebaudioside A, which are the plant main chemical markers. The aim of the work reported here was to optimize the turbo-extraction of stevia leaves using water, ethanol 70% and 90% (w/w as green solvents. A 25-2 factorial design was applied to study the linear effects of the drug size, solvent to drug ratio, temperature, time and also the turbolysis speed on the extraction of glycosides. The glycosides exhaustive extraction showed that ethanol 70% gave better results and was used for turbo-extraction. The stevioside and rebaudioside A contents were quantified by a validated method by high performance liquid chromatographic with photodiode array detector. The contents of stevioside and rebaudioside A in fluid extract increased with the drug size, but decreased at high shearing speeds and solvent to drug ratio, while their yields decreased at higher temperature and were not affected by turbo speed. An increase in solvent to drug ratio reduced significantly the glycosides percent in dried extract. Optimal solution for S. rebaudiana leaves turbo-extraction was determined by desirability functions. The optimal extraction condition corresponded to drug size of 780 µm, solvent to drug ratio of 10, extraction time of 18 min; temperature of 23 ºC and turbo speed of 20,000 rpm, resulting in yields of 4.98% and 2.70%, for stevioside and rebaudioside A, respectively. These yields are comparable to the ones recently published for dynamic maceration, but with the advantage of shorter extraction times. This work demonstrates that turbolysis is promising for S. rebaudiana glycosides extraction and stimulate new research on the purification of these extracts, which may become an interesting source of income for developing

Functional evaluation of transplanted kidneys by Gd-DTPA enhanced turbo FLASH MR imaging

International Nuclear Information System (INIS)

Nakashima, Rumi; Yamashita, Yasuyuki; Tomiguchi, Seiji; Tsuji, Akinori; Takahashi, Mutsumasa

1996-01-01

We evaluated the usefulness of dynamic turbo FLASH MR imaging in the differential diagnosis of complications after renal transplantation in 17 patients (10 from living relatives and 7 from cadavers). Coronal turbo FLASH dynamic images were obtained every 5 sec for 5 min after an intravenous bolus injection of Gd-DTPA. Corticomedullary differentiation (CMD) on spin echo coronal T 1 -weighted images and MR renogram patterns of the renal cortex and medulla were obtained for quantitative analysis of the Gd-DTPA-enhanced dynamic turbo-FLASH images. The signal intensity ratio of the medulla to cortex after Gd-DTPA enhancement was compared among four groups: normal (n=9), acute tubular necrosis (ATN) or cyclosporine A (CyA) tubulopathy (n=6), acute rejection (AR) in the living related donor kidney (n=4), and AR in the cadaveric kidney (n=5). Although loss of CMD was seen in severe renal dysfunction in the transplanted kidneys, there was considerable overlap among the four groups. On dynamic study, there was significant differences in the signal intensity ratio of the medulla to cortex between normally functioning kidneys or ATN/CyA tubulopathy and AR (p<0.01). In patients with severe renal dysfunction, the arterial cortical peak was indistinct. In conclusion, MR renograms obtained from dynamic turbo FLASH MR imaging played a significant role in evaluating dysfunction of the renal transplant. (author)

Design of deterministic interleaver for turbo codes

International Nuclear Information System (INIS)

Arif, M.A.; Sheikh, N.M.; Sheikh, A.U.H.

2008-01-01

The choice of suitable interleaver for turbo codes can improve the performance considerably. For long block lengths, random interleavers perform well, but for some applications it is desirable to keep the block length shorter to avoid latency. For such applications deterministic interleavers perform better. The performance and design of a deterministic interleaver for short frame turbo codes is considered in this paper. The main characteristic of this class of deterministic interleaver is that their algebraic design selects the best permutation generator such that the points in smaller subsets of the interleaved output are uniformly spread over the entire range of the information data frame. It is observed that the interleaver designed in this manner improves the minimum distance or reduces the multiplicity of first few spectral lines of minimum distance spectrum. Finally we introduce a circular shift in the permutation function to reduce the correlation between the parity bits corresponding to the original and interleaved data frames to improve the decoding capability of MAP (Maximum A Posteriori) probability decoder. Our solution to design a deterministic interleaver outperforms the semi-random interleavers and the deterministic interleavers reported in the literature. (author)

Aeroderivative Gas Turbo engine in CHP Plant. Compatibility Problems

Directory of Open Access Journals (Sweden)

Sorinel-Gicu TALIF

2010-12-01

Full Text Available The paper presents the possibilities to develop Combined Cycle Units based onaeroderivative Gas Turbo engines and on existing Steam Turbines. The specific compatibilityproblems of these components and the thermodynamic performances of the analyzed Combined CycleUnits are also presented.

Fault diagnostics for turbo-shaft engine sensors based on a simplified on-board model.

Science.gov (United States)

Lu, Feng; Huang, Jinquan; Xing, Yaodong

2012-01-01

Combining a simplified on-board turbo-shaft model with sensor fault diagnostic logic, a model-based sensor fault diagnosis method is proposed. The existing fault diagnosis method for turbo-shaft engine key sensors is mainly based on a double redundancies technique, and this can't be satisfied in some occasions as lack of judgment. The simplified on-board model provides the analytical third channel against which the dual channel measurements are compared, while the hardware redundancy will increase the structure complexity and weight. The simplified turbo-shaft model contains the gas generator model and the power turbine model with loads, this is built up via dynamic parameters method. Sensor fault detection, diagnosis (FDD) logic is designed, and two types of sensor failures, such as the step faults and the drift faults, are simulated. When the discrepancy among the triplex channels exceeds a tolerance level, the fault diagnosis logic determines the cause of the difference. Through this approach, the sensor fault diagnosis system achieves the objectives of anomaly detection, sensor fault diagnosis and redundancy recovery. Finally, experiments on this method are carried out on a turbo-shaft engine, and two types of faults under different channel combinations are presented. The experimental results show that the proposed method for sensor fault diagnostics is efficient.

Fault Diagnostics for Turbo-Shaft Engine Sensors Based on a Simplified On-Board Model

Directory of Open Access Journals (Sweden)

Yaodong Xing

2012-08-01

Full Text Available Combining a simplified on-board turbo-shaft model with sensor fault diagnostic logic, a model-based sensor fault diagnosis method is proposed. The existing fault diagnosis method for turbo-shaft engine key sensors is mainly based on a double redundancies technique, and this can’t be satisfied in some occasions as lack of judgment. The simplified on-board model provides the analytical third channel against which the dual channel measurements are compared, while the hardware redundancy will increase the structure complexity and weight. The simplified turbo-shaft model contains the gas generator model and the power turbine model with loads, this is built up via dynamic parameters method. Sensor fault detection, diagnosis (FDD logic is designed, and two types of sensor failures, such as the step faults and the drift faults, are simulated. When the discrepancy among the triplex channels exceeds a tolerance level, the fault diagnosis logic determines the cause of the difference. Through this approach, the sensor fault diagnosis system achieves the objectives of anomaly detection, sensor fault diagnosis and redundancy recovery. Finally, experiments on this method are carried out on a turbo-shaft engine, and two types of faults under different channel combinations are presented. The experimental results show that the proposed method for sensor fault diagnostics is efficient.

VLSI Architectures for Sliding-Window-Based Space-Time Turbo Trellis Code Decoders

Directory of Open Access Journals (Sweden)

Georgios Passas

2012-01-01

Full Text Available The VLSI implementation of SISO-MAP decoders used for traditional iterative turbo coding has been investigated in the literature. In this paper, a complete architectural model of a space-time turbo code receiver that includes elementary decoders is presented. These architectures are based on newly proposed building blocks such as a recursive add-compare-select-offset (ACSO unit, A-, B-, Γ-, and LLR output calculation modules. Measurements of complexity and decoding delay of several sliding-window-technique-based MAP decoder architectures and a proposed parameter set lead to defining equations and comparison between those architectures.

A sealed turbo-alternator using any working-fluid

International Nuclear Information System (INIS)

Chollet, Maurice.

1973-01-01

The invention relates to a sealed turbo-alternator operating with a working fluid other than water. The turbo-alternator and the feed and lubricating pumps thereof are housed in a sealed casing. The latter constitutes, with the heat pump and the heat sink, a sealed enclosure containing the working and lubricating fluid. The alternator, which comprises neither collector nor brushes, is dipped in the working fluid vapor. Electric energy leaves the sealed enclosure through insulating sealed passager. In view of the absence of leakage it is possible to select (e.g. among freons) a working fluid well suited to the temperature differential between the heat source and the heat sink, and, accordingly to use temperature drops which could be too small in the case of steam. The various applications are as follows: recovery of calories at the exhaust of diesels and of gas turbines or in the cooling water of diesels; equipment of isotopic generators; recovery of calories from factory waste thrown into rivers (anti-pollution effect in view of the lowering of water temperature); non-polluting engine for special electrical vehicles [fr

The reproductive cycle of the intertidal gastropod Turbo coronatus ...

African Journals Online (AJOL)

Histological methods were used to determine the reproductive cycle of Turbo coronatus. Ovarian development was assessed from the relative proportions of mature and immature oocytes in sectioned material. Testicular tissues ware subjectively given a maturity index based on the relative proportions of the various ...

Ultrashort turbo spinecho versus turbo spinecho in the evaluation of musculoskeletal diseases

International Nuclear Information System (INIS)

Breitenseher, M.; Kontaxis, G.; Fleischmann, D.; Rand, T.H.; Imhof, H.; Trattnig, S.

1995-01-01

Ultrashort turbo spin-echo sequence (TSE) has the advantage of shorter scan times, minimizing motion artifacts, but has the disadvantage of a lower signal-to-noise ratio and suffers from different artifacts. T2-weighted ultrashort TSE (echo train 24) and TSE (echo train 11) were compared in degenerative lesions of the spine (n=9) and ligamentous lesions associated with sprained ankle injuries (n=5). The imaging quality of ultrashort TSE was very similar to TSE. There was no difference in diagnostic reliability with ultrashort TSE compared to TSE in the spine or ankle. With regard to contrast properties a higher signal intensity of fatty bone marrow was obtained with ultrashort TSE, with consecutive lower contrast between fluid and edema on the one hand and fatty tissue on the other. (orig.) [de

Fast parallel-series analog-to-digital converter

International Nuclear Information System (INIS)

Pogosov, A.Yu.

1987-01-01

Fast analog-to-digital converters are used in systems for detection of rapid processes, nuclear spectroscopy. A 12-digit analog-to-digital converter with conversion time of 160 ns and conversion frequency of 8.3 MHz is described; a segmented digital-to-analog converter with differential non-linearity of < 0.01% and a differential amplifier-limiter with setting time of 80 ns at the error of 0.2% are utilized in the converter; a control device is based on the chain of flip-flop circuit

An emergent approach to analogical inference

Science.gov (United States)

Thibodeau, Paul H.; Flusberg, Stephen J.; Glick, Jeremy J.; Sternberg, Daniel A.

2013-03-01

In recent years, a growing number of researchers have proposed that analogy is a core component of human cognition. According to the dominant theoretical viewpoint, analogical reasoning requires a specific suite of cognitive machinery, including explicitly coded symbolic representations and a mapping or binding mechanism that operates over these representations. Here we offer an alternative approach: we find that analogical inference can emerge naturally and spontaneously from a relatively simple, error-driven learning mechanism without the need to posit any additional analogy-specific machinery. The results also parallel findings from the developmental literature on analogy, demonstrating a shift from an initial reliance on surface feature similarity to the use of relational similarity later in training. Variants of the model allow us to consider and rule out alternative accounts of its performance. We conclude by discussing how these findings can potentially refine our understanding of the processes that are required to perform analogical inference.

Evaluation of endometrial carcinoma by multislice dynamic MR imaging with Turbo FLASH

Energy Technology Data Exchange (ETDEWEB)

Asakawa, Mari [Okayama Univ. (Japan). School of Medicine

1995-04-01

The purpose of this study was to investigate the usefulness of multislice dynamic MR imaging with Turbo FLASH in assessing myometrial invasion by endometrial carcinoma. Dynamic MR imaging was performed with bolus injection of Gd-DTPA and with 1.5-T Siemens Magnetom imager using Turbo FLASH. Thirty-six endometrial carcinomas were evaluated with pathologic correlation. Junctional zone showed more rapid contrast enhancement effects than myometrium even after menopause. Contrast to noise ratio between junctional zone and endometrial carcinoma was the highest about fifty seconds after bolus injection. Only at that time could the degree of invasion to junctional zone in post-menopausal women whose junctional zones could not be seen on T{sub 2}-weighted images or contrast-enhanced T{sub 1}-weighted images be evaluated correctly. The accuracy in assessing myometrial invasion with T{sub 2}-weighted images, postcontrast T{sub 1}-weighted images, and dynamic MR imaging was 75%, 81% and 89% respectively. Though there was no statistically significant difference, multislice dynamic imaging with Turbo FLASH technique is considered to be a useful imaging method for the pre-operative assessment of myometrial invasion by endometrial carcinoma. (author).

Torsional vibration analysis in turbo-generator shaft due to mal-synchronization fault

Science.gov (United States)

Bangunde, Abhishek; Kumar, Tarun; Kumar, Rajeev; Jain, S. C.

2018-03-01

A rotor of turbo-generator shafting is many times subjected to torsional vibrations during its lifespan. The reasons behind these vibrations are three-Phase fault, two-phase fault, line to ground fault, faulty-mal synchronization etc. Sometimes these vibrations can cause complete failure of turbo-generator shafting system. To calculate moment variation during these faults on the shafting system vibration analysis is done using Finite Elements Methods to calculate mass and stiffness matrix. The electrical disturbance caused during Mal-synchronization is put on generator section, and corresponding second order equations are solved by using “Duhamel Integral”. From the moment variation plots at four sections critically loaded sections are identified.

Turbo-Gallager Codes: The Emergence of an Intelligent Coding ...

African Journals Online (AJOL)

Today, both turbo codes and low-density parity-check codes are largely superior to other code families and are being used in an increasing number of modern communication systems including 3G standards, satellite and deep space communications. However, the two codes have certain distinctive characteristics that ...

Thermal characteristics of high-temperature R718 heat pumps with turbo compressor thermal vapor recompression

International Nuclear Information System (INIS)

Šarevski, Milan N.; Šarevski, Vasko N.

2017-01-01

Highlights: • High pressure ratio, high speed, transonic R718 centrifugal compressors. • High efficient industrial evaporators/concentrators with turbo thermal vapor recompression. • Utilization of waste heat from industrial thermal and processing systems. • R718 is an ideal refrigerant for the novel high-temperature industrial heat pumps. • Application of single-stage R718 centrifugal compressors. - Abstract: Characteristics of R718 centrifugal compressors are analyzed and range of their applications in industrial high-temperature heat pumps, district heating systems and geothermal green house heating systems are estimated. Implementation of turbo compressor thermal vapor recompression in industrial evaporating/concentrating plants for waste heat utilization results in a high energy efficiency and in other technical, economical and environmental benefits. A novel concept of turbo compression R718 heat pumps is proposed and an assessment of their thermal characteristics is presented for utilization of waste heat from industrial thermal plants and systems (boilers, furnaces, various technological and metallurgical cooling processes, etc.), and for applications in district heating and geothermal green house heating systems. R718 is an ideal refrigerant for the novel high-temperature turbo compression industrial heat pumps. Direct evaporation and condensation are advantages of the proposed system which lead to higher COP, and to simplification of the plant and lower cost.

Turbo Equalization Using Partial Gaussian Approximation

DEFF Research Database (Denmark)

Zhang, Chuanzong; Wang, Zhongyong; Manchón, Carles Navarro

2016-01-01

This letter deals with turbo equalization for coded data transmission over intersymbol interference (ISI) channels. We propose a message-passing algorithm that uses the expectation propagation rule to convert messages passed from the demodulator and decoder to the equalizer and computes messages...... returned by the equalizer by using a partial Gaussian approximation (PGA). We exploit the specific structure of the ISI channel model to compute the latter messages from the beliefs obtained using a Kalman smoother/equalizer. Doing so leads to a significant complexity reduction compared to the initial PGA...

Iterative Signal Processing for Mitigation of Analog-to-Digital Converter Clipping Distortion in Multiband OFDMA Receivers

Directory of Open Access Journals (Sweden)

Markus Allén

2012-01-01

Full Text Available In modern wideband communication receivers, the large input-signal dynamics is a fundamental problem. Unintentional signal clipping occurs, if the receiver front-end with the analog-to-digital interface cannot respond to rapidly varying conditions. This paper discusses digital postprocessing compensation of such unintentional clipping in multiband OFDMA receivers. The proposed method iteratively mitigates the clipping distortion by exploiting the symbol decisions. The performance of the proposed method is illustrated with various computer simulations and also verified by concrete laboratory measurements with commercially available analog-to-digital hardware. It is shown that the clipping compensation algorithm implemented in a turbo decoding OFDM receiver is able to remove almost all the clipping distortion even under significant clipping in fading channel circumstances. That is to say, it is possible to nearly recover the receiver performance to the level, which would be achieved in the equivalent nonclipped situation.

The matching of characteristics of the turbo-supercharging system and two-stroke transport diesel engine

OpenAIRE

Алёхин, Сергей Алексеевич; Герасименко, Владимир Петрович; Опалев, Василий Анатольевич

2013-01-01

The basic problems of the matching of characteristics of turbo-supercharging units and two-stroke transport diesel engines with various number of cylinders are considered. Influence of the number of impeller tiers and other geometrical parameters on the pressure characteristic of the centrifugal compressor and joint action of the compressor and the piston engine is investigated. Effective measures on the optimum coordination of a mechanical turbo-supercharging with a transport diesel engin...

A neurocomputational model of analogical reasoning and its breakdown in frontotemporal lobar degeneration.

Science.gov (United States)

Morrison, Robert G; Krawczyk, Daniel C; Holyoak, Keith J; Hummel, John E; Chow, Tiffany W; Miller, Bruce L; Knowlton, Barbara J

2004-03-01

Analogy is important for learning and discovery and is considered a core component of intelligence. We present a computational account of analogical reasoning that is compatible with data we have collected from patients with cortical degeneration of either their frontal or anterior temporal cortices due to frontotemporal lobar degeneration (FTLD). These two patient groups showed different deficits in picture and verbal analogies: frontal lobe FTLD patients tended to make errors due to impairments in working memory and inhibitory abilities, whereas temporal lobe FTLD patients tended to make errors due to semantic memory loss. Using the "Learning and Inference with Schemas and Analogies" model, we provide a specific account of how such deficits may arise within neural networks supporting analogical problem solving.

Research on Development of Turbo-generator with Partial Admission Nozzle for Supercritical CO{sub 2} Power Generation

Energy Technology Data Exchange (ETDEWEB)

Cho, Junhyun; Shin, Hyung-ki; Lee, Gilbong; Baik, Young-Jin [Korea Institute of Energy Research (KIER), Daejeon (Korea, Republic of); Kang, Young-Seok [Korea Aerospace Research Institute (KARI), Daejeon (Korea, Republic of); Kim, Byunghui [InGineers Ltd., Seoul (Korea, Republic of)

2017-04-15

A Sub-kWe small-scale experimental test loop was manufactured to investigate characteristics of the supercritical carbon dioxide power cycle. A high-speed turbo-generator was also designed and manufactured. The designed rotational speed of this turbo-generator was 200,000 rpm. Because of the low expansion ratio through the turbine and low mass flowrate, the rotational speed of the turbo-generator was high. Therefore, it was difficult to select the rotating parts and design the turbine wheel, axial force balance and rotor dynamics in the lab-scale experimental test loop. Using only one channel of the nozzle, the partial admission method was adapted to reduce the rotational speed of the rotor. This was the world’s first approach to the supercritical carbon dioxide turbo-generator. A cold-run test using nitrogen gas under an atmospheric condition was conducted to observe the effect of the partial admission nozzle on the rotor dynamics. The vibration level of the rotor was obtained using a gap sensor, and the results showed that the effect of the partial admission nozzle on the rotor dynamics was allowable.

SHEAN (Simplified Human Error Analysis code) and automated THERP

International Nuclear Information System (INIS)

Wilson, J.R.

1993-01-01

One of the most widely used human error analysis tools is THERP (Technique for Human Error Rate Prediction). Unfortunately, this tool has disadvantages. The Nuclear Regulatory Commission, realizing these drawbacks, commissioned Dr. Swain, the author of THERP, to create a simpler, more consistent tool for deriving human error rates. That effort produced the Accident Sequence Evaluation Program Human Reliability Analysis Procedure (ASEP), which is more conservative than THERP, but a valuable screening tool. ASEP involves answering simple questions about the scenario in question, and then looking up the appropriate human error rate in the indicated table (THERP also uses look-up tables, but four times as many). The advantages of ASEP are that human factors expertise is not required, and the training to use the method is minimal. Although not originally envisioned by Dr. Swain, the ASEP approach actually begs to be computerized. That WINCO did, calling the code SHEAN, for Simplified Human Error ANalysis. The code was done in TURBO Basic for IBM or IBM-compatible MS-DOS, for fast execution. WINCO is now in the process of comparing this code against THERP for various scenarios. This report provides a discussion of SHEAN

Condition monitoring of steam turbo generators of captive power plant at HWP (Manuguru) through vibration analysis

International Nuclear Information System (INIS)

Krishnareddy, G.; Chandramouli, M.; Gupta, R.V.

2002-01-01

Turbo Generator is a critical equipment in steam based power plant circuit. Any failure causes loss of production and hence as applicable to Heavy Water Plant, Manuguru, it results in loss of heavy water production as the captive power plant at Manuguru is solely designed to supply steam and power to Main Plant, which is meant for production of heavy water. Thereby condition monitoring is very much essential and required as part of predictive maintenance program for the turbo generators which are in continuous operation. This paper focuses on identification of the turbo generator system through vibration spectrum, characterising and differentiating the fault mechanisms, trending the faults through changes in vibration spectrums and orbit plots and subsequently planning for corrective actions/measures after evaluating the changes in machine conditions

Young Children's Analogical Reasoning across Cultures: Similarities and Differences

Science.gov (United States)

Richland, Lindsey Engle; Chan, Tsz-Kit; Morrison, Robert G.; Au, Terry Kit-Fong

2010-01-01

A cross-cultural comparison between U.S. and Hong Kong preschoolers examined factors responsible for young children's analogical reasoning errors. On a scene analogy task, both groups had adequate prerequisite knowledge of the key relations, were the same age, and showed similar baseline performance, yet Chinese children outperformed U.S. children…

Dynamic configuration management of a multi-standard and multi-mode reconfigurable multi-ASIP architecture for turbo decoding

Science.gov (United States)

Lapotre, Vianney; Gogniat, Guy; Baghdadi, Amer; Diguet, Jean-Philippe

2017-12-01

The multiplication of connected devices goes along with a large variety of applications and traffic types needing diverse requirements. Accompanying this connectivity evolution, the last years have seen considerable evolutions of wireless communication standards in the domain of mobile telephone networks, local/wide wireless area networks, and Digital Video Broadcasting (DVB). In this context, intensive research has been conducted to provide flexible turbo decoder targeting high throughput, multi-mode, multi-standard, and power consumption efficiency. However, flexible turbo decoder implementations have not often considered dynamic reconfiguration issues in this context that requires high speed configuration switching. Starting from this assessment, this paper proposes the first solution that allows frame-by-frame run-time configuration management of a multi-processor turbo decoder without compromising the decoding performances.

MR colonography with fecal tagging: comparison between 2D turbo FLASH and 3D FLASH sequences

International Nuclear Information System (INIS)

Papanikolaou, Nickolas; Grammatikakis, John; Maris, Thomas; Prassopoulos, Panos; Gourtsoyiannis, Nicholas; Lauenstein, Thomas

2003-01-01

The objective of this study was to compare inversion recovery turbo 2D fast low-angle shot (FLASH) and 3D FLASH sequences for fecal-tagged MR colonography studies. Fifteen consecutive patients with indications for colonoscopy underwent MR colonography with fecal tagging. An inversion recovery turbo-FLASH sequence was applied and compared in terms of artifacts presence, efficiency for masking residual stool, and colonic wall conspicuity with a fat-saturated 3D FLASH sequence. Both sequences were acquired following administration of paramagnetic contrast agent. Contrast-to-noise ratio and relative contrast between colonic wall and lumen were calculated and compared for both sequences. Turbo 2D FLASH provided fewer artifacts, higher efficiency for masking the residual stool, and colonic wall conspicuity equivalent to 3D FLASH. An inversion time of 10 ms provided homogeneously low signal intensity of the colonic lumen. Contrast to noise between colonic wall and lumen was significantly higher in the 3D FLASH images, whereas differences in relative contrast were not statistically significant. An optimized inversion-recovery 2D turbo-FLASH sequence provides better fecal tagging results and should be added to the 3D FLASH sequence when designing dark-lumen MR colonography examination protocols. (orig.)

Experimental Study in a Cascade Row for Improving the Performance of a Partially Admitted Turbo-Expander

Directory of Open Access Journals (Sweden)

Soo-Yong Cho

2015-12-01

Full Text Available Turbo-expanders are widely used as power generators in the field of energy conversion such as organic Rankine cycle (ORC systems. When the available thermal energy is not sufficient to operate the turbo-expander in full admission, it is much better to operate in partial admission instead of stand-down. However, the performance of the turbo-expander greatly depends on the operating conditions. Among many operating conditions, the flow angle at the nozzle and solidity can be major factors affecting the performance of the expander. In order to investigate the optimal operation conditions, experiments were conducted in a linear cascade apparatus simulating the operation of turbo-expander in partial admission. Three different nozzle flow angles of 58°, 65°, and 72° were adopted, and the experiments were conducted with respective solidities of 1.25, 1.38, and 1.67 at each nozzle flow angle. The cross section of the nozzle was rectangular and the chord of the tested blade was 200 mm. The blades moved in a rotational direction, and the forces on the blades were measured with the surface pressure at steady state. The experimental results showed that the rotational force increased for a larger solidity or for a smaller nozzle flow angle.

Design and Implementation of Adaptive Turbo Encoder for Quantized Software Defined Low-Power DVB-RCS Radios

Directory of Open Access Journals (Sweden)

S. H. Elramly

2010-11-01

Full Text Available Turbo codes are employed in every robust wireless digital communications system. Those codes have been adopted for the satellite return channel in DVB-RCS (Return Channel via Satellite standard. In Software Defined Radios (SDRs, Field Programmable Gate Array technology (FPGA is considered a highly configurable option for implementing many sophisticated signal processing tasks. The implementation for such codes is complex and dissipates a large amount of power. This paper studies the efficient implementation of quantized DVB-RCS turbo coding. Also, a low-power, turbo encoder for DVB-RCS is described using a VHDL code. The proposed encoder design is implemented on Xilinx Virtex-II Pro, XC2vpx30 FPGA chip. FPGA Advantage Pro package provided by Mentor Graphics is used for VHDL description and ISE 10.1 by Xilinx is used for synthetization.

Culture and error in space: implications from analog environments.

Science.gov (United States)

Helmreich, R L

2000-09-01

An ongoing study investigating national, organizational, and professional cultures in aviation and medicine is described. Survey data from 26 nations on 5 continents show highly significant national differences regarding appropriate relationships between leaders and followers, in group vs. individual orientation, and in values regarding adherence to rules and procedures. These findings replicate earlier research on dimensions of national culture. Data collected also isolate significant operational issues in multi-national flight crews. While there are no better or worse cultures, these cultural differences have operational implications for the way crews function in an international space environment. The positive professional cultures of pilots and physicians exhibit a high enjoyment of the job and professional pride. However, a negative component was also identified characterized by a sense of personal invulnerability regarding the effects of stress and fatigue on performance. This misperception of personal invulnerability has operational implications such as failures in teamwork and increased probability of error. A second component of the research examines team error in operational environments. From observational data collected during normal flight operations, new models of threat and error and their management were developed that can be generalized to operations in space and other socio-technological domains. Five categories of crew error are defined and their relationship to training programs in team performance, known generically as Crew Resource Management, is described. The relevance of these data for future spaceflight is discussed.

SimCommSys: taking the errors out of error-correcting code simulations

Directory of Open Access Journals (Sweden)

Johann A. Briffa

2014-06-01

Full Text Available In this study, we present SimCommSys, a simulator of communication systems that we are releasing under an open source license. The core of the project is a set of C + + libraries defining communication system components and a distributed Monte Carlo simulator. Of principal interest is the error-control coding component, where various kinds of binary and non-binary codes are implemented, including turbo, LDPC, repeat-accumulate and Reed–Solomon. The project also contains a number of ready-to-build binaries implementing various stages of the communication system (such as the encoder and decoder, a complete simulator and a system benchmark. Finally, SimCommSys also provides a number of shell and python scripts to encapsulate routine use cases. As long as the required components are already available in SimCommSys, the user may simulate complete communication systems of their own design without any additional programming. The strict separation of development (needed only to implement new components and use (to simulate specific constructions encourages reproducibility of experimental work and reduces the likelihood of error. Following an overview of the framework, we provide some examples of how to use the framework, including the implementation of a simple codec, the specification of communication systems and their simulation.

Measurement and control system for cryogenic helium gas bearing turbo-expander experimental platform based on Siemens PLC S7-300

Energy Technology Data Exchange (ETDEWEB)

Li, J.; Xiong, L. Y.; Peng, N.; Dong, B.; Liu, L. Q. [Key Laboratory of Cryogenics, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing, 100190 (China); Wang, P. [Beijing Sciample Technology Co., Ltd., Beijing, 100190 (China)

2014-01-29

An experimental platform for cryogenic Helium gas bearing turbo-expanders is established at the Technical Institute of Physics and Chemistry, Chinese Academy of Sciences. This turbo-expander experimental platform is designed for performance testing and experimental research on Helium turbo-expanders with different sizes from the liquid hydrogen temperature to the room temperature region. A measurement and control system based on Siemens PLC S7-300 for this turbo-expander experimental platform is developed. Proper sensors are selected to measure such parameters as temperature, pressure, rotation speed and air flow rate. All the collected data to be processed are transformed and transmitted to S7-300 CPU. Siemens S7-300 series PLC CPU315-2PN/DP is as master station and two sets of ET200M DP remote expand I/O is as slave station. Profibus-DP field communication is established between master station and slave stations. The upper computer Human Machine Interface (HMI) is compiled using Siemens configuration software WinCC V6.2. The upper computer communicates with PLC by means of industrial Ethernet. Centralized monitoring and distributed control is achieved. Experimental results show that this measurement and control system has fulfilled the test requirement for the turbo-expander experimental platform.

Measurement and control system for cryogenic helium gas bearing turbo-expander experimental platform based on Siemens PLC S7-300

Science.gov (United States)

Li, J.; Xiong, L. Y.; Peng, N.; Dong, B.; Wang, P.; Liu, L. Q.

2014-01-01

An experimental platform for cryogenic Helium gas bearing turbo-expanders is established at the Technical Institute of Physics and Chemistry, Chinese Academy of Sciences. This turbo-expander experimental platform is designed for performance testing and experimental research on Helium turbo-expanders with different sizes from the liquid hydrogen temperature to the room temperature region. A measurement and control system based on Siemens PLC S7-300 for this turbo-expander experimental platform is developed. Proper sensors are selected to measure such parameters as temperature, pressure, rotation speed and air flow rate. All the collected data to be processed are transformed and transmitted to S7-300 CPU. Siemens S7-300 series PLC CPU315-2PN/DP is as master station and two sets of ET200M DP remote expand I/O is as slave station. Profibus-DP field communication is established between master station and slave stations. The upper computer Human Machine Interface (HMI) is compiled using Siemens configuration software WinCC V6.2. The upper computer communicates with PLC by means of industrial Ethernet. Centralized monitoring and distributed control is achieved. Experimental results show that this measurement and control system has fulfilled the test requirement for the turbo-expander experimental platform.

Analogy in systems management: a theoretical inquiry

Energy Technology Data Exchange (ETDEWEB)

Silverman, B.G.

1983-11-01

This theoretical analysis of the intuitive and diffuse characteristics of analogical reasoning processes is the first step in a research effort intended to lead to: understanding of common (and possibly costly) errors, pitfalls, travails, and problem-solving impediments; possible recommendations for improvements to organizational structures, control and coordination processes, and management information flows, and guidelines for a generalized analogical reasoning support framework (e.g., a handbook, a knowledge bank design, and/or even a software package/artificial intelligence program). 233 references.

Reliability of analog quantum simulation

Energy Technology Data Exchange (ETDEWEB)

Sarovar, Mohan [Sandia National Laboratories, Digital and Quantum Information Systems, Livermore, CA (United States); Zhang, Jun; Zeng, Lishan [Shanghai Jiao Tong University, Joint Institute of UMich-SJTU, Key Laboratory of System Control and Information Processing (MOE), Shanghai (China)

2017-12-15

Analog quantum simulators (AQS) will likely be the first nontrivial application of quantum technology for predictive simulation. However, there remain questions regarding the degree of confidence that can be placed in the results of AQS since they do not naturally incorporate error correction. Specifically, how do we know whether an analog simulation of a quantum model will produce predictions that agree with the ideal model in the presence of inevitable imperfections? At the same time there is a widely held expectation that certain quantum simulation questions will be robust to errors and perturbations in the underlying hardware. Resolving these two points of view is a critical step in making the most of this promising technology. In this work we formalize the notion of AQS reliability by determining sensitivity of AQS outputs to underlying parameters, and formulate conditions for robust simulation. Our approach naturally reveals the importance of model symmetries in dictating the robust properties. To demonstrate the approach, we characterize the robust features of a variety of quantum many-body models. (orig.)

A Lagrangian parcel based mixing plane method for calculating water based mixed phase particle flows in turbo-machinery

Science.gov (United States)

Bidwell, Colin S.

2015-05-01

A method for calculating particle transport through turbo-machinery using the mixing plane analogy was developed and used to analyze the energy efficient engine . This method allows the prediction of temperature and phase change of water based particles along their path and the impingement efficiency and particle impact property data on various components in the engine. This methodology was incorporated into the LEWICE3D V3.5 software. The method was used to predict particle transport in the low pressure compressor of the . The was developed by NASA and GE in the early 1980s as a technology demonstrator and is representative of a modern high bypass turbofan engine. The flow field was calculated using the NASA Glenn ADPAC turbo-machinery flow solver. Computations were performed for a Mach 0.8 cruise condition at 11,887 m assuming a standard warm day for ice particle sizes of 5, 20 and 100 microns and a free stream particle concentration of . The impingement efficiency results showed that as particle size increased average impingement efficiencies and scoop factors increased for the various components. The particle analysis also showed that the amount of mass entering the inner core decreased with increased particle size because the larger particles were less able to negotiate the turn into the inner core due to particle inertia. The particle phase change analysis results showed that the larger particles warmed less as they were transported through the low pressure compressor. Only the smallest 5 micron particles were warmed enough to produce melting with a maximum average melting fraction of 0.18. The results also showed an appreciable amount of particle sublimation and evaporation for the 5 micron particles entering the engine core (22.6 %).

Preprocessor that Enables the Use of GridProTM Grids for Unsteady Reynolds-Averaged Navier-Stokes Code TURBO

Science.gov (United States)

Shyam, Vikram

2010-01-01

A preprocessor for the Computational Fluid Dynamics (CFD) code TURBO has been developed and tested. The preprocessor converts grids produced by GridPro (Program Development Company (PDC)) into a format readable by TURBO and generates the necessary input files associated with the grid. The preprocessor also generates information that enables the user to decide how to allocate the computational load in a multiple block per processor scenario.

The LHCb Turbo stream

CERN Document Server

AUTHOR|(CDS)2070171

2016-01-01

The LHCb experiment will record an unprecedented dataset of beauty and charm hadron decays during Run II of the LHC, set to take place between 2015 and 2018. A key computing challenge is to store and process this data, which limits the maximum output rate of the LHCb trigger. So far, LHCb has written out a few kHz of events containing the full raw sub-detector data, which are passed through a full offline event reconstruction before being considered for physics analysis. Charm physics in particular is limited by trigger output rate constraints. A new streaming strategy includes the possibility to perform the physics analysis with candidates reconstructed in the trigger, thus bypassing the offline reconstruction. In the Turbo stream the trigger will write out a compact summary of physics objects containing all information necessary for analyses. This will allow an increased output rate and thus higher average efficiencies and smaller selection biases. This idea will be commissioned and developed during 2015 wi...

The Effect of Crude Extract of Turbo coronatus from the Persian Gulf on Serum Biochemical Parameters and Hematiological Parameters of Rats

Directory of Open Access Journals (Sweden)

Amir Vazirizadeh

2017-05-01

Full Text Available : Turbotoxins are marine secondary metabolites that produce in Turbinidae family and were isolated from Japanese Turbo marmorata for the first time. A few research has been done on these metabolites so far. Another species, Turbo coronatus exists in Iran. The main aim of the current project was to investigate some biological effects of the crude extract of Turbo coronatus from the Persian Gulf . Materials and methods: In this study, 18 rats were selected in three groups including the control group. The experimental groups received ½ and 1/3 lethal doses intravenously and serum levels of liver and muscle enzymes, electrolytes and complete blood counts (CBC were measured after 24 hours. : The levels of liver and muscle enzymes, amylase, sodium, potassium, calcium, phosphorus, ferrous, haptoglobin, albumin and creatinine were significantly increased in experimental group compared with the control group by injection of crude extract of Turbo coronatus; however, hemoglobin, mean corpuscular volume (MCV, red blood cell count, magnesium, and glucose levels were significantly decreased in the experimental group compared with the control group. : Intravenous injection of ½ and 1/3 lethal doses of the crude extract of Turbo coronatus to rats produced rhabdomyolysis and hepatocytes injury. In addition, the crude extract injection acted as a haematoxin and decreased hemoglobin and MCV.

Volterra Filtering for ADC Error Correction

Directory of Open Access Journals (Sweden)

J. Saliga

2001-09-01

Full Text Available Dynamic non-linearity of analog-to-digital converters (ADCcontributes significantly to the distortion of digitized signals. Thispaper introduces a new effective method for compensation such adistortion based on application of Volterra filtering. Considering ana-priori error model of ADC allows finding an efficient inverseVolterra model for error correction. Efficiency of proposed method isdemonstrated on experimental results.

Detection of brain metastasis. Comparison of Turbo-FLAIR imaging, T2-weighted imaging and double-dose gadolinium-enhanced MR imaging

International Nuclear Information System (INIS)

Okubo, Toshiyuki; Hayashi, Naoto; Shirouzu, Ichiro; Abe, Osamu; Ohtomo, Kuni; Sasaki, Yasuhito; Aoki, Shigeki; Wada, Akihiko

1998-01-01

The purpose of this study was to compare Turbo-FLAIR imaging, T 2 -weighted imaging, and double-dose gadolinium-enhanced MR imaging in the detection of brain metastasis. Using the three sequences, 20 consecutive patients with brain metastases were prospectively studied with a 1.5-Tesla system. Three independent, blinded readers assessed the images for the presence, size, number, and location of metastatic lesions. In the detection of large lesions (>0.5 cm), Turbo-FLAIR imaging (38/48, 79%) was not significantly different from gadolinium-enhanced imaging (42/48, 88%) (p=0.273). T 2 -weighted imaging (31/48, 65%), however, was inferior to gadolinium-enhanced imaging (p<0.05). There was no difference between Turbo-FLAIR imaging and gadolinium-enhanced imaging in the accuracy of detecting solitary brain metastasis (4/4, 100%). In conclusion, Turbo-FLAIR imaging is a useful, noninvasive screening modality for brain metastasis. Its use may lead to cost savings in the diagnosis of brain metastases and may impact positively the cost-effectiveness of treatment. (author)

Analogical study of the servo-control of a reactivity modulator

International Nuclear Information System (INIS)

Le Bot, Michel

1969-03-01

In the context of the study of the transfer functions related to the Cabri reactor, this paper presents: the objective of the servo-control (reactivity modulator, reasons for the analogical study), the principles of the servo-control (description of the servo-controlled system, elaboration of the error signal, principles of the phase meter, critical analysis of different types of phase meters), the analogical formulation (transfer diagram of the process, analogical simulation of the process, analogical realization of the phase meter, simulation of the Low Frequency generator), study of the controlled system and results (system responses to echelon and ramp signals, responses of the controlled system with the phase meter in feedback)

On the impact of approximate computation in an analog DeSTIN architecture.

Science.gov (United States)

Young, Steven; Lu, Junjie; Holleman, Jeremy; Arel, Itamar

2014-05-01

Deep machine learning (DML) holds the potential to revolutionize machine learning by automating rich feature extraction, which has become the primary bottleneck of human engineering in pattern recognition systems. However, the heavy computational burden renders DML systems implemented on conventional digital processors impractical for large-scale problems. The highly parallel computations required to implement large-scale deep learning systems are well suited to custom hardware. Analog computation has demonstrated power efficiency advantages of multiple orders of magnitude relative to digital systems while performing nonideal computations. In this paper, we investigate typical error sources introduced by analog computational elements and their impact on system-level performance in DeSTIN--a compositional deep learning architecture. These inaccuracies are evaluated on a pattern classification benchmark, clearly demonstrating the robustness of the underlying algorithm to the errors introduced by analog computational elements. A clear understanding of the impacts of nonideal computations is necessary to fully exploit the efficiency of analog circuits.

Objective Evaluation of the Audibility of Transient Errors in an Adaptive A/D Conversion Channel

DEFF Research Database (Denmark)

Marker-Villumsen, Niels; Jørgensen, Ivan Harald Holger; Bruun, Erik

2014-01-01

An adaptive analog-to-digital conversion channel for audio, using automatic gain control, generates transient errors that may be audible. Evaluating the audibility of such errors requires subjective evaluation using listening tests. From an electrical circuit design point-of-view this is not feas......An adaptive analog-to-digital conversion channel for audio, using automatic gain control, generates transient errors that may be audible. Evaluating the audibility of such errors requires subjective evaluation using listening tests. From an electrical circuit design point...

The Turbo-Fuel-Cell 1.0 - family concept

Science.gov (United States)

Berg, H. P.; Himmelberg, A.; Lehmann, M.; Dückershoff, R.; Neumann, M.

2018-01-01

The “Turbo-Fuel-Cell-Technology” has been described as a MGT-SOFC hybrid system consisting of a recuperated micro gas turbine (MGT) process with an embedded solid oxide fuel cell (SOFC) subsystem. SOFC stacks are connected to “SOFC stack grapes” and are equipped with the so called HEXAR-Module. This module is composed of a high-temperature heat exchanger (HEX), an afterburner (A) and a steam reformer (R). The MGT-concept is based on a generator driven directly by the turbomachine and a recuperator, which returns the exhaust heat to the pressurized compressor outlet air. This provides the necessary base for a highly effective, pure MGT process and the “MGT-SOFC-high-efficiency process”. This paper describes the concept and the thermodynamic background of a highly effective and compact design of the “Turbo-Fuel-Cell 1.0-Family” in the electrical performance class from 100 to 500 kW. The technological state of the system is shown and a rating of the system with comparative parameters is discussed. It becomes visible that all necessary basic technologies should be available and that the technology (for stationary applications) can have the “entry into services (E.I.S.)” in the next 10 years. The MGT-SOFC performance map under different operation conditions is discussed. This article also provides an overview of the research on MGT-SOFC-Systems and the scenario of an energy supply network and a mobile energy conversion of the future introduction.

Experimental assessment of pre-turbo aftertreatment configurations in a single stage turbocharged diesel engine. Part 1: Steady-state operation

OpenAIRE

Luján, José M.; Bermúdez, Vicente; Piqueras, P.; Garcia Afonso, Oscar

2015-01-01

Diesel oxidation catalysts and diesel particulate filters are standard aftertreatment systems in Diesel engines which are traditionally placed downstream of the turbine. However, pre-turbo aftertreatment configurations are being approached as a way to improve the aftertreatment performance in terms of light-off and passive regeneration. This exhaust line architecture can also benefit fuel economy. The objective of this work is to analyse experimentally how the pre-turbo aftertreatment placeme...

On the Comparative Performance Analysis of Turbo-Coded Non-Ideal Sigle-Carrier and Multi-Carrier Waveforms over Wideband Vogler-Hoffmeyer HF Channels

Directory of Open Access Journals (Sweden)

F. Genc

2014-09-01

Full Text Available The purpose of this paper is to compare the turbo-coded Orthogonal Frequency Division Multiplexing (OFDM and turbo-coded Single Carrier Frequency Domain Equalization (SC-FDE systems under the effects of Carrier Frequency Offset (CFO, Symbol Timing Offset (STO and phase noise in wide-band Vogler-Hoffmeyer HF channel model. In mobile communication systems multi-path propagation occurs. Therefore channel estimation and equalization is additionally necessary. Furthermore a non-ideal local oscillator generally is misaligned with the operating frequency at the receiver. This causes carrier frequency offset. Hence in coded SC-FDE and coded OFDM systems; a very efficient, low complex frequency domain channel estimation and equalization is implemented in this paper. Also Cyclic Prefix (CP based synchronization synchronizes the clock and carrier frequency offset.The simulations show that non-ideal turbo-coded OFDM has better performance with greater diversity than non-ideal turbo-coded SC-FDE system in HF channel.

Evaluation of diffusivity in the anterior lobe of the pituitary gland: 3D turbo field echo with diffusion-sensitized driven-equilibrium preparation.

Science.gov (United States)

Hiwatashi, A; Yoshiura, T; Togao, O; Yamashita, K; Kikuchi, K; Kobayashi, K; Ohga, M; Sonoda, S; Honda, H; Obara, M

2014-01-01

3D turbo field echo with diffusion-sensitized driven-equilibrium preparation is a non-echo-planar technique for DWI, which enables high-resolution DWI without field inhomogeneity-related image distortion. The purpose of this study was to evaluate the feasibility of diffusion-sensitized driven-equilibrium turbo field echo in evaluating diffusivity in the normal pituitary gland. First, validation of diffusion-sensitized driven-equilibrium turbo field echo was attempted by comparing it with echo-planar DWI. Five healthy volunteers were imaged by using diffusion-sensitized driven-equilibrium turbo field echo and echo-planar DWI. The imaging voxel size was 1.5 × 1.5 × 1.5 mm(3) for diffusion-sensitized driven-equilibrium turbo field echo and 1.5 × 1.9 × 3.0 mm(3) for echo-planar DWI. ADCs measured by the 2 methods in 15 regions of interests (6 in gray matter and 9 in white matter) were compared by using the Pearson correlation coefficient. The ADC in the pituitary anterior lobe was then measured in 10 volunteers by using diffusion-sensitized driven-equilibrium turbo field echo, and the results were compared with those in the pons and vermis by using a paired t test. The ADCs from the 2 methods showed a strong correlation (r = 0.79; P pituitary gland were 1.37 ± 0.13 × 10(-3) mm(2)/s, which were significantly higher than those in the pons (1.01 ± 0.24 × 10(-3) mm(2)/s) and the vermis (0.89 ± 0.25 × 10(-3) mm(2)/s, P pituitary gland.

T2-weighted MR imaging of liver lesions: a prospective evaluation comparing turbo spin-echo, breath-hold turbo spin-echo and half-Fourier turbo spin-echo (HASTE) sequences; Estudio de lesiones hepaticas con imagenes de resonancia magnetica potenciadas en T2: evaluacion prospectiva comparando secuencias turbo eco del espin, turbo eco del espin con respiracion sostenida y half-Fourier turbo eco del espin (HASTE)

Energy Technology Data Exchange (ETDEWEB)

Martin, J.; Villajos, M.; Oses, M. J.; Veintemillas, M.; Rue, M.; Puig, J.; Sentis, M. [Fundacion Parc Tauli. Sabadell (Spain)

2000-07-01

To compare turbo spin-echo (TSE), breath-hold TSE and half-Fourier acquisition single-shot turbo spin-echo (HASTE) sequences quantitatively and qualitatively in T2-weighted images of liver lesions. The authors evaluated prospectively 89 liver lesions in 73 patients using a 1.0-T magnetic resonance system to compare TSE, breath-hold TSE and HASTE sequences. The quantitative parameters were: lesion-to-liver contrast and lesion-to-liver contrast-to-noise ratio. The qualitative analysis was performed by two observers in consensus who examined four parameters: respiratory artifacts, lesion edge definition, intrahepatic vessel definition and image quality. Repeated measures analysis of variance was utilized to compare the quantitative variables and Friedman's nonparametric test for the qualitative parameters. In quantitative terms, the lesion-to-liver contrast was similar in TSE and breath-hold TSE sequences (2.45{+-}1.44 versus 2.60{+-}1.66), both of which were significantly better than the HASTE sequence (1.12{+-}0.72; p<0.001). The lesion-to-liver contrast-to-noise ratio was significantly higher in the TSE sequence (62.60{+-}46.40 versus 40.22{+-}25.35 versus 50.90{+-}32.10 for TSE, breath-hold TSE and HASTE sequences, respectively; p<0.001). In the qualitative comparisons, the HASTE sequence was significantly better than the TSE and breath-hold TSE sequences (p<0.001) in terms of artifacts and definition of lesion edge and intrahepatic vessels. Image quality was also significantly greater in the HASTE sequence (p<0.001). In quantitative terms, the TSE sequence is better than the breath-hold TSE and HASTE sequences, but there are no movement artifacts in the HASTE sequence, which is also significantly superior to TSE and breath-hold TSE sequences in qualitative terms and, thus, can be employed for T2-weighted images in liver studies. (Author) 17 refs.

Validation of Heat Transfer and Film Cooling Capabilities of the 3-D RANS Code TURBO

Science.gov (United States)

Shyam, Vikram; Ameri, Ali; Chen, Jen-Ping

2010-01-01

The capabilities of the 3-D unsteady RANS code TURBO have been extended to include heat transfer and film cooling applications. The results of simulations performed with the modified code are compared to experiment and to theory, where applicable. Wilcox s k-turbulence model has been implemented to close the RANS equations. Two simulations are conducted: (1) flow over a flat plate and (2) flow over an adiabatic flat plate cooled by one hole inclined at 35 to the free stream. For (1) agreement with theory is found to be excellent for heat transfer, represented by local Nusselt number, and quite good for momentum, as represented by the local skin friction coefficient. This report compares the local skin friction coefficients and Nusselt numbers on a flat plate obtained using Wilcox's k-model with the theory of Blasius. The study looks at laminar and turbulent flows over an adiabatic flat plate and over an isothermal flat plate for two different wall temperatures. It is shown that TURBO is able to accurately predict heat transfer on a flat plate. For (2) TURBO shows good qualitative agreement with film cooling experiments performed on a flat plate with one cooling hole. Quantitatively, film effectiveness is under predicted downstream of the hole.

