Graphics-based site information management at Hanford TRU burial grounds

International Nuclear Information System (INIS)

Rod, S.R.

1992-01-01

The objective of the project described in this paper is to demonstrate the use of integrated computer graphics and data base techniques in managing nuclear waste facilities. The graphics-based site information management system (SIMS) combines a three-dimensional graphic model of the facility with databases which describe the facility's components and waste inventory. The SIMS can create graphic visualizations of any site data. The SIMS described here is being used by Westinghouse Hanford Company (WHC) as part of its transuranic (TRU) waste retrieval program at the Hanford Reservation. It is being used to manage an inventory of over 38,000 containers, to validate records, and to help visualize conceptual designs of waste retrieval operations

Water budget for SRP burial ground area

International Nuclear Information System (INIS)

Hubbard, J.E.; Emslie, R.H.

1984-01-01

Radionuclide migration from the SRP burial ground for solid low-level waste has been studied extensively. Most of the buried radionuclides are fixed on the soil and show negligible movement. The major exception is tritium, which when leached from the waste by percolating rainfall, forms tritiated water and moves with the groundwater. The presence of tritium has been useful in tracing groundwater flow paths to outcrop. A subsurface tritium plume moving from the southwest corner of the burial ground toward an outcrop near Four Mile Creek has been defined. Groundwater movement is so slow that much of the tritium decays before reaching the outcrop. The burial ground tritium plume defined to date is virtually all in the uppermost sediment layer, the Barnwell Formation. The purpose of the study reported in this memorandum was to investigate the hypothesis that deeper flow paths, capable of carrying substantial amounts of tritium, may exist in the vicinity of the burial ground. As a first step in seeking deeper flow paths, a water budget was constructed for the burial ground site. The water budget, a materials balance used by hydrologists, is expressed in annual area inches of rainfall. Components of the water budget for the burial ground area were analyzed to determine whether significant flow paths may exist below the tan clay. Mean annual precipitation was estimated as 47 inches, with evapotranspiration, run-off, and groundwater recharge estimated as 30, 2, and 15 inches, respectively. These estimates, when combined with groundwater discharge data, suggest that 5 inches of the groundwater recharge flow above the tan clay and that 10 inches flow below the tan clay. Therefore, two-thirds of the groundwater recharge appears to follow flow paths that are deeper than those previously found. 13 references, 10 figures, 5 tables

Tritium in the burial ground of the Savannah River Site

International Nuclear Information System (INIS)

Hyder, M.L.

1993-06-01

This memorandum reviews the available information on tritium-contaminated material discarded to burial grounds. Tritium was the first isotope studied because it represents the most immediate concern with regard to release to the environment. Substantial amounts of tritium are known to be present in the ground water underneath the area, and outcropping of this ground water in springs and seeps has been observed. The response to this release of tritium from the burial ground is a current concern. The amount of tritium emplaced in the burial ground facilities is very uncertain, however, some general conclusions can be made. In particular, most of the tritium buried is associated with spent equipment and other waste, rather than spent melts. Correspondingly, most of the tritium in the ground water seems to be associated with burials of this type, rather than the spent melts. Maps are presented showing the location of burials of tritiated waste by type, and the location of the largest individual burials according to COBRA records

Cleanup Verification Package for the 618-8 Burial Ground

International Nuclear Information System (INIS)

Appel, M.J.

2006-01-01

This cleanup verification package documents completion of remedial action for the 618-8 Burial Ground, also referred to as the Solid Waste Burial Ground No. 8, 318-8, and the Early Solid Waste Burial Ground. During its period of operation, the 618-8 site is speculated to have been used to bury uranium-contaminated waste derived from fuel manufacturing, and construction debris from the remodeling of the 313 Building

Cleanup Verification Package for the 618-3 Burial Ground

International Nuclear Information System (INIS)

Appel, M.J.

2006-01-01

This cleanup verification package documents completion of remedial action for the 618-3 Solid Waste Burial Ground, also referred to as Burial Ground Number 3 and the Dry Waste Burial Ground Number 3. During its period of operation, the 618-3 site was used to dispose of uranium-contaminated construction debris from the 311 Building and construction/demolition debris from remodeling of the 313, 303-J and 303-K Buildings

Cleanup Verification Package for the 118-F-1 Burial Ground

Energy Technology Data Exchange (ETDEWEB)

E. J. Farris and H. M. Sulloway

2008-01-10

This cleanup verification package documents completion of remedial action for the 118-F-1 Burial Ground on the Hanford Site. This burial ground is a combination of two locations formerly called Minor Construction Burial Ground No. 2 and Solid Waste Burial Ground No. 2. This waste site received radioactive equipment and other miscellaneous waste from 105-F Reactor operations, including dummy elements and irradiated process tubing; gun barrel tips, steel sleeves, and metal chips removed from the reactor; filter boxes containing reactor graphite chips; and miscellaneous construction solid waste.

618-11 Burial Ground USRADS radiological surveys

International Nuclear Information System (INIS)

Wendling, M.A.

1994-01-01

This report summarizes and documents the results of the radiological surveys conducted from February 4 through February 10, 1993 over the 618-11 Burial Ground, Hanford Site, Richland, Washington. In addition, this report explains the survey methodology using the Ultrasonic Ranging and Data System (USRADS). The 618-11 Burial Ground radiological survey field task consisted of two activities: characterization of the specific background conditions and the radiological survey of the area. The radiological survey of the 618-11 Burial Ground, along with the background study, were conducted by Site Investigative Surveys Environmental Restoration Health Physics Organization of the Westinghouse Hanford Company. The survey methodology was based on utilization of the Ultrasonic Ranging and Data System (USRADS) for automated recording of the gross gamma radiation levels at or near six (6) inches and at three (3) feet from the surface soil

Cleanup Verification Package for the 118-F-2 Burial Ground

International Nuclear Information System (INIS)

Capron, J.M.; Anselm, K.A.

2008-01-01

This cleanup verification package documents completion of remedial action, sampling activities, and compliance with cleanup criteria for the 118-F-2 Burial Ground. This burial ground, formerly called Solid Waste Burial Ground No. 1, was the original solid waste disposal site for the 100-F Area. Eight trenches contained miscellaneous solid waste from the 105-F Reactor and one trench contained solid waste from the biology facilities

618-10 Burial Ground Trench Remediation and 618-10 and 618-11 Burial Ground Nonintrusive Characterization of Vertical Pipe Units Lessons Learned

Energy Technology Data Exchange (ETDEWEB)

Darby, J. W.

2012-06-28

A “lessons learned” is a noteworthy practice or innovative approach that is captured and shared to promote repeat application, or an adverse work practice/experience that is captured and shared to avoid reoccurrence. This document provides the lessons learned identified by the 618-10 Burial Ground trench remediation and the 618-10 and 618-11 Burial Ground nonintrusive characterization of the vertical pipe units (VPUs).

Project TN-030: hydrogeology - ORNL radioactive waste burial grounds

International Nuclear Information System (INIS)

1981-01-01

Continuation of an effort started in 1980, the water-level and precipitation data collected during the early years of the project were compiled into a series of five basic data reports. Technical advice on the design of piezometers in Burial Ground 5 was provided, and their construction has been monitored. Field work has continued, principally in Burial Grounds 5 and 6

Report of conceptual design for TRU solid waste facilities adjacent to 200H Area: Savannah River Plant

International Nuclear Information System (INIS)

1978-02-01

Facilities for consolidating Savannah River Plant solid transuranic (TRU) waste and placing in long-term safe, retrievable storage have been designed conceptually. A venture guidance appraisal of cost for the facilities has been prepared. The proposed site of the new processing area is adjacent to existing H Area facilities. The scopes of work comprising the conceptual design describe facilities for: exhuming high-level TRU waste from buried and pad-stored locations in the plant burial ground; opening, emptying, and sorting waste containers and their contents within shielded, regulated enclosures; volume-reducing the noncombustibles by physical processes and decontaminating the metal waste; burning combustibles; fixing the consolidated waste forms in a concrete matrix within a double-walled steel container; placing product containers in a retrievable surface storage facility adjacent to the existing plant burial ground; and maintaining accountability of all special nuclear materials. Processing, administration, and auxiliary service buildings are to be located adjacent to existing H Area facilities where certain power and waste liquid services will be shared

Initial site characterization and evaluation of radionuclide contaminated soil waste burial grounds

International Nuclear Information System (INIS)

Phillips, S.J.; Reisenauer, A.E.; Rickard, W.H.; Sandness, G.A.

1977-02-01

A survey of historical records and literature containing information on the contents of 300 Area and North Burial Grounds was completed. Existing records of radioactive waste location, type, and quantity within each burial ground facility were obtained and distributed to cooperating investigators. A study was then initiated to evaluate geophysical exploration techniques for mapping buried waste materials, waste containers, and trench boundaries. Results indicate that a combination of ground penetrating radar, magnetometer, metal detector, and acoustic measurements will be effective but will require further study, hardware development, and field testing. Drilling techniques for recovering radionuclide-contaminated materials and sediment cores were developed and tested. Laboratory sediment characterization and fluid transport and monitoring analyses were begun by installation of in situ transducers at the 300 North Burial Ground site. Biological transport mechanisms that control radionuclide movement at contaminated sites were also studied. Flora and fauna presently inhabiting specific burial ground areas were identified and analyzed. Future monitoring of specific mammal populations will permit determination of dose rate and pathways of contaminated materials contained in and adjacent to burial ground sites

Enhanced Site Characterization of the 618-4 Burial Ground

Energy Technology Data Exchange (ETDEWEB)

Murray, Christopher J.; Last, George V.; Chien, Yi-Ju

2001-09-25

This report describes the results obtained from deployment of the Enhanced Site Characterization System (ESCS) at the Hanford Site's 618-4 Burial Ground. The objective of this deployment was to use advanced geostatistical methods to integrate and interpret geophysical and ground truth data, to map the physical types of waste materials present in unexcavated portions of the burial ground. One issue of particularly interest was the number of drums (containing depleted uranium metal shavings or uranium-oxide powder) remaining in the burial ground and still requiring removal.Fuzzy adaptive resonance theory (ART), a neural network classification method, was used to cluster the study area into 3 classes based on their geophysical signatures. Multivariate statistical analyses and discriminant function analysis (DFA) indicated that the drum area as well as a second area (the SW anomaly) had similar geophysical signatures that were different from the rest of the burial ground. Further analysis of the drum area suggested that as many as 770 drums to 850 drums may remain in that area. Similarities between the geophysical signatures of the drum area and the SW anomaly suggested that excavation of the SW anomaly area also proceed with caution.Deployment of the ESCS technology was successful in integrating multiple geophysical variables and grouping these observations into clusters that are relevant for planning further excavation of the buried ground. However, the success of the technology could not be fully evaluated because reliable ground truth data were not available to enable calibration of the different geophysical signatures against actual waste types.

Improvement in operating incident experience at the Savannah River Burial Ground

International Nuclear Information System (INIS)

Cornman, W.R.

1979-01-01

Low-level radioactive wastes generated at the Savannah River Plant and Laboratory are stored at the Savannah River burial ground. These wastes have accumulated from >20 years of reprocessing nuclear fuels and materials for defense programs at the Savannah River Plant. Burial in earthen trenches and aboveground storage for transuranic materials are the principal modes of storage. The infrequent operating incidents that have occurred during the 20-year period have been analyzed. The incidents can be categorized as those causing airborne contamination, waterborne contamination, or vegetation contamination through penetration of plant roots into contaminated soil. Contamination was generally confined to the immediate area of the burial ground. Several incidents occurred because of unintentional burial or exhumation of material. The frequency of operating incidents decreased with operating experience of the burial ground, averaging only about two incidents per year during the last six years of operation

Migration studies at the Savannah River Plant shallow land burial site

International Nuclear Information System (INIS)

Stone, J.A.; Oblath, S.B.; Hawkins, R.H.; Emslie, R.H.; Ryan, J.P. Jr.; King, C.M.

1983-01-01

Radionuclide migration from the Savannah River Plant low-level waste burial ground was studied in ongoing programs that provide generic data on a shallow land burial site in a humid region and support local waste disposal operations. Field, laboratory, and theoretical work continued in four areas. (1) Subsurface Monitoring: Groundwater around the burial ground was monitored for traces of radioactivity and mercury. (2) Lysimeter Tests: Gamma-emitting radionuclides were identified by sensitive methods in defense waste lysimeter percolate waters. Results from these and other lysimeters containing tritium, I-129, or Pu-239 sources are given. (3) Soil-Water Chemistry: Experiments on specific factors affecting migration of Cs-137 showed that potassium significantly increases cesium mobility, thus confirming observations with trench waters. Distribution coefficients for ruthenium were measured. (4) Transport Modeling: Efforts to refine and validate the SRL dose-to-man model continued. Transport calculations were made for tritium, Sr-90, Tc-99, and TRU radionuclides. 12 references, 3 tables

Estimated erosion rate at the SRP burial ground

International Nuclear Information System (INIS)

Horton, J.H.; Wilhite, E.L.

1978-04-01

The rate of soil erosion at the Savannah River Plant (SRP) burial ground can be calculated by means of the universal soil loss equation. Erosion rates estimated by the equation are more suitable for long-term prediction than those which could be measured with a reasonable effort in field studies. The predicted erosion rate at the SRP burial ground ranges from 0.0007 cm/year under stable forest cover to 0.38 cm/year if farmed with cultivated crops. These values correspond to 170,000 and 320 years, respectively, to expose waste buried 4 ft deep

Engineering evaluation of the 618-9 Burial Ground expedited response action

International Nuclear Information System (INIS)

1991-08-01

Throughout Hanford Site history, chemical waste products were disposed via burial in trenches. One such trench was the 618-9 Burial Ground, located in the 600 Area on the Hanford Site. The 618-9 Burial Ground was suspected to contain approximately 5,000 ga (19,000 L) of uranium contaminated solvent in 55-gal (208-L) steel drums. On December 20, 1990, the US Department of Energy (DOE) was instructed by the US Environmental Protection Agency (EPA) and the State of Washington Department of Ecology (Ecology) to initiate planning necessary to implement an expedited response action (ERA) for the 618-9 Burial Ground. The project was to be implemented in two phases: (1) removal of immediate human health and environmental hazards and (2) remediation of contaminated soil. Phase 1 of the project was initiated February 15, 1991. During Phase 1 activities approximately 700 gal (2,650 L) of methyl isobutyl ketone (hexone) and 900 gal (3,400 L) of kerosene solvent were removed from the 618-9 Burial Ground. A significant amount of scrap process equipment/building debris was excavated. The results of an environmental risk assessment for chemicals above detection further determined that risks posed by other detected constituents to human health and the environment are negligible. A compilation of activities utilized for determining subsequent remediation activities for the 618-9 Burial Ground is presented. This includes: (1) Phase 1 activities, (2) sampling performed and associated data results, (3) results of the risk assessment, and (4) applicable or relevant and appropriate requirements. 13 refs., 5 figs., 4 tabs

Decommissioning and decontamination (burial ground stabilization) studies

International Nuclear Information System (INIS)

Cline, J.F.

1980-01-01

The decommissioning and decontamination of retired Hanford facilities and the future use of surrounding landscapes require isolation of contaminated wastes from the biosphere. Burial ground stabilization studies were conducted to determine the effectiveness of physical barriers for isolating contaminated wastes in shallow-land burial sites from plants and animals. This study was undertaken to determine the effectiveness of using a layer of loose rock between the waste and the surface soil covering to prevent both plant root and animal penetrations

Hydrologic transport of radionuclides from low-level waste burial grounds

International Nuclear Information System (INIS)

Duguid, J.O.

1977-01-01

The physical characteristics of the virgin site and of the disturbed site after burial drastically affect the transport of radionuclides from buried waste. The disturbance of the land surface during the waste burial operation causes changes in the local ground-water regimen. These changes can increase the water table elevation and cause the occurrence of perched water in burial trenches. The combination of these changes may lead to submersion of the waste and to increased radionuclide transport from the burial site in both surface and ground water. Factors such as ion exchange can retard or in some cases, with competing ions, can also mobilize radionuclides and increase their discharge into ground and surface water. Because of complexing agents (organics) contained in the waste, increased mobility of some radionuclides can be expected. The chemical form of radionuclides in the water, the ground-water quality, and the chemistry of the geologic formation in which the waste is buried all influence the movement of radionuclides in the hydrologic system. For the assessment of the environmental impact of low-level waste burial, models capable of simulating both the chemical and the physical factors that affect hydrologic transport must be available. Several models for conducting such simulation are presently available. However,the input parameters used in these models are highly variable, and the accuracy of parameter measurement must be considered in evaluating the reliability of simulated results

Low-Level Burial Grounds dangerous waste permit application: Request for exemption from lined trench requirements and from land disposal restrictions for residual liquid at 218-E-12B Burial Ground Trench 94

International Nuclear Information System (INIS)

1992-10-01

This document has been prepared and is being submitted to the respective agencies to satisfy three objectives of the US Department of Energy (DOE) Richland Field Office (DOE-RL) concerning Trench 94 of the 218-E-12B Burial Ground. The 218-E-12B Burial Ground is located in the 200 East Area of the Hanford Facility. Figure 1-1 shows the general location of the Hanford Site. The 218-E-12B Burial Ground is one of eight burial grounds included in the Low-Level Burial Grounds (LLBG), a treatment, storage and/or disposal (TSD) unit. Decommissioned, defueled naval submarine reactor compartments (SRCs) contain radioactivity caused by exposure of structural components to neutrons during normal operation of the submarines. After all the alternatives were evaluated in the US Department of the Navy 1984 environmental impact statement (EIS) (USN 1984), land burial of the SRCs was selected as the preferred disposal option. The SRCs currently are sent to Trench 94 of the 218-E-12B Burial Ground. In addition to radioactivity, the SRCs disposed in. The DOE-RL's three objectives in preparing and submitting this document are as follows. Request from Ecology an exemption from dangerous waste landfill liner and leachate collection and removal system (hereinafter referred to as liner/leachate system) requirements for Trench 94 of the 218-E-12B Burial Ground. Petition Ecology to exempt residual liquid in the SRCs from land disposal restrictions. Obtain EPA Region 10 review and comment on the request to Ecology for exemption from liner/leachate system requirements

Hydrologic transport of radionuclides from low-level waste burial grounds

International Nuclear Information System (INIS)

Duguid, J.O.

1979-01-01

The physical characteristics of the virgin site and of the disturbed site after burial drastically affect the transport of radionuclides from buried waste. The disturbance of the land surface during the waste burial operation causes changes in the local ground-water regimen. These changes can increase the water table elevation and cause the occurrence of perched water in burial trenches. The combination of these changes may lead to submersion of the waste and to increased radionuclide transport from the burial site in both surface and groundwater. Factors such as ion exchange can retard or in some cases, with competing ions, can also mobilize radionuclides and increase their discharge into ground and surface water. Because of complexing agents (organics) contained in the waste, increased mobility of some radionuclides can be expected. The chemical form of radionuclides in the water, the ground-water quality, and the chemistry of the geologic formation in which the waste is buried all influence the movement of radionuclides in the hydrologic system. For the assessment of the environmental impact of low-level waste burial, models capable of simulating both the chemical and the physical factors that affect hydrologic transport must be available. Several models for conducting such simulation are presently available. However, the input parameters used in these models are highly variable; and the accuracy of parameter measurement must be considered in evaluating the reliability of simulated results

Evaluation of Elevated Tritium Levels in Groundwater Downgradient from the 618-11 Burial Ground Phase I Investigations

Energy Technology Data Exchange (ETDEWEB)

Dresel, P.E.; Smith, R.M.; Williams, B.A.; Thompson, C.J.; Evans, J.C.; Hulstrom, L.C.

2000-05-01

This report describes the results of the preliminary investigation of elevated tritium in groundwater discovered near the 618-11 burial ground, located in the eastern part of the Hanford Site. Tritium in one well downgradient of the burial ground was detected at levels up to 8,140,000 pCi/L. The 618-11 burial ground received a variety of radioactive waste from the 300 Area between 1962 and 1967. The burial ground covers 3.5 hectare (8.6 acre) and contains trenches, large diameter caissons, and vertical pipe storage units. The burial ground was stabilized with a native sediment covering. The Energy Northwest reactor complex was constructed immediately east of the burial ground.

Evaluation of Elevated Tritium Levels in Groundwater Downgradient from the 618-11 Burial Ground Phase I Investigations

International Nuclear Information System (INIS)

Dresel, P.E.; Smith, R.M.; Williams, B.A.; Thompson, C.J.; Evans, J.C.; Hulstrom, L.C.

2000-01-01

This report describes the results of the preliminary investigation of elevated tritium in groundwater discovered near the 618-11 burial ground, located in the eastern part of the Hanford Site. Tritium in one well downgradient of the burial ground was detected at levels up to 8,140,000 pCi/L. The 618-11 burial ground received a variety of radioactive waste from the 300 Area between 1962 and 1967. The burial ground covers 3.5 hectare (8.6 acre) and contains trenches, large diameter caissons, and vertical pipe storage units. The burial ground was stabilized with a native sediment covering. The Energy Northwest reactor complex was constructed immediately east of the burial ground

Waste migration studies at the Savannah River Plant burial ground

International Nuclear Information System (INIS)

Stone, J.A.; Oblath, S.B.; Hawkins, R.H.; Grant, M.W.; Hoeffner, S.L.; King, C.M.

1985-01-01

The low-level radioactive waste burial ground at the Savannah River Plant is a typical shallow-land-burial disposal site in a humid region. Studies of waste migration at this site provide generic data for designing other disposal facilities. A program of field, laboratory, and modeling studies for the SRP burial ground has been conducted for several years. Recent results of lysimeter tests, soil-water chemistry studies, and transport modeling are reported. The lysimeter experiments include ongoing tests with 40 lysimeters containing a variety of defense wastes, and recently concluded lysimeter tests with tritium and plutonium waste forms. The tritium lysimeter operated 12 years. In chemistry studies, measurements of soil-water distribution coefficients (K/sub d/) were concluded. Current emphasis is on identification of trace organic compounds in groundwater from the burial site. Development of the dose-to-man model was completed, and the computer code is available for routine use. 16 refs., 2 figs., 2 tabs

SRS Burial Ground Complex: Remediation in Progress

International Nuclear Information System (INIS)

Griffin, M.; Crapse, B.; Cowan, S.

1998-01-01

Closure of the various areas in the Burial Ground Complex (BGC) represents a major step in the reduction of risk at the Savannah River Site (SRS) and a significant investment of resources. The Burial Ground Complex occupies approximately 195 acres in the central section of the SRS. Approximately 160 acres of the BGC consists of hazardous and radioactive waste disposal sites that require remediation. Of these source acres, one-third have been remediated while two-thirds are undergoing interim or final action. These restoration activities have been carried out in a safe and cost effective manner while minimizing impact to operating facilities. Successful completion of these activities is in large part due to the teamwork demonstrated by the Department of Energy, contractor/subcontractor personnel, and the regulatory agencies. The experience and knowledge gained from the closure of these large disposal facilities can be used to expedite closure of similar facilities

Riding Horse Harness (Based on Materials from the Chulkovo Burial Ground

Directory of Open Access Journals (Sweden)

Grishakov Valeriy V.

2013-12-01

Full Text Available The items of riding horse harness (bits with psalia, stirrups, buckles, decorations of bridles are analyzed in the article on the basis of the materials from the Chulkovo (Murom burial ground site of the 8th-10th centuries, located on right bank of the Oka river. It has been established that the use of horse harness items by the Muroma culture population, which had left the Chulkovo burial ground, is in full correspondence with the general traditions of the Finno-Ugric peoples of the Volga river region characteristic of the 8th-10th centuries. The shapes of the bits correspond to both the steppe (bits with S-shaped and straight psalia and the local traditions (bits with two and three moving rings. A tendency to uniformity is observed in the tradition of stirrups production. The main differences of the Muroma burial grounds from the neighboring Mordovian ones consist in the presence of horse burials (not known among the Mordovians, and, on the other hand, in a practically complete lack of horse harness in the funeral set of human burials. It can be assumed that the importance of cavalry with the Muromа was lower than with the Mordovians who were living next to the steppe world.

Cleanup Verification Package for the 118-B-1, 105-B Solid Waste Burial Ground

International Nuclear Information System (INIS)

Capron, J.M.

2008-01-01

This cleanup verification package documents completion of remedial action, sampling activities, and compliance criteria for the 118-B-1, 105-B Solid Waste Burial Ground. This waste site was the primary burial ground for general wastes from the operation of the 105-B Reactor and P-10 Tritium Separation Project and also received waste from the 105-N Reactor. The burial ground received reactor hardware, process piping and tubing, fuel spacers, glassware, electrical components, tritium process wastes, soft wastes and other miscellaneous debris

Shallow ground burial of low-level waste

International Nuclear Information System (INIS)

Camilleri, A.; Cooper, M.B.; Hargrave, N.J.; Munslow-Davies, L.

1989-01-01

Acceptance criteria for the disposal of low-level radioactive wastes are presented for adoption throughout Australia, a continent in which there are readily available areas in arid, sparsely inhabited places, likely to be suitable as sites for shallow ground burial. Drawing upon overseas practices and experiences, criteria have been developed for low-level waste disposal and are intended to be applicable and relevant to the Australian situation. Concentration levels have been derived for a shallow ground burial facility assuming a realistic institutional control period of 200 years. A comparison is made between this period and institutional control for 100 years and 300 years. Longer institutional control periods enable the acceptance of higher concentrations of radionuclides of intermediate half-lives. Scenarios, which have been considered, include current Australian pastoral practices and traditional Aboriginal occupancy. The derived radionuclide concentration levels for the disposal of low level wastes are not dissimilar to those developed in other countries. 17 refs., 6 tabs., 1 fig

MANAGEMENT OF TRANSURANIC (TRU) WASTE RETRIEVAL PROJECT RISKS SUCCESSES IN THE STARTUP OF THE HANFORD 200 AREA TRU WASTE RETRIEVAL PROJECT

International Nuclear Information System (INIS)

GREENWLL, R.D.

2005-01-01

A risk identification and mitigation method applied to the Transuranic (TRU) Waste Retrieval Project performed at the Hanford 200 Area burial grounds is described. Retrieval operations are analyzed using process flow diagramming. and the anticipated project contingencies are included in the Authorization Basis and operational plans. Examples of uncertainties assessed include degraded container integrity, bulged drums, unknown containers, and releases to the environment. Identification and mitigation of project risks contributed to the safe retrieval of over 1700 cubic meters of waste without significant work stoppage and below the targeted cost per cubic meter retrieved. This paper will be of interest to managers, project engineers, regulators, and others who are responsible for successful performance of waste retrieval and other projects with high safety and performance risks

Closure Plan for Active Low Level Burial Grounds

Energy Technology Data Exchange (ETDEWEB)

SKELLY, W.A.

2000-11-16

This plan has been prepared in response to direction from the U.S. Department of Energy. The purpose of the plan is to define approaches that will be implemented to ensure protection of the public and the environment when active Low-Level Burial Grounds (LLBGs) at the Hanford Site are closed. Performance assessments for active burial grounds in the 200 East and West 200 Areas provide current estimates of potential environmental contamination and doses to the ''maximum exposed individual'' from burial ground operation and closure and compare dose estimates to performance objective dose limits for the facilities. This is an Operational Closure Plan. The intent of the guidance in DOE Order 435.1 is that this plan will be a living document, like the facility performance assessments, and will be revised periodically through the operational life of the LLBGs to reflect updated information on waste inventory. management practices, facility transition planning, schedule dates, assessments of post-closure performance, and environmental consequences. Out year dates identified in this plan are tentative. A Final Closure Plan will be prepared in the future when the timing and extent of closure-related activities for LLBGs can be established with greater certainty. After current operations at the LLBGs are concluded, this plan proposes transitioning of these facilities to the Environmental Restoration Program. This action will enable the Environmental Restoration Program to design and implement consistent and coordinated final remedial actions for active and inactive LLBGs. Active and inactive burial grounds in the 200 West and 200 East Areas are commingled. This plan describes approaches that will be implemented during Interim Closure, Final Closure, and Institutional Control Periods to prepare LLBGs for surface barriers, and the construction of barriers, as well as the scope of inspection, monitoring and maintenance practices that will be performed during

Hydrogeology of the 200 Areas low-level burial grounds

International Nuclear Information System (INIS)

Last, G.V.; Bjornstad, B.N.; Bergeron, M.P.

1989-01-01

This report presents information derived from the installation of 35 ground-water monitoring wells around six low-level radioactive/hazardous waste burial grounds located in the 200 Areas of the Hanford Site in southeastern Washington State. This information was collected between May 20, 1987 and August 1, 1988. The contents of this report have been divided into two volumes. This volume contains the main text. Volume 2 contains the appendixes, including data and supporting information that verify content and results found in the main text. This report documents information collected by the Pacific Northwest Laboratory at the request of Westinghouse Hanford Company. Presented in this report are the preliminary interpretations of the hydrogeologic environment of six low-level burial grounds, which comprise four waste management areas (WMAs) located in the 200 Areas of the Hanford Site. This information and its accompanying interpretations were derived from sampling and testing activities associated with the construction of 35 ground-water monitoring wells as well as a multitude of previously existing boreholes. The new monitoring wells were installed as part of a ground-water monitoring program initiated in 1986. This ground-water monitoring program is based on requirements for interim status facilities in compliance with the Resource Conservation and Recovery Act (1976)

Technology, Safety and Costs of Decommissioning a Reference Low-Level Waste Burial Ground. Appendices

International Nuclear Information System (INIS)

None

1980-01-01

Safety and cost information are developed for the conceptual decommissioning of commercial low-level waste (LLW) burial grounds. Two generic burial grounds, one located on an arid western site and the other located on a humid eastern site, are used as reference facilities for the study. The two burial grounds are assumed to have the same site capacity for waste, the same radioactive waste inventory, and similar trench characteristics and operating procedures. The climate, geology. and hydrology of the two sites are chosen to be typical of real western and eastern sites. Volume 2 (Appendices) contains the detailed analyses and data needed to support the results given in Volume 1.

Chemical speciation of plutonium in the radioactive waste burial ground at the Savannah River Plant

International Nuclear Information System (INIS)

Wilhite, E.L.

1978-08-01

The plutonium chemical species in two types of samples from the Savannah River Plant burial ground for radioactive waste were identified. Samples analyzed were water and sediment from burial ground monitoring well C-17 and soil from an alpha waste burial trench. Soluble plutonium in the monitoring well was less than 12A in diameter, was cationic, and contained about 43% Pu(VI) and 25% Pu(IV). The equilibrium distribution coefficient (K /sub d/) for soluble plutonium from the well water (pH 7) to burial ground soil was about 60. Soil plutonium from the waste trench was not cation-exchanged; 78% of the soil plutonium was associated with metallic oxides in the soil. Approximately 9% of the Pu was contained in the crystalline soil matrix. Thus, about 87% of the plutonium in the soil was in a relatively immobile form. Ion-exchangeable and organic acid forms of plutonium amounted to only about 2.5% each. The bulk of the plutonium now on burial ground soils will be immobile except for movement of soil particles containing plutonium. 6 tables

Low-Level Burial Grounds Dangerous Waste Permit Application

International Nuclear Information System (INIS)

1989-01-01

The single dangerous waste permit identification number issued to the Hanford Site by the US Environmental Protection Agency and the Washington State Department of Ecology is US Environmental Protection Agency/State Identification Number WA 7890008967. This identification number encompasses a number of waste management units within the Hanford Site. Westinghouse Hanford Company is a major contractor to the US Department of Energy-Richland Operations Office and serves as co-operator of the Low-Level Burial Grounds, the waste management unit addressed by this permit application. The Low-Level Burial Grounds Dangerous Waste Permit Application consists of both a Part A and a Part B Permit Application. The original Part A, submitted in November 1985, identified landfills, retrievable storage units, and reserved areas. An explanation of subsequent Part A revisions is provided at the beginning of the Part A section. Part B consists of 15 chapters addressing the organization and content of the Part B checklist prepared by the Washington State Department of Ecology

Comparative assessment of disposal of TRU waste in a greater-confinement disposal facility

International Nuclear Information System (INIS)

Cohn, J.J.; Smith, C.F.; Ciminesi, F.J.; Dickman, P.T.; O'Neal, D.A.

1982-11-01

This study reviewed previous work that established generic limits for shallow land burial of TRU contaminated wastes and extended previous methodology to estimate approximate appropriate burial limits for TRU wastes in an arid zone greater confinement disposal facility (GCDF). An erosion scenario provided the limiting pathway in the previous determination of generic shallow land burial limits. Erosion removed the cover soil, exposing the waste mass to habitation and agriculture. For the deep burial concept (that is, burial at a depth greater than 10 m [33 ft]), the aquifer transport scenario was controlling. In both cases, the assumed site conditions were characteristic of a humid zone in which groundwater flows immediately below the waste deposit. In deriving limits for an arid site GCDF, either the erosion/reclaimer or the aquifer transport scenario could provide the controlling pathway, depending on the nuclide and the assumed burial depth. The derived limits were higher for the arid sited GCDF than those of the generic humid study. The physical processes that increase limits relative to the generic study include increased time during which radioactive decay occurs prior to release and increased dilution. Some nuclides were effectively unlimited in an arid zone GCDF, while others (notably Pu-239) were affected on a much smaller scale, primarily due to very long half-lives. As a final comment, the limit values derived in this report represent adjustments to the calculations of the Healy and Rodgers report (LA-UR-79-100). Those original calculations were very conservative, utilizing a worst case approach, but nevertheless involving significant levels of uncertainty in key assumptions. Consequently, the results are assumption dependent. Other approaches to such an analysis could, and should be used to develop site specific concentration limits for TRU wastes

Ancient tombs in China and shallow ground burial of solid low-intermediate level radioactive wastes

International Nuclear Information System (INIS)

Huang Yawen; Gu Cunli

1987-01-01

Having reviewed the experiences with ancient tombs in China, particularly the experiences with tomb siting, configuration of tombs, backfilling materials, civil engineering techniques, sealing techniques, drainage system, antiseptic techniques, a comparison between the ancient tombs and the shallow ground burial of solid radioactive wastes is made. The authors believe that the brilliant achievements of ancient tombs in China in keeping ancient corpses and funeral objects are a historical evidence for safety of shallow ground burial of radioactive wastes, and that the main experiences with the ancient tombs may be useful to shallow ground burial of solid radioactive wastes

Cleanup Verification Package for the 118-C-1, 105-C Solid Waste Burial Ground

Energy Technology Data Exchange (ETDEWEB)

M. J. Appel and J. M. Capron

2007-07-25

This cleanup verification package documents completion of remedial action for the 118-C-1, 105-C Solid Waste Burial Ground. This waste site was the primary burial ground for general wastes from the operation of the 105-C Reactor and received process tubes, aluminum fuel spacers, control rods, reactor hardware, spent nuclear fuel and soft wastes.

Cleanup Verification Package for the 118-C-1, 105-C Solid Waste Burial Ground

International Nuclear Information System (INIS)

Appel, M.J.; Capron, J.M.

2007-01-01

This cleanup verification package documents completion of remedial action for the 118-C-1, 105-C Solid Waste Burial Ground. This waste site was the primary burial ground for general wastes from the operation of the 105-C Reactor and received process tubes, aluminum fuel spacers, control rods, reactor hardware, spent nuclear fuel and soft wastes

Burial of a Man-At-Arms in Kudash I Burial Ground

Directory of Open Access Journals (Sweden)

Kazantseva Olga A.

2017-07-01

Full Text Available The article features a comprehensive analysis of items discovered in male burial 160 of Kudash I burial ground – a unique source of materials for the research of interactions between the local and foreign population on the Middle Kama region in 3rd – 5th centuries A.D. The monument is located in Bardymsky district of Perm Krai. The complex of metal objects comprises a set of personal protective armament rarely discovered in the Kama region: an open-work helmet, a set of plate armour, a sword, a spear head, a knife and "crooked scythes". The article contains a description of the grave, its structure, morphology and classification of findings, as well as the results of an investigation of the manufacturing technology of the following armament and implements: sword, spear head, knife, and "crooked scythe" conducted using the metallographic method. It also features a graphical reconstruction of the warriors’s protective armament – the helmet. The authors determined counterparts of the grave complex discovered at archaeological sites in the Middle Kama region and the Altai Mountains. The apparel of the man-at-arms represents a unique set of protective and offensive armament. The armour of the deceased is complemented by an open-work ceremonial helmet with an aventail, which suggests that the grave belonged to a military commander. The date of burial was determined on the basis of artefact study results as late 4th – early 5th centuries A.D.

Technology, Safety and Costs of Decommissioning a Reference Low-Level Waste Burial Ground. Main Report

International Nuclear Information System (INIS)

Murphy, E. S.; Holter, G. M.

1980-01-01

Safety and cost information are developed for the conceptual decommissioning of commercial low-level waste (LLW) burial grounds. Two generic burial grounds, one located on an arid western site and the other located on a humid eastern site, are used as reference facilities for the study. The two burial grounds are assumed to have the same site capacity for waste, the same radioactive waste inventory, and similar trench characteristics and operating procedures. The climate, geology. and hydrology of the two sites are chosen to be typical of real western and eastern sites. Volume 1 (Main Report) contains background information and study results in summary form.

Technology, Safety and Costs of Decommissioning a Reference Low-Level Waste Burial Ground. Main Report

Energy Technology Data Exchange (ETDEWEB)

Murphy, E. S.; Holter, G. M.

1980-06-01

Safety and cost information are developed for the conceptual decommissioning of commercial low-level waste (LLW) burial grounds. Two generic burial grounds, one located on an arid western site and the other located on a humid eastern site, are used as reference facilities for the study. The two burial grounds are assumed to have the same site capacity for waste, the same radioactive waste inventory, and similar trench characteristics and operating procedures. The climate, geology. and hydrology of the two sites are chosen to be typical of real western and eastern sites. Volume 1 (Main Report) contains background information and study results in summary form.

Low-level burial grounds dangerous waste permit application design documents

International Nuclear Information System (INIS)

1990-08-01

This document serves a supplement to the already existing ''Low-Level Burial Ground Dangerous Waste Permit Application Design Documents.'' This paper contains information regarding drawings, construction specifications, and liner/leachate compatibility test plans

Technical data summary: Plan for closure of the 643-G burial ground

International Nuclear Information System (INIS)

Cook, J.R.

1987-01-01

This report involves the actions of closing the 643-G burial ground which involves waste removal, stabilization, and capping. Remedial action involves the removing of the transuranic waste and closing of the grid wells. The closure cap for the burial site will consist of native soil, clay, and gravel. This will assure long-term physical and chemical stability. (MB)

Evaluation of burial ground soil covers

International Nuclear Information System (INIS)

Fenimore, J.W.

1976-11-01

Solid radioactive waste burial at the Savannah River Plant between 1955 and 1972 filled a 76-acre site. Burial operations then were shifted to an adjacent site, and a program was begun to develop a land cover that would: (1) minimize soil erosion; and (2) protect the buried waste from deep-rooted plants, since radionuclides can be recycled by uptake through root systems. In anticipation of the need for a suitable soil cover, five grass species were planted on 20 plots (4 plots of each species) at the burial ground (Facility 643-G) in 1969. The grass plots were planted for evaluation of viability, root depth, and erosion protection existing under conditions of low fertility and minimum care. In addition, 16 different artificial soil covers were installed on 32 plots (each cover on two plots) to evaluate: (1) resistance of cover to deterioration from weathering; (2) resistance of cover to encroachment by deep-rooted plants; and (3) soil erosion protection provided by the cover. All test plots were observed and photographed in 1970 and in 1974. After both grass and artificial soil covers were tested five years, the following results were observed: Pensacola Bahia grass was the best of the five cover grasses tested; and fifteen of the sixteen artificial covers that were tested controlled vegetation growth and soil erosion. Photographs of the test plots will be retaken at five-year intervals for future documentation

Performance Assessment Monitoring Plan for the Hanford Site Low-Level Burial Grounds

International Nuclear Information System (INIS)

2006-01-01

The U.S. Department of Energy Order 435.1, Radioactive Waste Management, requires a disposal authorization statement authorizing operation (or continued operation) for low-level waste disposal facilities. In fulfillment of these requirements, a disposal authorization statement was issued on October 25, 1999, authorizing the Hanford Site to transfer, receive, possess, and dispose of low-level radioactive waste at the 200 East Area burial grounds and the 200 West Area burial grounds. One of the conditions is that monitoring plans for the 200 East Area and 200 West Area low-level burial grounds be written and approved by the Richland Operations Office. As a result of a record of decision for the Hanford Site Solid Waste Program and acceptance of the Hanford Site Solid Waste Environmental Impact Statement, the use of the low-level burial ground (LLBG) as a disposal facility for low-level and mixed low-level wastes has been restricted to lined trenches and the Navy reactor-compartment trench only. Hence, as of July 2004, only the two lined trenches in burial ground 218-W-5 (trenches 31 and 34, see Appendix A) and the Navy reactor-compartment trench in burial ground 218 E 12B (trench 94) are allowed to receive waste. When the two lined trenches are filled, the LLBG will cease to operate except for reactor compartment disposal at trench 94. Remaining operational lifetime of the LLBG is dependent on waste volume disposal rates. Existing programs for air sampling and analyses and subsidence monitoring are currently adequate for performance assessment at the LLBG. The waste disposal authorization for the Hanford Site is based (in part) on the post-closure performance assessments for the LLBG. In order to maintain a useful link between operational monitoring (e.g., Resource Conservation and Recovery Act [RCRA], Comprehensive Environmental Response, Compensation, and Liability Act, and State Waste Discharge Permits), constituents, monitoring frequencies, and boundaries require

Waste analysis plan for the low-level burial grounds

International Nuclear Information System (INIS)

Barnes, B.M.

1996-01-01

This waste analysis plan (WAP) has been prepared for the Low-Level Burial Grounds that are located in the 200 East and 200 West Areas of the Hanford Facility, Richland, Washington. This WAP documents the methods used to characterize and obtain and analyze representative samples of waste managed at this unit

Waste analysis plan for the low-level burial grounds

Energy Technology Data Exchange (ETDEWEB)

Haas, C.R.

1996-09-19

This waste analysis plan (WAP) has been prepared for the Low-Level Burial Grounds (LLBG) which are located in the 200 East and West Areas of the Hanford Facility, Richland, Washington. This WAP documents the methods used to characterize, and obtain and analyze representative samples of waste managed at this unit.

Solid waste retrieval. Phase 1, Operational basis

International Nuclear Information System (INIS)

Johnson, D.M.

1994-01-01

This Document describes the operational requirements, procedures, and options for execution of the retrieval of the waste containers placed in buried storage in Burial Ground 218W-4C, Trench 04 as TRU waste or suspect TRU waste under the activity levels defining this waste in effect at the time of placement. Trench 04 in Burial Ground 218W-4C is totally dedicated to storage of retrievable TRU waste containers or retrievable suspect TRU waste containers and has not been used for any other purpose

Solid waste retrieval. Phase 1, Operational basis

Energy Technology Data Exchange (ETDEWEB)

Johnson, D.M.

1994-09-30

This Document describes the operational requirements, procedures, and options for execution of the retrieval of the waste containers placed in buried storage in Burial Ground 218W-4C, Trench 04 as TRU waste or suspect TRU waste under the activity levels defining this waste in effect at the time of placement. Trench 04 in Burial Ground 218W-4C is totally dedicated to storage of retrievable TRU waste containers or retrievable suspect TRU waste containers and has not been used for any other purpose.

Hydrology of the solid waste burial ground as related to potential migration of radionuclides, Idaho National Engineering Laboratory

Science.gov (United States)

Barraclough, Jack T.; Robertson, J.B.; Janzer, V.J.; Saindon, L.G.

1976-01-01

A study was made (1970-1974) to evaluate the geohydrologic and geochemical controls on subsurface migration of radionuclides from pits and trenches in the Idaho National Engineering Laboratory (INEL) solid waste burial ground and to determine the existence and extent of radionuclide migration from the burial ground. A total of about 1,700 sediment, rock, and water samples were collected from 10 observation wells drilled in and near the burial ground of Idaho National Engineering Laboratory, formerly the National Reactor Testing Station (NRTS). Within the burial ground area, the subsurface rocks are composed principally of basalt. Wind- and water-deposited sediments occur at the surface and in beds between the thicker basalt zones. Two principal sediment beds occur at about 110 feet and 240 feet below the land surface. The average thickness of the surficial sedimentary layer is about 15 feet while that of the two principal subsurface layers is 13 and 14 feet, respectively. The water table in the aquifer beneath the burial ground is at a depth of about 580 feet. Fission, activation, and transuranic elements were detected in some of the samples from the 110- and 240-foot sedimentary layers. (Woodard-USGS)

Hydrogeology of the 200 Areas low-level burial grounds

International Nuclear Information System (INIS)

Last, G.V.; Bjornstad, B.N.; Bergeron, M.P.

1989-01-01

This report presents information derived form the installation of 35 ground-water monitoring wells around six low-level radioactive/hazardous waste burial grounds located in the 200 Areas of the Hanford Site in southeastern Washington State. This information was collected between May 20, 1987 and August 1, 1988. The contents of this report have been divided into two volumes. Volume 1 contains the main text. This Volume contains the appendixes, including data and supporting information that verify content and results found in the main text

Characterization of the Hanford 300 area burial grounds. Decontamination and decommissioning regulatory issues

International Nuclear Information System (INIS)

Morris, F.A.; Smith, R.F.; Phillips, S.J.

1979-03-01

The Hanford 300 Area Burial Grounds characterization project has identified four management alternatives for disposition of the burial grounds. These alternatives are: (1) abandonment, (2) entombment, (3) perpetual care, and (4) exhumation and translocation. Major Federal statutes and regulations that could apply to management alternatives are identified along with the constraints that applicable laws could impose. This analysis includes explicit attention to the uncertainty surrounding various legal constraints. Also specified are legislative developments as well as trends in other agencies and the courts, obtained by review of legislative proceedings, statutes and regulations, that could result in legislation or policies posing additional constraints

Applicability of a generic monitoring program for radioactive waste burial grounds at Oak Ridge National Laboratory and Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

1978-07-01

Six burial grounds were evaluated at Oak Ridge to determine which would be most suitable for testing the generic monitoring approach, and two were selected. Burial Ground 4 was chosen because it is known to be leaking radioactivity and a monitoring program is desirable to determine the source, pattern and extent of the leakage. Burial Ground 6 was chosen because the most complete radiologic and geologic data is available and modern burial practices have been utilized at this site. At the Idaho National Engineering Laboratory (INEL) only one burial ground exists, the Radioactive Waste Management Complex (RWMC). The data available on the burial grounds are insufficient for an adequate understanding of radionuclide migration patterns and accordingly, inadequate for the design of reliable monitoring programs. It was decided, therefore, that preliminary monitoring programs should be designed in order to obtain additional data for a later implementation of reliable monitoring programs. The monitoring programs designed for ORNL consist primarily of the installation of surface water monitoring stations, the surveillance of trench sump wells, a test boring program to study subsurface geologic conditions, a ground water sampling program and the installation of instrumentation, specifically infiltrometers and evaporation pans, to develop data on site water balances. The program designed for the INEL burial ground includes installation of trench sumps, a ground water monitoring program, test borings to further define subsurface geohydrologic conditions and the installation of instrumentation to develop data on the site water balance. The estimated costs of implementing the recommended programs are about $420,820 for monitoring Burial Grounds 4 and 6 at Oak Ridge and $382,060 for monitoring the RWMC at INEL. 12 figures

Solid Waste Burial Grounds/Central Waste Complex hazards assessment

International Nuclear Information System (INIS)

Broz, R.E.

1994-01-01

This document establishes the technical basis in support of Emergency Planning Activities for Solid Waste Burial Grounds/Central Waste Complex on the Hanford Site. The document represents an acceptable interpretation of the implementing guidance document for DOE Order 5500.3A. Through this document, the technical basis for the development of facility specific Emergency Action Levels and the Emergency Planning Zone is documented

The Remediation of Hanford's Last Low-Level Waste Burial Grounds in the 300 Area: 618-7 and 618-1

International Nuclear Information System (INIS)

Haass, M.J.

2009-01-01

Under the U.S. Department of Energy's (DOE) River Corridor Closure Project, Washington Closure Hanford (WCH) has completed remediation of more than seven low-level waste (LLW) burial grounds in the 300 Area of the Hanford Site. The records of decision for the burial grounds required excavation, characterization, and transport of contaminated material to a Resource Conservation and Recovery Act of 1976-compliant hazardous waste landfill. This paper discusses the challenges and lessons learned from remediating the last two major burial grounds in the 300 Area: 618-7 and 618-1. The 618-7 Burial Ground was in operation from 1960 through 1973, during which it received waste from the production of Zircaloy (zirconium alloy) jacketed metallic uranium fuel rods and thoria targets for the production of uranium-233. Its major remediation challenges included the recovery, characterization, and disposal of 550 drums and disposal of two compressed gas cylinders that were suspected to contain highly toxic chemicals. Approximately 100 of the drums contained Zircaloy metal turnings that could be pyrophoric under certain conditions. Remediation activities were completed in December 2008. The 618-1 Burial Ground was in operation from 1945 (i.e., the beginning of Hanford operations) through 1951. It received waste from 300 Area laboratories that conducted experimental work associated with World War II and Cold War era processes for fuel fabrication and the production of plutonium. Some of the wastes were associated with highly radioactive irradiated material. Remediation of this burial ground is still in progress and is expected to be completed by June 2009. Information presented in this paper will be an aid to those involved in the planning, design, and remediation of burial grounds located on the DOE complex. (authors) Remediation of the 618-7 Burial Ground was completed in December 2008; the 618-1 Burial Ground is proceeding without incident and is expected to be completed in June

Final Hazard Categorization for the Remediation of Six 300-FF-2 Operable Unit Solid Waste Burial Grounds

International Nuclear Information System (INIS)

Ludowise, J.D.

2006-01-01

This report provides the final hazard categorization (FHC) for the remediation of six solid waste disposal sites (referred to as burial grounds) located in the 300-FF-2 Operable Unit (OU) on the Hanford Site. These six sites (618-1, 618-2, 618-3, 618-7, 618-8, and 618-13 Burial Grounds) were determined to have a total radionuclide inventory (WCH 2005a, WCH 2005d, WCH 2005e and WCH 2006b) that exceeds the DOE-STD-1027 Category 3 threshold quantity (DOE 1997) and are the subject of this analysis. This FHC document examines the hazards, identifies appropriate controls to manage the hazards, and documents the FHC and commitments for the 300-FF-2 Burial Grounds Remediation Project

Final Hazard Categorization for the Remediation of Six 300-FF-2 Operable Unit Solid Waste Burial Grounds

Energy Technology Data Exchange (ETDEWEB)

J. D. Ludowise

2006-12-12

This report provides the final hazard categorization (FHC) for the remediation of six solid waste disposal sites (referred to as burial grounds) located in the 300-FF-2 Operable Unit (OU) on the Hanford Site. These six sites (618-1, 618-2, 618-3, 618-7, 618-8, and 618-13 Burial Grounds) were determined to have a total radionuclide inventory (WCH 2005a, WCH 2005d, WCH 2005e and WCH 2006b) that exceeds the DOE-STD-1027 Category 3 threshold quantity (DOE 1997) and are the subject of this analysis. This FHC document examines the hazards, identifies appropriate controls to manage the hazards, and documents the FHC and commitments for the 300-FF-2 Burial Grounds Remediation Project.

Geophysical Investigation of the 618-10 and 618-11 Burial Grounds, 300-FF-2 Operable Unit

International Nuclear Information System (INIS)

Bergstrom, K.A.; Bolin, D.J.; Mitchell, T.H.

1997-09-01

This document summarizes the results of geophysical investigations conducted at two radioactive solid waste burial grounds, 618-10 and 618-11. The burial grounds are located approximately 4.5 miles and 7 miles north of the 300 Area, respectively. These sites are within the 300-FF-2 Operable Unit, where geophysical techniques are being used to characterize the distribution of solid waste in the subsurface as part of the Limited Field Investigations for this operable unit

The new Japanese policy for TRU-waste management

International Nuclear Information System (INIS)

Yamamoto, M.

1992-01-01

In July 1991, the Advisory Committee on Radioactive Waste of the Japan Atomic Energy Commission announced its report on a new Japanese policy for TRU-waste management. The total volume of radioactive wastes which contain TRU nuclides has reached the equivalent of about 40,000,200-liter drums, and is expected to grow to about 300,000 drums by the year 2010. Further development is required to reduce the volume of the existing waste and to decrease the amount of waste being generated. Wastes with concentration levels exceeding a threshold limit of 1 Giga-Becquerel per ton will be disposed in an underground facility. Those wastes with lower activities will be sent to a shallow-land burial facility. The goal of research and development is the completion of the disposal system by the late 1990's. (author)

Cleanup Verification Package for the 118-F-6 Burial Ground

International Nuclear Information System (INIS)

Sulloway, H.M.

2008-01-01

This cleanup verification package documents completion of remedial action for the 118-F-6 Burial Ground located in the 100-FR-2 Operable Unit of the 100-F Area on the Hanford Site. The trenches received waste from the 100-F Experimental Animal Farm, including animal manure, animal carcasses, laboratory waste, plastic, cardboard, metal, and concrete debris as well as a railroad tank car

Treatment of Bottled Liquid Waste During Remediation of the Hanford 618-10 Burial Ground - 13001

International Nuclear Information System (INIS)

Faulk, Darrin E.; Pearson, Chris M.; Vedder, Barry L.; Martin, David W.

2013-01-01

A problematic waste form encountered during remediation of the Hanford Site 618-10 burial ground consists of bottled aqueous waste potentially contaminated with regulated metals. The liquid waste requires stabilization prior to landfill disposal. Prior remediation activities at other Hanford burial grounds resulted in a standard process for sampling and analyzing liquid waste using manual methods. Due to the highly dispersible characteristics of alpha contamination, and the potential for shock sensitive chemicals, a different method for bottle processing was needed for the 618-10 burial ground. Discussions with the United States Department of Energy (DOE) and United States Environmental Protection Agency (EPA) led to development of a modified approach. The modified approach involves treatment of liquid waste in bottles, up to one gallon per bottle, in a tray or box within the excavation of the remediation site. Bottles are placed in the box, covered with soil and fixative, crushed, and mixed with a Portland cement grout. The potential hazards of the liquid waste preclude sampling prior to treatment. Post treatment verification sampling is performed to demonstrate compliance with land disposal restrictions and disposal facility acceptance criteria. (authors)

Treatment of Bottled Liquid Waste During Remediation of the Hanford 618-10 Burial Ground - 13001

Energy Technology Data Exchange (ETDEWEB)

Faulk, Darrin E.; Pearson, Chris M.; Vedder, Barry L.; Martin, David W. [Washington Closure Hanford, LLC, Richland, WA 99354 (United States)

2013-07-01

A problematic waste form encountered during remediation of the Hanford Site 618-10 burial ground consists of bottled aqueous waste potentially contaminated with regulated metals. The liquid waste requires stabilization prior to landfill disposal. Prior remediation activities at other Hanford burial grounds resulted in a standard process for sampling and analyzing liquid waste using manual methods. Due to the highly dispersible characteristics of alpha contamination, and the potential for shock sensitive chemicals, a different method for bottle processing was needed for the 618-10 burial ground. Discussions with the United States Department of Energy (DOE) and United States Environmental Protection Agency (EPA) led to development of a modified approach. The modified approach involves treatment of liquid waste in bottles, up to one gallon per bottle, in a tray or box within the excavation of the remediation site. Bottles are placed in the box, covered with soil and fixative, crushed, and mixed with a Portland cement grout. The potential hazards of the liquid waste preclude sampling prior to treatment. Post treatment verification sampling is performed to demonstrate compliance with land disposal restrictions and disposal facility acceptance criteria. (authors)

Beads of the Birsk Burial Ground in the Context of the Antiquities of the Early Middle Ages

Directory of Open Access Journals (Sweden)

Ruslanova Rida Raisovna

2016-04-01

Full Text Available Early Middle Ages in the Southern Urals is the time of the tumultuous ethnocultural processes, that is an echo of the era of the Great Migration. At this time, the bakhmutinskaya culture was formed (3rd-8th centuries A.D.. The Birsk burial ground is one of the unique monuments of this period – it appeared in the second third of the 1st millennium B.C. The Birsk burial ground is a fiducial monument for studying history, ethno-cultural, migration and trade processes occurring in the Southern Urals, and the content in the composition of grave goods makes it supplies an important source in the study of early medieval history of East European forest. A variety of types of beads from the Birsk burial ground allows suggesting that the necropolis was one of the major points on the caravan trade and exchange path. According to it, the exchange could take place on imports of products (furs, honey, metals. The article describes a set of beads from the Birsk burials – evidence of a monument in the system of early medieval antiquities (3rd-8th centuries A.D.. The complex morpho-technological research dealt with 218 complexes containing 6705 instances of beads and jewelry. The feature of the monument is the presence of necklaces jewelry from all the selected materials along with the material. The Birsk burial ground demonstrates various forms of products, colors used glass for monochrome and polychrome decorations. The presented work can be used in the study of material culture and trade exchange operations of the medieval population of the Urals.

