Development of Core Simulator (CoSi) for APR1400 And Analysis of LPPT Result using APR1400-CoSi

International Nuclear Information System (INIS)

Moon, Sang-Rae; Kim, Yong-Bae; Lee, Eun-Ki

2014-01-01

According to NRC guidelines, Low Power Physics Test (LPPT) is required to be performed in low temperature/low pressure (160 .deg. C/42.2 kg/cm 2 ) as well as NOT/NOP (291.3 .deg. C/158.2 kg/cm 2 ) because Shin-Kori Unit 3 is FOAK nuclear power plant. Low Power Physics Test (LPPT) is essential to verify the nuclear design and robustness of reactor safety. LPPT consists of initial criticality, Point of Adding Heat (POAH), All Rod Out (ARO) Boron Concentration, Isothermal Temperature Coefficient (ITC), Control Rod Worth measurements and so on. KHNP-CRI has developed the Core Simulator for APR1400 (APR1400-CoSi) in order to improve the ability performing the LPPT. Especially, APR1400-CoSi has enhanced capability to calculate the full Core neutronic parameters by revising RAST-K that is three dimensional real time core kinetic program. APR1400-CoSi has been developed for education-training of Low Power Physics Test(LPPT). Particularly, APR1400-CoSi has an enhanced capability to calculate the full core neutronic parameters by revising RAST-K which is a three dimensional real time core kinetics program. Low Power Physics Test (LPPT) was performed using APR1400-CoSi and the results showed very similar values with the predicted ones. In other words, the initial core model of Shin-Kori Unit 3 in APR1400-CoSi system has been verified to be appropriate enough. Also, it was confirmed that the test range of Low Power Physics Test (LPPT) reamains effective even though the largest incremental bank reactivity is inserted in core by analyzing the power change during the rod SWAP test

Multi-objective optimization for nuclear fleet evolution scenarios using COSI - 5187

International Nuclear Information System (INIS)

Freynet, D.; Coquelet-Pascal, C.; Eschbach, R.; Krivtchik, G.; Merle-Lucotte, E.

2015-01-01

The consequences of strategic choices on material inventories and flux in the fuel cycle can be analysed with the COSI code. Indeed COSI enables to compare various fleet evolution options (e.g. new reactor systems deployment) and different nuclear materials management (e.g. plutonium multi-recycling). COSI is coupled with the CESAR depletion code. In this paper a methodology for the nuclear fleet evolution scenarios optimization using COSI is introduced. A large number of scenario calculations is needed to solve an optimization problem, which makes infeasible an optimization calculation using the COSI/CESAR version. Given that CESAR calculations represent about 95% of the COSI computation time, CESAR irradiation surrogate models carrying out with ANN regression method and cooling analytic models have been coupled with COSI. An example of optimization study is presented involving 2 discrete variables related to the number of deployed SFR to renew the French PWR fleet and 2 criteria: minimizing the natural uranium consumption and the number of produced HLW vitrified packages

Forschungszentrum Juelich, Institut fuer Kernphysik/COSY. Annual report 2009

International Nuclear Information System (INIS)

Buescher, Markus; Hanhart, Christoph; Krewald, Siegfried; Machner, Hartmut; Maier, Rudolf; Meissner, Ulf G.; Ritman, James; Stockhorst, Hans; Stroeher, Hans

2010-05-01

The following topics were dealt with: Physics at COSY, COSY operation and developments, further experimental activities, theoretical investigations, preparation of the HESR, the PANDA experiment. (HSI)

Forschungszentrum Juelich, Institut fuer Kernphysik/COSY. Annual report 2009

Energy Technology Data Exchange (ETDEWEB)

Buescher, Markus; Hanhart, Christoph; Krewald, Siegfried; Machner, Hartmut; Maier, Rudolf; Meissner, Ulf G.; Ritman, James; Stockhorst, Hans; Stroeher, Hans (eds.)

2010-05-15

The following topics were dealt with: Physics at COSY, COSY operation and developments, further experimental activities, theoretical investigations, preparation of the HESR, the PANDA experiment. (HSI)

Forschungszentrum Juelich, Institut fuer Kernphysik/COSY. Annual report 2010

Energy Technology Data Exchange (ETDEWEB)

Buescher, Markus; Grzonka, Dieter; Hanhart, Christoph; Krewald, Siegfried; Maier, Rudolf; Meissner, Ulf G.; Ritman, James; Stockhorst, Hans; Stroeher, Hans (eds.)

2011-04-15

The following topics are dealt with: Physics at COSY, COSY operation and developments, further experimental activities, theoretical investigations, preparation of the HESR, the PANDA experiments. (HSI)

Forschungszentrum Juelich, Institut fuer Kernphysik/COSY. Annual report 2010

International Nuclear Information System (INIS)

Buescher, Markus; Grzonka, Dieter; Hanhart, Christoph; Krewald, Siegfried; Maier, Rudolf; Meissner, Ulf G.; Ritman, James; Stockhorst, Hans; Stroeher, Hans

2011-04-01

The following topics are dealt with: Physics at COSY, COSY operation and developments, further experimental activities, theoretical investigations, preparation of the HESR, the PANDA experiments. (HSI)

Forschungszentrum Juelich, Institut fuer Kernphysik/COSY. Annual report 2007

Energy Technology Data Exchange (ETDEWEB)

Buescher, M.; Hanhart, C.; Krewald, S.; Machner, H.; Maier, R.; Meissner, U.G.; Ritman, J.; Stockhorst, H.; Stroeher, H. (eds.)

2008-03-15

The following topics are dealt with, Physics at COSY, external experiments, theoretical investigations. COSY operation and developments, preparation for FAIR. See hints under the relevant topics. (HSI)

Forschungszentrum Juelich, Institut fuer Kernphysik/COSY. Annual report 2007

International Nuclear Information System (INIS)

Buescher, M.; Hanhart, C.; Krewald, S.; Machner, H.; Maier, R.; Meissner, U.G.; Ritman, J.; Stockhorst, H.; Stroeher, H.

2008-03-01

The following topics are dealt with, Physics at COSY, external experiments, theoretical investigations. COSY operation and developments, preparation for FAIR. See hints under the relevant topics. (HSI)

Growth of CoSi2 on Si(001) by reactive deposition epitaxy

International Nuclear Information System (INIS)

Lim, C.W.; Shin, C.-S.; Gall, D.; Zuo, J.M.; Petrov, I.; Greene, J.E.

2005-01-01

CaF 2 -structure CoSi 2 layers were formed on Si(001) by reactive deposition epitaxy (RDE) and compared with CoSi 2 layers obtained by conventional solid phase growth (SPG). In both sets of experiments, Co was deposited by ultrahigh-vacuum magnetron sputtering and CoSi 2 formed at 600 deg. C. However, in the case of RDE, CoSi 2 formation occurred during Co deposition while for SPG, Co was deposited at 25 deg. C and silicidation took place during subsequent annealing. X-ray diffraction pole figures and transmission electron microscopy results demonstrate that RDE CoSi 2 layers are epitaxial with a cube-on-cube relationship (001) CoSi 2 parallel (001) Si and [100] CoSi 2 parallel[100] Si . In contrast, SPG films are polycrystalline with an average grain size of ≅1000 A and a mixed 111/002/022/112 orientation. We attribute the striking difference to rapid Co diffusion into the Si(001) substrate during RDE for which the high Co/Si reactivity gives rise to a flux-limited reaction resulting in the direct formation of the disilicide phase. In contrast, sequential nucleation and transformation among increasingly Si-rich phases--from orthorhombic Co 2 Si to cubic CoSi to CoSi 2 --during SPG results in polycrystalline layers with a complex texture

COSY INFINITY, a new arbitrary order optics code

International Nuclear Information System (INIS)

Berz, M.

1990-01-01

The new arbitrary order particle optics and beam dynamics code COSY INFINITY is presented. The code is based on differential algebraic (DA) methods. COSY INFINITY has a full structured object oriented language environment. This provides a simple interface for the casual or novice user. At the same time, it offers the advanced user a very flexible and powerful tool for the utilization of DA. The power and generality of the environment is perhaps best demonstrated by the fact that the physics routines of COSY INFINITY are written in its own input language. The approach also facilitates the implementation of new features because special code generated by a user can be readily adopted to the source code. Besides being very compact in size, the code is also very fast, thanks to efficiently programmed elementary DA operations. For simple low order problems, which can be handled by conventional codes, the speed of COSY INFINITY is comparable and in certain cases even higher

Status of the cooler synchrotron COSY Juelich. Papers

International Nuclear Information System (INIS)

1994-09-01

The eight papers present the status of COSY, operational characteristics of the COSY electron cooler, a broad-band multiple-harmonic acceleration structure, diagnostic tools, a stochastic cooling system, a narrow-band digital RF-noise generator, an RF-synthesizer, and a longitudinal phase space tracking of particles in a multiple harmonic RF-system. (DG)

The collaborative ec project ReCosy - 16203

International Nuclear Information System (INIS)

Kienzler, Bernhard; Buckau, Gunnar

2009-01-01

The Collaborative Project (CP) ReCosy (Redox Controlling Systems) was established in 2008. It falls within the EURATOM program and is implemented within the European Commission's 7. Framework Program. Main objectives of CP ReCosy are the sound understanding of redox phenomena controlling the long-term release/retention of radionuclides in nuclear waste disposal and providing tools to apply the results to Performance Assessment/Safety Case. Although redox is not a new geochemical problem, different questions are still not resolved and thus raised by implementers and scientists. Radionuclide redox transformations on minerals are considered to be decisive scenarios in various FEP lists. 32 institutions from 13 European countries contribute to the 4-years CP by i) development of advanced analytical tools, ii) investigations of processes responsible for redox control (thermodynamically and kinetically controlled processes, surface reactions and microbial processes), iii) provision of required data on redox controlling processes, and iv) response of the disposal systems to external/internal disturbances. Systems which are investigated comprise simple very well defined ones under controlled laboratory conditions, complex laboratory systems, near-natural systems in the laboratory, real systems, and near-field systems controlled spent nuclear fuel. The scientific results of the CP ReCosy are reported during annual workshops (AW). The first AW took place in February 10-12, 2009. The scientific contributions underwent a peer review and are published in the form of workshop proceedings together with scientific-technical overview papers of the different project work packages. The present paper summarizes the main results obtained after the first year of ReCosy. The status during the project preparation phase of the CP ReCosy is published elsewhere. (authors)

Protective relay

International Nuclear Information System (INIS)

Lim, Mu Ji; Jung, Hae Sang

1974-10-01

This book is divided into two chapters, which deals with protective relay. The first chapter deals with the basic knowledge of relay on development of relay, classification of protective relay, rating of protective relay general structure of protective relay, detecting of ground protection, about point of contact, operating relay and trip relaying. The second chapter is about structure and explanation of relay on classification by structure such as motor type and moving-coil type, explanation of other relays over current relay, over voltage relay, short voltage relay, relay for power, relay for direction, test of over voltage relay, test of short voltage relay and test of directional circuit relay.

Thermal expansion and thermal diffusivity properties of Co-Si solid solutions and intermetallic compounds

International Nuclear Information System (INIS)

Ruan, Ying; Li, Liuhui; Gu, Qianqian; Zhou, Kai; Yan, Na; Wei, Bingbo

2016-01-01

Highlights: • Length change difference between rapidly and slowly solidified Co-Si alloy occurs at high temperature. • Generally CTE increases with an increasing Si content. • The thermal diffusion abilities are CoSi 2 > Co 95 Si 5 > Co 90 Si 10 > Co 2 Si > CoSi if T exceeds 565 K. • All the CTE and thermal diffusivity variations with T satisfy linear or polynomial relations. - Abstract: The thermal expansion of Co-Si solid solutions and intermetallic compounds was measured via dilatometric method, compared with the results of first-principles calculations, and their thermal diffusivities were investigated using laser flash method. The length changes of rapidly solidified Co-Si alloys are larger than those of slowly solidified alloys when temperature increases to around 1000 K due to the more competitive atom motion. The coefficient of thermal expansion (α) of Co-Si alloy increases with an increasing Si content, except that the coefficient of thermal expansion of Co 95 Si 5 influenced by both metastable structure and allotropic transformation is lower than that of Co 90 Si 10 at a higher temperature. The thermal expansion abilities of Co-Si intermetallic compounds satisfy the relationship of Co 2 Si > CoSi > CoSi 2 , and the differences of the coefficients of thermal expansion between them increase with the rise of temperature. The thermal diffusivity of CoSi 2 is evidently larger than the values of other Co-Si alloys. If temperature exceeds 565 K, their thermal diffusion abilities are CoSi 2 > Co 95 Si 5 > Co 90 Si 10 > Co 2 Si > CoSi. All the coefficient of thermal expansion and thermal diffusivity variations with temperature satisfy linear or polynomial relations.

COSY 5.0 - the fifth order code for corpuscular optical systems

International Nuclear Information System (INIS)

Berz, M.; Hoffmann, H.C.; Wollnik, H.

1987-01-01

COSY 5.0 is a new computer code for the design of corpuscular optical systems based on the principle of transfer matrices. The particle optical calculations include all image aberrations through fifth order. COSY 5.0 uses canonical coordinates and exploits the symplectic condition to increase the speed of computation. COSY 5.0 contains a library for the computation of matrix elements of all commonly used corpuscular optical elements such as electric and magnetic multipoles and sector fields. The corresponding formulas were generated algebraically by the computer code HAMILTON. Care was taken that the optimization of optical elements is achieved with minimal numerical effort. Finally COSY 5.0 has a very general mnemonic input code resembling a higher programming language. (orig.)

Methyl labeling and TROSY NMR spectroscopy of proteins expressed in the eukaryote Pichia pastoris

International Nuclear Information System (INIS)

Clark, Lindsay; Zahm, Jacob A.; Ali, Rustam; Kukula, Maciej; Bian, Liangqiao; Patrie, Steven M.; Gardner, Kevin H.; Rosen, Michael K.; Rosenbaum, Daniel M.

2015-01-01

13 C Methyl TROSY NMR spectroscopy has emerged as a powerful method for studying the dynamics of large systems such as macromolecular assemblies and membrane proteins. Specific 13 C labeling of aliphatic methyl groups and perdeuteration has been limited primarily to proteins expressed in E. coli, preventing studies of many eukaryotic proteins of physiological and biomedical significance. We demonstrate the feasibility of efficient 13 C isoleucine δ1-methyl labeling in a deuterated background in an established eukaryotic expression host, Pichia pastoris, and show that this method can be used to label the eukaryotic protein actin, which cannot be expressed in bacteria. This approach will enable NMR studies of previously intractable targets

JUELICH: COSY acceleration and cooling

International Nuclear Information System (INIS)

Anon.

1993-01-01

The COSY cooler synchrotron at the KFA Forschungszentrum Jülich, inaugurated on 1 April, is now well on its way towards precision-defined high energy beams to open new fields for Jülich physics experiments. In two important goals, on 25 May the first beam cooled by electrons circulated inside the accelerator, then on 25 July physicists succeeded in accelerating the beam from the 270 MeV/c injection momentum to 600 MeV. Shortly after, this was pushed well above 1 GeV. Throughout the tuning process the number of stored particles increased steadily, finally peaking at 1.1 x 10 11 , a value compatible with the predicted limit at the injection energy. This success was the result of a painstaking search for the optimum parameter set, the commissioning crew being acutely aware that bringing such a large machine on line was a major experiment in its own right. The 3.3 GeV/c COSY machine belongs to the new class of hadron storage and cooler synchrotrons which started with CERN's LEAR low energy antiproton ring. COSY will 'sharpen' its beams to a narrow momentum spread using both electron and stochastic cooling to control the circulating particles. In addition it will provide space for internal experiments. Both features will allow for novel experimental approaches, and more than 100 physicists are eagerly waiting for the first proton reactions in their detectors

Disorder dependent half-metallicity in Mn2CoSi inverse Heusler alloy

International Nuclear Information System (INIS)

Singh, Mukhtiyar; Saini, Hardev S.; Thakur, Jyoti; Reshak, Ali H.; Kashyap, Manish K.

2013-01-01

Heusler alloys based thin-films often exhibit a degree of atomic disorder which leads to the lowering of spin polarization in spintronic devices. We present ab-initio calculations of atomic disorder effects on spin polarization and half-metallicity of Mn 2 CoSi inverse Heusler alloy. The five types of disorder in Mn 2 CoSi have been proposed and investigated in detail. The A2 a -type and B2-type disorders destroy the half-metallicity whereas it sustains for all disorders concentrations in DO 3a - and A2 b -type disorder and for smallest disorder concentration studied in DO 3b -type disorder. Lower formation energy/atom for A2 b -type disorder than other four disorders in Mn 2 CoSi advocates the stability of this disorder. The total magnetic moment shows a strong dependence on the disorder and the change in chemical environment. The 100% spin polarization even in the presence of disorders explicitly supports that these disorders shall not hinder the use of Mn 2 CoSi inverse Heusler alloy in device applications. - Graphical abstract: Minority-spin gap (E g↓ ) and HM gap (E sf ) as a function of concentrations of various possible disorder in Mn 2 CoSi inverse Heusler alloy. The squares with solid line (black color)/dotted line (blue color)/dashed line (red color) reperesents E g↓ for DO 3a -/DO 3b -/A2 b -type disorder in Mn 2 CoSi and the spheres with solid line (black color)/dottedline (blue color)/dashed line (red color) represents E sf for DO 3a -/DO 3b -/A2 b -type disorder in Mn 2 CoSi. - Highlights: • The DO 3 - and A2-type disorders do not affect the half-metallicity in Mn 2 CoSi. • The B2-type disorder solely destroys half-metallicity in Mn 2 CoSi. • The A2-type disorder most probable to occur out of all three types. • The total spin magnetic moment strongly depends on the disorder concentrations

Test of time-reversal invariance at COSY

Energy Technology Data Exchange (ETDEWEB)

Valdau, Yury [Helmholtz Institut fuer Strahlen- und Kernphysik, Bonn Univ. (Germany); National Research Center ' ' Kurchatov Institute' ' Petersburg Nuclear Physics Institute B.P. Konstantinov, Gatchina (Russian Federation); Eversheim, Dieter [Helmholtz Institut fuer Strahlen- und Kernphysik, Bonn Univ. (Germany); Lorentz, Bernd [Forschungszentrum Juelich, Institute fuer Kernphysik (Germany)

2016-07-01

The experiment to test the Time Reversal Invariance at Cosy (TRIC) is under the preparation by the PAX collaboration. It is planned to improve present limit on the T-odd P-even interaction by at least one order of magnitude using a unique genuine null observable available in double polarized proton-deuteron scattering. The TRIC experiment is planned as a transmission experiment using a tensor polarized deuterium target placed at the internal target place of the Cooler-Synchrotron COSY-Juelich. Total double polarized cross section will be measured observing a beam current change due to the interaction of a polarized proton beam with an internal tensor polarized deuterium target from the PAX atomic beam source. Hence, in this experiment COSY will be used as an accelerator, detector and ideal zero degree spectrometer. In addition to the high intensity polarized proton beam and high density polarized deuterium target, a new high precision beam current measurement system will be prepared for the TRIC experiment. In this report status of all the activities of PAX collaboration towards realization of the TRIC experiment will be presented.

Tracking studies towards EDM measurements at COSY

Energy Technology Data Exchange (ETDEWEB)

Rosenthal, Marcel [Institut fuer Kernphysik, Forschungszentrum Juelich, Juelich (Germany); Physikalisches Institut III B, RWTH Aachen, Aachen (Germany)

2015-07-01

Electric Dipole Moments (EDMs) violate parity and time reversal symmetries. Therefore, direct measurements of charged particles' EDMs would be a strong hint for physics beyond the Standard Model. The JEDI collaboration investigates the feasibility of such measurements for protons, deuterons, and Helium3 in storage rings. Precursor studies are performed at the existing conventional Cooler Synchtrotron COSY in Juelich. A measurement time of about 1000 seconds is proposed. This requires a setup providing a long spin coherence time in the plane perpendicular to the invariant spin axis. During the measurement run, it is planned to use radiofrequency devices to create an EDM related signal. The contribution of imperfections, which could mimic such a signal, is explored in beam and spin dynamics simulations. The software framework COSY INFINITY is used to calculate transfer maps of the magnets and performs long term tracking studies. Recent efforts extend the code by the EDM contribution to spin motion and by the calculation of timedependent maps required for tracking in nonstatic fields. These enhancements are benchmarked with analytical predictions and with test measurements at COSY.

Future physics program at COSY

International Nuclear Information System (INIS)

Grzonka, D.; Kilian, K.

2001-01-01

At the COSY cooler synchrotron several experimental facilities are in operation at internal and external target stations. The combination of a high quality low emittance proton beam with high acceptance detector systems allows precise and kinematically complete experiments. The momentum range of the COSY beam from 300 MeV/c up to about 3.5 GeV/c opens a large field of experimental studies. Data have been taken in various reaction channels from elementary p-p interactions up to reactions on complex target nuclei resulting in a data base of high precision. These studies will be continued and extended to more detailed investigations in the future. Differential cross section distributions also for more than two body reactions will be extracted. By controlling the isospin and spin degrees of freedom the complexity will be reduced. Of specific interest are channels with strangeness. (orig.)

Simulation and correction of the closed orbit in the cooler synchrotron COSY

International Nuclear Information System (INIS)

Dinev, D.

1990-11-01

In this paper the problem of COSY closed orbit control and its correction is discussed. The results of a simulation of the COSY closed orbit and its correction using different correction methods are given. The interactive computer program ORBIT, created especially for the simulation and correction of the COSY closed orbit, is described. The paper includes as well a survey of the orbit correction methods and related topics. (orig.)

New type magnetoresistance in Co/Si systems

International Nuclear Information System (INIS)

Honda, S.; Ishikawa, T.; Takai, K.; Mitarai, Y.; Harada, H.

2005-01-01

The magnetoresistance (MR) properties in both the sputter-deposited Co/Si multilayers and the system consisting of Co evaporated on the anodized Si have been examined. In the Co/Si multilayers, at room temperature both the sharp ordinary magnetoresistance (OMR) and the negative granular-type giant magnetoresistance (GMR) appear, while at low temperatures only the large OMR of about 3.5% is observed for in-plane field. In the Co/anodized-Si system, at room temperature the MR is negligibly small, while it increases steeply with decreasing temperature and very large OMR of about 22% is obtained at 110 K for perpendicular field

Online control package for COSY-TOF experiment

Energy Technology Data Exchange (ETDEWEB)

Borodina, Ekaterina [Institute fuer Kernphysik I, Forschungszentrum Juelich GmbH, 52325, Juelich (Germany); Moscow State Institute of Electronics and Mathematics (Russian Federation); Roderburg, Eduard; Ritman, James [Institute fuer Kernphysik I, Forschungszentrum Juelich GmbH, 52325, Juelich (Germany)

2009-07-01

The new Straw Tube Tracker and Quirl Microstrip detectors have been installed at the TOF (Time Of Flight) experiment at the COSY accelerator in IKP FZ-Juelich. These new detectors increase the number of channels of the COSY-TOF detector by about a factor of 3. Therefore, a new control package to adjust electronic parameters and for control the proper functionality of all channels is being developed. The online controlling based on visualization of key parameters of detectors plays an important role. The concept and the techniques of the online software package are developed for the COSY-TOF experiment. It consists of conversion software, which transforms a binary data stream from the DAQ to detector oriented event format, methods of IPC (Inter-Process Communications), and GUI (graphical user interface). To achieve data transfer through the network and real time data performance the IPC tools - sockets and shared memory are used. A special GUI, TOF-ONLINE has been developed, based on ROOT. The GUI allows the detectors, plotting spectra, resetting data, etc., to be selected in an intuitive way. Examples of the visualization and the results of the first beam time will be introduced.

New developments on COSI6, the simulation software for fuel cycle analysis

Energy Technology Data Exchange (ETDEWEB)

Meyer, Maryan; Boucher, Lionel [CEA, DEN, DER, SPRC, LECy, Centre de Cadarache, Batiment 230, Saint-Paul-lez-Durance, 13108 (France)

2009-06-15

New developments on COSI6, the simulation software for fuel cycle analysis 'COSI', is a code simulating a pool of nuclear electricity generating plants with its associated fuel cycle facilities. This code has been designed to study various short, medium and long term options for the introduction of various types of nuclear reactors and for the use of associated nuclear materials. COSI calculates the mass and the isotopic composition of all the materials, in each part of the nuclear park, at any time. Following the complete renewal of the code in 2006, new developments have been implemented into improve physical models, user convenience and to enlarge the scope of utilisation. COSI can now be coupled with CESAR 5 (JEFF 2.2: 200 FP available), allowing to perform waste packages calculations: high level waste (glasses), intermediate level waste (compacted waste), liquid and gaseous waste coming from processing, reactor high level waste. Those packages are managed in new kinds of facilities: finished warehouse, interim storage, waste disposal. The calculable features for waste packages are: mass (initial heavy metal), isotopic content, packages mass, packages volume, number of packages, activity, radiotoxicity, decay heat, necessary area. Developments on COSI are still ongoing. The reactivity equivalence function (based on Baker formula) is now available: - for thorium cycle: compositions for [Th+Pu] or [Th+U] can be calculated taking into account all nuclides impacts. - for ADS: compositions for [MA+Pu] can be calculated taking into account all nuclides impacts. The physical model is also developed: nuclear data (branching ratios, fission energies, fission yields) will be different between thermal reactors and fast reactors. The first step towards proliferation resistance methodology implementation is the evaluation of physical data needed for proliferation evaluation: heating rate from Pu in material (Watt/kg), weight fraction of even isotopes

Measurement of {sup 1}H-{sup 15}N and {sup 1}H-{sup 13}C residual dipolar couplings in nucleic acids from TROSY intensities

Energy Technology Data Exchange (ETDEWEB)

Ying Jinfa [National Institutes of Health, Laboratory of Chemical Physics, National Institute of Diabetes and Digestive and Kidney Diseases (United States); Wang Jinbu [National Cancer Institute, National Institutes of Health, Structural Biophysics Laboratory (United States); Grishaev, Alex [National Institutes of Health, Laboratory of Chemical Physics, National Institute of Diabetes and Digestive and Kidney Diseases (United States); Yu Ping; Wang Yunxing [National Cancer Institute, National Institutes of Health, Structural Biophysics Laboratory (United States); Bax, Ad, E-mail: bax@nih.gov [National Institutes of Health, Laboratory of Chemical Physics, National Institute of Diabetes and Digestive and Kidney Diseases (United States)

2011-09-15

Analogous to the recently introduced ARTSY method for measurement of one-bond {sup 1}H-{sup 15}N residual dipolar couplings (RDCs) in large perdeuterated proteins, we introduce methods for measurement of base {sup 13}C-{sup 1}H and {sup 15}N-{sup 1}H RDCs in protonated nucleic acids. Measurements are based on quantitative analysis of intensities in {sup 1}H-{sup 15}N and {sup 13}C-{sup 1}H TROSY-HSQC spectra, and are illustrated for a 71-nucleotide adenine riboswitch. Results compare favorably with those of conventional frequency-based measurements in terms of completeness and convenience of use. The ARTSY method derives the size of the coupling from the ratio of intensities observed in two TROSY-HSQC spectra recorded with different dephasing delays, thereby minimizing potential resonance overlap problems. Precision of the RDC measurements is limited by the signal-to-noise ratio, S/N, achievable in the 2D TROSY-HSQC reference spectrum, and is approximately given by 30/(S/N) Hz for {sup 15}N-{sup 1}H and 65/(S/N) Hz for {sup 13}C-{sup 1}H. The signal-to-noise ratio of both {sup 1}H-{sup 15}N and {sup 1}H-{sup 13}C spectra greatly benefits when water magnetization during the experiments is not perturbed, such that rapid magnetization transfer from bulk water to the nucleic acid, mediated by rapid amino and hydroxyl hydrogen exchange coupled with {sup 1}H-{sup 1}H NOE transfer, allows for fast repetition of the experiment. RDCs in the mutated helix 1 of the riboswitch are compatible with nucleotide-specifically modeled, idealized A-form geometry and a static orientation relative to the helix 2/3 pair, which differs by ca 6 Degree-Sign relative to the X-ray structure of the native riboswitch.

Opportunistic relaying in multipath and slow fading channel: Relay selection and optimal relay selection period

KAUST Repository

Sungjoon Park,

2011-11-01

In this paper we present opportunistic relay communication strategies of decode and forward relaying. The channel that we are considering includes pathloss, shadowing, and fast fading effects. We find a simple outage probability formula for opportunistic relaying in the channel, and validate the results by comparing it with the exact outage probability. Also, we suggest a new relay selection algorithm that incorporates shadowing. We consider a protocol of broadcasting the channel gain of the previously selected relay. This saves resources in slow fading channel by reducing collisions in relay selection. We further investigate the optimal relay selection period to maximize the throughput while avoiding selection overhead. © 2011 IEEE.

Stochastic cooling system in COSY

International Nuclear Information System (INIS)

Brittner, P.; Hacker, H.U.; Prasuhn, D.; Schug, G.; Singer, H.; Spiess, W.; Stassen, R.

1994-01-01

The stochastic cooler system in COSY is designed for proton kinetic energies between 0.8 and 2.5 GeV. Fabrication of the mechanical parts of the system is going on. Test results of the prototype measurements as well as data of the active RF-compontens are presented. (orig.)

Stochastic cooling system in COSY

Energy Technology Data Exchange (ETDEWEB)

Brittner, P [Forschungszentrum Juelich GmbH (Germany); Hacker, H U [Forschungszentrum Juelich GmbH (Germany); Prasuhn, D [Forschungszentrum Juelich GmbH (Germany); Schug, G [Forschungszentrum Juelich GmbH (Germany); Singer, H [Forschungszentrum Juelich GmbH (Germany); Spiess, W [Forschungszentrum Juelich GmbH (Germany); Stassen, R [Forschungszentrum Juelich GmbH (Germany)

1994-09-01

The stochastic cooler system in COSY is designed for proton kinetic energies between 0.8 and 2.5 GeV. Fabrication of the mechanical parts of the system is going on. Test results of the prototype measurements as well as data of the active RF-compontens are presented. (orig.)

COSY INFINITY version 8

International Nuclear Information System (INIS)

Makino, Kyoko; Berz, Martin

1999-01-01

The latest version of the particle optics code COSY INFINITY is presented. Using Differential Algebraic (DA) methods, the code allows the computation of aberrations of arbitrary field arrangements to in principle unlimited order. Besides providing a general overview of the code, several recent techniques developed for specific applications are highlighted. These include new features for the direct utilization of detailed measured fields as well as rigorous treatment of remainder bounds

Interfacial stability of CoSi2/Si structures grown by molecular beam epitaxy

Science.gov (United States)

George, T.; Fathauer, R. W.

1992-01-01

The stability of CoSi2/Si interfaces was examined in this study using columnar silicide structures grown on (111) Si substrates. In the first set of experiments, Co and Si were codeposited using MBE at 800 C and the resulting columnar silicide layer was capped by epitaxial Si. Deposition of Co on the surface of the Si capping layer at 800 C results in the growth of the buried silicide columns. The buried columns grow by subsurface diffusion of the deposited Co, suppressing the formation of surface islands of CoSi2. The column sidewalls appear to be less stable than the top and bottom interfaces, resulting in preferential lateral growth and ultimately in the coalescence of the columns to form a continuous buried CoSi2 layer. In the second set of experiments, annealing of a 250 nm-thick buried columnar layer at 1000 C under a 100 nm-thick Si capping layer results in the formation of a surface layer of CoSi2 with a reduction in the sizes of the CoSi2 columns. For a sample having a thicker Si capping layer the annealing leads to Ostwald ripening producing buried equiaxed columns. The high CoSi2/Si interfacial strain could provide the driving force for the observed behavior of the buried columns under high-temperature annealing.

Recent physics at COSY – A review

Indian Academy of Sciences (India)

Abstract. The COSY accelerator in Jülich is presented together with its internal and external detectors. The physics program performed recently is discussed with emphasis on strangeness physics and precision experiments.

Ner protein of phage Mu: Assignments using {sup 13}C/{sup 15}N-labeled protein

Energy Technology Data Exchange (ETDEWEB)

Strzelecka, T.; Gronenborn, A.M.; Clore, G.M. [National Institutes of Health, Bethesda, MD (United States)

1994-12-01

The Ner protein is a small (74-amino acid) DNA-binding protein that regulates a switch between the lysogenic and lytic stages of phage Mu. It inhibits expression of the C repressor gene and down-regulates its own expression. Two-dimensional NMR experiments on uniformly {sup 15}N-labeled protein provided most of the backbone and some of the sidechain proton assignments. The secondary structure determination using two-dimensional NOESY experiments showed that Ner consists of five {alpha}-helices. However, because most of the sidechain protons could not be assigned, the full structure was not determined. Using uniformly {sup 13}C/{sup 15}N-labeled Ner and a set of three-dimensional experiments, we were able to assign all of the backbone and 98% of the sidechain protons. In particular, the CBCANH and CBCA(CO)NH experiments were used to sequentially assign the C{alpha} and C{beta} resonances; the HCCH-CTOCSY and HCCH-COSY were used to assign sidechain carbon and proton resonances.

New experimental results on electron cooling at COSY-Juelich

International Nuclear Information System (INIS)

Dietrich, J.; Maier, R.; Prasuhn, D.; Stein, H.J.; Kobets, A.; Meshkov, I.; Sidorin, A.; Smirnov, A.

2007-01-01

Recent results of electron cooling of proton beams at COSY-Juelich are reported. Cooling at an electron energy of 70 keV has been studied for the first time. At the injection energy level of COSY, corresponding to 24.5 keV electron energy, the features of the cooled proton beam at extremely low intensities have been investigated in order to find out whether an ordering of the proton beam can be achieved. Such investigations are motivated by the results of a numerical simulation of the ordering process by the BETACOOL code. (author)

Band structure and unconventional electronic topology of CoSi

Science.gov (United States)

Pshenay-Severin, D. A.; Ivanov, Y. V.; Burkov, A. A.; Burkov, A. T.

2018-04-01

Semimetals with certain crystal symmetries may possess unusual electronic structure topology, distinct from that of the conventional Weyl and Dirac semimetals. Characteristic property of these materials is the existence of band-touching points with multiple (higher than two-fold) degeneracy and nonzero Chern number. CoSi is a representative of this group of materials exhibiting the so-called ‘new fermions’. We report on an ab initio calculation of the electronic structure of CoSi using density functional methods, taking into account the spin-orbit interactions. The linearized \

Multiobjective optimization for nuclear fleet evolution scenarios using COSI

Directory of Open Access Journals (Sweden)

Freynet David

2016-01-01

Full Text Available The consequences of various fleet evolution options on material inventories and flux in fuel cycle and waste can be analysed by means of transition scenario studies. The COSI code is currently simulating chronologically scenarios whose parameters are fully defined by the user and is coupled with the CESAR depletion code. As the interactions among reactors and fuel cycle facilities can be complex, and the ways in which they may be configured are many, the development of optimization methodology could improve scenario studies. The optimization problem definition needs to list: (i criteria (e.g. saving natural resources and minimizing waste production; (ii variables (scenario parameters related to reprocessing, reactor operation, installed power distribution, etc.; (iii constraints making scenarios industrially feasible. The large number of scenario calculations needed to solve an optimization problem can be time-consuming and hardly achievable; therefore, it requires the shortening of the COSI computation time. Given that CESAR depletion calculations represent about 95% of this computation time, CESAR surrogate models have been developed and coupled with COSI. Different regression models are compared to estimate CESAR outputs: first- and second-order polynomial regressions, Gaussian process and artificial neural network. This paper is about a first optimization study of a transition scenario from the current French nuclear fleet to a Sodium Fast Reactors fleet as defined in the frame of the 2006 French Act for waste management. The present article deals with obtaining the optimal scenarios and validating the methodology implemented, i.e. the coupling between the simulation software COSI, depletion surrogate models and a genetic algorithm optimization method.

Alternate transmission with half-duplex relaying in MIMO interference relay networks

KAUST Repository

Park, Seongho

2013-12-01

In this paper, we consider an alternate transmission scheme for a multiple-input multiple-output interference relay channel where multiple sources transmit their own signals to their corresponding destinations via one of two relaying groups alternately every time phase. Each of the relaying groups has arbitrary number of relays, and each relay operates in half-duplex amplify-and-forward mode. In our scheme, the received signals at the relay nodes consist of desired signals and two different interference signals such as the inter-source interferences and the inter-group interferences which are caused by the phase incoherence of relaying. As such, we propose an iterative interference alignment algorithm to mitigate the interferences. We show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying system in the interference relay channels. © 2013 IEEE.

The COSY control system, a distributed realtime operating system: First practical experience at the COSY-injector

International Nuclear Information System (INIS)

Stephan, M.; Hacker, U.; Henn, K.; Richert, A.; Sobotta, K.; Weinert, A.

1991-01-01

The COSY control system is hierarchically organized with distributed intelligence and autonomous processing units for dedicated components. Data communication is performed via LAN and over a fieldbus. The hostsystems are UNIX-based, whereas the field-controllers are running a modular realtime operating-system RT/OS which has been developed at KFA. The computer-hardware consists of RISC mini computers, VME-computers in the field and G64 equipment-control-module in geographical expansion of the controller by a fieldbus based on the PDV-standard. The man-machine interface consists of X-window based work stations. On top of X-window a graphical user interface based on object oriented methods is used. A distributed realtime data base allows access to the accelerator state from every workstation. A special highlevel language debugger hosted on the UNIX based workstation and connected over LAN to the VME targets will be used. Together with the software development system for UNIX applications an uniform view of the system appears to the programmer. First practical experience at the COSY injector is presented

Alternate MIMO relaying with three AF relays using interference alignment

KAUST Repository

Park, Kihong

2012-06-01

In this paper, we study a two-hop half-duplex relaying network with one source, one destination, and three amplify-and-forward (AF) relays equipped with M antennas each. We consider alternate transmission to compensate for the inherent loss of capacity pre-log factor 1/2 in half duplex mode, where source transmit message to two relays and the other relay alternately. The inter-relay interference caused by alternate transmission is aligned to make additional degrees of freedom (DOFs). It is shown that the proposed scheme enables us to exploit 3M/4 DOFs compared with the M/2 DOFs of conventional AF relaying. More specifically, suboptimal linear filter designs for a source and three relays are proposed to maximize the achievable sum-rate. We verify using some selected numerical results that the proposed filter designs give significant improvement of the sum-rate over a naive filter and conventional relaying schemes. © 2012 IEEE.

Relay race

CERN Multimedia

Staff Association

2011-01-01

The CERN relay race will take place around the Meyrin site on Thursday 19th May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on the course, and how to register your team for the relay race, can be found at: https://espace.cern.ch/Running-Club/CERN-Relay Some advice for all runners from the medical service can also be found here: https://espace.cern.ch/Running-Club/CERN-Relay/RelayPagePictures/MedicalServiceAnnoncement.pdf

Relay race

CERN Document Server

Staff Association

2011-01-01

The CERN relay race will take place around the Meyrin site on Thursday 19th May starting at 12·15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on the course, and how to register your team for the relay race, can be found at: https://espace.cern.ch/Running-Club/CERN-Relay Some advice for all runners from the medical service can also be found here: https://espace.cern.ch/Running-Club/CERN-Relay/RelayPagePictures/MedicalServiceAnnoncement.pdf

Status and future plans of polarized beams at COSY

Science.gov (United States)

Lorentz, B.; Gebel, R.; Lehrach, A.; Maier, R.; Prasuhn, D.; Stockhorst, H.

2011-05-01

In this paper we report on the present status and future plans of polarized beams in the COSY synchrotron ring. COSY is a synchrotron ring in the momentum range from 295 to 3700 MeV/c. Polarized deuterons and protons are routinely delivered to experiments over the whole momentum range. No depolarization occurs during the acceleration of deuterons in COSY. For polarized protons many depolarizing resonances are crossed without polarization loss. At imperfection resonances, vertical steerer magnets are used to increase the resonance strength, leading to a complete polarization reversal. At intrinsic resonances a fast tune jump quadrupole is used to quickly cross the resonances without loss of polarization. Typical proton polarizations are close to 0.8 below 2.1 GeV/c and about 0.6 for higher momenta. During recent operation an induced depolarizing resonance was used for accurate determination of the relative momentum spread dp/p of the stored beam yielding an accuracy of better than 10-4. For spin filter studies of the PAX collaboration a low beta target section was installed in 2009 and was successfully put into operation early 2010. An upgrade of the EDDA polarimeter electronics and data acquisition system is underway to ensure continued availability of the polarimeter, which is essential for the polarized proton operation of COSY. In the near future it is planned to install a Siberian snake solenoid of 4.5 Tm to be able to provide in addition to vertically polarized protons, longitudinal polarization as well. This solenoid will allow the preparation of a longitudinally polarized beam up to a kinetic energy of 500 MeV.

First internal and external experiments at COSY Juelich

International Nuclear Information System (INIS)

Prasuhn, D.; Maier, R.; Bechstedt, U.; Dietrich, J.; Hacker, U.; Martin, S.; Stockhorst, H.; Toelle, R.; Grzonka, D.; Nake, C.; Mosel, F.

1995-01-01

The inauguration of the cooler synchrotron COSY Juelich was celebrated on April 1st, 1993. After the first successful acceleration to proton momenta above 800 GeV/c, beamtimes for experiments were scheduled in parallel to further machine development. The first experiment was the internal target experiment EDDA, which investigated the energy dependence of the p-p interaction. It makes use of a 3x4 μm 2 thin CH 2 fiber as an internal target. The thickness of the fiber is more than adequate to achieve high luminosities, so the intensity of the stored beam has to be reduced to 10 7 p. On the other hand, it is thin enough to achieve beam lifetimes of 3 s at 1.4 GeV/c. Details of the target fabrication and the first experimental results will be discussed. Both external experimental facilities at COSY, the time-of-flight spectrometer, and the magnetic spectrometer BIG KARL use a liquid hydrogen (deuterium) target. The first experiments were carried out at proton energies between 300 MeV and 500 MeV. Also, these experimental data will be presented. Two further internal experiments are prepared for the installation into the COSY ring. The target for the first experiment is a gas-jet target, the second experiment uses ribbon targets for the interaction. The status of both experimental setups will be shown. (orig.)

Expert system for COSY-Control

International Nuclear Information System (INIS)

Bongers, N.; Dahmen, B.; Danzglock, R.; Hacker, H.U.; Hardt, A.; Henkel, C.; Henn, K.; Launer, J.; Martin, S.A.; Nau, K.; Ollech, O.; Peischard, S.; Richert, A.K.; Singer, H.; Sobotta, K.; Schug, G.; Spiess, W.; Weinert, A.; Weynen, D.; Rohling, C.

1988-01-01

This paper is an overview of the COSY- Control-System. It is based on several layers with different tasks. The first layer is necessary for the interaction between man and machine, the database and the modelling of experiments. The second layer serves the different components of the COSY-MACHINE such as watch-dog function, power- converters, diagnostic, instrumentation, cooling, vacuum, beam-line and injection. The third layer is for direct process controlling. The connection between the layers are made by a Local Area Network based on an IEEE 802.3 protocol. The first step in the realization of this Control-System is to use HP-9000 workstations in connection with HP-9000 minicomputers as workcells. The integration to the peripherie-controller such as power-converters and diagnostic-elements are made by VME-Bus-Crates which are also wired to a LAN based on IEEE 802.3. A possible hardware solution as far as the VME-Bus integration is concerned is the link between Hewlett Packard Precision Architecture computers (HP-PA) and a VME-Bus interface board named IBAM which is able to drive an IEEE 802.3 protocol. For the interfacing to the process are several VME-Bus boards with computing-power, memory, digital I/O and function-generators responsible

Reactive relay selection in underlay cognitive networks with fixed gain relays

KAUST Repository

Hussain, Syed Imtiaz

2012-06-01

Best relay selection is a bandwidth efficient technique for multiple relay environments without compromising the system performance. The problem of relay selection is more challenging in underlay cognitive networks due to strict interference constraints to the primary users. Generally, relay selection is done on the basis of maximum end-to-end signal to noise ratio (SNR). However, it requires large amounts of channel state information (CSI) at different network nodes. In this paper, we present and analyze a reactive relay selection scheme in underlay cognitive networks where the relays are operating with fixed gains near a primary user. The system model minimizes the amount of CSI required at different nodes and the destination selects the best relay on the basis of maximum relay to destination SNR. We derive close form expressions for the received SNR statistics, outage probability, bit error probability and average channel capacity of the system. Simulation results are also presented to confirm the validity of the derived expressions. © 2012 IEEE.

COSY, proposal for a cooler synchrotron at the KFA Julich

International Nuclear Information System (INIS)

Berg, G.P.A.; Gaul, G.; Hacker, H.

1986-01-01

The Cooler Synchrotron COSY is being planned in cooperation between scientists of the Kernforschungsanlage Julich, nuclear physicists of the neighbouring universities and other interested scientists. COSY is designed to provide beams of very light ions with energies ranging from 40 MeV to a maximum of 2.5 GeV for protons. This energy range allows a variety of studies in the so called energy window between 150 and 500 MeV, and it permits different kinds of investigations in the medium-energy region including the KΛ-threshold. Both electron cooling and stochastic cooling are foreseen in order to obtain very high phase-space density. The existing isochronous cyclotron JULIC will serve as injector. COSY will contain two bending sections, each consisting of three unit cells, and two long straight sections between the bends. Large flexibility is guaranteed by the ion-optical design. Experiments are being planned that make use either of the high quality external beam prepared by slow extraction or of the very high luminosity that is effective in the recirculator mode of operation

New developments and prospects on COSI, the simulation software for fuel cycle analysis

Energy Technology Data Exchange (ETDEWEB)

Eschbach, R.; Meyer, M.; Coquelet-Pascal, C.; Tiphine, M.; Krivtchik, G.; Cany, C. [Atomic Energy and Alternative Energies Commission - CEA, CEA-Cadarache, DEN, DER, SPRC, F-13108 Saint-Paul-lez-Durance (France)

2013-07-01

COSI, software developed by the Nuclear Energy Direction of the CEA, is a code simulating a pool of nuclear power plants with its associated fuel cycle facilities. This code has been designed to study various short, medium and long term options for the introduction of various types of nuclear reactors and for the use of associated nuclear materials. In the frame of the French Act for waste management, scenario studies are carried out with COSI, to compare different options of evolution of the French reactor fleet and options of partitioning and transmutation of plutonium and minor actinides. Those studies aim in particular at evaluating the sustainability of Sodium cooled Fast Reactors (SFR) deployment and the possibility to transmute minor actinides. The COSI6 version is a completely renewed software released in 2006. COSI6 is now coupled with the last version of CESAR (CESAR5.3 based on JEFF3.1.1 nuclear data) allowing the calculations on irradiated fuel with 200 fission products and 100 heavy nuclides. A new release is planned in 2013, including in particular the coupling with a recommended database of reactors. An exercise of validation of COSI6, carried out on the French PWR historic nuclear fleet, has been performed. During this exercise quantities like cumulative natural uranium consumption, or cumulative depleted uranium, or UOX/MOX spent fuel storage, or stocks of reprocessed uranium, or plutonium content in fresh MOX fuel, or the annual production of high level waste, have been computed by COSI6 and compared to industrial data. The results have allowed us to validate the essential phases of the fuel cycle computation, and reinforces the credibility of the results provided by the code.

The COSY control system

International Nuclear Information System (INIS)

Bongers, N.; Hacker, U.; Henn, K.; Richert, A.; Simon, M.; Sobotta, K.; Stephan, M.; Vashegyi, T.; Weinert, A.

1992-01-01

The COSY control system architecture is organized strongly hierarchically with distributed intelligence and extensive use of standards. At the top level of computer control hardware work stations give the operator graphical access to the process. For these tasks Hewlett Packard HP 9000 Series 700 computers with HP-UX and X-Windows/Motif are in use. Also used as work-cells this RISC computers give computing power for model calculations and long term databases. This computers are interconnected using Ethernet and TCP/IP to the next layer of hardware. (author) 3 refs.; 5 figs

Partial relay selection in underlay cognitive networks with fixed gain relays

KAUST Repository

Hussain, Syed Imtiaz; Alouini, Mohamed-Slim; Hasna, Mazen Omar; Qaraqe, Khalid A.