Thermal efficiency improvement in high output diesel engines a comparison of a Rankine cycle with turbo-compounding

International Nuclear Information System (INIS)

Weerasinghe, W.M.S.R.; Stobart, R.K.; Hounsham, S.M.

2010-01-01

Thermal management, in particular, heat recovery and utilisation in internal combustion engines result in improved fuel economy, reduced emissions, fast warm up and optimized cylinder head temperatures. turbo-compounding is a heat recovery technique that has been successfully used in medium and large scale engines. Heat recovery to a secondary fluid and expansion is used in large scale engines, such as in power plants in the form of heat recovery steam generators (HRSG) . The present paper presents a thermodynamic analysis of turbo-compounding and heat recovery and utilisation through a fluid power cycle, a technique that is also applicable to medium and small scale engines. In a fluid power cycle, the working fluid is stored in a reservoir and expanded subsequently. The reservoir acts as an energy buffer that improves the overall efficiency, significantly. This paper highlights the relative advantage of exhaust heat secondary power cycles over turbo-compounding with the aid of MATLAB based QSS Toolbox simulation results. Steam has been selected as the working fluid in this work for its superior heat capacity over organic fluids and gases.

Traffic Efficiency Evaluation of Elliptical Roundabout Compared with Modern and Turbo Roundabouts Considering Traffic Signal Control

Directory of Open Access Journals (Sweden)

Hadi Hatami

2017-02-01

Full Text Available This paper compared the performance of elliptical roundabout with turbo and modern roundabouts. It considers the effects of increasing the central island radius and speed limit on delay and capacity. Three types of roundabouts (modern, turbo and elliptical roundabouts with different numbers of lanes (single lane, two-lane and three-lane were designed. Unsignalized and signalized controls were applied for these roundabouts. The robustness of the designed roundabouts was investigated for saturated and unsaturated flow conditions. Based on the obtained results, increasing the central island radius had both positive and negative effects on delay and capacity. However, a positive effect on these variables was observed in all roundabouts when increasing the speed limit. In unsignalized and signalized control under unsaturated flow conditions, a modern roundabout had lower delay time than an elliptical roundabout. Moreover, in saturated flow, the elliptical roundabout had the best performance in terms of delay. Overall, in comparison with the turbo roundabouts, modern and elliptical roundabouts had the highest capacities in unsignalized and signalized controls. This study can provide useful information for engineers who decide to design a roundabout.

Modernization of the turbo in the Laguna Verde Nuclear Power Plant

International Nuclear Information System (INIS)

Liebana, B.; Merino, A.; Cobos, A.; Gonzalez, J. J.

2010-01-01

The power increase of the Laguna Verde Nuclear Power Plant is a project for the rehabilitation and modernization of the turbo and associated equipment to get an increase of its power and of its service life. The project scope includes the design, the engineering, the equipment supply, the installation, the testing and the commissioning. This paper describes the first phase of the project.

T2-weighted MR imaging of liver lesions: a prospective evaluation comparing turbo spin-echo, breath-hold turbo spin-echo and half-Fourier turbo spin-echo (HASTE) sequences

International Nuclear Information System (INIS)

Martin, J.; Villajos, M.; Oses, M. J.; Veintemillas, M.; Rue, M.; Puig, J.; Sentis, M.

2000-01-01

To compare turbo spin-echo (TSE), breath-hold TSE and half-Fourier acquisition single-shot turbo spin-echo (HASTE) sequences quantitatively and qualitatively in T2-weighted images of liver lesions. The authors evaluated prospectively 89 liver lesions in 73 patients using a 1.0-T magnetic resonance system to compare TSE, breath-hold TSE and HASTE sequences. The quantitative parameters were: lesion-to-liver contrast and lesion-to-liver contrast-to-noise ratio. The qualitative analysis was performed by two observers in consensus who examined four parameters: respiratory artifacts, lesion edge definition, intrahepatic vessel definition and image quality. Repeated measures analysis of variance was utilized to compare the quantitative variables and Friedman's nonparametric test for the qualitative parameters. In quantitative terms, the lesion-to-liver contrast was similar in TSE and breath-hold TSE sequences (2.45±1.44 versus 2.60±1.66), both of which were significantly better than the HASTE sequence (1.12±0.72; p<0.001). The lesion-to-liver contrast-to-noise ratio was significantly higher in the TSE sequence (62.60±46.40 versus 40.22±25.35 versus 50.90±32.10 for TSE, breath-hold TSE and HASTE sequences, respectively; p<0.001). In the qualitative comparisons, the HASTE sequence was significantly better than the TSE and breath-hold TSE sequences (p<0.001) in terms of artifacts and definition of lesion edge and intrahepatic vessels. Image quality was also significantly greater in the HASTE sequence (p<0.001). In quantitative terms, the TSE sequence is better than the breath-hold TSE and HASTE sequences, but there are no movement artifacts in the HASTE sequence, which is also significantly superior to TSE and breath-hold TSE sequences in qualitative terms and, thus, can be employed for T2-weighted images in liver studies. (Author) 17 refs

LHCb : The LHCb Turbo stream

CERN Multimedia

Puig Navarro, Albert

2015-01-01

The LHCb experiment will record an unprecedented dataset of beauty and charm hadron decays during Run II of the LHC, set to take place between 2015 and 2018. A key computing challenge is to store and process this data, which limits the maximum output rate of the LHCb trigger. So far, LHCb has written out a few kHz of events containing the full raw sub-detector data, which are passed through a full offline event reconstruction before being considered for physics analysis. Charm physics in particular is limited by trigger output rate constraints. A new streaming strategy includes the possibility to perform the physics analysis with candidates reconstructed in the trigger, thus bypassing the offline reconstruction. In the "turbo stream" the trigger will write out a compact summary of "physics" objects containing all information necessary for analyses, and this will allow an increased output rate and thus higher average efficiencies and smaller selection biases. This idea will be commissioned and developed during...

Estado nutricional de niños palúdicos residentes en El Bagre y Turbo, Antioquia, Colombia, 2004-2005

Directory of Open Access Journals (Sweden)

Rosa Magdalena Uscátegui

2007-12-01

Resultados. La prevalencia de niños con desnutrición crónica moderada o grave fue de 22,6%; la de desnutrición global moderada o grave de 10,8% y la aguda de 2,3%. Las prevalencias fueron mayores entre varones y residentes en Turbo. Conclusiones. Las prevalencias de desnutrición fueron superiores a las reportadas en la última Encuesta Nacional de Demografía y Salud (2005, y en los residentes en Turbo fueron mayores a las encontradas en el Urabá antioqueño.

Software approach to automatic patching of analog computer

Science.gov (United States)

1973-01-01

The Automatic Patching Verification program (APV) is described which provides the hybrid computer programmer with a convenient method of performing a static check of the analog portion of his study. The static check insures that the program is patched as specified, and that the computing components being used are operating correctly. The APV language the programmer uses to specify his conditions and interconnections is similar to the FORTRAN language in syntax. The APV control program reads APV source program statements from an assigned input device. Each source program statement is processed immediately after it is read. A statement may select an analog console, set an analog mode, set a potentiometer or DAC, or read from the analog console and perform a test. Statements are read and processed sequentially. If an error condition is detected, an output occurs on an assigned output device. When an end statement is read, the test is terminated.

A New Turbo-shaft Engine Control Law during Variable Rotor Speed Transient Process

Science.gov (United States)

Hua, Wei; Miao, Lizhen; Zhang, Haibo; Huang, Jinquan

2015-12-01

A closed-loop control law employing compressor guided vanes is firstly investigated to solve unacceptable fuel flow dynamic change in single fuel control for turbo-shaft engine here, especially for rotorcraft in variable rotor speed process. Based on an Augmented Linear Quadratic Regulator (ALQR) algorithm, a dual-input, single-output robust control scheme is proposed for a turbo-shaft engine, involving not only the closed loop adjustment of fuel flow but also that of compressor guided vanes. Furthermore, compared to single fuel control, some digital simulation cases using this new scheme about variable rotor speed have been implemented on the basis of an integrated system of helicopter and engine model. The results depict that the command tracking performance to the free turbine rotor speed can be asymptotically realized. Moreover, the fuel flow transient process has been significantly improved, and the fuel consumption has been dramatically cut down by more than 2% while keeping the helicopter level fight unchanged.

VALVE TURBO-ALTERNATOR AS ADDITIONAL HYBRID CAR DEVICE FOR THE HIGH-VOLTAGE BATTERY CHARGE

Directory of Open Access Journals (Sweden)

S. Kolesnikov

2009-01-01

Full Text Available The description of the hybrid car, its drive components and method of the solution of the problem with moving period of the car on electric pulling by means of valve turbo-alternator is given in this article.

Deficiencia de glucosa 6-fostato deshidrogenasa en hombres sanos y en pacientes maláricos; Turbo (Antioquia, Colombia Deficiency of glucose-6-phosphate dehydrogenase in healthy men and malaria patients; Turbo (Antioquia, Colombia

Directory of Open Access Journals (Sweden)

Jaime Carmona-Fonseca

2008-06-01

Full Text Available INTRODUCCIÓN: En América Latina la deficiencia de glucosa 6-fosfato deshidrogenasa (d-G6PD ha sido poco estudiada y en Colombia solo conocemos tres publicaciones antiguas. Urge conocer más la prevalencia de d-G6PD, sobre todo ahora que el tratamiento de la malaria vivax plantea aumentar la dosis diaria o total de primaquina. OBJETIVO: Medir la prevalencia de d-G6PD en poblaciones masculina sana y de enfermos con malaria por Plasmodium vivax, en Turbo (Urabá, departamento de Antioquia, Colombia. METODOLOGÍA: Encuestas de prevalencia, para evaluar la G6PD en dos poblaciones de Turbo (Antioquia: hombres sanos; hombres y mujeres con malaria vivax. Se trabajó con muestras diseñadas con criterios estadístico-epidemiológicos. La actividad enzimática se midió con el método normalizado de Beutler para valorar la G6PD en hemolizados. RESULTADOS: Entre los hombres sanos (n = 508, el intervalo de confianza 95% para el promedio (IC95% estuvo entre 4,15 y 4,51 UI/g hemoglobina y 14,8% presentaron valores por debajo del "límite normal" de INTRODUCTION: Glucose-6-phosphate dehydrogenase (G6PD deficiency in Latin America has not been fully studied and in Colombia only three outdated publications are known. Recent information on the prevalence of G6PD deficiency is required now, because the recommended treatment of vivax malaria requires higher daily or total doses of primaquine. OBJECTIVE: To measure the prevalence of G6PD in a healthy male population and in a Plasmodium vivax infected population in Turbo (Urabá, Antioquia Department, Colombia. METHOD: Prevalence survey to evaluate G6PD in two populations of Turbo (Antioquia: healthy male; male and female with vivax malaria. The work was carried out on population samples selected using statistical and epidemiological criteria. Enzyme activity was measured using Beutler's normalized method to evaluate G6PD after hemolysis. RESULTS: For the healthy male group (n = 508, and with a 95% confidence

14 CFR 121.643 - Fuel supply: Nonturbine and turbo-propeller-powered airplanes: Supplemental operations.

Science.gov (United States)

2010-01-01

... operating nontransport category airplanes type certificated after December 31, 1964, to fly for 30 minutes...-powered airplanes: Supplemental operations. 121.643 Section 121.643 Aeronautics and Space FEDERAL AVIATION... Flight Release Rules § 121.643 Fuel supply: Nonturbine and turbo-propeller-powered airplanes...

Optimal control design of turbo spin-echo sequences with applications to parallel-transmit systems

NARCIS (Netherlands)

Sbrizzi, Alessandro; Hoogduin, Hans; Hajnal, Joseph V; van den Berg, CAT; Luijten, Peter R; Malik, Shaihan J

PURPOSE: The design of turbo spin-echo sequences is modeled as a dynamic optimization problem which includes the case of inhomogeneous transmit radiofrequency fields. This problem is efficiently solved by optimal control techniques making it possible to design patient-specific sequences online.

Engineering & Performance of DuoTurbo: Microturbine with Counter-Rotating Runners

Science.gov (United States)

Biner, D.; Hasmatuchi, V.; Violante, D.; Richard, S.; Chevailler, S.; Andolfatto, L.; Avellan, F.; Münch, C.

2016-11-01

Considering the nuclear phase-out strategy of several European countries and the future tendency to promote renewable energies, the exploitation of small hydropower sites (industrial partners. The modular in-line “plug & play” technology requires low investment, reaching economic feasibility with an available power between 5 kW and 25 kW. One stage of the microturbine consists of two axial counter-rotating runners that form a compact independent unit. Each runner of the turbine holds its own rim generator, the DuoTurbo-configuration involving that each hydraulic runner is integral with each electrical rotor. The possibility of stacking several stages in series enables covering quite a wide range of hydraulic power and, thus, recovering a maximum of energy dissipated in release valves of water supply systems. The present work introduces the global concept of the implemented prototype of the DuoTurbo-microturbine, to target a maximal injected power of 5 kW for a discharge of 9 l/s and a head of 24.5 m per stage. The main features of the hydraulic, the mechanical, the electrical and the electronic design are presented. The hydraulic performance is, then, assessed using CFD simulations for the expected operating range. Finally, the performance measurements of the single-stage prototype installed in the hydraulic test rig of the HES-SO Valais//Wallis are presented.

Polynomial theory of error correcting codes

CERN Document Server

Cancellieri, Giovanni

2015-01-01

The book offers an original view on channel coding, based on a unitary approach to block and convolutional codes for error correction. It presents both new concepts and new families of codes. For example, lengthened and modified lengthened cyclic codes are introduced as a bridge towards time-invariant convolutional codes and their extension to time-varying versions. The novel families of codes include turbo codes and low-density parity check (LDPC) codes, the features of which are justified from the structural properties of the component codes. Design procedures for regular LDPC codes are proposed, supported by the presented theory. Quasi-cyclic LDPC codes, in block or convolutional form, represent one of the most original contributions of the book. The use of more than 100 examples allows the reader gradually to gain an understanding of the theory, and the provision of a list of more than 150 definitions, indexed at the end of the book, permits rapid location of sought information.

SNR-optimized phase-sensitive dual-acquisition turbo spin echo imaging: a fast alternative to FLAIR.

Science.gov (United States)

Lee, Hyunyeol; Park, Jaeseok

2013-07-01

Phase-sensitive dual-acquisition single-slab three-dimensional turbo spin echo imaging was recently introduced, producing high-resolution isotropic cerebrospinal fluid attenuated brain images without long inversion recovery preparation. Despite the advantages, the weighted-averaging-based technique suffers from noise amplification resulting from different levels of cerebrospinal fluid signal modulations over the two acquisitions. The purpose of this work is to develop a signal-to-noise ratio-optimized version of the phase-sensitive dual-acquisition single-slab three-dimensional turbo spin echo. Variable refocusing flip angles in the first acquisition are calculated using a three-step prescribed signal evolution while those in the second acquisition are calculated using a two-step pseudo-steady state signal transition with a high flip-angle pseudo-steady state at a later portion of the echo train, balancing the levels of cerebrospinal fluid signals in both the acquisitions. Low spatial frequency signals are sampled during the high flip-angle pseudo-steady state to further suppress noise. Numerical simulations of the Bloch equations were performed to evaluate signal evolutions of brain tissues along the echo train and optimize imaging parameters. In vivo studies demonstrate that compared with conventional phase-sensitive dual-acquisition single-slab three-dimensional turbo spin echo, the proposed optimization yields 74% increase in apparent signal-to-noise ratio for gray matter and 32% decrease in imaging time. The proposed method can be a potential alternative to conventional fluid-attenuated imaging. Copyright © 2012 Wiley Periodicals, Inc.

Turbo Equalization Techniques Toward Robust PDM 16-QAM Optical Fiber Transmission

DEFF Research Database (Denmark)

Arlunno, Valeria; Caballero Jambrina, Antonio; Borkowski, Robert

2014-01-01

In this paper, we show numerically and experimentally that turbo equalization (TE) is an efficient technique to mitigate performance degradations stemming from optical fiber propagation effects in both optical fiber dispersion managed and unmanaged coherent detection links. The effectiveness....... As TE can be included in the current coherent detection transceiver technologies and complement other equalization techniques, it has prospects for application in next-generation high-capacity and long-reach optical transmission links....

Design and Development of a 200-kW Turbo-Electric Distributed Propulsion Testbed

Science.gov (United States)

Papathakis, Kurt V.; Kloesel, Kurt J.; Lin, Yohan; Clarke, Sean; Ediger, Jacob J.; Ginn, Starr

2016-01-01

The National Aeronautics and Space Administration (NASA) Armstrong Flight Research Center (AFRC) (Edwards, California) is developing a Hybrid-Electric Integrated Systems Testbed (HEIST) Testbed as part of the HEIST Project, to study power management and transition complexities, modular architectures, and flight control laws for turbo-electric distributed propulsion technologies using representative hardware and piloted simulations. Capabilities are being developed to assess the flight readiness of hybrid electric and distributed electric vehicle architectures. Additionally, NASA will leverage experience gained and assets developed from HEIST to assist in flight-test proposal development, flight-test vehicle design, and evaluation of hybrid electric and distributed electric concept vehicles for flight safety. The HEIST test equipment will include three trailers supporting a distributed electric propulsion wing, a battery system and turbogenerator, dynamometers, and supporting power and communication infrastructure, all connected to the AFRC Core simulation. Plans call for 18 high performance electric motors that will be powered by batteries and the turbogenerator, and commanded by a piloted simulation. Flight control algorithms will be developed on the turbo-electric distributed propulsion system.

Evaluation of myelination and myelination disorders with turbo inversion recovery magnetic resonance imaging

International Nuclear Information System (INIS)

Daldrup, H.E.; Schuierer, G.; Link, T.M.; Moeller, H.; Bick, U.; Peters, P.E.; Kurlemann, G.

1997-01-01

The aim of our work was to determine the efficacy of turbo inversion recovery spin echo (TIRSE) pulse sequences in differentiating patients with normal and abnormal myelination. Twenty neurological normal children (aged 5 months to 12 years) as well as 65 children presenting clinically with neurologic developmental deficits (aged 2 months to 10 years) were examined using TIRSE, T1-weighted SE, and T2-weighted turbo SE pulse sequences. Contrast-to-noise-ratio (CNR) between myelinated white and gray matter was compared for the different pulse sequences. In addition, two readers analyzed all images qualitatively by consensus. The CNR values were significantly higher on TIRSE images as compared with conventional images (p < 0.05). Forty-two neurologically abnormal patients displayed a normal myelination on all sequences, whereas 23 showed an abnormal myelination. The TIRSE sequence provided a sensitive and specific depiction of an abnormal myelination in all of these patients. The TIRSE sequence provided additional information to conventional pulse sequences in determining myelination disorders in children, especially in children older than 2 years. (orig.)

Progressive and Error-Resilient Transmission Strategies for VLC Encoded Signals over Noisy Channels

Directory of Open Access Journals (Sweden)

Guillemot Christine

2006-01-01

Full Text Available This paper addresses the issue of robust and progressive transmission of signals (e.g., images, video encoded with variable length codes (VLCs over error-prone channels. This paper first describes bitstream construction methods offering good properties in terms of error resilience and progressivity. In contrast with related algorithms described in the literature, all proposed methods have a linear complexity as the sequence length increases. The applicability of soft-input soft-output (SISO and turbo decoding principles to resulting bitstream structures is investigated. In addition to error resilience, the amenability of the bitstream construction methods to progressive decoding is considered. The problem of code design for achieving good performance in terms of error resilience and progressive decoding with these transmission strategies is then addressed. The VLC code has to be such that the symbol energy is mainly concentrated on the first bits of the symbol representation (i.e., on the first transitions of the corresponding codetree. Simulation results reveal high performance in terms of symbol error rate (SER and mean-square reconstruction error (MSE. These error-resilience and progressivity properties are obtained without any penalty in compression efficiency. Codes with such properties are of strong interest for the binarization of -ary sources in state-of-the-art image, and video coding systems making use of, for example, the EBCOT or CABAC algorithms. A prior statistical analysis of the signal allows the construction of the appropriate binarization code.

Hybrid digital-analog coding with bandwidth expansion for correlated Gaussian sources under Rayleigh fading

Science.gov (United States)

Yahampath, Pradeepa

2017-12-01

Consider communicating a correlated Gaussian source over a Rayleigh fading channel with no knowledge of the channel signal-to-noise ratio (CSNR) at the transmitter. In this case, a digital system cannot be optimal for a range of CSNRs. Analog transmission however is optimal at all CSNRs, if the source and channel are memoryless and bandwidth matched. This paper presents new hybrid digital-analog (HDA) systems for sources with memory and channels with bandwidth expansion, which outperform both digital-only and analog-only systems over a wide range of CSNRs. The digital part is either a predictive quantizer or a transform code, used to achieve a coding gain. Analog part uses linear encoding to transmit the quantization error which improves the performance under CSNR variations. The hybrid encoder is optimized to achieve the minimum AMMSE (average minimum mean square error) over the CSNR distribution. To this end, analytical expressions are derived for the AMMSE of asymptotically optimal systems. It is shown that the outage CSNR of the channel code and the analog-digital power allocation must be jointly optimized to achieve the minimum AMMSE. In the case of HDA predictive quantization, a simple algorithm is presented to solve the optimization problem. Experimental results are presented for both Gauss-Markov sources and speech signals.

The new 1.6 l turbo spark-ignition engine by GM Powertrain Europe; Der neue 1,6-l-Turbo-Ottomotor von GM Powertrain Europe

Energy Technology Data Exchange (ETDEWEB)

Frensch, M.; Heusler, H.; Mohr, J.; Loehnert, T.; Steffens, K. [GM Powertrain Germany GmbH, Ruesselsheim (Germany)

2006-03-15

With this new turbo charged 1.6 l engine, GM Powertrain Europe presents another application from the mid-size gasoline engine family, internally called the Family 1 engine, which was first introduced in 2003. This third variant of the Family 1 Generation 3 architecture will be offered for the first time in the spring of 2006. It is combined with the M32 6-speed transmission in an Opel Meriva OPC as its top-of-the-line engine offering. Using an integrated exhaust manifold turbocharger, the engine reaches a maximum performance of 132 kW and a torque of 230 Nm. (orig.)

Pulsed arterial spin labeling using TurboFLASH with suppression of intravascular signal.

Science.gov (United States)

Pell, Gaby S; Lewis, David P; Branch, Craig A

2003-02-01

Accurate quantification of perfusion with the ADC techniques requires the suppression of the majority of the intravascular signal. This is normally achieved with the use of diffusion gradients. The TurboFLASH sequence with its ultrashort repetition times is not readily amenable to this scheme. This report demonstrates the implementation of a modified TurboFLASH sequence for FAIR imaging. Intravascular suppression is achieved with a modified preparation period that includes a driven equilibrium Fourier transform (DEFT) combination of 90 degrees-180 degrees-90 degrees hard RF pulses subsequent to the inversion delay. These pulses rotate the perfusion-prepared magnetization into the transverse plane where it can experience the suitably placed diffusion gradients before being returned to the longitudinal direction by the second 90 degrees pulse. A value of b = 20-30 s/mm(2) was thereby found to suppress the majority of the intravascular signal. For single-slice perfusion imaging, quantification is only slightly modified. The technique can be readily extended to multislice acquisition if the evolving flow signal after the DEFT preparation is considered. An advantage of the modified preparation scheme is evident in the multislice FAIR images by the preservation of the sign of the magnetization difference. Copyright 2003 Wiley-Liss, Inc.

Influence of Extrinsic Information Scaling Coefficient on Double-Iterative Decoding Algorithm for Space-Time Turbo Codes with Large Number of Antennas

Directory of Open Access Journals (Sweden)

TRIFINA, L.

2011-02-01

Full Text Available This paper analyzes the extrinsic information scaling coefficient influence on double-iterative decoding algorithm for space-time turbo codes with large number of antennas. The max-log-APP algorithm is used, scaling both the extrinsic information in the turbo decoder and the one used at the input of the interference-canceling block. Scaling coefficients of 0.7 or 0.75 lead to a 0.5 dB coding gain compared to the no-scaling case, for one or more iterations to cancel the spatial interferences.

Contrast-enhanced dynamic MR nephrography using the TurboFLASH navigator-gating technique in children

International Nuclear Information System (INIS)

Boss, Andreas; Schaefer, Juergen F.; Claussen, Claus D.; Kueper, Klaus; Schlemmer, Heinz-Peter; Martirosian, Petros; Schick, Fritz; Hacker, Hans-Walter; Darge, Kassa

2006-01-01

The purpose of this work was to test the feasibility of an MR examination protocol for the comprehensive assessment of renal morphology, excretion and split renal function using a navigator-gated TurboFLASH sequence. A navigator-gated T1-weighted single-slice TurboFLASH sequence suitable for dynamic MR urography and nephrography was implemented. A protocol was developed allowing for assessment of urinary excretion and split renal function by recording the renal clearance of a gadolinium (Gd) diethylene-triamine-pentacetic-acid (DTPA) bolus. Ten patients aged between 14 months and 14 years (mean age 4.8±4.6 years) were evaluated with the following indications: pelvicalyceal dilatation (n=4), follow-up after pyeloplasty (n=1), duplex systems (n=3), large renal cyst (n=1), and renal insufficiency (n=1). Dynamic MR urography and MR split renal function were compared to MAG3 scintigraphy. Evaluation of morphology, excretion and function required 50-60 minutes examination time, plus 10 minutes for post-processing. The TurboFLASH sequence yielded image acquisition at nearly identical diaphragm positions allowing for accurate region-of-interest evaluation within the renal parenchyma and the urinary passage. Static and dynamic MR urography showed the morphology of the urinary tract and excretion with sufficient diagnostic imaging quality, and the results were in diagnostic compliance with scintigraphy. MRI and scintigraphy yielded similar results for split renal function with a correlation coefficient of R=0.968 determined by linear regression. Our conclusions were that the method is robust, easy to perform on a clinical 1.5 T MRI system, rapid to evaluate and post-process and, therefore, easy to incorporate into clinical routine. Compared to scintigraphy, the higher spatial resolution of the MR examination provides additional important information improving the management of the pediatric patients without the application of radioactive tracers. (orig.)

Analog fault diagnosis by inverse problem technique

KAUST Repository

Ahmed, Rania F.

2011-12-01

A novel algorithm for detecting soft faults in linear analog circuits based on the inverse problem concept is proposed. The proposed approach utilizes optimization techniques with the aid of sensitivity analysis. The main contribution of this work is to apply the inverse problem technique to estimate the actual parameter values of the tested circuit and so, to detect and diagnose single fault in analog circuits. The validation of the algorithm is illustrated through applying it to Sallen-Key second order band pass filter and the results show that the detecting percentage efficiency was 100% and also, the maximum error percentage of estimating the parameter values is 0.7%. This technique can be applied to any other linear circuit and it also can be extended to be applied to non-linear circuits. © 2011 IEEE.

Study of heat insulated turbo compound engine. Shanetsugata tabo konpaundo engine to tomoni ayumu

Energy Technology Data Exchange (ETDEWEB)

Hirai, K [Isuzu Motors Ltd., Tokyo (Japan). Ceramics Research Lab.

1994-02-01

For a main purpose of development of the heat insulated turbo compound engine using the ceramics, the Isuzu Ceramics Inst. Co., Ltd. was established by the Isuzu Motors Ltd. in 1988. The main study subjects take up various topics such as a development of the new engine system for actualizing a low fuel consumption and low emission, an improvement of deteriorated combustion caused by the insulation, a development of energy recovery facility for utilizing effectively the exhaust energy from the engines, a development of power electronics technology for controlling the recovery facility, a study and development of ceramics as the insulation material and so forth. The outstanding characteristics of this institute are that a development of the heat insulated turbo compound engine is set as the main study subject, but at the same time that a commercialization of the various derivation technology derived from this study. Even just the main study subjects currently under way are counted up to a number close to 10 items, and consequently the efforts are being continued in each field assigned for solving the subjects. 6 figs.

Modelling of the heat load in the piston of turbo diesel engine - continuation

Directory of Open Access Journals (Sweden)

Piotr GUSTOF

2007-01-01

Full Text Available In this study the mathematical description of characteristic surfaces of the heat exchange of the piston and temperature distribution of the turbo diesel engine at the beginning phase its work was presented. The computations were performed by means of the two-zone combustion model, the boundary conditions of III kind and the finite elements method (MES by using of COSMOS/M program.

Determination of Permissible Short-Time Emergency Overloading of Turbo-Generators and Synchronous Compensators

Directory of Open Access Journals (Sweden)

V. A. Anischenko

2011-01-01

Full Text Available The paper shows that failure to take into account variable ratio of short-time emergency overloading of turbo-generators (synchronous compensators that can lead to underestimation of overloading capacity or impermissible insulation over-heating.A method has been developed for determination of permissible duration of short-time emergency over-loading that takes into account changes of over-loading ratio in case of a failure.

Empirical study of classification process for two-stage turbo air classifier in series

Science.gov (United States)

Yu, Yuan; Liu, Jiaxiang; Li, Gang

2013-05-01

The suitable process parameters for a two-stage turbo air classifier are important for obtaining the ultrafine powder that has a narrow particle-size distribution, however little has been published internationally on the classification process for the two-stage turbo air classifier in series. The influence of the process parameters of a two-stage turbo air classifier in series on classification performance is empirically studied by using aluminum oxide powders as the experimental material. The experimental results show the following: 1) When the rotor cage rotary speed of the first-stage classifier is increased from 2 300 r/min to 2 500 r/min with a constant rotor cage rotary speed of the second-stage classifier, classification precision is increased from 0.64 to 0.67. However, in this case, the final ultrafine powder yield is decreased from 79% to 74%, which means the classification precision and the final ultrafine powder yield can be regulated through adjusting the rotor cage rotary speed of the first-stage classifier. 2) When the rotor cage rotary speed of the second-stage classifier is increased from 2 500 r/min to 3 100 r/min with a constant rotor cage rotary speed of the first-stage classifier, the cut size is decreased from 13.16 μm to 8.76 μm, which means the cut size of the ultrafine powder can be regulated through adjusting the rotor cage rotary speed of the second-stage classifier. 3) When the feeding speed is increased from 35 kg/h to 50 kg/h, the "fish-hook" effect is strengthened, which makes the ultrafine powder yield decrease. 4) To weaken the "fish-hook" effect, the equalization of the two-stage wind speeds or the combination of a high first-stage wind speed with a low second-stage wind speed should be selected. This empirical study provides a criterion of process parameter configurations for a two-stage or multi-stage classifier in series, which offers a theoretical basis for practical production.

Detecting analogical resemblance without retrieving the source analogy.

Science.gov (United States)

Kostic, Bogdan; Cleary, Anne M; Severin, Kaye; Miller, Samuel W

2010-06-01

We examined whether people can detect analogical resemblance to an earlier experimental episode without being able to recall the experimental source of the analogical resemblance. We used four-word analogies (e.g., robin-nest/beaver-dam), in a variation of the recognition-without-cued-recall method (Cleary, 2004). Participants studied word pairs (e.g., robin-nest) and were shown new word pairs at test, half of which analogically related to studied word pairs (e.g., beaver-dam) and half of which did not. For each test pair, participants first attempted to recall an analogically similar pair from the study list. Then, regardless of whether successful recall occurred, participants were prompted to rate the familiarity of the test pair, which was said to indicate the likelihood that a pair that was analogically similar to the test pair had been studied. Across three experiments, participants demonstrated an ability to detect analogical resemblance without recalling the source analogy. Findings are discussed in terms of their potential relevance to the study of analogical reasoning and insight, as well as to the study of familiarity and recognition memory.

Analysis and Implementation of Hard-Decision Viterbi Decoding In Wireless Communication over AWGN Channel

OpenAIRE

Muhammad Asif; H.M.Rehan Afzal

2015-01-01

Convolutional codes are also known as Turbo codes because of their error correction capability. These codes are also awarded as Super product codes, because these codes have replaced the backward error correction codes. Turbo codes are much more efficient than previous backward error correction codes because these are Forward error correction (FEC) codes and there is no need for a feedback link to request the transmitter for retransmission of data, when bits are corrupted in the i...

Assessment of diagnosing metastatic bone tumor on T2*-weighted images. Comparison between turbo spin echo (TSE) method and gradient echo (GE) method

International Nuclear Information System (INIS)

Hayashi, Takahiko; Sugiyama, Akira; Katayama, Motoyuki

1996-01-01

We examined the usefulness of T2 * weighted gradient field echo images for diagnosis for metastatic bone tumors in comparison with T2 weighted turbo spin echo (fast spin echo) images. In T2 * weighted gradient field echo sequence to obtain maximum contrast-to-noise ratio (CNR), we experimentally manipulated flip angle (FA) (5deg-90deg), repetition time (TR) (400, 700 msec), and echo time (TE) (10-50 msec). The best CNR was 16.4 in fast low angle shot (FLASH) (TE: 24 msec, TR: 700 msec, FA: 40deg). Magnetic resonance imaging was carried out in 28 patients with metastatic bone tumors. In addition to conventional T1 weighted spin echo images, T2 weighted turbo spin echo (fast spin echo images) and T2 * weighted gradient field echo images were obtained. T2 * weighted gradient field echo images were superior to T2 weighted turbo spin echo (fast spin echo) images in delineating the tumors, adjacent fat tissues, and bone marrow. (author)

Validation of DIVA: an expert system for the diagnostic of turbo-generator vibrations

International Nuclear Information System (INIS)

Chevalier, R.; Ricard, B.; Tiarri, J.P.; Bonnet, J.C.

1990-01-01

The project presented in this paper concerns the development of an expert system dealing with the diagnosis of turbo-generator vibrations. DIVA - Diagnosis of Shaft Line Vibrations - is a joint project which is carried out by ALSTHOM, Electricite de France and Laboratoire de Marcoussis, research centre of CGE. This article first presents the organisation of the system and then the goals and results of the tests already achieved [fr

Operational Safety Assessment of Turbo Generators with Wavelet Rényi Entropy from Sensor-Dependent Vibration Signals

Directory of Open Access Journals (Sweden)

Xiaoli Zhang

2015-04-01

Full Text Available With the rapid development of sensor technology, various professional sensors are installed on modern machinery to monitor operational processes and assure operational safety, which play an important role in industry and society. In this work a new operational safety assessment approach with wavelet Rényi entropy utilizing sensor-dependent vibration signals is proposed. On the basis of a professional sensor and the corresponding system, sensor-dependent vibration signals are acquired and analyzed by a second generation wavelet package, which reflects time-varying operational characteristic of individual machinery. Derived from the sensor-dependent signals’ wavelet energy distribution over the observed signal frequency range, wavelet Rényi entropy is defined to compute the operational uncertainty of a turbo generator, which is then associated with its operational safety degree. The proposed method is applied in a 50 MW turbo generator, whereupon it is proved to be reasonable and effective for operation and maintenance.

Impact of Turbocharger Non-Adiabatic Operation on Engine Volumetric Efficiency and Turbo Lag

Directory of Open Access Journals (Sweden)

S. Shaaban

2012-01-01

Full Text Available Turbocharger performance significantly affects the thermodynamic properties of the working fluid at engine boundaries and hence engine performance. Heat transfer takes place under all circumstances during turbocharger operation. This heat transfer affects the power produced by the turbine, the power consumed by the compressor, and the engine volumetric efficiency. Therefore, non-adiabatic turbocharger performance can restrict the engine charging process and hence engine performance. The present research work investigates the effect of turbocharger non-adiabatic performance on the engine charging process and turbo lag. Two passenger car turbochargers are experimentally and theoretically investigated. The effect of turbine casing insulation is also explored. The present investigation shows that thermal energy is transferred to the compressor under all circumstances. At high rotational speeds, thermal energy is first transferred to the compressor and latter from the compressor to the ambient. Therefore, the compressor appears to be “adiabatic” at high rotational speeds despite the complex heat transfer processes inside the compressor. A tangible effect of turbocharger non-adiabatic performance on the charging process is identified at turbocharger part load operation. The turbine power is the most affected operating parameter, followed by the engine volumetric efficiency. Insulating the turbine is recommended for reducing the turbine size and the turbo lag.

Evaluation of Data with Systematic Errors

International Nuclear Information System (INIS)

Froehner, F. H.

2003-01-01

Application-oriented evaluated nuclear data libraries such as ENDF and JEFF contain not only recommended values but also uncertainty information in the form of 'covariance' or 'error files'. These can neither be constructed nor utilized properly without a thorough understanding of uncertainties and correlations. It is shown how incomplete information about errors is described by multivariate probability distributions or, more summarily, by covariance matrices, and how correlations are caused by incompletely known common errors. Parameter estimation for the practically most important case of the Gaussian distribution with common errors is developed in close analogy to the more familiar case without. The formalism shows that, contrary to widespread belief, common ('systematic') and uncorrelated ('random' or 'statistical') errors are to be added in quadrature. It also shows explicitly that repetition of a measurement reduces mainly the statistical uncertainties but not the systematic ones. While statistical uncertainties are readily estimated from the scatter of repeatedly measured data, systematic uncertainties can only be inferred from prior information about common errors and their propagation. The optimal way to handle error-affected auxiliary quantities ('nuisance parameters') in data fitting and parameter estimation is to adjust them on the same footing as the parameters of interest and to integrate (marginalize) them out of the joint posterior distribution afterward

Analyses on the Performance and Interaction Between the Impeller and Casing in a Small-Size Turbo-Compressor

Science.gov (United States)

Kim, Youn-Jea; Kim, Dong-Won

The effects of casing shapes on the performance and the interaction between an impeller and a casing in a small-size turbo-compressor are investigated. Numerical analysis is conducted for the turbo-compressor with circular and single volute casings from the inlet to a discharge nozzle. The optimum design for each element is important to develop the small-size turbo-compressor using alternative refrigerant as a working fluid. Typically, the rotating speed of the compressor is in the range of 40000-45000rpm because of the small size of an impeller diameter. A blade of an impeller has backswept two-dimensional shape due to tip clearance and a vane diffuser has wedge type. In order to predict the flow pattern inside the entire impeller, the vaneless diffuser and the casing, calculations with multiple frames of reference method between the rotating and stationery parts of the domain are carried out. For compressible turbulent flow fields, the continuity and time-averaged three-dimensional Navier-Stokes equations are employed. To evaluate the performance of two types of casings, the static pressure recovery and loss coefficients are obtained with various flow rates. Also, static pressure distributions around casings are studied for different casing shapes, which are very important to predict the distribution of radial load. To prove the accuracy of numerical results, measurements of static pressure around the casing and pressure difference between the inlet and the outlet of the compressor are performed for the circular casing. The comparison of experimental and numerical results is conducted, and reasonable agreement is obtained.

An analog computer method for solving flux distribution problems in multi region nuclear reactors

Energy Technology Data Exchange (ETDEWEB)

Radanovic, L; Bingulac, S; Lazarevic, B; Matausek, M [Boris Kidric Institute of Nuclear Sciences Vinca, Beograd (Yugoslavia)

1963-04-15

The paper describes a method developed for determining criticality conditions and plotting flux distribution curves in multi region nuclear reactors on a standard analog computer. The method, which is based on the one-dimensional two group treatment, avoids iterative procedures normally used for boundary value problems and is practically insensitive to errors in initial conditions. The amount of analog equipment required is reduced to a minimum and is independent of the number of core regions and reflectors. (author)

Development of elements of the condition monitoring system of turbo generators of thermal power stations and nuclear power plants

Science.gov (United States)

Kumenko, A. I.; Kostyukov, V. N.; Kuz'minykh, N. Yu.; Boichenko, S. N.; Timin, A. V.

2017-08-01

The rationale is given for the improvement of the regulatory framework for the use of shaft sensors for the in-service condition monitoring of turbo generators and the development of control systems of shaft surfacing and misalignments of supports. A modern concept and a set of methods are proposed for the condition monitoring of the "shaft line-thrust bearing oil film-turbo generator supports" system elements based on the domestic COMPACS® technology. The system raw data are design, technology, installation, and operating parameters of the turbo generator as well as measured parameters of the absolute vibration of supports and mechanical quantities, relative displacements and relative vibration of the rotor teeth in accordance with GOST R 55263-2012. The precalculated shaft line assembly line in the cold state, the nominal parameters of rotor teeth positions on the dynamic equilibrium curve, the static and dynamic characteristics of the oil film of thrust bearings, and the shaft line stiffness matrix of unit support displacements have been introduced into the system. Using the COMPACS-T system, it is planned to measure positions and oscillations of rotor teeth, to count corresponding static and dynamic characteristics of the oil film, and the static and dynamic loads in the supports in real time. Using the obtained data, the system must determine the misalignments of supports and corrective alignments of rotors of coupling halves, voltages in rotor teeth, welds, and bolts of the coupling halves, and provide automatic conclusion if condition monitoring parameters correspond to standard values. A part of the methodological support for the proposed system is presented, including methods for determining static reactions of supports under load, the method for determining shaft line stiffness matrices, and the method for solving the inverse problem, i.e., the determination of the misalignments of the supports by measurements of rotor teeth relative positions in bearing

Analogical scaffolding: Making meaning in physics through representation and analogy

Science.gov (United States)

Podolefsky, Noah Solomon

This work reviews the literature on analogy, introduces a new model of analogy, and presents a series of experiments that test and confirm the utility of this model to describe and predict student learning in physics with analogy. Pilot studies demonstrate that representations (e.g., diagrams) can play a key role in students' use of analogy. A new model of analogy, Analogical Scaffolding, is developed to explain these initial empirical results. This model will be described in detail, and then applied to describe and predict the outcomes of further experiments. Two large-scale (N>100) studies will demonstrate that: (1) students taught with analogies, according to the Analogical Scaffolding model, outperform students taught without analogies on pre-post assessments focused on electromagnetic waves; (2) the representational forms used to teach with analogy can play a significant role in student learning, with students in one treatment group outperforming students in other treatment groups by factors of two or three. It will be demonstrated that Analogical Scaffolding can be used to predict these results, as well as finer-grained results such as the types of distracters students choose in different treatment groups, and to describe and analyze student reasoning in interviews. Abstraction in physics is reconsidered using Analogical Scaffolding. An operational definition of abstraction is developed within the Analogical Scaffolding framework and employed to explain (a) why physicists consider some ideas more abstract than others in physics, and (b) how students conceptions of these ideas can be modeled. This new approach to abstraction suggests novel approaches to curriculum design in physics using Analogical Scaffolding.

Strength analysis of an aircraft turbo-compressor engine turbine disc

Science.gov (United States)

Klimko, Marek

2017-09-01

This article deals with a strength analysis of a gas turbine rotor disc of the concrete type of an aircraft turbo-compressor engine (ATCE). The introductory part is dedicated to a basic description of the given engine, including the main technical parameters entering the calculation. The calculation is carried out by the finite difference method. This method allows to determine the tension of a generally shaped disc, which is affected by centrifugal forces of its weight, external load and heat stress caused by the difference of thermal gradients along the disc radius. The result of calculations are dependencies of the most important parameters, such as the reduced stress, radial stress, or the safety coefficient along the disc radius.

Error compensation for hybrid-computer solution of linear differential equations

Science.gov (United States)

Kemp, N. H.

1970-01-01

Z-transform technique compensates for digital transport delay and digital-to-analog hold. Method determines best values for compensation constants in multi-step and Taylor series projections. Technique also provides hybrid-calculation error compared to continuous exact solution, plus system stability properties.

Property-Based Monitoring of Analog and Mixed-Signal Systems

Science.gov (United States)

Havlicek, John; Little, Scott; Maler, Oded; Nickovic, Dejan

In the recent past, there has been a steady growth of the market for consumer embedded devices such as cell phones, GPS and portable multimedia systems. In embedded systems, digital, analog and software components are combined on a single chip, resulting in increasingly complex designs that introduce richer functionality on smaller devices. As a consequence, the potential insertion of errors into a design becomes higher, yielding an increasing need for automated analog and mixed-signal validation tools. In the purely digital setting, formal verification based on properties expressed in industrial specification languages such as PSL and SVA is nowadays successfully integrated in the design flow. On the other hand, the validation of analog and mixed-signal systems still largely depends on simulation-based, ad-hoc methods. In this tutorial, we consider some ingredients of the standard verification methodology that can be successfully exported from digital to analog and mixed-signal setting, in particular property-based monitoring techniques. Property-based monitoring is a lighter approach to the formal verification, where the system is seen as a "black-box" that generates sets of traces, whose correctness is checked against a property, that is its high-level specification. Although incomplete, monitoring is effectively used to catch faults in systems, without guaranteeing their full correctness.

MACROINVERTEBRADOS ASOCIADOS A LAS RAÍCES SUMERGIDAS DEL MANGLE ROJO (Rhizophora mangle EN LAS BAHÍAS TURBO Y EL UNO, GOLFO DE URABÁ (CARIBE COLOMBIANO

Directory of Open Access Journals (Sweden)

GARCÍA PADILLA JESÚS MARÍA

2010-05-01

Full Text Available Con el fin de establecer el comportamiento de la salinidad y las características de la fauna de macroinvertebrados asociados a las raíces de Rhizophora mangle en las Bahías de Turbo y El Uno, se realizaron cuatro muestreos entre septiembre del 2004 y febrero del 2005, en tres sectores de las Bahías. Los valores de salinidad experimentaron cambios muy importantes en el tiempo y fluctuaron entre 2 y 32 unidades. En total, se cuantificaron 26 especies en Bahía Turbo y 28 en Bahía El Uno. Mientras la diversidad en la Bahía Turbo varió entre 0,77 en septiembre y 2,22 noviembre, en Bahía El Uno, los valores fluctuaron entre 1,14 en noviembre y 1,95 en septiembre. La mayoría de las especies son frecuentes en las raíces de mangle de la región caribe y poseen un carácter eurihalino.

What role for the anterior cingulate in analogical reasoning?

Science.gov (United States)

O'Boyle, Michael W

2010-06-01

Abstract While prefrontal and frontal cortex of the brain are well documented to mediate many executive functions, including creativity, flexibility, and adaptability, the anterior cingulate cortex (ACC) is known to be involved in error detection and conflict resolution, and is crucial to reward-based learning. A case is made for the notion that any neural model of analogical reasoning must incorporate the critical (and specialized) contributions of the ACC.

Determination of vitality in myocardial infarction. Comparison of single- and multi-slice MRI techniques with TurboFlash and TrueFISP sequences

International Nuclear Information System (INIS)

Huber, A.; Schoenberg, S.O.; Spannagl, B.; Rieber, J.; Klauss, V.; Reiser, M.F.

2004-01-01

The aim of the study was to compare the diagnostic accuracy in imaging viability of the myocardium with a multislice inversions recovery 2D single shot TrueFISP sequence and an established inversion recovery TurboFlash sequence. Twelve patients with myocardial infarction were examined at a 1.5 tesla MR system (Sonata, Siemens, Medical Systems) 10 min after application of a single dose multihance (0,1 mmol/kg body weight) with a 2D multislice technique (inversion recovery single shot TrueFISP), that allows to image the entire short axis during one breathhold and a 2D single slice technique (inversion recovery TurboFlash), that requires one breathhold per slice. Signal intensity was determined in normal myocardium, in the infarcted myocardium and in the left ventricle. The contrast/noise ratio of normal and infarcted myocardium was determined. The areas of hyperintense infarction were compared for both sequence techniques. The multislice single shot 2D IR-TrueFisp sequence has a lower contrast/noise ratio than the IR-TurboFlash sequence (mean values 6.9 vs. 12.5) for viable and non viable myocardium. The assessment of the volume of the infarction is possible with excellent correlation of both techniques (r=0.97, p [de

Detecting analogies unconsciously

Directory of Open Access Journals (Sweden)

Thomas Peter Reber

2014-01-01

Full Text Available Analogies may arise from the conscious detection of similarities between a present and a past situation. In this functional magnetic resonance imaging study, we tested whether young volunteers would detect analogies unconsciously between a current supraliminal (visible and a past subliminal (invisible situation. The subliminal encoding of the past situation precludes awareness of analogy detection in the current situation. First, participants encoded subliminal pairs of unrelated words in either one or nine encoding trials. Later, they judged the semantic fit of supraliminally presented new words that either retained a previously encoded semantic relation (‘analog’ or not (‘broken analog’. Words in analogs versus broken analogs were judged closer semantically, which reflects unconscious analogy detection. Hippocampal activity associated with subliminal encoding correlated with the behavioral measure of unconscious analogy detection. Analogs versus broken analogs were processed with reduced prefrontal but enhanced medial temporal activity. We conclude that analogous episodes can be detected even unconsciously drawing on the episodic memory network.

Plan de marketing para el posicionamiento de mercado del Taller Automotriz "Los Turbos".

OpenAIRE

Lomas Lomas, Shirley Karina; Riera Cevallos, Jenny Belén

2015-01-01

Propuesta de un plan de marketing para mejorar el posicionamiento del taller automotriz “Los Turbos”, a través de la evaluación del comportamiento del cliente y el diseño de estrategias, que permitan al negocio obtener una ventaja competitiva, incrementando la cuota de mercado y las ventas crezcan. Proposal for a marketing plan to improve the positioning of the business "Turbos", through the evaluation of customer behavior and designing strategies that allow the business to obtain a ...