Hanford facility dangerous waste permit application, low-level burial grounds

International Nuclear Information System (INIS)

Engelmann, R.H.

1997-01-01

The Hanford Facility Dangerous Plaste Permit Application is considered to be a single application organized into a General Information Portion (document number DOE/RL-91-28) and a Unit-Specific Portion. The scope of the Unit-Specific Portion is limited to Part B permit application documentation submitted for individual, 'operating' treatment, storage, and/or disposal units, such as the Low-Level Burial Grounds (this document, DOE/RL-88-20)

Hanford facility dangerous waste permit application, low-level burial grounds

Energy Technology Data Exchange (ETDEWEB)

Engelmann, R.H.

1997-08-12

The Hanford Facility Dangerous Plaste Permit Application is considered to be a single application organized into a General Information Portion (document number DOE/RL-91-28) and a Unit-Specific Portion. The scope of the Unit-Specific Portion is limited to Part B permit application documentation submitted for individual, `operating` treatment, storage, and/or disposal units, such as the Low-Level Burial Grounds (this document, DOE/RL-88-20).

Female Headdress from Dubrovskiy Burial Ground of 4th–5th Centuries

Directory of Open Access Journals (Sweden)

Krasnopeоrov Alexander A.

2017-03-01

Full Text Available The article examines the remains of a female headdress from Dubrovskiy burial ground of Mazunino type in the Kama region of Udmurtia. The burial is defined by the Migration Period, and the leader of the excavations generally attributed it to the 4th – 5th centuries AD. As widely known, female dress was a status symbol, a sign of belonging to a tribe. The headdress studied here belonged to a young woman, whose status was demonstrated through the context of this collective burial and the grave goods. The type of the headdress is reconstructed by its constructive details, peculiar location of metallic decorations and preserved organics. According to the authors, the headdress had the front part (frontal piece on a solid base with decorative elements, and a soft back part (a shawl with metallic details. The authors refer to archaeological analogies and ethnographic parallels, which allow reconstructing the cultural context of the find.

In-situ high-resolution gamma-spectrometric survey of burial ground-monitoring wells

International Nuclear Information System (INIS)

Bowman, W.W.

1981-09-01

In situ high resolution gamma-ray spectrometry with an intrinsic germanium detector assembly of special design surveyed the burial ground monitoring wells to locate and identify gamma emitters that may have migrated from the burial trenches toward the water table. Gamma-ray spectra were acquired as a function of depth in each well and recorded on magnetic tape. These spectra were reduced by a series of computer programs to produce count rate versus depth profiles for natural and man-made activities. The original spectra and the profiles have been archived on magnetic tape for comparison with similar future surveys. Large amounts of man-made activities were observed in some of the burial trenches; however, below the trench bottoms, only very low but detectable amounts of 60 Co and 137 Cs were observed in eleven wells. The highest level of man-made gamma activity observed below the trench bottoms has a count rate roughly equal to that observed for uranium daughter activities which are natural to the subsoil

Examination of representative drum from 618-9 Burial Ground

International Nuclear Information System (INIS)

Duncan, D.R.; Bunnell, L.R.

1992-10-01

The work described in this report was conducted in pursuance of Task E of the Pacific Northwest Laboratory Solid Waste Technology Support Program for Westinghouse Hanford Company. Task E calls for a determination of the corrosion rate of low-carbon steels under typical Hanford Site conditions. To meet this objective, Pacific Northwest Laboratory examined one intact drum that was judged to be representative of the largely intact drums excavated at the 618-9 Burial Ground located west of the 300 Area at the Hanford Site. Six samples were examined to characterize the drum, its composition, and its corrosion and corrosion products. The drum, which was found empty, was constructed of low-carbon steel. Its surface appeared relatively sound. The drum metal varied in thickness, but the minimum thickness in the samples was near 0.020 in. The corrosion corresponds to approximately 25 to 35 mils of metal loss, roughly a 1 mil/yr corrosion rate. Corrosion products were goethite and maghymite, expected products of iron buried in soil. Apparently, the drum leaked some time ago, but the cause of the leakage is unknown because records of the drums and their burial are limited. The drum was empty when found, and it is possible that it could have failed by pitting rather than by general corrosion. A pitting rate of about 3.5 mils/yr would have caused loss of drum integrity in the time since burial

Treatment/Disposal Plan for Drummed Waste from the 300-FF-1 Operable Unit, 618-4 Burial Ground

International Nuclear Information System (INIS)

Lerch, J.A.

1999-01-01

The objective of this plan is to support selection of a safe, environmentally responsible, and cost-effective treatment and disposal method for drums containing depleted uranium metal chips submerged in oil that have been and will be excavated from the 618-4 Burial Ground. Remediation of the 300-FF-1 Operable Unit, 618-4 Burial Ground was initiated in fiscal year (FY) 1998 as an excavation and removal operation. Routine processes were established to excavate and ship contaminated soil and debris to the Environmental Restoration Disposal Facility (ERDF) for disposal

Environmental analysis burial of offsite low-level waste at SRP

International Nuclear Information System (INIS)

Poe, W.L.; Moyer, R.A.

1980-12-01

The environmental effects of receipt and burial of low-level naval waste generated at Department of Energy Laboratories are assessed in this environmental analysis. Through 1979, this low-level DOE waste was sent to the NRC-licensed burial ground operated by Chem-Nuclear Systems, Inc., at Barnwell, South Carolina. DOE announced on October 26, 1979, that DOE-generated low-level waste would no longer be buried at commercial waste burial sites. SRP was selected to receive the naval waste described in this analysis. Receipt and burial of these wastes will have a negligible effect on SRP's environment and increase only slightly the environmental effects of the SRP operations discussed in the EIS on SRP waste management operations. The environmental effects of burial of this waste at Chem-Nuclear Burial Ground or at the SRP Burial Ground are described in this environmental analysis to permit assessment of incremental effects caused by the decision to bury this naval waste in the SRP Burial Ground rather than in the Barnwell Burial Ground. The radiological effects from burial of this waste in either the SRP or Chem-Nuclear Burial Ground are very small when compared to those from natural background radiation or to the annual population dose commitment from operation of SRP. The environmental effects of burial at SRP to dose commitments normally received by the population surrounding SRP are compared

Cleanup Verification Package for the 118-B-6, 108-B Solid Waste Burial Ground

International Nuclear Information System (INIS)

Proctor, M.L.

2006-01-01

This cleanup verification package documents completion of remedial action for the 118-B-6, 108-B Solid Waste Burial Ground. The 118-B-6 site consisted of 2 concrete pipes buried vertically in the ground and capped by a concrete pad with steel lids. The site was used for the disposal of wastes from the 'metal line' of the P-10 Tritium Separation Project.

Hydrogeology of the 200 Areas low-level burial grounds: An interim report: Volume 1, Text

Energy Technology Data Exchange (ETDEWEB)

Last, G.V.; Bjornstad, B.N.; Bergeron, M.P.; Wallace, D.W.; Newcomer, D.R.; Schramke, J.A.; Chamness, M.A.; Cline, C.S.; Airhart, S.P.; Wilbur, J.S.

1989-01-01

This report presents information derived from the installation of 35 ground-water monitoring wells around six low-level radioactive/hazardous waste burial grounds located in the 200 Areas of the Hanford Site in southeastern Washington State. This information was collected between May 20, 1987 and August 1, 1988. The contents of this report have been divided into two volumes. This volume contains the main text. Volume 2 contains the appendixes, including data and supporting information that verify content and results found in the main text. This report documents information collected by the Pacific Northwest Laboratory at the request of Westinghouse Hanford Company. Presented in this report are the preliminary interpretations of the hydrogeologic environment of six low-level burial grounds, which comprise four waste management areas (WMAs) located in the 200 Areas of the Hanford Site. This information and its accompanying interpretations were derived from sampling and testing activities associated with the construction of 35 ground-water monitoring wells as well as a multitude of previously existing boreholes. The new monitoring wells were installed as part of a ground-water monitoring program initiated in 1986. This ground-water monitoring program is based on requirements for interim status facilities in compliance with the Resource Conservation and Recovery Act (1976).

Ground-penetrating radar in characterizing and monitoring waste-burial sites

International Nuclear Information System (INIS)

Sandness, G.A.; Kimball, C.S.

1982-02-01

Potential environmental hazards are associated with buried chemical and nuclear wastes because of the possibilities of inadvertent excavation or migration of toxic chemicals or radionuclides into groundwater or surface water bodies. Concern is often related to the fact that many existing waste burial sites have been found to be inadequately designed and/or poorly documented. New technology and innovative applications of current technology are needed to locate, characterize, and monitor the wastes contained in such sites. The work described in this paper is focused on the use of ground-penetrating radar (GPR) for those purposes

Low-Level Burial Grounds Dangerous Waste Permit Application design documents

International Nuclear Information System (INIS)

1990-01-01

This document presents the Functional Design Criteria for trenches to be constructed to receive solid radioactive mixed waste (RMW) from on and offsite generators. The new RMW disposal facilities are considered modifications to or lateral expansion of the existing low-level waste burial grounds. The new facilities upgrade the existing disposal practice for RMW to the minimum technology requirements of the Resource Conservation and Recovery Act. The proposed locations for the two facilities are: 218-E-10 for drag-off-waste packages and, 218-W-4C for non drag-off waste packages

The distinguishing characteristics of interlayer oxidation zone and burial ancient ground oxidation zone

International Nuclear Information System (INIS)

Zhang Zhanshi; Zhou Wenbin

1998-01-01

The author discusses the main characteristics of interlayer oxidation zones and the burial ancient ground oxidation zones of Uranium deposit No. 512 in Xinjiang Uigur municipality. The epigenetic genesis, depending on some aquifer, the tongue-like in section, having the zonation along dip direction and having certain mineral assemblage are the typical features for interlayer oxidation zones

A detection-level hazardous waste ground-water monitoring compliance plan for the 200 areas low-level burial grounds and retrievable storage units

International Nuclear Information System (INIS)

1987-02-01

This plan defines the actions needed to achieve detection-level monitoring compliance at the Hanford Site 200 Areas Low-Level Burial Grounds (LLBG) in accordance with the Resource Conservation and Recovery Act (RCRA). Compliance will be achieved through characterization of the hydrogeology and monitoring of the ground water beneath the LLBG located in the Hanford Site 200 Areas. 13 refs., 20 figs

Project TN-030: hydrogeology, ORNL radioactive waste burial grounds. US Geological Survey annual report, FY 82

International Nuclear Information System (INIS)

1982-01-01

Near Burial Ground 3, five wells were cored through Unit F of the Chickamauga Limestone, previously considered to be a probable barrier to ground-water flow. Cores revealed that in this area Unit F actually consists of two continuous silty shale/shaley siltstone members with an interbedded limestone member. Weathering stains in the core and small-size solution openings revealed by televiewer logging indicate that this unit likely has greater permeability than previously described. A unique instrumentation system was designed and installed in six wells to provide information about hydraulic heads in the three geologic units immediately underlying the site. Sediment retrieved from two wells 450 feet and 1300 feet from the site was found to contain as much as 335 pCi/g and 0.83 pCi/g, respectively, of cesium-137. In Burial Ground 5 the construction of four clusters of piezometers of special design was compelted. The deepest wells were cored, geophysical logs were made of each piezometer, and hydraulic conductivities of the bedrock were measured in 50-foot depth increments. No contamination that could be measured by field instrumentation was found in the bedrock. Geophysical logs were made of several older wells in Burial Grounds 5 and 6 and the ILW area. Spectral logging identified the isotopes 60 Co and/or 137 Cs in several well bores. Tritium was found to still be present in water from wells used five years ago during tracer tests in two different areas, suggesting that an inefficient retardive mechanism for this nuclide exists in fine-grained geologic material

Radionuclide migration studies at the Savannah River Plant humid shallow land burial site for low-level waste

International Nuclear Information System (INIS)

Stone, J.A.; Oblath, S.B.; Hawkins, R.H.; Emslie, R.H.; Hoeffner, S.L.; King, C.M.

1984-01-01

A program of field, laboratory, and modeling studies for the Savannah River Plant low-level waste burial ground has been conducted for several years. The studies provide generic data on an operating shallow land burial site in a humid region. Recent results from individual studies on subsurface monitoring, lysimeter tests, soil-water chemistry, and transport modeling are reported. Monitoring continues to show little movement of radionuclides except tritium. Long-term lysimeter tests with a variety of defense wastes measure migration under controlled field conditions. One lysimeter was excavated to study radionuclide distribution on the soil column beneath the waste. New soil-water distribution coefficients (K/sub d/) were measured for Co-60, Sr-90, Ru-106, Sb-125, and I-129. Laboratory and field data are integrated by means of the SRL dose-to-man model, to evaluate effects of alternative disposal practices. The model recently has been used to evaluate TRU disposal criteria and to predict migration behavior of tritium, Tc-99, and I-129. 14 references, 2 tables

Assessment of change in shallow land burial limits for defense transuranic waste

International Nuclear Information System (INIS)

Cohen, J.J.; Smith, C.F.; Spaeth, M.E.; Ciminesi, F.J.; Dickman, P.T.; O'Neal, D.A.

1983-03-01

There is an emerging consensus within the waste management technical community that the current concentration limit of 10 nCi/g for shallow land burial (SLB) of transuranic (TRU) waste is excessively restrictive. A concentration limit for SLB in the range of 100 to 1000 nCi/g is reasonable and justifiable based upon these reasons: Resultant increase in collective radiation dose (total population dose) would be very small, and the net detriment to public health would be negligible. Increasing the limit is cost-effective and could save hundreds of millions of dollars for the national economy over time. The hazard resulting from the increased SLB limit for TRU would be significantly less than that due to many naturally occurring mineral deposits and/or human activities. Expenditures directed toward health and safety conform to the economic law of diminishing returns: as the absolute expenditure increases, the marginal return decreases. Excessive restriction of the TRU concentration limit for SLB needlessly diverts limited resources (time, talent, and money) from other areas of health and safety where they might be more beneficially applied. Despite considerable effort, this study did not find any compelling technical argument to maintain the limit for TRU in SLB at 10 nCi/g. Subsequent to the initial preparation of this document, the US Department of Energy issued DOE Order 5820 which raises the administrative disposal limit for transuranic wastes from 10 nCi/g to 100 nCi/g. In addition, the US Nuclear Regulatory Commission has subsequently proposed and adopted a revised version of regulation 10 CFR 61 in which the disposal limit for shallow land burial of Category C (intruder protected) waste is set at 100 nCi/g

TRU assay system and measurements

International Nuclear Information System (INIS)

Brodzinski, R.L.

1984-02-01

The measurement of the transuranic content of nuclear products or process residues has become increasingly important for the recovery of fissionable material from spent fuel elements, the identification of commercial fuel elements which have not yet reached full burnup, the measurement and recovery of transuranics from discarded or stored waste materials, the determination of the transuranic content in high gamma activity waste material scheduled for disposal, compliance with 10CFR61 by land burial operators/shippers, and the satisfaction of accountability requirements. Active neutron interrogation techniques measure either the prompt neutrons or the beta delayed neutrons from fission products following induced fission. These techniques normally only measure fissile transuranics ( 235 U, 239 Pu, and 241 Pu) and are commonly applied only to contact handleable waste. Passive neutron interrogation techniques, on the other hand, are capable of measuring all transuranics except 235 U with adequate sensitivity and will work on both contact handleable and high gamma activity wastes. Since the passive techniques are senstitive to a wider spectrum of transuranic isotopes than the active techniques, substantially less complex and less expensive than the active systems, and they have proven techniques for measuring small quantities of TRU in high gamma activity packages, the passive neutron TRU assay technology was chosen for development into the instruments discussed in this paper

Chronology of 3rd–5th Century Female Graves from Tarasovo Burial Ground

Directory of Open Access Journals (Sweden)

Goldina Rimma D.

2017-07-01

Full Text Available The article represents the concluding part a series of works by the authors on the dating of burials from the unique 1st–5th century Tarasovo burial ground in the Middle Kama region. The first article was dedicated to the chronology of graves dating back to the early Nyrgynda stage (1st–2nd centuries of this monument. The second and third publications feature an analysis of the chronology of 3rd–5th century male burials. The present work describes 160 female burials of 3rd–5th centuries analyzed from the perspective of chronology. Similarly to previous research, the three main methods employed by the authors of this research include those of formal typology, cultural stratigraphy and the nearest neighbour method. A total of 12 chronological groups were singled out as a result: 1st half of 3rd century A.D. (group 1; 2nd half of 3rd century (2; 3rd century (3; 4th century (group 4; 2nd half of 3rd–4th centuries (5а; 3rd–4th centuries (5б; 1st half of 5th century (6; 2nd half of 5th century (7; 5th century (group 8; 2nd half of 4th–5th centuries (9; 4th–5th centuries (10; 2nd half of 3rd–5th centuries

IMPROVEMENTS IN HANFORD TRANSURANIC (TRU) PROGRAM UTILIZING SYSTEMS MODELING AND ANALYSES

International Nuclear Information System (INIS)

UYTIOCO EM

2007-01-01

Hanford's Transuranic (TRU) Program is responsible for certifying contact-handled (CH) TRU waste and shipping the certified waste to the Waste Isolation Pilot Plant (WIPP). Hanford's CH TRU waste includes material that is in retrievable storage as well as above ground storage, and newly generated waste. Certifying a typical container entails retrieving and then characterizing it (Real-Time Radiography, Non-Destructive Assay, and Head Space Gas Sampling), validating records (data review and reconciliation), and designating the container for a payload. The certified payload is then shipped to WIPP. Systems modeling and analysis techniques were applied to Hanford's TRU Program to help streamline the certification process and increase shipping rates

Development and Testing of Techniques for In-Ground Stabilization, Size Reduction and Safe Removal of Radioactive Wastes Stored in Large Containments in Burial Grounds - 13591

International Nuclear Information System (INIS)

Halliwell, Stephen

2013-01-01

Radioactive waste materials, including Transuranic (TRU) wastes from laboratories have been stored below ground in large containments at a number of sites in the US DOE Complex, and at nuclear sites in Europe. These containments are generally referred to as caissons or shafts. The containments are in a range of sizes and depths below grade. The caissons at the DOE's Hanford site are cylindrical, of the order of 2,500 mm in diameter, 3,050 mm in height and are buried about 6,000 mm below grade. One type of caisson is made out of corrugated pipe, whereas others are made of concrete with standard re-bar. However, the larger shafts in the UK are of the order of 4,600 mm in diameter, 53,500 mm deep, and 12,000 below grade. This paper describes the R and D work and testing activities performed to date to evaluate the concept of in-ground size reduction and stabilization of the contents of large containments similar to those at Hanford. In practice, the height of the Test Facility provided for a test cell that was approximately 22' deep. That prevented a 'full scale mockup' test in the sense that the Hanford Caisson configuration would be an identical replication. Therefore, the project was conducted in two phases. The first phase tested a simulated Caisson with surrogate contents, and part of a Chute section, and the second phase tested a full chute section. These tests were performed at VJ Technologies Test Facility located in East Haven, CT, as part of the Proof of Design Concept program for studying the feasibility of an in-situ grout/grind/mix/stabilize technology for the remediation of four caissons at the 618-11 Burial Ground at US Department of Energy Hanford Site. The test site was constructed such that multiple testing areas were provided for the evaluation of various tools, equipment and procedures under conditions that simulated the Hanford site, with representative soils and layout dimensions. (authors)

Development and Testing of Techniques for In-Ground Stabilization, Size Reduction and Safe Removal of Radioactive Wastes Stored in Large Containments in Burial Grounds - 13591

Energy Technology Data Exchange (ETDEWEB)

Halliwell, Stephen [VJ Technologies Inc, 89 Carlough Road, Bohemia, NY (United States)

2013-07-01

Radioactive waste materials, including Transuranic (TRU) wastes from laboratories have been stored below ground in large containments at a number of sites in the US DOE Complex, and at nuclear sites in Europe. These containments are generally referred to as caissons or shafts. The containments are in a range of sizes and depths below grade. The caissons at the DOE's Hanford site are cylindrical, of the order of 2,500 mm in diameter, 3,050 mm in height and are buried about 6,000 mm below grade. One type of caisson is made out of corrugated pipe, whereas others are made of concrete with standard re-bar. However, the larger shafts in the UK are of the order of 4,600 mm in diameter, 53,500 mm deep, and 12,000 below grade. This paper describes the R and D work and testing activities performed to date to evaluate the concept of in-ground size reduction and stabilization of the contents of large containments similar to those at Hanford. In practice, the height of the Test Facility provided for a test cell that was approximately 22' deep. That prevented a 'full scale mockup' test in the sense that the Hanford Caisson configuration would be an identical replication. Therefore, the project was conducted in two phases. The first phase tested a simulated Caisson with surrogate contents, and part of a Chute section, and the second phase tested a full chute section. These tests were performed at VJ Technologies Test Facility located in East Haven, CT, as part of the Proof of Design Concept program for studying the feasibility of an in-situ grout/grind/mix/stabilize technology for the remediation of four caissons at the 618-11 Burial Ground at US Department of Energy Hanford Site. The test site was constructed such that multiple testing areas were provided for the evaluation of various tools, equipment and procedures under conditions that simulated the Hanford site, with representative soils and layout dimensions. (authors)

Searching for the IRA "disappeared": ground-penetrating radar investigation of a churchyard burial site, Northern Ireland.

Science.gov (United States)

Ruffell, Alastair

2005-11-01

A search for the body of a victim of terrorist abduction and murder was made in a graveyard on the periphery of a major conurbation in Northern Ireland. The area is politically sensitive and the case of high profile. This required non-invasive, completely non-destructive and rapid assessment of the scene. A MALA RAMAC ground-penetrating radar system was used to achieve these objectives. Unprocessed and processed 400 MHz data show the presence of a collapse feature above and around a known 1970s burial with no similar collapse above the suspect location. In the saturated, clay-rich sediments of the site, 200 MHz data offered no advantage over 400 MHz data. Unprocessed 100 MHz data shows a series of multiples in the known burial with no similar features in the suspect location. Processed 100 MHz lines defined the shape of the collapse around the known burial to 2 m depth, together with the geometry of the platform (1 m depth) the gravedigger used in the 1970s to construct the site. In addition, processed 100 MHz data showed both the dielectric contrast in and internal reflection geometry of the soil imported above the known grave. Thus the sequence, geometry, difference in infill and infill direction of the grave was reconstructed 30 years after burial. The suspect site showed no evidence of shallow or deep inhumation. Subsequently, the missing person's body was found some distance from this site, vindicating the results and interpretation from ground-penetrating radar. The acquisition, processing, collapse feature and sequence stratigraphic interpretation of the known burial and empty (suspect) burial site may be useful proxies for other, similar investigations. GPR was used to evaluate this site within 3 h of the survey commencing, using unprocessed data. An additional day of processing established that the suspect body did not reside here, which was counter to police and community intelligence.

Cleanup Verification Package for the 118-F-3, Minor Construction Burial Ground

International Nuclear Information System (INIS)

Appel, M.J.

2007-01-01

This cleanup verification package documents completion of remedial action for the 118-F-3, Minor Construction Burial Ground waste site. This site was an open field covered with cobbles, with no vegetation growing on the surface. The site received irradiated reactor parts that were removed during conversion of the 105-F Reactor from the Liquid 3X to the Ball 3X Project safety systems and received mostly vertical safety rod thimbles and step plugs

Waste Analysis Plan for the Low-Level Burial Grounds [CANCELLED] Reissued as HNF-5841

International Nuclear Information System (INIS)

ELLEFSON, M.D.

2000-01-01

Canceled see HNF-5841 Rev 0. This waste analysis plan (WAP) has been prepared for the Low-Level Burial Grounds which are located in the 200 East and West Areas of the Hanford Facility, Richland, Washington. This WAP documents the methods used to characterize, obtain and analyze representative samples of waste managed at this unit

Transuranic element uptake and cycling in a forest over an old burial ground

International Nuclear Information System (INIS)

Murphy, C.E. Jr.; Tuckfield, J.C.

1992-01-01

The consequences of returning the Savannah River Site (SRS) burial ground area to general public access at the time of completion of the SRS mission is being investigated. This study includes evaluation of the radiological impact to inhabitants of the area under a number of scenarios that include the return of the land to farming or forestry use with or without exhumation of the buried waste

Characterization of the Hanford 300 area burial grounds. Task IV. Biological transport

International Nuclear Information System (INIS)

Fitzner, R.E.; Gano, K.A.; Rickard, W.H.; Rogers, L.E.

1979-10-01

The characteristics of radioactive waste burial sites at the 300 area burial grounds on the Department of Energy's Hanford Site, southeastern Washington were studied. The potential vectors of radionuclide transport studied were vegetation and animals. The overall results showed a low potential for uptake and transport of radionuclides from the 300 area sites. However, additional methods to control physical and biological mechanisms may contribute to the effectiveness of waste burial practices. From the results, the Biological Transport task recommended field studies which include reduction of soil erosion and addition of biobarriers to plants and animals. Vegetation plays a major role in reducing soil erosion, and thereby maintaining the backfill over the burial sites. Of the several species found on the 300 area sites, cheatgrass (Bromus tectorum) appears to be the most desirable as a cover. Besides retarding erosion, it has a shallow root system (does not easily penetrate buried material); it has a low affinity for radionuclide uptake; and its tissues are not easily blown away. Small mammals (specifically, mice) appear to have the most potential for radionuclide exposure and uptake. Small mammals were live-trapped within 10 x 10-meter trap grids. Each animal trapped was surgically implanted with a thermoluminescent dosimeter. When the animal was recaptured, the dosimeter was removed and read for exposure. Exposures were reported in milli-Roentgens. The most consistently trapped small mammals were the Great Basin pocket mouse (Perognathus parvus) and the deer mouse (Peromyscus maniculatus). Results from the dosimeter readings showed that some of those animals had higher than background exposures. Biobarriers to animals could be considered as a mechanism to reduce the potential for radionuclide transport

Characterization of the Hanford 300 area burial grounds. Task IV. Biological transport

Energy Technology Data Exchange (ETDEWEB)

Fitzner, R.E.; Gano, K.A.; Rickard, W.H.; Rogers, L.E.

1979-10-01

The characteristics of radioactive waste burial sites at the 300 area burial grounds on the Department of Energy's Hanford Site, southeastern Washington were studied. The potential vectors of radionuclide transport studied were vegetation and animals. The overall results showed a low potential for uptake and transport of radionuclides from the 300 area sites. However, additional methods to control physical and biological mechanisms may contribute to the effectiveness of waste burial practices. From the results, the Biological Transport task recommended field studies which include reduction of soil erosion and addition of biobarriers to plants and animals. Vegetation plays a major role in reducing soil erosion, and thereby maintaining the backfill over the burial sites. Of the several species found on the 300 area sites, cheatgrass (Bromus tectorum) appears to be the most desirable as a cover. Besides retarding erosion, it has a shallow root system (does not easily penetrate buried material); it has a low affinity for radionuclide uptake; and its tissues are not easily blown away. Small mammals (specifically, mice) appear to have the most potential for radionuclide exposure and uptake. Small mammals were live-trapped within 10 x 10-meter trap grids. Each animal trapped was surgically implanted with a thermoluminescent dosimeter. When the animal was recaptured, the dosimeter was removed and read for exposure. Exposures were reported in milli-Roentgens. The most consistently trapped small mammals were the Great Basin pocket mouse (Perognathus parvus) and the deer mouse (Peromyscus maniculatus). Results from the dosimeter readings showed that some of those animals had higher than background exposures. Biobarriers to animals could be considered as a mechanism to reduce the potential for radionuclide transport.

Hydrology of the solid waste burial ground, as related to the potential migration of radionuclides, Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Barraclough, J.T.; Robertson, J.B.; Janzer, V.J.; Saindon, L.G.

1976-08-01

This report describes a study conducted by the U. S. Geological Survey with the following objectives: to evaluate the hydrologic, radiologic and geochemical variables that control the potential for subsurface migration of waste radionuclides from the burial trenches to the Snake River Plain aquifer; to determine the extent of radionuclide migration, if any; and, to construct monitoring wells into the aquifer. Statistically significant trace amounts of radioactivity were found in about one-half of the 44 sedimentary samples from the six holes core drilled inside the burial ground and from all water samples from one hole tapping a perched water table. These very low levels of radioactivity are detectable only with the most sensitive of analytical equipment and techniques. The levels of radioactivity detected were, in most cases, less than the amounts found in surface soils in this region resulting from world-wide fallout. This radioactivity found in the cores could have been introduced naturally by migration by infiltrating water which had made contact with buried waste or could have been introduced artificially during drilling and sampling. The available data from the four peripheral monitoring wells do not indicate that radionuclide constituents from the burial ground have migrated into the underlying Snake River Plain aquifer. The low concentrations of radionuclides detected in samples taken from the sedimentary layers are not expected to migrate to the Snake River Plain aquifer. Water samples from the peripheral wells and one core hole inside the burial ground will continue to be collected and analyzed for radioactivity semi-annually

Hydrogeology of the 200 Areas low-level burial grounds: An interim report: Volume 2, Appendixes

Energy Technology Data Exchange (ETDEWEB)

Last, G.V.; Bjornstad, B.N.; Bergeron, M.P.; Wallace, D.W.; Newcomer, D.R.; Schramke, J.A.; Chamness, M.A.; Cline, C.S.; Airhart, S.P.; Wilbur, J.S.

1989-01-01

This report presents information derived form the installation of 35 ground-water monitoring wells around six low-level radioactive/hazardous waste burial grounds located in the 200 Areas of the Hanford Site in southeastern Washington State. This information was collected between May 20, 1987 and August 1, 1988. The contents of this report have been divided into two volumes. Volume 1 contains the main text. This Volume contains the appendixes, including data and supporting information that verify content and results found in the main text.

SLOPE STABILITY EVALUATION AND EQUIPMENT SETBACK DISTANCES FOR BURIAL GROUND EXCAVATIONS

Energy Technology Data Exchange (ETDEWEB)

MCSHANE DS

2010-03-25

After 1970 Transuranic (TRU) and suspect TRU waste was buried in the ground with the intention that at some later date the waste would be retrieved and processed into a configuration for long term storage. To retrieve this waste the soil must be removed (excavated). Sloping the bank of the excavation is the method used to keep the excavation from collapsing and to provide protection for workers retrieving the waste. The purpose of this paper is to document the minimum distance (setback) that equipment must stay from the edge of the excavation to maintain a stable slope. This evaluation examines the equipment setback distance by dividing the equipment into two categories, (1) equipment used for excavation and (2) equipment used for retrieval. The section on excavation equipment will also discuss techniques used for excavation including the process of benching. Calculations 122633-C-004, 'Slope Stability Analysis' (Attachment A), and 300013-C-001, 'Crane Stability Analysis' (Attachment B), have been prepared to support this evaluation. As shown in the calculations the soil has the following properties: Unit weight 110 pounds per cubic foot; and Friction Angle (natural angle of repose) 38{sup o} or 1.28 horizontal to 1 vertical. Setback distances are measured from the top edge of the slope to the wheels/tracks of the vehicles and heavy equipment being utilized. The computer program utilized in the calculation uses the center of the wheel or track load for the analysis and this difference is accounted for in this evaluation.

Slope Stability Evaluation And Equipment Setback Distances For Burial Ground Excavations

International Nuclear Information System (INIS)

Mcshane, D.S.

2010-01-01

After 1970 Transuranic (TRU) and suspect TRU waste was buried in the ground with the intention that at some later date the waste would be retrieved and processed into a configuration for long term storage. To retrieve this waste the soil must be removed (excavated). Sloping the bank of the excavation is the method used to keep the excavation from collapsing and to provide protection for workers retrieving the waste. The purpose of this paper is to document the minimum distance (setback) that equipment must stay from the edge of the excavation to maintain a stable slope. This evaluation examines the equipment setback distance by dividing the equipment into two categories, (1) equipment used for excavation and (2) equipment used for retrieval. The section on excavation equipment will also discuss techniques used for excavation including the process of benching. Calculations 122633-C-004, 'Slope Stability Analysis' (Attachment A), and 300013-C-001, 'Crane Stability Analysis' (Attachment B), have been prepared to support this evaluation. As shown in the calculations the soil has the following properties: Unit weight 110 pounds per cubic foot; and Friction Angle (natural angle of repose) 38 o or 1.28 horizontal to 1 vertical. Setback distances are measured from the top edge of the slope to the wheels/tracks of the vehicles and heavy equipment being utilized. The computer program utilized in the calculation uses the center of the wheel or track load for the analysis and this difference is accounted for in this evaluation.

Mixed Waste Management Facility (MWMF) Old Burial Ground (OBG) source control technology and inventory study

Energy Technology Data Exchange (ETDEWEB)

Flach, G.P.; Rehder, T.E.; Kanzleiter, J.P.

1996-10-02

This report has been developed to support information needs for wastes buried in the Burial Ground Complex. Information discussed is presented in a total of four individual attachments. The general focus of this report is to collect information on estimated source inventories, leaching studies, source control technologies, and to provide information on modeling parameters and associated data deficiencies.

Mixed Waste Management Facility (MWMF) Old Burial Ground (OBG) source control technology and inventory study

International Nuclear Information System (INIS)

Flach, G.P.; Rehder, T.E.; Kanzleiter, J.P.

1996-01-01

This report has been developed to support information needs for wastes buried in the Burial Ground Complex. Information discussed is presented in a total of four individual attachments. The general focus of this report is to collect information on estimated source inventories, leaching studies, source control technologies, and to provide information on modeling parameters and associated data deficiencies

Compliance For Hanford Waste Retrieval: Radioactive Air Emissions

International Nuclear Information System (INIS)

Simmons, F.M.

2009-01-01

(sm b ullet) Since 1970, approximately 38,000 suspect transuranic (TRU) and TRU waste cont∼iners have been placed in retrievable storage on the Hanford Site in the 200Area's burial grounds. (sm b ullet) TRU waste is defined as waste containing greater than 100 nanocuries/gram of alpha emitting transuranic isotopes with half lives greater than 20 years. (sm b ullet) The United States currentl∼permanently disposes of TRU waste at the Waste Isolation Pilot Plant (WIPP).

Final Hazard Categorization for the Remediation of the 118-D-1, 118-D-2, 118-D-3, 118-H-1, 118-H-2, and 118-H-3 Solid Waste Burial Grounds

Energy Technology Data Exchange (ETDEWEB)

J.D. Ludowise

2009-06-17

This report presents the final hazard categorization for the remediation of the 118-D-1, 118-D-2, 118-D-3 Burial Grounds located within the 100-D/DR Area of the Hanford Site and the 118-H-1, 118-H-2, and 118-H-3 Burial Grounds located within the 100-H Area of the Hanford Site. A material at risk calculation was performed that determined the radiological inventory for each burial ground to be Hazard Category 3.

Interim Action Proposed Plan for the old radioactive waste burial ground (643-E)

International Nuclear Information System (INIS)

McFalls, S.

1995-12-01

This Interim Action Proposed (IAPP) is issued by the U.S. Department of Energy (DOE), which functions as the lead agency for SRS remedial activities, and with concurrence by the U.S. Environmental Protection Agency (EPA) and the South Carolina Department of Health and Environmental Control (SCDHEC). The purpose of this IAPP is to describe the preferred interim remedial action for addressing the Old Radioactive Waste Burial Ground (ORWBG) unit located in the Burial Ground Complex (BGC) at the Savannah River Site (SRS) in Aiken, South Carolina. On December 21, 1989, SRS was included on the National Priorities List (NPL). In accordance with Section 120 of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), DOE has negotiated a Federal Facility Agreement (FFA, 1993) with EPA and SCDHEC to coordinate remedial activities at SRS. Public participation requirements are listed in Sections 113 and 117 of CERCLA. These requirements include establishment of an Administrative Record File that documents the selection of remedial alternatives and allows for review and comment by the public regarding those alternatives. The SRS Public Involvement Plan (PIP) (DOE, 1994) is designed to facilitate public involvement in the decision-making process for permitting closure, and the selection of remedial alternatives. Section 117(a) of CERCLA, 1980, as amended, requires publication of a notice of any proposed remedial action

Conceptual system for removal of plutonium from soils and scrap

International Nuclear Information System (INIS)

Bruns, L.E.

1982-01-01

An integrated conceptual scheme for processing TRU wastes and sediments retrieved from a typical TRU-burial ground is presented. This scheme features (a) use of a High Gradient Magnetic System to separate a TRU (e.g., Pu and Am) fraction containing materials from inert soil particles, (b) leaching of the TRU fraction with HNO 3 -HF and (c) operation of a TOPO-CCl 4 reflux-type solvent extraction system to concentrate actinides into a very small volume of product solution

Evaluation of a TRU fundamental criterion and reference TRU waste units

International Nuclear Information System (INIS)

Klett, R.

1993-01-01

The comparison of two options for regulating transuranic (TRU) waste disposal is explained in this paper. The two options are (1) fundamental and derived standards developed specifically for the TRU waste and (2) a family of procedures that use a reference to the TRU waste unit with procedures that use a reference to the TRU waste unit with commercial high-level waste (HLW) criteria. Background information pertaining to both options is covered. A section on criteria specifically for TRUE waste suggests a methodology for developing or adapting fundamental and derived criteria that are consistent with all other aspects of the standards. The section on references TRU waste units covers all the parameter variations that have been suggested for this option. The technical bases of each approach is reviewed, implementation is discussed and their relative attributes and deficiencies are evaluated

Long-Term Performance of Transuranic Waste Inadvertently Disposed in a Shallow Land Burial Trench at the Nevada Test Site

International Nuclear Information System (INIS)

Shott, Gregory J.; Yucel, Vefa

2009-01-01

In 1986, 21 m3 of transuranic (TRU) waste was inadvertently disposed in a shallow land burial trench at the Area 5 Radioactive Waste Management Site on the Nevada Test Site. U.S. Department of Energy (DOE) TRU waste must be disposed in accordance with Title 40, Code of Federal Regulations (CFR), Part 191, Environmental Radiation Protection Standard for Management and Disposal of Spent Nuclear Fuel, High-Level, and Transuranic Radioactive Wastes. The Waste Isolation Pilot Plant is the only facility meeting these requirements. The National Research Council, however, has found that exhumation of buried TRU waste for disposal in a deep geologic repository may not be warranted when the effort, exposures, and expense of retrieval are not commensurate with the risk reduction achieved. The long-term risks of leaving the TRU waste in-place are evaluated in two probabilistic performance assessments. A composite analysis, assessing the dose from all disposed waste and interacting sources of residual contamination, estimates an annual total effective dose equivalent (TEDE) of 0.01 mSv, or 3 percent of the dose constraint. A 40 CFR 191 performance assessment also indicates there is reasonable assurance of meeting all requirements. The 40 CFR 191.15 annual mean TEDE for a member of the public is estimated to reach a maximum of 0.055 mSv at 10,000 years, or approximately 37 percent of the 0.15 mSv individual protection requirement. In both assessments greater than 99 percent of the dose is from co-disposed low-level waste. The simulated probability of the 40 CFR 191.13 cumulative release exceeding 1 and 10 times the release limit is estimated to be 0.0093 and less than 0.0001, respectively. Site characterization data and hydrologic process modeling support a conclusion of no groundwater pathway within 10,000 years. Monte Carlo uncertainty analysis indicates that there is reasonable assurance of meeting all regulatory requirements. Sensitivity analysis indicates that the results

Transuranic element uptake and cycling in a forest over an old burial ground

International Nuclear Information System (INIS)

Murphy, C.E.; Tuckfield, R.C.

1994-01-01

The consequences of returning the Savannah River Site (SRS) burial ground area to general public access at the time of completion of the SRS mission is being investigated. This study was established with the objective of determining the uptake of buried, low-level, transuranic waste from unlined earthen trenches by forest vegetation. From SRS startup in 1953 through 1974, solid waste contaminated with α-emitting transuranic nuclides was buried, unencapsulated, in earthen trenches. Burial records show that this material includes plutonium-238 ( 238 Pu), plutonium isotopes 239 and 240 ( 239,240 Pu), americium-241 ( 241 Am), and neptunium-237 ( 237 Np). In 1979, two tree plots were established, one over a trench in the burial ground and the other in an area without trenches. In the 2 years following establishment of the tree plots, 1979 and 1980, whole trees of each species were collected from each plot and analyzed for 239 Pu and 238 Pu. Beginning in 1986, needle samples were collected from selected pine trees in each of the plots. Because of poor growth and survival, the hardwood trees were not sampled after 1980. The results of data analysis support the conclusions that: (1) there is more 238 Pu uptake by pine tree seedlings than the other species, (2) there is greater transuranic radionuclide uptake in grown pine trees than in seedlings, and (3) there are greater concentrations of transuranic radionuclides in the grown pine trees on the trench plots than in the pine trees on the control plot. These data indicate that tree roots will extract transuranic isotopes from buried, low level waste. The amount of radioisotopes moved from the trenches to the surface is small and the level in the trees is low enough that dose from direct exposure will be very small. A model was developed to estimate the potential for the transfer from the SRS alpha trenches. The results suggest that even following 100 years of transport, the transuranic, alpha dose from consuming food crops

TRU partnership-benefits to the national TRU program

International Nuclear Information System (INIS)

Lippis, J.; Lott, S.A.

1995-01-01

Because increased regulatory authority has been given to the states, the management of transuranic (TRU) wastes varies considerably. One effective tool for facilitating better communications, coordination, and cooperation among the generator/storage sites is the formation of topic specific interface working groups. The National TRU Program supports these groups, and in 1994, a policy was adopted to manage these interface working groups

Two items: Transcription of a presentation by Dr. E. L. Albenesius, ''SRS burial ground operation from an historical perspective''; video tape entitled ''Burial ground operation''

International Nuclear Information System (INIS)

Holcomb, H.P.

1992-01-01

On February 6, 1992, approximately 35 SRS personnel from DOE, WSRC, and Dames and Moore attended a very informative talk given by Dr. E.L. Albenesius who discussed the operation of the SRS Burial Ground from an historical perspective. Dr. Albenesius, a Du Point retiree, formerly served as research manager of SRL's Environmental Effects and Solid Waste Management Technology Divisions among other assignments. One notable point Dr. Albenesius made was in answer to a question concerning what was the most important thing that could be done to reduce the hazard to man from buried waste. His response was to remove as much plutonium as practical prior to closure. In order to preserve this valuable information for the record, the program was audiotaped from which a point-by-point chronological transcription, with minor editing, was prepared

Chronology of the Third – Fifth Centuries Male Graves from the Tarasovo Burial Ground

Directory of Open Access Journals (Sweden)

Goldina Rimma D.

2016-09-01

Full Text Available The article focuses on the chronological attribution of male graves from the late Mazunino stage of the Tarasovo burial ground and is a sequel to an earlier article about dating of the early Nyrgynda stage (1st – 2nd centuries of the same site. The three main methods employed in this research include those of formal typology, cultural stratigraphy and the nearest neighbor method. Eighty-six male graves of the third-fifth centuries were analyzed, with 12 identified as a result: first half of the 3rd c. AD (group 1, second half of the 3rd c. AD (2; 3rd c. (3; first half of the 4th c. (group 4; second half of the 3rd – 4th c. (5; third quarter of the 4th c. (6; fourth quarter of the 4th c. (group 7; second half of the 4th c. (8; second half of the 4th – 5th c. (9; 4th – 5th cc. (10; second half of the 3rd – 5th cc. (11 and 3rd – 5th cc. (12. This article minutes investigates the first six groups, while the rest will be covered in the next publication. Artifacts form the third – fifth century female graves of the Tarasovo burial ground will be studied separately.

Guidelines for selecting codes for ground-water transport modeling of low-level waste burial sites. Executive summary

International Nuclear Information System (INIS)

Simmons, C.S.; Cole, C.R.

1985-05-01

This document was written to provide guidance to managers and site operators on how ground-water transport codes should be selected for assessing burial site performance. There is a need for a formal approach to selecting appropriate codes from the multitude of potentially useful ground-water transport codes that are currently available. Code selection is a problem that requires more than merely considering mathematical equation-solving methods. These guidelines are very general and flexible and are also meant for developing systems simulation models to be used to assess the environmental safety of low-level waste burial facilities. Code selection is only a single aspect of the overall objective of developing a systems simulation model for a burial site. The guidance given here is mainly directed toward applications-oriented users, but managers and site operators need to be familiar with this information to direct the development of scientifically credible and defensible transport assessment models. Some specific advice for managers and site operators on how to direct a modeling exercise is based on the following five steps: identify specific questions and study objectives; establish costs and schedules for achieving answers; enlist the aid of professional model applications group; decide on approach with applications group and guide code selection; and facilitate the availability of site-specific data. These five steps for managers/site operators are discussed in detail following an explanation of the nine systems model development steps, which are presented first to clarify what code selection entails

Waste analysis plan for the low-level burial grounds. Revision 2

International Nuclear Information System (INIS)

Pratt, D.A.

1997-01-01

The purpose of this waste analysis plan (WAP) is to document the waste 5 acceptance process, sampling methodologies, analytical techniques, and overall 6 processes that are undertaken for waste accepted for disposal at the Low-Level 7 Burial Grounds (LLBG), which are located in the 200 East and 200 West Areas of 8 the Hanford Facility, Richland, Washington. Because dangerous waste does not 9 include the source, special nuclear, and by-product material components of 10 mixed waste, radionuclides are not within the scope of this documentation. 11 The information on radionuclides is provided only for general knowledge. The 12 LLBG also receive low-level radioactive waste for disposal. The requirements 13 of this WAP are not applicable to this low-level waste

Treatability tests on water from a low-level waste burial ground

International Nuclear Information System (INIS)

Taylor, P.A.

1990-01-01

Lab-scale treatability tests on trench water from a low-level waste burial ground have shown that the water can be successfully treated by existing wastewater treatment plants at Oak Ridge National Laboratory. Water from the four most highly contaminated trenches that had been identified to date was used in the treatability tests. The softening and ion exchange processes used in the Process Wastewater Treatment Plant removed Sr-90 from the trench water, which was the only radionuclide present at above the discharge limits. The air stripping and activated carbon adsorption processes used in the Nonradiological Wastewater Treatment Plant removed volatile and semi-volatile organics, which were the main contaminants in the trench water, to below detection limits. 6 refs., 2 figs., 7 tabs

Electromagnetic survey of the K1070A burial ground at the Oak Ridge K-25 Site, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

Nyquist, J.E.; Emery, M.S.

1993-01-01

The K1070A burial ground, located at the K-25 Site on the Oak Ridge Reservation, received chemical and radioactive wastes from the late 1940s until 1975. Analysis of water samples collected from nearby monitoring wells indicates that contamination is migrating offsite. In November 1991, Oak Ridge National Laboratory (ORNL) personnel collected high-resolution electrical terrain conductivity data at the K1070A burial ground. A Model EM31 terrain conductivity meter manufactured by Geonics Limited was used in conjunction with the ORNL-developed Ultrasonic Ranging and Data System (USRADS) to perform the survey. The purposeof the survey was to provide Environmental Restoration (ER) staff with a detailed map of the spatial variation of the apparent electrical conductivity of the shallow subsurface (upper 3 m) to assist them in siting future monitoring wells closer to the waste area without drilling into the buried waste

Shallow land burial of radioactive wastes

International Nuclear Information System (INIS)

Jacobs, D.G.; Rose, R.R.

1985-01-01

The authors discuss low-level, solid radioactive wastes buried in the ground since the startup of nuclear operations by the Manhattan Engineer District in the early 1940's. These operations were originally intended to be temporary so the primary consideration in locating land burial sites was their accessibility from the source of waste production. Early land-burial facilities were located on large reservations owned by the U.S. Atomic Energy Commission (AEC) and operated by their prime contractors. Shallow land burial consists of excavating a trench or vault, emplacing the waste, minimizing void space within the disposal unit, and covering the waste with earth to control access to the waste. Problems encountered in the land-burial of radioactive wastes are classified into areas which relate to the environmental characteristics of the sites, waste characteristics, operational practices and control, and predictive capability. The most serious environmentally related problems involve water management. Water provides primary vehicle for both erosional processes, which affect the structural integrity of the waste trenches, and for the migration of radionuclides. Although there is consensus that the current level of off-site movement of radionuclides from operating burial grounds does not constitute an immediate health hazard, there is less certainty with respect to the ability of the facilities to provide long-term containment and isolation

Savannah River Laboratory dose-to-man model. Appendix A. Deterministic studies - SRL Model

International Nuclear Information System (INIS)

Root, R.W. Jr.

1981-01-01

Solid waste contaminated with radionuclides has been buried at the Savannah River Plant (SRP) burial ground since 1953. The radionuclides include alpha-emitting transuranium (TRU) nuclides, beta- and gamma-emitting activation and fission products, and tritium. To evaluate current operating limits for burial of this waste and to aid planning for the eventual decommissioning of the burial ground, the long-term dose to man from each type of waste must be estimated. The dose projections will provide guidance in choosing alternatives for a burial ground decommissioning plan. Such alternatives may include exhuming selected segments of the waste to reduce the long-lived radionuclide inventory or providing additional backfill over the waste trenches. The sensitivity of dose projections to the length of institutional control over the burial ground will provide an estimate of the minimum time period such control must be maintained

Classification of burial rituals of the cemeteries without burial mounds in regions of the Tsarevskoe ancient settlement

Directory of Open Access Journals (Sweden)

Nedashkovsky Leonard F.

2015-09-01

Full Text Available Article is dedicated to analysis of burial rituals of the Golden Horde cemeteries without burial mounds in surroundings of the Tsarevskoe ancient settlement. 51 burials (19.9% of total number in mausoleums or in crypts can be attributed as burials of the Golden Horde aristocracy. In the graves found without burial mounds the most wide-spread were of western, south-western and north-western (which could be considered as azimuth deviation from western orientations (they comprise 94.9% of all burials, which are peculiar to the majority of the urban Muslim population of the Golden Horde. However it must be considered that 56 from these burials (21.9% of total number are burials of necropolis of the population of Old Russian settlement of the Vodyanskoe site. Comparing the aristocratic (in mausoleums and crypts burials without burial mounds in the Lower Volga, it is possible conclude that their percentage was significantly higher in the region of the Tsarevskoe settlement, than in other regions; these data allow to assume here the greatest density of residence of settled elite of the Golden Horde. The smallest share of Muslim burials in coffins in the Lower Volga (44.9% and the maximal one of burials with grave goods (13.6% recorded in the region of the Tsarevskoe site. Burial grounds in the region of the Tsarevskoe ancient settlement were in vicinity of the settlements, that is clearly testified about the degree of territorial closeness of cemeteries of settled population of the Golden Horde with urban and rural settlements of the considered period.

Burial of downed deadwood is strongly affected by log attributes, forest ground vegetation, edaphic conditions, and climate zones

Science.gov (United States)

Jogeir N. Stokland; Christopher W. Woodall; Jonas Fridman; Göran Ståhl

2016-01-01

Deadwood can represent a substantial portion of forest ecosystem carbon stocks and is often reported following good practice guidance associated with national greenhouse gas inventories. In high-latitude forest ecosystems, a substantial proportion of downed deadwood is overgrown by ground vegetation and buried in the humus layer. Such burial obfuscates the important...

Groundwater monitoring in the Savannah River Plant Low Level Waste Burial Ground

Energy Technology Data Exchange (ETDEWEB)

Carlton, W.H.

1983-12-31

This document describes chemical mechanisms that may affect trace-level radionuclide migration through acidic sandy clay soils in a humid environment, and summarizes the extensive chemical and radiochemical analyses of the groundwater directly below the SRP Low-Level Waste (LLW) Burial Ground (643-G). Anomalies were identified in the chemistry of individual wells which appear to be related to small amounts of fission product activity that have reached the water table. The chemical properties which were statistically related to trace level transport of Cs-137 and Sr-90 were iron, potassium, sodium and calcium. Concentrations on the order of 100 ppM appear sufficient to affect nuclide migration. Several complexation mechanisms for plutonium migration were investigated.

On the Problem Related to Reconstructing the Social Structure of the Population that Had Founded Seliksa-Trofimovka (Ancient Mordovian Burial Ground in 4th—5th Centuries

Directory of Open Access Journals (Sweden)

Grishakov Valeriy V.

2013-12-01

Full Text Available The article is devoted to the problem of reconstruction of the social structure of the ancient Monrovian population that had established the 4th-5th-century Seliksa-Trofimovka burial ground in the Upper Sura river region. The materials of the male burials of the necropolis have been chosen for analysis as most socially informative. An attempt has been made to determine the relationship between the social status of the individual and its expression in ritual rites. The differences in the composition and quantity of grave goods made it possible to distinguish three groups of burials conventionally termed as "the poor", "the ordinary" and "the warriors." The latter group included three graves with swords. The necropolis has a row-based order layout; all the burials are on the ground level, with no traces of gravestones, and have the same northeast orientation. The property-based stratification in the analyzed community was apparently insignificant, while social stratification depended primarily on professional activities.

[The sanitary and hygienic state of solid garbage burial grounds in the stages of a life cycle].

Science.gov (United States)

Zomarev, A M; Vaĭsman, Ia I; Zaĭtseva, T A; Glushankova, I S

2010-01-01

The purpose of the study was to assess the sanitary-and-hygienic state of solid garbage (SG) burial grounds in the Perm Territory in different stage of a life cycle. This paper presents the results of the study of deposited waste, forming dump soil, and SG ground emissions by general sanitary and sanitary-microbiological parameters and their effect on environmental objects. The performed studies of the sanitary-and-hygienic situation on some grounds of the Perm Territory suggest that there is a need for setting up a system for sanitary-and-monitoring of SG ground and for elaborating engineering, organizational, and prophylactic measures to assure the sanitary-and-hygienic safety of objects and to control the quality and quantity of waste to be buried and the currents of emissions (ground body degassing, filtrating sewage drainage and purification).

Final Hazard Categorization for the Remediation of the 118-D-1, 118-D-2, 118-D-3, 118-H-1, 118-H-2 and 118-H-3 Solid Waste Burial Grounds

Energy Technology Data Exchange (ETDEWEB)

K. L. Vialetti

2008-05-20

This report presents the final hazard categorization for the remediation of the 118-D-1, 118-D-2, and 118-D-3 Burial Grounds located within the 100-D/DR Area of the Hanford Site and the 118-H-1, 118-H-2, and 118-H-3 Burial Grounds located within the 100-H Area of the Hanford Site.

Radioactive solid waste inventories at United States Department of Energy burial and storage sites

International Nuclear Information System (INIS)

Watanabe, T.