2012-01-01

In a communication system with multiple cooperative relays, selecting the best relay utilizes the available spectrum more efficiently. However, selective relaying poses a different problem in underlay cognitive networks compared to the traditional cooperative networks due to interference thresholds to the primary users. In most cases, a best relay is the one which provides the maximum end-to-end signal to noise ratio (SNR). This approach needs plenty of instantaneous channel state information (CSI). The CSI burden could be reduced by partial relay selection. In this paper, a partial relay selection scheme is presented and analyzed for an underlay cognitive network with fixed gain relays operating in the vicinity of a primary user. The system model is adopted in a way that each node needs minimal CSI to perform its task. The best relay is chosen on the basis of maximum source to relay link SNR which then forwards the message to the destination. We derive closed form expressions for the received SNR distributions, system outage, probability of bit error and average channel capacity of the system. The derived results are confirmed through simulations. © 2012 IEEE.

Partial relay selection in underlay cognitive networks with fixed gain relays

KAUST Repository

Hussain, Syed Imtiaz

2012-05-01

In a communication system with multiple cooperative relays, selecting the best relay utilizes the available spectrum more efficiently. However, selective relaying poses a different problem in underlay cognitive networks compared to the traditional cooperative networks due to interference thresholds to the primary users. In most cases, a best relay is the one which provides the maximum end-to-end signal to noise ratio (SNR). This approach needs plenty of instantaneous channel state information (CSI). The CSI burden could be reduced by partial relay selection. In this paper, a partial relay selection scheme is presented and analyzed for an underlay cognitive network with fixed gain relays operating in the vicinity of a primary user. The system model is adopted in a way that each node needs minimal CSI to perform its task. The best relay is chosen on the basis of maximum source to relay link SNR which then forwards the message to the destination. We derive closed form expressions for the received SNR distributions, system outage, probability of bit error and average channel capacity of the system. The derived results are confirmed through simulations. © 2012 IEEE.

Opportunistic Relay Selection in Multicast Relay Networks using Compressive Sensing

KAUST Repository

Elkhalil, Khalil

2014-12-01

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. However, for relay selection algorithms to make a selection decision, channel state information (CSI) from all cooperating relays is usually required at a central node. This requirement poses two important challenges. Firstly, CSI acquisition generates a great deal of feedback overhead (air-time) that could result in significant transmission delays. Secondly, the fed back channel information is usually corrupted by additive noise. This could lead to transmission outages if the central node selects the set of cooperating relays based on inaccurate feedback information. In this paper, we introduce a limited feedback relay selection algorithm for a multicast relay network. The proposed algorithm exploits the theory of compressive sensing to first obtain the identity of the “strong” relays with limited feedback. Following that, the CSI of the selected relays is estimated using linear minimum mean square error estimation. To minimize the effect of noise on the fed back CSI, we introduce a back-off strategy that optimally backs-off on the noisy estimated CSI. For a fixed group size, we provide closed form expressions for the scaling law of the maximum equivalent SNR for both Decode and Forward (DF) and Amplify and Forward (AF) cases. Numerical results show that the proposed algorithm drastically reduces the feedback air-time and achieves a rate close to that obtained by selection algorithms with dedicated error-free feedback channels.

Optimized Power Allocation and Relay Location Selection in Cooperative Relay Networks

Directory of Open Access Journals (Sweden)

Jianrong Bao

2017-01-01

Full Text Available An incremental selection hybrid decode-amplify forward (ISHDAF scheme for the two-hop single relay systems and a relay selection strategy based on the hybrid decode-amplify-and-forward (HDAF scheme for the multirelay systems are proposed along with an optimized power allocation for the Internet of Thing (IoT. Given total power as the constraint and outage probability as an objective function, the proposed scheme possesses good power efficiency better than the equal power allocation. By the ISHDAF scheme and HDAF relay selection strategy, an optimized power allocation for both the source and relay nodes is obtained, as well as an effective reduction of outage probability. In addition, the optimal relay location for maximizing the gain of the proposed algorithm is also investigated and designed. Simulation results show that, in both single relay and multirelay selection systems, some outage probability gains by the proposed scheme can be obtained. In the comparison of the optimized power allocation scheme with the equal power allocation one, nearly 0.1695 gains are obtained in the ISHDAF single relay network at a total power of 2 dB, and about 0.083 gains are obtained in the HDAF relay selection system with 2 relays at a total power of 2 dB.

Threshold-Based Relay Selection for Detect-and-Forward Relaying in Cooperative Wireless Networks

Directory of Open Access Journals (Sweden)

Fan Yijia

2010-01-01

Full Text Available This paper studies two-hop cooperative demodulate-and-forward relaying using multiple relays in wireless networks. A threshold based relay selection scheme is considered, in which the reliable relays are determined by comparing source-relay SNR to a threshold, and one of the reliable relays is selected by the destination based on relay-destination SNR. The exact bit error rate of this scheme is derived, and a simple threshold function is proposed. It is shown that the network achieves full diversity order ( under the proposed threshold, where is the number of relays in the network. Unlike some other full diversity achieving protocols in the literature, the requirement that the instantaneous/average SNRs of the source-relay links be known at the destination is eliminated using the appropriate SNR threshold.

First internal and external experiments at COSY Juelich

Energy Technology Data Exchange (ETDEWEB)

Prasuhn, D [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Kernphysik; Maier, R [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Kernphysik; Bechstedt, U [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Kernphysik; Dietrich, J [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Kernphysik; Hacker, U [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Kernphysik; Martin, S [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Kernphysik; Stockhorst, H [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Kernphysik; Toelle, R [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Kernphysik; Grzonka, D [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Kernphysik; Nake, C [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Kernphysik; Mosel, F [Bonn Univ. (Germany). Inst. fuer Strahlen- und Kernphysik

1995-08-01

The inauguration of the cooler synchrotron COSY Juelich was celebrated on April 1st, 1993. After the first successful acceleration to proton momenta above 800 GeV/c, beamtimes for experiments were scheduled in parallel to further machine development. The first experiment was the internal target experiment EDDA, which investigated the energy dependence of the p-p interaction. It makes use of a 3x4 {mu}m{sup 2} thin CH{sub 2} fiber as an internal target. The thickness of the fiber is more than adequate to achieve high luminosities, so the intensity of the stored beam has to be reduced to 10{sup 7} p. On the other hand, it is thin enough to achieve beam lifetimes of 3 s at 1.4 GeV/c. Details of the target fabrication and the first experimental results will be discussed. Both external experimental facilities at COSY, the time-of-flight spectrometer, and the magnetic spectrometer BIG KARL use a liquid hydrogen (deuterium) target. The first experiments were carried out at proton energies between 300 MeV and 500 MeV. Also, these experimental data will be presented. Two further internal experiments are prepared for the installation into the COSY ring. The target for the first experiment is a gas-jet target, the second experiment uses ribbon targets for the interaction. The status of both experimental setups will be shown. (orig.).

Feasibility of deuteron break-up study at COSY 0 deg facility (ANKE)

International Nuclear Information System (INIS)

Kacharava, A.K.; Komarov, V.I.; Kulikov, A.V.; Macharashvili, G.G.; Petrus, A.Yu.

1996-01-01

The experimental setup ANKE (Apparatus for study of Nuclear and Kaonic Ejectiles) under construction at the Cooling Synchrotron (COSY, Juelich) is aimed to study a wide class of proton-nucleus reactions. The kinematic conditions, detection efficiencies and useful event selection criteria for the deuteron break-up study at the COSY internal proton beam are considered in this paper. The expected counting rates for the detector systems are also estimated. 16 refs., 11 figs., 3 tabs

A polarized atomic-beam target for COSY-Juelich

International Nuclear Information System (INIS)

Eversheim, P. D.; Altmeier, M.; Felden, O.; Glende, M.; Walker, M.; Hiemer, A.; Gebel, R.

1998-01-01

An atomic-beam target (ABT) for the EDDA experiment has been built in Bonn and was tested for the very first time at the cooler synchrotron COSY. The ABT differs from the polarized colliding-beams ion source for COSY in the DC-operation of the dissociator and the use of permanent 6-pole magnets. At present the beam optics of the ABT is set-up for maximum density in the interaction zone, but for target-cell operation it can be modified to give maximum intensity. The modular concept of this atomic ground-state target allows to provide all vector- (and tensor) polarizations for protons and deuterons, respectively. Up to now the polarization of the atomic-beam could be verified by the EDDA experiment to be > or approx. 80% with a density in the interaction zone of > or approx. 10 11 atoms/cm 2

Telecommunications Relay Services

Science.gov (United States)

... Home » Health Info » Hearing, Ear Infections, and Deafness Telecommunications Relay Services On this page: What are telecommunication ... additional information about telecommunication relay services? What are telecommunication relay services? Title IV of the Americans with ...

Reactive relay selection in underlay cognitive networks with fixed gain relays

KAUST Repository

Hussain, Syed Imtiaz; Alouini, Mohamed-Slim; Qaraqe, Khalid A.; Hasna, Mazen Omar

2012-01-01

Best relay selection is a bandwidth efficient technique for multiple relay environments without compromising the system performance. The problem of relay selection is more challenging in underlay cognitive networks due to strict interference

Individual Channel Estimation in a Diamond Relay Network Using Relay-Assisted Training

Directory of Open Access Journals (Sweden)

Xianwen He

2017-01-01

Full Text Available We consider the training design and channel estimation in the amplify-and-forward (AF diamond relay network. Our strategy is to transmit the source training in time-multiplexing (TM mode while each relay node superimposes its own relay training over the amplified received data signal without bandwidth expansion. The principal challenge is to obtain accurate channel state information (CSI of second-hop link due to the multiaccess interference (MAI and cooperative data interference (CDI. To maintain the orthogonality between data and training, a modified relay-assisted training scheme is proposed to migrate the CDI, where some of the cooperative data at the relay are discarded to accommodate relay training. Meanwhile, a couple of optimal zero-correlation zone (ZCZ relay-assisted sequences are designed to avoid MAI. At the destination node, the received signals from the two relay nodes are combined to achieve spatial diversity and enhanced data reliability. The simulation results are presented to validate the performance of the proposed schemes.

Hadrons and broken symmetries with WASA-at-COSY

Indian Academy of Sciences (India)

Physics of Hadrons and QCD Volume 75 Issue 2 August 2010 pp 225-234 ... is an internal experiment at the cooler synchrotron (COSY) in Jülich, Germany. ... Higher orders in chiral perturbation theory are probed with the → 0 decay.

Properties of ion implanted epitaxial CoSi2/Si(1 0 0) after rapid thermal oxidation

International Nuclear Information System (INIS)

Zhao, Q.T.; Kluth, P.; Xu, J.; Kappius, L.; Zastrow, U.; Wang, Z.L.; Mantl, S.

2000-01-01

Epitaxial CoSi 2 layers were grown on Si(1 0 0) using molecular beam allotaxy. Boron ion implantations and rapid thermal oxidation (RTO) were performed. During oxidation, SiO 2 formed on the surface of the CoSi 2 layers, and the silicides was pushed into the substrate. The diffusion of boron was slightly retarded during oxidation for the specimen with a 20 nm epitaxial CoSi 2 capping layer as compared to the specimen without CoSi 2 capping layer. The electrical measurements showed that the silicide has good Schottky contacts with the boron doped silicon layer after RTO. A nanometer silicide patterning process, based on local oxidation of silicide (LOCOSI) layer, was also investigated. It shows two back-to-back Schottky diodes between the two separated parts of the silicide

Efficient incremental relaying

KAUST Repository

Fareed, Muhammad Mehboob

2013-07-01

We propose a novel relaying scheme which improves the spectral efficiency of cooperative diversity systems by utilizing limited feedback from destination. Our scheme capitalizes on the fact that relaying is only required when direct transmission suffers deep fading. We calculate the packet error rate for the proposed efficient incremental relaying scheme with both amplify and forward and decode and forward relaying. Numerical results are also presented to verify their analytical counterparts. © 2013 IEEE.

Distributed Antenna Channels with Regenerative Relaying: Relay Selection and Asymptotic Capacity

Directory of Open Access Journals (Sweden)

Aitor del Coso

2007-11-01

Full Text Available Multiple-input-multiple-output (MIMO techniques have been widely proposed as a means to improve capacity and reliability of wireless channels, and have become the most promising technology for next generation networks. However, their practical deployment in current wireless devices is severely affected by antenna correlation, which reduces their impact on performance. One approach to solve this limitation is relaying diversity. In relay channels, a set of N wireless nodes aids a source-destination communication by relaying the source data, thus creating a distributed antenna array with uncorrelated path gains. In this paper, we study this multiple relay channel (MRC following a decode-and-forward (D&F strategy (i.e., regenerative forwarding, and derive its achievable rate under AWGN. A half-duplex constraint on relays is assumed, as well as distributed channel knowledge at both transmitter and receiver sides of the communication. For this channel, we obtain the optimum relay selection algorithm and the optimum power allocation within the network so that the transmission rate is maximized. Likewise, we bound the ergodic performance of the achievable rate and derive its asymptotic behavior in the number of relays. Results show that the achievable rate of regenerative MRC grows as the logarithm of the Lambert W function of the total number of relays, that is, 𝒞=log⁡2(W0(N. Therefore, D&F relaying, cannot achieve the capacity of actual MISO channels.

Opportunistic relaying in multipath and slow fading channel: Relay selection and optimal relay selection period

KAUST Repository

Sungjoon Park,; Stark, Wayne E.

2011-01-01

In this paper we present opportunistic relay communication strategies of decode and forward relaying. The channel that we are considering includes pathloss, shadowing, and fast fading effects. We find a simple outage probability formula

Relay Selection for Cooperative Relaying in Wireless Energy Harvesting Networks

Science.gov (United States)

Zhu, Kaiyan; Wang, Fei; Li, Songsong; Jiang, Fengjiao; Cao, Lijie

2018-01-01

Energy harvesting from the surroundings is a promising solution to provide energy supply and extend the life of wireless sensor networks. Recently, energy harvesting has been shown as an attractive solution to prolong the operation of cooperative networks. In this paper, we propose a relay selection scheme to optimize the amplify-and-forward (AF) cooperative transmission in wireless energy harvesting cooperative networks. The harvesting energy and channel conditions are considered to select the optimal relay as cooperative relay to minimize the outage probability of the system. Simulation results show that our proposed relay selection scheme achieves better outage performance than other strategies.

Relay Selection and Resource Allocation in One-Way and Two-Way Cognitive Relay Networks

KAUST Repository

Alsharoa, Ahmad M.

2013-05-08

In this work, the problem of relay selection and resource power allocation in one- way and two-way cognitive relay networks using half duplex channels with different relaying protocols is investigated. Optimization problems for both single and multiple relay selection that maximize the sum rate of the secondary network without degrading the quality of service of the primary network by respecting a tolerated interference threshold were formulated. Single relay selection and optimal power allocation for two-way relaying cognitive radio networks using decode-and-forward and amplify-and-forward protocols were studied. Dual decomposition and subgradient methods were used to find the optimal power allocation. The transmission process to exchange two different messages between two transceivers for two-way relaying technique takes place in two time slots. In the first slot, the transceivers transmit their signals simultaneously to the relay. Then, during the second slot the relay broadcasts its signal to the terminals. Moreover, improvement of both spectral and energy efficiency can be achieved compared with the one-way relaying technique. As an extension, a multiple relay selection for both one-way and two-way relaying under cognitive radio scenario using amplify-and-forward were discussed. A strong optimization tool based on genetic and iterative algorithms was employed to solve the 
formulated optimization problems for both single and multiple relay selection, where discrete relay power levels were considered. Simulation results show that the practical and low-complexity heuristic approaches achieve almost the same performance of the optimal relay selection schemes either with discrete or continuous power distributions while providing a considerable saving in terms of computational complexity.

Threshold hyperon production in proton-proton collisions at COSY-11

International Nuclear Information System (INIS)

Rozek, T.

2005-10-01

For the first time the pp→nK + Σ + reaction has been measured in the threshold region and the cross section was determined. The measurement was performed at the COSY-11 detection system at two beam momenta P beam =2.6 GeV/c and 2.74 GeV/c, corresponding to excess energies Q=13 MeV and 60 MeV. COSY-11 is an internal magnetic spectrometer experiment at the COoler SYnchrotron and storage ring COSY in Juelich, Germany. It is equipped with scintillator hodoscopes and drift chambers for charged particle detection and a scintillator/lead sandwich detector for neutrons. Experimentally, the Σ + hyperon was identified via the missing mass technique, by detecting the remaining reaction products - K + meson and neutron. Extensive background studies in the missing mass spectra have been performed and the possible influence of the higher partial waves on the detection efficiency discussed. The investigation on the Σ + production is a part of the long ongoing studies of the hyperons production performed by the COSY-11 collaboration. In the previous analysis of the Λ and Σ 0 hyperon production in the pp→pK + Λ and pp→pK + Σ 0 reactions, respectively, the unexpectedly high cross section ratio σ(Λ/σ)(Σ 0 ) in the close to threshold region was observed. To explain this behavior, various theoretical scenarios were proposed, but although they differ even in the dominant basic reaction mechanism, all more or less reproduce the data. In order to get more information for disentangling the contributing reaction mechanisms, data from an other isospin channel were taken, namely pp→nK + Σ + . Within this thesis the method of the measurement and the data analysis is given. The total cross section is presented and the results are discussed in view of available theoretical models. (orig.)

Joint source and relay optimization for interference MIMO relay networks

Science.gov (United States)

Khandaker, Muhammad R. A.; Wong, Kai-Kit

2017-12-01

This paper considers multiple-input multiple-output (MIMO) relay communication in multi-cellular (interference) systems in which MIMO source-destination pairs communicate simultaneously. It is assumed that due to severe attenuation and/or shadowing effects, communication links can be established only with the aid of a relay node. The aim is to minimize the maximal mean-square-error (MSE) among all the receiving nodes under constrained source and relay transmit powers. Both one- and two-way amplify-and-forward (AF) relaying mechanisms are considered. Since the exactly optimal solution for this practically appealing problem is intractable, we first propose optimizing the source, relay, and receiver matrices in an alternating fashion. Then we contrive a simplified semidefinite programming (SDP) solution based on the error covariance matrix decomposition technique, avoiding the high complexity of the iterative process. Numerical results reveal the effectiveness of the proposed schemes.

Status of COSY

International Nuclear Information System (INIS)

Maier, R.; Bechstedt, U.; Dietrich, J.; Hacker, U.; Martin, S.; Prasuhn, D.; Rossen, P. v.; Stockhorst, H.; Toelle, R.

1994-01-01

COSY Juelich is a cooler synchrotron and storage ring with a proton momentum range from 270 to 3300 MeV/c. It has been conceived to deliver high precision beams for medium energy physics. To accomplish this goal two cooling systems are used. An electron-cooling system that reaches up to a momentum of 645 MeV/c and a stochastic cooling system that covers the upper momentum range from 1500 to 3300 MeV/c. Since its inauguration in April 1993 substantial progress in developing beams for the experiments has been achieved and the physics program has started with first measurements. Proton beams in a wide energy range have been delivered to internal as well external experiments. Important design features of the machine and results of the commissioning process are presented. (orig.)

Status of COSY

Energy Technology Data Exchange (ETDEWEB)

Maier, R [Inst. fuer Kernphysik, Forschungszentrum Juelich GmbH (Germany); Bechstedt, U [Inst. fuer Kernphysik, Forschungszentrum Juelich GmbH (Germany); Dietrich, J [Inst. fuer Kernphysik, Forschungszentrum Juelich GmbH (Germany); Hacker, U [Inst. fuer Kernphysik, Forschungszentrum Juelich GmbH (Germany); Martin, S [Inst. fuer Kernphysik, Forschungszentrum Juelich GmbH (Germany); Prasuhn, D [Inst. fuer Kernphysik, Forschungszentrum Juelich GmbH (Germany); Rossen, P v [Inst. fuer Kernphysik, Forschungszentrum Juelich GmbH (Germany); Stockhorst, H [Inst. fuer Kernphysik, Forschungszentrum Juelich GmbH (Germany); Toelle, R [Inst. fuer Kernphysik, Forschungszentrum Juelich GmbH (Germany)

1994-09-01

COSY Juelich is a cooler synchrotron and storage ring with a proton momentum range from 270 to 3300 MeV/c. It has been conceived to deliver high precision beams for medium energy physics. To accomplish this goal two cooling systems are used. An electron-cooling system that reaches up to a momentum of 645 MeV/c and a stochastic cooling system that covers the upper momentum range from 1500 to 3300 MeV/c. Since its inauguration in April 1993 substantial progress in developing beams for the experiments has been achieved and the physics program has started with first measurements. Proton beams in a wide energy range have been delivered to internal as well external experiments. Important design features of the machine and results of the commissioning process are presented. (orig.)

Alternate transmission relaying based on interference alignment in 3-relay half-duplex MIMO systems

KAUST Repository

Park, Seongho; Park, Kihong; Ko, Youngchai; Alouini, Mohamed-Slim

2012-01-01

In a half-duplex relaying, the capacity pre-log factor 1/2 is a major drawback in spectral efficiency. This paper proposes a linear precoding/decoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help the communication between the source and the destination. In our proposed scheme, we consider a phase incoherent method in relays in which the source alternately transmits message signals to the different relays. In addition, we propose a linear interference alignment scheme which can suppress the inter-relay interference resulting from the phase incoherence of relaying. Based on our analysis of degrees of freedom and our simulation results, we show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying. © 2012 IEEE.

Alternate transmission relaying based on interference alignment in 3-relay half-duplex MIMO systems

KAUST Repository

Park, Seongho

2012-09-01

In a half-duplex relaying, the capacity pre-log factor 1/2 is a major drawback in spectral efficiency. This paper proposes a linear precoding/decoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help the communication between the source and the destination. In our proposed scheme, we consider a phase incoherent method in relays in which the source alternately transmits message signals to the different relays. In addition, we propose a linear interference alignment scheme which can suppress the inter-relay interference resulting from the phase incoherence of relaying. Based on our analysis of degrees of freedom and our simulation results, we show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying. © 2012 IEEE.

Coordinated Direct and Relay Transmission with Linear Non-Regenerative Relay Beamforming

DEFF Research Database (Denmark)

Sun, Fan; De Carvalho, Elisabeth; Popovski, Petar

2012-01-01

Joint processing of multiple communication flows in wireless systems has given rise to a number of novel transmission techniques, notably the two-way relaying, but also more general traffic scenarios, such as coordinated direct and relay (CDR) transmissions. In a CDR scheme the relay has a central...... role in managing the interference and boosting the overall system performance. In this letter we consider the case in which an amplify-and-forward relay has multiple antennas and can use beamforming to support the coordinated transmissions. We focus on one representative traffic type with one uplink...... user and one downlink user. Two different criteria for relay beamforming are analyzed: maximal weighted sum-rate and maximization of the worst-case weighted SNR. We propose iterative optimal solutions, as well as low-complexity near-optimal solutions....

Radioisotope relay instrument

International Nuclear Information System (INIS)

Pozdnyakov, V.N.; Sazonov, O.L.; Taksar, I.M.; Tesnavs, Eh.R.; Yanushkovskij, V.A.

1974-01-01

The paper describes a radioisotope relay device containing a radiation source, a detector, an electronic relay block with a comparative threshold mechanism. The device differs from previously known ones in that, for the purpose of increasing stability and speed of action, the electronic relay block is a separate unit and contains two threshold pulse generators which are joined up, across series-connected ''and'' and ''or'' elements, with one of the inputs of the comparative threshold mechanism, whose second input is connected with a detector and whose outputs are connected with a relay element connected by feedback with the above-mentioned ''and'' elements. (author)

Structural characterization of oxidized allotaxially grown CoSi2 layers by x-ray scattering

International Nuclear Information System (INIS)

Kaendler, I. D.; Seeck, O. H.; Schlomka, J.-P.; Tolan, M.; Press, W.; Stettner, J.; Kappius, L.; Dieker, C.; Mantl, S.

2000-01-01

A series of buried CoSi 2 layers prepared by a modified molecular beam epitaxy process (allotaxy) and a subsequent wet-oxidation process was investigated by x-ray scattering. The oxidation time which determines the depth in which the CoSi 2 layers are located within the Si substrates has been varied during the preparation. The electron density profiles and the structure of the interfaces were extracted from specular reflectivity and diffuse scattering measurements. Crystal truncation rod investigations yielded the structure on an atomic level (crystalline quality). It turns out that the roughness of the CoSi 2 layers increases drastically with increasing oxidation time, i.e., with increasing depth of the buried layers. Furthermore, the x-ray data reveal that the oxidation growth process is diffusion limited. (c) 2000 American Institute of Physics

Decode and Zero-Forcing Forward Relaying with Relay Selection in Cognitive Radio Systems

KAUST Repository

Park, Kihong

2014-05-01

In this paper, we investigate a cognitive radio (CR) relay network with multiple relay nodes that help forwarding the signal of CR users. Best relay selection is considered to take advantage of its low complexity of implementation. When the primary user (PU) is located close to the relay nodes, the performance of the secondary network is severely degraded due to the interference power constraint during the transmission in the second hop. We propose a decode and zero-forcing forward scheme to suppress the interference power at the relay nodes and analyze the statistics of the end-to-end signal-to-noise ratio when the relay nodes are located arbitrarily and experience therefore non-identical Rayleigh fading channels. Numerical results validate our theoretical results and show that our proposed scheme improves the performance of the CR network when the PU is close to the relay nodes. © 2014 IEEE.

COSY Juelich - a cooler synchrotron for unpolarized and polarized medium-energy studies

International Nuclear Information System (INIS)

Seyfarth, H.

2001-01-01

Full text: The Forschungszentrum Juelich (Research Center Juelich) is one of the sixteen national research institutions in the 'Hermann von Helmholtz Association of German Research Centers'. It is dedicated to fundamental and applied research and development which can be summarized under five priorities: (i) structure of matter and materials research, (ii) information technology, (iii) life sciences, (iv) environment precaution research, and (v) energy technology. As one of the institutes within (i). the Institut fur Kernphysik (Institute for Nuclear Research) operates the COSY cooler synchrotron which allows to accelerate unpolarized and polarized protons and deuterons to the maximum momentum of 3450 MeV/c (2640 MeV and 2050 MeV kinetic energy for protons and deuterons, respectively). At low energy electron cooling can be used for beam preparation, whereas stochastic cooling can be applied to the accelerated beam. In the first years of operation since 1993 the experiments have been performed with the unpolarized proton beam. Since 1997 the polarized proton beam is available with increasing intensity and a typical degree of polarization of about 75 % up to the maximum beam energy. In 2000 the first unpolarized deuteron beam could be accelerated and stored at the maximum energy. Four target places exist for the internal experiments PISA. EDDA, COSY-II, and ANKE which use the circulating beam with thin solid strip or fiber targets and gas targets. The four experiments TOF, MOMO, GEM, NESSI, and JESSICA are using external beams. The programs of the experiments JESSICA (Juelich Experimental Spallation Setup in the COSY Area), NESSI (Neutron Scintillator and Silicon), and PISA (Proton Induced Spallation) aim at the measurement of data needed or the design of the target station of the planned European Spallation neutron Source (ESS). The set-up of PISA is replacing the earlier experiment COSY-13 which successfully completed its investigations on the production of

On the achievable degrees of freedom of alternate MIMO relaying with multiple AF relays

KAUST Repository

Park, Kihong

2012-03-01

In this paper, we consider a two-hop relaying network where one source, one destination, and multiple amplify-and-forward (AF) relays equipped with M antennas operate in a half-duplex mode. In order to compensate for the inherent loss of capacity pre-log factor of 1/2 due to half-duplex relaying, we propose a new transmission protocol which combines alternate relaying and inter-relay interference alignment. We prove that the proposed scheme can (i) exploits M degrees of freedom (DOFs) and (ii) perfectly recover the pre-log factor loss if the number of relays is at least six. From our selected numerical results, we show that our proposed scheme gives significant improvement over conventional AF relaying which offers only M/2 DOFs. © 2012 IEEE.

Advanced Strategic and Tactical Relay Request Management for the Mars Relay Operations Service

Science.gov (United States)

Allard, Daniel A.; Wallick, Michael N.; Gladden, Roy E.; Wang, Paul; Hy, Franklin H.

2013-01-01

This software provides a new set of capabilities for the Mars Relay Operations Service (MaROS) in support of Strategic and Tactical relay, including a highly interactive relay request Web user interface, mission control over relay planning time periods, and mission management of allowed strategic vs. tactical request parameters. Together, these new capabilities expand the scope of the system to include all elements critical for Tactical relay operations. Planning of replay activities spans a time period that is split into two distinct phases. The first phase is called Strategic, which begins at the time that relay opportunities are identified, and concludes at the point that the orbiter generates the flight sequences for on board execution. Any relay request changes from this point on are called Tactical. Tactical requests, otherwise called Orbit - er Relay State Changes (ORSC), are highly restricted in terms of what types of changes can be made, and the types of parameters that can be changed may differ from one orbiter to the next. For example, one orbiter may be able to delay the start of a relay request, while another may not. The legacy approach to ORSC management involves exchanges of e-mail with "requests for change" and "acknowledgement of approval," with no other tracking of changes outside of e-mail folders. MaROS Phases 1 and 2 provided the infrastructure for strategic relay for all supported missions. This new version, 3.0, introduces several capabilities that fully expand the scope of the system to include tactical relay. One new feature allows orbiter users to manage and "lock" Planning Periods, which allows the orbiter team to formalize the changeover from Strategic to Tactical operations. Another major feature allows users to interactively submit tactical request changes via a Web user interface. A third new feature allows orbiter missions to specify allowed tactical updates, which are automatically incorporated into the tactical change process

Relay Precoder Optimization in MIMO-Relay Networks With Imperfect CSI

KAUST Repository

Pandarakkottilil, Ubaidulla

2011-11-01

In this paper, we consider robust joint designs of relay precoder and destination receive filters in a nonregenerative multiple-input multiple-output (MIMO) relay network. The network consists of multiple source-destination node pairs assisted by a MIMO-relay node. The channel state information (CSI) available at the relay node is assumed to be imperfect. We consider robust designs for two models of CSI error. The first model is a stochastic error (SE) model, where the probability distribution of the CSI error is Gaussian. This model is applicable when the imperfect CSI is mainly due to errors in channel estimation. For this model, we propose robust minimum sum mean square error (SMSE), MSE-balancing, and relay transmit power minimizing precoder designs. The next model for the CSI error is a norm-bounded error (NBE) model, where the CSI error can be specified by an uncertainty set. This model is applicable when the CSI error is dominated by quantization errors. In this case, we adopt a worst-case design approach. For this model, we propose a robust precoder design that minimizes total relay transmit power under constraints on MSEs at the destination nodes. We show that the proposed robust design problems can be reformulated as convex optimization problems that can be solved efficiently using interior-point methods. We demonstrate the robust performance of the proposed design through simulations. © 2011 IEEE.

CoSi2 growth on Si(001) by reactive deposition epitaxy: Effects of high-flux, low-energy ion irradiation

International Nuclear Information System (INIS)

Lim, C. W.; Greene, J. E.; Petrov, I.

2006-01-01

CoSi 2 layers, CoSi 2 (parallel sign)(001) Si and [100] CoSi 2 (parallel sign)[100] Si , contain fourfold symmetric (111) twinned domains oriented such that (221) CoSi 2 (parallel sign)(001) Si and CoSi 2 (parallel sign)[110] Si . We demonstrate that high-flux low-energy (E Ar + =9.6 eV) Ar + ion irradiation during deposition dramatically increases the area fraction f u of untwinned regions from 0.17 in films grown under standard magnetically balanced conditions in which the ratio J Ar + /J Co of the incident Ar + to Co fluxes is 1.4 to 0.72 with J Ar + /J Co =13.3. TEM analyses show that the early stages of RDE CoSi 2 (001) film growth proceed via the Volmer-Weber mode with independent nucleation of both untwinned and twinned islands. Increasing J Ar + /J Co results in larger values of both the number density and area of untwinned with respect to twinned islands. The intense Ar + ion bombardment creates additional low-energy adsorption sites that favor the nucleation of untwinned islands while collisionally enhancing Co surface mobilities which, in turn, increases the probability of itinerant Co adatoms reaching these sites

Threshold hyperon production in proton-proton collisions at COSY-11

Energy Technology Data Exchange (ETDEWEB)

Rozek, T.

2005-10-01

For the first time the pp{yields}nK{sup +}{sigma}{sup +} reaction has been measured in the threshold region and the cross section was determined. The measurement was performed at the COSY-11 detection system at two beam momenta P{sub beam}=2.6 GeV/c and 2.74 GeV/c, corresponding to excess energies Q=13 MeV and 60 MeV. COSY-11 is an internal magnetic spectrometer experiment at the COoler SYnchrotron and storage ring COSY in Juelich, Germany. It is equipped with scintillator hodoscopes and drift chambers for charged particle detection and a scintillator/lead sandwich detector for neutrons. Experimentally, the {sigma}{sup +} hyperon was identified via the missing mass technique, by detecting the remaining reaction products - K{sup +} meson and neutron. Extensive background studies in the missing mass spectra have been performed and the possible influence of the higher partial waves on the detection efficiency discussed. The investigation on the {sigma}{sup +} production is a part of the long ongoing studies of the hyperons production performed by the COSY-11 collaboration. In the previous analysis of the {lambda} and {sigma}{sup 0} hyperon production in the pp{yields}pK{sup +}{lambda} and pp{yields}pK{sup +}{sigma}{sup 0} reactions, respectively, the unexpectedly high cross section ratio {sigma}({lambda}/{sigma})({sigma}{sup 0}) in the close to threshold region was observed. To explain this behavior, various theoretical scenarios were proposed, but although they differ even in the dominant basic reaction mechanism, all more or less reproduce the data. In order to get more information for disentangling the contributing reaction mechanisms, data from an other isospin channel were taken, namely pp{yields}nK{sup +}{sigma}{sup +}. Within this thesis the method of the measurement and the data analysis is given. The total cross section is presented and the results are discussed in view of available theoretical models. (orig.)

Decode and Zero-Forcing Forward Relaying with Relay Selection in Cognitive Radio Systems

KAUST Repository

Park, Kihong; Alouini, Mohamed-Slim

2014-01-01

In this paper, we investigate a cognitive radio (CR) relay network with multiple relay nodes that help forwarding the signal of CR users. Best relay selection is considered to take advantage of its low complexity of implementation. When the primary

Relay Precoder Optimization in MIMO-Relay Networks With Imperfect CSI

KAUST Repository

Pandarakkottilil, Ubaidulla; Chockalingam, A.

2011-01-01

In this paper, we consider robust joint designs of relay precoder and destination receive filters in a nonregenerative multiple-input multiple-output (MIMO) relay network. The network consists of multiple source-destination node pairs assisted by a

Acoustic phonon dispersion of CoSi2

International Nuclear Information System (INIS)

Weiss, L.; Rumyantsev, A.Yu.; Ivanov, A.S.

1985-01-01

The acoustical phonon dispersion curves of CoSi 2 are measured at room temperature along the main symmetry directions by means of coherent one-phonon scattering of thermal neutrons. The dispersion curves are compared with those of Ge, Si, and the fluorite structure types as CaF 2 and UO 2 . From the slope of the phonon dispersion curves at the GAMMA-point the elastic constants have been obtained

CERN Relay Race

CERN Document Server

CERN Running Club

2010-01-01

The CERN relay race will take place around the Meyrin site on Thursday 20 May, starting at 12.15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on the route, and how to register your team for the relay race, can be found at: https://espace.cern.ch/Running-Club/CERN-Relay

Alternate MIMO relaying with three AF relays using interference alignment

KAUST Repository

Park, Kihong; Alouini, Mohamed-Slim

2012-01-01

In this paper, we study a two-hop half-duplex relaying network with one source, one destination, and three amplify-and-forward (AF) relays equipped with M antennas each. We consider alternate transmission to compensate for the inherent loss

80537 based distance relay

DEFF Research Database (Denmark)

Pedersen, Knud Ole Helgesen

1999-01-01

A method for implementing a digital distance relay in the power system is described.Instructions are given on how to program this relay on a 80537 based microcomputer system.The problem is used as a practical case study in the course 53113: Micocomputer applications in the power system.The relay...

Relay Selection and Resource Allocation in One-Way and Two-Way Cognitive Relay Networks

KAUST Repository

Alsharoa, Ahmad M.

2013-01-01

In this work, the problem of relay selection and resource power allocation in one- way and two-way cognitive relay networks using half duplex channels with different relaying protocols is investigated. Optimization problems for both single

A genetic algorithm for multiple relay selection in two-way relaying cognitive radio networks

KAUST Repository

Alsharoa, Ahmad M.; Ghazzai, Hakim; Alouini, Mohamed-Slim

2013-01-01

In this paper, we investigate a multiple relay selection scheme for two-way relaying cognitive radio networks where primary users and secondary users operate on the same frequency band. More specifically, cooperative relays using Amplifyand- Forward

Efficient incremental relaying

KAUST Repository

Fareed, Muhammad Mehboob; Alouini, Mohamed-Slim

2013-01-01

We propose a novel relaying scheme which improves the spectral efficiency of cooperative diversity systems by utilizing limited feedback from destination. Our scheme capitalizes on the fact that relaying is only required when direct transmission

Outage performance of two-way DF relaying systems with a new relay selection metric

KAUST Repository

Hyadi, Amal; Benjillali, Mustapha; Alouini, Mohamed-Slim

2012-01-01

This paper investigates a new constrained relay selection scheme for two-way relaying systems where two end terminals communicate simultaneously via a relay. The introduced technique is based on the maximization of the weighted sum rate of both

76 FR 24442 - Structure and Practices of the Video Relay Service Program; Telecommunications Relay Services and...

Science.gov (United States)

2011-05-02

... same meaning as the terms ``small business,'' ``small organization,'' and ``small governmental...] Structure and Practices of the Video Relay Service Program; Telecommunications Relay Services and Speech-to... Commission's Structure and Practices of the Video Relay Service Program; Telecommunications Relay Services...

First turn simulations in the cooler synchrotron COSY

International Nuclear Information System (INIS)

Dinev, D.

1991-07-01

This paper is devoted to the first turn correction and related problems in particle accelerators of synchrotron type. The paper consists of two parts. The first part is a survey of the existing methods for first turn steering. The second part is entirely devoted to the first turn in the cooler synchrotron COSY which is under assembling in KFA-Julich, Germany. (orig.)

Alternate transmission with half-duplex relaying in MIMO interference relay networks

KAUST Repository

Park, Seongho; Ko, Youngchai; Park, Kihong; Alouini, Mohamed-Slim

2013-01-01

In this paper, we consider an alternate transmission scheme for a multiple-input multiple-output interference relay channel where multiple sources transmit their own signals to their corresponding destinations via one of two relaying groups

Opportunistic Relay Selection With Limited Feedback

KAUST Repository

Eltayeb, Mohammed E.; Elkhalil, Khalil; Bahrami, Hamid Reza; Al-Naffouri, Tareq Y.

2015-01-01

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Generally, relay selection algorithms require channel state information (CSI) feedback from all cooperating relays to make a selection decision

CERN Relay Race

CERN Document Server

2008-01-01

The CERN relay race will take place around the Meyrin site on Thursday 5 June starting at 12:15 p.m. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on how to register your team for the relay race are given on the Staff Association Bulletin web site. You can access the online registration form at: http://cern.ch/club-running-relay/form.html

CERN Relay Race

CERN Document Server

2007-01-01

The CERN relay race will take place around the Meyrin site on Wednesday 23 May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on how to register your team for the relay race are given on the Staff Association Bulletin web site. You can access the online registration form at: http://cern.ch/club-running-relay/form.html

Power system relaying

CERN Document Server

Horowitz, Stanley H; Niemira, James K

2013-01-01

The previous three editions of Power System Relaying offer comprehensive and accessible coverage of the theory and fundamentals of relaying and have been widely adopted on university and industry courses worldwide. With the third edition, the authors have added new and detailed descriptions of power system phenomena such as stability, system-wide protection concepts and discussion of historic outages. Power System Relaying, 4th Edition continues its role as an outstanding textbook on power system protection for senior and graduate students in the field of electric power engineering and a refer

Ion-beam mixed ultra-thin cobalt suicide (CoSi2) films by cobalt sputtering and rapid thermal annealing

Science.gov (United States)

Kal, S.; Kasko, I.; Ryssel, H.

1995-10-01

The influence of ion-beam mixing on ultra-thin cobalt silicide (CoSi2) formation was investigated by characterizing the ion-beam mixed and unmixed CoSi2 films. A Ge+ ion-implantation through the Co film prior to silicidation causes an interface mixing of the cobalt film with the silicon substrate and results in improved silicide-to-silicon interface roughness. Rapid thermal annealing was used to form Ge+ ion mixed and unmixed thin CoSi2 layer from 10 nm sputter deposited Co film. The silicide films were characterized by secondary neutral mass spectroscopy, x-ray diffraction, tunneling electron microscopy (TEM), Rutherford backscattering, and sheet resistance measurements. The experi-mental results indicate that the final rapid thermal annealing temperature should not exceed 800°C for thin (micrographs of the ion-beam mixed and unmixed CoSi2 films reveals that Ge+ ion mixing (45 keV, 1 × 1015 cm-2) produces homogeneous silicide with smooth silicide-to-silicon interface.

MIMO Four-Way Relaying

DEFF Research Database (Denmark)

Liu, Huaping; Sun, Fan; De Carvalho, Elisabeth

2013-01-01

Two-way relaying in wireless systems has initiated a large research effort during the past few years. Nevertheless, it represents only a specific traffic pattern and it is of interest to investigate other traffic patterns where such a simultaneous processing of information flows can bring...... performance advantage. In this paper we consider a \\emph{four-way relaying} multiple-input multiple-output (MIMO) scenario, where each of the two Mobile Stations (MSs) has a two-way connection to the same Base Station (BS), while each connection is through a dedicated Relay Station (RS). The RSs are placed...... the sum-rate of the new scheme for Decode-and-Forward (DF) operational model for the RS. We compare the performance with state-of-the-art reference schemes, based on two-way relaying with DF. The results indicate that the sum-rate of the two-phase four-way relaying scheme largely outperforms the four...

Performance analysis of two-way amplify and forward relaying with adaptive modulation over multiple relay network

KAUST Repository

Hwang, Kyusung; Ko, Youngchai; Alouini, Mohamed-Slim

2011-01-01

In this letter, we propose two-way amplify-and-forward relaying in conjunction with adaptive modulation in order to improve spectral efficiency of relayed communication systems while monitoring the required error performance. We also consider a multiple relay network where only the best relay node is utilized so that the diversity order increases while maintaining a low complexity of implementation as the number of relays increases. Based on the best relay selection criterion, we offer an upper bound on the signal-to-noise ratio to keep the performance analysis tractable. Our numerical examples show that the proposed system offers a considerable gain in spectral efficiency while satisfying the error rate requirements. © 2011 IEEE.

Performance analysis of two-way amplify and forward relaying with adaptive modulation over multiple relay network

KAUST Repository

Hwang, Kyusung

2011-02-01

In this letter, we propose two-way amplify-and-forward relaying in conjunction with adaptive modulation in order to improve spectral efficiency of relayed communication systems while monitoring the required error performance. We also consider a multiple relay network where only the best relay node is utilized so that the diversity order increases while maintaining a low complexity of implementation as the number of relays increases. Based on the best relay selection criterion, we offer an upper bound on the signal-to-noise ratio to keep the performance analysis tractable. Our numerical examples show that the proposed system offers a considerable gain in spectral efficiency while satisfying the error rate requirements. © 2011 IEEE.

Opportunistic Relay Selection With Limited Feedback

KAUST Repository

Eltayeb, Mohammed E.

2015-08-01

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Generally, relay selection algorithms require channel state information (CSI) feedback from all cooperating relays to make a selection decision. This requirement poses two important challenges, which are often neglected in the literature. Firstly, the fed back channel information is usually corrupted by additive noise. Secondly, CSI feedback generates a great deal of feedback overhead (air-time) that could result in significant performance hits. In this paper, we propose a compressive sensing (CS) based relay selection algorithm that reduces the feedback overhead of relay networks under the assumption of noisy feedback channels. The proposed algorithm exploits CS to first obtain the identity of a set of relays with favorable channel conditions. Following that, the CSI of the identified relays is estimated using least squares estimation without any additional feedback. Both single and multiple relay selection cases are considered. After deriving closed-form expressions for the asymptotic end-to-end SNR at the destination and the feedback load for different relaying protocols, we show that CS-based selection drastically reduces the feedback load and achieves a rate close to that obtained by selection algorithms with dedicated error-free feedback. © 1972-2012 IEEE.

Ready, steady… relay!

CERN Multimedia

2008-01-01

Thursday 5 June. With another year comes another success for CERN’s Relay Race. With 76 teams taking part it was the second highest turnout in the race’s history. ‘The Shabbys’ won the relay race in 10 minutes 51 seconds.As popular as ever, this year the relay race took on the atmosphere of a mini carnival. Gathering on the lawn outside Restaurant 1, various stalls and attractions added to the party feeling of the event, with beer courtesy of ‘AGLUP’, the Belgian beer club, and a wandering jazz group entertaining spectators and competitors alike. Reflecting the greater involvement of other associations in the relay race, the president of the Staff Association Clubs Committee, James Purvis, was the guest of honour, launching the start of the race and presenting the prizes. As regular followers of the race could have probably predicted, The Shabbys were once again victorious and claimed first place. The team members th...

QCD physics at hadron storage rings: From COSY to FAIR

Indian Academy of Sciences (India)

1032/cm2/s in interactions with the circulating beam in COSY. ... FAIR will, at the same time, touch upon key aspects in the evolution of the universe, .... is designed as a multi-purpose setup that allows to cover a wide-ranged program in hadron ...

A genetic algorithm for multiple relay selection in two-way relaying cognitive radio networks

KAUST Repository

Alsharoa, Ahmad M.

2013-09-01

In this paper, we investigate a multiple relay selection scheme for two-way relaying cognitive radio networks where primary users and secondary users operate on the same frequency band. More specifically, cooperative relays using Amplifyand- Forward (AF) protocol are optimally selected to maximize the sum rate of the secondary users without degrading the Quality of Service (QoS) of the primary users by respecting a tolerated interference threshold. A strong optimization tool based on genetic algorithm is employed to solve our formulated optimization problem where discrete relay power levels are considered. Our simulation results show that the practical heuristic approach achieves almost the same performance of the optimal multiple relay selection scheme either with discrete or continuous power distributions. Copyright © 2013 by the Institute of Electrical and Electronic Engineers, Inc.

Iterative Relay Scheduling with Hybrid ARQ under Multiple User Equipment (Type II) Relay Environments

KAUST Repository

Nam, Sung Sik

2018-01-09

In this work, we propose an iterative relay scheduling with hybrid ARQ (IRS-HARQ) scheme which realizes fast jump-in/successive relaying and subframe-based decoding under the multiple user equipment (UE) relay environments applicable to the next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed IRS-HARQ aims to increase the achievable data rate by iteratively scheduling a relatively better UE relay closer to the end user in a probabilistic sense, provided that the relay-to-end user link should be operated in an open-loop and transparent mode. The latter is due to the fact that not only there are no dedicated control channels between the UE relay and the end user but also a new cell is not created. Under this open-loop and transparent mode, our proposed protocol is implemented by partially exploiting the channel state information based on the overhearing mechanism of ACK/NACK for HARQ. Further, the iterative scheduling enables UE-to-UE direct communication with proximity that offers spatial frequency reuse and energy saving.

Relay Selection with Limited and Noisy Feedback

KAUST Repository

Eltayeb, Mohammed E.

2016-01-28

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Nonetheless, relay selection algorithms generally require error-free channel state information (CSI) from all cooperating relays. Practically, CSI acquisition generates a great deal of feedback overhead that could result in significant transmission delays. In addition to this, the fed back channel information is usually corrupted by additive noise. This could lead to transmission outages if the central node selects the set of cooperating relays based on inaccurate feedback information. In this paper, we propose a relay selection algorithm that tackles the above challenges. Instead of allocating each relay a dedicated channel for feedback, all relays share a pool of feedback channels. Following that, each relay feeds back its identity only if its effective channel (source-relay-destination) exceeds a threshold. After deriving closed-form expressions for the feedback load and the achievable rate, we show that the proposed algorithm drastically reduces the feedback overhead and achieves a rate close to that obtained by selection algorithms with dedicated error-free feedback from all relays. © 2015 IEEE.

pp Elastic Scattering: New results from EDDA (COSY)

Science.gov (United States)

Scobel, W.