High technology at 'General Turbo', DH 12/13 balance-over speed testing stand

International Nuclear Information System (INIS)

Nuta, Florian Nicolae; Vasiliu, Dinu; Mauna, Traian

2005-01-01

'General Turbo' activity started in 1970 including building the balancing and over speed stand. DH 12/13 is the latest up-to-date facility of this type, the best one of the five in Europe, and was commissioned in 2004. The facility was especially built to be used for Romanian Nuclear Power Plant rotor testing and also for thermal very big rotors. The paper underlines the main attributes and the components of the facility DH 12/13 based on the Schenck technology. (authors)

Geometry Analysis and Effect of Turbulence Model on the Radial Rotor Turbo-Expander Design for Small Organic Rankine Cycle System

Directory of Open Access Journals (Sweden)

Maulana Arifin

2015-07-01

Full Text Available Organic Rankine Cycle (ORC is one of the most promising technology for small electric power generations. The geometry analysis and the effect of turbulence model on the radial turbo-expanders design for small ORC power generation systems were discussed in this paper. The rotor blades and performance were calculated using several working fluids such as R134a, R143a, R245fa, n-Pentane, and R123. Subsequently, a numerical study was carried out in the fluid flow area with R134a and R123 as the working fluids. Analyses were performed using Computational Fluid Dynamics (CFD ANSYS Multiphysics on two real gas models, with the k-epsilon and SST (shear stress transport turbulence models. The result shows the distribution of Mach number, pressure, velocity and temperature along the rotor blade of the radial turbo-expanders and estimation of performance at various operating conditions. The operating conditions are as follow: 250,000 grid mesh flow area, real gas model SST at steady state condition, 0.4 kg/s of mass flow rate, 15,000 rpm rotor speed, 5 bar inlet pressure, and 373K inlet temperature. By using those conditions, CFD analysis shows that the turbo-expander able to produce 6.7 kW and 5.5 kW of power when using R134a and R123, respectively.

Improved visualization of collateral ligaments of the ankle: multiplanar reconstructions based on standard 2D turbo spin-echo MR images

International Nuclear Information System (INIS)

Duc, Sylvain R.; Mengiardi, Bernard; Pfirrmann, Christian W.A.; Hodler, Juerg; Zanetti, Marco

2007-01-01

The purpose of the study was to evaluate the visualization of the collateral ankle ligaments on multiplanar reconstructions (MPR) based on standard 2D turbo spin-echo images. Coronal and axial T2-weighted turbo spin-echo and MPR angled parallel to the course of the ligaments of 15 asymptomatic and 15 symptomatic ankles were separately analyzed by two musculoskeletal radiologists. Image quality was assessed in the asymptomatic ankles qualitatively. In the symptomatic ankles interobserver agreement and reader confidence was determined for each ligament. On MPR the tibionavicular and calcaneofibular ligaments were more commonly demonstrated on a single image than on standard MR images (reader 1: 13 versus 0, P=0.002; reader 2: 14 versus 1, P=0.001 and reader 1: 13 versus 2, P=0.001; reader 2: 14 versus 0, P<0.001). The tibionavicular ligament was considered to be better delineated on MPR by reader 1 (12 versus 3, P=0.031). In the symptomatic ankles, reader confidence was greater with MPR for all ligaments except for the tibiocalcanear ligament (both readers) and the anterior and posterior talofibular ligaments (for reader 2). Interobserver agreement was increased with MPR for the tibionavicular ligament. Multiplanar reconstructions of 2D turbo spin-echo images improve the visualization of the tibionavicular and calcaneofibular ligaments and strengthen diagnostic confidence for these ligaments. (orig.)

A verification plan of rotor dynamics of turbo-machine system supported by AMB for the GTHTR300 (step 1)

International Nuclear Information System (INIS)

Takizuka, Takakazu; Takada, Shoji; Kosugiyama, Shinichi; Kunitomi, Kazuhiko; Xing, Yan

2003-01-01

A program for research and development on magnetic bearing suspended rotor dynamics was planned for the Gas Turbine High Temperature Reactor (GTHTR300) plant. The magnetic bearing to suspend the turbo-machine rotor of GTHTR300 is unique because the required load capacity is much larger than that of existing one. The turbo-compressor and generator rotors, each of which is suspended by two radial bearings, pass over the first and the second critical speeds to bending mode, respectively. The rotor design fulfilled the standard limit of vibration amplitude of 75 μm at the rated rotational speed by optimising the stiffness of the magnetic bearings. A test apparatus was designed in the program. The test apparatus is composed of 1/3-scale two test rotors simulating turbo-compressor and generator rotors which are connected by a flexible coupling or a rigid coupling. Because the load capacity is almost in proportion to the projected area of the bearing, the load capacity of the magnetic bearing is almost 1/10 of the actual one. The test rotors were designed so that their critical speeds and vibration modes match the actual ones. The test will verify the rotor design and demonstrate the rotor vibration control technology of the magnetic bearing. This paper shows the outline of the test device and the test plan for the magnetic bearing suspended rotor system. The present study is entrusted from the Ministry of Education, Culture, Sports, Science and Technology of Japan. (author)

Two-stage turbo-compressor for heat pumps. Stage 1: Feasibility study; Compresseur radial pour pompe a chaleur bietagee. Phase 1: etude de faisabilite

Energy Technology Data Exchange (ETDEWEB)

Shiffmann, J; Molyneaux, A [Ofttech SA, Parc Scientifique de l' EPFL-C, Lausanne (Switzerland); Favrat, D; Marechal, F; Zehnder, M; Godat, J [Swiss Federal Institue of Technology (EPFL), Laboratoire d' energetique industrielle, Lausanne (Switzerland)

2002-07-01

This report describes the work performed by Ofttech SA, in collaboration with the Industrial Energy Laboratory (LENI) of the Swiss Federal Institute of Technology (EPFL) in Lausanne, investigating the feasibility of designing an oil-free turbo-compressor for domestic retrofit heat pump applications. The primary objective for a retrofit heat pump is that it produces heating water at 60 {sup o}C (with at least 10 {sup o}C temperature rise) with an external air temperature of -12 {sup o}C and can supply at least 10 kW. This would enable the air-water heat pump to directly replace oil or gas boilers. To enable a heat pump to produce the required hot water with a sufficient Coefficient of Performance (COP) a two-stage compressor is the most sensible technical solution currently available. This report shows how a turbo-compressor consisting of a single rotor with two centrifugal compressor wheels, running at variable speeds up to 240,000 rpm, can provide a unique solution with better predicted performance than existing solutions. This is possible by the use of bearings lubricated with gaseous refrigerant - excluding completely the need for oil in the system with its associated heat transfer, system, environmental and cost disadvantages. These bearings need radial clearances between 5 and 10 micrometers, leading to manufacturing tolerances in the order of magnitude of one micrometer. Various possible refrigerants are discussed with R134a being chosen for this study. Investigations performed by the company Asea Brown Boveri (ABB) are reported showing the possible design of the two small turbo-compressors resulting in wheels of less than 20 mm. The electric motor for this directly driven compressor together with the wheels and gas bearings will result in a complete rotor of less than 100 mm long - making it smaller, lighter and cheaper than existing compressors. The main conclusion is that the overall performance of this novel turbo-compressor when compared with the

Automatic activation of categorical and abstract analogical relations in analogical reasoning.

Science.gov (United States)

Green, Adam E; Fugelsang, Jonathan A; Dunbar, Kevin N

2006-10-01

We examined activation of concepts during analogical reasoning. Subjects made either analogical judgments or categorical judgments about four-word sets. After each four-word set, they named the ink color of a single word in a modified Stroop task. Words that referred to category relations were primed (as indicated by longer response times on Stroop color naming) subsequent to analogical judgments and categorical judgments. This finding suggests that activation of category concepts plays a fundamental role in analogical thinking. When colored words referred to analogical relations, priming occurred subsequent to analogical judgments, but not to categorical judgments, even though identical four-word stimuli were used for both types of judgments. This finding lends empirical support to the hypothesis that, when people comprehend the analogy between two items, they activate an abstract analogical relation that is distinct from the specific content items that compose the analogy.

Analog computing

CERN Document Server

Ulmann, Bernd

2013-01-01

This book is a comprehensive introduction to analog computing. As most textbooks about this powerful computing paradigm date back to the 1960s and 1970s, it fills a void and forges a bridge from the early days of analog computing to future applications. The idea of analog computing is not new. In fact, this computing paradigm is nearly forgotten, although it offers a path to both high-speed and low-power computing, which are in even more demand now than they were back in the heyday of electronic analog computers.

Turbo-Satori: a neurofeedback and brain-computer interface toolbox for real-time functional near-infrared spectroscopy.

Science.gov (United States)

Lührs, Michael; Goebel, Rainer

2017-10-01

Turbo-Satori is a neurofeedback and brain-computer interface (BCI) toolbox for real-time functional near-infrared spectroscopy (fNIRS). It incorporates multiple pipelines from real-time preprocessing and analysis to neurofeedback and BCI applications. The toolbox is designed with a focus in usability, enabling a fast setup and execution of real-time experiments. Turbo-Satori uses an incremental recursive least-squares procedure for real-time general linear model calculation and support vector machine classifiers for advanced BCI applications. It communicates directly with common NIRx fNIRS hardware and was tested extensively ensuring that the calculations can be performed in real time without a significant change in calculation times for all sampling intervals during ongoing experiments of up to 6 h of recording. Enabling immediate access to advanced processing features also allows the use of this toolbox for students and nonexperts in the field of fNIRS data acquisition and processing. Flexible network interfaces allow third party stimulus applications to access the processed data and calculated statistics in real time so that this information can be easily incorporated in neurofeedback or BCI presentations.

Energy and exergy analysis of the turbo-generators and steam turbine for the main feed water pump drive on LNG carrier

International Nuclear Information System (INIS)

Mrzljak, Vedran; Poljak, Igor; Mrakovčić, Tomislav

2017-01-01

Highlights: • Two low-power steam turbines in the LNG carrier propulsion plant were investigated. • Energy and exergy efficiencies of both steam turbines vary between 46% and 62%. • The ambient temperature has a low impact on exergy efficiency of analyzed turbines. • The maximum efficiencies area of both turbines was investigated. • A method for increasing the turbo-generator efficiencies by 1–3% is presented. - Abstract: Nowadays, marine propulsion systems are mainly based on internal combustion diesel engines. Despite this fact, a number of LNG carriers have steam propulsion plants. In such plants, steam turbines are used not only for ship propulsion, but also for electrical power generation and main feed water pump drive. Marine turbo-generators and steam turbine for the main feed water pump drive were investigated on the analyzed LNG carrier with steam propulsion plant. The measurements of various operating parameters were performed and obtained data were used for energy and exergy analysis. All the measurements and calculations were performed during the ship acceleration. The analysis shows that the energy and exergy efficiencies of both analyzed low-power turbines vary between 46% and 62% what is significantly lower in comparison with the high-power steam turbines. The ambient temperature has a low impact on exergy efficiency of analyzed turbines (change in ambient temperature for 10 °C causes less than 1% change in exergy efficiency). The highest exergy efficiencies were achieved at the lowest observed ambient temperature. Also, the highest efficiencies were achieved at 71.5% of maximum developed turbo-generator power while the highest efficiencies of steam turbine for the main feed water pump drive were achieved at maximum turbine developed power. Replacing the existing steam turbine for the main feed water pump drive with an electric motor would increase the turbo-generator energy and exergy efficiencies for at least 1–3% in all analyzed

Method for transmitting analog data over a fiber-optic link

International Nuclear Information System (INIS)

Dyer, G.R.

1981-01-01

The transmission of high-speed analog dat across an insulating break is a common requirement for present fusion experiments, and it will be a necessity for a reactor-like device. Presently available systems tend to be complex, slow, and expensive. A method is described for implementing a fiber-optic link with analog data input and output. Two realizations of the method are given. A medium-speed system using monolithic circuitry is capable of a dc to 20-KHz bandwidth with excellent linearity and a dynamic range of at least 60 dB. A higher-speed system uses some discrete circuitry to attain a 500-KHz bandwidth with at least a 40-dB dynamic range. Both systems use a relatively inexpensive digital optical link kit combined with a duty cycle modulation scheme for data tramsmission. This method achieves accurate reproduction of complex waveforms without introducing the quantization errors inherent in analog-to-digital conversion, offers bipolar response with low offset and drift, and maintains a constant bandwidth regardless of signal level

Science Teachers' Analogical Reasoning

Science.gov (United States)

Mozzer, Nilmara Braga; Justi, Rosária

2013-08-01

Analogies can play a relevant role in students' learning. However, for the effective use of analogies, teachers should not only have a well-prepared repertoire of validated analogies, which could serve as bridges between the students' prior knowledge and the scientific knowledge they desire them to understand, but also know how to introduce analogies in their lessons. Both aspects have been discussed in the literature in the last few decades. However, almost nothing is known about how teachers draw their own analogies for instructional purposes or, in other words, about how they reason analogically when planning and conducting teaching. This is the focus of this paper. Six secondary teachers were individually interviewed; the aim was to characterize how they perform each of the analogical reasoning subprocesses, as well as to identify their views on analogies and their use in science teaching. The results were analyzed by considering elements of both theories about analogical reasoning: the structural mapping proposed by Gentner and the analogical mechanism described by Vosniadou. A comprehensive discussion of our results makes it evident that teachers' content knowledge on scientific topics and on analogies as well as their pedagogical content knowledge on the use of analogies influence all their analogical reasoning subprocesses. Our results also point to the need for improving teachers' knowledge about analogies and their ability to perform analogical reasoning.

Design and Testing of a Combustor for a Turbo-Ramjet Engine for UAV and Missile Applications

Science.gov (United States)

2003-03-01

CA, September 1999. 6. Al- Namani , S . M., Development of Shrouded Turbojet to Form a Turboramjet for Future Missile Applications, Master’s Thesis...Turbo- ramjet Engine for UAV and Missile Applications 6. AUTHOR( S ) Ross H. Piper III 5. FUNDING NUMBERS 7. PERFORMING ORGANIZATION NAME( S ) AND...ADDRESS(ES) Naval Postgraduate School Monterey, CA 93943-5000 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING / MONITORING AGENCY NAME( S

Optimal properties of analog perceptrons with excitatory weights.

Directory of Open Access Journals (Sweden)

Claudia Clopath

Full Text Available The cerebellum is a brain structure which has been traditionally devoted to supervised learning. According to this theory, plasticity at the Parallel Fiber (PF to Purkinje Cell (PC synapses is guided by the Climbing fibers (CF, which encode an 'error signal'. Purkinje cells have thus been modeled as perceptrons, learning input/output binary associations. At maximal capacity, a perceptron with excitatory weights expresses a large fraction of zero-weight synapses, in agreement with experimental findings. However, numerous experiments indicate that the firing rate of Purkinje cells varies in an analog, not binary, manner. In this paper, we study the perceptron with analog inputs and outputs. We show that the optimal input has a sparse binary distribution, in good agreement with the burst firing of the Granule cells. In addition, we show that the weight distribution consists of a large fraction of silent synapses, as in previously studied binary perceptron models, and as seen experimentally.

Analog synthetic biology.

Science.gov (United States)

Sarpeshkar, R

2014-03-28

We analyse the pros and cons of analog versus digital computation in living cells. Our analysis is based on fundamental laws of noise in gene and protein expression, which set limits on the energy, time, space, molecular count and part-count resources needed to compute at a given level of precision. We conclude that analog computation is significantly more efficient in its use of resources than deterministic digital computation even at relatively high levels of precision in the cell. Based on this analysis, we conclude that synthetic biology must use analog, collective analog, probabilistic and hybrid analog-digital computational approaches; otherwise, even relatively simple synthetic computations in cells such as addition will exceed energy and molecular-count budgets. We present schematics for efficiently representing analog DNA-protein computation in cells. Analog electronic flow in subthreshold transistors and analog molecular flux in chemical reactions obey Boltzmann exponential laws of thermodynamics and are described by astoundingly similar logarithmic electrochemical potentials. Therefore, cytomorphic circuits can help to map circuit designs between electronic and biochemical domains. We review recent work that uses positive-feedback linearization circuits to architect wide-dynamic-range logarithmic analog computation in Escherichia coli using three transcription factors, nearly two orders of magnitude more efficient in parts than prior digital implementations.

Inducibility of error-prone DNA repair in yeast

International Nuclear Information System (INIS)

Siede, W.; Eckardt, F.

1984-01-01

Whereas some experimental evidence suggests that mutagenesis in yeast after treatment with DNA-damaging agents involves inducible functions, a general-acting error-prone repair activity analogous to the SOS system of Escherichia coli has not yet been demonstrated. The current literature on the problem of inducibility of mutagenic repair in yeast is reviewed with emphasis on the differences in the experimental procedures applied. (orig.)

DAT/SERT Selectivity of Flexible GBR 12909 Analogs Modeled Using 3D-QSAR Methods

Science.gov (United States)

Gilbert, Kathleen M.; Boos, Terrence L.; Dersch, Christina M.; Greiner, Elisabeth; Jacobson, Arthur E.; Lewis, David; Matecka, Dorota; Prisinzano, Thomas E.; Zhang, Ying; Rothman, Richard B.; Rice, Kenner C.; Venanzi, Carol A.

2007-01-01

The dopamine reuptake inhibitor GBR 12909 (1-{2-[bis(4-fluorophenyl)methoxy]ethyl}-4-(3-phenylpropyl)piperazine, 1) and its analogs have been developed as tools to test the hypothesis that selective dopamine transporter (DAT) inhibitors will be useful therapeutics for cocaine addiction. This 3D-QSAR study focuses on the effect of substitutions in the phenylpropyl region of 1. CoMFA and CoMSIA techniques were used to determine a predictive and stable model for the DAT/serotonin transporter (SERT) selectivity (represented by pKi (DAT/SERT)) of a set of flexible analogs of 1, most of which have eight rotatable bonds. In the absence of a rigid analog to use as a 3D-QSAR template, six conformational families of analogs were constructed from six pairs of piperazine and piperidine template conformers identified by hierarchical clustering as representative molecular conformations. Three models stable to y-value scrambling were identified after a comprehensive CoMFA and CoMSIA survey with Region Focusing. Test set correlation validation led to an acceptable model, with q2 = 0.508, standard error of prediction = 0.601, two components, r2 = 0.685, standard error of estimate = 0.481, F value = 39, percent steric contribution = 65, and percent electrostatic contribution = 35. A CoMFA contour map identified areas of the molecule that affect pKi (DAT/SERT). This work outlines a protocol for deriving a stable and predictive model of the biological activity of a set of very flexible molecules. PMID:17127069

Effect of turbo charging and steam injection methods on the performance of a Miller cycle diesel engine (MCDE)

International Nuclear Information System (INIS)

Gonca, Guven; Sahin, Bahri

2017-01-01

Highlights: • Performance of a diesel engine is simulated by finite time thermodynamics. • Effect of steam injection on performance of a Miller cycle engine is examined. • Model results are verified with the experimental data with less than 7% error. - Abstract: In this study, application of the steam injection method (SIM), Miller cycle (MC) and turbo charging (TC) techniques into a four stroke, direct-injection diesel engine has been numerically and empirically conducted. NOx emissions have detrimental influences on the environment and living beings. They are formed at the high temperatures, thus the Diesel engines are serious NOx generation sources since they have higher compression ratios and higher combustion temperatures. The international regulations have decreased the emission limits due to environmental reasons. The Miller cycle (MC) application and steam injection method (SIM) have been popular to abate NOx produced from the internal combustion engines (ICEs), in the recent years. However, the MC application can cause a reduction in power output. The most known technique which maximizes the engine power and abates exhaust emissions is TC. Therefore, if these three techniques are combined, the power loss can be tolerated and pollutant emissions can be minimized. While the application of the MC and SIM causes to diminish in the brake power and brake thermal efficiency of the engine up to 6.5% and 10%, the TC increases the brake power and brake thermal efficiency of the engine up to 18% and 12%. The experimental and theoretical results have been compared in terms of the torque, the specific fuel consumption (SFC), the brake power and the brake thermal efficiency. The results acquired from theoretical modeling have been validated with empirical data with less than 7% maximum error. The results showed that developed combination can increase the engine performance and the method can be easily applied to the Diesel engines.

Statics of loose triangular embankment under Nadai’s sand hill analogy

Science.gov (United States)

Pipatpongsa, Thirapong; Heng, Sokbil; Iizuka, Atsushi; Ohta, Hideki

2010-10-01

In structural mechanics, Nadai's sand hill analogy is the interpretation of an ultimate torque applied to a given structural member with a magnitude that is analogously twice the volume of stable sand heap which can be accommodated on a transverse cross-section basis. Nadai's analogy is accompanied by his observation of a loose triangular embankment, based on the fact that gravitating loose earth is stable if inclined just under the angle of repose. However, Nadai's analysis of stress distribution in a planar sand heap was found to be inaccurate because the total pressure obtained from Nadai's solution is greater than the self-weight calculated from the heap geometry. This raises a question about the validity of his observation in relation to the analogy. To confirm his criterion, this article presents and corrects the error found in Nadai's solution by analyzing a radially symmetric stress field for a wedge-shaped sand heap with the purpose of satisfying both force balance and Nadai's closure. The fundamental equation was obtained by letting the friction state vary as a function of angular position and deduce it under the constraint that the principal stress orientation obeys Nadai's closure. The theoretical solution sufficiently agreed with the past experimental measurements.

Digitization errors using digital charge division positionsensitive detectors

International Nuclear Information System (INIS)

Berliner, R.; Mildner, D.F.R.; Pringle, O.A.

1981-01-01

The data acquisition speed and electronic stability of a charge division position-sensitive detector may be improved by using digital signal processing with a table look-up high speed multiply to form the charge division quotient. This digitization process introduces a positional quantization difficulty which reduces the detector position sensitivity. The degree of the digitization error is dependent on the pulse height spectrum of the detector and on the resolution or dynamic range of the system analog-to-digital converters. The effects have been investigated analytically and by computer simulation. The optimum algorithm for position sensing determination using 8-bit digitization and arithmetic has a digitization error of less than 1%. (orig.)

BER performance comparison of optical CDMA systems with/without turbo codes

Science.gov (United States)

Kulkarni, Muralidhar; Chauhan, Vijender S.; Dutta, Yashpal; Sinha, Ravindra K.

2002-08-01

In this paper, we have analyzed and simulated the BER performance of a turbo coded optical code-division multiple-access (TC-OCDMA) system. A performance comparison has been made between uncoded OCDMA and TC-OCDMA systems employing various OCDMA address codes (optical orthogonal codes (OOCs), Generalized Multiwavelength Prime codes (GMWPC's), and Generalized Multiwavelength Reed Solomon code (GMWRSC's)). The BER performance of TC-OCDMA systems has been analyzed and simulated by varying the code weight of address code employed by the system. From the simulation results, it is observed that lower weight address codes can be employed for TC-OCDMA systems that can have the equivalent BER performance of uncoded systems employing higher weight address codes for a fixed number of active users.

Biomedical sensor design using analog compressed sensing

Science.gov (United States)

Balouchestani, Mohammadreza; Krishnan, Sridhar

2015-05-01

The main drawback of current healthcare systems is the location-specific nature of the system due to the use of fixed/wired biomedical sensors. Since biomedical sensors are usually driven by a battery, power consumption is the most important factor determining the life of a biomedical sensor. They are also restricted by size, cost, and transmission capacity. Therefore, it is important to reduce the load of sampling by merging the sampling and compression steps to reduce the storage usage, transmission times, and power consumption in order to expand the current healthcare systems to Wireless Healthcare Systems (WHSs). In this work, we present an implementation of a low-power biomedical sensor using analog Compressed Sensing (CS) framework for sparse biomedical signals that addresses both the energy and telemetry bandwidth constraints of wearable and wireless Body-Area Networks (BANs). This architecture enables continuous data acquisition and compression of biomedical signals that are suitable for a variety of diagnostic and treatment purposes. At the transmitter side, an analog-CS framework is applied at the sensing step before Analog to Digital Converter (ADC) in order to generate the compressed version of the input analog bio-signal. At the receiver side, a reconstruction algorithm based on Restricted Isometry Property (RIP) condition is applied in order to reconstruct the original bio-signals form the compressed bio-signals with high probability and enough accuracy. We examine the proposed algorithm with healthy and neuropathy surface Electromyography (sEMG) signals. The proposed algorithm achieves a good level for Average Recognition Rate (ARR) at 93% and reconstruction accuracy at 98.9%. In addition, The proposed architecture reduces total computation time from 32 to 11.5 seconds at sampling-rate=29 % of Nyquist rate, Percentage Residual Difference (PRD)=26 %, Root Mean Squared Error (RMSE)=3 %.

Error analysis in predictive modelling demonstrated on mould data.

Science.gov (United States)

Baranyi, József; Csernus, Olívia; Beczner, Judit

2014-01-17

The purpose of this paper was to develop a predictive model for the effect of temperature and water activity on the growth rate of Aspergillus niger and to determine the sources of the error when the model is used for prediction. Parallel mould growth curves, derived from the same spore batch, were generated and fitted to determine their growth rate. The variances of replicate ln(growth-rate) estimates were used to quantify the experimental variability, inherent to the method of determining the growth rate. The environmental variability was quantified by the variance of the respective means of replicates. The idea is analogous to the "within group" and "between groups" variability concepts of ANOVA procedures. A (secondary) model, with temperature and water activity as explanatory variables, was fitted to the natural logarithm of the growth rates determined by the primary model. The model error and the experimental and environmental errors were ranked according to their contribution to the total error of prediction. Our method can readily be applied to analysing the error structure of predictive models of bacterial growth models, too. © 2013.

An Iterative Multiuser Detector for Turbo-Coded DS-CDMA Systems

Directory of Open Access Journals (Sweden)

Takawira Fambirai

2005-01-01

Full Text Available We propose an iterative multiuser detector for turbo-coded synchronous and asynchronous direct-sequence CDMA (DS-CDMA systems. The receiver is derived from the maximum a posteriori (MAP estimation of the single user's transmitted data, conditioned on information about the estimate of the multiple-access interference (MAI and the received signal from the channel. This multiple-access interference is reconstructed by making hard decisions on the users' detected bits at the preceding iteration. The complexity of the proposed receiver increases linearly with the number of users. The proposed detection scheme is compared with a previously developed one. The multiuser detector proposed in this paper has a better performance when the transmitted powers of all active users are equal in the additive white Gaussian noise (AWGN channel. Also, the detector is found to be resilient against the near-far effect.

Rhetoric and analogies

OpenAIRE

Aragonès, Enriqueta; Gilboa, Itzhak; Postlewaite, Andrew; Schmeidler, David; Universitat Autònoma de Barcelona. Unitat de Fonaments de l'Anàlisi Econòmica; Universitat Autònoma de Barcelona. Institut d'Anàlisi Econòmica

2013-01-01

The art of rhetoric may be defined as changing other people's minds (opinions, beliefs) without providing them new information. One tech- nique heavily used by rhetoric employs analogies. Using analogies, one may draw the listener's attention to similarities between cases and to re-organize existing information in a way that highlights certain reg- ularities. In this paper we offer two models of analogies, discuss their theoretical equivalence, and show that finding good analogies is a com- p...

TURBO: a computer program for two-dimensional incompressible fluid flow analysis using a two-equations turbulence model

International Nuclear Information System (INIS)

Botelho, D.A.; Moreira, M.L.

1991-06-01

The Reynolds turbulent transport equations for an incompressible fluid are integrated on a bi-dimensional staggered grid, for velocity and pressure, using the SIMPLER method. With the resulting algebraic relations it was developed the TURBO program, which final objectives are the thermal stratification and natural convection analysis of nuclear reactor pools. This program was tested in problems applications with analytic or experimental solutions previously known. (author)

Turbo-Proton Echo Planar Spectroscopic Imaging (t-PEPSI) MR technique in the detection of diffuse axonal damage in brain injury. Comparison with Gradient-Recalled Echo (GRE) sequence.

Science.gov (United States)

Giugni, E; Sabatini, U; Hagberg, G E; Formisano, R; Castriota-Scanderbeg, A

2005-01-01

Diffuse axonal injury (DAI) is a common type of primary neuronal injury in patients with severe traumatic brain injury, and is frequently accompanied by tissue tear haemorrhage. The T2*-weighted gradient-recalled echo (GRE) sequences are more sensitive than T2-weighted spin-echo images for detection of haemorrhage. This study was undertaken to determine whether turbo-PEPSI, an extremely fast multi-echo-planar-imaging sequence, can be used as an alternative to the GRE sequence for detection of DAI. Nineteen patients (mean age 24,5 year) with severe traumatic brain injury (TBI), occurred at least 3 months earlier, underwent a brain MRI study on a 1.5-Tesla scanner. A qualitative evaluation of the turbo-PEPSI sequences was performed by identifying the optimal echo time and in-plane resolution. The number and size of DAI lesions, as well as the signal intensity contrast ratio (SI CR), were computed for each set of GRE and turbo-PEPSI images, and divided according to their anatomic location into lobar and/or deep brain. There was no significant difference between GRE and turbo-PEPSI sequences in the total number of DAI lesions detected (283 vs 225 lesions, respectively). The GRE sequence identified a greater number of hypointense lesions in the temporal lobe compared to the t-PEPSI sequence (72 vs 35, pPEPSI than for the GRE sequence (pPEPSI sequence can be used as an alternative to the GRE to assess brain DAI in severe TBI patients, especially if uncooperative and medically unstable.

Intuitive analog circuit design

CERN Document Server

Thompson, Marc

2013-01-01

Intuitive Analog Circuit Design outlines ways of thinking about analog circuits and systems that let you develop a feel for what a good, working analog circuit design should be. This book reflects author Marc Thompson's 30 years of experience designing analog and power electronics circuits and teaching graduate-level analog circuit design, and is the ideal reference for anyone who needs a straightforward introduction to the subject. In this book, Dr. Thompson describes intuitive and ""back-of-the-envelope"" techniques for designing and analyzing analog circuits, including transistor amplifi

Turbo Pascal Computer Code for PIXE Analysis

International Nuclear Information System (INIS)

Darsono

2002-01-01

To optimal utilization of the 150 kV ion accelerator facilities and to govern the analysis technique using ion accelerator, the research and development of low energy PIXE technology has been done. The R and D for hardware of the low energy PIXE installation in P3TM have been carried on since year 2000. To support the R and D of PIXE accelerator facilities in harmonize with the R and D of the PIXE hardware, the development of PIXE software for analysis is also needed. The development of database of PIXE software for analysis using turbo Pascal computer code is reported in this paper. This computer code computes the ionization cross-section, the fluorescence yield, and the stopping power of elements also it computes the coefficient attenuation of X- rays energy. The computer code is named PIXEDASIS and it is part of big computer code planed for PIXE analysis that will be constructed in the near future. PIXEDASIS is designed to be communicative with the user. It has the input from the keyboard. The output shows in the PC monitor, which also can be printed. The performance test of the PIXEDASIS shows that it can be operated well and it can provide data agreement with data form other literatures. (author)

Order of 4 November 1988 on treatment by ionizing radiation of rice flour and its products obtained by turbo-separation

International Nuclear Information System (INIS)

1988-01-01

This Order fixes the conditions for the sale of rice flour and products obtained from its turbo-separation whose microbial decontamination was obtained through exposure to cobalt 60 or cesium 137 gamma-rays or accelerated electron beams with an energy below or equal to 10 Mev. (NEA) [fr

Design of a 12-bit 80-MS/s CMOS digital-to-analog converter for PLC-VDSL applications

Science.gov (United States)

Ruiz-Amaya, Jesus; Delgado-Restituto, Manuel; Fernandez-Bootello, J. Francisco; de la Rosa, Jose M.

2005-06-01

This paper describes the design of a 12-bit 80MS/s Digital-to-Analog converter implemented in 0.13mm CMOS logic technology. The design has been computer-aided by a developed toolbox for the simulation and verification of Nyquist-Rate Analog-to-Digital and Digital-to-Analog converters in MATLAB. The embedded simulator uses SIMULINK C-coded S-functions to model all required subcircuits including their main error mechanisms. This approach allows to drastically speed up the simulation CPU-time and makes the proposed tool an advantageous alternative for fast exploration of requirements and as a design validation tool. The converter is segmented in a unary current-cell matrix for 8 MSB's and a binary-weighted array for 4 LSB's. Current sources of the converter are laid out separately from current-cell switching matrix core block and distribute in double centroid to reduce random errors and transient noise coupling. The linearity errors caused by remaining gradient errors are reduced by a modified Q2 Random-Walk switching sequence. Simulation results show that the Spurious-Free Dynamic-Range is better than 58.5dB up to 80MS/s. The estimated Signal-to-Noise Distortion Ratio yield is 99.7% and it is supposed to be better than 58dB from DC to Nyquist frequency. Multi-Tone Power Ratio is higher 59dB for several DMT test signals. The converter dissipates less than 129mW from a 3.3V supply and occupies less than 1.7mm2 die area. The results have been checked with all process corners from -40° to 85° and power supply from 3V to 3.6V.

Isotropic resolution diffusion tensor imaging of lumbosacral and sciatic nerves using a phase-corrected diffusion-prepared 3D turbo spin echo.

Science.gov (United States)

Cervantes, Barbara; Van, Anh T; Weidlich, Dominik; Kooijman, Hendrick; Hock, Andreas; Rummeny, Ernst J; Gersing, Alexandra; Kirschke, Jan S; Karampinos, Dimitrios C

2018-08-01

To perform in vivo isotropic-resolution diffusion tensor imaging (DTI) of lumbosacral and sciatic nerves with a phase-navigated diffusion-prepared (DP) 3D turbo spin echo (TSE) acquisition and modified reconstruction incorporating intershot phase-error correction and to investigate the improvement on image quality and diffusion quantification with the proposed phase correction. Phase-navigated DP 3D TSE included magnitude stabilizers to minimize motion and eddy-current effects on the signal magnitude. Phase navigation of motion-induced phase errors was introduced before readout in 3D TSE. DTI of lower back nerves was performed in vivo using 3D TSE and single-shot echo planar imaging (ss-EPI) in 13 subjects. Diffusion data were phase-corrected per k z plane with respect to T 2 -weighted data. The effects of motion-induced phase errors on DTI quantification was assessed for 3D TSE and compared with ss-EPI. Non-phase-corrected 3D TSE resulted in artifacts in diffusion-weighted images and overestimated DTI parameters in the sciatic nerve (mean diffusivity [MD] = 2.06 ± 0.45). Phase correction of 3D TSE DTI data resulted in reductions in all DTI parameters (MD = 1.73 ± 0.26) of statistical significance (P ≤ 0.001) and in closer agreement with ss-EPI DTI parameters (MD = 1.62 ± 0.21). DP 3D TSE with phase correction allows distortion-free isotropic diffusion imaging of lower back nerves with robustness to motion-induced artifacts and DTI quantification errors. Magn Reson Med 80:609-618, 2018. © 2018 The Authors Magnetic Resonance in Medicine published by Wiley Periodicals, Inc. on behalf of International Society for Magnetic Resonance in Medicine. This is an open access article under the terms of the Creative Commons Attribution NonCommercial License, which permits use, distribution and reproduction in any medium, provided the original work is properly cited and is not used for commercial purposes. © 2018 The Authors Magnetic Resonance

40 years of Porsche turbo engines. The basis for future innovations; 40 Jahre Porsche Turbomotoren. Basis fuer zukuenftige Innovationen

Energy Technology Data Exchange (ETDEWEB)

Neusser, Heinz-Jakob; Kerkau, Martin; Schwarzenthal, Dietmar; Hemmerlein, Norbert [Dr. Ing. h.c. F. Porsche AG, Weissach (Germany)

2011-07-01

Porsche has been developing turbocharged gasoline engines for road and race vehicles for more than 40 years. Many significant innovations in turbocharging technology have been realised in the development history of the 911 Turbo in particular. With its downsizing concept, this engine remains synonymous with high performance in combination with incomparable fuel efficiency among high performance cars. The basis for future engine concepts with reduced fuel consumption lies in a combination of turbocharging with a reduction in engine displacement and number of cylinders. All necessary and innovative technologies such as Variable Turbine Geometry (VTG), Direct Fuel Injection (DFI) and the variable valve timing system VarioCam Plus {sup registered} are already realised in Porsche production engines and impressively demonstrate the potential of modern turbo engines. The light TiAl turbine wheel that will be implemented in the Porsche Panamera represents the latest innovation for further improvement in the throttle response. This set of technologies makes it possible to solve the conflict of goals between high performance and low fuel consumption. (orig.)

High-speed and high-resolution analog-to-digital and digital-to-analog converters

NARCIS (Netherlands)

van de Plassche, R.J.

1989-01-01

Analog-to-digital and digital-to-analog converters are important building blocks connecting the analog world of transducers with the digital world of computing, signal processing and data acquisition systems. In chapter two the converter as part of a system is described. Requirements of analog

Ber analysis of iterative turbo encoded miso wireless communication system under implementation of q-ostbc scheme

OpenAIRE

Kabir, M. Hasnat; Ullah, Shaikh Enayet; Zaman, Mustari; Rashed, Md. Golam

2012-01-01

In this paper, a comprehensive study has been made to evaluate the performance of a MISO wireless communication system. The 4-by-1 spatially multiplexed Turbo encoded system under investigation incorporates Quasi-orthogonal space-time block coding (Q-STBC) and ML signal detection schemes under QPSK, QAM, 16PSK and 16QAM digital modulations. The simulation results elucidate that a significant improvement of system performance is achieved in QAM modulation. The results are also indicative of no...

Advantages of variable-speed operation of hydraulic turbo-engines; Vorteile durch den drehzahlvariablen Betrieb von hydraulischen Stroemungsmaschinen

Energy Technology Data Exchange (ETDEWEB)

Harbort, T. [Stuttgart Univ. (Germany). Inst. fuer Stroemungsmechanik und Hydraulische Stroemungsmaschinen

1997-12-31

The performance of current hydraulic turbo-engines in the variable speed sector is monitored and judged. The study covers radial and axial engines as well as Pelton turbines. Variable-speed operation of hydraulic turbo-engines can be realized by means of different combinations of electrical rotating machines and frequency converters. The operating range of the frequency converter plays an important role in the optimization of performance and is taken into account. The smoothness of run of reaction turbines and their cavitation performance can be enhanced by speed regulation. But above all, efficiency is more or less substantially enhanced during partial load or in the case of greatly varying heights of drop. The latter holds true also of Pelton turbines. (orig.) [Deutsch] Das Betriebsverhalten der gaengigen hydraulischen Stroemungsmaschinen wird in Hinblick auf den drehzahlvariablen Betrieb erfasst und beurteilt. Die Untersuchung erfolgt fuer Radialmaschinen, Axialmaschinen und Peltonturbinen. Der drehzahlvariable Betrieb hydraulischer Stroemungsmaschinen kann mit verschiedenen Kombinationen von elektrischen Maschinen und Frequenzumrichtern realisiert werden. Der Arbeitsbereich des Frequenzumrichters spielt eine wichtige Rolle fuer die Optimierung des Betriebsverhaltens und wird beruecksichtigt. Bei Ueberdruckturbinen kann man durch Drehzahlregelung eine groessere Laufruhe sowie ein guenstigeres Kavitationsverhalten erreichen. Vor allem aber sind im Teillastbereich oder bei stark schwankenden Fallhoehen mehr oder weniger grosse Wirkungsgradgewinne erzielbar. Das letztere gilt auch fuer Peltonturbinen. (orig.)

Design and Prototyping Flow of Flexible and Efficient NISC-Based Architectures for MIMO Turbo Equalization and Demapping

Directory of Open Access Journals (Sweden)

Mostafa Rizk

2016-08-01

Full Text Available In the domain of digital wireless communication, flexible design implementations are increasingly explored for different applications in order to cope with diverse system configurations imposed by the emerging wireless communication standards. In fact, shrinking the design time to meet market pressure, on the one hand, and adding the emerging flexibility requirement and, hence, increasing system complexity, on the other hand, require a productive design approach that also ensures final design quality. The no instruction set computer (NISC approach fulfills these design requirements by eliminating the instruction set overhead. The approach offers static scheduling of the datapath, automated register transfer language (RTLsynthesis and allows the designer to have direct control of hardware resources. This paper presents a complete NISC-based design and prototype flow, from architecture specification till FPGA implementation. The proposed design and prototype flow is illustrated through two case studies of flexible implementations, which are dedicated to low-complexity MIMO turbo-equalizer and a universal turbo-demapper. Moreover, the flexibility of the proposed prototypes allows supporting all communication modes defined in the emerging wireless communication standards, such LTE, LTE-Advanced, WiMAX, WiFi and DVB-RCS. For each prototype, its functionality is evaluated, and the resultant performance is verified for all system configurations.

New Turbo Compound Systems in Automotive Industry for Internal Combustion Engine to Recover Energy

Science.gov (United States)

Chiriac, R.; Chiru, A.; Condrea, O.

2017-10-01

The large amount of heat is scattered in the internal combustion engine through exhaust gas, coolant, convective and radiant heat transfer. Of all these residual heat sources, exhaust gases have the potential to recover using various modern heat recovery techniques. Waste heat recovery from an engine could directly reduce fuel consumption, increase available electrical power and improve overall system efficiency and if it would be used a turbochargers that can also produce energy. This solution is called turbo aggregation and has other ways to develop it in other areas of research like the electrical field. [1-3

Structured Analog CMOS Design

CERN Document Server

Stefanovic, Danica

2008-01-01

Structured Analog CMOS Design describes a structured analog design approach that makes it possible to simplify complex analog design problems and develop a design strategy that can be used for the design of large number of analog cells. It intentionally avoids treating the analog design as a mathematical problem, developing a design procedure based on the understanding of device physics and approximations that give insight into parameter interdependences. The proposed transistor-level design procedure is based on the EKV modeling approach and relies on the device inversion level as a fundament

Analog and hybrid computing

CERN Document Server

Hyndman, D E

2013-01-01

Analog and Hybrid Computing focuses on the operations of analog and hybrid computers. The book first outlines the history of computing devices that influenced the creation of analog and digital computers. The types of problems to be solved on computers, computing systems, and digital computers are discussed. The text looks at the theory and operation of electronic analog computers, including linear and non-linear computing units and use of analog computers as operational amplifiers. The monograph examines the preparation of problems to be deciphered on computers. Flow diagrams, methods of ampl

Over-Sampling Codebook-Based Hybrid Minimum Sum-Mean-Square-Error Precoding for Millimeter-Wave 3D-MIMO

KAUST Repository

Mao, Jiening

2018-05-23

Abstract: Hybrid precoding design is challenging for millimeter-wave (mmWave) massive MIMO. Most prior hybrid precoding schemes are designed to maximize the sum spectral efficiency (SSE), while seldom investigate the bit-error-rate (BER). Therefore, this letter designs an over-sampling codebook (OSC)-based hybrid minimum sum-mean-square-error (min-SMSE) precoding to optimize the BER. Specifically, given the effective baseband channel consisting of the real channel and analog precoding, we first design the digital precoder/combiner based on min-SMSE criterion to optimize the BER. To further reduce the SMSE between the transmit and receive signals, we propose an OSC-based joint analog precoder/combiner (JAPC) design. Simulation results show that the proposed scheme can achieve the better performance than its conventional counterparts.

Over-Sampling Codebook-Based Hybrid Minimum Sum-Mean-Square-Error Precoding for Millimeter-Wave 3D-MIMO

KAUST Repository

Mao, Jiening; Gao, Zhen; Wu, Yongpeng; Alouini, Mohamed-Slim

2018-01-01

Hybrid precoding design is challenging for millimeter-wave (mmWave) massive MIMO. Most prior hybrid precoding schemes are designed to maximize the sum spectral efficiency (SSE), while seldom investigate the bit-error-rate (BER). Therefore, this letter designs an over-sampling codebook (OSC)-based hybrid minimum sum-mean-square-error (min-SMSE) precoding to optimize the BER. Specifically, given the effective baseband channel consisting of the real channel and analog precoding, we first design the digital precoder/combiner based on min-SMSE criterion to optimize the BER. To further reduce the SMSE between the transmit and receive signals, we propose an OSC-based joint analog precoder/combiner (JAPC) design. Simulation results show that the proposed scheme can achieve the better performance than its conventional counterparts.

The baby and the bath water: improving metaphors and analogies in high school biology texts

Science.gov (United States)

Shors, Luke

This dissertation is concerned with understanding how metaphors and analogies function in biology education and whether some of the philosophical critiques of the language used in the field of biology -- and in particular its accompanying metaphors and analogies, have a basis in the educational materials used to teach the subject. This inquiry was carried out through examining the pedagogical features and content of metaphors and analogies from three high school biology textbooks. After identifying over two hundred and twenty-five verbal and pictorial metaphors and analogies, these figures of speech were coded based on prior research that establishes effective characteristics for their use. In tandem with this quantitative analysis, a philosophical analysis considers how well the content of these metaphors and analogies aligns with current scientific understanding and what misunderstandings may be engendered through the use of these metaphors and analogies. The major findings of the analysis include: 1) Textbook authors are much more likely to utilize metaphors and analogies as well as signal their presence to students compared with past analyses; 2) A number of metaphors and analogies either contain errors in analogical mapping or use source analogues that are too antiquated to support today's students; 3) The content of many metaphors and analogies is frequently outdated in reference to current scientific understanding; and 4) Many metaphors and analogies tend to reinforce tacit elements of past scientific paradigms - these are termed 'reinforcing metaphors' in the dissertation and include nature as machine, nature as blueprint or information, nature as business and nature as war. The present work submits several implications for students learning biology as well as the manner in which students come to understand the natural world. The work suggests ways to reduce ineffective metaphors and analogies as well as reliance on reinforcing metaphors. It offers new

Analog-to-digital conversion

CERN Document Server

Pelgrom, Marcel J M

2010-01-01

The design of an analog-to-digital converter or digital-to-analog converter is one of the most fascinating tasks in micro-electronics. In a converter the analog world with all its intricacies meets the realm of the formal digital abstraction. Both disciplines must be understood for an optimum conversion solution. In a converter also system challenges meet technology opportunities. Modern systems rely on analog-to-digital converters as an essential part of the complex chain to access the physical world. And processors need the ultimate performance of digital-to-analog converters to present the results of their complex algorithms. The same progress in CMOS technology that enables these VLSI digital systems creates new challenges for analog-to-digital converters: lower signal swings, less power and variability issues. Last but not least, the analog-to-digital converter must follow the cost reduction trend. These changing boundary conditions require micro-electronics engineers to consider their design choices for...

On the mean squared error of the ridge estimator of the covariance and precision matrix

NARCIS (Netherlands)

van Wieringen, Wessel N.

2017-01-01

For a suitably chosen ridge penalty parameter, the ridge regression estimator uniformly dominates the maximum likelihood regression estimator in terms of the mean squared error. Analogous results for the ridge maximum likelihood estimators of covariance and precision matrix are presented.

Analysis of Medication Errors in Simulated Pediatric Resuscitation by Residents

Directory of Open Access Journals (Sweden)

Evelyn Porter

2014-07-01

Full Text Available Introduction: The objective of our study was to estimate the incidence of prescribing medication errors specifically made by a trainee and identify factors associated with these errors during the simulated resuscitation of a critically ill child. Methods: The results of the simulated resuscitation are described. We analyzed data from the simulated resuscitation for the occurrence of a prescribing medication error. We compared univariate analysis of each variable to medication error rate and performed a separate multiple logistic regression analysis on the significant univariate variables to assess the association between the selected variables. Results: We reviewed 49 simulated resuscitations . The final medication error rate for the simulation was 26.5% (95% CI 13.7% - 39.3%. On univariate analysis, statistically significant findings for decreased prescribing medication error rates included senior residents in charge, presence of a pharmacist, sleeping greater than 8 hours prior to the simulation, and a visual analog scale score showing more confidence in caring for critically ill children. Multiple logistic regression analysis using the above significant variables showed only the presence of a pharmacist to remain significantly associated with decreased medication error, odds ratio of 0.09 (95% CI 0.01 - 0.64. Conclusion: Our results indicate that the presence of a clinical pharmacist during the resuscitation of a critically ill child reduces the medication errors made by resident physician trainees.

Analog earthquakes

International Nuclear Information System (INIS)

Hofmann, R.B.

1995-01-01

Analogs are used to understand complex or poorly understood phenomena for which little data may be available at the actual repository site. Earthquakes are complex phenomena, and they can have a large number of effects on the natural system, as well as on engineered structures. Instrumental data close to the source of large earthquakes are rarely obtained. The rare events for which measurements are available may be used, with modfications, as analogs for potential large earthquakes at sites where no earthquake data are available. In the following, several examples of nuclear reactor and liquified natural gas facility siting are discussed. A potential use of analog earthquakes is proposed for a high-level nuclear waste (HLW) repository

Effects of digital human-machine interface characteristics on human error in nuclear power plants

International Nuclear Information System (INIS)

Li Pengcheng; Zhang Li; Dai Licao; Huang Weigang

2011-01-01

In order to identify the effects of digital human-machine interface characteristics on human error in nuclear power plants, the new characteristics of digital human-machine interface are identified by comparing with the traditional analog control systems in the aspects of the information display, user interface interaction and management, control systems, alarm systems and procedures system, and the negative effects of digital human-machine interface characteristics on human error are identified by field research and interviewing with operators such as increased cognitive load and workload, mode confusion, loss of situation awareness. As to the adverse effects related above, the corresponding prevention and control measures of human errors are provided to support the prevention and minimization of human errors and the optimization of human-machine interface design. (authors)

Quality assessment of the digitalization process of analog x-ray images

International Nuclear Information System (INIS)

Georgieva, D.

2014-01-01

Computer-assisted diagnosis enabled doctors for a second point-of-view on the test results. This improves the diseases' early detection and significantly reduces the chance of errors. These methods very nicely complemented the possibilities of digital medical imaging apparatus, but in analog images their applicability and results entirely depend on the quality of analog images digitalisation. Today many standards and remarks for good practices discuss the digital apparatus image quality but the digitalisation process of analog medical images is not a part of them. Medical imaging apparatus have become digital, but within an entirely digital medical environment is necessary for their ability to blend with the old analog medical imaging carriers. The life of patients doesn't start with the beginning of digital era and for the aim of tracking diseases it is necessary to use the new digital images as well as older analog ones. For the generation of 40-50 years a large archive of images is piled up, which should be accounted of in the diagnosis process. This article is the author's study of the digitalized image quality problem. It offers a new approach to the x-ray image digitalisation - getting the HDR-image by optical sensor. After the HDR-image generation method offers to be used a digital signal processing to improve the quality of the final 16 bit gray scale medical image. The new method for medical image enhancement is proposed - it improves the image contrast, it increases or preserves the dynamic range and it doesn't lead to the loss of small low contrast structures in the image. Key words: Quality of Digital X-Rays Images

Links between N-modular redundancy and the theory of error-correcting codes

Science.gov (United States)

Bobin, V.; Whitaker, S.; Maki, G.