1986-06-01

Radioactive solid waste inventories are given for United States Department of Energy (DOE) burial and storage sites. These data are obtained from the Solid Waste Information Management System (SWIMS) and reflect the inventories as of the end of the calendar year 1985. This report differs from previous issues in that the data cutoff date is December 31, 1985, rather than the fiscal year end. Another difference from previous issues is that data for the TRU categories 1 and 6 have been omitted

TRU partnership-Working smarter-Not harder

International Nuclear Information System (INIS)

Armstrong, D.W.; Briggs, S.R.; Martin, M.R.; Turner, D.R.

1994-01-01

The open-quotes TRU Partnershipclose quotes was initiated and continues to function under the catch phrase philosophy of open-quotes work smarter, not harderclose quotes. The parntership participants have realized that DOE no longer has the funding available to reinvent the wheel at each site. Information and experiences from each site need to accurately and timely provided to the other sites for their use. The project teams from the different TRU waste handling sites benefit enormously from the strong network that has developed between TRU partnership participants. The partnership working interface places design manager in touch with design manager, project manager with project manager, etc. across site boundaries, and equally important, across corporate boundaries. The TRU Partnership has created a team atmosphere for the participants. The team focus is on the common challenge of managing TRU waste projects to support site needs and the needs of the national TRU waste program. Although consistency of approach for all projects at any given site is important, the TRU Partnership provides an intersite forum to establish consistency and understanding across all DOE projects managing TRU waste. The TRU Partnership has adopted the Westinghouse Electric Corporation open-quotes Savings Through Sharingclose quotes philosophy as an integral part of its organizational objectives. As applied by the group, the approach concentrates on information and experiences that can enhance development and reduce costs for (TRU) waste projects

Actinide-soil interactions in waste management at the Savannah River Plant

International Nuclear Information System (INIS)

Holcomb, H.P.; Horton, J.H.; Wilhite, E.L.

1976-01-01

Three aspects of the transuranium (TRU) nuclide-soil interaction were studied in connection with Savannah River Plant (SRP) burial ground operations. Results of the studies are reported as three separate parts of this report

Corrective Measures Study Modeling Results for the Southwest Plume - Burial Ground Complex/Mixed Waste Management Facility

International Nuclear Information System (INIS)

Harris, M.K.

1999-01-01

Groundwater modeling scenarios were performed to support the Corrective Measures Study and Interim Action Plan for the southwest plume of the Burial Ground Complex/Mixed Waste Management Facility. The modeling scenarios were designed to provide data for an economic analysis of alternatives, and subsequently evaluate the effectiveness of the selected remedial technologies for tritium reduction to Fourmile Branch. Modeling scenarios assessed include no action, vertical barriers, pump, treat, and reinject; and vertical recirculation wells

Final Hazard Categorization for the Remediation of the 118-D-1, 118-D-2, 118-D-3, 118-H-1, 118-H-2, and 118-H-3 Solid Waste Burial Grounds

International Nuclear Information System (INIS)

Rodovsky, T.J.

2006-01-01

This report presents the final hazard categorization (FHC) for the remediation of the 118-D-1, 118-D-2, and 118-D-3 Burial Grounds located within the 100-D/DR Area of the Hanford Site and the 118-H-1, 118-H-2, and 118-H-3 Burial Grounds located within the 100-H Area of the Hanford Site

Final Hazard Categorization for the Remediation of the 118-D-1, 118-D-2, 118-D-3, 118-H-1, 118-H-2, and 118-H-3 Solid Waste Burial Grounds

Energy Technology Data Exchange (ETDEWEB)

T. J. Rodovsky

2006-12-06

This report presents the final hazard categorization (FHC) for the remediation of the 118-D-1, 118-D-2, and 118-D-3 Burial Grounds located within the 100-D/DR Area of the Hanford Site and the 118-H-1, 118-H-2, and 118-H-3 Burial Grounds located within the 100-H Area of the Hanford Site.

Final Hazard Categorization for the Remediation of the 118-D-1, 118-D-2, 118-D-3, 118-H-1, 118-H-2, and 118-H-3 Solid Waste Burial Grounds

Energy Technology Data Exchange (ETDEWEB)

T. J. Rodovsky

2007-04-12

This report presents the final hazard categorization (FHC) for the remediation of the 118-D-1, 118-D-2, and 118-D-3 Burial Grounds located within the 100-D/DR Area of the Hanford Site and the 118-H-1, 118-H-2, and 118-H-3 Burial Grounds located within the 100-H Area of the Hanford Site.

Final Hazard Categorization for the Remediation of the 118-D-1, 118-D-2, 118-D-3, 118-H-1, 118-H-2, and 118-H-3 Solid Waste Burial Grounds

International Nuclear Information System (INIS)

TRodovsky, T.J.

2007-01-01

This report presents the final hazard categorization (FHC) for the remediation of the 118-D-1, 118-D-2, and 118-D-3 Burial Grounds located within the 100-D/DR Area of the Hanford Site and the 118-H-1, 118-H-2, and 118-H-3 Burial Grounds located within the 100-H Area of the Hanford Site

Safety analysis of the Chernobyl accident origin decontamination waste burials in Belarus

International Nuclear Information System (INIS)

Skurat, V.V.; Shiryaeva, N.M.; Myshkina, N.K.; Gvozdev, A.A.; Serebryanyj, G.Z.; Golikova, N.B.

2002-01-01

Potential dangerous of the decontamination waste burials was estimated by means of the generalized multicompartmental model. Characteristics of 24 the most large and unfavorable decontamination waste burials are shown and an estimate of their safety is given. The burial effect zones were determined (100-300 m). A reliability of the forecasting estimate of potential dangerous radioactive contamination of ground waters near the burials was checked on example of the Dudichi decontamination waste burial

Decommissioning of commercial shallow-land burial sites

International Nuclear Information System (INIS)

Murphy, E.S.; Holter, G.M.

1979-01-01

Estimated costs and safety considerations for decommissioning LLW burial grounds have been evaluated. Calculations are based on a generic burial ground assumed to be located at a western and an eastern site. Decommissioning modes include: (1) site stabilization followed by long-term care of the site; and (2) waste relocation. Site stabilization is estimated to cost from $0.4 million to $7.5 million, depending on the site and the stabilization option chosen. Long-term care is estimated to cost about $100,000 annually, with somewhat higher costs during early years because of increased site maintenance and environmental monitoring requirements. Long-term care is required until the site is released for unrestricted public use. Occupational and public safety impacts of site stabilization and long-term care are estimated to be small. Relocation of all the waste from a reference burial ground is estimated to cost more than $1.4 billion and to require more than 20 years for completion. Over 90% of the cost is associated with packaging, transportation, and offsite disposal of the exhumed waste. Waste relocation results in significant radiation exposure to decommissioning workers

RCRA closure plan for the Bear Creek Burial Grounds B Area and Walk-In Pits at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1992-11-01

The Bear Creek Burial Grounds (BCBG) are located on the southwest flank of Pine Ridge ∼1.5 miles west of the Oak Ridge Y-12 Plant in Bear Creek Valley. This facility consists of several contiguous disposal sites identified as Burial Grounds A, B, C, and D. Each burial site consists of a series of trenches used for disposal of solid wastes and, in some cases, liquid wastes. Initially, the RCRA Closure/Postclosure plan for the BCBG was intended to apply to A Area, C-West, B Area, and the walk-in pits for BCBG. However, a plan was provided to include the B Area in the walk-in pits so that both areas cold be closed under one cap. The closure plan for B Area and the walk-in pits is presented in this document. The actual quantity and identity of materials is uncertain. The largest volume of material disposed in BCBG consists of uranium-contaminated industrial trash (paper, wood, steel, glass, and rubble)

Chronology of the 1st–2nd Century Graves from the Tarasovo Burial Ground

Directory of Open Access Journals (Sweden)

Goldina Rimma D.

2016-03-01

Full Text Available The article focuses on the chronology of graves dating back to the early (1st – 2nd centuries AD – Nyrgynda stage of the 1st – 5th century Tarasovo burial ground, a classical monument attributed to the Cheganda culture of the Pyany Bor cultural-historical community. Cultural stratigraphy is applied as a research method. Artifacts from the early stage were correlated for 37 male and 102 female complexes, separately. The analysis of grave goods from male burials showed the following three chronological groups, that can be distinguished at the Nyrgynda stage: 1st century (group 1, 2nd century (group 2 and 1st – 2nd centuries AD (group 3. The goods from female graves are more representative and various, so three more groups with shorter chronological lives can be singled out: the fi rst half of the 2nd century (group 2а, the second half of the 2nd century (group 2б and the 1st – fi rst half of the 2nd century (group 4. Certainly, the suggested chronology leaves room for any eventual corrections subject to new findings.

Integration of CERCLA and RCRA requirements at the Radioactive Waste Burial Grounds, Savannah River Site, Aiken, South Carolina

International Nuclear Information System (INIS)

Hoffman, W.D.; Wyatt, D.E.

1992-01-01

The purpose of this paper to is present the comprehensive approach being taken at the Savannah River Site (SRS) to consolidate regulatory documents, characterization and assessment activities for 3 contiguous waste management facilities. These facilities cover 7.12 x 10 5 m 2 (194 acres) and include an Old Radioactive Waste Burial Ground, a Low Level Radioactive Waste Disposal Facility, and a closed Mixed Waste Management Facility. Each of these facilities include one or more operable units including solvent tanks, transuranic waste storage pads, research lysimeters and experimental confinement disposal vaults. All of these facilities have differing submittal dates for regulatory documents but similar and continuous environmental problems. The characterization and risk assessment require simultaneous efforts for all facilities to adequately define the nature and extent of past, present and future environmental impact. Current data indicates that contaminant plumes in both soil and water are comingled, interspersed and possibly exist internally within the contiguous facilities, requiring a combined investigative effort. This paper describes the combination of regulatory documents leading to this comprehensive and integrative approach for burial ground characterization at the Savannah River Site

DOE program for improvement practices for shallow burial of radioactive waste

International Nuclear Information System (INIS)

Dieckhoner, J.E.

1978-01-01

The practice of burying solid radioactive waste in relatively shallow pits or trenches at government nuclear sites dates back to the Manhattan Project. In some cases, where local conditions were considered unfavorable, intersite shipment of waste has been required. This general concept was later used at commercially-operated sites under Federal or state regulation. The purpose, scope, and results of a DOE program begun several years ago for improvements of burial ground disposal methods are reviewed. The program includes the re-evaluation of the original siting and of operating practices at existing burial grounds (including monitoring for migration of activity); the development of improved criteria for siting of new grounds that might be required as the defense site operations continue; and development of corrective measures such as diking and better draining for possible unsatisfactory conditions that might be detected. The possible applications of these findings to commercial burial grounds is discussed

Annual Status Report (FY2015) Performance Assessment for the Disposal of Low-Level Waste in the 200 West Area Burial Grounds

Energy Technology Data Exchange (ETDEWEB)

Khaleel, R. [INTERA, Inc., Austin, TX (United States); Mehta, S. [CH2M Hill Plateau Remediation Company, Richland, WA (United States); Nichols, W. E. [CH2M Hill Plateau Remediation Company, Richland, WA (United States)

2016-02-01

This annual review provides the projected dose estimates of radionuclide inventories disposed in the active 200 West Area Low-Level Burial Grounds (LLBGs) since September 26, 1988. These estimates area calculated using the original does methodology developed in the performance assessment (PA) analysis (WHC-EP-0645).

NRC Task Force report on review of the federal/state program for regulation of commercial low-level radioactive waste burial grounds

International Nuclear Information System (INIS)

1977-01-01

The underlying issue explored in this report is that of Federal vs State regulation of commercial radioactive waste burial grounds. The need for research and development, a comprehensive set of standards and criteria, a national plan for low-level waste management, and perpetual care funding are closely related to the central issue and are also discussed. Five of the six commercial burial grounds are regulated by Agreement States; the sixth is regulated solely by the NRC (NRC also regulates Special Nuclear Material at the sites). The sites are operated commercially. The operators contribute to the perpetual care funds for the sites at varying rates. The States have commitments for the perpetual care of the decommissioned sites except for one site, located on Federally owned land. Three conclusions are reached. Federal control over the disposal of low-level waste should be increased by requiring joint Federal/State site approval, NRC licensing, Federal ownership of the land, and a Federally administered perpetual care program. The NRC should accelerate the development of its regulatory program for the disposal of low-level waste. The undisciplined proliferation of low-level burial sites must be avoided. NRC should evaluate alternative disposal methods, conduct necessary studies, and develop a comprehensive low-level waste regulatory program (i.e., accomplish the above recommendations) prior to the licensing of new disposal sites

MCNP Modeling Results for Location of Buried TRU Waste Drums

International Nuclear Information System (INIS)

Steinman, D K; Schweitzer, J S

2006-01-01

In the 1960's, fifty-five gallon drums of TRU waste were buried in shallow pits on remote U.S. Government facilities such as the Idaho National Engineering Laboratory (now split into the Idaho National Laboratory and the Idaho Completion Project [ICP]). Subsequently, it was decided to remove the drums and the material that was in them from the burial pits and send the material to the Waste Isolation Pilot Plant in New Mexico. Several technologies have been tried to locate the drums non-intrusively with enough precision to minimize the chance for material to be spread into the environment. One of these technologies is the placement of steel probe holes in the pits into which wireline logging probes can be lowered to measure properties and concentrations of material surrounding the probe holes for evidence of TRU material. There is also a concern that large quantities of volatile organic compounds (VOC) are also present that would contaminate the environment during removal. In 2001, the Idaho National Engineering and Environmental Laboratory (INEEL) built two pulsed neutron wireline logging tools to measure TRU and VOC around the probe holes. The tools are the Prompt Fission Neutron (PFN) and the Pulsed Neutron Gamma (PNG), respectively. They were tested experimentally in surrogate test holes in 2003. The work reported here estimates the performance of the tools using Monte-Carlo modelling prior to field deployment. A MCNP model was constructed by INEEL personnel. It was modified by the authors to assess the ability of the tools to predict quantitatively the position and concentration of TRU and VOC materials disposed around the probe holes. The model was used to simulate the tools scanning the probe holes vertically in five centimetre increments. A drum was included in the model that could be placed near the probe hole and at other locations out to forty-five centimetres from the probe-hole in five centimetre increments. Scans were performed with no chlorine in the

Hanford Site Transuranic (TRU) Waste Certification Plan

International Nuclear Information System (INIS)

GREAGER, T.M.

2000-01-01

As a generator of transuranic (TRU) and TRU mixed waste destined for disposal at the Waste Isolation Pilot Plant (WIPP), the Hanford Site must ensure that its TRU waste meets the requirements of US. Department of Energy (DOE) 0 435.1, ''Radioactive Waste Management,'' and the Contact-Handled (CH) Transuranic Waste Acceptance Criteria for the Waste Isolation Pilot Plant (WIPP-WAC). WIPP-WAC requirements are derived from the WIPP Technical Safety Requirements, WIPP Safety Analysis Report, TRUPACT-II SARP, WIPP Land Withdrawal Act, WIPP Hazardous Waste Facility Permit, and Title 40 Code of Federal Regulations (CFR) 191/194 Compliance Certification Decision. The WIPP-WAC establishes the specific physical, chemical, radiological, and packaging criteria for acceptance of defense TRU waste shipments at WIPP. The WPP-WAC also requires that participating DOE TRU waste generator/treatment/storage sites produce site-specific documents, including a certification plan, that describe their program for managing TRU waste and TRU waste shipments before transferring waste to WIPP. Waste characterization activities provide much of the data upon which certification decisions are based. Waste characterization requirements for TRU waste and TRU mixed waste that contains constituents regulated under the Resource Conservation and Recovery Act (RCRA) are established in the WIPP Hazardous Waste Facility Permit Waste Analysis Plan (WAP). The Hanford Site Quality Assurance Project Plan (QAPjP) (HNF-2599) implements the applicable requirements in the WAP and includes the qualitative and quantitative criteria for making hazardous waste determinations. The Hanford Site must also ensure that its TRU waste destined for disposal at WPP meets requirements for transport in the Transuranic Package Transporter-11 (TRUPACT-11). The US. Nuclear Regulatory Commission (NRC) establishes the TRUPACT-11 requirements in the Safety Analysis Report for the TRUPACT-II Shipping Package (TRUPACT-11 SARP). In

Long-term sequential monitoring of controlled graves representing common burial scenarios with ground penetrating radar: Years 2 and 3

Science.gov (United States)

Schultz, John J.; Walter, Brittany S.; Healy, Carrie

2016-09-01

Geophysical techniques such as ground-penetrating radar (GPR) have been successfully used for forensic searches to locate clandestine graves and physical evidence. However, additional controlled research is needed to fully understand the applicability of this technology when searching for clandestine graves in various environments, soil types, and for longer periods of time post-burial. The purpose of this study was to determine the applicability of GPR for detecting controlled graves in a Spodosol representing multiple burial scenarios for Years 2 and 3 of a three-year monitoring period. Objectives included determining how different burial scenarios are factors in producing a distinctive anomalous response; determining how different GPR imagery options (2D reflection profiles and horizontal time slices) can provide increased visibility of the burials; and comparing GPR imagery between 500 MHz and 250 MHz dominant frequency antennae. The research site contained a grid with eight graves representing common forensic burial scenarios in a Spodosol, a common soil type of Florida, with six graves containing a pig carcass (Sus scrofa). Burial scenarios with grave items (a deep grave with a layer of rocks over the carcass and a carcass wrapped in a tarpaulin) produced a more distinctive response with clearer target reflections over the duration of the monitoring period compared to naked carcasses. Months with increased precipitation were also found to produce clearer target reflections than drier months, particularly during Year 3 when many grave scenarios that were not previously visible became visible after increased seasonal rainfall. Overall, the 250 MHz dominant frequency antenna imagery was more favorable than the 500 MHz. While detection of a simulated grave may be difficult to detect over time, long term detection of a grave in a Spodosol may be possible if the disturbed spodic horizon is detected. Furthermore, while grave visibility increased with the 2D

RH-TRU Waste Content Codes

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions

2007-07-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: • A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. • A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is “3.” The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

Development of a safe TRU transportation system (STRUTS) for DOE's TRU waste

International Nuclear Information System (INIS)

Edling, D.A.; Hopkins, D.R.; Walls, H.C.

1978-01-01

Transportation, the link between TRU waste generation and WIPP (Waste Isolation Pilot Project) and a vital link in the overall TRU waste management program, must be addressed. The program must have many facets: ensuring public and carrier acceptance, formation of a functional and current transportation data base, systems integration, maximum utilization of existing technology, and effective implementation and integration of the transport system into current and planned operational systems

Final Hazard Categorization and Auditable Safety Analysis for the Remediation of the 118-D-1, 118-D-2, 118-D-3, 118-H-1, 118-H-2 and 118-H-3 Solid Waste Burial Grounds

Energy Technology Data Exchange (ETDEWEB)

T. J. Rodovsky

2006-03-01

This report presents the initial hazard categorization, final hazard categorization and auditable safety analysis for the remediation of the 118-D-1, 118-D-2, and 118-D-3 Burial Grounds located within the 100-D/DR Area of the Hanford Site and the 118-H-1, 118-H-2, and 118-H-3 Burial Grounds located within the 100-H Area of the Hanford Site.

Groundwater monitoring in the Savannah River Plant low-level waste burial ground: a summary and interpretation of the analytical data

International Nuclear Information System (INIS)

Ryan, J.P.

1983-01-01

This document describes chemical mechanisms that may affect trace-level radionuclide migration through acidic sandy clay soils in a humid environment, and summarizes the extensive chemical and radiochemical analyses of the groundwater directly below the SRP Low-Level Waste (LLW) Burial Ground (643-G). Anomalies were identified in the chemistry of individual wells which appear to be related to small amounts of fission product activity that have reached the water table. The chemical properties which were statistically related to trace-level transport of Cs-137 and Sr-90 were iron, potassium, sodium and calcium. Concentrations on the order of 100 ppM appear sufficient to affect nuclide migration. Several complexation mechanisms for plutonium migration were investigated, but most of these were shown to be incapable of mobilizing more than trace quantities of plutonium. The parameters of greatest importance were oxidation-reduction potential, pH, dissolved organic carbon, phosphate and carbonate. Of these, organic and phosphate complexation had the greatest potential for mobilizing plutonium in the SRP groundwater. In the absence of such complexants, plutonium would be essentially immobile in the soil/water system of the SRP burial ground. 50 references, 8 figures, 2 tables

Limits for the burial of the Department of Energy transuranic wastes

Energy Technology Data Exchange (ETDEWEB)

Healy, J.W.; Rodgers, J.C.

1979-01-15

Potential limits for the shallow earth burial of transuranic elements were examined by simplified models of the individual pathways to man. Pathways examined included transport to surface steams, transport to ground water, intrusion, and people living on the burial ground area after the wastes have surfaced. Limits are derived for each pathway and operational limits are suggested based upon a dose to the organ receiving the maximum dose rate of 0.5 rem/y after 70 years of exposure for the maximum exposed individual.

Limits for the burial of the Department of Energy transuranic wastes

International Nuclear Information System (INIS)

Healy, J.W.; Rodgers, J.C.

1979-01-01

Potential limits for the shallow earth burial of transuranic elements were examined by simplified models of the individual pathways to man. Pathways examined included transport to surface steams, transport to ground water, intrusion, and people living on the burial ground area after the wastes have surfaced. Limits are derived for each pathway and operational limits are suggested based upon a dose to the organ receiving the maximum dose rate of 0.5 rem/y after 70 years of exposure for the maximum exposed individual

Status of ERDA TRU waste packaging study

International Nuclear Information System (INIS)

Doty, J.W. Jr.

1977-01-01

This paper discusses the status of Task 3 of the TRU Waste Cyclone Drum Incinerator and Treatment System program. This task covers acceptable TRU packaging for interim storage and terminal isolation. The kind of TRU wastes generated by contractors and its transport are discussed. Both drum and box systems are desirable

Development of waste packages for TRU-disposal. 5. Development of cylindrical metal package for TRU wastes

International Nuclear Information System (INIS)

Mine, Tatsuya; Mizubayashi, Hiroshi; Asano, Hidekazu; Owada, Hitoshi; Otsuki, Akiyoshi

2005-01-01

Development of the TRU waste package for hulls and endpieces compression canisters, which include long-lived and low sorption nuclides like C-14 is essential and will contribute a lot to a reasonable enhancement of safety and economy of the TRU-disposal system. The cylindrical metal package made of carbon steel for canisters to enhance the efficiency of the TRU-disposal system and to economically improve their stacking conditions was developed. The package is a welded cylindrical construction with a deep drawn upper cover and a disc plate for a bottom cover. Since the welding is mainly made only for an upper cover and a bottom disc plate, this package has a better containment performance for radioactive nuclide and can reduce the cost for construction and manufacturing including its welding control. Furthermore, this package can be laid down in pile for stacking in the circular cross section disposal tunnel for the sedimentary rock, which can drastically minimize the space for disposal tunnel as mentioned previously in TRU report. This paper reports the results of the study for application of newly developed metal package into the previous TRU-disposal system and for the stacking equipment for the package. (author)

DOE's plan for buried transuranic (TRU) contaminated waste

International Nuclear Information System (INIS)

Mathur, J.; D'Ambrosia, J.; Sease, J.

1987-01-01

Prior to 1970, TRU-contaminated waste was buried as low-level radioactive waste. In the Defense Waste Management Plan issued in 1983, the plan for this buried TRU-contaminated waste was to monitor the buried waste, take remedial actions, and to periodically evaluate the safety of the waste. In March 1986, the General Accounting Office (GAO) recommended that the Department of Energy (DOE) provide specific plans and cost estimates related to buried TRU-contaminated waste. This plan is in direct response to the GAO request. Buried TRU-contaminated waste and TRU-contaminated soil are located in numerous inactive disposal units at five DOE sites. The total volume of this material is estimated to be about 300,000 to 500,000 m 3 . The DOE plan for TRU-contaminated buried waste and TRU-contaminated soil is to characterize the disposal units; assess the potential impacts from the waste on workers, the surrounding population, and the environment; evaluate the need for remedial actions; assess the remedial action alternatives; and implement and verify the remedial actions as appropriate. Cost estimates for remedial actions for the buried TRU-contaminated waste are highly uncertain, but they range from several hundred million to the order of $10 billion

Characterization optimization for the National TRU waste system

International Nuclear Information System (INIS)

Basabilvazo, George T.; Countiss, S.; Moody, D.C.; Jennings, S.G.; Lott, S.A.

2002-01-01

On March 26, 1999, the Waste Isolation Pilot Plant (WIPP) received its first shipment of transuranic (TRU) waste. On November 26, 1999, the Hazardous Waste Facility Permit (HWFP) to receive mixed TRU waste at WIPP became effective. Having achieved these two milestones, facilitating and supporting the characterization, transportation, and disposal of TRU waste became the major challenges for the National TRU Waste Program. Significant challenges still remain in the scientific, engineering, regulatory, and political areas that need to be addressed. The National TRU Waste System Optimization Project has been established to identify, develop, and implement cost-effective system optimization strategies that address those significant challenges. Fundamental to these challenges is the balancing and prioritization of potential regulatory changes with potential technological solutions. This paper describes some of the efforts to optimize (to make as functional as possible) characterization activities for TRU waste.

Estimation of the release and migration of nickel through soils and groundwater at the Hanford Site 218-E-12B Burial Ground

International Nuclear Information System (INIS)

Rhoads, K.; Bjornstad, B.N.; Lewis, R.E.

1994-05-01

An assessment was performed to evaluate release and transport of nickel from large metal components containing nickel-bearing alloys at the Hanford Site 218-E-12B Burial Ground. The potential for nickel within the components to enter groundwater under the burial site was investigated by examining available data on the site's geology, geochemistry, and geohydrology to develop a conceptual model for release and transport of nickel from the components. In addition, laboratory studies were performed to provide information needed for the model, but which was not available from existing databases. Estimates of future concentrations of nickel radioisotopes ( 59 Ni and 63 Ni) and total elemental nickel in the unconfined aquifer and in the Columbia River were developed based on this information

Studies of Pre-Mongol Bulgar Burials in the Territory of the Astrakhan Oblast

Directory of Open Access Journals (Sweden)

Kutukov Dmitriy V.

2013-09-01

Full Text Available The funeral ceremonial features traced in three Bulgar burials, which have been discovered during archaeological excavations on the burial grounds named "Shchuchii", "Posol’skii" and "Kovyl’nyi" (Astrakhan oblast, are discussed in the article. The burials are dated, respectively, to the early 10th century, the early 9th century, and the late 8th – early 9th centuries. The funeral gifts include mainly ceramic vessels. The "Posol’skii" burial site also yielded jewelry and weapon fragments (bow plates. In two burials ("Posol’skii" and "Kovyl’nyi", sheep bones were recorded. The burials apparently reflect the process of the Bulgars settling in the southern direction to the Lower Volga river area, up to its deltaic part

A summary of ecological investigations at the burial ground complex, Savannah River Site - 1994

Energy Technology Data Exchange (ETDEWEB)

Friday, G.P.; Hartman, G.D.; Mackey, H.E. Jr.; Riley, R.S.; Roach, J.L.; Specht, W.L.; Westbury, H.M.; Wike, L.D.

1994-11-01

This report summarizes the results of three ecological investigations that were conducted in 1994 at the Burial Ground Complex (BGC) at the Savannah River Site (SRS). The three topics of study included remote sensing, aquatic toxicity testing, and qualitative surveys of herpetofauna and small mammals. Interim reports from each investigation are included in the appendices (A, B, and C). The objectives of the remote sensing effort were to compile historical aerial photography of the BGC and to develop a land use/cover map of the complex using recent aerial imagery. The goal of the aquatic toxicity testing was to determine if surface waters were toxic to aquatic biota whereas the objectives of the vertebrate surveys were to identify the species diversity and relative abundances of amphibians, reptiles, and small mammals inhabiting the study area.

A summary of ecological investigations at the burial ground complex, Savannah River Site - 1994

International Nuclear Information System (INIS)

Friday, G.P.; Hartman, G.D.; Mackey, H.E. Jr.; Riley, R.S.; Roach, J.L.; Specht, W.L.; Westbury, H.M.; Wike, L.D.

1994-11-01

This report summarizes the results of three ecological investigations that were conducted in 1994 at the Burial Ground Complex (BGC) at the Savannah River Site (SRS). The three topics of study included remote sensing, aquatic toxicity testing, and qualitative surveys of herpetofauna and small mammals. Interim reports from each investigation are included in the appendices (A, B, and C). The objectives of the remote sensing effort were to compile historical aerial photography of the BGC and to develop a land use/cover map of the complex using recent aerial imagery. The goal of the aquatic toxicity testing was to determine if surface waters were toxic to aquatic biota whereas the objectives of the vertebrate surveys were to identify the species diversity and relative abundances of amphibians, reptiles, and small mammals inhabiting the study area

TRU waste transportation -- The flammable gas generation problem

International Nuclear Information System (INIS)

Connolly, M.J.; Kosiewicz, S.T.

1997-01-01

The Nuclear Regulatory Commission (NRC) has imposed a flammable gas (i.e., hydrogen) concentration limit of 5% by volume on transuranic (TRU) waste containers to be shipped using the TRUPACT-II transporter. This concentration is the lower explosive limit (LEL) in air. This was done to minimize the potential for loss of containment during a hypothetical 60 day period. The amount of transuranic radionuclide that is permissible for shipment in TRU waste containers has been tabulated in the TRUPACT-II Safety Analysis Report for Packaging (SARP, 1) to conservatively prevent accumulation of hydrogen above this 5% limit. Based on the SARP limitations, approximately 35% of the TRU waste stored at the Idaho National Engineering and Environmental Lab (INEEL), Los Alamos National Lab (LANL), and Rocky Flats Environmental Technology Site (RFETS) cannot be shipped in the TRUPACT-II. An even larger percentage of the TRU waste drums at the Savannah River Site (SRS) cannot be shipped because of the much higher wattage loadings of TRU waste drums in that site's inventory. This paper presents an overview of an integrated, experimental program that has been initiated to increase the shippable portion of the Department of Energy (DOE) TRU waste inventory. In addition, the authors will estimate the anticipated expansion of the shippable portion of the inventory and associated cost savings. Such projection should provide the TRU waste generating sites a basis for developing their TRU waste workoff strategies within their Ten Year Plan budget horizons

Subsurface Planar Vitrification Treatment of Problematic TRU Wastes: Status of a Technology Demonstration Program

International Nuclear Information System (INIS)

Morse, M.K.; Nowack, B.R.; Thompson, L.E.

2006-01-01

This paper provides a status of the In Situ Transuranic Waste Delineation and Removal Project in which the GeoMelt R Subsurface Planar Vitrification TM (SPV TM ) process is being evaluated for the in situ treatment of burial sites containing remote handled mixed transuranic (TRU) waste. The GeoMelt R SPV TM process was invented and patented by Geosafe Corporation. AMEC holds the exclusive worldwide license to use this technology. The current project is part of a three-phase demonstration program to evaluate the effectiveness of the GeoMelt R SPV TM process to treat waste contained in vertical pipe units (VPUs) and caissons that were used for the disposal of remote handled transuranic wastes located at Hanford's 618-10 and 618-11 burial grounds. This project is being performed for the US Department of Energy (DOE) for use at the Hanford site and other DOE installations. The Phase I evaluation determined that removal and treatment of the 618-10/11 VPUs are beyond what can be safely accomplished using conventional excavation methods. Accordingly, a careful stepwise non-intrusive delineation approach and treatment using the GeoMelt R SPV TM technology, followed by removal, characterization, and disposal of the resulting inert vitrified mass was identified as the preferred alternative. Phase II of the project, which started in July 2004, included a full-scale non-radioactive demonstration of AMEC's GeoMelt R SPV TM process on a mock VPU configured to match the actual VPUs. The non-radioactive demonstration (completed in May 2005) was performed to confirm the approach and design before proceeding to a radioactive ('hot') demonstration on an actual VPU. This demonstration took approximately 130 hours, processed the entire mock VPU, and resulted in a vitrified monolith weighing an estimated 90 tonnes. [1] Plans for a radioactive demonstration on an actual VPU are being developed for CY 2006. In addition to demonstrating GeoMelt R SPV TM , delineation techniques are being

Enhancing TRU burning and Am transmutation in Advanced Recycling Reactor

International Nuclear Information System (INIS)

Ikeda, Kazumi; Kochendarfer, Richard A.; Moriwaki, Hiroyuki; Kunishima, Shigeru

2011-01-01

Research highlights: → This ARR is an oxide fueled sodium cooled reactor based on innovative technologies to destruct TRU. → TRU burning core is designed to burn TRU at 28 kg/TW th h, adding moderator pins of B 4 C (Enriched B-11). → Am transmutation core can transmute Am at 34 kg/TW th h, adding uranium free AmN blanket to TRU burning core. → The TRU burning core improves TRU burning by 40-50% than the previous core. → The Am transmutation core can transmute Am effectively, keeping the void reactivity acceptable. - Abstract: This paper presents about conceptual designs of Advanced Recycling Reactor (ARR) focusing on enhancement in transuranics (TRU) burning and americium (Am) transmutation. The design has been conducted in the context of the Global Nuclear Energy Partnership (GNEP) seeking to close nuclear fuel cycle in ways that reduce proliferation risks, reduce the nuclear waste in the US and further improve global energy security. This study strives to enhance the TRU burning and the Am transmutation, assuming the development of related technologies in this study, while the ARR based on mature technologies was designed in the previous study. It has followed that the provided TRU burning core is designed to burn TRU at 28 kg/TW th h, by adding moderator pins of B 4 C (Enriched B-11) and the Am transmutation core will be able to transmute Am at 34 kg/TW th h, by locating Am blanket of AmN around the TRU burning core. It indicates that these concepts improve TRU burning by 40-50% than the previous core and can transmute Am effectively, keeping the void reactivity acceptable.

Grout testing and characterization for shallow-land burial trenches at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Tallent, O.K.; Sams, T.L.; Tamura, T.; Godsey, T.T.; Francis, C.L.; McDaniel, E.W.

1986-10-01

An investigation was conducted to develop grout formulations suitable for in situ stabilization of low-level and transuranic (TRU) waste in shallow-land burial trenches at Idaho National Engineering Laboratory (INEL). The acceptabilities of soil, ordinary particulate, and fine particulate grouts were evaluated based on phase separation, compressive strength, freeze/thaw, penetration resistance, rheological, water permeability, column, and other tests. Soil grouts with soil-to-cement weight ratios from 0.91 to 1.60 were found to be suitable for open trench or drum disposal. Ordinary particulate grouts containing type I,II Portland cement, class C fly ash, bentonite, water, and a fluidizer were formulated to fill large voids within the soil/waste matrix of a closed shallow-land burial trench. Fine particulate grouts containing fine (mean particle size, 9.6 m) cement and water were formulated to fill smaller voids and to establish a grout-soil barrier to prevent water intrusion into the grouted waste trench. Solution, or chemical grouts, were evaluated as possible substitutes for the fine particulate grouts

RH-TRU Waste Content Codes (RH-Trucon)

International Nuclear Information System (INIS)

2007-01-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is '3.' The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR limits based

RH-TRU Waste Content Codes (RH-TRUCON)

International Nuclear Information System (INIS)

2007-01-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is '3.' The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR limits based

RH-TRU Waste Content Codes (RH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-08-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: • A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. • A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is “3.” The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

RH-TRU Waste Content Codes (RH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions

2007-05-30

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: • A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. • A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is “3.” The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

IMPROVEMENTS IN CONTAINER MANAGEMENT OF TRANSURANIC (TRU) AND LOW LEVEL RADIOACTIVE WASTE STORED AT THE CENTRAL WASTE COMPLEX (CWC) AT HANFORD

International Nuclear Information System (INIS)

UYTIOCO EM

2007-01-01

The Central Waste Complex (CWC) is the interim storage facility for Resource Conservation and Recovery Act (RCRA) mixed waste, transuranic waste, transuranic mixed waste, low-level and low-level mixed radioactive waste at the Department of Energy's (DOE'S) Hanford Site. The majority of the waste stored at the facility is retrieved from the low-level burial grounds in the 200 West Area at the Site, with minor quantities of newly generated waste from on-site and off-site waste generators. The CWC comprises 18 storage buildings that house 13,000 containers. Each waste container within the facility is scanned into its location by building, module, tier and position and the information is stored in a site-wide database. As waste is retrieved from the burial grounds, a preliminary non-destructive assay is performed to determine if the waste is transuranic (TRU) or low-level waste (LLW) and subsequently shipped to the CWC. In general, the TRU and LLW waste containers are stored in separate locations within the CWC, but the final disposition of each waste container is not known upon receipt. The final disposition of each waste container is determined by the appropriate program as process knowledge is applied and characterization data becomes available. Waste containers are stored within the CWC based on their physical chemical and radiological hazards. Further segregation within each building is done by container size (55-gallon, 85-gallon, Standard Waste Box) and waste stream. Due to this waste storage scheme, assembling waste containers for shipment out of the CWC has been time consuming and labor intensive. Qualitatively, the ratio of containers moved to containers in the outgoing shipment has been excessively high, which correlates to additional worker exposure, shipment delays, and operational inefficiencies. These inefficiencies impacted the LLW Program's ability to meet commitments established by the Tri-Party Agreement, an agreement between the State of Washington

Performance Assessment Monitoring Plan for the Hanford Site Low-Level Waste Burial Grounds

International Nuclear Information System (INIS)

SONNICHSEN, J.C.

2000-01-01

As directed by the U.S. Department of Energy (DOE), Richland Operations Office (DOE-RL), Fluor Hanford, Inc. will implement the requirements of DOE Order 435.1, Radioactive Waste Management, as the requirements relate to the continued operation of the low-level waste disposal facilities on the Hanford Site. DOE Order 435.1 requires a disposal authorization statement authorizing operation (or continued operation) of a low-level waste disposal facility. The objective of this Order is to ensure that all DOE radioactive waste is managed in a manner that protects the environment and personnel and public health and safety. The manual (DOE Order 435.1 Manual) implementing the Order states that a disposal authorization statement shall be issued based on a review of the facility's performance assessment and composite analysis or appropriate Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) of 1980 documentation. The disposal authorization shall specify the limits and conditions on construction, design, operations, and closure of the low-level waste facility. Failure to obtain a disposal authorization statement shall result in shutdown of an operational disposal facility. In fulfillment of the requirements of DOE Order 435.1, a disposal authorization statement was issued on October 25, 1999, authorizing the Hanford Site to transfer, receive, possess, and dispose of low-level radioactive waste at the 200 East Area and the 200 West Area Low-Level Burial Grounds. The disposal authorization statement constitutes approval of the performance assessment and composite analysis, authorizes operation of the facility, and includes conditions that the disposal facility must meet. One of the conditions is that monitoring plans for the 200 East Area and 200 West Area Low-Level Burial Grounds be written and approved by the DOE-RL. The monitoring plan is to be updated and implemented within 1 year following issuance of the disposal authorization statement to

Groundwater flow and tritium migration from the SRS Old Burial Ground to Fourmile Branch

International Nuclear Information System (INIS)

Flach, G.P.; Hamm, L.L.; Harris, M.K.

1996-04-01

The objectives of this investigation are twofold. The initial goal is to devise and demonstrate a technique for directly incorporating fine-scale lithologic data into heterogeneous hydraulic conductivity fields, for improved groundwater flow and contaminant transport model accuracy. The ultimate goal is to rigorously simulate past and future tritium migration from the SRS Old Burial Ground towards Fourmile Branch, to better understand the effects of various remediation alternatives such as no action and capping. Large-scale variability in hydraulic conductivity is usually the main influence on field-scale groundwater flow patterns and dispersive transport, following the relative locations of recharge and discharge areas. Incorporating realistic hydraulic conductivity heterogeneity into flow and transport models is paramount to accurate simulations, particularly for contaminant migration. Sediment lithologic descriptions and geophysical logs typically offer finer spatial resolution, and therefore more potential information about heterogeneity, than other site characterization data

Migration of radionuclides following shallow land burial

International Nuclear Information System (INIS)

Sedlet, J.; Golchert, N.W.

1980-01-01

A study of radionuclide migration was conducted at a facility used from 1944 to 1949 for the shallow land burial of radwaste produced during operations with two reactors and related nuclear research. It is situated in glacial drift 45 m thick. Underlying the drift is a generally level Silurian dolomite bedrock 60 m thick. The thickness of the drift decreases as the surface slopes downhill (north) until the dolomite reaches the surface and forms the bed of a river, 700 m to the north. This study was begun after tritiated water was detected in two picnic wells north of the facility, between the burial plot and the river. Surface and subsurface measurements indicate that tritium is migrating out of the burial site, but no other radionuclides have left the plot. The tritium concentrations decrease with distance from the plot. Tritium was found in the subsoil at all depths sampled, so the ground beneath and immediately around the plot contains tritium down to the dolomite aquifer. Time of travel of water from the burial plot to the nearest well is estimated to be 54 months. This would imply the peak concentration would reach the dolomite in about 35 years. By this time, 86% of the tritium would have disappeared by radioactive decay. The cyclical nature of the tritium content in the two wells implies that tritiated water is carried from the burial site by the spring rains when they recharge the groundwater supply

Beads from Inhumation Rite Burials of Gnezdovo Burial Mound

Directory of Open Access Journals (Sweden)

Dobrova Olga P.

2017-12-01

Full Text Available The beads from 33 inhumation burials at Gnezdovo burial mound are examined in the article. The beads (total 367 were crafted from stretched tube (258, stretched stick (3, winding (45, press molding (2 pcs., welding (2 pcs., and mosaic beads (9 pcs.. The burial mound contains virtually no broken beads, including the settlement's most common yellow glass beads. Besides glass beads, cornelian, crystal, amber and faience beads have been registered among the burial mound material, as well as beads crafted with metal. Apart from beads, grave inventories contained a series of pendants with a bead strung on a wire ring. The considered complexes contain five pendants of this type. Besides Gnezdovo, similar pendants have been discovered in Kiev, Timerev, Pskov and Vladimir barrows. A comparison between bead sets from Gnezdovo and Kiev burial mounds allows to conclude that the general composition and occurrence frequency of beads is identical for these burials. At the same time, beads crafted with rock crystal, cornelian and metal are more frequently discovered in Kiev inhumations.

Low-level burial grounds dangerous waste permit application

International Nuclear Information System (INIS)

1990-07-01

This document is submitted to request an exemption for Trench 94 from dangerous waste landfill liner and leachate collection and removal system (hereinafter referred to as liner/leachate system) requirements. This exemption request is based on an evaluation which demonstrates that burial in Trench 94 of cathodically protected submarine reactor compartments (SRC), which contain lead and polychlorinated biphenyls (PCB) as hazardous constituents, is as effective as disposal in a landfill having a liner/leachate system. This demonstration also considers the effectiveness of burial in Trench 94 in terms of preventing long-term migration of contaminants to groundwater or surface water. Modeling results indicate that release of contaminants to the groundwater or surface water will not occur until after long periods of time and that even after reaching the groundwater, contaminants will not be in excess of current regulatory limits, such as drinking water standards. Chapter 1.0 provides introductory information concerning this request, including the scope of the exemption request and relevant background information. The five subsequent chapters provide information needed to support the exemption request. Chapter 2.0 discusses the regulatory basis for the exemption request and presents performance objectives related to regulatory requirements. Chapter 3.0 provides a description of the site and its operation. Chapter 4.0 describes the wastes subject to this exemption request Chapter 5.0 discusses the performance of the disposal site with respect to performance objectives. Finally, Chapter 6.0 presents the actual request for exemption from requirements for a liner/leachate system. 30 refs., 13 figs., 6 tabs

An approach for the reasonable TRU waste management in NUCEF

International Nuclear Information System (INIS)

Mineo, H.; Dojiri, S.; Takeshita, I.; Tsujino, T.; Matsumura, T.; Nishizawa, I.; Sugikawa, S.

1995-01-01

The Nuclear Fuel Cycle Safety Engineering Research Facility (NUCEF) has started its hot operation at the beginning of 1995, where TRU (transuranic) elements are used. The management of TRU waste arisen in the facility is very important issue. Liquid and solid wastes containing TRU elements are generated mainly from the Fuel Treatment System for critical experiments and from the researches of reprocessing process and TRU waste management for reprocessing plants using hot cells and glove-boxes. The TRU waste management in NUCEF is based on the classification of waste, and is to maximize the recycle of reagents and the reuse of TRU elements separated from the waste, as well as to reduce the waste volume and to lower the risk of waste by advanced separation and solidification. In the future, the separation and solidification of TRU elements in the tanks of liquid waste, and the classification and discrimination of solid wastes, will be carried out applying the outcomes of the development by the researches in NUCEF. (authors)

Study on integrated TRU multi-recycling in sodium cooled fast reactor CDFR

International Nuclear Information System (INIS)

Hu Yun; Xu Mi; Wang Kan

2010-01-01

In view of recently proposed closed fuel cycle strategy which would recycle the integrated transuranics (TRU) from PWR spent fuel in the fast reactors, the neutronics characteristics of TRU recycled in China Demonstration Fast Reactor (CDFR) are studied in this paper. The results show that loading integrated TRU to substitute pure Pu as driver fuel will mainly make the influence on sodium void worth and negligible effects on other parameters, and hence TRU recycling in CDFR is feasible from viewpoint of core neutronics. If TRU is multi-recycled, the variation of TRU composition depends on fuel types and the ratio of TRU and U when recycling. It is indicated that, when TRU is multi-recycled in CDFR with MOX fuel, the minor actinides (MA) fraction in TRU will firstly decrease to ∼7.24% (minimum) within 8 TRU recycle times and then slowly increase to ∼7.7% after 20 TRU recycle times; while when TRU is multi-recycled in CDFR with metal fuel (TRU-U-10Zr), the MA fraction in TRU will gradually approach to an equilibrium state with the MA fraction of ∼3.8%, demonstrating better MA transmutation effect in metal fuel core. No matter 7.7 or 3.8%, they are both lower than ∼10% in PWR spent fuel with burnup of 45 GWd/tU, which presents satisfying effect of MA amount controlling for TRU multi-recycling strategy. On the other hand, the corresponding recycling parameters such as TRU heat release and neutron emission rate are also much lower in metal fuel than those in MOX fuel. Moreover, TRU recycled in metal fuel will bring greater fissile Pu isotopes equilibrium fraction due to better breeding capability of metal fuel. Finally, it could be summarized that integrated TRU multi-recycling in fast reactor can make contributions to both breeding and transmutation, and such strategy is a prospective closed fuel cycle manner to achieve the object of effective control of cumulated MA amount and sustainable development of nuclear energy.

Opisthorchiasis in infant remains from the medieval Zeleniy Yar burial ground of XII-XIII centuries AD

Directory of Open Access Journals (Sweden)

Sergey Mikhailovich Slepchenko

2015-01-01

Full Text Available We present a paleoparasitological analysis of the medieval Zeleniy Yar burial ground of the XII-XII centuries AD located in the northern part of Western Siberia. Parasite eggs, identified as eggs of Opisthorchis felineus, were found in the samples from the pelvic area of a one year old infant buried at the site. Presence of these eggs in the soil samples from the infant’s abdomen suggests that he/she was infected with opisthorchiasis and imply consumption of undercooked fish. Ethnographic records collected among the population of the northern part of Western Siberia reveal numerous cases of feeding raw fish to their children. Zeleniy Yar case of opisthorchiasis suggests that this dietary custom has persisted from at least medieval times.

RH-TRU Waste Content Codes (RH TRUCON)

International Nuclear Information System (INIS)

2007-01-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: (1) A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. (2) A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is ''3''. The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

RH-TRU Waste Content Codes (RH TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions

2007-05-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: • A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. • A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is “3.” The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

TRU waste form and package criteria meeting

Energy Technology Data Exchange (ETDEWEB)

None

1977-08-01

The broad subject of the meeting is the overall ERDA TRU waste management program, although the discussions also cover performance criteria for the Waste Isolation Pilot Plant and their implications for the overall TRU program. Separate abstracts were prepared for all ten presentations. (DLC)

RCRA closure plan for the Bear Creek Burial Grounds B Area and Walk- In Pits at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1993-01-01

In June 1987, the RCRA Closure/Postclosure Plan for the Bear Creek Burial Grounds (BCBG) was submitted to the Tennessee Department of Environment and Conservation (TDEC) for review and approval. TDEC modified and issued the plan approved on September 30, 1987. Subsequently, this plan was modified again and approved as Y/TS-395, Revised RCRA Closure Plan for the Bear Creek Burial Grounds (February 29, 1988). Y/TS-395 was initially intended to apply to A Area, C-West, B Area, and the Walk-In Pits of BCBG. However, a concept was developed to include the B Area (non-RCRA regulated) in the Walk-In Pits so that both areas would be closed under one cap. This approach included a tremendous amount of site preparation with an underlying stabilization base of 16 ft of sand for blast protection. The plan was presented to the state of Tennessee on March 8, 1990, and the Department of Energy was requested to review other unique alternatives to close the site. This amended closure plan goes further to include inspection and maintenance criteria along with other details

Transuranic (TRU) waste management at Savannah River - past, present and future

International Nuclear Information System (INIS)

D'Ambrosia, J.T.

1985-01-01

Defense TRU waste at Savannah River (SR) results from the Department of Energy's (DOE) national defense activities, including the operation of production reactors and fuel reprocessing plants and research and development activities. TRU waste is material declared as having negligible economic value, contaminated with alpha-emitting radionuclides of atomic number greater than 92, and half-lives longer than 20 years, in concentrations greater than 100 nCi/g. TRU waste has been retrievably stored at SR since 1974 awaiting disposal. The Waste Isolation Pilot Plant (WIPP), now under construction in New Mexico, is a research and development facility for demonstrating the safe disposal of defense TRU waste, including that in storage at SR. The major objective of the TRU program at SR is to support the TRU National Program, which is dedicated to preparing waste for, and emplacing waste in, the WIPP. Thus, the SR Program also supports WIPP operations. The SR Site specific goals are to phase out the indefinite storage of TRU waste, which has been the mode of waste management since 1974, and to dispose of SR's Defense TRU waste

TRU waste inventory collection and work-off plans for the centralization of TRU waste characterization at INL - on your mark - get set - 9410

International Nuclear Information System (INIS)

Mctaggert, Jerri Lynne; Lott, Sheila; Gadbury, Casey

2009-01-01

The U.S. Department of Energy (DOE) amended the Record of Decision (ROD) for the Waste Management Program: Treatment and Storage ofTransuranic Waste to centralize transuranic (TRU) waste characterization/certification from fourteen TRU waste sites. This centralization will allow for treatment, characterization and certification ofTRU waste from the fourteen sites, thirteen of which are sites with small quantities ofTRU waste, at the Idaho National Laboratory (INL) prior to shipping the waste to the Waste Isolation Pilot Plant (WIPP) for disposal. Centralization ofthis TRU waste will avoid the cost ofbuilding treatment, characterization, certification, and shipping capabilities at each ofthe small quantity sites that currently do not have existing facilities. Advanced Mixed Waste Treatment Project (AMWTP) and Idaho Nuclear Technology and Engineering Center (INTEC) will provide centralized shipping facilities, to WIPP, for all ofthe small quantity sites. Hanford, the one large quantity site identified in the ROD, has a large number ofwaste in containers that are overpacked into larger containers which are inefficient for shipment to and disposal at WIPP. The AMWTP at the INL will reduce the volume ofmuch of the CH waste and make it much more efficient to ship and dispose of at WIPP. In addition, the INTEC has a certified remote handled (RH) TRU waste characterization/certification program at INL to disposition TRU waste from the sites identified in the ROD.

Evidence of skeletal treponematosis from the medieval burial ground of St. Mary Spital, London, and implications for the origins of the disease in Europe.

Science.gov (United States)

Walker, Don; Powers, Natasha; Connell, Brian; Redfern, Rebecca

2015-01-01

Treponematosis is a syndrome of chronic infectious diseases. There has been much debate on its origins and spread, particularly with regard to venereal syphilis, an unsightly and debilitating disease in preantibiotic populations. The osteological analysis of 5,387 individuals excavated by Museum of London Archaeology from the medieval burial ground of St. Mary Spital in London (dated c 1120-1539) provided an unprecedented opportunity to investigate the nature and prevalence of disease over a period of time. Twenty-five individuals were found with suspected treponematosis, originating from all but the earliest period of the burial ground. Descriptions of affected individuals from each period, together with supporting images, are provided. In this work, particular emphasis was given to the distribution of lesions on the skeleton and the variation in patterns by sex and over time. Little change was observed in the distribution of bony change between individuals dated to pre- and post-Columbian periods. However, a dramatic rise in the prevalence of the disease in the final period (c 1400-1539) may reflect documentary reports of a European epidemic from the late 15th century. © 2014 Wiley Periodicals, Inc.

Taenia sp. in human burial from Kan River, East Siberia.

Science.gov (United States)

Slepchenko, Sergey Mikhailovich; Ivanov, Sergey Nikolaevich; Vybornov, Anton Vasilevich; Alekseevich, Tsybankov Alexander; Sergeyevich, Slavinsky Vyacheslav; Lysenko, Danil Nikolaevich; Matveev, Vyacheslav Evgenievich

2017-05-01

We present an arhaeoparasitological analysis of a unique burial from the Neftprovod II burial ground in East Siberia, which dated from the Bronze Age. Analysis of a sediment sample from the sacral region of the pelvis revealed the presence of Taenia sp. eggs. Because uncooked animal tissue is the primary source of Taenia, this indicated that the individual was likely consuming raw or undercooked meat of roe deer, red deer, or elk infected with Taenia. This finding represents the oldest case of a human infected with Taenia sp. from Eastern Siberia and Russia.

CH-TRU Waste Content Codes

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2008-01-16

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

Workplan/RCRA Facility Investigation/Remedial Investigation Report for the Old Radioactive Waste Burial Ground 643-E, S01-S22 - Volume I - Text and Volume II - Appendices

Energy Technology Data Exchange (ETDEWEB)

Conner, K.R.

2000-12-12

This document presents the assessment of environmental impacts resulting from releases of hazardous substances from the facilities in the Old Radioactive Waste Burial Ground 643-E, including Solvent Tanks 650-01E to 650-22E, also referred to as Solvent Tanks at the Savannah River Site, Aiken, South Carolina.

Plans for Managing Hanford Remote Handled Transuranic (TRU) Waste

International Nuclear Information System (INIS)

MCKENNEY, D.E.

2001-01-01

The current Hanford Site baseline and life-cycle waste forecast predicts that approximately 1,000 cubic meters of remote-handled transuranic (RH-TRU) waste will be generated by waste management and environmental restoration activities at Hanford. These 1,000 cubic meters, comprised of both transuranic and mixed transuranic (TRUM) waste, represent a significant portion of the total estimated inventory of RH-TRU to be disposed of at the Waste Isolation Pilot Plant (WIPP). A systems engineering approach is being followed to develop a disposition plan for each RH-TRU/TRUM waste stream at Hanford. A number of significant decision-making efforts are underway to develop and finalize these disposition plans, including: development and approval of a RH-TRU/TRUM Waste Project Management Plan, revision of the Hanford Waste Management Strategic Plan, the Hanford Site Options Study (''Vision 2012''), the Canyon Disposal Initiative Record-of-Decision, and the Hanford Site Solid (Radioactive and Hazardous) Waste Program Environmental Impact Statement (SW-EIS). Disposition plans may include variations of several options, including (1) sending most RH-TRU/TRUM wastes to WIPP, (2) deferrals of waste disposal decisions in the interest of both efficiency and integration with other planned decision dates and (3) disposition of some materials in place consistent with Department of Energy Orders and the regulations in the interest of safety, risk minimization, and cost. Although finalization of disposition paths must await completion of the aforementioned decision documents, significant activities in support of RH-TRU/TRUM waste disposition are proceeding, including Hanford participation in development of the RH TRU WIPP waste acceptance criteria, preparation of T Plant for interim storage of spent nuclear fuel sludge, sharing of technology information and development activities in cooperation with the Mixed Waste Focus Area, RH-TRU technology demonstrations and deployments, and

TRU Waste Inventory Collection and Work-Off Plans for the Centralization of TRU Waste Characterization/Certification at INL - On Your Mark - Get Set

International Nuclear Information System (INIS)

McTaggart, J.; Lott, S.