2000-06-01

In the EDDA experiment excitation functions of proton-proton elastic scattering are studied with narrow steps in the projectile momentum range from 0.8 to 3.4 GeV/c and the angular range 35°⩽Θcm⩽90° with a detector providing ΔΘcm≈1.4° resolution and 85% solid angle coverage. Measurements are performed continuously during projectile acceleration in the Cooler Synchrotron COSY. In phase 1 of the experiment spin-averaged differential cross sections dσ/dΩ have been measured with an internal CH2 fiber target; background corrections were derived from measurements with a carbon fiber target and from Monte Carlo simulations of inelastic pp contributions. The results provide excitation functions and angular distributions of high precision and internal consistency. In phase 2 of the experiment excitation functions of the analyzing power AN have been measured using a polarized (P⩾75%) atomic beam target, and those of the polarization correlation parameters ANN, ASS and ASL will be measured lateron with the polarized COSY beam. The measured excitation functions are compared to recent phase shift analyses, and their impact on them is discussed. So far evidence for narrow structures was neither found in the spin averaged cross sections nor in the analyzing powers.

Optimal relay selection and power allocation for cognitive two-way relaying networks

KAUST Repository

Pandarakkottilil, Ubaidulla; Aï ssa, Sonia

2012-01-01

In this paper, we present an optimal scheme for power allocation and relay selection in a cognitive radio network where a pair of cognitive (or secondary) transceiver nodes communicate with each other assisted by a set of cognitive two-way relays

Buffer-Aided Relaying with Adaptive Link Selection

DEFF Research Database (Denmark)

Zlatanov, Nikola; Schober, Robert; Popovski, Petar

2013-01-01

In this paper, we consider a simple network consisting of a source, a half-duplex decode-and-forward relay, and a destination. We propose a new relaying protocol employing adaptive link selection, i.e., in any given time slot, based on the channel state information of the source-relay and the relay......-destination link a decision is made whether the source or the relay transmits. In order to avoid data loss at the relay, adaptive link selection requires the relay to be equipped with a buffer such that data can be queued until the relay-destination link is selected for transmission. We study both delay......-constrained and delay-unconstrained transmission. For the delay-unconstrained case, we characterize the optimal link selection policy, derive the corresponding throughput, and develop an optimal power allocation scheme. For the delay-constrained case, we propose to starve the buffer of the relay by choosing...

Relay Selection with Limited and Noisy Feedback

KAUST Repository

Eltayeb, Mohammed E.; Elkhalil, Khalil; Mas'ud, Abdullahi Abubakar; Al-Naffouri, Tareq Y.

2016-01-01

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Nonetheless, relay selection algorithms generally require error-free channel state information (CSI) from all cooperating relays. Practically, CSI

CERN Relay Race

CERN Multimedia

2009-01-01

The CERN relay race, now in its 39th year, is already a well-known tradition, but this year the organizers say the event will have even more of a festival feeling. Just off the starting line of the CERN relay race.For the past few years, spectators and runners at the CERN relay race have been able to enjoy a beer while listening to music from the CERN music and jazz clubs. But this year the organizers are aiming for "even more of a festival atmosphere". As David Nisbet, President of the CERN running club and organizer of the relay race, says: "Work is not just about getting your head down and doing the theory, it’s also about enjoying the company of your colleagues." This year, on top of music from the Santa Luis Band and the Canettes Blues Band, there will be demonstrations from the Aikido and softball clubs, a stretching session by the Fitness club, as well as various stalls and of course, the well-earned beer from AGLUP, the B...

Physical Layer Security Using Two-Path Successive Relaying

Directory of Open Access Journals (Sweden)

Qian Yu Liau

2016-06-01

Full Text Available Relaying is one of the useful techniques to enhance wireless physical-layer security. Existing literature shows that employing full-duplex relay instead of conventional half-duplex relay improves secrecy capacity and secrecy outage probability, but this is at the price of sophisticated implementation. As an alternative, two-path successive relaying has been proposed to emulate operation of full-duplex relay by scheduling a pair of half-duplex relays to assist the source transmission alternately. However, the performance of two-path successive relaying in secrecy communication remains unexplored. This paper proposes a secrecy two-path successive relaying protocol for a scenario with one source, one destination and two half-duplex relays. The relays operate alternately in a time division mode to forward messages continuously from source to destination in the presence of an eavesdropper. Analytical results reveal that the use of two half-duplex relays in the proposed scheme contributes towards a quadratically lower probability of interception compared to full-duplex relaying. Numerical simulations show that the proposed protocol achieves the ergodic achievable secrecy rate of full-duplex relaying while delivering the lowest probability of interception and secrecy outage probability compared to the existing half duplex relaying, full duplex relaying and full duplex jamming schemes.

Handover Framework for Relay Enhanced LTE Networks

DEFF Research Database (Denmark)

Teyeb, Oumer Mohammed; Van Phan, Vinh; Raaf, Bernhard

2009-01-01

Relaying is one of the proposed technologies for future releases of UTRAN Long Term Evolution (LTE) networks. Introducing relaying is expected to increase the coverage and capacity of LTE networks. In order to enable relaying, the architecture, protocol and radio resource management procedures...... of LTE, such as handover, have to be modified. A user can be handed over not only between two base stations, but also between relays and base stations, and between two relays. With the introduction of relaying, there is a need for a new procedure to hand over a relay and all its associated users...... to another base station, allowing a flexible and dynamic relay deployment. In this paper, we extend the LTE release 8 handover mechanisms so that it can accommodate these new handover functionalities in a flexible manner....

Optimal relay selection and power allocation for cognitive two-way relaying networks

KAUST Repository

Pandarakkottilil, Ubaidulla

2012-06-01

In this paper, we present an optimal scheme for power allocation and relay selection in a cognitive radio network where a pair of cognitive (or secondary) transceiver nodes communicate with each other assisted by a set of cognitive two-way relays. The secondary nodes share the spectrum with a licensed primary user (PU), and each node is assumed to be equipped with a single transmit/receive antenna. The interference to the PU resulting from the transmission from the cognitive nodes is kept below a specified limit. We propose joint relay selection and optimal power allocation among the secondary user (SU) nodes achieving maximum throughput under transmit power and PU interference constraints. A closed-form solution for optimal allocation of transmit power among the SU transceivers and the SU relay is presented. Furthermore, numerical simulations and comparisons are presented to illustrate the performance of the proposed scheme. © 2012 IEEE.

Relay Architectures for 3GPP LTE-Advanced

Directory of Open Access Journals (Sweden)

Peters StevenW

2009-01-01

Full Text Available The Third Generation Partnership Project's Long Term Evolution-Advanced is considering relaying for cost-effective throughput enhancement and coverage extension. While analog repeaters have been used to enhance coverage in commercial cellular networks, the use of more sophisticated fixed relays is relatively new. The main challenge faced by relay deployments in cellular systems is overcoming the extra interference added by the presence of relays. Most prior work on relaying does not consider interference, however. This paper analyzes the performance of several emerging half-duplex relay strategies in interference-limited cellular systems: one-way, two-way, and shared relays. The performance of each strategy as a function of location, sectoring, and frequency reuse are compared with localized base station coordination. One-way relaying is shown to provide modest gains over single-hop cellular networks in some regimes. Shared relaying is shown to approach the gains of local base station coordination at reduced complexity, while two-way relaying further reduces complexity but only works well when the relay is close to the handset. Frequency reuse of one, where each sector uses the same spectrum, is shown to have the highest network throughput. Simulations with realistic channel models provide performance comparisons that reveal the importance of interference mitigation in multihop cellular networks.

Determination of h2JNN and h1JHN coupling constants across Watson-Crick base pairs in the Antennapedia homeodomain-DNA complex using TROSY

International Nuclear Information System (INIS)

Pervushin, Konstantin; Fernandez, Cesar; Riek, Roland; Ono, Akira; Kainosho, Masatsune; Wuethrich, Kurt

2000-01-01

This paper describes NMR measurements of 15 N- 15 N and 1 H- 15 N scalar couplings across hydrogen bonds in Watson-Crick base pairs, h2 J NN and h1 J HN , in a 17 kDa Antennapedia homeodomain-DNA complex. A new NMR experiment is introduced which relies on zero-quantum coherence-based transverse relaxation-optimized spectroscopy (ZQ-TROSY) and enables measurements of h1 J HN couplings in larger molecules. The h2 J NN and h1 J HN couplings open a new avenue for comparative studies of DNA duplexes and other forms of nucleic acids free in solution and in complexes with proteins, drugs or possibly other classes of compounds

COSY Control Status. First results with rapid prototyped man-machine interface for accelerator control

Energy Technology Data Exchange (ETDEWEB)

Hacker, U [Forschungszentrum Juelich, Postfach 1913, 52425 Juelich (Germany); Haberbosch, C [Forschungszentrum Juelich, Postfach 1913, 52425 Juelich (Germany); Henn, K [Forschungszentrum Juelich, Postfach 1913, 52425 Juelich (Germany); Weinert, A [Forschungszentrum Juelich, Postfach 1913, 52425 Juelich (Germany)

1994-12-15

The experience gained with the COSY Control System after a six month commissioning period followed by a six month production period will be presented. The COSY Control System runs approximately 300 VME and VXI target systems using a total of about 1000 CPUs, the systems are driven by the diskless operating environment RT/OS, hosted by eight workcells. Application software is implemented using Object-Orientated programming paradigms. All accelerator components become interface functions as instances of an abstract device model class. Methods defined here present an abstract picture of the accelerator giving immediate access to device states and parameters. Operator interaction is defined by building views and controllers for the model. Higher level functions, such as defining an acceleration cycle, are easily developed and modified with the accelerator connected on-line to the model. In the first year of COSY operation the object based approach for a control system, together with a rapid prototyped man-machine interface has brought to light the potential of new functions such as on-line, real time programming on a running system yielding high programming performance. The advantages of this approach have not been, until now, fully appreciated. ((orig.))

Full-Duplex Relay Selection in Cognitive Underlay Networks

KAUST Repository

Khafagy, Mohammad Galal; Alouini, Mohamed-Slim; Aissa, Sonia

2017-01-01

In this work, we analyze the performance of full-duplex relay selection (FDRS) in spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay(s), thereby

Capacity gains of buffer-aided moving relays

KAUST Repository

Zafar, Ammar

2017-03-14

This work investigates the gain due to reduction in path loss by deploying buffer-aided moving relaying. In particular, the increase in gain due to moving relays is studied for dual-hop broadcast channels and the bidirectional relay channel. It is shown that the exploited gains in these channels due to buffer-aided relaying can be enhanced by utilizing the fact that a moving relay can communicate with the terminal closest to it and store the data in the buffer and then forward the data to the intended destination when it comes in close proximity with the destination. Numerical results show that for both the considered channels the achievable rates are increased as compared to the case of stationary relays. Numerical results also show that more significant increase in performance is seen when the relay moves to-and-fro between the source and the relay.

Capacity gains of buffer-aided moving relays

KAUST Repository

Zafar, Ammar; Shaqfeh, Mohammad; Alnuweiri, Hussein; Alouini, Mohamed-Slim

2017-01-01

This work investigates the gain due to reduction in path loss by deploying buffer-aided moving relaying. In particular, the increase in gain due to moving relays is studied for dual-hop broadcast channels and the bidirectional relay channel. It is shown that the exploited gains in these channels due to buffer-aided relaying can be enhanced by utilizing the fact that a moving relay can communicate with the terminal closest to it and store the data in the buffer and then forward the data to the intended destination when it comes in close proximity with the destination. Numerical results show that for both the considered channels the achievable rates are increased as compared to the case of stationary relays. Numerical results also show that more significant increase in performance is seen when the relay moves to-and-fro between the source and the relay.

Modified Dynamic Decode-and-Forward Relaying Protocol for Type II Relay in LTE-Advanced and Beyond.

Science.gov (United States)

Nam, Sung Sik; Alouini, Mohamed-Slim; Choi, Seyeong

2016-01-01

In this paper, we propose a modified dynamic decode-and-forward (MoDDF) relaying protocol to meet the critical requirements for user equipment (UE) relays in next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed MoDDF realizes the fast jump-in relaying and the sequential decoding with an application of random codeset to encoding and re-encoding process at the source and the multiple UE relays, respectively. A subframe-by-subframe decoding based on the accumulated (or buffered) messages is employed to achieve energy, information, or mixed combining. Finally, possible early termination of decoding at the end user can lead to the higher spectral efficiency and more energy saving by reducing the frequency of redundant subframe transmission and decoding. These attractive features eliminate the need of directly exchanging control messages between multiple UE relays and the end user, which is an important prerequisite for the practical UE relay deployment.

Performance analysis of opportunistic nonregenerative relaying

KAUST Repository

Tourki, Kamel; Alouini, Mohamed-Slim; Qaraqe, Khalid A.; Yang, Hongchuan

2013-01-01

Opportunistic relaying in cooperative communication depends on careful relay selection. However, the traditional centralized method used for opportunistic amplify-and-forward protocols requires precise measurements of channel state information at the destination. In this paper, we adopt the max-min criterion as a relay selection framework for opportunistic amplify-and-forward cooperative communications, which was exhaustively used for the decode-and-forward protocol, and offer an accurate performance analysis based on exact statistics of the local signal-to-noise ratios of the best relay. Furthermore, we evaluate the asymptotical performance and deduce the diversity order of our proposed scheme. Finally, we validate our analysis by showing that performance simulation results coincide with our analytical results over Rayleigh fading channels, and we compare the max-min relay selection with their centralized channel state information-based and partial relay selection counterparts.

Energy efficient circuit design using nanoelectromechanical relays

Science.gov (United States)

Venkatasubramanian, Ramakrishnan

Nano-electromechanical (NEM) relays are a promising class of emerging devices that offer zero off-state leakage and behave like an ideal switch. Recent advances in planar fabrication technology have demonstrated that microelectromechanical (MEMS) scale miniature relays could be manufactured reliably and could be used to build fully functional, complex integrated circuits. The zero leakage operation of relays has renewed the interest in relay based low power logic design. This dissertation explores circuit architectures using NEM relays and NEMS-CMOS heterogeneous integration. Novel circuit topologies for sequential logic, memory, and power management circuits have been proposed taking into consideration the NEM relay device properties and optimizing for energy efficiency and area. In nanoscale electromechanical devices, dispersion forces like Van der Waals' force (vdW) affect the pull-in stability of the relay devices significantly. Verilog-A electromechanical model of the suspended gate relay operating at 1V with a nominal air gap of 5 - 10nm has been developed taking into account all the electrical, mechanical and dispersion effects. This dissertation explores different relay based latch and flip-flop topologies. It has been shown that as few as 4 relay cells could be used to build flip-flops. An integrated voltage doubler based flip flop that improves the performance by 2X by overdriving Vgb has been proposed. Three NEM relay based parallel readout memory bitcell architectures have been proposed that have faster access time, and remove the reliability issues associated with previously reported serial readout architectures. A paradigm shift in design of power switches using NEM relays is proposed. An interesting property of the relay device is that the ON state resistance (Ron) of the NEM relay switch is constant and is insensitive to the gate slew rate. This coupled with infinite OFF state resistance (Roff ) offers significant area and power advantages over CMOS

78 FR 40407 - Structure and Practices of the Video Relay Service Program: Telecommunications Relay Services and...

Science.gov (United States)

2013-07-05

...] Structure and Practices of the Video Relay Service Program: Telecommunications Relay Services and Speech-to... telecommunications relay services (TRS) program continues to offer functional equivalence to all eligible users and..., identified by CG Docket Nos. 10-51 and 03-123, by any of the following methods: Electronic Filers: Comments...

pp Elastic Scattering: New Results from EDDA (COSY)

International Nuclear Information System (INIS)

Scobel, W.; EDDA Collaboration

2000-01-01

In the EDDA experiment excitation functions of proton--proton elastic scattering are studied with narrow steps in the projectile momentum range from 0.8 to 3.4 GeV/c and angular range 35 o ≤ Θ cm ≤ 90 o with a detector providing ΔΘ cm ∼ 1.4 o resolution and 85% solid angle coverage. Measurements are performed continuously during projectile acceleration on the Cooler Synchrotron COSY. In phase 1 of the experiment spin-averaged differential cross sections dσ/dOmega have been measured with an internal CH 2 fiber target; background corrections were derived from measurements with a carbon fiber target and from Monte Carlo simulations of inelastic pp contributions. The results provide excitation functions and angular distributions of high precision and internal consistency. In phase 2 of the experiment excitation functions of the analyzing power A N have been measured using a polarized (P≥75%) atomic beam target, and those of the polarization correlation parameters A NN , A SS and A SL will be measured later on with the polarized COSY beam. The measured excitation functions are compared to recent phase shift analyses, and their impact on them is discussed. So far evidence for narrow structures was neither found in the spin-averaged cross sections nor in the analyzing powers

pp Elastic Scattering: New Results from EDDA (COSY)

International Nuclear Information System (INIS)

Scobel, W.; EDDA Collaboration

2000-01-01

In the EDDA experiment excitation functions of proton - proton elastic scattering are studied with narrow steps in the projectile momentum range from 0.8 to 3.4 GeV/c and angular range 35 degree ≤ Θ cm ≤ 90 degree with a detector providing ΔΘ cm ∼ 1.4degree resolution and 85% solid angle coverage. Measurements are performed continuously during projectile acceleration on the Cooler Synchrotron COSY. In phase 1 of the experiment spin-averaged differential cross sections dσ/dΩ have been measured with an internal CH 2 fiber target; background corrections were derived from measurements with a carbon fiber target and from Monte Carlo simulations of inelastic pp contributions. The results provide excitation functions and angular distributions of high precision and internal consistency. In phase 2 of the experiment excitation functions of the analyzing power A N have been measured using a polarized (P≥75%) atomic beam target, and those of the polarization correlation parameters A NN , A SS and A SL will be measured later on with the polarized COSY beam. The measured excitation functions are compared to recent phase shift analyses, and their impact on them is discussed. So far evidence for narrow structures was neither found in the spin-averaged cross sections nor in the analyzing powers

pp Elastic Scattering: New results from EDDA (COSY)

International Nuclear Information System (INIS)

Scobel, W.

2000-01-01

In the EDDA experiment excitation functions of proton-proton elastic scattering are studied with narrow steps in the projectile momentum range from 0.8 to 3.4 GeV/c and the angular range 35 deg. ≤Θ cm ≤90 deg. with a detector providing ΔΘ cm ≅1.4 deg. resolution and 85% solid angle coverage. Measurements are performed continuously during projectile acceleration in the Cooler Synchrotron COSY. In phase 1 of the experiment spin-averaged differential cross sections dσ/dΩ have been measured with an internal CH 2 fiber target; background corrections were derived from measurements with a carbon fiber target and from Monte Carlo simulations of inelastic pp contributions. The results provide excitation functions and angular distributions of high precision and internal consistency. In phase 2 of the experiment excitation functions of the analyzing power A N have been measured using a polarized (P≥75%) atomic beam target, and those of the polarization correlation parameters A NN , A SS and A SL will be measured lateron with the polarized COSY beam. The measured excitation functions are compared to recent phase shift analyses, and their impact on them is discussed. So far evidence for narrow structures was neither found in the spin averaged cross sections nor in the analyzing powers

The Composite Strain Index (COSI) and Cumulative Strain Index (CUSI): methodologies for quantifying biomechanical stressors for complex tasks and job rotation using the Revised Strain Index.

Science.gov (United States)

Garg, Arun; Moore, J Steven; Kapellusch, Jay M

2017-08-01

The Composite Strain Index (COSI) quantifies biomechanical stressors for complex tasks consisting of exertions at different force levels and/or with different exertion times. The Cumulative Strain Index (CUSI) further integrates biomechanical stressors from different tasks to quantify exposure for the entire work shift. The paper provides methodologies to compute COSI and CUSI along with examples. Complex task simulation produced 169,214 distinct tasks. Use of average, time-weighted average (TWA) and peak force and COSI classified 66.9, 28.2, 100 and 38.9% of tasks as hazardous, respectively. For job rotation the simulation produced 10,920 distinct jobs. TWA COSI, peak task COSI and CUSI classified 36.5, 78.1 and 66.6% jobs as hazardous, respectively. The results suggest that the TWA approach systematically underestimates the biomechanical stressors and peak approach overestimates biomechanical stressors, both at the task and job level. It is believed that the COSI and CUSI partially address these underestimations and overestimations of biomechanical stressors. Practitioner Summary: COSI quantifies exposure when applied hand force and/or duration of that force changes during a task cycle. CUSI integrates physical exposures from job rotation. These should be valuable tools for designing and analysing tasks and job rotation to determine risk of musculoskeletal injuries.

Relay test program

International Nuclear Information System (INIS)

Bandyopadhyay, K.K.; Kunkel, C.; Shteyngart, S.

1994-02-01

This report presents the results of a relay test program conducted by Brookhaven National Laboratory (BNL) under the sponsorship of the US Nuclear Regulatory Commission (NRC). The program is a continuation of an earlier test program the results of which were published in NUREG/CR-4867. The current program was carried out in two phases: electrical testing and vibration testing. The objective was primarily to focus on the electrical discontinuity or continuity of relays and circuit breaker tripping mechanisms subjected to electrical pulses and vibration loads. The electrical testing was conducted by KEMA-Powertest Company and the vibration testing was performed at Wyle Laboratories, Huntsville, Alabama. This report discusses the test procedures, presents the test data, includes an analysis of the data and provides recommendations regarding reliable relay testing

Xenon-ion-induced and thermal mixing of Co/Si bilayers and their interplay

Science.gov (United States)

Novaković, M.; Zhang, K.; Popović, M.; Bibić, N.; Hofsäss, H.; Lieb, K. P.

2011-05-01

Studies on ion-irradiated transition-metal/silicon bilayers demonstrate that interface mixing and silicide phase formation depend sensitively on the ion and film parameters, including the structure of the metal/Si interface. Thin Co layers e-gun evaporated to a thickness of 50 nm on Si(1 0 0) wafers were bombarded at room temperature with 400-keV Xe + ions at fluences of up to 3 × 10 16 cm -2. We used either crystalline or pre-amorphized Si wafers the latter ones prepared by 1.0-keV Ar-ion implantation. The as-deposited or Xe-ion-irradiated samples were then isochronally annealed at temperatures up to 700 °C. Changes of the bilayer structures induced by ion irradiation and/or annealing were investigated with RBS, XRD and HRTEM. The mixing rate for the Co/c-Si couples, Δ σ2/ Φ = 3.0(4) nm 4, is higher than the value expected for ballistic mixing and about half the value typical for spike mixing. Mixing of pre-amorphized Si is much weaker relative to crystalline Si wafers, contrary to previous results obtained for Fe/Si bilayers. Annealing of irradiated samples produces very similar interdiffusion and phase formation patterns above 400 °C as in the non-irradiated Co/Si bilayers: the phase evolution follows the sequence Co 2Si → CoSi → CoSi 2.

Xenon-ion-induced and thermal mixing of Co/Si bilayers and their interplay

International Nuclear Information System (INIS)

Novakovic, M.; Zhang, K.; Popovic, M.; Bibic, N.; Hofsaess, H.; Lieb, K.P.

2011-01-01

Studies on ion-irradiated transition-metal/silicon bilayers demonstrate that interface mixing and silicide phase formation depend sensitively on the ion and film parameters, including the structure of the metal/Si interface. Thin Co layers e-gun evaporated to a thickness of 50 nm on Si(1 0 0) wafers were bombarded at room temperature with 400-keV Xe + ions at fluences of up to 3 x 10 16 cm -2 . We used either crystalline or pre-amorphized Si wafers the latter ones prepared by 1.0-keV Ar-ion implantation. The as-deposited or Xe-ion-irradiated samples were then isochronally annealed at temperatures up to 700 o C. Changes of the bilayer structures induced by ion irradiation and/or annealing were investigated with RBS, XRD and HRTEM. The mixing rate for the Co/c-Si couples, Δσ 2 /Φ = 3.0(4) nm 4 , is higher than the value expected for ballistic mixing and about half the value typical for spike mixing. Mixing of pre-amorphized Si is much weaker relative to crystalline Si wafers, contrary to previous results obtained for Fe/Si bilayers. Annealing of irradiated samples produces very similar interdiffusion and phase formation patterns above 400 o C as in the non-irradiated Co/Si bilayers: the phase evolution follows the sequence Co 2 Si → CoSi → CoSi 2 .

CERN Relay Race

CERN Document Server

2006-01-01

The CERN relay race will take place around the Meyrin site on Wednesday 17 May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Details on how to register your team for the relay race are given on the Staff Association Bulletin web site.

Energy-efficient relay selection and optimal power allocation for performance-constrained dual-hop variable-gain AF relaying

KAUST Repository

Zafar, Ammar

2013-12-01

This paper investigates the energy-efficiency enhancement of a variable-gain dual-hop amplify-and-forward (AF) relay network utilizing selective relaying. The objective is to minimize the total consumed power while keeping the end-to-end signal-to-noise-ratio (SNR) above a certain peak value and satisfying the peak power constraints at the source and relay nodes. To achieve this objective, an optimal relay selection and power allocation strategy is derived by solving the power minimization problem. Numerical results show that the derived optimal strategy enhances the energy-efficiency as compared to a benchmark scheme in which both the source and the selected relay transmit at peak power. © 2013 IEEE.

SWIPT in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

KAUST Repository

Benkhelifa, Fatma

2017-02-09

In this paper, we consider a multiuser multiple- input multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting relays and multiple destinations. Since the end-to-end sum rate maximization problem is intractable, we tackle a simplified problem where we maximize the sum of the harvested energy at the relays, we employ the block diagonalization (BD) procedure at the source, and we mitigate the interference between the relay- destination channels. The interference mitigation at the destinations is managed in two ways: either to fix the interference covariance matrices at the destination and update them at each iteration until convergence, or to cancel the interference using an algorithm similar to the BD method. We provide numerical results to show the relevance of our proposed solution.

Relaying Strategies and Protocols for Efficient Wireless Networks

KAUST Repository

Zafar, Ammar

2014-10-01

Next generation wireless networks are expected to provide high data rate and satisfy the Quality-of-Service (QoS) constraints of the users. A significant component of achieving these goals is to increase the effi ciency of wireless networks by either optimizing current architectures or exploring new technologies which achieve that. The latter includes revisiting technologies which were previously proposed, but due to a multitude of reasons were ignored at that time. One such technology is relaying which was initially proposed in the latter half of the 1960s and then was revived in the early 2000s. In this dissertation, we study relaying in conjunction with resource allocation to increase the effi ciency of wireless networks. In this regard, we differentiate between conventional relaying and relaying with buffers. Conventional relaying is traditional relaying where the relay forwards the signal it received immediately. On the other hand, in relaying with buffers or buffer-aided relaying as it is called, the relay can store received data in its buffer and forward it later on. This gives the benefit of taking advantage of good channel conditions as the relay can only transmit when the channel conditions are good. The dissertation starts with conventional relaying and considers the problem of minimizing the total consumed power while maintaining system QoS. After upper bounding the system performance, more practical algorithms which require reduced feedback overhead are explored. Buffer-aided relaying is then considered and the joint user-and-hop scheduler is introduced which exploits multi-user diversity (MUD) and 5 multi-hop diversity (MHD) gains together in dual-hop broadcast channels. Next joint user-and-hop scheduling is extended to the shared relay channel where two source-destination pairs share a single relay. The benefits of buffer-aided relaying in the bidirectional relay channel utilizing network coding are then explored. Finally, a new transmission protocol

Spoiled Onions: Exposing Malicious Tor Exit Relays

OpenAIRE

Winter, Philipp; Lindskog, Stefan

2014-01-01

Several hundred Tor exit relays together push more than 1 GiB/s of network traffic. However, it is easy for exit relays to snoop and tamper with anonymised network traffic and as all relays are run by independent volunteers, not all of them are innocuous. In this paper, we seek to expose malicious exit relays and document their actions. First, we monitored the Tor network after developing a fast and modular exit relay scanner. We implemented several scanning modules for detecting common attac...

Computational aspects of optics design and simulation: COSY INFINITY

International Nuclear Information System (INIS)

Berz, M.; National Superconducting Cyclotron Lab., East Lansing, MI; Lawrence Berkeley Lab., CA

1990-01-01

The new differential algebraic (DA) techniques allow very efficient treatment and understanding of nonlinear motion in optical systems aws well as circular accelerators. To utilize these techniques in their most general way, a powerful software environment is essential. A language with structure elements similar to Pascal was developed. It has object oriented features to allow for a direct utilization of the elementary operations of the DA package. The compiler of the language is written in Fortran 77 to guarantee wide portability. The language was used to write a very general beam optics code, COSY INFINITY. At its lowest level, it allows the computation of the maps of standard beam line elements including fringe fields and system parameters to arbitrary order. the power of the DA approach coupled with an adequate language environment reveals itself in the very limited lenth of COSY INFINITY of only a few hundred lines. Grouping of elements as well as structures for optimization and study are readily available through the features of the language. Because of the openness of the approach, it offers a lot of power for more advanced purposes. For example, it is very easy to construct new particle optical elements. There are many ways to efficiently manipulate and analyze the maps. (orig.)

SWIPT in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

KAUST Repository

Benkhelifa, Fatma; Salem, Ahmed Sultan; Alouini, Mohamed-Slim

2017-01-01

In this paper, we consider a multiuser multiple- input multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting relays and multiple destinations. Since the end-to-end sum rate

Control circuit for transformer relay

International Nuclear Information System (INIS)

Wyatt, G.A.

1984-01-01

A control circuit for a transformer relay which will automatically momentarily control the transformer relay to a selected state upon energization of the control circuit. The control circuit has an energy storage element and a current director coupled in series and adapted to be coupled with the secondary winding of the transformer relay. A device for discharge is coupled across the energy storage element. The energy storage element and current director will momentarily allow a unidirectional flow of current in the secondary winding of the transformer relay upon application of energy to the control circuit. When energy is not applied to the control circuit the device for discharge will allow the energy storage element to discharge and be available for another operation of the control circuit

Improper Signaling for Virtual Full-Duplex Relay Systems

KAUST Repository

Gaafar, Mohamed; Amin, Osama; Schaefer, Rafael F.; Alouini, Mohamed-Slim

2017-01-01

Virtual full-duplex (VFD) is a powerful solution to compensate the rate loss of half-duplex relaying without the need to full-duplex capable nodes. Inter-relay interference (IRI) challenges the operation of VFD relaying systems. Recently, improper signaling is employed at both relays of the VFD to mitigate the IRI by imposing the same signal characteristics for both relays. To further boost the achievable rate performance, asymmetric time sharing VFD relaying system is adopted with different improper signals at the half-duplex relays. The joint tuning of the three design parameters improves the achievable rate performance at different ranges of IRI and different relays locations. Extensive simulation results are presented and analyzed to show the achievable rate gain of the proposed system and understand the system behavior.

Improper Signaling for Virtual Full-Duplex Relay Systems

KAUST Repository

Gaafar, Mohamed

2017-02-14

Virtual full-duplex (VFD) is a powerful solution to compensate the rate loss of half-duplex relaying without the need to full-duplex capable nodes. Inter-relay interference (IRI) challenges the operation of VFD relaying systems. Recently, improper signaling is employed at both relays of the VFD to mitigate the IRI by imposing the same signal characteristics for both relays. To further boost the achievable rate performance, asymmetric time sharing VFD relaying system is adopted with different improper signals at the half-duplex relays. The joint tuning of the three design parameters improves the achievable rate performance at different ranges of IRI and different relays locations. Extensive simulation results are presented and analyzed to show the achievable rate gain of the proposed system and understand the system behavior.

Speech-to-Speech Relay Service

Science.gov (United States)

Consumer Guide Speech to Speech Relay Service Speech-to-Speech (STS) is one form of Telecommunications Relay Service (TRS). TRS is a service that allows persons with hearing and speech disabilities ...

Outage performance of two-way DF relaying systems with a new relay selection metric

KAUST Repository

Hyadi, Amal

2012-04-01

This paper investigates a new constrained relay selection scheme for two-way relaying systems where two end terminals communicate simultaneously via a relay. The introduced technique is based on the maximization of the weighted sum rate of both users. To evaluate the performance of the proposed system, the outage probability is derived in a general case (where an arbitrary channel is considered), and then over independently but not necessarily identically distributed (i.n.i.d.) Rayleigh fading channels. The analytical results are verified through simulations. © 2012 IEEE.

Modified Dynamic Decode-and-Forward Relaying Protocol for Type II Relay in LTE-Advanced and Beyond

KAUST Repository

Nam, Sung Sik; Alouini, Mohamed-Slim; Choi, Seyeong

2016-01-01

In this paper, we propose a modified dynamic decode-and-forward (MoDDF) relaying protocol to meet the critical requirements for user equipment (UE) relays in next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed MoDDF realizes the fast jump-in relaying and the sequential decoding with an application of random codeset to encoding and re-encoding process at the source and the multiple UE relays, respectively. A subframe-by-subframe decoding based on the accumulated (or buffered) messages is employed to achieve energy, information, or mixed combining. Finally, possible early termination of decoding at the end user can lead to the higher spectral efficiency and more energy saving by reducing the frequency of redundant subframe transmission and decoding. These attractive features eliminate the need of directly exchanging control messages between multiple UE relays and the end user, which is an important prerequisite for the practical UE relay deployment. Copyright: © 2016 Nam et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

Modified Dynamic Decode-and-Forward Relaying Protocol for Type II Relay in LTE-Advanced and Beyond

KAUST Repository

Nam, Sung Sik

2016-11-29

In this paper, we propose a modified dynamic decode-and-forward (MoDDF) relaying protocol to meet the critical requirements for user equipment (UE) relays in next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed MoDDF realizes the fast jump-in relaying and the sequential decoding with an application of random codeset to encoding and re-encoding process at the source and the multiple UE relays, respectively. A subframe-by-subframe decoding based on the accumulated (or buffered) messages is employed to achieve energy, information, or mixed combining. Finally, possible early termination of decoding at the end user can lead to the higher spectral efficiency and more energy saving by reducing the frequency of redundant subframe transmission and decoding. These attractive features eliminate the need of directly exchanging control messages between multiple UE relays and the end user, which is an important prerequisite for the practical UE relay deployment. Copyright: © 2016 Nam et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

Improper signaling in two-path relay channels

KAUST Repository

Gaafar, Mohamed

2017-07-03

Inter-relay interference (IRI) challenges the operation of two-path relaying systems. Furthermore, the unavailability of the channel state information (CSI) at the source and the limited detection capabilities at the relays prevent neither eliminating the interference nor adopting joint detection at the relays nodes. Improper signaling is a powerful signaling scheme that has the capability to reduce the interference impact at the receiver side and improves the achievable rate performance. Therefore, improper signaling is adopted at both relays, which have access to the global CSI. Then, improper signal characteristics are designed to maximize the total end-to-end achievable rate at the relays. To this end, both the power and the circularity coefficient, a measure of the impropriety degree of the signal, are optimized at the relays. Although the optimization problem is not convex, optimal power allocation for both relays for a fixed circularity coefficient is obtained. Moreover, the circularity coefficient is tuned to maximize the rate for a given power allocation. Finally, a joint solution of the optimization problem is proposed using a coordinate descent method based on alternate optimization. The simulation results show that employing improper signaling improves the achievable rate at medium and high IRI.

Improper signaling in two-path relay channels

KAUST Repository

Gaafar, Mohamed; Amin, Osama; Schaefer, Rafael F.; Alouini, Mohamed-Slim

2017-01-01

Inter-relay interference (IRI) challenges the operation of two-path relaying systems. Furthermore, the unavailability of the channel state information (CSI) at the source and the limited detection capabilities at the relays prevent neither eliminating the interference nor adopting joint detection at the relays nodes. Improper signaling is a powerful signaling scheme that has the capability to reduce the interference impact at the receiver side and improves the achievable rate performance. Therefore, improper signaling is adopted at both relays, which have access to the global CSI. Then, improper signal characteristics are designed to maximize the total end-to-end achievable rate at the relays. To this end, both the power and the circularity coefficient, a measure of the impropriety degree of the signal, are optimized at the relays. Although the optimization problem is not convex, optimal power allocation for both relays for a fixed circularity coefficient is obtained. Moreover, the circularity coefficient is tuned to maximize the rate for a given power allocation. Finally, a joint solution of the optimization problem is proposed using a coordinate descent method based on alternate optimization. The simulation results show that employing improper signaling improves the achievable rate at medium and high IRI.

Relay self interference minimisation using tapped filter

KAUST Repository

Jazzar, Saleh

2013-05-01

In this paper we introduce a self interference (SI) estimation and minimisation technique for amplify and forward relays. Relays are used to help forward signals between a transmitter and a receiver. This helps increase the signal coverage and reduce the required transmitted signal power. One problem that faces relays communications is the leaked signal from the relay\\'s output to its input. This will cause an SI problem where the new received signal at the relay\\'s input will be added with the unwanted leaked signal from the relay\\'s output. A Solution is proposed in this paper to estimate and minimise this SI which is based upon using a tapped filter at the destination. To get the optimum weights for this tapped filter, some channel parameters must be estimated first. This is performed blindly at the destination without the need of any training. This channel parameter estimation method is named the blind-self-interference-channel-estimation (BSICE) method. The next step in the proposed solution is to estimate the tapped filter\\'s weights. This is performed by minimising the mean squared error (MSE) at the destination. This proposed method is named the MSE-Optimum Weight (MSE-OW) method. Simulation results are provided in this paper to verify the performance of BSICE and MSE-OW methods. © 2013 IEEE.

Dynamic Relaying in 3GPP LTE-Advanced Networks

DEFF Research Database (Denmark)

Teyeb, Oumer Mohammed; Van Phan, Vinh; Redana, Simone

2009-01-01

Relaying is one of the proposed technologies for LTE-Advanced networks. In order to enable a flexible and reliable relaying support, the currently adopted architectural structure of LTE networks has to be modified. In this paper, we extend the LTE architecture to enable dynamic relaying, while...... maintaining backward compatibility with LTE Release 8 user equipments, and without limiting the flexibility and reliability expected from relaying.With dynamic relaying, relays can be associated with base stations on a need basis rather than in a fixed manner which is based only on initial radio planning....... Proposals are also given on how to further improve a relay enhanced LTE network by enabling multiple interfaces between the relay nodes and their controlling base stations, which can possibly be based on technologies different from LTE, so that load balancing can be realized. This load balancing can...

Performance limitations of relay neurons.

Directory of Open Access Journals (Sweden)

Rahul Agarwal

Full Text Available Relay cells are prevalent throughout sensory systems and receive two types of inputs: driving and modulating. The driving input contains receptive field properties that must be transmitted while the modulating input alters the specifics of transmission. For example, the visual thalamus contains relay neurons that receive driving inputs from the retina that encode a visual image, and modulating inputs from reticular activating system and layer 6 of visual cortex that control what aspects of the image will be relayed back to visual cortex for perception. What gets relayed depends on several factors such as attentional demands and a subject's goals. In this paper, we analyze a biophysical based model of a relay cell and use systems theoretic tools to construct analytic bounds on how well the cell transmits a driving input as a function of the neuron's electrophysiological properties, the modulating input, and the driving signal parameters. We assume that the modulating input belongs to a class of sinusoidal signals and that the driving input is an irregular train of pulses with inter-pulse intervals obeying an exponential distribution. Our analysis applies to any [Formula: see text] order model as long as the neuron does not spike without a driving input pulse and exhibits a refractory period. Our bounds on relay reliability contain performance obtained through simulation of a second and third order model, and suggest, for instance, that if the frequency of the modulating input increases or the DC offset decreases, then relay increases. Our analysis also shows, for the first time, how the biophysical properties of the neuron (e.g. ion channel dynamics define the oscillatory patterns needed in the modulating input for appropriately timed relay of sensory information. In our discussion, we describe how our bounds predict experimentally observed neural activity in the basal ganglia in (i health, (ii in Parkinson's disease (PD, and (iii in PD during

Modular relay control

OpenAIRE

Ivarsson, Mikael

2010-01-01

Enics Sweden AB, Västerås, is an electronics manufacturing services company with its main business in manufacturing electronics. Most, if not all, electronic devices that are manufactured are being widely tested before delivery to ensure proper functionality. Often during tests a large number of signals are measured by one to a few digital multimeters and are therefore controlled through relays. Relays are also used when applying stimuli with high currents or voltages to the unit under test. ...

Nucleon-nucleon scattering studies at small angles at COSY-ANKE

Energy Technology Data Exchange (ETDEWEB)

Bagdasarian, Zara [Forschungszentrum Juelich, Juelich (Germany); Tbilisi State University, Tbilisi (Georgia); Collaboration: ANKE-Collaboration

2015-07-01

The most accepted approach to describe nucleon-nucleon (NN) interaction is the partial wave analysis (PWA). The SAID database and analysis program comprise various experimental observables at different energies over the full angular range and express them in the partial waves. The goal of the experiments held at COSY-Juelich is to provide SAID with new valuable measurements. Scattering data was taken at small angles for six beam energies between 0.8 and 2.4 GeV with polarized proton beam incident on both proton and deuteron unpolarized targets using the ANKE spectrometer. First, the results of the proton-proton (pp) scattering analyzing power and cross section are presented. While pp data closes a very important gap at small angles in the database, proton-neutron (pn) data is a crucial contribution to the almost non-explored pn database above 800 MeV. Therefore, the talk will mainly concentrate on the proton-deuteron (pd) scattering studies, which includes the overview of the older COSY experiments with polarized deuteron beam, and the abovementioned new experiment with polarized proton beam and unpolarized deuteron target. The presentation will show the most recent results of the analyzing powers of pd elastic and pn scattering.

On the achievable degrees of freedom of alternate MIMO relaying with multiple AF relays

KAUST Repository

Park, Kihong; Alouini, Mohamed-Slim; Park, Seongho; Ko, Youngchai

2012-01-01

In this paper, we consider a two-hop relaying network where one source, one destination, and multiple amplify-and-forward (AF) relays equipped with M antennas operate in a half-duplex mode. In order to compensate for the inherent loss of capacity

2D COSY sup 1 H NMR; A new tool for studying in sity brain metabolism in the living animal

Energy Technology Data Exchange (ETDEWEB)

Barrere, B.; Peres, M.; Seulaz, J. (Universite Paris 7 (France). Laboratoire de Physiologie et Physiopathologie Cerebrovasculaire INSERM U 182 CNRS UA 641, Paris (France)); Gillet, B.; Mergui, S.; Beloeil, J.-C. (Centre National de la Recherche Scientifique, 91 - Gif-sur-Yvette (France). Inst. de Chimie des Substances Naturelles)

1990-05-21

2D COSY {sup 1}H NMR with surface coil has been used to resolve and assign cerebral metabolites which had previously been detected but could not be resolved or assigned in situ in the living animal by conventional 1D {sup 1}H NMR. A wide range of cerebral metabolites, including alanine, N-acetyl asparate, asparate, choline derivatives, creatine/phosphocreatine pool, GABA, glucose, glutamate/glutamine pool, inositol, lactate and taurine were simultaneously resolved and assigned in situ in the whole animal using the 2D COSY correlation graphs. Global irreversible ischemia caused the appearance and the disappearance of cross-peaks in the 2D COSY {sup 1}H NMR map, corresponding to increases in alanine, GABA and lactate and glucose depletion. (author). 21 refs.; 3 figs.

Iterative Relay Scheduling with Hybrid ARQ under Multiple User Equipment (Type II) Relay Environments

KAUST Repository

Nam, Sung Sik; Alouini, Mohamed-Slim; Choi, Seyeong

2018-01-01

-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed IRS-HARQ aims to increase the achievable data rate by iteratively scheduling a relatively better UE relay closer to the end user in a probabilistic sense, provided that the relay-to-end user

The effect of noncollinearity of 15N-1H dipolar and 15N CSA tensors and rotational anisotropy on 15N relaxation, CSA/dipolar cross correlation, and TROSY

International Nuclear Information System (INIS)

Fushman, David; Cowburn, David

1999-01-01

Current approaches to 15N relaxation in proteins assume that the 15N-1H dipolar and 15N CSA tensors are collinear. We show theoretically that, when there is significant anisotropy of molecular rotation, different orientations of the two tensors, experimentally observed in proteins, nucleic acids, and small peptides, will result in differences in site- specific correlation functions and spectral densities. The standard treatments of the rates of longitudinal and transverse relaxation of amide 15N nuclei, of the 15N CSA/15N-1H dipolar cross correlation, and of the TROSY experiment are extended to account for the effect of noncollinearity of the 15N-1H dipolar and 15N CSA (chemical shift anisotropy) tensors. This effect, proportional to the degree of anisotropy of the overall motion, (D-parallel /D-perpendicular -1), is sensitive to the relative orientation of the two tensors and to the orientation of the peptide plane with respect to the diffusion coordinate frame. The effect is negligible at small degrees of anisotropy, but is predicted to become significant for D-parallel /D-perpendicular ≥1.5, and at high magnetic fields. The effect of noncollinearity of 15N CSA and 15N-1H dipolar interaction is sensitive to both gross (hydrodynamic) properties and atomic-level details of protein structure. Incorporation of this effect into relaxation data analysis is likely to improve both precision and accuracy of the derived characteristics of protein dynamics, especially at high magnetic fields and for molecules with a high degree of anisotropy of the overall motion. The effect will also make TROSY efficiency dependent on local orientation in moderately anisotropic systems

Status of the EDDA experiment at COSY

Science.gov (United States)

Scobel, W.; EDDA Collaboration; Bisplinghoff, J.; Bollmann, R.; Cloth, P.; Dohrmann, F.; Dorner, G.; Drüke, V.; Ernst, J.; Eversheim, P. D.; Filges, D.; Gasthuber, M.; Gebel, R.; Groß, A.; Groß-Hardt, R.; Hinterberger, F.; Jahn, R.; Lahr, U.; Langkau, R.; Lippert, G.; Mayer-Kuckuk, T.; Maschuw, R.; Mertler, G.; Metsch, B.; Mosel, F.; Paetz gen Schieck, H.; Petry, H. R.; Prasuhn, D.; von Przewoski, B.; Rohdjeß, H.; Rosendaal, D.; von Rossen, P.; Scheid, H.; Schirm, N.; Schwandt, F.; Stein, H.; Theis, D.; Weber, J.; Wiedmann, W.; Woller, K.; Ziegler, R.

1993-07-01

The EDDA experiment is designed to study p + p excitation functions with high energy resolution and narrow step size in the kinetic energy range from 250 MeV to 2500 MeV at the Cooler Synchrotron COSY. Measurements during the accelertion phase in conjunction with internal targets will allow to achieve a fast and precise energy variation. Prototypes of the detector elements and the fiber target have been extensively tested with proton and electron beams; the detector performance and trigger efficiency have been studied in Monte Carlo simulations. In this contribution, results concerning detector design, prototype studies, Monte Carlo simulations and the anticipated detector resolutions will be reported.

Status of the EDDA experiment at COSY

International Nuclear Information System (INIS)

Scobel, W.; Bisplinghoff, J.; Bollmann, R.; Cloth, P.; Dohrmann, F.; Dorner, G.; Drueke, V.; Ernst, J.; Eversheim, P.D.; Filges, D.; Gasthuber, M.; Gebel, R.; Gross, A.; Gross-Hardt, R.; Hinterberger, F.; Jahn, R.; Lahr, U.; Langkau, R.; Lippert, G.; Mayer-Kuckuk, T.; Maschuw, R.; Mertler, G.; Metsch, B.; Mosel, F.; Paetz genannt Schieck, H.; Petry, H.R.; Prasuhn, D.; Przewoski, B. von; Rohdjess, H.; Rosendaal, D.; Rossen, P. von; Scheid, H.; Schirm, N.; Schwandt, F.; Scobel, W.; Stein, H.; Theis, D.; Weber, J.; Wiedmann, W.; Woller, K.; Ziegler, R.

1993-01-01

The EDDA experiment is designed to study p+p excitation functions with high energy resolution and narrow step size in the kinetic energy range from 250 MeV to 2500 MeV at the Cooler Synchrotron COSY. Measurements during the acceleration phase in conjuntion with internal targets will allow to achieve a fast and precise energy variation. Prototypes of the detector elements and the fiber target have been exentsively tested with proton and electron beams; the detector performance and trigger efficiency have been studied in Monte Carlo simulations. In this contribution, results concerning detector design, prototype studies, Monte Carlo simulations and the anticipated detector resolutions will be reported. (orig.)

Multiple relay selection for delay-limited applications

KAUST Repository

Alsharoa, Ahmad M.

2013-12-01

A multiple relay selection system model that implements the decode-and-forward mode is investigated. All communication nodes are assumed to be equipped by multiple antennas. Furthermore, lattices space-time coded multiple-input multiple-output half duplex channel is applied. The main goal is to increase the throughput of the system by selecting multiple number of relays. The selection criteria depends on the maximum decoding delay at relays where the system implements a decoding time-out algorithm at each relay. This leads to a significant saving in the overall system power consumptions and attempts to solve the relays synchronization problem. All results are presented using numerical simulations. © 2012 IEEE.