1992-01-01

N-Modular Redundancy (NMR) is one of the best known fault tolerance techniques. Replication of a module to achieve fault tolerance is in some ways analogous to the use of a repetition code where an information symbol is replicated as parity symbols in a codeword. Linear Error-Correcting Codes (ECC) use linear combinations of information symbols as parity symbols which are used to generate syndromes for error patterns. These observations indicate links between the theory of ECC and the use of hardware redundancy for fault tolerance. In this paper, we explore some of these links and show examples of NMR systems where identification of good and failed elements is accomplished in a manner similar to error correction using linear ECC's.

Error of quantum-logic simulation via vector-soliton collisions

International Nuclear Information System (INIS)

Janutka, Andrzej

2007-01-01

In a concept of simulating the quantum logic with vector solitons by the author (Janutka 2006 J. Phys. A: Math. Gen. 39 12505), the soliton polarization is thought of as a state vector of a system of cebits (classical counterparts of qubits) switched via collisions with other solitons. The advantage of this method of information processing compared to schemes using linear optics is the possibility of the determination of the information-register state in a single measurement. Minimization of the information-processing error for different optical realizations of the logical systems is studied in the framework of a quantum analysis of soliton fluctuations. The problem is considered with relevance to general difficulties of the quantum error-correction schemes for the classical analogies of the quantum-information processing

Analog circuit design

CERN Document Server

Dobkin, Bob

2012-01-01

Analog circuit and system design today is more essential than ever before. With the growth of digital systems, wireless communications, complex industrial and automotive systems, designers are being challenged to develop sophisticated analog solutions. This comprehensive source book of circuit design solutions aids engineers with elegant and practical design techniques that focus on common analog challenges. The book's in-depth application examples provide insight into circuit design and application solutions that you can apply in today's demanding designs. <

Optical analogy. Synthesis report

International Nuclear Information System (INIS)

1965-01-01

The authors report the study of conditions under which light attenuation (reflection, diffusion, absorption) and the attenuation of some radiations (notably thermal neutrons) can be described with analogical calculations. The analogy between light physical properties and neutron properties is not searched for, but the analogy between their attenuation characteristics. After having discussed this possible analogy, they propose a mathematical formulation of neutron and optical phenomena which could theoretically justify the optical analogy. The second part reports a more practical study of optics problems such as the study of simple optics materials and illumination measurements, or more precisely the study of angular distributions of optical reflections, a determination of such angular distributions, and an experimental determination of the albedo

The Evidence of Imposex in Turbo sp. from Ujungpiring Waters of Jepara

Science.gov (United States)

Nuraini, RAT; Hartati, R.; Endrawati, H.; Widianingsih; Rachma, MJ; Mahendrajaya, RT

2018-02-01

Imposex is an endocrine disruption syndrome, in which females of marine gastropods develop sexual characteristics of males (penis and/or vas deferens). This syndrome is caused by tributyltin (TBT) or triphenyltin (TPT), toxic organotin compounds found in naval paints used as antifouling system in boats and artificial structures. The main objective of this study was to assess the incidence and severity of imposex in Turbosp.A hundred individus of Turbo sp was collected from Ujung Piring waters of Jepara, and observed for their sex and imposex. The results showed that the ratio male and female was 1.13 : 1, and the frequency of imposex females was 64.58%. The relative penis size were longer in imposex female than in male. The possibility of pollution was clearly shown from high evidence of imposex female.

Evaluation of large girth LDPC codes for PMD compensation by turbo equalization.

Science.gov (United States)

Minkov, Lyubomir L; Djordjevic, Ivan B; Xu, Lei; Wang, Ting; Kueppers, Franko

2008-08-18

Large-girth quasi-cyclic LDPC codes have been experimentally evaluated for use in PMD compensation by turbo equalization for a 10 Gb/s NRZ optical transmission system, and observing one sample per bit. Net effective coding gain improvement for girth-10, rate 0.906 code of length 11936 over maximum a posteriori probability (MAP) detector for differential group delay of 125 ps is 6.25 dB at BER of 10(-6). Girth-10 LDPC code of rate 0.8 outperforms the girth-10 code of rate 0.906 by 2.75 dB, and provides the net effective coding gain improvement of 9 dB at the same BER. It is experimentally determined that girth-10 LDPC codes of length around 15000 approach channel capacity limit within 1.25 dB.

Are all analogies created equal? Prefrontal cortical functioning may predict types of analogical reasoning.

Science.gov (United States)

Chrysikou, Evangelia G; Thompson-Schill, Sharon L

2010-06-01

Abstract The proposed theory can account for analogies based on learned relationships between elements in the source and target domains. However, its explanatory power regarding the discovery of new relationships during analogical reasoning is limited. We offer an alternative perspective for the role of PFC in analogical thought that may better address different types of analogical mappings.

Improved imaging of cochlear nerve hypoplasia using a 3-Tesla variable flip-angle turbo spin-echo sequence and a 7-cm surface coil.

Science.gov (United States)

Giesemann, Anja M; Raab, Peter; Lyutenski, Stefan; Dettmer, Sabine; Bültmann, Eva; Frömke, Cornelia; Lenarz, Thomas; Lanfermann, Heinrich; Goetz, Friedrich

2014-03-01

Magnetic resonance imaging of the temporal bone has an important role in decision making with regard to cochlea implantation, especially in children with cochlear nerve deficiency. The purpose of this study was to evaluate the usefulness of the combination of an advanced high-resolution T2-weighted sequence with a surface coil in a 3-Tesla magnetic resonance imaging scanner in cases of suspected cochlear nerve aplasia. Prospective study. Seven patients with cochlear nerve hypoplasia or aplasia were prospectively examined using a high-resolution three-dimensional variable flip-angle turbo spin-echo sequence using a surface coil, and the images were compared with the same sequence in standard resolution using a standard head coil. Three neuroradiologists evaluated the magnetic resonance images independently, rating the visibility of the nerves in diagnosing hypoplasia or aplasia. Eight ears in seven patients with hypoplasia or aplasia of the cochlear nerve were examined. The average age was 2.7 years (range, 9 months-5 years). Seven ears had accompanying malformations. The inter-rater reliability in diagnosing hypoplasia or aplasia was greater using the high-resolution three-dimensional variable flip-angle turbo spin-echo sequence (fixed-marginal kappa: 0.64) than with the same sequence in lower resolution (fixed-marginal kappa: 0.06). Examining cases of suspected cochlear nerve aplasia using the high-resolution three-dimensional variable flip-angle turbo spin-echo sequence in combination with a surface coil shows significant improvement over standard methods. © 2013 The American Laryngological, Rhinological and Otological Society, Inc.

A Novel Analog Reasoning Paradigm: New Insights in Intellectually Disabled Patients.

Science.gov (United States)

Curie, Aurore; Brun, Amandine; Cheylus, Anne; Reboul, Anne; Nazir, Tatjana; Bussy, Gérald; Delange, Karine; Paulignan, Yves; Mercier, Sandra; David, Albert; Marignier, Stéphanie; Merle, Lydie; de Fréminville, Bénédicte; Prieur, Fabienne; Till, Michel; Mortemousque, Isabelle; Toutain, Annick; Bieth, Eric; Touraine, Renaud; Sanlaville, Damien; Chelly, Jamel; Kong, Jian; Ott, Daniel; Kassai, Behrouz; Hadjikhani, Nouchine; Gollub, Randy L; des Portes, Vincent

2016-01-01

Intellectual Disability (ID) is characterized by deficits in intellectual functions such as reasoning, problem-solving, planning, abstract thinking, judgment, and learning. As new avenues are emerging for treatment of genetically determined ID (such as Down's syndrome or Fragile X syndrome), it is necessary to identify objective reliable and sensitive outcome measures for use in clinical trials. We developed a novel visual analogical reasoning paradigm, inspired by the Progressive Raven's Matrices, but appropriate for Intellectually Disabled patients. This new paradigm assesses reasoning and inhibition abilities in ID patients. We performed behavioural analyses for this task (with a reaction time and error rate analysis, Study 1) in 96 healthy controls (adults and typically developed children older than 4) and 41 genetically determined ID patients (Fragile X syndrome, Down syndrome and ARX mutated patients). In order to establish and quantify the cognitive strategies used to solve the task, we also performed an eye-tracking analysis (Study 2). Down syndrome, ARX and Fragile X patients were significantly slower and made significantly more errors than chronological age-matched healthy controls. The effect of inhibition on error rate was greater than the matrix complexity effect in ID patients, opposite to findings in adult healthy controls. Interestingly, ID patients were more impaired by inhibition than mental age-matched healthy controls, but not by the matrix complexity. Eye-tracking analysis made it possible to identify the strategy used by the participants to solve the task. Adult healthy controls used a matrix-based strategy, whereas ID patients used a response-based strategy. Furthermore, etiologic-specific reasoning differences were evidenced between ID patients groups. We suggest that this paradigm, appropriate for ID patients and developmental populations as well as adult healthy controls, provides an objective and quantitative assessment of visual

The Effect of Flywheel Unbalance on Gear Noise in the Hydraulic Power Plant Turbo-Generator

Directory of Open Access Journals (Sweden)

Tomeh Elias

2017-01-01

Full Text Available The Effect of Flywheel Unbalance on Gear Noise in the Hydraulic Power Plant Turbo-Generator. Hydraulic power plants are systems that produce electrical energy with high investment costs. In order to fulfil their goals, investments should create conditions for a safe production of energy in a long lasting and reliable way, and with the required power and quality. These goals are possible to reach by an optional control process linked to a systematic monitoring of the operating machinery state, using the method of vibration diagnostics. Lately, there has been an increase of noise level in the hydraulic power plants.

Performance Comparisons of Improved Regular Repeat Accumulate (RA and Irregular Repeat Accumulate (IRA Turbo Decoding

Directory of Open Access Journals (Sweden)

Ahmed Abdulkadhim Hamad

2017-08-01

Full Text Available In this paper, different techniques are used to improve the turbo decoding of regular repeat accumulate (RA and irregular repeat accumulate (IRA codes. The adaptive scaling of a-posteriori information produced by Soft-output Viterbi decoder (SOVA is proposed. The encoded pilots are another scheme that applied for short length RA codes. This work also suggests a simple and a fast method to generate a random interleaver having a free 4 cycle Tanner graph. Progressive edge growth algorithm (PEG is also studied and simulated to create the Tanner graphs which have a great girth.

Troubleshooting analog circuits

CERN Document Server

Pease, Robert A

1991-01-01

Troubleshooting Analog Circuits is a guidebook for solving product or process related problems in analog circuits. The book also provides advice in selecting equipment, preventing problems, and general tips. The coverage of the book includes the philosophy of troubleshooting; the modes of failure of various components; and preventive measures. The text also deals with the active components of analog circuits, including diodes and rectifiers, optically coupled devices, solar cells, and batteries. The book will be of great use to both students and practitioners of electronics engineering. Other

PERCEIVED IMPACT OF THE YOUTH ENTERPRISE DEVELOPMENT FUND ON THE YOUTH TOWARDS THE ESTABLISHMENT OF SMALL SCALE RURAL ENTERPRISES IN TURBO DIVISION, UASIN-GISHU COUNTY, KENYA

Directory of Open Access Journals (Sweden)

Jasper E Nyaura

2017-02-01

Full Text Available The inception of the Youth Enterprise Development Fund has seen the rise of youth groups in rural areas. This paper is thus aimed at understanding the impact of the fund towards the youth establishment of small scale enterprises in Turbo Division. A descriptive research design was used in this paper. Data was collected using focused group discussion and self-administered questionnaires thus they were administered to the selected youth groups found in selected parts of the Turbo Division. Purposive technique was used in the specific youth of aged bracket 18 year to 35 years. Further, purposive and stratified sampling techniques were used in targeted youth groups. The sample size used was 147 drawn from Turbo Division. The salient findings of the study are that indeed the youth joined the small scale enterprises to obtain benefits through collaborative efforts, to gain and obtain skills and experiences, obtaining start-up capital and finally due to the unemployment. Moreover, impact made by the fund on individual life included; promoting togetherness, promoting income and sustained livelihoods thus improved economic statues, and eventually enhanced skills and experience that led to acquiring of more skills by joining polytechnics. Furthermore the fund had enhanced group development and participation. It is recommended that there should be enhanced youth group sustainability towards proper utilization of the fund.

Analogical Reasoning in Geometry Education

Science.gov (United States)

Magdas, Ioana

2015-01-01

The analogical reasoning isn't used only in mathematics but also in everyday life. In this article we approach the analogical reasoning in Geometry Education. The novelty of this article is a classification of geometrical analogies by reasoning type and their exemplification. Our classification includes: analogies for understanding and setting a…

Analog and mixed-signal electronics

CERN Document Server

Stephan, Karl

2015-01-01

A practical guide to analog and mixed-signal electronics, with an emphasis on design problems and applications This book provides an in-depth coverage of essential analog and mixed-signal topics such as power amplifiers, active filters, noise and dynamic range, analog-to-digital and digital-to-analog conversion techniques, phase-locked loops, and switching power supplies. Readers will learn the basics of linear systems, types of nonlinearities and their effects, op-amp circuits, the high-gain analog filter-amplifier, and signal generation. The author uses system design examples to motivate

Meat analog: a review.

Science.gov (United States)

Malav, O P; Talukder, S; Gokulakrishnan, P; Chand, S

2015-01-01

The health-conscious consumers are in search of nutritious and convenient food item which can be best suited in their busy life. The vegetarianism is the key for the search of such food which resembles the meat in respect of nutrition and sensory characters, but not of animal origin and contains vegetable or its modified form, this is the point when meat analog evolved out and gets shape. The consumers gets full satisfaction by consumption of meat analog due to its typical meaty texture, appearance and the flavor which are being imparted during the skilled production of meat analog. The supplement of protein in vegetarian diet through meat alike food can be fulfilled by incorporating protein-rich vegetative food grade materials in meat analog and by adopting proper technological process which can promote the proper fabrication of meat analog with acceptable meat like texture, appearance, flavor, etc. The easily available vegetables, cereals, and pulses in India have great advantages and prospects to be used in food products and it can improve the nutritional and functional characters of the food items. The various form and functional characters of food items are available world over and attracts the meat technologists and the food processors to bring some innovativeness in meat analog and its presentation and marketability so that the acceptability of meat analog can be overgrown by the consumers.

Multiobjective Design of Turbo Injection Mode for Axial Flux Motor in Plastic Injection Molding Machine by Particle Swarm Optimization

Directory of Open Access Journals (Sweden)

Jian-Long Kuo

2015-01-01

Full Text Available This paper proposes a turbo injection mode (TIM for an axial flux motor to apply onto injection molding machine. Since the injection molding machine requires different speed and force parameters setting when finishing a complete injection process. The interleaved winding structure in the motor provides two different injection levels to provide enough injection forces. Two wye-wye windings are designed to switch two control modes conveniently. Wye-wye configuration is used to switch two force levels for the motor. When only one set of wye-winding is energized, field weakening function is achieved. Both of the torque and speed increase under field weakening operation. To achieve two control objectives for torque and speed of the motor, fuzzy based multiple performance characteristics index (MPCI with particle swarm optimization (PSO is used to find out the multiobjective optimal design solution. Both of the torque and speed are expected to be maximal at the same time. Three control factors are selected as studied factors: winding diameter, winding type, and air-gap. Experimental results show that both of the torque and speed increase under the optimal condition. This will provide enough large torque and speed to perform the turbo injection mode in injection process for the injection molding machine.

Children's Development of Analogical Reasoning: Insights from Scene Analogy Problems

Science.gov (United States)

Richland, Lindsey E.; Morrison, Robert G.; Holyoak, Keith J.

2006-01-01

We explored how relational complexity and featural distraction, as varied in scene analogy problems, affect children's analogical reasoning performance. Results with 3- and 4-year-olds, 6- and 7-year-olds, 9- to 11-year-olds, and 13- and 14-year-olds indicate that when children can identify the critical structural relations in a scene analogy…

ESD analog circuits and design

CERN Document Server

Voldman, Steven H

2014-01-01

A comprehensive and in-depth review of analog circuit layout, schematic architecture, device, power network and ESD design This book will provide a balanced overview of analog circuit design layout, analog circuit schematic development, architecture of chips, and ESD design.  It will start at an introductory level and will bring the reader right up to the state-of-the-art. Two critical design aspects for analog and power integrated circuits are combined. The first design aspect covers analog circuit design techniques to achieve the desired circuit performance. The second and main aspect pres

Performance of turbo high-pitch dual-source CT for coronary CT angiography: first ex vivo and patient experience

Energy Technology Data Exchange (ETDEWEB)

Morsbach, Fabian; Gordic, Sonja; Husarik, Daniela; Frauenfelder, Thomas; Alkadhi, Hatem [University Hospital Zurich, Institute of Diagnostic and Interventional Radiology, Zurich (Switzerland); Desbiolles, Lotus; Leschka, Sebastian [University Hospital Zurich, Institute of Diagnostic and Interventional Radiology, Zurich (Switzerland); Kantonsspital St. Gallen, Divison of Radiology and Nuclear Medicine, St. Gallen (Switzerland); Schmidt, Bernhard; Allmendinger, Thomas [Siemens AG, Healthcare Sector, Forchheim (Germany); Wildermuth, Simon [Kantonsspital St. Gallen, Divison of Radiology and Nuclear Medicine, St. Gallen (Switzerland)

2014-08-15

To evaluate image quality, maximal heart rate allowing for diagnostic imaging, and radiation dose of turbo high-pitch dual-source coronary computed tomographic angiography (CCTA). First, a cardiac motion phantom simulating heart rates (HRs) from 60-90 bpm in 5-bpm steps was examined on a third-generation dual-source 192-slice CT (prospective ECG-triggering, pitch 3.2; rotation time, 250 ms). Subjective image quality regarding the presence of motion artefacts was interpreted by two readers on a four-point scale (1, excellent; 4, non-diagnostic). Objective image quality was assessed by calculating distortion vectors. Thereafter, 20 consecutive patients (median, 50 years) undergoing clinically indicated CCTA were included. In the phantom study, image quality was rated diagnostic up to the HR75 bpm, with object distortion being 1 mm or less. Distortion increased above 1 mm at HR of 80-90 bpm. Patients had a mean HR of 66 bpm (47-78 bpm). Coronary segments were of diagnostic image quality for all patients with HR up to 73 bpm. Average effective radiation dose in patients was 0.6 ± 0.3 mSv. Our combined phantom and patient study indicates that CCTA with turbo high-pitch third-generation dual-source 192-slice CT can be performed at HR up to 75 bpm while maintaining diagnostic image quality, being associated with an average radiation dose of 0.6 mSv. (orig.)

Performance of turbo high-pitch dual-source CT for coronary CT angiography: first ex vivo and patient experience

International Nuclear Information System (INIS)

Morsbach, Fabian; Gordic, Sonja; Husarik, Daniela; Frauenfelder, Thomas; Alkadhi, Hatem; Desbiolles, Lotus; Leschka, Sebastian; Schmidt, Bernhard; Allmendinger, Thomas; Wildermuth, Simon

2014-01-01

To evaluate image quality, maximal heart rate allowing for diagnostic imaging, and radiation dose of turbo high-pitch dual-source coronary computed tomographic angiography (CCTA). First, a cardiac motion phantom simulating heart rates (HRs) from 60-90 bpm in 5-bpm steps was examined on a third-generation dual-source 192-slice CT (prospective ECG-triggering, pitch 3.2; rotation time, 250 ms). Subjective image quality regarding the presence of motion artefacts was interpreted by two readers on a four-point scale (1, excellent; 4, non-diagnostic). Objective image quality was assessed by calculating distortion vectors. Thereafter, 20 consecutive patients (median, 50 years) undergoing clinically indicated CCTA were included. In the phantom study, image quality was rated diagnostic up to the HR75 bpm, with object distortion being 1 mm or less. Distortion increased above 1 mm at HR of 80-90 bpm. Patients had a mean HR of 66 bpm (47-78 bpm). Coronary segments were of diagnostic image quality for all patients with HR up to 73 bpm. Average effective radiation dose in patients was 0.6 ± 0.3 mSv. Our combined phantom and patient study indicates that CCTA with turbo high-pitch third-generation dual-source 192-slice CT can be performed at HR up to 75 bpm while maintaining diagnostic image quality, being associated with an average radiation dose of 0.6 mSv. (orig.)

Endpoint Distinctiveness Facilitates Analogical Mapping in Pigeons

Science.gov (United States)

Hagmann, Carl Erick; Cook, Robert G.

2015-01-01

Analogical thinking necessitates mapping shared relations across two separate domains. We investigated whether pigeons could learn faster with ordinal mapping of relations across two physical dimensions (circle size & choice spatial position) relative to random mapping of these relations. Pigeons were trained to relate six circular samples of different sizes to horizontally positioned choice locations in a six alternative matching-to-sample task. Three pigeons were trained in a mapped condition in which circle size mapped directly onto choice spatial position. Three other pigeons were trained in a random condition in which the relations between size and choice position were arbitrarily assigned. The mapped group showed an advantage over the random group in acquiring this task. In a subsequent second phase, reassignment, relations between the dimensions were ordinally reversed for the mapped group and re-randomized for the random group. There was no difference in how quickly matching accuracy re-emerged in the two groups, although the mapped group eventually performed more accurately. Analyses suggested this mapped advantage was likely due endpoint distinctiveness and the benefits of proximity errors during choice responding rather than a conceptual or relational advantage attributable to the common or ordinal map of the two dimensions. This potential difficulty in mapping relations across dimensions may limit the pigeons’ capacity for more advanced types of analogical reasoning. PMID:25447511

The influence of the engine load on value and temperature distribution in the valve seats of turbo diesel engine

Directory of Open Access Journals (Sweden)

Aleksander HORNIK

2009-01-01

Full Text Available In this paper was presented the numerical computations of the influence of engine load on value and temperature distribution of characteristic surfaces of the heat transfer of the valve seats in Turbo diesel engine at the beginning phase of its work. The computations were performed by means of a two-zone combustion model, the boundary of III kind conditions and the finite elements method (FEM by adaptation of the COSMOS/M program.

Modernization of the turbo in the Laguna Verde Nuclear Power Plant; Modernizacion del turbogrupo en la Central Nuclear de Laguna Verde

Energy Technology Data Exchange (ETDEWEB)

Liebana, B.; Merino, A.; Cobos, A.; Gonzalez, J. J.

2010-07-01

The power increase of the Laguna Verde Nuclear Power Plant is a project for the rehabilitation and modernization of the turbo and associated equipment to get an increase of its power and of its service life. The project scope includes the design, the engineering, the equipment supply, the installation, the testing and the commissioning. This paper describes the first phase of the project.

Hydraulic Capacitor Analogy

Science.gov (United States)

Baser, Mustafa

2007-01-01

Students have difficulties in physics because of the abstract nature of concepts and principles. One of the effective methods for overcoming students' difficulties is the use of analogies to visualize abstract concepts to promote conceptual understanding. According to Iding, analogies are consistent with the tenets of constructivist learning…

Analog fourier transform channelizer and OFDM receiver

OpenAIRE

2007-01-01

An OFDM receiver having an analog multiplier based I-Q channelizing filter, samples and holds consecutive analog I-Q samples of an I-Q baseband, the I-Q basebands having OFDM sub-channels. A lattice of analog I-Q multipliers and analog I-Q summers concurrently receives the held analog I-Q samples, performs analog I-Q multiplications and analog I-Q additions to concurrently generate a plurality of analog I-Q output signals, representing an N-point discrete Fourier transform of the held analog ...

Analogical Thinking for Generation of Innovative Ideas: An Exploratory Study of Influential Factors

Directory of Open Access Journals (Sweden)

Eunyoung Kim

2016-07-01

Full Text Available Analogical thinking is one of the most effective tools to generate innovative ideas. It enables us to develop new ideas by transferring information from well-known domains and utilizing them in a novel domain. However, using analogical thinking does not always yield appropriate ideas, and there is a lack of consensus among researchers regarding the evaluation methods for assessing new ideas. Here, we define the appropriateness of generated ideas as having high structural and low superficial similarities with their source ideas. This study investigates the relationship between thinking process and the appropriateness of ideas generated through analogical thinking. We conducted four workshops with 22 students in order to collect the data. All generated ideas were assessed based on the definition of appropriateness in this study. The results show that participants who deliberate more before reaching the creative leap stage and those who are engaged in more trial and error for deciding the final domain of a new idea have a greater possibility of generating appropriate ideas. The findings suggest new strategies of designing workshops to enhance the appropriateness of new ideas.

Automatic regulation of the feedwater turbo-pump capacity for the single-turbine 1000 MW NPP unit

International Nuclear Information System (INIS)

Pavlysh, O.N.; Garbuzov, I.P.; Reukov, Yu.N.

1985-01-01

A schematic of the flow regulators (FR) of feedwater turbo-pumps (FTP) for the single-turbine 1000 MW NPP unit is presented. The FR operate in response to feedwoter signals from FTP or in response to FTP rotor rotational speed and control automatic speed governars. The FR automatic regulation ensures limitation of FTP rotor maximum rotational speed at a feedwater flow rate excess equal to 3600 T/h. The transients in the automatic regulation system are considered. Production tests of FTP FR confirmed the FR operation reliability and the right choice of the regulator concept and structure

Computer simulation of the heavy-duty turbo-compounded diesel cycle for studies of engine efficiency and performance

Science.gov (United States)

Assanis, D. N.; Ekchian, J. A.; Heywood, J. B.; Replogle, K. K.

1984-01-01

Reductions in heat loss at appropriate points in the diesel engine which result in substantially increased exhaust enthalpy were shown. The concepts for this increased enthalpy are the turbocharged, turbocompounded diesel engine cycle. A computer simulation of the heavy duty turbocharged turbo-compounded diesel engine system was undertaken. This allows the definition of the tradeoffs which are associated with the introduction of ceramic materials in various parts of the total engine system, and the study of system optimization. The basic assumptions and the mathematical relationships used in the simulation of the model engine are described.

Inductive, Analogical, and Communicative Generalization

Directory of Open Access Journals (Sweden)

Adri Smaling

2003-03-01

Full Text Available Three forms of inductive generalization - statistical generalization, variation-based generalization and theory-carried generalization - are insufficient concerning case-to-case generalization, which is a form of analogical generalization. The quality of case-to-case generalization needs to be reinforced by setting up explicit analogical argumentation. To evaluate analogical argumentation six criteria are discussed. Good analogical reasoning is an indispensable support to forms of communicative generalization - receptive and responsive (participative generalization — as well as exemplary generalization.

Dynamic Stability Study of Static Gas Bearing for Small Cryogenic Turbo-Expander

International Nuclear Information System (INIS)

Wang Xuemin; Zhuang Ming; Zhang Qiyong; Li Shanshan; Fu Bao

2011-01-01

An experimental method is presented to analyze the dynamic stability of the gas bearing for small cryogenic turbo-expanders. The rotation imbalance response and the shape of the rotor orbit were obtained for different speeds up to 110,000 rpm, and the critical speed of the rotor-bearing system was determined by a Bode diagram. An FFT signal analytical method was applied to identify the resonance frequency, and the waterfall plot was presented. During the whole process of speeding up to the designed speed of 110,000 rpm, the rotor-bearing works stably with no whirl instability, which is validated in a waterfall plot. Also, the tested rotor-bearing model was analyzed theoretically. It was proved that the experimental results were highly consistent with those of theoretical calculations. Thus the experimental method proposed here to analyze the dynamic stability of the gas bearing is feasible. (fusion engineering)

Some problems raised by the operation of large nuclear turbo-generator sets. Solutions proposed for the protection of large size generators

International Nuclear Information System (INIS)

Chaumienne, J.-P.

1976-01-01

The operating requirements of nuclear power stations call for relays with ever increasing performances. This urges the development of new electronic systems while giving high importance to their reliability. So as to provide for easy application and minitoring of the relays, even when the turbo-generator unit is operating, a new cubicle design is considered which offers maximum safety and flexibility in use [fr

How to Avoid Errors in Error Propagation: Prediction Intervals and Confidence Intervals in Forest Biomass

Science.gov (United States)

Lilly, P.; Yanai, R. D.; Buckley, H. L.; Case, B. S.; Woollons, R. C.; Holdaway, R. J.; Johnson, J.

2016-12-01

Calculations of forest biomass and elemental content require many measurements and models, each contributing uncertainty to the final estimates. While sampling error is commonly reported, based on replicate plots, error due to uncertainty in the regression used to estimate biomass from tree diameter is usually not quantified. Some published estimates of uncertainty due to the regression models have used the uncertainty in the prediction of individuals, ignoring uncertainty in the mean, while others have propagated uncertainty in the mean while ignoring individual variation. Using the simple case of the calcium concentration of sugar maple leaves, we compare the variation among individuals (the standard deviation) to the uncertainty in the mean (the standard error) and illustrate the declining importance in the prediction of individual concentrations as the number of individuals increases. For allometric models, the analogous statistics are the prediction interval (or the residual variation in the model fit) and the confidence interval (describing the uncertainty in the best fit model). The effect of propagating these two sources of error is illustrated using the mass of sugar maple foliage. The uncertainty in individual tree predictions was large for plots with few trees; for plots with 30 trees or more, the uncertainty in individuals was less important than the uncertainty in the mean. Authors of previously published analyses have reanalyzed their data to show the magnitude of these two sources of uncertainty in scales ranging from experimental plots to entire countries. The most correct analysis will take both sources of uncertainty into account, but for practical purposes, country-level reports of uncertainty in carbon stocks, as required by the IPCC, can ignore the uncertainty in individuals. Ignoring the uncertainty in the mean will lead to exaggerated estimates of confidence in estimates of forest biomass and carbon and nutrient contents.

Analogical Reasoning and Computer Programming.

Science.gov (United States)

Clement, Catherine A.; And Others

1986-01-01

A study of correlations between analogical reasoning and Logo programming mastery among female high school students related the results of pretests of analogical reasoning to posttests of programming mastery. A significant correlation was found between analogical reasoning and the ability to write subprocedures for use in several different…

Analog CMOS peak detect and hold circuits. Part 2. The two-phase offset-free and derandomizing configuration

CERN Document Server

De Geronimo, G; Kandasamy, A

2002-01-01

An analog CMOS peak detect and hold (PDH) circuit, which combines high speed and accuracy, rail-to-rail sensing and driving, low power, and buffering is presented. It is based on a configuration that cancels the major error sources of the classical CMOS PDH, including offset and common mode gain, by re-using the same amplifier for tracking, peak sensing, and output buffering. By virtue of its high absolute accuracy, two or more PDHs can be used in parallel to serve as a data-driven analog memory for derandomization. The first experimental results on the new peak detector and derandomizer (PDD) circuit, fabricated in 0.35 mu m CMOS technology, include a 0.2% absolute accuracy for pulses with 500 ns peaking time, 2.7 V linear input range, 3.3 mW power dissipation, 250 mV/s droop rate, and negligible dead time. The use of such a high performance analog PDD can greatly relax the requirements on the digitization in multi-channel systems.

A Novel Analog Reasoning Paradigm: New Insights in Intellectually Disabled Patients.

Directory of Open Access Journals (Sweden)

Aurore Curie

Full Text Available Intellectual Disability (ID is characterized by deficits in intellectual functions such as reasoning, problem-solving, planning, abstract thinking, judgment, and learning. As new avenues are emerging for treatment of genetically determined ID (such as Down's syndrome or Fragile X syndrome, it is necessary to identify objective reliable and sensitive outcome measures for use in clinical trials.We developed a novel visual analogical reasoning paradigm, inspired by the Progressive Raven's Matrices, but appropriate for Intellectually Disabled patients. This new paradigm assesses reasoning and inhibition abilities in ID patients.We performed behavioural analyses for this task (with a reaction time and error rate analysis, Study 1 in 96 healthy controls (adults and typically developed children older than 4 and 41 genetically determined ID patients (Fragile X syndrome, Down syndrome and ARX mutated patients. In order to establish and quantify the cognitive strategies used to solve the task, we also performed an eye-tracking analysis (Study 2.Down syndrome, ARX and Fragile X patients were significantly slower and made significantly more errors than chronological age-matched healthy controls. The effect of inhibition on error rate was greater than the matrix complexity effect in ID patients, opposite to findings in adult healthy controls. Interestingly, ID patients were more impaired by inhibition than mental age-matched healthy controls, but not by the matrix complexity. Eye-tracking analysis made it possible to identify the strategy used by the participants to solve the task. Adult healthy controls used a matrix-based strategy, whereas ID patients used a response-based strategy. Furthermore, etiologic-specific reasoning differences were evidenced between ID patients groups.We suggest that this paradigm, appropriate for ID patients and developmental populations as well as adult healthy controls, provides an objective and quantitative assessment of

Analogical reasoning in children with specific language impairment: Evidence from a scene analogy task.

Science.gov (United States)

Krzemien, Magali; Jemel, Boutheina; Maillart, Christelle

2017-01-01

Analogical reasoning is a human ability that maps systems of relations. It develops along with relational knowledge, working memory and executive functions such as inhibition. It also maintains a mutual influence on language development. Some authors have taken a greater interest in the analogical reasoning ability of children with language disorders, specifically those with specific language impairment (SLI). These children apparently have weaker analogical reasoning abilities than their aged-matched peers without language disorders. Following cognitive theories of language acquisition, this deficit could be one of the causes of language disorders in SLI, especially those concerning productivity. To confirm this deficit and its link to language disorders, we use a scene analogy task to evaluate the analogical performance of SLI children and compare them to controls of the same age and linguistic abilities. Results show that children with SLI perform worse than age-matched peers, but similar to language-matched peers. They are more influenced by increased task difficulty. The association between language disorders and analogical reasoning in SLI can be confirmed. The hypothesis of limited processing capacity in SLI is also being considered.

PEMETAAN ANALOGI PADA KONSEP ABSTRAK FISIKA

Directory of Open Access Journals (Sweden)

Nyoto Suseno

2014-11-01

Full Text Available The research of any where founded majority students have common difficulties in abstract physics concept. The result of observation, lecturers have problem  in teaching implementation of abstract concepts on physics learning. The objective of this research is to find out the ways how to overcome this problem. The research place of  physics education programs and senior high school. The data are colected by quetionere, observation and interview. The lecturer behavior to making out this case is use of analogy to make concrete a abstract concept. This action is true, because the analogies are dynamic tools that facilitate understanding, rather than representations of the correct and static explanations. Using analogies not only promoted profound understanding of abstract concept, but also helped students overcome their misconceptions. However used analogy in teaching not yet planed with seriousness, analogy used spontanously with the result that less optimal. By planing and selecting right analogy, the role of analogy can be achieved the optimal result. Therefore, it is important to maping analogies of abstract consepts on physics learning.

For a new look at 'lexical errors': evidence from semantic approximations with verbs in aphasia.

Science.gov (United States)

Duvignau, Karine; Tran, Thi Mai; Manchon, Mélanie

2013-08-01

The ability to understand the similarity between two phenomena is fundamental for humans. Designated by the term analogy in psychology, this ability plays a role in the categorization of phenomena in the world and in the organisation of the linguistic system. The use of analogy in language often results in non-standard utterances, particularly in speakers with aphasia. These non-standard utterances are almost always studied in a nominal context and considered as errors. We propose a study of the verbal lexicon and present findings that measure, by an action-video naming task, the importance of verb-based non-standard utterances made by 17 speakers with aphasia ("la dame déshabille l'orange"/the lady undresses the orange, "elle casse la tomate"/she breaks the tomato). The first results we have obtained allow us to consider these type of utterances from a new perspective: we propose to eliminate the label of "error", suggesting that they may be viewed as semantic approximations based upon a relationship of inter-domain synonymy and are ingrained in the heart of the lexical system.

Science Teachers' Analogical Reasoning

Science.gov (United States)

Mozzer, Nilmara Braga; Justi, Rosária

2013-01-01

Analogies can play a relevant role in students' learning. However, for the effective use of analogies, teachers should not only have a well-prepared repertoire of validated analogies, which could serve as bridges between the students' prior knowledge and the scientific knowledge they desire them to understand, but also know how to…

Endpoint distinctiveness facilitates analogical mapping in pigeons.

Science.gov (United States)

Hagmann, Carl Erick; Cook, Robert G

2015-03-01

Analogical thinking necessitates mapping shared relations across two separate domains. We investigated whether pigeons could learn faster with ordinal mapping of relations across two physical dimensions (circle size & choice spatial position) relative to random mapping of these relations. Pigeons were trained to relate six circular samples of different sizes to horizontally positioned choice locations in a six alternative matching-to-sample task. Three pigeons were trained in a mapped condition in which circle size mapped directly onto choice spatial position. Three other pigeons were trained in a random condition in which the relations between size and choice position were arbitrarily assigned. The mapped group showed an advantage over the random group in acquiring this task. In a subsequent second phase, relations between the dimensions were ordinally reversed for the mapped group and re-randomized for the random group. There was no difference in how quickly matching accuracy re-emerged in the two groups, although the mapped group eventually performed more accurately. Analyses suggested this mapped advantage was likely due to endpoint distinctiveness and the benefits of proximity errors during choice responding rather than a conceptual or relational advantage attributable to the common or ordinal mapping of the two dimensions. This potential difficulty in mapping relations across dimensions may limit the pigeons' capacity for more advanced types of analogical reasoning. This article is part of a Special Issue entitled: Tribute to Tom Zentall. Copyright © 2014 Elsevier B.V. All rights reserved.

Analog circuits cookbook

CERN Document Server

Hickman, Ian

2013-01-01

Analog Circuits Cookbook presents articles about advanced circuit techniques, components and concepts, useful IC for analog signal processing in the audio range, direct digital synthesis, and ingenious video op-amp. The book also includes articles about amplitude measurements on RF signals, linear optical imager, power supplies and devices, and RF circuits and techniques. Professionals and students of electrical engineering will find the book informative and useful.

Advances in Analog Circuit Design 2015

CERN Document Server

Baschirotto, Andrea; Harpe, Pieter

2016-01-01

This book is based on the 18 tutorials presented during the 24th workshop on Advances in Analog Circuit Design. Expert designers present readers with information about a variety of topics at the frontier of analog circuit design, including low-power and energy-efficient analog electronics, with specific contributions focusing on the design of efficient sensor interfaces and low-power RF systems. This book serves as a valuable reference to the state-of-the-art, for anyone involved in analog circuit research and development. ·         Provides a state-of-the-art reference in analog circuit design, written by experts from industry and academia; ·         Presents material in a tutorial-based format; ·         Includes coverage of high-performance analog-to-digital and digital to analog converters, integrated circuit design in scaled technologies, and time-domain signal processing.

Discrete polyphase matched filtering-based soft timing estimation for mobile wireless systems

CSIR Research Space (South Africa)

Olwal, TO

2009-01-01

Full Text Available of the communication system is conserved. However, the computational complexity of ideal turbo synchronization is increased by 50%. Several simulation tests on bit error rate (BER) and block error rate (BLER) versus low SNR reveal that the proposed iterative soft...

Students' Pre- and Post-Teaching Analogical Reasoning when They Draw Their Analogies

Science.gov (United States)

Mozzer, Nilmara Braga; Justi, Rosaria

2012-01-01

Analogies are parts of human thought. From them, we can acquire new knowledge or change that which already exists in our cognitive structure. In this sense, understanding the analogical reasoning process becomes an essential condition to understand how we learn. Despite the importance of such an understanding, there is no general agreement in…

Analogical proportions: another logical view

Science.gov (United States)

Prade, Henri; Richard, Gilles

This paper investigates the logical formalization of a restricted form of analogical reasoning based on analogical proportions, i.e. statements of the form a is to b as c is to d. Starting from a naive set theoretic interpretation, we highlight the existence of two noticeable companion proportions: one states that a is to b the converse of what c is to d (reverse analogy), while the other called paralogical proportion expresses that what a and b have in common, c and d have it also. We identify the characteristic postulates of the three types of proportions and examine their consequences from an abstract viewpoint. We further study the properties of the set theoretic interpretation and of the Boolean logic interpretation, and we provide another light on the understanding of the role of permutations in the modeling of the three types of proportions. Finally, we address the use of these proportions as a basis for inference in a propositional setting, and relate it to more general schemes of analogical reasoning. The differences between analogy, reverse-analogy, and paralogy is still emphasized in a three-valued setting, which is also briefly presented.

Performance Effects of Display Incogruity in a Digital and Analog Clock Reading Task

Science.gov (United States)

Comstock, J. Raymond, Jr.; Derks, Peter L.

2004-01-01

In an era of increasing automation, it is important to design displays and input devices that minimize human error. In this context, information concerning the human response to the detection of incongruous information is important. Such incongruous information can be operationalized as unexpected (perhaps erroneous) information on which a decision by the human or operation by an automated system is based. In the aviation environment, decision making when faced with inadequate, incomplete, or incongruous information may occur in a failure scenario. An additional challenge facing the human operator in automated environments is maintaining alertness or vigilance. The vigilance issue is of particular concern as a factor that may interact with performance when faced with inadequate, incomplete, or incongruous information. From the literature on eye-scan behavior we know that the time spent looking at a particular display or indicator is a function of the type of information one is trying to discern from the display. For example, quick glances are all it takes for confirming that an indicator is in a normal position or range, whereas a continuous look of several seconds may be required for confirmation that a complex control input is having the desired effect. Important to consider is that while an extended look takes place, visual input from other sources may be missed. Much like an extended look, the interpretation of incongruous information may require extra time. The present experiment was designed to explore the performance consequences of a decision making task when incongruous information was presented. For this experiment a display incongruity was created on a subset of trials of a clock reading laboratory task. Display incongruity was made possible through presentation of 'impossible' times (e.g. 1:65 or 11:90). Subjects made 'same' 'different' decisions and keyboard responses to pairings of Analog-Analog (AA), Digital-Digital (DD), and Analog- Digital (AD

Multi-scale entropy analysis of VR-based analog-digital system of the operator mental workload

International Nuclear Information System (INIS)

Lee Chunyi; Hung Tamin; Sun Tienlung; Yang Chihwei; Cheng Tsungchieh; Yang Lichen

2011-01-01

In the past, serious accidents of nuclear power plant usually had relation with the negligence, error handling and wrong decisions of operators. Therefore, to understand and be able to measure mental workload levels of operators are significant for safety issues in the nuclear power plant, especially when operators face emergency conditions. Therefore, this study is to determine the physiological indicators to measure the operator in the task of mental workload. This paper was to use electrocardiogram (ECG) measurements, to collect the RR-Interval data; heart rate variability (HRV) to analysis the complexity of the operator. After importing the data to calculate heart rate variability of complexity analysis, it can help us to understand the operator for the analog-digital platform adaptation. The virtual analog-digital nuclear plant control room is built using a 3D game development tool called Unity3D. (author)

Design of a long pulse and low drift analog integrator in HT-7

International Nuclear Information System (INIS)

Liu Dongmei; Wan Baonian; Shen Biao

2007-01-01

Magnetic measurements are a fundamental diagnostic system for Tokamak. Inductive magnetic coils are used on HT-7. So the integrator is required to determine the magnetic field strength. This paper discusses the traditional analog integrator, and introduces a new integrator based on real-time drift compensation schemes. This new design can significantly reduce the integral error caused by input offset, temperature-induced drift, noise and so on. Operation in the HT-7 Tokamak shows that very low drift and noise characteristics compatible of the now integrators can meet requirement of long pulse discharges. (authors)

Analog circuit design art, science and personalities

CERN Document Server

Williams, Jim

1991-01-01

This book is far more than just another tutorial or reference guide - it's a tour through the world of analog design, combining theory and applications with the philosophies behind the design process. Readers will learn how leading analog circuit designers approach problems and how they think about solutions to those problems. They'll also learn about the `analog way' - a broad, flexible method of thinking about analog design tasks.A comprehensive and useful guide to analog theory and applications. Covers visualizing the operation of analog circuits. Looks at how to rap

Resistive RAMs as analog trimming elements

Science.gov (United States)

Aziza, H.; Perez, A.; Portal, J. M.

2018-04-01

This work investigates the use of Resistive Random Access Memory (RRAM) as an analog trimming device. The analog storage feature of the RRAM cell is evaluated and the ability of the RRAM to hold several resistance states is exploited to propose analog trim elements. To modulate the memory cell resistance, a series of short programming pulses are applied across the RRAM cell allowing a fine calibration of the RRAM resistance. The RRAM non volatility feature makes the analog device powers up already calibrated for the system in which the analog trimmed structure is embedded. To validate the concept, a test structure consisting of a voltage reference is evaluated.

Error-related brain activity and error awareness in an error classification paradigm.

Science.gov (United States)

Di Gregorio, Francesco; Steinhauser, Marco; Maier, Martin E

2016-10-01

Error-related brain activity has been linked to error detection enabling adaptive behavioral adjustments. However, it is still unclear which role error awareness plays in this process. Here, we show that the error-related negativity (Ne/ERN), an event-related potential reflecting early error monitoring, is dissociable from the degree of error awareness. Participants responded to a target while ignoring two different incongruent distractors. After responding, they indicated whether they had committed an error, and if so, whether they had responded to one or to the other distractor. This error classification paradigm allowed distinguishing partially aware errors, (i.e., errors that were noticed but misclassified) and fully aware errors (i.e., errors that were correctly classified). The Ne/ERN was larger for partially aware errors than for fully aware errors. Whereas this speaks against the idea that the Ne/ERN foreshadows the degree of error awareness, it confirms the prediction of a computational model, which relates the Ne/ERN to post-response conflict. This model predicts that stronger distractor processing - a prerequisite of error classification in our paradigm - leads to lower post-response conflict and thus a smaller Ne/ERN. This implies that the relationship between Ne/ERN and error awareness depends on how error awareness is related to response conflict in a specific task. Our results further indicate that the Ne/ERN but not the degree of error awareness determines adaptive performance adjustments. Taken together, we conclude that the Ne/ERN is dissociable from error awareness and foreshadows adaptive performance adjustments. Our results suggest that the relationship between the Ne/ERN and error awareness is correlative and mediated by response conflict. Copyright © 2016 Elsevier Inc. All rights reserved.

Fast multichannel analog storage system

International Nuclear Information System (INIS)

Freytag, D.R.

1982-11-01

A Multichannel Analog Storage System based on a commercial 32-channel parallel in/serial out (PISO) analog shift register is described. The basic unit is a single width CAMAC module containing 512 analog cells and the associated logic for data storage and subsequent readout. At sampling rates of up to 30 MHz the signals are strobed directly into the PISO. At higher rates signals are strobed into a fast presampling stage and subsequently transferred in block form into an array of PISO's. Sampling rates of 300 MHz have been achieved with the present device and 1000 MHz are possible with improved signal drivers. The system is well suited for simultaneous handling of many signal channels with moderate numbers of samples in each channel. RMS noise over full scale signal has been measured as 1:3000 (approx. = 11 bit). However, nonlinearities in the response and differences in sensitivity of the analog cells require an elaborate calibration system in order to realize 11 bit accuracy for the analog information

Automating analog design: Taming the shrew

Science.gov (United States)

Barlow, A.

1990-01-01

The pace of progress in the design of integrated circuits continues to amaze observers inside and outside of the industry. Three decades ago, a 50 transistor chip was a technological wonder. Fifteen year later, a 5000 transistor device would 'wow' the crowds. Today, 50,000 transistor chips will earn a 'not too bad' assessment, but it takes 500,000 to really leave an impression. In 1975 a typical ASIC device had 1000 transistors, took one year to first samples (and two years to production) and sold for about 5 cents per transistor. Today's 50,000 transistor gate array takes about 4 months from spec to silicon, works the first time, and sells for about 0.02 cents per transistor. Fifteen years ago, the single most laborious and error prone step in IC design was the physical layout. Today, most IC's never see the hand of a layout designer: and automatic place and route tool converts the engineer's computer captured schematic to a complete physical design using a gate array or a library of standard cells also created by software rather than by designers. CAD has also been a generous benefactor to the digital design process. The architect of today's digital systems creates the design using an RTL or other high level simulator. Then the designer pushes a button to invoke the logic synthesizer-optimizer tool. A fault analyzer checks the result for testability and suggests where scan based cells will improve test coverage. One obstinate holdout amidst this parade of progress is the automation of analog design and its reduction to semi-custom techniques. This paper investigates the application of CAD techniques to analog design.