2009-01-01

The U.S. Department of Energy (DOE) amended the Record of Decision (ROD) for the Waste Management Program: Treatment and Storage of Transuranic Waste to centralize transuranic (TRU) waste characterization/certification from fourteen TRU waste sites. This centralization will allow for treatment, characterization and certification of TRU waste from the fourteen sites, thirteen of which are sites with small quantities of TRU waste, at the Idaho National Laboratory (INL) prior to shipping the waste to the Waste Isolation Pilot Plant (WIPP) for disposal. Centralization of this TRU waste will avoid the cost of building treatment, characterization, certification, and shipping capabilities at each of the small quantity sites that currently do not have existing facilities. Advanced Mixed Waste Treatment Project (AMWTP) and Idaho Nuclear Technology and Engineering Center (INTEC) will provide centralized shipping facilities, to WIPP, for all of the small quantity sites. Hanford, the one large quantity site identified in the ROD, has a large number of waste in containers that are over-packed into larger containers which are inefficient for shipment to and disposal at WIPP. The AMWTP at the INL will reduce the volume of much of the CH waste and make it much more efficient to ship and dispose of at WIPP. In addition, the INTEC has a certified remote handled (RH) TRU waste characterization/certification program at INL to disposition TRU waste from the sites identified in the ROD. (authors)

Comparison between TRU burning reactors and commercial fast reactor

International Nuclear Information System (INIS)

Fujimura, Koji; Sanda, Toshio; Ogawa, Takashi

2001-03-01

Research and development for stabilizing or shortening the radioactive wastes including in spent nuclear fuel are widely conducted in view point of reducing the environmental impact. Especially it is effective way to irradiate and transmute long-lived TRU by fast reactors. Two types of loading way were previously proposed. The former is loading relatively small amount of TRU in all commercial fast reactors and the latter is loading large amount of TRU in a few TRU burning reactors. This study has been intended to contribute to the feasibility studies on commercialized fast reactor cycle system. The transmutation and nuclear characteristics of TRU burning reactors were evaluated and compared with those of conventional transmutation system using commercial type fast reactor based upon the investigation of technical information about TRU burning reactors. Major results are summarized as follows. (1) Investigation of technical information about TRU burning reactors. Based on published reports and papers, technical information about TRU burning reactor concepts transmutation system using convectional commercial type fast reactors were investigated. Transmutation and nuclear characteristics or R and D issue were investigated based on these results. Homogeneously loading of about 5 wt% MAs on core fuels in the conventional commercial type fast reactor may not cause significant impact on the nuclear core characteristics. Transmutation of MAs being produced in about five fast reactors generating the same output is feasible. The helium cooled MA burning fast reactor core concept propose by JAERI attains criticality using particle type nitride fuels which contain more than 60 wt% MA. This reactor could transmute MAs being produced in more than ten 1000 MWe-LWRs. Ultra-long life core concepts attaining more than 30 years operation without refueling by utilizing MA's nuclear characteristics as burnable absorber and fertile nuclides were proposed. Those were pointed out that

Pre-1970 transuranic solid waste at the Hanford Site

International Nuclear Information System (INIS)

Greenhalgh, W.O.

1995-01-01

The document is based on a search of pre-1970 Hanford Solid Waste Records. The available data indicates seven out of thirty-one solid waste burial sites used for pre-1970 waste appear to be Transuranic (TRU). A burial site defined to be TRU contains >100 nCi/gm Transuranic nuclides

Major Components of the National TRU Waste System Optimization Project

International Nuclear Information System (INIS)

Moody, D.C.; Bennington, B.; Sharif, F.

2002-01-01

The National Transuranic (TRU) Program (NTP) is being optimized to allow for disposing of the legacy TRU waste at least 10 years earlier than originally planned. This acceleration will save the nation an estimated $713. The Department of Energy's (DOE'S) Carlsbad Field Office (CBFO) has initiated the National TRU Waste System Optimization Project to propose, and upon approvaI, implement activities that produce significant cost saving by improving efficiency, thereby accelerating the rate of TRU waste disposal without compromising safety. In its role as NTP agent of change, the National TRU Waste System Optimization Project (the Project) (1) interacts closely with all NTP activities. Three of the major components of the Project are the Central Characterization Project (CCP), the Central Confirmation Facility (CCF), and the MobiIe/Modular Deployment Program.

Preliminary hydrogeologic investigation of the Maxey Flats radioactive waste burial site, Fleming County, Kentucky

Science.gov (United States)

Zehner, Harold H.

1979-01-01

Burial trenches at the Maxey Flats radioactive waste burial site , Fleming County, Ky., cover an area of about 0.03 square mile, and are located on a plateau, about 300 to 400 feet above surrounding valleys. Although surface-water characteristics are known, little information is available regarding the ground-water hydrology of the Maxey Flats area. If transport of radionuclides from the burial site were to occur, water would probably be the principal mechanism of transport by natural means. Most base flow in streams around the burial site is from valley alluvium, and from the mantle of regolith, colluvium, and soil partially covering adjacent hills. Very little base flow is due to ground-water flow from bedrock. Most water in springs is from the mantle, rather than from bedrock. Rock units underlying the Maxey Flats area are, in descending order, the Nancy and Farmers Members of the Borden Formation, Sunbury, Bedford, and Ohio Shales, and upper part of the Crab Orchard Formation. These units are mostly shales, except for the Farmers Member, which is mostly sandstone. Total thickness of the rocks is about 320 feet. All radioactive wastes are buried in the Nancy Member. Most ground-water movement in bedrock probably occurs in fractures. The ground-water system at Maxey Flats is probably unconfined, and recharge occurs by (a) infiltration of rainfall into the mantle, and (b) vertical, unsaturated flow from the saturated regolith on hilltops to saturated zones in the Farmers Member and Ohio Shale. Data are insufficient to determine if saturated zones exist in other rock units. The upper part of the Crab Orchard Formation is probably a hydrologic boundary, with little ground-water flow through the formation. (USGS)

Environmental assessment for Trench 33 widening in 218-W-5 Low-Level Burial Ground, Hanford Site, Richland, Washington

International Nuclear Information System (INIS)

1997-07-01

This environmental assessment (EA) has been prepared to assess potential environmental impacts associated with the US Department of Energy''s proposed action: to widen and operated the unused Trench 33 in the 218-W-5 Low-Level Burial Ground. Information contained herein will be used by the US Department of Energy, Richland Operations Office Manager, to determine if the Proposed Action is a major federal action significantly affecting the quality of the human environment. If the Proposed Action is determined to be major and significant, an environmental impact statement will be prepared. If the Proposed Action is determined not to be major and significant, a Finding of No significant Impact will be issued and the action may proceed

Environmental assessment for Trench 33 widening in 218-W-5 Low-Level Burial Ground, Hanford Site, Richland, Washington

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-01

This environmental assessment (EA) has been prepared to assess potential environmental impacts associated with the US Department of Energy`s proposed action: to widen and operated the unused Trench 33 in the 218-W-5 Low-Level Burial Ground. Information contained herein will be used by the US Department of Energy, Richland Operations Office Manager, to determine if the Proposed Action is a major federal action significantly affecting the quality of the human environment. If the Proposed Action is determined to be major and significant, an environmental impact statement will be prepared. If the Proposed Action is determined not to be major and significant, a Finding of No significant Impact will be issued and the action may proceed.

TRU waste-assay instrumentation and application in nuclear-facility decommissioning

International Nuclear Information System (INIS)

Umbarger, C.J.

1982-01-01

The Los Alamos TRU waste assay program is developing measurement techniques for TRU and other radioactive waste materials generated by the nuclear industry, including decommissioning programs. Systems are now being fielded for test and evaluation purposes at DOE TRU waste generators. The transfer of this technology to other facilities and the commercial instrumentation sector is well in progress. 6 figures

Global cooperation and conceptual design toward GNEP. Enhanced TRU burning fast reactor

International Nuclear Information System (INIS)

Ikeda, Kazumi; Maddox, James W.; Nakazato, Wataru; Kunishima, Shigeru

2008-01-01

In support of the GNEP (Global Nuclear Energy Partnership) program, AREVA and Mitsubishi Heavy Industries, Ltd. (MHI) seek to develop an ARR (Advanced Recycling Reactor) in concern with a CFTC (Consolidated Fuel Treatment Facility). This report presents the examination of more effective transuranics (TRU) burning core. Therefore some innovative technologies have been examined under the safety requirements; MA bearing fuel with 50% TRU fraction, moderator pin, fuel of high Am fraction, and Am blanket. The function of moderator is to enhance TRU burning capability, while increasing the Doppler effect and reducing the positive sodium void effect. The aim of 50% TRU fraction is to increase TRU burning capability by curbing plutonium production. Both high Am fraction of fuel and Am blanket can promote Am transmutation. According to the detailed calculation of high TRU (MA 15%, Pu 35% average) contained oxide fueled core with moderator pins of 12% arranged driver fuel assemblies, TRU conversion ratio decreases down to 0.33 and TRU burning capability is improved to 67kg/TWeh. Deploying Am blanket which is oxide fuel with Am 50% and U 50%, the total of Am transmutation capability becomes 69 kg/TWeh. (author)

Empātijas atšķirības improvizācijas teātru, amatierteātru un koru dalībniekiem

OpenAIRE

Nikolajeva, Inga

2012-01-01

Pētījuma mērķis ir noskaidrot empātijas atšķirības starp improvizācijas teātru, amatierteātru un koru dalībniekiem. Izlasi veido 106 respondenti, no tiem 41 improvizācijas teātru dalībnieks, 34 amatierteātru dalībnieki un 31 koru dalībnieks kā kontroles grupa – respondenti, kuriem tā ir brīvā laika aktivitāte ārpus darba. Dalībnieki ir 14 vīrieši un 92 sievietes vecumā no 18 līdz 30 gadiem, dalībnieku pieredzes ilgums aktiermākslā ir no 1 līdz 15 gadiem. Pētījumā tiek izmantota Saimona Barona...

Remote Handled TRU Waste Status and Activities and Challenges at the Hanford Site

International Nuclear Information System (INIS)

MCKENNEY, D.E.

2000-01-01

A significant portion of the Department of Energy's forecast volume of remote-handled (RH) transuranic (TRU) waste will originate from the Hanford Site. The forecasted Hanford RH-TRU waste volume of over 2000 cubic meters may constitute over one-third of the forecast inventory of RH-TRU destined for disposal at the Waste Isolation Pilot Plant (WIPP). To date, the Hanford TRU waste program has focused on the retrieval, treatment and certification of the contact-handled transuranic (CH-TRU) wastes. This near-term focus on CH-TRU is consistent with the National TRU Program plans and capabilities. The first shipment of CH-TRU waste from Hanford to the WIPP is scheduled early in Calendar Year 2000. Shipments of RH-TRU from Hanford to the WIPP are scheduled to begin in Fiscal Year 2006 per the National TRU Waste Management Plan. This schedule has been incorporated into milestones within the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement). These Tri-Party milestones (designated the ''M-91'' series of milestones) relate to development of project management plans, completion of design efforts, construction and contracting schedules, and initiation of process operations. The milestone allows for modification of an existing facility, construction of a new facility, and/or commercial contracting to provide the capabilities for processing and certification of RH-TRU wastes for disposal at the WIPP. The development of a Project Management Plan (PMP) for TRU waste is the first significant step in the development of a program for disposal of Hanford's RH-TRU waste. This PMP will address the path forward for disposition of waste streams that cannot be prepared for disposal in the Hanford Waste Receiving and Processing facility (a contact-handled, small container facility) or other Site facilities. The PMP development effort has been initiated, and the PMP will be provided to the regulators for their approval by June 30, 2000. This plan will detail the

Guidelines for selecting codes for ground-water transport modeling of low-level waste burial sites. Volume 2. Special test cases

International Nuclear Information System (INIS)

Simmons, C.S.; Cole, C.R.

1985-08-01

This document was written for the National Low-Level Waste Management Program to provide guidance for managers and site operators who need to select ground-water transport codes for assessing shallow-land burial site performance. The guidance given in this report also serves the needs of applications-oriented users who work under the direction of a manager or site operator. The guidelines are published in two volumes designed to support the needs of users having different technical backgrounds. An executive summary, published separately, gives managers and site operators an overview of the main guideline report. Volume 1, titled ''Guideline Approach,'' consists of Chapters 1 through 5 and a glossary. Chapters 2 through 5 provide the more detailed discussions about the code selection approach. This volume, Volume 2, consists of four appendices reporting on the technical evaluation test cases designed to help verify the accuracy of ground-water transport codes. 20 refs

TRU Self-Recycling in a High Temperature Gas Cooled Reactor

International Nuclear Information System (INIS)

Jo, Chang Keun

2013-01-01

Conclusions: • Evaluated the core characteristics and performance for SR-HTR. • Self-recycling of self-generated TRUs is feasible and deep-burning of the self-generated TRU can be achieved in SR-HTR. • From the results, ⇒ TRU discharge burnup is over 60% and the uranium fuel can also be utilized very efficiently in the SR-HTR core. ⇒ In the case of separate TRU loading, the power fraction of the TRU fueled zone is substantially smaller (~10%) than that of the uranium fueled zone. ⇒ The transmutation of Pu-239 is nearly complete (~99%) in the SR-HTR core and that of Pu-241 is also extremely high. ⇒ The decay heat of SR-HTR core is evaluated to be similar to that of the 3-ring UO 2 -only loaded HTR core. • A TF-coupled analysis is required for a more concrete evaluation of TRU deep-burn in an SR-HTR

On the Semantics of Plates from the Shilovka Burial Ground

Directory of Open Access Journals (Sweden)

Fonyakova (Chuvilo Natalia A.

2013-03-01

Full Text Available Among the finds made on the sites located in the Middle Volga region and Siberia, ivory plaques of high artistic value used to adorn combat saddle pommel are met. They would bear floral ornamentation or depict hunting scenes, reflecting the spiritual world of a nomad warrior. These images are dated widely, but not later than the 7th or 8th centuries. They were drawn with a sharp cutter and blackened down the lines. Of special interest are the bone plates from the Shilovka burial ground site (Uyanovsk oblast with the following images: two dragons in a heraldic posture, deer hunt scenes, horsemen in ambush, fight with a bear, and defense of the fortress. In the author’s opinion, the Shilovka plates depict a dramatic episode in the life of a Turkic warlord, which occurred in the midst of hostilities. During the hunt, a huge bear was unleashed against him. Part of his heavily armed convoy (or suite fled; some soldiers got ambushed (the enemy shot them from armor-piercing bows. Saving his life, the captain knelt and bent his bow, whose string broke at the most inopportune moment. Perhaps he died fighting a bear. One can assume that it was a stratagem of the enemy, which decided the outcome of the war. The symbol of victory on the plates is represented by the dragons, frozen in a heraldic posture, and expressing the basic principle of life characteristic of the nomad warriors in the Early Middle Ages: prosperity and well-being at a price of war and victories. The plaques were placed into the winner’s grave.

Performance assessment for the disposal of low-level waste in the 200 West Area Burial Grounds

Energy Technology Data Exchange (ETDEWEB)

Wood, M.I.; Khaleel, R.; Rittmann, P.D.; Lu, A.H.; Finfrock, S.H.; DeLorenzo, T.H. [Westinghouse Hanford Co., Richland, WA (United States); Serne, R.J.; Cantrell, K.J. [Pacific Northwest Lab., Richland, WA (United States)

1995-06-01

This document reports the findings of a performance assessment (PA) analysis for the disposal of solid low-level radioactive waste (LLW) in the 200 West Area Low-Level Waste Burial Grounds (LLBG) in the northwest corner of the 200 West Area of the Hanford Site. This PA analysis is required by US Department of Energy (DOE) Order 5820.2A (DOE 1988a) to demonstrate that a given disposal practice is in compliance with a set of performance objectives quantified in the order. These performance objectives are applicable to the disposal of DOE-generated LLW at any DOE-operated site after the finalization of the order in September 1988. At the Hanford Site, DOE, Richland Operations Office (RL) has issued a site-specific supplement to DOE Order 5820.2A, DOE-RL 5820.2A (DOE 1993), which provides additiona I ce objectives that must be satisfied.

Performance assessment for the disposal of low-level waste in the 200 West Area Burial Grounds

International Nuclear Information System (INIS)

Wood, M.I.; Khaleel, R.; Rittmann, P.D.; Lu, A.H.; Finfrock, S.H.; DeLorenzo, T.H.; Serne, R.J.; Cantrell, K.J.

1995-06-01

This document reports the findings of a performance assessment (PA) analysis for the disposal of solid low-level radioactive waste (LLW) in the 200 West Area Low-Level Waste Burial Grounds (LLBG) in the northwest corner of the 200 West Area of the Hanford Site. This PA analysis is required by US Department of Energy (DOE) Order 5820.2A (DOE 1988a) to demonstrate that a given disposal practice is in compliance with a set of performance objectives quantified in the order. These performance objectives are applicable to the disposal of DOE-generated LLW at any DOE-operated site after the finalization of the order in September 1988. At the Hanford Site, DOE, Richland Operations Office (RL) has issued a site-specific supplement to DOE Order 5820.2A, DOE-RL 5820.2A (DOE 1993), which provides additiona I ce objectives that must be satisfied

CH-TRU Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2005-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-10-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

The Advantages of Fixed Facilities in Characterizing TRU Wastes

International Nuclear Information System (INIS)

FRENCH, M.S.

2000-01-01

In May 1998 the Hanford Site started developing a program for characterization of transuranic (TRU) waste for shipment to the Waste Isolation Pilot Plant (WIPP) in New Mexico. After less than two years, Hanford will have a program certified by the Carlsbad Area Office (CAO). By picking a simple waste stream, taking advantage of lessons learned at the other sites, as well as communicating effectively with the CAO, Hanford was able to achieve certification in record time. This effort was further simplified by having a centralized program centered on the Waste Receiving and Processing (WRAP) Facility that contains most of the equipment required to characterize TRU waste. The use of fixed facilities for the characterization of TRU waste at sites with a long-term clean-up mission can be cost effective for several reasons. These include the ability to control the environment in which sensitive instrumentation is required to operate and ensuring that calibrations and maintenance activities are scheduled and performed as an operating routine. Other factors contributing to cost effectiveness include providing approved procedures and facilities for handling hazardous materials and anticipated contingencies and performing essential evolutions, and regulating and smoothing the work load and environmental conditions to provide maximal efficiency and productivity. Another advantage is the ability to efficiently provide characterization services to other sites in the Department of Energy (DOE) Complex that do not have the same capabilities. The Waste Receiving and Processing (WRAP) Facility is a state-of-the-art facility designed to consolidate the operations necessary to inspect, process and ship waste to facilitate verification of contents for certification to established waste acceptance criteria. The WRAP facility inspects, characterizes, treats, and certifies transuranic (TRU), low-level and mixed waste at the Hanford Site in Washington state. Fluor Hanford operates the $89

Thermal treatment for TRU waste sorting

International Nuclear Information System (INIS)

Sasaki, Toshiki; Aoyama, Yoshio; Yamashita, Toshiyuki

2009-03-01

A thermal treatment that can automatically unpack TRU waste and remove hazardous materials has been developed to reduce the risk of radiation exposure and save operation cost. The thermal treatment is a process of removing plastic wrapping and hazardous material from TRU waste by heating waste at 500 to 700degC. Plastic wrappings of simulated wastes were removed using a laboratory scale thermal treatment system. Celluloses and isoprene rubbers that must be removed from waste for disposal were pyrolyzed by the treatment. Although the thermal treatment can separate lead and aluminum from the waste, a further technical development is needed to separate lead and aluminum. A demonstration scale thermal treatment system that comprises a rotary kiln with a jacket water cooler and a rotating inner cage for lead and aluminum separation is discussed. A clogging prevention system against zinc chloride, a lead and aluminum accumulation system, and a detection system for spray cans that possibly cause explosion and fire are also discussed. Future technology development subjects for the TRU waste thermal treatment system are summarized. (author)

Final Hanford Site Transuranic (TRU) Waste Characterization QA Project Plan

International Nuclear Information System (INIS)

GREAGER, T.M.

2000-01-01

The Quality Assurance Project Plan (QAPjP) has been prepared for waste characterization activities to be conducted by the Transuranic (TRU) Project at the Hanford Site to meet requirements set forth in the Waste Isolation Pilot Plan (WIPP) Hazardous Waste Facility Permit, 4890139088-TSDF, Attachment B, including Attachments B1 through B6 (WAP) (DOE, 1999a). The QAPjP describes the waste characterization requirements and includes test methods, details of planned waste sampling and analysis, and a description of the waste characterization and verification process. In addition, the QAPjP includes a description of the quality assurance/quality control (QA/QC) requirements for the waste characterization program. Before TRU waste is shipped to the WIPP site by the TRU Project, all applicable requirements of the QAPjP shall be implemented. Additional requirements necessary for transportation to waste disposal at WIPP can be found in the ''Quality Assurance Program Document'' (DOE 1999b) and HNF-2600, ''Hanford Site Transuranic Waste Certification Plan.'' TRU mixed waste contains both TRU radioactive and hazardous components, as defined in the WLPP-WAP. The waste is designated and separately packaged as either contact-handled (CH) or remote-handled (RH), based on the radiological dose rate at the surface of the waste container. RH TRU wastes are not currently shipped to the WIPP facility

Behavior of nuclides at plasma melting of TRU wastes

International Nuclear Information System (INIS)

Amakawa, Tadashi; Adachi, Kazuo

2001-01-01

Arc plasma heating technique can easily be formed at super high temperature, and can carry out stable heating without any effect of physical and chemical properties of the wastes. By focussing to these characteristics, this technique was experimentally investigated on behavior of TRU nuclides when applying TRU wastes forming from reprocessing process of used fuels to melting treatment by using a mimic non-radioactive nuclide. At first, according to mechanism determining the behavior of TRU nuclides, an element (mimic nuclide) to estimate the behavior was selected. And then, to zircaloy with high melting point or steel can simulated to metal and noncombustible wastes and fly ash, the mimic nuclide was added, prior to melting by using the arc plasma heating technique. As a result, on a case of either melting sample, it was elucidated that the nuclides hardly moved into their dusts. Then, the technique seems to be applicable for melting treatment of the TRU wastes. (G.K.)

Carbon sequestration via wood burial

Directory of Open Access Journals (Sweden)

Zeng Ning

2008-01-01

Full Text Available Abstract To mitigate global climate change, a portfolio of strategies will be needed to keep the atmospheric CO2 concentration below a dangerous level. Here a carbon sequestration strategy is proposed in which certain dead or live trees are harvested via collection or selective cutting, then buried in trenches or stowed away in above-ground shelters. The largely anaerobic condition under a sufficiently thick layer of soil will prevent the decomposition of the buried wood. Because a large flux of CO2 is constantly being assimilated into the world's forests via photosynthesis, cutting off its return pathway to the atmosphere forms an effective carbon sink. It is estimated that a sustainable long-term carbon sequestration potential for wood burial is 10 ± 5 GtC y-1, and currently about 65 GtC is on the world's forest floors in the form of coarse woody debris suitable for burial. The potential is largest in tropical forests (4.2 GtC y-1, followed by temperate (3.7 GtC y-1 and boreal forests (2.1 GtC y-1. Burying wood has other benefits including minimizing CO2 source from deforestation, extending the lifetime of reforestation carbon sink, and reducing fire danger. There are possible environmental impacts such as nutrient lock-up which nevertheless appears manageable, but other concerns and factors will likely set a limit so that only part of the full potential can be realized. Based on data from North American logging industry, the cost for wood burial is estimated to be $14/tCO2($50/tC, lower than the typical cost for power plant CO2 capture with geological storage. The cost for carbon sequestration with wood burial is low because CO2 is removed from the atmosphere by the natural process of photosynthesis at little cost. The technique is low tech, distributed, easy to monitor, safe, and reversible, thus an attractive option for large-scale implementation in a world-wide carbon market.

A study for the safety evaluation of geological disposal of TRU waste and influence on disposal site design by change of amount of TRU waste (Joint research)

International Nuclear Information System (INIS)

Hasegawa, Makoto; Kondo, Hitoshi; Takahashi, Kuniaki; Funabashi, Hideaki; Kawatsuma, Shinji; Kamei, Gento; Hirano, Fumio; Mihara, Morihiro; Ueda, Hiroyoshi; Ohi, Takao; Hyodo, Hideaki

2011-02-01

In the safety evaluation of the geological disposal of the TRU waste, it is extremely important to share the information with the Research and development organization (JAEA: that is also the waste generator) by the waste disposal entrepreneur (NUMO). In 2009, NUMO and JAEA set up a technical commission to investigate the reasonable TRU waste disposal following a cooperation agreement between these two organizations. In this report, the calculation result of radionuclide transport for a TRU waste geological disposal system was described, by using the Tiger code and the GoldSim code at identical terms. Tiger code is developed to calculate a more realistic performance assessment by JAEA. On the other hand, GoldSim code is the general simulation software that is used for the computation modeling of NUMO TRU disposal site. Comparing the calculation result, a big difference was not seen. Therefore, the reliability of both codes was able to be confirmed. Moreover, the influence on the disposal site design (Capacity: 19,000m 3 ) was examined when 10% of the amount of TRU waste increased. As a result, it was confirmed that the influence of the site design was very little based on the concept of the Second Progress Report on Research and Development for TRU Waste Disposal in Japan. (author)

Design criteria burial containers for non-transuranic solid radioactive waste

International Nuclear Information System (INIS)

Hammond, J.E.

1976-01-01

The criteria, replace HW-83959 and apply to containers constructed specifically for the containment of beta-gamma radioactively contaminated waste removed from an area controlled by radiation work procedures, transported across an uncontrolled area where there is risk of a radiation release to the environs, and buried in an approved radioactive waste burial ground

Los Alamos Plutonium Facility newly generated TRU waste certification

International Nuclear Information System (INIS)

Gruetzmacher, K.; Montoya, A.; Sinkule, B.; Maez, M.

1997-01-01

This paper presents an overview of the activities being planned and implemented to certify newly generated contact handled transuranic (TRU) waste produced by Los Alamos National Laboratory's (LANL's) Plutonium Facility. Certifying waste at the point of generation is the most important cost and labor saving step in the WIPP certification process. The pedigree of a waste item is best known by the originator of the waste and frees a site from expensive characterization activities such as those associated with legacy waste. Through a cooperative agreement with LANLs Waste Management Facility and under the umbrella of LANLs WIPP-related certification and quality assurance documents, the Plutonium Facility will be certifying its own newly generated waste. Some of the challenges faced by the Plutonium Facility in preparing to certify TRU waste include the modification and addition of procedures to meet WIPP requirements, standardizing packaging for TRU waste, collecting processing documentation from operations which produce TRU waste, and developing ways to modify waste streams which are not certifiable in their present form

Optimization of TRU burnup in modular helium reactor

International Nuclear Information System (INIS)

Yonghee, Kim; Venneri, F.

2007-01-01

An optimization study of a single-pass TRU (transuranic) deep-burn (DB) has been performed for a block-type MHR (Modular Helium Reactor) proposed by General Atomics. Assuming a future equilibrium scenario of advanced LWRs, a high-burnup TRU vector is considered: 50 GWD/MTU and 5-year cooling. For 3-D equilibrium cores, the performance analysis is done by using a continuous energy Monte Carlo depletion code MCCARD. The core optimization is performed from the viewpoints of the core configuration, fuel management, TRISO fuel specification, and neutron spectrum. With regard to core configuration, two annular cores are investigated in terms of the neutron economy. A conventional radial shuffling scheme of fuel blocks is compared with an axial block shuffling strategy in terms of the fuel burnup and core power distributions. The impact of the kernel size of TRISO fuel is evaluated and a diluted kernel, instead of a conventional concentrated kernel, is introduced to maximize the TRU burnup by reducing the self-shielding effects of TRISO fuels. A higher graphite density is evaluated in terms of the fuel burnup. In addition, it is shown that the core power distribution can be effectively controlled by zoning of the packing fraction of TRISO fuels. We also have shown that a long-cycle DB-MHR core can be designed by using a small batch size for fuel reloading, at the expense of a marginal decrease of the TRU discharge burnup. Depending on the fuel management scheme, fuel specifications, and core parameters, the TRU burnup in an optimized DB-MHR core is over 60% in a single-pass irradiation campaign. (authors)

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2007-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2006-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2005-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2004-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2008-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-09-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-05-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-02-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-06-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-06-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-01-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codesand corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-12-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-08-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-01-18

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2004-10-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-03-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-09-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-08-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2004-12-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-11-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-12-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-01-30

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-08-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-06-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

Guidelines for selecting codes for ground-water transport modeling of low-level waste burial sites. Volume 1. Guideline approach

Energy Technology Data Exchange (ETDEWEB)

Simmons, C.S.; Cole, C.R.

1985-05-01

This document was written for the National Low-Level Waste Management Program to provide guidance for managers and site operators who need to select ground-water transport codes for assessing shallow-land burial site performance. The guidance given in this report also serves the needs of applications-oriented users who work under the direction of a manager or site operator. The guidelines are published in two volumes designed to support the needs of users having different technical backgrounds. An executive summary, published separately, gives managers and site operators an overview of the main guideline report. This volume includes specific recommendations for decision-making managers and site operators on how to use these guidelines. The more detailed discussions about the code selection approach are provided. 242 refs., 6 figs.

Guidelines for selecting codes for ground-water transport modeling of low-level waste burial sites. Volume 1. Guideline approach

International Nuclear Information System (INIS)

Simmons, C.S.; Cole, C.R.

1985-05-01

This document was written for the National Low-Level Waste Management Program to provide guidance for managers and site operators who need to select ground-water transport codes for assessing shallow-land burial site performance. The guidance given in this report also serves the needs of applications-oriented users who work under the direction of a manager or site operator. The guidelines are published in two volumes designed to support the needs of users having different technical backgrounds. An executive summary, published separately, gives managers and site operators an overview of the main guideline report. This volume includes specific recommendations for decision-making managers and site operators on how to use these guidelines. The more detailed discussions about the code selection approach are provided. 242 refs., 6 figs

Deep-Burn MHR Neutronic Analysis with a SiC-Gettered TRU Kernel

International Nuclear Information System (INIS)

Jo, Chang Keun; Noh, Jae Man; Kim, Yong Hee; Venneric, F.

2010-01-01

This paper is focused on the nuclear core design of a DB-MHR (Deep Burn-Modular Helium Reactor) core loaded with a SiC-gettered TRU fuel. The SiC oxygen getter is added to reduce the CO pressure in the buffer zone of TRISO. In the paper, the cycle length, reactivity swing, discharged burnup, and the burning rate of plutonium were calculated for the DB-MHR. Also, impacts of uranium addition to the TRU kernel were investigated. Recently, the decay heat of TRU fueled DB core was found to be highly dependent on the TRU loading: the higher the loading, the higher the decay heat. The high decay heat of TRU fuel may lead to unacceptably high peak fuel temperature during an LPCC (Low Pressure Conduction Cooling) accident. Thus, we tried to minimize the decay heat of the core for a minimal peak fuel temperature during LPCC

Vitrification of TRU wastes at Rocky Flats Plant

International Nuclear Information System (INIS)

Williams, P.M.; Johnson, A.J.; Ledford, J.A.

1979-01-01

Immobilization of incinerator ash and various noncombustible TRU wastes was investigated. In three different research projects borosilicate glass proved to be the best candidate for TRU waste fixation. This glass has excellent chemical durability, long-term stability in the presence of radiation, and will withstand continuous temperatures up to 400 0 C without devitrification. In addition, wastes prepared in the form of glass will attain densities of approximately 2500 kg/m 3 (2.5 g/cc). The free forming method of producing glass buttons provides a very simple, consistent, low maintenance way of producing a final waste form for transporting and either retrievable or permanent storage for TRU waste. The vitrification process produces a durable glass from the low density ash generated by the fluidized bed incinerator process and provides volume and weight reductions that are superior to other fixation processes. This results in decreased transportation and storage costs

GAMMA-PULSE-HEIGHT EVALUATION OF A USA SAVANNAH RIVER SITE BURIAL GROUND SPECIAL CONFIGURATION WASTE ITEM

International Nuclear Information System (INIS)

Dewberry, R.; Sigg, R.; Salaymeh, S.

2009-01-01

The Savannah River Site (SRS) Burial Ground had a container labeled as Box 33 for which they had no reliable solid waste stream designation. The container consisted of an outer box of dimensions 48-inch x 46-inch x 66-inch and an inner box that contained high density and high radiation dose material. From the outer box Radiation Control measured an extremity dose rate of 22 mrem/h. With the lid removed from the outer box, the maximum dose rate measured from the inner box was 100 mrem/h extremity and 80 mrem/h whole body. From the outer box the material was sufficiently high in density that the Solid Waste Management operators were unable to obtain a Co-60 radiograph of the contents. Solid Waste Management requested that the Analytical Development Section of Savannah River National Laboratory perform a γ-ray assay of the item to evaluate the radioactive content and possibly to designate a solid waste stream. This paper contains the results of three models used to analyze the measured γ-ray data acquired in an unusual configuration

GAMMA-PULSE-HEIGHT EVALUATION OF A USA SAVANNAH RIVER SITE BURIAL GROUND SPECIAL CONFIGURATION WASTE ITEM

Energy Technology Data Exchange (ETDEWEB)

Dewberry, R.; Sigg, R.; Salaymeh, S.

2009-03-23

The Savannah River Site (SRS) Burial Ground had a container labeled as Box 33 for which they had no reliable solid waste stream designation. The container consisted of an outer box of dimensions 48-inch x 46-inch x 66-inch and an inner box that contained high density and high radiation dose material. From the outer box Radiation Control measured an extremity dose rate of 22 mrem/h. With the lid removed from the outer box, the maximum dose rate measured from the inner box was 100 mrem/h extremity and 80 mrem/h whole body. From the outer box the material was sufficiently high in density that the Solid Waste Management operators were unable to obtain a Co-60 radiograph of the contents. Solid Waste Management requested that the Analytical Development Section of Savannah River National Laboratory perform a {gamma}-ray assay of the item to evaluate the radioactive content and possibly to designate a solid waste stream. This paper contains the results of three models used to analyze the measured {gamma}-ray data acquired in an unusual configuration.

Los Alamos National Laboratory TRU waste sampling projects

International Nuclear Information System (INIS)

Yeamans, D.; Rogers, P.; Mroz, E.

1997-01-01

The Los Alamos National Laboratory (LANL) has begun characterizing transuranic (TRU) waste in order to comply with New Mexico regulations, and to prepare the waste for shipment and disposal at the Waste Isolation Pilot Plant (WIPP), near Carlsbad, New Mexico. Sampling consists of removing some head space gas from each drum, removing a core from a few drums of each homogeneous waste stream, and visually characterizing a few drums from each heterogeneous waste stream. The gases are analyzed by GC/MS, and the cores are analyzed for VOC's and SVOC's by GC/MS and for metals by AA or AE spectroscopy. The sampling and examination projects are conducted in accordance with the ''DOE TRU Waste Quality Assurance Program Plan'' (QAPP) and the ''LANL TRU Waste Quality Assurance Project Plan,'' (QAPjP), guaranteeing that the data meet the needs of both the Carlsbad Area Office (CAO) of DOE and the ''WIPP Waste Acceptance Criteria, Rev. 5,'' (WAC)

Biobarriers used in shallow-burial ground stabilization

International Nuclear Information System (INIS)

Cline, J.F.

1979-03-01

These data show that cobblestone can be effective as a barrier to burrowing animals and insects, but not totally effective as a barrier to plant roots. Because of variable weather patterns at Hanford, five to six year studies are recommended for further evaluation of the effectiveness of different materials as biobarriers to radioactive substances. The following criteria must be met to present plant roots from entering buried waste and transporting radioactive or other elements to the soil surface where they can enter the food web: (1) the burial zone beneath the cover should be kept dry; (2) enough soil or other water-retaining substance should be placed in the cover to hold annual precipitation; (3) plants or other substances should be placed in the cover to remove soil moisture from site each year via evaporation and plant transpiration; and (4) different additions to the cover should be designed and placed over the buried waste to prevent burrowing animals from causing channelization of water through the cover to the lower levels. Stone size appeared to affect the plants' rate of root growth since root growth slowed in the air spaces between stones. Root toxin was 100% effective as a means of keeping roots out of the buried waste; this method could be used as a barrier modification where no plant cover is needed. 9 figures, 2 tables

Los Alamos controlled air incinerator upgrade for TRU/mixed waste operations

International Nuclear Information System (INIS)

Vavruska, J.S.; Borduin, L.C.; Hutchins, D.A.; Warner, C.L.; Thompson, T.K.

1989-01-01

The Los Alamos Controlled Air Incinerator (CAI) is undergoing a major process upgrade to accept Laboratory-generated transuranic (TRU) and TRU mixed wastes on a production basis. In the interim,prior to the scheduled 1992 operation of a new on-site LLW/mixed waste incinerator, the CAI will also be accepting solid and liquid low-level mixed wastes. This paper describes major modifications that have been made to the process to enhance safety and ensure reliability for long-term, routine waste incineration operations. The regulatory requirements leading to operational status of the system are also briefly described. The CAI was developed in the mid-1970s as a demonstration system for volume reduction of TRU combustible solid wastes. It continues as a successful R and D system well into the 1980s during which incineration tests on a wide variety of radioactive and chemical waste forms were performed. In 1985, a DOE directive required Los Alamos to reduce the volume of its TRU waste prior to ultimate placement in the geological repository at the Waste Isolation Pilot Project (WIPP). With only minor modifications to the original process flowsheet, the Los Alamos CAI was judged capable of conversion to a TRU waste operations mode. 9 refs., 1 fig

Hybrid Microwave Treatment of SRS TRU and Mixed Wastes

International Nuclear Information System (INIS)

Wicks, G.G.

1999-01-01

A new process, using hybrid microwave energy, has been developed as part of the Strategic Research and Development program and successfully applied to treatment of a wide variety of non-radioactive materials, representative of SRS transuranic (TRU) and mixed wastes. Over 35 simulated (non-radioactive) TRU and mixed waste materials were processed individually, as well as in mixed batches, using hybrid microwave energy, a new technology now being patented by Westinghouse Savannah River Company (WSRC)

Final environmental assessment: TRU waste drum staging building, Technical Area 55, Los Alamos National Laboratory

International Nuclear Information System (INIS)

1996-01-01

Much of the US Department of Energy's (DOE's) research on plutonium metallurgy and plutonium processing is performed at Los Alamos National Laboratory (LANL), in Los Alamos, New Mexico. LANL's main facility for plutonium research is the Plutonium Facility, also referred to as Technical Area 55 (TA-55). The main laboratory building for plutonium work within the Plutonium Facility (TA-55) is the Plutonium Facility Building 4, or PF-4. This Environmental Assessment (EA) analyzes the potential environmental effects that would be expected to occur if DOE were to stage sealed containers of transuranic (TRU) and TRU mixed waste in a support building at the Plutonium Facility (TA-55) that is adjacent to PF-4. At present, the waste containers are staged in the basement of PF-4. The proposed project is to convert an existing support structure (Building 185), a prefabricated metal building on a concrete foundation, and operate it as a temporary staging facility for sealed containers of solid TRU and TRU mixed waste. The TRU and TRU mixed wastes would be contained in sealed 55-gallon drums and standard waste boxes as they await approval to be transported to TA-54. The containers would then be transported to a longer term TRU waste storage area at TA-54. The TRU wastes are generated from plutonium operations carried out in PF-4. The drum staging building would also be used to store and prepare for use new, empty TRU waste containers

Sediment Burial Intolerance of Marine Macroinvertebrates.

Directory of Open Access Journals (Sweden)

Vicki J Hendrick

Full Text Available The marine environment contains suspended particulate matter which originates from natural and anthropogenic sources. Settlement of this material can leave benthic organisms susceptible to smothering, especially if burial is sudden i.e. following storms or activities such as dredging. Their survival will depend on their tolerance to, and their ability to escape from burial. Here we present data from a multi-factorial experiment measuring burial responses incorporating duration, sediment fraction and depth. Six macroinvertebrates commonly found in sediment rich environments were selected for their commercial and/or conservation importance. Assessments revealed that the brittle star (Ophiura ophiura, the queen scallop (Aequipecten opercularis and the sea squirt (Ciona intestinalis were all highly intolerant to burial whilst the green urchin (Psammichinus miliaris and the anemone (Sagartiogeton laceratus, showed intermediate and low intolerance respectively, to burial. The least intolerant, with very high survival was the Ross worm (Sabellaria spinulosa. With the exception of C. intestinalis, increasing duration and depth of burial with finer sediment fractions resulted in increased mortality for all species assessed. For C. intestinalis depth of burial and sediment fraction were found to be inconsequential since there was complete mortality of all specimens buried for more than one day. When burial emergence was assessed O. ophiura emerged most frequently, followed by P. miliaris. The former emerged most frequently from the medium and fine sediments whereas P. miliaris emerged more frequently from coarse sediment. Both A. opercularis and S. laceratus showed similar emergence responses over time, with A. opercularis emerging more frequently under coarse sediments. The frequency of emergence of S. laceratus increased with progressively finer sediment and C. intestinalis did not emerge from burial irrespective of sediment fraction or depth. Finally

Potential Flammable Gas Explosion in the TRU Vent and Purge Machine

International Nuclear Information System (INIS)

Vincent, A

2006-01-01

The objective of the analysis was to determine the failure of the Vent and Purge (V and P) Machine due to potential explosion in the Transuranic (TRU) drum during its venting and/or subsequent explosion in the V and P machine from the flammable gases (e.g., hydrogen and Volatile Organic Compounds [VOCs]) vented into the V and P machine from the TRU drum. The analysis considers: (a) increase in the pressure in the V and P cabinet from the original deflagration in the TRU drum including lid ejection, (b) pressure wave impact from TRU drum failure, and (c) secondary burns or deflagrations resulting from excess, unburned gases in the cabinet area. A variety of cases were considered that maximized the pressure produced in the V and P cabinet. Also, cases were analyzed that maximized the shock wave pressure in the cabinet from TRU drum failure. The calculations were performed for various initial drum pressures (e.g., 1.5 and 6 psig) for 55 gallon TRU drum. The calculated peak cabinet pressures ranged from 16 psig to 50 psig for various flammable gas compositions. The blast on top of cabinet and in outlet duct ranged from 50 psig to 63 psig and 12 psig to 16 psig, respectively, for various flammable gas compositions. The failure pressures of the cabinet and the ducts calculated by structural analysis were higher than the pressure calculated from potential flammable gas deflagrations, thus, assuring that V and P cabinet would not fail during this event. National Fire Protection Association (NFPA) 68 calculations showed that for a failure pressure of 20 psig, the available vent area in the V and P cabinet is 1.7 to 2.6 times the required vent area depending on whether hydrogen or VOCs burn in the V and P cabinet. This analysis methodology could be used to design the process equipment needed for venting TRU waste containers at other sites across the Department of Energy (DOE) Complex

Field tests on migration of TRU-nuclide, (1). General introduction

International Nuclear Information System (INIS)

Ogawa, Hiromichi; Tanaka, Tadao; Mukai, Masayuki

2003-01-01

The field migration test using TRU nuclide was carried out as a cooperative research project between JAERI (Japan Atomic Energy Research Institute) and CIRP (China Institute for Radiation Protection). This report introduced the out-line of the field migration test and described the outline of the series of 'Field Test on Migration of TRU-nuclide' and main results as a summary report. (author)

Integrated report on radionuclide migration at the Savannah River shallow land burial site

International Nuclear Information System (INIS)

Towler, O.A. Jr.

1989-03-01

The impact of the SRP Solid Radioactive Waste Burial Ground on the environment has been studied since the early 1970s in four subtasks: subsurface monitoring of groundwater, lysimeter tests of waste, soil-water chemistry effects, and radionuclide transport modeling. This document summarizes and integrates the results of the four subtasks. More information has been gathered on the behavior of radionuclides in a solid waste disposal facility located in a humid region than from any other waste disposal site in the world. The design of closure for the SRP Burial Ground has been given a firm technical basis. The limiting pathways for radionuclide migration have been determined to be infiltrating rainwater and root penetration. Closure designs must therefore address both these factors. The designs for new storage/disposal facilities have also been given a firm technical basis. The major conclusions are that tritium will be stored for decay and not allowed to contact the groundwater, waste containing long-lived radionuclides such as iodine-129 must be stored for later geologic disposal, and above and below ground concrete vaults should be used for disposal of other low-level radioactive waste. 61 refs., 18 figs. 8 tabs

Observed TRU data from nuclear utility waste streams

International Nuclear Information System (INIS)

Wessman, R.A.; Floyd, J.G.; Leventhal, L.

1990-01-01

TMA/Norcal has performed 10CFR61 analysis of radioactive waste streams from BWR's and PWR's since 1983. Many standard and non-routine sample types have been received for analysis from nuclear power plants nation-wide. In addition to the 10CFR61 Tables I and II analyses, we also have analyzed for many of the supplementary isotopes. As part of this program TRU analyses are required. As a result, have accumulated a significant amount of data for plutonium, americium, and curium in radioactive waste for many different sample matrices from many different waste streams. This paper will present our analytical program for 10CFR61 TRU. The laboratory methodology including chemical and radiometric procedures is discussed. The sensitivity of our measurements and ability to meet the lower limits of detection is also discussed. Secondly, a review of TRU data is presented. Scaling factors and their ranges from selected PWR stations are included. We discuss some features of, and limits to, interpretation of these data. 8 refs., 3 tabs

A strategy for analysis of TRU waste characterization needs

International Nuclear Information System (INIS)

Leigh, C.D.; Chu, M.S.Y.; Arvizu, J.S.; Marcinkiewicz, C.J.

1994-01-01

Regulatory compliance and effective management of the nation's TRU waste requires knowledge about the constituents present in the waste. With limited resources, the DOE needs a cost-effective characterization program. In addition, the DOE needs a method for predicting the present and future analytical requirements for waste characterization. Thus, a strategy for predicting the present and future waste characterization needs that uses current knowledge of the TRU inventory and prioritization of the data needs is presented

W-026, transuranic waste (TRU) glovebox acceptance test report

International Nuclear Information System (INIS)

Leist, K.J.

1998-01-01

On July 18, 1997, the Transuranic (TRU) glovebox was tested using glovebox acceptance test procedure 13021A-86. The primary focus of the glovebox acceptance test was to examine control system interlocks, display menus, alarms, and operator messages. Limited mechanical testing involving the drum ports, hoists, drum lifter, compacted drum lifter, drum tipper, transfer car, conveyors, sorting table, lidder/delidder device and the TRU empty drum compactor were also conducted. As of February 25, 1998, 10 of the 102 test exceptions that affect the TRU glovebox remain open. These items will be tracked and closed via the WRAP Master Test Exception Database. As part of Test Exception resolution/closure the responsible individual closing the Test Exception performs a retest of the affected item(s) to ensure the identified deficiency is corrected, and, or to test items not previously available to support testing. Test exceptions are provided as appendices to this report

An investigation of TRU recycling with various neutron spectrums

International Nuclear Information System (INIS)

Yong-Nam, Kim; Hong-Chul, Kim; Chi-Young, Han; Jong-Kyung, Kim; Won-Seok Park

2003-01-01

This study is intended to evaluate the dependency of TRU recycling characteristics on the neutron spectrum shift in a Pb-Bi cooled core. Considering two Pb-Bi cooled cores with the soft and the hard spectrum, respectively, various characteristics of the recycled core are carefully examined and compared with each other. Assuming very simplified fuel cycle management with the homogeneous and single batch fuel loading, the burn-up calculations are performed until the recycled core reached to the (quasi-) equilibrium state. The mechanism of TRU recycling toward the equilibrium is analysed in terms of burn-up reactivity and the isotopic compositions of TRU fuel. In the comparative analyses, the difference in the recycling behaviour between the two cores is clarified. In addition, the basic safety characteristics of the recycled core are also discussed in terms of the Doppler coefficient, the coolant loss reactivity coefficient, and the effective delayed neutron fraction. (author)

Documentation associated with the shipping of Hot-Cell Waste from WESF 225-B to the 200W (218-W-3AE) burial grounds under shipment number RSR-37338

International Nuclear Information System (INIS)

PAWLAK, M.W.

1998-01-01

The purpose of this report is to compile the records generated during the Packaging and Shipping of WESF Hot-Cell Waste from the 225-B Facility to 200W (218-W-3AE) burial grounds. A total of six 55-gallon drums were packaged and shipped using the Chem-Nuc Cask in accordance with WHC-SD-TP-SARP-025, Rev.0 ''Safety Analysis Report for Packaging (Onsite) for Type B Material in the CNS-14-215H Cask''

Design and testing of a unique active Compton-suppressed LaBr3(Ce) detector system for improved sensitivity assays of TRU in remote-handled TRU wastes

Energy Technology Data Exchange (ETDEWEB)

J. K. Hartwell; M. E. McIlwain; J. A. Kulisek

2007-10-01

The US Department of Energy’s transuranic (TRU) waste inventory includes about 4,500 m3 of remote-handled TRU (RH-TRU) wastes composed of a variety of containerized waste forms having a contact surface dose rate that exceeds 2 mSv/hr (200 mrem/hr) containing waste materials with a total TRU concentration greater than 3700 Bq/g (100 nCi/g). As part of a research project to investigate the use of active Compton-suppressed room-temperature gamma-ray detectors for direct non-destructive quantification of the TRU content of these RH-TRU wastes, we have designed and purchased a unique detector system using a LaBr3(Ce) primary detector and a NaI(Tl) suppression mantle. The LaBr3(Ce) primary detector is a cylindrical unit ~25 mm in diameter by 76 mm long viewed by a 38 mm diameter photomultiplier. The NaI(Tl) suppression mantle (secondary detector) is 175 mm by 175 mm with a center well that accommodates the primary detector. An important feature of this arrangement is the lack of any “can” between the primary and secondary detectors. These primary and secondary detectors are optically isolated by a thin layer (.003") of aluminized kapton, but the hermetic seal and thus the aluminum can surrounds the outer boundary of the detector system envelope. The hermetic seal at the primary detector PMT is at the PMT wall. This arrangement virtually eliminates the “dead” material between the primary and secondary detectors, a feature that preliminary modeling indicated would substantially improve the Compton suppression capability of this device. This paper presents both the expected performance of this unit determined from modeling with MCNPX, and the performance measured in our laboratory with radioactive sources.

Exploration of the burial apartments in tomb complex AS 68. Preliminary report of the 2013 fall season

Directory of Open Access Journals (Sweden)

Hana Vymazalová

2015-12-01

Full Text Available Exploration of the tomb complex of king’s daughter Sheretnebty, which was discovered in 2012, continued in the archaeological season of 2013. In October–November, the work concentrated on the underground parts of the tombs, including the burial shafts and burial chambers. In tomb AS 68c, two shafts were unusually deep; at a depth of 11.00 m under the ground the burial chambers of a man and a woman had been hewn. The man’s chamber contained a large sarcophagus of fine limestone and the remains of his burial and his tomb equipment, while the woman’s chamber remained largely unfinished and contained her rather simple burial placed on the floor. The so far discovered evidence indicates that this was the burial of Princess Sheretnebty. Another four shafts in the tomb contained four other burials of a female and three males, most probably the couple’s descendants. In addition, the shafts in the two western rock-cut tombs were explored. In the tomb of Shepespuptah (AS 68b, a single shaft was dug in the tomb’s chapel, while the tomb owner was buried in a burial chamber south of the chapel. The shaft in the chapel was large but reached only 1.40 m deep and was never finished and never used for burial. The two shafts in the tomb of Duaptah (AS 68a revealed the burials of two men; the southern shaft belonged to Duaptah himself while the northern shaft to a certain Nefermin. The burials were mostly very simple, and all of them were disturbed by tomb robbers. The preserved bones might, however, still reveal important details about the individuals buried in the rock-cut tombs, and they will therefore be studied in order to trace the family relationships among the tomb owners.

Closure certification report for the Bear Creek burial grounds B area and walk-in pits at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1994-06-01

On July 5, 1993, the revised RCRA Closure Plan for the Bear Creek Burial Grounds B Area and Walk-In Pits at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee, DOE/OR/01-1100 ampersand D3 and Y/ER-53 ampersand D3, was approved by the Tennessee Department of Environment and Conservation (TDEC). The closure activities described in that closure plan have been performed. The purpose of this document is to summarize the closure activities for B Area and Walk-In Pits (WIPs), including placement of the Kerr Hollow Quarry debris at the WIPs

Effect of phosphogypsum on workers and population's radiation exposure in vicinity of phosphogypsum waste burial site

International Nuclear Information System (INIS)

Othman, I.; Hushari, M.; Raja, G.; Sawaf, A.

1998-01-01

The phosphogypsum waste burial site was studied in more details of radiation viewpoint. This waste results from phosphate industry. The study covered ground water, nearby houses, air and emission rates of radon from this waste burial site. Results showed increasing of radiation exposure in the studied site and nearby area for both workers and population. Fortunately, this area was studied before instruction of the waste burial site. So it was easy to compare the new results with the previous ones and see the difference. Indoor radon concentration increased about 70%. Results also showed high emission rates which result in significant dose. The site needs continuous monitoring because the amount of phosphogypsum is increasing. Also groundwater should be monitored continuously to see the effect of the waste in the future if it happened. (author)

A model on valence state evaluation of TRU nuclides in reprocessing solutions

International Nuclear Information System (INIS)

Uchiyama, Gunzo; Fujine, Sachio; Yoshida, Zenko; Maeda, Mitsuru; Motoyama, Satoshi.

1998-02-01

A mathematical model was developed to evaluate the valence state of TRU nuclides in reprocessing process solutions. The model consists of mass balance equations, Nernst equations, reaction rate equations and electrically neutrality equations. The model is applicable for the valence state evaluation of TRU nuclides in both steady state and transient state conditions in redox equilibrium. The valence state which is difficult to measure under high radiation and multi component conditions is calculated by the model using experimentally measured data for the TRU nuclide concentrations, nitric acid and redox reagent concentrations, electrode potential and solution temperature. (author)

Physical and chemical feasibility of fueling molten salt reactors with TRU's trifluorides

International Nuclear Information System (INIS)

Ignatiev, V.; Feinberg, O.; Konakov, S.; Subbotine, S.; Surenkov, A.; Zakirov, R.

2001-01-01

The molten salt reactor (MSR) concept is very important for consideration as an element of future nuclear energy systems. These reactor systems are unique in many ways. Particularly, the MSRs appear to have substantial promise not only as advanced TRU free system operating in U-Th cycle, but also as transmuter of TRU. Physical and chemical feasibility of fueling MSR with TRU trifluorides is examined. Solvent compositions with and without U-Th as fissile / fertile addition are considered. The principle reactor and fuel cycle variables available for optimizing the performance of MSR as TRU transmuting system are discussed. These efforts led to the definition in minimal TRU mass flow rate, reduced total losses to waste and maximum possible burn up rate for the molten salt transmuter. The current status of technology and prospects for revisited interest are summarized. Significant chemical problems are remain to be resolved at the end of prior MSRs programs, notably, graphite life durability, tritium control, fate of noble metal fission products. Questions arising from plutonium and minor actinide fueling include: corrosion and container chemistry, new redox buffer for systems without uranium, analytical chemistry instrumentation, adequate constituent solubilities, suitable fuel processing and waste form development. However these problems appear to be soluble. (author)

Solidification of TRU wastes in a ceramic matrix

International Nuclear Information System (INIS)

Loida, A.; Schubert, G.