Dynamic Relaying in 3GPP LTE-Advanced Networks

Directory of Open Access Journals (Sweden)

Van Phan Vinh

2009-01-01

Full Text Available Relaying is one of the proposed technologies for LTE-Advanced networks. In order to enable a flexible and reliable relaying support, the currently adopted architectural structure of LTE networks has to be modified. In this paper, we extend the LTE architecture to enable dynamic relaying, while maintaining backward compatibility with LTE Release 8 user equipments, and without limiting the flexibility and reliability expected from relaying. With dynamic relaying, relays can be associated with base stations on a need basis rather than in a fixed manner which is based only on initial radio planning. Proposals are also given on how to further improve a relay enhanced LTE network by enabling multiple interfaces between the relay nodes and their controlling base stations, which can possibly be based on technologies different from LTE, so that load balancing can be realized. This load balancing can be either between different base stations or even between different networks.

Airborne relay-based regional positioning system.

Science.gov (United States)

Lee, Kyuman; Noh, Hongjun; Lim, Jaesung

2015-05-28

Ground-based pseudolite systems have some limitations, such as low vertical accuracy, multipath effects and near-far problems. These problems are not significant in airborne-based pseudolite systems. However, the monitoring of pseudolite positions is required because of the mobility of the platforms on which the pseudolites are mounted, and this causes performance degradation. To address these pseudolite system limitations, we propose an airborne relay-based regional positioning system that consists of a master station, reference stations, airborne relays and a user. In the proposed system, navigation signals are generated from the reference stations located on the ground and are relayed via the airborne relays. Unlike in conventional airborne-based systems, the user in the proposed system sequentially estimates both the locations of airborne relays and his/her own position. Therefore, a delay due to monitoring does not occur, and the accuracy is not affected by the movement of airborne relays. We conducted several simulations to evaluate the performance of the proposed system. Based on the simulation results, we demonstrated that the proposed system guarantees a higher accuracy than airborne-based pseudolite systems, and it is feasible despite the existence of clock offsets among reference stations.

Bilayer expurgated LDPC codes with uncoded relaying

Directory of Open Access Journals (Sweden)

Md. Noor-A-Rahim

2017-08-01

Full Text Available Bilayer low-density parity-check (LDPC codes are an effective coding technique for decode-and-forward relaying, where the relay forwards extra parity bits to help the destination to decode the source bits correctly. In the existing bilayer coding scheme, these parity bits are protected by an error correcting code and assumed reliably available at the receiver. We propose an uncoded relaying scheme, where the extra parity bits are forwarded to the destination without any protection. Through density evolution analysis and simulation results, we show that our proposed scheme achieves better performance in terms of bit erasure probability than the existing relaying scheme. In addition, our proposed scheme results in lower complexity at the relay.

A SDP based design of relay precoding for the power minimization of MIMO AF-relay networks

KAUST Repository

Rao, Anlei

2015-09-11

Relay precoding for multiple-input and multiple-output (MIMO) relay networks has been approached by either optimizing the efficiency performance with given power consumption constraints or minimizing the power consumption with quality-of-service (QoS) requirements. For the later type design, previous works has worked on minimizing the approximated power consumption. In this paper, exact power consumption for all relays is derived into a quadratic form by diagonalizing the minimum-square error (MSE) matrix, and the relay precoding matrix is designed by optimizing this quadratic form with the help of semidefinite programming (SDP) relaxation. Our simulation results show that such a design can achieve a gain of around 3 dB against the previous design, which optimized the approximated power consumption. © 2015 IEEE.

Opportunistic Relay Selection with Cooperative Macro Diversity

Directory of Open Access Journals (Sweden)

Yu Chia-Hao

2010-01-01

Full Text Available We apply a fully opportunistic relay selection scheme to study cooperative diversity in a semianalytical manner. In our framework, idle Mobile Stations (MSs are capable of being used as Relay Stations (RSs and no relaying is required if the direct path is strong. Our relay selection scheme is fully selection based: either the direct path or one of the relaying paths is selected. Macro diversity, which is often ignored in analytical works, is taken into account together with micro diversity by using a complete channel model that includes both shadow fading and fast fading effects. The stochastic geometry of the network is taken into account by having a random number of randomly located MSs. The outage probability analysis of the selection differs from the case where only fast fading is considered. Under our framework, distribution of the received power is formulated using different Channel State Information (CSI assumptions to simulate both optimistic and practical environments. The results show that the relay selection gain can be significant given a suitable amount of candidate RSs. Also, while relay selection according to incomplete CSI is diversity suboptimal compared to relay selection based on full CSI, the loss in average throughput is not too significant. This is a consequence of the dominance of geometry over fast fading.

Opportunistic Fixed Gain Bidirectional Relaying with Outdated CSI

KAUST Repository

Khan, Fahd Ahmed; Tourki, Kamel; Alouini, Mohamed-Slim; Qaraqe, Khalid A.

2015-01-01

In a network with multiple relays, relay selection has been shown as an effective scheme to achieve diversity as well as to improve the overall throughput. This paper studies the impact of using outdated channel state information for relay selection on the performance of a network where two sources communicate with each other via fixed-gain amplify-and-forward relays. For a Rayleigh faded channel, closed-form expressions for the outage probability, moment generating function and symbol error rate are derived. Simulations results are also presented to corroborate the derived analytical results. It is shown that adding relays does not improve the performance if the channel is substantially outdated. Furthermore, relay location is also taken into consideration and it is shown that the performance can be improved by placing the relay closer to the source whose channel is more outdated. © 2015 IEEE.

Opportunistic Fixed Gain Bidirectional Relaying with Outdated CSI

KAUST Repository

Khan, Fahd Ahmed

2015-05-01

In a network with multiple relays, relay selection has been shown as an effective scheme to achieve diversity as well as to improve the overall throughput. This paper studies the impact of using outdated channel state information for relay selection on the performance of a network where two sources communicate with each other via fixed-gain amplify-and-forward relays. For a Rayleigh faded channel, closed-form expressions for the outage probability, moment generating function and symbol error rate are derived. Simulations results are also presented to corroborate the derived analytical results. It is shown that adding relays does not improve the performance if the channel is substantially outdated. Furthermore, relay location is also taken into consideration and it is shown that the performance can be improved by placing the relay closer to the source whose channel is more outdated. © 2015 IEEE.

MaROS Strategic Relay Planning and Coordination Interfaces

Science.gov (United States)

Allard, Daniel A.

2010-01-01

The Mars Relay Operations Service (MaROS) is designed to provide planning and analysis tools in support of ongoing Mars Network relay operations. Strategic relay planning requires coordination between lander and orbiter mission ground data system (GDS) teams to schedule and execute relay communications passes. MaROS centralizes this process, correlating all data relevant to relay coordination to provide a cohesive picture of the relay state. Service users interact with the system through thin-layer command line and web user interface client applications. Users provide and utilize data such as lander view periods of orbiters, Deep Space Network (DSN) antenna tracks, and reports of relay pass performance. Users upload and download relevant relay data via formally defined and documented file structures including some described in Extensible Markup Language (XML). Clients interface with the system via an http-based Representational State Transfer (ReST) pattern using Javascript Object Notation (JSON) formats. This paper will provide a general overview of the service architecture and detail the software interfaces and considerations for interface design.

Relay selection from an effective capacity perspective

KAUST Repository

Yang, Yuli

2013-09-01

In this work, we consider a cooperative network where multiple relay nodes having different modulation capabilities assist the end-to-end communication between a source and its destination. Firstly, we evaluate the effective capacity (EC) performance of the network under study. According to the analysis, an EC-based relay selection criterion is proposed. Based on the proposed selection rule and half-duplex decode-and-forward protocol, the activated relays cooperatively help with the packet transmission from the source. At the destination, packet combining is taken into account to improve the quality of service. Compared to the popular scheme, opportunistic relay selection, numerical results are provided to prove the validity and advantages of our proposed scheme in certain scenarios. Moreover, the analysis presented herein offers a convenient tool to the relaying transmission design, specifically on which relay selection scheme should be used as well as how to choose the receiving strategy between with and without packet combining at the destination. © 2013 IEEE.

CERN Relay Race 2009

CERN Document Server

2009-01-01

The CERN relay race will take place around the Meyrin site on Thursday 14th May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. More details on how to register your team for the relay race

Reversal thyristor-relay direct current commutator

International Nuclear Information System (INIS)

Ivanenko, A.I.

1982-01-01

A thyristor-relay commutator used for alteration of the leading magnetic field direction in experiments with polarized neutrons is described. The commutator flowsheet is presented. Thyristors, connected so as to allow the relay trigger operation mode, are used as controllable electronic relay. Two connected in series coils with the total inductance of the order of 0.28 H serve as the electronic relay load. The arc-free current commutation is effected at the moment of the minimal current across the load terminals, which allows to easily reverse the current up to 10 A at a volatage, v <= 150 V. The experience gained within a year of operation has shown that the commutator meets the requirements of reliability and tuning

CERN Relay Race

CERN Multimedia

2011-01-01

The CERN relay race will take place around the Meyrin site on Thursday 19 May starting at 12-15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details of the course and of how to register your team for the relay race can be found here. Some advice for all runners from the Medical Service can also be found here.   

A low complexity algorithm for multiple relay selection in two-way relaying Cognitive Radio networks

KAUST Repository

Alsharoa, Ahmad M.

2013-06-01

In this paper, a multiple relay selection scheme for two-way relaying cognitive radio network is investigated. We consider a cooperative Cognitive Radio (CR) system with spectrum sharing scenario using Amplify-and-Forward (AF) protocol, where licensed users and unlicensed users operate on the same frequency band. The main objective is to maximize the sum rate of the unlicensed users allowed to share the spectrum with the licensed users by respecting a tolerated interference threshold. A practical low complexity heuristic approach is proposed to solve our formulated optimization problem. Selected numerical results show that the proposed algorithm reaches a performance close to the performance of the optimal multiple relay selection scheme either with discrete or continuous power distributions while providing a considerable saving in terms of computational complexity. In addition, these results show that our proposed scheme significantly outperforms the single relay selection scheme. © 2013 IEEE.

Analysis of errors of radiation relay, (1)

International Nuclear Information System (INIS)

Koyanagi, Takami; Nakajima, Sinichi

1976-01-01

The statistical error of liquid level controlled by radiation relay is analysed and a method of minimizing the error is proposed. This method comes to the problem of optimum setting of the time constant of radiation relay. The equations for obtaining the value of time constant are presented and the numerical results are shown in a table and plotted in a figure. The optimum time constant of the upper level control relay is entirely different from that of the lower level control relay. (auth.)

49 CFR 236.52 - Relayed cut-section.

Science.gov (United States)

2010-10-01

..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Rules and Instructions: All Systems Track Circuits § 236.52 Relayed cut-section. Where relayed cut-section is used in... 49 Transportation 4 2010-10-01 2010-10-01 false Relayed cut-section. 236.52 Section 236.52...

Quantum cryptography with an ideal local relay

DEFF Research Database (Denmark)

Spedalieri, Gaetana; Ottaviani, Carlo; Braunstein, Samuel L.

2015-01-01

We consider two remote parties connected to a relay by two quantum channels. To generate a secret key, they transmit coherent states to the relay, where the states are subject to a continuous-variable (CV) Bell detection. We study the ideal case where Alice's channel is lossless, i.e., the relay ...

A SDP based design of relay precoding for the power minimization of MIMO AF-relay networks

KAUST Repository

Rao, Anlei; Park, Kihong; Alouini, Mohamed-Slim

2015-01-01

Relay precoding for multiple-input and multiple-output (MIMO) relay networks has been approached by either optimizing the efficiency performance with given power consumption constraints or minimizing the power consumption with quality-of-service (Qo

User Multiplexing in Relay Enhanced LTE-Advanced Networks

DEFF Research Database (Denmark)

Teyeb, Oumer Mohammed; Frederiksen, Frank; Redana, Simone

2010-01-01

is radio relaying. This uses relay nodes that act as surrogate base stations for mobile users whose radio links with the base stations are not experiencing good enough conditions. In the downlink, the data that is destined for the relayed users may first have to be multiplexed by the base station, sent...... over the wireless backhaul link towards the relay node, and de-multiplexed and forwarded to the individual users by the relay node. The reverse process also has to be undertaken in the uplink. In this paper, we present a novel multiplexing scheme which is able to adapt the addressing and bitmapping...... of user identification to the actual number of users being served by the relay nodes, and thus greatly reduce the multiplexing overhead....

Electrostatic potential map modelling with COSY Infinity

International Nuclear Information System (INIS)

Maloney, J.A.; Baartman, R.; Planche, T.; Saminathan, S.

2016-01-01

COSY Infinity (Makino and Berz, 2005) is a differential-algebra based simulation code which allows accurate calculation of transfer maps to arbitrary order. COSY’s existing internal procedures were modified to allow electrostatic elements to be specified using an array of field potential data from the midplane. Additionally, a new procedure was created allowing electrostatic elements and their fringe fields to be specified by an analytic function. This allows greater flexibility in accurately modelling electrostatic elements and their fringe fields. Applied examples of these new procedures are presented including the modelling of a shunted electrostatic multipole designed with OPERA, a spherical electrostatic bender, and the effects of different shaped apertures in an electrostatic beam line.

Amplify-and-forward relaying in wireless communications

CERN Document Server

Rodriguez, Leonardo Jimenez; Le-Ngoc, Tho

2015-01-01

This SpringerBrief explores the advantage of relaying techniques in addressing the increasing demand for high data rates and reliable services over the air. It demonstrates how to design cost-effective relay systems that provide high spectral efficiency and fully exploit the diversity of the relay channel. The brief covers advances in achievable rates, power allocation schemes, and error performance for half-duplex (HD) and full-duplex (FD) amplify-and-forward (AF) single-relay systems. The authors discuss the capacity and respective optimal power allocation for a wide range of HD protocols ov

Full-Duplex Relay Selection in Cognitive Underlay Networks

KAUST Repository

Khafagy, Mohammad Galal

2017-09-30

In this work, we analyze the performance of full-duplex relay selection (FDRS) in spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay(s), thereby allowing for a higher spectral efficiency. However, since the source and relay simultaneously transmit in FDR, their superimposed signal at the primary receiver should now satisfy the existing interference constraint, which can considerably limit the secondary network throughput. In this regard, relay selection can offer an adequate solution to boost the secondary throughput while satisfying the imposed interference limit. We first analyze the performance of opportunistic FDRS with residual self-interference (RSI) by deriving the exact cumulative distribution function of its end-to-end signal-to-interference-plus-noise ratio under Nakagami-m fading. We also evaluate the offered diversity gain of relay selection for different full-duplex cooperation schemes in the presence/absence of a direct source-destination link. When the adopted RSI link gain model is sublinear in the relay power, which agrees with recent research findings, we show that remarkable diversity gain can be recovered even in the presence of an interfering direct link. Second, we evaluate the end-to-end performance of FDRS with interference constraints due to the presence of a primary receiver. Finally, the presented exact theoretical findings are verified by numerical simulations.

Relay exchanges in elite short track speed skating.

Science.gov (United States)

Hext, Andrew; Heller, Ben; Kelley, John; Goodwill, Simon

2017-06-01

In short track speed skating, the relay exchange provides an additional strategic component to races by allowing a team to change the skater involved in the pack race. Typically executed every 1½ laps, it is the belief of skaters and coaches that during this period of the race, time can be gained or lost due to the execution of the relay exchange. As such, the aim of this study was to examine the influence of the relay exchange on a team's progression through a 5000 m relay race. Using data collected from three World Cup relay events during the 2012-2013 season, the time taken to complete the straight for the scenarios with and without the relay exchange were compared at different skating speeds for the corner exit prior to the straight. Overall, the influence of the relay exchange was found to be dependent on this corner exit speed. At slower corner exit speeds (12.01-13.5 m/s), relay exchange straight times were significantly faster than the free skating scenario (P < 0.01). While at faster corner exit speeds (14.01-15 m/s), straight times were significantly slower (P < 0.001). The findings of this study suggest that the current norm of executing relay exchanges every 1½ laps may not be optimal. Instead, varying the frequency of relay exchange execution throughout the race could allow: (1) time to be gained relative to other teams; and (2) facilitate other race strategies by providing an improved opportunity to overtake.

On Alternate Relaying with Improper Gaussian Signaling

KAUST Repository

Gaafar, Mohamed; Amin, Osama; Ikhlef, Aissa; Chaaban, Anas; Alouini, Mohamed-Slim

2016-01-01

In this letter, we investigate the potential benefits of adopting improper Gaussian signaling (IGS) in a two-hop alternate relaying (AR) system. Given the known benefits of using IGS in interference-limited networks, we propose to use IGS to relieve the inter-relay interference (IRI) impact on the AR system assuming no channel state information is available at the source. In this regard, we assume that the two relays use IGS and the source uses proper Gaussian signaling (PGS). Then, we optimize the degree of impropriety of the relays signal, measured by the circularity coefficient, to maximize the total achievable rate. Simulation results show that using IGS yields a significant performance improvement over PGS, especially when the first hop is a bottleneck due to weak source-relay channel gains and/or strong IRI.

On Alternate Relaying with Improper Gaussian Signaling

KAUST Repository

Gaafar, Mohamed

2016-06-06

In this letter, we investigate the potential benefits of adopting improper Gaussian signaling (IGS) in a two-hop alternate relaying (AR) system. Given the known benefits of using IGS in interference-limited networks, we propose to use IGS to relieve the inter-relay interference (IRI) impact on the AR system assuming no channel state information is available at the source. In this regard, we assume that the two relays use IGS and the source uses proper Gaussian signaling (PGS). Then, we optimize the degree of impropriety of the relays signal, measured by the circularity coefficient, to maximize the total achievable rate. Simulation results show that using IGS yields a significant performance improvement over PGS, especially when the first hop is a bottleneck due to weak source-relay channel gains and/or strong IRI.

An assessment of fire vulnerability for aged electrical relays

International Nuclear Information System (INIS)

Vigil, R.A.; Nowlen, S.P.

1995-03-01

There has been some concern that, as nuclear power plants age, protective measures taken to control and minimize the impact of fire may become ineffective, or significantly less effective, and hence result in an increased fire risk. One objective of the Fire Vulnerability of Aged Electrical Components Program is to assess the effects of aging and service wear on the fire vulnerability of electrical equipment. An increased fire vulnerability of components may lead to an overall increase in fire risk to the plant. Because of their widespread use in various electrical safety systems, electromechanical relays were chosen to be the initial components for evaluation. This test program assessed the impact of operational and thermal aging on the vulnerability of these relays to fire-induced damage. Only thermal effects of a fire were examined in this test program. The impact of smoke, corrosive materials, or fire suppression effects on relay performance were not addressed in this test program. The purpose of this test program was to assess whether the fire vulnerability of electrical relays increased with aging. The sequence followed for the test program was to: identify specific relay types, develop three fire scenarios, artificially age several relays, test the unaged and aged relays in the fire exposure scenarios, and compare the results. The relays tested were Agastat GPI, General Electric (GE) HMA, HGA, and HFA. At least two relays of each type were artificially aged and at least two relays of each type were new. Relays were operationally aged by cycling the relay under rated load for 2,000 operations. These relays were then thermally aged for 60 days with their coil energized

Microprocessor protection relays: new prospects or new problems?

OpenAIRE

Gurevich, Vladimir

2006-01-01

The internal architecture and principles of operation of microprocessor-based devices including so-called "microprocessor protective relays" have little in common with devices called "electric relays". But microprocessor-based relay protection devices are gradually driving out the traditional electromechanical and even electronic relay protection of virtually from all fields of power and electrical engineering. Advantages of microprocessor-based protection means over traditional ones are far ...

Cognitive Relay Networks: A Comprehensive Survey

Directory of Open Access Journals (Sweden)

Ayesha Naeem

2015-07-01

Full Text Available Cognitive radio is an emerging technology to deal with the scarcity and requirement of radio spectrum by dynamically assigning spectrum to unlicensed user . This revolutionary technology shifts the paradigm in the wireless system design by all owing unlicensed user the ability to sense, adapt and share the dynamic spectrum. Cognitive radio technology have been applied to different networks and applications ranging from wireless to public saf ety, smart grid, medical, rela y and cellular applications to increase the throughput and spectrum efficiency of the network. Among these applications, cognitive relay networks is one of the application where cognitive radio technology has been applied. Cognitiv e rela y network increases the network throughput by reducing the complete pa th loss and also by ensuring cooper ation among secondary users and cooperation among primary and secondary users. In this paper , our aim is to provide a survey on cognitive relay network. We also provide a detailed review on existing schemes in cognitive relay networks on the basis of relaying protocol, relay cooperation and channel model.

Error-rate performance analysis of opportunistic regenerative relaying

KAUST Repository

Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim

2011-01-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path can

Experimental evaluation of earthquake induced relay chattering

International Nuclear Information System (INIS)

Bandyopadhyay, K.; Hofmayer, C.; Shteyngart, S.

1990-01-01

An experimental evaluation of relay performance under vibratory environments is discussed in this paper. Single frequency excitation was used for most tests. Limited tests were performed with random multifrequency inputs. The capacity of each relay was established based on a two-millisecond chatter criterion. The experimental techniques are described and the effects of parameters in controlling the relay capacity levels are illustrated with test data. A wide variation of the capacity levels was observed due to the influence of parameters related to the design of the relay and nature of the input motion. 3 refs., 15 figs

Relay protection features of frequency-adjustable electric drive

Science.gov (United States)

Kuprienko, V. V.

2018-03-01

The features of relay protection of high-voltage electric motors in composition of the frequency-adjustable electric drive are considered in the article. The influence of frequency converters on the stability of the operation of various types of relay protection used on electric motors is noted. Variants of circuits for connecting relay protection devices are suggested. The need to develop special relay protection devices for a frequency-adjustable electric drive is substantiated.

Steering and timing system solutions at the COSY accelerator facility

International Nuclear Information System (INIS)

Bongers, N.; Hacker, U.; Henn, K.; Simon, M.; Vashegyi, T.; Weinert, A.

1994-01-01

Two components of the COSY control system are discussed. One is the system for control of the correction magnet power converters and the other is the timing system. The power converters are controlled by VME crate systems, each crate being able to control up to four power converters. The timing system consists of a VME timing system transmitter, a transmission network and receivers in the power converter crates. Figures for the resolution required and achieved are given. ((orig.))

Steering and timing system solutions at the COSY accelerator facility

Energy Technology Data Exchange (ETDEWEB)

Bongers, N [KFA, Juelich (Germany); Hacker, U [KFA, Juelich (Germany); Henn, K [KFA, Juelich (Germany); Simon, M [KFA, Juelich (Germany); Vashegyi, T [KFA, Juelich (Germany); Weinert, A [KFA, Juelich (Germany)

1994-12-15

Two components of the COSY control system are discussed. One is the system for control of the correction magnet power converters and the other is the timing system. The power converters are controlled by VME crate systems, each crate being able to control up to four power converters. The timing system consists of a VME timing system transmitter, a transmission network and receivers in the power converter crates. Figures for the resolution required and achieved are given. ((orig.))

Relay Telecommunications for the Coming Decade of Mars Exploration

Science.gov (United States)

Edwards, C.; DePaula, R.

2010-01-01

Over the past decade, an evolving network of relay-equipped orbiters has advanced our capabilities for Mars exploration. NASA's Mars Global Surveyor, 2001 Mars Odyssey, and Mars Reconnaissance Orbiter (MRO), as well as ESA's Mars Express Orbiter, have provided telecommunications relay services to the 2003 Mars Exploration Rovers, Spirit and Opportunity, and to the 2007 Phoenix Lander. Based on these successes, a roadmap for continued Mars relay services is in place for the coming decade. MRO and Odyssey will provide key relay support to the 2011 Mars Science Laboratory (MSL) mission, including capture of critical event telemetry during entry, descent, and landing, as well as support for command and telemetry during surface operations, utilizing new capabilities of the Electra relay payload on MRO and the Electra-Lite payload on MSL to allow significant increase in data return relative to earlier missions. Over the remainder of the decade a number of additional orbiter and lander missions are planned, representing new orbital relay service providers and new landed relay users. In this paper we will outline this Mars relay roadmap, quantifying relay performance over time, illustrating planned support scenarios, and identifying key challenges and technology infusion opportunities.

Study of light mesons with WASA-at-COSY

Science.gov (United States)

Prencipe, Elisabetta

2014-06-01

The WASA detector, operating at the COSY facility in Jülich (Germany) has been collecting data since 2007. The experiment allows to perform studies of light mesons, such as π0, η and ω rare decay processes, in order to perform precise measurements of branching ratios, determine Dalitz plot parameters, test symmetry and symmetry breaking, and evaluate transition form factors. In the experiments a proton or deuteron beam impinged on a pellet target of hydrogen or deuterium, which allows the reactions proton-proton (pp) or proton-deuteron (pd). A high-statistics sample of η mesons has been collected: in the reaction pd →3He η, 3×107η mesons were tagged at a beam energy of 1.0 GeV, while 5×108η mesons were produced in the reaction pp → ppη at 1.4 GeV. This corresponds to the production of 10 η/s and 100 η/s, respectively, for the two reaction processes. In the pp dataset a higher background level is found compared to the pd data set. In both cases, we identify the η mesons by means of the missing mass derived from the recoil particles. A kinematic fit largely rejects the background in our analysis. The advantage in using the pp dataset is that the production of η mesons is almost a factor of 10 higher than in the pd fusion to 3He. As we plan to measure the branching ratios of very rare processes, high statistics is needed. A summary of the recent activity on the study of light mesons with WASA-at-COSY here is given.

Study of light mesons with WASA-at-COSY

Directory of Open Access Journals (Sweden)

Prencipe Elisabetta

2014-06-01

Full Text Available The WASA detector, operating at the COSY facility in Jülich (Germany has been collecting data since 2007. The experiment allows to perform studies of light mesons, such as π0, η and ω rare decay processes, in order to perform precise measurements of branching ratios, determine Dalitz plot parameters, test symmetry and symmetry breaking, and evaluate transition form factors. In the experiments a proton or deuteron beam impinged on a pellet target of hydrogen or deuterium, which allows the reactions proton-proton (pp or proton-deuteron (pd. A high-statistics sample of η mesons has been collected: in the reaction pd →3He η, 3×107η mesons were tagged at a beam energy of 1.0 GeV, while 5×108η mesons were produced in the reaction pp → ppη at 1.4 GeV. This corresponds to the production of 10 η/s and 100 η/s, respectively, for the two reaction processes. In the pp dataset a higher background level is found compared to the pd data set. In both cases, we identify the η mesons by means of the missing mass derived from the recoil particles. A kinematic fit largely rejects the background in our analysis. The advantage in using the pp dataset is that the production of η mesons is almost a factor of 10 higher than in the pd fusion to 3He. As we plan to measure the branching ratios of very rare processes, high statistics is needed. A summary of the recent activity on the study of light mesons with WASA-at-COSY here is given.

Sum-Rate Enhancement in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

KAUST Repository

Benkhelifa, Fatma

2016-09-20

In this paper, we consider a multiuser multipleinput multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting (EH) relays and multiple destinations. All the nodes are equipped with multiple antennas. The EH and information decoding (ID) tasks at the relays and destinations are separated over the time, which is termed as the time switching (TS) scheme. As optimal solutions for the sum-rate maximization problems of BC channels and the MIMO interference channels are hard to obtain, the end-to-end sum rate maximization problem of a multiuser MIMO DF relay BC channel is even harder. In this paper, we propose to tackle a simplified problem where we employ the block diagonalization (BD) procedure at the source, and we mitigate the interference between the relaydestination channels using an algorithm similar to the BD method. In order to show the relevance of our low complex proposed solution, we compare it to the minimum mean-square error (MMSE) solution that was shown in the literature to be equivalent to the solution of the sum-rate maximization in MIMO broadcasting interfering channels. We also investigate the time division multiple access (TDMA) solution which separates all the information transmissions from the source to the relays and from the relays to the destinations over time. We provide numerical results to show the relevance of our proposed solution, in comparison with the no co-channel interference (CCI) case, the TDMA based solution and the MMSE based solution.

Sum-Rate Enhancement in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

KAUST Repository

Benkhelifa, Fatma; Salem, Ahmed Sultan; Alouini, Mohamed-Slim

2016-01-01

In this paper, we consider a multiuser multipleinput multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting (EH) relays and multiple destinations. All the nodes are equipped with multiple antennas. The EH and information decoding (ID) tasks at the relays and destinations are separated over the time, which is termed as the time switching (TS) scheme. As optimal solutions for the sum-rate maximization problems of BC channels and the MIMO interference channels are hard to obtain, the end-to-end sum rate maximization problem of a multiuser MIMO DF relay BC channel is even harder. In this paper, we propose to tackle a simplified problem where we employ the block diagonalization (BD) procedure at the source, and we mitigate the interference between the relaydestination channels using an algorithm similar to the BD method. In order to show the relevance of our low complex proposed solution, we compare it to the minimum mean-square error (MMSE) solution that was shown in the literature to be equivalent to the solution of the sum-rate maximization in MIMO broadcasting interfering channels. We also investigate the time division multiple access (TDMA) solution which separates all the information transmissions from the source to the relays and from the relays to the destinations over time. We provide numerical results to show the relevance of our proposed solution, in comparison with the no co-channel interference (CCI) case, the TDMA based solution and the MMSE based solution.

Application of 13C-labeling and 13C-13C COSY NMR experiments in the structure determination of a microbial natural product.

Science.gov (United States)

Kwon, Yun; Park, Sunghyouk; Shin, Jongheon; Oh, Dong-Chan

2014-08-01

The elucidation of the structures of complex natural products bearing many quaternary carbons remains challenging, even in this advanced spectroscopic era. (13)C-(13)C COSY NMR spectroscopy shows direct couplings between (13)C and (13)C, which comprise the backbone of a natural product. Thus, this type of experiment is particularly useful for natural products bearing consecutive quaternary carbons. However, the low sensitivity of (13)C-based NMR experiments, due to the low natural abundance of the (13)C nucleus, is problematic when applying these techniques. Our efforts in the (13)C labeling of a microbial natural product, cyclopiazonic acid (1), by feeding (13)C-labeled glucose to the fungal culture, enabled us to acquire (13)C-(13)C COSY NMR spectra on a milligram scale that clearly show the carbon backbone of the compound. This is the first application of (13)C-(13)C COSY NMR experiments for a natural product. The results suggest that (13)C-(13)C COSY NMR spectroscopy can be routinely used for the structure determination of microbial natural products by (13)C-enrichment of a compound with (13)C-glucose.

Evaluation of Harmonics Impact on Digital Relays

Directory of Open Access Journals (Sweden)

Kinan Wannous

2018-04-01

Full Text Available This paper presents the concept of the impact of harmonic distortion on a digital protection relay. The aim is to verify and determine the reasons of a mal-trip or failure to trip the protection relays; the suggested solution of the harmonic distortion is explained by a mathematical model in the Matlab Simulink programming environment. The digital relays have been tested under harmonic distortions in order to verify the function of the relays algorithm under abnormal conditions. The comparison between the protection relay algorithm under abnormal conditions and a mathematical model in the Matlab Simulink programming environment based on injected harmonics of high values is provided. The test is separated into different levels; the first level is based on the harmonic effect of an individual harmonic and mixed harmonics. The test includes the effect of the harmonics in the location of the fault point into distance protection zones. This paper is a new proposal in the signal processing of power quality disturbances using Matlab Simulink and the power quality impact on the measurements of the power system quantities; the test simulates the function of protection in power systems in terms of calculating the current and voltage values of short circuits and their faults. The paper includes several tests: frequency variations and decomposition of voltage waveforms with Fourier transforms (model and commercial relay, the effect of the power factor on the location of fault points, the relation between the tripping time and the total harmonic distortion (THD levels in a commercial relay, and a comparison of the THD capture between the commercial relay and the model.

Relay testing parametric investigation of seismic fragility

International Nuclear Information System (INIS)

Bandyopadhyay, K.; Hofmayer, C.; Kassir, M.; Pepper, S.

1989-01-01

The seismic capacity of most electrical equipment is governed by malfunction of relays. An evaluation of the existing relay test data base at Brookhaven National Laboratory (BNL) has indicated that the seismic fragility of a relay may depend on various parameters related to the design or the input motion. In particular, the electrical mode, contact state, adjustment, chatter duration acceptance limit, and the frequency and the direction of the vibration input have been considered to influence the relay fragility level. For a particular relay type, the dynamics of its moving parts depends on the exact model number and vintage and hence, these parameters may also influence the fragility level. In order to investigate the effect of most of these parameters on the seismic fragility level, BNL has conducted a relay test program. The testing has been performed at Wyle Laboratories. Establishing the correlation between the single frequency fragility test input and the corresponding multifrequency response spectrum (TRS) is also an objective of this test program. This paper discusses the methodology used for testing and presents a brief summary of important test results. 1 ref., 10 figs

Test of time-reversal invariance at COSY (TRIC)

Energy Technology Data Exchange (ETDEWEB)

Eversheim, D., E-mail: evershei@hiskp.uni-bonn.de; Valdau, Yu. [University Bonn, Helmholtz Institut fuer Strahlen- und Kernphysik (Germany); Lorentz, B. [Forschungszentrum Juelich, Institut fuer Kernphysik (Germany)

2013-03-15

At the Cooler Synchrotron COSY a novel (P-even, T-odd) null test of time-reversal invariance to an accuracy of 10{sup - 6} is planned as an internal target transmission experiment. The parity conserving time-reversal violating observable is the total cross-section asymmetry A{sub y,xz}. This quantity is measured using a polarized proton beam with an energy of 135 MeV and an internal tensor polarized deuteron target from the PAX atomic beam source. The reaction rate will be measured by means of an integrating beam current transformer. Thus, in this experiment the cooler synchroton ring serves as ideal forward spectrometer, as a detector, and an accelerator.

Capacity Bounds and Mapping Design for Binary Symmetric Relay Channels

Directory of Open Access Journals (Sweden)

Majid Nasiri Khormuji

2012-12-01

Full Text Available Capacity bounds for a three-node binary symmetric relay channel with orthogonal components at the destination are studied. The cut-set upper bound and the rates achievable using decode-and-forward (DF, partial DF and compress-and-forward (CF relaying are first evaluated. Then relaying strategies with finite memory-length are considered. An efficient algorithm for optimizing the relay functions is presented. The Boolean Fourier transform is then employed to unveil the structure of the optimized mappings. Interestingly, the optimized relay functions exhibit a simple structure. Numerical results illustrate that the rates achieved using the optimized low-dimensional functions are either comparable to those achieved by CF or superior to those achieved by DF relaying. In particular, the optimized low-dimensional relaying scheme can improve on DF relaying when the quality of the source-relay link is worse than or comparable to that of other links.

Initial investigations of (np)-scattering with a polarized deuterium target at ANKE-COSY

Energy Technology Data Exchange (ETDEWEB)

Gou, Boxing

2015-07-01

The understanding of the forces among nucleons is fundamental to the whole of nuclear and hadronic physics. The nucleon-nucleon (NN) scattering is the ideal probe to study the nuclear forces. The scattering amplitudes for the complete description of the NN interactions can be reconstructed from phase-shift analyses (PSA), which requires measurements with polarized experiments. The existing data allow to extract unambiguous proton-proton (pp) amplitudes below 2 GeV. However, there is very little known about the neutron-proton (np) system above 800 MeV nucleon energy. THE ANKE-COSY collaboration has embarked on a systematic program which aims to extract the np scattering amplitudes through the deuteron-proton charge-exchange process dp→{pp}{sub s}n. First part of the program via polarized deuteron beam and hydrogen target allowed successful measurement of np amplitudes up to 1.135 GeV nucleon energy, which is the maximum nucleon energy that can be accessed with deuteron beam at COSY. Via inverse kinematics, i.e. using a proton beam incident on a polarized deuterium target will allow to enhance the np study up to 2.8 GeV, the highest energy available at COSY. The method of inverse kinematics has to be validated prior to the production experiment. As the proof-of-principle (POP) experiment, the initial research has been conducted at proton energy T{sub p}=600 MeV using a polarized deuterium target. The projectiles were measured by two silicon tracking telescopes (STT) placed closed to the target and by the ANKE sub-detection systems. Four polarization modes of the deuterium target were employed. In order to increase the effective target thickness, polarized deuterium atoms produced by the atomic beam source (ABS) was filled into a storage cell, where the circulating COSY beam collides with the target. The target polarizations were measured using the proton-deuteron elastic reaction. The vector and tensor analyzing powers A{sub y} and A{sub yy} of pvector d�

Duplex Schemes in Multiple Antenna Two-Hop Relaying

Directory of Open Access Journals (Sweden)

Anja Klein

2008-04-01

Full Text Available A novel scheme for two-hop relaying defined as space division duplex (SDD relaying is proposed. In SDD relaying, multiple antenna beamforming techniques are applied at the intermediate relay station (RS in order to separate downlink and uplink signals of a bi-directional two-hop communication between two nodes, namely, S1 and S2. For conventional amplify-and-forward two-hop relaying, there appears a loss in spectral efficiency due to the fact that the RS cannot receive and transmit simultaneously on the same channel resource. In SDD relaying, this loss in spectral efficiency is circumvented by giving up the strict separation of downlink and uplink signals by either time division duplex or frequency division duplex. Two novel concepts for the derivation of the linear beamforming filters at the RS are proposed; they can be designed either by a three-step or a one-step concept. In SDD relaying, receive signals at S1 are interfered by transmit signals of S1, and receive signals at S2 are interfered by transmit signals of S2. An efficient method in order to combat this kind of interference is proposed in this paper. Furthermore, it is shown how the overall spectral efficiency of SDD relaying can be improved if the channels from S1 and S2 to the RS have different qualities.

Two-Hop Secure Communication Using an Untrusted Relay

Directory of Open Access Journals (Sweden)

Xiang He

2009-01-01

Full Text Available We consider a source-destination pair that can only communicate through an untrusted intermediate relay node. The intermediate node is willing to employ a designated relaying scheme to facilitate reliable communication between the source and the destination. Yet, the information it relays needs to be kept secret from it. In this two-hop communication scenario, where the use of the untrusted relay node is essential, we find that a positive secrecy rate is achievable. The center piece of the achievability scheme is the help provided by either the destination node with transmission capability, or an external “good samaritan” node. In either case, the helper performs cooperative jamming that confuses the eavesdropping relay and disables it from being able to decipher what it is relaying. We next derive an upper bound on the secrecy rate for this system. We observe that the gap between the upper bound and the achievable rate vanishes as the power of the relay node goes to infinity. Overall, the paper presents a case for intentional interference, that is, cooperative jamming, as an enabler for secure communication.

Energy-efficient relay selection and optimal power allocation for performance-constrained dual-hop variable-gain AF relaying

KAUST Repository

Zafar, Ammar; Radaydeh, Redha Mahmoud Mesleh; Chen, Yunfei; Alouini, Mohamed-Slim

2013-01-01

This paper investigates the energy-efficiency enhancement of a variable-gain dual-hop amplify-and-forward (AF) relay network utilizing selective relaying. The objective is to minimize the total consumed power while keeping the end-to-end signal

Application of a proposed overcurrent relay in radial distribution networks

Energy Technology Data Exchange (ETDEWEB)

Conde, A.; Vazquez, E. [Universidad Autonoma de Nuevo Leon, Facultad de Ingenieria Mecanica y Electrica, A.P. 36-F, CU, CP 66450, San Nicolas de los Garza, Nuevo Leon (Mexico)

2011-02-15

This paper contains the application criteria and coordination process for a proposed overcurrent relay in a radial power system with feed from one or multiple sources. This relay uses independent functions to detect faults and to calculate the operation time. Also this relay uses a time element function that allows it to reduce the time relay operation, enhancing the backup protection. Some of the proposed approaches improve the sensitivity of the relay. The selection of the best approach in the proposed relay is defined by the needs of the application. The proposed protection can be considered as an additional function protection to conventional overcurrent relays. (author)

Time of arrival based location estimation for cooperative relay networks

KAUST Repository

Ç elebi, Hasari Burak; Abdallah, Mohamed M.; Hussain, Syed Imtiaz; Qaraqe, Khalid A.; Alouini, Mohamed-Slim

2010-01-01

In this paper, we investigate the performance of a cooperative relay network performing location estimation through time of arrival (TOA). We derive Cramer-Rao lower bound (CRLB) for the location estimates using the relay network. The analysis is extended to obtain average CRLB considering the signal fluctuations in both relay and direct links. The effects of the channel fading of both relay and direct links and amplification factor and location of the relay node on average CRLB are investigated. Simulation results show that the channel fading of both relay and direct links and amplification factor and location of relay node affect the accuracy of TOA based location estimation. ©2010 IEEE.

Time of arrival based location estimation for cooperative relay networks

KAUST Repository

Çelebi, Hasari Burak

2010-09-01

In this paper, we investigate the performance of a cooperative relay network performing location estimation through time of arrival (TOA). We derive Cramer-Rao lower bound (CRLB) for the location estimates using the relay network. The analysis is extended to obtain average CRLB considering the signal fluctuations in both relay and direct links. The effects of the channel fading of both relay and direct links and amplification factor and location of the relay node on average CRLB are investigated. Simulation results show that the channel fading of both relay and direct links and amplification factor and location of relay node affect the accuracy of TOA based location estimation. ©2010 IEEE.

Full-Duplex opportunistic relay selection in future spectrum-sharing networks

KAUST Repository

Khafagy, Mohammad Galal; Alouini, Mohamed-Slim; Aï ssa, Sonia

2015-01-01

We propose and analyze the performance of full-duplex relay selection in primary/secondary spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay, thereby allowing for a higher spectral efficiency. However, since the source and relay simultaneously transmit in FDR, their superimposed signal at the primary receiver should now satisfy the existing interference constraint which can considerably limit the secondary network throughput. In this regard, relay selection can offer an adequate solution to boost the secondary throughput while satisfying the imposed interference limit. We first analyze the performance of opportunistic relay selection among a cluster of full-duplex decode-and-forward relays with self-interference by deriving the exact cumulative distribution function of its end-to-end signal-to-noise ratio. Second, we evaluate the end-to-end performance of relay selection with interference constraints due to the presence of a primary receiver. Finally, the presented exact theoretical findings are verified by numerical simulations.

Full-Duplex opportunistic relay selection in future spectrum-sharing networks

KAUST Repository

Khafagy, Mohammad Galal

2015-06-01

We propose and analyze the performance of full-duplex relay selection in primary/secondary spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay, thereby allowing for a higher spectral efficiency. However, since the source and relay simultaneously transmit in FDR, their superimposed signal at the primary receiver should now satisfy the existing interference constraint which can considerably limit the secondary network throughput. In this regard, relay selection can offer an adequate solution to boost the secondary throughput while satisfying the imposed interference limit. We first analyze the performance of opportunistic relay selection among a cluster of full-duplex decode-and-forward relays with self-interference by deriving the exact cumulative distribution function of its end-to-end signal-to-noise ratio. Second, we evaluate the end-to-end performance of relay selection with interference constraints due to the presence of a primary receiver. Finally, the presented exact theoretical findings are verified by numerical simulations.

Discrete radioisotopic relays of a cyclic action

International Nuclear Information System (INIS)

Klempner, K.S.; Vasil'ev, A.G.

1975-01-01

A functional diagram of discrete radioisotopic relay equipment (RRP) with cyclic action was examined. An analysis of its rapid action and reliability under stationary conditions and transition regimes is presented. A structural diagram of radioisotopic relay equipment shows three radiation detectors, a pulse standardizer, an integrator and a power amplifier with a threshold cut-off device. It was established that the basic properties of the RRP - rapid action and reliability - are determined entirely by the counting rate of the average frequency of pulses from the radiation detector, n 0 and n 1 , in the 0 and 1 states (absence of current in the electromagnetic relay winding and activation of the winding of the output relay), capacities N 1 and N 2 of the dual counters, and the frequency of the transition threshold, f, of the generator. Formulas are presented which allow making engineering calculations for determining the optimum RRP parameters. High speed and reliability are shown, which are determined by the production purposes of the relay

Asymmetric Modulation Gains in Network Coded Relay Networks

DEFF Research Database (Denmark)

Roetter, Daniel Enrique Lucani; Fitzek, Frank

2015-01-01

Wireless relays have usually been considered in two ways. On the one hand, a physical layer approach focused on per-packet reliability and involving the relay on each packet transmission. On the other, recent approaches have relied on the judicious activation of the relay at the network level to ...

Beamforming Design for Coordinated Direct and Relay Systems

DEFF Research Database (Denmark)

Sun, Fan; De Carvalho, Elisabeth; Thai, Chan

2012-01-01

Joint processing of multiple communication flows in wireless systems has given rise to a number of novel transmission techniques, notably the two-way relaying based on wireless network coding. Recently, a related set of techniques has emerged, termed coordinated direct and relay (CDR) transmissions......, where the constellation of traffic flows is more general than the two-way. Regardless of the actual traffic flows, in a CDR scheme the relay has a central role in managing the interference. In this paper we investigate the novel transmission modes, based on amplify-and-forward, that arise when the relay...... an iterative solution, as well as derive an upper performance bound. The numerical results demonstrate a clear benefit from usage of multiple antennas at the relay node....

Robust distributed cognitive relay beamforming

KAUST Repository

Pandarakkottilil, Ubaidulla

2012-05-01

In this paper, we present a distributed relay beamformer design for a cognitive radio network in which a cognitive (or secondary) transmit node communicates with a secondary receive node assisted by a set of cognitive non-regenerative relays. The secondary nodes share the spectrum with a licensed primary user (PU) node, and each node is assumed to be equipped with a single transmit/receive antenna. The interference to the PU resulting from the transmission from the cognitive nodes is kept below a specified limit. The proposed robust cognitive relay beamformer design seeks to minimize the total relay transmit power while ensuring that the transceiver signal-to-interference- plus-noise ratio and PU interference constraints are satisfied. The proposed design takes into account a parameter of the error in the channel state information (CSI) to render the performance of the beamformer robust in the presence of imperfect CSI. Though the original problem is non-convex, we show that the proposed design can be reformulated as a tractable convex optimization problem that can be solved efficiently. Numerical results are provided and illustrate the performance of the proposed designs for different network operating conditions and parameters. © 2012 IEEE.

Distance relay performance in future converter dominated power systems

DEFF Research Database (Denmark)

Sarkar, Moumita; Jia, Jundi; Yang, Guangya

2017-01-01

Increasing penetration of converter-based generations in power system has led to new system challenges. Short circuit power response from converter-based generations is different from that of traditional synchronous generators. Power electronic converters can be designed for over-current only up ...... of converter controls on fault current response of converter-based generations is also investigated. Index Terms—Converter control, distance relays, power system protection, system modelling....... to 1.1-1.25 times of its nominal value. Low availability of short circuit power can cause many challenges such as misoperation of distance relays. The aim of this paper is to investigate the effect of converter dominated systems on performance of distance relays. Backup functionality of the distance...... relay is major concern as miscoordination of backup relays in case of cascading faults can lead to severe stress in system, which can develop into blackout. In this paper, response of relays in traditional system is compared with response of relays in low short-circuit-current power systems. Impact...

Distributed stability control using intelligent voltage-margin relay

Energy Technology Data Exchange (ETDEWEB)

Wiszniewski, A.; Rebizant, W. [Wroclaw Univ. of Technology (Poland); Klimek, A. [Powertech Labs Inc., Surrey, BC (Canada)

2010-07-01

This paper presented an intelligent relay that operates if the load to source impedance ratio decreases to a level that is dangerously close to the stability limit, which leads to power system blackouts. The intelligent voltage-margin/difference relay installed at receiving substations automatically initiates action if the voltage stability margin drops to a dangerously low level. The relay decides if the tap changing devices are to be blocked and if under-voltage load shedding should be initiated, thereby mitigating an evolving instability. The intelligent relay has two levels of operation. At the first stage, which corresponds to the higher load to source impedance ratio, the relay initiates blocking of the tap changer. At the second stage, corresponding to the lower source to load impedance ratio, load shedding is initiated. The relay operates when the load to source impedance ratio reaches a certain predetermined level, but it does not depend either on the level of the source voltage or on the difference of source and load impedance phase angles. The algorithm for the relay is relatively simple and uses only locally available signals. Consequently, the transformer is well controlled to eliminate the cases of voltage instability. 6 refs., 7 figs.