THE RELIABILITY AND ACCURACY OF THE TRIPLE MEASUREMENTS OF ANALOG PROCESS VARIABLES

Directory of Open Access Journals (Sweden)

V. A. Anishchenko

2017-01-01

Full Text Available The increase in unit capacity of electric equipment as well as complication of technological processes, devices control and management of the latter in power plants and substations demonstrate the need to improve the reliability and accuracy of measurement information characterizing the state of the objects being managed. The mentioned objective is particularly important for nuclear power plants, where the price of inaccuracy of measurement responsible process variables is particularly high and the error might lead to irreparable consequences. Improving the reliability and accuracy of measurements along with the improvement of the element base is provided by methods of operational validation. These methods are based on the use of information redundancy (structural, topological, temporal. In particular, information redundancy can be achieved by the simultaneous measurement of one analog variable by two (duplication or three devices (triplication i.e., triple redundancy. The problem of operational control of the triple redundant system of measurement of electrical analog variables (currents, voltages, active and reactive power and energy is considered as a special case of signal processing by an orderly sampling on the basis of majority transformation and transformation being close to majority one. Difficulties in monitoring the reliability of measurements are associated with the two tasks. First, one needs to justify the degree of truncation of the distributions of random errors of measurements and allowable residuals of the pairwise differences of the measurement results. The second task consists in formation of the algorithm of joint processing of a set of separate measurements determined as valid. The quality of control is characterized by the reliability, which adopted the synonym of validity, and accuracy of the measuring system. Taken separately, these indicators might lead to opposite results. A compromise solution is therefore proposed

A novel analog/digital reconfigurable automatic gain control with a novel DC offset cancellation circuit

Energy Technology Data Exchange (ETDEWEB)

He Xiaofeng; Ye Tianchun [Institute of Microelectronics, Chinese Academy of Science, Beijing 100029 (China); Mo Taishan; Ma Chengyan, E-mail: hexiaofeng@casic.ac.cn [Hangzhou Zhongke Microelectronics Co, Ltd, Hangzhou 310053 (China)

2011-02-15

An analog/digital reconfigurable automatic gain control (AGC) circuit with a novel DC offset cancellation circuit for a direct-conversion receiver is presented. The AGC is analog/digital reconfigurable in order to be compatible with different baseband chips. What's more, a novel DC offset cancellation (DCOC) circuit with an HPCF (high pass cutoff frequency) less than 10 kHz is proposed. The AGC is fabricated by a 0.18 {mu}m CMOS process. Under analog control mode, the AGC achieves a 70 dB dynamic range with a 3 dB-bandwidth larger than 60 MHz. Under digital control mode, through a 5-bit digital control word, the AGC shows a 64 dB gain control range by 2 dB each step with a gain error of less than 0.3 dB. The DC offset cancellation circuits can suppress the output DC offset voltage to be less than 1.5 mV, while the offset voltage of 40 mV is introduced into the input. The overall power consumption is less than 3.5 mA, and the die area is 800 x 300 {mu}m{sup 2}. (semiconductor integrated circuits)

Prospective Study of Plasmodium vivax Malaria Recurrence after Radical Treatment with a Chloroquine-Primaquine Standard Regimen in Turbo, Colombia

Science.gov (United States)

Blair, Silvia; Akinyi Okoth, Sheila; Udhayakumar, Venkatachalam; Marcet, Paula L.; Escalante, Ananias A.; Alexander, Neal; Rojas, Carlos

2016-01-01

Plasmodium vivax recurrences help maintain malaria transmission. They are caused by recrudescence, reinfection, or relapse, which are not easily differentiated. A longitudinal observational study took place in Turbo municipality, Colombia. Participants with uncomplicated P. vivax infection received supervised treatment concomitantly with 25 mg/kg chloroquine and 0.25 mg/kg/day primaquine for 14 days. Incidence of recurrence was assessed over 180 days. Samples were genotyped, and origins of recurrences were established. A total of 134 participants were enrolled between February 2012 and July 2013, and 87 were followed for 180 days, during which 29 recurrences were detected. The cumulative incidence of first recurrence was 24.1% (21/87) (95% confidence interval [CI], 14.6 to 33.7%), and 86% (18/21) of these events occurred between days 51 and 110. High genetic diversity of P. vivax strains was found, and 12.5% (16/128) of the infections were polyclonal. Among detected recurrences, 93.1% (27/29) of strains were genotyped as genetically identical to the strain from the previous infection episode, and 65.5% (19/29) of infections were classified as relapses. Our results indicate that there is a high incidence of P. vivax malaria recurrence after treatment in Turbo municipality, Colombia, and that a large majority of these episodes are likely relapses from the previous infection. We attribute this to the primaquine regimen currently used in Colombia, which may be insufficient to eliminate hypnozoites. PMID:27185794

Applying the Analog Configurability Test Approach in a Wireless Sensor Network Application

Directory of Open Access Journals (Sweden)

Agustín Laprovitta

2014-01-01

Full Text Available This work addresses the application of the analog configurability test (ACT approach for an embedded analog configurable circuit (EACC, composed of operational amplifiers and interconnection resources that are embedded in the MSP430xG461x microcontrollers family. This test strategy is particularly useful for in-field application requiring reliability, safe operation, or fault tolerance characteristics. Our test proposal consists of programming a reduced set of available configurations for the EACC and testing its functionality by measuring only a few key parameters. The processor executes an embedded test routine that sequentially programs selected configurations, sets the test stimulus, acquires data from the internal ADC, and performs required calculations. The test approach is experimentally evaluated using an embedded system-based real application board. Our experimental results show very good repeatability, with very low errors. These results show that the ACT proposed here is useful for testing the functionality of the circuit under test in a real application context by using a simple strategy at a very low cost.

Electrical Circuits and Water Analogies

Science.gov (United States)

Smith, Frederick A.; Wilson, Jerry D.

1974-01-01

Briefly describes water analogies for electrical circuits and presents plans for the construction of apparatus to demonstrate these analogies. Demonstrations include series circuits, parallel circuits, and capacitors. (GS)

Producing and Recognizing Analogical Relations

Science.gov (United States)

Lipkens, Regina; Hayes, Steven C

2009-01-01

Analogical reasoning is an important component of intelligent behavior, and a key test of any approach to human language and cognition. Only a limited amount of empirical work has been conducted from a behavior analytic point of view, most of that within Relational Frame Theory (RFT), which views analogy as a matter of deriving relations among relations. The present series of four studies expands previous work by exploring the applicability of this model of analogy to topography-based rather than merely selection-based responses and by extending the work into additional relations, including nonsymmetrical ones. In each of the four studies participants pretrained in contextual control over nonarbitrary stimulus relations of sameness and opposition, or of sameness, smaller than, and larger than, learned arbitrary stimulus relations in the presence of these relational cues and derived analogies involving directly trained relations and derived relations of mutual and combinatorial entailment, measured using a variety of productive and selection-based measures. In Experiment 1 participants successfully recognized analogies among stimulus networks containing same and opposite relations; in Experiment 2 analogy was successfully used to extend derived relations to pairs of novel stimuli; in Experiment 3 the procedure used in Experiment 1 was extended to nonsymmetrical comparative relations; in Experiment 4 the procedure used in Experiment 2 was extended to nonsymmetrical comparative relations. Although not every participant showed the effects predicted, overall the procedures occasioned relational responses consistent with an RFT account that have not yet been demonstrated in a behavior-analytic laboratory setting, including productive responding on the basis of analogies. PMID:19230515

Challenges in Using Analogies

Science.gov (United States)

Lin, Shih-Yin; Singh, Chandralekha

2011-01-01

Learning physics requires understanding the applicability of fundamental principles in a variety of contexts that share deep features. One way to help students learn physics is via analogical reasoning. Students can be taught to make an analogy between situations that are more familiar or easier to understand and another situation where the same…

The Micro-Category Account of Analogy

Science.gov (United States)

Green, Adam E.; Fugelsang, Jonathan A.; Kraemer, David J. M.; Dunbar, Kevin N.

2008-01-01

Here, we investigate how activation of mental representations of categories during analogical reasoning influences subsequent cognitive processing. Specifically, we present and test the central predictions of the "Micro-Category" account of analogy. This account emphasizes the role of categories in aligning terms for analogical mapping. In a…

Priming analogical reasoning with false memories.

Science.gov (United States)

Howe, Mark L; Garner, Sarah R; Threadgold, Emma; Ball, Linden J

2015-08-01

Like true memories, false memories are capable of priming answers to insight-based problems. Recent research has attempted to extend this paradigm to more advanced problem-solving tasks, including those involving verbal analogical reasoning. However, these experiments are constrained inasmuch as problem solutions could be generated via spreading activation mechanisms (much like false memories themselves) rather than using complex reasoning processes. In three experiments we examined false memory priming of complex analogical reasoning tasks in the absence of simple semantic associations. In Experiment 1, we demonstrated the robustness of false memory priming in analogical reasoning when backward associative strength among the problem terms was eliminated. In Experiments 2a and 2b, we extended these findings by demonstrating priming on newly created homonym analogies that can only be solved by inhibiting semantic associations within the analogy. Overall, the findings of the present experiments provide evidence that the efficacy of false memory priming extends to complex analogical reasoning problems.

Children's analogical reasoning about natural phenomena.

Science.gov (United States)

Pauen, S; Wilkening, F

1997-10-01

This report investigates children's analogical reasoning in a physics task, using an analogy generated by the children rather than by the experimenter. A total of 127 elementary school children took part in three related studies. Children learned to predict the behavior of a balance scale. Later, they were asked to solve a force interaction problem. Two versions of the balance scale training were devised: version A suggested an incorrect solution to the target problem (negative analogy), and version B suggested a correct solution to the target problem (positive analogy). In Study 1, 9- to 10-year-olds showed spontaneous transfer in both training conditions. In Study 2, 7-year-olds did not show any transfer in the positive analogy condition. Study 3 revealed that the lack of transfer in younger children was not due to a failure either to notice the analogy or to perform the mapping. Instead, 7-year-olds transferred only selected aspects of the correct solution. Copyright 1997 Academic Press.

Working memory predicts children's analogical reasoning.

Science.gov (United States)

Simms, Nina K; Frausel, Rebecca R; Richland, Lindsey E

2018-02-01

Analogical reasoning is the cognitive skill of drawing relationships between representations, often between prior knowledge and new representations, that allows for bootstrapping cognitive and language development. Analogical reasoning proficiency develops substantially during childhood, although the mechanisms underlying this development have been debated, with developing cognitive resources as one proposed mechanism. We explored the role of executive function (EF) in supporting children's analogical reasoning development, with the goal of determining whether predicted aspects of EF were related to analogical development at the level of individual differences. We assessed 5- to 11-year-old children's working memory, inhibitory control, and cognitive flexibility using measures from the National Institutes of Health Toolbox Cognition battery. Individual differences in children's working memory best predicted performance on an analogical mapping task, even when controlling for age, suggesting a fundamental interrelationship between analogical reasoning and working memory development. These findings underscore the need to consider cognitive capacities in comprehensive theories of children's reasoning development. Copyright © 2017 Elsevier Inc. All rights reserved.

Process and circuiting arrangement for the conversion of analog signals to digital signals and digital signals to analog signals

International Nuclear Information System (INIS)

Wintzer, K.

1977-01-01

Process for analog-to-digital and digital-to-analog conversion in telecommunication systems whose outstations each have an analog transmitter and an analog receiver. The invention illustrates a method of reducing the power demand of the converters at times when no conversion processes take place. (RW) [de

Analogies and the 5E Model

Science.gov (United States)

Orgill, Mary Kay; Thomas, Megan

2007-01-01

Science classes are full of abstract or challenging concepts that are easier to understand if an analogy is used to illustrate the points. Effective analogies motivate students, clarify students' thinking, help students overcome misconceptions, and give students ways to visualize abstract concepts. When they are used appropriately, analogies can…

How Analogy Drives Physics

International Nuclear Information System (INIS)

Hofstadter, Doug

2004-01-01

Many new ideas in theoretical physics come from analogies to older ideas in physics. For instance, the abstract notion of 'isospin' (or isotopic spin) originated in the prior concept of 'spin' (quantized angular momentum); likewise, the concept of 'phonon' (quantum of sound, or quantized collective excitation of a crystal) was based on the prior concept of 'photon' (quantum of light, or quantized element of the electromagnetic field). But these two examples, far from being exceptions, in fact represent the bread and butter of inventive thinking in physics. In a nutshell, intraphysics analogy-making -- borrowing by analogy with something already known in another area of physics -- is central to the progress of physics. The aim of this talk is to reveal the pervasiveness -- indeed, the indispensability -- of this kind of semi-irrational, wholly intuitive type of thinking (as opposed to more deductive mathematical inference) in the mental activity known as 'doing physics'. Speculations as to why wild analogical leaps are so crucial to the act of discovery in physics (as opposed to other disciplines) will be offered.

Component Processes in Analogical Reasoning

Science.gov (United States)

Sternberg, Robert J.

1977-01-01

Describes alternative theoretical positions regarding (a) the component information processes used in analogical reasoning and (b) strategies for combining these processes. Also presents results from three experiments on analogical reasoning. (Author/RK)

Is the link from working memory to analogy causal? No analogy improvements following working memory training gains.

Directory of Open Access Journals (Sweden)

J Elizabeth Richey

Full Text Available Analogical reasoning has been hypothesized to critically depend upon working memory through correlational data, but less work has tested this relationship through experimental manipulation. An opportunity for examining the connection between working memory and analogical reasoning has emerged from the growing, although somewhat controversial, body of literature suggests complex working memory training can sometimes lead to working memory improvements that transfer to novel working memory tasks. This study investigated whether working memory improvements, if replicated, would increase analogical reasoning ability. We assessed participants' performance on verbal and visual analogy tasks after a complex working memory training program incorporating verbal and spatial tasks. Participants' improvements on the working memory training tasks transferred to other short-term and working memory tasks, supporting the possibility of broad effects of working memory training. However, we found no effects on analogical reasoning. We propose several possible explanations for the lack of an impact of working memory improvements on analogical reasoning.

Is the link from working memory to analogy causal? No analogy improvements following working memory training gains.

Science.gov (United States)

Richey, J Elizabeth; Phillips, Jeffrey S; Schunn, Christian D; Schneider, Walter

2014-01-01

Analogical reasoning has been hypothesized to critically depend upon working memory through correlational data, but less work has tested this relationship through experimental manipulation. An opportunity for examining the connection between working memory and analogical reasoning has emerged from the growing, although somewhat controversial, body of literature suggests complex working memory training can sometimes lead to working memory improvements that transfer to novel working memory tasks. This study investigated whether working memory improvements, if replicated, would increase analogical reasoning ability. We assessed participants' performance on verbal and visual analogy tasks after a complex working memory training program incorporating verbal and spatial tasks. Participants' improvements on the working memory training tasks transferred to other short-term and working memory tasks, supporting the possibility of broad effects of working memory training. However, we found no effects on analogical reasoning. We propose several possible explanations for the lack of an impact of working memory improvements on analogical reasoning.

Is the Link from Working Memory to Analogy Causal? No Analogy Improvements following Working Memory Training Gains

Science.gov (United States)

Richey, J. Elizabeth; Phillips, Jeffrey S.; Schunn, Christian D.; Schneider, Walter

2014-01-01

Analogical reasoning has been hypothesized to critically depend upon working memory through correlational data [1], but less work has tested this relationship through experimental manipulation [2]. An opportunity for examining the connection between working memory and analogical reasoning has emerged from the growing, although somewhat controversial, body of literature suggests complex working memory training can sometimes lead to working memory improvements that transfer to novel working memory tasks. This study investigated whether working memory improvements, if replicated, would increase analogical reasoning ability. We assessed participants’ performance on verbal and visual analogy tasks after a complex working memory training program incorporating verbal and spatial tasks [3], [4]. Participants’ improvements on the working memory training tasks transferred to other short-term and working memory tasks, supporting the possibility of broad effects of working memory training. However, we found no effects on analogical reasoning. We propose several possible explanations for the lack of an impact of working memory improvements on analogical reasoning. PMID:25188356

Beginning analog electronics through projects

CERN Document Server

Singmin, Andrew

2001-01-01

Analog electronics is the simplest way to start a fun, informative, learning program. Beginning Analog Electronics Through Projects, Second Edition was written with the needs of beginning hobbyists and students in mind. This revision of Andrew Singmin's popular Beginning Electronics Through Projects provides practical exercises, building techniques, and ideas for useful electronics projects. Additionally, it features new material on analog and digital electronics, and new projects for troubleshooting test equipment.Published in the tradition of Beginning Electronics Through Projects an

Real-time compression of analog-to-digital converter outputs

International Nuclear Information System (INIS)

Okumura, Haruhiko

1997-01-01

We describe a fast lossless data compression algorithm suitable for digitized data taken at regular time intervals, such as outputs from analog-to-digital converters (ADCs). It is designed on the assumptions that the present value can be predicted approximately from the past values, and that the distribution of the prediction error is approximately Gaussian with zero mean and small and slowly changing standard deviation. Unlike many offline compression tools such as LHA and gzip, our algorithm does not need future values to encode the present value. This property is important for real-time transmission of compressed data on the network. The algorithm is to be integrated into our data acquisition system for the Large Helical Device (LHD) experiments at the National Institute for Fusion Science (NIFS). (author)

Analog circuit design art, science, and personalities

CERN Document Server

Williams, Jim

1991-01-01

Analog Circuit Design: Art, Science, and Personalities discusses the many approaches and styles in the practice of analog circuit design. The book is written in an informal yet informative manner, making it easily understandable to those new in the field. The selection covers the definition, history, current practice, and future direction of analog design; the practice proper; and the styles in analog circuit design. The book also includes the problems usually encountered in analog circuit design; approach to feedback loop design; and other different techniques and applications. The text is

Synthetic Analogs of Phospholipid Metabolites as Antimalarials.

Science.gov (United States)

1979-07-01

phosphatidic acid analogs containing ether and phosphonate groups; completely non- hydrolyzable lecithin analogs containing phosphinate and ether groups...substance is a completely non- hydrolyzable analog of lecithin containing ether and phosphonate moieties instead of the normally labile carboxylic and...and also ant-i-phospholipase C (clostridial enzyme) activity. This substance Is a completely non- hydrolyzable analog of lecithin containing ether

FGF growth factor analogs

Science.gov (United States)

Zamora, Paul O [Gaithersburg, MD; Pena, Louis A [Poquott, NY; Lin, Xinhua [Plainview, NY; Takahashi, Kazuyuki [Germantown, MD

2012-07-24

The present invention provides a fibroblast growth factor heparin-binding analog of the formula: ##STR00001## where R.sub.1, R.sub.2, R.sub.3, R.sub.4, R.sub.5, X, Y and Z are as defined, pharmaceutical compositions, coating compositions and medical devices including the fibroblast growth factor heparin-binding analog of the foregoing formula, and methods and uses thereof.

A framework to estimate probability of diagnosis error in NPP advanced MCR

International Nuclear Information System (INIS)

Kim, Ar Ryum; Kim, Jong Hyun; Jang, Inseok; Seong, Poong Hyun

2018-01-01

Highlights: •As new type of MCR has been installed in NPPs, the work environment is considerably changed. •A new framework to estimate operators’ diagnosis error probabilities should be proposed. •Diagnosis error data were extracted from the full-scope simulator of the advanced MCR. •Using Bayesian inference, a TRC model was updated for use in advanced MCR. -- Abstract: Recently, a new type of main control room (MCR) has been adopted in nuclear power plants (NPPs). The new MCR, known as the advanced MCR, consists of digitalized human-system interfaces (HSIs), computer-based procedures (CPS), and soft controls while the conventional MCR includes many alarm tiles, analog indicators, hard-wired control devices, and paper-based procedures. These changes significantly affect the generic activities of the MCR operators, in relation to diagnostic activities. The aim of this paper is to suggest a framework to estimate the probabilities of diagnosis errors in the advanced MCR by updating a time reliability correlation (TRC) model. Using Bayesian inference, the TRC model was updated with the probabilities of diagnosis errors. Here, the diagnosis error data were collected from a full-scope simulator of the advanced MCR. To do this, diagnosis errors were determined based on an information processing model and their probabilities were calculated. However, these calculated probabilities of diagnosis errors were largely affected by context factors such as procedures, HSI, training, and others, known as PSFs (Performance Shaping Factors). In order to obtain the nominal diagnosis error probabilities, the weightings of PSFs were also evaluated. Then, with the nominal diagnosis error probabilities, the TRC model was updated. This led to the proposal of a framework to estimate the nominal probabilities of diagnosis errors in the advanced MCR.

Structure problems in the analog computation

International Nuclear Information System (INIS)

Braffort, P.L.

1957-01-01

The recent mathematical development showed the importance of elementary structures (algebraic, topological, etc.) in abeyance under the great domains of classical analysis. Such structures in analog computation are put in evidence and possible development of applied mathematics are discussed. It also studied the topological structures of the standard representation of analog schemes such as additional triangles, integrators, phase inverters and functions generators. The analog method gives only the function of the variable: time, as results of its computations. But the course of computation, for systems including reactive circuits, introduces order structures which are called 'chronological'. Finally, it showed that the approximation methods of ordinary numerical and digital computation present the same structure as these analog computation. The structure analysis permits fruitful comparisons between the several domains of applied mathematics and suggests new important domains of application for analog method. (M.P.)

Molecular modeling of fentanyl analogs

Directory of Open Access Journals (Sweden)

LJILJANA DOSEN-MICOVIC

2004-11-01

Full Text Available Fentanyl is a highly potent and clinically widely used narcotic analgesic. A large number of its analogs have been synthesized, some of which (sufentanil and alfentanyl are also in clinical use. Theoretical studies, in recent years, afforded a better understanding of the structure-activity relationships of this class of opiates and allowed insight into the molecular mechanism of the interactions of fentanyl analogs with their receptors. An overview of the current computational techniques for modeling fentanyl analogs, their receptors and ligand-receptor interactions is presented in this paper.

Terrestrial Analogs to Mars

Science.gov (United States)

Farr, T. G.; Arcone, S.; Arvidson, R. W.; Baker, V.; Barlow, N. G.; Beaty, D.; Bell, M. S.; Blankenship, D. D.; Bridges, N.; Briggs, G.; Bulmer, M.; Carsey, F.; Clifford, S. M.; Craddock, R. A.; Dickerson, P. W.; Duxbury, N.; Galford, G. L.; Garvin, J.; Grant, J.; Green, J. R.; Gregg, T. K. P.; Guinness, E.; Hansen, V. L.; Hecht, M. H.; Holt, J.; Howard, A.; Keszthelyi, L. P.; Lee, P.; Lanagan, P. D.; Lentz, R. C. F.; Leverington, D. W.; Marinangeli, L.; Moersch, J. E.; Morris-Smith, P. A.; Mouginis-Mark, P.; Olhoeft, G. R.; Ori, G. G.; Paillou, P.; Reilly, J. F., II; Rice, J. W., Jr.; Robinson, C. A.; Sheridan, M.; Snook, K.; Thomson, B. J.; Watson, K.; Williams, K.; Yoshikawa, K.

2002-08-01

It is well recognized that interpretations of Mars must begin with the Earth as a reference. The most successful comparisons have focused on understanding geologic processes on the Earth well enough to extrapolate to Mars' environment. Several facets of terrestrial analog studies have been pursued and are continuing. These studies include field workshops, characterization of terrestrial analog sites, instrument tests, laboratory measurements (including analysis of Martian meteorites), and computer and laboratory modeling. The combination of all these activities allows scientists to constrain the processes operating in specific terrestrial environments and extrapolate how similar processes could affect Mars. The Terrestrial Analogs for Mars Community Panel has considered the following two key questions: (1) How do terrestrial analog studies tie in to the Mars Exploration Payload Assessment Group science questions about life, past climate, and geologic evolution of Mars, and (2) How can future instrumentation be used to address these questions. The panel has considered the issues of data collection, value of field workshops, data archiving, laboratory measurements and modeling, human exploration issues, association with other areas of solar system exploration, and education and public outreach activities.

Expert analogy use in a naturalistic setting

Science.gov (United States)

Kretz, Donald R.; Krawczyk, Daniel C.

2014-01-01

The use of analogy is an important component of human cognition. The type of analogy we produce and communicate depends heavily on a number of factors, such as the setting, the level of domain expertise present, and the speaker's goal or intent. In this observational study, we recorded economics experts during scientific discussion and examined the categorical distance and structural depth of the analogies they produced. We also sought to characterize the purpose of the analogies that were generated. Our results supported previous conclusions about the infrequency of superficial similarity in subject-generated analogs, but also showed that distance and depth characteristics were more evenly balanced than in previous observational studies. This finding was likely due to the nature of the goals of the participants, as well as the broader nature of their expertise. An analysis of analogical purpose indicated that the generation of concrete source examples of more general target concepts was most prevalent. We also noted frequent instances of analogies intended to form visual images of source concepts. Other common purposes for analogies were the addition of colorful speech, inclusion (i.e., subsumption) of a target into a source concept, or differentiation between source and target concepts. We found no association between depth and either of the other two characteristics, but our findings suggest a relationship between purpose and distance; i.e., that visual imagery typically entailed an outside-domain source whereas exemplification was most frequently accomplished using within-domain analogies. Overall, we observed a rich and diverse set of spontaneously produced analogical comparisons. The high degree of expertise within the observed group along with the richly comparative nature of the economics discipline likely contributed to this analogical abundance. PMID:25505437

Expert Analogy Use in a Naturalistic Setting

Directory of Open Access Journals (Sweden)

Donald R Kretz

2014-11-01

Full Text Available The use of analogy is an important component of human cognition. The type of analogy we produce and communicate depends heavily on a number of factors, such as the setting, the level of domain expertise present, and the speaker’s goal or intent. In this observational study, we recorded economics experts during scientific discussion and examined the categorical distance and structural depth of the analogies they produced. We also sought to characterize the purpose of the analogies that were generated. Our results supported previous conclusions about the infrequency of superficial similarity in subject-generated analogs, but also showed that distance and depth characteristics were more evenly balanced than in previous observational studies. This finding was likely due to the nature of the goals of the participants, as well as the broader nature of their expertise. An analysis of analogical purpose indicated that the generation of concrete source examples of more general target concepts was most prevalent. We also noted frequent instances of analogies intended to form visual images of source concepts. Other common purposes for analogies were the addition of colorful speech, inclusion (i.e., subsumption of a target into a source concept, or differentiation between source and target concepts. We found no association between depth and either of the other two characteristics, but our findings suggest a relationship between purpose and distance; i.e., that visual imagery typically entailed an outside-domain source whereas exemplification was most frequently accomplished using within-domain analogies. Overall, we observed a rich and diverse set of spontaneously produced analogical comparisons. The high degree of expertise within the observed group along with the richly comparative nature of the economics discipline likely contributed to this analogical abundance.

A bilateral frontoparietal network underlies visuospatial analogical reasoning.

Science.gov (United States)

Watson, Christine E; Chatterjee, Anjan

2012-02-01

Our ability to reason by analogy facilitates problem solving and allows us to communicate ideas efficiently. In this study, we examined the neural correlates of analogical reasoning and, more specifically, the contribution of rostrolateral prefrontal cortex (RLPFC) to reasoning. This area of the brain has been hypothesized to integrate relational information, as in analogy, or the outcomes of subgoals, as in multi-tasking and complex problem solving. Using fMRI, we compared visuospatial analogical reasoning to a control task that was as complex and difficult as the analogies and required the coordination of subgoals but not the integration of relations. We found that analogical reasoning more strongly activated bilateral RLPFC, suggesting that anterior prefrontal cortex is preferentially recruited by the integration of relational knowledge. Consistent with the need for inhibition during analogy, bilateral, and particularly right, inferior frontal gyri were also more active during analogy. Finally, greater activity in bilateral inferior parietal cortex during the analogy task is consistent with recent evidence for the neural basis of spatial relation knowledge. Together, these findings indicate that a network of frontoparietal areas underlies analogical reasoning; we also suggest that hemispheric differences may emerge depending on the visuospatial or verbal/semantic nature of the analogies. Copyright © 2011 Elsevier Inc. All rights reserved.

Population structure and accompanying biota of the snail Turbo (Callopoma funiculosus (Gastropoda: Turbinidae, on Socorro Island, Revillagigedo Archipelago, Mexico

Directory of Open Access Journals (Sweden)

Oscar E Holguin Quiñones

2006-12-01

Full Text Available The porcelain snail, Turbo funiculosus, is a potential fishery resource that almost has not been studied or used commercially. In March of 1992, we sampled T. funiculosus in Bahía Binners and Bahía Blanca, Socorro Island, Revillagigedo Archipelago, using 25 m² quadrants. We found that total length varies between 3.0 and 85 mm, proportional weight between 3.0 and 228 g, and density between 6.21 and 9.87 ind/m². The largest organisms (over 50 mm contain 30.6 % of soft parts. Porcelain snail populations remain unexploited on Revillagedo Archipelago and could be a potential resource under an adequate management strategy. Rev. Biol. Trop. 54 (4: 1079-1084. Epub 2006 Dec. 15.El caracol porcelana, Turbo funiculosus, es un recurso pesquero potencial que casi no ha sido estudiado ni se ha utilizado comercialmente. En marzo de 1992, se realizó un muestreo de T. funiculosus en Bahía Binners y Bahía Blanca, isla Socorro, archipiélago Revillagigedo, empleando cuadrantes de 25 m2. Se encontraron variaciones en la longitud total entre 3.0 y 85 mm, el peso proporcional entre 3.0 y 228 g, y la densidad entre 6.21 y 9.87 ind/m2. Los organismos de mayor tamaño (más de 50 mm contienen 30.6 % de partes suaves. Las poblaciones del caracol porcelana siguen siendo inexplotadas en el archipiélago Revillagedo y podrían ser un recurso potencial de la industria pesquera bajo un adecuado plan de manejo.

Usefulness of dual echo volumetric isotropic turbo spin echo acquisition (VISTA) in MR imaging of the temporomandibular joint

International Nuclear Information System (INIS)

Sugimori, Yuko; Tanaka, Shigeko; Naito, Yukari; Nishimura, Tetsuya; Yamamoto, Akira; Miki, Yukio; Ohfuji, Satoko; Katsumata, Yasutomo

2013-01-01

We investigated the ability to detect the articular disk and joint effusion of the temporomandibular joint (TMJ) of a method of dual echo volumetric isotropic turbo spin echo acquisition (DE-VISTA) additional fusion images (AFI). DE-VISTA was performed in the 26 TMJ of 13 volunteers and 26 TMJ of 13 patients. Two-dimensional (2D) dual echo turbo spin echo was performed in the 26 TMJ of 13 volunteers. On a workstation, we added proton density-weighted images (PDWI) and T 2 weighted images (T 2 WI) of the DE-VISTA per voxel to reconstruct DE-VISTA-AFI. Two radiologists reviewed these images visually and quantitatively. Visual evaluation of the articular disk was equivalent between DE-VISTA-AFI and 2D-PDWI. The sliding thin-slab multiplanar reformation (MPR) method of DE-VISTA-AFI could detect all articular disks. The ratio of contrast (CR) of adipose tissue by the articular disk to that of the articular disk itself was significantly higher in DE-VISTA-AFI than DE-VISTA-PDWI (P 2 WI but in only 3 of those joints in 2D-T 2 WI. The CR of joint effusion to adipose tissue on DE-VISTA-AFI did not differ significantly from that on DE-VISTA-PDWI. However, using DE-VISTA-T 2 WI in addition to DE-VISTA-PDWI, we could visually identify joint effusion on DE-VISTA-AFI that could not be identified on DE-VISTA-PDWI alone. DE-VISTA-AFI can depict the articular disk and a small amount of joint effusion by the required plane of MPR using the sliding thin-slab MPR method. (author)

Neural correlates of creativity in analogical reasoning.

Science.gov (United States)

Green, Adam E; Kraemer, David J M; Fugelsang, Jonathan A; Gray, Jeremy R; Dunbar, Kevin N

2012-03-01

Brain-based evidence has implicated the frontal pole of the brain as important for analogical mapping. Separately, cognitive research has identified semantic distance as a key determinant of the creativity of analogical mapping (i.e., more distant analogies are generally more creative). Here, we used functional magnetic resonance imaging to assess brain activity during an analogy generation task in which we varied the semantic distance of analogical mapping (as derived quantitatively from a latent semantic analysis). Data indicated that activity within an a priori region of interest in left frontopolar cortex covaried parametrically with increasing semantic distance, even after removing effects of task difficulty. Results implicate increased recruitment of frontopolar cortex as a mechanism for integrating semantically distant information to generate solutions in creative analogical reasoning. 2012 APA, all rights reserved

Action errors, error management, and learning in organizations.

Science.gov (United States)

Frese, Michael; Keith, Nina

2015-01-03

Every organization is confronted with errors. Most errors are corrected easily, but some may lead to negative consequences. Organizations often focus on error prevention as a single strategy for dealing with errors. Our review suggests that error prevention needs to be supplemented by error management--an approach directed at effectively dealing with errors after they have occurred, with the goal of minimizing negative and maximizing positive error consequences (examples of the latter are learning and innovations). After defining errors and related concepts, we review research on error-related processes affected by error management (error detection, damage control). Empirical evidence on positive effects of error management in individuals and organizations is then discussed, along with emotional, motivational, cognitive, and behavioral pathways of these effects. Learning from errors is central, but like other positive consequences, learning occurs under certain circumstances--one being the development of a mind-set of acceptance of human error.

Using Visual Analogies To Teach Introductory Statistical Concepts

Directory of Open Access Journals (Sweden)

Jessica S. Ancker

2017-07-01

Full Text Available Introductory statistical concepts are some of the most challenging to convey in quantitative literacy courses. Analogies supplemented by visual illustrations can be highly effective teaching tools. This literature review shows that to exploit the power of analogies, teachers must select analogies familiar to the audience, explicitly link the analog with the target concept, and avert misconceptions by explaining where the analogy fails. We provide guidance for instructors and a series of visual analogies for use in teaching medical and health statistics.

DINEOF reconstruction of clouded images including error maps – application to the Sea-Surface Temperature around Corsican Island

Directory of Open Access Journals (Sweden)

J.-M. Beckers

2006-01-01

Full Text Available We present an extension to the Data INterpolating Empirical Orthogonal Functions (DINEOF technique which allows not only to fill in clouded images but also to provide an estimation of the error covariance of the reconstruction. This additional information is obtained by an analogy with optimal interpolation. It is shown that the error fields can be obtained with a clever rearrangement of calculations at a cost comparable to that of the interpolation itself. The method is presented on the reconstruction of sea-surface temperature in the Ligurian Sea and around the Corsican Island (Mediterranean Sea, including the calculation of inter-annual variability of average surface values and their expected errors. The application shows that the error fields are not only able to reflect the data-coverage structure but also the covariances of the physical fields.

A Calibration Method for Nonlinear Mismatches in M-Channel Time-Interleaved Analog-to-Digital Converters Based on Hadamard Sequences

Directory of Open Access Journals (Sweden)

Husheng Liu

2016-11-01

Full Text Available The time-interleaved analog-to-digital converter (TIADC is an architecture used to achieve a high sampling rate and high dynamic performance. However, estimation and compensation methods are required to maintain the dynamic performance of the constituent analog-to-digital converters (ADCs due to channel mismatches. This paper proposes a blind adaptive method to calibrate the nonlinear mismatches in M-channel TIADCs (M-TIADCs. The nonlinearity-induced error signal is reconstructed by the proposed multiplier Hadamard transform (MHT structure, and the nonlinear parameters are estimated by the filtered-X least-mean square (FxLMS algorithm. The performance of cascade calibration is also analyzed. The numerical simulation results show that the proposed method consumes much less hardware resources while maintaining the calibration performance.

Modeling coherent errors in quantum error correction

Science.gov (United States)

Greenbaum, Daniel; Dutton, Zachary

2018-01-01

Analysis of quantum error correcting codes is typically done using a stochastic, Pauli channel error model for describing the noise on physical qubits. However, it was recently found that coherent errors (systematic rotations) on physical data qubits result in both physical and logical error rates that differ significantly from those predicted by a Pauli model. Here we examine the accuracy of the Pauli approximation for noise containing coherent errors (characterized by a rotation angle ɛ) under the repetition code. We derive an analytic expression for the logical error channel as a function of arbitrary code distance d and concatenation level n, in the small error limit. We find that coherent physical errors result in logical errors that are partially coherent and therefore non-Pauli. However, the coherent part of the logical error is negligible at fewer than {ε }-({dn-1)} error correction cycles when the decoder is optimized for independent Pauli errors, thus providing a regime of validity for the Pauli approximation. Above this number of correction cycles, the persistent coherent logical error will cause logical failure more quickly than the Pauli model would predict, and this may need to be combated with coherent suppression methods at the physical level or larger codes.

MENINGKATKAN HASIL BELAJAR KIDS ATLETIK LEMPAR TURBO MELALUI MODIFIKASI PERMAINAN BOLA BEREKOR BAGI SISWA KELAS 5 SDN 1 SUKOREJO TAHUN AJARAN 2013/2014

Directory of Open Access Journals (Sweden)

Hasan Khoerudin

2015-03-01

Full Text Available The purpose of this study was to determine the improvement of learning outcomes athletic kids throwing turbo through modification of the game ball tailed for the Grade 5 Elementary School 1 Sukorejo academic year 2013/2014 . This study uses action research. In the implementation consists of two cycles. The instrument used in this study is the test performance of students, student observation sheet, and a written test. Based on the results, the percentage of mastery learning in the first cycle, psychomotor aspects of 32.4 %, 76.5 % affective aspects, cognitive aspects of 94.2 %, and mastery learning students classically 64.7 % of the total number of students. In the second cycle psychomotor aspects of 76.5 %, 88.2 % affective aspects, cognitive aspects of 97.1 %, and mastery learning students classically 85.3 % of the total number of students. In the present study showed an increase in student learning in classical completeness by 20.6 %, from 64.7 % to the first cycle to 85.3 % in the second cycle. Based on the above results, it was concluded that the modification of the game ball tailed in teaching athletic kids throwing turbo can improve student learning outcomes the Grade 5 Elementary School 1 Sukorejo academic year 2013/2014.

Errors in causal inference: an organizational schema for systematic error and random error.

Science.gov (United States)

Suzuki, Etsuji; Tsuda, Toshihide; Mitsuhashi, Toshiharu; Mansournia, Mohammad Ali; Yamamoto, Eiji

2016-11-01

To provide an organizational schema for systematic error and random error in estimating causal measures, aimed at clarifying the concept of errors from the perspective of causal inference. We propose to divide systematic error into structural error and analytic error. With regard to random error, our schema shows its four major sources: nondeterministic counterfactuals, sampling variability, a mechanism that generates exposure events and measurement variability. Structural error is defined from the perspective of counterfactual reasoning and divided into nonexchangeability bias (which comprises confounding bias and selection bias) and measurement bias. Directed acyclic graphs are useful to illustrate this kind of error. Nonexchangeability bias implies a lack of "exchangeability" between the selected exposed and unexposed groups. A lack of exchangeability is not a primary concern of measurement bias, justifying its separation from confounding bias and selection bias. Many forms of analytic errors result from the small-sample properties of the estimator used and vanish asymptotically. Analytic error also results from wrong (misspecified) statistical models and inappropriate statistical methods. Our organizational schema is helpful for understanding the relationship between systematic error and random error from a previously less investigated aspect, enabling us to better understand the relationship between accuracy, validity, and precision. Copyright © 2016 Elsevier Inc. All rights reserved.

CMOS analog circuit design

CERN Document Server

Allen, Phillip E

1987-01-01

This text presents the principles and techniques for designing analog circuits to be implemented in a CMOS technology. The level is appropriate for seniors and graduate students familiar with basic electronics, including biasing, modeling, circuit analysis, and some familiarity with frequency response. Students learn the methodology of analog integrated circuit design through a hierarchically-oriented approach to the subject that provides thorough background and practical guidance for designing CMOS analog circuits, including modeling, simulation, and testing. The authors' vast industrial experience and knowledge is reflected in the circuits, techniques, and principles presented. They even identify the many common pitfalls that lie in the path of the beginning designer--expert advice from veteran designers. The text mixes the academic and practical viewpoints in a treatment that is neither superficial nor overly detailed, providing the perfect balance.

An Empirical State Error Covariance Matrix Orbit Determination Example

Science.gov (United States)

Frisbee, Joseph H., Jr.

2015-01-01

is suspect. In its most straight forward form, the technique only requires supplemental calculations to be added to existing batch estimation algorithms. In the current problem being studied a truth model making use of gravity with spherical, J2 and J4 terms plus a standard exponential type atmosphere with simple diurnal and random walk components is used. The ability of the empirical state error covariance matrix to account for errors is investigated under four scenarios during orbit estimation. These scenarios are: exact modeling under known measurement errors, exact modeling under corrupted measurement errors, inexact modeling under known measurement errors, and inexact modeling under corrupted measurement errors. For this problem a simple analog of a distributed space surveillance network is used. The sensors in this network make only range measurements and with simple normally distributed measurement errors. The sensors are assumed to have full horizon to horizon viewing at any azimuth. For definiteness, an orbit at the approximate altitude and inclination of the International Space Station is used for the study. The comparison analyses of the data involve only total vectors. No investigation of specific orbital elements is undertaken. The total vector analyses will look at the chisquare values of the error in the difference between the estimated state and the true modeled state using both the empirical and theoretical error covariance matrices for each of scenario.

4-bit digital to analog converter using R-2R ladder and binary weighted resistors

Science.gov (United States)

Diosanto, J.; Batac, M. L.; Pereda, K. J.; Caldo, R.

2017-06-01

The use of a 4-bit digital-to-analog converter using two methods; Binary Weighted Resistors and R-2R Ladder is designed and presented in this paper. The main components that were used in constructing both circuits were different resistor values, operational amplifier (LM741) and single pole double throw switches. Both circuits were designed using MULTISIM software to be able to test the circuit for its ideal application and FRITZING software for the layout designing and fabrication to the printed circuit board. The implementation of both systems in an actual circuit benefits in determining and comparing the advantages and disadvantages of each. It was realized that the binary weighted circuit is more efficient DAC, having lower percentage error of 0.267% compared to R-2R ladder circuit which has a minimum of percentage error of 4.16%.

Frontopolar cortex mediates abstract integration in analogy.

Science.gov (United States)

Green, Adam E; Fugelsang, Jonathan A; Kraemer, David J M; Shamosh, Noah A; Dunbar, Kevin N

2006-06-22

Integration of abstractly similar relations during analogical reasoning was investigated using functional magnetic resonance imaging. Activation elicited by an analogical reasoning task that required both complex working memory and integration of abstractly similar relations was compared to activation elicited by a non-analogical task that required complex working memory in the absence of abstract relational integration. A left-sided region of the frontal pole of the brain (BA 9/10) was selectively active for the abstract relational integration component of analogical reasoning. Analogical reasoning also engaged a left-sided network of parieto-frontal regions. Activity in this network during analogical reasoning is hypothesized to reflect categorical alignment of individual component terms that make up analogies. This parieto-frontal network was also engaged by the complex control task, which involved explicit categorization, but not by a simpler control task, which did not involve categorization. We hypothesize that frontopolar cortex mediates abstract relational integration in complex reasoning while parieto-frontal regions mediate working memory processes, including manipulation of terms for the purpose of categorical alignment, that facilitate this integration.

The force of dissimilar analogies in bioethics.

Science.gov (United States)

Mertes, Heidi; Pennings, Guido

2011-04-01

Although analogical reasoning has long been a popular method of reasoning in bioethics, current literature does not sufficiently grasp its variety. We assert that the main shortcoming is the fact that an analogy's value is often judged on the extent of similarity between the source situation and the target situation, while in (bio)ethics, analogies are often used because of certain dissimilarities rather than in spite of them. We make a clear distinction between dissimilarities that aim to reinforce a similar approach in the source situation and the target situation and dissimilarities that aim to undermine or denounce a similar approach. The former kind of dissimilarity offers the analogy more normative force than if there were no dissimilarities present; this is often overlooked by authors who regard all relevant dissimilarities as detrimental to the analogy's strength. Another observation is that an evaluation of the normative force of an analogy cannot be made independently of moral principles or theories. Without these, one cannot select which elements in an analogy are morally relevant nor determine how they should be interpreted.

Anti-Plasmodium activity of ceramide analogs

Directory of Open Access Journals (Sweden)

Gatt Shimon

2004-12-01

Full Text Available Abstract Background Sphingolipids are key molecules regulating many essential functions in eukaryotic cells and ceramide plays a central role in sphingolipid metabolism. A sphingolipid metabolism occurs in the intraerythrocytic stages of Plasmodium falciparum and is associated with essential biological processes. It constitutes an attractive and potential target for the development of new antimalarial drugs. Methods The anti-Plasmodium activity of a series of ceramide analogs containing different linkages (amide, methylene or thiourea linkages between the fatty acid part of ceramide and the sphingoid core was investigated in culture and compared to the sphingolipid analog PPMP (d,1-threo-1-phenyl-2-palmitoylamino-3-morpholino-1-propanol. This analog is known to inhibit the parasite sphingomyelin synthase activity and block parasite development by preventing the formation of the tubovesicular network that extends from the parasitophorous vacuole to the red cell membrane and delivers essential extracellular nutrients to the parasite. Results Analogs containing methylene linkage showed a considerably higher anti-Plasmodium activity (IC50 in the low nanomolar range than PPMP and their counterparts with a natural amide linkage (IC50 in the micromolar range. The methylene analogs blocked irreversibly P. falciparum development leading to parasite eradication in contrast to PPMP whose effect is cytostatic. A high sensitivity of action towards the parasite was observed when compared to their effect on the human MRC-5 cell growth. The toxicity towards parasites did not correlate with the inhibition by methylene analogs of the parasite sphingomyelin synthase activity and the tubovesicular network formation, indicating that this enzyme is not their primary target. Conclusions It has been shown that ceramide analogs were potent inhibitors of P. falciparum growth in culture. Interestingly, the nature of the linkage between the fatty acid part and the

The future of vitamin D analogs

Directory of Open Access Journals (Sweden)

Carlien eLeyssens

2014-04-01

Full Text Available The active form of vitamin D3, 1,25-dihydroxyvitamin D3, is a major regulator of bone and calcium homeostasis. In addition, this hormone also inhibits the proliferation and stimulates the differentiation of normal as well as malignant cells. Supraphysiological doses of 1,25-dihydroxyvitamin D3 are required to reduce cancer cell proliferation. However, these doses will lead in vivo to calcemic side effects such as hypercalcemia and hypercalciuria. During the last 25 years, many structural analogs of 1,25-dihydroxyvitamin D3 have been synthesized by the introduction of chemical modifications in the A-ring, central CD-ring region or side chain of 1,25-dihydroxyvitamin D3 in the hope to find molecules with a clear dissociation between the beneficial antiproliferative effects and adverse calcemic side effects. One example of such an analog with a good dissociation ratio is calcipotriol (DaivonexR, which is clinically used to treat the hyperproliferative skin disease psoriasis. Other vitamin D analogs were clinically approved for the treatment of osteoporosis or secondary hyperparathyroidism. No vitamin D analog is currently used in the clinic for the treatment of cancer although several analogs have been shown to be potent drugs in animal models of cancer. Omics studies as well as in vitro cell biological experiments unraveled basic mechanisms involved in the antineoplastic effects of vitamin D and its analogs. 1,25-dihydroxyvitamin D3 and analogs act in a cell type- and tissue-specific manner. Moreover, a blockade in the transition of the G0/1 towards S phase of the cell cycle, induction of apoptosis, inhibition of migration and invasion of tumor cells together with effects on angiogenesis and inflammation have been implicated in the pleiotropic effects of 1,25-dihydroxyvitamin D3 and its analogs. In this review we will give an overview of the action of vitamin D analogs in tumor cells and look forward how these compounds could be introduced in the

Enhancing programming logic thinking using analogy mapping

Science.gov (United States)

Sukamto, R. A.; Megasari, R.

2018-05-01

Programming logic thinking is the most important competence for computer science students. However, programming is one of the difficult subject in computer science program. This paper reports our work about enhancing students' programming logic thinking using Analogy Mapping for basic programming subject. Analogy Mapping is a computer application which converts source code into analogies images. This research used time series evaluation and the result showed that Analogy Mapping can enhance students' programming logic thinking.

Gemini analogs of vitamin D.

Science.gov (United States)

Pazos, Gonzalo; Rivadulla, Marcos L; Pérez-García, Xenxo; Gandara, Zoila; Pérez, Manuel

2014-01-01

The Gemini analogs are the last significant contribution to the family of vitamin D derivatives in medicine, for the treatment of cancer. The first Gemini analog was characterized by two symmetric side chains at C-20. Following numerous modifications, the most active analog bears a C-23-triple bond, C-26, 27- hexafluoro substituents on one side chain and a terminal trideuteromethylhydroxy group on the other side chain. This progression was possible due to improvements in the synthetic methods for the preparation of these derivatives, which allowed for increasing molecular complexity and complete diastereoselective control at C-20 and the substituted sidechains.

The Habitat of Yellow Mouth Turban Turbo Chrysostomus, Linnaeus, 1758

Science.gov (United States)

Soekendarsi, E.

2018-03-01

In general, yellow mouth turban snail Turbo chrysostomus L. 1758 was found in intertidal and coral reef area. This animal is active at night (nocturnal) and settles the coral reef-flats area to do its activity as substrate. In doing its activity, yellow mouth turban snail can be found in the depth of 50 cm until 4 m of tidal area. The adult yellow mouth turban snails are found in great number at intertidal area’s border and at coastal area of coral reef-flats. Methodology that was used in this study is visual analysis (descriptive method), and divided into two parameters which were observed, i.e. abiotic and biotic. Abiotic components that were measured are; Oxygen (ppm), pH, Water Temperature (°C), Salinity (ppm), Ammonia (mg/L), Nitrate (mg/L), Nitrite (mg/L), and Calsium Carbonat (mg/L).Whereas, biotic components that were measured are; substrates, seaweeds, other organisms, and epilithon. The observation’s result of yellow mouth turban snail’s environmental condition showed: abiotic condition of the waters consists of oxygen 3-5 ppm, seawater pH 7-8, seawater temperature 23-26°C, and the salinity of 32-33 ppm. The Habitat of yellow mouth turban snail settled the reef-flats area that is overgrown covered by seaweed Sargassum sp. as the place to do its activity.

A fast multichannel analog storage system

International Nuclear Information System (INIS)

Freytag, D.R.

1983-01-01

A Multichannel Analog Storage System based on a commercial 32-channel parallel in/serial out (PISO) analog shift register is described. The basic unit is a single width CAMAC module containing 512 analog cells and the associated logic for data storage and subsequent readout. At sampling rates of up to 30 MHz the signals are strobed directly into the PISO. At higher rates signals are strobed into a fast presampling stage and subsequently transferred in block form into an array of PISO's. Sampling rates of 300 MHz have been achieved with the present device and 1000 MHz are possible with improved signal drivers. The system is well suited for simultaneous handling of many signal channels with moderate numbers of samples in each channel. RMS noise over full scale signal has been measured as 1:3000 (approx. =11 bit). However, nonlinearities in the response and differences in sensitivity of the analog cells require an elaborate calibration system in order to realize 11 bit accuracy for the analog information

Atheism and Analogy: Aquinas Against the Atheists

OpenAIRE

Linford, Daniel J.

2014-01-01

In the 13th century, Thomas Aquinas developed two models for how humans may speak of God - either by the analogy of proportion or by the analogy of proportionality. Aquinas's doctrines initiated a theological debate concerning analogy that spanned several centuries. In the 18th century, there appeared two closely related arguments for atheism which both utilized analogy for their own purposes. In this thesis, I show that one argument, articulated by the French materialist Paul-Henri Thiry Bar...

Analog filters in nanometer CMOS

CERN Document Server

Uhrmann, Heimo; Zimmermann, Horst

2014-01-01

Starting from the basics of analog filters and the poor transistor characteristics in nanometer CMOS 10 high-performance analog filters developed by the authors in 120 nm and 65 nm CMOS are described extensively. Among them are gm-C filters, current-mode filters, and active filters for system-on-chip realization for Bluetooth, WCDMA, UWB, DVB-H, and LTE applications. For the active filters several operational amplifier designs are described. The book, furthermore, contains a review of the newest state of research on low-voltage low-power analog filters. To cover the topic of the book comprehensively, linearization issues and measurement methods for the characterization of advanced analog filters are introduced in addition. Numerous elaborate illustrations promote an easy comprehension. This book will be of value to engineers and researchers in industry as well as scientists and Ph.D students at universities. The book is also recommendable to graduate students specializing on nanoelectronics, microelectronics ...