1991-01-01

Aluminumsilicate based ceramic materials have been evaluated as an alternative waste form for the incorporation of TRU wastes. These waste forms are free of water and - cannot generate hydrogen radiolyticly, - they show good compatibility between the compounds of the waste and the matrix, - they are resistent against aqueous solutions, heat and radiation. R and D-work has been performed to demonstrate the suitability of this waste form for the immobilization of TRU-wastes. Four kinds of original TRU-waste streams and a mixture of all of them have been immobilized by ceramization, using glove box and remote operation technique as well. Clay minerals, (kaolinite, bentonite) and reactive corundum were selected as ceramic raw materials (KAB 78) in an appropriate ratio yielding 78 wt% Al 2 O 3 and 22 wt%SiO 2 . The main process steps are (i) pretreatment of the liquid waste (concentration, denitration, neutralization, solid- liquid separation), (ii) mixing with ceramic raw materials and forming, (iii) heat treatment with T max. of 1300 0 C for 15 minutes. The waste load of the ceramic matrix has been increased gradually from 20 to 50, in some cases to 60 wt.%

Hydrogeologic investigation of the Maxey Flats radioactive waste burial site, Fleming County, Kentucky

Science.gov (United States)

Zehner, H.H.

1983-01-01

Burial trenches at the Maxey Flats radioactive waste burial site cover an area of about 20 acres, and are located on a plateau, about 300 to 400 feet above surrounding valleys. All waste is buried in the Nancy Member of the Borden Formation, and most is in the weathered shale (regolith) part of this member. Recharge to the rocks is probably by infiltration of rainfall through regolith at the top of the hill. At least two water tables are present: near the base of the regolith, at a depth of about 25 feet and; in the Ohio Shale, at a depth of about 300 feet. About 95 percent of ground-water discharge to streams is from colluvium on hillsides and valley alluvium. The remaining 5 percent is discharge from bedrock, of which about 0.5 percent is from rocks underlying the burial area. Waste radionuclides in the subsurface, other than tritium, were observed only in the regolith of the Nancy Member. Only tritium was observed with certainty in deeper rocks and in the adjacent valley alluvium. Other waste radionuclides were in streamwater and stream sediment, and may have been transported with overland runoff from the surface of the burial site. (USGS)

TRU drum corrosion task team report

Energy Technology Data Exchange (ETDEWEB)

Kooda, K.E.; Lavery, C.A.; Zeek, D.P.

1996-05-01

During routine inspections in March 1996, transuranic (TRU) waste drums stored at the Radioactive Waste Management Complex (RWMC) were found with pinholes and leaking fluid. These drums were overpacked, and further inspection discovered over 200 drums with similar corrosion. A task team was assigned to investigate the problem with four specific objectives: to identify any other drums in RWMC TRU storage with pinhole corrosion; to evaluate the adequacy of the RWMC inspection process; to determine the precise mechanism(s) generating the pinhole drum corrosion; and to assess the implications of this event for WIPP certifiability of waste drums. The task team investigations analyzed the source of the pinholes to be Hcl-induced localized pitting corrosion. Hcl formation is directly related to the polychlorinated hydrocarbon volatile organic compounds (VOCs) in the waste. Most of the drums showing pinhole corrosion are from Content Code-003 (CC-003) because they contain the highest amounts of polychlorinated VOCs as determined by headspace gas analysis. CC-001 drums represent the only other content code with a significant number of pinhole corrosion drums because their headspace gas VOC content, although significantly less than CC-003, is far greater than that of the other content codes. The exact mechanisms of Hcl formation could not be determined, but radiolytic and reductive dechlorination and direct reduction of halocarbons were analyzed as the likely operable reactions. The team considered the entire range of feasible options, ranked and prioritized the alternatives, and recommended the optimal solution that maximizes protection of worker and public safety while minimizing impacts on RWMC and TRU program operations.

TRU drum corrosion task team report

International Nuclear Information System (INIS)

Kooda, K.E.; Lavery, C.A.; Zeek, D.P.

1996-05-01

During routine inspections in March 1996, transuranic (TRU) waste drums stored at the Radioactive Waste Management Complex (RWMC) were found with pinholes and leaking fluid. These drums were overpacked, and further inspection discovered over 200 drums with similar corrosion. A task team was assigned to investigate the problem with four specific objectives: to identify any other drums in RWMC TRU storage with pinhole corrosion; to evaluate the adequacy of the RWMC inspection process; to determine the precise mechanism(s) generating the pinhole drum corrosion; and to assess the implications of this event for WIPP certifiability of waste drums. The task team investigations analyzed the source of the pinholes to be Hcl-induced localized pitting corrosion. Hcl formation is directly related to the polychlorinated hydrocarbon volatile organic compounds (VOCs) in the waste. Most of the drums showing pinhole corrosion are from Content Code-003 (CC-003) because they contain the highest amounts of polychlorinated VOCs as determined by headspace gas analysis. CC-001 drums represent the only other content code with a significant number of pinhole corrosion drums because their headspace gas VOC content, although significantly less than CC-003, is far greater than that of the other content codes. The exact mechanisms of Hcl formation could not be determined, but radiolytic and reductive dechlorination and direct reduction of halocarbons were analyzed as the likely operable reactions. The team considered the entire range of feasible options, ranked and prioritized the alternatives, and recommended the optimal solution that maximizes protection of worker and public safety while minimizing impacts on RWMC and TRU program operations

Los Alamos National Laboratory accelerated tru waste workoff strategies

International Nuclear Information System (INIS)

Kosiewicz, S.T.; Triay, I.R.; Rogers, P.Z.; Christensen, D.V.

1997-01-01

During 1996, the Los Alamos National Laboratory (LANL) developed two transuranic (TRU) waste workoff strategies that were estimated to save $270 - 340M through accelerated waste workoff and the elimination of a facility. The planning effort included a strategy to assure that LANL would have a significant quantity (3000+ drums) of TRU waste certified for shipment to the Waste Isolation Pilot Plant (WIPP) beginning in April of 1998, when WIPP was projected to open. One of the accelerated strategies can be completed in less than ten years through a Total Optimization of Parameters Scenario (open-quotes TOPSclose quotes). open-quotes TOPSclose quotes fully utilizes existing LANL facilities and capabilities. For this scenario, funding was estimated to be unconstrained at $23M annually to certify and ship the legacy inventory of TRU waste at LANL. With open-quotes TOPSclose quotes the inventory is worked off in about 8.5 years while shipping 5,000 drums per year at a total cost of $196M. This workoff includes retrieval from earthen cover and interim storage costs. The other scenario envisioned funding at the current level with some increase for TRUPACT II loading costs, which total $16M annually. At this funding level, LANL estimates it will require about 17 years to work off the LANL TRU legacy waste while shipping 2,500 drums per year to WIPP. The total cost will be $277M. This latter scenario decreases the time for workoff by about 19 years from previous estimates and saves an estimated $190M. In addition, the planning showed that a $70M facility for TRU waste characterization was not needed. After the first draft of the LANL strategies was written, Congress amended the WIPP Land Withdrawal Act (LWA) to accelerate the opening of WIPP to November 1997. Further, the No Migration Variance requirement for the WIPP was removed. This paper discusses the LANL strategies as they were originally developed. 1 ref., 3 figs., 2 tabs

Analisis Penerapan Metode Transmitter Receiver Unit (TRU Upgrading Untuk Mengatasi Traffic Congestion Jaringan GSM Pada BTS Area Purwokerto Kota

Directory of Open Access Journals (Sweden)

Alfin Hikmaturokhman

2011-05-01

Full Text Available Semakin banyaknya pengguna selular maka akan semakin banyak trafik yang akan tertampung. Trafik yang melebihi kapasitas kanal yang disediakan dapat menyebabkan kondisi Traffic Congestion. Untuk menanganinya diperlukan metode penambahan kapasitas kanal agar semua trafik dapat tertampung dengan baik. Metode ini disebut dengan TRU Upgrading. Transmitter Receiver Unit (TRU adalah hardware yang terletak pada Radio Base Station dalam BTS yang berisi slot-slot kanal sedangkan metode TRU Upgrading adalah metode dengan menambahkan/upgrade kapasitas kanal yang tersedia dari konfigurasi TRU yang telah ada sebelumnya, misalkan pada BTS Pabuaran memiliki konfigurasi 3x2x3 karena terjadi kejenuhan pelanggan maka konfigurasi TRU diupgrade menjadi 3x4x3. Perubahan konfigurasi TRU maka merubah konfigurasi BTS-nya serta menambah kapasitas kanalnya. Key Performance Indicator (KPI yang baik pada Indosat adalah menggunakan batas GoS 2%. Nilai GoS ini dikaitkan dengan tabel Erlang untuk mendapatkan sebuah nilai intensitas trafik. Jika nilai intensitas trafik konfigurasi TRU yang digunakan kurang dari nilai intensitas trafik pelanggan maka disebut traffic congestion. Sebagai akibat dari traffic congestion adalah kondisi blocking. TRU Upgrading ini dilakukan dengan harapan nilai blocking panggilan menjadi 0 %. Pada Purwokerto kota, diterapkan  TRU Upgrading untuk cell Grendeng 3, Pabuaran 2, dan Unsoed 1 karena trafik pelanggan yang terjadi melebihi nilai intensitas trafik dari konfigurasi TRU yang digunakan.   Untuk cell Unsoed 1 dan Grendeng 3 meski telah dilakukan TRU Upgrading menjadi 4 buah TRU tetap terjadi traffic congestion sebesar 8 sampai dengan 15 Erlang dikarenakan pada cell-cell ini mengcover area yang padat penduduk. Sedang untuk Pabuaran 2 penerapan TRU upgrading mencapai keefektifan sebesar 100%.

The making of urban ‘healtheries’: the transformation of cemeteries and burial grounds in late-Victorian East London☆

Science.gov (United States)

Brown, Tim

2013-01-01

This paper focuses on the conversion of disused burial grounds and cemeteries into gardens and playgrounds in East London from around the 1880s through to the end of the century. In addition to providing further empirical depth, especially relating to the work of philanthropic organisations such as the Metropolitan Public Gardens Association, the article brings into the foreground debates regarding the importance of such spaces to the promotion of the physical and moral health of the urban poor. Of particular note here is the recognition that ideas about the virtuous properties of open, green space were central to the success of attempts at social amelioration. In addition to identifying the importance of such ideas to the discourse of urban sanitary reformers, the paper considers the significance of less virtuous spaces to it; notably here, the street. Building on Driver's work on ‘moral environmentalism’ and Osborne and Rose's on ‘ethicohygienic space,’ this paper goes on to explore the significance of habit to the establishing of what Brabazon called ‘healtheries’ in late-Victorian East London. PMID:24882920

Development and application of new parameters for TRU transmutation effectiveness

International Nuclear Information System (INIS)

Han, Chi Young

2005-02-01

Four new parameters (incineration branching ratio, incineration rate, incineration time, and incineration buckling) have been developed to evaluate quantitatively the TRU transmutation effectiveness and applied to transmutation of uranium and TRU. From the incineration branching ratio, it is possible to analyze the main contributors to fission reaction for transmutation of a target nuclide. From the incineration rate, it is available to evaluate the transmutation effectiveness in the viewpoint of a relative incineration rate to incineration potential of a target nuclide and its family. This parameter is also used to calculate the incineration time and incineration buckling together with the incineration branching ratio. The incineration time makes it possible to discuss more practically the transmutation speed instead of the existing other parameters. The incineration buckling can be used to evaluate the time behavior of the incineration rate and also employed to support the results from the incineration time. Taking into account the transmutation effectiveness and potential of uranium and TRU derived by using the parameters and an existing neutron economy parameter, it was noted that the thermal neutron energy is very preferable from the transmutation effectiveness point of view, on the other hand the fast neutron energy is effective from the transmutation potential. Applying them to the typical critical and subcritical TRU burners, it is indicated that the critical reactor containing fertile uranium undergoes effectively the selective TRU transmutation on the present fast spectrum. It was also noted that the uranium-free subcritical reactor could be operated effectively on a little softer spectrum due to the larger neutron excess in the present spectrum. It is expected that the new parameters developed in this study and the results are directly applicable to practical transmutation reactor design, in particular accelerator-driven transmutation reactor

Test Plan: WIPP bin-scale CH TRU waste tests

International Nuclear Information System (INIS)

Molecke, M.A.

1990-08-01

This WIPP Bin-Scale CH TRU Waste Test program described herein will provide relevant composition and kinetic rate data on gas generation and consumption resulting from TRU waste degradation, as impacted by synergistic interactions due to multiple degradation modes, waste form preparation, long-term repository environmental effects, engineered barrier materials, and, possibly, engineered modifications to be developed. Similar data on waste-brine leachate compositions and potentially hazardous volatile organic compounds released by the wastes will also be provided. The quantitative data output from these tests and associated technical expertise are required by the WIPP Performance Assessment (PA) program studies, and for the scientific benefit of the overall WIPP project. This Test Plan describes the necessary scientific and technical aspects, justifications, and rational for successfully initiating and conducting the WIPP Bin-Scale CH TRU Waste Test program. This Test Plan is the controlling scientific design definition and overall requirements document for this WIPP in situ test, as defined by Sandia National Laboratories (SNL), scientific advisor to the US Department of Energy, WIPP Project Office (DOE/WPO). 55 refs., 16 figs., 19 tabs

Effect of phosphogypsum on workers and population's radiation exposure in vicinity of phosphogypsum waste burial site

International Nuclear Information System (INIS)

Othman, I.; Hushari, M.; Raja, G.; Sawaf, A.M.

1997-05-01

The phosphogypsum waste burial site was studied in more details of radiation viewpoint. This waste results from phosphate industry. The study covered ground water, nearby houses, air and emission rates of radon from this waste burial site. Results showed increasing of radiation exposure in the studied site and nearby area for both workers and population. Fortunately, this area was studied before instruction of the waste burial site. So it was easy to compare the new results with the previous ones and see the difference. Indoor radon concentration increased about 70%. Results also showed high emission rates which result in significant dose. The site needs continuous monitoring because the amount of phosphogypsum is increasing. Also groundwater should be monitored continuously to see the effect of the waste in the future if it happened. (author). 5 refs., 7 figs., 5 tabs

Hanford Site Transuranic (TRU) Waste Certification Plan

Energy Technology Data Exchange (ETDEWEB)

GREAGER, T.M.

1999-09-09

The Hanford Site Transuranic Waste Certification Plan establishes the programmatic framework and criteria within which the Hanford Site ensures that contract-handled TRU wastes can be certified as compliant with the WIPP WAC and TRUPACT-II SARP.

STRONTIUM & TRANSURANIC (TRU) SEPARATION PROCESS IN THE DOUBLE SHELL TANK (DST) SYSTEM

Energy Technology Data Exchange (ETDEWEB)

JOHNSON; SWANSON; BOECHLER

2005-06-10

The supernatants stored in tanks 241-AN-102 (AN-102) and 241-AN-107 (AN-107) contain soluble strontium-90 ({sup 90}Sr) and transuranic (TRU) elements that require removal prior to vitrification to comply with the Waste Treatment and Immobilization Plant (WTP) immobilized low-activity waste (ILAW) specification and with the 1997 agreement with the Nuclear Regulatory Commission on incidental waste. A precipitation process has been developed and tested with tank waste samples and simulants using strontium nitrate (Sr(NO{sub 3}){sub 2}) and sodium permanganate (NaMnO{sub 4}) to separate {sup 90}Sr and TRU from these wastes. This report evaluates removing Sr/TRU from AN-102 and AN-107 supernates in the DST system before delivery to the WTP. The in-tank precipitation is a direct alternative to the baseline WTP process, using the same chemical separations. Implementing the Sr/TRU separation in the DST system beginning in 2012 provides {approx}6 month schedule advantage to the overall mission, without impacting the mission end date or planned SST retrievals.

Leaching of solidified TRU-contaminated incinerator ash

International Nuclear Information System (INIS)

Fuhrmann, M.; Colombo, P.

1984-01-01

Leach rate and cumulative fractional releases of plutonium were determined for a series of laboratory-scale waste forms containing transuranic (TRU) contaminated incinerator ash. The solidification agents from which these waste forms were produced are commercially available materials for radioactive waste disposal. The leachants simulate groundwaters with chemical compositions that are indiginous to different geological media proposed for repositories. In this study TRU-contaminated ash was incorporated into waste forms fabricated with portland type I cement, urea-formaldehyde, polyester-styrene or Pioneer 221 bitumen. The ash was generated at the dual-chamber incinerator at the Rocky Flats Plant. These waste forms contained between 1.25 x 10 -2 and 4.4 x 10 -2 Ci (depending on the solidification agent) of mixed TRU isotopes comprised primarily of 239 Pu and 240 Pu. Five leachant solutions were prepared consisting of: (1) demineralized water, (2) simulated brine, (3) simplified sodium-dominated groundwater (30 meq NaCl/liter), (4) simplified calcium-dominated groundwater (30 meq CaCl 2 /liter), and (5) simplified bicarbonate-dominated groundwater (30 meq NaHCO 3 /liter). Cumulative fractional releases were found to vary significantly with different leachants and solidification agents. In all cases waste forms leached in brine gave the lowest leach rates. Urea-formaldehyde had the greatest release of radionuclides while polyester-styrene and portland cement had approximately equivalent fractional releases. Cement cured for 210 days retained radionuclides three times more effectively than cement cured only 30 days

Hanford Site Transuranic (TRU) Waste Certification Plan

International Nuclear Information System (INIS)

GREAGER, T.M.

1999-01-01

The Hanford Site Transuranic Waste Certification Plan establishes the programmatic framework and criteria with in which the Hanford Site ensures that contract-handled TRU wastes can be certified as compliant with the WIPP WAC and TRUPACT-II SARP

Guidelines for developing certification programs for newly generated TRU waste

International Nuclear Information System (INIS)

Whitty, W.J.; Ostenak, C.A.; Pillay, K.K.S.; Geoffrion, R.R.

1983-05-01

These guidelines were prepared with direction from the US Department of Energy (DOE) Transuranic (TRU) Waste Management Program in support of the DOE effort to certify that newly generated TRU wastes meet the Waste Isolation Pilot Plant (WIPP) Waste Acceptance Criteria. The guidelines provide instructions for generic Certification Program preparation for TRU-waste generators preparing site-specific Certification Programs in response to WIPP requirements. The guidelines address all major aspects of a Certification Program that are necessary to satisfy the WIPP Waste Acceptance Criteria and their associated Compliance Requirements and Certification Quality Assurance Requirements. The details of the major element of a Certification Program, namely, the Certification Plan, are described. The Certification Plan relies on supporting data and control documentation to provide a traceable, auditable account of certification activities. Examples of specific parts of the Certification Plan illustrate the recommended degree of detail. Also, a brief description of generic waste processes related to certification activities is included

A facility design for repackaging ORNL CH-TRU legacy waste in Building 3525

International Nuclear Information System (INIS)

Huxford, T.J.; Cooper, R.H. Jr.; Davis, L.E.; Fuller, A.B.; Gabbard, W.A.; Smith, R.B.; Guay, K.P.; Smith, L.C.

1995-07-01

For the last 25 years, the Oak Ridge National Laboratory (ORNL) has conducted operations which have generated solid, contact-handled transuranic (CH-TRU) waste. At present the CH-TRU waste inventory at ORNL is about 3400 55-gal drums retrievably stored in RCRA-permitted, aboveground facilities. Of the 3400 drums, approximately 2600 drums will need to be repackaged. The current US Department of Energy (DOE) strategy for disposal of these drums is to transport them to the Waste Isolation Pilot Plant (WIPP) in New Mexico which only accepts TRU waste that meets a very specific set of criteria documented in the WIPP-WAC (waste acceptance criteria). This report describes activities that were performed from January 1994 to May 1995 associated with the design and preparation of an existing facility for repackaging and certifying some or all of the CH-TRU drums at ORNL to meet the WIPP-WAC. For this study, the Irradiated Fuel Examination Laboratory (IFEL) in Building 3525 was selected as the reference facility for modification. These design activities were terminated in May 1995 as more attractive options for CH-TRU waste repackaging were considered to be available. As a result, this document serves as a final report of those design activities

Managing soil moisture on waste burial sites

International Nuclear Information System (INIS)

Anderson, J.E.; Ratzlaff, T.D.

1991-11-01

Shallow land burial is a common method of disposing of industrial, municipal, and low-level radioactive waste. The exclusion of water from buried wastes is a primary objective in designing and managing waste disposal sites. If wastes are not adequately isolated, water from precipitation may move through the landfill cover and into the wastes. The presence of water in the waste zone may promote the growth of plant roots to that depth and result in the transport of toxic materials to above-ground foliage. Furthermore, percolation of water through the waste zone may transport contaminants into ground water. This report presents results from a field study designed to assess the the potential for using vegetation to deplete soil moisture and prevent water from reaching buried wastes at the Idaho National Engineering Laboratory (INEL). Our results show that this approach may provide an economical means of limiting the intrusion of water on waste sites

Characterization of the Hanford 300 Area Burial Grounds. Task III: fluid transport and modeling

International Nuclear Information System (INIS)

Gee, G.W.; Simmons, C.S.

1979-08-01

In Task III, Fluid Transport and Modeling, a computer model was developed and applied to the 300 Area Burial Grounds to analyze the influence of potential evaporation and rainfall patterns on drainage. The model describes one-dimensional unsaturated flow. Fluid transport equations were evaluated to describe the driving forces of fluid flow. The data indicate that the major processes are evaporative drying, capillarity, and gravity flow. Thermally induced transport does not appear significant in the subsurface sediments of the area. Several empirical evaporation methods are available for assessing potential evaporation/evapotranspiration. Four methods were used with the unsaturated flow model. Ultimately, the Blaney-Criddle method was chosen for subsequent simulation examples because it relies only on the climatic data available and gave results comparable to the other methods tested. Simulations showed that a dry layer formation is important in controlling the soil-water balance in the profile. The surface dry layer acts as a mulch to retard the evaporative water losses and increase water storage. The most important climatic factor in determining drainage appears to be yearly rainfall distribution. When rainfall is distributed in fall or winter, during periods of low potential evaporation, both water storage and drainage are increased. Summer showers, on the other hand, were shown to add little to the annual water storage. Rainfall occurring in one year influences the subsequent annual drainage for several succeeding years because of annual changes in water storage capacity and the transient nature of unsaturated flow in the storage zone. 47 figures, 9 tables

Analysis of Chemical Composition of Non-Ferrous Metal Items from the Ananyino Burial Ground

Directory of Open Access Journals (Sweden)

Saprykina Irina А.

2016-03-01

Full Text Available The article presents results of an analysis conducted by the authors in order to study chemical composition of items from non-ferrous metals found on the Ananyino burial ground. A number of research methods, including OES, XRF and TXRF was applied to study a selection of 387 samples of arrow- and spearheads, celts, tail-pieces, warhammers, poleaxes, knives and daggers, as well as items of attire and jewelry, some sporadic details of harness and bridle. The fi ndings are quite comparable. The results were classifi ed by the geochemical principle of 1,0% alloyage threshold. It was found out that the sample primarily consists of copper items, including “pure” copper and copper with a wide range of trace elements (particularly, Ni, As, Sb. The core (48% consists of copper items with traces of antimony and arsenic, or “pure” copper (7%, tin or triple bronze (40%; it also includes some other types of alloys based on copper or silver (5%. As the analysis has shown, complex ores seem to be the most probable source of copper. Traditionally, the Urals, the Sayan and the Altay Mountains, Kazakhstan and the Northern Caucasus were regarded as the most probable minefi elds to supply ores to the barren regions of Eastern Europe. While ore sources for products made of metallurgical “pure” copper are localized within the Ural mining and metallurgical region, metal sources for items cast from different groups of alloys (rather than imports of ready-made products require further research.

Effect of phosphogypsum on workers and population`s radiation exposure in vicinity of phosphogypsum waste burial site

Energy Technology Data Exchange (ETDEWEB)

Othman, I; Hushari, M; Raja, G; Sawaf, A M [Atomic Energy Commission, Dept. of Radiation Protection and Nuclear Safety, Damascus (Syrian Arab Republic)

1997-05-01

The phosphogypsum waste burial site was studied in more details of radiation viewpoint. This waste results from phosphate industry. The study covered ground water, nearby houses, air and emission rates of radon from this waste burial site. Results showed increasing of radiation exposure in the studied site and nearby area for both workers and population. Fortunately, this area was studied before instruction of the waste burial site. So it was easy to compare the new results with the previous ones and see the difference. Indoor radon concentration increased about 70%. Results also showed high emission rates which result in significant dose. The site needs continuous monitoring because the amount of phosphogypsum is increasing. Also groundwater should be monitored continuously to see the effect of the waste in the future if it happened. (author). 5 refs., 7 figs., 5 tabs.

Thermodynamic Modeling of Sr/TRU Removal

International Nuclear Information System (INIS)

Felmy, A.R.

2000-01-01

This report summarizes the development and application of a thermodynamic modeling capability designed to treat the Envelope C wastes containing organic complexants. A complete description of the model development is presented. In addition, the model was utilized to help gain insight into the chemical processes responsible for the observed levels of Sr, TRU, Fe, and Cr removal from the diluted feed from tank 241-AN-107 which had been treated with Sr and permanganate. Modeling results are presented for Sr, Nd(III)/Eu(III), Fe, Cr, Mn, and the major electrolyte components of the waste (i.e. NO 3 , NO 2 , F,...). On an overall basis the added Sr is predicted to precipitate as SrCO 3 (c) and the MnO 4 - reduced by the NO 2 - and precipitated as a Mn oxide. These effects result in only minor changes to the bulk electrolyte chemistry, specifically, decreases in NO 2 - and CO 3 2- , and increases in NO 3 - and OH - . All of these predictions are in agreement with the experimental observations. The modeling also indicates that the majority of the Sr, TRU's (or Nd(III)/Eu(III)) analogs, and Fe are tied up with the organic complexants. The Sr and permanganate additions are not predicted to effect these chelate complexes significantly owing to the precipitation of insoluble Mn oxides or SrCO 3 . These insoluble phases maintain low dissolved concentrations of Mn and Sr which do not affect any of the other components tied up with the complexants. It appears that the removal of the Fe and TRU'S during the treatment process is most likely as a result of adsorption or occlusion on/into the Mn oxides or SrCO 3 , not as direct displacement from the complexants into precipitates. Recommendations are made for further studies that are needed to help resolve these issues

Repackaging SRS Black Box TRU Waste

International Nuclear Information System (INIS)

Swale, D. J.; Stone, K.A.; Milner, T. N.

2006-01-01

Historically, large items of TRU Waste, which were too large to be packaged in drums for disposal have been packaged in various sizes of custom made plywood boxes at the Savannah River Site (SRS), for many years. These boxes were subsequently packaged into large steel ''Black Boxes'' for storage at SRS, pending availability of Characterization and Certification capability, to facilitate disposal of larger items of TRU Waste. There are approximately 107 Black Boxes in inventory at SRS, each measuring some 18' x 12' x 7', and weighing up to 45,000 lbs. These Black Boxes have been stored since the early 1980s. The project to repackage this waste into Standard Large Boxes (SLBs), Standard Waste Boxes (SWB) and Ten Drum Overpacks (TDOP), for subsequent characterization and WIPP disposal, commenced in FY04. To date, 10 Black Boxes have been repackaged, resulting in 40 SLB-2's, and 37 B25 overpack boxes, these B25's will be overpacked in SLB-2's prior to shipping to WIPP. This paper will describe experience to date from this project

Documentation of TRU biological transport model (BIOTRAN)

Energy Technology Data Exchange (ETDEWEB)

Gallegos, A.F.; Garcia, B.J.; Sutton, C.M.

1980-01-01

Inclusive of Appendices, this document describes the purpose, rationale, construction, and operation of a biological transport model (BIOTRAN). This model is used to predict the flow of transuranic elements (TRU) through specified plant and animal environments using biomass as a vector. The appendices are: (A) Flows of moisture, biomass, and TRU; (B) Intermediate variables affecting flows; (C) Mnemonic equivalents (code) for variables; (D) Variable library (code); (E) BIOTRAN code (Fortran); (F) Plants simulated; (G) BIOTRAN code documentation; (H) Operating instructions for BIOTRAN code. The main text is presented with a specific format which uses a minimum of space, yet is adequate for tracking most relationships from their first appearance to their formulation in the code. Because relationships are treated individually in this manner, and rely heavily on Appendix material for understanding, it is advised that the reader familiarize himself with these materials before proceeding with the main text.

Documentation of TRU biological transport model (BIOTRAN)

International Nuclear Information System (INIS)

Gallegos, A.F.; Garcia, B.J.; Sutton, C.M.

1980-01-01

Inclusive of Appendices, this document describes the purpose, rationale, construction, and operation of a biological transport model (BIOTRAN). This model is used to predict the flow of transuranic elements (TRU) through specified plant and animal environments using biomass as a vector. The appendices are: (A) Flows of moisture, biomass, and TRU; (B) Intermediate variables affecting flows; (C) Mnemonic equivalents (code) for variables; (D) Variable library (code); (E) BIOTRAN code (Fortran); (F) Plants simulated; (G) BIOTRAN code documentation; (H) Operating instructions for BIOTRAN code. The main text is presented with a specific format which uses a minimum of space, yet is adequate for tracking most relationships from their first appearance to their formulation in the code. Because relationships are treated individually in this manner, and rely heavily on Appendix material for understanding, it is advised that the reader familiarize himself with these materials before proceeding with the main text

Radionuclides in a deciduous forest surrounding a shallow-land-burial site in the eastern United States

International Nuclear Information System (INIS)

Rickard, W.H.; Kirby, L.J.; McShane, M.C.

1981-06-01

The objective of this study was to determine if radioactive materials buried in trenches at the Maxey Flats burial ground in eastern Kentucky have migrated into the surrounding oak-hickory forest. Forest floor litter, minearl soil, and tree leaves were sampled and the radionuclide content measured

Shallow land burial of solid low-level radioactive wastes - 30 years of experience at the Savannah River Plant

International Nuclear Information System (INIS)

Stone, J.A.; Fenimore, J.W.; Hawkins, R.H.; Oblath, S.B.; Ryan, J.P. Jr.

1983-01-01

Solid radioactive wastes from production of nuclear materials at the Savannah River Plant (SRP) are buried in shallow trenches on a 79-hectare plot within the SRP site. The SRP burial ground, in use since 1953, has provided containment for about 370,000 m 3 of waste containing 10 7 Ci that have been buried through 1982. Site characteristics, operating practices, and monitoring results are described. Extensive field and laboratory studies aimed at developing a fundamental understanding of the soil/waste/water system of the SRP burial ground are discussed. Leaching and migration of buried radionuclides have been monitored by assays of soil cores and by periodic sampling of numerous groundwater wells. Except for tritium, none of the radionuclides have migrated significantly from the waste. Generally, traces of alpha and nonvolatile beta/gamma emitters that have entered the groundwater can be detected only by ultra-low-level radiochemical analyses. Current research efforts include: (1) migration of individual radionuclides such as 60 Co, 90 Sr, 99 Tc, 106 Ru, 129 I, 137 Cs, 238 Pu, and 239 Pu (plus nonradioactive materials such as mercury); (2) groundwater chemistry under buried waste, to determine fundamental transport mechanisms; (3) radionuclide migration from well characteized sources emplaced in lysimeters; (4) laboratory measurements of sorption on burial ground soil. In addition to ensuring continued safe operation, the ongoing waste migration studies provide technical guidance for site operations and decommissioning

TRU waste certification and TRUPACT-2 payload verification

International Nuclear Information System (INIS)

Hunter, E.K.; Johnson, J.E.

1990-01-01

The Waste Isolation Pilot Plant (WIPP) established a policy that requires each waste shipper to verify that all waste shipments meet the requirements of the Waste Acceptance Criteria (WAC) prior to being shipped. This verification provides assurance that transuranic (TRU) wastes meet the criteria while still retained in a facility where discrepancies can be immediately corrected. Each Department of Energy (DOE) TRU waste facility planning to ship waste to the Waste Isolation Pilot Plant (WIPP) is required to develop and implement a specific program including Quality Assurance (QA) provisions to verify that waste is in full compliance with WIPP's WAC. This program is audited by a composite DOE and contractor audit team prior to granting the facility permission to certify waste. During interaction with the Nuclear Regulatory Commission (NRC) on payload verification for shipping in TRUPACT-II, a similar system was established by DOE. The TRUPACT-II Safety Analysis Report (SAR) contains the technical requirements and physical and chemical limits that payloads must meet (like the WAC). All shippers must plan and implement a payload control program including independent QA provisions. A similar composite audit team will conduct preshipment audits, frequent subsequent audits, and operations inspections to verify that all TRU waste shipments in TRUPACT-II meet the requirements of the Certificate of Compliance issued by the NRC which invokes the SAR requirements. 1 fig

TRU Waste Management Program. Cost/schedule optimization analysis

International Nuclear Information System (INIS)

Detamore, J.A.; Raudenbush, M.H.; Wolaver, R.W.; Hastings, G.A.

1985-10-01

This Current Year Work Plan presents in detail a description of the activities to be performed by the Joint Integration Office Rockwell International (JIO/RI) during FY86. It breaks down the activities into two major work areas: Program Management and Program Analysis. Program Management is performed by the JIO/RI by providing technical planning and guidance for the development of advanced TRU waste management capabilities. This includes equipment/facility design, engineering, construction, and operations. These functions are integrated to allow transition from interim storage to final disposition. JIO/RI tasks include program requirements identification, long-range technical planning, budget development, program planning document preparation, task guidance development, task monitoring, task progress information gathering and reporting to DOE, interfacing with other agencies and DOE lead programs, integrating public involvement with program efforts, and preparation of reports for DOE detailing program status. Program Analysis is performed by the JIO/RI to support identification and assessment of alternatives, and development of long-term TRU waste program capabilities. These analyses include short-term analyses in response to DOE information requests, along with performing an RH Cost/Schedule Optimization report. Systems models will be developed, updated, and upgraded as needed to enhance JIO/RI's capability to evaluate the adequacy of program efforts in various fields. A TRU program data base will be maintained and updated to provide DOE with timely responses to inventory related questions

Basic study on decontamination of TRU wastes with cerium mediated electrolytic oxidation method

International Nuclear Information System (INIS)

Ishii, Junichi; Kobayashi, Fuyumi; Uchida, Shoji; Sumiya, Masato; Kida, Takashi; Shirahashi, Koichi; Umeda, Miki; Sakuraba, Koichi

2010-03-01

At Nuclear Fuel Cycle Safety Engineering Research Facility (NUCEF), the cerium mediated electrolytic oxidation method which is a decontamination technique to decrease the radioactivity of TRU wastes to the clearance-level has been developed for the effective reduction of TRU wastes generated from the decommissioning of a nuclear fuel reprocessing facility and so on. This method corrodes the oxide layer and the surface of metallic TRU metal wastes by the strong oxidation power of Ce 4+ in nitric acid. In this study, parameter tests were conducted to optimize the solution condition of Ce 3+ initial concentrations and nitric acid concentrations. The target corrosion rate of metallic TRU wastes set to be 2 - 4 μm/h for the practical use of this method. Under the optimized solution condition, a dissolution test of stainless steel simulating wastes was carried out. From the result of the dissolution test, the average corrosion rate was 3.3 μm/h during the test time of 90 hours. Based on the supposition that the corrosion depth of metallic TRU wastes was 20 μm enough to achieve the clearance-level, the treatment time for the decontamination was about 6 hours. It was confirmed from the result that the decontamination could be performed within one day and the decontamination solution could repeatedly reuse 15 times. (author)

Decontamination of TRU glove boxes

International Nuclear Information System (INIS)

Crawford, J.H.

1978-03-01

Two glove boxes that had been used for work with transuranic nuclides (TRU) for about 12 years were decontaminated in a test program to collect data for developing a decontamination facility for large equipment highly contaminated with alpha emitters. A simple chemical technique consisting of a cycle of water flushes and alkaline permanganate and oxalic acid washes was used for both boxes. The test showed that glove boxes and similar equipment that are grossly contaminated with transuranic nuclides can be decontaminated to the current DIE nonretrievable disposal guide of <10 nCi TRU/g with a moderate amount of decontamination solution and manpower. Decontamination of the first box from an estimated 1.3 Ci to about 5 mCi (6 nCi/g) required 1.3 gallons of decontamination solution and 0.03 man-hour of work for each square foot of surface area. The second box was decontaminated from an estimated 3.4 Ci to about 2.8 mCi (4.2 nCi/g) using 0.9 gallon of decontamination solution and 0.02 man-hour for each square foot of surface area. Further reductions in contamination were achieved by repetitive decontamination cycles, but the effectiveness of the technique decreased sharply after the initial cycle

Waste Isolation Pilot Plant RH TRU waste preoperational checkout: Final report

International Nuclear Information System (INIS)

1988-06-01

This report documents the results of the Waste Isolation Pilot Plant (WIPP) Remote-Handled Transuranic (RH TRU) Waste Preoperational Checkout. The primary objective of this checkout was to demonstrate the process of handling RH TRU waste packages, from receipt through emplacement underground, using equipment, personnel, procedures, and methods to be used with actual waste packages. A further objective was to measure operational time lines to provide bases for confirming the WIPP design through put capability and for projecting operator radiation doses. Successful completion of this checkout is a prerequisite to the receipt of actual RH TRU waste. This checkout was witnessed in part by members of the Environmental Evaluation Group (EEG) of the state of New Mexico. Further, this report satisfies a key milestone contained in the Agreement for Consultation and Cooperation with the state of New Mexico. 4 refs., 26 figs., 4 tabs

MWIR-1995 DOE national mixed and TRU waste database users guide

International Nuclear Information System (INIS)

1995-11-01

The Department of Energy (DOE) National 1995 Mixed Waste Inventory Report (MWIR-1995) Database Users Guide provides information on computer system requirements and describes installation, operation, and navigation through the database. The MWIR-1995 database contains a detailed, nationwide compilation of information on DOE mixed waste streams and treatment systems. In addition, the 1995 version includes data on non- mixed, transuranic (TRU) waste streams. These were added to the data set as a result of coordination of the 1995 update with the National Transuranic Program Office's (NTPO's) data needs to support the Waste Isolation Pilot Plant (WIPP) TRU Waste Baseline Inventory Report (WTWBIR). However, the information on the TRU waste streams is limited to that associated with the core mixed waste data requirements. The additional, non-core data on TRU streams collected specifically to support the WTWBIR is not included in the MWIR-1995 database. With respect to both the mixed and TRU waste stream data, the data set addresses open-quotes storedclose quotes streams. In this instance, open-quotes storedclose quotes streams are defined as (a) streams currently in storage at both EM-30 and EM-40 sites and (b) streams that have yet to be generated but are anticipated within the next five years from sources other than environmental restoration and decontamination and decommissioning (ER/D ampersand D) activities. Information on future ER/D ampersand D streams is maintained in the EM-40 core database. The MWIR-1995 database also contains limited information for both waste streams and treatment systems that have been removed or deleted since the 1994 MWIR. Data on these is maintained only through Section 2, Waste Stream Identification/Tracking/Source, to document the reason for removal from the data set

Urban Stream Burial Increases Watershed-Scale Nitrate Export.

Directory of Open Access Journals (Sweden)

Jake J Beaulieu

Full Text Available Nitrogen (N uptake in streams is an important ecosystem service that reduces nutrient loading to downstream ecosystems. Here we synthesize studies that investigated the effects of urban stream burial on N-uptake in two metropolitan areas and use simulation modeling to scale our measurements to the broader watershed scale. We report that nitrate travels on average 18 times farther downstream in buried than in open streams before being removed from the water column, indicating that burial substantially reduces N uptake in streams. Simulation modeling suggests that as burial expands throughout a river network, N uptake rates increase in the remaining open reaches which somewhat offsets reduced N uptake in buried reaches. This is particularly true at low levels of stream burial. At higher levels of stream burial, however, open reaches become rare and cumulative N uptake across all open reaches in the watershed rapidly declines. As a result, watershed-scale N export increases slowly at low levels of stream burial, after which increases in export become more pronounced. Stream burial in the lower, more urbanized portions of the watershed had a greater effect on N export than an equivalent amount of stream burial in the upper watershed. We suggest that stream daylighting (i.e., uncovering buried streams can increase watershed-scale N retention.

Characterizing cemented TRU waste for RCRA hazardous constituents

International Nuclear Information System (INIS)

Yeamans, D.R.; Betts, S.E.; Bodenstein, S.A.

1996-01-01

Los Alamos National Laboratory (LANL) has characterized drums of solidified transuranic (TRU) waste from four major waste streams. The data will help the State of New Mexico determine whether or not to issue a no-migration variance of the Waste Isolation Pilot Plant (WIPP) so that WIPP can receive and dispose of waste. The need to characterize TRU waste stored at LANL is driven by two additional factors: (1) the LANL RCRA Waste Analysis Plan for EPA compliant safe storage of hazardous waste; (2) the WIPP Waste Acceptance Criteria (WAC) The LANL characterization program includes headspace gas analysis, radioassay and radiography for all drums and solids sampling on a random selection of drums from each waste stream. Data are presented showing that the only identified non-metal RCRA hazardous component of the waste is methanol

Study on characteristics of spent PWR cladding hull for categorizing into Non-TRU waste

International Nuclear Information System (INIS)

Jung, In Ha; Kim, Jong Ho; Park, Jang Jin; Shin, Jin Myeong; Lee, Ho Hee; Yang, Myung Seung

2005-01-01

AFCI and GEN-IV programs aim for decreasing the high level radioactive wastes to be disposed. They also try to get valuable materials to recycle as resources such as uranium and plutonium. On the other hand, cladding hull expected to be one-thirds in volume of spent fuel assembly has not studied so much in the point view of recycling to reuse. Since traditional process of reprocessing was wet process, cladding hull generating through the reprocessing process was unavoidably contaminated with TRU by acid solvent during the process. Therefore, cladding hull has been classified into TRU wastes or high level wastes. According to the strategy for TRU high level radioactive wastes of USA as well as Korea, it regulates in two respects. One is activity and the other is heat generation. In respect of activity, TRU waste contains more than 100 nCi/kg of alpha emits with longer half life than 20 years and higher than 92 in atomic number. Also, wastes are categorized into TRU waste when it generates higher than 2kW/m3, in the respect of heat generation. Our results as well as literatures, almost all of TRU nuclides in the cladding hull are responsible for remained uranium and plutonium owing to pellet-cladding interaction. In addition, recoiled fission products on the surface of the cladding hull serve as heat generator. Up to now, decontamination of the cladding hull generating from the reprocessing of wet process is regarded as valueless and un-economic works owing to the amount of second waste produced

Waste Isolation Pilot Plant simulated RH TRU waste experiments: Data and interpretation pilot

International Nuclear Information System (INIS)

Molecke, M.A.; Argueello, G.J.; Beraun, R.

1993-04-01

The simulated, i.e., nonradioactive remote-handled transuranic waste (RH TRU) experiments being conducted underground in the Waste Isolation Pilot Plant (WIPP) were emplaced in mid-1986 and have been in heated test operation since 9/23/86. These experiments involve the in situ, waste package performance testing of eight full-size, reference RH TRU containers emplaced in horizontal, unlined test holes in the rock salt ribs (walls) of WIPP Room T. All of the test containers have internal electrical heaters; four of the test emplacements were filled with bentonite and silica sand backfill materials. We designed test conditions to be ''near-reference'' with respect to anticipated thermal outputs of RH TRU canisters and their geometrical spacing or layout in WIPP repository rooms, with RH TRU waste reference conditions current as of the start date of this test program. We also conducted some thermal overtest evaluations. This paper provides a: detailed test overview; comprehensive data update for the first 5 years of test operations; summary of experiment observations; initial data interpretations; and, several status; experimental objectives -- how these tests support WIPP TRU waste acceptance, performance assessment studies, underground operations, and the overall WIPP mission; and, in situ performance evaluations of RH TRU waste package materials plus design details and options. We provide instrument data and results for in situ waste container and borehole temperatures, pressures exerted on test containers through the backfill materials, and vertical and horizontal borehole-closure measurements and rates. The effects of heat on borehole closure, fracturing, and near-field materials (metals, backfills, rock salt, and intruding brine) interactions were closely monitored and are summarized, as are assorted test observations. Predictive 3-dimensional thermal and structural modeling studies of borehole and room closures and temperature fields were also performed

CONCRETE CONTAINERS FOR LONG TERM STORAGE AND FINAL DISPOSAL OF TRU WASTE AND LONG LIVED ILW

International Nuclear Information System (INIS)

Sakamoto, H.; Asano, H.; Tunaboylu, K.; Mayer, G.; Klubertanz, G.; Kobayashi, S.; Komuro, T.; Wagner, E.

2003-01-01

Transuranic (TRU) waste packaging development has been conducted since 1998 by the Radioactive Waste Management Funding and Research Centre (RWMC) to support the TRU waste disposal concept in Japan. In this paper, the overview of development status of the reinforced concrete package is introduced. This package has been developed in order to satisfy the Japanese TRU waste disposal concept based on current technology and to provide a low cost package. Since 1998, the basic design work (safety evaluation, manufacturing and handling procedure, economic evaluation, elemental tests etc.) have been carried out. As a result, the basic specification of the package was decided. This report presents the concept as well as the results of basic design, focused on safety analysis and handling procedure of the package. Two types of the packages exist: - Package-A: for non-heat generating TRU waste from reprocessing in 200 l drums and - Package-B: for heat generating TRU-waste from reprocessing

Automated, simple, and efficient influenza RNA extraction from clinical respiratory swabs using TruTip and epMotion.

Science.gov (United States)

Griesemer, Sara B; Holmberg, Rebecca; Cooney, Christopher G; Thakore, Nitu; Gindlesperger, Alissa; Knickerbocker, Christopher; Chandler, Darrell P; St George, Kirsten

2013-09-01

Rapid, simple and efficient influenza RNA purification from clinical samples is essential for sensitive molecular detection of influenza infection. Automation of the TruTip extraction method can increase sample throughput while maintaining performance. To automate TruTip influenza RNA extraction using an Eppendorf epMotion robotic liquid handler, and to compare its performance to the bioMerieux easyMAG and Qiagen QIAcube instruments. Extraction efficacy and reproducibility of the automated TruTip/epMotion protocol was assessed from influenza-negative respiratory samples spiked with influenza A and B viruses. Clinical extraction performance from 170 influenza A and B-positive respiratory swabs was also evaluated and compared using influenza A and B real-time RT-PCR assays. TruTip/epMotion extraction efficacy was 100% in influenza virus-spiked samples with at least 745 influenza A and 370 influenza B input gene copies per extraction, and exhibited high reproducibility over four log10 concentrations of virus (extraction were also positive following TruTip extraction. Overall Ct value differences obtained between TruTip/epMotion and easyMAG/QIAcube clinical extracts ranged from 1.24 to 1.91. Pairwise comparisons of Ct values showed a high correlation of the TruTip/epMotion protocol to the other methods (R2>0.90). The automated TruTip/epMotion protocol is a simple and rapid extraction method that reproducibly purifies influenza RNA from respiratory swabs, with comparable efficacy and efficiency to both the easyMAG and QIAcube instruments. Copyright © 2013 Elsevier B.V. All rights reserved.

Development of an Alternative Treatment Scheme for Sr/TRU Removal: Permanganate Treatment of AN-107 Waste

International Nuclear Information System (INIS)

Hallen, R.T.; Bryan, S.A.; Hoopes, F.V.

2000-01-01

A number of Hanford tanks received waste containing organic complexants, which increase the volubility of Sr-90 and transuranic (TRU) elements. Wastes from these tanks require additional pretreatment to remove Sr-90 and TRU for immobilization as low activity waste (Waste Envelope C). The baseline pretreatment process for Sr/TRU removal was isotopic exchange and precipitation with added strontium and iron. However, studies at both Battelle and Savannah River Technology Center (SRTC) have shown that the Sr/Fe precipitates were very difficult to filter. This was a result of the formation of poor filtering iron solids. An alternate treatment technology was needed for Sr/TRU removal. Battelle had demonstrated that permanganate treatment was effective for decontaminating waste samples from Hanford Tank SY-101 and proposed that permanganate be examined as an alternative Sr/TRU removal scheme for complexant-containing tank wastes such as AW107. Battelle conducted preliminary small-scale experiments to determine the effectiveness of permanganate treatment with AN-107 waste samples that had been archived at Battelle from earlier studies. Three series of experiments were performed to evaluate conditions that provided adequate Sr/TRU decontamination using permanganate treatment. The final series included experiments with actual AN-107 diluted feed that had been obtained specifically for BNFL process testing. Conditions that provided adequate Sr/TRU decontamination were identified. A free hydroxide concentration of 0.5M provided adequate decontamination with added Sr of 0.05M and permanganate of 0.03M for archived AN-107. The best results were obtained when reagents were added in the sequence Sr followed by permanganate with the waste at ambient temperature. The reaction conditions for Sr/TRU removal will be further evaluated with a 1-L batch of archived AN-107, which will provide a large enough volume of waste to conduct crossflow filtration studies (Hallen et al. 2000a)

Development of an Alternative Treatment Scheme for Sr/TRU Removal: Permanganate Treatment of AN-107 Waste

Energy Technology Data Exchange (ETDEWEB)

RT Hallen; SA Bryan; FV Hoopes

2000-08-04

A number of Hanford tanks received waste containing organic complexants, which increase the volubility of Sr-90 and transuranic (TRU) elements. Wastes from these tanks require additional pretreatment to remove Sr-90 and TRU for immobilization as low activity waste (Waste Envelope C). The baseline pretreatment process for Sr/TRU removal was isotopic exchange and precipitation with added strontium and iron. However, studies at both Battelle and Savannah River Technology Center (SRTC) have shown that the Sr/Fe precipitates were very difficult to filter. This was a result of the formation of poor filtering iron solids. An alternate treatment technology was needed for Sr/TRU removal. Battelle had demonstrated that permanganate treatment was effective for decontaminating waste samples from Hanford Tank SY-101 and proposed that permanganate be examined as an alternative Sr/TRU removal scheme for complexant-containing tank wastes such as AW107. Battelle conducted preliminary small-scale experiments to determine the effectiveness of permanganate treatment with AN-107 waste samples that had been archived at Battelle from earlier studies. Three series of experiments were performed to evaluate conditions that provided adequate Sr/TRU decontamination using permanganate treatment. The final series included experiments with actual AN-107 diluted feed that had been obtained specifically for BNFL process testing. Conditions that provided adequate Sr/TRU decontamination were identified. A free hydroxide concentration of 0.5M provided adequate decontamination with added Sr of 0.05M and permanganate of 0.03M for archived AN-107. The best results were obtained when reagents were added in the sequence Sr followed by permanganate with the waste at ambient temperature. The reaction conditions for Sr/TRU removal will be further evaluated with a 1-L batch of archived AN-107, which will provide a large enough volume of waste to conduct crossflow filtration studies (Hallen et al. 2000a).

Soil monitoring instrumentation

International Nuclear Information System (INIS)

Umbarger, C.J.

1981-01-01

The Los Alamos Scientific Laboratory (LASL) has an extensive program for the development of nondestructive assay instrumentation for the quantitative analysis of transuranic (TRU) materials found in bulk solid wastes generated by Department of Energy facilities and by the commercial nuclear power industry. Included are wastes generated in decontamination and decommissioning of outdated nuclear facilities, as well as from old waste-burial-ground exhumation programs. The assay instrumentation is designed to have detection limits below 10 nCi/g wherever practicable. The assay instrumentation that is applied specifically to soil monitoring is discussed

Progress report on disposal concept for TRU waste in Japan

International Nuclear Information System (INIS)

2000-03-01

The object of this report is to contribute towards establishing a national TRU waste disposal program by integrating the results of research and development work carried out by JNC and the electricity utilities and summarizing the findings concerning safe methods for TRU waste disposal. The report consists of 5 chapters: the first describes the boundary conditions for the review of the TRU waste disposal concept (including geological conditions) and the basic concept adopted; the second describes the generation and characteristics of TRU waste and the third outlines the disposal technology; the fourth gives the key of the safety assessment and the fifth presents the conclusions of the report and lists issues for future consideration. The geological environment of Japan is simply classified into crystalline and sedimentary rock types (in terms of groundwater flow properties and rock strength) and a set of target conditions/properties for each rock type is then established. Based on this, a case which represents the basis for performance assessment (the reference case) will be defined. Alternatives to the reference case are studied to investigate the flexibility of the disposal concept. Under the conditions assumed in this study, the perturbing events considered showed no significant effects on the dose at the 100 meter evaluation point, owing to the relatively high efficiency of the natural barrier. However, the significant effect of these events on nuclide from the EBS shows that, in the case of a less efficient natural barrier, their effects could influence resulting dose. (S.Y.)

A comparative neutronic analysis of 150MWe TRU burner according to the coolant alteration

International Nuclear Information System (INIS)

Yoo, J. W.; Kim, S. J.; Kim, Y. I.

2000-01-01

A comparative neutronic analysis has been conducted for the small TRU burner according to their coolant material. The use of Pb-Bi coolant gave a low burnup reactivity swing and negative or less positive coolant void coefficient with harder neutron spectrum. By a lower burnup reactivity swing and higher conversion ratio of Pb-Bi cooled core, the total amount of TRU consumption was found to be small compared with Na cooled core despite of the higher MA consumption ratio of Pb-Bi cooled core. However, Pb-Bi cooled reactor have a lager margin in the coolant void coefficient, so that a variable MA composition can be loaded in the core. Accordingly, even though the Pb-Bi cooled TRU burner has not effectiveness on TRU burning in the same geometry and material condition, a flexible MA loading is envisaged to result in 10 times larger MA burning amount, still preserving a low coolant void worth

MSFR TRU-burning potential and comparison with an SFR

Energy Technology Data Exchange (ETDEWEB)

Fiorina, C.; Cammi, A. [Politecnico di Milano: Via La Masa 34, 20136 Milan (Italy); Franceschini, F. [Westinghouse Electric Company LL: 1000 Westinghouse Dr., Cranberry Township, PA 16066 (United States); Krepel, J. [Paul Scherrer Institut - PSI WEST, 5234 Villigen (Switzerland)

2013-07-01

The objective of this work is to evaluate the Molten Salt Fast Reactor (MSFR) potential benefits in terms of transuranics (TRU) burning through a comparative analysis with a sodium-cooled FR. The comparison is based on TRU- and MA-burning rates, as well as on the in-core evolution of radiotoxicity and decay heat. Solubility issues limit the TRU-burning rate to 1/3 that achievable in traditional low-CR FRs (low-Conversion-Ratio Fast Reactors). The softer spectrum also determines notable radiotoxicity and decay heat of the equilibrium actinide inventory. On the other hand, the liquid fuel suggests the possibility of using a Pu-free feed composed only of Th and MA (Minor Actinides), thus maximizing the MA burning rate. This is generally not possible in traditional low-CR FRs due to safety deterioration and decay heat of reprocessed fuel. In addition, the high specific power and the lack of out-of-core cooling times foster a quick transition toward equilibrium, which improves the MSFR capability to burn an initial fissile loading, and makes the MSFR a promising system for a quick (i.e., in a reactor lifetime) transition from the current U-based fuel cycle to a novel closed Th cycle. (authors)

TRU-ART: A cost-effective prototypical neutron imaging technique for transuranic waste certification systems

International Nuclear Information System (INIS)

Horton, W.S.

1989-01-01

The certification of defense radioactive waste as either transuranic or low-level waste requires very sensitive and accurate assay instrumentation to determine the specific radioactivity within an individual waste package. An assay instrument that employs a new technique (TRU-ART), which can identify the location of the radioactive material within a waste package, was designed, fabricated, and tested to potentially enhance the certification of problem defense waste drums. In addition, the assay instrumentation has potential application in radioactive waste reprocessing and neutron tomography. The assay instrumentation uses optimized electronic signal responses from an array of boral- and cadmium-shielded polyethylene-moderated 3 H detector packages. Normally, thermal neutrons that are detected by 3 H detectors have very poor spatial dependency that may be used to determine the location of the radioactive material. However, these shielded-detector packages of the TRU-ART system maintain the spatial dependency of the radioactive material in that the point of fast neutron thermalization is immediately adjacent to the 3 H detector. The TRU-ART was used to determine the location of radioactive material within three mock-up drums (empty, peat moss, and concrete) and four actual waste drums. The TRU-ART technique is very analogous to emission tomography. The mock-up drum and actual waste drum data, which were collected by the TRU-ART, were directly input into a algebraic reconstruction code to produce three-dimensional isoplots. Finally, a comprehensive fabrication cost estimate of the fielded drum assay system and the TRU-ART system was determined, and, subsequently, these estimates were used in a cost-benefit analysis to compare the economic advantage of the respective systems

Autologous osteochondral mosaicplasty or TruFit plugs for cartilage repair.