Asymptotic analysis for Nakagami-m fading channels with relay selection

KAUST Repository

Zhong, Caijun

2011-06-01

In this paper, we analyze the asymptotic outage probability performance of both decode-and-forward (DF) and amplify-and-forward (AF) relaying systems using partial relay selection and the "best" relay selection schemes for Nakagami-m fading channels. We derive their respective outage probability expressions in the asymptotic high signal-to-noise ratio (SNR) regime, from which the diversity order and coding gain are analyzed. In addition, we investigate the impact of power allocation between the source and relay terminals and derive the diversity-multiplexing tradeoff (DMT) for these relay selection systems. The theoretical findings suggest that partial relay selection can improve the diversity of the system and can achieve the same DMT as the "best" relay selection scheme under certain conditions. © 2011 IEEE.

LTE-Advanced Relay Technology and Standardization

CERN Document Server

Yuan, Yifei

2013-01-01

LTE-Advanced Relay Technology and Standardization provides a timely reference work for relay technology with the finalizing of LTE Release 10 specifications. LTE-Advanced is quickly becoming the global standard for 4G cellular communications. The relay technology, as one of the key features in LTE-Advanced, helps not only to improve the system coverage and capacity, but also to save the costs of laying wireline backhaul. As a leading researcher in the field of LTE-Advanced standards, the author provides an in-depth description of LTE-A relay technology, and explains in detail the standard specification and design principles.     Readers from both academic and industrial fields can find sections of interest to them: Sections 2 & 4 could benefit researchers in academia and those who are engaged in exploratory work, while Sections 3 & 4 are more useful to engineers. Dr. Yifei Yuan is the Technical Director at the Standards Department of ZTE Inc.

New results on performance analysis of opportunistic regenerative relaying

KAUST Repository

Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim; Qaraqe, Khalid A.

2013-01-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path may

Accurate performance analysis of opportunistic decode-and-forward relaying

KAUST Repository

Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim

2011-01-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path may

Determination of deuteron beam polarizations at COSY

Directory of Open Access Journals (Sweden)

D. Chiladze

2006-05-01

Full Text Available The vector (P_{z} and tensor (P_{zz} polarizations of a deuteron beam have been measured using elastic deuteron–carbon scattering at 75.6 MeV and deuteron-proton scattering at 270 MeV. After acceleration to 1170 MeV inside the COSY storage ring, the polarizations of the deuterons were remeasured by studying the analyzing powers of a variety of nuclear reactions. For this purpose a hydrogen cluster target was employed at the ANKE magnetic spectrometer, which is situated at an internal target position in the ring. The overall precisions obtained were about 4% for both P_{z} and P_{zz}. Though all the measurements were consistent with the absence of depolarization during acceleration, only an upper limit of about 6% could be placed on such an effect.

Electric equipment technical regulation on a relay

International Nuclear Information System (INIS)

1995-01-01

It is about a relay for power protection. It describes the definitions of structure, a point of contact protection of contact, reclosing, relay scheme and input circuit. It explains normal use condition, special use condition, rated frequency, rated voltage and rated current, fluctuation range of permission of incoming relay. It deals with general structing outer case, correction device, operation indicator and outer terminal condition sort and method of the test. It adds the marks and pictures about currents

Location-based Relay Selection and Power Adaptation Enabling Simultaneous Transmissions

DEFF Research Database (Denmark)

Nielsen, Jimmy Jessen; Madsen, Tatiana Kozlova; Schwefel, Hans-Peter

2010-01-01

Relaying is a well known technique to extend coverage and improve conditions for nodes in the outer coverage region. In this paper we propose a relaying scheme that exploits the spatial separation of relay and destination pairs to improve throughput by allowing simultaneous transmissions....... The proposed scheme is a cross-layer optimization for two-hop relaying that uses position information to jointly optimize relay selection and relay transmit power, maximizing Medium Access Control layer throughput. Further, in order to calculate the expected throughput, we apply a probabilistic model...... that takes into account MAC retransmissions and timing behavior of the IEEE 802.11 Distributed Coordination Function mode. Our results show an increase in throughput of approximately 20% is achievable for the proposed scheme when compared to two-hop relaying in the analyzed scenario....

Performance of hybrid-ARQ with incremental redundancy over relay channels

KAUST Repository

Chelli, Ali

2012-12-01

In this paper, we consider a relay network consisting of a source, a relay, and a destination. The source transmits a message to the destination using hybrid automatic repeat request (HARQ) with incremental redundancy (IR). The relay overhears the transmitted messages over the different HARQ rounds and tries to decode the data packet. In case of successful decoding at the relay, both the relay and the source cooperate to transmit the message to the destination. A maximum number M of HARQ rounds is considered. The channel realizations are independent for different HARQ rounds. We assume Rayleigh fading channels for the links source-relay, source-destination, and relay-destination. We investigate the performance of HARQ-IR over relay channel from an information theoretic perspective. Analytical expressions are derived for the information outage probability, the average number of transmissions, and the average transmission rate. We illustrate through our investigation the benefit of relaying. We also show the impact of the target outage probability and the maximum number M of HARQ rounds on the outage probability, the average number of transmissions, and the average transmission rate. © 2012 IEEE.

On Buffer-Aided Multiple-Access Relay Channel

DEFF Research Database (Denmark)

Liu, Rongkuan; Popovski, Petar; Wang, Gang

2016-01-01

This letter treats uplink scenario where M user equipments (UEs) send to a base station (BS), possibly via a common relay station (RS) that is equipped with a buffer. This is a multiple-access relay channel aided by a buffer. We devise a protocol in which the transmission mode is selected...... entirely at the BS, while simultaneously a number of UEs sends new messages to the BS. The results show that the adaptive selection of direct and buffer-aided relay transmissions leads to significant average throughput gains....

Cooperative AF Relaying in Spectrum-Sharing Systems: Outage Probability Analysis under Co-Channel Interferences and Relay Selection

KAUST Repository

Xia, Minghua

2012-11-01

For cooperative amplify-and-forward (AF) relaying in spectrum-sharing wireless systems, secondary users share spectrum resources originally licensed to primary users to communicate with each other and, thus, the transmit power of secondary transmitters is strictly limited by the tolerable interference powers at primary receivers. Furthermore, the received signals at a relay and at a secondary receiver are inevitably interfered by the signals from primary transmitters. These co-channel interferences (CCIs) from concurrent primary transmission can significantly degrade the performance of secondary transmission. This paper studies the effect of CCIs on outage probability of the secondary link in a spectrum-sharing environment. In particular, in order to compensate the performance loss due to CCIs, the transmit powers of a secondary transmitter and its relaying node are respectively optimized with respect to both the tolerable interference powers at the primary receivers and the CCIs from the primary transmitters. Moreover, when multiple relays are available, the technique of opportunistic relay selection is exploited to further improve system performance with low implementation complexity. By analyzing lower and upper bounds on the outage probability of the secondary system, this study reveals that it is the tolerable interference powers at primary receivers that dominate the system performance, rather than the CCIs from primary transmitters. System designers will benefit from this result in planning and designing next-generation broadband spectrum-sharing systems.

Relay self interference minimisation using tapped filter

KAUST Repository

Jazzar, Saleh; Al-Naffouri, Tareq Y.

2013-01-01

In this paper we introduce a self interference (SI) estimation and minimisation technique for amplify and forward relays. Relays are used to help forward signals between a transmitter and a receiver. This helps increase the signal coverage

Relay selection from an effective capacity perspective

KAUST Repository

Yang, Yuli; Ma, Hao; Aï ssa, Sonia

2013-01-01

proposed scheme in certain scenarios. Moreover, the analysis presented herein offers a convenient tool to the relaying transmission design, specifically on which relay selection scheme should be used as well as how to choose the receiving strategy between

Microstructure of buried CoSi2 layers formed by high-dose Co implantation into (100) and (111) Si substrates

International Nuclear Information System (INIS)

Bulle-Lieuwma, C.W.T.; Van Ommen, A.H.; Vandenhoudt, D.E.W.; Ottenheim, J.J.M.; de Jong, A.F.

1991-01-01

Heteroepitaxial Si/CoSi 2 /Si structures have been synthesized by implanting 170-keV Co + with doses in the range 1--3x10 17 Co + ions/cm 2 into (100) and (111) Si substrates and subsequent annealing. The microstructure of both the as-implanted and annealed structures is investigated in great detail by transmission electron microscopy, high-resolution electron microscopy, and x-ray diffraction. In the as-implanted samples, the Co is present as CoSi 2 precipitates, occurring both in aligned (A-type) and twinned (B-type) orientation. For the highest dose, a continuous layer of stoichiometric CoSi 2 is already formed during implantation. It is found that the formation of a connected layer, already during implantation, is crucial for the formation of a buried CoSi 2 layer upon subsequent annealing. Particular attention is given to the coordination of the interfacial Co atoms at the Si/CoSi 2 (111) interfaces of both types of precipitates. We find that the interfacial Co atoms at the A-type interfaces are fully sevenfold coordinated, whereas at the B-type interfaces they appear to be eightfold coordinated

76 FR 72124 - Internet-Based Telecommunications Relay Service Numbering

Science.gov (United States)

2011-11-22

... Docket No. 10-191; FCC 11-123] Internet-Based Telecommunications Relay Service Numbering AGENCY: Federal..., the information collection associated with the Commission's Internet- Based Telecommunications Relay... Telecommunications Relay Service Numbering, CG Docket No. 03-123; WC Docket No. 05-196; WC Docket No. 10-191; FCC 11...

Using a micromachined magnetostatic relay in commutating a DC motor

Science.gov (United States)

Tai, Yu-Chong (Inventor); Wright, John A. (Inventor); Lilienthal, Gerald (Inventor)

2004-01-01

A DC motor is commutated by rotating a magnetic rotor to induce a magnetic field in at least one magnetostatic relay in the motor. Each relay is activated in response to the magnetic field to deliver power to at least one corresponding winding connected to the relay. In some cases, each relay delivers power first through a corresponding primary winding and then through a corresponding secondary winding to a common node. Specific examples include a four-pole, three-phase motor in which each relay is activated four times during one rotation of the magnetic rotor.

Relay-assited transmission and radio resource management for wireless networks

OpenAIRE

Agustín de Dios, Adrián

2008-01-01

La transmisión asistida por relay o transmisión cooperativa es una nueva técnica de diversidad espacial donde aparece un elemento nuevo (un relay o un usuario cooperativo) en la tradicional transmisión punto a punto (fuente a destino). Ahora en la comunicación intervienen tres enlaces: fuente-relay, relay-destino y fuente-destino. El relay, además de asistir a la fuente en la transmisión de un mensaje, permite combatir las degradaciones que puede sufrir el canal como el shadowing y el pathlos...

Optimized Policies for Improving Fairness of Location-based Relay Selection

DEFF Research Database (Denmark)

Nielsen, Jimmy Jessen; Olsen, Rasmus Løvenstein; Madsen, Tatiana Kozlova

2013-01-01

For WLAN systems in which relaying is used to improve throughput performance for nodes located at the cell edge, node mobility and information collection delays can have a significant impact on the performance of a relay selection scheme. In this paper we extend our existing Markov Chain modeling...... framework for relay selection to allow for efficient calculation of relay policies given either mean throughput or kth throughput percentile as optimization criterium. In a scenario with static access point, static relay, and a mobile destination node, the kth throughput percentile optimization...

Generalized instantly decodable network coding for relay-assisted networks

KAUST Repository

Elmahdy, Adel M.

2013-09-01

In this paper, we investigate the problem of minimizing the frame completion delay for Instantly Decodable Network Coding (IDNC) in relay-assisted wireless multicast networks. We first propose a packet recovery algorithm in the single relay topology which employs generalized IDNC instead of strict IDNC previously proposed in the literature for the same relay-assisted topology. This use of generalized IDNC is supported by showing that it is a super-set of the strict IDNC scheme, and thus can generate coding combinations that are at least as efficient as strict IDNC in reducing the average completion delay. We then extend our study to the multiple relay topology and propose a joint generalized IDNC and relay selection algorithm. This proposed algorithm benefits from the reception diversity of the multiple relays to further reduce the average completion delay in the network. Simulation results show that our proposed solutions achieve much better performance compared to previous solutions in the literature. © 2013 IEEE.

Physical-Layer Security of a Buffer-Aided Full-Duplex Relaying System

KAUST Repository

El Shafie, Ahmed

2016-07-07

This letter proposes a novel hybrid half-/full-duplex relaying scheme to enhance the relay channel security. A source node (Alice) communicates with her destination node (Bob) in the presence of a buffer-aided full-duplex relay node (Rooney) and a potential eavesdropper (Eve). Rooney adopts two different relaying, namely randomize-and-forward and decode-andforward relaying strategies, to improve the security of the legitimate system. In the first relaying strategy, Rooney uses a codebook different from that used at Alice. In the second relaying strategy, Rooney and Alice use the same codebooks. In addition, Rooney switches between half-duplex and full-duplex modes to further enhance the security of the legitimate system. The numerical results demonstrate that our proposed scheme achieves a significant average secrecy end-to-end throughput improvement relative to the conventional bufferless full-duplex relaying scheme.

Optimal Contract Design for Cooperative Relay Incentive Mechanism under Moral Hazard

Directory of Open Access Journals (Sweden)

Nan Zhao

2015-01-01

Full Text Available Cooperative relay can effectively improve spectrum efficiency by exploiting the spatial diversity in the wireless networks. However, wireless nodes may acquire different network information with various users’ location and mobility, channels’ conditions, and other factors, which results in asymmetric information between the source and the relay nodes (RNs. In this paper, the relay incentive mechanism between relay nodes and the source is investigated under the asymmetric information. By modelling multiuser cooperative relay as a labour market, a contract model with moral hazard for relay incentive is proposed. To effectively incentivize the potential RNs to participate in cooperative relay, the optimization problems are formulated to maximize the source’s utility while meeting the feasible conditions under both symmetric and asymmetric information scenarios. Numerical simulation results demonstrate the effectiveness of the proposed contract design scheme for cooperative relay.

Physical-Layer Security of a Buffer-Aided Full-Duplex Relaying System

KAUST Repository

El Shafie, Ahmed; Salem, Ahmed Sultan; Al-Dhahir, Naofal

2016-01-01

This letter proposes a novel hybrid half-/full-duplex relaying scheme to enhance the relay channel security. A source node (Alice) communicates with her destination node (Bob) in the presence of a buffer-aided full-duplex relay node (Rooney) and a potential eavesdropper (Eve). Rooney adopts two different relaying, namely randomize-and-forward and decode-andforward relaying strategies, to improve the security of the legitimate system. In the first relaying strategy, Rooney uses a codebook different from that used at Alice. In the second relaying strategy, Rooney and Alice use the same codebooks. In addition, Rooney switches between half-duplex and full-duplex modes to further enhance the security of the legitimate system. The numerical results demonstrate that our proposed scheme achieves a significant average secrecy end-to-end throughput improvement relative to the conventional bufferless full-duplex relaying scheme.

A performance analysis in AF full duplex relay selection network

Science.gov (United States)

Ngoc, Long Nguyen; Hong, Nhu Nguyen; Loan, Nguyen Thi Phuong; Kieu, Tam Nguyen; Voznak, Miroslav; Zdralek, Jaroslav

2018-04-01

This paper studies on the relaying selective matter in amplify-and-forward (AF) cooperation communication with full-duplex (FD) activity. Various relay choice models supposing the present of different instant information are investigated. We examine a maximal relaying choice that optimizes the instant FD channel capacity and asks for global channel state information (CSI) as well as partial CSI learning. To make comparison easy, accurate outage probability clauses and asymptote form of these strategies that give a diversity rank are extracted. From that, we can see clearly that the number of relays, noise factor, the transmittance coefficient as well as the information transfer power had impacted on their performance. Besides, the optimal relay selection (ORS) model can promote than that of the partial relay selection (PRS) model.

STUDI ANALISIS KOORDINASI OVER CURRENT RELAY (OCR DAN GROUND FAULT RELAY (GFR PADA RECLOSER DI SALURAN PENYULANG PENEBEL

Directory of Open Access Journals (Sweden)

I Dewa Gde Agung Budhi Udiana

2017-08-01

Full Text Available Short circuit causing over current problem and can might causing interference of the equipment performance such as distribution transformers also causing widespread disruption occurred. In resolving such interference is required as protection system on the distribution system. Seeing all above is needed coordination between the supporting component of the protection system which is consisted of Over Current Relay (OCR and Ground Fault Relay (GFR. The research was conducted at PT. PLN (Persero South Bali Area Network, INDONESIA on recloser in the feeder line of Penebel. OCR setting between the Relay feeder of Penebel, Recloser Celagi, Recloser Bakisan, and Recloser Benana still less selective, with time value coordination between average security was still less than 0,2 second. Then OCR setting and GFR relay feeder of Penebel, Recloser Celagi, Recloser Bakisan, and Recloser Benana was recommended for re-setting in order to minimize disruption and electric power distribution system to be reliable.

Two-way CSI-assisted AF relaying with HPA nonlinearity

KAUST Repository

Qi, Jian

2015-09-11

In this paper, we investigate half-duplex two-way dual-hop channel state information (CSI)-assisted amplify-andforward (AF) relaying in the presence of high-power amplifier (HPA) nonlinearity at relays. The expression for the end-toend signal-to-noise ratio (SNR) is derived as per the modified system model by taking into account the interference caused by relaying scheme and HPA nonlinearity. The system performance of the considered relaying network is evaluated in terms of average symbol error probability (SEP) in Nakagami-m fading channels, by making use of the moment-generating function (MGF) approach. Numerical results are provided and show the effects of several parameters, such as quadrature amplitude modulation (QAM) order, number of relays, HPA parameters, and Nakagami parameter, on performance. © 2015 IEEE.

Accurate measurement of {sup 3}J{sub HNHα} couplings in small or disordered proteins from WATERGATE-optimized TROSY spectra

Energy Technology Data Exchange (ETDEWEB)

Roche, Julien; Ying, Jinfa; Bax, Ad, E-mail: bax@nih.gov [National Institute of Diabetes and Digestive and Kidney Diseases, National Institutes of Health, Laboratory of Chemical Physics (United States)

2016-01-15

Provided that care is taken in adjusting the WATERGATE element of a {sup 1}H–{sup 15}N TROSY-HSQC experiment, such that neither the water magnetization nor the {sup 1}H{sup α} protons are inverted by its final 180° pulse, {sup 3}J{sub HNHα} couplings can be measured directly from splittings in the {sup 1}H dimension of the spectrum. With band-selective {sup 1}H decoupling, very high {sup 15}N resolution can be achieved. A complete set of {sup 3}J{sub HNHα} values, ranging from 3.4 to 10.1 Hz was measured for the 56-residue third domain of IgG-binding protein G (GB3). Using the H–N–C{sup α}–H{sup α} dihedral angles extracted from a RDC-refined structure of GB3, {sup 3}J{sub HNHα} values predicted by a previously parameterized Karplus equation agree to within a root-mean-square deviation (rmsd) of 0.37 Hz with the experimental data. Values measured for the Alzheimer’s implicated Aβ{sup 1−40} peptide fit to within an rmsd of 0.45 Hz to random coil {sup 3}J{sub HNHα} values.

Spreading Sequence System for Full Connectivity Relay Network

Science.gov (United States)

Kwon, Hyuck M. (Inventor); Yang, Jie (Inventor); Pham, Khanh D. (Inventor)

2018-01-01

Fully connected uplink and downlink fully connected relay network systems using pseudo-noise spreading and despreading sequences subjected to maximizing the signal-to-interference-plus-noise ratio. The relay network systems comprise one or more transmitting units, relays, and receiving units connected via a communication network. The transmitting units, relays, and receiving units each may include a computer for performing the methods and steps described herein and transceivers for transmitting and/or receiving signals. The computer encodes and/or decodes communication signals via optimum adaptive PN sequences found by employing Cholesky decompositions and singular value decompositions (SVD). The PN sequences employ channel state information (CSI) to more effectively and more securely computing the optimal sequences.

Four-Way Relaying in Wireless Cellular Systems

DEFF Research Database (Denmark)

Liu, Huaping; Popovski, Petar; De Carvalho, Elisabeth

2013-01-01

Two-way relaying in wireless systems has initiated a large research effort during the past few years. Nevertheless, it represents only a specific traffic pattern and it is of interest to investigate other traffic patterns where such a simultaneous processing of information flows can bring...... performance advantage. In this paper we consider a \\emph{four-way relaying} scenario, where each of the two Mobile Stations (MSs) has a two-way connection to the same Base Station (BS), while each connection is through a dedicated Relay Station (RS). The RSs are placed in such a way that one RS...... of the new scheme for Decode-and-Forward (DF) operational model for the RS. We compare the performance with a state-of-the-art reference scheme, based on two-way relaying with DF. The results indicate that the achievable rate regions are significantly enlarged for the new scheme....

Systematic Network Coding with the Aid of a Full-Duplex Relay

DEFF Research Database (Denmark)

Giacaglia, Giuliano; Shi, Xiaomeng; Kim, MinJi

2013-01-01

is to deliver a given number of data packets to a receiver with the aid of a relay. The source broadcasts to both the receiver and the relay using one frequency, while the relay uses another frequency for transmissions to the receiver, allowing for a full-duplex operation of the relay. We analyze the decoding...... complexity and delay performance of two types of relays: one that preserves the systematic structure of the code from the source; another that does not. A systematic relay forwards uncoded packets upon reception, but transmits coded packets to the receiver after receiving the first coded packet from...

Mobile User Connectivity in Relay-Assisted Visible Light Communications

Directory of Open Access Journals (Sweden)

Petr Pešek

2018-04-01

Full Text Available In this paper, we investigate relay-assisted visible light communications (VLC where a mobile user acts as a relay and forwards data from a transmitter to the end mobile user. We analyse the utilization of the amplify-and-forward (AF and decode-and-forward (DF relaying schemes. The focus of the paper is on analysis of the behavior of the mobile user acting as a relay while considering a realistic locations of the receivers and transmitters on a standard mobile phone, more specifically with two photodetectors on both sides of a mobile phone and a transmitting LED array located upright. We also investigate dependency of the bit error rate (BER performance on the azimuth and elevation angles of the mobile relay device within a typical office environment. We provide a new analytical description of BER for AF and DF-based relays in VLC. In addition we compare AF and DF-based systems and show that DF offers a marginal improvement in the coverage area with a BER < 10–3 and a data rate of 100 Mb/s. Numerical results also illustrate that relay-based systems offer a significant improvement in terms of the coverage compared to direct non-line of sight VLC links.

47 CFR 11.20 - State Relay Network.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false State Relay Network. 11.20 Section 11.20... Network. This network is composed of State Relay (SR) sources, leased common carrier communications facilities or any other available communication facilities. The network distributes State EAS messages...

SIMULASI SISTEM KELISTRIKAN KAMAR HOTEL MENGGUNAKAN SMART RELAY

Directory of Open Access Journals (Sweden)

I Nyoman Sukarma

2018-03-01

Full Text Available Fungsi dari alat key tag atau hotel switch atau key card adalah memutus atau menyambungkan aliran listrik ke dalam suatu area tertentu atau ruang. Key tag memiliki peran penting pada kamar hotel untuk mencegah pemborosan energi pada saat kamar hotel tidak berpenghuni atau belum tersewakan. Untuk itu, penulis merancang simulasi sistem kelistrikan pada kamar hotel yang dikontrol dengan smart relay. Pada simulasi ini digunakan smart relay Zelio Logic buatan Schneider Electric. Pemrograman smart relay ini menggunakan ladder diagram yang disusun menggunakan perangkat lunak ZelioSoft2 dari Schneider Electric. Smart relay menerima sinyal masukan dari sensor, key tag dan sakelar. Sinyal masukan tersebut selanjutnya diproses agar lampu, kotak-kontak, exhaust fan, dan AC (Air Conditioner pada kamar hotel dapat bekerja.

Performance of hybrid-ARQ with incremental redundancy over relay channels

KAUST Repository

Chelli, Ali; Alouini, Mohamed-Slim

2012-01-01

In this paper, we consider a relay network consisting of a source, a relay, and a destination. The source transmits a message to the destination using hybrid automatic repeat request (HARQ) with incremental redundancy (IR). The relay overhears

Asymptotic analysis for Nakagami-m fading channels with relay selection

KAUST Repository

Zhong, Caijun; Wong, Kaikit; Jin, Shi; Alouini, Mohamed-Slim; Ratnarajah, Tharm

2011-01-01

In this paper, we analyze the asymptotic outage probability performance of both decode-and-forward (DF) and amplify-and-forward (AF) relaying systems using partial relay selection and the "best" relay selection schemes for Nakagami-m fading channels

Efficient Resource Scheduling by Exploiting Relay Cache for Cellular Networks

Directory of Open Access Journals (Sweden)

Chun He

2015-01-01

Full Text Available In relay-enhanced cellular systems, throughput of User Equipment (UE is constrained by the bottleneck of the two-hop link, backhaul link (or the first hop link, and access link (the second hop link. To maximize the throughput, resource allocation should be coordinated between these two hops. A common resource scheduling algorithm, Adaptive Distributed Proportional Fair, only ensures that the throughput of the first hop is greater than or equal to that of the second hop. But it cannot guarantee a good balance of the throughput and fairness between the two hops. In this paper, we propose a Two-Hop Balanced Distributed Scheduling (TBS algorithm by exploiting relay cache for non-real-time data traffic. The evolved Node Basestation (eNB adaptively adjusts the number of Resource Blocks (RBs allocated to the backhaul link and direct links based on the cache information of relays. Each relay allocates RBs for relay UEs based on the size of the relay UE’s Transport Block. We also design a relay UE’s ACK feedback mechanism to update the data at relay cache. Simulation results show that the proposed TBS can effectively improve resource utilization and achieve a good trade-off between system throughput and fairness by balancing the throughput of backhaul and access link.

Wireless Energy Harvesting Two-Way Relay Networks with Hardware Impairments.

Science.gov (United States)

Peng, Chunling; Li, Fangwei; Liu, Huaping

2017-11-13

This paper considers a wireless energy harvesting two-way relay (TWR) network where the relay has energy-harvesting abilities and the effects of practical hardware impairments are taken into consideration. In particular, power splitting (PS) receiver is adopted at relay to harvests the power it needs for relaying the information between the source nodes from the signals transmitted by the source nodes, and hardware impairments is assumed suffered by each node. We analyze the effect of hardware impairments [-20]on both decode-and-forward (DF) relaying and amplify-and-forward (AF) relaying networks. By utilizing the obtained new expressions of signal-to-noise-plus-distortion ratios, the exact analytical expressions of the achievable sum rate and ergodic capacities for both DF and AF relaying protocols are derived. Additionally, the optimal power splitting (OPS) ratio that maximizes the instantaneous achievable sum rate is formulated and solved for both protocols. The performances of DF and AF protocols are evaluated via numerical results, which also show the effects of various network parameters on the system performance and on the OPS ratio design.

Two-Way Multi-Antenna Relaying with Simultaneous Wireless Information and Power Transfer

Directory of Open Access Journals (Sweden)

Thanaphat Srivantana

2017-03-01

Full Text Available In this paper, we propose various kinds of two-way multi-antenna relaying with simultaneous wireless information and power transfer (SWIPT and investigate their performance. Specifically, we first consider a two-way relay network where two single-antenna end nodes communicate with each other through a multi-antenna relay node that is energy constrained. This relay node harvests energy from the two end nodes and use the harvested energy for forwarding their information. Six relaying schemes that support the considered network then build on the power splitting-based relaying and time switching-based relaying protocols. The average bit error rates of these schemes are evaluated and compared by computer simulations considering several network parameters, including the number of relay antennas, power splitting ratio, and energy harvesting time. Such evaluation and comparison provide useful insights into the performance of SWIPT-based two-way multi-antenna relaying.

Developing a Domain Model for Relay Circuits

DEFF Research Database (Denmark)

Haxthausen, Anne Elisabeth

2009-01-01

In this paper we stepwise develop a domain model for relay circuits as used in railway control systems. First we provide an abstract, property-oriented model of networks consisting of components that can be glued together with connectors. This model is strongly inspired by a network model...... for railways madeby Bjørner et.al., however our model is more general: the components can be of any kind and can later be refined to e.g. railway components or circuit components. Then we show how the abstract network model can be refined into an explicit model for relay circuits. The circuit model describes...... the statics as well as the dynamics of relay circuits, i.e. how a relay circuit can be composed legally from electrical components as well as how the components may change state over time. Finally the circuit model is transformed into an executable model, and we show how a concrete circuit can be defined...

Proton-proton elastic scattering measurements at COSY

Energy Technology Data Exchange (ETDEWEB)

Bagdasarian, Zara [Forschungszentrum Juelich, Juelich (Germany); Tbilisi State University, Tbilisi (Georgia); Collaboration: ANKE-Collaboration

2014-07-01

To construct the reliable phase shift analysis (PSA) that can successfully describe the nucleon-nucleon (NN) interaction it is necessary to measure variety of experimental observables for both proton-proton (pp) and neutron-proton (np) elastic scattering. The polarized beams and targets at COSY-ANKE facility allow a substantial contribution to the existing database. The experiment was carried out in April 2013 at ANKE using a transversely polarized proton beam incident on an unpolarized hydrogen cluster target. Six beam energies of T{sub p}=0.8,1.6,1.8,2.0,2.2,2.4 GeV were used. The aim of this talk is to present the preliminary results for the analyzing power (A{sub y}) for the pp elastic scattering in the so-far unexplored 5 <θ{sub cm}<30 angular range. Our measurements are also compared to the world data and current partial wave solutions.

An RSS based location estimation technique for cognitive relay networks

KAUST Repository

Qaraqe, Khalid A.; Hussain, Syed Imtiaz; Ç elebi, Hasari Burak; Abdallah, Mohamed M.; Alouini, Mohamed-Slim

2010-01-01

In this paper, a received signal strength (RSS) based location estimation method is proposed for a cooperative wireless relay network where the relay is a cognitive radio. We propose a method for the considered cognitive relay network to determine

Breaking the Myth That Relay Swimming Is Faster Than Individual Swimming.

Science.gov (United States)

Skorski, Sabrina; Etxebarria, Naroa; Thompson, Kevin G

2016-04-01

To investigate if swimming performance is better in a relay race than in the corresponding individual race. The authors analyzed 166 elite male swimmers from 15 nations in the same competition (downloaded from www.swimrankings.net). Of 778 observed races, 144 were Olympic Games performances (2000, 2004, 2012), with the remaining 634 performed in national or international competitions. The races were 100-m (n = 436) and 200-m (n = 342) freestyle events. Relay performance times for the 2nd-4th swimmers were adjusted (+ 0.73 s) to allow for the "flying start." Without any adjustment, mean individual relay performances were significantly faster for the first 50 m and overall time in the 100-m events. Furthermore, the first 100 m of the 200-m relay was significantly faster (P > .001). During relays, swimmers competing in 1st position did not show any difference compared with their corresponding individual performance (P > .16). However, swimmers competing in 2nd-4th relay-team positions demonstrated significantly faster times in the 100-m (P individual events (P team positions were adjusted for the flying start no differences were detected between relay and individual race performance for any event or split time (P > .17). Highly trained swimmers do not swim (or turn) faster in relay events than in their individual races. Relay exchange times account for the difference observed in individual vs relay performance.

Scalable DeNoise-and-Forward in Bidirectional Relay Networks

DEFF Research Database (Denmark)

Sørensen, Jesper Hemming; Krigslund, Rasmus; Popovski, Petar

2010-01-01

In this paper a scalable relaying scheme is proposed based on an existing concept called DeNoise-and-Forward, DNF. We call it Scalable DNF, S-DNF, and it targets the scenario with multiple communication flows through a single common relay. The idea of the scheme is to combine packets at the relay...... in order to save transmissions. To ensure decodability at the end-nodes, a priori information about the content of the combined packets must be available. This is gathered during the initial transmissions to the relay. The trade-off between decodability and number of necessary transmissions is analysed...

Sum-Rate Maximization of Coordinated Direct and Relay Systems

DEFF Research Database (Denmark)

Sun, Fan; Popovski, Petar; Thai, Chan

2012-01-01

Joint processing of multiple communication flows in wireless systems has given rise to a number of novel transmission techniques, notably the two-way relaying based on wireless network coding. Recently, a related set of techniques has emerged, termed coordinated direct and relay (CDR) transmissions......, where the constellation of traffic flows is more general than the two-way. Regardless of the actual traffic flows, in a CDR scheme the relay has a central role in managing the interference and boosting the overall system performance. In this paper we investigate the novel transmission modes, based...... on amplify-and-forward, that arise when the relay is equipped with multiple antennas and can use beamforming. We focus on one representative traffic type, with one uplink and one downlink users and consider the achievable sum-rate maximization relay beamforming. The beamforming criterion leads to a non...

Effects of relay chatter in seismic probabilistic safety analysis

International Nuclear Information System (INIS)

Reed, J.W.; Shiu, K.K.

1985-01-01

In the Zion and Indian Point Probabilistic Safety Studies, relay chatter was dismissed as a credible event and hence was not formally included in the analyses. Although little discussion is given in the Zion and Indian Point PSA documentation concerning the basis for this decision, it has been expressed informally that it was assumed that the operators will be able to reset all relays in a timely manner. Currently, it is the opinion of many professionals that this may be an oversimplification. The three basic areas which must be considered in addressing relay chatter include the fragility of the relays per se, the reliability of the operators to reset the relays and finally the systems response aspects. Each of these areas is reviewed and the implications for seismic PSA are discussed. Finally, recommendations for future research are given

Relay communications strategies for Mars exploration through 2020

Science.gov (United States)

Edwards, Charles D., Jr.; Arnold, B.; DePaula, R.; Kazz, G.; Lee, C.; Noreen, G.

2005-01-01

In this paper we will examine NASA's strategy for relay communications support of missions planned for this decade, and discuss options for longer-term relay network evolution in support of second-decade missions.

76 FR 65965 - Contributions to the Telecommunications Relay Services Fund

Science.gov (United States)

2011-10-25

...] Contributions to the Telecommunications Relay Services Fund AGENCY: Federal Communications Commission. ACTION... Telecommunications Relay Services (TRS) Fund in a manner prescribed by regulation that is consistent with and... . SUPPLEMENTARY INFORMATION: This is a summary of the Commission's Contributions to the Telecommunications Relay...

Switched diversity strategies for dual-hop relaying systems

KAUST Repository

Gaaloul, Fakhreddine; Alouini, Mohamed-Slim; Radaydeh, Redha M.

2011-01-01

This paper investigates the effect of different switched diversity configurations on the implementation complexity and achieved performance of dual-hop amplify-and-forward (AF) relaying networks. A low-complexity model of the relay station

ANKE, a new facility for medium energy hadron physics at COSY-Juelich

International Nuclear Information System (INIS)

Barsov, S.; Bechstedt, U.; Bothe, W.; Bongers, N.; Borchert, G.; Borgs, W.; Braeutigam, W.; Buescher, M.; Cassing, W.; Chernyshev, V.; Chiladze, B.; Dietrich, J.; Drochner, M.; Dymov, S.; Erven, W.; Esser, R.; Franzen, A.; Golubeva, Ye.; Gotta, D.; Grande, T.; Grzonka, D.; Hardt, A.; Hartmann, M.; Hejny, V.; Horn, L. van; Jarczyk, L.; Junghans, H.; Kacharava, A.; Kamys, B.; Khoukaz, A.; Kirchner, T.; Klehr, F.; Klein, W.; Koch, H.R.; Komarov, V.I.; Kondratyuk, L.; Koptev, V.; Kopyto, S.; Krause, R.; Kravtsov, P.; Kruglov, V.; Kulessa, P.; Kulikov, A.; Lang, N.; Langenhagen, N.; Lepges, A.; Ley, J.; Maier, R.; Martin, S.; Macharashvili, G.; Merzliakov, S.; Meyer, K.; Mikirtychiants, S.; Mueller, H.; Munhofen, P.; Mussgiller, A.; Nekipelov, M.; Nelyubin, V.; Nioradze, M.; Ohm, H.; Petrus, A.; Prasuhn, D.; Prietzschk, B.; Probst, H.J.; Pysz, K.; Rathmann, F.; Rimarzig, B.; Rudy, Z.; Santo, R.; Paetz Schieck, H.; Schleichert, R.; Schneider, A.; Schneider, Chr.; Schneider, H.; Schwarz, U.; Seyfarth, H.; Sibirtsev, A.; Sieling, U.; Sistemich, K.; Selikov, A.; Stechemesser, H.; Stein, H.J.; Strzalkowski, A.; Watzlawik, K.-H.; Wuestner, P.; Yashenko, S.; Zalikhanov, B.; Zhuravlev, N.; Zwoll, K.; Zychor, I.; Schult, O.W.B.; Stroeher, H.

2001-01-01

ANKE is a new experimental facility for the spectroscopy of products from proton-induced reactions on internal targets. It has recently been implemented in the accelerator ring of the cooler synchrotron COSY of the Forschungszentrum Juelich (FZ-Juelich), Germany. The device consists of three dipole magnets, various target installations and dedicated detection systems. It will enable a variety of hadron-physics experiments like meson production in elementary proton-nucleon processes and studies of medium modifications in proton-nucleus interactions

Relay selection in underlay cognitive networks with fixed transmission power nodes

KAUST Repository

Hussain, Syed Imtiaz

2013-07-31

Underlay cognitive networks operate simultaneously with primary networks satisfying stringent interference constraints, which reduces their transmission power and coverage area. To reach remote destinations, secondary sources use relaying techniques. Selecting the best relay among the available ones is a well known technique. Recently, selective cooperation is investigated in cognitive networks where the secondary nodes can adapt their transmission power to always satisfy the interference threshold. In this paper, we investigate a situation where the secondary nodes have a fixed transmission power and may violate the interference threshold. We present two relay selection schemes; the first one excludes the relays not satisfying the interference constraint and then picks up a relay from the remaining ones that can provide the maximum signal-to-noise ratio (SNR). The other scheme uses a quotient of the relay link SNR and the interference from the relay to the primary user and optimizes it to maximise the relay link SNR. We derive closed form expressions for outage probability, bit error rate, channel capacity and diversity of the system for both schemes by using tight approximations. We also study mutual effects of interference. Simulation results confirm the analytical results and reveal that the relay selection is feasible at low SNRs. Copyright © 2013 John Wiley & Sons, Ltd.

Bilayer Protograph Codes for Half-Duplex Relay Channels

Science.gov (United States)

Divsalar, Dariush; VanNguyen, Thuy; Nosratinia, Aria

2013-01-01

Direct to Earth return links are limited by the size and power of lander devices. A standard alternative is provided by a two-hops return link: a proximity link (from lander to orbiter relay) and a deep-space link (from orbiter relay to Earth). Although direct to Earth return links are limited by the size and power of lander devices, using an additional link and a proposed coding for relay channels, one can obtain a more reliable signal. Although significant progress has been made in the relay coding problem, existing codes must be painstakingly optimized to match to a single set of channel conditions, many of them do not offer easy encoding, and most of them do not have structured design. A high-performing LDPC (low-density parity-check) code for the relay channel addresses simultaneously two important issues: a code structure that allows low encoding complexity, and a flexible rate-compatible code that allows matching to various channel conditions. Most of the previous high-performance LDPC codes for the relay channel are tightly optimized for a given channel quality, and are not easily adapted without extensive re-optimization for various channel conditions. This code for the relay channel combines structured design and easy encoding with rate compatibility to allow adaptation to the three links involved in the relay channel, and furthermore offers very good performance. The proposed code is constructed by synthesizing a bilayer structure with a pro to graph. In addition to the contribution to relay encoding, an improved family of protograph codes was produced for the point-to-point AWGN (additive white Gaussian noise) channel whose high-rate members enjoy thresholds that are within 0.07 dB of capacity. These LDPC relay codes address three important issues in an integrative manner: low encoding complexity, modular structure allowing for easy design, and rate compatibility so that the code can be easily matched to a variety of channel conditions without extensive

Implementation of a Relay Coordination System for the Mars Network

Science.gov (United States)

Allard, Daniel A.

2010-01-01

Mars network relay operations involve the coordination of lander and orbiter teams through long-term and short-term planning, tactical changes and post-pass analysis. Much of this coordination is managed through email traffic and point-to-point file data exchanges. It is often difficult to construct a complete and accurate picture of the relay situation at any given moment, as there is no centralized store of correlated relay data. The Mars Relay Operations Service (MaROS) is being implemented to address the problem of relay coordination for current and next-generation relay missions. The service is provided for the purpose of coordinating communications sessions between landed spacecraft assets and orbiting spacecraft assets at Mars. The service centralizes a set of functions previously distributed across multiple spacecraft operations teams, and as such greatly improves visibility into the end-to-end strategic coordination process. Most of the process revolves around the scheduling of communications sessions between the spacecraft during periods of time when a landed asset on Mars is geometrically visible by an orbiting spacecraft. These "relay" sessions are used to transfer data both to and from the landed asset via the orbiting asset on behalf of Earth-based spacecraft operators. This paper will discuss the relay coordination problem space, overview the architecture and design selected to meet system requirements, and describe the first phase of system implementation

Screening test of relays used under pressurized sulfur hexafluoride (SF6)

International Nuclear Information System (INIS)

Kutsukake, Kenichi; Matsuda, Makoto; Hanashima, Susumu; Obara, Kenjiro

2008-01-01

Many measurement and control devices inside of a high voltage terminal of the JAEA-Tokai tandem accelerator are operated under pressurized sulfur hexafluoride gas (SF 6 ) of 0.5 MPa. This screening test has been carried out to select a relay, which is usable under the pressurized SF 6 for turn on and off a large current of the devices, from commercial relays used in the atmospheric condition. Four kinds of relays were tested: electromechanical relay (EMR), magnet contactor (MAG), solid-state relay (SSR) and hybrid relay (HYB). Temperature and appearance changes of the relay were collected as measurement items. In addition, a reason of contact trouble of the relays was considered from the results of qualitative elementary analysis and observation of the contact surface using the EDS (energy-dispersive X-ray spectroscopy) and the SEM (scanning electron microscope). As a result, the EMR and the MAG showed irregular contact in spite of input voltage and electric current had fed to an operational coil of the relay normally. It is caused by the sulfide or fluoride compounds, which were formed by chemical reaction between metals and sulfur or hydrogen fluoride due to dissociation of SF 6 in electric arcs. On the other hand, the performance of the SSR and the HYB is better than the EMR and the MAG, and it was found that these relays are available in the pressurized SF 6 of 0.5MPa in spite of the standard specification. (author)

Relay-based information broadcast in complex networks

Science.gov (United States)

Fan, Zhongyan; Han, Zeyu; Tang, Wallace K. S.; Lin, Dong

2018-04-01

Information broadcast (IB) is a critical process in complex network, usually accomplished by flooding mechanism. Although flooding is simple and no prior topological information is required, it consumes a lot of transmission overhead. Another extreme is the tree-based broadcast (TB), for which information is disseminated via a spanning tree. It achieves the minimal transmission overhead but the maintenance of spanning tree for every node is an obvious obstacle for implementation. Motivated by the success of scale-free network models for real-world networks, in this paper, we investigate the issues in IB by considering an alternative solution in-between these two extremes. A novel relay-based broadcast (RB) mechanism is proposed by employing a subset of nodes as relays. Information is firstly forwarded to one of these relays and then re-disseminated to others through the spanning tree whose root is the relay. This mechanism provides a trade-off solution between flooding and TB. On one hand, it saves up a lot of transmission overhead as compared to flooding; on the other hand, it costs much less resource for maintenance than TB as only a few spanning trees are needed. Based on two major criteria, namely the transmission overhead and the convergence time, the effectiveness of RB is confirmed. The impacts of relay assignment and network structures on performance are also studied in this work.

Cooperative relay-based multicasting for energy and delay minimization

KAUST Repository

Atat, Rachad

2012-08-01

Relay-based multicasting for the purpose of cooperative content distribution is studied. Optimized relay selection is performed with the objective of minimizing the energy consumption or the content distribution delay within a cluster of cooperating mobiles. Two schemes are investigated. The first consists of the BS sending the data only to the relay, and the second scheme considers the scenario of threshold-based multicasting by the BS, where a relay is selected to transmit the data to the mobiles that were not able to receive the multicast data. Both schemes show significant superiority compared to the non-cooperative scenarios, in terms of energy consumption and delay reduction. © 2012 IEEE.

Results from EDDA at COSY: Spin Observables in Proton-Proton Elastic Scattering

International Nuclear Information System (INIS)

Rohdjess, Heiko

2003-01-01

Elastic proton-proton scattering as one of the fundamental hadronic reactions has been studied with the internal target experiment EDDA at the Cooler-Synchrotron COSY/Juelich. A precise measurement of differential cross section, analyzing power and three spin-correlation parameters over a large angular (θc.m. ≅ 35 deg. - 90 deg.) and energy (Tp ≅ 0.5 - 2.5 GeV) range has been carried out in the past years. By taking scattering data during the acceleration of the COSY beam, excitation functions were measured in small energy steps and consistent normalization with respect to luminosity and polarization. The experiment uses internal fiber targets and a polarized hydrogen atomic-beam target in conjunction with a double-layered, cylindrical scintillator hodoscope for particle detection. The results on differential cross sections and analyzing powers have been published and helped to improve phase shift solutions. Recently data taking with polarized beam and target has been completed. Preliminary results for the spin-correlation parameters A NN, ASS, and ASL are presented. The observable ASS has been measured the first time above 800 MeV and our results are in sharp contrast to phase-shift predictions at higher energies. Our analysis shows that some of the ambiguities in the direct reconstruction of scattering amplitudes which also show up as differences between available phase-shift solutions, will be reduced by these new measurements

Secure relay selection based on learning with negative externality in wireless networks

Science.gov (United States)

Zhao, Caidan; Xiao, Liang; Kang, Shan; Chen, Guiquan; Li, Yunzhou; Huang, Lianfen

2013-12-01

In this paper, we formulate relay selection into a Chinese restaurant game. A secure relay selection strategy is proposed for a wireless network, where multiple source nodes send messages to their destination nodes via several relay nodes, which have different processing and transmission capabilities as well as security properties. The relay selection utilizes a learning-based algorithm for the source nodes to reach their best responses in the Chinese restaurant game. In particular, the relay selection takes into account the negative externality of relay sharing among the source nodes, which learn the capabilities and security properties of relay nodes according to the current signals and the signal history. Simulation results show that this strategy improves the user utility and the overall security performance in wireless networks. In addition, the relay strategy is robust against the signal errors and deviations of some user from the desired actions.

Proof-of-Work as Anonymous Micropayment: Rewarding a Tor Relay

OpenAIRE

Biryukov, Alex; Pustogarov, Ivan

2015-01-01

In this paper we propose a new micropayments scheme which can be used to reward Tor relay operators. Tor clients do not pay Tor relays with electronic cash directly but submit proof of work shares which the relays can resubmit to a crypto-currency mining pool. Relays credit users who submit shares with tickets that can later be used to purchase improved service. Both shares and tickets when sent over Tor circuits are anonymous. The analysis of the crypto-currencies market prices shows that th...

Error-rate performance analysis of opportunistic regenerative relaying

KAUST Repository

Tourki, Kamel

2011-09-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path can be considered unusable, and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We first derive the exact statistics of each hop, in terms of probability density function (PDF). Then, the PDFs are used to determine accurate closed form expressions for end-to-end bit-error rate (BER) of binary phase-shift keying (BPSK) modulation where the detector may use maximum ration combining (MRC) or selection combining (SC). Finally, we validate our analysis by showing that performance simulation results coincide with our analytical results over linear network (LN) architecture and considering Rayleigh fading channels. © 2011 IEEE.

An RSS based location estimation technique for cognitive relay networks

KAUST Repository

Qaraqe, Khalid A.

2010-11-01

In this paper, a received signal strength (RSS) based location estimation method is proposed for a cooperative wireless relay network where the relay is a cognitive radio. We propose a method for the considered cognitive relay network to determine the location of the source using the direct and the relayed signal at the destination. We derive the Cramer-Rao lower bound (CRLB) expressions separately for x and y coordinates of the location estimate. We analyze the effects of cognitive behaviour of the relay on the performance of the proposed method. We also discuss and quantify the reliability of the location estimate using the proposed technique if the source is not stationary. The overall performance of the proposed method is presented through simulations. ©2010 IEEE.