Scientific Analogies and Their Use in Teaching Science

Science.gov (United States)

Kipnis, Nahum

Analogy in science knew its successes and failures, as illustrated by examples from the eighteenth-century physics. At times, some scientists abstained from using a certain analogy on the ground that it had not yet been demonstrated. Several false discoveries in the 18th and early 19th centuries appeared to support their caution. It is now clear that such a position reflected a methodological confusion that resulted from a failure to distinguish between particular and general analogies. Considering analogy as a hierarchical structure provides a new insight into "testing an analogy". While warning science teachers of dangers associated with use of analogy, historical cases and their analysis provided here may encourage them to use analogy more extensively while avoiding misconceptions. An argument is made that the history of science may be a better guide than philosophy of science and cognitive psychology when it concerns the role of analogy in science and in teaching science for understanding.

Drawing Analogies in Environmental Education

Science.gov (United States)

Affifi, Ramsey

2014-01-01

Reconsidering the origin, process, and outcomes of analogy-making suggests practices for environmental educators who strive to disengage humans from the isolating illusions of dichotomizing frameworks. We can view analogies as outcomes of developmental processes within which human subjectivity is but an element, threading our sense of self back…

Conjecturing via Reconceived Classical Analogy

Science.gov (United States)

Lee, Kyeong-Hwa; Sriraman, Bharath

2011-01-01

Analogical reasoning is believed to be an efficient means of problem solving and construction of knowledge during the search for and the analysis of new mathematical objects. However, there is growing concern that despite everyday usage, learners are unable to transfer analogical reasoning to learning situations. This study aims at facilitating…

Spectrometric analog-to-digital converter

International Nuclear Information System (INIS)

Ormandzhiev, S.I.; Jordanov, V.T.

1988-01-01

Converter of digit-by-digit counterbalancing with slipping dial with number of channels equal to total number of states of the main digital-to-analog converter of digit-by-digit counterbalancing systems is presented. Algorithm for selection of digital-to-analog converters, which must be used by means of computer is suggested

Factores de riesgo sociales y ambientales relacionados con casos de leptospirosis de manejo ambulatorio y hospitalario, Turbo, Colombia

Directory of Open Access Journals (Sweden)

Dionisia Yusti

2013-08-01

Full Text Available Introducción. La leptospirosis es un problema de salud pública en el Urabá colombiano y poco se sabe sobre las condiciones ambientales y sociales de esta enfermedad en la región. Objetivo. Explorar algunos factores de riesgo relacionados con leptospirosis de manejo hospitalario y ambulatorio, en pacientes del municipio de Turbo durante los años 2010 y 2011. Materiales y métodos. Mediante un estudio descriptivo se exploraron factores relacionados conla exposición a Leptospira spp. (aspectos socio-demográficos, hábitos, condiciones físicas y de saneamiento de la vivienda, hacinamiento, fuentes de agua potable, presencia de roedores sinantrópicos y convivencia con animales en pacientes con leptospirosis que requirieron manejo hospitalario en el municipio de Turbo durante los años 2010 y 2011. Se utilizaron medidas estadísticas estandarizadas para estudios descriptivos. Resultados. Se encontró que el hábito de caminar descalzo en ambientes domésticos representó 4,27 (1,32-13,82 veces el riesgo para presentar leptospirosis de manejo hospitalario (p=0,012. El análisis multivariado exploratorio mostró que la presencia de fauna silvestre en las viviendas puede estar relacionada también con casos de manejo hospitalario. Este hallazgo representó 4,22 (1,13-15,72 veces el riesgo comparado con los casos ambulatorios que manifestaron no tener este tipo deanimales dentro de la vivienda (p=0,032. Conclusión. Este estudio plantea bases para diseñar e implementar intervenciones efectivas, orientadas desde el perfil de riesgos al que se exponen sus habitantes, en un área geográfica queexhibe una epidemiología dinámica de contexto complejo para leptospirosis.   doi: http://dx.doi.org/10.7705/biomedica.v33i0.1457

Preliminary thermodynamic study for an efficient turbo-blower external combustion Rankine cycle

Science.gov (United States)

Romero Gómez, Manuel; Romero Gómez, Javier; Ferreiro Garcia, Ramón; Baaliña Insua, Álvaro

2014-08-01

This research paper presents a preliminary thermodynamic study of an innovative power plant operating under a Rankine cycle fed by an external combustion system with turbo-blower (TB). The power plant comprises an external combustion system for natural gas, where the combustion gases yield their thermal energy, through a heat exchanger, to a carbon dioxide Rankine cycle operating under supercritical conditions and with quasi-critical condensation. The TB exploits the energy from the pressurised exhaust gases for compressing the combustion air. The study is focused on the comparison of the combustion system's conventional technology with that of the proposed. An energy analysis is carried out and the effect of the flue gas pressure on the efficiency and on the heat transfer in the heat exchanger is studied. The coupling of the TB results in an increase in efficiency and of the convection coefficient of the flue gas with pressure, favouring a reduced volume of the heat exchanger. The proposed innovative system achieves increases in efficiency of around 12 % as well as a decrease in the heat exchanger volume of 3/5 compared with the conventional technology without TB.

On-Board Real-Time Optimization Control for Turbo-Fan Engine Life Extending

Science.gov (United States)

Zheng, Qiangang; Zhang, Haibo; Miao, Lizhen; Sun, Fengyong

2017-11-01

A real-time optimization control method is proposed to extend turbo-fan engine service life. This real-time optimization control is based on an on-board engine mode, which is devised by a MRR-LSSVR (multi-input multi-output recursive reduced least squares support vector regression method). To solve the optimization problem, a FSQP (feasible sequential quadratic programming) algorithm is utilized. The thermal mechanical fatigue is taken into account during the optimization process. Furthermore, to describe the engine life decaying, a thermal mechanical fatigue model of engine acceleration process is established. The optimization objective function not only contains the sub-item which can get fast response of the engine, but also concludes the sub-item of the total mechanical strain range which has positive relationship to engine fatigue life. Finally, the simulations of the conventional optimization control which just consider engine acceleration performance or the proposed optimization method have been conducted. The simulations demonstrate that the time of the two control methods from idle to 99.5 % of the maximum power are equal. However, the engine life using the proposed optimization method could be surprisingly increased by 36.17 % compared with that using conventional optimization control.

Modeling of turbulent flows in cooling channels of turbo-machineries; Modelisation des ecoulements turbulents dans des canaux de refroidissement de turbomachines

Energy Technology Data Exchange (ETDEWEB)

Bidart, A.; Caltagirone, J.P.; Parneix, S. [Laboratoire MASTER-ENSCPB, 33 - Talence (France)

1997-12-31

The MASTER laboratory has been involved since several years in the creation and utilization of modeling tools for the prediction of 3-D turbulent flows and heat transfers in turbine blades in order to optimize the cooling systems of turbo-machineries. This paper describes one of the test-cases that has been used for the validation of the `Aquilon` calculation code developed in this aim. Then, the modeling performed with the `Fluent` industrial code in order to evaluate the possible improvements of the Aquilon code, is presented. (J.S.) 5 refs.

Modeling Human Error Mechanism for Soft Control in Advanced Control Rooms (ACRs)

Energy Technology Data Exchange (ETDEWEB)

Aljneibi, Hanan Salah Ali [Khalifa Univ., Abu Dhabi (United Arab Emirates); Ha, Jun Su; Kang, Seongkeun; Seong, Poong Hyun [KAIST, Daejeon (Korea, Republic of)

2015-10-15

To achieve the switch from conventional analog-based design to digital design in ACRs, a large number of manual operating controls and switches have to be replaced by a few common multi-function devices which is called soft control system. The soft controls in APR-1400 ACRs are classified into safety-grade and non-safety-grade soft controls; each was designed using different and independent input devices in ACRs. The operations using soft controls require operators to perform new tasks which were not necessary in conventional controls such as navigating computerized displays to monitor plant information and control devices. These kinds of computerized displays and soft controls may make operations more convenient but they might cause new types of human error. In this study the human error mechanism during the soft controls is studied and modeled to be used for analysis and enhancement of human performance (or human errors) during NPP operation. The developed model would contribute to a lot of applications to improve human performance (or reduce human errors), HMI designs, and operators' training program in ACRs. The developed model of human error mechanism for the soft control is based on assumptions that a human operator has certain amount of capacity in cognitive resources and if resources required by operating tasks are greater than resources invested by the operator, human error (or poor human performance) is likely to occur (especially in 'slip'); good HMI (Human-machine Interface) design decreases the required resources; operator's skillfulness decreases the required resources; and high vigilance increases the invested resources. In this study the human error mechanism during the soft controls is studied and modeled to be used for analysis and enhancement of human performance (or reduction of human errors) during NPP operation.

Modeling Human Error Mechanism for Soft Control in Advanced Control Rooms (ACRs)

International Nuclear Information System (INIS)

Aljneibi, Hanan Salah Ali; Ha, Jun Su; Kang, Seongkeun; Seong, Poong Hyun

2015-01-01

To achieve the switch from conventional analog-based design to digital design in ACRs, a large number of manual operating controls and switches have to be replaced by a few common multi-function devices which is called soft control system. The soft controls in APR-1400 ACRs are classified into safety-grade and non-safety-grade soft controls; each was designed using different and independent input devices in ACRs. The operations using soft controls require operators to perform new tasks which were not necessary in conventional controls such as navigating computerized displays to monitor plant information and control devices. These kinds of computerized displays and soft controls may make operations more convenient but they might cause new types of human error. In this study the human error mechanism during the soft controls is studied and modeled to be used for analysis and enhancement of human performance (or human errors) during NPP operation. The developed model would contribute to a lot of applications to improve human performance (or reduce human errors), HMI designs, and operators' training program in ACRs. The developed model of human error mechanism for the soft control is based on assumptions that a human operator has certain amount of capacity in cognitive resources and if resources required by operating tasks are greater than resources invested by the operator, human error (or poor human performance) is likely to occur (especially in 'slip'); good HMI (Human-machine Interface) design decreases the required resources; operator's skillfulness decreases the required resources; and high vigilance increases the invested resources. In this study the human error mechanism during the soft controls is studied and modeled to be used for analysis and enhancement of human performance (or reduction of human errors) during NPP operation

Exergy Analysis of a Subcritical Refrigeration Cycle with an Improved Impulse Turbo Expander

Directory of Open Access Journals (Sweden)

Zhenying Zhang

2014-08-01

Full Text Available The impulse turbo expander (ITE is employed to replace the throttling valve in the vapor compression refrigeration cycle to improve the system performance. An improved ITE and the corresponding cycle are presented. In the new cycle, the ITE not only acts as an expansion device with work extraction, but also serves as an economizer with vapor injection. An increase of 20% in the isentropic efficiency can be attained for the improved ITE compared with the conventional ITE owing to the reduction of the friction losses of the rotor. The performance of the novel cycle is investigated based on energy and exergy analysis. A correlation of the optimum intermediate pressure in terms of ITE efficiency is developed. The improved ITE cycle increases the exergy efficiency by 1.4%–6.1% over the conventional ITE cycle, 4.6%–8.3% over the economizer cycle and 7.2%–21.6% over the base cycle. Furthermore, the improved ITE cycle is also preferred due to its lower exergy loss.

Error begat error: design error analysis and prevention in social infrastructure projects.

Science.gov (United States)

Love, Peter E D; Lopez, Robert; Edwards, David J; Goh, Yang M

2012-09-01

Design errors contribute significantly to cost and schedule growth in social infrastructure projects and to engineering failures, which can result in accidents and loss of life. Despite considerable research that has addressed their error causation in construction projects they still remain prevalent. This paper identifies the underlying conditions that contribute to design errors in social infrastructure projects (e.g. hospitals, education, law and order type buildings). A systemic model of error causation is propagated and subsequently used to develop a learning framework for design error prevention. The research suggests that a multitude of strategies should be adopted in congruence to prevent design errors from occurring and so ensure that safety and project performance are ameliorated. Copyright © 2011. Published by Elsevier Ltd.

Relations as transformations: implications for analogical reasoning.

Science.gov (United States)

Leech, Robert; Mareschal, Denis; Cooper, Richard P

2007-07-01

We present two experiments assessing whether the size of a transformation instantiating a relation between two states of the world (e.g., shrinks) is a performance factor affecting analogical reasoning. The first experiment finds evidence of transformation size as a significant factor in adolescent analogical problem solving while the second experiment finds a similar effect on adult analogical reasoning using a markedly different analogical completion paradigm. The results are interpreted as providing evidence for the more general framework that cognitive representations of relations are best understood as mental transformations.

Fermilab accelerator control system: Analog monitoring facilities

International Nuclear Information System (INIS)

Seino, K.; Anderson, L.; Smedinghoff, J.

1987-10-01

Thousands of analog signals are monitored in different areas of the Fermilab accelerator complex. For general purposes, analog signals are sent over coaxial or twinaxial cables with varying lengths, collected at fan-in boxes and digitized with 12 bit multiplexed ADCs. For higher resolution requirements, analog signals are digitized at sources and are serially sent to the control system. This paper surveys ADC subsystems that are used with the accelerator control systems and discusses practical problems and solutions, and it describes how analog data are presented on the console system

Signal-to-noise ratio estimation in digital computer simulation of lowpass and bandpass systems with applications to analog and digital communications, volume 3

Science.gov (United States)

Tranter, W. H.; Turner, M. D.

1977-01-01

Techniques are developed to estimate power gain, delay, signal-to-noise ratio, and mean square error in digital computer simulations of lowpass and bandpass systems. The techniques are applied to analog and digital communications. The signal-to-noise ratio estimates are shown to be maximum likelihood estimates in additive white Gaussian noise. The methods are seen to be especially useful for digital communication systems where the mapping from the signal-to-noise ratio to the error probability can be obtained. Simulation results show the techniques developed to be accurate and quite versatile in evaluating the performance of many systems through digital computer simulation.

Musik som analogi og metafor

DEFF Research Database (Denmark)

Bonde, Lars Ole

2014-01-01

Indeholder underkapitlerne: 2.5.1 Musik som analogi 2.5.2 Musik som metafor 2.5.3 Musikkens psykologiske funktioner - en taxonomi og metaforisk lytning til fire baroksatser......Indeholder underkapitlerne: 2.5.1 Musik som analogi 2.5.2 Musik som metafor 2.5.3 Musikkens psykologiske funktioner - en taxonomi og metaforisk lytning til fire baroksatser...

Analog-to-digital conversion using custom CMOS analog memory for the EOS time projection chamber

International Nuclear Information System (INIS)

Lee, K.L.; Arthur, A.A.; Jones, R.W.; Matis, H.S.; Nakamura, M.; Kleinfelder, S.A.; Ritter, H.G.; Wienman, H.H.

1990-01-01

This paper describes the multiplexing scheme of custom CMOS analog memory integrated circuits, 16 channels x 256 cells, into analog to digital converters (ADC's) to handle 15,360 signal channels of a time projection, chamber detector system. Primary requirements of this system are high density, low power and large dynamic range. The analog memory device multiplexing scheme was designed to digitize the information stored in the memory cells. The digitization time of the ADC's and the settling times for the memory unit were carefully interleaved to optimize the performance and timing during the multiplexing operation. This kept the total number of ADC's, a costly and power dissipative component, to an acceptable minimum

Errors, error detection, error correction and hippocampal-region damage: data and theories.

Science.gov (United States)

MacKay, Donald G; Johnson, Laura W

2013-11-01

This review and perspective article outlines 15 observational constraints on theories of errors, error detection, and error correction, and their relation to hippocampal-region (HR) damage. The core observations come from 10 studies with H.M., an amnesic with cerebellar and HR damage but virtually no neocortical damage. Three studies examined the detection of errors planted in visual scenes (e.g., a bird flying in a fish bowl in a school classroom) and sentences (e.g., I helped themselves to the birthday cake). In all three experiments, H.M. detected reliably fewer errors than carefully matched memory-normal controls. Other studies examined the detection and correction of self-produced errors, with controls for comprehension of the instructions, impaired visual acuity, temporal factors, motoric slowing, forgetting, excessive memory load, lack of motivation, and deficits in visual scanning or attention. In these studies, H.M. corrected reliably fewer errors than memory-normal and cerebellar controls, and his uncorrected errors in speech, object naming, and reading aloud exhibited two consistent features: omission and anomaly. For example, in sentence production tasks, H.M. omitted one or more words in uncorrected encoding errors that rendered his sentences anomalous (incoherent, incomplete, or ungrammatical) reliably more often than controls. Besides explaining these core findings, the theoretical principles discussed here explain H.M.'s retrograde amnesia for once familiar episodic and semantic information; his anterograde amnesia for novel information; his deficits in visual cognition, sentence comprehension, sentence production, sentence reading, and object naming; and effects of aging on his ability to read isolated low frequency words aloud. These theoretical principles also explain a wide range of other data on error detection and correction and generate new predictions for future test. Copyright © 2013 Elsevier Ltd. All rights reserved.

NASA HRP Immunology Discipline - Use of Terrestrial Analogs

Science.gov (United States)

Crucian, Brian

2014-01-01

Due to the cost and operational constraints, as well as technical implementation limitations, it is desirous to perform relevant space physiology investigations first in terrestrial 'space analogs'. This is particularly true for initial investigations, which may then provide appropriate focus for subsequent flight investigations, or for mechanistic investigations that simply cannot be performed during spaceflight. Appropriate analog choice is extremely important. There are a wide variety of terrestrial space analogs, each relevant to a particular physiological discipline (or disciplines) and each with a particular fidelity (or lack thereof) to spaceflight, and each with unique operational constraints. The HRP Immunology Discipline is tasked with managing the HRP Risk concerning clinical risk for Astronaut crews related to spaceflight-associated immune dysregulation. Such dysregulation has been documented to occur during spaceflight, and found to persist for the duration of a 6-month ISS mission. Studies continue to characterize the onorbit phenomenon, but it generally consists of diminished immunocyte function, dysregulated cytokine profiles, and persistent herpesvirus reactivation. Causes are thought to synergistically include microgravity, psychological or physiological stress, radiation, and/or circadian misalignment. An appropriate terrestrial analog for immune dysregulation would replicate as many of these influences as possible. Such analogs may include clinostat or bioreactor cell culture (microgravity), hindlimb suspension (stress, fluid shifts, hypokinesis), or human deployment to remote or extreme environments (isolation, stress, circadian). Also, the laboratory setting may be used as an analog, or to augment analogs, such as sleep deprivation/misalignment or human centrifugation to replicate gravitational stress. As an appropriate example of a NASA Disciplines use of Terrestrial space analogs, this talk will discuss spaceflight associated immune

The Development of Analogical Reasoning Processes.

Science.gov (United States)

Sternberg, Robert J.; Rifkin, Bathsheva

1979-01-01

Two experiments were conducted to test the generalizability to children of a theory of analogical reasoning processes, originally proposed for adults, and to examine the development of analogical reasoning processes in terms of five proposed sources of cognitive development. (MP)

Computational approaches to analogical reasoning current trends

CERN Document Server

Richard, Gilles

2014-01-01

Analogical reasoning is known as a powerful mode for drawing plausible conclusions and solving problems. It has been the topic of a huge number of works by philosophers, anthropologists, linguists, psychologists, and computer scientists. As such, it has been early studied in artificial intelligence, with a particular renewal of interest in the last decade. The present volume provides a structured view of current research trends on computational approaches to analogical reasoning. It starts with an overview of the field, with an extensive bibliography. The 14 collected contributions cover a large scope of issues. First, the use of analogical proportions and analogies is explained and discussed in various natural language processing problems, as well as in automated deduction. Then, different formal frameworks for handling analogies are presented, dealing with case-based reasoning, heuristic-driven theory projection, commonsense reasoning about incomplete rule bases, logical proportions induced by similarity an...

Effect of DMDF on the PM emission from a turbo-charged diesel engine with DDOC and DPOC

International Nuclear Information System (INIS)

Geng, Peng; Yao, Chunde; Wang, Quangang; Wei, Lijiang; Liu, Junheng; Pan, Wang; Han, Guopeng

2015-01-01

Highlights: • A new technical route on the reductions of smoke emissions and PM was introduced. • Smoke emissions and PM from turbo-charged diesel engine with DMDF were measured. • Interior relation on dry-soot, smoke opacity and PM was analyzed. • Effects of DMDF, DDOC and DPOC on smoke emissions and PM were investigated. • Particle number and mass concentrations and size contribution with DMDF were realized. - Abstract: This study is aimed to investigate the combined application of diesel methanol dual fuel (DMDF) and a simple after-treatment for reducing particulate matter (PM) emissions of a diesel engine. The effects of DMDF, a double diesel oxidation catalyst (DDOC) and a DOC closely coupled with a particulate oxidation catalyst (POC) in series (DPOC) on smoke emissions, particulate mass and number concentrations and size distributions were analyzed. Tests were conducted on a 4-cylinder turbo-charged, inter-cooling, mechanical in-line fuel injection pump diesel engine modified to DMDF combustion mode. Testing results showed that, before the DDOC and the DPOC, the dry-soot and smoke opacity efficiency decreases with the increase of substitution ratio of methanol at high engine load. There is a significant decrease of smoke opacity in DMDF mode after the DDOC, while the DPOC has a significant effect on the reduction in dry-soot emission. There is an average reduction in dry-soot by 25% in pure diesel fuel mode after the DDOC, while in DMDF mode, the average reduction is more than 60%, and the maximum reduction in dry-soot is up to 96%. There is a slightly reduction in PM emissions at low substitution ratio of methanol, while the high substitution ratio of methanol leads to more reduction in PM emissions. After the DDOC and the DPOC, particulate number and mass concentrations, especially nuclear particles, can be significantly reduced when the exhaust gas temperature is enough high

Design and Analysis of Reconfigurable Analog System

Science.gov (United States)

2011-02-01

34010010" �" �" �" �" �" �" �±" N3 N2 N± P1 P2 P3 * Current sources $RR = 1; *Ramp Rate (slope of the...2008/12/12/31e83bac-500f-4182- acca -4d360295fd9c.pdf, Analog Devices, Analog Dialogue 39-06, June 2005. [15] D. A. Johns, K. Martin "Analog Integrated

Crows spontaneously exhibit analogical reasoning.

Science.gov (United States)

Smirnova, Anna; Zorina, Zoya; Obozova, Tanya; Wasserman, Edward

2015-01-19

Analogical reasoning is vital to advanced cognition and behavioral adaptation. Many theorists deem analogical thinking to be uniquely human and to be foundational to categorization, creative problem solving, and scientific discovery. Comparative psychologists have long been interested in the species generality of analogical reasoning, but they initially found it difficult to obtain empirical support for such thinking in nonhuman animals (for pioneering efforts, see [2, 3]). Researchers have since mustered considerable evidence and argument that relational matching-to-sample (RMTS) effectively captures the essence of analogy, in which the relevant logical arguments are presented visually. In RMTS, choice of test pair BB would be correct if the sample pair were AA, whereas choice of test pair EF would be correct if the sample pair were CD. Critically, no items in the correct test pair physically match items in the sample pair, thus demanding that only relational sameness or differentness is available to support accurate choice responding. Initial evidence suggested that only humans and apes can successfully learn RMTS with pairs of sample and test items; however, monkeys have subsequently done so. Here, we report that crows too exhibit relational matching behavior. Even more importantly, crows spontaneously display relational responding without ever having been trained on RMTS; they had only been trained on identity matching-to-sample (IMTS). Such robust and uninstructed relational matching behavior represents the most convincing evidence yet of analogical reasoning in a nonprimate species, as apes alone have spontaneously exhibited RMTS behavior after only IMTS training. Copyright © 2015 Elsevier Ltd. All rights reserved.

Perceptions of Rebuttal Analogy: Politeness and Implications for Persuasion.

Science.gov (United States)

Whaley, Bryan B.

1997-01-01

States that recent theorizing about the role of analogy in persuasion suggests that "rebuttal" analogy addresses two communicative functions by serving as argument and a method of social attack. Examines message receivers' perceptions of rebuttal analogy and rebuttal analogy users. Finds that participants perceived the communicator using…

Elucidating the neurotoxic effects of MDMA and its analogs.

Science.gov (United States)

Karuppagounder, Senthilkumar S; Bhattacharya, Dwipayan; Ahuja, Manuj; Suppiramaniam, Vishnu; Deruiter, Jack; Clark, Randall; Dhanasekaran, Muralikrishnan

2014-04-17

There is a rapid increase in the use of methylenedioxymethamphetamine (MDMA) and its structural congeners/analogs globally. MDMA and MDMA-analogs have been synthesized illegally in furtive dwellings and are abused due to its addictive potential. Furthermore, MDMA and MDMA-analogs have shown to have induced several adverse effects. Hence, understanding the mechanisms mediating this neurotoxic insult of MDMA-analogs is of immense importance for the public health in the world. We synthesized and investigated the neurotoxic effects of MDMA and its analogs [4-methylenedioxyamphetamine (MDA), 2, 6-methylenedioxyamphetamine (MDMA), and N-ethyl-3, 4-methylenedioxyamphetamine (MDEA)]. The stimulatory or the dopaminergic agonist effects of MDMA and MDMA-analogs were elucidated using the established 6-hydroxydopamine lesioned animal model. Additionally, we also investigated the neurotoxic mechanisms of MDMA and MDMA-analogs on mitochondrial complex-I activity and reactive oxygen species generation. MDMA and MDMA-analogs exhibited stimulatory activity as compared to amphetamines and also induced several behavioral changes in the rodents. MDMA and MDMA-analogs enhanced the reactive oxygen generation and inhibited mitochondrial complex-I activity which can lead to neurodegeneration. Hence the mechanism of neurotoxicity, MDMA and MDMA-analogs can enhance the release of monoamines, alter the monoaminergic neurotransmission, and augment oxidative stress and mitochondrial abnormalities leading to neurotoxicity. Thus, our study will help in developing effective pharmacological and therapeutic approaches for the treatment of MDMA and MDMA-analog abuse. Copyright © 2014 Elsevier Inc. All rights reserved.

Learning Plate Tectonics Using a Pre-Analogy Step

Science.gov (United States)

Glesener, G. B.; Sandoval, W. A.

2011-12-01

Previous research has shown that children tend to demonstrate lower performance on analogical reasoning tasks at a causal relations level compared to most adults (Gentner & Toupin, 1986). This tendency is an obstacle that geoscience educators must overcome because of the high frequency of analogies used in geoscience pedagogy. In particular, analog models are used to convey complex systems of non-everyday/non-observable events found in nature, such as plate tectonics. Key factors in successful analogical reasoning that have been suggested by researchers include knowledge of the causal relations in the base analog (Brown & Kane, 1988; Gentner, 1988; Gentner & Toupin, 1986), and development of learning strategies and metaconceptual competence(Brown & Kane, 1988). External factors, such as guiding cues and hints have been useful cognitive supports that help students reason through analogical problems (Gick & Holyoak, 1980). Cognitive supports have been seen by researchers to decrease processing demands on retrieval and working memory (Richland, Zur, & Holyoak, 2007). We observed third and fourth graders learning about plate tectonics beginning with a pre-analogy step-a cognitive support activity a student can do before working with an analogy to understand the target. This activity was designed to aid students in developing their understanding of object attributes and relations within an analog model so that more focus can be placed on mapping the corresponding higher-order relations between the base and target. Students learned targeted concepts of plate tectonics, as measured by pre to post gains on items adapted from the Geosciences Concept Inventory. Analyses of classroom interaction showed that students used the object attributes and higher-order relations highlighted in the pre-analogy activity as resources to reason about plate boundaries and plate movement during earthquakes.

Natural analogs for Yucca Mountain

International Nuclear Information System (INIS)

Murphy, W.M.

1995-01-01

High-level radioactive waste in the US, spent fuels from commercial reactors and nuclear materials generated by defense activities, will remain potentially hazardous for thousands of years. Demonstrable long-term stability of certain geologic and geochemical systems motivates and sustains the concept that high-level waste can be safely isolated in geologic repositories for requisite periods of time. Each geologic repository is unique in its properties and performance with reguard to isolation of nuclear wastes. Studies of processes analogous to waste-form alteration and radioelement transport in environments analogous to Yucca Mountain are being conducted at two sites, described in this article to illustrate uses of natural analog data: the Nopal I uranium deposit in the Sierra Pena Blanca, Mexico, and the Akrotiri archaeological site on the island of Santorini, Greece

Performance Evaluation of Analog Beamforming with Hardware Impairments for mmW Massive MIMO Communication in an Urban Scenario

Directory of Open Access Journals (Sweden)

Sonia Gimenez

2016-09-01

Full Text Available The use of massive multiple-input multiple-output (MIMO techniques for communication at millimeter-Wave (mmW frequency bands has become a key enabler to meet the data rate demands of the upcoming fifth generation (5G cellular systems. In particular, analog and hybrid beamforming solutions are receiving increasing attention as less expensive and more power efficient alternatives to fully digital precoding schemes. Despite their proven good performance in simple setups, their suitability for realistic cellular systems with many interfering base stations and users is still unclear. Furthermore, the performance of massive MIMO beamforming and precoding methods are in practice also affected by practical limitations and hardware constraints. In this sense, this paper assesses the performance of digital precoding and analog beamforming in an urban cellular system with an accurate mmW channel model under both ideal and realistic assumptions. The results show that analog beamforming can reach the performance of fully digital maximum ratio transmission under line of sight conditions and with a sufficient number of parallel radio-frequency (RF chains, especially when the practical limitations of outdated channel information and per antenna power constraints are considered. This work also shows the impact of the phase shifter errors and combiner losses introduced by real phase shifter and combiner implementations over analog beamforming, where the former ones have minor impact on the performance, while the latter ones determine the optimum number of RF chains to be used in practice.

Analogy-Enhanced Instruction: Effects on Reasoning Skills in Science

Science.gov (United States)

Remigio, Krisette B.; Yangco, Rosanelia T.; Espinosa, Allen A.

2014-01-01

The study examined the reasoning skills of first year high school students after learning general science concepts through analogies. Two intact heterogeneous sections were randomly assigned to Analogy-Enhanced Instruction (AEI) group and Non Analogy-Enhanced (NAEI) group. Various analogies were incorporated in the lessons of the AEI group for…

Multisensor transducer based on a parallel fiber optic digital-to-analog converter

Directory of Open Access Journals (Sweden)

Grechishnikov Vladimir

2017-01-01

Full Text Available Considered possibility of creating a multisensory information converter (MSPI based on new fiber-optic functional element-digital-to-analog (DAC fiber optic converter. The use of DAC fiber-optic provides jamming immunity combined with low weight and cost of indicators .Because of that MSPI scheme was developed based on parallel DAC fiber-optic (Russian Federation Patent 157416. We came up with an equation for parallel DAC fiber-optic. An eleborate general mathematical model of the proposed converter. Developed a method for reducing conversion errors by placing the DAC transfer function between i and i + 1 ADC quantization levels. By using this model it allows you to obtain reliable information about the technical capabilities of a converter without the need for costly experiments.

Bounds on achievable accuracy in analog optical linear-algebra processors

Science.gov (United States)

Batsell, Stephen G.; Walkup, John F.; Krile, Thomas F.

1990-07-01

Upper arid lower bounds on the number of bits of accuracy achievable are determined by applying a seconth-ortler statistical model to the linear algebra processor. The use of bounds was found necessary due to the strong signal-dependence of the noise at the output of the optical linear algebra processor (OLAP). 1 1. ACCURACY BOUNDS One of the limiting factors in applying OLAPs to real world problems has been the poor achievable accuracy of these processors. Little previous research has been done on determining noise sources from a systems perspective which would include noise generated in the multiplication ard addition operations spatial variations across arrays and crosstalk. We have previously examined these noise sources and determined a general model for the output noise mean and variance. The model demonstrates a strony signaldependency in the noise at the output of the processor which has been confirmed by our experiments. 1 We define accuracy similar to its definition for an analog signal input to an analog-to-digital (ND) converter. The number of bits of accuracy achievable is related to the log (base 2) of the number of separable levels at the P/D converter output. The number of separable levels is fouri by dividing the dynamic range by m times the standard deviation of the signal a. 2 Here m determines the error rate in the P/D conversion. The dynamic range can be expressed as the

Epistemology of analogy: Knowledge, society and expression

Directory of Open Access Journals (Sweden)

Mauricio Beuchot

2017-06-01

Full Text Available In this article we expose the bases of analog epistemology. This theory of knowledge is between an extreme subjectivism and an extreme objectivism. Analog hermeneutics is a realistic hermeneutics. She seeks the truth, but incorporates the meaning and emotion. We have separated the reason from the experience, the praxis theory, the mind or the soul of the body. We have to get them back together, if we do not get lost in the rational (which says little of the human being, or we lose ourselves in the emotional (without logical consistency. The analogical hermeneutic realism is able, thanks to the analogy itself, to mediate in this way of union.

Explaining Chinese Learners’ Errors in the Phonological Representations of Latinate Derivatives in English: A Psycholinguistic Perspective

Directory of Open Access Journals (Sweden)

Siok H. Lee

2002-06-01

Full Text Available Abstract Investigations of ESL pronunciation have focused on segments, syllable structure and prosody. This study examines the phonological representations of English Latinate derivatives of 32 Cantonese speakers and 32 native speakers (NS from the perspectives of morphophonemics and word association. The subjects (Grade 12 performed tests on listening, pronunciation and semantic rating of word pairs. The results confirmed the hypothesis that in the absence of analogous morphological and morphophonemic features in the L1, base-word pronunciation was the dominant error type for both learners and the NS subjects. As both groups showed comparable rates of recognition of the semantic association between morphologically related words, this recognition seems to account for the dominant error type of both ESL and NS groups.

Analog elements for transuranic chemistries

International Nuclear Information System (INIS)

Weimer, W.C.

1982-01-01

The analytical technique for measuring trace concentrations of the analog rare earth elements has been refined for optimal detection. The technique has been used to determine the rare earth concentrations in a series of geological and biological materials, including samples harvested from controlled lysimeter investigations. These studies have demonstrated that any of the trivalent rare earth elements may be used as analog elements for the trivalent transuranics, americium and curium

Learning time-dependent noise to reduce logical errors: real time error rate estimation in quantum error correction

Science.gov (United States)

Huo, Ming-Xia; Li, Ying

2017-12-01

Quantum error correction is important to quantum information processing, which allows us to reliably process information encoded in quantum error correction codes. Efficient quantum error correction benefits from the knowledge of error rates. We propose a protocol for monitoring error rates in real time without interrupting the quantum error correction. Any adaptation of the quantum error correction code or its implementation circuit is not required. The protocol can be directly applied to the most advanced quantum error correction techniques, e.g. surface code. A Gaussian processes algorithm is used to estimate and predict error rates based on error correction data in the past. We find that using these estimated error rates, the probability of error correction failures can be significantly reduced by a factor increasing with the code distance.

Analogy, explanation, and proof

Science.gov (United States)

Hummel, John E.; Licato, John; Bringsjord, Selmer

2014-01-01

People are habitual explanation generators. At its most mundane, our propensity to explain allows us to infer that we should not drink milk that smells sour; at the other extreme, it allows us to establish facts (e.g., theorems in mathematical logic) whose truth was not even known prior to the existence of the explanation (proof). What do the cognitive operations underlying the inference that the milk is sour have in common with the proof that, say, the square root of two is irrational? Our ability to generate explanations bears striking similarities to our ability to make analogies. Both reflect a capacity to generate inferences and generalizations that go beyond the featural similarities between a novel problem and familiar problems in terms of which the novel problem may be understood. However, a notable difference between analogy-making and explanation-generation is that the former is a process in which a single source situation is used to reason about a single target, whereas the latter often requires the reasoner to integrate multiple sources of knowledge. This seemingly small difference poses a challenge to the task of marshaling our understanding of analogical reasoning to understanding explanation. We describe a model of explanation, derived from a model of analogy, adapted to permit systematic violations of this one-to-one mapping constraint. Simulation results demonstrate that the resulting model can generate explanations for novel explananda and that, like the explanations generated by human reasoners, these explanations vary in their coherence. PMID:25414655

Analogy, Explanation, and Proof

Directory of Open Access Journals (Sweden)

John eHummel

2014-11-01

Full Text Available People are habitual explanation generators. At its most mundane, our propensity to explain allows us to infer that we should not drink milk that smells sour; at the other extreme, it allows us to establish facts (e.g., theorems in mathematical logic whose truth was not even known prior to the existence of the explanation (proof. What do the cognitive operations underlying the (inductive inference that the milk is sour have in common with the (deductive proof that, say, the square root of two is irrational? Our ability to generate explanations bears striking similarities to our ability to make analogies. Both reflect a capacity to generate inferences and generalizations that go beyond the featural similarities between a novel problem and familiar problems in terms of which the novel problem may be understood. However, a notable difference between analogy-making and explanation-generation is that the former is a process in which a single source situation is used to reason about a single target, whereas the latter often requires the reasoner to integrate multiple sources of knowledge. This small-seeming difference poses a challenge to the task of marshaling our understanding of analogical reasoning in the service of understanding explanation. We describe a model of explanation, derived from a model of analogy, adapted to permit systematic violations of this one-to-one mapping constraint. Simulation results demonstrate that the resulting model can generate explanations for novel explananda and that, like the explanations generated by human reasoners, these explanations vary in their coherence.

Insulin analogs with improved pharmacokinetic profiles.

Science.gov (United States)

Brange; Vølund

1999-02-01

The aim of insulin replacement therapy is to normalize blood glucose in order to reduce the complications of diabetes. The pharmacokinetics of the traditional insulin preparations, however, do not match the profiles of physiological insulin secretion. The introduction of the rDNA technology 20 years ago opened new ways to create insulin analogs with altered properties. Fast-acting analogs are based on the idea that an insulin with less tendency to self-association than human insulin would be more readily absorbed into the systemic circulation. Protracted-acting analogs have been created to mimic the slow, steady rate of insulin secretion in the fasting state. The present paper provides a historical review of the efforts to change the physicochemical and pharmacological properties of insulin in order to improve insulin therapy. The available clinical studies of the new insulins are surveyed and show, together with modeling results, that new strategies for optimal basal-bolus treatment are required for utilization of the new fast-acting analogs.

Los pasiegos. La analogía salvaje y lo salvaje de la analogía

Directory of Open Access Journals (Sweden)

JAIME DE LA CALLE VALVERDE

2007-01-01

-entendiendo salvaje como un pensamiento humano prístino-: por un lado en sus relaciones con el racionalismo (¿emerge la analogía desde el racionalismo?, ¿qué relación guarda con éste?, ¿su nacimiento es resultado de una función «natural»? y por otro sobre la naturaleza social de lo salvaje a partir de las bases sociales que lo producen. Es decir, se rastrea lo que de salvaje tiene la analogía, si la analogía es o no una función ahistórica y asocial del intelecto humano. No se examina todo el complejo analógico de los pasiegos, únicamente aquél que establece relaciones homólogas entre las vacas y el entorno.

How the creative use of analogies can shape medical practice.

Science.gov (United States)

Prasad, G V Ramesh

2015-06-01

Analogical reasoning is central to medical progress, and is either creative or conservative. According to Hofmann et al., conservative analogy relates concepts from old technology to new technologies with emphasis on preservation of comprehension and conduct. Creative analogy however brings new understanding to new technology, brings similarities existing in the source domain to a target domain where they previously had no bearing, and imports something entirely different from the content of the analogy itself. I defend the claim that while conservative analogies are useful by virtue of being comfortable to use from familiarity and experience, and are more easily accepted by society, they only lead to incremental advances in medicine. However, creative analogies are more exciting and productive because they generate previously unexpected associations across widely separated domains, emphasize relations over physical similarities, and structure over superficiality. I use kidney transplantation and anti-rejection medication development as an exemplar of analogical reasoning used to improve medical practice. Anti-rejection medication has not helped highly sensitized patients because of their propensity to rejecting most organs. I outline how conservative analogical reasoning led to anti-rejection medication development, but creative analogical reasoning helped highly sensitized and blood type incompatible patients through domino transplants, by which they obtain a kidney to which they are not sensitized. Creative analogical reasoning is more likely than conservative analogical reasoning to lead to revolutionary progress. While these analogies overlap and creative analogies eventually become conservative, progress is best facilitated by combining conservative and creative analogical reasoning. © 2015 John Wiley & Sons, Ltd.

Analogs for transuranic elements

International Nuclear Information System (INIS)

Weimer, W.C.; Laul, J.C.; Kutt, J.C.

1981-01-01

A combined theoretical and experimental approach is being used to estimate the long-term environmental and biogeochemical behaviors of selected transuranic elements. The objective of this research is to estimate the effect that long-term (hundreds of years) environmental weathering has on the behavior of the transuranic elements americium and curium. This is achieved by investigating the actual behavior of naturally occurring rare earth elements, especially neodymium, that serve as transuranic analogs. Determination of the analog element behavior provides data that can be used to estimate the ultimate availability to man of transuranic materials released into the environment

23rd workshop on Advances in Analog Circuit Design

CERN Document Server

Baschirotto, Andrea; Makinwa, Kofi

2015-01-01

This book is based on the 18 tutorials presented during the 23rd workshop on Advances in Analog Circuit Design.  Expert designers present readers with information about a variety of topics at the frontier of analog circuit design, serving as a valuable reference to the state-of-the-art, for anyone involved in analog circuit research and development.    • Includes coverage of high-performance analog-to-digital and digital to analog converters, integrated circuit design in scaled technologies, and time-domain signal processing; • Provides a state-of-the-art reference in analog circuit design, written by experts from industry and academia; • Presents material in a tutorial-based format.

Bayesian analogy with relational transformations.

Science.gov (United States)

Lu, Hongjing; Chen, Dawn; Holyoak, Keith J

2012-07-01

How can humans acquire relational representations that enable analogical inference and other forms of high-level reasoning? Using comparative relations as a model domain, we explore the possibility that bottom-up learning mechanisms applied to objects coded as feature vectors can yield representations of relations sufficient to solve analogy problems. We introduce Bayesian analogy with relational transformations (BART) and apply the model to the task of learning first-order comparative relations (e.g., larger, smaller, fiercer, meeker) from a set of animal pairs. Inputs are coded by vectors of continuous-valued features, based either on human magnitude ratings, normed feature ratings (De Deyne et al., 2008), or outputs of the topics model (Griffiths, Steyvers, & Tenenbaum, 2007). Bootstrapping from empirical priors, the model is able to induce first-order relations represented as probabilistic weight distributions, even when given positive examples only. These learned representations allow classification of novel instantiations of the relations and yield a symbolic distance effect of the sort obtained with both humans and other primates. BART then transforms its learned weight distributions by importance-guided mapping, thereby placing distinct dimensions into correspondence. These transformed representations allow BART to reliably solve 4-term analogies (e.g., larger:smaller::fiercer:meeker), a type of reasoning that is arguably specific to humans. Our results provide a proof-of-concept that structured analogies can be solved with representations induced from unstructured feature vectors by mechanisms that operate in a largely bottom-up fashion. We discuss potential implications for algorithmic and neural models of relational thinking, as well as for the evolution of abstract thought. Copyright 2012 APA, all rights reserved.

Analogical reasoning for reliability analysis based on generic data

Energy Technology Data Exchange (ETDEWEB)

Kozin, Igor O

1996-10-01

The paper suggests using the systemic concept 'analogy' for the foundation of an approach to analyze system reliability on the basis of generic data, describing the method of structuring the set that defines analogical models, an approach of transition from the analogical model to a reliability model and a way of obtaining reliability intervals of analogous objects.

Analogical reasoning for reliability analysis based on generic data

International Nuclear Information System (INIS)

Kozin, Igor O.

1996-01-01

The paper suggests using the systemic concept 'analogy' for the foundation of an approach to analyze system reliability on the basis of generic data, describing the method of structuring the set that defines analogical models, an approach of transition from the analogical model to a reliability model and a way of obtaining reliability intervals of analogous objects

Medication errors: prescribing faults and prescription errors.

Science.gov (United States)

Velo, Giampaolo P; Minuz, Pietro

2009-06-01

1. Medication errors are common in general practice and in hospitals. Both errors in the act of writing (prescription errors) and prescribing faults due to erroneous medical decisions can result in harm to patients. 2. Any step in the prescribing process can generate errors. Slips, lapses, or mistakes are sources of errors, as in unintended omissions in the transcription of drugs. Faults in dose selection, omitted transcription, and poor handwriting are common. 3. Inadequate knowledge or competence and incomplete information about clinical characteristics and previous treatment of individual patients can result in prescribing faults, including the use of potentially inappropriate medications. 4. An unsafe working environment, complex or undefined procedures, and inadequate communication among health-care personnel, particularly between doctors and nurses, have been identified as important underlying factors that contribute to prescription errors and prescribing faults. 5. Active interventions aimed at reducing prescription errors and prescribing faults are strongly recommended. These should be focused on the education and training of prescribers and the use of on-line aids. The complexity of the prescribing procedure should be reduced by introducing automated systems or uniform prescribing charts, in order to avoid transcription and omission errors. Feedback control systems and immediate review of prescriptions, which can be performed with the assistance of a hospital pharmacist, are also helpful. Audits should be performed periodically.

Analog electronics for radiation detection

CERN Document Server

2016-01-01

Analog Electronics for Radiation Detection showcases the latest advances in readout electronics for particle, or radiation, detectors. Featuring chapters written by international experts in their respective fields, this authoritative text: Defines the main design parameters of front-end circuitry developed in microelectronics technologies Explains the basis for the use of complementary metal oxide semiconductor (CMOS) image sensors for the detection of charged particles and other non-consumer applications Delivers an in-depth review of analog-to-digital converters (ADCs), evaluating the pros and cons of ADCs integrated at the pixel, column, and per-chip levels Describes incremental sigma delta ADCs, time-to-digital converter (TDC) architectures, and digital pulse-processing techniques complementary to analog processing Examines the fundamental parameters and front-end types associated with silicon photomultipliers used for single visible-light photon detection Discusses pixel sensors ...

Usefulness of turbo spin-echo MR imaging in meniscal tears of the knee

International Nuclear Information System (INIS)

Jeong, Gun Young; Choi, Chang Lak; Chung, Jin Young; Han, Tae Il; Jang, Hong Im; Kim, Ji Min; Han, Hyun Young; Song, Mun Kab; Yang, Chang Kyu

1998-01-01

To evaluate the usefulness and diagnostic accuracy of turbo spin-echo(TSE) proton-density and T2-weighted images of meniscal tears of the knee. We retrospectively evaluated the sensitivity, specificity, and accuracy of TSE proton density and T2-weighted images of meniscal tears confirmed arthroscopically or surgically in 47 patients(98 menisci). The routine TSE parameters used in all patients were the dual echo sequence with sagittal proton density and T2-weighed images(4000/16, 90/5/2 [TR/effectiveTE/ETL/NEX]), and fat-suppressed coronal proton density and T2-weighted images. The chi-square test was used for statistical analysis. The sensitivity, specificity, and accuracy of TSE proton density images for the detection of meniscal tears were 93.9%, 93.8%, and 93.9%, respectively, in the medial meniscus, and 92.9%, 91.4%, and 91.8% in the lateral. On T2-weighted images the corresponding figures were 87.9%, 8%, and 89.8%, respectively, in the medial meniscus, and 64.3%, 91.4%, and 83.7% in the lateral. With regard to sensitivity and accuracy, TSE proton density images of meniscal tears were superior to TSE T2-weighted images.=20

Iterative Decoding of Concatenated Codes: A Tutorial

Directory of Open Access Journals (Sweden)

Phillip A. Regalia

2005-05-01

Full Text Available The turbo decoding algorithm of a decade ago constituted a milestone in error-correction coding for digital communications, and has inspired extensions to generalized receiver topologies, including turbo equalization, turbo synchronization, and turbo CDMA, among others. Despite an accrued understanding of iterative decoding over the years, the “turbo principle” remains elusive to master analytically, thereby inciting interest from researchers outside the communications domain. In this spirit, we develop a tutorial presentation of iterative decoding for parallel and serial concatenated codes, in terms hopefully accessible to a broader audience. We motivate iterative decoding as a computationally tractable attempt to approach maximum-likelihood decoding, and characterize fixed points in terms of a “consensus” property between constituent decoders. We review how the decoding algorithm for both parallel and serial concatenated codes coincides with an alternating projection algorithm, which allows one to identify conditions under which the algorithm indeed converges to a maximum-likelihood solution, in terms of particular likelihood functions factoring into the product of their marginals. The presentation emphasizes a common framework applicable to both parallel and serial concatenated codes.

CFD Study of Turbo-Ramjet Interactions in Hypersonic Airbreathing Propulsion System

Science.gov (United States)

Chang, Ing; Hunter, Louis G.

1996-01-01

Advanced airbreathing propulsion systems used in Mach 4-6 mission scenarios, usually involve turbo-ramjet configurations. As the engines transition from turbojet to ramjet, there is an operational envelope where both engines operate simultaneously. In the first phase of our study, an over/under nozzle configuration was analyzed. The two plumes from the turbojet and ramjet interact at the end of a common 2-D cowl, where they both reach an approximate Mach 3.0 condition and then jointly expand to Mach 3.6 at the common nozzle exit plane. For the problem analyzed, the turbojet engine operates at a higher nozzle pressure ratio than the ramjet, causes the turbojet plume overpowers the ramjet plume, deflecting it approximately 12 degrees downward and in turn the turbojet plume is deflected 6 degrees upward. In the process, shocks were formed at the deflections and a shear layer formed at the confluence of the two jets. This particular case was experimentally tested and the data were used to compare with a computational fluid dynamics (CFD) study using the PARC2D code. The CFD results were in good agreement with both static pressure distributions on the cowl separator and on nozzle walls. The thrust coefficients were also in reasonable agreement. In addition, inviscid relationships were developed around the confluence point, where the two exhaust jets meet, and these results compared favorably with the CFD results. In the second phase of our study, a 3-D CFD solution was generated to compare with the 2-D solution. The major difference between the 2-D and 3-D solutions was the interaction of the shock waves, generated by the plume interactions, on the sidewall. When a shock wave interacts with a sidewall and sidewall boundary layer, it is called a glancing shock sidewall interaction. These interactions entrain boundary layer flow down the shockline into a vortical flow pattern. The 3-D plots show the streamlines being entrained down the shockline. The pressure of the flow

Influence of engine speed and the course of the fuel injection characteristics on forming the average combustion temperature in the cylinder of turbo diesel engine

Directory of Open Access Journals (Sweden)

Piotr GUSTOF

2007-01-01

Full Text Available Average combustion temperatures inside a turbo diesel engine for the same load and the same total doze of fuel for two rotational speeds: 2004 [rpm] and 4250 [rpm] are presented in this paper. The aim of this work is also the evaluation of the influence of the temporary course of the fuel injection characteristics on forming temperature in theengine cylinder space for these temperatures. The calculations were carried out by means of two zone combustion model.