Science.gov (United States)

Hindle, Paul; Hendry, Jane L; Keating, John F; Biant, Leela C

2014-06-01

Autologous osteochondral mosaicplasty and TruFit Bone graft substitute plugs are methods used to repair symptomatic articular cartilage defects in the adult knee. There have been no comparative studies of the two techniques. This retrospective study assessed functional outcome of patients using the EQ-5D, Knee Injury and Osteoarthritis Outcome Score (KOOS) and Modified Cincinnati scores at follow-up of 1-5 years. There were 66 patients in the study (35 TruFit and 31 Mosaicplasty): 44 males and 22 females with a mean age of 37.3 years (SD 12.6). The mean BMI was 26.8. Thirty-six articular cartilage lesions were due to trauma, twenty-six due to osteochondritis dissecans and three due to non-specific degenerative change or unknown. There was no difference between the two groups age (n.s.), sex (n.s.), BMI (n.s.), defect location (n.s.) or aetiology (n.s.). The median follow-up was 22 months for the TruFit cohort and 30 months for the mosaicplasty group. There was no significant difference in the requirement for re-operation (n.s). Patients undergoing autologous mosaicplasty had a higher rate of returning to sport (p = 0.006), lower EQ-5D pain scores (p = 0.048) and higher KOOS activities of daily living (p = 0.029) scores. Sub-group analysis showed no difference related to the number of cases the surgeon performed. Patients requiring re-operation had lower outcome scores regardless of their initial procedure. This study demonstrated significantly better outcomes using two validated outcome scores (KOOS, EQ-5D), and an ability to return to sport in those undergoing autologous mosaicplasty compared to those receiving TruFit plugs. IV.

Gas generation and migration analysis for TRU waste disposal system

International Nuclear Information System (INIS)

Ando, Kenichi; Noda, Masaru; Yamamoto, Mikihiko; Mihara, Morihiro

2005-09-01

In TRU waste disposal system, significant quantities of gases may be generated due to metal corrosion, radiolysis effect and microorganism activities. It is therefore recommended that the potential impact of gas generation and migration on TRU waste repository should be evaluated. In this study, gas generation rates were calculated in the repository and gas migration analysis in the disposal system were carried out using two phase flow model with results of gas generation rates. First, the time dependencies of gas generation rate in each TRU waste repositories were evaluated based on amounts of metal, organic matter and radioactivity. Next, the accumulation pressure of gases and expelled pore water volume nuclides in the repository were calculated by TOUGH2 code. After that, the results showed that the increase of gas pressure was the range of 1.3 to 1.4 MPa. In the repository with and without buffer, the rate of expelled pore water was 0.006 - 0.009 m 3 /y and 0.018 - 0.24m 3 /y, respectively. In addition, the radioactive gas migration through the repository and geosphere are evaluated. And re-saturation analysis is also performed to evaluate the initial condition of the system. (author)

Development of safety assessment model based on TRU-2 report using GoldSim

International Nuclear Information System (INIS)

Ebina, Takanori; Inagaki, Manabu; Kato, Tomoko

2011-03-01

The safety assessment model at 'Second Progress Report on Research and Development for TRU Waste Disposal in Japan'(TRU-2 report) was designed using the numerical code TIGER, that allows the physical and chemical properties within the system to vary with time. In the future, at the examination to optimize nuclear fuel cycle for geological disposal, it is expected that the analysis that has many cases like sensitivity analysis and uncertainty analysis are in demand. The numerical code TIGER is a calculation code that analyze engineered barrier system and geological barrier system, and its numerical model is verified with nuclide migration code for engineered barrier system MESHNOTE, and nuclide migration code for geosphere MATRICS. At the analysis using TIGER, the migration (i.e. Engineered barrier system, Host rock and Fault) have to be analysed independently at each region, consequently the huge number of complicated parameter setting have been required. On the other hand, by using numerical code GoldSim, all regions are analyzed synchronously and parameters can be defined at same model. So it makes quality control of parameters easier. Furthermore, analysis time by GoldSim is shorter than TIGER and GoldSim can calculate many number of Monte Carlo simulations among multiple computers. In future, Safety Analyses of TRU waste package disposal will be carried out according as study of an optimization of nuclear fuel cycle. Therefor, safety assessment model for TRU waste disposal using GoldSim was designed, and calculation results were verified by comparing with the result of TRU-2 report. (author)

Feasibility analysis of constant TRU feeding in waste transmutation system using accelerator-driven subcritical system

Energy Technology Data Exchange (ETDEWEB)

Lee, Kun Jai; Cho, Nam Zin; Jo, Chang Keun; Park, Chang Je; Kim, Do Sam; Park, Jeong Hwan [Korea Advanced Institute of Science and Technology, Taejon (Korea)

1999-03-01

It is probable that the issue of nuclear spent fuel and high-level waste can have negative impact on the future expansion of nuclear power programs. Accelerator-driven nuclear waste transmutation with constant composition TRU feeding which satisfies non-proliferation condition will help establish the long-range nuclear waste disposal strategy. In this study, current status of accelerator-driven transmutation of waste technology, and feasibility analysis of constant composition TRU feeding system were investigated. We ascertained that solid system using constant composition TRU is feasible with the the capability of transmutation. (author). 13 refs., 53 figs., 20 tabs.

Fast reactor core design studies to cope with TRU fuel composition changes in the LWR-to-FBR transition period

International Nuclear Information System (INIS)

Kawashima, Katsuyuki; Maruyama, Shuhei; Ohki, Shigeo; Mizuno, Tomoyasu

2009-01-01

As part of the Fast Reactor Cycle Technology Development Project (FaCT Project), sodium-cooled fast reactor core design efforts have been made to cope with the TRU fuel composition changes expected during LWR-to-FBR transition period, in which a various kind of TRU fuel compositions are available depending on the characteristics of the LWR spent fuels and a way of recycling them. A 750 MWe mixed-oxide fuel core is firstly defined as a FaCT medium-size reference core and its neutronics characteristics are determined. The core is a high internal conversion type and has an average burnup of 150 GWD/T. The reference TRU fuel composition is assumed to come from the FBR equilibrium state. Compared to the LWR-to-FBR transition period, the TRU fuels in the FBR equilibrium period are multi-recycled through fast reactors and have a different composition. An available TRU fuel composition is determined by fast reactor spent fuel multi-recycling scenarios. Then the FaCT core corresponding to the TRU fuel with different compositions is set according to the TRU fuel composition changes in LWR-to-FBR transition period, and the key core neutronics characteristics are assessed. It is shown that among the core neutronics characteristics, the burnup reactivity and the safety parameters such as sodium void reactivity and Doppler coefficient are significantly influenced by the TRU fuel composition changes. As a result, a general characteristic in the FaCT core design to cope with TRU fuel composition changes is grasped and the design envelopes are identified in terms of the burnup reactivity and the safety parameters. (author)

Performance assessment for the disposal of low-level waste in the 200 east area burial grounds

Energy Technology Data Exchange (ETDEWEB)

Wood, M.I., Westinghouse Hanford

1996-08-15

A performance assessment analysis was completed for the 200 East Area Low-Level Burial Grounds (LLBG) to satisfy compliance requirements in DOE Order 5820.2A. In the analysis, scenarios of radionuclide release from the 200 East Area Low-Level waste facility was evaluated. The analysis focused on two primary scenarios leading to exposure. The first was inadvertent intrusion. In this scenario, it was assumed that institutional control of the site and knowledge of the disposal facility has been lost. Waste is subsequently exhumed and dose from exposure is received. The second scenario was groundwater contamination.In this scenario, radionuclides are leached from the waste by infiltrating precipitation and transported through the soil column to the underlying unconfined aquifer. The contaminated water is pumped from a well 100 m downstream and consumed,causing dose. Estimates of potential contamination of the surrounding environment were developed and the associated doses to the maximum exposed individual were calculated. The doses were compared with performance objective dose limits, found primarily in the DOE order 5850.2A. In the 200 East Area LLBG,it was shown that projected doses are estimated to be well below the limits because of the combination of environmental, waste inventory, and disposal facility characteristics of the 200 East Area LLBG. Waste acceptance criteria were also derived to ensure that disposal of future waste inventories in the 200 East Area LLBG will not cause an unacceptable increase in estimated dose.

Sensitivity of Transmutation Capability to Recycling Scenarios in KALIMER-600 TRU Burner

International Nuclear Information System (INIS)

Lee, Yong Kyo; Kim, Myung Hyun

2013-01-01

The purpose of this study is to test transmutation and design feasibility of KALIMER burner caused from many limitations in recycling options; such as low recovery factors and external feed. Design impact from many recycling options will be tested as a sensitivity to various recycling process parameters under many recycling scenarios. Through this study, possibilities when Pyro-processing is realized with SFR can be expected in the recycling scenarios. For the development of sodium-cooled fast reactor(SFR) technology, prototype KALIMER plant is now under R and D stage in Korea. For the future application of SFR for waste transmutation, KALIMER core was designed for TRU burner by KAERI. Feasibility of TRU burner cannot be evaluated exactly because overall functional parameters in pyro-processing recycling process has not been verified yet. There is great possibility to accept undesirable process functions in pyro-processing. Only TRU nuclides composition a little differs between PWR SF and CANDU SF so first scenario has no problem operating SFR. In second scenario, the radiotoxicity of waste at 99% of TRU RF have to be confirmed whether it is proper level to reposit as Low and Intermediate Level Wastes or not. And the reactor safety at high RF of RE must be inspected. Not only third scenario but also several scenarios for good measure are being calculated and will be evaluated

Partitioning of TRU elements from Chinese HLLW

International Nuclear Information System (INIS)

Song Chongli; Zhu Yongjun

1994-04-01

The partitioning of TRU elements from the Chinese HLLW is feasible. The required D.F. values for producing a waste suitable for land disposal are given. The TRPO process developed in China could be used for this purpose. The research and development of the TRPO process is summarized and the general flowsheet is given. The Chinese HLLW has very high salt concentration. It causes the formation of third phase when contacted with TRPO extractant. The third phase would disappear by diluting the Chinese HLLW to 2∼3 times before extraction. The preliminary experiment shows very attractive results. The separation of Sr and Cs from the Chinese HLLW is also possible. The process is being studied. The partitioning of TRU elements and long lived ratio-nuclides from the Chinese HLLW provides an alternative method for its disposal. The partitioning of the Chinese HLLW could greatly reduce the waste volume, that is needed to be vitrified and to be disposed in to the deep repository, and then would drastically save the overall waste disposal cost

TRU-waste decontamination and size reduction review, June 1983, US DOE/PNC technology exchange

International Nuclear Information System (INIS)

Becker, G.W. Jr.

1983-01-01

A review of transuranic (TRU) noncombustible waste decontamination and size reduction technology is presented. Electropolishing, vibratory cleaning, and spray decontamination processes developed at Battelle Pacific Northwest Laboratory (PNL) and Savannah River Laboratory (SRL) are highlighted. TRU waste size reduction processes at (PNL), Los Alamos National Laboratory (LANL), the Rocky Flats Plant (RFP), and SRL are also highlighted

Assessment of the Mechanisms for Sr-90 and TRU Removal from Complexant-Containing Tank Wastes at Hanford

International Nuclear Information System (INIS)

Hallen, Richard T.; Geeting, John GH; Lilga, Michael A.; Hart, Todd R.; Hoopes, Francis V.

2005-01-01

Small-scale tests (∼20 mL) were conducted with samples from Hanford underground storage tanks AN-102 and AN-107 to assess the mechanisms for removing Sr-90 and transuranics (TRU) from the liquid (supernatant) portion of the waste. The Sr-90 and TRU must be removed (decontaminated), in addition to Cs-137 and the entrained solids, before the supernatant can be disposed of as low-activity waste. Experiments were conducted with various reagents and modified Sr/TRU removal process conditions to more fully understand the reaction mechanisms. The optimized treatment conditions--no added hydroxide, addition of Sr (0.02M target concentration) followed by sodium permanganate (0.02M target concentration) with mixing at ambient temperature--were used as a reference for comparison. The waste was initially two orders of magnitude undersaturated with Sr; the addition of nonradioactive Sr(NO?) ? saturated the supernatant, resulting in isotopic dilution and precipitation of Sr-90 as SrCO?. The reaction chemistry of Mn species relevant to the mechanism of TRU removal by permanganate treatment was evaluated, along with the importance of various mechanisms for decontamination, such as precipitation, absorption, ligand exchange, and oxidation of organic complexants. For TRU removal, permanganate addition generally gave the highest DF. The addition of Mn of lower oxidation states (II, IV, and VI) also resulted in good TRU removal, as did complexant oxidation with periodate and addition of Zr(IV) for ligand exchange. These results suggest that permanganate treatment leads to TRU removal by multiple routes

Nuclear-waste-management technical support in the development of nuclear-waste-form criteria for the NRC. Task 2. Alternative TRU technologies

International Nuclear Information System (INIS)

Bida, G.; MacKenzie, D.R.

1982-02-01

Three main areas of transuranic (TRU) waste management are addressed: immobilization processes and waste forms for ultimate geologic disposal of TRU waste; decontamination as a method for TRU waste management; and potential problems associated with gas generation by certain TRU wastes. Waste forms are considered in terms of the regulations and criteria proposed in 10 CFR 60. Evaluation of the waste forms is based principally on ability to meet the release rate criterion of 10 -5 /year given in the Performance Objectives of Section 111, but also on the general requirements of Section 133. The two classes of metallic waste which are candidates for decontamination treatment are Zircaloy cladding hulls from light water reactor fuel elements, and failed facilities and equipment. Decontamination methods are addressed with regard to their ability to remove contamination to a level below the 10 nCi/g TRU limit. Other important factors are the volume reduction achieved, and compatibility of the secondary waste streams with acceptable waste forms. Gas generation by combustible TRU wastes and cast concretes containing TRU isotopes is discussed, and its potential for damage to a geologic repository is considered. Exclusion of combustible TRU waste from repositories is recommended. Conclusions are drawn about the suitability of various waste forms and recommendations are made regarding further work needed in the development of specific TRU waste forms

Effects of conversion ratio change on the core performances in medium to large TRU burning reactors

International Nuclear Information System (INIS)

Song, Hoon; Kim, Sang-Ji; Yoo, Jae-Woon; Kim, Yeong-Il

2009-01-01

Conceptual fast reactor core designs with sodium coolant are developed at 1,500, 3,000 and 4,500 MWt which are configured to transmute recycled transuranics (TRU) elements with external feeds consisting of LWR spent fuel. Even at each pre-determined power level, the performance parameters, reactivity coefficients and their implications on the safety analysis can be different when the target TRU conversion ratio changes. In order to address this aspect of design, a study on TRU conversion ratio change was performed. The results indicate that it is feasible to design a TRU burner core to accommodate a wide range of conversion ratios by employing different fuel cladding thicknesses. The TRU consumption rate is found to be proportional to the core power without any significant deterioration in the core performance at higher power levels. A low conversion ratio core has an increased TRU consumption rate and much faster burnup reactivity loss, which calls for appropriate means for reactivity compensation. As for the reactivity coefficients related with the conversion ratio change, the core with a low conversion ratio has a less negative Doppler coefficient, a more negative axial expansion coefficient, a more negative control rod worth per rod, a more negative radial expansion coefficient, a less positive sodium density coefficient and a less positive sodium void worth. A slight decrease in the delayed neutron fraction is also noted, reflecting the fertile U-238 fraction reduction. (author)

Pyrolysis/Steam Reforming Technology for Treatment of TRU Orphan Wastes

International Nuclear Information System (INIS)

Mason, J. B.; McKibbin, J.; Schmoker, D.; Bacala, P.

2003-01-01

Certain transuranic (TRU) waste streams within the Department of Energy (DOE) complex cannot be disposed of at the Waste Isolation Pilot Plant (WIPP) because they do not meet the shipping requirements of the TRUPACT-II or the disposal requirements of the Waste Analysis Plan (WAP) in the WIPP RCRA Part B Permit. These waste streams, referred to as orphan wastes, cannot be shipped or disposed of because they contain one or more prohibited items, such as liquids, volatile organic compounds (VOCs), hydrogen gas, corrosive acids or bases, reactive metals, or high concentrations of polychlorinated biphenyl (PCB), etc. The patented, non-incineration, pyrolysis and steam reforming processes marketed by THOR Treatment Technologies LLC removes all of these prohibited items from drums of TRU waste and produces a dry, inert, inorganic waste material that meets the existing TRUPACT-II requirements for shipping, as well as the existing WAP requirements for disposal of TRU waste at WIPP. THOR Treatment Technologies is a joint venture formed in June 2002 by Studsvik, Inc. (Studsvik) and Westinghouse Government Environmental Services Company LLC (WGES) to further develop and deploy Studsvik's patented THORSM technology within the DOE and Department of Defense (DoD) markets. The THORSM treatment process is a commercially proven system that has treated over 100,000 cu. ft. of nuclear waste from commercial power plants since 1999. Some of this waste has had contact dose rates of up to 400 R/hr. A distinguishing characteristic of the THORSM process for TRU waste treatment is the ability to treat drums of waste without removing the waste contents from the drum. This feature greatly minimizes criticality and contamination issues for processing of plutonium-containing wastes. The novel features described herein are protected by issued and pending patents

MANAGEING THE RETRIEVAL RISK OF BURIED TRANSURANIC (TRU) WASTE WITH UNIQUE CHARACTERISTICS

International Nuclear Information System (INIS)

WOJTASEK, R.D.; GREENWELL, R.D.

2005-01-01

United States-Department of Energy (DOE) sites that store transuranic (TRU) waste are almost certain to encounter waste packages with characteristics that are so unique as to warrant special precautions for retrieval. At the Hanford Site, a subgroup of stored TRU waste (12 drums) had special considerations due to the radioactive source content of plutonium oxide (PuO 2 ), and the potential for high heat generation, pressurization, criticality, and high radiation. These characteristics bear on the approach to safely retrieve, overpack, vent, store, and transport the waste package. Because of the potential risk to personnel, contingency planning for unexpected conditions played an effective roll in work planning and in preparing workers for the field inspection activity. As a result, the integrity inspections successfully confirmed waste package configuration and waste confinement without experiencing any perturbations due to unanticipated packaging conditions. This paper discusses the engineering and field approach to managing the risk of retrieving TRU waste with unique characteristics

Centralized processing of contact-handled TRU waste feasibility analysis

International Nuclear Information System (INIS)

1986-12-01

This report presents work for the feasibility study of central processing of contact-handled TRU waste. Discussion of scenarios, transportation options, summary of cost estimates, and institutional issues are a few of the subjects discussed

Savannah River Site Operating Experience with Transuranic (TRU) Waste Retrieval

International Nuclear Information System (INIS)

Stone, K.A.; Milner, T.N.

2006-01-01

Drums of TRU Waste have been stored at the Savannah River Site (SRS) on concrete pads from the 1970's through the 1980's. These drums were subsequently covered with tarpaulins and then mounded over with dirt. Between 1996 and 2000 SRS ran a successful retrieval campaign and removed some 8,800 drums, which were then available for venting and characterization for WIPP disposal. Additionally, a number of TRU Waste drums, which were higher in activity, were stored in concrete culverts, as required by the Safety Analysis for the Facility. Retrieval of drums from these culverts has been ongoing since 2002. This paper will describe the operating experience and lessons learned from the SRS retrieval activities. (authors)

Mound No. 24 of the Alebastrovo I Burial Ground and the Problem of Succession Among the Early Nomadic Cultures of the Southern Urals in the 6th – 4th and 3rd – 1st Centuries BC

Directory of Open Access Journals (Sweden)

Denis V. Maryksin

2017-03-01

Full Text Available The article focuses on one of the burial mounds – Alebastrovo I, which is situated in the middle reaches of the Ural river. The analysis of the burial rite and grave goods reveals the combination of features peculiar of the culture of early nomads from the 6th to the 4th centuries BC and later features typical for the 3rd – 1st centuries BC. The collective nature of the burial in a large square pit (burial no. 2 relates to early features. Such burials are typical for the 5th and 4th centuries BC. But a dagger with a direct crosshair and a crescent-shaped pommel found in the burial belongs to the 3rd – 1st centuries BC. Findings of a mirror, a spoon and a whorl also deserve special attention. On formal grounds a mirror belongs to the type “Skripkin 1.6” – with a flat disk without roll and stick in the form of a triangular stem. They appeared in Sauromatian time, but were not widespread. Most of these mirrors refer to the turn of the eras – the first centuries AD. However, in our view the mirror from Alebastrovo I has the greatest similarity with the mirror disks of the so-called “musical” mirrors, which date back to the 2nd half of the 4th century BC. The bone spoon belongs to the type I, peculiar of the Sauromatian-time things of the 6th – 4th centuries BC. However, the pattern is similar to that on the handle of the bone products of later time – the 3rd – 2nd centuries BC. Clay whorl has a pattern in the form of 4 sectors, decorated with grooves and pits. Analogies are available on this ornament spindles from the 3rd – 2nd centuries BC of the Kara-Abyz culture in the Southern Urals. According to the set of attributes, this burial mound dated to the second half of the 3rd - 2nd centuries BC. The finds from this burial mound confirm the conclusion of the first explorer B. F. Zhelezchikov about continuity of the development of the early nomadic culture of this region in the 6th – 3rd centuries BC.

Research on safety evaluation for TRU waste disposal

International Nuclear Information System (INIS)

Senoo, M.; Shirahashi, K.; Sakamoto, Y.; Moriyama, N.; Konishi, M.

1989-01-01

Studies on adsorption behavior of transuranic (TRU) elements have been performed from the view point of validating the data for safety assessment and investigating adsorption behavior of TRU elements. Distribution coefficient (Kd value) of plutonium between groundwater and soils sampled at the planning site of low level waste disposal facility were measured for safety assessment. Kd values measured were the order of 10 3 ml/g. For investigating adsorption behavior, pH dependency of Kd value of neptunium and Am for soils were studied. It was concluded that pH dependency of Kd value of neptunium was mainly owing to amount of surface charge of soils, on the other hand that of Am was due to chemical form of Am. Influence of carbonation of cement for adsorption behavior of neptunium and plutonium was also investigated and it was concluded that Kd value of carbonated cement was lower than that of fresh cement

TRU waste certification and TRUPACT-II payload verification

International Nuclear Information System (INIS)

Hunter, E.K.; Johnson, J.E.

1990-01-01

The Waste Isolation Pilot Plant (WIPP) established a policy (subsequently confirmed and required by DOE Order 5820.2A, Radioactive Waste Management, September 1988) that requires each waste shipper to verify that all waste shipments meet the requirements of the Waste Acceptance Criteria (WAC) prior to being shipped. This verification provides assurance that transuranic (TRU) wastes meet the criteria while still retained in a facility where discrepancies can be immediately corrected. In this manner, problems that would arise if WAC violations were discovered at the receiver, where corrective facilities are not available, are avoided. Each Department of Energy (DOE) TRU waste facility planning to ship waste to the Waste Isolation Pilot Plant (WIPP) is required to develop and implement a specific program including Quality Assurance (QA) provisions to verify that waste is in full compliance with WIPP's WAC. This program is audited by a composite DOE and contractor audit team prior to granting the facility permission to certify waste. During interaction with the Nuclear Regulatory Commission (NRC) on payload verification for shipping in TRUPACT-II, a similar system was established by DOE. The TRUPACT-II Safety Analysis Report (SAR) contains the technical requirements and physical and chemical limits that payloads must meet (like the WAC). All shippers must plan and implement a payload control program including independent QA provisions. A similar composite audit team will conduct preshipment audits, frequent subsequent audits, and operations inspections to verify that all TRU waste shipments in TRUPACT-II meet the requirements of the Certificate of Compliance (C of C) issued by the NRC which invokes the SAR requirements. 1 fig

DEVELOPMENT OF THE TRU WASTE TRANSPORTATION FLEET--A SUCCESS STORY

International Nuclear Information System (INIS)

Devarakonda, Murthy; Morrison, Cindy; Brown, Mike

2003-01-01

Since March 1999, the Waste Isolation Pilot Plant (WIPP), located in southeastern New Mexico, has been operated by the U.S. Department of Energy (DOE), Carlsbad Field Office (CBFO), as a repository for the permanent disposal of defense-related transuranic (TRU) waste. More than 1,450 shipments of TRU waste for WIPP disposal have been completed, and the WIPP is currently receiving 12 to 16 shipments per week from five DOE sites around the nation. One of the largest fleets of Type B packagings supports the transportation of TRU waste to WIPP. This paper discusses the development of this fleet since the original Certificate of Compliance (C of C) for the Transuranic Package Transporter-II (TRUPACT-II) was issued by the U.S. Nuclear Regulatory Commission (NRC) in 1989. Evolving site programs, closure schedules of major sites, and the TRU waste inventory at the various DOE sites have directed the sizing and packaging mix of this fleet. This paper discusses the key issues that guided this fleet development, including the following: While the average weight of a 55-gallon drum packaging debris could be less than 300 pounds (lbs.), drums containing sludge waste or compacted waste could approach the maximum allowable weight of 1,000 lbs. A TRUPACT-II shipment may consist of three TRUPACT-II packages, each of which is limited to a total weight of 19,250 lbs. Payload assembly weights dictated by ''as-built'' TRUPACT-II weights limit each drum to an average weight of 312 lbs when three TRUPACT-IIs are shipped. To optimize the shipment of heavier drums, the HalfPACT packaging was designed as a shorter and lighter version of the TRUPACT-II to accommodate a heavier load. Additional packaging concepts are currently under development, including the ''TRUPACT-III'' packaging being designed to address ''oversized'' boxes that are currently not shippable in the TRUPACT-II or HalfPACT due to size constraints. Shipment optimization is applicable not only to the addition of new

Biomass burial and storage to reduce atmospheric CO2

Science.gov (United States)

Zeng, N.

2012-04-01

To mitigate global climate change, a portfolio of strategies will be needed to keep the atmospheric CO2 concentration below a dangerous level. Here a carbon sequestration strategy is proposed in which certain dead or live trees are harvested via collection or selective cutting, then buried in trenches or stowed away in above-ground shelters. The largely anaerobic condition under a sufficiently thick layer of soil will prevent the decomposition of the buried wood. Because a large flux of CO2 is constantly being assimilated into the world's forests via photosynthesis, cutting off its return pathway to the atmosphere forms an effective carbon sink. It is estimated that a theoretical carbon sequestration potential for wood burial is 10 ± 5 GtC/y, but probably 1-3 GtC/y can be realized in practice. Burying wood has other benefits including minimizing CO2 source from deforestation, extending the lifetime of reforestation carbon sink, and reducing fire danger. There are possible environmental impacts such as nutrient lock-up which nevertheless appears manageable, but other environmental concerns and factors will likely set a limit so that only part of the full potential can be realized. Based on data from forest industry, the cost for wood burial is estimated to be 14/tCO2 (50/tC), lower than the typical cost for power plant CO2 capture with geological storage. The low cost for carbon sequestration with wood burial is possible because the technique uses the natural process of photosynthesis to remove carbon from the atmosphere. The technique is low tech, distributed, safe, and can be stopped at any time, thus an attractive option for large-scale implementation in a world-wide carbon market.

In situ vitrification on buried waste

International Nuclear Information System (INIS)

Bates, S.O.

1992-01-01

In situ vitrification (ISV) is being evaluated as a remedial treatment technology for buried mixed and transuranic (TRU) wastes at the Subsurface Disposal Area (SDA) at Idaho National Engineering Laboratory (INEL) and can be related to buried wastes at other Department of Energy (DOE) sites. There are numerous locations around the DOE Complex where wastes were buried in the ground or stored for future burial. The Buried Waste Program (BWP) is conducting a comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) remedial investigation/feasibility study (RI/FS) for the Department of Energy - Field Office Idaho (DOE-ID). As part of the RI/FS, an ISV scoping study on the treatability of the SDA mixed low-level and mixed TRU waste is being performed for applicability to remediation of the waste at the Radioactive Waste Management Complex (RWMC). The ISV project being conducted at the INEL by EG ampersand G Idaho, Inc. consists of a treatability investigation to collect data to satisfy nine CERCLA criteria with regards to the SDA. This treatability investigation involves a series of experiments and related efforts to study the feasibility of ISV for remediation of mixed and TRU waste disposed of at the SDA

Waste Receiving and Processing Facility Module 1: Volume 1, Preliminary Design report

International Nuclear Information System (INIS)

1992-03-01

The Preliminary Design Report (Title 1) for the Waste Receiving and Processing (WRAP) Module 1 provides a comprehensive narrative description of the proposed facility and process systems, the basis for each of the systems design, and the engineering assessments that were performed to support the technical basis of the Title 1 design. The primary mission of the WRAP 1 Facility is to characterize and certify contact-handled (CH) waste in 55-gallon drums for disposal. Its secondary function is to certify CH waste in Standard Waste Boxes (SWBs) for disposal. The preferred plan consist of retrieving the waste and repackaging as necessary in the Waste Receiving and Processing (WRAP) facility to certify TRU waste for shipment to the Waste Isolation Pilot Plant (WIPP) in New Mexico. WIPP is a research and development facility designed to demonstrate the safe and environmentally acceptable disposal of TRU waste from National Defense programs. Retrieved waste found to be Low-Level Waste (LLW) after examination in the WRAP facility will be disposed of on the Hanford site in the low-level waste burial ground. The Hanford Site TRU waste will be shipped to the WIPP for disposal between 1999 and 2013

Neutron spectrum effects on TRU recycling in Pb-Bi cooled fast reactor core

International Nuclear Information System (INIS)

Kim, Yong Nam; Kim, Jong Kyung; Park, Won Seok

2003-01-01

This study is intended to evaluate the dependency of TRU recycling characteristics on the neutron spectrum shift in a Pb-Bi cooled core. Considering two Pb-Bi cooled cores with the soft and the hard spectrum, respectively, various characteristics of the recycled core are carefully examined and compared with each other. Assuming very simplified fuel cycle management with the homogeneous and single region fuel loading, the burnup calculations are performed until the recycled core reached to the (quasi-) equilibrium state. The mechanism of TRU recycling toward the equilibrium is analyzed in terms of burnup reactivity and the isotopic compositions of TRU fuel. In the comparative analyses, the difference in the recycling behavior between the two cores is clarified. In addition, the basic safety characteristics of the recycled core are also discussed in terms of the Doppler coefficient, the coolant loss reactivity coefficient, and the effective delayed neutron fraction

Biópsia hepática com agulha tru-cut guiada por videolaparoscopia em caprinos Videolaparoscopic guided hepatic biopsy with tru-cut needle in goats

Directory of Open Access Journals (Sweden)

A.L.L. Duarte

2009-02-01

Full Text Available Descreve-se a técnica de biópsia hepática com agulha tru-cut guiada por videolaparoscopia em 12 caprinos machos, castrados, hígidos, sem raça definida, distribuídos em dois grupos (G: G1, com cinco animais de 12 meses e G2, com sete de seis meses de idade. O procedimento foi realizado sob anestesia geral intravenosa com o animal em decúbito lateral esquerdo. O pneumoperitônio e a laparoscopia foram procedidos no flanco direito, aproximadamente a 10cm ventral aos processos transversos das vértebras lombares. A agulha tru-cut foi introduzida no 11º espaço intercostal direito, a aproximadamente 12cm ventral à coluna vertebral, para punção e remoção de fragmento do lobo hepático direito. O tempo operatório médio foi de 23 minutos e cinco segundos. A hemorragia causada pela perfuração hepática cessou em dois minutos em 75% dos animais e em três minutos, nos 25% restantes. Nas avaliações clínicas feitas no pré-jejum e às 24, 48 e 72 horas após a biópsia, não foram observadas alterações (P>0,05 da temperatura retal, das frequências cardíaca e respiratória e dos movimentos rumenais nos dois grupos. A biópsia hepática com agulha tru-cut guiada por videolaparoscopia foi considerada eficaz para uso em caprinos, permitindo a obtenção de fragmentos hepáticos suficientes para exame histológico.The videolaparoscopic guided hepatic biopsy with tru-cut needle is described in 12 healthy, no defined breed, castrated male goats. Animals were distributed in two groups: G1 (n=5 12-month-old animals; and G2 (n=7 six-month-old animals. The procedure was performed with the animal in left lateral recumbency and under total intravenous anesthesia. Pneumoperitoneum and laparoscopy were performed in the right flank, approximately 10cm ventral to the transverse processes of the lumbar vertebrae. The tru-cut needle was inserted into the right eleventh intercostal space, around 12cm ventral to the spinal column, for punching and

The TRUEX [TRansUranium EXtraction] process and the management of liquid TRU [transuranic] waste

International Nuclear Information System (INIS)

Schulz, W.W.; Horwitz, E.P.

1987-01-01

The TRUEX process is a new generic liquid-liquid extraction process for removal of all actinides from acidic nitrate or chloride nuclear waste solutions. Because of its high efficiency and great flexibility, the TRUEX process appears destined to be widely used in the US and possibly in other countries for cost-effective management and disposal of transuranic (TRU) wastes. In the US, TRU wastes are those that contain ≥3.7 x 10 6 Bq/kg) of TRU elements with half-lives greater than 20 y. This paper gives a brief review of the relevant chemistry and summarizes the current status of development and deployment of the TRUEX (TRansUranium EXtraction) process flowsheets to treat specific acidic waste solutions at several US Department of Energy sites. 19 refs., 4 figs., 4 tabs

Burial ground as a containment system: 25 years of subsurface monitoring at the Savannah River Plant Facility

International Nuclear Information System (INIS)

Fenimore, J.W.

1982-01-01

As the Savannah River Plant (SRP) solid wastes containing small quantities of radionuclides are buried in shallow (20' deep) trenches. The hydrogeology of the burial site is described together with a variety of subsurface monitoring techniques employed to ensure the continued safe operation of this disposal facility. conclusions from over two decades of data collection are presented

Roman Bronze Vessels From the Late Sarmatian Burial of the Lebedevka Burial-Ground in Western Kazakhstan

Directory of Open Access Journals (Sweden)

Treister Mikhail Yuryevich

2015-12-01

Full Text Available This paper is devoted to studying cultural monuments – bronze vessels, a jug and a basin from the barrow no. 1/1967 of the Lebedevka Late Sarmatian burial mound (Western Kazakhstan, dating back to the middle of the 3rd century AD at the latest. These items do not find exact parallels among the bronze vessels of provincial Rome. Although the shape of the jug handle with a curved leaf turned upright between two horizontally arranged swan heads has parallels on the so-called “composite jug with handles” (“gegliederten Henkelkrügen”, the cylindrical form of the jug’s neck peculiar of the glass jugs of allegedly Syrian manufacture of the second half of the 3rd-4th centuries AD is very unusual. Even more unusual is a basin with horizontally bent rim and elaborate handles with pearls on a high narrow stand-ring. The XRF analyses of the Lebedevka jug’s metal revealed that its body and handle were made of a copper-based alloy with very high admixtures of zinc (24-27 % and inconsiderable additions of lead (up to 3 %. A similar alloy was used for manufacturing a vessel in the form of a crouching young negro from Niederbieber. Most objects of provincial Roman import reached Western Kazakhstan via the Bosporan kingdom along the Northern branch of the Silk Road. The above discussed bronze vessels from Lebedevka let suggest, that the nomads could receive some import articles that were brought along the caravan routes leading from Egypt and Syria to the East.

Intermediate depth burial of classified transuranic wastes in arid alluvium

International Nuclear Information System (INIS)

Cochran, J.R.; Crowe, B.M.; Di Sanza, F.

1999-01-01

Intermediate depth disposal operations were conducted by the US Department of Energy (DOE) at the DOE's Nevada Test Site (NTS) from 1984 through 1989. These operations emplaced high-specific activity low-level wastes (LLW) and limited quantities of classified transuranic (TRU) wastes in 37 m (120-ft) deep, Greater Confinement Disposal (GCD) boreholes. The GCD boreholes are 3 m (10 ft) in diameter and founded in a thick sequence of arid alluvium. The bottom 15 m (50 ft) of each borehole was used for waste emplacement and the upper 21 m (70 ft) was backfilled with native alluvium. The bottom of each GCD borehole is almost 200 m (650 ft) above the water table. The GCD boreholes are located in one of the most arid portions of the US, with an average precipitation of 13 cm (5 inches) per year. The limited precipitation, coupled with generally warm temperatures and low humidities results in a hydrologic system dominated by evapotranspiration. The US Environmental Protection Agency's (EPA's) 40 CFR 191 defines the requirements for protection of human health from disposed TRU wastes. This EPA standard sets a number of requirements, including probabilistic limits on the cumulative releases of radionuclides to the accessible environment for 10,000 years. The DOE Nevada Operations Office (DOE/NV) has contracted with Sandia National Laboratories (Sandia) to conduct a performance assessment (PA) to determine if the TRU wastes emplaced in the GCD boreholes complies with the EPA's 40 CFR 191 requirements. This paper describes DOE's actions undertaken to evaluate whether the TRU wastes in the GCD boreholes will, or will not, endanger human health. Based on preliminary modeling, the TRU wastes in the GCD boreholes meet the EPA's requirements, and are, therefore, protective of human health

Sickly slaves, soldiers and sailors. Contextualising the Cape's 18th–19th century Green Point burials through isotope investigation

NARCIS (Netherlands)

Mbeki, Linda; Kootker, Lisette M.; Kars, Henk; Davies, Gareth R.

2017-01-01

Strontium isotope data of multiple dental enamel samples, and carbon and nitrogen isotope data of dentine and bone collagen samples from 27 individuals excavated from the mid-18th to mid-19th century Victoria & Albert Marina Residence paupers burial ground in the vicinity of Green Point, Cape Town,

Korea’s Experience on the Development of TRU Deep-Burn Concept Using HTGR

International Nuclear Information System (INIS)

Jo, Chang Keun

2013-01-01

From the results of the LPCC analysis, • Key design characteristics of the DB-HTR core are more fuel rings (five fuel-rings), less central reflectors (three rings) and the decay power curves due to the TRU fuel compositions that are different from the UO 2 fueled HTR core. • For a 0.2% UO 2 mixed or a 30% UO 2 mixed TRU, the reduced decay power obtained by removing the initial Am isotopes and by reducing the PF decreases the peak fuel temperature. However, the peak fuel temperatures are still higher than 1600 °C due to the lack of heat absorber volume in the central reflector. (600MW th DB-HTR case); • The 450MW th DB-HTR core is suggested as the optimization core design, which has the allowable maximum power reactor of a 450 MW th to the accident fuel design limit for 0.2%UO2 mixed TRU (PF=6.9%) or 30%UO 2 mixed TRU (PF=8.0%) using the mixed burnable poison of B 4 C and Er 2 O 3 . • Based on JAEA method, the effect of graphite annealing on the peak fuel temperature is small. The GA method indicates a much larger impact. In addition, it shows that the impact of the FB end-flux-peaking on the peak fuel temperature is not significant

Final hazard classification and auditable safety analysis for the 300-FF-1 Operable Unit liquid waste sites, landfills, and Burial Ground 618-4

International Nuclear Information System (INIS)

Adam, W.J.; Larson, A.R.

1996-12-01

This document provides the hazard categorizations and classifications for the activities associated with the 300-FF-1 Operable Unit (OU) remediation. Categories and classifications presented are applicable only to the 300-FF-1 OU waste sites specifically listed in the inventory. The purpose of this remedial action is to remove contaminated soil, debris, and solid waste from liquid waste sites, landfills, and Burial Ground 618-4 within the 300-FF-1 OU. Resulting waste from this project will be sent to the Environmental Restoration Disposal Facility (ERDF) in the 200 West Area. The 300-FF-1 OU is part of the 300 Area of the Hanford Site and is next to the Columbia River. The objective of this remedial action is to reduce contamination at these waste sites to levels that are acceptable for industrial purposes. Specific remedial objectives (cleanup goals) for each contaminant of concern (COC) are provided in a table, along with the maximum soil concentration detected

The WIPP RCRA Part B permit application for TRU mixed waste disposal

International Nuclear Information System (INIS)

Johnson, J.E.

1995-01-01

In August 1993, the New Mexico Environment Department (NMED) issued a draft permit for the Waste Isolation Pilot Plant (WIPP) to begin experiments with transuranic (TRU) mixed waste. Subsequently, the Department of Energy (DOE) decided to cancel the on-site test program, opting instead for laboratory testing. The Secretary of the NMED withdrew the draft permit in 1994, ordering the State's Hazardous and Radioactive Waste Bureau to work with the DOE on submittal of a revised permit application. Revision 5 of the WIPP's Resource Conservation and Recovery Act (RCRA) Part B Permit Application was submitted to the NMED in May 1995, focusing on disposal of 175,600 m 3 of TRU mixed waste over a 25 year span plus ten years for closure. A key portion of the application, the Waste Analysis Plan, shifted from requirements to characterize a relatively small volume of TRU mixed waste for on-site experiments, to describing a complete program that would apply to all DOE TRU waste generating facilities and meet the appropriate RCRA regulations. Waste characterization will be conducted on a waste stream basis, fitting into three broad categories: (1) homogeneous solids, (2) soil/gravel, and (3) debris wastes. Techniques used include radiography, visually examining waste from opened containers, radioassay, headspace gas sampling, physical sampling and analysis of homogeneous wastes, and review of documented acceptable knowledge. Acceptable knowledge of the original organics and metals used, and the operations that generated these waste streams is sufficient in most cases to determine if the waste has toxicity characteristics, hazardous constituents, polychlorinated biphenyls (PBCs), or RCRA regulated metals

Fundamental Studies of the Removal of Contaminants from Ground and Waste Waters via Reduction by Zero-Valent Metals

International Nuclear Information System (INIS)

Yarmoff, Jory A.; Amrhein, Christopher

1999-01-01

Contaminated groundwater and surface waters are a problem throughout the United States and the world. In many instances, the types of contamination can be directly attributed to man's actions. For instance, the burial of chemical wastes, casual disposal of solvents in unlined pits, and the development of irrigated agriculture have all contributed to groundwater and surface water contamination. The kinds of contaminants include chlorinated solvents and toxic trace elements (including radioisotopes) that are soluble and mobile in soils and aquifers. Oxyanions of uranium, selenium, chromium, arsenic, technetium, and chlorine (as perchlorate) are frequently found as contaminants on many DOE sites. Uranium is a particularly widespread contaminant at most DOE sites including Oak Ridge, Rocky Flats, Hanford, Idaho (INEEL), and Fernald. The uranium contamination is associated with mining and milling of uranium ore (UMTRA sites), isotope separation and enrichment, and mixed waste and TRU waste burial. In addition, the careless disposal of halogenated solvents, such as carbon tetrachloride and trichloroethylene, has further contaminated many groundwaters at these sites. A potential remediation method for many of these oxyanions and chlorinated-solvents is to react the contaminated water with zero-valent iron. In this reaction, the iron serves as both an electron source and as a catalyst. Elemental iron is already being used on an experimental basis at many DOE sites. Both in situ reactive barriers and above-ground reactors are being developed for this purpose. However, the design and operation of these treatment systems requires a detailed process-level understanding of the interactions between the contaminants and the iron surfaces. We are performing fundamental investigations of the interactions of the relevant chlorinated solvents and trace element-containing compounds with single- and poly-crystalline Fe surfaces. The aim of this work is to develop th e fundamental

Textiles from Scythian burial complexes

Directory of Open Access Journals (Sweden)

Elena Fialko

2013-12-01

Full Text Available In Northern Black Sea steppes were excavated more than three thousand Scythian burial mounds. In the studied burials were discovered large quantities of artifacts, but leather and textile items are preserved only in a few cases. Some ideas about Scythian costume are found in the works of Greek authors. In this regard, extremely important is the funerary complex dated with the 4th century BC, discovered in barrow Vishnevaja Moghila (Zaporizhia region, Ukraine. In the crypt, which remained undisturbed over time, was found a burial of a Scythian girl. The unique condition of preservation of the textiles and leather findings allowed reconstructing the entire costume of the Scythian. It consisted of six layers of clothing. Various pieces of clothing were made from different materials: white linen cloth, orange satin fabric, reddish-brown fur, black cloth, fur, red skin. This discovery is one of a kind in the Northern Black Sea region, which is currently a reference example of female costume of early nomads of the region.

Development of TRU waste mobile analysis methods for RCRA-regulated metals

International Nuclear Information System (INIS)

Mahan, C.A.; Villarreal, R.; Drake, L.; Figg, D.; Wayne, D.; Goldstein, S.

1998-01-01

This is the final report of a one-year, Laboratory Directed Research and Development (LDRD) project at Los Alamos National Laboratory (LANL). Glow-discharge mass spectrometry (GD-MS), laser-induced breakdown spectroscopy (LIBS), dc-arc atomic-emission spectroscopy (DC-ARC-AES), laser-ablation inductively-coupled-plasma mass spectrometry (LA-ICP-MS), and energy-dispersive x-ray fluorescence (EDXRF) were identified as potential solid-sample analytical techniques for mobile characterization of TRU waste. Each technology developers was provided with surrogate TRU waste samples in order to develop an analytical method. Following successful development of the analytical method, five performance evaluation samples were distributed to each of the researchers in a blind round-robin format. Results of the round robin were compared to known values and Transuranic Waste Characterization Program (TWCP) data quality objectives. Only two techniques, DC-ARC-AES and EDXRF, were able to complete the entire project. Methods development for GD-MS and LA-ICP-MS was halted due to the stand-down at the CMR facility. Results of the round-robin analysis are given for the EDXRF and DCARC-AES techniques. While DC-ARC-AES met several of the data quality objectives, the performance of the EDXRF technique by far surpassed the DC-ARC-AES technique. EDXRF is a simple, rugged, field portable instrument that appears to hold great promise for mobile characterization of TRU waste. The performance of this technique needs to be tested on real TRU samples in order to assess interferences from actinide constituents. In addition, mercury and beryllium analysis will require another analytical technique because the EDXRF method failed to meet the TWCP data quality objectives. Mercury analysis is easily accomplished on solid samples by cold vapor atomic fluorescence (CVAFS). Beryllium can be analyzed by any of a variety of emission techniques

Gas generation from radiolytic attack of TRU-contaminated hydrogenous waste

International Nuclear Information System (INIS)

Zerwekh, A.

1979-06-01

In 1970, the Waste Management and Transportation Division of the Atomic Energy Commission ordered a segregation of transuranic (TRU)-contaminated solid wastes. Those below a contamination level of 10 nCi/g could still be buried; those above had to be stored retrievably for 20 y. The possibility that alpha-radiolysis of hydrogenous materials might produce toxic, corrosive, and flammable gases in retrievably stored waste prompted an investigation of gas identities and generation rates in the laboratory and field. Typical waste mixtures were synthesized and contaminated for laboratory experiments, and drums of actual TRU-contaminated waste were instrumented for field testing. Several levels of contamination were studied, as well as pressure, temperature, and moisture effects. G (gas) values were determined for various waste matrices, and degradation products were examined

The effect of vibration on alpha radiolysis of transuranic (TRU) waste

International Nuclear Information System (INIS)

Zerwekh, A.; Kosiewicz, S.; Warren, J.

1993-01-01

This paper reports on previously unpublished scoping work related to the potential for vibration to redistribute radionuclides on transuranic (TRU) waste. If this were to happen, the amount of gases generated, including hydrogen, could be increased above the undisturbed levels. This could be an important consideration for transport of TRU wastes either at DOE sites or from them to a future repository, e.g., the Waste Isolation Pilot Plant (WIPP). These preliminary data on drums of real waste seem to suggest that radionuclide redistribution does not occur. However improvements in the experimental methodology are suggested to enhance safety of future experiments on real wastes as well as to provide more rigorous data

Determination of H2 Diffusion Rates through Various Closures on TRU Waste Bag-Out Bags

International Nuclear Information System (INIS)

Noll, Phillip D. Jr.; Callis, E. Larry; Norman, Kirsten M.

1999-01-01

The amount of H 2 diffusion through twist and tape (horse-tail), wire tie, plastic tie, and heat sealed closures on transuranic (TRU) waste bag-out bags has been determined. H 2 diffusion through wire and plastic tie closures on TRU waste bag-out bags has not been previously characterized and, as such, TRU waste drums containing bags with these closures cannot be certified and/or shipped to the Waste Isolation Pilot Plant (WIPP). Since wire ties have been used at Los Alamos National Laboratory (LANL) from 1980 to 1991 and the plastic ties from 1991 to the present, there are currently thousands of waste drums that cannot be shipped to the WIPP site. Repackaging the waste would be prohibitively expensive. Diffusion experiments performed on the above mentioned closures show that the diffusion rates of plastic tie and horse-tail closures are greater than the accepted value presented in the TRU-PACT 11 Safety Analysis Report (SAR). Diffusion rates for wire tie closures are not statistically different from the SAR value. Thus, drums containing bags with these closures can now potentially be certified which would allow for their consequent shipment to WIPP

Evaluation of dynamic compaction of low level waste burial trenches containing B-25 boxes

International Nuclear Information System (INIS)

McMullin, S.R.

1994-01-01

The Savannah River Site, owned by the US Department of Energy, is preparing to close an additional 13.8 ha of burial grounds under the Resource Conservation Recovery Act. In preparation for this closure, the dynamic compaction facility was designed and constructed to address unresolved design issues. Among these issues is the evaluation of the ability for dynamic compaction to consolidate buried low level waste containers. A model burial trench containing simulated clean wastes was dynamically compacted, after which the materials were excavated and compaction quantified. The test determined that under existing success criteria, the bottom tier of stacked B-25 boxes were not being consolidated. A quasi-structural layer was formed midway through the stacked boxes, which absorbed the compactive energy. Resulting from these observations and the data collected, a new success criterion is recommended which depends on the relative displacement per drop. The test successfully demonstrated that dynamic compaction will consolidate buried metal boxes

The Application of GPR in Florida for Detecting Forensic Burials

Energy Technology Data Exchange (ETDEWEB)

S. K. Koppenjan; J. J. Schultz; S. Ono; H. Lee

2003-01-01

A study was performed at the University of Florida to measure ground penetrating radar(GPR) performance for detecting forensic burials. In controlled scenarios, 24 burials were constructed with pig cadavers. Two soils were utilized to represent two of the most common soil orders in Florida: an Entisol and an Ultisol. Graves were monitored on a monthly basis for time periods up to 21 months with grid data acquired with pulsed and swept-frequency GPR systems incorporating several different frequency antennas. A small subset of the graves was excavated to assess decomposition and relate to the GPR images during the test. The grave anomalies in the GPR depth profiles became less distinctive over time due to body decomposition and settling of the disturbed soil (backfill) as it compacted. Soil type was a major factor. Grave anomalies became more difficult to recognize over time for deep targets that were within clay. Forensic targets that were in sandy soil were recognized for the duration of this study. Time elapsed imagery will be presented to elucidate the changes, or lack thereof, of grave anomalies over the duration of this study. Further analysis was performed using Synthetic Aperture Radar (SAR) reconstruction of images in 2-D and 3-D.

Application of biological barriers in maintaining the integrity of radioactivity in shallow burial grounds

International Nuclear Information System (INIS)

Cline, J.F.

1979-05-01

Stabilization of a shallow burial site requires some means of keeping buried radioactive wastes in place and preventing the movement of radioactive elements into the biosphere by various vectors present in the soil covering the burial site. By placing a barrier between the surface of the soil and the buried wastes, it would be possible to isolate the wastes from the biosphere and eliminate the movement of radioactive elements into the environment. An effective biobarrier would make it possible to grow plants over the buried wastes regardless of rooting habits; the plants would stabilize the surface soil, prevent wind erosion, and transpire soil water back into the air, thus preventing it from percolating downward through the buried wastes. This report summarizes the finding of a study undertaken to determine the effectiveness of natural cobblestones as a long-term biobarrier. In the initial field study, we investigated whether a thick layer of cobblestones would prevent plant roots and burrowing animals from reaching contaminated materials and transferring radionuclides to the soil surface. In a subsequent greenhouse study, three modifications of the cobblestone barrier were tested, including the addition of another layer of stones, one of asphalt, and one of a root toxin. These data show that cobblestone can be effective as a barrier to burrowing animals and insects, but not totally effective as a barrier to plant roots. Because of variable weather patterns at Hanford, five to six year studies are recommended for further studies on the effectiveness of different materials as biobarriers to radioactive substances. Stone size appeared to affect the plants' rate of root growth since root growth slowed in the air spaces between stones. Root toxin was 100% effective as a means of keeping roots out of the buried waste; this method could be used as a barrier modification where no plant cover is needed

TruFit Plug for Repair of Osteochondral Defects-Where Is the Evidence? Systematic Review of Literature.

Science.gov (United States)

Verhaegen, J; Clockaerts, S; Van Osch, G J V M; Somville, J; Verdonk, P; Mertens, P

2015-01-01

Treatment of osteochondral defects remains a challenge in orthopedic surgery. The TruFit plug has been investigated as a potential treatment method for osteochondral defects. This is a biphasic scaffold designed to stimulate cartilage and subchondral bone formation. The aim of this study is to investigate clinical, radiological, and histological efficacy of the TruFit plug in restoring osteochondral defects in the joint. We performed a systematic search in five databases for clinical trials in which patients were treated with a TruFit plug for osteochondral defects. Studies had to report clinical, radiological, or histological outcome data. Quality of the included studies was assessed. Five studies describe clinical results, all indicating improvement at follow-up of 12 months compared to preoperative status. However, two studies reporting longer follow-up show deterioration of early improvement. Radiological evaluation indicates favorable MRI findings regarding filling of the defect and incorporation with adjacent cartilage at 24 months follow-up, but conflicting evidence exists on the properties of the newly formed overlying cartilage surface. None of the included studies showed evidence for bone ingrowth. The few histological data available confirmed these results. There are no data available that support superiority or equality of TruFit compared to conservative treatment or mosaicplasty/microfracture. Further investigation is needed to improve synthetic biphasic implants as therapy for osteochondral lesions. Randomized controlled clinical trials comparing TruFit plugs with an established treatment method are needed before further clinical use can be supported.

URBAN STREAM BURIAL INCREASES WATERSHED-SCALE NITRATE EXPORT

Science.gov (United States)

Nitrogen (N) uptake in streams is an important ecosystem service that may be affected by the widespread burial of streams in stormwater pipes in urban watersheds. We predicted that stream burial reduces the capacity of streams to remove nitrate (NO3-) from the water column by in...

Design comparisons of TRU burner cores with similar sodium void worth

International Nuclear Information System (INIS)

Sang Ji, Kim; Young Il, Kim; Young Jin, Kim; Nam Zin, Cho

2001-01-01

This study summarizes the neutronic performance and fuel cycle behavior of five geometrically-different transuranic (TRU) burner cores with similar low sodium void reactivity. The conceptual cores encompass core geometries for annular, two-region homogeneous, dual pin type, pan-shaped and H-shaped cores. They have been designed with the same assembly specifications and managed to have similar end-of-cycle sodium void reactivities and beginning-of-cycle peak power densities through the changes in the core size and configuration. The requirement of low sodium void reactivity is shown to lead each design concept to characteristic neutronics performance and fuel cycle behavior. The H-/pan-shaped cores allow the core compaction as well as higher rate of TRU burning. (author)

Research and development for treatment and disposal technologies of TRU waste

International Nuclear Information System (INIS)

Kamei, Gento; Honda, Akira; Mihara, Morihiro; Oda, Chie; Murakami, Hiroshi; Masuda, Kenta; Yamaguchi, Kohei; Nakanishi, Hiroshi; Sasaki, Ryoichi; Ichige, Satoru; Takahashi, Kuniaki; Meguro, Yoshihiro; Yamaguchi, Hiromi; Aoyama, Yoshio

2007-09-01

After the publication of the 2nd progress report of geological disposal of TRU waste in Japan, policy and general scheme of future study for the waste disposal in Japan was published by ANRE and JAEA. This annual report summarized aim and progress of individual problem, which was assigned into JAEA in the published policy and general scheme. The problems are as follows; characteristics of TRU waste and its geologic disposal, treatment and waste production, quality control and inspection methodology for waste, mechanical analysis of near-field, data acquisition and preparation on radionuclides migration, cementitious material transition, bentonite and rock alteration in alkaline solution, nitrate effect, performance assessment of the disposal system and decomposition of nitrate as an alternative technology. (author)

T-Rex system for operation in TRU, LLW, and hazardous zones

International Nuclear Information System (INIS)

Kline, H.M.; Andreycheck, T.P.; Beeson, B.K.