CERN’s annual relay a runaway success

CERN Document Server

Klaus Hanke for the CERN Running Club

2016-01-01

With a record participation of 128 teams of six runners each, this year’s CERN Relay Race took place on 19 May on the Meyrin site.   One of the many winning teams from the 2016 relay race. (Image: Sophia Bennett/CERN) With a record participation of 128 teams and 768 runners, this year’s CERN Relay Race took place on 19 May on the Meyrin site. The teams were mainly composed of CERN staff or contractors working on the CERN site.  A few external teams took also part in the race. Times ranged from 10 min 19 s to over 18 min. The Running Club website now has both the results, and the photos from race day. The CERN Relay Race is jointly organised every year by the CERN Running Club and the Staff Association. It is a tradition that is appreciated by many as a team building, rather than a competitive event. The CERN Running Club wishes to thank all runners and all volunteers for making this event a success.

Securing Relay Networks with Artificial Noise: An Error Performance-Based Approach

Directory of Open Access Journals (Sweden)

Ying Liu

2017-07-01

Full Text Available We apply the concept of artificial and controlled interference in a two-hop relay network with an untrusted relay, aiming at enhancing the wireless communication secrecy between the source and the destination node. In order to shield the square quadrature amplitude-modulated (QAM signals transmitted from the source node to the relay, the destination node designs and transmits artificial noise (AN symbols to jam the relay reception. The objective of our considered AN design is to degrade the error probability performance at the untrusted relay, for different types of channel state information (CSI at the destination. By considering perfect knowledge of the instantaneous CSI of the source-to-relay and relay-to-destination links, we first present an analytical expression for the symbol error rate (SER performance at the relay. Based on the assumption of an average power constraint at the destination node, we then derive the optimal phase and power distribution of the AN that maximizes the SER at the relay. Furthermore, we obtain the optimal AN design for the case where only statistical CSI is available at the destination node. For both cases, our study reveals that the Gaussian distribution is generally not optimal to generate AN symbols. The presented AN design takes into account practical parameters for the communication links, such as QAM signaling and maximum likelihood decoding.

Recent results from the NN-interaction studies with polarized beams and targets at ANKE-COSY

Science.gov (United States)

Dymov, Sergey

2016-02-01

Adding to the nucleon-nucleon scattering database is one of the major priorities of the ANKE collaboration. Such data are necessary ingredients, not only for the understanding of nuclear forces, but also for the description of meson production and other nuclear reactions at intermediate energies. By measuring the cross section, deuteron analysing powers, and spin-correlation parameters in the dp → {pp}sn reaction, where {pp}s represents the 1S0 state, information has been obtained on small-angle neutron-proton spin-flip charge-exchange amplitudes. The measurements of pp elastic scattering by the COSY-EDDA have had a major impact on the partial wave analysis of this reaction above 1 GeV. However, these experiments only extended over the central region of c.m. angles, 300 < θcm < 1500, that has left major ambiguities in the phase shift analysis by the SAID group. In contrast, the small angle region is accessible at ANKE-COSY, that allowed measurement of the differential cross section and the analysing power at 50 < θcm < 300 in the 0.8 — 2.8 GeV energy range. The data on the pn elastic scattering are much more scarce than those of pp, especially in the region above 1.15 GeV. The study of the dp → {pp}s n reaction provides the information about the pn elastic scattering at large angles. The small angle scattering was studied with the polarized proton COSY beam and an unpolarised deuterium gas target. The detection the spectator proton in the ANKE vertex silicon detector allowed to use the deuterium target as an effective neutron one. The analysing powers of the process were obtained at six beam energies from 0.8 to 2.4 GeV.

Efficient incremental relaying for packet transmission over fading channels

KAUST Repository

Fareed, Muhammad Mehboob

2014-07-01

In this paper, we propose a novel relaying scheme for packet transmission over fading channels, which improves the spectral efficiency of cooperative diversity systems by utilizing limited feedback from the destination. Our scheme capitalizes on the fact that relaying is only required when direct transmission suffers deep fading. We calculate the packet error rate for the proposed efficient incremental relaying (EIR) scheme with both amplify and forward and decode and forward relaying. We compare the performance of the EIR scheme with the threshold-based incremental relaying (TIR) scheme. It is shown that the efficiency of the TIR scheme is better for lower values of the threshold. However, the efficiency of the TIR scheme for higher values of threshold is outperformed by the EIR. In addition, three new threshold-based adaptive EIR are devised to further improve the efficiency of the EIR scheme. We calculate the packet error rate and the efficiency of these new schemes to provide the analytical insight. © 2014 IEEE.

Relay discovery and selection for large-scale P2P streaming.

Directory of Open Access Journals (Sweden)

Chengwei Zhang

Full Text Available In peer-to-peer networks, application relays have been commonly used to provide various networking services. The service performance often improves significantly if a relay is selected appropriately based on its network location. In this paper, we studied the location-aware relay discovery and selection problem for large-scale P2P streaming networks. In these large-scale and dynamic overlays, it incurs significant communication and computation cost to discover a sufficiently large relay candidate set and further to select one relay with good performance. The network location can be measured directly or indirectly with the tradeoffs between timeliness, overhead and accuracy. Based on a measurement study and the associated error analysis, we demonstrate that indirect measurements, such as King and Internet Coordinate Systems (ICS, can only achieve a coarse estimation of peers' network location and those methods based on pure indirect measurements cannot lead to a good relay selection. We also demonstrate that there exists significant error amplification of the commonly used "best-out-of-K" selection methodology using three RTT data sets publicly available. We propose a two-phase approach to achieve efficient relay discovery and accurate relay selection. Indirect measurements are used to narrow down a small number of high-quality relay candidates and the final relay selection is refined based on direct probing. This two-phase approach enjoys an efficient implementation using the Distributed-Hash-Table (DHT. When the DHT is constructed, the node keys carry the location information and they are generated scalably using indirect measurements, such as the ICS coordinates. The relay discovery is achieved efficiently utilizing the DHT-based search. We evaluated various aspects of this DHT-based approach, including the DHT indexing procedure, key generation under peer churn and message costs.

Mimicking the membrane-mediated conformation of dynorphin A-(1-13)-peptide: Circular dichroism and nuclear magnetic resonance studies in methanolic solution

International Nuclear Information System (INIS)

Lancaster, C.R.D.; Hughes, D.W.; Epand, R.M.; Mishra, P.K.; Bothner-By, A.A.; St Pierre, S.A.

1991-01-01

The structural requirements for the binding of dynorphin to the κ-opioid receptor are of profound clinical interest in the search for a powerful nonaddictive analgesic. These requirements are thought to be met by the membrane-mediated conformation of the opioid peptide dynorphin A-(1-13)-peptide, Tyr 1 -Gly 2 -Gly 3 -Phe 4 -Leu 5 -Arg 6 -Arg 7 -Ile 8 -Arg 9 -Pro 10 -Lys 11 -Leu 12 -Lys 13 . Schwyzer has proposed an essentially α-helical membrane-mediated conformation of the 13 amino acid peptide. In the present study, circular dichroism (CD) studies on dynorphin A-(1-13)-peptide bound to an anionic phospholipid signified negligible helical content of the peptide. CD studies also demonstrated that the aqueous-membraneous interphase may be mimicked by methanol. The 500- and 620-MHz 1 H nuclear magnetic resonance (NMR) spectra of dynorphin A-(1-13)-peptide in methanolic solution were sequence-specifically assigned with the aid of correlated spectroscopy (COSY), double-quantum filtered phase-sensitive COSY (DQF-COSY), relayed COSY (RELAY), and nuclear Overhauser enhancement spectroscopy (NOESY). 2-D CAMELSPIN/ROESY experiments indicated that at least the part of the molecule from Arg 7 to Arg 9 was in an extended or β-strand conformation, which agreed with deuterium-exchange and temperature-dependence studies of the amide protons and analysis of the vicinal spin-spin coupling constants 3 J HNα . The results clearly demonstrated the absence of extensive α-helix formation. χ 1 rotamer analysis of the 3 J αβ demonstrated no preferred side-chain conformations

Feasibility study of the {eta}'{yields} {pi}{sup +} {pi}{sup -} {pi}{sup 0} decay using WASA-at-COSY apparatus

Energy Technology Data Exchange (ETDEWEB)

Zielinski, M.

2008-07-15

One of the objectives of the vast physics programme of the recently commissioned WASA-at-COSY facility is the study of fundamental symmetries via the measurements of the {eta} and {eta}' mesons decays. Especially interesting are isospin violating hadronic precesses of these mesons into 3{pi} systems driven by the term of QCD Lagrangian which depends on the mass difference of the u and d quarks. When an {eta} or an {eta}' meson is created in the hadronic reaction signals from such decays may be significantly obscured by the prompt production of {pi} mesons. In this thesis we present the estimation of the upper limit of the background due to prompt pion production for the {eta}'{yields}3{pi}{sup 0} and {eta}'{yields}{pi}{sup +}{pi}{sup -}{pi}{sup 0} decays. Using the data from proton-proton collisions measured by the COSY-11 group we have extracted differential cross sections for the multimeson production with the invariant mass corresponding to the mass of the {eta}' meson. Based on these results and on parametrizations of the total cross sections for the {eta}' meson as well as parametrization of the upper limit for the prompt pi{sup +}pi{sup -}pi{sup 0} production in the collisions of protons we discuss in details the feasibility of a measurement of the {eta}' meson decay into 3{pi} channels with the WASA-at-COSY facility. Based on the chiral unitary approach the value of the branching ratio BR({eta}'{yields}{pi}{sup +}{pi}{sup -}{pi}{sup 0}) was recently predicted to be about 1%. We show that the WASA-at-COSY has a potential to verify this result empirically. (orig.)

Optimal Coordination of Distance and Directional Overcurrent Relays Considering Different Network Topologies

OpenAIRE

Y. Damchi; J. Sadeh; H. Rajabi Mashhadi

2015-01-01

Most studies in relay coordination have focused solely on coordination of overcurrent relays while distance relays are used as the main protection of transmission lines. Since, simultaneous coordination of these two types of relays can provide a better protection, in this paper, a new approach is proposed for simultaneous coordination of distance and directional overcurrent relays (D&DOCRs). Also, pursued by most of the previously published studies, the settings of D&DOCRs are usually determi...

Microcomputer relay regulator in the CAMAC standard

International Nuclear Information System (INIS)

Nikolaev, V.P.

1984-01-01

The digital relay regulator is developed on the base of the KM001 microcomputer and KK06 controller for automatic control ob ects with transfer functions describing a broad class of systems using actuating motors (stabilitation, follow-up systems). The CAMAC relay-unit realizes the regulation law and provides the possibility to control analogous values by 8 channels

Coordination of Regenerative Relays and Direct Users in Wireless Cellular Networks

DEFF Research Database (Denmark)

Thai, Chan; Popovski, Petar

2011-01-01

The area of wireless cooperation/relaying has recently been significantly enriched by the ideas of wireless network coding (NC), which bring substantial gains in spectral efficiency. These gains have mainly been demonstrated in scenarios with two-way relaying. Inspired by the ideas of wireless NC......, recently we have proposed techniques for coordinated direct/relay (CDR) transmissions. These techniques embrace the interference among the communication flows to/from direct and relayed users, leveraging on the fact that the interference can be subsequently canceled. Hence, by allowing simultaneous...... transmissions, spectral efficiency is increased. In our prior work, we have considered CDR with non-regenerative relay that uses Amplify-and-Forward (AF). In this paper we consider the case of regenerative Decode-and-Forward (DF) relay. This refers also to joint decoding of the interfering flows received over...

Effects of alloying on Co--Si eutectoid structures and properties

International Nuclear Information System (INIS)

Livingston, J.D.

1976-01-01

The effects of various ternary alloying elements on the microstructure and properties of directionally solidified and transformed Co-Si eutectoid alloys were studied. Aligned eutectoid structures were maintained with additions of up to 10 at. percent Ni. However, higher Ni additions led to changes in both the silicide and solid-solution phases, related changes in microstructure, and decreased tensile strength. Additions of 5 at. percent Cr, Cu, Fe, or Mn produced cellular eutectoid microstructures which deteriorated the mechanical properties. Additions of W, Ta, or Al led to eutectic, rather than eutectoid, microstructures. Alloys based on the Co-W-Si eutectic appear to have the most promising high-temperature mechanical properties

Admission Control Threshold in Cellular Relay Networks with Power Adjustment

Directory of Open Access Journals (Sweden)

Lee Ki-Dong

2009-01-01

Full Text Available Abstract In the cellular network with relays, the mobile station can benefit from both coverage extension and capacity enhancement. However, the operation complexity increases as the number of relays grows up. Furthermore, in the cellular network with cooperative relays, it is even more complex because of an increased dimension of signal-to-noise ratios (SNRs formed in the cooperative wireless transmission links. In this paper, we propose a new method for admission capacity planning in a cellular network using a cooperative relaying mechanism called decode-and-forward. We mathematically formulate the dropping ratio using the randomness of "channel gain." With this, we formulate an admission threshold planning problem as a simple optimization problem, where we maximize the accommodation capacity (in number of connections subject to two types of constraints. (1 A constraint that the sum of the transmit powers of the source node and relay node is upper-bounded where both nodes can jointly adjust the transmit power. (2 A constraint that the dropping ratio is upper-bounded by a certain threshold value. The simplicity of the problem formulation facilitates its solution in real-time. We believe that the proposed planning method can provide an attractive guideline for dimensioning a cellular relay network with cooperative relays.

Implementation of a microcomputer based distance relay for parallel transmission lines

International Nuclear Information System (INIS)

Phadke, A.G.; Jihuang, L.

1986-01-01

Distance relaying for parallel transmission lines is a difficult application problem with conventional phase and ground distance relays. It is known that for cross-country faults involving dissimilar phases and ground, three phase tripping may result. This paper summarizes a newly developed microcomputer based relay which is capable of classifying the cross-country fault correctly. The paper describes the principle of operation and results of laboratory tests of this relay

Performance Analysis of Selective Decode-and-Forward Multinode Incremental Relaying with Maximal Ratio Combining

KAUST Repository

Hadjtaieb, Amir

2013-09-12

In this paper, we propose an incremental multinode relaying protocol with arbitrary N-relay nodes that allows an efficient use of the channel spectrum. The destination combines the received signals from the source and the relays using maximal ratio Combining (MRC). The transmission ends successfully once the accumulated signal-to-noise ratio (SNR) exceeds a predefined threshold. The number of relays participating in the transmission is adapted to the channel conditions based on the feedback from the destination. The use of incremental relaying allows obtaining a higher spectral efficiency. Moreover, the symbol error probability (SEP) performance is enhanced by using MRC at the relays. The use of MRC at the relays implies that each relay overhears the signals from the source and all previous relays and combines them using MRC. The proposed protocol differs from most of existing relaying protocol by the fact that it combines both incremental relaying and MRC at the relays for a multinode topology. Our analyses for a decode-and-forward mode show that: (i) compared to existing multinode relaying schemes, the proposed scheme can essentially achieve the same SEP performance but with less average number of time slots, (ii) compared to schemes without MRC at the relays, the proposed scheme can approximately achieve a 3 dB gain.

Spectral efficiency enhancement with interference cancellation for wireless relay network

DEFF Research Database (Denmark)

Yomo, Hiroyuki; De Carvalho, Elisabeth

The introduction of relaying into wireless communication system for coverage enhancement can cause severe decrease of spectral efficiency due to the requirement on extra radio resource. In this paper, we propose a method to increase spectral efficiency in such a wireless relay network by employing...... an interference cancellation technique. We focus on a typical scenario of relaying in a cellular system, where a mobile station (MS) requires the help of a relay station (RS) to communicate with the base station (BS). In such a case, interference cancellation can be used to achieve a small reuse distance...... of identical radio resource. We analyze a simple scenario with BS, single RS, and 2 MSs, and show that the proposed method has significant potential to enhance spectral efficiency in wireless relay networks....

Resource allocation for relay assisted cognitive radio networks

KAUST Repository

Zafar, Ammar; Alouini, Mohamed-Slim; Chen, Yunfei; Radaydeh, Redha M.

2012-01-01

transmission power and the relay transmission power. Numerical results show that the optimal sensing time is dependent on the primary user's signal-to-noise-ratio (SNR). They also show that SCR increases with increase in the number of relays. © 2012 IEEE.

Protective relaying of power systems using mathematical morphology

CERN Document Server

Wu, QH; Ji, TY

2009-01-01

Discusses the development of novel protective relaying algorithms, using Mathematical Morphology (MM). This book introduces the fundamental principles of MM, and brings together the applications of MM to develop different protective relaying algorithms for the protection of a variety of power system components.

Transverse Feedback for Electron-Cooled DC-Beam at COSY

International Nuclear Information System (INIS)

Kamerdzhiev, V.; Dietrich, J.

2004-01-01

At the cooler synchrotron COSY, high beam quality is achieved by means of beam cooling. In the case of intense electron-cooled beams, fast particle losses due to transverse coherent beam oscillations are regularly observed. To damp the instabilities a transverse feedback system was installed and successfully commissioned. Commissioning of the feedback system resulted in a significant increase of the e-cooled beam intensity by single injection and when cooling and stacking of repeated injections is applied. External experiments profit from the small diameter beams and the reduced halo. A transverse damping system utilizing a pick-up, signal processing electronics, power amplifiers, and a stripline deflector is introduced. Beam current and Schottky spectra measurements with the vertical feedback system turned on and off are presented

COMPACT HYPERSPECTRAL IMAGING SYSTEM (COSI FOR SMALL REMOTELY PILOTED AIRCRAFT SYSTEMS (RPAS – SYSTEM OVERVIEW AND FIRST PERFORMANCE EVALUATION RESULTS

Directory of Open Access Journals (Sweden)

A. A. Sima

2016-06-01

Full Text Available This paper gives an overview of the new COmpact hyperSpectral Imaging (COSI system recently developed at the Flemish Institute for Technological Research (VITO, Belgium and suitable for remotely piloted aircraft systems. A hyperspectral dataset captured from a multirotor platform over a strawberry field is presented and explored in order to assess spectral bands co-registration quality. Thanks to application of line based interference filters deposited directly on the detector wafer the COSI camera is compact and lightweight (total mass of 500g, and captures 72 narrow (FWHM: 5nm to 10 nm bands in the spectral range of 600-900 nm. Covering the region of red edge (680 nm to 730 nm allows for deriving plant chlorophyll content, biomass and hydric status indicators, making the camera suitable for agriculture purposes. Additionally to the orthorectified hypercube digital terrain model can be derived enabling various analyses requiring object height, e.g. plant height in vegetation growth monitoring. Geometric data quality assessment proves that the COSI camera and the dedicated data processing chain are capable to deliver very high resolution data (centimetre level where spectral information can be correctly derived. Obtained results are comparable or better than results reported in similar studies for an alternative system based on the Fabry–Pérot interferometer.

Novel Material Integration for Reliable and Energy-Efficient NEM Relay Technology

Science.gov (United States)

Chen, I.-Ru

Energy-efficient switching devices have become ever more important with the emergence of ubiquitous computing. NEM relays are promising to complement CMOS transistors as circuit building blocks for future ultra-low-power information processing, and as such have recently attracted significant attention from the semiconductor industry and researchers. Relay technology potentially can overcome the energy efficiency limit for conventional CMOS technology due to several key characteristics, including zero OFF-state leakage, abrupt switching behavior, and potentially very low active energy consumption. However, two key issues must be addressed for relay technology to reach its full potential: surface oxide formation at the contacting surfaces leading to increased ON-state resistance after switching, and high switching voltages due to strain gradient present within the relay structure. This dissertation advances NEM relay technology by investigating solutions to both of these pressing issues. Ruthenium, whose native oxide is conductive, is proposed as the contacting material to improve relay ON-state resistance stability. Ruthenium-contact relays are fabricated after overcoming several process integration challenges, and show superior ON-state resistance stability in electrical measurements and extended device lifetime. The relay structural film is optimized via stress matching among all layers within the structure, to provide lower strain gradient (below 10E-3/microm -1) and hence lower switching voltage. These advancements in relay technology, along with the integration of a metallic interconnect layer, enable complex relay-based circuit demonstration. In addition to the experimental efforts, this dissertation theoretically analyzes the energy efficiency limit of a NEM switch, which is generally believed to be limited by the surface adhesion energy. New compact (electronic device technology.

A Stochastic Geometry Approach to Full-Duplex MIMO Relay Network

Directory of Open Access Journals (Sweden)

Mhd Nour Hindia

2018-01-01

Full Text Available Cellular networks are extensively modeled by placing the base stations on a grid, with relays and destinations being placed deterministically. These networks are idealized for not considering the interferences when evaluating the coverage/outage and capacity. Realistic models that can overcome such limitation are desirable. Specifically, in a cellular downlink environment, the full-duplex (FD relaying and destination are prone to interferences from unintended sources and relays. However, this paper considered two-hop cellular network in which the mobile nodes aid the sources by relaying the signal to the dead zone. Further, we model the locations of the sources, relays, and destination nodes as a point process on the plane and analyze the performance of two different hops in the downlink. Then, we obtain the success probability and the ergodic capacity of the two-hop MIMO relay scheme, accounting for the interference from all other adjacent cells. We deploy stochastic geometry and point process theory to rigorously analyze the two-hop scheme with/without interference cancellation. These attained expressions are amenable to numerical evaluation and are corroborated by simulation results.

Minimax robust relay selection based on uncertain long-term CSI

KAUST Repository

Nisar, Muhammad Danish

2014-02-01

Cooperative communications via multiple relay nodes is known to provide the benefits of increase diversity and coverage. Simultaneous transmission via multiple relays, however, requires strong coordination between nodes either in terms of slot-based transmission or distributed space-time (ST) code implementation. Dynamically selecting a single best relay out of multiple relays and then using it alone for cooperative transmission alleviates the need for this strong coordination while still reaping the benefits of increased diversity and coverage. In this paper, we consider the design of relay selection (RS) under an imperfect knowledge of long-term channel state information (CSI) at the relay nodes, and we pursue minimax optimization to arrive at a robust RS approach that promises the best guarantee on the worst-case end-to-end signal-to-noise ratio (SNR). We provide some intuitive examples and extensive simulation results, not only in terms of worst-case SNR performance but also in terms of average bit-error-rate (BER) performance, to demonstrate the benefits of the proposed minimax robust RS scheme. © 2013 IEEE.

Conformational exchange of aromatic side chains characterized by L-optimized TROSY-selected ¹³C CPMG relaxation dispersion.

Science.gov (United States)

Weininger, Ulrich; Respondek, Michal; Akke, Mikael

2012-09-01

Protein dynamics on the millisecond time scale commonly reflect conformational transitions between distinct functional states. NMR relaxation dispersion experiments have provided important insights into biologically relevant dynamics with site-specific resolution, primarily targeting the protein backbone and methyl-bearing side chains. Aromatic side chains represent attractive probes of protein dynamics because they are over-represented in protein binding interfaces, play critical roles in enzyme catalysis, and form an important part of the core. Here we introduce a method to characterize millisecond conformational exchange of aromatic side chains in selectively (13)C labeled proteins by means of longitudinal- and transverse-relaxation optimized CPMG relaxation dispersion. By monitoring (13)C relaxation in a spin-state selective manner, significant sensitivity enhancement can be achieved in terms of both signal intensity and the relative exchange contribution to transverse relaxation. Further signal enhancement results from optimizing the longitudinal relaxation recovery of the covalently attached (1)H spins. We validated the L-TROSY-CPMG experiment by measuring fast folding-unfolding kinetics of the small protein CspB under native conditions. The determined unfolding rate matches perfectly with previous results from stopped-flow kinetics. The CPMG-derived chemical shift differences between the folded and unfolded states are in excellent agreement with those obtained by urea-dependent chemical shift analysis. The present method enables characterization of conformational exchange involving aromatic side chains and should serve as a valuable complement to methods developed for other types of protein side chains.

Quasi-period oscillations of relay feedback systems

International Nuclear Information System (INIS)

Wen Guilin; Wang Qingguo; Lee, T.H.

2007-01-01

This paper presents an analytical method for investigation of the existence and stability of quasi-period oscillations (torus solutions) for a class of relay feedback systems. The idea is to analyze Poincare map from one switching surface to the next based on the Hopf bifurcation theory of maps. It is shown that there exist quasi-period oscillations in certain relay feedback systems

Interference alignment for degrees of freedom improvement in 3-relay half-duplex systems

KAUST Repository

Park, Seongho

2011-12-01

In a half-duplex relaying, the capacity pre-log factor is a major drawback in spectral efficiency. This paper proposes a linear precoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help the communication between the source and the destination. In our proposed scheme, we consider a phase incoherent method in relays in which the source alternately transmits message signals to the different relays. In addition, we propose a linear interference alignment scheme which can eliminate the inter-relay interference resulted from the phase incoherence of relaying. Based on our analysis of degrees of freedom and our simulation results, we show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying. © 2011 IEEE.

Overlay cognitive radio systems with adaptive two-way relaying

KAUST Repository

Hyadi, Amal

2013-12-01

In this paper, we propose a spectrum sharing mechanism with a two-phase two-way relaying protocol for an overlay cognitive network. The system comprises two primary users (PUs) and two secondary users (SUs). One of the SUs acts as a relay for the PUs and gains spectrum sharing as long as he respects outage probability constraints of the primary system. Moreover, we consider that the relaying node performs an optimal power allocation scheme that minimizes the outage performance of the secondary receiver. Closed form expressions for the outage probability are derived for the cases of Decode-and-Forward (DF), Amplify-and-Forward (AF), and adaptive relaying. Numerical simulations are presented to illustrate and compare the obtained results. © 2013 IEEE.

Best relay selection using SNR and interference quotient for underlay cognitive networks

KAUST Repository

Hussain, Syed Imtiaz

2012-06-01

Cognitive networks in underlay settings operate simultaneously with the primary networks satisfying stringent interference limits. This condition forces them to operate with low transmission powers and confines their area of coverage. In an effort to reach remote destinations, underlay cognitive sources make use of relaying techniques. Selecting the best relay among those who are ready to cooperate is different in underlay settings than traditional non-cognitive networks. In this paper, we present a relay selection scheme which uses the quotient of the relay link signal to noise ratio (SNR) and the interference generated from the relay to the primary user to choose the best relay. The proposed scheme optimizes this quotient in a way to maximize the relay link SNR above a certain value whereas the interference is kept below a defined threshold. We derive closed expressions for the outage probability and bit error probability of the system incorporating this scheme. Simulation results confirm the validity of the analytical results and reveal that the relay selection in cognitive environment is feasible in low SNR regions. © 2012 IEEE.

Adaptive transmission based on multi-relay selection and rate-compatible LDPC codes

Science.gov (United States)

Su, Hualing; He, Yucheng; Zhou, Lin

2017-08-01

In order to adapt to the dynamical changeable channel condition and improve the transmissive reliability of the system, a cooperation system of rate-compatible low density parity check (RC-LDPC) codes combining with multi-relay selection protocol is proposed. In traditional relay selection protocol, only the channel state information (CSI) of source-relay and the CSI of relay-destination has been considered. The multi-relay selection protocol proposed by this paper takes the CSI between relays into extra account in order to obtain more chances of collabration. Additionally, the idea of hybrid automatic request retransmission (HARQ) and rate-compatible are introduced. Simulation results show that the transmissive reliability of the system can be significantly improved by the proposed protocol.

Frame Allocation and Scheduling for Relay Networks in the LTE Advanced Standard

OpenAIRE

Roth, Stefan

2010-01-01

The use of relays is seen as a promising way to extend cell coverage and increase rates in LTE Advanced networks. Instead of increasing the number of base stations (BS), relays with lower cost could provide similar gains. A relay will have a wireless link to the closest BS as only connection to the core network and will cover areas close to the cell edge or other areas with limited rates. Performing transmissions in several hops (BS-relay & relay-user) requires more radio resources than u...

77 FR 16435 - Transmission Relay Loadability Reliability Standard

Science.gov (United States)

2012-03-21

... conditions on all applicable transmission lines and transformers. I. Background A. Relay Protection Systems 2... and a power swing. If a power swing is detected, the protection system, ``blocks,'' or prevents the... to the reliability of the Bulk-Power System by requiring load-responsive phase protection relay...

76 FR 58424 - Transmission Relay Loadability Reliability Standard

Science.gov (United States)

2011-09-21

... distribution providers to set load-responsive phase protection relays according to specific criteria to ensure...-part R.1.10 allows transmission owners, generation owners and distribution providers to set transformer.... Thus, requiring that transformer fault protection relays are set to not expose the transformer to a...

Development of a Relay Performance Web Tool for the Mars Network

Science.gov (United States)

Allard, Daniel A.; Edwards, Charles D.

2009-01-01

Modern Mars surface missions rely upon orbiting spacecraft to relay communications to and from Earth systems. An important component of this multi-mission relay process is the collection of relay performance statistics supporting strategic trend analysis and tactical anomaly identification and tracking.

Micro-relay technology for energy-efficient integrated circuits

CERN Document Server

Kam, Hei

2015-01-01

This book describes the design of relay-based circuit systems from device fabrication to circuit micro-architectures. This book is ideal for both device engineers as well as circuit system designers and highlights the importance of co-design across design hierarchies when optimizing system performance (in this case, energy-efficiency). This book is ideal for researchers and engineers focused on semiconductors, integrated circuits, and energy efficient electronics. This book also: ·         Covers microsystem fabrication, MEMS device design, circuit design, circuit micro-architecture, and CAD ·         Describes work previously done in the field and also lays the groundwork and criteria for future energy-efficient device and system design ·         Maximizes reader insights into the design and modeling of micro-relay, micro-relay reliability, integrated circuit design with micro-relays, and more

Linear Processing Design of Amplify-and-Forward Relays for Maximizing the System Throughput

Directory of Open Access Journals (Sweden)

Qiang Wang

2018-01-01

Full Text Available In this paper, firstly, we study the linear processing of amplify-and-forward (AF relays for the multiple relays multiple users scenario. We regard all relays as one special “relay”, and then the subcarrier pairing, relay selection and channel assignment can be seen as a linear processing of the special “relay”. Under fixed power allocation, the linear processing of AF relays can be regarded as a permutation matrix. Employing the partitioned matrix, we propose an optimal linear processing design for AF relays to find the optimal permutation matrix based on the sorting of the received SNR over the subcarriers from BS to relays and from relays to users, respectively. Then, we prove the optimality of the proposed linear processing scheme. Through the proposed linear processing scheme, we can obtain the optimal subcarrier paring, relay selection and channel assignment under given power allocation in polynomial time. Finally, we propose an iterative algorithm based on the proposed linear processing scheme and Lagrange dual domain method to jointly optimize the joint optimization problem involving the subcarrier paring, relay selection, channel assignment and power allocation. Simulation results illustrate that the proposed algorithm can achieve a perfect performance.

A study on Relay Effect via Magnetic Resonant Coupling for Wireless Power Transfer

Directory of Open Access Journals (Sweden)

Rashid N.A.

2016-01-01

Full Text Available Wireless power transfer (WPT transmits electrical energy from a power source to an electrical load wirelessly or without any conductors. The capability of WPT to transmit the energy is limited. Therefore, a relay was introduced to increase the distance of the WPT capabilities. The effect of the relay has been investigated to extend the energy transfer distance. The effect of relay was demonstrated by placing a relay coil between transmitter and receiver, relay biased to transmitter and placing two relay coils in the designed system. Experimental results are provided to prove the concept of the relay effect. The power transmission efficiency can be achieved up to 75% at 1 meter distance.

The impact of SFCL and SMES integration on the distance relay

Energy Technology Data Exchange (ETDEWEB)

Yang, Jun, E-mail: JYang@whu.edu.cn [School of Electrical Engineering, Wuhan University, Wuhan 430072 (China); Zhang, Liling; Wang, Xinpu; Chen, Lei [School of Electrical Engineering, Wuhan University, Wuhan 430072 (China); Chen, Yanxia [Beijing Electric Power Research Institute, Beijing 100075 (China)

2016-11-15

Highlights: • The impact of SFCL and SMES integration on the circle distance relay is studied. • The detailed models of SFCL and SMES with distance delay are built in MATLAB. • The integration of SFCL and SMES does influence the operation of distance relay. • An improved distance relay to prevent mal-operation is proposed and verified. - Abstract: The superconducting fault current limiter (SFCL) is an ideal short-circuit fault current limiting device that can limit the fault current without any delay and control the voltage drop of the non-fault line. The superconducting magnetic energy storage (SMES) device can exchange the active and reactive power independently, so it is applied broadly to improve power system stability. With SFCL, the low voltage ride-through capability of SMES can be enhanced as well as its MW and MJ capacities. The distance relay is a key electrical apparatus that will trip circuit breakers to protect electrical devices from short circuit faults. Due to the application of SFCL and SMES integration, the voltage and current in power grid will change accordingly, and the operation characteristic of distance relay may be affected. In this paper, the impact of a bridge-type SFCL and SMES integration on the circle distance relay is studied. And simulation results show that the integration of SFCL and SMES does influence the measured impedance of distance relay, which can lead to mal-operation of the circle distance relay. Furthermore, an improved distance relay is proposed and verified.

The impact of SFCL and SMES integration on the distance relay

International Nuclear Information System (INIS)

Yang, Jun; Zhang, Liling; Wang, Xinpu; Chen, Lei; Chen, Yanxia

2016-01-01

Highlights: • The impact of SFCL and SMES integration on the circle distance relay is studied. • The detailed models of SFCL and SMES with distance delay are built in MATLAB. • The integration of SFCL and SMES does influence the operation of distance relay. • An improved distance relay to prevent mal-operation is proposed and verified. - Abstract: The superconducting fault current limiter (SFCL) is an ideal short-circuit fault current limiting device that can limit the fault current without any delay and control the voltage drop of the non-fault line. The superconducting magnetic energy storage (SMES) device can exchange the active and reactive power independently, so it is applied broadly to improve power system stability. With SFCL, the low voltage ride-through capability of SMES can be enhanced as well as its MW and MJ capacities. The distance relay is a key electrical apparatus that will trip circuit breakers to protect electrical devices from short circuit faults. Due to the application of SFCL and SMES integration, the voltage and current in power grid will change accordingly, and the operation characteristic of distance relay may be affected. In this paper, the impact of a bridge-type SFCL and SMES integration on the circle distance relay is studied. And simulation results show that the integration of SFCL and SMES does influence the measured impedance of distance relay, which can lead to mal-operation of the circle distance relay. Furthermore, an improved distance relay is proposed and verified.

Cooperation schemes for rate enhancement in detect-and-forward relay channels

KAUST Repository

Benjillali, Mustapha

2010-05-01

To improve the spectral efficiency of "Detect-and-Forward" (DetF) half-duplex relaying in fading channels, we propose a cooperation scheme where the relay uses a modulation whose order is higher than the one at the source. In a new common framework, we show that the proposed scheme offers considerable gains - in terms of achievable information rates - compared to the conventional DetF relaying schemes for both orthogonal and non-orthogonal source/relay cooperation. This allows us to propose an adaptive cooperation scheme based on the maximization of the information rate at the destination which needs to observe only the average signal-to-noise ratios of direct and relaying links. ©2010 IEEE.

IEEE C37.98-1987: IEEE standard seismic testing of relays

International Nuclear Information System (INIS)

Anon.

1992-01-01

This standard specifies the procedures to be used in the seismic testing of relays used in power system facilities. The standard is concerned with the determination of the seismic fragility level of relays and also gives recommendations for proof testing. The purpose of this standard is to establish procedures for determining the seismic capabilities of protective and auxiliary relays. These procedures employ what has been called fragility testing in IEEE Std 344-1987. To define the conditions for fragility testing of relays, parameters in three separate areas must be specified. In general, they are (1) the electrical settings and inputs to the relay, and other information to define its conditions during the test; (2) the change in state, deviation in operating characteristics or tolerances, or other change of performance of the relay that constitutes failure; (3) the seismic vibration environment to be imposed during the test. Since it is not possible to define the conditions for every conceivable application for all relays, those parameters, which in practice encompass the majority of applications, have been specified in this standard. When the application of the relay is other than as specified under any of (1), (2), and (3), or if it is not practical to apply existing results of fragility tests to that new application, then proof testing must be performed for that new case

IEEE C37.98-1978: IEEE standard seismic testing of relays

International Nuclear Information System (INIS)

Anon.

1992-01-01

This standard specifies the procedures to be used in the seismic testing of relays used in power system facilities. The standard is concerned with the determination of the seismic fragility level of relays and also gives recommendations for proof testing. The purpose of this standard is to establish procedures for determining the seismic capabilities of protective and auxiliary relays. These procedures employ what has been called fragility testing in ANSI/IEEE Std 344-1975, Recommended Practices for Seismic Qualification of Class 1E Equipment for Nuclear Power Generating Stations. In order to define the conditions for fragility testing of relays, parameters in three separate areas must be specified. In general they are: (1) the electrical settings and inputs to the relay, and other information to define its conditions during the test; (2) the change in state, deviation in operating characteristics or tolerances, or other change of performance of the relay which constitutes failure; (3) the seismic vibration environment to be imposed during the test. Since it is not possible to define the conditions for every conceivable application for all relays, those parameters, which in practice encompass the majority of applications, have been specified in this standard. When the application of the relay is other than as specified under any of (1), (2), and (3), or if it is not practical to apply existing results of fragility tests to that new case

Modeling and Simulation of Out of Step Blocking Relay for

Directory of Open Access Journals (Sweden)

Ahmed A. Al Adwani

2013-05-01

Full Text Available  This paper investigates a power swing effect on a distance protection relay performance installed on (HV/EHV transmission line as well as power system stability. A conventional distance relay can’t properly operate under transient stability conditions; therefore, it cause mol-operation, and it will adversely impact on its trip signals. To overcome this problem, the Out Of Step (OOS relay has modeled and simulated to joint with distance relay to supervise and control on its trip signals response. The setting characteristics technique of the OOS based on concentric polygons scheme method to detect power swing under transient stability situation.         This study ia a modeling and simulating using (Maltab\\ Simulink software. A Two relays had been  performed   and  tested  with  two equivalents network connected to ends.      The results of this study showed an activity and reliability of this way to control the distance relay response under a transient stability conditions and it indicated the possibility to find out faults which may occur at period of power swing

STUDI ANALISIS KOORDINASI OVER CURRENT RELAY (OCR) DAN GROUND FAULT RELAY (GFR) PADA RECLOSER DI SALURAN PENYULANG PENEBEL

OpenAIRE

I Dewa Gde Agung Budhi Udiana; I G Dyana Arjana; Tjok Gede Indra Partha

2017-01-01

Short circuit causing over current problem and can might causing interference of the equipment performance such as distribution transformers also causing widespread disruption occurred. In resolving such interference is required as protection system on the distribution system. Seeing all above is needed coordination between the supporting component of the protection system which is consisted of Over Current Relay (OCR) and Ground Fault Relay (GFR). The research was conducted at PT. PLN (Perse...

On the Outage Performance of Full-Duplex Selective Decode-and-Forward Relaying

KAUST Repository

Khafagy, Mohammad Galal

2013-02-25

We evaluate the outage performance in a three-terminal full-duplex relay channel that adopts a selective decode-and-forward protocol, taking relay self-interference into account. Previous work focused on coverage extension scenarios where direct source-destination transmissions are neglected or considered as interference. In this work, we account for the relay self-interference, and exploit the cooperative diversity offered by the independently fading source/relay message replicas that arrive at the destination. We present an approximate, yet accurate, closed-form expression for the end-to-end outage probability that captures their joint effect. With the derived expression in hand, we propose a relay transmit power optimization scheme that only requires the relay knowledge of channel statistics. Finally, we corroborate our analysis with simulations.

Whether and Where to Code in the Wireless Relay Channel

DEFF Research Database (Denmark)

Shi, Xiaomeng; Médard, Muriel; Roetter, Daniel Enrique Lucani

2013-01-01

The throughput benefits of random linear network codes have been studied extensively for wirelined and wireless erasure networks. It is often assumed that all nodes within a network perform coding operations. In energy-constrained systems, however, coding subgraphs should be chosen to control...... the number of coding nodes while maintaining throughput. In this paper, we explore the strategic use of network coding in the wireless packet erasure relay channel according to both throughput and energy metrics. In the relay channel, a single source communicates to a single sink through the aid of a half......-duplex relay. The fluid flow model is used to describe the case where both the source and the relay are coding, and Markov chain models are proposed to describe packet evolution if only the source or only the relay is coding. In addition to transmission energy, we take into account coding and reception...

An Optimal Analysis in Wireless Powered Full-duplex Relaying Network

Directory of Open Access Journals (Sweden)

K.-T. Nguyen

2017-04-01

Full Text Available Wireless-powered cellular networks (WPCNs are currently being investigated to exploit the reliability and improve battery lifetime of mobile users. This paper investigates the energy harvesting structure of the full-duplex relaying networks. By using the time switching based relaying (TSR protocol and Amplify-and-Forward (AF model in delay-limited transmission scheme, we propose the closed-form expression of the outage probability and then calculate the optimal throughput. An important result can be taken obviously that the time fraction in TSR, the position of relay, the noise as well as the energy conversation impacting on the outage probability as well as the optimal throughput. By Monte Carlo simulation, the numerical results indicate an effective relaying strategy in full-duplex cooperative systems. Finally, we provide fundamental design guidelines for selecting time fraction in TSR that satisfies the requirements of a practical relaying system.

Toward distributed relay selection for opportunistic amplify-and-forward transmission

KAUST Repository

Tourki, Kamel

2011-05-01

Opportunistic relaying in cooperative communication depends on careful relay selection. However the traditional centralized method used for opportunistic Amplify-and-Forward (OAF) protocols requires precise measurements of channel state information (CSI) at the destination (CSI-OAF). In this paper, we propose a distributed relay selection framework for opportunistic AF (D-OAF) cooperative communications and offer an accurate performance analysis based on exact statistics of the local signalto- noise ratios of the best relay. Furthermore, we validate our analysis by showing that performance simulation results coincide with our analytical results over different network architectures, and we compare our new results with their CSI-based counterparts. © 2011 IEEE.

FPGA-based upgrade of the read-out electronics for the low energy polarimeter at COSY/Juelich

Energy Technology Data Exchange (ETDEWEB)

Hempelmann, Nils [Institut fuer Kernphysik, Forschungszentrum Juelich (Germany); Collaboration: JEDI-Collaboration

2016-07-01

The Cooler Synchrotron (COSY) is a facility for cooled polarized beams at the Forschungszentrum in Juelich. The Low Energy Polarimeter (LEP) is the polarimeter in the injection beam line of COSY. The beam polarization is measured using scattering off carbon and polyethylene (CH2) targets. The outgoing particles are detected using twelve plastic scintillators installed in groups of three to the left, to the right, above, and below the beam. The LEP is the routine tool for beam set-up, but its performance was limited by the old read-out electronics consisting of analog NIM modules. A new system using analog pulse sampling and an FPGA chip for signal processing was installed and tested. The ejectile particles were identified by relative time of flight measurement using a signal from the RF amplifier of the cyclotron used for acceleration as a reference. The new system is able to measure the time at which a particle arrives to an accuracy in the order of 50 ps. The presentation includes a review of available systems and a report about measurements in May and December 2015.

Use of Behavior and Influence Functions for Relay Selection in Cooperative Communications

DEFF Research Database (Denmark)

Craciunescu, Razvan; Mihovska, Albena Dimitrova; Prasad, Ramjee

2015-01-01

This paper uses a novel set of functions to model the relay selection process in a scenario of cooperative wireless communications. We define a utility function that reflects the behavior and influence that a selected relay may have on the quality of the link to be established for the forwarding...... of data. The utility function takes into account also the strategies of other players. To this end, we define a relay selection game and a supporting Nash Equilibrium (NE) algorithm for the choice of a relay during communication. The successful selection of a relay is evaluated by simulations in terms...

CERN Relay Race

CERN Multimedia

2004-01-01

The CERN Relay Race will take place around the Meyrin site on Wednesday 19 May between 12.15 and 12.35. If possible, please avoid driving on the site during this 20 minute period. If you do meet runners in your car, please STOP until they all have passed. Thank you for your understanding

CERN Relay Race

CERN Multimedia

2001-01-01

The CERN Relay Race will take place around the Meyrin site on Wednesday 23 May between 12:20 and 12:35. If possible, please avoid driving on the site during this 15 minute period. If you do meet runners in your car, please stop until they all have passed. Thank you for your understanding.

Two-phase CFD PTS validation in an extended range of thermohydraulics conditions covered by the COSI experiment

International Nuclear Information System (INIS)

Coste, P.; Ortolan, A.

2014-01-01

Highlights: • Models for large interfaces in two-phase CFD were developed for PTS. • The COSI experiment is used for NEPTUNE C FD integral validation. • COSI is a PWR cold leg scaled 1/100 for volume. • Fifty runs are calculated, covering a large range of flow configurations. • The CFD predicting capability is analysed using global and local measurements. - Abstract: In the context of the Pressurized Water Reactors (PWR) life duration safety studies, some models were developed to address the Pressurized Thermal Shock (PTS) from the two-phase CFD angle, dealing with interfaces much larger than cells size and with direct contact condensation. Such models were implemented in NEPTUNE C FD, a 3D transient Eulerian two-fluid model. The COSI experiment is used for its integral validation. It represents a cold leg scaled 1/100 for volume and power from a 900 MW PWR under a large range of LOCA PTS conditions. In this study, the CFD is evaluated in the whole range of parameters and flow configurations covered by the experiment. In a first step, a single choice of mesh and CFD models parameters is fixed and justified. In a second step, fifty runs are calculated. The CFD predicting capability is analysed, comparing the liquid temperature and the total condensation rate with the experiment, discussing their dependency on the inlet cold liquid rate, on the liquid level in the cold leg and on the difference between co-current and counter-current runs. It is shown that NEPTUNE C FD 1.0.8 calculates with a fair agreement a large range of flow configurations related to ECCS injection and steam condensation

Two-way CSI-assisted AF relaying with HPA nonlinearity

KAUST Repository

Qi, Jian; Aissa, Sonia; Alouiniz, Mohamed-Slim

2015-01-01

In this paper, we investigate half-duplex two-way dual-hop channel state information (CSI)-assisted amplify-andforward (AF) relaying in the presence of high-power amplifier (HPA) nonlinearity at relays. The expression for the end-toend signal

CERN Relay Race

CERN Multimedia

Running Club

2010-01-01

This year’s CERN Relay Race will take place around the Meyrin site on Thursday 20th May at 12h00. This annual event is for teams of 6 runners covering distances of 1000m, 800m, 800m, 500m, 500m and 300m respectively. Teams may be entered in the Seniors, Veterans, Ladies, Mixed or Open categories. The registration fee is 10 CHF per runner, and each runner receives a souvenir prize. As usual, there will be a programme of entertainments from 12h in the arrival area, in front of the Restaurant no. 1. Drinks, food, CERN club information and music will be available for the pleasure of both runners and spectators. The race starts at 12h15, with results and prize giving at 13:15.   For details of the race, and of how to sign up a team, please visit: https://espace.cern.ch/Running-Club/CERN-Relay The event is organised by the CERN Running Club with the support of the CERN Staff Association.  

Energy-efficient cooperative protocols for full-duplex relay channels

KAUST Repository

Khafagy, Mohammad Galal

2013-12-01

In this work, energy-efficient cooperative protocols are studied for full-duplex relaying (FDR) with loopback interference. In these protocols, relay assistance is only sought under certain conditions on the different link outages to ensure effective cooperation. Recently, an energy-efficient selective decode-And-forward protocol was proposed for FDR, and was shown to outperform existing schemes in terms of outage. Here, we propose an incremental selective decode-And-forward protocol that offers additional power savings, while keeping the same outage performance. We compare the performance of the two protocols in terms of the end-to-end signal-to-noise ratio cumulative distribution function via closed-form expressions. Finally, we corroborate our theoretical results with simulation, and show the relative relay power savings in comparison to non-selective cooperation in which the relay cooperates regardless of channel conditions. © 2013 IEEE.

New results on performance analysis of opportunistic regenerative relaying

KAUST Repository

Tourki, Kamel

2013-12-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path may be unusable, and takes into account the effect of the possible erroneously detected and transmitted data at the selected relay. We first derive the signal-to-noise (SNR) statistics for each hop, which are used to determine accurate closed form expressions for end-to-end bit-error rate (BER) of binary phase-shift keying (BPSK) modulation and end-to-end outage probability for a transmission rate R over Rayleigh fading channels. Furthermore, we evaluate the asymptotical performance and deduce the diversity order. Finally, we validate our analysis by showing that performance simulation results coincide with our analytical results over linear network architecture. © 2013 Elsevier B.V.