Analogical Matrices in Young Children and Students with Intellectual Disability: Reasoning by Analogy or Reasoning by Association?

Science.gov (United States)

Denaes, Caroline

2012-01-01

Background: Analogical reasoning (AR) is renowned for being a complex activity. Young children tend to reason by association, rather by analogy, and people with intellectual disability present problems of memorization. Both these populations usually show low performances in AR. The present author investigated whether familiar material and external…

Neurotoxic Alkaloids: Saxitoxin and Its Analogs

Directory of Open Access Journals (Sweden)

Troco K. Mihali

2010-07-01

Full Text Available Saxitoxin (STX and its 57 analogs are a broad group of natural neurotoxic alkaloids, commonly known as the paralytic shellfish toxins (PSTs. PSTs are the causative agents of paralytic shellfish poisoning (PSP and are mostly associated with marine dinoflagellates (eukaryotes and freshwater cyanobacteria (prokaryotes, which form extensive blooms around the world. PST producing dinoflagellates belong to the genera Alexandrium, Gymnodinium and Pyrodinium whilst production has been identified in several cyanobacterial genera including Anabaena, Cylindrospermopsis, Aphanizomenon Planktothrix and Lyngbya. STX and its analogs can be structurally classified into several classes such as non-sulfated, mono-sulfated, di-sulfated, decarbamoylated and the recently discovered hydrophobic analogs—each with varying levels of toxicity. Biotransformation of the PSTs into other PST analogs has been identified within marine invertebrates, humans and bacteria. An improved understanding of PST transformation into less toxic analogs and degradation, both chemically or enzymatically, will be important for the development of methods for the detoxification of contaminated water supplies and of shellfish destined for consumption. Some PSTs also have demonstrated pharmaceutical potential as a long-term anesthetic in the treatment of anal fissures and for chronic tension-type headache. The recent elucidation of the saxitoxin biosynthetic gene cluster in cyanobacteria and the identification of new PST analogs will present opportunities to further explore the pharmaceutical potential of these intriguing alkaloids.

A hierarchical spatiotemporal analog forecasting model for count data.

Science.gov (United States)

McDermott, Patrick L; Wikle, Christopher K; Millspaugh, Joshua

2018-01-01

Analog forecasting is a mechanism-free nonlinear method that forecasts a system forward in time by examining how past states deemed similar to the current state moved forward. Previous applications of analog forecasting has been successful at producing robust forecasts for a variety of ecological and physical processes, but it has typically been presented in an empirical or heuristic procedure, rather than as a formal statistical model. The methodology presented here extends the model-based analog method of McDermott and Wikle (Environmetrics, 27, 2016, 70) by placing analog forecasting within a fully hierarchical statistical framework that can accommodate count observations. Using a Bayesian approach, the hierarchical analog model is able to quantify rigorously the uncertainty associated with forecasts. Forecasting waterfowl settling patterns in the northwestern United States and Canada is conducted by applying the hierarchical analog model to a breeding population survey dataset. Sea surface temperature (SST) in the Pacific Ocean is used to help identify potential analogs for the waterfowl settling patterns.

Molecular interactions between (--epigallocatechin gallate analogs and pancreatic lipase.

Directory of Open Access Journals (Sweden)

Shihui Wang

Full Text Available The molecular interactions between pancreatic lipase (PL and four tea polyphenols (EGCG analogs, like (--epigallocatechin gallate (EGCG, (--gallocatechin gallate (GCG, (--epicatechin gallate (ECG, and (--epigallocatechin (EC, were studied from PL activity, conformation, kinetics and thermodynamics. It was observed that EGCG analogs inhibited PL activity, and their inhibitory rates decreased by the order of EGCG>GCG>ECG>EC. PL activity at first decreased rapidly and then slowly with the increase of EGCG analogs concentrations. α-Helix content of PL secondary structure decreased dependent on EGCG analogs concentration by the order of EGCG>GCG>ECG>EC. EGCG, ECG, and EC could quench PL fluorescence both dynamically and statically, while GCG only quenched statically. EGCG analogs would induce PL self-assembly into complexes and the hydrodynamic radii of the complexes possessed a close relationship with the inhibitory rates. Kinetics analysis showed that EGCG analogs non-competitively inhibited PL activity and did not bind to PL catalytic site. DSC measurement revealed that EGCG analogs decreased the transition midpoint temperature of PL enzyme, suggesting that these compounds reduced PL enzyme thermostability. In vitro renaturation through urea solution indicated that interactions between PL and EGCG analogs were weak and non-covalent.

Functional DNA: Teaching Infinite Series through Genetic Analogy

Science.gov (United States)

Kowalski, R. Travis

2011-01-01

This article presents an extended analogy that connects infinite sequences and series to the science of genetics, by identifying power series as "DNA for a function." This analogy allows standard topics such as convergence tests or Taylor approximations to be recast in a "forensic" light as mathematical analogs of genetic concepts such as DNA…

Bifurcated states of a rotating tokamak plasma in the presence of a static error-field

International Nuclear Information System (INIS)

Fitzpatrick, R.

1998-01-01

The bifurcated states of a rotating tokamak plasma in the presence of a static, resonant, error-field are strongly analogous to the bifurcated states of a conventional induction motor. The two plasma states are the open-quotes unreconnectedclose quotes state, in which the plasma rotates and error-field-driven magnetic reconnection is suppressed, and the open-quotes fully reconnectedclose quotes state, in which the plasma rotation at the rational surface is arrested and driven magnetic reconnection proceeds without hindrance. The response regime of a rotating tokamak plasma in the vicinity of the rational surface to a static, resonant, error-field is determined by three parameters: the normalized plasma viscosity, P, the normalized plasma rotation, Q 0 , and the normalized plasma resistivity, R. There are 11 distinguishable response regimes. The extents of these regimes are calculated in P endash Q 0 endash R space. In addition, an expression for the critical error-field amplitude required to trigger a bifurcation from the open-quotes unreconnectedclose quotes to the open-quotes fully reconnectedclose quotes state is obtained in each regime. The appropriate response regime for low-density, ohmically heated, tokamak plasmas is found to be the nonlinear constant-ψ regime for small tokamaks, and the linear constant-ψ regime for large tokamaks. The critical error-field amplitude required to trigger error-field-driven magnetic reconnection in such plasmas is a rapidly decreasing function of machine size, indicating that particular care may be needed to be taken to reduce resonant error-fields in a reactor-sized tokamak. copyright 1998 American Institute of Physics

Analog techniques in CEBAF's RF control system

International Nuclear Information System (INIS)

Hovater, C.; Fugitt, J.

1989-01-01

Recent developments in high-speed analog technology have progressed into the areas of traditional RF technology. Diode related devices are being replaced by analog IC's in the CEBAF RF control system. Complex phase modulators and attenuators have been successfully tested at 70 MHz. They have three advantages over existing technology: lower cost, less temperature sensitivity, and more linearity. RF signal conditioning components and how to implement the new analog IC's will be covered in this paper. 4 refs., 5 figs

Analog techniques in CEBAF'S RF control system

International Nuclear Information System (INIS)

Hovater, C.; Fugitt, J.

1989-01-01

Recent developments in high-speed analog technology have progressed into the areas of traditional rf technology. Diode-related devices are being replaced by analog IC's in the CEBAF rf control system. Complex phase modulators and attenuators have been successfully tested at 70 MHz. They have three advantages over existing technology: lower cost, less temperature sensitivity, and more linearity. Rf signal conditioning components and how to implement the new analog IC's will be covered in this paper. 4 refs., 5 figs

Effective Low-Power Wearable Wireless Surface EMG Sensor Design Based on Analog-Compressed Sensing

Directory of Open Access Journals (Sweden)

Mohammadreza Balouchestani

2014-12-01

Full Text Available Surface Electromyography (sEMG is a non-invasive measurement process that does not involve tools and instruments to break the skin or physically enter the body to investigate and evaluate the muscular activities produced by skeletal muscles. The main drawbacks of existing sEMG systems are: (1 they are not able to provide real-time monitoring; (2 they suffer from long processing time and low speed; (3 they are not effective for wireless healthcare systems because they consume huge power. In this work, we present an analog-based Compressed Sensing (CS architecture, which consists of three novel algorithms for design and implementation of wearable wireless sEMG bio-sensor. At the transmitter side, two new algorithms are presented in order to apply the analog-CS theory before Analog to Digital Converter (ADC. At the receiver side, a robust reconstruction algorithm based on a combination of ℓ1-ℓ1-optimization and Block Sparse Bayesian Learning (BSBL framework is presented to reconstruct the original bio-signals from the compressed bio-signals. The proposed architecture allows reducing the sampling rate to 25% of Nyquist Rate (NR. In addition, the proposed architecture reduces the power consumption to 40%, Percentage Residual Difference (PRD to 24%, Root Mean Squared Error (RMSE to 2%, and the computation time from 22 s to 9.01 s, which provide good background for establishing wearable wireless healthcare systems. The proposed architecture achieves robust performance in low Signal-to-Noise Ratio (SNR for the reconstruction process.

Benefit of Analog, Programmable and Digital Hearing Aids

Directory of Open Access Journals (Sweden)

Jamileh Fatahi

2006-12-01

Full Text Available Background and Aims: As the hearing aid technology progressively promotes toward replacing analog hearing aids with digital and programmable ones, comparison of the patient satisfaction of those kinds of hearing aids by means of a valuable tool seems so necessary. So, the aim of this study was to compare self-reported benefit of analog, digitally controlled programmable and digital hearing aids for reducing disability caused by hearing impairment in mild to severe sensorineural hearing impaired persons. Materials and Methods: This cross-sectional study was performed on 90 persons with mild to severe sensorineural hearing loss dividing into three groups: 43 subjects were fitted with digital, 15 with programmable, 32 with analog hearing aids. After pure tone audiometry, Abbreviated profile of hearing aid benefit (APHAB was completed before and one month after using hearing aids to determine the benefit of them. Results: Global APHAB mean scores for digital, programmable and analog hearing aids were 49.05, 33.19 and 39.53, respectively. Ease of Communication subscale mean scores were 53.46 for digitals, 37.66 for programmables and 39.09 for analogs. Background noise subscale mean scores for digital programmable and analog hearing aids were 46.36, 25.53 and 35.31, respectively. Global and also both subscale mean scores showed significant difference between digital hearing aids and programmable and analog ones. There was no significant difference between reverberation subscale mean scores of three groups. Conclusion: It seems digital hearing aids may be more beneficial to reduce disability caused by hearing loss than analog and programmable hearing aids are.

ANALOGICAL REASONING USING TRANSFORMATIONS OF RULES

OpenAIRE

Haraguchi, Makoto; 原口, 誠

1986-01-01

A formalism of analogical reasoning is presented. The analogical reasoning can be considered as a deduction with a function of transforming logical rules. From this viewpoint, the reasoning is defined in terms of deduction, and is therefore realized in a logic programming system. The reasoning system is described as an extension of Prolog interpreter.

Centrically reordered inversion recovery half-Fourier single-shot turbo spin-echo sequence: improvement of the image quality of oxygen-enhanced MRI

International Nuclear Information System (INIS)

Ohno, Yoshiharu; Hatabu, Hiroto; Higashino, Takanori; Kawamitsu, Hideaki; Watanabe, Hirokazu; Takenaka, Daisuke; Cauteren, Marc van; Sugimura, Kazuro

2004-01-01

Purpose: The purpose of the study presented here was to determine the improvement in image quality of oxygen-enhanced magnetic resonance (MR) subtraction imaging obtained with a centrically reordered inversion recovery half-Fourier single-shot turbo spin-echo (c-IR-HASTE) sequence compared with that obtained with a conventional sequentially reordered inversion recovery single-shot HASTE (s-IR-HASTE) sequence for pulmonary imaging. Materials and methods: Oxygen-enhanced MR imaging using a 1.5 T whole body scanner was performed on 12 healthy, non-smoking volunteers. Oxygen-enhanced MR images were obtained with the coronal two-dimensional (2D) c-IR-HASTE sequence and 2D s-IR-HASTE sequence combined with respiratory triggering. For a 256x256 matrix, 132 phase-encoding steps were acquired including four steps for phase correction. Inter-echo spacing for each sequence was 4.0 ms. The effective echo time (TE) for c-IR-HASTE was 4.0 ms, and 16 ms for s-IR-HASTE. The inversion time (TI) was 900 ms. To determine the improvement in oxygen-enhanced MR subtraction imaging by c-IR-HASTE, CNRs of subtraction image, overall image quality, and image degradation of the c-IR-HASTE and s-IR-HASTE techniques were statistically compared. Results: CNR, overall image quality, and image degradation of c-IR-HASTE images showed significant improvement compared to those s-IR-HASTE images (P<0.05). Conclusion: Centrically reordered inversion recovery half-Fourier single-shot turbo spin-echo (c-IR-HASTE) sequence enhanced the signal from the lung and improved the image quality of oxygen-enhanced MR subtraction imaging

Josephson junction analog and quasiparticle-pair current

DEFF Research Database (Denmark)

Bak, Christen Kjeldahl; Pedersen, Niels Falsig

1973-01-01

A close analogy exists between a Josephson junction and a phase-locked loop. A new type of electrical analog based on this principle is presented. It is shown that the inclusion in this analog of a low-pass filter gives rise to a current of the same form as the Josephson quasiparticle-pair current....... A simple picture of the quasiparticle-pair current, which gives the right dependences, is obtained by assuming a junction cutoff frequency to be at the energy gap. ©1973 American Institute of Physics...

CMOS Analog IC Design: Fundamentals

OpenAIRE

Bruun, Erik

2018-01-01

This book is intended for use as the main textbook for an introductory course in CMOS analog integrated circuit design. It is aimed at electronics engineering students who have followed basic courses in mathematics, physics, circuit theory, electronics and signal processing. It takes the students directly from a basic level to a level where they can start working on simple analog IC design projects or continue their studies using more advanced textbooks in the field. A distinct feature of thi...

Cyclopentanoid analogs of phosphatidylcholine: susceptibility to phospholipase A2.

Science.gov (United States)

Lister, M D; Hancock, A J

1988-10-01

Six isomers of dipalmitoylcyclopentanetriol phosphocholine (cyclopentano-lecithin) were tested as potential substrates for phospholipase A2. Since each of these analogs possesses a configuration that mimics a narrow range of conformations of a glycerophospholipid molecule, the analogs were used to assess the enzyme's conformational requirements. Studies showed that all of the analogs containing the phosphocholine at the C-1 (or C-3) position could be hydrolyzed, while only one of the three analogs that contains the polar head group at the C-2 position was susceptible. Kinetic studies, however, revealed that only the all-trans-(1,3/2-1P)-cyclopentano-lecithin gave initial rates of hydrolysis that were measurable by pH-stat. Acyl group specificity of the enzyme towards the all-trans isomer was determined with an analog was acyl groups were distinguishable. The synthesis of this mixed-acid-cyclopentano-PC is described herein. When this analog was enzymatically assayed, results unequivocally showed the enzyme to be specific for C-2 acyl hydrolysis. This specificity, and data showing that the all-trans analog is stereospecifically hydrolyzed, indicate that it is acted on in an analogous manner to dipalmitoylphosphatidylcholine. These studies indicate that although the configuration of the analog is not necessarily a prerequisite for hydrolysis, there does appear to be an optimal spatial orientation for enzymatic activity. The analogy between the susceptibilities of all-trans-(1,3/2-1P)-cyclopentano-lecithin and glycero-lecithin suggests that the conformation of the glycero-lecithin during phospholipase A2-mediated hydrolysis may be best simulated by the all-trans orientation of C-O bonds in the artificial substrate.

NaturAnalogs for the Unsaturated Zone

Energy Technology Data Exchange (ETDEWEB)

A. Simmons; A. Unger; M. Murrell

2000-03-08

The purpose of this Analysis/Model Report (AMR) is to document natural and anthropogenic (human-induced) analog sites and processes that are applicable to flow and transport processes expected to occur at the potential Yucca Mountain repository in order to build increased confidence in modeling processes of Unsaturated Zone (UZ) flow and transport. This AMR was prepared in accordance with ''AMR Development Plan for U0135, Natural Analogs for the UZ'' (CRWMS 1999a). Knowledge from analog sites and processes is used as corroborating information to test and build confidence in flow and transport models of Yucca Mountain, Nevada. This AMR supports the Unsaturated Zone (UZ) Flow and Transport Process Model Report (PMR) and the Yucca Mountain Site Description. The objectives of this AMR are to test and build confidence in the representation of UZ processes in numerical models utilized in the UZ Flow and Transport Model. This is accomplished by: (1) applying data from Boxy Canyon, Idaho in simulations of UZ flow using the same methodologies incorporated in the Yucca Mountain UZ Flow and Transport Model to assess the fracture-matrix interaction conceptual model; (2) Providing a preliminary basis for analysis of radionuclide transport at Pena Blanca, Mexico as an analog of radionuclide transport at Yucca Mountain; and (3) Synthesizing existing information from natural analog studies to provide corroborating evidence for representation of ambient and thermally coupled UZ flow and transport processes in the UZ Model.

Analogy, higher order thinking, and education.

Science.gov (United States)

Richland, Lindsey Engle; Simms, Nina

2015-01-01

Analogical reasoning, the ability to understand phenomena as systems of structured relationships that can be aligned, compared, and mapped together, plays a fundamental role in the technology rich, increasingly globalized educational climate of the 21st century. Flexible, conceptual thinking is prioritized in this view of education, and schools are emphasizing 'higher order thinking', rather than memorization of a cannon of key topics. The lack of a cognitively grounded definition for higher order thinking, however, has led to a field of research and practice with little coherence across domains or connection to the large body of cognitive science research on thinking. We review literature on analogy and disciplinary higher order thinking to propose that relational reasoning can be productively considered the cognitive underpinning of higher order thinking. We highlight the utility of this framework for developing insights into practice through a review of mathematics, science, and history educational contexts. In these disciplines, analogy is essential to developing expert-like disciplinary knowledge in which concepts are understood to be systems of relationships that can be connected and flexibly manipulated. At the same time, analogies in education require explicit support to ensure that learners notice the relevance of relational thinking, have adequate processing resources available to mentally hold and manipulate relations, and are able to recognize both the similarities and differences when drawing analogies between systems of relationships. © 2015 John Wiley & Sons, Ltd.

Analog forecasting with dynamics-adapted kernels

Science.gov (United States)

Zhao, Zhizhen; Giannakis, Dimitrios

2016-09-01

Analog forecasting is a nonparametric technique introduced by Lorenz in 1969 which predicts the evolution of states of a dynamical system (or observables defined on the states) by following the evolution of the sample in a historical record of observations which most closely resembles the current initial data. Here, we introduce a suite of forecasting methods which improve traditional analog forecasting by combining ideas from kernel methods developed in harmonic analysis and machine learning and state-space reconstruction for dynamical systems. A key ingredient of our approach is to replace single-analog forecasting with weighted ensembles of analogs constructed using local similarity kernels. The kernels used here employ a number of dynamics-dependent features designed to improve forecast skill, including Takens’ delay-coordinate maps (to recover information in the initial data lost through partial observations) and a directional dependence on the dynamical vector field generating the data. Mathematically, our approach is closely related to kernel methods for out-of-sample extension of functions, and we discuss alternative strategies based on the Nyström method and the multiscale Laplacian pyramids technique. We illustrate these techniques in applications to forecasting in a low-order deterministic model for atmospheric dynamics with chaotic metastability, and interannual-scale forecasting in the North Pacific sector of a comprehensive climate model. We find that forecasts based on kernel-weighted ensembles have significantly higher skill than the conventional approach following a single analog.

Natural Analogs for the Unsaturated Zone

International Nuclear Information System (INIS)

Simmons, A.; Unger, A.; Murrell, M.

2000-01-01

The purpose of this Analysis/Model Report (AMR) is to document natural and anthropogenic (human-induced) analog sites and processes that are applicable to flow and transport processes expected to occur at the potential Yucca Mountain repository in order to build increased confidence in modeling processes of Unsaturated Zone (UZ) flow and transport. This AMR was prepared in accordance with ''AMR Development Plan for U0135, Natural Analogs for the UZ'' (CRWMS 1999a). Knowledge from analog sites and processes is used as corroborating information to test and build confidence in flow and transport models of Yucca Mountain, Nevada. This AMR supports the Unsaturated Zone (UZ) Flow and Transport Process Model Report (PMR) and the Yucca Mountain Site Description. The objectives of this AMR are to test and build confidence in the representation of UZ processes in numerical models utilized in the UZ Flow and Transport Model. This is accomplished by: (1) applying data from Boxy Canyon, Idaho in simulations of UZ flow using the same methodologies incorporated in the Yucca Mountain UZ Flow and Transport Model to assess the fracture-matrix interaction conceptual model; (2) Providing a preliminary basis for analysis of radionuclide transport at Pena Blanca, Mexico as an analog of radionuclide transport at Yucca Mountain; and (3) Synthesizing existing information from natural analog studies to provide corroborating evidence for representation of ambient and thermally coupled UZ flow and transport processes in the UZ Model

Challenge and Error: Critical Events and Attention-Related Errors

Science.gov (United States)

Cheyne, James Allan; Carriere, Jonathan S. A.; Solman, Grayden J. F.; Smilek, Daniel

2011-01-01

Attention lapses resulting from reactivity to task challenges and their consequences constitute a pervasive factor affecting everyday performance errors and accidents. A bidirectional model of attention lapses (error [image omitted] attention-lapse: Cheyne, Solman, Carriere, & Smilek, 2009) argues that errors beget errors by generating attention…

Circuit with a successive approximation analog to digital converter

NARCIS (Netherlands)

Louwsma, S.M.; Vertregt, Maarten

2011-01-01

During successive approximation analog to digital conversion a series of successive digital reference values is selected that converges towards a digital representation of an analog input signal. An analog reference signal is generated dependent on the successive digital reference values and

Circuit with a successive approximation analog to digital converter

NARCIS (Netherlands)

Louwsma, S.M.; Vertregt, Maarten

2010-01-01

During successive approximation analog to digital conversion a series of successive digital reference values is selected that converges towards a digital representation of an analog input signal. An analog reference signal is generated dependent on the successive digital reference values and

16-channel analog store and multiplexer unit

Energy Technology Data Exchange (ETDEWEB)

Brossard, M; Kulka, Z [Clermont-Ferrand-2 Univ., 63 - Aubiere (France). Lab. de Physique Corpusculaire

1979-03-15

A 16-channel analog store and multiplexer unit is described. The unit enables storing and selection of analog information which is then digitally encoded by single ADC. This solution becomes economically attractive particularly in multidetector pulse height analysis systems.

Error forecasting schemes of error correction at receiver

International Nuclear Information System (INIS)

Bhunia, C.T.

2007-08-01

To combat error in computer communication networks, ARQ (Automatic Repeat Request) techniques are used. Recently Chakraborty has proposed a simple technique called the packet combining scheme in which error is corrected at the receiver from the erroneous copies. Packet Combining (PC) scheme fails: (i) when bit error locations in erroneous copies are the same and (ii) when multiple bit errors occur. Both these have been addressed recently by two schemes known as Packet Reversed Packet Combining (PRPC) Scheme, and Modified Packet Combining (MPC) Scheme respectively. In the letter, two error forecasting correction schemes are reported, which in combination with PRPC offer higher throughput. (author)

Analogical Reasoning in the Engineering Design Process and Technology Education Applications

OpenAIRE

2008-01-01

This synthesis paper discusses the research exploring analogical reasoning, the role of analogies in the engineering design process, and educational applications for analogical reasoning. Researchers have discovered that analogical reasoning is often a fundamental cognitive tool in design problem solving. Regarding the possible role of analogical reasoning in the context of technology education; analogies may be a useful tool to develop student’s design skills, teach abstract or complex conce...

Operator errors

International Nuclear Information System (INIS)

Knuefer; Lindauer

1980-01-01

Besides that at spectacular events a combination of component failure and human error is often found. Especially the Rasmussen-Report and the German Risk Assessment Study show for pressurised water reactors that human error must not be underestimated. Although operator errors as a form of human error can never be eliminated entirely, they can be minimized and their effects kept within acceptable limits if a thorough training of personnel is combined with an adequate design of the plant against accidents. Contrary to the investigation of engineering errors, the investigation of human errors has so far been carried out with relatively small budgets. Intensified investigations in this field appear to be a worthwhile effort. (orig.)

Design of a 12-bit 80MS/s pipeline analog-to-digital converter for PLC-VDSL applications

Science.gov (United States)

Ruiz-Amaya, Jesus; Delgado-Restituto, Manuel; Fernandez-Bootello, Juan F.; de la Rosa, Jose M.

2005-06-01

This paper describes the design of a 12-bit 80MS/s pipeline Analog-to-Digital converter implemented in 0.13mm CMOS logic technology. The design has been computer-aided by a developed toolbox for the simulation, synthesis and verification of Nyquist-Rate Analog-to-Digital and Digital-to-Analog Converters in MATLAB. The embedded simulator uses SIMULINK C-coded S-functions to model all required subcircuits including their main error mechanisms. This approach allows to drastically speed up the simulation CPU-time and makes the proposed tool an advantageous alternative for fast exploration of requirements and as a design validation tool. The converter is based on a 10-stage pipeline preceded by a sample/hold with bootstrapping technique. Each stage gives 1.5 effective bits, except for the first one which provides 2.5 effective bits to improve linearity. The Analog-to-Digital architecture uses redundant bits for digital correction, it is planned to be implemented without using calibration and employs a subranging pipeline look-ahead technique to increase speed. Substrate biased MOSFETs in the depletion region are used as capacitors, linearized by a series compensation. Simulation results show that the Multi-Tone Power Ratio is higher than 56dB for several DMT test signals and the estimated Signal-to-Noise Ratio yield is supposed to be better than 62 dB from DC to Nyquist frequency. The converter dissipates less than 150mW from a 3.3V supply and occupies less than 4 mm2 die area. The results have been checked with all process corners from -40° to 85° and power supply from 3V to 3.6V.

Eye Movements Reveal Optimal Strategies for Analogical Reasoning.

Science.gov (United States)

Vendetti, Michael S; Starr, Ariel; Johnson, Elizabeth L; Modavi, Kiana; Bunge, Silvia A

2017-01-01

Analogical reasoning refers to the process of drawing inferences on the basis of the relational similarity between two domains. Although this complex cognitive ability has been the focus of inquiry for many years, most models rely on measures that cannot capture individuals' thought processes moment by moment. In the present study, we used participants' eye movements to investigate reasoning strategies in real time while solving visual propositional analogy problems (A:B::C:D). We included both a semantic and a perceptual lure on every trial to determine how these types of distracting information influence reasoning strategies. Participants spent more time fixating the analogy terms and the target relative to the other response choices, and made more saccades between the A and B items than between any other items. Participants' eyes were initially drawn to perceptual lures when looking at response choices, but they nonetheless performed the task accurately. We used participants' gaze sequences to classify each trial as representing one of three classic analogy problem solving strategies and related strategy usage to analogical reasoning performance. A project-first strategy, in which participants first extrapolate the relation between the AB pair and then generalize that relation for the C item, was both the most commonly used strategy as well as the optimal strategy for solving visual analogy problems. These findings provide new insight into the role of strategic processing in analogical problem solving.

Eye Movements Reveal Optimal Strategies for Analogical Reasoning

Directory of Open Access Journals (Sweden)

Michael S. Vendetti

2017-06-01

Full Text Available Analogical reasoning refers to the process of drawing inferences on the basis of the relational similarity between two domains. Although this complex cognitive ability has been the focus of inquiry for many years, most models rely on measures that cannot capture individuals' thought processes moment by moment. In the present study, we used participants' eye movements to investigate reasoning strategies in real time while solving visual propositional analogy problems (A:B::C:D. We included both a semantic and a perceptual lure on every trial to determine how these types of distracting information influence reasoning strategies. Participants spent more time fixating the analogy terms and the target relative to the other response choices, and made more saccades between the A and B items than between any other items. Participants' eyes were initially drawn to perceptual lures when looking at response choices, but they nonetheless performed the task accurately. We used participants' gaze sequences to classify each trial as representing one of three classic analogy problem solving strategies and related strategy usage to analogical reasoning performance. A project-first strategy, in which participants first extrapolate the relation between the AB pair and then generalize that relation for the C item, was both the most commonly used strategy as well as the optimal strategy for solving visual analogy problems. These findings provide new insight into the role of strategic processing in analogical problem solving.

An Analog Computer for Electronic Engineering Education

Science.gov (United States)

Fitch, A. L.; Iu, H. H. C.; Lu, D. D. C.

2011-01-01

This paper describes a compact analog computer and proposes its use in electronic engineering teaching laboratories to develop student understanding of applications in analog electronics, electronic components, engineering mathematics, control engineering, safe laboratory and workshop practices, circuit construction, testing, and maintenance. The…

The interplay of conflict and analogy in multidisciplinary teams.

Science.gov (United States)

Paletz, Susannah B F; Schunn, Christian D; Kim, Kevin H

2013-01-01

Creative teamwork in multidisciplinary teams is a topic of interest to cognitive psychologists on the one hand, and to both social and organizational psychologists on the other. However, the interconnections between cognitive and social layers have been rarely explored. Drawing on mental models and dissonance theories, the current study takes a central variable studied by cognitive psychologists-analogy-and examines its relationship to a central variable examined by social psychologists-conflict. In an observational, field study, over 11h of audio-video data from conversations of the Mars Exploration Rover scientists were coded for different types of analogy and micro-conflicts that reveal the character of underlying psychological mechanisms. Two different types of time-lagged logistic models applied to these data revealed asymmetric patterns of associations between analogy and conflict. Within-domain analogies, but not within-discipline or outside-discipline analogies, preceded science and work process conflicts, suggesting that in multidisciplinary teams, representational gaps in very close domains will be more likely to spark conflict. But analogies also occurred in reaction to conflict: Process and negative conflicts, but not task conflicts, preceded within-discipline analogies, but not to within-domain or outside-discipline analogies. This study demonstrates ways in which cognition can be bidirectionally tied to social processes and discourse. Copyright © 2012 Elsevier B.V. All rights reserved.

How Do Simulated Error Experiences Impact Attitudes Related to Error Prevention?

Science.gov (United States)

Breitkreuz, Karen R; Dougal, Renae L; Wright, Melanie C

2016-10-01

The objective of this project was to determine whether simulated exposure to error situations changes attitudes in a way that may have a positive impact on error prevention behaviors. Using a stratified quasi-randomized experiment design, we compared risk perception attitudes of a control group of nursing students who received standard error education (reviewed medication error content and watched movies about error experiences) to an experimental group of students who reviewed medication error content and participated in simulated error experiences. Dependent measures included perceived memorability of the educational experience, perceived frequency of errors, and perceived caution with respect to preventing errors. Experienced nursing students perceived the simulated error experiences to be more memorable than movies. Less experienced students perceived both simulated error experiences and movies to be highly memorable. After the intervention, compared with movie participants, simulation participants believed errors occurred more frequently. Both types of education increased the participants' intentions to be more cautious and reported caution remained higher than baseline for medication errors 6 months after the intervention. This study provides limited evidence of an advantage of simulation over watching movies describing actual errors with respect to manipulating attitudes related to error prevention. Both interventions resulted in long-term impacts on perceived caution in medication administration. Simulated error experiences made participants more aware of how easily errors can occur, and the movie education made participants more aware of the devastating consequences of errors.

Fluorinated analogs of malachite green: synthesis and toxicity.

Science.gov (United States)

Kraus, George A; Jeon, Insik; Nilsen-Hamilton, Marit; Awad, Ahmed M; Banerjee, Jayeeta; Parvin, Bahram

2008-04-27

A series of fluorinated analogs of malachite green (MG) have been synthesized and their toxicity to Saccharomyces cerevisiae and a human ovarian epithelial cell line examined. The toxicity profiles were found to be different for these two species. Two analogs, one with 2,4-difluoro substitution and the other with 2-fluoro substitution seem to be the most promising analogs because they showed the lowest toxicity to the human cells.

Analogies between classical statistical mechanics and quantum mechanics

International Nuclear Information System (INIS)

Uehara, M.

1986-01-01

Some analogies between nonequilibrium classical statistical mechanics and quantum mechanics, at the level of the Liouville equation and at the kinetic level, are commented on. A theorem, related to the Vlasov equation applied to a plasma, is proved. The theorem presents an analogy with Ehrenfest's theorem of quantum mechanics. An analogy between the plasma kinetic theory and Bohm's quantum theory with 'hidden variables' is also shown. (Author) [pt

Tracking cognitive phases in analogical reasoning with event-related potentials.

Science.gov (United States)

Maguire, Mandy J; McClelland, M Michelle; Donovan, Colin M; Tillman, Gail D; Krawczyk, Daniel C

2012-03-01

Analogical reasoning consists of multiple phases. Four-term analogies (A:B::C:D) have an encoding period in which the A:B pair is evaluated prior to a mapping phase. The electrophysiological timing associated with analogical reasoning has remained unclear. We used event-related potentials to identify neural timing related to analogical reasoning relative to perceptual and semantic control conditions. Spatiotemporal principal-components analyses revealed differences primarily in left frontal electrodes during encoding and mapping phases of analogies relative to the other conditions. The timing of the activity differed depending upon the phase of the problem. During the encoding of A:B terms, analogies elicited a positive deflection compared to the control conditions between 400 and 1,200 ms, but for the mapping phase analogical processing elicited a negative deflection that occurred earlier and for a shorter time period, between 350 and 625 ms. These results provide neural and behavioral evidence that 4-term analogy problems involve a highly active evaluation phase of the A:B pair. 2012 APA, all rights reserved

High-frequency analog integrated circuit design

CERN Document Server

1995-01-01

To learn more about designing analog integrated circuits (ICs) at microwave frequencies using GaAs materials, turn to this text and reference. It addresses GaAs MESFET-based IC processing. Describes the newfound ability to apply silicon analog design techniques to reliable GaAs materials and devices which, until now, was only available through technical papers scattered throughout hundred of articles in dozens of professional journals.

HAPS, a Handy Analog Programming System

DEFF Research Database (Denmark)

Højberg, Kristian Søe

1975-01-01

HAPS (Hybrid Analog Programming System) is an analog compiler that can be run on a minicomputer in an interactive mode. Essentially HAPS is written in FORTRAN. The equations to be programmed for an ana log computer are read in by using a FORTRAN-like notation. The input must contain maximum...... and emphasizes the limitations HAPS puts on equation structure, types of computing circuit, scaling, and static testing....

The use of analogy in pro-life argumentation

Directory of Open Access Journals (Sweden)

Simona Mazilu

2012-11-01

Full Text Available The paper is concerned with how analogy is strategically used in pro-life argumentation on abortion. Pragma-dialectics (van Eemeren and Grootendorst 1992 offers a set of critical questions by means of which I will evaluate the use of the argumentation based on a relation of analogy in terms of dialectical soundness. Examining various pro-life texts, I have noticed that the analogies employed remain unexplained. Therefore, despite the apparent similarities between abortion and the German holocaust or slavery, for instance, there are essential differences which are not mentioned. I claim that these analogies mainly have a rhetorical function, to operate what has been called by Micheli (2007: 960 “a transfer of emotional consensus”.

Patterns of Analogical Reasoning among Beginning Readers

Science.gov (United States)

Farrington-Flint, Lee; Wood, Clare; Canobi, Katherine H.; Faulkner, Dorothy

2004-01-01

Despite compelling evidence that analogy skills are available to beginning readers, few studies have actually explored the possibility of identifying individual differences in young children's analogy skills in early reading. The present study examined individual differences in children's use of orthographic and phonological relations between…

Single-event transients (SET) in analog circuits

International Nuclear Information System (INIS)

Chen Panxun; Zhou Kaiming

2006-01-01

A new phenomenon of single- event upset is introduced. The transient signal is produced in the output of analog circuits after a heavy ion strikes. The transient upset can influence the circuit connected with the output of analog circuits. For example, the output of operational amplifier can be connected with the input of a digital counter, and the pulse of sufficiently high transient output induced by an ion can increase counts of the counter. On the other hand, the transient voltage signal at the output of analog circuits can change the stage of other circuits. (authors)

Resistencia de Plasmodium falciparum a tres fármacos antimaláricos en Turbo (Antioquia, Colombia, 1998

Directory of Open Access Journals (Sweden)

Blair Silvia

2001-01-01

Full Text Available En 1998, se determinó in vivo e in vitro la frecuencia y el grado de resistencia de Plasmodium falciparum a los tres fármacos antimaláricos (cloroquina, amodiaquina y sulfadoxina/ pirimetamina más utilizados en el municipio de Turbo (zona de Urabá, Antioquia, Colombia en una muestra representativa de la población con malaria. Se realizaron análisis clínicos y parasitológicos durante 14 días según la prueba estándar recomendada por la Organización Mundial de la Salud. In vivo, P. falciparum mostró resistencia a la cloroquina, amodiaquina y sulfadoxina/pirimetamina con una frecuencia de 97, 7 y 13%, respectivamente; in vitro, las cifras correspondientes fueron de 21, 23 y 9%, respectivamente. La concordancia entre los resultados in vivo e in vitro fue de 23% para la cloroquina.

Fault Modeling and Testing for Analog Circuits in Complex Space Based on Supply Current and Output Voltage

Directory of Open Access Journals (Sweden)

Hongzhi Hu

2015-01-01

Full Text Available This paper deals with the modeling of fault for analog circuits. A two-dimensional (2D fault model is first proposed based on collaborative analysis of supply current and output voltage. This model is a family of circle loci on the complex plane, and it simplifies greatly the algorithms for test point selection and potential fault simulations, which are primary difficulties in fault diagnosis of analog circuits. Furthermore, in order to reduce the difficulty of fault location, an improved fault model in three-dimensional (3D complex space is proposed, which achieves a far better fault detection ratio (FDR against measurement error and parametric tolerance. To address the problem of fault masking in both 2D and 3D fault models, this paper proposes an effective design for testability (DFT method. By adding redundant bypassing-components in the circuit under test (CUT, this method achieves excellent fault isolation ratio (FIR in ambiguity group isolation. The efficacy of the proposed model and testing method is validated through experimental results provided in this paper.

An analog silicon retina with multichip configuration.

Science.gov (United States)

Kameda, Seiji; Yagi, Tetsuya

2006-01-01

The neuromorphic silicon retina is a novel analog very large scale integrated circuit that emulates the structure and the function of the retinal neuronal circuit. We fabricated a neuromorphic silicon retina, in which sample/hold circuits were embedded to generate fluctuation-suppressed outputs in the previous study [1]. The applications of this silicon retina, however, are limited because of a low spatial resolution and computational variability. In this paper, we have fabricated a multichip silicon retina in which the functional network circuits are divided into two chips: the photoreceptor network chip (P chip) and the horizontal cell network chip (H chip). The output images of the P chip are transferred to the H chip with analog voltages through the line-parallel transfer bus. The sample/hold circuits embedded in the P and H chips compensate for the pattern noise generated on the circuits, including the analog communication pathway. Using the multichip silicon retina together with an off-chip differential amplifier, spatial filtering of the image with an odd- and an even-symmetric orientation selective receptive fields was carried out in real time. The analog data transfer method in the present multichip silicon retina is useful to design analog neuromorphic multichip systems that mimic the hierarchical structure of neuronal networks in the visual system.

Reynolds analogy for the Rayleigh problem at various flow modes.

Science.gov (United States)

Abramov, A A; Butkovskii, A V

2016-07-01

The Reynolds analogy and the extended Reynolds analogy for the Rayleigh problem are considered. For a viscous incompressible fluid we derive the Reynolds analogy as a function of the Prandtl number and the Eckert number. We show that for any positive Eckert number, the Reynolds analogy as a function of the Prandtl number has a maximum. For a monatomic gas in the transitional flow regime, using the direct simulation Monte Carlo method, we investigate the extended Reynolds analogy, i.e., the relation between the shear stress and the energy flux transferred to the boundary surface, at different velocities and temperatures. We find that the extended Reynolds analogy for a rarefied monatomic gas flow with the temperature of the undisturbed gas equal to the surface temperature depends weakly on time and is close to 0.5. We show that at any fixed dimensionless time the extended Reynolds analogy depends on the plate velocity and temperature and undisturbed gas temperature mainly via the Eckert number. For Eckert numbers of the order of unity or less we generalize an extended Reynolds analogy. The generalized Reynolds analogy depends mainly only on dimensionless time for all considered Eckert numbers of the order of unity or less.

Two analogy strategies: the cases of mind metaphors and introspection

Science.gov (United States)

Fischer, Eugen

2018-04-01

Analogical reasoning is often employed in problem-solving and metaphor interpretation. This paper submits that, as a default, analogical reasoning addressing these different tasks employs different mapping strategies. In problem-solving, it employs analogy-maximising strategies (like structure mapping, Gentner, D., & Markman, A. B. (1997). Structure mapping in analogy and similarity. American Psychologist, 52, 45-56); in metaphor interpretation, analogy-minimising strategies (like ATT-Meta, Barnden, J. A. (2015). Open-ended elaborations in creative metaphor. In T. R. Besold, M. Schorlemmer, & A. Smaill (Eds.), Computational creativity research: Towards creative machines (pp. 217-242). Berlin: Springer). The two strategies interact in analogical reasoning with conceptual metaphors. This interaction leads to predictable fallacies. The paper supports these hypotheses through case-studies on "mind" metaphors from ordinary discourse, and abstract problem-solving in the philosophy of mind, respectively. It shows that (1) default metaphorical interpretations for vision- and space-cognition metaphors can be derived with a variant of the analogy-minimising ATT-Meta approach, (2) philosophically influential introspective conceptions of the mind can be derived with conceptual metaphors only through an analogy-maximising strategy, and (3) the interaction of these strategies leads to hitherto unrecognised fallacies in analogical reasoning with metaphors. This yields a debunking explanation of introspective conceptions.

25th workshop on Advances in Analog Circuit Design

CERN Document Server

Harpe, Pieter; Makinwa, Kofi

2017-01-01

This book is based on the 18 tutorials presented during the 25th workshop on Advances in Analog Circuit Design. Expert designers present readers with information about a variety of topics at the frontier of analog circuit design, including low-power and energy-efficient analog electronics, with specific contributions focusing on the design of continuous-time sigma-delta modulators, automotive electronics, and power management. This book serves as a valuable reference to the state-of-the-art, for anyone involved in analog circuit research and development.

Non-linear quantization error reduction for the temperature measurement subsystem on-board LISA Pathfinder

Science.gov (United States)

Sanjuan, J.; Nofrarias, M.

2018-04-01

Laser Interferometer Space Antenna (LISA) Pathfinder is a mission to test the technology enabling gravitational wave detection in space and to demonstrate that sub-femto-g free fall levels are possible. To do so, the distance between two free falling test masses is measured to unprecedented sensitivity by means of laser interferometry. Temperature fluctuations are one of the noise sources limiting the free fall accuracy and the interferometer performance and need to be known at the ˜10 μK Hz-1/2 level in the sub-millihertz frequency range in order to validate the noise models for the future space-based gravitational wave detector LISA. The temperature measurement subsystem on LISA Pathfinder is in charge of monitoring the thermal environment at key locations with noise levels of 7.5 μK Hz-1/2 at the sub-millihertz. However, its performance worsens by one to two orders of magnitude when slowly changing temperatures are measured due to errors introduced by analog-to-digital converter non-linearities. In this paper, we present a method to reduce this effect by data post-processing. The method is applied to experimental data available from on-ground validation tests to demonstrate its performance and the potential benefit for in-flight data. The analog-to-digital converter effects are reduced by a factor between three and six in the frequencies where the errors play an important role. An average 2.7 fold noise reduction is demonstrated in the 0.3 mHz-2 mHz band.

Statistical errors in Monte Carlo estimates of systematic errors

Energy Technology Data Exchange (ETDEWEB)

Roe, Byron P. [Department of Physics, University of Michigan, Ann Arbor, MI 48109 (United States)]. E-mail: byronroe@umich.edu

2007-01-01

For estimating the effects of a number of systematic errors on a data sample, one can generate Monte Carlo (MC) runs with systematic parameters varied and examine the change in the desired observed result. Two methods are often used. In the unisim method, the systematic parameters are varied one at a time by one standard deviation, each parameter corresponding to a MC run. In the multisim method (see ), each MC run has all of the parameters varied; the amount of variation is chosen from the expected distribution of each systematic parameter, usually assumed to be a normal distribution. The variance of the overall systematic error determination is derived for each of the two methods and comparisons are made between them. If one focuses not on the error in the prediction of an individual systematic error, but on the overall error due to all systematic errors in the error matrix element in data bin m, the number of events needed is strongly reduced because of the averaging effect over all of the errors. For simple models presented here the multisim model was far better if the statistical error in the MC samples was larger than an individual systematic error, while for the reverse case, the unisim model was better. Exact formulas and formulas for the simple toy models are presented so that realistic calculations can be made. The calculations in the present note are valid if the errors are in a linear region. If that region extends sufficiently far, one can have the unisims or multisims correspond to k standard deviations instead of one. This reduces the number of events required by a factor of k{sup 2}.

Statistical errors in Monte Carlo estimates of systematic errors

International Nuclear Information System (INIS)

Roe, Byron P.

2007-01-01

For estimating the effects of a number of systematic errors on a data sample, one can generate Monte Carlo (MC) runs with systematic parameters varied and examine the change in the desired observed result. Two methods are often used. In the unisim method, the systematic parameters are varied one at a time by one standard deviation, each parameter corresponding to a MC run. In the multisim method (see ), each MC run has all of the parameters varied; the amount of variation is chosen from the expected distribution of each systematic parameter, usually assumed to be a normal distribution. The variance of the overall systematic error determination is derived for each of the two methods and comparisons are made between them. If one focuses not on the error in the prediction of an individual systematic error, but on the overall error due to all systematic errors in the error matrix element in data bin m, the number of events needed is strongly reduced because of the averaging effect over all of the errors. For simple models presented here the multisim model was far better if the statistical error in the MC samples was larger than an individual systematic error, while for the reverse case, the unisim model was better. Exact formulas and formulas for the simple toy models are presented so that realistic calculations can be made. The calculations in the present note are valid if the errors are in a linear region. If that region extends sufficiently far, one can have the unisims or multisims correspond to k standard deviations instead of one. This reduces the number of events required by a factor of k 2

Is the Link from Working Memory to Analogy Causal? No Analogy Improvements following Working Memory Training Gains

OpenAIRE

Richey, J. Elizabeth; Phillips, Jeffrey S.; Schunn, Christian D.; Schneider, Walter

2014-01-01

Analogical reasoning has been hypothesized to critically depend upon working memory through correlational data [1], but less work has tested this relationship through experimental manipulation [2]. An opportunity for examining the connection between working memory and analogical reasoning has emerged from the growing, although somewhat controversial, body of literature suggests complex working memory training can sometimes lead to working memory improvements that transfer to novel working mem...

Selective termination, fetal reduction and analogical reasoning.

Science.gov (United States)

Pennings, G

2013-06-01

Analogical reasoning is a basic method in bioethics. Its main purpose is to transfer the rule from an existing or known situation to a new and problematic situation. This commentary applies the lifeboat analogy to the context of selective termination and fetal reduction. It turns out that the analogy is only partially helpful as the main principle in the case of selective termination is the procreative beneficence principle. However, the wide person-affecting form of this principle doubly justifies selective termination: i.e. one prevents the harm caused by the birth of an affected child and one increases the life chances of the remaining fetuses. I conclude, however, that all analogies are basically flawed since they assume that fetuses as such have interests. I argue that fetuses only have interests to the extent that they are potential future persons. Copyright © 2013 Reproductive Healthcare Ltd. Published by Elsevier Ltd. All rights reserved.

The design analogy : a model for moral problem solving

NARCIS (Netherlands)

Dorst, C.H.; Royakkers, L.M.M.

2006-01-01

In this paper we explore an analogy between design and ethics, first drawn by Whitbeck. We investigate her claim that such an analogy can help to understand moral problems and aid us in dealing with them by suggesting strategies for addressing moral problems. We explore the nature of analogies, and

Real-Time Observation of Platinum Redispersion on Ceria-Based Oxide by In-situ Turbo-XAS in Fluorescence Mode

International Nuclear Information System (INIS)

Nagai, Yasutaka; Dohmae, Kazuhiko; Tanabe, Toshitaka; Shinjoh, Hirofumi; Takagi, Nobuyuki; Ikeda, Yasuo; Guilera, Gemma; Pascarelli, Sakura; Newton, Mark; Matsumoto, Shin'ichi

2007-01-01

A real-time observation of the redispersion behavior of sintered Pt on ceria-based oxide was made possible by in-situ time-resolved Turbo-XAS in fluorescence mode. 2 wt% Pt/Ce-Zr-Y mixed oxide samples were prepared, and then treated under an aging condition. The average Pt particle size measured by CO absorption method after aging was 7 nm. Redispersion treatments of the previously aged catalyst were carried out at 600 deg. C within an in-situ XAS cell in a cyclical flow of reducing/oxidizing gases. Pt L3-edge XANES spectra were collected every 1.1 second under in-situ conditions. From a change in the XANES spectra, we observed that the Pt particle size of the aged catalyst decreased from 7 to 5 nm after 60 seconds and then to 3 nm after 1000 seconds

Usefulness of fluid attenuated inversion recovery(FLAIR) image in mesial temporal sclerosis : comparison with turbo spin-echo T2-weighted image

Energy Technology Data Exchange (ETDEWEB)

Son, Seok Hyun; Chang, Seung Kuk; Eun, Choong Ki [Pusan Paik Hospital, Inje Univ. College of Medicine, Kimhae (Korea, Republic of)

1999-12-01

To determine the usefulness of fluid attenuated inversion recovery(FLAIR) imaging for the in detection of high signal intensity of hippocampus or amygdala in mesial temporal sclerosis (MTS), compared with that of turbo spin-echo T2-weighted imaging. Two neuroradiologists independently analyzed randomly mixed MR images of 20 lesions of 17 patients in whom MTS had been diagnosed, and ten normal controls. All subjects underwent both who performed both FLAIR and turbo spin-echo T2-weighted imaging, in a blind fashion. In order to determine hippocampal morphology, oblique coronal images perpendicular to the long axis of the hippocampus were obtained. The detection rate of high signal intensity in hippocampus or amygdala, the radiologists' preferred imaging sequence, and intersubject consistency of detection were evaluated. Signal intensity in hippocampus or amygdala was considered high if substantially higher than signal intensity in the cortex of adjacent temporo-parietal lobe. In all normal controls, FLAIR and spin-echo T2-weighted images showed normal signal intensity in hippocampus or amygdala. In MTS, the mean detection rate of high signal intensity in hippocampus or amygdala, as seen on FLAIR images was 93%, compared with 43% on spin-echo T2-weighted images. In all cases in which signal intensity on FLAIR images was normal, signal intensity on spin-echo T2-weighted images was also normal. The radiologists preferred the contrast properties of FLAIR to those of spin-echo T2-weighted images. In the diagnosis of MTS using MRI, FLAIR images are more useful for the detection of high signal intensity of hippocampus or amygdala than are spin-echo T2-weighted images. In the diagnosis of MTS, FLAIR imaging is therefore a suitable alternative to spin-echo T2-weighted imaging.