1995-01-01

T-Rex stands for Transuranic Storage Area Remote Excavator that is dedicated to the retrieval of above ground waste containers and overburden at the Radioactive Waste Management Complex (RWMC) located at the Idaho National Engineering Laboratory. There are a number of sites around the world containing (transuranic) (TRU), low level (LLW), and hazardous wastes that requires teleoperated, heavy lift manipulators with long reach and high precision to handle the materials stored there. Remote operation of equipment will reduce the risk to personnel to as-low-as-reasonably-achievable (ALARA) levels. The T-Rex is designed to fulfill this requirement at relatively low cost through the integration of a production front shovel excavator with a control system, local and remote operator control stations, a closed-circuit television system (CCTV), and multiple end effectors with quick changeout capability. This paper describes the conversion of an off-the-shelf excavator to a machine utilizing a modified hydraulic system, an integrated onboard remote control system, CCTV system, collision avoidance system, and a remote control station

Software documentation for TRU certification program

International Nuclear Information System (INIS)

CLINTON, R.

1999-01-01

The document provides validation information for software used to support TRU operational activities. Calculations were performed using a spreadsheet application. This document provides information about the usage of the software application, Microsoft(reg s ign) Excel. Microsoft(reg s ign) Excel spreadsheets were used to perform specific calculations to determine the amount of containers to visually examine and to perform analyses on container head-gas data. Contained in this document are definitions of formulas and variables with relation to the Excel codes used. Also, a demonstration is provided using predetermined values to obtain predetermined results

TRU transmutation using ThO2-UO2 and fully ceramic micro-encapsulated fuels in LWR fuel assemblies

International Nuclear Information System (INIS)

Bae, Gonghoon; Hong, Sergi

2012-01-01

The objective of this work is to design new LWR fuel assemblies which are able to efficiently destroy TRU (transuranics) nuclide without degradation of safety aspects by using ThO 2 -UO 2 fuel pins and FCM (Fully Ceramic Micro-encapsulated) fuel pins containing TRU fuel particles. Thorium was mixed to UO 2 in order to reduce the generation of plutonium nuclides and to save the uranium resources in the UO 2 pins. Additionally, the use of thorium contributes to the extension of the fuel cycle length. All calculations were performed by using DeCART (Deterministic Core Analysis based on Ray Tracing) code. The results show that the new concept of fuel assembly has the TRU destruction rates of ∼40% and ∼25% per 1200 EFPD (Effective Full Power Day) over the TRU FCM pins and the overall fuel assembly, respectively, without degradation of FTC and MTC

A preliminary evaluation of certain NDA techniques for RH-TRU characterization

Energy Technology Data Exchange (ETDEWEB)

Hartwell, J.K.; Yoon, W.Y.; Peterson, H.K. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

1997-11-01

This report presents the results of modeling efforts to evaluate selected NDA assay methods for RH-TRU waste characterization. The target waste stream was Content Code 104/107 113-liter waste drums that comprise the majority of the INEL`s RH-TRU waste inventory. Two NDA techniques are treated in detail. One primary NDA technique examined is gamma-ray spectrometry to determine the drum fission and activation product content, and fuel sample inventory calculations using the ORIGEN code to predict the total drum inventory. A heavily shielded and strongly collimated HPGe spectrometer system was designed using MCNP modeling. Detection limits and expected precision of this approach were estimated by a combination of Monte Carlo modeling and synthetic gamma-ray spectrum generation. This technique may allow the radionuclide content of these wastes to be determined with relative standard deviations of 20 to 50% depending on the drum matrix and radionuclide. The INEL Passive/Active Neutron (PAN) assay system is the second primary technique considered. A shielded overpack for the 113-liter CC104/107 RH-TRU drums was designed to shield the PAN detectors from excessive gamma radiation. MCNP modeling suggests PAN detection limits of about 0.06 g {sup 235}U and 0.04 g {sup 239}Pu during active assays. 12 refs., 2 figs., 6 tabs.

Remedial investigation work plan for Bear Creek Valley Operable Unit 1 (S-3 Ponds, Boneyard/Burnyard, Oil Landfarm, Sanitary Landfill I, and the Burial Grounds, including Oil Retention Ponds 1 and 2) at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee. Volume 1, Main text

International Nuclear Information System (INIS)

1994-03-01

This document refers to data concerning the Environmental Restoration Program implemented at the Oak Ridge Y-12 plant. Topics discussed include: Remediation plans for the burial grounds, sanitary landfill I, oil retention ponds, S-3 ponds, and the boneyard/burnyard at Y-12. This document also contains information about the environmental policies regulating the remediation

Radionuclide-migration model for buried waste at the Savannah River Plant

International Nuclear Information System (INIS)

King, C.M.; Root, R.W. Jr.

1982-01-01

Solid waste has been buried at the Savannah River Plant burial ground since 1953. The solid waste is contaminated with alpha-emitting transuranium (TRU) nuclides, with beta-gamma-emitting activation and fission products, and with tritium. To provide guidance for the current use and eventual permanent retirement of the burial site from active service, a radionuclide environmental transport model has been used to project the potential influence on man if the burial site were occupied after decommissioning. The model used to simulate nuclide migration includes the various hydrological, animal, vegetative, atmospheric, and terrestrial pathways in estimating dose to man as a function of time. Specific scenarios include a four-person home farm on the 195-acre burial ground. Key input to the model includes site-specific nuclide migration rates through soil, nuclide distribution coefficients, and site topography. Coupled with literature data on plant and animal concentration factors, transfer coefficients reflecting migration routes are input to a set of linear differential equations for subsequent matrix solution. Output from the model is the nuclide-specific decayed curie intake by man. To discern principal migration routes, model-compartment inventories with time can also be displayed. Dose projections subsequently account for organ concentrations in man for the nuclide of interest. Radionuclide migration has been examined in depth with the dose-to-man model. Movement by vegetative pathways is the primary route for potential dose to man for short-lived isotopes. Hydrological routes provide a secondary scheme for long-lived nuclides. Details of model methodology are reviewed

Soil monitoring instrumentation

International Nuclear Information System (INIS)

Umbarger, C.J.

1980-01-01

The Los Alamos Scientific Laboratory (LASL) has an extensive program for the development of nondestructive assay instrumentation for the quantitative analysis of transuranic (TRU) materials found in bulk solid wastes generated by Department of Energy facilities and by the commercial nuclear power industry. Included are wastes generated in decontamination and decommissioning of outdated nuclear facilities as well as wastes from old waste burial ground exhumation programs. The assay instrumentation is designed to have detection limits below 10 nCi/g wherever practicable. Because of the topic of this workshop, only the assay instrumentation applied specifically to soil monitoring will be discussed here. Four types of soil monitors are described

TruFit Plug for Repair of Osteochondral Defects—Where Is the Evidence? Systematic Review of Literature

Science.gov (United States)

Clockaerts, S.; Van Osch, G.J.V.M.; Somville, J.; Verdonk, P.; Mertens, P.

2015-01-01

Objective: Treatment of osteochondral defects remains a challenge in orthopedic surgery. The TruFit plug has been investigated as a potential treatment method for osteochondral defects. This is a biphasic scaffold designed to stimulate cartilage and subchondral bone formation. The aim of this study is to investigate clinical, radiological, and histological efficacy of the TruFit plug in restoring osteochondral defects in the joint. Design: We performed a systematic search in five databases for clinical trials in which patients were treated with a TruFit plug for osteochondral defects. Studies had to report clinical, radiological, or histological outcome data. Quality of the included studies was assessed. Results: Five studies describe clinical results, all indicating improvement at follow-up of 12 months compared to preoperative status. However, two studies reporting longer follow-up show deterioration of early improvement. Radiological evaluation indicates favorable MRI findings regarding filling of the defect and incorporation with adjacent cartilage at 24 months follow-up, but conflicting evidence exists on the properties of the newly formed overlying cartilage surface. None of the included studies showed evidence for bone ingrowth. The few histological data available confirmed these results. Conclusion: There are no data available that support superiority or equality of TruFit compared to conservative treatment or mosaicplasty/microfracture. Further investigation is needed to improve synthetic biphasic implants as therapy for osteochondral lesions. Randomized controlled clinical trials comparing TruFit plugs with an established treatment method are needed before further clinical use can be supported. PMID:26069706

Alkaline degradation of organic materials contained in TRU wastes under repository conditions

International Nuclear Information System (INIS)

Otsuka, Yoshiki; Banba, Tsunetaka

2007-09-01

Alkaline degradation tests for 9 organic materials were conducted under the conditions of TRU waste disposal: anaerobic alkaline conditions. The tests were carried out at 90degC for 91 days. The sample materials for the tests were selected from the standpoint of constituent organic materials of TRU wastes. It has been found that cellulose and plastic solidified products are degraded relatively easily and that rubbers are difficult to degrade. It could be presumed that the alkaline degradation of organic materials occurs starting from the functional group in the material. Therefore, the degree of degradation difficulty is expected to be dependent on the kinds of functional group contained in the organic material. (author)

Radiolytic decomposition of organic C-14 released from TRU waste

International Nuclear Information System (INIS)

Kani, Yuko; Noshita, Kenji; Kawasaki, Toru; Nishimura, Tsutomu; Sakuragi, Tomofumi; Asano, Hidekazu

2007-01-01

It has been found that metallic TRU waste releases considerable portions of C-14 in the form of organic molecules such as lower molecular weight organic acids, alcohols and aldehydes. Due to the low sorption ability of organic C-14, it is important to clarify the long-term behavior of organic forms under waste disposal conditions. From investigations on radiolytic decomposition of organic carbon molecules into inorganic carbonic acid, it is expected that radiation from TRU waste will decompose organic C-14 into inorganic carbonic acid that has higher adsorption ability into the engineering barriers. Hence we have studied the decomposition behavior of organic C-14 by gamma irradiation experiments under simulated disposal conditions. The results showed that organic C-14 reacted with OH radicals formed by radiolysis of water, to produce inorganic carbonic acid. We introduced the concept of 'decomposition efficiency' which expresses the percentage of OH radicals consumed for the decomposition reaction of organic molecules in order to analyze the experimental results. We estimated the effect of radiolytic decomposition on the concentration of organic C-14 in the simulated conditions of the TRU disposal system using the decomposition efficiency, and found that the concentration of organic C-14 in the waste package will be lowered when the decomposition of organic C-14 by radiolysis was taken into account, in comparison with the concentration of organic C-14 without radiolysis. Our prediction suggested that some amount of organic C-14 can be expected to be transformed into the inorganic form in the waste package in an actual system. (authors)

About the problem of self-burial of radioactive wasters

International Nuclear Information System (INIS)

Kosachevskij, L.Ya.; Syui, L.S.

1999-01-01

Problem dealing with self-burial of finite thickness spherical container with radioactive waste into the melting rock was approached. The elaborated mathematical model in contrast to the available ones takes account of thermal losses in the hard rock and in the melting behind the container as well as, the back heat release at melting hardening. Calculation conducted for the particular case of self-burial into granite demonstrates that accounting of these factors increases essentially the maximum permissible radius when container remains in the solid state and decreases the rate of its burial [ru

Sodium-cooled Fast Reactor Cores using Uranium-Free Metallic Fuels for Maximizing TRU Support Ratio

International Nuclear Information System (INIS)

You, WuSeung; Hong, Ser Gi

2014-01-01

The depleted uranium plays important roles in the SFR burner cores because it substantially contributes to the inherent safety of the core through the negative Doppler coefficient and large delayed neutron. However, the use of depleted uranium as a diluent nuclide leads to a limited value of TRU support ratio due to the generation of TRUs through the breeding. In this paper, we designed sodium cooled fast reactor (SFR) cores having uranium-free fuels 3,4 for maximization of TRU consumption rate. However, the uranium-free fuelled burner cores can be penalized by unacceptably small values of the Doppler coefficient and small delayed neutron fraction. In this work, metallic fuels of TRU-(W or Ni)-Zr are considered to improve the performances of the uranium-free cores. The objective of this work is to consistently compare the neutronic performances of uranium-free sodium cooled fast reactor cores having TRU-Zr metallic fuels added with Ni or W and also to clarify what are the problematic features to be resolved. In this paper, a consistent comparative study of 400MWe sodium cooled burner cores having uranium-based fuels and uranium-free fuels was done to analyze the relative core neutronic features. Also, we proposed a uranium-free metallic fuel based on Nickel. From the results, it is found that tungsten-based uranium-free metallic fuel gives large negative Doppler coefficient due to high resonance of tungsten isotopes but this core has large sodium void worth and small effective delayed neutron fraction while the nickel-based uranium-free metallic fuelled core has less negative Doppler coefficient but smaller sodium void worth and larger effective delayed neutron fraction than the tungsten-based one. On the other hand, the core having TRU-Zr has very high burnup reactivity swing which may be problematic in compensating it using control rods and the least negative Doppler coefficient

Analysis of long-term impacts of TRU waste remaining at generator/storage sites for No Action Alternative 2

International Nuclear Information System (INIS)

Buck, J.W.; Bagaasen, L.M.; Bergeron, M.P.; Streile, G.P.

1997-09-01

This report is a supplement to the Waste Isolation Pilot Plant Disposal-Phase Final Supplemental Environmental Impact Statement (SEIS-II). Described herein are the underlying information, data, and assumptions used to estimate the long-term human-health impacts from exposure to radionuclides and hazardous chemicals in transuranic (TRU) waste remaining at major generator/storage sites after loss of institutional control under No Action Alternative 2. Under No Action Alternative 2, TRU wastes would not be emplaced at the Waste Isolation Pilot Plant (WIPP) but would remain at generator/storage sites in surface or near-surface storage. Waste generated at smaller sites would be consolidated at the major generator/storage sites. Current TRU waste management practices would continue, but newly generated waste would be treated to meet the WIPP waste acceptance criteria. For this alternative, institutional control was assumed to be lost 100 years after the end of the waste generation period, with exposure to radionuclides and hazardous chemicals in the TRU waste possible from direct intrusion and release to the surrounding environment. The potential human-health impacts from exposure to radionuclides and hazardous chemicals in TRU waste were analyzed for two different types of scenarios. Both analyses estimated site-specific, human-health impacts at seven major generator/storage sites: the Hanford Site (Hanford), Idaho National Engineering and Environmental Laboratory (INEEL), Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), Oak Ridge National Laboratory (ORNL), Rocky Flats Environmental Technology Site (RFETS), and Savannah River Site (SRS). The analysis focused on these seven sites because 99 % of the estimated TRU waste volume and inventory would remain there under the assumptions of No Action Alternative 2

GPR and ERT detection and characterization of a mass burial, Spanish Civil War, Northern Spain.

Science.gov (United States)

Rubio-Melendi, David; Gonzalez-Quirós, Andrés; Roberts, Daniel; García García, María Del Carmen; Caunedo Domínguez, Amaya; Pringle, Jamie K; Fernández-Álvarez, José-Paulino

2018-06-01

Around 27,000 people were killed in the province of Asturias during the Spanish Civil War, with several thousands killed after the war ended. There are currently over 2,000 known mass burial locations throughout Spain, but many more are unknown. Geophysics is a useful tool employed to help in the active attempts to document and improve knowledge about victims from this conflict. This paper details a non-invasive study of the Cementerio de El Salvador, in the city of Oviedo, Northern Spain. Part of the cemetery contains a known mass burial with approximately 1,300 individuals from the Spanish Civil War and post-war repression eras. Multi-frequency near-surface geophysical techniques were undertaken, after permission, to enhance knowledge about which, if any, techniques should be used to detect, delineate and analyse such mass graves. Multi-frequency (250MHz and 500MHz) ground-penetrating radar surveys were acquired together with 2D and 3D Electrical Resistivity Tomography datasets. The results have established the limits of the mass grave and improve the knowledge of the internal mass grave structure. The paper also shows the importance of considering the climatic conditions during data acquisition. This has important implications for the successful detection of recent historical mass burials using near-surface geophysics. Copyright © 2018 Elsevier B.V. All rights reserved.

Packaging design criteria modified fuel spacer burial box. Revision 1

International Nuclear Information System (INIS)

Stevens, P.F.

1994-01-01

Various Hanford facilities must transfer large radioactively contaminated items to burial/storage. Presently, there are eighteen Fuel Spacer Burial Boxes (FSBBs) available on the Hanford Site for transport of such items. Previously, the FSBBS were transported from a rail car to the burial trench via a drag-off operation. To allow for the lifting of the boxes into the burial trench, it will be necessary to improve the packagings lifting attachments and provide structural reinforcement. Additional safety improvements to the packaging system will be provided by the addition of a positive closure system and package ventilation. FSBBs that are modified in such a manner are referred to as Modified Fuel Spacer Burial Boxes (MFSBs). The criteria provided by this PDC will be used to demonstrate that the transfer of the MFSB will provide an equivalent degree of safety as would be provided by a package meeting offsite transportation requirements. This fulfills the onsite transportation safety requirements implemented in WHC-CM-2-14, Hazardous Material Packaging and Shipping. A Safety Analysis Report for Packaging (SARP) will be prepared to evaluate the safety of the transfer operation. Approval of the SARP is required to authorize transfer. Criteria are also established to ensure burial requirements are met

Optimization of hybrid-type instrumentation for Pu accountancy of U/TRU ingot in pyroprocessing.

Science.gov (United States)

Seo, Hee; Won, Byung-Hee; Ahn, Seong-Kyu; Lee, Seung Kyu; Park, Se-Hwan; Park, Geun-Il; Menlove, Spencer H

2016-02-01

One of the final products of pyroprocessing for spent nuclear fuel recycling is a U/TRU ingot consisting of rare earth (RE), uranium (U), and transuranic (TRU) elements. The amounts of nuclear materials in a U/TRU ingot must be measured as precisely as possible in order to secure the safeguardability of a pyroprocessing facility, as it contains the most amount of Pu among spent nuclear fuels. In this paper, we propose a new nuclear material accountancy method for measurement of Pu mass in a U/TRU ingot. This is a hybrid system combining two techniques, based on measurement of neutrons from both (1) fast- and (2) thermal-neutron-induced fission events. In technique #1, the change in the average neutron energy is a signature that is determined using the so-called ring ratio method, according to which two detector rings are positioned close to and far from the sample, respectively, to measure the increase of the average neutron energy due to the increased number of fast-neutron-induced fission events and, in turn, the Pu mass in the ingot. We call this technique, fast-neutron energy multiplication (FNEM). In technique #2, which is well known as Passive Neutron Albedo Reactivity (PNAR), a neutron population's changes resulting from thermal-neutron-induced fission events due to the presence or absence of a cadmium (Cd) liner in the sample's cavity wall, and reflected in the Cd ratio, is the signature that is measured. In the present study, it was considered that the use of a hybrid, FNEM×PNAR technique would significantly enhance the signature of a Pu mass. Therefore, the performance of such a system was investigated for different detector parameters in order to determine the optimal geometry. The performance was additionally evaluated by MCNP6 Monte Carlo simulations for different U/TRU compositions reflecting different burnups (BU), initial enrichments (IE), and cooling times (CT) to estimate its performance in real situations. Copyright © 2015 Elsevier Ltd. All

Nondestructive assay of TRU waste using gamma-ray active and passive computed tomography

International Nuclear Information System (INIS)

Roberson, G.P.; Decman, D.; Martz, H.; Keto, E.R.; Johansson, E.M.

1995-01-01

The authors have developed an active and passive computed tomography (A and PCT) scanner for assaying radioactive waste drums. Here they describe the hardware components of their system and the software used for data acquisition, gamma-ray spectroscopy analysis, and image reconstruction. They have measured the performance of the system using ''mock'' waste drums and calibrated radioactive sources. They also describe the results of measurements using this system to assay a real TRU waste drum with relatively low Pu content. The results are compared with X-ray NDE studies of the same TRU waste drum as well as assay results from segmented gamma scanner (SGS) measurements

A process of spent nuclear fuel treatment with the interim storage of TRU by use amidic extractants

International Nuclear Information System (INIS)

Tachimori, Shoichi; Suzuki, Shinichi; Sasaki, Yuji

2001-01-01

A new chemical process, ARTIST process, is proposed for the treatment of spent nuclear fuel. The main concept of the ARTIST process is to recover and stock separately all actinides, uranium and a mixture of transuranics, and to dispose fission products. The process composed of two main steps, a uranium exclusive isolation and a total recovery of transuranium elements (TRU); which copes with the nuclear non-proliferation measures, and additional processes. Both actinide products are solidified by calcination and allowed to the interim storage for future utilization. These separations are achieved by use of amidic extractants in accord with the CHON principle. The technical feasibility of the ARTIST process was explained by the experimental results of both the branched-alkyl monoamides in extracting uranium and suppressing the extraction of tetravalent actinides due to the steric effect and the diglycolic amide in thorough extraction of all TRU by tridentate coordination. When these TRU are requested to put into reactors, LWR or FBR, for power generation or the Accelerator-Driven System (ADS) for transmutation, lanthanides are to be removed from TRU by utilizing a soft nitrogen donor ligand. (author)

Modeling and preliminary analysis on the temperature profile of the (TRU-Zr)-Zr dispersion fuel rod for HYPER

International Nuclear Information System (INIS)

Lee, B. W.; Hwang, W.; Lee, B. S.; Park, W. S.

2000-01-01

Either TRU-Zr metal alloy or (TRU-Zr)-Zr dispersion fuel is considered as a blanket fuel for HYPER(Hybrid Power Extraction Reactor). In order to develop the code for dispersion fuel rod performance analysis under steady state condition, the fuel temperature distribution model which is the one of the most important factors in a fuel performance code has been developed in this paper,. This developed model computes the one dimensional radial temperature distribution of a cylindrical fuel rod. The temperature profile results by this model are compared with the temperature distributions of U 3 Si-A1 dispersion fuel and TRU-Zr metal alloy fuel. This model will be installed in performance analysis code for dispersion fuel

Demonstration of Entrained Solids and Sr/TRU Removal Processes with Archived AN-107 Waste

International Nuclear Information System (INIS)

Hallen, R.T.; Brooks, K.P.; Jagoda, L.K.

2000-01-01

Archived AN-107 waste was used to evaluate entrained solids removal, Sr/TRU decontamination of supernatant, and Sr/TRU solids removal. Even though most of the entrained solids had been previously removed from the archived sample, the residual entrained solids rapidly fouled the filter element resulting in very poor filter performance. An attempt to run at higher pressure resulted in more fouling, and reduced filter performance. Filtration efforts to remove entrained solids were abandoned and the waste was treated for Sr/TRU removal with the entrained solids present. The new processing scheme for Sr/TRU removal involving precipitation by added strontium and permanganate worked well. The decontamination factors for Sr and TRU components were significantly greater than the ILAW DF requirements for higher reagent concentrations of 1M hydroxide, 0.075M Sr, and 0.05M permanganate and lower reagent concentrations of 0.8M hydroxide, 0.05M Sr, and 0.03M permanganate. These results support the use of lower concentration of reagent additions in future tests. Optimization studies should be conducted to examine the reduction in added hydroxide from 1M to 0.5 M, reduction of Sr from 0.075M to 0.05M, and reduction in permanganate from 0.05M to 0.03M and the impact this reduction has on filtration performance with new samples from Tank AN-107. The combined entrained solids and Sr/TRU precipitate were successfully filtered in the single element, crossflow filtration unit. The filtrate flux was high, >0.1 gpm/ft 2 , at the initial test conditions of 53 psi and 11.2ft/s for the treated archived AN-107 sample. The filter flux rate dropped significantly with time as testing progressed and appears to be a result of shearing the agglomerated solids and fouling of the filter element by the resulting fine particles. The relatively low clean water flux rates obtained at the end of the test also indicate filter fouling. Chemical cleaning was required to restore clean water flux rates to pre

Terminating Safeguards on Excess Special Nuclear Material: Defense TRU Waste Clean-up and Nonproliferation - 12426

Energy Technology Data Exchange (ETDEWEB)

Hayes, Timothy [Los Alamos National Laboratory, Carlsbad Operations Group (United States); Nelson, Roger [Department Of Energy, Carlsbad Operations Office (United States)

2012-07-01

The Department of Energy (DOE) and the National Nuclear Security Administration (NNSA) manages defense nuclear material that has been determined to be excess to programmatic needs and declared waste. When these wastes contain plutonium, they almost always meet the definition of defense transuranic (TRU) waste and are thus eligible for disposal at the Waste Isolation Pilot Plant (WIPP). The DOE operates the WIPP in a manner that physical protections for attractiveness level D or higher special nuclear material (SNM) are not the normal operating condition. Therefore, there is currently a requirement to terminate safeguards before disposal of these wastes at the WIPP. Presented are the processes used to terminate safeguards, lessons learned during the termination process, and how these approaches might be useful for future defense TRU waste needing safeguards termination prior to shipment and disposal at the WIPP. Also described is a new criticality control container, which will increase the amount of fissile material that can be loaded per container, and how it will save significant taxpayer dollars. Retrieval, compliant packaging and shipment of retrievably stored legacy TRU waste has dominated disposal operations at WIPP since it began operations 12 years ago. But because most of this legacy waste has successfully been emplaced in WIPP, the TRU waste clean-up focus is turning to newly-generated TRU materials. A major component will be transuranic SNM, currently managed in safeguards-protected vaults around the weapons complex. As DOE and NNSA continue to consolidate and shrink the weapons complex footprint, it is expected that significant quantities of transuranic SNM will be declared surplus to the nation's needs. Safeguards termination of SNM varies due to the wide range of attractiveness level of the potential material that may be directly discarded as waste. To enhance the efficiency of shipping waste with high TRU fissile content to WIPP, DOE designed an

Waste Disposition Issues and Resolutions at the TRU Waste Processing Center at Oak Ridge TN

International Nuclear Information System (INIS)

Gentry, R.

2009-01-01

This paper prepared for the Waste Management Conference 2009 provides lessons learned from the Transuranic (TRU) Waste Processing Center (TWPC) associated with development of approaches used to certify and ensure disposition of problematic TRU wastes at the Waste Isolation Pilot Plant (WIPP) site. The TWPC is currently processing the inventory of available waste TRU waste at the Oak Ridge National Lab (ORNL). During the processing effort several waste characteristics were identified/discovered that did not conform to the normal standards and processes for disposal at WIPP. Therefore, the TWPC and ORNL were challenged with determining a path forward for this problematic, special case TRU wastes to ensure that they can be processed, packaged, and shipped to WIPP. Additionally, unexpected specific waste characteristics have challenged the project to identify and develop processing methods to handle problematic waste. The TWPC has several issues that have challenged the projects ability to process RH Waste. High Neutron Dose Rate resulting from both Californium and Curium in the waste stream challenge the RH-TRU 72-B limit for dose rate measured from the side of the package under normal conditions of transport, as specified in Chapter 5.0 of the RH-TRU 72-B SAR (i.e., ≤10 mrem/hour at 2 meters). Difficult to process waste in the hot cell has introduced processing and handling difficulties included problems associated with the disposition of prohibited items that fall out of the waste stream such as liquids, aerosol cans, etc. Lastly, multiple waste streams require characterization and AK challenge the ability to generate dose-to curie models for the waste. Repackaging is one solution to the high neutron dose rate issue. In parallel, an effort is underway to request a change to the TRAMPAC requirements to allow shielding in the drum or canister to reduce the impact of the high neutron dose rates. Due diligence on supporting AK efforts is important in ensuring adequate

Final Environmental Impact Statement for Treating Transuranic (TRU)/Alpha Low-level Waste at the Oak Ridge National Laboratory Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

N/A

2000-06-30

The DOE proposes to construct, operate, and decontaminate/decommission a TRU Waste Treatment Facility in Oak Ridge, Tennessee. The four waste types that would be treated at the proposed facility would be remote-handled TRU mixed waste sludge, liquid low-level waste associated with the sludge, contact-handled TRU/alpha low-level waste solids, and remote-handled TRU/alpha low-level waste solids. The mixed waste sludge and some of the solid waste contain metals regulated under the Resource Conservation and Recovery Act and may be classified as mixed waste. This document analyzes the potential environmental impacts associated with five alternatives--No Action, the Low-Temperature Drying Alternative (Preferred Alternative), the Vitrification Alternative, the Cementation Alternative, and the Treatment and Waste Storage at Oak Ridge National Laboratory (ORNL) Alternative.

Safety assessment for the above ground storage of Cadmium Safety and Control Rods at the Solid Waste Management Facility

International Nuclear Information System (INIS)

Shaw, K.W.

1993-11-01

The mission of the Savannah River Site is changing from radioisotope production to waste management and environmental restoration. As such, Reactor Engineering has recently developed a plan to transfer the safety and control rods from the C, K, L, and P reactor disassembly basin areas to the Transuranic (TRU) Waste Storage Pads for long-term, retrievable storage. The TRU pads are located within the Solid Waste Management Facilities at the Savannah River Site. An Unreviewed Safety Question (USQ) Safety Evaluation has been performed for the proposed disassembly basin operations phase of the Cadmium Safety and Control Rod Project. The USQ screening identified a required change to the authorization basis; however, the Proposed Activity does not involve a positive USQ Safety Evaluation. A Hazard Assessment for the Cadmium Safety and Control Rod Project determined that the above-ground storage of the cadmium rods results in no change in hazard level at the TRU pads. A Safety Assessment that specifically addresses the storage (at the TRU pads) phase of the Cadmium Safety and Control Rod Project has been performed. Results of the Safety Assessment support the conclusion that a positive USQ is not involved as a result of the Proposed Activity

About One of Burials of Novotitorovka Culture From the Territory of Kuban

Directory of Open Access Journals (Sweden)

Mariya A. Balabanova

2017-03-01

Full Text Available The article is devoted to the burial complex and the skull of the Novotitorovka culture from burial no. 35 of the Ovalny burial mound, Kalininsky district of the Krasnodar region. The burial itself was non-inventory, but it was synchronous with burial no. 26. Both burials were excavated from the level of the ancient surface and covered by the same barrow. The bones from the studied burial belonged to a young man, who died at the age of 20-25. His craniological type is characterized by meso-dolichocrania, ellipsoidal vertical norm, the average width of forehead, wide and low face, orthognathy-like in a vertical plane and slightly profiled at the level of low eye sockets. The face is also characterized by narrow and sharply protruding nasal bones. The article also deals with the possible relationship between the tribes of the Novotitorovka culture and the Azov-Black Sea sites of Catacomb culture. This conclusion is based on the results of intergroup comparison by the method of canonical analysis. The studied skull of the Novotitorovka culture has a morphological complex that characterizes the groups of burials of the Catacomb culture localized on the terraces of the Ingul river and on the terraces of the Don river left bank. This conclusion calls into question the archaeologists’ hypothesis on the connection of the the Novotitorovka culture with the tribes of the Novosvobodnenskaya culture and the Maykop culture.

78 FR 76574 - Burial Benefits

Science.gov (United States)

2013-12-18

..., Congress' clear motivation was to make burial benefits ``easier to administer, i.e., through existing VA...'' means any action taken to honor the memory of a deceased individual. 38 CFR 38.600. 3.1701 Deceased...

Effects of urban stream burial on nitrogen uptake and ...

Science.gov (United States)

Urbanization has resulted in extensive burial and channelization of headwater streams, yet little is known about impacts on stream ecosystem functions critical for reducing downstream nitrogen pollution. To characterize the biogeochemical impact of stream burial, we measured NO3- uptake, using 15N-NO3- isotope tracer releases, and whole stream metabolism, during four seasons in three paired buried and open streams reaches within the Baltimore Ecosystem Study Long-term Ecological Research Network. Stream burial increased NO3- uptake lengths, by a factor of 7.5 (p < 0.01) and decreased nitrate uptake velocity and areal nitrate uptake rate by factors of 8.2 (p = 0.01) and 9.6 (p < 0.001), respectively. Stream burial decreased gross primary productivity by a factor of 9.2 (p < 0.05) and decreased ecosystem respiration by a factor of 4.2 (p = 0.06). From statistical analysis of Excitation Emissions Matrices (EEMs), buried streams were also found to have significantly less labile dissolved organic matter. Furthermore, buried streams had significantly lower transient storage and water temperatures. Overall, differences in NO3- uptake and metabolism were primarily explained by decreased transient storage and light availability in buried streams. We estimate that stream burial increases daily watershed nitrate export by as much as 500% due to decreased in-stream retention and may considerably decrease carbon export via decreased primary production. These results

Leaching properties of solidified TRU waste forms

International Nuclear Information System (INIS)

Colombo, P.; Neilson, R.M. Jr.

1979-01-01

Safety analysis of waste forms requires an estimate of the ability of these forms to retain activity in the disposal environment. This program of leaching tests will determine the leaching properties of TRU contaminated incinerator ash waste forms using hydraulic cement, urea--formaldehyde, bitumen, and vinyl ester--styrene as solidification agents. Three types of leaching tests will be conducted, including both static and flow rate. Five generic groundwaters will be used. Equipment and procedures are described. Experiments have been conducted to determine plate out of 239 Pu, counter efficiency, and stability of counting samples

Waste Isolation Pilot Plant TruDock crane system analysis

International Nuclear Information System (INIS)

Morris, B.C.; Carter, M.

1996-10-01

The WIPP TruDock crane system located in the Waste Handling Building was identified in the WIPP Safety Analysis Report (SAR), November 1995, as a potential accident concern due to failures which could result in a dropped load. The objective of this analysis is to evaluate the frequency of failure of the TruDock crane system resulting in a dropped load and subsequent loss of primary containment, i.e. drum failure. The frequency of dropped loads was estimated to be 9.81E-03/year or approximately one every 102 years (or, for the 25% contingency, 7.36E-03/year or approximately one every 136 years). The dominant accident contributor was the failure of the cable/hook assemblies, based on failure data obtained from NUREG-0612, as analyzed by PLG, Inc. The WIPP crane system undergoes a rigorous test and maintenance program, crane operation is discontinued following any abnormality, and the crane operator and load spotter are required to be trained in safe crane operation, therefore it is felt that the WIPP crane performance will exceed the data presented in NUREG-0612 and the estimated failure frequency is felt to be conservative

Hydrogen venting characteristics of commercial carbon-composite filters and applications to TRU waste

International Nuclear Information System (INIS)

Callis, E.L.; Marshall, R.S.; Cappis, J.H.

1997-04-01

The generation of hydrogen (by radiolysis) and of other potentially flammable gases in radioactive wastes which are in contact with hydrogenous materials is a source of concern, both from transportation and on-site storage considerations. Because very little experimental data on the generation and accumulation of hydrogen was available in actual waste materials, work was initiated to experimentally determine factors affecting the concentration of hydrogen in the waste containers, such as the hydrogen generation rate, (G-values) and the rate of loss of hydrogen through packaging and commercial filter-vents, including a new design suitable for plastic bags. This report deals only with the venting aspect of the problem. Hydrogen venting characteristics of two types of commercial carbon-composite filter-vents, and two types of PVC bag closures (heat-sealed and twist-and-tape) were measured. Techniques and equipment were developed to permit measurement of the hydrogen concentration in various layers of actual transuranic (TRU) waste packages, both with and without filter-vents. A test barrel was assembled containing known configuration and amounts of TRU wastes. Measurements of the hydrogen in the headspace verified a hydrogen release model developed by Benchmark Environmental Corporation. These data were used to calculate revised wattage Emits for TRU waste packages incorporating the new bag filter-vent

U-Th Burial Dates on Ostrich Eggshell

Science.gov (United States)

Sharp, W. D.; Fylstra, N. D.; Tryon, C. A.; Faith, J. T.; Peppe, D. J.

2015-12-01

Obtaining precise and accurate dates at archaeological sites beyond the range of radiocarbon dating is challenging but essential for understanding human origins. Eggshells of ratites (large flightless birds including ostrich, emu and others) are common in many archaeological sequences in Africa, Australia and elsewhere. Ancient eggshells are geochemically suitable for the U-Th technique (1), which has about ten times the range of radiocarbon dating (>500 rather than 50 ka), making eggshells attractive dating targets. Moreover, C and N isotopic studies of eggshell provide insights into paleovegetation and paleoprecipitation central to assessing past human-environment interactions (2,3). But until now, U-Th dates on ratite eggshell have not accounted for the secondary origin of essentially all of their U. We report a novel approach to U-Th dating of eggshell that explicitly accounts for secondary U uptake that begins with burial. Using ostrich eggshell (OES) from Pleistocene-Holocene east African sites, we have measured U and 232Th concentration profiles across OES by laser ablation ICP-MS. U commonly peaks at 10s to 100s of ppb and varies 10-fold or more across the ~2 mm thickness of OES, with gradients modulated by the layered structure of the eggshell. Common Th is high near the shell surfaces, but low in the middle "pallisade" layer of OES, making it optimal for U-Th dating. We determine U-Th ages along the U concentration gradient by solution ICP-MS analyses of two or more fractions of the pallisade layer. We then estimate OES burial dates using a simple model for diffusive uptake of uranium. Comparing such "U-Th burial dates" with radiocarbon dates for OES calcite from the same shells, we find good agreement in 7 out of 9 cases, consistent with rapid burial and confirming the accuracy of the approach. The remaining 2 eggshells have anomalous patterns of apparent ages that reveal they are unsuitable for U-Th dating, thereby providing reliability criteria innate

Migration of tritium from a nuclear waste burial site

International Nuclear Information System (INIS)

Hawkins, R.H.

1975-09-01

The Savannah River Plant (SRP) has routinely and continuously monitored the local environment (land, water, air, flora, and fauna) since 1951. As part of this intensive program, a three-part study was made to assess the tritium migration from an onsite burial ground for solid nuclear wastes and the resulting dose-to-man. A major source of tritium is buried, massive, Li-Al residues (referred to as melts) from the thermal extraction step in the SRP tritium production process. A melt with its extraction crucible and lid were immersed in water to measure the amounts of tritium released as HTO and HT to the water and to air. The result was a rapid release of 23 curies, of which approximately 99 percent was HTO that remained in the immersion water, and 1 percent was HT that passed into the air. (auth)

Dialectics of Burial and Teritoriality in Barclays Ayakoroma's A ...

African Journals Online (AJOL)

This paper is conceived to investigate the subjects of death, burial, pride and territorial supremacy in African drama with special focus on A Matter of Honour by Barclays Ayakoroma. The study becomes crucial because the question of burial and struggle over rights of possession of a corpse by two parties has become a ...

About the burial of nuclear power plants, damaged or in the process of decommissioning

International Nuclear Information System (INIS)

Elbrond, J.

1994-01-01

Some underground mining methods leave deep empty holes in the earth's surface behind them. In this paper it is described how to use such mining methods for the burial of damaged nuclear power plants and for the decommissioning by burial of nuclear reactors. The design of a new power plant should be integrated with that of an escapeway - an underground arrangement for burial. The described mining methods are block caving for catastrophy burial, and various stoping methods for planned burial and decommissioning. Blind shaft sinking by full face boring machines for burial and decommissioning of the reactor vessel is also described. All the described activities of mining and shaft sinking are well known. The total costs of burial by these methods are estimated using standard mining industry cost data. These include the costs for normal mine ventilation and groundwater control. However, the estimates of the cost and duration do not include the capital and operational costs of the pre- and post burial activities of ventilation and groundwater control related to the radioactivity. (author)

20 CFR 416.1231 - Burial spaces and certain funds set aside for burial expenses.

Science.gov (United States)

2010-04-01

... children and step-children; an individual's brothers, sisters, parents, adoptive parents, and the spouses... are set aside for the burial arrangements of the eligible child's ineligible parent or parent's spouse... separation; i.e., a circumstance beyond an individual's control which makes conversion/separation impossible...

Problems of solidificated radioactive wastes burial into deep geological structures

International Nuclear Information System (INIS)

Kedrovskij, O.L.; Leonov, E.A.; Romadin, N.M.; Shishcits, I.Yu.

1981-01-01

Perspectives are noted of the radioactive wastes burial into deep geopogical structures. For these purposes it has been proposed to investigate severap types of rocks, which do not have intensive gas-generation when beeng heated; salt deposits and clays. Basing on the results of calculations it has been shown that the dimentions of zones of substantial deformations in the case of the high-level radioactive wastes burial to not exceed several hundreds of meters. Conclusion is made that in the case of choosing the proper geotogicat structure for burial and ir the case of inclusion in the structure of the burial site a zone of sanitary alienation, it is possible to isolate wastes safely for all the period of preservation. Preliminary demands have been formulated to geological structures and underground burial sites. As main tasks for optimizatiop of burial sited are considered: determination of necessary types, number and reliability of barriers which ensure isolation of wastes; to make prognoses of the stressed and deformed state of a geological massif on the influence of thermal field; investigation in changes of chemical and physical properties of rocks under heat, radiative and chemical influence; estimation of possible diffusion of radioactivity in a mountin massif; development of a rational mining-thechnological schemes of the burual of wastes of different types. A row of tasks in the farmeworks of this probtem are sotved successfutty. Some resutts are given of the theoretical investigations in determination of zones of distructions of rocks because of heat-load [ru

Mathematical model quantifies multiple daylight exposure and burial events for rock surfaces using luminescence dating

International Nuclear Information System (INIS)

Freiesleben, Trine; Sohbati, Reza; Murray, Andrew; Jain, Mayank; Al Khasawneh, Sahar; Hvidt, Søren; Jakobsen, Bo

2015-01-01

Interest in the optically stimulated luminescence (OSL) dating of rock surfaces has increased significantly over the last few years, as the potential of the method has been explored. It has been realized that luminescence-depth profiles show qualitative evidence for multiple daylight exposure and burial events. To quantify both burial and exposure events a new mathematical model is developed by expanding the existing models of evolution of luminescence–depth profiles, to include repeated sequential events of burial and exposure to daylight. This new model is applied to an infrared stimulated luminescence-depth profile from a feldspar-rich granite cobble from an archaeological site near Aarhus, Denmark. This profile shows qualitative evidence for multiple daylight exposure and burial events; these are quantified using the model developed here. By determining the burial ages from the surface layer of the cobble and by fitting the new model to the luminescence profile, it is concluded that the cobble was well bleached before burial. This indicates that the OSL burial age is likely to be reliable. In addition, a recent known exposure event provides an approximate calibration for older daylight exposure events. This study confirms the suggestion that rock surfaces contain a record of exposure and burial history, and that these events can be quantified. The burial age of rock surfaces can thus be dated with confidence, based on a knowledge of their pre-burial light exposure; it may also be possible to determine the length of a fossil exposure, using a known natural light exposure as calibration. - Highlights: • Evidence for multiple exposure and burial events in the history of a single cobble. • OSL rock surface dating model improved to include multiple burial/exposure cycles. • Application of the new model quantifies burial and exposure events.

Alternatives to control subsidence at low-level radioactive waste burial sites

International Nuclear Information System (INIS)

Phillips, S.J.; Carlson, R.A.

1981-09-01

A substantial quantity of low-level radioactive and hazardous wastes has been interred in shallow land burial structures throughout the United States. Many of these structures (trenches, pits, and landfills) have experienced geotechnical subsidence problems and may require stabilization. Ground surface manifestations of subsidence include: large cracks, basins, and cave-ins. Subsidence is primarily caused by void filling, and physicochemical degradation and solubilization of buried wastes. These surface features represent a potential for increased contamination transport to the biosphere via water, air, biologic, and direct pathways. Engineering alternatives for the reduction of buried waste and matrix materials voids are identified and discussed. The advantages, disadvantages, and costs of each alternative are evaluated. Falling mass, pile driving and in situ incineration engineering alternatives were selected for further development

Shallow land burial handbook

International Nuclear Information System (INIS)

Stinton, L.H.

1983-01-01

The facility development phases (preliminary analysis, site selection, facility design and construction, facility operation, and facility closure/post-closure) are systematically integrated into a logical plan for developing near surface disposal plans. The Shallow Land Burial Handbook provides initial guidance and concepts for understanding the magnitude and the complexity of developing new low-level radioactive waste disposal facilities

Underwater Munitions Expert System to Predict Mobility and Burial

Science.gov (United States)

2017-11-14

for predicting the location and possible burial of underwater munitions is required to advise site managers as they plan...that region above the given UXO relative density, which is defined as the UXO density divided by the sand grain density, ( nominally 2650 g...0.0 + 2.5*dsed ; % nominal bed roughness if no burial % (Potentially in future version, ripple height

In situ grouting of low-level burial trenches with a cement-based grout

International Nuclear Information System (INIS)

Francis, C.W.; Spalding, B.P.

1991-01-01

A restoration technology being evaluated for use in the closure of one of the low-level radwaste burial grounds at Oak Ridge National Laboratory (ORNL) is trench stabilization using a cement-based grout. To demonstrate the applicability and effectiveness of this technology, two interconnecting trenches in Solid Waste Storage Area 6 (SWSA 6) were selected as candidates for in situ grouting with a particulate grout. The primary objective was to demonstrate the increased trench stability and decreased potential for leachate migration following in situ injection of a particulate grout into the waste trenches. Stability against trench subsidence is a critical issue. 7 refs., 3 figs., 5 tabs

Long term stability of yttria-stabilized zirconia waste forms. Stability for secular change of partitioned TRU waste composition by disintegration

International Nuclear Information System (INIS)

Kuramoto, Ken-ichi; Banba, Tsunetaka; Mitamura, Hisayoshi; Sakai, Etsuro; Uno, Masayoshi; Kinoshita, H.; Yamanaka, Shinsuke

1999-01-01

In this study, the stability of YSZ waste forms for secular change of partitioned TRU waste composition by disintegration, one of important terms in long-term stability, is the special concern. Designed amount of waste and YSZ powder were mixed and sintered. These TRU waste forms were submitted to tests of phase stability, chemical durability, mechanical property and compactness. The results were compared with those of another YSZ waste forms, non-radioactive Ce and/or Nd doped YSZ samples, and glass and Synroc waste forms. Experimental results show following: (1) Phase stability of (Np+Am)-, (Np+U)-, and (Np+U+Bi)-doped YSZ waste forms could be maintained of that of the initial Np+Am-doped YSZ waste form permanently even when the composition of partitioned TRU waste were changed by disintegration. (2) Secular change also accelerated volume increase of YSZ waste forms as well as alpha-decay damage. (3) Hv, E and K IC of (Np+U)- and (Np+U+Bi)-doped YSZ waste forms were independent of the secular change of the partitioned TRU waste composition by disintegration. (4) Mechanical properties of YSZ waste forms were more than those of a glass and Synroc waste forms. (5) Compactness of YSZ waste forms was good as waste forms for the partitioned TRU wastes. (J.P.N.)

Systematic evaluation of options to avoid generation of noncertifiable transuranic (TRU) waste at Los Alamos National Laboratory

International Nuclear Information System (INIS)

Boak, J.M.; Kosiewicz, S.T.; Triay, I.; Gruetzmacher, K.; Montoya, A.

1998-03-01

At present, >35% of the volume of newly generated transuranic (TRU) waste at Los Alamos National Laboratory is not certifiable for transport to the Waste Isolation Pilot Plant (WIPP). Noncertifiable waste would constitute 900--1,000 m 3 of the 2,600 m 3 of waste projected during the period of the Environmental Management (EM) Accelerated Cleanup: Focus on 2006 plan (DOE, 1997). Volume expansion of this waste to meet thermal limits would increase the shipped volume to ∼5,400 m 3 . This paper presents the results of efforts to define which TRU waste streams are noncertifiable at Los Alamos, and to prioritize site-specific options to reduce the volume of certifiable waste over the period of the EM Accelerated Cleanup Plan. A team of Los Alamos TRU waste generators and waste managers reviewed historic generation rates and thermal loads and current practices to estimate the projected volume and thermal load of TRU waste streams for Fiscal Years 1999--2006. These data defined four major problem TRU waste streams. Estimates were also made of the volume expansion that would be required to meet the permissible wattages for all waste. The four waste streams defined were: (1) 238 Pu-contaminated combustible waste from production of Radioactive Thermoelectric Generators (RTGs) with 238 Pu activity which exceeds allowable shipping limits by 10--100X. (2) 241 Am-contaminated cement waste from plutonium recovery processes (nitric and hydrochloric acid recovery) are estimated to exceed thermal limits by ∼3X. (3) 239 Pu-contaminated combustible waste, mainly organic waste materials contaminated with 239 Pu and 241 Am, is estimated to exceed thermal load requirements by a factor of ∼2X. (4) Oversized metal waste objects, (especially gloveboxes), cannot be shipped as is to WIPP because they will not fit in a standard waste box or drum

Thermal processing systems for TRU mixed waste

International Nuclear Information System (INIS)

Eddy, T.L.; Raivo, B.D.; Anderson, G.L.

1992-01-01

This paper presents preliminary ex situ thermal processing system concepts and related processing considerations for remediation of transuranic (TRU)-contaminated wastes (TRUW) buried at the Radioactive Waste Management Complex (RWMC) of the Idaho National Engineering Laboratory (INEL). Anticipated waste stream components and problems are considered. Thermal processing conditions required to obtain a high-integrity, low-leachability glass/ceramic final waste form are considered. Five practical thermal process system designs are compared. Thermal processing of mixed waste and soils with essentially no presorting and using incineration followed by high temperature melting is recommended. Applied research and development necessary for demonstration is also recommended

A Deformation Model of TRU Metal Dispersion Fuel Rod for HYPER

International Nuclear Information System (INIS)

Lee, Byoung Oon; Hwang, Woan; Park, Won S.

2002-01-01

Deformation analysis in fuel rod design is essential to assure adequate fuel performance and integrity under irradiation conditions. An in-reactor performance computer code for a dispersion fuel rod is being developed in the conceptual design stage of blanket fuel for HYPER. In this paper, a mechanistic deformation model was developed and the model was installed into the DIMAC program. The model was based on the elasto-plasticity theory and power-law creep theory. The preliminary deformation calculation results for (TRU-Zr)-Zr dispersion fuel predicted by DIMAC were compared with those of silicide dispersion fuel predicted by DIFAIR. It appeared that the deformation levels for (TRU-Zr)-Zr dispersion fuel were relatively higher than those of silicide fuel. Some experimental tests including in-pile and out-pile experiments are needed for verifying the predictive capability of the DIMAC code. An in-reactor performance analysis computer code for blanket fuel is being developed at the conceptual design stage of blanket fuel for HYPER. In this paper, a mechanistic deformation model was developed and the model was installed into the DIMAC program. The model was based on the elasto-plasticity theory and power-law creep theory. The preliminary deformation calculation results for (TRUZr)- Zr dispersion fuel predicted by DIMAC were compared with those of silicide dispersion fuel predicted by DIFAIR. It appears that the deformation by swelling within fuel meat is very large for both fuels, and the major deformation mechanism at cladding is creep. The swelling strain is almost constant within the fuel meat, and is assumed to be zero in the cladding made of HT9. It is estimated that the deformation levels for (TRU-Zr)-Zr dispersion fuel were relatively higher than those of silicide fuel, and the dispersion fuel performance may be limited by swelling. But the predicted volume change of the (TRU-Zr)-Zr dispersion fuel models is about 6.1% at 30 at.% burnup. The value of cladding

Review on technical issues influencing the performance of chemical barriers of TRU waste repository

International Nuclear Information System (INIS)

Fujita, Tomonari; Sugiyama, Daisuke; Tsukamoto, Masaki; Yokoyama, Hayaichi

1997-01-01

Studies of technical issues influencing the performance assessment of TRU waste disposal which is occurred from the nuclear fuel reprocessing were reviewed in related to the development of safety analysis method. Especially, the chemical containment was investigated as a key barrier to radionuclide migration. TRU waste including long-lived radionuclides need long-term performance assessment which could be assumed only by the chemical barrier. The description of technical issues concerned with the performance of TRU waste repository has been divided into the following categories: long-term degradation of cementitious materials as engineered barrier for radionuclide migration, effect of colloids, organic macromolecules and organic degradation products on chemical behavior of radionuclides, gas generation by corrosion of metallic wastes, and effects of microbial activity. Preliminary performance assessment indicated that important factors affecting performance of chemical barriers in near-field were the distribution coefficient and the solubility of radionuclides in near-field groundwater. Therefore, it was identified that key issues associated with performance of chemical barrier were evaluation of (a) the long-term change of distribution coefficient of cementitious material through the degradation under repository condition and (b) chemical speciation change of radionuclides such as increase of solubility by the presence of colloidal-size materials. (author)

Radionuclide dynamics and health implications for the New York nuclear service center's radioactive waste burial site

International Nuclear Information System (INIS)

Matuszek, J.M.; Strnisa, F.V.; Baxter, C.F.

1976-01-01

A commercial radioactive waste burial site has operated since 1963 at the Western New York Nuclear Service Center. Solid low-level radioactive wastes are buried in trenches excavated from a very fine-grained heterogeneous mixture of silt and clay (silty till) and are then covered with the excavated material. Despite many operational precautions, water levels in three burial trenches rose to within a few centimeters of the covering material by late 1973. Activity levels of HTO, 90 Sr, and 137 Cs in trench water and core samples were measured to obtain preliminary information on the degree of subsurface radionuclide migration from the burial trenches into the surrounding soil. Tritium concentrations measured in void-space water from vertical cores appeared to peak in the cover material 1.5 to 2m below the ground surface. Concentrations of 90 Sr and 137 Cs in the silty till were greatest near the surface of the cover material. Concentrations of HTO and 90 Sr, measured in a series of slant-hole core samples collected until the trench was intercepted, showed tritium migration to have progressed less than 0.3m, while 90 Sr migration appeared to be somewhat less. The preliminary data suggest that: (a) radionuclide migration from the burial trenches into the undisturbed silty till is slight; (b) radioactivity in the surface soil is not necessarily caused by migration of trench water; (c) groundwater movement is not massive; (d) rainwater infiltration, with settlement and compaction of buried wastes, is the most likely cause of rising trench water levels; and (e) surface contamination may occur from spills during burial operations, from trench digging, and from deposition of stack effluents from a nearby nuclear fuel reprocessing plant. By January 1975 the steadily rising water levels in three trenches were approximately 1m above the undisturbed soil from which the trenches were excavated, resulting in increased radioactivity levels in local streams draining the site. To

TRU Waste Sampling Program: Volume I. Waste characterization

International Nuclear Information System (INIS)

Clements, T.L. Jr.; Kudera, D.E.

1985-09-01

Volume I of the TRU Waste Sampling Program report presents the waste characterization information obtained from sampling and characterizing various aged transuranic waste retrieved from storage at the Idaho National Engineering Laboratory and the Los Alamos National Laboratory. The data contained in this report include the results of gas sampling and gas generation, radiographic examinations, waste visual examination results, and waste compliance with the Waste Isolation Pilot Plant-Waste Acceptance Criteria (WIPP-WAC). A separate report, Volume II, contains data from the gas generation studies

TruStore: Implementing a Trusted Store for Android

OpenAIRE

Yury, Zhauniarovich; Olga, Gadyatskaya; Bruno, Crispo

2013-01-01

In the Android ecosystem, the process of verifying the integrity of downloaded apps is left to the user. Different from other systems, e.g., Apple, App Store, Google does not provide any certified vetting process for the Android apps. This choice has a lot of advantages but it is also the open door to possible attacks as the recent one shown by Bluebox. To address this issue, we present how to enable the deployment of application certification service, we called TruStores, for the Android pla...