Energy-efficient cooperative protocols for full-duplex relay channels

KAUST Repository

Khafagy, Mohammad Galal; Ismail, Amr; Alouini, Mohamed-Slim; Aï ssa, Sonia

2013-01-01

In this work, energy-efficient cooperative protocols are studied for full-duplex relaying (FDR) with loopback interference. In these protocols, relay assistance is only sought under certain conditions on the different link outages to ensure effective cooperation. Recently, an energy-efficient selective decode-And-forward protocol was proposed for FDR, and was shown to outperform existing schemes in terms of outage. Here, we propose an incremental selective decode-And-forward protocol that offers additional power savings, while keeping the same outage performance. We compare the performance of the two protocols in terms of the end-to-end signal-to-noise ratio cumulative distribution function via closed-form expressions. Finally, we corroborate our theoretical results with simulation, and show the relative relay power savings in comparison to non-selective cooperation in which the relay cooperates regardless of channel conditions. © 2013 IEEE.

Information-guided transmission in decode-and-forward relaying systems: Spatial exploitation and throughput enhancement

KAUST Repository

Yang, Yuli

2011-07-01

In addressing the issue of achieving high throughput in half-duplex relay channels, we exploit a concept of information-guided transmission for the network consisting of a source node, a destination node, and multiple half-duplex relay nodes. For further benefiting from multiple relay nodes, the relay-selection patterns are defined as the arbitrary combinations of given relay nodes. By exploiting the difference among the spatial channels states, in each relay-help transmission additional information to be forwarded is mapped onto the index of the active relay-selection pattern besides the basic information mapped onto the traditional constellation, which is forwarded by the relay node(s) in the active relay-selection pattern, so as to enhance the relay throughtput. With iterative decoding, the destination node can achieve a robust detection by decoupling the signals forwarded in different ways. We investigate the proposed scheme considering "decode-and-forward" protocol and establish its achievable transmission rate. The analytical results on capacity behaviors prove the efficiency of the proposed scheme by showing that it achieves better capacity performance than the conventional scheme. © 2011 IEEE.

Spatially Controlled Relay Beamforming

Science.gov (United States)

Kalogerias, Dionysios

This thesis is about fusion of optimal stochastic motion control and physical layer communications. Distributed, networked communication systems, such as relay beamforming networks (e.g., Amplify & Forward (AF)), are typically designed without explicitly considering how the positions of the respective nodes might affect the quality of the communication. Optimum placement of network nodes, which could potentially improve the quality of the communication, is not typically considered. However, in most practical settings in physical layer communications, such as relay beamforming, the Channel State Information (CSI) observed by each node, per channel use, although it might be (modeled as) random, it is both spatially and temporally correlated. It is, therefore, reasonable to ask if and how the performance of the system could be improved by (predictively) controlling the positions of the network nodes (e.g., the relays), based on causal side (CSI) information, and exploitting the spatiotemporal dependencies of the wireless medium. In this work, we address this problem in the context of AF relay beamforming networks. This novel, cyber-physical system approach to relay beamforming is termed as "Spatially Controlled Relay Beamforming". First, we discuss wireless channel modeling, however, in a rigorous, Bayesian framework. Experimentally accurate and, at the same time, technically precise channel modeling is absolutely essential for designing and analyzing spatially controlled communication systems. In this work, we are interested in two distinct spatiotemporal statistical models, for describing the behavior of the log-scale magnitude of the wireless channel: 1. Stationary Gaussian Fields: In this case, the channel is assumed to evolve as a stationary, Gaussian stochastic field in continuous space and discrete time (say, for instance, time slots). Under such assumptions, spatial and temporal statistical interactions are determined by a set of time and space invariant

Using the 5 P Relay in Task Groups

Science.gov (United States)

Stanley, Paula Helen

2006-01-01

This article describes the 5 P Relay, a group exercise that can increase the effectiveness of task groups. The 5 P Relay is based on the principles and concepts of the Invitational Model, which emphasizes the importance of assessing the effectiveness or health of five aspects of an organization's environment: people, places, programs, processes,…

77 FR 1039 - Internet-Based Telecommunications Relay Service Numbering

Science.gov (United States)

2012-01-09

... FEDERAL COMMUNICATIONS COMMISSION 47 CFR Part 64 [WC Docket No. 10-191; Report No. 2939] Internet... toll-free numbers by users of Internet- based Telecommunications Relay Services (iTRS). DATES... any rules of particular applicability. Subject: Internet-Based Telecommunications Relay Service...

CERN Relay Race

CERN Multimedia

2003-01-01

The CERN Relay Race will take place around the Meyrin site on Wednesday May 21st between 12h15 and 12h35. If possible, please avoid driving on the site during this 20 minute period. If you do meet runners in your car, please STOP until they all have passed. Thank you for your understanding

CERN Relay Race

CERN Document Server

2002-01-01

The CERN Relay Race will take place around the Meyrin site on Wednesday 22 May between 12h20 and 12h35. If possible, please avoid driving on the site during this 15 minute period. If you do meet runners in your car, please STOP until they all have passed. Thank you for your understanding.

Secrecy Capacity of a Class of Orthogonal Relay Eavesdropper Channels

Directory of Open Access Journals (Sweden)

Aggarwal Vaneet

2009-01-01

Full Text Available The secrecy capacity of relay channels with orthogonal components is studied in the presence of an additional passive eavesdropper node. The relay and destination receive signals from the source on two orthogonal channels such that the destination also receives transmissions from the relay on its channel. The eavesdropper can overhear either one or both of the orthogonal channels. Inner and outer bounds on the secrecy capacity are developed for both the discrete memoryless and the Gaussian channel models. For the discrete memoryless case, the secrecy capacity is shown to be achieved by a partial decode-and-forward (PDF scheme when the eavesdropper can overhear only one of the two orthogonal channels. Two new outer bounds are presented for the Gaussian model using recent capacity results for a Gaussian multiantenna point-to-point channel with a multiantenna eavesdropper. The outer bounds are shown to be tight for two subclasses of channels. The first subclass is one in which the source and relay are clustered, and the eavesdropper receives signals only on the channel from the source and the relay to the destination, for which the PDF strategy is optimal. The second is a subclass in which the source does not transmit to the relay, for which a noise-forwarding strategy is optimal.

Secure Communication for Two-Way Relay Networks with Imperfect CSI

Directory of Open Access Journals (Sweden)

Cong Sun

2017-09-01

Full Text Available This paper considers a two-way relay network, where two legitimate users exchange messages through several cooperative relays in the presence of an eavesdropper, and the Channel State Information (CSI of the eavesdropper is imperfectly known. The Amplify-and-Forward (AF relay protocol is used. We design the relay beamforming weights to minimize the total relay transmit power, while requiring the Signal-to-Noise-Ratio (SNRs of the legitimate users to be higher than the given thresholds and the achievable rate of the eavesdropper to be upper-bounded. Due to the imperfect CSI, a robust optimization problem is summarized. A novel iterative algorithm is proposed, where the line search technique is applied, and the feasibility is preserved during iterations. In each iteration, two Quadratically-Constrained Quadratic Programming (QCQP subproblems and a one-dimensional subproblem are optimally solved. The optimality property of the robust optimization problem is analyzed. Simulation results show that the proposed algorithm performs very close to the non-robust model with perfect CSI, in terms of the obtained relay transmit power; it~achieves higher secrecy rate compared to the existing work. Numerically, the proposed algorithm converges very quickly, and more than 85% of the problems are solved optimally.

Design of Asymmetrical Relay Resonators for Maximum Efficiency of Wireless Power Transfer

Directory of Open Access Journals (Sweden)

Bo-Hee Choi

2016-01-01

Full Text Available This paper presents a new design method of asymmetrical relay resonators for maximum wireless power transfer. A new design method for relay resonators is demanded because maximum power transfer efficiency (PTE is not obtained at the resonant frequency of unit resonator. The maximum PTE for relay resonators is obtained at the different resonances of unit resonator. The optimum design of asymmetrical relay is conducted by both the optimum placement and the optimum capacitance of resonators. The optimum placement is found by scanning the positions of the relays and optimum capacitance can be found by using genetic algorithm (GA. The PTEs are enhanced when capacitance is optimally designed by GA according to the position of relays, respectively, and then maximum efficiency is obtained at the optimum placement of relays. The capacitance of the second resonator to nth resonator and the load resistance should be determined for maximum efficiency while the capacitance of the first resonator and the source resistance are obtained for the impedance matching. The simulated and measured results are in good agreement.

Relay Placement for FSO Multihop DF Systems With Link Obstacles and Infeasible Regions

KAUST Repository

Zhu, Bingcheng

2015-05-19

Optimal relay placement is studied for free-space optical multihop communication with link obstacles and infeasible regions. An optimal relay placement scheme is proposed to achieve the lowest outage probability, enable the links to bypass obstacles of various geometric shapes, and place the relay nodes in specified available regions. When the number of relay nodes is large, the searching space can grow exponentially, and thus, a grouping optimization technique is proposed to reduce the searching time. We numerically demonstrate that the grouping optimization can provide suboptimal solutions close to the optimal solutions, but the average searching time linearly grows with the number of relay nodes. Two useful theorems are presented to reveal insights into the optimal relay locations. Simulation results show that our proposed optimization framework can effectively provide desirable solution to the problem of optimal relay nodes placement. © 2015 IEEE.

Semiconductor relay and its manufacture method. Handotai relay oyobi sono seizo hoho

Energy Technology Data Exchange (ETDEWEB)

Nakamura, M

1993-06-01

The invention relates to a semiconductor relay in which a light emitting diode and a photovoltaic element are arranged in the opposite positions and connected with a light connection and aims to present a light transmission path to transmit input signals to the light emitting diode to the side of the photovoltaic element with a negligible light loss effectively. The invention presents a semiconductor relay, in which a light emitting diode loaded on the first lead frame and the light receiving part of the photovoltaic element to drive a MOSFET element loaded on the second lead frame and acting as a switch element are connected through an insulator tube with an opaque outer wall, and the interior of the insulator tube is filled with a transparent insulating filler, so that the invention affords a light transmission path without light leakage from the interior of the opaque insulator tube and with the stability in the form and no light loss. 3 figs.

Novel half-coherent receivers for amplify-and-forward relaying

KAUST Repository

Khan, Fahd Ahmed; Chen, Yunfei; Alouini, Mohamed-Slim

2012-01-01

Consider a system in which the signal is transmitted from the source to the destination via an amplify-and-forward relay. For such a system, we derive in this paper, novel receivers that have complete knowledge of either the source-relay link

Relay-aided multi-cell broadcasting with random network coding

DEFF Research Database (Denmark)

Lu, Lu; Sun, Fan; Xiao, Ming

2010-01-01

We investigate a relay-aided multi-cell broadcasting system using random network codes, where the focus is on devising efficient scheduling algorithms between relay and base stations. Two scheduling algorithms are proposed based on different feedback strategies; namely, a one-step scheduling...

Mutual Information of Buffer-Aided Full-Duplex Relay Channels

KAUST Repository

Shafie, Ahmed El

2017-04-09

We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multiple-output (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

Mutual Information of Buffer-Aided Full-Duplex Relay Channels

KAUST Repository

Shafie, Ahmed El; Salem, Ahmed Sultan; Krikidis, Ioannis; Al-Dhahir, Naofal; Hamila, Ridha

2017-01-01

We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multiple-output (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

Performance analysis of selective cooperation with fixed gain relays in Nakagami-m channels

KAUST Repository

Hussain, Syed Imtiaz; Hasna, Mazen Omar; Alouini, Mohamed-Slim

2012-01-01

Selecting the best relay using the maximum signal to noise ratio (SNR) among all the relays ready to cooperate saves system resources and utilizes the available bandwidth more efficiently compared to the regular all-relay cooperation. In this paper, we analyze the performance of the best relay selection scheme with fixed gain relays operating in Nakagami-. m channels. We first derive the probability density function (PDF) of upper bounded end-to-end SNR of the relay link. Using this PDF, we derive some key performance parameters for the system including average bit error probability and average channel capacity. The analytical results are verified through Monte Carlo simulations. © 2012 Elsevier B.V.

Performance analysis of selective cooperation with fixed gain relays in Nakagami-m channels

KAUST Repository

Hussain, Syed Imtiaz

2012-09-01

Selecting the best relay using the maximum signal to noise ratio (SNR) among all the relays ready to cooperate saves system resources and utilizes the available bandwidth more efficiently compared to the regular all-relay cooperation. In this paper, we analyze the performance of the best relay selection scheme with fixed gain relays operating in Nakagami-. m channels. We first derive the probability density function (PDF) of upper bounded end-to-end SNR of the relay link. Using this PDF, we derive some key performance parameters for the system including average bit error probability and average channel capacity. The analytical results are verified through Monte Carlo simulations. © 2012 Elsevier B.V.

New resource allocation scheme for cognitive relay networks with opportunistic access

KAUST Repository

Zafar, Ammar

2012-06-01

In this paper, a new resource allocation scheme to minimize Symbol Error rate (SER) for relay assisted cognitive radio networks is studied. A cognitive relay network with amplify-and-forward (AF) fixed gain relays and opportunistic access to the licensed spectrum is considered. The SER objective function and the optimization constraints are derived first. The resource allocation algorithm is then derived using the Langrangian multiplier method. Closed form expressions are derived for the source and relay powers and, symbol time. Analytical results show that the optimal power allocation follows an extended water-filling solution. © 2012 IEEE.

Particle beam digital phase control system for COSY

International Nuclear Information System (INIS)

Schnase, A.

1994-02-01

Particle accelerators require that the orbit of the charged particles in the vacuum chamber is controlled to fulfil narrow limits. This is done by magnetic deflection systems and exactly adjusted rf-acceleration. Up to now the necessary control-functions were realised with analogue parts. This work describes a digital phase control system that works in real time and is used with the proton accelerator COSY. The physical design of the accelerator sets the accuracy-specifications of the revolution frequency (<1 Hz in the whole range from 400 kHz to 1.6 MHz), the phase-difference (<0.01 ), the signal-to-noise-ratio (<-60 dBc) and the update rate (<1 μs) of the parameters. In a typical operation the beam is first bunched and synchronised to the reference oscillator. After that the beam influences the rf-system with the help of charge detectors and now the rf-systems will be synchronised with the bunched beam. This control-loop is modelled and simulated with PSPICE. (orig.)

The sequence relay selection strategy based on stochastic dynamic programming

Science.gov (United States)

Zhu, Rui; Chen, Xihao; Huang, Yangchao

2017-07-01

Relay-assisted (RA) network with relay node selection is a kind of effective method to improve the channel capacity and convergence performance. However, most of the existing researches about the relay selection did not consider the statically channel state information and the selection cost. This shortage limited the performance and application of RA network in practical scenarios. In order to overcome this drawback, a sequence relay selection strategy (SRSS) was proposed. And the performance upper bound of SRSS was also analyzed in this paper. Furthermore, in order to make SRSS more practical, a novel threshold determination algorithm based on the stochastic dynamic program (SDP) was given to work with SRSS. Numerical results are also presented to exhibit the performance of SRSS with SDP.

Channel allocation and rate adaptation for relayed transmission over correlated fading channels

KAUST Repository

Hwang, Kyusung; Hossain, Md Jahangir; Ko, Youngchai; Alouini, Mohamed-Slim

2009-01-01

at both the source and relay nodes, we develop an optimal channel allocation and rate adaptation policy for a dual-hop relayed transmission. As such the overall transmit power for the relayed system is minimized while a target packet dropping rate (PDR

Gigantic magnetoelectric effect caused by magnetic-field-induced canted antiferromagnetic-paramagnetic transition in quasi-two-dimensional Ca2CoSi2O7 crystal

Science.gov (United States)

Akaki, M.; Tozawa, J.; Akahoshi, D.; Kuwahara, H.

2009-05-01

We have investigated the magnetic and dielectric properties of Ca2CoSi2O7 crystal. The dielectricity and magnetism of Ca2CoSi2O7 are strongly coupled below a canted antiferromagnetic transition temperature (TN). Magnetic fields induce electric polarization below TN. Interestingly, the magnetic-field-induced electric polarization is detected even without poling electric fields. Below TN, a canted antiferromagnetic-paramagnetic transition is induced by magnetic fields. The large magnetocapacitance is observed around TN. The origin of the large magnetocapacitance is due to the magnetic-field-induced the canted antiferromagnetic-paramagnetic transition.

Commercial grade item (CGI) dedication of MDR relays for nuclear safety related applications

Science.gov (United States)

Das, Ranjit K.; Julka, Anil; Modi, Govind

1994-08-01

MDR relays manufactured by Potter & Brumfield (P&B) have been used in various safety related applications in commercial nuclear power plants. These include emergency safety features (ESF) actuation systems, emergency core cooling systems (ECCS) actuation, and reactor protection systems. The MDR relays manufactured prior to May 1990 showed signs of generic failure due to corrosion and outgassing of coil varnish. P&B has made design changes to correct these problems in relays manufactured after May 1990. However, P&B does not manufacture the relays under any 10CFR50 Appendix B quality assurance (QA) program. They manufacture the relays under their commercial QA program and supply these as commercial grade items. This necessitates CGI Dedication of these relays for use in nuclear-safety-related applications. This paper presents a CGI dedication program that has been used to dedicate the MDR relays manufactured after been used to dedicate the MDR relays manufactured after May 1990. The program is in compliance with current Nuclear Regulatory Commission (NRC) and Electric Power Research Institute (EPRI) guidelines and applicable industry standards; it specifies the critical characteristics of the relays, provides the tests and analysis required to verify the critical characteristics, the acceptance criteria for the test results, performs source verification to quality P&B for its control of the critical characteristics, and provides documentation. The program provides reasonable assurance that the new MDR relays will perform their intended safety functions.

Cognitive Spectrum Efficient Multiple Access Technique using Relay Systems

DEFF Research Database (Denmark)

Frederiksen, Flemming Bjerge; Prasad, Ramjee

2007-01-01

Methods to enhance the use of the frequency spectrum by automatical spectrum sensing plus spectrum sharing in a cognitive radio technology context will be presented and discussed in this paper. Ideas to increase the coverage of cellular systems by relay channels, relay stations and collaborate...

Cooperative relay-based multicasting for energy and delay minimization

KAUST Repository

Atat, Rachad; Yaacoub, Elias E.; Alouini, Mohamed-Slim; Abu-Dayya, Adnan A.

2012-01-01

mobiles. Two schemes are investigated. The first consists of the BS sending the data only to the relay, and the second scheme considers the scenario of threshold-based multicasting by the BS, where a relay is selected to transmit the data to the mobiles

Massive MIMO Relay Systems with Multipair Wireless Information and Power Transfer

Directory of Open Access Journals (Sweden)

Hongwu Liu

2017-01-01

Full Text Available This paper investigates destination-aided simultaneous wireless information and power transfer (SWIPT for a decode-and-forward relay network, in which massive multiple-input multiple-output antennas are deployed at relay to assist communications among multiple source-destination pairs. During relaying, energy signals are emitted from multiple destinations when multiple sources are sending their information signals to relay. With power splitting and unlimited antennas at relay, asymptotic expression of harvested energy is derived. The analysis reveals that asymptotic harvested energy is independent of fast fading effect of wireless channels; meanwhile transmission powers of each source and destination can be scaled down inversely proportional to the number of relay antennas. To significantly reduce energy leakage interference and multipair interference, zero-forcing processing and maximum-ratio combing/maximum-ratio transmission are employed at relay. Fundamental trade-off between harvested energy and achievable sum rate is quantified. It is shown that asymptotic sum rate is neither convex nor concave with respect to power splitting and destination transmission power. Thus, a one-dimensional embedded bisection algorithm is proposed to jointly determine the optimal power splitting and destination transmission power. It shows that destination-aided SWIPT are beneficial for harvesting energy and increasing sum rate. The significant sum rate improvements of the proposed schemes are verified by numerical results.

CERN Relay Race: information for drivers

CERN Multimedia

2012-01-01

The CERN relay race will take place around the Meyrin site on Thursday, 24 May starting at 12.15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. In addition, there will be a Nordic Walking event which will finish around 12.50. This should not block the roads, but please drive carefully during this time. Thank you for your cooperation. Details on how to register your team for the relay race can be found here.

Improved Relay Node Placement Algorithm for Wireless Sensor Networks Application in Wind Farm

DEFF Research Database (Denmark)

Chen, Qinyin; Hu, Y.; Chen, Zhe

2013-01-01

-tolerance. Each wind turbine has a potentially large number of data points needing to be monitored and collected, as farms continue to increase in scale; distances between turbines can reach several hundred meters. Optimal placement of relays in a large farm requires an efficient algorithmic solution. A relay...... node placement algorithm is proposed in this paper to approximate the optimal position for relays connecting each turbine. However, constraints are then required to prevent relay nodes being overloaded in 3-dimensions. The algorithm is extended to 3-dimensional Euclidean space for this optimal relay...

Performance analysis of two-way amplify and forward relaying with adaptive modulation

KAUST Repository

Hwang, Kyusung

2009-09-01

In this paper, we study two-way amplify-and-forward relaying in conjunction with adaptive modulation over a multiple relay network. In order to keep the diversity order equal to the number of relays and maintain a low complexity, we consider the best relay selection scheme in this work. Based on the proposed selection criterion for the best relay, we analyze the average spectral efficiency by its approximated upper bound. In addition, we extend the proposed scheme to the case where a direct path between source and destination exists. Our numerical examples show that the proposed system offers a considerable gain in the spectral efficiency while satisfying the error rates requirements. ©2009 IEEE.

78 FR 21929 - Transmission Relay Loadability Reliability Standard; Notice of Compliance Filing

Science.gov (United States)

2013-04-12

... Relay Loadability Reliability Standard; Notice of Compliance Filing Take notice that on February 19... Relay Loadability Reliability Standard, Order No. 733, 130 FERC ] 61,221 (2010) (Order No. 733); order..., 136 FERC ] 61,185 (2011). \\2\\ Transmission Relay Loadability Reliability Standard, 138 FERC ] 61,197...

78 FR 55249 - Transmission Relay Loadability Reliability Standard; Notice of Compliance Filing

Science.gov (United States)

2013-09-10

...; RM11-16-000] Transmission Relay Loadability Reliability Standard; Notice of Compliance Filing Take.... \\1\\ Transmission Relay Loadability Reliability Standard, Order No. 733, 130 FERC ] 61, 221 (2010..., Order No. 733-B, 136 FERC ] 61,185 (2011). \\2\\ Transmission Relay Loadability Reliability Standard, 138...

Outage analysis for underlay relay-assisted cognitive networks

KAUST Repository

Tourki, Kamel; Qaraqe, Khalid A.; Alouini, Mohamed-Slim

2012-01-01

Cooperative relay technology was recently introduced into cognitive radio networks in order to enhance network capacity, scalability, and reliability of end-to-end communication. In this paper, we investigate an underlay cognitive network where the quality of service of the secondary link is maintained by triggering an opportunistic regenerative relaying once it falls under an unacceptable level. We first provide the exact cumulative density function (CDF) of received signal-to-noise (SNR) over each hop with co-located relays. Then, the CDFs are used to determine very accurate closed-form expression for the outage probability for a transmission rate R. We validate our analysis by showing that simulation results coincide with our analytical results in Rayleigh fading channels. © 2012 IEEE.

Outage analysis for underlay relay-assisted cognitive networks

KAUST Repository

Tourki, Kamel

2012-12-01

Cooperative relay technology was recently introduced into cognitive radio networks in order to enhance network capacity, scalability, and reliability of end-to-end communication. In this paper, we investigate an underlay cognitive network where the quality of service of the secondary link is maintained by triggering an opportunistic regenerative relaying once it falls under an unacceptable level. We first provide the exact cumulative density function (CDF) of received signal-to-noise (SNR) over each hop with co-located relays. Then, the CDFs are used to determine very accurate closed-form expression for the outage probability for a transmission rate R. We validate our analysis by showing that simulation results coincide with our analytical results in Rayleigh fading channels. © 2012 IEEE.

PERFORMANCE ANALYSIS OF COOPERATION SCHEMES IN EAVESDROPPER ASSISTED RELAY CHANNEL

Directory of Open Access Journals (Sweden)

Vaibhav Kumar Gupta

2014-06-01

Full Text Available The prominence of the wireless communication has been urging the monotonically increasing demand of security and privacy. In wireless systems, the notion of perfect secrecy of information with respect to illegitimate nodes can be ensured via physical layer security (PLS techniques. Unfortunately, they can be made less effective if source- eavesdropper wiretap channel is better than the main source-receiver channel. The various node cooperation schemes can be employed to combat this limitation where a relay node assists the communication to improve the performance significantly. In this paper, a four node wireless communication system consisting of a source, a destination, a relay and an eavesdropper as wire-tapper has been considered. The performance of the traditional cooperation schemes in terms of secrecy rate has been investigated with a different scenario where relay node helps the eavesdropper to deteriorate the secrecy rate. In addition, since legitimate receiver can overhear the transmission of relay, it favours the achievable secrecy rate. We formulate an analytical expression of conditional secrecy outage probability for the investigated system. From the obtained simulation results, it has been observed that secrecy rate is monotonically increases with path loss index. Furthermore, the proper selection of the system parameters leads to enhance the secrecy performance of the system even if relay pertains to degrade the performance. Amplify-and-forward, cooperation, decode-and-Forward, secrecy rate, relay.

Relay selection in cooperative communication systems over continuous time-varying fading channel

Directory of Open Access Journals (Sweden)

Ke Geng

2017-02-01

Full Text Available In this paper, we study relay selection under outdated channel state information (CSI in a decode-and-forward (DF cooperative system. Unlike previous researches on cooperative communication under outdated CSI, we consider that the channel varies continuously over time, i.e., the channel not only changes between relay selection and data transmission but also changes during data transmission. Thus the level of accuracy of the CSI used in relay selection degrades with data transmission. We first evaluate the packet error rate (PER of the cooperative system under continuous time-varying fading channel, and find that the PER performance deteriorates more seriously under continuous time-varying fading channel than when the channel is assumed to be constant during data transmission. Then, we propose a repeated relay selection (RRS strategy to improve the PER performance, in which the forwarded data is divided into multiple segments and relay is reselected before the transmission of each segment based on the updated CSI. Finally, we propose a combined relay selection (CRS strategy which takes advantage of three different relay selection strategies to further mitigate the impact of outdated CSI.

Hybrid reed: Solid-state devices are a new generation of protective relays

Directory of Open Access Journals (Sweden)

Gurevich Vladimir

2007-01-01

Full Text Available Research and development in the field of electromechanical protective relays has not been conducted for tens of years. Author’s approach allows viewing the problem of re-equipment of relay protection in a new way. In the author’s opinion combination of reed switches with magnetic circuits and semiconductor elements opens new avenues in development of the promising protective relays featuring reliability, simplicity and low cost. Examples of protective relays made with these elements are given below.

Minimax robust relay selection based on uncertain long-term CSI

KAUST Repository

Nisar, Muhammad Danish; Alouini, Mohamed-Slim

2014-01-01

Cooperative communications via multiple relay nodes is known to provide the benefits of increase diversity and coverage. Simultaneous transmission via multiple relays, however, requires strong coordination between nodes either in terms of slot

On full duplex Gaussian relay channels with self-interference

KAUST Repository

Behboodi, Arash

2016-08-15

Self interference (SI) in full duplex (FD) systems is the interference caused by the transmission stream on the reception stream. Being one of the main restrictive factors for performance of practical full duplex systems, however, not too much is known about its effect on the fundamental limits of relaying systems. In this work, we consider the full duplex three-node relay channel with SI where SI is modeled as an additive Gaussian noise whose variance is dependent on instantaneous input power. The classical achievable rates and upper bounds for the single three-node relay channel no longer apply due to the structure of SI. Achievable rates for Decode-and-Forward (DF) and Compress-and-Forward (CF) and upper bounds on the capacity are derived assuming Gaussian inputs and SI. The deterministic model is also introduced and its capacity is characterized. The optimal joint source-relay distributions is discussed. Numerical results are provided comparing the achievable rates and upper bound. © 2016 IEEE.

Superimposed Training-Based Channel Estimation for MIMO Relay Networks

Directory of Open Access Journals (Sweden)

Xiaoyan Xu

2012-01-01

Full Text Available We introduce the superimposed training strategy into the multiple-input multiple-output (MIMO amplify-and-forward (AF one-way relay network (OWRN to perform the individual channel estimation at the destination. Through the superposition of a group of additional training vectors at the relay subject to power allocation, the separated estimates of the source-relay and relay-destination channels can be obtained directly at the destination, and the accordance with the two-hop AF strategy can be guaranteed at the same time. The closed-form Bayesian Cramér-Rao lower bound (CRLB is derived for the estimation of two sets of flat-fading MIMO channel under random channel parameters and further exploited to design the optimal training vectors. A specific suboptimal channel estimation algorithm is applied in the MIMO AF OWRN using the optimal training sequences, and the normalized mean square error performance for the estimation is provided to verify the Bayesian CRLB results.

Selection combining for noncoherent decode-and-forward relay networks

Directory of Open Access Journals (Sweden)

Nguyen Ha

2011-01-01

Full Text Available Abstract This paper studies a new decode-and-forward relaying scheme for a cooperative wireless network composed of one source, K relays, and one destination and with binary frequency-shift keying modulation. A single threshold is employed to select retransmitting relays as follows: a relay retransmits to the destination if its decision variable is larger than the threshold; otherwise, it remains silent. The destination then performs selection combining for the detection of transmitted information. The average end-to-end bit-error-rate (BER is analytically determined in a closed-form expression. Based on the derived BER, the problem of choosing an optimal threshold or jointly optimal threshold and power allocation to minimize the end-to-end BER is also investigated. Both analytical and simulation results reveal that the obtained optimal threshold scheme or jointly optimal threshold and power-allocation scheme can significantly improve the BER performance compared to a previously proposed scheme.

Novel half-coherent receivers for amplify-and-forward relaying

KAUST Repository

Khan, Fahd Ahmed

2012-06-01

Consider a system in which the signal is transmitted from the source to the destination via an amplify-and-forward relay. For such a system, we derive in this paper, novel receivers that have complete knowledge of either the source-relay link or the relay-destination link. These receivers are termed as, \\'half-coherent receivers\\' as they have channel-state-information (CSI) of only one of two links. These receivers can be very useful in a system in which only the relay can afford high complexity by having a channel estimation module and the destination is unable to support channel estimation or a system in which only the destination can afford higher complexity and includes the channel estimation module. The analytical bit-error-rate (BER) performances of the proposed receivers are derived for Rician fading. Numerical results show considerable performance gains of the new receivers, especially at low signal-to-noise ratio. © 2012 IEEE.

Relay-Assisted Primary and Secondary Transmissions in Cognitive Radio Networks

KAUST Repository

Shafie, Ahmed El

2016-09-27

We assume a set of cognitive relay nodes that assists both primary and secondary transmissions in a time-slotted cognitive radio networks. To regulate the channel access of the various nodes in the network, we propose an overlapped spectrum sensing strategy for channel sensing, where the secondary source node senses the channel from the beginning of the time slot and the cognitive relay nodes sense the channel for double the sensing time used by the secondary source node to detect the activities of both the primary and secondary source nodes. Hence, the secondary source node has an intrinsic priority over the relay nodes. The relay nodes help both the primary user and the secondary user to deliver their unsuccessfully decoded packets at their destinations. In a given time slot, the scheduled relay node for data transmission starts its transmission when both the primary and secondary users are sensed to be inactive (i.e. have no data to transmit). We propose two optimization-based formulations with quality-of-service (QoS) constraints involving average queueing delay and average service rate requirements. We investigate both cases of perfect and imperfect spectrum sensing. To further enhance the users\\' QoS requirements, we propose three packet decoding strategies at the relay nodes and compare their performance. We derive an upper bound on the secondary queue average service rate to determine which decoding strategy can achieve that bound. Our numerical results show the benefits of relaying and its ability to enhance the performance of both the primary and secondary users. Moreover, the performance of the proposed schemes is close to the derived upper bound.

Self-oscillations in dynamic systems a new methodology via two-relay controllers

CERN Document Server

Aguilar, Luis T; Fridman, Leonid; Iriarte, Rafael

2015-01-01

This monograph presents a simple and efficient two-relay control algorithm for generation of self-excited oscillations of a desired amplitude and frequency in dynamic systems. Developed by the authors, the two-relay controller consists of two relays switched by the feedback received from a linear or nonlinear system, and represents a new approach to the self-generation of periodic motions in underactuated mechanical systems. The first part of the book explains the design procedures for two-relay control using three different methodologies – the describing-function method, Poincaré maps, and the locus-of-a perturbed-relay-system method – and concludes with stability analysis of designed periodic oscillations. Two methods to ensure the robustness of two-relay control algorithms are explored in the second part, one based on the combination of the high-order sliding mode controller and backstepping, and the other on higher-order sliding-modes-based reconstruction of uncertainties and their compensation where...

Xenon-ion-induced and thermal mixing of Co/Si bilayers and their interplay

Energy Technology Data Exchange (ETDEWEB)

Novakovic, M. [VINCA Institute of Nuclear Sciences, 11001 Belgrade (Serbia); II. Physikalisches Institut, Georg-August-Universitaet Goettingen, Friedrich-Hund-Platz 1, 37077 Goettingen (Germany); Zhang, K. [II. Physikalisches Institut, Georg-August-Universitaet Goettingen, Friedrich-Hund-Platz 1, 37077 Goettingen (Germany); Popovic, M.; Bibic, N. [VINCA Institute of Nuclear Sciences, 11001 Belgrade (Serbia); II. Physikalisches Institut, Georg-August-Universitaet Goettingen, Friedrich-Hund-Platz 1, 37077 Goettingen (Germany); Hofsaess, H. [II. Physikalisches Institut, Georg-August-Universitaet Goettingen, Friedrich-Hund-Platz 1, 37077 Goettingen (Germany); Lieb, K.P., E-mail: plieb@gwdg.d [II. Physikalisches Institut, Georg-August-Universitaet Goettingen, Friedrich-Hund-Platz 1, 37077 Goettingen (Germany)

2011-05-01

Studies on ion-irradiated transition-metal/silicon bilayers demonstrate that interface mixing and silicide phase formation depend sensitively on the ion and film parameters, including the structure of the metal/Si interface. Thin Co layers e-gun evaporated to a thickness of 50 nm on Si(1 0 0) wafers were bombarded at room temperature with 400-keV Xe{sup +} ions at fluences of up to 3 x 10{sup 16} cm{sup -2}. We used either crystalline or pre-amorphized Si wafers the latter ones prepared by 1.0-keV Ar-ion implantation. The as-deposited or Xe-ion-irradiated samples were then isochronally annealed at temperatures up to 700 {sup o}C. Changes of the bilayer structures induced by ion irradiation and/or annealing were investigated with RBS, XRD and HRTEM. The mixing rate for the Co/c-Si couples, {Delta}{sigma}{sup 2}/{Phi} = 3.0(4) nm{sup 4}, is higher than the value expected for ballistic mixing and about half the value typical for spike mixing. Mixing of pre-amorphized Si is much weaker relative to crystalline Si wafers, contrary to previous results obtained for Fe/Si bilayers. Annealing of irradiated samples produces very similar interdiffusion and phase formation patterns above 400 {sup o}C as in the non-irradiated Co/Si bilayers: the phase evolution follows the sequence Co{sub 2}Si {yields} CoSi {yields} CoSi{sub 2}.

Influence of interdiffusion on the magnetic properties of Co/Si (100) films after high magnetic field annealing

International Nuclear Information System (INIS)

Zhao, Yue; Wang, Kai; Wang, Qiang; Li, Guojian; Lou, Changsheng; Pang, Hongxuan; He, Jicheng

2015-01-01

The influence of interdiffusion on the magnetic properties of Co/Si (100) films after thermal annealing in the presence of a strong magnetic field was investigated. The interdiffusion coefficients of films that were annealed at temperatures of 380 °C and 420 °C in the presence of high magnetic fields were not affected. However, the interdiffusion coefficient of films annealed at 400 °C in the presence of a high magnetic field decreased significantly. The change in the interdiffusion coefficient, caused by high magnetic field annealing, increased the content of the magnetic phase. This increase in the magnetic phase improved the saturation magnetization. A new method of high magnetic field annealing is presented that can modulate the diffusion and magnetic properties of thin films. - Highlights: • Interdiffusion of Co/Si (100) films by high magnetic field annealing was studied. • Thickness of the diffusion layer was reduced by magnetic field annealing at 400 °C. • Interdiffusion coefficient decreased following magnetic field annealing at 400 °C. • Saturation magnetization increased after high magnetic field annealing at 400 °C

Susceptibility of modern relay protection: Will protection from cyber attacks help?

Directory of Open Access Journals (Sweden)

Gurevich Vladimir

2014-01-01

Full Text Available Modern trends in relay protection (RP based on the substitution of electromechanical protection relays (EMPR by digital protective relays (DPR have resulted in the emergence of an absolutely new problem, which was not known before. This problem is the possibility of an intentional remote destructive impact (IRDI on relay protection in order to put it out of action or make it perform functions that have nothing to do with the current operational mode of protected electric equipment. Traditional and well-known methods ensuring information safety cannot fully prevent unauthorized actions of RP. The article describes a new way for the problem solution.

Low Complexity Transmission Scheme with Full Diversity for Two-Path Relay Networks

KAUST Repository

Fareed, Muhammad Mehboob

2014-01-06

In this work, we present a new low complexity scheme for two-path relay network to harvest maximum achievable diversity. We analyze the performance of the newly proposed two-path relay network by calculating the symbol error rate (SER) for arbitrary location of relays. It is shown that with this newly proposed scheme, two-path relay networks can mimic a 2x2 multiple-input mulitple-output (MIMO) system and achieve full diversity order of four. Simulations results are provided to verify and illustrate the analytical results.

Low Complexity Transmission Scheme with Full Diversity for Two-Path Relay Networks

KAUST Repository

Fareed, Muhammad Mehboob; Yang, Hong-Chuan; Alouini, Mohamed-Slim

2014-01-01

In this work, we present a new low complexity scheme for two-path relay network to harvest maximum achievable diversity. We analyze the performance of the newly proposed two-path relay network by calculating the symbol error rate (SER) for arbitrary location of relays. It is shown that with this newly proposed scheme, two-path relay networks can mimic a 2x2 multiple-input mulitple-output (MIMO) system and achieve full diversity order of four. Simulations results are provided to verify and illustrate the analytical results.

protective relay studies for the nigerian national electric 330 kv

African Journals Online (AJOL)

user

1985-09-01

Sep 1, 1985 ... protective relay schemes of the National Electric Power Authority. Some of the basic ... Nigerian special system characteristics, schemes to correct existing protection inadequacies .... relays buried in the transformer. A reach of ...

Adjustable electronic load-alarm relay

International Nuclear Information System (INIS)

Mason, C.H.; Sitton, R.S.

1976-01-01

An improved electronic alarm relay for monitoring the current drawn by an ac motor or other electrical load is described. The circuit is designed to measure the load with high accuracy and to have excellent alarm repeatability. Chattering and arcing of the relay contacts are minimal. The operator can adjust the set point easily and can re-set both the high and the low alarm points by means of one simple adjustment. The relay includes means for generating a signal voltage proportional to the motor current. In a preferred form of the invention a first operational amplifier is provided to generate a first constant reference voltage which is higher than a preselected value of the signal voltage. A second operational amplifier is provided to generate a second constant reference voltage which is lower than the aforementioned preselected value of the signal voltage. A circuit comprising a first resistor serially connected to a second resistor is connected across the outputs of the first and second amplifiers, and the junction of the two resistors is connected to the inverting terminal of the second amplifier. Means are provided to compare the aforementioned signal voltage with both the first and second reference voltages and to actuate an alarm if the signal voltage is higher than the first reference voltage or lower than the second reference voltage

Next-Generation NASA Earth-Orbiting Relay Satellites: Fusing Optical and Microwave Communications

Science.gov (United States)

Israel, David J.; Shaw, Harry

2018-01-01

NASA is currently considering architectures and concepts for the generation of relay satellites that will replace the Tracking and Data Relay Satellite (TDRS) constellation, which has been flying since 1983. TDRS-M, the last of the second TDRS generation, launched in August 2017, extending the life of the TDRS constellation beyond 2030. However, opportunities exist to re-engineer the concepts of geosynchronous Earth relay satellites. The needs of the relay satellite customers have changed dramatically over the last 34 years since the first TDRS launch. There is a demand for greater bandwidth as the availability of the traditional RF spectrum for space communications diminishes and the demand for ground station access grows. The next generation of NASA relay satellites will provide for operations that have factored in these new constraints. In this paper, we describe a heterogeneous constellation of geosynchronous relay satellites employing optical and RF communications. The new constellation will enable new optical communications services formed by user-to-space relay, space relay-to-space relay and space relay-to-ground links. It will build upon the experience from the Lunar Laser Communications Demonstration from 2013 and the Laser Communications Relay Demonstration to be launched in 2019.Simultaneous to establishment of the optical communications space segment, spacecraft in the TDRS constellation will be replaced with RF relay satellites with targeted subsets of the TDRS capabilities. This disaggregation of the TDRS service model will allow for flexibility in replenishing the needs of legacy users as well as addition of new capabilities for future users. It will also permit the U.S. government access to launch capabilities such as rideshare and to hosted payloads that were not previously available.In this paper, we also explore how the next generation of Earth relay satellites provides a significant boost in the opportunities for commercial providers to the

Next-Generation NASA Earth-Orbiting Relay Satellites: Fusing Microwave and Optical Communications

Science.gov (United States)

Israel, David J.

2018-01-01

NASA is currently considering architectures and concepts for the generation of relay satellites that will replace the Tracking and Data Relay Satellite (TDRS) constellation, which has been flying since 1983. TDRS-M, the last of the second TDRS generation, launched in August 2017, extending the life of the TDRS constellation beyond 2030. However, opportunities exist to re-engineer the concepts of geosynchronous Earth relay satellites. The needs of the relay satellite customers have changed dramatically over the last 34 years since the first TDRS launch. There is a demand for greater bandwidth as the availability of the traditional RF spectrum for space communications diminishes and the demand for ground station access grows. The next generation of NASA relay satellites will provide for operations that have factored in these new constraints. In this paper, we describe a heterogeneous constellation of geosynchronous relay satellites employing optical and RF communications. The new constellation will enable new optical communications services formed by user-to-space relay, space relay-to-space relay and space relay-to-ground links. It will build upon the experience from the Lunar Laser Communications Demonstration from 2013 and the Laser Communications Relay Demonstration to be launched in 2019.Simultaneous to establishment of the optical communications space segment, spacecraft in the TDRS constellation will be replaced with RF relay satellites with targeted subsets of the TDRS capabilities. This disaggregation of the TDRS service model will allow for flexibility in replenishing the needs of legacy users as well as addition of new capabilities for future users. It will also permit the U.S. government access to launch capabilities such as rideshare and to hosted payloads that were not previously available. In this paper, we also explore how the next generation of Earth relay satellites provides a significant boost in the opportunities for commercial providers to the

Near optimal power allocation algorithm for OFDM-based cognitive using adaptive relaying strategy

KAUST Repository

Soury, Hamza; Bader, Faouzi; Shaat, Musbah M R; Alouini, Mohamed-Slim

2012-01-01

Relayed transmission increases the coverage and achievable capacity of communication systems. Adaptive relaying scheme is a relaying technique by which the benefits of the amplifying or decode and forward techniques can be achieved by switching the forwarding technique according to the quality of the signal. A cognitive Orthogonal Frequency-Division Multiplexing (OFDM) based adaptive relaying protocol is considered in this paper. The objective is to maximize the capacity of the cognitive radio system while ensuring that the interference introduced to the primary user is below the tolerated limit. A Near optimal power allocation in the source and the relay is presented for two pairing techniques such that the matching and random pairing. The simulation results confirm the efficiency of the proposed adaptive relaying protocol, and the consequence of choice of pairing technique. © 2012 ICST.

Simultaneous Wireless Information and Power Transfer for MIMO Amplify-and-Forward Relay Systems

KAUST Repository

Benkhelifa, Fatma; Alouini, Mohamed-Slim

2016-01-01

In this paper, we investigate the simultaneous wireless information and power transfer (SWIPT) for the two-hop Multiple-Input Multiple-Output (MIMO) Amplify-and-Forward (AF) relay communication systems with the multiantenna energy harvesting relay. We derive the optimal source and relay covariance matrices to characterize the achievable region between the sourcedestination rate and the harvested energy at the relay, namely Rate-Energy (R-E) region. In this context, we consider the ideal scenario where the energy harvester (EH) receiver and the information decoder (ID) receiver at the relay can simultaneously decode the information and harvest the energy at the relay. Then, we consider more practical schemes which are the power splitting (PS) and the time switching (TS) which separate the EH and ID transfer over the power domain and the time domain, respectively.

Simultaneous Wireless Information and Power Transfer for MIMO Amplify-and-Forward Relay Systems

KAUST Repository

Benkhelifa, Fatma

2016-01-06

In this paper, we investigate the simultaneous wireless information and power transfer (SWIPT) for the two-hop Multiple-Input Multiple-Output (MIMO) Amplify-and-Forward (AF) relay communication systems with the multiantenna energy harvesting relay. We derive the optimal source and relay covariance matrices to characterize the achievable region between the sourcedestination rate and the harvested energy at the relay, namely Rate-Energy (R-E) region. In this context, we consider the ideal scenario where the energy harvester (EH) receiver and the information decoder (ID) receiver at the relay can simultaneously decode the information and harvest the energy at the relay. Then, we consider more practical schemes which are the power splitting (PS) and the time switching (TS) which separate the EH and ID transfer over the power domain and the time domain, respectively.

Enhancing overcurrent relay performance using wavelet packet transform

International Nuclear Information System (INIS)

Adly, A.R.

2012-01-01

The function of a power system relaying is to cause the prompt removal of any element of power system from service when it is subjected to short circuit or it starts to operate in any abnormal manner that might cause damage or otherwise interfere with the effective operation of the rest of the system. Overcurrent protection is one of the most widely used relays in power system which is used for both primary and back-up protective relays, and applied in every protective zone in the system. The application of time overcurrent relays in power system presents serious limitations in terms of sensitivity and selectivity. Digital forms of such relays are being mostly used which have the advantages of data recording and adaptive features. This thesis introduces a technique based on Wavelet Packet Transform (WPT) to detect short circuit faults within wide variation in generating conditions, with very small voltage variation, and High-Impedance Faults (HIFs). Besides, it examines the load current continuously and changes the relay pick up value adaptively. WPT is used to estimate proper value for the RMS fundamental and hence calculate trip time accurately even that when the signals have been contaminated with other harmonics, inter harmonics or subharmonic. Simulation work was conducted using Alternative Transient Program (ATP) package. A radial distribution system and series compensated line are modeled as case studies. The performance of the proposed overcurrent scheme for both lines is extensively tested during different operating conditions including; normal, internal short circuit faults, HIFs and similar situations to HIFs: such as capacitor switching (in), capacitor switching (out), load switching, and no load line switching. This thesis also uses a technique that estimates the location of short circuit faults on a radial distribution system. The technique was tested to evaluate its suitability. The results indicate that the proposed technique works well. It also

Impact Analysis of Electrical Current Characteristics in Relay Function for Electrical and Electronic Protection

International Nuclear Information System (INIS)

Syirrazie Che Soh; Harzawadi Hasim

2013-01-01

This paper is to study effect of electrical current on relay reaction, which has coil and switch inside the relay. An analysis on the electrical current will be conducted to determine current limitation for relay activation purpose. The result of analysis showing that current characteristic of relay and applied load will present their affect to the relay function performance. Finding from this result will bring the idea to develop a suitable design circuit for electrical and electronic protection. (author)

Light meson production and pp-bremsstrahlung at the COSY time-of-flight spectrometer

International Nuclear Information System (INIS)

Kuhlmann, E.; Brand, H.; Brand, S.; Cloth, P.; Dahmen, M.; Drueke, V.; Eyrich, W.; Filges, D.; Freiesleben, H.; Fritsche, A.; Kilian, K.; Kirsch, M.; Koch, H.; Kraft, R.A.; Krug, J.; Lange, S.; Machner, H.; Matthaey, H.; Michel, P.; Mirz, R.; Moeller, K.; Morsch, H.P.; Naumann, B.; Naumann, L.; Oelert, W.; Parsch, A.; Paul, N.; Ringe, P.; Roderburg, E.; Roehrich, K.; Roeser, A.; Rogge, M.; Schmidt, G.; Schmidt, M.; Schult, O.; Sefzick, T.; Steinke, M.; Stinzing, F.; Stratmann, R.; Turek, P.; Werding, R.; Wirth, S.