Usefulness of fluid attenuated inversion recovery(FLAIR) image in mesial temporal sclerosis : comparison with turbo spin-echo T2-weighted image

International Nuclear Information System (INIS)

Son, Seok Hyun; Chang, Seung Kuk; Eun, Choong Ki

1999-01-01

To determine the usefulness of fluid attenuated inversion recovery(FLAIR) imaging for the in detection of high signal intensity of hippocampus or amygdala in mesial temporal sclerosis (MTS), compared with that of turbo spin-echo T2-weighted imaging. Two neuroradiologists independently analyzed randomly mixed MR images of 20 lesions of 17 patients in whom MTS had been diagnosed, and ten normal controls. All subjects underwent both who performed both FLAIR and turbo spin-echo T2-weighted imaging, in a blind fashion. In order to determine hippocampal morphology, oblique coronal images perpendicular to the long axis of the hippocampus were obtained. The detection rate of high signal intensity in hippocampus or amygdala, the radiologists' preferred imaging sequence, and intersubject consistency of detection were evaluated. Signal intensity in hippocampus or amygdala was considered high if substantially higher than signal intensity in the cortex of adjacent temporo-parietal lobe. In all normal controls, FLAIR and spin-echo T2-weighted images showed normal signal intensity in hippocampus or amygdala. In MTS, the mean detection rate of high signal intensity in hippocampus or amygdala, as seen on FLAIR images was 93%, compared with 43% on spin-echo T2-weighted images. In all cases in which signal intensity on FLAIR images was normal, signal intensity on spin-echo T2-weighted images was also normal. The radiologists preferred the contrast properties of FLAIR to those of spin-echo T2-weighted images. In the diagnosis of MTS using MRI, FLAIR images are more useful for the detection of high signal intensity of hippocampus or amygdala than are spin-echo T2-weighted images. In the diagnosis of MTS, FLAIR imaging is therefore a suitable alternative to spin-echo T2-weighted imaging

Field error lottery

Energy Technology Data Exchange (ETDEWEB)

Elliott, C.J.; McVey, B. (Los Alamos National Lab., NM (USA)); Quimby, D.C. (Spectra Technology, Inc., Bellevue, WA (USA))

1990-01-01

The level of field errors in an FEL is an important determinant of its performance. We have computed 3D performance of a large laser subsystem subjected to field errors of various types. These calculations have been guided by simple models such as SWOOP. The technique of choice is utilization of the FELEX free electron laser code that now possesses extensive engineering capabilities. Modeling includes the ability to establish tolerances of various types: fast and slow scale field bowing, field error level, beam position monitor error level, gap errors, defocusing errors, energy slew, displacement and pointing errors. Many effects of these errors on relative gain and relative power extraction are displayed and are the essential elements of determining an error budget. The random errors also depend on the particular random number seed used in the calculation. The simultaneous display of the performance versus error level of cases with multiple seeds illustrates the variations attributable to stochasticity of this model. All these errors are evaluated numerically for comprehensive engineering of the system. In particular, gap errors are found to place requirements beyond mechanical tolerances of {plus minus}25{mu}m, and amelioration of these may occur by a procedure utilizing direct measurement of the magnetic fields at assembly time. 4 refs., 12 figs.

Wafer-level chip-scale packaging analog and power semiconductor applications

CERN Document Server

Qu, Shichun

2015-01-01

This book presents a state-of-art and in-depth overview in analog and power WLCSP design, material characterization, reliability, and modeling. Recent advances in analog and power electronic WLCSP packaging are presented based on the development of analog technology and power device integration. The book covers in detail how advances in semiconductor content, analog and power advanced WLCSP design, assembly, materials, and reliability have co-enabled significant advances in fan-in and fan-out with redistributed layer (RDL) of analog and power device capability during recent years. Along with new analog and power WLCSP development, the role of modeling is a key to assure successful package design. An overview of the analog and power WLCSP modeling and typical thermal, electrical, and stress modeling methodologies is also provided. This book also: ·         Covers the development of wafer-level power discrete packaging with regular wafer-level design concepts and directly bumping technology ·    �...

Modern Communication: Exploring Physiological Transmission through Tech-Savvy Analogies

Science.gov (United States)

Hollabaugh, Christopher R.; Milanick, Mark A.

2014-01-01

Analogies are often helpful for students to grasp key physiological concepts; sometimes the technical jargon makes the concept seem more complex than it actually is. In this article the authors provide several analogies for information transfer processes that sometimes confuse students. For an analogy to be useful, of course, it needs to be…

AnalogRF and mixed-signal circuit systematic design

CERN Document Server

Tlelo-Cuautle, Esteban; Castro-Lopez, Rafael

2013-01-01

Despite the fact that in the digital domain, designers can take full benefits of IPs and design automation tools to synthesize and design very complex systems, the analog designers’ task is still considered as a ‘handcraft’, cumbersome and very time consuming process. Thus, tremendous efforts are being deployed  to develop new design methodologies in the analog/RF and mixed-signal domains. This book collects 16 state-of-the-art contributions devoted to the topic of systematic design of analog, RF and mixed signal circuits. Divided in the two parts Methodologies and Techniques recent theories, synthesis techniques and design methodologies, as well as new sizing approaches in the field of robust analog and mixed signal design automation are presented for researchers and R/D engineers.  

Proportional and functional analogical reasoning in normal and language-impaired children.

Science.gov (United States)

Nippold, M A; Erskine, B J; Freed, D B

1988-11-01

Teachers often use analogies in classroom settings to clarify new concepts for their students. However, analogies may inadvertently confuse the youngster who has difficulty identifying the one-to-one comparisons underlying them. Although analogical reasoning has been studied extensively in normal children, no information was available concerning this construct in children having a specific language impairment. Thus, it was unknown to what extent they might be deficient in analogical reasoning. Therefore, in the present study, 20 children ages 6-8 years (mean age = 7:6) having normal nonverbal intelligence but deficits in language comprehension were administered tasks of verbal and perceptual proportional analogical reasoning and a problem-solving task of functional analogical reasoning. Compared to a normal-language control group matched on the basis of chronological age and sex, the language-impaired group was deficient in all three tasks of analogical reasoning. However, when the factor of nonverbal intelligence was controlled statistically, the differences between the groups on each of the tasks were removed. Additional findings were that verbal proportional analogical reasoning was significantly correlated to perceptual proportional analogical reasoning and to functional analogical reasoning. Implications for assessment and intervention with young school-age language-impaired children are discussed.

Analogical reasoning and aging: the processing speed and inhibition hypothesis.

Science.gov (United States)

Bugaiska, Aurélia; Thibaut, Jean-Pierre

2015-01-01

This study was designed to investigate the effect of aging on analogical reasoning by manipulating the strength of semantic association (LowAssoc or HighAssoc) and the number of distracters' semantic analogies of the A:B::C:D type and to determine which factors might be responsible for the age-related differences on analogical reasoning by testing two different theoretical frameworks: the inhibition hypothesis and the speed mediation hypothesis. We compared young adults and two groups of aging people (old and old-old) with word analogies of the A:B::C:D format. Results indicate an age-related effect on analogical reasoning, this effect being greatest with LowAssoc analogies. It was not associated with the presence of semantic distractors. Moreover, the results show that the variance part of the analogy task due to age was mainly explained by processing speed (rather than by inhibition) in the case of old participants and by both processing speed and inhibition in the old-old group. These results are discussed in relation to current models of aging and their interaction with the processes involved in analogical reasoning.

Analogy as a means of theoretical adoption of pedagogical disciplines

Directory of Open Access Journals (Sweden)

Solovcova Irina A.

2006-01-01

Full Text Available The paper considers an application of analogy in the initial-teacher training as a tool of approaching pedagogical disciplines. The author proposes a classification of pedagogical analogies which provides choices of the most efficient model for a specific didactic situation. The article clarifies the model of the theoretical approach to pedagogical disciplines through active use of analogy, which contributes to a higher efficiency in a teacher and student interaction. The model consists of three stages: training (the stage of acquiring analogy model, the analytical stage (acquisition of pedagogical concepts, phenomena and systems through the application of analogy, and the stage of self-realization (the application of analogy method in students’ scientific-research activities considering external and internal didactic conditions which transform analogy from a teaching method into a tool for the acquisition of pedagogical disciplines. The author demonstrates that the application of analogy has a positive effect not only on the acquisition of pedagogical knowledge (especially methodic and the development of heuristic skills in students, but also on motivation for the study of pedagogical disciplines (cognitive aspect and professional pedagogical activity (formation of an individual-pedagogical attitude. .

Errors in clinical laboratories or errors in laboratory medicine?

Science.gov (United States)

Plebani, Mario

2006-01-01

Laboratory testing is a highly complex process and, although laboratory services are relatively safe, they are not as safe as they could or should be. Clinical laboratories have long focused their attention on quality control methods and quality assessment programs dealing with analytical aspects of testing. However, a growing body of evidence accumulated in recent decades demonstrates that quality in clinical laboratories cannot be assured by merely focusing on purely analytical aspects. The more recent surveys on errors in laboratory medicine conclude that in the delivery of laboratory testing, mistakes occur more frequently before (pre-analytical) and after (post-analytical) the test has been performed. Most errors are due to pre-analytical factors (46-68.2% of total errors), while a high error rate (18.5-47% of total errors) has also been found in the post-analytical phase. Errors due to analytical problems have been significantly reduced over time, but there is evidence that, particularly for immunoassays, interference may have a serious impact on patients. A description of the most frequent and risky pre-, intra- and post-analytical errors and advice on practical steps for measuring and reducing the risk of errors is therefore given in the present paper. Many mistakes in the Total Testing Process are called "laboratory errors", although these may be due to poor communication, action taken by others involved in the testing process (e.g., physicians, nurses and phlebotomists), or poorly designed processes, all of which are beyond the laboratory's control. Likewise, there is evidence that laboratory information is only partially utilized. A recent document from the International Organization for Standardization (ISO) recommends a new, broader definition of the term "laboratory error" and a classification of errors according to different criteria. In a modern approach to total quality, centered on patients' needs and satisfaction, the risk of errors and mistakes

Synthetic Biology: A Unifying View and Review Using Analog Circuits.

Science.gov (United States)

Teo, Jonathan J Y; Woo, Sung Sik; Sarpeshkar, Rahul

2015-08-01

We review the field of synthetic biology from an analog circuits and analog computation perspective, focusing on circuits that have been built in living cells. This perspective is well suited to pictorially, symbolically, and quantitatively representing the nonlinear, dynamic, and stochastic (noisy) ordinary and partial differential equations that rigorously describe the molecular circuits of synthetic biology. This perspective enables us to construct a canonical analog circuit schematic that helps unify and review the operation of many fundamental circuits that have been built in synthetic biology at the DNA, RNA, protein, and small-molecule levels over nearly two decades. We review 17 circuits in the literature as particular examples of feedforward and feedback analog circuits that arise from special topological cases of the canonical analog circuit schematic. Digital circuit operation of these circuits represents a special case of saturated analog circuit behavior and is automatically incorporated as well. Many issues that have prevented synthetic biology from scaling are naturally represented in analog circuit schematics. Furthermore, the deep similarity between the Boltzmann thermodynamic equations that describe noisy electronic current flow in subthreshold transistors and noisy molecular flux in biochemical reactions has helped map analog circuit motifs in electronics to analog circuit motifs in cells and vice versa via a `cytomorphic' approach. Thus, a body of knowledge in analog electronic circuit design, analysis, simulation, and implementation may also be useful in the robust and efficient design of molecular circuits in synthetic biology, helping it to scale to more complex circuits in the future.

Channel coding for underwater acoustic single-carrier CDMA communication system

Science.gov (United States)

Liu, Lanjun; Zhang, Yonglei; Zhang, Pengcheng; Zhou, Lin; Niu, Jiong

2017-01-01

CDMA is an effective multiple access protocol for underwater acoustic networks, and channel coding can effectively reduce the bit error rate (BER) of the underwater acoustic communication system. For the requirements of underwater acoustic mobile networks based on CDMA, an underwater acoustic single-carrier CDMA communication system (UWA/SCCDMA) based on the direct-sequence spread spectrum is proposed, and its channel coding scheme is studied based on convolution, RA, Turbo and LDPC coding respectively. The implementation steps of the Viterbi algorithm of convolutional coding, BP and minimum sum algorithms of RA coding, Log-MAP and SOVA algorithms of Turbo coding, and sum-product algorithm of LDPC coding are given. An UWA/SCCDMA simulation system based on Matlab is designed. Simulation results show that the UWA/SCCDMA based on RA, Turbo and LDPC coding have good performance such that the communication BER is all less than 10-6 in the underwater acoustic channel with low signal to noise ratio (SNR) from -12 dB to -10dB, which is about 2 orders of magnitude lower than that of the convolutional coding. The system based on Turbo coding with Log-MAP algorithm has the best performance.

Abstract analogical reasoning in high-functioning children with autism spectrum disorders.

Science.gov (United States)

Green, Adam E; Kenworthy, Lauren; Mosner, Maya G; Gallagher, Natalie M; Fearon, Edward W; Balhana, Carlos D; Yerys, Benjamin E

2014-12-01

Children with autism spectrum disorders (ASD) exhibit a deficit in spontaneously recognizing abstract similarities that are crucial for generalizing learning to new situations. This may contribute to deficits in the development of appropriate schemas for navigating novel situations, including social interactions. Analogical reasoning is the central cognitive mechanism that enables typically developing children to understand abstract similarities between different situations. Intriguingly, studies of high-functioning children with ASD point to a relative cognitive strength in basic, nonabstract forms of analogical reasoning. If this analogical reasoning ability extends to abstract analogical reasoning (i.e., between superficially dissimilar situations), it may provide a bridge between a cognitive capability and core ASD deficits in areas such as generalization and categorization. This study tested whether preserved analogical reasoning abilities in ASD can be extended to abstract analogical reasoning, using photographs of real-world items and situations. Abstractness of the analogies was determined via a quantitative measure of semantic distance derived from latent semantic analysis. Children with ASD performed as well as typically developing children at identifying abstract analogical similarities when explicitly instructed to apply analogical reasoning. Individual differences in abstract analogical reasoning ability predicted individual differences in a measure of social function in the ASD group. Preliminary analyses indicated that children with ASD, but not typically developing children, showed an effect of age on abstract analogical reasoning. These results provide new evidence that children with ASD are capable of identifying abstract similarities through analogical reasoning, pointing to abstract analogical reasoning as a potential lever for improving generalization skills and social function in ASD. © 2014 International Society for Autism Research, Wiley

Quantum Analog Computing

Science.gov (United States)

Zak, M.

1998-01-01

Quantum analog computing is based upon similarity between mathematical formalism of quantum mechanics and phenomena to be computed. It exploits a dynamical convergence of several competing phenomena to an attractor which can represent an externum of a function, an image, a solution to a system of ODE, or a stochastic process.

Fast event recorder utilizing a CCD analog shift register

International Nuclear Information System (INIS)

Ducar, R.J.; McIntyre, P.M.

1978-01-01

A system of electronics has been developed to allow the capture and recording of relatively fast, low-amplitude analog events. The heart of the system is a dual 455-cell analog shift register charge-coupled device, Fairchild CCD321ADC-3. The CCD is operated in a dual clock mode. The input is sampled at a selectable clock rate of .25-20 MHz. The stored analog data is then clocked out at a slower rate, typically about .25 MHz. The time base expansion of the analog data allows for analog-to-digital conversion and memory storage using conventional medium-speed devices. The digital data is sequentially loaded into a static RAM and may then be block transferred to a computer. The analog electronics are housed in a single-width NIM module, and the RAM memory in a single-width CAMAC module. Each pair of modules provides six parallel channels. Cost is about $200.00 per channel. Applications are described for ionization imaging (TPC, IRC) and long-drift calorimetry in liquid argon

Electrical analog of a Josephson junction

International Nuclear Information System (INIS)

Goldman, A.M.

1979-01-01

It is noted that a mathematical description of the phase-coupling of two oscillators synchronized by a phase-lock-loop under the influence of thermal white noise is analogous to that of the phase coupling of two superconductors in a Josephson junction also under the influence of noise. This analogy may be useful in studying threshold instabilities of the Josephson junction in regimes not restricted to the case of large damping. This is of interest because the behavior of the mean voltage near the threshold current can be characterized by critical exponents which resemble those exhibited by an order parameter of a continuous phase transition. As it is possible to couple a collection of oscillators together in a chain, the oscillator analogy may also be useful in exploring the dynamics and statistical mechanics of coupled junctions

Understanding the generative capacity of analogies as a tool for explanation

Science.gov (United States)

Wong, E. David

1993-12-01

Psychological studies have typically portrayed analogical reasoning as a process of schema transfer from a familiar domain of understanding to a problem situation. These studies have usually examined analogical reasoning in contexts where (a) individuals possess or have been provided with appropriate, problem-specific schema, (b) the nature of the problem and/or solution is fairly well defined, and (c) ideal analogies are provided or suggested by an outside source. This study examines analogical reasoning in contexts where understanding is generated from loosely organized, incomplete prior knowledge rather than transferred from a well-structured domain of understanding. In addition, participants were asked to create, apply, and modify their own analogies - as opposed to applying a given analogy - as a heuristic for constructing, evaluating, and modifying their explanations for a particular scientific phenomena. The results provide empirical support for the generative properties of analogies; that is, analogies can stimulate new inferences and insight. Furthermore, under specific conditions, individuals can productively harness the generative capacity of their own analogies to advance their conceptual understanding of scientific phenomena.

ERF/ERFC, Calculation of Error Function, Complementary Error Function, Probability Integrals

International Nuclear Information System (INIS)

Vogel, J.E.

1983-01-01

1 - Description of problem or function: ERF and ERFC are used to compute values of the error function and complementary error function for any real number. They may be used to compute other related functions such as the normal probability integrals. 4. Method of solution: The error function and complementary error function are approximated by rational functions. Three such rational approximations are used depending on whether - x .GE.4.0. In the first region the error function is computed directly and the complementary error function is computed via the identity erfc(x)=1.0-erf(x). In the other two regions the complementary error function is computed directly and the error function is computed from the identity erf(x)=1.0-erfc(x). The error function and complementary error function are real-valued functions of any real argument. The range of the error function is (-1,1). The range of the complementary error function is (0,2). 5. Restrictions on the complexity of the problem: The user is cautioned against using ERF to compute the complementary error function by using the identity erfc(x)=1.0-erf(x). This subtraction may cause partial or total loss of significance for certain values of x

Transistor analogs of emergent iono-neuronal dynamics.

Science.gov (United States)

Rachmuth, Guy; Poon, Chi-Sang

2008-06-01

Neuromorphic analog metal-oxide-silicon (MOS) transistor circuits promise compact, low-power, and high-speed emulations of iono-neuronal dynamics orders-of-magnitude faster than digital simulation. However, their inherently limited input voltage dynamic range vs power consumption and silicon die area tradeoffs makes them highly sensitive to transistor mismatch due to fabrication inaccuracy, device noise, and other nonidealities. This limitation precludes robust analog very-large-scale-integration (aVLSI) circuits implementation of emergent iono-neuronal dynamics computations beyond simple spiking with limited ion channel dynamics. Here we present versatile neuromorphic analog building-block circuits that afford near-maximum voltage dynamic range operating within the low-power MOS transistor weak-inversion regime which is ideal for aVLSI implementation or implantable biomimetic device applications. The fabricated microchip allowed robust realization of dynamic iono-neuronal computations such as coincidence detection of presynaptic spikes or pre- and postsynaptic activities. As a critical performance benchmark, the high-speed and highly interactive iono-neuronal simulation capability on-chip enabled our prompt discovery of a minimal model of chaotic pacemaker bursting, an emergent iono-neuronal behavior of fundamental biological significance which has hitherto defied experimental testing or computational exploration via conventional digital or analog simulations. These compact and power-efficient transistor analogs of emergent iono-neuronal dynamics open new avenues for next-generation neuromorphic, neuroprosthetic, and brain-machine interface applications.

Emergent Explorations: Analog and Digital Scripting

OpenAIRE

Worden, Alexander

2011-01-01

This book documents an exploration of emergent and linear modes of defining space, form, and structure. The thesis highlights a dialog between analog and digital modeling techniques, in concept and project development. It identifies that analog modeling techniques, coupled with judgment, can be used to develop complex forms. The thesis project employs critical judgment and the textile techniques of crochet as a vehicle generate form. Crochet lends itself to this investigation because it ...

Contrast-enhanced Magnetic Resonance Imaging of Pelvic Bone Metastases at 3.0 T: Comparison Between 3-dimensional T1-weighted CAIPIRINHA-VIBE Sequence and 2-dimensional T1-weighted Turbo Spin-Echo Sequence.

Science.gov (United States)

Yoon, Min A; Hong, Suk-Joo; Lee, Kyu-Chong; Lee, Chang Hee

2018-06-12

This study aimed to compare 3-dimensional T1-weighted gradient-echo sequence (CAIPIRINHA-volumetric interpolated breath-hold examination [VIBE]) with 2-dimensional T1-weighted turbo spin-echo sequence for contrast-enhanced magnetic resonance imaging (MRI) of pelvic bone metastases at 3.0 T. Thirty-one contrast-enhanced MRIs of pelvic bone metastases were included. Two contrast-enhanced sequences were evaluated for the following parameters: overall image quality, sharpness of pelvic bone, iliac vessel clarity, artifact severity, and conspicuity and edge sharpness of the smallest metastases. Quantitative analysis was performed by calculating signal-to-noise ratio and contrast-to-noise ratio of the smallest metastases. Significant differences between the 2 sequences were assessed. CAIPIRINHA-VIBE had higher scores for overall image quality, pelvic bone sharpness, iliac vessel clarity, and edge sharpness of the metastatic lesions, and had less artifacts (all P 0.05). Our results suggest that CAIPIRINHA-VIBE may be superior to turbo spin-echo for contrast-enhanced MRI of pelvic bone metastases at 3.0 T.

Young Children's Analogical Reasoning in Science Domains

Science.gov (United States)

Haglund, Jesper; Jeppsson, Fredrik; Andersson, Johanna

2012-01-01

This exploratory study in a classroom setting investigates first graders' (age 7-8 years, N = 25) ability to perform analogical reasoning and create their own analogies for two irreversible natural phenomena: mixing and heat transfer. We found that the children who contributed actively to a full-class discussion were consistently successful at…

Children's Use of Analogy during Collaborative Reasoning

Science.gov (United States)

Lin, Tzu-Jung; Anderson, Richard C.; Hummel, John E.; Jadallah, May; Miller, Brian W.; Nguyen-Jahiel, Kim; Morris, Joshua A.; Kuo, Li-Jen; Kim, Il-Hee; Wu, Xiaoying; Dong, Ting

2012-01-01

This microgenetic study examined social influences on children's development of analogical reasoning during peer-led small-group discussions of stories about controversial issues. A total of 277 analogies were identified among 7,215 child turns for speaking during 54 discussions from 18 discussion groups in 6 fourth-grade classrooms (N = 120; age…

A methodology for translating positional error into measures of attribute error, and combining the two error sources

Science.gov (United States)

Yohay Carmel; Curtis Flather; Denis Dean

2006-01-01

This paper summarizes our efforts to investigate the nature, behavior, and implications of positional error and attribute error in spatiotemporal datasets. Estimating the combined influence of these errors on map analysis has been hindered by the fact that these two error types are traditionally expressed in different units (distance units, and categorical units,...

Analogical Reasoning in the Engineering Design Process and Technology Education Applications

Science.gov (United States)

Daugherty, Jenny; Mentzer, Nathan

2008-01-01

This synthesis paper discusses the research exploring analogical reasoning, the role of analogies in the engineering design process, and educational applications for analogical reasoning. Researchers have discovered that analogical reasoning is often a fundamental cognitive tool in design problem solving. Regarding the possible role of analogical…

Magnetic resonance imaging of anterior cruciate ligament of the knee: a comparison of four sequences

International Nuclear Information System (INIS)

Casillas, C.; Marti-Bonmati, L.; Molla, E.; Ferrer, P.; Dosda, R.

1999-01-01

To compare the diagnostic efficacy of the four magnetic resonance imaging (MRI) sequences that compose the standard protocol for the study of the knee in our center when employed in the examination of anterior cruciate ligament (ACL). A prospective study was carried out based on MRI findings in the knees of 326 consecutive patients. Sagittal [proton density (PD w eighted turbo-spin-echo and T2*-weighted gradient echo], coronal (PD-weighted turbo-spin-echo with fat suppression) and transverse (T2*-weighted gradient echo with magnetization transfer) images were evaluated. Each sequence was analyzed independently by two radiologists, while another two assessed all the sequences together with the clinical findings. Four categories were established: normal ACL, partially torn, completely torn and synovialized. The sensitivity, specificity, positive predictive value (PPV) and negative predictive value (NPV) with respect to the definitive diagnosis were calculated for each sequence. The statistical analysis of the findings for each category was done using the chi-squared test and the Kappa test was employed to assess the degree of agreement. According to the final diagnosis, 263 ACL were normal, 29 were partially torn, 33 were completely torn and there was 1 case of synovialization associated with a completely torn ACL. The relationship between the analysis of the ACL according to each sequence and the definitive diagnosis was very significant (p<0.001) and the agreement was excellent. All the sequences presented similar levels of diagnostic precision. The coronal sequence had least number of diagnostic errors (2.1%). The combinations of imaging techniques that resulted in the lowest error rate with respect to the definitive diagnosis were coronal PD-weighted turbo-spin-echo with fat suppression and sagittal PD-weighted turbo-spin-echo. Coronal images are highly precise in the evaluation of ACL. Sagittal sequences are the most valid for diagnosis of torn ACL. Transverse

Magnetic resonance imaging of anterior cruciate ligament of the knee: a comparison of four sequences; Valoracion del ligamento cruzado anterior de la rodilla con RM: comparacion de cuatro secuencias

Energy Technology Data Exchange (ETDEWEB)

Casillas, C.; Marti-Bonmati, L.; Molla, E.; Ferrer, P.; Dosda, R. [Clinical Quiron-ATQ. Valencia (Spain)

1999-07-01

To compare the diagnostic efficacy of the four magnetic resonance imaging (MRI) sequences that compose the standard protocol for the study of the knee in our center when employed in the examination of anterior cruciate ligament (ACL). A prospective study was carried out based on MRI findings in the knees of 326 consecutive patients. Sagittal [proton density (PD{sub w}eighted turbo-spin-echo and T2*-weighted gradient echo], coronal (PD-weighted turbo-spin-echo with fat suppression) and transverse (T2*-weighted gradient echo with magnetization transfer) images were evaluated. Each sequence was analyzed independently by two radiologists, while another two assessed all the sequences together with the clinical findings. Four categories were established: normal ACL, partially torn, completely torn and synovialized. The sensitivity, specificity, positive predictive value (PPV) and negative predictive value (NPV) with respect to the definitive diagnosis were calculated for each sequence. The statistical analysis of the findings for each category was done using the chi-squared test and the Kappa test was employed to assess the degree of agreement. According to the final diagnosis, 263 ACL were normal, 29 were partially torn, 33 were completely torn and there was 1 case of synovialization associated with a completely torn ACL. The relationship between the analysis of the ACL according to each sequence and the definitive diagnosis was very significant (p<0.001) and the agreement was excellent. All the sequences presented similar levels of diagnostic precision. The coronal sequence had least number of diagnostic errors (2.1%). The combinations of imaging techniques that resulted in the lowest error rate with respect to the definitive diagnosis were coronal PD-weighted turbo-spin-echo with fat suppression and sagittal PD-weighted turbo-spin-echo. Coronal images are highly precise in the evaluation of ACL. Sagittal sequences are the most valid for diagnosis of torn ACL

Statistical errors in Monte Carlo estimates of systematic errors

Science.gov (United States)

Roe, Byron P.

2007-01-01

For estimating the effects of a number of systematic errors on a data sample, one can generate Monte Carlo (MC) runs with systematic parameters varied and examine the change in the desired observed result. Two methods are often used. In the unisim method, the systematic parameters are varied one at a time by one standard deviation, each parameter corresponding to a MC run. In the multisim method (see ), each MC run has all of the parameters varied; the amount of variation is chosen from the expected distribution of each systematic parameter, usually assumed to be a normal distribution. The variance of the overall systematic error determination is derived for each of the two methods and comparisons are made between them. If one focuses not on the error in the prediction of an individual systematic error, but on the overall error due to all systematic errors in the error matrix element in data bin m, the number of events needed is strongly reduced because of the averaging effect over all of the errors. For simple models presented here the multisim model was far better if the statistical error in the MC samples was larger than an individual systematic error, while for the reverse case, the unisim model was better. Exact formulas and formulas for the simple toy models are presented so that realistic calculations can be made. The calculations in the present note are valid if the errors are in a linear region. If that region extends sufficiently far, one can have the unisims or multisims correspond to k standard deviations instead of one. This reduces the number of events required by a factor of k2. The specific terms unisim and multisim were coined by Peter Meyers and Steve Brice, respectively, for the MiniBooNE experiment. However, the concepts have been developed over time and have been in general use for some time.

Global orbit feedback utilizing analog and digital technologies

International Nuclear Information System (INIS)

Singh, O.; Tang, Y.; Ramamoorthy, S.; Krinsky, S.; Yu, L.H.

1997-01-01

At the NSLS, an analog global orbit feedback system is used in regular operations, and a digital global orbit feedback system is available in machine physics studies on the X-Ray Ring. Here, the authors discuss the relative merits of utilizing analog and digital technology in orbit feedback. Results of experiments are reported characterizing the performance of the analog and digital systems when operated individually or together. They give their thoughts on plans for future development of the orbit feedback systems at the NSLS

Effects of Multimedia and Schema Induced Analogical Reasoning on Science Learning

Science.gov (United States)

Zheng, R. Z.; Yang, W.; Garcia, D.; McCadden, E. P.

2008-01-01

The present study investigates the effects of multimedia and schema induced analogical reasoning on science learning. It involves 89 fourth grade elementary students in the north-east of the United States. Participants are randomly assigned into four conditions: (a) multimedia with analogy; (b) multimedia without analogy; (c) analogy without…

An analog integrated circuit design laboratory

OpenAIRE

Mondragon-Torres, A.F.; Mayhugh, Jr.; Pineda de Gyvez, J.; Silva-Martinez, J.; Sanchez-Sinencio, E.

2003-01-01

We present the structure of an analog integrated circuit design laboratory to instruct at both, senior undergraduate and entry graduate levels. The teaching material includes: a laboratory manual with analog circuit design theory, pre-laboratory exercises and circuit design specifications; a reference web page with step by step instructions and examples; the use of mathematical tools for automation and analysis; and state of the art CAD design tools in use by industry. Upon completion of the ...

On Lovelock analogs of the Riemann tensor

Science.gov (United States)

Camanho, Xián O.; Dadhich, Naresh

2016-03-01

It is possible to define an analog of the Riemann tensor for Nth order Lovelock gravity, its characterizing property being that the trace of its Bianchi derivative yields the corresponding analog of the Einstein tensor. Interestingly there exist two parallel but distinct such analogs and the main purpose of this note is to reconcile both formulations. In addition we will introduce a simple tensor identity and use it to show that any pure Lovelock vacuum in odd d=2N+1 dimensions is Lovelock flat, i.e. any vacuum solution of the theory has vanishing Lovelock-Riemann tensor. Further, in the presence of cosmological constant it is the Lovelock-Weyl tensor that vanishes.

A Simplified Top-Oil Temperature Model for Transformers Based on the Pathway of Energy Transfer Concept and the Thermal-Electrical Analogy

Directory of Open Access Journals (Sweden)

Muhammad Hakirin Roslan

2017-11-01

Full Text Available This paper presents an alternative approach to determine the simplified top-oil temperature (TOT based on the pathway of energy transfer and thermal-electrical analogy concepts. The main contribution of this study is the redefinition of the nonlinear thermal resistance based on these concepts. An alternative approximation of convection coefficient, h, based on heat transfer theory was proposed which eliminated the requirement of viscosity. In addition, the lumped capacitance method was applied to the thermal-electrical analogy to derive the TOT thermal equivalent equation in differential form. The TOT thermal model was evaluated based on the measured TOT of seven transformers with either oil natural air natural (ONAN or oil natural air forced (ONAF cooling modes obtained from temperature rise tests. In addition, the performance of the TOT thermal model was tested on step-loading of a transformer with an ONAF cooling mode obtained from previous studies. A comparison between the TOT thermal model and the existing TOT Thermal-Electrical, Exponential (IEC 60076-7, and Clause 7 (IEEE C57.91-1995 models was also carried out. It was found that the measured TOT of seven transformers are well represented by the TOT thermal model where the highest maximum and root mean square (RMS errors are 6.66 °C and 2.76 °C, respectively. Based on the maximum and RMS errors, the TOT thermal model performs better than Exponential and Clause 7 models and it is comparable with the Thermal-Electrical 1 (TE1 and Thermal-Electrical 2 (TE2 models. The same pattern is found for the TOT thermal model under step-loading where the maximum and RMS errors are 5.77 °C and 2.02 °C.

Analogies in high school Brazilian chemistry textbooks

Directory of Open Access Journals (Sweden)

Rosária Justi

2000-05-01

Full Text Available This paper presents and discusses an analysis of the analogies presented by Brazilian chemistry textbooks for the medium level. The main aim of the analysis is to discuss whether such analogies can be said good teaching models. From the results, some aspects concerning with teachers' role are discussed. Finally, some new research questions are emphasised.

Analogy, an Alternative Model.
 Critics to the standard model of analogical problems solving and proposals for an alternative one

Directory of Open Access Journals (Sweden)

Ricardo A. Minervino

2016-02-01

Full Text Available The authors made an extension of Hofstadter‘s criticisms against the standard approach in analogical thinking represented by the structure-mapping theory of Gentner and the multiconstraint theory of Holyoak and Thagard. Based on this extension, they proposed a non-serial model of analogical problem solving. Against the standard approach, the model postulates that: (a people detect and evaluate differences between mapped elements before the subprocess of inference generation and consider them in order to control it, and (b properties of an element that explain why the element could fill a certain role in the base problem resolution (PERs play a crucial role in these detection and evaluation operations, and also in post-inferences subprocesses. An experiment showed that: (a people detect and evaluate the relevance of differences between mapped elements before inference generation, (b that they inhibit the generation of literal inferences when they face relevant differences, and (c that they stop the subprocess when they recognize insuperable ones. The results also showed that base PERs are reactivated at different moments of analogical transfer. The data obtained are incompatible with the standard theories of analogical thinking, which treat inference generation as a syntactic mechanism and exclude contextual semantic analysis from the study of analogy. 

The making of analog module for gamma camera interface

International Nuclear Information System (INIS)

Yulinarsari, Leli; Rl, Tjutju; Susila, Atang; Sukandar

2003-01-01

The making of an analog module for gamma camera has been conducted. For computerization of planar gamma camera 37 PMT it has been developed interface hardware technology and software between the planar gamma camera with PC. With this interface gamma camera image information (Originally analog signal) was changed to digital single, therefore processes of data acquisition, image quality increase and data analysis as well as data base processing can be conducted with the help of computers, there are three gamma camera main signals, i.e. X, Y and Z . This analog module makes digitation of analog signal X and Y from the gamma camera that conveys position information coming from the gamma camera crystal. Analog conversion to digital was conducted by 2 converters ADC 12 bit with conversion time 800 ns each, conversion procedure for each coordinate X and Y was synchronized using suitable strobe signal Z for information acceptance

Medication Errors - A Review

OpenAIRE

Vinay BC; Nikhitha MK; Patel Sunil B

2015-01-01

In this present review article, regarding medication errors its definition, medication error problem, types of medication errors, common causes of medication errors, monitoring medication errors, consequences of medication errors, prevention of medication error and managing medication errors have been explained neatly and legibly with proper tables which is easy to understand.

Children's analogical reasoning in a third-grade science discussion

Science.gov (United States)

May, David B.; Hammer, David; Roy, Patricia

2006-03-01

Expert scientific inquiry involves the generation and use of analogies. How and when students might develop this aspect of expertise has implications for understanding how and when instruction might facilitate that development. In a study of K-8 student inquiry in physical science, we are examining cases of spontaneous analogy generation. In the case we present here, a third-grader generates an analogy and modifies it to reconcile his classmates' counterarguments, allowing us to identify in these third-graders specific aspects of nascent expertise in analogy use. Promoting abilities and inclinations such as these children display requires that educators recognize and respond to them.

Leibniz y el concepto de analogía

Directory of Open Access Journals (Sweden)

Oscar Miguel Esquisabel

2008-11-01

Full Text Available In this paper an analysis of the leibnizian applications of conceptof analogy as well as the analogical reasoning is approached. Thus, the analysis tries to show that the leibnizian concept of analogy is based on the idea of structural similarity. As a consequence of such consideration,two basic ways in which Leibniz applies analogical reasoning are examined. The first way has a conjectural character and is rather heuristic, whereas the second constitutes, at least in intention, a kind of demonstrative analogicalreasoning, since it tries to prove its conclusions for a determined theoreticaldomain by applying a transfer principle, which is itself founded on the identity of structural properties.This procedure is exemplified by outlining the leibnizian view on contingent truths. In this way, the paper concludesby pointing out the theoretical relevance of the concept of similarity in theleibnizian thought.

The Discourse on Printed and Electronic Books: Analogies, Oppositions, and Perspectives

Science.gov (United States)

Velagic, Zoran

2014-01-01

Introduction: The point of departure for this paper is the twofold analogy (analogy of content, analogy of medium) between printed and electronic books, the aim being to draw attention to the usual perception of their capacities and relationships, to provide a rather detailed analysis of the outcome and sustainability of such analogies and…

Source selection for analogical reasoning an empirical approach

Energy Technology Data Exchange (ETDEWEB)

Stubblefield, W.A. [Sandia National Labs., Albuquerque, NM (United States); Luger, G.F. [Univ. of New Mexico, Albuquerque, NM (United States)

1996-12-31

The effectiveness of an analogical reasoner depends upon its ability to select a relevant analogical source. In many problem domains, however, too little is known about target problems to support effective source selection. This paper describes the design and evaluation of SCAVENGER, an analogical reasoner that applies two techniques to this problem: (1) An assumption-based approach to matching that allows properties of candidate sources to match unknown target properties in the absence of evidence to the contrary. (2) The use of empirical learning to improve memory organization based on problem solving experience.

Error Patterns

NARCIS (Netherlands)

Hoede, C.; Li, Z.

2001-01-01

In coding theory the problem of decoding focuses on error vectors. In the simplest situation code words are $(0,1)$-vectors, as are the received messages and the error vectors. Comparison of a received word with the code words yields a set of error vectors. In deciding on the original code word,

Creative Analogy Use in a Heterogeneous Design Team

DEFF Research Database (Denmark)

Christensen, Bo; Ball, Linden J.

2016-01-01

the design dialogue derived from team members with highly disparate educational backgrounds. Our analyses revealed that analogies that matched (versus mismatched) educational backgrounds were generated and revisited more frequently, presumably because they were more accessible. Matching analogies were also...

The error in total error reduction.

Science.gov (United States)

Witnauer, James E; Urcelay, Gonzalo P; Miller, Ralph R

2014-02-01

Most models of human and animal learning assume that learning is proportional to the discrepancy between a delivered outcome and the outcome predicted by all cues present during that trial (i.e., total error across a stimulus compound). This total error reduction (TER) view has been implemented in connectionist and artificial neural network models to describe the conditions under which weights between units change. Electrophysiological work has revealed that the activity of dopamine neurons is correlated with the total error signal in models of reward learning. Similar neural mechanisms presumably support fear conditioning, human contingency learning, and other types of learning. Using a computational modeling approach, we compared several TER models of associative learning to an alternative model that rejects the TER assumption in favor of local error reduction (LER), which assumes that learning about each cue is proportional to the discrepancy between the delivered outcome and the outcome predicted by that specific cue on that trial. The LER model provided a better fit to the reviewed data than the TER models. Given the superiority of the LER model with the present data sets, acceptance of TER should be tempered. Copyright © 2013 Elsevier Inc. All rights reserved.

Electronic devices for analog signal processing

CERN Document Server

Rybin, Yu K

2012-01-01

Electronic Devices for Analog Signal Processing is intended for engineers and post graduates and considers electronic devices applied to process analog signals in instrument making, automation, measurements, and other branches of technology. They perform various transformations of electrical signals: scaling, integration, logarithming, etc. The need in their deeper study is caused, on the one hand, by the extension of the forms of the input signal and increasing accuracy and performance of such devices, and on the other hand, new devices constantly emerge and are already widely used in practice, but no information about them are written in books on electronics. The basic approach of presenting the material in Electronic Devices for Analog Signal Processing can be formulated as follows: the study with help from self-education. While divided into seven chapters, each chapter contains theoretical material, examples of practical problems, questions and tests. The most difficult questions are marked by a diamon...

Synthesis and anti-inflammatory activity of phenylbutenoid dimer analogs

International Nuclear Information System (INIS)

Kim, Sung Soo; Fang, Yuan Ying; Park, Hae Eil

2015-01-01

Several phenylbutenoid dimer (PBD) analogs were synthesized and evaluated for their inhibitory activities against nitric oxide (NO) production and TNF-α release. The PBD analogs were synthesized via Diels–Alder and subsequent Schlosser reactions as key steps. Among the tested compounds, two analogs (8c, 8f) exhibited much stronger inhibitory activity against LPS-stimulated NO production and TNF-α release in RAW 264.7 cells than that of wogonin

BERAS ANALOG SEBAGAI PANGAN FUNGSIONAL DENGAN INDEKS GLIKEMIK RENDAH

Directory of Open Access Journals (Sweden)

Santi Noviasari

2016-04-01

Full Text Available ABSTRACTThe objective of this research was to produce rice analogue as functional food with low glycemic index. The rice was made from white corn and sorghum with additional soybean flour. The physicochemical properties of rice analogue being analysed were resistant starch content, total phenolic content, dietary fiber, color (L*, +a, +b values and whiteness (oHue. Rice analogue was potentially used as functional food indicated by high level of resistant starch 2.59%-3.31%, total phenolic content 0.18-0.25 mg GAE/g sample and dietary fiber 5.35%-6.14%. Rice analogue from white corn with and without soybean flour was further tested for glycemic index. Rice analogue from white corn has 69 GI value, while rice analogue from white corn with 10% soybean flour addition has 50 GI value.Keywords: functional food, glycemic index, rice analogueABSTRAKTujuan penelitian ini adalah untuk mendapatkan beras analog yang berpotensi sebagai pangan fungsional dan bernilai indeks glikemik rendah. Beras analog dibuat dari bahan baku jagung putih dan sorgum dengan penambahan tepung kedelai. Sifat fisiko kimia beras analog yang dianalisis adalah pati resisten, total fenol, serat pangan, warna (nilai L*, +a, +b dan derajat putih (oHue. Beras analog berpotensi sebagai pangan fungsional, yang ditunjukkan dengan tingginya kadar pati resisten yaitu sebanyak 2,59%-3,31%, total fenol sekitar 0,18-0,25 mg GAE/g sampel dan serat pangan antara 5,35%-6,14%. Beras analog berbahan baku jagung putih dengan dan tanpa penambahan kedelai dipilih untuk uji indeks glikemik. Beras analog dari jagung putih memiliki nilai IG 69 sedangkan beras analog dari jagung putih dengan penambahan tepung kedelai 10% memiliki nilai IG 50.Kata kunci: beras analog, indeks glikemik, pangan fungsional

Characteristics of pediatric chemotherapy medication errors in a national error reporting database.

Science.gov (United States)

Rinke, Michael L; Shore, Andrew D; Morlock, Laura; Hicks, Rodney W; Miller, Marlene R

2007-07-01

Little is known regarding chemotherapy medication errors in pediatrics despite studies suggesting high rates of overall pediatric medication errors. In this study, the authors examined patterns in pediatric chemotherapy errors. The authors queried the United States Pharmacopeia MEDMARX database, a national, voluntary, Internet-accessible error reporting system, for all error reports from 1999 through 2004 that involved chemotherapy medications and patients aged error reports, 85% reached the patient, and 15.6% required additional patient monitoring or therapeutic intervention. Forty-eight percent of errors originated in the administering phase of medication delivery, and 30% originated in the drug-dispensing phase. Of the 387 medications cited, 39.5% were antimetabolites, 14.0% were alkylating agents, 9.3% were anthracyclines, and 9.3% were topoisomerase inhibitors. The most commonly involved chemotherapeutic agents were methotrexate (15.3%), cytarabine (12.1%), and etoposide (8.3%). The most common error types were improper dose/quantity (22.9% of 327 cited error types), wrong time (22.6%), omission error (14.1%), and wrong administration technique/wrong route (12.2%). The most common error causes were performance deficit (41.3% of 547 cited error causes), equipment and medication delivery devices (12.4%), communication (8.8%), knowledge deficit (6.8%), and written order errors (5.5%). Four of the 5 most serious errors occurred at community hospitals. Pediatric chemotherapy errors often reached the patient, potentially were harmful, and differed in quality between outpatient and inpatient areas. This study indicated which chemotherapeutic agents most often were involved in errors and that administering errors were common. Investigation is needed regarding targeted medication administration safeguards for these high-risk medications. Copyright (c) 2007 American Cancer Society.

Nitrate analogs as attractants for soybean cyst nematode.

Science.gov (United States)

Hosoi, Akito; Katsuyama, Tsutomu; Sasaki, Yasuyuki; Kondo, Tatsuhiko; Yajima, Shunsuke; Ito, Shinsaku

2017-08-01

Soybean cyst nematode (SCN) Heterodera glycines Ichinohe, a plant parasite, is one of the most serious pests of soybean. In this paper, we report that SCN is attracted to nitrate and its analogs. We performed attraction assays to screen for novel attractants for SCN and found that nitrates were attractants for SCN and SCN recognized nitrate gradients. However, attraction of SCN to nitrates was not observed on agar containing nitrate. To further elucidate the attraction mechanism in SCN, we performed attraction assays using nitrate analogs ([Formula: see text], [Formula: see text], [Formula: see text]). SCN was attracted to all nitrate analogs; however, attraction of SCN to nitrate analogs was not observed on agar containing nitrate. In contrast, SCN was attracted to azuki root, irrespective of presence or absence of nitrate in agar media. Our results suggest that the attraction mechanisms differ between plant-derived attractant and nitrate.

Reference-Free CMOS Pipeline Analog-to-Digital Converters

CERN Document Server

Figueiredo, Michael; Evans, Guiomar

2013-01-01

This book shows that digitally assisted analog-to-digital converters are not the only way to cope with poor analog performance caused by technology scaling. It describes various analog design techniques that enhance the area and power efficiency without employing any type of digital calibration circuitry. These techniques consist of self-biasing for PVT enhancement, inverter-based design for improved speed/power ratio, gain-of-two obtained by voltage sum instead of charge redistribution, and current-mode reference shifting instead of voltage reference shifting. Together, these techniques allow enhancing the area and power efficiency of the main building blocks of a multiplying digital-to-analog converter (MDAC) based stage, namely, the flash quantizer, the amplifier, and the switched capacitor network of the MDAC. Complementing the theoretical analyses of the various techniques, a power efficient operational transconductance amplifier is implemented and experimentally characterized. Furthermore, a medium-low ...

When Reasoning Modifies Memory: Schematic Assimilation Triggered by Analogical Mapping

Science.gov (United States)

Vendetti, Michael S.; Wu, Aaron; Rowshanshad, Ebi; Knowlton, Barbara J.; Holyoak, Keith J.

2014-01-01

Analogical mapping highlights shared relations that link 2 situations, potentially at the expense of information that does not fit the dominant pattern of correspondences. To investigate whether analogical mapping can alter subsequent recognition memory for features of a source analog, we performed 2 experiments with 4-term proportional analogies…

Turbo machine tip clearance and vibration measurements using a fibre optic laser Doppler position sensor

Science.gov (United States)

Pfister, T.; Büttner, L.; Czarske, J.; Krain, H.; Schodl, R.

2006-07-01

This paper presents a novel fibre optic laser Doppler position sensor for single blade tip clearance and vibration measurements at turbo machines, which offers high temporal resolution and high position resolution simultaneously. The sensor principle is based on the generation of a measurement volume consisting of two superposed fan-like interference fringe systems with contrary fringe spacing gradients using wavelength division multiplexing. A flexible and robust measurement system with an all-passive fibre coupled measurement head has been realized employing diffractive and refractive optics. Measurements of tip clearance and rotor vibrations at a transonic centrifugal compressor performed during operation at up to 50 000 rpm (833 Hz) corresponding to 21.7 kHz blade frequency and 586 m s-1 blade tip velocity are presented. The results are in excellent agreement with those of capacitive probes. The mean uncertainty of the position measurement was around 20 µm and, thus, considerably better than for conventional tip clearance probes. Consequently, this sensor is capable of fulfilling the requirements for future active clearance control systems and has great potential for in situ and online tip clearance and vibration measurements at metallic and non-metallic turbine blades with high precision.

A heat exchanger analogy of automotive paint ovens