Impact of Cultivation and Subsequent Burial on Cydia pomonella (Lepidoptera: Tortricidae) and Conotrachelus nenuphar (Coleoptera: Curculionidae).

Science.gov (United States)

Baughman, William B; Nelson, Peter N; Grieshop, Matthew J

2015-06-01

We assessed the efficacy of cultivation as a potential management strategy for codling moth, Cydia pomonella L. (Lepidoptera: Tortricidae), and plum curculio, Conotrachelus nenuphar Herbst (Coleoptera: Curculionidae) in apple orchards. Cocooned codling moth pupae and thinning apples infested with plum curculio larvae were cultivated over in the field. Emergence, percent burial, damage to buried fruit, and depth of burial was recorded. In the laboratory, both insects were buried at variable depths in sand and potting soil and emergence was measured. A greater proportion of plum curculio larvae buried in infested fruit under laboratory conditions survived to adulthood compared with unburied infested fruit, down to 15 cm. No codling moth adults emerged from under 1 cm or more of sand. Buried codling moth larvae experienced drastically reduced survival to adulthood compared with unburied larvae. These results indicate that strip cultivation may negatively impact codling moth diapausing larvae and pupae on the ground, but not likely to negatively impact plum curculio in infested dropped apples. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America.

Computerized methodology for evaluating the long-range radiological impact of shallow-land burial

International Nuclear Information System (INIS)

Fields, D.E.; Little, C.A.; Emerson, C.J.

1981-01-01

A computerized methodology has been implemented to calculate the risk to local and intermediate-range (up to 80 km distant) populations resulting from water- and air-borne transport of radionuclides present in low-level wastes buried in shallow trenches such as those used at Oak Ridge. Our computer code, PRESTO (Prediction of Radiation Effects from Shallow Trench Operations), was developed under United States Environmental Protection Agency funding to evaluate possible health effects resulting from shallow burial operations. Sources of contamination include radionuclide releases from the trenches and from areas contaminated with operational spillage. The model is intended to predict radionuclide transport and the ensuing exposure and health impact to at-risk populations for a 1000-year period following cessation of burial ground operations. Several classes of submodels are used in PRESTO to represent scheduled event, unit system response, and risk evaluation processes. Examples of scheduled events are trench cap failure, stabilization of insoluble surface contaminant, the onset of farming or reclamation practices, and human intrusion. Unit system response submodels simulate processes such as infiltration of rainwater into the trench and erosion of soil overburden from the trench cover. System response submodels generate parameters used repeatedly in the 1000-year simulation loop

Organic Carbon Burial in Brazilian Mangrove Sediments (Invited)

Science.gov (United States)

Sanders, C.; Smoak, J. M.; Sanders, L.; Patchineelam, S.

2010-12-01

This study reviews the organic carbon (OC) burial rates in mangrove forests, margins and mud flats in geographically distinct areas of the Brazilian coastline. We exam the burial rates, taking into account the geomorphology of each region. Our initial results indicate that the Northeastern region of Brazil is sequestering significantly more OC than in the Southeastern areas, being that the mass sediment accumulation rates remained consistent within the forests as opposed to large variations found in the mudflats. The other pertinent factor was OC content, which differed substantially in respect to region. Given that the mangrove forests of the Southeastern regions of Brazil may be more susceptible to a rising sea level, as these areas are constricted by vast mountain ranges, this work attempts to put in perspective the possible impacts of climate change on mangrove ecosystems and OC burial along the Brazilian coastal ocean. We also compare our result to global averages.

Munition Burial by Local Scour and Sandwaves: large-scale laboratory experiments

Science.gov (United States)

Garcia, M. H.

2017-12-01

Our effort has been the direct observation and monitoring of the burial process of munitions induced by the combined action of waves, currents and pure oscillatory flows. The experimental conditions have made it possible to observe the burial process due to both local scour around model munitions as well as the passage of sandwaves. One experimental facility is the Large Oscillating Water Sediment Tunnel (LOWST) constructed with DURIP support. LOWST can reproduce field-like conditions near the sea bed. The second facility is a multipurpose wave-current flume which is 4 feet (1.20 m) deep, 6 feet (1.8 m) wide, and 161 feet (49.2 m) long. More than two hundred experiments were carried out in the wave-current flume. The main task completed within this effort has been the characterization of the burial process induced by local scour as well in the presence of dynamic sandwaves with superimposed ripples. It is found that the burial of a finite-length model munition (cylinder) is determined by local scour around the cylinder and by a more global process associated with the formation and evolution of sandwaves having superimposed ripples on them. Depending on the ratio of the amplitude of these features and the body's diameter (D), a model munition can progressively get partially or totally buried as such bedforms migrate. Analysis of the experimental data indicates that existing semi-empirical formulae for prediction of equilibrium-burial-depth, geometry of the scour hole around a cylinder, and time-scales developed for pipelines are not suitable for the case of a cylinder of finite length. Relative burial depth (Bd / D) is found to be mainly a function of two parameters. One is the Keulegan-Carpenter number, KC, and the Shields parameter, θ. Munition burial under either waves or combined flow, is influenced by two different processes. One is related to the local scour around the object, which takes place within the first few hundred minutes of flow action (i.e. short

Study of the External Neutron Source Effect on TRU Burning in a Sub-critical Reactor

Energy Technology Data Exchange (ETDEWEB)

Zafar, Zafar Iqbal; Kim, Myung Hyun [Kyung Hee University, Yongin (Korea, Republic of)

2015-05-15

One of the drawback points of nuclear power is the production of highly radioactive and long lasting waste isotopes during power production. Therefore, most important design requirement of future nuclear option should have a potential to burn selectively long-lived fission products (LLFP) and long-lived minor actinides (LLMA). However, there is no way to burn them selectively in the reactor core. Practical method of waste transmutation should rely on selective separation of them from spent nuclear fuel of power plants. Under the proliferation concern, direct separation of trans-uranic isotopes (TRU) from pyro-reprocessing plant became a feasible option in our country. Even though social political agreement is not matured as well as technical feasibility, current study is done based on basic assumptions; TRU and LLFP is separated from spent fuel of nuclear power plants. The remaining neutrons (among the external 3%) very few in number (less than 1% in any case) being very energetic (above three MeV or so) do cause much more fissions per neutron than their counterparts but, because of their overall low population they do not have any significant and decisive influence in the overall reactor performance. Currently, entire study is limited to the source neutron energy of 20 MeV only. In future, it is expected to get reasonably plausible fixed source dependent difference in the TRU burning by using tabulated data for the neutrons of higher energy (up to 250 MeV at least). Secondly, a clearer picture is expected if the TRU loading was increased from the current value of 133 kg to few metric tons, as is the case in most of the existing reactors.

Phosphorus recycling and burial in Baltic Sea sediments with contrasting redox conditions

DEFF Research Database (Denmark)

Mort, Haydon P; Slomp, Caroline P; Gustafson, Bo G

2010-01-01

. Most burial of P takes place as organic P. We find no evidence for significant authigenic Ca–P formation or biogenic Ca–P burial. The lack of major inorganic P burial sinks makes the Baltic Sea very sensitive to the feedback loop between increased hypoxia, enhanced regeneration of P and increased......In this study, redox-dependent phosphorus (P) recycling and burial at 6 sites in the Baltic Sea is investigated using a combination of porewater and sediment analyses and sediment age dating (210Pb and 137Cs). We focus on sites in the Kattegat, Danish Straits and Baltic Proper where present...... be accounted for in budgets and models for the Baltic Sea....

Management of transuranic wastes throughout the world

International Nuclear Information System (INIS)

Lakey, L.T.; Christensen, H.; De Jonghe, P.; Frejaville, G.; Lavie, J.M.; Thackrah, D.G.

1983-01-01

Transuranic (TRU) wastes are those radioactive wastes, except spent fuel and high-level wastes, that are contaminated with sufficient long-lived, alpha-emitting nuclides that the decay to innocuous levels in engineered storage structures or shallow-land burial sites cannot be used as a disposal method. This class of waste is produced principally during spent fuel reprocessing, recycle fuel fabrication, and weapons material production. At least ten countries are involved in operations producing this class of waste, which represents a small fraction of the alpha-emitting nuclides in the world's inventory and of the total volume of radioactive wastes produced in nuclear activities. No consensus has been reached on a numerical definition; definitions in use vary from >0.03 to >1000 nCi transuranium radionuclides per gram of waste (TRU/g). The definitions are presently used to separate wastes going to sea dumping or shallow-land burial from those requiring greater isolation. All countries emphasize plutonium recovery and volume reduction in their plans for treating TRU wastes. Incineration is the most prevalent treatment in use. When fixation is used, cement and bitumen are the preferred fixation media. All high-concentration TRU wastes are now being placed in interim storage. No TRU wastes are presently being disposed except the low-concentration wastes being dumped at sea by Belgium and the United Kingdom and those being injected into geologic strata by the United States (Oak Ridge National Laboratory) and the USSR. All countries prefer and are planning to use deep geologic repositories for final disposal of TRU wastes. According to present schedules, the Waste Isolation Pilot Plant (WIPP) facility in the United States, with a scheduled startup date of 1989, will be the first operating repository since the closure of the Federal Republic of Germany's Asse Salt Mine in 1977

LASL experimental engineered waste burial facility: design considerations and preliminary plan

International Nuclear Information System (INIS)

DePoorter, G.L.

1980-01-01

The LASL Experimental Engineered Waste Burial Facility is a part of the National Low-Level Waste Management Program on Shallow-Land Burial Technology. It is a test facility where basic information can be obtained on the processes that occur in shallow-land burial operations and where new concepts for shallow-land burial can be tested on an accelerated basis on an appropriate scale. The purpose of this paper is to present some of the factors considered in the design of the facility and to present a preliminary description of the experiments that are initially planned. This will be done by discussing waste management philosophies, the purposes of the facility in the context of the waste management philosophy for the facility, and the design considerations, and by describing the experiments initially planned for inclusion in the facility, and the facility site

Effect of soil erosion on the long-term stability of FUSRAP near-surface waste-burial sites

International Nuclear Information System (INIS)

Knight, M.J.

1983-04-01

Decontamination of FUSRAP sites could result in the generation of large volumes (in excess of 400,000 m 3 ) of low-activity radioactive wastes (primarily contaminated soil and building materials) requiring subsequent disposal. It is likely that near-surface burial will be seriously considered as an option for disposal of these materials. A number of factors - including soil erosion - could adversely affect the long-term stability of a near-surface waste-burial site. The majority of FUSRAP sites are located in the humid eastern United States, where the principal cause of erosion is the action of water. This report examines the effect of soil erosion by water on burial-site stability based on analysis of four hypothetical near-surface burial sites. The Universal Soil Loss Equation was employed to estimate average annual soil loss from burial sites and the 1000-year effects of soil loss on the soil barrier (burial trench cap) placed over low-activity wastes. Results suggest that the land use of the burial site and the slope gradient of the burial trench cap significantly affect the rate of soil erosion. The development of measures limiting the potential land use of a burial site (e.g., mixing large rocks into the burial trench cap) may be required to preserve the integrity of a burial trench for long periods of time

Burial trench dynamic compaction demonstration at a humid site

International Nuclear Information System (INIS)

Spalding, B.P.

1985-01-01

This task has the objective of determining the degree of consolidation which can be achieved by dynamic compaction of a closed burial trench within a cohesive soil formation. A seven-year-old burial trench in Solid Waste Storage Area (SWSA) 6 of Oak Ridge National Laboratory (ORNL) was selected for this demonstration. This 251 m 3 trench contained about 80 Ci of mixed radionuclides, mostly 90 Sr, in 25 m 3 of waste consisting of contaminated equipment, dry solids, and demolition debris. Prior to compaction, a total trench void space of 79 m 3 was measured by pumping the trench full of water with corrections for seepage. Additional pre-compaction characterization included trench cap bulk density (1.68 kg/L), trench cap permeability (3 x 10 -7 m/s), and subsurface waste/backfill hydraulic conductivity (>0.01 m/s). Compaction was achieved by repeatedly dropping a 4-ton steel-reinforced concrete cylinder from heights of 4 to 8 m using the whipline of a 70-ton crane. The average trench ground surface was depressed 0.79 m, with some sections over 2 m, yielding a surveyed volumetric depression which totaled to 64% of the measured trench void space. Trench cap (0 to 60 cm) bulk density and permeability were not affected by compaction indicating that the consolidation was largely subsurface. Neither surface nor airborne radioactive contamination were observed during repeated monitoring during the demonstration. Dynamic compaction was shown to be an excellent and inexpensive (i.e., about $20/m 2 ) method to collapse trench void space, thereby hastening subsidence and stabilizing the land surface. 15 refs., 10 figs., 3 tabs

Analysis of TRU waste for RCRA-listed elements

International Nuclear Information System (INIS)

Mahan, C.; Gerth, D.; Yoshida, T.

1996-01-01

Analytical methods for RCRA listed elements on Portland cement type waste have been employed using both microwave and open hot plate digestions with subsequent analysis by inductively coupled plasma atomic emission spectroscopy (ICP-AES), inductively coupled plasma mass spectrometry (ICP-AES), inductively coupled plasma mass spectrometry (ICP-MS), graphite furnace atomic absorption (GFAA) and cold vapor atomic absorption and fluorescence (CVAA/CVAFS). Four different digestion procedures were evaluated including an open hot plate nitric acid digestion, EPA SW-846 Method 3051, and 2 methods using modifications to Method 3051. The open hot plate and the modified Method 3051, which used aqua regia for dissolution, were the only methods which resulted in acceptable data quality for all 14 RCRA-listed elements. Results for the nitric acid open hot plate digestion were used to qualify the analytical methods for TRU waste characterization, and resulted in a 99% passing score. Direct chemical analysis of TRU waste is being developed at Los Alamos National Laboratory in an attempt to circumvent the problems associated with strong acid digestion methods. Technology development includes laser induced breakdown spectroscopy (LIBS), laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS), dc arc CID atomic emission spectroscopy (DC-AES), and glow discharge mass spectrometry (GDMS). Analytical methods using the Portland cement matrix are currently being developed for each of the listed techniques. Upon completion of the development stage, blind samples will be distributed to each of the technology developers for RCRA metals characterization

Mine burial in the seabed of high-turbidity area—Findings of a first experiment

Science.gov (United States)

Baeye, Matthias; Fettweis, Michael; Legrand, Sebastien; Dupont, Yves; Van Lancker, Vera

2012-07-01

The seabed of the North Sea is covered with ammunition dating back from World Wars I and II. With increasing human interference (e.g. fisheries, aggregate extraction, harbor related activities), it forms a threat to the safety at sea. In this study, test mines were deployed on a sandy seabed for 3 months to investigate mine burial processes as a function of hydrodynamic and meteorological conditions. The mine experiment was conducted in a shallow (9 m), macrotidal environment characterized by highly turbid waters (yearly and depth-averaged suspended particulate matter concentration of 100 mg l-1). Results showed some variability of the overall mine burial, which corresponded with scouring processes induced by a (sub-) tidal forcing mechanism. The main burial events however were linked to storm-related scouring processes, and subsequent mine roll into the resulting pit. Two storms affecting the mines during the 3-month experiment resulted in enduring increases in burial volume to 60% and 80%, respectively. More cyclic and ephemeral burial and exposure events appear to be linked to the local hydrodynamic regime. During slack tides, suspended sediment settles on the seabed, increasing the burial volume. In between slack tides, sediment is resuspended, decreasing the burial volume. The temporal pattern of this never reported burial mechanism, as measured optically, mimics the cyclicity of the suspended sediment concentration as recorded by ultrasonic signals at a nearby benthic observatory. Given the similarity in response signals at the two sites, we hypothesize that the formation of high-concentrated mud suspensions (HCMS) is a mechanism causing short-term burial and exposure of mines. This short-term burial and exposure increase the chance that mines are 'missed' during tracking surveys. Test mines contribute to our understanding of the settling and erosion of HCMS, and thus shed a light on generic sedimentary processes.

Current Program for the management of U.S. Department of Energy transuranic waste

International Nuclear Information System (INIS)

Harms, T.

1994-01-01

The existing inventory of TRU waste can be divided into tow distinct components: (1) retrievably stored TRU waste and (2) buried TRU waste. The distinction between open-quotes storedclose quotes and open-quotes buriedclose quotes TRU waste was established in 1970 when the Atomic Energy Commission (AEC) determined that TRU-contaminated waste, when disposed, should have more effective isolation from the environment than the confinement provided by burial in pits and trenches covered with soil. Buried TRU (and contaminated soils surrounding buried TRU) are the results of disposal operations carried out at DOE sites prior to the 1970 decision. The inventory of buried TRU is 190,600 m 3 . This waste is the responsibility of the Office of Environmental Restoration (EM-40). All TRU waste generated since 1970 has been placed in storage at six DOE sites. This storage was designed with a lifetime expected to be 20 years. The waste is stored in retrievable form for eventual shipment and disposal at a geologic repository. Currently, TRU waste is contained in a variety of packaging, including metal drums and wooden and metal boxes, and stored in earth-mounded berms, concrete culverts, or other facilities. At the end of 1991, there were approximately 64,000 m 3 of retrievably stored TRU waste. With the WIPP facility not becoming operational until the year 2000 or later, the DOE must effectively manage this waste in other manners. The issues regarding the management of TRU wastes is described

TRU composition changes and their influence on FBR core characteristics in the LWR-to-FBR transition period

International Nuclear Information System (INIS)

Maruyama, Shuhei; Ohki, Shigeo; Mizuno, Tomoyasu

2009-01-01

In the conceptual core and fuel design studies in Fast Reactor Cycle Technology Development Project (FaCT Project) in Japan, much interest has been taken in the fuel nuclide compositions for a transition period from light water reactor to fast breeder reactor (FBR). In this paper, the range of transuranic (TRU) nuclide composition to be provided to FBR is evaluated with extended recycling scenario calculations. The influence of TRU composition changes on FBR core characteristics are also discussed with explanations of major contributing factors. (author)

Time-temperature-burial significance of Devonian anthracite implies former great (approx.6.5 km) depth of burial of Catskill Mountains, New York

International Nuclear Information System (INIS)

Friedman, G.M.; Sanders, J.E.

1982-01-01

Specimens of coalified plant debris in Tully-correlative strata of the Gilboa Formation (uppermost Middle Devonian) within the eastern Catskill Mountains of New York State have been converted to anthracite having a vitrinite reflectance of 2.5%. This implies a level of organic metamorphism (LOM) of 16. The specimens are about 350 m.y. old; if 200 m.y. is taken as the duration of the time of exposure to the maximum geothermal temperature, then the LOM of 16 and other thermal indicators imply a maximum temperature of 190 0 C. Using a geothermal gradient of 26 0 C.km -1 (17 0 F.1,000 ft -1 ), a former depth of burial of 6.5 km is implied. Such former deep burial is not usually inferred for the Catskills, but it is consistent with the idea that the thick (about 6.4 km or 21,000 ft) Carboniferous strata of northeastern Pennsylvania formerly extended northeast far enough to bury the Catskills. The lack of metamorphism of the Paleozoic strata lying about 4.5 km beneath the Tully-correlative rocks and exposed in the adjacent Hudson Valley places low limits on the former geothermal gradient; this supports the concept of great depth of former burial of the Catskills. For example, 6.5 km of former burial and a geothermal gradient of 26 0 C.km -1 imply a temperature of 307 0 C for the base of the Paleozoic. By contrast, only 1 km of former burial requires a geothermal gradient of 170 0 C.km -1 , which would have subjected the base of the Paleozoic to a temperature of 955 0 GAMMA, which is far higher than the 600 to 650 0 C recently inferred for the Acadian-age metamorphism of the Taconic allochthon in southwestern Massachusetts and adjoining areas

Customary right to befitting burial: a jurisprudential appraisal of four ...

African Journals Online (AJOL)

These symbols reveal unique rights for the people's entitlement. Among the rights to which an African is entitled is the right to befitting burial/funerals. This right comes with it, certain duties and/or obligations. The aim of this paper is to deconstruct the elements of applicable burial customs with a view to demonstrating their ...

Overview of management programs for plutonium-contaminated solid waste in the U.S.A

International Nuclear Information System (INIS)

Ramsey, R.W. Jr.; Daly, G.H.

1975-01-01

Programs for transuranium-contaminated solid wastes (TRU) in the U.S.A. are emphasizing a reduction in waste generation and the development of appropriate treatments to reduce the volume of wastes requiring interim storage and final disposal. Research and Development is emphasizing the establishment of sufficient information on treatment, hazards and storage to adopt a standardized procedure for handling wastes during an interim retrievable period and for final disposal. Federal responsibility for TRU waste is being proposed except for minimum amounts acceptable for commercial burial

Burial container subsidence load stress calculations

International Nuclear Information System (INIS)

Veith, E.M.

1995-11-01

This document captures the supporting analyses conducted to determine if the LLCE (Long-Length Contaminated Equipment) burial containers are structurally adequate under different trench closure scenarios. The LLCE is equipment that was inside tank farm tanks

Comprehensive implementation plan for the DOE defense buried TRU- contaminated waste program

International Nuclear Information System (INIS)

Everette, S.E.; Detamore, J.A.; Raudenbush, M.H.; Thieme, R.E.

1988-02-01

In 1970, the US Atomic Energy Commission established a ''transuranic'' (TRU) waste classification. Waste disposed of prior to the decision to retrievably store the waste and which may contain TRU contamination is referred to as ''buried transuranic-contaminated waste'' (BTW). The DOE reference plan for BTW, stated in the Defense Waste Management Plan, is to monitor it, to take such remedial actions as may be necessary, and to re-evaluate its safety as necessary or in about 10-year periods. Responsibility for management of radioactive waste and byproducts generated by DOE belongs to the Secretary of Energy. Regulatory control for these sites containing mixed waste is exercised by both DOE (radionuclides) and EPA (hazardous constituents). Each DOE Operations Office is responsible for developing and implementing plans for long-term management of its radioactive and hazardous waste sites. This comprehensive plan includes site-by-site long-range plans, site characteristics, site costs, and schedules at each site. 13 figs., 15 tabs

Resurrection imageries: A study of the motives for extravagant burial rituals in ancient Egypt

Directory of Open Access Journals (Sweden)

Jock M. Agai

2015-03-01

Full Text Available Unlike in the New Testament whereby faith in Christ can resurrect the dead, the ancient Egyptians believed that the bereaved created the resurrection of their deceased through burial rituals and by encouraging the living to serve their kings. They thought that faith alone in god or the gods was not enough to resurrect the dead, thus they seemingly superimposed resurrection alongside burials. Using the various forms of Egyptian burial rituals and evaluated from the perspective of the Christian concept of resurrection, this researcher attempts to search for the motives behind specific Egyptian burial rituals. The researcher proposes that the activities of the bereaved or of the living over the dead were paramount in resurrecting the dead in ancient Egypt. The purpose of this research is, firstly, to explain how the Egyptian burial rituals influenced their thoughts on resurrection and, secondly, to show that the Egyptian god(s might have depended on the living to raise the dead.Intradisciplinary and/or interdisciplinary implications: The ancient Egyptians lived their lives mainly to satisfy the interests of the dead, hence their extensive burial rituals. Whilst they believed in the power of the gods to raise the dead, there seemed to be another motive behind their burial practices which suggested that the living may have had more power to raise the dead. The power was realised in the activities of the living in the form of burials, tomb designs, mummification, food offering, and in remembering the dead. This research explains that these burial activities were relevant in resurrecting the dead without which the gods alone were not able to do that.

Development of crystalline ceramic for immobilization of TRU wastes in V.G. Khlopin Radium Institute

International Nuclear Information System (INIS)

Burakov, B.E.; Anderson, E.B.

1999-01-01

This paper discusses the Radium Institute's experience in the synthesis of crystalline ceramics based on two groups of actinide host-phases: 1) Zircon/zirconia-(Zn, Ac)SiO 4 /(Zr, Ac)O 2 , where Ac=Pu, Np, Am, Cm; 2) Garnet/perovskite-(Y, Gd, Ac) 3 (Al, Ga, Ac,..) 5 O 12 /(Y, Gd, Ac)(Al, Ga)O 3 . The zircon/zirconia ceramic was suggested as an universal waste form for the immobilization of TRU as well as weapon-grade Pu. Because the position of the Russian Ministry of Atomic Energy (Minatom) does not consider weapons Pu as a waste', the Radium Institute proposed the use of the same ceramic (mainly monophase zirconia ) as a Pu-fuel. The garnet/perovskite ceramic was suggested for the immobilization of military TRU wastes of complex chemical composition. The advantage of this ceramic is that Garnet and Perovskite host-phases can incorporate in their lattices not only actinides, but also other elements including neutron absorbers in a broad range of concentration and in different valence state. Sample of zircon/zirconia ceramic were prepared by hot uniaxial pressing (at temperature T=1300, 1400, 1500degC and pressure P=25 MPa) and sintering (at T=1450, 1490, 1500, 1600degC) methods using different types of initial precursor. Samples of garnet/perovskite ceramic were synthesized by melting method at T=2000degC. Ce, U, Gd were used as TRU stimulants for both types of ceramic. One sample of zircon/zirconia ceramic was doped with 10 wt.% of Pu 239 . Physico-chemical features of these ceramics are described. In conclusion we propose that the pressureless technology based on sintering or melting methods be used for the synthesis of ceramics for the immobilization of all types of TRU wastes. (author)

A controlled monitoring study of simulated clandestine graves using 3D ground penetrating radar

CSIR Research Space (South Africa)

van Schoor, Michael

2017-06-01

Full Text Available A controlled three-dimensional ground penetrating radar monitoring study over simulated clandestine graves was conducted near Pretoria, South Africa, in which the detectability of graves as a function of post-burial interval was assessed...

Late Sarmatian Elite Military Burial From the Southern Urals

Directory of Open Access Journals (Sweden)

Krivosheev Mikhail Vasilyevich

2015-12-01

Full Text Available The article is devoted to the burial of a warrior of Late Sarmatian time from the Southern Urals. The complex from mound no. 4 of the burial mound Taksai I is distinguished by large size of barrow and grave. The reconstructed height of the mound was less than 2 meters. The depth of the burial pit was more than 3 meters. For Late Sarmatian culture such dimensions of sepulchral structures are unique. Under the mound the ritual platform from mainland soil was discovered. The found inventory of a warrior-rider included: horse bridle, a set of bladed weapons consisting of a long sword, dagger and knife, as well as a small bronze cauldron. Analysis of inventory allows us to date this burial to the second half of the 3rd century A.D. This burial belongs to an elite funerary complexes of Late Sarmatian culture and is a burial of professional warriors. This social stratum was formed in Late Sarmatian society at the end of the 2nd - first half of the 3rd century A.D. Most of these graves are dating back to the first half of the 3rd century A.D and were found in the Low Don and in the Volga region. The situation in these regions changed in that period due to the invasion of the tribes of the North-Caucasian origin. Their occurrence is associated with the destruction of the Tanais in the Lower Don region and the spread of graves in the T-shaped catacombs in the steppe monuments. The tradition of burying warriors-horsemen of high social status almost disappears in the Volga-Don steppes after the middle of 3rd century A.D. In the Southern Urals where these processes had an indirect influence, the existence of traditional hierarchies of Late Sarmatian society could continue until the end of the 3rd century A.D. Among the parts of a horse bridle the researchers discovered bronze B-shape buckle. These buckles are widely distributed in the 4th-5th centuries A.D. in the basin of the Kama river and the Danube river. The found buckle is the earliest currently known

Mathematical model quantifies multiple daylight exposure and burial events for rock surfaces using luminescence dating

DEFF Research Database (Denmark)

Freiesleben, Trine Holm; Sohbati, Reza; Murray, Andrew

2015-01-01

Interest in the optically stimulated luminescence (OSL) dating of rock surfaces has increased significantly over the last few years, as the potential of the method has been explored. It has been realized that luminescence-depth profiles show qualitative evidence for multiple daylight exposure...... and burial events. To quantify both burial and exposure events a new mathematical model is developed by expanding the existing models of evolution of luminescenceedepth profiles, to include repeated sequential events of burial and exposure to daylight. This new model is applied to an infrared stimulated...... events. This study confirms the suggestion that rock surfaces contain a record of exposure and burial history, and that these events can be quantified. The burial age of rock surfaces can thus be dated with confidence, based on a knowledge of their pre-burial light exposure; it may also be possible...

Report on waste burial charges. Escalation of decommissioning waste disposal costs at low-level waste burial facilities, Revision 4

International Nuclear Information System (INIS)

1994-06-01

One of the requirements placed upon nuclear power reactor licensees by the U.S. Nuclear Regulatory Commission (NRC) is for the licensees to periodically adjust the estimate of the cost of decommissioning their plants, in dollars of the current year, as part of the process to provide reasonable assurance that adequate funds for decommissioning will be available when needed. This report, which is scheduled to be revised periodically, contains the development of a formula for escalating decommissioning cost estimates that is acceptable to the NRC. The sources of information to be used in the escalation formula are identified, and the values developed for the escalation of radioactive waste burial costs, by site and by year, are given. The licensees may use the formula, the coefficients, and the burial escalation factors from this report in their escalation analyses, or they may use an escalation rate at least equal to the escalation approach presented herein. This fourth revision of NUREG-1307 contains revised spreadsheet results for the disposal costs for the reference PWR and the reference BWR and the ratios of disposal costs at the Washington, Nevada, and South Carolina sites for the years 1986, 1988, 1991 and 1993, superseding the values given in the May 1993 issue of this report. Burial cost surcharges mandated by the Low-Level Radioactive Waste Policy Amendments Act of 1985 (LLRWPAA) have been incorporated into the revised ratio tables for those years. In addition, spreadsheet results for the disposal costs for the reference reactors and ratios of disposal costs at the two remaining burial sites in Washington and South Carolina for the year 1994 are provided. These latter results do not include any LLRWPAA surcharges, since those provisions of the Act expired at the end of 1992. An example calculation for escalated disposal cost is presented, demonstrating the use of the data contained in this report

Influence of Anchoring on Burial Depth of Submarine Pipelines.

Science.gov (United States)

Zhuang, Yuan; Li, Yang; Su, Wei

2016-01-01

Since the beginning of the twenty-first century, there has been widespread construction of submarine oil-gas transmission pipelines due to an increase in offshore oil exploration. Vessel anchoring operations are causing more damage to submarine pipelines due to shipping transportation also increasing. Therefore, it is essential that the influence of anchoring on the required burial depth of submarine pipelines is determined. In this paper, mathematical models for ordinary anchoring and emergency anchoring have been established to derive an anchor impact energy equation for each condition. The required effective burial depth for submarine pipelines has then been calculated via an energy absorption equation for the protection layer covering the submarine pipelines. Finally, the results of the model calculation have been verified by accident case analysis, and the impact of the anchoring height, anchoring water depth and the anchor weight on the required burial depth of submarine pipelines has been further analyzed.

Soil Burial of Polylactic Acid/Paddy Straw Powder Biocomposite

Directory of Open Access Journals (Sweden)

Noorulnajwa Diyana Yaacob

2015-12-01

Full Text Available The objective of this work was to study the biodegradability of polylactic acid (PLA/paddy straw powder (PSP biocomposites. Environmental degradation was evaluated by composting the biocomposite samples into the soil. Different techniques, including mechanical tests and scanning electron microscopy (SEM, were used to obtain a view of the degradation that occurred during the soil burial of the biocomposites. Results of the mechanical tests showed that an increasing content of PSP in the biocomposites decreased the tensile strength and elongation at break (EB, while it increased the modulus of elasticity after six months of exposure. Scanning electron microscopy on the surface after soil burial showed that the filler was poorly wetted by the matrix. This explains the reduction in tensile strength and the elongation at break after soil burial. Differential scanning calorimetry results indicated that the crystallinity of the biocomposites increased with longer composting periods.

RCRA Closure Plan for the Bear Creek Burial Grounds B Area and Walk-In Pits at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1993-04-01

In June 1987, the RCRA Closure/Postclosure Plan for the Bear Creek Burial Grounds (BCBG) was submitted to the Tennessee Department of Environment and Conservation (TDEC) for review and approval. TDEC modified and issued the plan approved on September 30, 1987. Y/TS-395 was initially intended to apply to A Area, C-West, B Area, and the Walk-In Pits of BCBG. However, a concept was developed to include the B Area (non-RCRA regulated) in the Walk-In Pits so that both areas would be closed under one cap. This approach included a tremendous amount of site preparation with an underlying stabilization base of 16 ft of sand for blast protection. In January 1993, the Closure Plan was revised to include inspection and maintenance criteria and to reflect that future monitoring and remediation would be conducted as part of the ongoing Comprehensive Environmental Response, Compensation, and Liability Act activities at the Oak Ridge Y-12 Plant. This Closure Plan revision is intended to reflect the placement of the Kerr Hollow Quarry debris at the Walk-In Pits, revise the closure dates, and acknowledge that the disposition of a monitoring well within the closure site cannot be verified

Introduction: Life Space and Burial Space in the Post-Apartheid City ...

African Journals Online (AJOL)

Landscapes of the dead are always, simultaneously, landscapes of the living. It is this coterminousness of life and death that gives the burial site its salience and emotional power. Different societies, at different times, renegotiate the relationship between what anthropologists call 'life space\\' and 'burial space\\', depending on ...

Advanced conceptual design report solid waste retrieval facility, phase I, project W-113

International Nuclear Information System (INIS)

Smith, K.E.

1994-01-01

Project W-113 will provide the equipment and facilities necessary to retrieve suspect transuranic (TRU) waste from Trench 04 of the 218W-4C burial ground. As part of the retrieval process, waste drums will be assayed, overpacked, vented, head-gas sampled, and x-rayed prior to shipment to the Phase V storage facility in preparation for receipt at the Waste Receiving and Processing Facility (WRAP). Advanced Conceptual Design (ACD) studies focused on project items warranting further definition prior to Title I design and areas where the potential for cost savings existed. This ACD Report documents the studies performed during FY93 to optimize the equipment and facilities provided in relation to other SWOC facilities and to provide additional design information for Definitive Design

Status of microwave process development for RH-TRU [remote-handled transuranic] wastes at Oak Ridge National Laboratory

International Nuclear Information System (INIS)

White, T.L.; Youngblood, E.L.; Berry, J.B.; Mattus, A.J.

1990-01-01

The Oak Ridge National Laboratory (ORNL) Waste Handling and Packaging Plant is developing a microwave process to reduce and solidify remote-handled transuranic (RH-TRU) liquids and sludges presently stored in large tanks at ORNL. Testing has recently begun on an in-drum microwave process using nonradioactive RH-TRU surrogates. The microwave process development effort has focused on an in-drum process to dry the RH-TRU liquids and sludges in the final storage container and then melt the salt residues to form a solid monolith. A 1/3-scale proprietary microwave applicator was designed, fabricated, and tested to demonstrate the essential features of the microwave design and to provide input into the design of the full-scale applicator. The microwave fields are uniform in one dimension to reduce the formation of hot spots on the microwaved wasteform. The final wasteform meets the waste acceptance criteria for the Waste Isolation Pilot Plant, a federal repository for defense transuranic wastes near Carlsbad, New Mexico. 7 refs., 1 fig., 1 tab

Report on waste burial charges: Escalation of decommissioning waste disposal costs at low-level waste burial facilities

International Nuclear Information System (INIS)

1988-07-01

One of the requirements placed upon nuclear power reactor licensees by the US Nuclear Regulatory Commission (NRC) is for the licensees to periodically adjust the estimate of the cost of decommissioning their plant, in dollars of the current year, as part of the process to provide reasonable assurance that adequate funds for decommissioning will be available when needed. This report, which is scheduled to be revised annually, contains the development of a formula for escalating decommissioning cost estimates that is acceptable to the NRC, and contains values for the escalation of radioactive waste burial costs, by site and by year. The licensees may use the formula, the coefficients, and the burial escalation factors from this report in their escalation analysis, or may use an escalation rate at least equal to the escalation approach presented herein. 4 refs., 2 tabs

Helical-Tip Needle for Transthoracic Percutaneous Image-Guided Biopsy of Lung Tumors: Results of a Pilot Prospective Comparative Study with a Standard Tru-Cut Needle

Energy Technology Data Exchange (ETDEWEB)

Veltri, Andrea, E-mail: andrea.veltri@unito.it; Busso, Marco; Sardo, Diego; Angelino, Valeria; Priola, Adriano M. [University of Torino, Department of Radiology, San Luigi Gonzaga Hospital (Italy); Novello, Silvia [University of Torino, Department of Oncology, San Luigi Gonzaga Hospital (Italy); Barba, Matteo [University of Torino, Department of Radiology, San Luigi Gonzaga Hospital (Italy); Gatti, Gaia; Righi, Luisella [University of Torino, Department of Pathology, San Luigi Gonzaga Hospital (Italy)

2017-06-15

PurposeTo prospectively evaluate feasibility and diagnostic performance of the 14-gauge helical-tip (Spirotome™, Cook{sup ®} Medical, Bloomington, USA) needle in transthoracic needle biopsy (TTNB) of lung lesions, compared to a conventional 18-gauge Tru-Cut needle.Materials and MethodsStudy was institutional review board approved, with informed consent obtained. Data from synchronous Spirotome and Tru-Cut image-guided TTNB of 20 consecutive patients with malignant peripheral lung tumors larger than 3 cm were enrolled for pathologic characterization and mutational analysis. Samples obtained with Spirotome and Tru-Cut needle were compared for fragmentation, length, weight, morphologic and immunohistochemistry typifying, tumor cellularity (TC) and DNA concentration.ResultsThe technical success rate for TTNB with Spirotome was 100%, and no major complications occurred. Less fragmentation (mean 2 vs. 3 fragments, P = .418), greater weight (mean 13 vs. 8.5 mg, P = .027) and lower length (mean 10.2 vs. 12.6 mm, P = .174) were observed with Spirotome compared to Tru-Cut needle. Accuracy of Spirotome and Tru-Cut needle in defining cancer histotype was similar (90%). Absolute and relative TC (mean 42 vs. 38, 124 vs. 108/10HPF), and DNA concentration (mean 49.6 vs. 39.0 ng/μl) were higher with Spirotome compared to Tru-Cut needle, with no statistical significance (P = .787 and P = .140, respectively).Conclusions Percutaneous 14-gauge Spirotome TTNB of selected lesions is feasible and accurate. It provides adequate samples for diagnosis, comparable to 18-gauge Tru-Cut needle, with a higher amount of tumor tissue (weight, TC, DNA concentration) even in shorter samples.

Phosphorus burial in the ocean over glacial-interglacial time scales

Directory of Open Access Journals (Sweden)

F. Tamburini

2009-04-01

Full Text Available The role of nutrients, such as phosphorus (P, and their impact on primary productivity and the fluctuations in atmospheric CO₂ over glacial-interglacial periods are intensely debated. Suggestions as to the importance of P evolved from an earlier proposal that P actively participated in changing productivity rates and therefore climate change, to most recent ones that changes in the glacial ocean inventory of phosphorus were important but not influential if compared to other macronutrients, such as nitrate. Using new data coming from a selection of ODP sites, we analyzed the distribution of oceanic P sedimentary phases and calculate reactive P burial fluxes, and we show how P burial fluxes changed over the last glacial-interglacial period at these sites. Concentrations of reactive P are generally lower during glacial times, while mass accumulation rates (MAR of reactive P show higher variability. If we extrapolate for the analyzed sites, we may assume that in general glacial burial fluxes of reactive P are lower than those during interglacial periods by about 8%, because the lack of burial of reactive P on the glacial shelf reduced in size, was apparently not compensated by burial in other regions of the ocean. Using the calculated changes in P burial, we evaluate their possible impact on the phosphate inventory in the world oceans. Using a simple mathematical approach, we find that these changes alone could have increased the phosphate inventory of glacial ocean waters by 17–40% compared to interglacial stages. Variations in the distribution of sedimentary P phases at the investigated sites seem to indicate that at the onset of interglacial stages, shallower sites experienced an increase in reactive P concentrations, which seems to point to P-richer waters at glacial terminations. All these findings would support the Shelf-Nutrient Hypothesis, which assumes that during glacial low stands nutrients are transferred from shallow sites

Changes in CaCO3 Burial Trump the Biological Pump

Science.gov (United States)

Toggweiler, J.; Dunne, J. P.

2008-12-01

The dramatic increases in atmospheric CO2 at the ends of ice ages are usually attributed to a one-two punch coming from the ocean. First, a weakened biological pump vents organically cycled CO2 from the deep ocean via changes in the ventilation of the deep ocean around Antarctica. The initial CO2 increase is then augmented by an enhancement of CaCO3 burial due to a process called CaCO3 compensation (after Broecker, W. S and T.-H. Peng, Global Biogeochem. Cycles, 1, 15-29, 1987). Here, we argue that the importance of the biological pump has been exaggerated. The main effect comes from circulation-induced changes in the burial of CaCO3. As shown in a recent paper by Andreas Schmittner and co-authors (Schmittner, A., E. Brook and J. Ahn, Impact of the ocean's overturning circulation on atmospheric CO2, in Ocean Circulation: Mechanisms and Impacts, Geophys. Monogr. 173, A. Schmittner, J. Chiang, and S. Hemming, eds., pp. 209-246, AGU, 2007) changes in the ventilation of the deep ocean around Antarctica gave rise to 20-30 ppm increases in atmospheric CO2 every 5,000-7,000 years during isotope stages 3 and 4 (30,000 to 70,000 years ago). None of these venting events gave rise to a compensation response. Meanwhile, Jaccard et al. (Science, 308, 1003-1006, 2005) show that all the big CO2 increases during terminations through stage 11 were accompanied by huge increases in CaCO3 burial. This suggests that the enhanced burial of CaCO3 is obligatory rather than compensatory with respect to the dramatic CO2 increases. Broecker and Peng's compensation idea is based on an assumption that the rain of CaCO3 to the sea floor is the same everywhere. More specifically, it assumes that there is no spatial correlation between the production of CaCO3 at the surface and the burial on the sea floor. We find instead that the production and burial of CaCO3 tend to be co-located in regional "hot spots" and that burial in the hot spots balances the input of Ca++ and HCO3- ions in rivers. The

Influence of Anchoring on Burial Depth of Submarine Pipelines.

Directory of Open Access Journals (Sweden)

Yuan Zhuang

Full Text Available Since the beginning of the twenty-first century, there has been widespread construction of submarine oil-gas transmission pipelines due to an increase in offshore oil exploration. Vessel anchoring operations are causing more damage to submarine pipelines due to shipping transportation also increasing. Therefore, it is essential that the influence of anchoring on the required burial depth of submarine pipelines is determined. In this paper, mathematical models for ordinary anchoring and emergency anchoring have been established to derive an anchor impact energy equation for each condition. The required effective burial depth for submarine pipelines has then been calculated via an energy absorption equation for the protection layer covering the submarine pipelines. Finally, the results of the model calculation have been verified by accident case analysis, and the impact of the anchoring height, anchoring water depth and the anchor weight on the required burial depth of submarine pipelines has been further analyzed.

Parametric Criticality Safety Calculations for Arrays of TRU Waste Containers

Energy Technology Data Exchange (ETDEWEB)

Gough, Sean T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-10-26

The Nuclear Criticality Safety Division (NCSD) has performed criticality safety calculations for finite and infinite arrays of transuranic (TRU) waste containers. The results of these analyses may be applied in any technical area onsite (e.g., TA-54, TA-55, etc.), as long as the assumptions herein are met. These calculations are designed to update the existing reference calculations for waste arrays documented in Reference 1, in order to meet current guidance on calculational methodology.

Alternatives to the burial of low-level radioactive waste

International Nuclear Information System (INIS)

Price, J. Mark

2007-01-01

Available in abstract form only. Full text of publication follows: The approach for management of LLRW in different countries has evolved differently due to many factors such as culture and public sentiment, systems of government, public policy, and geography. There are also various methods to disposition LLRW including but not limited to: - Long term statutes and unconditional or conditional release of material, - Direct Burial, - Treatment (Processing) → Burial, - Treatment → Unconditional Release, - Recycle for Unconditional Release or Reuse Within Any Industry, - Controlled Recycle within Nuclear Industry. (author)

Mirrors in the Burial Rites of Saryarka Population in the Golden Horde Period

Directory of Open Access Journals (Sweden)

Khasenova Bakhyt M.

2017-12-01

Full Text Available The authors analyze the mirrors which were originally discovered in ancient Turkic burials, but became widely spread as late as in the Golden Horde period, which was largely accounted for by the intensification of contacts due to the establishment of the Mongol Empire. High-quality Chinese mirrors and their local imitations have been discovered across the entire vast territory in which the steppe peoples established new state formations. The authors support the opinion advanced by many researchers, according to which the mirrors represent ritual items. There is evidence of the fact that in the ancient Turkic period mirrors were characteristic of female burials. This information is partially confirmed for the developed medieval period as well, for paleoanthropological characteristics are not always available. The authors provide information on the conditions in which mirrors have been discovered in the burials of the historical period in question. The article features the first description of individual mirrors discovered in the burials of the steppe area of Kazakhstan. Of considerable interest is the discovery of one of the mirrors underneath a grave in a female burial conducted in accordance with the Muslim funerary rite. The authors attempt to identify the role of individual items in the burial rite of the medieval period, in this case mirrors, as a marker of gender identity.

Funeral dress and textiles in 17th and 19th century burials in Ostrobothnia, Finland

NARCIS (Netherlands)

Lipkin, S.; Vajanto, K.; Kallio-Seppä, T.; Kuokkanen, T.; Niinimäki, S.; Väre, T.; van Bommel, M.; Grömer, K.; Pritchard, F.

2015-01-01

The 17th-19th-century burial materials from northern Ostrobothnia are studied in order to consider the value, origin and meaning of textiles especially in child burials. The focus is on the preservation, quality and dyes of burial textiles unearthed at the yard of Oulu Cathedral as well as the

Position paper on flammability concerns associated with TRU waste destined for WIPP

International Nuclear Information System (INIS)

1991-04-01

The Waste Isolation Pilot Plant (WIPP), in southeastern New Mexico,is an underground repository, designed for the safe geologic disposal of transuranic (TRU) wastes generated from defense-related activities of the US Department of Energy (DOE). The WIPP storage rooms are mined in a bedded salt (halite) formation, and are located 2150 feet below the surface. After the disposal of waste in the storage rooms, closure of the repository is expected to occur by creep (plastic flow) of the salt formation, with the waste being permanently isolated from the surrounding environment. This paper has evaluated the issue of flammability concerns associated with TRU waste to be shipped to WIPP, including a review of possible scenarios that can potentially contribute to the flammability. The paper discusses existing regulations that address potential flammability concerns, presents an analysis of previous flammability-related incidents at DOE sites with respect to the current regulations, and finally, examines the degree of assurance these regulations provide in safeguarding against flammability concerns during transportation and waste handling. 50 refs., 7 figs., 7 tabs

Burial history of two potential clay host formations in Belgium

International Nuclear Information System (INIS)

Mertens, J.; Wouters, L.; Van Marcke, Ph.

2004-01-01

When dealing with long term stability of repository host rocks, it is important to consider and learn from all past geological events since the deposition of the formations. The burial history of the Boom Clay and Ypresian Clays, both considered as potential host rocks in Belgium, illustrates that the North Belgian region was tectonically relatively stable since deposition. In Northern Belgium, where both formations are located at a few hundreds meters of depth, tectonic movements were relatively small and no significant uplifts took place. The burial history of the Boom Clay in Mol, where the HADES underground research facility is located illustrates this. On the poster, the burial history for both formations is presented at two locations each: one location in the outcrop region and one research site location, where the formation is currently buried under a few 100 metres of sediment. (authors)

Determination of 99Tc in fresh water using TRU resin by ICP-MS.

Science.gov (United States)

Guérin, Nicolas; Riopel, Remi; Kramer-Tremblay, Sheila; de Silva, Nimal; Cornett, Jack; Dai, Xiongxin

2017-10-02

Technetium-99 ( 99 Tc) determination at trace level by inductively coupled plasma mass spectrometry (ICP-MS) is challenging because there is no readily available appropriate Tc isotopic tracer. A new method using Re as a recovery tracer to determine 99 Tc in fresh water samples, which does not require any evaporation step, was developed. Tc(VII) and Re(VII) were pre-concentrated on a small anion exchange resin (AER) cartridge from one litre of water sample. They were then efficiently eluted from the AER using a potassium permanganate (KMnO 4 ) solution. After the reduction of KMnO 4 in 2 M sulfuric acid solution, the sample was passed through a small TRU resin cartridge. Tc(VII) and Re(VII) retained on the TRU resin were eluted using near boiling water, which can be directly used for the ICP-MS measurement. The results for method optimisation, validation and application were reported. Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.

High integrity container evaluation for solid waste disposal burial containers

International Nuclear Information System (INIS)

Josephson, W.S.

1996-01-01

In order to provide radioactive waste disposal practices with the greatest measure of public protection, Solid Waste Disposal (SWD) adopted the Nuclear Regulatory Commission (NRC) requirement to stabilize high specific activity radioactive waste prior to disposal. Under NRC guidelines, stability may be provided by several mechanisms, one of which is by placing the waste in a high integrity container (HIC). During the implementation process, SWD found that commercially-available HICs could not accommodate the varied nature of weapons complex waste, and in response developed a number of disposal containers to function as HICs. This document summarizes the evaluation of various containers that can be used for the disposal of Category 3 waste in the Low Level Burial Grounds. These containers include the VECTRA reinforced concrete HIC, reinforced concrete culvert, and the reinforced concrete vault. This evaluation provides justification for the use of these containers and identifies the conditions for use of each

The treatment and conditioning of transuranelement bearing wastes in the Federal Republic of Germany

International Nuclear Information System (INIS)

Krause, H.

1986-01-01

Transuranelement bearing wastes (TRU wastes) differ from other radioactive wastes (with the exception of high level wastes from reprocessing) primarily by the longevity and high radiotoxity of many of their radionuclides. The volumes and total TRU content of these wastes are still quite small. Due to the present absence of a repository for radioactive wastes in the FRG, no definitions of TRU wastes and no acceptance criteria for these wastes have been fixed so far. Anyway, as only waste disposal into deep geological formations is envisaged for the time being, the limits for the TRU content do not need to be as low as in countries practicing shallow land burial. During the experimental disposal in the Asse salt mine, wastes with a TRU-content <5μCi/g were considered as non-TRU waste. There is some probability that in the future a similar value may be fixed. The present practice in TRU waste management is primarily determined by this situation. However, this system is neither ideal from a fundamental point of view nor in the long range; and, therefore, research and development work is going on for the development of an advanced TRU waste management system which should meet the requirements of an industrial scale fast breeder fuel cycle, and also improve the acceptance of such a program by the public. (Auth.)

Application of insoluble tannin to recovery of uranium, TRU and heavy metals elements form radioactive liquid waste

International Nuclear Information System (INIS)

Hamaguchi, Kazuhiko; Shirato, Wataru; Nakamura, Yasuo; Matsumura, Tatsuro; Takeshita, Kenji; Nakano, Yoshio

1999-01-01

Mitsubishi Nuclear Fuel Co., Ltd. (MNF) has developed a new adsorbent, TANNIX (tread mark), for the recovery of uranium, TRU and heavy metal elements in the liquid waste, in which TANNIX derived from a natural tannin polymer. TANNIX has same advantages that handling is easier than that of standard IX-resin, and that the volume of secondary waste is reduced by burning the used TANNIX. We have replaced its radioactive liquid waste treatment system from the conventional co-precipitation process to adsorption process by using TANNIX. TANNIX was founded to be more effective for the recovery of Pu, TRU, and hexavalent chromium Cr-(VI) as well as Uranium. (author)

Effects of sand burial on the survival and growth of two shrubs dominant in different habitats of northern China.

Science.gov (United States)

Qu, Hao; Zhao, Ha-Lin; Zhao, Xue-Yong; Zuo, Xiao-An; Wang, Shao-Kun; Chen, Min

2017-04-01

Plants that grow in dune ecosystems always suffer from sand burial. Shrubs play implications on the healthy functioning of dune ecosystems due to control blowing sand. However, the survival and growth responses of shrubs to sand burial remain poorly understood. The survival rate and seedling height of two shrubs (Artemisia halodendron and Lespedeza davurica) along with the soil properties under different burial depths were examined in order to reveal the causing ecophysiological attributes of sand burial on shrubs in the desertified region. It was found that A. halodendron can survive a burial depth of 6 cm greater than its seedling height, which is a dominant shrub in mobile dunes with intense burial, whereas a burial depth equivalent to three fourths of its seedling height is detrimental to L. davurica, which is dominant in fixed dunes with less burial. The reasons for the shrub death under sand burial were associated with the physical barrier to vertical growth and the reduction in photosynthetic area. In conclusion, A. halodendron can facilitate the stabilization of mobile dunes because of their high tolerance to the frequent and intensive sand burial, while L. davurica can be beneficial for the recovery process because of their higher survival rates under shallow burial following restoration of mobile dunes.

Extent of Stream Burial and Relationships to Watershed Area, Topography, and Impervious Surface Area

Directory of Open Access Journals (Sweden)

Roy E. Weitzell

2016-11-01

Full Text Available Stream burial—the routing of streams through culverts, pipes, and concrete lined channels, or simply paving them over—is common during urbanization, and disproportionately affects small, headwater streams. Burial undermines the physical and chemical processes governing life in streams, with consequences for water quality and quantity that may amplify from headwaters to downstream receiving waters. Knowledge of the extent of stream burial is critical for understanding cumulative impacts to stream networks, and for future decision-making allowing for urban development while protecting ecosystem function. We predicted stream burial across the urbanizing Potomac River Basin (USA for each 10-m stream segment in the basin from medium-resolution impervious cover data and training observations obtained from high-resolution aerial photography in a GIS. Results were analyzed across a range in spatial aggregation, including counties and independent cities, small watersheds, and regular spatial grids. Stream burial was generally correlated with total impervious surface area (ISA, with areas exhibiting ISA above 30% often subject to elevated ratios of stream burial. Recurring patterns in burial predictions related to catchment area and topographic slope were also detected. We discuss these results in the context of physiographic constraints on stream location and urban development, including implications for environmental management of aquatic resources.

Evaluation of the ORNL area for future waste burial facilities

International Nuclear Information System (INIS)

Lomenick, T.F.; Byerly, D.W.; Gonzales, S.

1983-10-01

Additional waste-burial facilities will be needed at ORNL within this decade. In order to find environmentally acceptable sites, the ORNL area must be systematically evaluated. This document represents the first step in that selection process. Geologic and hydrologic data from the literature and minor field investigations are used to identify more favorable sites for Solid Waste Storage Area (SWSA) 7. Also underway at this time is a companion study to locate a Central Waste Storage Area which could be used in the future to accommodate wastes generated by the X-10, Y-12, and K-25 facilities. From the several watershed options available, the Whiteoak Creek drainage basin is selected as the most promising hydrologic regime. This area contains all past and present waste-disposal facilities and is thus already well monitored. The seven bedrock units within the ORNL area are evaluated as potential burial media. Shales of the Conasauga Group, which are currently used for waste burial in the Whiteoak Creek drainage basin, and the Knox Group are considered the leading candidates. Although the residuum derived from and overlying the Knox dolomite has many favorable characteristics and may be regarded as having a high potential for burial of low-level wastes, at the present it is unproven. Therefore, the Conasauga shales are considered a preferable option for SWSA 7 within the ORNL area. Since the Conasauga interval is currently used for waste burial, it is better understood. One tract in Melton Valley that is underlain by Conasauga shales is nominated for detailed site-characterization studies, and several other tracts are recommended for future exploratory drilling. Exploration is also suggested for a tract in the upper Whiteoak Creek basin where Knox residuum is the shallow subsurface material

Sarmatian Burials Near the Astanino Village in the Eastern Crimea