1993-01-01

Experiments on light meson production and pp-bremsstrahlung as planned for the initial stage at COSY are discussed. Special emphasis will be placed on near-threshold behaviour where due to kinematics all particles are forced into a rather narrow cone around the beam axis. A specially designed charged particle detector system will be used which not only covers the complete forward hemisphere of 2π in the laboratory system but additionally shows maximum resolution in the extreme forward direction with only moderate cuts in the minimally required energy of all ejectiles. (orig.)

On achievable rates of interference and cognitive channels with a relay

KAUST Repository

Zorgui, Marwen; Rezki, Zouheir; Alouini, Mohamed-Slim

2015-01-01

We consider a two-user interference channel assisted by a relay. Treating interference as noise at the receivers, and adopting an amplify and forward (AF) strategy at the relay, we derive achievable rates of both users, for given powers. Next, we solve the optimal power allocation problem maximizing the weighted sum rate of both users with and without relay power optimization. In particular, we propose a simple iterative line search algorithm solving the joint optimization problem over the three transmit powers and show that optimizing the relay power enhances the performance of the system. Then, considering the first user as a primary user, we determine the maximum instantaneous rate that the secondary user can achieve subject to an outage constraint with respect to the primary user and a peak power constraint. We show that, likewise the first part, jointly optimizing the secondary user and the relay transmit powers enhances the secondary user performance.

On achievable rates of interference and cognitive channels with a relay

KAUST Repository

Zorgui, Marwen

2015-08-30

We consider a two-user interference channel assisted by a relay. Treating interference as noise at the receivers, and adopting an amplify and forward (AF) strategy at the relay, we derive achievable rates of both users, for given powers. Next, we solve the optimal power allocation problem maximizing the weighted sum rate of both users with and without relay power optimization. In particular, we propose a simple iterative line search algorithm solving the joint optimization problem over the three transmit powers and show that optimizing the relay power enhances the performance of the system. Then, considering the first user as a primary user, we determine the maximum instantaneous rate that the secondary user can achieve subject to an outage constraint with respect to the primary user and a peak power constraint. We show that, likewise the first part, jointly optimizing the secondary user and the relay transmit powers enhances the secondary user performance.

On the malfunction of disk-type induction relay under seismic condition

International Nuclear Information System (INIS)

Fujita, T.; Shibata, H.; Koizumi, T.

1985-01-01

This paper deals with the malfunction of disk-type induction relay. Equations of motion for rotational movement of induction relay was formulated and the dynamic behavior was simulated under various kind of exciting conditions. Experimental verification was also performed using two dimensional shaker table for some actual relays. Sufficient agreement was recognized between experimental and analytical results and consequently the most critical reason to cause the malfunction was pointed out. (orig.)

Optimal Coordination of Distance and Directional Overcurrent Relays Considering Different Network Topologies

Directory of Open Access Journals (Sweden)

Y. Damchi

2015-09-01

Full Text Available Most studies in relay coordination have focused solely on coordination of overcurrent relays while distance relays are used as the main protection of transmission lines. Since, simultaneous coordination of these two types of relays can provide a better protection, in this paper, a new approach is proposed for simultaneous coordination of distance and directional overcurrent relays (D&DOCRs. Also, pursued by most of the previously published studies, the settings of D&DOCRs are usually determined based on a main network topology which may result in mis-coordination of relays when changes occur in the network topology. In the proposed method, in order to have a robust coordination, network topology changes are taken into account in the coordination problem. In the new formulation, coordination constraints for different network topologies are added to those of the main topology. A complex nonlinear optimization problem is derived to find the desirable relay settings. Then, the problem is solved using hybridized genetic algorithm (GA with linear programming (LP method (HGA. The proposed method is evaluated using the IEEE 14-bus test system. According to the results, a feasible and robust solution is obtained for D&DOCRs coordination while all constraints, which are due to different network topologies, are satisfied.

Transmission Power Adaption for Full-Duplex Relay-Aided Device-to-Device Communication

Directory of Open Access Journals (Sweden)

Hui Dun

2017-03-01

Full Text Available Device-to-device (D2D communications bring significant improvements of spectral efficiency by underlaying cellular networks. However, they also lead to a more deteriorative interference environment for cellular users, especially the users in severely deep fading or shadowing. In this paper, we investigate a relay-based communication scheme in cellular systems, where the D2D communications are exploited to aid the cellular downlink transmissions by acting as relay nodes with underlaying cellular networks. We modeled two-antenna infrastructure relays employed for D2D relay. The D2D transmitter is able to transmit and receive signals simultaneously over the same frequency band. Then we proposed an efficient power allocation algorithm for the base station (BS and D2D relay to reduce the loopback interference which is inherent due to the two-antenna infrastructure in full-duplex (FD mode. We derived the optimal power allocation problem in closed form under the independent power constraint. Simulation results show that the algorithm reduces the power consumption of D2D relay to the greatest extent and also guarantees cellular users’ minimum transmit rate. Moreover, it also outperforms the existing half-duplex (HD relay mode in terms of achievable rate of D2D.

Commissioning of the vacuum straw tracker for the COSY-TOF spectrometer

Energy Technology Data Exchange (ETDEWEB)

Roeder, Matthias; Ritman, James; Voigtlaender, Pierre; Wintz, Peter [Institut fuer Kernphysik I, Forschungszentrum Juelich GmbH (Germany)

2009-07-01

The Straw-Tracker at COSY-TOF is a system of 3120 Straws arranged in 30 layers. These are operated at 1.2 bar drift-gas pressure in the TOF vacuum so that they are self-supporting, despite their mylar wrapping being only 30 {mu}m thick. As a result the total radiation length amounts to only 1 %. The operation with 1500 V anode voltage in medium vacuum at {approx}5.10{sup -3} mbar imposes stringent demands on detector design and handling. In this talk the system is introduced and it is reported on the commissioning during the year 2008. The emphasis is placed on vacuum operation and results on the efficiency and resolution under experiment conditions.

Low-Complexity Combining Schemes in Dual-Hop AF Relaying Systems

KAUST Repository

Gaaloul, Fakhreddine; Alouini, Mohamed-Slim; Radaydeh, Redha M.

2011-01-01

This paper investigates the performance of different low-complexity combining schemes in the context of dual-hop amplify-and-forward (AF) relaying networks. It is assumed that the relay uses single transmit (receive) antenna due to space limitation

IE Information Notice No. 85-82: Diesel generator differential protection relay not seismically qualified

International Nuclear Information System (INIS)

Jordan, E.L.

1992-01-01

Licensees of BWR and PWR nuclear generating stations have reported using a high-speed differential protection relay that has been declared by the manufacturer to be not seismically qualified for the service intended. The relay, GE Model 12CFD, which is being used for emergency diesel generator protection against electrical shorts and grounds at the generator output, has not been seismically qualified to operate in the de-energized state for this application. Generally, the relay operates in the de-energized position before EDG operation. However, it then operates in the energized position whenever the EDG provides an electrical output to essential Class IE components. The safety concern of this issue involves an inadvertent activation of the normally de-energized relay from a seismic event. Momentary activation of the relay, in the circuits examined, blocks the automatic start feature of the EDG during certain emergency plant conditions through operation of another relay in the system. The NRC review of the problems concluded that the relays should be seismically qualified in their energized and de-energized states to preclude their spurious activation during a seismic event. Additionally, review of GE's GER 3069 report, ''Relay Protection of Class IE Systems,'' shows that the 12CFD differential relays were successfully tested for 3.5 g in the energized modes and only 0.75 g in the de-energized mode. Review of GE's GER 3069 report also revealed that GE type IJD differential relays do meet seismic requirements in all modes of operation mentioned above and is the GE recommendation for replacement of the differential relay in question

Implementing Strategic Planning Capabilities Within the Mars Relay Operations Service

Science.gov (United States)

Hy, Franklin; Gladden, Roy; Allard, Dan; Wallick, Michael

2011-01-01

Since the Mars Exploration Rovers (MER), Spirit and Opportunity, began their travels across the Martian surface in January of 2004, orbiting spacecraft such as the Mars 2001 Odyssey orbiter have relayed the majority of their collected scientific and operational data to and from Earth. From the beginning of those missions, it was evident that using orbiters to relay data to and from the surface of Mars was a vastly more efficient communications strategy in terms of power consumption and bandwidth compared to direct-to-Earth means. However, the coordination between the various spacecraft, which are largely managed independently and on differing commanding timelines, has always proven to be a challenge. Until recently, the ground operators of all these spacecraft have coordinated the movement of data through this network using a collection of ad hoc human interfaces and various, independent software tools. The Mars Relay Operations Service (MaROS) has been developed to manage the evolving needs of the Mars relay network, and specifically to standardize and integrate the relay planning and coordination data into a centralized infrastructure. This paper explores the journey of developing the MaROS system, from inception to delivery and acceptance by the Mars mission users.

Outage Probability Analysis in Power-Beacon Assisted Energy Harvesting Cognitive Relay Wireless Networks

Directory of Open Access Journals (Sweden)

Ngoc Phuc Le

2017-01-01

Full Text Available We study the performance of the secondary relay system in a power-beacon (PB assisted energy harvesting cognitive relay wireless network. In our system model, a secondary source node and a relay node first harvest energy from distributed PBs. Then, the source node transmits its data to the destination node with the help of the relay node. Also, fading coefficients of the links from the PBs to the source node and relay node are assumed independent but not necessarily identically distributed (i.n.i.d Nakagami-m random variables. We derive exact expressions for the power outage probability and the channel outage probability. Based on that, we analyze the total outage probability of the secondary relay system. Asymptotic analysis is also performed, which provides insights into the system behavior. Moreover, we evaluate impacts of the primary network on the performance of the secondary network with respect to the tolerant interference threshold at the primary receiver as well as the interference introduced by the primary transmitter at the secondary source and relay nodes. Simulation results are provided to validate the analysis.

Achievable Rates of Buffer-Aided Full-Duplex Gaussian Relay Channels

KAUST Repository

El Shafie, Ahmed

2017-10-18

We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multipleoutput (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

Achievable Rates of Buffer-Aided Full-Duplex Gaussian Relay Channels

KAUST Repository

El Shafie, Ahmed; Salem, Ahmed Sultan; Krikidis, Ioannis; Al-Dhahir, Naofal; Hamila, Ridha

2017-01-01

We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multipleoutput (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

Simultaneous Wireless Information and Power Transfer Mechanism in Interference Alignment Relay Networks

Directory of Open Access Journals (Sweden)

Fahui Wu

2016-01-01

Full Text Available This paper considers a simultaneous wireless information and power transfer (SWIPT mechanism in an interference alignment (IA relay system, in which source nodes send wireless information and energy simultaneously to relay nodes, and relay nodes forward the received signal to destination nodes powered by harvested energy. To manage interference and utilize interference as energy source, two-SWIPT receiver is designed, namely, power splitting (PS, and antennas switching (AS has been considered for relay system. The performance of AS- and PS-based IA relay systems is considered, as is a new energy cooperation (ECop scheme that is proposed to improve system performance. Numerical results are provided to evaluate the performance of all schemes and it is shown from the simulations that the performance of proposed ECop outperformed both AS and PS.

Rate regions for coordination of Decode-and-Forward relays and direct users

DEFF Research Database (Denmark)

Thai, Chan; Popovski, Petar

2012-01-01

Recently, the ideas of wireless network coding (NC) has significantly enriched the area of wireless cooperation/relaying. They bring substantial gains in spectral efficiency mainly in scenarios with two–way relaying. Inspired by the ideas of wireless NC, recently we have proposed techniques...... for coordinated direct/relay (CDR) transmissions. Leveraging on the fact that the interference can be subsequently canceled, these techniques embrace the interference among the communication flows to/from direct and relayed users. Hence, by allowing simultaneous transmissions, spectral efficiency is increased....... In our prior work, we have proposed CDR with Decode–and–Forward (DF) relay in two scenarios. In this paper, we extend the two existing regenerative CDR schemes and proposed for the other two scenarios such that all schemes benefit from the aforementioned principle of containing the interference...

Multistability and hidden attractors in a relay system with hysteresis

DEFF Research Database (Denmark)

Zhusubaliyev, Zhanybai T.; Mosekilde, Erik; Rubanov, Vasily G.

2015-01-01

with the neighborhood of that cycle. We show how the equilibrium point of a relay system disappears in a boundary-equilibrium bifurcation as the system enters the region of autonomous switching dynamics and demonstrate experimentally how a relay system can exhibit large amplitude chaotic oscillations at high values...... of the supply voltage. By investigating a four-dimensional model of the experimental relay system we finally show how a variety of hidden periodic, quasiperiodic and chaotic attractors arise, transform and disappear through different bifurcations. (C) 2015 Elsevier B.V. All rights reserved....

Synthesis of relay control systems for nuclear reactors

International Nuclear Information System (INIS)

Postnikov, N.S.

1996-01-01

The problem on stabilizing an oscillatory-unstable reactor by a single-link relay system, the characteristics whereof have a dead zone and hysteresis loop, is considered. The methodology of synthesis of feedback law, providing for stochastic steady-state mode of reactor operation with the minimum frequency of control impact introduction is proposed. This methodology is applicable to general-type relay systems with arbitrary oscillatory-unstable objects. 6 refs., 5 figs

Simultaneous Wireless Information and Power Transfer for MIMO Amplify-and-Forward Relay Systems

KAUST Repository

Benkhelifa, Fatma; Alouini, Mohamed-Slim

2016-01-01

relay. We derive the optimal source and relay covariance matrices to characterize the achievable region between the source-destination rate and the harvested energy at the relay, namely Rate-Energy (R-E) region. In this context, we consider the ideal

Interference alignment for degrees of freedom improvement in 3-relay half-duplex systems

KAUST Repository

Park, Seongho; Ko, Youngchai; Park, Kihong; Alouini, Mohamed-Slim

2011-01-01

In a half-duplex relaying, the capacity pre-log factor is a major drawback in spectral efficiency. This paper proposes a linear precoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help

Uplink Capacity of 802.16j Mobile Multihop Relay Networks with Transparent Relays

DEFF Research Database (Denmark)

Wang, Hua; Andrews, Jeffrey G.; Iversen, Villy Bæk

2009-01-01

-to-end spectral efficiency. Furthermore, the position and the number of relay stations (RSs) have a great impact on the capacity gain. These results are further verified in the evaluation of the system Erlang capacity. The study demonstrates that with proper deployment of RSs and use of MIMO transmission...

Relay Coordination in the Protection of Radially-Connected Power ...

African Journals Online (AJOL)

Protective relays detect intolerable or unwanted conditions within an assigned area, and then trip or open one or more circuit breakers to isolate the problem area before it can damage or otherwise interfere with the eective operation of the rest of the power system. It often happens that a substation feeder relay and ...

On the capacity of multiple cognitive links through common relay under spectrum-sharing constraints

KAUST Repository

Yang, Yuli

2011-06-01

In this paper, we consider an underlay cognitive relaying network consisting of multiple secondary users and introduce a cooperative transmission protocol using a common relay to help with the communications between all secondary source-destination pairs for higher throughput and lower realization complexity. A whole relay-assisted transmission procedure is composed of multiple access phase and broadcast phase, where the relay is equipped with multiple antennas, and the secondary sources and destinations are single-antenna nodes. Considering the spectrum-sharing constraints on the secondary sources and the relay, we analyze the capacity behaviors of the underlay cognitive relaying network under study. The corresponding numerical results provide a convenient tool for the presented network design and substantiate a distinguishing feature of introduced design in that multiple secondary users\\' communications do not rely on multiple relays, hence allowing for a more efficient use of the radio resources. © 2011 IEEE.

Social-Aware Relay Selection for Cooperative Multicast Device-to-Device Communications

Directory of Open Access Journals (Sweden)

Francesco Chiti

2017-12-01

Full Text Available The increasing use of social networks such as Facebook, Twitter, and Instagram to share photos, video streaming, and music among friends has generated a huge increase in the amount of data traffic over wireless networks. This social behavior has triggered new communication paradigms such as device-to-device (D2D and relaying communication schemes, which are both considered as strong drivers for the next fifth-generation (5G cellular systems. Recently, the social-aware layer and its relationship to and influence on the physical communications layer have gained great attention as emerging focus points. We focus here on the case of relaying communications to pursue the multicast data dissemination to a group of users forming a social community through a relay node, according to the extension of the D2D mode to the case of device-to-many devices. Moreover, in our case, the source selects the device to act as the relay among different users of the multicast group by taking into account both the propagation link conditions and the relay social-trust level with the constraint of minimizing the end-to-end content delivery delay. An optimization procedure is also proposed in order to achieve the best performance. Finally, numerical results are provided to highlight the advantages of considering the impact of social level on the end-to-end delivery delay in the integrated social–physical network in comparison with the classical relay-assisted multicast communications for which the relay social-trust level is not considered.

Counterfactual quantum cryptography network with untrusted relay

Science.gov (United States)

Chen, Yuanyuan; Gu, Xuemei; Jiang, Dong; Xie, Ling; Chen, Lijun

2015-07-01

Counterfactual quantum cryptography allows two remote parties to share a secret key even though a physical particle is not in fact transmitted through the quantum channel. In order to extend the scope of counterfactual quantum cryptography, we use an untrusted relay to construct a multi-user network. The implementation issues are discussed to show that the scheme can be realized with current technologies. We also prove the practical security advantages of the scheme by eliminating the probability that an eavesdropper can directly access the signal or an untrusted relay can perform false operations.

Generator for X-ray diagnostics with mAs-relay

International Nuclear Information System (INIS)

Franke, K.

1978-01-01

The invention concerns a generator for X-ray diagnostics with mAs-relay, which is provided with organ keys for organ-programmed selection of mAs-products. For individual setting of the recording time the mAs-relay input is connected to an auxiliary source of current supplying a constant auxiliary current. The response barrier of the mAs-relay is thereby set by time set average. For overload protection may be used a power circuit which at exceeding the programmed times, e.g. the times provided for tomography operation, reduces the X-ray tube power step by step to allowed values by means of the X-ray tube current. (orig.) [de

Throughput maximization for buffer-aided hybrid half-/full-duplex relaying with self-interference

KAUST Repository

Khafagy, Mohammad Galal

2015-06-01

In this work, we consider a two-hop cooperative setting where a source communicates with a destination through an intermediate relay node with a buffer. Unlike the existing body of work on buffer-aided half-duplex relaying, we consider a hybrid half-/full-duplex relaying scenario with loopback interference in the full-duplex mode. Depending on the channel outage and buffer states that are assumed available at the transmitters, the source and relay may either transmit simultaneously or revert to orthogonal transmission. Specifically, a joint source/relay scheduling and relaying mode selection mechanism is proposed to maximize the end-to-end throughput. The throughput maximization problem is converted to a linear program where the exact global optimal solution is efficiently obtained via standard convex/linear numerical optimization tools. Finally, the theoretical findings are corroborated with event-based simulations to provide the necessary performance validation.

Outage Probability versus Fairness Trade-off in Opportunistic Relay Selection with Outdated CSI

Directory of Open Access Journals (Sweden)

Vicario JoseLopez

2009-01-01

Full Text Available We analyze the existing trade-offs in terms of system performance versus fairness of a cooperative system based on opportunistic relay selection (ORS and with outdated channel state information (CSI. In particular, system performance is analytically evaluated in terms of outage probability, and the fairness behavior is assessed based on the power consumption at the different relays. In order to improve the fairness behavior of ORS while keeping the selection diversity gain, we propose a relay selection mechanism where the relay with the highest normalized signal-to-noise ratio (SNR is selected for relaying the source's information. The proposed strategy is compared with existing relay selection strategies by adopting a novel graphical representation inspired by expected profit versus risk plots used in modern portfolio theory. As shown in the paper, this strategy allows operating the system in more favorable points of the outage versus fairness region.

Precoder Design and Power Allocation for MIMO Cognitive Radio Two-Way Relaying Systems

KAUST Repository

Sboui, Lokman

2016-08-11

In this paper, we study a multiple-antenna two-way relaying (TWR) cognitive radio (CR) system. A space alignment (SA) technique is adopted by the secondary users (SUs) to avoid interference with the primary users (PUs). We derive the optimal power allocation that maximizes the TWR achievable SU sum- rate while respecting the total power budget and the relay power constraints. We also analyze the case in which the relay is able to optimize its gain matrix structure to enhance the SU sum-rate. In the numerical results, we quantify the sum-rate gain of using the SA in the TWR CR and we show that the SU sum-rate is very limited when the relay power is low or the PU power and its resulting interference are high. In addition, we optimize the relay gain using an iterative algorithm and compare between different relay matrix structures.

PPM-based relay communication schemes for wireless body area networks

NARCIS (Netherlands)

Zhang, P.; Willems, F.M.J.; Huang, Li

2012-01-01

This paper investigates cooperative communication schemes based on a single relay with pulse-position modulation (PPM) signaling, for enhancing energy efficiency of wireless body area networks (WBANs) in noncoherent channel settings. We explore cooperation between the source and the relay such that

Protective Relay Studies for the Nigerian National Electric 330 KV ...

African Journals Online (AJOL)

The fundamental reasons for requiring these specific protective relaying features are also reviewed. Other protective relaying schemes that can accomplish the same basic protection objectives are presented. Based on the Nigerian special system characteristics, schemes to correct existing protection inadequacies are ...

On the benefits of location-based relay selection in mobile wireless networks

DEFF Research Database (Denmark)

Nielsen, Jimmy Jessen; Madsen, Tatiana Kozlova; Schwefel, Hans-Peter

2016-01-01

We consider infrastructure-based mobile networks that are assisted by a single relay transmission where both the downstream destination and relay nodes are mobile. Selecting the optimal transmission path for a destination node requires up-to-date link quality estimates of all relevant links....... If the relay selection is based on link quality measurements, the number of links to update grows quadratically with the number of nodes, and measurements need to be updated frequently when nodes are mobile. In this paper, we consider a location-based relay selection scheme where link qualities are estimated...... from node positions; in the scenario of a node-based location system such as GPS, the location-based approach reduces signaling overhead, which in this case only grows linearly with the number of nodes. This paper studies these two relay selection approaches and investigates how they are affected...

Performance Analysis of Relays in LTE for a Realistic Suburban Deployment Scenario

DEFF Research Database (Denmark)

Coletti, Claudio; Mogensen, Preben; Irmer, Ralf

2011-01-01

Relays are likely to play an important role in the deployment of Beyond 3G networks, such as LTE-Advanced, thanks to the possibility of effectively extending Macro network coverage and fulfilling the expected high data-rate requirements. Up until now, the relay technology potential and its cost......-effectiveness have been widely investigated in the literature, considering mainly statistical deployment scenarios, like regular networks with uniform traffic distribution. This paper is envisaged to illustrate the performances of different relay technologies (In-Band/Out-band) in a realistic suburban network...... scenario with real Macro site positions, user density map and spectrum band availability. Based on a proposed heuristic deployment algorithm, results show that deploying In-band relays can significantly reduce the user outage if high backhaul link quality is ensured, whereas Out-band relaying and the usage...

An automated thermoelectric power apparatus using electro-optic relays

International Nuclear Information System (INIS)

Chakravarti, A.; Ranganathan, R.

1992-01-01

We report the design and construction of a thermoelectric power apparatus using home-made electro-optic relays with Z-80A microprocessor for automatic data acquisition and control. The advantages of such relays made out of LED-LDR combinations for the measurement of ΔE and ΔT are discussed in details. (author). 7 refs., 5 figs

Simultaneous Wireless Information and Power Transfer for MIMO Amplify-and-Forward Relay Systems

KAUST Repository

Benkhelifa, Fatma

2016-03-28

© 2015 IEEE. In this paper, we investigate two-hop Multiple- Input Multiple-Output (MIMO) Amplify-and-Forward (AF) relay communication systems with simultaneous wireless information and power transfer (SWIPT) at the multi-antenna energy harvesting relay. We derive the optimal source and relay covariance matrices to characterize the achievable region between the source-destination rate and the harvested energy at the relay, namely Rate-Energy (R-E) region. In this context, we consider the ideal scenario where the energy harvester (EH) receiver and the information decoder (ID) receiver at the relay can simultaneously decode the information and harvest the energy at the relay. This scheme provides an outer bound for the achievable R-E region since practical energy harvesting circuits are not yet able to harvest the energy and decode the information simultaneously. Then, we consider more practical schemes which are the power splitting (PS) and the time switching (TS) proposed in [1] and which separate the EH and ID transfer over the power domain and the time domain, respectively. In our study, we derive the boundary of the achievable R- E region and we show the effect of the source transmit power, the relay transmit power and the position of the relay between the source and the destination on the achievable R-E region for the ideal scenario and the two practical schemes.

Alternate MIMO AF relaying networks with interference alignment: Spectral efficient protocol and linear filter design

KAUST Repository

Park, Kihong

2013-02-01

In this paper, we study a two-hop relaying network consisting of one source, one destination, and three amplify-and-forward (AF) relays with multiple antennas. To compensate for the capacity prelog factor loss of 1/2$ due to the half-duplex relaying, alternate transmission is performed among three relays, and the inter-relay interference due to the alternate relaying is aligned to make additional degrees of freedom. In addition, suboptimal linear filter designs at the nodes are proposed to maximize the achievable sum rate for different fading scenarios when the destination utilizes a minimum mean-square error filter. © 1967-2012 IEEE.

Line Differential Protection Scheme Modelling for Underground 420 kV Cable Systems, EMTDC/PSCAD Relays Modelling

DEFF Research Database (Denmark)

Bak, Claus Leth; Sztykiel, Michal; Dollerup, Sebastian

2011-01-01

Based on the analysis of a specific relay model and an HVAC (High Voltage Alternating Current) cable system, a new approach to EMTDC/PSCAD modelling of protective relays is presented. Such approach allows creating complex and accurate relay models derived from the original algorithms. Relay models...... can be applied with various systems, allowing obtaining the most optimal configuration of the protective relaying. The present paper describes modelling methodology on the basis of Siemens SIPROTEC 4 7SD522/610. Relay model was verified experimentally with its real equivalent by both EMTP......-simulated and real world generated current signals connected to the relay....

Half-Duplex and Full-Duplex AF and DF Relaying with Energy-Harvesting in Log-Normal Fading

KAUST Repository

Rabie, Khaled M.

2017-08-15

Energy-harvesting (EH) and wireless power transfer in cooperative relaying networks have recently attracted a considerable amount of research attention. Most of the existing work on this topic however focuses on Rayleigh fading channels, which represent outdoor environments. In contrast, this paper is dedicated to analyze the performance of dual-hop relaying systems with EH over indoor channels characterized by log-normal fading. Both half-duplex (HD) and full-duplex (FD) relaying mechanisms are studied in this work with decode-and-forward (DF) and amplify-and-forward (AF) relaying protocols. In addition, three EH schemes are investigated, namely, time switching relaying, power splitting relaying and ideal relaying receiver which serves as a lower bound. The system performance is evaluated in terms of the ergodic outage probability for which we derive accurate analytical expressions. Monte Carlo simulations are provided throughout to validate the accuracy of our analysis. Results reveal that, in both HD and FD scenarios, AF relaying performs only slightly worse than DF relaying which can make the former a more efficient solution when the processing energy cost at the DF relay is taken into account. It is also shown that FD relaying systems can generally outperform HD relaying schemes as long as the loop-back interference in FD is relatively small. Furthermore, increasing the variance of the log-normal channel has shown to deteriorate the performance in all the relaying and EH protocols considered.

Cache Aided Decode-and-Forward Relaying Networks: From the Spatial View

Directory of Open Access Journals (Sweden)

Junjuan Xia

2018-01-01

Full Text Available We investigate cache technique from the spatial view and study its impact on the relaying networks. In particular, we consider a dual-hop relaying network, where decode-and-forward (DF relays can assist the data transmission from the source to the destination. In addition to the traditional dual-hop relaying, we also consider the cache from the spatial view, where the source can prestore the data among the memories of the nodes around the destination. For the DF relaying networks without and with cache, we study the system performance by deriving the analytical expressions of outage probability and symbol error rate (SER. We also derive the asymptotic outage probability and SER in the high regime of transmit power, from which we find the system diversity order can be rapidly increased by using cache and the system performance can be significantly improved. Simulation and numerical results are demonstrated to verify the proposed studies and find that the system power resources can be efficiently saved by using cache technique.

Diversity-Multiplexing Trade-off for Coordinated Direct and Relay Schemes

DEFF Research Database (Denmark)

Thai, Chan; Popovski, Petar; De Carvalho, Elisabeth

2013-01-01

The recent years have brought a significant body of research on wireless Two-Way Relaying (TWR), where the use of network coding brings an evident advantage in terms of data rates. Yet, TWR scenarios represent only a special case and it is of interest to devise similar techniques in more general...... Direct/Relay (CDR) schemes, which involve two flows, of a direct and a relayed user. In this paper we characterize a CDR scheme by deriving/bounding the Diversity-Multiplexing Trade-off (DMT) function. Two cases are considered. In the first case a transmitter knows the Channel State Information (CSI...

NRC Information No. 88-98: Electrical relay degradation caused by oxidation of contact surfaces

International Nuclear Information System (INIS)

Rossi, C.E.

1992-01-01

The NRC staff was recently informed by Clinton Power Station that a reactor scram on June 24, 1988, was caused by an electrical relay failure from oxide buildup on relay contact surfaces. Other information on relay failure from contact oxidation indicates that this problem may be more prevalent than previously thought. For example, a July 17, 1988, 10 CFR Part 21 report from Palo Verde, Unit 2, reported relay failures from contact oxidation that were due to the low current application of the relays. The relay contact surfaces in both of these examples are silver-nickel alloys, and both applications were for low current (i.e., milli-ampere current). Electrical relay contacts made of silver-nickel or silver-cadmium alloys will oxidize (tarnish) when used in low current applications because of the absence of contact surface sparking from the typical relay contact ''making and breaking'' functions. The sparking in the contact surfaces promotes a self-cleaning mechanism that reduces the tarnish buildup on the silver-nickel or silver-cadmium contacts. Discussions with one relay manufacturer revealed that the normal industry practice for low current circuit applications is either to use a contact surface material that will not oxidize or to compensate for the oxidation by increased maintenance activities to ensure reliability. The applied voltage may also influence contact oxidation

Simulation of Distance Relay for Load Encroachment Alleviation with Agent Based Supervision of Zone3

Directory of Open Access Journals (Sweden)

Mohamed Badr

2017-03-01

Full Text Available Cascaded tripping of power lines due to mal-operation of zone-3 distance relays has been one of the main causes of many previous blackouts worldwide. Encroachment of load into zone-3 characteristics during stressed system operation conditions is a basic factor for such mal-operation of the relays. By improving the operation of zone-3, it is possible to prevent mal-operations so that cascaded line tripping can be avoided. For proper study of the behavior of distance relay during faults and load encroachment phenomenon, we must build a model of distance relay, so in this paper a modeling study of distance relay is implemented using MATLAB/Simulink program. However, this model is distinguished from previous models that, examines in detail the third zone of distance relay. Many cases are simulated with changing line loading and fault location to ensure the capability of the relay to detect the fault and thus the maximum load ability limit of distance relay is obtained. In order to prevent cascading events caused by hidden failures in zone-3 relays, agent based relay architectures have been suggested in the recent past. In such architectures each zone-3 relay contains agents that require communication with other agents at various relevant relays in order to distinguish a real zone-3 event from a temporary overload. In this paper, a local master agent is consulted by all zone-3 agents before a tripping decision is made. The master agent maintains a rule base which is updated based on the local topology of the network and real time monitoring of the status of other relays and circuit breakers. Cisco Packet Tracer program is used for running communication network simulations. The result of the simulation indicate that the time estimated to send and receive a packet data unit (PDU message between one relay to anther can satisfy the communication requirement for the proposed scheme with fiber media.

On Amplify-and-Forward Relaying Over Hyper-Rayleigh Fading Channels

Directory of Open Access Journals (Sweden)

S. H. Alvi

2014-12-01

Full Text Available Relayed transmission holds promise for the next generation of wireless communication systems due to the performance gains it can provide over non-cooperative systems. Recently hyper-Rayleigh fading, which represents fading conditions more severe than Rayleigh fading, has received attention in the context of many practical communication scenarios. Though power allocation for Amplify-and-Forward (AF relaying networks has been studied in the literature, a theoretical analysis of the power allocation problem for hyper-Rayleigh fading channels is a novel contribution of this work. We develop an optimal power allocation (OPA strategy for a dual-hop AF relaying network in which the relay-destination link experiences hyper-Rayleigh fading. A new closed-form expression for the average signal-to-noise ratio (SNR at destination is derived and it is shown to provide a new upper-bound on the average SNR at destination, which outperforms a previously proposed upper-bound based on the well-known harmonic-geometric mean inequality. An OPA across the source and relay nodes, subject to a sum-power constraint, is proposed and it is shown to provide measurable performance gains in average SNR and SNR outage at the destination relative to the case of equal power allocation.

Partial relay selection based on shadowing side information over generalized composite fading channels

KAUST Repository

Yilmaz, Ferkan

2011-11-01

In this paper, in contrast to the relay selection protocols available in the literature, we propose a partial relay selection protocol utilizing only the shadowing side information of the relays instead of their full channel side information in order to select a relay in a dual-hop relaying system through the available limited feedback channels and power budget. We then presented an exact unified performance expression combining the average bit error probability, ergodic capacity, and moments-generating function of the proposed partial relay selection over generalized fading channels. Referring to the unified performance expression introduced in [1], we explicitly offer a generic unified performance expression that can be easily calculated and that is applicable to a wide variety of fading scenarios. Finally, as an illustration of the mathematical formalism, some numerical and simulation results are generated for an extended generalized-K fading environment, and these numerical and simulation results are shown to be in perfect agreement. © 2011 IEEE.

A study of optimization problem for amplify-and-forward relaying over weibull fading channels

KAUST Repository

Ikki, Salama Said; Aissa, Sonia

2010-01-01

This paper addresses the power allocation and relay positioning problems in amplify-and-forward cooperative networks operating in Weibull fading environments. We study adaptive power allocation (PA) with fixed relay location, optimal relay location

CERN Relay Race 2018

CERN Document Server

CERN Running club

2018-01-01

The CERN running club, in collaboration with the Staff Association, is happy to announce the 2018 relay race edition. It will take place on Thursday, May 24th and will consist as every year in a round trip of the CERN Meyrin site in teams of 6 members. It is a fun event, and you do not have to run fast to enjoy it. Registrations will be open from May 1st to May 22nd on the running club web site. All information concerning the race and the registration are available there too: http://runningclub.web.cern.ch/content/cern-relay-race. A video of the previous edition is also available here : http://cern.ch/go/Nk7C. As every year, there will be animations starting at noon on the lawn in front of restaurant 1, and information stands for many CERN associations and clubs will be available. The running club partners will also be participate in the event, namely Berthie Sport, Interfon and Uniqa.

Relays undergo seismic tests

International Nuclear Information System (INIS)

Burton, J.C.

1977-01-01

Utilities are required by the Nuclear Regulatory Commission to document that seismic vibration will not adversely affect critical electrical equipment. Seismic testing should be designed to determine the malfunction level (fragility testing). Input possibilities include a continuous sine, a decaying sine, a sine beat, random vibrations, and combinations of random vibrations and sine beat. The sine beat most accurately simulates a seismic event. Test frequencies have a broad range in order to accommodate a variety of relay types and cabinet mounting. Simulation of motion along three axes offers several options, but is best achieved by three in-phase single-axis vibration machines that are less likely to induce testing fatigue failure. Consensus on what constitutes relay failure favors a maximum two microsecond discontinuity. Performance tests should be conducted for at least two of the following: (1) nonoperating modes, (2) operating modes, or (3) the transition above the two modes, with the monitoring mode documented for all three. Results should specify a capability curve of maximum safe seismic acceleration and a graph plotting acceleration with sine-beat frequency

Error-rate performance analysis of cooperative OFDMA system with decode-and-forward relaying

KAUST Repository

Fareed, Muhammad Mehboob; Uysal, Murat; Tsiftsis, Theodoros A.

2014-01-01

In this paper, we investigate the performance of a cooperative orthogonal frequency-division multiple-access (OFDMA) system with decode-and-forward (DaF) relaying. Specifically, we derive a closed-form approximate symbol-error-rate expression and analyze the achievable diversity orders. Depending on the relay location, a diversity order up to (LSkD + 1) + σ M m = 1 min(LSkRm + 1, LR mD + 1) is available, where M is the number of relays, and LS kD + 1, LSkRm + 1, and LRmD + 1 are the lengths of channel impulse responses of source-to-destination, source-to- mth relay, and mth relay-to-destination links, respectively. Monte Carlo simulation results are also presented to confirm the analytical findings. © 2013 IEEE.

Error-rate performance analysis of cooperative OFDMA system with decode-and-forward relaying

KAUST Repository

Fareed, Muhammad Mehboob

2014-06-01

In this paper, we investigate the performance of a cooperative orthogonal frequency-division multiple-access (OFDMA) system with decode-and-forward (DaF) relaying. Specifically, we derive a closed-form approximate symbol-error-rate expression and analyze the achievable diversity orders. Depending on the relay location, a diversity order up to (LSkD + 1) + σ M m = 1 min(LSkRm + 1, LR mD + 1) is available, where M is the number of relays, and LS kD + 1, LSkRm + 1, and LRmD + 1 are the lengths of channel impulse responses of source-to-destination, source-to- mth relay, and mth relay-to-destination links, respectively. Monte Carlo simulation results are also presented to confirm the analytical findings. © 2013 IEEE.

Accurate performance analysis of opportunistic decode-and-forward relaying

KAUST Repository

Tourki, Kamel

2011-07-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path may be considered unusable, and the destination may use a selection combining technique. We first derive the exact statistics of each hop, in terms of probability density function (PDF). Then, the PDFs are used to determine accurate closed form expressions for end-to-end outage probability for a transmission rate R. Furthermore, we evaluate the asymptotical performance analysis and the diversity order is deduced. Finally, we validate our analysis by showing that performance simulation results coincide with our analytical results over different network architectures. © 2011 IEEE.

Reliability Analysis of Differential Relay as Main Protection Transformer Using Fuzzy Logic Algorithm

Science.gov (United States)

Mulyadi, Y.; Sucita, T.; Sumarto; Alpani, M.

2018-02-01

Electricity supply demand is increasing every year. It makes PT. PLN (Persero) is required to provide optimal customer service and satisfaction. Optimal service depends on the performance of the equipment of the power system owned, especially the transformer. Power transformer is an electrical equipment that transforms electricity from high voltage to low voltage or vice versa. However, in the electrical power system, is inseparable from interference included in the transformer. But, the disturbance can be minimized by the protection system. The main protection transformer is differential relays. Differential relays working system using Kirchoff law where inflows equal outflows. If there are excessive currents that interfere then the relays will work. But, the relay can also experience decreased performance. Therefore, this final project aims to analyze the reliability of the differential relay on the transformer in three different substations. Referring to the standard applied by the transmission line protection officer, the differential relay shall have slope characteristics of 30% in the first slope and 80% in the second slope when using two slopes and 80% when using one slope with an instant time and the corresponding ratio. So, the results obtained on the Siemens differential release have a reliable slope characteristic with a value of 30 on the fuzzy logic system. In a while, ABB a differential relay is only 80% reliable because two experiments are not reliable. For the time, all the differential relays are instant with a value of 0.06 on the fuzzy logic system. For ratios, the differential relays ABB have a better value than others brand with a value of 151 on the fuzzy logic system.

Tests of microprocessor-based relay protection devices: Problems and solutions

Directory of Open Access Journals (Sweden)

Gurevich Vladimir

2009-01-01

Full Text Available Usually, the operational condition of relay protection devices is checked with specific settings used for the relay operation in a certain network point. In the author's opinion in order to verify the proper operation of complex multifunctional microprocessor-based protection devices (MPD at their inspection, start-up after repairs or during periodic tests there is no need to use the actual settings at which the relay is to be operated in a certain network's point. It should be tested for proper operation at several of its most critical preset characteristic points as well as in several preset characteristics constituting its most complicated (combined operation modes, including the dynamic operation modes with preset transition processes specific for standard power networks (not necessarily for a specific point. The proposed set of actions for the unification of software platforms of the modern, microprocessor-based relay protection test systems will enable examination of modern MPD in an absolutely new way. .

Error-rate performance analysis of incremental decode-and-forward opportunistic relaying

KAUST Repository

Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim

2011-01-01

In this paper, we investigate an incremental opportunistic relaying scheme where the selected relay chooses to cooperate only if the source-destination channel is of an unacceptable quality. In our study, we consider regenerative relaying in which the decision to cooperate is based on a signal-to-noise ratio (SNR) threshold and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We derive a closed-form expression for the end-to-end bit-error rate (BER) of binary phase-shift keying (BPSK) modulation based on the exact probability density function (PDF) of each hop. Furthermore, we evaluate the asymptotic error performance and the diversity order is deduced. We show that performance simulation results coincide with our analytical results. © 2011 IEEE.

Error-rate performance analysis of incremental decode-and-forward opportunistic relaying

KAUST Repository

Tourki, Kamel

2010-10-01

In this paper, we investigate an incremental opportunistic relaying scheme where the selected relay chooses to cooperate only if the source-destination channel is of an unacceptable quality. In our study, we consider regenerative relaying in which the decision to cooperate is based on a signal-to-noise ratio (SNR) threshold and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We derive a closed-form expression for the end-to-end biterror rate (BER) of binary phase-shift keying (BPSK) modulation based on the exact probability density function (PDF) of each hop. Furthermore, we evaluate the asymptotic error performance and the diversity order is deduced. We show that performance simulation results coincide with our analytical results. ©2010 IEEE.

Error-rate performance analysis of incremental decode-and-forward opportunistic relaying

KAUST Repository

Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim

2010-01-01

In this paper, we investigate an incremental opportunistic relaying scheme where the selected relay chooses to cooperate only if the source-destination channel is of an unacceptable quality. In our study, we consider regenerative relaying in which the decision to cooperate is based on a signal-to-noise ratio (SNR) threshold and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We derive a closed-form expression for the end-to-end biterror rate (BER) of binary phase-shift keying (BPSK) modulation based on the exact probability density function (PDF) of each hop. Furthermore, we evaluate the asymptotic error performance and the diversity order is deduced. We show that performance simulation results coincide with our analytical results. ©2010 IEEE.

Location-quality-aware policy optimisation for relay selection in mobile networks

DEFF Research Database (Denmark)

Nielsen, Jimmy Jessen; Olsen, Rasmus Løvenstein; Madsen, Tatiana Kozlova

2016-01-01

for resulting performance of such network optimizations. In mobile scenarios, the required information collection and forwarding causes delays that will additionally affect the reliability of the collected information and hence will influence the performance of the relay selection method. This paper analyzes...... the joint influence of these two factors in the decision process for the example of a mobile location-based relay selection approach using a continuous time Markov chain model. Efficient algorithms are developed based on this model to obtain optimal relay policies under consideration of localization errors....... Numerical results show how information update rates, forwarding delays, and location estimation errors affect these optimal policies and allow to conclude on the required accuracy of location-based systems for such mobile relay selection scenarios. A measurement-based indoor scenario with more complex...

Error-rate performance analysis of incremental decode-and-forward opportunistic relaying

KAUST Repository

Tourki, Kamel

2011-06-01

In this paper, we investigate an incremental opportunistic relaying scheme where the selected relay chooses to cooperate only if the source-destination channel is of an unacceptable quality. In our study, we consider regenerative relaying in which the decision to cooperate is based on a signal-to-noise ratio (SNR) threshold and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We derive a closed-form expression for the end-to-end bit-error rate (BER) of binary phase-shift keying (BPSK) modulation based on the exact probability density function (PDF) of each hop. Furthermore, we evaluate the asymptotic error performance and the diversity order is deduced. We show that performance simulation results coincide with our analytical results. © 2011 IEEE.

Nonconformance in electromechanical output relays of microprocessor-based protection devices under actual operating conditions

OpenAIRE

Gurevich, Vladimir

2006-01-01

Microprocessor-based protection relays are gradually driving out traditional electromechanical and even electronic protection devices from virtually all fields of power and electrical engineering. In this paper, one of many problems of microprocessor-based relays is discussed: nonconformance of miniature electromechanical output relays under actual operation conditions: switching inductive loads (with tripping CB coils or lockout relay coils) at 220 VDC, and "dry" switching of some control ci...

49 CFR 236.206 - Battery or power supply with respect to relay; location.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Battery or power supply with respect to relay..., AND APPLIANCES Automatic Block Signal Systems Standards § 236.206 Battery or power supply with respect to relay; location. The battery or power supply for each signal control relay circuit, where an open...

47 CFR 64.606 - VRS and IP Relay provider and TRS program certification.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 3 2010-10-01 2010-10-01 false VRS and IP Relay provider and TRS program... Services and Related Customer Premises Equipment for Persons With Disabilities § 64.606 VRS and IP Relay... including notification in the Federal Register. (2) VRS and IP Relay provider. Any entity desiring to...

Deep space optical communication via relay satellite

Science.gov (United States)

Dolinar, S.; Vilnrotter, V.; Gagliardi, R.

1981-01-01

The application of optical communications for a deep space link via an earth-orbiting relay satellite is discussed. The system uses optical frequencies for the free-space channel and RF links for atmospheric transmission. The relay satellite is in geostationary orbit and contains the optics necessary for data processing and formatting. It returns the data to earth through the RF terrestrial link and also transmits an optical beacon to the satellite for spacecraft return pointing and for the alignment of the transmitting optics. Future work will turn to modulation and coding, pointing and tracking, and optical-RF interfacing.

2005 CERN Relay Race

CERN Multimedia

Patrice Loiez

2005-01-01

The CERN Relay Race takes place each year in May and sees participants from all areas of the CERN staff. The winners in 2005 were The Shabbys with Los Latinos Volantes in second and Charmilles Technologies a close third. To add a touch of colour and levity, the CERN Jazz Club provided music at the finishing line.

Staged-Fault Testing of Distance Protection Relay Settings

Science.gov (United States)

Havelka, J.; Malarić, R.; Frlan, K.

2012-01-01

In order to analyze the operation of the protection system during induced fault testing in the Croatian power system, a simulation using the CAPE software has been performed. The CAPE software (Computer-Aided Protection Engineering) is expert software intended primarily for relay protection engineers, which calculates current and voltage values during faults in the power system, so that relay protection devices can be properly set up. Once the accuracy of the simulation model had been confirmed, a series of simulations were performed in order to obtain the optimal fault location to test the protection system. The simulation results were used to specify the test sequence definitions for the end-to-end relay testing using advanced testing equipment with GPS synchronization for secondary injection in protection schemes based on communication. The objective of the end-to-end testing was to perform field validation of the protection settings, including verification of the circuit breaker operation, telecommunication channel time and the effectiveness of the relay algorithms. Once the end-to-end secondary injection testing had been completed, the induced fault testing was performed with three-end lines loaded and in service. This paper describes and analyses the test procedure, consisting of CAPE simulations, end-to-end test with advanced secondary equipment and staged-fault test of a three-end power line in the Croatian transmission system.

Energy efficient design for MIMO two-way AF multiple relay networks

KAUST Repository

Alsharoa, Ahmad M.; Ghazzai, Hakim; Alouini, Mohamed-Slim

2014-01-01

This paper studies the energy efficient transmission and the power allocation problem for multiple two-way relay networks equipped with multi-input multi-output antennas where each relay employs an amplify-and-forward strategy. The goal

Simultaneous energy harvesting and information processing in wireless multiple relays with multiple antennas

Science.gov (United States)

Albaaj, Azhar; Makki, S. Vahab A.; Alabkhat, Qassem; Zahedi, Abdulhamid

2017-07-01

Wireless networks suffer from battery discharging specially in cooperative communications when multiple relays have an important role but they are energy constrained. To overcome this problem, energy harvesting from radio frequency signals is applied to charge the node battery. These intermediate nodes have the ability to harvest energy from the source signal and use the energy harvested to transmit information to the destination. In fact, the node tries to harvest energy and then transmit the data to destination. Division of energy harvesting and data transmission can be done in two algorithms: time-switching-based relaying protocol and power-splitting-based relaying protocol. These two algorithms also can be applied in delay-limited and delay-tolerant transmission systems. The previous works have assumed a single relay for energy harvesting, but in this article, the proposed method is concentrated on improving the outage probability and throughput by using multiple antennas in each relay node instead of using single antenna. According to our simulation results, when using multi-antenna relays, ability of energy harvesting is increased and thus system performance will be improved to great extent. Maximum ratio combining scheme has been used when the destination chooses the best signal of relays and antennas satisfying the required signal-to-noise ratio.

Considering Pilot Protection in the Optimal Coordination of Distance and Directional Overcurrent Relays

Directory of Open Access Journals (Sweden)